{"catalog":{"ledgerFiles":[{"subject":"a2-flash-hider","title":"Mil-spec A2 flash hider, 1/2-28 (drawing 9349051)","dimensions":{"compensator_length":{"label":"Compensator, overall length (rear face to front face)","kind":"length","measurements":[{"id":"tdp","value":1.75,"unit":"in","pm":0.01,"stated":"1.76 -.02, from the rear face (datum A)","source":{"type":"standard","doc":"US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p176","via":"user"}},{"id":"spikes","value":1.75,"unit":"in","stated":"Length: 1.75\" Length","source":{"type":"spec","publisher":"manufacturer","name":"Spike's Tactical (its A2 flash hider, 1/2x28, \"Mil-Spec Heavy Phosphate Finish\")","url":"https://www.spikestactical.com/collections/muzzle-devices/flash-hider-a2/","retrieved":"2026-10-01","via":"harvest"}},{"id":"kak","value":1.75,"unit":"in","stated":"Overall Length- 1.750\"","source":{"type":"spec","publisher":"manufacturer","name":"KAK Industry (its A2 birdcage flash hider, \"Phosphate Coated\")","url":"https://kakindustry.com/a2-birdcage-flash-hider","retrieved":"2026-10-01","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing; two makers' own pages state the same."},"note":"Makers of A2s state the same length: Spike's, Faxon, KAK, Ballistic Barn and Wing Tactical's listings of Aero's and Spike's all say 1.75 in."},"od":{"label":"Largest outside diameter (the rear section and the front ring)","kind":"length","measurements":[{"id":"tdp","value":0.862,"unit":"in","pm":0.002,"stated":".864 -.004 Ø (datum C)","source":{"type":"standard","doc":"US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p176","via":"user"}},{"id":"wing-aero","value":0.86,"unit":"in","stated":"Diameter: 0.86\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical (Aero Precision's A2 birdcage flash hider, \"Mil-Spec Heavy Phosphate\")","url":"https://www.wingtactical.com/firearm-parts/ar-15/muzzle-devices/aero-precision-a2-birdcage-flash-hider-5-56-223/","retrieved":"2026-10-01","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing; a retailer's figure for Aero's agrees."},"note":"Dimensioned at the front end, where its extension lines leave the outline; the rear section is drawn at the same height, and on Windham's part the front ring measures 0.867 ± 0.007 against the rear section taken as this (tools/turned.py: 223.7 px against 222.4): the same within the ±."},"cage_od":{"label":"Slotted cage, outside diameter (between the rear section and the front ring)","kind":"length","measurements":[{"id":"tdp","value":0.834,"unit":"in","pm":0.01,"stated":".844 -.020 Ø","source":{"type":"standard","doc":"US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p176","via":"user"}},{"id":"windham","value":0.833,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/a2-flash-hider edeff5c5fbd9 (Windham Weaponry A2 flash hider, their part 9349051; straight side view on white, 1000 x 600)","scaleRef":"the same part's rear section in the same photo, taken as od (.862): 222.4 px radius on both lands, top and bottom (516 px/in)","method":"tools/turned.py: radius from the part's own axis (a line through the mid-heights of the lands and the front ring; tilt 0.12°), 50% edges","via":"harvest"},"note":"On the closed side, where no slot cuts the edge: 214.97 px over the cage's middle 0.6 in (spread 0.1). The top edge there is the top slot's rim (213.5 px), not the cage."}],"adopt":{"from":"tdp","reason":"The drawing. A real part's photo reads the same to 0.001."},"note":"Which section this callout belongs to isn't plain from the scan: its extension lines run just inside the .864's, and the outline is drawn almost at one height throughout (310 px over the rear section, 308 over the cage, where .020 in would be 7 px). It is the cage: on a real part the cage is the smaller section (windham), and the drawing's 43° chamfer is called out in 2 PLACES, one at each end of it. First read as the front ring's and corrected before anything was built on it."},"step_angle":{"label":"Steps at the two ends of the cage, chamfer angle (from square to the axis)","kind":"angle","measurements":[{"id":"tdp","value":45,"unit":"deg","pm":2,"stated":"43° +4°, 2 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p176","via":"user"}}]},"rear_length":{"label":"Rear section, length (rear face to the step down to the cage)","kind":"length","measurements":[{"id":"tdp","value":0.72,"unit":"in","pm":0.01,"stated":".73 -.02","source":{"type":"standard","doc":"US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p176","via":"user"}}],"note":"The section with the wrench flats and the two grooves. On Windham's part the step is 0.120 ahead of the second groove's front wall, where these callouts put it (.73 less .49 less .11) at 0.13."},"cage_length":{"label":"Slotted cage, length (between its two steps)","kind":"length","measurements":[{"id":"tdp","value":0.8,"unit":"in","pm":0.01,"stated":".79 +.02","source":{"type":"standard","doc":"US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p176","via":"user"}},{"id":"windham","value":0.813,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/a2-flash-hider edeff5c5fbd9 (Windham Weaponry A2 flash hider, their part 9349051; straight side view on white, 1000 x 600)","scaleRef":"the same part's rear section in the same photo, taken as od (.862): 222.4 px radius on both lands, top and bottom (516 px/in)","method":"tools/turned.py: radius from the part's own axis (a line through the mid-heights of the lands and the front ring; tilt 0.12°), 50% edges","via":"harvest"},"note":"Between the two places the closed side's edge crosses the level midway between the rear section's radius and the cage's: 419.5 px."}],"adopt":{"from":"tdp","reason":"The drawing; the photo agrees within the two ±."}},"groove_width":{"label":"Grooves in the rear section, width (two, full-radius bottoms)","kind":"length","measurements":[{"id":"tdp","value":0.12,"unit":"in","pm":0.01,"stated":".11 +.02, 2 PLACES; FULL R, 2 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p176","via":"user"}},{"id":"windham","value":0.128,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/a2-flash-hider edeff5c5fbd9 (Windham Weaponry A2 flash hider, their part 9349051; straight side view on white, 1000 x 600)","scaleRef":"the same part's rear section in the same photo, taken as od (.862): 222.4 px radius on both lands, top and bottom (516 px/in)","method":"tools/turned.py: radius from the part's own axis (a line through the mid-heights of the lands and the front ring; tilt 0.12°), 50% edges","via":"harvest"},"note":"Wall to wall just under the lands' surface (0.007 in below it): 0.129 and 0.127. That high up a broken edge (.005 +.010) is still part of it, so it reads the groove a little wide."}],"adopt":{"from":"tdp","reason":"The drawing; the photo agrees within the two ±."}},"groove_d":{"label":"Grooves in the rear section, diameter at their bottoms","kind":"length","measurements":[{"id":"tdp","value":0.62,"unit":"in","pm":0.01,"stated":".63 -.02 Ø, 2 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p176","via":"user"}},{"id":"windham","value":0.617,"unit":"in","pm":0.007,"source":{"type":"photo","photo":"references/a2-flash-hider edeff5c5fbd9 (Windham Weaponry A2 flash hider, their part 9349051; straight side view on white, 1000 x 600)","scaleRef":"the same part's rear section in the same photo, taken as od (.862): 222.4 px radius on both lands, top and bottom (516 px/in)","method":"tools/turned.py: radius from the part's own axis (a line through the mid-heights of the lands and the front ring; tilt 0.12°), 50% edges","via":"harvest"},"note":"On the top edge: 159.0 and 159.7 px (0.616, 0.619). The bottom edge in the grooves stops 18.5 px short of that (177.6 px), near-black: read as a shadow under the part, since a turned groove has one radius; not used."}],"adopt":{"from":"tdp","reason":"The drawing; the photo agrees to 0.003."}},"groove_1_x":{"label":"First groove's rear edge, from the rear face","kind":"length","measurements":[{"id":"tdp","value":0.22,"unit":"in","pm":0.01,"stated":".23 -.02","source":{"type":"standard","doc":"US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p176","via":"user"}}]},"groove_2_x":{"label":"Second groove's rear edge, from the rear face","kind":"length","measurements":[{"id":"tdp","value":0.48,"unit":"in","pm":0.01,"stated":".49 -.02","source":{"type":"standard","doc":"US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p176","via":"user"}}],"note":"On Windham's part the two grooves' rear walls are 0.257 apart; these callouts make it .26."},"flats_across":{"label":"Wrench flats, across (two, on the rear section)","kind":"length","measurements":[{"id":"tdp","value":0.74,"unit":"in","pm":0.01,"stated":".75 -.02 (rear end view)","source":{"type":"standard","doc":"US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p176","via":"user"}}],"note":"Dimensioned on the rear end view between two chords, left and right. That they run from the rear face to the first groove is read from the side view, where their edges show as two lines 0.22 in either side of the axis over that length (a .75 chord of a .864 circle is 0.21 from the centre)."},"rear_chamfer":{"label":"Rear face's edge, chamfer","kind":"length","measurements":[{"id":"tdp","value":0.03,"unit":"in","pm":0.01,"stated":".02 +.02 X 45°, 2 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p176","via":"user"}}]},"front_chamfer":{"label":"Front face's edge, chamfer","kind":"length","measurements":[{"id":"tdp","value":0.04,"unit":"in","pm":0.01,"stated":".03 +.02 X 45°","source":{"type":"standard","doc":"US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p176","via":"user"}}]},"slots":{"label":"Slots","kind":"count","measurements":[{"id":"tdp","value":5,"unit":"count","stated":"5 SLOTS","source":{"type":"standard","doc":"US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p176","via":"user"}}]},"slot_spacing":{"label":"Slots, angle between neighbours","kind":"angle","measurements":[{"id":"tdp","value":45,"unit":"deg","stated":"45° (basic), 4 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p176","via":"user"}}],"note":"The front end view shows them at the top, 45° and 90° either side of it; nothing in the lower half."},"slot_cutter_r":{"label":"Slots, radius of the cut along the body","kind":"length","measurements":[{"id":"tdp","value":0.5,"unit":"in","pm":0.01,"stated":".49 +.02 R, 5 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p176","via":"user"}}]},"slot_cutter_offset":{"label":"Slots, centre of the cut's radius from the axis","kind":"length","measurements":[{"id":"tdp","value":0.61,"unit":"in","pm":0.005,"stated":".610 ± .005, 5 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p176","via":"user"}}]},"slot_center_from_front":{"label":"Slots, centre of the cut's radius behind the front face","kind":"length","measurements":[{"id":"tdp","value":0.59,"unit":"in","pm":0.005,"stated":".590 ± .005, 5 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p176","via":"user"}}]},"slot_width":{"label":"Slots, width","kind":"length","measurements":[{"id":"tdp","value":0.185,"unit":"in","pm":0.01,"stated":".175 +.020, 5 PLACES (Section B-B)","source":{"type":"standard","doc":"US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p176","via":"user"}}],"note":"Section B-B gives two widths and an angle: .175, .08 and 28°. Read as a cutter .175 thick whose rim narrows at 28° included to a .08 flat: that is the only arrangement in which the three agree (.175 less .08 is twice 0.19 × tan 14°), and it is the shape the side view draws face-on: a slot .08 wide at its ends that opens to full width along its middle. The drawing doesn't say it in words."},"slot_tip_width":{"label":"Slots, width at the cut's deepest edge","kind":"length","measurements":[{"id":"tdp","value":0.09,"unit":"in","pm":0.01,"stated":".08 +.02, 5 PLACES (Section B-B)","source":{"type":"standard","doc":"US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p176","via":"user"}}]},"slot_flank_angle":{"label":"Slots, included angle between the walls near the cut's deepest edge","kind":"angle","measurements":[{"id":"tdp","value":30,"unit":"deg","pm":2,"stated":"28° +4°, 5 PLACES (Section B-B)","source":{"type":"standard","doc":"US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p176","via":"user"}}]},"chamber_d":{"label":"Bore through the slotted body and the front face","kind":"length","measurements":[{"id":"tdp","value":0.67,"unit":"in","pm":0.01,"stated":".66 +.02 Ø (Section A-A)","source":{"type":"standard","doc":"US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p176","via":"user"}}]},"chamber_from_front":{"label":"That bore's depth from the front face","kind":"length","measurements":[{"id":"tdp","value":0.88,"unit":"in","pm":0.01,"stated":".87 +.02 (Section A-A)","source":{"type":"standard","doc":"US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p176","via":"user"}}],"note":"Section A-A: from the front face back to where the 94° cone meets the bore."},"chamber_cone_angle":{"label":"Cone behind that bore, included angle","kind":"angle","measurements":[{"id":"tdp","value":90,"unit":"deg","pm":4,"stated":"94° -8° (Section A-A)","source":{"type":"standard","doc":"US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p176","via":"user"}}]},"exit_bore_d":{"label":"Hole between the thread and the cone","kind":"length","measurements":[{"id":"tdp","value":0.343,"unit":"in","pm":0.005,"stated":".338 +.010 (Section A-A)","source":{"type":"standard","doc":"US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p176","via":"user"}}]},"thread_depth":{"label":"Threaded bore's depth from the rear face","kind":"length","measurements":[{"id":"tdp","value":0.69,"unit":"in","pm":0.01,"stated":".68 +.02 (Section A-A)","source":{"type":"standard","doc":"US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p176","via":"user"}}],"note":"The thread is .500-28 UNEF-2B MOD with .62 MIN FULL THREAD: it takes the AR-length muzzle thread. A barrel's thread longer than this would bottom before the spacer is clamped."},"spacer_od":{"label":"Spacer, outside diameter","kind":"length","measurements":[{"id":"tdp","value":0.74,"unit":"in","pm":0.01,"stated":".75 -.02 Ø","source":{"type":"standard","doc":"US Army TDP drawing 9349052 (Spacer, Compensator), sheet 1 of 1, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p148","via":"user"}}]},"spacer_id":{"label":"Spacer, inside diameter","kind":"length","measurements":[{"id":"tdp","value":0.515,"unit":"in","pm":0.005,"stated":".510 +.010 Ø (datum A)","source":{"type":"standard","doc":"US Army TDP drawing 9349052 (Spacer, Compensator), sheet 1 of 1, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p148","via":"user"}}]},"spacer_thickness_supplied":{"label":"Spacer, thickness as supplied (solid stock and all its laminations)","kind":"length","measurements":[{"id":"tdp","value":0.0705,"unit":"in","pm":0.0045,"stated":".075 -.009","source":{"type":"standard","doc":"US Army TDP drawing 9349052 (Spacer, Compensator), sheet 1 of 1, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p148","via":"user"}}]},"spacer_thickness_solid":{"label":"Spacer, thickness of its solid stock (every lamination peeled)","kind":"length","measurements":[{"id":"tdp","value":0.0325,"unit":"in","pm":0.0025,"stated":"035 -.005 SOLID STOCK; 16-18 LAMINATIONS (.002) THICK","source":{"type":"standard","doc":"US Army TDP drawing 9349052 (Spacer, Compensator), sheet 1 of 1, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p148","via":"user"}}],"note":"The scan shows no decimal point before the 035. It is .035: 16 to 18 laminations of .002 on .030 to .035 make .062 to .071, against the .066 to .075 given for the whole."},"spacer_thickness":{"label":"Spacer, thickness installed","kind":"length","measurements":[{"id":"range","value":0.0525,"unit":"in","pm":0.0225,"source":{"type":"derived","basis":"Between spacer_thickness_solid at its least (.030) and spacer_thickness_supplied at its most (.075): the midpoint, ± half the range.","via":"user"}}],"note":"Laminations are peeled until the compensator tightens with its closed side down, so the installed thickness is whatever that barrel's thread needs: anywhere from the solid stock to the full stack. The value is the middle of that range and the ± covers all of it."},"length":{"label":"Length ahead of the barrel's shoulder, installed (to the front face; the spacer's thickness included)","kind":"length","measurements":[{"id":"stack","value":1.8025,"unit":"in","source":{"type":"derived","expr":"{.spacer_thickness} + {.compensator_length}","via":"user"},"note":"The spacer against the shoulder, the compensator against the spacer."}]},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"spikes","value":2.2,"unit":"oz","stated":"Weight: 2.2oz","source":{"type":"spec","publisher":"manufacturer","name":"Spike's Tactical (its A2 flash hider, 1/2x28, \"Mil-Spec Heavy Phosphate Finish\")","url":"https://www.spikestactical.com/collections/muzzle-devices/flash-hider-a2/","retrieved":"2026-10-01","via":"harvest"}},{"id":"faxon","value":2.25,"unit":"oz","stated":"Weight: 2.25oz","source":{"type":"spec","publisher":"manufacturer","name":"Faxon Firearms (its 5.56 A2 flash hider, 1/2-28, nitride)","url":"https://faxonfirearms.com/5-56-a2-flash-hider-1-2-28-threaded/","retrieved":"2026-10-01","via":"harvest"}},{"id":"kak","value":1.92,"unit":"oz","stated":"Weight- 1.92oz","source":{"type":"spec","publisher":"manufacturer","name":"KAK Industry (its A2 birdcage flash hider, \"Phosphate Coated\")","url":"https://kakindustry.com/a2-birdcage-flash-hider","retrieved":"2026-10-01","via":"harvest"}},{"id":"wing-aero","value":1.9,"unit":"oz","stated":"Weight: 1.9 oz.","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical (Aero Precision's A2 birdcage flash hider, \"Mil-Spec Heavy Phosphate\")","url":"https://www.wingtactical.com/firearm-parts/ar-15/muzzle-devices/aero-precision-a2-birdcage-flash-hider-5-56-223/","retrieved":"2026-10-01","via":"harvest"}},{"id":"wing-spikes","value":2.1,"unit":"oz","stated":"Weight: 2.1 oz.","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical (Spike's Tactical's A2 flash hider)","url":"https://www.wingtactical.com/firearm-parts/ar-15/muzzle-devices/spikes-tactical-a2-flash-hider-5-56-223/","retrieved":"2026-10-01","via":"harvest"}},{"id":"ballistic-barn","value":2.1,"unit":"oz","stated":"Weight- 2.1 oz","source":{"type":"spec","publisher":"retailer","name":"Ballistic Barn (an A2 birdcage flash hider, maker not named)","url":"https://ballisticbarn.com/products/a2-birdcage-flash-hider-1-2x28-threads-5-56-223-ar-15.html","retrieved":"2026-10-01","via":"harvest"}}],"adopt":{"value":2.1,"unit":"oz","pm":0.2,"reason":"Six makers' and retailers' figures for A2s span 1.9 to 2.25 oz: the middle of what they state, ± the spread. Each wording was read on the harvested page."},"note":"Not on the drawing (its UNIT WT. box is empty). Makers of A2s state between 1.9 and 2.25 oz for theirs; steels and finishes differ (Faxon's is nitrided, the others phosphated), and a retailer gives Spike's 0.1 oz less than Spike's does. The catalog part is the drawing's, not one maker's."}}},{"subject":"aero-556-16-mid-barrel","title":"Aero Precision 16 in 5.56 CMV barrel, mid-length (APBA100060C)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"aero","value":32,"unit":"oz","pm":0.5,"stated":"Weight(s) 32oz","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, 16\" 5.56 CMV Barrel, Mid-Length (APBA100060C), Specifications","url":"https://www.aeroprecisionusa.com/556-16-mid-cmv-barrel","retrieved":"2026-10-02","via":"harvest"}}]},"length":{"label":"Barrel length as its maker states it","kind":"length","measurements":[{"id":"aero","value":16,"unit":"in","pm":0.1,"stated":"Barrel Length 16\"","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, 16\" 5.56 CMV Barrel, Mid-Length (APBA100060C), Specifications","url":"https://www.aeroprecisionusa.com/556-16-mid-cmv-barrel","retrieved":"2026-10-02","via":"harvest"}}],"note":"The nominal length (by convention from the bolt's face to the muzzle); Aero's page doesn't say between which points."},"shoulder_x":{"label":"The muzzle shoulder ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":14.89,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/aero-556-16-mid-barrel 63b167b2dab1 (Aero's gallery: the barrel from the side, straight on, the muzzle at the right, 1000 x 630)","scaleRef":"its two end faces, 915.6 px apart (columns 43.2 and 958.8, each behind its rim's arc: tools/trace.py, end_face, the edge at grey 235), as overall_length (16.501: the published 16 from the breech face plus the extension behind it): 55.49 px/in","method":"the flange's rear face (column 97.5: its flat top begins at 98.0 and its rear corner's arc fills column 97), which seats on the receiver's front face, to the shoulder's face (column 924.0: the last column at the full diameter is 923, and the corner's arc ends by 925). The ± is a pixel at each face (0.03) and the published length's own ± (0.05 in 16.5)","via":"harvest"}},{"id":"upper-photo","value":14.95,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/aero-m4e1-complete-upper-16-mid-r-one-15 0a6c8a661544 (Aero's gallery: its complete upper with this barrel under the 15 in R-ONE handguard, from the right, an A2 flash hider on the muzzle, 1000 x 630)","scaleRef":"its top rail's teeth (std.picatinny.slot_pitch), whose pitch shortens toward the muzzle: 14.592 px over the receiver (columns 110 to 320), 14.496 px over columns 330 to 600, 14.376 px over 600 to 870: 37.04, 36.79 and 36.49 px/in (.cache/batch123/bca-556-16-mid-barrel/aero_upper_rail.py); the pivot and takedown lug holes, 236.08 px apart, give the same 37.03 at the receiver","method":"the receiver's front face (column 338.97: .661 ahead of the pivot lug's hole, drawing 8448524) to where the flash hider's washer begins on the bare barrel ahead of the handguard (column 886.8, read on an 8x crop): 261.0 px at 36.79, then 286.8 px at 36.49","via":"harvest"},"note":"Another photo at two thirds of the resolution, another scale, a handguard and a muzzle device over the barrel: the ± is a pixel at each end and 0.3% of scale."}],"adopt":{"from":"photo","reason":"The barrel's own photo, bare, at one and a half times the resolution; Aero's photo of the complete upper puts the shoulder 0.06 further out, inside the two readings' ±."},"note":"Where the thread begins and a muzzle device seats, from the flange's rear face. 14.83 until 2026-10-05: the photo's ends were then the silhouette's tips, 918 px apart (the rear one is its rim's near side, 2 px behind the face), the flange's face a pixel early, and the extension 0.46 behind the breech. The second reading is the check another session's note asked for (docs/STATUS.md had this barrel 'probably about 0.15 in short' by it): Aero's photo of its complete upper with this barrel, where the washer under the flash hider begins, by the rail's own teeth. The same photo has the flash hider's front face 16.81 ahead of the receiver, 1.86 ahead of that shoulder: the A2's 1.75 and 0.11 of crush washer. The catalog's A2 carries the Army's peel spacer at 0.0525 (a2-flash-hider.length), so the app's build ends 0.12 in short of that photo's: 0.06 the two shoulders' difference, 0.06 the washer's kind."},"thread_major_d":{"label":"The muzzle thread's major diameter (its crests)","kind":"length","measurements":[{"id":"tdp","value":0.4957,"unit":"in","pm":0.0033,"stated":"1/2-28 UNEF-2A MAJOR DIA .4989/.4924","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213","via":"user"},"note":"The middle of the two limits, ± half their spread."}],"note":"The Army barrel's 1/2-28 thread, for the 1/2-28 Aero states: what the barrel's thread is drawn at since 2026-10-06 (its silhouette until then). Not a measurement of this barrel: the photo's silhouette of the thread, a pixel 0.018 in across, is the check, and it reads between the roots and the crests."},"thread_minor_d":{"label":"The muzzle thread's minor diameter (its roots)","kind":"length","measurements":[{"id":"tdp","value":0.4551,"unit":"in","pm":0.002,"stated":"MINOR DIA .4551 MAX","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213","via":"user"},"note":"A maximum: the ± is mine, as bcm-16-mid-barrel.thread_minor_d has it."}]},"thread_pitch":{"label":"The muzzle thread's pitch","kind":"length","measurements":[{"id":"tdp","value":0.03571,"unit":"in","pm":0.00005,"stated":"1/2-28 UNEF-2A","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213","via":"user"}},{"id":"aero","value":0.03571,"unit":"in","pm":0.00005,"stated":"Thread Pitch 1/2-28 Threaded","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, 16\" 5.56 CMV Barrel, Mid-Length (APBA100060C), Specifications","url":"https://www.aeroprecisionusa.com/556-16-mid-cmv-barrel","retrieved":"2026-10-02","via":"harvest"}}],"adopt":{"from":"aero","reason":"The maker's statement for this barrel; the Army's drawing has the same thread on its own."},"note":"28 threads to the inch, by Aero's statement and the Army barrel's drawing: neither is a measurement of this barrel, and its photo doesn't resolve the thread (a pitch is two pixels)."},"bore_d":{"label":"The bore's diameter (across the lands)","kind":"length","measurements":[{"id":"tdp","value":0.2195,"unit":"in","pm":0.0005,"stated":".219 DIA +.001","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 2 of 2, rev J: Section U-U, rifling detail at 10/1; user-supplied scan, PDF page 211","via":"user"},"note":"The middle of the limits, ± half their spread."}],"note":"The cartridge's, for the hole the barrel is drawn with (2026-10-06): Aero states \"Caliber 5.56 NATO\" and no bore, so this is the Army barrel's for that cartridge and not a measurement of this one. The grooves (.2235 +.0010 on the same detail) aren't drawn."},"thread_length":{"label":"The muzzle thread's length","kind":"length","measurements":[{"id":"photo","value":0.63,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-556-16-mid-barrel 63b167b2dab1 (Aero's gallery: the barrel from the side, straight on, the muzzle at the right, 1000 x 630)","scaleRef":"its two end faces, 915.6 px apart (columns 43.2 and 958.8, each behind its rim's arc: tools/trace.py, end_face, the edge at grey 235), as overall_length (16.501: the published 16 from the breech face plus the extension behind it): 55.49 px/in","method":"the shoulder's face (column 924.0) to the muzzle's face (column 958.8): 34.8 px","via":"harvest"}}],"note":"The Army's M16 barrel has .63 from the shoulder to the muzzle (8448549 sheet 2); a mid-length chart in the TDP folder 0.624. Read 0.59 until 2026-10-05, from the shoulder to two columns short of the silhouette's end; the muzzle's face is a fifth of a pixel inside that end by its rim's arc."},"gas_port_x":{"label":"The gas port ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":9.17,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/aero-556-16-mid-barrel 63b167b2dab1 (Aero's gallery: the barrel from the side, straight on, the muzzle at the right, 1000 x 630)","scaleRef":"its two end faces, 915.6 px apart (columns 43.2 and 958.8, each behind its rim's arc: tools/trace.py, end_face, the edge at grey 235), as overall_length (16.501: the published 16 from the breech face plus the extension behind it): 55.49 px/in","method":"the flange's rear face (column 97.5), which seats on the receiver's front face, to the journal's rear end, where the ring behind it (0.837 in across) ends (column 590.0: the silhouette steps down between columns 589 and 590): 8.874; plus 0.300 to the port","via":"harvest"}}],"note":"Aero says \"Gas System Length Mid-Length\" and gives no distance. Taken as the journal's rear end in the photo plus the 0.300 in a mid-length barrel's chart puts the port ahead of it (references' AR-15_M4_Barrel_Dimensions.jpg: a third-party illustration, not an Army drawing). Checks: the port itself is in the photo (the barrel is turned so that it faces the lens), a dot three pixels across with its middle at column 606.5, 0.297 ahead of the journal's rear end (the Army's 8448548 has .295 on the rifle's barrel) and 9.17 ahead of the flange's face; the same chart puts the port 9.670 ahead of the barrel's breech end, which is 0.489 behind this face on the reference CAD set's extension (the .620 tenon less the 0.131 flange): 9.18; the catalog's two other mid-length barrels read 9.13 and 9.14 by their own photos; and Shooting Sports USA (NRA) has a mid-length port 2 in ahead of a carbine's, from the upper receiver's face, the pistol port 4 in and the carbine 3 more: 9."},"journal_od":{"label":"The gas block journal's diameter","kind":"length","measurements":[{"id":"aero","value":0.75,"unit":"in","pm":0.001,"stated":"Gas Block Journal .750\"","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, 16\" 5.56 CMV Barrel, Mid-Length (APBA100060C), Specifications","url":"https://www.aeroprecisionusa.com/556-16-mid-cmv-barrel","retrieved":"2026-10-02","via":"harvest"}}]},"muzzle_od":{"label":"The diameter behind the muzzle thread","kind":"length","measurements":[{"id":"photo","value":0.7,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-556-16-mid-barrel 63b167b2dab1 (Aero's gallery: the barrel from the side, straight on, the muzzle at the right, 1000 x 630)","scaleRef":"its gas block journal's diameter, 40.7 px, as the published .750 (journal_od): 54.2 px/in (tools/turned.py; a turned part's silhouette is true along its length at a diameter's scale)","method":"the section behind the thread (px 883 to 923): ratio 0.933 to the journal","via":"harvest"}}],"note":"Read with the edge at grey 235 it is the same: 38.79 px against the journal's 41.76, 0.697."},"overall_length":{"label":"End to end, the extension's rear face to the muzzle's face","kind":"length","measurements":[{"id":"photo","value":16.44,"unit":"in","pm":0.1,"source":{"type":"photo","photo":"references/aero-556-16-mid-barrel 63b167b2dab1 (Aero's gallery: the barrel from the side, straight on, the muzzle at the right, 1000 x 630)","scaleRef":"its gas block journal's diameter, 41.76 px between its edges at grey 235 (the mean over columns 592 to 690), as the published .750 (journal_od): 55.68 px/in; the ± is a quarter pixel of that width","method":"its two end faces, each behind its rim's arc (tools/trace.py, end_face): columns 43.2 and 958.8, 915.6 px","via":"harvest"}},{"id":"published","value":16.501,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{.length} + {.extension_behind_breech}","via":"harvest"}}],"adopt":{"from":"published","reason":"Lengths at the published length's scale, which the journal's agrees with to 0.3%. At it the extension reads 0.98 behind its flange (the reference CAD set's 0.990), the thread 0.63 (the Army's .63) and the gas port 9.17 from the receiver's face (a mid-length chart's 9.18)."},"note":"The published length is the scale for lengths, and the journal's scale agrees with it: with the edge read at grey 235 the journal is 41.76 px across and the end faces 915.6 px apart, 16.44 in, 0.3% under. Until 2026-10-05 the photo stood here at 16.93: the silhouette's tips, 918 px apart, at the 54.2 px/in tools/turned.py read off the journal at mid-grey, where a dark tube with a light limb reads thin; that made the photo look 2.8% longer than the published length, and the note here said a black tube reads thin on white. It does at mid-grey, not at 235 (Bear Creek's barrel, the same)."},"extension_behind_breech":{"label":"The barrel extension's rear end behind the barrel's breech end","kind":"length","measurements":[{"id":"tdp","value":0.46,"unit":"in","pm":0.04,"stated":"extension about 1.08 long (scaled); tenon .620 ±.001","source":{"type":"standard","doc":"US Army TDP drawing 8448548 (Barrel and Barrel Extension Assembly), PDF page 212, top view at 1/1 (scaled: the extension's own drawing 8448550 isn't in the package); and 8448549 sheet 1 (the barrel's .620 tenon)"},"note":"The extension's length less the barrel's tenon: 1.08 - .620."},{"id":"model","value":0.501,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{std.ar15.barrel_extension_behind_breech}","via":"harvest"},"note":"The reference CAD set's Barrel_Extension.step, 1.121 from its front face to its rear end, less the .620 tenon: the readings and their sources are in the standard's ledger (std.ar15.barrel_extension_length, std.ar15.barrel_tenon_length)."}],"adopt":{"from":"model","reason":"The CAD set's extension is read face by face, the drawing's view is scaled and isn't to one scale; the two agree within the scaled one's ±. And one figure for every barrel on this extension: BCM's and Bear Creek's use the same."},"note":"One extension for the catalog's three 5.56 barrels (2026-10-05): each took its 16 in from a breech placed by its own reading of the extension (0.46 here, 0.501, 0.57), and their muzzles stood 0.11 in apart. The extension's length less the barrel's tenon, which threads into it from its front face (8448549 sheet 1: .620 ± .001). The extension's own drawing (8448550) isn't in the package, so its length is the reference CAD set's, read for BCM's barrel; the reading scaled off the assembly drawing's 1/1 view, which stood here alone, is 0.04 less and stays beside it (that view's own callouts put its scale anywhere within 8%). This barrel's photo agrees with the CAD's extension where it can: 0.98 from its rear face to the flange's rear face (0.990), a flange about 0.12 between its corners (0.131), 0.997 across at the journal's scale (.9987). The bolt face sits behind the breech end (8448548 Section A-A: the bolt's lugs fill the .283 between the extension's locking face and the breech face); the published 16 is taken from the breech end, as the other two barrels take theirs."},"flange_od":{"label":"The barrel extension's flange, its diameter","kind":"length","measurements":[{"id":"photo","value":1.173,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/aero-556-16-mid-barrel 63b167b2dab1 (Aero's gallery: the barrel from the side, straight on, the muzzle at the right, 1000 x 630)","scaleRef":"its gas block journal's diameter as the published .750 (tools/turned.py: ratio 1.564)","method":"the silhouette's widest, px 97 to 104","via":"harvest"}}],"note":"The traced outline's scale reference (the silhouette's greatest height). With the edge at grey 235 the flange is 65.49 px against the journal's 41.76: 1.176. The reference CAD set's is 1.170."},"extension_rear_x":{"label":"The barrel extension's rear face, from the flange's rear face (negative: inside the receiver)","kind":"length","measurements":[{"id":"photo","value":-0.979,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-556-16-mid-barrel 63b167b2dab1 (Aero's gallery: the barrel from the side, straight on, the muzzle at the right, 1000 x 630)","scaleRef":"its two end faces, 915.6 px apart (columns 43.2 and 958.8, each behind its rim's arc: tools/trace.py, end_face, the edge at grey 235), as overall_length (16.501: the published 16 from the breech face plus the extension behind it): 55.49 px/in","method":"the extension's rear face (column 43.2, behind its rim's arc: the silhouette's tip, the rim's near side, is at 40.8) to the flange's rear face (column 97.5), which seats on the receiver's front face","via":"harvest"}}],"note":"The reference CAD set's extension has 0.990 here (1.121 less its 0.131 flange); BCM's barrel reads 0.984 by its own photo. -1.004 until 2026-10-05, from the silhouette's tip."},"outline_rear_face":{"label":"The extension's rear face in the traced outline's own frame (from the silhouette's rear tip, at the journal's scale)","kind":"length","measurements":[{"id":"photo","value":0.058,"unit":"in","pm":0.028,"source":{"type":"photo","photo":"references/aero-556-16-mid-barrel 63b167b2dab1 (Aero's gallery: the 16 in 5.56 CMV mid-length barrel from the side, 1000 x 630)","scaleRef":"scale from aero-556-16-mid-barrel.flange_od = 1.173 in (y-extent 65 px → 55.4 px/in)","method":"the min end's face: the silhouette's tip at 0.014 less its rim's arc, 0.044 in of sag at radius 0.496269 (the end is seen from 5.1° off square; arc fitted over 118 rows, rms 0.005) of the traced outline (tools/trace.py); the extension's rear face in the outline's own frame (from its rear tip, at the journal's scale)","via":"harvest"}}],"note":"Where the outline is cut: the silhouette's tip is the rear rim's near side, which stands behind the face by the rim's arc."},"outline_front_face":{"label":"The muzzle's face in the traced outline's own frame (from the silhouette's rear tip, at the journal's scale)","kind":"length","measurements":[{"id":"photo","value":16.581,"unit":"in","pm":0.849,"source":{"type":"photo","photo":"references/aero-556-16-mid-barrel 63b167b2dab1 (Aero's gallery: the 16 in 5.56 CMV mid-length barrel from the side, 1000 x 630)","scaleRef":"scale from aero-556-16-mid-barrel.flange_od = 1.173 in (y-extent 65 px → 55.4 px/in)","method":"the max end's face: the silhouette's tip at 16.585 less its rim's arc, 0.004 in of sag at radius 0.225577 (the end is seen from 0.9° off square; arc fitted over 120 rows, rms 0.001) of the traced outline (tools/trace.py); the muzzle's face in the outline's own frame (from its rear tip, at the journal's scale)","via":"harvest"}}],"note":"Where the outline is cut. The fit finds almost no arc at this end (the thread's lead chamfer takes the rim's place), so the face is a fifth of a pixel inside the silhouette's end."}}},{"subject":"aero-556-bcg","title":"Aero Precision 5.56 bolt carrier group, complete, black nitride (APRH100615C)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"aero","value":11.52,"unit":"oz","pm":0.005,"stated":"Weight(s) 11.52 oz","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, 5.56 Bolt Carrier Group, Complete - Black Nitride (APRH100615C), Specifications","url":"https://www.aeroprecisionusa.com/ar15-556-bolt-carrier-group-complete-black-nitride","retrieved":"2026-10-02","via":"harvest"}}]},"length":{"label":"The carrier's length","kind":"length","measurements":[{"id":"std","value":6.672,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.ar15.carrier_length}","via":"harvest"},"note":"US Army TDP drawing 8448507 (Carrier, Bolt): the tail's rear face to the front (bolt) face. Read here first, for this part (2026-10-02); the standard's ledger has it since the carriers were modelled."}],"note":"The carrier is the standard's: Aero's page has \"M16-cut carrier\" and \"Carrier has forward assist serrations\", and states no size."},"od":{"label":"The carrier's diameter","kind":"length","measurements":[{"id":"std","value":0.994,"unit":"in","pm":0.0005,"source":{"type":"derived","expr":"{std.ar15.carrier_rail_od}","via":"harvest"},"note":"The diameter its rails are ground to (8448507: .9945 -.0010, grind after heat treat); the body and the tail are .930 (std.ar15.carrier_body_od). Until 2026-10-05 this note called it the ground body."}],"note":"The carrier is the standard's: Aero's page has \"M16-cut carrier\", and states no size."}}},{"subject":"aero-750-gas-block","title":"Aero Precision .750 low profile gas block (APRH101205C)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"aero","value":1.6,"unit":"oz","pm":0.05,"stated":"Weight(s) 1.6 oz","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, .750 Low Profile Gas Block w/ Aero Logo - Nitride (APRH101205C), Specifications","url":"https://www.aeroprecisionusa.com/750-low-profile-gas-block-w-aero-logo-nitride","retrieved":"2026-10-02","via":"harvest"}}]},"journal_id":{"label":"The journal it is bored for","kind":"length","measurements":[{"id":"aero","value":0.75,"unit":"in","pm":0.001,"stated":"Fits barrels with .750 Outer Diameter","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, .750 Low Profile Gas Block w/ Aero Logo - Nitride (APRH101205C), Features","url":"https://www.aeroprecisionusa.com/750-low-profile-gas-block-w-aero-logo-nitride","retrieved":"2026-10-02","via":"harvest"}}]},"length":{"label":"Length along the barrel","kind":"length","measurements":[{"id":"photo","value":0.93,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-750-gas-block a20acc7a2f17 (Aero's gallery: the block from the side, 1000 x 631)","scaleRef":"the side view's height, 543 px, as the end view's (the boss's top to the ring's bottom: 1.232 in by its bore)","method":"the side view's width, 410 px","via":"harvest"}},{"id":"photo-tab","value":1.034,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-750-gas-block a20acc7a2f17 (Aero's gallery: the block from the side, 1000 x 631)","scaleRef":"the side view's height, 545 px, as the end view's from the boss's top to the set-screw tab's bottom (0.795 + 0.572 = 1.367 in by its bore): 398.6 px/in","method":"the side view's width, 412 px (.cache/research/aero-upper/gb.py)","via":"harvest"},"note":"The side's bottom edge is the tab's, which runs the block's whole length (the oblique photo ffbee1a0d42b shows its flat bottom edge along the side to the front face): the 0.93 took the ring's bottom for it (2026-10-03)."},{"id":"photo-boss","value":1.013,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/aero-750-gas-block a20acc7a2f17 (Aero's gallery: the block's right side, the front face at the right, 1000 x 631) and d829fa7f05e0 (its left side, the front face at the left, 1000 x 631)","scaleRef":"each side view's height on its level stretch (539.0 px, rows 47.0 to 586.0; 529.7 px, rows 50.9 to 580.5) as the end view's from the boss's top to the tab's flat, 1.355 in by its bore (rows 48.4 to 587.3 over a rim 298.2 px across): 397.8 and 390.9 px/in","method":"the two end faces in the boss's rows (rows 106 to 166, where the roll pin's hole is), each at the 50% level: columns 311.7 to 715.0 (403.3 px, 1.014 in) and 319.2 to 714.9 (395.7 px, 1.012 in)","via":"harvest"},"note":"The boss is the narrow part (0.33 in across, on the block's middle plane): its two faces are the block's own. In the ring's rows, 0.88 in across, the same two faces read 5 to 7 px further apart in each photo (409 and 408 px: 1.03 to 1.04 in), which is the ring's near and far edges seen a few degrees off square and from close by; the 1.034 above is that reading. A whole inch (what two sellers say of BCM's block) is just outside this ±."}],"adopt":{"from":"photo-boss","reason":"Read where the block is narrowest across the rifle, in two photos that agree within 0.002 in; the 1.034 is the same two faces read across the ring, which a view a few degrees off square widens (2026-10-13). The 0.93 took the ring's bottom for the tab's."},"note":"Not published. Read off the side view against the end view's height (the block's top to its bottom, the same in both)."},"height_above_bore":{"label":"How high its top stands above the bore","kind":"length","measurements":[{"id":"photo","value":0.79,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aero-750-gas-block 3f97b27af899 (Aero's gallery: the block end-on, the tube's boss up, 1000 x 631)","scaleRef":"its bore, 297 px across (x 360-658, y 213-509), as the .750 journal it is bored for (journal_id): 396 px/in, in the bore's near face","method":"the boss's top (row 48) to the bore's centre (row 361): 313 px","via":"harvest"}}],"note":"Not published. The top of the gas tube's boss."},"port_from_rear":{"label":"Its gas port ahead of its rear face","kind":"length","measurements":[{"id":"derived","value":0.269,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-750-gas-block.length} - {aero-750-gas-block.pin_hole_from_front} - {aero-750-gas-block.pin_to_port}"},"note":"The pin's hole is 0.687 ahead of the rear face in both side views (the Army's sight: .688), read directly; the ± is that reading's and the drawing's."},{"id":"chart","value":0.3,"unit":"in","pm":0.03,"stated":"0.300 (the 0.075 port ahead of the 0.750 journal's rear end)","source":{"type":"spec","publisher":"unknown","name":"AR-15_M4_Barrel_Dimensions.jpg in the user's TDP folder (Spec_Sheets): a third-party illustration of a 14.5 in mid-length barrel, no drawing number; its 0.620 tenon and 0.980 collar match the Army's 8448549"},"note":"The barrel's own figure, taken until 2026-10-13 as the block's with its rear face against the shoulder. It put the tube's pin hole 0.03 in behind the block's cross hole."}],"adopt":{"from":"derived","reason":"The block's own, by its pin hole in two photos: the tube's pin goes through the block's cross hole, and its gas hole is then here. The chart's figure is the barrel's, with the block hard against the shoulder."},"note":"Not published. Where the standard tube's gas hole lands when its pin is in the block's cross hole: the block's length less the pin's place behind the front face less the tube's pin-to-port. The Army's own sight has its port .270 from its rear face (8448566; the callout is in BCM's block's ledger, port_from_rear). The barrel's port is 0.300 ahead of its journal's shoulder (the chart below), so the block's rear face stands three hundredths ahead of the shoulder; the discovery report quotes Aero's support for the same (\"Your gas block will sit approximately .025” off of the shoulder\", data/proposals/discovery/aero-556-upper.yaml: a sentence read there and not on a harvested copy, so no reading here)."},"tab_below_bore":{"label":"The set screws' flat below the bore axis","kind":"length","measurements":[{"id":"photo","value":0.568,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/aero-750-gas-block 3f97b27af899 (Aero's gallery: the block end-on, the tube's boss up, 1000 x 631)","scaleRef":"its bore's rim as a circle through 310 rays (the 50 degrees about the set screw's tip left out): centre row 361.3, 297.7 px across at the 165 level and 298.8 at 128 (rms 0.3 and 0.6 px), 298.2 taken as the .750 journal it is bored for (journal_id): 397.6 px/in","method":"the flat's edge at the 50% level, row 587.2 to 587.4 across its middle 0.15 in: 226.0 px below the bore's centre. The boss's top, row 48.4 on the axis, is 312.9 px above it: 0.787, which height_above_bore (0.79) has","via":"harvest"}}],"note":"Not published. The flat underside of the tab the set screws go up through. The traced outline (profiles.front) has it at 0.576: its frame is the bore as one circle through every ray, the set screw's tip in the bore's floor among them, which puts the centre 1.6 px high and the rim 1.6 px small."},"pin_hole_from_front":{"label":"The roll pin's cross hole behind the front (logo) face","kind":"length","measurements":[{"id":"photo","value":0.326,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/aero-750-gas-block a20acc7a2f17 (Aero's gallery: the block's right side, the front face at the right, 1000 x 631) and d829fa7f05e0 (its left side, 1000 x 631)","scaleRef":"each side view's height as the end view's, 1.355 in by its bore: 397.8 and 390.9 px/in (as length, photo-boss)","method":"the hole's centre (a circle through its 50% edge on 72 rays: column 585.3 and column 446.7) to the front face's edge in the boss's rows (columns 715.0 and 319.2): 129.7 and 127.5 px, 0.326 in both; from the rear face 0.688 and 0.686","via":"harvest"}}],"note":"The logo is on the face nearer the pin's hole (the three-quarter view, ffbee1a0d42b), and the tube's pin is at the tube's front end: the logo face is the muzzle end, and the tube's hole enters from the other."},"pin_hole_d":{"label":"The roll pin's cross hole, diameter","kind":"length","measurements":[{"id":"tdp","value":0.078,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{bcm-750-gas-block.pin_hole_d}","via":"user"},"note":"The Army's drawing 8448566 (Sight, Front), \".078 DIA +.003 THRU\": the hole the gas tube's pin goes through. Its source is in BCM's block's ledger; this block takes the same tube and pin (Aero: \"*Roll pin not included*\")."},{"id":"photo","value":0.079,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/aero-750-gas-block a20acc7a2f17 (Aero's gallery: the block's right side, 1000 x 631) and d829fa7f05e0 (its left side, 1000 x 631)","scaleRef":"each side view's height as the end view's, 1.355 in by its bore: 397.8 and 390.9 px/in","method":"a circle through the hole's 50% edge on 72 rays: 31.7 and 30.3 px across, 0.080 and 0.077 in","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The pin it takes is the Army's; the hole in both photos is that size within a pixel."}},"pin_to_port":{"label":"The gas tube's pin hole to its gas hole","kind":"length","measurements":[{"id":"tdp","value":0.418,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{bcm-750-gas-block.pin_to_port}","via":"user"},"note":"The Army's drawing 8448567 (Gas Tube Assembly), \".418 ±.002\": its source is in BCM's block's ledger. The same figure is std.ar15.gas_tube_hole_from_front (.605 REF) less the pin's .187 from the tube's front end."}]},"tube_hole_d":{"label":"The gas tube's hole, diameter","kind":"length","measurements":[{"id":"tdp","value":0.1805,"unit":"in","pm":0.001,"source":{"type":"derived","expr":"{bcm-750-gas-block.tube_hole_d}","via":"user"},"note":"The Army's drawing 8448566 (Sight, Front), \".1805 DIA +.0010\": its source is in BCM's block's ledger. The Army's sight, not this block."}],"note":"Not published, and no view of the rear face is on file. The Army's sight's hole for the same .180 tube."},"tube_hole_past_pin":{"label":"How far the gas tube's hole runs on ahead of the pin's hole","kind":"length","measurements":[{"id":"tdp","value":0.217,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{bcm-750-gas-block.tube_hole_past_pin}","via":"user"},"note":"The Army's drawing 8448566 (Sight, Front), \".905 ±.015 DEPTH; .688 ±.003\": its source is in BCM's block's ledger. The Army's sight, not this block."}],"note":"Not published. The logo face is closed (3f97b27af899, ffbee1a0d42b): the hole enters from the rear face and ends inside the boss. The Army's sight: the hole .905 deep, the pin .688 from the same face; this block's pin is 0.687 from its rear face, so its hole would end 0.904 in, 0.11 behind the logo."},"edge_break":{"label":"The break along its edges","kind":"length","measurements":[{"id":"photo","value":0.012,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/aero-750-gas-block a20acc7a2f17 (Aero's gallery: the block's right side, 1000 x 631) and d829fa7f05e0 (its left side, 1000 x 631)","scaleRef":"each side view's height as the end view's, 1.355 in by its bore: 397.8 and 390.9 px/in","method":"the boss's top edge where it meets each end face: 2.5 to 4 px low one column pair in from the rear face and 3 to 10 px low at the front face's, level by the third pair (5 px in)","via":"harvest"},"note":"Two to five pixels, and the front's reads the larger in both photos. One size is drawn on every edge."}],"note":"Not published. The front face's rim shows it as a bright line in the three-quarter view (ffbee1a0d42b)."},"set_screw_from_front":{"label":"The set screw that shows, its middle behind the front (logo) face","kind":"length","measurements":[{"id":"photo","value":0.258,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/aero-750-gas-block a20acc7a2f17 (Aero's gallery: the block's right side, the front face at the right, 1000 x 631) and d829fa7f05e0 (its left side, 1000 x 631)","scaleRef":"each side view's height as the end view's, 1.355 in by its bore: 397.8 and 390.9 px/in","method":"the columns over which the bottom edge is more than a pixel below the tab's flat: 582 to 642 in the first (0.679 to 0.830 from the rear face, column 311.7) and 390 to 450 in the second (0.181 to 0.335 from the front face, column 319.2): its middle 0.258 behind the front face in both","via":"harvest"}}],"note":"Aero: \"Set Screws are Steel 10-32 x 3/16 Knurled Cup Point\": two. One stands out of the tab's flat in both side views, 0.011 in proud (4.4 px) over 0.15 in; nothing else breaks the flat's edge, so the other is at the flat or under it and no view on file says where along the block it is. A screw's tip shows inside the bore in the end view (3f97b27af899: 0.12 in wide on the bore's middle, 0.04 in in from the wall); which of the two it is isn't read. No view of the underside is on file."},"set_screw_end_d":{"label":"A set screw's end face, as wide as it shows under the tab","kind":"length","measurements":[{"id":"photo","value":0.15,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/aero-750-gas-block a20acc7a2f17 (Aero's gallery: the block's right side, 1000 x 631) and d829fa7f05e0 (its left side, 1000 x 631)","scaleRef":"each side view's height as the end view's, 1.355 in by its bore: 397.8 and 390.9 px/in","method":"the columns over which the bottom edge is more than a pixel below the tab's flat, read every 4 px: 60 px in each, 0.151 and 0.153 in","via":"harvest"},"note":"Narrower than the thread (set_screw_d): the screw's end is broken, and it is the end that stands out of the tab."}]},"set_screw_d":{"label":"A set screw, its diameter","kind":"length","measurements":[{"id":"superlative","value":0.185,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{superlative-750-gas-block.set_screw_d}","via":"harvest"},"note":"A 10-32 set screw's end as photographed in the flat of Superlative Arms' block (its sellers: \"10-32 x 3/16\"): the reading and its photo are in that block's ledger. Another maker's screw of the thread Aero names."}],"note":"Aero names the thread 10-32 and no view shows a screw's whole width in the tab (its end alone stands out of it: set_screw_end_d). Read on a photo of the same thread's screw, not taken from a thread table."},"set_screw_length":{"label":"A set screw, length","kind":"length","measurements":[{"id":"aero","value":0.1875,"unit":"in","pm":0.0005,"stated":"Set Screws are Steel 10-32 x 3/16 Knurled Cup Point","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, .750 Low Profile Gas Block w/ Aero Logo - Nitride (APRH101205C), Features","url":"https://www.aeroprecisionusa.com/750-low-profile-gas-block-w-aero-logo-nitride","retrieved":"2026-10-02","via":"harvest"}}],"note":"From the journal's surface down, a 3/16 screw ends 0.005 in inside the tab's flat (0.568 less the journal's .375 is 0.193 of thread): at the flat, as on a barrel. In Aero's photos, off a barrel, the one that shows is backed out 0.011 in proud."},"set_screw_key":{"label":"A set screw's hex socket, across flats","kind":"length","measurements":[{"id":"aero-support","value":0.09375,"unit":"in","pm":0.0005,"stated":"Gas Block set screws: 40 in lbs. (3/32 Allen Key) (thread locker will void warranty)","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision support, Torque Specifications, as quoted in data/proposals/discovery/aero-556-upper.yaml and the part's seed (read 2026-10-02 from the Wayback Machine's copy of 2025-08-13)","url":"https://support.aeroprecisionusa.com/hc/en-us/articles/14130432684951-Torque-Specifications","retrieved":"2026-10-02","via":"harvest"}}],"note":"No view on file shows a socket. Aero's support names the key; the sentence is in the part's seed as the discovery report read it (a Wayback copy of 2025-08-13), not on the part's own page and not read again on a harvested copy."},"od":{"label":"Outside diameter of its ring about the barrel","kind":"length","measurements":[{"id":"photo","value":0.884,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/aero-750-gas-block 3f97b27af899 (Aero's gallery: the block end-on, the tube's boss up, 1000 x 631)","scaleRef":"its bore, 297 px across (x 360-658, y 213-509), as the .750 journal it is bored for (journal_id): 396 px/in, in the bore's near face","method":"the ring's width, 350 px (x 335-685)","via":"harvest"}}]},"boss_width":{"label":"Width of the gas tube's boss on top","kind":"length","measurements":[{"id":"photo","value":0.33,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-750-gas-block 3f97b27af899 (Aero's gallery: the block end-on, the tube's boss up, 1000 x 631)","scaleRef":"its bore, 297 px across (x 360-658, y 213-509), as the .750 journal it is bored for (journal_id): 396 px/in, in the bore's near face","method":"the boss's width below its rounded top, 126 to 132 px (rows 100 to 130)","via":"harvest"}}]},"tube_hole_above_bore":{"label":"The gas tube's hole, its axis above the bore (at the block)","kind":"length","measurements":[{"id":"tdp","value":0.625,"unit":"in","pm":0.006,"source":{"type":"derived","expr":"{std.ar15.gas_tube_above_bore} - {aero-mid-gas-tube.bend_offset}","via":"user"},"note":"The receiver's tube hole (8448524 View F-F, .781) less the tube's bend (8448567, .156): the tube drops from the receiver to the block."},{"id":"photo","value":0.625,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-750-gas-block a20acc7a2f17 (Aero's gallery: the block from the side, 1000 x 631)","scaleRef":"398.6 px/in (as length)","method":"the roll pin's hole (the pin crosses the tube's), 0.170 below the block's top (0.795 above the bore)","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawings; Aero's photo agrees."}}}},{"subject":"aero-ar15-front-sight-post-kit","title":"Aero Precision AR15 Front Sight Post Kit (APRH100526C)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"metal","value":0.109,"unit":"oz","pm":0.01,"source":{"type":"derived","expr":"(0.0143 + 3.14159265 * ({.detent_d} * {.detent_d} / 4 * {.detent_length} + {.detent_tip_d} * {.detent_tip_d} / 4 * {.detent_tip_length})) * {std.density.steel}","via":"harvest"},"note":"0.0143 in3 is the post model's own volume, read off its manifest (volume_in3); the test holds the two to each other."},{"id":"kygunco","value":16,"unit":"oz","pm":8,"stated":"Weight 1 lb","source":{"type":"spec","publisher":"retailer","name":"KYGUNCO, AERO PRECISION AR15 Front Sight Post Kit (Item # 229084, RPR-APRH100526C), item details","url":"https://www.kygunco.com/product/aero-precision-aprh100526c-front-sight-post-kit-detent-spring-sight","retrieved":"2026-10-28","via":"harvest"},"note":"A parcel's weight (a shop's whole pound for three small steel pieces): not the kit's."}],"adopt":{"from":"metal","reason":"Its own steel; the seller's pound is what it ships in."},"note":"WORKED OUT, not published: the post's steel (its model's volume, pipeline/blender/aero_ar15_front_sight_post_kit.py: 0.0143 in3) and the detent's (the CAD set's two cylinders: 0.0097 in3), times std.density.steel. The detent's spring isn't counted (no size on file: a few hundredths of an ounce). KYGUNCO's \"Weight 1 lb\" is its parcel's."},"height":{"label":"Height above the tower's top","kind":"length","measurements":[{"id":"derived","value":0.101,"unit":"in","pm":0.025,"source":{"type":"derived","expr":"{.flange_thickness} + {.blade_height} - {.seat_below_tower_top}"}}],"note":"The blade's top above the base's tower top, the post screwed down onto the counterbore's floor. Turned up, it stands higher by a 36th of an inch a turn (its thread): its height on a rifle is set when it is zeroed."},"seat_below_tower_top":{"label":"Its flange's underside below the tower's top (the base's counterbore floor)","kind":"length","measurements":[{"id":"tdp","value":0.227,"unit":"in","pm":0.02,"stated":".227 ±.020","source":{"type":"standard","doc":"US Army TDP drawing 8448566 (Sight, Front), rev H, PDF page 145, the side view's section through the tower: the post's counterbore, from the tower's top to the floor where the thread begins","via":"user"}}],"note":"The post's seat: its flange bottomed in the base's counterbore. The Army's base's figure, which every A2 base made to the drawing has (BCM's F base calls itself \"Milspec\"). Its frame's origin is the tower's top on its axis (the front sight post interface)."},"blade_width":{"label":"The blade, across its flats (it is square)","kind":"length","measurements":[{"id":"tdp","value":0.07,"unit":"in","pm":0.002,"stated":".072 -.004 2 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 9349056 (Post, Front Sight), rev G, PDF page 178, side view: the middle of .068 to .072","via":"user"}}]},"blade_height":{"label":"The blade's top above the flange's top","kind":"length","measurements":[{"id":"tdp","value":0.268,"unit":"in","pm":0.005,"stated":".273 -.010","source":{"type":"standard","doc":"US Army TDP drawing 9349056 (Post, Front Sight), rev G, PDF page 178, side view: the middle of .263 to .273","via":"user"}}]},"flange_d":{"label":"The flange, its diameter","kind":"length","measurements":[{"id":"tdp","value":0.3645,"unit":"in","pm":0.0015,"stated":".366 -.003 Ø","source":{"type":"standard","doc":"US Army TDP drawing 9349056 (Post, Front Sight), rev G, PDF page 178, top view","via":"user"}},{"id":"model","value":0.366,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight_Post.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a front sight post)","method":"its flange, cylinders r 0.183 between its notches","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing; the CAD set's post has its nominal."}},"flange_thickness":{"label":"The flange, its thickness","kind":"length","measurements":[{"id":"tdp","value":0.06,"unit":"in","pm":0.005,"stated":".065 -.010","source":{"type":"standard","doc":"US Army TDP drawing 9349056 (Post, Front Sight), rev G, PDF page 178, side view: the middle of .055 to .065","via":"user"}}]},"notch_r":{"label":"The flange's detent notches, their radius","kind":"length","measurements":[{"id":"tdp","value":0.04675,"unit":"in","pm":0.00125,"stated":".0455 +.0025 R 4 RADII EQUALLY SPACED ON .400 Ø","source":{"type":"standard","doc":"US Army TDP drawing 9349056 (Post, Front Sight), rev G, PDF page 178, top view","via":"user"}}],"note":"Four, equally spaced: the detent holds the post at each quarter turn."},"notch_circle_d":{"label":"The circle the notches' centres are on","kind":"length","measurements":[{"id":"tdp","value":0.4,"unit":"in","pm":0.0005,"stated":".400 Ø (basic)","source":{"type":"standard","doc":"US Army TDP drawing 9349056 (Post, Front Sight), rev G, PDF page 178, top view","via":"user"}}]},"shank_length":{"label":"The threaded shank's length under the flange","kind":"length","measurements":[{"id":"tdp","value":0.46,"unit":"in","pm":0.01,"stated":".47 -.02","source":{"type":"standard","doc":"US Army TDP drawing 9349056 (Post, Front Sight), rev G, PDF page 178, side view: the middle of .45 to .47","via":"user"}}]},"relief_length":{"label":"The unthreaded neck under the flange","kind":"length","measurements":[{"id":"tdp","value":0.062,"unit":"in","pm":0.005,"stated":".057 +.010","source":{"type":"standard","doc":"US Army TDP drawing 9349056 (Post, Front Sight), rev G, PDF page 178, side view: the middle of .057 to .067","via":"user"}}]},"thread_major_d":{"label":"The thread's major diameter","kind":"length","measurements":[{"id":"tdp","value":0.16045,"unit":"in","pm":0.00275,"stated":".164-36 UNF-2A ... MAJOR DIA .1577-.1632","source":{"type":"standard","doc":"US Army TDP drawing 9349056 (Post, Front Sight), rev G, PDF page 178","via":"user"}}]},"thread_pitch_d":{"label":"The thread's pitch diameter","kind":"length","measurements":[{"id":"tdp","value":0.1438,"unit":"in","pm":0.0014,"stated":"PITCH DIA .1424-.1452","source":{"type":"standard","doc":"US Army TDP drawing 9349056 (Post, Front Sight), rev G, PDF page 178","via":"user"}}]},"thread_pitch":{"label":"The thread's pitch","kind":"length","measurements":[{"id":"tdp","value":0.027778,"unit":"in","pm":0.000001,"stated":".164-36 UNF-2A","source":{"type":"standard","doc":"US Army TDP drawing 9349056 (Post, Front Sight), rev G, PDF page 178: 36 threads to the inch","via":"user"}}]},"end_chamfer":{"label":"The shank's end chamfer","kind":"length","measurements":[{"id":"tdp","value":0.025,"unit":"in","pm":0.005,"stated":".020 +.010 ... 43° +4°","source":{"type":"standard","doc":"US Army TDP drawing 9349056 (Post, Front Sight), rev G, PDF page 178, side view","via":"user"}}]},"detent_d":{"label":"The detent, its body's diameter","kind":"length","measurements":[{"id":"model","value":0.165,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight_Detent.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of the front sight detent)","method":"its body, a cylinder r 0.0825","via":"user"},"note":"In the base's .171 hole (8448566): the detent is out of sight under the post's flange, and only weighed."}]},"detent_length":{"label":"The detent, its body's length","kind":"length","measurements":[{"id":"model","value":0.435,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight_Detent.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of the front sight detent)","method":"its body, from y -0.498 to -0.063","via":"user"}}]},"detent_tip_d":{"label":"The detent's tip, its diameter","kind":"length","measurements":[{"id":"model","value":0.085,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight_Detent.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of the front sight detent)","method":"its tip, a cylinder r 0.0425","via":"user"}}]},"detent_tip_length":{"label":"The detent's tip, its length","kind":"length","measurements":[{"id":"model","value":0.063,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight_Detent.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of the front sight detent)","method":"its tip, from y -0.063 to 0","via":"user"}}]}}},{"subject":"aero-carbine-gas-tube","title":"Aero Precision gas tube, carbine length (APRH100017C stainless, APRH100281C melonite)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"aero","value":0.5,"unit":"oz","pm":0.05,"stated":"Weight(s) 0.5 oz","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, Gas Tube, Carbine Length - Stainless Steel (APRH100017C), Specifications","url":"https://www.aeroprecisionusa.com/gas-tube-carbine-length-stainless-steel","retrieved":"2026-10-06","via":"harvest"}},{"id":"aero-melonite","value":0.5,"unit":"oz","pm":0.05,"stated":"Weight(s) 0.5 oz","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, Gas Tube, Carbine Length - Melonite (APRH100281C), Specifications","url":"https://www.aeroprecisionusa.com/gas-tube-carbine-length-melonite","retrieved":"2026-10-06","via":"harvest"}},{"id":"midwayusa","value":0.5,"unit":"oz","pm":0.05,"stated":"Weight: 0.5 Ounce","source":{"type":"spec","publisher":"retailer","name":"MidwayUSA, Aero Precision Gas Tube Carbine Length AR-15 Stainless (its number 924189, the maker's APRH100017C), the product's data on its page","url":"https://www.midwayusa.com/product/1026894280","retrieved":"2026-10-06","via":"harvest"},"note":"A seller's table carrying the maker's figure: not a second weighing."}],"adopt":{"from":"aero","reason":"The page of the tube the part is by default; the melonite tube's page and a seller's table say the same."},"note":"Aero's own, on the page of each finish and in its list of the four lengths (\"Pistol - 0.2 oz / Carbine - 0.5 oz / Mid-Length - 0.64 oz / Rifle - 0.96 oz\", https://www.aeroprecisionusa.com/gas-tube-stainless-steel). Given to a tenth of an ounce: the ± is half of that. MidwayUSA's table has Aero's figure. A seller's \"Weight 1.44 oz\" beside \"Dimensions 11.1 × 1.2 × 1.2 in\" (AR15Discounts) and MidwayUSA's shipping weight for it (\"0.183 Pounds\") are the package's, not the tube's, and aren't readings of it."},"length":{"label":"Length","kind":"length","measurements":[{"id":"aero","value":9.75,"unit":"in","pm":0.005,"stated":"9.75\"","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, Gas Tube, Carbine Length - Stainless Steel (APRH100017C), Features","url":"https://www.aeroprecisionusa.com/gas-tube-carbine-length-stainless-steel","retrieved":"2026-10-06","via":"harvest"}},{"id":"aero-melonite","value":9.8,"unit":"in","pm":0.05,"stated":"Carbine length 9.8\"","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, Gas Tube, Carbine Length - Melonite (APRH100281C), Features","url":"https://www.aeroprecisionusa.com/gas-tube-carbine-length-melonite","retrieved":"2026-10-06","via":"harvest"}},{"id":"aero-family","value":9.8,"unit":"in","pm":0.05,"stated":"Pistol length 6.6875\", Carbine length 9.8\", Mid-Length 11.75”, Rifle length 15.125\"","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, Stainless Steel Gas Tubes (APPG100027, the four lengths), Features","url":"https://www.aeroprecisionusa.com/gas-tube-stainless-steel","retrieved":"2026-10-06","via":"harvest"},"note":"The same line is on the Melonite Gas Tubes page (https://www.aeroprecisionusa.com/gas-tube-melonite)."},{"id":"midwayusa","value":9.8,"unit":"in","pm":0.05,"stated":"Length: 9.8 Inches","source":{"type":"spec","publisher":"retailer","name":"MidwayUSA, Aero Precision Gas Tube Carbine Length AR-15 Stainless (its number 924189, the maker's APRH100017C), the product's data on its page","url":"https://www.midwayusa.com/product/1026894280","retrieved":"2026-10-06","via":"harvest"},"note":"The same table says \"Gas System Length: Carbine\"; its melonite tube's (116459) says \"Length: 9.8 Inches\" too."}],"adopt":{"from":"aero","reason":"The figure on this tube's own page, and the one given to the hundredth; 9.8 is the same length to a tenth, on the other finish's page and in the lists. What the app draws by either differs by 0.05 in at the tube's rear end, inside the receiver."},"note":"Aero states it two ways: 9.75 on the stainless carbine tube's own page, 9.8 on the melonite tube's page and in both of its lists of the four lengths. To the digits given the two are one length (9.75 is 9.8 to a tenth). Sellers split the same way: Classic Firearms \"9.75\"\" and AR15Discounts \"Length: 9.75 inches\"; Midwest Gun Works, Right to Bear and MidwayUSA \"Carbine length 9.8\"\". Nothing says how it is measured; end face to end face along the tube is what the photos are scaled by. Other makers' carbine tubes: BCM \"Length: Approximately 9 3/4\"\"; Primary Arms' guide \"Gas Tube Length: ~9.75”\"; Wing Tactical \"A carbine-length gas tube is 9.75 inches long\"."},"od":{"label":"Outside diameter","kind":"length","measurements":[{"id":"tdp","value":0.18,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{aero-mid-gas-tube.od}","via":"user"},"note":"The Army's drawing 8448567 (Gas Tube Assembly), \".1800 DIA REF\" at both ends: the head at its rear and the plugged front end. Its sources are in the mid-length tube's ledger."}],"note":"Aero gives none, and no seller's page does. The tube is the standard's: the carrier key's socket takes a .180 tube (std.ar15.carrier_key_bore_d, .1805), and Wing Tactical says of Aero's four stainless tubes \"Made to Mil-Spec dimensions\" (https://www.wingtactical.com/firearm-parts-accessories/ar-15-parts/gas-systems/gas-tubes/copy-of-aero-precision-melonite-gas-tubes/, a seller's sentence). The photos don't measure it: at the scale its length gives, the tube reads 0.15 to 0.17 in across by where the edge is taken (6 to 16% thin: a pixel is 0.011 to 0.013 in there, and bright metal and a black tube both lose their edges to a white ground)."},"bend_offset":{"label":"How far the tube drops at its bend (its rear run above its front)","kind":"length","measurements":[{"id":"tdp","value":0.156,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{aero-mid-gas-tube.bend_offset}","via":"user"},"note":"The Army's drawing 8448567, \".156\" (the rifle's tube): its sources are in the mid-length tube's ledger."},{"id":"photo-stainless","value":0.16,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/aero-carbine-gas-tube 4e863297f463 (MidwayUSA's picture 924189.jpg: the stainless carbine tube whole and level on white, 880 x 660) and d4a9aa9610b2 (Aero's gallery: the same tube, 1000 x 630)","scaleRef":"its published length between the end faces: 867.1 px = 88.9 px/in and 749.4 px = 76.9 px/in","method":"a level run, a round, a straight slope, a round and a level run fitted to the centre line (each column's upper and lower edge at the 225 and 240 levels): the drop reads 0.1596 and 0.1592 in one and 0.1568 and 0.1616 in the other; the two runs fitted each as its own line stand 0.1625 to 0.1677 apart at the bend's middle, being 0.07 to 0.15 degrees out of parallel","via":"harvest"}},{"id":"photo-melonite","value":0.14,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-carbine-gas-tube 0b1df4671af0 (Aero's gallery: the melonite carbine tube, 1000 x 630) and 25748a62f53b (MidwayUSA's 116459.jpg: the same photograph, larger)","scaleRef":"its published length between the end faces: 749.4 px = 76.9 px/in and 873.5 px = 89.6 px/in","method":"the two runs fitted each as its own line stand 0.143 and 0.139 in apart at the bend's middle","via":"harvest"},"note":"The two runs are 0.26 degrees out of parallel in this photograph (the tube's own bow, or how it lies): over the six inches between their middles that is 0.027 in, so where the drop is taken moves it by this ±."}],"adopt":{"from":"tdp","reason":"The drawing's, which the receiver's and the block's holes go by; this tube's photos read 0.16 and 0.14, either side of it."},"note":"The standard's: it takes the tube from the receiver's hole down to the block's (std.ar15.gas_tube_above_bore), whatever the length of the gas system."},"bend_radius":{"label":"The radius of each of the bend's two rounds, at the tube's centre line","kind":"length","measurements":[{"id":"tdp","value":1.5,"unit":"in","pm":0.5,"stated":"1.50 ±.50 R 2 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 8448567 (Gas Tube Assembly), rev F, PDF page 144: the side view (the rifle's tube); user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"}},{"id":"photo","value":3.6,"unit":"in","pm":0.4,"source":{"type":"photo","photo":"references/aero-carbine-gas-tube 4e863297f463 (MidwayUSA's picture 924189.jpg: the stainless carbine tube whole and level on white, 880 x 660) and d4a9aa9610b2 (Aero's gallery: the same tube, 1000 x 630)","scaleRef":"its published length between the end faces: 88.9 and 76.9 px/in","method":"a level run, a round, a straight slope, an equal round and a level run fitted to the centre line with the radius left free: 3.70 and 3.61 in the first photo (edges at the 225 and 240 levels; formal ± 0.15), 3.64 and 3.39 in the second (± 0.3), the slope between them 6.3 to 6.4 degrees and 1.0 in long","via":"harvest"},"note":"With the radius held at the drawing's 1.50 the fit is a quarter worse (1.3 to 1.4 thousandths rms against 1.1 in the first photo, a tenth of a pixel either way) and puts the bend from 3.80 to 5.44."}],"adopt":{"from":"photo","reason":"This tube's own picture, where the drawing is the rifle tube's; the fit with the radius free is the better one in both photos at every edge level. The bend's two ends below are read with it."},"note":"The Army's drawing is of the rifle's tube; where and how a carbine tube bends is on no drawing on file, so this tube's own photo is the reading. The two differ by less than 0.004 in anywhere along the centre line."},"bend_start_from_rear":{"label":"Where the bend begins, from the tube's rear (receiver) end","kind":"length","measurements":[{"id":"photo","value":3.71,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-carbine-gas-tube 4e863297f463 (MidwayUSA's picture 924189.jpg: the stainless carbine tube whole and level on white, 880 x 660) and d4a9aa9610b2 (Aero's gallery: the same tube, 1000 x 630)","scaleRef":"its published length between the end faces: 88.9 and 76.9 px/in","method":"where the first round leaves the rear run in the fit of bend_radius (radius free): 3.700 and 3.715 in the first photo, 3.715 and 3.714 in the second; the plain end is the rear, the end with the cross hole the front","via":"harvest"},"note":"The rifle's tube bends at 4.16 ±.25 (8448567), the mid-length's photo read 3.86 by eye. The melonite photograph's fit: 3.74 to 3.76."}]},"bend_end_from_rear":{"label":"Where the bend ends, from the tube's rear (receiver) end","kind":"length","measurements":[{"id":"photo","value":5.53,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-carbine-gas-tube 4e863297f463 (MidwayUSA's picture 924189.jpg: the stainless carbine tube whole and level on white, 880 x 660) and d4a9aa9610b2 (Aero's gallery: the same tube, 1000 x 630)","scaleRef":"its published length between the end faces: 88.9 and 76.9 px/in","method":"where the second round joins the front run in the fit of bend_radius (radius free): 5.533 and 5.531 in the first photo, 5.530 and 5.542 in the second","via":"harvest"},"note":"The melonite photograph's fit: 5.55 to 5.57. The centre line is halfway down the drop 4.63 to 4.66 in from the rear end."}]},"gas_hole_from_front":{"label":"The gas hole's centre behind the tube's front end","kind":"length","measurements":[{"id":"tdp","value":0.605,"unit":"in","pm":0.004,"source":{"type":"derived","expr":"{std.ar15.gas_tube_hole_from_front}","via":"user"},"note":"The Army's drawing 8448567, \".605 REF\"."},{"id":"photo","value":0.607,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aero-carbine-gas-tube 0b1df4671af0 (Aero's gallery: the melonite carbine tube, 1000 x 630), 25748a62f53b (MidwayUSA's larger copy of it) and d4a9aa9610b2 (Aero's stainless tube)","scaleRef":"its published length between the end faces: 76.9, 89.6 and 76.9 px/in","method":"the hole shows as a notch in one edge of the silhouette (the tube thinner there and its middle moved to the other edge): the notch's middle 0.607, 0.60 and 0.615 in from the end face nearest it","via":"harvest"},"note":"The notch is in the edge away from the rear run's side: the hole faces the barrel, as the drawing has it."}],"adopt":{"from":"tdp","reason":"The drawing; this tube's photos put its hole there within a pixel."},"note":"Where this tube touches the block: its hole over the block's port. The part's frame is here."},"gas_hole_d":{"label":"The gas hole's diameter","kind":"length","measurements":[{"id":"tdp","value":0.125,"unit":"in","pm":0.003,"stated":".125 DIA +.003 THRU THIS SIDE ONLY TO DEPTH SHOWN","source":{"type":"standard","doc":"US Army TDP drawing 8448567 (Gas Tube Assembly), rev F, PDF page 144: the view from below and Section A-A (\".125 DIA REF\", \".100 MAX\" deep); user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"The notch it makes in the photos' silhouette is 0.07 to 0.10 in long: a chord of it."}]},"pin_hole_from_front":{"label":"The roll pin's hole behind the tube's front end","kind":"length","measurements":[{"id":"tdp","value":0.187,"unit":"in","pm":0.003,"stated":".187 ±.003","source":{"type":"standard","doc":"US Army TDP drawing 8448567 (Gas Tube Assembly), rev F, PDF page 144: the side view; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"}},{"id":"photo","value":0.19,"unit":"in","pm":0.013,"source":{"type":"photo","photo":"references/aero-carbine-gas-tube 0b1df4671af0 (Aero's gallery: the melonite carbine tube, 1000 x 630) and 25748a62f53b (MidwayUSA's larger copy of it)","scaleRef":"its published length between the end faces: 76.9 and 89.6 px/in","method":"the white ground seen through the cross hole, a spot 4 and 7 px across on the black tube's middle: its centre 0.194 and 0.189 in from the front end face","via":"harvest"},"note":"Seen straight through from the side: the pin lies across the rifle, square to the plane of the bend, as the drawing has it."}],"adopt":{"from":"tdp","reason":"The drawing; the photo agrees within a pixel."}},"pin_hole_d":{"label":"The roll pin's hole, diameter","kind":"length","measurements":[{"id":"tdp","value":0.078,"unit":"in","pm":0.003,"stated":".078 DIA +.003 THRU","source":{"type":"standard","doc":"US Army TDP drawing 8448567 (Gas Tube Assembly), rev F, PDF page 144: the side view; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"Stated + .003 only. In the photo the hole is 0.05 to 0.08 in across (4 and 7 px)."}]},"crimp_front_from_front":{"label":"The front groove round the plugged end, its middle from the front end","kind":"length","measurements":[{"id":"photo","value":0.08,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aero-carbine-gas-tube 0b1df4671af0 (Aero's melonite tube), 25748a62f53b (MidwayUSA's larger copy of it), 4e863297f463 (MidwayUSA's stainless tube) and d4a9aa9610b2 (Aero's stainless tube)","scaleRef":"its published length between the end faces: 76.9, 89.6, 88.9 and 76.9 px/in","method":"where the tube reads thinnest, column by column, near its front end: 0.083, 0.057 to 0.068, 0.077 to 0.088 and 0.092 in from the end face","via":"harvest"}}],"note":"The tube is closed at the front by a plug (the Army's note 1: \"MAKE FROM GAS TUBE AND PLUG ASSEMBLY - 8448568\"), held by two grooves pressed round it, one each side of the pin's hole: the drawing shows them and gives them no figure."},"crimp_rear_from_front":{"label":"The rear groove round the plugged end, its middle from the front end","kind":"length","measurements":[{"id":"photo","value":0.295,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/aero-carbine-gas-tube 0b1df4671af0 (Aero's melonite tube), 25748a62f53b (MidwayUSA's larger copy of it), 4e863297f463 (MidwayUSA's stainless tube) and d4a9aa9610b2 (Aero's stainless tube)","scaleRef":"its published length between the end faces: 76.9, 89.6, 88.9 and 76.9 px/in","method":"where the tube reads thinnest behind the pin's hole: 0.291, 0.280, 0.302 and 0.301 to 0.314 in from the end face","via":"harvest"}}]},"crimp_width":{"label":"A groove's width along the tube","kind":"length","measurements":[{"id":"photo","value":0.035,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aero-carbine-gas-tube 0b1df4671af0 (Aero's melonite tube) and 25748a62f53b (MidwayUSA's larger copy of it)","scaleRef":"its published length between the end faces: 76.9 and 89.6 px/in","method":"the columns over which the tube reads thinner than beside the groove: three columns of 0.013 in and three to four of 0.011 in, at each groove","via":"harvest"},"note":"Two to four pixels: a groove this narrow is as wide as the photo's blur."}]},"crimp_depth":{"label":"A groove's depth, as the diameter it takes off","kind":"length","measurements":[{"id":"photo","value":0.011,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/aero-carbine-gas-tube 0b1df4671af0 (Aero's melonite tube), 25748a62f53b (MidwayUSA's larger copy of it) and 4e863297f463 (MidwayUSA's stainless tube)","scaleRef":"its published length between the end faces: 76.9, 89.6 and 88.9 px/in","method":"how much thinner the tube reads at a groove's middle than on the ring beside it: 0.9 to 1.1, 0.6 to 0.7 and 0.6 to 1.2 px","via":"harvest"},"note":"Read where the groove meets the silhouette's two edges, so it is a groove and not a band. A pixel's blur fills a groove this narrow: it is at least this deep."}]},"head_length":{"label":"The head at the tube's rear end, its length","kind":"length","measurements":[{"id":"photo","value":0.1,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-carbine-gas-tube 25748a62f53b (MidwayUSA's copy of Aero's melonite photograph), 0b1df4671af0 (Aero's own), 4e863297f463 (MidwayUSA's stainless tube) and d4a9aa9610b2 (Aero's stainless tube)","scaleRef":"its published length between the end faces: 89.6, 76.9, 88.9 and 76.9 px/in","method":"the columns from the rear end face over which the tube reads as thick as its body before it thins: 0.08 to 0.09, 0.11, 0.09 and 0.10 in","via":"harvest"},"note":"The head reads as thick as the tube ahead of the relief (within half a pixel either way in the four photos): it is drawn at the tube's diameter."}],"note":"The end that enters the carrier key. The drawing shows the head (its \".1800 DIA REF\" is taken across it) and gives its length no figure."},"end_break":{"label":"The broken rim of each end face, along the tube and across it","kind":"length","measurements":[{"id":"photo","value":0.015,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/aero-carbine-gas-tube 0b1df4671af0 (Aero's melonite tube), 25748a62f53b (MidwayUSA's larger copy of it) and 4e863297f463 (MidwayUSA's stainless tube)","scaleRef":"its published length between the end faces: 76.9, 89.6 and 88.9 px/in","method":"how much thinner the tube reads in the first column from each end face than two columns in: 0.7 to 1.5 px at the front and 0.6 to 0.9 px at the rear a side, within 0.014 in of the face; and Wing Tactical's view of a front end (acec2a7c502e) shows a flat face inside a broken rim","via":"harvest"},"note":"A pixel: as large as the picture's blur. Drawn as a chamfer this size at both ends."}],"note":"Both end faces have their rims broken, the rear one's (the head's, which enters the carrier key) the more; the Army's drawing shows both rounded and sizes neither."},"relief_end_from_rear":{"label":"Where the thinner stretch behind the head ends, from the tube's rear end","kind":"length","measurements":[{"id":"photo","value":2.27,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-carbine-gas-tube 0b1df4671af0 (Aero's melonite tube), 25748a62f53b (MidwayUSA's larger copy of it), 4e863297f463 (MidwayUSA's stainless tube) and d4a9aa9610b2 (Aero's stainless tube)","scaleRef":"its published length between the end faces: 76.9, 89.6, 88.9 and 76.9 px/in","method":"the tube's thickness by tenths of an inch from the rear end steps up between the stations at 2.2 and 2.3 in in three of the photos and between 2.1 and 2.4 in the fourth; in Midwest Gun Works' enlargement of the fourth (de71b2b39a4d, 140 px/in) between 2.28 and 2.30","via":"harvest"}}],"note":"Between its head and this station the tube is thinner than ahead of it: a line across the tube in every photo, with a different sheen behind it."},"relief_depth":{"label":"How much thinner the stretch behind the head is than the tube ahead of it, on the diameter","kind":"length","measurements":[{"id":"photo","value":0.013,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/aero-carbine-gas-tube 0b1df4671af0 (Aero's melonite tube), 25748a62f53b (MidwayUSA's larger copy of it), 4e863297f463 (MidwayUSA's stainless tube) and d4a9aa9610b2 (Aero's stainless tube)","scaleRef":"its published length between the end faces: 76.9, 89.6, 88.9 and 76.9 px/in","method":"the median thickness over 0.5 to 2.0 in from the rear end against that over 2.5 to 4.0 in: 0.9, 1.25, 1.0 and 1.35 px less, which is 0.012, 0.014, 0.011 and 0.018 in","via":"harvest"},"note":"A difference of about one pixel, the same way in four photos of two finishes. Which of the two stretches is the drawing's .180 isn't read (the photos give no diameter): the head and the tube ahead of the relief are drawn at it, and the relief this much under."}]},"plug_length":{"label":"The plug in the front end, its length from the front end face","kind":"length","measurements":[{"id":"tdp","value":0.44,"unit":"in","pm":0.03,"source":{"type":"standard","doc":"US Army TDP drawing 8448567 (Gas Tube Assembly), rev F, PDF page 144: the view from below, scaled between its own .187 (the pin's hole from the end: 0.415) and .605 (the gas hole from the end: 0.46), which differ by a tenth on the scan; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"It ends ahead of the gas hole's front edge (0.54 from the end), as it must."}],"note":"Where the tube's bore ends. Not a callout: the plug's own drawing (8448568) isn't in the package."},"bore":{"label":"The tube's bore","kind":"length","measurements":[{"id":"weight","value":0.134,"unit":"in","pm":0.006,"source":{"type":"derived","basis":"The bore of a plain tube of this length (9.75 in) and diameter (.180) that weighs Aero's 0.5 oz as stainless steel at std.density.stainless_416 (127 g to the cubic inch): 14.17 g is 0.1116 cubic inches, a wall of 0.01145 square inches, which leaves a bore of 0.1335. By the weight's half digit (0.45 to 0.55 oz): 0.139 to 0.128. The plug, the relief and the holes are left out of it.","via":"harvest"},"note":"Aero names no grade of stainless; a seller says of gas tubes in general \"Most AR-15 gas tubes are made from 304 stainless steel\" (Wing Tactical, https://www.wingtactical.com/gas-tubes/), which is 3% denser and would make the bore 0.135."},{"id":"tdp-section","value":0.091,"unit":"in","pm":0.008,"source":{"type":"standard","doc":"US Army TDP drawing 8448567 (Gas Tube Assembly), rev F, PDF page 144: Section A-A, scale 10/1, scaled (the bore's circle is 0.503 of the tube's across, 180 px of 357 on the page's image: 0.503 of .180); user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"Not a callout, and the section is a sketch: its .125 hole reads .117 and its .100 depth .096 against the same .180. A tube with this bore would weigh 0.8 oz at this length; Aero says 0.5."}],"adopt":{"from":"weight","reason":"This product's own figure, where the section is the Army's tube drawn without a dimension. It shows only at the tube's open rear end, inside the receiver."},"note":"No page and no callout gives it. Two readings that don't agree: what Aero's weight leaves of a .180 tube, and the Army's section as drawn."}}},{"subject":"aero-charging-handle","title":"Aero Precision AR15/M4 5.56 charging handle (APRH100000C)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"aero","value":1.1,"unit":"oz","pm":0.05,"stated":"Weight(s) 1.1 oz","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, AR15/M4 5.56 Charging Handle (APRH100000C), Specifications","url":"https://www.aeroprecisionusa.com/ar15-charging-handle","retrieved":"2026-10-02","via":"harvest"}}]},"length":{"label":"The shaft: the T's front face (its shoulder) to the front hook's tip","kind":"length","measurements":[{"id":"tdp","value":5.895,"unit":"in","pm":0.01,"stated":"5.600 and .295","source":{"type":"standard","doc":"US Army TDP drawing 8448518 (Handle, Charging), rev G, scale 2/1, PDF page 128, side view"},"note":"The shoulder to the hook's rear face, and that face to its tip; they close with 5.710 REF + .40 = .215 + 5.600 + .295."}],"note":"The handle is the standard's: Aero's is a mil-spec handle and states no size."},"t_width":{"label":"The T, side to side","kind":"length","measurements":[{"id":"tdp","value":2.1,"unit":"in","pm":0.05,"source":{"type":"standard","doc":"US Army TDP drawing 8448518 (Handle, Charging), rev G, scale 2/1, PDF page 128, the plan view and Section G-G, scaled at 316 px/in (665 and 656 px)"}},{"id":"photo","value":2,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-charging-handle ad1e8e613ad3 (Aero's gallery: the charging handle from above, 1000 x 630)","scaleRef":"the shaft's .400 (shaft_width, 54 px) and the shoulder to the hook's tip as the drawing's length (797 px): both 135.2 px/in","method":"the T's tips, rows 187-456 at px 67-73; the latch's thumb tab reaches 0.06 further on the left (row 179)","via":"harvest"}},{"id":"model","value":2.053,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Charging_Handle.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec handle)","method":"its extent across, from the STEP text's vertices","via":"user"}}],"adopt":{"from":"photo","reason":"Aero's own handle at two agreeing scales; the drawing's T is a forging's outline, scaled (2.1), and the model's 2.05: kept visible."},"note":"Not a callout: the T is 'AS FORGED' and its forging drawing (D8448647) isn't in the package."},"t_depth":{"label":"The T, its rear face to the shoulder","kind":"length","measurements":[{"id":"tdp","value":0.95,"unit":"in","pm":0.03,"source":{"type":"standard","doc":"US Army TDP drawing 8448518 (Handle, Charging), rev G, scale 2/1, PDF page 128, top and side views, scaled (297 to 300 px)"}},{"id":"photo","value":0.865,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-charging-handle ad1e8e613ad3 (Aero's gallery: the charging handle from above, 1000 x 630)","scaleRef":"the shaft's .400 (shaft_width, 54 px) and the shoulder to the hook's tip as the drawing's length (797 px): both 135.2 px/in","method":"the T's rearmost point (px 43) to the shoulder (px 160)","via":"harvest"}},{"id":"model","value":0.9,"unit":"in","pm":0.02,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Charging_Handle.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec handle)","method":"its overall 6.796 less the drawing's 5.895","via":"user"}}],"adopt":{"from":"photo","reason":"As t_width; the drawing's is scaled, not a callout."},"note":"Not a callout: the length is labelled -E- (note 3's grit-blast length) with no value."},"t_height":{"label":"The T's height: the shaft's thickness and the T's top above it","kind":"length","measurements":[{"id":"tdp","value":0.4235,"unit":"in","pm":0.024,"stated":".2985 ±.0035 and .125 ±.020 AS FORGED","source":{"type":"standard","doc":"US Army TDP drawing 8448518 (Handle, Charging), rev G, scale 2/1, PDF page 128, side view"},"note":"The T's underside is drawn flush with the shaft's."}]},"t_block_length":{"label":"The block ahead of the T's raised top: from where the raised top ends to the shoulder","kind":"length","measurements":[{"id":"tdp","value":0.425,"unit":"in","pm":0.02,"stated":".21 and .215 ±.010","source":{"type":"standard","doc":"US Army TDP drawing 8448518 (Handle, Charging), rev G, scale 2/1, PDF page 128, side view"},"note":"The .21 is a two-place figure (±.01 by the title block)."}],"note":"Behind this the T stands t_height high; ahead of it the block is as thick as the shaft: it is what lies in the receiver's notch, under the rail's rear end. Taken as: the AS FORGED top's front edge to the line .215 behind the shoulder, and that line to the shoulder. In the plan the arc's ends (t_nest_r about a centre .343 behind the shoulder) are 0.425 behind it too, 0.43 off the centre line."},"t_nest_r":{"label":"The arc cut in the T's raised top, concave to the front: its radius","kind":"length","measurements":[{"id":"tdp","value":0.437,"unit":"in","pm":0.01,"stated":".437 R ±.010","source":{"type":"standard","doc":"US Army TDP drawing 8448518 (Handle, Charging), rev G, scale 2/1, PDF page 128, plan view"}},{"id":"photo","value":0.46,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-charging-handle ad1e8e613ad3 (Aero's gallery: the charging handle from above, 1000 x 630)","scaleRef":"the shaft's .400 (shaft_width, 54 px) and the shoulder to the hook's tip as the drawing's length (797 px): both 135.2 px/in","method":"the circle through the arc's apex (t_nest_apex's photo reading) and its two walls on column 79, 0.6 behind the shoulder: the shadow's edge at row 270 and the bright edge at row 371, each 50.5 px from the shaft's centre row 320.5 (0.374); ± is two pixels at each of the three points","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's callout; Aero's own handle reads 0.02 more, within the photo's ±."},"note":"Where the rounded rear end of a receiver's rail nests in the T (the Army's upper has it at .375 R: 8448524, the plan view): inside the arc the top is the block's, as thick as the shaft. Symmetric about the shaft's centre line (datum B). Aero's photo from above shows the arc on this handle: its wall is in shadow on the side the light comes from and bright on the other."},"t_nest_apex":{"label":"The arc's apex behind the shoulder","kind":"length","measurements":[{"id":"tdp","value":0.78,"unit":"in","pm":0.01,"stated":".780","source":{"type":"standard","doc":"US Army TDP drawing 8448518 (Handle, Charging), rev G, scale 2/1, PDF page 128, plan view"}},{"id":"photo","value":0.79,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aero-charging-handle ad1e8e613ad3 (Aero's gallery: the charging handle from above, 1000 x 630)","scaleRef":"the shaft's .400 (shaft_width, 54 px) and the shoulder to the hook's tip as the drawing's length (797 px): both 135.2 px/in","method":"on the shaft's centre row (320.5) the T's top steps down at px 53 to 54 (its wall in shadow from there to px 63), the T's rear being at px 43 to 45 and the shoulder at px 160: 106.5 px","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's callout; Aero's own handle reads 0.01 more, within the photo's ±."},"note":"The arc's rearmost point, on the centre line: its centre is this less t_nest_r behind the shoulder (.343). Checked on the scan: the arc's apex is 248 px behind the shoulder's line at 316 px/in (0.785)."},"shaft_width":{"label":"The shaft's width","kind":"length","measurements":[{"id":"tdp","value":0.4,"unit":"in","pm":0.005,"stated":".400 -B-","source":{"type":"standard","doc":"US Army TDP drawing 8448518 (Handle, Charging), rev G, scale 2/1, PDF page 128, plan view"}}]},"shaft_thickness":{"label":"The shaft's thickness","kind":"length","measurements":[{"id":"tdp","value":0.2985,"unit":"in","pm":0.0035,"stated":".2985 ±.0035","source":{"type":"standard","doc":"US Army TDP drawing 8448518 (Handle, Charging), rev G, scale 2/1, PDF page 128, side view"}}]},"latch_reach":{"label":"How far the latch stands out","kind":"length","measurements":[],"note":"Not published."},"guide_lug_height":{"label":"The guide lugs' height, from the shaft's underside up","kind":"length","measurements":[{"id":"standard","value":0.119,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{bcm-mk2-charging-handle.guide_lug_height}","via":"harvest"},"note":"US Army TDP drawing 8448518, end view: .119 ±.002."}],"note":"Until 2026-10-20 the lugs were drawn as the plan's two bumps at the shaft's whole thickness, and stood out of the channel's tier into the tier over it in every upper."},"shoulder_break_height":{"label":"The block's front corners beside the shaft: how far each is broken, from the shaft's top or underside","kind":"length","measurements":[{"id":"tdp","value":0.083,"unit":"in","pm":0.005,"stated":".083, BOTH SIDES 2 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 8448518 (Handle, Charging), rev G, scale 2/1, PDF page 128, side view, at the shoulder"}}],"note":"Where the block's shoulder meets the notch's front wall in an upper, whose own corners are cut back at 45 degrees (std.ar15.charging_handle_notch_chamfer): the block's, at 47, clear them."},"shoulder_break_angle":{"label":"The block's front corners beside the shaft: the break's angle from the shoulder's face","kind":"angle","measurements":[{"id":"tdp","value":47,"unit":"deg","pm":1,"stated":"47° ±1°, 4 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 8448518 (Handle, Charging), rev G, scale 2/1, PDF page 128, side view, at the shoulder"},"note":"Read as from the shoulder's upright face: the arc is drawn from it."}]},"catch_bottom":{"label":"The latch's hook arm ahead of the shoulder (what catches the receiver, on the left): its underside above the shaft's underside","kind":"length","measurements":[{"id":"model","value":0.1,"unit":"in","pm":0.004,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Charging_Handle.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec handle)","method":"its faces from the STEP text in its own frame (the shaft's underside at Y -0.020): the latch's slot across the T, planes Y 0.080 and 0.211 from the shaft's left face (X 0.190) out to the T's end, from Z -0.790 to 0.125, 0.02 ahead of the shoulder: its floor 0.100 over the underside","via":"user"}}],"note":"The latch lies in a slot across the T at mid-height, and its arm runs forward out of it along the shaft's left side to the hook. Aero's photo is from above; the latch's own drawing (8448519) isn't in the package."},"catch_thickness":{"label":"The latch's hook arm: its thickness","kind":"length","measurements":[{"id":"model","value":0.123,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Charging_Handle_Latch.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec handle's latch)","method":"its extent from the STEP text: a plate 0.123 thick (Z 0 to 0.123), in the handle's slot 0.131 high","via":"user"}}]}}},{"subject":"aero-enhanced-15-handguard","title":"Aero Precision AR15 15\" Enhanced M-LOK Handguard, Gen 2 (APRA100218C alone, APRA100218A with the BAR barrel nut)","dimensions":{"weight":{"label":"Weight (the handguard, as Aero states it for the 15 in)","kind":"mass","measurements":[{"id":"aero","value":11.2,"unit":"oz","pm":0.05,"stated":"Weight(s) 7\" - 5.6oz, 9\" - 7.2oz, 12\" - 9.6oz, 15\" - 11.2oz","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, AR15 Enhanced M-LOK Handguards, Gen 2 (every length and finish), Specifications","url":"https://www.aeroprecisionusa.com/ar15-enhanced-mlok-handguards","retrieved":"2026-10-12","via":"harvest"}},{"id":"wing-tactical","value":11.2,"unit":"oz","pm":0.05,"stated":"Weight : 7-Inch: 5.6 oz. 9-Inch: 7.2 oz. 12-Inch: 9.6 oz. 15-Inch: 11.2 oz.","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Aero Precision AR-15 Enhanced M-LOK Rail (the 7, 9, 12 and 15 in with the barrel nut), Specifications","url":"https://www.wingtactical.com/firearm-parts-accessories/aero-precision-ar-15-enhanced-m-lok-rail/","retrieved":"2026-10-12","via":"harvest"},"note":"The seller of the one with the nut, its screws and its shims in the box states the same figure."},{"id":"ar15discounts","value":11.2,"unit":"oz","pm":0.05,"stated":"Weight 11.2 oz","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, APRA100218C - Aero Precision Enhanced M-LOK AR-15 Handguard Gen 2 Black - 15\", Additional information","url":"https://ar15discounts.com/products/aero-precision-enhanced-m-lok-ar-15-handguard-gen-2-black-15/","retrieved":"2026-10-12","via":"harvest"},"note":"The seller of the handguard alone; beside it \"Dimensions 20.5 × 3 × 3 in\", a carton's."}],"adopt":{"from":"aero","reason":"The maker's own figure; both sellers repeat it."},"note":"Aero's one figure for the 15 in, under a list for the four lengths; no page says whether the BAR barrel nut, the eight screws or the shims are in it. The same figure stands on the page of the handguard alone's sellers and on the page of the one sold with the nut, so it is taken as the handguard's own; the model as 6061 aluminium is the check (app/tests/aero-enhanced-15-handguard.test.ts)."},"bar_nut_weight":{"label":"Weight of the BAR barrel nut (APRH100268), which the one sold for a standard upper comes with","kind":"mass","measurements":[{"id":"aero","value":2.24,"unit":"oz","pm":0.005,"stated":"Weight(s) 2.24 oz","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, AR15 BAR Barrel Nut (APRH100268), Specifications","url":"https://www.aeroprecisionusa.com/ar15-bar-barrel-nut","retrieved":"2026-10-12","via":"harvest"},"note":"\"Material: Machined from Billet 7075-T6 Aluminum\"; \"Includes: BAR Barrel Nut / BAR Shim Pack (8 shims)\"."}]},"weight_with_nut":{"label":"Weight on a standard upper: the handguard and its BAR barrel nut","kind":"mass","measurements":[{"id":"sum","value":13.44,"unit":"oz","pm":0.06,"source":{"type":"derived","expr":"{.weight} + {.bar_nut_weight}","via":"harvest"}}],"note":"Worked out: Aero's two figures added. The eight screws and the shims aren't weighed on any page and aren't in it."},"length":{"label":"Length as Aero measures it: from where it meets the receiver to the end of its rail's teeth","kind":"length","measurements":[{"id":"aero","value":14.94,"unit":"in","pm":0.005,"stated":"Actual Handguard Lengths 7\" - 7.25\", 9\" - 9.22\", 12\" - 12.63\", 15\" - 14.94\"","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, AR15 Enhanced M-LOK Handguards, Gen 2 (every length and finish), Specifications","url":"https://www.aeroprecisionusa.com/ar15-enhanced-mlok-handguards","retrieved":"2026-10-12","via":"harvest"}},{"id":"photo","value":14.97,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard f5565b43bbb0 (AR15Discounts: the 15 in black handguard's right side, 1920 x 1280)","scaleRef":"SIDE (the file's header): its 37 rail slots on the Picatinny pitch, 106.58 px/in in the rail's plane","method":"the last tooth's front edge (column 1775.5: 15.083 in ahead of the tube's rear face) less where the rail's neck begins (column 171: 0.110)","via":"harvest"}}],"adopt":{"from":"aero","reason":"The maker's figure, to two places; the photo's reading of what Aero says it measures agrees within 0.03 in."},"note":"Aero: \"Aero Precision rail lengths measure from end to end. This is the point of contact at the receiver to the end of the last picatinny slot at the muzzle.\" The point of contact is the rear end of its rail, which meets the receiver's rail; the tube's own rear face reaches a tenth of an inch further back, round the receiver's front (rail_rear_from_rear). On the side photo the last tooth's front stands 14.97 in ahead of that point, and the rail's floor runs on 0.06 in past it to the front end (overall_length)."},"overall_length":{"label":"Overall length, from the tube's rear face to the front end","kind":"length","measurements":[{"id":"photo","value":15.14,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard f5565b43bbb0 (AR15Discounts: the 15 in black handguard's right side, 1920 x 1280)","scaleRef":"SIDE (the file's header): the side flat's own plane, its seven M-LOK slots on the M-LOK pitch (109.15 px/in)","method":"the side flat's rear edge to its front edge at the M-LOK row, columns 142 to 1797 (1656 px, 15.17 in), and the rail's own nose at the rail's scale (column 1786: 15.13 in from the rear face): the middle; ± covers both and two pixels","via":"harvest"}}],"note":"A tenth of an inch of tube behind the point Aero measures from, and 0.06 in of the rail's floor ahead of the last tooth. Aero's later list of handguard lengths (handguard_length_tech_manual_2022.pdf, page 4) names this one 15\"."},"width":{"label":"Width across the side flats","kind":"length","measurements":[{"id":"wing-tactical","value":1.92,"unit":"in","pm":0.005,"stated":"Outside Diameter : Width - 1.92\", Height - 2.18\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Aero Precision AR-15 Enhanced M-LOK Rail (the 7, 9, 12 and 15 in with the barrel nut), Specifications","url":"https://www.wingtactical.com/firearm-parts-accessories/aero-precision-ar-15-enhanced-m-lok-rail/","retrieved":"2026-10-12","via":"harvest"}}],"note":"A seller's table, with no word of where it comes from; the maker gives no outside size. Across its two side flats (the M-LOK faces at 3 and 9 o'clock), by Wing's own view down its length: the BAR nut's rim in the rear face's plane reads about 382 px (by eye, on a crop enlarged 2.5 times) to the face's 412, which with the published 1.78 in nut cut is 1.92."},"height":{"label":"Height, from the rail's top to the bottom flat","kind":"length","measurements":[{"id":"wing-tactical","value":2.18,"unit":"in","pm":0.005,"stated":"Outside Diameter : Width - 1.92\", Height - 2.18\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Aero Precision AR-15 Enhanced M-LOK Rail (the 7, 9, 12 and 15 in with the barrel nut), Specifications","url":"https://www.wingtactical.com/firearm-parts-accessories/aero-precision-ar-15-enhanced-m-lok-rail/","retrieved":"2026-10-12","via":"harvest"}}],"note":"A seller's table (as the width). What it spans: the rail's top to the flat at 6 o'clock. With the rail level with the receiver's (rail_top_above_bore, 1.2125 above the bore) it puts the bottom flat 0.9675 below the bore, and half the width is 0.96: the body is as far below the bore as it is wide to each side. The side photo's rail top, M-LOK row and bottom edge land on it with the lens 9 degrees above level (the file's header)."},"inside_diameter":{"label":"Inside diameter, from the barrel nut cut to the front end","kind":"length","measurements":[{"id":"aero","value":1.72,"unit":"in","pm":0.005,"stated":"1.72\" inside diameter (from barrel nut cut to forward end) fits most muzzle devices and 1.5\" suppressors","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, AR15 Enhanced M-LOK Handguards, Gen 2 (every length and finish), Features","url":"https://www.aeroprecisionusa.com/ar15-enhanced-mlok-handguards","retrieved":"2026-10-12","via":"harvest"}},{"id":"wing-tactical","value":1.72,"unit":"in","pm":0.005,"stated":"Inside Diameter : 1.72\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Aero Precision AR-15 Enhanced M-LOK Rail (the 7, 9, 12 and 15 in with the barrel nut), Specifications","url":"https://www.wingtactical.com/firearm-parts-accessories/aero-precision-ar-15-enhanced-m-lok-rail/","retrieved":"2026-10-12","via":"harvest"}},{"id":"aero-15-page","value":1.78,"unit":"in","pm":0.005,"stated":"1.78\" inside diameter fits most muzzle devices and 1.5\" suppressors","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, AR15 15\" Enhanced M-LOK Handguard, Gen 2 - Anodized Black (APRA100218C), Features","url":"https://www.aeroprecisionusa.com/ar15-15inch-m-lok-handguard-gen2","retrieved":"2026-10-12","via":"harvest"},"note":"The 15 in's own page gives one inside diameter, and it is the figure the page of all lengths gives for the barrel nut cut."}],"adopt":{"from":"aero","reason":"Aero's page of every length tells the two apart (1.72 ahead of the barrel nut cut, 1.78 in it), its 2022 list of lengths says \"The 1.72\\\" ID of the Enhanced Handguard\", and a seller's table has 1.72; the 15 in's own page has the nut cut's figure in the sentence about muzzle devices."},"note":"Across the inside of the two side flats: the muzzle end's photos show flat inner walls that follow the outside, a tenth of an inch in (the width less this, halved)."},"nut_cut_diameter":{"label":"Inside diameter at the rear, where the BAR barrel nut (or the Enhanced upper's platform) goes","kind":"length","measurements":[{"id":"aero","value":1.78,"unit":"in","pm":0.005,"stated":"1.78\" inside barrel nut cut area diameter","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, AR15 Enhanced M-LOK Handguards, Gen 2 (every length and finish), Features","url":"https://www.aeroprecisionusa.com/ar15-enhanced-mlok-handguards","retrieved":"2026-10-12","via":"harvest"}}]},"nut_cut_depth":{"label":"How far in from the rear face the barrel nut cut runs","kind":"length","measurements":[{"id":"photo","value":1.6,"unit":"in","pm":0.2,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard f5565b43bbb0 (AR15Discounts: the 15 in black handguard's right side, 1920 x 1280)","scaleRef":"SIDE (the file's header)","method":"bounded, not read: between screw_hole0_from_rear + screw_hole_spacing + half the countersink's rim, and vent_slot0_from_rear less half a slot's length","via":"harvest"}}],"note":"No page gives it. It ends ahead of the front screw hole's rim (1.37 in from the rear face) and behind the rear ends of the first slots through its walls (1.81 in): the middle of the two, with half the room either way. It shows only from the rear end, which stands against the receiver."},"rear_x":{"label":"The tube's rear face ahead of the receiver's front face (negative: behind it, round the receiver's front)","kind":"length","measurements":[{"id":"shoulder","value":-0.555,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"-{std.ar15.upper_barrel_thread_length} - {.rail_rear_from_rear}","via":"harvest"}}],"note":"Where it meets the receiver is the rear end of its rail, and that stands at the receiver body's front shoulder, the foot of the barrel-nut thread: Aero's manual for the BAR nut (bar-barrel-nut-instructions.pdf, step 10: \"Install your handguard and you are now done.\") photographs one on a standard upper with its rail carrying on from the receiver's, and the Army's drawing puts that shoulder .445 behind the thread's end, where the app's handguards are placed from. The tube's rear face is a tenth of an inch further back (rail_rear_from_rear). Two things say that the rail's rear end, not the tube's, is at the shoulder: so placed, its first rail slot stands 0.524 in ahead of the shoulder, where the M4E1 Enhanced receiver's own row of slots comes to at the standard's pitch (0.497: aero-m4e1-enhanced-upper.rail_slot0_x and fifteen pitches); and its screw holes stand 0.71 and 1.12 ahead of it, where that receiver's platform has its own (0.74 and 1.15 by its own photo). The shims between the BAR nut and the shoulder (.002 and .003 in) aren't counted."},"rail_top_above_bore":{"label":"Its rail's top above the bore axis","kind":"length","measurements":[{"id":"level","value":1.2125,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.rail_top_above_pin} - {aero-m4e1-threaded-upper.bore_axis_above_pin}","via":"harvest"}}],"note":"Level with the receiver's rail: Aero's M4E1 uppers have a \"Picatinny profile that blends seamlessly with our Enhanced Handguards\" (its page for the M4E1 Enhanced upper without a forward assist, APAR612201AC, and its page for the M4E1 Threaded upper names the Enhanced handguards too). So the receiver's rail top above the pin line less the bore's height above it. The seller's height less half the seller's width is 1.22."},"side_flat_height":{"label":"The side flat (the M-LOK face at 3 and 9 o'clock), from its lower edge to its upper","kind":"length","measurements":[{"id":"rear-view","value":0.93,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard 6dcc345de6bf (Wing Tactical: a long one from its rear end, the BAR nut in it, 1280 x 1280)","scaleRef":"REAR (the file's header): 214.6 px/in across, 0.883 of it up and down","method":"the rear face's left and right edges stand upright (within 5 px) from row 908 to row 1084: 176 px","via":"harvest"}},{"id":"side-view","value":0.95,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard f5565b43bbb0 (AR15Discounts: the 15 in black handguard's right side, 1920 x 1280)","scaleRef":"SIDE (the file's header): 109.15 px/in on the side flat, heights over 0.988","method":"the flat's even tone between the two inner rows of slots, rows 655 to 759 (104 px), about the M-LOK row at 709","via":"harvest"}}],"adopt":{"from":"rear-view","reason":"The view that shows the flat's two ends as corners of the outline; the side view, where they are the edges of two rows of slots, agrees within 0.02 in."}},"ridge_across":{"label":"Across the two ridges between the faces above (and below) a side flat: each side has a steep face and a shallow one","kind":"length","measurements":[{"id":"rear-view","value":1.44,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard 6dcc345de6bf (Wing Tactical: a long one from its rear end, the BAR nut in it, 1280 x 1280)","scaleRef":"REAR (the file's header): 214.6 px/in across","method":"where the outline's slope changes on the lower left (from 1.33 down per px across to 0.44): column 498, 154 px from the nut's centre line (652), doubled","via":"harvest"}}],"note":"Between a side flat and the flat at the bottom the outline isn't one face: it leaves the chord between their ends by 22 px (0.10 in) at its middle, as two faces with a ridge between (the muzzle end's photos show the two apart, each with its own row of slots). The ridge lies at 47 degrees about the bore: the eight screws, which go in along the BAR nut's 45 degree holes, are countersunk on it."},"ridge_from_bore":{"label":"Those ridges above (and below) the bore's level","kind":"length","measurements":[{"id":"rear-view","value":0.79,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard 6dcc345de6bf (Wing Tactical: a long one from its rear end, the BAR nut in it, 1280 x 1280)","scaleRef":"REAR (the file's header): 214.6 px/in across, 0.883 of it up and down; the bottom flat (row 1188) at height less rail_top_above_bore below the bore","method":"the lower left ridge at row 1157, 31 px above the bottom flat's row: 0.164 in above the flat, which is 0.9675 below the bore (0.80); from the nut's centre row (1010) the same point reads 0.776: the middle","via":"harvest"},"note":"The side view agrees: the ridge would stand at row 621 above the M-LOK row and 787 below it, between the two rows of slots each side (bars at 626 to 634 and 774 to 786), where the upper screw holes' rims begin (623)."}]},"bottom_flat_width":{"label":"The flat at 6 o'clock, across (and the shelf each side of the rail's neck ends as far out)","kind":"length","measurements":[{"id":"rear-view","value":0.88,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard 6dcc345de6bf (Wing Tactical: a long one from its rear end, the BAR nut in it, 1280 x 1280)","scaleRef":"REAR (the file's header): 214.6 px/in across","method":"the bottom edge lies level (rows 1186 to 1188) from column 556 to 745: 189 px","via":"harvest"},"note":"The top shelf's outer end is the same distance from the middle on the side view (its edge at row 598 is 0.954 above the bore at 0.44 out)."}]},"neck_width":{"label":"The rail's neck, across its two walls","kind":"length","measurements":[{"id":"rear-view","value":0.67,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard 6dcc345de6bf (Wing Tactical: a long one from its rear end, the BAR nut in it, 1280 x 1280)","scaleRef":"the rail's own head at its rear end, 172 px across for the standard's 0.835 in (std.picatinny.top_width): 206 px/in there","method":"the two walls' outer faces under the head, 138 px apart","via":"harvest"}}]},"channel_width":{"label":"The channel under the rail (the gas tube's), across","kind":"length","measurements":[{"id":"rear-view","value":0.5,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard 6dcc345de6bf (Wing Tactical: a long one from its rear end, the BAR nut in it, 1280 x 1280)","scaleRef":"the rail's own head at its rear end, 172 px across for the standard's 0.835 in (std.picatinny.top_width): 206 px/in there","method":"the dark opening between the neck's walls, columns 598 to 701: 103 px","via":"harvest"}}]},"channel_roof_below_rail_top":{"label":"That channel's roof below the rail's top","kind":"length","measurements":[{"id":"rear-view","value":0.165,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard 6dcc345de6bf (Wing Tactical: a long one from its rear end, the BAR nut in it, 1280 x 1280)","scaleRef":"the rail's own head at its rear end (206 px/in), 0.883 of it up and down","method":"the head's rear end face, from its top edge (row 788) to the channel's roof (818): 30 px","via":"harvest"}}]},"rail_slots":{"label":"How many rail slots (each between two teeth)","kind":"count","measurements":[{"id":"photo","value":37,"unit":"count","source":{"type":"photo","photo":"references/aero-enhanced-15-handguard f5565b43bbb0 (AR15Discounts: the 15 in black handguard's right side, 1920 x 1280)","scaleRef":"SIDE (the file's header)","method":"counted along the top edge: the runs where the silhouette's top is at the slots' floor, between the shelf behind the first tooth and the open floor ahead of the last (side_pure.py: 39 runs, the first and the last being those two)","via":"harvest"}},{"id":"level","value":37,"unit":"count","source":{"type":"photo","photo":"references/aero-enhanced-15-handguard 9b7983046ad2 (Aero: the 15 in Kodiak Brown handguard's right side, level, 1000 x 630)","scaleRef":"none: a count","method":"counted again along the top edge of Aero's own level photo of the Kodiak Brown one: 39 runs, the first and the last being the shelf and the open floor","via":"harvest"}}],"adopt":{"from":"photo","reason":"The larger photo; Aero's own counts the same."},"note":"38 teeth; ahead of the last the rail's floor runs out open to the front end."},"rail_slot0_from_rear":{"label":"The rearmost rail slot's centre ahead of the rear face","kind":"length","measurements":[{"id":"photo","value":0.634,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard f5565b43bbb0 (AR15Discounts: the 15 in black handguard's right side, 1920 x 1280)","scaleRef":"SIDE (the file's header): the 37 slots' centres fit the pitch from column 235.5 (41.96 px a pitch, 106.58 px/in); the rear face from its near edge on the side flat, column 142, 0.96 in nearer the lens","method":"X of column 235.5 at the rail's depth; ± is the lens's place along the photo (150 px) and the rear edge (2 px)","via":"harvest"}}]},"rail_rear_from_rear":{"label":"The rail's rear end (its neck's: where it meets the receiver) ahead of the tube's rear face","kind":"length","measurements":[{"id":"side-1920","value":0.11,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard f5565b43bbb0 (AR15Discounts: the 15 in black handguard's right side, 1920 x 1280)","scaleRef":"SIDE (the file's header)","method":"the silhouette's rear end at the neck's rows (582 to 594), column 171, at the neck's depth, against the side flat's rear edge (142) at its own; what the lens's place alone would put between them is 15 px, and there are 29","via":"harvest"}},{"id":"level","value":0.17,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard 9b7983046ad2 (Aero: the 15 in Kodiak Brown handguard's right side, level, 1000 x 630)","scaleRef":"its own top rail: 37 slot centres on the Picatinny pitch from column 87 to 931, 23.44 px a pitch, 59.55 px/in; the lens stood near its rear third (its slots read widest there), so little is to be taken off at the rear end for where it stood","method":"the silhouette's rear end at the rail's floor and neck (rows 253 to 261: column 57) against the tube's rear edge (column 46): 11 px, 0.185 in, less up to 0.03 for the lens standing a few inches ahead of that end","via":"harvest"}}],"adopt":{"from":"side-1920","reason":"Decided by what it has to fit: with 0.11 its screw holes stand 0.71 and 1.12 in ahead of where it meets the receiver, and the M4E1 Enhanced receiver's platform has its own 0.72 to 0.75 and 1.12 to 1.16 ahead of its shoulder by its own photo; with 0.17 they would stand 0.06 short. The two readings are inside each other's ±."},"note":"The tube's rear end stands this far back round the receiver's front, with a notch under the rail for the receiver's own rail. Behind the first tooth the rail runs back at its slots' floor to here. What the two photos agree on to a hundredth is the rail itself, from this end: 0.50 and 0.52 in to its first slot's centre, 14.97 to its last tooth's front; how far the tube reaches behind it they read 0.06 in apart, each across two planes."},"rail_window_length":{"label":"A window through the rail (every other lug is cut through into the channel under it), along the rail","kind":"length","measurements":[{"id":"top-view","value":0.54,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard ee5fab7d8693 (Wing Tactical: a 12.63 in one from above, from its left and from below, 1280 x 1280)","scaleRef":"its own rail across, 76.7 px for the standard's 0.835 in (std.picatinny.top_width): 91.8 px/in","method":"an oblong opening's length, 48 to 50 px, over four of them","via":"harvest"}}],"note":"Aero's \"Scalloped rails\". Read on Wing's view from above of a 12.63 in one of the same page (six M-LOK slots a side): the rail's section and its windows are the family's, the count along a 15 in isn't. Which lugs: rail_window0_lug."},"rail_window_width":{"label":"That window, across the rail","kind":"length","measurements":[{"id":"top-view","value":0.36,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard ee5fab7d8693 (Wing Tactical: a 12.63 in one from above, from its left and from below, 1280 x 1280)","scaleRef":"its own rail across, 76.7 px for the standard's 0.835 in (std.picatinny.top_width): 91.8 px/in","method":"an opening's width, 33 px","via":"harvest"}}]},"rail_window0_lug":{"label":"The first lug that has a window through it, counted from the rear","kind":"count","measurements":[{"id":"top-view","value":5,"unit":"count","source":{"type":"photo","photo":"references/aero-enhanced-15-handguard ee5fab7d8693 (Wing Tactical: a 12.63 in one from above, from its left and from below, 1280 x 1280)","scaleRef":"none: a count","method":"the lugs from the rear end: whole, whole, pocket, whole, window, whole, window, ...","via":"harvest"}}],"note":"On the 12.63 in one from above: the first two lugs are whole, the third has a blind pocket (over the barrel nut), the fourth is whole, and from the fifth every other lug is cut through. The rear end is the same on every length (one nut, one hole pattern); the 15 in's own three-quarter views (23c31a17f084, 5a1039ef4a84) show its lugs cut and whole by turns to the muzzle."},"rail_windows":{"label":"How many lugs of the 15 in's 38 are cut through","kind":"count","measurements":[{"id":"derived","value":17,"unit":"count","source":{"type":"derived","expr":"({.rail_slots} - {.rail_window0_lug}) / 2 + 1","via":"harvest"}}],"note":"Worked out, not counted on a view from above of a 15 in (none is on file): every other lug from the fifth to the thirty-seventh."},"mlok_slots":{"label":"How many M-LOK slots in each side flat","kind":"count","measurements":[{"id":"photo","value":7,"unit":"count","source":{"type":"photo","photo":"references/aero-enhanced-15-handguard f5565b43bbb0 (AR15Discounts: the 15 in black handguard's right side, 1920 x 1280)","scaleRef":"SIDE (the file's header)","method":"counted along row 709: seven dark runs 135 to 138 px long (1.24 to 1.26 in: the standard's 32 mm), 171.9 px apart; behind them the sling socket's hole","via":"harvest"}}]},"mlok_slot0_from_rear":{"label":"The rearmost side M-LOK slot's centre ahead of the rear face","kind":"length","measurements":[{"id":"photo","value":4.727,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard f5565b43bbb0 (AR15Discounts: the 15 in black handguard's right side, 1920 x 1280)","scaleRef":"SIDE (the file's header): the side flat's own plane, 109.15 px/in by the slots' own pitch","method":"the first slot's centre (column 658.0; the six fit 658.0 + 171.9 k within 1 px) from the flat's rear edge (142), both on the flat","via":"harvest"}}]},"mlok_bottom_slots":{"label":"How many M-LOK slots along the bottom flat","kind":"count","measurements":[{"id":"as-the-sides","value":7,"unit":"count","source":{"type":"derived","expr":"{.mlok_slots}","via":"harvest"}}],"note":"Not seen on a 15 in: no view of its underside is on file. Wing's page says \"M-LOK slots at 3, 6, and 9 o'clock positions\", and its view from below of a 12.63 in one has along the bottom as many slots as that one has in a side (six), at the sides' stations, with the 6 o'clock socket where the sides' are. Taken so for the 15 in: its sides' own count, from the sides' first station. Where a grip or a hand stop really bolts under it may differ by a slot."},"reach_inside":{"label":"The room inside its faces, from a face in to the barrel (what an M-LOK accessory's nuts may take)","kind":"length","measurements":[],"note":"Not sourced: it depends on the barrel and gas block under it, other parts. Its wall is 0.1 in by the two published figures (1.92 wide, 1.72 inside)."},"vent_slots":{"label":"How many slots in each row of the faces between","kind":"count","measurements":[{"id":"photo","value":14,"unit":"count","source":{"type":"photo","photo":"references/aero-enhanced-15-handguard f5565b43bbb0 (AR15Discounts: the 15 in black handguard's right side, 1920 x 1280)","scaleRef":"SIDE (the file's header)","method":"counted along the upper steep face's row (row 650: thirteen dark runs, and a fourteenth at columns 1690 to 1783, seen through to the far side, which ends a tenth of an inch short of the front end) and along the row above it (row 608, the same stations); the two rows below the side flat stand at the same stations (rows 789 and 764)","via":"harvest"}}]},"vent_slot0_from_rear":{"label":"The rearmost of those slots, its centre ahead of the rear face","kind":"length","measurements":[{"id":"photo","value":2.22,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard f5565b43bbb0 (AR15Discounts: the 15 in black handguard's right side, 1920 x 1280)","scaleRef":"SIDE (the file's header)","method":"the first slot's centre in the steep face's row (column 387.5 at 0.86 in toward the lens: 2.230) and in the shallow face's (391.5 at 0.58: 2.212)","via":"harvest"}}]},"vent_slot_pitch":{"label":"Those slots' pitch along the handguard","kind":"length","measurements":[{"id":"photo","value":0.953,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard f5565b43bbb0 (AR15Discounts: the 15 in black handguard's right side, 1920 x 1280)","scaleRef":"SIDE (the file's header): 108.86 px/in at the steep face's row, 108.11 at the shallow's","method":"thirteen centres in the steep row (387.5 to 1633, 103.8 px a pitch: 0.9535) and eleven in the shallow (391.5 to 1421.5, 103.0: 0.9527)","via":"harvest"}}],"note":"Not a round figure in either system: 24 mm would be 0.945, and over the twelve pitches read it would stand 11 px short."},"vent_slot_length":{"label":"Those slots' length","kind":"length","measurements":[{"id":"photo","value":0.82,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard f5565b43bbb0 (AR15Discounts: the 15 in black handguard's right side, 1920 x 1280)","scaleRef":"SIDE (the file's header): 108.86 px/in at the steep face's row","method":"the dark runs near the lens's axis, where a slot is looked into square on: 86 to 91 px (further back its rear wall is lit and it reads short, 76 px)","via":"harvest"}}]},"vent_slot_width":{"label":"Those slots' width across their face","kind":"length","measurements":[{"id":"photo","value":0.2,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard f5565b43bbb0 (AR15Discounts: the 15 in black handguard's right side, 1920 x 1280)","scaleRef":"SIDE (the file's header): 108.4 px/in, each face seen at its own angle to the lens","method":"the steep face's row is 18 px high (rows 636 to 654) on a face whose normal is 28 degrees off the line of sight: 0.19; the shallow's is 15 px (605 to 620) at 47 degrees: 0.20","via":"harvest"}}]},"vent_steep_row_from_flat":{"label":"The steep face's row of slots, its middle up the face from the side flat's edge","kind":"length","measurements":[{"id":"photo","value":0.14,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard f5565b43bbb0 (AR15Discounts: the 15 in black handguard's right side, 1920 x 1280)","scaleRef":"SIDE (the file's header): 108.4 px/in, the face 28 degrees off the line of sight","method":"the row's dark band runs from a pixel above the flat's edge (655) to row 636: its middle 10 px up, 0.105 in, and half its lit lower wall","via":"harvest"}}]},"vent_shallow_row_from_ridge":{"label":"The shallow face's row of slots, its middle from the ridge toward the rail (or the bottom flat)","kind":"length","measurements":[{"id":"photo","value":0.17,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard f5565b43bbb0 (AR15Discounts: the 15 in black handguard's right side, 1920 x 1280)","scaleRef":"SIDE (the file's header): 108.1 px/in, the face 47 degrees off the line of sight","method":"the row's band, rows 605 to 620, is centred between the shelf's edge (598) and the ridge (621 to 624): the middle of a face 0.34 in wide","via":"harvest"}}]},"screws":{"label":"How many screws hold it to the nut or the platform","kind":"count","measurements":[{"id":"aero","value":8,"unit":"count","stated":"these handguards install effortlessly with the use of eight screws","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, Handguard Lengths (handguard_length_tech_manual_2022.pdf), page 4, Enhanced","url":"https://www.aeroprecisionusa.com/media/wysiwyg/pdf_files/handguard_length_tech_manual_2022.pdf","retrieved":"2026-10-12","via":"harvest"},"note":"Wing Tactical's box: \"8x Mounting Set Screws\". Two holes in each of the four ridges at the rear, by the side photo and the view down its length."}]},"screw_hole0_from_rear":{"label":"The rear screw holes' centres ahead of the tube's rear face","kind":"length","measurements":[{"id":"photo","value":0.824,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard f5565b43bbb0 (AR15Discounts: the 15 in black handguard's right side, 1920 x 1280)","scaleRef":"SIDE (the file's header): at the ridge's depth, 0.72 in toward the lens","method":"the upper rear hole's rim, columns 224 to 252: its middle, 238","via":"harvest"}}]},"screw_hole_spacing":{"label":"The front screw holes ahead of the rear ones","kind":"length","measurements":[{"id":"photo","value":0.41,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard f5565b43bbb0 (AR15Discounts: the 15 in black handguard's right side, 1920 x 1280)","scaleRef":"SIDE (the file's header): 108.5 px/in at the ridge","method":"the two upper holes' rims, columns 224 to 252 and 268 to 297: their middles 44.5 px apart (their dark centres, which the light skews, are 48.9 apart)","via":"harvest"}}]},"screw_countersink_d":{"label":"A screw hole's countersink, across its rim","kind":"length","measurements":[{"id":"photo","value":0.27,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard f5565b43bbb0 (AR15Discounts: the 15 in black handguard's right side, 1920 x 1280)","scaleRef":"SIDE (the file's header): 108.5 px/in at the ridge","method":"the two upper holes along the handguard, where a round rim isn't foreshortened: 28 and 30 px","via":"harvest"}}]},"screw_hole_d":{"label":"A screw hole, across (the screw's thread)","kind":"length","measurements":[{"id":"kit-photo","value":0.14,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard a3dd964e9ad5 (Wing Tactical: the BAR nut, its shims and the eight flat-head screws laid out, 1280 x 1280)","scaleRef":"each screw's own head, taken at screw_countersink_d","method":"a screw's thread is about half its head across, on the four that lie side on","via":"harvest"}}],"note":"No page names the screw. Read as a share of its head on the seller's photo of the eight laid out, and good to no more than that."},"socket_from_rear":{"label":"The sling sockets' centres ahead of the rear face (3, 6 and 9 o'clock, at one station)","kind":"length","measurements":[{"id":"photo","value":2.863,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard f5565b43bbb0 (AR15Discounts: the 15 in black handguard's right side, 1920 x 1280)","scaleRef":"SIDE (the file's header): the side flat's own plane, 109.15 px/in","method":"the right socket's dark hole, centred on column 454.5 and on the M-LOK row","via":"harvest"}}],"note":"Aero: \"Quick disconnect sling socket at the 3, 6 and 9 o'clock positions\". The one at 6 o'clock is a steel cup under the bottom edge, with its own figures (socket_cup_from_rear)."},"socket_hole_d":{"label":"A sling socket's hole, across","kind":"length","measurements":[{"id":"photo","value":0.36,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard f5565b43bbb0 (AR15Discounts: the 15 in black handguard's right side, 1920 x 1280)","scaleRef":"SIDE (the file's header): the side flat's own plane, 109.15 px/in","method":"the dark hole, 38 to 40 px across and as high","via":"harvest"}}]},"socket_boss_d":{"label":"The boss a sling socket stands in, across","kind":"length","measurements":[{"id":"photo","value":0.67,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard f5565b43bbb0 (AR15Discounts: the 15 in black handguard's right side, 1920 x 1280)","scaleRef":"SIDE (the file's header): the side flat's own plane, 109.15 px/in","method":"the lit ring round the right socket's hole, 73 px across","via":"harvest"}}]},"socket_boss_height":{"label":"How far a side sling socket's boss stands off its flat","kind":"length","measurements":[{"id":"top-view","value":0.087,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard ee5fab7d8693 (Wing Tactical: a 12.63 in one from above, from its left and from below, 1280 x 1280)","scaleRef":"its own rail across, 76.7 px for the standard's 0.835 in (std.picatinny.top_width): 91.8 px/in","method":"the bump at each side of the silhouette at the sockets' station, 8 px proud of the side flat","via":"harvest"}}],"note":"Read on a 12.63 in one seen from above (the sockets are the family's: Aero's \"Quick disconnect sling socket at the 3, 6 and 9 o'clock positions\" is said of every length); no view of a 15 in from above is on file."},"socket_cup_d":{"label":"The sling socket at 6 o'clock: its steel cup, across","kind":"length","measurements":[{"id":"level","value":0.484,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard 9b7983046ad2 (Aero: the 15 in Kodiak Brown handguard's right side, level, 1000 x 630)","scaleRef":"its traced outline (profiles.side), scaled by its length end to end (overall_length): 59.97 px/in","method":"the cup's two ends under the bottom edge, 2.676 and 3.160 in from the rear face","via":"harvest"}}],"note":"A piece of its own: black under the Kodiak Brown, the OD Green and the FDE handguards in Aero's photos of each, where the two side sockets are the handguard's own metal and colour."},"socket_cup_from_rear":{"label":"That cup's middle ahead of the tube's rear face","kind":"length","measurements":[{"id":"level","value":2.918,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard 9b7983046ad2 (Aero: the 15 in Kodiak Brown handguard's right side, level, 1000 x 630)","scaleRef":"its traced outline (profiles.side), scaled by its length end to end (overall_length): 59.97 px/in","method":"the middle of the cup's two ends, 2.676 and 3.160","via":"harvest"},"note":"The larger side photo has its middle 2.90 in from the rear face; the side sockets' holes stand at 2.863 (socket_from_rear)."}]},"socket_cup_height":{"label":"How far that cup stands below the bottom flat","kind":"length","measurements":[{"id":"level","value":0.084,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard 9b7983046ad2 (Aero: the 15 in Kodiak Brown handguard's right side, level, 1000 x 630)","scaleRef":"its traced outline (profiles.side), scaled by its length end to end (overall_length): 59.97 px/in","method":"the cup's underside 2.268 below the rail's top against the bottom edge's 2.184","via":"harvest"}},{"id":"side-1920","value":0.055,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard f5565b43bbb0 (AR15Discounts: the 15 in black handguard's right side, 1920 x 1280)","scaleRef":"SIDE (the file's header): 107 px/in at the bottom's middle","method":"the cup below the bottom edge, rows 800 to 806, seen from 9 degrees above (the bottom flat's near corner hides some of it)","via":"harvest"}}],"adopt":{"from":"level","reason":"The level view; from above the bottom's near edge hides part of what stands under its middle."}},"rear_bottom_ahead":{"label":"The bottom flat's rear end ahead of the tube's rear face (its rear end leans forward below the side flats' upper edges)","kind":"length","measurements":[{"id":"level","value":0.235,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard 9b7983046ad2 (Aero: the 15 in Kodiak Brown handguard's right side, level, 1000 x 630)","scaleRef":"its own top rail: 37 slot centres on the Picatinny pitch from column 87 to 931, 23.44 px a pitch, 59.55 px/in; the lens stood near its rear third (its slots read widest there), so little is to be taken off at the rear end for where it stood","method":"the silhouette's rear edge at the bottom corner (rows 369 to 373: column 60) against its rear edge above the side flat (rows 265 to 273: column 46): 14 px","via":"harvest"}},{"id":"side-1920","value":0.29,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard f5565b43bbb0 (AR15Discounts: the 15 in black handguard's right side, 1920 x 1280)","scaleRef":"SIDE (the file's header)","method":"the bottom edge reaches its level from column 186 (luminance under 120); a square end at the bottom flat's near corner, 0.44 in out, would show at column 155","via":"harvest"}}],"adopt":{"from":"level","reason":"Read near its lens's axis, with nothing to take off for where the lens stood; the larger photo's reading, which has 13 px of that taken off, is 0.055 in more, inside the two ±."},"note":"The tube's rear end isn't square below the side flats' upper edges. Aero's level photo, taken from near that end, has its edge 0.12 in forward at the side flat's lower edge, 0.15 at the lower ridge and 0.235 at the bottom flat; AR15Discounts' larger one, against where a square end would show from its lens, 0.14, 0.18 and 0.29. The receiver's pivot lug stands under there. Drawn as one plane from the side flats' upper edges to this figure at the bottom flat (up to 0.04 in ahead of the readings between)."},"scallop_pitch":{"label":"The scallops milled along the side flats' two edges: their pitch (not drawn)","kind":"length","measurements":[{"id":"photo","value":0.527,"unit":"in","pm":0.003,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard f5565b43bbb0 (AR15Discounts: the 15 in black handguard's right side, 1920 x 1280)","scaleRef":"SIDE (the file's header): the side flat's own plane, 109.15 px/in","method":"bright ticks along rows 660 to 664 and 744 to 752: twenty of them from column 188 to 1394 at 57.55 px (two not found, at the sling socket and near 1452)","via":"harvest"}}],"note":"Aero: \"Additional milling along flats to aid with gripping and add visual appeal\". Small crescent cuts, about a tenth of an inch long, in a row along each edge of a side flat (and of the bottom flat, by Wing's view of a 12.63 in one from below). Read so that a later pass can cut them; the model leaves them out."},"scallop0_from_rear":{"label":"The rearmost of those scallops ahead of the tube's rear face (not drawn)","kind":"length","measurements":[{"id":"photo","value":0.42,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard f5565b43bbb0 (AR15Discounts: the 15 in black handguard's right side, 1920 x 1280)","scaleRef":"SIDE (the file's header): the side flat's own plane, 109.15 px/in","method":"the first tick at column 188 (upper edge) and 186 (lower edge), from the flat's rear edge at 142","via":"harvest"}}]},"bottom_below_bore":{"label":"The bottom flat below the bore axis","kind":"length","measurements":[{"id":"derived","value":0.9675,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{.height} - {.rail_top_above_bore}","via":"harvest"}}],"note":"The seller's height less the rail's height above the bore; half the seller's width is 0.96."},"shelf_below_rail_top":{"label":"The tube's top beside the rail's neck (the shelf the neck stands on), below the rail's top","kind":"length","measurements":[{"id":"level","value":0.235,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard 9b7983046ad2 (Aero: the 15 in Kodiak Brown handguard's right side, level, 1000 x 630)","scaleRef":"its own top rail: 37 slot centres on the Picatinny pitch, 59.55 px/in; a level view (each row of openings is seen through at one height on both sides)","method":"the shadow under the rail's head and down its neck ends between rows 258 and 259, 13.5 to 14 px below the teeth's tops (row 245); ± is a row","via":"harvest"}},{"id":"side-1920","value":0.237,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard f5565b43bbb0 (AR15Discounts: the 15 in black handguard's right side, 1920 x 1280)","scaleRef":"SIDE (the file's header): 107 px/in, the lens 9 degrees above level","method":"the tube's top edge at row 598, 38 px below the rail's top (560), less what the lens's height adds between the rail's far top edge and the shelf's near corner (13 px)","via":"harvest"}},{"id":"mirror","value":0.245,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"2 * {.rail_top_above_bore} - {.height}","via":"harvest"},"note":"What it would be if the tube's top were as far above the bore as its bottom flat is below it."}],"adopt":{"from":"level","reason":"The level view's own reading; the larger photo and the tube taken as high as it is deep agree within a hundredth."},"note":"How much room a clamp's jaws have under the rail's head. Short: Aero's R-ONE has its neck's foot 0.38 in below its rail's top (aero-r-one-15-handguard.rail_neck_foot_below_rail_top), and three clamps on file whose hooks reach 0.37 to 0.39 in below a rail's top (Aimpoint's Micro T-2 mount, EOTECH's G33 and G45 mounts) stand in this tube's top as drawn. Further out the tube's top falls away: where the tube's rear rim begins behind the rail it is 0.29 to 0.30 below the rail's top on the level photo."},"rear_notch_width":{"label":"The notch under the rail at the tube's rear end (what the receiver's own rail and the body under it stand in), across","kind":"length","measurements":[{"id":"level","value":1.05,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/aero-enhanced-15-handguard 9b7983046ad2 (Aero: the 15 in Kodiak Brown handguard's right side, level, 1000 x 630)","scaleRef":"its own top rail: 37 slot centres on the Picatinny pitch, 59.55 px/in; a level view","method":"the silhouette's rear end steps back from the rail's (column 57) to the tube's (46 to 47) between rows 262 and 263, 17.5 px (0.294 in) below the teeth's tops; carried onto the upper shallow face as the section has it (from 0.44 in out at shelf_below_rail_top to the ridge)","via":"harvest"}}],"note":"Not seen square on. From the side the tube's rear rim begins 0.29 to 0.30 in below the rail's top, lower than the tube's top beside the neck (shelf_below_rail_top): the rim's highest point is where the notch's side cuts the shallow face, and on the face as drawn that height is 0.525 in out from the middle. As good as the face's own angle (a few degrees): 0.06 in either way. The receiver's rail, 0.835 across, has to pass through it."}}},{"subject":"aero-m4e1-enhanced-upper","title":"Aero Precision M4E1 Enhanced Upper Receiver, stripped (APAR600201C)","dimensions":{"weight":{"label":"Weight (the stripped receiver: no port door, forward assist, barrel nut or barrel)","kind":"mass","measurements":[{"id":"worked-out","value":9.99,"unit":"oz","pm":1,"source":{"type":"derived","expr":"{.weight_as_metal}","via":"harvest"},"note":"WORKED OUT, not published (2026-10-12, the orchestrator's call: a piece no page gives a weight for is weighed by its own metal, with a ± and said as that, so a build with it has a total): Aero's 6.9 oz for the M4E1 Threaded stripped receiver plus the platform's ring as 7075 (weight_as_metal has the sum and what it leaves out). A page that states the stripped receiver's weight replaces it."}],"note":"No page states it. Aero's specifications for APAR600201C say \"Weight(s) -\". AR15Discounts' page for the blemished one (APAR600201BC) says \"Weight: 12 oz\" beside \"Dimensions: 10.6\\u2033 L x 2.6\\u2033 W x 3.9\\u2033 H\", a carton's (weight_listed). Aero's assembled M4E1 Enhanced upper without a forward assist (APAR612201AC), with its port door and its barrel nut, is 11.28 oz: another product's. What its own metal would come to is weight_as_metal (about 10 oz), worked out and not adopted here."},"weight_listed":{"label":"A seller's weight for the blemished stripped receiver's listing (not this number's; beside a carton's dimensions)","kind":"mass","measurements":[{"id":"ar15discounts","value":12,"unit":"oz","pm":0.5,"stated":"Weight: 12 oz","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, APAR600201BC - Aero Precision M4E1 Enhanced Stripped Upper Receiver - Anodized Black - BLEM, Specifications","url":"https://ar15discounts.com/products/aero-precision-m4e1-enhanced-stripped-upper-receiver-anodized-black-blem/","retrieved":"2026-10-12","via":"harvest"},"note":"The same page: \"Dimensions: 10.6″ L x 2.6″ W x 3.9″ H\", longer than the receiver: the listing's shipping figures. Kept as what a page says, and not the part's weight."}]},"weight_as_metal":{"label":"What the stripped receiver would weigh by its own metal: the M4E1 Threaded receiver's published weight and the platform","kind":"mass","measurements":[{"id":"worked-out","value":9.99,"unit":"oz","pm":1,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.weight} + 0.785398163 * (({.platform_od} * {.platform_od} - {.platform_bore_d} * {.platform_bore_d}) * ({.platform_front_x} - {.front_face_x}) + ({.platform_od} * {.platform_od} - {.bore_d} * {.bore_d}) * ({.front_face_x} - {.shoulder_x})) * {std.density.aluminium_7075}","via":"harvest"}}],"note":"Worked out, and not the part's weight (no page gives one): Aero's 6.9 oz for the M4E1 Threaded stripped receiver plus the platform as a ring of 7075 (Aero: \"Machined from 7075-T6 forged aluminum\") of its read sizes, solid over the bore from the shoulder to the barrel's seat and bored for the nut ahead of it. The Threaded receiver's own barrel-nut thread (about a third of an ounce) isn't taken off, nor the platform's grooves and screw holes, and the two forgings may differ elsewhere: good to an ounce. Aero's assembled M4E1 Enhanced upper without a forward assist (APAR612201AC), with a port door and a barrel nut on it, is 11.28 oz."},"bore_axis_above_pin":{"label":"Bore axis above the takedown pin centre","kind":"length","measurements":[{"id":"standard","value":0.8775,"unit":"in","pm":0.0015,"source":{"type":"derived","expr":"{std.ar15.bore_axis_y}","via":"harvest"},"note":"The standard's: Aero's page says it \"Works with standard AR15/M16 components\". This receiver's own platform is centred 0.875 above its pin line on its photo (platform_od)."}]},"rail_top_above_pin":{"label":"The top rail's surface above the pin line","kind":"length","measurements":[{"id":"right","value":2.088,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-m4e1-enhanced-upper 841632838fda (AR15Discounts 324831.png: the M4E1 Enhanced stripped upper's right side, straight on, 1920 x 1280; the same picture as Aero's own of APAR600201C)","scaleRef":"its own takedown and pivot lug holes as the pins (centres at px 292.09, 835.76 and 1463.51, 836.85), std.ar15.pin_spacing apart: 183.75 px/in, tilt 0.05 degrees; its rail's 14 slots fit the standard pitch to 0.1% in that frame","method":"the rail's tooth tops (the silhouette's highest, rows 452 to 456) above the line through the two holes; ± is two pixels and a row","via":"harvest"}},{"id":"threaded","value":2.09,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.rail_top_above_pin}","via":"harvest"},"note":"The sibling forging's, read on two photos of its own (corroborated there)."}],"adopt":{"from":"threaded","reason":"The same forging family's rail, read twice on the Threaded receiver; this receiver's one reading agrees within a tenth of its ±, and its body's heights are the Threaded one's, counted from that figure."},"note":"The Threaded receiver's figure is adopted (2026-10-12, at integration): this receiver's own photo reads 2.088, a tenth of its ± under the 2.09 that two photos give the Threaded one; its body under the slots' floors is built on the Threaded receiver's heights (the dovetail's foot, the neck), which are counted from that 2.09, and with the rail's top two thousandths lower the head's lower faces came out 0.0008 in narrow; and its own handguard's rail is level with a receiver's at 2.09 (Aero: \"blends seamlessly\")."},"rail_slot0_x":{"label":"The rearmost rail slot's centre ahead of the takedown pin","kind":"length","measurements":[{"id":"photo","value":1.178,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/aero-m4e1-enhanced-upper 841632838fda (AR15Discounts 324831.png: the M4E1 Enhanced stripped upper's right side, straight on, 1920 x 1280; the same picture as Aero's own of APAR600201C)","scaleRef":"its own takedown and pivot lug holes as the pins (centres at px 292.09, 835.76 and 1463.51, 836.85), std.ar15.pin_spacing apart: 183.75 px/in, tilt 0.05 degrees; its rail's 14 slots fit the standard pitch to 0.1% in that frame","method":"the top edge's 14 slot floors (their edges at 1.086 and 1.271, ... 6.207 and 6.392): the centres fitted to the standard pitch, 0.3940 in apart","via":"harvest"}}]},"rail_slots":{"label":"How many rail slots","kind":"count","measurements":[{"id":"photo","value":14,"unit":"count","source":{"type":"photo","photo":"references/aero-m4e1-enhanced-upper 841632838fda (AR15Discounts 324831.png: the M4E1 Enhanced stripped upper's right side, straight on, 1920 x 1280; the same picture as Aero's own of APAR600201C)","scaleRef":"its own takedown and pivot lug holes as the pins (centres at px 292.09, 835.76 and 1463.51, 836.85), std.ar15.pin_spacing apart: 183.75 px/in, tilt 0.05 degrees; its rail's 14 slots fit the standard pitch to 0.1% in that frame","method":"counted along the top edge","via":"harvest"}}],"note":"Behind the first is a solid run of rail over the charging handle's channel (from rail_rear_x); the last tooth ends at the shoulder."},"rail_rear_x":{"label":"The top rail's head: where it begins ahead of the tongue, X (the app draws the head from here)","kind":"length","measurements":[{"id":"standard","value":0.4165,"unit":"in","pm":0.006,"source":{"type":"derived","expr":"{std.ar15.rail_tongue_shoulder_x}","via":"user"}}],"note":"Until 2026-10-20 this was the rail's rearmost point (now rail_tongue_rear_x), and the app drew the head at its full width from there, square: the charging handle's T, cut round for a rounded rail end, stood in its corners. Behind this the rail is the standard's tongue (std.ar15.rail_tongue_*), which the receiver's model carries, as the 22RB's does."},"rail_tongue_rear_x":{"label":"The top rail's tongue: its rounded end's rearmost point, X ahead of the takedown pin","kind":"length","measurements":[{"id":"photo","value":-0.6,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/aero-m4e1-enhanced-upper 841632838fda (AR15Discounts 324831.png: the M4E1 Enhanced stripped upper's right side, straight on, 1920 x 1280; the same picture as Aero's own of APAR600201C)","scaleRef":"its own takedown and pivot lug holes as the pins (centres at px 292.09, 835.76 and 1463.51, 836.85), std.ar15.pin_spacing apart: 183.75 px/in, tilt 0.05 degrees; its rail's 14 slots fit the standard pitch to 0.1% in that frame","method":"where the top edge first reaches the teeth's height, column 182","via":"harvest"}}]},"rail_front_x":{"label":"The top rail's front end ahead of the takedown pin","kind":"length","measurements":[{"id":"shoulder","value":6.591,"unit":"in","pm":0.011,"source":{"type":"derived","expr":"{.shoulder_x}","via":"harvest"}},{"id":"photo","value":6.599,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/aero-m4e1-enhanced-upper 841632838fda (AR15Discounts 324831.png: the M4E1 Enhanced stripped upper's right side, straight on, 1920 x 1280; the same picture as Aero's own of APAR600201C)","scaleRef":"its own takedown and pivot lug holes as the pins (centres at px 292.09, 835.76 and 1463.51, 836.85), std.ar15.pin_spacing apart: 183.75 px/in, tilt 0.05 degrees; its rail's 14 slots fit the standard pitch to 0.1% in that frame","method":"the last tooth's front, columns 1505 to 1506: the receiver body's front shoulder, where the top drops to the platform","via":"harvest"}}],"adopt":{"from":"shoulder","reason":"One face with the shoulder, which is taken at the standard's place; the photo reads the last tooth's front 0.008 in ahead of it, inside its ±."},"note":"The rail ends on the receiver body's front shoulder: one face, where an Enhanced handguard's own rail meets it and carries on. Ahead of it is the platform, lower."},"receiver_rear_x":{"label":"The receiver's rear face behind the takedown pin (negative)","kind":"length","measurements":[{"id":"standard","value":-0.621,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.ar15.upper_rear_face_x}","via":"harvest"},"note":"The Army's drawing of the upper (8448524): Aero's \"Works with standard AR15/M16 components\"."},{"id":"right","value":-0.654,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/aero-m4e1-enhanced-upper 841632838fda (AR15Discounts 324831.png: the M4E1 Enhanced stripped upper's right side, straight on, 1920 x 1280; the same picture as Aero's own of APAR600201C)","scaleRef":"its own takedown and pivot lug holes as the pins (centres at px 292.09, 835.76 and 1463.51, 836.85), std.ar15.pin_spacing apart: 183.75 px/in, tilt 0.05 degrees; its rail's 14 slots fit the standard pitch to 0.1% in that frame","method":"the silhouette's rear end behind the takedown hole's centre, column 172; ± is two pixels and what a near edge reads long","via":"harvest"}}],"adopt":{"from":"standard","reason":"The drawing dimensions the face; the photo reads 0.03 in more, as a silhouette's near edge does (the M4E1 Threaded receiver's two photos read 0.02 more)."}},"front_face_x":{"label":"Where a barrel extension's flange seats, inside the platform, ahead of the takedown pin","kind":"length","measurements":[{"id":"standard","value":7.036,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.ar15.upper_front_face_x}","via":"harvest"},"note":"The Army's drawing puts a receiver's front face (the end of its barrel-nut thread, where the flange seats) .661 ahead of the pivot lug's hole. This receiver has no such thread; the barrel still has to stand where the standard's bolt carrier and magazine meet it (Aero: \"Works with standard AR15/M16 components\", \"M4 Feedramps\"), so the seat is taken at the standard's place. It is inside the platform and in no photo on file."}]},"shoulder_x":{"label":"The receiver body's front shoulder, where the platform begins and a handguard's rail meets the receiver's, ahead of the takedown pin","kind":"length","measurements":[{"id":"standard","value":6.591,"unit":"in","pm":0.011,"source":{"type":"derived","expr":"{std.ar15.upper_front_face_x} - {std.ar15.upper_barrel_thread_length}","via":"harvest"},"note":"Where a mil-spec receiver's body ends and its barrel-nut thread begins (the Army's .445 REF behind its front face)."},{"id":"right","value":6.597,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/aero-m4e1-enhanced-upper 841632838fda (AR15Discounts 324831.png: the M4E1 Enhanced stripped upper's right side, straight on, 1920 x 1280; the same picture as Aero's own of APAR600201C)","scaleRef":"its own takedown and pivot lug holes as the pins (centres at px 292.09, 835.76 and 1463.51, 836.85), std.ar15.pin_spacing apart: 183.75 px/in, tilt 0.05 degrees; its rail's 14 slots fit the standard pitch to 0.1% in that frame","method":"the body's front face above the platform (rows 452 to 508: columns 1503 to 1505) and below it (rows 844 to 852: 1503 to 1504); ± is two pixels","via":"harvest"}}],"adopt":{"from":"standard","reason":"The standard's place for it, which the handguard and the BAR nut are made to; this receiver's own photo reads 0.006 in more, inside its ±."},"note":"This receiver's own photo has its shoulder where the standard's is, within a pixel: Aero's BAR barrel nut puts the same platform on a standard receiver from that shoulder forward, and one handguard goes on both."},"underside_y":{"label":"The receiver's underside above the pin line","kind":"length","measurements":[{"id":"standard","value":0.2485,"unit":"in","pm":0.0015,"source":{"type":"derived","expr":"{std.ar15.deck_y}","via":"harvest"},"note":"It sits on the lower's deck."}]},"platform_front_x":{"label":"The platform's front face ahead of the takedown pin","kind":"length","measurements":[{"id":"right","value":7.925,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-m4e1-enhanced-upper 841632838fda (AR15Discounts 324831.png: the M4E1 Enhanced stripped upper's right side, straight on, 1920 x 1280; the same picture as Aero's own of APAR600201C)","scaleRef":"its own takedown and pivot lug holes as the pins (centres at px 292.09, 835.76 and 1463.51, 836.85), std.ar15.pin_spacing apart: 183.75 px/in, tilt 0.05 degrees; its rail's 14 slots fit the standard pitch to 0.1% in that frame","method":"the silhouette's front between the barrel nut's lugs (rows 600 to 608, 660 to 692, 748 to 752: columns 1748 to 1751)","via":"harvest"}}],"note":"1.33 in ahead of the shoulder. In this picture a barrel nut stands in it, its lugs a tenth of an inch proud of the face (to 8.03); Aero's page for this number: \"NOTE: This Upper Receiver will NOT ship with a barrel nut.\""},"platform_od":{"label":"The platform's diameter (what an Enhanced handguard's barrel nut cut goes over)","kind":"length","measurements":[{"id":"right","value":1.77,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-m4e1-enhanced-upper 841632838fda (AR15Discounts 324831.png: the M4E1 Enhanced stripped upper's right side, straight on, 1920 x 1280; the same picture as Aero's own of APAR600201C)","scaleRef":"its own takedown and pivot lug holes as the pins (centres at px 292.09, 835.76 and 1463.51, 836.85), std.ar15.pin_spacing apart: 183.75 px/in, tilt 0.05 degrees; its rail's 14 slots fit the standard pitch to 0.1% in that frame","method":"its top (the tops of the teeth between its grooves, rows 511 to 513: 1.768 to 1.774 above the pin line) to its bottom edge (rows 833 to 840 along it: 0.02 above the pin line at its front, 0.02 below at its rear); its middle 0.875 above the pin line, the bore's 0.8775","via":"harvest"}}],"note":"Round about the bore. Aero's handguard for it is bored 1.78 in there (aero-enhanced-15-handguard.nut_cut_diameter): this reading is a hundredth under that."},"platform_bore_d":{"label":"The platform's bore at its front, where the barrel nut goes in","kind":"length","measurements":[{"id":"right","value":1.22,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/aero-m4e1-enhanced-upper 841632838fda (AR15Discounts 324831.png: the M4E1 Enhanced stripped upper's right side, straight on, 1920 x 1280; the same picture as Aero's own of APAR600201C)","scaleRef":"its own takedown and pivot lug holes as the pins (centres at px 292.09, 835.76 and 1463.51, 836.85), std.ar15.pin_spacing apart: 183.75 px/in, tilt 0.05 degrees; its rail's 14 slots fit the standard pitch to 0.1% in that frame","method":"the barrel nut's lugs standing out of the front face, from 0.61 above the bore's axis (row 564) to 0.61 below it (row 788)","via":"harvest"}}],"note":"Read from the barrel nut in the picture, which this number doesn't ship with: the nut's outside, and so the least the bore can be. Its thread isn't drawn."},"platform_grooves":{"label":"How many grooves are cut across the top of the platform","kind":"count","measurements":[{"id":"right","value":6,"unit":"count","source":{"type":"photo","photo":"references/aero-m4e1-enhanced-upper 841632838fda (AR15Discounts 324831.png: the M4E1 Enhanced stripped upper's right side, straight on, 1920 x 1280; the same picture as Aero's own of APAR600201C)","scaleRef":"its own takedown and pivot lug holes as the pins (centres at px 292.09, 835.76 and 1463.51, 836.85), std.ar15.pin_spacing apart: 183.75 px/in, tilt 0.05 degrees; its rail's 14 slots fit the standard pitch to 0.1% in that frame","method":"counted along the top edge between the shoulder and the front face","via":"harvest"}}]},"platform_groove0_x":{"label":"The rearmost of those grooves, its middle ahead of the takedown pin","kind":"length","measurements":[{"id":"right","value":6.722,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/aero-m4e1-enhanced-upper 841632838fda (AR15Discounts 324831.png: the M4E1 Enhanced stripped upper's right side, straight on, 1920 x 1280; the same picture as Aero's own of APAR600201C)","scaleRef":"its own takedown and pivot lug holes as the pins (centres at px 292.09, 835.76 and 1463.51, 836.85), std.ar15.pin_spacing apart: 183.75 px/in, tilt 0.05 degrees; its rail's 14 slots fit the standard pitch to 0.1% in that frame","method":"its two walls at 6.670 and 6.773 (columns 1518 and 1537)","via":"harvest"}}]},"platform_groove_pitch":{"label":"Those grooves' pitch","kind":"length","measurements":[{"id":"right","value":0.2016,"unit":"in","pm":0.003,"source":{"type":"photo","photo":"references/aero-m4e1-enhanced-upper 841632838fda (AR15Discounts 324831.png: the M4E1 Enhanced stripped upper's right side, straight on, 1920 x 1280; the same picture as Aero's own of APAR600201C)","scaleRef":"its own takedown and pivot lug holes as the pins (centres at px 292.09, 835.76 and 1463.51, 836.85), std.ar15.pin_spacing apart: 183.75 px/in, tilt 0.05 degrees; its rail's 14 slots fit the standard pitch to 0.1% in that frame","method":"six grooves' middles, 6.722 to 7.729","via":"harvest"}}]},"platform_groove_width":{"label":"Those grooves' width along the platform","kind":"length","measurements":[{"id":"right","value":0.1,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/aero-m4e1-enhanced-upper 841632838fda (AR15Discounts 324831.png: the M4E1 Enhanced stripped upper's right side, straight on, 1920 x 1280; the same picture as Aero's own of APAR600201C)","scaleRef":"its own takedown and pivot lug holes as the pins (centres at px 292.09, 835.76 and 1463.51, 836.85), std.ar15.pin_spacing apart: 183.75 px/in, tilt 0.05 degrees; its rail's 14 slots fit the standard pitch to 0.1% in that frame","method":"each groove's two walls: 0.093 to 0.104","via":"harvest"}}]},"platform_groove_depth":{"label":"Those grooves' depth below the platform's top","kind":"length","measurements":[{"id":"right","value":0.125,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aero-m4e1-enhanced-upper 841632838fda (AR15Discounts 324831.png: the M4E1 Enhanced stripped upper's right side, straight on, 1920 x 1280; the same picture as Aero's own of APAR600201C)","scaleRef":"its own takedown and pivot lug holes as the pins (centres at px 292.09, 835.76 and 1463.51, 836.85), std.ar15.pin_spacing apart: 183.75 px/in, tilt 0.05 degrees; its rail's 14 slots fit the standard pitch to 0.1% in that frame","method":"their floors at 1.643 to 1.649 above the pin line against the teeth's tops at 1.768 to 1.774","via":"harvest"}}]},"platform_hole0_x":{"label":"The platform's rear screw holes, their centres ahead of the takedown pin","kind":"length","measurements":[{"id":"right","value":7.341,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aero-m4e1-enhanced-upper 841632838fda (AR15Discounts 324831.png: the M4E1 Enhanced stripped upper's right side, straight on, 1920 x 1280; the same picture as Aero's own of APAR600201C)","scaleRef":"its own takedown and pivot lug holes as the pins (centres at px 292.09, 835.76 and 1463.51, 836.85), std.ar15.pin_spacing apart: 183.75 px/in, tilt 0.05 degrees; its rail's 14 slots fit the standard pitch to 0.1% in that frame","method":"the two rear holes' dark centres, the upper at column 1640.1 and the lower at 1641.7","via":"harvest"}}],"note":"0.75 ahead of the shoulder; an Enhanced handguard's own rear screw holes stand 0.71 ahead of where its rail meets the receiver, by its own photo."},"platform_hole_spacing":{"label":"The front screw holes ahead of the rear ones","kind":"length","measurements":[{"id":"right","value":0.414,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/aero-m4e1-enhanced-upper 841632838fda (AR15Discounts 324831.png: the M4E1 Enhanced stripped upper's right side, straight on, 1920 x 1280; the same picture as Aero's own of APAR600201C)","scaleRef":"its own takedown and pivot lug holes as the pins (centres at px 292.09, 835.76 and 1463.51, 836.85), std.ar15.pin_spacing apart: 183.75 px/in, tilt 0.05 degrees; its rail's 14 slots fit the standard pitch to 0.1% in that frame","method":"the upper pair's dark centres 75.2 px apart, the lower pair's 77.0","via":"harvest"}}]},"platform_hole_above_bore":{"label":"The upper screw holes above the bore's level (and the lower ones below it)","kind":"length","measurements":[{"id":"right","value":0.6155,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aero-m4e1-enhanced-upper 841632838fda (AR15Discounts 324831.png: the M4E1 Enhanced stripped upper's right side, straight on, 1920 x 1280; the same picture as Aero's own of APAR600201C)","scaleRef":"its own takedown and pivot lug holes as the pins (centres at px 292.09, 835.76 and 1463.51, 836.85), std.ar15.pin_spacing apart: 183.75 px/in, tilt 0.05 degrees; its rail's 14 slots fit the standard pitch to 0.1% in that frame","method":"the upper pair's centres at row 562.8, 1.493 above the pin line; the lower pair's at about row 791 (0.25), seen from further round","via":"harvest"}}],"note":"On a round of this diameter that is 44 degrees up from the bore's level: the eight holes stand at the four diagonals, two along each."},"platform_hole_d":{"label":"A screw hole in the platform, across","kind":"length","measurements":[{"id":"right","value":0.1,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-m4e1-enhanced-upper 841632838fda (AR15Discounts 324831.png: the M4E1 Enhanced stripped upper's right side, straight on, 1920 x 1280; the same picture as Aero's own of APAR600201C)","scaleRef":"its own takedown and pivot lug holes as the pins (centres at px 292.09, 835.76 and 1463.51, 836.85), std.ar15.pin_spacing apart: 183.75 px/in, tilt 0.05 degrees; its rail's 14 slots fit the standard pitch to 0.1% in that frame","method":"the upper holes' dark openings, 16 px along the platform (0.087); the lower pair's 18 to 22","via":"harvest"}}]},"platform_holes":{"label":"How many screw holes the platform has","kind":"count","measurements":[{"id":"aero","value":8,"unit":"count","stated":"we have condensed the parts needed to mount a free-floated handguard to a mere 8 screws","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, M4E1 Enhanced Upper Receiver Stripped - Anodized Black (APAR600201C), Details","url":"https://www.aeroprecisionusa.com/ar15-m4e1-enhanced-upper-receiver-stripped","retrieved":"2026-10-12","via":"harvest"},"note":"Four show on its right side, two above and two below; the left side's four are in Aero's views of the assembled one."}]},"width":{"label":"Width of the receiver's body","kind":"length","measurements":[{"id":"threaded","value":1.18,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.width}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder (this file's header)."}]},"charging_handle_above_bore":{"label":"The charging handle's channel above the bore's axis","kind":"length","measurements":[{"id":"threaded","value":0.8563,"unit":"in","pm":0.007,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.charging_handle_above_bore}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder (this file's header)."}]},"handle_seat_x":{"label":"The charging handle's seat: the front wall of the open notch under the rail's rear end, ahead of the takedown pin","kind":"length","measurements":[{"id":"threaded","value":0.092,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.handle_seat_x}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder (this file's header)."}]},"body_radius":{"label":"The round body's radius about the bore (the forging's)","kind":"length","measurements":[{"id":"threaded","value":0.59,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.body_radius}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder (this file's header)."}]},"bore_d":{"label":"The bore the bolt carrier runs in","kind":"length","measurements":[{"id":"threaded","value":1,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.bore_d}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder (this file's header)."}]},"dovetail_foot_y":{"label":"The rail's dovetail, its foot (where the neck begins), Y above the pin line","kind":"length","measurements":[{"id":"threaded","value":1.885,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.dovetail_foot_y}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder (this file's header)."}]},"dovetail_foot_half_width":{"label":"The rail's dovetail at its foot, half its width","kind":"length","measurements":[{"id":"threaded","value":0.323,"unit":"in","pm":0.013,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.dovetail_foot_half_width}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder (this file's header)."}]},"rail_neck_half_width":{"label":"The rail's neck below its dovetail, half its width","kind":"length","measurements":[{"id":"threaded","value":0.309,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.rail_neck_half_width}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder (this file's header)."}]},"rail_neck_bottom_y":{"label":"The rail's neck, where it meets the body below it, Y","kind":"length","measurements":[{"id":"threaded","value":1.737,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.rail_neck_bottom_y}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder (this file's header)."}]},"side_half_width":{"label":"The body's upper sides, below the rail's neck: half the width across them","kind":"length","measurements":[{"id":"threaded","value":0.42,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.side_half_width}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder (this file's header)."}]},"side_bottom_y":{"label":"The body's upper sides, their lower edge (where the face that slopes out begins), Y","kind":"length","measurements":[{"id":"threaded","value":1.435,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.side_bottom_y}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder (this file's header)."}]},"shoulder_bottom_y":{"label":"The sloped faces' lower edge, where the body is widest, Y","kind":"length","measurements":[{"id":"threaded","value":0.875,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.shoulder_bottom_y}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder (this file's header)."}]},"lug_wall_half_width":{"label":"The walls below the round body down to the underside, half the width","kind":"length","measurements":[{"id":"threaded","value":0.453,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.lug_wall_half_width}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder (this file's header)."}]},"port_length":{"label":"The ejection port's length","kind":"length","measurements":[{"id":"threaded","value":3.125,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.port_length}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder (this file's header)."}]},"port_front_x":{"label":"The ejection port's front end ahead of the takedown pin","kind":"length","measurements":[{"id":"threaded","value":6.036,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.port_front_x}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder (this file's header)."}]},"port_bottom_y":{"label":"The port's lower edge above the pin line, seen from the side (its ends R .25: 0.50 high)","kind":"length","measurements":[{"id":"threaded","value":0.841,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.port_bottom_y}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder (this file's header)."}]},"port_end_r":{"label":"The port's ends' radius (half its height from the side)","kind":"length","measurements":[{"id":"threaded","value":0.25,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.port_end_r}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder (this file's header)."}]},"fa_axis_angle":{"label":"The forward assist's axis, turned inward toward the front in plan","kind":"angle","measurements":[{"id":"threaded","value":20,"unit":"deg","pm":1,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.fa_axis_angle}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder (this file's header)."}]},"fa_bore_d":{"label":"The forward assist's bore","kind":"length","measurements":[{"id":"threaded","value":0.509,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.fa_bore_d}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder (this file's header)."}]},"fa_bore_depth":{"label":"The forward assist's bore, how deep its .509 runs from the housing's rear face","kind":"length","measurements":[{"id":"threaded","value":0.65,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.fa_bore_depth}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder (this file's header)."}]},"fa_inner_bore_d":{"label":"The forward assist's inner bore, ahead of the .509","kind":"length","measurements":[{"id":"threaded","value":0.315,"unit":"in","pm":0.001,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.fa_inner_bore_d}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder (this file's header)."}]},"fa_rear_x":{"label":"The forward assist bore's rear opening, X","kind":"length","measurements":[{"id":"threaded","value":-0.395,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.fa_rear_x}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder (this file's header)."}]},"fa_rear_z":{"label":"The forward assist bore's rear opening, out from the middle (Z)","kind":"length","measurements":[{"id":"threaded","value":1.09,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.fa_rear_z}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder (this file's header)."}]},"fa_housing_r":{"label":"The forward assist housing's radius about its axis (the forging's)","kind":"length","measurements":[{"id":"threaded","value":0.3125,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.fa_housing_r}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder (this file's header)."}]},"fa_housing_front_x":{"label":"The forward assist housing's front end, X","kind":"length","measurements":[{"id":"threaded","value":1.9,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.fa_housing_front_x}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder (this file's header)."}]},"fa_housing_out_rear":{"label":"The forward assist housing's outer face at the receiver's rear, out from the middle (Z)","kind":"length","measurements":[{"id":"threaded","value":1.67,"unit":"in","pm":0.1,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.fa_housing_out_rear}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder (this file's header)."}]},"fa_housing_outer_top_y":{"label":"The forward assist housing's outer face, its upper edge (where the face that slopes down from the body meets it), Y","kind":"length","measurements":[{"id":"threaded","value":1.2,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.fa_housing_outer_top_y}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder (this file's header)."}]},"fa_housing_outer_bottom_y":{"label":"The forward assist housing's outer face, its lower edge (where the face that slopes back in to the body begins), Y","kind":"length","measurements":[{"id":"threaded","value":0.92,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.fa_housing_outer_bottom_y}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder (this file's header)."}]},"deflector_out":{"label":"The brass deflector's reach out from the middle (Z)","kind":"length","measurements":[{"id":"threaded","value":1.47,"unit":"in","pm":0.1,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.deflector_out}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder (this file's header)."}]},"deflector_point_x":{"label":"The brass deflector's point (where it reaches furthest out), X","kind":"length","measurements":[{"id":"threaded","value":2.72,"unit":"in","pm":0.15,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.deflector_point_x}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder (this file's header)."}]},"deflector_point_y":{"label":"The brass deflector's point (where it reaches furthest out), Y","kind":"length","measurements":[{"id":"threaded","value":1.16,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.deflector_point_y}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder (this file's header)."}]},"cam_boss_x":{"label":"The cam pin's boss on the left side, its middle, X","kind":"length","measurements":[{"id":"threaded","value":5.14,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.cam_boss_x}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder. This receiver's own left view (604a860f4080, framed as the comment above this block says): its middle at 340.4 px (its outer face 322.0 to 359.3, its upper edge 312.7 to 368.0, its ends 301.3 to 379.2: all three centred within 0.3 px): 5.11, 0.03 behind the Threaded receiver's, as everything on this wall reads in this photo (the header); from the middle length's rear end it is 1.10 in for that receiver's 1.09."}]},"cam_boss_face_half_width":{"label":"The cam pin's boss, its upright outer face, half its length","kind":"length","measurements":[{"id":"threaded","value":0.172,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.cam_boss_face_half_width}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder. This receiver's own left view (604a860f4080, framed as the comment above this block says): rows 271 to 290: the face's even tone (57 to 60) between an edge line at 322.0 px and the lit end's half level at 359.3: 0.182, a hundredth more."}]},"cam_boss_face_top_y":{"label":"The cam pin's boss, its outer face's upper edge (and its ends' lower edge), Y","kind":"length","measurements":[{"id":"threaded","value":1.519,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.cam_boss_face_top_y}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder. This receiver's own left view (604a860f4080, framed as the comment above this block says): columns 325 to 356: the lit face above (108 to 123) gives way to the outer face (58 to 61) at 267.1 px: 1.513."}]},"cam_boss_bottom_y":{"label":"The cam pin's boss, its outer face's lower edge, where it runs out on the body's sloped face, Y","kind":"length","measurements":[{"id":"threaded","value":1.21,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.cam_boss_bottom_y}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder. This receiver's own left view (604a860f4080, framed as the comment above this block says): columns 325 to 356: the outer face (57 to 61) gives way to the lit sloped face (100) at 299.5 px: 1.198."}]},"cam_boss_top_y":{"label":"The cam pin's boss, its upper edge on the band under the rail, Y","kind":"length","measurements":[{"id":"threaded","value":1.648,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.cam_boss_top_y}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder. This receiver's own left view (604a860f4080, framed as the comment above this block says): columns 325 to 356: the band (50 to 53) gives way to a lit line (100) at 254.2 px: 1.638."}]},"cam_boss_top_half_width":{"label":"The cam pin's boss, its upper edge, half its length","kind":"length","measurements":[{"id":"threaded","value":0.245,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.cam_boss_top_half_width}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder. This receiver's own left view (604a860f4080, framed as the comment above this block says): row 256: lit from 312.7 to 368.0 px: 0.269, the furthest of these readings from that receiver's (0.024 more; the row is 2 px under the edge, where the ends have begun to spread)."}]},"cam_boss_ear_half_width":{"label":"The cam pin's boss, its two ends at their lower edge, half the length between them","kind":"length","measurements":[{"id":"threaded","value":0.373,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.cam_boss_ear_half_width}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder. This receiver's own left view (604a860f4080, framed as the comment above this block says): rows 265 to 274: the lit ends reach 301.3 px ahead and 379.2 behind: 0.379."}]},"cam_boss_flank_run":{"label":"The cam pin's boss, how far along the body each flank of its outer face runs before it reaches the band","kind":"length","measurements":[{"id":"threaded","value":0.135,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.cam_boss_flank_run}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder. This receiver's own left view (604a860f4080, framed as the comment above this block says): row 274, at the sloped face's upper edge: the dark flank ahead of the outer face is 14 px wide: 0.136."}]},"left_pad_rear_x":{"label":"The flat pad low on the left wall, its rear end, X","kind":"length","measurements":[{"id":"threaded","value":3.077,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.left_pad_rear_x}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder. This receiver's own left view (604a860f4080, framed as the comment above this block says): rows 362, 372 and 384: a lit end face begins at 553.5 px at all three and widens downward: 3.04, 0.04 behind that receiver's (the header); from the middle length's rear end it is 0.97 in for that receiver's 0.973."}]},"left_pad_front_x":{"label":"The flat pad low on the left wall, its front end, X","kind":"length","measurements":[{"id":"threaded","value":6.202,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.left_pad_front_x}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder. This receiver's own left view (604a860f4080, framed as the comment above this block says): rows 362 to 384: a dark wedge ahead of the pad ends at 232.8 px in all three (its front edge runs from 229 px at row 362 to 222 at row 384, where that receiver's photo has a band of in-between tone 0.07 in long): 6.16, 0.04 behind that receiver's (the header); from the middle length's rear end it is 2.15 in for that receiver's 2.152."}]},"left_pad_top_y":{"label":"The flat pad low on the left wall, the upper edge of its front and rear lengths, Y","kind":"length","measurements":[{"id":"threaded","value":0.662,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.left_pad_top_y}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder. This receiver's own left view (604a860f4080, framed as the comment above this block says): columns 260, 300, 340, 370, 480, 500 and 520: a crease (the wall's 58 to 60 falls to 52 to 55 between 355 and 357 px) that the plain wall behind the pad doesn't have (columns 600 and 700): 0.64 to 0.65."}]},"left_pad_step_rear_x":{"label":"The flat pad low on the left wall, its middle length's rear end, X","kind":"length","measurements":[{"id":"threaded","value":4.05,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.left_pad_step_rear_x}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder. This receiver's own left view (604a860f4080, framed as the comment above this block says): rows 362, 372 and 384: a lit end face 453.3 to 457.5 px with a dark line ahead of it, and at row 348 (above the other lengths) the middle length's tone ends at 454.3: 4.00 to 4.01, 0.04 behind that receiver's (the header), the furthest of the places along it."}]},"left_pad_step_front_x":{"label":"The flat pad low on the left wall, its middle length's front end, X","kind":"length","measurements":[{"id":"threaded","value":4.585,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.left_pad_step_front_x}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder. This receiver's own left view (604a860f4080, framed as the comment above this block says): rows 362 to 384: two lit lines at 396 and 400 px, and at rows 348 and 352 (above the other lengths) the middle length's tone begins at 401.7: 4.51 to 4.58; the end is a zone 0.07 in long in this photo, and which line in it is the face's edge isn't told."}]},"left_pad_step_top_y":{"label":"The flat pad low on the left wall, its middle length's upper edge, Y","kind":"length","measurements":[{"id":"threaded","value":0.743,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.left_pad_step_top_y}","via":"harvest"},"note":"The M4E1 Threaded receiver's, by reference: the same receiver behind the shoulder. This receiver's own left view (604a860f4080, framed as the comment above this block says): columns 410, 425 and 440: the wall's 58 steps to the middle length's 53 at 347.1 px: 0.734."}]}}},{"subject":"aero-m4e1-lower","title":"Aero Precision M4E1 complete lower, A2 grip and M4 stock","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"spec","value":33.25,"unit":"oz","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision","url":"https://www.aeroprecisionusa.com/m4e1-complete-lower-a2-grip-m4-stock-black","retrieved":"2026-10-02","via":"harvest"},"note":"Aero's spec table, \"Weight(s) 33.25 oz\", for the complete lower as sold (A2 grip, M4 stock, lower parts kit, carbine receiver extension, buffer and spring)."},{"id":"brownells","value":33.25,"unit":"oz","source":{"type":"spec","publisher":"retailer","name":"Brownells","url":"https://www.brownells.com/gun-parts/rifle-parts/rifle-receivers-parts/m4e1-complete-lower-receiver-w-a2-grip--m4-stock-for-ar-15/","retrieved":"2026-10-02","via":"harvest"},"note":"Brownells' \"Weight(s): 33.25 oz\": Aero's figure restated, not a weighing (its \"Item Weight (lbs): 2.078\" is a shipping figure)."}],"adopt":{"from":"spec","reason":"The maker's figure; the retailers restate it."},"note":"Onboarding checklist: Manufacturer spec table (stripped, or complete as sold); a retailer's figure may be boxed."},"width":{"label":"Receiver maximum width (Z)","kind":"length","measurements":[{"id":"front","value":1.558,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-m4e1-lower 3fb9b60111c0 (front view, Aero's studio photo of the stripped M4E1 (the pivot lug above the magwell))","scaleRef":"scale from aero-m4e1-lower.height = 4.079 in (y-extent 542 px → 132.9 px/in)","method":"width of the traced outline (tools/trace.py)","via":"harvest"},"note":"The widest point, seen from the front: the side panels at their top, near the deck (the bolt catch's bosses on the left, the fence's panel on the right), not the magwell's mouth (about 1.42 across in this view). Seen from ahead, so read large: the rear view has those panels 1.18 to 1.27 across, and from below (profiles.bottom's photo, ahead of its box) 1.32 to 1.36. (Corrected 2026-10-03: it was taken for the mouth's flare.)"},{"id":"faces","value":1.374,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.panel_right_out} + {.bolt_catch_boss_out}","via":"harvest"},"note":"2026-10-03: the right panel's face and the left bosses' face, both at the deck, each read on two specimens' bottom views at the TDP body's scale."},{"id":"front-own-scale","value":1.418,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/aero-m4e1-lower 3fb9b60111c0 (front view, Aero's studio photo of the stripped M4E1)","scaleRef":"the front lug's slot (std.ar15.front_lug_slot_width, .500 REF): 73 px, 146 px/in","method":"the traced outline's widest, 207 px (1.558 at the height's 132.9 px/in)","via":"harvest"}}],"adopt":{"from":"faces","reason":"The faces read in their own planes on two specimens; the front view at its own standard reads 0.044 wider (its widest row takes in edges seen past the faces), and at the height's scale 10% wider still."},"note":"Onboarding checklist: The TDP's body width for a mil-spec forging (std.ar15.lower_body_width); a maker's figure or an end view for anything else. No maker's figure and no end view on file (discovery 2026-10-02). The receiver's body at the pins is a mil-spec upper's mate, so the model uses the TDP's body width there and says so; the M4E1's flared magwell and integral guard are wider and unsourced."},"buffer_axis_above_pin":{"label":"Receiver extension (bore) axis above the takedown pin centre","kind":"length","measurements":[{"id":"std","value":0.8775,"unit":"in","pm":0.0015,"source":{"type":"derived","expr":"{std.ar15.bore_axis_y}","via":"user"},"note":"A lower that takes a standard receiver extension has its thread on the Army drawing's axis (M6). Aero: the M4E1 is \"compatible with all mil-spec AR15 parts\" (its page, read 2026-10-02), so the standard's hole is its hole."}],"adopt":{"from":"std","reason":"The published standard; no photo has been read against it yet."},"note":"Onboarding checklist: The Army's drawings for a mil-spec lower (std.ar15.bore_axis_y); check it on a pin-framed side photo, allowing for the pins' near ends being nearer the lens."},"magazine_seat_x":{"label":"Magazine seat, X (a seated magazine's frame origin ahead of the takedown pin)","kind":"length","measurements":[{"id":"milspec","value":3.4915,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{bad-workhorse-lower.magazine_seat_x}","via":"user"},"note":"Where a Black Dog magazine seats in a mil-spec magwell: since 2026-10-03 from the Army drawing's well and catch slot and the user's own magazine (its length, its catch notch), recorded on the Workhorse; the photos of magazines seated in two other rifles are beside it there. The M4E1's magwell is mil-spec inside (Aero: compatible with all mil-spec parts; its \"Increased Magwell Flare\" is the mouth); a photo of a magazine seated in an M4E1 would make this its own."}],"adopt":{"from":"milspec","reason":"The seat belongs to the standard magwell and the magazine's catch notch, not to the receiver's outside; no photo of a magazine seated in an M4E1 is on file."},"note":"Onboarding checklist: A pin-framed photo of a magazine seated in it, fitted with its traced outline (trace.py `register`)."},"magazine_seat_y":{"label":"Magazine seat, Y (the feed-lip top of a seated magazine)","kind":"length","measurements":[{"id":"milspec","value":1.003,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{bad-workhorse-lower.magazine_seat_y}","via":"user"},"note":"Where a Black Dog magazine seats in a mil-spec magwell: since 2026-10-03 from the Army drawing's well and catch slot and the user's own magazine (its length, its catch notch), recorded on the Workhorse; the photos of magazines seated in two other rifles are beside it there. The M4E1's magwell is mil-spec inside (Aero: compatible with all mil-spec parts; its \"Increased Magwell Flare\" is the mouth); a photo of a magazine seated in an M4E1 would make this its own."}],"adopt":{"from":"milspec","reason":"The seat belongs to the standard magwell and the magazine's catch notch, not to the receiver's outside; no photo of a magazine seated in an M4E1 is on file."},"note":"Onboarding checklist: The same photo. The TDP's magwell (2.553 x 0.898 in inside) bounds any magazine drawn in it."},"grip_seat_y":{"label":"Grip seat, Y (the underside a grip's flat top bears on, at the takedown pin's X)","kind":"length","measurements":[{"id":"right","value":-1.443,"unit":"in","pm":0.013,"source":{"type":"photo","photo":"references/aero-m4e1-lower 30b8c6d3edf1 (right side, Aero's studio photo of the stripped M4E1 (both pin holes open))","scaleRef":"rifle frame from reviewed holes takedown (179.5,230.5) r=14px, pivot (937.5,228.5) r=8px = takedown(0.0, 0.0), pivot(6.375, 0.0) (118.9 px/in)","method":"silhouette y_min in x [-0.2, 0.08] in frame coordinates; ± from hole-center and edge error","via":"harvest"},"note":"The receiver's underside just behind the step (the tang), where the grip's flat top bears."},{"id":"left","value":-1.444,"unit":"in","pm":0.013,"source":{"type":"photo","photo":"references/aero-m4e1-lower ae10e5019d19 (left side, Aero's studio photo of the stripped M4E1 (both pin holes open))","scaleRef":"rifle frame from reviewed holes takedown (819.5,267.5) r=15px, pivot (75.5,267.5) r=15px = takedown(0.0, 0.0), pivot(6.375, 0.0) (116.7 px/in)","method":"silhouette y_min in x [-0.2, 0.08] in frame coordinates; ± from hole-center and edge error","via":"harvest"},"note":"The receiver's underside just behind the step (the tang), where the grip's flat top bears."}],"adopt":{"from":"right","reason":"Onboarding: first proposal adopted; the others come from the same method and agree or are flagged."},"note":"Onboarding checklist: A pin-framed side photo: the receiver's underside behind the step. Each grip says where its own origin sits from here (D28)."},"trigger_guard_front_x":{"label":"Trigger guard front ear hole, X","kind":"length","measurements":[{"id":"tdp","value":3.3425,"unit":"in","pm":0.007,"source":{"type":"derived","expr":"{std.ar15.trigger_guard_front_x}","via":"user"},"note":"Where a mil-spec guard's front ear hole is. The M4E1's trigger guard is integral (Aero: \"Integrated Trigger Guard\"), so it has no ear holes; the slot is occupied and nothing is placed by this."}],"note":"Onboarding checklist: The TDP for a mil-spec lower (std.ar15.*). A lower with an integral trigger guard states where its guard's ears would be, so the fcg and grip anchors still frame it; its guard is drawn with the receiver."},"trigger_guard_front_y":{"label":"Trigger guard front ear hole, Y","kind":"length","measurements":[],"note":"Onboarding checklist: As above. The M4E1's guard is integral (no ear holes), and the standard doesn't give this one: left missing; nothing is placed by it while the guard slot is occupied."},"trigger_guard_rear_x":{"label":"Trigger guard rear ear hole, X","kind":"length","measurements":[{"id":"tdp","value":1.4985,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{std.ar15.trigger_guard_rear_x}","via":"user"},"note":"As trigger_guard_front_x: the standard's position; the M4E1's guard is integral."}],"note":"Onboarding checklist: As above."},"trigger_guard_rear_y":{"label":"Trigger guard rear ear hole, Y","kind":"length","measurements":[{"id":"tdp","value":-2.18,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{std.ar15.trigger_guard_rear_y}","via":"user"},"note":"As trigger_guard_front_x: the standard's position; the M4E1's guard is integral."}],"note":"Onboarding checklist: As above."},"trigger_pin_x":{"label":"Trigger pin hole centre, X","kind":"length","measurements":[{"id":"tdp","value":1.928,"unit":"in","pm":0.004,"source":{"type":"derived","expr":"{std.ar15.trigger_pin_x}","via":"user"},"note":"Aero: the M4E1 is \"compatible with all mil-spec AR15 parts\" (its page, read 2026-10-02), so the standard's hole is its hole."}],"note":"Onboarding checklist: The TDP (std.ar15.trigger_pin_x); every lower that takes a standard FCG has it there."},"trigger_pin_y":{"label":"Trigger pin hole centre, Y","kind":"length","measurements":[{"id":"right","value":-0.677,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aero-m4e1-lower 30b8c6d3edf1 (Aero's studio photo of the stripped M4E1, right side, 1000 x 630)","scaleRef":"pin frame (takedown→pivot pin holes = 6.375 in, 118.8 px/in)","method":"Hough circle on the open trigger pin hole, (403.8, 311.4) px, r 8.6 px (0.145 in: the .154 hole); the takedown hole's centre at (179.4, 231.0). Its x reads 1.889, 0.04 behind the standard's 1.928, as the Workhorse's photos did (the pins' near ends nearer the lens).","via":"harvest"},"note":"The Workhorse's photos read -0.678 and -0.689 for the same standard hole."}],"note":"Onboarding checklist: The TDP; checked on a pin-framed photo."},"trigger_face_x":{"label":"The trigger's face ahead of the takedown pin (a complete lower: its trigger, at rest)","kind":"length","measurements":[{"id":"complete","value":2.06,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/aero-m4e1-lower 4a14a1778a59 (Aero's studio photo of the complete lower, right side, 1000 x 630)","scaleRef":"pin frame (takedown→pivot pin heads = 6.375 in, 60.1 px/in)","method":"The trigger's blade on the integral guard's window feature polygon (profiles.complete.features.guard_window, tools/trace.py): its front edge runs from (2.18, -1.21) down through (2.02, -1.43), (1.97, -1.63), (2.02, -1.91) to the tip at (2.13, -2.10). The face where a finger lands, mid-blade: 2.06, and the ± covers the edge's lean.","via":"harvest"},"note":"A mil-spec trigger at rest (Aero's lower parts kit). The LaRue MBT-2S on the Workhorse sits 2.06 ahead of the pin too (its pin 1.928 + 0.129)."},{"id":"complete_edge","value":1.964,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aero-m4e1-lower 4a14a1778a59 (Aero's studio photo of the complete lower, right side, 1000 x 630)","scaleRef":"pin frame (takedown→pivot pin heads = 6.375 in, 60.2 px/in, the frame turned 0.30° to them)","method":"The blade's front edge where it stands black against the guard's white window, at half level, row by row from y -1.25 to -2.10 (every 0.05): 2.131 at the top, its deepest 1.964 at y -1.65 to -1.70, 2.125 at -2.10. The deepest point is the face. ± is a pixel (0.017) on a black-on-white edge read to a fraction of one, and the frame's scale.","via":"harvest"},"note":"Read again on 2026-10-03, when the Army drawing's trigger (profiles.trigger) turned to this photo had its face's deepest point at 1.978, y -1.73: 0.08 behind the first reading."}],"adopt":{"from":"complete_edge","reason":"Length of pull runs to the face where the finger lies, the deepest point of the blade's curve. The first reading (2.06 ± 0.06) is the middle of the edge's span from its top to its tip, which is no point on it; the drawing's outline at the fitted rest angle agrees with the edge (1.978)."},"note":"Onboarding checklist: A pin-framed side photo of the complete lower: the front of the trigger's shoe where a finger lands. Length of pull is read from here."},"trigger_rest_angle":{"label":"The trigger at rest: how far it is turned about its pin from the Army drawing's side elevation (positive turns the blade forward)","kind":"angle","measurements":[{"id":"complete","value":-1,"unit":"deg","pm":0.8,"source":{"type":"photo","photo":"references/aero-m4e1-lower 4a14a1778a59 (Aero's studio photo of the complete lower, right side, 1000 x 630)","scaleRef":"pin frame (takedown→pivot pin heads = 6.375 in, 60.2 px/in)","method":"The traced outline (profiles.trigger, from drawing 8448592) turned about the trigger pin to the blade's front edge and tip read on the photo (trigger_face_x's five points): best at -1.0 deg, rms 0.007 in; one pixel (0.017 in) at the blade, 1.4 in from the pin, is 0.7 deg.","via":"harvest"}}],"note":"The drawing's elevation has the trigger's tail level; at rest in the lower the trigger sits against the disconnector and hammer, which no drawing on file shows."},"butt_behind_pin":{"label":"The stock's butt behind the takedown pin, at the position it is drawn at (a complete lower)","kind":"length","measurements":[{"id":"complete_right","value":8.601,"unit":"in","pm":0.054,"source":{"type":"photo","photo":"references/aero-m4e1-lower 4a14a1778a59 (right side, Aero's studio photo of the complete lower APAR600101 (pin heads in place; the stock partly extended))","scaleRef":"rifle frame from reviewed holes takedown (560.5,218.5) r=14px, pivot (944.5,216.5) r=10px = takedown(0.0, 0.0), pivot(6.375, 0.0) (60.2 px/in)","method":"silhouette x_min in frame coordinates (negated); ± from hole-center and edge error","via":"harvest"},"note":"The stock's butt (its rearmost point), at the position Aero's photo shows: partly extended."},{"id":"complete_left","value":8.611,"unit":"in","pm":0.054,"source":{"type":"photo","photo":"references/aero-m4e1-lower 9738868e44f9 (left side, Aero's studio photo of the complete lower APAR600101)","scaleRef":"rifle frame from reviewed holes takedown (438.5,222.5) r=7px, pivot (55.5,221.5) r=5px = takedown(0.0, 0.0), pivot(6.375, 0.0) (60.1 px/in)","method":"silhouette x_min in frame coordinates (negated); ± from hole-center and edge error","via":"harvest"},"note":"The stock's butt (its rearmost point), at the position Aero's photo shows: partly extended."}],"adopt":{"from":"complete_right","reason":"Onboarding: first proposal adopted; the others come from the same method and agree or are flagged."},"note":"Onboarding checklist: A pin-framed side photo of the complete lower with its stock collapsed (say which position); the stock maker's lengths of pull are a check only (M6)."},"height":{"label":"Overall height: the tower ring's top to the lowest point (the end views are scaled by it)","kind":"length","measurements":[{"id":"right","value":4.079,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-m4e1-lower 30b8c6d3edf1 (right side, Aero's studio photo of the stripped M4E1, pin-framed by its open holes)","scaleRef":"frame from the reviewed holes takedown (179.5,230.5) r=14px, pivot (937.5,228.5) r=8px (118.9 px/in, rms 0.000 in over 2 points)","method":"height of the traced outline (tools/trace.py)","via":"harvest"},"note":"The tower ring's top to the lowest point: what the end views are scaled by."}],"note":"From the pin-framed photos (tools/onboard.py measure, tools/trace.py)."},"tower_od":{"label":"The buffer tower's ring, across (the end view; the standard's is 1.392)","kind":"length","measurements":[{"id":"rear","value":1.351,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-m4e1-lower 748bb1292dc5 (rear view, Aero's studio photo of the stripped M4E1 (the tower ring above, the magwell below))","scaleRef":"scale from aero-m4e1-lower.height = 4.079 in (y-extent 544 px → 133.4 px/in)","method":"median row width in y [-0.9, -0.5] (1.290–1.365) of the traced outline (tools/trace.py)","via":"harvest"},"note":"The buffer tower's ring, across; the standard's is 1.392."},{"id":"rear_fde","value":1.275,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-m4e1-lower cff1e09f0457 (rear view, Aero's studio photo of the stripped M4E1 in FDE Cerakote (APAR600002C))","scaleRef":"scale from aero-m4e1-lower.height = 4.079 in (y-extent 544 px → 133.4 px/in)","method":"median row width in y [-0.9, -0.5] (1.200–1.290) of the traced outline (tools/trace.py)","via":"harvest"},"note":"The ring across, on the FDE specimen's photo in the black one's pose: the same 544 px tall, the ring 10 px narrower."}],"adopt":{"from":"rear","reason":"The black photo, the rear profile's. The bottom view (profiles.bottom) is scaled by this: at 1.351 its length from the rear face to where the sides rise into the magazine well's panels is 3.997 (the right photo's fence slope from rear_face_x: 4.014; from the TDP's rear face: 3.999) and its body 0.894 (the TDP's 0.88); at 1.275 they would be 3.77 and 0.84. The two rear photos, both scaled by the side's height, are 6% apart: how far a height-scaled end view's widths hold. The ring has flats (the rear view's sides run straight over 0.19 in; from below its top is a flat 0.58 wide), so the TDP's round 1.392 isn't its width across."},"note":"From the pin-framed photos (tools/onboard.py measure, tools/trace.py)."},"rear_behind_pin":{"label":"Rear of the buffer-tower ring behind the takedown pin","kind":"length","measurements":[{"id":"right","value":1.155,"unit":"in","pm":0.013,"source":{"type":"photo","photo":"references/aero-m4e1-lower 30b8c6d3edf1 (right side, Aero's studio photo of the stripped M4E1 (both pin holes open))","scaleRef":"rifle frame from reviewed holes takedown (179.5,230.5) r=14px, pivot (937.5,228.5) r=8px = takedown(0.0, 0.0), pivot(6.375, 0.0) (118.9 px/in)","method":"silhouette x_min in frame coordinates (negated); ± from hole-center and edge error","via":"harvest"},"note":"Rearmost point: the buffer-tower ring."},{"id":"left","value":1.135,"unit":"in","pm":0.013,"source":{"type":"photo","photo":"references/aero-m4e1-lower ae10e5019d19 (left side, Aero's studio photo of the stripped M4E1 (both pin holes open))","scaleRef":"rifle frame from reviewed holes takedown (819.5,267.5) r=15px, pivot (75.5,267.5) r=15px = takedown(0.0, 0.0), pivot(6.375, 0.0) (116.7 px/in)","method":"silhouette x_min in frame coordinates (negated); ± from hole-center and edge error","via":"harvest"},"note":"Rearmost point: the buffer-tower ring."}],"adopt":{"from":"right","reason":"Onboarding: first proposal adopted; the others come from the same method and agree or are flagged."},"note":"From the pin-framed photos (tools/onboard.py measure, tools/trace.py)."},"front_ahead_of_pin":{"label":"Front of the pivot-pin lug ahead of the takedown pin","kind":"length","measurements":[{"id":"right","value":6.547,"unit":"in","pm":0.022,"source":{"type":"photo","photo":"references/aero-m4e1-lower 30b8c6d3edf1 (right side, Aero's studio photo of the stripped M4E1 (both pin holes open))","scaleRef":"rifle frame from reviewed holes takedown (179.5,230.5) r=14px, pivot (937.5,228.5) r=8px = takedown(0.0, 0.0), pivot(6.375, 0.0) (118.9 px/in)","method":"silhouette x_max in frame coordinates; ± from hole-center and edge error","via":"harvest"},"note":"Front of the pivot-pin lug."},{"id":"left","value":6.645,"unit":"in","pm":0.023,"source":{"type":"photo","photo":"references/aero-m4e1-lower ae10e5019d19 (left side, Aero's studio photo of the stripped M4E1 (both pin holes open))","scaleRef":"rifle frame from reviewed holes takedown (819.5,267.5) r=15px, pivot (75.5,267.5) r=15px = takedown(0.0, 0.0), pivot(6.375, 0.0) (116.7 px/in)","method":"silhouette x_max in frame coordinates; ± from hole-center and edge error","via":"harvest"},"note":"Front of the pivot-pin lug."}],"adopt":{"from":"right","reason":"The right photo; the left reads the lug 0.10 further forward (perspective at the front end, as the Workhorse's photos did), and the complete lower's right photo agrees with the right (6.574)."},"note":"From the pin-framed photos (tools/onboard.py measure, tools/trace.py)."},"tower_top_above_pin":{"label":"Top of the buffer-tower ring above the pin line","kind":"length","measurements":[{"id":"right","value":1.554,"unit":"in","pm":0.013,"source":{"type":"photo","photo":"references/aero-m4e1-lower 30b8c6d3edf1 (right side, Aero's studio photo of the stripped M4E1 (both pin holes open))","scaleRef":"rifle frame from reviewed holes takedown (179.5,230.5) r=14px, pivot (937.5,228.5) r=8px = takedown(0.0, 0.0), pivot(6.375, 0.0) (118.9 px/in)","method":"silhouette y_max in frame coordinates; ± from hole-center and edge error","via":"harvest"},"note":"Top of the buffer-tower ring."},{"id":"left","value":1.572,"unit":"in","pm":0.014,"source":{"type":"photo","photo":"references/aero-m4e1-lower ae10e5019d19 (left side, Aero's studio photo of the stripped M4E1 (both pin holes open))","scaleRef":"rifle frame from reviewed holes takedown (819.5,267.5) r=15px, pivot (75.5,267.5) r=15px = takedown(0.0, 0.0), pivot(6.375, 0.0) (116.7 px/in)","method":"silhouette y_max in frame coordinates; ± from hole-center and edge error","via":"harvest"},"note":"Top of the buffer-tower ring."}],"adopt":{"from":"right","reason":"Onboarding: first proposal adopted; the others come from the same method and agree or are flagged."},"note":"From the pin-framed photos (tools/onboard.py measure, tools/trace.py)."},"deck_above_pin":{"label":"Receiver top deck above the pin line","kind":"length","measurements":[{"id":"right","value":0.247,"unit":"in","pm":0.013,"source":{"type":"photo","photo":"references/aero-m4e1-lower 30b8c6d3edf1 (right side, Aero's studio photo of the stripped M4E1 (both pin holes open))","scaleRef":"rifle frame from reviewed holes takedown (179.5,230.5) r=14px, pivot (937.5,228.5) r=8px = takedown(0.0, 0.0), pivot(6.375, 0.0) (118.9 px/in)","method":"silhouette y_max in x [0.6, 5.8] in frame coordinates; ± from hole-center and edge error","via":"harvest"},"note":"Receiver top edge between the tower and the pivot lug (where the upper sits)."},{"id":"left","value":0.253,"unit":"in","pm":0.013,"source":{"type":"photo","photo":"references/aero-m4e1-lower ae10e5019d19 (left side, Aero's studio photo of the stripped M4E1 (both pin holes open))","scaleRef":"rifle frame from reviewed holes takedown (819.5,267.5) r=15px, pivot (75.5,267.5) r=15px = takedown(0.0, 0.0), pivot(6.375, 0.0) (116.7 px/in)","method":"silhouette y_max in x [0.6, 5.8] in frame coordinates; ± from hole-center and edge error","via":"harvest"},"note":"Receiver top edge between the tower and the pivot lug (where the upper sits)."}],"adopt":{"from":"right","reason":"Onboarding: first proposal adopted; the others come from the same method and agree or are flagged."},"note":"From the pin-framed photos (tools/onboard.py measure, tools/trace.py)."},"bottom_below_pin":{"label":"Lowest point below the pin line (the integral guard or the magwell front)","kind":"length","measurements":[{"id":"right","value":2.508,"unit":"in","pm":0.014,"source":{"type":"photo","photo":"references/aero-m4e1-lower 30b8c6d3edf1 (right side, Aero's studio photo of the stripped M4E1 (both pin holes open))","scaleRef":"rifle frame from reviewed holes takedown (179.5,230.5) r=14px, pivot (937.5,228.5) r=8px = takedown(0.0, 0.0), pivot(6.375, 0.0) (118.9 px/in)","method":"silhouette y_min in frame coordinates (negated); ± from hole-center and edge error","via":"harvest"},"note":"Lowest point: the integral trigger guard's bow or the magwell's front."},{"id":"left","value":2.523,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aero-m4e1-lower ae10e5019d19 (left side, Aero's studio photo of the stripped M4E1 (both pin holes open))","scaleRef":"rifle frame from reviewed holes takedown (819.5,267.5) r=15px, pivot (75.5,267.5) r=15px = takedown(0.0, 0.0), pivot(6.375, 0.0) (116.7 px/in)","method":"silhouette y_min in frame coordinates (negated); ± from hole-center and edge error","via":"harvest"},"note":"Lowest point: the integral trigger guard's bow or the magwell's front."}],"adopt":{"from":"right","reason":"Onboarding: first proposal adopted; the others come from the same method and agree or are flagged."},"note":"From the pin-framed photos (tools/onboard.py measure, tools/trace.py)."},"magwell_front_x":{"label":"Magwell front face, X","kind":"length","measurements":[{"id":"right","value":6.156,"unit":"in","pm":0.021,"source":{"type":"photo","photo":"references/aero-m4e1-lower 30b8c6d3edf1 (right side, Aero's studio photo of the stripped M4E1 (both pin holes open))","scaleRef":"rifle frame from reviewed holes takedown (179.5,230.5) r=14px, pivot (937.5,228.5) r=8px = takedown(0.0, 0.0), pivot(6.375, 0.0) (118.9 px/in)","method":"silhouette x_max in x [3.0, 7.0] in y [-1.95, -1.3] in frame coordinates; ± from hole-center and edge error","via":"harvest"},"note":"Front face of the magwell."},{"id":"left","value":6.268,"unit":"in","pm":0.022,"source":{"type":"photo","photo":"references/aero-m4e1-lower ae10e5019d19 (left side, Aero's studio photo of the stripped M4E1 (both pin holes open))","scaleRef":"rifle frame from reviewed holes takedown (819.5,267.5) r=15px, pivot (75.5,267.5) r=15px = takedown(0.0, 0.0), pivot(6.375, 0.0) (116.7 px/in)","method":"silhouette x_max in x [3.0, 7.0] in y [-1.95, -1.3] in frame coordinates; ± from hole-center and edge error","via":"harvest"},"note":"Front face of the magwell."}],"adopt":{"from":"right","reason":"Onboarding: first proposal adopted; the others come from the same method and agree or are flagged."},"note":"From the pin-framed photos (tools/onboard.py measure, tools/trace.py)."},"rear_face_x":{"label":"Receiver rear face below the tower ring, X","kind":"length","measurements":[{"id":"right","value":-1.14,"unit":"in","pm":0.013,"source":{"type":"photo","photo":"references/aero-m4e1-lower 30b8c6d3edf1 (right side, Aero's studio photo of the stripped M4E1 (both pin holes open))","scaleRef":"rifle frame from reviewed holes takedown (179.5,230.5) r=14px, pivot (937.5,228.5) r=8px = takedown(0.0, 0.0), pivot(6.375, 0.0) (118.9 px/in)","method":"silhouette x_min in y [-1.0, 0.0] in frame coordinates; ± from hole-center and edge error","via":"harvest"},"note":"Rear face of the receiver below the buffer-tower ring."},{"id":"left","value":-1.118,"unit":"in","pm":0.013,"source":{"type":"photo","photo":"references/aero-m4e1-lower ae10e5019d19 (left side, Aero's studio photo of the stripped M4E1 (both pin holes open))","scaleRef":"rifle frame from reviewed holes takedown (819.5,267.5) r=15px, pivot (75.5,267.5) r=15px = takedown(0.0, 0.0), pivot(6.375, 0.0) (116.7 px/in)","method":"silhouette x_min in y [-1.0, 0.0] in frame coordinates; ± from hole-center and edge error","via":"harvest"},"note":"Rear face of the receiver below the buffer-tower ring."}],"adopt":{"from":"right","reason":"Onboarding: first proposal adopted; the others come from the same method and agree or are flagged."},"note":"From the pin-framed photos (tools/onboard.py measure, tools/trace.py)."},"grip_bottom_y":{"label":"The A2 grip's lowest point below the pin line (the complete lower)","kind":"length","measurements":[{"id":"complete","value":4.93,"unit":"in","pm":0.031,"source":{"type":"photo","photo":"references/aero-m4e1-lower 4a14a1778a59 (right side, Aero's studio photo of the complete lower APAR600101, pin-framed by its pin heads)","scaleRef":"frame from the reviewed holes takedown (560.5,218.5) r=14px, pivot (944.5,216.5) r=10px (60.2 px/in, rms 0.000 in over 2 points)","method":"−y_min in x [-2.3, 0.2] of the traced outline (tools/trace.py)","via":"harvest"},"note":"The A2 grip's lowest point, on the complete lower's silhouette (the grip hangs behind the takedown pin)."}],"note":"From the complete lower's traced silhouette (tools/trace.py); the measure stage's reading was the stock's latch, not the grip."},"grip_width":{"label":"The A2 grip's width over its knurl (Z)","kind":"length","measurements":[{"id":"tdp","value":1.27,"unit":"in","pm":0.02,"stated":"1.270 APPROX OVER KNURL","source":{"type":"standard","doc":"US Army TDP drawing 9349127 (Grip, Pistol), rev J, sheet 1 of 1 (filmed in two frames: frame 1 of 2, the M16 package's PDF page 33), the bottom view: the grip seen along its axis, below and behind the side view","via":"user"},"note":"The drawing's \"APPROX\" taken as ± 0.02. Read between the bottom view's two extension lines, which are tangent to its outline's sides (346.6 px apart on the 600 dpi scan between the lines' middles; the traced outline, at its strokes' middle, is 345 across). First cited (2026-10-02) as Section A-A: that is a partial section through the backstrap's serrations at the grip's lower rear, with no width on it. Aero's page says \"A2 Grip - Black\": the mil-spec pattern, which the drawing dimensions; the checkering's pitch (14) and the slot are there too."}],"note":"The A2 grip is the TDP's pistol grip (9349127). The width over the knurl is the widest the grip is; its top, where it bears on the receiver, is .885 (grip_body_width). The drawing says DO NOT SCALE: its interface dimensions are drawn 5 to 7% off (1.275 and 1.390 read 258 and 263 px/in), while its exterior views agree with Aero's photo within 2% (the side view registered on profiles.complete at 277 px/in, rms 0.013 in; the bottom view, scaled by this width, at 272 px/in, and by the photo's depth square to the axis at 272.5). The bottom view's .39 ± .01 (its centre line to the front end's theoretical corner) lands at 0.38 in the traced section. Its Section D-D says the exterior contour is \"per sample furnished by the contractor and approved by the Government technical activity\"."},"grip_body_width":{"label":"The A2 grip's top, across (Z): the block that bears on the receiver (the slot along it is .380 + .005 wide)","kind":"length","measurements":[{"id":"tdp","value":0.885,"unit":"in","pm":0.015,"stated":".885 ± .015","source":{"type":"standard","doc":"US Army TDP drawing 9349127 (Grip, Pistol), rev J, sheet 1, frame 1 of 2 (PDF page 33), the top view","via":"user"},"note":"Between the top view's extension lines from the block's two long edges (datum -A- is its centre plane; the slot in it is .380 + .005 wide). The front view shows the block this wide for about the top quarter of the grip's height before the body widens to the knurl. As drawn it reads 0.85 (top view) and 0.84 (front view) at the scale the exterior views share: drawn 4 to 5% narrow. This entry first held Section C-C's \".820 ± .01\" (2026-10-02), read as a width at the tang: Section C-C is the mid-plane section (its cut line is the front view's centre line), so nothing on it spans Z; the .820 runs along the grip's axis, between two lines square to it below the slot."}]},"grip_axis_angle":{"label":"The A2 grip's axis from its top face: the screw bore, along which the drawing's bottom view looks","kind":"angle","measurements":[{"id":"tdp","value":60,"unit":"deg","pm":1,"stated":"60° (basic) between datum -E- (the top face) and the bore, Section C-C; 30° ± 1° between the top face and the lines square to the axis, the side view","source":{"type":"standard","doc":"US Army TDP drawing 9349127 (Grip, Pistol), rev J, sheet 1: Section C-C (frame 2 of 2, PDF page 32) and the side view (frame 1, PDF page 33)","via":"user"},"note":"The ± is the side view's ± 1° on the 30°. As scanned, the side view's 30° lines lie 29.4° and 29.6° below its top face, and the bottom view's long axis (its 1.270's extension lines) 29.4°: the view is drawn square to this axis."}]},"grip_top_slope":{"label":"The A2 grip's top face against the bore line, in the rifle frame (+: rising toward the muzzle)","kind":"angle","measurements":[{"id":"registered","value":1.7,"unit":"deg","pm":0.6,"source":{"type":"photo","photo":"references/aero-m4e1-lower 4a14a1778a59 (right side, Aero's studio photo of the complete lower APAR600101, traced as profiles.complete) and be585e351439 (US Army TDP drawing 9349127, frame 1 of 2: its side view)","scaleRef":"the complete lower's pin frame (std.ar15.pin_spacing); the drawing's scale is fitted with the rotation","method":"The drawing's side view, filled and its lines opened away, registered by a similarity (ICP) on the traced outline below the receiver (its top 0.3 in left out, where the receiver hides the grip in the photo): 277.3 px/in, rotation +1.28° onto a top face that lies at +0.38° on the scan, rms 0.013 in over 2794 points. The ± is the spread of the rotation over parts of the outline (the rear half alone +0.9°, the front half +2.2°). Scratch: .cache/grip/register.py, register_var.py.","via":"user"},"note":"The grip's top face, where the drawing levels it, sits 1.7° nose-up on Aero's lower. Read off one photo of one lower; with grip_axis_angle it sets grip_rake."}]},"grip_rake":{"label":"The A2 grip's axis from the vertical in the rifle frame (its bottom further back): the side outline turns by this to stand the axis up","kind":"angle","measurements":[{"id":"derived","value":28.3,"unit":"deg","pm":1.2,"source":{"type":"derived","expr":"90 - {.grip_axis_angle} - {.grip_top_slope}","via":"user"},"note":"The bottom view (profiles.grip_section) is a plan in the frame this angle stands up. With the top face taken as level it would be 30°, and the photo's depth along the section (grip_depth) 2.095 against the bottom view's 2.159."}]},"grip_depth":{"label":"The A2 grip's depth square to its axis: its side outline's whole extent along the direction grip_rake below the bore line, toward the muzzle","kind":"length","measurements":[{"id":"complete","value":2.153,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/aero-m4e1-lower 4a14a1778a59 (right side, Aero's studio photo of the complete lower APAR600101, pin-framed by its pin heads)","scaleRef":"the pin frame of the complete lower's traced outline (profiles.complete, std.ar15.pin_spacing)","method":"profiles.complete below y -2.5 between x -2.5 and 1.0 (the grip below the receiver, behind the guard) projected on the direction 28.3° (grip_rake) below the bore line: from the bottom-rear corner (-2.181, -4.347) to the finger swell (0.846, -3.267). The ± covers the outline's 0.02 and grip_rake's ± 1.2° (0.036 in a degree here); the receiver hides nothing that reaches further along it (the drawing registered on the photo puts the top block's front at 2.08).","via":"harvest"},"note":"What the bottom view (profiles.grip_section) is scaled by along its length, so that its extent along x' is the side outline's and a visual hull of the two meets at both ends. The bottom view scaled by grip_width across gives 2.157 for its length: within 0.2%."}]},"grip_top_y":{"label":"The A2 grip's top face (where it bears on the receiver), its height at the takedown pin's X in the part frame; it rises grip_top_slope toward the muzzle","kind":"length","measurements":[{"id":"registered","value":-1.221,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/aero-m4e1-lower 4a14a1778a59 (right side, Aero's studio photo of the complete lower APAR600101, traced as profiles.complete) and be585e351439 (US Army TDP drawing 9349127, frame 1 of 2: its side view)","scaleRef":"the complete lower's pin frame (std.ar15.pin_spacing); the drawing's scale is fitted with the rotation","method":"The registration grip_top_slope is read from (the drawing's side view on the traced outline below the receiver, ICP, 277.3 px/in, rms 0.013 in) carries the side view's top line (fitted at (3425.0, 2413.1) px, +0.38° on the scan) into the part frame: y −1.221 at x 0, −1.230 at the grip's rear-top corner (x −0.34) and −1.190 at the top block's front (x 1.07). The ± is the spread over parts of the outline (−1.218 to −1.245; the rear half alone, fitted at 282 px/in, −1.282): the face is extrapolated from 0.3 in below it, where the receiver stops hiding the grip.","via":"user"},"note":"Where the grip's front view (profiles.grip_front) is hung: its top is this face. 0.22 above grip_seat_y (−1.443), which is the receiver's underside behind the step at the pin's X, not the face a grip bears on: the receiver's lug stands into the grip's slot below it."}]},"grip_height":{"label":"The A2 grip's height: its top face to its lowest point","kind":"length","measurements":[{"id":"derived","value":3.709,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{.grip_bottom_y} + {.grip_top_y}","via":"user"},"note":"Taken square to the bore line; square to the top face (1.7° off) the lowest point is 0.007 lower, inside the ±. The drawing's front view is drawn this tall at the scale its side view takes on Aero's photo (1026 px at 277 px/in: 3.70); scaled by its block's stated .885 it is 3.90 (profiles.grip_front's check)."}]},"stock_width":{"label":"The M4 stock's width (Z), its body","kind":"length","measurements":[{"id":"patent","value":1.443,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-m4e1-lower 3f4478bbd4cd (US D620,067 S, the Army's design patent for an M4-pattern buttstock, sheet 3, FIG. 3 top plan, 300 dpi)","scaleRef":"the receiver extension in the same figure, 191 px across, as the standard's mil-spec OD (std.receiver_extension.milspec_od, 1.148 in): 166.4 px/in","method":"the body's width in the plan view, 240 px (± 1) all along it from the stock's front to the butt's flare","via":"harvest"}},{"id":"leapers","value":1.4,"unit":"in","stated":"Width 1.4 in (35.4 mm)","source":{"type":"spec","publisher":"manufacturer","name":"Leapers, UTG PRO 6-Position Mil-spec Stock (RBU6BM), its dimensions table: a clone of the M4 pattern, not Aero's stock","url":"https://www.leapers.com/products-utgpro-rbu6bm.html","retrieved":"2026-10-02","via":"harvest"}},{"id":"hurley","value":1.4,"unit":"in","stated":"There are various manufacturers of this type of stock out there, but the outside width of the stock should be 1.4\" for best fit.","source":{"type":"spec","publisher":"retailer","name":"Hurley Welding, Cheek Riser for M4/A1 'Waffle' Stock: the width of the USGI-pattern stocks it fits","url":"https://www.hurleywelding.com/product-page/cheek-riser-for-m4-a1-waffle-stock-for-ar15","retrieved":"2026-10-02","via":"harvest"}}],"adopt":{"from":"patent","reason":"Measured in an orthographic drawing against a standard in the same figure; the two stated figures, to a tenth, agree with it."},"note":"The body's, which a cheek riser fits over; the butt flares wider (stock_butt_width). Aero's page for the stock it ships (M4 Sliding Stock, APRH100033C) states 7.2 oz and no dimensions (read 2026-10-02); a distributor's '2 in' for it is behind a robots.txt that refuses us. The two figures and the patent are for the M4 pattern (a clone's table, a riser maker's fit, the Army's design): Aero's stock is that pattern, with slots in its sides where the patent's has pockets."},"stock_butt_width":{"label":"The M4 stock's width at its butt (Z), where it flares","kind":"length","measurements":[{"id":"patent","value":1.707,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-m4e1-lower 3f4478bbd4cd (US D620,067 S, the Army's design patent for an M4-pattern buttstock, sheet 3, FIG. 3 top plan, 300 dpi)","scaleRef":"the receiver extension in the same figure, 191 px across, as the standard's mil-spec OD (std.receiver_extension.milspec_od, 1.148 in): 166.4 px/in","method":"the butt's width in the plan view at its widest, 284 px (± 1), 0.18 to 0.27 in ahead of its rear face","via":"harvest"}}],"note":"The patent's rear elevation (FIG. 6), scaled by the stock's height alone, reads 1.74 at its widest: within 2%."},"stock_butt_flare":{"label":"The M4 stock's butt flare, how far ahead of the rear face it begins","kind":"length","measurements":[{"id":"patent","value":0.535,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-m4e1-lower 3f4478bbd4cd (US D620,067 S, the Army's design patent for an M4-pattern buttstock, sheet 3, FIG. 3 top plan, 300 dpi)","scaleRef":"the receiver extension in the same figure, 191 px across, as the standard's mil-spec OD (std.receiver_extension.milspec_od, 1.148 in): 166.4 px/in","method":"the last column with ink (the rear face) to the first column wider than the body, 89 px","via":"harvest"}}],"note":"From the butt's rear face forward it stays at its full width 0.23 in, then narrows to the body's by this distance."},"stock_butt_full":{"label":"The M4 stock's butt, how far ahead of the rear face it stays at full width","kind":"length","measurements":[{"id":"patent","value":0.234,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-m4e1-lower 3f4478bbd4cd (US D620,067 S, the Army's design patent for an M4-pattern buttstock, sheet 3, FIG. 3 top plan, 300 dpi)","scaleRef":"the receiver extension in the same figure, 191 px across, as the standard's mil-spec OD (std.receiver_extension.milspec_od, 1.148 in): 166.4 px/in","method":"the rear face to where the width drops from 284 px, 39 px","via":"harvest"}}]},"stock_height":{"label":"The M4 stock's height, its top to its toe","kind":"length","measurements":[{"id":"photo","value":5.179,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-m4e1-lower 4a14a1778a59 (right side, Aero's studio photo of the complete lower APAR600101)","scaleRef":"the pin frame of the complete lower's traced outline (std.ar15.pin_spacing)","method":"the traced outline's height inside the stock's box (profiles.complete, features.stock): 1.787 above the pin line to 3.392 below","via":"harvest"}},{"id":"leapers","value":5.1,"unit":"in","stated":"Height 5.1 in (130 mm)","source":{"type":"spec","publisher":"manufacturer","name":"Leapers, UTG PRO 6-Position Mil-spec Stock (RBU6BM): a clone of the M4 pattern","url":"https://www.leapers.com/products-utgpro-rbu6bm.html","retrieved":"2026-10-02","via":"harvest"}}],"adopt":{"from":"photo","reason":"Aero's own stock, in the photo the rest of the lower is traced from; the clone's figure is to a tenth."}},"stock_weight":{"label":"The M4 stock's weight on its own (Aero's M4 Sliding Stock)","kind":"mass","measurements":[{"id":"spec","value":7.2,"unit":"oz","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision","url":"https://www.aeroprecisionusa.com/m4-sliding-stock","retrieved":"2026-10-02","via":"harvest"},"note":"\"Weight(s) 7.2 oz\" on Aero's page for the stock sold on its own (APRH100033C); the complete lower's page names it \"M4 Stock - Black\". For the centre of mass (mass.lumps), not the build's weight: the complete lower's 33.25 oz counts it."}]},"rear_body_width":{"label":"The receiver's rear below the tower ring, across (Z)","kind":"length","measurements":[{"id":"rear","value":1.04,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-m4e1-lower 748bb1292dc5 (rear view, Aero's studio photo of the stripped M4E1 (the tower ring above, the magwell below))","scaleRef":"scale from aero-m4e1-lower.height = 4.079 in (y-extent 544 px → 133.4 px/in)","method":"median row width in y [-2.0, -1.3] (0.855–1.282) of the traced outline (tools/trace.py)","via":"harvest"},"note":"The rear view's outline at those heights, across: the bolt catch's bosses and the right panel, which stand 3 to 4.5 in ahead of the rear face, with the takedown lug's ears between them. Not the rear end's own width (the model review, 2026-10-05): the near end there is the body's, 0.84 in across on this photo, and the outline's waist under the ring is 0.855; the model holds the receiver behind the takedown pin to std.ar15.lower_body_width below that waist."}],"note":"From the rear view (tools/trace.py)."},"stock_top_above_pin":{"label":"The M4 stock's top above the pin line (the complete lower)","kind":"length","measurements":[{"id":"complete","value":1.787,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-m4e1-lower 4a14a1778a59 (right side, Aero's studio photo of the complete lower APAR600101, pin-framed by its pin heads)","scaleRef":"frame from the reviewed holes takedown (560.5,218.5) r=14px, pivot (944.5,216.5) r=10px (60.2 px/in, rms 0.000 in over 2 points)","method":"y_max in x [-8.6, -1.2] of the traced outline (tools/trace.py)","via":"harvest"},"note":"The M4 stock's top, above the pin line."}],"note":"From the complete lower's traced silhouette."},"buffer_kit_weight":{"label":"The carbine buffer kit's weight on its own (Aero's AR15/M4 Carbine Buffer Kit, No Stock)","kind":"mass","measurements":[{"id":"spec","value":9.8,"unit":"oz","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision","url":"https://www.aeroprecisionusa.com/ar15-buffer-kit","retrieved":"2026-10-02","via":"harvest"},"note":"\"Weight(s) 9.8 oz\" on Aero's page for the kit sold on its own: the receiver extension, carbine buffer, spring, end plate and castle nut, which the complete lower's page lists as \"Carbine Receiver Extension\" and \"AR15 Carbine Buffer and Spring\". For the centre of mass (mass.lumps), not the build's weight."}],"note":"Aero's extension alone is 3.8 oz and its carbine buffer 3.0 (their own pages, read 2026-10-02); the spring, end plate and nut make up the rest of the 9.8."},"extension_length":{"label":"The carbine receiver extension's length behind the receiver's rear face","kind":"length","measurements":[{"id":"generic","value":7.25,"unit":"in","pm":0.1,"source":{"type":"derived","expr":"{bcm-receiver-extension.tube_length}","via":"user"},"note":"A mil-spec carbine extension's length as two generic sources give it (recorded on the BCM kit: 7.25); Aero's page for its extension states no length. Places the buffer kit's weight for the centre of mass; nothing is drawn to it (the stock covers the tube)."}],"adopt":{"from":"generic","reason":"The only figure on file; Aero states none. Provisional, like the BCM kit's."}},"panel_right_out":{"label":"The right side panel's face, from the centre plane","kind":"length","measurements":[{"id":"bottom_fde","value":0.664,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-m4e1-lower ab9b1c2f8e07 (Aero's FDE gallery: the stripped receiver from below)","scaleRef":"the body's width behind the panels, 92.9 px on rows 380-420, as std.ar15.lower_body_width (0.880): 105.6 px/in","method":"the 50% edge on rows 540-580 at u 566.9, against the body's centre at u 496.8: 70.1 px","via":"harvest"}},{"id":"bottom_black","value":0.674,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-m4e1-lower 48e3b4d675cf (AT3 Tactical's gallery: the black stripped receiver from below, 1200 px)","scaleRef":"the body's width behind the panels, 137.8-138.1 px, as std.ar15.lower_body_width (0.880): 156.9 px/in","method":"u 719.6 against the centre 613.8 (carried forward: the photo is turned 0.66°); across both panels 1.331, the FDE one's 1.330","via":"harvest"}},{"id":"front","value":0.674,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-m4e1-lower 3fb9b60111c0 (Aero's stripped M4E1 from the front, 1000 x 631)","scaleRef":"the front lug's slot (std.ar15.front_lug_slot_width, .500 REF): 73 px on row 250, 146 px/in","method":"u 401.6 on rows 180-360, from the centre at u 500","via":"harvest"}}],"adopt":{"from":"bottom_fde","reason":"Two specimens, each scaled in its own plane by the TDP's body, agree; the FDE view's centre is the better defined."},"note":"It stands 0.12 in proud of the drawing's fence (0.549): Aero's own forging. The end views can't give it: the rear view's far features are shifted 0.09 sideways, and the front view's height scale reads widths 10% large."},"panel_right_rear_x":{"label":"The right side panel's face, where it begins (its ramp's foot 0.17 behind)","kind":"length","measurements":[{"id":"right","value":3.09,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/aero-m4e1-lower 30b8c6d3edf1 (Aero's stripped M4E1, right side, pin-framed)","scaleRef":"its open pin holes: 118.9 px/in; its x reads about 0.04 short (the trigger hole 1.889 against 1.928)","method":"the panel's lit edge, corrected by the photo's +0.04; its ramp from 2.92; the FDE bottom view's ramp, once placed, 2.94 to 3.20","via":"harvest"}}]},"panel_right_ramp":{"label":"The right side panel's ramp up from the body, its length along x","kind":"length","measurements":[{"id":"right","value":0.17,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/aero-m4e1-lower 30b8c6d3edf1 (Aero's stripped M4E1, right side, pin-framed)","scaleRef":"its open pin holes: 118.9 px/in; its x reads about 0.04 short (the trigger hole 1.889 against 1.928)","method":"from the ramp's foot (2.92) to the face (3.09)","via":"harvest"}}]},"panel_right_bottom_y":{"label":"The right side panel's lower edge, Y (below it the well's wall steps in)","kind":"length","measurements":[{"id":"front","value":-1.03,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/aero-m4e1-lower 3fb9b60111c0 (Aero's stripped M4E1 from the front, 1000 x 631)","scaleRef":"the front lug's slot (std.ar15.front_lug_slot_width, .500 REF): 73 px on row 250, 146 px/in","method":"the step in the right side's outline below the deck (v 175 = Y 0.245)","via":"harvest"}}]},"catch_block_front_x":{"label":"The raised block round the magazine catch on the right side, where its face ends at the front, X","kind":"length","measurements":[{"id":"stripped","value":3.64,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-m4e1-stripped-lower.catch_block_front_x}","via":"harvest"},"note":"By reference: the same receiver (Aero's page for this complete lower: \"Includes: M4E1 Stripped Lower Receiver - Anodized Black\"), read on two photos of the stripped one's right side, recorded under it with the photos, the scale and the method."}]},"catch_block_front_ramp":{"label":"The catch block's front chamfer, its length along X","kind":"length","measurements":[{"id":"stripped","value":0.16,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{aero-m4e1-stripped-lower.catch_block_front_ramp}","via":"harvest"},"note":"By reference, as catch_block_front_x."}]},"wall_right_below_panel":{"label":"The well's right wall below the panel, from the centre plane","kind":"length","measurements":[{"id":"front","value":0.56,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-m4e1-lower 3fb9b60111c0 (Aero's stripped M4E1 from the front, 1000 x 631)","scaleRef":"the front lug's slot (std.ar15.front_lug_slot_width, .500 REF): 73 px on row 250, 146 px/in","method":"the right side's outline between the panel's step and the mouth's flare","via":"harvest"}}]},"panel_left_out":{"label":"The left side's face over the magazine well, from the centre plane","kind":"length","measurements":[{"id":"front","value":0.603,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-m4e1-lower 3fb9b60111c0 (Aero's stripped M4E1 from the front, 1000 x 631)","scaleRef":"the front lug's slot (std.ar15.front_lug_slot_width, .500 REF): 73 px on row 250, 146 px/in","method":"u 588.1 on rows 230-250, 280-300 and 330-540: the face between the catch pad's two bumps","via":"harvest"}}],"note":"One view only."},"panel_left_rear_x":{"label":"The left side's face over the well, where it begins (its ramp's foot 0.08 behind)","kind":"length","measurements":[{"id":"left","value":3.03,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/aero-m4e1-lower ae10e5019d19 (Aero's stripped M4E1, left side, pin-framed)","scaleRef":"its open pin holes: 116.7 px/in; features on its wall read about +0.02 in x and y against the drawing's","method":"the face's lit rear chamfer from the deck down to Y -0.88, less the photo's +0.02; its ramp from 2.95","via":"harvest"}}]},"panel_left_ramp":{"label":"The left face's ramp up from the body, its length along x","kind":"length","measurements":[{"id":"left","value":0.08,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-m4e1-lower ae10e5019d19 (Aero's stripped M4E1, left side, pin-framed)","scaleRef":"its open pin holes: 116.7 px/in; features on its wall read about +0.02 in x and y against the drawing's","method":"from the ramp's foot (2.95) to the face (3.03)","via":"harvest"}}]},"catch_pad_out":{"label":"The pad round the magazine catch's slot (left), its face from the centre plane","kind":"length","measurements":[{"id":"bottom_fde","value":0.666,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-m4e1-lower ab9b1c2f8e07 (Aero's FDE gallery: the stripped receiver from below)","scaleRef":"the body's width behind the panels, 92.9 px on rows 380-420, as std.ar15.lower_body_width (0.880): 105.6 px/in","method":"u 426.45 on rows 540-626 (X 3.5 to 4.4), one plane within 0.01 throughout","via":"harvest"}},{"id":"bottom_black","value":0.656,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-m4e1-lower 48e3b4d675cf (AT3 Tactical's gallery: the black stripped receiver from below, 1200 px)","scaleRef":"the body's width behind the panels, 137.8-138.1 px, as std.ar15.lower_body_width (0.880): 156.9 px/in","method":"u 510.8","via":"harvest"}},{"id":"front","value":0.681,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-m4e1-lower 3fb9b60111c0 (Aero's stripped M4E1 from the front, 1000 x 631)","scaleRef":"the front lug's slot (std.ar15.front_lug_slot_width, .500 REF): 73 px on row 250, 146 px/in","method":"the two bumps either side of the slot at u 599.4","via":"harvest"}}],"adopt":{"from":"bottom_fde","reason":"One plane over its length on the FDE view; the black specimen's and the front view's agree within their ±."}},"catch_pad_top_y":{"label":"The catch pad's upper edge, Y","kind":"length","measurements":[{"id":"left","value":-0.3,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/aero-m4e1-lower ae10e5019d19 (Aero's stripped M4E1, left side, pin-framed)","scaleRef":"its open pin holes: 116.7 px/in; features on its wall read about +0.02 in x and y against the drawing's","method":"the pad's outline above the slot; the front view's upper bump at Y -0.34 to -0.41","via":"harvest"}}]},"catch_pad_bottom_y":{"label":"The catch pad's lower edge, Y","kind":"length","measurements":[{"id":"left","value":-0.78,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/aero-m4e1-lower ae10e5019d19 (Aero's stripped M4E1, left side, pin-framed)","scaleRef":"its open pin holes: 116.7 px/in; features on its wall read about +0.02 in x and y against the drawing's","method":"the pad's outline below the slot; the front view's lower bump at Y -0.68 to -0.75","via":"harvest"}}]},"catch_pad_front_x":{"label":"The catch pad's rounded front end, X","kind":"length","measurements":[{"id":"left","value":4.56,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-m4e1-lower ae10e5019d19 (Aero's stripped M4E1, left side, pin-framed)","scaleRef":"its open pin holes: 116.7 px/in; features on its wall read about +0.02 in x and y against the drawing's","method":"the outline's front end at 4.58, less the photo's +0.02","via":"harvest"}}]},"catch_pad_rear_x":{"label":"The catch pad's rear end, X","kind":"length","measurements":[{"id":"slot","value":3.048,"unit":"in","source":{"type":"derived","expr":"{std.ar15.mag_catch_slot_rear_x}","via":"harvest"}}],"note":"Hidden in the photos; taken at the catch slot's rear end (std.ar15.mag_catch_slot_rear_x), which the pad must enclose."},"bolt_catch_boss_out":{"label":"Aero's bolt catch bosses, their face from the centre plane (left)","kind":"length","measurements":[{"id":"bottom_fde","value":0.708,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-m4e1-lower ab9b1c2f8e07 (Aero's FDE gallery: the stripped receiver from below)","scaleRef":"the body's width behind the panels, 92.9 px on rows 380-420, as std.ar15.lower_body_width (0.880): 105.6 px/in","method":"u 422.05 on rows 490-530","via":"harvest"}},{"id":"bottom_black","value":0.703,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-m4e1-lower 48e3b4d675cf (AT3 Tactical's gallery: the black stripped receiver from below, 1200 px)","scaleRef":"the body's width behind the panels, 137.8-138.1 px, as std.ar15.lower_body_width (0.880): 156.9 px/in","method":"u 502.5 to 503.3","via":"harvest"}},{"id":"front","value":0.72,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-m4e1-lower 3fb9b60111c0 (Aero's stripped M4E1 from the front, 1000 x 631)","scaleRef":"the front lug's slot (std.ar15.front_lug_slot_width, .500 REF): 73 px on row 250, 146 px/in","method":"rows 200-210","via":"harvest"}}],"adopt":{"from":"bottom_fde","reason":"Two specimens on their own body's scale agree within 0.005; the front view within its ±."},"note":"Between the drawing's 0.618 and the reference CAD model's 0.727: Aero's forging."},"bolt_catch_boss_rear_x":{"label":"Aero's rear bolt catch boss, its rear end, X","kind":"length","measurements":[{"id":"bottom_fde","value":3.01,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/aero-m4e1-lower ab9b1c2f8e07 (Aero's FDE gallery: the stripped receiver from below)","scaleRef":"the body's width behind the panels, 92.9 px on rows 380-420, as std.ar15.lower_body_width (0.880): 105.6 px/in","method":"the boss's rear end, the view placed so the slot's notch between the bosses (3.15-3.29) lands on the drawing's slot (3.203-3.375): +0.07; the left photo agrees within 0.05","via":"harvest"}}]},"bolt_catch_boss_front_x":{"label":"Aero's front bolt catch boss, its front end, X","kind":"length","measurements":[{"id":"bottom_fde","value":3.52,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/aero-m4e1-lower ab9b1c2f8e07 (Aero's FDE gallery: the stripped receiver from below)","scaleRef":"the body's width behind the panels, 92.9 px on rows 380-420, as std.ar15.lower_body_width (0.880): 105.6 px/in","method":"the boss's front end, placed as bolt_catch_boss_rear_x","via":"harvest"}}]},"bolt_catch_boss_bottom_y":{"label":"Aero's bolt catch bosses, their lower ends, Y (they rise to the deck)","kind":"length","measurements":[{"id":"left","value":-0.02,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/aero-m4e1-lower ae10e5019d19 (Aero's stripped M4E1, left side, pin-framed)","scaleRef":"its open pin holes: 116.7 px/in; features on its wall read about +0.02 in x and y against the drawing's","method":"the bosses' lower edges against the left face, less the photo's +0.02","via":"harvest"}}]},"front_view_lug_slot":{"label":"The front lug's slot as the front view's height scale reads it","kind":"length","measurements":[{"id":"front","value":0.549,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/aero-m4e1-lower 3fb9b60111c0 (Aero's stripped M4E1 from the front, 1000 x 631)","scaleRef":"the side's height, as profiles.front is scaled: 132.9 px/in","method":"the slot between the pivot lug's ears, 73 px on row 250 (72.5 on a 4x gridded crop)","via":"harvest"}}],"note":"The front view (profiles.front) was scaled by the side's height, which runs to the far tower: its widths read large by this over the slot's .500 (std.ar15.front_lug_slot_width)."},"ear_right_out":{"label":"The pivot lug's right ear, its outer face from the centre plane (the slot's middle)","kind":"length","measurements":[{"id":"front","value":0.519,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/aero-m4e1-lower 3fb9b60111c0 (Aero's stripped M4E1 from the front, 1000 x 631)","scaleRef":"the slot between the ears, face to face (std.ar15.front_lug_slot_width, .500 REF): 74.2 px on rows 162-184 (75.1 at the top of the round to 73.2 at the pin's height), 148.5 px/in. Checked two ways: the deck to the slot's floor (rows 150.85 to 278.0) is 0.8575 by the pin-framed side outline, 148.3 px/in; and the right panel's face, 0.37 in behind the ears' fronts, reads 0.668 at the slot's scale (u 400.8 on rows 176-198) against 0.664 and 0.674 on the two bottom views (panel_right_out). The lens is 120 in away or more (the tower's ring, 7.5 in behind, is 194.6 px across: 139.8 px/in if it is the standard's 1.392, more if it is narrower), so the 0.4 in of depth between the ears' fronts and the panel's end is 0.3% at most","method":"each row's steepest step inside a 6 px window, sub-pixel, rows 162-184: the ear's outer edge at u 422.9 (422.4 to 423.2), the slot's middle at u 500.0: 77.1 px. The ± covers the edge (0.5 px), which side of its break the step is taken at (0.7 px), the slot's width down the rows (1.3%) and the second specimen","via":"harvest"}},{"id":"front_fde","value":0.525,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/aero-m4e1-lower a3ae8dc15471 (Aero's FDE stripped M4E1 from the front, the black view's pose)","scaleRef":"the slot between the ears, face to face (std.ar15.front_lug_slot_width, .500 REF): 73.1 px on rows 176-190, 146.2 px/in","method":"as the black view's, rows 176-190 (clear of the detent's hole): the ear's outer edge at u 425.3, the slot's middle at u 502.0: 76.8 px","via":"harvest"}},{"id":"detent","value":0.53,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/aero-m4e1-lower 3fb9b60111c0 (Aero's stripped M4E1 from the front, 1000 x 631)","scaleRef":"the slot between the ears, face to face (std.ar15.front_lug_slot_width, .500 REF): 74.2 px on rows 162-184, 148.5 px/in","method":"the face a pivot pin's head stands on, from the pivot detent's hole beside the ear: the hole's middle is 86.7 px from the slot's middle on row 186, 0.584 in (0.582 on the FDE specimen, a3ae8dc15471), and the Army's pin has its detent hole .0535 ± .0025 outboard of its head's shoulder (TDP drawing 8448621, Pin, Receiver Pivot, Section F-F: the hole and the groove are in the side the head's flat is on; user-supplied scan, references/tdp lpk-up-p102). The ± covers the hole's middle (1 px), the scale and how close the shoulder seats","via":"harvest"}}],"adopt":{"from":"front","reason":"The black photo, the front profile's own, the edge itself; the FDE specimen in the same pose agrees within 0.006, and the detent's hole puts the head's seat within 0.011 of it."},"note":"The ear is 0.27 in thick (this less half the slot). One width down the rows read (Y +0.17 to +0.02, the nose's lit round) and on up to the deck: no taper, and no chamfer wider than a pixel (0.007 in). Outboard of it the right panel's front end is a shelf 0.20 in behind the pin, with the pivot detent's hole in it: 0.10 in across, its middle 0.58 from the centre plane at the pin's height (u 406.0 to 420.6 on row 186; 0.09 and 0.58 on the FDE specimen), its inner edge 0.016 from this face. A pivot pin's head stands on this face, in the corner beside that shelf: Brownells' photo of the complete lower from below and to the right (references/aero-m4e1-lower b254c9c8af74) has it there, its top about level with the right panel's face (this plus the head's .18 is 0.699; the panel is 0.664). A round .400 head there reaches 0.006 in into the shelf's face; the flat on the Army's pin's head (.1355 from the axis, drawing 8448621) clears it by 0.06, and is the side its detent holes are in: the flat faces the shelf. That pin is 1.132 under its head: from this face its plain end is 0.07 in proud of the left ear's. The Army's own right ear is 0.449 from the centre plane (ears_width's note): Aero's is 0.07 further out, and so is its detent's hole (the drawing's pin puts a mil-spec one .0535 past 0.449, at 0.50)."},"ear_left_out":{"label":"The pivot lug's left ear, its outer face from the centre plane (the slot's middle)","kind":"length","measurements":[{"id":"front","value":0.542,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/aero-m4e1-lower 3fb9b60111c0 (Aero's stripped M4E1 from the front, 1000 x 631)","scaleRef":"the slot between the ears, face to face (std.ar15.front_lug_slot_width, .500 REF): 74.2 px on rows 162-184, 148.5 px/in; its checks are ear_right_out's","method":"each row's steepest step inside a 6 px window, sub-pixel, rows 162-184: the ear's outer edge at u 580.5 (580.3 to 580.5), the slot's middle at u 500.0: 80.5 px","via":"harvest"}},{"id":"front_fde","value":0.544,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aero-m4e1-lower a3ae8dc15471 (Aero's FDE stripped M4E1 from the front, the black view's pose)","scaleRef":"the slot between the ears, face to face (std.ar15.front_lug_slot_width, .500 REF): 73.1 px on rows 176-190, 146.2 px/in","method":"as the black view's, rows 176-190: the ear's outer edge at u 581.5 (a step of 22 to 28 of 255: faint), the slot's middle at u 502.0: 79.5 px","via":"harvest"}}],"adopt":{"from":"front","reason":"The black photo, the front profile's own; the FDE specimen agrees within 0.002."},"note":"The ear is 0.29 in thick, 0.02 more than the right one on both specimens (3.3 and 2.7 px). Read as the right ear's; its edge is the fainter (the left side's face beside it is lit like the ear). The Army's drawing has this face in the plane of the magazine well's left wall, 0.549 (ears_width's note): Aero's reads there, within its ±."},"ears_width":{"label":"The pivot lug across its two ears","kind":"length","measurements":[{"id":"faces","value":1.061,"unit":"in","pm":0.017,"source":{"type":"derived","expr":"{.ear_right_out} + {.ear_left_out}","via":"harvest"}},{"id":"front","value":1.062,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aero-m4e1-lower 3fb9b60111c0 (Aero's stripped M4E1 from the front, 1000 x 631)","scaleRef":"the slot between the ears, face to face (std.ar15.front_lug_slot_width, .500 REF): 74.2 px on rows 162-184, 148.5 px/in","method":"outer edge to outer edge, 157.6 px (157.3 to 158.0 down the rows): 2.12 slots","via":"harvest"}},{"id":"front_fde","value":1.069,"unit":"in","pm":0.017,"source":{"type":"photo","photo":"references/aero-m4e1-lower a3ae8dc15471 (Aero's FDE stripped M4E1 from the front, the black view's pose)","scaleRef":"the slot between the ears, face to face (std.ar15.front_lug_slot_width, .500 REF): 73.1 px on rows 176-190, 146.2 px/in","method":"outer edge to outer edge, 156.3 px: 2.14 slots","via":"harvest"}}],"adopt":{"from":"faces","reason":"The two faces as the model has them, each from the slot's middle; the photos' own spans agree within 0.008."},"note":"The Army's lug is not two ears alike either: its right ear is .198 ± .004 thick, so 0.449 from the centre plane (TDP drawing 8448608, Receiver, Lower, sheet 1, plan view at the front lug: from datum AH, the ear's inside face, itself .251 ± .004 from the centre plane AJ; user-supplied scan, references/tdp p64), and its left ear's outer face runs on from the magazine well's left wall (std.ar15.magwell_outside_width / 2, 0.549; not dimensioned at the ear), 1.00 across. Aero's left ear is that within the reading; its right ear is 0.07 in thicker than the Army's."},"ear_right_rear_x":{"label":"The right ear's outer face, where it begins: the right panel's front end, X","kind":"length","measurements":[{"id":"right","value":6.18,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aero-m4e1-lower 30b8c6d3edf1 (Aero's stripped M4E1, right side, pin-framed)","scaleRef":"its open pin holes (takedown 179.4, pivot 936.6): 118.8 px/in; read from the pivot hole, 23 px away","method":"the dark line the step casts, two pixels wide, its panel-side edge at u 913.5 on rows 204-264 (Y +0.21 to -0.29): 23.1 px behind the pivot hole's centre, 0.194 in","via":"harvest"}}],"note":"A square step, 0.145 in deep (panel_right_out less ear_right_out), the pivot detent's hole in it. It runs the lug's height: from the deck down to Y -0.29 on the photo, where the lug's underside is 0.1 below it."},"ear_left_rear_x":{"label":"The left ear's outer face, where it begins: the foot of the ramp up to the left side's face, X (at the pin's height)","kind":"length","measurements":[{"id":"left","value":6.15,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-m4e1-lower ae10e5019d19 (Aero's stripped M4E1, left side, pin-framed)","scaleRef":"its open pin holes (takedown 819.0, pivot 73.8): 116.9 px/in; read from the pivot hole, 26 px away","method":"the ramp is a dark band beside the ear: its ear-side edge at u 97.5 on row 244 (Y +0.20; X 6.172), 100.5 on row 258 (Y +0.08; 6.147), 101.5 on row 264 (Y +0.03; 6.138)","via":"harvest"}}],"note":"No square step on the left: a ramp, which leans back as it goes down (its foot at X 6.17 by the deck, 6.14 at the pin line) and is gone below the pin line, where the ear's face runs on into the well's front corner. One figure, for an upright ramp; the ± is its lean."},"ear_left_ramp":{"label":"The ramp from the left ear's face up to the left side's face, its length along X","kind":"length","measurements":[{"id":"left","value":0.06,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-m4e1-lower ae10e5019d19 (Aero's stripped M4E1, left side, pin-framed)","scaleRef":"its open pin holes (takedown 819.0, pivot 73.8): 116.9 px/in","method":"the dark band's width: 6 px on row 244, 7 on row 258, 9 on row 264 (0.05 to 0.08 in); it rises 0.06 across (panel_left_out less ear_left_out)","via":"harvest"}}]},"stock_lever_width":{"label":"The stock's adjustment lever, its width across (Z)","kind":"length","measurements":[{"id":"patent","value":0.757,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-m4e1-lower 3f4478bbd4cd (US D620,067 S, sheet 3: FIG. 3 top and FIG. 4 bottom plan, the patent office's copy)","scaleRef":"the receiver extension beside it in FIG. 3 (broken lines: its environment, used as the scale), 191 px as the extension's 1.148 in: 166.4 px/in; the stock's body there reads 1.448 against stock_width","method":"the lever's two outer lines in FIG. 4, u 1617 and 1742","via":"harvest"}},{"id":"model","value":0.741,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Stock_Latch.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of the USGI M4 stock's parts)","method":"a U-channel over its walls (0.108 thick), 2.79 long","via":"user"}}],"adopt":{"from":"patent","reason":"The patent's drawing of the stock; the model, 2% under it, beside it."}},"stock_lock_pin_d":{"label":"The lever's lock pin, the diameter of its end that hangs below the lever","kind":"length","measurements":[{"id":"photo","value":0.417,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-m4e1-lower 4a14a1778a59 (right side, Aero's studio photo of the complete lower APAR600101, pin-framed by its pin heads)","scaleRef":"its pin heads, 6.375 in apart: 60.24 px/in, the stock where the photo has it","method":"the pin's end, the box px 306-331 on the stock_lock_pin feature","via":"harvest"}},{"id":"model","value":0.437,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Stock_Bolt_Nut.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of the USGI M4 stock's parts)","method":"its nut, 0.437 across and 0.316 tall: the stub under the lever (the pin itself, Stock_Bolt.step, d 0.307)","via":"user"}}],"adopt":{"from":"photo","reason":"What hangs below Aero's lever as its photo shows it; the model's nut beside it."}},"sling_loop_wire_d":{"label":"The sling loop's wire diameter","kind":"length","measurements":[{"id":"patent","value":0.16,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-m4e1-lower 3f4478bbd4cd (US D620,067 S, sheet 3: FIG. 3 top and FIG. 4 bottom plan, the patent office's copy)","scaleRef":"the receiver extension beside it in FIG. 3 (broken lines: its environment, used as the scale), 191 px as the extension's 1.148 in: 166.4 px/in; the stock's body there reads 1.448 against stock_width","method":"the loop's band in FIG. 4","via":"harvest"}},{"id":"model","value":0.178,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Stock_Swivel.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of the USGI M4 stock's parts)","method":"its wire's diameter","via":"user"}}],"adopt":{"from":"patent","reason":"The patent's (D49: the model stays beside it, never adopted over it); they agree within its ±."}},"sling_loop_width":{"label":"The sling loop's width across (Z), outside","kind":"length","measurements":[{"id":"patent","value":1.785,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-m4e1-lower 3f4478bbd4cd (US D620,067 S, sheet 3: FIG. 3 top and FIG. 4 bottom plan, the patent office's copy)","scaleRef":"the receiver extension beside it in FIG. 3 (broken lines: its environment, used as the scale), 191 px as the extension's 1.148 in: 166.4 px/in; the stock's body there reads 1.448 against stock_width","method":"the loop's outer lines in FIG. 4, u 1529 and 1826","via":"harvest"}},{"id":"model","value":1.7,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Stock_Swivel.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of the USGI M4 stock's parts)","method":"a stadium 1.70 by 0.688 outside","via":"user"}}],"adopt":{"from":"patent","reason":"The patent's drawing; the model, 5% narrower, kept beside it."}},"sling_loop_depth":{"label":"The sling loop's depth, outside (the short side of its stadium)","kind":"length","measurements":[{"id":"model","value":0.688,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Stock_Swivel.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of the USGI M4 stock's parts)","method":"a stadium 1.70 by 0.688 outside","via":"user"}}]},"stock_slot_length":{"label":"The slots in the stock's sides, each one's length","kind":"length","measurements":[{"id":"photo","value":1.03,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-m4e1-lower 4a14a1778a59 (right side, Aero's studio photo of the complete lower APAR600101, pin-framed by its pin heads)","scaleRef":"its pin heads, 6.375 in apart: 60.24 px/in, the stock where the photo has it","method":"the slots' ends along their rows (.cache/research/aero-lower/stock_rows.py)","via":"harvest"}},{"id":"model","value":1,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Stock_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of the USGI M4 stock's parts)","method":"five columns 1.000 long","via":"user"}}],"adopt":{"from":"photo","reason":"Aero's own stock; the model's USGI one beside it."}},"stock_slot_pitch":{"label":"The slots in the stock's sides, their pitch along it","kind":"length","measurements":[{"id":"photo","value":1.14,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-m4e1-lower 4a14a1778a59 (right side, Aero's studio photo of the complete lower APAR600101, pin-framed by its pin heads)","scaleRef":"its pin heads, 6.375 in apart: 60.24 px/in, the stock where the photo has it","method":"the columns' centres, X -8.03 to -2.43 over four pitches","via":"harvest"}},{"id":"model","value":1.13,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Stock_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of the USGI M4 stock's parts)","method":"five columns on a 1.130 pitch","via":"user"}}],"adopt":{"from":"photo","reason":"Aero's own stock."}},"stock_slot_columns":{"label":"The columns of slots in each side","kind":"count","measurements":[{"id":"photo","value":5,"unit":"count","source":{"type":"photo","photo":"references/aero-m4e1-lower 4a14a1778a59 (right side, Aero's studio photo of the complete lower APAR600101, pin-framed by its pin heads)","scaleRef":"its pin heads, 6.375 in apart: 60.24 px/in, the stock where the photo has it","method":"counted (the fourth faint; the model has five)","via":"harvest"}}]},"stock_slot_rear_x":{"label":"The rearmost column's rear end, X (where the photo has the stock)","kind":"length","measurements":[{"id":"photo","value":-8.03,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-m4e1-lower 4a14a1778a59 (right side, Aero's studio photo of the complete lower APAR600101, pin-framed by its pin heads)","scaleRef":"its pin heads, 6.375 in apart: 60.24 px/in, the stock where the photo has it","method":"the first column's rear end","via":"harvest"}}]},"stock_slot_rows_x":{"label":"Where along the stock the rows' heights are read, X","kind":"length","measurements":[{"id":"photo","value":-7.6,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-m4e1-lower 4a14a1778a59 (right side, Aero's studio photo of the complete lower APAR600101, pin-framed by its pin heads)","scaleRef":"its pin heads, 6.375 in apart: 60.24 px/in, the stock where the photo has it","method":"the station of the rows' readings, in the first column","via":"harvest"}}]},"stock_slot_row1_y":{"label":"The upper row of slots, its centre at X -7.6, Y","kind":"length","measurements":[{"id":"photo","value":0.47,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-m4e1-lower 4a14a1778a59 (right side, Aero's studio photo of the complete lower APAR600101, pin-framed by its pin heads)","scaleRef":"its pin heads, 6.375 in apart: 60.24 px/in, the stock where the photo has it","method":"the row from Y 0.39 to 0.55 at X -7.6: 0.33 to 0.49 below the tube's axis, where the model's upper row is","via":"harvest"}}]},"stock_slot_row2_y":{"label":"The lower row of slots, its centre at X -7.6, Y","kind":"length","measurements":[{"id":"photo","value":0.07,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-m4e1-lower 4a14a1778a59 (right side, Aero's studio photo of the complete lower APAR600101, pin-framed by its pin heads)","scaleRef":"its pin heads, 6.375 in apart: 60.24 px/in, the stock where the photo has it","method":"the row from Y -0.005 to 0.145 at X -7.6","via":"harvest"}}],"note":"0.14 below where the reference model has its lower row: Aero's pattern differs there."},"stock_slot_slope":{"label":"The rows of slots, their fall toward the front (an angle below the horizontal)","kind":"angle","measurements":[{"id":"photo","value":-0.92,"unit":"deg","pm":0.23,"source":{"type":"photo","photo":"references/aero-m4e1-lower 4a14a1778a59 (right side, Aero's studio photo of the complete lower APAR600101, pin-framed by its pin heads)","scaleRef":"its pin heads, 6.375 in apart: 60.24 px/in, the stock where the photo has it","method":"the rows' centres along X fall 0.016 in an inch toward the front, as the stock's top edge in the same outline does","via":"harvest"}}]},"stock_slot_height":{"label":"The slots in the stock's sides, each one's height","kind":"length","measurements":[{"id":"photo","value":0.155,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-m4e1-lower 4a14a1778a59 (right side, Aero's studio photo of the complete lower APAR600101, pin-framed by its pin heads)","scaleRef":"its pin heads, 6.375 in apart: 60.24 px/in, the stock where the photo has it","method":"the rows' heights as they show (their edges' bevels and the blur in it)","via":"harvest"}},{"id":"model","value":0.13,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Stock_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of the USGI M4 stock's parts)","method":"each row 0.130 tall","via":"user"}}],"adopt":{"from":"photo","reason":"Aero's own, as it shows; the model's 0.13 (its edges' bevels not counted) beside it."}},"stock_slot_depth_upper":{"label":"The upper row of slots, their depth into the side","kind":"length","measurements":[{"id":"model","value":0.13,"unit":"in","pm":0.04,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Stock_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of the USGI M4 stock's parts)","method":"its upper row's floor, a cylinder r 0.675 about the tube's axis: 0.09 to 0.18 deep","via":"user"}}],"note":"Provisional: no source gives Aero's own depth; the USGI stock's."},"stock_slot_depth_lower":{"label":"The lower row of slots, their depth into the side","kind":"length","measurements":[{"id":"model","value":0.25,"unit":"in","pm":0.05,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Stock_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of the USGI M4 stock's parts)","method":"its lower row cut in to x 0.34-0.36 from the middle: about 0.25 deep","via":"user"}}],"note":"Provisional: no source gives Aero's own depth; the USGI stock's, whose lower row isn't where Aero's is."}}},{"subject":"aero-m4e1-stripped-lower","title":"Aero Precision M4E1 Stripped Lower Receiver - Anodized Black (APAR600001C)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"aero","value":8.35,"unit":"oz","stated":"Weight(s) 8.35","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision","url":"https://www.aeroprecisionusa.com/m4e1-stripped-lower-receiver-anodized-black","retrieved":"2026-10-12","via":"harvest"},"note":"Aero's specifications table on the product's page: \"Compatibility Works with standard AR15 components and magazines / Weight(s) 8.35 / Other Rear takedown pin detent hole is threaded for a 4-40 set screw.\" No unit is stated; ounces is this ledger's reading (the entry's note)."},{"id":"sportsmans","value":8.61,"unit":"oz","stated":"Weight 8.61oz","source":{"type":"spec","publisher":"retailer","name":"Sportsman's Warehouse","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/gun-parts-accessories/gun-parts-magazines/rifle-parts/receivers-lowers/aero-precision-m4e1-anodized-black-stripped-lower-receiver/p/1628378","retrieved":"2026-10-12","via":"harvest"},"note":"The seller's specifications for MPN APAR600001C (its item 1628378): \"Material 7075 Aluminum ... Weight 8.61oz\". A seller's page: not Aero's figure, and not said to be a weighing."},{"id":"scheels","value":8.61,"unit":"oz","stated":"Weight: 8.61 oz","source":{"type":"spec","publisher":"retailer","name":"Scheels","url":"https://www.scheels.com/p/aero-precision-m4e1-stripped-ar-15-lower-receiver/19359-APAR600001C","retrieved":"2026-10-12","via":"harvest"},"note":"Scheels' copy of Aero's own table, row for row (\"Compatibility: Works with standard AR15 components and magazines / Weight: 8.61 oz / Other: Rear takedown pin detent hole is threaded for a 4-40 set screw.\"), with another figure in the weight's row and a unit."},{"id":"dirtybird","value":8.48,"unit":"oz","stated":"Weight 8.48 oz","source":{"type":"spec","publisher":"retailer","name":"Dirty Bird Industries","url":"https://dirtybirdusa.com/products/aero-precision-m4e1-stripped-lower-receiver-2/","retrieved":"2026-10-12","via":"harvest"},"note":"Dirty Bird's \"Additional information\" table (\"Weight 8.48 oz / Color Black, FDE, Kodiak Brown, OD Green Anodized\"), and its product markup's weight (8.48, unit code ONZ): one page for four finishes. A shop's product-weight field."},{"id":"dirtybird-faq","value":8.61,"unit":"oz","stated":"It weighs approximately 8.61 oz.","source":{"type":"spec","publisher":"retailer","name":"Dirty Bird Industries","url":"https://dirtybirdusa.com/products/aero-precision-m4e1-stripped-lower-receiver-2/","retrieved":"2026-10-12","via":"harvest"},"note":"The same page's own questions and answers: \"What is the weight of the M4E1 Stripped Lower Receiver? It weighs approximately 8.61 oz.\" It disagrees with the page's table."}],"adopt":{"from":"aero","reason":"The maker's own table, the same figure on all seven finishes' pages. Its unit is this ledger's reading, and the sellers' 8.61 oz (two shops, and a third's FAQ) is 3% more: the conflict stands, and nothing on file weighed one to settle it."},"note":"THREE PUBLISHED FIGURES, AND THEY DISAGREE. Aero's own table says 8.35 and names no unit, on this page and on every other finish's (FDE Cerakote, OD Green Anodized and Cerakote, Kodiak Brown, Sniper Grey Cerakote, Uncoated: each read on its harvested page); its complete lower's table, the same row, says \"Weight(s) 33.25 oz\", and the sellers below give this receiver in ounces within 3% of 8.35, so the figure is taken as ounces. Sportsman's Warehouse and Scheels say 8.61 oz, Dirty Bird's table 8.48 oz and its own FAQ on the same page 8.61. Nobody on file weighed one. BESIDE THEM, the model's metal: the closed volume of app/public/models/aero-m4e1-stripped-lower.glb (5.878 cubic inches, the manifest's volume_in3) as 7075 (std.density.aluminium_7075, 1.632 oz to the cubic inch) is 9.59 oz: MORE METAL THAN ANY PUBLISHED FIGURE, by 11 to 15%. The model is a hull of the receiver's outlines: its magazine well's walls are as thick as the outside faces read on the photos leave them over the standard well (0.11 to 0.15 in, where a mil-spec well's are a tenth) with the mouth's flare carried up their lower half, its ring is bored at the extension's size and not the thread's, and whatever the forging has lightened inside shows in no view on file. The model's volume is not this receiver's weight and is not used as one; app/tests/aero-m4e1-stripped-lower.test.ts holds the figure said here to the model, so a rebuilt model that changes it says so."},"width":{"label":"Receiver maximum width (Z)","kind":"length","measurements":[{"id":"complete","value":1.374,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{aero-m4e1-lower.width}","via":"harvest"},"note":"The same receiver: Aero's complete lower's page lists what it is built on, \"Includes: M4E1 Stripped Lower Receiver - Anodized Black / M4 Stock - Black / A2 Grip - Black / Mil-spec Lower Parts Kit / Carbine Receiver Extension / AR15 Carbine Buffer and Spring\" (https://www.aeroprecisionusa.com/m4e1-complete-lower-a2-grip-m4-stock-black, read on the harvested copy 2026-10-12). Its widest, across the right panel's face and the left bosses' face at the deck, as read there on two specimens' bottom views (its own entry has three readings and their conflict). No page states a width. IN CONFLICT THERE, and so here: its readings are front 1.558, faces 1.374, front-own-scale 1.418; the one adopted there (faces) is the figure taken."}]},"buffer_axis_above_pin":{"label":"Receiver extension (bore) axis above the takedown pin centre","kind":"length","measurements":[{"id":"std","value":0.8775,"unit":"in","pm":0.0015,"source":{"type":"derived","expr":"{std.ar15.bore_axis_y}","via":"harvest"},"note":"Aero, of the M4E1 lower: \"This custom-designed enhanced forging is machined from 7075-T6 Aluminum and compatible with all mil-spec AR15 parts\" (its page). The threaded hole's centre is the Army drawing's (.629 above the deck), as the complete lower's entry has it."}]},"magazine_seat_x":{"label":"Magazine seat, X (a seated magazine's frame origin ahead of the takedown pin)","kind":"length","measurements":[{"id":"complete","value":3.4915,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{aero-m4e1-lower.magazine_seat_x}","via":"harvest"},"note":"By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method). A standard well inside (Aero: \"Works with standard AR15 components and magazines\"; its \"Increased Magwell Flare\" is the mouth): where a magazine seats in a mil-spec well, from the Army drawing's well and catch slot. No photo of a magazine seated in an M4E1 is on file."}]},"magazine_seat_y":{"label":"Magazine seat, Y (the feed-lip top of a seated magazine)","kind":"length","measurements":[{"id":"complete","value":1.003,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{aero-m4e1-lower.magazine_seat_y}","via":"harvest"},"note":"By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method). As magazine_seat_x: the standard well's and the catch's, a check and not this receiver's outside."}]},"grip_mating_y":{"label":"Receiver underside behind the grip's lug (where a grip's flat top bears), Y, as the side outline reads it","kind":"length","measurements":[{"id":"outline","value":-1.063,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-m4e1-stripped-lower 30b8c6d3edf1 (right side, Aero's studio photo of the stripped M4E1, pin-framed by its open holes)","scaleRef":"frame from the reviewed holes takedown (179.5,230.5) r=14px, pivot (937.5,228.5) r=8px (118.9 px/in, rms 0.000 in over 2 points)","method":"y_min in x [-0.26, -0.15] of the traced outline (tools/trace.py)","via":"harvest"},"note":"The outline's level stretch just behind the grip's lug (and behind the set screw's end, which stands out of the lug's rear from X -0.13): this receiver's own reading of where a grip's flat top bears. The seat itself is the Army drawing's (grip_seat_y, -1.0695)."}],"note":"The outline's short level stretch between the rear underside's sweep and the lug: this receiver's own reading of the plane a grip's top bears on. The seat itself is the drawing's (grip_seat_y). Filled by the trace (tools/trace.py, the seed's `right` spec)."},"grip_seat_y":{"label":"Grip seat, Y (the underside a grip's flat top bears on, at the takedown pin's X)","kind":"length","measurements":[{"id":"tdp","value":-1.0695,"unit":"in","pm":0.0115,"source":{"type":"derived","expr":"{std.ar15.deck_y} - {std.ar15.grip_seat_below_deck}","via":"harvest"},"note":"Aero, of the M4E1 lower: \"This custom-designed enhanced forging is machined from 7075-T6 Aluminum and compatible with all mil-spec AR15 parts\" (its page). The flat the lug hangs from is the drawing's, 1.318 ±.010 below the deck: a grip chosen in its own slot hangs from here. (NOT taken from the complete lower's entry of this name, which holds -1.443: the lowest point of the silhouette under the takedown pin, which is the lug's sloped face, 0.37 in below the seat. Nothing mates there on that part, whose grip is its own; said in this part's report.)"},{"id":"outline","value":-1.063,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{.grip_mating_y}","via":"harvest"},"note":"This receiver's own side photo, by the traced outline: the level stretch just behind the lug (grip_mating_y), 0.007 above the drawing's."}],"adopt":{"from":"tdp","reason":"The drawing dimensions it, Aero says the forging takes mil-spec parts, and this receiver's outline reads the stretch behind the lug on it within a pixel."}},"trigger_guard_front_x":{"label":"Trigger guard front ear hole, X","kind":"length","measurements":[{"id":"tdp","value":3.3425,"unit":"in","pm":0.007,"source":{"type":"derived","expr":"{std.ar15.trigger_guard_front_x}","via":"harvest"},"note":"Where a mil-spec lower's front ear hole is (the Army drawing's). THIS RECEIVER HAS NO EARS: its trigger guard is part of the forging (Aero: \"Integrated Trigger Guard - Eliminates the possibility of breaking the trigger guard tabs by integrating the trigger guard into the lower\"), so the slot is occupied and nothing pins here; the figure frames the anchor, as the category asks of a lower with an integral guard."}]},"trigger_guard_front_y":{"label":"Trigger guard front ear hole, Y","kind":"length","measurements":[{"id":"tdp","value":-2.18,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{std.ar15.trigger_guard_rear_y}","via":"harvest"},"note":"As trigger_guard_front_x: the drawing's two guard holes are on one centre line, 2.18 below the takedown pin. No hole is there on this receiver."}]},"trigger_guard_rear_x":{"label":"Trigger guard rear ear hole, X","kind":"length","measurements":[{"id":"tdp","value":1.4985,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{std.ar15.trigger_guard_rear_x}","via":"harvest"},"note":"As trigger_guard_front_x: the drawing's place for the rear ear's roll pin. No hole is there on this receiver (its side photos show none)."}]},"trigger_guard_rear_y":{"label":"Trigger guard rear ear hole, Y","kind":"length","measurements":[{"id":"tdp","value":-2.18,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{std.ar15.trigger_guard_rear_y}","via":"harvest"},"note":"As trigger_guard_rear_x."}]},"trigger_pin_x":{"label":"Trigger pin hole centre, X","kind":"length","measurements":[{"id":"tdp","value":1.928,"unit":"in","pm":0.004,"source":{"type":"derived","expr":"{std.ar15.trigger_pin_x}","via":"harvest"},"note":"Aero, of the M4E1 lower: \"This custom-designed enhanced forging is machined from 7075-T6 Aluminum and compatible with all mil-spec AR15 parts\" (its page). The trigger's hole is the Army drawing's: a trigger chosen in its own slot turns here, and the model's hole is cut here."}]},"trigger_pin_y":{"label":"Trigger pin hole centre, Y","kind":"length","measurements":[{"id":"tdp","value":-0.689,"unit":"in","pm":0.0035,"source":{"type":"derived","expr":"{std.ar15.trigger_pin_y}","via":"harvest"},"note":"Aero, of the M4E1 lower: \"This custom-designed enhanced forging is machined from 7075-T6 Aluminum and compatible with all mil-spec AR15 parts\" (its page). The trigger's hole is the Army drawing's."},{"id":"photo","value":-0.677,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-m4e1-lower.trigger_pin_y}","via":"harvest"},"note":"By reference: the hole's centre as read on Aero's right side photo of the stripped M4E1 in its pin frame, recorded under the complete lower. 0.012 above the drawing's, inside its ±."}],"adopt":{"from":"tdp","reason":"The drawing's: Aero says the forging takes mil-spec parts, the model's hole is cut there, and the photo's reading agrees within its ±."}},"grip_lug_rear_x":{"label":"The grip lug's rear face (under the takedown pin), X","kind":"length","measurements":[{"id":"tdp","value":-0.075,"unit":"in","pm":0.025,"source":{"type":"derived","expr":"{std.ar15.receiver_rear_x} + {std.ar15.grip_lug_front_from_rear_face} - {std.ar15.grip_lug_length}","via":"harvest"},"note":"A mil-spec lower's lug ends 2.300 ahead of the rear face and is 1.25 long. Aero, of the M4E1 lower: \"This custom-designed enhanced forging is machined from 7075-T6 Aluminum and compatible with all mil-spec AR15 parts\" (its page)."},{"id":"outline","value":-0.077,"unit":"in","pm":0.013,"source":{"type":"photo","photo":"references/aero-m4e1-stripped-lower 30b8c6d3edf1 (right side, Aero's studio photo of the stripped M4E1, APAR600001C's gallery, both pin holes open)","scaleRef":"rifle frame from the reviewed holes takedown, pivot = (0, 0), (6.375, 0): 118.9 px/in","method":"the traced outline's two points on the lug's upright rear face below the set screw's stub, (-0.079, -1.291) and (-0.075, -1.371) (tools/trace.py); ± is a pixel and a half","via":"harvest"},"note":"The lug's rear face where it shows: above it, from Y -1.08 to -1.24, the silhouette stands 0.04 to 0.05 further back, which is the end of the upper tension set screw in the lug's rear (Aero ships it in the receiver; its bottom photo has it at the lug's rear end), not the lug."}],"adopt":{"from":"tdp","reason":"The drawing's, which a grip's slot is made to; the outline has the face 0.002 from it."}},"grip_lug_flat_y":{"label":"The grip lug's bottom flat (where its sloped face ends, behind the trigger guard's root), Y","kind":"length","measurements":[{"id":"tdp","value":-1.9995,"unit":"in","pm":0.0215,"source":{"type":"derived","expr":"{std.ar15.deck_y} - {std.ar15.grip_seat_below_deck} - {std.ar15.grip_lug_depth}","via":"harvest"},"note":"A mil-spec lower: the flat is .93 below the seat."},{"id":"outline","value":-1.983,"unit":"in","pm":0.013,"source":{"type":"photo","photo":"references/aero-m4e1-stripped-lower 30b8c6d3edf1 (right side, Aero's studio photo of the stripped M4E1, APAR600001C's gallery, both pin holes open)","scaleRef":"rifle frame from the reviewed holes takedown, pivot = (0, 0), (6.375, 0): 118.9 px/in","method":"the traced outline's two points on the flat at the sloped face's foot, (0.991, -1.987) and (1.143, -1.979): their mean (tools/trace.py); ± is a pixel and a half","via":"harvest"},"note":"The flat, 0.017 above the drawing's: inside the two ±."}],"adopt":{"from":"tdp","reason":"The drawing's; the outline has the flat 0.017 above it, inside its ±."}},"grip_lug_face_angle":{"label":"The grip lug's sloped face, from the vertical","kind":"angle","measurements":[{"id":"tdp","value":60,"unit":"deg","pm":2,"source":{"type":"derived","expr":"{std.ar15.grip_lug_face_angle}","via":"harvest"},"note":"A mil-spec lower: the lug is the drawing's (60° ±2°)."},{"id":"outline","value":60,"unit":"deg","pm":1,"source":{"type":"photo","photo":"references/aero-m4e1-stripped-lower 30b8c6d3edf1 (right side, Aero's studio photo of the stripped M4E1, APAR600001C's gallery, both pin holes open)","scaleRef":"rifle frame from the reviewed holes takedown, pivot = (0, 0), (6.375, 0): 118.9 px/in","method":"the traced outline's one straight stretch along the lug's sloped face, from (-0.075, -1.371) to (0.991, -1.987): its lean from the vertical over 1.23 in (tools/trace.py); ± is a pixel at each end","via":"harvest"},"note":"The sloped face: on the drawing's angle, and on its line within 0.004 in at both ends (1.228 from the pin)."}],"adopt":{"from":"tdp","reason":"The drawing's; the outline's stretch is on it."}},"guard_root_rear_x":{"label":"The integral trigger guard's root, its rear face (where the grip's lug ends: a mil-spec lower's ears' rear face), X","kind":"length","measurements":[{"id":"tdp","value":1.175,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{std.ar15.receiver_rear_x} + {std.ar15.grip_lug_front_from_rear_face}","via":"harvest"},"note":"A mil-spec lower: the lug ends at the guard's ears, 2.300 ahead of the rear face: where a grip's nose comes to."},{"id":"outline","value":1.155,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-m4e1-stripped-lower 30b8c6d3edf1 (right side, Aero's studio photo of the stripped M4E1, APAR600001C's gallery, both pin holes open)","scaleRef":"rifle frame from the reviewed holes takedown, pivot = (0, 0), (6.375, 0): 118.9 px/in","method":"the traced outline's upright edge below the lug's flat, from (1.143, -1.979) to (1.167, -2.324): its middle (tools/trace.py); ± covers its lean and a pixel","via":"harvest"},"note":"The rear face of the block the integral guard's bar springs from: it leans 0.024 forward going down, and its middle is 0.02 behind the drawing's ears."}],"adopt":{"from":"tdp","reason":"The drawing's, which a grip's nose is made to; the outline's edge is within its ± of it."}},"rear_underside_arc_r":{"label":"The rear underside (behind the grip's lug, under the tower), the radius of its arc on the centre plane","kind":"length","measurements":[{"id":"model","value":0.75,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{std.ar15.rear_underside_arc_r}","via":"harvest"},"note":"The reference CAD model's arc on a mil-spec forging, about the model's centre (std.ar15.rear_underside_arc_center_x, _below_seat)."},{"id":"outline","value":0.764,"unit":"in","pm":0.013,"source":{"type":"photo","photo":"references/aero-m4e1-stripped-lower 30b8c6d3edf1 (right side, Aero's studio photo of the stripped M4E1, APAR600001C's gallery, both pin holes open)","scaleRef":"rifle frame from the reviewed holes takedown, pivot = (0, 0), (6.375, 0): 118.9 px/in","method":"the traced outline's five points along the underside from X -1.116 to -0.285 (tools/trace.py), each one's distance from the reference model's centre (-1.0238, -1.2623): 0.766, 0.762, 0.763, 0.764, 0.766; their mean; ± is a pixel and a half","via":"harvest"},"note":"Aero's forging has the standard forging's sweep under the tower: 0.012 to 0.016 outside the reference model's arc all along, and so 0.05 clear of the fullest forging on file, which a grip's saddle is cut to (std.ar15.rear_underside_arc_r_fullest)."}],"adopt":{"from":"model","reason":"The reference model's; this receiver's own silhouette runs 0.014 outside it, inside the two ±. The model draws the outline's own line."},"note":"The check that a grip made for a mil-spec lower clears this forging's rear underside: in a square side view the silhouette's lower edge there is the centre plane's line."},"rear_end_x":{"label":"The receiver's rear face (the buffer tower's, where an end plate bears), X","kind":"length","measurements":[{"id":"tdp","value":-1.125,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.ar15.receiver_rear_x}","via":"harvest"},"note":"Aero, of the M4E1 lower: \"This custom-designed enhanced forging is machined from 7075-T6 Aluminum and compatible with all mil-spec AR15 parts\" (its page). The face an end plate bears on is the Army drawing's, 7.503 -.006 behind the pivot pin."},{"id":"photo","value":-1.14,"unit":"in","pm":0.013,"source":{"type":"derived","expr":"{aero-m4e1-lower.rear_face_x}","via":"harvest"},"note":"By reference: the rear face below the ring as Aero's right side photo reads it in its pin frame (the left photo -1.118: the complete lower's entry). 0.015 behind the drawing's: the two ± touch. The ring's near rim, a quarter inch nearer the lens than the pins the photo is scaled by, reads further back still (rear_behind_pin)."}],"adopt":{"from":"tdp","reason":"The drawing's: the end plate, the castle nut and the receiver extension are placed by the standard, and the model's rear face is cut there so the plate bears on it. The photo's reading is 0.015 behind it."}},"guard_width":{"label":"The integral trigger guard across (its post behind the trigger and its bar under it), Z","kind":"length","measurements":[{"id":"bottom","value":0.59,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-m4e1-stripped-lower ab9b1c2f8e07 (bottom view, Aero's studio photo of the stripped M4E1 in FDE Cerakote, APAR600002C: the rear at the top)","scaleRef":"the magazine well seen through from below in the same view: its box is 94 to 95 px across (rows 600 to 628) for the drawing's .898 at the deck, 105.2 px/in, and the receiver's silhouette, which is its body at the seat's level, 93 to 94 px for the drawing's .880, 106.8 px/in: so the lens is some 87 in from the deck and the scale at the bar's lower face, 2.6 in nearer, is 108.4 px/in (the grip lug's flat reads 39 px there: .375 less its edge breaks at 108)","method":"the bar's lower face is the lighter flat between two creases, found as the two largest steps of the mean luminance across rows 352 to 386 (behind its first slot) and rows 455 to 470 (between its two slots): 64 px and 63 px (.cache/b7-m4e1/bar.py), 0.586 in at 108.4 px/in. ± covers a pixel at each crease and the scale's 1.5%","via":"harvest"},"note":"The flat's width. Either side of it, out to the silhouette, the view has a darker band 13 to 14 px wide: taken as the body's underside seen past a narrower guard (the side photos' lip), not as chamfers on a bar of the body's width, which the side photos would show as a band most of the bar's height and don't."}],"note":"Below the grip seat's level this receiver is narrower than its body from the grip's lug forward to the magazine well, as a mil-spec lower is at its trigger guard's ears (the reference CAD model's 0.659 there: std.ar15.trigger_guard_ears_width). In the side photos the body's lower edge stands over the guard as a lip along the seat's level, and the guard's face is one flat with a thin chamfer on its inner edge. One reading, from the one view from below on file: provisional."},"guard_slot_width":{"label":"The two slots through the integral guard's bar, across (Z)","kind":"length","measurements":[{"id":"bottom","value":0.335,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-m4e1-stripped-lower ab9b1c2f8e07 (bottom view, Aero's studio photo of the stripped M4E1 in FDE Cerakote, APAR600002C: the rear at the top)","scaleRef":"the magazine well seen through from below in the same view: its box is 94 to 95 px across (rows 600 to 628) for the drawing's .898 at the deck, 105.2 px/in, and the receiver's silhouette, which is its body at the seat's level, 93 to 94 px for the drawing's .880, 106.8 px/in: so the lens is some 87 in from the deck and the scale at the bar's lower face, 2.6 in nearer, is 108.4 px/in (the grip lug's flat reads 39 px there: .375 less its edge breaks at 108)","method":"each slot's two edges on the bar's lower face, across: the rear slot's dark rims at columns 479.5 and 515 either side of the white (rows 405 to 435), the front slot's steps at 477.5 and 514 (rows 485 to 500): 35.5 and 36.5 px (.cache/b7-m4e1/slot1.py); their mean at 108.4 px/in","via":"harvest"}}],"note":"The bar under the trigger has two oblong slots through it, round-ended, a shorter one behind a longer (Dirty Bird's photo from below and ahead shows both through; Aero's view from below has white through the rear one, where the trigger's slot is above it, and the receiver's underside through the front one). Read on the one view from below: provisional, each end good to about 0.04 in."},"guard_slot1_rear_x":{"label":"The guard bar's rear slot, its rear end, X","kind":"length","measurements":[{"id":"bottom","value":1.655,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/aero-m4e1-stripped-lower ab9b1c2f8e07 (bottom view, Aero's studio photo of the stripped M4E1 in FDE Cerakote, APAR600002C: the rear at the top)","scaleRef":"along the receiver, on the bar's own plane: the well's rear wall, where the white seen through the spine slot begins down the middle (row 587.5), is 3.472 ahead of the takedown pin by the Army drawing (magwell_front_inner_x less magwell_length), and a row is 1/107.3 in there (108.4 less the view's lean of about 8 degrees along the receiver). Checked at the other end: the bar's rear edge at the guard's root, 1.175 by the drawing, should then be at row 341, and the view has it between rows 338 and 346","method":"the step from the bar to the white down the middle, row 392.5 (.cache/b7-m4e1/slots.py); ± covers the scale along the receiver, the bar's own rise and fall under that lean (0.03) and a pixel","via":"harvest"}}]},"guard_slot1_front_x":{"label":"The guard bar's rear slot, its front end, X","kind":"length","measurements":[{"id":"bottom","value":2.279,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/aero-m4e1-stripped-lower ab9b1c2f8e07 (bottom view, Aero's studio photo of the stripped M4E1 in FDE Cerakote, APAR600002C: the rear at the top)","scaleRef":"along the receiver, on the bar's own plane: the well's rear wall, where the white seen through the spine slot begins down the middle (row 587.5), is 3.472 ahead of the takedown pin by the Army drawing (magwell_front_inner_x less magwell_length), and a row is 1/107.3 in there (108.4 less the view's lean of about 8 degrees along the receiver). Checked at the other end: the bar's rear edge at the guard's root, 1.175 by the drawing, should then be at row 341, and the view has it between rows 338 and 346","method":"the step back up to the bar's flat down the middle, row 459.5 (the white ends at row 447.5: beyond it the slot shows the receiver's underside, dark) (.cache/b7-m4e1/slots.py); ± covers the scale along the receiver, the bar's own rise and fall under that lean (0.03) and a pixel","via":"harvest"}}]},"guard_slot2_rear_x":{"label":"The guard bar's front slot, its rear end, X","kind":"length","measurements":[{"id":"bottom","value":2.433,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/aero-m4e1-stripped-lower ab9b1c2f8e07 (bottom view, Aero's studio photo of the stripped M4E1 in FDE Cerakote, APAR600002C: the rear at the top)","scaleRef":"along the receiver, on the bar's own plane: the well's rear wall, where the white seen through the spine slot begins down the middle (row 587.5), is 3.472 ahead of the takedown pin by the Army drawing (magwell_front_inner_x less magwell_length), and a row is 1/107.3 in there (108.4 less the view's lean of about 8 degrees along the receiver). Checked at the other end: the bar's rear edge at the guard's root, 1.175 by the drawing, should then be at row 341, and the view has it between rows 338 and 346","method":"the step down from the bar's flat down the middle, row 476 (.cache/b7-m4e1/slots.py); ± covers the scale along the receiver, the bar's own rise and fall under that lean (0.03) and a pixel","via":"harvest"}}]},"guard_slot2_front_x":{"label":"The guard bar's front slot, its front end, X","kind":"length","measurements":[{"id":"bottom","value":3.258,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/aero-m4e1-stripped-lower ab9b1c2f8e07 (bottom view, Aero's studio photo of the stripped M4E1 in FDE Cerakote, APAR600002C: the rear at the top)","scaleRef":"along the receiver, on the bar's own plane: the well's rear wall, where the white seen through the spine slot begins down the middle (row 587.5), is 3.472 ahead of the takedown pin by the Army drawing (magwell_front_inner_x less magwell_length), and a row is 1/107.3 in there (108.4 less the view's lean of about 8 degrees along the receiver). Checked at the other end: the bar's rear edge at the guard's root, 1.175 by the drawing, should then be at row 341, and the view has it between rows 338 and 346","method":"where the slot's lit front wall ends at the bar's flat down the middle, row 564.5 (.cache/b7-m4e1/slots.py); ± covers the scale along the receiver, the bar's own rise and fall under that lean (0.03) and a pixel","via":"harvest"}}]},"catch_block_front_x":{"label":"The raised block round the magazine catch on the right side (the 'panel'), where its face ends at the front, X","kind":"length","measurements":[{"id":"aero","value":3.64,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-m4e1-stripped-lower 30b8c6d3edf1 (right side, Aero's studio photo of the stripped M4E1, APAR600001C's gallery, both pin holes open)","scaleRef":"rifle frame from the reviewed holes takedown (179.5, 230.5), pivot (937.5, 228.5) = (0, 0), (6.375, 0): 118.9 px/in","method":"the mean luminance along the row 0.15 in below the pin line (above the catch's pocket), .cache/b7-m4e1/fence.py: the block's face is one tone (54 to 59) from X 3.03 to 3.62, then a lit band (67 to 78) from 3.64 to 3.80, then the face's tone again (53 to 58) from 3.83 on. The face ends where the band begins; the band's largest step is at 3.66. Along the row 0.97 below the pin line the block's lit lower chamfer ends at 3.65. ± is two pixels","via":"harvest"}},{"id":"sportsmans","value":3.69,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/aero-m4e1-stripped-lower fa279a70cd8b (right side, Sportsman's Warehouse's photo of the stripped M4E1, 1200 px, both pin holes open)","scaleRef":"rifle frame from the two pin holes' see-through (their bright centroids: (204.4, 496.9) and (1127.5, 495.2)) = (0, 0), (6.375, 0): 144.8 px/in; the see-through is not the rim, so ± is wider","method":"the same row in the larger picture: the face's tone to 3.66, the lit band from 3.69 to 3.87 (its largest step at 3.71), the face's tone from 3.91 on","via":"harvest"}}],"adopt":{"from":"aero","reason":"The photo whose frame is the reviewed rims of the pin holes; the larger picture, framed by its holes' see-through, reads the same edge 0.05 ahead, inside the two ±."},"note":"On the right side the forging stands out round the magazine catch's button as a block with chamfered edges, and ahead of it the magazine well's wall (the face the large A is cut in) is lower: in both right side photos the block's flat face ends in a lit chamfer and the same grey as the face comes back ahead of it. Its face is panel_right_out (0.664 from the centre, read from below under the complete lower); the wall ahead of it is wall_right_below_panel (0.56, read on the front view below the block, where nothing hides it), a hundredth outside a mil-spec well's wall. The complete lower's receiver is drawn with the block's face carried on to the pivot lug: said in this part's report."},"catch_block_front_ramp":{"label":"The catch block's front chamfer, its length along X (from the face's end down to the well's wall)","kind":"length","measurements":[{"id":"aero","value":0.16,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/aero-m4e1-stripped-lower 30b8c6d3edf1 (right side, Aero's studio photo of the stripped M4E1, APAR600001C's gallery, both pin holes open)","scaleRef":"rifle frame from the reviewed holes takedown (179.5, 230.5), pivot (937.5, 228.5) = (0, 0), (6.375, 0): 118.9 px/in","method":"the lit band's length along the same row, from 3.64 to 3.80 (.cache/b7-m4e1/fence.py); ± is two pixels at each end","via":"harvest"},"note":"With the block 0.104 proud of the wall (panel_right_out less wall_right_below_panel) a chamfer this long leans 33 degrees: as long as the block's rear ramp (panel_right_ramp, 0.17)."},{"id":"sportsmans","value":0.18,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/aero-m4e1-stripped-lower fa279a70cd8b (right side, Sportsman's Warehouse's photo of the stripped M4E1, 1200 px, both pin holes open)","scaleRef":"rifle frame from the two pin holes' see-through (their bright centroids: (204.4, 496.9) and (1127.5, 495.2)) = (0, 0), (6.375, 0): 144.8 px/in; the see-through is not the rim, so ± is wider","method":"the lit band's length along the same row in the larger picture, from 3.69 to 3.87","via":"harvest"}}],"adopt":{"from":"aero","reason":"As catch_block_front_x; the two agree within a pixel."}},"height":{"label":"Overall height: the tower ring's top to the lowest point (the end views are scaled by it)","kind":"length","measurements":[{"id":"complete","value":4.079,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{aero-m4e1-lower.height}","via":"harvest"},"note":"By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method). What this part's end views are scaled by."}]},"tower_od":{"label":"The buffer tower's ring, across (the end view; the standard's is 1.392)","kind":"length","measurements":[{"id":"complete","value":1.351,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{aero-m4e1-lower.tower_od}","via":"harvest"},"note":"By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method). The ring across, on Aero's rear view (the standard's round ring is 1.392: Aero's has flats on its sides); the bottom view is scaled by it. IN CONFLICT THERE, and so here: its readings are rear 1.351, rear_fde 1.275; the one adopted there (rear) is the figure taken."}]},"rear_behind_pin":{"label":"Rear of the buffer-tower ring behind the takedown pin","kind":"length","measurements":[{"id":"complete","value":1.155,"unit":"in","pm":0.013,"source":{"type":"derived","expr":"{aero-m4e1-lower.rear_behind_pin}","via":"harvest"},"note":"By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method). The outline's rearmost point: the ring's near rim. The rear face itself is rear_end_x."}]},"front_ahead_of_pin":{"label":"Front of the pivot-pin lug ahead of the takedown pin","kind":"length","measurements":[{"id":"complete","value":6.547,"unit":"in","pm":0.022,"source":{"type":"derived","expr":"{aero-m4e1-lower.front_ahead_of_pin}","via":"harvest"},"note":"By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method). IN CONFLICT THERE, and so here: its readings are right 6.547, left 6.645; the one adopted there (right) is the figure taken."}]},"tower_top_above_pin":{"label":"Top of the buffer-tower ring above the pin line","kind":"length","measurements":[{"id":"complete","value":1.554,"unit":"in","pm":0.013,"source":{"type":"derived","expr":"{aero-m4e1-lower.tower_top_above_pin}","via":"harvest"},"note":"By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method). The end views' offset."}]},"deck_above_pin":{"label":"Receiver top deck above the pin line","kind":"length","measurements":[{"id":"complete","value":0.247,"unit":"in","pm":0.013,"source":{"type":"derived","expr":"{aero-m4e1-lower.deck_above_pin}","via":"harvest"},"note":"By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method). The outline's own top edge. The model's deck is the Army drawing's plane (std.ar15.deck_y, .2485), which this is a reading of."}]},"bottom_below_pin":{"label":"Lowest point below the pin line (the integral guard or the magwell front)","kind":"length","measurements":[{"id":"complete","value":2.508,"unit":"in","pm":0.014,"source":{"type":"derived","expr":"{aero-m4e1-lower.bottom_below_pin}","via":"harvest"},"note":"By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method). The integral trigger guard's bow."}]},"magwell_front_x":{"label":"Magwell front face, X","kind":"length","measurements":[{"id":"complete","value":6.156,"unit":"in","pm":0.021,"source":{"type":"derived","expr":"{aero-m4e1-lower.magwell_front_x}","via":"harvest"},"note":"By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method). IN CONFLICT THERE, and so here: its readings are right 6.156, left 6.268; the one adopted there (right) is the figure taken."}]},"rear_face_x":{"label":"Receiver rear face below the tower ring, X","kind":"length","measurements":[{"id":"complete","value":-1.14,"unit":"in","pm":0.013,"source":{"type":"derived","expr":"{aero-m4e1-lower.rear_face_x}","via":"harvest"},"note":"By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method). The bottom view's offset."}]},"rear_body_width":{"label":"The receiver's rear below the tower ring, across (Z)","kind":"length","measurements":[{"id":"complete","value":1.04,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{aero-m4e1-lower.rear_body_width}","via":"harvest"},"note":"By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method). The rear view's outline at those heights (the bosses and the right panel, 3 to 4.5 in ahead): not the rear end's own width."}]},"panel_right_out":{"label":"The right side panel's face, from the centre plane","kind":"length","measurements":[{"id":"complete","value":0.664,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-m4e1-lower.panel_right_out}","via":"harvest"},"note":"By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method)."}]},"panel_right_rear_x":{"label":"The right side panel's face, where it begins (its ramp's foot 0.17 behind)","kind":"length","measurements":[{"id":"complete","value":3.09,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{aero-m4e1-lower.panel_right_rear_x}","via":"harvest"},"note":"By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method)."}]},"panel_right_ramp":{"label":"The right side panel's ramp up from the body, its length along x","kind":"length","measurements":[{"id":"complete","value":0.17,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{aero-m4e1-lower.panel_right_ramp}","via":"harvest"},"note":"By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method)."}]},"panel_right_bottom_y":{"label":"The right side panel's lower edge, Y (below it the well's wall steps in)","kind":"length","measurements":[{"id":"complete","value":-1.03,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{aero-m4e1-lower.panel_right_bottom_y}","via":"harvest"},"note":"By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method)."}]},"wall_right_below_panel":{"label":"The well's right wall below the panel, from the centre plane","kind":"length","measurements":[{"id":"complete","value":0.56,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{aero-m4e1-lower.wall_right_below_panel}","via":"harvest"},"note":"By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method)."}]},"panel_left_out":{"label":"The left side's face over the magazine well, from the centre plane","kind":"length","measurements":[{"id":"complete","value":0.603,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{aero-m4e1-lower.panel_left_out}","via":"harvest"},"note":"By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method)."}]},"panel_left_rear_x":{"label":"The left side's face over the well, where it begins (its ramp's foot 0.08 behind)","kind":"length","measurements":[{"id":"complete","value":3.03,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{aero-m4e1-lower.panel_left_rear_x}","via":"harvest"},"note":"By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method)."}]},"panel_left_ramp":{"label":"The left face's ramp up from the body, its length along x","kind":"length","measurements":[{"id":"complete","value":0.08,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{aero-m4e1-lower.panel_left_ramp}","via":"harvest"},"note":"By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method)."}]},"catch_pad_out":{"label":"The pad round the magazine catch's slot (left), its face from the centre plane","kind":"length","measurements":[{"id":"complete","value":0.666,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-m4e1-lower.catch_pad_out}","via":"harvest"},"note":"By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method)."}]},"catch_pad_top_y":{"label":"The catch pad's upper edge, Y","kind":"length","measurements":[{"id":"complete","value":-0.3,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{aero-m4e1-lower.catch_pad_top_y}","via":"harvest"},"note":"By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method)."}]},"catch_pad_bottom_y":{"label":"The catch pad's lower edge, Y","kind":"length","measurements":[{"id":"complete","value":-0.78,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{aero-m4e1-lower.catch_pad_bottom_y}","via":"harvest"},"note":"By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method)."}]},"catch_pad_front_x":{"label":"The catch pad's rounded front end, X","kind":"length","measurements":[{"id":"complete","value":4.56,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{aero-m4e1-lower.catch_pad_front_x}","via":"harvest"},"note":"By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method)."}]},"catch_pad_rear_x":{"label":"The catch pad's rear end, X","kind":"length","measurements":[{"id":"complete","value":3.048,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{aero-m4e1-lower.catch_pad_rear_x}","via":"harvest"},"note":"By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method)."}]},"bolt_catch_boss_out":{"label":"Aero's bolt catch bosses, their face from the centre plane (left)","kind":"length","measurements":[{"id":"complete","value":0.708,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-m4e1-lower.bolt_catch_boss_out}","via":"harvest"},"note":"By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method)."}]},"bolt_catch_boss_rear_x":{"label":"Aero's rear bolt catch boss, its rear end, X","kind":"length","measurements":[{"id":"complete","value":3.01,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{aero-m4e1-lower.bolt_catch_boss_rear_x}","via":"harvest"},"note":"By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method)."}]},"bolt_catch_boss_front_x":{"label":"Aero's front bolt catch boss, its front end, X","kind":"length","measurements":[{"id":"complete","value":3.52,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{aero-m4e1-lower.bolt_catch_boss_front_x}","via":"harvest"},"note":"By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method)."}]},"bolt_catch_boss_bottom_y":{"label":"Aero's bolt catch bosses, their lower ends, Y (they rise to the deck)","kind":"length","measurements":[{"id":"complete","value":-0.02,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{aero-m4e1-lower.bolt_catch_boss_bottom_y}","via":"harvest"},"note":"By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method)."}]},"front_view_lug_slot":{"label":"The front lug's slot as the front view's height scale reads it","kind":"length","measurements":[{"id":"complete","value":0.549,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{aero-m4e1-lower.front_view_lug_slot}","via":"harvest"},"note":"By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method)."}]},"ear_right_out":{"label":"The pivot lug's right ear, its outer face from the centre plane (the slot's middle)","kind":"length","measurements":[{"id":"complete","value":0.519,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{aero-m4e1-lower.ear_right_out}","via":"harvest"},"note":"By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method)."}]},"ear_left_out":{"label":"The pivot lug's left ear, its outer face from the centre plane (the slot's middle)","kind":"length","measurements":[{"id":"complete","value":0.542,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{aero-m4e1-lower.ear_left_out}","via":"harvest"},"note":"By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method)."}]},"ears_width":{"label":"The pivot lug across its two ears","kind":"length","measurements":[{"id":"complete","value":1.061,"unit":"in","pm":0.017,"source":{"type":"derived","expr":"{aero-m4e1-lower.ears_width}","via":"harvest"},"note":"By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method)."}]},"ear_right_rear_x":{"label":"The right ear's outer face, where it begins: the right panel's front end, X","kind":"length","measurements":[{"id":"complete","value":6.18,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-m4e1-lower.ear_right_rear_x}","via":"harvest"},"note":"By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method)."}]},"ear_left_rear_x":{"label":"The left ear's outer face, where it begins: the foot of the ramp up to the left side's face, X (at the pin's height)","kind":"length","measurements":[{"id":"complete","value":6.15,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-m4e1-lower.ear_left_rear_x}","via":"harvest"},"note":"By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method)."}]},"ear_left_ramp":{"label":"The ramp from the left ear's face up to the left side's face, its length along X","kind":"length","measurements":[{"id":"complete","value":0.06,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{aero-m4e1-lower.ear_left_ramp}","via":"harvest"},"note":"By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method)."}]}}},{"subject":"aero-m4e1-threaded-upper","title":"Aero Precision M4E1 Threaded stripped upper receiver (APAR700201C)","dimensions":{"weight":{"label":"Weight (the stripped receiver: no port door, forward assist or barrel)","kind":"mass","measurements":[{"id":"aero","value":6.9,"unit":"oz","pm":0.05,"stated":"Weight(s) 6.9 oz","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, M4E1 Threaded Stripped Upper Receiver - Anodized Black (APAR700201C), Specifications","url":"https://www.aeroprecisionusa.com/m4e1-threaded-stripped-upper-receiver-anodized-black","retrieved":"2026-10-02","via":"harvest"}}]},"weight_assembled":{"label":"Weight, assembled (its port door and forward assist installed; no barrel)","kind":"mass","measurements":[{"id":"aero","value":8.65,"unit":"oz","pm":0.005,"stated":"Weight(s) 8.65 oz","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, M4E1 Threaded Assembled Upper Receiver - Anodized Black (APAR700201AC), Specifications","url":"https://www.aeroprecisionusa.com/m4e1-threaded-assembled-upper-receiver-black","retrieved":"2026-10-03","via":"harvest"},"note":"Its page: \"Includes: M4E1 Threaded Upper Receiver in Anodized Black / Port Door and Forward Assist installed\". The stripped one is 6.9 oz."}]},"bore_axis_above_pin":{"label":"Bore axis above the takedown pin centre","kind":"length","measurements":[{"id":"standard","value":0.8775,"unit":"in","pm":0.0015,"source":{"type":"derived","expr":"{std.ar15.bore_axis_y}","via":"harvest"},"note":"The standard's: Aero's page says it is \"precision machined to work with all mil-spec AR15 parts\". Not measured on this upper."}]},"rail_top_above_pin":{"label":"The top rail's surface above the pin line","kind":"length","measurements":[{"id":"left","value":2.09,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 05049cf3016d (Aero: the stripped upper's left side, 1000 px)","scaleRef":"pin frame: its own takedown and pivot lug holes, 6.375 in apart (std.ar15.pin_spacing): 119.2 px/in, tilt 0.05°","method":"the rail's tooth tops (the silhouette's highest in each 0.4 in window, between the lugs) above the line through the two holes: 2.090 (2.080 to 2.092); ± is two pixels","via":"harvest"}},{"id":"right","value":2.085,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 4ffb4e8b026f (Aero: the stripped upper's right side, 1000 px)","scaleRef":"pin frame: its own takedown and pivot lug holes, 6.375 in apart (std.ar15.pin_spacing): 119.0 px/in, tilt −0.11°","method":"as the left photo: 2.085 (2.082 to 2.090)","via":"harvest"}}],"adopt":{"from":"left","reason":"The discovery report's nearer-to-side-on photo; the other side reads the same within half a pixel."},"note":"Read on Aero's own two photos, each in the frame of its own lug holes. The views are level: in the same frames the underside between the lugs reads 0.252 and 0.250, the lower's deck (std.ar15.deck_y, .250)."},"rail_slot0_x":{"label":"The rearmost rail slot's centre ahead of the takedown pin","kind":"length","measurements":[{"id":"photo","value":1.163,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 4ffb4e8b026f (Aero's gallery: the stripped receiver's right side, straight on, 1000 x 630)","scaleRef":"the two lug holes as the pins (takedown at px 118.9, 430.3; pivot at 877.3, 428.9), std.ar15.pin_spacing apart: 118.96 px/in; the rail's 14 slots fit the standard pitch to 0.1% on it","method":"the top edge's slot floors (x 244 to 878 px, 14 slots): their centres fitted to the standard pitch, rms 0.002 in","via":"harvest"}}]},"rail_slots":{"label":"How many rail slots","kind":"count","measurements":[{"id":"photo","value":14,"unit":"count","source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 4ffb4e8b026f (Aero's gallery: the stripped receiver's right side, straight on, 1000 x 630)","scaleRef":"the two lug holes as the pins (takedown at px 118.9, 430.3; pivot at 877.3, 428.9), std.ar15.pin_spacing apart: 118.96 px/in; the rail's 14 slots fit the standard pitch to 0.1% on it","method":"counted along the top edge","via":"harvest"}}],"note":"Behind the first is a solid run of rail over the charging handle's channel (from rail_rear_x)."},"rail_rear_x":{"label":"The top rail's head: where it begins ahead of the tongue, X (the app draws the head from here)","kind":"length","measurements":[{"id":"standard","value":0.4165,"unit":"in","pm":0.006,"source":{"type":"derived","expr":"{std.ar15.rail_tongue_shoulder_x}","via":"user"}}],"note":"Until 2026-10-20 this was the rail's rearmost point (now rail_tongue_rear_x), and the app drew the head at its full width from there, square: the charging handle's T, cut round for a rounded rail end, stood in its corners. Behind this the rail is the standard's tongue (std.ar15.rail_tongue_*), which the receiver's model carries, as the 22RB's does."},"rail_tongue_rear_x":{"label":"The top rail's tongue: its rounded end's rearmost point, X ahead of the takedown pin","kind":"length","measurements":[{"id":"photo","value":-0.562,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 4ffb4e8b026f (Aero's gallery: the stripped receiver's right side, straight on, 1000 x 630)","scaleRef":"the two lug holes as the pins (takedown at px 118.9, 430.3; pivot at 877.3, 428.9), std.ar15.pin_spacing apart: 118.96 px/in; the rail's 14 slots fit the standard pitch to 0.1% on it","method":"where the top edge first reaches the teeth's height, x 52 px","via":"harvest"}}]},"rail_front_x":{"label":"The top rail's front end ahead of the takedown pin","kind":"length","measurements":[{"id":"photo","value":6.583,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 4ffb4e8b026f (Aero's gallery: the stripped receiver's right side, straight on, 1000 x 630)","scaleRef":"the two lug holes as the pins (takedown at px 118.9, 430.3; pivot at 877.3, 428.9), std.ar15.pin_spacing apart: 118.96 px/in; the rail's 14 slots fit the standard pitch to 0.1% on it","method":"the last tooth's front, x 902 px","via":"harvest"}}],"note":"Ahead of it the receiver's front is lower, round the barrel nut's threads."},"receiver_rear_x":{"label":"The receiver's rear face behind the takedown pin (negative)","kind":"length","measurements":[{"id":"standard","value":-0.621,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.ar15.upper_rear_face_x}","via":"harvest"},"note":"The Army's drawing of the upper (8448524): Aero's is made to work with mil-spec parts."},{"id":"left","value":-0.642,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 05049cf3016d (Aero: the stripped upper's left side, 1000 px)","scaleRef":"pin frame: its own takedown and pivot lug holes, 6.375 in apart (std.ar15.pin_spacing): 119.2 px/in","method":"the silhouette's rear end behind the takedown hole's centre; ± is two pixels and what a near edge reads long from a lens a few feet away","via":"harvest"}},{"id":"right","value":-0.645,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 4ffb4e8b026f (Aero: the stripped upper's right side, 1000 px)","scaleRef":"pin frame: its own takedown and pivot lug holes, 6.375 in apart (std.ar15.pin_spacing): 119.0 px/in","method":"as the left photo","via":"harvest"}}],"adopt":{"from":"standard","reason":"The drawing dimensions the face; the two photos read 0.02 in more, as a silhouette's near edge does, and agree with it within their ±."}},"front_face_x":{"label":"The receiver's front face (the end of its barrel-nut thread) ahead of the takedown pin","kind":"length","measurements":[{"id":"standard","value":7.036,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.ar15.upper_front_face_x}","via":"harvest"},"note":"The Army's drawing: .661 ahead of the pivot lug's hole. Aero: \"threaded to accept a standard AR15 barrel nut\"."},{"id":"left","value":7.061,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 05049cf3016d (Aero: the stripped upper's left side, 1000 px)","scaleRef":"pin frame: its own takedown and pivot lug holes, 6.375 in apart (std.ar15.pin_spacing): 119.2 px/in","method":"the silhouette's front end 0.686 ahead of the pivot hole's centre; ± is two pixels and the near edge","via":"harvest"}},{"id":"right","value":7.053,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 4ffb4e8b026f (Aero: the stripped upper's right side, 1000 px)","scaleRef":"pin frame: its own takedown and pivot lug holes, 6.375 in apart (std.ar15.pin_spacing): 119.0 px/in","method":"0.678 ahead of the pivot hole's centre","via":"harvest"}}],"adopt":{"from":"standard","reason":"The drawing dimensions the face; both photos read 0.02 in more, as at the rear, and agree with it within their ±."}},"underside_y":{"label":"The receiver's underside above the pin line","kind":"length","measurements":[{"id":"standard","value":0.2485,"unit":"in","pm":0.0015,"source":{"type":"derived","expr":"{std.ar15.deck_y}","via":"harvest"},"note":"It sits on the lower's deck. The two photos read 0.252 and 0.250 between the lugs. (Written 0.25 ± 0.003 until 2026-10-12, a hundredth and a half off its own expression: the model's underside stood that far off a deck drawn on the standard's plane.)"}]},"width":{"label":"Width of the receiver's body","kind":"length","measurements":[{"id":"tdp","value":1.18,"unit":"in","pm":0.02,"stated":"FORGED DIA 1.18 DIA REF -V-","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 2, PDF page 109, View G-G"},"note":"The round body just behind the threaded nose. The A2's 12576280 sheet 2, Section D-D: (1.19) FORGED Ø."},{"id":"above","value":1.18,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper a2b2dd914c15 (OpticsPlanet's gallery for APAR700201C: the receiver from above, its muzzle end up, 978 x 550)","scaleRef":"the rail's own width in the same photo (std.picatinny.top_width: its lug tops 38.5 px across, 46 px/in at the rail's top) and the barrel-nut thread's (1.25 in by Aero's page: 51 px, 40.8 px/in at the bore's level 1.21 in lower: the lens stood some 10 in above it), what lies between at the scale its depth gives; the part's middle is the rail's (column 472)","method":"the lit sloped face beside the rail ends 7 px outside the rail's edge on the left and 8 on the right, at a depth where an inch is 44.5 px: 0.575 and 0.60 from the middle (.cache/m4e1-upper/top_tones.py)","via":"harvest"},"note":"Clear of the port door's bosses, the forward assist's housing and the deflector, which stand out past it on the right."}],"adopt":{"from":"tdp","reason":"The Army's figure for the forging's round body; this receiver read from above has the same across its widest, within what a 978 px photo carries."},"note":"The Army's upper receiver is made from a forging whose drawing isn't in the package; the machined drawing gives the round body's forged diameter as a reference, and the A2's agrees within .01. Aero's receiver is the mil-spec pattern (its page: \"precision machined to work with all mil-spec AR15 parts\"). Its forward assist's housing and the ejection port's door boss stand out past it on the right."},"charging_handle_above_bore":{"label":"The charging handle's channel above the bore's axis","kind":"length","measurements":[{"id":"photo","value":0.86,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 4ffb4e8b026f (Aero's gallery: the stripped receiver's right side, straight on, 1000 x 630)","scaleRef":"the two lug holes as the pins, std.ar15.pin_spacing apart: 118.96 px/in","method":"the notch in the traced outline's rear end, 1.58 to 1.90 above the pin line: its middle less the bore's 0.8775","via":"harvest"}},{"id":"standard","value":0.8563,"unit":"in","pm":0.007,"source":{"type":"derived","expr":"{std.ar15.charging_handle_axis_y} - {.bore_axis_above_pin}","via":"user"},"note":"Riding on its guide lugs on the channel's tier: std.ar15.charging_handle_axis_y."}],"adopt":{"from":"standard","reason":"A handle rides on its guide lugs on the channel's tier (std.ar15.charging_handle_axis_y, the Army's drawing's); the photo reads the notch's middle, which is the room the handle's block lies in, and agrees within its ±. The receiver had no channel drawn until 2026-10-20."},"note":"Its latch's notch in the receiver's rear face, which the handle's latch hooks into: the handle lies at its height."},"handle_seat_x":{"label":"The charging handle's seat: the front wall of the open notch under the rail's rear end, ahead of the takedown pin","kind":"length","measurements":[{"id":"right","value":0.092,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 4ffb4e8b026f (Aero's gallery: the stripped receiver's right side, straight on, 1000 x 630)","scaleRef":"the two lug holes as the pins, std.ar15.pin_spacing apart: 118.96 px/in","method":"the notch's front wall in the traced outline's rear end (profiles.side): its flat at x 0.092 from y 1.667 to 1.818, between two corners cut back at 45 degrees to x 0.013 and 0.004; ± is two pixels and the wall's near edge, which a lens a few feet away reads up to 0.02 behind the wall itself","via":"harvest"}},{"id":"tdp","value":0.075,"unit":"in","pm":0.015,"source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: side elevation, scaled (the notch has no callout in this view); user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"},"note":"Scaled, not a callout. On the 6600 px scan the two lug holes, fitted as circles, are 1966 px apart (308.4 px/in over std.ar15.pin_spacing) and the notch's front wall (column 2427.5) is 21.5 px ahead of the takedown hole's centre: 0.070. From the rear face's line, 217 px behind the wall, it is 0.083: the drawing dimensions that face at -0.621 and the scan has it at -0.634 by the holes. Between the two; ± covers both. The notch is 0.31 to 0.32 high there, for the handle's .2985 (drawing 8448518), its front corners cut back 0.06."}],"adopt":{"from":"right","reason":"This receiver's own notch, where its model's wall is; the Army's drawing, scaled, reads 0.017 less: within both ±."},"note":"Where a charging handle stops. The notch is cut across the receiver under the rail's rear end and is open to the rear: the handle's block (its T ahead of the wings, as thick as the shaft) lies in it with its shoulder against this wall, and the shaft runs on through the slot ahead of it. Until 2026-10-05 the handle was placed with its shoulder at the rear face, 0.7 in behind this (that day's review of the models: its whole T hung behind the receiver, over the castle nut). Magpul's photo of a handle in a receiver (references/magpul-mbus-3-rear 9248df8685e9) has it so: the T's wing astride the rear face, the notch filled to its front wall."},"body_radius":{"label":"The round body's radius about the bore (the forging's)","kind":"length","measurements":[{"id":"tdp","value":0.59,"unit":"in","pm":0.01,"stated":"FORGED DIA 1.18 DIA REF -V-","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 2 of 2, rev G: View G-G; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p109","via":"user"}},{"id":"model","value":0.6,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/research/aero-upper/step), cut at x 1.8: cylindrical faces r 0.6000 about the bore's axis, x -0.43 to 6.59","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's forged figure; the model's is 0.01 more."}},"bore_d":{"label":"The bore the bolt carrier runs in","kind":"length","measurements":[{"id":"tdp","value":1,"unit":"in","pm":0.005,"stated":"1.000 -P-","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), the bore -P- (as 8448522 dimensions the gas tube from it: std.ar15.gas_tube_above_bore); user-supplied scan","via":"user"}}]},"dovetail_foot_y":{"label":"The rail's dovetail, its foot (where the neck begins), Y above the pin line","kind":"length","measurements":[{"id":"model","value":1.885,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/research/aero-upper/step), cut at x 1.8: the plane under the dovetail at y 1.885, z 0.309-0.333; the 45° face from (0.333, 1.885) to (0.418, 1.969)","via":"user"}},{"id":"photo","value":1.89,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 4ffb4e8b026f (Aero's gallery: the stripped receiver's right side, 1000 x 630)","scaleRef":"its lug holes, std.ar15.pin_spacing apart: 118.96 px/in","method":"the horizontal edge under the rail, px row 205","via":"harvest"}}],"adopt":{"from":"model","reason":"The model's face; Aero's photo agrees within its ±."}},"dovetail_foot_half_width":{"label":"The rail's dovetail at its foot, half its width","kind":"length","measurements":[{"id":"model","value":0.333,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/research/aero-upper/step), cut at x 1.8: the 45° face's lower end, z 0.333","via":"user"}},{"id":"std","value":0.323,"unit":"in","pm":0.013,"source":{"type":"derived","expr":"{std.picatinny.bevel_width} / 2 + {std.picatinny.lower_gauge_below_top} - ({.rail_top_above_pin} - {.dovetail_foot_y})","via":"harvest"},"note":"The standard's lower face carried on at its 45 degrees from the lower gauge line (.748 across, .154 below the rail's top) to the height the reference model has the foot at: the face every other rail on file has (the teeth the app draws on this body, a handguard's own rail) and every clamp's channel is cut to. ± is the gauge line's .010 and the model's .003."}],"adopt":{"from":"std","reason":"The standard's, since 2026-10-12: a rail's head is MIL-STD-1913's, and the clamps' channels are cut to it (pipeline/blender/lib.py rail_seat). The reference model draws the same face a hundredth further out, at the standard's stated .164 where the ledger has the middle of .164 -.020 (std.picatinny.lower_gauge_below_top): inside the standard's band, and on a body drawn so every clamp stood 0.008 in into the rail along both sides (0.001 cubic inches of an Aimpoint's base). The model isn't authoritative beside the standard (D49); its neck and the foot's height are still its own."}},"rail_neck_half_width":{"label":"The rail's neck below its dovetail, half its width","kind":"length","measurements":[{"id":"model","value":0.309,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/research/aero-upper/step), cut at x 1.8: planar faces z ±0.309 from y 1.700 to 1.885","via":"user"}}]},"rail_neck_bottom_y":{"label":"The rail's neck, where it meets the body below it, Y","kind":"length","measurements":[{"id":"model","value":1.7,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/research/aero-upper/step), cut at x 1.8: the step out from ±0.309 to ±0.319 at y 1.700","via":"user"}},{"id":"sides","value":1.737,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 05049cf3016d and 4ffb4e8b026f (Aero's gallery: the M4E1 Threaded stripped upper's left and right sides, each 1000 x 630)","scaleRef":"the right view's lug holes on the standard pin spacing (std.ar15.pin_spacing: 119.0 px/in); the left view is the same size (its part spans the same 918 px); heights from the rail's top (aero-m4e1-threaded-upper.rail_top_above_pin)","method":"the tone down the body at three columns clear of its bump, its pockets and its port: a bright line 42 px below the rail's top in both views (the rail's side dark above it, the body's dark below), the edge where the body begins under the rail's neck (.cache/m4e1-upper/left_cols.py)","via":"harvest"}}],"adopt":{"from":"sides","reason":"This receiver's own, on Aero's photos of both its sides. The model is a mil-spec forging's, 0.04 lower; the R-ONE handguard's neck, which Aero says this rail blends with, ends 0.377 below the top (1.713)."}},"side_half_width":{"label":"The body's upper sides, below the rail's neck: half the width across them","kind":"length","measurements":[{"id":"model","value":0.319,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/research/aero-upper/step), cut at x 1.8: planar faces z ±0.319 from y 1.440 to 1.700, then a .10 fillet to the round body","via":"user"}},{"id":"above","value":0.42,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper a2b2dd914c15 (OpticsPlanet's gallery for APAR700201C: the receiver from above, its muzzle end up, 978 x 550)","scaleRef":"the rail's own width in the same photo (std.picatinny.top_width: its lug tops 38.5 px across, 46 px/in at the rail's top) and the barrel-nut thread's (1.25 in by Aero's page: 51 px, 40.8 px/in at the bore's level 1.21 in lower: the lens stood some 10 in above it), what lies between at the scale its depth gives; the part's middle is the rail's (column 472)","method":"across four rows through the rail: outside the lug tops' edges (columns 453 and 491) comes at once the lit face that slopes out to the body's widest, 6 to 8 px of it each side, with no ledge between: under the rail's neck the body is as wide as the rail's head, within a pixel (.cache/m4e1-upper/top_tones.py)","via":"harvest"}}],"adopt":{"from":"above","reason":"This receiver's own: the M4E1's sides under the rail stand out level with the rail's head, a slab where the mil-spec forging the model is of has a waist 0.64 across. The two are different receivers; the conflict is that."},"note":"The M4E1's \"billet look\" (Aero's words for the forging): a flat band each side under the rail, then a flat face sloping out to the round body's widest at the bore's level. The mil-spec forging has a narrow waist here and the round body's top."},"side_bottom_y":{"label":"The body's upper sides, their lower edge (where the face that slopes out begins), Y","kind":"length","measurements":[{"id":"model","value":1.44,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/research/aero-upper/step), cut at x 1.8: the flat sides' lower end at y 1.440","via":"user"}},{"id":"sides","value":1.435,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 05049cf3016d and 4ffb4e8b026f (Aero's gallery: the M4E1 Threaded stripped upper's left and right sides, each 1000 x 630)","scaleRef":"the right view's lug holes on the standard pin spacing (std.ar15.pin_spacing: 119.0 px/in); the left view is the same size (its part spans the same 918 px); heights from the rail's top (aero-m4e1-threaded-upper.rail_top_above_pin)","method":"the same columns: two bright lines 78 and 90 px below the rail's top in the left view (0.655 and 0.756 in), the upper band's dark above them and the sloped face's even grey below: the band ends at the upper line, and a break 0.10 tall lies between it and the sloped face (.cache/m4e1-upper/left_cols.py)","via":"harvest"}}],"adopt":{"from":"sides","reason":"This receiver's own; the mil-spec forging's model has its sides end 0.005 higher."}},"shoulder_bottom_y":{"label":"The sloped faces' lower edge, where the body is widest, Y","kind":"length","measurements":[{"id":"sides","value":0.875,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 05049cf3016d and 4ffb4e8b026f (Aero's gallery: the M4E1 Threaded stripped upper's left and right sides, each 1000 x 630)","scaleRef":"the right view's lug holes on the standard pin spacing (std.ar15.pin_spacing: 119.0 px/in); the left view is the same size (its part spans the same 918 px); heights from the rail's top (aero-m4e1-threaded-upper.rail_top_above_pin)","method":"the same columns in the left view: the sloped face's even grey (about 100) gives way to the lower band's dark (about 53) between 141 and 147 px below the rail's top, 1.21 in (.cache/m4e1-upper/left_cols.py)","via":"harvest"}}],"note":"Level with the bore (0.8775): below it the body is taken to be the forging's round one (body_radius), which the lower receiver's deck and the carrier's bore both need; that half's own shape isn't sourced (a view from an end would show it)."},"lug_wall_half_width":{"label":"The walls below the round body down to the underside, half the width","kind":"length","measurements":[{"id":"model","value":0.453,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/research/aero-upper/step), cut at x 1.8: planar faces z ±0.453 from y 0.250 to 0.458 (inside ±0.251)","via":"user"}}]},"port_length":{"label":"The ejection port's length","kind":"length","measurements":[{"id":"tdp","value":3.125,"unit":"in","pm":0.005,"stated":"3.125; .25 R TRUE 2 PLACES; 1.562 ±.010","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: side elevation; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}},{"id":"photo","value":3.111,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 4ffb4e8b026f (Aero's gallery: the stripped receiver's right side, 1000 x 630)","scaleRef":"its lug holes, std.ar15.pin_spacing apart: 118.96 px/in","method":"the dark opening, px 470 to 840","via":"harvest"}},{"id":"model","value":3.097,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/research/aero-upper/step), cut at x 1.8: its r .25 end cylinders' axes at x 3.182 and 5.779, plus their radii","via":"user"}}],"adopt":{"from":"tdp","reason":"The callout; the photo agrees within its ±, the model is 0.028 short."}},"port_front_x":{"label":"The ejection port's front end ahead of the takedown pin","kind":"length","measurements":[{"id":"tdp","value":6.036,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{.front_face_x} - 1.00in","via":"user"},"note":"8448524 sheet 1: \"1.00\" read as from the port's front end to the receiver's front end; a \".042\" is drawn beside it: read the other way the port would end at 5.994, which the photo rules out."},{"id":"photo","value":6.062,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 4ffb4e8b026f (Aero's gallery: the stripped receiver's right side, 1000 x 630)","scaleRef":"its lug holes, std.ar15.pin_spacing apart: 118.96 px/in","method":"the opening's front end, px 840","via":"harvest"}},{"id":"model","value":6.029,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/research/aero-upper/step), cut at x 1.8: the front end cylinder's axis 5.779 + .25 (1.000 behind its 7.029 face)","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing; the photo reads 0.026 more (within its ±)."}},"port_bottom_y":{"label":"The port's lower edge above the pin line, seen from the side (its ends R .25: 0.50 high)","kind":"length","measurements":[{"id":"drawn","value":0.841,"unit":"in","pm":0.01,"source":{"type":"standard","doc":"8448524 sheet 1 side view, scaled (not a callout): its lower straight edge at px row 3640 against the lug holes' row 3900 at the sheet's own 309.3 px/in (the lug holes 6.375 apart); R .25 TRUE ends","via":"user"}},{"id":"photo","value":0.834,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 4ffb4e8b026f (Aero's gallery: the stripped receiver's right side, 1000 x 630)","scaleRef":"its lug holes, std.ar15.pin_spacing apart: 118.96 px/in","method":"the dark opening's bottom, px row 330; its top reads 1.399, 0.06 above the drawing's: the upper wall's inside, seen from slightly above, is in the dark","via":"harvest"}},{"id":"model","value":0.816,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/research/aero-upper/step), cut at x 1.8: the slot's lower wall at its seat, y 0.816; the upper 1.317","via":"user"}}],"adopt":{"from":"drawn","reason":"The drawing's outline at its own scale; the photo agrees within its ±."}},"port_end_r":{"label":"The port's ends' radius (half its height from the side)","kind":"length","measurements":[{"id":"tdp","value":0.25,"unit":"in","pm":0.005,"stated":".25 R TRUE 2 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: side elevation; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}}]},"fa_axis_angle":{"label":"The forward assist's axis, turned inward toward the front in plan","kind":"angle","measurements":[{"id":"tdp","value":20,"unit":"deg","pm":1,"stated":"20°","source":{"type":"standard","doc":"8448524 sheet 1, the plan view's forward assist section (zone D-7): CL HOLE at 20°, .509 DIA ±.003, .315 DIA ±.001, 1.0285 ±.0050","via":"user"}},{"id":"model","value":22.5,"unit":"deg","pm":0.2,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/research/aero-upper/step), cut at x 1.8: the bore's axis direction (0.924, 0, -0.383)","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing wins (D49); the model's 22.5 beside it."}},"fa_bore_d":{"label":"The forward assist's bore","kind":"length","measurements":[{"id":"tdp","value":0.509,"unit":"in","pm":0.003,"stated":".509 DIA ±.003","source":{"type":"standard","doc":"8448524 sheet 1, the plan view's forward assist section","via":"user"}}]},"fa_bore_depth":{"label":"The forward assist's bore, how deep its .509 runs from the housing's rear face","kind":"length","measurements":[{"id":"tdp","value":0.65,"unit":"in","pm":0.01,"stated":".65","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: the plan view's forward assist section; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}}],"note":"Read as the .509 bore's depth along its axis; ahead of it the hole is the .315 (as expo-arms-stripped-upper.fa_bore_depth reads the same view). Until 2026-10-05 the model bored the .509 for 2.0 in, and it came out through the wall under the housing (that day's review of the models: a slit 0.4 by 0.05 in)."},"fa_inner_bore_d":{"label":"The forward assist's inner bore, ahead of the .509","kind":"length","measurements":[{"id":"tdp","value":0.315,"unit":"in","pm":0.001,"stated":".315 DIA ±.001","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: the plan view's forward assist section; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}}]},"fa_rear_x":{"label":"The forward assist bore's rear opening, X","kind":"length","measurements":[{"id":"model","value":-0.395,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/research/aero-upper/step), cut at x 1.8: the r .25 bore on its axis through (-0.395, 0.879, 1.090)","via":"user"}},{"id":"photo","value":-0.419,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 4ffb4e8b026f (Aero's gallery: the stripped receiver's right side, 1000 x 630)","scaleRef":"its lug holes, std.ar15.pin_spacing apart: 118.96 px/in","method":"the bore's dark ellipse px u 60-78, v 295-355, centre (69, 325)","via":"harvest"}}],"adopt":{"from":"model","reason":"The model places the bore in all three; Aero's photo agrees within its ± in x and y."}},"fa_rear_z":{"label":"The forward assist bore's rear opening, out from the middle (Z)","kind":"length","measurements":[{"id":"model","value":1.09,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/research/aero-upper/step), cut at x 1.8: the bore's axis at its rear opening","via":"user"}}],"note":"The mil-spec forging's: how far the M4E1's own housing stands out isn't sourced (no end or top view of it on file)."},"fa_housing_r":{"label":"The forward assist housing's radius about its axis (the forging's)","kind":"length","measurements":[{"id":"model","value":0.3125,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/research/aero-upper/step), cut at x 1.8: the housing's cylinder r .3125 on the bore's axis, x -0.34 (its rounded rear) to 1.59","via":"user"}}]},"fa_housing_front_x":{"label":"The forward assist housing's front end, X","kind":"length","measurements":[{"id":"model","value":1.59,"unit":"in","pm":0.02,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/research/aero-upper/step), cut at x 1.8: the housing's cylinder ends at x 1.59","via":"user"}},{"id":"side","value":1.9,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 4ffb4e8b026f (Aero's gallery: the M4E1 Threaded stripped upper's right side, straight on, 1000 x 630)","scaleRef":"its lug holes on the standard pin spacing (std.ar15.pin_spacing): 119.0 px/in","method":"the front of the housing's outline as traced (profiles.side.features, forward_assist_housing: its corner at column 345), where the deflector's ridge begins","via":"harvest"}}],"adopt":{"from":"side","reason":"This receiver's own housing, which runs on into its deflector; the model is a mil-spec forging's, whose round housing ends 0.3 in sooner."}},"fa_housing_out_rear":{"label":"The forward assist housing's outer face at the receiver's rear, out from the middle (Z)","kind":"length","measurements":[{"id":"above","value":1.67,"unit":"in","pm":0.1,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper a2b2dd914c15 (OpticsPlanet's gallery for APAR700201C: the receiver from above, its muzzle end up, 978 x 550)","scaleRef":"the rail's own width in the same photo (std.picatinny.top_width: its lug tops 38.5 px across, 46 px/in at the rail's top) and the barrel-nut thread's (1.25 in by Aero's page: 51 px, 40.8 px/in at the bore's level 1.21 in lower: the lens stood some 10 in above it), what lies between at the scale its depth gives; the part's middle is the rail's (column 472)","method":"the part's right edge row by row against the white: a straight line from column 505 at row 345 to 541 at row 441 (0.375 px a row), which at the bore's level is 0.81 in out at x 1.67 and 1.69 out at x -0.68; taken at the receiver's rear face (.cache/m4e1-upper/top_rows.py)","via":"harvest"}}],"note":"The M4E1's housing is a block, flat-faced: from above its outer face is a straight line from here in toward the deflector, 20.5 degrees to the bore's line (the forward assist's own angle, fa_axis_angle), and its rear is cut square to that. The mil-spec forging's is a round boss 0.31 about the forward assist's axis (fa_housing_r), 1.40 out."},"fa_housing_outer_top_y":{"label":"The forward assist housing's outer face, its upper edge (where the face that slopes down from the body meets it), Y","kind":"length","measurements":[{"id":"side","value":1.2,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 4ffb4e8b026f (Aero's gallery: the M4E1 Threaded stripped upper's right side, straight on, 1000 x 630)","scaleRef":"its lug holes on the standard pin spacing (std.ar15.pin_spacing): 119.0 px/in, the pin line at row 430.3","method":"the tone down the housing at six columns from x -0.07 to 1.61: the lit face (110 to 125) ends at a dark line 1.23 above the pins at its rear and 1.17 at its front (.cache/m4e1-upper/housing_cols.py)","via":"harvest"}}],"note":"From the right the housing is three bands: a lit face from its top (1.41) down to here, a mid-toned one, the outer face, and a dark one under it that slopes back in to the body. Flat faces with edges between: a block, where the forging's is a round boss."},"fa_housing_outer_bottom_y":{"label":"The forward assist housing's outer face, its lower edge (where the face that slopes back in to the body begins), Y","kind":"length","measurements":[{"id":"side","value":0.92,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 4ffb4e8b026f (Aero's gallery: the M4E1 Threaded stripped upper's right side, straight on, 1000 x 630)","scaleRef":"its lug holes on the standard pin spacing (std.ar15.pin_spacing): 119.0 px/in, the pin line at row 430.3","method":"the same columns: the mid-toned face (about 80) gives way to the dark one (about 48) 0.95 above the pins at its rear and 0.89 at its front (.cache/m4e1-upper/housing_cols.py)","via":"harvest"}}]},"deflector_out":{"label":"The brass deflector's reach out from the middle (Z)","kind":"length","measurements":[{"id":"model","value":1.25,"unit":"in","pm":0.05,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/research/aero-upper/step), cut at x 1.8: its faces (r 5.0 and r 1.5 tilted cylinders) reach z 1.20-1.30 over x 2.06-2.99, y 0.95-1.70","via":"user"}},{"id":"above","value":1.47,"unit":"in","pm":0.1,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper a2b2dd914c15 (OpticsPlanet's gallery for APAR700201C: the receiver from above, its muzzle end up, 978 x 550)","scaleRef":"the rail's own width in the same photo (std.picatinny.top_width: its lug tops 38.5 px across, 46 px/in at the rail's top) and the barrel-nut thread's (1.25 in by Aero's page: 51 px, 40.8 px/in at the bore's level 1.21 in lower: the lens stood some 10 in above it), what lies between at the scale its depth gives; the part's middle is the rail's (column 472)","method":"the part's right edge row by row: the deflector's point at column 534, row 303, 62 px from the middle at a depth (0.85 in below the rail's top) where an inch is 42.3 px (.cache/m4e1-upper/top_rows.py)","via":"harvest"}}],"adopt":{"from":"above","reason":"This receiver's own, from above; the model is a mil-spec forging's, whose deflector is a smaller boss. They are different receivers."},"note":"From above it is a triangle: a long face from the housing's front out to its point and a short one back in to the port's rear end."},"deflector_point_x":{"label":"The brass deflector's point (where it reaches furthest out), X","kind":"length","measurements":[{"id":"above","value":2.72,"unit":"in","pm":0.15,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper a2b2dd914c15 (OpticsPlanet's gallery for APAR700201C: the receiver from above, its muzzle end up, 978 x 550)","scaleRef":"the rail's own width in the same photo (std.picatinny.top_width: its lug tops 38.5 px across, 46 px/in at the rail's top) and the barrel-nut thread's (1.25 in by Aero's page: 51 px, 40.8 px/in at the bore's level 1.21 in lower: the lens stood some 10 in above it), what lies between at the scale its depth gives; the part's middle is the rail's (column 472); along the receiver, the rail's own ends (aero-m4e1-threaded-upper.rail_rear_x, rail_front_x) about the photo's middle row","method":"the row of the deflector's point, 303, where the rail's middle (x 3.07) is row 288 (.cache/m4e1-upper/top_rows.py)","via":"harvest"},"note":"The side view has the deflector from x 1.88 to 2.95 with its ridge's top at 2.56: the point is nearer its front."}]},"deflector_point_y":{"label":"The brass deflector's point (where it reaches furthest out), Y","kind":"length","measurements":[{"id":"side","value":1.16,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 4ffb4e8b026f (Aero's gallery: the M4E1 Threaded stripped upper's right side, straight on, 1000 x 630)","scaleRef":"its lug holes on the standard pin spacing (std.ar15.pin_spacing): 119.0 px/in, the pin line at row 430.3","method":"the tone down the deflector at x 2.53: its lit face (102 to 135) runs from its top edge (1.65) down to 1.17, a darker one below it; at x 2.78 the lit face is gone (.cache/m4e1-upper/housing_cols.py)","via":"harvest"}}],"note":"Its faces are flat and meet at this point: a large one above and behind it, lit in the side view, a dark one ahead of it and one below."},"cam_boss_x":{"label":"The cam pin's boss on the left side, its middle, X","kind":"length","measurements":[{"id":"left","value":5.14,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 21bd55fd00b4 (Aero's gallery: the M4E1 Threaded stripped upper in FDE Cerakote, APAR700202C, its left side, straight on, 1000 x 630: the same forging in the colour that shows relief)","scaleRef":"its own lug holes on the standard pin spacing (std.ar15.pin_spacing): the takedown hole's centre at (883.8, 424.6) px, the pivot hole's near rim centred 123.5: 119.2 px/in ± 0.3 (the black left view in the same pose, 05049cf3016d: 119.17); the frame checked on the underside (395 px: 0.248 for the drawing's 0.2485), the rail's top (176 px: 2.086 for 2.09) and the front face (45 px: 7.03 for 7.036). The holes are on the centre plane and the wall read is about half an inch nearer the lens: the ± covers it","method":"rows 229 to 243: its upper edge runs 242.5 to 301 px and its ends at their widest 227.3 to 316.2, both centred 271.75; its outer face 249.5 to 290.5 (rows 256 to 279), centred 270: 271.3 px taken, (883.8 - 271.3) / 119.2","via":"harvest"}}],"note":"A raised block over the pocket the cam pin's head turns into. From the side: an upright outer face, a lit face above it sloping back to the band under the rail, and a lit face running down to the band ahead and behind (its two ends, wider than the outer face)."},"cam_boss_face_half_width":{"label":"The cam pin's boss, its upright outer face, half its length","kind":"length","measurements":[{"id":"left","value":0.172,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 21bd55fd00b4 (Aero's gallery: the M4E1 Threaded stripped upper in FDE Cerakote, APAR700202C, its left side, straight on, 1000 x 630: the same forging in the colour that shows relief)","scaleRef":"its own lug holes on the standard pin spacing (std.ar15.pin_spacing): the takedown hole's centre at (883.8, 424.6) px, the pivot hole's near rim centred 123.5: 119.2 px/in ± 0.3 (the black left view in the same pose, 05049cf3016d: 119.17); the frame checked on the underside (395 px: 0.248 for the drawing's 0.2485), the rail's top (176 px: 2.086 for 2.09) and the front face (45 px: 7.03 for 7.036). The holes are on the centre plane and the wall read is about half an inch nearer the lens: the ± covers it","method":"rows 256, 262, 268, 274 and 279: the face's even tone (141 to 147) between 249.5 and 290.5 px at every row, darker flanks outside it: 41 px / 119.2 / 2","via":"harvest"}}]},"cam_boss_face_top_y":{"label":"The cam pin's boss, its outer face's upper edge (and its ends' lower edge), Y","kind":"length","measurements":[{"id":"left","value":1.519,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 21bd55fd00b4 (Aero's gallery: the M4E1 Threaded stripped upper in FDE Cerakote, APAR700202C, its left side, straight on, 1000 x 630: the same forging in the colour that shows relief)","scaleRef":"its own lug holes on the standard pin spacing (std.ar15.pin_spacing): the takedown hole's centre at (883.8, 424.6) px, the pivot hole's near rim centred 123.5: 119.2 px/in ± 0.3 (the black left view in the same pose, 05049cf3016d: 119.17); the frame checked on the underside (395 px: 0.248 for the drawing's 0.2485), the rail's top (176 px: 2.086 for 2.09) and the front face (45 px: 7.03 for 7.036). The holes are on the centre plane and the wall read is about half an inch nearer the lens: the ± covers it","method":"columns 258 to 286: the lit face above (183 to 208) gives way to the outer face (146 to 149) between 242 and 246 px, the half level at 243.5; rows 241 and 245 left and right of the face: its ends' lit faces stop at the same height (the band's tone below, and a shadow under the rear one): (424.6 - 243.5) / 119.2","via":"harvest"}}]},"cam_boss_bottom_y":{"label":"The cam pin's boss, its outer face's lower edge, where it runs out on the body's sloped face, Y","kind":"length","measurements":[{"id":"left","value":1.21,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 21bd55fd00b4 (Aero's gallery: the M4E1 Threaded stripped upper in FDE Cerakote, APAR700202C, its left side, straight on, 1000 x 630: the same forging in the colour that shows relief)","scaleRef":"its own lug holes on the standard pin spacing (std.ar15.pin_spacing): the takedown hole's centre at (883.8, 424.6) px, the pivot hole's near rim centred 123.5: 119.2 px/in ± 0.3 (the black left view in the same pose, 05049cf3016d: 119.17); the frame checked on the underside (395 px: 0.248 for the drawing's 0.2485), the rail's top (176 px: 2.086 for 2.09) and the front face (45 px: 7.03 for 7.036). The holes are on the centre plane and the wall read is about half an inch nearer the lens: the ± covers it","method":"columns 258 to 286: the outer face (140 to 143) gives way to the sloped face (186) between 278 and 282 px, the half level at 280.4: (424.6 - 280.4) / 119.2","via":"harvest"}}],"note":"The flanks beside the outer face narrow to nothing here (rows 256 to 279: the left one from 12.5 px wide to none), as the flanks of an upright face do where it meets a face sloping out to it. The script takes the outer face to stand where the sloped face is at this height: 0.068 in out from the band with the section as drawn (side_half_width, side_bottom_y, shoulder_bottom_y, width)."},"cam_boss_top_y":{"label":"The cam pin's boss, its upper edge on the band under the rail, Y","kind":"length","measurements":[{"id":"left","value":1.648,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 21bd55fd00b4 (Aero's gallery: the M4E1 Threaded stripped upper in FDE Cerakote, APAR700202C, its left side, straight on, 1000 x 630: the same forging in the colour that shows relief)","scaleRef":"its own lug holes on the standard pin spacing (std.ar15.pin_spacing): the takedown hole's centre at (883.8, 424.6) px, the pivot hole's near rim centred 123.5: 119.2 px/in ± 0.3 (the black left view in the same pose, 05049cf3016d: 119.17); the frame checked on the underside (395 px: 0.248 for the drawing's 0.2485), the rail's top (176 px: 2.086 for 2.09) and the front face (45 px: 7.03 for 7.036). The holes are on the centre plane and the wall read is about half an inch nearer the lens: the ± covers it","method":"columns 248 to 286: the band (127 to 131) gives way to the lit face (188 to 195) between 226 and 230 px, the half level at 228.2: (424.6 - 228.2) / 119.2","via":"harvest"}}]},"cam_boss_top_half_width":{"label":"The cam pin's boss, its upper edge, half its length","kind":"length","measurements":[{"id":"left","value":0.245,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 21bd55fd00b4 (Aero's gallery: the M4E1 Threaded stripped upper in FDE Cerakote, APAR700202C, its left side, straight on, 1000 x 630: the same forging in the colour that shows relief)","scaleRef":"its own lug holes on the standard pin spacing (std.ar15.pin_spacing): the takedown hole's centre at (883.8, 424.6) px, the pivot hole's near rim centred 123.5: 119.2 px/in ± 0.3 (the black left view in the same pose, 05049cf3016d: 119.17); the frame checked on the underside (395 px: 0.248 for the drawing's 0.2485), the rail's top (176 px: 2.086 for 2.09) and the front face (45 px: 7.03 for 7.036). The holes are on the centre plane and the wall read is about half an inch nearer the lens: the ± covers it","method":"row 229: lit from 242.5 to 301 px (half levels): 58.5 px / 119.2 / 2","via":"harvest"}}]},"cam_boss_ear_half_width":{"label":"The cam pin's boss, its two ends at their lower edge, half the length between them","kind":"length","measurements":[{"id":"left","value":0.373,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 21bd55fd00b4 (Aero's gallery: the M4E1 Threaded stripped upper in FDE Cerakote, APAR700202C, its left side, straight on, 1000 x 630: the same forging in the colour that shows relief)","scaleRef":"its own lug holes on the standard pin spacing (std.ar15.pin_spacing): the takedown hole's centre at (883.8, 424.6) px, the pivot hole's near rim centred 123.5: 119.2 px/in ± 0.3 (the black left view in the same pose, 05049cf3016d: 119.17); the frame checked on the underside (395 px: 0.248 for the drawing's 0.2485), the rail's top (176 px: 2.086 for 2.09) and the front face (45 px: 7.03 for 7.036). The holes are on the centre plane and the wall read is about half an inch nearer the lens: the ± covers it","method":"rows 239 to 243: the lit faces at its ends reach 227.3 px ahead and 316.2 behind (half levels; from the upper edge's ends they run out on straight diagonals, 15 px along for 12 down, both sides alike): 88.9 px / 119.2 / 2","via":"harvest"}}]},"cam_boss_flank_run":{"label":"The cam pin's boss, how far along the body each flank of its outer face runs before it reaches the band","kind":"length","measurements":[{"id":"left","value":0.135,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 21bd55fd00b4 (Aero's gallery: the M4E1 Threaded stripped upper in FDE Cerakote, APAR700202C, its left side, straight on, 1000 x 630: the same forging in the colour that shows relief)","scaleRef":"its own lug holes on the standard pin spacing (std.ar15.pin_spacing): the takedown hole's centre at (883.8, 424.6) px, the pivot hole's near rim centred 123.5: 119.2 px/in ± 0.3 (the black left view in the same pose, 05049cf3016d: 119.17); the frame checked on the underside (395 px: 0.248 for the drawing's 0.2485), the rail's top (176 px: 2.086 for 2.09) and the front face (45 px: 7.03 for 7.036). The holes are on the centre plane and the wall read is about half an inch nearer the lens: the ± covers it","method":"the dark flank ahead of the outer face is 12.5 px wide at row 256, 8.5 at 262, 6 at 268, 3.5 at 274, 2 at 277 and gone by 280.4: a straight line, 14.7 px at the sloped face's upper edge (row 252), 0.123 in; the one behind it 17.5 px there, 0.147, with the boss's own shadow in it. The middle of the two","via":"harvest"}}],"note":"Each flank is taken as one upright flat from the outer face's edge to the band (the left one's edge on the sloped face is a straight line in the photo, as such a flat's is). The two aren't told apart: the rear one's reading has a cast shadow in it."},"left_pad_rear_x":{"label":"The flat pad low on the left wall, its rear end, X","kind":"length","measurements":[{"id":"left","value":3.077,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 21bd55fd00b4 (Aero's gallery: the M4E1 Threaded stripped upper in FDE Cerakote, APAR700202C, its left side, straight on, 1000 x 630: the same forging in the colour that shows relief)","scaleRef":"its own lug holes on the standard pin spacing (std.ar15.pin_spacing): the takedown hole's centre at (883.8, 424.6) px, the pivot hole's near rim centred 123.5: 119.2 px/in ± 0.3 (the black left view in the same pose, 05049cf3016d: 119.17); the frame checked on the underside (395 px: 0.248 for the drawing's 0.2485), the rail's top (176 px: 2.086 for 2.09) and the front face (45 px: 7.03 for 7.036). The holes are on the centre plane and the wall read is about half an inch nearer the lens: the ± covers it","method":"rows 352, 370 and 388: the pad's tone (137 to 148) falls to the wall's behind it at 518.2, 516.5 and 516.5 px (half levels), and a shadow 12 px wide lies on the wall behind that end at row 388 (127 for the wall's 139): 517 px, (883.8 - 517) / 119.2","via":"harvest"}}],"note":"An upright flat along the foot of the left wall, from over the magazine well back past the bolt catch, in three lengths: the middle one stands further out and reaches higher. Raised, not sunk: its upper edge is a crease with no shadow under it (columns 200 to 480: the sloped under-face's 120 steps to 130 and climbs to 145, as the plain lug wall's does behind the pad at 376 px), its rear end and the middle length's rear end throw a shadow rearward onto what is behind them (light from the upper front), and a buyer's photo of it on a rifle from above (d4da1497f915) has the middle length's foot lower in the picture than its neighbours'. How far it stands out is in no view: the script takes each length to stand where the body as drawn is at its upper edge's height."},"left_pad_front_x":{"label":"The flat pad low on the left wall, its front end, X","kind":"length","measurements":[{"id":"left","value":6.202,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 21bd55fd00b4 (Aero's gallery: the M4E1 Threaded stripped upper in FDE Cerakote, APAR700202C, its left side, straight on, 1000 x 630: the same forging in the colour that shows relief)","scaleRef":"its own lug holes on the standard pin spacing (std.ar15.pin_spacing): the takedown hole's centre at (883.8, 424.6) px, the pivot hole's near rim centred 123.5: 119.2 px/in ± 0.3 (the black left view in the same pose, 05049cf3016d: 119.17); the frame checked on the underside (395 px: 0.248 for the drawing's 0.2485), the rail's top (176 px: 2.086 for 2.09) and the front face (45 px: 7.03 for 7.036). The holes are on the centre plane and the wall read is about half an inch nearer the lens: the ± covers it","method":"rows 352 and 370: the pad's tone begins at 144 and 145 px (half levels; at row 370 a band 8 px wide of a tone between lies ahead of it, an end face or its round, not drawn): 144.5 px, (883.8 - 144.5) / 119.2","via":"harvest"}}]},"left_pad_top_y":{"label":"The flat pad low on the left wall, the upper edge of its front and rear lengths, Y","kind":"length","measurements":[{"id":"left","value":0.662,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 21bd55fd00b4 (Aero's gallery: the M4E1 Threaded stripped upper in FDE Cerakote, APAR700202C, its left side, straight on, 1000 x 630: the same forging in the colour that shows relief)","scaleRef":"its own lug holes on the standard pin spacing (std.ar15.pin_spacing): the takedown hole's centre at (883.8, 424.6) px, the pivot hole's near rim centred 123.5: 119.2 px/in ± 0.3 (the black left view in the same pose, 05049cf3016d: 119.17); the frame checked on the underside (395 px: 0.248 for the drawing's 0.2485), the rail's top (176 px: 2.086 for 2.09) and the front face (45 px: 7.03 for 7.036). The holes are on the centre plane and the wall read is about half an inch nearer the lens: the ± covers it","method":"columns 200, 250, 300, 440 and 480 (7 px wide each): the dark under-face (120 to 122) steps to the pad's tone (129 to 136) between 344 and 348 px in all five, the half level at 345.7: (424.6 - 345.7) / 119.2","via":"harvest"}}],"note":"Behind the pad the plain wall's own crease is at 376 px, 0.408 in above the pin line (columns 560 to 780), with one even dark tone above it up to the widest line: a flat face sloping in, where the model has the mil-spec forging's round body meeting its lug walls at 0.50. Not changed in this pass (the part's first gap): with the body flat there the pad would stand 0.075 in out from the lug wall, and with the round one it is 0.096."},"left_pad_step_rear_x":{"label":"The flat pad low on the left wall, its middle length's rear end, X","kind":"length","measurements":[{"id":"left","value":4.05,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 21bd55fd00b4 (Aero's gallery: the M4E1 Threaded stripped upper in FDE Cerakote, APAR700202C, its left side, straight on, 1000 x 630: the same forging in the colour that shows relief)","scaleRef":"its own lug holes on the standard pin spacing (std.ar15.pin_spacing): the takedown hole's centre at (883.8, 424.6) px, the pivot hole's near rim centred 123.5: 119.2 px/in ± 0.3 (the black left view in the same pose, 05049cf3016d: 119.17); the frame checked on the underside (395 px: 0.248 for the drawing's 0.2485), the rail's top (176 px: 2.086 for 2.09) and the front face (45 px: 7.03 for 7.036). The holes are on the centre plane and the wall read is about half an inch nearer the lens: the ± covers it","method":"rows 340 and 344 (above the other lengths' upper edge): the middle length's tone (136 to 141) falls to the under-face's (121) at 401.5 and 400.7 px (half levels); at row 370 a shadow lies behind that end, 401 to 407 px (130 for 143): 401 px, (883.8 - 401) / 119.2","via":"harvest"}}]},"left_pad_step_front_x":{"label":"The flat pad low on the left wall, its middle length's front end, X","kind":"length","measurements":[{"id":"left","value":4.585,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 21bd55fd00b4 (Aero's gallery: the M4E1 Threaded stripped upper in FDE Cerakote, APAR700202C, its left side, straight on, 1000 x 630: the same forging in the colour that shows relief)","scaleRef":"its own lug holes on the standard pin spacing (std.ar15.pin_spacing): the takedown hole's centre at (883.8, 424.6) px, the pivot hole's near rim centred 123.5: 119.2 px/in ± 0.3 (the black left view in the same pose, 05049cf3016d: 119.17); the frame checked on the underside (395 px: 0.248 for the drawing's 0.2485), the rail's top (176 px: 2.086 for 2.09) and the front face (45 px: 7.03 for 7.036). The holes are on the centre plane and the wall read is about half an inch nearer the lens: the ± covers it","method":"rows 340 and 344: the under-face's 119 to 121 rises to the middle length's 136 to 138 at 337.5 and 337 px (half levels): 337.3 px, (883.8 - 337.3) / 119.2","via":"harvest"}}]},"left_pad_step_top_y":{"label":"The flat pad low on the left wall, its middle length's upper edge, Y","kind":"length","measurements":[{"id":"left","value":0.743,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aero-m4e1-threaded-upper 21bd55fd00b4 (Aero's gallery: the M4E1 Threaded stripped upper in FDE Cerakote, APAR700202C, its left side, straight on, 1000 x 630: the same forging in the colour that shows relief)","scaleRef":"its own lug holes on the standard pin spacing (std.ar15.pin_spacing): the takedown hole's centre at (883.8, 424.6) px, the pivot hole's near rim centred 123.5: 119.2 px/in ± 0.3 (the black left view in the same pose, 05049cf3016d: 119.17); the frame checked on the underside (395 px: 0.248 for the drawing's 0.2485), the rail's top (176 px: 2.086 for 2.09) and the front face (45 px: 7.03 for 7.036). The holes are on the centre plane and the wall read is about half an inch nearer the lens: the ± covers it","method":"columns 360 and 380 (7 px wide each): the dark under-face (120 to 122) steps to the pad's tone (137 to 139) between 334 and 338 px, the half level at 336: (424.6 - 336) / 119.2","via":"harvest"}}]}}},{"subject":"aero-mid-gas-tube","title":"Aero Precision gas tube, mid-length, stainless steel (APRH100144C)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"aero","value":0.64,"unit":"oz","pm":0.005,"stated":"Weight(s) 0.64 oz","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, Gas Tube, Mid-Length - Stainless Steel (APRH100144C), Specifications","url":"https://www.aeroprecisionusa.com/gas-tube-mid-length-stainless-steel","retrieved":"2026-10-02","via":"harvest"}}]},"length":{"label":"Length","kind":"length","measurements":[{"id":"aero","value":11.75,"unit":"in","pm":0.01,"stated":"11.75\"","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, Gas Tube, Mid-Length - Stainless Steel (APRH100144C), Features","url":"https://www.aeroprecisionusa.com/gas-tube-mid-length-stainless-steel","retrieved":"2026-10-02","via":"harvest"}}],"note":"Aero's feature list says only \"11.75\"\" on the page of a tube it names mid-length; the discovery report found the same figure labelled on the Melonite tube's page (\"Mid-Length 11.75\"\")."},"od":{"label":"Outside diameter","kind":"length","measurements":[{"id":"tdp","value":0.18,"unit":"in","pm":0.002,"stated":".1800 DIA REF","source":{"type":"standard","doc":"US Army TDP drawing 8448567 (Gas Tube Assembly), PDF page 144, both ends"},"note":"A REF figure, the tube stock's size; .179 is allowed at its bends."}],"note":"Aero gives none; the tube is the standard's (the key's socket takes a .180 tube)."},"bend_offset":{"label":"How far the tube drops at its bend (its rear run above its front)","kind":"length","measurements":[{"id":"tdp","value":0.156,"unit":"in","pm":0.01,"stated":"offset .156","source":{"type":"standard","doc":"US Army TDP drawing 8448567 (Gas Tube Assembly), rev F (the rifle's tube; R 1.50 ±.50); user-supplied scan, PDF page 144","via":"user"}},{"id":"photo","value":0.17,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-mid-gas-tube 7b502f23841c (Aero's gallery: the tube from the side, 1000 x 630)","scaleRef":"its published length over the silhouette's 831 px: 70.7 px/in","method":"the straight runs' centres, px rows 302.5 (rear) and 314.5 (front)","via":"harvest"}},{"id":"photo-fit","value":0.163,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/aero-mid-gas-tube 7b502f23841c (Aero's gallery: the tube from the side, the plugged front end at the right, 1000 x 630; a419898ca923 is the same photograph on a square ground and reads the same)","scaleRef":"its published length between the end faces, 831.2 px (columns 86.5 to 917.7 at the 225 level): 70.7 px/in, a pixel 0.014 in","method":"a level run, a round, a straight slope, an equal round and a level run fitted to the centre line (each column's upper and lower edge at the 200 and 225 levels, both copies): the drop reads 0.1632, 0.1619, 0.1641 and 0.1625","via":"harvest"},"note":"The 0.17 above is the same photo by two rows picked by eye."}],"adopt":{"from":"tdp","reason":"The drawing; the photo agrees. It takes the tube from the receiver's .781 down to the block's .625."}},"bend_radius":{"label":"The radius of each of the bend's two rounds, at the tube's centre line","kind":"length","measurements":[{"id":"photo","value":4.2,"unit":"in","pm":0.4,"source":{"type":"photo","photo":"references/aero-mid-gas-tube 7b502f23841c (Aero's gallery: the tube from the side, the plugged front end at the right, 1000 x 630; a419898ca923 is the same photograph on a square ground and reads the same)","scaleRef":"its published length between the end faces, 831.2 px (columns 86.5 to 917.7 at the 225 level): 70.7 px/in, a pixel 0.014 in","method":"a level run, a round, a straight slope, an equal round and a level run fitted to the centre line with the radius left free: 4.00 and 4.34 (edges at the 200 and 225 levels), 4.39 and 4.38 in the other copy; the slope between the rounds 6.25 to 6.3 degrees and 1.0 in long, the fit's rms 0.8 thousandths","via":"harvest"},"note":"With the radius held at the drawing's 1.50 the fit is six tenths worse (1.3 to 1.4 thousandths rms) and puts the bend from 3.71 to 3.75 and 5.44 to 5.48. At the 240 level the edges take in the tube's shadow and the fit is three times worse: left out."}],"note":"The Army's drawing is of the rifle's tube (\"1.50 ±.50 R 2 PLACES\", 8448567; the callout is read in the carbine tube's ledger, bend_radius); where and how a mid-length tube bends is on no drawing on file, so this tube's own photo is the reading. The carbine tube's photos read 3.6."},"bend_start_from_rear":{"label":"Where the bend begins, from the tube's rear (receiver) end","kind":"length","measurements":[{"id":"photo","value":3.86,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/aero-mid-gas-tube 7b502f23841c (Aero's gallery: the tube from the side, 1000 x 630)","scaleRef":"70.7 px/in","method":"where the silhouette leaves the rear run, px 360 (the roll-pin end, at the right, is the front)","via":"harvest"},"note":"The rifle's tube bends at 4.16 ±.25 (8448567); this is the mid-length's. Where the eye sees it leave: the fitted centre line is a twentieth of the drop off the rear run at 3.89."},{"id":"photo-fit","value":3.61,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-mid-gas-tube 7b502f23841c (Aero's gallery: the tube from the side, the plugged front end at the right, 1000 x 630; a419898ca923 is the same photograph on a square ground and reads the same)","scaleRef":"its published length between the end faces, 831.2 px (columns 86.5 to 917.7 at the 225 level): 70.7 px/in, a pixel 0.014 in","method":"where the first round leaves the rear run in the fit of bend_radius (radius free): 3.607 and 3.629, 3.584 and 3.621 in the other copy; the plain end is the rear, the end with the cross hole the front","via":"harvest"},"note":"The carbine tube's own photos put its bend at 3.71: the same place from the rear end, as it has to be to clear the same barrel nut."}],"adopt":{"from":"photo-fit","reason":"Where a round of the fitted radius is tangent to the rear run, which is what the model's centre line is built from; the 3.86 is where the tube is seen to have left the run, a quarter of an inch on along a round this gentle. Two definitions of one bend, not two bends (2026-10-13)."}},"bend_end_from_rear":{"label":"Where the bend ends, from the tube's rear (receiver) end","kind":"length","measurements":[{"id":"photo","value":5.49,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/aero-mid-gas-tube 7b502f23841c (Aero's gallery: the tube from the side, 1000 x 630)","scaleRef":"70.7 px/in","method":"where the silhouette joins the front run, px 475","via":"harvest"}},{"id":"photo-fit","value":5.56,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-mid-gas-tube 7b502f23841c (Aero's gallery: the tube from the side, the plugged front end at the right, 1000 x 630; a419898ca923 is the same photograph on a square ground and reads the same)","scaleRef":"its published length between the end faces, 831.2 px (columns 86.5 to 917.7 at the 225 level): 70.7 px/in, a pixel 0.014 in","method":"where the second round joins the front run in the fit of bend_radius (radius free): 5.534 and 5.576, 5.551 and 5.583 in the other copy","via":"harvest"},"note":"The carbine tube's: 5.53. The centre line is halfway down the drop 4.57 to 4.62 in from the rear end."}],"adopt":{"from":"photo-fit","reason":"The fitted round's tangent point, as bend_start_from_rear."}},"gas_hole_from_front":{"label":"The gas hole's centre behind the tube's front end","kind":"length","measurements":[{"id":"tdp","value":0.605,"unit":"in","pm":0.004,"source":{"type":"derived","expr":"{std.ar15.gas_tube_hole_from_front}","via":"user"},"note":"The Army's drawing 8448567, \".605 REF\"."}],"note":"Where this tube touches the block: its hole over the block's port. The part's frame is here. This tube's photo doesn't show the hole (it faces the barrel, and the lower edge has no notch a pixel deep there); the carbine tube's photos show its own at 0.607."},"gas_hole_d":{"label":"The gas hole's diameter","kind":"length","measurements":[{"id":"tdp","value":0.125,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{aero-carbine-gas-tube.gas_hole_d}","via":"user"},"note":"The Army's drawing 8448567, \".125 DIA +.003 THRU THIS SIDE ONLY TO DEPTH SHOWN\": its source is in the carbine tube's ledger."}]},"pin_hole_from_front":{"label":"The roll pin's hole behind the tube's front end","kind":"length","measurements":[{"id":"tdp","value":0.187,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{aero-carbine-gas-tube.pin_hole_from_front}","via":"user"},"note":"The Army's drawing 8448567, \".187 ±.003\": its source is in the carbine tube's ledger."},{"id":"photo","value":0.2,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aero-mid-gas-tube 7b502f23841c (Aero's gallery: the tube from the side, the plugged front end at the right, 1000 x 630; a419898ca923 is the same photograph on a square ground and reads the same)","scaleRef":"its published length between the end faces, 831.2 px (columns 86.5 to 917.7 at the 225 level): 70.7 px/in, a pixel 0.014 in","method":"the white ground seen through the cross hole on the tube's middle rows (level 248 to 254 where the tube beside it is 220 to 230): four columns, 0.183 to 0.225 in from the front end face, their weighted middle 0.200","via":"harvest"},"note":"Seen straight through from the side: the pin lies across the rifle, square to the plane of the bend."}],"adopt":{"from":"tdp","reason":"The drawing; the photo agrees within a pixel."}},"pin_hole_d":{"label":"The roll pin's hole, diameter","kind":"length","measurements":[{"id":"tdp","value":0.078,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{aero-carbine-gas-tube.pin_hole_d}","via":"user"},"note":"The Army's drawing 8448567, \".078 DIA +.003 THRU\": its source is in the carbine tube's ledger. In this photo the hole is four columns of white, 0.06 in."}]},"crimp_front_from_front":{"label":"The front groove round the plugged end, its middle from the front end","kind":"length","measurements":[{"id":"photo","value":0.088,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aero-mid-gas-tube 7b502f23841c (Aero's gallery: the tube from the side, the plugged front end at the right, 1000 x 630; a419898ca923 is the same photograph on a square ground and reads the same)","scaleRef":"its published length between the end faces, 831.2 px (columns 86.5 to 917.7 at the 225 level): 70.7 px/in, a pixel 0.014 in","method":"where the tube reads thinnest, column by column, near its front end: the two columns at 0.081 and 0.095 in from the end face at the 225 level (10.4 px where the columns beside them are 11.1 to 11.4), 0.073 and 0.087 at the 200 level, 0.084 and 0.098 at 235","via":"harvest"}}],"note":"The tube is closed at the front by a plug held by two grooves pressed round it, one each side of the pin's hole (the Army's drawing shows them and gives them no figure; the carbine tube's ledger has the note). Read on this tube's own photo; the carbine tube's read 0.08 and 0.295."},"crimp_rear_from_front":{"label":"The rear groove round the plugged end, its middle from the front end","kind":"length","measurements":[{"id":"photo","value":0.293,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-mid-gas-tube 7b502f23841c (Aero's gallery: the tube from the side, the plugged front end at the right, 1000 x 630; a419898ca923 is the same photograph on a square ground and reads the same)","scaleRef":"its published length between the end faces, 831.2 px (columns 86.5 to 917.7 at the 225 level): 70.7 px/in, a pixel 0.014 in","method":"where the tube reads thinnest behind the pin's hole: the columns at 0.279, 0.293 and 0.307 in from the end face at the 225 level (10.0, 10.4 and 9.2 px where the tube behind is 10.6), 0.272 to 0.300 at the 200 level, 0.296 and 0.310 at 235","via":"harvest"},"note":"Three columns with the middle one the least thin: one groove with a glint in it, or two closer than the picture can part. One is drawn."}]},"crimp_width":{"label":"A groove's width along the tube","kind":"length","measurements":[{"id":"photo","value":0.035,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aero-mid-gas-tube 7b502f23841c (Aero's gallery: the tube from the side, the plugged front end at the right, 1000 x 630; a419898ca923 is the same photograph on a square ground and reads the same)","scaleRef":"its published length between the end faces, 831.2 px (columns 86.5 to 917.7 at the 225 level): 70.7 px/in, a pixel 0.014 in","method":"the columns over which the tube reads thinner than beside the groove: two columns of 0.014 in at the front groove, three at the rear","via":"harvest"},"note":"Two to three pixels: a groove this narrow is as wide as the photo's blur."}]},"crimp_depth":{"label":"A groove's depth, as the diameter it takes off","kind":"length","measurements":[{"id":"photo","value":0.012,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/aero-mid-gas-tube 7b502f23841c (Aero's gallery: the tube from the side, the plugged front end at the right, 1000 x 630; a419898ca923 is the same photograph on a square ground and reads the same)","scaleRef":"its published length between the end faces, 831.2 px (columns 86.5 to 917.7 at the 225 level): 70.7 px/in, a pixel 0.014 in","method":"how much thinner the tube reads at a groove than on the tube beside it: 0.7 to 1.0 px at the front groove, 0.6 to 1.4 px at the rear","via":"harvest"},"note":"A pixel's blur fills a groove this narrow: it is at least this deep. The carbine tube's four photos read 0.011."}]},"head_length":{"label":"The head at the tube's rear end, its length","kind":"length","measurements":[{"id":"photo","value":0.1,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-mid-gas-tube 7b502f23841c (Aero's gallery: the tube from the side, the plugged front end at the right, 1000 x 630; a419898ca923 is the same photograph on a square ground and reads the same)","scaleRef":"its published length between the end faces, 831.2 px (columns 86.5 to 917.7 at the 225 level): 70.7 px/in, a pixel 0.014 in","method":"the columns from the rear end face over which the tube reads thicker than behind it: 10.7 to 10.9 px to 0.078 in, 10.6 at 0.092 and 10.4 from 0.106 on at the 225 level; 11.4 to 11.6 px to 0.081, 11.2 at 0.095 and 10.7 from 0.109 on at 235","via":"harvest"},"note":"The carbine tube's four photos: 0.1. Drawn at the tube's diameter, as the carbine tube's is."}],"note":"The end that enters the carrier key. The drawing shows the head and gives its length no figure."},"end_break":{"label":"The broken rim of each end face, along the tube and across it","kind":"length","measurements":[{"id":"photo","value":0.012,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/aero-mid-gas-tube 7b502f23841c (Aero's gallery: the tube from the side, the plugged front end at the right, 1000 x 630; a419898ca923 is the same photograph on a square ground and reads the same)","scaleRef":"its published length between the end faces, 831.2 px (columns 86.5 to 917.7 at the 225 level): 70.7 px/in, a pixel 0.014 in","method":"how much thinner the tube reads in the first column from each end face than two columns in: 0.6 to 0.9 px at the front, 1.5 to 3 px at the rear, within 0.014 in of the face","via":"harvest"},"note":"A pixel: as large as the picture's blur, and the rear end's the larger, as on the carbine tube. Drawn as a chamfer this size at both ends."}]},"relief_end_from_rear":{"label":"Where the thinner stretch behind the head ends, from the tube's rear end","kind":"length","measurements":[{"id":"photo","value":2.31,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/aero-mid-gas-tube 7b502f23841c (Aero's gallery: the tube from the side, the plugged front end at the right, 1000 x 630; a419898ca923 is the same photograph on a square ground and reads the same)","scaleRef":"its published length between the end faces, 831.2 px (columns 86.5 to 917.7 at the 225 level): 70.7 px/in, a pixel 0.014 in","method":"the tube's rows, column by column from the rear end: their darkest level is 111 to 116 as far as 2.30 in and 94 to 101 from 2.34 on, with the edges broken up over the five columns between (2.285 to 2.384)","via":"harvest"}}],"note":"Between its head and this station the tube is thinner than ahead of it: a line across the tube in the photo, with a different sheen behind it. The carbine tube has the same at 2.27."},"relief_depth":{"label":"How much thinner the stretch behind the head is than the tube ahead of it, on the diameter","kind":"length","measurements":[{"id":"photo","value":0.008,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/aero-mid-gas-tube 7b502f23841c (Aero's gallery: the tube from the side, the plugged front end at the right, 1000 x 630; a419898ca923 is the same photograph on a square ground and reads the same)","scaleRef":"its published length between the end faces, 831.2 px (columns 86.5 to 917.7 at the 225 level): 70.7 px/in, a pixel 0.014 in","method":"the median thickness over 0.2 to 2.1 in from the rear end against that over 2.4 to 3.4 in: 0.61, 0.41 and 0.56 px less at the 200, 225 and 235 levels","via":"harvest"},"note":"Half a pixel, the same way at three levels; the carbine tube's four photos, at finer scales, read 0.013. Which of the two stretches is the drawing's .180 isn't read: the head and the tube ahead of the relief are drawn at it, and the relief this much under."}]},"plug_length":{"label":"The plug in the front end, its length from the front end face","kind":"length","measurements":[{"id":"tdp","value":0.44,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{aero-carbine-gas-tube.plug_length}","via":"user"},"note":"The Army's drawing 8448567, the view from below, scaled: the reading is in the carbine tube's ledger. It ends ahead of the gas hole's front edge (0.54 from the end), as it must."}],"note":"Where the tube's bore ends. Not a callout: the plug's own drawing (8448568) isn't in the package."},"bore":{"label":"The tube's bore","kind":"length","measurements":[{"id":"weight","value":0.13,"unit":"in","pm":0.003,"source":{"type":"derived","basis":"The bore of a plain tube of this length (11.75 in) and diameter (.180) that weighs Aero's 0.64 oz as stainless steel at std.density.stainless_416 (127 g to the cubic inch): 18.14 g is 0.1429 cubic inches, a wall of 0.01216 square inches, which leaves a bore of 0.1301. By the weight's half digit (0.635 to 0.645 oz): 0.1306 to 0.1296; as a 304 stainless, 2 percent denser: 0.131. The plug, the relief and the holes are left out of it.","via":"harvest"},"note":"Aero names no grade of stainless. It shows only at the tube's open rear end, inside the receiver."}],"note":"No page and no callout gives it. The Army's section as drawn, without a figure, has 0.09 (the reading is in the carbine tube's ledger, bore); a tube with that bore would weigh 1.0 oz at this length, and Aero says 0.64. The carbine tube's own weight (0.5 oz, given to a tenth) leaves 0.134."}}},{"subject":"aero-r-one-10-3-handguard","title":"Aero Precision AR15 10.3 in R-ONE M-LOK handguard (APRA500703A)","dimensions":{"weight":{"label":"Weight (the handguard; its mounting hardware is listed apart)","kind":"mass","measurements":[{"id":"aero","value":6.7,"unit":"oz","pm":0.01,"stated":"Weight(s) 6.7 oz","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, AR15 10.3\" R-ONE M-LOK Handguard, Specifications","url":"https://www.aeroprecisionusa.com/ar15-10-3-atlas-r-one-m-lok-handguard-anodized-black","retrieved":"2026-11-03","via":"harvest"}}]},"length":{"label":"Length (the receiver's face to the end of the last rail slot)","kind":"length","measurements":[{"id":"aero","value":10.3,"unit":"in","pm":0.05,"stated":"Handguard Length 10.3\"","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, AR15 10.3\" R-ONE M-LOK Handguard, Specifications","url":"https://www.aeroprecisionusa.com/ar15-10-3-atlas-r-one-m-lok-handguard-anodized-black","retrieved":"2026-11-03","via":"harvest"}}],"note":"Aero: \"Aero Precision rail lengths measure from end to end. This is the point of contact at the receiver to the end of the last picatinny slot at the muzzle.\""},"overall_length":{"label":"Overall length, end to end","kind":"length","measurements":[{"id":"photo","value":10.687,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-10-3-handguard 3e023c5c8f00 (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 631)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 33.586 px a tooth, 85.24 px/in","method":"the silhouette end to end, 911 px","via":"harvest"}},{"id":"photo-right","value":10.667,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-10-3-handguard b42ac1f62a4b (Aero's gallery: the R-ONE's right side, the check, 1000 x 631)","scaleRef":"its own rail teeth fitted to the same pitch","method":"the silhouette end to end","via":"harvest"}}],"adopt":{"from":"photo","reason":"The left view, the one traced (the 15 in's was traced from the same view); the right view's reading is within its ±."}},"rail_slots":{"label":"Slots in its top rail","kind":"count","measurements":[{"id":"photo","value":25,"unit":"count","source":{"type":"photo","photo":"references/aero-r-one-10-3-handguard 3e023c5c8f00 (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 631)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 33.586 px a tooth, 85.24 px/in","method":"the gaps between the teeth along the whole rail, counted; they lie on the Picatinny pitch end to end within 0.02 in","via":"harvest"}},{"id":"photo-right","value":25,"unit":"count","source":{"type":"photo","photo":"references/aero-r-one-10-3-handguard b42ac1f62a4b (Aero's gallery: the R-ONE's right side, the check, 1000 x 631)","scaleRef":"its own rail teeth fitted to the same pitch","method":"counted","via":"harvest"}}],"adopt":{"from":"photo","reason":"Both views read the same; the left view's is the one traced (the 15 in's was traced from the same view)."}},"rail_slot0_from_rear":{"label":"Its rail's rearmost slot (its centre) ahead of the outline's rear end","kind":"length","measurements":[{"id":"photo","value":0.821,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-10-3-handguard 3e023c5c8f00 (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 631)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 33.586 px a tooth, 85.24 px/in","method":"the first gap between the teeth, its own centre (on the 15 in's view this reads 0.842 for that ledger's 0.855)","via":"harvest"}},{"id":"photo-right","value":0.827,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-10-3-handguard b42ac1f62a4b (Aero's gallery: the R-ONE's right side, the check, 1000 x 631)","scaleRef":"its own rail teeth fitted to the same pitch","method":"the same","via":"harvest"}}],"adopt":{"from":"photo","reason":"The left view, the one traced (the 15 in's was traced from the same view); the right view's reading is within its ±."}},"rail_front_from_rear":{"label":"Its rail's front end (the end of the last slot) ahead of the outline's rear end","kind":"length","measurements":[{"id":"photo","value":10.628,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-r-one-10-3-handguard 3e023c5c8f00 (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 631)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 33.586 px a tooth, 85.24 px/in","method":"the rail's top's last solid column ahead of its last slot","via":"harvest"}}]},"qd_socket_from_rear":{"label":"The QD sling socket on each side (3 and 9 o'clock), its centre ahead of the outline's rear end","kind":"length","measurements":[{"id":"photo","value":2.675,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/aero-r-one-10-3-handguard 3e023c5c8f00 (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 631)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 33.586 px a tooth, 85.24 px/in","method":"the round hole behind the M-LOK row, what shows through both walls","via":"harvest"}},{"id":"photo-right","value":2.675,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/aero-r-one-10-3-handguard b42ac1f62a4b (Aero's gallery: the R-ONE's right side, the check, 1000 x 631)","scaleRef":"its own rail teeth fitted to the same pitch","method":"the same","via":"harvest"}}],"adopt":{"from":"photo","reason":"Both views read the same; the left view's is the one traced (the 15 in's was traced from the same view)."}},"short_slot_length":{"label":"The short slot's length (at least: what shows through both walls)","kind":"length","measurements":[{"id":"photo","value":0.54,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-10-3-handguard 3e023c5c8f00 (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 631)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 33.586 px a tooth, 85.24 px/in","method":"the shorter slot between the QD socket and the M-LOK row: what shows through both walls","via":"harvest"}},{"id":"photo-right","value":0.505,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-10-3-handguard b42ac1f62a4b (Aero's gallery: the R-ONE's right side, the check, 1000 x 631)","scaleRef":"its own rail teeth fitted to the same pitch","method":"the same","via":"harvest"}}],"adopt":{"from":"photo","reason":"The longer reading: a slot seen through both walls at a slant shows less than it is, never more."}},"short_slot_rear_from_rear":{"label":"The short slot's rear end ahead of the outline's rear end","kind":"length","measurements":[{"id":"derived","value":3.432,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"3.702in - {.short_slot_length} / 2","via":"harvest"},"note":"Its centre on the left view, 3.702 in (the right view: 3.701)."}]},"mlok_slots":{"label":"How many M-LOK slots on each side","kind":"count","measurements":[{"id":"photo","value":4,"unit":"count","source":{"type":"photo","photo":"references/aero-r-one-10-3-handguard 3e023c5c8f00 (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 631)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 33.586 px a tooth, 85.24 px/in","method":"counted: the full-length slots in the row at the bore's level","via":"harvest"}},{"id":"photo-right","value":4,"unit":"count","source":{"type":"photo","photo":"references/aero-r-one-10-3-handguard b42ac1f62a4b (Aero's gallery: the R-ONE's right side, the check, 1000 x 631)","scaleRef":"its own rail teeth fitted to the same pitch","method":"counted","via":"harvest"}}],"adopt":{"from":"photo","reason":"Both views read the same; the left view's is the one traced (the 15 in's was traced from the same view)."}},"mlok_slot0_from_rear":{"label":"The rearmost M-LOK slot's centre on its sides, ahead of the handguard's rear end (its outline's x = 0)","kind":"length","measurements":[{"id":"photo","value":4.931,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-10-3-handguard 3e023c5c8f00 (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 631)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 33.586 px a tooth, 85.24 px/in","method":"the full-length slots' centres along their row, on the M-LOK pitch (std.mlok.slot_pitch) within 0.3%","via":"harvest"}},{"id":"photo-right","value":4.936,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-10-3-handguard b42ac1f62a4b (Aero's gallery: the R-ONE's right side, the check, 1000 x 631)","scaleRef":"its own rail teeth fitted to the same pitch","method":"the same","via":"harvest"}}],"adopt":{"from":"photo","reason":"The left view, the one traced (the 15 in's was traced from the same view); the right view's reading is within its ±."}},"mlok_slot0_x":{"label":"The rearmost M-LOK slot's centre ahead of the receiver's face","kind":"length","measurements":[{"id":"derived","value":4.168,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.rear_x} + {.mlok_slot0_from_rear}","via":"harvest"}}]},"thin_slot_count":{"label":"Thin slots in each row","kind":"count","measurements":[{"id":"photo","value":8,"unit":"count","source":{"type":"photo","photo":"references/aero-r-one-10-3-handguard 3e023c5c8f00 (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 631)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 33.586 px a tooth, 85.24 px/in","method":"counted in each of the four rows","via":"harvest"}},{"id":"photo-right","value":8,"unit":"count","source":{"type":"photo","photo":"references/aero-r-one-10-3-handguard b42ac1f62a4b (Aero's gallery: the R-ONE's right side, the check, 1000 x 631)","scaleRef":"its own rail teeth fitted to the same pitch","method":"counted","via":"harvest"}}],"adopt":{"from":"photo","reason":"Both views read the same; the left view's is the one traced (the 15 in's was traced from the same view)."}},"thin_slot_first_from_rear":{"label":"The thin slots' first centre ahead of the outline's rear end (all four rows)","kind":"length","measurements":[{"id":"photo","value":3.016,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-10-3-handguard 3e023c5c8f00 (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 631)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 33.586 px a tooth, 85.24 px/in","method":"the see-through slots' centres in the four rows fitted to one pitch","via":"harvest"}},{"id":"photo-right","value":3.018,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-10-3-handguard b42ac1f62a4b (Aero's gallery: the R-ONE's right side, the check, 1000 x 631)","scaleRef":"its own rail teeth fitted to the same pitch","method":"the same","via":"harvest"}}],"adopt":{"from":"photo","reason":"The left view, the one traced (the 15 in's was traced from the same view); the right view's reading is within its ±."}},"thin_slot_pitch":{"label":"The thin slots' pitch","kind":"length","measurements":[{"id":"photo","value":1.003,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/aero-r-one-10-3-handguard 3e023c5c8f00 (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 631)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 33.586 px a tooth, 85.24 px/in","method":"their centres' spacing in the four rows","via":"harvest"}}],"note":"Each length's own: the slots are spread over its length (the 15 in's 1.0685, this one's the one read here)."},"thin_slot_length":{"label":"A thin slot's length (at least: what shows through both walls)","kind":"length","measurements":[{"id":"photo","value":0.903,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-r-one-10-3-handguard 3e023c5c8f00 (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 631)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 33.586 px a tooth, 85.24 px/in","method":"the longest see-through slot in the four rows","via":"harvest"}}]},"rear_x":{"label":"The handguard's rear end (its two side tabs' ends) against the receiver's front face (negative: behind it)","kind":"length","measurements":[{"id":"family","value":-0.763,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rear_x}","via":"harvest"}}],"note":"The clamp is the family's: the 15 in's place by reference. On this length's view the first tooth's rear face is 0.504 in ahead of the tabs' ends (the 15 in's, read the same way, 0.517); and Aero's length, back from the rail's end, puts the receiver's face 0.328 in ahead of them where the 15 in's puts it 0.318: within what a length stated to a tenth (0.05) and the two readings (0.02 each) carry."},"rail_top_above_bore":{"label":"Its rail's top above the bore (level with the receiver's)","kind":"length","measurements":[{"id":"family","value":1.2125,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rail_top_above_bore}","via":"harvest"}}]},"width":{"label":"The R-ONE family: the 15 in's width","kind":"length","measurements":[{"id":"family","value":1.5,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.width}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"height":{"label":"The R-ONE family: the 15 in's height","kind":"length","measurements":[{"id":"family","value":1.95,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.height}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"inside_diameter":{"label":"The R-ONE family: the 15 in's inside diameter","kind":"length","measurements":[{"id":"family","value":1.3,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.inside_diameter}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"inside_height":{"label":"The R-ONE family: the 15 in's inside height","kind":"length","measurements":[{"id":"family","value":1.65,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.inside_height}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"bottom_flat_width":{"label":"The R-ONE family: the 15 in's bottom flat width","kind":"length","measurements":[{"id":"family","value":0.609,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.bottom_flat_width}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"side_top_width":{"label":"The R-ONE family: the 15 in's side top width","kind":"length","measurements":[{"id":"family","value":1.455,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.side_top_width}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"lower_edge_width":{"label":"The R-ONE family: the 15 in's lower edge width","kind":"length","measurements":[{"id":"family","value":1.133,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.lower_edge_width}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"lower_edge_below_rail_top":{"label":"The R-ONE family: the 15 in's lower edge below rail top","kind":"length","measurements":[{"id":"family","value":1.759,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.lower_edge_below_rail_top}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"rail_neck_width":{"label":"The R-ONE family: the 15 in's rail neck width","kind":"length","measurements":[{"id":"family","value":0.62,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rail_neck_width}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"rail_neck_foot_below_rail_top":{"label":"The R-ONE family: the 15 in's rail neck foot below rail top","kind":"length","measurements":[{"id":"family","value":0.377,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rail_neck_foot_below_rail_top}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"rail_centre_gap":{"label":"The R-ONE family: the 15 in's rail centre gap","kind":"length","measurements":[{"id":"family","value":0.365,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rail_centre_gap}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"rail_window_length":{"label":"The R-ONE family: the 15 in's rail window length","kind":"length","measurements":[{"id":"family","value":0.54,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rail_window_length}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"rail_bridge_recess":{"label":"The R-ONE family: the 15 in's rail bridge recess","kind":"length","measurements":[{"id":"family","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rail_bridge_recess}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"side_flat_top_below_rail_top":{"label":"The R-ONE family: the 15 in's side flat top below rail top","kind":"length","measurements":[{"id":"family","value":0.88,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.side_flat_top_below_rail_top}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"side_flat_bottom_below_rail_top":{"label":"The R-ONE family: the 15 in's side flat bottom below rail top","kind":"length","measurements":[{"id":"family","value":1.502,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.side_flat_bottom_below_rail_top}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"thin_slot_width":{"label":"The R-ONE family: the 15 in's thin slot width","kind":"length","measurements":[{"id":"family","value":0.22,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.thin_slot_width}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"thin_slot_row_a_y":{"label":"The R-ONE family: the 15 in's thin slot row a y","kind":"length","measurements":[{"id":"family","value":0.71,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.thin_slot_row_a_y}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"thin_slot_row_b_y":{"label":"The R-ONE family: the 15 in's thin slot row b y","kind":"length","measurements":[{"id":"family","value":0.46,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.thin_slot_row_b_y}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"thin_slot_row_d_y":{"label":"The R-ONE family: the 15 in's thin slot row d y","kind":"length","measurements":[{"id":"family","value":-0.41,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.thin_slot_row_d_y}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"thin_slot_row_e_y":{"label":"The R-ONE family: the 15 in's thin slot row e y","kind":"length","measurements":[{"id":"family","value":-0.635,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.thin_slot_row_e_y}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"qd_socket_d":{"label":"The R-ONE family: the 15 in's qd socket d","kind":"length","measurements":[{"id":"family","value":0.37,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.qd_socket_d}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"reach_inside":{"label":"The room inside its side faces before the barrel, at the M-LOK slots (what an accessory's nuts may take)","kind":"length","measurements":[],"note":"Not read: as on the 15 in, it depends on the barrel under it."}}},{"subject":"aero-r-one-12-7-handguard","title":"Aero Precision AR15 12.7 in R-ONE M-LOK handguard (APRA500704A)","dimensions":{"weight":{"label":"Weight (the handguard; its mounting hardware is listed apart)","kind":"mass","measurements":[{"id":"aero","value":8,"unit":"oz","pm":0.5,"stated":"Weight(s) 8 oz","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, AR15 12.7\" R-ONE M-LOK Handguard, Specifications","url":"https://www.aeroprecisionusa.com/ar15-12-7-atlas-r-one-m-lok-handguard-od-green-anodized","retrieved":"2026-11-03","via":"harvest"}}],"note":"Read on the OD Green Anodized page (APRA501604A): Aero's page for this length in black isn't at the address its others are. A figure with no decimal: \"8 oz\"."},"length":{"label":"Length (the receiver's face to the end of the last rail slot)","kind":"length","measurements":[{"id":"aero","value":12.7,"unit":"in","pm":0.05,"stated":"Handguard Length 12.7\"","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, AR15 12.7\" R-ONE M-LOK Handguard, Specifications","url":"https://www.aeroprecisionusa.com/ar15-12-7-atlas-r-one-m-lok-handguard-od-green-anodized","retrieved":"2026-11-03","via":"harvest"}}],"note":"Aero: \"Aero Precision rail lengths measure from end to end. This is the point of contact at the receiver to the end of the last picatinny slot at the muzzle.\""},"overall_length":{"label":"Overall length, end to end","kind":"length","measurements":[{"id":"photo","value":12.998,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-12-7-handguard 8bfd4875f09d (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 630)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 27.856 px a tooth, 70.70 px/in","method":"the silhouette end to end, 919 px","via":"harvest"}},{"id":"photo-right","value":13,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-12-7-handguard e34d94e32114 (Aero's gallery: the R-ONE's right side, the check, 1000 x 630)","scaleRef":"its own rail teeth fitted to the same pitch","method":"the silhouette end to end","via":"harvest"}}],"adopt":{"from":"photo","reason":"The left view, the one traced (the 15 in's was traced from the same view); the right view's reading is within its ±."}},"rail_slots":{"label":"Slots in its top rail","kind":"count","measurements":[{"id":"photo","value":31,"unit":"count","source":{"type":"photo","photo":"references/aero-r-one-12-7-handguard 8bfd4875f09d (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 630)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 27.856 px a tooth, 70.70 px/in","method":"the gaps between the teeth along the whole rail, counted; they lie on the Picatinny pitch end to end within 0.02 in","via":"harvest"}},{"id":"photo-right","value":31,"unit":"count","source":{"type":"photo","photo":"references/aero-r-one-12-7-handguard e34d94e32114 (Aero's gallery: the R-ONE's right side, the check, 1000 x 630)","scaleRef":"its own rail teeth fitted to the same pitch","method":"counted","via":"harvest"}}],"adopt":{"from":"photo","reason":"Both views read the same; the left view's is the one traced (the 15 in's was traced from the same view)."}},"rail_slot0_from_rear":{"label":"Its rail's rearmost slot (its centre) ahead of the outline's rear end","kind":"length","measurements":[{"id":"photo","value":0.813,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-12-7-handguard 8bfd4875f09d (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 630)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 27.856 px a tooth, 70.70 px/in","method":"the first gap between the teeth, its own centre (on the 15 in's view this reads 0.842 for that ledger's 0.855)","via":"harvest"}},{"id":"photo-right","value":0.801,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-12-7-handguard e34d94e32114 (Aero's gallery: the R-ONE's right side, the check, 1000 x 630)","scaleRef":"its own rail teeth fitted to the same pitch","method":"the same","via":"harvest"}}],"adopt":{"from":"photo","reason":"The left view, the one traced (the 15 in's was traced from the same view); the right view's reading is within its ±."}},"rail_front_from_rear":{"label":"Its rail's front end (the end of the last slot) ahead of the outline's rear end","kind":"length","measurements":[{"id":"photo","value":12.97,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-r-one-12-7-handguard 8bfd4875f09d (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 630)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 27.856 px a tooth, 70.70 px/in","method":"the rail's top's last solid column ahead of its last slot","via":"harvest"}}]},"qd_socket_from_rear":{"label":"The QD sling socket on each side (3 and 9 o'clock), its centre ahead of the outline's rear end","kind":"length","measurements":[{"id":"photo","value":2.696,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/aero-r-one-12-7-handguard 8bfd4875f09d (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 630)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 27.856 px a tooth, 70.70 px/in","method":"the round hole behind the M-LOK row, what shows through both walls","via":"harvest"}},{"id":"photo-right","value":2.69,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/aero-r-one-12-7-handguard e34d94e32114 (Aero's gallery: the R-ONE's right side, the check, 1000 x 630)","scaleRef":"its own rail teeth fitted to the same pitch","method":"the same","via":"harvest"}}],"adopt":{"from":"photo","reason":"The left view, the one traced (the 15 in's was traced from the same view); the right view's reading is within its ±."}},"mlok_slots":{"label":"How many M-LOK slots on each side","kind":"count","measurements":[{"id":"photo","value":6,"unit":"count","source":{"type":"photo","photo":"references/aero-r-one-12-7-handguard 8bfd4875f09d (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 630)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 27.856 px a tooth, 70.70 px/in","method":"counted: the full-length slots in the row at the bore's level","via":"harvest"}},{"id":"photo-right","value":6,"unit":"count","source":{"type":"photo","photo":"references/aero-r-one-12-7-handguard e34d94e32114 (Aero's gallery: the R-ONE's right side, the check, 1000 x 630)","scaleRef":"its own rail teeth fitted to the same pitch","method":"counted","via":"harvest"}}],"adopt":{"from":"photo","reason":"Both views read the same; the left view's is the one traced (the 15 in's was traced from the same view)."}},"mlok_slot0_from_rear":{"label":"The rearmost M-LOK slot's centre on its sides, ahead of the handguard's rear end (its outline's x = 0)","kind":"length","measurements":[{"id":"photo","value":4.123,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-12-7-handguard 8bfd4875f09d (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 630)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 27.856 px a tooth, 70.70 px/in","method":"the full-length slots' centres along their row, on the M-LOK pitch (std.mlok.slot_pitch) within 0.3%","via":"harvest"}},{"id":"photo-right","value":4.124,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-12-7-handguard e34d94e32114 (Aero's gallery: the R-ONE's right side, the check, 1000 x 630)","scaleRef":"its own rail teeth fitted to the same pitch","method":"the same","via":"harvest"}}],"adopt":{"from":"photo","reason":"The left view, the one traced (the 15 in's was traced from the same view); the right view's reading is within its ±."}},"mlok_slot0_x":{"label":"The rearmost M-LOK slot's centre ahead of the receiver's face","kind":"length","measurements":[{"id":"derived","value":3.36,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.rear_x} + {.mlok_slot0_from_rear}","via":"harvest"}}]},"thin_slot_count":{"label":"Thin slots in each row","kind":"count","measurements":[{"id":"photo","value":10,"unit":"count","source":{"type":"photo","photo":"references/aero-r-one-12-7-handguard 8bfd4875f09d (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 630)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 27.856 px a tooth, 70.70 px/in","method":"counted in each of the four rows","via":"harvest"}},{"id":"photo-right","value":10,"unit":"count","source":{"type":"photo","photo":"references/aero-r-one-12-7-handguard e34d94e32114 (Aero's gallery: the R-ONE's right side, the check, 1000 x 630)","scaleRef":"its own rail teeth fitted to the same pitch","method":"counted","via":"harvest"}}],"adopt":{"from":"photo","reason":"Both views read the same; the left view's is the one traced (the 15 in's was traced from the same view)."}},"thin_slot_first_from_rear":{"label":"The thin slots' first centre ahead of the outline's rear end (all four rows)","kind":"length","measurements":[{"id":"photo","value":3.015,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-12-7-handguard 8bfd4875f09d (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 630)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 27.856 px a tooth, 70.70 px/in","method":"the see-through slots' centres in the four rows fitted to one pitch","via":"harvest"}},{"id":"photo-right","value":3.011,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-12-7-handguard e34d94e32114 (Aero's gallery: the R-ONE's right side, the check, 1000 x 630)","scaleRef":"its own rail teeth fitted to the same pitch","method":"the same","via":"harvest"}}],"adopt":{"from":"photo","reason":"The left view, the one traced (the 15 in's was traced from the same view); the right view's reading is within its ±."}},"thin_slot_pitch":{"label":"The thin slots' pitch","kind":"length","measurements":[{"id":"photo","value":1.038,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/aero-r-one-12-7-handguard 8bfd4875f09d (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 630)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 27.856 px a tooth, 70.70 px/in","method":"their centres' spacing in the four rows","via":"harvest"}}],"note":"Each length's own: the slots are spread over its length (the 15 in's 1.0685, this one's the one read here)."},"thin_slot_length":{"label":"A thin slot's length (at least: what shows through both walls)","kind":"length","measurements":[{"id":"photo","value":0.92,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-r-one-12-7-handguard 8bfd4875f09d (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 630)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 27.856 px a tooth, 70.70 px/in","method":"the longest see-through slot in the four rows","via":"harvest"}}]},"rear_x":{"label":"The handguard's rear end (its two side tabs' ends) against the receiver's front face (negative: behind it)","kind":"length","measurements":[{"id":"family","value":-0.763,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rear_x}","via":"harvest"}}],"note":"The clamp is the family's: the 15 in's place by reference. On this length's view the first tooth's rear face is 0.509 in ahead of the tabs' ends (the 15 in's, read the same way, 0.517); and Aero's length, back from the rail's end, puts the receiver's face 0.27 in ahead of them where the 15 in's puts it 0.318: within what a length stated to a tenth (0.05) and the two readings (0.02 each) carry."},"rail_top_above_bore":{"label":"Its rail's top above the bore (level with the receiver's)","kind":"length","measurements":[{"id":"family","value":1.2125,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rail_top_above_bore}","via":"harvest"}}]},"width":{"label":"The R-ONE family: the 15 in's width","kind":"length","measurements":[{"id":"family","value":1.5,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.width}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"height":{"label":"The R-ONE family: the 15 in's height","kind":"length","measurements":[{"id":"family","value":1.95,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.height}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"inside_diameter":{"label":"The R-ONE family: the 15 in's inside diameter","kind":"length","measurements":[{"id":"family","value":1.3,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.inside_diameter}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"inside_height":{"label":"The R-ONE family: the 15 in's inside height","kind":"length","measurements":[{"id":"family","value":1.65,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.inside_height}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"bottom_flat_width":{"label":"The R-ONE family: the 15 in's bottom flat width","kind":"length","measurements":[{"id":"family","value":0.609,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.bottom_flat_width}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"side_top_width":{"label":"The R-ONE family: the 15 in's side top width","kind":"length","measurements":[{"id":"family","value":1.455,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.side_top_width}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"lower_edge_width":{"label":"The R-ONE family: the 15 in's lower edge width","kind":"length","measurements":[{"id":"family","value":1.133,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.lower_edge_width}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"lower_edge_below_rail_top":{"label":"The R-ONE family: the 15 in's lower edge below rail top","kind":"length","measurements":[{"id":"family","value":1.759,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.lower_edge_below_rail_top}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"rail_neck_width":{"label":"The R-ONE family: the 15 in's rail neck width","kind":"length","measurements":[{"id":"family","value":0.62,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rail_neck_width}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"rail_neck_foot_below_rail_top":{"label":"The R-ONE family: the 15 in's rail neck foot below rail top","kind":"length","measurements":[{"id":"family","value":0.377,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rail_neck_foot_below_rail_top}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"rail_centre_gap":{"label":"The R-ONE family: the 15 in's rail centre gap","kind":"length","measurements":[{"id":"family","value":0.365,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rail_centre_gap}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"rail_window_length":{"label":"The R-ONE family: the 15 in's rail window length","kind":"length","measurements":[{"id":"family","value":0.54,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rail_window_length}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"rail_bridge_recess":{"label":"The R-ONE family: the 15 in's rail bridge recess","kind":"length","measurements":[{"id":"family","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rail_bridge_recess}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"side_flat_top_below_rail_top":{"label":"The R-ONE family: the 15 in's side flat top below rail top","kind":"length","measurements":[{"id":"family","value":0.88,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.side_flat_top_below_rail_top}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"side_flat_bottom_below_rail_top":{"label":"The R-ONE family: the 15 in's side flat bottom below rail top","kind":"length","measurements":[{"id":"family","value":1.502,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.side_flat_bottom_below_rail_top}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"thin_slot_width":{"label":"The R-ONE family: the 15 in's thin slot width","kind":"length","measurements":[{"id":"family","value":0.22,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.thin_slot_width}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"thin_slot_row_a_y":{"label":"The R-ONE family: the 15 in's thin slot row a y","kind":"length","measurements":[{"id":"family","value":0.71,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.thin_slot_row_a_y}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"thin_slot_row_b_y":{"label":"The R-ONE family: the 15 in's thin slot row b y","kind":"length","measurements":[{"id":"family","value":0.46,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.thin_slot_row_b_y}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"thin_slot_row_d_y":{"label":"The R-ONE family: the 15 in's thin slot row d y","kind":"length","measurements":[{"id":"family","value":-0.41,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.thin_slot_row_d_y}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"thin_slot_row_e_y":{"label":"The R-ONE family: the 15 in's thin slot row e y","kind":"length","measurements":[{"id":"family","value":-0.635,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.thin_slot_row_e_y}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"qd_socket_d":{"label":"The R-ONE family: the 15 in's qd socket d","kind":"length","measurements":[{"id":"family","value":0.37,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.qd_socket_d}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"reach_inside":{"label":"The room inside its side faces before the barrel, at the M-LOK slots (what an accessory's nuts may take)","kind":"length","measurements":[],"note":"Not read: as on the 15 in, it depends on the barrel under it."}}},{"subject":"aero-r-one-15-handguard","title":"Aero Precision AR15 15 in R-ONE M-LOK handguard (APRA500705A)","dimensions":{"weight":{"label":"Weight (the handguard; its barrel nut and screws are 1.9 oz more by the R-ONE's own page, 4.72 by this one)","kind":"mass","measurements":[{"id":"aero","value":9.07,"unit":"oz","pm":0.01,"stated":"Weight(s) 9.07 oz","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, AR15 15\" R-ONE M-LOK Handguard - Anodized Black (APRA500705A), Specifications","url":"https://www.aeroprecisionusa.com/ar15-15-atlas-r-one-m-lok-handguard-anodized-black","retrieved":"2026-10-02","via":"harvest"}},{"id":"aero-parent","value":9.07,"unit":"oz","pm":0.01,"stated":"15\" - 9.07 oz","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, AR15 R-ONE M-LOK Handguard (the configurable page), M-LOK Handguard Weights","url":"https://www.aeroprecisionusa.com/ar15-r-one-mlok-handguard","retrieved":"2026-10-02","via":"harvest"}},{"id":"wing-tactical","value":8.96,"unit":"oz","pm":0.005,"stated":"Weight: 15-Inch: 8.96 oz. Mounting Hardware: 4.72 oz.","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Aero Precision ATLAS R-ONE M-LOK Handguard (one page for the 7.3, 9.3, 12.7 and 15 in lengths), Specifications","url":"https://www.wingtactical.com/firearm-parts/ar-15/handguards-rails/rail-systems/aero-precision-atlas-r-one-m-lok-handguard/","retrieved":"2026-10-05","via":"harvest"},"note":"A seller's table, 0.11 oz under the maker's two pages; its hardware figure is this length's page's."}],"adopt":{"from":"aero","reason":"This length's own page; the R-ONE's page lists the same figure for 15 in. A seller's table (Wing Tactical) has 8.96."},"note":"The mounting hardware isn't counted here, and Aero's two pages disagree on it: the R-ONE's own page says \"Mounting Hardware Weight: 1.9 oz (same across all R-ONE Handguard options)\", this length's page lists 4.72 oz \"same across all ATLAS Handguard options\" (the discovery report). Neither is in the build's weight yet."},"length":{"label":"Length (the receiver's face to the end of the last rail slot)","kind":"length","measurements":[{"id":"aero","value":15,"unit":"in","pm":0.05,"stated":"Handguard Length 15\"","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, AR15 15\" R-ONE M-LOK Handguard - Anodized Black (APRA500705A), Specifications","url":"https://www.aeroprecisionusa.com/ar15-15-atlas-r-one-m-lok-handguard-anodized-black","retrieved":"2026-10-02","via":"harvest"}},{"id":"wing-tactical","value":14.94,"unit":"in","pm":0.005,"stated":"Actual Length (When Installed): 15-Inch: 14.94\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Aero Precision ATLAS R-ONE M-LOK Handguard (one page for the 7.3, 9.3, 12.7 and 15 in lengths), Specifications","url":"https://www.wingtactical.com/firearm-parts/ar-15/handguards-rails/rail-systems/aero-precision-atlas-r-one-m-lok-handguard/","retrieved":"2026-10-05","via":"harvest"},"note":"A seller's table; it doesn't say between what its installed length is taken."}],"adopt":{"from":"aero","reason":"The maker's, with its own rule for what the length spans (the receiver's face to the end of the last rail slot), which the outline is placed by. The seller's 14.94 when installed is 0.06 under it and doesn't say what it spans."},"note":"Aero says what its lengths are between: \"Aero Precision rail lengths measure from end to end. This is the point of contact at the receiver to the end of the last picatinny slot at the muzzle.\""},"width":{"label":"Width across its side faces at their lower edges, where it is widest (the maker's \"outside diameter\")","kind":"length","measurements":[{"id":"aero","value":1.5,"unit":"in","pm":0.05,"stated":"1.5\" Outside diameter","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, AR15 15\" R-ONE M-LOK Handguard - Anodized Black (APRA500705A), Features","url":"https://www.aeroprecisionusa.com/ar15-15-atlas-r-one-m-lok-handguard-anodized-black","retrieved":"2026-10-02","via":"harvest"}},{"id":"wing-tactical","value":1.51,"unit":"in","pm":0.005,"stated":"Outside Diameter: Height: 1.95\" Width: 1.51\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Aero Precision ATLAS R-ONE M-LOK Handguard (one page for the 7.3, 9.3, 12.7 and 15 in lengths), Specifications","url":"https://www.wingtactical.com/firearm-parts/ar-15/handguards-rails/rail-systems/aero-precision-atlas-r-one-m-lok-handguard/","retrieved":"2026-10-05","via":"harvest"},"note":"A seller's table gives the section's height and width apart: it isn't round. The views from its end have it flat-sided all round, faces at 3, 6 and 9 o'clock among them (2026-10-05: until then the model was a round tube of this diameter)."}],"adopt":{"from":"aero","reason":"The maker's own figure, to one place; the seller's 1.51 is inside it."}},"height":{"label":"Height (with the top rail)","kind":"length","measurements":[{"id":"photo","value":1.981,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard 588ce841463f (Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630)","scaleRef":"its top rail's 37 teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 23.548 px a tooth, 59.77 px/in","method":"the traced outline's height between 4 in and its front end (the body's): 118.4 px","via":"harvest"}},{"id":"wing-tactical","value":1.95,"unit":"in","pm":0.005,"stated":"Outside Diameter: Height: 1.95\" Width: 1.51\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Aero Precision ATLAS R-ONE M-LOK Handguard (one page for the 7.3, 9.3, 12.7 and 15 in lengths), Specifications","url":"https://www.wingtactical.com/firearm-parts/ar-15/handguards-rails/rail-systems/aero-precision-atlas-r-one-m-lok-handguard/","retrieved":"2026-10-05","via":"harvest"}},{"id":"rows","value":1.96,"unit":"in","pm":0.017,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard 588ce841463f and 484919052dbe (Aero's gallery: the R-ONE 15 in handguard from its left and from its right, each 1000 x 630)","scaleRef":"each view's own top rail, its teeth's period by autocorrelation over 30 of them against the Picatinny pitch (std.picatinny.slot_pitch): 23.60 px a tooth, 59.94 px/in in both; heights from the teeth's tops","method":"the tube's rows, away from the clamp: the teeth's tops at row 245 (244 in the right view), the bottom's last dark row 362 (361): 117.5 rows, a row either way","via":"harvest"}}],"adopt":{"from":"wing-tactical","reason":"A seller's table of the maker's sizes, to two places; the side views' rows read 1.96 ± 0.017 at the rail's scale. The traced outline stands 1.98 along its body: inside what a 1000 px photo carries, and kept as read."},"note":"The body's, its rail's top to its bottom flat; the clamp's end, with its anti-rotation tab, reaches 2.14. With the rail level with the receiver's (rail_top_above_bore, 1.2125), 1.95 puts the bottom flat 0.7375 below the bore, and half the width is 0.75: the body is centred on the bore, as high below it as it is wide to each side."},"overall_length":{"label":"Overall length, end to end","kind":"length","measurements":[{"id":"photo","value":15.36,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard 588ce841463f (Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630)","scaleRef":"its top rail's 37 teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 23.548 px a tooth, 59.77 px/in","method":"the silhouette end to end, 918 px","via":"harvest"}}],"note":"Aero's 15 in runs from the receiver to the end of the last rail slot; the handguard goes on past it, and its clamp's end overlaps the receiver's threads."},"mlok_slot0_from_rear":{"label":"The rearmost M-LOK slot's centre on its sides, ahead of the handguard's rear end (its outline's x = 0)","kind":"length","measurements":[{"id":"photo","value":4.897,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard 588ce841463f (Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630)","scaleRef":"its top rail's 37 teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 23.548 px a tooth, 59.77 px/in","method":"the seven long slots' centres along their row (px 101 to 668, mirrored), fitted to the M-LOK pitch (std.mlok.slot_pitch): they land on it to 0.4%; read from the outline's rear end (it was written as 4.452 ahead of the receiver's face with the rear end taken at -0.445)","via":"harvest"}}]},"mlok_slot0_x":{"label":"The rearmost M-LOK slot's centre on its sides, ahead of the receiver's face","kind":"length","measurements":[{"id":"derived","value":4.134,"unit":"in","source":{"type":"derived","expr":"{.rear_x} + {.mlok_slot0_from_rear}","via":"harvest"}}],"note":"Seven slots on each side at 3 and 9 o'clock, on the bore's level (the row's centre reads 0.03 above it). The thin slots above and below them, and the short one and the QD socket behind them, aren't M-LOK."},"mlok_slots":{"label":"How many M-LOK slots on each side","kind":"count","measurements":[{"id":"photo","value":7,"unit":"count","source":{"type":"photo","photo":"references/aero-r-one-15-handguard 588ce841463f (Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630)","scaleRef":"its top rail's 37 teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 23.548 px a tooth, 59.77 px/in","method":"counted","via":"harvest"}}]},"rail_top_above_bore":{"label":"Its rail's top above the bore axis","kind":"length","measurements":[{"id":"level","value":1.2125,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.rail_top_above_pin} - {aero-m4e1-threaded-upper.bore_axis_above_pin}","via":"harvest"}}],"note":"Level with the receiver's rail: Aero's page for the M4E1 Threaded upper says its picatinny profile \"blends seamlessly with our R-ONE, S-ONE and Enhanced Handguards\". So the receiver's rail top above the pin line less the bore's height above it."},"inside_diameter":{"label":"Inside width (the maker's \"inside diameter\")","kind":"length","measurements":[{"id":"aero","value":1.3,"unit":"in","pm":0.05,"stated":"1.3\" Inside diameter","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, AR15 15\" R-ONE M-LOK Handguard - Anodized Black (APRA500705A), Features","url":"https://www.aeroprecisionusa.com/ar15-15-atlas-r-one-m-lok-handguard-anodized-black","retrieved":"2026-10-02","via":"harvest"}},{"id":"wing-tactical","value":1.3,"unit":"in","pm":0.05,"stated":"Inside Diameter: Height: 1.65\" Width: 1.3\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Aero Precision ATLAS R-ONE M-LOK Handguard (one page for the 7.3, 9.3, 12.7 and 15 in lengths), Specifications","url":"https://www.wingtactical.com/firearm-parts/ar-15/handguards-rails/rail-systems/aero-precision-atlas-r-one-m-lok-handguard/","retrieved":"2026-10-05","via":"harvest"}}],"adopt":{"from":"aero","reason":"The maker's own figure; the seller's table has the same."}},"inside_height":{"label":"Inside height (its floor to the underside of its rail)","kind":"length","measurements":[{"id":"wing-tactical","value":1.65,"unit":"in","pm":0.005,"stated":"Inside Diameter: Height: 1.65\" Width: 1.3\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Aero Precision ATLAS R-ONE M-LOK Handguard (one page for the 7.3, 9.3, 12.7 and 15 in lengths), Specifications","url":"https://www.wingtactical.com/firearm-parts/ar-15/handguards-rails/rail-systems/aero-precision-atlas-r-one-m-lok-handguard/","retrieved":"2026-10-05","via":"harvest"}}],"note":"0.35 more than its width: the room over the barrel, where the gas block and tube go. With walls of ({.width} - {.inside_diameter}) / 2 its floor is 0.64 below the bore and its top 1.01 above it, 0.2 under the rail's top: up inside the rail's neck, a channel the rail's windows open into. The view from its muzzle end (abbec08229c1) has that channel's top an arch, 0.19 below the rail's top (row 757 where the top is 706.4 and an inch down is 267.8 rows): 1.66 above a floor a wall thick."},"side_flat_top_below_rail_top":{"label":"Its side faces' upper edge, below the rail's top","kind":"length","measurements":[{"id":"sides","value":0.88,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard 588ce841463f and 484919052dbe (Aero's gallery: the R-ONE 15 in handguard from its left and from its right, each 1000 x 630)","scaleRef":"each view's own top rail, its teeth's period by autocorrelation over 30 of them against the Picatinny pitch (std.picatinny.slot_pitch): 23.60 px a tooth, 59.94 px/in in both; heights from the teeth's tops","method":"the tone down the solid bars between the slots (35 and 32 columns with no opening from 0.8 to 1.05 in down): a step from the slanted face's tone to the flat's, 96 to 59 at 0.868 in the left view and 96 to 58 at 0.891 in the right, a bright line along the edge just above it (.cache/r-one/side_levels.py)","via":"harvest"},"note":"0.33 above the bore."},{"id":"end","value":0.883,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard abbec08229c1 (Wing Tactical's gallery: an R-ONE from its muzzle end, looking back along its rail, 1280 x 1280; the photo the user sent on 2026-10-05, 8dd2b17f2f5f, is a copy of it)","scaleRef":"the same end face in the same photo: across, its width at the side faces' lower edges, where it is widest (aero-r-one-15-handguard.width: 427.1 px, 284.8 px/in); down, its rail's top to its bottom flat (aero-r-one-15-handguard.height: rows 706.4 to 1228.6, 267.8 px/in: it is seen from 20 degrees above). One scale down the face serves","method":"each stretch of the end face's outline as a straight line through its own edge crossings, row by row or column by column (rms 0.1 to 0.5 px), and the corners where the lines meet, left and right; the face is rolled one degree in the photo, and each figure is the mean of its two sides (.cache/r-one/end_section.py); where the upper face's outer edge on the end face meets the side face's (0.872 left, 0.894 right)","via":"harvest"}}],"adopt":{"from":"sides","reason":"Aero's own views of the 15 in, straight from the side, where the step is plain in both. The view from the end, scaled down its face by the published height, has the same edge at 0.883."}},"side_flat_bottom_below_rail_top":{"label":"Its side faces' lower edge, below the rail's top","kind":"length","measurements":[{"id":"sides","value":1.49,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard 588ce841463f and 484919052dbe (Aero's gallery: the R-ONE 15 in handguard from its left and from its right, each 1000 x 630)","scaleRef":"each view's own top rail, its teeth's period by autocorrelation over 30 of them against the Picatinny pitch (std.picatinny.slot_pitch): 23.60 px a tooth, 59.94 px/in in both; heights from the teeth's tops","method":"the same bars' tone further down: a faint step, 56 to 52 at 1.487 in the left view and 60 to 52 at 1.498 in the right (.cache/r-one/side_levels.py)","via":"harvest"},"note":"The step on the side views is faint."},{"id":"end","value":1.502,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard abbec08229c1 (Wing Tactical's gallery: an R-ONE from its muzzle end, looking back along its rail, 1280 x 1280; the photo the user sent on 2026-10-05, 8dd2b17f2f5f, is a copy of it)","scaleRef":"the same end face in the same photo: across, its width at the side faces' lower edges, where it is widest (aero-r-one-15-handguard.width: 427.1 px, 284.8 px/in); down, its rail's top to its bottom flat (aero-r-one-15-handguard.height: rows 706.4 to 1228.6, 267.8 px/in: it is seen from 20 degrees above). One scale down the face serves","method":"each stretch of the end face's outline as a straight line through its own edge crossings, row by row or column by column (rms 0.1 to 0.5 px), and the corners where the lines meet, left and right; the face is rolled one degree in the photo, and each figure is the mean of its two sides (.cache/r-one/end_section.py); where the side face's edge meets the steep lower face's (1.488 left, 1.516 right)","via":"harvest"}}],"adopt":{"from":"end","reason":"The corner itself, where two fitted edges of the silhouette meet; on the side views it is a step of four tones in a bar a few pixels wide, read at 1.49 ± 0.03. 0.29 below the bore."}},"side_top_width":{"label":"Width across its side faces at their upper edges","kind":"length","measurements":[{"id":"end","value":1.455,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard abbec08229c1 (Wing Tactical's gallery: an R-ONE from its muzzle end, looking back along its rail, 1280 x 1280; the photo the user sent on 2026-10-05, 8dd2b17f2f5f, is a copy of it)","scaleRef":"the same end face in the same photo: across, its width at the side faces' lower edges, where it is widest (aero-r-one-15-handguard.width: 427.1 px, 284.8 px/in); down, its rail's top to its bottom flat (aero-r-one-15-handguard.height: rows 706.4 to 1228.6, 267.8 px/in: it is seen from 20 degrees above). One scale down the face serves: the side faces' two edges land at 0.883 and 1.502 below the top where Aero's side views have them at 0.88 and 1.49","method":"each stretch of the end face's outline as a straight line through its own edge crossings, row by row or column by column (rms 0.1 to 0.5 px), and the corners where the lines meet, left and right; the face is rolled one degree in the photo, and each figure is the mean of its two sides (.cache/r-one/end_section.py); between the two corners where the upper faces' outer edges meet the side faces': 414.4 px where the lower corners are 427.1 apart, the left edge running out 0.058 px a row downward and the right 0.019 on a face rolled 0.015 to 0.018 (its bottom flat's slope, its centre line's)","via":"harvest"}}],"note":"Less than across their lower edges (the published width): each side face leans in 2.1 degrees toward its top. Not the photo's perspective: down the same face its heights keep one scale (the rail's top, these two edges and the bottom land within a pixel of a line), and its rail's head reads 0.814 across at the scale its width sets where the standard has 0.835. Two more views agree in direction: against the upright sides of the rail's neck, the far side face's edge runs out 0.02 px a row downward in Brownells' view of a shorter one from ahead (96680cef7d9e: 1.7 degrees) and 0.07 in Wing Tactical's (30f5919d7a4e)."},"bottom_flat_width":{"label":"Its bottom flat (6 o'clock), across","kind":"length","measurements":[{"id":"end","value":0.609,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard abbec08229c1 (Wing Tactical's gallery: an R-ONE from its muzzle end, looking back along its rail, 1280 x 1280; the photo the user sent on 2026-10-05, 8dd2b17f2f5f, is a copy of it)","scaleRef":"the same end face in the same photo: across, its width at the side faces' lower edges, where it is widest (aero-r-one-15-handguard.width: 427.1 px, 284.8 px/in); down, its rail's top to its bottom flat (aero-r-one-15-handguard.height: rows 706.4 to 1228.6, 267.8 px/in: it is seen from 20 degrees above). One scale down the face serves: the side faces' two edges land at 0.883 and 1.502 below the top where Aero's side views have them at 0.88 and 1.49","method":"each stretch of the end face's outline as a straight line through its own edge crossings, row by row or column by column (rms 0.1 to 0.5 px), and the corners where the lines meet, left and right; the face is rolled one degree in the photo, and each figure is the mean of its two sides (.cache/r-one/end_section.py); between the two corners where the bottom's line (the lowest dark row, column by column: rms 0.27 px over 150 columns) meets the shallow lower faces': 173.5 px","via":"harvest"},"note":"First read as 0.618 between the ends of one straight edge a side, which the outline there isn't (2026-10-05)."}]},"lower_edge_width":{"label":"Width across the edges between its two lower faces (each side: the steep one under the side face, the shallow one into the bottom flat)","kind":"length","measurements":[{"id":"end","value":1.133,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard abbec08229c1 (Wing Tactical's gallery: an R-ONE from its muzzle end, looking back along its rail, 1280 x 1280; the photo the user sent on 2026-10-05, 8dd2b17f2f5f, is a copy of it)","scaleRef":"the same end face in the same photo: across, its width at the side faces' lower edges, where it is widest (aero-r-one-15-handguard.width: 427.1 px, 284.8 px/in); down, its rail's top to its bottom flat (aero-r-one-15-handguard.height: rows 706.4 to 1228.6, 267.8 px/in: it is seen from 20 degrees above). One scale down the face serves: the side faces' two edges land at 0.883 and 1.502 below the top where Aero's side views have them at 0.88 and 1.49","method":"each stretch of the end face's outline as a straight line through its own edge crossings, row by row or column by column (rms 0.1 to 0.5 px), and the corners where the lines meet, left and right; the face is rolled one degree in the photo, and each figure is the mean of its two sides (.cache/r-one/end_section.py); between the two corners where the steep lower faces' edges meet the shallow ones': 322.6 px","via":"harvest"}},{"id":"wing-three-quarter","value":1.144,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard 30f5919d7a4e (Wing Tactical's gallery: an R-ONE from ahead and above on its right, 1280 x 1280; the photo the user sent on 2026-10-05 with \"each of the m-lok slots is on its own face on the bottom half\", a3e4bd3beabb, is a copy of it)","scaleRef":"the far side of the same end face against the white: its side face's two edges and its bottom flat's corner, each where two fitted stretches of the silhouette meet, set to this ledger's figures for them (side_flat_top_below_rail_top, side_flat_bottom_below_rail_top, side_top_width, width, bottom_flat_width, height), which fixes how the end face lies in the picture","method":"the silhouette's edge row by row (where the tone crosses half way), a straight line through each stretch (the upper face one stretch; under the side face two, turning 0.61 px a row to 1.02, then the bottom flat), and the corner between the two lower stretches placed among the three known ones (.cache/r-one/edges34.py)","via":"harvest"}},{"id":"brownells-three-quarter","value":1.117,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard 96680cef7d9e (Brownells' gallery, item 430103930: a short R-ONE in OD green from ahead on its right, 1200 x 1200)","scaleRef":"the far side of the same end face against the white: its side face's two edges and its bottom flat's corner, each where two fitted stretches of the silhouette meet, set to this ledger's figures for them (side_flat_top_below_rail_top, side_flat_bottom_below_rail_top, side_top_width, width, bottom_flat_width, height), which fixes how the end face lies in the picture","method":"the silhouette's edge row by row (where the tone crosses half way), a straight line through each stretch (the upper face one stretch; under the side face two, turning 0.37 px a row to 0.60, then the bottom flat), and the corner between the two lower stretches placed among the three known ones (.cache/r-one/edges34.py)","via":"harvest"},"note":"Another length of the R-ONE, the same section."}],"adopt":{"from":"end","reason":"The view square to the section, both sides in it, scaled across by the published width. Two three-quarter views, one of them of another length, put the same edge within 0.016 of it."}},"lower_edge_below_rail_top":{"label":"The edges between its two lower faces, below the rail's top","kind":"length","measurements":[{"id":"end","value":1.759,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard abbec08229c1 (Wing Tactical's gallery: an R-ONE from its muzzle end, looking back along its rail, 1280 x 1280; the photo the user sent on 2026-10-05, 8dd2b17f2f5f, is a copy of it)","scaleRef":"the same end face in the same photo: across, its width at the side faces' lower edges, where it is widest (aero-r-one-15-handguard.width: 427.1 px, 284.8 px/in); down, its rail's top to its bottom flat (aero-r-one-15-handguard.height: rows 706.4 to 1228.6, 267.8 px/in: it is seen from 20 degrees above). One scale down the face serves: the side faces' two edges land at 0.883 and 1.502 below the top where Aero's side views have them at 0.88 and 1.49","method":"each stretch of the end face's outline as a straight line through its own edge crossings, row by row or column by column (rms 0.1 to 0.5 px), and the corners where the lines meet, left and right; the face is rolled one degree in the photo, and each figure is the mean of its two sides (.cache/r-one/end_section.py); the corners where the steep lower faces' edges meet the shallow ones' (1.749 left, 1.768 right)","via":"harvest"},"note":"0.55 below the bore. The steep face then drops 0.257 over 0.184 (54 degrees from level) and the shallow one 0.191 over 0.262 (36): 18 degrees between them, and each as long across as the other (0.32), a row of slots down the middle of each."},{"id":"wing-three-quarter","value":1.76,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard 30f5919d7a4e (Wing Tactical's gallery: an R-ONE from ahead and above on its right, 1280 x 1280; the photo the user sent on 2026-10-05 with \"each of the m-lok slots is on its own face on the bottom half\", a3e4bd3beabb, is a copy of it)","scaleRef":"the far side of the same end face against the white: its side face's two edges and its bottom flat's corner, each where two fitted stretches of the silhouette meet, set to this ledger's figures for them (side_flat_top_below_rail_top, side_flat_bottom_below_rail_top, side_top_width, width, bottom_flat_width, height), which fixes how the end face lies in the picture","method":"the silhouette's edge row by row (where the tone crosses half way), a straight line through each stretch (the upper face one stretch; under the side face two, turning 0.61 px a row to 1.02, then the bottom flat), and the corner between the two lower stretches placed among the three known ones (.cache/r-one/edges34.py)","via":"harvest"}},{"id":"brownells-three-quarter","value":1.775,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard 96680cef7d9e (Brownells' gallery, item 430103930: a short R-ONE in OD green from ahead on its right, 1200 x 1200)","scaleRef":"the far side of the same end face against the white: its side face's two edges and its bottom flat's corner, each where two fitted stretches of the silhouette meet, set to this ledger's figures for them (side_flat_top_below_rail_top, side_flat_bottom_below_rail_top, side_top_width, width, bottom_flat_width, height), which fixes how the end face lies in the picture","method":"the silhouette's edge row by row (where the tone crosses half way), a straight line through each stretch (the upper face one stretch; under the side face two, turning 0.37 px a row to 0.60, then the bottom flat), and the corner between the two lower stretches placed among the three known ones (.cache/r-one/edges34.py)","via":"harvest"},"note":"Another length of the R-ONE, the same section."}],"adopt":{"from":"end","reason":"The view square to the section, both sides in it, scaled down by the published height. The two three-quarter views have it at 1.76 and 1.775."}},"rail_neck_width":{"label":"The neck its rail stands on (under the rail's head, above the two upper faces), across","kind":"length","measurements":[{"id":"end","value":0.62,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard abbec08229c1 (Wing Tactical's gallery: an R-ONE from its muzzle end, looking back along its rail, 1280 x 1280; the photo the user sent on 2026-10-05, 8dd2b17f2f5f, is a copy of it)","scaleRef":"the same end face in the same photo: across, its width at the side faces' lower edges, where it is widest (aero-r-one-15-handguard.width: 427.1 px, 284.8 px/in); down, its rail's top to its bottom flat (aero-r-one-15-handguard.height: rows 706.4 to 1228.6, 267.8 px/in: it is seen from 20 degrees above). One scale down the face serves: the side faces' two edges land at 0.883 and 1.502 below the top where Aero's side views have them at 0.88 and 1.49; and the rail's own head beside it, 231.8 px across its widest where the standard has 0.835 in (277.6 px/in: its corners are rounded)","method":"the end face's own edges under the head, where its dark gives way to the lit lugs behind it, on the rows from 770 to 790: 558.7 and 732.8, upright within 0.3 px, 174.1 px apart: 0.611 at the body's scale and 0.627 at the head's (.cache/r-one/end_section.py, end_head.py)","via":"harvest"},"note":"The far side's silhouette in the two three-quarter views steps in under the head by 0.071 and 0.076 where this has 0.10: their scale across is the bottom flat's corner's, a long way from the head."}],"note":"Under the head's lower 45 degree faces the end face runs straight down, upright, before the two upper faces leave it: a neck. With the standard's head (std.picatinny.top_width, lower_gauge_below_top) those faces come in to this width 0.22 below the rail's top, where the photo has the neck begin (row 765: 0.219). First read as the rail's foot, 0.72 across at 0.14 down: a place on the head's underside, and the upper faces were drawn from there, the rail a neck short (2026-10-05, the user: \"Your rail height doesn't look quite right in those new models\")."},"rail_neck_foot_below_rail_top":{"label":"The neck's foot, where the two upper faces leave it, below the rail's top","kind":"length","measurements":[{"id":"end","value":0.377,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard abbec08229c1 (Wing Tactical's gallery: an R-ONE from its muzzle end, looking back along its rail, 1280 x 1280; the photo the user sent on 2026-10-05, 8dd2b17f2f5f, is a copy of it)","scaleRef":"the same end face in the same photo: across, its width at the side faces' lower edges, where it is widest (aero-r-one-15-handguard.width: 427.1 px, 284.8 px/in); down, its rail's top to its bottom flat (aero-r-one-15-handguard.height: rows 706.4 to 1228.6, 267.8 px/in: it is seen from 20 degrees above). One scale down the face serves: the side faces' two edges land at 0.883 and 1.502 below the top where Aero's side views have them at 0.88 and 1.49","method":"where the line through each upper face's outer edge on the end face (rms 0.3 to 0.5 px over 40 rows) meets the neck's upright edge: rows 808.1 and 806.4 (0.380 left, 0.374 right) (.cache/r-one/end_section.py)","via":"harvest"},"note":"The corner is rounded: the edge leaves the neck's line from 0.33 down, and Aero's side views have the upper face's lit top begin at 0.33 and 0.34 down the bars between its slots, under a grey band from 0.20 that is the neck's side. The upper face then drops 0.50 over 0.42 (50 degrees from level) to the side face's upper edge, 0.65 across: twice a lower face, its two rows of slots a lower face's width apart."}]},"rail_centre_gap":{"label":"Its rail's middle, between the two ears of a lug (the windows' width)","kind":"length","measurements":[{"id":"end","value":0.365,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard abbec08229c1 (Wing Tactical's gallery: an R-ONE from its muzzle end, looking back along its rail, 1280 x 1280; the photo the user sent on 2026-10-05, 8dd2b17f2f5f, is a copy of it)","scaleRef":"the same lugs' lit tops, edge to edge 186 to 190 px: the rail's top flat between its 45 degree faces, 0.656 in by the standard (std.picatinny.bevel_width less twice the upper gauge line's depth); the dark band outside each end is 25 px, the bevel's 0.09","method":"across the rows through two lugs that have no middle (540 and 564, 660): each ear's top 39 to 41 px, the dark between them 100 to 106 (.cache/r-one/rail_measure.py)","via":"harvest"},"note":"Each ear's top is then 0.14 across. The lugs with a middle are lit the same width edge to edge."}]},"rail_window_length":{"label":"A window along its rail (the middle, open between two bridges)","kind":"length","measurements":[{"id":"end","value":0.54,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard abbec08229c1 (Wing Tactical's gallery: an R-ONE from its muzzle end, looking back along its rail, 1280 x 1280; the photo the user sent on 2026-10-05, 8dd2b17f2f5f, is a copy of it)","scaleRef":"the lugs' own pitch along the same stretch (std.picatinny.slot_pitch): the ears' tops come every 27 to 32 px down the columns through them, the bridges' every 52 to 62 down the middle: every other lug","method":"down the middle column, the dark between two bridges' lit tops: 38 to 41 px of the 46 between them, with the bridge's own top 10 to 14 px as the ears' are (12 to 13): a lug's length. So a window is two pitches less a lug, less 0.06 for its two ends (.cache/r-one/rail_cols.py)","via":"harvest"},"note":"Brownells' view of a shorter R-ONE from above (d1035d735f06) has the same windows, rounded at their ends, about a pitch and a half long; and two round holes instead over its barrel nut, which this length's photos don't show from above."}]},"rail_bridge_recess":{"label":"A bridge's top below the ears' (the lugs that have a middle)","kind":"length","measurements":[{"id":"end","value":0.03,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard abbec08229c1 (Wing Tactical's gallery: an R-ONE from its muzzle end, looking back along its rail, 1280 x 1280; the photo the user sent on 2026-10-05, 8dd2b17f2f5f, is a copy of it)","scaleRef":"heights seen from 15 degrees above the rail's plane (a pitch along the rail is 29 px where the rail's width gives 287 px/in): 277 px for an inch of height","method":"each bridge's lit top stands 7 to 10 px lower in the picture than its own lug's ears (461-470 against 453-462, 513-523 against 505-516, 570-581 against 562-574, 631-644 against 623-634): taken as lower, not further forward (.cache/r-one/rail_cols.py)","via":"harvest"},"note":"It could as well be a bridge 0.03 to 0.1 in nearer the muzzle than its ears: one view can't tell height from place. Drawn as a step down."}]},"rear_x":{"label":"The handguard's rear end (its two side tabs' ends) against the receiver's front face (negative: behind it)","kind":"length","measurements":[{"id":"derived","value":-0.763,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"0in - {std.ar15.upper_barrel_thread_length} - ({.rail_front_from_rear} - {.length})","via":"harvest"},"note":"Aero: rail lengths \"measure from end to end. This is the point of contact at the receiver to the end of the last picatinny slot at the muzzle\": 15 in back from the outline's rail end (15.318 from its rear end) is 0.318 ahead of the tabs' ends, where the outline's full section starts (its top steps up at 0.30, its bottom down at 0.35)."},{"id":"kit-right","value":-0.778,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/aero-m4e1-complete-upper-16-mid-r-one-15 0a6c8a661544 (Aero's gallery for the complete upper APAR700705M7, photo 1, right side; its file is named for the 223 Wylde upper)","scaleRef":"the receiver's lug holes (px 78.5, 314.4): 37.0 px/in; the handguard's rail teeth, 14.43 px a tooth, along it","method":"the handguard's first full tooth at px 334.0, 0.535 ahead of the pivot hole; its outline puts that tooth 0.6515 ahead of its rear end: the rear end 6.258 ahead of the takedown pin, against the receiver's front face at 7.036 (.cache/research/aero-upper/kit_teeth.py)","via":"harvest"}},{"id":"kit-left","value":-0.775,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/aero-m4e1-complete-upper-16-mid-r-one-15 da42ceb722d9 (Aero's gallery for the complete upper APAR700705M7, photo 2, left side)","scaleRef":"the receiver's lug holes (px 692.5, 928.2): 36.97 px/in; the rail teeth 14.655 px","method":"the first full tooth at px 672.5, 0.537 ahead of the pivot hole: the rear end 6.261 ahead of the takedown pin; its own visible edge at px 696 reads 6.28","via":"harvest"}},{"id":"shoulder","value":-0.445,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"0in - {std.ar15.upper_barrel_thread_length}","via":"harvest"},"note":"The contact face, not the outline's rear end: what the ledger had until 2026-10-03."}],"adopt":{"from":"derived","reason":"Aero's own rule for its length, on its own outline; both photos of the complete upper agree with it within 0.015 in."},"note":"The outline's x = 0 is the ends of two tabs that reach back along the receiver's front ring; the face that meets the receiver (Aero's \"point of contact at the receiver\") is 0.318 ahead of them, at the receiver's front shoulder, where the barrel-nut thread begins. Until 2026-10-03 the tabs' ends were taken as that face, which put the handguard 0.32 in too far forward: it ran past the barrel's shoulder over the muzzle device."},"reach_inside":{"label":"The room inside its side faces, from the face in to the barrel (what an M-LOK accessory's nuts may take)","kind":"length","measurements":[],"note":"Not sourced: the barrel under it is another part, and its diameter under the handguard isn't on file (its traced photo shows it ahead of the handguard only)."},"rail_front_from_rear":{"label":"Its rail's front end (the end of the last slot) ahead of the outline's rear end","kind":"length","measurements":[{"id":"photo","value":15.318,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard 588ce841463f (Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630)","scaleRef":"its top rail's 37 teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 23.548 px a tooth, 59.77 px/in","method":"the outline's top flat ahead of the last slot, to x 15.318","via":"harvest"}}]},"rail_slot0_from_rear":{"label":"Its rail's rearmost slot (its centre) ahead of the outline's rear end","kind":"length","measurements":[{"id":"photo","value":0.855,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard 588ce841463f (Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630)","scaleRef":"the rail's own slots beside it: its last eight pitches at the standard's 0.394 in (std.picatinny.slot_pitch) are 59.32 px/in there (60.49 at the muzzle end: the lens stood nearer the middle)","method":"the gaps between the teeth in the rows of the tooth tops (245 to 248), each edge at the 50% level: the rearmost gap's centre is 50.7 px ahead of the outline's rear end (.cache/batch123/rone/slots.py). A slot seen obliquely narrows about its own middle (13 px wide near the lens's axis, 7 at this end), so its centre holds","via":"harvest"}}],"note":"With rear_x it puts that slot 7.13 in ahead of the takedown pin on Aero's M4E1 Threaded upper: 2.15 pitches ahead of that receiver's last slot (6.285), each from its own photo. Two whole pitches is within what the two readings and the handguard's place carry between them (about 0.05 in), so the rails may well share one grid; nothing is assumed either way. 2026-10-12, when the model's slots were cut on this grid (they had been the outline's own): the traced outline has its first gap 0.001 in from this figure and its last 0.005 from where 36 pitches on put it, and between them its gaps bow up to 0.044 in behind the grid (slots 12 to 17), because the outline has one scale end to end over a photo whose scale rises 2% from the rear to the muzzle; a rail is machined to an even pitch, so the grid is the rail and the bow the photo. The ± covers the gap's centre (half a pixel, 0.008) and the scale beside it. It doesn't cover the outline's rear end, which this is counted from: that is the near tab's end, 0.6 in nearer the lens than the rail's middle and 10 in off its axis, and reads behind where the tab ends by that over the lens's distance (about 0.1 in if the lens was 65 in off, as the slots' narrowing has it). Where the grid stands on a rifle doesn't rest on that end: rear_x is 15 in back from the rail's front end less the same outline's length, so the first slot stands (rail_front_from_rear − this) behind the rail's front end, both read on the rail."},"rail_slots":{"label":"Slots in its top rail","kind":"count","measurements":[{"id":"photo","value":37,"unit":"count","source":{"type":"photo","photo":"references/aero-r-one-15-handguard 588ce841463f (Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630)","scaleRef":"none: a count","method":"the gaps between the teeth along the whole rail, each at least 7 px wide and 22.7 to 24.8 px from the next: 37","via":"harvest"}}]},"thin_slot_first_from_rear":{"label":"The thin slots' first centre ahead of the outline's rear end (all four rows)","kind":"length","measurements":[{"id":"photo","value":2.987,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard 588ce841463f (Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630)","scaleRef":"its top rail's 37 teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 23.548 px a tooth, 59.77 px/in","method":"the see-through slots' centres in the four rows fitted to one pitch (.cache/research/aero-upper/hg_holes.py)","via":"harvest"}}]},"thin_slot_pitch":{"label":"The thin slots' pitch along each row","kind":"length","measurements":[{"id":"photo","value":1.0685,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard 588ce841463f (Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630)","scaleRef":"its top rail's 37 teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 23.548 px a tooth, 59.77 px/in","method":"11 pitches over 11.753 in, the rows above and below the M-LOK row; the complete upper's photo 0a6c8a661544 reads 1.055","via":"harvest"}}]},"thin_slot_count":{"label":"Thin slots in each row","kind":"count","measurements":[{"id":"photo","value":12,"unit":"count","source":{"type":"photo","photo":"references/aero-r-one-15-handguard 588ce841463f (Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630)","scaleRef":"its top rail's 37 teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 23.548 px a tooth, 59.77 px/in","method":"counted in each of the four rows","via":"harvest"}}]},"thin_slot_length":{"label":"A thin slot's length (at least: what shows through both walls)","kind":"length","measurements":[{"id":"photo","value":0.954,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard 588ce841463f (Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630)","scaleRef":"its top rail's 37 teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 23.548 px a tooth, 59.77 px/in","method":"the longest see-through slot in the two inner rows, 57 px","via":"harvest"}}]},"thin_slot_width":{"label":"A thin slot's width, across the slanted face it is in","kind":"length","measurements":[{"id":"photo","value":0.12,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard 588ce841463f (Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630)","scaleRef":"its top rail's 37 teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 23.548 px a tooth, 59.77 px/in","method":"the widest see-through height in a row, the upper outer row's (0.61 to 0.73 above the bore); the others show 0.05 to 0.117","via":"harvest"}},{"id":"opening","value":0.22,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard 588ce841463f and 484919052dbe (Aero's gallery: the R-ONE 15 in handguard from its left and from its right, each 1000 x 630)","scaleRef":"each view's own top rail, its teeth's period by autocorrelation over 30 of them against the Picatinny pitch (std.picatinny.slot_pitch): 23.60 px a tooth, 59.94 px/in in both; heights from the teeth's tops","method":"the opening on the near wall: down the columns through the slots' middles the tone leaves the bars' over 0.17 to 0.19 in (the inner rows: 0.66 to 0.83 and 1.52 to 1.71 below the rail's top; the part that shows through both walls is the half of it nearer the side flat). Seen from the side on faces that stand 54 degrees from level (the steep lower one) and 50 (the upper), that is 0.23 and 0.22 across the face (.cache/r-one/side_slots.py)","via":"harvest"},"note":"One width is drawn for all four rows. Two thirds of the face it is in: the two lower faces are 0.32 across, the upper one 0.66 with two rows."}],"adopt":{"from":"opening","reason":"The opening itself. What shows through both walls (0.12) is less: the far wall and the floor stand behind the rest of it."}},"thin_slot_row_a_y":{"label":"The upper outer row of thin slots, its height above the bore","kind":"length","measurements":[{"id":"photo","value":0.66,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard 588ce841463f (Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630)","scaleRef":"its top rail's 37 teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 23.548 px a tooth, 59.77 px/in; the top at rail_top_above_bore","method":"the see-through slots' vertical centres (0.61 to 0.73)","via":"harvest"}},{"id":"opening","value":0.71,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard 588ce841463f and 484919052dbe (Aero's gallery: the R-ONE 15 in handguard from its left and from its right, each 1000 x 630)","scaleRef":"each view's own top rail, its teeth's period by autocorrelation over 30 of them against the Picatinny pitch (std.picatinny.slot_pitch): 23.60 px a tooth, 59.94 px/in in both; heights from the teeth's tops","method":"the middle of the opening on the near wall, 0.41 to 0.59 below the rail's top (0.384 to 0.59 in the left view, 0.434 to 0.59 in the right), with the rail's top at rail_top_above_bore (.cache/r-one/side_slots.py)","via":"harvest"}}],"adopt":{"from":"opening","reason":"Where the opening is on the face it is cut in, which the model cuts. The earlier reading is the middle of what shows through both walls, the opening's half nearer the side flat."}},"thin_slot_row_b_y":{"label":"The upper inner row of thin slots, its height above the bore","kind":"length","measurements":[{"id":"photo","value":0.443,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard 588ce841463f (Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630)","scaleRef":"its top rail's 37 teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 23.548 px a tooth, 59.77 px/in; the top at rail_top_above_bore","method":"the see-through slots' vertical centres (0.393 to 0.493)","via":"harvest"}},{"id":"opening","value":0.46,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard 588ce841463f and 484919052dbe (Aero's gallery: the R-ONE 15 in handguard from its left and from its right, each 1000 x 630)","scaleRef":"each view's own top rail, its teeth's period by autocorrelation over 30 of them against the Picatinny pitch (std.picatinny.slot_pitch): 23.60 px a tooth, 59.94 px/in in both; heights from the teeth's tops","method":"the middle of the opening on the near wall, 0.67 to 0.84 below the rail's top (0.66 to 0.835, 0.684 to 0.851), with the rail's top at rail_top_above_bore (.cache/r-one/side_slots.py)","via":"harvest"}}],"adopt":{"from":"opening","reason":"Where the opening is on the face it is cut in, which the model cuts. The earlier reading is the middle of what shows through both walls, the opening's half nearer the side flat."}},"thin_slot_row_d_y":{"label":"The lower inner row of thin slots, its height above the bore","kind":"length","measurements":[{"id":"photo","value":-0.385,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard 588ce841463f (Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630)","scaleRef":"its top rail's 37 teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 23.548 px a tooth, 59.77 px/in; the top at rail_top_above_bore","method":"the see-through slots' vertical centres (-0.444 to -0.327)","via":"harvest"}},{"id":"opening","value":-0.41,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard 588ce841463f and 484919052dbe (Aero's gallery: the R-ONE 15 in handguard from its left and from its right, each 1000 x 630)","scaleRef":"each view's own top rail, its teeth's period by autocorrelation over 30 of them against the Picatinny pitch (std.picatinny.slot_pitch): 23.60 px a tooth, 59.94 px/in in both; heights from the teeth's tops","method":"the middle of the opening on the near wall, 1.525 to 1.715 below the rail's top (1.518 to 1.71, 1.535 to 1.72), with the rail's top at rail_top_above_bore (.cache/r-one/side_slots.py)","via":"harvest"}}],"adopt":{"from":"opening","reason":"Where the opening is on the face it is cut in, which the model cuts. The earlier reading is the middle of what shows through both walls, the opening's half nearer the side flat."}},"thin_slot_row_e_y":{"label":"The lower outer row of thin slots, its height above the bore","kind":"length","measurements":[{"id":"photo","value":-0.6,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard 588ce841463f (Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630)","scaleRef":"its top rail's 37 teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 23.548 px a tooth, 59.77 px/in; the top at rail_top_above_bore","method":"the see-through slots' vertical centres (-0.628 to -0.578)","via":"harvest"}},{"id":"opening","value":-0.635,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard 588ce841463f and 484919052dbe (Aero's gallery: the R-ONE 15 in handguard from its left and from its right, each 1000 x 630)","scaleRef":"each view's own top rail, its teeth's period by autocorrelation over 30 of them against the Picatinny pitch (std.picatinny.slot_pitch): 23.60 px a tooth, 59.94 px/in in both; heights from the teeth's tops","method":"the opening on the near wall begins 1.78 below the rail's top (1.77, 1.785); below that the face is too dark to show its end. It is in the shallow lower face, which stands 36 degrees from level (lower_edge_width, lower_edge_below_rail_top): an opening of the other rows' width across that face (thin_slot_width) is 0.13 tall from the side, so its middle is 1.845 down, with the rail's top at rail_top_above_bore (.cache/r-one/side_slots.py)","via":"harvest"},"note":"First taken to end where row a's does, mirrored about the M-LOK row, on one lower face at 46 degrees: -0.66 (2026-10-05). The shallow face runs from 1.759 to 1.95 down: its middle is 0.642 below the bore, and what shows through both walls (the opening's upper part on a face this shallow, 1.785 to 1.835) is what an opening there would show."}],"adopt":{"from":"opening","reason":"Where the opening is on the face it is cut in, which the model cuts. The earlier reading is the middle of what shows through both walls, the opening's half nearer the side flat."}},"short_slot_rear_from_rear":{"label":"The short slot behind the M-LOK slots (in their row), its rear end ahead of the outline's rear end","kind":"length","measurements":[{"id":"photo","value":3.539,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard 588ce841463f (Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630)","scaleRef":"its top rail's 37 teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 23.548 px a tooth, 59.77 px/in","method":"the see-through slot from 3.539 to 3.856 (0.317 long), y -0.093 to 0.175: the M-LOK row's height","via":"harvest"}}]},"short_slot_length":{"label":"The short slot's length","kind":"length","measurements":[{"id":"photo","value":0.317,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard 588ce841463f (Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630)","scaleRef":"its top rail's 37 teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 23.548 px a tooth, 59.77 px/in","method":"as short_slot_rear_from_rear","via":"harvest"}}]},"qd_socket_from_rear":{"label":"The QD sling socket on each side (3 and 9 o'clock), its centre ahead of the outline's rear end","kind":"length","measurements":[{"id":"photo","value":2.685,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard 588ce841463f (Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630)","scaleRef":"its top rail's 37 teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 23.548 px a tooth, 59.77 px/in","method":"a round hole about 22 px across at px 800 (mirrored); only 0.18 x 0.32 shows through","via":"harvest"}}],"note":"Aero: \"Quick disconnect sling socket at the 3, 6 and 9 o'clock positions\". The one underneath isn't seen from the side."},"qd_socket_d":{"label":"The QD sling socket's diameter, as it shows","kind":"length","measurements":[{"id":"photo","value":0.37,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-15-handguard 588ce841463f (Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630)","scaleRef":"its top rail's 37 teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 23.548 px a tooth, 59.77 px/in","method":"the round hole's outline, about 22 px","via":"harvest"}}]}}},{"subject":"aero-r-one-16-6-handguard","title":"Aero Precision AR15 16.6 in R-ONE M-LOK handguard (APRA500706A)","dimensions":{"weight":{"label":"Weight (the handguard)","kind":"mass","measurements":[{"id":"primary-arms","value":10.1,"unit":"oz","pm":0.1,"stated":"At the top of the R-ONE length lineup and weighing roughly 10.1 oz.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Aero Precision ATLAS R-ONE M-LOK AR-15 Handguard - 16.6\" (APRA500706A), description","url":"https://www.primaryarms.com/aero-precision-atlas-r-one-m-lok-ar-15-handguard-16-6in","retrieved":"2026-11-03","via":"harvest"}},{"id":"primary-arms-table","value":9.07,"unit":"oz","pm":0.005,"stated":"Weight 9.07 Oz","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Aero Precision ATLAS R-ONE M-LOK AR-15 Handguard - 16.6\" (APRA500706A), Specifications","url":"https://www.primaryarms.com/aero-precision-atlas-r-one-m-lok-ar-15-handguard-16-6in","retrieved":"2026-11-03","via":"harvest"}}],"adopt":{"from":"primary-arms","reason":"The description's figure: the table's is the 15 in's to the hundredth, and the longer handguard's metal (its model as aluminium, 10.0 oz) agrees with 10.1."},"note":"Aero's own page for this length alone isn't found; Primary Arms' page gives two figures. Its specifications table's 9.07 oz is to the hundredth Aero's figure for the 15 in (aero-r-one-15-handguard.weight), and a handguard 1.6 in longer of the same section weighs more: the model of this one, as aluminium, comes to 10.0 oz, and of the 15 in to 9.2."},"length":{"label":"Length (the receiver's face to the end of the last rail slot)","kind":"length","measurements":[{"id":"primary-arms","value":16.6,"unit":"in","pm":0.05,"stated":"Length: 16.6\"","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Aero Precision ATLAS R-ONE M-LOK AR-15 Handguard - 16.6\"","url":"https://www.primaryarms.com/aero-precision-atlas-r-one-m-lok-ar-15-handguard-16-6in","retrieved":"2026-11-03","via":"harvest"}}],"note":"Aero's own list of the R-ONE's lengths (\"Actual Handguard Lengths 4.8\\\", 7.3\\\", 9.3\\\", 10.3\\\", 12.7\\\", 15\\\"\") hasn't this one, and Aero's page for it alone isn't found: its length is the seller's and the configurable page's (\"16.6\\\"\"); its weight isn't on file."},"overall_length":{"label":"Overall length, end to end","kind":"length","measurements":[{"id":"photo","value":16.906,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-16-6-handguard 9218ad7902eb (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 631)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 21.255 px a tooth, 53.95 px/in","method":"the silhouette end to end, 912 px","via":"harvest"}},{"id":"photo-right","value":16.908,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-16-6-handguard 8c7793ba4455 (Aero's gallery: the R-ONE's right side, the check, 1000 x 631)","scaleRef":"its own rail teeth fitted to the same pitch","method":"the silhouette end to end","via":"harvest"}}],"adopt":{"from":"photo","reason":"The left view, the one traced (the 15 in's was traced from the same view); the right view's reading is within its ±."}},"rail_slots":{"label":"Slots in its top rail","kind":"count","measurements":[{"id":"photo","value":41,"unit":"count","source":{"type":"photo","photo":"references/aero-r-one-16-6-handguard 9218ad7902eb (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 631)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 21.255 px a tooth, 53.95 px/in","method":"the gaps between the teeth along the whole rail, counted; they lie on the Picatinny pitch end to end within 0.02 in","via":"harvest"}},{"id":"photo-right","value":41,"unit":"count","source":{"type":"photo","photo":"references/aero-r-one-16-6-handguard 8c7793ba4455 (Aero's gallery: the R-ONE's right side, the check, 1000 x 631)","scaleRef":"its own rail teeth fitted to the same pitch","method":"counted","via":"harvest"}}],"adopt":{"from":"photo","reason":"Both views read the same; the left view's is the one traced (the 15 in's was traced from the same view)."}},"rail_slot0_from_rear":{"label":"Its rail's rearmost slot (its centre) ahead of the outline's rear end","kind":"length","measurements":[{"id":"photo","value":0.751,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-16-6-handguard 9218ad7902eb (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 631)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 21.255 px a tooth, 53.95 px/in","method":"the first gap between the teeth, its own centre (on the 15 in's view this reads 0.842 for that ledger's 0.855)","via":"harvest"}},{"id":"photo-right","value":0.797,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-16-6-handguard 8c7793ba4455 (Aero's gallery: the R-ONE's right side, the check, 1000 x 631)","scaleRef":"its own rail teeth fitted to the same pitch","method":"the same","via":"harvest"}}],"adopt":{"from":"photo-right","reason":"The right view: the left view, the coarsest of the family (54 px to the inch), reads its first gap 0.046 further back, where its own outline's first tooth stands 0.03 behind where that reading would put it; the right view's agrees with that tooth (0.015, as the 15 in's does by 0.04) and with every other length's (0.80 to 0.84)."}},"rail_front_from_rear":{"label":"Its rail's front end (the end of the last slot) ahead of the outline's rear end","kind":"length","measurements":[{"id":"photo","value":16.868,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-r-one-16-6-handguard 9218ad7902eb (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 631)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 21.255 px a tooth, 53.95 px/in","method":"the rail's top's last solid column ahead of its last slot","via":"harvest"}}]},"qd_socket_from_rear":{"label":"The QD sling socket on each side (3 and 9 o'clock), its centre ahead of the outline's rear end","kind":"length","measurements":[{"id":"photo","value":2.613,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/aero-r-one-16-6-handguard 9218ad7902eb (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 631)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 21.255 px a tooth, 53.95 px/in","method":"the round hole behind the M-LOK row, what shows through both walls","via":"harvest"}},{"id":"photo-right","value":2.654,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/aero-r-one-16-6-handguard 8c7793ba4455 (Aero's gallery: the R-ONE's right side, the check, 1000 x 631)","scaleRef":"its own rail teeth fitted to the same pitch","method":"the same","via":"harvest"}}],"adopt":{"from":"photo","reason":"The left view, the one traced; the two views differ by their yaw."}},"short_slot_length":{"label":"The short slot's length (at least: what shows through both walls)","kind":"length","measurements":[{"id":"photo","value":0.593,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-16-6-handguard 9218ad7902eb (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 631)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 21.255 px a tooth, 53.95 px/in","method":"the shorter slot between the QD socket and the M-LOK row: what shows through both walls","via":"harvest"}},{"id":"photo-right","value":0.463,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-16-6-handguard 8c7793ba4455 (Aero's gallery: the R-ONE's right side, the check, 1000 x 631)","scaleRef":"its own rail teeth fitted to the same pitch","method":"the same","via":"harvest"}}],"adopt":{"from":"photo","reason":"The longer reading: a slot seen through both walls at a slant shows less than it is, never more."}},"short_slot_rear_from_rear":{"label":"The short slot's rear end ahead of the outline's rear end","kind":"length","measurements":[{"id":"derived","value":3.345,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"3.641in - {.short_slot_length} / 2","via":"harvest"},"note":"Its centre on the left view, 3.641 in (the right view: 3.672)."}]},"mlok_slots":{"label":"How many M-LOK slots on each side","kind":"count","measurements":[{"id":"photo","value":8,"unit":"count","source":{"type":"photo","photo":"references/aero-r-one-16-6-handguard 9218ad7902eb (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 631)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 21.255 px a tooth, 53.95 px/in","method":"counted: the full-length slots in the row at the bore's level","via":"harvest"}},{"id":"photo-right","value":8,"unit":"count","source":{"type":"photo","photo":"references/aero-r-one-16-6-handguard 8c7793ba4455 (Aero's gallery: the R-ONE's right side, the check, 1000 x 631)","scaleRef":"its own rail teeth fitted to the same pitch","method":"counted","via":"harvest"}}],"adopt":{"from":"photo","reason":"Both views read the same; the left view's is the one traced (the 15 in's was traced from the same view)."}},"mlok_slot0_from_rear":{"label":"The rearmost M-LOK slot's centre on its sides, ahead of the handguard's rear end (its outline's x = 0)","kind":"length","measurements":[{"id":"photo","value":4.869,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-16-6-handguard 9218ad7902eb (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 631)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 21.255 px a tooth, 53.95 px/in","method":"the full-length slots' centres along their row, on the M-LOK pitch (std.mlok.slot_pitch) within 0.3%","via":"harvest"}},{"id":"photo-right","value":4.911,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-16-6-handguard 8c7793ba4455 (Aero's gallery: the R-ONE's right side, the check, 1000 x 631)","scaleRef":"its own rail teeth fitted to the same pitch","method":"the same","via":"harvest"}}],"adopt":{"from":"photo","reason":"The left view, the one traced; the two views differ by their yaw."}},"mlok_slot0_x":{"label":"The rearmost M-LOK slot's centre ahead of the receiver's face","kind":"length","measurements":[{"id":"derived","value":4.106,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.rear_x} + {.mlok_slot0_from_rear}","via":"harvest"}}]},"thin_slot_count":{"label":"Thin slots in each row","kind":"count","measurements":[{"id":"photo","value":13,"unit":"count","source":{"type":"photo","photo":"references/aero-r-one-16-6-handguard 9218ad7902eb (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 631)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 21.255 px a tooth, 53.95 px/in","method":"counted in each of the four rows","via":"harvest"}},{"id":"photo-right","value":13,"unit":"count","source":{"type":"photo","photo":"references/aero-r-one-16-6-handguard 8c7793ba4455 (Aero's gallery: the R-ONE's right side, the check, 1000 x 631)","scaleRef":"its own rail teeth fitted to the same pitch","method":"counted","via":"harvest"}}],"adopt":{"from":"photo","reason":"Both views read the same; the left view's is the one traced (the 15 in's was traced from the same view)."}},"thin_slot_first_from_rear":{"label":"The thin slots' first centre ahead of the outline's rear end (all four rows)","kind":"length","measurements":[{"id":"photo","value":3.043,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-16-6-handguard 9218ad7902eb (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 631)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 21.255 px a tooth, 53.95 px/in","method":"the see-through slots' centres in the four rows fitted to one pitch","via":"harvest"}},{"id":"photo-right","value":3.08,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-16-6-handguard 8c7793ba4455 (Aero's gallery: the R-ONE's right side, the check, 1000 x 631)","scaleRef":"its own rail teeth fitted to the same pitch","method":"the same","via":"harvest"}}],"adopt":{"from":"photo","reason":"The left view, the one traced; the two views differ by their yaw."}},"thin_slot_pitch":{"label":"The thin slots' pitch","kind":"length","measurements":[{"id":"photo","value":1.099,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/aero-r-one-16-6-handguard 9218ad7902eb (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 631)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 21.255 px a tooth, 53.95 px/in","method":"their centres' spacing in the four rows","via":"harvest"}}],"note":"Each length's own: the slots are spread over its length (the 15 in's 1.0685, this one's the one read here)."},"thin_slot_length":{"label":"A thin slot's length (at least: what shows through both walls)","kind":"length","measurements":[{"id":"photo","value":1.001,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-r-one-16-6-handguard 9218ad7902eb (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 631)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 21.255 px a tooth, 53.95 px/in","method":"the longest see-through slot in the four rows","via":"harvest"}}]},"rear_x":{"label":"The handguard's rear end (its two side tabs' ends) against the receiver's front face (negative: behind it)","kind":"length","measurements":[{"id":"family","value":-0.763,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rear_x}","via":"harvest"}}],"note":"The clamp is the family's: the 15 in's place by reference. On this length's view the first tooth's rear face is 0.463 in ahead of the tabs' ends (the 15 in's, read the same way, 0.517); and Aero's length, back from the rail's end, puts the receiver's face 0.268 in ahead of them where the 15 in's puts it 0.318: within what a length stated to a tenth (0.05) and the two readings (0.02 each) carry."},"rail_top_above_bore":{"label":"Its rail's top above the bore (level with the receiver's)","kind":"length","measurements":[{"id":"family","value":1.2125,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rail_top_above_bore}","via":"harvest"}}]},"width":{"label":"The R-ONE family: the 15 in's width","kind":"length","measurements":[{"id":"family","value":1.5,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.width}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"height":{"label":"The R-ONE family: the 15 in's height","kind":"length","measurements":[{"id":"family","value":1.95,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.height}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"inside_diameter":{"label":"The R-ONE family: the 15 in's inside diameter","kind":"length","measurements":[{"id":"family","value":1.3,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.inside_diameter}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"inside_height":{"label":"The R-ONE family: the 15 in's inside height","kind":"length","measurements":[{"id":"family","value":1.65,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.inside_height}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"bottom_flat_width":{"label":"The R-ONE family: the 15 in's bottom flat width","kind":"length","measurements":[{"id":"family","value":0.609,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.bottom_flat_width}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"side_top_width":{"label":"The R-ONE family: the 15 in's side top width","kind":"length","measurements":[{"id":"family","value":1.455,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.side_top_width}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"lower_edge_width":{"label":"The R-ONE family: the 15 in's lower edge width","kind":"length","measurements":[{"id":"family","value":1.133,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.lower_edge_width}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"lower_edge_below_rail_top":{"label":"The R-ONE family: the 15 in's lower edge below rail top","kind":"length","measurements":[{"id":"family","value":1.759,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.lower_edge_below_rail_top}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"rail_neck_width":{"label":"The R-ONE family: the 15 in's rail neck width","kind":"length","measurements":[{"id":"family","value":0.62,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rail_neck_width}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"rail_neck_foot_below_rail_top":{"label":"The R-ONE family: the 15 in's rail neck foot below rail top","kind":"length","measurements":[{"id":"family","value":0.377,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rail_neck_foot_below_rail_top}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"rail_centre_gap":{"label":"The R-ONE family: the 15 in's rail centre gap","kind":"length","measurements":[{"id":"family","value":0.365,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rail_centre_gap}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"rail_window_length":{"label":"The R-ONE family: the 15 in's rail window length","kind":"length","measurements":[{"id":"family","value":0.54,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rail_window_length}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"rail_bridge_recess":{"label":"The R-ONE family: the 15 in's rail bridge recess","kind":"length","measurements":[{"id":"family","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rail_bridge_recess}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"side_flat_top_below_rail_top":{"label":"The R-ONE family: the 15 in's side flat top below rail top","kind":"length","measurements":[{"id":"family","value":0.88,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.side_flat_top_below_rail_top}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"side_flat_bottom_below_rail_top":{"label":"The R-ONE family: the 15 in's side flat bottom below rail top","kind":"length","measurements":[{"id":"family","value":1.502,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.side_flat_bottom_below_rail_top}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"thin_slot_width":{"label":"The R-ONE family: the 15 in's thin slot width","kind":"length","measurements":[{"id":"family","value":0.22,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.thin_slot_width}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"thin_slot_row_a_y":{"label":"The R-ONE family: the 15 in's thin slot row a y","kind":"length","measurements":[{"id":"family","value":0.71,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.thin_slot_row_a_y}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"thin_slot_row_b_y":{"label":"The R-ONE family: the 15 in's thin slot row b y","kind":"length","measurements":[{"id":"family","value":0.46,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.thin_slot_row_b_y}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"thin_slot_row_d_y":{"label":"The R-ONE family: the 15 in's thin slot row d y","kind":"length","measurements":[{"id":"family","value":-0.41,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.thin_slot_row_d_y}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"thin_slot_row_e_y":{"label":"The R-ONE family: the 15 in's thin slot row e y","kind":"length","measurements":[{"id":"family","value":-0.635,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.thin_slot_row_e_y}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"qd_socket_d":{"label":"The R-ONE family: the 15 in's qd socket d","kind":"length","measurements":[{"id":"family","value":0.37,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.qd_socket_d}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"reach_inside":{"label":"The room inside its side faces before the barrel, at the M-LOK slots (what an accessory's nuts may take)","kind":"length","measurements":[],"note":"Not read: as on the 15 in, it depends on the barrel under it."}}},{"subject":"aero-r-one-7-3-handguard","title":"Aero Precision AR15 7.3 in R-ONE M-LOK handguard (APRA500701A)","dimensions":{"weight":{"label":"Weight (the handguard; its mounting hardware is listed apart)","kind":"mass","measurements":[{"id":"aero","value":5.22,"unit":"oz","pm":0.01,"stated":"Weight(s) 5.22 oz","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, AR15 7.3\" R-ONE M-LOK Handguard, Specifications","url":"https://www.aeroprecisionusa.com/ar15-7-atlas-r-one-m-lok-handguard-anodized-black","retrieved":"2026-11-03","via":"harvest"}}]},"length":{"label":"Length (the receiver's face to the end of the last rail slot)","kind":"length","measurements":[{"id":"aero","value":7.3,"unit":"in","pm":0.05,"stated":"Handguard Length 7.3\"","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, AR15 7.3\" R-ONE M-LOK Handguard, Specifications","url":"https://www.aeroprecisionusa.com/ar15-7-atlas-r-one-m-lok-handguard-anodized-black","retrieved":"2026-11-03","via":"harvest"}}],"note":"Aero: \"Aero Precision rail lengths measure from end to end. This is the point of contact at the receiver to the end of the last picatinny slot at the muzzle.\""},"overall_length":{"label":"Overall length, end to end","kind":"length","measurements":[{"id":"photo","value":7.586,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-7-3-handguard af919473e69d (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 630)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 47.626 px a tooth, 120.88 px/in","method":"the silhouette end to end, 917 px","via":"harvest"}},{"id":"photo-right","value":7.594,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-7-3-handguard c32b82fd6101 (Aero's gallery: the R-ONE's right side, the check, 1000 x 630)","scaleRef":"its own rail teeth fitted to the same pitch","method":"the silhouette end to end","via":"harvest"}}],"adopt":{"from":"photo","reason":"The left view, the one traced (the 15 in's was traced from the same view); the right view's reading is within its ±."}},"rail_slots":{"label":"Slots in its top rail","kind":"count","measurements":[{"id":"photo","value":17,"unit":"count","source":{"type":"photo","photo":"references/aero-r-one-7-3-handguard af919473e69d (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 630)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 47.626 px a tooth, 120.88 px/in","method":"the gaps between the teeth along the whole rail, counted; they lie on the Picatinny pitch end to end within 0.02 in","via":"harvest"}},{"id":"photo-right","value":17,"unit":"count","source":{"type":"photo","photo":"references/aero-r-one-7-3-handguard c32b82fd6101 (Aero's gallery: the R-ONE's right side, the check, 1000 x 630)","scaleRef":"its own rail teeth fitted to the same pitch","method":"counted","via":"harvest"}}],"adopt":{"from":"photo","reason":"Both views read the same; the left view's is the one traced (the 15 in's was traced from the same view)."}},"rail_slot0_from_rear":{"label":"Its rail's rearmost slot (its centre) ahead of the outline's rear end","kind":"length","measurements":[{"id":"photo","value":0.798,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-7-3-handguard af919473e69d (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 630)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 47.626 px a tooth, 120.88 px/in","method":"the first gap between the teeth, its own centre (on the 15 in's view this reads 0.842 for that ledger's 0.855)","via":"harvest"}},{"id":"photo-right","value":0.799,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-7-3-handguard c32b82fd6101 (Aero's gallery: the R-ONE's right side, the check, 1000 x 630)","scaleRef":"its own rail teeth fitted to the same pitch","method":"the same","via":"harvest"}}],"adopt":{"from":"photo","reason":"The left view, the one traced (the 15 in's was traced from the same view); the right view's reading is within its ±."}},"rail_front_from_rear":{"label":"Its rail's front end (the end of the last slot) ahead of the outline's rear end","kind":"length","measurements":[{"id":"photo","value":7.561,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-r-one-7-3-handguard af919473e69d (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 630)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 47.626 px a tooth, 120.88 px/in","method":"the rail's top's last solid column ahead of its last slot","via":"harvest"}}]},"qd_socket_from_rear":{"label":"The QD sling socket on each side (3 and 9 o'clock), its centre ahead of the outline's rear end","kind":"length","measurements":[{"id":"photo","value":2.818,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/aero-r-one-7-3-handguard af919473e69d (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 630)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 47.626 px a tooth, 120.88 px/in","method":"the round hole behind the M-LOK row, what shows through both walls","via":"harvest"}},{"id":"photo-right","value":2.819,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/aero-r-one-7-3-handguard c32b82fd6101 (Aero's gallery: the R-ONE's right side, the check, 1000 x 630)","scaleRef":"its own rail teeth fitted to the same pitch","method":"the same","via":"harvest"}}],"adopt":{"from":"photo","reason":"The left view, the one traced (the 15 in's was traced from the same view); the right view's reading is within its ±."}},"short_slot_length":{"label":"The short slot's length (at least: what shows through both walls)","kind":"length","measurements":[{"id":"photo","value":0.48,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-7-3-handguard af919473e69d (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 630)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 47.626 px a tooth, 120.88 px/in","method":"the shorter slot between the QD socket and the M-LOK row: what shows through both walls","via":"harvest"}},{"id":"photo-right","value":0.489,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-7-3-handguard c32b82fd6101 (Aero's gallery: the R-ONE's right side, the check, 1000 x 630)","scaleRef":"its own rail teeth fitted to the same pitch","method":"the same","via":"harvest"}}],"adopt":{"from":"photo","reason":"The left view, the one traced (the 15 in's was traced from the same view); the right view's reading is within its ±."}},"short_slot_rear_from_rear":{"label":"The short slot's rear end ahead of the outline's rear end","kind":"length","measurements":[{"id":"derived","value":3.607,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"3.851in - {.short_slot_length} / 2","via":"harvest"},"note":"Its centre on the left view, 3.851 in (the right view: 3.85)."}]},"mlok_slots":{"label":"How many M-LOK slots on each side","kind":"count","measurements":[{"id":"photo","value":2,"unit":"count","source":{"type":"photo","photo":"references/aero-r-one-7-3-handguard af919473e69d (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 630)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 47.626 px a tooth, 120.88 px/in","method":"counted: the full-length slots in the row at the bore's level","via":"harvest"}},{"id":"photo-right","value":2,"unit":"count","source":{"type":"photo","photo":"references/aero-r-one-7-3-handguard c32b82fd6101 (Aero's gallery: the R-ONE's right side, the check, 1000 x 630)","scaleRef":"its own rail teeth fitted to the same pitch","method":"counted","via":"harvest"}}],"adopt":{"from":"photo","reason":"Both views read the same; the left view's is the one traced (the 15 in's was traced from the same view)."}},"mlok_slot0_from_rear":{"label":"The rearmost M-LOK slot's centre on its sides, ahead of the handguard's rear end (its outline's x = 0)","kind":"length","measurements":[{"id":"photo","value":5.029,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-7-3-handguard af919473e69d (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 630)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 47.626 px a tooth, 120.88 px/in","method":"the full-length slots' centres along their row, on the M-LOK pitch (std.mlok.slot_pitch) within 0.3%","via":"harvest"}},{"id":"photo-right","value":5.027,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-7-3-handguard c32b82fd6101 (Aero's gallery: the R-ONE's right side, the check, 1000 x 630)","scaleRef":"its own rail teeth fitted to the same pitch","method":"the same","via":"harvest"}}],"adopt":{"from":"photo","reason":"The left view, the one traced (the 15 in's was traced from the same view); the right view's reading is within its ±."}},"mlok_slot0_x":{"label":"The rearmost M-LOK slot's centre ahead of the receiver's face","kind":"length","measurements":[{"id":"derived","value":4.266,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.rear_x} + {.mlok_slot0_from_rear}","via":"harvest"}}]},"thin_slot_count":{"label":"Thin slots in each row","kind":"count","measurements":[{"id":"photo","value":5,"unit":"count","source":{"type":"photo","photo":"references/aero-r-one-7-3-handguard af919473e69d (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 630)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 47.626 px a tooth, 120.88 px/in","method":"counted in each of the four rows","via":"harvest"}},{"id":"photo-right","value":5,"unit":"count","source":{"type":"photo","photo":"references/aero-r-one-7-3-handguard c32b82fd6101 (Aero's gallery: the R-ONE's right side, the check, 1000 x 630)","scaleRef":"its own rail teeth fitted to the same pitch","method":"counted","via":"harvest"}}],"adopt":{"from":"photo","reason":"Both views read the same; the left view's is the one traced (the 15 in's was traced from the same view)."}},"thin_slot_first_from_rear":{"label":"The thin slots' first centre ahead of the outline's rear end (all four rows)","kind":"length","measurements":[{"id":"photo","value":3.105,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-7-3-handguard af919473e69d (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 630)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 47.626 px a tooth, 120.88 px/in","method":"the see-through slots' centres in the four rows fitted to one pitch","via":"harvest"}},{"id":"photo-right","value":3.106,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-7-3-handguard c32b82fd6101 (Aero's gallery: the R-ONE's right side, the check, 1000 x 630)","scaleRef":"its own rail teeth fitted to the same pitch","method":"the same","via":"harvest"}}],"adopt":{"from":"photo","reason":"The left view, the one traced (the 15 in's was traced from the same view); the right view's reading is within its ±."}},"thin_slot_pitch":{"label":"The thin slots' pitch","kind":"length","measurements":[{"id":"photo","value":0.977,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/aero-r-one-7-3-handguard af919473e69d (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 630)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 47.626 px a tooth, 120.88 px/in","method":"their centres' spacing in the four rows","via":"harvest"}}],"note":"Each length's own: the slots are spread over its length (the 15 in's 1.0685, this one's the one read here)."},"thin_slot_length":{"label":"A thin slot's length (at least: what shows through both walls)","kind":"length","measurements":[{"id":"photo","value":0.845,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-r-one-7-3-handguard af919473e69d (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 630)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 47.626 px a tooth, 120.88 px/in","method":"the longest see-through slot in the four rows","via":"harvest"}}]},"rear_x":{"label":"The handguard's rear end (its two side tabs' ends) against the receiver's front face (negative: behind it)","kind":"length","measurements":[{"id":"family","value":-0.763,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rear_x}","via":"harvest"}}],"note":"The clamp is the family's: the 15 in's place by reference. On this length's view the first tooth's rear face is 0.488 in ahead of the tabs' ends (the 15 in's, read the same way, 0.517); and Aero's length, back from the rail's end, puts the receiver's face 0.261 in ahead of them where the 15 in's puts it 0.318: within what a length stated to a tenth (0.05) and the two readings (0.02 each) carry."},"rail_top_above_bore":{"label":"Its rail's top above the bore (level with the receiver's)","kind":"length","measurements":[{"id":"family","value":1.2125,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rail_top_above_bore}","via":"harvest"}}]},"width":{"label":"The R-ONE family: the 15 in's width","kind":"length","measurements":[{"id":"family","value":1.5,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.width}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"height":{"label":"The R-ONE family: the 15 in's height","kind":"length","measurements":[{"id":"family","value":1.95,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.height}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"inside_diameter":{"label":"The R-ONE family: the 15 in's inside diameter","kind":"length","measurements":[{"id":"family","value":1.3,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.inside_diameter}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"inside_height":{"label":"The R-ONE family: the 15 in's inside height","kind":"length","measurements":[{"id":"family","value":1.65,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.inside_height}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"bottom_flat_width":{"label":"The R-ONE family: the 15 in's bottom flat width","kind":"length","measurements":[{"id":"family","value":0.609,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.bottom_flat_width}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"side_top_width":{"label":"The R-ONE family: the 15 in's side top width","kind":"length","measurements":[{"id":"family","value":1.455,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.side_top_width}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"lower_edge_width":{"label":"The R-ONE family: the 15 in's lower edge width","kind":"length","measurements":[{"id":"family","value":1.133,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.lower_edge_width}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"lower_edge_below_rail_top":{"label":"The R-ONE family: the 15 in's lower edge below rail top","kind":"length","measurements":[{"id":"family","value":1.759,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.lower_edge_below_rail_top}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"rail_neck_width":{"label":"The R-ONE family: the 15 in's rail neck width","kind":"length","measurements":[{"id":"family","value":0.62,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rail_neck_width}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"rail_neck_foot_below_rail_top":{"label":"The R-ONE family: the 15 in's rail neck foot below rail top","kind":"length","measurements":[{"id":"family","value":0.377,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rail_neck_foot_below_rail_top}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"rail_centre_gap":{"label":"The R-ONE family: the 15 in's rail centre gap","kind":"length","measurements":[{"id":"family","value":0.365,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rail_centre_gap}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"rail_window_length":{"label":"The R-ONE family: the 15 in's rail window length","kind":"length","measurements":[{"id":"family","value":0.54,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rail_window_length}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"rail_bridge_recess":{"label":"The R-ONE family: the 15 in's rail bridge recess","kind":"length","measurements":[{"id":"family","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rail_bridge_recess}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"side_flat_top_below_rail_top":{"label":"The R-ONE family: the 15 in's side flat top below rail top","kind":"length","measurements":[{"id":"family","value":0.88,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.side_flat_top_below_rail_top}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"side_flat_bottom_below_rail_top":{"label":"The R-ONE family: the 15 in's side flat bottom below rail top","kind":"length","measurements":[{"id":"family","value":1.502,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.side_flat_bottom_below_rail_top}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"thin_slot_width":{"label":"The R-ONE family: the 15 in's thin slot width","kind":"length","measurements":[{"id":"family","value":0.22,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.thin_slot_width}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"thin_slot_row_a_y":{"label":"The R-ONE family: the 15 in's thin slot row a y","kind":"length","measurements":[{"id":"family","value":0.71,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.thin_slot_row_a_y}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"thin_slot_row_b_y":{"label":"The R-ONE family: the 15 in's thin slot row b y","kind":"length","measurements":[{"id":"family","value":0.46,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.thin_slot_row_b_y}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"thin_slot_row_d_y":{"label":"The R-ONE family: the 15 in's thin slot row d y","kind":"length","measurements":[{"id":"family","value":-0.41,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.thin_slot_row_d_y}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"thin_slot_row_e_y":{"label":"The R-ONE family: the 15 in's thin slot row e y","kind":"length","measurements":[{"id":"family","value":-0.635,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.thin_slot_row_e_y}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"qd_socket_d":{"label":"The R-ONE family: the 15 in's qd socket d","kind":"length","measurements":[{"id":"family","value":0.37,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.qd_socket_d}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"reach_inside":{"label":"The room inside its side faces before the barrel, at the M-LOK slots (what an accessory's nuts may take)","kind":"length","measurements":[],"note":"Not read: as on the 15 in, it depends on the barrel under it."}}},{"subject":"aero-r-one-9-3-handguard","title":"Aero Precision AR15 9.3 in R-ONE M-LOK handguard (APRA500702A)","dimensions":{"weight":{"label":"Weight (the handguard; its mounting hardware is listed apart)","kind":"mass","measurements":[{"id":"aero","value":6.03,"unit":"oz","pm":0.01,"stated":"Weight(s) 6.03 oz","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, AR15 9.3\" R-ONE M-LOK Handguard, Specifications","url":"https://www.aeroprecisionusa.com/ar15-9-atlas-r-one-m-lok-handguard-anodized-black","retrieved":"2026-11-03","via":"harvest"}}]},"length":{"label":"Length (the receiver's face to the end of the last rail slot)","kind":"length","measurements":[{"id":"aero","value":9.3,"unit":"in","pm":0.05,"stated":"Handguard Length 9.3\"","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, AR15 9.3\" R-ONE M-LOK Handguard, Specifications","url":"https://www.aeroprecisionusa.com/ar15-9-atlas-r-one-m-lok-handguard-anodized-black","retrieved":"2026-11-03","via":"harvest"}}],"note":"Aero: \"Aero Precision rail lengths measure from end to end. This is the point of contact at the receiver to the end of the last picatinny slot at the muzzle.\""},"overall_length":{"label":"Overall length, end to end","kind":"length","measurements":[{"id":"photo","value":9.594,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-9-3-handguard f4a8b5638442 (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 630)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 37.576 px a tooth, 95.37 px/in","method":"the silhouette end to end, 915 px","via":"harvest"}},{"id":"photo-right","value":9.601,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-9-3-handguard 4b4e44b7af8b (Aero's gallery: the R-ONE's right side, the check, 1000 x 630)","scaleRef":"its own rail teeth fitted to the same pitch","method":"the silhouette end to end","via":"harvest"}}],"adopt":{"from":"photo","reason":"The left view, the one traced (the 15 in's was traced from the same view); the right view's reading is within its ±."}},"rail_slots":{"label":"Slots in its top rail","kind":"count","measurements":[{"id":"photo","value":22,"unit":"count","source":{"type":"photo","photo":"references/aero-r-one-9-3-handguard f4a8b5638442 (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 630)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 37.576 px a tooth, 95.37 px/in","method":"the gaps between the teeth along the whole rail, counted; they lie on the Picatinny pitch end to end within 0.02 in","via":"harvest"}},{"id":"photo-right","value":22,"unit":"count","source":{"type":"photo","photo":"references/aero-r-one-9-3-handguard 4b4e44b7af8b (Aero's gallery: the R-ONE's right side, the check, 1000 x 630)","scaleRef":"its own rail teeth fitted to the same pitch","method":"counted","via":"harvest"}}],"adopt":{"from":"photo","reason":"Both views read the same; the left view's is the one traced (the 15 in's was traced from the same view)."}},"rail_slot0_from_rear":{"label":"Its rail's rearmost slot (its centre) ahead of the outline's rear end","kind":"length","measurements":[{"id":"photo","value":0.828,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-9-3-handguard f4a8b5638442 (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 630)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 37.576 px a tooth, 95.37 px/in","method":"the first gap between the teeth, its own centre (on the 15 in's view this reads 0.842 for that ledger's 0.855)","via":"harvest"}},{"id":"photo-right","value":0.803,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-9-3-handguard 4b4e44b7af8b (Aero's gallery: the R-ONE's right side, the check, 1000 x 630)","scaleRef":"its own rail teeth fitted to the same pitch","method":"the same","via":"harvest"}}],"adopt":{"from":"photo","reason":"The left view, the one traced (the 15 in's was traced from the same view); the right view's reading is within its ±."}},"rail_front_from_rear":{"label":"Its rail's front end (the end of the last slot) ahead of the outline's rear end","kind":"length","measurements":[{"id":"photo","value":9.573,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-r-one-9-3-handguard f4a8b5638442 (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 630)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 37.576 px a tooth, 95.37 px/in","method":"the rail's top's last solid column ahead of its last slot","via":"harvest"}}]},"qd_socket_from_rear":{"label":"The QD sling socket on each side (3 and 9 o'clock), its centre ahead of the outline's rear end","kind":"length","measurements":[{"id":"photo","value":2.568,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/aero-r-one-9-3-handguard f4a8b5638442 (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 630)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 37.576 px a tooth, 95.37 px/in","method":"the round hole behind the M-LOK row, what shows through both walls","via":"harvest"}},{"id":"photo-right","value":2.554,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/aero-r-one-9-3-handguard 4b4e44b7af8b (Aero's gallery: the R-ONE's right side, the check, 1000 x 630)","scaleRef":"its own rail teeth fitted to the same pitch","method":"the same","via":"harvest"}}],"adopt":{"from":"photo","reason":"The left view, the one traced (the 15 in's was traced from the same view); the right view's reading is within its ±."}},"mlok_slots":{"label":"How many M-LOK slots on each side","kind":"count","measurements":[{"id":"photo","value":4,"unit":"count","source":{"type":"photo","photo":"references/aero-r-one-9-3-handguard f4a8b5638442 (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 630)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 37.576 px a tooth, 95.37 px/in","method":"counted: the full-length slots in the row at the bore's level","via":"harvest"}},{"id":"photo-right","value":4,"unit":"count","source":{"type":"photo","photo":"references/aero-r-one-9-3-handguard 4b4e44b7af8b (Aero's gallery: the R-ONE's right side, the check, 1000 x 630)","scaleRef":"its own rail teeth fitted to the same pitch","method":"counted","via":"harvest"}}],"adopt":{"from":"photo","reason":"Both views read the same; the left view's is the one traced (the 15 in's was traced from the same view)."}},"mlok_slot0_from_rear":{"label":"The rearmost M-LOK slot's centre on its sides, ahead of the handguard's rear end (its outline's x = 0)","kind":"length","measurements":[{"id":"photo","value":3.891,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-9-3-handguard f4a8b5638442 (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 630)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 37.576 px a tooth, 95.37 px/in","method":"the full-length slots' centres along their row, on the M-LOK pitch (std.mlok.slot_pitch) within 0.3%","via":"harvest"}},{"id":"photo-right","value":3.876,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-9-3-handguard 4b4e44b7af8b (Aero's gallery: the R-ONE's right side, the check, 1000 x 630)","scaleRef":"its own rail teeth fitted to the same pitch","method":"the same","via":"harvest"}}],"adopt":{"from":"photo","reason":"The left view, the one traced (the 15 in's was traced from the same view); the right view's reading is within its ±."}},"mlok_slot0_x":{"label":"The rearmost M-LOK slot's centre ahead of the receiver's face","kind":"length","measurements":[{"id":"derived","value":3.128,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.rear_x} + {.mlok_slot0_from_rear}","via":"harvest"}}]},"thin_slot_count":{"label":"Thin slots in each row","kind":"count","measurements":[{"id":"photo","value":7,"unit":"count","source":{"type":"photo","photo":"references/aero-r-one-9-3-handguard f4a8b5638442 (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 630)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 37.576 px a tooth, 95.37 px/in","method":"counted in each of the four rows","via":"harvest"}},{"id":"photo-right","value":7,"unit":"count","source":{"type":"photo","photo":"references/aero-r-one-9-3-handguard 4b4e44b7af8b (Aero's gallery: the R-ONE's right side, the check, 1000 x 630)","scaleRef":"its own rail teeth fitted to the same pitch","method":"counted","via":"harvest"}}],"adopt":{"from":"photo","reason":"Both views read the same; the left view's is the one traced (the 15 in's was traced from the same view)."}},"thin_slot_first_from_rear":{"label":"The thin slots' first centre ahead of the outline's rear end (all four rows)","kind":"length","measurements":[{"id":"photo","value":2.871,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-9-3-handguard f4a8b5638442 (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 630)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 37.576 px a tooth, 95.37 px/in","method":"the see-through slots' centres in the four rows fitted to one pitch","via":"harvest"}},{"id":"photo-right","value":2.865,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-r-one-9-3-handguard 4b4e44b7af8b (Aero's gallery: the R-ONE's right side, the check, 1000 x 630)","scaleRef":"its own rail teeth fitted to the same pitch","method":"the same","via":"harvest"}}],"adopt":{"from":"photo","reason":"The left view, the one traced (the 15 in's was traced from the same view); the right view's reading is within its ±."}},"thin_slot_pitch":{"label":"The thin slots' pitch","kind":"length","measurements":[{"id":"photo","value":1.018,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/aero-r-one-9-3-handguard f4a8b5638442 (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 630)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 37.576 px a tooth, 95.37 px/in","method":"their centres' spacing in the four rows","via":"harvest"}}],"note":"Each length's own: the slots are spread over its length (the 15 in's 1.0685, this one's the one read here)."},"thin_slot_length":{"label":"A thin slot's length (at least: what shows through both walls)","kind":"length","measurements":[{"id":"photo","value":0.892,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-r-one-9-3-handguard f4a8b5638442 (Aero's gallery: the R-ONE's left side (its rear at the picture's right), mirrored, 1000 x 630)","scaleRef":"its top rail teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 37.576 px a tooth, 95.37 px/in","method":"the longest see-through slot in the four rows","via":"harvest"}}]},"rear_x":{"label":"The handguard's rear end (its two side tabs' ends) against the receiver's front face (negative: behind it)","kind":"length","measurements":[{"id":"family","value":-0.763,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rear_x}","via":"harvest"}}],"note":"The clamp is the family's: the 15 in's place by reference. On this length's view the first tooth's rear face is 0.503 in ahead of the tabs' ends (the 15 in's, read the same way, 0.517); and Aero's length, back from the rail's end, puts the receiver's face 0.273 in ahead of them where the 15 in's puts it 0.318: within what a length stated to a tenth (0.05) and the two readings (0.02 each) carry."},"rail_top_above_bore":{"label":"Its rail's top above the bore (level with the receiver's)","kind":"length","measurements":[{"id":"family","value":1.2125,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rail_top_above_bore}","via":"harvest"}}]},"width":{"label":"The R-ONE family: the 15 in's width","kind":"length","measurements":[{"id":"family","value":1.5,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.width}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"height":{"label":"The R-ONE family: the 15 in's height","kind":"length","measurements":[{"id":"family","value":1.95,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.height}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"inside_diameter":{"label":"The R-ONE family: the 15 in's inside diameter","kind":"length","measurements":[{"id":"family","value":1.3,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.inside_diameter}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"inside_height":{"label":"The R-ONE family: the 15 in's inside height","kind":"length","measurements":[{"id":"family","value":1.65,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.inside_height}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"bottom_flat_width":{"label":"The R-ONE family: the 15 in's bottom flat width","kind":"length","measurements":[{"id":"family","value":0.609,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.bottom_flat_width}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"side_top_width":{"label":"The R-ONE family: the 15 in's side top width","kind":"length","measurements":[{"id":"family","value":1.455,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.side_top_width}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"lower_edge_width":{"label":"The R-ONE family: the 15 in's lower edge width","kind":"length","measurements":[{"id":"family","value":1.133,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.lower_edge_width}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"lower_edge_below_rail_top":{"label":"The R-ONE family: the 15 in's lower edge below rail top","kind":"length","measurements":[{"id":"family","value":1.759,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.lower_edge_below_rail_top}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"rail_neck_width":{"label":"The R-ONE family: the 15 in's rail neck width","kind":"length","measurements":[{"id":"family","value":0.62,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rail_neck_width}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"rail_neck_foot_below_rail_top":{"label":"The R-ONE family: the 15 in's rail neck foot below rail top","kind":"length","measurements":[{"id":"family","value":0.377,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rail_neck_foot_below_rail_top}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"rail_centre_gap":{"label":"The R-ONE family: the 15 in's rail centre gap","kind":"length","measurements":[{"id":"family","value":0.365,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rail_centre_gap}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"rail_window_length":{"label":"The R-ONE family: the 15 in's rail window length","kind":"length","measurements":[{"id":"family","value":0.54,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rail_window_length}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"rail_bridge_recess":{"label":"The R-ONE family: the 15 in's rail bridge recess","kind":"length","measurements":[{"id":"family","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rail_bridge_recess}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"side_flat_top_below_rail_top":{"label":"The R-ONE family: the 15 in's side flat top below rail top","kind":"length","measurements":[{"id":"family","value":0.88,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.side_flat_top_below_rail_top}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"side_flat_bottom_below_rail_top":{"label":"The R-ONE family: the 15 in's side flat bottom below rail top","kind":"length","measurements":[{"id":"family","value":1.502,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.side_flat_bottom_below_rail_top}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"thin_slot_width":{"label":"The R-ONE family: the 15 in's thin slot width","kind":"length","measurements":[{"id":"family","value":0.22,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.thin_slot_width}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"thin_slot_row_a_y":{"label":"The R-ONE family: the 15 in's thin slot row a y","kind":"length","measurements":[{"id":"family","value":0.71,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.thin_slot_row_a_y}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"thin_slot_row_b_y":{"label":"The R-ONE family: the 15 in's thin slot row b y","kind":"length","measurements":[{"id":"family","value":0.46,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.thin_slot_row_b_y}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"thin_slot_row_d_y":{"label":"The R-ONE family: the 15 in's thin slot row d y","kind":"length","measurements":[{"id":"family","value":-0.41,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.thin_slot_row_d_y}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"thin_slot_row_e_y":{"label":"The R-ONE family: the 15 in's thin slot row e y","kind":"length","measurements":[{"id":"family","value":-0.635,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.thin_slot_row_e_y}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"qd_socket_d":{"label":"The R-ONE family: the 15 in's qd socket d","kind":"length","measurements":[{"id":"family","value":0.37,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.qd_socket_d}","via":"harvest"}}],"note":"The R-ONE's section and what is cut in it the same way at every length, by reference to the 15 in's ledger: Aero sells the R-ONE as one product in seven lengths (its configurable page) and its own pages give every length the one inside and outside diameter (\"1.3\\\" Inside diameter\", \"1.5\\\" Outside diameter\"). An assumption: no view of this length's end is on file. This length's side view agrees in height (2.14 to 2.15 in with the clamp, the 15 in's 2.13)."},"reach_inside":{"label":"The room inside its side faces before the barrel, at the M-LOK slots (what an accessory's nuts may take)","kind":"length","measurements":[],"note":"Not read: as on the 15 in, it depends on the barrel under it."}}},{"subject":"aero-s-one-15-handguard","title":"Aero Precision AR15 15 in S-ONE M-LOK handguard (APRA500105A)","dimensions":{"weight":{"label":"Weight (the handguard alone; its barrel nut, taper lock nuts and screw aren't counted: hardware_weight)","kind":"mass","measurements":[{"id":"aero","value":7.95,"unit":"oz","pm":0.005,"stated":"Weight(s) 7.95 oz","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, AR15 15\" S-ONE M-LOK Handguard - Anodized Black (APRA500105A), Specifications","url":"https://www.aeroprecisionusa.com/ar15-15-atlas-s-one-m-lok-handguard-anodized-black","retrieved":"2026-10-13","via":"harvest"}},{"id":"aero-list","value":7.95,"unit":"oz","pm":0.005,"stated":"M-LOK Handguard Weights: 7.3\" - 4.86 oz / 9.3\" - 5.47 oz / 10.3\" - 6.0 oz / 12.7\" - 7.00 oz / 15\" - 7.95 oz","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, AR15 15\" S-ONE M-LOK Handguard - Anodized Black (APRA500105A), Details, \"Lightweight By Design\"","url":"https://www.aeroprecisionusa.com/ar15-15-atlas-s-one-m-lok-handguard-anodized-black","retrieved":"2026-10-13","via":"harvest"}},{"id":"wing-tactical","value":7.95,"unit":"oz","pm":0.005,"stated":"Weight: 7-Inch: 4.86 oz. 9-Inch: 5.47 oz. 12-Inch: 7 oz. 15-Inch: 7.95 oz.","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Aero Precision ATLAS S-ONE M-LOK Free Float Handguard (one page for every length and colour), Specifications","url":"https://www.wingtactical.com/firearm-parts-accessories/aero-precision-atlas-s-one-m-lok-handguard/","retrieved":"2026-10-13","via":"harvest"}},{"id":"ar15discounts","value":7.95,"unit":"oz","pm":0.005,"stated":"weighing just 7.95 oz for the handguard alone","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, Aero Precision AR-15 15\" ATLAS S-ONE M-LOK Handguard - Anodized Black - BLEM (APRA500105BA: the blemished one, a number of its own)","url":"https://ar15discounts.com/products/aero-precision-ar-15-15-atlas-s-one-m-lok-handguard-anodized-black-blem/","retrieved":"2026-10-13","via":"harvest"}}],"adopt":{"from":"aero","reason":"The maker's specification row for this part; its own list of every length, a seller's table and a second seller's page say the same."},"note":"The handguard as its page pictures it: no nut, wedge or screw in it. The model's volume as 6061 aluminium is held to this (app/tests/aero-s-one-15-handguard.test.ts)."},"hardware_weight":{"label":"Its mounting hardware's weight (the barrel nut, the two taper lock nuts and the turnbuckle screw; not in the build's weight)","kind":"mass","measurements":[{"id":"aero","value":1.9,"unit":"oz","pm":0.05,"stated":"Mounting Hardware Weight: 1.9 oz (same across all S-ONE Handguard options)","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, AR15 15\" S-ONE M-LOK Handguard - Anodized Black (APRA500105A), Details, \"Lightweight By Design\"","url":"https://www.aeroprecisionusa.com/ar15-15-atlas-s-one-m-lok-handguard-anodized-black","retrieved":"2026-10-13","via":"harvest"}},{"id":"kygunco","value":1.9,"unit":"oz","pm":0.05,"stated":"Mounting Hardware Weight: 1.9 oz (same across all S-ONE Handguard options)","source":{"type":"spec","publisher":"retailer","name":"KYGUNCO, AERO PRECISION ATLAS S-One 15\" M-LOK AR15 Handguard | Anodized Black (Style RPR-APRA500105A, UPC 815421021042)","url":"https://www.kygunco.com/product/aero-precision-apra500105a-ar15-15-atlas-s-one-m-lok-handguard-ano","retrieved":"2026-10-13","via":"harvest"},"note":"The maker's sentence on a seller's page."},{"id":"wing-tactical","value":4.72,"unit":"oz","pm":0.005,"stated":"Mounting Hardware: 4.72 oz.","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Aero Precision ATLAS S-ONE M-LOK Free Float Handguard (one page for every length and colour), Specifications","url":"https://www.wingtactical.com/firearm-parts-accessories/aero-precision-atlas-s-one-m-lok-handguard/","retrieved":"2026-10-13","via":"harvest"},"note":"The same table lists what comes with it: \"1x Barrel Nut 1x Barrel Nut Wrench 1x Mounting Hardware Kit\". It doesn't say which of them the 4.72 oz weighs."}],"adopt":{"from":"aero","reason":"The maker's own page for this part, which a seller restates. The 4.72 oz of one seller's table (and of another's total) is two and a half times it and may count the wrench and the shims that come in the bag: neither page says. Kept as a conflict; neither figure is in the build's weight."},"note":"Three pages, two figures. AR15Discounts' page for the blemished one says \"Weight: Approximately 12.67 oz (including hardware)\" (weight_with_hardware), which is the handguard's 7.95 and Wing Tactical's 4.72 together. Nobody's scale reading is on file. Aero's page for the R-ONE of this length lists 4.72 oz where its R-ONE parent page lists 1.9."},"weight_with_hardware":{"label":"Weight with its hardware, by one seller","kind":"mass","measurements":[{"id":"ar15discounts","value":12.67,"unit":"oz","pm":0.005,"stated":"Weight: Approximately 12.67 oz (including hardware)","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, Aero Precision AR-15 15\" ATLAS S-ONE M-LOK Handguard - Anodized Black - BLEM (APRA500105BA: the blemished one, a number of its own)","url":"https://ar15discounts.com/products/aero-precision-ar-15-15-atlas-s-one-m-lok-handguard-anodized-black-blem/","retrieved":"2026-10-13","via":"harvest"}}],"note":"A seller's figure for the blemished one: 7.95 with 4.72. Not used: the build's weight is the handguard's."},"length":{"label":"Length (the receiver's face to the end of the last rail slot)","kind":"length","measurements":[{"id":"aero","value":15,"unit":"in","pm":0.05,"stated":"Handguard Length 15\"","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, AR15 15\" S-ONE M-LOK Handguard - Anodized Black (APRA500105A), Specifications","url":"https://www.aeroprecisionusa.com/ar15-15-atlas-s-one-m-lok-handguard-anodized-black","retrieved":"2026-10-13","via":"harvest"}},{"id":"aero-description","value":14.94,"unit":"in","pm":0.005,"stated":"Available in M-LOK profiles with 7.3\", 9.3\", 10.3\", 12.7\" and 14.94\" options.","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, AR15 15\" S-ONE M-LOK Handguard - Anodized Black (APRA500105A), Details","url":"https://www.aeroprecisionusa.com/ar15-15-atlas-s-one-m-lok-handguard-anodized-black","retrieved":"2026-10-13","via":"harvest"}},{"id":"wing-tactical","value":14.94,"unit":"in","pm":0.005,"stated":"Actual Length (When Installed): 7-Inch: 7.25\" 9-Inch: 9.19\" 12-Inch: 12.56\" 15-Inch: 14.94\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Aero Precision ATLAS S-ONE M-LOK Free Float Handguard (one page for every length and colour), Specifications","url":"https://www.wingtactical.com/firearm-parts-accessories/aero-precision-atlas-s-one-m-lok-handguard/","retrieved":"2026-10-13","via":"harvest"},"note":"A seller's table; it doesn't say between what its installed length is taken."},{"id":"photo","value":15.025,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-s-one-15-handguard 3c7e1b901211 and 44cb3b093489 (Sportsman's Warehouse's 1200 px copies of Aero's two gallery views of APRA500105A: its right side and its left)","scaleRef":"the view's own eight rail slots, four at each end, on one grid of the standard's pitch (std.picatinny.slot_pitch, .394) 36 pitches from the first to the last: a quadratic from pixels to inches through their centres, each within 0.002 in of it (74.7 px/in at the rear slot rising to 76.5 at the front in the right view, 75.5 falling to 74.8 in the left)","method":"its rail's body from its rear face (where the outline's top steps up to the slots' floors, behind the first tooth) to its front end (the last tooth's front face in the band of the tooth tops): 15.026 in the right view, 15.025 in the left (.cache/batch8/aero-s-one-15-handguard/read.py: rail_front_from_rear less rail_rear_face_from_rear)","via":"harvest"}}],"adopt":{"from":"aero","reason":"The maker's specification row, with its own rule for what the length spans; on both of its side views the rail runs 15.03 in from its rear face to its front end. The 14.94 of the same page's description and of a seller's table is 0.06 under: taken as the span, it would put the rail's rear face 0.09 in inside the receiver's front shoulder."},"note":"Aero says what its lengths are between, on this page: \"Actual Handguard Lengths 7.3\", 9.3\", 10.3\", 12.7\", 15\" Aero Precision rail lengths measure from end to end. This is the point of contact at the receiver to the end of the last picatinny slot at the muzzle.\" The same page says 15\" twice in its specification and 14.94\" once in its description."},"width":{"label":"Width across its side faces at their lower edges, where it is widest (the maker's \"outside diameter\")","kind":"length","measurements":[{"id":"aero","value":1.5,"unit":"in","pm":0.05,"stated":"1.5\" Outside diameter","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, AR15 15\" S-ONE M-LOK Handguard - Anodized Black (APRA500105A), Features","url":"https://www.aeroprecisionusa.com/ar15-15-atlas-s-one-m-lok-handguard-anodized-black","retrieved":"2026-10-13","via":"harvest"}},{"id":"wing-tactical","value":1.51,"unit":"in","pm":0.005,"stated":"Outside Diameter: Height: 1.95\" Width: 1.51\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Aero Precision ATLAS S-ONE M-LOK Free Float Handguard (one page for every length and colour), Specifications","url":"https://www.wingtactical.com/firearm-parts-accessories/aero-precision-atlas-s-one-m-lok-handguard/","retrieved":"2026-10-13","via":"harvest"}}],"adopt":{"from":"aero","reason":"The maker's, to one place; a seller's table of the family says 1.51."}},"height":{"label":"Height (its rail's top to its bottom flat, along the body)","kind":"length","measurements":[{"id":"wing-tactical","value":1.95,"unit":"in","pm":0.005,"stated":"Outside Diameter: Height: 1.95\" Width: 1.51\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Aero Precision ATLAS S-ONE M-LOK Free Float Handguard (one page for every length and colour), Specifications","url":"https://www.wingtactical.com/firearm-parts-accessories/aero-precision-atlas-s-one-m-lok-handguard/","retrieved":"2026-10-13","via":"harvest"}},{"id":"photo","value":1.95,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-s-one-15-handguard 3c7e1b901211 and 44cb3b093489 (Sportsman's Warehouse's 1200 px copies of Aero's two gallery views of APRA500105A: its right side and its left)","scaleRef":"the view's own eight rail slots, four at each end, on one grid of the standard's pitch (std.picatinny.slot_pitch, .394) 36 pitches from the first to the last: a quadratic from pixels to inches through their centres, each within 0.002 in of it (74.7 px/in at the rear slot rising to 76.5 at the front in the right view, 75.5 falling to 74.8 in the left); down the picture at the scale of the middle of the rail (75.56 px/in right, 75.14 left)","method":"the teeth's tops to the body's last dark row, away from the clamp: 147.3 rows in the right view (1.949), 146.6 in the left (1.952) (.cache/batch8/aero-s-one-15-handguard/read.py). The clamp's end reaches 2.13 (2.130, 2.122)","via":"harvest"}}],"adopt":{"from":"wing-tactical","reason":"A seller's table of the maker's sizes, to two places, which gives height and width apart; both side views read 1.95 at their own rail's scale."},"note":"The body's; the clamp at the receiver's end is deeper (2.13). The maker gives no height."},"inside_diameter":{"label":"Inside width (the maker's \"inside diameter\")","kind":"length","measurements":[{"id":"aero","value":1.3,"unit":"in","pm":0.05,"stated":"1.3\" Inside diameter","source":{"type":"spec","publisher":"manufacturer","name":"Aero Precision, AR15 15\" S-ONE M-LOK Handguard - Anodized Black (APRA500105A), Features","url":"https://www.aeroprecisionusa.com/ar15-15-atlas-s-one-m-lok-handguard-anodized-black","retrieved":"2026-10-13","via":"harvest"}},{"id":"wing-tactical","value":1.3,"unit":"in","pm":0.05,"stated":"Inside Diameter: Height: 1.65\" Width: 1.3\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Aero Precision ATLAS S-ONE M-LOK Free Float Handguard (one page for every length and colour), Specifications","url":"https://www.wingtactical.com/firearm-parts-accessories/aero-precision-atlas-s-one-m-lok-handguard/","retrieved":"2026-10-13","via":"harvest"}}],"adopt":{"from":"aero","reason":"The maker's; the seller's table agrees."}},"inside_height":{"label":"Inside height (its floor to the underside of its rail, under its two rail blocks)","kind":"length","measurements":[{"id":"wing-tactical","value":1.65,"unit":"in","pm":0.005,"stated":"Inside Diameter: Height: 1.65\" Width: 1.3\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Aero Precision ATLAS S-ONE M-LOK Free Float Handguard (one page for every length and colour), Specifications","url":"https://www.wingtactical.com/firearm-parts-accessories/aero-precision-atlas-s-one-m-lok-handguard/","retrieved":"2026-10-13","via":"harvest"}}],"note":"One seller's table, for every length of the S-ONE; it is taken as the R-ONE's is (the same table's figure there): the floor to the top of the arched channel under the rail. Between the two rail blocks the top is 0.24 lower, and the inside's roof there isn't seen (the model's approximations)."},"overall_length":{"label":"Overall length, end to end","kind":"length","measurements":[{"id":"photo","value":15.35,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-s-one-15-handguard 3c7e1b901211 and 44cb3b093489 (Sportsman's Warehouse's 1200 px copies of Aero's two gallery views of APRA500105A: its right side and its left)","scaleRef":"the view's own eight rail slots, four at each end, on one grid of the standard's pitch (std.picatinny.slot_pitch, .394) 36 pitches from the first to the last: a quadratic from pixels to inches through their centres, each within 0.002 in of it (74.7 px/in at the rear slot rising to 76.5 at the front in the right view, 75.5 falling to 74.8 in the left)","method":"the silhouette's two ends on the rows of the body: 15.357 in the right view, 15.349 in the left (.cache/batch8/aero-s-one-15-handguard/read.py)","via":"harvest"}}],"note":"Aero's 15 in runs from the receiver to the end of the last rail slot; the two tabs at its rear reach back past the receiver's shoulder, and its front end is 0.03 past its rail's."},"rail_front_from_rear":{"label":"Its rail's front end (the end of the last slot's lug) ahead of the outline's rear end","kind":"length","measurements":[{"id":"photo","value":15.321,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-s-one-15-handguard 3c7e1b901211 and 44cb3b093489 (Sportsman's Warehouse's 1200 px copies of Aero's two gallery views of APRA500105A: its right side and its left)","scaleRef":"the view's own eight rail slots, four at each end, on one grid of the standard's pitch (std.picatinny.slot_pitch, .394) 36 pitches from the first to the last: a quadratic from pixels to inches through their centres, each within 0.002 in of it (74.7 px/in at the rear slot rising to 76.5 at the front in the right view, 75.5 falling to 74.8 in the left)","method":"the last tooth's front face in the band of the tooth tops: 15.327 from the outline's rear end in the right view, 15.315 in the left","via":"harvest"}}]},"rail_rear_face_from_rear":{"label":"Its rail's rear face (where the rail's body begins, at the slots' floors' height) ahead of the outline's rear end","kind":"length","measurements":[{"id":"photo","value":0.296,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-s-one-15-handguard 3c7e1b901211 and 44cb3b093489 (Sportsman's Warehouse's 1200 px copies of Aero's two gallery views of APRA500105A: its right side and its left)","scaleRef":"the view's own eight rail slots, four at each end, on one grid of the standard's pitch (std.picatinny.slot_pitch, .394) 36 pitches from the first to the last: a quadratic from pixels to inches through their centres, each within 0.002 in of it (74.7 px/in at the rear slot rising to 76.5 at the front in the right view, 75.5 falling to 74.8 in the left)","method":"where the outline's top steps up from the tabs' (0.42 below the rail's top) to the slots' floors' height: 0.301 ahead of the rear end in the right view, 0.290 in the left. The underside steps down to the clamp's 0.36 ahead of the rear end","via":"harvest"}}],"note":"What meets the receiver: the two tabs behind it reach back along the receiver's front ring (Wing Tactical: \"Built-in anti-rotation tabs\"; Aero: \"indexing tabs\")."},"rail_slot0_from_rear":{"label":"Its rear rail block's first slot (its centre) ahead of the outline's rear end","kind":"length","measurements":[{"id":"photo","value":0.82,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-s-one-15-handguard 3c7e1b901211 and 44cb3b093489 (Sportsman's Warehouse's 1200 px copies of Aero's two gallery views of APRA500105A: its right side and its left)","scaleRef":"the view's own eight rail slots, four at each end, on one grid of the standard's pitch (std.picatinny.slot_pitch, .394) 36 pitches from the first to the last: a quadratic from pixels to inches through their centres, each within 0.002 in of it (74.7 px/in at the rear slot rising to 76.5 at the front in the right view, 75.5 falling to 74.8 in the left)","method":"the outline's rear end on the rows of the body, 0.829 behind the first slot's centre in the right view and 0.812 in the left; a slot's centre is the middle of the gap between two teeth at the 50% level (.cache/batch8/aero-s-one-15-handguard/read.py)","via":"harvest"}}],"note":"The ± is the two views' spread. The rear end is a silhouette's (the near tab's end, nearer the lens than the rail's middle), and nothing rests on it: where the grid stands on a rifle is counted back from the rail's front end (rear_x), the same two readings apart."},"rail_rear_slots":{"label":"Slots in its rear rail block","kind":"count","measurements":[{"id":"photo","value":4,"unit":"count","source":{"type":"photo","photo":"references/aero-s-one-15-handguard 3c7e1b901211 and 44cb3b093489 (Sportsman's Warehouse's 1200 px copies of Aero's two gallery views of APRA500105A: its right side and its left)","scaleRef":"counted","method":"the gaps between the five teeth at the receiver's end, in the band of the tooth tops, in both views: 4. Wing Tactical's view from the receiver's end (5bea74f955a3) shows the same five lugs","via":"harvest"}}],"note":"Aero: \"Front and rear picatinny rail\"; \"Eliminated center of top rail for weight reduction\". Behind the first tooth the rail's body runs on at the floors' height for 0.2 in (a land, not counted)."},"rail_front_slots":{"label":"Slots in its front rail block","kind":"count","measurements":[{"id":"photo","value":4,"unit":"count","source":{"type":"photo","photo":"references/aero-s-one-15-handguard 3c7e1b901211 and 44cb3b093489 (Sportsman's Warehouse's 1200 px copies of Aero's two gallery views of APRA500105A: its right side and its left)","scaleRef":"counted","method":"the gaps between the five teeth at the muzzle end, in the band of the tooth tops, in both views: 4","via":"harvest"}}]},"rail_front_slot0_from_slot0":{"label":"Its front rail block's first slot ahead of its rear block's first (centre to centre)","kind":"length","measurements":[{"id":"grid","value":13.002,"unit":"in","source":{"type":"derived","expr":"33 * {std.picatinny.slot_pitch}","via":"harvest"},"note":"The two blocks are on one grid of the standard's pitch, the front block's four slots its 33rd to 36th. Read on both side views (references/aero-s-one-15-handguard 3c7e1b901211 and 44cb3b093489 (Sportsman's Warehouse's 1200 px copies of Aero's two gallery views of APRA500105A: its right side and its left)): at the scale each block's own four slots give (74.78 px/in at the rear block and 76.50 at the front in the right view, 75.67 and 74.91 in the left), the rear block's first slot to the front block's last is 35.96 pitches in the right view and 35.94 in the left; and fitted together, all eight centres are within 0.002 in of that grid in each view (.cache/batch8/aero-s-one-15-handguard/read.py)."}],"note":"The rail the R-ONE of this length has 37 slots of, with the 29 between left off."},"rail_block_rear_flat_end_from_slot0":{"label":"Where the rear block's top begins to fall to the spine, ahead of its first slot","kind":"length","measurements":[{"id":"photo","value":1.46,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-s-one-15-handguard 3c7e1b901211 and 44cb3b093489 (Sportsman's Warehouse's 1200 px copies of Aero's two gallery views of APRA500105A: its right side and its left)","scaleRef":"the view's own eight rail slots, four at each end, on one grid of the standard's pitch (std.picatinny.slot_pitch, .394) 36 pitches from the first to the last: a quadratic from pixels to inches through their centres, each within 0.002 in of it (74.7 px/in at the rear slot rising to 76.5 at the front in the right view, 75.5 falling to 74.8 in the left)","method":"the outline's top leaves the rail's top between 1.44 and 1.49 ahead of the first slot in both views (0.008 down at 1.440, 0.026 at 1.494 right; 0.002 at 1.439, 0.029 at 1.492 left)","via":"harvest"}}]},"rail_ramp_rear_foot_from_slot0":{"label":"Where the rear block's ramp reaches the spine, ahead of its first slot","kind":"length","measurements":[{"id":"photo","value":1.95,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-s-one-15-handguard 3c7e1b901211 and 44cb3b093489 (Sportsman's Warehouse's 1200 px copies of Aero's two gallery views of APRA500105A: its right side and its left)","scaleRef":"the view's own eight rail slots, four at each end, on one grid of the standard's pitch (std.picatinny.slot_pitch, .394) 36 pitches from the first to the last: a quadratic from pixels to inches through their centres, each within 0.002 in of it (74.7 px/in at the rear slot rising to 76.5 at the front in the right view, 75.5 falling to 74.8 in the left)","method":"the outline's top is within 0.01 of the spine's height from 1.92 to 1.98 ahead of the first slot (0.239 down at 1.921 and 0.245 at 1.975 right; 0.235 at 1.916, 0.237 at 1.969 left). Between, it falls in an S: 0.065 down at 1.547, 0.140 at 1.654, 0.195 at 1.761, 0.229 at 1.868","via":"harvest"}}]},"rail_ramp_front_foot_from_slot0":{"label":"Where the front block's ramp leaves the spine, ahead of the rear block's first slot","kind":"length","measurements":[{"id":"photo","value":12.27,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-s-one-15-handguard 3c7e1b901211 and 44cb3b093489 (Sportsman's Warehouse's 1200 px copies of Aero's two gallery views of APRA500105A: its right side and its left)","scaleRef":"the view's own eight rail slots, four at each end, on one grid of the standard's pitch (std.picatinny.slot_pitch, .394) 36 pitches from the first to the last: a quadratic from pixels to inches through their centres, each within 0.002 in of it (74.7 px/in at the rear slot rising to 76.5 at the front in the right view, 75.5 falling to 74.8 in the left)","method":"the outline's top begins to rise at 12.25 to 12.31 (0.234 down at 12.245 and 0.227 at 12.297 right; 0.237 at 12.243, 0.233 at 12.297 left); 0.170 down at 12.455, 0.105 at 12.560, 0.030 at 12.665","via":"harvest"}}]},"rail_block_front_flat_start_from_slot0":{"label":"Where the front block's top is reached, ahead of the rear block's first slot","kind":"length","measurements":[{"id":"photo","value":12.72,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-s-one-15-handguard 3c7e1b901211 and 44cb3b093489 (Sportsman's Warehouse's 1200 px copies of Aero's two gallery views of APRA500105A: its right side and its left)","scaleRef":"the view's own eight rail slots, four at each end, on one grid of the standard's pitch (std.picatinny.slot_pitch, .394) 36 pitches from the first to the last: a quadratic from pixels to inches through their centres, each within 0.002 in of it (74.7 px/in at the rear slot rising to 76.5 at the front in the right view, 75.5 falling to 74.8 in the left)","method":"the outline's top reaches the rail's top at 12.727 in the right view (0.001 down) and 12.73 in the left (0.010 down at 12.734)","via":"harvest"}}]},"spine_below_rail_top":{"label":"The spine's top between the two rail blocks, below the rail's top","kind":"length","measurements":[{"id":"photo","value":0.242,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aero-s-one-15-handguard 3c7e1b901211 and 44cb3b093489 (Sportsman's Warehouse's 1200 px copies of Aero's two gallery views of APRA500105A: its right side and its left)","scaleRef":"the view's own eight rail slots, four at each end, on one grid of the standard's pitch (std.picatinny.slot_pitch, .394) 36 pitches from the first to the last: a quadratic from pixels to inches through their centres, each within 0.002 in of it (74.7 px/in at the rear slot rising to 76.5 at the front in the right view, 75.5 falling to 74.8 in the left); down the picture at the scale of the middle of the rail","method":"the outline's top between the ribs, median over its length: 18.3 rows under the teeth's tops in both views (0.243 right, 0.241 left)","via":"harvest"}}],"note":"Wing Tactical: \"Eliminated center of top rail for weight reduction\"."},"spine_width":{"label":"The spine's top, across","kind":"length","measurements":[{"id":"end","value":0.62,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-s-one-15-handguard 5bea74f955a3 (Wing Tactical's gallery: an S-ONE from its receiver end, looking forward along its top, its barrel nut in it; the page is for every length and doesn't say which this is)","scaleRef":"the rear rail block's head at the standard's .835 across its widest (std.picatinny.top_width), which shows on its first tooth's rear face: 295.5 px on rows 494 to 500, 353.9 px/in there; the front block's head, 13.0 in further off, is 148 px across, which puts the lens 13.0 in from that tooth; the spine's rear end is 2.3 in further off: 301 px/in","method":"the spine's top where it leaves the rear block's ramp: 187 px across (.cache/batch8/aero-s-one-15-handguard/endcrops.py, end-top.png)","via":"harvest"}}],"note":"As wide as the neck the rail blocks stand on (rail_neck_width, 0.594) within what the two readings carry: the spine is drawn as that neck cut down to a flat top."},"spine_roof_below_rail_top":{"label":"The inside's roof under the spine, below the rail's top","kind":"length","measurements":[{"id":"midway","value":0.2922,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"({.spine_below_rail_top} + {.rail_top_above_bore} - {std.ar15.gas_tube_above_bore} - {aero-mid-gas-tube.od} / 2) / 2","via":"harvest"},"note":"Not read: no view on file shows the inside under the spine. It lies between two things that are sourced: the spine's top (0.242 under the rail's top) and the top of a gas tube's rear run, which passes under the spine's rear end 0.3425 under the rail's top (the standard's height for the tube above the bore and half a tube's diameter over it). The roof is drawn midway: a twentieth of an inch of metal over it and a twentieth of room under it. The ± is all the room there is either way."}],"note":"An assumption with two sourced bounds, listed in the part's approximations. The published wall (a tenth, from the two widths) can't be the roof's thickness here: a tenth under the spine's top is the tube's top."},"rib_height":{"label":"A rib across the spine: its top above the spine's","kind":"length","measurements":[{"id":"photo","value":0.03,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/aero-s-one-15-handguard 3c7e1b901211 and 44cb3b093489 (Sportsman's Warehouse's 1200 px copies of Aero's two gallery views of APRA500105A: its right side and its left)","scaleRef":"the view's own eight rail slots, four at each end, on one grid of the standard's pitch (std.picatinny.slot_pitch, .394) 36 pitches from the first to the last: a quadratic from pixels to inches through their centres, each within 0.002 in of it (74.7 px/in at the rear slot rising to 76.5 at the front in the right view, 75.5 falling to 74.8 in the left); down the picture at the scale of the middle of the rail","method":"the nine bumps of the outline's top between the blocks: 0.028 to 0.032 high in the right view, 0.027 to 0.031 in the left","via":"harvest"}}],"note":"Aero: \"Indexing grooves in 12:00 position for positive grip control\"."},"rib_length":{"label":"A rib across the spine: its length along the handguard","kind":"length","measurements":[{"id":"photo","value":0.15,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-s-one-15-handguard 3c7e1b901211 and 44cb3b093489 (Sportsman's Warehouse's 1200 px copies of Aero's two gallery views of APRA500105A: its right side and its left)","scaleRef":"the view's own eight rail slots, four at each end, on one grid of the standard's pitch (std.picatinny.slot_pitch, .394) 36 pitches from the first to the last: a quadratic from pixels to inches through their centres, each within 0.002 in of it (74.7 px/in at the rear slot rising to 76.5 at the front in the right view, 75.5 falling to 74.8 in the left)","method":"where the outline's top stands more than 0.01 above the spine's: 0.16 to 0.19 long in the right view, 0.13 to 0.15 in the left","via":"harvest"}}]},"rib_count":{"label":"Ribs across the spine","kind":"count","measurements":[{"id":"photo","value":9,"unit":"count","source":{"type":"photo","photo":"references/aero-s-one-15-handguard 3c7e1b901211 and 44cb3b093489 (Sportsman's Warehouse's 1200 px copies of Aero's two gallery views of APRA500105A: its right side and its left)","scaleRef":"counted","method":"the bumps of the outline's top between the two ramps, in both views: 9, a thin slot's pitch apart, each over the bar between two thin slots (their middles 2.69 to 11.23 ahead of the rail's first slot; the bars' are 2.70 to 11.23). The bars at each end of the row are under the ramps' feet","via":"harvest"}}]},"rear_x":{"label":"The handguard's rear end (its two tabs' ends) against the receiver's front face (negative: behind it)","kind":"length","measurements":[{"id":"derived","value":-0.766,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"0in - {std.ar15.upper_barrel_thread_length} - ({.rail_front_from_rear} - {.length})","via":"harvest"},"note":"Aero's rule for its length (\"the point of contact at the receiver to the end of the last picatinny slot at the muzzle\"): 15 in back from the rail's front end is 0.321 ahead of the tabs' ends, at the receiver's front shoulder, where its barrel-nut thread begins."},{"id":"rail-face","value":-0.741,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"0in - {std.ar15.upper_barrel_thread_length} - {.rail_rear_face_from_rear}","via":"harvest"},"note":"The rail's own rear face, as its side views have it, on the receiver's front shoulder: 0.025 from the rule's."}],"adopt":{"from":"derived","reason":"The maker's own rule for its length on its own side views; the rail's rear face read on the same views lands within 0.025 in of the receiver's shoulder."},"note":"No photo of this handguard on a receiver is on file (KYGUNCO's picture of the complete upper APAR700305M7 is on a host whose robots.txt answers 400: left alone)."},"rail_top_above_bore":{"label":"Its rail's top above the bore axis","kind":"length","measurements":[{"id":"level","value":1.2125,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-m4e1-threaded-upper.rail_top_above_pin} - {aero-m4e1-threaded-upper.bore_axis_above_pin}","via":"harvest"}}],"note":"Level with the receiver's rail. Aero, this page: \"ATLAS Handguards are designed to match seamlessly with our M4E1 Threaded Upper Receivers.\" Its page for that upper says its picatinny profile \"blends seamlessly with our R-ONE, S-ONE and Enhanced Handguards\". So the receiver's rail top above the pin line less the bore's height above it."},"side_flat_top_below_rail_top":{"label":"Its side faces' upper edge, below the rail's top","kind":"length","measurements":[{"id":"sides","value":0.885,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-s-one-15-handguard 3c7e1b901211 and 44cb3b093489 (Sportsman's Warehouse's 1200 px copies of Aero's two gallery views of APRA500105A: its right side and its left)","scaleRef":"the view's own eight rail slots, four at each end, on one grid of the standard's pitch (std.picatinny.slot_pitch, .394) 36 pitches from the first to the last: a quadratic from pixels to inches through their centres, each within 0.002 in of it (74.7 px/in at the rear slot rising to 76.5 at the front in the right view, 75.5 falling to 74.8 in the left); down the picture at the scale of the middle of the rail","method":"the tone down the solid bars between its openings (4.85 and 8.02 ahead of the rail's first slot, where a thin slot's bar and an M-LOK bar are one): the upper face's (70 to 110) gives way to the side face's even tone (36 to 38 right, 46 to 48 left) between 0.87 and 0.90 in all four columns (.cache/batch8/aero-s-one-15-handguard/levels.py)","via":"harvest"}},{"id":"r-one","value":0.88,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.side_flat_top_below_rail_top}","via":"harvest"},"note":"The R-ONE's, read the same way on its own side views."}],"adopt":{"from":"sides","reason":"This handguard's own side views; the R-ONE's reads the same within 0.005."}},"side_flat_bottom_below_rail_top":{"label":"Its side faces' lower edge, below the rail's top","kind":"length","measurements":[{"id":"sides","value":1.51,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-s-one-15-handguard 3c7e1b901211 and 44cb3b093489 (Sportsman's Warehouse's 1200 px copies of Aero's two gallery views of APRA500105A: its right side and its left)","scaleRef":"the view's own eight rail slots, four at each end, on one grid of the standard's pitch (std.picatinny.slot_pitch, .394) 36 pitches from the first to the last: a quadratic from pixels to inches through their centres, each within 0.002 in of it (74.7 px/in at the rear slot rising to 76.5 at the front in the right view, 75.5 falling to 74.8 in the left); down the picture at the scale of the middle of the rail","method":"the same four columns: the side face's even tone ends between 1.50 and 1.53 (.cache/batch8/aero-s-one-15-handguard/levels.py)","via":"harvest"}},{"id":"r-one","value":1.502,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.side_flat_bottom_below_rail_top}","via":"harvest"},"note":"The R-ONE's, read on the view square on to its muzzle end."}],"adopt":{"from":"sides","reason":"This handguard's own side views; the R-ONE's end view reads 0.008 from it."}},"side_top_width":{"label":"Width across its side faces at their upper edges","kind":"length","measurements":[{"id":"r-one","value":1.455,"unit":"in","source":{"type":"derived","expr":"{aero-r-one-15-handguard.side_top_width}","via":"harvest"},"note":"Read on the R-ONE's view square on to its muzzle end (its ledger says how). The S-ONE is the same series with the middle of its rail taken off (Aero's Series row for both: \"R-ONE/S-ONE\"; Wing Tactical's table gives both the same four section figures, outside 1.95 by 1.51 and inside 1.65 by 1.3), no view square on to an S-ONE's end is on file, and its own views show the same faces: flat side faces a little nearer each other at their tops (5bea74f955a3, 5a32198025ae)."}],"note":"Not this handguard's own reading: the R-ONE's figure by reference. A view square on to an S-ONE's end would replace it."},"bottom_flat_width":{"label":"Its bottom flat (6 o'clock), across","kind":"length","measurements":[{"id":"r-one","value":0.609,"unit":"in","source":{"type":"derived","expr":"{aero-r-one-15-handguard.bottom_flat_width}","via":"harvest"},"note":"Read on the R-ONE's view square on to its muzzle end (its ledger says how). The S-ONE is the same series with the middle of its rail taken off (Aero's Series row for both: \"R-ONE/S-ONE\"; Wing Tactical's table gives both the same four section figures, outside 1.95 by 1.51 and inside 1.65 by 1.3), no view square on to an S-ONE's end is on file, and its own views show the same faces: a flat at 6 o'clock with the detent's set screw in it at the receiver's end (5bea74f955a3) and a flat between two faces at the muzzle end (5a32198025ae)."}],"note":"Not this handguard's own reading: the R-ONE's figure by reference. A view square on to an S-ONE's end would replace it."},"lower_edge_width":{"label":"Width across the edges between its two lower faces (each side: the steep one under the side face, the shallow one into the bottom flat)","kind":"length","measurements":[{"id":"r-one","value":1.133,"unit":"in","source":{"type":"derived","expr":"{aero-r-one-15-handguard.lower_edge_width}","via":"harvest"},"note":"Read on the R-ONE's view square on to its muzzle end (its ledger says how). The S-ONE is the same series with the middle of its rail taken off (Aero's Series row for both: \"R-ONE/S-ONE\"; Wing Tactical's table gives both the same four section figures, outside 1.95 by 1.51 and inside 1.65 by 1.3), no view square on to an S-ONE's end is on file, and its own views show the same faces: two lower faces a side with a turn between them. Its far side's silhouette at the muzzle end in Wing Tactical's three-quarter view (5a32198025ae, rows 900 to 1003) is two straight stretches, 32 and 54 degrees from upright in the picture, with a turn of 22 degrees between them (rms 3.3 px for two lines, 6.3 for one, which misses by up to 35: .cache/batch8/aero-s-one-15-handguard/lower.py); and its side views have a row of thin slots in each, as the R-ONE's have."}],"note":"Not this handguard's own reading: the R-ONE's figure by reference. A view square on to an S-ONE's end would replace it."},"lower_edge_below_rail_top":{"label":"The edges between its two lower faces, below the rail's top","kind":"length","measurements":[{"id":"r-one","value":1.759,"unit":"in","source":{"type":"derived","expr":"{aero-r-one-15-handguard.lower_edge_below_rail_top}","via":"harvest"},"note":"Read on the R-ONE's view square on to its muzzle end (its ledger says how). The S-ONE is the same series with the middle of its rail taken off (Aero's Series row for both: \"R-ONE/S-ONE\"; Wing Tactical's table gives both the same four section figures, outside 1.95 by 1.51 and inside 1.65 by 1.3), no view square on to an S-ONE's end is on file, and its own views show the same faces: the turn between two lower faces (lower_edge_width's note)."}],"note":"Not this handguard's own reading: the R-ONE's figure by reference. A view square on to an S-ONE's end would replace it."},"rail_bridge_recess":{"label":"A bridge's top below the ears' (the lugs that have a middle)","kind":"length","measurements":[{"id":"r-one","value":0.03,"unit":"in","source":{"type":"derived","expr":"{aero-r-one-15-handguard.rail_bridge_recess}","via":"harvest"},"note":"Read on the R-ONE's view square on to its muzzle end (its ledger says how). The S-ONE is the same series with the middle of its rail taken off (Aero's Series row for both: \"R-ONE/S-ONE\"; Wing Tactical's table gives both the same four section figures, outside 1.95 by 1.51 and inside 1.65 by 1.3), no view square on to an S-ONE's end is on file, and its own views show the same faces: the bridged lugs' middles a step below their ears (5bea74f955a3)."}],"note":"Not this handguard's own reading: the R-ONE's figure by reference. A view square on to an S-ONE's end would replace it."},"rail_window_length":{"label":"A window along a rail block (the middle of an open lug, cut down between two bridged ones)","kind":"length","measurements":[{"id":"r-one","value":0.54,"unit":"in","source":{"type":"derived","expr":"{aero-r-one-15-handguard.rail_window_length}","via":"harvest"},"note":"Read on the R-ONE's view square on to its muzzle end (its ledger says how). The S-ONE is the same series with the middle of its rail taken off (Aero's Series row for both: \"R-ONE/S-ONE\"; Wing Tactical's table gives both the same four section figures, outside 1.95 by 1.51 and inside 1.65 by 1.3), no view square on to an S-ONE's end is on file, and its own views show the same faces: the second and fourth lug of each block open between their ears into a pocket with round ends that runs from one bridged lug to the next, deep and dark in both three-quarter views from above (fd3b9101db2b for the front block, 93c8ecc9fc0e for the rear)."}],"note":"Not this handguard's own reading: the R-ONE's figure by reference. A view square on to an S-ONE's end would replace it."},"rail_neck_foot_below_rail_top":{"label":"The neck's foot, where the two upper faces leave it, below the rail's top","kind":"length","measurements":[{"id":"sides","value":0.38,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-s-one-15-handguard 3c7e1b901211 and 44cb3b093489 (Sportsman's Warehouse's 1200 px copies of Aero's two gallery views of APRA500105A: its right side and its left)","scaleRef":"the view's own eight rail slots, four at each end, on one grid of the standard's pitch (std.picatinny.slot_pitch, .394) 36 pitches from the first to the last: a quadratic from pixels to inches through their centres, each within 0.002 in of it (74.7 px/in at the rear slot rising to 76.5 at the front in the right view, 75.5 falling to 74.8 in the left); down the picture at the scale of the middle of the rail","method":"the tone down the solid bars between its openings (4.85 and 8.02 ahead of the rail's first slot): under the spine's edge the neck's upright wall (55 to 79) gives way to the lit upper face (85 to 106) between 0.36 and 0.40 below the teeth's tops in all four columns (.cache/batch8/aero-s-one-15-handguard/levels.py)","via":"harvest"}},{"id":"r-one","value":0.377,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rail_neck_foot_below_rail_top}","via":"harvest"},"note":"The R-ONE's, read on the view square on to its muzzle end."}],"adopt":{"from":"sides","reason":"This handguard's own side views; the R-ONE's end view reads 0.003 from it."}},"rail_neck_width":{"label":"The neck its rail blocks stand on (under the rail's head, above the two upper faces), across","kind":"length","measurements":[{"id":"end","value":0.594,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-s-one-15-handguard 5bea74f955a3 (Wing Tactical's gallery: an S-ONE from its receiver end, looking forward along its top, its barrel nut in it; the page is for every length and doesn't say which this is)","scaleRef":"the rear rail block's head at the standard's .835 across its widest (std.picatinny.top_width), which shows on its first tooth's rear face: 295.5 px on rows 494 to 500, 353.9 px/in there; the front block's head, 13.0 in further off, is 148 px across, which puts the lens 13.0 in from that tooth; the rail's rear face, where the neck's two edges show, is 0.23 in nearer: 360 px/in","method":"the neck's two edges against the lit upper faces, rows 554 to 650: columns 541 and 755, 214 px. The arched opening under the head is 148 px between its upright sides on rows 608 to 650 (0.411 in: the neck less two walls of a tenth, within 0.02) (.cache/batch8/aero-s-one-15-handguard/endhead.py)","via":"harvest"}},{"id":"r-one","value":0.62,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rail_neck_width}","via":"harvest"},"note":"The R-ONE's, read on the view square on to its muzzle end."}],"adopt":{"from":"end","reason":"This handguard's own view from its receiver end, at its own rail head's scale; the R-ONE's reads 0.026 from it."}},"rail_centre_gap":{"label":"Its rail blocks' middle, between the two ears of a lug","kind":"length","measurements":[{"id":"end","value":0.4,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-s-one-15-handguard 5bea74f955a3 (Wing Tactical's gallery: an S-ONE from its receiver end, looking forward along its top, its barrel nut in it; the page is for every length and doesn't say which this is)","scaleRef":"the rear rail block's head at the standard's .835 across its widest (std.picatinny.top_width), which shows on its first tooth's rear face: 295.5 px on rows 494 to 500, 353.9 px/in there; the front block's head, 13.0 in further off, is 148 px across, which puts the lens 13.0 in from that tooth; the rear block's second lug is 0.49 in further off: 341 px/in","method":"the second lug's two ears' inner edges, rows 440 to 458: columns 577 and 713, 136 px (.cache/batch8/aero-s-one-15-handguard/endhead.py). The view shows every lug of the rear block cut down its middle between two ears, the first, third and fifth bridged a step below the ears' tops; a three-quarter view of the muzzle end (5a32198025ae) has the front block the same way, its lug at the muzzle end whole","via":"harvest"}},{"id":"r-one","value":0.365,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.rail_centre_gap}","via":"harvest"},"note":"The R-ONE's, read on the view square on to its muzzle end."}],"adopt":{"from":"end","reason":"This handguard's own view from its receiver end, at its own rail head's scale; the R-ONE's reads 0.035 less, inside what the two readings carry between them."}},"mlok_slot0_from_rail_slot0":{"label":"The rearmost M-LOK slot's centre on its sides, ahead of its rail's first slot","kind":"length","measurements":[{"id":"photo","value":4.073,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aero-s-one-15-handguard 3c7e1b901211 and 44cb3b093489 (Sportsman's Warehouse's 1200 px copies of Aero's two gallery views of APRA500105A: its right side and its left)","scaleRef":"the view's own eight rail slots, four at each end, on one grid of the standard's pitch (std.picatinny.slot_pitch, .394) 36 pitches from the first to the last: a quadratic from pixels to inches through their centres, each within 0.002 in of it (74.7 px/in at the rear slot rising to 76.5 at the front in the right view, 75.5 falling to 74.8 in the left)","method":"the seven long openings' centres along their row where the far side's shows through the near (see-through, so read at the rail's own scale), fitted to the M-LOK pitch (std.mlok.slot_pitch): their own pitch is 1.5738 in the right view and 1.5752 in the left for the standard's 1.5748, and the first's centre comes to 4.075 and 4.071 (.cache/batch8/aero-s-one-15-handguard/read.py)","via":"harvest"}}]},"mlok_slot0_x":{"label":"The rearmost M-LOK slot's centre on its sides, ahead of the receiver's face","kind":"length","measurements":[{"id":"derived","value":4.127,"unit":"in","source":{"type":"derived","expr":"{.rear_x} + {.rail_slot0_from_rear} + {.mlok_slot0_from_rail_slot0}","via":"harvest"}}]},"rail_slot0_x":{"label":"Its rear rail block's first slot (its centre) ahead of the receiver's face","kind":"length","measurements":[{"id":"derived","value":0.054,"unit":"in","source":{"type":"derived","expr":"{.rear_x} + {.rail_slot0_from_rear}","via":"harvest"},"note":"14.501 in behind the rail's front end, which the maker's length puts 15 in ahead of the receiver's shoulder: the rear end's own reading cancels."}]},"rail_front_slot0_x":{"label":"Its front rail block's first slot (its centre) ahead of the receiver's face","kind":"length","measurements":[{"id":"derived","value":13.056,"unit":"in","source":{"type":"derived","expr":"{.rail_slot0_x} + {.rail_front_slot0_from_slot0}","via":"harvest"}}]},"mlok_slots":{"label":"How many M-LOK slots on each side","kind":"count","measurements":[{"id":"photo","value":7,"unit":"count","source":{"type":"photo","photo":"references/aero-s-one-15-handguard 3c7e1b901211 and 44cb3b093489 (Sportsman's Warehouse's 1200 px copies of Aero's two gallery views of APRA500105A: its right side and its left)","scaleRef":"counted","method":"the long openings along the middle row of each side view: 7 in both, behind them one short slot and a round socket","via":"harvest"}}]},"mlok_row_below_rail_top":{"label":"The M-LOK row's middle on its sides, below the rail's top","kind":"length","measurements":[{"id":"photo","value":1.17,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-s-one-15-handguard 3c7e1b901211 and 44cb3b093489 (Sportsman's Warehouse's 1200 px copies of Aero's two gallery views of APRA500105A: its right side and its left)","scaleRef":"the view's own eight rail slots, four at each end, on one grid of the standard's pitch (std.picatinny.slot_pitch, .394) 36 pitches from the first to the last: a quadratic from pixels to inches through their centres, each within 0.002 in of it (74.7 px/in at the rear slot rising to 76.5 at the front in the right view, 75.5 falling to 74.8 in the left); down the picture at the scale of the middle of the rail","method":"the middle of the long openings' see-through height: 1.050 to 1.292 below the teeth's tops in the right view (1.171), 1.050 to 1.290 in the left (1.170). The socket's is 1.169 and 1.168","via":"harvest"}}],"note":"0.04 above the bore's level with the rail's top where the receiver's is (rail_top_above_bore), and within 0.03 of the middle of the side face it is in (0.885 to 1.51)."},"short_slot_centre_from_rail_slot0":{"label":"The short slot behind the M-LOK slots (in their row), its centre ahead of the rail's first slot","kind":"length","measurements":[{"id":"photo","value":2.888,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aero-s-one-15-handguard 3c7e1b901211 and 44cb3b093489 (Sportsman's Warehouse's 1200 px copies of Aero's two gallery views of APRA500105A: its right side and its left)","scaleRef":"the view's own eight rail slots, four at each end, on one grid of the standard's pitch (std.picatinny.slot_pitch, .394) 36 pitches from the first to the last: a quadratic from pixels to inches through their centres, each within 0.002 in of it (74.7 px/in at the rear slot rising to 76.5 at the front in the right view, 75.5 falling to 74.8 in the left)","method":"the short opening's see-through middle: 2.887 in the right view, 2.889 in the left","via":"harvest"}}]},"short_slot_length":{"label":"The short slot's length","kind":"length","measurements":[{"id":"photo","value":0.39,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-s-one-15-handguard 3c7e1b901211 and 44cb3b093489 (Sportsman's Warehouse's 1200 px copies of Aero's two gallery views of APRA500105A: its right side and its left)","scaleRef":"the view's own eight rail slots, four at each end, on one grid of the standard's pitch (std.picatinny.slot_pitch, .394) 36 pitches from the first to the last: a quadratic from pixels to inches through their centres, each within 0.002 in of it (74.7 px/in at the rear slot rising to 76.5 at the front in the right view, 75.5 falling to 74.8 in the left)","method":"its see-through length: 0.381 in the right view, 0.395 in the left (at least: the far side's end hides a little of the near's)","via":"harvest"}}]},"qd_socket_from_rail_slot0":{"label":"The QD sling socket on each side (3 and 9 o'clock), its centre ahead of the rail's first slot","kind":"length","measurements":[{"id":"photo","value":1.853,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aero-s-one-15-handguard 3c7e1b901211 and 44cb3b093489 (Sportsman's Warehouse's 1200 px copies of Aero's two gallery views of APRA500105A: its right side and its left)","scaleRef":"the view's own eight rail slots, four at each end, on one grid of the standard's pitch (std.picatinny.slot_pitch, .394) 36 pitches from the first to the last: a quadratic from pixels to inches through their centres, each within 0.002 in of it (74.7 px/in at the rear slot rising to 76.5 at the front in the right view, 75.5 falling to 74.8 in the left)","method":"the round opening's see-through middle: 1.853 in both views","via":"harvest"}}],"note":"Aero: \"Quick disconnect sling socket at the 3, 6 and 9 o'clock positions\"."},"qd_socket_d":{"label":"The QD sling socket's diameter, as it shows","kind":"length","measurements":[{"id":"photo","value":0.35,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-s-one-15-handguard 3c7e1b901211 and 44cb3b093489 (Sportsman's Warehouse's 1200 px copies of Aero's two gallery views of APRA500105A: its right side and its left)","scaleRef":"the view's own eight rail slots, four at each end, on one grid of the standard's pitch (std.picatinny.slot_pitch, .394) 36 pitches from the first to the last: a quadratic from pixels to inches through their centres, each within 0.002 in of it (74.7 px/in at the rear slot rising to 76.5 at the front in the right view, 75.5 falling to 74.8 in the left); down the picture at the scale of the middle of the rail","method":"its see-through height, 0.32 in both views, and what the far rim hides of it from a lens a little above the rail's level: the M-LOK slots beside it show 0.242 of the standard's 0.276 the same way (0.034)","via":"harvest"}}],"note":"The opening as it shows, not the socket's standard size, which no page gives."},"thin_slot_first_from_rail_slot0":{"label":"The thin slots' first centre ahead of the rail's first slot (all four rows)","kind":"length","measurements":[{"id":"photo","value":2.168,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/aero-s-one-15-handguard 3c7e1b901211 and 44cb3b093489 (Sportsman's Warehouse's 1200 px copies of Aero's two gallery views of APRA500105A: its right side and its left)","scaleRef":"the view's own eight rail slots, four at each end, on one grid of the standard's pitch (std.picatinny.slot_pitch, .394) 36 pitches from the first to the last: a quadratic from pixels to inches through their centres, each within 0.002 in of it (74.7 px/in at the rear slot rising to 76.5 at the front in the right view, 75.5 falling to 74.8 in the left)","method":"the first see-through opening of each row: 2.171, 2.172, 2.169 and 2.173 in the right view's four rows, 2.175, 2.163 and 2.162 in the left's three that show","via":"harvest"}}]},"thin_slot_pitch":{"label":"The thin slots' pitch along each row","kind":"length","measurements":[{"id":"photo","value":1.0664,"unit":"in","pm":0.002,"source":{"type":"photo","photo":"references/aero-s-one-15-handguard 3c7e1b901211 and 44cb3b093489 (Sportsman's Warehouse's 1200 px copies of Aero's two gallery views of APRA500105A: its right side and its left)","scaleRef":"the view's own eight rail slots, four at each end, on one grid of the standard's pitch (std.picatinny.slot_pitch, .394) 36 pitches from the first to the last: a quadratic from pixels to inches through their centres, each within 0.002 in of it (74.7 px/in at the rear slot rising to 76.5 at the front in the right view, 75.5 falling to 74.8 in the left)","method":"a row's twelve see-through openings, first to last over eleven pitches: 1.0659 in the right view's lower inner row, 1.0667 and 1.0669 in the left's two inner rows","via":"harvest"}}]},"thin_slot_count":{"label":"Thin slots in each row","kind":"count","measurements":[{"id":"photo","value":12,"unit":"count","source":{"type":"photo","photo":"references/aero-s-one-15-handguard 3c7e1b901211 and 44cb3b093489 (Sportsman's Warehouse's 1200 px copies of Aero's two gallery views of APRA500105A: its right side and its left)","scaleRef":"counted","method":"the see-through openings along each inner row, in both views: 12 (the outer rows show 11 or 12 of them: the far side hides more of those)","via":"harvest"}}]},"thin_slot_length":{"label":"A thin slot's length (at least: what shows through both walls)","kind":"length","measurements":[{"id":"photo","value":0.93,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-s-one-15-handguard 3c7e1b901211 and 44cb3b093489 (Sportsman's Warehouse's 1200 px copies of Aero's two gallery views of APRA500105A: its right side and its left)","scaleRef":"the view's own eight rail slots, four at each end, on one grid of the standard's pitch (std.picatinny.slot_pitch, .394) 36 pitches from the first to the last: a quadratic from pixels to inches through their centres, each within 0.002 in of it (74.7 px/in at the rear slot rising to 76.5 at the front in the right view, 75.5 falling to 74.8 in the left)","method":"the longest see-through openings, those nearest the lens's axis: 0.930 in the right view, 0.930 in the left; they shorten to 0.83 toward each end as the far side's ends hide the near's","via":"harvest"}}]},"thin_slot_width":{"label":"A thin slot's width, across the slanted face it is in","kind":"length","measurements":[{"id":"r-one","value":0.22,"unit":"in","source":{"type":"derived","expr":"{aero-r-one-15-handguard.thin_slot_width}","via":"harvest"},"note":"The R-ONE's openings as its side views have their rims. This handguard's see-through windows are as tall as the R-ONE's row for row (0.04 for the upper outer row, 0.09 the upper inner, 0.10 the lower inner, 0.03 the lower outer), which is what an opening of that width leaves through both walls."}],"note":"Not this handguard's own reading of the rims: the R-ONE's figure by reference."},"thin_slot_row_a_y":{"label":"The upper outer row of thin slots, its height above the bore","kind":"length","measurements":[{"id":"photo","value":0.648,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-s-one-15-handguard 3c7e1b901211 and 44cb3b093489 (Sportsman's Warehouse's 1200 px copies of Aero's two gallery views of APRA500105A: its right side and its left)","scaleRef":"the view's own eight rail slots, four at each end, on one grid of the standard's pitch (std.picatinny.slot_pitch, .394) 36 pitches from the first to the last: a quadratic from pixels to inches through their centres, each within 0.002 in of it (74.7 px/in at the rear slot rising to 76.5 at the front in the right view, 75.5 falling to 74.8 in the left); down the picture at the scale of the middle of the rail","method":"the middle of the row's see-through window, 0.564 below the teeth's tops in both views, from the rail's top at rail_top_above_bore","via":"harvest"}},{"id":"r-one-opening","value":0.71,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.thin_slot_row_a_y}","via":"harvest"},"note":"The R-ONE's row, where its side views have the opening's own rim."}],"adopt":{"from":"r-one-opening","reason":"The opening's rim as the R-ONE's side views have it: this handguard's see-through windows match the R-ONE's within 0.012 in, so its openings are taken to stand where the R-ONE's do, each down the middle of its own face."},"note":"What shows through both walls isn't the opening: the faces slant, and the far side's rim hides part of the near's. The R-ONE's rows were read both ways; this handguard's see-through windows stand within 0.012 in of the R-ONE's, row for row (0.565, 0.773, 1.587 and 1.805 below the rail's top here; 0.553, 0.770, 1.598 and 1.813 there)."},"thin_slot_row_b_y":{"label":"The upper inner row of thin slots, its height above the bore","kind":"length","measurements":[{"id":"photo","value":0.44,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-s-one-15-handguard 3c7e1b901211 and 44cb3b093489 (Sportsman's Warehouse's 1200 px copies of Aero's two gallery views of APRA500105A: its right side and its left)","scaleRef":"the view's own eight rail slots, four at each end, on one grid of the standard's pitch (std.picatinny.slot_pitch, .394) 36 pitches from the first to the last: a quadratic from pixels to inches through their centres, each within 0.002 in of it (74.7 px/in at the rear slot rising to 76.5 at the front in the right view, 75.5 falling to 74.8 in the left); down the picture at the scale of the middle of the rail","method":"the middle of the row's see-through window, 0.772 below the teeth's tops in both views, from the rail's top at rail_top_above_bore","via":"harvest"}},{"id":"r-one-opening","value":0.46,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.thin_slot_row_b_y}","via":"harvest"},"note":"The R-ONE's row, where its side views have the opening's own rim."}],"adopt":{"from":"r-one-opening","reason":"The opening's rim as the R-ONE's side views have it: this handguard's see-through windows match the R-ONE's within 0.012 in, so its openings are taken to stand where the R-ONE's do, each down the middle of its own face."},"note":"What shows through both walls isn't the opening: the faces slant, and the far side's rim hides part of the near's. The R-ONE's rows were read both ways; this handguard's see-through windows stand within 0.012 in of the R-ONE's, row for row (0.565, 0.773, 1.587 and 1.805 below the rail's top here; 0.553, 0.770, 1.598 and 1.813 there)."},"thin_slot_row_d_y":{"label":"The lower inner row of thin slots, its height above the bore","kind":"length","measurements":[{"id":"photo","value":-0.374,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-s-one-15-handguard 3c7e1b901211 and 44cb3b093489 (Sportsman's Warehouse's 1200 px copies of Aero's two gallery views of APRA500105A: its right side and its left)","scaleRef":"the view's own eight rail slots, four at each end, on one grid of the standard's pitch (std.picatinny.slot_pitch, .394) 36 pitches from the first to the last: a quadratic from pixels to inches through their centres, each within 0.002 in of it (74.7 px/in at the rear slot rising to 76.5 at the front in the right view, 75.5 falling to 74.8 in the left); down the picture at the scale of the middle of the rail","method":"the middle of the row's see-through window, 1.587 below the teeth's tops in both views, from the rail's top at rail_top_above_bore","via":"harvest"}},{"id":"r-one-opening","value":-0.41,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.thin_slot_row_d_y}","via":"harvest"},"note":"The R-ONE's row, where its side views have the opening's own rim."}],"adopt":{"from":"r-one-opening","reason":"The opening's rim as the R-ONE's side views have it: this handguard's see-through windows match the R-ONE's within 0.012 in, so its openings are taken to stand where the R-ONE's do, each down the middle of its own face."},"note":"What shows through both walls isn't the opening: the faces slant, and the far side's rim hides part of the near's. The R-ONE's rows were read both ways; this handguard's see-through windows stand within 0.012 in of the R-ONE's, row for row (0.565, 0.773, 1.587 and 1.805 below the rail's top here; 0.553, 0.770, 1.598 and 1.813 there)."},"thin_slot_row_e_y":{"label":"The lower outer row of thin slots, its height above the bore","kind":"length","measurements":[{"id":"photo","value":-0.592,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-s-one-15-handguard 3c7e1b901211 and 44cb3b093489 (Sportsman's Warehouse's 1200 px copies of Aero's two gallery views of APRA500105A: its right side and its left)","scaleRef":"the view's own eight rail slots, four at each end, on one grid of the standard's pitch (std.picatinny.slot_pitch, .394) 36 pitches from the first to the last: a quadratic from pixels to inches through their centres, each within 0.002 in of it (74.7 px/in at the rear slot rising to 76.5 at the front in the right view, 75.5 falling to 74.8 in the left); down the picture at the scale of the middle of the rail","method":"the middle of the row's see-through window, 1.804 below the teeth's tops in both views, from the rail's top at rail_top_above_bore","via":"harvest"}},{"id":"r-one-opening","value":-0.635,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{aero-r-one-15-handguard.thin_slot_row_e_y}","via":"harvest"},"note":"The R-ONE's row, where its side views have the opening's own rim."}],"adopt":{"from":"r-one-opening","reason":"The opening's rim as the R-ONE's side views have it: this handguard's see-through windows match the R-ONE's within 0.012 in, so its openings are taken to stand where the R-ONE's do, each down the middle of its own face."},"note":"What shows through both walls isn't the opening: the faces slant, and the far side's rim hides part of the near's. The R-ONE's rows were read both ways; this handguard's see-through windows stand within 0.012 in of the R-ONE's, row for row (0.565, 0.773, 1.587 and 1.805 below the rail's top here; 0.553, 0.770, 1.598 and 1.813 there)."},"reach_inside":{"label":"The room inside its side faces, from the face in to the barrel (what an M-LOK accessory's nuts may take)","kind":"length","measurements":[],"note":"It depends on the barrel under it, another part: no figure."}}},{"subject":"aimpoint-duty-rds-30mm-mount","title":"Aimpoint's one-piece torsion nut mount, 30 mm: the lower mount the Duty RDS is sold on (200758), and sold alone (200768)","dimensions":{"deck_above_rail":{"label":"The deck's top (the seam under the sight's foot, where a dot's base sits) above the rail's top","kind":"length","measurements":[{"id":"table-less-duty-rds","value":0.152,"unit":"in","pm":0.017,"source":{"type":"derived","expr":"{.axis_above_rail} - {aimpoint-duty-rds.axis_above_base}","via":"harvest"},"note":"30 mm (1.181 in) less the Duty RDS's 1.029 in."},{"id":"profile-left","value":0.127,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aimpoint-duty-rds a1c7d3917b7a (Aimpoint's 200758, the Duty RDS on its 30 mm mount, straight left side, as The Shooting Centre shows it (ISS7058-002), 1280 px)","scaleRef":"the sight's own length, its cover rings' span along their middle rows: 1170 px here and 976 px in Aimpoint's left view of the 39 mm pair, whose scale the sight's ledger has (315.0 px/in): 377.6 px/in","method":"the seam under the sight's foot (rows 1075 to 1080) is 8 to 13 px over the locking bar's top (row 1088) here; the 39 mm pair's is 0.404 in over its bar's top (aimpoint-duty-rds.underside_above_clamp_bottom less jaw_top_above_clamp_bottom): 0.379 in less, on the 39 mm mount's deck (0.5064)","via":"harvest"}}],"adopt":{"from":"table-less-duty-rds","reason":"Aimpoint's own axis height less the sight's own axis over its base, as every red dot mount's deck is drawn (D101, D102); the reading through the locking bar, 0.025 in lower and inside the two figures' ±, stays beside it."},"note":"Aimpoint gives the mount's height only as the Duty RDS's axis on it: \"Height of Optical Axis 30 mm (1.2 in) measured from top surface of mounting platform\". Less the Duty RDS's own axis over its base it is the deck's height: 0.354 in, 9 mm, under the 39 mm mount's, which is the two axis heights' difference. Read on the 30 mm pair's own left view through the locking bar (the same bar on both mounts), its seam stands 0.38 in under the 39 mm's, and so 0.025 in lower: kept beside it."},"axis_above_rail":{"label":"The Duty RDS's axis above the rail's top on this mount (Aimpoint's figure for the pair)","kind":"length","measurements":[{"id":"tsc","value":30,"unit":"mm","stated":"Height of Optical Axis 30 mm (1.2 in) measured from top surface of mounting platform","source":{"type":"spec","publisher":"retailer","name":"The Shooting Centre, Aimpoint Duty RDS 2 MOA with 30 mm One-piece TNP Mount (MPN 200758), Aimpoint's table","url":"https://store.theshootingcentre.com/aimpoint-duty-rds-2-moa-red-dot-reflex-sight-with-30-mm-one-piece-tnp-mount/","retrieved":"2026-11-05","via":"harvest"}},{"id":"sight-ledger","value":1.1811,"unit":"in","source":{"type":"derived","expr":"{aimpoint-duty-rds.standard_axis_above_rail}","via":"harvest"},"note":"The sight's ledger's figure for the standard mount, from Aimpoint's 2025 manual and T.REX ARMS' table."}],"adopt":{"from":"tsc","reason":"Aimpoint's table for the pair on this mount, as a seller prints it; the manual's standard mount, in the sight's ledger, is the same 30 mm."}},"deck_x":{"label":"The footprint's middle along the deck, ahead of the clamp's middle","kind":"length","measurements":[{"id":"assumed","value":0,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{aimpoint-duty-rds-39mm-mount.deck_x}","via":"harvest"},"note":"As on the 39 mm mount: no view shows the footprint's screws or lug, and their middle is taken to be the mount's."}]},"mount_length":{"label":"The mount's length along the rail","kind":"length","measurements":[{"id":"profile-left","value":2.045,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aimpoint-duty-rds.mount_length}","via":"harvest"},"note":"The 39 mm pair's reading: the 30 mm pair's left view has the same block as long, 773 px at 377.6 px/in (2.047 in)."}]},"clamp_below_rail":{"label":"How far the mount reaches below the rail's top","kind":"length","measurements":[{"id":"profile-left","value":0.4,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{aimpoint-duty-rds.clamp_below_rail}","via":"harvest"},"note":"The same block as the 39 mm mount under its locking bar's top."}]},"weight":{"label":"Weight (the mount, its locking bar and its screw)","kind":"mass","measurements":[{"id":"table","value":32,"unit":"g","pm":1,"source":{"type":"derived","basis":"The Shooting Centre's copy of Aimpoint's table for 200758: \"Weight 140 g\" less \"Weight - Sight Only 108 g\" (both on the page, read 2026-11-05)."}}],"note":"What Aimpoint's two weights for the pair leave between them, as for the 39 mm mount: the pair (\"Weight 140 g (4.9 oz)\") less the sight alone (\"Weight - Sight Only 108 g (3.8 oz)\"). The 39 mm mount's 52 g is 20 g more."}}},{"subject":"aimpoint-duty-rds-39mm-mount","title":"Aimpoint's one-piece torsion nut mount and spacer, 39 mm, the mount the Duty RDS is sold on (200759)","dimensions":{"deck_above_rail":{"label":"The deck's top (the seam under the sight's foot, where a dot's base sits) above the rail's top","kind":"length","measurements":[{"id":"sheet-less-duty-rds","value":0.5064,"unit":"in","pm":0.017,"source":{"type":"derived","expr":"{aimpoint-duty-rds.optical_axis_above_rail} - {aimpoint-duty-rds.axis_above_base}","via":"harvest"},"note":"39 mm (1.535 in) less the Duty RDS's 1.029 in."}],"note":"Aimpoint gives the mount's height only as the Duty RDS's axis on it: \"Keyed Surface Mount: One-Piece Torsion Nut 39 mm Mount\", its axis 39 mm over the rail (the sheet). Less the Duty RDS's own axis over its base it is the deck's height; another Micro-footprint dot on it stands as much higher or lower as its own axis is over its base (D101): a Micro T-2 on it, 0.44 in lower."},"deck_x":{"label":"The footprint's middle along the deck, ahead of the clamp's middle","kind":"length","measurements":[{"id":"assumed","value":0,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view shows the footprint's screws or lug. Their middle is taken to be the mount's, which is where the frame's origin is along the rail (the side outline's origin is the mount's middle over its rows, under the sight's foot, which is within a few hundredths as long: aimpoint-duty-rds's profiles.side and mount_length)."}}]},"mount_length":{"label":"The mount's length along the rail","kind":"length","measurements":[{"id":"profile-left","value":2.045,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{aimpoint-duty-rds.mount_length}","via":"harvest"},"note":"Read on Aimpoint's left profile of the pair, in the sight's ledger."}]},"clamp_below_rail":{"label":"How far the mount reaches below the rail's top","kind":"length","measurements":[{"id":"profile-left","value":0.4,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{aimpoint-duty-rds.clamp_below_rail}","via":"harvest"},"note":"Where the sheet's 39 mm puts the rail's top under the axis of the pair: the sight's ledger says how."}]},"weight":{"label":"Weight (the mount, its locking bar and its screw)","kind":"mass","measurements":[{"id":"sheet-less-sight","value":52,"unit":"g","pm":1,"source":{"type":"derived","expr":"{aimpoint-duty-rds.weight} - {aimpoint-duty-rds.sight_weight}","via":"harvest"},"note":"160 g less 108 g."},{"id":"ot","value":57,"unit":"g","source":{"type":"derived","basis":"Optics Trade's two figures for its own listing: \"Approximately 108 g (3.8 oz) without mount; 165 g (5.8 oz) with integrated mount for a lightweight setup.\" (aimpoint-duty-rds.weight, its measurement ot): 165 g less 108 g."}}],"adopt":{"from":"sheet-less-sight","reason":"The maker's own two figures; a seller's two leave 5 g more, kept beside it."},"note":"What the maker's two weights leave between them: the pair \"lens covers, mount, & battery\" (the sheet's 160 g) less the sight alone (its 108 g, which doesn't say whether the battery or the covers are in it). Optics Trade's two figures for its listing leave 57 g. So a build's weight doesn't move with the split (D101)."}}},{"subject":"aimpoint-duty-rds","title":"Aimpoint Duty RDS Red Dot Sight - One-piece Torsion Nut Mount, 39mm (200759): the sight on its 39 mm mount","dimensions":{"length":{"label":"Overall length (the configuration: with its lens covers, closed)","kind":"length","measurements":[{"id":"sheet","value":80,"unit":"mm","stated":"Size L x W x H (mm) Conf: 80 x 37 x 67 mm","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Duty RDS spec sheet for item 200759 (Ed. 7-May-21), the PDF as T.REX ARMS hosts it","url":"https://img.trex-arms.com/wp/uploads/2026/03/aimpoint-duty-rds-specs-2021-05-07.pdf","retrieved":"2026-10-19","via":"harvest"}},{"id":"midway","value":3.1,"unit":"in","pm":0.05,"stated":"Length 3.1 Inches","source":{"type":"spec","publisher":"retailer","name":"MidwayUSA, Aimpoint Duty RDS Red Dot Reflex Red Dot Sight 2 MOA Dot 39mm (a product family with a reticle choice)","url":"https://www.midwayusa.com/product/1024757827","retrieved":"2026-10-19","via":"harvest"},"note":"The sheet's inch figure for the configuration (\"3.1 x 1.5 x 2.6 in\")."}],"adopt":{"from":"sheet","reason":"The sheet printed for this item; the seller repeats its inch figure."},"note":"The sheet's \"Conf\" length: the sight with its lens covers and mount. The mount doesn't reach past the covers in the side views, so it is the covers' length. With the covers raised, as every studio view has them and as the model is drawn, the sight is ring_span long."},"sight_length":{"label":"The sight's own length, without its lens covers and mount","kind":"length","measurements":[{"id":"sheet","value":68,"unit":"mm","stated":"Size L x W x H (mm) Sight Only: 68 x 37 x 43 mm","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Duty RDS spec sheet for item 200759 (Ed. 7-May-21), the PDF as T.REX ARMS hosts it","url":"https://img.trex-arms.com/wp/uploads/2026/03/aimpoint-duty-rds-specs-2021-05-07.pdf","retrieved":"2026-10-19","via":"harvest"}},{"id":"manual","value":68,"unit":"mm","stated":"Sight only 68 mm × 37 mm × 43 mm","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Duty RDS user manual ([16661-4], 2021, 2025), the PDF as T.REX ARMS hosts it","url":"https://img.trex-arms.com/wp/uploads/2026/03/aimpoint-duty-rds-user-manual-2025.pdf","retrieved":"2026-10-19","via":"harvest"}},{"id":"bcm","value":68,"unit":"mm","stated":"Length x Width x Height 2.7 x 1.5 x 1.7 in / 68 x 37 x 43 mm","source":{"type":"spec","publisher":"retailer","name":"Bravo Company USA, Aimpoint Duty RDS Red Dot Sight - One-piece Torsion Nut Mount, 39mm (AIMPOINT-200759)","url":"https://bravocompanyusa.com/aimpoint-duty-rds-red-dot-sight-one-piece-torsion-nut-mount-39mm/","retrieved":"2026-10-19","via":"harvest"}}],"adopt":{"from":"sheet","reason":"The sheet printed for this item; the manual and the seller give the same."},"note":"\"Sight Only\": the bare sight, without the rubber lens covers whose rings wrap its two ends. Not seen in any photo on file: every one has the covers on."},"width":{"label":"Overall width (the sight's own, the same with its mount)","kind":"length","measurements":[{"id":"sheet","value":37,"unit":"mm","stated":"Size L x W x H (mm) Conf: 80 x 37 x 67 mm","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Duty RDS spec sheet for item 200759 (Ed. 7-May-21), the PDF as T.REX ARMS hosts it","url":"https://img.trex-arms.com/wp/uploads/2026/03/aimpoint-duty-rds-specs-2021-05-07.pdf","retrieved":"2026-10-19","via":"harvest"}},{"id":"manual","value":37,"unit":"mm","stated":"Sight only 68 mm × 37 mm × 43 mm","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Duty RDS user manual ([16661-4], 2021, 2025), the PDF as T.REX ARMS hosts it","url":"https://img.trex-arms.com/wp/uploads/2026/03/aimpoint-duty-rds-user-manual-2025.pdf","retrieved":"2026-10-19","via":"harvest"}},{"id":"bcm","value":37,"unit":"mm","stated":"Length x Width x Height 2.7 x 1.5 x 1.7 in / 68 x 37 x 43 mm","source":{"type":"spec","publisher":"retailer","name":"Bravo Company USA, Aimpoint Duty RDS Red Dot Sight - One-piece Torsion Nut Mount, 39mm (AIMPOINT-200759)","url":"https://bravocompanyusa.com/aimpoint-duty-rds-red-dot-sight-one-piece-torsion-nut-mount-39mm/","retrieved":"2026-10-19","via":"harvest"}}],"adopt":{"from":"sheet","reason":"The sheet printed for this item; the manual and the seller give the same."},"note":"The same 37 mm for the sight alone and for the configuration, so the mount is no wider than the sight. Neither document says what it spans: taken here from the face of the keypad on the left to the face of the battery cap on the right, the furthest things out on the two sides in the quarter views."},"height":{"label":"Overall height (the configuration: the mount's bottom to the housing's top, lids and hinges left out)","kind":"length","measurements":[{"id":"sheet","value":67,"unit":"mm","stated":"Size L x W x H (mm) Conf: 80 x 37 x 67 mm","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Duty RDS spec sheet for item 200759 (Ed. 7-May-21), the PDF as T.REX ARMS hosts it","url":"https://img.trex-arms.com/wp/uploads/2026/03/aimpoint-duty-rds-specs-2021-05-07.pdf","retrieved":"2026-10-19","via":"harvest"}},{"id":"midway","value":2.6,"unit":"in","pm":0.05,"stated":"Height 2.6 Inches","source":{"type":"spec","publisher":"retailer","name":"MidwayUSA, Aimpoint Duty RDS Red Dot Reflex Red Dot Sight 2 MOA Dot 39mm (a product family with a reticle choice)","url":"https://www.midwayusa.com/product/1024757827","retrieved":"2026-10-19","via":"harvest"},"note":"The sheet's inch figure for the configuration."}],"adopt":{"from":"sheet","reason":"The sheet printed for this item; the seller repeats its inch figure."},"note":"The sheet's \"Conf\" height. What it spans isn't said: it is taken from the mount's bottom to the top of the housing's rear hump, the raised lids and the hinges' lugs left out, as Aimpoint's sheet for the Micro T-2 measures its configuration (there that height landed on a rail's pitch within 0.5%: aimpoint-micro-t-2.standard_conf_height). It is the scale of Aimpoint's left profile (profiles.side). Two checks of it, neither a published figure of this part's alone: the sheet's 43 mm of sight reads 44.0 mm on that profile from the seam under the sight's foot to the housing's top (sight_height); and T.REX's photo of this sight beside a Micro T-2 on one rail puts its length over the cover rings 1.073 times the T-2's (ring_span). The lugs of the covers' hinges stand 0.1 in higher than the housing: measured to them, the height would be 2.4% more."},"sight_height":{"label":"The sight's own height (its underside to the housing's top)","kind":"length","measurements":[{"id":"sheet","value":43,"unit":"mm","stated":"Size L x W x H (mm) Sight Only: 68 x 37 x 43 mm","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Duty RDS spec sheet for item 200759 (Ed. 7-May-21), the PDF as T.REX ARMS hosts it","url":"https://img.trex-arms.com/wp/uploads/2026/03/aimpoint-duty-rds-specs-2021-05-07.pdf","retrieved":"2026-10-19","via":"harvest"}},{"id":"manual","value":43,"unit":"mm","stated":"Sight only 68 mm × 37 mm × 43 mm","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Duty RDS user manual ([16661-4], 2021, 2025), the PDF as T.REX ARMS hosts it","url":"https://img.trex-arms.com/wp/uploads/2026/03/aimpoint-duty-rds-user-manual-2025.pdf","retrieved":"2026-10-19","via":"harvest"}},{"id":"profile-left","value":1.733,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.height} - {.underside_above_clamp_bottom}","via":"harvest"},"note":"On the photo: the housing's top 2.638 in above the mount's bottom (the scale), and the seam under the sight's foot 0.906 in above it."}],"adopt":{"from":"sheet","reason":"The sheet printed for this item; the manual gives the same. The photo's reading is 1 mm more and is kept beside it."},"note":"\"Sight Only\": the sight without its mount. On Aimpoint's left profile at the scale of the configuration's 67 mm, the seam under the sight's foot (a dark line across the whole foot, rows 936 to 940) is 1.733 in under the housing's top: 44.0 mm, 1 mm more than the maker's figure. Either the 67 mm is measured to something a little higher than the housing (the hinges' lugs stand 0.1 in higher), or the sight's underside is a little above the line that shows. Both are kept; the model draws the seam where it shows."},"optical_axis_above_rail":{"label":"Optical axis above the rail's top (on the 39 mm mount)","kind":"length","measurements":[{"id":"sheet","value":39,"unit":"mm","stated":"Height of Optical Axis: Sight and mount – 39 mm (1.2 in) measured from top surface of Picatinny/Weaver rail","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Duty RDS spec sheet for item 200759 (Ed. 7-May-21), the PDF as T.REX ARMS hosts it","url":"https://img.trex-arms.com/wp/uploads/2026/03/aimpoint-duty-rds-specs-2021-05-07.pdf","retrieved":"2026-10-19","via":"harvest"}},{"id":"manual","value":39,"unit":"mm","stated":"High mount 39 mm / 1.5 in","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Duty RDS user manual ([16661-4], 2021, 2025), the PDF as T.REX ARMS hosts it","url":"https://img.trex-arms.com/wp/uploads/2026/03/aimpoint-duty-rds-user-manual-2025.pdf","retrieved":"2026-10-19","via":"harvest"}},{"id":"trex-guide","value":1.54,"unit":"in","stated":"Standard Duty RDS Mount N/A 1.54\" Centerline","source":{"type":"spec","publisher":"review","name":"T.REX ARMS, Aimpoint Duty RDS Mount Height Comparison Guide (Cody Rediker, 2022-02-02): T.REX's own figures for centreline heights","url":"https://www.trex-arms.com/buyers-guides/aimpoint-duty-rds-mount-height-comparison-guide-210","retrieved":"2026-10-19","via":"harvest"},"note":"T.REX's table: the maker's 39 mm in inches."}],"adopt":{"from":"sheet","reason":"The sheet printed for this item; the manual's line for the 39 mm mount and T.REX's inch figure say the same."},"note":"The sheet's height for the sight on its mount, and what the mount is named for. Its inch figure is wrong: 39 mm is 1.54 in (the \"1.2 in\" is the 30 mm mount's, as the manual's two lines show: \"Standard mount 30 mm / 1.2 in\", \"High mount 39 mm / 1.5 in\"). T.REX ARMS says it in inches: \"The Duty RDS ships with a 39mm (1.54\\\") mount, which puts it above absolute co-witness height, but slightly lower than most lower 1/3rd mounts.\" Where the rail's top lies inside the mount isn't seen in a side view: the model's rail top is this far under the axis."},"standard_axis_above_rail":{"label":"Optical axis above the rail on the 30 mm mount (not this part's)","kind":"length","measurements":[{"id":"manual","value":30,"unit":"mm","stated":"Standard mount 30 mm / 1.2 in","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Duty RDS user manual ([16661-4], 2021, 2025), the PDF as T.REX ARMS hosts it","url":"https://img.trex-arms.com/wp/uploads/2026/03/aimpoint-duty-rds-user-manual-2025.pdf","retrieved":"2026-10-19","via":"harvest"}}],"note":"The manual's other mount base (9A), sold as another configuration: kept so the two aren't confused."},"axis_above_base":{"label":"Optical axis above the sight's own base (the seam under its foot, where its footprint meets a mount's deck: D101)","kind":"length","measurements":[{"id":"profile-left","value":1.029,"unit":"in","pm":0.017,"source":{"type":"derived","expr":"{.axis_above_clamp_bottom} - {.underside_above_clamp_bottom}","via":"harvest"},"note":"1.935 in less 0.906 in, the two readings' ± together."}],"note":"What the sight brings to any Micro-footprint mount (D101): its axis this far over the deck it is screwed to, read on Aimpoint's left profile of 200759 between the axis and the seam under the sight's foot. On its own 39 mm mount it puts the axis at the sheet's 39 mm, which is what the mount's deck height is worked out from (aimpoint-duty-rds-39mm-mount.deck_above_rail). Two of T.REX ARMS' sentences are its check, neither of them read to make it: \"the optic sits roughly .40–.50 inches taller than a T-1/T-2 would sit on the same mount\" (this less aimpoint-micro-t-2.axis_above_base is 0.44 in), and \"At 1.89\", standard iron sights will not co-witness with the Duty RDS on absolute height aftermarket mounts\" (on a deck that puts a T-2 at 1.41 in it is at 1.85 in, 0.04 in under T.REX's figure and inside the two readings' ±)."},"window_d":{"label":"Clear aperture","kind":"length","measurements":[{"id":"sheet","value":18,"unit":"mm","stated":"Clear Aperture: 18 mm (.71 in)","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Duty RDS spec sheet for item 200759 (Ed. 7-May-21), the PDF as T.REX ARMS hosts it","url":"https://img.trex-arms.com/wp/uploads/2026/03/aimpoint-duty-rds-specs-2021-05-07.pdf","retrieved":"2026-10-19","via":"harvest"}},{"id":"manual","value":18,"unit":"mm","stated":"Clear aperture 18 mm","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Duty RDS user manual ([16661-4], 2021, 2025), the PDF as T.REX ARMS hosts it","url":"https://img.trex-arms.com/wp/uploads/2026/03/aimpoint-duty-rds-user-manual-2025.pdf","retrieved":"2026-10-19","via":"harvest"}}],"adopt":{"from":"sheet","reason":"The sheet printed for this item; the manual gives the same."},"note":"Draws the lens at both ends; the real ones are set back inside the tube (the sheet: \"PROTECTED RECESSED LENS\")."},"weight":{"label":"Weight (the configuration: the sight with its lens covers, its mount and its battery)","kind":"mass","measurements":[{"id":"sheet","value":160,"unit":"g","stated":"Weight (Conf): 160 g / 5.6 oz (lens covers, mount, & battery)","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Duty RDS spec sheet for item 200759 (Ed. 7-May-21), the PDF as T.REX ARMS hosts it","url":"https://img.trex-arms.com/wp/uploads/2026/03/aimpoint-duty-rds-specs-2021-05-07.pdf","retrieved":"2026-10-19","via":"harvest"}},{"id":"ot","value":165,"unit":"g","stated":"Weight: Approximately 108 g (3.8 oz) without mount; 165 g (5.8 oz) with integrated mount for a lightweight setup.","source":{"type":"spec","publisher":"retailer","name":"Optics Trade, Aimpoint Duty RDS (a configurable listing, 30 mm or 39 mm mount)","url":"https://www.optics-trade.eu/en/aimpoint-duty-rds.html","retrieved":"2026-10-19","via":"harvest"}},{"id":"midway","value":5.7,"unit":"oz","pm":0.05,"stated":"Weight 5.7 Ounce","source":{"type":"spec","publisher":"retailer","name":"MidwayUSA, Aimpoint Duty RDS Red Dot Reflex Red Dot Sight 2 MOA Dot 39mm (a product family with a reticle choice)","url":"https://www.midwayusa.com/product/1024757827","retrieved":"2026-10-19","via":"harvest"}}],"adopt":{"from":"sheet","reason":"The maker's sheet for this item, and it says what it includes; the sellers' figures are kept beside it."},"note":"The sheet says what is in it: \"lens covers, mount, & battery\". A European seller's 165 g is for its own listing (\"with integrated mount\", which mount isn't said); MidwayUSA's 5.7 oz is for a family that offers the multi-reticle sight too."},"sight_weight":{"label":"Weight of the sight alone (without its mount and covers)","kind":"mass","measurements":[{"id":"sheet","value":108,"unit":"g","stated":"Weight (Sight Only): 108 g / 3.8 oz","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Duty RDS spec sheet for item 200759 (Ed. 7-May-21), the PDF as T.REX ARMS hosts it","url":"https://img.trex-arms.com/wp/uploads/2026/03/aimpoint-duty-rds-specs-2021-05-07.pdf","retrieved":"2026-10-19","via":"harvest"}},{"id":"manual","value":110,"unit":"g","stated":"Sight only 110 g  (3.9 oz)","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Duty RDS user manual ([16661-4], 2021, 2025), the PDF as T.REX ARMS hosts it","url":"https://img.trex-arms.com/wp/uploads/2026/03/aimpoint-duty-rds-user-manual-2025.pdf","retrieved":"2026-10-19","via":"harvest"}},{"id":"bcm","value":108,"unit":"g","stated":"Weight 3.8 oz / 108 g (sight only)","source":{"type":"spec","publisher":"retailer","name":"Bravo Company USA, Aimpoint Duty RDS Red Dot Sight - One-piece Torsion Nut Mount, 39mm (AIMPOINT-200759)","url":"https://bravocompanyusa.com/aimpoint-duty-rds-red-dot-sight-one-piece-torsion-nut-mount-39mm/","retrieved":"2026-10-19","via":"harvest"}}],"adopt":{"from":"sheet","reason":"The sheet printed for this item, which the sellers repeat; the manual's 110 g, two years newer, is kept beside it."},"note":"Two figures of the maker's: 108 g on the 2021 sheet (and on every seller's page), 110 g in the 2025 manual. Neither says whether the battery is in it."},"eye_relief":{"label":"Eye relief","kind":"length","measurements":[],"note":"None to state: the sheet says \"Eye Relief: Unlimited\" and the manual \"Eye relief Unlimited\". A red dot: the part states no eye point."},"ring_span":{"label":"The sight's length over its lens-cover rings, covers raised","kind":"length","measurements":[{"id":"profile-left","value":3.098,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aimpoint-duty-rds 7e64620fc910 (Aimpoint's 200759_Aimpoint_DutyRDS_ProfileLeft as Bravo Company shows it (10987): the sight on its one-piece torsion nut mount, 39 mm, straight left side, white ground, covers raised)","scaleRef":"scale from aimpoint-duty-rds.height = 2.6378 in (y-extent 832 px → 315.4 px/in)","method":"width of the traced outline (tools/trace.py); the outline's length with the raised lids and their hinges cut away: the front cover ring's end to the rear one's, at the axis's rows","via":"harvest"}},{"id":"trex-t2","value":3.066,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aimpoint-duty-rds 288f8fe3d5b6 (T.REX ARMS' guide, Final_-3: this sight and a Micro T-2, each on a Scalarworks mount of the same height, on one flat-top upper's rail, the rifle's right side; this sight's lids hang down, so its rings' ends are clear)","scaleRef":"the Micro T-2's own length over its cover rings, aimpoint-micro-t-2.ring_span (2.856 in), is 504 px in this photo (columns 963 to 1467 over the axis's rows): 176.5 px/in, the two sights standing on one rail at one distance from the lens","method":"this sight's rings' ends, columns 360 to 901 over the axis's rows (541 px): 1.073 times the T-2's. It rests on the T-2 in that photo having its covers' rings on, which its lidless ends look to have","via":"harvest"}}],"adopt":{"from":"profile-left","reason":"Aimpoint's own straight profile at the scale of the maker's 67 mm; T.REX's photo, scaled by the Micro T-2 beside it on the rail, reads 1.0% shorter, inside the two readings' ±."},"note":"What the side views show: both covers raised, the rubber rings round the two ends of the tube. Between the bare sight's 68 mm and the 80 mm with the covers closed. The check: T.REX's photo of this sight and a Micro T-2 on one rail (references/aimpoint-duty-rds 288f8fe3d5b6, the rifle's right side, the Duty RDS's lids hanging down so its rings' ends are clear) has this sight's length over its rings 541 px (columns 360 to 901, over the axis's rows) and the T-2's 504 (963 to 1467): 1.073 times. With the T-2's own length over its rings (aimpoint-micro-t-2.ring_span, 2.856 in) that is 3.066 in, 0.031 in (1.0%) under this reading; it rests on the T-2 in that photo having its covers' rings on, which its lidless ends look to have."},"axis_above_clamp_bottom":{"label":"Optical axis above the mount's bottom","kind":"length","measurements":[{"id":"profile-left","value":1.935,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/aimpoint-duty-rds 7e64620fc910 (Aimpoint's 200759_Aimpoint_DutyRDS_ProfileLeft as Bravo Company shows it (10987): the sight on its one-piece torsion nut mount, 39 mm, straight left side, white ground, covers raised)","scaleRef":"scale from aimpoint-duty-rds.height = 2.6378 in (y-extent 832 px → 315.4 px/in)","method":"centre between the top (max over 0.0 in windows) along x [1.48, 1.51] of the traced outline (tools/trace.py); the front cover ring's rounded end is round about the axis: the middle of its top and bottom edges over the last 0.03 in of the outline, above the mount's lowest row","via":"harvest"}}],"note":"Read at the front cover ring's rounded end, which is round about the axis. The rear ring's end reads 0.02 in lower in the same way (the photo leans a fraction of a degree, or the rear ring's rim isn't quite round where its hinge stands): inside this reading's ±, and the difference stays in clamp_below_rail."},"mount_length":{"label":"The mount's length along the rail","kind":"length","measurements":[{"id":"profile-left","value":2.045,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aimpoint-duty-rds 7e64620fc910 (Aimpoint's 200759_Aimpoint_DutyRDS_ProfileLeft as Bravo Company shows it (10987): the sight on its one-piece torsion nut mount, 39 mm, straight left side, white ground, covers raised)","scaleRef":"scale from aimpoint-duty-rds.height = 2.6378 in (y-extent 832 px → 315.4 px/in)","method":"median row width in y [0.45, 0.8] (2.045–2.051) of the traced outline (tools/trace.py); the mount's block along the rows between its jaw's chamfers and its top, under the sight's foot: its front face to its rear face, the median over its rows","via":"harvest"}}],"note":"No page gives it. Read on Aimpoint's left profile, the block under the sight's foot between its jaw's chamfers and its top; the sight's foot above it is within a few hundredths as long."},"ring_bottom_above_clamp_bottom":{"label":"The front cover ring's underside above the mount's bottom","kind":"length","measurements":[{"id":"profile-left","value":1.275,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/aimpoint-duty-rds 7e64620fc910 (Aimpoint's 200759_Aimpoint_DutyRDS_ProfileLeft as Bravo Company shows it (10987): the sight on its one-piece torsion nut mount, 39 mm, straight left side, white ground, covers raised)","scaleRef":"scale from aimpoint-duty-rds.height = 2.6378 in (y-extent 832 px → 315.4 px/in)","method":"y_min in x [1.25, 1.35] in y [0.5, 2.0] of the traced outline (tools/trace.py); the front cover ring's underside, ahead of the housing and above the mount","via":"harvest"}}]},"tube_od":{"label":"Front lens-cover ring's outside diameter","kind":"length","measurements":[{"id":"profile-left","value":1.32,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"2 * ({.axis_above_clamp_bottom} - {.ring_bottom_above_clamp_bottom})","via":"harvest"}}],"note":"Twice the ring's underside below the axis: its top is under the front cover's hinge."},"underside_above_clamp_bottom":{"label":"The sight's underside (the seam under its foot, the mount's top) above the mount's bottom","kind":"length","measurements":[{"id":"profile-left","value":0.906,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/aimpoint-duty-rds 7e64620fc910 (Aimpoint's own 200759_Aimpoint_DutyRDS_ProfileLeft as Bravo Company shows it: the sight on its 39 mm mount, straight left side, white ground, 1280 px, objective to the left, both covers raised)","scaleRef":"the configuration's height, height (67 mm), is the outline's 831 px in this photo (the mount's bottom, row 1223, to the housing's top, row 392): 315.0 px/in","method":"the dark line between the sight's foot and the mount's top, rows 936 to 940 down columns 400, 450, 560, 700 and 880 (its middle, row 938, is 285 px above the mount's lowest row)","via":"harvest"}}],"note":"The seam shows as a dark line across the whole foot in the left profile. The maker's 43 mm of sight under the housing's top would put it 0.039 in higher (sight_height)."},"jaw_top_above_clamp_bottom":{"label":"The line on the mount's left side where its jaw begins (the locking bar's top) above the mount's bottom","kind":"length","measurements":[{"id":"profile-left","value":0.502,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/aimpoint-duty-rds 7e64620fc910 (Aimpoint's own 200759_Aimpoint_DutyRDS_ProfileLeft as Bravo Company shows it: the sight on its 39 mm mount, straight left side, white ground, 1280 px, objective to the left, both covers raised)","scaleRef":"the configuration's height, height (67 mm), is the outline's 831 px in this photo: 315.0 px/in","method":"the edge across the mount's left side at row 1065, from the front face to the rear, over the locking bar's top: 158 px above the mount's lowest row","via":"harvest"}}]},"clamp_below_rail":{"label":"How far the mount reaches below the rail's top","kind":"length","measurements":[{"id":"derived","value":0.4,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.axis_above_clamp_bottom} - {.optical_axis_above_rail}","via":"harvest"}}],"note":"Nothing in a side view shows the rail's top inside the mount: it is where the sheet's 39 mm puts it under the tube's axis. The jaws then reach this far down beside the rail: more than the catalog's other clamps (0.22 to 0.25 in), about as far as the Micro T-2's LRP base (0.39 in)."},"clamp_bottom_y":{"label":"The mount's bottom in the optic frame (y, the rail's top is 0)","kind":"length","measurements":[{"id":"derived","value":-0.4,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"-{.clamp_below_rail}","via":"harvest"},"note":"Where the side profile's mount-bottom origin sits in the part frame."}]},"battery_cap_od":{"label":"The battery cap's diameter (on the right side)","kind":"length","measurements":[{"id":"profile-right","value":1.202,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aimpoint-duty-rds 0a07ac71a254 (Aimpoint's own 200759_Aimpoint_DutyRDS_ProfileRight as Bravo Company shows it: straight right side, white ground, 1280 px, objective to the right, both covers raised)","scaleRef":"the sight's length over its cover rings, ring_span, is 967 px in this photo (columns 155 to 1122): 312.1 px/in at its 3.098 in","method":"the cap is a circle in this view: columns 572 to 947 along its middle row (its rim's shadow on the left, the dip at the ring's side on the right), its bottom edge's shadow at row 824: 375 px across. Read in px and scaled by ring_span: 375 / 967 of it","via":"harvest"}}]},"battery_cap_from_front":{"label":"The battery cap's centre behind the front cover ring's end","kind":"length","measurements":[{"id":"profile-right","value":1.16,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aimpoint-duty-rds 0a07ac71a254 (Aimpoint's own 200759_Aimpoint_DutyRDS_ProfileRight as Bravo Company shows it: straight right side, white ground, 1280 px, objective to the right, both covers raised)","scaleRef":"the sight's length over its cover rings, ring_span, is 967 px in this photo (columns 155 to 1122): 312.1 px/in at its 3.098 in","method":"the circle's centre, column 760, from the front ring's end, column 1122: 362 px, 362 / 967 of ring_span","via":"harvest"}}]},"battery_cap_below_axis":{"label":"The battery cap's centre below the optical axis","kind":"length","measurements":[{"id":"profile-right","value":0.083,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aimpoint-duty-rds 0a07ac71a254 (Aimpoint's own 200759_Aimpoint_DutyRDS_ProfileRight as Bravo Company shows it: straight right side, white ground, 1280 px, objective to the right, both covers raised)","scaleRef":"the sight's length over its cover rings, ring_span, is 967 px in this photo (columns 155 to 1122): 312.1 px/in at its 3.098 in","method":"the circle's centre, row 637, below the axis's row at the front ring's end, 611 (the middle of the rim's rows at columns 1117 to 1122): 26 px","via":"harvest"}}]},"windage_od":{"label":"The windage adjuster's diameter (flush in the right side, behind the cap)","kind":"length","measurements":[{"id":"profile-right","value":0.497,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aimpoint-duty-rds 0a07ac71a254 (Aimpoint's own 200759_Aimpoint_DutyRDS_ProfileRight as Bravo Company shows it: straight right side, white ground, 1280 px, objective to the right, both covers raised)","scaleRef":"the sight's length over its cover rings, ring_span, is 967 px in this photo (columns 155 to 1122): 312.1 px/in at its 3.098 in","method":"the round recess the steel disc sits in: its dark rim at columns 394 and 550 along row 637, rows 558 and 712 down column 472: 156 and 154 px","via":"harvest"}}]},"windage_from_front":{"label":"The windage adjuster's centre behind the front cover ring's end","kind":"length","measurements":[{"id":"profile-right","value":2.083,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aimpoint-duty-rds 0a07ac71a254 (Aimpoint's own 200759_Aimpoint_DutyRDS_ProfileRight as Bravo Company shows it: straight right side, white ground, 1280 px, objective to the right, both covers raised)","scaleRef":"the sight's length over its cover rings, ring_span, is 967 px in this photo (columns 155 to 1122): 312.1 px/in at its 3.098 in","method":"the circle's centre, column 472, from the front ring's end, column 1122: 650 px","via":"harvest"}}]},"windage_below_axis":{"label":"The windage adjuster's centre below the optical axis","kind":"length","measurements":[{"id":"profile-right","value":0.077,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aimpoint-duty-rds 0a07ac71a254 (Aimpoint's own 200759_Aimpoint_DutyRDS_ProfileRight as Bravo Company shows it: straight right side, white ground, 1280 px, objective to the right, both covers raised)","scaleRef":"the sight's length over its cover rings, ring_span, is 967 px in this photo (columns 155 to 1122): 312.1 px/in at its 3.098 in","method":"the circle's centre, row 635, below the axis's row at the front ring's end, 611: 24 px","via":"harvest"}}]},"groove_top_above_clamp_bottom":{"label":"The top of the groove along the mount's right side, above the mount's bottom","kind":"length","measurements":[{"id":"profile-right","value":0.811,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aimpoint-duty-rds 0a07ac71a254 (Aimpoint's own 200759_Aimpoint_DutyRDS_ProfileRight as Bravo Company shows it: straight right side, white ground, 1280 px, objective to the right, both covers raised)","scaleRef":"the sight's length over its cover rings, ring_span, is 967 px in this photo (columns 155 to 1122): 312.1 px/in at its 3.098 in","method":"the groove's upper edge, row 965, under the lip below the sight's foot, 253 px above the mount's lowest row (1218), scaled as above","via":"harvest"}}]},"groove_bottom_above_clamp_bottom":{"label":"The bottom of the groove along the mount's right side, above the mount's bottom","kind":"length","measurements":[{"id":"profile-right","value":0.49,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aimpoint-duty-rds 0a07ac71a254 (Aimpoint's own 200759_Aimpoint_DutyRDS_ProfileRight as Bravo Company shows it: straight right side, white ground, 1280 px, objective to the right, both covers raised)","scaleRef":"the sight's length over its cover rings, ring_span, is 967 px in this photo (columns 155 to 1122): 312.1 px/in at its 3.098 in","method":"the groove's lower edge, row 1065, where the jaw's face begins: 153 px above the mount's lowest row","via":"harvest"}}]},"groove_depth":{"label":"How deep the groove along the mount's right side is cut","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows the groove in section (the quarter views show it as a shadowed hollow along the side).","via":"harvest"}}]},"shoulder_radius":{"label":"The round of the housing's shoulders (where its flanks turn over into its top)","kind":"length","measurements":[{"id":"assumed","value":0.2,"unit":"in","pm":0.08,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view along the sight is on file; the quarter views show the flanks turning over into the top in a round about this size against the cover rings.","via":"harvest"}}]},"lock_screw_proud":{"label":"How far the locking bar's screw head stands out of the bar","kind":"length","measurements":[{"id":"assumed","value":0.04,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the quarter views show a button head standing out of the bar; how far isn't read.","via":"harvest"}}]},"adjuster_proud":{"label":"How far the windage and elevation adjusters' steel discs stand out of the housing","kind":"length","measurements":[{"id":"assumed","value":0.01,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the sheet calls them \"FLUSH-MOUNTED WINDAGE & ELEVATION ADJUSTMENTS\"; drawn a hair proud so the steel shows.","via":"harvest"}}]},"keypad_recess":{"label":"How far the keypad's button face lies inside its raised ring","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the quarter views show the button face set in its ring; how far isn't read.","via":"harvest"}}]},"cap_slot_length":{"label":"The coin slot across the battery cap: its length, end to end","kind":"length","measurements":[{"id":"profile-right","value":0.65,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aimpoint-duty-rds 0a07ac71a254 (Aimpoint's own 200759_Aimpoint_DutyRDS_ProfileRight as Bravo Company shows it: straight right side, white ground, 1280 px, objective to the right, both covers raised)","scaleRef":"the sight's length over its cover rings, ring_span, is 967 px in this photo (columns 155 to 1122): 312.1 px/in at its 3.098 in","method":"the slot's two rounded ends, at about (685, 580) and (838, 710) in the photo, falling toward the front at about 40 degrees: 201 px","via":"harvest"}}]},"cap_slot_width":{"label":"The coin slot's width","kind":"length","measurements":[{"id":"profile-right","value":0.11,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aimpoint-duty-rds 0a07ac71a254 (Aimpoint's own 200759_Aimpoint_DutyRDS_ProfileRight as Bravo Company shows it: straight right side, white ground, 1280 px, objective to the right, both covers raised)","scaleRef":"the sight's length over its cover rings, ring_span, is 967 px in this photo (columns 155 to 1122): 312.1 px/in at its 3.098 in","method":"across the slot square to its length, its shadowed wall and its lit one together: about 34 px","via":"harvest"}}]},"cap_slot_depth":{"label":"How deep the coin slot is cut into the cap","kind":"length","measurements":[{"id":"assumed","value":0.04,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view shows the slot in section.","via":"harvest"}}]}}},{"subject":"aimpoint-micro-lrp-39mm","title":"Aimpoint LRP (Lever Release Picatinny) mount with the 39 mm spacer, for the Micro footprint","dimensions":{"deck_above_rail":{"label":"The deck's top (the spacer's top, where a dot's base sits) above the rail's top","kind":"length","measurements":[{"id":"sheet-less-t2","value":0.9464,"unit":"in","pm":0.037,"source":{"type":"derived","expr":"{aimpoint-micro-t-2.optical_axis_above_rail} - {aimpoint-micro-t-2.axis_above_base}","via":"harvest"},"note":"39 mm (1.535 in) less the T-2's 0.589 in."}],"note":"Aimpoint gives the mount's height only as the axis height of the Micro T-2 on it: \"Sight, mount and high spacer – 39 mm ... measured from top surface of Picatinny/Weaver rail\" (the sheet for 200198). Less the T-2's own axis over its base it is the deck's height; another Micro-footprint dot on it stands as much higher or lower as its own axis is over its base (D101)."},"deck_x":{"label":"The footprint's middle along the deck, ahead of the clamp's middle","kind":"length","measurements":[{"id":"assumed","value":0,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view shows the footprint's screws or lug. Their middle is taken to be the spacer block's, which is where the frame's origin is along the rail (the side outline's origin is the block's middle over its rows: aimpoint-micro-t-2's profiles.side), with the LRP base about it as the part before the split had it."}}]},"mount_length":{"label":"The LRP base's length along the rail (without the lever's tip)","kind":"length","measurements":[{"id":"lrp-left","value":2.036,"unit":"in","pm":0.023,"source":{"type":"derived","expr":"{aimpoint-micro-t-2.mount_length}","via":"harvest"},"note":"Read on Aimpoint's left profile of the pair, in the sight's ledger."}]},"clamp_below_rail":{"label":"How far the LRP base reaches below the rail's top","kind":"length","measurements":[{"id":"lrp-left","value":0.392,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{aimpoint-micro-t-2.clamp_below_rail}","via":"harvest"},"note":"Where the sheet's 39 mm puts the rail's top under the axis of the pair: the sight's ledger says how."}]},"weight":{"label":"Weight (the mount and the 39 mm spacer)","kind":"mass","measurements":[{"id":"sheet-less-sight","value":34,"unit":"g","pm":1,"source":{"type":"derived","expr":"{aimpoint-micro-t-2.weight} - {aimpoint-micro-t-2.sight_weight}","via":"harvest"},"note":"130 g less 96 g."},{"id":"metal","value":112,"unit":"g","pm":3,"source":{"type":"derived","basis":"The model's volume as solid aluminium: 2.516 cubic inches (the spacer 1.703, the base 0.763, the lever 0.050: pipeline/blender/aimpoint_micro_t_2.py's manifest) times std.density.aluminium (0.098 lb a cubic inch). A ceiling: the spacer's side hollows aren't cut, and the lever's nut is steel."}}],"adopt":{"from":"sheet-less-sight","reason":"The figure the pair had before the split, carried to the mount, so that no build's weight moves; the solid model's metal is kept as the ceiling, and the span of the two is the build's weight range."},"note":"No page on file weighs the LRP mount or the 39 mm spacer. Before the split the pair was weighed at the sheet's 130 g, kept there as a floor (the sheet prints it beside the standard configuration's size: aimpoint-micro-t-2.weight); what that leaves over the sight's own 96 g is this mount's floor, so a build's weight doesn't move with the split. Its metal as modelled is the ceiling: the spacer is a plain block in the model, its hollows not cut."}}},{"subject":"aimpoint-micro-t-2","title":"Aimpoint Micro T-2 Red Dot Reflex Sight (the sight: 200180), with the readings of Aimpoint's pictures of it on its LRP mount and the 39 mm spacer (200198)","dimensions":{"length":{"label":"Overall length (with its lens covers, closed)","kind":"length","measurements":[{"id":"sheet","value":79,"unit":"mm","stated":"Size L x W x H (mm) Conf: 79 x 41 x 47 mm","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Micro T-2 spec sheet for item 200198 (M03616, Ed. 5-October-21), the PDF as T.REX ARMS hosts it","url":"https://img.trex-arms.com/wp/uploads/2026/03/aimpoint-micro-t2-specs-2021-10-05.pdf","retrieved":"2026-10-06","via":"harvest"}},{"id":"manual","value":79,"unit":"mm","stated":"Configuration 79 mm × 41 mm × 48 mm","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Micro T-2 user manual ([13939-7], 2014, 2025), the PDF as T.REX ARMS hosts it: the sight on the standard mount (its Fig. 1)","url":"https://img.trex-arms.com/wp/uploads/2026/03/aimpoint-micro-t2-user-manual-2025.pdf","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"sheet","reason":"The sheet printed for this item; the manual gives the same length."},"note":"The sheet's and the manual's \"Conf\" length: the sight with its lens covers (\"Includes lens covers & mount\"). Neither mount reaches past the covers in the side views, so it is this stack's length too. Scalarworks' side view of a T-2 with its covers closed, on a rail whose pitch scales it, reads 77.2 mm between the lids' faces and 78.1 to the rear lid's tab. With the covers raised, as every studio view has them and as the model is drawn, the sight is ring_span long."},"sight_length":{"label":"The sight's own length, without its lens covers","kind":"length","measurements":[{"id":"sheet","value":68,"unit":"mm","stated":"Size L x W x H (mm) Sight Only: 68 x 41 x 36 mm","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Micro T-2 spec sheet for item 200198 (M03616, Ed. 5-October-21), the PDF as T.REX ARMS hosts it","url":"https://img.trex-arms.com/wp/uploads/2026/03/aimpoint-micro-t2-specs-2021-10-05.pdf","retrieved":"2026-10-06","via":"harvest"}},{"id":"manual","value":68,"unit":"mm","stated":"Sight 68 mm × 41 mm × 36 mm","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Micro T-2 user manual ([13939-7], 2014, 2025), the PDF as T.REX ARMS hosts it: the sight on the standard mount (its Fig. 1)","url":"https://img.trex-arms.com/wp/uploads/2026/03/aimpoint-micro-t2-user-manual-2025.pdf","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"sheet","reason":"The sheet printed for this item; the manual gives the same."},"note":"\"Sight Only\": the bare sight, without the rubber lens covers whose rings wrap its two ends (the configuration's figures are the ones that include \"lens covers & mount\"). Not seen in any photo on file: every one has the covers on."},"width":{"label":"Overall width (the sight's own: its left flank to the face of the intensity switch on its right)","kind":"length","measurements":[{"id":"sheet","value":41,"unit":"mm","stated":"Size L x W x H (mm) Conf: 79 x 41 x 47 mm","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Micro T-2 spec sheet for item 200198 (M03616, Ed. 5-October-21), the PDF as T.REX ARMS hosts it","url":"https://img.trex-arms.com/wp/uploads/2026/03/aimpoint-micro-t2-specs-2021-10-05.pdf","retrieved":"2026-10-06","via":"harvest"}},{"id":"manual","value":41,"unit":"mm","stated":"Configuration 79 mm × 41 mm × 48 mm","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Micro T-2 user manual ([13939-7], 2014, 2025), the PDF as T.REX ARMS hosts it: the sight on the standard mount (its Fig. 1)","url":"https://img.trex-arms.com/wp/uploads/2026/03/aimpoint-micro-t2-user-manual-2025.pdf","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"sheet","reason":"The sheet printed for this item; the manual gives the same."},"note":"The same 41 mm for the sight alone and for the configuration, so it is the sight's: neither says what it spans, and it is taken from the flat left flank to the face of the intensity switch, the furthest thing out on the right. The LRP mount's lever and its nut on the left may stand further out than the sight: its own width is on no page on file."},"sight_height":{"label":"The sight's own height (its underside to the top of the turret housing)","kind":"length","measurements":[{"id":"sheet","value":36,"unit":"mm","stated":"Size L x W x H (mm) Sight Only: 68 x 41 x 36 mm","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Micro T-2 spec sheet for item 200198 (M03616, Ed. 5-October-21), the PDF as T.REX ARMS hosts it","url":"https://img.trex-arms.com/wp/uploads/2026/03/aimpoint-micro-t2-specs-2021-10-05.pdf","retrieved":"2026-10-06","via":"harvest"}},{"id":"manual","value":36,"unit":"mm","stated":"Sight 68 mm × 41 mm × 36 mm","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Micro T-2 user manual ([13939-7], 2014, 2025), the PDF as T.REX ARMS hosts it: the sight on the standard mount (its Fig. 1)","url":"https://img.trex-arms.com/wp/uploads/2026/03/aimpoint-micro-t2-user-manual-2025.pdf","retrieved":"2026-10-06","via":"harvest"}},{"id":"lrp-left","value":1.401,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.height} - {.underside_above_clamp_bottom}","via":"harvest"},"note":"On the photo: the turret housing's top 2.739 in above the mount's bottom, and the sight's underside where the maker's 19 mm of spacer puts it over the base's top, 1.338 in: 35.6 mm."}],"adopt":{"from":"sheet","reason":"The sheet printed for this item; the manual gives the same, and the photo reads within 1% of it."},"note":"From the sight's flat underside to the top of the housing round the elevation turret. Aimpoint's left profile of this part, at the scale the standard-mount photo gives, has the housing's top 35.6 mm above the underside as the maker's 19 mm of spacer places it: 1% under the maker's figure, inside its rounding. The model is drawn at the photo's size."},"standard_conf_height":{"label":"Height of the STANDARD configuration (200170: the low mount's bottom to the sight's top), not this part's","kind":"length","measurements":[{"id":"sheet","value":47,"unit":"mm","stated":"Size L x W x H (mm) Conf: 79 x 41 x 47 mm","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Micro T-2 spec sheet for item 200198 (M03616, Ed. 5-October-21), the PDF as T.REX ARMS hosts it","url":"https://img.trex-arms.com/wp/uploads/2026/03/aimpoint-micro-t2-specs-2021-10-05.pdf","retrieved":"2026-10-06","via":"harvest"}},{"id":"manual","value":48,"unit":"mm","stated":"Configuration 79 mm × 41 mm × 48 mm","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Micro T-2 user manual ([13939-7], 2014, 2025), the PDF as T.REX ARMS hosts it: the sight on the standard mount (its Fig. 1)","url":"https://img.trex-arms.com/wp/uploads/2026/03/aimpoint-micro-t2-user-manual-2025.pdf","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"sheet","reason":"At 47 mm the standard-mount photo's scale lands on a Picatinny rail's pitch in Scalarworks' side view of the same sight within 0.5%; at the manual's 48 it is 2% off. Two documents of the maker's that differ by a millimetre: both kept."},"note":"Printed on this item's own sheet as its \"Conf\" height, but it is the standard mount's: the scale of the standard-mount side photo, from which the sight's own sizes are read. The sheet says 47 mm and the manual 48."},"standard_axis_above_rail":{"label":"Optical axis above the rail on the STANDARD mount (200170), not this part's","kind":"length","measurements":[{"id":"sheet","value":20,"unit":"mm","stated":"Height of Optical Axis: Sight and mount – 20 mm (0.8 in) measured from top surface of Picatinny/Weaver rail","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Micro T-2 spec sheet for item 200198 (M03616, Ed. 5-October-21), the PDF as T.REX ARMS hosts it","url":"https://img.trex-arms.com/wp/uploads/2026/03/aimpoint-micro-t2-specs-2021-10-05.pdf","retrieved":"2026-10-06","via":"harvest"}},{"id":"manual","value":20,"unit":"mm","stated":"Configuration (no spacer) 20 mm / 0.8 in (measured from top surface of picatinny rail)","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Micro T-2 user manual ([13939-7], 2014, 2025), the PDF as T.REX ARMS hosts it: the sight on the standard mount (its Fig. 1)","url":"https://img.trex-arms.com/wp/uploads/2026/03/aimpoint-micro-t2-user-manual-2025.pdf","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"sheet","reason":"The sheet printed for this item; the manual gives the same."},"note":"The other listing's figure, kept so the two aren't confused: too low for an AR-15's stock. The 39 mm spacer adds the difference."},"optical_axis_above_rail":{"label":"Optical axis above the rail's top (on the LRP mount with the 39 mm spacer)","kind":"length","measurements":[{"id":"sheet","value":39,"unit":"mm","stated":"Sight, mount and high spacer – 39 mm (1.2 in) measured from top surface of Picatinny/Weaver rail","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Micro T-2 spec sheet for item 200198 (M03616, Ed. 5-October-21), the PDF as T.REX ARMS hosts it","url":"https://img.trex-arms.com/wp/uploads/2026/03/aimpoint-micro-t2-specs-2021-10-05.pdf","retrieved":"2026-10-06","via":"harvest"}}],"note":"The sheet's line for \"sight, mount and high spacer\", and what the spacer is named for. Its inch figure is wrong: 39 mm is 1.54 in (the \"1.2 in\" is the 30 mm line's, printed twice). Its \"Keyed Surface Mount: LRP Mount and 39 mm spacer included\" says which mount and spacer this item has; Bravo Company: \"The AR15 Ready configuration includes a 39mm spacer and LRP (Lever Release Picatinny) base\". Where the rail's top lies inside the LRP mount isn't seen in a side view: the model's rail top is this far under the axis."},"axis_above_base":{"label":"Optical axis above the sight's own base (the plane its footprint meets a mount's deck in: D101)","kind":"length","measurements":[{"id":"lrp-left","value":0.589,"unit":"in","pm":0.037,"source":{"type":"derived","expr":"{.axis_above_clamp_bottom} - {.underside_above_clamp_bottom}","via":"harvest"},"note":"1.927 in less 1.338 in, the two readings' ± together."}],"note":"What the sight brings to any Micro-footprint mount (D101): its axis this far over the deck it is screwed to. Read on Aimpoint's left profile of 200198 between the axis and the seam with the spacer, which the maker's two axis heights place (underside_above_clamp_bottom). On the LRP mount with the 39 mm spacer it puts the axis at the sheet's 39 mm, which is what the mount's deck height is worked out from (aimpoint-micro-lrp-39mm.deck_above_rail)."},"window_d":{"label":"Clear aperture","kind":"length","measurements":[{"id":"sheet","value":18,"unit":"mm","stated":"Clear Aperture: 18 mm (.71 in)","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Micro T-2 spec sheet for item 200198 (M03616, Ed. 5-October-21), the PDF as T.REX ARMS hosts it","url":"https://img.trex-arms.com/wp/uploads/2026/03/aimpoint-micro-t2-specs-2021-10-05.pdf","retrieved":"2026-10-06","via":"harvest"}},{"id":"manual","value":18,"unit":"mm","stated":"Clear aperture 18 mm","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Micro T-2 user manual ([13939-7], 2014, 2025), the PDF as T.REX ARMS hosts it: the sight on the standard mount (its Fig. 1)","url":"https://img.trex-arms.com/wp/uploads/2026/03/aimpoint-micro-t2-user-manual-2025.pdf","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"sheet","reason":"The sheet printed for this item; the manual gives the same."},"note":"Draws the lens at both ends; the front lens is tilted in its cell (the manual: \"The optical system is designed for the front lens to be mounted this way\") and is drawn square."},"weight":{"label":"Weight (the sheet's configuration figure: lens covers and mount in it; the LRP stack's own isn't published)","kind":"mass","measurements":[{"id":"sheet","value":130,"unit":"g","stated":"Weight (Conf): 130 g / 4.6 oz (Includes lens covers & mount)","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Micro T-2 spec sheet for item 200198 (M03616, Ed. 5-October-21), the PDF as T.REX ARMS hosts it","url":"https://img.trex-arms.com/wp/uploads/2026/03/aimpoint-micro-t2-specs-2021-10-05.pdf","retrieved":"2026-10-06","via":"harvest"}},{"id":"manual","value":135,"unit":"g","stated":"Configuration 135 g / 4.8 oz","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Micro T-2 user manual ([13939-7], 2014, 2025), the PDF as T.REX ARMS hosts it: the sight on the standard mount (its Fig. 1)","url":"https://img.trex-arms.com/wp/uploads/2026/03/aimpoint-micro-t2-user-manual-2025.pdf","retrieved":"2026-10-06","via":"harvest"},"note":"The manual's configuration: the sight on the standard mount (its Fig. 1)."},{"id":"mhs-table","value":139,"unit":"g","stated":"Weight sight with integrated mount 139g, (4.9oz)","source":{"type":"spec","publisher":"retailer","name":"Mile High Shooting, AimPoint 200198: Micro T-2 2MOA LRP (its table is the standard-mount listing's: its Article Number row says 200170)","url":"https://www.milehighshooting.com/aimpoint-200198-micro-t-2-2moa-lrp/","retrieved":"2026-10-06","via":"harvest"},"note":"On the 200198 page, in a table whose Article Number row says 200170."},{"id":"mhs-prose","value":105,"unit":"g","stated":"Weight 3.7 oz. (105g) including mount, sight only 3.0 oz. (84g)","source":{"type":"spec","publisher":"retailer","name":"Mile High Shooting, AimPoint 200198: Micro T-2 2MOA LRP (its table is the standard-mount listing's: its Article Number row says 200170)","url":"https://www.milehighshooting.com/aimpoint-200198-micro-t-2-2moa-lrp/","retrieved":"2026-10-06","via":"harvest"},"note":"The same page's prose; which mount isn't said."}],"adopt":{"from":"sheet","reason":"The only figure the maker prints on this item's own sheet, and it says what it includes; the others are the standard configuration's or a seller's copy. It is kept as a floor, not as the LRP stack's weight: see the note."},"note":"No page on file weighs the sight on the LRP mount and the 39 mm spacer. The sheet printed for 200198 says 130 g for its \"Conf\", beside a configuration size (79 x 41 x 47 mm) that is the low standard mount's: the 130 g is probably that configuration's too, and this stack, with a spacer and a lever mount of aluminium under it, heavier. The manual's standard configuration is 135 g; Mile High's page for 200198 carries the standard listing's table (139 g \"with integrated mount\") and, in its prose, 105 g \"including mount\". A seller's weight for the 200198 stack itself is a gap."},"sight_weight":{"label":"Weight of the sight alone (200180), not this part's","kind":"mass","measurements":[{"id":"manual","value":96,"unit":"g","stated":"Sight (incl. battery) 96 g / 3.4 oz","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Micro T-2 user manual ([13939-7], 2014, 2025), the PDF as T.REX ARMS hosts it: the sight on the standard mount (its Fig. 1)","url":"https://img.trex-arms.com/wp/uploads/2026/03/aimpoint-micro-t2-user-manual-2025.pdf","retrieved":"2026-10-06","via":"harvest"}},{"id":"sheet-p2","value":94,"unit":"g","stated":"Weight (Sight Only): 94 g / 3.3 oz","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Micro T-2 spec sheet for item 200198 (M03616, Ed. 5-October-21), the PDF as T.REX ARMS hosts it","url":"https://img.trex-arms.com/wp/uploads/2026/03/aimpoint-micro-t2-specs-2021-10-05.pdf","retrieved":"2026-10-06","via":"harvest"}},{"id":"sheet-p1","value":84,"unit":"g","stated":"Weight 3.0 oz / 84 g (sight only).","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Micro T-2 spec sheet for item 200198 (M03616, Ed. 5-October-21), the PDF as T.REX ARMS hosts it","url":"https://img.trex-arms.com/wp/uploads/2026/03/aimpoint-micro-t2-specs-2021-10-05.pdf","retrieved":"2026-10-06","via":"harvest"}},{"id":"bcm","value":84,"unit":"g","stated":"Weight 3.0 oz / 84 g (sight only)","source":{"type":"spec","publisher":"retailer","name":"Bravo Company USA, Aimpoint Micro T-2 Red Dot Reflex Sight - AR15 Ready (AIMPOINT-200198)","url":"https://bravocompanyusa.com/micro-t-2-2-moa-red-dot-reflex-sight-with-39-mm-spacer-lrp-mount/","retrieved":"2026-10-06","via":"harvest"}},{"id":"trex","value":96,"unit":"g","stated":"Weight (including battery) 3.4 oz (96 g)","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, Aimpoint Micro T-2 Red Dot Sight (the sight with no mount)","url":"https://www.trex-arms.com/store/aimpoint-t2/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"manual","reason":"The newest of the maker's documents and the one that says what is in it (the battery); the sheet's two pages disagree with each other."},"note":"Three figures of the maker's for the sight alone: 84 g on the sheet's first page (and on Bravo Company's and T.REX ARMS' pages), 94 g on its second, 96 g \"incl. battery\" in the manual. Only the last says what is in it."},"eye_relief":{"label":"Eye relief","kind":"length","measurements":[],"note":"None to state: the sheet says \"Eye Relief: Unlimited\" and the manual \"Unlimited\". A red dot: the part states no eye point."},"height":{"label":"Overall height (the LRP mount's bottom to the top of the turret housing, covers left out)","kind":"length","measurements":[{"id":"lrp-left","value":2.739,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aimpoint-micro-t-2 10c377094e97 (Aimpoint's 200198_Micro_T-2_AR15_Ready_Profile_Left as Bravo Company shows it (10970): the sight on the 39 mm spacer and the LRP mount, straight left side, transparent ground, covers raised)","scaleRef":"scale from aimpoint-micro-t-2.ring_span = 2.856 in (x-extent 1119 px → 391.8 px/in)","method":"height of the traced outline (tools/trace.py); the LRP mount's lowest row to the top of the turret housing, the raised lids cut away","via":"harvest"}}],"note":"Not published for this stack (the sheet's 47 mm is the standard mount's): read off Aimpoint's left profile."},"ring_span":{"label":"The sight's length over its lens-cover rings, covers raised","kind":"length","measurements":[{"id":"gritr-left","value":2.856,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aimpoint-micro-t-2 4a3b89d486f8 (GRITR Outdoors 839216: the sight on the standard mount (200170), straight left side on white, covers raised)","scaleRef":"scale from aimpoint-micro-t-2.standard_conf_height = 1.85039 in (y-extent 865 px → 467.5 px/in)","method":"width of the traced outline (tools/trace.py); the outline's length with the raised lids and their hinges cut away: the front cover ring's end to the rear one's","via":"harvest"}}],"note":"What the side views show: both covers raised, the rubber rings round the two ends of the tube. Between the bare sight's 68 mm and the 79 mm with the covers closed. It is read on the standard-mount photo (GRITR 839216, 200170), the one whose whole height the maker publishes: the sheet's 47 mm from that mount's bottom to the top of the turret housing. Checked on a rail: Scalarworks' side view of a T-2 on its LEAP mount (990c8c035f13) has a Picatinny rail under it whose lands and slots repeat at 89 px (a land from column 405 to 449 and a slot back to 360 on the left; a land from 803 to 846 and a slot to 892 on the right), 8.89 px/mm; the sight in it is 1.72 to 1.73 times smaller than in Aimpoint's left profile of 200198 (the turret housing's top to the lettering's foot, 296 px against 513; the cover rings' diameters), and that profile 1.193 to 1.196 times smaller than GRITR's photo (the length over the rings, 1119 px against 1334; the housing's top to the axis): 18.2 to 18.4 px/mm for GRITR's photo by the rail, 18.4 by the 47 mm. The manual's 48 mm would make it 18.0. And on this part's own photo the scale lands the maker's 36 mm of sight and 19 mm of spacer together within 0.4 mm (sight_height). This length scales Aimpoint's two profiles of the part."},"axis_above_clamp_bottom":{"label":"Optical axis above the LRP mount's bottom","kind":"length","measurements":[{"id":"lrp-left","value":1.927,"unit":"in","pm":0.022,"source":{"type":"photo","photo":"references/aimpoint-micro-t-2 10c377094e97 (Aimpoint's 200198_Micro_T-2_AR15_Ready_Profile_Left as Bravo Company shows it (10970): the sight on the 39 mm spacer and the LRP mount, straight left side, transparent ground, covers raised)","scaleRef":"scale from aimpoint-micro-t-2.ring_span = 2.856 in (x-extent 1119 px → 391.8 px/in)","method":"centre between the top (max over 0.0 in windows) along x [1.395, 1.435] of the traced outline (tools/trace.py); the front cover ring's rounded end is round about the axis: the middle of its top and bottom edges over the last 0.04 in of the outline, above the mount's lowest row","via":"harvest"}}],"note":"Read at the front cover ring's rounded end, which is round about the axis. The rear ring's end reads 1.941 in the same way, 0.014 in higher (the photo leans a third of a degree, or the rear ring's rim isn't quite round where its hinge was cut away): inside this reading's ±, and the difference stays in clamp_below_rail."},"mount_length":{"label":"LRP mount's length along the rail (its base, without the lever's tip)","kind":"length","measurements":[{"id":"lrp-left","value":2.036,"unit":"in","pm":0.023,"source":{"type":"photo","photo":"references/aimpoint-micro-t-2 10c377094e97 (Aimpoint's 200198_Micro_T-2_AR15_Ready_Profile_Left as Bravo Company shows it (10970): the sight on the 39 mm spacer and the LRP mount, straight left side, transparent ground, covers raised)","scaleRef":"scale from aimpoint-micro-t-2.ring_span = 2.856 in (x-extent 1119 px → 391.8 px/in)","method":"median row width in y [0.02, 0.035] (2.018–2.045) of the traced outline (tools/trace.py); the LRP base along its lowest rows, under the lever","via":"harvest"}}]},"tube_od":{"label":"Front lens-cover ring's outside diameter (the widest ring of the tube)","kind":"length","measurements":[{"id":"lrp-left","value":1.218,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/aimpoint-micro-t-2 10c377094e97 (Aimpoint's own 200198_Micro_T-2_AR15_Ready_Profile_Left as Bravo Company shows it: the sight on the 39 mm spacer and the LRP mount, straight left side, transparent ground, 1600 x 1600, objective to the left, both covers raised)","scaleRef":"the sight's length over its cover rings, ring_span (2.856 in), is 1119 px in this photo: 391.8 px/in","method":"the front ring's underside, rows 1003 to 1004 over columns 388 to 413, is 1.318 in above the mount's lowest row (1520) and 0.609 in below the axis (axis_above_clamp_bottom, 1.927 in): twice that","via":"harvest"}}],"note":"Twice the ring's underside below the axis: its top is under the front cover's hinge. The rear ring is smaller (its underside 0.51 in below the axis)."},"shoulder_radius":{"label":"The round of the housing's shoulders (where its flanks turn over into its top)","kind":"length","measurements":[{"id":"lrp-left","value":0.26,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/aimpoint-micro-t-2 10c377094e97 (Aimpoint's own 200198_Micro_T-2_AR15_Ready_Profile_Left as Bravo Company shows it: the sight on the 39 mm spacer and the LRP mount, straight left side, transparent ground, 1600 x 1600, objective to the left, both covers raised)","scaleRef":"the sight's length over its cover rings, ring_span (2.856 in), is 1119 px in this photo: 391.8 px/in","method":"brightness down the left flank ahead of the turret housing (the three channels' mean over 13 columns) at columns 480, 560 and 640: even, 55 to 64, below rows 640, 664 and 624; falling steadily above them to about 30 by rows 592, 584 and 568; dark from there to the housing's top edge (rows 548, 544, 536). The flank is flat up to 92, 120 and 88 px under the top edge and turns over above that: 0.23, 0.31 and 0.22 in","via":"harvest"}}],"note":"Read from the shading, since no view along the sight is on file: a flat flank is one tone in a side view, and a round over it darkens toward the top. It says how high the flat of the flank reaches; that the round is a quarter circle of that size, as wide as it is high, is assumed."},"spacer_length":{"label":"The 39 mm spacer block's length (front face to rear face)","kind":"length","measurements":[{"id":"lrp-left","value":1.922,"unit":"in","pm":0.022,"source":{"type":"photo","photo":"references/aimpoint-micro-t-2 10c377094e97 (Aimpoint's 200198_Micro_T-2_AR15_Ready_Profile_Left as Bravo Company shows it (10970): the sight on the 39 mm spacer and the LRP mount, straight left side, transparent ground, covers raised)","scaleRef":"scale from aimpoint-micro-t-2.ring_span = 2.856 in (x-extent 1119 px → 391.8 px/in)","method":"median row width in y [0.75, 1.15] (1.919–1.924) of the traced outline (tools/trace.py); the spacer block's front face to its rear face, the median over its rows","via":"harvest"}}]},"underside_above_clamp_bottom":{"label":"The sight's flat underside (the spacer's top) above the LRP mount's bottom","kind":"length","measurements":[{"id":"spacer","value":1.338,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.base_top_above_clamp_bottom} + {.optical_axis_above_rail} - {.standard_axis_above_rail}","via":"harvest"},"note":"The base's top on the photo, 0.590 in, and 19 mm."},{"id":"lrp-left","value":1.336,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aimpoint-micro-t-2 10c377094e97 (Aimpoint's 200198_Micro_T-2_AR15_Ready_Profile_Left as Bravo Company shows it (10970): the sight on the 39 mm spacer and the LRP mount, straight left side, transparent ground, covers raised)","scaleRef":"scale from aimpoint-micro-t-2.ring_span = 2.856 in (x-extent 1119 px → 391.8 px/in)","method":"the outline in the notch between the spacer's front face and the front cover ring's rear edge, 0.02 in ahead of the spacer. The housing's underside isn't flat there: it falls from 1.371 in at the spacer's face to 1.331 at the ring (the end of the pad the sight stands on), so this is a height on that slope, not the seam","via":"harvest"}}],"adopt":{"from":"spacer","reason":"The maker's two axis heights say how thick the spacer is; the photo's notch shows a slope and reads within 0.002 in of it at the point taken."},"note":"The seam between the sight and the spacer isn't seen in a side view (both are black, and the notch ahead of the spacer shows a slope). It is placed by the maker's own figures: the spacer adds 19 mm (39 mm with it, 20 without) over the LRP base's top, which the photo has. The maker's other figure agrees: its 36 mm of sight under the turret housing's top (2.739 in) puts the underside at 1.322 in, 0.4 mm lower."},"base_top_above_clamp_bottom":{"label":"The LRP base's top face (the spacer's foot) above the mount's bottom","kind":"length","measurements":[{"id":"lrp-left","value":0.59,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/aimpoint-micro-t-2 10c377094e97 (Aimpoint's 200198_Micro_T-2_AR15_Ready_Profile_Left as Bravo Company shows it (10970): the sight on the 39 mm spacer and the LRP mount, straight left side, transparent ground, covers raised)","scaleRef":"scale from aimpoint-micro-t-2.ring_span = 2.856 in (x-extent 1119 px → 391.8 px/in)","method":"y_max in x [-0.99, -0.97] in y [0.0, 0.9] of the traced outline (tools/trace.py); the LRP base's top face where it shows behind the spacer's rear face","via":"harvest"}}]},"clamp_below_rail":{"label":"How far the LRP mount reaches below the rail's top","kind":"length","measurements":[{"id":"derived","value":0.392,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.axis_above_clamp_bottom} - {.optical_axis_above_rail}","via":"harvest"}}],"note":"Nothing in a side view shows the rail's top inside the LRP base: it is where the sheet's 39 mm puts it under the tube's axis. That leaves 0.20 in (5 mm) of base over the rail and this much beside and under it, more than the catalog's other rail clamps reach (0.22 to 0.25 in); the low standard mount, read the same way on its own photo (the axis 1.06 in above its bottom, the sheet's 20 mm), reaches 0.27 in. One thing in the photos agrees with it: the socket in the base's right wall, a cross bolt's head at the middle of the base's length, is then centred 0.04 in below the rail's top (cross_bolt_below_axis), where a bolt lying in one of the rail's grooves would be."},"clamp_bottom_y":{"label":"LRP mount's bottom in the optic frame (y, the rail's top is 0)","kind":"length","measurements":[{"id":"derived","value":-0.392,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"-{.clamp_below_rail}","via":"harvest"},"note":"Where the side profile's mount-bottom origin sits in the part frame."}]},"spacer_height":{"label":"The 39 mm spacer's height (what it adds under the sight)","kind":"length","measurements":[{"id":"published","value":0.748,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.optical_axis_above_rail} - {.standard_axis_above_rail}","via":"harvest"},"note":"39 mm less 20 mm: 19 mm."}],"note":"What the maker's two axis heights leave between them: 39 mm with the high spacer, 20 mm without. It places the sight's underside over the LRP base's top (underside_above_clamp_bottom), and the sight's own 36 mm then agrees with the photo within 0.4 mm (sight_height)."},"intensity_od":{"label":"Intensity switch's diameter (its knurled ring, on the right side)","kind":"length","measurements":[{"id":"lrp-right","value":1.082,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aimpoint-micro-t-2 6738645c90b1 (Aimpoint's own 200198_Micro_T-2_AR15_Ready_Profile_Right as Bravo Company shows it: straight right side, transparent ground, 1600 x 1600, objective to the right, both covers raised)","scaleRef":"the sight's length over its cover rings, ring_span (2.856 in), is 1140 px in this photo (columns 240 to 1380): 399.2 px/in; the tube's axis is row 787 (the rings' widest rows, 775 to 800)","method":"the switch is a circle in this view: columns 715 to 1147 at its middle, rows 598 to 1030: 432 px each way","via":"harvest"}}]},"intensity_from_front":{"label":"Intensity switch's centre behind the front cover ring's end","kind":"length","measurements":[{"id":"lrp-right","value":1.125,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aimpoint-micro-t-2 6738645c90b1 (Aimpoint's own 200198_Micro_T-2_AR15_Ready_Profile_Right as Bravo Company shows it: straight right side, transparent ground, 1600 x 1600, objective to the right, both covers raised)","scaleRef":"the sight's length over its cover rings, ring_span (2.856 in), is 1140 px in this photo (columns 240 to 1380): 399.2 px/in; the tube's axis is row 787 (the rings' widest rows, 775 to 800)","method":"the circle's centre, column 931, from the front ring's end, column 1380: 449 px","via":"harvest"}}]},"intensity_below_axis":{"label":"Intensity switch's centre below the optical axis","kind":"length","measurements":[{"id":"lrp-right","value":0.068,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aimpoint-micro-t-2 6738645c90b1 (Aimpoint's own 200198_Micro_T-2_AR15_Ready_Profile_Right as Bravo Company shows it: straight right side, transparent ground, 1600 x 1600, objective to the right, both covers raised)","scaleRef":"the sight's length over its cover rings, ring_span (2.856 in), is 1140 px in this photo (columns 240 to 1380): 399.2 px/in; the tube's axis is row 787 (the rings' widest rows, 775 to 800)","method":"the circle's centre, row 814, below the axis's row 787: 27 px. Its lower edge (row 1030) hangs over the spacer's top","via":"harvest"}}]},"windage_od":{"label":"Windage adjustment cap's diameter (on the right side, behind the switch)","kind":"length","measurements":[{"id":"lrp-right","value":0.541,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aimpoint-micro-t-2 6738645c90b1 (Aimpoint's own 200198_Micro_T-2_AR15_Ready_Profile_Right as Bravo Company shows it: straight right side, transparent ground, 1600 x 1600, objective to the right, both covers raised)","scaleRef":"the sight's length over its cover rings, ring_span (2.856 in), is 1140 px in this photo (columns 240 to 1380): 399.2 px/in; the tube's axis is row 787 (the rings' widest rows, 775 to 800)","method":"the knurled cap is a circle in this view, its front edge behind the switch: columns 476 to 692, rows 700 to 916: 216 px","via":"harvest"}}]},"windage_from_front":{"label":"Windage cap's centre behind the front cover ring's end","kind":"length","measurements":[{"id":"lrp-right","value":1.994,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aimpoint-micro-t-2 6738645c90b1 (Aimpoint's own 200198_Micro_T-2_AR15_Ready_Profile_Right as Bravo Company shows it: straight right side, transparent ground, 1600 x 1600, objective to the right, both covers raised)","scaleRef":"the sight's length over its cover rings, ring_span (2.856 in), is 1140 px in this photo (columns 240 to 1380): 399.2 px/in; the tube's axis is row 787 (the rings' widest rows, 775 to 800)","method":"the cap's centre, column 584, from the front ring's end, column 1380: 796 px. The elevation turret stands over the same station (columns 515 to 668)","via":"harvest"}}]},"windage_below_axis":{"label":"Windage cap's centre below the optical axis","kind":"length","measurements":[{"id":"lrp-right","value":0.053,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aimpoint-micro-t-2 6738645c90b1 (Aimpoint's own 200198_Micro_T-2_AR15_Ready_Profile_Right as Bravo Company shows it: straight right side, transparent ground, 1600 x 1600, objective to the right, both covers raised)","scaleRef":"the sight's length over its cover rings, ring_span (2.856 in), is 1140 px in this photo (columns 240 to 1380): 399.2 px/in; the tube's axis is row 787 (the rings' widest rows, 775 to 800)","method":"the cap's centre, row 808, below the axis's row 787: 21 px","via":"harvest"}}]},"cross_bolt_from_front":{"label":"The LRP base's cross bolt (the socket in its right wall) behind the front cover ring's end","kind":"length","measurements":[{"id":"lrp-right","value":1.478,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aimpoint-micro-t-2 6738645c90b1 (Aimpoint's own 200198_Micro_T-2_AR15_Ready_Profile_Right as Bravo Company shows it: straight right side, transparent ground, 1600 x 1600, objective to the right, both covers raised)","scaleRef":"the sight's length over its cover rings, ring_span (2.856 in), is 1140 px in this photo (columns 240 to 1380): 399.2 px/in; the tube's axis is row 787 (the rings' widest rows, 775 to 800)","method":"the socket's centre, column 790, from the front ring's end, column 1380: 590 px. The base's right wall runs from column 425 to 1172: the socket is at its middle","via":"harvest"}}]},"cross_bolt_below_axis":{"label":"The LRP base's cross bolt below the optical axis","kind":"length","measurements":[{"id":"lrp-right","value":1.573,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aimpoint-micro-t-2 6738645c90b1 (Aimpoint's own 200198_Micro_T-2_AR15_Ready_Profile_Right as Bravo Company shows it: straight right side, transparent ground, 1600 x 1600, objective to the right, both covers raised)","scaleRef":"the sight's length over its cover rings, ring_span (2.856 in), is 1140 px in this photo (columns 240 to 1380): 399.2 px/in; the tube's axis is row 787 (the rings' widest rows, 775 to 800)","method":"the socket's centre, row 1415, below the axis's row 787: 628 px","via":"harvest"}}]},"cross_bolt_socket_od":{"label":"The socket's diameter in the LRP base's right wall","kind":"length","measurements":[{"id":"lrp-right","value":0.175,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aimpoint-micro-t-2 6738645c90b1 (Aimpoint's own 200198_Micro_T-2_AR15_Ready_Profile_Right as Bravo Company shows it: straight right side, transparent ground, 1600 x 1600, objective to the right, both covers raised)","scaleRef":"the sight's length over its cover rings, ring_span (2.856 in), is 1140 px in this photo (columns 240 to 1380): 399.2 px/in; the tube's axis is row 787 (the rings' widest rows, 775 to 800)","method":"the round recess with a hexagon socket in it: columns 755 to 825, 70 px","via":"harvest"}}]}}},{"subject":"aimpoint-pro","title":"Aimpoint Patrol Rifle Optic (PRO) Red Dot Reflex Sight - QRP2 Mount (12841): the sight in its 30 mm ring on the QRP2 mount with the AR-15 spacer","dimensions":{"length":{"label":"Overall length (the configuration: the sight on its mount with its lens covers, closed)","kind":"length","measurements":[{"id":"manual","value":136,"unit":"mm","stated":"Configuration 136 mm × 70 mm × 81 mm / 5.4 in × 2.8 in × 3.2 in","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, PRO user manual ([13648-4], 2013, 2021), the PDF as T.REX ARMS hosts it: 1.1 Technical specification","url":"https://img.trex-arms.com/wp/uploads/2024/09/Aimpoint-PRO-Red-Dot-Sight-Manual.pdf","retrieved":"2026-10-19","via":"harvest"}},{"id":"sheet","value":130,"unit":"mm","stated":"Length 130mm (5.1”)","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Patrol Rifle Optic (PRO) technical specifications (M01224, 2011), the PDF as Mod Armory hosts it","url":"https://www.modarmory.com/wp-content/uploads/2011/06/aimpoint-pro-patrol-rifle-optic.pdf","retrieved":"2026-10-19","via":"harvest"}},{"id":"otrade","value":130,"unit":"mm","stated":"Weight: 220 g sight only, 360 g with mount. Length: 130 mm.","source":{"type":"spec","publisher":"retailer","name":"Optics Trade, Aimpoint PRO (12841)","url":"https://www.optics-trade.eu/int/aimpoint-pro.html","retrieved":"2026-10-19","via":"harvest"}},{"id":"mhs","value":130,"unit":"mm","stated":"Length std conf: 130 mm (5 1/8\")","source":{"type":"spec","publisher":"retailer","name":"Mile High Shooting, AimPoint 12841 Patrol Rifle Optic (its long table: some rows are another sight's, a 26 mm aperture and a \"Micro spacer XX\")","url":"https://www.milehighshooting.com/aimpoint-12841-patrol-rifle-optic/","retrieved":"2026-10-19","via":"harvest"}},{"id":"city","value":5.2,"unit":"in","stated":"Size 5.2 x 2.8 x 3.2 in","source":{"type":"spec","publisher":"retailer","name":"City Arsenal, Aimpoint PRO, Patrol Rifle Optic, 2 MOA, Red Dot (12841)","url":"https://cityarsenal.com/product/aimpoint-patrol-rifle-optic-pro-red-dot-2moa-black/","retrieved":"2026-10-19","via":"harvest"}}],"adopt":{"from":"manual","reason":"The maker's newest document, and the one that says what the length is of (the configuration, beside the sight's own): the 2011 figure is the length over the raised covers' rings at this scale (ring_span), and the sellers copy one or the other."},"note":"The 2021 manual's \"Configuration\" length, beside the sight's own 122 mm: the sight with its lens covers and the mount. Primary Arms' photograph of a unit with both covers closed (references/aimpoint-pro 1c53d7be0007) is scaled by it, and at that scale the length over the two cover rings with the covers raised (ring_span, on Aimpoint's own left profile) is 130.4 mm: the 2011 sheet's \"Length 130mm\", which sellers copy, is that length, or a sight of that year; kept, not adopted."},"sight_length":{"label":"The sight's own length (no mount, no lens covers)","kind":"length","measurements":[{"id":"manual","value":122,"unit":"mm","stated":"Sight 122 mm × 49 mm × 49 mm / 4.8 in × 1.9 in × 1.9 in","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, PRO user manual ([13648-4], 2013, 2021), the PDF as T.REX ARMS hosts it: 1.1 Technical specification","url":"https://img.trex-arms.com/wp/uploads/2024/09/Aimpoint-PRO-Red-Dot-Sight-Manual.pdf","retrieved":"2026-10-19","via":"harvest"}},{"id":"sportsmans","value":4.8,"unit":"in","stated":"Length 4.8in Width 1.9in Height 1.9in Weight 7.8oz","source":{"type":"spec","publisher":"retailer","name":"Sportsman's Warehouse, Aimpoint Patrol Rifle Optic 1x Red Dot - 2 MOA Dot","url":"https://www.sportsmans.com/hunting-gear-supplies/optics-binoculars-scopes-rangefinders/red-dots/aimpoint-patrol-rifle-optic-1x-red-dot-2-moa-dot/p/1379668","retrieved":"2026-10-19","via":"harvest"}},{"id":"mhs","value":115,"unit":"mm","stated":"Length sight only: 115 mm (4 1/2\")","source":{"type":"spec","publisher":"retailer","name":"Mile High Shooting, AimPoint 12841 Patrol Rifle Optic (its long table: some rows are another sight's, a 26 mm aperture and a \"Micro spacer XX\")","url":"https://www.milehighshooting.com/aimpoint-12841-patrol-rifle-optic/","retrieved":"2026-10-19","via":"harvest"}}],"adopt":{"from":"manual","reason":"The maker's own figure; Sportsman's gives the same in inches. Mile High's table carries another sight's rows."}},"width":{"label":"Overall width (the configuration: from the torque knob's face on the left to the sight's right side)","kind":"length","measurements":[{"id":"manual","value":70,"unit":"mm","stated":"Configuration 136 mm × 70 mm × 81 mm / 5.4 in × 2.8 in × 3.2 in","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, PRO user manual ([13648-4], 2013, 2021), the PDF as T.REX ARMS hosts it: 1.1 Technical specification","url":"https://img.trex-arms.com/wp/uploads/2024/09/Aimpoint-PRO-Red-Dot-Sight-Manual.pdf","retrieved":"2026-10-19","via":"harvest"}},{"id":"city","value":2.8,"unit":"in","stated":"Size 5.2 x 2.8 x 3.2 in","source":{"type":"spec","publisher":"retailer","name":"City Arsenal, Aimpoint PRO, Patrol Rifle Optic, 2 MOA, Red Dot (12841)","url":"https://cityarsenal.com/product/aimpoint-patrol-rifle-optic-pro-red-dot-2moa-black/","retrieved":"2026-10-19","via":"harvest"}}],"adopt":{"from":"manual","reason":"The maker's figure; City Arsenal's agrees in inches."},"note":"The manual doesn't say what it spans; the torque knob on the mount's left side is the furthest thing out on the left, and the sight's own 49 mm puts its right side. The model places the knob's face by it (knob_face_z)."},"sight_width":{"label":"The sight's own width (its left flank to its right side: the battery housing and the windage cap)","kind":"length","measurements":[{"id":"manual","value":49,"unit":"mm","stated":"Sight 122 mm × 49 mm × 49 mm / 4.8 in × 1.9 in × 1.9 in","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, PRO user manual ([13648-4], 2013, 2021), the PDF as T.REX ARMS hosts it: 1.1 Technical specification","url":"https://img.trex-arms.com/wp/uploads/2024/09/Aimpoint-PRO-Red-Dot-Sight-Manual.pdf","retrieved":"2026-10-19","via":"harvest"}},{"id":"sportsmans","value":1.9,"unit":"in","stated":"Length 4.8in Width 1.9in Height 1.9in Weight 7.8oz","source":{"type":"spec","publisher":"retailer","name":"Sportsman's Warehouse, Aimpoint Patrol Rifle Optic 1x Red Dot - 2 MOA Dot","url":"https://www.sportsmans.com/hunting-gear-supplies/optics-binoculars-scopes-rangefinders/red-dots/aimpoint-patrol-rifle-optic-1x-red-dot-2-moa-dot/p/1379668","retrieved":"2026-10-19","via":"harvest"}},{"id":"mhs","value":55,"unit":"mm","stated":"Width: 55 mm (2 3/16\")","source":{"type":"spec","publisher":"retailer","name":"Mile High Shooting, AimPoint 12841 Patrol Rifle Optic (its long table: some rows are another sight's, a 26 mm aperture and a \"Micro spacer XX\")","url":"https://www.milehighshooting.com/aimpoint-12841-patrol-rifle-optic/","retrieved":"2026-10-19","via":"harvest"}}],"adopt":{"from":"manual","reason":"The maker's own figure; Sportsman's gives the same in inches."}},"height":{"label":"Overall height (the configuration)","kind":"length","measurements":[{"id":"manual","value":81,"unit":"mm","stated":"Configuration 136 mm × 70 mm × 81 mm / 5.4 in × 2.8 in × 3.2 in","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, PRO user manual ([13648-4], 2013, 2021), the PDF as T.REX ARMS hosts it: 1.1 Technical specification","url":"https://img.trex-arms.com/wp/uploads/2024/09/Aimpoint-PRO-Red-Dot-Sight-Manual.pdf","retrieved":"2026-10-19","via":"harvest"}},{"id":"city","value":3.2,"unit":"in","stated":"Size 5.2 x 2.8 x 3.2 in","source":{"type":"spec","publisher":"retailer","name":"City Arsenal, Aimpoint PRO, Patrol Rifle Optic, 2 MOA, Red Dot (12841)","url":"https://cityarsenal.com/product/aimpoint-patrol-rifle-optic-pro-red-dot-2moa-black/","retrieved":"2026-10-19","via":"harvest"}},{"id":"mhs","value":67,"unit":"mm","stated":"Height std conf: 67 mm (2 5/8\")","source":{"type":"spec","publisher":"retailer","name":"Mile High Shooting, AimPoint 12841 Patrol Rifle Optic (its long table: some rows are another sight's, a 26 mm aperture and a \"Micro spacer XX\")","url":"https://www.milehighshooting.com/aimpoint-12841-patrol-rifle-optic/","retrieved":"2026-10-19","via":"harvest"}}],"adopt":{"from":"manual","reason":"The maker's figure; City Arsenal's agrees in inches. Mile High's table carries another sight's rows."},"note":"The manual doesn't say what it spans, and no reading on the photos lands on it: at the scale the 136 mm gives, Primary Arms' photograph has 71.9 mm from the mount's lowest edge to the top of the battery housing, 74.6 mm from the clamp's jaws, and 83.1 mm from the torque knob's lowest edge. Kept as published; the model is drawn at the photos' size."},"sight_height":{"label":"The sight's own height (the main body's underside to the top of the battery housing)","kind":"length","measurements":[{"id":"manual","value":49,"unit":"mm","stated":"Sight 122 mm × 49 mm × 49 mm / 4.8 in × 1.9 in × 1.9 in","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, PRO user manual ([13648-4], 2013, 2021), the PDF as T.REX ARMS hosts it: 1.1 Technical specification","url":"https://img.trex-arms.com/wp/uploads/2024/09/Aimpoint-PRO-Red-Dot-Sight-Manual.pdf","retrieved":"2026-10-19","via":"harvest"}},{"id":"sportsmans","value":1.9,"unit":"in","stated":"Length 4.8in Width 1.9in Height 1.9in Weight 7.8oz","source":{"type":"spec","publisher":"retailer","name":"Sportsman's Warehouse, Aimpoint Patrol Rifle Optic 1x Red Dot - 2 MOA Dot","url":"https://www.sportsmans.com/hunting-gear-supplies/optics-binoculars-scopes-rangefinders/red-dots/aimpoint-patrol-rifle-optic-1x-red-dot-2-moa-dot/p/1379668","retrieved":"2026-10-19","via":"harvest"}}],"adopt":{"from":"manual","reason":"The maker's own figure; Sportsman's gives the same in inches."},"note":"Aimpoint's left profile at the scale the 136 mm gives has 48.1 mm from the main body's round underside (its radius below the axis: half the body's box in the profile) to the top of the battery housing: 2% under the maker's figure."},"optical_axis_above_rail":{"label":"Optical axis above the rail's top (with the spacer, as 12841 is sold for an AR-15)","kind":"length","measurements":[{"id":"manual","value":39,"unit":"mm","stated":"Configuration (spacer) 39 mm / 1.5 in (from top surface of Picatinny rail)","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, PRO user manual ([13648-4], 2013, 2021), the PDF as T.REX ARMS hosts it: 1.1 Technical specification","url":"https://img.trex-arms.com/wp/uploads/2024/09/Aimpoint-PRO-Red-Dot-Sight-Manual.pdf","retrieved":"2026-10-19","via":"harvest"}}],"note":"Aimpoint's 2011 sheet: the spacer \"indexes the sight at the optimal height for co-witness with the standard iron sights on Carbine style weapons\"; Primary Arms: \"Included mount provides absolute co-witness with AR-15 sights\". Where the rail's top lies inside the QRP2 isn't seen in a side view: the model's rail top is this far under the axis."},"no_spacer_axis_above_rail":{"label":"Optical axis above the rail's top without the spacer (for shotguns and submachine guns), not as this part is drawn","kind":"length","measurements":[{"id":"manual","value":30,"unit":"mm","stated":"Configuration (no spacer) 30 mm / 1.2 in (from top surface of Picatinny rail)","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, PRO user manual ([13648-4], 2013, 2021), the PDF as T.REX ARMS hosts it: 1.1 Technical specification","url":"https://img.trex-arms.com/wp/uploads/2024/09/Aimpoint-PRO-Red-Dot-Sight-Manual.pdf","retrieved":"2026-10-19","via":"harvest"}}]},"spacer_height":{"label":"The spacer's height (what it adds under the ring base)","kind":"length","measurements":[{"id":"published","value":0.3543,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.optical_axis_above_rail} - {.no_spacer_axis_above_rail}","via":"harvest"},"note":"39 mm less 30 mm: 9 mm."}],"note":"What the maker's two axis heights leave between them. On Aimpoint's left profile the band with the eight holes, from the groove under the ring base's foot to the line over the QRP2, reads 8.7 mm at the scale the 136 mm gives (rows 1044 to 1140)."},"weight":{"label":"Weight (the configuration: the sight on the QRP2 mount and the spacer, with its lens covers)","kind":"mass","measurements":[{"id":"manual","value":360,"unit":"g","stated":"Configuration 360 g / 12.7 oz","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, PRO user manual ([13648-4], 2013, 2021), the PDF as T.REX ARMS hosts it: 1.1 Technical specification","url":"https://img.trex-arms.com/wp/uploads/2024/09/Aimpoint-PRO-Red-Dot-Sight-Manual.pdf","retrieved":"2026-10-19","via":"harvest"}},{"id":"sheet","value":330,"unit":"g","stated":"Weight 330g (11.6 oz) including mount and spacer","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Patrol Rifle Optic (PRO) technical specifications (M01224, 2011), the PDF as Mod Armory hosts it","url":"https://www.modarmory.com/wp-content/uploads/2011/06/aimpoint-pro-patrol-rifle-optic.pdf","retrieved":"2026-10-19","via":"harvest"}},{"id":"pa","value":11.6,"unit":"oz","stated":"Weight 11.6 Oz","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Aimpoint PRO Patrol Rifle Optic Red Dot Sight with QRP2 Mount (12841)","url":"https://www.primaryarms.com/aimpoint-pro-patrol-rifle-optic-with-mount","retrieved":"2026-10-19","via":"harvest"}},{"id":"mhs","value":330,"unit":"g","stated":"Weight std conf: 330 g (11,6 oz) incl. Lens Covers, Mount, and Spacer","source":{"type":"spec","publisher":"retailer","name":"Mile High Shooting, AimPoint 12841 Patrol Rifle Optic (its long table: some rows are another sight's, a 26 mm aperture and a \"Micro spacer XX\")","url":"https://www.milehighshooting.com/aimpoint-12841-patrol-rifle-optic/","retrieved":"2026-10-19","via":"harvest"}},{"id":"otrade","value":360,"unit":"g","stated":"Weight: 220 g sight only, 360 g with mount. Length: 130 mm.","source":{"type":"spec","publisher":"retailer","name":"Optics Trade, Aimpoint PRO (12841)","url":"https://www.optics-trade.eu/int/aimpoint-pro.html","retrieved":"2026-10-19","via":"harvest"}}],"adopt":{"from":"manual","reason":"The maker's newest document; the 2011 figure, which two sellers copy, is kept beside it."},"note":"Two generations of the maker's figure: 330 g on the 2011 sheet (\"including mount and spacer\"), which Primary Arms and Mile High give, and 360 g in the 2021 manual, which Optics Trade gives. The 2021 sight alone is lighter than the sellers' (192 g against 220) and its configuration heavier: both kept."},"sight_weight":{"label":"Weight of the sight alone (no mount), not this part's","kind":"mass","measurements":[{"id":"manual","value":192,"unit":"g","stated":"Sight 192 g / 6.8 oz","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, PRO user manual ([13648-4], 2013, 2021), the PDF as T.REX ARMS hosts it: 1.1 Technical specification","url":"https://img.trex-arms.com/wp/uploads/2024/09/Aimpoint-PRO-Red-Dot-Sight-Manual.pdf","retrieved":"2026-10-19","via":"harvest"}},{"id":"bcm","value":220,"unit":"g","stated":"Weight 7.8 oz / 220 g (sight only)","source":{"type":"spec","publisher":"retailer","name":"Bravo Company USA, Aimpoint Patrol Rifle Optic (PRO) Red Dot Reflex Sight - QRP2 Mount (AIMPOINT-12841)","url":"https://bravocompanyusa.com/aimpoint-pro-patrol-rifle-optic/","retrieved":"2026-10-19","via":"harvest"}},{"id":"mhs","value":220,"unit":"g","stated":"Weight sight only (incl battery): 220 g (7,8 oz)","source":{"type":"spec","publisher":"retailer","name":"Mile High Shooting, AimPoint 12841 Patrol Rifle Optic (its long table: some rows are another sight's, a 26 mm aperture and a \"Micro spacer XX\")","url":"https://www.milehighshooting.com/aimpoint-12841-patrol-rifle-optic/","retrieved":"2026-10-19","via":"harvest"}},{"id":"otrade","value":220,"unit":"g","stated":"Weight: 220 g sight only, 360 g with mount. Length: 130 mm.","source":{"type":"spec","publisher":"retailer","name":"Optics Trade, Aimpoint PRO (12841)","url":"https://www.optics-trade.eu/int/aimpoint-pro.html","retrieved":"2026-10-19","via":"harvest"}},{"id":"sportsmans","value":7.8,"unit":"oz","stated":"Length 4.8in Width 1.9in Height 1.9in Weight 7.8oz","source":{"type":"spec","publisher":"retailer","name":"Sportsman's Warehouse, Aimpoint Patrol Rifle Optic 1x Red Dot - 2 MOA Dot","url":"https://www.sportsmans.com/hunting-gear-supplies/optics-binoculars-scopes-rangefinders/red-dots/aimpoint-patrol-rifle-optic-1x-red-dot-2-moa-dot/p/1379668","retrieved":"2026-10-19","via":"harvest"}}],"adopt":{"from":"manual","reason":"The maker's newest document; four sellers give 220 g, kept beside it."}},"window_d":{"label":"Clear aperture","kind":"length","measurements":[{"id":"manual","value":23,"unit":"mm","stated":"Clear aperture 23 mm / 0.9 in","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, PRO user manual ([13648-4], 2013, 2021), the PDF as T.REX ARMS hosts it: 1.1 Technical specification","url":"https://img.trex-arms.com/wp/uploads/2024/09/Aimpoint-PRO-Red-Dot-Sight-Manual.pdf","retrieved":"2026-10-19","via":"harvest"}}],"note":"Draws the lens at both ends. The sheet: \"Both the front and rear lenses are recessed within the sight body\": they are drawn at the end faces."},"tube_od":{"label":"Main tube diameter (what the ring clamps)","kind":"length","measurements":[{"id":"manual","value":30,"unit":"mm","stated":"Sight 30 mm diameter tube","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, PRO user manual ([13648-4], 2013, 2021), the PDF as T.REX ARMS hosts it: 1.1 Technical specification","url":"https://img.trex-arms.com/wp/uploads/2024/09/Aimpoint-PRO-Red-Dot-Sight-Manual.pdf","retrieved":"2026-10-19","via":"harvest"}},{"id":"sheet","value":30,"unit":"mm","stated":"Ring diameter 30mm","source":{"type":"spec","publisher":"manufacturer","name":"Aimpoint, Patrol Rifle Optic (PRO) technical specifications (M01224, 2011), the PDF as Mod Armory hosts it","url":"https://www.modarmory.com/wp-content/uploads/2011/06/aimpoint-pro-patrol-rifle-optic.pdf","retrieved":"2026-10-19","via":"harvest"}}],"adopt":{"from":"manual","reason":"The newest; the 2011 sheet gives the same."},"note":"Inside the ring in every view: it sizes the ring's bore and the tube between the ring and the main body."},"eye_relief":{"label":"Eye relief","kind":"length","measurements":[],"note":"None to state: the manual says \"Eye relief Unlimited\" and the 2011 sheet \"Eye relief Unlimited\". A red dot: the part states no eye point."},"mount_length":{"label":"The QRP2 mount's length along the rail (its body, the spacer and the ring base's foot are as long)","kind":"length","measurements":[{"id":"pa-closed","value":2.771,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aimpoint-pro 1c53d7be0007 (Primary Arms 12841_01: a photograph of a unit, straight left side on white, both covers closed)","scaleRef":"scale from aimpoint-pro.length = 5.35433 in (x-extent 1565 px → 292.3 px/in)","method":"median row width in y [0.68, 0.95] (2.761–2.771) of the traced outline (tools/trace.py); the QRP2's body under the spacer, front face to rear face, the median over its rows (the knob's block is narrower and in the middle)","via":"harvest"}},{"id":"kenzies","value":70,"unit":"mm","stated":"Length 70 mm(2.8″)","source":{"type":"spec","publisher":"retailer","name":"Kenzie's Optics, Aimpoint QRP2 Mount (12195), Specifications: the QRP2 sold alone, in the form of Aimpoint's own tables (its 30 mm axis without a spacer is the PRO manual's)","url":"https://www.kenziesoptics.com/product/aimpoint-comp-series-qrp2-mount/","retrieved":"2026-10-19","via":"harvest"},"note":"The QRP2 sold alone (12195): the same mount. 70.4 mm as read on the photograph."}],"adopt":{"from":"pa-closed","reason":"The reading every outline of the part is scaled by; the QRP2's own table (as Kenzie's Optics gives it) agrees within its last digit, which corroborates it (the detail pass, 2026-10-19)."}},"ring_span":{"label":"The sight's length over its lens covers' rings, covers raised (as the profiles have it)","kind":"length","measurements":[{"id":"left","value":5.142,"unit":"in","pm":0.039,"source":{"type":"photo","photo":"references/aimpoint-pro 15e90d27e3d6 (Aimpoint's 12841_PRO_Profile_Left as City Arsenal hosts it: straight left side, transparent ground, both covers raised)","scaleRef":"scale from aimpoint-pro.mount_length = 2.771 in (median width over 0.725–0.785 of the height from the top, 777–778 px 777 px → 280.4 px/in)","method":"width of the traced outline (tools/trace.py); the outline's length with the raised lids and their hinges cut away: the front cover ring's end to the rear one's","via":"harvest"}}]},"axis_above_knob_bottom":{"label":"Optical axis above the torque knob's lowest edge","kind":"length","measurements":[{"id":"left","value":2.28,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aimpoint-pro 15e90d27e3d6 (Aimpoint's 12841_PRO_Profile_Left as City Arsenal hosts it: straight left side, transparent ground, both covers raised)","scaleRef":"scale from aimpoint-pro.mount_length = 2.771 in (median width over 0.725–0.785 of the height from the top, 777–778 px 777 px → 280.4 px/in)","method":"centre between the top (max over 0.0 in windows) along x [2.92, 2.99] of the traced outline (tools/trace.py); the front cover ring's rounded end is round about the axis: the middle of its top and bottom edges over its last 0.07 in, above the knob's lowest edge","via":"harvest"}}]},"jaw_bottom_above_knob_bottom":{"label":"The clamp's jaws' bottom (the knob's block) above the torque knob's lowest edge","kind":"length","measurements":[{"id":"left","value":0.41,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/aimpoint-pro 15e90d27e3d6 (Aimpoint's 12841_PRO_Profile_Left as City Arsenal hosts it: straight left side, transparent ground, both covers raised)","scaleRef":"scale from aimpoint-pro.mount_length = 2.771 in (median width over 0.725–0.785 of the height from the top, 777–778 px 777 px → 280.4 px/in)","method":"y_min in x [0.53, 0.58] of the traced outline (tools/trace.py); the lowest edge of the block the knob stands in (the clamp's jaw), just ahead of the knob","via":"harvest"}}]},"rear_ring_bottom_above_knob_bottom":{"label":"The rear cover ring's underside above the torque knob's lowest edge","kind":"length","measurements":[{"id":"left","value":1.594,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aimpoint-pro 15e90d27e3d6 (Aimpoint's 12841_PRO_Profile_Left as City Arsenal hosts it: straight left side, transparent ground, both covers raised)","scaleRef":"scale from aimpoint-pro.mount_length = 2.771 in (median width over 0.725–0.785 of the height from the top, 777–778 px 777 px → 280.4 px/in)","method":"y_min in x [-2.05, -1.8] in y [0.6, 3.0] of the traced outline (tools/trace.py); the rear cover ring's underside, above the knob's lowest edge","via":"harvest"}}]},"rear_ring_od":{"label":"The rear cover ring's diameter (twice its underside below the axis): the main body's round, as drawn","kind":"length","measurements":[{"id":"derived","value":1.372,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"2 * ({.axis_above_knob_bottom} - {.rear_ring_bottom_above_knob_bottom})","via":"harvest"}}],"note":"The rear cover ring and the narrowing of the body ahead of it are turned from the outline's underside; the main body ahead of that is wider, round about the axis at the depth of its own lower edge in the profile (the body feature's box). The maker's 49 mm of sight height, from the body's underside to the top of the battery housing, reads 48.1 mm as drawn."},"knob_bottom_y":{"label":"The torque knob's lowest edge in the optic frame (y, the rail's top is 0)","kind":"length","measurements":[{"id":"derived","value":-0.7446,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.optical_axis_above_rail} - {.axis_above_knob_bottom}","via":"harvest"},"note":"Where the side profile's origin (the knob's lowest edge) sits in the part frame: the axis is the manual's 39 mm over the rail."}]},"clamp_below_rail":{"label":"How far the QRP2's jaws reach below the rail's top","kind":"length","measurements":[{"id":"derived","value":0.3346,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.axis_above_knob_bottom} - {.jaw_bottom_above_knob_bottom} - {.optical_axis_above_rail}","via":"harvest"}}],"note":"Nothing in a side view shows the rail's top inside the QRP2: it is where the manual's 39 mm puts it under the axis. Primary Arms' photograph, at its own scale, has its jaws 47.3 mm under the axis as Aimpoint's profile does (47.3 mm): the two photographs agree."},"battery_od":{"label":"The battery housing's diameter (its knurled front cap, on the right shoulder)","kind":"length","measurements":[{"id":"right","value":0.717,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/aimpoint-pro 60f4eff2e9ce (Aimpoint's 12841_PRO_Profile_Right as City Arsenal hosts it: straight right side, transparent ground, both covers raised)","scaleRef":"the mount's length, mount_length (2.771 in), is 785 px in this photo (columns 275 to 1060): 283.3 px/in","method":"the knurled front cap of the battery housing at column 760: its top edge at row 512 to its lower edge where it meets the windage cap's boss at about row 715: 203 px; read by eye on a brightened crop, hence the ±","via":"harvest"}}],"note":"Only the right profile sees the housing whole: in the left one its lower part is behind the body. Placed by the maker's sight width (its right side at 49 mm from the body's left flank) and by the left profile's top of the housing (the outline's top)."},"windage_od":{"label":"Windage cap's diameter (on the right side, under the battery housing)","kind":"length","measurements":[{"id":"right","value":0.805,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aimpoint-pro 60f4eff2e9ce (Aimpoint's 12841_PRO_Profile_Right as City Arsenal hosts it: straight right side, transparent ground, both covers raised)","scaleRef":"the mount's length, mount_length (2.771 in), is 785 px in this photo (columns 275 to 1060): 283.3 px/in","method":"the cap is a circle face on in this view: columns 372 to 600, rows 745 to 975: 228 px","via":"harvest"}}]},"windage_behind_mount_middle":{"label":"Windage cap's centre behind the mount's middle","kind":"length","measurements":[{"id":"right","value":0.639,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aimpoint-pro 60f4eff2e9ce (Aimpoint's 12841_PRO_Profile_Right as City Arsenal hosts it: straight right side, transparent ground, both covers raised)","scaleRef":"the mount's length, mount_length (2.771 in), is 785 px in this photo (columns 275 to 1060): 283.3 px/in","method":"the cap's centre, column 486, behind the mount's middle, column 667: 181 px (the left profile's elevation cap is centred 0.556 in behind the mount's middle)","via":"harvest"}}]},"windage_below_axis":{"label":"Windage cap's centre below the optical axis","kind":"length","measurements":[{"id":"right","value":0.08,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aimpoint-pro 60f4eff2e9ce (Aimpoint's 12841_PRO_Profile_Right as City Arsenal hosts it: straight right side, transparent ground, both covers raised)","scaleRef":"the mount's length, mount_length (2.771 in), is 785 px in this photo (columns 275 to 1060): 283.3 px/in","method":"the cap's centre, row 860; the axis placed from the fixed jaw's lowest edge, row 1364, by the left profile's 1.870 in between the jaws' bottom and the axis: row 837. 23 px","via":"harvest"}}]},"mount_width":{"label":"The mount's width across the rail (the QRP2, the spacer and the ring base's foot)","kind":"length","measurements":[{"id":"assumed","value":1.1,"unit":"in","pm":0.15,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view from the front, the rear or above is on file, and no page gives the mount's width. Taken as the quarter views show it, a little narrower than the main body.","via":"harvest"}}]},"qrp2_width":{"label":"The QRP2's width as sold alone (12195): its torque knob's face to the outer face of its fixed (right) jaw","kind":"length","measurements":[{"id":"kenzies","value":55,"unit":"mm","stated":"Width 55 mm(2.2″)","source":{"type":"spec","publisher":"retailer","name":"Kenzie's Optics, Aimpoint QRP2 Mount (12195), Specifications: the QRP2 sold alone, in the form of Aimpoint's own tables (its 30 mm axis without a spacer is the PRO manual's)","url":"https://www.kenziesoptics.com/product/aimpoint-comp-series-qrp2-mount/","retrieved":"2026-10-19","via":"harvest"}}],"note":"A mount's \"Width\" whose torque knob stands out of its left side: taken to span the knob's face to the far jaw, as the configuration's 70 mm spans the knob's face to the sight's right side (the furthest things out each side, the same knob in both). Kenzie's Optics gives it in Aimpoint's form; aimpoint.com, where the table is from, refuses the reader. With the drawing's knob face (knob_face_z, by the 70 mm) the model's QRP2 was 54.0 mm across (2026-10-19, before the detail pass)."},"qrp2_right_inboard":{"label":"How far the QRP2's right (fixed) jaw's outer face stands inboard of the sight's right side","kind":"length","measurements":[{"id":"derived","value":0.5906,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.width} - {.qrp2_width}","via":"harvest"},"note":"70 mm less 55 mm. The ± is the two figures' last digits."}],"note":"What Aimpoint's two widths leave between them, the configuration's 70 mm (the knob's face to the sight's right side) less the QRP2's 55 mm (the knob's face to its right jaw), the same knob face at one end of both: 15 mm. The model's QRP2 right face is that far in from the sight's right side, which the maker's 49 mm of sight width places (right_z in the manifest): 0.59 in from the rail's middle, where the assumed mount_width had 0.55. Primary Arms' photograph from ahead and to the right (e97955bbce77) shows the QRP2's top as a strip beyond the spacer's right face (the QRP2 the wider), as this has it; a camera fitted to that photo didn't settle (see the part's gaps), so the photo isn't the reading."},"right_jaw_below_holes":{"label":"The QRP2's right jaw's lowest edge below the middle of the spacer's row of holes","kind":"length","measurements":[{"id":"right","value":0.729,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/aimpoint-pro 60f4eff2e9ce (Aimpoint's 12841_PRO_Profile_Right as City Arsenal hosts it: straight right side, transparent ground, both covers raised)","scaleRef":"the mount's length, mount_length (2.771 in), is 785 px in this photo (columns 275 to 1060): 283.3 px/in","method":"the holes' row: each hole from row 1133-1134 (its top rim) to 1178-1179 (its bottom), their middle row 1156.0 (the eight agree to a pixel); the mount's lowest edge, the alpha silhouette's last opaque row at every 20th column from 280 to 1040: 1360 to 1364, level within 3 px, median 1362.5: 206.5 px. The ± covers 2 px each end and the scale.","via":"harvest"}}],"note":"Read on the one straight view of the right side, where the jaw and the holes are on the near side together (Aimpoint's profiles look taken from a little above: each near face is read against its own near face). The left profile's strip under the left wall (the trace's lip, 0.558 in under its holes) is the far, right jaw's lower edge seen from about 9 degrees above (0.729 less 0.558 over the 1.05 in across the mount), not a lip of the left wall: the front end face in Primary Arms' photograph from ahead and to the right (e97955bbce77) has the left side end at the channel's roof with no lip under it, and Optics Trade's photograph of the QRP2 alone from its channel side (1dbb191bfb52) has the left side's edge plain along both ends, a hook only on the movable jaw at its middle. The movable jaw (the knob's block) reaches 0.740 in under its holes in the left profile (rows 1091.5 to 1299 at 280.4 px/in), as traced (the jaw feature)."},"ring_ear_reach":{"label":"How far the ring's flats (where its two screws go down) stand out past its round","kind":"length","measurements":[{"id":"assumed","value":0.24,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the quarter views show the top ring's two flats beside its round, a little more than a screw head wide (the heads read 0.21 in across in the left profile, the ring_screws feature); no view along the sight is on file.","via":"harvest"}}]},"lid_thickness":{"label":"The lens covers' lids' thickness","kind":"length","measurements":[{"id":"assumed","value":0.12,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: both lids are seen at a slant in the side views, so their thickness isn't read.","via":"harvest"}}]},"rotary_switch_length":{"label":"The rotary switch's knurled ring at the battery housing's rear end, its length along the sight","kind":"length","measurements":[{"id":"right","value":0.494,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aimpoint-pro 60f4eff2e9ce (Aimpoint's 12841_PRO_Profile_Right as City Arsenal hosts it: straight right side, transparent ground, both covers raised)","scaleRef":"the mount's length, mount_length (2.771 in), is 785 px in this photo (columns 275 to 1060): 283.3 px/in","method":"the knurled ring with its set screw at the housing's rear end, columns 120 to 260: 140 px (in the left profile it is behind the rear lid's hinge)","via":"harvest"}}]}}},{"subject":"armaspec-stealth-recoil-spring-gen4-c","title":"Armaspec Stealth Recoil Spring SRS GEN4, C","dimensions":{"length":{"label":"Length (the weight's front face to the bumper's rear face)","kind":"length","measurements":[{"id":"family","value":7.18,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{armaspec-stealth-recoil-spring-gen4-h.length}","via":"harvest"},"note":"The maker gives one length for every version."},{"id":"mgw","value":7.18,"unit":"in","pm":0.005,"stated":"SRS-C 7.18\" 3.3 oz. 6.2 oz.","source":{"type":"spec","publisher":"retailer","name":"Midwest Gun Works, Armaspec Gen 4 Stealth Recoil Spring, SRS-Kit (Code: ARM253-AR15KIT): its table's SRS-C row","url":"https://www.midwestgunworks.com/page/mgwi/prod/arm253-ar15kit","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"family","reason":"The maker's one figure; the seller's row for the C agrees."}},"weight":{"label":"Weight (the complete system, the C)","kind":"mass","measurements":[{"id":"maker","value":6.2,"unit":"oz","pm":0.05,"stated":"Actual Wight - Complete System (new version with stainless steel weight): C: 6.2 oz.","source":{"type":"spec","publisher":"manufacturer","name":"Armaspec, Stealth™ Recoil Spring - SRS™- AR15 GEN4 (the maker's page)","url":"https://armaspec.com/stealthtm-recoil-spring-srstm-ar15-1.html","retrieved":"2026-10-18","via":"harvest"}},{"id":"redcon1","value":6.15,"unit":"oz","pm":0.005,"stated":"Weight: 6.15 oz (assembly)","source":{"type":"spec","publisher":"retailer","name":"Redcon1 Tactical, Armaspec AR-15 Stealth Recoil Spring (SRS) Carbine GEN4 (C) - 3.3 oz (Mnf# ARM253-C)","url":"https://redcon1tactical.com/armaspec-ar-15-stealth-recoil-spring-srs-carbine-gen4-c-3-3-oz.html","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"maker","reason":"The maker's figure for the Gen 4's stainless weight; the seller's 6.15 is inside its last digit's half and a twentieth of an ounce under it, of which unit isn't said."}},"equivalent_weight":{"label":"The buffer weight it stands for (the maker's \"equivalent\")","kind":"mass","measurements":[{"id":"maker","value":3.3,"unit":"oz","pm":0.05,"stated":"Equivalent Weight: C: 3.3 oz.","source":{"type":"spec","publisher":"manufacturer","name":"Armaspec, Stealth™ Recoil Spring - SRS™- AR15 GEN4 (the maker's page)","url":"https://armaspec.com/stealthtm-recoil-spring-srstm-ar15-1.html","retrieved":"2026-10-18","via":"harvest"}}]},"od":{"label":"The weight's diameter (it runs in the extension's bore)","kind":"length","measurements":[{"id":"family","value":0.946,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{armaspec-stealth-recoil-spring-gen4-h.od}","via":"harvest"},"note":"The lineup has the C's front 127 to 130 px across, as the others'."}]},"weight_length":{"label":"The C's weight, its length (neck and all)","kind":"length","measurements":[{"id":"lineup","value":1.278,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/armaspec-stealth-recoil-spring-gen4 190973a6b58c (the maker's lineup, the C at the top)","scaleRef":"the unit's own length end to end, 983 px for 7.18 in","method":"from its neck's rear face (808 px from the unit's rear end) to its front (983)","via":"harvest"}}]},"neck_d":{"label":"The C's weight, its neck's diameter","kind":"length","measurements":[{"id":"lineup","value":0.774,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/armaspec-stealth-recoil-spring-gen4 190973a6b58c (the maker's lineup, the C)","scaleRef":"the unit's own length end to end, 983 px for 7.18 in","method":"106 px across, steady from 816 to 870 px","via":"harvest"}}]},"neck_length":{"label":"The C's weight, its neck's straight run","kind":"length","measurements":[{"id":"lineup","value":0.475,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/armaspec-stealth-recoil-spring-gen4 190973a6b58c (the maker's lineup, the C)","scaleRef":"the unit's own length end to end, 983 px for 7.18 in","method":"808 to 873 px from the unit's rear end","via":"harvest"}}]},"neck_taper":{"label":"The C's weight, the taper from its neck out to its full diameter","kind":"length","measurements":[{"id":"lineup","value":0.168,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/armaspec-stealth-recoil-spring-gen4 190973a6b58c (the maker's lineup, the C)","scaleRef":"the unit's own length end to end, 983 px for 7.18 in","method":"873 to 896 px, 106 px across rising to 130; 7b6e26a86e96 (the maker's side view of the C) shows it as one straight cone","via":"harvest"}}]}}},{"subject":"armaspec-stealth-recoil-spring-gen4-h","title":"Armaspec Stealth Recoil Spring SRS GEN4, H","dimensions":{"length":{"label":"Length (the weight's front face to the bumper's rear face)","kind":"length","measurements":[{"id":"maker","value":7.18,"unit":"in","pm":0.005,"stated":"Length: 7.18\"","source":{"type":"spec","publisher":"manufacturer","name":"Armaspec, Stealth™ Recoil Spring - SRS™- AR15 GEN4 (the maker's page: one length for every version)","url":"https://armaspec.com/stealthtm-recoil-spring-srstm-ar15-1.html","retrieved":"2026-10-18","via":"harvest"}},{"id":"primary-arms","value":7.18,"unit":"in","pm":0.005,"stated":"7.18\" Length","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Armaspec Stealth AR-15 Recoil Spring - H 3.8 oz - Gen 4 (SKU: ARM253-H)","url":"https://www.primaryarms.com/armaspec-stealth-ar-15-recoil-spring-h-3-8-oz-gen-4","retrieved":"2026-10-18","via":"harvest"}},{"id":"mgw","value":7.18,"unit":"in","pm":0.005,"stated":"SRS-H 7.18\" 3.8 oz. 6.6 oz.","source":{"type":"spec","publisher":"retailer","name":"Midwest Gun Works, Armaspec Gen 4 Stealth Recoil Spring, SRS-Kit (Code: ARM253-AR15KIT): its table's SRS-H row","url":"https://www.midwestgunworks.com/page/mgwi/prod/arm253-ar15kit","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"maker","reason":"The maker's figure; two sellers repeat it. The maker's lineup photo has all four weights at one length end to end (983, 983, 984 and 981 px)."}},"weight":{"label":"Weight (the complete system, the H)","kind":"mass","measurements":[{"id":"maker","value":6.6,"unit":"oz","pm":0.05,"stated":"Actual Wight - Complete System (new version with stainless steel weight): C: 6.2 oz. H: 6.6 oz.","source":{"type":"spec","publisher":"manufacturer","name":"Armaspec, Stealth™ Recoil Spring - SRS™- AR15 GEN4 (the maker's page)","url":"https://armaspec.com/stealthtm-recoil-spring-srstm-ar15-1.html","retrieved":"2026-10-18","via":"harvest"}},{"id":"primary-arms","value":6.6,"unit":"oz","pm":0.05,"stated":"Actual weight of complete system: 6.6 oz","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Armaspec Stealth AR-15 Recoil Spring - H 3.8 oz - Gen 4 (SKU: ARM253-H)","url":"https://www.primaryarms.com/armaspec-stealth-ar-15-recoil-spring-h-3-8-oz-gen-4","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"maker","reason":"The maker's figure; the seller repeats it."}},"equivalent_weight":{"label":"The buffer weight it stands for (the maker's \"equivalent\")","kind":"mass","measurements":[{"id":"maker","value":3.8,"unit":"oz","pm":0.05,"stated":"Equivalent Weight: C: 3.3 oz. H: 3.8 oz. H2: 4.7 oz. H3: 5.6 oz.","source":{"type":"spec","publisher":"manufacturer","name":"Armaspec, Stealth™ Recoil Spring - SRS™- AR15 GEN4 (the maker's page)","url":"https://armaspec.com/stealthtm-recoil-spring-srstm-ar15-1.html","retrieved":"2026-10-18","via":"harvest"}}],"note":"Not what it weighs: the standard buffer it is sold to take the place of, by weight class. The complete system is `weight`."},"od":{"label":"The weight's diameter (it runs in the extension's bore)","kind":"length","measurements":[{"id":"lineup","value":0.946,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/armaspec-stealth-recoil-spring-gen4 190973a6b58c (the maker's lineup, 1161 px: the H second from the top)","scaleRef":"the unit's own length end to end, 983 px for the maker's 7.18 in","method":"the weight's silhouette, 129 to 130 px across along its length (the H's, the H2's and the H3's alike); the ± covers the camera's 1% and the edge","via":"harvest"}}]},"bumper_d":{"label":"The bumper's diameter","kind":"length","measurements":[{"id":"lineup","value":0.957,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/armaspec-stealth-recoil-spring-gen4 190973a6b58c (the maker's lineup)","scaleRef":"the unit's own length end to end, 983 px for 7.18 in","method":"the bumper's silhouette, 130 to 131 px across in all four units","via":"harvest"},"note":"A hundredth more than the weight's in the one photo that sees both from square across; inside the extension's inch."}]},"bumper_length":{"label":"The bumper's length (the C's, the H's and the H2's)","kind":"length","measurements":[{"id":"lineup","value":1.395,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/armaspec-stealth-recoil-spring-gen4 190973a6b58c (the maker's lineup)","scaleRef":"the unit's own length end to end, 983 px for 7.18 in","method":"from the unit's rear end to where the silhouette falls from the bumper's 131 px to the spring's (191 px), the same in the top three units","via":"harvest"}}]},"rod_end_d":{"label":"The rod's end in the bumper's rear face","kind":"length","measurements":[{"id":"face","value":0.33,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/armaspec-stealth-recoil-spring-gen4 43bd2dd80751 (Primary Arms' ARM253-H_02: the bumper's rear face seen at an angle, PAT. USD864337 and PAT. US8800424 engraved on it)","scaleRef":"the face's own diameter (bumper_d), in its plane","method":"the steel disc's width across the face's ellipse along its long axis, 0.34 of the face's","via":"harvest"}}]},"bumper_slot_w":{"label":"The slot across the bumper's rear face (the roll pin lies in it)","kind":"length","measurements":[{"id":"face","value":0.048,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/armaspec-stealth-recoil-spring-gen4 43bd2dd80751 (Primary Arms' ARM253-H_02, the bumper's rear face)","scaleRef":"the face's own diameter (bumper_d), in its plane","method":"the slot's width square to its length, a twentieth of the face's","via":"harvest"}}],"note":"The maker's page: \"we changed the screw to a roll pin across the plastic end piece\"."},"bumper_slot_depth":{"label":"The slot's depth in the bumper's rear face, to the pin","kind":"length","measurements":[{"id":"assumed","value":0.1,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows the slot in profile; the pin is seen at its floor.","via":"harvest"}}]},"rod_end_length":{"label":"How far the rod's end runs into the bumper at its larger size","kind":"length","measurements":[{"id":"assumed","value":0.3,"unit":"in","pm":0.15,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the rod's end is seen only in the bumper's rear face.","via":"harvest"}}]},"rod_d":{"label":"The rod's diameter under the main spring","kind":"length","measurements":[{"id":"photo","value":0.176,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/armaspec-stealth-recoil-spring-gen4 954e1211557e (the maker's arm253-h_3_1.jpg, 1800 px, near side-on)","scaleRef":"the weight's own diameter (od) in the same photo, 204 px","method":"the narrowest dark run through the axis between the coils, 35 to 41 px, behind the bumper's front face","via":"harvest"}}]},"sleeve_d":{"label":"The rod's diameter under the second spring (washer to weight)","kind":"length","measurements":[{"id":"photo","value":0.39,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/armaspec-stealth-recoil-spring-gen4 954e1211557e (the maker's arm253-h_3_1.jpg)","scaleRef":"the weight's own diameter (od) in the same photo, 204 px","method":"the dark run through the axis between the second spring's coils, 82 to 87 px","via":"harvest"}}]},"washer_od":{"label":"The washer between the two springs, its diameter","kind":"length","measurements":[{"id":"lineup","value":0.709,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/armaspec-stealth-recoil-spring-gen4 190973a6b58c (the maker's lineup)","scaleRef":"the unit's own length end to end, 983 px for 7.18 in","method":"97 px across, in all four units","via":"harvest"}}]},"washer_length":{"label":"The washer's length along the rod","kind":"length","measurements":[{"id":"lineup","value":0.212,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/armaspec-stealth-recoil-spring-gen4 190973a6b58c (the maker's lineup)","scaleRef":"the unit's own length end to end, 983 px for 7.18 in","method":"its run at 97 px across, from 575 to 604 px from the unit's rear end (the H3's 528 to 560)","via":"harvest"}}]},"washer_front_x":{"label":"Where the washer's front face stands, behind the weight's front face (the C, the H and the H2)","kind":"length","measurements":[{"id":"lineup","value":2.768,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/armaspec-stealth-recoil-spring-gen4 190973a6b58c (the maker's lineup)","scaleRef":"the unit's own length end to end, 983 px for 7.18 in","method":"604 px from the unit's rear end in the top three units: 379 px from the front","via":"harvest"}}]},"main_spring_od":{"label":"The main spring's outside diameter","kind":"length","measurements":[{"id":"lineup","value":0.394,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/armaspec-stealth-recoil-spring-gen4 190973a6b58c (the maker's lineup)","scaleRef":"the unit's own length end to end, 983 px for 7.18 in","method":"the envelope of the coils' crests, 54 px","via":"harvest"}}]},"main_wire_d":{"label":"The main spring's wire","kind":"length","measurements":[{"id":"photo","value":0.034,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/armaspec-stealth-recoil-spring-gen4 954e1211557e (the maker's arm253-h_3_1.jpg)","scaleRef":"the weight's own diameter (od) in the same photo, 204 px","method":"a coil's wire square across its run where it crosses the rod, 7 px","via":"harvest"}}]},"main_coils":{"label":"The main spring's coils","kind":"count","measurements":[{"id":"photo","value":25,"unit":"count","pm":1,"source":{"type":"photo","photo":"references/armaspec-stealth-recoil-spring-gen4 954e1211557e (the H), 7b6e26a86e96 (the C), 228008b8823f (the H2), 5a44c78c3155 (the H3)","scaleRef":"none: a count","method":"counted along the top of the silhouette on the H's photo, bumper to washer (25, the last against the washer); the pitch by the brightness's autocorrelation along it, 22.8 to 24.9 px in the four photos, gives 24 to 27 over the run","via":"harvest"}}]},"second_spring_od":{"label":"The second (front) spring's outside diameter","kind":"length","measurements":[{"id":"lineup","value":0.65,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/armaspec-stealth-recoil-spring-gen4 190973a6b58c (the maker's lineup)","scaleRef":"the unit's own length end to end, 983 px for 7.18 in","method":"the envelope of the coils' crests, 89 px","via":"harvest"}}]},"second_wire_d":{"label":"The second spring's wire","kind":"length","measurements":[{"id":"photo","value":0.045,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/armaspec-stealth-recoil-spring-gen4 954e1211557e and 7b6e26a86e96 (the maker's H and C side views)","scaleRef":"the weight's own diameter (od) in the same photo","method":"a coil's wire square across its run, 9 to 11 px","via":"harvest"}}]},"second_coils":{"label":"The second spring's coils","kind":"count","measurements":[{"id":"photo","value":10,"unit":"count","pm":1,"source":{"type":"photo","photo":"references/armaspec-stealth-recoil-spring-gen4 954e1211557e (the H) and 7b6e26a86e96 (the C)","scaleRef":"none: a count","method":"the wire's crossings along the top of the silhouette, washer to weight: two closed at the washer, six open, two closed at the weight, in both","via":"harvest"}}]},"counterbore_d":{"label":"The bore in the weight's front face (the rod's cap is at its floor)","kind":"length","measurements":[{"id":"photo","value":0.61,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/armaspec-stealth-recoil-spring-gen4 d298ab5258d9 (Primary Arms' ARM253-H_01: the weight's front face seen at an angle)","scaleRef":"the face's own diameter (od), in its plane","method":"the bore's ellipse over the face's, 0.653 along the long axis and 0.633 along the short","via":"harvest"}}]},"cap_depth":{"label":"How deep in the weight's front bore the rod's cap stands (free, out of the rifle)","kind":"length","measurements":[{"id":"assumed","value":0.3,"unit":"in","pm":0.15,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the cap is seen at the bore's floor in Primary Arms' oblique photo, and no view gives the depth.","via":"harvest"}}]},"cap_d":{"label":"The rod's cap (\"the cap is machined on the rod\")","kind":"length","measurements":[{"id":"assumed","value":0.5,"unit":"in","pm":0.08,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: it holds the weight on the rod, so it is wider than the rod under the weight and narrower than the bore it sits in.","via":"harvest"}}]},"cap_t":{"label":"The cap's thickness","kind":"length","measurements":[{"id":"assumed","value":0.08,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading.","via":"harvest"}}]},"edge_break":{"label":"The edges' break on the weight, the washer and the bumper","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the edges read rounded at the photos' size, by a pixel or two.","via":"harvest"}}]},"weight_length":{"label":"The H's weight, its length","kind":"length","measurements":[{"id":"lineup","value":1.264,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/armaspec-stealth-recoil-spring-gen4 190973a6b58c (the maker's lineup, the H second from the top)","scaleRef":"the unit's own length end to end, 983 px for 7.18 in","method":"from its rear face (810 px from the unit's rear end) to its front (983)","via":"harvest"}}]},"pocket_d":{"label":"The pocket in the weight's rear face that the second spring's end goes into","kind":"length","measurements":[{"id":"assumed","value":0.68,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: wider than the spring it takes (second_spring_od, 0.65) and inside the weight's 0.946; no view sees into it.","via":"harvest"}}],"note":"Seen in every side view: the second spring's last coil goes in behind the weight's rear rim (954e1211557e, the H), and the H2's and the H3's weights hide several coils of it (228008b8823f, 5a44c78c3155)."},"rod_hole_d":{"label":"The cross hole in the rod ahead of the washer (for a hex key, as a lever)","kind":"length","measurements":[{"id":"key","value":0.11,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"A 3/32 in hex key goes through it (Redcon1's sentence, https://redcon1tactical.com/armaspec-ar-15-stealth-recoil-spring-srs-carbine-gen4-c-3-3-oz.html): drawn at the key's size across its corners, 0.094 / cos 30°. Not a reading of the hole.","via":"harvest"}}],"note":"Redcon1's installation text: \"re-tighten the screws using either using two 3/32 hex keys and fully tightening both screws at the same time or using one 3/32 hex key and using the hole in the rod for leverage.\" Seen in the maker's side view of the H2 (228008b8823f) at the thick rod's lower edge, just ahead of the washer, partly under the spring's first coil."},"rod_hole_ahead":{"label":"How far ahead of the washer's front face the rod's cross hole's middle is","kind":"length","measurements":[{"id":"photo","value":0.06,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/armaspec-stealth-recoil-spring-gen4 228008b8823f (the maker's arm253-h2_3_1.jpg, 1800 px)","scaleRef":"the unit's own length end to end, 1500 px for 7.18 in","method":"the hole's visible part 7 to 12 px ahead of the washer's front face, under the first coil; the ± covers what the coil hides","via":"harvest"}}]}}},{"subject":"armaspec-stealth-recoil-spring-gen4-h2","title":"Armaspec Stealth Recoil Spring SRS GEN4, H2","dimensions":{"length":{"label":"Length (the weight's front face to the bumper's rear face)","kind":"length","measurements":[{"id":"family","value":7.18,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{armaspec-stealth-recoil-spring-gen4-h.length}","via":"harvest"},"note":"The maker gives one length for every version."},{"id":"primary-arms","value":7.18,"unit":"in","pm":0.005,"stated":"7.18\" Length","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Armaspec Stealth AR-15 Recoil Spring - H2 4.7 oz - Gen 4 (SKU: ARM253-H2)","url":"https://www.primaryarms.com/armaspec-stealth-ar-15-recoil-spring-h2-4-7-oz-gen-4","retrieved":"2026-10-18","via":"harvest"}},{"id":"mgw","value":7.68,"unit":"in","pm":0.005,"stated":"SRS-H2 7.68\" 4.7 oz. 7.4 oz.","source":{"type":"spec","publisher":"retailer","name":"Midwest Gun Works, Armaspec Gen 4 Stealth Recoil Spring, SRS-Kit (Code: ARM253-AR15KIT): its table's SRS-H2 row","url":"https://www.midwestgunworks.com/page/mgwi/prod/arm253-ar15kit","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"family","reason":"The maker gives 7.18 for every version, Primary Arms 7.18 for the H2, and the maker's lineup photo has the H2 the same length end to end as the C and the H (984 px against 983). One seller's table row half an inch longer, beside its own 7.18 for the other two rows, is kept and not drawn: 7.68 in wouldn't go in the 7.23 in a carbine extension leaves it."}},"weight":{"label":"Weight (the complete system, the H2)","kind":"mass","measurements":[{"id":"maker","value":7.4,"unit":"oz","pm":0.05,"stated":"Actual Wight - Complete System (new version with stainless steel weight): C: 6.2 oz. H: 6.6 oz. H2: 7.4 oz.","source":{"type":"spec","publisher":"manufacturer","name":"Armaspec, Stealth™ Recoil Spring - SRS™- AR15 GEN4 (the maker's page)","url":"https://armaspec.com/stealthtm-recoil-spring-srstm-ar15-1.html","retrieved":"2026-10-18","via":"harvest"}},{"id":"primary-arms","value":7.4,"unit":"oz","pm":0.05,"stated":"Actual weight of complete system: 7.4 oz","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Armaspec Stealth AR-15 Recoil Spring - H2 4.7 oz - Gen 4 (SKU: ARM253-H2)","url":"https://www.primaryarms.com/armaspec-stealth-ar-15-recoil-spring-h2-4-7-oz-gen-4","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"maker","reason":"The maker's figure; the seller repeats it."}},"equivalent_weight":{"label":"The buffer weight it stands for (the maker's \"equivalent\")","kind":"mass","measurements":[{"id":"maker","value":4.7,"unit":"oz","pm":0.05,"stated":"Equivalent Weight: C: 3.3 oz. H: 3.8 oz. H2: 4.7 oz.","source":{"type":"spec","publisher":"manufacturer","name":"Armaspec, Stealth™ Recoil Spring - SRS™- AR15 GEN4 (the maker's page)","url":"https://armaspec.com/stealthtm-recoil-spring-srstm-ar15-1.html","retrieved":"2026-10-18","via":"harvest"}}]},"od":{"label":"The weight's diameter (it runs in the extension's bore)","kind":"length","measurements":[{"id":"family","value":0.946,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{armaspec-stealth-recoil-spring-gen4-h.od}","via":"harvest"}}]},"weight_length":{"label":"The H2's weight, its length","kind":"length","measurements":[{"id":"lineup","value":1.753,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/armaspec-stealth-recoil-spring-gen4 190973a6b58c (the maker's lineup, the H2 third from the top)","scaleRef":"the unit's own length end to end, 984 px for 7.18 in","method":"from its rear face (744 px from the unit's rear end) to its front (984)","via":"harvest"}}]},"spring_pocket_depth":{"label":"How deep the second spring goes into the pocket in the H2's weight's rear face","kind":"length","measurements":[{"id":"photo","value":0.489,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{.weight_length} - {armaspec-stealth-recoil-spring-gen4-h.weight_length}","via":"harvest"},"note":"The second spring stands at the same pitch in the maker's side views of the H and the H2 (its open coils 40.5 px apart in both, 954e1211557e and 228008b8823f, taken at one scale: 1491 and 1500 px end to end), so it is the same length in both; with the washer in one place (the lineup), the H2's longer weight holds that much of it inside. Its visible coils agree: five and a half of the H's ten."}]}}},{"subject":"armaspec-stealth-recoil-spring-gen4-h3","title":"Armaspec Stealth Recoil Spring SRS GEN4, H3","dimensions":{"length":{"label":"Length (the weight's front face to the bumper's rear face)","kind":"length","measurements":[{"id":"family","value":7.18,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{armaspec-stealth-recoil-spring-gen4-h.length}","via":"harvest"},"note":"The maker gives one length for every version; its lineup has the H3 981 px end to end against the others' 983."}]},"weight":{"label":"Weight (the complete system, the H3)","kind":"mass","measurements":[{"id":"maker","value":8,"unit":"oz","pm":0.05,"stated":"Actual Wight - Complete System (new version with stainless steel weight): C: 6.2 oz. H: 6.6 oz. H2: 7.4 oz. H3: 8.0 oz.","source":{"type":"spec","publisher":"manufacturer","name":"Armaspec, Stealth™ Recoil Spring - SRS™- AR15 GEN4 (the maker's page)","url":"https://armaspec.com/stealthtm-recoil-spring-srstm-ar15-1.html","retrieved":"2026-10-18","via":"harvest"}}]},"equivalent_weight":{"label":"The buffer weight it stands for (the maker's \"equivalent\")","kind":"mass","measurements":[{"id":"maker","value":5.6,"unit":"oz","pm":0.05,"stated":"Equivalent Weight: C: 3.3 oz. H: 3.8 oz. H2: 4.7 oz. H3: 5.6 oz.","source":{"type":"spec","publisher":"manufacturer","name":"Armaspec, Stealth™ Recoil Spring - SRS™- AR15 GEN4 (the maker's page)","url":"https://armaspec.com/stealthtm-recoil-spring-srstm-ar15-1.html","retrieved":"2026-10-18","via":"harvest"}}]},"od":{"label":"The weight's diameter (it runs in the extension's bore)","kind":"length","measurements":[{"id":"family","value":0.946,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{armaspec-stealth-recoil-spring-gen4-h.od}","via":"harvest"}}]},"weight_length":{"label":"The H3's weight, its length","kind":"length","measurements":[{"id":"lineup","value":1.962,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/armaspec-stealth-recoil-spring-gen4 190973a6b58c (the maker's lineup, the H3 at the bottom)","scaleRef":"the unit's own length end to end, 981 px for 7.18 in (136.6 px/in)","method":"from its rear face (713 px from the unit's rear end) to its front (981)","via":"harvest"}}]},"bumper_length":{"label":"The H3's bumper, its length","kind":"length","measurements":[{"id":"lineup","value":0.761,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/armaspec-stealth-recoil-spring-gen4 190973a6b58c (the maker's lineup, the H3); 5a44c78c3155 (the maker's side view of the H3/BB) shows the same short bumper","scaleRef":"the unit's own length end to end, 981 px for 7.18 in","method":"from the unit's rear end to where the silhouette falls from 131 px to the spring's (104 px)","via":"harvest"}}]},"washer_front_x":{"label":"Where the H3's washer's front face stands, behind the weight's front face","kind":"length","measurements":[{"id":"lineup","value":3.082,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/armaspec-stealth-recoil-spring-gen4 190973a6b58c (the maker's lineup, the H3)","scaleRef":"the unit's own length end to end, 981 px for 7.18 in","method":"560 px from the unit's rear end: 421 px from the front","via":"harvest"}}]},"spring_pocket_depth":{"label":"How deep the second spring goes into the pocket in the H3's weight's rear face","kind":"length","measurements":[{"id":"photo","value":0.18,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/armaspec-stealth-recoil-spring-gen4 5a44c78c3155 (the maker's side view of the H3/BB, 1482 px end to end) beside 954e1211557e (the H's, 1491 px: one scale within 0.6%)","scaleRef":"the H's second spring's length (armaspec-stealth-recoil-spring-gen4-h.washer_front_x less its weight_length, 1.504 in) and the ratio of the two photos' coil pitches","method":"the H3's open coils stand 35 px apart against the H's 40.5, so its spring is held at 0.86 of the H's length, 1.30 in; the lineup shows 1.12 in of it between the washer and the weight; the rest, 0.18 in, is in the pocket. About eight of the ten coils show, which agrees","via":"harvest"},"note":"Not the H2's reasoning (the same pitch, the same length): the H3's spring is held shorter, its washer further back."}]},"main_coils":{"label":"The H3's main spring's coils (its run is longer than the others')","kind":"count","measurements":[{"id":"photo","value":27,"unit":"count","pm":1.5,"source":{"type":"photo","photo":"references/armaspec-stealth-recoil-spring-gen4 190973a6b58c (the maker's lineup, the H3) and 5a44c78c3155 (the maker's side view of the H3/BB)","scaleRef":"none: a count","method":"the run from the bumper to the washer over the coils' pitch by the brightness's autocorrelation along it: 424 px over 15.0 px, 28.2, in the lineup (the others' 381 over 16.9, 22.6, against the 25 counted on the H's own photo), and 26.3 in its side view; the H's 25 doesn't fill the H3's longer run at the H's pitch","via":"harvest"}}]}}},{"subject":"asm.v1","title":"Build v1 assembly results","dimensions":{"oal_pos1":{"label":"Overall length, stock position 1","kind":"length","measurements":[{"id":"brief","value":30.5,"unit":"in","source":{"type":"derived","basis":"Stated in the brief as the result of the photo measurements (butt position and 22RB muzzle); the intermediate muzzle position was not recorded.","via":"brief"}}]},"oal_pos6":{"label":"Overall length, stock position 6","kind":"length","measurements":[{"id":"brief","value":33.8,"unit":"in","source":{"type":"derived","expr":"{.oal_pos1} + 5 * {magpul-moe-sl-carbine.position_step}","via":"brief"}}]}}},{"subject":"b5-bravo-stock","title":"B5 Systems Bravo Stock","dimensions":{"length":{"label":"Overall length","kind":"length","measurements":[{"id":"b5","value":7.2,"unit":"in","stated":"Length: 7.2 in","source":{"type":"spec","publisher":"manufacturer","name":"B5 Systems, BRAVO STOCK (the page's 'specs' list)","url":"https://b5systems.com/collection/ar/bravo-stock/","retrieved":"2026-10-05","via":"harvest"}},{"id":"wing","value":7.2,"unit":"in","stated":"Length: 7.2\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, B5 Systems Bravo Stock (MPN: BRV-1082 / BRV-1085 / BRV-1104)","url":"https://www.wingtactical.com/firearm-parts-accessories/ar-15-parts/ar-stocks-and-accessories/b5-systems-bravo-stock/","retrieved":"2026-10-05","via":"harvest"}},{"id":"trex","value":7.2,"unit":"in","stated":"Length 7.2 in.","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, B5 Systems BRAVO Stock (Technical Specifications)","url":"https://www.trex-arms.com/store/b5-systems-bravo-stock-844455","retrieved":"2026-10-05","via":"harvest"}}],"adopt":{"from":"b5","reason":"The maker's page; the two sellers repeat it."},"note":"From the butt pad's rearmost point to the front of the tube housing. Against the height it reads 1.2% long in B5's side photo and in the patent's side view alike (both 1.45 x the height: 7.11 in for 4.9): inside the rounding of the two figures."},"height":{"label":"Height","kind":"length","measurements":[{"id":"b5","value":4.9,"unit":"in","stated":"Height: 4.9 in","source":{"type":"spec","publisher":"manufacturer","name":"B5 Systems, BRAVO STOCK (the page's 'specs' list)","url":"https://b5systems.com/collection/ar/bravo-stock/","retrieved":"2026-10-05","via":"harvest"}},{"id":"wing","value":4.9,"unit":"in","stated":"Height: 4.9\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, B5 Systems Bravo Stock (MPN: BRV-1082 / BRV-1085 / BRV-1104)","url":"https://www.wingtactical.com/firearm-parts-accessories/ar-15-parts/ar-stocks-and-accessories/b5-systems-bravo-stock/","retrieved":"2026-10-05","via":"harvest"}},{"id":"trex","value":4.9,"unit":"in","stated":"Height 4.9 in.","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, B5 Systems BRAVO Stock (Technical Specifications)","url":"https://www.trex-arms.com/store/b5-systems-bravo-stock-844455","retrieved":"2026-10-05","via":"harvest"}}],"adopt":{"from":"b5","reason":"The maker's page; the two sellers repeat it."},"note":"From the cheek's top to the toe (the lever's tip and the lock pin's end hang 3.9 and 3.1 in below the top: inside it)."},"width":{"label":"Width","kind":"length","measurements":[{"id":"b5","value":2,"unit":"in","stated":"Width: 2 in","source":{"type":"spec","publisher":"manufacturer","name":"B5 Systems, BRAVO STOCK (the page's 'specs' list)","url":"https://b5systems.com/collection/ar/bravo-stock/","retrieved":"2026-10-05","via":"harvest"},"note":"Written to the whole inch, so its ± is half an inch as stated; the patent's end view at the height's scale says 2.00."},{"id":"wing","value":2,"unit":"in","stated":"Width: 2\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, B5 Systems Bravo Stock (MPN: BRV-1082 / BRV-1085 / BRV-1104)","url":"https://www.wingtactical.com/firearm-parts-accessories/ar-15-parts/ar-stocks-and-accessories/b5-systems-bravo-stock/","retrieved":"2026-10-05","via":"harvest"}},{"id":"trex","value":2,"unit":"in","pm":0.05,"stated":"Width 2.0 in.","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, B5 Systems BRAVO Stock (Technical Specifications)","url":"https://www.trex-arms.com/store/b5-systems-bravo-stock-844455","retrieved":"2026-10-05","via":"harvest"}}],"adopt":{"from":"b5","reason":"The maker's page; the sellers repeat it, one of them to the tenth."},"note":"Across the cheek's two wings, the widest place: the patent's end views, scaled by the height, are 2.00 in across them (544 px against 1331 for 4.9 in) and 1.51 across the butt pad. B5 writes it without a decimal; T.REX ARMS writes 2.0."},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"b5","value":9.3,"unit":"oz","stated":"Weight: 9.3 oz","source":{"type":"spec","publisher":"manufacturer","name":"B5 Systems, BRAVO STOCK (the page's 'specs' list)","url":"https://b5systems.com/collection/ar/bravo-stock/","retrieved":"2026-10-05","via":"harvest"}},{"id":"b5-shop-table","value":12,"unit":"oz","stated":"Weight 12 oz","source":{"type":"spec","publisher":"manufacturer","name":"B5 Systems, BRAVO STOCK (the page's 'Additional information' table)","url":"https://b5systems.com/collection/ar/bravo-stock/","retrieved":"2026-10-05","via":"harvest"},"note":"The shop's product-data table under the description, beside the colour list; not the 'specs' list."},{"id":"wing","value":9.3,"unit":"oz","stated":"Weight: 9.3 oz.","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, B5 Systems Bravo Stock (MPN: BRV-1082 / BRV-1085 / BRV-1104)","url":"https://www.wingtactical.com/firearm-parts-accessories/ar-15-parts/ar-stocks-and-accessories/b5-systems-bravo-stock/","retrieved":"2026-10-05","via":"harvest"}},{"id":"trex","value":9.3,"unit":"oz","stated":"Weight 9.3 oz.","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, B5 Systems BRAVO Stock (Technical Specifications)","url":"https://www.trex-arms.com/store/b5-systems-bravo-stock-844455","retrieved":"2026-10-05","via":"harvest"}},{"id":"primary-arms","value":9.6,"unit":"oz","stated":"9.6 oz weight","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, B5 Systems Bravo Collapsible AR-15 Stock - Carbine (SKU BRV-201-01-BLK, MPN BRV-1082)","url":"https://www.primaryarms.com/b5-systems-bravo-stock-mil-spec-black","retrieved":"2026-10-05","via":"harvest"},"note":"Its table says the same: 'Weight 9.6 Oz'."},{"id":"ar15discounts","value":9.6,"unit":"oz","stated":"Weight 9.6 oz","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, B5 Systems BRAVO Black Mil-Spec Stock - OEM - BRV-1082 (Additional information)","url":"https://ar15discounts.com/products/b5-systems-bravo-black-mil-spec-stock-oem/","retrieved":"2026-10-05","via":"harvest"},"note":"Beside 'Dimensions 10.6 × 7 × 2.1 in', which is not the stock's size (a package's, by its 10.6 in)."},{"id":"jerking-the-trigger","value":8.25,"unit":"oz","stated":"The Bravo weighs 8.25 ounces which is 2 ounces less than the Enhanced SOPMOD Stock at 10.25 ounces.","source":{"type":"spec","publisher":"review","name":"Jerking the Trigger, Review: B5 Systems Bravo SOPMOD Stock (2012-12-19)","url":"https://jerkingthetrigger.com/2012/12/19/review-b5-systems-bravo-sopmod-stock/","retrieved":"2026-10-05","via":"harvest"},"note":"The stock as first sold; how it was weighed isn't said."},{"id":"captain-berz","value":8.25,"unit":"oz","stated":"The B5 Systems Bravo Stock weighs 8.25 ounces.","source":{"type":"spec","publisher":"review","name":"Captain Berz, B5 Systems Bravo Stock (2017-02-13)","url":"https://www.captainberz.com/single-post/2017/02/13/b5-systems-bravo-stock","retrieved":"2026-10-05","via":"harvest"},"note":"The same figure as the 2012 review, no method."}],"adopt":{"from":"b5","reason":"The maker's own figure for the stock, in the list with its sizes; Wing Tactical, T.REX ARMS and Scheels repeat it. The 12 oz beside it is the shop table's and no one else's; 9.6 is two sellers' and 8.25 two reviewers' of the stock years ago, none measured on file."},"note":"B5's page states two: 9.3 oz in the product's 'specs' list and 12 oz in the shop's 'Additional information' table, which is the shop system's own weight field (the same 12 oz stands on each of the nine colours in the page's variation data; no seller repeats it). Sellers carry 9.3 and 9.6; two reviews of the stock as it was in 2012 and 2017 say 8.25, neither saying how it was weighed."},"tube_axis_below_top":{"label":"Tube axis below the stock's top edge","kind":"length","measurements":[{"id":"patent","value":0.677,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/b5-bravo-stock 38a078250167 (US D722,669 S, sheet 2 of 8, FIG. 2 front view, 300 dpi)","scaleRef":"the figure's height and width = B5's 4.9 and 2 in (1331 px → 271.6 px/in and 544 px → 272.5 px/in: within 0.4%)","method":"least-squares circle through the dashed (hidden) bore, 280 points over its upper 236° (rms 0.55 px): its centre 183.8 px below the outline's top and 0.1 px off the figure's middle (.cache/batch123/b5-bravo-stock/bore.py; the overlay was looked at); ± for the scale's two references and the dashes","via":"harvest"}}],"note":"The patent's front view draws the bore as a hidden-line circle: its centre is the tube's axis. The circle reads 1.162 in across at the scale B5's height and width give (bore_diameter): the mil-spec tube with 0.014 in to spare, which is the check of that scale. No photo on file shows the stock on a tube square from the side."},"bore_diameter":{"label":"The bore for the receiver extension, as the patent draws it","kind":"length","measurements":[{"id":"patent","value":1.162,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/b5-bravo-stock 38a078250167 (US D722,669 S, sheet 2 of 8, FIG. 2 front view, 300 dpi)","scaleRef":"the figure's height and width = B5's 4.9 and 2 in (271.6 and 272.5 px/in)","method":"the diameter of the least-squares circle through the dashed (hidden) bore: 315.7 px (280 points, rms 0.55 px)","via":"harvest"}}],"note":"A check of the end view's scale, not a fit: B5 publishes no bore, only 'Fits MIL-SPEC Carbine Receiver Extensions' (std.receiver_extension.milspec_od is 1.148). The mouth the front view draws in solid lines is wider (a keyhole with the indexing rail's channel under it, its floor 0.93 in below the axis: the tube's rail reaches 0.874)."},"rail_channel_width":{"label":"Width of the channel under the bore, for the receiver extension's indexing rail","kind":"length","measurements":[{"id":"patent","value":0.53,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/b5-bravo-stock 38a078250167 (US D722,669 S, sheet 2 of 8, FIG. 2 front view, 300 dpi)","scaleRef":"the figure's height and width = B5's 4.9 and 2 in (271.6 and 272.5 px/in)","method":"the keyhole's neck: its two solid lines read across the figure 0.86 in below the bore's centre, 144.5 px apart (sheet rows 2278.5 and 2423); ± a stroke each side","via":"harvest"}}],"note":"The mouth the patent's front view draws is a keyhole: the bore and this channel under it. The mil-spec tube's rail is 0.49 in wide (std.receiver_extension.rail_width): 0.02 to spare each side."},"rail_channel_floor_below_axis":{"label":"Floor of the indexing rail's channel, below the tube axis","kind":"length","measurements":[{"id":"patent","value":0.932,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/b5-bravo-stock 38a078250167 (US D722,669 S, sheet 2 of 8, FIG. 2 front view, 300 dpi)","scaleRef":"the figure's height and width = B5's 4.9 and 2 in (271.6 and 272.5 px/in)","method":"the first line across the channel below the bore (sheet column 942), 253.2 px below the fitted centre of the dashed bore (.cache/batch123/b5-bravo-stock/bore.py)","via":"harvest"}}],"note":"The mil-spec tube's rail reaches 0.874 in below its axis (std.receiver_extension.rail_bottom_below_axis): 0.06 to spare. The next line down in the same view, 0.976 below the axis, is the cheek's flat underside, where the side photo has it (1.65 in below the top)."},"top_hole_ahead_of_butt":{"label":"Round hole on the cheek's top: its centre ahead of the butt","kind":"length","measurements":[{"id":"patent","value":5.186,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/b5-bravo-stock 41ee3b82c602 (US D722,669 S, sheet 4 of 8, FIG. 5 top view, 300 dpi)","scaleRef":"the figure's length and width = B5's 7.2 and 2 in (2014 px → 279.7 px/in and 567 px → 283.5: within 1.4%, mean 281.6)","method":"least-squares circle through the dashed hole (556 inked px, rms 1.6 px): its centre 1460.4 px from the pad's rear and 0.5 px off the middle; ± is the two scales' spread (5.15 to 5.22)","via":"harvest"}}],"note":"The patent draws it in broken lines; a seller's photo from above shows it on the stock (Wing Tactical 54174). It stands over the lock pin: 0.725 of the stock's length from the butt in the patent's top view, against 0.720 for the pin in B5's side photo (lock_pin_ahead_of_butt): two sources, 0.03 in apart."},"top_hole_diameter":{"label":"Round hole on the cheek's top: its diameter","kind":"length","measurements":[{"id":"patent","value":0.32,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/b5-bravo-stock 41ee3b82c602 (US D722,669 S, sheet 4 of 8, FIG. 5 top view, 300 dpi)","scaleRef":"the figure's length and width = B5's 7.2 and 2 in (279.7 and 283.5 px/in, mean 281.6)","method":"the diameter of the least-squares circle through the dashed hole: 90.2 px; ± for the dashes (rms 1.6 px) and the scale","via":"harvest"}}]},"release_tab_span":{"label":"Butt pad's release tabs: across their two outer faces","kind":"length","measurements":[{"id":"patent","value":1.03,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/b5-bravo-stock 38a078250167 (US D722,669 S, sheet 2 of 8, FIG. 2 front view, 300 dpi)","scaleRef":"the figure's height and width = B5's 4.9 and 2 in (271.6 and 272.5 px/in)","method":"the two dashed boxes beside the frame: their outer lines 0.521 and 0.510 in from the middle (sheet rows 2205.5 and 2485.5; the middle 2347), their inner 0.34 and 0.37; ± a stroke each side (.cache/batch123/b5-bravo-stock/hole.py)","via":"harvest"}}],"note":"B5's sheet: 'Remove the buttpad by squeezing the tabs firmly and applying pressure', and its drawing's label BUTTPAD RELEASE TABS points at this block. One each side of the frame's web, ahead of the plate the pad sits on; the side photo gives their outline (3.26 to 3.76 in below the top, where the patent's front view has them: 3.23 to 3.75)."},"lock_pin_ahead_of_butt":{"label":"Lock pin ahead of the butt's rearmost point","kind":"length","measurements":[{"id":"photo","value":5.154,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/b5-bravo-stock c9a15e250f11 (B5: BRV-1082_PROFILE_RIGHT.png, straight right side on a transparent ground, 2000 x 2000)","scaleRef":"the stock's own length and height, 1509 px for B5's 7.2 in and 1040 px for 4.9 in: 209.6 and 212.2 px/in, mean 210.9","method":"the pin's lower end is the block under the lever in the silhouette, columns 1287 to 1377 (0.43 in across, its foot 3.07 in below the top): its middle, column 1332, is 1087 px ahead of the pad's rearmost point (column 245) and 421 px (2.00 in) behind the front; ± is the two scales' spread (5.12 to 5.19) and a pixel or two for the pin","via":"harvest"}}],"note":"The steel pin the adjustment lever draws out of the receiver extension's holes: its lower end, with the cross pin that holds the lever, hangs under the lever's front (B5's sheet: 'Pull the adjustment lever down firmly until the stock can smoothly slide onto the buffer tube'). Where it stands says which hole the stock is on."},"frame_width":{"label":"Width of the frame below the cheek: the web, its ribs, the strut and the block under the tube's front","kind":"length","measurements":[{"id":"patent","value":0.62,"unit":"in","pm":0.12,"source":{"type":"photo","photo":"references/b5-bravo-stock 0c4cb96aa6c2 (US D722,669 S, sheet 5 of 8, FIG. 6 bottom view, 300 dpi) and 38a078250167 (sheet 2, FIG. 2 front view)","scaleRef":"FIG. 6: its length and width = B5's 7.2 and 2 in (2014 px → 279.7 px/in and 567 px → 283.5: within 1.4%, mean 281.6); FIG. 2: 271.6 px/in","method":"FIG. 6: the strut's two edges read across the figure at stations along it: 0.30 in each side of the middle 2.86 in ahead of the butt, 0.33 at 2.14, 0.36 at 1.43; FIG. 2: the block's two edges 0.248 each side, from 1.75 to 2.45 in below the top; the value is the middle of 0.50 to 0.73 and the ± their spread (.cache/batch123/b5-bravo-stock/measure.py, block.py)","via":"harvest"}}],"note":"The cheek round the tube is the full 2 in across its wings and the butt pad 1.51; the frame between them is much thinner and not one width: the patent's bottom view shows the strut 0.58 in wide behind the lever, widening to 0.73 near the butt, and its front view shows the block under the tube's front 0.50 wide. One figure is used."},"keel_width":{"label":"Width of the cheek's flat underside, between the wings' undersides","kind":"length","measurements":[{"id":"patent","value":0.99,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/b5-bravo-stock 0c4cb96aa6c2 (US D722,669 S, sheet 5 of 8, FIG. 6 bottom view, 300 dpi)","scaleRef":"the figure's length and width = B5's 7.2 and 2 in (279.7 and 283.5 px/in: within 1.4%, mean 281.6)","method":"the pair of lines each side of the middle that run straight from 1.4 to 5.7 in ahead of the butt: the outer 0.497 in out, the inner 0.47; the outer is taken, ± the pair's gap","via":"harvest"}}],"note":"The wings' undersides slope in from their tips to this flat, which the frame hangs from. In the end views the butt pad hides it; the bottom view shows its two edges running the stock's length."},"lever_width":{"label":"Width of the adjustment lever","kind":"length","measurements":[{"id":"patent-bottom","value":0.86,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/b5-bravo-stock 0c4cb96aa6c2 (US D722,669 S, sheet 5 of 8, FIG. 6 bottom view, 300 dpi)","scaleRef":"the figure's length and width = B5's 7.2 and 2 in (279.7 and 283.5 px/in, mean 281.6)","method":"the lever's two long edges, 0.431 in each side of the middle at 3.58 and 4.29 in ahead of the butt (a second line 0.02 inside each is its edge's round)","via":"harvest"}},{"id":"patent-front","value":0.85,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/b5-bravo-stock 38a078250167 (US D722,669 S, sheet 2 of 8, FIG. 2 front view, 300 dpi)","scaleRef":"the figure's height and width = B5's 4.9 and 2 in (271.6 and 272.5 px/in)","method":"the lever's outer edges read across the figure 2.95 to 3.5 in below the top: 0.42 to 0.43 in each side of the middle","via":"harvest"}}],"adopt":{"from":"patent-bottom","reason":"The view square to the lever's width along its whole length; the front view, at its own scale, agrees within 0.01 in."}},"butt_behind_pin_pos1":{"label":"Butt behind the takedown pin at position 1 (collapsed), on a carbine receiver extension","kind":"length","measurements":[{"id":"holes","value":9.333,"unit":"in","pm":0.08,"source":{"type":"derived","expr":"{bcm-receiver-extension.tube_front_behind_pin} + {bcm-receiver-extension.tube_length} - {bcm-receiver-extension.position_hole_rear_from_rear} - 5 * {bcm-receiver-extension.position_step} + {.lock_pin_ahead_of_butt}","via":"harvest"},"note":"The lock pin in the tube's front hole. ± for the hole's place (0.03), the tube's seat (0.02) and the pin's place in the stock (0.04), and for the tube's length, which is a generic figure."}],"note":"No photo on file shows the stock on a rifle square from the side, so it is seated by its lock pin in the tube's front hole: where the Army's drawings seat the tube and BCM's photo places its holes (bcm-stock-kit), and where the pin stands in the stock in B5's own side photo. That leaves its front 0.51 in behind the castle nut (bcm-castle-nut.rear_face_behind_pin): the pin stands 2.00 in behind the front in the same photo. B5 publishes no length of pull."},"lop_collapsed":{"label":"Length of pull, collapsed (the maker's reference rifle)","kind":"length","measurements":[],"note":"B5 publishes none (its page, its installation sheet and six sellers' pages read 2026-10-05)."},"lop_extended":{"label":"Length of pull, extended (the maker's reference rifle)","kind":"length","measurements":[],"note":"B5 publishes none."},"frame_rim_width":{"label":"Width of the frame's rim round the web, in the side view (the strut, the front and the bottom of the panel ahead of the lever)","kind":"length","measurements":[{"id":"photo","value":0.19,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/b5-bravo-stock c9a15e250f11 (B5: BRV-1082_PROFILE_RIGHT.png, straight right side, 2000 x 2000)","scaleRef":"the trace's placement: B5's 7.2 and 4.9 in on the outline, 210.9 px/in (the same plane as the strut's face)","method":"grey levels along two lines square to the strut (from (760, 1290) and (680, 1355), toward the upper left): the outline at 0, the inner wall's dark line at 40.5 and 39.5 px; ± for the edges, 2 px each (.cache/night-2026-10-19/detail/lines.py)","via":"harvest"}}],"note":"Across the strut, square to it, from its lower edge (the outline) to the inner edge of its face, where the rim's inner wall begins in shadow. The rim along the front and the bottom of the panel ahead of the lever is drawn at the same width (an earlier reading of it was about 0.17 in, not entered). Along the pad's plate the web meets the plate's own face: no rim of its own."},"rib_width":{"label":"Width of the rib across the triangle (in the side view, across it)","kind":"length","measurements":[{"id":"photo","value":0.066,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/b5-bravo-stock c9a15e250f11 (B5: BRV-1082_PROFILE_RIGHT.png, straight right side, 2000 x 2000)","scaleRef":"the trace's placement, 210.9 px/in","method":"grey levels along four lines square to the rib (at columns 480, 540, 720 and 780): from its lit edge to where its face falls into the shadow it casts, 15, 14.5, 13.5 and 13 px; ± two pixels","via":"harvest"}}],"note":"One straight rib, from the triangle's top rear corner, under the cheek, through the QD socket's boss to the strut (the photos of all five colours have it in the body's colour). Its face is lit on one side and shadowed on the other in the side photo."},"web_thickness":{"label":"Thickness of the frame's web, at the stock's middle (the floor of the panels each side)","kind":"length","measurements":[{"id":"photo","value":0.07,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/b5-bravo-stock c1bb9e3fa345 (T.REX ARMS, B5-BRAVO-Stock-2.jpg: the coyote stock's left side from ahead and a little below, on a blue-grey board, 3000 x 3000)","scaleRef":"a pinhole camera fitted to the photo by the model's outline (silhouettes 96% the same; lens about 40 in off, 25 degrees ahead of square and 16 below): across the upper sling slot it gives 205 px for an inch of the side's height and 64 px for an inch out of the side","method":"grey levels along four lines square to the upper slot (from (1660, 1342) to (1765, 1270), along (0.583, 0.812)): its near rim's edge on the far side of the opening (the lit wall ends) at 18.5 px, the opening (black) from 23 to 59.5; the far rim stands 4.5 px off the near one: 4.5 / 64 in, the web's two faces apart (.cache/night-2026-10-19/detail/lines.py, camfit.py)","via":"harvest"}}],"note":"Read through a sling slot, which is cut through the web: from the camera of c1bb9e3fa345 the slot's far rim shows 4.5 px from its near rim, square to the slot's length, where a web as thick as the frame (0.62 in) would put it 39 px off and leave no opening at all; the opening shows 36 px across of the slot's 37. The web is thin and the panels each side of it are deep: from the frame's face to the web, 0.27 in. ± for two picks of 2 px each and a tenth for the camera."},"qd_boss_diameter":{"label":"The QD socket's boss: diameter of its face","kind":"length","measurements":[{"id":"photo","value":0.692,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/b5-bravo-stock c9a15e250f11 (B5: BRV-1082_PROFILE_RIGHT.png, straight right side, 2000 x 2000)","scaleRef":"the trace's placement, 210.9 px/in","method":"grey levels along row 1022 and column 631 through the socket's middle: the face's edge at 73 px from the middle each way (columns 558 and 704; rows 949 and 1094.5): 146 px","via":"harvest"}}],"note":"A round boss on the rib, under the socket's steel; on the five colours' pictures it is the body's colour. Square from the side its face is ringed by a dark band out to qd_boss_foot_diameter, the same width all round: its wall, drafted (wider at its foot), which a square view sees only by its draft."},"qd_boss_foot_diameter":{"label":"The QD socket's boss: diameter at its foot, on the web","kind":"length","measurements":[{"id":"photo","value":0.806,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/b5-bravo-stock c9a15e250f11 (B5: BRV-1082_PROFILE_RIGHT.png, straight right side, 2000 x 2000)","scaleRef":"the trace's placement, 210.9 px/in","method":"the outer edge of the dark band round the boss, 84 to 85 px from the middle on all four sides (row 1022: columns 546 and 716; column 631: rows 937 and 1106): 170 px; read as the wall's foot, not a shadow, because it is the same width on the lit side and the shadowed one","via":"harvest"}}]},"relief_face_inset":{"label":"How far the rib's face, the QD boss's face and the lock pin's housing stand in from the frame's face","kind":"length","measurements":[{"id":"assumed","value":0,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the rib and the QD boss flush with the frame's rim. The rib's reading through c1bb9e3fa345 agrees within its ±; the boss's height isn't read (the note).","via":"harvest"}}],"note":"ASSUMED, all three: the rib and the boss are drawn flush with the frame's rim (0.31 in from the middle), the housing round to its own radius. Through the camera of c1bb9e3fa345 the rib shows its face and one wall about 20 px across where its face alone would be 13, a wall 0.2 in tall to within 0.12: the flush rim's 0.27 above the web is inside that. Under the boss in the same photo its wall shows only 8 px, but that is where the rib runs into it, whose face meets the boss's there: it says nothing of the boss's height. From behind and above (0e3fd31de154) the boss's wall shows broad on the side away from the rib, as a drum standing to the rim's face would; the camera fitted to that photo by the outline (95% agreement) left the lever's outline a quarter of an inch off the photo's and wasn't read. No view on file is square across the frame."}}},{"subject":"b5-enhanced-sopmod-stock","title":"B5 Systems Enhanced SOPMOD Stock","dimensions":{"length":{"label":"Overall length","kind":"length","measurements":[{"id":"b5","value":7.43,"unit":"in","stated":"Length: 7.43 in","source":{"type":"spec","publisher":"manufacturer","name":"B5 Systems, ENHANCED SOPMOD STOCK (the page's 'specs' list)","url":"https://b5systems.com/collection/ar/enhanced-sopmod-stock/","retrieved":"2026-10-06","via":"harvest"}},{"id":"wing","value":7.4,"unit":"in","stated":"Length: 7.4\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, B5 Systems Enhanced SOPMOD Stock (MPN: SOP-1074 / SOP-1075 / SOP-1097)","url":"https://www.wingtactical.com/firearm-parts-accessories/ar-15-parts/ar-stocks-and-accessories/b5-systems-enhanced-sopmod-stock/","retrieved":"2026-10-06","via":"harvest"}},{"id":"trex","value":7.4,"unit":"in","stated":"Length 7.4 in.","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, B5 Systems Enhanced SOPMOD Stock (Technical Specifications)","url":"https://www.trex-arms.com/store/b5-systems-enhanced-sopmod-stock-844470","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"b5","reason":"The maker's page, to the hundredth; the two sellers round it."},"note":"From the butt pad's rearmost point to the housing's foremost, which is the front of its wings at the height where they are widest; the storage tubes' caps end 0.03 in behind it in B5's side photo."},"height":{"label":"Height","kind":"length","measurements":[{"id":"b5","value":4.93,"unit":"in","stated":"Height: 4.93 in","source":{"type":"spec","publisher":"manufacturer","name":"B5 Systems, ENHANCED SOPMOD STOCK (the page's 'specs' list)","url":"https://b5systems.com/collection/ar/enhanced-sopmod-stock/","retrieved":"2026-10-06","via":"harvest"}},{"id":"wing","value":4.9,"unit":"in","stated":"Height: 4.9\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, B5 Systems Enhanced SOPMOD Stock (MPN: SOP-1074 / SOP-1075 / SOP-1097)","url":"https://www.wingtactical.com/firearm-parts-accessories/ar-15-parts/ar-stocks-and-accessories/b5-systems-enhanced-sopmod-stock/","retrieved":"2026-10-06","via":"harvest"}},{"id":"trex","value":4.9,"unit":"in","stated":"Height 4.9 in.","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, B5 Systems Enhanced SOPMOD Stock (Technical Specifications)","url":"https://www.trex-arms.com/store/b5-systems-enhanced-sopmod-stock-844470","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"b5","reason":"The maker's page, to the hundredth; the two sellers round it."},"note":"From the housing's top to the butt pad's toe (the lever's tip hangs 3.4 in below the top, the stud under it 3.1: inside it)."},"width":{"label":"Width","kind":"length","measurements":[{"id":"b5","value":2.4,"unit":"in","stated":"Width: 2.4 in","source":{"type":"spec","publisher":"manufacturer","name":"B5 Systems, ENHANCED SOPMOD STOCK (the page's 'specs' list)","url":"https://b5systems.com/collection/ar/enhanced-sopmod-stock/","retrieved":"2026-10-06","via":"harvest"}},{"id":"wing","value":2.4,"unit":"in","stated":"Width: 2.4\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, B5 Systems Enhanced SOPMOD Stock (MPN: SOP-1074 / SOP-1075 / SOP-1097)","url":"https://www.wingtactical.com/firearm-parts-accessories/ar-15-parts/ar-stocks-and-accessories/b5-systems-enhanced-sopmod-stock/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"b5","reason":"The maker's page; the seller repeats it."},"note":"Across the two wings that hold the storage tubes, the widest place: the patent's back view is 684 px wide there against 1394 px high (2.42 in for 4.93), its top view 685 against 2113 long (2.41 for 7.43). The butt pad is 1.50 in wide in the same views. No page says what the 2.4 is measured across; the patent does."},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"b5","value":12.2,"unit":"oz","stated":"Weight: 12.2 oz","source":{"type":"spec","publisher":"manufacturer","name":"B5 Systems, ENHANCED SOPMOD STOCK (the page's 'specs' list)","url":"https://b5systems.com/collection/ar/enhanced-sopmod-stock/","retrieved":"2026-10-06","via":"harvest"}},{"id":"b5-shop-table","value":12,"unit":"oz","stated":"Weight 12 oz","source":{"type":"spec","publisher":"manufacturer","name":"B5 Systems, ENHANCED SOPMOD STOCK (the page's 'Additional information' table)","url":"https://b5systems.com/collection/ar/enhanced-sopmod-stock/","retrieved":"2026-10-06","via":"harvest"},"note":"The shop's product-data table under the description, beside the colour list; not the 'specs' list."},{"id":"wing","value":11.8,"unit":"oz","stated":"Weight: 11.8 oz.","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, B5 Systems Enhanced SOPMOD Stock (MPN: SOP-1074 / SOP-1075 / SOP-1097)","url":"https://www.wingtactical.com/firearm-parts-accessories/ar-15-parts/ar-stocks-and-accessories/b5-systems-enhanced-sopmod-stock/","retrieved":"2026-10-06","via":"harvest"}},{"id":"trex","value":11.8,"unit":"oz","stated":"Weight 11.8 oz.","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, B5 Systems Enhanced SOPMOD Stock (Technical Specifications)","url":"https://www.trex-arms.com/store/b5-systems-enhanced-sopmod-stock-844470","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":14.4,"unit":"oz","stated":"14.4 oz weight","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, B5 Systems SOPMOD Collapsible AR-15 Stock - Carbine - Black (SKU SOP-201-01-BLK, MPN SOP-1074)","url":"https://www.primaryarms.com/b5-systems-sopmod-ar-15-mil-spec-polymer-stock-with-quick-detach-mount-black-sop-201-01-blk","retrieved":"2026-10-06","via":"harvest"},"note":"Its table says the same: 'Weight 14.4 Oz'. No other page has it."},{"id":"recoil-2012","value":11.5,"unit":"oz","stated":"The black versions both weighed 11.5 ounces while the various colored versions deviated by about half an ounce more.","source":{"type":"spec","publisher":"review","name":"Recoil Magazine, B5 Systems Enhanced SOPMOD Stock (2012)","url":"https://www.recoilweb.com/b5-systems-enhanced-sopmod-stock-2-10331.html","retrieved":"2026-10-06","via":"harvest"},"note":"A weighing of the stock as first sold, beside another maker's SOPMOD; on what scale isn't said."}],"adopt":{"from":"b5","reason":"The maker's own figure for this stock, in the list with its sizes. The 12 oz beside it is the shop table's rounding; 11.8 is the Government Issue stock's figure on two sellers' pages; 14.4 is one seller's and no one else's; 11.5 is a 2012 stock on an unnamed scale."},"note":"B5's page states two: 12.2 oz in the product's 'specs' list and 12 oz in the shop's 'Additional information' table (the shop system's own field). Two sellers say 11.8 oz, which is what B5's page for the other SOPMOD, the SOPMOD, GOVERNMENT ISSUE, states ('Weight: 11.80 oz', with this stock's three sizes to the digit: read 2026-10-06), so it is probably that stock's figure copied. Primary Arms says 14.4; a magazine's weighing of the first Enhanced stocks in 2012 read 11.5."},"tube_axis_below_top":{"label":"Tube axis below the stock's top edge","kind":"length","measurements":[{"id":"patent","value":0.694,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/b5-enhanced-sopmod-stock f2d5af41858b (US D722,357 S, sheet 2 of 8, FIG. 3 front view, 300 dpi)","scaleRef":"the figure's height and width = B5's 4.93 and 2.4 in (1394 px → 282.8 px/in and 685 px → 285.4 px/in: within 0.9%, mean 284.1)","method":"least-squares circle through the broken-line bore, 690 inked px over its upper 240° (rms 0.64 px): its centre 197.2 px below the outline's top and 0.0 px off the figure's middle (.cache/batch5/b5-enhanced-sopmod-stock/fig3.py; the overlay was looked at); ± for the scale's two references (0.691 to 0.698) and the dashes","via":"harvest"}}],"note":"The patent's front view draws the bore as a broken-line circle: its centre is the tube's axis. The circle reads 1.161 in across at the scale B5's height and width give (bore_diameter): the mil-spec tube's 1.148 and a little, which is the check of that scale (B5's Bravo, on the same tube, read 1.162 in its own patent). No photo on file shows the stock on a tube square from the side."},"bore_diameter":{"label":"The bore for the receiver extension, as the patent draws it","kind":"length","measurements":[{"id":"patent","value":1.161,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/b5-enhanced-sopmod-stock f2d5af41858b (US D722,357 S, sheet 2 of 8, FIG. 3 front view, 300 dpi)","scaleRef":"the figure's height and width = B5's 4.93 and 2.4 in (282.8 and 285.4 px/in, mean 284.1)","method":"the diameter of the least-squares circle through the broken-line bore: 329.7 px (690 inked px, rms 0.64 px)","via":"harvest"}}],"note":"A check of the end view's scale, not a fit: B5 publishes no bore, only 'Fits MIL-SPEC Carbine Receiver Extensions' (std.receiver_extension.milspec_od is 1.148)."},"rail_channel_width":{"label":"Width of the channel under the bore, for the receiver extension's indexing rail","kind":"length","measurements":[{"id":"patent","value":0.505,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/b5-enhanced-sopmod-stock f2d5af41858b (US D722,357 S, sheet 2 of 8, FIG. 3 front view, 300 dpi)","scaleRef":"the figure's height and width = B5's 4.93 and 2.4 in (282.8 and 285.4 px/in, mean 284.1)","method":"the keyhole's neck: its two broken lines read across the figure 0.75 and 0.85 in below the bore's centre, 0.253 and 0.250 in each side of the middle; ± a stroke each side (.cache/batch5/b5-enhanced-sopmod-stock/fig3.py)","via":"harvest"}}],"note":"The opening the patent's front view draws in broken lines is a keyhole: the bore and this channel under it. The mil-spec tube's rail is 0.49 in wide (std.receiver_extension.rail_width)."},"rail_channel_floor_below_axis":{"label":"Floor of the indexing rail's channel, below the tube axis","kind":"length","measurements":[{"id":"patent","value":0.881,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/b5-enhanced-sopmod-stock f2d5af41858b (US D722,357 S, sheet 2 of 8, FIG. 3 front view, 300 dpi)","scaleRef":"the figure's height and width = B5's 4.93 and 2.4 in (282.8 and 285.4 px/in, mean 284.1)","method":"the broken line across the channel under the bore, read down the figure's middle and 30 px beside it: 0.879 to 0.883 in below the fitted centre of the bore (.cache/batch5/b5-enhanced-sopmod-stock/fig3.py)","via":"harvest"}}],"note":"The mil-spec tube's rail reaches 0.874 in below its axis (std.receiver_extension.rail_bottom_below_axis): the drawing leaves 0.007 in, less than its strokes are wide. The next line down, 1.018 below the axis, is the top of the block the lock pin stands in."},"storage_axis_below_top":{"label":"Storage tubes' axis below the stock's top edge","kind":"length","measurements":[{"id":"patent","value":1.478,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/b5-enhanced-sopmod-stock f2d5af41858b (US D722,357 S, sheet 2 of 8, FIG. 2 back view and FIG. 3 front view, 300 dpi)","scaleRef":"each figure's height and width = B5's 4.93 and 2.4 in (FIG. 2: 282.8 and 285.0 px/in; FIG. 3: 282.8 and 285.4)","method":"least-squares circle through each wing tip's outer arc (the outermost ink of each row within 45 px of the tip, 190 rows, rms 0.4 px): the four centres (two wings, two figures) 419.7 to 419.8 px below the outline's top (.cache/batch5/b5-enhanced-sopmod-stock/fig3.py; the overlay was looked at); ± for the scale's two references","via":"harvest"}},{"id":"photo","value":1.49,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/b5-enhanced-sopmod-stock 9bc66a9c7cdd (B5: SOP-1074_PROFILE_RIGHT.png, right side on a transparent ground, 2000 x 2000)","scaleRef":"the stock's own length and height, 1582 px for B5's 7.43 in and 1042 px for 4.93 in: 212.9 and 211.4 px/in, mean 212.2","method":"the cap's dome past the housing's front reaches furthest forward at row 805 (its silhouette's rows 750 to 880, read every 10); the housing's top edge above it is row 489 (the photo is turned 0.36°, so the top is read where the cap is): 316 px; ± 5 px for the dome's flat crown","via":"harvest"}}],"adopt":{"from":"patent","reason":"An arc fitted over 190 rows in a line drawing, the same in both wings and both end views; the photo's cap, read at its crown, agrees within 0.012 in."},"note":"Each wing's tip is round about the storage tube it holds: the arc's centre is the tube's axis. Two sources: the patent's end views, and the cap that shows past the housing's front in B5's side photo."},"storage_axis_off_centre":{"label":"Storage tubes' axis out from the stock's middle","kind":"length","measurements":[{"id":"patent","value":0.726,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/b5-enhanced-sopmod-stock f2d5af41858b (US D722,357 S, sheet 2 of 8, FIG. 2 back view and FIG. 3 front view, 300 dpi)","scaleRef":"each figure's height and width = B5's 4.93 and 2.4 in (FIG. 2: 282.8 and 285.0 px/in; FIG. 3: 282.8 and 285.4)","method":"the centres of the circles through the wing tips' outer arcs: 206.0 to 206.7 px each side of the figure's middle (0.725 to 0.728 in)","via":"harvest"}}]},"wing_tip_radius":{"label":"Radius of each wing's round tip","kind":"length","measurements":[{"id":"patent","value":0.475,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/b5-enhanced-sopmod-stock f2d5af41858b (US D722,357 S, sheet 2 of 8, FIG. 2 back view and FIG. 3 front view, 300 dpi)","scaleRef":"each figure's height and width = B5's 4.93 and 2.4 in (FIG. 2: 282.8 and 285.0 px/in; FIG. 3: 282.8 and 285.4)","method":"the radii of the circles through the wing tips' outer arcs: 134.7 to 135.2 px","via":"harvest"}}],"note":"With storage_axis_off_centre it gives the width back: 2 x (0.726 + 0.475) = 2.40 in."},"storage_pocket_diameter":{"label":"Storage compartments: diameter of the round each wing's opening leaves at its tip","kind":"length","measurements":[{"id":"patent","value":0.762,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/b5-enhanced-sopmod-stock f2d5af41858b (US D722,357 S, sheet 2 of 8, FIG. 3 front view, 300 dpi)","scaleRef":"the figure's height and width = B5's 4.93 and 2.4 in (282.8 and 285.4 px/in, mean 284.1)","method":"on the row through the tip arcs' centres the wall's outer line is 1.200 in from the middle and its inner 1.107 (both wings): the inner edge is 0.381 in from the arc's centre, twice that across; ± a stroke each side","via":"harvest"}}],"note":"The patent's front view draws each wing as a wall round an opening; at the tip the opening's edge is an arc about the same centre as the outside. A CR123 cell is 0.67 in across, and T.REX ARMS says each compartment 'will fit 3 CR123s'. The storage tubes themselves aren't in the patent, and no page gives their size."},"storage_cap_diameter":{"label":"Storage tubes' caps: diameter","kind":"length","measurements":[{"id":"photo","value":0.66,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/b5-enhanced-sopmod-stock 9bc66a9c7cdd (B5: SOP-1074_PROFILE_RIGHT.png, right side on a transparent ground, 2000 x 2000)","scaleRef":"the stock's own length and height: 212.9 and 211.4 px/in, mean 212.2","method":"the cap's silhouette past the housing's front edge spans rows 745 to 885 (140 px); its upper end is where it comes out from behind the housing, so the figure is a least one; ± 8 px","via":"harvest"}}],"note":"B5: 'Dual Water Resistant Storage Compartments'; its sheet: 'Rotate the tabs inward and pull.' The caps are the tubes' front ends, one in each wing's opening; only B5's side photos show one square on, and its upper edge is behind the housing's front."},"storage_cap_front_ahead_of_butt":{"label":"Storage tubes' caps: front ahead of the butt's rearmost point","kind":"length","measurements":[{"id":"photo","value":7.39,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/b5-enhanced-sopmod-stock 9bc66a9c7cdd (B5: SOP-1074_PROFILE_RIGHT.png, right side on a transparent ground, 2000 x 2000)","scaleRef":"the stock's own length and height: 212.9 and 211.4 px/in, mean 212.2","method":"the cap's foremost column, 1783, against the pad's rearmost, 209, and the housing's foremost, 1790: 1574 px; ± the two scales' spread and a pixel or two","via":"harvest"}}]},"top_hole_ahead_of_butt":{"label":"Round hole on the housing's top: its centre ahead of the butt","kind":"length","measurements":[{"id":"photo-right","value":5.158,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/b5-enhanced-sopmod-stock 9bc66a9c7cdd (B5: SOP-1074_PROFILE_RIGHT.png, right side on a transparent ground, 2000 x 2000)","scaleRef":"the stock's own length and height: 212.9 and 211.4 px/in, mean 212.2","method":"the top edge read to a tenth of a pixel in each column, less a line fitted to it either side: a dip 3.9 px deep whose half-depth columns are 1278 to 1329; their middle, 1303.5, is 1094.5 px ahead of the pad's rearmost point (column 209); ± the two scales' spread and two pixels","via":"harvest"}},{"id":"photo-left","value":5.179,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/b5-enhanced-sopmod-stock 325eed07a69c (B5: SOP-1074_PROFILE_LEFT.png, left side on a transparent ground, 2000 x 2000)","scaleRef":"the stock's own length and height, 1594 px for 7.43 in and 1050 px for 4.93 in: 214.5 and 213.0 px/in, mean 213.8","method":"the same reading on the other side's photo: a dip 4.8 px deep, half-depth columns 662 to 716, their middle 1107 px ahead of the pad's rearmost point (column 1796)","via":"harvest"}}],"adopt":{"from":"photo-right","reason":"The photo the side outline is traced from; the other side's agrees within 0.02 in."},"note":"Sellers' photos from above show a round hole on the top near the front (Wing Tactical 54600 and 54210); the patent's top view doesn't draw it. Square from the side it is a dip in the top edge, where the hole's rim crosses the crown. It stands over the lock pin (lock_pin_ahead_of_butt, 5.13), as the Bravo's does."},"top_hole_diameter":{"label":"Round hole on the housing's top: its diameter","kind":"length","measurements":[{"id":"photo","value":0.34,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/b5-enhanced-sopmod-stock 9bc66a9c7cdd (B5: SOP-1074_PROFILE_RIGHT.png, right side on a transparent ground, 2000 x 2000)","scaleRef":"the stock's own length and height: 212.9 and 211.4 px/in, mean 212.2","method":"the dip in the top edge, from where it leaves the fitted line to where it returns: columns 1268 to 1340, 72 px (52 px at half its depth); ± 8 px for the ends, where it is a fraction of a pixel deep","via":"harvest"}}],"note":"Read from the side only: the dip's whole width in the top edge. Its depth there, 0.018 in, is what a hole 0.34 in across leaves on a crown of 0.8 in radius (the chord's sag), which is about the top's own round; the other side's photo has the dip 0.022 deep. No view from straight above is on file; T.REX ARMS' photo from above and behind (B5-SOPMOD-Stock-1.jpg) shows a plain round hole with a straight wall, no countersink, so the dip is the hole's own."},"frame_width":{"label":"Width of the frame below the housing: the web the slots and the QD socket are in","kind":"length","measurements":[{"id":"patent","value":0.5,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/b5-enhanced-sopmod-stock e42da4d67b42 (US D722,357 S, sheet 5 of 8, FIG. 6 bottom view, 300 dpi)","scaleRef":"the figure's length and width = B5's 7.43 and 2.4 in (2113 px → 284.4 px/in and 684 px → 285.0: within 0.2%, mean 284.7)","method":"the strut's two edges read across the figure 2.5 and 3.0 in ahead of the butt, behind the lever: 0.249 in each side of the middle (a second line 0.02 inside each is its edge's round) (.cache/batch5/b5-enhanced-sopmod-stock/fig6.py)","via":"harvest"}}],"note":"The housing is 2.4 in across its wings and the butt pad 1.50; the frame between them is a web, with the strut along its lower edge widening toward the pad's toe (strut_width_at_plate)."},"strut_width_at_plate":{"label":"Width of the frame's strut where it meets the plate the pad sits on","kind":"length","measurements":[{"id":"patent","value":0.995,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/b5-enhanced-sopmod-stock e42da4d67b42 (US D722,357 S, sheet 5 of 8, FIG. 6 bottom view, 300 dpi)","scaleRef":"the figure's length and width = B5's 7.43 and 2.4 in (284.4 and 285.0 px/in, mean 284.7)","method":"the strut's edges read across the figure 0.8 in ahead of the butt, 0.485 in each side of the middle (lines 0.014 outside and 0.018 inside each are its edge's round), carried the 0.08 in to the plate's face at the 0.158 in per inch they spread by: 0.498 each side (.cache/batch5/b5-enhanced-sopmod-stock/fig6.py)","via":"harvest"}}],"note":"The bottom view shows the strut's edges straight and 0.50 in apart from the lever back to strut_flare_start_ahead_of_butt, then spreading evenly to the pad: 0.59 in apart 2.0 in ahead of the butt, 0.71 at 1.6, 0.84 at 1.2, 0.97 at 0.8, and on to the plate's front face, which the same view draws 0.72 in ahead of the butt. The front view shows the same spread from below the lever to the toe."},"strut_flare_start_ahead_of_butt":{"label":"Where the frame's strut begins to widen toward the pad, ahead of the butt","kind":"length","measurements":[{"id":"patent","value":2.29,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/b5-enhanced-sopmod-stock e42da4d67b42 (US D722,357 S, sheet 5 of 8, FIG. 6 bottom view, 300 dpi)","scaleRef":"the figure's length and width = B5's 7.43 and 2.4 in (284.4 and 285.0 px/in, mean 284.7)","method":"the strut's half-width at stations 0.8 to 2.0 in ahead of the butt (0.485, 0.453, 0.422, 0.390, 0.357, 0.327, 0.295) falls 0.158 in per inch; carried on, it meets the straight stretch's 0.249 at 2.29 in (read 0.262 at 2.2 and 0.249 at 2.5)","via":"harvest"}}]},"block_width":{"label":"Width of the block under the tube's front, which the lock pin and the lever's pivot are in","kind":"length","measurements":[{"id":"patent-front","value":0.68,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/b5-enhanced-sopmod-stock f2d5af41858b (US D722,357 S, sheet 2 of 8, FIG. 3 front view, 300 dpi)","scaleRef":"the figure's height and width = B5's 4.93 and 2.4 in (282.8 and 285.4 px/in, mean 284.1)","method":"the block's two faces read across the figure 0.70 to 0.85 in below the bore's centre: 0.340 in each side of the middle (.cache/batch5/b5-enhanced-sopmod-stock/fig3.py)","via":"harvest"}},{"id":"patent-bottom","value":0.69,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/b5-enhanced-sopmod-stock e42da4d67b42 (US D722,357 S, sheet 5 of 8, FIG. 6 bottom view, 300 dpi)","scaleRef":"the figure's length and width = B5's 7.43 and 2.4 in (284.4 and 285.0 px/in, mean 284.7)","method":"the block's edges read across the figure 6.3 to 6.8 in ahead of the butt: a pair of lines 0.334 and 0.354 in each side of the middle (its edge's round); the middle of the pair is taken","via":"harvest"}}],"adopt":{"from":"patent-front","reason":"The view square to the block's faces; the bottom view, at its own scale, agrees within 0.01 in."}},"lever_width":{"label":"Width of the adjustment lever","kind":"length","measurements":[{"id":"patent-bottom","value":0.924,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/b5-enhanced-sopmod-stock e42da4d67b42 (US D722,357 S, sheet 5 of 8, FIG. 6 bottom view, 300 dpi)","scaleRef":"the figure's length and width = B5's 7.43 and 2.4 in (284.4 and 285.0 px/in, mean 284.7)","method":"the lever's two long edges, 0.462 in each side of the middle at 3.6 to 5.8 in ahead of the butt (lines 0.02 and 0.05 inside each are its edge's round)","via":"harvest"}},{"id":"patent-front","value":0.93,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/b5-enhanced-sopmod-stock f2d5af41858b (US D722,357 S, sheet 2 of 8, FIG. 3 front view, 300 dpi)","scaleRef":"the figure's height and width = B5's 4.93 and 2.4 in (282.8 and 285.4 px/in, mean 284.1)","method":"the lever's outer edges read across the figure 2.3 to 2.8 in below the top: 0.463 to 0.466 in each side of the middle (.cache/batch5/b5-enhanced-sopmod-stock/fig3b.py)","via":"harvest"}}],"adopt":{"from":"patent-bottom","reason":"The view square to the lever's width along its whole length; the front view, at its own scale, agrees within 0.01 in."},"note":"B5: 'Sure Grip Stock Latch'; its sheet's drawing labels it ADJUSTMENT LEVER."},"qd_span":{"label":"QD sockets: across the two faces, one each side of the frame","kind":"length","measurements":[{"id":"patent","value":0.748,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/b5-enhanced-sopmod-stock e42da4d67b42 (US D722,357 S, sheet 5 of 8, FIG. 6 bottom view, 300 dpi)","scaleRef":"the figure's length and width = B5's 7.43 and 2.4 in (284.4 and 285.0 px/in, mean 284.7)","method":"the outermost lines beside the strut 1.8 and 2.0 in ahead of the butt, where the socket is in B5's side photo (its hole's centre 1.79 in ahead of the butt): 0.374 in each side of the middle; the front view has lines 0.375 to 0.378 out at the socket's height (.cache/batch5/b5-enhanced-sopmod-stock/fig6.py, fig3b.py)","via":"harvest"}}],"note":"B5: 'one piece anti-rotation quick disconnect sling mounts' and 'Fixed Sling Mounts and Steel Anti-rotational QD Mounts'. The socket stands out of the web each side; its hole is 0.38 in across in B5's side photo."},"release_tab_span":{"label":"Butt pad's release tabs: across their two outer faces","kind":"length","measurements":[{"id":"patent","value":1.032,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/b5-enhanced-sopmod-stock f2d5af41858b (US D722,357 S, sheet 2 of 8, FIG. 3 front view, 300 dpi)","scaleRef":"the figure's height and width = B5's 4.93 and 2.4 in (282.8 and 285.4 px/in, mean 284.1)","method":"the outermost lines beside the frame 3.3 to 3.7 in below the top: 0.516 to 0.517 in each side of the middle, from 3.28 to 3.78 in below the top (.cache/batch5/b5-enhanced-sopmod-stock/fig3b.py)","via":"harvest"}}],"note":"B5's sheet: 'Remove the buttpad by squeezing the tabs firmly and applying pressure', and its drawing's label BUTTPAD RELEASE TABS. One each side of the web, ahead of the plate the pad sits on; the side photo gives their outline (3.30 to 3.79 in below the top, where the patent's front view has them: 3.28 to 3.78)."},"lock_pin_ahead_of_butt":{"label":"Lock pin ahead of the butt's rearmost point","kind":"length","measurements":[{"id":"photo","value":5.13,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/b5-enhanced-sopmod-stock 9bc66a9c7cdd (B5: SOP-1074_PROFILE_RIGHT.png, right side on a transparent ground, 2000 x 2000)","scaleRef":"the stock's own length and height, 1582 px for B5's 7.43 in and 1042 px for 4.93 in: 212.9 and 211.4 px/in, mean 212.2","method":"the pin's lower end is the block under the lever in the silhouette, columns 1257 to 1345 (0.41 in across, its foot 0.34 in below the lever's underside): its middle, column 1301, is 1092 px ahead of the pad's rearmost point (column 209) and 489 px (2.30 in) behind the front; ± is the two scales' spread and a pixel or two for the pin","via":"harvest"}}],"note":"The steel pin the adjustment lever draws out of the receiver extension's holes: its lower end, with a cross hole, hangs under the lever (B5's callout on its own picture: COLOR MATCHED STEEL HARDWARE; its sheet: 'Pull the adjustment lever down firmly until the stock can smoothly slide onto the buffer tube'). Where it stands says which hole the stock is on."},"butt_behind_pin_pos1":{"label":"Butt behind the takedown pin at position 1 (collapsed), on a carbine receiver extension","kind":"length","measurements":[{"id":"holes","value":9.309,"unit":"in","pm":0.08,"source":{"type":"derived","expr":"{bcm-receiver-extension.tube_front_behind_pin} + {bcm-receiver-extension.tube_length} - {bcm-receiver-extension.position_hole_rear_from_rear} - 5 * {bcm-receiver-extension.position_step} + {.lock_pin_ahead_of_butt}","via":"harvest"},"note":"The lock pin in the tube's front hole. ± for the hole's place (0.03), the tube's seat (0.02) and the pin's place in the stock (0.04), and for the tube's length, which is a generic figure."}],"note":"No photo on file shows the stock on a rifle square from the side, so it is seated by its lock pin in the tube's front hole: where the Army's drawings seat the tube and BCM's photo places its holes (bcm-stock-kit), and where the pin stands in the stock in B5's own side photo (the Bravo, B5's other stock on the same tube, is seated the same way from its own photo). That leaves the housing's front 0.21 in behind the castle nut (bcm-castle-nut.rear_face_behind_pin): the pin stands 2.30 in behind the front. B5 publishes no length of pull."},"lop_collapsed":{"label":"Length of pull, collapsed (the maker's reference rifle)","kind":"length","measurements":[],"note":"B5 publishes none (its page, its installation sheet and the sellers' pages read 2026-10-06)."},"lop_extended":{"label":"Length of pull, extended (the maker's reference rifle)","kind":"length","measurements":[],"note":"B5 publishes none."}}},{"subject":"b5-type-23-p-grip","title":"B5 Systems Type 23 P-Grip (P-GRIP 23, PGR-1122)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"b5","value":2.2,"unit":"oz","pm":0.005,"stated":"Weight: 2.20 oz","source":{"type":"spec","publisher":"manufacturer","name":"B5 Systems, P-GRIP 23: Features and specs (the page's text under its age overlay)","url":"https://b5systems.com/collection/ar/p-grip-23/","retrieved":"2026-10-19","via":"harvest"}},{"id":"b5-shop","value":2.4,"unit":"oz","pm":0.05,"stated":"Additional information Weight 2.4 oz","source":{"type":"spec","publisher":"manufacturer","name":"B5 Systems, P-GRIP 23: the shop's Additional information table, and its variation data (\"weight_html\":\"2.4 oz\" for each of the eight colours)","url":"https://b5systems.com/collection/ar/p-grip-23/","retrieved":"2026-10-19","via":"harvest"},"note":"The shop's own weight field, the same for every colour, the patterned ones too: what a shop keeps for shipping."}],"adopt":{"from":"b5","reason":"The figure in B5's own list of the grip's specifications, beside its sizes. The shop's field on the same page says 2.4 oz for every colour, as a shop's shipping weight does; it stays in view."},"note":"B5 doesn't say whether its figure takes in the T30 screw the grip comes with (the manual: \"Materials Provided - P-Grip 23, T30 Screw\")."},"length":{"label":"Length (B5's: the heel to the block's front face, the flat top level)","kind":"length","measurements":[{"id":"b5","value":2.73,"unit":"in","stated":"Length: 2.73 in","source":{"type":"spec","publisher":"manufacturer","name":"B5 Systems, P-GRIP 23: Features and specs (the page's text under its age overlay)","url":"https://b5systems.com/collection/ar/p-grip-23/","retrieved":"2026-10-19","via":"harvest"}}],"note":"B5 doesn't say between what. On B5's two side pictures with the flat top level the silhouette's horizontal extent and its height are 2.73 and 4.84 in at one scale (0.24% apart on the right side, 0.6% on the left): the heel at the back strap's foot to the block's front face."},"height":{"label":"Height (B5's: the beavertail's top to the toe, the flat top level)","kind":"length","measurements":[{"id":"b5","value":4.84,"unit":"in","stated":"Height: 4.84 in","source":{"type":"spec","publisher":"manufacturer","name":"B5 Systems, P-GRIP 23: Features and specs (the page's text under its age overlay)","url":"https://b5systems.com/collection/ar/p-grip-23/","retrieved":"2026-10-19","via":"harvest"}}],"note":"As length: the silhouette's vertical extent on B5's side pictures, the flat top level."},"thickness":{"label":"Thickness (side to side; B5's \"Width\")","kind":"length","measurements":[{"id":"b5","value":1.26,"unit":"in","stated":"Width: 1.26 in","source":{"type":"spec","publisher":"manufacturer","name":"B5 Systems, P-GRIP 23: Features and specs (the page's text under its age overlay)","url":"https://b5systems.com/collection/ar/p-grip-23/","retrieved":"2026-10-19","via":"harvest"}}],"note":"No view on file is square to the grip's front, back or base, so where down the grip it is this wide isn't seen: drawn as the body's width from the shoulder under the block to the base."},"grip_angle":{"label":"Grip angle (the straps' lean from vertical, installed)","kind":"angle","measurements":[{"id":"b5","value":13,"unit":"deg","stated":"13° Angle For Improved Ergonomics","source":{"type":"spec","publisher":"manufacturer","name":"B5 Systems, P-GRIP 23: Features and specs (the page's text under its age overlay)","url":"https://b5systems.com/collection/ar/p-grip-23/","retrieved":"2026-10-19","via":"harvest"}},{"id":"front-strap","value":13.251,"unit":"deg","source":{"type":"derived","expr":"{.front_strap_lean}","via":"harvest"},"note":"The front strap's lean read on B5's right side picture with its flat top level."}],"adopt":{"from":"b5","reason":"B5's own figure, and the front strap's lean on its own pictures with the flat top level agrees with it."},"note":"B5's figure is the front strap's lean with the flat top level (front_strap_lean, on B5's own two pictures). The back strap leans more (back_strap_lean): the grip narrows toward its base. The catalog's other grips give the mean of the two straps; this one's mean is about 16."},"front_strap_lean":{"label":"Front strap's lean from the vertical, the flat top level","kind":"angle","measurements":[{"id":"photo","value":13.251,"unit":"deg","pm":0.527,"source":{"type":"photo","photo":"references/b5-type-23-p-grip 0e18f2708bff (B5's PGR-1122_PROFILE_RIGHT (2024/12): the black grip's right side square on, its flat top level, 1400 x 1400 on a transparent ground)","scaleRef":"scale from b5-type-23-p-grip.height = 4.84 in (y-extent 995 px → 205.6 px/in) and b5-type-23-p-grip.length = 2.73 in (x-extent 563 px → 206.2 px/in), which agree within 0.3%; mean 205.9 px/in","method":"angle from the vertical of the straight line through the outline in x [0.3, 1.1] in y [-3.7, -1.8] (1.94 in of it, rms 0.005) of the traced outline (tools/trace.py); the front strap's lean from the vertical with the flat top level: the straight line through the outline's front edge below the tang","via":"harvest"}},{"id":"photo-left","value":13.034,"unit":"deg","pm":0.577,"source":{"type":"photo","photo":"references/b5-type-23-p-grip ad03888ce47f (B5's PGR-1122_PROFILE_LEFT: the black grip's left side square on, its flat top level)","scaleRef":"scale from b5-type-23-p-grip.height = 4.84 in (y-extent 997 px → 206.0 px/in) and b5-type-23-p-grip.length = 2.73 in (x-extent 561 px → 205.5 px/in), which agree within 0.2%; mean 205.7 px/in","method":"angle from the vertical of the straight line through the outline in x [0.3, 1.1] in y [-3.7, -1.8] (1.93 in of it, rms 0.006) of the traced outline (tools/trace.py); as on the right side","via":"harvest"}}],"adopt":{"from":"photo","reason":"B5's right side picture, which the side outline is traced from; its left side picture reads 13.03, within both readings' ±, and B5 says 13 (grip_angle)."}},"back_strap_lean":{"label":"Back strap's lean from the vertical, the flat top level","kind":"angle","measurements":[{"id":"photo","value":18.947,"unit":"deg","pm":0.424,"source":{"type":"photo","photo":"references/b5-type-23-p-grip 0e18f2708bff (B5's PGR-1122_PROFILE_RIGHT (2024/12): the black grip's right side square on, its flat top level, 1400 x 1400 on a transparent ground)","scaleRef":"scale from b5-type-23-p-grip.height = 4.84 in (y-extent 995 px → 205.6 px/in) and b5-type-23-p-grip.length = 2.73 in (x-extent 563 px → 206.2 px/in), which agree within 0.3%; mean 205.9 px/in","method":"angle from the vertical of the straight line through the outline in x [-1.6, -0.5] in y [-3.6, -1.5] (2.22 in of it, rms 0.004) of the traced outline (tools/trace.py); the back strap's lean from the vertical with the flat top level: the straight line through the outline's rear edge below the beavertail","via":"harvest"}},{"id":"photo-left","value":18.754,"unit":"deg","pm":0.43,"source":{"type":"photo","photo":"references/b5-type-23-p-grip ad03888ce47f (B5's PGR-1122_PROFILE_LEFT: the black grip's left side square on, its flat top level)","scaleRef":"scale from b5-type-23-p-grip.height = 4.84 in (y-extent 997 px → 206.0 px/in) and b5-type-23-p-grip.length = 2.73 in (x-extent 561 px → 205.5 px/in), which agree within 0.2%; mean 205.7 px/in","method":"angle from the vertical of the straight line through the outline in x [-1.6, -0.5] in y [-3.6, -1.5] (2.21 in of it, rms 0.004) of the traced outline (tools/trace.py); as on the right side","via":"harvest"}}],"adopt":{"from":"photo","reason":"B5's right side picture, which the side outline is traced from; its left side picture reads 18.75, within both readings' ±."}},"bottom_below_lower_underside":{"label":"Grip bottom below the receiver's underside where the grip bears","kind":"length","measurements":[{"id":"photo","value":4.138,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/b5-type-23-p-grip 0e18f2708bff (B5's PGR-1122_PROFILE_RIGHT (2024/12): the black grip's right side square on, its flat top level, 1400 x 1400 on a transparent ground)","scaleRef":"scale from b5-type-23-p-grip.height = 4.84 in (y-extent 995 px → 205.6 px/in) and b5-type-23-p-grip.length = 2.73 in (x-extent 563 px → 206.2 px/in), which agree within 0.3%; mean 205.9 px/in","method":"−y_min of the traced outline (tools/trace.py); the toe below the flat top, which bears on the receiver's underside: the traced outline's lowest point, the picture's flat top level as shot","via":"harvest"}},{"id":"photo-left","value":4.161,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/b5-type-23-p-grip ad03888ce47f (B5's PGR-1122_PROFILE_LEFT: the black grip's left side square on, its flat top level)","scaleRef":"scale from b5-type-23-p-grip.height = 4.84 in (y-extent 997 px → 206.0 px/in) and b5-type-23-p-grip.length = 2.73 in (x-extent 561 px → 205.5 px/in), which agree within 0.2%; mean 205.7 px/in","method":"−y_min of the traced outline (tools/trace.py); as on the right side","via":"harvest"}}],"adopt":{"from":"photo","reason":"B5's right side picture, which the side outline is traced from; its left side picture reads 0.023 deeper, within the two readings' ± together (each is B5's two figures at one scale on its own picture)."},"note":"The toe below the flat top, on B5's side pictures scaled by B5's length and height. No picture of the grip on a lower with the pins in view was found."},"toe_y":{"label":"Toe (the grip's lowest point), Y in the grip frame","kind":"length","measurements":[{"id":"derived","value":-4.138,"unit":"in","source":{"type":"derived","expr":"-{.bottom_below_lower_underside}","via":"harvest"}}]},"block_front_x":{"label":"The block's front face, ahead of the flat top's rear end","kind":"length","measurements":[{"id":"photo","value":1.241,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/b5-type-23-p-grip 0e18f2708bff (B5's PGR-1122_PROFILE_RIGHT (2024/12): the black grip's right side square on, its flat top level, 1400 x 1400 on a transparent ground)","scaleRef":"scale from b5-type-23-p-grip.height = 4.84 in (y-extent 995 px → 205.6 px/in) and b5-type-23-p-grip.length = 2.73 in (x-extent 563 px → 206.2 px/in), which agree within 0.3%; mean 205.9 px/in","method":"x_max in y [-1.2, -0.1] of the traced outline (tools/trace.py); the block's front face ahead of the flat top's rear end: the outline's foremost point between the rounded corner above and the tang's foot below (one straight face, 1.3 in deep)","via":"harvest"}},{"id":"photo-left","value":1.237,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/b5-type-23-p-grip ad03888ce47f (B5's PGR-1122_PROFILE_LEFT: the black grip's left side square on, its flat top level)","scaleRef":"scale from b5-type-23-p-grip.height = 4.84 in (y-extent 997 px → 206.0 px/in) and b5-type-23-p-grip.length = 2.73 in (x-extent 561 px → 205.5 px/in), which agree within 0.2%; mean 205.7 px/in","method":"x_max in y [-1.2, -0.1] of the traced outline (tools/trace.py); as on the right side","via":"harvest"}}],"adopt":{"from":"photo","reason":"B5's right side picture, which the side outline is traced from; its left reads the same within 0.004."}},"beavertail_rear_x":{"label":"The beavertail's rearmost point, behind the flat top's rear end","kind":"length","measurements":[{"id":"photo","value":1.042,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/b5-type-23-p-grip 0e18f2708bff (B5's PGR-1122_PROFILE_RIGHT (2024/12): the black grip's right side square on, its flat top level, 1400 x 1400 on a transparent ground)","scaleRef":"scale from b5-type-23-p-grip.height = 4.84 in (y-extent 995 px → 205.6 px/in) and b5-type-23-p-grip.length = 2.73 in (x-extent 563 px → 206.2 px/in), which agree within 0.3%; mean 205.9 px/in","method":"−x_min in y [0.05, 1.0] of the traced outline (tools/trace.py); the beavertail's rearmost point behind the flat top's rear end","via":"harvest"}}]},"seat_x":{"label":"Seat, X: where the grip's frame origin (its flat top's rear end) sits ahead of the takedown pin, installed","kind":"length","measurements":[{"id":"interface","value":-0.066,"unit":"in","source":{"type":"derived","expr":"{std.ar15.receiver_rear_x} + {std.ar15.grip_lug_front_from_rear_face} - {.block_front_x}","via":"harvest"},"note":"The block's front face (block_front_x, on the traced side) at the ears' rear face."}],"note":"Seated by its interface, as BCM's Mod 3 is: the block's front face against the rear face of the trigger guard's ears, where the Army drawing ends the lug (std.ar15.grip_lug_front_from_rear_face from the receiver's rear face). B5's manual draws the grip slid up onto the lower with its block's front face meeting the ears (FIG 2); no picture of it installed with the pins in view was found to read it on."},"top_block_width":{"label":"Top block (the two walls that sit under the receiver) and the beavertail, across","kind":"length","measurements":[{"id":"assumed","value":0.88,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the block flush with the receiver's side (std.ar15.lower_body_width, the Army drawing's 0.88), as B5's installation drawing (FIG 2) has it. ± is a step of 0.02 in a side.","via":"harvest"}}],"note":"No view on file is square to the grip's top, front or back. B5's manual draws the block's walls rising into the receiver's sides in one line (FIG 2), as the catalog's other grips' blocks are: taken as the receiver's width."},"lug_slot_width":{"label":"The slot in the top that goes over the receiver's lug, across","kind":"length","measurements":[{"id":"assumed","value":0.405,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file looks square at the grip's top. Between the two grips on file whose slot is read (BCM's Mod 3 0.385, Magpul's MOE-K2+ 0.425), so that the lug, the Army drawing's .375, stands clear in it.","via":"harvest"}}],"note":"No view on file looks at the top square (Rifle Supply's two photos see the top from behind and above, nearly edge on, and show an earlier moulding: two walls with webs between). Drawn between the two grips on file that have it read: BCM's Mod 3, 0.385, and Magpul's MOE-K2+, 0.425."},"shoulder_length":{"label":"The shoulder under the block: how far down the strap the grip widens from the block's width to the body's","kind":"length","measurements":[{"id":"assumed","value":0.4,"unit":"in","pm":0.2,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file is square to the grip's back or front. Ending at the texture panel's top, where B5's pictures have the side flat.","via":"harvest"}}]},"back_strap_round":{"label":"The back strap's corners in section, their radius","kind":"length","measurements":[{"id":"assumed","value":0.45,"unit":"in","pm":0.15,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file is square to a section. Rifle Supply's photo from behind and the left has the back strap round across, nearly a half circle of the body's width.","via":"harvest"}}]},"front_strap_round":{"label":"The front strap's corners in section, their radius","kind":"length","measurements":[{"id":"assumed","value":0.25,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file is square to a section. Sportsman's photo from ahead and the right has the front strap flatter than the back, its band of texture turning onto the side round a corner where the groove runs.","via":"harvest"}}]},"groove_width":{"label":"The grooves round the texture panel and beside the front strap's band, across","kind":"length","measurements":[{"id":"photo","value":0.039,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/b5-type-23-p-grip 0e18f2708bff (B5's PGR-1122_PROFILE_RIGHT, 1400 x 1400)","scaleRef":"B5's length and height (205.6 px to the inch)","method":"the strap groove's dark line, 4 px across on a gridded crop (.cache/batch14/b5-type-23-p-grip/grid-panel.png), taken as its shadowed wall: twice that. ± is a pixel each side.","via":"harvest"}}],"note":"The strap's groove is a dark line 4 px wide on B5's right side picture at 205.6 px to the inch, 0.019 in: a groove lit from one side is its lit wall beside its shadowed one, and as wide as both (CLAUDE.md, the 22RB's grooves)."},"groove_depth":{"label":"The grooves' depth","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows a groove in profile.","via":"harvest"}}]}}},{"subject":"bad-workhorse-lower","title":"Battle Arms Development Workhorse stripped lower (WH556-LR)","dimensions":{"weight":{"label":"Weight, stripped","kind":"mass","measurements":[{"id":"spec","value":8.22,"unit":"oz","stated":"Weight: 8.22 oz","source":{"type":"spec","publisher":"manufacturer","name":"Battle Arms Development","url":"https://battlearmsdevelopment.com/shop/wh556-lr-blk-workhorse-forged-7075-t6-lower-receiver-stripped-black-anodized-ar15-956","retrieved":"2026-09-30","via":"harvest"}},{"id":"retailer","value":8.1,"unit":"oz","stated":"Weight: 8.1 oz","source":{"type":"spec","publisher":"retailer","name":"R1 Tactical","url":"https://redcon1tactical.com/battle-arms-development-ar-15-workhorse-forged-lower-receiver.html","retrieved":"2026-09-30","via":"harvest"}}],"adopt":{"from":"spec","reason":"Manufacturer figure, repeated by most retailers."}},"buffer_axis_above_pin":{"label":"Buffer tube (bore) axis above takedown pin center","kind":"length","measurements":[{"id":"magpul-photo","value":0.849,"unit":"in","source":{"type":"photo","photo":"Magpul side product photo (not yet archived)","scaleRef":"not recorded in brief","method":"calibrated photo measurement; details not recorded in brief","via":"brief"},"note":"The Workhorse photo agrees within 0.05 in (brief). The buffer tube is coaxial with the bore."},{"id":"std","value":0.8775,"unit":"in","pm":0.0015,"source":{"type":"derived","expr":"{std.ar15.bore_axis_y}","via":"user"},"note":"A forged mil-spec lower: the threaded hole's centre is the drawing's (.629 above the deck, the deck .250 above the pins)."}],"adopt":{"from":"std","reason":"The Army's drawings of the lower and of the upper give the same height (M6). M2's photo reads 0.03 low, and so do this lower's own photos (tower_top_above_pin): the mid-plane, scaled by the pins' near ends 0.44 in nearer the lens, reads about 2% short of what stands above the picture's centre."}},"magwell_bottom_center_x":{"label":"Magwell bottom opening center, X","kind":"length","measurements":[{"id":"photo","value":4.72,"unit":"in","stated":"about (4.72, −2.07) in the rifle frame","source":{"type":"photo","photo":"not recorded in brief","scaleRef":"not recorded in brief","method":"calibrated photo measurement","via":"brief"}}]},"magwell_bottom_center_y":{"label":"Magwell bottom opening center, Y","kind":"length","measurements":[{"id":"photo","value":-2.07,"unit":"in","stated":"about (4.72, −2.07) in the rifle frame","source":{"type":"photo","photo":"not recorded in brief","scaleRef":"not recorded in brief","method":"calibrated photo measurement","via":"brief"}},{"id":"right","value":-2.144,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"rifle frame from reviewed holes takedown (371.5,502.5) r=20px, pivot (1380.5,505.5) r=20px = takedown(0.0, 0.0), pivot(6.375, 0.0) (158.3 px/in)","method":"silhouette y_min in x [4.7, 4.74] in frame coordinates; ± from hole-center and edge error","via":"harvest"},"note":"Outer silhouette of the magwell lip at the brief's x = 4.72."},{"id":"left","value":-2.16,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"rifle frame from reviewed holes takedown (1242.5,489.5) r=21px, pivot (223.5,488.5) r=22px = takedown(0.0, 0.0), pivot(6.375, 0.0) (159.8 px/in)","method":"silhouette y_min in x [4.7, 4.74] in frame coordinates; ± from hole-center and edge error","via":"harvest"},"note":"Outer silhouette of the magwell lip at the brief's x = 4.72."}],"adopt":{"from":"photo","reason":"The brief's value pairs with its measured magazine hang (2.4 in below this edge). Both harvested photos read the outer lip lower and steeper, which may be a different reference line."}},"magwell_bottom_angle":{"label":"Magwell bottom edge rise toward the front","kind":"angle","measurements":[{"id":"photo","value":5.5,"unit":"deg","stated":"rises toward the front by about 5.5°","source":{"type":"photo","photo":"not recorded in brief","scaleRef":"not recorded in brief","method":"calibrated photo measurement","via":"brief"}},{"id":"right","value":9.85,"unit":"deg","pm":0.54,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"rifle frame from reviewed holes takedown (371.5,502.5) r=20px, pivot (1380.5,505.5) r=20px = takedown(0.0, 0.0), pivot(6.375, 0.0) (158.3 px/in)","method":"bottom-edge slope between x = 4.0 and 6.0 in (frame)","via":"harvest"},"note":"Outer silhouette of the magwell lip; the brief's 5.5° may be measured on the opening plane instead."},{"id":"left","value":9.53,"unit":"deg","pm":0.54,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"rifle frame from reviewed holes takedown (1242.5,489.5) r=21px, pivot (223.5,488.5) r=22px = takedown(0.0, 0.0), pivot(6.375, 0.0) (159.8 px/in)","method":"bottom-edge slope between x = 4.0 and 6.0 in (frame)","via":"harvest"},"note":"Outer silhouette of the magwell lip; the brief's 5.5° may be measured on the opening plane instead."}],"adopt":{"from":"photo","reason":"The brief's value pairs with its measured magazine hang (2.4 in below this edge). Both harvested photos read the outer lip lower and steeper, which may be a different reference line."}},"trigger_guard_front_x":{"label":"Trigger guard front ear hole, X","kind":"length","measurements":[{"id":"tdp","value":3.3425,"unit":"in","source":{"type":"derived","expr":"{std.ar15.trigger_guard_front_x}","via":"user"},"note":"The Workhorse is a TDP-compatible forging, so its hole is the standard's."},{"id":"right","value":3.318,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bad-workhorse-lower/03-3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo, 1600px)","scaleRef":"takedown→pivot pin holes = 6.375 in (standard), 158.4 px/in","method":"Hough-circle hole centers; Umeyama similarity to the rifle frame (takedown at origin); ± is ~2 px","calibration":"none (inline)","via":"harvest"}},{"id":"trace-right-holes","value":3.337,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"a pinhole camera fitted to the rims of 7 holes, 5 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer at the ledger's places; selector (its y left to the fit), guard_rear (its x and y left to the fit), guard_front (tied to guard_rear)): lens 24.0 ± 0.8 in from the centre plane, standing over x 4.17, y -1.77, the side leaning 7.1 ± 1.2° to the sensor with its bottom nearer and 0.1° with the picture's right nearer; 158.8 px/in on the near face at the lens's foot; rims within 0.76 px rms","method":"x of the hole guard_front (guard_rear's, fitted with the camera, and the step to it: the rims' ± through the fit) of the traced outline (tools/trace.py)","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The published standard (TDP 8448608). A camera fitted to the right photo (2026-10-05) with the guard's two holes left to the fit, this one 1.844 ahead of the rear as the drawing has them, reads it 3.337: 0.006 behind, inside both ±. The two-pin frame's 3.318 was 0.025 behind by the frame: see trigger_guard_rear_x."},"note":"External ear hole ahead of the trigger opening, on the right side: the left ear shows no hole (M1b's left reading, 3.325, was the ear face). Re-checked on a 3× crop in M3 (3.317)."},"trigger_guard_front_y":{"label":"Trigger guard front ear hole, Y","kind":"length","measurements":[{"id":"right","value":-2.222,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bad-workhorse-lower/03-3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo, 1600px)","scaleRef":"takedown→pivot pin holes = 6.375 in (standard), 158.4 px/in","method":"Hough-circle hole centers; Umeyama similarity to the rifle frame (takedown at origin); ± is ~2 px","calibration":"none (inline)","via":"harvest"}},{"id":"tdp","value":-2.18,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{std.ar15.trigger_guard_rear_y}","via":"user"},"note":"The drawing's side elevation has the guard's two holes on one centre line, 2.18 below the line through the pins; the reference CAD model has this one at Y -2.179."}],"adopt":{"from":"tdp","reason":"The Army's drawing: on the rear hole's line. The right photo's -2.222 is the two-pin frame's, 0.04 low by the frame (see trigger_guard_rear_y); until 2026-10-05 it stood alone, and a trigger guard pinned into the two holes hung 1.3 degrees nose down."},"note":"Frame Y (up). Right side only (see trigger_guard_front_x)."},"trigger_guard_rear_x":{"label":"Trigger guard rear ear hole, X","kind":"length","measurements":[{"id":"tdp","value":1.4985,"unit":"in","source":{"type":"derived","expr":"{std.ar15.trigger_guard_rear_x}","via":"user"},"note":"The Workhorse is a TDP-compatible forging, so its hole is the standard's."},{"id":"right","value":1.469,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo, 1600px)","scaleRef":"pin frame (takedown→pivot = 6.375 in, Hough-refined), 158.3 px/in","method":"centre of the hole's dark rim (603, 852) px, picked on a 3× gridded crop (Hough moves ±5 px across windows on a ~20 px hole)","via":"harvest"}},{"id":"left","value":1.459,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo, 1600px)","scaleRef":"pin frame (takedown→pivot = 6.375 in, Hough-refined, mirrored), 159.8 px/in","method":"centre of the hole's dark rim (1009, 842) px, picked on a 3× gridded crop (Hough moves ±5 px across windows on a ~20 px hole)","via":"harvest"}},{"id":"trace-right-holes","value":1.493,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"a pinhole camera fitted to the rims of 7 holes, 5 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer at the ledger's places; selector (its y left to the fit), guard_rear (its x and y left to the fit), guard_front (tied to guard_rear)): lens 24.0 ± 0.8 in from the centre plane, standing over x 4.17, y -1.77, the side leaning 7.1 ± 1.2° to the sensor with its bottom nearer and 0.1° with the picture's right nearer; 158.8 px/in on the near face at the lens's foot; rims within 0.76 px rms","method":"x of the hole guard_rear (fitted with the camera: the rims' ± through the fit) of the traced outline (tools/trace.py)","via":"harvest"}},{"id":"trace-left-holes","value":1.494,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"a pinhole camera fitted to the rims of 6 holes, 4 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer at the ledger's places; selector (its y left to the fit), guard_rear (its x and y left to the fit)): lens 23.9 ± 0.8 in from the centre plane, standing over x 3.83, y -2.09, the side leaning 8.7 ± 2.3° to the sensor with its bottom nearer and 0.9° with the picture's left nearer; 160.1 px/in on the near face at the lens's foot; rims within 0.70 px rms","method":"x of the hole guard_rear (fitted with the camera: the rims' ± through the fit) of the traced outline (tools/trace.py)","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The published standard (TDP 8448608). Through a camera fitted to each photo with this hole's place left to the fit (2026-10-05) it reads 1.493 and 1.494: 0.005 behind the drawing's, inside both ±. The two-pin frames' 1.469 and 1.459 were 0.03 to 0.04 behind, and that was the frame, not the part: two pins on one line fix one scale along it, and both photos were taken from 24 in with the receiver leaning 9 degrees to the sensor, its bottom nearer. The picture is 1.5% larger 2.2 in below the pins than on their line, about the point the lens stands over (4 in ahead of the takedown pin, level with the guard): this hole, 2.7 in behind that point, reads 0.04 further from it, less 0.01 for its rim being 0.11 in further from the lens than the pins' rims."},"note":"M1b's Hough fit (1.589 / 1.572) had locked onto the ear's face ~0.12 in ahead of the hole in both photos; found in M3 when the MOE guard didn't match the user's installed photos. The real rear hole is the ~0.13 in roll-pin hole (a published 0.1275 in)."},"trigger_guard_rear_y":{"label":"Trigger guard rear ear hole, Y","kind":"length","measurements":[{"id":"tdp","value":-2.18,"unit":"in","source":{"type":"derived","expr":"{std.ar15.trigger_guard_rear_y}","via":"user"},"note":"The Workhorse is a TDP-compatible forging, so its hole is the standard's."},{"id":"right","value":-2.204,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo, 1600px)","scaleRef":"pin frame (takedown→pivot = 6.375 in, Hough-refined), 158.3 px/in","method":"centre of the hole's dark rim (603, 852) px, picked on a 3× gridded crop (Hough moves ±5 px across windows on a ~20 px hole)","via":"harvest"}},{"id":"left","value":-2.207,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo, 1600px)","scaleRef":"pin frame (takedown→pivot = 6.375 in, Hough-refined, mirrored), 159.8 px/in","method":"centre of the hole's dark rim (1009, 842) px, picked on a 3× gridded crop (Hough moves ±5 px across windows on a ~20 px hole)","via":"harvest"}},{"id":"trace-right-holes","value":-2.194,"unit":"in","pm":0.007,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"a pinhole camera fitted to the rims of 7 holes, 5 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer at the ledger's places; selector (its y left to the fit), guard_rear (its x and y left to the fit), guard_front (tied to guard_rear)): lens 24.0 ± 0.8 in from the centre plane, standing over x 4.17, y -1.77, the side leaning 7.1 ± 1.2° to the sensor with its bottom nearer and 0.1° with the picture's right nearer; 158.8 px/in on the near face at the lens's foot; rims within 0.76 px rms","method":"y of the hole guard_rear (fitted with the camera: the rims' ± through the fit) of the traced outline (tools/trace.py)","via":"harvest"}},{"id":"trace-left-holes","value":-2.192,"unit":"in","pm":0.013,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"a pinhole camera fitted to the rims of 6 holes, 4 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer at the ledger's places; selector (its y left to the fit), guard_rear (its x and y left to the fit)): lens 23.9 ± 0.8 in from the centre plane, standing over x 3.83, y -2.09, the side leaning 8.7 ± 2.3° to the sensor with its bottom nearer and 0.9° with the picture's left nearer; 160.1 px/in on the near face at the lens's foot; rims within 0.70 px rms","method":"y of the hole guard_rear (fitted with the camera: the rims' ± through the fit) of the traced outline (tools/trace.py)","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The published standard (TDP 8448608: 2.18, two places). Through the cameras, with its place left to the fit, the two photos read it -2.194 ± 0.007 and -2.192 ± 0.013: 0.013 below the drawing's, at the edge of its ± and inside theirs. Those fits lean 7.1 ± 1.2 and 8.7 ± 2.3 degrees; with every hole at the drawing's place the fits lean 9.3 and 10.6, as well within the rims' ±: whether that last hundredth is the part's or the lean's the photos can't say. The two-pin frames' -2.204 and -2.207 were low by the frame: 1.5% of 2.18 in is 0.03."},"note":"Frame Y (up). See trigger_guard_rear_x."},"trigger_pin_x":{"label":"Trigger pin hole center (external), X","kind":"length","measurements":[{"id":"tdp","value":1.928,"unit":"in","source":{"type":"derived","expr":"{std.ar15.trigger_pin_x}","via":"user"},"note":"The Workhorse is a TDP-compatible forging, so its hole is the standard's."},{"id":"right","value":1.914,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bad-workhorse-lower/03-3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo, 1600px)","scaleRef":"takedown→pivot pin holes = 6.375 in (standard), 158.4 px/in","method":"Hough-circle hole centers; Umeyama similarity to the rifle frame (takedown at origin); ± is ~2 px","calibration":"none (inline)","via":"harvest"}},{"id":"left","value":1.916,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bad-workhorse-lower/02-6d4ee1a1b3b8 (left side, independent photo, 1600px)","scaleRef":"takedown→pivot pin holes = 6.375 in (standard), 159.7 px/in","method":"Hough-circle hole centers, mirrored view; Umeyama similarity to the rifle frame; ± is ~2 px","calibration":"none (inline)","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The published standard (TDP 8448608), and since 2026-10-05 one of the holes each photo's camera is fitted to: its rim lies within a pixel of where the camera puts the drawing's. The two-pin frames' 1.914 and 1.916 were 0.013 behind by the frame (see trigger_guard_rear_x; on the right its origin also stood on the takedown hole's rim, the floor of a spotface 0.04 in below the face, which reads 0.007 toward the lens)."},"note":"The lower, rearward of the two fire-control pin holes (the trigger tail sits against the selector). External hole position only."},"trigger_pin_y":{"label":"Trigger pin hole center (external), Y","kind":"length","measurements":[{"id":"right","value":-0.678,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bad-workhorse-lower/03-3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo, 1600px)","scaleRef":"takedown→pivot pin holes = 6.375 in (standard), 158.4 px/in","method":"Hough-circle hole centers; Umeyama similarity to the rifle frame (takedown at origin); ± is ~2 px","calibration":"none (inline)","via":"harvest"}},{"id":"left","value":-0.689,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bad-workhorse-lower/02-6d4ee1a1b3b8 (left side, independent photo, 1600px)","scaleRef":"takedown→pivot pin holes = 6.375 in (standard), 159.7 px/in","method":"Hough-circle hole centers, mirrored view; Umeyama similarity to the rifle frame; ± is ~2 px","calibration":"none (inline)","via":"harvest"}},{"id":"tdp","value":-0.689,"unit":"in","source":{"type":"derived","expr":"{std.ar15.trigger_pin_y}","via":"user"},"note":"The Workhorse is a TDP-compatible forging, so its hole is the standard's."}],"adopt":{"from":"tdp","reason":"The drawing dimensions it (2026-10-03: .375 and .3140 below the pin line); the left photo reads the same, the right 0.011 high. Until then the right photo's, for its cleaner hole edges."},"note":"Frame Y (up)."},"hammer_pin_x":{"label":"Hammer pin hole center (external), X","kind":"length","measurements":[{"id":"tdp","value":2.771,"unit":"in","source":{"type":"derived","expr":"{std.ar15.hammer_pin_x}","via":"user"},"note":"The Workhorse is a TDP-compatible forging, so its hole is the standard's."},{"id":"right","value":2.753,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bad-workhorse-lower/03-3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo, 1600px)","scaleRef":"takedown→pivot pin holes = 6.375 in (standard), 158.4 px/in","method":"Hough-circle hole centers; Umeyama similarity to the rifle frame (takedown at origin); ± is ~2 px","calibration":"none (inline)","via":"harvest"}},{"id":"left","value":2.768,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bad-workhorse-lower/02-6d4ee1a1b3b8 (left side, independent photo, 1600px)","scaleRef":"takedown→pivot pin holes = 6.375 in (standard), 159.7 px/in","method":"Hough-circle hole centers, mirrored view; Umeyama similarity to the rifle frame; ± is ~2 px","calibration":"none (inline)","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The published standard (TDP 8448608), and since 2026-10-05 one of the holes each photo's camera is fitted to: its rim lies within a pixel of where the camera puts the drawing's. The two-pin frames read 2.753 and 2.768: by the frame (see trigger_pin_x)."},"note":"The upper, forward fire-control pin hole. External hole position only."},"hammer_pin_y":{"label":"Hammer pin hole center (external), Y","kind":"length","measurements":[{"id":"right","value":-0.361,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bad-workhorse-lower/03-3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo, 1600px)","scaleRef":"takedown→pivot pin holes = 6.375 in (standard), 158.4 px/in","method":"Hough-circle hole centers; Umeyama similarity to the rifle frame (takedown at origin); ± is ~2 px","calibration":"none (inline)","via":"harvest"}},{"id":"left","value":-0.376,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bad-workhorse-lower/02-6d4ee1a1b3b8 (left side, independent photo, 1600px)","scaleRef":"takedown→pivot pin holes = 6.375 in (standard), 159.7 px/in","method":"Hough-circle hole centers, mirrored view; Umeyama similarity to the rifle frame; ± is ~2 px","calibration":"none (inline)","via":"harvest"}},{"id":"tdp","value":-0.375,"unit":"in","source":{"type":"derived","expr":"{std.ar15.hammer_pin_y}","via":"user"},"note":"The Workhorse is a TDP-compatible forging, so its hole is the standard's."}],"adopt":{"from":"tdp","reason":"The drawing dimensions it (2026-10-03: .375 below the pin line); the left photo reads the same, the right 0.014 high. Until then the right photo's, for its cleaner hole edges."},"note":"Frame Y (up)."},"selector_x":{"label":"Safety selector hole center, X","kind":"length","measurements":[{"id":"tdp","value":0.803,"unit":"in","source":{"type":"derived","expr":"{std.ar15.selector_x}","via":"user"},"note":"The Workhorse is a TDP-compatible forging, so its hole is the standard's."},{"id":"right","value":0.79,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bad-workhorse-lower/03-3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo, 1600px)","scaleRef":"takedown→pivot pin holes = 6.375 in (standard), 158.4 px/in","method":"Hough-circle hole centers; Umeyama similarity to the rifle frame (takedown at origin); ± is ~2 px","calibration":"none (inline)","via":"harvest"}},{"id":"left","value":0.789,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bad-workhorse-lower/02-6d4ee1a1b3b8 (left side, independent photo, 1600px)","scaleRef":"takedown→pivot pin holes = 6.375 in (standard), 159.7 px/in","method":"Hough-circle hole centers, mirrored view; Umeyama similarity to the rifle frame; ± is ~2 px","calibration":"none (inline)","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The published standard (TDP 8448608), and since 2026-10-05 one of the holes each photo's camera is fitted to: its rim lies within a pixel of where the camera puts the drawing's. The two-pin frames' 0.790 and 0.789 were 0.013 behind by the frame (see trigger_pin_x)."},"note":"Places the LPK selector."},"selector_y":{"label":"Safety selector hole center, Y","kind":"length","measurements":[{"id":"right","value":-0.466,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bad-workhorse-lower/03-3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo, 1600px)","scaleRef":"takedown→pivot pin holes = 6.375 in (standard), 158.4 px/in","method":"Hough-circle hole centers; Umeyama similarity to the rifle frame (takedown at origin); ± is ~2 px","calibration":"none (inline)","via":"harvest"}},{"id":"left","value":-0.457,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bad-workhorse-lower/02-6d4ee1a1b3b8 (left side, independent photo, 1600px)","scaleRef":"takedown→pivot pin holes = 6.375 in (standard), 159.7 px/in","method":"Hough-circle hole centers, mirrored view; Umeyama similarity to the rifle frame; ± is ~2 px","calibration":"none (inline)","via":"harvest"}},{"id":"trace-right-holes","value":-0.466,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"a pinhole camera fitted to the rims of 7 holes, 5 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer at the ledger's places; selector (its y left to the fit), guard_rear (its x and y left to the fit), guard_front (tied to guard_rear)): lens 24.0 ± 0.8 in from the centre plane, standing over x 4.17, y -1.77, the side leaning 7.1 ± 1.2° to the sensor with its bottom nearer and 0.1° with the picture's right nearer; 158.8 px/in on the near face at the lens's foot; rims within 0.76 px rms","method":"y of the hole selector (fitted with the camera: the rims' ± through the fit) of the traced outline (tools/trace.py)","via":"harvest"}},{"id":"trace-left-holes","value":-0.464,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"a pinhole camera fitted to the rims of 6 holes, 4 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer at the ledger's places; selector (its y left to the fit), guard_rear (its x and y left to the fit)): lens 23.9 ± 0.8 in from the centre plane, standing over x 3.83, y -2.09, the side leaning 8.7 ± 2.3° to the sensor with its bottom nearer and 0.9° with the picture's left nearer; 160.1 px/in on the near face at the lens's foot; rims within 0.70 px rms","method":"y of the hole selector (fitted with the camera: the rims' ± through the fit) of the traced outline (tools/trace.py)","via":"harvest"}}],"adopt":{"from":"trace-right-holes","reason":"Read through the camera fitted to each photo (2026-10-05), its height the one coordinate of the fire-control holes left to the fit: -0.466 and -0.464. The two-pin frames read -0.466 and -0.457."},"note":"Frame Y (up)."},"rear_behind_pin":{"label":"Rear of the buffer-tower ring behind the takedown pin","kind":"length","measurements":[{"id":"right","value":1.162,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"rifle frame from reviewed holes takedown (371.5,502.5) r=20px, pivot (1380.5,505.5) r=20px = takedown(0.0, 0.0), pivot(6.375, 0.0) (158.3 px/in)","method":"silhouette x_min in frame coordinates (negated); ± from hole-center and edge error","via":"harvest"},"note":"Rearmost point: the buffer-tower ring."},{"id":"left","value":1.147,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"rifle frame from reviewed holes takedown (1242.5,489.5) r=21px, pivot (223.5,488.5) r=22px = takedown(0.0, 0.0), pivot(6.375, 0.0) (159.8 px/in)","method":"silhouette x_min in frame coordinates (negated); ± from hole-center and edge error","via":"harvest"},"note":"Rearmost point: the buffer-tower ring."},{"id":"std","value":1.125,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"-{std.ar15.receiver_rear_x}","via":"user"},"note":"The ring's rear is the receiver's rear face, one plane where the end plate bears (rear_face_x reads it 1.134 and 1.136 below the ring)."}],"adopt":{"from":"std","reason":"The Army's drawing (7.503 −.006 from the pivot pin). The two photos read the ring's rim, which stands 0.25 in nearer the lens than the pins they are scaled by, so 0.02 to 0.04 far; the face below the ring, level with the pins, reads within 0.01 of the drawing."}},"front_ahead_of_pin":{"label":"Front of the pivot-pin lug ahead of the takedown pin","kind":"length","measurements":[{"id":"right","value":6.574,"unit":"in","pm":0.017,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"rifle frame from reviewed holes takedown (371.5,502.5) r=20px, pivot (1380.5,505.5) r=20px = takedown(0.0, 0.0), pivot(6.375, 0.0) (158.3 px/in)","method":"silhouette x_max in frame coordinates; ± from hole-center and edge error","via":"harvest"},"note":"Front of the pivot-pin lug."},{"id":"left","value":6.56,"unit":"in","pm":0.017,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"rifle frame from reviewed holes takedown (1242.5,489.5) r=21px, pivot (223.5,488.5) r=22px = takedown(0.0, 0.0), pivot(6.375, 0.0) (159.8 px/in)","method":"silhouette x_max in frame coordinates; ± from hole-center and edge error","via":"harvest"},"note":"Front of the pivot-pin lug."},{"id":"trace-right","value":6.58,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"a pinhole camera fitted to the rims of 7 holes, 5 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer, guard_rear, guard_front at the ledger's places; selector (its y left to the fit)): lens 24.1 ± 0.9 in from the centre plane, standing over x 4.18, y -1.77, the side leaning 9.3 ± 0.4° to the sensor with its bottom nearer and 0.1° with the picture's right nearer; 158.3 px/in on the near face at the lens's foot; rims within 0.86 px rms","method":"x_max of the traced outline (tools/trace.py)","via":"harvest"},"note":"Front of the pivot-pin lug."},{"id":"trace-left","value":6.576,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"a pinhole camera fitted to the rims of 6 holes, 4 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer, guard_rear at the ledger's places; selector (its y left to the fit)): lens 23.9 ± 0.8 in from the centre plane, standing over x 3.82, y -2.09, the side leaning 10.6 ± 0.4° to the sensor with its bottom nearer and 0.8° with the picture's left nearer; 159.7 px/in on the near face at the lens's foot; rims within 0.72 px rms","method":"x_max of the traced outline (tools/trace.py)","via":"harvest"},"note":"Front of the pivot-pin lug."}],"adopt":{"from":"trace-right","reason":"Through the camera fitted to each photo (2026-10-05): 6.580 and 6.576. The two-pin frames read 6.574 and 6.560: level with the pins, where that frame is good."}},"tower_top_above_pin":{"label":"Top of the buffer-tower ring above the pin line","kind":"length","measurements":[{"id":"right","value":1.543,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"rifle frame from reviewed holes takedown (371.5,502.5) r=20px, pivot (1380.5,505.5) r=20px = takedown(0.0, 0.0), pivot(6.375, 0.0) (158.3 px/in)","method":"silhouette y_max in frame coordinates; ± from hole-center and edge error","via":"harvest"},"note":"Top of the buffer-tower ring."},{"id":"left","value":1.537,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"rifle frame from reviewed holes takedown (1242.5,489.5) r=21px, pivot (223.5,488.5) r=22px = takedown(0.0, 0.0), pivot(6.375, 0.0) (159.8 px/in)","method":"silhouette y_max in frame coordinates; ± from hole-center and edge error","via":"harvest"},"note":"Top of the buffer-tower ring."},{"id":"std","value":1.5735,"unit":"in","pm":0.0065,"source":{"type":"derived","expr":"{std.ar15.buffer_tower_top_y}","via":"user"}}],"adopt":{"from":"std","reason":"The Army's drawing (1.325 above the deck). The two photos read the ring's top on the mid-plane, 0.44 in further from the lens than the pins they are scaled by, so 0.03 short; with the ring's radius they gave M2's low axis."}},"deck_above_pin":{"label":"Receiver top deck above the pin line","kind":"length","measurements":[{"id":"right","value":0.254,"unit":"in","pm":0.009,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"rifle frame from reviewed holes takedown (371.5,502.5) r=20px, pivot (1380.5,505.5) r=20px = takedown(0.0, 0.0), pivot(6.375, 0.0) (158.3 px/in)","method":"silhouette y_max in x [0.6, 5.8] in frame coordinates; ± from hole-center and edge error","via":"harvest"},"note":"Receiver top edge between the tower and the pivot lug (where the upper sits)."},{"id":"left","value":0.247,"unit":"in","pm":0.009,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"rifle frame from reviewed holes takedown (1242.5,489.5) r=21px, pivot (223.5,488.5) r=22px = takedown(0.0, 0.0), pivot(6.375, 0.0) (159.8 px/in)","method":"silhouette y_max in x [0.6, 5.8] in frame coordinates; ± from hole-center and edge error","via":"harvest"},"note":"Receiver top edge between the tower and the pivot lug (where the upper sits)."},{"id":"std","value":0.2485,"unit":"in","pm":0.0015,"source":{"type":"derived","expr":"{std.ar15.deck_y}","via":"user"},"note":"The Army's drawing: .250 −.003 above the line through the pins."},{"id":"trace-right","value":0.244,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"a pinhole camera fitted to the rims of 7 holes, 5 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer, guard_rear, guard_front at the ledger's places; selector (its y left to the fit)): lens 24.1 ± 0.9 in from the centre plane, standing over x 4.18, y -1.77, the side leaning 9.3 ± 0.4° to the sensor with its bottom nearer and 0.1° with the picture's right nearer; 158.3 px/in on the near face at the lens's foot; rims within 0.86 px rms","method":"y_max in x [0.6, 2.8] of the traced outline (tools/trace.py)","via":"harvest"},"note":"The receiver's top edge behind the magazine well (clear of the roll along the well's top, which stands nearer the lens)."},{"id":"trace-left","value":0.246,"unit":"in","pm":0.009,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"a pinhole camera fitted to the rims of 6 holes, 4 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer, guard_rear at the ledger's places; selector (its y left to the fit)): lens 23.9 ± 0.8 in from the centre plane, standing over x 3.82, y -2.09, the side leaning 10.6 ± 0.4° to the sensor with its bottom nearer and 0.8° with the picture's left nearer; 159.7 px/in on the near face at the lens's foot; rims within 0.72 px rms","method":"y_max in x [0.6, 2.8] of the traced outline (tools/trace.py)","via":"harvest"},"note":"The receiver's top edge behind the magazine well (clear of the roll along the well's top, which stands nearer the lens)."}],"adopt":{"from":"std","reason":"The Army's drawing, since 2026-10-12: the deck is the seat every upper sits on, and the model's is drawn on the drawing's plane (pipeline/blender/lib.py deck_outline). The right photo's 0.254, adopted until then, is the top of the roll along the well's right wall, which stands 0.11 in nearer the lens than the body; behind the well the two photos' cameras read the deck 0.244 and 0.246, either side of the drawing within their ±. The 22RB's receiver had been cut to the 0.254 and is on the drawing's plane too."}},"bottom_below_pin":{"label":"Lowest point below the pin line (trigger-guard ears)","kind":"length","measurements":[{"id":"right","value":2.4,"unit":"in","pm":0.011,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"rifle frame from reviewed holes takedown (371.5,502.5) r=20px, pivot (1380.5,505.5) r=20px = takedown(0.0, 0.0), pivot(6.375, 0.0) (158.3 px/in)","method":"silhouette y_min in frame coordinates (negated); ± from hole-center and edge error","via":"harvest"},"note":"Lowest point (trigger-guard ears / magwell front)."},{"id":"left","value":2.409,"unit":"in","pm":0.011,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"rifle frame from reviewed holes takedown (1242.5,489.5) r=21px, pivot (223.5,488.5) r=22px = takedown(0.0, 0.0), pivot(6.375, 0.0) (159.8 px/in)","method":"silhouette y_min in frame coordinates (negated); ± from hole-center and edge error","via":"harvest"},"note":"Lowest point (trigger-guard ears / magwell front)."},{"id":"trace-right","value":2.368,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"a pinhole camera fitted to the rims of 7 holes, 5 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer, guard_rear, guard_front at the ledger's places; selector (its y left to the fit)): lens 24.1 ± 0.9 in from the centre plane, standing over x 4.18, y -1.77, the side leaning 9.3 ± 0.4° to the sensor with its bottom nearer and 0.1° with the picture's right nearer; 158.3 px/in on the near face at the lens's foot; rims within 0.86 px rms","method":"−y_min of the traced outline (tools/trace.py)","via":"harvest"},"note":"Lowest point: the trigger guard's ears and the well's rear lip."},{"id":"trace-left","value":2.375,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"a pinhole camera fitted to the rims of 6 holes, 4 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer, guard_rear at the ledger's places; selector (its y left to the fit)): lens 23.9 ± 0.8 in from the centre plane, standing over x 3.82, y -2.09, the side leaning 10.6 ± 0.4° to the sensor with its bottom nearer and 0.8° with the picture's left nearer; 159.7 px/in on the near face at the lens's foot; rims within 0.72 px rms","method":"−y_min of the traced outline (tools/trace.py)","via":"harvest"},"note":"Lowest point: the trigger guard's ears and the well's rear lip."}],"adopt":{"from":"trace-right","reason":"Through the camera fitted to each photo (2026-10-05): 2.368 and 2.375. The two-pin frames' 2.400 and 2.409 were 0.03 long by the frame: the picture is 1.6% larger 2.4 in below the pins than on their line."}},"grip_shelf_top_y":{"label":"Grip shelf, upper-rear end, Y","kind":"length","measurements":[{"id":"right","value":-1.563,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"rifle frame from reviewed holes takedown (371.5,502.5) r=20px, pivot (1380.5,505.5) r=20px = takedown(0.0, 0.0), pivot(6.375, 0.0) (158.3 px/in)","method":"silhouette y_min in x [0.18, 0.24] in frame coordinates; ± from hole-center and edge error","via":"harvest"},"note":"Upper-rear end of the sloped grip-contact shelf (just ahead of the step at x ≈ 0.15)."},{"id":"left","value":-1.567,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"rifle frame from reviewed holes takedown (1242.5,489.5) r=21px, pivot (223.5,488.5) r=22px = takedown(0.0, 0.0), pivot(6.375, 0.0) (159.8 px/in)","method":"silhouette y_min in x [0.18, 0.24] in frame coordinates; ± from hole-center and edge error","via":"harvest"},"note":"Upper-rear end of the sloped grip-contact shelf (just ahead of the step at x ≈ 0.15)."},{"id":"trace-right","value":-1.55,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"a pinhole camera fitted to the rims of 7 holes, 5 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer, guard_rear, guard_front at the ledger's places; selector (its y left to the fit)): lens 24.1 ± 0.9 in from the centre plane, standing over x 4.18, y -1.77, the side leaning 9.3 ± 0.4° to the sensor with its bottom nearer and 0.1° with the picture's right nearer; 158.3 px/in on the near face at the lens's foot; rims within 0.86 px rms","method":"y_min in x [0.18, 0.24] of the traced outline (tools/trace.py)","via":"harvest"},"note":"Upper-rear end of the lug's sloped face (just ahead of its rear face)."},{"id":"trace-left","value":-1.545,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"a pinhole camera fitted to the rims of 6 holes, 4 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer, guard_rear at the ledger's places; selector (its y left to the fit)): lens 23.9 ± 0.8 in from the centre plane, standing over x 3.82, y -2.09, the side leaning 10.6 ± 0.4° to the sensor with its bottom nearer and 0.8° with the picture's left nearer; 159.7 px/in on the near face at the lens's foot; rims within 0.72 px rms","method":"y_min in x [0.18, 0.24] of the traced outline (tools/trace.py)","via":"harvest"},"note":"Upper-rear end of the lug's sloped face (just ahead of its rear face)."}],"adopt":{"from":"trace-right","reason":"Through the camera fitted to each photo (2026-10-05), on the lug's near side: -1.550 and -1.545; the two-pin frames read -1.563 and -1.567."},"note":"The bottom of the step behind the tang, where the sloped web starts. Not where the grip seats (see grip_seat_y): the web covers the grip's top from the side."},"grip_mating_y":{"label":"Receiver underside behind the step (where a grip's flat top bears), Y","kind":"length","measurements":[{"id":"right","value":-1.096,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"rifle frame from reviewed holes takedown (371.5,502.5) r=20px, pivot (1380.5,505.5) r=20px = takedown(0.0, 0.0), pivot(6.375, 0.0) (158.3 px/in)","method":"silhouette y_min in x [-0.2, 0.08] in frame coordinates; ± from hole-center and edge error","via":"harvest"},"note":"The receiver's underside just behind the step (the tang), where a grip's flat top bears."},{"id":"left","value":-1.092,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"rifle frame from reviewed holes takedown (1242.5,489.5) r=21px, pivot (223.5,488.5) r=22px = takedown(0.0, 0.0), pivot(6.375, 0.0) (159.8 px/in)","method":"silhouette y_min in x [-0.2, 0.08] in frame coordinates; ± from hole-center and edge error","via":"harvest"},"note":"The receiver's underside just behind the step (the tang), where a grip's flat top bears."},{"id":"trace-right","value":-1.072,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"a pinhole camera fitted to the rims of 7 holes, 5 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer, guard_rear, guard_front at the ledger's places; selector (its y left to the fit)): lens 24.1 ± 0.9 in from the centre plane, standing over x 4.18, y -1.77, the side leaning 9.3 ± 0.4° to the sensor with its bottom nearer and 0.1° with the picture's right nearer; 158.3 px/in on the near face at the lens's foot; rims within 0.86 px rms","method":"y_min in x [-0.2, 0.08] of the traced outline (tools/trace.py)","via":"harvest"},"note":"The underside behind the lug, where a grip's flat top bears, read on the far edge of its flat."},{"id":"trace-left","value":-1.062,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"a pinhole camera fitted to the rims of 6 holes, 4 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer, guard_rear at the ledger's places; selector (its y left to the fit)): lens 23.9 ± 0.8 in from the centre plane, standing over x 3.82, y -2.09, the side leaning 10.6 ± 0.4° to the sensor with its bottom nearer and 0.8° with the picture's left nearer; 159.7 px/in on the near face at the lens's foot; rims within 0.72 px rms","method":"y_min in x [-0.2, 0.08] of the traced outline (tools/trace.py)","via":"harvest"},"note":"The underside behind the lug, where a grip's flat top bears, read on the far edge of its flat."}],"adopt":{"from":"trace-right","reason":"Through the camera fitted to each photo (2026-10-05) the underside reads -1.072 and -1.062, on the far edge of its flat, which is the edge a view from below shows; the Army drawing's -1.0695 is between them. The two-pin frames' -1.096 and -1.092 took that far edge for the near face's: it is 0.9 in further from a lens 24 in off and 0.7 in below it, which is 0.026 lower in the picture."}},"magazine_seat_x":{"label":"Magazine seat, X: where a magazine's frame origin (its spine's rear face at the feed-lip top) sits","kind":"length","measurements":[{"id":"flatlay","value":3.638,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/nordic-22rb-upper d0862b6dba98 (complete rifle lying flat, photographed straight down, a smoke Sonic X seated; supplied in chat)","scaleRef":"frame from the reviewed holes takedown (652.5,759.5) r=11px, pivot (966.5,767.5) r=15px, trigger (748.5,794.5) r=4px, selector (691.5,780.5) r=7px (49.2 px/in, rms 0.028 in over 4 points)","method":"x of the fitted profile's origin of the traced outline (tools/trace.py); the traced Sonic X outline's origin (its spine's rear face at the feed-lip top), fitted by rotation, translation and scale to the seated magazine's edges below the magwell (rms 0.032 in): the photo has the magazine at 0.973 of its size","via":"user"},"note":"3.633 until 2026-10-03, fitted at the scale of an outline traced from a retailer's photo. The user's own magazine is 2.514 from its rib to its front face (blackdog-22lr-15.front_to_back): at 3.64 its front face would stand 0.13 in inside the well's front wall (std.ar15.magwell_front_inner_x, 6.025), and its catch notch 0.14 ahead of the catch. This frame is 2.7% small at the magazine; why it reads the magazine forward isn't found."},{"id":"seated-25","value":3.443,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/blackdog-22lr-25 6e65a9040370 (green 25-round seated in a custom AR-15, straight right side, 650 px; supplied in chat)","scaleRef":"frame from the reviewed holes takedown, pivot, trigger (41.5 px/in, rms 0.031 in over 3 points)","method":"x of the fitted profile's origin of the traced outline (tools/trace.py); the traced 25-round outline's origin (its spine's rear face at the feed-lip top), fitted by rotation and translation at the outline's own scale to the seated magazine's edges below the magwell","via":"user"}},{"id":"well","value":3.4915,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{std.ar15.magwell_front_inner_x} - ({std.ar15.magwell_length} + {blackdog-22lr-15.front_to_back}) / 2","via":"user"},"note":"The magazine in the middle of the well the Army's drawing dimensions: its spine rib in the well's spine slot, its front face behind the front inner wall. The well is 2.553 long and the user's own magazine 2.514, so it can stand 0.02 either side of this. There its catch notch (0.481 to 1.048 from its rib's rear face) spans X 3.97 to 4.54, where the Workhorse's left wall has the catch's band (std.ar15.magwell_band_rear_x 3.975 to magwell_band_front_x 4.549)."}],"adopt":{"from":"well","reason":"A magazine can't stand inside the well's wall: the drawing's well and the user's own magazine, measured beside a tape, leave it 0.04 in of play, and its catch notch then lies on the catch. The green 25-round's seated photo agrees (3.443 ± 0.06). The flat-lay's reading (3.638; 3.633 with the retailer's outline), adopted until 2026-10-03, would put its front face 0.13 in into the front wall; it is kept as the conflict it is."},"note":"Measured with a Black Dog Sonic X seated in the user's flat-lay (a mil-spec lower, framed by four standard pins). Magazines that share its top section (the 25-round) seat the same way. The green 25-round in the user's seated photo (6e65a9040370) is Black Dog's own Instagram screenshot of a V208 (lime green, finger grooves), not a Sonic X (research agent, 2026-10-01); its seat agrees with the Sonic X's as far as the two share a top section."},"magazine_seat_y":{"label":"Magazine seat, Y: the feed-lip top of a seated magazine","kind":"length","measurements":[{"id":"flatlay","value":0.995,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/nordic-22rb-upper d0862b6dba98 (complete rifle lying flat, photographed straight down, a smoke Sonic X seated; supplied in chat)","scaleRef":"frame from the reviewed holes takedown (652.5,759.5) r=11px, pivot (966.5,767.5) r=15px, trigger (748.5,794.5) r=4px, selector (691.5,780.5) r=7px (49.2 px/in, rms 0.028 in over 4 points)","method":"y of the fitted profile's origin of the traced outline (tools/trace.py); the traced Sonic X outline's origin (its spine's rear face at the feed-lip top), fitted by rotation, translation and scale to the seated magazine's edges below the magwell (rms 0.032 in): the photo has the magazine at 0.973 of its size","via":"user"},"note":"1.016 ± 0.15 until 2026-10-03, fitted at a fixed scale: the fit locks onto the base, 5.8 in below, so the outline's size moved the top (at the size the user's own magazine measures, a fixed-scale fit read 1.151). With the scale free the top no longer depends on it."},{"id":"seated-25","value":1.224,"unit":"in","pm":0.15,"source":{"type":"photo","photo":"references/blackdog-22lr-25 6e65a9040370 (green 25-round seated in a custom AR-15, straight right side, 650 px; supplied in chat)","scaleRef":"frame from the reviewed holes takedown, pivot, trigger (41.5 px/in, rms 0.031 in over 3 points)","method":"y of the fitted profile's origin of the traced outline (tools/trace.py); the traced 25-round outline's origin (its spine's rear face at the feed-lip top), fitted by rotation and translation at the outline's own scale to the seated magazine's edges below the magwell; ± includes the outline's own scale over the 7.8 in from its base","via":"user"},"note":"1.051 until 2026-10-03. The fit locks onto the base, 8 in below, so the top is the base plus the outline's height, which is the Sonic X 25's (7.972 since the shared top section was measured; 7.801 before) laid on a photo of a V208: it places the base, not the top."},{"id":"catch","value":1.003,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{std.ar15.mag_catch_slot_bottom_y} + {std.ar15.mag_catch_slot_h} + {blackdog-22lr-15.catch_notch_top}","via":"user"},"note":"The magazine hanging on the catch: its notch's upper edge (1.44 below its feed lips' top, on the user's own magazine) on the catch's upper face, taken at the top of the slot the catch comes through (the Army's drawing). The notch is 0.30 tall and the slot .252: pushed up against the catch it would be 0.05 higher, and a catch thinner than its slot would let it hang lower by the difference. ± covers both."}],"adopt":{"from":"catch","reason":"A seated magazine hangs on the catch, whose slot the drawing places and whose notch the user's own magazine shows. The flat-lay's fit with its scale free (0.995 ± 0.05) agrees; the green 25-round's photo (a V208 under the Sonic X 25's outline: 1.224 ± 0.15) places its base, not its top."},"note":"Where a seated magazine's feed lips' top is. Since 2026-10-03 from the catch: the Army drawing's slot and the notch on the user's own magazine. It is 0.13 in above the bore's axis (std.ar15.bore_axis_y, 0.8775); where the round itself sits in the feed-lip block isn't visible from outside. Until then it was the flat-lay's fit at a fixed scale, which locks onto the base 5.8 in below: its height moved with the outline's size."},"grip_seat_y":{"label":"Grip seat, Y: the grip's mating face at its rear end","kind":"length","measurements":[{"id":"mating","value":-1.072,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{.grip_mating_y}","via":"user"},"note":"The grip is screwed up against the underside."},{"id":"tdp","value":-1.0695,"unit":"in","pm":0.0115,"source":{"type":"derived","expr":"{std.ar15.deck_y} - {std.ar15.grip_seat_below_deck}","via":"user"},"note":"The Army's drawing: the flat the lug hangs from, 1.318 ±.010 below the top deck."},{"id":"k2-installed","value":-1.175,"unit":"in","pm":0.055,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 5d5e23b08431 (MOE-K2+ installed on a mil-spec lower, straight right side, 1200 px; supplied in chat)","scaleRef":"frame from the reviewed holes takedown, selector, trigger, hammer (118.8 px/in, rms 0.056 in over 4 points)","method":"y of the fitted profile's origin of the traced outline (tools/trace.py); the traced outline's origin (its flat top's rear end), fitted by rotation and translation (at the outline's own scale) to the grip's edges against the background","via":"user"},"note":"Read with the K2+ outline 12% too large (2026-10-03: its drop is 4.15, not 4.65), in a frame whose four picks disagree pair by pair and in which the grip reads 10% large: kept as read, and not read again (the fit is now made at a free scale for the lean alone)."}],"adopt":{"from":"tdp","reason":"The Army's drawing (1.318 ±.010 below the top deck). Through their cameras the two photos read the underside -1.072 and -1.062 (grip_mating_y), either side of it. Until 2026-10-05 the two-pin frames' -1.096, which was the underside's far edge read as its near one: every grip sat 0.027 in low on this lower. The K2+ product photo's -1.175 was read with an outline 12% too large."},"note":"The grip's flat top bears on the receiver's underside (grip_mating_y). M2 anchored the grip at grip_shelf_top (the bottom of the step, −1.56), which hung it ~0.47 in low; until 2026-10-05 the seat was that underside as two-pin frames read it, 0.027 low."},"grip_shelf_bottom_y":{"label":"Grip shelf, lower-front end, Y","kind":"length","measurements":[{"id":"right","value":-2.016,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"rifle frame from reviewed holes takedown (371.5,502.5) r=20px, pivot (1380.5,505.5) r=20px = takedown(0.0, 0.0), pivot(6.375, 0.0) (158.3 px/in)","method":"silhouette y_min in x [0.3, 1.12] in frame coordinates; ± from hole-center and edge error","via":"harvest"},"note":"Lower-front end of the grip-contact shelf, just behind the trigger-guard rear ear."},{"id":"left","value":-2.019,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"rifle frame from reviewed holes takedown (1242.5,489.5) r=21px, pivot (223.5,488.5) r=22px = takedown(0.0, 0.0), pivot(6.375, 0.0) (159.8 px/in)","method":"silhouette y_min in x [0.3, 1.12] in frame coordinates; ± from hole-center and edge error","via":"harvest"},"note":"Lower-front end of the grip-contact shelf, just behind the trigger-guard rear ear."},{"id":"trace-right","value":-2.002,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"a pinhole camera fitted to the rims of 7 holes, 5 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer, guard_rear, guard_front at the ledger's places; selector (its y left to the fit)): lens 24.1 ± 0.9 in from the centre plane, standing over x 4.18, y -1.77, the side leaning 9.3 ± 0.4° to the sensor with its bottom nearer and 0.1° with the picture's right nearer; 158.3 px/in on the near face at the lens's foot; rims within 0.86 px rms","method":"y_min in x [0.3, 1.12] of the traced outline (tools/trace.py)","via":"harvest"},"note":"The lug's bottom flat, just behind the guard's rear ears."},{"id":"trace-left","value":-1.996,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"a pinhole camera fitted to the rims of 6 holes, 4 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer, guard_rear at the ledger's places; selector (its y left to the fit)): lens 23.9 ± 0.8 in from the centre plane, standing over x 3.82, y -2.09, the side leaning 10.6 ± 0.4° to the sensor with its bottom nearer and 0.8° with the picture's left nearer; 159.7 px/in on the near face at the lens's foot; rims within 0.72 px rms","method":"y_min in x [0.3, 1.12] of the traced outline (tools/trace.py)","via":"harvest"},"note":"The lug's bottom flat, just behind the guard's rear ears."}],"adopt":{"from":"trace-right","reason":"Through the camera fitted to each photo (2026-10-05), on the lug's near side: -2.002 and -1.996, the Army drawing's -1.9995 (.93 below the seat) between them. The two-pin frames' -2.016 and -2.019 were low by the frame: the picture is 1.4% larger there than on the pin line."}},"grip_shelf_top_x":{"label":"Grip shelf start (step), X","kind":"length","measurements":[{"id":"right","value":0.133,"unit":"in","pm":0.009,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"rifle frame from reviewed holes takedown (371.5,502.5) r=20px, pivot (1380.5,505.5) r=20px = takedown(0.0, 0.0), pivot(6.375, 0.0) (158.3 px/in)","method":"silhouette x_min in x [0.0, 0.6] in y [-1.5, -1.3] in frame coordinates; ± from hole-center and edge error","via":"harvest"},"note":"The step where the grip shelf starts (a near-vertical edge between y −1.1 and −1.56)."},{"id":"left","value":0.139,"unit":"in","pm":0.009,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"rifle frame from reviewed holes takedown (1242.5,489.5) r=21px, pivot (223.5,488.5) r=22px = takedown(0.0, 0.0), pivot(6.375, 0.0) (159.8 px/in)","method":"silhouette x_min in x [0.0, 0.6] in y [-1.5, -1.3] in frame coordinates; ± from hole-center and edge error","via":"harvest"},"note":"The step where the grip shelf starts (a near-vertical edge between y −1.1 and −1.56)."},{"id":"trace-right","value":0.122,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"a pinhole camera fitted to the rims of 7 holes, 5 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer, guard_rear, guard_front at the ledger's places; selector (its y left to the fit)): lens 24.1 ± 0.9 in from the centre plane, standing over x 4.18, y -1.77, the side leaning 9.3 ± 0.4° to the sensor with its bottom nearer and 0.1° with the picture's right nearer; 158.3 px/in on the near face at the lens's foot; rims within 0.86 px rms","method":"x_min in x [0.0, 0.6] in y [-1.45, -1.15] of the traced outline (tools/trace.py)","via":"harvest"},"note":"The lug's upright rear face, on the lug's near side."},{"id":"trace-left","value":0.126,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"a pinhole camera fitted to the rims of 6 holes, 4 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer, guard_rear at the ledger's places; selector (its y left to the fit)): lens 23.9 ± 0.8 in from the centre plane, standing over x 3.82, y -2.09, the side leaning 10.6 ± 0.4° to the sensor with its bottom nearer and 0.8° with the picture's left nearer; 159.7 px/in on the near face at the lens's foot; rims within 0.72 px rms","method":"x_min in x [0.0, 0.6] in y [-1.45, -1.15] of the traced outline (tools/trace.py)","via":"harvest"},"note":"The lug's upright rear face, on the lug's near side."}],"adopt":{"from":"trace-right","reason":"Through the camera fitted to each photo (2026-10-05), on the lug's near side: 0.122 and 0.126. The lug's rear face is the Workhorse's own: the Army's drawing has it 0.075 behind the takedown pin (std.ar15.grip_lug_front_from_rear_face less grip_lug_length), 0.20 further back, and neither a frame nor a lens moves an edge 31 px. The two-pin frames read 0.133 and 0.139: the lug is 0.25 in further from the lens than the near face."}},"trigger_opening_top_y":{"label":"Receiver underside above the trigger opening, Y","kind":"length","measurements":[{"id":"right","value":-1.129,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"rifle frame from reviewed holes takedown (371.5,502.5) r=20px, pivot (1380.5,505.5) r=20px = takedown(0.0, 0.0), pivot(6.375, 0.0) (158.3 px/in)","method":"silhouette y_min in x [1.8, 3.0] in frame coordinates; ± from hole-center and edge error","via":"harvest"},"note":"Receiver underside above the trigger-guard opening."},{"id":"left","value":-1.131,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"rifle frame from reviewed holes takedown (1242.5,489.5) r=21px, pivot (223.5,488.5) r=22px = takedown(0.0, 0.0), pivot(6.375, 0.0) (159.8 px/in)","method":"silhouette y_min in x [1.8, 3.0] in frame coordinates; ± from hole-center and edge error","via":"harvest"},"note":"Receiver underside above the trigger-guard opening."},{"id":"trace-right","value":-1.064,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"a pinhole camera fitted to the rims of 7 holes, 5 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer, guard_rear, guard_front at the ledger's places; selector (its y left to the fit)): lens 24.1 ± 0.9 in from the centre plane, standing over x 4.18, y -1.77, the side leaning 9.3 ± 0.4° to the sensor with its bottom nearer and 0.1° with the picture's right nearer; 158.3 px/in on the near face at the lens's foot; rims within 0.86 px rms","method":"y_min in x [1.95, 2.9] of the traced outline (tools/trace.py)","via":"harvest"},"note":"Receiver underside above the trigger opening, on its far edge."},{"id":"trace-left","value":-1.065,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"a pinhole camera fitted to the rims of 6 holes, 4 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer, guard_rear at the ledger's places; selector (its y left to the fit)): lens 23.9 ± 0.8 in from the centre plane, standing over x 3.82, y -2.09, the side leaning 10.6 ± 0.4° to the sensor with its bottom nearer and 0.8° with the picture's left nearer; 159.7 px/in on the near face at the lens's foot; rims within 0.72 px rms","method":"y_min in x [1.95, 2.9] of the traced outline (tools/trace.py)","via":"harvest"},"note":"Receiver underside above the trigger opening, on its far edge."}],"adopt":{"from":"trace-right","reason":"Through the camera fitted to each photo (2026-10-05), on the underside's far edge (a view from below shows that one): -1.064 and -1.065. The two-pin frames' -1.129 and -1.131 took the far edge for the near face's, over a stretch that ran into the corner ahead of it."}},"magwell_front_x":{"label":"Magwell front face, X","kind":"length","measurements":[{"id":"right","value":6.2,"unit":"in","pm":0.016,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"rifle frame from reviewed holes takedown (371.5,502.5) r=20px, pivot (1380.5,505.5) r=20px = takedown(0.0, 0.0), pivot(6.375, 0.0) (158.3 px/in)","method":"silhouette x_max in x [3.0, 7.0] in y [-1.95, -1.3] in frame coordinates; ± from hole-center and edge error","via":"harvest"},"note":"Front face of the magwell."},{"id":"left","value":6.195,"unit":"in","pm":0.016,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"rifle frame from reviewed holes takedown (1242.5,489.5) r=21px, pivot (223.5,488.5) r=22px = takedown(0.0, 0.0), pivot(6.375, 0.0) (159.8 px/in)","method":"silhouette x_max in x [3.0, 7.0] in y [-1.95, -1.3] in frame coordinates; ± from hole-center and edge error","via":"harvest"},"note":"Front face of the magwell."},{"id":"trace-right","value":6.179,"unit":"in","pm":0.011,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"a pinhole camera fitted to the rims of 7 holes, 5 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer, guard_rear, guard_front at the ledger's places; selector (its y left to the fit)): lens 24.1 ± 0.9 in from the centre plane, standing over x 4.18, y -1.77, the side leaning 9.3 ± 0.4° to the sensor with its bottom nearer and 0.1° with the picture's right nearer; 158.3 px/in on the near face at the lens's foot; rims within 0.86 px rms","method":"x_max in x [3.0, 7.0] in y [-1.95, -1.3] of the traced outline (tools/trace.py)","via":"harvest"},"note":"Front face of the magazine well, on its near wall."},{"id":"trace-left","value":6.174,"unit":"in","pm":0.011,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"a pinhole camera fitted to the rims of 6 holes, 4 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer, guard_rear at the ledger's places; selector (its y left to the fit)): lens 23.9 ± 0.8 in from the centre plane, standing over x 3.82, y -2.09, the side leaning 10.6 ± 0.4° to the sensor with its bottom nearer and 0.8° with the picture's left nearer; 159.7 px/in on the near face at the lens's foot; rims within 0.72 px rms","method":"x_max in x [3.0, 7.0] in y [-1.95, -1.3] of the traced outline (tools/trace.py)","via":"harvest"},"note":"Front face of the magazine well, on its near wall."}],"adopt":{"from":"trace-right","reason":"Through the camera fitted to each photo (2026-10-05), on the well's near wall: 6.179 and 6.174. The two-pin frames read 6.200 and 6.195: the wall stands 0.11 in nearer the lens than the face the pins' rims are on, and reads further from the point the lens stands over."}},"tower_front_x":{"label":"Buffer-tower front edge (side walls), X","kind":"length","measurements":[{"id":"right","value":-0.314,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"rifle frame from reviewed holes takedown (371.5,502.5) r=20px, pivot (1380.5,505.5) r=20px = takedown(0.0, 0.0), pivot(6.375, 0.0) (158.3 px/in)","method":"silhouette x_max in x [-1.5, 3.0] in y [0.5, 1.4] in frame coordinates; ± from hole-center and edge error","via":"harvest"},"note":"Front face of the buffer tower, above the deck."},{"id":"left","value":-0.322,"unit":"in","pm":0.009,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"rifle frame from reviewed holes takedown (1242.5,489.5) r=21px, pivot (223.5,488.5) r=22px = takedown(0.0, 0.0), pivot(6.375, 0.0) (159.8 px/in)","method":"silhouette x_max in x [-1.5, 3.0] in y [0.5, 1.4] in frame coordinates; ± from hole-center and edge error","via":"harvest"},"note":"Front face of the buffer tower, above the deck."},{"id":"trace-right","value":-0.317,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"a pinhole camera fitted to the rims of 7 holes, 5 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer, guard_rear, guard_front at the ledger's places; selector (its y left to the fit)): lens 24.1 ± 0.9 in from the centre plane, standing over x 4.18, y -1.77, the side leaning 9.3 ± 0.4° to the sensor with its bottom nearer and 0.1° with the picture's right nearer; 158.3 px/in on the near face at the lens's foot; rims within 0.86 px rms","method":"x_max in x [-1.5, 3.0] in y [0.5, 1.4] of the traced outline (tools/trace.py)","via":"harvest"},"note":"Front edge of the buffer tower's side walls, above the deck (read at the near face's depth)."},{"id":"trace-left","value":-0.329,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"a pinhole camera fitted to the rims of 6 holes, 4 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer, guard_rear at the ledger's places; selector (its y left to the fit)): lens 23.9 ± 0.8 in from the centre plane, standing over x 3.82, y -2.09, the side leaning 10.6 ± 0.4° to the sensor with its bottom nearer and 0.8° with the picture's left nearer; 159.7 px/in on the near face at the lens's foot; rims within 0.72 px rms","method":"x_max in x [-1.5, 3.0] in y [0.5, 1.4] of the traced outline (tools/trace.py)","via":"harvest"},"note":"Front edge of the buffer tower's side walls, above the deck (read at the near face's depth)."}],"adopt":{"from":"trace-right","reason":"Through the camera fitted to each photo (2026-10-05), at the near face's depth: -0.317 and -0.329; the two-pin frames read -0.314 and -0.322."},"note":"The silhouette's front edge above the deck. Not the walls' own edge (2026-10-12): both photos are taken from ahead of the tower (the lens over X 4.18 and 3.82), and what stands furthest forward in them between Y 0.5 and 1.4 is the far wall and the ring's threaded inside seen through its front, a fifth of an inch ahead of the near wall's edge, which in the right photo is on the Army drawing's arc (std.ar15.rear_wall_arc_r) within 0.03. The model's walls are that arc's; this figure is how far forward they are drawn at the ring's width under it."},"rear_face_x":{"label":"Receiver rear face below the tower ring, X","kind":"length","measurements":[{"id":"right","value":-1.134,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"rifle frame from reviewed holes takedown (371.5,502.5) r=20px, pivot (1380.5,505.5) r=20px = takedown(0.0, 0.0), pivot(6.375, 0.0) (158.3 px/in)","method":"silhouette x_min in y [-1.0, 0.0] in frame coordinates; ± from hole-center and edge error","via":"harvest"},"note":"Rear face of the receiver below the buffer-tower ring."},{"id":"left","value":-1.136,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"rifle frame from reviewed holes takedown (1242.5,489.5) r=21px, pivot (223.5,488.5) r=22px = takedown(0.0, 0.0), pivot(6.375, 0.0) (159.8 px/in)","method":"silhouette x_min in y [-1.0, 0.0] in frame coordinates; ± from hole-center and edge error","via":"harvest"},"note":"Rear face of the receiver below the buffer-tower ring."},{"id":"trace-right","value":-1.128,"unit":"in","pm":0.011,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"a pinhole camera fitted to the rims of 7 holes, 5 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer, guard_rear, guard_front at the ledger's places; selector (its y left to the fit)): lens 24.1 ± 0.9 in from the centre plane, standing over x 4.18, y -1.77, the side leaning 9.3 ± 0.4° to the sensor with its bottom nearer and 0.1° with the picture's right nearer; 158.3 px/in on the near face at the lens's foot; rims within 0.86 px rms","method":"x_min in y [-0.5, -0.15] of the traced outline (tools/trace.py)","via":"harvest"},"note":"Rear face of the receiver below the buffer tower's ring, down to where it rounds into the underside."},{"id":"trace-left","value":-1.126,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"a pinhole camera fitted to the rims of 6 holes, 4 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer, guard_rear at the ledger's places; selector (its y left to the fit)): lens 23.9 ± 0.8 in from the centre plane, standing over x 3.82, y -2.09, the side leaning 10.6 ± 0.4° to the sensor with its bottom nearer and 0.8° with the picture's left nearer; 159.7 px/in on the near face at the lens's foot; rims within 0.72 px rms","method":"x_min in y [-0.5, -0.15] of the traced outline (tools/trace.py)","via":"harvest"},"note":"Rear face of the receiver below the buffer tower's ring, down to where it rounds into the underside."}],"adopt":{"from":"trace-right","reason":"Through the camera fitted to each photo (2026-10-05): -1.128 and -1.126, the Army drawing's -1.125 (std.ar15.receiver_rear_x) within 0.003, and upright all the way down once its lower end is read as the half-round across the body that it is. The two-pin frames read -1.134 and -1.136."}},"fence_rear_x":{"label":"The magazine catch's fence, its flat face's rear edge, X","kind":"length","measurements":[{"id":"right","value":3.02,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"rifle frame from reviewed holes takedown (371.5,502.5), pivot (1380.5,505.5) = (0, 0), (6.375, 0) (158.3 px/in)","method":"brightness along rows Y -0.30 and -0.82 (5 px bands): the slope's shadow from 2.91 to 3.02, the face from 3.02","via":"harvest"}}],"note":"The raised panel the button's pocket opens through, on the right. Its flat face is where the photo's brightness is the panel's (about 100 of 255) between the dark slopes down to the body; the slopes are about 0.1 in wide. The reference model's mil-spec fence face (std.ar15.mag_catch_fence_out) runs X 3.023 to 3.566, Y -0.922 to -0.188: the same face within a few hundredths."},"fence_front_x":{"label":"The magazine catch's fence, its flat face's front edge, X","kind":"length","measurements":[{"id":"right","value":3.565,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"rifle frame from reviewed holes takedown (371.5,502.5), pivot (1380.5,505.5) = (0, 0), (6.375, 0) (158.3 px/in)","method":"brightness along rows Y -0.30, -0.56 and -0.82: the face to 3.56-3.57, then the groove before the well's wall","via":"harvest"}}]},"fence_top_y":{"label":"The magazine catch's fence, its flat face's top edge, Y","kind":"length","measurements":[{"id":"right","value":-0.22,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"rifle frame from reviewed holes takedown (371.5,502.5), pivot (1380.5,505.5) = (0, 0), (6.375, 0) (158.3 px/in)","method":"brightness down columns X 3.05 and 3.50: the face from -0.205 and -0.237 down, the top rib's slope above","via":"harvest"}}]},"fence_bottom_y":{"label":"The magazine catch's fence, its flat face's bottom edge, Y","kind":"length","measurements":[{"id":"right","value":-0.91,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"rifle frame from reviewed holes takedown (371.5,502.5), pivot (1380.5,505.5) = (0, 0), (6.375, 0) (158.3 px/in)","method":"brightness down columns X 3.05, 3.29 and 3.50: the face to -0.913, -0.913 and -0.894","via":"harvest"}}]},"fence_corner_r":{"label":"The magazine catch's fence, its flat face's corners, radius","kind":"length","measurements":[{"id":"right","value":0.1,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"rifle frame from reviewed holes takedown (371.5,502.5), pivot (1380.5,505.5) = (0, 0), (6.375, 0) (158.3 px/in)","method":"the corners' arcs on a 3x crop around the pocket, about 15 px","via":"harvest"}}]},"magwell_wall_rear_x":{"label":"Magazine well's outside walls, rear edge, X (right side)","kind":"length","measurements":[{"id":"right","value":3.619,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"rifle frame from reviewed holes takedown (371.5,502.5), pivot (1380.5,505.5) = (0, 0), (6.375, 0) (158.3 px/in)","method":"darkest column of the groove in px 925–965, rows y −0.35 to −0.80 in (median px 943); ± is the groove's width","via":"harvest"}}],"note":"Where the walls (std.ar15.magwell_outside_width) stand out from the narrower body: on the right, the groove behind the vertical rib that runs down from the top rib beside the magazine-catch fence."},"magwell_wall_rear_x_left":{"label":"Magazine well's outside walls, rear edge, X (left side)","kind":"length","measurements":[{"id":"left","value":3.455,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"rifle frame from reviewed holes takedown (1242.5,489.5), pivot (223.5,488.5) = (0, 0), (6.375, 0) (159.8 px/in)","method":"darkest column of the step's shadow in px 600–800, rows y −1.07 to −1.63 in (px 689–694); ± is the shadow's width","via":"harvest"}}],"note":"On the left the wall's rear edge is the step down to the body ahead of the trigger guard's front ear; above y ≈ −0.9 it curves back toward the bolt catch's bosses (to x ≈ 3.0)."},"magwell_wall_upper_rear_x_left":{"label":"Magazine well's outside walls, rear edge above the step's curve, X (left side)","kind":"length","measurements":[{"id":"left","value":2.948,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"rifle frame from reviewed holes takedown (1242.5,489.5), pivot (223.5,488.5) = (0, 0), (6.375, 0) (159.8 px/in)","method":"darkest column of the step's shadow (3 px box filter) in px 750–800, rows every 8 px from Y +0.22 to -0.69: px 771–772 wherever the row misses the slots","via":"harvest"}}],"note":"On the left the wall's rear edge stands at this x from the deck down past the magazine catch's slot, then curves forward to the step ahead of the trigger guard's front ear (magwell_wall_rear_x_left): the wall carries the bolt catch's bosses and slot and the catch slot's rear end. The reference CAD model's runs straight down at X 3.023 (its face; its edge's radius behind)."},"magwell_wall_curve_top_y_left":{"label":"Magazine well's outside walls, left side, where the rear edge starts to curve forward, Y","kind":"length","measurements":[{"id":"left","value":-0.7,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"rifle frame from reviewed holes takedown (1242.5,489.5), pivot (223.5,488.5) = (0, 0), (6.375, 0) (159.8 px/in)","method":"the step's shadow, row by row: px 771 to Y -0.685, 769 at -0.735, 764 at -0.785","via":"harvest"}}]},"magwell_wall_curve_bottom_y_left":{"label":"Magazine well's outside walls, left side, where the rear edge's curve meets the step, Y","kind":"length","measurements":[{"id":"left","value":-1.12,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"rifle frame from reviewed holes takedown (1242.5,489.5), pivot (223.5,488.5) = (0, 0), (6.375, 0) (159.8 px/in)","method":"the step's shadow, row by row: px 693 at Y -1.086, 689–692 from -1.136 down","via":"harvest"}}],"note":"Between the two ends the edge is drawn as a smooth S (3t² − 2t³), within 0.06 of the shadow's column at every row read: X 2.994, 3.038, 3.101, 3.220, 3.364, 3.414, 3.439 at Y -0.785 to -1.086 every 0.05."},"bolt_catch_boss_rear_x":{"label":"Bolt catch bosses: the rear boss's rear edge, X (left side)","kind":"length","measurements":[{"id":"left","value":3.013,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"rifle frame from reviewed holes takedown (1242.5,489.5), pivot (223.5,488.5) = (0, 0), (6.375, 0) (159.8 px/in)","method":"edge picked on a 4x crop with a 10 px grid (px 761); ± is ~3 px","via":"harvest"}}]},"bolt_catch_gap_rear_x":{"label":"Bolt catch bosses: the gap between them (where the catch sits), rear edge, X","kind":"length","measurements":[{"id":"left","value":3.201,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"rifle frame from reviewed holes takedown (1242.5,489.5), pivot (223.5,488.5) = (0, 0), (6.375, 0) (159.8 px/in)","method":"edge picked on a 4x crop with a 10 px grid (px 731); ± is ~3 px","via":"harvest"}},{"id":"tdp","value":3.203,"unit":"in","source":{"type":"derived","expr":"{std.ar15.bolt_catch_slot_front_x} - {std.ar15.bolt_catch_slot_width}","via":"user"},"note":"The gap is the drawing's slot for the catch, at the left face."}],"adopt":{"from":"tdp","reason":"The drawing's slot (2026-10-03); the photo's edge agrees within 0.002."}},"bolt_catch_gap_front_x":{"label":"Bolt catch bosses: the gap's front edge, X","kind":"length","measurements":[{"id":"left","value":3.348,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"rifle frame from reviewed holes takedown (1242.5,489.5), pivot (223.5,488.5) = (0, 0), (6.375, 0) (159.8 px/in)","method":"edge picked on a 4x crop with a 10 px grid (px 707.5); ± is ~3 px","via":"harvest"}},{"id":"tdp","value":3.375,"unit":"in","source":{"type":"derived","expr":"{std.ar15.bolt_catch_slot_front_x}","via":"user"},"note":"The gap is the drawing's slot for the catch, at the left face."}],"adopt":{"from":"tdp","reason":"The drawing's slot (2026-10-03), which the reference CAD model has 0.007 further forward still. The photo's edge is the front boss's rounded edge, 0.027 behind it."}},"bolt_catch_boss_front_x":{"label":"Bolt catch bosses: the front boss's front edge, X","kind":"length","measurements":[{"id":"left","value":3.576,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"rifle frame from reviewed holes takedown (1242.5,489.5), pivot (223.5,488.5) = (0, 0), (6.375, 0) (159.8 px/in)","method":"edge picked on a 4x crop with a 10 px grid (px 671); ± is ~3 px","via":"harvest"}}]},"bolt_catch_boss_bottom_y":{"label":"Bolt catch bosses: their bottom edges, Y (they rise to the deck)","kind":"length","measurements":[{"id":"left","value":-0.05,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"rifle frame from reviewed holes takedown (1242.5,489.5), pivot (223.5,488.5) = (0, 0), (6.375, 0) (159.8 px/in)","method":"edge picked on a 4x crop with a 10 px grid (py 497.5); ± is ~3 px","via":"harvest"}}]},"width":{"label":"Receiver maximum width (Z)","kind":"length","measurements":[{"id":"ar15discounts","value":1.5,"unit":"in","stated":"Dimensions 7.7 × 1.5 × 4 in","source":{"type":"spec","publisher":"retailer","name":"ar15discounts (WooCommerce 'Additional information' field)","url":"https://ar15discounts.com/products/battle-arms-workhorse-forged-lower-receiver/","retrieved":"2026-09-30","via":"harvest"},"note":"L × W × H by convention. Its L and H match the corroborated outline (length 7.74 = rear 1.16 + front 6.57; height 3.94 = tower top 1.54 + lowest point 2.40), so this describes the part, not a shipping box. Probably the maximum width (tower ring or magwell flare); the body is narrower."}],"note":"No manufacturer figure and no top or end view of the Workhorse exists publicly (two discovery passes, 2026-09-30). Next corroboration: the Aero Gen 2 end views in the seed (a different forging, so check its side profile against the Workhorse first)."},"well_roll_crest_out":{"label":"The roll along the top of the magazine well's right wall, its crest from the centre plane (Z)","kind":"length","measurements":[{"id":"oblique","value":0.8,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bad-workhorse-lower a02a024b2be6 (the right side from above and a little ahead, 2000 px, serial WP14873), with 3f26be6b7eb5 (the pin-framed right side, serial WP01400) for where the hole is","scaleRef":"an affine camera fitted to the Army drawing's features on the oblique: the rims of the takedown, selector, hammer and trigger holes on the body's right face (std.ar15.lower_body_width / 2; the takedown's on its spotface's floor), the trigger guard's rear hole on its ear (std.ar15.trigger_guard_ears_width / 2), and the deck's edges across the receiver on seven columns (the body's two outer edges .880 apart, the fire-control pocket's two inner edges .690 apart): 248.9 px/in along, 240.4 up, and 61.0 px for an inch across (59.2 by the outer edges alone, 63.2 by the inner), rms 1.0 px","method":"The small blind hole in the roll (0.095 in across, level with the pivot pin) is at X 5.323, Y +0.024 on the side photo and at (1665.1, 943.6) px on the oblique: 22.1 px below where the camera puts that X and Y on the body's face, which is 0.363 in further out than that face. The same camera puts the mouth of the magazine catch's pocket (the drawing's X 3.291, Y -0.5635) 0.543 from the centre, which is the walls' face (0.549), and the pivot hole's rim on the lug's face within about 2 px up and 5 along (by eye on the overlay): neither was fitted. The fitted camera was drawn on the photo and looked at; the pivot lug's two ears' rims (.88 apart) show 16 px apart along and 53 up, and the hole in the roll stands 13 px along from where it would be on the centre plane, which agrees (0.7 to 0.8 in). The ± covers the scale across (± 0.028: which of the deck's edges set it), the hole's height on the side photo (± 0.006 in, which is ± 0.024 here: an inch of height reads as 3.9 in of this) and a pixel and a half on the oblique (± 0.024)","via":"harvest"},"note":"The hole is at the middle of the roll's height (well_roll_bottom_y to the deck), so this is taken as the crest. Two things agree with it: the one published width, a seller's 1.5 in (bad-workhorse-lower.width), less the left side as modelled (0.699: the wall, its band and the catch's boss) is 0.80; and the roll's front end (well_roll_front_x) stands where the Army's pivot pin has the flat on its head. The second oblique on file, 39f46bdefc1a, is not used: its marking can't be read as WORKHORSE, it has no rib down to a point, a second rib at the well's front and a doubled pivot ear (an altered image)."}]},"well_roll_bottom_y":{"label":"The roll along the top of the well's right wall, its lower edge (where its underside meets the wall's face), Y","kind":"length","measurements":[{"id":"right","value":-0.204,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"rifle frame from reviewed holes takedown (371.5,502.5), pivot (1380.5,505.5) = (0, 0), (6.375, 0) (158.3 px/in)","method":"brightness down ten columns from X 3.21 to 6.12 (7 px bands): the roll's underside is darkest at -0.14 to -0.17 and half-way back to the face's brightness at -0.203 to -0.208 on nine of them (the tenth is the rib's); the top edge on the same columns is 0.244 to 0.252, the drawing's deck","via":"harvest"},"note":"The ± is the run of the shading from the darkest row to the face's own brightness (0.05 in): where in it the roll ends isn't seen. fence_top_y (-0.22) is the same edge over the fence."}]},"well_roll_rear_x":{"label":"The roll along the top of the well's right wall, its rear end (the foot of its rounded end, on the body), X","kind":"length","measurements":[{"id":"right","value":2.905,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"rifle frame from reviewed holes takedown (371.5,502.5), pivot (1380.5,505.5) = (0, 0), (6.375, 0) (158.3 px/in)","method":"brightness along rows Y +0.12, +0.03 and -0.07 (5 px bands): the body's grey to 2.90 to 2.91, then the end's shadow (darkest at 2.96), the roll's own brightness by 3.09 to 3.12","via":"harvest"},"note":"The slope the fence's own rear edge was read from (fence_rear_x: 2.91 to 3.02) is this end's foot, lower down."}]},"well_roll_rear_round":{"label":"The roll along the top of the well's right wall, how far its rounded rear end runs before the roll is full","kind":"length","measurements":[{"id":"right","value":0.19,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"rifle frame from reviewed holes takedown (371.5,502.5), pivot (1380.5,505.5) = (0, 0), (6.375, 0) (158.3 px/in)","method":"the same three rows: from the end's foot at 2.905 to the roll's own brightness at 3.09 to 3.12","via":"harvest"},"note":"About the roll's own half height (0.226): its end is rounded as it is."}]},"well_roll_front_x":{"label":"The roll along the top of the well's right wall, its front end (a flat face beside the pivot lug), X","kind":"length","measurements":[{"id":"right","value":6.231,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"rifle frame from reviewed holes takedown (371.5,502.5), pivot (1380.5,505.5) = (0, 0), (6.375, 0) (158.3 px/in)","method":"brightness along rows Y +0.13, +0.03 and -0.06 (5 px bands): the roll ends at 1357.5, 1357.5 and 1358.5 px, one straight edge the height of the roll, the lug's lighter face ahead of it","via":"harvest"},"note":"0.144 in behind the pivot pin's axis. The Army's pivot pin has a flat on its head .1355 from its axis (8448621, rise-lpk.pivot_pin_head_d's note): this face is what the flat lies against."}]},"guard_ears_rear_x":{"label":"The trigger guard's rear ears, their rear face (where the grip's lug ends), X","kind":"length","measurements":[{"id":"tdp","value":1.175,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{std.ar15.receiver_rear_x} + {std.ar15.grip_lug_front_from_rear_face}","via":"user"},"note":"The Army's drawing: 2.300 ahead of the receiver's rear face."},{"id":"trace-right","value":1.169,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"a pinhole camera fitted to the rims of 7 holes, 5 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer, guard_rear, guard_front at the ledger's places; selector (its y left to the fit)): lens 24.1 ± 0.9 in from the centre plane, standing over x 4.18, y -1.77, the side leaning 9.3 ± 0.4° to the sensor with its bottom nearer and 0.1° with the picture's right nearer; 158.3 px/in on the near face at the lens's foot; rims within 0.86 px rms","method":"x_min in x [1.0, 1.4] in y [-2.3, -2.05] of the traced outline (tools/trace.py)","via":"harvest"},"note":"The rear ears' rear face, on the near ear's outside."},{"id":"trace-left","value":1.162,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"a pinhole camera fitted to the rims of 6 holes, 4 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer, guard_rear at the ledger's places; selector (its y left to the fit)): lens 23.9 ± 0.8 in from the centre plane, standing over x 3.82, y -2.09, the side leaning 10.6 ± 0.4° to the sensor with its bottom nearer and 0.8° with the picture's left nearer; 159.7 px/in on the near face at the lens's foot; rims within 0.72 px rms","method":"x_min in x [1.0, 1.4] in y [-2.3, -2.05] of the traced outline (tools/trace.py)","via":"harvest"},"note":"The rear ears' rear face, on the near ear's outside."}],"adopt":{"from":"tdp","reason":"The Army's drawing. Through their cameras the two photos read it 1.169 and 1.162: 0.006 and 0.013 behind, inside the ± of both (what the cameras' lean leaves open is 0.009 there). The two-pin frames had it at 1.14, and 1.127 to 1.132 in the outline traced from them: 0.045 behind by the frame, as at the guard's hole beside it (trigger_guard_rear_x). The outline, and the model built on it, have the right photo's."}},"grip_lug_face_from_pin":{"label":"The grip lug's sloped face, from the takedown pin's centre, square to the face","kind":"length","measurements":[{"id":"tdp","value":1.228,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{std.ar15.grip_lug_face_from_pin}","via":"user"},"note":"The Army's drawing: 1.228 ±.010."},{"id":"trace-right","value":1.225,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"a pinhole camera fitted to the rims of 7 holes, 5 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer, guard_rear, guard_front at the ledger's places; selector (its y left to the fit)): lens 24.1 ± 0.9 in from the centre plane, standing over x 4.18, y -1.77, the side leaning 9.3 ± 0.4° to the sensor with its bottom nearer and 0.1° with the picture's right nearer; 158.3 px/in on the near face at the lens's foot; rims within 0.86 px rms","method":"distance from the frame's origin to the straight line through the outline in x [0.3, 0.9] in y [-1.95, -1.55] (0.69 in of it, rms 0.001) of the traced outline (tools/trace.py)","via":"harvest"},"note":"The lug's sloped face, from the takedown pin's centre, square to the face."},{"id":"trace-left","value":1.217,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"a pinhole camera fitted to the rims of 6 holes, 4 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer, guard_rear at the ledger's places; selector (its y left to the fit)): lens 23.9 ± 0.8 in from the centre plane, standing over x 3.82, y -2.09, the side leaning 10.6 ± 0.4° to the sensor with its bottom nearer and 0.8° with the picture's left nearer; 159.7 px/in on the near face at the lens's foot; rims within 0.72 px rms","method":"distance from the frame's origin to the straight line through the outline in x [0.3, 0.9] in y [-1.95, -1.55] (0.69 in of it, rms 0.002) of the traced outline (tools/trace.py)","via":"harvest"},"note":"The lug's sloped face, from the takedown pin's centre, square to the face."}],"adopt":{"from":"tdp","reason":"The Army's drawing; through their cameras the two photos read 1.225 and 1.217."}},"grip_lug_face_angle":{"label":"The grip lug's sloped face, from the vertical","kind":"angle","measurements":[{"id":"tdp","value":60,"unit":"deg","pm":2,"source":{"type":"derived","expr":"{std.ar15.grip_lug_face_angle}","via":"user"},"note":"The Army's drawing: 60° ±2°."},{"id":"trace-right","value":60.093,"unit":"deg","pm":1.599,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"a pinhole camera fitted to the rims of 7 holes, 5 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer, guard_rear, guard_front at the ledger's places; selector (its y left to the fit)): lens 24.1 ± 0.9 in from the centre plane, standing over x 4.18, y -1.77, the side leaning 9.3 ± 0.4° to the sensor with its bottom nearer and 0.1° with the picture's right nearer; 158.3 px/in on the near face at the lens's foot; rims within 0.86 px rms","method":"angle from the vertical of the straight line through the outline in x [0.3, 0.9] in y [-1.95, -1.55] (0.69 in of it, rms 0.001) of the traced outline (tools/trace.py)","via":"harvest"}},{"id":"trace-left","value":59.909,"unit":"deg","pm":1.584,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"a pinhole camera fitted to the rims of 6 holes, 4 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer, guard_rear at the ledger's places; selector (its y left to the fit)): lens 23.9 ± 0.8 in from the centre plane, standing over x 3.82, y -2.09, the side leaning 10.6 ± 0.4° to the sensor with its bottom nearer and 0.8° with the picture's left nearer; 159.7 px/in on the near face at the lens's foot; rims within 0.72 px rms","method":"angle from the vertical of the straight line through the outline in x [0.3, 0.9] in y [-1.95, -1.55] (0.69 in of it, rms 0.002) of the traced outline (tools/trace.py)","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The Army's drawing; through their cameras the two photos read 60.1 and 59.9 degrees."}},"rear_underside_arc_r":{"label":"The rear underside (from under the buffer tower down to the grip's seat), its arc along the centre plane: radius about the reference CAD model's centre","kind":"length","measurements":[{"id":"trace-right","value":0.716,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","scaleRef":"a pinhole camera fitted to the rims of 7 holes, 5 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer, guard_rear, guard_front at the ledger's places; selector (its y left to the fit)): lens 24.1 ± 0.9 in from the centre plane, standing over x 4.18, y -1.77, the side leaning 9.3 ± 0.4° to the sensor with its bottom nearer and 0.1° with the picture's right nearer; 158.3 px/in on the near face at the lens's foot; rims within 0.86 px rms","method":"mean distance of the outline in x [-0.88, -0.36] in y [-1.02, -0.54] from ({std.ar15.rear_underside_arc_center_x}, {std.ar15.deck_y} - {std.ar15.grip_seat_below_deck} - {std.ar15.rear_underside_arc_center_below_seat}) = (-1.0238, -1.2623); it keeps within 0.003 (1σ) of that, 0.712 to 0.725 of the traced outline (tools/trace.py)","via":"harvest"},"note":"The rear underside along the centre plane, about the centre the reference CAD model's has (std.ar15.rear_underside_arc_center_x, _below_seat): read on the round's lowest line, which is what shows from a lens ahead of it if the underside is the half-round across that its rear end is."},{"id":"trace-left","value":0.723,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/bad-workhorse-lower 6d4ee1a1b3b8 (left side, independent photo (Arsenal Engineering))","scaleRef":"a pinhole camera fitted to the rims of 6 holes, 4 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer, guard_rear at the ledger's places; selector (its y left to the fit)): lens 23.9 ± 0.8 in from the centre plane, standing over x 3.82, y -2.09, the side leaning 10.6 ± 0.4° to the sensor with its bottom nearer and 0.8° with the picture's left nearer; 159.7 px/in on the near face at the lens's foot; rims within 0.72 px rms","method":"mean distance of the outline in x [-0.88, -0.36] in y [-1.02, -0.54] from ({std.ar15.rear_underside_arc_center_x}, {std.ar15.deck_y} - {std.ar15.grip_seat_below_deck} - {std.ar15.rear_underside_arc_center_below_seat}) = (-1.0238, -1.2623); it keeps within 0.003 (1σ) of that, 0.717 to 0.733 of the traced outline (tools/trace.py)","via":"harvest"},"note":"The rear underside along the centre plane, about the centre the reference CAD model's has (std.ar15.rear_underside_arc_center_x, _below_seat): read on the round's lowest line, which is what shows from a lens ahead of it if the underside is the half-round across that its rear end is."}],"adopt":{"from":"trace-right","reason":"The photo the outline is traced from; the left photo's, through its own camera, agrees within 0.007."},"note":"How full the underside is behind a grip: a beavertail's saddle has to clear it. About the centre the reference model's arc has (std.ar15.rear_underside_arc_center_x, 0.1928 below the seat) the Workhorse's underside keeps one distance within 0.003 from X -0.88 to -0.36, so it is an arc about that centre too: 0.03 fuller than the model's 0.750. Read on the round's lowest line, which is the edge a lens ahead of it sees if the underside is half-round across there as it is at the rear face (where reading it so stands the rear face upright on the Army drawing's -1.125, in both photos)."}}},{"subject":"bca-556-16-mid-barrel","title":"Bear Creek Arsenal BC-15 5.56 NATO, 16\" Parkerized M4 Barrel, 1:7 Twist, Mid-Length Gas System (1343-B556MM41617(P))","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"bca","value":1.75,"unit":"lb","pm":0.005,"stated":"Weight (lbs) 1.750000","source":{"type":"spec","publisher":"manufacturer","name":"Bear Creek Arsenal, BC-15 5.56 NATO, 16\" Parkerized M4 Barrel, 1:7 Twist, Mid-Length Gas System (1343-B556MM41617(P)), Specs","url":"https://www.bearcreekarsenal.com/556-16-parkerized-m4-barrel-1-7-twist-mid-length.html","retrieved":"2026-10-05","via":"harvest"},"note":"The shop's weight field (the six decimals are its number format, read as 1.75): it doesn't say whether it is the barrel bare or packed."},{"id":"redcon1","value":29,"unit":"oz","pm":0.5,"stated":"Weight: 29 oz","source":{"type":"spec","publisher":"retailer","name":"Redcon1 Tactical, Bear Creek Arsenal 16\" Contour 4150 Parkerized 5.56 Mid-Length 1:7 Barrel (Mfr Part 1343-B556MM41617(P))","url":"https://redcon1tactical.com/bear-creek-arsenal-16-contour-4150-parkerized-5-56-mid-length-1-7-barrel.html","retrieved":"2026-10-05","via":"harvest"}},{"id":"ar15discounts","value":29.008,"unit":"oz","pm":0.008,"stated":"Weight 29.008 oz","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, 16\" 5.56 NATO 1:7 Twist Mid-Length Parkerized Barrel - 1343-B556MM41617(P) (sold under its NBS label; MPN 1343-B556MM41617(P)), Additional information","url":"https://ar15discounts.com/products/16-5-56-nato-17-twist-mid-length-parkerized-barrel/","retrieved":"2026-10-05","via":"harvest"},"note":"Beside \"Dimensions 18 × 3 × 3 in\", a shipping box. 29.008 oz is 1.813 lb to the ounce's thousandth: a pound figure converted (the ± is that rounding), and 29 oz to three places of a pound."},{"id":"dirty-bird","value":29.008,"unit":"oz","pm":0.008,"stated":"Weight 29.008 oz","source":{"type":"spec","publisher":"retailer","name":"Dirty Bird Industries, 16\" 5.56 NATO 1:7 Twist Mid-Length Parkerized Barrel - 1343-B556MM41617(P), Additional information","url":"https://dirtybirdusa.com/collections/barrel/products/bca-16-5-56-nato-1-7-twist-mid-length-parkerized-barrel","retrieved":"2026-10-05","via":"harvest"},"note":"The same listing as AR15Discounts' (its SKU 1374, its text, its figures): one source, not two."},{"id":"right-to-bear","value":1.9,"unit":"lb","pm":0.05,"stated":"Weight - 1.9 Pounds","source":{"type":"spec","publisher":"retailer","name":"Right To Bear, Bear Creek 16 Inch M4 Mid-Length Barrel 5.56 (SKU 1343-B556MM41617)","url":"https://www.righttobear.com/bear-creek-16-m4-mid-barrel-5-56-1343-b556mm41617/","retrieved":"2026-10-05","via":"harvest"}}],"adopt":{"from":"redcon1","reason":"Two listings give it (AR15Discounts' figure is the same 29 oz), and the barrel's own shape supports it: the model turned from its photo is 6.99 cubic inches with only its bore and its port cut, 31.3 oz at the density on file for a barrel steel (std.density.stainless_416; a chrome-moly steel is within 2% of it), and the chamber and the extension's recess for the bolt, which the model doesn't cut, come off that. Its maker's 1.75 lb (28 oz) is 3.5% under and Right To Bear's 1.9 lb (30.4 oz) 4.8% over: both stay as the range."},"note":"Four figures on five pages, none with a method. Primary Arms, where this barrel was chosen, states none. The maker's own is the lowest and isn't adopted: it is its shop's weight field, a quarter-pound figure, and the barrel's volume says more (the adoption's reason)."},"length":{"label":"Barrel length as its maker states it","kind":"length","measurements":[{"id":"bca","value":16,"unit":"in","pm":0.1,"stated":"Barrel Length 16","source":{"type":"spec","publisher":"manufacturer","name":"Bear Creek Arsenal, BC-15 5.56 NATO, 16\" Parkerized M4 Barrel, 1:7 Twist, Mid-Length Gas System (1343-B556MM41617(P)), Specs","url":"https://www.bearcreekarsenal.com/556-16-parkerized-m4-barrel-1-7-twist-mid-length.html","retrieved":"2026-10-05","via":"harvest"}},{"id":"primary-arms","value":16,"unit":"in","pm":0.1,"stated":"Barrel Length 16","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Bear Creek Arsenal 5.56 AR-15 Barrel - Mid-Length - M4 - 16\" (1343-B556MM41617-P), Specifications","url":"https://www.primaryarms.com/bear-creek-arsenal-16in-5-56-nato-1-7-mid-length-ar-15-barrel-parkerized","retrieved":"2026-10-05","via":"harvest"}}],"adopt":{"from":"bca","reason":"The maker's page; the seller's is the same figure."},"note":"Nominal, and Bear Creek doesn't say between which points. Taken as the barrel's own length, breech face to muzzle, as the catalog's two other 16 in barrels are: a mid-length chart on file dimensions its barrel so (14.500 from the tenon's end). The Army's own convention is from the closed bolt's face, which stands 0.126 behind the breech face (bolt_face_behind_breech): its 20 in barrel is 19.884 ±.015 on drawing 8448549. By that convention this barrel would be 0.126 shorter; the ± is taken to cover it. Its photo favours the breech face: at the scale its .750 journal gives it reads 16.66 between its end faces, 1.0% over this reading's 16.50 (the 16 and the extension's 0.501 behind the breech face) and 1.7% over the other's 16.375. Primary Arms and Right To Bear state the same 16."},"journal_od":{"label":"The gas block journal's diameter","kind":"length","measurements":[{"id":"bca","value":0.75,"unit":"in","pm":0.0005,"stated":"Gas Block System 0.750","source":{"type":"spec","publisher":"manufacturer","name":"Bear Creek Arsenal, BC-15 5.56 NATO, 16\" Parkerized M4 Barrel, 1:7 Twist, Mid-Length Gas System (1343-B556MM41617(P)), Specs","url":"https://www.bearcreekarsenal.com/556-16-parkerized-m4-barrel-1-7-twist-mid-length.html","retrieved":"2026-10-05","via":"harvest"}},{"id":"primary-arms","value":0.75,"unit":"in","pm":0.0005,"stated":"Gas Seat Diameter .750","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Bear Creek Arsenal 5.56 AR-15 Barrel - Mid-Length - M4 - 16\" (1343-B556MM41617-P), Specifications","url":"https://www.primaryarms.com/bear-creek-arsenal-16in-5-56-nato-1-7-mid-length-ar-15-barrel-parkerized","retrieved":"2026-10-05","via":"harvest"}}],"adopt":{"from":"bca","reason":"The maker's page; the seller's is the same figure."},"note":"Right To Bear (\"Gas Block Journal - .750\\\"\"), Redcon1 (\"Gas Block Size: 0.750\\\"\") and AR15Discounts (\"Gas Block Journal 0.75\") say the same."},"extension_behind_breech":{"label":"The barrel extension's rear face behind the barrel's breech face","kind":"length","measurements":[{"id":"photo","value":0.507,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.flange_front_x} - {.extension_rear_x} - {.tenon_length}","via":"harvest"},"note":"The flange's front face ahead of the extension's rear face, less the tenon: the rear face is the traced outline's, the flange's thickness the adopted one."},{"id":"model","value":0.501,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{std.ar15.barrel_extension_behind_breech}","via":"harvest"},"note":"The reference CAD set's Barrel_Extension.step, 1.121 from its front face to its rear end, less the .620 tenon: the readings and their sources are in the standard's ledger (std.ar15.barrel_extension_length, std.ar15.barrel_tenon_length)."}],"adopt":{"from":"model","reason":"One figure for every barrel on this extension (Aero's and BCM's use the same), read face by face off the CAD set; this barrel's own photo gives 0.507 with the flange at the CAD set's thickness, inside its ±."},"note":"One extension for the catalog's three 5.56 barrels (2026-10-05, the review of the catalog's models): the reference CAD set's, 1.121 long, less the .620 tenon (tenon_length), as BCM's barrel has it. No callout on the Army's sheets gives it: on the assembly drawing's Section A-A the extension is drawn broken off behind its locking face, its own drawing (8448550) isn't in the package, and Aero's barrel had 0.46 scaled off the 1/1 view, whose own callouts put its scale anywhere within 8% (that reading stays in that barrel's ledger). Until 2026-10-05 this barrel's own photo was adopted at 0.57, by a flange read 0.191 thick (flange_front_x): that put its breech 0.07 in ahead of BCM's and its muzzle 0.06 further out than a 16 in barrel on the same extension. The photo's reading is now made with the flange the CAD set's, and agrees."},"bolt_face_behind_breech":{"label":"The closed bolt's face behind the barrel's breech face","kind":"length","measurements":[{"id":"tdp","value":0.126,"unit":"in","pm":0.007,"stated":"1.6206 REF and .283 +.006 (8448548); 1.4636 MIN (the chamber print, bolt face to the .3300 datum)","source":{"type":"standard","doc":"US Army TDP drawing 8448548 (Barrel and Barrel Extension Assembly), Section A-A: the .3300 DIA DATUM 1.6206 REF from the extension's locking face, the breech face .283 +.006 from it; with Pacific Tool's chamber print 8008, '5.56 Nato Military' (10/31/05, citing military prints 8448649, 8448549, 8448550; 5.56x45mm_Chamber_Schematic.jpg in the user's TDP folder), 1.4636 MIN from the bolt face to that datum; user-supplied scans, PDF page 212","via":"user"},"note":"The datum is 1.6206 - .283 = 1.3376 ahead of the breech face, and 1.4636 ahead of the bolt's face."}],"note":"Where a barrel's length is measured from by the Army's convention: not used for this barrel's own length (length's note), kept because it sizes the question."},"tenon_length":{"label":"The barrel's tenon: its breech face behind the shoulder the extension's front face seats on","kind":"length","measurements":[{"id":"tdp","value":0.62,"unit":"in","pm":0.001,"source":{"type":"derived","expr":"{std.ar15.barrel_tenon_length}","via":"user"},"note":"The Army's drawing 8448549, .620 ±.001: in the standard's ledger since 2026-10-05."}]},"overall_length":{"label":"End to end: the extension's rear face to the muzzle face","kind":"length","measurements":[{"id":"published","value":16.501,"unit":"in","pm":0.1,"source":{"type":"derived","expr":"{.length} + {.extension_behind_breech}","via":"harvest"}}],"note":"The length the photo's lengths are scaled to: the published 16 from the breech face, plus the extension behind it (16.57 until 2026-10-05, with this barrel's own reading of its flange). At the scale its .750 journal gives, the photo reads 16.66 between its end faces, 1.0% more: inside what the yaw's cosine and a pixel of the journal's width leave open, and the ± here covers it."},"handguard_section_od":{"label":"The diameter of the long section under the handguard, between the chamber's taper and the gas block's collar","kind":"length","measurements":[{"id":"photo","value":0.6976,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/bca-556-16-mid-barrel eff6b190e339 (Primary Arms 1343-B556MM41617-P_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"its gas block journal's width on the same photo as the published .750 (journal_od), edges read at 235 of 255","method":"its width against the journal's, each column's scale taken from the line through this section's own widths (tools/trace.py, tube): the value at which the traced outline's journal (x 9.75 to 11.1 behind the collar) reads 0.750","via":"harvest"}}],"note":"The trace's tube. Its width along the photo is a line, 84.0 px at column 1100 to 85.2 at 1780 (the photo's yaw); the journal ahead of it reads 89.3 px where that line reads 82.9. Set so that the traced outline's journal reads the published .750: the journal is the scale, this section carries it along the photo."},"extension_rear_x":{"label":"The barrel extension's rear face, from the flange's rear face (negative: inside the receiver)","kind":"length","measurements":[{"id":"photo","value":-0.996,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bca-556-16-mid-barrel eff6b190e339 (Primary Arms 1343-B556MM41617-P_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"scale from bca-556-16-mid-barrel.handguard_section_od = 0.6976 in, the tube's own width column by column: 84.0 px over columns 1080–1200, 84.1 px over columns 1200–1400, 84.6 px over columns 1400–1600, 85.2 px over columns 1660–1790; a line through them (rms 0.19 px) changes +1.7% from column 1080 to 1790, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 120.1 px/in there. The axis is the tube's centre line (tilt +0.52°, rms 0.08 px). Lengths then scaled by 0.9904 so that the end faces are bca-556-16-mid-barrel.overall_length = 16.501 in apart: at the tube's scale they read 16.662 (+1.0%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.046 in over radius 0.190 (rms 0.004), the rear end's rim sags 0.036 in over radius 0.300 (rms 0.003)","method":"−x_min in y [0.53, 0.6] of the traced outline (tools/trace.py); the flange's rear face, which seats on the receiver's front face, from the extension's rear face","via":"harvest"}}],"note":"The rear face is taken behind its rim's arc (0.036 in of sag: the silhouette's tip is the face's near rim). The reference CAD set's extension has 0.990 here; Aero's barrel reads 0.98 and BCM's 0.984 by their own photos."},"flange_front_x":{"label":"The flange's front face, which is the extension's front end, from the flange's rear face","kind":"length","measurements":[{"id":"photo","value":0.19,"unit":"in","pm":0.023,"source":{"type":"photo","photo":"references/bca-556-16-mid-barrel eff6b190e339 (Primary Arms 1343-B556MM41617-P_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"scale from bca-556-16-mid-barrel.handguard_section_od = 0.6976 in, the tube's own width column by column: 84.0 px over columns 1080–1200, 84.1 px over columns 1200–1400, 84.6 px over columns 1400–1600, 85.2 px over columns 1660–1790; a line through them (rms 0.19 px) changes +1.7% from column 1080 to 1790, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 120.1 px/in there. The axis is the tube's centre line (tilt +0.52°, rms 0.08 px). Lengths then scaled by 0.9904 so that the end faces are bca-556-16-mid-barrel.overall_length = 16.501 in apart: at the tube's scale they read 16.662 (+1.0%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.046 in over radius 0.190 (rms 0.004), the rear end's rim sags 0.036 in over radius 0.300 (rms 0.003)","method":"(x_max in y [0.53, 0.6]) − (x_min in y [0.53, 0.6]) of the traced outline (tools/trace.py); the flange, rear face to front face","via":"harvest"}},{"id":"model","value":0.131,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.ar15.barrel_extension_flange_thickness}","via":"user"},"note":"The reference CAD set's Barrel_Extension.step, its planes across its axis: the reading and its source are in the standard's ledger since 2026-10-05."}],"adopt":{"from":"model","reason":"The photo's 0.19 spans the flange's two corners, each its rim's arc seen from off square, and the same outline's flat top is 0.09 to 0.12; the CAD set's faces are between the two readings. And it is the extension the three 5.56 barrels share (extension_behind_breech)."},"note":"The flange's thickness. Its front face seats on the shoulder of the barrel's tenon, .620 ahead of the breech face (tenon_length). The photo's reading is across the flange where the outline stands over 0.53 in from the axis, which takes in both of its corners: the lens sees this end from about 7° off square, so each corner is its rim's arc, and the outline's own flat top is 0.09 to 0.12 long (x 1.04 to 1.12 or 1.16 from the rear face). BCM's flange reads 0.095 between its corners the same way, Aero's 0.11 to 0.13; the CAD set's faces are 0.131 apart."},"flange_od":{"label":"The barrel extension's flange, its diameter","kind":"length","measurements":[{"id":"photo","value":1.175,"unit":"in","pm":0.027,"source":{"type":"photo","photo":"references/bca-556-16-mid-barrel eff6b190e339 (Primary Arms 1343-B556MM41617-P_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"scale from bca-556-16-mid-barrel.handguard_section_od = 0.6976 in, the tube's own width column by column: 84.0 px over columns 1080–1200, 84.1 px over columns 1200–1400, 84.6 px over columns 1400–1600, 85.2 px over columns 1660–1790; a line through them (rms 0.19 px) changes +1.7% from column 1080 to 1790, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 120.1 px/in there. The axis is the tube's centre line (tilt +0.52°, rms 0.08 px). Lengths then scaled by 0.9904 so that the end faces are bca-556-16-mid-barrel.overall_length = 16.501 in apart: at the tube's scale they read 16.662 (+1.0%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.046 in over radius 0.190 (rms 0.004), the rear end's rim sags 0.036 in over radius 0.300 (rms 0.003)","method":"height of the traced outline (tools/trace.py); the silhouette's widest: the flange","via":"harvest"}}]},"extension_od":{"label":"The barrel extension's diameter behind its flange","kind":"length","measurements":[{"id":"photo","value":0.99,"unit":"in","pm":0.027,"source":{"type":"photo","photo":"references/bca-556-16-mid-barrel eff6b190e339 (Primary Arms 1343-B556MM41617-P_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"scale from bca-556-16-mid-barrel.handguard_section_od = 0.6976 in, the tube's own width column by column: 84.0 px over columns 1080–1200, 84.1 px over columns 1200–1400, 84.6 px over columns 1400–1600, 85.2 px over columns 1660–1790; a line through them (rms 0.19 px) changes +1.7% from column 1080 to 1790, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 120.1 px/in there. The axis is the tube's centre line (tilt +0.52°, rms 0.08 px). Lengths then scaled by 0.9904 so that the end faces are bca-556-16-mid-barrel.overall_length = 16.501 in apart: at the tube's scale they read 16.662 (+1.0%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.046 in over radius 0.190 (rms 0.004), the rear end's rim sags 0.036 in over radius 0.300 (rms 0.003)","method":"height (tooth tops, max over 0.05 in windows) along x [0.25, 0.85] of the traced outline (tools/trace.py); the extension behind its flange","via":"harvest"}},{"id":"tdp","value":0.999,"unit":"in","pm":0.001,"stated":"DIAMETER NOT TO EXCEED .9990 FOR THIS LENGTH AFTER ASSEMBLY AND BEFORE FINISH","source":{"type":"standard","doc":"US Army TDP drawing 8448548 (Barrel and Barrel Extension Assembly); user-supplied scan (Distribution Statement F, Colt proprietary notice), PDF page 212: the main view","via":"user"},"note":"A limit, on the Army's barrel: an extension is made just under it."}],"adopt":{"from":"photo","reason":"The outline's own reading, which is what is drawn; the Army's limit is 0.009 over it, inside the reading's ±."},"note":"It goes into the receiver's 1.000 bore. The photo reads it 0.9% under the Army's limit, inside its ±: a check of the photo's scale at the breech end, where the tube's line is carried 250 columns past its last station."},"chamber_od":{"label":"The diameter of the chamber section, ahead of the flange","kind":"length","measurements":[{"id":"photo","value":0.981,"unit":"in","pm":0.027,"source":{"type":"photo","photo":"references/bca-556-16-mid-barrel eff6b190e339 (Primary Arms 1343-B556MM41617-P_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"scale from bca-556-16-mid-barrel.handguard_section_od = 0.6976 in, the tube's own width column by column: 84.0 px over columns 1080–1200, 84.1 px over columns 1200–1400, 84.6 px over columns 1400–1600, 85.2 px over columns 1660–1790; a line through them (rms 0.19 px) changes +1.7% from column 1080 to 1790, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 120.1 px/in there. The axis is the tube's centre line (tilt +0.52°, rms 0.08 px). Lengths then scaled by 0.9904 so that the end faces are bca-556-16-mid-barrel.overall_length = 16.501 in apart: at the tube's scale they read 16.662 (+1.0%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.046 in over radius 0.190 (rms 0.004), the rear end's rim sags 0.036 in over radius 0.300 (rms 0.003)","method":"height (tooth tops, max over 0.05 in windows) along x [1.25, 1.65] of the traced outline (tools/trace.py); the chamber section between the flange and its taper","via":"harvest"}},{"id":"tdp","value":0.98,"unit":"in","pm":0.0005,"stated":".9800 ±.0005 ANGULAR DEVIATION CONTROL DIAMETER","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2; user-supplied scan (Distribution Statement F, Colt proprietary notice), PDF page 213: the main view","via":"user"},"note":"The Army's barrel behind its taper; a commercial barrel is turned to the same seat for the barrel nut and the handguard's cap."}],"adopt":{"from":"photo","reason":"The outline's own reading, which is what is drawn; the Army's figure is a thousandth under it."},"note":"The photo reads the Army's figure within a thousandth: the second check of its scale at the breech end, and independent of the first."},"collar_od":{"label":"The diameter of the collar the gas block stops against","kind":"length","measurements":[{"id":"photo","value":0.979,"unit":"in","pm":0.027,"source":{"type":"photo","photo":"references/bca-556-16-mid-barrel eff6b190e339 (Primary Arms 1343-B556MM41617-P_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"scale from bca-556-16-mid-barrel.handguard_section_od = 0.6976 in, the tube's own width column by column: 84.0 px over columns 1080–1200, 84.1 px over columns 1200–1400, 84.6 px over columns 1400–1600, 85.2 px over columns 1660–1790; a line through them (rms 0.19 px) changes +1.7% from column 1080 to 1790, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 120.1 px/in there. The axis is the tube's centre line (tilt +0.52°, rms 0.08 px). Lengths then scaled by 0.9904 so that the end faces are bca-556-16-mid-barrel.overall_length = 16.501 in apart: at the tube's scale they read 16.662 (+1.0%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.046 in over radius 0.190 (rms 0.004), the rear end's rim sags 0.036 in over radius 0.300 (rms 0.003)","method":"height (tooth tops, max over 0.05 in windows) along x [9.15, 9.6] of the traced outline (tools/trace.py); the collar behind the gas block journal","via":"harvest"}}]},"journal_shoulder_x":{"label":"The collar's front face, where the gas block journal begins, ahead of the flange's rear face","kind":"length","measurements":[{"id":"photo","value":8.846,"unit":"in","pm":0.095,"source":{"type":"photo","photo":"references/bca-556-16-mid-barrel eff6b190e339 (Primary Arms 1343-B556MM41617-P_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"scale from bca-556-16-mid-barrel.handguard_section_od = 0.6976 in, the tube's own width column by column: 84.0 px over columns 1080–1200, 84.1 px over columns 1200–1400, 84.6 px over columns 1400–1600, 85.2 px over columns 1660–1790; a line through them (rms 0.19 px) changes +1.7% from column 1080 to 1790, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 120.1 px/in there. The axis is the tube's centre line (tilt +0.52°, rms 0.08 px). Lengths then scaled by 0.9904 so that the end faces are bca-556-16-mid-barrel.overall_length = 16.501 in apart: at the tube's scale they read 16.662 (+1.0%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.046 in over radius 0.190 (rms 0.004), the rear end's rim sags 0.036 in over radius 0.300 (rms 0.003)","method":"(x_max in x [9.0, 10.6] in y [0.41, 0.47]) − (x_min in y [0.53, 0.6]) of the traced outline (tools/trace.py); the collar's front face, where the journal begins, ahead of the flange's rear face","via":"harvest"}}],"note":"A gas block stops against it. From the flange's front face (the tenon's shoulder) it is 8.72; a mid-length chart on file has 8.750 there (AR-15_M4_Barrel_Dimensions.jpg: a third-party illustration of a 14.5 in barrel)."},"shoulder_x":{"label":"The muzzle shoulder ahead of the flange's rear face","kind":"length","measurements":[{"id":"photo","value":14.911,"unit":"in","pm":0.151,"source":{"type":"photo","photo":"references/bca-556-16-mid-barrel eff6b190e339 (Primary Arms 1343-B556MM41617-P_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"scale from bca-556-16-mid-barrel.handguard_section_od = 0.6976 in, the tube's own width column by column: 84.0 px over columns 1080–1200, 84.1 px over columns 1200–1400, 84.6 px over columns 1400–1600, 85.2 px over columns 1660–1790; a line through them (rms 0.19 px) changes +1.7% from column 1080 to 1790, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 120.1 px/in there. The axis is the tube's centre line (tilt +0.52°, rms 0.08 px). Lengths then scaled by 0.9904 so that the end faces are bca-556-16-mid-barrel.overall_length = 16.501 in apart: at the tube's scale they read 16.662 (+1.0%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.046 in over radius 0.190 (rms 0.004), the rear end's rim sags 0.036 in over radius 0.300 (rms 0.003)","method":"(x_max in y [0.29, 0.35]) − (x_min in y [0.53, 0.6]) of the traced outline (tools/trace.py); where the silhouette drops to the thread, ahead of the flange's rear face","via":"harvest"}}],"note":"Where the thread begins and a muzzle device seats. An independent look at the same place on another 16 in barrel: Aero's photo of its complete upper (references/aero-m4e1-complete-upper-16-mid-r-one-15 0a6c8a661544), framed by its two lug holes and scaled by its rail's teeth (14.59 px a tooth at the receiver, 14.38 at the handguard's front), has its A2 flash hider's front face 16.83 ahead of the receiver's front face, so its shoulder 14.98 ± 0.1 (the device's 1.75 and a washer behind it, 0.10 allowed for it); that barrel's own photo has 14.89, and this barrel's is 14.91 (14.974 until 2026-10-05, when its length was scaled to an extension 0.07 longer behind the breech)."},"thread_length":{"label":"The muzzle thread's length, shoulder to muzzle face","kind":"length","measurements":[{"id":"photo","value":0.595,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bca-556-16-mid-barrel eff6b190e339 (Primary Arms 1343-B556MM41617-P_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"scale from bca-556-16-mid-barrel.handguard_section_od = 0.6976 in, the tube's own width column by column: 84.0 px over columns 1080–1200, 84.1 px over columns 1200–1400, 84.6 px over columns 1400–1600, 85.2 px over columns 1660–1790; a line through them (rms 0.19 px) changes +1.7% from column 1080 to 1790, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 120.1 px/in there. The axis is the tube's centre line (tilt +0.52°, rms 0.08 px). Lengths then scaled by 0.9904 so that the end faces are bca-556-16-mid-barrel.overall_length = 16.501 in apart: at the tube's scale they read 16.662 (+1.0%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.046 in over radius 0.190 (rms 0.004), the rear end's rim sags 0.036 in over radius 0.300 (rms 0.003)","method":"(the max end's face: the silhouette's tip at 16.548 less its rim's arc, 0.046 in of sag at radius 0.19 (the end is seen from 13.5° off square; arc fitted over 121 rows, rms 0.004)) − (x_max in y [0.29, 0.35]) of the traced outline (tools/trace.py); the muzzle face, behind its rim's arc, ahead of the shoulder","via":"harvest"}},{"id":"tdp","value":0.63,"unit":"in","pm":0.005,"stated":".63","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2; user-supplied scan (Distribution Statement F, Colt proprietary notice), PDF page 213: the main view, the shoulder to the muzzle","via":"user"},"note":"The Army's barrel for the same 1/2-28 thread."}],"adopt":{"from":"photo","reason":"This barrel's own photo. A device's limit is compared with it: the A2's threaded bore is .68 deep, and either figure is inside it."},"note":"The photo's ± is set by hand: the tool sums each end's whole scale uncertainty, and the two ends are 0.6 in apart on one scale (two edges at ± 1.5 px, and the muzzle face behind its rim's arc: ± 0.03). The Army's barrel has .63; this one's photo reads 0.035 less, at the edge of its ±."},"muzzle_od":{"label":"The diameter behind the muzzle thread","kind":"length","measurements":[{"id":"photo","value":0.744,"unit":"in","pm":0.026,"source":{"type":"photo","photo":"references/bca-556-16-mid-barrel eff6b190e339 (Primary Arms 1343-B556MM41617-P_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"scale from bca-556-16-mid-barrel.handguard_section_od = 0.6976 in, the tube's own width column by column: 84.0 px over columns 1080–1200, 84.1 px over columns 1200–1400, 84.6 px over columns 1400–1600, 85.2 px over columns 1660–1790; a line through them (rms 0.19 px) changes +1.7% from column 1080 to 1790, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 120.1 px/in there. The axis is the tube's centre line (tilt +0.52°, rms 0.08 px). Lengths then scaled by 0.9904 so that the end faces are bca-556-16-mid-barrel.overall_length = 16.501 in apart: at the tube's scale they read 16.662 (+1.0%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.046 in over radius 0.190 (rms 0.004), the rear end's rim sags 0.036 in over radius 0.300 (rms 0.003)","method":"height (tooth tops, max over 0.05 in windows) along x [15.0, 15.7] of the traced outline (tools/trace.py); the section behind the muzzle shoulder","via":"harvest"}}]},"thread_od":{"label":"The muzzle thread over its crests","kind":"length","measurements":[{"id":"photo","value":0.496,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/bca-556-16-mid-barrel eff6b190e339 (Primary Arms 1343-B556MM41617-P_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"scale from bca-556-16-mid-barrel.handguard_section_od = 0.6976 in, the tube's own width column by column: 84.0 px over columns 1080–1200, 84.1 px over columns 1200–1400, 84.6 px over columns 1400–1600, 85.2 px over columns 1660–1790; a line through them (rms 0.19 px) changes +1.7% from column 1080 to 1790, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 120.1 px/in there. The axis is the tube's centre line (tilt +0.52°, rms 0.08 px). Lengths then scaled by 0.9904 so that the end faces are bca-556-16-mid-barrel.overall_length = 16.501 in apart: at the tube's scale they read 16.662 (+1.0%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.046 in over radius 0.190 (rms 0.004), the rear end's rim sags 0.036 in over radius 0.300 (rms 0.003)","method":"height (tooth tops, max over 0.05 in windows) along x [16.0, 16.35] of the traced outline (tools/trace.py); the thread's silhouette over its crests","via":"harvest"}},{"id":"tdp","value":0.49565,"unit":"in","pm":0.00325,"stated":"1/2-28 UNEF-2A MAJOR DIA .4989/.4924","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2; user-supplied scan (Distribution Statement F, Colt proprietary notice), PDF page 213: Section M-M","via":"user"},"note":"The middle of the two limits, ± half their spread."}],"adopt":{"from":"photo","reason":"The outline's own reading, which is what is drawn; it is inside the drawing's limits."},"note":"The check of the photo's scale at the muzzle end, 950 columns ahead of the tube's first station: the thread is 1/2-28 by its maker, and its silhouette reads inside the Army's limits for that thread."},"gas_port_ahead_of_shoulder":{"label":"The gas port ahead of the collar's front face","kind":"length","measurements":[{"id":"tdp","value":0.295,"unit":"in","pm":0.005,"stated":".295","source":{"type":"standard","doc":"US Army TDP drawing 8448548 (Barrel and Barrel Extension Assembly); user-supplied scan (Distribution Statement F, Colt proprietary notice), PDF page 212: the main view, the gas port from the shoulder the front sight stops against (datum A)","via":"user"},"note":"The Army's barrel: what a gas block's own port is placed for."},{"id":"photo","value":0.275,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bca-556-16-mid-barrel 53fbcf1e58d8 (Primary Arms 1343-B556MM41617-P_01: three-quarter view, the breech at the top left, 2200 x 1467)","scaleRef":"two ways on that photo: the journal's width there (103 px, the published .750) with the view's angle from the collar's rim (an ellipse 23 by 65 px: 20.5 degrees), and the collar's own length there (88 px along the axis, 0.62 in in the side trace)","method":"the port's centre (1234, 739) along the axis from the collar's front face on the port's own generator: 37 px. 0.288 by the journal's width, 0.263 by the collar's length; points picked by eye on a 5x crop","via":"harvest"}},{"id":"chart","value":0.3,"unit":"in","pm":0.005,"stated":"0.300","source":{"type":"spec","publisher":"unknown","name":"AR-15_M4_Barrel_Dimensions.jpg in the user's TDP folder (Spec_Sheets): a third-party illustration of a 14.5 in mid-length barrel, no drawing number","via":"user"}}],"adopt":{"from":"tdp","reason":"The Army's drawing, which gas blocks are made to; this barrel's own photo reads 0.02 less, inside its ±, and the chart 0.005 more."},"note":"The side photo doesn't show the port (it is on the far side; the dimple opposite it shows on the lower edge, 0.23 ahead of the collar). Primary Arms' three-quarter photo does."},"gas_port_x":{"label":"The gas port ahead of the flange's rear face","kind":"length","measurements":[{"id":"photo","value":9.141,"unit":"in","pm":0.1,"source":{"type":"derived","expr":"{.journal_shoulder_x} + {.gas_port_ahead_of_shoulder}","via":"harvest"}}],"note":"The catalog's two other mid-length barrels have 9.17 ± 0.04 (Aero's) and 9.13 ± 0.05 (BCM's) by their own photos: a mid-length gas tube has to reach each. 9.178 until 2026-10-05 (overall_length)."},"gas_port_d":{"label":"The gas port's diameter","kind":"length","measurements":[{"id":"photo","value":0.075,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bca-556-16-mid-barrel 53fbcf1e58d8 (Primary Arms 1343-B556MM41617-P_01: three-quarter view, the breech at the top left, 2200 x 1467)","scaleRef":"the journal's width in that photo, 103 px, as the published .750 (journal_od)","method":"the port's dark spot, 10 px across the barrel (11 by 7 px on a 5x crop, the longer way along the axis, which the view shortens by the cosine of 20.5 degrees)","via":"harvest"}},{"id":"chart","value":0.075,"unit":"in","pm":0.01,"stated":"0.075\"ø Gas Port","source":{"type":"spec","publisher":"unknown","name":"AR-15_M4_Barrel_Dimensions.jpg in the user's TDP folder (Spec_Sheets): a third-party illustration of a 14.5 in mid-length barrel, no drawing number","via":"user"}}],"adopt":{"from":"photo","reason":"This barrel's own photo; the chart's figure is the same."},"note":"Not published. Read off Primary Arms' three-quarter photo, for the hole the model cuts; a mid-length chart on file has the same figure, and the Army's rifle-length barrel .092 (8448548)."},"bore_d":{"label":"The bore's diameter (across the lands)","kind":"length","measurements":[{"id":"tdp","value":0.2195,"unit":"in","pm":0.0005,"stated":".219 DIA +.001","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 2 of 2: Section U-U, rifling detail; user-supplied scan (Distribution Statement F, Colt proprietary notice), PDF page 211","via":"user"}},{"id":"reamer-print","value":0.219,"unit":"in","pm":0.0005,"stated":"Bore Size 0.219","source":{"type":"spec","publisher":"manufacturer","name":"Pacific Tool, chamber print 8008, '5.56 Nato Military' (10/31/05; 5.56x45mm_Chamber_Schematic.jpg in the user's TDP folder)","via":"user"}}],"adopt":{"from":"tdp","reason":"The Army's drawing, at the middle of its limits; the reamer maker's print has its lower one."},"note":"The cartridge's, for the hole the model cuts: Bear Creek states \"Caliber 5.56 NATO\" and no bore."},"index_pin_d":{"label":"The barrel indexing pin's diameter","kind":"length","measurements":[{"id":"tdp","value":0.12525,"unit":"in","pm":0.00025,"stated":".1255 DIA -.0005","source":{"type":"standard","doc":"US Army TDP drawing 8448551 (Pin, Barrel Indexing), sheet 1 of 1; user-supplied scan (Distribution Statement F, Colt proprietary notice), PDF page 119","via":"user"}}],"note":"The pin in the top of the extension, which the receiver's notch takes: the Army's own part. The same drawing has it .185 -.005 long."},"index_pin_protrusion":{"label":"The barrel indexing pin's top above the extension's surface","kind":"length","measurements":[{"id":"tdp","value":0.094,"unit":"in","pm":0.01,"stated":".094 MAX","source":{"type":"standard","doc":"US Army TDP drawing 8448548 (Barrel and Barrel Extension Assembly), Section A-A at 2/1; user-supplied scan (Distribution Statement F, Colt proprietary notice), PDF page 212","via":"user"}}],"note":"A limit, and the model draws the pin at it. In the side photo the pin stands about 30 degrees round from the upper edge and shows 4 px (0.035 in) of it."},"index_pin_x":{"label":"The barrel indexing pin's axis behind the flange's rear face","kind":"length","measurements":[{"id":"photo","value":0.063,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bca-556-16-mid-barrel eff6b190e339 (Primary Arms 1343-B556MM41617-P_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the trace's scale there, 121.6 px/in","method":"the upper edge stands above the lower one's radius from the flange's rear face (column 1973) to column 1981: the pin's rear half, begun at the face; its axis half its diameter (index_pin_d) behind the face","via":"harvest"}}],"note":"The pin stands against the flange, as the Army's Section A-A draws it and Primary Arms' three-quarter photos show it."},"thread_minor_d":{"label":"The muzzle thread's minor diameter (its roots)","kind":"length","measurements":[{"id":"tdp","value":0.4551,"unit":"in","pm":0.002,"stated":"MINOR DIA .4551 MAX","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2: Section M-M; user-supplied scan (Distribution Statement F, Colt proprietary notice), PDF page 213","via":"user"}}],"note":"The Army barrel's 1/2-28 thread, for the 1/2 x 28 Bear Creek states: the roots of the rings the model draws. Their crests are the photo's (thread_od)."},"thread_pitch":{"label":"The muzzle thread's pitch","kind":"length","measurements":[{"id":"bca","value":0.03571,"unit":"in","pm":0.00005,"stated":"Thread Pitch 1/2 x 28","source":{"type":"spec","publisher":"manufacturer","name":"Bear Creek Arsenal, BC-15 5.56 NATO, 16\" Parkerized M4 Barrel, 1:7 Twist, Mid-Length Gas System (1343-B556MM41617(P)), Specs","url":"https://www.bearcreekarsenal.com/556-16-parkerized-m4-barrel-1-7-twist-mid-length.html","retrieved":"2026-10-05","via":"harvest"}}],"note":"28 threads to the inch."}}},{"subject":"bca-stripped-lower","title":"Bear Creek Arsenal BC-15 Multi Caliber, Lower Receiver, Black Anodized (LR-15)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"bear-creek","value":1,"unit":"lb","pm":5e-7,"stated":"Weight (lbs) 1.000000","source":{"type":"spec","publisher":"manufacturer","name":"Bear Creek Arsenal, BC-15 Multi Caliber, Lower Receiver, Black Anodized (LR-15), Specs / More Information","url":"https://www.bearcreekarsenal.com/guns-parts/ar-15/ar-15-lowers/stripped-lower-receivers/bca-ar-15-lower-receiver-multi-caliber-black-anodized.html","retrieved":"2026-10-05","via":"harvest"},"note":"A store's weight field to six decimals, in whole pounds: probably what the parcel is charged at, not the receiver."},{"id":"ar15discounts","value":11.2,"unit":"oz","pm":0.05,"stated":"Weight 11.2 oz","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, BCA BC-15 AR-15 Forged Stripped Lower Receiver - LR-15 (SKU 34198), Additional information","url":"https://ar15discounts.com/products/bca-bc-15-ar-15-forged-stripped-lower-receiver/","retrieved":"2026-10-05","via":"harvest"},"note":"Also in its description, as the part's: 'At just 11.2 ounces, it contributes to a balanced, maneuverable firearm'. A seller's figure, beside a size that reads as a box's."}],"adopt":{"from":"ar15discounts","reason":"The one figure a page gives as the receiver's own and to a tenth of an ounce. The maker's is a whole pound in a store's weight field. Both are probably above the bare receiver (a mil-spec forging this size is about 8 to 9 oz: the Workhorse's maker says 8.22, and this part's model in 7075 comes to 7.9): the lighter of the two is taken, the conflict kept."},"note":"Two pages state one and they disagree by a third; neither says how it was taken, and no page states a weighing. Bear Creek's is a store field in whole pounds, the kind shipping is worked out from. AR15Discounts' sits beside 'Dimensions 9.1 x 4.3 x 2.3 in', which is larger than the receiver every way (7.76 x 3.9 by its outline, 1.39 across its tower by the drawing), so it may be the boxed weight. Primary Arms states none. For scale only, not a source: the catalog's other stripped forged lower is 8.22 oz by its maker, and this part's model (4.8 cubic inches, its grip mount and ears as a forging has them) at 7075's 0.102 lb per cubic inch comes to 7.9 oz."},"width":{"label":"Receiver maximum width (Z)","kind":"length","measurements":[{"id":"std","value":0.88,"unit":"in","pm":0.008,"source":{"type":"derived","expr":"{std.ar15.lower_body_width}","via":"harvest"},"note":"Bear Creek: 'Forged to Milspec from 7075 Aluminum'; Primary Arms: 'Fully machined to mil-spec dimensions'. The body's width is the Army drawing's (8448608, Section C-C). Both photos are consistent with it, through cameras whose distance the tower ring's rims set: the far wall's top edge stands 8.8 and 9.2 px over the near wall's where 0.88 gives 9.0 and 9.3, and the far rims seen through the hammer's and trigger's holes sit within a pixel of where 0.88 puts them. Both were part of each camera's fit: consistency, not a reading of the width."}],"note":"No page states a width and no photo looks along the receiver. The body's is the drawing's; the well's walls (std.ar15.magwell_outside_width) and the tower's ring (std.ar15.buffer_tower_od) stand wider and are drawn at the drawing's too."},"buffer_axis_above_pin":{"label":"Receiver extension (bore) axis above the takedown pin centre","kind":"length","measurements":[{"id":"std","value":0.8775,"unit":"in","pm":0.0015,"source":{"type":"derived","expr":"{std.ar15.bore_axis_y}","via":"harvest"},"note":"A mil-spec lower: the threaded hole's centre is the drawing's (.629 above the deck). On both photos the drawing's ring (this axis, std.ar15.buffer_tower_od, its faces) lies on the tower's rims within a pixel (0.011 in) through the cameras the holes fix."}]},"magazine_seat_x":{"label":"Magazine seat, X (a seated magazine's frame origin ahead of the takedown pin)","kind":"length","measurements":[{"id":"milspec","value":3.4915,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{bad-workhorse-lower.magazine_seat_x}","via":"user"},"note":"Where a magazine seats in a mil-spec well: from the Army drawing's well and catch slot and the user's own magazine, recorded on the Workhorse. This lower's well is mil-spec by its maker's and sellers' sentences, and its left photo has the catch's slot where the drawing puts it (X 3.05 to 4.54, Y -0.69 to -0.45 on the wall's plane). No photo of a magazine seated in it is on file."}]},"magazine_seat_y":{"label":"Magazine seat, Y (the feed-lip top of a seated magazine)","kind":"length","measurements":[{"id":"milspec","value":1.003,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{bad-workhorse-lower.magazine_seat_y}","via":"user"},"note":"As magazine_seat_x: the standard well's and the catch's, not this receiver's outside."}]},"grip_mating_y":{"label":"Receiver underside behind the step (where a grip's flat top bears), Y","kind":"length","measurements":[{"id":"right","value":-1.045,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bca-stripped-lower 2376eb37b2cc (right side: Primary Arms' photo 269cebb44010 laid square onto the right face by the drawing's holes, the far wall's overhang taken off)","scaleRef":"frame from the reviewed holes takedown, pivot (200.0 px/in, rms 0.000 in over 2 points)","method":"y_min in x [-0.2, -0.05] of the traced outline (tools/trace.py)","via":"harvest"},"note":"The outline's flat just behind the lug's step: the right face's reading of where a grip's flat top bears (the seat itself is the drawing's: grip_seat_y)."}],"note":"The outline's flat behind the step, read on the right face's plane. Not the seat itself since 2026-10-05 (grip_seat_y takes the drawing's): on a forging the underside behind the lug is round across and the seat's flat stands in from the face, so this edge reads high by its depth x 0.16. The left photo's outline has it at -1.04, and the two agree within 0.015 on every lower edge (the trigger opening -1.06 and -1.065, the ears' bottoms -2.285 and -2.29, -2.33 and -2.345): but both are taken from the same height, so what they share isn't checked by it. The ± allows an edge 0.2 in behind the face."},"grip_seat_y":{"label":"Grip seat, Y (the underside a grip's flat top bears on, at the takedown pin's X)","kind":"length","measurements":[{"id":"tdp","value":-1.0695,"unit":"in","pm":0.0115,"source":{"type":"derived","expr":"{std.ar15.deck_y} - {std.ar15.grip_seat_below_deck}","via":"harvest"},"note":"A mil-spec lower: the flat the lug hangs from is the drawing's, 1.318 ±.010 below the deck."},{"id":"mating","value":-1.045,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.grip_mating_y}","via":"harvest"},"note":"The right photo's outline behind the lug. On a forging the seat's flat reaches the body's side only 0.145 ahead of the pin (its rear edge is a U): what the outline has behind the lug is the flat's edge, 0.04 to 0.16 in from the face, which from this camera reads 0.007 to 0.026 high."}],"adopt":{"from":"tdp","reason":"The drawing dimensions it, and the photo agrees within its ±: 0.025 high, of which the flat's edge standing in from the face accounts for 0.007 to 0.026. Everything else read below the pin line on this photo is 0.02 to 0.03 high the same way (the lug's flat, the guard's holes)."},"note":"The drawing's since 2026-10-05, when the standard's grip mount went into the ledger (std.ar15.grip_seat_below_deck): the photo's own reading (grip_mating_y) is 0.025 above it and inside its ±, and with it the trigger's opening (trigger_opening_top_y, -1.06) would lie below the seat. The lug hung from it is the drawing's too (grip_lug_face_from_pin)."},"grip_lug_face_from_pin":{"label":"The grip lug's sloped face (the face the grip screw goes into), from the takedown pin's centre, square to the face","kind":"length","measurements":[{"id":"tdp","value":1.228,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{std.ar15.grip_lug_face_from_pin}","via":"harvest"},"note":"A mil-spec lower: the lug is the drawing's (1.228 ±.010)."},{"id":"right","value":1.225,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bca-stripped-lower 269cebb44010 (right side, Primary Arms' photo; from about 28 in, 3.5 in above the pin line)","scaleRef":"a pinhole camera fitted to the drawing's hole positions on the part (std.ar15.*: takedown, pivot, selector, hammer, trigger: each rim within 0.007 in), the far rims through the hammer's and trigger's holes, the deck's two edges and the tower ring's rims: 89.3 px/in at the takedown pin, its foot 2.90 ahead of the pin and 3.53 above it, 27.7 in from the right face","method":"the traced outline's sloped stretch under the grip's seat ((0.012, -1.355) to (1.027, -1.930) on the face's plane), each end carried along its line of sight to the lug's own side (0.2525 behind the face: std.ar15.lower_body_width and std.ar15.grip_lug_width), then the line's distance from the pin; ± is 1.5 px and the camera's distance","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's; the photo has it 0.003 nearer the pin once the edge is put at the lug's own depth."},"note":"The check that this lower's lug is the drawing's. On the right face's plane the outline's sloped face is 1.173 from the pin: 0.055 nearer than the drawing's. The lug is .375 across (std.ar15.grip_lug_width), so its side stands 0.2525 behind that face, and carried there along the camera's lines of sight the same edge is 1.225 from the pin: the miss is what the lug's depth gives, in size and in sign."},"grip_lug_face_angle":{"label":"The grip lug's sloped face, from the vertical","kind":"angle","measurements":[{"id":"tdp","value":60,"unit":"deg","pm":2,"source":{"type":"derived","expr":"{std.ar15.grip_lug_face_angle}","via":"harvest"},"note":"A mil-spec lower: the lug is the drawing's (60° ±2°)."},{"id":"right","value":60.5,"unit":"deg","pm":1,"source":{"type":"photo","photo":"references/bca-stripped-lower 269cebb44010 (right side, Primary Arms' photo; from about 28 in, 3.5 in above the pin line)","scaleRef":"a pinhole camera fitted to the drawing's hole positions on the part (std.ar15.*: takedown, pivot, selector, hammer, trigger: each rim within 0.007 in), the far rims through the hammer's and trigger's holes, the deck's two edges and the tower ring's rims: 89.3 px/in at the takedown pin, its foot 2.90 ahead of the pin and 3.53 above it, 27.7 in from the right face","method":"the same stretch of the traced outline, carried to the lug's own side: its lean from the vertical over 1.02 in; ± is 1.5 px at each end","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's; the photo's is half a degree from it."}},"grip_lug_rear_x":{"label":"The grip lug's rear face (under the takedown pin), X","kind":"length","measurements":[{"id":"tdp","value":-0.075,"unit":"in","pm":0.025,"source":{"type":"derived","expr":"{std.ar15.receiver_rear_x} + {std.ar15.grip_lug_front_from_rear_face} - {std.ar15.grip_lug_length}","via":"harvest"},"note":"A mil-spec lower: the lug ends 2.300 ahead of the rear face and is 1.25 long."},{"id":"right","value":-0.054,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bca-stripped-lower 269cebb44010 (right side, Primary Arms' photo; from about 28 in, 3.5 in above the pin line)","scaleRef":"a pinhole camera fitted to the drawing's hole positions on the part (std.ar15.*: takedown, pivot, selector, hammer, trigger: each rim within 0.007 in), the far rims through the hammer's and trigger's holes, the deck's two edges and the tower ring's rims: 89.3 px/in at the takedown pin, its foot 2.90 ahead of the pin and 3.53 above it, 27.7 in from the right face","method":"the traced outline's step down from the seat ((-0.030, -1.047) to (-0.025, -1.317) on the face's plane: grip_shelf_top_x), carried along its lines of sight to the lug's own side; ± is 1.5 px, the camera's distance and where its principal point is","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's; the photo has the face 0.02 ahead of it, inside its ±."}},"grip_lug_flat_y":{"label":"The grip lug's bottom flat (where its sloped face ends, behind the trigger guard's ears), Y","kind":"length","measurements":[{"id":"tdp","value":-1.9995,"unit":"in","pm":0.0215,"source":{"type":"derived","expr":"{std.ar15.deck_y} - {std.ar15.grip_seat_below_deck} - {std.ar15.grip_lug_depth}","via":"harvest"},"note":"A mil-spec lower: the flat is .93 below the seat."},{"id":"right","value":-1.98,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bca-stripped-lower 269cebb44010 (right side, Primary Arms' photo; from about 28 in, 3.5 in above the pin line)","scaleRef":"a pinhole camera fitted to the drawing's hole positions on the part (std.ar15.*: takedown, pivot, selector, hammer, trigger: each rim within 0.007 in), the far rims through the hammer's and trigger's holes, the deck's two edges and the tower ring's rims: 89.3 px/in at the takedown pin, its foot 2.90 ahead of the pin and 3.53 above it, 27.7 in from the right face","method":"the traced outline's flat ((1.027, -1.930) to (1.172, -1.930) on the face's plane), carried along its lines of sight to the lug's own side; ± as grip_lug_rear_x's","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's; the photo has the flat 0.02 above it, inside its ±, as it has everything below the pin line."}},"grip_shelf_top_x":{"label":"Grip shelf start (the step behind the grip), X","kind":"length","measurements":[{"id":"right","value":-0.03,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/bca-stripped-lower 2376eb37b2cc (right side: Primary Arms' photo 269cebb44010 laid square onto the right face by the drawing's holes, the far wall's overhang taken off)","scaleRef":"frame from the reviewed holes takedown, pivot (200.0 px/in, rms 0.000 in over 2 points)","method":"x_min in x [-0.2, 0.6] in y [-1.3, -1.1] of the traced outline (tools/trace.py)","via":"harvest"},"note":"The step behind the grip (a near-upright edge between Y -1.05 and -1.32)."}]},"trigger_opening_top_y":{"label":"Receiver underside above the trigger opening, Y","kind":"length","measurements":[{"id":"right","value":-1.06,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/bca-stripped-lower 2376eb37b2cc (right side: Primary Arms' photo 269cebb44010 laid square onto the right face by the drawing's holes, the far wall's overhang taken off)","scaleRef":"frame from the reviewed holes takedown, pivot (200.0 px/in, rms 0.000 in over 2 points)","method":"y_min in x [1.95, 2.85] of the traced outline (tools/trace.py)","via":"harvest"},"note":"The body's lower edge above the trigger guard's opening."}]},"trigger_guard_front_x":{"label":"Trigger guard front ear hole, X","kind":"length","measurements":[{"id":"tdp","value":3.3425,"unit":"in","pm":0.007,"source":{"type":"derived","expr":"{std.ar15.trigger_guard_front_x}","via":"harvest"},"note":"A mil-spec lower: the hole is the drawing's."},{"id":"right","value":3.323,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bca-stripped-lower 269cebb44010 (right side, Primary Arms' photo; from about 28 in, 3.5 in above the pin line)","scaleRef":"a pinhole camera fitted to the drawing's hole positions on the part (std.ar15.*: takedown, pivot, selector, hammer, trigger: each rim within 0.007 in), the far rims through the hammer's and trigger's holes, the deck's two edges and the tower ring's rims: 89.3 px/in at the takedown pin","method":"the dark of the hole in its spotface, as a blurred disc (px 657.6, 702.3), carried along its line of sight to the spotface's floor (std.ar15.trigger_guard_front_spotface_floor); ± is 2 px and the hole's own depth, which shifts what shows toward the camera's foot","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's; the photo reads 0.02 behind it, inside its ±."}},"trigger_guard_front_y":{"label":"Trigger guard front ear hole, Y","kind":"length","measurements":[{"id":"tdp","value":-2.18,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{std.ar15.trigger_guard_rear_y}","via":"harvest"},"note":"The drawing's side elevation has the guard's two holes on one centre line, 2.18 below the takedown pin (references/tdp crop-guard-holes.png: sheet 1 of 8448608)."},{"id":"right","value":-2.147,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bca-stripped-lower 269cebb44010 (right side, Primary Arms' photo; from about 28 in, 3.5 in above the pin line)","scaleRef":"a pinhole camera fitted to the drawing's hole positions on the part (std.ar15.*: takedown, pivot, selector, hammer, trigger: each rim within 0.007 in), the far rims through the hammer's and trigger's holes, the deck's two edges and the tower ring's rims: 89.3 px/in at the takedown pin","method":"the dark of the hole in its spotface, as a blurred disc (px 657.6, 702.3), carried along its line of sight to the spotface's floor (std.ar15.trigger_guard_front_spotface_floor); ± is 2 px and the hole's own depth: what shows of a hole 0.1 in deep from 12 degrees off its axis is its far end, 0.02 toward the camera's foot (up)","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's. The photo reads 0.03 high, the way a hole's dark reads from above; the rear hole does the same (trigger_guard_rear_y)."}},"trigger_guard_rear_x":{"label":"Trigger guard rear ear hole, X","kind":"length","measurements":[{"id":"tdp","value":1.4985,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{std.ar15.trigger_guard_rear_x}","via":"harvest"},"note":"A mil-spec lower: the hole is the drawing's."},{"id":"right","value":1.505,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bca-stripped-lower 269cebb44010 (right side, Primary Arms' photo; from about 28 in, 3.5 in above the pin line)","scaleRef":"a pinhole camera fitted to the drawing's hole positions on the part (std.ar15.*: takedown, pivot, selector, hammer, trigger: each rim within 0.007 in), the far rims through the hammer's and trigger's holes, the deck's two edges and the tower ring's rims: 89.3 px/in at the takedown pin, its foot 2.90 ahead of the pin and 3.53 above it, 27.7 in from the right face","method":"the hole's rim, a circle of the drawing's diameter fitted to its edge (px 497.2, 705.9), carried along its line of sight to the ears' own face (std.ar15.trigger_guard_ears_width / 2 from the centre: the reference CAD model's 0.659 across)","via":"harvest"}},{"id":"left","value":1.486,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bca-stripped-lower d946dfaa16bc (left side, Bear Creek's own photo; from about 26 in, 3.3 in above the pin line)","scaleRef":"a pinhole camera fitted the same way to the left face's holes (each rim within 0.014 in; the pivot's rim is unclear): 93.6 px/in at the takedown pin, its foot 2.86 ahead of the pin and 3.29 above it, 26.1 in from the left face","method":"the hole's rim, a circle of the drawing's diameter fitted to its edge (px 720.0, 642.0), carried along its line of sight to the ears' own face (std.ar15.trigger_guard_ears_width / 2 from the centre)","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's; the two photos read 0.007 ahead of it and 0.012 behind."}},"trigger_guard_rear_y":{"label":"Trigger guard rear ear hole, Y","kind":"length","measurements":[{"id":"tdp","value":-2.18,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{std.ar15.trigger_guard_rear_y}","via":"harvest"},"note":"A mil-spec lower: the hole is the drawing's."},{"id":"right","value":-2.159,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bca-stripped-lower 269cebb44010 (right side, Primary Arms' photo; from about 28 in, 3.5 in above the pin line)","scaleRef":"a pinhole camera fitted to the drawing's hole positions on the part (std.ar15.*: takedown, pivot, selector, hammer, trigger: each rim within 0.007 in), the far rims through the hammer's and trigger's holes, the deck's two edges and the tower ring's rims: 89.3 px/in at the takedown pin, its foot 2.90 ahead of the pin and 3.53 above it, 27.7 in from the right face","method":"the hole's rim, a circle of the drawing's diameter fitted to its edge (px 497.2, 705.9), carried along its line of sight to the ears' own face (std.ar15.trigger_guard_ears_width / 2 from the centre); ± is 1.5 px, the ears' width and where the camera's principal point is","via":"harvest"}},{"id":"left","value":-2.151,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bca-stripped-lower d946dfaa16bc (left side, Bear Creek's own photo; from about 26 in, 3.3 in above the pin line)","scaleRef":"a pinhole camera fitted the same way to the left face's holes (each rim within 0.014 in; the pivot's rim is unclear): 93.6 px/in at the takedown pin, its foot 2.86 ahead of the pin and 3.29 above it, 26.1 in from the left face","method":"the hole's rim, a circle of the drawing's diameter fitted to its edge (px 720.0, 642.0), carried along its line of sight to the ears' own face (std.ar15.trigger_guard_ears_width / 2 from the centre); ± as the right one's","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's (2.18 below the takedown pin); both photos read it 0.02 to 0.03 high, inside their ±, on the ears' own face."},"note":"Read on the body's face plane both photos had this hole 0.04 to 0.05 above the drawing's (-2.136 and -2.128). The ears stand in from that face: 0.659 across by the reference CAD model (std.ar15.trigger_guard_ears_width, in the ledger since 2026-10-05), 0.11 behind it, and from these cameras a hole there reads 0.022 high. On the ears' own face the two read 0.02 and 0.03 above the drawing's, inside their ±: what is left is the same 0.02 to 0.03 everything below the pin line reads high by on these photos (grip_lug_flat_y, grip_seat_y), where the fire-control holes, at the pin line's height, read within 0.007."},"trigger_pin_x":{"label":"Trigger pin hole centre, X","kind":"length","measurements":[{"id":"tdp","value":1.928,"unit":"in","pm":0.004,"source":{"type":"derived","expr":"{std.ar15.trigger_pin_x}","via":"harvest"},"note":"A mil-spec lower: the hole is the drawing's. Primary Arms: 'Trigger Pin Diameter MIL-SPEC .154'."},{"id":"right","value":1.928,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/bca-stripped-lower 269cebb44010 (right side, Primary Arms' photo; from about 28 in, 3.5 in above the pin line)","scaleRef":"a pinhole camera fitted to the five holes together (takedown, pivot, selector, hammer, trigger at the drawing's positions: 10 coordinates, 7 parameters) with the far rims, the deck's two edges and the tower ring's rims: 89.3 px/in at the takedown pin","method":"the hole's rim, a circle of the drawing's diameter fitted to its edge (px 531.9, 578.5), back on the face's plane: what the fit leaves over, not an independent reading; ± is 1 px","via":"harvest"}},{"id":"left","value":1.924,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/bca-stripped-lower d946dfaa16bc (left side, Bear Creek's own photo; from about 26 in, 3.3 in above the pin line)","scaleRef":"a pinhole camera fitted the same way to the left face's holes: 93.6 px/in at the takedown pin","method":"the hole's rim, a circle of the drawing's diameter fitted to its edge (px 682.3, 510.2), back on the face's plane: what the fit leaves over; ± is 1 px","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's; both photos have the rim on it within a pixel."}},"trigger_pin_y":{"label":"Trigger pin hole centre, Y","kind":"length","measurements":[{"id":"tdp","value":-0.689,"unit":"in","pm":0.0035,"source":{"type":"derived","expr":"{std.ar15.trigger_pin_y}","via":"harvest"},"note":"A mil-spec lower: the hole is the drawing's."},{"id":"right","value":-0.686,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/bca-stripped-lower 269cebb44010 (right side, Primary Arms' photo; from about 28 in, 3.5 in above the pin line)","scaleRef":"a pinhole camera fitted to the five holes together (takedown, pivot, selector, hammer, trigger at the drawing's positions: 10 coordinates, 7 parameters) with the far rims, the deck's two edges and the tower ring's rims: 89.3 px/in at the takedown pin","method":"the hole's rim, a circle of the drawing's diameter fitted to its edge (px 531.9, 578.5), back on the face's plane: what the fit leaves over; ± is 1 px","via":"harvest"}},{"id":"left","value":-0.694,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/bca-stripped-lower d946dfaa16bc (left side, Bear Creek's own photo; from about 26 in, 3.3 in above the pin line)","scaleRef":"a pinhole camera fitted the same way to the left face's holes: 93.6 px/in at the takedown pin","method":"the hole's rim, a circle of the drawing's diameter fitted to its edge (px 682.3, 510.2), back on the face's plane: what the fit leaves over; ± is 1 px","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's; both photos have the rim on it within a pixel."}},"hammer_pin_x":{"label":"Hammer pin hole centre, X","kind":"length","measurements":[{"id":"tdp","value":2.771,"unit":"in","pm":0.004,"source":{"type":"derived","expr":"{std.ar15.hammer_pin_x}","via":"harvest"},"note":"A mil-spec lower: the hole is the drawing's."},{"id":"right","value":2.766,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/bca-stripped-lower 269cebb44010 (right side, Primary Arms' photo; from about 28 in, 3.5 in above the pin line)","scaleRef":"a pinhole camera fitted to the five holes together (takedown, pivot, selector, hammer, trigger at the drawing's positions: 10 coordinates, 7 parameters) with the far rims, the deck's two edges and the tower ring's rims: 89.3 px/in at the takedown pin","method":"the hole's rim, a circle of the drawing's diameter fitted to its edge (px 606.3, 549.8), back on the face's plane: what the fit leaves over; ± is 1 px","via":"harvest"}},{"id":"left","value":2.765,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/bca-stripped-lower d946dfaa16bc (left side, Bear Creek's own photo; from about 26 in, 3.3 in above the pin line)","scaleRef":"a pinhole camera fitted the same way to the left face's holes: 93.6 px/in at the takedown pin","method":"the hole's rim, a circle of the drawing's diameter fitted to its edge (px 604.2, 481.0), back on the face's plane: what the fit leaves over; ± is 1 px","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's; both photos have the rim within 0.006 of it."}},"hammer_pin_y":{"label":"Hammer pin hole centre, Y","kind":"length","measurements":[{"id":"tdp","value":-0.375,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{std.ar15.hammer_pin_y}","via":"harvest"},"note":"A mil-spec lower: the hole is the drawing's."},{"id":"right","value":-0.372,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/bca-stripped-lower 269cebb44010 (right side, Primary Arms' photo; from about 28 in, 3.5 in above the pin line)","scaleRef":"a pinhole camera fitted to the five holes together (takedown, pivot, selector, hammer, trigger at the drawing's positions: 10 coordinates, 7 parameters) with the far rims, the deck's two edges and the tower ring's rims: 89.3 px/in at the takedown pin","method":"the hole's rim, a circle of the drawing's diameter fitted to its edge (px 606.3, 549.8), back on the face's plane: what the fit leaves over; ± is 1 px","via":"harvest"}},{"id":"left","value":-0.388,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/bca-stripped-lower d946dfaa16bc (left side, Bear Creek's own photo; from about 26 in, 3.3 in above the pin line)","scaleRef":"a pinhole camera fitted the same way to the left face's holes: 93.6 px/in at the takedown pin","method":"the hole's rim, a circle of the drawing's diameter fitted to its edge (px 604.2, 481.0), back on the face's plane: what the fit leaves over; ± is 1 px","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's; the right photo has the rim on it, the left 0.013 low (its frame leans 0.5 degrees)."}},"selector_x":{"label":"Safety selector hole centre, X","kind":"length","measurements":[{"id":"tdp","value":0.803,"unit":"in","pm":0.004,"source":{"type":"derived","expr":"{std.ar15.selector_x}","via":"harvest"},"note":"A mil-spec lower: the hole is the drawing's."},{"id":"right","value":0.807,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/bca-stripped-lower 269cebb44010 (right side, Primary Arms' photo; from about 28 in, 3.5 in above the pin line)","scaleRef":"a pinhole camera fitted to the five holes together (takedown, pivot, selector, hammer, trigger at the drawing's positions: 10 coordinates, 7 parameters) with the far rims, the deck's two edges and the tower ring's rims: 89.3 px/in at the takedown pin","method":"the hole's rim on the camera's side (where the face meets the see-through cleanly), a circle of the drawing's diameter fitted to it (px 431.6, 560.3), back on the face's plane: what the fit leaves over; ± is 1 px","via":"harvest"}},{"id":"left","value":0.806,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/bca-stripped-lower d946dfaa16bc (left side, Bear Creek's own photo; from about 26 in, 3.3 in above the pin line)","scaleRef":"a pinhole camera fitted the same way to the left face's holes: 93.6 px/in at the takedown pin","method":"the hole's rim on the camera's side, a circle of the drawing's diameter fitted to it (px 787.1, 490.3), back on the face's plane: what the fit leaves over; ± is 1 px","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's; both photos have the rim within 0.004 of it."}},"selector_y":{"label":"Safety selector hole centre, Y","kind":"length","measurements":[{"id":"std","value":-0.466,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{std.ar15.selector_y}","via":"harvest"},"note":"The standard's (read on the Workhorse's two photos: the drawing's chain for it isn't tied to the pin line on the scan)."},{"id":"right","value":-0.464,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/bca-stripped-lower 269cebb44010 (right side, Primary Arms' photo; from about 28 in, 3.5 in above the pin line)","scaleRef":"a pinhole camera fitted to the five holes together (takedown, pivot, selector, hammer, trigger at the drawing's positions: 10 coordinates, 7 parameters) with the far rims, the deck's two edges and the tower ring's rims: 89.3 px/in at the takedown pin","method":"the hole's rim on the camera's side, a circle of the drawing's diameter fitted to it (px 431.6, 560.3), back on the face's plane: what the fit leaves over; ± is 1 px","via":"harvest"}},{"id":"left","value":-0.463,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/bca-stripped-lower d946dfaa16bc (left side, Bear Creek's own photo; from about 26 in, 3.3 in above the pin line)","scaleRef":"a pinhole camera fitted the same way to the left face's holes: 93.6 px/in at the takedown pin","method":"the hole's rim on the camera's side, a circle of the drawing's diameter fitted to it (px 787.1, 490.3), back on the face's plane: what the fit leaves over; ± is 1 px","via":"harvest"}}],"adopt":{"from":"std","reason":"The standard's; both photos have the rim within 0.003 of it."}},"rear_behind_pin":{"label":"Rear face (the buffer tower's, where the end plate bears) behind the takedown pin","kind":"length","measurements":[{"id":"std","value":1.125,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"-{std.ar15.receiver_rear_x}","via":"harvest"},"note":"A mil-spec lower: the rear face is the drawing's (7.503 -.006 behind the pivot pin). The traced outline has it at 1.120 below the ring in the right photo and 1.125 in the left (rear_face_x)."}]},"rear_face_x":{"label":"Receiver rear face below the tower ring, X","kind":"length","measurements":[{"id":"right","value":-1.12,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/bca-stripped-lower 2376eb37b2cc (right side: Primary Arms' photo 269cebb44010 laid square onto the right face by the drawing's holes, the far wall's overhang taken off)","scaleRef":"frame from the reviewed holes takedown, pivot (200.0 px/in, rms 0.000 in over 2 points)","method":"x_min in y [-0.9, 0.0] of the traced outline (tools/trace.py)","via":"harvest"},"note":"Rear face of the receiver below the tower's ring: the drawing's is -1.125 (std.ar15.receiver_rear_x)."}]},"tower_top_above_pin":{"label":"Top of the buffer-tower ring above the pin line","kind":"length","measurements":[{"id":"std","value":1.5735,"unit":"in","pm":0.0065,"source":{"type":"derived","expr":"{std.ar15.buffer_tower_top_y}","via":"harvest"},"note":"A mil-spec lower: the ring's top is the drawing's (1.325 above the deck)."},{"id":"right","value":1.6,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bca-stripped-lower 269cebb44010 (right side, Primary Arms' photo; from about 28 in, 3.5 in above the pin line)","scaleRef":"a pinhole camera fitted to the drawing's hole positions on the part (std.ar15.*: takedown, pivot, selector, hammer, trigger: each rim within 0.007 in), the far rims through the hammer's and trigger's holes, the deck's two edges and the tower ring's rims: 89.3 px/in at the takedown pin","method":"the silhouette's top over the ring (row 375.5 at columns 282 to 296) against the drawing's ring drawn through the same camera (its top at row 377.9): 2.4 px, 0.027 in, higher. ± covers where the picture's principal point is: taken 400 px lower, the two meet","via":"harvest"}}],"adopt":{"from":"std","reason":"The drawing's. The right photo reads 0.027 higher through a camera whose axis is taken to pass through the picture's centre; a camera aimed lower closes it, and nothing in the photo says which."}},"tower_front_x":{"label":"Buffer-tower front edge (the side walls' sweep up to the ring), X","kind":"length","measurements":[{"id":"right","value":-0.378,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/bca-stripped-lower 2376eb37b2cc (right side: Primary Arms' photo 269cebb44010 laid square onto the right face by the drawing's holes, the far wall's overhang taken off)","scaleRef":"frame from the reviewed holes takedown, pivot (200.0 px/in, rms 0.000 in over 2 points)","method":"x_max in x [-1.5, 3.0] in y [0.5, 1.4] of the traced outline (tools/trace.py)","via":"harvest"},"note":"Front edge of the walls' sweep up to the ring, above the deck."}],"note":"The outline's front edge above the deck between Y 0.5 and 1.4: the walls that sweep up to the ring. The ring's own front face is the drawing's (std.ar15.buffer_tower_front_x), and since 2026-10-12 the walls rise to it along the drawing's arc (std.ar15.rear_wall_arc_r): this figure is how far forward they are drawn at the ring's width under it."},"deck_above_pin":{"label":"Receiver top deck above the pin line","kind":"length","measurements":[{"id":"right","value":0.26,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bca-stripped-lower 2376eb37b2cc (right side: Primary Arms' photo 269cebb44010 laid square onto the right face by the drawing's holes, the far wall's overhang taken off)","scaleRef":"frame from the reviewed holes takedown, pivot (200.0 px/in, rms 0.000 in over 2 points)","method":"top (tooth tops: the edge's max over 0.05 in windows) along x [0.6, 5.8] of the traced outline (tools/trace.py)","via":"harvest"},"note":"The near wall's top edge between the tower and the pivot lug, the far wall's overhang taken off: the drawing's deck is 0.2485 (std.ar15.deck_y)."}],"note":"std.ar15.deck_y is 0.2485 (.250 -.003): the outline's top between the tower and the pivot lug is the near wall's edge once the far wall's overhang is taken off."},"front_ahead_of_pin":{"label":"Front of the pivot-pin lug ahead of the takedown pin","kind":"length","measurements":[{"id":"right","value":6.59,"unit":"in","pm":0.011,"source":{"type":"photo","photo":"references/bca-stripped-lower 2376eb37b2cc (right side: Primary Arms' photo 269cebb44010 laid square onto the right face by the drawing's holes, the far wall's overhang taken off)","scaleRef":"frame from the reviewed holes takedown, pivot (200.0 px/in, rms 0.000 in over 2 points)","method":"x_max of the traced outline (tools/trace.py)","via":"harvest"},"note":"Front of the pivot-pin lug."}]},"bottom_below_pin":{"label":"Lowest point below the pin line (the trigger guard's front ear)","kind":"length","measurements":[{"id":"right","value":2.33,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bca-stripped-lower 2376eb37b2cc (right side: Primary Arms' photo 269cebb44010 laid square onto the right face by the drawing's holes, the far wall's overhang taken off)","scaleRef":"frame from the reviewed holes takedown, pivot (200.0 px/in, rms 0.000 in over 2 points)","method":"−y_min of the traced outline (tools/trace.py)","via":"harvest"},"note":"Lowest point: the trigger guard's front ear, at the well's rear."}],"note":"Read on the body's face plane; the front ear is the well's wall, 0.11 nearer the lens, so it reads about 0.02 low. The rear ear's bottom reads 2.285 the same way, and stands further in than the face (so reads high)."},"magwell_front_x":{"label":"Magwell front face, X","kind":"length","measurements":[{"id":"right","value":6.1,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bca-stripped-lower 2376eb37b2cc (right side: Primary Arms' photo 269cebb44010 laid square onto the right face by the drawing's holes, the far wall's overhang taken off)","scaleRef":"frame from the reviewed holes takedown, pivot (200.0 px/in, rms 0.000 in over 2 points)","method":"x_max in x [3.0, 7.0] in y [-1.5, -0.6] of the traced outline (tools/trace.py)","via":"harvest"},"note":"Front face of the magazine well."}]},"fence_rear_x":{"label":"The magazine catch's fence, its flat face's rear edge, X","kind":"length","measurements":[{"id":"right","value":2.97,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bca-stripped-lower 269cebb44010 (right side, Primary Arms' photo), laid square onto the well walls' plane (std.ar15.magwell_outside_width / 2) through the camera the drawing's holes fix","scaleRef":"that camera: each of the five holes' rims within 0.007 in of the drawing; the picture at 200 px/in in the rifle frame","method":"the edge read on a 3x crop with a 0.1 in grid (.cache/batch123/bca-stripped-lower/grid-right-fence.png): the step up from the body at 2.95, the flat face from 2.97; ± is the slope's width","via":"harvest"}}],"note":"The raised panel the button's pocket opens through, on the right. The reference model's mil-spec fence face runs X 3.023 to 3.566, Y -0.922 to -0.188 (bad-workhorse-lower.fence_rear_x's note): this one is the same face within 0.05."},"fence_front_x":{"label":"The magazine catch's fence, its flat face's front edge, X","kind":"length","measurements":[{"id":"right","value":3.55,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bca-stripped-lower 269cebb44010 (right side, Primary Arms' photo), laid square onto the well walls' plane (std.ar15.magwell_outside_width / 2) through the camera the drawing's holes fix","scaleRef":"that camera: each of the five holes' rims within 0.007 in of the drawing; the picture at 200 px/in in the rifle frame","method":"the edge read on a 3x crop with a 0.1 in grid: the face to 3.55, then a groove (3.57 to 3.60) before the rib beside it","via":"harvest"}}]},"fence_top_y":{"label":"The magazine catch's fence, its flat face's top edge, Y","kind":"length","measurements":[{"id":"right","value":-0.19,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bca-stripped-lower 269cebb44010 (right side, Primary Arms' photo), laid square onto the well walls' plane (std.ar15.magwell_outside_width / 2) through the camera the drawing's holes fix","scaleRef":"that camera: each of the five holes' rims within 0.007 in of the drawing; the picture at 200 px/in in the rifle frame","method":"the edge read on a 3x crop with a 0.1 in grid: the top rib's slope above it ends at -0.19","via":"harvest"}}]},"fence_bottom_y":{"label":"The magazine catch's fence, its flat face's bottom edge, Y","kind":"length","measurements":[{"id":"right","value":-0.93,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bca-stripped-lower 269cebb44010 (right side, Primary Arms' photo), laid square onto the well walls' plane (std.ar15.magwell_outside_width / 2) through the camera the drawing's holes fix","scaleRef":"that camera: each of the five holes' rims within 0.007 in of the drawing; the picture at 200 px/in in the rifle frame","method":"the edge read on a 3x crop with a 0.1 in grid: the face to -0.93, its step down to the body at -0.95","via":"harvest"}}]},"fence_corner_r":{"label":"The magazine catch's fence, its flat face's corners, radius","kind":"length","measurements":[{"id":"right","value":0.07,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bca-stripped-lower 269cebb44010 (right side, Primary Arms' photo), laid square onto the well walls' plane (std.ar15.magwell_outside_width / 2) through the camera the drawing's holes fix","scaleRef":"that camera: each of the five holes' rims within 0.007 in of the drawing; the picture at 200 px/in in the rifle frame","method":"the lower corners' arcs on a 3x crop with a 0.1 in grid, about 40 of its 600 px/in","via":"harvest"}}]},"magwell_wall_rear_x":{"label":"Magazine well's outside walls, rear edge, X (right side)","kind":"length","measurements":[{"id":"right","value":3.58,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bca-stripped-lower 269cebb44010 (right side, Primary Arms' photo), laid square onto the well walls' plane (std.ar15.magwell_outside_width / 2) through the camera the drawing's holes fix","scaleRef":"that camera: each of the five holes' rims within 0.007 in of the drawing; the picture at 200 px/in in the rifle frame","method":"the groove's darkest column read on a 3x crop with a 0.1 in grid, between Y -0.3 and -0.8; ± is the groove's width","via":"harvest"}}],"note":"On the right the walls begin at the groove between the fence and the upright rib that frames the well's flat panel (the rib from 3.60 to 3.87, the panel's edge at 3.93)."},"magwell_wall_rear_x_left":{"label":"Magazine well's outside walls, rear edge, X (left side)","kind":"length","measurements":[{"id":"left","value":3.48,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bca-stripped-lower d946dfaa16bc (left side, Bear Creek's own photo), laid square onto the well walls' plane through the camera the drawing's holes fix","scaleRef":"that camera: each hole's rim within 0.014 in of the drawing (the pivot's unclear: the frame leans 0.5 degrees, 0.02 in at this distance from the takedown pin); the picture at 200 px/in in the rifle frame","method":"the step's shadow read on a 2.4x crop with a 0.1 in grid (.cache/batch123/bca-stripped-lower/grid-left-catch.png), at Y -1.2","via":"harvest"}}],"note":"On the left the wall's rear edge is the step ahead of the trigger guard's front ear; above Y -1.2 it curves back toward the bolt catch's bosses (magwell_wall_upper_rear_x_left)."},"magwell_wall_upper_rear_x_left":{"label":"Magazine well's outside walls, rear edge above the step's curve, X (left side)","kind":"length","measurements":[{"id":"left","value":2.96,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bca-stripped-lower d946dfaa16bc (left side, Bear Creek's own photo), laid square onto the well walls' plane through the camera the drawing's holes fix","scaleRef":"that camera: each hole's rim within 0.014 in of the drawing (the pivot's unclear: the frame leans 0.5 degrees); the picture at 200 px/in in the rifle frame","method":"the step's shadow read on a 2.4x crop with a 0.1 in grid: a straight line from the deck down to Y -0.69","via":"harvest"}}]},"magwell_wall_curve_top_y_left":{"label":"Magazine well's outside walls, left side, where the rear edge starts to curve forward, Y","kind":"length","measurements":[{"id":"left","value":-0.69,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bca-stripped-lower d946dfaa16bc (left side, Bear Creek's own photo), laid square onto the well walls' plane through the camera the drawing's holes fix","scaleRef":"that camera: each hole's rim within 0.014 in of the drawing (the pivot's unclear: the frame leans 0.5 degrees); the picture at 200 px/in in the rifle frame","method":"the step's shadow read on a 2.4x crop with a 0.1 in grid: straight to -0.69, then X 3.09 at -0.9, 3.25 at -1.0, 3.40 at -1.11","via":"harvest"}}]},"magwell_wall_curve_bottom_y_left":{"label":"Magazine well's outside walls, left side, where the rear edge's curve meets the step, Y","kind":"length","measurements":[{"id":"left","value":-1.2,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bca-stripped-lower d946dfaa16bc (left side, Bear Creek's own photo), laid square onto the well walls' plane through the camera the drawing's holes fix","scaleRef":"that camera: each hole's rim within 0.014 in of the drawing (the pivot's unclear: the frame leans 0.5 degrees); the picture at 200 px/in in the rifle frame","method":"the step's shadow read on a 2.4x crop with a 0.1 in grid: X 3.48 by Y -1.2","via":"harvest"}}],"note":"Between the two ends the edge is drawn as a smooth S (3t^2 - 2t^3), within 0.06 of the shadow at each row read."},"bolt_catch_boss_rear_x":{"label":"Bolt catch bosses: the rear boss's rear edge, X (left side)","kind":"length","measurements":[{"id":"left","value":3.05,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bca-stripped-lower d946dfaa16bc (left side, Bear Creek's own photo), laid square onto the well walls' plane through the camera the drawing's holes fix","scaleRef":"that camera: each hole's rim within 0.014 in of the drawing (the pivot's unclear: the frame leans 0.5 degrees); the picture at 200 px/in in the rifle frame","method":"the pad's edge read on a 2.4x crop with a 0.1 in grid; the bosses' face stands 0.07 nearer the lens than the plane read on (0.01 here)","via":"harvest"}}]},"bolt_catch_gap_rear_x":{"label":"Bolt catch bosses: the gap between them (where the catch sits), rear edge, X","kind":"length","measurements":[{"id":"tdp","value":3.203,"unit":"in","pm":0.007,"source":{"type":"derived","expr":"{std.ar15.bolt_catch_slot_front_x} - {std.ar15.bolt_catch_slot_width}","via":"harvest"},"note":"The gap is the drawing's slot for the catch, at the left face."},{"id":"left","value":3.205,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bca-stripped-lower d946dfaa16bc (left side, Bear Creek's own photo), laid square onto the well walls' plane through the camera the drawing's holes fix","scaleRef":"that camera: each hole's rim within 0.014 in of the drawing (the pivot's unclear: the frame leans 0.5 degrees); the picture at 200 px/in in the rifle frame","method":"the slot's dark edge read on a 2.4x crop with a 0.1 in grid","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's slot; the photo's edge is on it."}},"bolt_catch_gap_front_x":{"label":"Bolt catch bosses: the gap's front edge, X","kind":"length","measurements":[{"id":"tdp","value":3.375,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.ar15.bolt_catch_slot_front_x}","via":"harvest"},"note":"The gap is the drawing's slot for the catch, at the left face."},{"id":"left","value":3.38,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bca-stripped-lower d946dfaa16bc (left side, Bear Creek's own photo), laid square onto the well walls' plane through the camera the drawing's holes fix","scaleRef":"that camera: each hole's rim within 0.014 in of the drawing (the pivot's unclear: the frame leans 0.5 degrees); the picture at 200 px/in in the rifle frame","method":"the slot's dark edge read on a 2.4x crop with a 0.1 in grid","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's slot; the photo's edge is on it."}},"bolt_catch_boss_front_x":{"label":"Bolt catch bosses: the front boss's front edge, X","kind":"length","measurements":[{"id":"left","value":3.58,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bca-stripped-lower d946dfaa16bc (left side, Bear Creek's own photo), laid square onto the well walls' plane through the camera the drawing's holes fix","scaleRef":"that camera: each hole's rim within 0.014 in of the drawing (the pivot's unclear: the frame leans 0.5 degrees); the picture at 200 px/in in the rifle frame","method":"the pad's edge read on a 2.4x crop with a 0.1 in grid","via":"harvest"}}]},"bolt_catch_boss_bottom_y":{"label":"Bolt catch bosses: their bottom edges, Y (they rise to the deck)","kind":"length","measurements":[{"id":"left","value":-0.14,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bca-stripped-lower d946dfaa16bc (left side, Bear Creek's own photo), laid square onto the well walls' plane through the camera the drawing's holes fix","scaleRef":"that camera: each hole's rim within 0.014 in of the drawing (the pivot's unclear: the frame leans 0.5 degrees); the picture at 200 px/in in the rifle frame","method":"the pads' lower edges read on a 2.4x crop with a 0.1 in grid; the bosses' face stands 0.07 nearer the lens than the plane read on, so this reads 0.01 low","via":"harvest"}}]},"well_roll_crest_out":{"label":"The roll along the top of the magazine well's right wall, its crest from the centre plane (Z)","kind":"length","measurements":[{"id":"workhorse","value":0.8,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{bad-workhorse-lower.well_roll_crest_out}","via":"harvest"},"note":"The same roll on the catalog's other forged mil-spec lower, read there through a camera fitted to an oblique photo and checked by its published width. On this lower's own photo the roll's lower edge (-0.204), its rear end's foot (2.91) and its flat front end (6.237) are the Workhorse's -0.204, 2.905 and 6.231: one forging pattern."},{"id":"right","value":0.85,"unit":"in","pm":0.07,"source":{"type":"photo","photo":"references/bca-stripped-lower 2376eb37b2cc (right side: Primary Arms' photo 269cebb44010 laid square onto the right face by the drawing's holes)","scaleRef":"frame from the reviewed holes takedown (320, 400), pivot (1595, 400): 200.0 px/in on the body's right face; what stands off that face shows moved away from the camera's foot (X 2.899, Y 3.534, 27.69 in from the face: the rectification's own camera) and is put back","method":"the small blind hole in the roll shows at X 5.336, Y -0.029 on the face's plane; a point as far off the face as the Workhorse's roll (0.80 from the centre) that shows there is at Y +0.018, one 0.86 from the centre at +0.026: the Workhorse's hole is at +0.024. On the walls' own face (0.549) it would be at -0.015","via":"harvest"},"note":"Rests on this lower's hole being at the Workhorse's height (+0.024 ± 0.006, level with the pivot pin); the ± is that and a pixel on the photo."}],"adopt":{"from":"workhorse","reason":"The Workhorse's is a reading (± 0.04); this lower's own photo can only say that its roll stands about as far off (0.85 ± 0.07), and that it is no flat wall."}},"well_roll_bottom_y":{"label":"The roll along the top of the well's right wall, its lower edge (where its underside meets the wall's face), Y","kind":"length","measurements":[{"id":"right","value":-0.204,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bca-stripped-lower 2376eb37b2cc (right side: Primary Arms' photo 269cebb44010 laid square onto the right face by the drawing's holes)","scaleRef":"frame from the reviewed holes takedown (320, 400), pivot (1595, 400): 200.0 px/in on the body's right face; what stands off that face shows moved away from the camera's foot (X 2.899, Y 3.534, 27.69 in from the face: the rectification's own camera) and is put back","method":"brightness down five columns from X 4.15 to 6.0 (7 px bands): the roll's underside is darkest at 436 to 440 px and half-way back to the face's brightness at 443.2 to 444.4 px, which on the walls' face (0.109 in off the body's) is -0.202 to -0.207","via":"harvest"},"note":"The Workhorse's is -0.204. The ± is the run of the shading."}]},"well_roll_rear_x":{"label":"The roll along the top of the well's right wall, its rear end (the foot of its rounded end, on the body), X","kind":"length","measurements":[{"id":"right","value":2.91,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bca-stripped-lower 2376eb37b2cc (right side: Primary Arms' photo 269cebb44010 laid square onto the right face by the drawing's holes)","scaleRef":"frame from the reviewed holes takedown (320, 400), pivot (1595, 400): 200.0 px/in on the body's right face; what stands off that face shows moved away from the camera's foot (X 2.899, Y 3.534, 27.69 in from the face: the rectification's own camera) and is put back","method":"brightness along rows Y +0.075, 0 and -0.075 (5 px bands): the body's grey to 902 to 903 px (2.91), then the end's shadow (darkest at 2.96), the roll's own brightness by 3.12","via":"harvest"},"note":"The Workhorse's is 2.905, its shadow darkest at 2.96 too."}]},"well_roll_rear_round":{"label":"The roll along the top of the well's right wall, how far its rounded rear end runs before the roll is full","kind":"length","measurements":[{"id":"right","value":0.2,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bca-stripped-lower 2376eb37b2cc (right side: Primary Arms' photo 269cebb44010 laid square onto the right face by the drawing's holes)","scaleRef":"frame from the reviewed holes takedown (320, 400), pivot (1595, 400): 200.0 px/in on the body's right face; what stands off that face shows moved away from the camera's foot (X 2.899, Y 3.534, 27.69 in from the face: the rectification's own camera) and is put back","method":"the same three rows: from the end's foot at 2.91 to the roll's own brightness at 3.10 to 3.13 (shown at 3.125 to 3.15, a quarter inch off the face)","via":"harvest"},"note":"The Workhorse's is 0.19."}]},"well_roll_front_x":{"label":"The roll along the top of the well's right wall, its front end (a flat face beside the pivot lug), X","kind":"length","measurements":[{"id":"right","value":6.237,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bca-stripped-lower 2376eb37b2cc (right side: Primary Arms' photo 269cebb44010 laid square onto the right face by the drawing's holes)","scaleRef":"frame from the reviewed holes takedown (320, 400), pivot (1595, 400): 200.0 px/in on the body's right face; what stands off that face shows moved away from the camera's foot (X 2.899, Y 3.534, 27.69 in from the face: the rectification's own camera) and is put back","method":"brightness along rows Y +0.075, 0 and -0.15 (5 px bands): the roll ends at 1566 to 1568 px, the lug's lighter face ahead of it (the edge's foot is on the lug's face, the photo's own plane)","via":"harvest"},"note":"0.138 in behind the pivot pin's axis; the Workhorse's is 6.231. The Army's pivot pin has a flat on its head .1355 from its axis (8448621): this face is what the flat lies against."}]}}},{"subject":"bcm-115-carbine-barrel","title":"BCM Standard 11.5\" Carbine Barrel, Stripped (BCM-BRL-s-11-STD)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"bcm","value":21,"unit":"oz","pm":1,"stated":"Approximate Weight: 1lb 5oz.","source":{"type":"spec","publisher":"manufacturer","name":"BCM, BCM Standard 11.5\" Carbine Barrel, Stripped (BCM-BRL-s-11-STD), Description","url":"https://bravocompanyusa.com/bcm-standard-11-5-carbine-barrel-stripped-nfa/","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":21,"unit":"oz","pm":0.5,"stated":"1 lb 5 oz weight","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Bravo Company Manufacturing Chrome Lined 5.56 AR-15 Barrel - Carbine - Government - 11.5\" (BCM-BRL-S-11-STD), Features and Specifications","url":"https://www.primaryarms.com/bravo-company-bcm-ar-15-barrel-11.5in-5.56-nato-carbine-length-govt-profile","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"bcm","reason":"The maker's own figure, with its own word for how exact it is; the seller's is the same weight."},"note":"\"Approximate\" is BCM's word: the ± is a whole ounce. Primary Arms states the same figure."},"length":{"label":"Barrel length as its maker states it","kind":"length","measurements":[{"id":"bcm","value":11.5,"unit":"in","pm":0.05,"stated":"These are stripped 11.5\" carbine gas Standard 11595E barrels with gas ports installed and dimpled for a strong gas block installation.","source":{"type":"spec","publisher":"manufacturer","name":"BCM, BCM Standard 11.5\" Carbine Barrel, Stripped (BCM-BRL-s-11-STD), Description","url":"https://bravocompanyusa.com/bcm-standard-11-5-carbine-barrel-stripped-nfa/","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":11.5,"unit":"in","pm":0.05,"stated":"Barrel Length 11.5","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Bravo Company Manufacturing Chrome Lined 5.56 AR-15 Barrel - Carbine - Government - 11.5\" (BCM-BRL-S-11-STD), Specifications","url":"https://www.primaryarms.com/bravo-company-bcm-ar-15-barrel-11.5in-5.56-nato-carbine-length-govt-profile","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"bcm","reason":"The maker's own; the seller repeats it."},"note":"The nominal length. BCM's page doesn't say between which points; the Army's barrel drawing (8448549) dimensions a barrel from its breech end, inside the extension, to its muzzle, and overall_length takes it so."},"journal_od":{"label":"The gas block journal's diameter","kind":"length","measurements":[{"id":"bcm","value":0.75,"unit":"in","pm":0.0005,"stated":"(.750) at Gas Block location","source":{"type":"spec","publisher":"manufacturer","name":"BCM, BCM Standard 11.5\" Carbine Barrel, Stripped (BCM-BRL-s-11-STD), Description","url":"https://bravocompanyusa.com/bcm-standard-11-5-carbine-barrel-stripped-nfa/","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":0.75,"unit":"in","pm":0.0005,"stated":"Gas Seat Diameter .750","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Bravo Company Manufacturing Chrome Lined 5.56 AR-15 Barrel - Carbine - Government - 11.5\" (BCM-BRL-S-11-STD), Specifications","url":"https://www.primaryarms.com/bravo-company-bcm-ar-15-barrel-11.5in-5.56-nato-carbine-length-govt-profile","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"bcm","reason":"The maker's own; the seller repeats it."}},"extension_behind_breech":{"label":"The barrel extension's rear end behind the barrel's breech end","kind":"length","measurements":[{"id":"model","value":0.501,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{std.ar15.barrel_extension_behind_breech}","via":"user"}}],"note":"The standard's: the reference CAD set's extension less the Army's .620 tenon (std.ar15.barrel_extension_behind_breech), the one figure the catalog's 5.56 barrels take their breech from. BCM: \"M4 Feed Ramp Barrel Extension\"."},"overall_length":{"label":"End to end, the extension's rear to the muzzle","kind":"length","measurements":[{"id":"photo","value":12.2,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"its extension's body as the Army's .999 (extension_od) and its journal as the published .750 (journal_od)","method":"its two end faces, each behind its rim's arc (columns 104.2 and 2101.8: outline_rear_face, outline_front_face), at the scales its extension's body and its journal give with their edges read at grey 200 and no allowance for the cut-out's edge (164.49 px/in at column 175, 163.44 at 1577, a straight line between and beyond)","via":"harvest"}},{"id":"thread","value":12.05,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"its muzzle thread's pitch as 28 to the inch (thread_pitch), with its extension's body and its journal","method":"the same two faces, with the thread as the ruler: the calibration fixed by the two diameters and by 28 threads to the inch at the muzzle (5.905 px a thread on rows just inside each edge, columns 2008 to 2090; the spectrum's peak, 5.87 to 5.93 by the row) in place of the published length","via":"harvest"}},{"id":"published","value":12.001,"unit":"in","pm":0.07,"source":{"type":"derived","expr":"{.length} + {.extension_behind_breech}","via":"harvest"}}],"adopt":{"from":"published","reason":"The maker's length: the site's line on the law goes by it, and the photo's calibration is fixed by it. The thread's pitch, which doesn't use it, agrees within 0.4%; the two diameters with their edges as read are 1.7% longer, by the cut-out's edge."},"note":"The published length is the scale for lengths: it is one of the three knowns the photo's calibration is fixed by, with the extension's body (the Army's .999) and the journal (.750). The two diameters alone, their edges read at grey 200, have the barrel 1.7% longer (the 14.5 in barrel's photo reads 1.5% longer the same way, the 16 in barrel's 2.5%: a black tube reads thin on white); what closes it is 1.09 px on each edge, a cut-out's width. The checks that are not among the three: the thread's own pitch as the ruler has the barrel 12.05 (the second measurement here: 0.4% from the published one), the plain relief behind the thread comes out at 0.496 (the Army's crests .4957), the indexing pin at 0.127 across (the reference CAD set's .125), the flange at 1.176 (1.170), the extension 0.990 long behind its flange (0.990), the thread 0.62 long from the shoulder (the Army's .63), and the gas port 1.96 and 1.99 behind its two mid-length siblings'. The ± of the published one covers whether the 11.5 is from the barrel's breech end (the Army's drawing) or from the bolt's face, an eighth further back."},"extension_rear_x":{"label":"The barrel extension's rear end, from the flange's rear face (negative: inside the receiver)","kind":"length","measurements":[{"id":"photo","value":-0.99,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.8 px/in along the axis there","method":"the rear end's face (column 104.2: outline_rear_face, behind its rim's arc of 7.5 px) to the flange's rear face (column 269.5): where the flange's lower edge reaches its full depth, up its rim's near arc (7.4 px deep, seen for 4 px; the pin hides the upper edge there)","via":"harvest"}}],"note":"The reference CAD set's extension has 0.990 here (1.121 less its 0.131 flange); the 16 in barrel's own photo 0.984, the 14.5 in barrel's 0.984."},"flange_front_x":{"label":"The extension flange's front face, ahead of its rear face (the flange's thickness)","kind":"length","measurements":[{"id":"photo","value":0.114,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.8 px/in along the axis there","method":"the flange's rear face (column 269.5) to where its edges stop being level (column 288.5)","via":"harvest"}}],"note":"The reference CAD set's flange is 0.131 thick; this one reads thinner, as its two siblings' did by their own photos (0.095 and 0.102)."},"flange_d":{"label":"The barrel extension's flange, its diameter","kind":"length","measurements":[{"id":"photo","value":1.176,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.65 px/in there","method":"the silhouette's widest, columns 272 to 287: 193.8 px, with the cut-out's 2.18 px","via":"harvest"}}],"note":"The reference CAD set's is 1.170. (flange_od is this same height at the journal's scale alone, the outline's scale reference.)"},"extension_od":{"label":"The barrel extension's body, its diameter (what goes into the receiver)","kind":"length","measurements":[{"id":"tdp","value":0.999,"unit":"in","pm":0.001,"stated":"DIAMETER NOT TO EXCEED .9990 FOR THIS LENGTH AFTER ASSEMBLY AND BEFORE FINISH","source":{"type":"standard","doc":"US Army TDP drawing 8448548 (Barrel and Barrel Extension Assembly), rev N: the assembly's side view at 1/1; user-supplied scan, PDF page 212","via":"user"},"note":"An upper limit: it goes into the receiver's 1.000 bore (8448524). The reference CAD set's extension is .9987."},{"id":"photo","value":1.005,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"its gas block journal's diameter as the published .750 (journal_od): 163.44 px/in","method":"the extension's body, columns 115 to 235: 164.33 px against the journal's 122.58 (a line through each edge at grey 200)","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's limit: an extension over 1.000 doesn't go into a receiver. The photo reads 0.5% large here because its breech end is nearer the lens than its journal."},"note":"The photo's reading says how square the photo is, not how big the extension is: at the journal's scale it is 0.5% large, the breech end standing a little nearer the lens than the journal. It is one of the three knowns the photo's calibration is fixed by (with the journal's .750 and the published length), so the model draws it at the drawing's."},"chamber_od":{"label":"The chamber section's diameter (between the flange and the taper)","kind":"length","measurements":[{"id":"photo","value":0.981,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.63 px/in there","method":"columns 310 to 392: 161.33 px (a line through each edge at grey 200), with the cut-out's 2.18 px","via":"harvest"}}],"note":"The 14.5 in barrel's reads .980 by its own photo."},"taper_rear_x":{"label":"Where the taper ahead of the chamber section begins, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":0.77,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.8 px/in along the axis there","method":"the flange's rear face (column 269.5) to where the straight taper's edges, carried back, meet the chamber section's (column 398)","via":"harvest"}}]},"taper_front_x":{"label":"Where the taper ends and the section under the handguard begins, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":1.631,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.7 px/in along the axis there","method":"the flange's rear face (column 269.5) to where the taper's edges meet the section's ahead (column 541.5)","via":"harvest"}}],"note":"A straight cone: its edges are lines from column 405 to 540."},"handguard_rear_od":{"label":"The section under the handguard, its diameter at its rear end (the taper's foot)","kind":"length","measurements":[{"id":"photo","value":0.679,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.59 px/in there","method":"a line through each edge over columns 560 to 900, carried to column 545: 111.0 px, with the cut-out's 2.18 px","via":"harvest"}}],"note":"The section narrows toward the muzzle as far as handguard_knee_x and is level from there to the ramp."},"handguard_knee_x":{"label":"Where the section under the handguard stops narrowing, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":5.22,"unit":"in","pm":0.3,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.4 px/in along the axis there","method":"the flange's rear face (column 269.5) to column 1140, where the lines through the narrowing stretch (columns 560 to 1100) reach the level stretch's width (106.7 px)","via":"harvest"}}],"note":"The edges close by 0.0073 px a column from column 545 and are level within a fifth of a pixel from about column 1140 to the ramp: where one becomes the other is good to a third of an inch."},"handguard_front_od":{"label":"The section under the handguard, its diameter over its level front end (to where the ramp to the collar begins)","kind":"length","measurements":[{"id":"photo","value":0.654,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.43 px/in there","method":"columns 1147 to 1231: 106.7 px, with the cut-out's 2.18 px","via":"harvest"}}]},"ramp_rear_x":{"label":"Where the ramp up to the collar begins, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":5.777,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.4 px/in along the axis there","method":"the flange's rear face (column 269.5) to where the edges leave the section's line (column 1232)","via":"harvest"}}],"note":"A concave ramp, steepening to a sharp corner at the collar's full diameter."},"ramp_mid_x":{"label":"A station midway up the ramp, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":6.017,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.4 px/in along the axis there","method":"the flange's rear face (column 269.5) to column 1272","via":"harvest"}}],"note":"With ramp_mid_od: the third point the model's arc is put through."},"ramp_mid_od":{"label":"The ramp's diameter at that station","kind":"length","measurements":[{"id":"photo","value":0.713,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.41 px/in there","method":"column 1272: 116.52 px, with the cut-out's 2.18 px","via":"harvest"}}]},"collar_rear_x":{"label":"Where the collar reaches its full diameter (the ramp's top), ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":6.254,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.4 px/in along the axis there","method":"the flange's rear face (column 269.5) to where the edges become level (column 1311.5)","via":"harvest"}}]},"collar_od":{"label":"The collar behind the gas block journal, its diameter","kind":"length","measurements":[{"id":"photo","value":0.855,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.39 px/in there","method":"columns 1320 to 1400: 140.05 px (a line through each edge at grey 200), with the cut-out's 2.18 px","via":"harvest"}}],"note":"What a gas block's rear face comes back to. The 14.5 in barrel's reads .854 by its own photo, the 16 in barrel's 0.86."},"collar_chamfer":{"label":"The chamfer on the collar's front corner (along the barrel; as much down the face: 45 degrees)","kind":"length","measurements":[{"id":"photo","value":0.037,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.3 px/in along the axis there","method":"where the collar's edges begin to fall (column 1409) to its front face (column 1415.2): 6.2 px; the edge is 5.5 px lower at the face (64.6 px of radius against 70.1)","via":"harvest"}}],"note":"The edges fall 5.5 px toward the axis over the 6.2 px before the face: as much down as along, within a pixel. Primary Arms' close view of the journal (2583fd18e700) shows it as a lighter band round the collar's rim."},"journal_rear_x":{"label":"The gas block journal's rear shoulder (the collar's front face) ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":6.878,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.3 px/in along the axis there","method":"the flange's rear face (column 269.5) to the collar's front face (column 1415.2): where its edges drop to the groove's, 0.8 px before the drop's end at column 1416 (the face's rim, 65 px in radius under the chamfer, is an arc 1.9 px deep from this far, seen past the groove for 0.8)","via":"harvest"}}],"note":"A gas block's rear face comes back to this shoulder. The collar's corner is cut off behind it (collar_chamfer); the relief groove begins at it."},"groove_front_x":{"label":"The relief groove at the collar's front face, its front wall ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":6.923,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.3 px/in along the axis there","method":"the flange's rear face (column 269.5) to where the edges are back up at the journal's (column 1422.7)","via":"harvest"}}],"note":"A groove 0.045 in wide between the collar's face and the journal, on the silhouette here; Primary Arms' close view of the journal (2583fd18e700) shows it as a dark band with a bright rim."},"groove_od":{"label":"The relief groove's diameter at its floor","kind":"length","measurements":[{"id":"photo","value":0.725,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.38 px/in there","method":"columns 1417 to 1421: 118.5 px (118.0 to 118.9), with the cut-out's 2.18 px","via":"harvest"}}],"note":"0.013 in under the journal's surface on each side. The lens's blur fills a groove 7 px wide a little: it may be deeper."},"gas_port_x":{"label":"The gas port ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":7.138,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.3 px/in along the axis there","method":"the flange's rear face (column 269.5) to the port (column 1458.5: between the middle of its mouth's dip in the upper edge and the middle of the dimple's dent in the lower)","via":"harvest"}}],"note":"BCM says \"gas ports installed and dimpled\" and gives no distance. The port is on top in this photo, in line with the indexing pin: its mouth dips the upper edge by a fifth of a pixel over columns 1448 to 1463, and the dimple opposite it dents the lower edge by 0.65 px over columns 1448 to 1471. The dent is the surer of the two: the port is put three parts toward its middle (column 1459.5) from the dip's (1455.5). That is 0.26 ahead of the journal's rear shoulder (the 14.5 in barrel's own photo has 0.29, the 16 in barrel's 0.28; 8448548 has .295 on the rifle's barrel; BCM's own gas block has its port 0.275 ahead of its rear face), and 1.96 behind the 14.5 in barrel's mid-length port and 1.99 behind the 16 in barrel's: a carbine-length gas tube is 2 in shorter than a mid-length one. A second look: in Primary Arms' close view of the journal (2583fd18e700) the port's middle is 3.85 of its own mouth's lengths ahead of the collar's face along the barrel, 0.27 to 0.30 for a port of .070 to .078."},"dimple_d":{"label":"The dimple under the journal opposite the gas port, its width along the barrel","kind":"length","measurements":[{"id":"photo","value":0.144,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.3 px/in along the axis there","method":"the dent in the lower edge, columns 1448 to 1471: 24 px","via":"harvest"}}],"note":"BCM: \"gas ports installed and dimpled for a strong gas block installation\". Its depth isn't shown: the silhouette's dent (0.65 px) is only the chord its rim cuts across the journal's underside, which a dimple this wide and deeper than 0.007 in would make 1.2 px. Not drawn."},"journal_front_x":{"label":"The gas block journal's front end (where the barrel steps down) ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":8.803,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.2 px/in along the axis there","method":"the flange's rear face (column 269.5) to the journal's front face (column 1735.2): where its edges drop, a pixel before the drop's end; its corner is broken over the 4 px before","via":"harvest"}}],"note":"The journal is 1.93 long, as the 14.5 in barrel's is by its own photo: long enough for a front sight base's two bands."},"mid_od":{"label":"The diameter ahead of the journal (between its front end and the step behind the muzzle)","kind":"length","measurements":[{"id":"photo","value":0.726,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.28 px/in there","method":"columns 1752 to 1885: 118.58 px (a line through each edge at grey 200), with the cut-out's 2.18 px","via":"harvest"}}],"note":"The 14.5 in barrel's reads .718 by its own photo."},"step_x":{"label":"The step behind the muzzle (where the last section begins) ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":9.813,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.1 px/in along the axis there","method":"the flange's rear face (column 269.5) to the step's face (column 1903): where the edges drop, a pixel before the drop's end","via":"harvest"}}]},"muzzle_od":{"label":"The diameter behind the muzzle thread","kind":"length","measurements":[{"id":"photo","value":0.699,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.25 px/in there","method":"columns 1912 to 1985: 114.1 px (a line through each edge at grey 200), with the cut-out's 2.18 px","via":"harvest"}}],"note":"The last section before the shoulder, 0.57 long. The 14.5 in barrel's reads .700 by its own photo."},"shoulder_chamfer":{"label":"The chamfer on the muzzle shoulder's corner (along the barrel; as much down the face: 45 degrees)","kind":"length","measurements":[{"id":"photo","value":0.035,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.0 px/in along the axis there","method":"where the last section's edges begin to fall (column 1992.5) to the shoulder's face (column 1998.3): 5.8 px; the edge is 5.7 px lower at the face (51.4 px of radius against 57.1)","via":"harvest"}}],"note":"The edges fall 5.7 px toward the axis over the 5.8 px before the face. Primary Arms' close view of the muzzle (798114485812) shows it as a lighter band round the shoulder's rim. The 14.5 in barrel's level photo, taken from close by, fits a shoulder with none or little."},"shoulder_x":{"label":"The muzzle shoulder ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":10.387,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.0 px/in along the axis there","method":"the flange's rear face (column 269.5) to the shoulder's face (column 1998.3): 2.7 px before the edges reach the relief's (column 2001), where the arc of its rim (51.4 px in radius under the chamfer) ends","via":"harvest"}}],"note":"Where the thread begins: a muzzle device or its washer seats here. Its corner is cut off (shoulder_chamfer), and past the face the silhouette is the face's rim, an arc 4.3 px deep from this far, seen past the relief for 2.7 px. Ahead of it a plain relief the thread's size, 0.06 long, before the first turn."},"thread_length":{"label":"The muzzle thread's length","kind":"length","measurements":[{"id":"photo","value":0.624,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.0 px/in along the axis there","method":"the shoulder's face (column 1998.3) to the muzzle's face (column 2101.8: outline_front_face, behind its rim's arc and its crown's break)","via":"harvest"}}],"note":"From the shoulder to the muzzle's face, the relief behind the first turn included: the Army's .63 (8448549 sheet 1; a mid-length chart has .624). The 14.5 in barrel's own photo reads 0.61. The thread's own pitch reads 5.905 px here (rows just inside each edge, columns 2008 to 2090), which is 28 to the inch at 165.3 px/in where the calibration has 166.0: the thread as the ruler agrees within 0.4%."},"thread_relief_d":{"label":"The plain relief between the shoulder and the thread's first turn, its diameter","kind":"length","measurements":[{"id":"photo","value":0.496,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.24 px/in there","method":"columns 2002 to 2007: 80.3 px, with the cut-out's 2.18 px","via":"harvest"}}],"note":"The thread's blank, unthreaded for 0.06 in ahead of the shoulder: it reads the Army thread's major diameter (.4957), a check of the calibration at the muzzle. Not drawn as such: the model's thread runs out there."},"index_pin_x":{"label":"The barrel indexing pin's axis behind the flange's rear face","kind":"length","measurements":[{"id":"photo","value":0.081,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.9 px/in along the axis there","method":"the pin on the upper edge (columns 246.5 to 265.5: its middle at 256) to the flange's rear face (column 269.5)","via":"harvest"}}],"note":"The pin is on the upper edge in this photo. The reference CAD set has 0.0765 (0.2075 behind the flange's front face, less its 0.131 flange); the 14.5 in barrel's own photo 0.086, the 16 in barrel's 0.113."},"index_pin_top":{"label":"The barrel indexing pin's top above the bore's axis","kind":"length","measurements":[{"id":"photo","value":0.594,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.65 px/in there","method":"the pin's top on the upper edge, columns 250 to 263: 97.9 px above the axis, with the cut-out's 1.09 px","via":"harvest"}}],"note":"A hair over the flange's rim (0.588): the 16 in barrel's own photo has its pin a hair under its flange's (0.584 against 0.5925)."},"outline_lens_x":{"label":"The photo's calibration: the lens's foot along the traced outline (in the outline's own frame, from the silhouette's rear tip)","kind":"length","measurements":[{"id":"photo","value":6.134,"unit":"in","pm":0.5,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"the traced outline's own (flange_od): 163.6 px/in","method":"column 1100 of 2200, in the outline's unit (163.6 px/in from its tip at column 96.7)","via":"harvest"}}],"note":"The picture's middle, taken as that: from this far (the rear end's rim is an arc 7.5 px deep on a radius of 82: the lens about 65 in off) a step's rim is an arc of 2 to 5 px, and where the lens's foot lies moves nothing by more than a few thousandths."},"outline_yaw_run":{"label":"The photo's calibration: how fast its scale changes toward the muzzle (the scale is 1 + (x - outline_lens_x) / this, x along the traced outline; negative: smaller at the muzzle)","kind":"length","measurements":[{"id":"photo","value":-4310,"unit":"in","pm":1500,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"its extension's body (extension_od) and its journal (journal_od)","method":"the extension's body (164.33 px at column 175) as the Army's .999 and the journal (122.58 px at column 1577) as the published .750, each with the cut-out's 2.18 px: 166.67 and 166.34 px/in, 1402 px apart","via":"harvest"}}],"note":"The barrel leans 0.9 degrees to the lens, its breech nearer: the extension's body reads 0.5% large against the journal. A lean changes a diameter's scale in a straight line along the picture, and a length's twice as fast (a point of the axis at x is (x - outline_lens_x) / scale from the lens's foot). The scale falls 0.28% from the rear face to the muzzle."},"outline_inset":{"label":"The photo's calibration: how far inside the barrel's edge the cut-out's edge at grey 200 stands, on each side (in the outline's unit)","kind":"length","measurements":[{"id":"photo","value":0.0067,"unit":"in","pm":0.003,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"its extension's body (extension_od), its journal (journal_od) and its published length (overall_length)","method":"solved: the length between the end faces (columns 104.2 and 2101.8) at the scales the extension's body and the journal give is 12.001 with 2.18 px added to every width, 12.196 with none","via":"harvest"}}],"note":"1.09 px. What makes the two known diameters' scales give the published length between the end faces (overall_length); with none, the barrel reads 12.2. The thread's pitch, read apart from it, has the same scale within 0.4%."},"flange_od":{"label":"The barrel extension's flange, its diameter as the photo has it at the journal's scale","kind":"length","measurements":[{"id":"photo","value":1.186,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"its gas block journal's diameter, 122.58 px (columns 1432 to 1722, a line through each edge at grey 200), as the published .750 (journal_od): 163.44 px/in","method":"the silhouette's widest, columns 272 to 287: 193.8 px against the journal's 122.58","via":"harvest"}}],"note":"The scale reference of the traced outline (the silhouette's greatest height), which sets the outline's unit to the journal's own. It is not quite the flange's size (flange_d): the photo's breech end stands a little nearer the lens than its journal (extension_od), and its cut-out edge is inside the barrel's (outline_inset)."},"bore_d":{"label":"The bore's diameter (across the lands)","kind":"length","measurements":[{"id":"tdp","value":0.219,"unit":"in","pm":0.001,"stated":".219 DIA+.001","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 2 of 2, rev J: Section U-U, rifling detail at 10/1; user-supplied scan, PDF page 211","via":"user"}}]},"thread_major_d":{"label":"The muzzle thread's major diameter (its crests)","kind":"length","measurements":[{"id":"tdp","value":0.4957,"unit":"in","pm":0.0033,"stated":"1/2-28 UNEF-2A MAJOR DIA .4989/.4924","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213","via":"user"}}],"note":"The Army barrel's 1/2-28 thread, for the 1/2 X 28 the seller states: what the model's thread is drawn at."},"thread_minor_d":{"label":"The muzzle thread's minor diameter (its roots)","kind":"length","measurements":[{"id":"tdp","value":0.4551,"unit":"in","pm":0.002,"stated":"MINOR DIA .4551 MAX","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213","via":"user"}}]},"thread_pitch":{"label":"The muzzle thread's pitch","kind":"length","measurements":[{"id":"tdp","value":0.03571,"unit":"in","pm":0.00005,"stated":"1/2-28 UNEF-2A","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213","via":"user"}},{"id":"primary-arms","value":0.03571,"unit":"in","pm":0.00005,"stated":"Thread Pattern 1/2 X 28","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Bravo Company Manufacturing Chrome Lined 5.56 AR-15 Barrel - Carbine - Government - 11.5\" (BCM-BRL-S-11-STD), Specifications","url":"https://www.primaryarms.com/bravo-company-bcm-ar-15-barrel-11.5in-5.56-nato-carbine-length-govt-profile","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"primary-arms","reason":"The seller's statement for this barrel; the Army's drawing has the same thread on its own."},"note":"28 threads to the inch, by the seller's statement and the Army barrel's drawing: neither is a measurement of this barrel."},"gas_port_d":{"label":"The gas port's diameter","kind":"length","measurements":[{"id":"photo","value":0.078,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 2583fd18e700 (Primary Arms' gallery, BCM-BRL-S-11-STD_03: the gas block journal from above, close, 2200 x 1467)","scaleRef":"the journal's width across the barrel beside the port as the published .750 (journal_od): about 390 px, 520 px/in","method":"the port's mouth, an ellipse 41 px long along the barrel by 28 across (columns 1107 to 1148, rows 715 to 750): its long axis, which the view doesn't shorten","via":"harvest"}},{"id":"chart","value":0.075,"unit":"in","pm":0.01,"stated":"0.075\"ø Gas Port","source":{"type":"spec","publisher":"unknown","name":"AR-15_M4_Barrel_Dimensions.jpg in the user's TDP folder (Spec_Sheets): a third-party illustration of a 14.5 in mid-length barrel, no drawing number","via":"user"}}],"adopt":{"from":"photo","reason":"This barrel's own port, on its own photo; the chart's is another length of gas system's, and agrees within the reading."},"note":"BCM publishes none, and no drawing of a carbine's port is in the package. Read on Primary Arms' close view of this barrel's journal, a little oblique; a chart's figure for a mid-length barrel is beside it (the rifle's, 8448548, is .092)."},"index_pin_d":{"label":"The barrel indexing pin's diameter","kind":"length","measurements":[{"id":"model","value":0.125,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.index_pin_d}","via":"user"}}],"note":"A mil-spec extension's, as bcm-16-mid-barrel's ledger read it off the reference CAD set (BCM, of this barrel: \"M4 Feed Ramp Barrel Extension\"; of the 16 in one: \"M4 Feed Ramp Barrel Extension (USGI)\")."},"extension_mouth_d":{"label":"The barrel extension's rear opening, its diameter at the rear face","kind":"length","measurements":[{"id":"model","value":0.77,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_mouth_d}","via":"user"}}],"note":"The inside of a mil-spec extension as the reference CAD set has it, read once in bcm-16-mid-barrel's ledger (BCM, of this barrel: \"M4 Feed Ramp Barrel Extension\"; of the 16 in one: \"M4 Feed Ramp Barrel Extension (USGI)\"). Appearance only."},"extension_mouth_chamfer":{"label":"The rear opening's chamfer, its depth (at 45°, also how far it narrows the opening's radius)","kind":"length","measurements":[{"id":"model","value":0.045,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_mouth_chamfer}","via":"user"}}]},"extension_lug_bore_d":{"label":"The circle the extension's locking lugs leave between their tips","kind":"length","measurements":[{"id":"model","value":0.572,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_lug_bore_d}","via":"user"}}]},"extension_lug_depth":{"label":"The locking lugs' front faces, ahead of the extension's rear end","kind":"length","measurements":[{"id":"model","value":0.214,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_lug_depth}","via":"user"}}]},"extension_recess_d":{"label":"The recess ahead of the lugs, which the bolt's lugs turn in: its diameter","kind":"length","measurements":[{"id":"model","value":0.83,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_recess_d}","via":"user"}}]},"extension_recess_depth":{"label":"The recess's front end, ahead of the extension's rear end","kind":"length","measurements":[{"id":"model","value":0.595,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_recess_depth}","via":"user"}}]},"outline_rear_face":{"label":"The extension's rear face in the traced outline's own frame (from the silhouette's rear tip, at the journal's scale)","kind":"length","measurements":[{"id":"photo","value":0.046,"unit":"in","pm":0.009,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, 2200 x 1467)","scaleRef":"scale from bcm-115-carbine-barrel.flange_od = 1.186 in (y-extent 194 px → 163.6 px/in)","method":"the min end's face: the silhouette's tip at -0.000 less its rim's arc, 0.046 in of sag at radius 0.497451 (the end is seen from 5.3° off square; arc fitted over 113 rows, rms 0.002) of the traced outline (tools/trace.py); the extension's rear face in the outline's own frame (from its rear tip, at the journal's scale)","via":"harvest"}}],"note":"Where the outline is cut: the silhouette's tip is the rear rim's near side, which stands behind the face by the rim's arc."},"outline_front_face":{"label":"The muzzle's face in the traced outline's own frame (from the silhouette's rear tip, at the journal's scale)","kind":"length","measurements":[{"id":"photo","value":12.24,"unit":"in","pm":0.083,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, 2200 x 1467)","scaleRef":"scale from bcm-115-carbine-barrel.flange_od = 1.186 in (y-extent 194 px → 163.6 px/in)","method":"the max end's face: the silhouette's tip at 12.278 less its rim's arc, 0.038 in of sag at radius 0.228863 (the end is seen from 9.4° off square; arc fitted over 118 rows, rms 0.002) of the traced outline (tools/trace.py); the muzzle's face in the outline's own frame (from its rear tip, at the journal's scale)","via":"harvest"}},{"id":"rim","value":12.258,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467)","scaleRef":"the traced outline's own (flange_od): 163.6 px/in","method":"the silhouette's tip (12.278) less the arc the face's own rim makes: the crown's corner is broken (the thread's edges leave their full height 8 px before the tip, where a rim of the thread's radius seen from 5.3 degrees would take 3.7), so the face's rim is 35 px in radius and its arc 3.2 px deep, the lens 65 in off as the rear end's arc has it","via":"harvest"}}],"adopt":{"from":"rim","reason":"The tool fits one arc of the thread's own radius to the muzzle's rim and its broken corner together, and puts the face 0.02 in too far back (it has the muzzle seen from 9.4 degrees where the rear end, as far from the lens's foot, is seen from 5.3); the rim's own arc, at the lens's distance as the rear end gives it, is the face. The thread is then 0.63 in long, the Army's."},"note":"Where the outline is cut: the silhouette's front tip is the muzzle rim's near side."}}},{"subject":"bcm-145-mid-barrel","title":"BCM Standard 14.5\" Mid Length Barrel, Stripped (BCM-BRL-s-MID-14-STD)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"bcm","value":26,"unit":"oz","pm":1,"stated":"Approximate Weight: 1lb 10oz","source":{"type":"spec","publisher":"manufacturer","name":"BCM, BCM Standard 14.5\" Mid Length Barrel, Stripped (BCM-BRL-s-MID-14-STD), Description","url":"https://bravocompanyusa.com/bcm-standard-14-5-mid-length-barrel-stripped/","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":26,"unit":"oz","pm":0.5,"stated":"1 lb 10 oz weight","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Bravo Company Manufacturing Chrome Lined 5.56 AR-15 Barrel - Mid-Length - Government - 14.5\" (BCM-BRL-S-MID-14-STD), Features and Specifications","url":"https://www.primaryarms.com/bravo-company-manufacturing-5-56-nato-1-7-mid-length-govt-profile-ar-15-barrel-14-5in","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"bcm","reason":"The maker's own figure, with its own word for how exact it is; the seller's is the same weight."},"note":"\"Approximate\" is BCM's word: the ± is a whole ounce. Primary Arms states the same figure."},"length":{"label":"Barrel length as its maker states it","kind":"length","measurements":[{"id":"bcm","value":14.5,"unit":"in","pm":0.05,"stated":"These are stripped 14.5\" Mid Length Standard 11595E barrels with gas ports installed and dimpled for a strong gas block installation.","source":{"type":"spec","publisher":"manufacturer","name":"BCM, BCM Standard 14.5\" Mid Length Barrel, Stripped (BCM-BRL-s-MID-14-STD), Description","url":"https://bravocompanyusa.com/bcm-standard-14-5-mid-length-barrel-stripped/","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":14.5,"unit":"in","pm":0.05,"stated":"Barrel Length 14.5","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Bravo Company Manufacturing Chrome Lined 5.56 AR-15 Barrel - Mid-Length - Government - 14.5\" (BCM-BRL-S-MID-14-STD), Specifications","url":"https://www.primaryarms.com/bravo-company-manufacturing-5-56-nato-1-7-mid-length-govt-profile-ar-15-barrel-14-5in","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"bcm","reason":"The maker's own; the seller repeats it."},"note":"The nominal length. BCM's page doesn't say between which points; the Army's barrel drawing (8448549) dimensions a barrel from its breech end, inside the extension, to its muzzle, and overall_length takes it so."},"journal_od":{"label":"The gas block journal's diameter","kind":"length","measurements":[{"id":"bcm","value":0.75,"unit":"in","pm":0.0005,"stated":"(.750) at Gas Block location","source":{"type":"spec","publisher":"manufacturer","name":"BCM, BCM Standard 14.5\" Mid Length Barrel, Stripped (BCM-BRL-s-MID-14-STD), Description","url":"https://bravocompanyusa.com/bcm-standard-14-5-mid-length-barrel-stripped/","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":0.75,"unit":"in","pm":0.0005,"stated":"Gas Seat Diameter .750","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Bravo Company Manufacturing Chrome Lined 5.56 AR-15 Barrel - Mid-Length - Government - 14.5\" (BCM-BRL-S-MID-14-STD), Specifications","url":"https://www.primaryarms.com/bravo-company-manufacturing-5-56-nato-1-7-mid-length-govt-profile-ar-15-barrel-14-5in","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"bcm","reason":"The maker's own; the seller repeats it."}},"extension_behind_breech":{"label":"The barrel extension's rear end behind the barrel's breech end","kind":"length","measurements":[{"id":"model","value":0.501,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{std.ar15.barrel_extension_behind_breech}","via":"user"}}],"note":"The standard's: the reference CAD set's extension less the Army's .620 tenon (std.ar15.barrel_extension_behind_breech), the one figure the catalog's 5.56 barrels take their breech from. BCM: \"M4 Feed Ramp Barrel Extension (USGI)\"."},"overall_length":{"label":"End to end, the extension's rear to the muzzle","kind":"length","measurements":[{"id":"photo","value":15.23,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/bcm-145-mid-barrel c7e2f77b39f5 (Primary Arms' gallery, BCM-BRL-S-MID-14-STD_02: the barrel level on white, seen from above, the muzzle at the right, 2200 x 1467)","scaleRef":"its extension's body as the Army's .999 (extension_od) and its journal as the published .750 (journal_od)","method":"its two end faces, each behind its rim's arc (columns 122.8 and 2093.1: outline_rear_face, outline_front_face), at the scales its extension's body and its journal give with their edges read at grey 200 and no allowance for the cut-out's edge (127.90 px/in at column 178, 130.09 at 1528, a straight line between and beyond)","via":"harvest"}},{"id":"thread","value":15.19,"unit":"in","pm":0.1,"source":{"type":"photo","photo":"references/bcm-145-mid-barrel c7e2f77b39f5 (Primary Arms' gallery, BCM-BRL-S-MID-14-STD_02: the barrel level on white, seen from above, the muzzle at the right, 2200 x 1467)","scaleRef":"its muzzle thread's pitch as 28 to the inch (thread_pitch), with its extension's body and its journal","method":"the same two faces, with the thread as the ruler: the calibration fixed by the two diameters and by 28 threads to the inch at the muzzle (4.77 px a thread on rows just inside each edge, columns 2030 to 2090; the spectrum's peak, 4.74 to 4.83 by the row) in place of the published length","via":"harvest"}},{"id":"published","value":15.001,"unit":"in","pm":0.07,"source":{"type":"derived","expr":"{.length} + {.extension_behind_breech}","via":"harvest"}}],"adopt":{"from":"published","reason":"The maker's length: the site's line on the law goes by it, and the photo's calibration is fixed by it. The two readings that don't use it are 1.3 and 1.5% longer, each for a reason of its own (the thread's pitch read over 60 px of a close photo; the cut-out's edge)."},"note":"The published length is the scale for lengths: it is one of the three knowns the photo's calibration is fixed by, with the extension's body (the Army's .999) and the journal (.750). The two diameters alone, their edges read at grey 200, have the barrel 1.5% longer (the 16 in barrel's photo read 2.5% longer the same way: a black tube reads thin on white); what closes it is 0.79 px on each edge, a cut-out's width. The checks that are not among the three: the thread's silhouette comes out at 0.496 (the Army's crests .4957), the flange at 1.167 (the reference CAD set's 1.170), the extension 0.984 long behind its flange (0.990), the gas port at 9.10 (the three 16 in barrels' 9.13 to 9.17) and 0.286 ahead of the collar (BCM's own gas block: 0.275 from its rear face to its port), the thread 0.61 long (the Army's .63), and the thread's own pitch, 4.77 px, where the calibration expects 4.83: 1.3% apart, which is the second measurement here. The 11.5 in barrel's photo, taken from four times as far, closes the same way within 0.4%. The ± of the published one covers whether the 14.5 is from the barrel's breech end (the Army's drawing) or from the bolt's face, an eighth further back."},"extension_rear_x":{"label":"The barrel extension's rear end, from the flange's rear face (negative: inside the receiver)","kind":"length","measurements":[{"id":"photo","value":-0.984,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-145-mid-barrel c7e2f77b39f5 (Primary Arms' gallery, BCM-BRL-S-MID-14-STD_02: the barrel level on white, seen from above, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 131.34 px/in opposite the lens at column 1100 and 2.02 px/in more per 1000 px toward the muzzle, the cut-out's edge 0.79 px inside the barrel's); 127.9 px/in along the axis there","method":"the rear end's face (column 122.8: outline_rear_face, behind its rim's arc) to the flange's rear face (column 248.5): where the flange's edges reach their full height; before it the edge is the rim's near arc, from column 232.5","via":"harvest"}}],"note":"The reference CAD set's extension has 0.990 here (1.121 less its 0.131 flange), and the 16 in barrel's own photo 0.984."},"flange_front_x":{"label":"The extension flange's front face, ahead of its rear face (the flange's thickness)","kind":"length","measurements":[{"id":"photo","value":0.102,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-145-mid-barrel c7e2f77b39f5 (Primary Arms' gallery, BCM-BRL-S-MID-14-STD_02: the barrel level on white, seen from above, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 131.34 px/in opposite the lens at column 1100 and 2.02 px/in more per 1000 px toward the muzzle, the cut-out's edge 0.79 px inside the barrel's); 128.0 px/in along the axis there","method":"the flange's rear face (column 248.5) to where its edges stop being level (column 261.5)","via":"harvest"}}],"note":"The reference CAD set's flange is 0.131 thick; this one reads thinner, as the 16 in barrel's did (0.095). Ahead of the face the silhouette's corner is the rim's far arc, seen past the barrel (to column 277.5, 16 px on, as an ellipse seen from 21 degrees should be)."},"flange_d":{"label":"The barrel extension's flange, its diameter","kind":"length","measurements":[{"id":"photo","value":1.167,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/bcm-145-mid-barrel c7e2f77b39f5 (Primary Arms' gallery, BCM-BRL-S-MID-14-STD_02: the barrel level on white, seen from above, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 131.34 px/in opposite the lens at column 1100 and 2.02 px/in more per 1000 px toward the muzzle, the cut-out's edge 0.79 px inside the barrel's); 129.64 px/in there","method":"the silhouette's widest, columns 249 to 260: 149.7 px, with the cut-out's 1.58 px","via":"harvest"}}],"note":"The reference CAD set's is 1.170. (flange_od is this same height at the journal's scale alone, the outline's scale reference.)"},"extension_od":{"label":"The barrel extension's body, its diameter (what goes into the receiver)","kind":"length","measurements":[{"id":"tdp","value":0.999,"unit":"in","pm":0.001,"stated":"DIAMETER NOT TO EXCEED .9990 FOR THIS LENGTH AFTER ASSEMBLY AND BEFORE FINISH","source":{"type":"standard","doc":"US Army TDP drawing 8448548 (Barrel and Barrel Extension Assembly), rev N: the assembly's side view at 1/1; user-supplied scan, PDF page 212","via":"user"},"note":"An upper limit: it goes into the receiver's 1.000 bore (8448524). The reference CAD set's extension is .9987."},{"id":"photo","value":0.982,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/bcm-145-mid-barrel c7e2f77b39f5 (Primary Arms' gallery, BCM-BRL-S-MID-14-STD_02: the barrel level on white, seen from above, the muzzle at the right, 2200 x 1467)","scaleRef":"its gas block journal's diameter as the published .750 (journal_od): 130.09 px/in","method":"the extension's body, columns 130 to 225: 127.77 px against the journal's 97.57 (a line through each edge at grey 200)","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's limit: an extension over 1.000 doesn't go into a receiver. The photo reads 1.7% small here because its breech end is further from the lens than its journal."},"note":"The photo's reading says how square the photo is, not how big the extension is: at the journal's scale it is 1.7% small, the breech end standing further from the lens than the journal. It is one of the three knowns the photo's calibration is fixed by (with the journal's .750 and the published length), so the model draws it at the drawing's."},"chamber_od":{"label":"The chamber section's diameter (between the flange and the taper)","kind":"length","measurements":[{"id":"photo","value":0.98,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/bcm-145-mid-barrel c7e2f77b39f5 (Primary Arms' gallery, BCM-BRL-S-MID-14-STD_02: the barrel level on white, seen from above, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 131.34 px/in opposite the lens at column 1100 and 2.02 px/in more per 1000 px toward the muzzle, the cut-out's edge 0.79 px inside the barrel's); 129.76 px/in there","method":"columns 286 to 340: 125.62 px (a line through each edge at grey 200), with the cut-out's 1.58 px","via":"harvest"}}],"note":"The 16 in barrel's own photo has 0.99 here at its journal's scale, read 1.2% large."},"taper_rear_x":{"label":"Where the taper ahead of the chamber section begins, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":0.777,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-145-mid-barrel c7e2f77b39f5 (Primary Arms' gallery, BCM-BRL-S-MID-14-STD_02: the barrel level on white, seen from above, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 131.34 px/in opposite the lens at column 1100 and 2.02 px/in more per 1000 px toward the muzzle, the cut-out's edge 0.79 px inside the barrel's); 128.3 px/in along the axis there","method":"the flange's rear face (column 248.5) to where the straight taper's edges, carried back, meet the chamber section's (column 348)","via":"harvest"}}]},"taper_front_x":{"label":"Where the taper ends and the section under the handguard begins, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":1.627,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-145-mid-barrel c7e2f77b39f5 (Primary Arms' gallery, BCM-BRL-S-MID-14-STD_02: the barrel level on white, seen from above, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 131.34 px/in opposite the lens at column 1100 and 2.02 px/in more per 1000 px toward the muzzle, the cut-out's edge 0.79 px inside the barrel's); 128.8 px/in along the axis there","method":"the flange's rear face (column 248.5) to where the taper's edges meet the section's ahead (column 457.3)","via":"harvest"}}],"note":"A straight cone: its edges are lines within half a pixel from column 352 to 455."},"handguard_rear_od":{"label":"The section under the handguard, its diameter at its rear end (the taper's foot)","kind":"length","measurements":[{"id":"photo","value":0.676,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-145-mid-barrel c7e2f77b39f5 (Primary Arms' gallery, BCM-BRL-S-MID-14-STD_02: the barrel level on white, seen from above, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 131.34 px/in opposite the lens at column 1100 and 2.02 px/in more per 1000 px toward the muzzle, the cut-out's edge 0.79 px inside the barrel's); 130.07 px/in there","method":"a line through each edge over columns 470 to 860, carried to column 470: 86.3 px, with the cut-out's 1.58 px","via":"harvest"}}],"note":"The section narrows toward the muzzle (the 16 in barrel's does too, .680 to .652 by its own photo): by more than the photo's lean, which runs the other way."},"handguard_front_od":{"label":"The section under the handguard, its diameter at its front end (where the ramp to the collar begins)","kind":"length","measurements":[{"id":"photo","value":0.651,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-145-mid-barrel c7e2f77b39f5 (Primary Arms' gallery, BCM-BRL-S-MID-14-STD_02: the barrel level on white, seen from above, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 131.34 px/in opposite the lens at column 1100 and 2.02 px/in more per 1000 px toward the muzzle, the cut-out's edge 0.79 px inside the barrel's); 131.65 px/in there","method":"a line through each edge over columns 860 to 1255, carried to column 1252: 84.16 px, with the cut-out's 1.58 px","via":"harvest"}}]},"ramp_rear_x":{"label":"Where the ramp up to the collar begins, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":7.746,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-145-mid-barrel c7e2f77b39f5 (Primary Arms' gallery, BCM-BRL-S-MID-14-STD_02: the barrel level on white, seen from above, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 131.34 px/in opposite the lens at column 1100 and 2.02 px/in more per 1000 px toward the muzzle, the cut-out's edge 0.79 px inside the barrel's); 132.0 px/in along the axis there","method":"the flange's rear face (column 248.5) to where the edges leave the section's line (column 1255)","via":"harvest"}}],"note":"A concave ramp, steepening to a sharp corner at the collar's full diameter."},"ramp_mid_x":{"label":"A station midway up the ramp, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":7.977,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-145-mid-barrel c7e2f77b39f5 (Primary Arms' gallery, BCM-BRL-S-MID-14-STD_02: the barrel level on white, seen from above, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 131.34 px/in opposite the lens at column 1100 and 2.02 px/in more per 1000 px toward the muzzle, the cut-out's edge 0.79 px inside the barrel's); 132.1 px/in along the axis there","method":"the flange's rear face (column 248.5) to column 1285.5","via":"harvest"}}],"note":"With ramp_mid_od: the third point the model's arc is put through."},"ramp_mid_od":{"label":"The ramp's diameter at that station","kind":"length","measurements":[{"id":"photo","value":0.712,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/bcm-145-mid-barrel c7e2f77b39f5 (Primary Arms' gallery, BCM-BRL-S-MID-14-STD_02: the barrel level on white, seen from above, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 131.34 px/in opposite the lens at column 1100 and 2.02 px/in more per 1000 px toward the muzzle, the cut-out's edge 0.79 px inside the barrel's); 131.72 px/in there","method":"columns 1285 and 1286: 92.2 px, with the cut-out's 1.58 px","via":"harvest"}}]},"collar_rear_x":{"label":"Where the collar reaches its full diameter (the ramp's top), ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":8.204,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-145-mid-barrel c7e2f77b39f5 (Primary Arms' gallery, BCM-BRL-S-MID-14-STD_02: the barrel level on white, seen from above, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 131.34 px/in opposite the lens at column 1100 and 2.02 px/in more per 1000 px toward the muzzle, the cut-out's edge 0.79 px inside the barrel's); 132.2 px/in along the axis there","method":"the flange's rear face (column 248.5) to where the edges become level (column 1315.5)","via":"harvest"}}]},"collar_od":{"label":"The collar behind the gas block journal, its diameter","kind":"length","measurements":[{"id":"photo","value":0.853,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-145-mid-barrel c7e2f77b39f5 (Primary Arms' gallery, BCM-BRL-S-MID-14-STD_02: the barrel level on white, seen from above, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 131.34 px/in opposite the lens at column 1100 and 2.02 px/in more per 1000 px toward the muzzle, the cut-out's edge 0.79 px inside the barrel's); 131.86 px/in there","method":"columns 1322 to 1395: 110.96 px (a line through each edge at grey 200), with the cut-out's 1.58 px","via":"harvest"}}],"note":"What a gas block's rear face comes back to. The 16 in barrel's reads 0.86 by its own photo."},"journal_rear_x":{"label":"The gas block journal's rear shoulder (the collar's front face) ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":8.812,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-145-mid-barrel c7e2f77b39f5 (Primary Arms' gallery, BCM-BRL-S-MID-14-STD_02: the barrel level on white, seen from above, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 131.34 px/in opposite the lens at column 1100 and 2.02 px/in more per 1000 px toward the muzzle, the cut-out's edge 0.79 px inside the barrel's); 132.5 px/in along the axis there","method":"the flange's rear face (column 248.5) to the collar's front face (column 1396): where its edges begin to fall; the fall is its rim's near arc, an ellipse 7.4 px deep seen past the journal for 3.5 px, and the edge follows it to column 1399.5","via":"harvest"}}],"note":"A gas block's rear face comes back to this shoulder. The 16 in barrel's is at 8.848 by its own photo, Aero's at 8.87, Bear Creek's at 8.85."},"gas_port_x":{"label":"The gas port ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":9.098,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/bcm-145-mid-barrel c7e2f77b39f5 (Primary Arms' gallery, BCM-BRL-S-MID-14-STD_02: the barrel level on white, seen from above, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 131.34 px/in opposite the lens at column 1100 and 2.02 px/in more per 1000 px toward the muzzle, the cut-out's edge 0.79 px inside the barrel's); 132.7 px/in along the axis there","method":"the flange's rear face (column 248.5) to the middle of the port's mouth (column 1441.5, row 734.5: a dark spot 8 px across inside a lighter ring of 13), brought back to the axis's depth (column 1433.8)","via":"harvest"}}],"note":"BCM says \"gas ports installed and dimpled\" and gives no distance. The port faces the lens in this photo, so its mouth is seen 0.375 in nearer than the axis and stands off toward the picture's edge by 7.7 px (0.06 in): taken out, with the lens 16.7 in off (a further inch either way moves it 0.003). 0.29 ahead of the journal's rear shoulder, as the 16 in barrel's is (8448548 has .295 on the rifle's barrel; a mid-length chart .300), and where BCM's own gas block has its port ahead of its rear face (0.275). Checks: the 16 in barrel's port is at 9.13 by its own photo, Aero's at 9.17, Bear Creek's at 9.14; the chart in the TDP's folder (AR-15_M4_Barrel_Dimensions.jpg, a third-party illustration) puts a mid-length port 9.050 ahead of the extension's front face, 9.15 from this one with this flange's 0.102. The ± covers the calibration's own doubt along the barrel (the thread's pitch has the muzzle end's scale 1.3% smaller: overall_length)."},"journal_front_x":{"label":"The gas block journal's front end (where the barrel steps down) ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":10.736,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-145-mid-barrel c7e2f77b39f5 (Primary Arms' gallery, BCM-BRL-S-MID-14-STD_02: the barrel level on white, seen from above, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 131.34 px/in opposite the lens at column 1100 and 2.02 px/in more per 1000 px toward the muzzle, the cut-out's edge 0.79 px inside the barrel's); 133.6 px/in along the axis there","method":"the flange's rear face (column 248.5) to the journal's front face (column 1652): where its edges begin to fall, on its rim's near arc (12 px deep, seen for 3.6 px, to column 1656)","via":"harvest"}}],"note":"The journal is 1.92 long: long enough for a front sight base's two bands."},"mid_od":{"label":"The diameter ahead of the journal (between its front end and the step behind the muzzle)","kind":"length","measurements":[{"id":"photo","value":0.718,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-145-mid-barrel c7e2f77b39f5 (Primary Arms' gallery, BCM-BRL-S-MID-14-STD_02: the barrel level on white, seen from above, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 131.34 px/in opposite the lens at column 1100 and 2.02 px/in more per 1000 px toward the muzzle, the cut-out's edge 0.79 px inside the barrel's); 132.75 px/in there","method":"columns 1665 to 1930: 93.74 px (a line through each edge at grey 200), with the cut-out's 1.58 px","via":"harvest"}}],"note":"The marking \"HP MP 1/7 5.56 NATO\" is on this section. The 16 in barrel's reads 0.716 to 0.709."},"step_x":{"label":"The step behind the muzzle (where the last section begins) ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":12.84,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-145-mid-barrel c7e2f77b39f5 (Primary Arms' gallery, BCM-BRL-S-MID-14-STD_02: the barrel level on white, seen from above, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 131.34 px/in opposite the lens at column 1100 and 2.02 px/in more per 1000 px toward the muzzle, the cut-out's edge 0.79 px inside the barrel's); 134.7 px/in along the axis there","method":"the flange's rear face (column 248.5) to the step's face (column 1934.2): where the edges begin to fall, on its rim's near arc (18 px deep, seen for 4.4 px, to column 1939)","via":"harvest"}}]},"muzzle_od":{"label":"The diameter behind the muzzle thread","kind":"length","measurements":[{"id":"photo","value":0.7,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/bcm-145-mid-barrel c7e2f77b39f5 (Primary Arms' gallery, BCM-BRL-S-MID-14-STD_02: the barrel level on white, seen from above, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 131.34 px/in opposite the lens at column 1100 and 2.02 px/in more per 1000 px toward the muzzle, the cut-out's edge 0.79 px inside the barrel's); 133.11 px/in there","method":"columns 1950 to 2008: 91.57 px at their middle (a line through each edge at grey 200), with the cut-out's 1.58 px","via":"harvest"}}],"note":"The last section before the shoulder, 0.56 long. Its edges open 1.2 px toward the shoulder (0.695 to 0.704): drawn at its middle."},"shoulder_x":{"label":"The muzzle shoulder ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":13.403,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-145-mid-barrel c7e2f77b39f5 (Primary Arms' gallery, BCM-BRL-S-MID-14-STD_02: the barrel level on white, seen from above, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 131.34 px/in opposite the lens at column 1100 and 2.02 px/in more per 1000 px toward the muzzle, the cut-out's edge 0.79 px inside the barrel's); 135.0 px/in along the axis there","method":"the flange's rear face (column 248.5) to the shoulder's face (column 2010.2): where that ellipse begins, fitted to the edges as they fall over columns 2012 to 2018 (0.5 px down at 2 px on, 2 at 4, 4.5 at 6, 8 at 8)","via":"harvest"}}],"note":"Where the thread begins: a muzzle device or its washer seats here. The corner ahead of it in the silhouette is its rim's near arc: the lens sees the muzzle end from 22 degrees off square, and the rim's ellipse, 19 px deep, stands past the thread for 13 px, to column 2023.5."},"thread_length":{"label":"The muzzle thread's length","kind":"length","measurements":[{"id":"photo","value":0.614,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-145-mid-barrel c7e2f77b39f5 (Primary Arms' gallery, BCM-BRL-S-MID-14-STD_02: the barrel level on white, seen from above, the muzzle at the right, 2200 x 1467)","scaleRef":"the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 131.34 px/in opposite the lens at column 1100 and 2.02 px/in more per 1000 px toward the muzzle, the cut-out's edge 0.79 px inside the barrel's); 135.4 px/in along the axis there","method":"the shoulder's face (column 2010.2) to the muzzle's face (column 2093.1: outline_front_face, behind its rim's arc and its crown's break)","via":"harvest"}}],"note":"The Army's is .63 (8448549 sheet 1, from the shoulder to the muzzle; a mid-length chart has .624); the 11.5 in barrel's own photo reads 0.63, the 16 in barrel's 0.50. The thread's own pitch reads 4.77 px here (rows just inside each edge, columns 2030 to 2090), which is 28 to the inch at 133.6 px/in where the calibration has 135.2: by the thread as the ruler it is 0.62."},"index_pin_x":{"label":"The barrel indexing pin's axis behind the flange's rear face","kind":"length","measurements":[{"id":"photo","value":0.086,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-145-mid-barrel c7e2f77b39f5 (Primary Arms' gallery, BCM-BRL-S-MID-14-STD_02: the barrel level on white, seen from above, the muzzle at the right, 2200 x 1467)","scaleRef":"the scale at the rim's depth, 0.58 in nearer the lens than the axis (16.7 in off): 134.3 px/in","method":"the pin's head (columns 203 to 218 on rows 722 to 738: its middle at 210.5) against the flange's rear rim where it passes nearest the lens (column 222): 11.5 px","via":"harvest"}}],"note":"The pin faces the lens in this photo, its head as far out as the flange's rim: the two are compared in one plane. The reference CAD set has 0.0765 (0.2075 behind the flange's front face, less its 0.131 flange); the 11.5 in barrel's own photo 0.081, the 16 in barrel's 0.113."},"index_pin_top":{"label":"The barrel indexing pin's top above the bore's axis","kind":"length","measurements":[{"id":"sibling","value":0.584,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.index_pin_top}","via":"harvest"}}],"note":"Not seen in profile in any photo of this barrel (the level one looks down on it). The same extension by BCM's words for both (\"M4 Feed Ramp Barrel Extension (USGI)\"): the 16 in barrel's reading, off its own side photo, by reference. (The 11.5 in barrel's own photo has its pin at 0.594.)"},"outline_lens_x":{"label":"The photo's calibration: the lens's foot along the traced outline (in the outline's own frame, from the silhouette's rear tip)","kind":"length","measurements":[{"id":"photo","value":7.707,"unit":"in","pm":0.15,"source":{"type":"photo","photo":"references/bcm-145-mid-barrel c7e2f77b39f5 (Primary Arms' gallery, BCM-BRL-S-MID-14-STD_02: the barrel level on white, seen from above, the muzzle at the right, 2200 x 1467)","scaleRef":"the traced outline's own (flange_od): 130.4 px/in","method":"column 1100 of 2200, in the outline's unit (130.4 px/in from its tip at column 95.0)","via":"harvest"}}],"note":"The picture's middle. Every seam of the barrel shows as an arc, and the arcs turn over there: the flange's rim bulges toward the breech (26 px on a radius of 75), the collar's front face, the two steps and the shoulder toward the muzzle (7 to 19 px), in proportion to their distance from column 1100. The rear end's arc (outline_rear_face: seen from 23.7 degrees) puts the lens 17.2 in off, the muzzle's about 16.7 with the barrel's lean."},"outline_yaw_run":{"label":"The photo's calibration: how fast its scale grows toward the muzzle (the scale is 1 + (x - outline_lens_x) / this, x along the traced outline)","kind":"length","measurements":[{"id":"photo","value":500,"unit":"in","pm":60,"source":{"type":"photo","photo":"references/bcm-145-mid-barrel c7e2f77b39f5 (Primary Arms' gallery, BCM-BRL-S-MID-14-STD_02: the barrel level on white, seen from above, the muzzle at the right, 2200 x 1467)","scaleRef":"its extension's body (extension_od) and its journal (journal_od)","method":"the extension's body (127.77 px at column 178) as the Army's .999 and the journal (97.57 px at column 1528) as the published .750, each with the cut-out's 1.58 px: 129.48 and 132.21 px/in, 1350 px apart","via":"harvest"}}],"note":"The barrel leans 1.9 degrees to the lens, its muzzle nearer: the extension's body reads 1.7% small against the journal. A lean changes a diameter's scale in a straight line along the picture, and a length's twice as fast (a point of the axis at x is (x - outline_lens_x) / scale from the lens's foot). The scale grows 3.1% from the rear face to the muzzle."},"outline_inset":{"label":"The photo's calibration: how far inside the barrel's edge the cut-out's edge at grey 200 stands, on each side (in the outline's unit)","kind":"length","measurements":[{"id":"photo","value":0.0061,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/bcm-145-mid-barrel c7e2f77b39f5 (Primary Arms' gallery, BCM-BRL-S-MID-14-STD_02: the barrel level on white, seen from above, the muzzle at the right, 2200 x 1467)","scaleRef":"its extension's body (extension_od), its journal (journal_od) and its published length (overall_length)","method":"solved: the length between the end faces (columns 122.8 and 2093.1) at the scales the extension's body and the journal give is 15.001 with 1.58 px added to every width, 15.226 with none","via":"harvest"}}],"note":"0.79 px. What makes the two known diameters' scales give the published length between the end faces (overall_length); with none, the barrel reads 15.23."},"flange_od":{"label":"The barrel extension's flange, its diameter as the photo has it at the journal's scale","kind":"length","measurements":[{"id":"photo","value":1.151,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/bcm-145-mid-barrel c7e2f77b39f5 (Primary Arms' gallery, BCM-BRL-S-MID-14-STD_02: the barrel level on white, seen from above, the muzzle at the right, 2200 x 1467)","scaleRef":"its gas block journal's diameter, 97.57 px (columns 1410 to 1645, a line through each edge at grey 200), as the published .750 (journal_od): 130.09 px/in","method":"the silhouette's widest, columns 249 to 260: 149.7 px against the journal's 97.57","via":"harvest"}}],"note":"The scale reference of the traced outline (the silhouette's greatest height), which sets the outline's unit to the journal's own: 130.1 px to the inch. It is not the flange's size: the photo's breech end stands further from the lens than its journal (extension_od), and its cut-out edge is a little inside the barrel's (outline_inset). Corrected for both, the flange is 1.166; the reference CAD set's is 1.170."},"bore_d":{"label":"The bore's diameter (across the lands)","kind":"length","measurements":[{"id":"tdp","value":0.219,"unit":"in","pm":0.001,"stated":".219 DIA+.001","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 2 of 2, rev J: Section U-U, rifling detail at 10/1; user-supplied scan, PDF page 211","via":"user"}}]},"thread_major_d":{"label":"The muzzle thread's major diameter (its crests)","kind":"length","measurements":[{"id":"tdp","value":0.4957,"unit":"in","pm":0.0033,"stated":"1/2-28 UNEF-2A MAJOR DIA .4989/.4924","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213","via":"user"}}],"note":"The Army barrel's 1/2-28 thread, for the 1/2 X 28 the seller states: what the model's thread is drawn at. The photo's silhouette of the thread is 0.496 once corrected (64.5 px at grey 200), on its crests."},"thread_minor_d":{"label":"The muzzle thread's minor diameter (its roots)","kind":"length","measurements":[{"id":"tdp","value":0.4551,"unit":"in","pm":0.002,"stated":"MINOR DIA .4551 MAX","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213","via":"user"}}]},"thread_pitch":{"label":"The muzzle thread's pitch","kind":"length","measurements":[{"id":"tdp","value":0.03571,"unit":"in","pm":0.00005,"stated":"1/2-28 UNEF-2A","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213","via":"user"}},{"id":"primary-arms","value":0.03571,"unit":"in","pm":0.00005,"stated":"Thread Pattern 1/2 X 28","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Bravo Company Manufacturing Chrome Lined 5.56 AR-15 Barrel - Mid-Length - Government - 14.5\" (BCM-BRL-S-MID-14-STD), Specifications","url":"https://www.primaryarms.com/bravo-company-manufacturing-5-56-nato-1-7-mid-length-govt-profile-ar-15-barrel-14-5in","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"primary-arms","reason":"The seller's statement for this barrel; the Army's drawing has the same thread on its own."},"note":"28 threads to the inch, by the seller's statement and the Army barrel's drawing: neither is a measurement of this barrel."},"gas_port_d":{"label":"The gas port's diameter","kind":"length","measurements":[{"id":"chart","value":0.075,"unit":"in","pm":0.01,"stated":"0.075\"ø Gas Port","source":{"type":"spec","publisher":"unknown","name":"AR-15_M4_Barrel_Dimensions.jpg in the user's TDP folder (Spec_Sheets): a third-party illustration of a 14.5 in mid-length barrel, no drawing number","via":"user"}}],"note":"BCM publishes none. A mid-length chart's figure, for the hole the model cuts; the rifle's (8448548) is .092. In the photo the port's mouth is a dark spot about 8 px across, 0.06 in, inside a lighter ring: not a measurement of the drilled hole."},"index_pin_d":{"label":"The barrel indexing pin's diameter","kind":"length","measurements":[{"id":"model","value":0.125,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.index_pin_d}","via":"user"}}],"note":"A mil-spec extension's, as bcm-16-mid-barrel's ledger read it off the reference CAD set (BCM, of both barrels: \"M4 Feed Ramp Barrel Extension (USGI)\")."},"extension_mouth_d":{"label":"The barrel extension's rear opening, its diameter at the rear face","kind":"length","measurements":[{"id":"model","value":0.77,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_mouth_d}","via":"user"}}],"note":"The inside of a mil-spec extension as the reference CAD set has it, read once in bcm-16-mid-barrel's ledger (BCM, of both barrels: \"M4 Feed Ramp Barrel Extension (USGI)\"). Appearance only."},"extension_mouth_chamfer":{"label":"The rear opening's chamfer, its depth (at 45°, also how far it narrows the opening's radius)","kind":"length","measurements":[{"id":"model","value":0.045,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_mouth_chamfer}","via":"user"}}]},"extension_lug_bore_d":{"label":"The circle the extension's locking lugs leave between their tips","kind":"length","measurements":[{"id":"model","value":0.572,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_lug_bore_d}","via":"user"}}]},"extension_lug_depth":{"label":"The locking lugs' front faces, ahead of the extension's rear end","kind":"length","measurements":[{"id":"model","value":0.214,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_lug_depth}","via":"user"}}]},"extension_recess_d":{"label":"The recess ahead of the lugs, which the bolt's lugs turn in: its diameter","kind":"length","measurements":[{"id":"model","value":0.83,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_recess_d}","via":"user"}}]},"extension_recess_depth":{"label":"The recess's front end, ahead of the extension's rear end","kind":"length","measurements":[{"id":"model","value":0.595,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_recess_depth}","via":"user"}}]},"outline_rear_face":{"label":"The extension's rear face in the traced outline's own frame (from the silhouette's rear tip, at the journal's scale)","kind":"length","measurements":[{"id":"photo","value":0.213,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/bcm-145-mid-barrel c7e2f77b39f5 (Primary Arms' gallery, BCM-BRL-S-MID-14-STD_02: the barrel level on white, from above, 2200 x 1467)","scaleRef":"scale from bcm-145-mid-barrel.flange_od = 1.151 in (y-extent 150 px → 130.4 px/in)","method":"the min end's face: the silhouette's tip at -0.001 less its rim's arc, 0.214 in of sag at radius 0.487097 (the end is seen from 23.7° off square; arc fitted over 121 rows, rms 0.002) of the traced outline (tools/trace.py); the extension's rear face in the outline's own frame (from its rear tip, at the journal's scale)","via":"harvest"}}],"note":"Where the outline is cut: the silhouette's tip is the rear rim's near side, which stands behind the face by the rim's arc."},"outline_front_face":{"label":"The muzzle's face in the traced outline's own frame (from the silhouette's rear tip, at the journal's scale)","kind":"length","measurements":[{"id":"photo","value":15.303,"unit":"in","pm":0.107,"source":{"type":"photo","photo":"references/bcm-145-mid-barrel c7e2f77b39f5 (Primary Arms' gallery, BCM-BRL-S-MID-14-STD_02: the barrel level on white, from above, 2200 x 1467)","scaleRef":"scale from bcm-145-mid-barrel.flange_od = 1.151 in (y-extent 150 px → 130.4 px/in)","method":"the max end's face: the silhouette's tip at 15.418 less its rim's arc, 0.115 in of sag at radius 0.244343 (the end is seen from 25.3° off square; arc fitted over 119 rows, rms 0.003) of the traced outline (tools/trace.py); the muzzle's face in the outline's own frame (from its rear tip, at the journal's scale)","via":"harvest"}},{"id":"rim","value":15.323,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/bcm-145-mid-barrel c7e2f77b39f5 (Primary Arms' gallery, BCM-BRL-S-MID-14-STD_02: the barrel level on white, seen from above, the muzzle at the right, 2200 x 1467)","scaleRef":"the traced outline's own (flange_od): 130.4 px/in","method":"the silhouette's tip (15.417) less the arc the face's own rim makes: the crown's corner is broken (the thread's edges leave their full height 17 px before the tip, where a rim of the thread's radius seen from 24 degrees would take 14), so the face's rim is 28 px in radius and its arc 12.3 px deep, the lens 16.7 in off the muzzle (the rear end's arc has it 17.2 in off, and the barrel leans 1.9 degrees, its muzzle nearer)","via":"harvest"}}],"adopt":{"from":"rim","reason":"The tool fits one arc of the thread's own radius to the muzzle's rim and its broken corner together, and puts the face 0.02 in too far back; the rim's own arc, at the lens's distance as the rear end gives it, is the face. The thread is then 0.61 in long, the Army's .63 within the reading."},"note":"Where the outline is cut: the silhouette's front tip is the muzzle rim's near side."}}},{"subject":"bcm-16-mid-barrel","title":"BCM Standard 16\" Mid Length Barrel, Stripped (BCM-BRL-s-MID-16-STD)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"bcm","value":28,"unit":"oz","pm":1,"stated":"Approximate Weight: 1lb 12oz.","source":{"type":"spec","publisher":"manufacturer","name":"BCM, BCM Standard 16\" Mid Length Barrel, Stripped (BCM-BRL-s-MID-16-STD), Description","url":"https://bravocompanyusa.com/bcm-standard-16-mid-length-barrel-stripped/","retrieved":"2026-10-05","via":"harvest"}},{"id":"primary-arms","value":1.75,"unit":"lb","pm":0.005,"stated":"1.75 lbs weight","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Bravo Company Manufacturing Chrome Lined 5.56 AR-15 Barrel - Mid-Length - Government - 16\" (BCM-BRL-S-MID-16-STD), Features and Specifications","url":"https://www.primaryarms.com/bravo-company-manufacturing-standard-16-mid-length-barrel-stripped-bcm-brl-s-mid-16-std","retrieved":"2026-10-05","via":"harvest"}}],"adopt":{"from":"bcm","reason":"The maker's own figure, with its own word for how exact it is; the seller's is the same weight in pounds."},"note":"\"Approximate\" is BCM's word: the ± is a whole ounce. Primary Arms' 1.75 lb is the same figure."},"length":{"label":"Barrel length as its maker states it","kind":"length","measurements":[{"id":"bcm","value":16,"unit":"in","pm":0.1,"stated":"These are stripped 16\" Mid Length Standard 11595E barrels with gas ports installed and dimpled for a strong gas block installation.","source":{"type":"spec","publisher":"manufacturer","name":"BCM, BCM Standard 16\" Mid Length Barrel, Stripped (BCM-BRL-s-MID-16-STD), Description","url":"https://bravocompanyusa.com/bcm-standard-16-mid-length-barrel-stripped/","retrieved":"2026-10-05","via":"harvest"}},{"id":"primary-arms","value":16,"unit":"in","pm":0.1,"stated":"Barrel Length 16","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Bravo Company Manufacturing Chrome Lined 5.56 AR-15 Barrel - Mid-Length - Government - 16\" (BCM-BRL-S-MID-16-STD), Specifications","url":"https://www.primaryarms.com/bravo-company-manufacturing-standard-16-mid-length-barrel-stripped-bcm-brl-s-mid-16-std","retrieved":"2026-10-05","via":"harvest"}}],"adopt":{"from":"bcm","reason":"The maker's own; the seller repeats it."},"note":"The nominal length. BCM's page doesn't say between which points; the Army's barrel drawing (8448549) dimensions a barrel from its breech end, inside the extension, to its muzzle, and overall_length takes it so."},"journal_od":{"label":"The gas block journal's diameter","kind":"length","measurements":[{"id":"bcm","value":0.75,"unit":"in","pm":0.0005,"stated":"(.750) at Gas Block location","source":{"type":"spec","publisher":"manufacturer","name":"BCM, BCM Standard 16\" Mid Length Barrel, Stripped (BCM-BRL-s-MID-16-STD), Description","url":"https://bravocompanyusa.com/bcm-standard-16-mid-length-barrel-stripped/","retrieved":"2026-10-05","via":"harvest"}},{"id":"primary-arms","value":0.75,"unit":"in","pm":0.0005,"stated":".750\" gas seat diameter","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Bravo Company Manufacturing Chrome Lined 5.56 AR-15 Barrel - Mid-Length - Government - 16\" (BCM-BRL-S-MID-16-STD), Features","url":"https://www.primaryarms.com/bravo-company-manufacturing-standard-16-mid-length-barrel-stripped-bcm-brl-s-mid-16-std","retrieved":"2026-10-05","via":"harvest"}}],"adopt":{"from":"bcm","reason":"The maker's own; the seller repeats it."}},"extension_behind_breech":{"label":"The barrel extension's rear end behind the barrel's breech end","kind":"length","measurements":[{"id":"model","value":0.501,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{std.ar15.barrel_extension_behind_breech}","via":"user"},"note":"The reference CAD set's extension, 1.121 from its front face to its rear end, less the Army's .620 tenon: both readings and their sources are in the standard's ledger (std.ar15.barrel_extension_length, std.ar15.barrel_tenon_length) since 2026-10-05; until then the reading was kept here."}],"note":"The extension's length less the barrel's tenon, which screws into it from its front face (8448549 sheet 1: .620 ± .001). The extension's own drawing (8448550) isn't in the package, so its length is the reference CAD set's. The Aero barrel's ledger scaled it off 8448548's 1/1 view at 0.46 ± 0.04: the two agree within that. Since 2026-10-05 this is the one figure the catalog's three 5.56 barrels take their breech from (the standard's, `std.ar15.barrel_extension_behind_breech`, which the Aero barrel's ledger and Bear Creek's read too): they had 0.46, 0.501 and 0.57, and their muzzles stood 0.11 in apart. A check of the CAD set's extension against the Army's own figures: its locking lugs' front faces are 0.907 behind its front face (extension_lug_depth: 1.121 less 0.214), where the barrel's .620 tenon and the assembly drawing's .283 +.006 from the locking face to the breech face (8448548, Section A-A) make .903 to .909."},"overall_length":{"label":"End to end, the extension's rear to the muzzle","kind":"length","measurements":[{"id":"photo","value":16.91,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/bcm-16-mid-barrel 99b8653ffc94 (Primary Arms' gallery, BCM-BRL-S-MID-16-STD_01: the barrel from the side on white, the muzzle at the right, 4848 x 3232)","scaleRef":"its gas block journal's diameter, 202.55 px (columns 2910 to 3370, the silhouette at grey 200), as the published .750 (journal_od): 270.07 px/in","method":"its two end faces, each behind its rim's arc: the rear end's at column 149.1 (the rim an ellipse 30 px deep by 134 high: the lens sees that end from 12.7° off square), the muzzle's at 4717 (the tip at 4738, a 20 px arc): 4567.9 px","via":"harvest"}},{"id":"published","value":16.501,"unit":"in","pm":0.07,"source":{"type":"derived","expr":"{.length} + {.extension_behind_breech}","via":"harvest"}}],"adopt":{"from":"published","reason":"Lengths at the published length's scale: the journal's (a black tube's width on white) reads 2.5% short, and at the published one the gas port lands where the Aero barrel's and a mid-length chart's are, and the muzzle shoulder where BCM's photo of the complete upper has it."},"note":"The photo, at its journal's scale, reads 2.5% longer than the published length gives: a black tube reads thin on white (CLAUDE.md; the Aero barrel's photo did the same by 2.8% with its edge read at mid-grey, and reads within 0.3% at 235), so the diameter's scale is short and lengths read long by it. The published length is the scale for lengths, the journal the scale for diameters. Checks at the published scale: the gas port lands 9.13 ahead of the receiver's face (the Aero barrel's 9.17 and Bear Creek's 9.14 by their own photos; a mid-length chart's 9.18), and BCM's photo of its complete upper with this barrel has the muzzle device beginning 0.455 in ahead of the 15 in handguard's front end (shoulder_x's second measurement): 15.03, as here, not the 15.4 the journal's scale would make it. The ± covers whether the 16 is from the barrel's breech end (the Army's drawing) or from the bolt's face, an eighth further back."},"extension_rear_x":{"label":"The barrel extension's rear end, from the flange's rear face (negative: inside the receiver)","kind":"length","measurements":[{"id":"photo","value":-0.984,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-16-mid-barrel 99b8653ffc94 (Primary Arms' gallery, BCM-BRL-S-MID-16-STD_01: the barrel from the side on white, the muzzle at the right, 4848 x 3232)","scaleRef":"its end faces, 4567.9 px apart (columns 149.1 and 4717, each behind its rim's arc), as overall_length (16.501): 276.83 px/in","method":"the rear end's face (column 149.1) to the flange's rear face (column 421.6: where the flange's lower edge reaches its full depth; before it the edge is the rim's arc, an ellipse 32.9 px deep fitted over columns 406 to 420)","via":"harvest"}}],"note":"The reference CAD set's extension has 0.990 here (1.121 less its 0.131 flange)."},"flange_front_x":{"label":"The extension flange's front face, ahead of its rear face (the flange's thickness)","kind":"length","measurements":[{"id":"photo","value":0.095,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bcm-16-mid-barrel 99b8653ffc94 (Primary Arms' gallery, BCM-BRL-S-MID-16-STD_01: the barrel from the side on white, the muzzle at the right, 4848 x 3232)","scaleRef":"its end faces, 4567.9 px apart (columns 149.1 and 4717, each behind its rim's arc), as overall_length (16.501): 276.83 px/in","method":"the flange's rear face (column 421.6) to where its upper edge stops being level (column 448)","via":"harvest"}}],"note":"The reference CAD set's flange is 0.131 thick; this one reads thinner. Ahead of the face the silhouette's corner is the rim's far arc, seen past the barrel (to column 466)."},"flange_od":{"label":"The barrel extension's flange, its diameter as the side photo has it at the journal's scale","kind":"length","measurements":[{"id":"photo","value":1.185,"unit":"in","pm":0.007,"source":{"type":"photo","photo":"references/bcm-16-mid-barrel 99b8653ffc94 (Primary Arms' gallery, BCM-BRL-S-MID-16-STD_01: the barrel from the side on white, the muzzle at the right, 4848 x 3232)","scaleRef":"its gas block journal's diameter as the published .750 (tools/turned.py at grey 200: ratio 1.5804)","method":"the silhouette's widest, columns 424 to 444: 160.03 px of radius against the journal's 101.26","via":"harvest"}}],"note":"The scale reference of the traced outline (the silhouette's greatest height). The photo's breech end stands a little nearer the lens than its journal (extension_od: 1.2% large there), so the flange itself is nearer 1.171; the reference CAD set's is 1.170."},"extension_od":{"label":"The barrel extension's body, its diameter (what goes into the receiver)","kind":"length","measurements":[{"id":"tdp","value":0.999,"unit":"in","pm":0.001,"stated":"DIAMETER NOT TO EXCEED .9990 FOR THIS LENGTH AFTER ASSEMBLY AND BEFORE FINISH","source":{"type":"standard","doc":"US Army TDP drawing 8448548 (Barrel and Barrel Extension Assembly), rev N: the assembly's side view at 1/1; user-supplied scan, PDF page 212","via":"user"},"note":"An upper limit: it goes into the receiver's 1.000 bore (8448524). The reference CAD set's extension is .9987."},{"id":"photo","value":1.011,"unit":"in","pm":0.007,"source":{"type":"photo","photo":"references/bcm-16-mid-barrel 99b8653ffc94 (Primary Arms' gallery, BCM-BRL-S-MID-16-STD_01: the barrel from the side on white, the muzzle at the right, 4848 x 3232)","scaleRef":"its gas block journal's diameter as the published .750 (tools/turned.py at grey 200: ratio 1.3482)","method":"the extension's body, columns 170 to 335: 136.52 px of radius against the journal's 101.26","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's limit: an extension over 1.000 doesn't go into a receiver. The photo reads 1.2% large here because its breech end is nearer the lens than its journal."},"note":"The photo's reading says how square the photo is, not how big the extension is: the breech end is nearer the lens than the journal by about 1.2% (the arcs its seams make put the lens about 31 in off, opposite a point 7 in ahead of the receiver's face). The outline is not corrected for it: diameters behind the journal read up to 1.2% large, ahead of it up to 0.7% small."},"gas_port_x":{"label":"The gas port ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":9.13,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/bcm-16-mid-barrel 99b8653ffc94 (Primary Arms' gallery, BCM-BRL-S-MID-16-STD_01: the barrel from the side on white, the muzzle at the right, 4848 x 3232)","scaleRef":"its end faces, 4567.9 px apart (columns 149.1 and 4717, each behind its rim's arc), as overall_length (16.501): 276.83 px/in","method":"the flange's rear face (column 421.6) to the middle of the port's mouth on the upper edge and of the dimple's dent on the lower (column 2949)","via":"harvest"}}],"note":"BCM says \"gas ports installed and dimpled\" and gives no distance. The port is on top in the photo, in line with the marking (as 8448548's note 8 has markings): its mouth breaks the upper edge at columns 2935 to 2965, and the dimple opposite it dents the lower edge over 2926 to 2972. That is 0.28 ahead of the journal's rear shoulder (8448548 has .295 on the rifle's barrel; a mid-length chart .300). Checks: the Aero barrel's port is at 9.17 and Bear Creek's at 9.14; the chart in the TDP's folder (AR-15_M4_Barrel_Dimensions.jpg, a third-party illustration) puts a mid-length port 9.050 ahead of the extension's front face, 9.18 from this one with the reference CAD's 0.131 flange."},"journal_rear_x":{"label":"The gas block journal's rear shoulder (the collar's front face) ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":8.848,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-16-mid-barrel 99b8653ffc94 (Primary Arms' gallery, BCM-BRL-S-MID-16-STD_01: the barrel from the side on white, the muzzle at the right, 4848 x 3232)","scaleRef":"its end faces, 4567.9 px apart (columns 149.1 and 4717, each behind its rim's arc), as overall_length (16.501): 276.83 px/in","method":"the flange's rear face (column 421.6) to where the collar's edge ends (column 2871: the ends of the arc its front face's groove makes)","via":"harvest"}}],"note":"A gas block's rear face comes back to this shoulder. The Aero barrel's is at 8.87 and Bear Creek's at 8.85."},"journal_front_x":{"label":"The gas block journal's front end (where the barrel steps down) ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":10.716,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-16-mid-barrel 99b8653ffc94 (Primary Arms' gallery, BCM-BRL-S-MID-16-STD_01: the barrel from the side on white, the muzzle at the right, 4848 x 3232)","scaleRef":"its end faces, 4567.9 px apart (columns 149.1 and 4717, each behind its rim's arc), as overall_length (16.501): 276.83 px/in","method":"the flange's rear face (column 421.6) to the step ahead of the journal (column 3388: the ends of the arc the step makes)","via":"harvest"}}],"note":"The journal is 1.87 long: long enough for a front sight base's two bands."},"shoulder_x":{"label":"The muzzle shoulder ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":15.014,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-16-mid-barrel 99b8653ffc94 (Primary Arms' gallery, BCM-BRL-S-MID-16-STD_01: the barrel from the side on white, the muzzle at the right, 4848 x 3232)","scaleRef":"its end faces, 4567.9 px apart (columns 149.1 and 4717, each behind its rim's arc), as overall_length (16.501): 276.83 px/in","method":"the flange's rear face (column 421.6) to the shoulder's face where it meets the thread, on the silhouette's edges (column 4578; the arc the thread's root makes against the face ends at 4575.3)","via":"harvest"}},{"id":"upper-photo","value":15.03,"unit":"in","pm":0.07,"source":{"type":"photo","photo":"references/bcm-urg-mid-16-mcmr-15 a0e4baef2a6d (BCM's gallery: its complete upper with this barrel under the 15 in MCMR handguard, from the right, an A2 flash hider on the muzzle, 1500 x 1000)","scaleRef":"its top rail's teeth, 21.215 px apart along the handguard (std.picatinny.slot_pitch): 53.85 px/in","method":"the bare barrel between the handguard's foremost point (column 1316) and where the muzzle device and its washer begin (column 1341): 0.455 in, ahead of the handguard's front end as that part's ledger has it on 2026-10-05 (bcm-mcmr-15-handguard.rear_x -0.4225 + length 15: 14.578)","via":"harvest"},"note":"Another photo, another scale, another part's figures: the ± is two pixels and the handguard's own."}],"adopt":{"from":"photo","reason":"The barrel's own photo, at five times the resolution; BCM's photo of the complete upper puts the shoulder within 0.02 of it."},"note":"Where the thread begins: a muzzle device or its washer seats here. The corner behind it is rounded in the outline, partly by the rim's arc (the lens sees the muzzle end from 16° off square)."},"thread_length":{"label":"The muzzle thread's length","kind":"length","measurements":[{"id":"photo","value":0.502,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-16-mid-barrel 99b8653ffc94 (Primary Arms' gallery, BCM-BRL-S-MID-16-STD_01: the barrel from the side on white, the muzzle at the right, 4848 x 3232)","scaleRef":"its end faces, 4567.9 px apart (columns 149.1 and 4717, each behind its rim's arc), as overall_length (16.501): 276.83 px/in","method":"the shoulder's face (column 4578) to the muzzle's face (column 4717, behind its rim's 20 px arc)","via":"harvest"}}],"note":"Shorter than the Army's .63 (8448549 sheet 1, from the shoulder to the muzzle; a mid-length chart has .624), by this photo. The thread's own pitch reads 9.204 px, 257.7 px/in at 28 to the inch, where this scale would have 9.8 px: by the thread as the ruler the muzzle end reads 6% short and the thread is 0.54. Not explained (see the part's gaps), and the ± says so."},"muzzle_od":{"label":"The diameter behind the muzzle thread","kind":"length","measurements":[{"id":"photo","value":0.687,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/bcm-16-mid-barrel 99b8653ffc94 (Primary Arms' gallery, BCM-BRL-S-MID-16-STD_01: the barrel from the side on white, the muzzle at the right, 4848 x 3232)","scaleRef":"its gas block journal's diameter as the published .750 (tools/turned.py at grey 200: ratio 0.9161)","method":"the section behind the shoulder, columns 4440 to 4555: 92.77 px of radius against the journal's 101.26","via":"harvest"}}],"note":"The last section before the shoulder (0.59 long). The section behind it, from the journal's front end, is 0.716, narrowing to 0.709."},"gas_port_d":{"label":"The gas port's diameter","kind":"length","measurements":[{"id":"chart","value":0.075,"unit":"in","pm":0.01,"stated":"0.075\"ø Gas Port","source":{"type":"spec","publisher":"unknown","name":"AR-15_M4_Barrel_Dimensions.jpg in the user's TDP folder (Spec_Sheets): a third-party illustration of a 14.5 in mid-length barrel, no drawing number"}}],"note":"BCM publishes none. A mid-length chart's figure, for the hole the model cuts; the rifle's (8448548) is .092."},"bore_d":{"label":"The bore's diameter (across the lands)","kind":"length","measurements":[{"id":"tdp","value":0.219,"unit":"in","pm":0.001,"stated":".219 DIA+.001","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 2 of 2, rev J: Section U-U, rifling detail at 10/1; user-supplied scan, PDF page 211","via":"user"}}]},"index_pin_d":{"label":"The barrel indexing pin's diameter","kind":"length","measurements":[{"id":"model","value":0.125,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Indexing_Pin.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"its one cylinder, radius .0625, .185 long (.cache/batch123/bcm-16-mid-barrel/stepread.py)","via":"user"}}],"note":"The pin's own drawing (8448551, PDF page 119) wasn't read. In the photo the pin shows 31 px of its width (0.11) before the flange's corner hides its front."},"index_pin_x":{"label":"The barrel indexing pin's axis behind the flange's rear face","kind":"length","measurements":[{"id":"photo","value":0.113,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bcm-16-mid-barrel 99b8653ffc94 (Primary Arms' gallery, BCM-BRL-S-MID-16-STD_01: the barrel from the side on white, the muzzle at the right, 4848 x 3232)","scaleRef":"its end faces, 4567.9 px apart (columns 149.1 and 4717, each behind its rim's arc), as overall_length (16.501): 276.83 px/in","method":"the pin's rear edge on the upper silhouette (column 373) plus half index_pin_d, to the flange's rear face (column 421.6)","via":"harvest"}}],"note":"0.208 behind the flange's front face, as the reference CAD set has it (0.2075)."},"index_pin_top":{"label":"The barrel indexing pin's top above the bore's axis","kind":"length","measurements":[{"id":"photo","value":0.584,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-16-mid-barrel 99b8653ffc94 (Primary Arms' gallery, BCM-BRL-S-MID-16-STD_01: the barrel from the side on white, the muzzle at the right, 4848 x 3232)","scaleRef":"its gas block journal's diameter as the published .750 (tools/turned.py at grey 200: ratio 1.5579)","method":"the pin's top on the upper silhouette, columns 376 to 401: 157.75 px above the axis against the journal's 101.26 of radius","via":"harvest"}}],"note":"A little under the flange's radius: the pin stands 0.08 out of the extension."},"extension_mouth_d":{"label":"The barrel extension's rear opening, its diameter at the rear face","kind":"length","measurements":[{"id":"model","value":0.77,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Extension.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"the rear face is the plane at 1.121 between radii .3850 and .4893 (.cache/batch123/bcm-16-mid-barrel/stepread.py: its faces along its axis, from its front face at 0 to its rear end at 1.121)","via":"user"}}],"note":"The inside of a mil-spec extension as the reference CAD set has it, for how the rear end looks (BCM: an M4 feed ramp extension, USGI; Primary Arms' photo _04 shows its lugs). Appearance only."},"extension_mouth_chamfer":{"label":"The rear opening's chamfer, its depth (at 45°, also how far it narrows the opening's radius)","kind":"length","measurements":[{"id":"model","value":0.045,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Extension.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"the cone at 45° from 1.076 to 1.121 (.cache/batch123/bcm-16-mid-barrel/stepread.py: its faces along its axis, from its front face at 0 to its rear end at 1.121)","via":"user"}}]},"extension_lug_bore_d":{"label":"The circle the extension's locking lugs leave between their tips","kind":"length","measurements":[{"id":"model","value":0.572,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Extension.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"eight cylinder faces of radius .2860, 0.922 to 1.022 (.cache/batch123/bcm-16-mid-barrel/stepread.py: its faces along its axis, from its front face at 0 to its rear end at 1.121)","via":"user"}}]},"extension_lug_depth":{"label":"The locking lugs' front faces, ahead of the extension's rear end","kind":"length","measurements":[{"id":"model","value":0.214,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Extension.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"the plane across the axis at 0.907 (radii .3010 to .4150): 1.121 less 0.907 (.cache/batch123/bcm-16-mid-barrel/stepread.py: its faces along its axis, from its front face at 0 to its rear end at 1.121)","via":"user"}}]},"extension_recess_d":{"label":"The recess ahead of the lugs, which the bolt's lugs turn in: its diameter","kind":"length","measurements":[{"id":"model","value":0.83,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Extension.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"the cylinder of radius .4150, 0.5262 to 0.9070 (.cache/batch123/bcm-16-mid-barrel/stepread.py: its faces along its axis, from its front face at 0 to its rear end at 1.121)","via":"user"}}]},"extension_recess_depth":{"label":"The recess's front end, ahead of the extension's rear end","kind":"length","measurements":[{"id":"model","value":0.595,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Extension.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"the cylinder of radius .4150 begins at 0.5262: 1.121 less 0.5262 (.cache/batch123/bcm-16-mid-barrel/stepread.py: its faces along its axis, from its front face at 0 to its rear end at 1.121)","via":"user"}}]},"thread_major_d":{"label":"The muzzle thread's major diameter (its crests)","kind":"length","measurements":[{"id":"tdp","value":0.4957,"unit":"in","pm":0.0033,"stated":"1/2-28 UNEF-2A MAJOR DIA .4989/.4924","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213","via":"user"}}],"note":"The Army barrel's 1/2-28 thread, for the 1/2 X 28 the seller states: what the model's thread is drawn at. The photo's silhouette of the thread is 0.479 at the journal's scale, between its crests and its roots."},"thread_minor_d":{"label":"The muzzle thread's minor diameter (its roots)","kind":"length","measurements":[{"id":"tdp","value":0.4551,"unit":"in","pm":0.002,"stated":"MINOR DIA .4551 MAX","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213","via":"user"}}]},"thread_pitch":{"label":"The muzzle thread's pitch","kind":"length","measurements":[{"id":"tdp","value":0.03571,"unit":"in","pm":0.00005,"stated":"1/2-28 UNEF-2A","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213","via":"user"}},{"id":"primary-arms","value":0.03571,"unit":"in","pm":0.00005,"stated":"Thread Pattern 1/2 X 28","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Bravo Company Manufacturing Chrome Lined 5.56 AR-15 Barrel - Mid-Length - Government - 16\" (BCM-BRL-S-MID-16-STD), Specifications","url":"https://www.primaryarms.com/bravo-company-manufacturing-standard-16-mid-length-barrel-stripped-bcm-brl-s-mid-16-std","retrieved":"2026-10-05","via":"harvest"}}],"adopt":{"from":"primary-arms","reason":"The seller's statement for this barrel; the Army's drawing has the same thread on its own."},"note":"28 threads to the inch, by the seller's statement and the Army barrel's drawing: neither is a measurement of this barrel. The photo's own stripes are 9.204 px apart, which is 28 to the inch only at 257.7 px/in; the published length's scale is 276.8 there (see thread_length and the part's gaps)."},"outline_rear_face":{"label":"The extension's rear face in the traced outline's own frame (from the silhouette's rear tip, at the journal's scale)","kind":"length","measurements":[{"id":"photo","value":0.112,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/bcm-16-mid-barrel 99b8653ffc94 (Primary Arms' gallery, BCM-BRL-S-MID-16-STD_01: the barrel from the side on white, 4848 x 3232)","scaleRef":"scale from bcm-16-mid-barrel.flange_od = 1.185 in (y-extent 320 px → 270.2 px/in)","method":"the min end's face: the silhouette's tip at 0.000 less its rim's arc, 0.111 in of sag at radius 0.503871 (the end is seen from 12.5° off square; arc fitted over 121 rows, rms 0.001) of the traced outline (tools/trace.py); the extension's rear face in the outline's own frame (from its rear tip, at the journal's scale)","via":"harvest"}}],"note":"Where the outline is cut: the silhouette's tip is the rear rim's near side, which stands behind the face by the rim's arc."},"outline_front_face":{"label":"The muzzle's face in the traced outline's own frame (from the silhouette's rear tip, at the journal's scale)","kind":"length","measurements":[{"id":"photo","value":17.005,"unit":"in","pm":0.101,"source":{"type":"photo","photo":"references/bcm-16-mid-barrel 99b8653ffc94 (Primary Arms' gallery, BCM-BRL-S-MID-16-STD_01: the barrel from the side on white, 4848 x 3232)","scaleRef":"scale from bcm-16-mid-barrel.flange_od = 1.185 in (y-extent 320 px → 270.2 px/in)","method":"the max end's face: the silhouette's tip at 17.101 less its rim's arc, 0.097 in of sag at radius 0.238269 (the end is seen from 22.1° off square; arc fitted over 121 rows, rms 0.001) of the traced outline (tools/trace.py); the muzzle's face in the outline's own frame (from its rear tip, at the journal's scale)","via":"harvest"}}],"note":"Where the outline is cut: the silhouette's front tip is the muzzle rim's near side."}}},{"subject":"bcm-625-gas-block","title":"BCM® Low Profile Gas Block (steel with set screws) 625 (BCM-LGB-625)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"metal","value":1.93,"unit":"oz","pm":0.12,"source":{"type":"derived","expr":"(0.785398163 * ({.section_equivalent_d} * {.section_equivalent_d} - {.journal_id} * {.journal_id}) * {.length} - 0.785398163 * {.tube_hole_d} * {.tube_hole_d} * ({.length} - {.pin_hole_from_front} + {.tube_hole_past_pin})) * {std.density.steel}","via":"harvest"}},{"id":"midwayusa-shipping","value":0.183,"unit":"lb","pm":0.0005,"stated":"shippingWeightDisplay\":\"0.183 Pounds","source":{"type":"spec","publisher":"retailer","name":"MidwayUSA, Bravo Company BCM Low Profile Gas Block AR-15, LR-308 .625\" (product 594888, manufacturer number BCM-LGB-625), delivery information","url":"https://www.midwayusa.com/product/1025636846?pid=594888","retrieved":"2026-10-12","via":"harvest"},"note":"A shipping weight: the block in its packet (2.93 oz, half as much again as its steel). The .750 block's on the same page is 0.171 lb, lighter where it has less steel bored out: the difference between the two, 0.19 oz, is a little under what the two bores make (0.61 oz by these figures), so the packets aren't weighed to the part."}],"adopt":{"from":"metal","reason":"No page states the block's own weight; the seller's figure is the parcel's. Its steel by its own sizes is taken, and said to be worked out."},"note":"WORKED OUT, not published: BCM states no weight for it, nor does any seller's page read. Its own steel: its section's area (section_equivalent_d) less the bore, along its length, less the gas tube's hole, times std.density.steel. The roll pin's cross hole, the gas port and the two set screws' holes aren't taken off, nor the two set screws added (each about fills its hole). The ± covers the section's area (3%, the outline's ± 0.012 in round it) and the density's range. MidwayUSA's figure is what the parcel weighs."},"journal_id":{"label":"Bore (the journal it fits: .750 or .625)","kind":"length","measurements":[{"id":"bcm","value":0.625,"unit":"in","pm":0.001,"stated":"Machined of steel, phosphate finish, for .625 barrels.","source":{"type":"spec","publisher":"manufacturer","name":"Bravo Company USA, BCM® Low Profile Gas Block (steel with set screws) 625 (BCM-LGB-625), Description","url":"https://bravocompanyusa.com/bcm-low-profile-gas-block-steel-with-set-screws-625/","retrieved":"2026-10-12","via":"harvest"}},{"id":"primary-arms","value":0.625,"unit":"in","pm":0.001,"stated":"Gas Seat Diameter .625","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Bravo Company Manufacturing Low Profile AR-15 Gas Block - Set Screw - .625\" (BCM-LGB-625), Specifications; its Features: \".625\" gas seat diameter\"; its Details: \"This version is sized for a .625\" gas block journal.\"","url":"https://www.primaryarms.com/bravo-company-mfg-low-profile-gas-block-625-set-screw-style-bcm-lgb-625","retrieved":"2026-10-12","via":"harvest"}}],"adopt":{"from":"bcm","reason":"The maker's sentence; the seller's table says the same."},"note":"BCM: \"Barrel ID honed after finish per USGI TDP.\" The .750 block is another product (BCM-LGB-750)."},"height":{"label":"Height, the tube's boss's top to the set screws' flat","kind":"length","measurements":[{"id":"ar15-build","value":1.34,"unit":"in","pm":0.005,"stated":"Dimensions: 1.34\" high, 1\" long","source":{"type":"spec","publisher":"unknown","name":"AR15.BUILD (a parts database, not a seller), Bravo Company AR-15/M16 .625 inch Low-Profile Gas Block (MPN BCM-LGB-625), SPECS","url":"https://ar15.build/products/gas-block/116629/bravo-company-ar-15-m16-625-inch-low-p-bcm-lgb-625","retrieved":"2026-10-12","via":"harvest"},"note":"No source is named for the figure, and what the height spans isn't said."},{"id":"photo-mouth","value":1.33,"unit":"in","pm":0.035,"source":{"type":"photo","photo":"references/bcm-625-gas-block 453104958d81 (Primary Arms BCM-LGB-625_00.jpg: an oblique view of the star face, 2200 x 1466)","scaleRef":"the bore's mouth along the face's axis, 345.1 px, as journal_id (.625): 552.2 px/in","method":"by the bore's mouth alone: the mouth is a circle in the face's plane, so along any line in that plane a length is its length in the photo over the mouth's chord along the same line, times .625. On the face's axis (the mouth's centre to the boss's top) the boss's top is 431.9 px above the centre and the flat 301.6 below it where the mouth's chord is 345.1 px: 0.783 and 0.547 in. The ± covers the picked top (± 4 px), the mouth's rim (found on 48 rays, a conic fitted, rms 2.3 px: its edge break is in it) and the perspective left in","via":"harvest"}},{"id":"sibling","value":1.34,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-750-gas-block.height}","via":"harvest"},"note":"The .750 block's height, two sellers' figure for that number (data/ledger/bcm-750-gas-block.yaml). Not carried over on its name: this block's own photos show the same outside (the note above)."}],"adopt":{"from":"ar15-build","reason":"The one page that states it for this number; the block's own photo by its bore reads it within its ±, and the .750 block of the same outside has it from two sellers."},"note":"BCM gives none. One page states it for this number, a parts database that names no source; the block's own photo, scaled by its own bore's mouth as the .625 it is honed to, reads it within a hundredth; and it is the .750 block's height (two sellers'), whose outside this block has: by its own photos the boss's top is as far above the bore and the flat as far below it as the .750's within 0.01 in, the flat as wide (0.295 against 0.297), the star at the same height and size, the block as long and its roll pin's hole in the same place."},"length":{"label":"Length along the barrel","kind":"length","measurements":[{"id":"ar15-build","value":1,"unit":"in","pm":0.5,"stated":"Dimensions: 1.34\" high, 1\" long","source":{"type":"spec","publisher":"unknown","name":"AR15.BUILD (a parts database, not a seller), Bravo Company AR-15/M16 .625 inch Low-Profile Gas Block (MPN BCM-LGB-625), SPECS","url":"https://ar15.build/products/gas-block/116629/bravo-company-ar-15-m16-625-inch-low-p-bcm-lgb-625","retrieved":"2026-10-12","via":"harvest"},"note":"A whole inch beside a height to the hundredth: its ± is half its last digit."},{"id":"photo","value":1.011,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/bcm-625-gas-block 4f19e3379457 (Primary Arms BCM-LGB-625_03.jpg: the block's right side straight on, the star face at the right, 2200 x 1467)","scaleRef":"its height on the line across its middle, 964.4 px (the top edge at row 242.3 and the bottom at 1206.7 at column 1000, the silhouette at grey 235), as height (1.34): 719.7 px/in","method":"the block's width in the boss's rows, clear of the ring's (the front edge bulges there by the end face's rim, 8 px): 729.3 px over rows 270 to 480, 1.013 in; the other side's photo (ac5f36084b6e, BCM-LGB-625_02: 766.9 px where its height is 1019.7) gives 1.008, and this is their mean. The ± covers the scale (the height's), the edges and the lens's distance (the boss's sides stand 0.14 in nearer than the top and bottom edges)","via":"harvest"}}],"adopt":{"from":"photo","reason":"The database's figure is a whole inch; the side photo at the height's scale gives the hundredths, and agrees with it."},"note":"BCM gives none. A database's figure is to the inch; the side photo, at the height's scale, gives the hundredths. Faxon, of the journal this block is for: \"use a block 1″ long or shorter\" on its 1.1 in journal. The .750 block reads 1.008 the same way."},"height_above_bore":{"label":"Top above the bore axis","kind":"length","measurements":[{"id":"photo","value":0.789,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-625-gas-block 694b5d90ca1f (Primary Arms BCM-LGB-625_00.jpg, 453104958d81, an oblique view of the star face, turned square by the block's own bore: the mouth round, the face's axis upright: derived-694b5d90ca1f.manifest.json, 1200 x 1600)","scaleRef":"the face's height on its own axis, 1072 px (the boss's top at row 288.6 to the tab's flat at 1360.6), as height (1.34): 800 px/in","method":"the boss's top above the mouth's centre: 431.9 px of the 733.5 between the boss's top and the flat on the face's axis in the photo (row 288.6 above row 920 in the turned picture). The ± covers the picked top (± 4 px), where the bore's centre is taken to be (the mouth's, as a conic fitted to its rim) and the perspective left in","via":"harvest"}}],"note":"Not published. The boss's top above the bore's centre on the star face turned square by the bore's own mouth, at the height's scale. By the bore alone (.625) it reads 0.783; the .750 block's is 0.785."},"tab_below_bore":{"label":"The set screws' flat below the bore axis","kind":"length","measurements":[{"id":"photo","value":0.551,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-625-gas-block 694b5d90ca1f (Primary Arms BCM-LGB-625_00.jpg, 453104958d81, an oblique view of the star face, turned square by the block's own bore: the mouth round, the face's axis upright: derived-694b5d90ca1f.manifest.json, 1200 x 1600)","scaleRef":"the face's height on its own axis, 1072 px (the boss's top at row 288.6 to the tab's flat at 1360.6), as height (1.34): 800 px/in","method":"the tab's flat below the mouth's centre where the face's axis meets it: 301.6 px of the 733.5 (row 1360.6 under row 920 in the turned picture). The flat is the silhouette's lower edge against the white ground; it lies 1.7° from square to the axis in the turned picture, which is the perspective left in","via":"harvest"}}],"note":"By the bore alone (.625) it reads 0.547; the .750 block's is 0.555."},"od":{"label":"Outside diameter of its ring about the barrel","kind":"length","measurements":[{"id":"photo","value":0.854,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/bcm-625-gas-block 694b5d90ca1f (Primary Arms BCM-LGB-625_00.jpg (453104958d81), the star face turned square by the block's own bore (the mouth round, the face's axis upright): derived-694b5d90ca1f.manifest.json, 1200 x 1600)","scaleRef":"frame from the reviewed holes top, flat (800.0 px/in, rms 0.000 in over 2 points)","method":"width in y [-0.2, 0.2] of the traced outline (tools/trace.py); across the ring at the bore's height; the ± covers the edge (the left side read against the white ground to a pixel or two, the right side its mirror: the face's own right edge reads 0.009 in further out at this height), the scale and the perspective left in the turned picture (its flat lies 1.7° off level)","via":"harvest"}}],"note":"Not published. Across the ring at the bore's height in the star face turned square by the bore. The .750 block's reads 0.88 ± 0.025 by its own photo: this one's ring is 0.03 narrower by its own, inside the two readings' ±, and whether the ring really is thinner on the .625 block isn't settled by them. The outline's left side is the face's edge against the white ground; its right side is that edge mirrored about the axis, and the face's own right edge, read at the bore's height where the block's side stands behind it, is 0.009 in further out."},"boss_width":{"label":"Width of the gas tube's boss on top","kind":"length","measurements":[{"id":"photo","value":0.264,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-625-gas-block 694b5d90ca1f (Primary Arms BCM-LGB-625_00.jpg (453104958d81), the star face turned square by the block's own bore (the mouth round, the face's axis upright): derived-694b5d90ca1f.manifest.json, 1200 x 1600)","scaleRef":"frame from the reviewed holes top, flat (800.0 px/in, rms 0.000 in over 2 points)","method":"median row width in y [0.52, 0.66] (0.251–0.299) of the traced outline (tools/trace.py); the boss's neck, its sides closest","via":"harvest"}}],"note":"Not published. Across the boss's neck, where its sides are closest, in the star face turned square. The .750 block's is 0.288."},"section_equivalent_d":{"label":"Its section's area, as the diameter of the disc that has it","kind":"length","measurements":[{"id":"photo","value":0.976,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bcm-625-gas-block 694b5d90ca1f (Primary Arms BCM-LGB-625_00.jpg, 453104958d81, an oblique view of the star face, turned square by the block's own bore: the mouth round, the face's axis upright: derived-694b5d90ca1f.manifest.json, 1200 x 1600)","scaleRef":"the face's height on its own axis, 1072 px (the boss's top at row 288.6 to the tab's flat at 1360.6), as height (1.34): 800 px/in","method":"the area inside the outline's 78 points in the turned picture, 478,400 px² (0.7475 in² at 800 px/in), as 2 √(area / π). The ± is the outline's ± 0.012 in round its 3.5 in","via":"harvest"}}],"note":"For the weight: the area inside its traced outline (profiles.front, the star face turned square by the bore, its right side the left's mirror) is 0.7475 square inches, the bore not taken out; a disc of that area is this far across. The .750 block's outline holds 0.7726 the same way."},"pin_hole_from_front":{"label":"The roll pin's cross hole behind the front (star) face","kind":"length","measurements":[{"id":"photo","value":0.317,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/bcm-625-gas-block 4f19e3379457 (Primary Arms BCM-LGB-625_03.jpg: the block's right side straight on, the star face at the right, 2200 x 1467)","scaleRef":"its height on the line across its middle, 964.4 px (the top edge at row 242.3 and the bottom at 1206.7 at column 1000, the silhouette at grey 235), as height (1.34): 719.7 px/in","method":"the hole's centre (column 1226.8: its rim's two sides on row 364, columns 1199.0 and 1254.5) to the front face's edge in the boss's rows (column 1454.7): 227.9 px","via":"harvest"}}],"note":"The star is on the face nearer the pin (the oblique photo), and the tube's pin is at the tube's front end: the star face is the muzzle end. The .750 block's is 0.315."},"pin_hole_d":{"label":"The roll pin's cross hole, diameter","kind":"length","measurements":[{"id":"tdp","value":0.078,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{bcm-750-gas-block.pin_hole_d}","via":"user"},"note":"The Army's front sight's hole for the gas tube's pin (8448566: \".078 DIA +.003 THRU\"), as read for the .750 block's ledger, where the drawing and its page are cited: the block takes the same tube and pin (BCM: \"for AR15, M16, M4, M4A1\")."},{"id":"photo","value":0.077,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/bcm-625-gas-block 4f19e3379457 (Primary Arms BCM-LGB-625_03.jpg: the block's right side straight on, the star face at the right, 2200 x 1467)","scaleRef":"its height on the line across its middle, 964.4 px (the top edge at row 242.3 and the bottom at 1206.7 at column 1000, the silhouette at grey 235), as height (1.34): 719.7 px/in","method":"the hole's rim along the block, row 364: columns 1199.0 to 1254.5, 55.5 px. Up the block it shows 49 px (rows 339.5 to 388.5): the lens looks a little down through it (the ground shows through its upper part only)","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The pin it takes is the Army's; the photo's hole is that size within its ±."}},"pin_to_port":{"label":"The gas tube's pin hole to its gas hole","kind":"length","measurements":[{"id":"tdp","value":0.418,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{bcm-750-gas-block.pin_to_port}","via":"user"},"note":"The Army's gas tube (8448567: \".418 ±.002\"), as read for the .750 block's ledger, where the drawing and its page are cited."}]},"port_from_rear":{"label":"Its gas port ahead of its rear face","kind":"length","measurements":[{"id":"derived","value":0.276,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{.length} - {.pin_hole_from_front} - {.pin_to_port}","via":"harvest"}}],"note":"Not published. Where the standard tube's gas hole lands when its pin is in the block's cross hole: the block's length less the pin's place behind the front face less the tube's pin-to-port. The Army's own sight has its port .270 from its rear face (8448566); the .750 block comes to 0.275."},"tube_hole_above_bore":{"label":"The gas tube's hole, its axis above the bore (at the block)","kind":"length","measurements":[{"id":"tdp","value":0.625,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{bcm-750-gas-block.tube_hole_above_bore}","via":"user"},"note":"The Army's front sight (8448566: \".625 ±.003\", the gas tube's hole above the barrel's hole), as read for the .750 block's ledger: the block takes the Army's tube."},{"id":"photo","value":0.618,"unit":"in","pm":0.035,"source":{"type":"photo","photo":"references/bcm-625-gas-block 4f19e3379457 (Primary Arms BCM-LGB-625_03.jpg: the block's right side straight on, the star face at the right, 2200 x 1467)","scaleRef":"its height on the line across its middle, 964.4 px (the top edge at row 242.3 and the bottom at 1206.7 at column 1000, the silhouette at grey 235), as height (1.34): 719.7 px/in","method":"the roll pin's hole (the pin crosses the tube's hole), its centre (row 364.0) 123.1 px below the top edge there (row 240.9): 0.171 in below the boss's top, which is height_above_bore (0.789 ± 0.03) above the bore","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The block takes the Army's tube; the pin's hole in the photo is at that height within the ±."}},"tube_hole_d":{"label":"The gas tube's hole, diameter","kind":"length","measurements":[{"id":"tdp","value":0.1805,"unit":"in","pm":0.001,"source":{"type":"derived","expr":"{bcm-750-gas-block.tube_hole_d}","via":"user"},"note":"8448566: \".1805 DIA +.0010\", as read for the .750 block's ledger."}],"note":"Not published, and no photo on file shows the rear face. The Army's sight's hole for the same .180 tube."},"tube_hole_past_pin":{"label":"How far the gas tube's hole runs on ahead of the pin's hole","kind":"length","measurements":[{"id":"tdp","value":0.217,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{bcm-750-gas-block.tube_hole_past_pin}","via":"user"},"note":"The Army's sight: the tube's hole .905 deep, the pin .688 from the same face (8448566), as read for the .750 block's ledger."}],"note":"Not published. The star face is closed (the oblique photo); the hole enters from the rear as on the .750 block (BCM's photo of that block's rear face)."},"star_center_above_bore":{"label":"The star on the front face, its centre above the bore axis","kind":"length","measurements":[{"id":"photo","value":0.553,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bcm-625-gas-block 694b5d90ca1f (Primary Arms BCM-LGB-625_00.jpg, 453104958d81, an oblique view of the star face, turned square by the block's own bore: the mouth round, the face's axis upright: derived-694b5d90ca1f.manifest.json, 1200 x 1600)","scaleRef":"the face's height on its own axis, 1072 px (the boss's top at row 288.6 to the tab's flat at 1360.6), as height (1.34): 800 px/in","method":"the mean of its five tips in the turned picture ((608, 386), (692, 450), (657, 553), (554, 551), (524, 448): the furthest bright pixel of the mark each way): row 477.6, 442.4 px above the mouth's centre (row 920). Their mean is 7 px to one side of the axis","via":"harvest"}}],"note":"BCM's star, laser-marked on the boss's front face (all three photos of that face show it). The .750 block's is 0.552 above its bore."},"star_radius":{"label":"The star on the front face, its centre to a tip","kind":"length","measurements":[{"id":"photo","value":0.1125,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/bcm-625-gas-block 694b5d90ca1f (Primary Arms BCM-LGB-625_00.jpg, 453104958d81, an oblique view of the star face, turned square by the block's own bore: the mouth round, the face's axis upright: derived-694b5d90ca1f.manifest.json, 1200 x 1600)","scaleRef":"the face's height on its own axis, 1072 px (the boss's top at row 288.6 to the tab's flat at 1360.6), as height (1.34): 800 px/in","method":"the five tips' mean distance from their own centre, 90.0 px (88.1 to 91.6)","via":"harvest"}}],"note":"The .750 block's is 0.115."}}},{"subject":"bcm-750-gas-block","title":"BCM® Low Profile Gas Block (steel with set screws) 750 (BCM-LGB-750)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"ar15discounts","value":2.08,"unit":"oz","pm":0.005,"stated":"Weight 2.08 oz","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, BCMGUNFIGHTER .750 Low Profile Gas Block (BCM-LGB-750), Additional information","url":"https://ar15discounts.com/products/bcmgunfighter-750-low-profile-gas-block/","retrieved":"2026-10-05","via":"harvest"}}],"note":"BCM and Primary Arms give none. One seller's figure, with its two set screws or without isn't said."},"journal_id":{"label":"Bore (the journal it fits: .750 or .625)","kind":"length","measurements":[{"id":"bcm","value":0.75,"unit":"in","pm":0.001,"stated":"Machined of steel, phosphate finish, for .750 barrels.","source":{"type":"spec","publisher":"manufacturer","name":"Bravo Company USA, BCM® Low Profile Gas Block (steel with set screws) 750 (BCM-LGB-750), Description","url":"https://bravocompanyusa.com/bcm-low-profile-gas-block-steel-with-set-screws-750/","retrieved":"2026-10-05","via":"harvest"}},{"id":"primary-arms","value":0.75,"unit":"in","pm":0.001,"stated":"Gas Seat Diameter .750","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Bravo Company Manufacturing Low Profile AR-15 Gas Block - Set Screw - .750\" (BCM-LGB-750), Specifications","url":"https://www.primaryarms.com/bravo-company-mfg-low-profile-gas-block-750-set-screw-style-bcm-lgb-750","retrieved":"2026-10-05","via":"harvest"}}],"adopt":{"from":"bcm","reason":"The maker's sentence; the seller's table says the same."},"note":"BCM: \"Barrel ID honed after finish per USGI TDP.\" The .625 block is another product (BCM-LGB-625)."},"height":{"label":"Height, the tube's boss's top to the set screws' flat","kind":"length","measurements":[{"id":"alexanders","value":1.34,"unit":"in","pm":0.005,"stated":"Height: 1.34 inches","source":{"type":"spec","publisher":"retailer","name":"Alexander's, BCM Low-Profile Gas Block .750 – Steel, Black Phosphate (BCM-LGB-750), Key Specifications","url":"https://alexandersstore.com/product/bcm-low-profile-gas-block-750-bbl/","retrieved":"2026-10-05","via":"harvest"}},{"id":"ar15discounts","value":1.34,"unit":"in","pm":0.005,"stated":"Dimensions 1 × 1.34 × 1.34 in","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, BCMGUNFIGHTER .750 Low Profile Gas Block (BCM-LGB-750), Additional information","url":"https://ar15discounts.com/products/bcmgunfighter-750-low-profile-gas-block/","retrieved":"2026-10-05","via":"harvest"}},{"id":"photo-mouth","value":1.306,"unit":"in","pm":0.035,"source":{"type":"photo","photo":"references/bcm-750-gas-block 04a45a69497d (Primary Arms BCM-LGB-750_00.jpg, 3ce1f7e276b9, an oblique view of the star face, turned square: its axis upright, its flat level, the bore's mouth as wide as tall: derived-04a45a69497d.manifest.json)","scaleRef":"the bore's mouth along the face's axis, 612.6 px (484.9 px in the photo, by the ellipse fitted to its rim), as journal_id (.750): 816.8 px/in","method":"the boss's top (row 295.5) to the tab's flat (row 1361.8): 1066.3 px. The ± covers the picked edges (±5 px), the perspective left in (about 3% across the face) and the mouth's edge break","via":"harvest"}}],"adopt":{"from":"alexanders","reason":"Two sellers' pages state it; the photo by the bore's mouth is within its ± and reads small the way an edge break at the mouth would make it."},"note":"BCM gives none. Two sellers state 1.34 (AR15Discounts as two of three figures, so its table isn't the part's width). By the bore's mouth as the .750 it is honed to, the star face reads 2.5% less: the mouth's edge in the photo is the outside of the bore's edge break, so that scale reads small."},"length":{"label":"Length along the barrel","kind":"length","measurements":[{"id":"alexanders","value":1,"unit":"in","pm":0.5,"stated":"Length: 1 inch","source":{"type":"spec","publisher":"retailer","name":"Alexander's, BCM Low-Profile Gas Block .750 – Steel, Black Phosphate (BCM-LGB-750), Key Specifications","url":"https://alexandersstore.com/product/bcm-low-profile-gas-block-750-bbl/","retrieved":"2026-10-05","via":"harvest"},"note":"A whole inch beside a height to the hundredth: its ± is half its last digit. The same page's \"Additional information\" has \"Length 6.9500\", which is not the block's."},{"id":"ar15discounts","value":1,"unit":"in","pm":0.5,"stated":"Dimensions 1 × 1.34 × 1.34 in","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, BCMGUNFIGHTER .750 Low Profile Gas Block (BCM-LGB-750), Additional information","url":"https://ar15discounts.com/products/bcmgunfighter-750-low-profile-gas-block/","retrieved":"2026-10-05","via":"harvest"}},{"id":"photo","value":1.008,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/bcm-750-gas-block 8c329d289596 (AR15Discounts BCM-LGB-750_01.jpg: the block's right side straight on, the star face at the right, 2200 x 1467)","scaleRef":"scale from bcm-750-gas-block.height = 1.34 in (y-extent 990 px → 738.8 px/in)","method":"median row width in y [-0.33, -0.06] (1.006–1.008) of the traced outline (tools/trace.py); the boss's rows, clear of the ring's (the right edge bulges there by the end face's rim, 8 px); the ± covers the scale (the height's), the edges and the lens's distance (the boss's sides stand 0.14 in nearer than the top and bottom edges)","via":"harvest"}}],"adopt":{"from":"photo","reason":"The sellers' figure is a whole inch; the side photo at the height's scale gives the hundredths, and agrees with it."},"note":"BCM gives none. The sellers' figure is to the inch; the side photo, at the height's scale, gives the hundredths."},"height_above_bore":{"label":"Top above the bore axis","kind":"length","measurements":[{"id":"photo","value":0.785,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-750-gas-block 04a45a69497d (Primary Arms BCM-LGB-750_00.jpg, 3ce1f7e276b9, an oblique view of the star face, turned square: its axis upright, its flat level, the bore's mouth as wide as tall: derived-04a45a69497d.manifest.json)","scaleRef":"the face's height, 1066.3 px (the boss's top, row 295.5, to the tab's flat, row 1361.8), as height (1.34, two sellers): 795.7 px/in","method":"the boss's top above the mouth's centre (row 920): 624.5 px of the 1066.3. The ± covers the picked edges (±5 px), where the bore's centre is taken to be (the mouth's, as an ellipse fitted to its rim) and the perspective left in (the boss is nearer the lens than the tab)","via":"harvest"}}],"note":"Not published. The top of the tube's boss above the bore's centre, as the star face shows it, at the sellers' height."},"tab_below_bore":{"label":"The set screws' flat below the bore axis","kind":"length","measurements":[{"id":"photo","value":0.555,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-750-gas-block 04a45a69497d (Primary Arms BCM-LGB-750_00.jpg, 3ce1f7e276b9, an oblique view of the star face, turned square: its axis upright, its flat level, the bore's mouth as wide as tall: derived-04a45a69497d.manifest.json)","scaleRef":"the face's height, 1066.3 px, as height (1.34, two sellers): 795.7 px/in","method":"the tab's flat (row 1361.8, level within a pixel between its two corners) below the mouth's centre (row 920): 441.8 px of the 1066.3","via":"harvest"}}]},"od":{"label":"Outside diameter of its ring about the barrel","kind":"length","measurements":[{"id":"photo","value":0.88,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/bcm-750-gas-block 04a45a69497d (Primary Arms BCM-LGB-750_00.jpg (3ce1f7e276b9), the star face turned square (its axis upright, its flat level, the bore's mouth as wide as tall): derived-04a45a69497d.manifest.json, 1200 x 1600)","scaleRef":"frame from the reviewed holes top, flat (795.7 px/in, rms 0.000 in over 2 points)","method":"width in y [-0.2, 0.2] of the traced outline (tools/trace.py); across the ring at the bore's height; the ± covers the picked edges (±5 px a side), the scale and how the face's widths are set against its heights (three gauges within 2%: the mouth's two chords 0.966, the star's proportions 0.971, the block's edges under a camera without perspective 0.949)","via":"harvest"}}],"note":"Not published. Across the ring at the bore's height in the rectified star face. How the face's widths stand against its heights in that photo has three gauges, within 2% of each other: the bore's mouth (round: its chord along the flat against its chord along the axis, 0.966, the one used), the star (a regular five-pointed star: 0.971) and the block's own edges (the flat, the axis and the long edges mutually perpendicular under a camera without perspective: 0.949, 0.92 to 0.97 between the two long edges). The first rectification, by the mouth's fitted ellipse taken whole, read 3% narrower (0.854) and left the face sheared: along its long axis the edge finder runs inside the rim."},"boss_width":{"label":"Width of the gas tube's boss on top","kind":"length","measurements":[{"id":"photo","value":0.288,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-750-gas-block 04a45a69497d (Primary Arms BCM-LGB-750_00.jpg (3ce1f7e276b9), the star face turned square (its axis upright, its flat level, the bore's mouth as wide as tall): derived-04a45a69497d.manifest.json, 1200 x 1600)","scaleRef":"frame from the reviewed holes top, flat (795.7 px/in, rms 0.000 in over 2 points)","method":"median row width in y [0.52, 0.66] (0.279–0.313) of the traced outline (tools/trace.py); the boss's neck, its sides closest","via":"harvest"}}],"note":"Not published. Across the boss's neck, where its sides are closest, in the rectified star face."},"pin_hole_from_front":{"label":"The roll pin's cross hole behind the front (star) face","kind":"length","measurements":[{"id":"photo","value":0.315,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/bcm-750-gas-block 8c329d289596 (AR15Discounts BCM-LGB-750_01.jpg: the block's right side straight on, the star face at the right, 2200 x 1467)","scaleRef":"its height, 990 px, as height (1.34, two sellers): 738.8 px/in (the side trace's scale)","method":"the hole's centre (column 1236.8, a circle through its outermost edge on 155 rays) to the front face's edge in the boss's rows (column 1469.5): 232.7 px","via":"harvest"}}],"note":"The star is on the face nearer the pin (both oblique photos), and the tube's pin is at the tube's front end: the star face is the muzzle end."},"pin_hole_d":{"label":"The roll pin's cross hole, diameter","kind":"length","measurements":[{"id":"tdp","value":0.078,"unit":"in","pm":0.003,"stated":".078 DIA +.003 THRU","source":{"type":"standard","doc":"US Army TDP drawing 8448566 (Sight, Front), rev H, PDF page 145: the hole the gas tube's pin goes through; the tube's own is the same (8448567, PDF page 144)","via":"user"},"note":"The Army's sight, not this block: the block takes the same tube and pin (BCM: \"for AR15, M16, M4, M4A1\")."},{"id":"photo","value":0.083,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/bcm-750-gas-block 8c329d289596 (AR15Discounts BCM-LGB-750_01.jpg: the block's right side straight on, 2200 x 1467)","scaleRef":"its height, 990 px, as height (1.34): 738.8 px/in","method":"a circle through the hole's outermost edge (155 rays, 1.3 px spread): 61.4 px, its edge break included","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The pin it takes is the Army's; the photo's hole, with its edge break, is 0.005 wider and within its ±."}},"pin_to_port":{"label":"The gas tube's pin hole to its gas hole","kind":"length","measurements":[{"id":"tdp","value":0.418,"unit":"in","pm":0.002,"stated":".418 ±.002","source":{"type":"standard","doc":"US Army TDP drawing 8448567 (Gas Tube Assembly), rev F, PDF page 144: the .078 pin hole to the .125 gas hole; .605 REF from the tube's front end, the pin .187 ±.003 from it","via":"user"}}]},"port_from_rear":{"label":"Its gas port ahead of its rear face","kind":"length","measurements":[{"id":"derived","value":0.275,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{bcm-750-gas-block.length} - {bcm-750-gas-block.pin_hole_from_front} - {bcm-750-gas-block.pin_to_port}"}},{"id":"tdp-sight","value":0.27,"unit":"in","pm":0.002,"stated":".270 ±.002","source":{"type":"standard","doc":"US Army TDP drawing 8448566 (Sight, Front), rev H, PDF page 145: the .125 gas port from the sight's rear face (and the pin's hole .688 ±.003 from it: .418 apart)","via":"user"},"note":"The Army's sight, not this block."}],"adopt":{"from":"derived","reason":"The block's own, by its pin hole in the photo; the Army's sight has the same within the ±."},"note":"Not published. Where the standard tube's gas hole lands when its pin is in the block's cross hole: the block's length less the pin's place behind the front face less the tube's pin-to-port. The Army's own sight has its port .270 from its rear face (8448566), the same within the photo's ±."},"tube_hole_above_bore":{"label":"The gas tube's hole, its axis above the bore (at the block)","kind":"length","measurements":[{"id":"tdp","value":0.625,"unit":"in","pm":0.003,"stated":".625 ±.003","source":{"type":"standard","doc":"US Army TDP drawing 8448566 (Sight, Front), rev H, PDF page 145: the gas tube's hole above the barrel's hole","via":"user"},"note":"The Army's sight. The receiver takes the tube .780 above the bore (8448522) and the tube's bend drops it .156 (8448567): the same height at the block."},{"id":"photo","value":0.606,"unit":"in","pm":0.035,"source":{"type":"photo","photo":"references/bcm-750-gas-block 8c329d289596 (AR15Discounts BCM-LGB-750_01.jpg: the block's right side straight on, 2200 x 1467)","scaleRef":"its height, 990 px, as height (1.34): 738.8 px/in","method":"the roll pin's hole (the pin crosses the tube's hole), its centre (row 383.9) 132.1 px below the top edge there (row 251.8): 0.179 in below the boss's top, which is height_above_bore (0.785 ± 0.03) above the bore","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The block takes the Army's tube; the pin's hole in the photo is at that height within the ±."}},"tube_hole_d":{"label":"The gas tube's hole, diameter","kind":"length","measurements":[{"id":"tdp","value":0.1805,"unit":"in","pm":0.001,"stated":".1805 DIA +.0010","source":{"type":"standard","doc":"US Army TDP drawing 8448566 (Sight, Front), rev H, PDF page 145: the gas tube's hole, to .905 ±.015 depth","via":"user"},"note":"The Army's sight, not this block."}],"note":"Not published, and no photo on file is scaled at the rear face. The Army's sight's hole for the same .180 tube."},"tube_hole_past_pin":{"label":"How far the gas tube's hole runs on ahead of the pin's hole","kind":"length","measurements":[{"id":"tdp","value":0.217,"unit":"in","pm":0.015,"stated":".905 ±.015 DEPTH; .688 ±.003","source":{"type":"standard","doc":"US Army TDP drawing 8448566 (Sight, Front), rev H, PDF page 145: the tube's hole's depth less the pin hole's distance from the same face","via":"user"},"note":"The Army's sight, not this block."}],"note":"Not published. BCM's rear-face photo (dc4f60fefbd5) shows the hole entering the boss from the rear and the star face closed. The Army's sight: the hole .905 deep, the pin .688 from the same face."},"star_center_above_bore":{"label":"The star on the front face, its centre above the bore axis","kind":"length","measurements":[{"id":"photo","value":0.552,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bcm-750-gas-block 04a45a69497d (Primary Arms BCM-LGB-750_00.jpg, 3ce1f7e276b9, an oblique view of the star face, turned square: its axis upright, its flat level, the bore's mouth as wide as tall: derived-04a45a69497d.manifest.json)","scaleRef":"the face's height, 1066.3 px, as height (1.34, two sellers): 795.7 px/in","method":"the mean of its five tips ((585.0, 390.0), (676.6, 456.5), (647.0, 556.8), (539.2, 551.8), (503.1, 447.8): picked on the first rectification and carried here): row 480.6, 439.4 px above the mouth's centre (row 920). Their mean is 10 px to one side of the axis, as the boss's neck is","via":"harvest"}}],"note":"BCM's star, laser-marked on the boss's front face (every photo of that face shows it; the rear face has the tube's hole and no star)."},"star_radius":{"label":"The star on the front face, its centre to a tip","kind":"length","measurements":[{"id":"photo","value":0.115,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/bcm-750-gas-block 04a45a69497d (Primary Arms BCM-LGB-750_00.jpg, 3ce1f7e276b9, an oblique view of the star face, turned square: its axis upright, its flat level, the bore's mouth as wide as tall: derived-04a45a69497d.manifest.json)","scaleRef":"the face's height, 1066.3 px, as height (1.34, two sellers): 795.7 px/in","method":"the five tips' mean distance from their own centre, 91.2 px (87.6 to 95.1). Tip to tip across it is 1.058 of its height from the top tip to the lower two, where a regular star is 1.052","via":"harvest"}}]}}},{"subject":"bcm-bcg","title":"BCM® Bolt Carrier Group (MPI) - Auto (BCM-BCG-AUTO)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"primary-arms","value":11.5,"unit":"oz","pm":0.05,"stated":"Weight 11.5 Oz","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Bravo Company Manufacturing 5.56 AR-15 Bolt Carrier Group - Phosphate (its number BCM-BOLT-CARRIER-GROUP-AUTO-MP), Specifications; a bullet above has \"11.5 oz weight\"","url":"https://www.primaryarms.com/bravo-company-manufacturing-bolt-carrier-group-bcm-bcg","retrieved":"2026-10-05","via":"harvest"},"note":"The seller's row, not BCM's: one decimal, so ± half its last digit."},{"id":"recoil","value":11.61,"unit":"oz","pm":0.005,"stated":"BCM Mil-spec Steel 11.61 oz","source":{"type":"spec","publisher":"review","name":"Recoil, Best Lightweight AR-15 Bolt Carrier Groups (2022): its table of weights; the text has \"our baseline Mil-spec BCM bolt carrier group weighed 11.6 ounces\" and \"we obtained a calibrated laboratory scale to precisely measure the bolt carrier groups\"","url":"https://www.recoilweb.com/best-lightweight-ar-15-bolt-carrier-groups-65941.html","retrieved":"2026-10-05","via":"harvest"},"note":"A scale reading, but of a BCM group the article doesn't name: BCM-BCG-AUTO is BCM's standard carrier group, and the article doesn't say it is this one."},{"id":"pewpew","value":11.5,"unit":"oz","pm":0.05,"stated":"BCM M16 BCG ... 11.5 oz.","source":{"type":"spec","publisher":"review","name":"Pew Pew Tactical, Best AR-15 Bolt Carrier Groups (BCG): its comparison chart","url":"https://www.pewpewtactical.com/best-ar-15-bcg-bolt-carrier-group/","retrieved":"2026-10-05","via":"harvest"},"note":"A chart's row: the article doesn't say it weighed the group, and the figure is the seller's. Not an independent reading."}],"adopt":{"from":"primary-arms","reason":"The one figure a page gives for this product by its name and number. Recoil's scale reading, 0.11 oz more, is of a BCM group it doesn't identify; it stays."},"note":"BCM gives none (its page's own weight field is empty). A seller's figure for this product and a magazine's scale reading of \"a Mil-spec BCM\" group it doesn't name, 1% apart."},"length":{"label":"The carrier's length","kind":"length","measurements":[{"id":"std","value":6.672,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.ar15.carrier_length}","via":"user"},"note":"US Army TDP drawing 8448507 (Carrier, Bolt): the tail's rear face to the front (bolt) face."}],"note":"The carrier is the standard's: BCM says \"Machined to USGI specifications\" and states no size."},"od":{"label":"The carrier's diameter","kind":"length","measurements":[{"id":"std","value":0.994,"unit":"in","pm":0.0005,"source":{"type":"derived","expr":"{std.ar15.carrier_rail_od}","via":"user"},"note":"The diameter its rails are ground to (8448507); the body and the tail are .930 (std.ar15.carrier_body_od)."}],"note":"The carrier is the standard's: BCM says \"Machined to USGI specifications\" and states no size."}}},{"subject":"bcm-carbine-action-spring","title":"BCM carbine action spring","dimensions":{"wire_d":{"label":"Wire diameter","kind":"length","measurements":[{"id":"std","value":0.072,"unit":"in","pm":0.001,"source":{"type":"derived","expr":"{std.carbine_action_spring.wire_d}","via":"harvest"}}]},"od":{"label":"Outside diameter of its coils","kind":"length","measurements":[{"id":"std","value":0.94,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{std.carbine_action_spring.od}","via":"harvest"}}]},"coils":{"label":"Total coils","kind":"count","measurements":[{"id":"photo","value":38.5,"unit":"count","pm":1,"source":{"type":"photo","photo":"references/bcm-carbine-action-spring f579fe1120ef (BCM's Spring_Carbine_Action-2: the whole spring on white, lying on the diagonal, 1028 x 1028)","scaleRef":"none: a count","method":"the crests of the spring's outline along each side of its axis (the axis is the dark pixels' principal axis): 38 on one side and 39 on the other, 27 to 35 px apart (.cache/buffer/spring/crests.py). A count of dark runs along a line inside the coils counts the near and the far strands both and isn't used","via":"harvest"}},{"id":"std","value":37.5,"unit":"count","pm":0.1,"source":{"type":"derived","expr":"{std.carbine_action_spring.coils}","via":"harvest"},"note":"The reference model's carbine spring."}],"adopt":{"from":"photo","reason":"Counted on BCM's own spring; the reference model's has a turn fewer and the reference set's table 36."}},"free_length":{"label":"Free length","kind":"length","measurements":[{"id":"std","value":10.7,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{std.carbine_action_spring.free_length}","via":"harvest"}},{"id":"photo","value":10.9,"unit":"in","pm":0.4,"source":{"type":"photo","photo":"references/bcm-carbine-action-spring f579fe1120ef (BCM's Spring_Carbine_Action-2: the whole spring on white, lying on the diagonal, 1028 x 1028)","scaleRef":"the spring's own width in the middle of its length, 104.6 px, as the Army's .940 outside diameter (std.carbine_action_spring.od): 111.3 px/in","method":"its length along its axis, 1210.8 px; at its widest (108.6 px) the same length is 10.5 in, which the ± covers","via":"harvest"}}],"adopt":{"from":"std","reason":"The standard's figure; BCM's photo of its own spring has it within the photo's ±."}},"installed_length":{"label":"Its length as installed (a carbine buffer's seat to a mil-spec carbine extension's rear wall, bolt forward)","kind":"length","measurements":[{"id":"room","value":6.972,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{bcm-receiver-extension.tube_front_behind_pin} + {bcm-receiver-extension.tube_length} - {std.receiver_extension.carbine_rear_wall} + {std.ar15.upper_rear_face_x} - {std.carbine_buffer.head_thickness}","via":"harvest"}}],"note":"What the spring is drawn at. A buffer's front face rests at the upper receiver's rear face (the carrier's rear end, bolt forward); the spring bears on the head's rear face and on the tube's rear wall inside. The reference model's assembly has 6.931 for it, with a tube 0.014 shorter and 0.027 further forward than the ledger's."},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"wire","value":1.95,"unit":"oz","pm":0.13,"source":{"type":"derived","expr":"3.14159265 * ({.od} - {.wire_d}) * {.coils} * 0.785398163 * {.wire_d} * {.wire_d} * {std.density.steel}","via":"harvest"}}],"note":"No maker's or seller's figure: BCM states none and no other seller on file lists the spring. Worked out from its wire: the wire's length round its coils times its section times what steel weighs. A derived figure, for the build's total; the ± is the coil count's, the wire's and the density's together."}}},{"subject":"bcm-carbine-buffer","title":"BCM carbine buffer","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"bcm","value":3,"unit":"oz","pm":0.05,"stated":"Weighted with 3 steel weights 3.0oz.","source":{"type":"spec","publisher":"manufacturer","name":"Bravo Company USA, Carbine Buffer (Buffer-Carbine)","url":"https://bravocompanyusa.com/carbine-buffer/","retrieved":"2026-10-12","via":"harvest"}},{"id":"primary-arms","value":3,"unit":"oz","pm":0.05,"stated":"Weight 3.0 oz.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Bravo Company Manufacturing AR-15 Buffer - Carbine (Buffer-Carbine)","url":"https://www.primaryarms.com/bravo-company-manufacturing-carbine-buffer-3-0-oz","retrieved":"2026-10-12","via":"harvest"}}],"adopt":{"from":"bcm","reason":"The seller's own figure; Primary Arms repeats it."}},"length":{"label":"Length (the head's front face to the bumper's end)","kind":"length","measurements":[{"id":"std","value":3.251,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.carbine_buffer.length}","via":"harvest"},"note":"BCM states no size. Its side photo on white (c75e44c92794, 1280 x 491) has the head 0.29 and the body 0.20 of the length, where these figures have 0.30 and 0.21."}]},"od":{"label":"Diameter (its head, which runs in the extension's bore)","kind":"length","measurements":[{"id":"std","value":0.98,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.carbine_buffer.head_d}","via":"harvest"}}]}}},{"subject":"bcm-castle-nut","title":"BCM receiver extension nut (castle nut)","dimensions":{"rear_face_behind_pin":{"label":"Castle nut rear face behind takedown pin","kind":"length","measurements":[{"id":"photo","value":1.74,"unit":"in","stated":"about 1.74 in","source":{"type":"photo","photo":"not recorded in brief","scaleRef":"not recorded in brief","method":"calibrated photo measurement","via":"brief"}},{"id":"stack","value":1.668,"unit":"in","source":{"type":"derived","expr":"{bad-workhorse-lower.rear_behind_pin} + {bcm-end-plate.thickness} + {.thickness}","via":"user"},"note":"The receiver's rear face (the Army's drawing, M6), plus the end plate and castle nut stacked behind it (thicknesses measured on an Aero lower). Until M6 the stack stood on the Workhorse's photo-read ring, 0.037 further back."}],"adopt":{"from":"stack","reason":"Built from the standard's rear face and measured hardware. The brief's 1.74 (photo not archived) is 0.07 more; Magpul's whole-rifle photo of an M4 with their stock (references/magpul-moe-carbine 314f5e1b0872, rail-scaled) reads 1.67."}},"od":{"label":"Castle nut OD","kind":"length","measurements":[{"id":"photo","value":1.32,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-stock-kit b6118d35ed00 (Aero Precision M4E1 complete lower with MOE SL, straight right side, 2000 px; supplied in chat)","scaleRef":"pin frame: takedown, pivot, trigger, hammer, selector (Hough-refined), 130.6 px/in, rms 0.022 in","method":"castle nut silhouette height, x −1.55 to −1.16 (the nut's notches are on its rear face, not its outline)","via":"user"},"note":"Aero's kit nut. Read at a scale 2.5% too large (2026-10-05: the same five features fit the Army drawing's positions at 127.4 px/in, rms 0.003 in): the silhouette is 173 px tall, 1.36 in at the pins' scale and up to 1.38 at the tube's own, which is the other makers' nuts."},{"id":"strike","value":34.92,"unit":"mm","stated":"Width: 34.92mm  Height: 10.5mm","source":{"type":"spec","publisher":"manufacturer","name":"Strike Industries anti-rotation castle nut (not BCM)","url":"https://www.strikeindustries.com/si-ar-cn.html","retrieved":"2026-09-30","via":"harvest"},"note":"The page doesn't define its axes; the width reads as the OD."},{"id":"retail-3317","value":1.375,"unit":"in","stated":"Length: 1.375\"","source":{"type":"spec","publisher":"retailer","name":"Shooting Sports Supplies, (3317) AR15 mil-spec/commercial castle nut (not BCM)","url":"https://www.shootingsportssupplies.com/a-15463657/buttstocks-accessoires/3317-ar15-mil-spec-commercial-castle-nut/","retrieved":"2026-09-30","via":"harvest"},"note":"Axis unlabeled; the same size as Strike's width."},{"id":"forum","value":1.36,"unit":"in","stated":"Castle nut OD: 1.36\"","source":{"type":"spec","publisher":"forum","name":"M4Carbine.net, CHoffman (Stag mil-spec nut, micrometer)","url":"https://m4carbine.net/t/castle-nut-and-receiver-extension-tube-dimensions/124766","retrieved":"2026-09-30","via":"harvest"},"note":"Hand measurement, nearest hundredth; the poster notes nuts vary by maker."},{"id":"model","value":1.363,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"one cylinder, r 0.6815 (.cache/buffer/std/faces.Buffer_Tube_Nut.txt)","via":"user"},"note":"A mil-spec nut as the reference model has it (2026-10-12): the forum's micrometer reading to the hundredth, 0.012 under the figure adopted."}],"adopt":{"from":"strike","reason":"A manufacturer figure for a mil-spec nut; the retailer listing matches it. The forum micrometer reading of a third brand is 0.015 in smaller."},"note":"BCM publishes no castle-nut dimensions. These are other brands' mil-spec nuts, which are interchangeable parts, so the BCM nut's OD stays unconfirmed."},"thickness":{"label":"Castle nut thickness","kind":"length","measurements":[{"id":"strike","value":10.5,"unit":"mm","stated":"Height: 10.5mm","source":{"type":"spec","publisher":"manufacturer","name":"Strike Industries anti-rotation castle nut (not BCM)","url":"https://www.strikeindustries.com/si-ar-cn.html","retrieved":"2026-09-30","via":"harvest"},"note":"Axis undefined; read as the thickness along the tube. A different brand and design (anti-rotation)."},{"id":"photo","value":0.39,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-stock-kit b6118d35ed00 (Aero Precision M4E1 complete lower with MOE SL, straight right side, 2000 px; supplied in chat)","scaleRef":"pin frame: takedown, pivot, trigger, hammer, selector (Hough-refined), 130.6 px/in, rms 0.022 in","method":"castle nut silhouette length along the tube, x −1.553 to −1.16","via":"user"},"note":"Read at a scale 2.5% too large, and to an edge inside the end plate (2026-10-05): on a 6x crop the nut runs from column 949 to 995.5, 46.5 px, which is 0.37 ± 0.02 in at the tube's own scale (125 ± 2 px/in; the pins' is 127.4)."},{"id":"model","value":0.3765,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"its front face to its rear face, planes y 0 and y 0.3765","via":"user"},"note":"A mil-spec nut as the reference model has it (2026-10-12): it and the photo's reading at its true scale (0.37 ± 0.02) are two sources 0.04 under the figure adopted, which is another design's. Still not changed: three stocks' seats are checked against the nut's rear face, and they want checking again with it."}],"adopt":{"from":"strike","reason":"A manufacturer's figure, for another maker's nut of another design. The user's photo of Aero's nut was taken to agree within its ±; read again at its true scale (2026-10-05) it is 0.37 ± 0.02 in, 0.04 less: the kit's nut may be drawn that much too long, its rear face that much too far back. Not changed here: the nut's rear face is what three stocks' seats are checked against."},"note":"BCM publishes none."},"notch_width":{"label":"Castle nut wrench notch width","kind":"length","measurements":[{"id":"forum","value":0.16,"unit":"in","pm":0.005,"stated":"Nut Notch width: .16","source":{"type":"spec","publisher":"forum","name":"M4Carbine.net, CHoffman (Stag mil-spec nut, micrometer, 'approximate and to the nearest hundredth')","url":"https://m4carbine.net/t/castle-nut-and-receiver-extension-tube-dimensions/124766","retrieved":"2026-10-01","via":"harvest"}},{"id":"model","value":0.162,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"a wrench notch's two side planes, ±0.0810","via":"user"}}],"adopt":{"from":"forum","reason":"A micrometer on a real mil-spec nut; the reference model's nut has 0.162, the same within two thousandths."},"note":"BCM's nut has four wrench notches in its rear face, about 90° apart, cut through its wall (BCM's photo, references/bcm-stock-kit adab0cb43def); a staking notch on the front face isn't drawn."},"notch_depth":{"label":"Castle nut wrench notch depth (into the rear face)","kind":"length","measurements":[{"id":"forum","value":0.11,"unit":"in","pm":0.02,"stated":"Nut Notch depth: .11 (hard to get an accurate measurement when installed)","source":{"type":"spec","publisher":"forum","name":"M4Carbine.net, CHoffman (Stag mil-spec nut, micrometer)","url":"https://m4carbine.net/t/castle-nut-and-receiver-extension-tube-dimensions/124766","retrieved":"2026-10-01","via":"harvest"},"note":"± widened for the poster's caveat."},{"id":"model","value":0.1375,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"a wrench notch's floor plane, y 0.2390 of 0.3765","via":"user"},"note":"0.0275 deeper than the forum's reading of an installed nut, just outside its ±."}],"adopt":{"from":"forum","reason":"A reading on a real nut, which its poster calls hard to take with the nut installed; the reference model's nut has its notches 0.1375 deep, 0.0275 more and just outside this figure's ±. Kept: the model is another nut."}},"notches":{"label":"Castle nut wrench notches","kind":"count","measurements":[{"id":"bcm","value":4,"unit":"count","source":{"type":"photo","photo":"references/bcm-stock-kit adab0cb43def (BCM castle nut, three-quarter view from above)","scaleRef":"none (a count)","method":"counted on the rear face, about 90° apart","via":"harvest"}}]},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"metal","value":0.7,"unit":"oz","pm":0.07,"source":{"type":"derived","expr":"(0.785398163 * ({.od} * {.od} - {std.receiver_extension.thread_major_d} * {std.receiver_extension.thread_major_d}) * {.thickness} - {.notches} * {.notch_width} * {.notch_depth} * ({.od} - {std.receiver_extension.thread_major_d}) / 2) * {std.density.steel}","via":"harvest"}}],"note":"No maker's or seller's figure: BCM states none. Worked out from its sizes: a steel ring of its outside diameter and thickness round the extension's thread, less its four wrench notches. A derived figure, for the build's total; its thickness may be 0.04 in long (that figure's note), which would make this 9% heavy."},"staking_notches":{"label":"Castle nut staking notches, in its front face's outer edge","kind":"count","measurements":[{"id":"model","value":3,"unit":"count","source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"three notches 120 degrees apart, counted in the face list (planes #20197, #20323 and their like)","via":"user"}}]},"staking_notch_width":{"label":"Castle nut staking notch, width","kind":"length","measurements":[{"id":"model","value":0.09,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"a notch's two side planes, ±0.0450","via":"user"}}]},"staking_notch_depth":{"label":"Castle nut staking notch, depth into the front face","kind":"length","measurements":[{"id":"model","value":0.082,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"a notch's floor","via":"user"}}]},"staking_notch_radial":{"label":"Castle nut staking notch, how far in from the outside it is cut","kind":"length","measurements":[{"id":"model","value":0.075,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the notch's inner wall, a cylinder r 0.6065 of an outside r 0.6815","via":"user"}}]}}},{"subject":"bcm-delta-ring-assembly","title":"BCM Delta Ring Assembly - AR15","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"metal","value":1.29,"unit":"oz","pm":0.1,"source":{"type":"derived","expr":"0.785398163 * {std.ar15.slip_ring_land} * (7 * {std.ar15.slip_ring_od} * {std.ar15.slip_ring_od} - 84 * {std.ar15.slip_ring_step} * {std.ar15.slip_ring_od} + 364 * {std.ar15.slip_ring_step} * {std.ar15.slip_ring_step}) * {std.density.aluminium_7075} - 0.785398163 * ({std.ar15.slip_ring_bore_d} * {std.ar15.slip_ring_bore_d} * {std.ar15.slip_ring_bore_depth} + {std.ar15.slip_ring_lip_hole_d} * {std.ar15.slip_ring_lip_hole_d} * ({std.ar15.slip_ring_length} - {std.ar15.slip_ring_bore_depth} - {std.ar15.slip_ring_skirt_length}) + {std.ar15.slip_ring_skirt_d} * {std.ar15.slip_ring_skirt_d} * {std.ar15.slip_ring_skirt_length}) * {std.density.aluminium_7075} + {std.ar15.slip_ring_spring_sections} * {std.ar15.slip_ring_spring_strip} * ({std.ar15.slip_ring_spring_od} - {std.ar15.slip_ring_spring_id}) / 2 * (3.14159265 * ({std.ar15.slip_ring_spring_od} + {std.ar15.slip_ring_spring_id}) / 2 - {std.ar15.slip_ring_spring_gap}) * {std.density.steel} + 0.785398163 * ({std.ar15.slip_ring_retainer_od} * {std.ar15.slip_ring_retainer_od} - {std.ar15.slip_ring_retainer_id} * {std.ar15.slip_ring_retainer_id}) * {std.ar15.slip_ring_retainer_thickness} * {std.density.steel}","via":"harvest"},"note":"The seven lands taken at .086 each (0.602 for the drawing's .600). The ring's share is 0.85 oz, the spring's 0.27, the snap ring's 0.16."}],"note":"No maker's or seller's figure: BCM states none (its page's markup has \"weight\":null). Worked out from the drawings' sizes: the ring as 7075 aluminium (the drawing's \"ALUMINUM ALLOY 7075-T6\"), its seven lands turned less its bore, lip hole and skirt (the gas tube's notch, 0.002 cubic inches, left in); the weld spring as its four sections of steel strip round their mean circle less the gap; the snap ring as a flat steel ring (its ID the model's free one, its ends' holes left in). A derived figure, for the build's total; the model's volume of each piece is held to its share in app/tests/bcm-delta-ring-assembly.test.ts."},"outside_diameter":{"label":"Outside diameter","kind":"length","measurements":[{"id":"standard","value":2.1,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.ar15.slip_ring_od}","via":"harvest"}}],"note":"BCM states none. The Army's drawing's: BCM's photo shows the drawing's ring (seven lands, the lip's notch), and BCM sells it \"for your AR15, M16, M4\", the rifles the drawing is \"USED ON\". Its largest, at the rear land; the front land is std.ar15.slip_ring_front_od."},"length":{"label":"Length along the bore","kind":"length","measurements":[{"id":"standard","value":0.6,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.ar15.slip_ring_length}","via":"harvest"},"note":"The ring's, the drawing's. The assembly as drawn on a nut runs from the snap ring's rear face to the ring's front, 0.724."}]},"lands":{"label":"The lands round the ring's outside","kind":"count","measurements":[{"id":"photo","value":7,"unit":"count","pm":0,"source":{"type":"photo","photo":"references/bcm-delta-ring-assembly 96d01c941da6 (BCM's photo of the three parts laid out, 1024 px)","scaleRef":"none (a count)","method":"counted on the ring's outside down its near side, from the rear face's land to the front's, each step a dark line under a lit land","via":"harvest"}},{"id":"standard","value":7,"unit":"count","pm":0,"source":{"type":"derived","expr":"{std.ar15.slip_ring_steps} + 1","via":"harvest"}}],"adopt":{"from":"standard","reason":"The drawing's six steps; BCM's photo has the same count."}}}},{"subject":"bcm-end-plate","title":"BCM receiver end plate","dimensions":{"thickness":{"label":"End plate thickness","kind":"length","measurements":[{"id":"photo","value":0.13,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-stock-kit b6118d35ed00 (Aero Precision M4E1 complete lower with MOE SL, straight right side, 2000 px; supplied in chat)","scaleRef":"pin frame: takedown, pivot, trigger, hammer, selector (Hough-refined), 130.6 px/in, rms 0.022 in","method":"silhouette step between the castle nut (1.32 in tall) and the plate (1.97 in tall), x −1.16 to −1.03 behind the takedown pin","via":"user"},"note":"Aero's kit plate; BCM's is taken to be the same mil-spec thickness. Read at a scale 2.5% too large (2026-10-05): on a 6x crop the plate runs from column 995.5 to 1013.5, 18 px, which is 0.14 in at the tube's own scale (125 ± 2 px/in): inside this ±."},{"id":"model","value":0.124,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the plate's two faces, planes y 0 and y 0.1240 (.cache/buffer/std/faces.Buffer_Tube_Rotation_Lock.txt)","via":"user"},"note":"A mil-spec plate as the reference model has it (2026-10-12): inside the photo's ±."}],"adopt":{"from":"photo","reason":"Read on a real plate installed; the reference model's mil-spec plate is 0.124, inside its ±."}},"top_above_axis":{"label":"End plate top above the tube axis","kind":"length","measurements":[{"id":"bcm-kit","value":0.69,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-stock-kit 43b31cee68d4 (BCM: the kit assembled for display, side view on white, 1200 px; the nut sits ahead of the plate, reversed, so sizes only)","scaleRef":"the tube's top to its rail's bottom = 1.441 in (Magpul's partial drawing of the mil-spec carbine tube, scaled from its vectors by the research agent: 0.574 + 0.867; Magpul's identification card and a forum caliper reading, 1.45, agree), 138 px → 95.8 px/in; the tube reads 138 px from x 800 to 1100, so the view is near orthographic","method":"the plate's top edge (column extents x 462–482) above the tube axis (the tube's top + half its 1.146 OD)","via":"harvest"}},{"id":"photo","value":0.65,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-stock-kit b6118d35ed00 (Aero Precision M4E1 complete lower with MOE SL, straight right side, 2000 px; supplied in chat)","scaleRef":"pin frame: takedown, pivot, trigger, hammer, selector (Hough-refined), 130.6 px/in, rms 0.022 in","method":"plate top 1.54 in above the pin line; tube axis 0.89 in (the castle nut's centre)","via":"user"}},{"id":"model","value":0.6817,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the ring's radius, r 0.6817","via":"user"}}],"adopt":{"from":"bcm-kit","reason":"BCM's own plate in a near-orthographic view; the Aero photo's plate (another maker's, at the lens's compressed edge) agrees within its ±."}},"bottom_below_axis":{"label":"End plate tab bottom below the tube axis","kind":"length","measurements":[{"id":"bcm-kit","value":1.316,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-stock-kit 43b31cee68d4 (BCM: the kit assembled for display, side view on white, 1200 px; the nut sits ahead of the plate, reversed, so sizes only)","scaleRef":"the tube's top to its rail's bottom = 1.441 in (Magpul's partial drawing of the mil-spec carbine tube, scaled from its vectors by the research agent: 0.574 + 0.867; Magpul's identification card and a forum caliper reading, 1.45, agree), 138 px → 95.8 px/in; the tube reads 138 px from x 800 to 1100, so the view is near orthographic","method":"the lobe's bottom edge (x 470–478) below the tube axis","via":"harvest"}},{"id":"photo","value":1.32,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-stock-kit b6118d35ed00 (Aero Precision M4E1 complete lower with MOE SL, straight right side, 2000 px; supplied in chat)","scaleRef":"pin frame: takedown, pivot, trigger, hammer, selector (Hough-refined), 130.6 px/in, rms 0.022 in","method":"plate bottom 0.43 in below the pin line; tube axis 0.89 in","via":"user"}},{"id":"model","value":1.3788,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the lobe's round end, r 0.4266 about a centre 0.9522 below the axis","via":"user"},"note":"Another plate than BCM's: 0.06 lower than BCM's own, inside what this figure's notes give for Aero's."}],"adopt":{"from":"photo","reason":"The two photos agreed to the hundredth as first read. The user's was read at a scale 2.5% too large (2026-10-05: its pins fit the Army drawing's positions at 127.4 px/in, not 130.6): at its true scale its plate's lobe ends 1.35 to 1.38 in below the axis, which is Aero's plate; BCM's own photo has 1.316, 0.004 from the figure kept."},"note":"The tab that covers the takedown-pin detent hole."},"height":{"label":"End plate height (its top to its lobe's bottom)","kind":"length","measurements":[{"id":"derived","value":2.006,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.top_above_axis} + {.bottom_below_axis}","via":"harvest"}},{"id":"faceon-hole","value":2.065,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-stock-kit 83b50e3b0f38 (BCM receiver end plate, straight face-on, 623 x 800)","scaleRef":"the ring's hole, 330 px across, taken as the 1.185 in it must clear (the tube's threads, Magpul's partial drawing): a lower bound on the hole, so on this height","method":"the outline's height, 575 px (luminance < 150, largest piece, holes filled); at this scale the plate's top stands 0.707 above the hole's centre (the side photos: 0.69)","via":"harvest"}}],"adopt":{"from":"derived","reason":"Two side photos measure the plate against the tube axis directly; the face-on photo's hole-scaled height is a lower bound that agrees within the ±. At the adopted scale the traced ring's centre falls 0.003 in from the axis."},"note":"What the face-on photo of BCM's plate (profiles.end_plate) is scaled to."},"face_mean_width":{"label":"Its face's area over its height (the width of a rectangle as tall with the same area)","kind":"length","measurements":[{"id":"outline","value":0.974,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-stock-kit 83b50e3b0f38 (BCM receiver end plate, straight face-on, 623 x 800)","scaleRef":"the traced outline's own scale (profiles.face: its height, .height)","method":"the traced outline's area (1.954 square inches, the hole and the boss filled) over its height (2.006 in)","via":"harvest"}}],"note":"A way to hold the outline's area as a length: what the plate's weight is worked out from."},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"metal","value":0.51,"unit":"oz","pm":0.12,"source":{"type":"derived","expr":"({.face_mean_width} * {.height} - 0.785398163 * {std.receiver_extension.thread_major_d} * {std.receiver_extension.thread_major_d}) * {.thickness} * {std.density.steel}","via":"harvest"}}],"note":"No maker's or seller's figure: BCM states none. Worked out from its sizes: its face's area less the hole for the extension's thread, through its thickness, as steel (BCM states no material for this plate; its QD plate is steel, and a plate that is staked is). A derived figure, for the build's total; nearly all of its ± is the thickness's, read to ± 0.03 on a photo."},"boss_proud":{"label":"End plate, how far its boss stands out of its front face","kind":"length","measurements":[{"id":"model","value":0.0645,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the boss's face, plane y 0.1885 of a plate 0.1240 thick","via":"user"}}]},"boss_width":{"label":"End plate, its boss side to side","kind":"length","measurements":[{"id":"model","value":0.496,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"an obround: two r 0.1875 ends at x ±0.0605","via":"user"}}]},"boss_height":{"label":"End plate, its boss top to bottom","kind":"length","measurements":[{"id":"model","value":0.375,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the obround's two ends' diameter","via":"user"}}]},"boss_below_axis":{"label":"End plate, its boss's middle below the tube's axis","kind":"length","measurements":[{"id":"model","value":0.9974,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the obround's centre","via":"user"}}]},"dimple_depth":{"label":"End plate, the dimple in its rear face behind the boss","kind":"length","measurements":[{"id":"model","value":0.063,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"plane y 0.0630; the dimple is the boss's outline 0.005 larger all round","via":"user"}}]}}},{"subject":"bcm-front-sight-base-f-750","title":"BCM Front Sight Base F - FSB (ID .750) - Milspec for Flat Top Uppers (Front-Sight-Base-F-750)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"metal","value":5.56,"unit":"oz","pm":0.4,"source":{"type":"derived","basis":"The model's volume times std.density.steel: worked out from the figures in this ledger, not a reading.","via":"harvest"}}],"note":"WORKED OUT, not published: BCM states no weight, nor does Primary Arms. Its own steel: the model's volume (pipeline/blender/bcm_front_sight_base_f_750.py, its manifest's volume_in3, the base alone without its two taper pins: 1.218 in3, built from the figures below) times std.density.steel (4.565 oz/in3), held to it by app/tests/bcm-front-sight-base-f-750.test.ts. The ± covers the widths the CAD set gives (about 0.01 in round a side of 2.6 in2) and the density's range."},"journal_id":{"label":"Bore (the journal it fits: .750 or .625)","kind":"length","measurements":[{"id":"bcm","value":0.75,"unit":"in","pm":0.001,"stated":"Front Sight Base F - FSB (ID .750) - Milspec for Flat Top Uppers","source":{"type":"spec","publisher":"manufacturer","name":"Bravo Company USA, Front Sight Base F - FSB (ID .750) - Milspec for Flat Top Uppers (Front-Sight-Base-F-750), its name and its description (\"(.750\")\")","url":"https://bravocompanyusa.com/front-sight-base-f-fsb-id-750-milspec-for-flat-top-uppers/","retrieved":"2026-10-28","via":"harvest"}},{"id":"model","value":0.75,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"the bore, a cylinder r 0.375 on its z axis through both rings","via":"user"}}],"adopt":{"from":"bcm","reason":"The maker's figure; the CAD set's base is bored the same."},"note":"BCM's .625 base is another product (Front Sight Base F - FSB (ID .625))."},"length":{"label":"Length along the barrel, the rear face to the rings' front face","kind":"length","measurements":[{"id":"model","value":1.804,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"the rear face (plane z -1.804) to the front face (plane z 0, from the ring's foot to the tower's top)","via":"user"}},{"id":"photo","value":1.816,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/bcm-front-sight-base-f-750 e1fa9fe8e586 (Primary Arms Front-Sight-Base-F-750_01.jpg: BCM's base from its right side, straight on, the muzzle at the right, 2200 x 1467)","scaleRef":"frame from the reviewed holes pin, rear (365.7 px/in): the roll pin's hole and the rear face on its row, .688 apart (8448566)","method":"x_max less x_min of the traced outline on the rings' rows (y -0.2 to 0.6): 1.542 + 0.274 (the 215 level, which keeps the front face's lit edge)","via":"harvest"}}],"adopt":{"from":"model","reason":"The CAD set's faces; BCM's own base in the side photo agrees within 0.012 in."},"note":"Not published. The Army's drawing gives 1.750 for its .625 base (8448566, side view), which isn't this one's ring."},"lug_past_front":{"label":"The bayonet lug's front face ahead of the rings' front face","kind":"length","measurements":[{"id":"model","value":0.325,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"the lug's front face, plane z 0.325","via":"user"}},{"id":"photo","value":0.314,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bcm-front-sight-base-f-750 e1fa9fe8e586 (Primary Arms Front-Sight-Base-F-750_01.jpg: BCM's base from its right side, straight on, the muzzle at the right, 2200 x 1467)","scaleRef":"frame from the reviewed holes pin, rear (365.7 px/in): the roll pin's hole and the rear face on its row, .688 apart (8448566)","method":"the outline's x_max (the lug's front, 1.856) less its x_max on the rings' rows (1.542)","via":"harvest"}}],"adopt":{"from":"photo","reason":"BCM's own base: its side outline, which the model draws, ends here; the CAD set's lug is 0.011 longer, within the two readings' ±."}},"port_from_rear":{"label":"Its gas port ahead of its rear face","kind":"length","measurements":[{"id":"tdp","value":0.27,"unit":"in","pm":0.002,"stated":".270 ±.002","source":{"type":"standard","doc":"US Army TDP drawing 8448566 (Sight, Front), rev H, PDF page 145, side view: the .125 gas port from the rear face","via":"user"}},{"id":"model","value":0.27,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"the port's .145 counterbore, a cylinder on y at z -1.534: 0.270 ahead of the rear face","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing; the CAD set's .750 base has the same."}},"pin_hole_from_rear":{"label":"The gas tube's roll pin hole ahead of the rear face","kind":"length","measurements":[{"id":"tdp","value":0.688,"unit":"in","pm":0.003,"stated":".688 ±.003","source":{"type":"standard","doc":"US Army TDP drawing 8448566 (Sight, Front), rev H, PDF page 145, side view: the .078 roll pin hole from the rear face","via":"user"}}]},"pin_to_port":{"label":"The gas tube's pin hole ahead of the port","kind":"length","measurements":[{"id":"derived","value":0.418,"unit":"in","pm":0.004,"source":{"type":"derived","expr":"{.pin_hole_from_rear} - {.port_from_rear}"}},{"id":"tdp-tube","value":0.418,"unit":"in","pm":0.002,"stated":".418 ±.002","source":{"type":"standard","doc":"US Army TDP drawing 8448567 (Gas Tube Assembly), rev F, PDF page 144: the .078 pin hole to the .125 gas hole","via":"user"}}],"adopt":{"from":"derived","reason":"The base's own two callouts; the tube's drawing puts its gas hole the same distance behind its pin, as it must."}},"pin_hole_d":{"label":"The roll pin's cross hole, diameter","kind":"length","measurements":[{"id":"tdp","value":0.078,"unit":"in","pm":0.003,"stated":".078 DIA +.003 THRU","source":{"type":"standard","doc":"US Army TDP drawing 8448566 (Sight, Front), rev H, PDF page 145, side view","via":"user"}}]},"tube_hole_above_bore":{"label":"The gas tube's hole, its axis above the bore","kind":"length","measurements":[{"id":"tdp","value":0.625,"unit":"in","pm":0.003,"stated":".625 ±.003","source":{"type":"standard","doc":"US Army TDP drawing 8448566 (Sight, Front), rev H, PDF page 145, rear end view: the gas tube's hole above the barrel's hole","via":"user"}},{"id":"model","value":0.625,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"the tube's hole, a cylinder r 0.0902 along z at y 0.625","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing; the CAD set has the same."}},"tube_hole_d":{"label":"The gas tube's hole, diameter","kind":"length","measurements":[{"id":"tdp","value":0.1805,"unit":"in","pm":0.001,"stated":".1805 DIA +.0010","source":{"type":"standard","doc":"US Army TDP drawing 8448566 (Sight, Front), rev H, PDF page 145, side view","via":"user"}}]},"tube_hole_depth":{"label":"The gas tube's hole, its depth from the rear face","kind":"length","measurements":[{"id":"tdp","value":0.905,"unit":"in","pm":0.015,"stated":".905 ±.015 DEPTH","source":{"type":"standard","doc":"US Army TDP drawing 8448566 (Sight, Front), rev H, PDF page 145, side view and View A","via":"user"}}]},"post_from_rear":{"label":"The post's axis ahead of the rear face","kind":"length","measurements":[{"id":"tdp","value":1.45,"unit":"in","pm":0.005,"stated":"1.450","source":{"type":"standard","doc":"US Army TDP drawing 8448566 (Sight, Front), rev H, PDF page 145, side view: the rear face to the post's hole (a three-place figure: ±.005 by the title block)","via":"user"}},{"id":"model","value":1.45,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"the post's threaded hole, cylinders r 0.069 and 0.082 on y at z -0.354","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing; the CAD set has the same."}},"a2_post_seat_above_bore":{"label":"An A2 base's tower top (the floor between the wings the post rises from) above the bore","kind":"length","measurements":[{"id":"tdp","value":2.285,"unit":"in","pm":0.01,"stated":"2.285 ±.010","source":{"type":"standard","doc":"US Army TDP drawing 8448566 (Sight, Front), rev H, PDF page 145, front end view: the barrel's hole's centre to the floor between the wings","via":"user"}}],"note":"The Army's base, for a carry handle's rear sight: not this one (post_seat_above_bore)."},"f_over_a2":{"label":"How much taller a flat-top's \"F\" base is than the A2's","kind":"length","measurements":[{"id":"windham-post","value":0.04,"unit":"in","pm":0.005,"stated":"For use with the Colt A4 Removable Carry Handle or other “Mil-Spec” height carry handles or rear flip sights , the .040 taller Sight Post is required in the A2 Standard Front Sight Base on carbine length sighting planes .","source":{"type":"spec","publisher":"retailer","name":"Windham Weaponry shop, Front Sight Post 040 Height (SKU 9349056-mod), Description","url":"https://shop.windhamweaponry.com/?p=1084","retrieved":"2026-10-28","via":"harvest"}},{"id":"windham-article","value":0.04,"unit":"in","pm":0.005,"stated":"how it really doesn’t make a great deal of difference whether the front sight base is the taller “F” marked or not. It usually boils down to a few extra clicks of front sight post adjustment which if excessive, can easily be remedied with a .040″ taller front sight post.","source":{"type":"spec","publisher":"review","name":"Windham Weaponry, \"Why don’t you use ‘F’ marked front sight bases?\"","url":"https://windhamweaponry.com/?p=21839","retrieved":"2026-10-28","via":"harvest"}}],"adopt":{"from":"windham-post","reason":"The product page states the figure for the flat-top's carry handle; the article says the same post makes up the F base's height."},"note":"BCM: \"Mil-Spec for rifles issued to the troops require taller front sight bases on all flat top AR rifles.\" and \"Designed to match the height of Mil-Spec height rear iron sights.\" (no figure). Windham Weaponry sells a post .040 taller for an A2 base under a flat-top's carry handle, and says that post makes up the F base's height. Two of one maker's pages; no drawing of the F base is on file."},"post_seat_above_bore":{"label":"The tower's top (the floor between the wings the post rises from) above the bore","kind":"length","measurements":[{"id":"derived","value":2.325,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{.a2_post_seat_above_bore} + {.f_over_a2}"}}],"note":"Where the post's anchor is (the interface's \"top of the tower\"). The A2's drawn height and the F's difference."},"height_above_bore":{"label":"Top above the bore axis (the wings' tips)","kind":"length","measurements":[{"id":"photo","value":2.615,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-front-sight-base-f-750 e1fa9fe8e586 (Primary Arms Front-Sight-Base-F-750_01.jpg: BCM's base from its right side, straight on, the muzzle at the right, 2200 x 1467)","scaleRef":"frame from the reviewed holes pin, rear (365.7 px/in, rms 0.000 in over 2 points)","method":"y_max of the traced outline (tools/trace.py); the wings' tips: the outline's top, above the bore's axis, which lies .625 below the roll pin's hole (the tube's axis: 8448566)","via":"harvest"}}],"note":"Not published. The wings' rounded tips, the base's highest point, as BCM's base shows them in the side photo."},"ring_r":{"label":"The rings' outside radius about the bore","kind":"length","measurements":[{"id":"model","value":0.44,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"the rings' round upper part, cylinders r 0.44 on its z axis (the rear ring's, z -1.804 to -1.394; the front ring's a torus 0.41 + 0.03 at its edge)","via":"user"}}],"note":"Both rings, the round part above the flats at their feet. The Army's drawing's ring is a .625 base's."},"ring_flat_half":{"label":"The rings' feet: half their width across the flats","kind":"length","measurements":[{"id":"model","value":0.375,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"the planes x ±0.375 under both rings (from y -0.230 down to the rear ring's foot, from -0.239 to the front ring's)","via":"user"}}],"note":"Both rings come down square below the bore, their sides flat and their foot flat, as BCM's base's two photos show."},"ring_flat_top":{"label":"Where the rings' flat sides begin, below the bore","kind":"length","measurements":[{"id":"model","value":0.23,"unit":"in","pm":0.01,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"the planes x ±0.375 begin at y -0.2302 (rear ring) and -0.2385 (front ring), where they meet the round of r 0.44","via":"user"}}]},"rear_ring_length":{"label":"The rear ring's length from the rear face","kind":"length","measurements":[{"id":"model","value":0.44,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"the rear face (z -1.804) to the rear ring's front face (plane z -1.364)","via":"user"}}]},"front_ring_length":{"label":"The front ring's length behind the front face","kind":"length","measurements":[{"id":"model","value":0.458,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"the front ring's rear face (plane z -0.458) to the front face (z 0)","via":"user"}}]},"rear_ring_foot":{"label":"The rear ring's flat foot below the bore","kind":"length","measurements":[{"id":"model","value":0.509,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"the plane y -0.5088 under the rear ring, between the swivel's ears and the flats","via":"user"}}]},"front_ring_foot":{"label":"The front ring's flat foot below the bore","kind":"length","measurements":[{"id":"model","value":0.475,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"the plane y -0.475 under the front ring, each side of the bayonet lug's stem","via":"user"}}]},"boss_half":{"label":"The gas tube's boss between the legs: half its width","kind":"length","measurements":[{"id":"model","value":0.155,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"the boss's sides, planes x ±0.155 from z -1.661 to -0.165 (y 0.478 to 0.696)","via":"user"}}],"note":"The bar the gas tube runs in, between the two legs, over the gap between the rings (both photos)."},"boss_top":{"label":"The boss's top above the bore","kind":"length","measurements":[{"id":"model","value":0.834,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"its top, plane y 0.8337 (between its rounds of r 0.149 about y 0.696)","via":"user"}}]},"boss_round_r":{"label":"The boss's top edges: their radius","kind":"length","measurements":[{"id":"model","value":0.149,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"cylinders r 0.1492 along z about (x ±0.006, y 0.6957)","via":"user"}}]},"rear_leg_thickness":{"label":"The rear leg at its foot: the rear face to its front face","kind":"length","measurements":[{"id":"model","value":0.143,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"the rear face (z -1.804) to the plane z -1.661 that the window's foot and the boss's rear end stand on","via":"user"}}]},"front_leg_rear":{"label":"The front leg's rear face, ahead of the rear face","kind":"length","measurements":[{"id":"model","value":1.639,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"the plane z -0.165 (the window's front side, from the rings up to y 1.986)","via":"user"}}]},"window_top":{"label":"The window's top above the bore","kind":"length","measurements":[{"id":"model","value":1.986,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"the plane y 1.9857 between the sloped rear leg and the front leg (z -0.786 to -0.165)","via":"user"}}]},"tower_foot_half":{"label":"The tower's sides at their foot: half the width","kind":"length","measurements":[{"id":"model","value":0.4384,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"the tower's two side planes (normals ±(0.9963, 0.086, 0)) at their foot, (±0.4384, 0.0378): the sides lean in going up","via":"user"}}]},"tower_foot_y":{"label":"The tower's sides' foot above the bore","kind":"length","measurements":[{"id":"model","value":0.038,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"the side planes' lowest vertices, y 0.0378, where they meet the rings' round","via":"user"}}]},"tower_top_half":{"label":"The tower's sides at their top (under the wings): half the width","kind":"length","measurements":[{"id":"model","value":0.239,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"the side planes' highest vertices, (±0.239, 2.3487), where the wings' outer faces begin","via":"user"}}]},"tower_side_top_below_seat":{"label":"The tower's sides' top below the floor between the wings","kind":"length","measurements":[{"id":"model","value":0.005,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"the side planes end at y 2.3487, the floor between the wings (planes y 2.3537) 0.005 above","via":"user"}}],"note":"Taken from the CAD set's own floor, so that it moves with the F base's floor."},"slot_half":{"label":"The slot between the wings: half its width","kind":"length","measurements":[{"id":"model","value":0.156,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"planes x ±0.156 from the floor (y 2.3537) up to 2.4044, where the wings' inner arcs begin","via":"user"}}]},"wing_arc_above_seat":{"label":"The wings' arcs: their centre above the floor between the wings","kind":"length","measurements":[{"id":"model","value":0.0507,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"the arcs' axis at y 2.4044 against the floor's planes at y 2.3537","via":"user"}}]},"wing_arc_centre_half":{"label":"The wings' arcs: their centre out from the middle","kind":"length","measurements":[{"id":"model","value":0.8842,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"cylinders r 0.7282 and 0.6476 along z about (±0.8842, 2.4044)","via":"user"}}]},"wing_inner_r":{"label":"The wings' inner faces: their radius","kind":"length","measurements":[{"id":"model","value":0.7282,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"cylinders r 0.7282 about (±0.8842, 2.4044)","via":"user"}}]},"wing_outer_r":{"label":"The wings' outer faces: their radius","kind":"length","measurements":[{"id":"model","value":0.6476,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"cylinders r 0.6476 about (±0.8842, 2.4044)","via":"user"}}]},"wing_tip_above_seat":{"label":"The wings' tips above the floor between them","kind":"length","measurements":[{"id":"model","value":0.2176,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"the wings' highest vertices, y 2.5713, against the floor at 2.3537","via":"user"}}],"note":"The CAD set's base. In BCM's photo the wings' tips stand height_above_bore over the bore."},"swivel_ear_half":{"label":"The sling swivel's ears: half the width outside them","kind":"length","measurements":[{"id":"model","value":0.222,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"planes x ±0.222 (z -1.734 to -1.444, y -0.714 to -0.539)","via":"user"}}]},"swivel_gap_half":{"label":"The gap between the swivel's ears: half its width","kind":"length","measurements":[{"id":"model","value":0.1195,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"planes x ±0.1195 (z -1.798 to -1.395, y -0.714 to -0.500)","via":"user"}}]},"swivel_ear_from_rear":{"label":"The swivel's ears: their rear faces ahead of the rear face","kind":"length","measurements":[{"id":"model","value":0.04,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"planes z -1.764 against the rear face z -1.804","via":"user"}}]},"swivel_ear_length":{"label":"The swivel's ears: their length along the bore","kind":"length","measurements":[{"id":"model","value":0.35,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"planes z -1.764 to -1.414","via":"user"}}]},"swivel_hole_d":{"label":"The swivel's rivet hole, diameter","kind":"length","measurements":[{"id":"model","value":0.129,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"cylinders r 0.0645 along x through both ears","via":"user"}}],"note":"The Army's drawing has the same, .129 DIA THRU (8448566, side view)."},"swivel_hole_from_rear":{"label":"The swivel's rivet hole ahead of the rear face","kind":"length","measurements":[{"id":"model","value":0.215,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"its axis at z -1.589","via":"user"}},{"id":"photo","value":0.223,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/bcm-front-sight-base-f-750 e1fa9fe8e586 (Primary Arms Front-Sight-Base-F-750_01.jpg: BCM's base from its right side, straight on, the muzzle at the right, 2200 x 1467)","scaleRef":"frame from the reviewed holes pin, rear (365.7 px/in): the roll pin's hole and the rear face on its row, .688 apart (8448566)","method":"the see-through hole's centre, a circle through its rim's 50% crossings on 180 rays at (793.5, 1289.4), 39 px across (both ears' holes overlapping): 81.5 px ahead of the rear face (column 712)","via":"harvest"}}],"adopt":{"from":"photo","reason":"BCM's own base: its ear, in the side outline the model draws, is round about this hole. The CAD set's is 0.008 behind it, within the two readings' ±."}},"swivel_hole_below_bore":{"label":"The swivel's rivet hole below the bore","kind":"length","measurements":[{"id":"model","value":0.69,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"its axis at y -0.69","via":"user"}},{"id":"photo","value":0.653,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/bcm-front-sight-base-f-750 e1fa9fe8e586 (Primary Arms Front-Sight-Base-F-750_01.jpg: BCM's base from its right side, straight on, the muzzle at the right, 2200 x 1467)","scaleRef":"frame from the reviewed holes pin, rear (365.7 px/in): the roll pin's hole and the rear face on its row, .688 apart (8448566)","method":"the same centre, 467.3 px below the roll pin's hole, which is .625 above the bore (8448566)","via":"harvest"}}],"adopt":{"from":"photo","reason":"BCM's own base: its ear, in the side outline the model draws, is round about this hole (0.22 above its foot). The CAD set's hole and the Army's drawing's are 0.037 lower, on a .625 base's and a third-party model's ears: kept visible."},"note":"The Army's drawing gives .69 from the bore's centre line to the hole (8448566, side view)."},"swivel_ear_round_r":{"label":"The swivel's ears: the radius of their round foot about the hole","kind":"length","measurements":[{"id":"model","value":0.175,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"tori 0.145 + 0.03 about the axis (y -0.7137, z -1.589)","via":"user"}}]},"lug_stem_half":{"label":"The bayonet lug's stem: half its width","kind":"length","measurements":[{"id":"model","value":0.137,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"planes x ±0.137 (y -0.475 to -0.67, z -0.375 to 0.325)","via":"user"}}]},"lug_bar_half":{"label":"The bayonet lug's T: half its width","kind":"length","measurements":[{"id":"model","value":0.2215,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"planes x ±0.2215 (y -0.67 to -0.848)","via":"user"}}]},"lug_bar_top":{"label":"The bayonet lug's T: its top below the bore","kind":"length","measurements":[{"id":"model","value":0.67,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"planes y -0.67 (the stem's foot, the T's shoulders)","via":"user"}}]},"lug_from_front":{"label":"The bayonet lug's rear end behind the front face","kind":"length","measurements":[{"id":"model","value":0.375,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"plane z -0.375 (the lug's rear end under the front ring)","via":"user"}}]},"taper_pin_hole_d":{"label":"The taper pin's hole through the ring, diameter","kind":"length","measurements":[{"id":"model","value":0.141,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"a cylinder r 0.0705 along x through the rear ring","via":"user"}}],"note":"The Army's pin is .1419 at its big end (8448575)."},"taper_pin_from_rear":{"label":"The rear taper pin's hole ahead of the rear face","kind":"length","measurements":[{"id":"model","value":0.2065,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"its axis at z -1.5975","via":"user"}}],"note":"BCM's base comes undrilled (not yet drilled for taper pins): the holes are a gunsmith's, drilled through base and barrel. The CAD set has one, in the rear ring."},"taper_pin_below_bore":{"label":"The taper pins' holes below the bore","kind":"length","measurements":[{"id":"model","value":0.347,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"the rear pin's axis at y -0.3474: inside the journal's 0.375, so the pin crosses the barrel's underside","via":"user"}}]},"front_taper_pin_from_front":{"label":"The front taper pin's hole behind the front face","kind":"length","measurements":[{"id":"assumed","value":0.229,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the front ring's middle along its length (front_ring_length, 0.458, halved), at the rear pin's height. No drawing or photo on file shows a drilled base's front pin.","via":"harvest"}}],"note":"The CAD set draws one pin hole (the rear ring's); the front ring's is where no source on file says."},"taper_pin_length":{"label":"A taper pin's length","kind":"length","measurements":[{"id":"tdp","value":0.845,"unit":"in","pm":0.02,"stated":".845 ±.020","source":{"type":"standard","doc":"US Army TDP drawing 8448575 (Pin, Taper, Front Sight), rev H, PDF page 147","via":"user"}}]},"taper_pin_big_d":{"label":"A taper pin's large end, diameter","kind":"length","measurements":[{"id":"tdp","value":0.1419,"unit":"in","pm":0.0005,"stated":".1419 DIA REF","source":{"type":"standard","doc":"US Army TDP drawing 8448575 (Pin, Taper, Front Sight), rev H, PDF page 147","via":"user"}}]},"taper_pin_small_d":{"label":"A taper pin's small end, diameter","kind":"length","measurements":[{"id":"tdp","value":0.1251,"unit":"in","pm":0.0005,"stated":".1251 DIA REF","source":{"type":"standard","doc":"US Army TDP drawing 8448575 (Pin, Taper, Front Sight), rev H, PDF page 147","via":"user"}}]},"post_counterbore_d":{"label":"The post's counterbore at the tower's top, diameter","kind":"length","measurements":[{"id":"tdp","value":0.375,"unit":"in","pm":0.005,"stated":".375 +.005 C'BORE TO DEPTH SHOWN","source":{"type":"standard","doc":"US Army TDP drawing 8448566 (Sight, Front), rev H, PDF page 145, top view","via":"user"}}]},"post_counterbore_depth":{"label":"The post's counterbore: its floor below the tower's top","kind":"length","measurements":[{"id":"tdp","value":0.227,"unit":"in","pm":0.02,"stated":".227 ±.020","source":{"type":"standard","doc":"US Army TDP drawing 8448566 (Sight, Front), rev H, PDF page 145, side view's section through the tower","via":"user"}}],"note":"The drawing's section through the tower: the floor the post's flange sits on, where the thread begins."},"post_hole_d":{"label":"The post's threaded hole, its major diameter","kind":"length","measurements":[{"id":"tdp","value":0.164,"unit":"in","pm":0.002,"stated":"8-36 UNF-2B MODIFIED TO DEPTH SHOWN ... MAJOR DIA .1640 MIN","source":{"type":"standard","doc":"US Army TDP drawing 8448566 (Sight, Front), rev H, PDF page 145, top view","via":"user"}}]},"post_hole_depth":{"label":"The post's threaded hole, its depth from the tower's top","kind":"length","measurements":[{"id":"tdp","value":0.738,"unit":"in","pm":0.01,"stated":".738 ±.010","source":{"type":"standard","doc":"US Army TDP drawing 8448566 (Sight, Front), rev H, PDF page 145, side view's section through the tower","via":"user"}}]},"edge_break":{"label":"The break along its edges","kind":"length","measurements":[{"id":"tdp","value":0.01,"unit":"in","pm":0.005,"stated":"BREAK SHARP EDGES .005+.010 UNLESS OTHERWISE SPECIFIED","source":{"type":"standard","doc":"US Army TDP drawing 8448566 (Sight, Front), rev H, PDF page 145, note 6: the middle of .005 to .015","via":"user"}}]},"detent_hole_d":{"label":"The post's detent hole, diameter","kind":"length","measurements":[{"id":"tdp","value":0.171,"unit":"in","pm":0.003,"stated":".171 DIA +.003 TO DEPTH SHOWN","source":{"type":"standard","doc":"US Army TDP drawing 8448566 (Sight, Front), rev H, PDF page 145, top view: beside the post's hole, in the counterbore's floor","via":"user"}},{"id":"model","value":0.171,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"a cylinder r 0.0855 along y at z -0.151","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing; the CAD set has the same."}},"detent_ahead_of_post":{"label":"The detent hole's axis ahead of the post's","kind":"length","measurements":[{"id":"tdp","value":0.203,"unit":"in","pm":0.002,"stated":".203 ±.002","source":{"type":"standard","doc":"US Army TDP drawing 8448566 (Sight, Front), rev H, PDF page 145, side view: the post's axis to the detent hole's","via":"user"}},{"id":"model","value":0.203,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"the detent hole's axis at z -0.151 against the post's at z -0.354: ahead of it, toward the muzzle","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing; the CAD set has it at the same place, and says which way (toward the muzzle)."},"note":"Under the post's flange: the detent rides on the .400 circle the flange's notches are on (9349056)."},"detent_hole_depth":{"label":"The detent hole's depth below the counterbore's floor","kind":"length","measurements":[{"id":"model","value":0.511,"unit":"in","pm":0.01,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Front_Sight.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a .750 front sight base)","method":"the hole from y 1.6158 up to the counterbore's floor (its .375 cylinder's foot, y 2.1267)","via":"user"},"note":"The drawing's \"TO DEPTH SHOWN\" is drawn, not dimensioned."}]}}},{"subject":"bcm-gi-barrel-nut","title":"BCM G.I. Barrel Nut - AR15","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"metal","value":1.37,"unit":"oz","pm":0.1,"source":{"type":"derived","expr":"(0.785398163 * ({std.ar15.barrel_nut_body_od} * {std.ar15.barrel_nut_body_od} * {std.ar15.barrel_nut_flange_rear} + {std.ar15.barrel_nut_flange_od} * {std.ar15.barrel_nut_flange_od} * ({std.ar15.barrel_nut_length} - {std.ar15.barrel_nut_flange_rear}) - ({std.ar15.barrel_nut_thread_major_d} + {std.ar15.barrel_nut_thread_minor_d}) * ({std.ar15.barrel_nut_thread_major_d} + {std.ar15.barrel_nut_thread_minor_d}) / 4 * {std.ar15.barrel_nut_thread_length} - {std.ar15.barrel_nut_counterbore_d} * {std.ar15.barrel_nut_counterbore_d} * ({std.ar15.barrel_nut_shoulder} - {std.ar15.barrel_nut_thread_length}) - {std.ar15.barrel_nut_bore_d} * {std.ar15.barrel_nut_bore_d} * ({std.ar15.barrel_nut_length} - {std.ar15.barrel_nut_shoulder} - {std.ar15.barrel_nut_front_recess}) - {std.ar15.barrel_nut_counterbore_d} * {std.ar15.barrel_nut_counterbore_d} * {std.ar15.barrel_nut_front_recess} - ({std.ar15.barrel_nut_body_od} * {std.ar15.barrel_nut_body_od} - {std.ar15.barrel_nut_groove_d} * {std.ar15.barrel_nut_groove_d}) * {std.ar15.barrel_nut_groove_width}) - {std.ar15.barrel_nut_notches} * 0.392699082 * {std.ar15.barrel_nut_notch_d} * {std.ar15.barrel_nut_notch_d} * ({std.ar15.barrel_nut_length} - {std.ar15.barrel_nut_flange_rear})) * {std.density.steel}","via":"harvest"}}],"note":"No maker's or seller's figure: BCM states none (its page's markup has \"weight\":null). Worked out from the mil-spec nut's sizes as steel: its body and flange turned, less its thread's bore at the thread's mean diameter, the counterbore, the barrel's bore, the front recess, the snap ring's groove and its twenty notches (each taken as half a round). A derived figure, for the build's total; the model's own volume is held to it in app/tests/bcm-gi-barrel-nut.test.ts."},"length":{"label":"Length along the bore","kind":"length","measurements":[{"id":"standard","value":0.85,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.ar15.barrel_nut_length}","via":"harvest"}}],"note":"BCM states none. The mil-spec nut's: BCM calls this one the G.I. nut, and its photo has the mil-spec nut's proportions (its flange's teeth a seventh of its length, the groove near its rear end; not measured: the photo is an oblique from above, 830 px)."},"flange_diameter":{"label":"Its toothed flange's outside diameter","kind":"length","measurements":[{"id":"standard","value":1.56,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{std.ar15.barrel_nut_flange_od}","via":"harvest"},"note":"The mil-spec nut's; BCM states none."}]},"notches":{"label":"The notches round its flange","kind":"count","measurements":[{"id":"standard","value":20,"unit":"count","pm":0,"source":{"type":"derived","expr":"{std.ar15.barrel_nut_notches}","via":"harvest"}}],"note":"Not counted on BCM's photo: it is an oblique from above (830 px) with notches all round the flange's rim, but the teeth at the back are foreshortened into each other. The mil-spec nut's twenty, the gas tube in the one at the top."}}},{"subject":"bcm-grip-mod-3","title":"BCM Grip Mod 3 (BCM-GFG-Mod-3-BLK)","dimensions":{"grip_angle":{"label":"Grip angle (the straps' lean from vertical, installed)","kind":"angle","measurements":[{"id":"flat-top-fde3","value":19.59,"unit":"deg","pm":0.44,"source":{"type":"photo","photo":"references/bcm-grip-mod-3 bdf41efeff9d (BCM's Mod_3_FDE_3: the FDE grip lying on its right side on white with its screw, straight left side, 3700 x 2467)","scaleRef":"none needed: an angle within one outline","method":"the outline (luminance < 225) turned 15.33 degrees so that a line through its flat top (the top edge from 0.13 to 0.98 in ahead of the flat's rear end, 394 columns, rms 0.66 px) is level; then the mean lean of its edges in the band 0.45-0.85 of its height (rear 21.42, front 17.76: tools/trace.py edge_lean). ± is 1.5 px at each end of the fitted run.","via":"harvest"}},{"id":"flat-top-fde4","value":20.02,"unit":"deg","pm":0.93,"source":{"type":"photo","photo":"references/bcm-grip-mod-3 677abc5611a5 (BCM's Mod_3_FDE_4: the FDE grip cut out on white, straight right side, 1280 x 1280)","scaleRef":"none needed: an angle within one outline","method":"as flat-top-fde3 (turned 15.76 degrees; the flat top's line over 185 columns, rms 0.30 px; rear 21.83, front 18.20)","via":"harvest"}},{"id":"flat-top-pa-left","value":19.85,"unit":"deg","pm":0.78,"source":{"type":"photo","photo":"references/bcm-grip-mod-3 efa47b5d7a2d (Primary Arms BCM-GFG-MOD-3-BLACK_00: the black grip on white, straight left side, 2200 x 1466)","scaleRef":"none needed: an angle within one outline","method":"as flat-top-fde3 (the photo has the flat top level already: turned 0.11 degrees; the line over 220 columns, rms 0.28 px; rear 21.62, front 18.09)","via":"harvest"}},{"id":"flat-top-pa-right","value":20.79,"unit":"deg","pm":0.78,"source":{"type":"photo","photo":"references/bcm-grip-mod-3 b35d98994e45 (Primary Arms BCM-GFG-MOD-3-BLACK_01: the black grip on white, straight right side, 2200 x 1466)","scaleRef":"none needed: an angle within one outline","method":"as flat-top-fde3 (turned 1.12 degrees; the line over 220 columns, rms 0.43 px; rear 22.42, front 19.17)","via":"harvest"}},{"id":"flat-top-review","value":20.2,"unit":"deg","pm":1.34,"source":{"type":"photo","photo":"references/bcm-grip-mod-3 65a384e723b0 (Santomieri's BCM-Grip-Mod3-07: the black grip lying on white, straight left side, 1200 x 797)","scaleRef":"none needed: an angle within one outline","method":"as flat-top-fde3 (turned 13.54 degrees; the line over 128 columns, rms 0.27 px; rear 22.11, front 18.29)","via":"harvest"}},{"id":"aggregator","value":17,"unit":"deg","pm":0.5,"stated":"Grip Angle : ~17 degrees","source":{"type":"spec","publisher":"review","name":"Rifle Configurator, \"Best AR-15 Pistol Grips 2026\" (a ranking with affiliate links; no method given)","url":"https://www.rifleconfigurator.com/guides/best-ar15-pistol-grips-2026","retrieved":"2026-10-05","via":"harvest"},"note":"The only page that puts a number on it, and it says nothing of how (the same page files the grip under \"17 degrees (modern default) ... Picks: Magpul K2+, K2, BCM Mod 3\"). Kept in view, not used."}],"adopt":{"from":"flat-top-fde3","reason":"Installed, the flat top lies on the receiver's level underside, so the straps lean as they do from that face: an angle inside one outline, here the maker's own largest photo, which the side outline is traced from (so its flat top comes out level). Four other photos read the same within their ± (19.85 to 20.79). The ranking page's ~17 has no method behind it."},"note":"The mean of the back and front straps' lean (the band 0.45 to 0.85 of the outline's height) with the flat top, which bears on the receiver's underside, level. BCM gives no figure: \"Reduced angle for improved ergonomics and trigger control\". Six side photos by three photographers, each turned until a line through its own flat top is level, read 19.6 to 20.8 (mean 20.1; .cache/batch123/bcm-grip-mod-3/flat_top_lean.py); the back strap leans about 21.6, the front strap 18.2."},"review_height":{"label":"\"Overall Height\" (the review's own measurement)","kind":"length","measurements":[{"id":"review","value":4.242,"unit":"in","stated":"Overall Height * 4.242 in (107.76 mm) [...] * - Overall height measured from where the grip meets the lower to the bottom of the grip.","source":{"type":"spec","publisher":"review","name":"Josh Santomieri, \"BCM Gunfighter Grip - Mod 3\" (Santomieri Systems, 2014-05-06; the same text ran at The Truth About Guns): Specifications & Measurements, the BCM Mod 3 column","url":"https://www.santsys.com/s2blog/bcm-gunfighter-grip-mod-3","retrieved":"2026-10-05","via":"harvest"}}],"note":"Taken as the drop square to the flat top: from the face that bears on the receiver's underside to the grip's lowest point, its toe (a caliper's jaw laid on the flat top, the other on the toe). No photo of this grip on a lower with its pins in view has been read to check it (the one that was, Wing Tactical's for BCM's stock, turned out to show a Mod 0 grip). What holds it: at this scale the side outline is 1.905 in front to back where the same table says 1.918 (depth), and the Magpul MOE in the same table reads 4.069 in (103.36 mm), where Magpul's \"Height, receiver to bottom\" is 4.0 and Aero's photo of one installed 4.03 (magpul-moe-plus.bottom_below_lower_underside): his readings of this span run about 1% over."},"bottom_below_lower_underside":{"label":"Grip bottom below the receiver's underside where the grip bears","kind":"length","measurements":[{"id":"review","value":4.242,"unit":"in","source":{"type":"derived","expr":"{.review_height}","via":"harvest"},"note":"The review's \"Overall Height\", taken as from the face the grip's flat top bears on to its lowest point (review_height says why)."},{"id":"lineup","value":4.145,"unit":"in","pm":0.07,"source":{"type":"photo","photo":"references/bcm-grip-mod-3 ed106200b280 (Santomieri's BCM-Grip-Mod3-02: the Mod 3 and a Magpul MOE lying on their left sides, side by side, 1200 x 797)","scaleRef":"the MOE beside it, by Magpul's \"Height, receiver to bottom 4.0 in.\" (magpul-moe-plus.bottom_below_lower_underside: the catalog's MOE+ side outline, the plain MOE's shape, fitted to its silhouette at 136.5 px per inch, rms 4.7 px)","method":"this grip's traced side outline fitted to its silhouette in the same photo (rotation, translation and scale; the worst-fitting fifth of each silhouette, the open doors, left out): 133.3 px per inch of an outline drawn at 4.242, rms 1.9 px. The two scales are 0.9764 apart (0.9762 to 0.9784 at three thresholds): 4.242 x 0.9764. ± is the MOE's fit (a plain MOE against the MOE+'s outline) and Magpul's last digit. (.cache/batch123/bcm-grip-mod-3/lineup.py)","via":"harvest"},"note":"The same reviewer's calipers have the two grips 4.242 and 4.069: 1.043 apart, where this photo has them 1.036 apart. So the photo bears out his ratio, and the 2% is his reading of the MOE over Magpul's own figure for it (4.069 against 4.0; Aero's photo of one installed, 4.03)."}],"adopt":{"from":"review","reason":"The one figure taken on this grip itself, with calipers. His photo of it beside a Magpul MOE has the two in the ratio his calipers give (1.036 against 1.043), so the question is what an MOE's own drop is: by Magpul's 4.0 this grip is 4.145, by his calipers' 4.069 it is 4.242. The model may be 2% large; that stays in view here until a Mod 3 is read on a lower with its pins in view."},"note":"What the side photo is scaled by: the grip frame's origin (the rear end of its flat top) down to its toe."},"depth":{"label":"Front to back at the thickest portion of the hand grip, square to the straps (the review's \"Width\")","kind":"length","measurements":[{"id":"review","value":1.918,"unit":"in","stated":"Width *** 1.918 in (48.71 mm) [...] *** - Width measured at the thickest portion of the actual hand grip area.","source":{"type":"spec","publisher":"review","name":"Josh Santomieri, \"BCM Gunfighter Grip - Mod 3\" (Santomieri Systems, 2014-05-06; the same text ran at The Truth About Guns): Specifications & Measurements, the BCM Mod 3 column","url":"https://www.santsys.com/s2blog/bcm-gunfighter-grip-mod-3","retrieved":"2026-10-05","via":"harvest"}},{"id":"photo","value":1.905,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-grip-mod-3 bdf41efeff9d (BCM's Mod_3_FDE_3: the FDE grip lying on its right side on white, straight left side, 3700 x 2467)","scaleRef":"the 4.242 in drop (bcm-grip-mod-3.bottom_below_lower_underside): 464.3 px/in","method":"the traced outline turned so the straps' mean lean is upright; its front-to-back width row by row: 2.08 at the foot's flare, 1.905 just above it (0.55 to 0.65 in above the base), narrowing to 1.65 under the tang (.cache/batch123/bcm-grip-mod-3/width_profile.py; app/tests/bcm-grip-mod-3.test.ts reads it again off the stored outline). ± is the edges (1.5 px each) and where above the flare the widest row is taken.","via":"harvest"}}],"adopt":{"from":"review","reason":"The measured figure. The side outline, scaled by the same table's height, is 0.7% under it at the same place: the two figures hold together in one view. Nothing is drawn from this value."},"note":"Above the foot's flare: the foot itself is 2.1 to 2.3 in front to back. The Magpul MOE in the same table reads 1.979 in (50.27 mm)."},"thickness":{"label":"Thickness (side to side)","kind":"length","measurements":[{"id":"review","value":1.236,"unit":"in","stated":"Thickness ** 1.236 in (31.39 mm) [...] ** - Thickness measured at the thickest portion of the grip.","source":{"type":"spec","publisher":"review","name":"Josh Santomieri, \"BCM Gunfighter Grip - Mod 3\" (Santomieri Systems, 2014-05-06; the same text ran at The Truth About Guns): Specifications & Measurements, the BCM Mod 3 column","url":"https://www.santsys.com/s2blog/bcm-gunfighter-grip-mod-3","retrieved":"2026-10-05","via":"harvest"},"note":"The Magpul MOE in the same table reads 1.205 in (30.60 mm), where Magpul says \"Thickness, max 1.2 in.\""},{"id":"aggregator","value":1.4,"unit":"in","pm":0.05,"stated":"Width : 1.4 inches (0.25\" wider than Mod 0/1)","source":{"type":"spec","publisher":"review","name":"Rifle Configurator, \"Best AR-15 Pistol Grips 2026\" (a ranking with affiliate links; no method given)","url":"https://www.rifleconfigurator.com/guides/best-ar15-pistol-grips-2026","retrieved":"2026-10-05","via":"harvest"},"note":"No method, and it may be the foot's (foot_width)."}],"adopt":{"from":"review","reason":"A measured figure with its footnote, against a ranking page's round one. In the reviewer's own photo of the grip from behind, beside a Magpul MOE, the body is this wide where the MOE is Magpul's 1.2 (profiles.rear)."},"note":"The hand grip's, where the review's calipers took it. BCM: \"Up to a quarter of an inch wider than the BCM® Mod 0 and Mod 1 grips.\""},"seat_x":{"label":"Seat, X: where the grip's frame origin (its flat top's rear end) sits ahead of the takedown pin, installed","kind":"length","measurements":[{"id":"interface","value":-0.094,"unit":"in","source":{"type":"derived","expr":"{std.ar15.receiver_rear_x} + {std.ar15.grip_lug_front_from_rear_face} - {.block_front_x}","via":"harvest"},"note":"The block's front face (block_front_x, on the traced side) at the ears' rear face. If the ledge at the slot's mouth is what meets the ears, 0.017 further back."}],"note":"A grip's own figure on the standard AR-15 grip mount (D19, D28). Seated by its interface: the top block's front face against the rear face of the trigger guard's ears, where the Army drawing ends the lug (2.300 from the receiver's rear face, 1.175 ahead of the takedown pin). That is how a BCM grip of this family sits in the one pin-framed photo on file (Wing Tactical's for the Mod 0 stock, a Mod 0 grip: its block's front face reads 1.176 ± 0.01 ahead of the pin, its top on the standard's seat at -1.065). The slot's rear wall then falls at the flat top's rear end, as the photos of the top show it, and the ledge at the slot's mouth is 0.93 below the top, the standard lug's depth. Until 01:45 on 2026-10-05 this was -0.019 ± 0.041, the outline fitted into that photo: a fit to another grip's straps."},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"review","value":3.2,"unit":"oz","stated":"Weight 3.2 oz","source":{"type":"spec","publisher":"review","name":"Josh Santomieri, \"BCM Gunfighter Grip - Mod 3\" (Santomieri Systems, 2014-05-06; the same text ran at The Truth About Guns): Specifications & Measurements, the BCM Mod 3 column","url":"https://www.santsys.com/s2blog/bcm-gunfighter-grip-mod-3","retrieved":"2026-10-05","via":"harvest"},"note":"The scale isn't named, nor whether the screw and lock washer were on it."},{"id":"dirty-bird","value":3.408,"unit":"oz","stated":"Weight 3.408 oz","source":{"type":"spec","publisher":"retailer","name":"Dirty Bird Industries, BCMGUNFIGHTER Pistol Grip - MOD 3: Additional information (one page for four colours)","url":"https://dirtybirdusa.com/products/bcmgunfighter-pistol-grip-mod-3/","retrieved":"2026-10-05","via":"harvest"},"note":"0.213 lb in the seller's own records; where it comes from isn't said."},{"id":"wing","value":3.64,"unit":"oz","stated":"Weight: 3.64 oz.","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Bravo Company BCMGUNFIGHTER Pistol Grip - Mod 3: Specifications (\"Includes: 1x Bravo Company BCMGUNFIGHTER Pistol Grip - Mod 3 1x Pistol Grip Screw 1x Washer\")","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/grips-foregrips/pistol-grips/bravo-company-bcmgunfighter-pistol-grip-mod-3/","retrieved":"2026-10-05","via":"harvest"}}],"adopt":{"from":"dirty-bird","reason":"The grip as it goes on a rifle, with its screw and lock washer, as the catalog's other grips are weighed (Magpul's \"w/ hardware\"). The review's 3.2 oz is the one figure anyone says they weighed, and its table reads 0.2 oz under Magpul's with-hardware figure for the MOE beside it: the same 0.2 oz over 3.2 is this seller's 3.4. Wing Tactical's 3.64 stands alone. None is BCM's, and all three stay in view."},"note":"BCM states none. KYGunCo's page says \"Weight 2 lb\", the same on its pages for a trigger and a stock: a shipping default, left out. The review's table reads 0.2 oz under Magpul's own figure for the MOE beside it (2.6 against \"Weight, w/ hardware 2.8 oz.\"): its weights look like the grips without their screw and washer."},"overall_height":{"label":"Overall height in the grip frame (the beavertail's top to the toe)","kind":"length","measurements":[{"id":"photo","value":4.957,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/bcm-grip-mod-3 bdf41efeff9d (BCM's Mod_3_FDE_3: the FDE grip lying on its right side on white, straight left side, 3700 x 2467)","scaleRef":"scale from bcm-grip-mod-3.bottom_below_lower_underside = 4.242 in (y from the origin to the far edge 1970 px → 464.3 px/in)","method":"height of the traced outline (tools/trace.py); the traced outline's height, the beavertail's top to the toe","via":"harvest"}}]},"block_front_x":{"label":"Top block's front face, ahead of the flat top's rear end","kind":"length","measurements":[{"id":"photo","value":1.269,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-grip-mod-3 bdf41efeff9d (BCM's Mod_3_FDE_3: the FDE grip lying on its right side on white, straight left side, 3700 x 2467)","scaleRef":"scale from bcm-grip-mod-3.bottom_below_lower_underside = 4.242 in (y from the origin to the far edge 1970 px → 464.3 px/in)","method":"x_max in y [-0.85, -0.25] of the traced outline (tools/trace.py); the top block's front face ahead of the flat top's rear end, between the corner above it and the ledge at the slot's mouth below (which stands 0.017 further out, 0.93 below the top)","via":"harvest"}}]},"toe_y":{"label":"Toe (the grip's lowest point), Y in the grip frame","kind":"length","measurements":[{"id":"derived","value":-4.242,"unit":"in","source":{"type":"derived","expr":"-{.bottom_below_lower_underside}","via":"harvest"}}]},"top_block_width":{"label":"Top block (the two walls that sit under the receiver), across","kind":"length","measurements":[{"id":"flush","value":0.88,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-grip-mod-3 aff838e7b1c6 (BCM's BCM-GFG-Mod-3-BLK-5: a BCM lower with the grip, from ahead and the left, 1200 x 800)","scaleRef":"the receiver's own width where the grip meets it: the standard's 0.88 in body (std.ar15.lower_body_width)","method":"the block's side face runs on into the receiver's with no step at the seam, on the side the photo shows: taken as the receiver's width. ± is a step of 0.02 in a side, which wouldn't show at this size.","via":"harvest"}}],"note":"No page gives it and no photo is square to it. The army's A2 grip is .885 across its top (aero-m4e1-lower.grip_body_width, drawing 9349127). The beavertail's neck reads this wide in the review's view from behind (profiles.rear)."},"foot_width":{"label":"Foot (the flare at the base), across: the widest the grip is, side to side","kind":"length","measurements":[{"id":"rear-photo","value":1.36,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/bcm-grip-mod-3 7192cb9b2d04 (Santomieri's BCM-Grip-Mod3-03: the Mod 3 lying on its front strap, its back strap straight on from above, a Magpul MOE beside it, 1200 x 797)","scaleRef":"scale from bcm-grip-mod-3.thickness = 1.236 in (median width over 0.34–0.46 of the height from the top, 149–151 px 150 px → 121.4 px/in)","method":"width of the traced outline (tools/trace.py); the outline's widest row, at the foot, at the scale the review's 1.236 in gives the upper body (rows 225 to 297, 149 to 151 px): at that scale the Magpul MOE lying beside it (its body 145 px across at the same threshold, 143 to 146) is 1.195 in, Magpul's 1.2. ± is the lens: the photo is taken from close, and what stands higher over the table reads larger","via":"harvest"}}],"note":"From the one view from behind, a close photo: read as photographed. A ranking page's \"Width : 1.4 inches\" (thickness, aggregator) may be this."},"rib_reach":{"label":"Front strap's ribs: how far back from the strap's edge they run, in the side view","kind":"length","measurements":[{"id":"photo","value":0.138,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bcm-grip-mod-3 bdf41efeff9d (BCM's Mod_3_FDE_3: the FDE grip lying on its right side on white, straight left side, 3700 x 2467)","scaleRef":"the 4.242 in drop (bcm-grip-mod-3.bottom_below_lower_underside): 464.3 px/in","method":"read on a gridded 4x crop at rows 1250 to 1500, where the front strap stands 2.4 degrees off the photo's vertical: the ribs' crests at column 1359, their rear ends at 1420 to 1426: 64 px. ± is 6 px.","via":"harvest"}}],"note":"The ribs are about 0.047 in apart (22 px) and stand 0.012 in out of the strap's edge. Behind their ends a smooth band runs to the texture panel's front border, 0.224 in (104 px) behind the edge."},"lug_slot_width":{"label":"The slot in the top that goes over the receiver's lug, across","kind":"length","measurements":[{"id":"pa-right","value":0.374,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-grip-mod-3 81f1933f5008 (Primary Arms BCM-GFG-MOD-3-BLACK_02: the black grip from ahead and the right, 2200 x 1466)","scaleRef":"the block's own width across the same face (bcm-grip-mod-3.top_block_width, 0.88 ± 0.04)","method":"on 11 rows across the block's front face (rows 400 to 500, a 5-row mean each): the face's far edge (the silhouette), the slot's two walls (half-way between the lit face and the slot's dark) and the near corner (the chamfer's bright line). The slot is 45.5 px of 106.8: 0.4249 of the face (0.4223 to 0.4290 over the rows). ± is the block's width and 2 px on the corner. (.cache/batch123/bcm-grip-mod-3/slot_front.py)","via":"harvest"}},{"id":"pa-left","value":0.373,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-grip-mod-3 06abf4e70ab1 (Primary Arms BCM-GFG-MOD-3-BLACK_03: the black grip from ahead and the left, 2200 x 1467)","scaleRef":"the block's own width across the same face (bcm-grip-mod-3.top_block_width, 0.88 ± 0.04)","method":"as pa-right, from the other side (the near corner is the chamfer's dark line here): the slot is 57.3 px of 135.3, 0.4239 of the face (0.4111 to 0.4354: it reads 3 px wider on the lower rows than the upper). (.cache/batch123/bcm-grip-mod-3/slot_front.py)","via":"harvest"}}],"adopt":{"value":0.385,"unit":"in","pm":0.01,"reason":"The slot goes over the receiver's lug, so it isn't under the lug's .375; the two readings, 0.374 and 0.373 ± 0.02, put it at 0.394 at most. The middle of what both leave, ± half of it: 0.005 in clear of the lug on each side, where the MOE-K2+'s slot is 0.025 clear. Stands until a view square to the top, with a scale, is read."},"note":"No view on file is square to the grip's top (the two from above, Wing Tactical's, are close and oblique, and the top face's edges can't be told apart in them). The slot is cut through the block's front face, and two photos see that face, one from each side: its two walls and the face's two outer corners are four lines in one plane, so their spacing along a row needs no scale. The slot is 0.4249 and 0.4239 of the face: at the block's 0.88 in, the lug's own .375 (std.ar15.grip_lug_width). A fit as tight as these photos can tell; the review: \"These grips are often a tight fit on the lower, so you may have to give it a good push to get it on to the lower\"."}}},{"subject":"bcm-grip-mod-4","title":"BCM Grip Mod 4 (BCM-GFG-MOD-4-BLK)","dimensions":{"toe_below_pin":{"label":"The grip's lowest point (its toe) below the takedown pin, installed","kind":"length","measurements":[{"id":"installed","value":5.248,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 842fbe8fe0ba (Primary Arms LRG-RMS-NO-STOCK_01: BCM's MK2 lower without stock, its right side square on white, the Mod 4 grip on it, 2200 x 1467)","scaleRef":"the lower's own pins and holes at the Army drawing's places (std.ar15.pin_spacing, selector, trigger and hammer pins, the guard's two holes: 134.1 px/in, the worst miss 0.045 in; the lower's owner's frame)","method":"the grip's silhouette below the guard (luminance < 200, inside [940, 830, 1300, 1260], the largest piece, closed ×2): its lowest point, −5.248 (tools/trace.py, spec installed). ± is the frame's 0.5% over 5.2 in and the edge's 2 px.","via":"harvest"}}],"note":"Read in a frame of the lower's pins, where the grip stands against the white below the trigger guard. The frame is set at the receiver's right face (the pins' heads and the drawing's holes): the grip's silhouette is its own widest, at about the same depth from the lens, so it reads at about the frame's scale."},"bottom_below_lower_underside":{"label":"Grip bottom below the receiver's underside where the grip bears","kind":"length","measurements":[{"id":"installed","value":4.179,"unit":"in","source":{"type":"derived","expr":"{.toe_below_pin} + {std.ar15.deck_y} - {std.ar15.grip_seat_below_deck}","via":"harvest"},"note":"The toe read in the pin-framed photo of the grip installed, less the seat's depth below the pin line by the Army drawing (1.318 below the deck, which is .2485 above the pin)."}],"note":"What the side photo is scaled by: from the grip's flat top, which bears on the receiver's underside under the lug (std.ar15.grip_seat_below_deck below the deck, the deck std.ar15.deck_y above the pin), to its toe."},"grip_angle":{"label":"Grip angle (the straps' lean from vertical, installed)","kind":"angle","measurements":[{"id":"installed-straps","value":17.4,"unit":"deg","pm":1.6,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 842fbe8fe0ba (Primary Arms LRG-RMS-NO-STOCK_01: BCM's MK2 lower without stock, its right side square on white, the Mod 4 grip on it, 2200 x 1467)","scaleRef":"none needed for an angle: the frame of the lower's pins sets the level","method":"a straight line through the grip's silhouette along each strap, 2.9 to 4.3 in below the pin: the back strap 19.35 ± 1.1 degrees from the vertical (1.48 in of it, rms 0.009), the front strap 15.41 ± 2.8 (0.54 in of it between its ribs, rms 0.007); their mean. ± is half the two straps' difference with the shorter run's own (tools/trace.py line_lean, spec installed).","via":"harvest"}},{"id":"flat-top-pa","value":17.4,"unit":"deg","pm":0.5,"source":{"type":"photo","photo":"references/bcm-grip-mod-4 87b3693f2d0e (Primary Arms BCM-GFG-MOD-4-BLK_01: the black grip on white, straight right side, 2200 x 1467)","scaleRef":"none needed: an angle within one outline","method":"the side outline (luminance < 200) turned so that its straps' mean lean in the band 0.45-0.85 of its height is 17.4 (rear 19.4, front 15.4): its flat top, from its rear end to the block's front corner (1.08 in, 11 outline points), then lies level to within 0.01 in, 0.3 degrees: the grip's flat top level is this lean. ± is that and the edges' 1.5 px over the band.","via":"harvest"}},{"id":"installed-fit","value":15.6,"unit":"deg","pm":1.1,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 842fbe8fe0ba (Primary Arms LRG-RMS-NO-STOCK_01: BCM's MK2 lower without stock, its right side square on white, the Mod 4 grip on it, 2200 x 1467)","scaleRef":"the side outline at its own scale (the drop it is scaled by is read in this photo)","method":"the side outline fitted into the grip's silhouette below the guard (2.6 in of it, the straps and the foot; 1150 edge points, rms 0.046 in), turned and moved, scale fixed: it turns 2.0 degrees more upright; the fitted outline's straps lean 17.6 and 13.7 (tools/trace.py registered_lean, spec installed-fit). Free in scale it fits at 0.970 and turns 2.6 degrees.","via":"harvest"},"note":"Kept in view: the fit sees only the lower half of the grip, whose foot (seen from above its base: the open bottom's rim shows) it weighs as much as the straps."}],"adopt":{"from":"flat-top-pa","reason":"Installed, the flat top lies on the receiver's level underside, so the straps lean as they do from that face: an angle inside one outline, the photo the side outline is traced from. The straight lines along the two straps in the pin-framed photo of the grip installed read the same (17.4). The fit of the outline's lower half into that photo turns it 2 degrees further (15.6 ± 1.1): it weighs the foot, seen from above, as much as the straps, and its rms (0.046 in) is four times the straps' lines'."},"note":"The mean of the back and front straps' lean (the band 0.45 to 0.85 of the outline's height) with the flat top, which bears on the receiver's underside, level. BCM gives no figure: \"Reduced angle for improved ergonomics and trigger control\". The back strap leans about 19.4, the front strap 15.4."},"overall_height":{"label":"Overall height in the grip frame (the beavertail's top to the toe)","kind":"length","measurements":[{"id":"photo","value":4.846,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/bcm-grip-mod-4 87b3693f2d0e (Primary Arms BCM-GFG-MOD-4-BLK_01: the black grip on white, straight right side, 2200 x 1467)","scaleRef":"scale from bcm-grip-mod-4.bottom_below_lower_underside = 4.179 in (y from the origin to the far edge 1090 px → 260.9 px/in)","method":"height of the traced outline (tools/trace.py); the traced outline's height, the beavertail's top to the toe","via":"harvest"}}]},"block_front_x":{"label":"Top block's front face, ahead of the flat top's rear end","kind":"length","measurements":[{"id":"photo","value":1.265,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bcm-grip-mod-4 87b3693f2d0e (Primary Arms BCM-GFG-MOD-4-BLK_01: the black grip on white, straight right side, 2200 x 1467)","scaleRef":"scale from bcm-grip-mod-4.bottom_below_lower_underside = 4.179 in (y from the origin to the far edge 1090 px → 260.9 px/in)","method":"x_max in y [-0.85, -0.25] of the traced outline (tools/trace.py); the top block's front face ahead of the flat top's rear end, between the corner above it and the tang below","via":"harvest"}}]},"seat_x":{"label":"Seat, X: where the grip's frame origin (its flat top's rear end) sits ahead of the takedown pin, installed","kind":"length","measurements":[{"id":"interface","value":-0.09,"unit":"in","source":{"type":"derived","expr":"{std.ar15.receiver_rear_x} + {std.ar15.grip_lug_front_from_rear_face} - {.block_front_x}","via":"harvest"},"note":"The block's front face (block_front_x, on the traced side) at the ears' rear face."},{"id":"installed-fit","value":-0.24,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 842fbe8fe0ba (Primary Arms LRG-RMS-NO-STOCK_01: BCM's MK2 lower without stock, its right side square on white, the Mod 4 grip on it, 2200 x 1467)","scaleRef":"the lower's pins at the Army drawing's places (134.1 px/in)","method":"where the side outline's origin lands when its lower half is fitted into the grip's silhouette below the guard (scale fixed; rms 0.046 in): x -0.240, y -1.052 (the seat by the drawing is -1.0695). The fit turns the outline 2.0 degrees, which moves an origin 4 in above the fitted part by 0.14 in (tools/trace.py registered_x, spec installed-fit).","via":"harvest"},"note":"Kept in view: a fit 4 in below the seat it reads, turned by the angle the flat top says it isn't."}],"adopt":{"from":"interface","reason":"The block's front face bears on the ears' rear face, where the Army drawing ends the lug: the interface seats it. The fit's origin is 4 in above what it fits, and it turns the outline 2 degrees off its flat top: at the flat top's angle the fit's own rotation, 2.0 degrees about the foot, accounts for 0.14 of its 0.15 in."},"note":"A grip's own figure on the standard AR-15 grip mount (D19, D28). Seated by its interface, as BCM's Mod 3 is: the top block's front face against the rear face of the trigger guard's ears, where the Army drawing ends the lug (2.300 from the receiver's rear face, 1.175 ahead of the takedown pin)."},"thickness":{"label":"Thickness (side to side), across the hand grip's body","kind":"length","measurements":[{"id":"front-photo","value":1.239,"unit":"in","pm":0.061,"source":{"type":"photo","photo":"references/bcm-grip-mod-4 d736daca7a02 (BCM's BCM-MOD-4-GRIP-BLK-2: the black grip from ahead, its front strap straight on, from a little above, cut out on white, 1000 x 1000)","scaleRef":"scale from bcm-grip-mod-4.top_block_width = 0.88 in (median width over 0.08–0.19 of the height from the top, 119–123 px 119 px → 135.2 px/in)","method":"median row width in y [-3.6, -1.6] (1.214–1.272) of the traced outline (tools/trace.py); the median row width of the hand grip's body (rows 388 to 663 of 1000), at the scale the block's two walls give the top (rows 230 to 300, 119 to 122 px across for 0.88 in)","via":"harvest"}}]},"foot_width":{"label":"Foot (the flare at the base), across: the widest the grip is, side to side","kind":"length","measurements":[{"id":"front-photo","value":1.279,"unit":"in","pm":0.062,"source":{"type":"photo","photo":"references/bcm-grip-mod-4 d736daca7a02 (BCM's BCM-MOD-4-GRIP-BLK-2: the black grip from ahead, its front strap straight on, from a little above, cut out on white, 1000 x 1000)","scaleRef":"scale from bcm-grip-mod-4.top_block_width = 0.88 in (median width over 0.08–0.19 of the height from the top, 119–123 px 119 px → 135.2 px/in)","method":"width of the traced outline (tools/trace.py); the outline's widest row, at the foot's flare, at the scale the block's walls give the top","via":"harvest"}}]},"top_block_width":{"label":"Top block (the two walls that sit under the receiver), across","kind":"length","measurements":[{"id":"flush","value":0.88,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 842fbe8fe0ba (Primary Arms LRG-RMS-NO-STOCK_01: the MK2 lower with this grip, right side) and d872250eaa9b (its blem, from ahead of the right side and above)","scaleRef":"the receiver's own width where the grip meets it: the standard's 0.88 in body (std.ar15.lower_body_width)","method":"the block's side face runs on into the receiver's with no step at the seam, on the side the photos show: taken as the receiver's width. ± is a step of 0.02 in a side, which wouldn't show at this size.","via":"harvest"}}],"note":"No page gives it and no photo is square to it. The army's A2 grip is .885 across its top (aero-m4e1-lower.grip_body_width, drawing 9349127)."},"lug_slot_width":{"label":"The slot in the top that goes over the receiver's lug, across","kind":"length","measurements":[{"id":"front-photo","value":0.394,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-grip-mod-4 d736daca7a02 (BCM's BCM-MOD-4-GRIP-BLK-2: the black grip from ahead, from a little above, 1000 x 1000)","scaleRef":"the block's own width across the same face (bcm-grip-mod-4.top_block_width, 0.88 ± 0.04)","method":"on a 4x gridded crop at row 330 (the screw's hole), the walls' outer edges at columns 442.5 and 562.5 and the slot's walls at 477 and 530.75: 53.75 px of 120, 0.448 of the block. ± is 1.5 px on each of the slot's edges and the block's width.","via":"harvest"},"note":"Wider than the standard lug's .375 (std.ar15.grip_lug_width) by 0.01 a side: the slot goes over the lug."}],"note":"Read on BCM's photo of the grip from ahead, which looks down the slot (its floor lit, the screw's hole in it) between the block's two walls: the walls' inner faces and outer faces are four lines across one view, so their spacing along a row needs no scale but the walls' own width."},"rib_reach":{"label":"Front strap's ribs: how far back from the strap's edge they run, in the side view","kind":"length","measurements":[{"id":"photo","value":0.2,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-grip-mod-4 87b3693f2d0e (Primary Arms BCM-GFG-MOD-4-BLK_01: the black grip on white, straight right side, 2200 x 1467)","scaleRef":"the 4.179 in drop (bcm-grip-mod-4.bottom_below_lower_underside): 260.9 px/in","method":"read on a gridded 3x crop at rows 850 to 1100 (columns 1100 to 1400): the ribs' crests at the outline's edge and their rear ends (where their shadows stop, before the smooth band at the texture panel's border), 50 to 53 px apart. ± is 8 px.","via":"harvest"}}],"note":"Counted on the stored side outline turned upright (its front edge's crests, each the highest within a rib's pitch either way): 19 ribs from 1.41 to 3.32 in down the strap, 0.106 in apart on average (0.08 to 0.13 at the outline's 0.006 in simplification); on the photo they stand about 0.035 in out of the strap (8 to 10 px). From ahead (BCM's BLK-2) they run across the whole front strap between the two texture panels."},"base_wall":{"label":"The open bottom's rim: the wall round the opening at the base, across","kind":"length","measurements":[{"id":"assumed","value":0.12,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: Primary Arms' views from below (d41f5fa6a14e, f669645dcd74) show the rim at 25 to 80 px of a base 460 to 700 px across, at an angle no figure on file sets; the ± covers a rim from a fourteenth to a sixth of an inch.","via":"harvest"}}],"note":"BCM: \"Open bottom to minimize weight\". Primary Arms' two views from below (black and FDE) show the base as a rim round a rounded opening, the rim about a tenth of the base's span; neither is square to the base, so its width is drawn as assumed, not read."},"hollow_top_below_top":{"label":"How far up the open bottom's hollow reaches: its top, below the grip's flat top","kind":"length","measurements":[{"id":"assumed","value":1.3,"unit":"in","pm":0.4,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows the hollow's top. Taken under the slot's floor (the standard lug's depth, 0.93 in below the top, std.ar15.grip_lug_depth) with a wall under it for the screw's head to bear on; the ± runs from just under that floor to half way down the grip.","via":"harvest"}}],"note":"No view shows the hollow's top: the views from below see dark inside it. The screw goes down through the slot's floor (the hole in BCM's view from ahead) and its head is reached through the hollow."},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"model","value":2.48,"unit":"oz","pm":0.5,"source":{"type":"derived","basis":"The model's polymer volume, 3.767 cubic inches (pipeline/blender/bcm_grip_mod_4.py's manifest, volume_in3), times std.density.polymer (18.68 g, 0.659 oz to the cubic inch: a polyamide's; BCM says \"high quality impact resistant polymers\" and names no grade): 2.48 oz. The ± is the open bottom's assumed wall (± 0.05 in) and depth (± 0.4 in), about 0.3 and 0.2 oz, and a glass fill, which no page rules out (up to 0.2 g/ml heavier: 0.4 oz). The screw and washer BCM includes aren't drawn and aren't in it. app/tests/bcm-grip-mod-4.test.ts holds the model's volume to it.","via":"harvest"}}],"note":"No page gives it: BCM's own product data says \"weight\":null on both its pages, and KYGUNCO's \"Weight 2 lb\" is its shipping default (the same on its other parts' pages). Worked out from the model, below."}}},{"subject":"bcm-h-buffer","title":"BCM H carbine buffer","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"bcm","value":3.8,"unit":"oz","pm":0.05,"stated":"Weighted with 1 tungsten and 2 steel weights. 3.8oz.","source":{"type":"spec","publisher":"manufacturer","name":"Bravo Company USA, H Carbine Buffer (Buffer-Carbine-H)","url":"https://bravocompanyusa.com/h-carbine-buffer/","retrieved":"2026-10-12","via":"harvest"}},{"id":"primary-arms","value":3.8,"unit":"oz","pm":0.05,"stated":"Weight 3.8 oz.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Bravo Company Manufacturing AR-15 H1 Buffer - Carbine (Buffer-Carbine-H)","url":"https://www.primaryarms.com/bravo-company-manufacturing-carbine-h1-buffer-3-8-oz","retrieved":"2026-10-12","via":"harvest"}}],"adopt":{"from":"bcm","reason":"The seller's own figure; Primary Arms repeats it."}},"length":{"label":"Length (the head's front face to the bumper's end)","kind":"length","measurements":[{"id":"std","value":3.251,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.carbine_buffer.length}","via":"harvest"}}]},"od":{"label":"Diameter (its head, which runs in the extension's bore)","kind":"length","measurements":[{"id":"std","value":0.98,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.carbine_buffer.head_d}","via":"harvest"}}]}}},{"subject":"bcm-h2-buffer","title":"BCM H2 carbine buffer","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"bcm","value":4.6,"unit":"oz","pm":0.05,"stated":"Weighted with 2 tungsten and 1 steel weights. 4.6oz.","source":{"type":"spec","publisher":"manufacturer","name":"Bravo Company USA, H2 Carbine Buffer (Buffer-Carbine-H2)","url":"https://bravocompanyusa.com/h2-carbine-buffer/","retrieved":"2026-10-12","via":"harvest"}},{"id":"primary-arms","value":4.6,"unit":"oz","pm":0.05,"stated":"Weight 4.6 oz.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Bravo Company Manufacturing AR-15 H2 Buffer - Carbine (Buffer-Carbine-H2)","url":"https://www.primaryarms.com/bravo-company-usa-carbine-h2-buffer-weight-4.6oz.","retrieved":"2026-10-12","via":"harvest"}}],"adopt":{"from":"bcm","reason":"The seller's own figure; Primary Arms repeats it."}},"length":{"label":"Length (the head's front face to the bumper's end)","kind":"length","measurements":[{"id":"std","value":3.251,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.carbine_buffer.length}","via":"harvest"}}]},"od":{"label":"Diameter (its head, which runs in the extension's bore)","kind":"length","measurements":[{"id":"std","value":0.98,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.carbine_buffer.head_d}","via":"harvest"}}]}}},{"subject":"bcm-h3-buffer","title":"BCM H3 carbine buffer","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"bcm","value":5.4,"unit":"oz","pm":0.05,"stated":"Weighted with 3 tungsten weights. 5.4oz.","source":{"type":"spec","publisher":"manufacturer","name":"Bravo Company USA, H3 Carbine Buffer (Buffer-Carbine-H3)","url":"https://bravocompanyusa.com/h3-carbine-buffer/","retrieved":"2026-10-12","via":"harvest"}},{"id":"primary-arms","value":5.4,"unit":"oz","pm":0.05,"stated":"Weight 5.4 oz.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Bravo Company Manufacturing AR-15 H3 Buffer - Carbine (Buffer-Carbine-H3)","url":"https://www.primaryarms.com/bravo-company-manufacturing-carbine-h3-buffer-5-4-oz","retrieved":"2026-10-12","via":"harvest"}}],"adopt":{"from":"bcm","reason":"The seller's own figure; Primary Arms repeats it."}},"length":{"label":"Length (the head's front face to the bumper's end)","kind":"length","measurements":[{"id":"std","value":3.251,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.carbine_buffer.length}","via":"harvest"}}]},"od":{"label":"Diameter (its head, which runs in the extension's bore)","kind":"length","measurements":[{"id":"std","value":0.98,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.carbine_buffer.head_d}","via":"harvest"}}]}}},{"subject":"bcm-handguard-cap-round-750","title":"BCM Handguard Cap Round - .750 AR15","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"metal","value":0.4,"unit":"oz","pm":0.02,"source":{"type":"derived","expr":"(0.785398163 * (({.skirt_od} - 2 * {.bend_r}) * ({.skirt_od} - 2 * {.bend_r}) - {.bore_d} * {.bore_d}) - {.slot_w} * ({.slot_hi} - {.slot_lo} - {.slot_w}) - 0.785398163 * {.slot_w} * {.slot_w} + 9.8696044 * ({.bend_r} - {.sheet} / 2) * ({.skirt_od} / 2 - {.bend_r}) + 6.28318531 * ({.bend_r} - {.sheet} / 2) * ({.bend_r} - {.sheet} / 2) + 3.14159265 * ({.skirt_od} - {.sheet}) * ({.length} - {.bend_r})) * {.sheet} * {std.density.steel}","via":"harvest"}}],"note":"WORKED OUT, not published: BCM states no weight or material for the cap. Its steel: the flat of the face (inside the bend, less the bore and the gas tube's hole), the quarter bend (at its mid-surface's middle) and the skirt behind it (at its mid-surface), each a sheet of the reference model's thickness, times std.density.steel. The lip's flare and the two tabs are the same sheet bent, about the same metal. The ± is the density's range and the hole's part in the bend. The model's volume in the same steel comes to the same to a hundredth of an ounce (its test)."},"journal_id":{"label":"Bore (the journal it fits: .750 or .625)","kind":"length","measurements":[{"id":"bcm","value":0.75,"unit":"in","pm":0.0005,"stated":"For .750 Diameter Barrel","source":{"type":"spec","publisher":"manufacturer","name":"BCM, Handguard Cap Round - .750 AR15","url":"https://bravocompanyusa.com/handguard-cap-round-750-ar15","retrieved":"2026-10-28","via":"harvest"}}]},"bore_d":{"label":"The bore's diameter","kind":"length","measurements":[{"id":"model","value":19.0754,"unit":"mm","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Handguard_Endcap.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of the mil-spec parts; its end cap is a round one)","method":"its STEP surfaces read as text: the bore a cylinder of r 9.5377 mm about the axis","via":"user"},"note":"0.751 in: a thousandth over BCM's .750 journal."}]},"lip_od":{"label":"The skirt's lip, outside (its widest)","kind":"length","measurements":[{"id":"model","value":43,"unit":"mm","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Handguard_Endcap.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of the mil-spec parts; its end cap is a round one)","method":"the lip's outside, a cylinder of r 21.5 mm from the open edge forward 1.043 mm","via":"user"}},{"id":"bcm-photo","value":1.69,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/bcm-handguard-cap-round-750 6aea7065ddd1 (BCM's photo of the cap, its face from a little below, 500 x 491)","scaleRef":"the bore: BCM's \"For .750 Diameter Barrel\" (bore_d, 0.751)","method":"dark runs along rows (luminance < 150): the rim 387 px across at its widest row, the bore 172 px across at its; across, where the view's tilt doesn't shorten either (.cache/batch15/bcm-handguard-cap-round-750/scripts/rows.py)","via":"harvest"},"note":"387/172 × 0.751 = 1.690. The ± is two pixels at each edge. It checks the reference model's proportion on BCM's own cap: 0.444 here, 0.4436 there."}],"adopt":{"from":"model","reason":"The reference model's figure, a mil-spec round cap; BCM's photo puts its own cap's rim within 0.003 in of it, scaled by the bore."},"note":"The skirt's last millimetre at its open edge stands 0.15 mm proud of the rest, an S-bend between: a lip the handguard's front goes in past."},"skirt_od":{"label":"The skirt, outside (behind the lip)","kind":"length","measurements":[{"id":"model","value":42.7,"unit":"mm","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Handguard_Endcap.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of the mil-spec parts; its end cap is a round one)","method":"a cylinder of r 21.35 mm, from the lip's S-bend to the bend into the face (and the bend's outside, a torus of tube r 3.0 mm about a circle of r 18.35 mm, ends on it)","via":"user"}}]},"sheet":{"label":"The sheet's thickness","kind":"length","measurements":[{"id":"model","value":0.8128,"unit":"mm","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Handguard_Endcap.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of the mil-spec parts; its end cap is a round one)","method":"the face's two planes 0.8128 mm apart (z −7.0 and −6.1872), and the skirt's two cylinders (r 21.35 and 20.5372; r 21.5 and 20.6872 at the lip)","via":"user"},"note":"0.032 in."}]},"length":{"label":"Depth along the bore","kind":"length","measurements":[{"id":"model","value":7,"unit":"mm","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Handguard_Endcap.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of the mil-spec parts; its end cap is a round one)","method":"the face's front plane at z −7.0 and the skirt's edge (a plane ring) at z 0","via":"user"},"note":"0.276 in."}],"note":"From the face's front (against the front sight base) to the skirt's open edge."},"lip_len":{"label":"The lip's length from the open edge","kind":"length","measurements":[{"id":"model","value":1.0428,"unit":"mm","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Handguard_Endcap.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of the mil-spec parts; its end cap is a round one)","method":"the lip's cylinder r 21.5 from z 0 to −1.0428, where its S-bend (two tori of tube r 0.762 and 1.016) begins","via":"user"}}]},"lip_bend_len":{"label":"The lip's S-bend along the bore","kind":"length","measurements":[{"id":"model","value":0.7148,"unit":"mm","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Handguard_Endcap.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of the mil-spec parts; its end cap is a round one)","method":"the S-bend's two tori between z −1.0428 and −1.7576","via":"user"}}]},"bend_r":{"label":"The bend from the face to the skirt (outside)","kind":"length","measurements":[{"id":"model","value":3,"unit":"mm","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Handguard_Endcap.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of the mil-spec parts; its end cap is a round one)","method":"a torus of tube r 3.0 (outside) and 2.1872 (inside) about a circle of r 18.35 mm at z −4.0","via":"user"}}]},"slot_w":{"label":"The gas tube's hole: its width","kind":"length","measurements":[{"id":"model","value":4.7,"unit":"mm","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Handguard_Endcap.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of the mil-spec parts; its end cap is a round one)","method":"its two flat sides, planes 2.35 mm either side of the line over the bore","via":"user"}}]},"slot_lo":{"label":"The gas tube's hole: its lower end above the bore axis","kind":"length","measurements":[{"id":"model","value":13.425,"unit":"mm","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Handguard_Endcap.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of the mil-spec parts; its end cap is a round one)","method":"its lower end, a half cylinder r 2.35 about a centre 15.775 mm over the axis","via":"user"}}]},"slot_hi":{"label":"The gas tube's hole: its upper end above the bore axis","kind":"length","measurements":[{"id":"model","value":19.125,"unit":"mm","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Handguard_Endcap.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of the mil-spec parts; its end cap is a round one)","method":"its upper end, a half cylinder r 2.35 about a centre 16.775 mm over the axis","via":"user"}}],"note":"The hole runs up into the bend: the face is flat to 18.35 mm from the axis."},"tab_w":{"label":"The two tabs at the sides: their width","kind":"length","measurements":[{"id":"model","value":4.5,"unit":"mm","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Handguard_Endcap.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of the mil-spec parts; its end cap is a round one)","method":"the tab's two flat sides, planes 2.25 mm either side of the line across the bore","via":"user"}}],"note":"At 3 and 9 o'clock (square across from the gas tube's hole), the bend is pressed in: a strip of it set in toward the bore, as BCM's photo shows two square notches at the sides of its cap's rim."},"tab_set_r":{"label":"The tabs: their outside face from the bore axis","kind":"length","measurements":[{"id":"model","value":18.35,"unit":"mm","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Handguard_Endcap.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of the mil-spec parts; its end cap is a round one)","method":"the tab's outside, a plane 18.35 mm from the axis from the face's front (z −7.0) back to z −5.75","via":"user"}}]},"tab_bend_r":{"label":"The tabs: their bend (outside)","kind":"length","measurements":[{"id":"model","value":2,"unit":"mm","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Handguard_Endcap.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of the mil-spec parts; its end cap is a round one)","method":"a cylinder of r 2.0 (outside) and 2.8128 (inside) across the tab, its axis 20.35 mm from the bore axis at z −5.75","via":"user"}}]},"tab_bend_x":{"label":"The tabs: their bend's centre behind the face's front","kind":"length","measurements":[{"id":"model","value":1.25,"unit":"mm","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Handguard_Endcap.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of the mil-spec parts; its end cap is a round one)","method":"the tab bend's axis at z −5.75, the face's front at z −7.0","via":"user"}}]},"tab_step_x":{"label":"The tabs: their step out to the skirt, behind the face's front","kind":"length","measurements":[{"id":"model","value":3.25,"unit":"mm","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Handguard_Endcap.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of the mil-spec parts; its end cap is a round one)","method":"the tab's outside step, a plane at z −3.75 from the bend (20.35 mm from the axis) out to the skirt's flat (21.30); its inside step at z −2.937","via":"user"}}]},"width":{"label":"Width across","kind":"length","measurements":[{"id":"lip","value":43,"unit":"mm","pm":0.001,"source":{"type":"derived","expr":"{.lip_od}","via":"harvest"},"note":"The lip's, its widest."}]},"height":{"label":"Height","kind":"length","measurements":[{"id":"lip","value":43,"unit":"mm","pm":0.001,"source":{"type":"derived","expr":"{.lip_od}","via":"harvest"}}]}}},{"subject":"bcm-handguard-cap-triangle-750","title":"BCM Handguard Cap Triangle - .750 AR15","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"metal","value":0.31,"unit":"oz","pm":0.02,"source":{"type":"derived","expr":"(1.5 * ({.corner_r} * {.corner_r} * (120 - 2 * {.side_half_angle}) * 0.0174532925 + 2 * {.corner_circle_r} * {.corner_r} * sin(60 - {.side_half_angle}) + 2 * {.side_r} * {.side_r} * {.side_half_angle} * 0.0174532925 - 2 * {.side_centre_r} * {.side_r} * sin({.side_half_angle})) - 3 * ({.corner_r} * (120 - 2 * {.side_half_angle}) + 2 * {.side_r} * {.side_half_angle}) * 0.0174532925 * {.bend_r} + 3.14159265 * {.bend_r} * {.bend_r} - 0.785398163 * {.bore_d} * {.bore_d} - {.slot_w} * ({.slot_hi} - {.slot_lo} - {.slot_w}) - 0.785398163 * {.slot_w} * {.slot_w} + 1.57079633 * ({.bend_r} - {.sheet} / 2) * (3 * ({.corner_r} * (120 - 2 * {.side_half_angle}) + 2 * {.side_r} * {.side_half_angle}) * 0.0174532925 - 6.28318531 * {.bend_r} + 4 * ({.bend_r} - {.sheet} / 2)) + (3 * ({.corner_r} * (120 - 2 * {.side_half_angle}) + 2 * {.side_r} * {.side_half_angle}) * 0.0174532925 - 3.14159265 * {.sheet}) * ({.skirt_depth} + {.sheet} - {.bend_r}) + 3.14159265 * ({.bore_d} + {.sheet}) * {.collar}) * {.sheet} * {std.density.steel}","via":"harvest"}},{"id":"linemount","value":0.3,"unit":"oz","pm":0.05,"stated":"Weight: 0.3 oz","source":{"type":"spec","publisher":"retailer","name":"ar15discounts.com, Linemount Retro M16 Triangular Handguard Cap 0.75 (AR-RT-HGC1-T; not BCM's)","url":"https://ar15discounts.com/products/linemount-retro-m16-triangular-handguard-cap-0-75/","retrieved":"2026-10-28","via":"harvest"},"note":"Another maker's triangular .750 cap (\"Made from high-quality stamped steel with a classic blued finish\"). The page's \"Dimensions 4 × 2 × 2 in\" is its box."}],"adopt":{"from":"metal","reason":"BCM's cap's own sizes (the drawing's, at BCM's bore) and steel; Linemount's 0.3 oz is another maker's cap, stated to a tenth of an ounce, and inside this ±."},"note":"WORKED OUT, not published: BCM states no weight or material for the cap. Its steel (the drawing's note 1: \"STEEL, CMPSN 1045 THRU 1070, COLD ROLLED, SPHEROIDIZE ANNEALED, SPEC QQ-S-700\"): the flat of the face (the outline, its area by Green's theorem round the drawing's six arcs, moved in by the bend: A − P r + π r²) less the bore and the gas tube's hole, the quarter bend round it (at its mid-surface's middle), the skirt behind it (at its mid-surface's length round) and the collar round the bore, each a sheet of the drawing's thickness, times std.density.steel. The ± covers the sheet's ± .001 (4%), the bend's ± .01 and the density's range. The model's volume in the same steel comes to the same to a hundredth of an ounce (its test). Linemount's figure for its own triangular .750 cap (a reproduction, another maker's stamping of the same part) agrees."},"journal_id":{"label":"Bore (the journal it fits: .750 or .625)","kind":"length","measurements":[{"id":"bcm","value":0.75,"unit":"in","pm":0.0005,"stated":"For .750 Diameter Barrel","source":{"type":"spec","publisher":"manufacturer","name":"BCM, Handguard Cap Triangle - .750 AR15","url":"https://bravocompanyusa.com/handguard-cap-triangle-750-ar15/","retrieved":"2026-10-28","via":"harvest"}}]},"bore_clearance":{"label":"The bore over the journal it fits","kind":"length","measurements":[{"id":"tdp","value":0.0025,"unit":"in","pm":0.0025,"stated":".625 DIA +.005","source":{"type":"standard","doc":"US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"}}],"note":"The drawing's cap is bored \".625 DIA +.005\" for a .625 journal: up to five thousandths over it. Taken for BCM's .750 cap as the same stamping practice (BCM states no bore but its journal); the middle of the band, its ± the band's half."},"bore_d":{"label":"The bore's diameter","kind":"length","measurements":[{"id":"journal","value":0.7525,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{.journal_id} + {.bore_clearance}","via":"harvest"}}],"note":"BCM's journal and the drawing's clearance over it."},"tdp_bore_625":{"label":"The drawing's bore (the .625 cap's)","kind":"length","measurements":[{"id":"tdp","value":0.6275,"unit":"in","pm":0.0025,"stated":".625 DIA +.005","source":{"type":"standard","doc":"US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"The middle of .625 to .630."}],"note":"Kept for the record of what the drawing is for: BCM's cap is the .750 one, bore_d."},"sheet":{"label":"The sheet's thickness","kind":"length","measurements":[{"id":"tdp","value":0.025,"unit":"in","pm":0.001,"stated":".025±.001","source":{"type":"standard","doc":"US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"Section A-A: the face, the skirt and the collar are one sheet."}]},"length":{"label":"Depth along the bore","kind":"length","measurements":[{"id":"tdp","value":0.328,"unit":"in","pm":0.005,"stated":".328 REF","source":{"type":"standard","doc":"US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"Section A-A, a reference dimension: .240 + .025 + .063."}],"note":"From the skirt's open edge (where a handguard's front goes in) to the collar's front end (which bears on the front sight base): .240 to the face's inside, the sheet, and the collar."},"skirt_depth":{"label":"The skirt's depth inside, from its open edge to the face's inside","kind":"length","measurements":[{"id":"tdp","value":0.24,"unit":"in","pm":0.005,"stated":".240","source":{"type":"standard","doc":"US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"Section A-A: from the skirt's open edge to the face's rear (inner) surface."}],"note":"The pocket a drop-in handguard's front flange goes into: from the rim's open edge forward to the back of the face."},"collar":{"label":"The collar round the bore, ahead of the face","kind":"length","measurements":[{"id":"tdp","value":0.058,"unit":"in","pm":0.005,"stated":".063 -.010","source":{"type":"standard","doc":"US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"Section A-A: from the face's front surface to the collar's end. The middle of .053 to .063."}],"note":"The bore's edge is drawn forward, a short collar of the sheet: its front end is the cap's front, which bears on the front sight base's rear face. BCM's one 500 px photo of the face neither shows nor rules out its outside (the bore's wall reads deeper than the sheet: about 0.09 at its view's angle, which the collar's .088 is)."},"corner_r":{"label":"The three corners' radius (outside)","kind":"length","measurements":[{"id":"tdp","value":0.287,"unit":"in","pm":0.005,"stated":".287 R","source":{"type":"standard","doc":"US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"}}]},"corner_circle_r":{"label":"The corners' centres from the bore axis","kind":"length","measurements":[{"id":"tdp","value":0.625,"unit":"in","pm":0.005,"stated":".625 REF TO ℄ OF .287 R","source":{"type":"standard","doc":"US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"}}],"note":"The three corners' centres on one circle about the bore, 120° apart: the top one over the bore (the gas tube's side), the two below at 30° under the horizontal (the drawing's .312 REF and .541 REF are this at 30°)."},"side_r":{"label":"The three sides' radius (outside)","kind":"length","measurements":[{"id":"tdp","value":1.626,"unit":"in","pm":0.005,"stated":"1.626 R, 3 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"}}],"note":"Each side is an arc tangent to the two corners beside it: \"1.626 R, 3 PLACES TANGENT TO .287 RADII AND THROUGH POINTS DETERMINED BY 1.626 DIMENSIONS\" (its centre is the opposite corner's outer extreme, .912 from the bore, to the drawing's figures)."},"apex_r":{"label":"The bore axis to the top corner's outside","kind":"length","measurements":[{"id":"tdp","value":0.912,"unit":"in","pm":0.005,"stated":".912","source":{"type":"standard","doc":"US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"Section A-A."}],"note":"corner_circle_r + corner_r (.625 + .287 = .912)."},"width":{"label":"Width across","kind":"length","measurements":[{"id":"tdp","value":1.656,"unit":"in","pm":0.005,"stated":"1.656","source":{"type":"standard","doc":"US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"Across the two lower corners: 2 × (.541 + .287)."}]},"height":{"label":"Height","kind":"length","measurements":[{"id":"tdp","value":1.626,"unit":"in","pm":0.005,"stated":"1.626 3 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"}}],"note":"From the top corner to the bottom side, as from each corner to the side across from it."},"bend_r":{"label":"The bend from the face to the skirt (outside)","kind":"length","measurements":[{"id":"tdp","value":0.09,"unit":"in","pm":0.01,"stated":".09 R","source":{"type":"standard","doc":"US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"Section A-A, the leader on the bend's outside."}]},"slot_w":{"label":"The gas tube's hole: its width","kind":"length","measurements":[{"id":"tdp","value":0.187,"unit":"in","pm":0.002,"stated":".187±.002","source":{"type":"standard","doc":"US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"Its two ends \"FULL RADIUS\"."}],"note":"Windham Weaponry's triangular .750 cap: \"punched with an oblong hole for the gas tube\"."},"slot_lo":{"label":"The gas tube's hole: its lower end above the bore axis","kind":"length","measurements":[{"id":"tdp","value":0.513,"unit":"in","pm":0.005,"stated":".513","source":{"type":"standard","doc":"US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"}}]},"slot_hi":{"label":"The gas tube's hole: its upper end above the bore axis","kind":"length","measurements":[{"id":"tdp","value":0.737,"unit":"in","pm":0.005,"stated":".737","source":{"type":"standard","doc":"US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"}}]},"side_centre_r":{"label":"The side arcs' centres from the bore axis","kind":"length","measurements":[{"id":"arcs","value":0.912,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"(sqrt(4 * ({.side_r} - {.corner_r}) * ({.side_r} - {.corner_r}) - 3 * {.corner_circle_r} * {.corner_circle_r}) - {.corner_circle_r}) / 2","via":"harvest"}}],"note":"Where an arc of side_r tangent inside two corners of corner_r, on corner_circle_r 120° apart, has its centre: on the line through the third corner, q² + a q + a² = (side_r − corner_r)². The drawing's \"THROUGH POINTS DETERMINED BY 1.626 DIMENSIONS\" puts it at the opposite corner's outer extreme, apex_r: the two agree to a thousandth."},"side_half_angle":{"label":"The half of each side arc, about its centre","kind":"angle","measurements":[{"id":"arcs","value":23.84,"unit":"deg","pm":0.2,"source":{"type":"derived","basis":"acos((corner_circle_r / 2 + side_centre_r) / (side_r − corner_r)) with the drawing's .625, .287 and 1.626: 23.843°. The ± is what each figure's ± .005 moves it by.","via":"harvest"}}],"note":"From the side arc's centre, the angle between the line to the side's middle and the line to a corner's centre (where the arc meets that corner): cos β = (corner_circle_r / 2 + side_centre_r) / (side_r − corner_r). The ledger's expressions have no inverse cosine, so the figure is written here; app/tests/bcm-handguard-cap-triangle-750.test.ts works it out again from the four. Each corner's arc is then 120° − 2β. The weight's outline (its area and its length round) is taken over these six arcs."}}},{"subject":"bcm-kag-mlok","title":"BCM KAG (M-LOK® Compatible*), Kinesthetic Angled Grip","dimensions":{"length":{"label":"Overall length (the plate, along the handguard)","kind":"length","measurements":[{"id":"rs6-slots","value":2.73,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-kag-mlok bc3570df97d0 (Rifle Supply 1858_EDIT-6, 3737 x 3737: a rifle's right side, square on, muzzle up, the KAG on the handguard's bottom face with its deep end toward the muzzle)","scaleRef":"the handguard's centre column of M-LOK slots beside it (std.mlok.slot_pitch, 40 mm): the column's luminance along y autocorrelated, 573.2 px a pitch over rows 1000 to 3600 and 580.8 over rows 2000 to 3650, 577 ± 4 px: 366.4 px/in. The slots' length over their pitch reads 0.81, the standard's 32 over 40","method":"the plate's ends along the handguard's bottom edge, columns 2010 to 2030 (just off the handguard's edge at 1995 to 2005), luminance under 150: rows 2482 to 3483, 1001 px. The ± covers the pitch's two readings (2.71 to 2.75) and the plate's ends' 3 px each; the plate lies 0.3 in nearer the lens's axis than the slots' face, under 1% at any lens a product shot is taken with","via":"harvest"}},{"id":"bcm5-slots","value":2.71,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/bcm-kag-mlok b9ff51bbaa16 (BCM's own BCM-KAG-MCMR-BLK-5, 1500 x 1000: the KAG on an MCMR's bottom M-LOK face, an oblique from below the rifle's right side, muzzle to the lower right, the deep end toward the receiver)","scaleRef":"the MCMR's lower row of M-LOK slots beside the plate, the standard's 40 mm pitch: three slots' starts along the handguard's axis 305 and 310 px apart on a 1.4x crop","method":"the plate's two ends where it meets the handguard, along the same axis: 530 px on the same crop (by eye on the crop, (190,128) to (640,408)); oblique and by eye, so a check on the reading above and not adopted","via":"harvest"}}],"adopt":{"from":"rs6-slots","reason":"A square side view with the slots' pitch read by autocorrelation; BCM's own photo of it fitted is oblique and read by eye, and agrees within 0.02 in."},"note":"The mounting plate's two ends: the deep end's lip at the rear (the plate overhangs the deep end's back face) and the tail's tip. Two installed photos read it by their handguards' M-LOK slots; BCM's own side view of it alone, scaled by its two T-nuts as the M-LOK interval apart, would read 2.77 (893 px over the nuts' 254 px): that is the check below (nut_spacing), not a third reading."},"height":{"label":"Height (the mounting face to the deep end's toe)","kind":"length","measurements":[{"id":"rs6-slots","value":1.684,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-kag-mlok bc3570df97d0 (Rifle Supply 1858_EDIT-6: the KAG fitted, the rifle's right side square on)","scaleRef":"the same handguard's M-LOK slot pitch: 366.4 px/in (the length's rs6-slots)","method":"the handguard's bottom edge, which the plate bears on (column 1995 to 2007 down the photo, 2000 at the toe's row), to the toe's furthest point (column 2617 at row 2862, the same at luminance 100, 128 and 160): 617 px","via":"harvest"}},{"id":"bcm2-outline","value":1.721,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-kag-mlok 1693a668bba4 (BCM's BCM-KAG-MCMR-BLK-2, 1499 x 1000: the KAG alone on white, its left side square on, its T-nuts up)","scaleRef":"the length (.length, 2.73 in) over the plate's 893 px at luminance under 128 (the side outline's): 327.1 px/in","method":"the side outline's height (tools/trace.py): the mounting face (row 225, the plate's top edge) to the toe's lowest row at luminance under 128; the toe's soft shadow on the white below reaches row 813 at 200, which isn't the part","via":"harvest"}}],"adopt":{"from":"rs6-slots","reason":"Read square on, by the slots in the same photo; BCM's outline, at the scale the length gives it, has the toe 0.03 in further, within the two readings' ±."},"note":"From the face that bears on the handguard to the lowest point of the deep end's toe, square to the face."},"width":{"label":"Width (side to side, the plate)","kind":"length","measurements":[{"id":"rs3-nuts","value":0.65,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/bcm-kag-mlok 7f6a45ab8518 (Rifle Supply 1858_EDIT-3, 2934 x 2934: the mounting face toward the lens, its two T-nuts standing on it, the deep end beyond the face's far edge)","scaleRef":"its own two T-nuts' screws, taken as the M-LOK interval apart (std.mlok.interval, 20 mm), 279 px; the plate's length at .length gives 351 px/in, the same within 1%","method":"the face's two long edges across the tail's half (rows 1505 and 1732 at columns 1600 to 1900), 227 px. The photo is taken a little from one side (a band of the far wall shows beyond the face's far edge), so the face is foreshortened across: the ± takes up to 18 degrees of that, and the rounded edges","via":"harvest"}}],"note":"No view on file is square to the part's end or its face. The plate and the deep end are one width in the views from below (the toe's end face and the tail's underside, Rifle Supply 1858_EDIT-4); the model takes this for both."},"weight":{"label":"Weight (the moulding)","kind":"mass","measurements":[{"id":"model","value":0.78,"unit":"oz","pm":0.2,"source":{"type":"derived","basis":"The model's polymer volume, 1.187 cubic inches (pipeline/blender/bcm_kag_mlok.py's manifest, body_volume_in3; the screws' heads apart), times std.density.polymer (18.68 g, 0.659 oz to the cubic inch): 22.0 g. The ± is a glass fill's, which no page rules out (up to 0.2 g/ml heavier: 0.14 oz), the width's ± 0.05 in (0.06 oz), and what the moulding is cored inside that no view shows (the model's only hollow is the face's). app/tests/bcm-kag-mlok.test.ts holds the model's volume to it.","via":"harvest"}}],"note":"No page gives it: BCM's own product data says \"weight\":null, and KYGunCo's \"Weight 2 lb.\" (the discovery's reading of its page) is a shipping figure for a polymer grip that sells for $18.95. Worked out: the model's polymer volume times a polyamide's density (std.density.polymer: Zytel nylon 66, 1.140 g/ml; BCM names no grade, and a glass-filled grade would be heavier: the ± takes 0.2 g/ml). The steel T-nuts and screws aren't drawn and aren't in it."},"lugs":{"label":"M-LOK slots its lugs span","kind":"count","measurements":[{"id":"photo","value":1,"unit":"count","source":{"type":"photo","photo":"references/bcm-kag-mlok 1693a668bba4 (BCM's BCM-KAG-MCMR-BLK-2: its left side square on, its T-nuts up)","scaleRef":"the length (.length) over the plate's 893 px","method":"the two nuts' centres 0.777 in apart (nut_spacing): both fit one slot of the standard's 1.26 in, at its interval","via":"harvest"}}],"note":"Its two T-nuts stand 0.77 in apart (nut_spacing): one in each half of a single 32 mm slot, as Magpul's hand stop's and MVG's do. BCM's page names no count."},"reach_inside":{"label":"Reach inside the handguard (below the mounting face, tightened)","kind":"length","measurements":[],"note":"Not sourced: BCM gives no T-nut figure. The nuts stand 0.15 in above the face in BCM's side view as shipped, turned and loose; tightened they draw up under the slot's lips."},"lug_x":{"label":"Rear lug's centre ahead of the part's rear end","kind":"length","measurements":[{"id":"bcm2","value":0.767,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-kag-mlok 1693a668bba4 (BCM's BCM-KAG-MCMR-BLK-2: its left side square on, its T-nuts up)","scaleRef":"the length (.length, 2.73 in) over the plate's 893 px at luminance under 128, the side outline's frame: 327.1 px/in","method":"the rear nut's centre (column 939, the middle of its run of dark columns 867 to 1011 in rows 176 to 224) from the plate's rear end at that threshold (column 1190): 251 px","via":"harvest"}}],"note":"The rear T-nut's screw comes up through the deep end, from the big bore in its toe; the front one's through the tail, from the counterbore in its underside (Rifle Supply 1858_EDIT-4, from below; BCM's -4)."},"nut_spacing":{"label":"Its two T-nuts' centres, apart","kind":"length","measurements":[{"id":"bcm2","value":0.777,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bcm-kag-mlok 1693a668bba4 (BCM's BCM-KAG-MCMR-BLK-2: its left side square on, its T-nuts up)","scaleRef":"the length (.length, 2.73 in) over the plate's 893 px: 327.1 px/in","method":"the two nuts' runs of dark columns in rows 176 to 224 (612 to 758 and 867 to 1011): their middles 685 and 939, 254 px apart","via":"harvest"}}],"note":"The check on the length: BCM's own side view, at the scale the installed photo's slots give the plate, puts its two nuts 0.777 in apart, which is the M-LOK interval (std.mlok.interval, 20 mm: 0.787) less 1.3%. The scale wasn't set by the nuts."},"face_rim":{"label":"Mounting face: the rim round its hollow, wide","kind":"length","measurements":[{"id":"rs3","value":0.1,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-kag-mlok 7f6a45ab8518 (Rifle Supply 1858_EDIT-3: the mounting face toward the lens)","scaleRef":"its two nuts as the M-LOK interval apart: 354 px/in along the part","method":"the rim at the tail's end and along the near long edge, 33 to 38 px, by eye on a full-size crop","via":"harvest"}}],"note":"The face that bears on the handguard is a rim round a hollow (Rifle Supply 1858_EDIT-3, BCM's FDE -4): the nuts' posts and the moulded words stand in the hollow."},"face_hollow_depth":{"label":"Mounting face: the hollow's depth","kind":"length","measurements":[{"id":"assumed","value":0.06,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows the hollow in section. Under the plate's 0.11 in at the tail's tip (the side outline), and the floor is seen well below the rim in the face-on photos.","via":"harvest"}}]},"cup_depth":{"label":"The deep end's side panel (the BCM mark's cup), deep","kind":"length","measurements":[{"id":"assumed","value":0.05,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the cup on each side of the deep end is seen in every side photo, and its depth in none square to it.","via":"harvest"}}]},"cup_rim":{"label":"The deep end's side panel: the rim round it, wide","kind":"length","measurements":[{"id":"bcm2","value":0.1,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-kag-mlok 1693a668bba4 (BCM's BCM-KAG-MCMR-BLK-2: its left side square on)","scaleRef":"327.1 px/in (the length over the plate's 893 px)","method":"the rim between the deep end's outline and its cup, 30 to 36 px on the cup's back and toe, by eye on the photo","via":"harvest"}}]},"cup_top":{"label":"The deep end's side panel: its top edge below the mounting face","kind":"length","measurements":[{"id":"bcm2","value":0.4,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-kag-mlok 1693a668bba4 (BCM's BCM-KAG-MCMR-BLK-2: its left side square on)","scaleRef":"327.1 px/in","method":"the cup's top edge (row 355 to 360 on the photo) below the face (row 224), by eye","via":"harvest"}}]},"cup_front":{"label":"The deep end's side panel: its front edge at the top, ahead of the part's rear end","kind":"length","measurements":[{"id":"bcm2","value":0.96,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-kag-mlok 1693a668bba4 (BCM's BCM-KAG-MCMR-BLK-2: its left side square on)","scaleRef":"327.1 px/in","method":"the cup's upper front corner, column 880 to 885 (the plate's rear end at 1194), by eye; below it the cup's front edge runs down to the deep end's front face and follows it a rim's width in","via":"harvest"}}]},"toe_bore":{"label":"The bore in the deep end's toe (to the rear nut's screw), across","kind":"length","measurements":[{"id":"rs4","value":0.42,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/bcm-kag-mlok 5a8eea1dd41e (Rifle Supply 1858_EDIT-4: the toe's end face toward the lens, the tail's underside beside it)","scaleRef":"the toe's end face across, as the width (.width, 0.65 in): 240 px on a full-size crop","method":"the bore's rim across the same face, 155 px","via":"harvest"}}]},"toe_bore_depth":{"label":"The bore in the deep end's toe: how far in the screw's head stands","kind":"length","measurements":[{"id":"assumed","value":0.75,"unit":"in","pm":0.2,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the rear screw's head is seen well down the bore from the toe (Rifle Supply 1858_EDIT-4, BCM's -4); how far isn't seen. Its screw reaches the nut above the plate.","via":"harvest"}}]},"tail_counterbore":{"label":"The counterbore in the tail's underside (the front nut's screw), across","kind":"length","measurements":[{"id":"rs4","value":0.34,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-kag-mlok 5a8eea1dd41e (Rifle Supply 1858_EDIT-4: the tail's underside beside the toe)","scaleRef":"the tail's underside across, as the width (.width, 0.65 in): 220 px on a full-size crop","method":"the counterbore's rim across the underside, 115 px","via":"harvest"}}]},"screw_head":{"label":"The screws' heads, across","kind":"length","measurements":[{"id":"rs4","value":0.25,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-kag-mlok 5a8eea1dd41e (Rifle Supply 1858_EDIT-4: the front screw's head in its counterbore)","scaleRef":"the counterbore (.tail_counterbore, 0.34 in): 115 px","method":"the black head inside it, 85 px across, a socket head with a hex","via":"harvest"}}]},"plan_corner":{"label":"The plate's corners in plan, rounded to","kind":"length","measurements":[{"id":"rs3","value":0.08,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-kag-mlok 7f6a45ab8518 (Rifle Supply 1858_EDIT-3: the mounting face toward the lens)","scaleRef":"its two nuts as the M-LOK interval apart: 354 px/in along the part","method":"the face's four corners, each a quarter round of 25 to 30 px, by eye on a full-size crop","via":"harvest"}}]},"rib_pitch":{"label":"The ribs across the tail's underside and the deep end's front and back: their pitch along the surface","kind":"length","measurements":[{"id":"bcm2","value":0.061,"unit":"in","pm":0.003,"source":{"type":"photo","photo":"references/bcm-kag-mlok 1693a668bba4 (BCM's BCM-KAG-MCMR-BLK-2: its left side square on)","scaleRef":"327.1 px/in (the length over the plate's 893 px, the side outline's frame)","method":"the back face's straight run, rows 381 to 558: the silhouette's rightmost column per row dips at each gap between two ribs, ten spacings of 19 to 20 px (20.0 px median); the deep end's front face reads 18 to 19 px per row on a face that leans, the same along it","via":"harvest"}}],"note":"BCM: \"Textured in front and back for positive engagement\". The ribs run across the part (Rifle Supply 1858_EDIT-4, from below) and through its sides: BCM's side view shows them in its silhouette as teeth, along the tail's underside from the tip, down the deep end's front face, and on its back face."},"rib_gap":{"label":"The ribs: the gap between two, along the surface","kind":"length","measurements":[{"id":"bcm2","value":0.022,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/bcm-kag-mlok 1693a668bba4 (BCM's BCM-KAG-MCMR-BLK-2: its left side square on)","scaleRef":"327.1 px/in","method":"the gaps' widths on the back face's straight run, 6 to 8 px (median 7) of the 20 px pitch: the ribs are the wider","via":"harvest"}}]},"rib_depth":{"label":"The ribs: how far they stand off the surface between them","kind":"length","measurements":[{"id":"bcm2","value":0.025,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/bcm-kag-mlok 1693a668bba4 (BCM's BCM-KAG-MCMR-BLK-2: its left side square on)","scaleRef":"327.1 px/in","method":"the back face's silhouette, the ribs' tips at column 1115 and the gaps' floors at 1105 to 1108, 8 px; the tail's underside shows the same teeth in profile, smaller as the photo sees them along a slope","via":"harvest"}}]},"ribs_front_from_x":{"label":"The front run of ribs (the tail's underside and the deep end's front face): its first rib at the tail's tip, ahead of the rear end","kind":"length","measurements":[{"id":"bcm2","value":2.69,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-kag-mlok 1693a668bba4 (BCM's BCM-KAG-MCMR-BLK-2: its left side square on)","scaleRef":"327.1 px/in","method":"the first tooth under the tip, column 310 (the plate's rear end at 1190), by eye on a 2x enlargement","via":"harvest"}}]},"ribs_front_to_y":{"label":"The front run of ribs: its last rib on the deep end's front face, below the mounting face","kind":"length","measurements":[{"id":"bcm2","value":1.315,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-kag-mlok 1693a668bba4 (BCM's BCM-KAG-MCMR-BLK-2: its left side square on)","scaleRef":"327.1 px/in","method":"the last tooth down the deep end's front face, row 655 (the face at 225), by eye on a 2x enlargement; below it the toe is smooth","via":"harvest"}}]},"ribs_back_from_y":{"label":"The back run of ribs (the deep end's back face): its first rib below the mounting face","kind":"length","measurements":[{"id":"bcm2","value":0.159,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-kag-mlok 1693a668bba4 (BCM's BCM-KAG-MCMR-BLK-2: its left side square on)","scaleRef":"327.1 px/in","method":"the first tooth where the back face leaves the plate's rear corner, row 277, by eye on a 2x enlargement","via":"harvest"}}]},"ribs_back_to_y":{"label":"The back run of ribs: its last rib below the mounting face","kind":"length","measurements":[{"id":"bcm2","value":1.058,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-kag-mlok 1693a668bba4 (BCM's BCM-KAG-MCMR-BLK-2: its left side square on)","scaleRef":"327.1 px/in","method":"the last tooth down the back face, row 571, by eye on a 2x enlargement; below it the back face is smooth into the toe","via":"harvest"}}]},"ribs_back_count":{"label":"The back run of ribs: how many","kind":"count","measurements":[{"id":"bcm2","value":16,"unit":"count","source":{"type":"photo","photo":"references/bcm-kag-mlok 1693a668bba4 (BCM's BCM-KAG-MCMR-BLK-2: its left side square on)","scaleRef":"none: a count","method":"the teeth in the silhouette of the back face, rows 277 to 568, counted on a 1.6x enlargement (each 20 px apart on the straight run)","via":"harvest"}}],"note":"Counted on BCM's side view: thirteen down the straight back face at the 0.061 in pitch and three on the curve from the plate's rear corner, where they stand a little wider apart. The front run (the tail's underside and the deep end's front face) is counted by the model from its length over the pitch, 38; counted by eye on the same enlargement, 17 ahead of the front screw's head, about 7 beside and under it and 15 down the front face, 39 ± 2."},"front_head_proud":{"label":"The front screw's head: how far it stands proud of the ribs' tips on the tail's underside","kind":"length","measurements":[{"id":"bcm2","value":0.02,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/bcm-kag-mlok 1693a668bba4 (BCM's BCM-KAG-MCMR-BLK-2: its left side square on)","scaleRef":"327.1 px/in","method":"the silhouette's lowest row per column under the ramp (cols 640 to 725) against the ramp's line drawn straight from column 620 (row 373) to 730 (row 433): 3 to 7 px beyond it","via":"harvest"}}],"note":"BCM's side view shows a low bump under the ramp between columns 640 and 725 (x 1.42 to 1.68), centred at the front nut's x: the screw's black head, not the moulding's shape. It stands out of the ramp's line, which runs straight past it either side, by up to 7 px."},"edge_round":{"label":"The edges' round","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the moulding's edges are rounded in every photo, their radius read in none.","via":"harvest"}}]}}},{"subject":"bcm-m4-upper","title":"BCM M4 Upper Receiver Assembly (w/ Laser T-Markings) (BCM4-UR-M4)","dimensions":{"weight":{"label":"Weight (assembled: its forward assist and ejection port cover fitted; no barrel, bolt carrier or charging handle)","kind":"mass","measurements":[{"id":"big-tex","value":9.5945,"unit":"oz","pm":0.005,"stated":"Weight 9.5945176587468 oz","source":{"type":"spec","publisher":"retailer","name":"Big Tex Ordnance, BCM M4 Upper Receiver Assembly (w/ Laser T-Markings) (BCM4-UR-M4), Additional information","url":"https://www.bigtexordnance.com/product/bcm-m4-upper-receiver-assembly-w-laser-t-markings/","retrieved":"2026-10-05","via":"harvest"},"note":"272 g to the gram, as if read off a scale and converted; its \"Dimensions 8 × 4 × 2 in\" beside it are a parcel's."},{"id":"ar15discounts","value":11.008,"unit":"oz","stated":"Weight 11.008 oz","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, BCM GUNFIGHTER Assembled Upper Receiver (MPN BCM4-UR-M4), Additional information","url":"https://ar15discounts.com/products/bcmgunfighter-assembled-upper-receiver/","retrieved":"2026-10-05","via":"harvest"},"note":"0.688 lb. Its \"Dimensions 7.67 × 2.31 × 2.31 in\" beside it are the part's own length and height (overall_length, height_over_lugs)."}],"adopt":{"from":"big-tex","reason":"Neither page says part or parcel. The lighter is taken as the nearer to the part alone: the catalog's other forged upper weighs 8.65 oz with the same two assemblies fitted (its maker's page), and at 11.0 oz this one would be a quarter heavier in the same alloy. The heavier stays as the visible upper end."},"note":"BCM states none (its page's data: \"weight\":null). Two sellers do, 1.4 oz apart, and neither says whether it is the part's or the parcel's. A maker's or a reviewer's figure would settle it."},"overall_length":{"label":"The receiver's length, rear face to the end of the barrel-nut thread","kind":"length","measurements":[{"id":"standard","value":7.657,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{.front_face_x} - {.receiver_rear_x}","via":"harvest"},"note":"The Army's drawing: 6.999 −.006 behind the pivot lug's hole and .661 ± .003 ahead of it."},{"id":"ar15discounts","value":7.67,"unit":"in","pm":0.01,"stated":"Dimensions 7.67 × 2.31 × 2.31 in","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, BCM GUNFIGHTER Assembled Upper Receiver (MPN BCM4-UR-M4), Additional information","url":"https://ar15discounts.com/products/bcmgunfighter-assembled-upper-receiver/","retrieved":"2026-10-05","via":"harvest"},"note":"The first of three; the page doesn't say what each spans. It is the receiver alone: the forward assist's cap stands another 0.3 in behind the rear face."}],"adopt":{"from":"standard","reason":"The drawing dimensions both faces; the seller's figure agrees within its ±."},"note":"A check of the drawing's two ends against a seller's figure for this part: they agree within 0.013 in."},"height_over_lugs":{"label":"The receiver's height, the lugs' undersides to the rail's top","kind":"length","measurements":[{"id":"ar15discounts","value":2.31,"unit":"in","pm":0.01,"stated":"Dimensions 7.67 × 2.31 × 2.31 in","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, BCM GUNFIGHTER Assembled Upper Receiver (MPN BCM4-UR-M4), Additional information","url":"https://ar15discounts.com/products/bcmgunfighter-assembled-upper-receiver/","retrieved":"2026-10-05","via":"harvest"},"note":"The second of three (the third repeats it and isn't the width: the forward assist's housing and the deflector reach 1.9 across)."},{"id":"sum","value":2.306,"unit":"in","pm":0.025,"source":{"type":"derived","expr":"{.rail_top_above_pin} + {.lug_bottom_below_pin}","via":"harvest"},"note":"The rail's top above the pin line and the lugs' undersides below it."}],"adopt":{"from":"sum","reason":"The two figures it is the sum of are each sourced; the seller's 2.31 agrees within 0.004."}},"lug_bottom_below_pin":{"label":"The lugs' undersides below the pin line","kind":"length","measurements":[{"id":"tdp","value":0.216,"unit":"in","pm":0.008,"stated":".476 −.015 (the front lug), .471 −.010 (the rear), from -G-; lug holes .2525 ± .0015 below -G-","source":{"type":"standard","doc":"US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-1/3, Section A-A, and F-2/3, side elevation; user-supplied scan (Distribution Statement F), PDF pages 123 and 124","via":"user"},"note":"-G- is the flat underside. The front lug reaches .461 to .476 below it, the rear .461 to .471: the middle of the two, less the holes' .2525."},{"id":"photo","value":0.217,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-m4-upper b896edc62dc6 (Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 127.86 px/in in the mid-plane; the lens 4 to 5 in above the pin line, about 38 in away","method":"the traced outline's lowest point, 0.247 below the pin line (0.233 in the left photo): the lugs' near lower edges, 0.25 nearer the lens and seen from above, which read 0.03 low","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing dimensions it; the photo agrees within its ±."}},"bore_axis_above_pin":{"label":"Bore axis above the takedown pin centre","kind":"length","measurements":[{"id":"standard","value":0.8775,"unit":"in","pm":0.0015,"source":{"type":"derived","expr":"{std.ar15.bore_axis_y}","via":"harvest"},"note":"The standard's: BCM's page says it is \"Precision machined to correct Mil-Specs\" and \"Built to the correct Mil-Specs\". Not measured on this upper."}]},"receiver_rear_x":{"label":"The receiver's rear face behind the takedown pin (negative)","kind":"length","measurements":[{"id":"standard","value":-0.621,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.ar15.upper_rear_face_x}","via":"harvest"},"note":"The Army's drawing (8448524 and 12576280 alike: 6.999 −.006 behind the pivot lug's hole)."},{"id":"right","value":-0.61,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-m4-upper b896edc62dc6 (Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 127.86 px/in in the mid-plane; the lens about 38 in away over x 2.2 (the far rims' offsets in the two holes: 35.5 in, x 2.18)","method":"the silhouette's rear end over y 1.1 to 1.5 reads -0.646 to -0.666: the round body's near edge, 0.59 nearer the lens, which reads 1.6% long about the lens's foot: 2.2 + (-0.656 - 2.2) / 1.016","via":"harvest"}}],"adopt":{"from":"standard","reason":"The drawing dimensions the face; the photo, read through its lens, agrees within its ±."}},"front_face_x":{"label":"The receiver's front face (the end of its barrel-nut thread) ahead of the takedown pin","kind":"length","measurements":[{"id":"standard","value":7.036,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.ar15.upper_front_face_x}","via":"harvest"},"note":"The Army's drawing: .661 ± .003 ahead of the pivot lug's hole."},{"id":"right","value":7.04,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-m4-upper b896edc62dc6 (Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 127.86 px/in in the mid-plane; the lens about 38 in away over x 2.2","method":"the silhouette's front end reads 7.12: the thread's near rim, 0.62 nearer the lens (its front face shows as an ellipse 0.09 in across), 1.6% long about the lens's foot: 2.2 + (7.12 - 2.2) / 1.016","via":"harvest"}}],"adopt":{"from":"standard","reason":"The drawing dimensions the face; the silhouette's end is the thread's near rim, and through the lens it agrees within its ±."}},"shoulder_x":{"label":"The body's front shoulder, where the barrel-nut thread begins, ahead of the takedown pin","kind":"length","measurements":[{"id":"standard","value":6.591,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{.front_face_x} - {std.ar15.upper_barrel_thread_length}","via":"harvest"},"note":"The Army's .445 REF behind the front face (8448524; the M16A2's 12576280 gives the nose as .440 +.010)."},{"id":"right","value":6.59,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-m4-upper b896edc62dc6 (Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 127.86 px/in in the mid-plane; the lens about 38 in away over x 2.2","method":"the body's front face above and below the thread reads 6.653 at every height (one vertical line with the rail's front end): its near edge, 0.59 nearer the lens; 2.2 + (6.653 - 2.2) / 1.0155","via":"harvest"}}],"adopt":{"from":"standard","reason":"The drawing; the photo through its lens lands on it."}},"underside_y":{"label":"The receiver's underside above the pin line","kind":"length","measurements":[{"id":"standard","value":0.2485,"unit":"in","pm":0.0015,"source":{"type":"derived","expr":"{std.ar15.deck_y}","via":"harvest"},"note":"It sits on the lower's deck (the M16A2's drawing: lug holes .2525 ± .0015 below the underside -G-)."},{"id":"right","value":0.245,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-m4-upper b896edc62dc6 (Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 127.86 px/in in the mid-plane; the lens 4.0 to 5.2 in above the pin line, 35.5 to 38 in away (the far rims' offsets in the two holes; the hinge pin's height)","method":"the underside's edge between the lugs reads 0.193 above the pin line (a line fitted over 750 columns, rms 0.5 px): its near edge, 0.453 nearer the lens, seen from above; through the lens 0.241 to 0.252","via":"harvest"},"note":"Why no height is taken from this photo as it reads."}],"adopt":{"from":"standard","reason":"The drawing; the photo lands on it only through its lens."}},"width":{"label":"Width of the receiver's round body","kind":"length","measurements":[{"id":"tdp-a2","value":1.19,"unit":"in","pm":0.01,"stated":"(1.19) FORGED ∅ -B-","source":{"type":"standard","doc":"US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-2/3, Section D-D, and F-3/3, Section H-H; user-supplied scan (Distribution Statement F), PDF pages 124 and 126","via":"user"}},{"id":"tdp-a1","value":1.18,"unit":"in","pm":0.01,"stated":"FORGED DIA 1.18 DIA REF -V-","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 2 of 2, rev G: View G-G; user-supplied scan, references/tdp p109","via":"user"}},{"id":"banner","value":1.2,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/bcm-m4-upper c6717b54ef96 (BCM's shop, the upper receivers category's banner: an M4 flat top with T-marks, forward assist and port door from straight above, 1200 x 400)","scaleRef":"the rail's 13 slots at std.picatinny.slot_pitch: 121.27 px/in at the rail's top (rms 0.5 px); 118.2 px/in at the bore's height, by the forward assist's cap (.605 across, 9349084: 71.5 px)","method":"the body's two edges between the deflector and the forward assist's housing, 141 px apart; the ± is the lens's height (117 to 119 px/in)","via":"harvest"}}],"adopt":{"from":"tdp-a2","reason":"The drawing of the receiver the flat top derives from; the older drawing reads .01 less and BCM's own part from above .01 more, each within its ±."},"note":"The forging's drawing isn't in the package; both machined drawings give the round body's forged diameter as a reference. Its forward assist's housing, its deflector and the port cover's hinge stand out past it on the right."},"body_radius":{"label":"The round body's radius about the bore","kind":"length","measurements":[{"id":"tdp-a2","value":0.595,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{.width} / 2","via":"harvest"}},{"id":"model","value":0.6,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/research/aero-upper/step), cut at x 1.8: cylindrical faces r 0.6000 about the bore's axis","via":"user"}}],"adopt":{"from":"tdp-a2","reason":"The drawing's forged figure; the model's is 0.005 more."}},"bore_d":{"label":"The bore the bolt carrier runs in","kind":"length","measurements":[{"id":"tdp","value":1.001,"unit":"in","pm":0.001,"stated":"1.000 +.002 ∅ FIRST 1.110 +.030; 1.000 +.006 ∅ THRU REMAINDER","source":{"type":"standard","doc":"US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-3/3, front view; user-supplied scan (Distribution Statement F), PDF page 126","via":"user"}}]},"lug_width":{"label":"The two lugs' width","kind":"length","measurements":[{"id":"tdp","value":0.4945,"unit":"in","pm":0.0015,"stated":".496 −.003 BOTH LUGS","source":{"type":"standard","doc":"US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-2/3, rear view; user-supplied scan (Distribution Statement F), PDF page 124","via":"user"}}]},"lug_hole_d":{"label":"The two lugs' pin holes","kind":"length","measurements":[{"id":"tdp","value":0.2505,"unit":"in","pm":0.0015,"stated":".250 +.001 ∅ THRU (the pivot lug's); .250 +.002 ∅ THRU, C'SINK .30 +.02 ∅ X 88° +4° INCL THIS SIDE ONLY (the takedown lug's)","source":{"type":"standard","doc":"US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-1/3, Section A-A, and F-2/3, side elevation; user-supplied scan (Distribution Statement F), PDF pages 123 and 124","via":"user"},"note":"One figure for both; the takedown lug's countersink isn't drawn. In Primary Arms' photos both holes are see-through, 32 px across at 128 px/in."}]},"rail_top_above_pin":{"label":"The top rail's surface above the pin line","kind":"length","measurements":[{"id":"left","value":2.09,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-m4-upper b3b8d1ad9d16 (Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 137.71 px/in in the mid-plane; the lens 35 in away, 3.3 in above the pin line over x 3.9 (the far rims' offsets in the two holes)","method":"a line through the tooth tops (349 columns, rms 0.15 px) stands 2.078 above the pin line at mid-length; through the lens 2.090","via":"harvest"}},{"id":"right","value":2.09,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-m4-upper b896edc62dc6 (Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 127.86 px/in in the mid-plane; the lens 4.0 to 5.2 in above the pin line, 35.5 to 38 in away","method":"a line through the tooth tops (314 columns, rms 0.13 px) stands 2.068 above the pin line at mid-length; through the lens 2.086 to 2.094","via":"harvest"}},{"id":"model","value":2.09,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/batch123/bcm-m4-upper/cad_rail.py): the teeth's top planes at y 2.0900","via":"user"}}],"adopt":{"from":"left","reason":"The photo whose lens stood lowest (the least to correct); the right photo and the reference model of a mil-spec flat top give the same figure."},"note":"Each photo reads the top flat's near edge, 0.318 nearer the lens and seen from above: 2.068 and 2.078 as they stand."},"rail_slots":{"label":"How many rail slots","kind":"count","measurements":[{"id":"photo","value":13,"unit":"count","source":{"type":"photo","photo":"references/bcm-m4-upper b896edc62dc6 (Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins","method":"the gaps between the teeth along the top edge, counted (13 in the left photo and in BCM's banner from above too)","via":"harvest"}}],"note":"BCM's laser T-marks are in the even ones, T2 to T12 (its banner from above: T2 in the second slot from the rear): slot n, counted from 0 at the rear, is T(n + 1)."},"rail_slot0_x":{"label":"The rearmost rail slot's centre ahead of the takedown pin","kind":"length","measurements":[{"id":"left","value":1.31,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-m4-upper b3b8d1ad9d16 (Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins: 137.71 px/in; the 13 slots' centres 0.4008 apart in that frame (std.picatinny.slot_pitch: x 1.0173); the lens over x 3.9 (the far rims' offsets in the two holes)","method":"the 13 gaps' centres at the 50% level, the rearmost at 1.263: 3.91 + (1.263 - 3.91) / 1.0173 = 1.308; the ± is the lens's foot (± 0.7 in)","via":"harvest"}},{"id":"right","value":1.32,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-m4-upper b896edc62dc6 (Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins: 127.86 px/in; the 13 slots' centres 0.4006 apart in that frame (x 1.0168); the lens over x 2.2","method":"the rearmost gap's centre at 1.308: 2.18 + (1.308 - 2.18) / 1.0168 = 1.322; with the foot anywhere from x 1.45 to 2.4, 1.310 to 1.326","via":"harvest"}},{"id":"model","value":1.308,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/batch123/bcm-m4-upper/cad_rail.py): 13 slots, their walls from x 1.2033 / 1.4133 to 5.9313 / 6.1413 at a 0.394 pitch","via":"user"}}],"adopt":{"from":"left","reason":"Its lens stood nearest the rail's middle, so what the lens's place leaves unsure moves this slot least. The right photo reads 0.01 more and the reference model of a mil-spec flat top 0.002 less: three that agree within their ±."},"note":"In these photos the far teeth are blown out to the background's white, so the dark teeth are the rail's near edge, 0.42 nearer the lens: the slots' pitch reads 1.7% long in the pins' frame, and their places are taken about the lens's foot at the pitch the standard gives."},"rail_rear_x":{"label":"The top rail's head: where it begins ahead of the tongue, X (the app draws the head from here)","kind":"length","measurements":[{"id":"standard","value":0.4165,"unit":"in","pm":0.006,"source":{"type":"derived","expr":"{std.ar15.rail_tongue_shoulder_x}","via":"user"}}],"note":"Until 2026-10-20 this was the rail's rearmost point (now rail_tongue_rear_x), and the app drew the head at its full width from there, square: the charging handle's T, cut round for a rounded rail end, stood in its corners. Behind this the rail is the standard's tongue (std.ar15.rail_tongue_*), which the receiver's model carries, as the 22RB's does."},"rail_tongue_rear_x":{"label":"The top rail's tongue: its rounded end's rearmost point, X ahead of the takedown pin","kind":"length","measurements":[{"id":"banner","value":-0.62,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-m4-upper c6717b54ef96 (BCM's shop, the upper receivers category's banner: an M4 flat top with T-marks, forward assist and port door from straight above, 1200 x 400)","scaleRef":"the rail's 13 slots at std.picatinny.slot_pitch: 121.27 px/in at the rail's top (rms 0.5 px), the rearmost slot's centre at px 842.0 as rail_slot0_x","method":"the rounded end's apex at px 1076.1: 1.930 behind the rearmost slot's centre","via":"harvest"}},{"id":"model","value":-0.625,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/batch123/bcm-m4-upper/cad_rail.py): the rail's top plane from x -0.625 (its rear face) to 1.203","via":"user"}}],"adopt":{"from":"banner","reason":"The view that sees the end itself, on BCM's own part; the reference model agrees within 0.005."},"note":"Behind the first slot the rail runs solid over the charging handle's channel to an end rounded in plan, level with the receiver's rear face at its middle. (Primary Arms' right view reads that end's near corner, 0.29 off the middle: -0.595 as it stands, -0.57 through its lens, 0.05 ahead of the apex as the banner shows the rounding. Another point of the same end, so not a second measurement of this one.)"},"rail_front_x":{"label":"The top rail's front end ahead of the takedown pin","kind":"length","measurements":[{"id":"right","value":6.593,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-m4-upper b896edc62dc6 (Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins: 127.86 px/in in the mid-plane; the lens about 38 in away over x 2.2; the teeth's near edge reads x 1.0168 (the slots' pitch)","method":"the last tooth's front reads 6.6675: 2.18 + (6.6675 - 2.18) / 1.0168","via":"harvest"}},{"id":"model","value":6.591,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/batch123/bcm-m4-upper/cad_rail.py): the last tooth from x 6.141 to 6.591, its shoulder's plane","via":"user"}}],"adopt":{"from":"right","reason":"BCM's own part; the reference model agrees within 0.002."},"note":"Level with the body's front shoulder (shoulder_x): one vertical line in the side photo."},"charging_handle_above_bore":{"label":"The charging handle's channel above the bore's axis","kind":"length","measurements":[{"id":"photo","value":0.9,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/bcm-m4-upper b896edc62dc6 (Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins: 127.86 px/in in the mid-plane; the lens 4 to 5 in above the pin line, about 38 in away","method":"the see-through notch in the rear end, from the ledge under it (reads 1.594: its far edge, through the lens 1.62 to 1.64) to the rail's underside (reads 1.899: its near edge, 1.92): the middle, 1.775, less the bore's 0.8775","via":"harvest"}},{"id":"standard","value":0.8563,"unit":"in","pm":0.007,"source":{"type":"derived","expr":"{std.ar15.charging_handle_axis_y} - {.bore_axis_above_pin}","via":"user"},"note":"Riding on its guide lugs on the channel's tier: std.ar15.charging_handle_axis_y."}],"adopt":{"from":"standard","reason":"A handle rides on its guide lugs on the channel's tier (std.ar15.charging_handle_axis_y, the Army's drawing's); the photo reads the see-through notch's middle, which is the room the handle's block lies in and not what it rides on. At 0.9 every handle's top stood 0.024 in the channel's roof (2026-10-20)."},"note":"The gap under the rail's rear end where the handle's T lies: its middle. (The slot through the rear face is taller: from the bore's top to its roof, std.ar15.charging_handle_channel_roof_y; the catalog's other forged upper is placed by the open notch too.)"},"handle_seat_x":{"label":"The charging handle's seat: the front wall of the open notch under the rail's rear end, ahead of the takedown pin","kind":"length","measurements":[{"id":"right","value":0.068,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-m4-upper b896edc62dc6 (Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins: 127.86 px/in in the mid-plane; the lens 4 to 5 in above the pin line, about 38 in away","method":"the see-through notch's front wall in the traced outline (profiles.side): its flat at x 0.068 from y 1.657 to 1.775, between two corners cut back to x 0.017 and -0.023. What shows through a notch is bounded by the wall's near edge, half the receiver's width nearer the lens: from 38 in that reads 0.02 to 0.04 behind the wall itself, which ± covers on the one side","via":"harvest"}},{"id":"tdp","value":0.075,"unit":"in","pm":0.015,"source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: side elevation, scaled (the notch has no callout in this view); user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"},"note":"Scaled, not a callout. On the 6600 px scan the two lug holes, fitted as circles, are 1966 px apart (308.4 px/in over std.ar15.pin_spacing) and the notch's front wall (column 2427.5) is 21.5 px ahead of the takedown hole's centre: 0.070. From the rear face's line, 217 px behind the wall, it is 0.083: the drawing dimensions that face at -0.621 and the scan has it at -0.634 by the holes. Between the two; ± covers both. The notch is 0.31 to 0.32 high there, for the handle's .2985 (drawing 8448518), its front corners cut back 0.06."}],"adopt":{"from":"right","reason":"This receiver's own notch, where its model's wall is: a handle seated there stands in nothing. The Army's drawing, scaled, reads 0.007 more: within both ±."},"note":"Where a charging handle stops. The notch is cut across the receiver under the rail's rear end and is open to the rear: the handle's block (its T ahead of the wings or latches, as thick as the shaft) lies in it with its shoulder against this wall, and the shaft runs on through the slot ahead of it. Until 2026-10-05 the handle was placed with its shoulder at the rear face, 0.69 in behind this (that day's review of the models: its whole T hung behind the receiver, over the castle nut). A handle of the Army's length seated here ends 0.03 short of where the reference model's channel does (the front round's front, std.ar15.charging_handle_channel_front_round_x and _round_r, 5.9925, less 5.895 is 0.098). Magpul's photo of a handle in a receiver (references/magpul-mbus-3-rear 9248df8685e9) has it so: the T's wing astride the rear face, the notch filled to its front wall."},"left_photo_lens_x":{"label":"The left side photo: where its lens stands, X","kind":"length","measurements":[{"id":"holes","value":3.9,"unit":"in","pm":0.7,"source":{"type":"photo","photo":"references/bcm-m4-upper b3b8d1ad9d16 (Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 137.71 px/in in the mid-plane","method":"the far rims' offsets in the two holes (.cache/batch123/bcm-m4-upper/holes2.py), as rail_slot0_x states it: the lens over x 3.9, its foot ± 0.7","via":"harvest"}}],"note":"A property of Primary Arms' photo b3b8d1ad9d16: what stands nearer the lens than the mid-plane reads large about this point (rail_slot0_x and rail_top_above_pin are read through the same lens)."},"left_photo_lens_y":{"label":"The left side photo: where its lens stands, Y","kind":"length","measurements":[{"id":"holes","value":3.3,"unit":"in","pm":0.7,"source":{"type":"photo","photo":"references/bcm-m4-upper b3b8d1ad9d16 (Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 137.71 px/in in the mid-plane","method":"as left_photo_lens_x: 3.3 in above the pin line, as rail_top_above_pin states it (through it the tooth tops' 2.078 is 2.090); its ± taken as the foot's along the receiver","via":"harvest"}}]},"left_photo_lens_distance":{"label":"The left side photo: its lens's distance from the receiver's mid-plane","kind":"length","measurements":[{"id":"holes","value":35,"unit":"in","pm":10,"source":{"type":"photo","photo":"references/bcm-m4-upper b3b8d1ad9d16 (Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 137.71 px/in in the mid-plane","method":"as left_photo_lens_x: 35 in away, as rail_top_above_pin states it. The rail's near teeth, 0.42 nearer the lens, read 1.73% long in this frame (rail_slot0_x), which would make it 25: ± covers both, and moves what is read on the left wall by up to 0.007 in and the pad's foot by up to 0.011","via":"harvest"}}]},"cam_pad_face_z":{"label":"The cam pin's pad on the left side, its face out from the middle (Z, to the left)","kind":"length","measurements":[{"id":"model","value":0.5625,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/batch123/bcm-m4-upper/cad_ch.py): the round along the pad's top edge, r 0.0938 about an axis along x at (y 1.486, z -0.469), so its face at z -0.563; expo-arms-stripped-upper.cam_pad_face_z reads the same file's flat face at z -0.561 to -0.564 over x 4.60 to 5.58, y 1.05 to 1.63","via":"user"}}],"note":"The pad is the forging's: the Army's machined drawing doesn't show it (8448524 draws the right side, and the left only at the notch, View C-C). BCM's left photo has its foot at x 4.53 to 5.64, y 1.10 to 1.67 once brought back through the lens (profiles.left, cam_pin_pad); the reference model's flat face, x 4.60 to 5.58 and y 1.05 to 1.63, lies inside that foot but for its lower edge, 0.05 lower, where the photo's is in shadow and the face runs into the round body."},"cam_pad_edge_round":{"label":"The cam pin's pad, the round between its face and its foot: how far the face's edge lies inside the foot","kind":"length","measurements":[{"id":"left","value":0.115,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-m4-upper b3b8d1ad9d16 (Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 137.71 px/in in the mid-plane; the lens 35 in away, 3.3 in above the pin line over x 3.9 (left_photo_lens_*)","method":"the face's edge is the bright line inside the foot's soft one: columns 233.5 and 354.5 to 357 against the foot's 218.5 and 372.5 on rows 350 to 380, row 340.5 against the foot's 323.5 on columns 260 to 330: 15, 15.5 to 18 and 17 px, 0.109 to 0.131 in the mid-plane's scale, 1.6% less through the lens at the face's depth","via":"harvest"}},{"id":"model","value":0.094,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/batch123/bcm-m4-upper/cad_ch.py): the round along the pad's top edge, r 0.0938 about (y 1.486, z -0.469), and its two upper corners' rounds about z, r 0.0938 at x 4.695 and 5.488","via":"user"}}],"adopt":{"from":"left","reason":"BCM's own pad as its photo shows it; the reference model's round is 0.021 less, at the edge of the photo's ±."}},"latch_slot_wall":{"label":"The charging handle latch's slot in the left wall: the wall left between it and the notch's front wall (handle_seat_x)","kind":"length","measurements":[{"id":"tdp","value":0.156,"unit":"in","pm":0.005,"stated":".156","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: Section D-D (cut along the notch's centre line, View C-C: the left wall at the rear); user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}},{"id":"left","value":0.145,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bcm-m4-upper b3b8d1ad9d16 (Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 137.71 px/in in the mid-plane; the lens 35 in away, 3.3 in above the pin line over x 3.9 (left_photo_lens_*)","method":"rows 298 to 330: the slot's rear wall's shadow ends at u 970.3 and the notch shows through from u 990.5 (its front wall's near edge): 20.2 px, 0.147 in the mid-plane's scale, 0.9% less for the wall's face, 0.319 nearer the lens. (The same rows have a lit band from u 982 to 990.5, 0.158 high: the shallow step View C-C draws at the notch's front, not drawn here.)","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's callout; BCM's photo reads 0.011 less, a pixel and a half."},"note":"Where the latch's hook drops into the wall. Taken as: Section D-D is the left wall cut along the notch's centre line, its .195 the slot along the receiver and its .156 the wall behind the slot, to the notch's front end. Checked on the reference model (the slot's flat from x 0.233, which is .156 ahead of 0.077) and on BCM's own left photo."},"latch_slot_length":{"label":"The latch's slot, along the receiver (its ends full rounds of half this)","kind":"length","measurements":[{"id":"tdp","value":0.195,"unit":"in","pm":0.005,"stated":".195","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: Section D-D (cut along the notch's centre line, View C-C: the left wall at the rear); user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"},"note":"View C-C marks the slot's end FULL R."},{"id":"model","value":0.192,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/batch123/bcm-m4-upper/cad_ch.py): two rounds about z, r 0.0960, at (x 0.329, y 1.616) and (x 0.329, y 1.839), from the wall's face at z -0.318 in to the slot's floor at -0.251; the flat between them from x 0.233 to 0.425","via":"user"}},{"id":"left","value":0.2,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/bcm-m4-upper b3b8d1ad9d16 (Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 137.71 px/in in the mid-plane; the lens 35 in away, 3.3 in above the pin line over x 3.9 (left_photo_lens_*)","method":"rows 298 to 330: its front rim's bright line rises at u 942.5 and its rear wall's shadow ends at u 970.3: 27.8 px, 0.202, 0.9% less for the wall's face; the rim's line is two pixels wide","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's callout; the reference model's rounds make it 0.192 and BCM's photo reads 0.200: all three within their ±."}},"latch_slot_floor":{"label":"The latch's slot, the wall left under it: between its floor and the charging handle's channel","kind":"length","measurements":[{"id":"tdp","value":0.045,"unit":"in","pm":0.005,"stated":".045","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: Section D-D (cut along the notch's centre line, View C-C: the left wall at the rear); user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"},"note":"Taken as the strip of wall under the slot's floor: the two lines it is drawn between are the floor's and the wall's inner face."},{"id":"model","value":0.043,"unit":"in","pm":0.004,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/batch123/bcm-m4-upper/cad_ch.py): the slot's floor is a plane at z -0.251 from x 0.233 to 0.425, y 1.520 to 1.940, and the channel's wall beside it at z -0.208 (from the rear face to x 0.510)","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's callout; the reference model's is 0.002 less."},"note":"The slot is a pocket in the wall's outer face, not a window into the channel. Section D-D has .045 of wall under it; the reference model has its floor a plane over the slot's whole outline; and BCM's left photo has it lit inside (35 to 50 of 255 on rows 298 to 330, for the wall's 30), its rear wall's shadow across it, where a window into the channel would be the darkest thing on that side."},"latch_slot_bottom_y":{"label":"The latch's slot, its lower end above the pin line","kind":"length","measurements":[{"id":"left","value":1.527,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/bcm-m4-upper b3b8d1ad9d16 (Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 137.71 px/in in the mid-plane; the lens 35 in away, 3.3 in above the pin line over x 3.9 (left_photo_lens_*)","method":"columns 950 to 964: the slot's lower edge at v 341.5 (its rim bright at 340 to 341 toward the front, its shadow ending at 339 to 341 toward the rear), 208.0 px above the pin line there: 1.510, through the lens 1.527 (profiles.left, latch_slot)","via":"harvest"}},{"id":"model","value":1.52,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"as latch_slot_length: the lower round's centre at y 1.616, less its r 0.0960","via":"user"}}],"adopt":{"from":"left","reason":"BCM's own part; the reference model's is 0.007 lower, a pixel."},"note":"Its heights have no callout in View C-C or Section D-D: BCM's own photo, with the reference model beside it."},"latch_slot_top_y":{"label":"The latch's slot, its upper end above the pin line","kind":"length","measurements":[{"id":"left","value":1.926,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/bcm-m4-upper b3b8d1ad9d16 (Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 137.71 px/in in the mid-plane; the lens 35 in away, 3.3 in above the pin line over x 3.9 (left_photo_lens_*)","method":"columns 950 and 957: the lit foot of the rail above the slot ends at v 286 to 287, 263.5 px above the pin line there: 1.913, through the lens 1.926 (profiles.left, latch_slot)","via":"harvest"}},{"id":"model","value":1.935,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"as latch_slot_length: the upper round's centre at y 1.839, plus its r 0.0960","via":"user"}}],"adopt":{"from":"left","reason":"BCM's own part; the reference model's is 0.009 higher, a pixel."}},"rail_slot_floor_below_top":{"label":"The rail's slots, floor below the top (the reference model's)","kind":"length","measurements":[{"id":"model","value":0.115,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text (.cache/batch123/bcm-m4-upper/cad_rail.py): slot walls from y 1.975 to 2.090","via":"user"},"note":"MIL-STD-1913's .118 +.008 (std.picatinny.slot_depth) is what the app's rail is drawn to."}]},"dovetail_foot_y":{"label":"The rail's dovetail, its foot (where the neck begins), Y above the pin line","kind":"length","measurements":[{"id":"model","value":1.885,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/research/aero-upper/step/upper_secnums.py, run again 2026-10-05), cut at x 1.8: the 45° face from (0.333, 1.885) to (0.418, 1.969)","via":"user"}}]},"dovetail_foot_half_width":{"label":"The rail's dovetail at its foot, half its width","kind":"length","measurements":[{"id":"model","value":0.333,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"as dovetail_foot_y: the 45° face's lower end, z 0.333","via":"user"}},{"id":"std","value":0.323,"unit":"in","pm":0.013,"source":{"type":"derived","expr":"{std.picatinny.bevel_width} / 2 + {std.picatinny.lower_gauge_below_top} - ({.rail_top_above_pin} - {.dovetail_foot_y})","via":"harvest"},"note":"The standard's lower face carried on at its 45 degrees from the lower gauge line (.748 across, .154 below the rail's top) to the height the reference model has the foot at: the face every other rail on file has (the teeth the app draws on this body, a handguard's own rail) and every clamp's channel is cut to. ± is the gauge line's .010 and the model's .003."}],"adopt":{"from":"std","reason":"The standard's, since 2026-10-12: a rail's head is MIL-STD-1913's, and the clamps' channels are cut to it (pipeline/blender/lib.py rail_seat). The reference model draws the same face a hundredth further out, at the standard's stated .164 where the ledger has the middle of .164 -.020 (std.picatinny.lower_gauge_below_top): inside the standard's band, and on a body drawn so every clamp stood 0.008 in into the rail along both sides (0.001 cubic inches of an Aimpoint's base). The model isn't authoritative beside the standard (D49); its neck and the foot's height are still its own."}},"rail_neck_half_width":{"label":"The rail's neck below its dovetail, half its width","kind":"length","measurements":[{"id":"model","value":0.309,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"as dovetail_foot_y: planar faces z ±0.309 from y 1.700 to 1.885","via":"user"}}]},"rail_neck_bottom_y":{"label":"The rail's neck, where it meets the receiver's sides, Y","kind":"length","measurements":[{"id":"model","value":1.7,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"as dovetail_foot_y: the step out from ±0.309 to ±0.319 at y 1.700","via":"user"}}]},"side_half_width":{"label":"The receiver's flat sides below the rail's neck, half its width","kind":"length","measurements":[{"id":"model","value":0.319,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"as dovetail_foot_y: planar faces z ±0.319 from y 1.440 to 1.700, then a .10 fillet to the round body","via":"user"}},{"id":"banner","value":0.32,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-m4-upper c6717b54ef96 (BCM's shop, the upper receivers category's banner: an M4 flat top with T-marks, forward assist and port door from straight above, 1200 x 400)","scaleRef":"the rail's 13 slots at std.picatinny.slot_pitch: 121.27 px/in at the rail's top","method":"the teeth's top flats between their chamfers, 78 px across (0.643): the rail's flat top is as wide as the walls under it in the model (z ±0.318)","via":"harvest"},"note":"The top flat's width, the same ±0.318 in the reference model: a check that BCM's rail has the model's section, not a reading of the wall itself."}],"adopt":{"from":"model","reason":"The model's face; BCM's rail from above has the model's top flat."}},"side_bottom_y":{"label":"The receiver's flat sides, where they turn into the round body, Y","kind":"length","measurements":[{"id":"model","value":1.44,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"as dovetail_foot_y: the flat sides' lower end at y 1.440","via":"user"}}]},"lug_wall_half_width":{"label":"The walls below the round body down to the underside, half the width","kind":"length","measurements":[{"id":"model","value":0.453,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"as dovetail_foot_y: planar faces z ±0.453 from y 0.250 to 0.458 (inside ±0.251)","via":"user"}}]},"gas_tube_hole_d":{"label":"The gas tube's hole through the front wall","kind":"length","measurements":[{"id":"tdp","value":0.1835,"unit":"in","pm":0.0015,"stated":".182 +.003 ∅ THRU; .781 ± .005","source":{"type":"standard","doc":"US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-3/3, front view; user-supplied scan (Distribution Statement F), PDF page 126","via":"user"}}]},"gas_tube_hole_above_bore":{"label":"The gas tube's hole above the bore's axis","kind":"length","measurements":[{"id":"tdp","value":0.781,"unit":"in","pm":0.005,"stated":".781 ± .005","source":{"type":"standard","doc":"US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-3/3, front view; user-supplied scan (Distribution Statement F), PDF page 126","via":"user"}}]},"gas_tube_lobe_r":{"label":"The gas tube's hole, its four lobes' radius","kind":"length","measurements":[{"id":"tdp","value":0.047,"unit":"in","pm":0.005,"stated":".042 +.010 R 4 PLACES EQL SP RANDOM ORIENTATION EXCEPT MUST NOT INTERSECT THREADS","source":{"type":"standard","doc":"US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-3/3, front view; user-supplied scan (Distribution Statement F), PDF page 126","via":"user"},"note":"BCM's photo of the front end shows the four lobes under its BCM4 mark, set on the diagonals."}]},"gas_tube_lobe_offset":{"label":"The four lobes' centres from the hole's centre","kind":"length","measurements":[{"id":"model","value":0.11,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/batch123/bcm-m4-upper/cad_ch.py): four cylinders r .045 about (y 1.585 and 1.740, z ±0.078) round the hole's own at (y 1.662, z 0): 0.110 off its centre, on the diagonals","via":"user"}}]},"thread_major_d":{"label":"The barrel-nut thread's major diameter (1 1/4-18 UNEF-2A, after anodize)","kind":"length","measurements":[{"id":"tdp","value":1.244,"unit":"in","pm":0.0045,"stated":"1.250 -18 UNEF-2A: MAJOR ∅ 1.2485 – 1.2398 AFTER COATING","source":{"type":"standard","doc":"US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-1/3, Detail C; user-supplied scan (Distribution Statement F), PDF page 123","via":"user"},"note":"The side photo's thread reads 1.19 to 1.21 crest to crest: thin crests on white are eaten by the background's bloom, so it isn't a check."}]},"thread_minor_d":{"label":"The barrel-nut thread's minor diameter","kind":"length","measurements":[{"id":"tdp","value":1.1803,"unit":"in","pm":0.003,"stated":"MINOR ∅ 1.1803 MAX AFTER COATING","source":{"type":"standard","doc":"US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-1/3, Detail C; user-supplied scan (Distribution Statement F), PDF page 123","via":"user"},"note":"A maximum: the roots are drawn at it."}]},"thread_pitch":{"label":"The barrel-nut thread's pitch (18 to the inch)","kind":"length","measurements":[{"id":"tdp","value":0.0556,"unit":"in","pm":0.0001,"stated":"1.250 -18 UNEF-2A","source":{"type":"standard","doc":"US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-1/3, Detail C; user-supplied scan (Distribution Statement F), PDF page 123","via":"user"},"note":"1/18 in."}]},"index_notch_width":{"label":"The barrel's index pin's notch in the thread, width","kind":"length","measurements":[{"id":"tdp","value":0.127,"unit":"in","pm":0.001,"stated":".126 +.002","source":{"type":"standard","doc":"US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-2/3, plan view; user-supplied scan (Distribution Statement F), PDF page 124","via":"user"}}]},"index_notch_depth":{"label":"The index pin's notch, how far back from the front face","kind":"length","measurements":[{"id":"tdp","value":0.16,"unit":"in","pm":0.01,"stated":".15 +.02","source":{"type":"standard","doc":"US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-2/3, plan view; user-supplied scan (Distribution Statement F), PDF page 124","via":"user"}}]},"port_front_x":{"label":"The ejection port's front end at the outer surface (the front hinge lug's rear face), X","kind":"length","measurements":[{"id":"tdp","value":6.078,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{.front_face_x} - 1.00in + 0.042in","via":"user"},"note":"US Army TDP drawing 12576280, frame F-2/3, side elevation (PDF page 124): \"1.01 −.02\" and \".037 +.010\"."},{"id":"model","value":6.079,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/batch123/bcm-m4-upper/cad_ch.py): the hinge lugs' bores (r .0625 about y 0.641, z 0.689) end at x 2.932 and 6.079","via":"user"}},{"id":"right","value":6.11,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-m4-upper b896edc62dc6 (Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins: 127.86 px/in in the mid-plane; the lens about 38 in away over x 2.2","method":"the closed cover's front edge reads 6.176 and its rear edge 3.000 (0.6 nearer the lens: x 1.0167): 6.111 and 2.987, 3.124 apart (the cover is 3.130 by its drawing)","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing; the reference model has the same face within 0.001 and BCM's closed cover ends 0.03 ahead, within the photo's ±."},"note":"The M16A2's drawing takes 1.01 −.02 from the front face to the opening's inner front end, and ends the 3.120 +.010 slot .037 +.010 ahead of that. (The M16A1's has the same \"1.00\" and \".042\": the catalog's other forged upper reads the port's end at the 1.00, 0.04 behind this.)"},"port_length":{"label":"The ejection port's length at the outer surface (between the hinge lugs)","kind":"length","measurements":[{"id":"tdp","value":3.125,"unit":"in","pm":0.005,"stated":"3.120 +.010; 1.562 ± .010","source":{"type":"standard","doc":"US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-2/3, side elevation; user-supplied scan (Distribution Statement F), PDF page 124","via":"user"},"note":"The M16A1's 8448524 has it as 3.125."}]},"port_bottom_y":{"label":"The port's lower edge above the pin line, seen from the side","kind":"length","measurements":[{"id":"drawn","value":0.841,"unit":"in","pm":0.01,"source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G, side view, scaled (not a callout): its lower straight edge at px row 3640 against the lug holes' row 3900 at the sheet's own 309.3 px/in (the lug holes 6.375 apart); R .25 TRUE ends; references/tdp p108","via":"user"},"note":"As the catalog's other forged upper has it (its own photo, port open, read 0.834)."}]},"port_end_r":{"label":"The port's ends' radius (half its height from the side)","kind":"length","measurements":[{"id":"tdp","value":0.25,"unit":"in","pm":0.005,"stated":".25 R TRUE 2 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: side elevation; user-supplied scan, references/tdp p108","via":"user"},"note":"The M16A2's View F-F: (.24 R)."}]},"port_face_angle":{"label":"The port's face (the cover's seat), turned up from the side","kind":"angle","measurements":[{"id":"tdp","value":22.5,"unit":"deg","pm":1,"stated":"22° 30' ± 1° 0'","source":{"type":"standard","doc":"US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-3/3, Detail G; user-supplied scan (Distribution Statement F), PDF page 126","via":"user"}}]},"hinge_y":{"label":"The port cover's hinge pin, Y above the pin line","kind":"length","measurements":[{"id":"model","value":0.641,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/batch123/bcm-m4-upper/cad_ch.py): the hinge lugs' bores r .0625 about (y 0.641, z 0.689)","via":"user"}},{"id":"right","value":0.63,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-m4-upper b896edc62dc6 (Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins: 127.86 px/in in the mid-plane; the lens 4 to 5 in above the pin line, 35.5 to 38 in away","method":"the pin's end ahead of the front hinge lug, centred at px row 457.5: reads 0.542, 0.69 nearer the lens; through it 0.61 to 0.64","via":"harvest"}}],"adopt":{"from":"model","reason":"The model places the pin; BCM's reads the same through the photo's lens. (The M16A2's Detail G, read as .545 −.010 off the bore along the port's face's normal and .495 +.010 down it, gives 0.62.)"}},"hinge_z":{"label":"The port cover's hinge pin, out from the middle (Z)","kind":"length","measurements":[{"id":"model","value":0.689,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"as hinge_y","via":"user"}},{"id":"banner","value":0.66,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-m4-upper c6717b54ef96 (BCM's shop, the upper receivers category's banner: an M4 flat top with T-marks, forward assist and port door from straight above, 1200 x 400)","scaleRef":"the rail's 13 slots at std.picatinny.slot_pitch: 121.27 px/in at the rail's top; lower things read smaller about a point 1.5 in to the receiver's left (the body's two edges)","method":"the closed cover's outermost edge along the port, px row 141: 0.75 from the middle at the hinge's height, less the hinge's curl (.090: 8448785)","via":"harvest"}}],"adopt":{"from":"model","reason":"The model places the pin; BCM's from above reads 0.03 less, within its ±."}},"cover_length":{"label":"The port cover's length","kind":"length","measurements":[{"id":"tdp","value":3.13,"unit":"in","pm":0.005,"stated":"3.130 -A-","source":{"type":"standard","doc":"US Army TDP drawing 8448785 (Cover, Ejection Port), rev C (its application block lists the M4); user-supplied scan, PDF page 136","via":"user"}},{"id":"right","value":3.124,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-m4-upper b896edc62dc6 (Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins: 127.86 px/in in the mid-plane; 0.6 nearer the lens, 38 in away","method":"the closed cover's two ends 406 px apart (3.175), less the 1.67% its plane reads long","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing; BCM's cover reads the same within 0.006."}},"cover_height":{"label":"The port cover's height, its hinge's axis to its free edge","kind":"length","measurements":[{"id":"tdp","value":0.79,"unit":"in","pm":0.005,"stated":".790","source":{"type":"standard","doc":"US Army TDP drawing 8448785 (Cover, Ejection Port), rev C; user-supplied scan, PDF page 136","via":"user"}}]},"cover_thickness":{"label":"The port cover's sheet","kind":"length","measurements":[{"id":"tdp","value":0.025,"unit":"in","pm":0.0015,"stated":".0250 ± .0015 STOCK THICKNESS","source":{"type":"standard","doc":"US Army TDP drawing 8448785 (Cover, Ejection Port), rev C, Section C-C; user-supplied scan, PDF page 136","via":"user"}}]},"cover_bead_height":{"label":"The port cover's two beads, how far they stand off the sheet","kind":"length","measurements":[{"id":"tdp","value":0.05,"unit":"in","pm":0.005,"stated":".05, BOTH BEADS","source":{"type":"standard","doc":"US Army TDP drawing 8448785 (Cover, Ejection Port), rev C, Section C-C; user-supplied scan, PDF page 136","via":"user"}}]},"cover_corner_r":{"label":"The port cover's two free corners","kind":"length","measurements":[{"id":"tdp","value":0.25,"unit":"in","pm":0.005,"stated":".250 R, 2 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 8448785 (Cover, Ejection Port), rev C; user-supplied scan, PDF page 136","via":"user"}}]},"cover_hinge_curl_id":{"label":"The port cover's hinge curl, inside","kind":"length","measurements":[{"id":"tdp","value":0.13,"unit":"in","pm":0.003,"stated":".130 DIA -B-","source":{"type":"standard","doc":"US Army TDP drawing 8448785 (Cover, Ejection Port), rev C, Section C-C; user-supplied scan, PDF page 136","via":"user"}}]},"cover_body_length":{"label":"The port cover's sheet between its hinge knuckles' ends (its beads are set out from it)","kind":"length","measurements":[{"id":"tdp","value":3.1,"unit":"in","pm":0.005,"stated":"3.100","source":{"type":"standard","doc":"US Army TDP drawing 8448785 (Cover, Ejection Port), rev C; user-supplied scan, PDF page 136","via":"user"}}]},"cover_bead_leg_spacing":{"label":"Each bead's two legs, centre to centre","kind":"length","measurements":[{"id":"tdp","value":1.115,"unit":"in","pm":0.005,"stated":"1.115 2 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 8448785 (Cover, Ejection Port), rev C; user-supplied scan, PDF page 136","via":"user"}}]},"cover_bead_gap":{"label":"The two beads' inner legs, centre to centre (the latch housing between them)","kind":"length","measurements":[{"id":"tdp","value":0.62,"unit":"in","pm":0.005,"stated":".620","source":{"type":"standard","doc":"US Army TDP drawing 8448785 (Cover, Ejection Port), rev C; user-supplied scan, PDF page 136","via":"user"}}]},"cover_bead_inset":{"label":"The beads' inset: their tops below the cover's free edge, their legs' ends above the hinge's line","kind":"length","measurements":[{"id":"tdp","value":0.12,"unit":"in","pm":0.01,"stated":".12, 2 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 8448785 (Cover, Ejection Port), rev C; user-supplied scan, PDF page 136","via":"user"},"note":"Called out twice, once at each end of the legs; read as both insets."}]},"cover_bead_corner_r":{"label":"The beads' corners (their centre line)","kind":"length","measurements":[{"id":"tdp","value":0.125,"unit":"in","pm":0.005,"stated":".125 R, 4 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 8448785 (Cover, Ejection Port), rev C; user-supplied scan, PDF page 136","via":"user"}}]},"cover_bead_r":{"label":"The beads' section, the radius inside the pressed sheet","kind":"length","measurements":[{"id":"tdp","value":0.025,"unit":"in","pm":0.005,"stated":".025R, BOTH BEADS","source":{"type":"standard","doc":"US Army TDP drawing 8448785 (Cover, Ejection Port), rev C; user-supplied scan, PDF page 136, Section C-C","via":"user"}}]},"cover_seat_below_hinge":{"label":"The cover's seat on the receiver, below the hinge pin's centre along the port's face's normal","kind":"length","measurements":[{"id":"tdp","value":0.04,"unit":"in","pm":0.005,"stated":".040 ± .005 2 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-3/3, Detail G; user-supplied scan (Distribution Statement F), PDF page 126","via":"user"},"note":"Read as from the hinge holes' centre to the cutter's surface the cover lies on."}]},"hinge_lug_r":{"label":"The two hinge lugs' radius about the pin","kind":"length","measurements":[{"id":"model","value":0.1365,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/batch123/bcm-m4-upper/cad_ch.py): cylinders r .1365 about (y 0.641, z 0.689) over x 2.837 to 2.932 and 6.079 to 6.235","via":"user"}}]},"hinge_lug_rear_x":{"label":"The rear hinge lug's rear end, X","kind":"length","measurements":[{"id":"model","value":2.806,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"as hinge_lug_r: the pin's bore (r .0625) runs from x 2.806 to 2.932","via":"user"}}]},"hinge_lug_front_x":{"label":"The front hinge lug's front end, X","kind":"length","measurements":[{"id":"model","value":6.235,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"as hinge_lug_r: the pin's bore runs from x 6.079 to 6.235","via":"user"}}]},"hinge_pin_front_x":{"label":"The hinge pin's front end, X","kind":"length","measurements":[{"id":"right","value":6.6,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-m4-upper b896edc62dc6 (Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins: 127.86 px/in in the mid-plane; 0.69 nearer the lens, 38 in away over x 2.2","method":"the pin's end ahead of the front hinge lug at px 1021 (6.68), through the lens","via":"harvest"}}]},"hinge_pin_rear_x":{"label":"The hinge pin's rear end, X","kind":"length","measurements":[{"id":"right","value":2.83,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-m4-upper b896edc62dc6 (Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins: 127.86 px/in in the mid-plane; 0.69 nearer the lens, 38 in away over x 2.2","method":"the pin's head behind the rear hinge lug at px 530 (2.836), through the lens","via":"harvest"}}]},"cover_latch_width":{"label":"The port cover's latch housing, along the cover","kind":"length","measurements":[{"id":"right","value":0.45,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-m4-upper b896edc62dc6 (Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins: 127.86 px/in in the mid-plane; 0.55 nearer the lens, 38 in away","method":"the square boss at the cover's middle, px 725 to 783 (0.454), less the 1.5% its plane reads long; it is as tall as wide (px rows 368 to 425)","via":"harvest"},"note":"The cover's drawing leaves .433 +.004 between its beads for it."}]},"cover_latch_proud":{"label":"The latch housing, how far it stands off the cover","kind":"length","measurements":[],"note":"No view on file gives it a size: the housing's own drawing (8448784) wasn't read. Drawn at the beads' height until it is."},"fa_axis_angle":{"label":"The forward assist's axis, turned inward toward the front in plan","kind":"angle","measurements":[{"id":"tdp","value":20,"unit":"deg","pm":1,"stated":"20° ± 1°","source":{"type":"standard","doc":"US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-2/3, plan view; user-supplied scan (Distribution Statement F), PDF page 124","via":"user"}},{"id":"banner","value":20.1,"unit":"deg","pm":1,"source":{"type":"photo","photo":"references/bcm-m4-upper c6717b54ef96 (BCM's shop, the upper receivers category's banner: an M4 flat top with T-marks, forward assist and port door from straight above, 1200 x 400)","scaleRef":"the rail's 13 slots at std.picatinny.slot_pitch: 121.27 px/in at the rail's top","method":"the housing's outer edge over px 820 to 1020, 9 px in every 25 (19.8° on the photo; 20.1° with lower things read through the lens); its cap's rim stands 20.6° off square","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing; BCM's part from above reads the same."}},"fa_mouth_z":{"label":"The forward assist's bore, its mouth's centre out from the middle (Z)","kind":"length","measurements":[{"id":"tdp","value":1.0285,"unit":"in","pm":0.005,"stated":"1.0285 ± .0050","source":{"type":"standard","doc":"US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-2/3, plan view; user-supplied scan (Distribution Statement F), PDF page 124","via":"user"},"note":"Read as the line the 20° is struck from: the bore's centre where it leaves the housing's rear face."},{"id":"banner","value":1.045,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-m4-upper c6717b54ef96 (BCM's shop, the upper receivers category's banner: an M4 flat top with T-marks, forward assist and port door from straight above, 1200 x 400)","scaleRef":"the rail's 13 slots at std.picatinny.slot_pitch: 121.27 px/in at the rail's top; 118.2 px/in at the bore's height (the cap's .605 rim: 71.5 px)","method":"where the cap's stem leaves the housing's rear face, px (1053, 102 to 106): 1.03 to 1.06","via":"harvest"}},{"id":"model","value":1.09,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text (the 2026-10-03 research pass, .cache/research/aero-upper/REPORT.md): the bore's axis through (-0.395, 0.879, 1.090), turned 22.5°","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's callout, which BCM's part from above agrees with; the reference model stands 0.06 further out (and is turned 22.5°, not 20)."}},"fa_mouth_x":{"label":"The forward assist's bore, its mouth's centre, X","kind":"length","measurements":[{"id":"banner","value":-0.44,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-m4-upper c6717b54ef96 (BCM's shop, the upper receivers category's banner: an M4 flat top with T-marks, forward assist and port door from straight above, 1200 x 400)","scaleRef":"the rail's 13 slots at std.picatinny.slot_pitch: 121.27 px/in at the rail's top, the rearmost slot's centre at px 842.0 as rail_slot0_x; lower things read 2.5% smaller about a point near the receiver's rear end (its rear face reads where the drawing has it only with the lens there)","method":"where the cap's stem leaves the housing's rear face, px 1054: 0.432 behind the takedown pin at the rail's scale, -0.438 through the lens; the ± is the lens's place along the receiver","via":"harvest"}},{"id":"drawn","value":-0.43,"unit":"in","pm":0.04,"source":{"type":"standard","doc":"US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-2/3, plan view, scaled (not a callout): the bore's centre line crosses the 1.0285 line 0.19 ahead of the rear face at the sheet's 245 px/in; user-supplied scan, PDF page 124","via":"user"}}],"adopt":{"from":"banner","reason":"BCM's own part; the drawing, scaled, agrees within 0.01."}},"fa_bore_d":{"label":"The forward assist's bore","kind":"length","measurements":[{"id":"tdp","value":0.509,"unit":"in","pm":0.003,"stated":".506 +.006 ∅ TO DEPTH SHOWN","source":{"type":"standard","doc":"US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-2/3, plan view; user-supplied scan (Distribution Statement F), PDF page 124","via":"user"},"note":"The M16A1's 8448524: .509 DIA ± .003."}]},"fa_bore_depth":{"label":"The forward assist's bore, its depth from the mouth","kind":"length","measurements":[{"id":"tdp","value":0.65,"unit":"in","pm":0.01,"stated":".65 ± .01","source":{"type":"standard","doc":"US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-2/3, plan view; user-supplied scan (Distribution Statement F), PDF page 124","via":"user"},"note":"Read as the full bore's depth along its axis from the housing's rear face."}]},"fa_housing_r":{"label":"The forward assist housing's radius about its axis","kind":"length","measurements":[{"id":"banner","value":0.305,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-m4-upper c6717b54ef96 (BCM's shop, the upper receivers category's banner: an M4 flat top with T-marks, forward assist and port door from straight above, 1200 x 400)","scaleRef":"the rail's 13 slots at std.picatinny.slot_pitch: 121.27 px/in at the rail's top; 118.2 px/in at the bore's height","method":"the housing's outer edge (a straight line over 200 px, 20° off the receiver's) stands 1.370 from the middle at the mouth: 0.32 square off the axis by the drawing's mouth (1.0285), 0.29 by the photo's own (1.06)","via":"harvest"}},{"id":"right","value":0.285,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/bcm-m4-upper b896edc62dc6 (Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins: 127.86 px/in in the mid-plane; about 1.1 nearer the lens, 38 in away (the ± is that depth, 0.9 to 1.4)","method":"the housing's lit bar from the right, 75 px tall (0.587), less the 3% its depth reads large: 0.57 across","via":"harvest"}},{"id":"model","value":0.3125,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text (the 2026-10-03 research pass): the housing's cylinder r .3125 on the bore's axis","via":"user"}}],"adopt":{"from":"banner","reason":"BCM's part from above, between the side photo's reading and the reference model's: the three span 0.03."}},"fa_cap_head_d":{"label":"The forward assist's cap, its head","kind":"length","measurements":[{"id":"tdp","value":0.605,"unit":"in","pm":0.005,"stated":".610 −.010 ∅","source":{"type":"standard","doc":"US Army TDP drawing 9349084 (Cap, Plunger), rev H (its application block lists the M4 through 9349085); user-supplied scan (Distribution Statement F), PDF page 151","via":"user"}}]},"fa_cap_body_d":{"label":"The forward assist's cap, its body","kind":"length","measurements":[{"id":"tdp","value":0.486,"unit":"in","pm":0.004,"stated":".490 −.008 ∅ -A-","source":{"type":"standard","doc":"US Army TDP drawing 9349084 (Cap, Plunger), rev H; user-supplied scan (Distribution Statement F), PDF page 151","via":"user"}}]},"fa_cap_length":{"label":"The forward assist's cap, end to end","kind":"length","measurements":[{"id":"tdp","value":0.71,"unit":"in","pm":0.005,"stated":".715 −.010","source":{"type":"standard","doc":"US Army TDP drawing 9349084 (Cap, Plunger), rev H; user-supplied scan (Distribution Statement F), PDF page 151","via":"user"}}]},"fa_cap_body_length":{"label":"The forward assist's cap, its straight body (the rest is the head's 20° flare)","kind":"length","measurements":[{"id":"tdp","value":0.57,"unit":"in","pm":0.005,"stated":".565 +.010; 20° ± 1°","source":{"type":"standard","doc":"US Army TDP drawing 9349084 (Cap, Plunger), rev H, Section A-A; user-supplied scan (Distribution Statement F), PDF page 151","via":"user"}}]},"fa_cap_proud":{"label":"The forward assist's cap at rest, its rear face behind the housing's (along the axis)","kind":"length","measurements":[{"id":"banner","value":0.5,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/bcm-m4-upper c6717b54ef96 (BCM's shop, the upper receivers category's banner: an M4 flat top with T-marks, forward assist and port door from straight above, 1200 x 400)","scaleRef":"the cap's own rim, .605 across (9349084): 71.5 px, 118.2 px/in","method":"from where the stem leaves the housing (px 1054, 102) to the middle of the rim's thickness (px 1104.5, 85.5): 53 px, 0.449, and half the rim's 0.11","via":"harvest"}},{"id":"right","value":0.47,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/bcm-m4-upper b896edc62dc6 (Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins: 127.86 px/in in the mid-plane; 1.2 to 1.5 nearer the lens, 38 in away","method":"the cap's rearmost point reads -1.145 (its rim's near edge, 0.10 behind its face's centre for the 20° turn) against the housing's rear rim at -0.527: through the lens -1.03 and -0.44, 0.59 apart along x, less the rim's 0.10, over cos 20°","via":"harvest"}}],"adopt":{"from":"banner","reason":"The view that sees the cap along its own axis; the side photo agrees within its ±."}},"deflector_rear_x":{"label":"The deflector's rear face at the body, X","kind":"length","measurements":[{"id":"banner","value":2.075,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-m4-upper c6717b54ef96 (BCM's shop, the upper receivers category's banner: an M4 flat top with T-marks, forward assist and port door from straight above, 1200 x 400)","scaleRef":"the rail's 13 slots at std.picatinny.slot_pitch: 121.27 px/in at the rail's top, the rearmost slot's centre at px 842.0 as rail_slot0_x; lower things read 2% smaller about a point near the receiver's rear end","method":"the rear face's foot at px 755","via":"harvest"}},{"id":"right","value":2.04,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-m4-upper b896edc62dc6 (Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins: 127.86 px/in in the mid-plane; the lens over x 2.2 (so nothing to correct here)","method":"the rear face's fold against the body, px 428","via":"harvest"}},{"id":"model","value":2.06,"unit":"in","pm":0.02,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text (the 2026-10-03 research pass): the deflector's faces over x 2.06 to 2.99, y 0.95 to 1.70, reaching z 1.20 to 1.30","via":"user"}}],"adopt":{"from":"model","reason":"Between BCM's two photos, which read 0.035 apart, and within each one's ±."}},"deflector_front_x":{"label":"The deflector's front face, where it runs out into the body, X","kind":"length","measurements":[{"id":"banner","value":2.97,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-m4-upper c6717b54ef96 (BCM's shop, the upper receivers category's banner: an M4 flat top with T-marks, forward assist and port door from straight above, 1200 x 400)","scaleRef":"the rail's 13 slots at std.picatinny.slot_pitch: 121.27 px/in at the rail's top, the rearmost slot's centre at px 842.0 as rail_slot0_x; lower things read 2% smaller about a point near the receiver's rear end","method":"the front face's foot at px 648","via":"harvest"}},{"id":"right","value":2.97,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-m4-upper b896edc62dc6 (Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins: 127.86 px/in in the mid-plane; the lens over x 2.2, 38 in away","method":"its lit face ends beside the cover's rear edge, px 548 (2.977), 0.6 nearer the lens","via":"harvest"}}],"adopt":{"from":"banner","reason":"Both of BCM's photos give the same figure (the reference model: 2.99)."}},"deflector_tip_x":{"label":"The deflector's outer ridge, X","kind":"length","measurements":[{"id":"banner","value":2.4,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-m4-upper c6717b54ef96 (BCM's shop, the upper receivers category's banner: an M4 flat top with T-marks, forward assist and port door from straight above, 1200 x 400)","scaleRef":"the rail's 13 slots at std.picatinny.slot_pitch: 121.27 px/in at the rail's top, the rearmost slot's centre at px 842.0 as rail_slot0_x; lower things read 2% smaller about a point near the receiver's rear end","method":"the rounded tip at px 712 to 722","via":"harvest"}},{"id":"right","value":2.44,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-m4-upper b896edc62dc6 (Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins: 127.86 px/in in the mid-plane; the lens over x 2.2, 38 in away","method":"the bright edge between its two faces, px 478 to 485 (2.453), 1.26 nearer the lens","via":"harvest"}}],"adopt":{"from":"banner","reason":"The view that sees the ridge's reach; the side photo reads 0.04 more, within their ±."}},"deflector_out":{"label":"The deflector's reach out from the middle (Z)","kind":"length","measurements":[{"id":"banner","value":1.26,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-m4-upper c6717b54ef96 (BCM's shop, the upper receivers category's banner: an M4 flat top with T-marks, forward assist and port door from straight above, 1200 x 400)","scaleRef":"the rail's 13 slots at std.picatinny.slot_pitch: 121.27 px/in at the rail's top; lower things read smaller about a point 1.5 in to the receiver's left (the body's two edges, which that makes 0.60 either side)","method":"the tip at px row 77: 1.24 to 1.28 from the middle as its height is taken from 1.5 down to 0.9","via":"harvest"}},{"id":"model","value":1.25,"unit":"in","pm":0.05,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text (the 2026-10-03 research pass): the deflector's faces reach z 1.20 to 1.30","via":"user"}}],"adopt":{"from":"banner","reason":"BCM's own part; the reference model agrees."}},"deflector_top_y":{"label":"The deflector's top at the body, Y above the pin line","kind":"length","measurements":[{"id":"right","value":1.72,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-m4-upper b896edc62dc6 (Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins: 127.86 px/in in the mid-plane; the lens 4 to 5 in above the pin line, about 38 in away","method":"its top edge at px row 315 reads 1.657, 0.6 to 0.9 nearer the lens: 0.06 more through it","via":"harvest"}},{"id":"model","value":1.7,"unit":"in","pm":0.02,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text (the 2026-10-03 research pass): the deflector's faces over y 0.95 to 1.70","via":"user"}}],"adopt":{"from":"model","reason":"The model's figure, which BCM's photo gives within its ± once read through its lens."}},"deflector_bottom_y":{"label":"The deflector's foot at the body, Y above the pin line","kind":"length","measurements":[{"id":"right","value":1,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-m4-upper b896edc62dc6 (Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins: 127.86 px/in in the mid-plane; the lens 4 to 5 in above the pin line, about 38 in away","method":"its lower edge at px row 408 reads 0.929, 0.65 nearer the lens: 0.07 more through it","via":"harvest"}},{"id":"model","value":0.95,"unit":"in","pm":0.02,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"as deflector_top_y","via":"user"}}],"adopt":{"from":"model","reason":"As deflector_top_y: the photo agrees within its ±."}},"deflector_ridge_top_y":{"label":"The deflector's outer ridge, its top, Y above the pin line","kind":"length","measurements":[{"id":"right","value":1.67,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/bcm-m4-upper b896edc62dc6 (Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins: 127.86 px/in in the mid-plane; the lens 4 to 5 in above the pin line, about 38 in away","method":"the bright edge between its faces runs from px row 328 to 400 (1.555 down to 0.992), 1.26 nearer the lens: 0.12 more through it","via":"harvest"}}]},"deflector_ridge_bottom_y":{"label":"The deflector's outer ridge, its foot, Y above the pin line","kind":"length","measurements":[{"id":"right","value":1.11,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/bcm-m4-upper b896edc62dc6 (Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins: 127.86 px/in in the mid-plane; the lens 4 to 5 in above the pin line, about 38 in away","method":"as deflector_ridge_top_y: the edge's lower end","via":"harvest"}}]},"left_pad_front_x":{"label":"The raised band low on the left wall, its front end, X","kind":"length","measurements":[{"id":"left","value":6.105,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-m4-upper b3b8d1ad9d16 (Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 137.71 px/in in the mid-plane, the takedown hole at (997.82, 549.45) px; the lens 35 in away, 3.3 in above the pin line over x 3.9 (left_photo_lens_*). Checked beside it: the underside under the band reads at row 522.3 for the 521.7 the lens puts the deck's 0.2485 at on a face 0.527 out","method":"rows 476, 482 and 490: the tone falls from 38, 41 and 35 at column 150 to 23, 26 and 25 at column 155 and stays (the band's own tone, 23 to 35): 152.5 px, 6.138 in the mid-plane, 6.105 through the lens on a face 0.527 out. It begins at the pivot lug's rear edge, with no lit line: its front end is in shadow","via":"harvest"}}],"note":"An upright flat along the foot of the left wall, from the deck up to an edge on the round body, darker than the body over it and than the wall behind it. Raised, not sunk, on three counts: its rear end shows as a lit face leaning rearward, from a line at column 590 to a foot that is under it at row 476 and 11 px behind it from row 498 down, which is the round body falling away behind a flat face down to the lug wall's crease and the wall's flat below; its underside reads a pixel lower in the picture than the wall's behind it (row 522.3 against 521.0), as a face 0.07 in nearer a lens 3.3 in above does (0.9 px); and the cam pin's pad over it, which the reference model has raised, is lit at the same end. How far it stands out is in no view: the script takes its face to stand where the body as drawn is at its upper edge's height (0.527 off the middle, 0.074 out from the lug wall), and its rear end then leans 43 degrees."},"left_pad_rear_x":{"label":"The raised band low on the left wall, its face's rear edge, X","kind":"length","measurements":[{"id":"left","value":2.975,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bcm-m4-upper b3b8d1ad9d16 (Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 137.71 px/in in the mid-plane, the takedown hole at (997.82, 549.45) px; the lens 35 in away, 3.3 in above the pin line over x 3.9 (left_photo_lens_*). Checked beside it: the underside under the band reads at row 522.3 for the 521.7 the lens puts the deck's 0.2485 at on a face 0.527 out","method":"rows 476 to 520: a lit line a pixel or two wide at column 590 (82, 97, 95, 95, 97, 99, 97, 100, 102, 104 at rows 476 to 520, against 33 to 46 at column 585 on the band): 590 px, 2.961 in the mid-plane, 2.975 through the lens on a face 0.527 out","via":"harvest"}}]},"left_pad_rear_foot_x":{"label":"The raised band low on the left wall, the foot of its rear end on the wall behind it, X","kind":"length","measurements":[{"id":"left","value":2.895,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bcm-m4-upper b3b8d1ad9d16 (Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 137.71 px/in in the mid-plane, the takedown hole at (997.82, 549.45) px; the lens 35 in away, 3.3 in above the pin line over x 3.9 (left_photo_lens_*). Checked beside it: the underside under the band reads at row 522.3 for the 521.7 the lens puts the deck's 0.2485 at on a face 0.527 out","method":"rows 498 to 520: a second lit line at columns 600 to 602 (92, 96, 98, 104, 111, 110 at column 600, 55 to 58 at 605, 45 to 61 between the two lines at 595); above row 498 it closes on the first and meets it at row 476, where the band's upper edge is: 601 px, 2.882 in the mid-plane, 2.895 through the lens on the lug wall, 0.453 out","via":"harvest"}}]},"left_pad_top_y":{"label":"The raised band low on the left wall, its upper edge above the pin line","kind":"length","measurements":[{"id":"left","value":0.601,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bcm-m4-upper b3b8d1ad9d16 (Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 137.71 px/in in the mid-plane, the takedown hole at (997.82, 549.45) px; the lens 35 in away, 3.3 in above the pin line over x 3.9 (left_photo_lens_*). Checked beside it: the underside under the band reads at row 522.3 for the 521.7 the lens puts the deck's 0.2485 at on a face 0.527 out","method":"columns 158, 170, 250, 330, 420, 500 and 560: the body's tone over it (41 to 45 at row 470) falls to the band's (23 to 35 by row 476), at half its fall at rows 472.0, 472.9, 472.0, 472.2, 472.3, 471.5 and 472.2: 472.3 px, 0.560 above the pin line in the mid-plane, 0.601 through the lens on a face 0.527 out. Level end to end within a pixel","via":"harvest"}}],"note":"Behind the band the round body meets the lug wall's flat at rows 496 to 498 (columns 625, 700, 800): 0.42 above the pin line through the lens, for the 0.49 the section as drawn has that crease at (the round of body_radius about the bore meeting lug_wall_half_width). The body's section below the bore is the reference model's and isn't read on BCM's part; it is left as it is."},"left_tab_front_x":{"label":"The tab on the raised band, its front end, X","kind":"length","measurements":[{"id":"left","value":4.57,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-m4-upper b3b8d1ad9d16 (Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 137.71 px/in in the mid-plane, the takedown hole at (997.82, 549.45) px; the lens 35 in away, 3.3 in above the pin line over x 3.9 (left_photo_lens_*). Checked beside it: the underside under the band reads at row 522.3 for the 521.7 the lens puts the deck's 0.2485 at on a face 0.527 out","method":"rows 506, 510 and 518: the band's 34 to 39 rises to the tab's 40 to 45 between columns 365 and 375 (row 518's lit lower edge begins at 365: 39, 64): 367 px ± 4, 4.581 in the mid-plane, 4.570 through the lens. A soft beginning: drawn square","via":"harvest"}}],"note":"A low lump on the band's foot, under the cam pin's pad: lighter than the band (40 to 47 for its 32 to 36), its upper face lit and leaning, a lit line along its lower edge at row 518, and a lit end leaning rearward as the band's own is. Its underside reads a pixel lower than the band's (row 524 is 231 to 241 under it and 248 to 252 elsewhere), as a face nearer the lens does. How far it stands off the band is in no view: the script takes its rear end to lean as the band's own rear end does as drawn, which puts its face 0.059 off the band's, inside the body's widest."},"left_tab_rear_x":{"label":"The tab on the raised band, its face's rear edge, X","kind":"length","measurements":[{"id":"left","value":3.962,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bcm-m4-upper b3b8d1ad9d16 (Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 137.71 px/in in the mid-plane, the takedown hole at (997.82, 549.45) px; the lens 35 in away, 3.3 in above the pin line over x 3.9 (left_photo_lens_*). Checked beside it: the underside under the band reads at row 522.3 for the 521.7 the lens puts the deck's 0.2485 at on a face 0.527 out","method":"rows 513 to 522: the lit end begins at column 452 (row 516: 43 at 450, 120 at 455; row 518: 59, 128; row 520: 70, 120): 452 px, 3.964 in the mid-plane, 3.962 through the lens (it stands almost under the lens, 3.9)","via":"harvest"}}]},"left_tab_rear_foot_x":{"label":"The tab on the raised band, the foot of its rear end on the band, X","kind":"length","measurements":[{"id":"left","value":3.898,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bcm-m4-upper b3b8d1ad9d16 (Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 137.71 px/in in the mid-plane, the takedown hole at (997.82, 549.45) px; the lens 35 in away, 3.3 in above the pin line over x 3.9 (left_photo_lens_*). Checked beside it: the underside under the band reads at row 522.3 for the 521.7 the lens puts the deck's 0.2485 at on a face 0.527 out","method":"rows 518 to 522: the lit end reaches column 461 at its foot (row 518: 81 at 460, 51 at 465; row 520: 113 at 460, 48 at 465) and narrows upward to nothing at row 513, column 455: 461 px, 3.898 in the mid-plane and through the lens alike. A face square to the receiver would not show from a lens over x 3.9: it leans","via":"harvest"}}]},"left_tab_top_y":{"label":"The tab on the raised band, where its upper face leaves the band, above the pin line","kind":"length","measurements":[{"id":"left","value":0.368,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bcm-m4-upper b3b8d1ad9d16 (Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 137.71 px/in in the mid-plane, the takedown hole at (997.82, 549.45) px; the lens 35 in away, 3.3 in above the pin line over x 3.9 (left_photo_lens_*). Checked beside it: the underside under the band reads at row 522.3 for the 521.7 the lens puts the deck's 0.2485 at on a face 0.527 out","method":"columns 380, 400, 420 and 440: the band's 34 to 36 begins to rise at rows 504 to 506 (36, 40, 42 at column 380; 35, 37, 40 at 400): 505 px, 0.323 above the pin line in the mid-plane, 0.368 through the lens on a face 0.527 out","via":"harvest"}}]},"left_tab_face_top_y":{"label":"The tab on the raised band, its outer face's upper edge above the pin line","kind":"length","measurements":[{"id":"left","value":0.316,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bcm-m4-upper b3b8d1ad9d16 (Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768)","scaleRef":"its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 137.71 px/in in the mid-plane, the takedown hole at (997.82, 549.45) px; the lens 35 in away, 3.3 in above the pin line over x 3.9 (left_photo_lens_*). Checked beside it: the underside under the band reads at row 522.3 for the 521.7 the lens puts the deck's 0.2485 at on a face 0.527 out","method":"columns 380, 400, 420 and 440: the lit upper face is brightest at row 512 (47, 48, 48, 44) and the face under it is 40 to 42 from row 514: 513 px, 0.265 above the pin line in the mid-plane, 0.316 through the lens on a face 0.586 out","via":"harvest"}}]}}},{"subject":"bcm-mcmr-10-handguard","title":"BCM MCMR-10 M-LOK Compatible Modular Rail (BCM-MCMR-10-556-BLK)","dimensions":{"weight":{"label":"Weight on the rifle (the handguard and its mounting hardware)","kind":"mass","measurements":[{"id":"sum","value":8.9,"unit":"oz","pm":0.1,"source":{"type":"derived","expr":"{.weight_handguard} + {.weight_hardware}","via":"harvest"}},{"id":"primary-arms","value":8.9,"unit":"oz","pm":0.05,"stated":"Weight 8.9 Oz","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Bravo Company Manufacturing MCMR Free Float AR-15 Handguard - M-LOK - 10\" (BCM-MCMR-10-556-BLK), specifications","url":"https://www.primaryarms.com/bcm-10-mlok-compatible-modular-rail-bcm-mcmr-10-556-blk","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"sum","reason":"The maker's two figures; the seller's one figure is their sum."},"note":"BCM gives the two apart; what goes on the rifle is both. Whether the steel barrel nut is in the 2.3 oz of hardware BCM doesn't say in so many words: Primary Arms' one figure for the product is their sum (and its page for the Flat Dark Earth one prints both \"6.6 oz weight\" in its text and \"Weight 8.9 oz.\" in its table)."},"weight_handguard":{"label":"Weight, the handguard alone","kind":"mass","measurements":[{"id":"bcm","value":6.6,"unit":"oz","pm":0.05,"stated":"Handguard alone weighs 6.6 oz","source":{"type":"spec","publisher":"manufacturer","name":"Bravo Company USA, BCM® MCMR-10 (M-LOK® Compatible* Modular Rail) (BCM-MCMR-10-556-BLK), Description","url":"https://bravocompanyusa.com/bcm-mcmr-10-m-lok-compatible-modular-rail/","retrieved":"2026-10-06","via":"harvest"}}]},"weight_hardware":{"label":"Weight, its mounting hardware","kind":"mass","measurements":[{"id":"bcm","value":2.3,"unit":"oz","pm":0.05,"stated":"Handguard mounting hardware 2.3 oz","source":{"type":"spec","publisher":"manufacturer","name":"Bravo Company USA, BCM® MCMR-10 (M-LOK® Compatible* Modular Rail) (BCM-MCMR-10-556-BLK), Description","url":"https://bravocompanyusa.com/bcm-mcmr-10-m-lok-compatible-modular-rail/","retrieved":"2026-10-06","via":"harvest"}}],"note":"The same 2.3 oz on every length's page: the manual's bill of materials (the barrel nut, two clamp blocks, the index plate and the two cross bolts) is the series'."},"length":{"label":"Length, end to end (the rear end to the tips of the flare)","kind":"length","measurements":[{"id":"bcm","value":10.5,"unit":"in","pm":0.05,"stated":"Actual length when measured to flare is 10.5\"","source":{"type":"spec","publisher":"manufacturer","name":"Bravo Company USA, BCM® MCMR-10 (M-LOK® Compatible* Modular Rail) (BCM-MCMR-10-556-BLK), Description","url":"https://bravocompanyusa.com/bcm-mcmr-10-m-lok-compatible-modular-rail/","retrieved":"2026-10-06","via":"harvest"}},{"id":"photo","value":10.48,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-mcmr-10-handguard 85d879b8ed8e (BCM's gallery for the Flat Dark Earth MCMR-10, MCMR_10_FDE: the handguard alone, its right side seen from about 18° above, 2000 x 1333)","scaleRef":"its own top rail's 25 slots at the Picatinny pitch (std.picatinny.slot_pitch): each column read as a rail coordinate between the slot centres; the side faces' M-LOK row (pitch 235.4 px for 40 mm) for what stands at their depth, k 1.0226","method":"the silhouette's two ends (px 212 and 1778) as rail coordinates -1.881 and 25.308, each brought to its true place about the image's centre: -1.578 and 25.010 pitches. BCM's photo of the black one 5336b2e8ad26 reads 10.51 and Dirty Bird's cf89eca1f81a 10.50 the same way (.cache/batch46/bcm-mcmr-10-handguard/ruler.py)","via":"harvest"}}],"adopt":{"from":"bcm","reason":"The maker's figure; three photos read within 0.02 of it, inside what its one decimal and their ± allow."},"note":"BCM's \"10\" is 10.5 in \"to flare\", which is the whole length: the side faces run forward into two flat tips (the flare), 0.4 in past the rail's last slot's centre. Primary Arms says what the \"10\" is: \"the listed 10-inch length refers to the top Picatinny rail section; the overall handguard measures slightly longer\" (rail_length). The photos read 10.48 to 10.51 at the scale of the side faces, where both ends are."},"rail_length":{"label":"Its top rail's length, end to end","kind":"length","measurements":[{"id":"primary-arms","value":10.3,"unit":"in","pm":0.05,"stated":"10.3\" top rail length; 10.5\" overall length","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Bravo Company Manufacturing MCMR Free Float AR-15 Handguard - M-LOK - 10\" (BCM-MCMR-10-556-BLK), description","url":"https://www.primaryarms.com/bcm-10-mlok-compatible-modular-rail-bcm-mcmr-10-556-blk","retrieved":"2026-10-06","via":"harvest"}},{"id":"photos","value":10.343,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.rail_slot0_from_rear} + ({.rail_slots} - 1) * {std.picatinny.slot_pitch} + {.rail_front_from_last_slot}","via":"harvest"}}],"adopt":{"from":"photos","reason":"Read on its own rail in three photos; the seller's figure has one decimal and is the same length within it."},"note":"What the \"10\" in its name is, by the one seller that says so. The photos have its rail 0.607 in behind its first slot's centre, 24 pitches, and 0.28 in ahead of its last: 10.34."},"width":{"label":"Width across the flats (3 to 9 o'clock)","kind":"length","measurements":[{"id":"bcm","value":1.5,"unit":"in","pm":0.05,"stated":"1.5\" Wide","source":{"type":"spec","publisher":"manufacturer","name":"Bravo Company USA, BCM® MCMR-10 (M-LOK® Compatible* Modular Rail) (BCM-MCMR-10-556-BLK), Description","url":"https://bravocompanyusa.com/bcm-mcmr-10-m-lok-compatible-modular-rail/","retrieved":"2026-10-06","via":"harvest"}}]},"height":{"label":"Height (the rail's top to the bottom flat)","kind":"length","measurements":[{"id":"family","value":1.944,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{bcm-mcmr-15-handguard.height}","via":"harvest"}}],"note":"Not published. The family's section: the 15's figure, read on the one level photo of an MCMR alone. On this length's own photo from 18.5° above, the silhouette is 2.09 in high at the rail's scale, where that section (the rail's top 1.20 above the bore, a regular octagon 1.5 across) seen from there is 2.08."},"inside_diameter":{"label":"Inside diameter","kind":"length","measurements":[{"id":"bcm","value":1.3,"unit":"in","pm":0.05,"stated":"1.3\" Inside Diameter","source":{"type":"spec","publisher":"manufacturer","name":"Bravo Company USA, BCM® MCMR-10 (M-LOK® Compatible* Modular Rail) (BCM-MCMR-10-556-BLK), Description","url":"https://bravocompanyusa.com/bcm-mcmr-10-m-lok-compatible-modular-rail/","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":1.3,"unit":"in","pm":0.005,"stated":"Inner Diameter 1.30 in","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Bravo Company Manufacturing MCMR Free Float AR-15 Handguard - M-LOK - 10\" (BCM-MCMR-10-556-BLK), specifications","url":"https://www.primaryarms.com/bcm-10-mlok-compatible-modular-rail-bcm-mcmr-10-556-blk","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"bcm","reason":"The maker's; the seller repeats it."},"note":"The round bore at its rear end, which goes over the barrel nut. Ahead of it the inside follows the outside (Rifle Supply's three-quarter view of this length's muzzle end, be5d8498a666, shows flat inner walls): the model takes 1.3 in across the inner flats."},"receiver_gap":{"label":"The gap left between its rear end and the upper receiver","kind":"length","measurements":[{"id":"family","value":0.0225,"unit":"in","pm":0.0175,"source":{"type":"derived","expr":"{bcm-mcmr-15-handguard.receiver_gap}","via":"harvest"}}],"note":"The series' installation manual (KMR-A, MCMR, QRF; the same file is linked from this length's Flat Dark Earth page): the 15's entry quotes its step 14, a gap of .005 to .040 in."},"rear_x":{"label":"Its rear end against the receiver's front face (negative: behind it)","kind":"length","measurements":[{"id":"derived","value":-0.4225,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"0in - {std.ar15.upper_barrel_thread_length} + {.receiver_gap}","via":"harvest"}},{"id":"installed","value":-0.422,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mcmr-10-handguard dd70623d783b (BCM's gallery for the complete upper BCM-URG-11-MCMR10, -2: its right side seen level, 1500 x 1000) and dde102d81277 (-3: its left side, 1499 x 1000)","scaleRef":"the receiver's two lug holes, std.ar15.pin_spacing apart: 69.89 and 66.04 px/in","method":"the handguard's rearmost rail slot's centre 7.217 and 7.224 in ahead of the takedown hole (0.185 ahead of the receiver's front face, std.ar15.upper_front_face_x, between the two), less this ledger's rail_slot0_from_rear (0.607, BCM's photo of the handguard alone) (.cache/batch46/bcm-mcmr-10-handguard/urg.py)","via":"harvest"},"note":"A check through two photos, each with its own ±."}],"adopt":{"from":"derived","reason":"BCM's own rule for where it stops; the photos of the complete upper put it within 0.01 in of that."},"note":"It slides back over its barrel nut to the receiver's front shoulder, where the barrel-nut thread begins (std.ar15.upper_barrel_thread_length behind the front face), less the gap BCM's manual asks for."},"barrel_max_od":{"label":"The largest barrel its barrel nut goes over","kind":"length","measurements":[{"id":"bcm","value":1,"unit":"in","pm":0.05,"stated":"The barrel nut will fit over all mil-spec diameter barrels (max of 1\")","source":{"type":"spec","publisher":"manufacturer","name":"Bravo Company USA, BCM® MCMR-10 (M-LOK® Compatible* Modular Rail) (BCM-MCMR-10-556-BLK), Description","url":"https://bravocompanyusa.com/bcm-mcmr-10-m-lok-compatible-modular-rail/","retrieved":"2026-10-06","via":"harvest"}}]},"rail_top_above_bore":{"label":"Its rail's top above the bore axis","kind":"length","measurements":[{"id":"family","value":1.2,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{bcm-mcmr-15-handguard.rail_top_above_bore}","via":"harvest"}}],"note":"The family's: the 15's figure (its tube is about the bore, its rail level with a mil-spec receiver's). On BCM's two photos of the 11.5 in upper with this length on it, its rail's tooth tops read 0.02 in under the receiver's on the right side (2.042 against 2.062 above the pin line, in a photo whose scale runs 2% short along the handguard) and level with it on the left (2.104 against 2.100)."},"rail_slots":{"label":"Slots in its top rail","kind":"count","measurements":[{"id":"photo","value":25,"unit":"count","source":{"type":"photo","photo":"references/bcm-mcmr-10-handguard 85d879b8ed8e (BCM's gallery for the Flat Dark Earth MCMR-10, MCMR_10_FDE: the handguard alone, its right side seen from about 18° above, 2000 x 1333)","scaleRef":"none: a count","method":"the notches between the teeth along the top edge, each 57.6 px from the next (57.3 to 57.8), at five depths under the tooth tops: 25; the same count on BCM's photo of the black one (5336b2e8ad26, 30.6 px apart) and Dirty Bird's (cf89eca1f81a, 29.3 px), and on BCM's two photos of the complete upper (dd70623d783b, dde102d81277). The marks in the black one's slots run T14 (rearmost) to T38 (the frontmost slot)","via":"harvest"}}]},"rail_slot0_from_rear":{"label":"Its rail's rearmost slot (its centre) ahead of its rear end","kind":"length","measurements":[{"id":"bcm-photo","value":0.607,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-mcmr-10-handguard 85d879b8ed8e (BCM's gallery for the Flat Dark Earth MCMR-10, MCMR_10_FDE: the handguard alone, its right side seen from about 18° above, 2000 x 1333)","scaleRef":"its own top rail's 25 slots at the Picatinny pitch (std.picatinny.slot_pitch): each column read as a rail coordinate between the slot centres","method":"the rear end of the rail's top edge (the first column whose silhouette top is within 4 px of the tooth tops, px 231.5): 1.541 pitches behind the first slot's centre (.cache/batch46/bcm-mcmr-10-handguard/railfront.py)","via":"harvest"}},{"id":"bcm-black-photo","value":0.638,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-mcmr-10-handguard 5336b2e8ad26 (BCM's gallery, BCM-MCMR-10-556-BLK-2: the black handguard alone above its hardware, its left side seen from about 19° above, 1337 x 1000)","scaleRef":"its own top rail's 25 slots at the Picatinny pitch (std.picatinny.slot_pitch): each column read as a rail coordinate between the slot centres","method":"the same edge (mirrored px 265.5): 1.620 pitches behind the first slot's centre, at 78 px/in, where 4 px is 0.05 in of the rail's rounded rear corner","via":"harvest"}},{"id":"dirty-bird-photo","value":0.633,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-mcmr-10-handguard cf89eca1f81a (Dirty Bird's gallery, the 10 in black: its left side from about 19° above, 956 x 993)","scaleRef":"its own top rail's 25 slots at the Picatinny pitch (std.picatinny.slot_pitch): each column read as a rail coordinate between the slot centres","method":"the same edge (mirrored px 86.5): 1.606 pitches behind the first slot's centre, at 74 px/in","via":"harvest"}}],"adopt":{"from":"bcm-photo","reason":"The maker's own photograph at twice the scale of the other two, which read 0.03 more with the same 4 px of the corner taken in; with it the slot stands where the complete upper's photos have it (rail_slot0_x)."},"note":"Read to the rail's own rear end, along the far edge of its top, which is where the slots are read: nothing to bring to another depth. The body's rear end (the side face's, brought to its depth) reads 0.622 behind the slot in the same photo. The 15's is 0.623: one clamp end."},"rail_slot0_x":{"label":"Its rail's rearmost slot (its centre) ahead of the receiver's front face","kind":"length","measurements":[{"id":"installed","value":0.185,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-mcmr-10-handguard dd70623d783b (BCM's gallery for the complete upper BCM-URG-11-MCMR10, -2: its right side seen level, 1500 x 1000) and dde102d81277 (-3: its left side, 1499 x 1000)","scaleRef":"the receiver's two lug holes, std.ar15.pin_spacing apart: 69.89 and 66.04 px/in; the receiver's own 13 rail slots read 0.3936 and 0.3953 a pitch on them","method":"the gaps between the teeth 0.04 to 0.08 in below the tooth tops, each edge at the 50% level: the handguard's first slot's centre 7.217 in ahead of the takedown hole on the right photo and 7.224 on the left, less the receiver's front face (std.ar15.upper_front_face_x, 7.036): 0.181 and 0.188. It is 1.168 and 1.189 in ahead of the receiver's last slot: three pitches (.cache/batch46/bcm-mcmr-10-handguard/urg.py)","via":"harvest"}},{"id":"through-rear","value":0.1845,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.rear_x} + {.rail_slot0_from_rear}","via":"harvest"}}],"adopt":{"from":"installed","reason":"Read where it matters, in the receiver's own frame on two photos; the other goes through the handguard's rear end, which the gap at the receiver moves, and lands on it."}},"rail_front_from_last_slot":{"label":"Its rail's front end ahead of its last slot's centre","kind":"length","measurements":[{"id":"photo","value":0.28,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bcm-mcmr-10-handguard 85d879b8ed8e (BCM's gallery for the Flat Dark Earth MCMR-10, MCMR_10_FDE: the handguard alone, its right side seen from about 18° above, 2000 x 1333)","scaleRef":"its own top rail's 25 slots at the Picatinny pitch (std.picatinny.slot_pitch): each column read as a rail coordinate between the slot centres","method":"the front end of the rail's top edge (the last column whose silhouette top is within 4 px of the tooth tops, px 1743.5): 0.710 pitches ahead of the last slot's centre. BCM's photo of the black one reads 0.283 and Dirty Bird's 0.293 the same way (railfront.py)","via":"harvest"}}],"note":"A slot's half width and one land of about the standard's width, as on the 15 (0.283). The flare's tips are 0.10 in further forward by the photos, where the 15's are 0.32."},"mlok_side_slots":{"label":"M-LOK slots on each side face (3 and 9 o'clock)","kind":"count","measurements":[{"id":"photo","value":5,"unit":"count","source":{"type":"photo","photo":"references/bcm-mcmr-10-handguard 85d879b8ed8e (BCM's gallery for the Flat Dark Earth MCMR-10, MCMR_10_FDE: the handguard alone, its right side seen from about 18° above, 2000 x 1333)","scaleRef":"none: a count","method":"the slots of the lower row in the photo (the 3 o'clock face), 235.4 px apart, the whole row in frame from the mark at the rear to the flare: five (the foremost shows the far wall's inside through half its length, lit, where the far face's row has ended); five on the 9 o'clock face in BCM's photo of the black one (5336b2e8ad26) and in Dirty Bird's (cf89eca1f81a), and five on the level photo of the complete upper (dd70623d783b)","via":"harvest"}}]},"mlok_side_slot0_from_rail_slot0":{"label":"The side faces' rearmost M-LOK slot (its centre) ahead of the rail's rearmost slot's centre","kind":"length","measurements":[{"id":"photo","value":2.539,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bcm-mcmr-10-handguard 85d879b8ed8e (BCM's gallery for the Flat Dark Earth MCMR-10, MCMR_10_FDE: the handguard alone, its right side seen from about 18° above, 2000 x 1333)","scaleRef":"its own top rail's 25 slots at the Picatinny pitch (std.picatinny.slot_pitch): each column read as a rail coordinate between the slot centres; the row's own pitch gives k 1.0226","method":"the five slots' ten ends fitted to one pitch and one length (rms 0.008 in): the first slot's rear end at rail coordinate 4.687, true 4.845 pitches (1.9089 in), plus half the standard's slot (std.mlok.slot_length). BCM's photo of the black one reads 1.9212 and Dirty Bird's 1.9273 for the same end (ruler.py)","via":"harvest"}}],"note":"6.44 rail pitches: between two of the rail's slots. The three photos span 2.539 to 2.557."},"mlok_diag_slots":{"label":"M-LOK slots on each face between (1:30, 4:30, 7:30 and 10:30)","kind":"count","measurements":[{"id":"photo","value":5,"unit":"count","source":{"type":"photo","photo":"references/bcm-mcmr-10-handguard 85d879b8ed8e (BCM's gallery for the Flat Dark Earth MCMR-10, MCMR_10_FDE: the handguard alone, its right side seen from about 18° above, 2000 x 1333)","scaleRef":"none: a count","method":"the upper row of the photo (the 1:30 face), five slots 235 px apart, and five dark slots along the 4:30 face under the side row at the same columns; five on the 10:30 face in BCM's photo of the black one and in Dirty Bird's; five in the upper and five in the lower row of the level photo of the complete upper (dd70623d783b)","via":"harvest"}}]},"mlok_diag_slot0_from_rail_slot0":{"label":"The between faces' rearmost M-LOK slot (its centre) ahead of the rail's rearmost slot's centre","kind":"length","measurements":[{"id":"photo","value":2.148,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-mcmr-10-handguard 85d879b8ed8e (BCM's gallery for the Flat Dark Earth MCMR-10, MCMR_10_FDE: the handguard alone, its right side seen from about 18° above, 2000 x 1333)","scaleRef":"its own top rail's 25 slots at the Picatinny pitch (std.picatinny.slot_pitch): each column read as a rail coordinate between the slot centres; the row's own pitch gives k 1.0191","method":"the five slots' ten ends fitted to one pitch and one length (rms 0.003 in): the first slot's rear end at rail coordinate 3.701, true 3.853 pitches (1.5181 in), plus half the standard's slot. BCM's photo of the black one reads 1.5241 and Dirty Bird's 1.5249 for the same end","via":"harvest"}}],"note":"One rail pitch behind the side faces' row (0.391 here against 0.394). The three photos span 2.148 to 2.155."},"mlok_side_slot0_x":{"label":"The side faces' rearmost M-LOK slot (its centre) ahead of the receiver's front face","kind":"length","measurements":[{"id":"derived","value":2.724,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.rail_slot0_x} + {.mlok_side_slot0_from_rail_slot0}","via":"harvest"}}]},"mlok_diag_slot0_x":{"label":"The between faces' rearmost M-LOK slot (its centre) ahead of the receiver's front face","kind":"length","measurements":[{"id":"derived","value":2.333,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.rail_slot0_x} + {.mlok_diag_slot0_from_rail_slot0}","via":"harvest"}}]},"mlok_bottom_front_from_side_front":{"label":"The underside's foremost M-LOK slot (its centre) ahead of the side faces' foremost slot's","kind":"length","measurements":[{"id":"family","value":0.007,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{bcm-mcmr-15-handguard.mlok_bottom_front_from_side_front}","via":"harvest"}}],"note":"The family's, from the 15's ledger. On this length its foremost slot ends 0.058 in short of where the bottom flat ends (flare_bottom_run, 0.36 in behind the tips), where BCM's photo has an MCMR's within 0.015 in of it: inside what the two readings carry."},"mlok_bottom_slots":{"label":"M-LOK slots on the underside (6 o'clock)","kind":"count","measurements":[{"id":"assumed","value":5,"unit":"count","source":{"type":"derived","expr":"{.mlok_side_slots}","basis":"An assumption for the drawing, not a reading: the underside's row is read at its front end only, on an MCMR of a length the photo doesn't show (mlok_bottom_front_from_side_front); where it ends at the rear shows in no view on file or found, and the side faces' count is taken.","via":"harvest"}}]},"mlok_bottom_slot0_x":{"label":"The underside's rearmost M-LOK slot (its centre) ahead of the receiver's front face","kind":"length","measurements":[{"id":"derived","value":2.731,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.mlok_side_slot0_x} + ({.mlok_side_slots} - {.mlok_bottom_slots}) * {std.mlok.slot_pitch} + {.mlok_bottom_front_from_side_front}","via":"harvest"}}]},"reach_inside":{"label":"The room inside its faces, from a face in to the barrel (what an M-LOK accessory's nuts may take)","kind":"length","measurements":[],"note":"Not sourced: it depends on the barrel and gas block under it, other parts. Its wall is 0.1 in by BCM's two figures (1.5 wide, 1.3 inside)."},"rail_body_height":{"label":"The rail's depth, its top to where the neck's wall begins","kind":"length","measurements":[{"id":"family","value":0.215,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{bcm-mcmr-15-handguard.rail_body_height}","via":"harvest"}}]},"rail_bevel":{"label":"The slope under the rail's edges, its height as seen from the side","kind":"length","measurements":[{"id":"family","value":0.08,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{bcm-mcmr-15-handguard.rail_bevel}","via":"harvest"}}]},"neck_base_above_bore":{"label":"Where the upper faces end and the neck under the rail begins, above the bore","kind":"length","measurements":[{"id":"family","value":0.71,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{bcm-mcmr-15-handguard.neck_base_above_bore}","via":"harvest"}}]},"neck_width":{"label":"The neck's width under the rail","kind":"length","measurements":[{"id":"family","value":0.7013,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{bcm-mcmr-15-handguard.neck_width}","via":"harvest"}}]},"hole_center_above_bore":{"label":"The lightening holes under the rail, their centres above the bore","kind":"length","measurements":[{"id":"family","value":0.76,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{bcm-mcmr-15-handguard.hole_center_above_bore}","via":"harvest"}}]},"hole_pitch":{"label":"The lightening holes' pitch (oblong to oblong, round to round)","kind":"length","measurements":[{"id":"photo","value":0.787,"unit":"in","pm":0.003,"source":{"type":"photo","photo":"references/bcm-mcmr-10-handguard 85d879b8ed8e (BCM's gallery for the Flat Dark Earth MCMR-10, MCMR_10_FDE: the handguard alone, its right side seen from about 18° above, 2000 x 1333)","scaleRef":"its own top rail's 25 slots at the Picatinny pitch (std.picatinny.slot_pitch): each column read as a rail coordinate between the slot centres; k 1.018 for the neck's near wall","method":"ten oblong holes' dark lower halves from px 561.5 to 1616.2, 117.2 px apart: 1.9985 pitches; five round holes two apart from px 508.0 to 1443.7: 1.995 (.cache/batch46/bcm-mcmr-10-handguard/bolts.py)","via":"harvest"}}],"note":"Two rail pitches."},"hole_count":{"label":"Lightening holes of each kind on each side","kind":"count","measurements":[{"id":"photo","value":11,"unit":"count","source":{"type":"photo","photo":"references/bcm-mcmr-10-handguard 85d879b8ed8e (BCM's gallery for the Flat Dark Earth MCMR-10, MCMR_10_FDE: the handguard alone, its right side seen from about 18° above, 2000 x 1333)","scaleRef":"none: a count","method":"eleven oblong holes from px 450 to 1622, 117.2 px apart, a round one ahead of each (px 508 to 1679, the rail's front end 0.44 in ahead of the last); counted on the whole row, from the cross-bolt holes to the flare","via":"harvest"}}]},"hole_oblong0_from_rail_slot0":{"label":"The rearmost oblong hole (its centre) ahead of the rail's rearmost slot's centre","kind":"length","measurements":[{"id":"photo","value":0.96,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-mcmr-10-handguard 85d879b8ed8e (BCM's gallery for the Flat Dark Earth MCMR-10, MCMR_10_FDE: the handguard alone, its right side seen from about 18° above, 2000 x 1333)","scaleRef":"its own top rail's 25 slots at the Picatinny pitch (std.picatinny.slot_pitch): each column read as a rail coordinate between the slot centres; k 1.018 for the neck's near wall","method":"the hole's dark outline's centroid at px 450.3 (it is dark all through: the far wall's hole isn't behind it): rail coordinate 2.265, true 2.436 pitches; the round hole ahead of it at px 508.0, 0.985 pitches on (bolts.py)","via":"harvest"}}],"note":"2.44 rail pitches, where the 15's is 3.92: this length's row of holes begins a pitch and a half further back."},"hole_oblong_length":{"label":"An oblong hole's length","kind":"length","measurements":[{"id":"family","value":0.39,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{bcm-mcmr-15-handguard.hole_oblong_length}","via":"harvest"}}]},"hole_oblong_width":{"label":"An oblong hole's width","kind":"length","measurements":[{"id":"family","value":0.2,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{bcm-mcmr-15-handguard.hole_oblong_width}","via":"harvest"}}]},"hole_oblong_slant":{"label":"An oblong hole's slant from the rail's line (its top toward the muzzle)","kind":"angle","measurements":[{"id":"family","value":58,"unit":"deg","pm":5,"source":{"type":"derived","expr":"{bcm-mcmr-15-handguard.hole_oblong_slant}","via":"harvest"}}]},"hole_round_d":{"label":"A round lightening hole's diameter","kind":"length","measurements":[{"id":"family","value":0.19,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{bcm-mcmr-15-handguard.hole_round_d}","via":"harvest"}}]},"cross_bolt0_from_rail_slot0":{"label":"The rear cross-bolt hole (its centre) ahead of the rail's rearmost slot's centre","kind":"length","measurements":[{"id":"photo","value":0.144,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-mcmr-10-handguard 85d879b8ed8e (BCM's gallery for the Flat Dark Earth MCMR-10, MCMR_10_FDE: the handguard alone, its right side seen from about 18° above, 2000 x 1333)","scaleRef":"its own top rail's 25 slots at the Picatinny pitch (std.picatinny.slot_pitch): each column read as a rail coordinate between the slot centres; k 1.019","method":"the hole's dark outline's centroid at px 328.6: true rail coordinate 0.366 pitches (bolts.py)","via":"harvest"}}]},"cross_bolt_spacing":{"label":"The two cross-bolt holes, centre to centre","kind":"length","measurements":[{"id":"photo","value":0.219,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-mcmr-10-handguard 85d879b8ed8e (BCM's gallery for the Flat Dark Earth MCMR-10, MCMR_10_FDE: the handguard alone, its right side seen from about 18° above, 2000 x 1333)","scaleRef":"its own top rail's 25 slots at the Picatinny pitch (std.picatinny.slot_pitch): each column read as a rail coordinate between the slot centres","method":"the two outlines' centroids at px 328.6 and 361.2: 0.555 pitches apart; each outline 0.17 by 0.20 in","via":"harvest"}}]},"cross_bolt_d":{"label":"A cross-bolt hole's diameter, as it shows","kind":"length","measurements":[{"id":"family","value":0.18,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{bcm-mcmr-15-handguard.cross_bolt_d}","via":"harvest"}}]},"cross_bolt_above_bore":{"label":"The cross-bolt holes' centres above the bore","kind":"length","measurements":[{"id":"family","value":0.6,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{bcm-mcmr-15-handguard.cross_bolt_above_bore}","via":"harvest"}}]},"flare_tip_top":{"label":"The flat tips of the side faces, their upper corner above the bore","kind":"length","measurements":[{"id":"photo","value":0.31,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mcmr-10-handguard 85d879b8ed8e (BCM's gallery for the Flat Dark Earth MCMR-10, MCMR_10_FDE: the handguard alone, its right side seen from about 18° above, 2000 x 1333)","scaleRef":"its own rail's pitch (146.2 px/in), the side face 1.0226 nearer; the rail's far top edge at row 510.5 and the side row's centre line at row 732.5 for the angle (18.5°)","method":"the front boundary of the handguard's own colour, row by row: it stands at px 1778 from row 689 to row 772; the upper corner (1778, 689) on the side face is 0.307 above the bore","via":"harvest"}}],"note":"The side face's own upper edge is 0.311 above the bore (a regular octagon 1.5 across). BCM's photo of the black one reads 0.27 and Dirty Bird's 0.31."},"flare_tip_bottom":{"label":"The flat tips of the side faces, their lower corner above the bore (negative: below it)","kind":"length","measurements":[{"id":"photo","value":-0.28,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-mcmr-10-handguard 85d879b8ed8e (BCM's gallery for the Flat Dark Earth MCMR-10, MCMR_10_FDE: the handguard alone, its right side seen from about 18° above, 2000 x 1333)","scaleRef":"its own rail's pitch (146.2 px/in), the side face 1.0226 nearer; the angle as for the upper corner","method":"the lower corner (1773, 772), where the front boundary turns back toward the bottom: 0.281 below the bore on the side face","via":"harvest"}}],"note":"The side face's own lower edge is 0.311 below the bore. BCM's photo of the black one reads -0.35 and Dirty Bird's -0.34, each from corners picked to 3 px at half this photo's scale."},"flare_face_bottom":{"label":"Where the square front face under the rail's end gives way to the slope down to the tips, above the bore","kind":"length","measurements":[{"id":"photo","value":0.63,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/bcm-mcmr-10-handguard 85d879b8ed8e (BCM's gallery for the Flat Dark Earth MCMR-10, MCMR_10_FDE: the handguard alone, its right side seen from about 18° above, 2000 x 1333)","scaleRef":"its own rail's pitch (146.2 px/in); the angle as for the tips","method":"the front boundary stands at px 1755 to 1756 from the rail's side down to row 628, then runs out to the tip: the corner (1755, 628), taken on the upper face between (which a regular octagon puts at 45°), is 0.631 above the bore and 0.02 in behind the rail's front end, one plane with it","via":"harvest"}}],"note":"On the upper face between, under the neck (neck_base_above_bore, 0.71): the 15's front face ends higher, in its neck. BCM's photo of the black one reads 0.52 and Dirty Bird's 0.56; on BCM's level photos of the complete upper the boundary turns between 0.52 and 0.69. The same reading on the 15's photo is 0.05 over its level outline, so this may be as much high."},"flare_bottom_run":{"label":"How far behind the tips the bottom flat ends","kind":"length","measurements":[{"id":"photo","value":0.36,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/bcm-mcmr-10-handguard 85d879b8ed8e (BCM's gallery for the Flat Dark Earth MCMR-10, MCMR_10_FDE: the handguard alone, its right side seen from about 18° above, 2000 x 1333)","scaleRef":"its own rail's pitch (146.2 px/in); the tips at the side face's scale, the bottom flat's near edge at the rail's own (it stands as far from the lens as the rail's far edge does, seen from there)","method":"the front boundary below the tips runs back 7.5 px in 5 rows to the bottom flat's near edge (row 813 to 815) at px 1708 to 1710: 0.355 in behind the tips' true place","via":"harvest"}}],"note":"BCM's photo of the black one reads 0.29 and Dirty Bird's 0.32. The same reading on the 15's photo is 0.05 under its level outline (0.36 against 0.41)."}}},{"subject":"bcm-mcmr-13-handguard","title":"BCM MCMR-13 M-LOK Compatible Modular Rail (BCM-MCMR-13-556-BLK)","dimensions":{"weight":{"label":"Weight on the rifle (the handguard and its mounting hardware)","kind":"mass","measurements":[{"id":"sum","value":10.5,"unit":"oz","pm":0.1,"source":{"type":"derived","expr":"{.weight_handguard} + {.weight_hardware}","via":"harvest"}},{"id":"trex-arms","value":10.5,"unit":"oz","pm":0.05,"stated":"MCMR-9 MCMR-13 Weight w/ Barrel Nut 8.2 oz 10.5 oz","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, BCM 5.56 Handguard, the table BCM MCMR HANDGUARD (its second column is the MCMR-13)","url":"https://trex-arms.com/store/bcm-5-56-handguard","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":10.5,"unit":"oz","pm":0.05,"stated":"Weight 10.5 oz.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Bravo Company Manufacturing MCMR Free Float AR-15 Handguard - M-LOK - 13\" - FDE (BCM-MCMR-13-556-FDE), specifications","url":"https://www.primaryarms.com/bravo-company-manufacturing-mcmr-13-modular-rail-ar-15-handguard-13-4in-fde","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"sum","reason":"The maker's two figures; the two sellers' one figure is their sum."},"note":"BCM gives the two apart; what goes on the rifle is both. Whether the steel barrel nut is in the 2.3 oz of hardware BCM doesn't say in so many words: T.REX ARMS' table for this length calls their sum \"Weight w/ Barrel Nut\", and Primary Arms' one figure for the Flat Dark Earth one is the same sum."},"weight_handguard":{"label":"Weight, the handguard alone","kind":"mass","measurements":[{"id":"bcm","value":8.2,"unit":"oz","pm":0.05,"stated":"Handguard alone weighs 8.2 oz","source":{"type":"spec","publisher":"manufacturer","name":"Bravo Company USA, BCM® MCMR-13 (M-LOK® Compatible* Modular Rail) (BCM-MCMR-13-556-BLK), Description","url":"https://bravocompanyusa.com/bcm-mcmr-13-m-lok-compatible-modular-rail/","retrieved":"2026-10-06","via":"harvest"}}]},"weight_hardware":{"label":"Weight, its mounting hardware","kind":"mass","measurements":[{"id":"bcm","value":2.3,"unit":"oz","pm":0.05,"stated":"Handguard mounting hardware 2.3 oz","source":{"type":"spec","publisher":"manufacturer","name":"Bravo Company USA, BCM® MCMR-13 (M-LOK® Compatible* Modular Rail) (BCM-MCMR-13-556-BLK), Description","url":"https://bravocompanyusa.com/bcm-mcmr-13-m-lok-compatible-modular-rail/","retrieved":"2026-10-06","via":"harvest"}}],"note":"The same 2.3 oz on every length's page: the manual's bill of materials (the barrel nut, two clamp blocks, the index plate and the two cross bolts) is the series'."},"length":{"label":"Length, end to end (the rear end to the tips of the flare)","kind":"length","measurements":[{"id":"bcm","value":13.4,"unit":"in","pm":0.05,"stated":"Actual length when measured to flare is 13.4\"","source":{"type":"spec","publisher":"manufacturer","name":"Bravo Company USA, BCM® MCMR-13 (M-LOK® Compatible* Modular Rail) (BCM-MCMR-13-556-BLK), Description","url":"https://bravocompanyusa.com/bcm-mcmr-13-m-lok-compatible-modular-rail/","retrieved":"2026-10-06","via":"harvest"}},{"id":"photo","value":13.42,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-mcmr-13-handguard 4d10da7d6e2b (BCM's gallery for the Flat Dark Earth MCMR-13, MCMR_13_FDE: the handguard alone, its right side seen from about 18° above, 2000 x 1334)","scaleRef":"its own top rail's 32 slots at the Picatinny pitch (std.picatinny.slot_pitch): each column read as a rail coordinate between the slot centres; the side faces' M-LOK row (pitch 186.4 px for 40 mm) for what stands at their depth, k 1.0205","method":"the silhouette's two ends (px 207 and 1796) as rail coordinates -1.960 and 32.813, each brought to its true place about the image's centre: -1.610 and 32.462 pitches. BCM's photo of the black one a11c8b3fadd7 reads 13.45 and Dirty Bird's 2f54ba5dc3f4 13.45 the same way (.cache/batch46/bcm-mcmr-10-handguard/ruler.py)","via":"harvest"}}],"adopt":{"from":"bcm","reason":"The maker's figure; three photos read 0.02 to 0.05 more, inside what its one decimal and their ± allow."},"note":"BCM's \"13\" is 13.4 in \"to flare\", which is the whole length: the side faces run forward into two flat tips (the flare), 0.58 in past the rail's last slot's centre. Primary Arms says what the \"13\" is: \"the listed 13-inch length refers to the top Picatinny rail section; the overall handguard measures slightly longer at 13.4 inches total\" (its page for the Flat Dark Earth one; rail_length). T.REX ARMS' table has \"Actual Length\" 13.4 in. The photos read 13.42 to 13.45 at the scale of the side faces, where both ends are."},"rail_length":{"label":"Its top rail's length, end to end","kind":"length","measurements":[{"id":"photos","value":13.123,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.rail_slot0_from_rear} + ({.rail_slots} - 1) * {std.picatinny.slot_pitch} + {.rail_front_from_last_slot}","via":"harvest"}}],"note":"What the \"13\" in its name is, by the one seller that says so (Primary Arms, of the Flat Dark Earth one: \"the listed 13-inch length refers to the top Picatinny rail section\"; it gives no figure for the rail). The photos have its rail 0.630 in behind its first slot's centre, 31 pitches, and 0.28 in ahead of its last: 13.12."},"width":{"label":"Width across the flats (3 to 9 o'clock)","kind":"length","measurements":[{"id":"bcm","value":1.5,"unit":"in","pm":0.05,"stated":"1.5\" Wide","source":{"type":"spec","publisher":"manufacturer","name":"Bravo Company USA, BCM® MCMR-13 (M-LOK® Compatible* Modular Rail) (BCM-MCMR-13-556-BLK), Description","url":"https://bravocompanyusa.com/bcm-mcmr-13-m-lok-compatible-modular-rail/","retrieved":"2026-10-06","via":"harvest"}}]},"height":{"label":"Height (the rail's top to the bottom flat)","kind":"length","measurements":[{"id":"family","value":1.944,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{bcm-mcmr-15-handguard.height}","via":"harvest"}}],"note":"Not published. The family's section: the 15's figure, read on the one level photo of an MCMR alone. On this length's own photo from 18.6° above, the silhouette of its own colour is 2.08 in high at the rail's scale (rows 538 to 778), where that section (the rail's top 1.20 above the bore, a regular octagon 1.5 across) seen from there is 2.08."},"inside_diameter":{"label":"Inside diameter","kind":"length","measurements":[{"id":"bcm","value":1.3,"unit":"in","pm":0.05,"stated":"1.3\" Inside Diameter","source":{"type":"spec","publisher":"manufacturer","name":"Bravo Company USA, BCM® MCMR-13 (M-LOK® Compatible* Modular Rail) (BCM-MCMR-13-556-BLK), Description","url":"https://bravocompanyusa.com/bcm-mcmr-13-m-lok-compatible-modular-rail/","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":1.3,"unit":"in","pm":0.005,"stated":"Inner Diameter 1.30 in.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Bravo Company Manufacturing MCMR Free Float AR-15 Handguard - M-LOK - 13\" - FDE (BCM-MCMR-13-556-FDE), specifications","url":"https://www.primaryarms.com/bravo-company-manufacturing-mcmr-13-modular-rail-ar-15-handguard-13-4in-fde","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"bcm","reason":"The maker's; the seller repeats it."},"note":"The round bore at its rear end, which goes over the barrel nut. Ahead of it the inside follows the outside (BCM's three-quarter views of this length from behind, 43945a2790cd and 09be27135ec4, show flat inner walls past the round part): the model takes 1.3 in across the inner flats."},"receiver_gap":{"label":"The gap left between its rear end and the upper receiver","kind":"length","measurements":[{"id":"family","value":0.0225,"unit":"in","pm":0.0175,"source":{"type":"derived","expr":"{bcm-mcmr-15-handguard.receiver_gap}","via":"harvest"}}],"note":"The series' installation manual (KMR-A, MCMR, QRF; the same file is linked from BCM's rail page, harvested for this length): the 15's entry quotes its step 14, a gap of .005 to .040 in."},"rear_x":{"label":"Its rear end against the receiver's front face (negative: behind it)","kind":"length","measurements":[{"id":"derived","value":-0.4225,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"0in - {std.ar15.upper_barrel_thread_length} + {.receiver_gap}","via":"harvest"}},{"id":"installed","value":-0.444,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mcmr-13-handguard ce21a844019e (BCM's gallery for the complete upper BCM-URG-MID-14-MCMR-13, -2: its right side seen level, 1500 x 1000) and 1e811e94017f (-3: its left side, 1500 x 1000)","scaleRef":"the receiver's two lug holes, std.ar15.pin_spacing apart: 54.20 and 57.59 px/in","method":"the handguard's rearmost rail slot's centre 7.219 and 7.225 in ahead of the takedown hole (0.186 ahead of the receiver's front face, std.ar15.upper_front_face_x, between the two), less this ledger's rail_slot0_from_rear (0.630, BCM's photo of the handguard alone) (.cache/batch46/bcm-mcmr-10-handguard/urg.py)","via":"harvest"},"note":"A check through two photos, each with its own ±."}],"adopt":{"from":"derived","reason":"BCM's own rule for where it stops; the photos of the complete upper put it 0.02 in behind that, within their ±."},"note":"It slides back over its barrel nut to the receiver's front shoulder, where the barrel-nut thread begins (std.ar15.upper_barrel_thread_length behind the front face), less the gap BCM's manual asks for."},"barrel_max_od":{"label":"The largest barrel its barrel nut goes over","kind":"length","measurements":[{"id":"bcm","value":1,"unit":"in","pm":0.05,"stated":"The barrel nut will fit over all mil-spec diameter barrels (max of 1\")","source":{"type":"spec","publisher":"manufacturer","name":"Bravo Company USA, BCM® MCMR-13 (M-LOK® Compatible* Modular Rail) (BCM-MCMR-13-556-BLK), Description","url":"https://bravocompanyusa.com/bcm-mcmr-13-m-lok-compatible-modular-rail/","retrieved":"2026-10-06","via":"harvest"}}]},"rail_top_above_bore":{"label":"Its rail's top above the bore axis","kind":"length","measurements":[{"id":"family","value":1.2,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{bcm-mcmr-15-handguard.rail_top_above_bore}","via":"harvest"}}],"note":"The family's: the 15's figure (its tube is about the bore, its rail level with a mil-spec receiver's). On BCM's two photos of the 14.5 in upper with this length on it, its rail's tooth tops read 0.02 in under the receiver's on the right side (2.038 against 2.056 above the pin line, in a photo whose scale runs 2.8% short along the handguard) and 0.01 under it on the left (2.086 against 2.094)."},"rail_slots":{"label":"Slots in its top rail","kind":"count","measurements":[{"id":"photo","value":32,"unit":"count","source":{"type":"photo","photo":"references/bcm-mcmr-13-handguard 4d10da7d6e2b (BCM's gallery for the Flat Dark Earth MCMR-13, MCMR_13_FDE: the handguard alone, its right side seen from about 18° above, 2000 x 1334)","scaleRef":"none: a count","method":"the notches between the teeth along the top edge, each 45.7 px from the next (sd 0.09), at five depths under the tooth tops: 32; the same count on BCM's photo of the black one (a11c8b3fadd7, 35.8 px apart) and Dirty Bird's (2f54ba5dc3f4, 30.6 px), and on BCM's two photos of the complete upper (ce21a844019e, 1e811e94017f)","via":"harvest"}}]},"rail_slot0_from_rear":{"label":"Its rail's rearmost slot (its centre) ahead of its rear end","kind":"length","measurements":[{"id":"bcm-photo","value":0.63,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-mcmr-13-handguard 4d10da7d6e2b (BCM's gallery for the Flat Dark Earth MCMR-13, MCMR_13_FDE: the handguard alone, its right side seen from about 18° above, 2000 x 1334)","scaleRef":"its own top rail's 32 slots at the Picatinny pitch (std.picatinny.slot_pitch): each column read as a rail coordinate between the slot centres","method":"the rear end of the rail's top edge (the first column whose silhouette top is within 4 px of the tooth tops, px 223.5): 1.598 pitches behind the first slot's centre (.cache/batch46/bcm-mcmr-10-handguard/railfront.py)","via":"harvest"}},{"id":"bcm-black-photo","value":0.624,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-mcmr-13-handguard a11c8b3fadd7 (BCM's gallery, BCM-MCMR-13-556-BLK-2: the black handguard alone above its hardware, its left side seen from about 20° above, 1500 x 1000)","scaleRef":"its own top rail's 32 slots at the Picatinny pitch (std.picatinny.slot_pitch): each column read as a rail coordinate between the slot centres","method":"the same edge (mirrored px 148.5): 1.584 pitches behind the first slot's centre, at 91 px/in","via":"harvest"}},{"id":"dirty-bird-photo","value":0.626,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-mcmr-13-handguard 2f54ba5dc3f4 (Dirty Bird's gallery, the 13 in black: its left side from about 18° above, 1113 x 865)","scaleRef":"its own top rail's 32 slots at the Picatinny pitch (std.picatinny.slot_pitch): each column read as a rail coordinate between the slot centres","method":"the same edge (mirrored px 32.5): 1.588 pitches behind the first slot's centre, at 78 px/in","via":"harvest"}}],"adopt":{"from":"bcm-photo","reason":"The maker's own photograph at the largest scale; the other two read 0.006 and 0.004 less."},"note":"Read to the rail's own rear end, along the far edge of its top, which is where the slots are read: nothing to bring to another depth. The body's rear end (the side face's, brought to its depth) reads 0.634 behind the slot in the same photo. The 15's is 0.623 and the 10's 0.607: one clamp end, read to 0.02."},"rail_slot0_x":{"label":"Its rail's rearmost slot (its centre) ahead of the receiver's front face","kind":"length","measurements":[{"id":"installed","value":0.186,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-mcmr-13-handguard ce21a844019e (BCM's gallery for the complete upper BCM-URG-MID-14-MCMR-13, -2: its right side seen level, 1500 x 1000) and 1e811e94017f (-3: its left side, 1500 x 1000)","scaleRef":"the receiver's two lug holes, std.ar15.pin_spacing apart: 54.20 and 57.59 px/in; the receiver's own 13 rail slots read 0.393 and 0.391 a pitch on them","method":"the gaps between the teeth 0.04 to 0.08 in below the tooth tops, each edge at the 50% level: the handguard's first slot's centre 7.219 in ahead of the takedown hole on the right photo and 7.225 on the left, less the receiver's front face (std.ar15.upper_front_face_x, 7.036): 0.183 and 0.189. It is 1.169 and 1.178 in ahead of the receiver's last slot: three pitches (.cache/batch46/bcm-mcmr-10-handguard/urg.py)","via":"harvest"}},{"id":"through-rear","value":0.2075,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.rear_x} + {.rail_slot0_from_rear}","via":"harvest"}}],"adopt":{"from":"installed","reason":"Read where it matters, in the receiver's own frame on two photos; the other goes through the handguard's rear end, which the gap at the receiver moves, and lands 0.02 in ahead of it."}},"rail_front_from_last_slot":{"label":"Its rail's front end ahead of its last slot's centre","kind":"length","measurements":[{"id":"photo","value":0.279,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bcm-mcmr-13-handguard 4d10da7d6e2b (BCM's gallery for the Flat Dark Earth MCMR-13, MCMR_13_FDE: the handguard alone, its right side seen from about 18° above, 2000 x 1334)","scaleRef":"its own top rail's 32 slots at the Picatinny pitch (std.picatinny.slot_pitch): each column read as a rail coordinate between the slot centres","method":"the front end of the rail's top edge (the last column whose silhouette top is within 4 px of the tooth tops, px 1745.5): 0.708 pitches ahead of the last slot's centre. BCM's photo of the black one reads 0.293 and Dirty Bird's 0.291 the same way (railfront.py)","via":"harvest"}}],"note":"A slot's half width and one land of about the standard's width, as on the 15 (0.283). The flare's tips are 0.27 in further forward by the photos, where the 15's are 0.32 and the 10's 0.10."},"mlok_side_slots":{"label":"M-LOK slots on each side face (3 and 9 o'clock)","kind":"count","measurements":[{"id":"photo","value":7,"unit":"count","source":{"type":"photo","photo":"references/bcm-mcmr-13-handguard 4d10da7d6e2b (BCM's gallery for the Flat Dark Earth MCMR-13, MCMR_13_FDE: the handguard alone, its right side seen from about 18° above, 2000 x 1334)","scaleRef":"none: a count","method":"the slots of the lower row in the photo (the 3 o'clock face), 186.4 px apart, the whole row in frame from the mark at the rear to the flare: seven (the foremost shows the far wall's inside through half its length, lit, where the far face's row has ended); seven on the 9 o'clock face in BCM's photo of the black one (a11c8b3fadd7) and in Dirty Bird's (2f54ba5dc3f4), and seven on the level photo of the complete upper (ce21a844019e)","via":"harvest"}}]},"mlok_side_slot0_from_rail_slot0":{"label":"The side faces' rearmost M-LOK slot (its centre) ahead of the rail's rearmost slot's centre","kind":"length","measurements":[{"id":"photo","value":2.316,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bcm-mcmr-13-handguard 4d10da7d6e2b (BCM's gallery for the Flat Dark Earth MCMR-13, MCMR_13_FDE: the handguard alone, its right side seen from about 18° above, 2000 x 1334)","scaleRef":"its own top rail's 32 slots at the Picatinny pitch (std.picatinny.slot_pitch): each column read as a rail coordinate between the slot centres; the row's own pitch gives k 1.0205","method":"the seven slots' fourteen ends, one left out (the foremost slot's front end, where the far wall shows through), fitted to one pitch and one length (rms 0.003 in): the first slot's rear end at rail coordinate 4.051, true 4.280 pitches (1.6861 in), plus half the standard's slot (std.mlok.slot_length). BCM's photo of the black one reads 1.6917 and Dirty Bird's 1.6884 for the same end (ruler.py)","via":"harvest"}}],"note":"5.88 rail pitches. The three photos span 2.316 to 2.322."},"mlok_diag_slots":{"label":"M-LOK slots on each face between (1:30, 4:30, 7:30 and 10:30)","kind":"count","measurements":[{"id":"photo","value":7,"unit":"count","source":{"type":"photo","photo":"references/bcm-mcmr-13-handguard 4d10da7d6e2b (BCM's gallery for the Flat Dark Earth MCMR-13, MCMR_13_FDE: the handguard alone, its right side seen from about 18° above, 2000 x 1334)","scaleRef":"none: a count","method":"the upper row of the photo (the 1:30 face), seven slots 186 px apart, and seven dark slots along the 4:30 face under the side row at the same columns; seven on the 10:30 face in BCM's photo of the black one and in Dirty Bird's; seven in the upper and seven in the lower row of the level photo of the complete upper (ce21a844019e)","via":"harvest"}}]},"mlok_diag_slot0_from_rail_slot0":{"label":"The between faces' rearmost M-LOK slot (its centre) ahead of the rail's rearmost slot's centre","kind":"length","measurements":[{"id":"photo","value":1.915,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bcm-mcmr-13-handguard 4d10da7d6e2b (BCM's gallery for the Flat Dark Earth MCMR-13, MCMR_13_FDE: the handguard alone, its right side seen from about 18° above, 2000 x 1334)","scaleRef":"its own top rail's 32 slots at the Picatinny pitch (std.picatinny.slot_pitch): each column read as a rail coordinate between the slot centres; the row's own pitch gives k 1.0201","method":"the seven slots' fourteen ends fitted to one pitch and one length (rms 0.002 in): the first slot's rear end at rail coordinate 3.018, true 3.262 pitches (1.2853 in), plus half the standard's slot. BCM's photo of the black one reads 1.2960 and Dirty Bird's 1.2979 for the same end","via":"harvest"}}],"note":"One rail pitch behind the side faces' row (0.401 here against 0.394). The three photos span 1.915 to 1.928."},"mlok_side_slot0_x":{"label":"The side faces' rearmost M-LOK slot (its centre) ahead of the receiver's front face","kind":"length","measurements":[{"id":"derived","value":2.502,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.rail_slot0_x} + {.mlok_side_slot0_from_rail_slot0}","via":"harvest"}}]},"mlok_diag_slot0_x":{"label":"The between faces' rearmost M-LOK slot (its centre) ahead of the receiver's front face","kind":"length","measurements":[{"id":"derived","value":2.101,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.rail_slot0_x} + {.mlok_diag_slot0_from_rail_slot0}","via":"harvest"}}]},"mlok_bottom_front_from_side_front":{"label":"The underside's foremost M-LOK slot (its centre) ahead of the side faces' foremost slot's","kind":"length","measurements":[{"id":"family","value":0.007,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{bcm-mcmr-15-handguard.mlok_bottom_front_from_side_front}","via":"harvest"}}],"note":"The family's, from the 15's ledger. On this length its foremost slot ends 0.040 in short of where the bottom flat ends (flare_bottom_run, 0.35 in behind the tips), where BCM's photo has an MCMR's within 0.015 in of it: inside what the two readings carry."},"mlok_bottom_slots":{"label":"M-LOK slots on the underside (6 o'clock)","kind":"count","measurements":[{"id":"assumed","value":7,"unit":"count","source":{"type":"derived","expr":"{.mlok_side_slots}","basis":"An assumption for the drawing, not a reading: the underside's row is read at its front end only, on an MCMR of a length the photo doesn't show (mlok_bottom_front_from_side_front); where it ends at the rear shows in no view on file or found, and the side faces' count is taken.","via":"harvest"}}]},"mlok_bottom_slot0_x":{"label":"The underside's rearmost M-LOK slot (its centre) ahead of the receiver's front face","kind":"length","measurements":[{"id":"derived","value":2.509,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.mlok_side_slot0_x} + ({.mlok_side_slots} - {.mlok_bottom_slots}) * {std.mlok.slot_pitch} + {.mlok_bottom_front_from_side_front}","via":"harvest"}}]},"reach_inside":{"label":"The room inside its faces, from a face in to the barrel (what an M-LOK accessory's nuts may take)","kind":"length","measurements":[],"note":"Not sourced: it depends on the barrel and gas block under it, other parts. Its wall is 0.1 in by BCM's two figures (1.5 wide, 1.3 inside)."},"rail_body_height":{"label":"The rail's depth, its top to where the neck's wall begins","kind":"length","measurements":[{"id":"family","value":0.215,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{bcm-mcmr-15-handguard.rail_body_height}","via":"harvest"}}]},"rail_bevel":{"label":"The slope under the rail's edges, its height as seen from the side","kind":"length","measurements":[{"id":"family","value":0.08,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{bcm-mcmr-15-handguard.rail_bevel}","via":"harvest"}}]},"neck_base_above_bore":{"label":"Where the upper faces end and the neck under the rail begins, above the bore","kind":"length","measurements":[{"id":"family","value":0.71,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{bcm-mcmr-15-handguard.neck_base_above_bore}","via":"harvest"}}]},"neck_width":{"label":"The neck's width under the rail","kind":"length","measurements":[{"id":"family","value":0.7013,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{bcm-mcmr-15-handguard.neck_width}","via":"harvest"}}]},"hole_center_above_bore":{"label":"The lightening holes under the rail, their centres above the bore","kind":"length","measurements":[{"id":"family","value":0.76,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{bcm-mcmr-15-handguard.hole_center_above_bore}","via":"harvest"}}]},"hole_pitch":{"label":"The lightening holes' pitch (oblong to oblong, round to round)","kind":"length","measurements":[{"id":"photo","value":0.786,"unit":"in","pm":0.003,"source":{"type":"photo","photo":"references/bcm-mcmr-13-handguard 4d10da7d6e2b (BCM's gallery for the Flat Dark Earth MCMR-13, MCMR_13_FDE: the handguard alone, its right side seen from about 18° above, 2000 x 1334)","scaleRef":"its own top rail's 32 slots at the Picatinny pitch (std.picatinny.slot_pitch): each column read as a rail coordinate between the slot centres; k 1.018 for the neck's near wall","method":"thirteen oblong holes' dark lower halves from px 456.8 to 1572.4, 92.97 px apart: 1.998 pitches; seven round holes two apart from px 415.3 to 1528.0: 1.993 (.cache/batch46/bcm-mcmr-10-handguard/bolts.py)","via":"harvest"}}],"note":"Two rail pitches."},"hole_count":{"label":"Lightening holes of each kind on each side","kind":"count","measurements":[{"id":"photo","value":15,"unit":"count","source":{"type":"photo","photo":"references/bcm-mcmr-13-handguard 4d10da7d6e2b (BCM's gallery for the Flat Dark Earth MCMR-13, MCMR_13_FDE: the handguard alone, its right side seen from about 18° above, 2000 x 1334)","scaleRef":"none: a count","method":"fifteen oblong holes from px 369.5 to 1671, 92.9 px apart, a round one ahead of each (px 415 to 1714, the last at the rail's very end: 0.27 in behind its front as it shows, 0.37 in once it is brought to the neck's near wall, where the model has it); counted on the whole row, from the cross-bolt holes to the flare, on the photo and on its two halves enlarged","via":"harvest"}}]},"hole_oblong0_from_rail_slot0":{"label":"The rearmost oblong hole (its centre) ahead of the rail's rearmost slot's centre","kind":"length","measurements":[{"id":"photo","value":0.728,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-mcmr-13-handguard 4d10da7d6e2b (BCM's gallery for the Flat Dark Earth MCMR-13, MCMR_13_FDE: the handguard alone, its right side seen from about 18° above, 2000 x 1334)","scaleRef":"its own top rail's 32 slots at the Picatinny pitch (std.picatinny.slot_pitch): each column read as a rail coordinate between the slot centres; k 1.018 for the neck's near wall","method":"the hole's dark outline's centroid at px 369.5 (it is dark all through: the far wall's hole isn't behind it): rail coordinate 1.600, true 1.847 pitches; the round hole ahead of it at px 415.3, 0.986 pitches on (bolts.py)","via":"harvest"}}],"note":"1.85 rail pitches, where the 15's is 3.92 and the 10's 2.44: this length's row of holes begins two pitches further back than the 15's."},"hole_oblong_length":{"label":"An oblong hole's length","kind":"length","measurements":[{"id":"family","value":0.39,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{bcm-mcmr-15-handguard.hole_oblong_length}","via":"harvest"}}]},"hole_oblong_width":{"label":"An oblong hole's width","kind":"length","measurements":[{"id":"family","value":0.2,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{bcm-mcmr-15-handguard.hole_oblong_width}","via":"harvest"}}]},"hole_oblong_slant":{"label":"An oblong hole's slant from the rail's line (its top toward the muzzle)","kind":"angle","measurements":[{"id":"family","value":58,"unit":"deg","pm":5,"source":{"type":"derived","expr":"{bcm-mcmr-15-handguard.hole_oblong_slant}","via":"harvest"}}]},"hole_round_d":{"label":"A round lightening hole's diameter","kind":"length","measurements":[{"id":"family","value":0.19,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{bcm-mcmr-15-handguard.hole_round_d}","via":"harvest"}}]},"cross_bolt0_from_rail_slot0":{"label":"The rear cross-bolt hole (its centre) ahead of the rail's rearmost slot's centre","kind":"length","measurements":[{"id":"photo","value":0.15,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-mcmr-13-handguard 4d10da7d6e2b (BCM's gallery for the Flat Dark Earth MCMR-13, MCMR_13_FDE: the handguard alone, its right side seen from about 18° above, 2000 x 1334)","scaleRef":"its own top rail's 32 slots at the Picatinny pitch (std.picatinny.slot_pitch): each column read as a rail coordinate between the slot centres; k 1.019","method":"the hole's dark outline's centroid at px 300.7: true rail coordinate 0.380 pitches (bolts.py)","via":"harvest"}}]},"cross_bolt_spacing":{"label":"The two cross-bolt holes, centre to centre","kind":"length","measurements":[{"id":"photo","value":0.219,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-mcmr-13-handguard 4d10da7d6e2b (BCM's gallery for the Flat Dark Earth MCMR-13, MCMR_13_FDE: the handguard alone, its right side seen from about 18° above, 2000 x 1334)","scaleRef":"its own top rail's 32 slots at the Picatinny pitch (std.picatinny.slot_pitch): each column read as a rail coordinate between the slot centres","method":"the two outlines' centroids at px 300.7 and 326.5: 0.555 pitches apart; each outline 0.17 by 0.19 in","via":"harvest"}}]},"cross_bolt_d":{"label":"A cross-bolt hole's diameter, as it shows","kind":"length","measurements":[{"id":"family","value":0.18,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{bcm-mcmr-15-handguard.cross_bolt_d}","via":"harvest"}}]},"cross_bolt_above_bore":{"label":"The cross-bolt holes' centres above the bore","kind":"length","measurements":[{"id":"family","value":0.6,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{bcm-mcmr-15-handguard.cross_bolt_above_bore}","via":"harvest"}}]},"flare_tip_top":{"label":"The flat tips of the side faces, their upper corner above the bore","kind":"length","measurements":[{"id":"photo","value":0.26,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mcmr-13-handguard 4d10da7d6e2b (BCM's gallery for the Flat Dark Earth MCMR-13, MCMR_13_FDE: the handguard alone, its right side seen from about 18° above, 2000 x 1334)","scaleRef":"its own rail's pitch (116.0 px/in), the side face 1.0205 nearer; the rail's far top edge at row 533.5 and the side row's centre line at row 709.5 for the angle (18.6°)","method":"the front boundary of the handguard's own colour, row by row: it stands at px 1796 to 1791 from row 680 to row 745; the upper corner (1796, 680) on the side face is 0.263 above the bore","via":"harvest"}}],"note":"The side face's own upper edge is 0.311 above the bore (a regular octagon 1.5 across): the tips' upper corners are cut a little under it, as the 15's are (0.25). BCM's photo of the black one reads 0.24 and Dirty Bird's 0.23."},"flare_tip_bottom":{"label":"The flat tips of the side faces, their lower corner above the bore (negative: below it)","kind":"length","measurements":[{"id":"photo","value":-0.32,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mcmr-13-handguard 4d10da7d6e2b (BCM's gallery for the Flat Dark Earth MCMR-13, MCMR_13_FDE: the handguard alone, its right side seen from about 18° above, 2000 x 1334)","scaleRef":"its own rail's pitch (116.0 px/in), the side face 1.0205 nearer; the angle as for the upper corner","method":"the lower corner (1791, 745), where the front boundary turns back toward the bottom: 0.318 below the bore on the side face","via":"harvest"}}],"note":"The side face's own lower edge is 0.311 below the bore. BCM's photo of the black one reads -0.33 and Dirty Bird's -0.33."},"flare_face_bottom":{"label":"Where the square front face under the rail's end gives way to the slope down to the tips, above the bore","kind":"length","measurements":[{"id":"photo","value":0.74,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/bcm-mcmr-13-handguard 4d10da7d6e2b (BCM's gallery for the Flat Dark Earth MCMR-13, MCMR_13_FDE: the handguard alone, its right side seen from about 18° above, 2000 x 1334)","scaleRef":"its own rail's pitch (116.0 px/in); the angle as for the tips","method":"the front boundary stands at px 1758 to 1760 from the rail's side down to row 611, then runs out to the tip: the corner (1759.5, 611), taken on the neck's wall (half the neck's width from the middle), is 0.745 above the bore and 0.01 in ahead of the rail's front end, one plane with it","via":"harvest"}}],"note":"In the neck, just over where the upper faces end (neck_base_above_bore, 0.71), as on the 15 (0.715 by its level outline). BCM's photo of the black one reads 0.74 and Dirty Bird's 0.74. The same reading on the 15's photo is 0.05 over its level outline, so this may be as much high."},"flare_bottom_run":{"label":"How far behind the tips the bottom flat ends","kind":"length","measurements":[{"id":"photo","value":0.35,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/bcm-mcmr-13-handguard 4d10da7d6e2b (BCM's gallery for the Flat Dark Earth MCMR-13, MCMR_13_FDE: the handguard alone, its right side seen from about 18° above, 2000 x 1334)","scaleRef":"its own rail's pitch (116.0 px/in); the tips at the side face's scale, the bottom flat's near edge at the rail's own (it stands as far from the lens as the rail's far edge does, seen from there)","method":"the front boundary below the tips runs back 8.5 px in 5 rows to the bottom flat's near edge (row 777) at px 1738: 0.349 in behind the tips' true place","via":"harvest"}}],"note":"BCM's photo of the black one reads 0.33 and Dirty Bird's 0.41. The same reading on the 15's photo is 0.05 under its level outline (0.36 against 0.41)."}}},{"subject":"bcm-mcmr-15-handguard","title":"BCM MCMR-15 M-LOK Compatible Modular Rail (BCM-MCMR-15-556-BLK)","dimensions":{"weight":{"label":"Weight on the rifle (the handguard and its mounting hardware)","kind":"mass","measurements":[{"id":"sum","value":11.5,"unit":"oz","pm":0.1,"source":{"type":"derived","expr":"{.weight_handguard} + {.weight_hardware}","via":"harvest"}},{"id":"primary-arms","value":11.5,"unit":"oz","pm":0.05,"stated":"Weight 11.5 Oz","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Bravo Company Manufacturing MCMR Free Float AR-15 Handguard - M-LOK - 15\" (BCM-MCMR-15-556-BLK), specifications","url":"https://www.primaryarms.com/bcm-15-mlok-compatible-modular-rail-bcm-mcmr-15-556-blk","retrieved":"2026-10-05","via":"harvest"}}],"adopt":{"from":"sum","reason":"The maker's two figures; the seller's one figure is their sum."},"note":"BCM gives the two apart; what goes on the rifle is both. Whether the steel barrel nut is in the 2.3 oz of hardware BCM doesn't say in so many words: Primary Arms' one figure for the product is their sum."},"weight_handguard":{"label":"Weight, the handguard alone","kind":"mass","measurements":[{"id":"bcm","value":9.2,"unit":"oz","pm":0.05,"stated":"Handguard alone weighs 9.2 oz","source":{"type":"spec","publisher":"manufacturer","name":"Bravo Company USA, BCM® MCMR-15 (M-LOK® Compatible* Modular Rail) (BCM-MCMR-15-556-BLK), Description","url":"https://bravocompanyusa.com/bcm-mcmr-15-m-lok-compatible-modular-rail/","retrieved":"2026-10-05","via":"harvest"}}]},"weight_hardware":{"label":"Weight, its mounting hardware","kind":"mass","measurements":[{"id":"bcm","value":2.3,"unit":"oz","pm":0.05,"stated":"Handguard mounting hardware 2.3 oz","source":{"type":"spec","publisher":"manufacturer","name":"Bravo Company USA, BCM® MCMR-15 (M-LOK® Compatible* Modular Rail) (BCM-MCMR-15-556-BLK), Description","url":"https://bravocompanyusa.com/bcm-mcmr-15-m-lok-compatible-modular-rail/","retrieved":"2026-10-05","via":"harvest"}}],"note":"The manual's bill of materials: the barrel nut, two clamp blocks, the index plate and the two cross bolts."},"length":{"label":"Length, end to end (the rear end to the tips of the flare)","kind":"length","measurements":[{"id":"bcm","value":15,"unit":"in","pm":0.05,"stated":"Actual length when measured to flare is 15.0\"","source":{"type":"spec","publisher":"manufacturer","name":"Bravo Company USA, BCM® MCMR-15 (M-LOK® Compatible* Modular Rail) (BCM-MCMR-15-556-BLK), Description","url":"https://bravocompanyusa.com/bcm-mcmr-15-m-lok-compatible-modular-rail/","retrieved":"2026-10-05","via":"harvest"}},{"id":"photo","value":15.03,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-mcmr-15-handguard 3c44f96c9c21 (BCM's gallery for the Flat Dark Earth MCMR-15, MCMR_15_FDE: the handguard alone, its right side seen from about 20° above, 2000 x 1333)","scaleRef":"its own top rail's 36 slots at the Picatinny pitch (std.picatinny.slot_pitch): each column read as a rail coordinate between the slot centres; the side faces' M-LOK row (pitch 186.3 px for 40 mm) for what stands at their depth, k 1.0205","method":"the silhouette's two ends (px 114 and 1892) as rail coordinates -1.986 and 36.937, each brought to its true place about the image's centre: -1.598 and 36.545 pitches. Rifle Supply's photo 513799b7a6bd reads 15.07 and Dirty Bird's dd246b2375ad 15.05 the same way (.cache/batch123/bcm-mcmr-15-handguard/ruler.py)","via":"harvest"}}],"adopt":{"from":"bcm","reason":"The maker's figure; three photos read 0.03 to 0.07 more, within what its one decimal and their ± allow."},"note":"BCM's \"to flare\" is the whole length: the side faces run forward into two points (the flare), 0.6 in past the rail's last slot. The photos read 15.03 to 15.07 at the scale of the side faces, where both ends are."},"width":{"label":"Width across the flats (3 to 9 o'clock)","kind":"length","measurements":[{"id":"bcm","value":1.5,"unit":"in","pm":0.05,"stated":"1.5\" Wide","source":{"type":"spec","publisher":"manufacturer","name":"Bravo Company USA, BCM® MCMR-15 (M-LOK® Compatible* Modular Rail) (BCM-MCMR-15-556-BLK), Description","url":"https://bravocompanyusa.com/bcm-mcmr-15-m-lok-compatible-modular-rail/","retrieved":"2026-10-05","via":"harvest"}}]},"height":{"label":"Height (the rail's top to the bottom flat)","kind":"length","measurements":[{"id":"photo","value":1.944,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-mcmr-15-handguard 13f345fa4b4e (Primary Arms' gallery, BCM-MCMR-15-556-BLK_01: the handguard alone, its right side seen level, 1152 x 768)","scaleRef":"its own rail's slots, column by column: the pitch beside each column (29.0 to 29.6 px through the image's middle: 74 to 75 px/in)","method":"ten columns through the image's middle (x 498 to 762), each through a tooth: its top edge to the bottom edge at the 50% level, 144.2 to 144.8 px, 1.926 to 1.956 in at the pitch beside it; toward the photo's ends the same reading runs to 2.02, the pitch there shrinking faster than the heights do (.cache/batch123/bcm-mcmr-15-handguard/heights.py)","via":"harvest"}}],"note":"Not published. From the middle of the side faces' slots the top reads 1.196 above and the bottom 0.758 below: a regular octagon 1.5 in across the flats about the bore puts the bottom at 0.75."},"inside_diameter":{"label":"Inside diameter","kind":"length","measurements":[{"id":"bcm","value":1.3,"unit":"in","pm":0.05,"stated":"1.3\" Inside Diameter","source":{"type":"spec","publisher":"manufacturer","name":"Bravo Company USA, BCM® MCMR-15 (M-LOK® Compatible* Modular Rail) (BCM-MCMR-15-556-BLK), Description","url":"https://bravocompanyusa.com/bcm-mcmr-15-m-lok-compatible-modular-rail/","retrieved":"2026-10-05","via":"harvest"}},{"id":"primary-arms","value":1.3,"unit":"in","pm":0.005,"stated":"Inner Diameter 1.30 in","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Bravo Company Manufacturing MCMR Free Float AR-15 Handguard - M-LOK - 15\" (BCM-MCMR-15-556-BLK), specifications","url":"https://www.primaryarms.com/bcm-15-mlok-compatible-modular-rail-bcm-mcmr-15-556-blk","retrieved":"2026-10-05","via":"harvest"}}],"adopt":{"from":"bcm","reason":"The maker's; the seller repeats it."},"note":"The round bore at its rear end, which goes over the barrel nut. Ahead of it the inside follows the outside (Primary Arms' three-quarter view of the muzzle end, 0e53fbf9dd91, shows flat inner walls): the model takes 1.3 in across the inner flats."},"receiver_gap":{"label":"The gap left between its rear end and the upper receiver","kind":"length","measurements":[{"id":"bcm","value":0.0225,"unit":"in","pm":0.0175,"stated":"NEVER seat the handguard down firmly against the upper-receiver. Because of the tolerances of the upper receiver, a small gap will likely remain between the upper receiver and the handguard. A minimum gap of .005\" should exist to maintain the free-float of the barrel. Note: The gap should not exceed .040\".","source":{"type":"spec","publisher":"manufacturer","name":"BCM, Installation Manual for BCM KMR Series Handguards (KMR-A, MCMR, QRF), Rev. 4/21, page 2, step 14","url":"https://bravocompanymfg.com/downloads/kmr_installation_instructions.pdf","retrieved":"2026-10-05","via":"harvest"}}],"note":"The middle of BCM's range, with half the range as its ±."},"rear_x":{"label":"Its rear end against the receiver's front face (negative: behind it)","kind":"length","measurements":[{"id":"derived","value":-0.4225,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"0in - {std.ar15.upper_barrel_thread_length} + {.receiver_gap}","via":"harvest"}},{"id":"installed","value":-0.433,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-urg-mid-16-mcmr-15 00fe2ff36ca3 (Primary Arms' gallery for the complete upper BCM-URG-MID-16-MCMR-15, _02: its left side seen level, 2200 x 1467)","scaleRef":"the receiver's two lug holes (px 2032.3, 810.4 and 1515.8, 810.7), std.ar15.pin_spacing apart: 81.02 px/in; the receiver's own 13 rail slots read 0.395 a pitch on it","method":"the handguard's rearmost rail slot's centre 7.226 in ahead of the takedown hole, less this ledger's rail_slot0_from_rear (0.623, BCM's photo of the handguard alone) and the receiver's front face (std.ar15.upper_front_face_x, 7.036) (.cache/batch123/bcm-mcmr-15-handguard/urg_rail.py)","via":"harvest"},"note":"A check through two photos, each with its own ±."}],"adopt":{"from":"derived","reason":"BCM's own rule for where it stops; the photos of the complete upper put it within 0.01 in of that."},"note":"It slides back over its barrel nut to the receiver's front shoulder, where the barrel-nut thread begins (std.ar15.upper_barrel_thread_length behind the front face), less the gap BCM's manual asks for. Its rail's rear end and its body's are one plane (BCM's and Rifle Supply's photos: within 0.02 in)."},"barrel_max_od":{"label":"The largest barrel its barrel nut goes over","kind":"length","measurements":[{"id":"bcm","value":1,"unit":"in","pm":0.05,"stated":"The barrel nut will fit over all mil-spec diameter barrels (max of 1\")","source":{"type":"spec","publisher":"manufacturer","name":"Bravo Company USA, BCM® MCMR-15 (M-LOK® Compatible* Modular Rail) (BCM-MCMR-15-556-BLK), Description","url":"https://bravocompanyusa.com/bcm-mcmr-15-m-lok-compatible-modular-rail/","retrieved":"2026-10-05","via":"harvest"}}]},"rail_top_above_bore":{"label":"Its rail's top above the bore axis","kind":"length","measurements":[{"id":"photo","value":1.2,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-mcmr-15-handguard 13f345fa4b4e (Primary Arms' gallery, BCM-MCMR-15-556-BLK_01: the handguard alone, its right side seen level, 1152 x 768)","scaleRef":"its own rail's slots, column by column: the pitch beside each column (29.0 to 29.6 px through the image's middle: 74 to 75 px/in)","method":"the same columns: the tooth tops above the middle of the light showing through the side faces' slots (the axis of a tube with flats at 3 and 9 o'clock): 1.18 to 1.20 in, median 1.196; the ± covers the rail's near or far edge being the one seen (1% either way from 30 in) (heights.py)","via":"harvest"}},{"id":"installed","value":1.217,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-urg-mid-16-mcmr-15 00fe2ff36ca3 (Primary Arms' gallery for the complete upper BCM-URG-MID-16-MCMR-15, _02: its left side seen level, 2200 x 1467)","scaleRef":"the receiver's two lug holes, std.ar15.pin_spacing apart: 81.02 px/in","method":"the handguard rail's tooth tops over its first six inches (7.9 to 14 in ahead of the takedown hole), 2.094 in above the line through the lug holes, less the bore's height above it (std.ar15.bore_axis_y, 0.8775); the receiver's own tooth tops read 2.082, a pixel lower (urg_rail.py)","via":"harvest"}}],"adopt":{"from":"photo","reason":"The handguard's own photo, from its own axis; the installed reading agrees within its ±."},"note":"Its tube is taken to be about the bore (it clamps round its barrel nut). On the complete upper its rail's tooth tops read level with the receiver's within a pixel (2.094 against 2.082 above the pin line, 81 px/in). BCM's own two photos of the complete upper, at 55 px/in and with a scale that runs 3% along the rail, read both rails 2.04 to 2.06."},"rail_slots":{"label":"Slots in its top rail","kind":"count","measurements":[{"id":"photo","value":36,"unit":"count","source":{"type":"photo","photo":"references/bcm-mcmr-15-handguard 3c44f96c9c21 (BCM's gallery for the Flat Dark Earth MCMR-15, MCMR_15_FDE: the handguard alone, its right side seen from about 20° above, 2000 x 1333)","scaleRef":"none: a count","method":"the notches between the teeth along the top edge, each 45.7 px from the next: 36; the same count on Rifle Supply's (513799b7a6bd), Dirty Bird's (dd246b2375ad) and Primary Arms' (13f345fa4b4e) photos. The marks in the slots run T14 (rearmost) to T48, the frontmost slot unmarked","via":"harvest"}}]},"rail_slot0_from_rear":{"label":"Its rail's rearmost slot (its centre) ahead of its rear end","kind":"length","measurements":[{"id":"bcm-photo","value":0.623,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bcm-mcmr-15-handguard 3c44f96c9c21 (BCM's gallery for the Flat Dark Earth MCMR-15, MCMR_15_FDE: the handguard alone, its right side seen from about 20° above, 2000 x 1333)","scaleRef":"its own top rail's 36 slots at the Picatinny pitch (std.picatinny.slot_pitch): each column read as a rail coordinate between the slot centres","method":"the rear end of the rail's top edge (the first column whose silhouette top is within 4 px of the tooth tops, px 132.5): 1.582 pitches behind the first slot's centre (.cache/batch123/bcm-mcmr-15-handguard/railfront.py)","via":"harvest"}},{"id":"rifle-supply-photo","value":0.625,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bcm-mcmr-15-handguard 513799b7a6bd (Rifle Supply's gallery, 173586952: the black handguard alone, its left side seen from about 18° above, 2000 x 2000)","scaleRef":"its own top rail's 36 slots at the Picatinny pitch (std.picatinny.slot_pitch): each column read as a rail coordinate between the slot centres","method":"the same edge (mirrored px 167.5): 1.585 pitches behind the first slot's centre","via":"harvest"}},{"id":"dirty-bird-photo","value":0.641,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-mcmr-15-handguard dd246b2375ad (Dirty Bird's gallery, the 15 in black: its left side from above, 1142 x 845)","scaleRef":"its own top rail's 36 slots at the Picatinny pitch (std.picatinny.slot_pitch): each column read as a rail coordinate between the slot centres","method":"the same edge (mirrored px 42.5): 1.627 pitches behind the first slot's centre, at 71 px/in","via":"harvest"}}],"adopt":{"from":"bcm-photo","reason":"The maker's own photograph at the largest scale; the other two read 0.002 and 0.018 more."},"note":"Read to the rail's own rear end, along the far edge of its top, which is where the slots are read: nothing to bring to another depth. The body's rear end is the same plane as far as the photos show (the silhouette's rearmost point, on the near side, reads 0.63 to 0.69 behind the slot by what is taken for its depth). Installed, the slot reads 7.226 in ahead of the takedown pin, which with rear_x makes this 0.61."},"rail_slot0_x":{"label":"Its rail's rearmost slot (its centre) ahead of the receiver's front face","kind":"length","measurements":[{"id":"installed","value":0.19,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-urg-mid-16-mcmr-15 00fe2ff36ca3 (Primary Arms' gallery for the complete upper BCM-URG-MID-16-MCMR-15, _02: its left side seen level, 2200 x 1467)","scaleRef":"the receiver's two lug holes (px 2032.3, 810.4 and 1515.8, 810.7), std.ar15.pin_spacing apart: 81.02 px/in; the receiver's own 13 rail slots read 0.395 a pitch on it","method":"the gaps between the teeth 0.06 in below the tooth tops, each edge at the 50% level: the handguard's first slot's centre 7.226 in ahead of the takedown hole, less the receiver's front face (std.ar15.upper_front_face_x, 7.036). BCM's own two photos of the complete upper (a0e4baef2a6d, 12dd68abe371; 55 and 57 px/in) read 7.223 and 7.225 (urg_rail.py)","via":"harvest"}},{"id":"through-rear","value":0.2005,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.rear_x} + {.rail_slot0_from_rear}","via":"harvest"}}],"adopt":{"from":"installed","reason":"Read where it matters, in the receiver's own frame on three photos; the other goes through the handguard's rear end, which the gap at the receiver moves."}},"rail_front_from_last_slot":{"label":"Its rail's front end ahead of its last slot's centre","kind":"length","measurements":[{"id":"photo","value":0.283,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bcm-mcmr-15-handguard 3c44f96c9c21 (BCM's gallery for the Flat Dark Earth MCMR-15, MCMR_15_FDE: the handguard alone, its right side seen from about 20° above, 2000 x 1333)","scaleRef":"its own top rail's 36 slots at the Picatinny pitch (std.picatinny.slot_pitch): each column read as a rail coordinate between the slot centres","method":"the front end of the rail's top edge (the last column whose silhouette top is within 4 px of the tooth tops, px 1836.5): 0.718 pitches ahead of the last slot's centre. Rifle Supply's photo reads 0.294 and Dirty Bird's 0.305 the same way (railfront.py)","via":"harvest"}}],"note":"A slot's half width and one land of about the standard's width. The flare's tips are 0.32 in further forward."},"mlok_side_slots":{"label":"M-LOK slots on each side face (3 and 9 o'clock)","kind":"count","measurements":[{"id":"photo","value":8,"unit":"count","source":{"type":"photo","photo":"references/bcm-mcmr-15-handguard 3c44f96c9c21 (BCM's gallery for the Flat Dark Earth MCMR-15, MCMR_15_FDE: the handguard alone, its right side seen from about 20° above, 2000 x 1333)","scaleRef":"none: a count","method":"the slots of the lower row in the photo (the 3 o'clock face), 186.5 px apart; eight on the 9 o'clock face in Rifle Supply's photo (513799b7a6bd), and eight on Primary Arms' level photo (13f345fa4b4e)","via":"harvest"}}]},"mlok_side_slot0_from_rail_slot0":{"label":"The side faces' rearmost M-LOK slot (its centre) ahead of the rail's rearmost slot's centre","kind":"length","measurements":[{"id":"photo","value":2.342,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-mcmr-15-handguard 3c44f96c9c21 (BCM's gallery for the Flat Dark Earth MCMR-15, MCMR_15_FDE: the handguard alone, its right side seen from about 20° above, 2000 x 1333)","scaleRef":"its own top rail's 36 slots at the Picatinny pitch (std.picatinny.slot_pitch): each column read as a rail coordinate between the slot centres; the row's own pitch gives k 1.0205","method":"the eight slots' sixteen ends fitted to one pitch and one length (rms 0.006 in): the first slot's rear end at rail coordinate 4.078, true 4.345 pitches (1.7117 in), plus half the standard's slot (std.mlok.slot_length). Rifle Supply's photo reads 1.7115 and Dirty Bird's 1.7115 for the same end (ruler.py)","via":"harvest"}}],"note":"5.94 rail pitches: the M-LOK slots' centres fall on the rail's slots' (every fourth), within 0.02 in."},"mlok_diag_slots":{"label":"M-LOK slots on each face between (1:30, 4:30, 7:30 and 10:30)","kind":"count","measurements":[{"id":"photo","value":8,"unit":"count","source":{"type":"photo","photo":"references/bcm-mcmr-15-handguard 13f345fa4b4e (Primary Arms' gallery, BCM-MCMR-15-556-BLK_01: the handguard alone, its right side seen level, 1152 x 768)","scaleRef":"none: a count","method":"the upper and the lower row of the level photo (the 1:30 and 4:30 faces), eight each and at the same columns (169.5 to 989.5 px for their rear ends, both rows); eight on the 1:30 face in BCM's photo (3c44f96c9c21) and on the 10:30 face in Rifle Supply's","via":"harvest"}}]},"mlok_diag_slot0_from_rail_slot0":{"label":"The between faces' rearmost M-LOK slot (its centre) ahead of the rail's rearmost slot's centre","kind":"length","measurements":[{"id":"photo","value":1.952,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-mcmr-15-handguard 3c44f96c9c21 (BCM's gallery for the Flat Dark Earth MCMR-15, MCMR_15_FDE: the handguard alone, its right side seen from about 20° above, 2000 x 1333)","scaleRef":"its own top rail's 36 slots at the Picatinny pitch (std.picatinny.slot_pitch): each column read as a rail coordinate between the slot centres; the row's own pitch gives k 1.0193","method":"the eight slots' sixteen ends fitted to one pitch and one length (rms 0.003 in): the first slot's rear end at rail coordinate 3.085, true 3.355 pitches (1.3218 in), plus half the standard's slot. Rifle Supply's photo reads 1.3171 and Dirty Bird's 1.3163 for the same end","via":"harvest"}}],"note":"One rail pitch behind the side faces' row (0.390 here against 0.394)."},"mlok_side_slot0_x":{"label":"The side faces' rearmost M-LOK slot (its centre) ahead of the receiver's front face","kind":"length","measurements":[{"id":"derived","value":2.532,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.rail_slot0_x} + {.mlok_side_slot0_from_rail_slot0}","via":"harvest"}}]},"mlok_diag_slot0_x":{"label":"The between faces' rearmost M-LOK slot (its centre) ahead of the receiver's front face","kind":"length","measurements":[{"id":"derived","value":2.142,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.rail_slot0_x} + {.mlok_diag_slot0_from_rail_slot0}","via":"harvest"}}]},"mlok_bottom_front_from_side_front":{"label":"The underside's foremost M-LOK slot (its centre) ahead of the side faces' foremost slot's","kind":"length","measurements":[{"id":"photo","value":0.007,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-kag-mlok b9ff51bbaa16 (BCM's gallery for its KAG, BCM-KAG-MCMR-BLK-5: the KAG on an MCMR's underside, from a little below the rifle's right side, muzzle to the lower right, 1500 x 1000)","scaleRef":"M-LOK's 32 mm slot (std.mlok.slot_length) on the faces beside it: the side face's foremost slot's rim 181 px long, the 4:30 face's beside it 174 px; 139 px to the inch","method":"the photo turned 31.75° about (850, 650) to level the handguard's lower edge (a line through 142 columns, rms 0.3 px). Along that edge the underside's band is dark from 648 to 733 px and from 782 to 952 (170 px, a 32 mm slot; the bright web between, 49 px, is M-LOK's 8 mm), the front run ending where the muzzle end's slope begins (954); on a row through the side face's foremost slot its rim runs 774 to 955. The two centres stand 1 px apart, the underside's ahead. The 4:30 face's slot above, 722 to 896, is 55.5 px (0.40 in, one rail pitch) behind both. The lens stood square to the rail there (light shows through that slot to the far face along its whole length), so the underside's depth behind the side face moves it along the rail by less than the ±, which covers each end read to 2 px and the scale. (.cache/mcmr-under/level.py, edge2.py and rows.py in the main checkout)","via":"harvest"}}],"note":"In line with the side rows, and so one rail pitch (10 mm) ahead of the faces' between, as the side rows are: the underside's row is staggered as the side faces' is. BCM's photo of its Vertical Grip Mod 3 on an MCMR (references/bcm-vertical-grip-mod-3-mlok c03d3a91bf0d, -6) was taken from a little higher, and its lower edge is the corner below the 4:30 face: no slot of the underside shows in it. On the KAG's photo that slot ends within 2 px (0.015 in) of where the bottom flat ends and the muzzle end's slope begins. This length's figures put the flat's end 0.025 in behind the slot's front end, which the model cuts on into the slope's foot (the flat's end is the level outline's, 0.41 in behind the tips; read as the 13's and the 10's are read, this length's photo gives 0.36, which would leave 0.025 in of flat ahead of the slot)."},"mlok_bottom_slots":{"label":"M-LOK slots on the underside (6 o'clock)","kind":"count","measurements":[{"id":"assumed","value":8,"unit":"count","source":{"type":"derived","expr":"{.mlok_side_slots}","basis":"An assumption for the drawing, not a reading: the underside's row is read at its front end only, in line with the side faces' foremost slot and with the next behind it in line with theirs (mlok_bottom_front_from_side_front); where it ends at the rear shows in no view on file or found, and the side faces' count is taken.","via":"harvest"}}]},"mlok_bottom_slot0_x":{"label":"The underside's rearmost M-LOK slot (its centre) ahead of the receiver's front face","kind":"length","measurements":[{"id":"derived","value":2.539,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.mlok_side_slot0_x} + ({.mlok_side_slots} - {.mlok_bottom_slots}) * {std.mlok.slot_pitch} + {.mlok_bottom_front_from_side_front}","via":"harvest"}}]},"reach_inside":{"label":"The room inside its faces, from a face in to the barrel (what an M-LOK accessory's nuts may take)","kind":"length","measurements":[],"note":"Not sourced: it depends on the barrel and gas block under it, other parts. Its wall is 0.1 in by BCM's two figures (1.5 wide, 1.3 inside)."},"rail_body_height":{"label":"The rail's depth, its top to where the neck's wall begins","kind":"length","measurements":[{"id":"photo","value":0.215,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-mcmr-15-handguard 13f345fa4b4e (Primary Arms' gallery, BCM-MCMR-15-556-BLK_01: the handguard alone, its right side seen level, 1152 x 768)","scaleRef":"its own rail's pitch beside the column (28.6 px: 72.6 px/in)","method":"a column clear of holes (x 140): the teeth and the rail's side from row 297 to 312 (16 rows), the last six of them the dark band of its underside's slope; the neck's lit wall begins at row 313","via":"harvest"}}],"note":"Since 2026-10-12 the model's rail meets the neck's walls 0.177 in under its top: where the standard's lower faces, carried on at their 45 degrees, reach a neck as wide as neck_width has it (0.70 in). That is 0.038 in short of this reading, outside its ±. A neck 0.63 in wide would put it here, and BCM's own diagram draws 0.61 (neck_width's note): the neck's width is the open figure, and an end view is what is asked for. The inside's roof is still drawn a wall under this height."},"rail_bevel":{"label":"The slope under the rail's edges, its height as seen from the side","kind":"length","measurements":[{"id":"photo","value":0.08,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-mcmr-15-handguard 13f345fa4b4e (Primary Arms' gallery, BCM-MCMR-15-556-BLK_01: the handguard alone, its right side seen level, 1152 x 768)","scaleRef":"its own rail's pitch beside the column (28.6 px: 72.6 px/in)","method":"the dark band under the rail's widest line, rows 307 to 312 (six rows) at x 140","via":"harvest"}}],"note":"A reading of the photo, and since 2026-10-12 not what the rail is drawn by: its head is the standard's in section (std.picatinny.*, in the ledger since 2026-10-05; pipeline/blender/lib.py rail_head), whose lower faces run from 0.1105 in under the top in to the neck's walls, 0.066 in as seen from the side: inside this reading's ±. Until then both of the rail's edges were sloped by this figure, the standard's own section not being in the ledger: a flat 0.02 in too wide and lower faces 0.024 in outside the standard's, in both of which every clamp stood. The builder still finds the rail's front end in the traced outline by it."},"neck_base_above_bore":{"label":"Where the upper faces end and the neck under the rail begins, above the bore","kind":"length","measurements":[{"id":"photo","value":0.71,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mcmr-15-handguard 13f345fa4b4e (Primary Arms' gallery, BCM-MCMR-15-556-BLK_01: the handguard alone, its right side seen level, 1152 x 768)","scaleRef":"its own rail's pitch beside the column (28.6 px: 72.6 px/in), 1% more for the near wall","method":"a column clear of slots and holes (x 140): the dark line where the upper face meets the neck's wall at row 333.5, 52.4 px above the line through the middles of the side faces' slots","via":"harvest"}}]},"neck_width":{"label":"The neck's width under the rail","kind":"length","measurements":[{"id":"derived","value":0.7013,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"2 * ({.width} / 2 + {.width} / 2 * 0.41421356 - {.neck_base_above_bore})","via":"harvest"},"note":"0.41421356 is tan 22.5°: half a regular octagon's face over its half width."}],"note":"No view shows it square on. Where a 45° face of a regular octagon 1.5 in across reaches neck_base_above_bore it is 0.35 in from the middle. BCM's own diagram of the section (98845584f4fa, undimensioned) draws the neck 0.61 in wide to its 1.5 in body. And the rail's lower faces, the standard's since 2026-10-12, reach a neck this wide 0.177 in under the rail's top, where the side photo has the neck's wall begin 0.215 ± 0.02 under it (rail_body_height): a neck 0.63 in wide would agree with the photo, the standard and the diagram."},"hole_center_above_bore":{"label":"The lightening holes under the rail, their centres above the bore","kind":"length","measurements":[{"id":"photo","value":0.76,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mcmr-15-handguard 13f345fa4b4e (Primary Arms' gallery, BCM-MCMR-15-556-BLK_01: the handguard alone, its right side seen level, 1152 x 768)","scaleRef":"its own rail's slots, column by column: the pitch beside each column (29.0 to 29.6 px through the image's middle: 74 to 75 px/in)","method":"the light showing through twelve holes from side to side, through the image's middle: its centre 0.745 to 0.771 in above the line through the middles of the side faces' slots (median 0.755); a lens a few degrees above level sees the far wall's holes lower, which would put the near wall's up to 0.025 higher (heights2.py)","via":"harvest"}}]},"hole_pitch":{"label":"The lightening holes' pitch (oblong to oblong, round to round)","kind":"length","measurements":[{"id":"photo","value":0.788,"unit":"in","pm":0.003,"source":{"type":"photo","photo":"references/bcm-mcmr-15-handguard 3c44f96c9c21 (BCM's gallery for the Flat Dark Earth MCMR-15, MCMR_15_FDE: the handguard alone, its right side seen from about 20° above, 2000 x 1333)","scaleRef":"its own top rail's 36 slots at the Picatinny pitch (std.picatinny.slot_pitch): each column read as a rail coordinate between the slot centres","method":"the first and the sixteenth oblong hole at rail coordinates 3.917 and 33.926 (true, k 1.018): 2.0006 pitches apart on average (holes.py)","via":"harvest"}}],"note":"Two rail pitches: an oblong hole and a round one by turns, one rail pitch apart."},"hole_count":{"label":"Lightening holes of each kind on each side","kind":"count","measurements":[{"id":"photo","value":16,"unit":"count","source":{"type":"photo","photo":"references/bcm-mcmr-15-handguard 3c44f96c9c21 (BCM's gallery for the Flat Dark Earth MCMR-15, MCMR_15_FDE: the handguard alone, its right side seen from about 20° above, 2000 x 1333)","scaleRef":"none: a count","method":"sixteen oblong holes from rail coordinate 3.92 to 33.93, a round one ahead of each (the last at 34.85, the rail's front end just ahead of it)","via":"harvest"}}]},"hole_oblong0_from_rail_slot0":{"label":"The rearmost oblong hole (its centre) ahead of the rail's rearmost slot's centre","kind":"length","measurements":[{"id":"photo","value":1.543,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-mcmr-15-handguard 3c44f96c9c21 (BCM's gallery for the Flat Dark Earth MCMR-15, MCMR_15_FDE: the handguard alone, its right side seen from about 20° above, 2000 x 1333)","scaleRef":"its own top rail's 36 slots at the Picatinny pitch (std.picatinny.slot_pitch): each column read as a rail coordinate between the slot centres; k 1.018 for the neck's near wall","method":"the hole's dark outline's centroid at px 372.9: rail coordinate 3.63, true 3.917 pitches (holes.py)","via":"harvest"}}]},"hole_oblong_length":{"label":"An oblong hole's length","kind":"length","measurements":[{"id":"photo","value":0.39,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mcmr-15-handguard 3c44f96c9c21 (BCM's gallery for the Flat Dark Earth MCMR-15, MCMR_15_FDE: the handguard alone, its right side seen from about 20° above, 2000 x 1333)","scaleRef":"the side faces' M-LOK row: 118.0 px/in at the neck's near wall","method":"the first and the last oblong hole's outlines' long axes (second moments): 0.384 and 0.391","via":"harvest"}}]},"hole_oblong_width":{"label":"An oblong hole's width","kind":"length","measurements":[{"id":"photo","value":0.2,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-mcmr-15-handguard 3c44f96c9c21 (BCM's gallery for the Flat Dark Earth MCMR-15, MCMR_15_FDE: the handguard alone, its right side seen from about 20° above, 2000 x 1333)","scaleRef":"the side faces' M-LOK row: 118.0 px/in at the neck's near wall","method":"the same two outlines' short axes: 0.203 and 0.195","via":"harvest"}}]},"hole_oblong_slant":{"label":"An oblong hole's slant from the rail's line (its top toward the muzzle)","kind":"angle","measurements":[{"id":"photo","value":58,"unit":"deg","pm":5,"source":{"type":"photo","photo":"references/bcm-mcmr-15-handguard 3c44f96c9c21 (BCM's gallery for the Flat Dark Earth MCMR-15, MCMR_15_FDE: the handguard alone, its right side seen from about 20° above, 2000 x 1333)","scaleRef":"none: an angle in the image, the rail level in it within 0.03°","method":"the same two outlines' long axes: 56° and 60° from the rail's line, as seen from 20° above (which steepens a slant by a degree or two)","via":"harvest"}}]},"hole_round_d":{"label":"A round lightening hole's diameter","kind":"length","measurements":[{"id":"photo","value":0.19,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-mcmr-15-handguard 3c44f96c9c21 (BCM's gallery for the Flat Dark Earth MCMR-15, MCMR_15_FDE: the handguard alone, its right side seen from about 20° above, 2000 x 1333)","scaleRef":"the side faces' M-LOK row: 118.0 px/in at the neck's near wall","method":"nine round holes' outlines: 0.20 to 0.22 along the rail (the wall's thickness shows in it), 0.17 to 0.18 across as seen from 20° above (0.18 to 0.19 square on)","via":"harvest"}}]},"cross_bolt0_from_rail_slot0":{"label":"The rear cross-bolt hole (its centre) ahead of the rail's rearmost slot's centre","kind":"length","measurements":[{"id":"photo","value":0.152,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-mcmr-15-handguard 3c44f96c9c21 (BCM's gallery for the Flat Dark Earth MCMR-15, MCMR_15_FDE: the handguard alone, its right side seen from about 20° above, 2000 x 1333)","scaleRef":"its own top rail's 36 slots at the Picatinny pitch (std.picatinny.slot_pitch): each column read as a rail coordinate between the slot centres; k 1.018","method":"the hole's dark outline's centroid at px 208.5: true rail coordinate 0.386 pitches (holes.py)","via":"harvest"}}]},"cross_bolt_spacing":{"label":"The two cross-bolt holes, centre to centre","kind":"length","measurements":[{"id":"photo","value":0.217,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-mcmr-15-handguard 3c44f96c9c21 (BCM's gallery for the Flat Dark Earth MCMR-15, MCMR_15_FDE: the handguard alone, its right side seen from about 20° above, 2000 x 1333)","scaleRef":"its own top rail's 36 slots at the Picatinny pitch (std.picatinny.slot_pitch): each column read as a rail coordinate between the slot centres","method":"the two outlines' centroids at px 208.5 and 234.2: 0.551 pitches apart","via":"harvest"}}]},"cross_bolt_d":{"label":"A cross-bolt hole's diameter, as it shows","kind":"length","measurements":[{"id":"photo","value":0.18,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-mcmr-15-handguard 3c44f96c9c21 (BCM's gallery for the Flat Dark Earth MCMR-15, MCMR_15_FDE: the handguard alone, its right side seen from about 20° above, 2000 x 1333)","scaleRef":"the side faces' M-LOK row: 118.0 px/in","method":"the two outlines: 0.19 by 0.17 each","via":"harvest"}}]},"cross_bolt_above_bore":{"label":"The cross-bolt holes' centres above the bore","kind":"length","measurements":[{"id":"photo","value":0.6,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-mcmr-15-handguard 13f345fa4b4e (Primary Arms' gallery, BCM-MCMR-15-556-BLK_01: the handguard alone, its right side seen level, 1152 x 768)","scaleRef":"its own rail's pitch beside them (29.5 px: 75 px/in)","method":"the two holes' centres at rows 341.0 and 341.4: 0.598 and 0.597 in above the line through the middles of the side faces' slots; they read 0.16 by 0.17 across here (heights2.py)","via":"harvest"}}]}}},{"subject":"bcm-mid-gas-tube","title":"Bravo Company (BCM) gas tube, mid length (Gas-Tube-Mid-Length)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[],"note":"Not published: BCM's page states none (its product data has \"weight\":null), and no seller's page for it is on file."},"length":{"label":"Length","kind":"length","measurements":[{"id":"bcm","value":11.75,"unit":"in","pm":0.125,"stated":"Length: Approximately 11 3/4\"","source":{"type":"spec","publisher":"manufacturer","name":"Bravo Company, Gas Tube - Mid Length (Gas-Tube-Mid-Length), Description","url":"https://bravocompanyusa.com/gas-tube-mid-length/","retrieved":"2026-10-05","via":"harvest"},"note":"\"Approximately\" is BCM's word, and the figure is given to the quarter inch: the ± is half of that."}]},"od":{"label":"Outside diameter","kind":"length","measurements":[{"id":"tdp","value":0.18,"unit":"in","pm":0.002,"stated":".1800 DIA REF","source":{"type":"standard","doc":"US Army TDP drawing 8448567 (Gas Tube Assembly), PDF page 144, both ends"},"note":"A REF figure, the tube stock's size; .179 is allowed at its bends."}],"note":"BCM gives none; the tube is the standard's (the carrier key's socket takes a .180 tube)."},"bend_offset":{"label":"How far the tube drops at its bend (its rear run above its front)","kind":"length","measurements":[{"id":"tdp","value":0.156,"unit":"in","pm":0.01,"stated":"offset .156","source":{"type":"standard","doc":"US Army TDP drawing 8448567 (Gas Tube Assembly), rev F (the rifle's tube; R 1.50 ±.50); user-supplied scan, PDF page 144","via":"user"}}],"note":"The standard's: it takes the tube from the receiver's .781 above the bore down to a block's hole. Where the bend lies along a mid-length tube has no source for this part (above)."}}},{"subject":"bcm-mk2-buffer-t0","title":"BCM MK2 Buffer Mod 1 - T0","dimensions":{"weight":{"label":"Weight (its class: T0, the lightest of BCM's five MK2 buffers)","kind":"mass","measurements":[{"id":"bcm","value":3.8,"unit":"oz","pm":0.1,"stated":"THE BCM® MK2 BUFFER MOD1- T0, Intermediate Length (BUFFER ONLY) (weight = approximately 3.8oz)","source":{"type":"spec","publisher":"manufacturer","name":"Bravo Company USA, BCM MK2 Buffer Mod 1 - T0 (BCM-BFMK2-M1-T0)","url":"https://bravocompanyusa.com/bcm-mk2-buffer-t0","retrieved":"2026-10-28","via":"harvest"},"note":"\"approximately\": the ± is a tenth, not half the last digit."},{"id":"bcm-kit","value":3.8,"unit":"oz","pm":0.1,"stated":"MK2 Mod 1 - T0 Buffer (weight = approximately 3.8oz)","source":{"type":"spec","publisher":"manufacturer","name":"Bravo Company USA, BCM MK2 Recoil Mitigation System - Mod 1 - T0 (BCM-MK2RMS-M1T0)","url":"https://bravocompanyusa.com/bcm-mk2-recoil-mitigation-system-mod-1-t0/","retrieved":"2026-10-28","via":"harvest"}}],"adopt":{"from":"bcm","reason":"The buffer's own page; the kit's page repeats it."},"note":"BCM's five MK2 Mod 1 buffers, each \"(weight = approximately …oz)\" on its own page (read 2026-10-28): T0 3.8 (BCM-BFMK2-M1-T0), T1 4.7 (BCM-BFMK2-M1-T1), T2 5.6 (BCM-BFMK2-M1-T2), T3 6.5 (BCM-BFMK2-M1-T3), T4 7.4 (BCM-BFMK2-M1-T4). Only the T0 is in the catalog."},"length":{"label":"Length (the head's front face to the bumper's end)","kind":"length","measurements":[{"id":"photo","value":4.046,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-mk2-receiver-extension da2d35d9e02d (BCM's MK2-GFSK-STOCK-KIT-BLK: the Mod 2 stock kit with the MK2 tube, an M16 spring and this buffer laid flat on white, from above, 1000 x 667)","scaleRef":"the MK2 tube beside it, 525.5 px for its 7.955 in (bcm-mk2-receiver-extension.tube_length): 66.06 px/in; at that scale the free spring is 12.48 in (the Army's 12.50) and the head 0.984 (the standard's 0.98)","method":"its silhouette on its axis row (y 566): the bumper's end at x 720.0 (the cream urethane against white, threshold 240) to the head's front face at 987.3: 267.3 px","via":"harvest"},"note":"BCM's photo of the T0 standing upright (references/bcm-mk2-buffer-t0 040474c9f6d0) has it 5.75 body widths long: 4.05 in for the standard 0.687 body, though taken from close by."},{"id":"bcm-drawing","value":4.35,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/bcm-mk2-buffer-t0 43113d288f89 (BCM's BUFFER_ASSY_MK2_INTERMEDIATE: an exploded line drawing of the assembly, 3784 x 4898, on the kit's page)","scaleRef":"its head's 289 px as the standard's 0.98 (a head that runs in the extension's 1.000 bore): 295 px/in","method":"the body from its head's front face (x 25) to its open end (1153), 3.82 in, and the bumper from its shoulder (3600) to its end (3757), 0.53 in, added","via":"harvest"},"note":"BCM's illustration has a thicker head (0.36 in) and a bumper standing 0.53 out, where both photos of the buffer have the standard's 0.25 and 0.4: an illustration, not drawn to the product's proportions."}],"adopt":{"from":"photo","reason":"BCM's photo of the buffer beside the tube, at a scale three published figures bear out (the tube's thread, the Army's spring, the standard head); a second photo agrees. BCM's illustration is 7% longer and its head and bumper are not the photos' proportions."}},"od":{"label":"Diameter (its head, which runs in the extension's bore)","kind":"length","measurements":[{"id":"std","value":0.98,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.carbine_buffer.head_d}","basis":"The standard buffer's head, which runs in the extension's 1.000 bore: BCM's buffer page, \"Comprised of Mil-Spec components\"","via":"harvest"}},{"id":"photo","value":0.984,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-receiver-extension da2d35d9e02d (BCM's stock kit photo on white, 1000 x 667)","scaleRef":"66.06 px/in (length)","method":"the head's silhouette across, x 974 to 984: 65 px","via":"harvest"}}],"adopt":{"from":"std","reason":"The standard head; BCM's photo has it to a pixel."}},"head_thickness":{"label":"The head's thickness (the flange the spring bears on)","kind":"length","measurements":[{"id":"std","value":0.254,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.carbine_buffer.head_thickness}","via":"harvest"}},{"id":"photo","value":0.247,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-receiver-extension da2d35d9e02d (BCM's stock kit photo on white, 1000 x 667)","scaleRef":"66.06 px/in (length)","method":"the head's full-diameter run, x 971 to 987.3: 16.3 px","via":"harvest"}}],"adopt":{"from":"std","reason":"The standard's; BCM's photo agrees within it."}},"collar_d":{"label":"The collar behind the head (what the spring's end coil sits over)","kind":"length","measurements":[{"id":"std","value":0.781,"unit":"in","pm":0.001,"source":{"type":"derived","expr":"{std.carbine_buffer.pilot_d}","via":"harvest"}},{"id":"photo","value":0.772,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-receiver-extension da2d35d9e02d (BCM's stock kit photo on white, 1000 x 667)","scaleRef":"66.06 px/in (length)","method":"the collar's silhouette, x 954 to 968: 51 px; it ends at x 951, 0.55 in behind the face (the standard's body begins at 0.51)","via":"harvest"}}],"adopt":{"from":"std","reason":"The standard's; BCM's photo agrees within it."}},"bumper_exposed":{"label":"How far the bumper stands out of the body","kind":"length","measurements":[{"id":"std","value":0.4,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{std.carbine_buffer.bumper_exposed}","via":"harvest"}},{"id":"photo","value":0.42,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-receiver-extension da2d35d9e02d (BCM's stock kit photo on white, 1000 x 667)","scaleRef":"66.06 px/in (length)","method":"the cream urethane from its end (x 720.0) to the black body (747.8): 27.8 px; its end 34 px across, widening at 13 degrees to the body's","via":"harvest"},"note":"BCM's drawing: \"MIL-SPEC Polyether Urethane Bumper ... Modified to fit Pre-load Spring with Integral Over-travel Stop\": changed inside; outside, its photos have the standard's."}],"adopt":{"from":"std","reason":"The standard bumper's (the Army's drawing); BCM's photo agrees within its ±."}},"body_length":{"label":"The body's length (the head's front face to the body's open end)","kind":"length","measurements":[{"id":"length","value":3.646,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.length} - {.bumper_exposed}","via":"harvest"}},{"id":"photo","value":3.626,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-receiver-extension da2d35d9e02d (BCM's stock kit photo on white, 1000 x 667)","scaleRef":"66.06 px/in (length)","method":"from the head's face (x 987.3) to where the body meets the cream bumper (747.8): 239.5 px","via":"harvest"}}],"adopt":{"from":"length","reason":"The length less the standard bumper's; the photo's own reading agrees within its ±."}},"pin_from_open_end":{"label":"The pin across the body and the bumper: its centre ahead of the body's open end","kind":"length","measurements":[{"id":"photo","value":0.144,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-mk2-buffer-t0 040474c9f6d0 (BCM's photo of the T0 standing upright, 1920 x 1281)","scaleRef":"the body's own width, 167 px, as the standard's 0.687 (std.carbine_buffer.body_d)","method":"the pin hole's centre (y 293) below the body's top end (258): 35 px","via":"harvest"},"note":"The kit photo (da2d35d9e02d) has it 9.4 px from the bumper, 0.142 in. The standard carbine buffer's pin is 0.24 in from its open end (std.carbine_buffer.pin_from_open_end): BCM's bumper is \"Modified to fit Pre-load Spring\"."}]},"pin_d":{"label":"The pin across the body: its diameter","kind":"length","measurements":[{"id":"photo","value":0.09,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-mk2-buffer-t0 040474c9f6d0 (BCM's photo of the T0 standing upright, 1920 x 1281)","scaleRef":"the body's own width, 167 px, as the standard's 0.687","method":"the pin hole's dark ring, 22 px across","via":"harvest"},"note":"Smaller than the standard buffer's .122 pin."}]}}},{"subject":"bcm-mk2-charging-handle","title":"BCM Ambidextrous MK2 Charging Handle, Large Latch (BCM-GFH-MK2-LRG-AMBI)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"faxon","value":0.18,"unit":"lb","stated":"Weight 0.18 lb","source":{"type":"spec","publisher":"retailer","name":"Faxon Firearms, BCM GUNFIGHTER MK2 Ambidextrous Charging Handle - Large Latch - Ships From Sports South (SKU 167850, MPN GFHMK2LRGAMBI, UPC 812526023803), specification row; its description line says \"Weight: 0.18 lb.\"","url":"https://faxonfirearms.com/GFHMK2LRGAMBI","retrieved":"2026-10-05","via":"harvest"}}],"note":"BCM states none (its four MK2 pages, its company site, its brochure). One seller's figure for exactly this product, which doesn't say whether it is the handle's or the package's: a mil-spec handle is 1.1 oz (aero-charging-handle.weight), so 2.9 oz may be a packed weight. Two sellers give \"3 oz\" for the single-sided large handle (BCM-GFH-MK2-LRG: ar15discounts.com, dirtybirdusa.com), another product."},"length":{"label":"The shaft: its shoulder (where the Army's drawing has the T's front face) to the front hook's tip","kind":"length","measurements":[{"id":"standard","value":5.895,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{aero-charging-handle.length}","via":"harvest"},"note":"US Army TDP drawing 8448518 (Handle, Charging), rev G, side view: 5.600 and .295."}],"note":"The standard's, by expression: BCM states no length. \"Compatible with Mil-Spec AR-15 Direct Impingement Weapon Systems.\" (BCM's page): the hook that pulls the carrier is where the standard's is. The handle is placed by it: its tip this far ahead of the receiver's rear face."},"shaft_width":{"label":"The shaft's width","kind":"length","measurements":[{"id":"standard","value":0.4,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{aero-charging-handle.shaft_width}","via":"harvest"},"note":"US Army TDP drawing 8448518, plan view: .400 -B-."}],"note":"The standard's, by expression: the channel it runs in is the standard's. It is the plan photos' scale."},"shaft_thickness":{"label":"The shaft's thickness","kind":"length","measurements":[{"id":"standard","value":0.2985,"unit":"in","pm":0.0035,"source":{"type":"derived","expr":"{aero-charging-handle.shaft_thickness}","via":"harvest"},"note":"US Army TDP drawing 8448518, side view: .2985 ±.0035."}],"note":"The standard's, by expression."},"latch_reach":{"label":"How far a latch stands out past the handle's main body (BCM's figure: taken as from the shaft's side face to the latch's tip, across)","kind":"length","measurements":[{"id":"bcm","value":1.1,"unit":"in","pm":0.05,"stated":"Large latch extends past the main body approximately 1.10\".","source":{"type":"spec","publisher":"manufacturer","name":"BCM, BCM® Ambidextrous MK2 Charging Handle - Large Latch (5.56mm/.223) (BCM-GFH-MK2-LRG-AMBI), About this BCM® MK2 Ambi AR-15 Charging Handle","url":"https://bravocompanyusa.com/bcm-ambidextrous-mk2-charging-handle-large-latch-5-56mm-223/","retrieved":"2026-10-05","via":"harvest"},"note":"\"approximately\" is BCM's word: the ± is taken as half its second digit, not its third."},{"id":"photo","value":1.11,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-mk2-charging-handle 02410675303b (BCM's gallery: the large two-latch handle from above, on white, 1280 x 854)","scaleRef":"the shaft's width column by column (shaft_width)","method":"half of what the traced plan is across its two latches' tips (2.623) over the shaft's width: 1.111. By the plain ratio at the T (458 px across the latches, the shaft 70.1 px beside them): 1.106","via":"harvest"},"note":"What the reading of BCM's figure rests on: its medium handle's photo, taken the same way (9b26e2f1d7fd: 397 px across, the shaft 70.1 px), gives 0.93 where BCM says \"approximately 0.92\"."}],"adopt":{"from":"bcm","reason":"The maker's figure; its photo agrees within 1% when the figure is read as from the shaft's side face to the latch's tip, and the medium handle's figure and photo agree the same way."},"note":"BCM doesn't say where on the main body it is measured from, nor that it is each side's on this two-latch handle."},"channel_width":{"label":"The key's channel under the shaft: its width","kind":"length","measurements":[{"id":"tdp","value":0.312,"unit":"in","pm":0.005,"stated":".312","source":{"type":"standard","doc":"US Army TDP drawing 8448518 (Handle, Charging), rev G, scale 2/1, PDF page 128, Section A-A"},"note":"With FULL R: its roof is a half round of this width."}]},"channel_depth":{"label":"The key's channel: its depth from the shaft's underside to the top of its round roof","kind":"length","measurements":[{"id":"tdp","value":0.25,"unit":"in","pm":0.005,"stated":".250","source":{"type":"standard","doc":"US Army TDP drawing 8448518 (Handle, Charging), rev G, scale 2/1, PDF page 128, Section A-A"},"note":"Read as from the open face to the roof's top: the shaft is .2985 thick, which leaves .0485 above it, where the side view's hidden line is."}]},"hook_length":{"label":"The front hook: its rear face to its tip","kind":"length","measurements":[{"id":"tdp","value":0.295,"unit":"in","pm":0.005,"stated":".295","source":{"type":"standard","doc":"US Army TDP drawing 8448518 (Handle, Charging), rev G, scale 2/1, PDF page 128, side view"}}]},"hook_drop":{"label":"The front hook: how far it hangs below the shaft's underside","kind":"length","measurements":[{"id":"tdp","value":0.275,"unit":"in","pm":0.005,"stated":".275 -C-","source":{"type":"standard","doc":"US Army TDP drawing 8448518 (Handle, Charging), rev G, scale 2/1, PDF page 128, side view"},"note":"Read as from the shaft's underside to the hook's foot (88 px at 316 px/in: .278); from the shaft's top it would end above the underside."}]},"hook_fillet_r":{"label":"The front hook: the round between its rear face and the shaft's underside","kind":"length","measurements":[{"id":"tdp","value":0.187,"unit":"in","pm":0.005,"stated":".187 R","source":{"type":"standard","doc":"US Army TDP drawing 8448518 (Handle, Charging), rev G, scale 2/1, PDF page 128, side view"}}]},"guide_lug_width":{"label":"Across the two guide lugs near the shaft's front end","kind":"length","measurements":[{"id":"tdp","value":0.488,"unit":"in","pm":0.005,"stated":".488","source":{"type":"standard","doc":"US Army TDP drawing 8448518 (Handle, Charging), rev G, scale 2/1, PDF page 128, end view"}}]},"guide_lug_height":{"label":"The guide lugs' height, from the shaft's underside up","kind":"length","measurements":[{"id":"tdp","value":0.119,"unit":"in","pm":0.002,"stated":".119 ±.002","source":{"type":"standard","doc":"US Army TDP drawing 8448518 (Handle, Charging), rev G, scale 2/1, PDF page 128, end view"},"note":"Read as the lugs' height: in the side view they stand on the underside, 36 px high at 316 px/in (.114)."}]},"top_flat_width":{"label":"The flat along the shaft's top, between its two chamfers","kind":"length","measurements":[{"id":"photo","value":0.14,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/bcm-mk2-charging-handle 68a6620f0132 (Primary Arms: the part from ahead of its right side and above, 2200 x 1467)","scaleRef":"the shaft's own section in the fitted camera (shaft_width, shaft_thickness)","method":"fitted with the camera: the flat's two edges where the shaft's brightness steps, at 0.117 and 0.366 of its width in the photo, station by station; 0.1405. BCM's top photo (02410675303b) has the three bands 23, 25 and 22 px of the shaft's 71: 0.14","via":"harvest"},"note":"The Army's drawing has .15 (8448518, Section A-A)."}]},"top_chamfer_drop":{"label":"The shaft's top chamfers: how far below the top their lower edges are","kind":"length","measurements":[{"id":"photo","value":0.076,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/bcm-mk2-charging-handle 68a6620f0132 (Primary Arms: the part from ahead of its right side and above, 2200 x 1467)","scaleRef":"the shaft's own section in the fitted camera (shaft_width, shaft_thickness)","method":"fitted with the camera: the near chamfer's lower edge at 0.697 of the shaft's width in the photo, the far one's the far silhouette; 0.0758","via":"harvest"},"note":"The Army's drawing has 30 degrees over .125: .072."}]},"t_width":{"label":"The T, side to side: across the two latches' tips","kind":"length","measurements":[{"id":"photo","value":2.623,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-mk2-charging-handle 02410675303b (BCM's gallery: the large two-latch handle from above, on white, 1280 x 854)","scaleRef":"scale from bcm-mk2-charging-handle.shaft_width = 0.4 in, the tube's own width column by column: 71.5 px over columns 50–195, 70.8 px over columns 284–324, 70.3 px over columns 874–894, 70.1 px over columns 988–1000; a line through them (rms 0.14 px) changes -2.0% from column 50 to 1000, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 640)/width, the lens's axis taken to meet the image at column 640; 176.5 px/in there. The axis is the tube's centre line (tilt -0.17°, rms 0.04 px)","method":"height of the traced outline (tools/trace.py); across the two latches' tips (their top faces' edges)","via":"harvest"}},{"id":"bcm","value":2.6,"unit":"in","pm":0.1,"source":{"type":"derived","expr":"{.shaft_width} + 2 * {.latch_reach}","via":"harvest"},"note":"BCM's \"approximately 1.10\" for a latch, taken from the shaft's side face, each side of the standard's shaft."}],"adopt":{"from":"photo","reason":"BCM's own photo at the scale its shaft's width gives; BCM's figure, read as from the shaft's side, makes 2.60: within 1%, which is what the reading of that figure rests on (latch_reach)."},"note":"BCM's figure for a latch, taken from the shaft's side, makes it shaft_width + 2 x latch_reach = 2.60."},"t_depth":{"label":"The T, front to back: its rear grip's rear edge behind the shoulder","kind":"length","measurements":[{"id":"photo","value":1.014,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-mk2-charging-handle 02410675303b (BCM's gallery: the large two-latch handle from above, on white, 1280 x 854)","scaleRef":"scale from bcm-mk2-charging-handle.shaft_width = 0.4 in, the tube's own width column by column: 71.5 px over columns 50–195, 70.8 px over columns 284–324, 70.3 px over columns 874–894, 70.1 px over columns 988–1000; a line through them (rms 0.14 px) changes -2.0% from column 50 to 1000, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 640)/width, the lens's axis taken to meet the image at column 640; 176.5 px/in there. The axis is the tube's centre line (tilt -0.17°, rms 0.04 px)","method":"−x_min of the traced outline (tools/trace.py); the rear grip's rear edge behind the shoulder","via":"harvest"}}]},"latch_thickness":{"label":"A latch's thickness: its top face (at its hub, where the pin is) above its underside","kind":"length","measurements":[{"id":"photo","value":0.278,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bcm-mk2-charging-handle 68a6620f0132 (Primary Arms: the part from ahead of its right side and above, 2200 x 1467)","scaleRef":"the fitted camera; the pins' places from BCM's top photo (02410675303b)","method":"the two pins' heights, 0.135 and 0.123 above the channel's axis (0.7 px each off their plan places), over the shaft's underside; the left latch's rear top edge on the skyline reads 0.116","via":"harvest"}}],"note":"The latches' feet read 0.14 below the channel's axis, the shaft's underside 0.149: taken as flush with it, as the standard's T is."},"latch_front_height":{"label":"A latch's ribbed front face: its height","kind":"length","measurements":[{"id":"photo","value":0.23,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-mk2-charging-handle 68a6620f0132 (Primary Arms: the part from ahead of its right side and above, 2200 x 1467)","scaleRef":"the fitted camera; the latch's front edge in plan from BCM's top photo (02410675303b)","method":"nine grooves on the right latch's front face, each one's two ends put on the plan's front edge: 0.214 to 0.254 high, their feet 0.128 to 0.150 below the channel's axis, their tops 0.065 to 0.110 above it (the top face's front edge is rounded off)","via":"harvest"}}]},"t_height":{"label":"The T's height: the rear grip's top above the shaft's underside","kind":"length","measurements":[{"id":"photo","value":0.33,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-charging-handle 68a6620f0132 (Primary Arms: the part from ahead of its right side and above, 2200 x 1467)","scaleRef":"the fitted camera; the T's rear outline and the rear grip's lobes in plan from BCM's top photo (02410675303b)","method":"the first dark pixel down each of twelve columns over the rear grip, put on the plan's rear outline: 0.160 to 0.205 above the channel's axis (0.18 at the middle), a lower bound for anything ahead of that edge; and the lobes' plan drawn over the photo at 0.16, 0.20, 0.24 and 0.28: the far lobe's top lies on 0.16 to 0.17, the near one's on 0.18 to 0.20, and at 0.24 both stand clear above the photo's. Taken as 0.18 above the axis, over the shaft's underside","via":"harvest"}}],"note":"The rear grip's lobes and the rim between them read alike within 0.03. A first reading of 0.49 (a lobe's dark front face taken as upright on the plan's line) was wrong: drawn over the photo at that height the lobes stand clear above it."},"rib_pitch":{"label":"The grooves on a latch's front face: their pitch","kind":"length","measurements":[{"id":"photo","value":0.06,"unit":"in","pm":0.003,"source":{"type":"photo","photo":"references/bcm-mk2-charging-handle 68a6620f0132 (Primary Arms: the part from ahead of its right side and above, 2200 x 1467)","scaleRef":"the fitted camera; the latch's front edge in plan from BCM's top photo (02410675303b)","method":"nine grooves on the right latch from 0.628 to 1.109 off the centre line: 0.060 apart. The plan's outline has the same teeth along that edge, 0.058 to 0.063 apart","via":"harvest"}}]},"rib_count":{"label":"The grooves on a latch's front face: how many","kind":"count","measurements":[{"id":"photo","value":10,"unit":"count","source":{"type":"photo","photo":"references/bcm-mk2-charging-handle 02410675303b (BCM's gallery: the large two-latch handle from above, on white, 1280 x 854)","scaleRef":"none: a count","method":"the teeth along the right latch's front edge in the traced outline, 0.58 to 1.08 off the centre line; Primary Arms' oblique photo (68a6620f0132) shows nine of them","via":"harvest"}}],"note":"Counted where the two photos show them; more may lie under the rear grip's lobe."},"rib_depth":{"label":"The grooves on a latch's front face: their depth","kind":"length","measurements":[{"id":"photo","value":0.02,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-mk2-charging-handle 02410675303b (BCM's gallery: the large two-latch handle from above, on white, 1280 x 854)","scaleRef":"the shaft's width column by column (shaft_width)","method":"how far the traced outline's teeth step in and out along the right latch's front edge: 0.018 to 0.023","via":"harvest"}}]},"rib_first_z":{"label":"The grooves on a latch's front face: the first one's distance off the shaft's centre line","kind":"length","measurements":[{"id":"photo","value":0.58,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-mk2-charging-handle 02410675303b (BCM's gallery: the large two-latch handle from above, on white, 1280 x 854)","scaleRef":"the shaft's width column by column (shaft_width)","method":"the first tooth of the traced outline along the right latch's front edge, 0.576 to 0.588 off the centre line","via":"harvest"}}]},"top_chamfer_from_shoulder":{"label":"The shaft's top chamfers: where they have run out, ahead of the shoulder","kind":"length","measurements":[{"id":"tdp","value":0.235,"unit":"in","pm":0.015,"stated":".235 ±.015","source":{"type":"standard","doc":"US Army TDP drawing 8448518 (Handle, Charging), rev G, scale 2/1, PDF page 128, plan view"},"note":"With \".25 R TRUE 2 PLACES\": from the T's front face to where the chamfers' round run-out ends. BCM's top photo has its flat widen to the shaft's full width 0.23 ahead of the shoulder."}]},"pin_behind_shoulder":{"label":"The latches' two pins: how far behind the shoulder","kind":"length","measurements":[{"id":"photo","value":0.368,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-mk2-charging-handle 02410675303b (BCM's gallery: the large two-latch handle from above, on white, 1280 x 854)","scaleRef":"the shaft's width column by column (shaft_width)","method":"the two bright pin ends' centres, at pixels (1144.3, 381.0) and (1144.0, 470.7), through the plan's own map: 0.369 and 0.367 behind the shoulder's column","via":"harvest"}}]},"pin_off_centre":{"label":"The latches' two pins: how far each is off the shaft's centre line","kind":"length","measurements":[{"id":"photo","value":0.257,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/bcm-mk2-charging-handle 02410675303b (BCM's gallery: the large two-latch handle from above, on white, 1280 x 854)","scaleRef":"the shaft's width column by column (shaft_width)","method":"the two bright pin ends' centres through the plan's own map: 0.256 to the right and 0.258 to the left","via":"harvest"}}]},"pin_d":{"label":"The latches' pins: their ends' diameter","kind":"length","measurements":[{"id":"photo","value":0.092,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-mk2-charging-handle 02410675303b (BCM's gallery: the large two-latch handle from above, on white, 1280 x 854)","scaleRef":"the shaft's width column by column (shaft_width): 174.6 px/in at the pins","method":"each bright pin end is 16 px across (15 to 16 down); the glare may widen it","via":"harvest"}}],"note":"Roll pins: Primary Arms' photos show their ends as rings."},"hub_r":{"label":"The latches' hubs: the radius of their outlines about the pins","kind":"length","measurements":[{"id":"photo","value":0.25,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-mk2-charging-handle 02410675303b (BCM's gallery: the large two-latch handle from above, on white, 1280 x 854)","scaleRef":"the shaft's width column by column (shaft_width): 174.6 px/in at the pins","method":"the right hub's round outline spans rows 337 to 425 and columns 1100 to 1188 (88 px across); the two hubs' outlines meet on the shaft's centre line, where the pins' distance off it (pin_off_centre) would have them","via":"harvest"}}]}}},{"subject":"bcm-mk2-lower-receiver","title":"BCM MK2 AR-15 Lower Receiver (the receiver of the complete lower LRG-RMS-NO-STOCK, with its parts kit and trigger guard)","dimensions":{"weight":{"label":"Weight (the receiver with its parts kit and trigger guard installed; no trigger, grip or buffer system)","kind":"mass","measurements":[{"id":"worked-out","value":11.13,"unit":"oz","pm":0.8,"source":{"type":"derived","expr":"{.receiver_weight} + {.guard_weight} + {rise-lpk.weight}","via":"harvest"},"note":"The forging by its metal, the guard by its polymer, and the parts kit installed in it (its pins, selector, bolt catch, magazine catch, springs and detents: no trigger group, no grip, no guard) as the controls the app draws for it are weighed: Rise's kit without its fire-control group or trigger guard, 2.5 oz by its seller (rise-lpk.weight). BCM's own kit isn't weighed by any page (its enhanced kit's product data: \"weight\":null)."}],"note":"No page weighs this part: Primary Arms' three pages give no weight, BCM sells no stripped lower, Blackstone's page data says \"weight\":null. Worked out: the forging's metal, the guard's polymer and the small parts as the catalog's controls-only kit is weighed (see each)."},"receiver_weight":{"label":"The forging alone, by its metal","kind":"mass","measurements":[{"id":"model","value":8.53,"unit":"oz","pm":0.5,"source":{"type":"derived","basis":"The receiver model's volume, 5.224 cubic inches (pipeline/blender/bcm_mk2_lower_receiver.py's manifest, app/public/models/bcm-mk2-lower-receiver.receiver.json volume_in3), times std.density.aluminium_7075 (1.632 oz to the cubic inch: \"Forged 7075-T6 aluminum construction\", Primary Arms): 8.53 oz. The ± is what the model draws without a reading: the body's width the drawing's, the roll's crest assumed, the well's walls as thick as the walls' width leaves them, the inside at the drawing's nominal sizes (about 0.3 cubic inches either way).","via":"harvest"},"note":"Worked out, not weighed: no page gives this forging's weight. The catalog's other forged mil-spec lowers come to 7.9 to 8.4 oz the same way and by their makers."}]},"guard_weight":{"label":"The trigger guard alone, by its polymer","kind":"mass","measurements":[{"id":"model","value":0.104,"unit":"oz","pm":0.04,"source":{"type":"derived","basis":"The guard model's volume, 0.158 cubic inches (app/public/models/bcm-mk2-lower-receiver.guard.json volume_in3), times std.density.polymer (0.659 oz to the cubic inch, a polyamide's: BCM, \"Made of impact resistant polymer\", names no grade): 0.104 oz. The ± is a glass fill's and the ends' assumed reach between the ears; its roll pin and set screw aren't in it.","via":"harvest"},"note":"Worked out, not weighed: BCM's guard page has \"weight\":null in its own product data."}]},"trigger_pin_diameter":{"label":"Trigger and hammer pin diameter","kind":"length","measurements":[{"id":"primary-arms","value":0.154,"unit":"in","pm":0.0005,"stated":"Trigger Pin Diameter MIL-SPEC .154","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Bravo Company Manufacturing MK2 AR-15 Lower Receiver - Complete Lower - No Stock (LRG-RMS-NO-STOCK), Specifications","url":"https://www.primaryarms.com/bcm-mk2-ar-15-complete-lower-receiver-no-stock","retrieved":"2026-10-28","via":"harvest"},"note":"The same row on the blem's page and the Mod 0 stock lower's. The drawing's holes are .1555 to .1580 for these pins (std.ar15.fcg_pin_hole_d)."}]},"width":{"label":"Receiver maximum width (Z)","kind":"length","measurements":[{"id":"std","value":0.88,"unit":"in","pm":0.008,"source":{"type":"derived","expr":"{std.ar15.lower_body_width}","via":"harvest"},"note":"The body's width is the Army drawing's (Section C-C). A mil-spec pattern: Primary Arms of this lower, \"ready for any Mil-Spec upper\" (the Mod 0 stock lower's page) and \"Trigger Pin Diameter MIL-SPEC .154\"; BCM, of its parts kit, \"all MIL SPEC lower receivers built per the USGI TDP\". The drawing's figure (8448608)."}],"note":"No page states a width and no photo on file looks along the receiver. The body is the drawing's; the well's walls, the roll along the well's right top and the tower's ring stand wider."},"buffer_axis_above_pin":{"label":"Receiver extension (bore) axis above the takedown pin centre","kind":"length","measurements":[{"id":"std","value":0.8775,"unit":"in","pm":0.0015,"source":{"type":"derived","expr":"{std.ar15.bore_axis_y}","via":"harvest"},"note":"A mil-spec pattern: Primary Arms of this lower, \"ready for any Mil-Spec upper\" (the Mod 0 stock lower's page) and \"Trigger Pin Diameter MIL-SPEC .154\"; BCM, of its parts kit, \"all MIL SPEC lower receivers built per the USGI TDP\". The drawing's figure (8448608)."}]},"magazine_seat_x":{"label":"Magazine seat, X (a seated magazine's frame origin ahead of the takedown pin)","kind":"length","measurements":[{"id":"milspec","value":3.4915,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{bad-workhorse-lower.magazine_seat_x}","via":"user"},"note":"Where a magazine seats in a mil-spec well, from the Army drawing's well and catch slot and the user's own magazine, recorded on the Workhorse (as the catalog's other mil-spec lowers take it). No photo of a magazine seated in this lower is on file; its catch's button is at the drawing's place on the right photo (3.247, -0.566 for 3.291, -0.565)."}]},"magazine_seat_y":{"label":"Magazine seat, Y (the feed-lip top of a seated magazine)","kind":"length","measurements":[{"id":"milspec","value":1.003,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{bad-workhorse-lower.magazine_seat_y}","via":"user"},"note":"As magazine_seat_x: the standard well's and the catch's."}]},"grip_seat_y":{"label":"Grip seat, Y (the underside a grip's flat top bears on, at the takedown pin's X)","kind":"length","measurements":[{"id":"tdp","value":-1.0695,"unit":"in","pm":0.0115,"source":{"type":"derived","expr":"{std.ar15.deck_y} - {std.ar15.grip_seat_below_deck}","via":"harvest"},"note":"The flat the lug hangs from, 1.318 below the deck: the drawing's. A mil-spec pattern: Primary Arms of this lower, \"ready for any Mil-Spec upper\" (the Mod 0 stock lower's page) and \"Trigger Pin Diameter MIL-SPEC .154\"; BCM, of its parts kit, \"all MIL SPEC lower receivers built per the USGI TDP\". The drawing's figure (8448608)."},{"id":"right","value":-1.11,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 842fbe8fe0ba (the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467)","scaleRef":"a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face","method":"picked at px (1440, 634) on a gridded crop (scratch/crop.py), carried through that frame: the body's lower edge over the trigger's opening, where the opening's rear turns up","via":"harvest"},"note":"The grip hides the seat itself; the edge over the opening is the same plane on the drawing, and reads 0.04 below it here (the far wall's edge, from a lens a little above)."}],"adopt":{"from":"tdp","reason":"The drawing's; the photo's edge over the opening is 0.04 lower, within its ± and in the sense a lens above the part gives."}},"trigger_pin_x":{"label":"Trigger pin hole centre, X","kind":"length","measurements":[{"id":"tdp","value":1.928,"unit":"in","pm":0.004,"source":{"type":"derived","expr":"{std.ar15.trigger_pin_x}","via":"harvest"},"note":"A mil-spec pattern: Primary Arms of this lower, \"ready for any Mil-Spec upper\" (the Mod 0 stock lower's page) and \"Trigger Pin Diameter MIL-SPEC .154\"; BCM, of its parts kit, \"all MIL SPEC lower receivers built per the USGI TDP\". The drawing's figure (8448608)."},{"id":"right","value":1.927,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 842fbe8fe0ba (the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467)","scaleRef":"a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face","method":"picked at px (1474, 578) on a gridded crop (scratch/crop.py), carried through that frame: the hole's end (a pin's end, the selector's end, the guard's roll pin, the guard's front hole) as its ring's centre; one of the frame's own points, so a check of the frame's fit, not of the drawing","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's: the hole is one of the points the photo's frame was fitted to, and sits within its ± of it."}},"trigger_pin_y":{"label":"Trigger pin hole centre, Y","kind":"length","measurements":[{"id":"tdp","value":-0.689,"unit":"in","pm":0.004,"source":{"type":"derived","expr":"{std.ar15.trigger_pin_y}","via":"harvest"},"note":"A mil-spec pattern: Primary Arms of this lower, \"ready for any Mil-Spec upper\" (the Mod 0 stock lower's page) and \"Trigger Pin Diameter MIL-SPEC .154\"; BCM, of its parts kit, \"all MIL SPEC lower receivers built per the USGI TDP\". The drawing's figure (8448608)."},{"id":"right","value":-0.691,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 842fbe8fe0ba (the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467)","scaleRef":"a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face","method":"picked at px (1474, 578) on a gridded crop (scratch/crop.py), carried through that frame: the hole's end (a pin's end, the selector's end, the guard's roll pin, the guard's front hole) as its ring's centre; one of the frame's own points, so a check of the frame's fit, not of the drawing","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's: the hole is one of the points the photo's frame was fitted to, and sits within its ± of it."}},"hammer_pin_x":{"label":"Hammer pin hole centre, X","kind":"length","measurements":[{"id":"tdp","value":2.771,"unit":"in","pm":0.004,"source":{"type":"derived","expr":"{std.ar15.hammer_pin_x}","via":"harvest"},"note":"A mil-spec pattern: Primary Arms of this lower, \"ready for any Mil-Spec upper\" (the Mod 0 stock lower's page) and \"Trigger Pin Diameter MIL-SPEC .154\"; BCM, of its parts kit, \"all MIL SPEC lower receivers built per the USGI TDP\". The drawing's figure (8448608)."},{"id":"right","value":2.754,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 842fbe8fe0ba (the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467)","scaleRef":"a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face","method":"picked at px (1585.5, 538.5) on a gridded crop (scratch/crop.py), carried through that frame: the hole's end (a pin's end, the selector's end, the guard's roll pin, the guard's front hole) as its ring's centre; one of the frame's own points, so a check of the frame's fit, not of the drawing","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's: the hole is one of the points the photo's frame was fitted to, and sits within its ± of it."}},"hammer_pin_y":{"label":"Hammer pin hole centre, Y","kind":"length","measurements":[{"id":"tdp","value":-0.375,"unit":"in","pm":0.004,"source":{"type":"derived","expr":"{std.ar15.hammer_pin_y}","via":"harvest"},"note":"A mil-spec pattern: Primary Arms of this lower, \"ready for any Mil-Spec upper\" (the Mod 0 stock lower's page) and \"Trigger Pin Diameter MIL-SPEC .154\"; BCM, of its parts kit, \"all MIL SPEC lower receivers built per the USGI TDP\". The drawing's figure (8448608)."},{"id":"right","value":-0.384,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 842fbe8fe0ba (the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467)","scaleRef":"a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face","method":"picked at px (1585.5, 538.5) on a gridded crop (scratch/crop.py), carried through that frame: the hole's end (a pin's end, the selector's end, the guard's roll pin, the guard's front hole) as its ring's centre; one of the frame's own points, so a check of the frame's fit, not of the drawing","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's: the hole is one of the points the photo's frame was fitted to, and sits within its ± of it."}},"selector_x":{"label":"Selector hole centre, X","kind":"length","measurements":[{"id":"tdp","value":0.803,"unit":"in","pm":0.004,"source":{"type":"derived","expr":"{std.ar15.selector_x}","via":"harvest"},"note":"A mil-spec pattern: Primary Arms of this lower, \"ready for any Mil-Spec upper\" (the Mod 0 stock lower's page) and \"Trigger Pin Diameter MIL-SPEC .154\"; BCM, of its parts kit, \"all MIL SPEC lower receivers built per the USGI TDP\". The drawing's figure (8448608)."},{"id":"right","value":0.813,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 842fbe8fe0ba (the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467)","scaleRef":"a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face","method":"picked at px (1325, 547) on a gridded crop (scratch/crop.py), carried through that frame: the hole's end (a pin's end, the selector's end, the guard's roll pin, the guard's front hole) as its ring's centre; one of the frame's own points, so a check of the frame's fit, not of the drawing","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's: the hole is one of the points the photo's frame was fitted to, and sits within its ± of it."}},"selector_y":{"label":"Selector hole centre, Y","kind":"length","measurements":[{"id":"tdp","value":-0.466,"unit":"in","pm":0.004,"source":{"type":"derived","expr":"{std.ar15.selector_y}","via":"harvest"},"note":"A mil-spec pattern: Primary Arms of this lower, \"ready for any Mil-Spec upper\" (the Mod 0 stock lower's page) and \"Trigger Pin Diameter MIL-SPEC .154\"; BCM, of its parts kit, \"all MIL SPEC lower receivers built per the USGI TDP\". The drawing's figure (8448608)."},{"id":"right","value":-0.476,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 842fbe8fe0ba (the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467)","scaleRef":"a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face","method":"picked at px (1325, 547) on a gridded crop (scratch/crop.py), carried through that frame: the hole's end (a pin's end, the selector's end, the guard's roll pin, the guard's front hole) as its ring's centre; one of the frame's own points, so a check of the frame's fit, not of the drawing","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's: the hole is one of the points the photo's frame was fitted to, and sits within its ± of it."}},"trigger_guard_rear_x":{"label":"Trigger guard rear ear hole, X","kind":"length","measurements":[{"id":"tdp","value":1.4985,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.ar15.trigger_guard_rear_x}","via":"harvest"},"note":"A mil-spec pattern: Primary Arms of this lower, \"ready for any Mil-Spec upper\" (the Mod 0 stock lower's page) and \"Trigger Pin Diameter MIL-SPEC .154\"; BCM, of its parts kit, \"all MIL SPEC lower receivers built per the USGI TDP\". The drawing's figure (8448608)."},{"id":"right","value":1.479,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 842fbe8fe0ba (the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467)","scaleRef":"a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face","method":"picked at px (1411, 777) on a gridded crop (scratch/crop.py), carried through that frame: the hole's end (a pin's end, the selector's end, the guard's roll pin, the guard's front hole) as its ring's centre; one of the frame's own points, so a check of the frame's fit, not of the drawing","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's: the hole is one of the points the photo's frame was fitted to, and sits within its ± of it."}},"trigger_guard_rear_y":{"label":"Trigger guard rear ear hole, Y","kind":"length","measurements":[{"id":"tdp","value":-2.18,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.ar15.trigger_guard_rear_y}","via":"harvest"},"note":"A mil-spec pattern: Primary Arms of this lower, \"ready for any Mil-Spec upper\" (the Mod 0 stock lower's page) and \"Trigger Pin Diameter MIL-SPEC .154\"; BCM, of its parts kit, \"all MIL SPEC lower receivers built per the USGI TDP\". The drawing's figure (8448608)."},{"id":"right","value":-2.181,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 842fbe8fe0ba (the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467)","scaleRef":"a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face","method":"picked at px (1411, 777) on a gridded crop (scratch/crop.py), carried through that frame: the hole's end (a pin's end, the selector's end, the guard's roll pin, the guard's front hole) as its ring's centre; one of the frame's own points, so a check of the frame's fit, not of the drawing","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's: the hole is one of the points the photo's frame was fitted to, and sits within its ± of it."}},"trigger_guard_front_x":{"label":"Trigger guard front ear hole, X","kind":"length","measurements":[{"id":"tdp","value":3.3425,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.ar15.trigger_guard_front_x}","via":"harvest"},"note":"A mil-spec pattern: Primary Arms of this lower, \"ready for any Mil-Spec upper\" (the Mod 0 stock lower's page) and \"Trigger Pin Diameter MIL-SPEC .154\"; BCM, of its parts kit, \"all MIL SPEC lower receivers built per the USGI TDP\". The drawing's figure (8448608)."},{"id":"right","value":3.298,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 842fbe8fe0ba (the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467)","scaleRef":"a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face","method":"picked at px (1655, 778) on a gridded crop (scratch/crop.py), carried through that frame: the hole's end (a pin's end, the selector's end, the guard's roll pin, the guard's front hole) as its ring's centre; one of the frame's own points, so a check of the frame's fit, not of the drawing","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's: the hole is one of the points the photo's frame was fitted to, and sits within its ± of it."}},"trigger_guard_front_y":{"label":"Trigger guard front ear hole, Y","kind":"length","measurements":[{"id":"tdp","value":-2.18,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.ar15.trigger_guard_rear_y}","via":"harvest"},"note":"A mil-spec pattern: Primary Arms of this lower, \"ready for any Mil-Spec upper\" (the Mod 0 stock lower's page) and \"Trigger Pin Diameter MIL-SPEC .154\"; BCM, of its parts kit, \"all MIL SPEC lower receivers built per the USGI TDP\". The drawing's figure (8448608)."},{"id":"right","value":-2.162,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 842fbe8fe0ba (the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467)","scaleRef":"a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face","method":"picked at px (1655, 778) on a gridded crop (scratch/crop.py), carried through that frame: the hole's end (a pin's end, the selector's end, the guard's roll pin, the guard's front hole) as its ring's centre; one of the frame's own points, so a check of the frame's fit, not of the drawing","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's: the hole is one of the points the photo's frame was fitted to, and sits within its ± of it."}},"rear_behind_pin":{"label":"Rear face (the buffer tower's, where the end plate bears) behind the takedown pin","kind":"length","measurements":[{"id":"std","value":1.125,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"-{std.ar15.receiver_rear_x}","via":"harvest"},"note":"A mil-spec pattern: Primary Arms of this lower, \"ready for any Mil-Spec upper\" (the Mod 0 stock lower's page) and \"Trigger Pin Diameter MIL-SPEC .154\"; BCM, of its parts kit, \"all MIL SPEC lower receivers built per the USGI TDP\". The drawing's figure (8448608). The right photo has BCM's QD end plate against it, its front face at 1.044 behind the pin: the plate's near face, standing out of the photo's frame plane, which the face's own figure doesn't rest on."}]},"tower_top_above_pin":{"label":"Top of the buffer-tower ring above the pin line","kind":"length","measurements":[{"id":"std","value":1.5735,"unit":"in","pm":0.0065,"source":{"type":"derived","expr":"{std.ar15.buffer_tower_top_y}","via":"harvest"},"note":"A mil-spec pattern: the ring's top is the drawing's (1.325 above the deck)."},{"id":"right","value":1.511,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 842fbe8fe0ba (the no-stock complete lower's right side on white: Primary Arms' LRG-RMS-NO-STOCK_01 (2200 x 1467))","scaleRef":"frame from the reviewed holes takedown, pivot, selector, trigger, hammer, guard_rear, guard_front (134.1 px/in, rms 0.030 in over 7 points)","method":"y_max of the traced outline (tools/trace.py)","via":"harvest"},"note":"The tower ring's top as its silhouette: the drawing's is 1.5735 (std.ar15.buffer_tower_top_y)."}],"adopt":{"from":"std","reason":"The drawing's: the photo's silhouette there is cut by the end plate taken out of the mask, and reads low by what a round ring falls in 0.2 in ahead of its crest."},"note":"The right photo's silhouette over the ring is 0.06 under the drawing's top: the ring is round and stands behind the end plate and castle nut there, which were taken out of the mask at the ring's rear (x -0.96), so the outline's highest point is the ring's shoulder ahead of its crest, not its top."},"deck_above_pin":{"label":"Deck (the receiver's top edge between the tower and the pivot lug) above the pin line","kind":"length","measurements":[{"id":"right","value":0.246,"unit":"in","pm":0.022,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 842fbe8fe0ba (the no-stock complete lower's right side on white: Primary Arms' LRG-RMS-NO-STOCK_01 (2200 x 1467))","scaleRef":"frame from the reviewed holes takedown, pivot, selector, trigger, hammer, guard_rear, guard_front (134.1 px/in, rms 0.030 in over 7 points)","method":"top (tooth tops: the edge's max over 0.05 in windows) along x [0.6, 5.8] of the traced outline (tools/trace.py)","via":"harvest"},"note":"The top edge between the tower and the pivot lug: the drawing's deck is 0.2485 (std.ar15.deck_y)."}]},"tower_front_x":{"label":"Front edge of the walls' sweep up to the tower ring, above the deck, X","kind":"length","measurements":[{"id":"right","value":-0.439,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 842fbe8fe0ba (the no-stock complete lower's right side on white: Primary Arms' LRG-RMS-NO-STOCK_01 (2200 x 1467))","scaleRef":"frame from the reviewed holes takedown, pivot, selector, trigger, hammer, guard_rear, guard_front (134.1 px/in, rms 0.030 in over 7 points)","method":"x_max in x [-1.5, 3.0] in y [0.5, 1.4] of the traced outline (tools/trace.py)","via":"harvest"},"note":"Front edge of the walls' sweep up to the ring, above the deck."}]},"front_ahead_of_pin":{"label":"Front of the pivot-pin lug, X","kind":"length","measurements":[{"id":"left","value":6.568,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 810d3932dc10 (the same lower, LEFT side, square on white: Primary Arms LRG-RMS-NO-STOCK_03, 2200 x 1467)","scaleRef":"a frame fitted by least squares to the takedown and pivot pins' flush ends and the trigger and hammer pins' ends (std.ar15.*): 131.1 px/in, turned 1.86 degrees; every one within 0.008 in","method":"picked at px (95, 458) on a gridded crop (scratch/crop.py), carried through that frame: the lug's rounded front on the left side, where the pivot pin's flush end is its centre","via":"harvest"}},{"id":"right","value":6.626,"unit":"in","pm":0.035,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 842fbe8fe0ba (the no-stock complete lower's right side on white: Primary Arms' LRG-RMS-NO-STOCK_01 (2200 x 1467))","scaleRef":"frame from the reviewed holes takedown, pivot, selector, trigger, hammer, guard_rear, guard_front (134.1 px/in, rms 0.030 in over 7 points)","method":"x_max of the traced outline (tools/trace.py)","via":"harvest"},"note":"The right side's front is the pivot pin's domed head standing out of the right ear (0.43 in across on the photo), 0.06 ahead of the lug it covers."}],"adopt":{"from":"left","reason":"The lug itself: on the left side the pin's end is flush and the lug's round front is the silhouette; on the right the pin's head stands over it and reaches further."}},"magwell_front_x":{"label":"Front face of the magazine well, X","kind":"length","measurements":[{"id":"right","value":6.091,"unit":"in","pm":0.033,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 842fbe8fe0ba (the no-stock complete lower's right side on white: Primary Arms' LRG-RMS-NO-STOCK_01 (2200 x 1467))","scaleRef":"frame from the reviewed holes takedown, pivot, selector, trigger, hammer, guard_rear, guard_front (134.1 px/in, rms 0.030 in over 7 points)","method":"x_max in x [3.0, 7.0] in y [-1.5, -0.6] of the traced outline (tools/trace.py)","via":"harvest"},"note":"Front face of the magazine well (the near wall's)."}]},"bottom_below_pin":{"label":"Lowest point of the receiver below the pin line (the guard apart)","kind":"length","measurements":[{"id":"right","value":2.298,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 842fbe8fe0ba (the no-stock complete lower's right side on white: Primary Arms' LRG-RMS-NO-STOCK_01 (2200 x 1467))","scaleRef":"frame from the reviewed holes takedown, pivot, selector, trigger, hammer, guard_rear, guard_front (134.1 px/in, rms 0.030 in over 7 points)","method":"−y_min of the traced outline (tools/trace.py)","via":"harvest"},"note":"Lowest point of the receiver as traced (the guard and the rear ears are taken out): the front ears' foot at the well's rear."}]},"rear_ear_bottom_y":{"label":"The trigger guard's rear ears, their foot, Y","kind":"length","measurements":[{"id":"right","value":-2.333,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 842fbe8fe0ba (the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467)","scaleRef":"a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face","method":"picked at px (1385, 797) on a gridded crop (scratch/crop.py), carried through that frame: the ears' lower edge between the grip's front and the guard's rear end, where the ears show below the guard","via":"harvest"}}]},"front_ear_bottom_y":{"label":"The trigger guard's front ears, their foot at the well's rear, Y","kind":"length","measurements":[{"id":"right","value":-2.288,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 842fbe8fe0ba (the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467)","scaleRef":"a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face","method":"picked at px (1665, 795) on a gridded crop (scratch/crop.py), carried through that frame: the front ears' lower edge ahead of the guard's front hole","via":"harvest"}}]},"window_rear_x":{"label":"The trigger's opening between the ears, its rear at the seat's level, X","kind":"length","measurements":[{"id":"right","value":1.68,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 842fbe8fe0ba (the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467)","scaleRef":"a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face","method":"picked at px (1440, 634) on a gridded crop (scratch/crop.py), carried through that frame: where the rear ears' front edge meets the body's lower edge over the opening","via":"harvest"}}]},"window_front_x":{"label":"The trigger's opening between the ears, its front at the seat's level, X","kind":"length","measurements":[{"id":"right","value":2.947,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 842fbe8fe0ba (the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467)","scaleRef":"a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face","method":"picked at px (1610, 635) on a gridded crop (scratch/crop.py), carried through that frame: where the front ears' rear edge meets the body's lower edge over the opening","via":"harvest"}}]},"magwell_wall_rear_x":{"label":"Magazine well's outside walls, rear edge, X (right side)","kind":"length","measurements":[{"id":"right","value":3.588,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 842fbe8fe0ba (the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467)","scaleRef":"a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face","method":"picked at px (1695, 700) on a gridded crop (scratch/crop.py), carried through that frame: the upright edge where the well's wall begins, ahead of the fence and the front ears","via":"harvest"}}]},"magwell_wall_rear_x_left":{"label":"Magazine well's outside walls, rear edge of their lower part, X (left side)","kind":"length","measurements":[{"id":"left","value":3.435,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 810d3932dc10 (the same lower, LEFT side, square on white: Primary Arms LRG-RMS-NO-STOCK_03, 2200 x 1467)","scaleRef":"a frame fitted by least squares to the takedown and pivot pins' flush ends and the trigger and hammer pins' ends (std.ar15.*): 131.1 px/in, turned 1.86 degrees; every one within 0.008 in","method":"picked at px (500, 640) on a gridded crop (scratch/crop.py), carried through that frame: the lower end of the left wall's S-curve, at the front ears","via":"harvest"}}]},"magwell_wall_upper_rear_x_left":{"label":"Magazine well's left wall, its upper part's rear edge, X","kind":"length","measurements":[{"id":"left","value":3.03,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 810d3932dc10 (the same lower, LEFT side, square on white: Primary Arms LRG-RMS-NO-STOCK_03, 2200 x 1467)","scaleRef":"a frame fitted by least squares to the takedown and pivot pins' flush ends and the trigger and hammer pins' ends (std.ar15.*): 131.1 px/in, turned 1.86 degrees; every one within 0.008 in","method":"picked at px (555, 560) on a gridded crop (scratch/crop.py), carried through that frame: the left wall's upright rear edge behind the bolt catch's bosses, from the deck down","via":"harvest"}}]},"magwell_wall_curve_top_y_left":{"label":"Magazine well's left wall, where its rear edge begins to curve forward, Y","kind":"length","measurements":[{"id":"left","value":-0.922,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 810d3932dc10 (the same lower, LEFT side, square on white: Primary Arms LRG-RMS-NO-STOCK_03, 2200 x 1467)","scaleRef":"a frame fitted by least squares to the takedown and pivot pins' flush ends and the trigger and hammer pins' ends (std.ar15.*): 131.1 px/in, turned 1.86 degrees; every one within 0.008 in","method":"picked at px (555, 590) on a gridded crop (scratch/crop.py), carried through that frame: the top of the S-curve","via":"harvest"}}]},"magwell_wall_curve_bottom_y_left":{"label":"Magazine well's left wall, where its rear edge's curve ends, Y","kind":"length","measurements":[{"id":"left","value":-1.317,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 810d3932dc10 (the same lower, LEFT side, square on white: Primary Arms LRG-RMS-NO-STOCK_03, 2200 x 1467)","scaleRef":"a frame fitted by least squares to the takedown and pivot pins' flush ends and the trigger and hammer pins' ends (std.ar15.*): 131.1 px/in, turned 1.86 degrees; every one within 0.008 in","method":"picked at px (500, 640) on a gridded crop (scratch/crop.py), carried through that frame: the foot of the S-curve","via":"harvest"}}]},"bolt_catch_boss_rear_x":{"label":"Bolt catch bosses, the rear one's rear edge, X","kind":"length","measurements":[{"id":"left","value":3.091,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 810d3932dc10 (the same lower, LEFT side, square on white: Primary Arms LRG-RMS-NO-STOCK_03, 2200 x 1467)","scaleRef":"a frame fitted by least squares to the takedown and pivot pins' flush ends and the trigger and hammer pins' ends (std.ar15.*): 131.1 px/in, turned 1.86 degrees; every one within 0.008 in","method":"picked at px (550, 488) on a gridded crop (scratch/crop.py), carried through that frame: the rear boss's rear edge on the left face","via":"harvest"}}]},"bolt_catch_boss_front_x":{"label":"Bolt catch bosses, the front one's front edge, X","kind":"length","measurements":[{"id":"left","value":3.617,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 810d3932dc10 (the same lower, LEFT side, square on white: Primary Arms LRG-RMS-NO-STOCK_03, 2200 x 1467)","scaleRef":"a frame fitted by least squares to the takedown and pivot pins' flush ends and the trigger and hammer pins' ends (std.ar15.*): 131.1 px/in, turned 1.86 degrees; every one within 0.008 in","method":"picked at px (481, 488) on a gridded crop (scratch/crop.py), carried through that frame: the front boss's front edge on the left face","via":"harvest"}}]},"bolt_catch_boss_bottom_y":{"label":"Bolt catch bosses, their lower ends, Y","kind":"length","measurements":[{"id":"left","value":-0.154,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 810d3932dc10 (the same lower, LEFT side, square on white: Primary Arms LRG-RMS-NO-STOCK_03, 2200 x 1467)","scaleRef":"a frame fitted by least squares to the takedown and pivot pins' flush ends and the trigger and hammer pins' ends (std.ar15.*): 131.1 px/in, turned 1.86 degrees; every one within 0.008 in","method":"picked at px (481 to 550, 488) on a gridded crop (scratch/crop.py), carried through that frame: the bosses' lower ends (each a rounded end)","via":"harvest"}}]},"bolt_catch_gap_rear_x":{"label":"Bolt catch bosses: the gap between them, rear edge, X","kind":"length","measurements":[{"id":"tdp","value":3.203,"unit":"in","pm":0.007,"source":{"type":"derived","expr":"{std.ar15.bolt_catch_slot_front_x} - {std.ar15.bolt_catch_slot_width}","via":"harvest"},"note":"The gap is the drawing's slot for the catch. The left photo's gap is 0.168 wide (the drawing's .172) from 3.259 to 3.427: 0.05 ahead of the drawing's, inside the frame's miss there."},{"id":"left","value":3.259,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 810d3932dc10 (the same lower, LEFT side, square on white: Primary Arms LRG-RMS-NO-STOCK_03, 2200 x 1467)","scaleRef":"a frame fitted by least squares to the takedown and pivot pins' flush ends and the trigger and hammer pins' ends (std.ar15.*): 131.1 px/in, turned 1.86 degrees; every one within 0.008 in","method":"picked at px (528, 488) on a gridded crop (scratch/crop.py), carried through that frame: the rear boss's front edge","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's slot; the photo's gap has its width and sits 0.056 ahead of it."}},"bolt_catch_gap_front_x":{"label":"Bolt catch bosses: the gap's front edge, X","kind":"length","measurements":[{"id":"tdp","value":3.375,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.ar15.bolt_catch_slot_front_x}","via":"harvest"},"note":"The drawing's slot for the catch."},{"id":"left","value":3.427,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 810d3932dc10 (the same lower, LEFT side, square on white: Primary Arms LRG-RMS-NO-STOCK_03, 2200 x 1467)","scaleRef":"a frame fitted by least squares to the takedown and pivot pins' flush ends and the trigger and hammer pins' ends (std.ar15.*): 131.1 px/in, turned 1.86 degrees; every one within 0.008 in","method":"picked at px (506, 488) on a gridded crop (scratch/crop.py), carried through that frame: the front boss's rear edge","via":"harvest"}}],"adopt":{"from":"tdp","reason":"As bolt_catch_gap_rear_x."}},"fence_rear_x":{"label":"The magazine catch's fence on the right, rear edge, X","kind":"length","measurements":[{"id":"right","value":2.864,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 842fbe8fe0ba (the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467)","scaleRef":"a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face","method":"picked at px (1600, 560) on a gridded crop (scratch/crop.py), carried through that frame: the raised frame round the button's pocket, its rear edge","via":"harvest"}}]},"fence_front_x":{"label":"The magazine catch's fence, front edge, X","kind":"length","measurements":[{"id":"right","value":3.61,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 842fbe8fe0ba (the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467)","scaleRef":"a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face","method":"picked at px (1700, 560) on a gridded crop (scratch/crop.py), carried through that frame: the frame's front edge","via":"harvest"}}]},"fence_top_y":{"label":"The magazine catch's fence, its top (under the roll), Y","kind":"length","measurements":[{"id":"right","value":-0.202,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 842fbe8fe0ba (the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467)","scaleRef":"a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face","method":"picked at px (1650, 515) on a gridded crop (scratch/crop.py), carried through that frame: where the frame meets the roll's lower edge","via":"harvest"}}]},"fence_bottom_y":{"label":"The magazine catch's fence, its lower edge, Y","kind":"length","measurements":[{"id":"right","value":-1.015,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 842fbe8fe0ba (the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467)","scaleRef":"a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face","method":"picked at px (1650, 624) on a gridded crop (scratch/crop.py), carried through that frame: the frame's lower edge over the trigger's opening","via":"harvest"}}]},"fence_corner_r":{"label":"The magazine catch's fence, its corners, radius","kind":"length","measurements":[{"id":"assumed","value":0.06,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the frame's corners on the right photo are round, about this much; not read on a crop.","via":"harvest"}}]},"well_roll_bottom_y":{"label":"The roll along the top of the well's right wall, its lower edge, Y","kind":"length","measurements":[{"id":"right","value":-0.202,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 842fbe8fe0ba (the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467)","scaleRef":"a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face","method":"picked at px (1860, 518) on a gridded crop (scratch/crop.py), carried through that frame: the dark crease under the roll, level along the well","via":"harvest"}}]},"well_roll_rear_x":{"label":"The roll along the top of the well's right wall, its rear end, X","kind":"length","measurements":[{"id":"right","value":2.78,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 842fbe8fe0ba (the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467)","scaleRef":"a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face","method":"picked at px (1590, 470) on a gridded crop (scratch/crop.py), carried through that frame: where the roll's lit crest begins over the fence's rear","via":"harvest"}}]},"well_roll_front_x":{"label":"The roll's flat front end beside the pivot lug, X","kind":"length","measurements":[{"id":"right","value":6.181,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-lower-receiver 842fbe8fe0ba (the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467)","scaleRef":"a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face","method":"picked at px (2046, 492) on a gridded crop (scratch/crop.py), carried through that frame: the roll's front end, beside the pivot pin's head","via":"harvest"}}]},"well_roll_crest_out":{"label":"The roll along the top of the magazine well's right wall, its crest from the centre plane (Z)","kind":"length","measurements":[{"id":"assumed","value":0.8,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file looks along the receiver: drawn as far out as the forged mil-spec roll the catalog has read through a camera (the Workhorse's 0.80, which Bear Creek's takes too). The right photo has this roll's lower edge at -0.202 and its front end at 6.181, where the Workhorse's are -0.204 and 6.231: one forging pattern.","via":"harvest"}}]},"well_roll_rear_round":{"label":"The roll's rear end, its rounding","kind":"length","measurements":[{"id":"assumed","value":0.1,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the rear end is round on the right photo, over about this much; not read.","via":"harvest"}}]},"guard_width":{"label":"The trigger guard, its width across (Z)","kind":"length","measurements":[{"id":"assumed","value":0.442,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the guard is drawn as wide as the gap between the ears it is pinned in (std.ar15.trigger_guard_ear_gap, the drawing's .438 +.008; the script asserts it is no wider). BCM's photo of it installed, from below and ahead (c50cd1de432a), has its bar no wider than the ears; no view on file is square to it.","via":"harvest"}}]},"guard_rear_end_x":{"label":"The trigger guard, its rear end inside the rear ears, X","kind":"length","measurements":[{"id":"assumed","value":1.3,"unit":"in","pm":0.08,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: hidden between the rear ears: the guard's end is drawn 0.2 in behind its roll pin, as far as the ears reach behind it on the right photo (their rear face at the grip's front, 1.29).","via":"harvest"}}]},"guard_front_end_x":{"label":"The trigger guard, its front end inside the front ears, X","kind":"length","measurements":[{"id":"assumed","value":3.47,"unit":"in","pm":0.06,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: hidden between the front ears: drawn to the well's rear wall (std.ar15.magwell_front_inner_x less std.ar15.magwell_length, 3.472), past its front hole.","via":"harvest"}}]},"guard_tab_top_y":{"label":"The trigger guard's two ends between the ears, their top, Y","kind":"length","measurements":[{"id":"assumed","value":-2.03,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: hidden between the ears: drawn up to where the guard's upper edge goes behind them on the right photo (-2.09 at the rear, -2.03 at the front), level.","via":"harvest"}}]},"guard_edge_r":{"label":"The trigger guard's edges, their rounding","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: a moulded guard's edges are round (BCM: \"No sharp edges, which increases comfort\"); how round isn't read on any photo on file.","via":"harvest"}}]}}},{"subject":"bcm-mk2-receiver-extension","title":"BCM MK2 Receiver Extension (the MK2 recoil mitigation system's tube)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"metal","value":4.2,"unit":"oz","pm":0.3,"source":{"type":"derived","expr":"(0.785398163 * ({.tube_od} * {.tube_od} - {std.receiver_extension.bore_d} * {std.receiver_extension.bore_d}) * {.tube_length} + 0.785398163 * {std.receiver_extension.bore_d} * {std.receiver_extension.bore_d} * {.rear_wall} + {std.receiver_extension.rail_width} * ({std.receiver_extension.rail_bottom_below_axis} - {.tube_od} / 2) * ({.tube_length} - ({.rail_ramp_start} + {.rail_ramp_end}) / 2) - 8 * 0.785398163 * {.position_hole_d} * {.position_hole_d} * ({std.receiver_extension.rail_bottom_below_axis} - {.tube_od} / 2) - {.channel_width} * {.channel_depth} * 7 * {.position_step}) * {std.density.aluminium_7075}","via":"harvest"},"note":"Its own sizes, not a carbine tube's 3.76 oz scaled."}],"note":"No maker's or seller's figure: BCM states none for the extension alone. Worked out from its sizes as 7075 (BCM: \"Machined from 7075T6\"): the tube's wall round its bore along its length, its rear wall, the rail from the middle of its ramp back, less the eight holes and the channel they are in. The model drawn from the same sizes is held to it in its test."},"tube_od":{"label":"The tube's outside diameter","kind":"length","measurements":[{"id":"std","value":1.148,"unit":"in","stated":"manufactured to Mil-Spec dimensions and specifications. Mil-Spec receiver extensions have a slightly smaller dimension where the stock slides on.","source":{"type":"derived","expr":"{std.receiver_extension.milspec_od}","basis":"BCM, MK2 Receiver Extension (https://bravocompanyusa.com/bcm-MK2-receiver-extension/, read on the harvested copy 2026-10-28), and its kit pages: \"Mil-Spec diameter\"","via":"harvest"}},{"id":"photo","value":1.148,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/bcm-mk2-receiver-extension 9b4a404f493e (BCM's BCM-INTERMEDIATE-RE-2: the tube's left side on white, thread to the left, 2166 x 800)","scaleRef":"its own thread, 16 to the inch (std.receiver_extension.thread_pitch): sixteen pitches along the silhouette's lower edge, 222 px (13.875 px a pitch, 222.0 px/in); the upper edge's ten 13.8","method":"the body's silhouette, 206.7 to 461.6 at its middle row's threshold crossings, 254.9 px, between the thread's relief and the rail's ramp (x 500 to 670)","via":"harvest"},"note":"A matte tube on white, 255 px tall: the edge's blur is a pixel in 255. The two agree to the pixel."}],"adopt":{"from":"std","reason":"BCM says it is made to mil-spec dimensions; its own photo, scaled by the thread, reads the same."}},"tube_length":{"label":"The tube's length (its front face to its rear face)","kind":"length","measurements":[{"id":"photo","value":7.955,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-mk2-receiver-extension 9b4a404f493e (BCM's BCM-INTERMEDIATE-RE-2: the tube's left side on white, 2166 x 800)","scaleRef":"its own thread, 16 to the inch: 222.0 px/in (tube_od's photo reading); the body's 254.9 px is the mil-spec 1.148 at that scale","method":"the silhouette's ends on the axis row: the thread's front rim at x 152.5, the rear face's rim at 1918.5 (both ends' faces are turned away from the lens, so each end is its rim, in the axis's plane): 1766 px","via":"harvest"},"note":"The ± is a fifth of a pixel a pitch over sixteen pitches, and the ends' half pixel. Corroborated by the free spring BCM shows beside it: in its kit photo (references/bcm-mk2-receiver-extension da2d35d9e02d) the tube is 525.5 px and the M16 rifle spring 824.7 px, which at this length is 12.48 in, where the Army's drawing of that spring has 12.50 (bcm-rifle-m16-action-spring.free_length)."},{"id":"bcm-sentence","value":8,"unit":"in","pm":0.1,"stated":"Mk2 Receiver Extension (approximately 3/4” longer than carbine), 7076T6, 8 position, Mil-Spec diameter","source":{"type":"derived","expr":"{bcm-receiver-extension.tube_length} + 0.75in","basis":"BCM, MK2 Recoil Mitigation System - Mod 1 - T0, T1 and T2 (https://bravocompanyusa.com/bcm-mk2-recoil-mitigation-system-mod-1-t0/, read on the harvested copy 2026-10-28) and Stock Kit Mod 2 MK2RMS: \"approximately 3/4” longer than carbine\", added to the carbine tube on file (bcm-receiver-extension.tube_length, the generic 7.25)","via":"harvest"},"note":"Approximate on both counts: BCM's \"approximately\" and a carbine length that two generic pages give. BCM's maker site says of the system \"the use of an M16A4 rifle spring in an rifle length buffer tube\" (https://bravocompanymfg.com/accessories-rms-mk2.html): a rifle's extension is far longer than either figure here, and the photo and the kit pages agree that it is the intermediate length."}],"adopt":{"from":"photo","reason":"Read on BCM's own photo at the scale of its own thread, and corroborated by the free M16 spring beside it; BCM's \"approximately 3/4” longer\" over a generic carbine length agrees within its ±."}},"tube_front_behind_pin":{"label":"The tube's front face behind the takedown pin","kind":"length","measurements":[{"id":"std","value":0.669,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"-{std.receiver_extension.front_face_x}","basis":"A mil-spec thread screwed home over the buffer retainer's shoulder (the Army's drawings): BCM, \"manufactured to Mil-Spec dimensions\"","via":"harvest"}}]},"thread_length":{"label":"The thread's length from the tube's front face","kind":"length","measurements":[{"id":"photo","value":1.295,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-receiver-extension 9b4a404f493e (BCM's side view on white, 2166 x 800)","scaleRef":"its own thread, 222.0 px/in (tube_length)","method":"the silhouette's crests and roots along both edges, from the front rim at x 152.5 to the last root at 434 below and 426 above and the plain band from 442: 287.5 px","via":"harvest"}}],"note":"The carbine's (std.receiver_extension.thread_length, the reference model's) is 1.181: this tube's runs a tenth further, to a plain band before the body (relief_length)."},"relief_d":{"label":"The plain band between the thread and the body: its diameter","kind":"length","measurements":[{"id":"photo","value":1.12,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-mk2-receiver-extension 9b4a404f493e (BCM's side view on white, 2166 x 800)","scaleRef":"its own thread, 222.0 px/in","method":"the silhouette from x 442 to 474, 207.6 to 456.3: 248.7 px","via":"harvest"},"note":"Just over the thread's minor diameter (1.109): a thread relief, also seen as a band in Primary Arms' oblique photo (6894abcbdefc)."}]},"relief_length":{"label":"The plain band between the thread and the body: its length","kind":"length","measurements":[{"id":"photo","value":0.144,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-mk2-receiver-extension 9b4a404f493e (BCM's side view on white, 2166 x 800)","scaleRef":"its own thread, 222.0 px/in","method":"from the thread's last root (x 440) to the body's shoulder (x 474): 32 px","via":"harvest"}}]},"rear_wall":{"label":"The tube's rear wall, its thickness","kind":"length","measurements":[{"id":"assumed","value":0.072,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{std.receiver_extension.carbine_rear_wall}","basis":"An assumption for the drawing, not a reading: no view on file shows this tube's rear face or a section of it; a mil-spec carbine extension's (the reference model's) is taken.","via":"harvest"}}]},"vent_d":{"label":"The hole through the rear wall, its diameter","kind":"length","measurements":[{"id":"assumed","value":0.094,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{std.receiver_extension.carbine_vent_d}","basis":"An assumption for the drawing, not a reading: no view on file shows this tube's rear face; a mil-spec carbine extension's vent (the reference model's) is taken.","via":"harvest"}}]},"rail_ramp_start":{"label":"The rail's front ramp: where it leaves the tube, from the tube's front face","kind":"length","measurements":[{"id":"photo","value":2.35,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-mk2-receiver-extension 9b4a404f493e (BCM's side view on white, 2166 x 800)","scaleRef":"its own thread, 222.0 px/in","method":"the silhouette's lower edge leaves the tube's (461.6) at x 674, 521.5 px behind the front rim","via":"harvest"},"note":"The mil-spec carbine tube's begins at 2.326 (std.receiver_extension.rail_ramp_start)."}]},"rail_ramp_end":{"label":"The rail's front ramp: where it reaches the rail's full depth, from the tube's front face","kind":"length","measurements":[{"id":"photo","value":2.9,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-receiver-extension 9b4a404f493e (BCM's side view on white, 2166 x 800)","scaleRef":"its own thread, 222.0 px/in","method":"the lower edge reaches the rail's bottom (524) at x 797: a straight ramp of 29 degrees from x 674 (14 px down every 25 along)","via":"harvest"},"note":"Shallower than a mil-spec carbine tube's 45 degree ramp (std.receiver_extension.rail_ramp_end, 2.592)."}]},"rail_rear_chamfer":{"label":"The rail's rear end, cut back at 45 degrees: its length along the tube","kind":"length","measurements":[{"id":"photo","value":0.28,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-receiver-extension 9b4a404f493e (BCM's side view on white, 2166 x 800)","scaleRef":"its own thread, 222.0 px/in","method":"the lower edge leaves the rail's bottom at x 1852 and rises at 49 degrees to the tube's own at the rear rim (1912): 62 px","via":"harvest"}}]},"position_hole_d":{"label":"The position holes, diameter","kind":"length","measurements":[{"id":"photo","value":0.326,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-mk2-receiver-extension 1593b85764de (BCM's _TCK9381: the tube's underside on white, thread to the left, 1280 x 854)","scaleRef":"the tube's length, 1136 px for 7.955 in (tube_length): 142.8 px/in at the axis; the rail's 0.49 (std.receiver_extension.rail_width) reads 68 px, the same scale to a pixel","method":"each of the eight round holes' outlines on a 2.86x crop, 46.5 px across","via":"harvest"}}]},"position_hole_front_from_face":{"label":"The front position hole (the stock collapsed): its centre behind the tube's front face","kind":"length","measurements":[{"id":"photo","value":3.506,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-receiver-extension 1593b85764de (BCM's underside view on white, 1280 x 854)","scaleRef":"142.8 px/in (position_hole_d)","method":"the hole's centre at x 576.7 (the middle of its dark half on rows 418 to 426, and of its outline on the crop), the front rim at 76: 500.7 px","via":"harvest"},"note":"Where the carbine tube on file has its front hole (bcm-receiver-extension: 7.25 − 0.44 − 5 × 0.66 = 3.51): the stock collapses to the same place, and the MK2's two more holes are behind."}]},"position_pitch_front":{"label":"The position holes' spacing, the front three","kind":"length","measurements":[{"id":"photo","value":0.605,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-mk2-receiver-extension 1593b85764de (BCM's underside view on white, 1280 x 854)","scaleRef":"142.8 px/in (position_hole_d)","method":"the holes' centres at x 576.7, 662.8 and 749.6: 86.1 and 86.8 px","via":"harvest"}}]},"position_pitch_rear":{"label":"The position holes' spacing, the rear six","kind":"length","measurements":[{"id":"photo","value":0.531,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-mk2-receiver-extension 1593b85764de (BCM's underside view on white, 1280 x 854)","scaleRef":"142.8 px/in (position_hole_d)","method":"the holes' centres at x 749.6, 825.2, 901.5, 976.8, 1052.7 and 1129.0: 75.6 to 76.3 px apart, 75.9 on average","via":"harvest"},"note":"The rear hole is then 0.58 in ahead of the rear face (7.955 − 3.506 − 2 × 0.605 − 5 × 0.531), as it reads (1212 − 1129 = 83 px)."}],"note":"Counted: eight round holes in a channel along the rail, the three in front spaced wider than the six behind (the third is in both rows). Two crops of the photo and its row profiles give the same centres."},"position_step":{"label":"The stock position step (the holes' mean spacing, front to rear)","kind":"length","measurements":[{"id":"holes","value":0.552,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"(2 * {.position_pitch_front} + 5 * {.position_pitch_rear}) / 7","via":"harvest"}}],"note":"What the app moves a stock by a position: one step for all eight. The holes aren't evenly spaced (position_pitch_front, position_pitch_rear): with this mean, the first and the eighth positions are where their holes are, and those between up to 0.06 in off theirs."},"channel_width":{"label":"The channel the holes are in, along the rail: its width","kind":"length","measurements":[{"id":"photo","value":0.343,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-mk2-receiver-extension 1593b85764de (BCM's underside view on white, 1280 x 854)","scaleRef":"142.8 px/in (position_hole_d)","method":"its two edges on a 2.86x crop, 49 px apart; its ends are round about the first and the last hole's centres","via":"harvest"}}]},"channel_depth":{"label":"The channel along the rail: its depth","kind":"length","measurements":[{"id":"assumed","value":0.04,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the only view of the channel is from straight under it, where its depth doesn't show; no section or end view of the rail is on file.","via":"harvest"}}]},"front_slot_end_from_face":{"label":"The long slot at the rail's front: its round rear end, behind the tube's front face","kind":"length","measurements":[{"id":"photo","value":3.13,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-receiver-extension 1593b85764de (BCM's underside view on white, 1280 x 854)","scaleRef":"142.8 px/in (position_hole_d)","method":"on a 3x crop: a slot as wide as a hole runs from the foot of the ramp (x 410, which the side view has at 2.35) back to its round end at x 523: 447 px behind the front rim","via":"harvest"}}]},"rear_notch_depth":{"label":"The notch in the rail's rear end: how far it reaches in from the rear face","kind":"length","measurements":[{"id":"photo","value":0.26,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-receiver-extension 1593b85764de (BCM's underside view on white, 1280 x 854)","scaleRef":"142.8 px/in (position_hole_d)","method":"on a 2.86x crop: a U as wide as a hole, open at the rear face (x 1212), its round end at x 1174.5: 37.5 px","via":"harvest"}}]}}},{"subject":"bcm-pmcr-carbine","title":"BCM® PMCR (Polymer M-LOK® Compatible Rail)* Carbine Length-BLACK (BCM-PMCR-CAR-BLK)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"bcm","value":4.48,"unit":"oz","stated":"Natural ergonomics; slim, comfortable and lightweight, only 4.48 ounces","source":{"type":"spec","publisher":"manufacturer","name":"BCM, BCM® PMCR (Polymer M-LOK® Compatible Rail)* Carbine Length-BLACK","url":"https://bravocompanyusa.com/bcm-pmcr-polymer-m-lok-rail-carbine-length-black/","retrieved":"2026-10-28","via":"harvest"}}],"note":"The two halves, the lower one with its aluminium heat shield. No seller on file restates it."},"length":{"label":"Length, overall","kind":"length","measurements":[{"id":"photo","value":7.28,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"its three upper M-LOK slots, centres 267.15 px apart (265.5 and 268.8) for the standard's 40 mm (std.mlok.slot_pitch): 169.6 px/in","method":"the outline (luminance under 200) from its rear end (column 22, the spine's tab over the ring; the upper flange's end at 26) to its front face (column 1257): 1235 px; ± 0.5% for the slots' scatter and the depth between the slots' faces and the outline's edges","via":"harvest"}}],"note":"BCM states no length. From its rear end, which bears on the delta ring's lip, to its front face, which stands ahead of the front sight base's rear face (the front hook and the upper half's front chamfer included)."},"width":{"label":"Width (the upper half, across its sides)","kind":"length","measurements":[{"id":"photo","value":1.854,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 291dadf219c1 (BCM's gallery photo STKL8997: the two halves apart, the upper one from above, 1280 x 853)","scaleRef":"the upper half's own two rows of three M-LOK slots, centres 278.6 px apart for the standard's 40 mm: 176.9 px/in","method":"the upper half's silhouette across it at column 600 (rows 462 to 790): 328 px; ± 4 px","via":"harvest"}},{"id":"mid-photo","value":1.873,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 530bce1646cf (BCM's gallery photo STKL8993: the mid-length's two halves apart, the upper one from above, 1280 x 853)","scaleRef":"its own rows of four M-LOK slots, 216.1 px apart: 137.2 px/in","method":"the upper half across it at column 1019 (rows 505 to 762): 257 px; ± 4 px: the mid-length's, the same section by every photo of the two","via":"harvest"}}],"adopt":{"from":"photo","reason":"The carbine-length's own photo; the mid-length's, the same section, agrees within the two ±."}},"lower_width":{"label":"The lower half's width (it stands inside the upper one's sides at the seam)","kind":"length","measurements":[{"id":"photo","value":1.745,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 291dadf219c1 (BCM's gallery photo STKL8997: the two halves apart, the lower one from below, 1280 x 853)","scaleRef":"the lower half's own row of three M-LOK slots, 269 px apart for the standard's 40 mm: 170.8 px/in","method":"the lower half's silhouette across it at column 600 (rows 76 to 374): 298 px; ± 4 px","via":"harvest"}}]},"height":{"label":"Height, excluding the front hook","kind":"length","measurements":[{"id":"photo","value":2.176,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"its three upper M-LOK slots, centres 267.15 px apart (265.5 and 268.8) for the standard's 40 mm (std.mlok.slot_pitch): 169.6 px/in","method":"the outline's top (row 242, the spine) to the body's bottom (row 611) at column 700, clear of the hook: 369 px; ± 3 px","via":"harvest"}}],"note":"BCM gives no height."},"top_above_axis":{"label":"Its top (the spine's tab at its rear end, the outline's highest point) above the bore axis","kind":"length","measurements":[{"id":"photo","value":1.294,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"its three upper M-LOK slots, centres 267.15 px apart (265.5 and 268.8) for the standard's 40 mm (std.mlok.slot_pitch): 169.6 px/in","method":"the bore axis at row 458.5, the middle of its rear flanges (rows 321 and 596 at column 46), which stand in the delta ring round the barrel nut; the outline's highest point, the spine's tab over the ring (row 239): 219.5 px; ± 3 px. The spine along its length stands at row 242, 0.02 lower","via":"harvest"}}]},"bottom_below_axis":{"label":"Its body's bottom (clear of the hook) below the bore axis","kind":"length","measurements":[{"id":"photo","value":0.899,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"its three upper M-LOK slots, centres 267.15 px apart (265.5 and 268.8) for the standard's 40 mm (std.mlok.slot_pitch): 169.6 px/in","method":"the axis (row 458.5) to the body's bottom (row 611) at columns 300 to 700: 152.5 px; ± 3 px","via":"harvest"}}]},"inside_diameter":{"label":"Inside diameter","kind":"length","measurements":[],"note":"BCM gives none, and no photo looks into an end. The model's inside is its outside less the wall (wall), which no view gives either."},"rear_x":{"label":"Its rear end (bearing on the delta ring's lip) ahead of the receiver's front face","kind":"length","measurements":[{"id":"derived","value":0.336,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{std.ar15.slip_ring_front_x}","via":"harvest"}}],"note":"Where the standard's delta ring holds it (std.ar15.slip_ring_front_x, from the Army's drawings): its rear flanges in the ring, against the lip. BCM's instructions (this page's picture of them, e0a7762984ab): \"pull the Delta Ring to the furthest rearward position, enough to allow the rear of the PMCR to interface with the Barrel Nut teeth. The upper handguard will surround and index to the barrel nut enough to let the Delta Ring travel forward to secure the upper handguard in place\"."},"body_rear_x":{"label":"Its body's rear face (behind which its rear flanges and the spine's tab stand), from its rear end","kind":"length","measurements":[{"id":"photo","value":0.2,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"its three upper M-LOK slots, centres 267.15 px apart (265.5 and 268.8) for the standard's 40 mm (std.mlok.slot_pitch): 169.6 px/in","method":"the body's whole height begins at column 56 (rows 239 to 601) against the rear end (22): 34 px; ± 2 px","via":"harvest"}}]},"rear_collar_od":{"label":"Its rear flanges (what stands in the delta ring round the barrel nut), outside diameter","kind":"length","measurements":[{"id":"photo","value":1.621,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"its three upper M-LOK slots, centres 267.15 px apart (265.5 and 268.8) for the standard's 40 mm (std.mlok.slot_pitch): 169.6 px/in","method":"the upper flange's top (row 321) to the lower flange's bottom (row 596) at column 46, where both are whole: 275 px; ± 4 px for their rounded rear edges","via":"harvest"}}],"note":"Inside the delta ring's bore (std.ar15.slip_ring_bore_d, 1.75), and about the barrel nut's toothed flange (std.ar15.barrel_nut_flange_od, 1.56) and a wall: BCM's instructions have the rear of the PMCR \"interface with the Barrel Nut teeth\", so its flanges stand round the teeth and in their notches, which the nut's model has as a ring; what the two share there is said in the part."},"rear_collar_gap":{"label":"The gap between its two halves' rear flanges at each side (where the backdrop shows through)","kind":"length","measurements":[{"id":"photo","value":0.436,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"its three upper M-LOK slots, centres 267.15 px apart (265.5 and 268.8) for the standard's 40 mm (std.mlok.slot_pitch): 169.6 px/in","method":"the backdrop through the rear end at column 46: rows 437 to 511, 74 px; ± 3 px","via":"harvest"}}]},"rear_collar_gap_y":{"label":"That gap's middle above the bore axis (negative below)","kind":"length","measurements":[{"id":"photo","value":-0.091,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"its three upper M-LOK slots, centres 267.15 px apart (265.5 and 268.8) for the standard's 40 mm (std.mlok.slot_pitch): 169.6 px/in","method":"the gap's middle (row 474) less the axis (row 458.5): 15.5 px under it; ± 3 px","via":"harvest"}}]},"seam_y":{"label":"The seam between its two halves, on the sides, above the bore axis (negative below)","kind":"length","measurements":[{"id":"photo","value":-0.339,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"its three upper M-LOK slots, centres 267.15 px apart (265.5 and 268.8) for the standard's 40 mm (std.mlok.slot_pitch): 169.6 px/in","method":"the dark band where the upper half's side ends over the lower half (rows 504 to 528 at columns 300 to 700), its middle 516: 57.5 px under the axis; ± 5 px","via":"harvest"}}],"note":"The upper half reaches below the axis; the lower one, narrower (lower_width), stands inside its sides along the seam."},"side_top_y":{"label":"Where the upper half's upright side meets its M-LOK face, above the bore axis","kind":"length","measurements":[{"id":"photo","value":0.5,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"its three upper M-LOK slots, centres 267.15 px apart (265.5 and 268.8) for the standard's 40 mm (std.mlok.slot_pitch): 169.6 px/in","method":"the change from the face's lit band to the side's textured one: row 372 at columns 500 and 700, 376 at 300: 85 px over the axis; ± 3 px","via":"harvest"}}]},"mlok_side_slots":{"label":"M-LOK slots in each upper face (the 10:30 and 1:30 rows)","kind":"count","measurements":[{"id":"bcm","value":3,"unit":"count","stated":"Three, three-hole M-LOK® compatible mounting slots, mounting surfaces (10:30, 1:30, and 6:00 o'clock placements)","source":{"type":"spec","publisher":"manufacturer","name":"BCM, BCM® PMCR (Polymer M-LOK® Compatible Rail)* Carbine Length-BLACK","url":"https://bravocompanyusa.com/bcm-pmcr-polymer-m-lok-rail-carbine-length-black/","retrieved":"2026-10-28","via":"harvest"}},{"id":"photo","value":3,"unit":"count","source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"none: a count","method":"three see-through slots in the right upper row; three in the left's on e380434eed29, and in both upper rows and the lower row on 291dadf219c1","via":"harvest"}}],"adopt":{"from":"bcm","reason":"BCM's \"three-hole\" for each of the three, counted on its photos."}},"mlok_side_slot0_x":{"label":"The upper rows' rearmost M-LOK slot (its centre), from its rear end","kind":"length","measurements":[{"id":"photo","value":2.343,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"its three upper M-LOK slots, centres 267.15 px apart (265.5 and 268.8) for the standard's 40 mm (std.mlok.slot_pitch): 169.6 px/in","method":"the rearmost slot's centre (column 419.3, the see-through region's middle) from the rear end (22): 397.3 px; ± 2 px. The next two at 684.8 and 953.6: the standard's pitch to 0.6%","via":"harvest"}}]},"mlok_side_slot_y":{"label":"The upper rows' slot centres above the bore axis","kind":"length","measurements":[{"id":"photo","value":0.806,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"its three upper M-LOK slots, centres 267.15 px apart (265.5 and 268.8) for the standard's 40 mm (std.mlok.slot_pitch): 169.6 px/in","method":"the slot's near rim, rows 306 to 338 at columns 500 and 700 (its upper wall's shadow over the see-through part): centre 322, 136.5 px over the axis; ± 3 px","via":"harvest"}}]},"mlok_side_slot_z":{"label":"The upper rows' see-through slits, seen from above, out from the middle (to each side)","kind":"length","measurements":[{"id":"photo","value":0.539,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 291dadf219c1 (BCM's gallery photo STKL8997: the two halves apart, the upper one from above, 1280 x 853)","scaleRef":"the upper half's own two rows of three M-LOK slots, centres 278.6 px apart for the standard's 40 mm: 176.9 px/in","method":"the two rows' see-through slits, centres at rows 531.8 and 722.6: 95.4 px each side of their middle; ± 2 px","via":"harvest"}}],"note":"Not the slots' centres: from above, the upper half's own side under each face hides the outer part of what shows through a slot, so the slit stands inward of the slot. Not used by the model (mlok_side_face_distance is the face's place); kept as the reading it is."},"mlok_side_face_angle":{"label":"The upper M-LOK faces' outward direction about the bore axis, from straight up (degrees)","kind":"angle","measurements":[{"id":"bcm","value":45,"unit":"deg","stated":"Three, three-hole M-LOK® compatible mounting slots, mounting surfaces (10:30, 1:30, and 6:00 o'clock placements)","source":{"type":"spec","publisher":"manufacturer","name":"BCM, BCM® PMCR (Polymer M-LOK® Compatible Rail)* Carbine Length-BLACK","url":"https://bravocompanyusa.com/bcm-pmcr-polymer-m-lok-rail-carbine-length-black/","retrieved":"2026-10-28","via":"harvest"}},{"id":"photo","value":43,"unit":"deg","pm":4,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"its three upper M-LOK slots, centres 267.15 px apart (265.5 and 268.8) for the standard's 40 mm (std.mlok.slot_pitch): 169.6 px/in","method":"two readings: the face runs from where the upright side ends (side_top_y, 0.50 up, at the half width, width / 2) to where it meets the spine (spine_vent_y, 1.10 up, at the spine's half width, spine_half_width): 0.60 up over 0.633 in, its outward direction 43.5° from up; and the slot's near rim, 32 px tall in the level side view (rows 306 to 338), is the standard's 7 mm (std.mlok.slot_width) times the sine of 43°","via":"harvest"}}],"adopt":{"from":"photo","reason":"BCM's \"10:30, 1:30\" says which faces; the photo's own edges put them at 43 degrees from up, within its ± of BCM's 45. The accessories stand out at the angle the faces have."}},"mlok_side_face_distance":{"label":"The upper M-LOK faces' distance from the bore axis (along their outward direction)","kind":"length","measurements":[{"id":"derived","value":0.998,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.width} / 2 * sin({.mlok_side_face_angle}) + {.side_top_y} * cos({.mlok_side_face_angle})","via":"harvest"}}],"note":"The plane through the face's lower edge (the upright side's top at the half width) at the faces' angle: it meets the spine at spine_vent_y, and the slots' centres, which the level photo has 0.806 up, stand 0.08 up the face from where its normal through the axis meets it (where an accessory is placed)."},"mlok_bottom_slots":{"label":"M-LOK slots in the underside (six o'clock)","kind":"count","measurements":[{"id":"bcm","value":3,"unit":"count","stated":"Three, three-hole M-LOK® compatible mounting slots, mounting surfaces (10:30, 1:30, and 6:00 o'clock placements)","source":{"type":"spec","publisher":"manufacturer","name":"BCM, BCM® PMCR (Polymer M-LOK® Compatible Rail)* Carbine Length-BLACK","url":"https://bravocompanyusa.com/bcm-pmcr-polymer-m-lok-rail-carbine-length-black/","retrieved":"2026-10-28","via":"harvest"}},{"id":"photo","value":3,"unit":"count","source":{"type":"photo","photo":"references/bcm-pmcr-carbine 291dadf219c1 (BCM's gallery photo STKL8997: the two halves apart, the lower one from below, 1280 x 853)","scaleRef":"none: a count","method":"three slots along the lower half's middle, the heat shield bright through them","via":"harvest"}}],"adopt":{"from":"bcm","reason":"BCM's figure, counted on its photo."}},"mlok_bottom_slot0_x":{"label":"The underside's rearmost M-LOK slot (its centre), from its rear end","kind":"length","measurements":[{"id":"photo","value":1.77,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 291dadf219c1 (BCM's gallery photo STKL8997: the two halves apart, the lower one from below, 1280 x 853)","scaleRef":"the lower half's own row of three M-LOK slots, 269 px apart for the standard's 40 mm: 170.8 px/in","method":"the slots' see-through middles along row 215 at columns 593 and 862 (the rearmost is broken by the shield behind it, its middle near 323: one pitch behind the second, 324) less the lower half's rear end (column 20): 304 px; ± 0.06 in for the lower half's rear end against the upper's","via":"harvest"}}]},"mlok_bottom_face_distance":{"label":"The underside's M-LOK face, its distance below the bore axis","kind":"length","measurements":[{"id":"derived","value":0.899,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{.bottom_below_axis}","via":"harvest"}}]},"reach_inside":{"label":"The room inside its M-LOK faces before what runs through it (how far an accessory's nuts may reach in)","kind":"length","measurements":[],"note":"Depends on the barrel, the gas tube and the heat shield, and on the wall, which no view gives: no figure, so the check reads as unmade."},"bottom_half_width":{"label":"Its underside's flat (where the six o'clock slots are), half its width","kind":"length","measurements":[{"id":"assumed","value":0.3,"unit":"in","pm":0.08,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the lower half from below (291dadf219c1) shows its slot row between its two rows of vents on faces turned down and out; the flat is taken as the slot's 7 mm and a margin each side as wide as the webs between the vents and the slots.","via":"harvest"}}]},"vent_count":{"label":"The vents along each lower side (through to the heat shield)","kind":"count","measurements":[{"id":"photo","value":5,"unit":"count","source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"none: a count","method":"five dark runs along row 598; five in each row either side of the six o'clock slots on 291dadf219c1, the shield bright through them","via":"harvest"}}]},"vent0_x":{"label":"The rearmost lower vent's middle, from its rear end","kind":"length","measurements":[{"id":"photo","value":1.4,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"its three upper M-LOK slots, centres 267.15 px apart (265.5 and 268.8) for the standard's 40 mm (std.mlok.slot_pitch): 169.6 px/in","method":"dark runs along row 598 (luminance under 45), centres 259.5, 434, 607, 780, 953: the rearmost 237.5 px ahead of the rear end; ± 2 px","via":"harvest"}}]},"vent_pitch":{"label":"The lower vents, middle to middle","kind":"length","measurements":[{"id":"photo","value":1.022,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"its three upper M-LOK slots, centres 267.15 px apart (265.5 and 268.8) for the standard's 40 mm (std.mlok.slot_pitch): 169.6 px/in","method":"the first to the last, 693.5 px over four gaps: 173.4 px each","via":"harvest"}}]},"vent_length":{"label":"Each lower vent's length along it","kind":"length","measurements":[{"id":"photo","value":0.607,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"its three upper M-LOK slots, centres 267.15 px apart (265.5 and 268.8) for the standard's 40 mm (std.mlok.slot_pitch): 169.6 px/in","method":"the dark runs along row 598: 103 to 104 px","via":"harvest"}}]},"vent_y":{"label":"The lower vents' middles above the bore axis (negative below)","kind":"length","measurements":[{"id":"photo","value":-0.811,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"its three upper M-LOK slots, centres 267.15 px apart (265.5 and 268.8) for the standard's 40 mm (std.mlok.slot_pitch): 169.6 px/in","method":"the dark run at column 300, rows 586 to 606: middle 596, 137.5 px under the axis; ± 5 px","via":"harvest"}}]},"vent_z":{"label":"The lower vents' middles out from the middle (to each side)","kind":"length","measurements":[{"id":"photo","value":0.451,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 291dadf219c1 (BCM's gallery photo STKL8997: the two halves apart, the lower one from below, 1280 x 853)","scaleRef":"the lower half's own row of three M-LOK slots, 269 px apart for the standard's 40 mm: 170.8 px/in","method":"the two rows of vents at column 452, middles at rows 128 and 282: 77 px each side of their middle; ± 4 px","via":"harvest"}}]},"vent_width":{"label":"Each lower vent's width across it","kind":"length","measurements":[{"id":"photo","value":0.14,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 291dadf219c1 (BCM's gallery photo STKL8997: the two halves apart, the lower one from below, 1280 x 853)","scaleRef":"the lower half's own row of three M-LOK slots, 269 px apart for the standard's 40 mm: 170.8 px/in","method":"the lit side's vent across column 452 (rows 116 to 140): 24 px; ± 3 px, on a face turned partly away from the lens","via":"harvest"}}]},"spine_half_width":{"label":"The spine along its top (the outer edges of its two rows of pockets), half its width","kind":"length","measurements":[{"id":"photo","value":0.294,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 291dadf219c1 (BCM's gallery photo STKL8997: the two halves apart, the upper one from above, 1280 x 853)","scaleRef":"the upper half's own two rows of three M-LOK slots, centres 278.6 px apart for the standard's 40 mm: 176.9 px/in","method":"the two rows of pockets along the top, their outer edges at rows 576 and 680 (on a crop at twice the size): 52 px each side of their middle (628); ± 3 px","via":"harvest"}}]},"spine_vent_y":{"label":"The bottom of the spine (where the M-LOK faces meet it, the windows' sills), above the bore axis","kind":"length","measurements":[{"id":"photo","value":1.1,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"its three upper M-LOK slots, centres 267.15 px apart (265.5 and 268.8) for the standard's 40 mm (std.mlok.slot_pitch): 169.6 px/in","method":"the windows' lower edge and the face's lit band's top at columns 500 and 700 (rows 271 to 274): 186 px over the axis; ± 3 px","via":"harvest"}}]},"spine_groove_count":{"label":"The ribs across the spine (between its pockets, and at its ends)","kind":"count","measurements":[{"id":"photo","value":14,"unit":"count","source":{"type":"photo","photo":"references/bcm-pmcr-carbine 291dadf219c1 (BCM's gallery photo STKL8997: the two halves apart, the upper one from above, 1280 x 853)","scaleRef":"the upper half's own two rows of three M-LOK slots, centres 278.6 px apart for the standard's 40 mm: 176.9 px/in","method":"fourteen dark lines across the two rows of pockets along row 590 (columns 48 to 1196), the shadows of the ribs between them: thirteen pockets a row","via":"harvest"}}]},"spine_groove0_x":{"label":"The rearmost rib across the spine (its rear wall's shadow line), from its rear end","kind":"length","measurements":[{"id":"photo","value":0.147,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 291dadf219c1 (BCM's gallery photo STKL8997: the two halves apart, the upper one from above, 1280 x 853)","scaleRef":"the upper half's own two rows of three M-LOK slots, centres 278.6 px apart for the standard's 40 mm: 176.9 px/in","method":"the first dark line along row 590 (column 48) less the rear end (22): 26 px; ± 3 px","via":"harvest"}}]},"spine_groove_pitch":{"label":"The ribs across the spine, middle to middle","kind":"length","measurements":[{"id":"photo","value":0.499,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 291dadf219c1 (BCM's gallery photo STKL8997: the two halves apart, the upper one from above, 1280 x 853)","scaleRef":"the upper half's own two rows of three M-LOK slots, centres 278.6 px apart for the standard's 40 mm: 176.9 px/in","method":"the first to the last line, columns 48 to 1196: 1148 px over thirteen gaps, 88.3 px each","via":"harvest"}}],"note":"Half the spine's windows' pitch on the side view (spine_vent_pitch, 1.016): the two photos agree within 2%."},"spine_centre_rib":{"label":"The rib along the spine's middle, between its two rows of pockets: its width","kind":"length","measurements":[{"id":"photo","value":0.254,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 291dadf219c1 (BCM's gallery photo STKL8997: the two halves apart, the upper one from above, 1280 x 853)","scaleRef":"the upper half's own two rows of three M-LOK slots, centres 278.6 px apart for the standard's 40 mm: 176.9 px/in","method":"between the pockets' inner edges, rows 605 and 650 (on a crop at twice the size): 45 px; ± 3 px","via":"harvest"}}]},"spine_pocket_rib":{"label":"The ribs across the spine between its pockets (along it), their width","kind":"length","measurements":[{"id":"photo","value":0.15,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 291dadf219c1 (BCM's gallery photo STKL8997: the two halves apart, the upper one from above, 1280 x 853)","scaleRef":"the upper half's own two rows of three M-LOK slots, centres 278.6 px apart for the standard's 40 mm: 176.9 px/in","method":"the lit ribs between the pockets along row 590, each between a dark line at its front and one at its rear 24 to 28 px apart; ± 4 px","via":"harvest"}}],"note":"The pockets lie between the ribs, centred between the lines spine_groove0_x and spine_groove_pitch place: as long as the pitch less a rib."},"spine_rim":{"label":"The rim along the spine's outer top edge, over its pockets","kind":"length","measurements":[{"id":"assumed","value":0.04,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the level side view's top edge runs straight over the pockets (no notch where each is), so a rim stands along the top over them; from above it is a lit edge outside each pocket, 8 px on this photo (0.045 in) and 2 px on the mid-length's (0.015).","via":"harvest"}}]},"spine_slit_width":{"label":"The slit through the floor of every other pocket (by the middle rib), its width","kind":"length","measurements":[{"id":"photo","value":0.028,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 291dadf219c1 (BCM's gallery photo STKL8997: the two halves apart, the upper one from above, 1280 x 853)","scaleRef":"the upper half's own two rows of three M-LOK slots, centres 278.6 px apart for the standard's 40 mm: 176.9 px/in","method":"the backdrop seen through under alternate pockets' inner edges, rows 598 to 603 and 655 to 658: 4 to 5 px; ± 1 px","via":"harvest"}}]},"spine_vent_count":{"label":"The windows in each side of the spine, into every other pocket","kind":"count","measurements":[{"id":"photo","value":6,"unit":"count","source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"none: a count","method":"six dark windows along row 260, the rearmost half seen; the see-through slits under alternate pockets from above (291dadf219c1) agree, six a row","via":"harvest"}}]},"spine_vent0_x":{"label":"The rearmost spine window's middle, from its rear end","kind":"length","measurements":[{"id":"photo","value":0.874,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"its three upper M-LOK slots, centres 267.15 px apart (265.5 and 268.8) for the standard's 40 mm (std.mlok.slot_pitch): 169.6 px/in","method":"the windows along row 260 (luminance under 45), centres 342.5, 516.5, 688.5, 860, 1032, and the rearmost half seen at 159 to 202: the second's (1.890) less a pitch. From above, the slit under the first at 0.869","via":"harvest"}}]},"spine_vent_pitch":{"label":"The spine's windows, middle to middle","kind":"length","measurements":[{"id":"photo","value":1.016,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"its three upper M-LOK slots, centres 267.15 px apart (265.5 and 268.8) for the standard's 40 mm (std.mlok.slot_pitch): 169.6 px/in","method":"the second to the last, 689.5 px over four gaps: 172.4 px each","via":"harvest"}}]},"spine_vent_length":{"label":"Each spine window's length along it","kind":"length","measurements":[{"id":"photo","value":0.395,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"its three upper M-LOK slots, centres 267.15 px apart (265.5 and 268.8) for the standard's 40 mm (std.mlok.slot_pitch): 169.6 px/in","method":"the dark windows along row 260: 66 to 68 px","via":"harvest"}}]},"spine_vent_height":{"label":"Each spine window's height (from the spine's bottom up)","kind":"length","measurements":[{"id":"photo","value":0.1,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"its three upper M-LOK slots, centres 267.15 px apart (265.5 and 268.8) for the standard's 40 mm (std.mlok.slot_pitch): 169.6 px/in","method":"the dark window at column 500, rows 254 to 271: 17 px","via":"harvest"}}]},"front_notch_x":{"label":"The opening across the top of its front end (round the front sight base's tower): its back, from its rear end","kind":"length","measurements":[{"id":"photo","value":6.795,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 291dadf219c1 (BCM's gallery photo STKL8997: the two halves apart, the upper one from above, 1280 x 853)","scaleRef":"the upper half's own two rows of three M-LOK slots, centres 278.6 px apart for the standard's 40 mm: 176.9 px/in","method":"along the spine's middle (row 627) the polymer ends at column 1224, the rear end at column 22: 1202 px; ± 3 px. The backdrop shows from there to the faces' front tip seen from above (column 1263, 7.015 in from the rear end), which stands behind the side view's front face (length) by the front's chamfer","via":"harvest"}}]},"front_notch_half_width":{"label":"That opening's half width, at its back","kind":"length","measurements":[{"id":"photo","value":0.475,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 291dadf219c1 (BCM's gallery photo STKL8997: the two halves apart, the upper one from above, 1280 x 853)","scaleRef":"the upper half's own two rows of three M-LOK slots, centres 278.6 px apart for the standard's 40 mm: 176.9 px/in","method":"across column 1229 (0.19 in from the front), the backdrop from row 542 to row 710: 84 px each side of the middle; it widens to 0.68 at column 1245; ± 6 px","via":"harvest"}}]},"panel_top_y":{"label":"The textured panels' top edge, above the bore axis","kind":"length","measurements":[{"id":"photo","value":0.49,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"its three upper M-LOK slots, centres 267.15 px apart (265.5 and 268.8) for the standard's 40 mm (std.mlok.slot_pitch): 169.6 px/in","method":"the panels' upper edge along the side (rows 372 to 376), just under the face's lower edge: 84 px over the axis; ± 3 px","via":"harvest"}}]},"panel_bottom_y":{"label":"The textured panels' bottom edge, above the bore axis (negative below)","kind":"length","measurements":[{"id":"photo","value":-0.215,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"its three upper M-LOK slots, centres 267.15 px apart (265.5 and 268.8) for the standard's 40 mm (std.mlok.slot_pitch): 169.6 px/in","method":"the panels' lower edge (row 495, by eye along columns 350 to 1100): 36.5 px under the axis; ± 5 px","via":"harvest"}}]},"panel_rear_x":{"label":"The rearmost panel's rear end, from its rear end","kind":"length","measurements":[{"id":"photo","value":0.31,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"its three upper M-LOK slots, centres 267.15 px apart (265.5 and 268.8) for the standard's 40 mm (std.mlok.slot_pitch): 169.6 px/in","method":"the panel's rear end (column 75) less the rear end (22): 53 px; ± 6 px, by eye","via":"harvest"}}]},"panel_dividers":{"label":"The ribs between the textured panels: how many","kind":"count","measurements":[{"id":"photo","value":3,"unit":"count","source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"none: a count","method":"four panels along each side (the front one under the star), with a rib between each two; the same on the left side (e380434eed29)","via":"harvest"}}]},"panel_divider_top_x":{"label":"The first rib's top (where it meets the panels' top edge), from its rear end","kind":"length","measurements":[{"id":"photo","value":3.08,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"its three upper M-LOK slots, centres 267.15 px apart (265.5 and 268.8) for the standard's 40 mm (std.mlok.slot_pitch): 169.6 px/in","method":"column 545 less the rear end (22); ± 6 px, by eye","via":"harvest"}}]},"panel_divider1_top_x":{"label":"The second rib's top, from its rear end","kind":"length","measurements":[{"id":"photo","value":4.79,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"its three upper M-LOK slots, centres 267.15 px apart (265.5 and 268.8) for the standard's 40 mm (std.mlok.slot_pitch): 169.6 px/in","method":"column 835 less the rear end (22); ± 6 px, by eye","via":"harvest"}}]},"panel_divider2_top_x":{"label":"The third rib's top (the star panel's rear edge), from its rear end","kind":"length","measurements":[{"id":"photo","value":6.53,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"its three upper M-LOK slots, centres 267.15 px apart (265.5 and 268.8) for the standard's 40 mm (std.mlok.slot_pitch): 169.6 px/in","method":"column 1130 less the rear end (22); ± 6 px, by eye","via":"harvest"}}]},"panel_divider_bottom_x":{"label":"The first rib's foot (where it meets the panels' bottom edge), from its rear end","kind":"length","measurements":[{"id":"photo","value":1.92,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"its three upper M-LOK slots, centres 267.15 px apart (265.5 and 268.8) for the standard's 40 mm (std.mlok.slot_pitch): 169.6 px/in","method":"column 348 less the rear end (22); ± 6 px, by eye","via":"harvest"}}]},"panel_divider1_bottom_x":{"label":"The second rib's foot, from its rear end","kind":"length","measurements":[{"id":"photo","value":4.16,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"its three upper M-LOK slots, centres 267.15 px apart (265.5 and 268.8) for the standard's 40 mm (std.mlok.slot_pitch): 169.6 px/in","method":"column 728 less the rear end (22); ± 6 px, by eye","via":"harvest"}}]},"panel_divider2_bottom_x":{"label":"The third rib's foot, from its rear end","kind":"length","measurements":[{"id":"photo","value":6.39,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"its three upper M-LOK slots, centres 267.15 px apart (265.5 and 268.8) for the standard's 40 mm (std.mlok.slot_pitch): 169.6 px/in","method":"column 1105 less the rear end (22); ± 6 px, by eye","via":"harvest"}}]},"panel_rib":{"label":"The ribs between the panels, their width","kind":"length","measurements":[{"id":"photo","value":0.11,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"its three upper M-LOK slots, centres 267.15 px apart (265.5 and 268.8) for the standard's 40 mm (std.mlok.slot_pitch): 169.6 px/in","method":"the smooth ribs between the stippled panels, about 18 px across; ± 4 px, by eye","via":"harvest"}}]},"panel_depth":{"label":"How far the textured panels stand in from the side round them","kind":"length","measurements":[{"id":"assumed","value":0.015,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: BCM's \"Aggressive textured area\" is a stipple whose edge catches the light round each panel in the photos; no view shows it in section. Drawn as a shallow recess, the stipple itself not drawn.","via":"harvest"}}]},"tab_x":{"label":"The ribbed tab on the lower half's rear (over the upper half's side): its rear end, from its rear end","kind":"length","measurements":[{"id":"photo","value":0.153,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"its three upper M-LOK slots, centres 267.15 px apart (265.5 and 268.8) for the standard's 40 mm (std.mlok.slot_pitch): 169.6 px/in","method":"the tab's rear end at column 48 (the flange's run reaching down to row 461 there, to 437 at column 46) less the rear end (22); ± 3 px","via":"harvest"}}]},"tab_knee_x":{"label":"Where the ribbed tab's level top begins to fall toward its front, from its rear end","kind":"length","measurements":[{"id":"photo","value":0.755,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"its three upper M-LOK slots, centres 267.15 px apart (265.5 and 268.8) for the standard's 40 mm (std.mlok.slot_pitch): 169.6 px/in","method":"its top edge level at row 465 back from column 150, falling ahead of it to the seam at column 215: 128 px ahead of the rear end; ± 7 px, by eye","via":"harvest"}}]},"tab_front_x":{"label":"The ribbed tab's front end (at the seam), from its rear end","kind":"length","measurements":[{"id":"photo","value":1.138,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"its three upper M-LOK slots, centres 267.15 px apart (265.5 and 268.8) for the standard's 40 mm (std.mlok.slot_pitch): 169.6 px/in","method":"the tab's lower front corner at column 215: 193 px ahead of the rear end; ± 7 px, by eye","via":"harvest"}}]},"tab_top_y":{"label":"The ribbed tab's top (its rear part, level), above the bore axis","kind":"length","measurements":[{"id":"photo","value":-0.027,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","scaleRef":"its three upper M-LOK slots, centres 267.15 px apart (265.5 and 268.8) for the standard's 40 mm (std.mlok.slot_pitch): 169.6 px/in","method":"its top edge at rows 461 to 465 from column 48 to 150: 4.5 px under the axis; ± 3 px","via":"harvest"}}]},"tab_proud":{"label":"How far the ribbed tab stands out from the upper half's side","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the tab shows its lit top edge over the upper half's side in the level side views; how far it stands out isn't seen from above or an end.","via":"harvest"}}]},"mounting_length":{"label":"Its length between the ring and the cap (from its rear end to its front flange's end)","kind":"length","measurements":[{"id":"assumed","value":6.5,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: BCM states none and no photo shows the front flange, inside its front end. Taken as from its rear end on the delta ring's lip (rear_x) to the round cap's floor on BCM's 11.5 in carbine barrel (bcm-115-carbine-barrel) with BCM's F base: the cap's face on the base at 13.904 in the rifle, its floor the sheet's 0.032 behind it (bcm-handguard-cap-round-750), less the ring's lip at 7.372 (std.ar15.upper_front_face_x + std.ar15.slip_ring_front_x).","via":"harvest"}}]},"front_flange_od":{"label":"Its front flange (what goes into the round cap), outside diameter","kind":"length","measurements":[{"id":"assumed","value":1.36,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the flange goes into the cap (BCM: \"The PMCR - Carbine will only fit the \"round\" front handguard retaining cap\") and shows on no photo. Drawn round, inside the round cap's two tabs, which stand 0.690 from the axis inside (bcm-handguard-cap-round-750: tab_set_r less the sheet).","via":"harvest"}}]},"front_flange_length":{"label":"Its front flange's length (into the cap)","kind":"length","measurements":[{"id":"assumed","value":0.4,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view shows the flange. Long enough that the front wall it stands from stays behind the round cap's rim with the flange home in it (0.244 deep).","via":"harvest"}}]},"base_clearance":{"label":"How far its inside stands off the front sight base where the base stands in its front end","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no photo looks into its front end, and the real part goes on round a front sight base (BCM's instructions draw it so). The inside under the hood is cut clear of BCM's F base model (bcm-front-sight-base-f-750) as it stands with the hand guard seated in the round cap, this far off each of the base's faces.","via":"harvest"}}]},"wall":{"label":"Its polymer wall's thickness","kind":"length","measurements":[{"id":"assumed","value":0.1,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view shows an end square on or a section. Taken so that the model comes near BCM's 4.48 oz at the polymer's density on file (std.density.polymer, an unfilled nylon) with its aluminium heat shield.","via":"harvest"}}]},"heat_shield_thickness":{"label":"Its aluminium heat shield's thickness","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the shield shows only through the lower half's slots and vents, never in section.","via":"harvest"}}]},"front_wall_x":{"label":"Its front wall (the inner face the front flange stands from), from its rear end","kind":"length","measurements":[{"id":"derived","value":6,"unit":"in","pm":0.15,"source":{"type":"derived","expr":"{.mounting_length} - {.front_flange_length} - {.wall}","via":"harvest"}}],"note":"Ahead of the wall the shell runs on open to its front face, over the cap and the front sight base's rear."}}},{"subject":"bcm-pmcr-mid","title":"BCM® PMCR (Polymer M-LOK® Compatible Rail)* Mid Length-BLACK (BCM-PMCR-MID-BLK)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"bcm","value":5.8,"unit":"oz","stated":"Natural ergonomics; slim, comfortable and lightweight, only 5.8 ounces","source":{"type":"spec","publisher":"manufacturer","name":"BCM, BCM® PMCR (Polymer M-LOK® Compatible Rail)* Mid Length-BLACK","url":"https://bravocompanyusa.com/bcm-pmcr-polymer-m-lok-rail-mid-length-black/","retrieved":"2026-10-28","via":"harvest"}},{"id":"primary-arms","value":5.8,"unit":"oz","stated":"Weight 5.8 oz.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Bravo Company Manufacturing PMCR Drop In AR-15 Handguard - M-LOK - Mid-Length (BCM-PMCR-MID-BLK)","url":"https://www.primaryarms.com/bravo-company-manufacturing-bcmgunfighter-pmcr-polymer-m-lok-compatible-rail-mid-length","retrieved":"2026-10-28","via":"harvest"}}],"adopt":{"from":"bcm","reason":"The maker's figure; Primary Arms' page states the same."},"note":"The two halves, the lower one with its aluminium heat shield. The discovery's reader reported \"4.48 oz\" in the page's data as well: the harvested copy has no such figure (its product record says \"weight\":null), and 4.48 ounces is what BCM's carbine-length page says of the carbine (bcm-pmcr-carbine.weight)."},"length":{"label":"Length, overall","kind":"length","measurements":[{"id":"photo","value":9.28,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 0ff6a5264742 (BCM's gallery photo STKL8992 of the black PMCR mid-length, assembled, its left side seen level, 4268 x 2846)","scaleRef":"its four upper M-LOK slots, centres 700.4 px apart (697 to 705) for the standard's 40 mm (std.mlok.slot_pitch): 444.7 px/in","method":"the outline (luminance under 200) from its rear end (column 4189, the upper rear flange's end) to its front face (column 62): 4127 px; ± 0.5% for the slots' scatter and the depth between the slots' faces and the outline's edges","via":"harvest"}}],"note":"BCM states no length. From its rear end, which bears on the delta ring's lip, to its front face, which stands ahead of the front sight base's rear face (the front hook and the upper half's front chamfer included)."},"width":{"label":"Width (the upper half, across its sides)","kind":"length","measurements":[{"id":"photo","value":1.873,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 530bce1646cf (BCM's gallery photo STKL8993: the two halves apart, the upper one from above, 1280 x 853)","scaleRef":"the upper half's own two rows of four M-LOK slots, centres 216.1 px apart for the standard's 40 mm: 137.2 px/in","method":"the upper half's silhouette across it at column 1019 (rows 505 to 762): 257 px; ± 4 px","via":"harvest"}},{"id":"carbine-photo","value":1.854,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-pmcr-carbine 291dadf219c1 (BCM's gallery photo STKL8997: the carbine-length's two halves apart, the upper one from above, 1280 x 853)","scaleRef":"its own rows of three M-LOK slots, 278.6 px apart: 176.9 px/in","method":"the upper half across it at column 600 (rows 462 to 790): 328 px; ± 4 px: the carbine-length's, the same section by every photo of the two","via":"harvest"}}],"adopt":{"from":"photo","reason":"The mid-length's own photo; the carbine-length's, the same section, agrees within the two ±."}},"lower_width":{"label":"The lower half's width (it stands inside the upper one's sides at the seam)","kind":"length","measurements":[{"id":"photo","value":1.717,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 530bce1646cf (BCM's gallery photo STKL8993: the two halves apart, the lower one from below, 1280 x 853)","scaleRef":"the lower half's own row of four M-LOK slots, 212.75 px apart for the standard's 40 mm: 135.1 px/in","method":"the lower half's silhouette across it at column 600 (rows 114 to 346): 232 px; ± 4 px","via":"harvest"}}]},"height":{"label":"Height, excluding the front hook","kind":"length","measurements":[{"id":"photo","value":2.172,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 0ff6a5264742 (BCM's gallery photo STKL8992 of the black PMCR mid-length, assembled, its left side seen level, 4268 x 2846)","scaleRef":"its four upper M-LOK slots, centres 700.4 px apart (697 to 705) for the standard's 40 mm (std.mlok.slot_pitch): 444.7 px/in","method":"the outline's top (row 976, the spine's pads) to the body's bottom (row 1942) at column 2400, clear of the hook: 966 px; ± 3 px","via":"harvest"}}],"note":"BCM gives no height."},"top_above_axis":{"label":"Its top (the spine's tab at its rear end, the outline's highest point) above the bore axis","kind":"length","measurements":[{"id":"photo","value":1.259,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 0ff6a5264742 (BCM's gallery photo STKL8992 of the black PMCR mid-length, assembled, its left side seen level, 4268 x 2846)","scaleRef":"its four upper M-LOK slots, centres 700.4 px apart (697 to 705) for the standard's 40 mm (std.mlok.slot_pitch): 444.7 px/in","method":"the bore axis at row 1532, the middle of its rear flanges (rows 1184 and 1880 at column 4140), which stand in the delta ring round the barrel nut; the outline's highest point, the spine's tab over the ring (row 972 at luminance 200, columns 4150 to 4170): 560 px; ± 6 px. The spine's pads along its length stand at rows 976 to 980, 0.01 lower","via":"harvest"}}]},"bottom_below_axis":{"label":"Its body's bottom (clear of the hook) below the bore axis","kind":"length","measurements":[{"id":"photo","value":0.922,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 0ff6a5264742 (BCM's gallery photo STKL8992 of the black PMCR mid-length, assembled, its left side seen level, 4268 x 2846)","scaleRef":"its four upper M-LOK slots, centres 700.4 px apart (697 to 705) for the standard's 40 mm (std.mlok.slot_pitch): 444.7 px/in","method":"the axis (row 1532) to the body's bottom (row 1942) at columns 1000 to 3800: 410 px; ± 6 px","via":"harvest"}}],"note":"The body stands higher than it hangs: 1.25 above the axis and 0.92 below, the spine over the gas tube."},"inside_diameter":{"label":"Inside diameter","kind":"length","measurements":[],"note":"BCM gives none, and no photo looks into an end. The model's inside is its outside less the wall (wall), which no view gives either."},"rear_x":{"label":"Its rear end (bearing on the delta ring's lip) ahead of the receiver's front face","kind":"length","measurements":[{"id":"derived","value":0.336,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{std.ar15.slip_ring_front_x}","via":"harvest"}}],"note":"Where the standard's delta ring holds it (std.ar15.slip_ring_front_x, from the Army's drawings): its rear flanges in the ring, against the lip. BCM's instructions (the carbine's page, its picture of them, e0a7762984ab): \"pull the Delta Ring to the furthest rearward position, enough to allow the rear of the PMCR to interface with the Barrel Nut teeth. The upper handguard will surround and index to the barrel nut enough to let the Delta Ring travel forward to secure the upper handguard in place\"."},"body_rear_x":{"label":"Its body's rear face (behind which its rear flanges and the spine's tab stand), from its rear end","kind":"length","measurements":[{"id":"photo","value":0.193,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 0ff6a5264742 (BCM's gallery photo STKL8992 of the black PMCR mid-length, assembled, its left side seen level, 4268 x 2846)","scaleRef":"its four upper M-LOK slots, centres 700.4 px apart (697 to 705) for the standard's 40 mm (std.mlok.slot_pitch): 444.7 px/in","method":"the body's rear face between the spine's tab and the upper flange (column 4103, rows 1100 to 1170) to the rear end (4189): 86 px; ± 3 px","via":"harvest"}}]},"rear_collar_od":{"label":"Its rear flanges (what stands in the delta ring round the barrel nut), outside diameter","kind":"length","measurements":[{"id":"photo","value":1.6,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 0ff6a5264742 (BCM's gallery photo STKL8992 of the black PMCR mid-length, assembled, its left side seen level, 4268 x 2846)","scaleRef":"its four upper M-LOK slots, centres 700.4 px apart (697 to 705) for the standard's 40 mm (std.mlok.slot_pitch): 444.7 px/in","method":"the upper flange's top (row 1178) to the lower flange's bottom (row 1890) where each is widest, columns 4120 to 4150: 712 px; ± 8 px for their rounded rear edges (at column 4140, 1184 to 1880, 1.565). The lower half seen from below (530bce1646cf) has its flange about 225 px across at 135.1 px/in, 1.66: its edges there are its rounds, not read square","via":"harvest"}}],"note":"Inside the delta ring's bore (std.ar15.slip_ring_bore_d, 1.75), and no larger than the barrel nut's toothed flange (std.ar15.barrel_nut_flange_od, 1.56) and a wall: BCM's instructions have the rear of the PMCR \"interface with the Barrel Nut teeth\" and the upper \"surround and index to the barrel nut\", so its flanges stand round the teeth and in their notches, which the nut's model has as a ring; what the two share there is said in the part."},"rear_collar_gap":{"label":"The gap between its two halves' rear flanges at each side (where the backdrop shows through)","kind":"length","measurements":[{"id":"photo","value":0.414,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 0ff6a5264742 (BCM's gallery photo STKL8992 of the black PMCR mid-length, assembled, its left side seen level, 4268 x 2846)","scaleRef":"its four upper M-LOK slots, centres 700.4 px apart (697 to 705) for the standard's 40 mm (std.mlok.slot_pitch): 444.7 px/in","method":"the backdrop through the rear end at column 4140: rows 1488 to 1672 (luminance over 240), 184 px; ± 3 px","via":"harvest"}}]},"rear_collar_gap_y":{"label":"That gap's middle above the bore axis (negative below)","kind":"length","measurements":[{"id":"photo","value":-0.108,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 0ff6a5264742 (BCM's gallery photo STKL8992 of the black PMCR mid-length, assembled, its left side seen level, 4268 x 2846)","scaleRef":"its four upper M-LOK slots, centres 700.4 px apart (697 to 705) for the standard's 40 mm (std.mlok.slot_pitch): 444.7 px/in","method":"the gap's middle (row 1580) less the axis (row 1532): 48 px under it; ± 3 px","via":"harvest"}}]},"seam_y":{"label":"The seam between its two halves, on the sides, above the bore axis (negative below)","kind":"length","measurements":[{"id":"photo","value":-0.378,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 0ff6a5264742 (BCM's gallery photo STKL8992 of the black PMCR mid-length, assembled, its left side seen level, 4268 x 2846)","scaleRef":"its four upper M-LOK slots, centres 700.4 px apart (697 to 705) for the standard's 40 mm (std.mlok.slot_pitch): 444.7 px/in","method":"the dark band where the upper half's side ends over the lower half (rows 1680 to 1720 at column 2400), its middle: 168 px under the axis; ± 10 px","via":"harvest"}}],"note":"The upper half reaches below the axis; the lower one, narrower (lower_width), stands inside its sides along the seam."},"side_top_y":{"label":"Where the upper half's upright side meets its M-LOK face, above the bore axis","kind":"length","measurements":[{"id":"photo","value":0.495,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 0ff6a5264742 (BCM's gallery photo STKL8992 of the black PMCR mid-length, assembled, its left side seen level, 4268 x 2846)","scaleRef":"its four upper M-LOK slots, centres 700.4 px apart (697 to 705) for the standard's 40 mm (std.mlok.slot_pitch): 444.7 px/in","method":"the change from the face's lit band to the side's textured one at column 2400 (row 1312): 220 px over the axis; ± 6 px","via":"harvest"}}]},"mlok_side_slots":{"label":"M-LOK slots in each upper face (the 10:30 and 1:30 rows)","kind":"count","measurements":[{"id":"bcm","value":4,"unit":"count","stated":"Three, four-hole M-LOK® compatible mounting slots, mounting surfaces (10:30, 1:30, and 6:00 o'clock placements)","source":{"type":"spec","publisher":"manufacturer","name":"BCM, BCM® PMCR (Polymer M-LOK® Compatible Rail)* Mid Length-BLACK","url":"https://bravocompanyusa.com/bcm-pmcr-polymer-m-lok-rail-mid-length-black/","retrieved":"2026-10-28","via":"harvest"}},{"id":"photo","value":4,"unit":"count","source":{"type":"photo","photo":"references/bcm-pmcr-mid 0ff6a5264742 (BCM's gallery photo STKL8992 of the black PMCR mid-length, assembled, its left side seen level, 4268 x 2846)","scaleRef":"none: a count","method":"four see-through slots in the left upper row; four in the right's on e565a88f6c43, and in both upper rows and the lower row on 530bce1646cf","via":"harvest"}}],"adopt":{"from":"bcm","reason":"BCM's \"four-hole\" for each of the three, counted on its three photos."}},"mlok_side_slot0_x":{"label":"The upper rows' rearmost M-LOK slot (its centre), from its rear end","kind":"length","measurements":[{"id":"photo","value":2.78,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 0ff6a5264742 (BCM's gallery photo STKL8992 of the black PMCR mid-length, assembled, its left side seen level, 4268 x 2846)","scaleRef":"its four upper M-LOK slots, centres 700.4 px apart (697 to 705) for the standard's 40 mm (std.mlok.slot_pitch): 444.7 px/in","method":"the rearmost slot's centre (column 2952.8, the see-through region's middle) from the rear end (4189): 1236 px; ± 3 px. The next three at 2253.1, 1556.3 and 851.7: the standard's pitch to half a percent","via":"harvest"}}]},"mlok_side_slot_y":{"label":"The upper rows' slot centres above the bore axis","kind":"length","measurements":[{"id":"photo","value":0.78,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 0ff6a5264742 (BCM's gallery photo STKL8992 of the black PMCR mid-length, assembled, its left side seen level, 4268 x 2846)","scaleRef":"its four upper M-LOK slots, centres 700.4 px apart (697 to 705) for the standard's 40 mm (std.mlok.slot_pitch): 444.7 px/in","method":"the slot's near rim, rows 1148 to 1222 at column 2400 (its upper wall's shadow over the see-through part): centre 1185, 347 px over the axis; ± 6 px","via":"harvest"}}]},"mlok_side_slot_z":{"label":"The upper rows' see-through slits, seen from above, out from the middle (to each side)","kind":"length","measurements":[{"id":"photo","value":0.543,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 530bce1646cf (BCM's gallery photo STKL8993: the two halves apart, the upper one from above, 1280 x 853)","scaleRef":"the upper half's own two rows of four M-LOK slots, centres 216.1 px apart for the standard's 40 mm: 137.2 px/in","method":"the two rows' see-through slits, centres at rows 561 and 710 at columns 401 to 1050: 74.5 px each side of their middle; ± 2 px","via":"harvest"}}],"note":"Not the slots' centres: from above, the upper half's own side under each face hides the outer part of what shows through a slot, so the slit stands inward of the slot. Not used by the model (mlok_side_face_distance is the face's place); kept as the reading it is."},"mlok_side_face_angle":{"label":"The upper M-LOK faces' outward direction about the bore axis, from straight up (degrees)","kind":"angle","measurements":[{"id":"bcm","value":45,"unit":"deg","stated":"Three, four-hole M-LOK® compatible mounting slots, mounting surfaces (10:30, 1:30, and 6:00 o'clock placements)","source":{"type":"spec","publisher":"manufacturer","name":"BCM, BCM® PMCR (Polymer M-LOK® Compatible Rail)* Mid Length-BLACK","url":"https://bravocompanyusa.com/bcm-pmcr-polymer-m-lok-rail-mid-length-black/","retrieved":"2026-10-28","via":"harvest"}},{"id":"photo","value":42,"unit":"deg","pm":5,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 0ff6a5264742 (BCM's gallery photo STKL8992 of the black PMCR mid-length, assembled, its left side seen level, 4268 x 2846)","scaleRef":"its four upper M-LOK slots, centres 700.4 px apart (697 to 705) for the standard's 40 mm (std.mlok.slot_pitch): 444.7 px/in","method":"the face runs from where the upright side ends (side_top_y, 0.495 up, at the half width, width / 2) to where it meets the spine (spine_vent_y, 1.084 up, at the spine's half width, spine_half_width): 0.589 up over 0.656 in, its outward direction 41.9° from up. The slot's near rim, 74 px tall in the level side view (rows 1148 to 1222), is the standard's 7 mm (std.mlok.slot_width) times the sine of 37°: the ±","via":"harvest"}}],"adopt":{"from":"photo","reason":"BCM's \"10:30, 1:30\" says which faces; the photo's own edges put them at 42 degrees from up, within its ± of BCM's 45. The accessories stand out at the angle the faces have."}},"mlok_side_face_distance":{"label":"The upper M-LOK faces' distance from the bore axis (along their outward direction)","kind":"length","measurements":[{"id":"derived","value":0.993,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.width} / 2 * sin({.mlok_side_face_angle}) + {.side_top_y} * cos({.mlok_side_face_angle})","via":"harvest"}}],"note":"The plane through the face's lower edge (the upright side's top at the half width) at the faces' angle: it meets the spine at spine_vent_y, and the slots' centres, which the level photo has 0.780 up, stand 0.04 up the face from where its normal through the axis meets it (where an accessory is placed)."},"mlok_bottom_slots":{"label":"M-LOK slots in the underside (six o'clock)","kind":"count","measurements":[{"id":"bcm","value":4,"unit":"count","stated":"Three, four-hole M-LOK® compatible mounting slots, mounting surfaces (10:30, 1:30, and 6:00 o'clock placements)","source":{"type":"spec","publisher":"manufacturer","name":"BCM, BCM® PMCR (Polymer M-LOK® Compatible Rail)* Mid Length-BLACK","url":"https://bravocompanyusa.com/bcm-pmcr-polymer-m-lok-rail-mid-length-black/","retrieved":"2026-10-28","via":"harvest"}},{"id":"photo","value":4,"unit":"count","source":{"type":"photo","photo":"references/bcm-pmcr-mid 530bce1646cf (BCM's gallery photo STKL8993: the two halves apart, the lower one from below, 1280 x 853)","scaleRef":"none: a count","method":"four slots along the lower half's middle, the heat shield bright through them"}}],"adopt":{"from":"bcm","reason":"BCM's figure, counted on its photo."}},"mlok_bottom_slot0_x":{"label":"The underside's rearmost M-LOK slot (its centre), from its rear end","kind":"length","measurements":[{"id":"photo","value":2.15,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 530bce1646cf (BCM's gallery photo STKL8993: the two halves apart, the lower one from below, 1280 x 853)","scaleRef":"its own row of four M-LOK slots, 212.75 px apart: 135.1 px/in","method":"the slots' see-through middles along row 225 at columns 523.5, 739 and 949 (the rearmost is broken by the shield behind it: one pitch behind the second, 310.8) less the lower half's rear end (column 20): 290.8 px; ± 0.06 in for the lower half's rear end, whose flange stops 0.03 in short of the upper's in the side view"}}]},"mlok_bottom_face_distance":{"label":"The underside's M-LOK face, its distance below the bore axis","kind":"length","measurements":[{"id":"derived","value":0.922,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{.bottom_below_axis}","via":"harvest"}}]},"reach_inside":{"label":"The room inside its M-LOK faces before what runs through it (how far an accessory's nuts may reach in)","kind":"length","measurements":[],"note":"Depends on the barrel, the gas tube and the heat shield, and on the wall, which no view gives: no figure, so the check reads as unmade."},"bottom_half_width":{"label":"Its underside's flat (where the six o'clock slots are), half its width","kind":"length","measurements":[{"id":"assumed","value":0.3,"unit":"in","pm":0.08,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the lower half from below (530bce1646cf) shows its slot row between its two rows of vents on faces turned down and out; the flat is taken as the slot's 7 mm and a margin each side as wide as the webs between the vents and the slots.","via":"harvest"}}]},"vent_count":{"label":"The vents along each lower side (through to the heat shield)","kind":"count","measurements":[{"id":"photo","value":7,"unit":"count","source":{"type":"photo","photo":"references/bcm-pmcr-mid 0ff6a5264742 (BCM's gallery photo STKL8992 of the black PMCR mid-length, assembled, its left side seen level, 4268 x 2846)","scaleRef":"none: a count","method":"seven dark runs along row 1905; seven in each row either side of the six o'clock slots on 530bce1646cf, the shield bright through them","via":"harvest"}}]},"vent0_x":{"label":"The rearmost lower vent's middle, from its rear end","kind":"length","measurements":[{"id":"photo","value":1.376,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 0ff6a5264742 (BCM's gallery photo STKL8992 of the black PMCR mid-length, assembled, its left side seen level, 4268 x 2846)","scaleRef":"its four upper M-LOK slots, centres 700.4 px apart (697 to 705) for the standard's 40 mm (std.mlok.slot_pitch): 444.7 px/in","method":"dark runs along row 1905 (luminance under 45), centres 3577, 3122.5, 2670.5, 2219.5, 1768.5, 1316.5, 862: the rearmost 612 px ahead of the rear end; ± 3 px","via":"harvest"}}]},"vent_pitch":{"label":"The lower vents, middle to middle","kind":"length","measurements":[{"id":"photo","value":1.0175,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 0ff6a5264742 (BCM's gallery photo STKL8992 of the black PMCR mid-length, assembled, its left side seen level, 4268 x 2846)","scaleRef":"its four upper M-LOK slots, centres 700.4 px apart (697 to 705) for the standard's 40 mm (std.mlok.slot_pitch): 444.7 px/in","method":"the first to the last, 2715 px over six gaps: 452.5 px each","via":"harvest"}}]},"vent_length":{"label":"Each lower vent's length along it","kind":"length","measurements":[{"id":"photo","value":0.607,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 0ff6a5264742 (BCM's gallery photo STKL8992 of the black PMCR mid-length, assembled, its left side seen level, 4268 x 2846)","scaleRef":"its four upper M-LOK slots, centres 700.4 px apart (697 to 705) for the standard's 40 mm (std.mlok.slot_pitch): 444.7 px/in","method":"the dark runs along row 1905: 270 to 273 px","via":"harvest"}}]},"vent_y":{"label":"The lower vents' middles above the bore axis (negative below)","kind":"length","measurements":[{"id":"photo","value":-0.843,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 0ff6a5264742 (BCM's gallery photo STKL8992 of the black PMCR mid-length, assembled, its left side seen level, 4268 x 2846)","scaleRef":"its four upper M-LOK slots, centres 700.4 px apart (697 to 705) for the standard's 40 mm (std.mlok.slot_pitch): 444.7 px/in","method":"the dark runs between rows 1880 and 1935 at columns 862 to 3577: middle 1907, 375 px under the axis; ± 8 px","via":"harvest"}}]},"vent_z":{"label":"The lower vents' middles out from the middle (to each side)","kind":"length","measurements":[{"id":"photo","value":0.418,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 530bce1646cf (BCM's gallery photo STKL8993: the two halves apart, the lower one from below, 1280 x 853)","scaleRef":"its own row of four M-LOK slots: 135.1 px/in","method":"the two rows of vents, middles at rows 167 and 280: 56.5 px each side of the slots' row; ± 3 px"}}]},"vent_width":{"label":"Each lower vent's width across it","kind":"length","measurements":[{"id":"photo","value":0.12,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 530bce1646cf (BCM's gallery photo STKL8993: the two halves apart, the lower one from below, 1280 x 853)","scaleRef":"its own row of four M-LOK slots: 135.1 px/in","method":"a vent's dark band across column 600 (rows 148 to 164): 16 px; ± 2 px, on a face turned partly away from the lens"}}]},"spine_half_width":{"label":"The spine along its top (the outer edges of its two rows of pockets), half its width","kind":"length","measurements":[{"id":"photo","value":0.272,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 530bce1646cf (BCM's gallery photo STKL8993: the two halves apart, the upper one from above, 1280 x 853)","scaleRef":"the upper half's own two rows of four M-LOK slots, centres 216.1 px apart for the standard's 40 mm: 137.2 px/in","method":"the two rows of pockets along the top, their outer edges at rows 598.7 and 673.3 (on a crop at 1.5 times): 37.3 px each side of their middle; ± 3 px","via":"harvest"}}]},"spine_vent_y":{"label":"The bottom of the spine (where the M-LOK faces meet it), above the bore axis","kind":"length","measurements":[{"id":"photo","value":1.084,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 0ff6a5264742 (BCM's gallery photo STKL8992 of the black PMCR mid-length, assembled, its left side seen level, 4268 x 2846)","scaleRef":"its four upper M-LOK slots, centres 700.4 px apart (697 to 705) for the standard's 40 mm (std.mlok.slot_pitch): 444.7 px/in","method":"the spine's pockets' lower edge and the face's lit band's top at column 2400 (row 1050): 482 px over the axis; ± 4 px","via":"harvest"}}]},"spine_groove_count":{"label":"The ribs across the spine (between its pockets, and at its ends)","kind":"count","measurements":[{"id":"photo","value":18,"unit":"count","source":{"type":"photo","photo":"references/bcm-pmcr-mid 530bce1646cf (BCM's gallery photo STKL8993: the two halves apart, the upper one from above, 1280 x 853)","scaleRef":"none: a count","method":"eighteen dark lines across the two rows of pockets along row 603 (columns 40 to 1212), the shadows of the ribs between them: seventeen pockets a row","via":"harvest"}}]},"spine_groove0_x":{"label":"The rearmost rib across the spine (its rear wall's shadow line), from its rear end","kind":"length","measurements":[{"id":"photo","value":0.146,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 530bce1646cf (BCM's gallery photo STKL8993: the two halves apart, the upper one from above, 1280 x 853)","scaleRef":"the upper half's own two rows of four M-LOK slots, centres 216.1 px apart for the standard's 40 mm: 137.2 px/in","method":"the first dark line along row 603 (column 40) less the rear end (20): 20 px; ± 2 px","via":"harvest"}}]},"spine_groove_pitch":{"label":"The ribs across the spine, middle to middle","kind":"length","measurements":[{"id":"photo","value":0.5025,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 530bce1646cf (BCM's gallery photo STKL8993: the two halves apart, the upper one from above, 1280 x 853)","scaleRef":"the upper half's own two rows of four M-LOK slots, centres 216.1 px apart for the standard's 40 mm: 137.2 px/in","method":"the first to the last line, columns 40 to 1212: 1172 px over seventeen gaps, 68.94 px each","via":"harvest"}}],"note":"Half the spine's vents' pitch on the side view (spine_vent_pitch, 1.014): the two photos agree within 1%."},"spine_centre_rib":{"label":"The rib along the spine's middle, between its two rows of pockets: its width","kind":"length","measurements":[{"id":"photo","value":0.267,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 530bce1646cf (BCM's gallery photo STKL8993: the two halves apart, the upper one from above, 1280 x 853)","scaleRef":"the upper half's own two rows of four M-LOK slots: 137.2 px/in","method":"between the pockets' inner edges, rows 616.7 and 653.3 (on a crop at 1.5 times): 36.7 px; ± 3 px","via":"harvest"}}]},"spine_pocket_rib":{"label":"The ribs across the spine between its pockets (along it), their width","kind":"length","measurements":[{"id":"photo","value":0.15,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 530bce1646cf (BCM's gallery photo STKL8993: the two halves apart, the upper one from above, 1280 x 853)","scaleRef":"the upper half's own two rows of four M-LOK slots: 137.2 px/in","method":"the lit ribs between the pockets, about 20 px along (30 on the crop at 1.5 times), each with a dark line of its wall's shadow at its rear; ± 4 px, by eye","via":"harvest"}}],"note":"The pockets lie between the ribs, centred between the lines spine_groove0_x and spine_groove_pitch place: as long as the pitch less a rib."},"spine_rim":{"label":"The rim along the spine's outer top edge, over its pockets","kind":"length","measurements":[{"id":"assumed","value":0.04,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the level side view's top edge runs straight over the pockets (no notch where each is), so a rim stands along the top over them; from above it is a thin lit edge outside each pocket, 2 px on the mid-length's photo (0.015 in) and 8 px on the carbine-length's (0.045).","via":"harvest"}}]},"spine_slit_width":{"label":"The slit through the floor of every other pocket (by the middle rib), its width","kind":"length","measurements":[{"id":"photo","value":0.03,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 530bce1646cf (BCM's gallery photo STKL8993: the two halves apart, the upper one from above, 1280 x 853)","scaleRef":"the upper half's own two rows of four M-LOK slots: 137.2 px/in","method":"the backdrop seen through under the first three pockets' inner edges, rows 615 to 618 and 612 to 615: 4 px; ± 1 px","via":"harvest"}}]},"spine_vent_count":{"label":"The windows in each side of the spine, into every other pocket","kind":"count","measurements":[{"id":"photo","value":8,"unit":"count","source":{"type":"photo","photo":"references/bcm-pmcr-mid 0ff6a5264742 (BCM's gallery photo STKL8992 of the black PMCR mid-length, assembled, its left side seen level, 4268 x 2846)","scaleRef":"none: a count","method":"eight dark pockets along row 1025, each under a pad; the see-through slits under alternate pads from above (530bce1646cf) agree","via":"harvest"}}]},"spine_vent0_x":{"label":"The rearmost spine vent's middle, from its rear end","kind":"length","measurements":[{"id":"photo","value":0.858,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 0ff6a5264742 (BCM's gallery photo STKL8992 of the black PMCR mid-length, assembled, its left side seen level, 4268 x 2846)","scaleRef":"its four upper M-LOK slots, centres 700.4 px apart (697 to 705) for the standard's 40 mm (std.mlok.slot_pitch): 444.7 px/in","method":"the dark pockets along row 1025 (luminance under 45), centres 3807.5, 3354, 2902.5, 2452, 2002.5, 1555, 1104.5, 651: the rearmost 381.5 px ahead of the rear end. From above, the slits under the first three pads at 0.89, 1.91 and 2.88","via":"harvest"}}]},"spine_vent_pitch":{"label":"The spine's vents, middle to middle","kind":"length","measurements":[{"id":"photo","value":1.014,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 0ff6a5264742 (BCM's gallery photo STKL8992 of the black PMCR mid-length, assembled, its left side seen level, 4268 x 2846)","scaleRef":"its four upper M-LOK slots, centres 700.4 px apart (697 to 705) for the standard's 40 mm (std.mlok.slot_pitch): 444.7 px/in","method":"the first to the last, 3156.5 px over seven gaps: 450.9 px each","via":"harvest"}}]},"spine_vent_length":{"label":"Each spine vent's length along it","kind":"length","measurements":[{"id":"photo","value":0.4,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 0ff6a5264742 (BCM's gallery photo STKL8992 of the black PMCR mid-length, assembled, its left side seen level, 4268 x 2846)","scaleRef":"its four upper M-LOK slots, centres 700.4 px apart (697 to 705) for the standard's 40 mm (std.mlok.slot_pitch): 444.7 px/in","method":"the dark pockets along row 1025: 174 to 181 px","via":"harvest"}}]},"spine_vent_height":{"label":"Each spine vent's height (from the spine's bottom up)","kind":"length","measurements":[{"id":"photo","value":0.103,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 0ff6a5264742 (BCM's gallery photo STKL8992 of the black PMCR mid-length, assembled, its left side seen level, 4268 x 2846)","scaleRef":"its four upper M-LOK slots, centres 700.4 px apart (697 to 705) for the standard's 40 mm (std.mlok.slot_pitch): 444.7 px/in","method":"the dark pocket at column 2400, rows 1004 to 1050: 46 px","via":"harvest"}}]},"front_notch_x":{"label":"The opening across the top of its front end (round the front sight base's tower): its back, from its rear end","kind":"length","measurements":[{"id":"photo","value":8.863,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 530bce1646cf (BCM's gallery photo STKL8993: the two halves apart, the upper one from above, 1280 x 853)","scaleRef":"the upper half's own two rows of four M-LOK slots, centres 216.1 px apart for the standard's 40 mm: 137.2 px/in","method":"along the spine's middle (row 635) the polymer ends at column 1236, the rear end at column 20: 1216 px; ± 3 px. The backdrop shows from there to the faces' front tip seen from above (column 1264, 9.067 in from the rear end), which stands behind the side view's front face (length) by the front's chamfer","via":"harvest"}}]},"front_notch_half_width":{"label":"That opening's half width, at its back","kind":"length","measurements":[{"id":"photo","value":0.48,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 530bce1646cf (BCM's gallery photo STKL8993: the two halves apart, the upper one from above, 1280 x 853)","scaleRef":"the upper half's own two rows of four M-LOK slots: 137.2 px/in","method":"across column 1240 (0.17 in from the front), the backdrop from row 567 to row 699: 66 px each side of the middle (633); it widens to 0.70 at column 1250; ± 6 px","via":"harvest"}}]},"panel_top_y":{"label":"The textured panels' top edge, above the bore axis","kind":"length","measurements":[{"id":"photo","value":0.47,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 0ff6a5264742 (BCM's gallery photo STKL8992 of the black PMCR mid-length, assembled, its left side seen level, 4268 x 2846)","scaleRef":"its four upper M-LOK slots, centres 700.4 px apart (697 to 705) for the standard's 40 mm (std.mlok.slot_pitch): 444.7 px/in","method":"the panels' upper edge along the side (row 1323): 209 px over the axis; ± 5 px","via":"harvest"}}]},"panel_bottom_y":{"label":"The textured panels' bottom edge, above the bore axis (negative below)","kind":"length","measurements":[{"id":"photo","value":-0.13,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 0ff6a5264742 (BCM's gallery photo STKL8992 of the black PMCR mid-length, assembled, its left side seen level, 4268 x 2846)","scaleRef":"its four upper M-LOK slots, centres 700.4 px apart (697 to 705) for the standard's 40 mm (std.mlok.slot_pitch): 444.7 px/in","method":"the panels' lower edge (row 1590): 58 px under the axis; ± 5 px","via":"harvest"}}]},"panel_rear_x":{"label":"The rearmost panel's rear end, from its rear end","kind":"length","measurements":[{"id":"photo","value":0.5,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/bcm-pmcr-mid e565a88f6c43 (BCM's main photo STKL8991, the mid-length assembled, its right side seen level, 1280 x 853)","scaleRef":"its four upper M-LOK slots, 210.9 px apart: 133.9 px/in","method":"the panel's rear end (column 85) less the rear end (18): 67 px; ± 6 px, by eye on the photo"}}]},"panel_dividers":{"label":"The ribs between the textured panels: how many","kind":"count","measurements":[{"id":"photo","value":3,"unit":"count","source":{"type":"photo","photo":"references/bcm-pmcr-mid e565a88f6c43 (BCM's main photo STKL8991, the mid-length assembled, its right side seen level, 1280 x 853)","scaleRef":"none: a count","method":"four panels along each side (the front one under the star), with a rib between each two; the same on the left side (0ff6a5264742)"}}]},"panel_divider_top_x":{"label":"The ribs between the panels: where each meets the panels' top edge, from its rear end (the first)","kind":"length","measurements":[{"id":"photo","value":5.09,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/bcm-pmcr-mid e565a88f6c43 (BCM's main photo STKL8991, the mid-length assembled, its right side seen level, 1280 x 853)","scaleRef":"its four upper M-LOK slots, 210.9 px apart: 133.9 px/in","method":"the first rib's top at column 700 less the rear end (18); the second's at 930 (6.81) and the third's at 1140 (8.38); ± 6 px, by eye. On the left side (0ff6a5264742) the first two at 5.08 and 6.80"}}],"note":"The three ribs' tops: 5.09, 6.81 and 8.38 (panel_divider1_top_x, panel_divider2_top_x)."},"panel_divider1_top_x":{"label":"The second rib's top, from its rear end","kind":"length","measurements":[{"id":"photo","value":6.81,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/bcm-pmcr-mid e565a88f6c43 (BCM's main photo STKL8991, the mid-length assembled, its right side seen level, 1280 x 853)","scaleRef":"its four upper M-LOK slots: 133.9 px/in","method":"column 930 less the rear end (18); ± 6 px, by eye","via":"harvest"}}]},"panel_divider2_top_x":{"label":"The third rib's top (the star panel's rear edge), from its rear end","kind":"length","measurements":[{"id":"photo","value":8.38,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/bcm-pmcr-mid e565a88f6c43 (BCM's main photo STKL8991, the mid-length assembled, its right side seen level, 1280 x 853)","scaleRef":"its four upper M-LOK slots: 133.9 px/in","method":"column 1140 less the rear end (18); ± 6 px, by eye","via":"harvest"}}]},"panel_divider_bottom_x":{"label":"The first rib's foot (where it meets the panels' bottom edge), from its rear end","kind":"length","measurements":[{"id":"photo","value":3.94,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/bcm-pmcr-mid e565a88f6c43 (BCM's main photo STKL8991, the mid-length assembled, its right side seen level, 1280 x 853)","scaleRef":"its four upper M-LOK slots: 133.9 px/in","method":"column 545 less the rear end (18); ± 6 px, by eye","via":"harvest"}}]},"panel_divider1_bottom_x":{"label":"The second rib's foot, from its rear end","kind":"length","measurements":[{"id":"photo","value":6.21,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/bcm-pmcr-mid e565a88f6c43 (BCM's main photo STKL8991, the mid-length assembled, its right side seen level, 1280 x 853)","scaleRef":"its four upper M-LOK slots: 133.9 px/in","method":"column 850 less the rear end (18); ± 6 px, by eye","via":"harvest"}}]},"panel_divider2_bottom_x":{"label":"The third rib's foot, from its rear end","kind":"length","measurements":[{"id":"photo","value":8.42,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/bcm-pmcr-mid e565a88f6c43 (BCM's main photo STKL8991, the mid-length assembled, its right side seen level, 1280 x 853)","scaleRef":"its four upper M-LOK slots: 133.9 px/in","method":"column 1145 less the rear end (18); ± 6 px, by eye","via":"harvest"}}]},"panel_rib":{"label":"The ribs between the panels, their width","kind":"length","measurements":[{"id":"photo","value":0.11,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-pmcr-mid e565a88f6c43 (BCM's main photo STKL8991, the mid-length assembled, its right side seen level, 1280 x 853)","scaleRef":"its four upper M-LOK slots: 133.9 px/in","method":"the smooth ribs between the stippled panels, about 15 px across; ± 4 px, by eye","via":"harvest"}}]},"panel_depth":{"label":"How far the textured panels stand in from the side round them","kind":"length","measurements":[{"id":"assumed","value":0.015,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: BCM's \"Aggressive textured area\" is a stipple whose edge catches the light round each panel in the photos; no view shows it in section. Drawn as a shallow recess, the stipple itself not drawn.","via":"harvest"}}]},"tab_x":{"label":"The ribbed tab on the lower half's rear (over the upper half's side): its rear end, from its rear end","kind":"length","measurements":[{"id":"photo","value":0.133,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 0ff6a5264742 (BCM's gallery photo STKL8992 of the black PMCR mid-length, assembled, its left side seen level, 4268 x 2846)","scaleRef":"its four upper M-LOK slots, centres 700.4 px apart (697 to 705) for the standard's 40 mm (std.mlok.slot_pitch): 444.7 px/in","method":"the tab's rear end at column 4130 (rows 1530 to 1680, ahead of the gap between the flanges) less the rear end (4189); ± 4 px","via":"harvest"}}]},"tab_front_x":{"label":"The ribbed tab's front end (at the seam), from its rear end","kind":"length","measurements":[{"id":"photo","value":1.06,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 0ff6a5264742 (BCM's gallery photo STKL8992 of the black PMCR mid-length, assembled, its left side seen level, 4268 x 2846)","scaleRef":"its four upper M-LOK slots, centres 700.4 px apart (697 to 705) for the standard's 40 mm (std.mlok.slot_pitch): 444.7 px/in","method":"the tab's lower front corner at column 3718: 471 px ahead of the rear end; ± 8 px","via":"harvest"}}]},"tab_top_y":{"label":"The ribbed tab's top (its rear part, level), above the bore axis","kind":"length","measurements":[{"id":"photo","value":0.005,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 0ff6a5264742 (BCM's gallery photo STKL8992 of the black PMCR mid-length, assembled, its left side seen level, 4268 x 2846)","scaleRef":"its four upper M-LOK slots, centres 700.4 px apart (697 to 705) for the standard's 40 mm (std.mlok.slot_pitch): 444.7 px/in","method":"its top edge at row 1530 from column 3880 to 4130, falling to row 1650 at column 3720; ± 6 px","via":"harvest"}}]},"tab_knee_x":{"label":"Where the ribbed tab's level top begins to fall toward its front, from its rear end","kind":"length","measurements":[{"id":"photo","value":0.695,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-pmcr-mid 0ff6a5264742 (BCM's gallery photo STKL8992 of the black PMCR mid-length, assembled, its left side seen level, 4268 x 2846)","scaleRef":"its four upper M-LOK slots, centres 700.4 px apart (697 to 705) for the standard's 40 mm (std.mlok.slot_pitch): 444.7 px/in","method":"its top edge level at row 1530 back from column 3880, falling ahead of it to row 1650 at column 3720: 309 px ahead of the rear end; ± 15 px, by eye on a crop","via":"harvest"}}]},"tab_proud":{"label":"How far the ribbed tab stands out from the upper half's side","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the tab shows its lit top edge over the upper half's side in the level side views; how far it stands out isn't seen from above or an end.","via":"harvest"}}]},"mounting_length":{"label":"Its length between the ring and the cap (from its rear end to its front flange's end)","kind":"length","measurements":[{"id":"assumed","value":8.45,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: BCM states none and no photo shows the front flange, inside its front end. Taken as from its rear end on the delta ring's lip (rear_x) to the triangular cap's floor on BCM's 16 in mid-length barrel with BCM's F base: the triangle cap's rim at 15.573 in the rifle and its floor 0.245 in ahead (bcm-handguard-cap-triangle-750: its length less its collar and sheet), less the ring's lip at 7.372 (std.ar15.upper_front_face_x + std.ar15.slip_ring_front_x).","via":"harvest"}}]},"front_flange_od":{"label":"Its front flange (what goes into the triangular cap), outside diameter","kind":"length","measurements":[{"id":"assumed","value":1.36,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the flange goes into the cap (BCM: \"will only fit the M16A1 'Triangular' front handguard retaining cap\") and shows on no photo. Drawn round, inside the triangular cap's sides, which stand 0.689 from the axis inside at their middles (bcm-handguard-cap-triangle-750: side_r less side_centre_r less the sheet): a flange that takes only the triangle's shape fills its corners, which isn't drawn.","via":"harvest"}}]},"front_flange_length":{"label":"Its front flange's length (into the cap)","kind":"length","measurements":[{"id":"assumed","value":0.4,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view shows the flange. Long enough that the front wall it stands from stays behind the triangular cap's rim with the flange home in its pocket (0.245 deep).","via":"harvest"}}]},"base_clearance":{"label":"How far its inside stands off the front sight base where the base stands in its front end","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no photo looks into its front end, and the real part goes on round a front sight base (BCM's instructions draw it so). The inside under the hood is cut clear of BCM's F base model (bcm-front-sight-base-f-750) as it stands with the hand guard seated in the triangular cap, this far off each of the base's faces.","via":"harvest"}}]},"wall":{"label":"Its polymer wall's thickness","kind":"length","measurements":[{"id":"assumed","value":0.1,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view shows an end square on or a section. Taken so that the model comes near BCM's 5.8 oz at the polymer's density on file (std.density.polymer, an unfilled nylon) with its aluminium heat shield.","via":"harvest"}}]},"heat_shield_thickness":{"label":"Its aluminium heat shield's thickness","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the shield shows only through the lower half's slots and vents, never in section.","via":"harvest"}}]},"front_wall_x":{"label":"Its front wall (the inner face the front flange stands from), from its rear end","kind":"length","measurements":[{"id":"derived","value":7.95,"unit":"in","pm":0.15,"source":{"type":"derived","expr":"{.mounting_length} - {.front_flange_length} - {.wall}","via":"harvest"}}],"note":"Ahead of the wall the shell runs on open to its front face, over the cap and the front sight base's rear."}}},{"subject":"bcm-pnt-trigger","title":"BCM PNT Trigger Assembly AR15 (BCM-PNT-TA1)","dimensions":{"weight":{"label":"Weight (the assembly)","kind":"mass","measurements":[],"note":"Not sourced: BCM states none (its page, its marketing site, its brochure; its shop's own product data has \"weight\":null). What sellers print is the parcel's: MidwayUSA \"shippingWeight\":0.266159 (\"0.266 Pounds\", 4.26 oz, in its page's data), AR15Discounts \"Weight 4 oz\" beside \"Dimensions 5.25 × 2 × 2 in\" (a box), KYGUNCO \"Weight 2 lb\" (the figure its other BCM pages carry). None is the part's, so none is entered: the build's weight says it is unknown. A reviewer's scale reading of the assembly, or of a mil-spec trigger group, would close it."},"pin_diameter":{"label":"Trigger and hammer pin diameter (small .154 or large .170)","kind":"length","measurements":[{"id":"tdp","value":0.15375,"unit":"in","pm":0.00025,"stated":"Ø.154-.0005","source":{"type":"standard","doc":"US Army TDP drawing 8448609 (Pin, Hammer & Trigger), rev H, scale 4/1: the end view; user-supplied scan (Distribution Statement F, Colt proprietary notice), PDF page 73 (references/bcm-pnt-trigger/tdp-8448609-p73.png, never committed)","via":"user"},"note":"The middle of .1535 to .1540. The same sheet: .900 long, two grooves (.030R X .125 DIA) at .130 and .450 from one end."},{"id":"alexanders","value":0.1565,"unit":"in","pm":0.0005,"stated":"Pin Size: .156\" / .157\" (small pin)","source":{"type":"spec","publisher":"retailer","name":"Alexander's Store, BCM PNT Trigger Assembly AR-15, Key Specifications (the store's own list)","url":"https://alexandersstore.com/product/bcm-pnt-trigger-assembly-ar15/","retrieved":"2026-10-05","via":"harvest"},"note":"The same page's prose: \"The .156/.157 pin holes are honed for tight alignment\" and \"uses standard small .156/.157 pins\". BCM's sentence, which it restates, is about the holes."}],"adopt":{"from":"tdp","reason":"A .156 pin doesn't pass a .156 hole: the store's figure is BCM's for the holes (\"156/157 holes are honed\"), given as the pin's. The pin a receiver built to the TDP takes is the Army drawing's, and BCM grinds its pins to fit those receivers."},"note":"BCM gives no diameter for the two pins the assembly comes with: \"This assembly includes our impact resistant trigger and hammer pins. They are centerless ground to a fine finish and superior tolerances to ensure compatibility with all MIL SPEC lower receivers built per the USGI TDP.\" The figure is the Army drawing's for the pin those receivers take (their holes .1560 +.0015, std.ar15.fcg_pin_hole_d); BCM's exploded line drawing shows both pins with that drawing's two grooves. BCM's own number is for the holes the pins pass through (pivot_hole_d), which one seller prints as the pin's."},"pivot_hole_d":{"label":"The trigger's pivot hole (the bore its pin passes through), diameter","kind":"length","measurements":[{"id":"bcm","value":0.1565,"unit":"in","pm":0.0005,"stated":"156/157 holes are honed to assist in perfect alignment and a smooth trigger pull.","source":{"type":"spec","publisher":"manufacturer","name":"Bravo Company USA, BCM® PNT Trigger Assembly AR15 (BCM-PNT-TA1), Description","url":"https://bravocompanyusa.com/bcm-pnt-trigger-assembly-ar15/","retrieved":"2026-10-05","via":"harvest"},"note":"BCM's shorthand for .156 to .157 in, of the trigger's and the hammer's holes (its marketing site: \"trigger and hammer bores are honed to perfection\")."},{"id":"tdp","value":0.157,"unit":"in","pm":0.001,"stated":".156 DIA+.002 THRU (BOTH SIDES)","source":{"type":"standard","doc":"US Army TDP drawing 8448592 (Trigger), rev L, scale 2/1, sheet 1 of 1; user-supplied scan (Distribution Statement F, Colt proprietary notice), PDF page 43 (references/aero-m4e1-lower 1dabf089edf8)","via":"user"},"note":"View E-E, datum -A-: .156 to .158 through both walls and bosses."}],"adopt":{"from":"bcm","reason":"The maker's own figure for this product. It lies inside the Army drawing's .156 to .158: the one dimension BCM states, and it is the drawing's."}},"rest_angle":{"label":"The trigger at rest: how far it is turned about its pin from the Army drawing's side elevation (positive turns the blade forward)","kind":"angle","measurements":[{"id":"aero","value":-1,"unit":"deg","source":{"type":"derived","expr":"{aero-m4e1-lower.trigger_rest_angle}","via":"harvest"}}],"note":"No picture of BCM's shows this trigger installed square to the side (its two are lifestyle photos, from above and from below). A trigger of the same drawing at rest in a mil-spec lower is on file: Aero's complete lower (its \"Mil-spec Lower Parts Kit\"), where the drawing's outline was fitted to the blade in Aero's pin-framed photo. The drawing's elevation has the tail level; no drawing on file shows the trigger against the hammer and disconnector."},"tail_at_rest_x":{"label":"The tail's end at rest, X in the trigger's frame (the pin's axis the origin)","kind":"length","measurements":[{"id":"derived","value":-1.2023,"unit":"in","source":{"type":"derived","expr":"-{std.ar15.trigger_tail_behind_pivot} * cos({.rest_angle})","via":"user"}}],"note":"Where the drawing's 1.210 -.015 tail end goes when the trigger is turned to rest: the second point of the frame the side elevation is traced in."},"tail_at_rest_y":{"label":"The tail's end at rest, Y in the trigger's frame","kind":"length","measurements":[{"id":"derived","value":0.021,"unit":"in","source":{"type":"derived","expr":"-{std.ar15.trigger_tail_behind_pivot} * sin({.rest_angle})","via":"user"}}]},"face_offset_x":{"label":"The blade's face ahead of the trigger pin, at rest (the deepest point of its curve)","kind":"length","measurements":[{"id":"drawing","value":0.05,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/aero-m4e1-lower 1dabf089edf8 (US Army TDP drawing 8448592 (Trigger) rev L (the user's M16 TDP scan, PDF page 43): the side elevation)","scaleRef":"frame from the reviewed holes pivot, tail (315.2 px/in, rms 0.000 in over 2 points)","method":"x_max in x [-0.05, 0.3] in y [-1.05, -0.99] of the traced outline (tools/trace.py); the blade's front edge where it is furthest back, 0.99 to 1.05 below the pin with the trigger at rest (the edge is within 0.001 of that from 0.9 to 1.05; the section line's crossing at 0.95 is left out); ± mostly the rest angle's 0.8° at an inch from the pin (0.014), and the drawing's stroke","via":"user"}}],"note":"Where a finger lies: the front edge's rearmost point, as length of pull is read on the Aero lower's trigger of the same drawing (aero-m4e1-lower.trigger_face_x, 1.964 on its photo against 1.978 by the drawing). The drawing's face is an arc (.62 R about a centre .69 ahead of and .97 below the pivot), which puts its deepest point .07 ahead of the pin before the turn to rest."},"shoe_face_x":{"label":"The blade's face ahead of the takedown pin on a mil-spec lower (derived)","kind":"length","measurements":[{"id":"derived","value":1.978,"unit":"in","source":{"type":"derived","expr":"{std.ar15.trigger_pin_x} + {.face_offset_x}","via":"user"}}],"note":"Length of pull is read from here."},"shoe_width":{"label":"The blade's width (Z)","kind":"length","measurements":[{"id":"tdp","value":0.29,"unit":"in","source":{"type":"derived","expr":"{std.ar15.trigger_body_width}","via":"user"}}],"note":"The blade is as wide as the body: the drawing's front view (unlabelled, over View E-E) and Section A-A draw it between the body's own lines from the bosses to its tip, and the body is .290 -B-. Sellers of mil-spec triggers measure the bow the same (RECOIL's guide: Stag's \"measured 0.29 inches wide\"; ALG \"Bow Width: 0.29\"\": quoted in larue-mbt-2s.shoe_width)."},"boss_length":{"label":"The bosses round the pivot hole, end to end (across the trigger)","kind":"length","measurements":[{"id":"tdp","value":0.68,"unit":"in","pm":0.003,"stated":".680±.003, symmetrical about -B- within .006 TOTAL","source":{"type":"standard","doc":"US Army TDP drawing 8448592 (Trigger), rev L, scale 2/1, sheet 1 of 1; user-supplied scan (Distribution Statement F, Colt proprietary notice), PDF page 43 (references/aero-m4e1-lower 1dabf089edf8)","via":"user"},"note":"The front view over View E-E (zone 2-D): the callout's extension lines stand on the two bosses' end faces, 214 px apart at the sheet's 315 px/in (0.679). The lower's pocket is .690 wide (std.ar15.fcg_pocket_width)."},{"id":"model","value":0.664,"unit":"in","source":{"type":"derived","expr":"{std.ar15.trigger_boss_length}","via":"user"},"note":"The CAD reference set's trigger (a third-party model), as the standard ledger records it."}],"adopt":{"from":"tdp","reason":"The drawing dimensions it; beside the TDP the drawing wins and the difference is said (D49): the third-party model's bosses are 0.016 short."},"note":"The standard ledger has only the reference model's figure here and says the drawing doesn't dimension it; it does, on the unlabelled front view over View E-E. Reported to the catalog's keeper for std.ar15.trigger_boss_length."},"boss_step_length":{"label":"The bosses' ends, how far in from each end their upper half is cut away","kind":"length","measurements":[{"id":"tdp","value":0.058,"unit":"in","pm":0.005,"stated":".058, 2 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 8448592 (Trigger), rev L, scale 2/1, sheet 1 of 1; user-supplied scan (Distribution Statement F, Colt proprietary notice), PDF page 43 (references/aero-m4e1-lower 1dabf089edf8)","via":"user"},"note":"The front view over View E-E: from each boss's end face to the upper half's (19 px, 0.060). The rear view has the same step (22 px)."}],"note":"Each boss's end is a half round: above a flat just over the pin's axis it stops short. The hammer spring's legs lie on the trigger pin there. Primary Arms' side photo shows it: the lower half ring standing proud round the pin, a line across just above the pin's middle; BCM's exploded drawing draws the same step."},"boss_step_above_axis":{"label":"The bosses' ends, the step's flat above the pivot's axis","kind":"length","measurements":[{"id":"tdp","value":0.03,"unit":"in","pm":0.01,"stated":".03, 2 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 8448592 (Trigger), rev L, scale 2/1, sheet 1 of 1; user-supplied scan (Distribution Statement F, Colt proprietary notice), PDF page 43 (references/aero-m4e1-lower 1dabf089edf8)","via":"user"},"note":"The front view over View E-E: from the pivot's centre line to the step's line. The rear view puts it 8 px (0.025) above the axis."}]},"boss_fillet_r":{"label":"The fillet where each boss meets the body's side, radius","kind":"length","measurements":[{"id":"tdp","value":0.055,"unit":"in","pm":0.015,"stated":".055 R±.015, 2 PLACES AROUND BOSSES","source":{"type":"standard","doc":"US Army TDP drawing 8448592 (Trigger), rev L, scale 2/1, sheet 1 of 1; user-supplied scan (Distribution Statement F, Colt proprietary notice), PDF page 43 (references/aero-m4e1-lower 1dabf089edf8)","via":"user"},"note":"Section B-B (through the pivot, looking down)."}]},"slot_width":{"label":"The disconnector's slot, width","kind":"length","measurements":[{"id":"tdp","value":0.1255,"unit":"in","pm":0.0035,"stated":".122+.007, symmetrical about -B- within .006 TOTAL","source":{"type":"standard","doc":"US Army TDP drawing 8448592 (Trigger), rev L, scale 2/1, sheet 1 of 1; user-supplied scan (Distribution Statement F, Colt proprietary notice), PDF page 43 (references/aero-m4e1-lower 1dabf089edf8)","via":"user"},"note":"The rear view: the middle of .122 to .129. Section A-A gives the same slot as .125 between two .082 walls (.082 + .125 + .082 = .289)."}]},"slot_floor_below_pivot":{"label":"The disconnector's slot, its floor below the pivot's axis","kind":"length","measurements":[{"id":"tdp","value":0.19,"unit":"in","pm":0.005,"stated":".190","source":{"type":"standard","doc":"US Army TDP drawing 8448592 (Trigger), rev L, scale 2/1, sheet 1 of 1; user-supplied scan (Distribution Statement F, Colt proprietary notice), PDF page 43 (references/aero-m4e1-lower 1dabf089edf8)","via":"user"},"note":"The side elevation, a section on the centre plane (the hatched strip is the floor): from the pivot's centre line down to the hatching's top, 60 px (0.190). The same chain: .058 ± .002 up to the tail's top, .230 to the spring hole's floor, .270 to the tail's underside."}]},"slot_front_ahead_of_pivot":{"label":"The disconnector's slot, where its floor runs out at the top ahead of the pivot","kind":"length","measurements":[{"id":"tdp","value":0.48,"unit":"in","pm":0.01,"stated":".48","source":{"type":"standard","doc":"US Army TDP drawing 8448592 (Trigger), rev L, scale 2/1, sheet 1 of 1; user-supplied scan (Distribution Statement F, Colt proprietary notice), PDF page 43 (references/aero-m4e1-lower 1dabf089edf8)","via":"user"},"note":"The side elevation: from the pivot's centre line to an extension line standing on the nose's top where the 1.00 R arc reaches it (149 px, 0.473). The top view's slot ends there (0.48)."}]},"slot_front_r":{"label":"The disconnector's slot, the radius its floor rises on to the top","kind":"length","measurements":[{"id":"tdp","value":1,"unit":"in","pm":0.01,"stated":"1.00 R","source":{"type":"standard","doc":"US Army TDP drawing 8448592 (Trigger), rev L, scale 2/1, sheet 1 of 1; user-supplied scan (Distribution Statement F, Colt proprietary notice), PDF page 43 (references/aero-m4e1-lower 1dabf089edf8)","via":"user"},"note":"The side elevation: the arc from the floor up through the nose's top, its centre mark .8 above the pivot (the cutter's path). Its lowest point scales 0.20 below the pivot, the floor's .190."}]},"spring_hole_d":{"label":"The disconnector spring's hole in the slot's floor, diameter","kind":"length","measurements":[{"id":"tdp","value":0.164,"unit":"in","pm":0.004,"stated":".164 DIA±.004 TO DEPTH SHOWN","source":{"type":"standard","doc":"US Army TDP drawing 8448592 (Trigger), rev L, scale 2/1, sheet 1 of 1; user-supplied scan (Distribution Statement F, Colt proprietary notice), PDF page 43 (references/aero-m4e1-lower 1dabf089edf8)","via":"user"},"note":"The top view; View C (scale 10/1) repeats it as .164 DIA REF."}]},"spring_hole_behind_pivot":{"label":"The disconnector spring's hole, its centre behind the pivot","kind":"length","measurements":[{"id":"tdp","value":0.614,"unit":"in","pm":0.005,"stated":".614","source":{"type":"standard","doc":"US Army TDP drawing 8448592 (Trigger), rev L, scale 2/1, sheet 1 of 1; user-supplied scan (Distribution Statement F, Colt proprietary notice), PDF page 43 (references/aero-m4e1-lower 1dabf089edf8)","via":"user"},"note":"The top view: from the pivot's axis back to the hole's centre."}]},"spring_hole_floor_below_pivot":{"label":"The disconnector spring's hole, its floor below the pivot's axis","kind":"length","measurements":[{"id":"tdp","value":0.23,"unit":"in","pm":0.005,"stated":".230 (side elevation); .230 REF (View C)","source":{"type":"standard","doc":"US Army TDP drawing 8448592 (Trigger), rev L, scale 2/1, sheet 1 of 1; user-supplied scan (Distribution Statement F, Colt proprietary notice), PDF page 43 (references/aero-m4e1-lower 1dabf089edf8)","via":"user"},"note":"From the pivot's centre line, on the same chain as the slot's floor (.190) and the tail's underside (.270): the hole is .040 into the floor, .040 short of the underside."}]},"tail_step_length":{"label":"The tail's narrower rear end, its length","kind":"length","measurements":[{"id":"tdp","value":0.375,"unit":"in","pm":0.015,"stated":".375±.015, 2 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 8448592 (Trigger), rev L, scale 2/1, sheet 1 of 1; user-supplied scan (Distribution Statement F, Colt proprietary notice), PDF page 43 (references/aero-m4e1-lower 1dabf089edf8)","via":"user"},"note":"Section A-A: from the tail's end forward to the step, each side (117 px, 0.371). The top view has the step 0.85 behind the pivot."}],"note":"The last of the tail is narrower on both sides. Both BCM side photos show the step as a line across the tail: 145 px from the end in Primary Arms' (0.377 at the 385 px/in its tail gives), 85 px in BCM's own (0.39 at 216)."},"tail_step_depth":{"label":"The tail's narrower rear end, how far each side stands in","kind":"length","measurements":[{"id":"tdp","value":0.013,"unit":"in","pm":0.003,"stated":".013±.003, 2 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 8448592 (Trigger), rev L, scale 2/1, sheet 1 of 1; user-supplied scan (Distribution Statement F, Colt proprietary notice), PDF page 43 (references/aero-m4e1-lower 1dabf089edf8)","via":"user"},"note":"Section A-A: between the body's side and the rear end's, each side."}]},"blade_face_r":{"label":"The blade's face, the radius it is rounded on from side to side","kind":"length","measurements":[{"id":"tdp","value":0.375,"unit":"in","pm":0.015,"stated":".375 R±.015","source":{"type":"standard","doc":"US Army TDP drawing 8448592 (Trigger), rev L, scale 2/1, sheet 1 of 1; user-supplied scan (Distribution Statement F, Colt proprietary notice), PDF page 43 (references/aero-m4e1-lower 1dabf089edf8)","via":"user"},"note":"Section A-A (through the blade .97 below the pivot, looking up): the hatched section's front, an arc about a centre on the centre plane .375 behind the face; the arc drawn on round under the body passes through that centre's .375. Across the .290 it falls back 0.029 at each side. (Its second callout in that view, .375±.015 2 PLACES, is the tail's step.)"}]},"blade_section_length":{"label":"The blade's section in Section A-A, front to back","kind":"length","measurements":[{"id":"section","value":0.194,"unit":"in","pm":0.013,"source":{"type":"photo","photo":"references/aero-m4e1-lower 1dabf089edf8 (US Army TDP drawing 8448592 (Trigger) rev L, the user's M16 TDP scan, PDF page 43: Section A-A)","scaleRef":"the body's .290 (-B-) in the same section, 92 px between its two sides' strokes: 317 px/in","method":"the hatched section's rear apex (u 3013) to its front apex (u 3074): 61 px; ± 4 px of a 5 px stroke on a 1-bit scan","via":"user"},"note":"The side elevation's blade at that height is 0.18 through (the traced outline): the same within the strokes."}]},"blade_back_depth":{"label":"The blade's back, how deep its rounding is in Section A-A","kind":"length","measurements":[{"id":"section","value":0.107,"unit":"in","pm":0.013,"source":{"type":"photo","photo":"references/aero-m4e1-lower 1dabf089edf8 (US Army TDP drawing 8448592 (Trigger) rev L, the user's M16 TDP scan, PDF page 43: Section A-A)","scaleRef":"the body's .290 (-B-) in the same section, 92 px between its two sides' strokes: 317 px/in","method":"the hatched section's rear apex (u 3013) to where its outline reaches the body's sides (u 3047, both sides): 34 px; ± 4 px. An arc through those three points has a radius of 0.148, half the width: nearly a full round","via":"user"}}],"note":"The drawing gives the back no radius: the section draws it round from the full width to its rear apex. What is left between this and the face's fall is the flank at the full width, 0.058 (0.194 - 0.107 - 0.029). The side elevation says the same another way: an inner arc on the blade (.71 R, about the centre of the face's .62 R) runs .09 behind the face, where the flank ends (0.194 - 0.107 = 0.087). Primary Arms' side photo shows that line on the blade, about half way through it."},"web_from_below_pivot":{"label":"Where the sweep from the block leaves the blade's face, below the pivot's axis","kind":"length","measurements":[{"id":"elevation","value":0.75,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/aero-m4e1-lower 1dabf089edf8 (US Army TDP drawing 8448592 (Trigger) rev L, the user's M16 TDP scan, PDF page 43: the side elevation)","scaleRef":"the elevation's own frame: the pivot at (3051, 2877), 315.2 px/in by the tail's 1.210 -.015","method":"where the blade's inner line and its outer silhouette part, v 3105 to 3120 (the .71 R leader's arrowhead lies across the two there): 0.72 to 0.77 below the pivot's centre line","via":"user"}}],"note":"Below this the blade's silhouette is its face; above it the silhouette runs forward to the block's corner while the flank's own front line goes straight up to the block. The model's prow begins here."},"edge_r":{"label":"Edges and corners left as cast, radius","kind":"length","measurements":[{"id":"tdp","value":0.031,"unit":"in","pm":0.005,"stated":"FILLET, EDGE AND CORNER RADII .031, UNLESS OTHERWISE SPECIFIED.","source":{"type":"standard","doc":"US Army TDP drawing 8448592 (Trigger), rev L, scale 2/1, sheet 1 of 1; user-supplied scan (Distribution Statement F, Colt proprietary notice), PDF page 43 (references/aero-m4e1-lower 1dabf089edf8)","via":"user"},"note":"Note 3. Machined edges are broken .010 at most (note 11)."}]},"tail_top_above_pivot":{"label":"The tail's top above the pivot's axis","kind":"length","measurements":[{"id":"tdp","value":0.058,"unit":"in","pm":0.002,"stated":".058±.002, SEE NOTE 7","source":{"type":"standard","doc":"US Army TDP drawing 8448592 (Trigger), rev L, scale 2/1, sheet 1 of 1; user-supplied scan (Distribution Statement F, Colt proprietary notice), PDF page 43 (references/aero-m4e1-lower 1dabf089edf8)","via":"user"},"note":"The side elevation: from the pivot's centre line up to the tail's top (18 px, 0.057). A check on the traced outline."}]},"tail_bottom_below_pivot":{"label":"The tail's underside below the pivot's axis","kind":"length","measurements":[{"id":"tdp","value":0.27,"unit":"in","pm":0.005,"stated":".270","source":{"type":"standard","doc":"US Army TDP drawing 8448592 (Trigger), rev L, scale 2/1, sheet 1 of 1; user-supplied scan (Distribution Statement F, Colt proprietary notice), PDF page 43 (references/aero-m4e1-lower 1dabf089edf8)","via":"user"},"note":"The side elevation: from the pivot's centre line down to the tail's underside (85 px, 0.270); View E-E repeats it (.270, 4 PLACES). A check on the traced outline."}]},"block_bottom_below_pivot":{"label":"The block under the body ahead of the blade, its underside below the pivot's axis (-D-)","kind":"length","measurements":[{"id":"tdp","value":0.378,"unit":"in","pm":0.007,"stated":".378±.007 -D-","source":{"type":"standard","doc":"US Army TDP drawing 8448592 (Trigger), rev L, scale 2/1, sheet 1 of 1; user-supplied scan (Distribution Statement F, Colt proprietary notice), PDF page 43 (references/aero-m4e1-lower 1dabf089edf8)","via":"user"},"note":"The side elevation: from the pivot's centre line down to the block's underside (120 px, 0.381). A check on the traced outline."}]},"block_front_ahead_of_pivot":{"label":"The block under the body, its front ahead of the pivot","kind":"length","measurements":[{"id":"tdp","value":0.5,"unit":"in","pm":0.005,"stated":".500","source":{"type":"standard","doc":"US Army TDP drawing 8448592 (Trigger), rev L, scale 2/1, sheet 1 of 1; user-supplied scan (Distribution Statement F, Colt proprietary notice), PDF page 43 (references/aero-m4e1-lower 1dabf089edf8)","via":"user"},"note":"The side elevation: from the pivot's centre line forward to the block's front face (157 px, 0.498). Section A-A draws that end as a full round across the body's width (\".005 MAX FLASH ON THIS RADIUS PERMISSIBLE\"), its apex 0.495 ahead. A check on the traced outline."}]}}},{"subject":"bcm-qd-end-plate","title":"BCM QD end plate","dimensions":{"height":{"label":"End plate height (its top to its lobe's bottom)","kind":"length","measurements":[{"id":"faceon-hole","value":2.023,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-qd-end-plate f9569188119d (Primary Arms’ BCM-EPM4-QD_02, 2000 x 1333: the plate straight face-on on white, star side, the socket’s bore open to the white behind)","scaleRef":"the ring's hole taken as a mil-spec plate's (std.receiver_extension.end_plate_hole_d, 1.1902 in): 565 px across and 572 px high beside its key (threshold 200, holes of the largest piece), read as 570 ± 5 px, so 478.9 px/in ± 0.9%. Checked on what else it has to fit: at this scale the socket's opening is 0.370 in (a push-button swivel's stud is three eighths), and the socket is 0.979 in below the ring's centre, where the reference model's plate has its boss over the detent spring at 0.997","method":"the outline's height, 969 px (luminance < 200, largest piece, holes filled)","via":"harvest"},"note":"A mil-spec plate is 2.06 in the reference model; BCM's plain plate 2.01 as the ledger has it."}],"note":"What the face-on photo's outline (profiles.face) is scaled to."},"top_above_axis":{"label":"End plate top above the tube axis","kind":"length","measurements":[{"id":"faceon-hole","value":0.665,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/bcm-qd-end-plate f9569188119d (Primary Arms’ BCM-EPM4-QD_02, 2000 x 1333: the plate straight face-on on white, star side, the socket’s bore open to the white behind)","scaleRef":"the ring's hole taken as a mil-spec plate's (std.receiver_extension.end_plate_hole_d, 1.1902 in): 565 px across and 572 px high beside its key (threshold 200, holes of the largest piece), read as 570 ± 5 px, so 478.9 px/in ± 0.9%. Checked on what else it has to fit: at this scale the socket's opening is 0.370 in (a push-button swivel's stud is three eighths), and the socket is 0.979 in below the ring's centre, where the reference model's plate has its boss over the detent spring at 0.997","method":"the outline's top row (187) above the ring's hole's centre (row 505.5: the hole's centroid, a pixel lower for the key that stands in its bottom)","via":"harvest"}}]},"width":{"label":"End plate width (across its ring)","kind":"length","measurements":[{"id":"faceon-hole","value":1.334,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bcm-qd-end-plate f9569188119d (Primary Arms’ BCM-EPM4-QD_02, 2000 x 1333: the plate straight face-on on white, star side, the socket’s bore open to the white behind)","scaleRef":"the ring's hole taken as a mil-spec plate's (std.receiver_extension.end_plate_hole_d, 1.1902 in): 565 px across and 572 px high beside its key (threshold 200, holes of the largest piece), read as 570 ± 5 px, so 478.9 px/in ± 0.9%. Checked on what else it has to fit: at this scale the socket's opening is 0.370 in (a push-button swivel's stud is three eighths), and the socket is 0.979 in below the ring's centre, where the reference model's plate has its boss over the detent spring at 0.997","method":"the outline's width, 639 px","via":"harvest"},"note":"1.363 in the reference model; 1.32 for BCM's plain plate."}]},"thickness":{"label":"End plate thickness","kind":"length","measurements":[{"id":"edge","value":0.115,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/bcm-qd-end-plate 5818bed9fa7e (BCM’s BCM-EPM4-QD-4, 1200 x 800: the plate nearly edge-on on white, turned about ten degrees, the ring a narrow ellipse)","scaleRef":"the plate's own height in the same view, 459 px, taken as the face-on photo's (.height): 227 px/in at the plate's middle. A close photo: the near side of the ring reads a quarter larger than the far side, so what is read on one side only carries that","method":"the ring's two sides across the photo at its middle height: the near one's edge 30 px, the far one's inner wall and face 24 px, each less what the face shows at ten degrees (3 px), and halved between the two for the lens's nearness","via":"harvest"},"note":"A mil-spec plate is 0.124 in the reference model, inside this ±."}]},"socket_below_axis":{"label":"QD socket, its centre below the tube axis","kind":"length","measurements":[{"id":"faceon-hole","value":0.979,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/bcm-qd-end-plate f9569188119d (Primary Arms’ BCM-EPM4-QD_02, 2000 x 1333: the plate straight face-on on white, star side, the socket’s bore open to the white behind)","scaleRef":"the ring's hole taken as a mil-spec plate's (std.receiver_extension.end_plate_hole_d, 1.1902 in): 565 px across and 572 px high beside its key (threshold 200, holes of the largest piece), read as 570 ± 5 px, so 478.9 px/in ± 0.9%. Checked on what else it has to fit: at this scale the socket's opening is 0.370 in (a push-button swivel's stud is three eighths), and the socket is 0.979 in below the ring's centre, where the reference model's plate has its boss over the detent spring at 0.997","method":"the socket's opening's centre (row 973.2) below the ring's hole's centre","via":"harvest"}}]},"socket_bore_d":{"label":"QD socket, its bore","kind":"length","measurements":[{"id":"faceon-hole","value":0.37,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-qd-end-plate f9569188119d (Primary Arms’ BCM-EPM4-QD_02, 2000 x 1333: the plate straight face-on on white, star side, the socket’s bore open to the white behind)","scaleRef":"the ring's hole taken as a mil-spec plate's (std.receiver_extension.end_plate_hole_d, 1.1902 in): 565 px across and 572 px high beside its key (threshold 200, holes of the largest piece), read as 570 ± 5 px, so 478.9 px/in ± 0.9%. Checked on what else it has to fit: at this scale the socket's opening is 0.370 in (a push-button swivel's stud is three eighths), and the socket is 0.979 in below the ring's centre, where the reference model's plate has its boss over the detent spring at 0.997","method":"the opening seen through the socket, 180 px wide and 174 high (its area's equal circle 177 px)","via":"harvest"},"note":"What shows through a socket from in front is its narrowest. T.REX ARMS: \"Accepts standard QD push-button sling swivels.\" No page states the bore."}]},"socket_od":{"label":"QD socket, its collar's outside diameter","kind":"length","measurements":[{"id":"faceon-hole","value":0.547,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-qd-end-plate f9569188119d (Primary Arms’ BCM-EPM4-QD_02, 2000 x 1333: the plate straight face-on on white, star side, the socket’s bore open to the white behind)","scaleRef":"the ring's hole taken as a mil-spec plate's (std.receiver_extension.end_plate_hole_d, 1.1902 in): 565 px across and 572 px high beside its key (threshold 200, holes of the largest piece), read as 570 ± 5 px, so 478.9 px/in ± 0.9%. Checked on what else it has to fit: at this scale the socket's opening is 0.370 in (a push-button swivel's stud is three eighths), and the socket is 0.979 in below the ring's centre, where the reference model's plate has its boss over the detent spring at 0.997","method":"the collar's face about the socket's centre: mean brightness by radius steps down at 131 px (the collar's face 65 of 255, the plate's 48)","via":"harvest"}}]},"socket_proud_rear":{"label":"QD socket, how far its collar stands out of the star face (the rear, as BCM says to install it)","kind":"length","measurements":[{"id":"edge","value":0.12,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-qd-end-plate 5818bed9fa7e (BCM’s BCM-EPM4-QD-4, 1200 x 800: the plate nearly edge-on on white, turned about ten degrees, the ring a narrow ellipse)","scaleRef":"the plate's own height in the same view, 459 px, taken as the face-on photo's (.height): 227 px/in at the plate's middle. A close photo: the near side of the ring reads a quarter larger than the far side, so what is read on one side only carries that","method":"the collar on the face turned to the camera, 52 px across the photo at its middle, less its own end face seen at ten degrees (its diameter's 0.55 in times the sine: 25 px)","via":"harvest"},"note":"Which face: BCM's oblique (0c02d8b792b8) has the long collar, knurled where it is pressed into the plate, on the star's side; T.REX ARMS: \"Install with the Star Logo out.\""}]},"socket_proud_front":{"label":"QD socket, how far it stands out of the front face (into the receiver's rear face, where a plain plate has its boss)","kind":"length","measurements":[{"id":"edge","value":0.1,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-qd-end-plate 5818bed9fa7e (BCM’s BCM-EPM4-QD-4, 1200 x 800: the plate nearly edge-on on white, turned about ten degrees, the ring a narrow ellipse)","scaleRef":"the plate's own height in the same view, 459 px, taken as the face-on photo's (.height): 227 px/in at the plate's middle. A close photo: the near side of the ring reads a quarter larger than the far side, so what is read on one side only carries that","method":"what stands off the face turned away from the camera, 22 px across the photo (its end face doesn't show)","via":"harvest"},"note":"A mil-spec plate's boss stands 0.0645 out in the reference model. Its diameter on this side isn't read: drawn as the collar's."}]},"face_mean_width":{"label":"Its face's area over its height (the width of a rectangle as tall with the same area)","kind":"length","measurements":[{"id":"outline","value":0.986,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-qd-end-plate f9569188119d (Primary Arms’ BCM-EPM4-QD_02, 2000 x 1333: the plate straight face-on on white)","scaleRef":"the traced outline's own scale (profiles.face: its height, .height)","method":"the traced outline's area (1.995 square inches, the hole and the socket filled) over its height (2.023 in)","via":"harvest"}}],"note":"A way to hold the outline's area as a length: what the plate's weight is worked out from."},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"metal","value":0.54,"unit":"oz","pm":0.1,"source":{"type":"derived","expr":"(({.face_mean_width} * {.height} - 0.785398163 * {std.receiver_extension.end_plate_hole_d} * {std.receiver_extension.end_plate_hole_d}) * {.thickness} + 0.785398163 * ({.socket_od} * {.socket_od} - {.socket_bore_d} * {.socket_bore_d}) * ({.socket_proud_rear} + {.socket_proud_front}) - 0.785398163 * {.socket_bore_d} * {.socket_bore_d} * {.thickness}) * {std.density.steel}","via":"harvest"},"note":"Its face's area less the hole for the extension, through its thickness; the socket's collar where it stands out of each face; less the socket's bore through the plate. Nearly all of the ± is the thickness's, read to ± 0.025 on one photo (0.45 to 0.62 oz across it)."},{"id":"ar15discounts","value":1.008,"unit":"oz","pm":0.1,"stated":"Weight 1.008 oz Dimensions 3.35 × 0.65 × 0.65 in","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, BCMGUNFIGHTER QD End Plate (BCM-EPM4-QD)","url":"https://ar15discounts.com/products/bcmgunfighter-qd-end-plate/","retrieved":"2026-10-12","via":"harvest"},"note":"What was weighed isn't said (0.063 lb to the thousandth, as a shop's shipping table has it), and the dimensions beside it aren't a plate's: taken to ± 0.1 oz."}],"adopt":{"from":"metal","reason":"The seller's 1.008 oz comes with dimensions that aren't a plate's (3.35 x 0.65 x 0.65 in) and doesn't say what was weighed: a shipping table's entry by its look. The steel of the plate as its photos have it is half an ounce, as a plain plate's is with the socket's collar more."},"note":"BCM states none. The plate's own steel worked out from its sizes, and one seller's figure beside it, which is nearly twice that: the plate would have to be a quarter of an inch thick to weigh it, and BCM's edge-on photo has it an eighth at most."}}},{"subject":"bcm-receiver-extension","title":"BCM mil-spec carbine receiver extension (the 6-position buffer tube)","dimensions":{"tube_od":{"label":"Receiver extension OD","kind":"length","measurements":[{"id":"std","value":1.148,"unit":"in","source":{"type":"derived","expr":"{std.receiver_extension.milspec_od}","via":"brief"},"note":"The kit is listed as a mil-spec tube, so the standard applies."},{"id":"moe-sl-photo","value":1.133,"unit":"in","source":{"type":"photo","photo":"Magpul MOE SL side product photo (not yet archived)","scaleRef":"not recorded in brief","method":"exposed tube measured in the calibrated photo","via":"brief"},"note":"1.3% below the standard, which points to photo scale error at the tube."}],"adopt":{"from":"std","reason":"Mil-spec standard. The photo reading doubles as a check on that photo's calibration. Caliper to confirm."}},"tube_front_behind_pin":{"label":"Receiver extension's front face behind the takedown pin (how far it screws in)","kind":"length","measurements":[{"id":"std","value":0.669,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"-{std.receiver_extension.front_face_x}","via":"user"},"note":"The Army's drawings: screwed in until its edge stands over the buffer retainer's shoulder."},{"id":"magpul-photo","value":0.6,"unit":"in","pm":0.09,"source":{"type":"photo","photo":"references/magpul-moe-carbine 5f6775e35c7e (Magpul: an M4 with the MOE Carbine stock two steps out, right side, close, 1200 px)","scaleRef":"the stock's own length, 641.4 px for Magpul's 7.0 in: 91.6 px/in","method":"the stock's lock pin (its shaft over columns 530 to 553) is 500.5 px behind the takedown pin's head (1042, between its two highlights): 5.46 in, less up to 0.07 for the head standing nearer the lens than the tube: 5.43. Two steps out, the pin is in the third hole from the front, which this tube has 4.83 in behind its front face (tube_length − position_hole_rear_from_rear − 3 × position_step)","via":"harvest"},"note":"Another maker's tube on Magpul's rifle; ± adds the hole's place and the tube's generic length."}],"adopt":{"from":"std","reason":"From the drawings of the parts that set it; the photo of a rifle agrees within its ±."},"note":"M5 drew the tube from the takedown pin's X, an assumption the app listed. It is hidden inside the receiver; what it moves is the tube's rear end, its rail's ramp and its six holes, 0.67 in back."},"tube_length":{"label":"Receiver extension length","kind":"length","measurements":[{"id":"generic","value":7.25,"unit":"in","stated":"7.25 inches (Carbine Length)","source":{"type":"spec","publisher":"retailer","name":"Dirty Bird (One Horse mil-spec carbine tube, not BCM)","url":"https://dirtybirdusa.com/products/one-horse-mil-spec-6-position-receiver-extension-buffer-tube/","retrieved":"2026-09-30","via":"harvest"},"note":"Generic mil-spec carbine figure. BCM publishes none."},{"id":"generic-2","value":7.25,"unit":"in","stated":"Approx. 7.25 inches","source":{"type":"spec","publisher":"review","name":"Mounts Plus (generic mil-spec article)","url":"https://mountsplus.com/milspec-buffer-tube.html","retrieved":"2026-09-30","via":"harvest"}}],"adopt":{"from":"generic","reason":"Two generic sources agree; not BCM-specific, so it stays provisional."}},"position_hole_d":{"label":"Receiver extension position holes, diameter (in the rail)","kind":"length","measurements":[{"id":"bcm","value":0.42,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-stock-kit 0386d6432abe (BCM mil-spec carbine receiver extension, underside, 1280 px)","scaleRef":"the tube's 7.25 in (tube_length) = 1166 px (160.8 px/in); the rail is nearer the lens, so its features read ~2% large","method":"the rear hole's outline on a 4x crop, 69 px across","via":"harvest"},"note":"Blind, from the rail up to the tube's wall (Magpul's identification card: about 0.30 deep, which is the rail's depth below the tube)."}]},"position_step":{"label":"Receiver extension position holes, spacing (what a stock moves per position)","kind":"length","measurements":[{"id":"magpul","value":0.66,"unit":"in","source":{"type":"derived","expr":"{magpul-moe-sl-carbine.position_step}","via":"brief"},"note":"Magpul's MOE SL travel over a mil-spec carbine tube's six positions."}],"note":"A property of the tube: any stock on it moves by this. BCM publishes no figure. Magpul states its stocks' travel on a mil-spec carbine tube (3.3 in over six positions); the six holes in BCM's underside photo read 0.68 apart at the silhouette's scale, the rail being nearer the lens (about 2% large), which agrees."},"position_hole_rear_from_rear":{"label":"Receiver extension rear position hole, centre ahead of the tube's rear face","kind":"length","measurements":[{"id":"bcm","value":0.44,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-stock-kit 0386d6432abe (BCM mil-spec carbine receiver extension, underside, 1280 px)","scaleRef":"the tube's 7.25 in (tube_length) = 1166 px (160.8 px/in), corrected ~2% for the rail's nearness","method":"the rear hole's centre (px 1135.5, from its outline on a 4x crop) to the rear face (px 1209): 73.5 px","via":"harvest"}}],"note":"Six holes at the tube's position step (position_step)."},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"metal","value":3.76,"unit":"oz","pm":0.2,"source":{"type":"derived","expr":"(0.785398163 * ({.tube_od} * {.tube_od} - {std.receiver_extension.bore_d} * {std.receiver_extension.bore_d}) * {.tube_length} + 0.785398163 * {std.receiver_extension.bore_d} * {std.receiver_extension.bore_d} * {std.receiver_extension.carbine_rear_wall} + {std.receiver_extension.rail_width} * ({std.receiver_extension.rail_bottom_below_axis} - {.tube_od} / 2) * ({.tube_length} - {std.receiver_extension.rail_ramp_end}) - 6 * 0.785398163 * {.position_hole_d} * {.position_hole_d} * ({std.receiver_extension.rail_bottom_below_axis} - {.tube_od} / 2)) * {std.density.aluminium_7075}","via":"harvest"}}],"note":"No maker's or seller's figure: BCM states none for the extension alone. Worked out from its sizes: the tube's wall round its bore along its length, its rear wall, and its rail less the six position holes, as 7075 (BCM: \"machined from 7075T6\"). A derived figure, for the build's total. The model drawn from the same sizes holds 2.36 cubic inches, 2% more than this formula's (its ramp, its thread's crests and the rail's seat on the round), which the ± covers with the wall's own: a bore two thousandths large is 1%."}}},{"subject":"bcm-rifle-m16-action-spring","title":"BCM Rifle M16 Action Spring","dimensions":{"wire_d":{"label":"Wire diameter","kind":"length","measurements":[{"id":"tdp","value":0.072,"unit":"in","pm":0.001,"stated":"WIRE DIA: .072±.001","source":{"type":"standard","doc":"US Army TDP drawing 8448629 (Spring, Action), rev C, PDF page 36, spring data; user-supplied scan (references/…/Spec_Sheets/M16_Technical_Data_Package.pdf), crops in .cache/buffer/std","via":"user"}}]},"od":{"label":"Outside diameter of its coils","kind":"length","measurements":[{"id":"tdp","value":0.94,"unit":"in","pm":0.015,"stated":".940 DIA±.015","source":{"type":"standard","doc":"US Army TDP drawing 8448629 (Spring, Action), rev C, PDF page 36; user-supplied scan, crops in .cache/buffer/std","via":"user"}},{"id":"photo","value":0.926,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-mk2-receiver-extension da2d35d9e02d (BCM's MK2 stock kit on white, from above, 1000 x 667)","scaleRef":"the MK2 tube beside it, 525.5 px for its 7.955 in (bcm-mk2-receiver-extension.tube_length): 66.06 px/in","method":"the coils' width across the middle fifth of its length, 61.2 px","via":"harvest"},"note":"A wire two pixels thick: its edge's blur takes a pixel or two off the width."}],"adopt":{"from":"tdp","reason":"The Army's drawing; BCM's photo agrees within its ±."}},"end_coil_od":{"label":"Outside diameter of the one reduced coil at each end","kind":"length","measurements":[{"id":"tdp","value":0.9,"unit":"in","pm":0.015,"stated":".900 DIA±.015 REDUCE (1) COIL BOTH ENDS","source":{"type":"standard","doc":"US Army TDP drawing 8448629 (Spring, Action), rev C, PDF page 36; user-supplied scan, crops in .cache/buffer/std","via":"user"}}]},"free_length":{"label":"Free length","kind":"length","measurements":[{"id":"tdp","value":12.5,"unit":"in","pm":0.05,"stated":"12.50 FREE LENGTH AFTER SETTING, REF","source":{"type":"standard","doc":"US Army TDP drawing 8448629 (Spring, Action), rev C, PDF page 36; user-supplied scan, crops in .cache/buffer/std","via":"user"},"note":"A reference figure (REF): the drawing holds the spring to its loads (load_operating, load_assembled), not to this."},{"id":"kit-photo","value":12.48,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/bcm-mk2-receiver-extension da2d35d9e02d (BCM's MK2 stock kit on white, from above, 1000 x 667)","scaleRef":"the MK2 tube beside it, 525.5 px for its 7.955 in (bcm-mk2-receiver-extension.tube_length, read on BCM's side photo at the scale of its own thread): 66.06 px/in","method":"its length along its principal axis, 824.7 px (.cache/batch15/bcm-mk2-tools/crests.py)","via":"harvest"}},{"id":"bcm-photo","value":12.8,"unit":"in","pm":0.4,"source":{"type":"photo","photo":"references/bcm-rifle-m16-action-spring b7afddafe667 (BCM's Spring_Rifle_M16_Action-2: the whole spring on white, lying on the diagonal, 1024 x 1024)","scaleRef":"the spring's own width in the middle fifth of its length, 76.7 px, as the drawing's .940 outside diameter: 81.6 px/in","method":"its length along its principal axis, 1041.7 px; at its widest (84.1 px) the same length is 11.6 in, which the ± covers","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The Army's drawing of the M16 spring; BCM's photo of it beside a tube of known length has it to 0.02 in."}},"coils":{"label":"Total coils","kind":"count","measurements":[{"id":"photo","value":43.5,"unit":"count","pm":1,"source":{"type":"photo","photo":"references/bcm-rifle-m16-action-spring b7afddafe667 (BCM's photo of the spring on white, 1024 x 1024) and references/bcm-mk2-receiver-extension da2d35d9e02d (BCM's MK2 stock kit, the spring free beside the tube)","scaleRef":"none: a count","method":"the crests of the outline along each side of its axis (.cache/batch15/bcm-mk2-tools/crests.py): 42 and 43 on BCM's own photo, where one side has a gap of 43 px at a 24 px spacing (a crest missed: 43); 43 and 44 on the kit photo, 19 px apart","via":"harvest"}},{"id":"tdp","value":44,"unit":"count","stated":"TOTAL COILS: 44 REF","source":{"type":"standard","doc":"US Army TDP drawing 8448629 (Spring, Action), rev C, PDF page 36, spring data; user-supplied scan, crops in .cache/buffer/std","via":"user"}}],"adopt":{"from":"photo","reason":"Counted on BCM's own springs, as the carbine spring's coils are; the Army's 44 is a reference figure and within the count's ±."}},"solid_length":{"label":"Solid length (every coil touching)","kind":"length","measurements":[{"id":"tdp","value":3.285,"unit":"in","stated":"SOLID LENGTH: 3.285 MAX","source":{"type":"standard","doc":"US Army TDP drawing 8448629 (Spring, Action), rev C, PDF page 36, spring data; user-supplied scan, crops in .cache/buffer/std","via":"user"},"note":"A maximum, not drawn: what the spring can't be compressed past."}]},"assembled_length_rifle":{"label":"Its mean assembled length in the M16 rifle (bolt forward)","kind":"length","measurements":[{"id":"tdp","value":8.19,"unit":"in","pm":0.005,"stated":"LOAD AT COMPRESSED LG OF 8.190 MEAN ASSEMBLED LENGTH = 5.8 LBS±.5 LBS","source":{"type":"standard","doc":"US Army TDP drawing 8448629 (Spring, Action), rev C, PDF page 36, spring data; user-supplied scan, crops in .cache/buffer/std","via":"user"}}],"note":"In the M16 rifle's own extension, which this spring was drawn for; not its length in the MK2 tube (installed_length)."},"installed_length":{"label":"Its length as drawn: in BCM's MK2 tube, from the MK2 buffer's seat to the tube's rear wall, bolt forward","kind":"length","measurements":[{"id":"room","value":7.677,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{bcm-mk2-receiver-extension.tube_front_behind_pin} + {bcm-mk2-receiver-extension.tube_length} - {bcm-mk2-receiver-extension.rear_wall} + {std.ar15.upper_rear_face_x} - {bcm-mk2-buffer-t0.head_thickness}","via":"harvest"}}],"note":"What the spring is drawn at: the system BCM sells it in with this batch (its MK2 kits: \"Mil-Spec M16A4 rifle action spring\"). The MK2 buffer's face rests at the upper receiver's rear face (the carrier's rear end, bolt forward); the spring bears on the rear face of the buffer's head and on the tube's rear wall inside. 0.51 in shorter than the M16 rifle's mean assembled length (assembled_length_rifle)."},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"wire","value":2.2,"unit":"oz","pm":0.15,"source":{"type":"derived","expr":"3.14159265 * ({.od} - {.wire_d}) * {.coils} * 0.785398163 * {.wire_d} * {.wire_d} * {std.density.steel}","via":"harvest"}}],"note":"No maker's or seller's figure: BCM states none. Worked out from its wire: the wire's length round its coils times its section times what steel weighs (the Army's drawing: \"WIRE, STAINLESS STEEL, TYPE 631, (17-7PH) COLD DRAWN, ASTM A313\"; a stainless steel within the steel density's ±). A derived figure, for the build's total."}}},{"subject":"bcm-stock-mod-0","title":"BCM Stock - Mod 0 (BCM-GFS-MOD-0-BLK)","dimensions":{"length":{"label":"Overall length","kind":"length","measurements":[{"id":"wing","value":6.75,"unit":"in","stated":"Length: 6.75\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Bravo Company BCMGUNFIGHTER MOD 0 Stock (Specifications)","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/stocks-accessories/bravo-company-bcmgunfighter-mod-0-stock/","retrieved":"2026-10-05","via":"harvest"},"note":"The seller's figure; how it was taken isn't said."},{"id":"patent","value":6.657,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-stock-mod-0 b3de05737376 (US 9,109,855 B1, Bravo Company USA, sheet 4 of 7: FIG. 4A, sectional side view of the stock on a receiver extension)","scaleRef":"the receiver extension drawn in the stock: its outer limbs at rows 550.5 and 725.5 (column 1300), 175 px for std.receiver_extension.milspec_od = 1.148 in: 152.4 px/in. The tube's position pockets repeat every 99.3 px there, 0.652 in (the standard's step is 0.66)","method":"the stock's front face (column 1397.5) to the butt pad's rearmost point (column 2412): 1014.5 px; ± for the strokes (a pixel on the tube's 175)","via":"harvest"}},{"id":"installed-rifle","value":6.637,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/bcm-stock-mod-0 824d597175f5 (BCM, MOD 0 STOCK SERIES brochure, page 3: a rifle with the Flat Dark Earth stock, straight right side, 1280 x 800)","scaleRef":"frame from the receiver's pins on its right side: the selector (437.4, 403.6), the trigger pin (475.3, 410.2) and the hammer pin (503.7, 400.1) stand 33.69 px/in apart by std.ar15.selector_x, trigger_pin_x and hammer_pin_x (the three pairs agree to 0.01) and put the takedown pin at column 410.35; the pivot pin's head is at 625.5 by eye, 625.1 by that frame; the pins' heights agree with the standard within a pixel","method":"the butt's rearmost point (column 37.5, rows 348 to 356, at the 50% level against the dark ground) to the cheek's front face against the black tube (column 261.1, rows 348 to 372): 223.6 px; ± for the two edges and the scale","via":"harvest"}}],"adopt":{"from":"patent","reason":"BCM's own section drawing, at the scale of the mil-spec tube it is drawn on, and BCM's own photo of the stock on a rifle, at the scale of the receiver's pins, agree within 0.02 in. The seller's 6.75 is 1.4% over both and isn't explained (its height and width agree with the drawing)."},"note":"The one published figure, a seller's, is 0.09 in over two measurements that agree: BCM's patent section at the scale of the tube drawn in it, and BCM's photo of the stock on a rifle at the scale of the receiver's pins. The same seller's height and width agree with the patent within 0.2%. The seller's straight side photo reads longer still against its height (1709 x 1227 px: 6.82 in for 4.9): its ends are the stock's near edges, which stand nearer the lens than the top and the toe."},"height":{"label":"Height","kind":"length","measurements":[{"id":"wing","value":4.9,"unit":"in","stated":"Height: 4.9\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Bravo Company BCMGUNFIGHTER MOD 0 Stock (Specifications)","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/stocks-accessories/bravo-company-bcmgunfighter-mod-0-stock/","retrieved":"2026-10-05","via":"harvest"}},{"id":"guns-america","value":5,"unit":"in","stated":"The buttpad is small, only 5 inches, and that makes it fast to shoulder even when wearing a heavy jacket.","source":{"type":"spec","publisher":"review","name":"Guns America Digest, AR Stock Hack: Magpul CTR vs. BCM Gunfighter Mod 0 (Robert Sadowski, 2024-04-13)","url":"https://gunsamerica.com/digest/ar-stock-hack-magpul-ctr-vs-bcm-gunfighter-mod-0/","retrieved":"2026-10-05","via":"harvest"},"note":"The butt pad runs the stock's whole height. The article doesn't say how it was measured."},{"id":"patent","value":4.91,"unit":"in","pm":0.07,"source":{"type":"photo","photo":"references/bcm-stock-mod-0 b3de05737376 (US 9,109,855 B1, sheet 4 of 7: FIG. 4A, sectional side view)","scaleRef":"the receiver extension drawn in the stock, 175 px for std.receiver_extension.milspec_od = 1.148 in: 152.4 px/in","method":"the rear body's top (row 529.5 at column 2330: it stands 10 px above the cheek's top, row 539.5) to the toe's underside (row 1277.5 at columns 2290 to 2310): 748 px","via":"harvest"}}],"adopt":{"from":"wing","reason":"A published figure; a reviewer's rounder one and the patent's section scaled by its own tube agree with it."}},"width":{"label":"Width","kind":"length","measurements":[{"id":"wing","value":1.67,"unit":"in","stated":"Width: 1.67\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Bravo Company BCMGUNFIGHTER MOD 0 Stock (Specifications)","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/stocks-accessories/bravo-company-bcmgunfighter-mod-0-stock/","retrieved":"2026-10-05","via":"harvest"}},{"id":"guns-america","value":1.7,"unit":"in","stated":"The comb is 1.7 inches wide and smooth.","source":{"type":"spec","publisher":"review","name":"Guns America Digest, AR Stock Hack: Magpul CTR vs. BCM Gunfighter Mod 0 (Robert Sadowski, 2024-04-13)","url":"https://gunsamerica.com/digest/ar-stock-hack-magpul-ctr-vs-bcm-gunfighter-mod-0/","retrieved":"2026-10-05","via":"harvest"}}],"adopt":{"from":"wing","reason":"The finer of two published figures that agree: the reviewer's rounds to it. It is the width across the rear body's side wings: the patent's rear view (FIG. 3B), scaled by the height, is 1.67 in across them and narrower across the body (body_width)."}},"body_width":{"label":"Width of the body: the cheek round the tube, the lever under it and the butt","kind":"length","measurements":[{"id":"patent","value":1.462,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-stock-mod-0 754ef4883e9b (US 9,109,855 B1 (Bravo Company USA), FIG. 3B rear view, sheet 3 of 7)","scaleRef":"scale from bcm-stock-mod-0.height = 4.9 in (y-extent 848 px → 173.1 px/in)","method":"width of the traced outline (tools/trace.py); the outline's width with the two ears (the rear body's side wings) left out: the body's sides","via":"harvest"}}],"note":"The published width is across the rear body's two side wings, which lap over the main body's sides and stand proud of them. The patent's rear view shows both: the wings as ears either side of the outline, 0.66 to 1.59 in below the top."},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"primary-arms","value":8.2,"unit":"oz","stated":"Weight 8.2 Oz","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, BCM-GFS-MOD-0-BLK (specification table; its feature list says \"8.2 oz weight\")","url":"https://www.primaryarms.com/bravo-company-manufacturing-bcm-gunfighter-mod-0-stock-black","retrieved":"2026-10-05","via":"harvest"}},{"id":"dirty-bird","value":8.208,"unit":"oz","stated":"Weight 8.208 oz","source":{"type":"spec","publisher":"retailer","name":"Dirty Bird Industries, BCMGUNFIGHTER Stock - MOD 0 (Additional information)","url":"https://dirtybirdusa.com/products/bcmgunfighter-stock-mod-0/","retrieved":"2026-10-05","via":"harvest"},"note":"To three decimals: a converted figure (0.513 lb), its source not stated. It may be the same figure Primary Arms rounds."},{"id":"wing","value":8.4,"unit":"oz","stated":"Weight: 8.4 oz.","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Bravo Company BCMGUNFIGHTER MOD 0 Stock (Specifications)","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/stocks-accessories/bravo-company-bcmgunfighter-mod-0-stock/","retrieved":"2026-10-05","via":"harvest"}},{"id":"tfb","value":7.5,"unit":"oz","stated":"Weighing in at just 7.5 ounces, the BCM Gunfighter Stock is significantly lighter than both the Vltor EMod’s 13.7 oz weight and the 10.7 oz. B5 Systems Enhanced SOPMOD.","source":{"type":"spec","publisher":"review","name":"The Firearm Blog, Bravo Company's BCM Gunfighter Stock (Timothy G. Yan, 2014-05-04)","url":"https://www.thefirearmblog.com/blog/2014/05/04/bravo-companys-bcm-gunfighter-stock/","retrieved":"2026-10-05","via":"harvest"},"note":"A test sample at the stock's launch; nothing says he weighed it."},{"id":"guns-america","value":7.5,"unit":"oz","stated":"The entire stock is snag-free and weighs a scant 7.5 ounces.","source":{"type":"spec","publisher":"review","name":"Guns America Digest, AR Stock Hack: Magpul CTR vs. BCM Gunfighter Mod 0 (Robert Sadowski, 2024-04-13)","url":"https://gunsamerica.com/digest/ar-stock-hack-magpul-ctr-vs-bcm-gunfighter-mod-0/","retrieved":"2026-10-05","via":"harvest"},"note":"The launch coverage's figure, ten years on; nothing says he weighed it."}],"adopt":{"from":"primary-arms","reason":"Two sellers' current pages agree (8.2 and 8.208 oz), and a third says 8.4. The 7.5 oz in the reviews is the figure of the 2014 launch, which BCM's own text of the time put at \"just over 7 ounces\"; none of the five was weighed by whoever states it, so it stays a seller's figure."},"note":"BCM states none. The Firearm Blog's second piece (2014-10-20) carries BCM's launch text: \"Weighing in just over 7 ounces, the BCMGUNFIGHTER™ Stock is the toughest lightweight polymer stock for Mil-Spec receivers being made today.\" No one on file says they put it on a scale. KYGUNCO's \"2 lb\" is its default (the same on its grip and trigger pages) and Big Tex Ordnance's \"6 oz\" has no source: neither is entered."},"tube_axis_below_top":{"label":"Tube axis below the stock's top edge (at its highest: the rear body's top)","kind":"length","measurements":[{"id":"patent","value":0.712,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-stock-mod-0 b3de05737376 (US 9,109,855 B1, sheet 4 of 7: FIG. 4A, sectional side view of the stock on a receiver extension)","scaleRef":"the receiver extension drawn in the stock, 175 px between its outer limbs for std.receiver_extension.milspec_od = 1.148 in: 152.4 px/in; the stock's length and height read 6.66 and 4.91 in at that scale against Wing's 6.75 and 4.9","method":"the tube's axis, midway between its outer limbs (rows 550.5 and 725.5 at column 1300: row 638.0), below the rear body's top (row 529.5 at column 2330): 108.5 px; ± for the strokes (2 px) and the scale","via":"harvest"}}],"note":"The rear body's top stands 0.066 in above the cheek's (10 px in the patent's section; the side photo shows the same step, 15 px at 250 px/in). Below the cheek's own top the axis is 0.646 in: the tube's radius and a wall 0.07 in thick, which is how the bore shows in Wing's photo of the stock from the front, all but touching the top."},"bore_depth":{"label":"The bore for the receiver extension: its depth from the stock's front face","kind":"length","measurements":[{"id":"patent","value":5.89,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/bcm-stock-mod-0 b3de05737376 (US 9,109,855 B1, sheet 4 of 7: FIG. 4A, sectional side view)","scaleRef":"the receiver extension drawn in the stock, 175 px for std.receiver_extension.milspec_od = 1.148 in: 152.4 px/in","method":"the stock's front face (column 1397.5) to the tube's rear face against the body's end wall (column 2295): 897.5 px","via":"harvest"}}],"note":"Collapsed, the tube's rear face stands against the main body's end wall (the section draws it so, the lock pin in the tube's front pocket). Recorded for the record: the model places the end wall from the butt (butt_behind_tube_rear_pos1), which is where the tube's rear face has to arrive."},"butt_behind_tube_rear_pos1":{"label":"Butt (the pad's rearmost point) behind the receiver extension's rear face, collapsed","kind":"length","measurements":[{"id":"patent","value":0.768,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-stock-mod-0 b3de05737376 (US 9,109,855 B1, sheet 4 of 7: FIG. 4A, sectional side view: the lock pin 145 in the tube's front pocket, five pockets 160 behind it)","scaleRef":"the receiver extension drawn in the stock, 175 px for std.receiver_extension.milspec_od = 1.148 in: 152.4 px/in","method":"the tube's rear face (column 2295, rows 640 and 700) to the pad's rearmost point (column 2412, rows 580 to 600): 117 px","via":"harvest"}}]},"lock_pin_behind_front":{"label":"Lock pin behind the stock's front face","kind":"length","measurements":[{"id":"patent","value":2.287,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-stock-mod-0 b3de05737376 (US 9,109,855 B1, sheet 4 of 7: FIG. 4A, sectional side view)","scaleRef":"the receiver extension drawn in the stock, 175 px for std.receiver_extension.milspec_od = 1.148 in: 152.4 px/in","method":"the shaft 145 in the tube's front pocket (its sides at columns 1722 and 1770: 0.31 in across, the pockets' own width) centred 348.5 px behind the stock's front face (column 1397.5); the five pockets behind it are centred 99.3 px apart from 1844","via":"harvest"}}],"note":"The steel block the lever draws down out of the receiver extension's pockets (the patent's locking block 135 and its shaft 145). Where it stands says which pocket the stock is on."},"butt_behind_pin_pos1":{"label":"Butt behind the takedown pin at position 1 (collapsed), on a carbine receiver extension","kind":"length","measurements":[{"id":"installed-rifle","value":8.427,"unit":"in","pm":0.07,"source":{"type":"derived","expr":"{.butt_behind_pin_pos5} - 4 * {bcm-receiver-extension.position_step}","via":"harvest"},"note":"BCM's photo of it on a rifle, four steps out, less the four steps. ± is the photo's."},{"id":"installed","value":8.46,"unit":"in","pm":0.12,"source":{"type":"derived","expr":"{bcm-castle-nut.rear_face_behind_pin} + {.front_behind_nut_pos3} - 2 * {bcm-receiver-extension.position_step} + {.length}","via":"harvest"},"note":"Wing's photo of it on a lower, two steps out, less the two steps. ± is the photo's and the castle nut's place."},{"id":"from-ctr","value":8.476,"unit":"in","pm":0.12,"source":{"type":"derived","expr":"{magpul-ctr.butt_behind_pin_pos1} - ({.review_ctr_lop_collapsed} - {.lop_collapsed})","via":"harvest"},"note":"One reviewer's collapsed lengths of pull for the CTR and for this stock, taken off the CTR's measured seat. ± is that seat's, and two figures of unstated method."},{"id":"holes","value":8.549,"unit":"in","pm":0.1,"source":{"type":"derived","expr":"{bcm-receiver-extension.tube_front_behind_pin} + {bcm-receiver-extension.tube_length} - {bcm-receiver-extension.position_hole_rear_from_rear} - 5 * {bcm-receiver-extension.position_step} - {.lock_pin_behind_front} + {.length}","via":"harvest"},"note":"The lock pin (on the patent's section) in the tube's front hole. ± for the hole's place (0.03), the tube's seat (0.02), the pin's place in a drawing that isn't held to scale (0.04) and the tube's length, which is a generic figure."},{"id":"tube-rear","value":8.687,"unit":"in","pm":0.1,"source":{"type":"derived","expr":"{bcm-receiver-extension.tube_front_behind_pin} + {bcm-receiver-extension.tube_length} + {.butt_behind_tube_rear_pos1}","via":"harvest"},"note":"The tube's rear face against the stock's end wall, as the section draws it collapsed. ± for the tube's length (generic) and the drawing."}],"adopt":{"from":"installed-rifle","reason":"Measured on a photo of the stock on a rifle between the receiver's pins. A second photo, on another lower, and a reviewer's lengths of pull agree within 0.05 in; the lock pin in the tube's front hole within the two ±. The tube's rear end against the stock's end wall, read on the patent's section with a generic tube's length, is 0.26 in more and stays in view."},"note":"Five ways to it. BCM's brochure has the stock on a rifle from the side, four steps out, with the receiver's pins in view: that is the seat, less the four steps. Wing's close photo of it on a lower, two steps out, by the tube that shows between the stock and the castle nut, agrees within 0.04 in; so does a reviewer's pair of lengths of pull for this stock and the Magpul CTR, whose seat is measured. Two more go through BCM's patent section, which draws the stock collapsed: the lock pin in the tube's front pocket (0.12 in more) and the tube's rear face against the stock's end wall (0.26 in more, outside the two ±): both rest on a generic tube's length and holes and on a drawing that isn't held to scale. Collapsed, the stock's front stands 0.10 in behind the castle nut (bcm-castle-nut.rear_face_behind_pin), clear of it."},"butt_behind_pin_pos5":{"label":"Butt behind the takedown pin as BCM photographed it: four steps out (position 5)","kind":"length","measurements":[{"id":"installed-rifle","value":11.067,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/bcm-stock-mod-0 824d597175f5 (BCM, MOD 0 STOCK SERIES brochure, page 3: a rifle with the Flat Dark Earth stock, straight right side, 1280 x 800)","scaleRef":"frame from the receiver's pins on its right side: the selector (437.4, 403.6), the trigger pin (475.3, 410.2) and the hammer pin (503.7, 400.1) stand 33.69 px/in apart by std.ar15.selector_x, trigger_pin_x and hammer_pin_x (the three pairs agree to 0.01) and put the takedown pin at column 410.35; the pivot pin's head is at 625.5 by eye, 625.1 by that frame; the pins' heights agree with the standard within a pixel","method":"the butt's rearmost point (column 37.5, rows 348 to 356, at the 50% level against the dark ground) behind the takedown pin's column (410.35): 372.85 px; the rifle lies level within half a degree (the stock's top edge, the pins); ± for the edge, the pin's column and the scale (0.15 px/in)","via":"harvest"}}],"note":"Which position it is in: its front face stands 2.76 in behind the castle nut's place, and a stock can't pass the nut, so it is at most four steps out (4 x 0.66); three steps would leave the collapsed stock 0.78 in short of the nut, where Wing's photo, the lock pin and the reviewer's length of pull all have it within 0.25."},"review_ctr_lop_collapsed":{"label":"The Magpul CTR's collapsed length of pull in the review that gives this stock's","kind":"length","measurements":[{"id":"guns-america","value":10.5,"unit":"in","stated":"There is 3.3 inches of adjustment and the LOP ranges from 13.8 inches fully extended to 10.5 inches collapsed.","source":{"type":"spec","publisher":"review","name":"Guns America Digest, AR Stock Hack: Magpul CTR vs. BCM Gunfighter Mod 0 (Robert Sadowski, 2024-04-13)","url":"https://gunsamerica.com/digest/ar-stock-hack-magpul-ctr-vs-bcm-gunfighter-mod-0/","retrieved":"2026-10-05","via":"harvest"}}],"note":"Not this stock's: the same reviewer's figure for the CTR, kept to set his two against each other (butt_behind_pin_pos1, from-ctr). It is the figure retailers carry for the CTR."},"front_behind_nut_pos3":{"label":"The stock's front face behind the castle nut's rear face as Wing photographed it: two steps out (position 3)","kind":"length","measurements":[{"id":"installed","value":1.455,"unit":"in","pm":0.1,"source":{"type":"photo","photo":"references/bcm-stock-mod-0 26f9eba59a87 (Wing Tactical, image 6: the black stock on a lower, right side, 1280 x 1280; the rifle is turned 19 degrees in the picture and seen from a little ahead)","scaleRef":"the stock's own length along the tube's direction (the cheek's top edge, 19.3 degrees from level): 492 px from the butt's heel (97, 765) to the cheek's top front corner (566, 611) for bcm-stock-mod-0.length = 6.657 in: 73.9 px/in. Seen from 15 degrees ahead the heel's near edge would stand 0.2 in further back and the scale be 71.8","method":"along that direction, from the cheek's top front corner (566, 611) to the castle nut's rear face at its top (667, 574): 107.5 px, 1.455 in (1.50 at the other scale); ± for the two edges, 3 px each, and for the view","via":"harvest"}}],"note":"Which position it is in: collapsed, the stock's front can't be inside the nut, so the 1.46 in of tube is at most two steps (2 x 0.66); one step would leave the collapsed stock 0.8 in short of the nut, where BCM's own photo of it on a rifle has it 0.1."},"lop_collapsed":{"label":"Length of pull, collapsed (a reviewer's rifle)","kind":"length","measurements":[{"id":"guns-america","value":10.25,"unit":"in","stated":"Fully collapsed the LOP is 10.25 inches; fully extended it is 13.5 inches.","source":{"type":"spec","publisher":"review","name":"Guns America Digest, AR Stock Hack: Magpul CTR vs. BCM Gunfighter Mod 0 (Robert Sadowski, 2024-04-13)","url":"https://gunsamerica.com/digest/ar-stock-hack-magpul-ctr-vs-bcm-gunfighter-mod-0/","retrieved":"2026-10-05","via":"harvest"}}],"note":"BCM states none. A reviewer's figure on his own rifle; how it was taken isn't said. It is 1.82 in more than the seat (butt_behind_pin_pos1), where Magpul's for the MOE Carbine is 1.60 over its own: lengths of pull aren't taken one way, which is why only this reviewer's two figures are set against each other."},"lop_extended":{"label":"Length of pull, extended (a reviewer's rifle)","kind":"length","measurements":[{"id":"guns-america","value":13.5,"unit":"in","stated":"Fully collapsed the LOP is 10.25 inches; fully extended it is 13.5 inches.","source":{"type":"spec","publisher":"review","name":"Guns America Digest, AR Stock Hack: Magpul CTR vs. BCM Gunfighter Mod 0 (Robert Sadowski, 2024-04-13)","url":"https://gunsamerica.com/digest/ar-stock-hack-magpul-ctr-vs-bcm-gunfighter-mod-0/","retrieved":"2026-10-05","via":"harvest"}}],"note":"With the collapsed figure: 3.25 in over five steps, 0.65 in a step (bcm-receiver-extension.position_step is 0.66)."},"strut_rib_pitch":{"label":"The ribs across the strut's underside: their pitch along the strut","kind":"length","measurements":[{"id":"photo","value":0.0671,"unit":"in","pm":0.002,"source":{"type":"photo","photo":"references/bcm-stock-mod-0 a9e871874f14 (Primary Arms BCM-GFS-MOD-0-BLK_00.jpg, straight right side on white, 2000 x 1333)","scaleRef":"the trace's scale, 250.4 px/in (bcm-stock-mod-0.height on the outline)","method":"the strut's lower edge over rows 815 to 1130 (the part's last dark pixel in each row, to the 50% level), its teeth read off a fitted line: the period of their autocorrelation, 16.81 px (0.84 at that lag; 18 teeth)","via":"harvest"}}]},"strut_rib_depth":{"label":"The ribs across the strut's underside: how deep the grooves between them are","kind":"length","measurements":[{"id":"photo","value":0.0133,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/bcm-stock-mod-0 a9e871874f14 (Primary Arms BCM-GFS-MOD-0-BLK_00.jpg, straight right side on white, 2000 x 1333)","scaleRef":"the trace's scale, 250.4 px/in","method":"the same edge, detrended: peak to valley over each period, median 3.3 px","via":"harvest"}}],"note":"As the silhouette shows them at 250 px/in: a groove narrower than a pixel or two reads shallower than it is."},"pad_rib_pitch":{"label":"The butt pad's chevron ribs: their pitch down the pad's height","kind":"length","measurements":[{"id":"photo","value":0.115,"unit":"in","pm":0.003,"source":{"type":"photo","photo":"references/bcm-stock-mod-0 a9e871874f14 (Primary Arms BCM-GFS-MOD-0-BLK_00.jpg, straight right side on white, 2000 x 1333)","scaleRef":"the trace's scale, 250.4 px/in","method":"the pad's rear edge over rows 500 to 1230 (the first dark pixel in each row), its teeth read off a fitted line 6.9 degrees from upright: period 29.0 px along it (autocorrelation 0.79; 23 teeth), 28.8 px of height","via":"harvest"}},{"id":"patent","value":0.1239,"unit":"in","pm":0.003,"source":{"type":"photo","photo":"references/bcm-stock-mod-0 754ef4883e9b (US 9,109,855 B1, sheet 3 of 7: FIG. 3B, rear view)","scaleRef":"the figure's height = bcm-stock-mod-0.height = 4.9 in: 173.1 px/in","method":"the ribs' pairs of lines down column 2408, beside the centre line, from row 1081 to row 1552: 22 periods of 21.45 px","via":"harvest"}}],"adopt":{"from":"photo","reason":"The product's own photo. The patent's figure, which isn't held to scale, draws them 8% further apart."},"note":"The pad's face is ribbed in chevrons under a star (the patent's rear view, FIG. 3B; BCM's and Wing's photos of the pad)."},"pad_rib_depth":{"label":"The butt pad's chevron ribs: how far they stand out of the grooves between them","kind":"length","measurements":[{"id":"photo","value":0.0113,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/bcm-stock-mod-0 a9e871874f14 (Primary Arms BCM-GFS-MOD-0-BLK_00.jpg, straight right side on white, 2000 x 1333)","scaleRef":"the trace's scale, 250.4 px/in","method":"the pad's rear edge, detrended: peak to valley over each period, median 2.8 px","via":"harvest"}},{"id":"patent","value":0.0105,"unit":"in","pm":0.007,"source":{"type":"photo","photo":"references/bcm-stock-mod-0 b3de05737376 (US 9,109,855 B1, sheet 4 of 7: FIG. 4A, sectional side view)","scaleRef":"the receiver extension drawn in the stock: 152.4 px/in","method":"the pad's rear edge in the section over rows 700 to 1230 (the last dark pixel in each row), detrended: peak to valley 1.6 px","via":"harvest"}}],"adopt":{"from":"photo","reason":"The product's own photo; the patent's section reads the same within a tenth of it."},"note":"Both readings are of an edge: a rib's rounded end at the pad's side in the photo, a stroke two pixels wide in the patent's section. The ribs may stand higher at the middle of the face."},"pad_rib_angle":{"label":"The butt pad's chevron ribs: how steeply each falls from the centre line to the pad's sides","kind":"angle","measurements":[{"id":"patent","value":36.5,"unit":"deg","pm":1.5,"source":{"type":"photo","photo":"references/bcm-stock-mod-0 754ef4883e9b (US 9,109,855 B1, sheet 3 of 7: FIG. 3B, rear view)","scaleRef":"an angle: no scale","method":"the same rib line down columns 2408, 2390, 2370 and 2340 (rows 1316, 1329.5, 1344, 1366.5): 13.5 px over 18, 14.5 over 20, 22.5 over 30","via":"harvest"}}],"note":"Each rib is an inverted V: its point up on the pad's centre line, its two arms falling to the sides."},"pad_rib_top":{"label":"The butt pad's chevron ribs: the first rib's point below the pad's top","kind":"length","measurements":[{"id":"patent","value":0.83,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-stock-mod-0 754ef4883e9b (US 9,109,855 B1, sheet 3 of 7: FIG. 3B, rear view)","scaleRef":"the figure's height = bcm-stock-mod-0.height = 4.9 in: 173.1 px/in","method":"the first pair of rib lines on the centre line under the star (row 1081) below the outline's top (row 937): 144 px","via":"harvest"}}],"note":"Above it the pad's face carries BCM's star, which isn't drawn."},"wing_top_below_top":{"label":"The rear body's side wings: where each begins to stand out of the body's side, below the stock's top","kind":"length","measurements":[{"id":"side-photo","value":0.649,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/bcm-stock-mod-0 a9e871874f14 (Primary Arms BCM-GFS-MOD-0-BLK_00.jpg, straight right side on white, 2000 x 1333)","scaleRef":"the side profile's own scale: bcm-stock-mod-0.height = 4.9 in over 1227 px, 250.4 px/in","method":"the wing's upper edge, a line along the rear body (row 215 in the trace's `wing` outline; 209 to 215 on a gridded crop), below the outline's top (row 52.5): 162.5 px","via":"harvest"}},{"id":"patent","value":0.653,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/bcm-stock-mod-0 754ef4883e9b (US 9,109,855 B1, sheet 3 of 7: FIG. 3B, rear view)","scaleRef":"the figure's height = bcm-stock-mod-0.height = 4.9 in: 173.1 px/in","method":"the outermost stroke each side, row by row: the body's sides stand at columns 2284 and 2537 down to row 1050, where both begin to move out: 113 px below the outline's top (row 937)","via":"harvest"}}],"adopt":{"from":"side-photo","reason":"The product's own photo, where the wing's upper edge is a line; BCM's rear view has the ear begin within 0.004 in of it."}},"wing_widest_below_top":{"label":"The rear body's side wings: where each stands furthest out, below the stock's top","kind":"length","measurements":[{"id":"patent","value":0.976,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-stock-mod-0 754ef4883e9b (US 9,109,855 B1, sheet 3 of 7: FIG. 3B, rear view)","scaleRef":"the figure's height = bcm-stock-mod-0.height = 4.9 in: 173.1 px/in","method":"the outermost strokes are furthest apart (columns 2264 and 2556, 20 px outside the body's each side) on rows 1103 to 1109: 169 px below the outline's top (row 937)","via":"harvest"}}],"note":"How far it stands out there is the published width less the body's (bcm-stock-mod-0.width and .body_width: 0.104 in a side). The figure itself draws 20 px, 0.116 in: it is 293 px over its ears' strokes, 1.69 in, for the published 1.67. Above this height the ear's outline is a quarter round (half of its reach 0.10 in below its beginning, three quarters at 0.17, nine tenths at 0.24: rows 1067, 1079, 1091) and is drawn as one."},"wing_end_below_top":{"label":"The rear body's side wings: where each has eased back into the body's side, below the stock's top","kind":"length","measurements":[{"id":"patent","value":1.65,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/bcm-stock-mod-0 754ef4883e9b (US 9,109,855 B1, sheet 3 of 7: FIG. 3B, rear view)","scaleRef":"the figure's height = bcm-stock-mod-0.height = 4.9 in: 173.1 px/in","method":"the outermost strokes are back on the body's (columns 2283 and 2537) by row 1223, 286 px below the outline's top (row 937); they are 3 px out on row 1212 (1.59 in, the figure in body_width's note) and 4 px out on row 1205","via":"harvest"}}],"note":"Below its widest the ear's outline comes in nearly straight (17 px out on row 1133, 10 on row 1169, 4 on row 1205) and is drawn straight. The side photo has the wing's lower edge further down, 1.98 in below the top, with its arch over the QD socket: by this figure that edge is no step out of the body but the upper wall of the recessed panel under it, and the photo agrees (the wall's lit band runs round the panel's upper left corner at one width, from under the wing to the band beside the pad). What the figure can't say: below this height the pad is the widest thing in a view from behind, so the rear body's face may go on leaning in behind the pad's outline; a photo from behind the right side (9368820c28c7) has it one surface from the wing down to the panel. The model ends the ease here, at the body's side, and a crease shows there."},"qd_panel_recess_depth":{"label":"The recessed panel round the QD socket: how far its floor lies in from the body's side","kind":"length","measurements":[{"id":"assumed","value":0.05,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: a recess a page can draw (docs/research/model-detail-pass-2026-10-12.md, item 6: 'Recess depth unsourced'). Its outline is read (the side profile's `qd_panel`).","via":"harvest"}}],"note":"ASSUMED. No view on file is square across the panel and none has a shadow of known slope in it. The straight side photo (a9e871874f14) shows its walls as lit bands 15 to 26 px across (0.06 to 0.10 in): walls seen that wide in a straight side view lean or are rounded, and their width there says nothing of the depth. Drawn with square walls."},"triangle_recess_depth":{"label":"The pocket in the strut's triangle: how far its floor lies in from the body's side, each side","kind":"length","measurements":[{"id":"assumed","value":0.1,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: twice the QD panel's assumed depth, for a pocket the obliques show deeper. Its outline is read (the side profile's `triangle`).","via":"harvest"}}],"note":"ASSUMED, and likely shallow: BCM's photos of the butt from behind and below (525e4e3ca3a2) and from the front and below (b10b8afd338e) show a pocket that looks deeper than the panel round the QD socket, with a thin web between the two sides; neither is measured (no camera is fitted to them). In the straight side photo its rear wall's band is 22 px across where the QD panel's is 26, its strut wall's 13. Drawn with square walls, the floor following the body's taper to the toe."},"cheek_width":{"label":"Width of the cheek round the tube (the main body ahead of the rear body), across its sides at the tube's axis","kind":"length","measurements":[{"id":"front-photo","value":1.334,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-stock-mod-0 65b0b1c49267 (Wing Tactical, image 7: the black stock from ahead and to its right, 1280 x 1280)","scaleRef":"the bore's mouth in the same face, at std.receiver_extension.milspec_od = 1.148 in: 210 px across along the row through its widest (columns 236 to 446 on row 360, where its edges are steepest)","method":"grey levels along row 360 (a band of three): the face's left edge against the ground at column 216.5, the mouth from 236 to 446, the face's right edge, where it turns into the cheek's right side, at 460.5: 244 px of face for 210 of mouth, 1.162 times the tube's diameter; ± for a pixel at each of the four edges and the mouth's clearance (.cache/night-2026-10-19/detail/lines.py)","via":"harvest"}}],"note":"Read on the stock's front face, which the bore's mouth is cut in: the face and the mouth are one plane, so however the face is turned to the lens the two are foreshortened alike, and the face's width over the mouth's, along one row, is the cheek's over the bore's. The mouth is taken at the mil-spec tube's diameter, which the stock is made to take (BCM: 'mil-spec receiver extension'); a mouth a hundredth or two larger makes the cheek as much wider in proportion, inside the ±. In the same photo the face's top stands above the mouth's by 17 px of its 122 px radius, the axis 0.635 in under the top, where the patent's section has 0.646 (tube_axis_below_top less the rear body's step): the check. The rear body behind it, and the butt pad, are body_width (1.46 in)."}}},{"subject":"bcm-vertical-grip-mod-3-mlok","title":"BCM Vertical Grip Mod 3 (M-LOK® Compatible*), BCM-VG-MCMR-MOD-3-BLK","dimensions":{"length":{"label":"Overall length (along the handguard: the plate, end to end)","kind":"length","measurements":[{"id":"side","value":2.166,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-vertical-grip-mod-3-mlok 9b7012677b76 and 98d1613f7996 (Primary Arms BCM-VG-MCMR-MOD-3-BLK_00.jpg and _01.jpg: the grip alone on white, upright, its two sides, straight side views along the handguard, 1152 x 768)","scaleRef":"the two T-nuts' centres as std.mlok.interval (20 mm): 161.9 px in _00 (the nuts' tops 160.8, their round bosses 163.0) and 160.5 px in _01 (161.0 and 160.0); 205.6 and 203.8 px/in","method":"the silhouette's extent along the mounting face (luminance 200, sub-pixel): 448 px in _00 (2.179 in) and 438.9 px in _01 (2.153 in); the mean, the two photos' difference in the ±","via":"harvest"}},{"id":"installed","value":2.154,"unit":"in","pm":0.07,"source":{"type":"photo","photo":"references/bcm-vertical-grip-mod-3-mlok c03d3a91bf0d (BCM's BCM-VG-MCMR-MOD-3-BLK-6: the grip on a BCM MCMR handguard, from below the rifle's right side, the muzzle to the right, 1500 x 1000)","scaleRef":"std.mlok.slot_pitch (40 mm), read locally: the centroids of the see-through slots in the row beside the grip, along the handguard's axis in the picture (28.8 degrees below the horizontal): 204.5 px a pitch behind the grip and 217.3 a pitch over the two pitches ahead of it, 214.9 px interpolated at the grip's middle","method":"the plate's ends where its outline meets the handguard's lower edge, (400, 425) and (660, 563) px: 294.1 px along the axis, 1.369 pitches. The ± is the photo's: the slots' row lies a little above the plate's ends, the pitch changes 6% across the picture, and a see-through gap's middle moves along the part with the angle the line of sight crosses it at (CLAUDE.md), which the near edges would not","via":"harvest"}}],"adopt":{"from":"side","reason":"Two straight views, the smaller ±; the installed photo, scaled by the handguard's slots with nothing taken from the grip, agrees within 0.6%."},"note":"The plate on the mounting face is the grip's longest part; the body under it is 1.68 in at its crests. The two readings are independent: the installed photo is scaled by the handguard's slots, the side views by the T-nuts' spacing taken as the M-LOK interval, which the first reading confirms (lug_spacing)."},"height":{"label":"Height (how far it stands off the handguard's face: the mounting face to the base's lowest point)","kind":"length","measurements":[{"id":"photo","value":2.768,"unit":"in","pm":0.041,"source":{"type":"photo","photo":"references/bcm-vertical-grip-mod-3-mlok 9b7012677b76 (Primary Arms BCM-VG-MCMR-MOD-3-BLK_00.jpg: the grip alone on white, upright, its marked side, a straight side view along the handguard, 1152 x 768)","scaleRef":"scale from bcm-vertical-grip-mod-3-mlok.length = 2.166 in (x-extent 450 px → 207.5 px/in)","method":"height of the traced outline (tools/trace.py); the leveled outline's extent from the mounting face to the base's lowest point (its front corner), at the scale the length sets","via":"harvest"}}],"note":"Filled by the side trace (profiles.side, its targets). The base isn't parallel to the mounting face (base_angle): the grip is 0.1 in taller at one end than the other."},"width":{"label":"Width (side to side: the plate, its widest)","kind":"length","measurements":[{"id":"photo","value":1.02,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/bcm-vertical-grip-mod-3-mlok 261a5381c4b6 (BCM's BCM-VG-MCMR-MOD-3-BLK-3: the grip upright, its marked side to the lens, from about 34 degrees above, the mounting face's rim and its cells in view, 1500 x 1000)","scaleRef":"the plate's length across the picture, 479 px (474 to 953), as bcm-vertical-grip-mod-3-mlok.length","method":"the camera's elevation from the texture panel's foreshortening, a rectangle in the side face: 1.25 tall for its length here against 1.51 in the straight side view, so cos 34.3 degrees; the rim's outline across the mounting face from its far edge to its near edge 120 to 134 px down the picture (where the rim's top ends and the flare begins is a round), over sin 34.3 degrees and at the plate's scale: 0.97 to 1.08 in. The middle, the range and the lens's perspective in the ±","via":"harvest"}}],"note":"No view on file is square to the grip's end, and no page gives a width: this is read through the foreshortening of BCM's view from above, and is the least certain size on file."},"body_width":{"label":"Body width (side to side, between the flat sides under the flare)","kind":"length","measurements":[{"id":"photo","value":0.92,"unit":"in","pm":0.1,"source":{"type":"photo","photo":"references/bcm-vertical-grip-mod-3-mlok b73ab0ada049 (BCM's BCM-VG-MCMR-MOD-3-FDE-2: the Flat Dark Earth grip from above its front right corner, 1500 x 1000)","scaleRef":"a ratio: none","method":"a yawed view sees the side face as its length times cos(yaw) (295 px) and an end face as the body's width times sin(yaw) (60 px); the plate's horizontal extent (450 px) is its length times cos(yaw) plus its width times sin(yaw), and its length is 1.30 of the body's crest length (the side view): the yaw drops out and the plate is 1.108 times the body's width. Read square on (no perspective), with the corners' rounds ignored: hence the ±","via":"harvest"}}],"note":"The plate overhangs the flat sides (the flare runs all round, much less across than along). Derived from the plate's width and the ratio of the two read on one photo."},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"bcm","value":1.9,"unit":"oz","pm":0.05,"stated":"A lightweight design at 1.9 ounces.","source":{"type":"spec","publisher":"manufacturer","name":"BCM, BCM® Vertical Grip Mod 3 (M-LOK® Compatible*) - Black, Description","url":"https://bravocompanyusa.com/bcm-vertical-grip-mod-3-m-lok-compatible-black/","retrieved":"2026-10-19","via":"harvest"}},{"id":"pa","value":1.9,"unit":"oz","pm":0.05,"stated":"Weight: 1.9 oz","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, BCM GUNFIGHTER Vertical Grip Mod 3 - M-LOK - Black, Overview","url":"https://www.primaryarms.com/bcm-gunfighter-mod-3-vertical-grip-m-lok-black","retrieved":"2026-10-19","via":"harvest"}}],"adopt":{"from":"bcm","reason":"The maker's figure; the seller's is the same."},"note":"Whether BCM's figure includes the two T-nuts and screws isn't said."},"lugs":{"label":"M-LOK slots its lugs span","kind":"count","measurements":[{"id":"photo","value":1,"unit":"count","source":{"type":"derived","basis":"Two T-nuts lug_spacing apart (19.9 mm, the interval within 0.5%) fit one M-LOK slot (std.mlok.slot_length, 32 mm)","via":"harvest"}}],"note":"Its two T-nuts stand the M-LOK interval apart (lug_spacing), so both go in one 32 mm slot, one in each half of it, as the MVG's do. BCM's own photo of it on the MCMR (-6) shows something like a T-nut's head through the rear end of the slot ahead of the plate's middle, which would be the grip mounted across two slots at the interval between them; the app's index is the slot, and the positions between are a known gap."},"reach_inside":{"label":"Reach inside the handguard (below the mounting face, tightened)","kind":"length","measurements":[],"note":"Not sourced: BCM publishes no T-nut drawing, and Magpul's M-LOK FAQ says the nut's drawings are restricted. Until one is found the check against the handguard's room reads as unmade."},"lug_x":{"label":"Rear lug's centre ahead of the part's rear end","kind":"length","measurements":[{"id":"photo","value":0.688,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bcm-vertical-grip-mod-3-mlok 9b7012677b76 and 98d1613f7996 (Primary Arms _00 and _01, as above)","scaleRef":"each photo's plate extent as bcm-vertical-grip-mod-3-mlok.length","method":"the rear T-nut's centre (its top and its round boss, averaged) from the plate's rear extreme: 142.8 of 448 px in _00 and 138.7 of 438.9 in _01 (the rear end is _00's left and _01's right: the frame's front is where BCM's -6 has the muzzle); the mean of the two ratios times the length, their difference in the ±","via":"harvest"}}],"note":"The nuts are centred on the plate within 2 px in both photos: the rear one 142.8 px from the rear end in _00 and the front one 143.3 from the front end."},"lug_spacing":{"label":"Distance between the two T-nuts (centre to centre)","kind":"length","measurements":[{"id":"photo","value":0.783,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-vertical-grip-mod-3-mlok 9b7012677b76 and 98d1613f7996 (Primary Arms _00 and _01, as above)","scaleRef":"each photo's plate extent as bcm-vertical-grip-mod-3-mlok.length's installed reading (2.154 in, scaled by the MCMR's slots)","method":"the two T-nuts' centres: 161.9 of 448 px in _00 (0.778 in) and 160.5 of 438.9 px in _01 (0.788 in); the mean. The ± is the installed length's 3%","via":"harvest"}}],"note":"The check of the scale: read with the length from the installed photo (scaled by the handguard's slots), the nuts are 19.9 mm apart, the M-LOK interval (std.mlok.interval, 20 mm)."},"rake":{"label":"The body's lean from square to the mounting face (degrees)","kind":"angle","measurements":[{"id":"photo","value":5.45,"unit":"deg","pm":0.4,"source":{"type":"photo","photo":"references/bcm-vertical-grip-mod-3-mlok 9b7012677b76 and 98d1613f7996 (Primary Arms _00 and _01, as above)","scaleRef":"an angle: none","method":"lines fitted to the mounting face's silhouette (either side of the nuts) and to the crests of the two serrated edges: in _00 the face falls 3.91 degrees to the rear and the edges lean 1.6 degrees the other way, 5.5 from its normal; in _01 3.12 and 2.26, 5.4. The mean","via":"harvest"}}],"note":"BCM: \"The forward angle increases the rigidity of the forearm, while providing a more natural wrist angle. Can be mounted in reverse angle\". The body's front and rear edges (their crests) lean this far from the mounting face's normal, the base toward the end that is the rear as BCM pictures it mounted (-6). Which way BCM calls forward isn't said in words."},"base_angle":{"label":"The base's angle to the mounting face (degrees)","kind":"angle","measurements":[{"id":"photo","value":4.25,"unit":"deg","pm":0.4,"source":{"type":"photo","photo":"references/bcm-vertical-grip-mod-3-mlok 9b7012677b76 and 98d1613f7996 (Primary Arms _00 and _01, as above)","scaleRef":"an angle: none","method":"lines fitted to the mounting face's silhouette and to the base's: 4.13 degrees apart in _00 and 4.36 in _01, the front end the taller; the mean","via":"harvest"}}]},"ridges_front":{"label":"Ridges across the front end","kind":"count","measurements":[{"id":"photo","value":35,"unit":"count","source":{"type":"photo","photo":"references/bcm-vertical-grip-mod-3-mlok 9b7012677b76 and 98d1613f7996 (Primary Arms _00 and _01, as above)","scaleRef":"a count: none","method":"the front edge's silhouette row by row (luminance 200, sub-pixel), less its trend: a crest at each local maximum over 11 rows, 35 in _00 (rows 229 to 657) and 35 in _01 (244 to 661), each 11 to 15 px from the next","via":"harvest"}}]},"ridges_rear":{"label":"Ridges across the rear end","kind":"count","measurements":[{"id":"photo","value":32,"unit":"count","source":{"type":"photo","photo":"references/bcm-vertical-grip-mod-3-mlok 9b7012677b76 and 98d1613f7996 (Primary Arms _00 and _01, as above)","scaleRef":"a count: none","method":"as the front's: 24 crests found in _00 from row 262 to 649 with a run of 112 px where the edge's bend hid them, nine pitches, eight ridges, so 32; in _01 23 found from 271 to 647 with a run of 120 px, the same 32. The rear's run starts lower under its larger flare","via":"harvest"}}]},"ridge_pitch":{"label":"Ridges' pitch down the grip","kind":"length","measurements":[{"id":"photo","value":0.06,"unit":"in","pm":0.002,"source":{"type":"photo","photo":"references/bcm-vertical-grip-mod-3-mlok 9b7012677b76 and 98d1613f7996 (Primary Arms _00 and _01, as above)","scaleRef":"the side outline's scale (bcm-vertical-grip-mod-3-mlok.length over the plate's extent: 206.8 px/in in _00, 202.6 in _01)","method":"the edge profile's strongest period: 12.32 and 12.50 px at _00's two ends, 11.97 at _01's; and the front run end to end, (657 - 229) / 34 = 12.59 px. 0.060 in by both photos","via":"harvest"}}]},"ridge_first_front":{"label":"Front end: the first ridge's centre below the mounting face","kind":"length","measurements":[{"id":"photo","value":0.489,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bcm-vertical-grip-mod-3-mlok 9b7012677b76 (Primary Arms _00, as above)","scaleRef":"206.8 px/in (the side outline's)","method":"row 229, 101.2 px below the mounting face's fitted line there (perpendicular to it)","via":"harvest"}}]},"ridge_first_rear":{"label":"Rear end: the first ridge's centre below the mounting face","kind":"length","measurements":[{"id":"photo","value":0.534,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/bcm-vertical-grip-mod-3-mlok 9b7012677b76 (Primary Arms _00, as above)","scaleRef":"206.8 px/in (the side outline's)","method":"row 262, 110.5 px below the mounting face's fitted line there","via":"harvest"}}]},"groove_depth":{"label":"Grooves' depth between the ridges","kind":"length","measurements":[{"id":"photo","value":0.044,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/bcm-vertical-grip-mod-3-mlok 9b7012677b76 and 98d1613f7996 (Primary Arms _00 and _01, as above)","scaleRef":"the side outline's scale, about 205 px/in","method":"the median of each groove's depth below its neighbours' crests on the silhouette: 10.1 and 11.7 px at _00's ends, 7.6 and 8.3 at _01's; 9.4 px, the spread in the ±","via":"harvest"}}]},"groove_width":{"label":"Grooves' width (down the grip)","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the side views show ridges and grooves of about equal width at a pixel's resolution (6 px each at 205 px/in), so half the pitch.","via":"harvest"}}]},"corner_r":{"label":"Radius of the body's four upright corners (where the ends meet the flat sides)","kind":"length","measurements":[{"id":"photo","value":0.1,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-vertical-grip-mod-3-mlok 261a5381c4b6 (BCM -3, as above)","scaleRef":"the plate's length, 479 px, as bcm-vertical-grip-mod-3-mlok.length","method":"the ridges wrap round each corner onto the flat side: a band 21 px wide at each edge of the body seen square (554 to 575 and 886 to 907 px), 0.095 in","via":"harvest"}}]},"plate_corner_r":{"label":"Radius of the plate's corners, seen from above","kind":"length","measurements":[{"id":"assumed","value":0.25,"unit":"in","pm":0.08,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: BCM's views from above (-3, the FDE -2) show the rim's corners round over about a quarter of the plate's width, through a lens 34 degrees off square.","via":"harvest"}}]},"wall":{"label":"Wall round the base's opening and the rim of the mounting face","kind":"length","measurements":[{"id":"assumed","value":0.09,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the rim of the mounting face in BCM's view from above (-3) is about 20 px of the 479 px plate, 0.09 in, seen at an angle; the base's rim in its view from below (-5) looks the same.","via":"harvest"}}]},"top_cells_depth":{"label":"Depth of the cells in the mounting face","kind":"length","measurements":[{"id":"assumed","value":0.35,"unit":"in","pm":0.15,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view looks into the cells far enough to see their floors.","via":"harvest"}}]},"rib_width":{"label":"Width of the ribs between the mounting face's cells","kind":"length","measurements":[{"id":"assumed","value":0.06,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: BCM's view from above (-3) shows the ribs a little thinner than the rim.","via":"harvest"}}]},"boss_d":{"label":"Diameter of the round boss each T-nut's screw passes through, in the mounting face","kind":"length","measurements":[{"id":"photo","value":0.46,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-vertical-grip-mod-3-mlok 9b7012677b76 and 98d1613f7996 (Primary Arms _00 and _01, as above)","scaleRef":"206.8 and 202.6 px/in (the side outlines')","method":"the round bosses under the nuts, standing on the mounting face: 96 px wide in _00 (434 to 530) and 93 in _01 (446 to 539)","via":"harvest"}}]},"base_cavity_depth":{"label":"Depth of the hollow inside, from the base's opening","kind":"length","measurements":[{"id":"assumed","value":1.6,"unit":"in","pm":0.4,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: BCM's view from below (-5) shows the opening dark to the bottom of what the lens sees; the hollow is drawn up to the cells' floors less a wall.","via":"harvest"}}]},"panel_depth":{"label":"Depth of the textured panel's recess in each flat side","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the panel's border shows as a step in every view and no view sees it in profile.","via":"harvest"}}]},"panel_top":{"label":"The textured panel's top edge below the mounting face","kind":"length","measurements":[{"id":"photo","value":0.59,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-vertical-grip-mod-3-mlok 9b7012677b76 (Primary Arms _00, as above)","scaleRef":"206.8 px/in","method":"the panel's top border at row 262 against the mounting face's line at its middle, row 140: 122 px","via":"harvest"}}]},"panel_bottom":{"label":"The textured panel's bottom edge above the base","kind":"length","measurements":[{"id":"photo","value":0.24,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-vertical-grip-mod-3-mlok 9b7012677b76 (Primary Arms _00, as above)","scaleRef":"206.8 px/in","method":"the panel's bottom border at row 655 against the base at its middle, row 705: 50 px","via":"harvest"}}]},"panel_inset":{"label":"The textured panel's border in from the body's front and rear crests","kind":"length","measurements":[{"id":"photo","value":0.19,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-vertical-grip-mod-3-mlok 9b7012677b76 (Primary Arms _00, as above)","scaleRef":"206.8 px/in","method":"the panel's side borders at columns 437 and 700 against the crests' lines at 400 and 743 mid-height: 37 and 43 px; the mean","via":"harvest"}}]}}},{"subject":"blackdog-22lr-15","title":"Black Dog Machine Sonic X 15-round .22 LR magazine (the 10-round is the same body)","dimensions":{"front_to_back":{"label":"Front to back","kind":"length","measurements":[{"id":"spec","value":2.5,"unit":"in","stated":"about 2.5 in","source":{"type":"spec","publisher":"manufacturer","name":"Black Dog Machine","via":"brief"},"note":"Black Dog's figure for its other AR mags, not this model."},{"id":"lineup-smoke10","value":2.559,"unit":"in","pm":0.07,"source":{"type":"photo","photo":"references/blackdog-22lr-25 d10099a31a30 (Black Dog SMOKEANDBLACKCOLORS lineup)","scaleRef":"sibling in the same photo: smoke10 y-extent 314 px = 5.659 in (blackdog-22lr-15.overall_height, conflict)","method":"x-extent of component smoke10 (ROI [340, 132, 482, 447], central band, sampling): 142 px; ± from 1.5 px edge error at both ends plus the reference ±","via":"harvest"},"note":"The x-extent in Black Dog's lineup (spine and base lip included), scaled by this magazine's traced height. M2 scaled it by 5 in and read 2.26."},{"id":"rifle-side","value":2.51,"unit":"in","pm":0.16,"source":{"type":"photo","photo":"references/nordic-22rb-upper 990b8018ddb4 (Range Is Charm / Nordic Components: complete NC rifle, straight left side, smoke Black Dog seated; supplied in chat)","scaleRef":"top-rail slot period 7.373 px = 0.394 in (std.picatinny.slot_pitch), FFT over 360 px of rail: 18.71 px/in","method":"silhouette width 309–355 px (47 px) where the seated magazine stands clear of the lower (rows 208–220); ± is 1.5 px per translucent edge","via":"user"}},{"id":"flatlay","value":2.46,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/nordic-22rb-upper d0862b6dba98 (complete rifle lying flat on its right side, photographed straight down; supplied in chat)","scaleRef":"pin frame: takedown, pivot, trigger pin and selector (Hough-refined), 49.18 px/in, rotation 1.43°, rms 0.03 in. Phone lens distortion compresses the far right of the frame (rail slots read 3.6% small at the handguard), so only readings near the pins are used","method":"magazine span between wood-coloured pixels on nine rows below the magwell (2.40–2.46; median 2.46), with the neutral-colour mask","via":"user"}},{"id":"user-tape","value":2.514,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/blackdog-22lr-15 ffcd6aa3a249, 3cb5d7ad3c27, 9834343bf7ad (the user's own 10-round, the 15's body, lying on each side on tile, a tape on the floor beside it, from about 4 ft; 2026-10-03)","scaleRef":"the tape in each photo (170.4, 173.9 and 185.4 px/in, its 1/8 in ticks fitted to 0.11 px), brought up to the side face (0.87 in above the floor) by the lens's height: 48 to 52 in, found from lengths seen at two heights in the side and edge views (one focal length, 8940 px: 8250 to 9760), so a side face reads 1.5% large on the tape","method":"the spine rib's rear face to the front face, at the front's upper edge: 2.512, 2.518, 2.514 in the three photos; ± is the lens's height, the phone's tilt (0.25%) and the tape's own height (.cache/photos/mag, 2026-10-03)","via":"user"}}],"adopt":{"from":"user-tape","reason":"The user's own magazine beside a tape, three photos within 0.006. The seated flat-lay (2.46 ± 0.06), the Range Is Charm side view (2.51 ± 0.16) and the brief's 'about 2.5 in' agree within their ±. The lineup value is biased (M1b: lineup for height ratios only)."}},"body_height":{"label":"Body height below the feed-lip block","kind":"length","measurements":[{"id":"photo","value":5.3,"unit":"in","source":{"type":"photo","photo":"not recorded in brief","scaleRef":"not recorded in brief","method":"calibrated photo measurement","via":"brief"}},{"id":"retailer","value":5,"unit":"in","stated":"5 in","source":{"type":"spec","publisher":"retailer","name":"retailer listing (not identified in brief)","via":"brief"},"note":"Probably Black Dog's overall 5 in repeated. The brief's 5.3 in body height doesn't fit the seated magazine (see overall_height)."},{"id":"manufacturer","value":5,"unit":"in","stated":"15 Round: ... Length: 5\"","source":{"type":"spec","publisher":"manufacturer","name":"Black Dog Machine","url":"https://www.blackdogmachinellc.net/sonic-x.aspx","retrieved":"2026-09-30","via":"harvest"},"note":"Black Dog's length, read as the body below the feed-lip block: the traced 4.86 in rounds to it, and the 25-round's 7 in fits the same reading. M2 read it as the overall height."},{"id":"derived","value":4.923,"unit":"in","pm":0.034,"source":{"type":"derived","expr":"{.overall_height} - {.feed_lip_block_height}","via":"harvest"}}],"adopt":{"from":"derived","reason":"Both terms traced from the same side view. Black Dog's 5 in agrees within its rounding; the brief's 5.3 (no photo recorded) doesn't."}},"stated_length":{"label":"Length as Black Dog states it (reference points undefined)","kind":"length","measurements":[{"id":"manufacturer","value":5,"unit":"in","stated":"15 Round: ... Length: 5\"","source":{"type":"spec","publisher":"manufacturer","name":"Black Dog Machine","url":"https://www.blackdogmachinellc.net/sonic-x.aspx","retrieved":"2026-09-30","via":"harvest"},"note":"Black Dog lists 5 in for both the 10- and 15-round, and 7 in for the 25-round: the body below the feed-lip block, by the traced proportions (see body_height)."}]},"overall_height":{"label":"Overall height, feed lips to base","kind":"length","measurements":[{"id":"brief-sum","value":6.19,"unit":"in","source":{"type":"photo","photo":"not recorded in brief","scaleRef":"not recorded in brief","method":"the brief's body height 5.3 plus its feed-lip block 0.89 (body_height#photo + feed_lip_block_height#photo)","via":"brief"},"note":"From the brief's photo figures; fails the seated fit check (0.9 in above the bore)."},{"id":"trace","value":5.659,"unit":"in","pm":0.139,"source":{"type":"photo","photo":"references/blackdog-22lr-15 0eb77371d877 (Sonic X 10-round (same body as the 15), true side view, translucent smoke on white (ar15discounts))","scaleRef":"scale from blackdog-22lr-15.front_to_back = 2.46 in (median width over 0.3–0.7 of the height from the top, 519–522 px 521 px → 211.8 px/in)","method":"height of the traced outline (tools/trace.py); feed-lip top to the lowest point of the base (its rear corner), on the outline scaled by the seated front-to-back","via":"harvest"}},{"id":"user-tape","value":5.79,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/blackdog-22lr-15 ffcd6aa3a249, 3cb5d7ad3c27, 9834343bf7ad (the user's own 10-round, the 15's body, lying on each side on tile, a tape on the floor beside it, from about 4 ft; 2026-10-03)","scaleRef":"the tape in each photo (170.4, 173.9 and 185.4 px/in, its 1/8 in ticks fitted to 0.11 px), brought up to the side face (0.87 in above the floor) by the lens's height: 48 to 52 in, found from lengths seen at two heights in the side and edge views (one focal length, 8940 px: 8250 to 9760), so a side face reads 1.5% large on the tape","method":"the feed lips' top to the end of the tab under the spine rib: 5.799, 5.804, 5.794 (the lips and the tab lie at mid-thickness and read 0.5% less large than the faces)","via":"user"}}],"adopt":{"from":"user-tape","reason":"The user's own magazine beside a tape. The earlier trace of a retailer's photo, scaled by the seated front-to-back (5.659 ± 0.139), agrees within its ±; the brief's 6.19 doesn't. It read as follows before 2026-10-03: A true side view scaled by the seated magazine's pin-calibrated front-to-back. Turned square to the magwell (std.ar15.magwell_wall_lean); the black side view agrees (IoU 0.990, 5.63 in). Fitted into the user's flat-lay the outline needs no turn (−0.17 ± 0.8°) and reproduces the seated hang, base angle and scale (free fit 0.991)."},"note":"M3 (2026-09-30): Black Dog's 5 in isn't this height. Every side view of the body is 2.29–2.31 times as tall as it is front to back (both ar15discounts views, and the smoke 10 in Black Dog's own lineup), which at the seated, pin-calibrated 2.46 in is 5.66 in; the user's three-quarter photo (box pose, ±13% for its close camera) reads the body taller still (5.7 ± 0.8 in), not shorter. Black Dog's 5 in (10/15) and 7 in (25) both fit the body below the feed-lip block, so the figure moved to body_height. M2 read it as this height and passed a fit check with the feed lips under the bore; the traced magazine's feed-lip block reaches 0.17 ± 0.15 in above the brief's bore axis (see the fit check in blockout.test.ts). The brief's 6.19 (its photo figures) is still 0.5 in too tall."},"feed_lip_block_height":{"label":"Feed-lip block height","kind":"length","measurements":[{"id":"photo","value":0.89,"unit":"in","stated":"about 0.89 in","source":{"type":"photo","photo":"not recorded in brief","scaleRef":"not recorded in brief","method":"calibrated photo measurement","via":"brief"}},{"id":"trace","value":0.804,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/blackdog-22lr-15 0eb77371d877 (Sonic X 10-round (same body as the 15), true side view, translucent smoke on white (ar15discounts))","scaleRef":"scale from blackdog-22lr-15.front_to_back = 2.46 in (median width over 0.3–0.7 of the height from the top, 519–522 px 521 px → 211.8 px/in)","method":"−y_max in x [1.9, 2.3] of the traced outline (tools/trace.py); top of the feed lips to the body's top edge ahead of the block (x 1.9–2.3 in from the spine)","via":"harvest"}},{"id":"user-tape","value":0.867,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/blackdog-22lr-15 ffcd6aa3a249, 3cb5d7ad3c27, 9834343bf7ad (the user's own 10-round, the 15's body, lying on each side on tile, a tape on the floor beside it, from about 4 ft; 2026-10-03)","scaleRef":"the tape in each photo (170.4, 173.9 and 185.4 px/in, its 1/8 in ticks fitted to 0.11 px), brought up to the side face (0.87 in above the floor) by the lens's height: 48 to 52 in, found from lengths seen at two heights in the side and edge views (one focal length, 8940 px: 8250 to 9760), so a side face reads 1.5% large on the tape","method":"the feed lips' top above the body's top line ahead of the block: 0.858, 0.865, 0.878","via":"user"}}],"adopt":{"from":"user-tape","reason":"The user's own magazine beside a tape. The retailer's photo (a screwed X-Form with brass rings) reads 0.804: its block stands 0.06 lower on the same body; the brief's 0.89 has no recorded photo and is nearer this."}},"feed_lips_width":{"label":"Feed lips, across both (the top of the block)","kind":"length","measurements":[{"id":"user-tape","value":0.14,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/blackdog-22lr-15 a1cf893cda97, ab196d2f60e8 (the user's own 10-round lying on its spine, front face up, and on its front face, spine up, a tape on the floor beside it; 2026-10-03)","scaleRef":"the tape beside it brought up to the block's own height above the floor (it stands 0.8 to 2 in below the upper edge) by the lens's height, 46 to 48 in; the body in the same views reads blackdog-22lr-15.width","method":"the silhouette's width over the block's top 0.2 in: 0.11 to 0.14 in the two views","via":"user"}}]},"feed_lips_height":{"label":"Feed lips, from their top down to where the block widens","kind":"length","measurements":[{"id":"user-tape","value":0.225,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/blackdog-22lr-15 a1cf893cda97, ab196d2f60e8 (the user's own 10-round lying on its spine, front face up, and on its front face, spine up, a tape on the floor beside it; 2026-10-03)","scaleRef":"the tape beside it brought up to the block's own height above the floor (it stands 0.8 to 2 in below the upper edge) by the lens's height, 46 to 48 in; the body in the same views reads blackdog-22lr-15.width","method":"where the silhouette steps out under the lips, below their top: 0.225 to 0.24","via":"user"}}]},"feed_lip_block_top_width":{"label":"Feed-lip block, across, under the lips","kind":"length","measurements":[{"id":"user-tape","value":0.26,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/blackdog-22lr-15 a1cf893cda97, ab196d2f60e8 (the user's own 10-round lying on its spine, front face up, and on its front face, spine up, a tape on the floor beside it; 2026-10-03)","scaleRef":"the tape beside it brought up to the block's own height above the floor (it stands 0.8 to 2 in below the upper edge) by the lens's height, 46 to 48 in; the body in the same views reads blackdog-22lr-15.width","method":"the silhouette's width just under the lips (0.24 below their top): 0.25 to 0.26","via":"user"}}]},"feed_lip_block_neck_width":{"label":"Feed-lip block, across, at its neck","kind":"length","measurements":[{"id":"user-tape","value":0.396,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/blackdog-22lr-15 a1cf893cda97, ab196d2f60e8 (the user's own 10-round lying on its spine, front face up, and on its front face, spine up, a tape on the floor beside it; 2026-10-03)","scaleRef":"the tape beside it brought up to the block's own height above the floor (it stands 0.8 to 2 in below the upper edge) by the lens's height, 46 to 48 in; the body in the same views reads blackdog-22lr-15.width","method":"the silhouette's width 0.385 below the lips' top (feed_lip_block_neck_below_top), where its taper changes: 0.39","via":"user"}}]},"feed_lip_block_neck_below_top":{"label":"Feed-lip block, its neck below the lips' top","kind":"length","measurements":[{"id":"user-tape","value":0.385,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/blackdog-22lr-15 a1cf893cda97, ab196d2f60e8 (the user's own 10-round lying on its spine, front face up, and on its front face, spine up, a tape on the floor beside it; 2026-10-03)","scaleRef":"the tape beside it brought up to the block's own height above the floor (it stands 0.8 to 2 in below the upper edge) by the lens's height, 46 to 48 in; the body in the same views reads blackdog-22lr-15.width","method":"where the block's sides change slope, along the edge's own length (feed-lip top 0, the body's top line at feed_lip_block_height)","via":"user"}}]},"feed_lip_block_shoulder_width":{"label":"Feed-lip block, across, at its shoulder","kind":"length","measurements":[{"id":"user-tape","value":0.572,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/blackdog-22lr-15 a1cf893cda97, ab196d2f60e8 (the user's own 10-round lying on its spine, front face up, and on its front face, spine up, a tape on the floor beside it; 2026-10-03)","scaleRef":"the tape beside it brought up to the block's own height above the floor (it stands 0.8 to 2 in below the upper edge) by the lens's height, 46 to 48 in; the body in the same views reads blackdog-22lr-15.width","method":"the silhouette's width 0.705 below the lips' top (feed_lip_block_shoulder_below_top): 0.57","via":"user"}}]},"feed_lip_block_shoulder_below_top":{"label":"Feed-lip block, its shoulder below the lips' top","kind":"length","measurements":[{"id":"user-tape","value":0.705,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/blackdog-22lr-15 a1cf893cda97, ab196d2f60e8 (the user's own 10-round lying on its spine, front face up, and on its front face, spine up, a tape on the floor beside it; 2026-10-03)","scaleRef":"the tape beside it brought up to the block's own height above the floor (it stands 0.8 to 2 in below the upper edge) by the lens's height, 46 to 48 in; the body in the same views reads blackdog-22lr-15.width","method":"where the block's sides turn nearly upright, along the edge's own length","via":"user"}}]},"feed_lip_block_base_width":{"label":"Feed-lip block, across, where it leaves the body","kind":"length","measurements":[{"id":"user-tape","value":0.6,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/blackdog-22lr-15 a1cf893cda97, ab196d2f60e8 (the user's own 10-round lying on its spine, front face up, and on its front face, spine up, a tape on the floor beside it; 2026-10-03)","scaleRef":"the tape beside it brought up to the block's own height above the floor (it stands 0.8 to 2 in below the upper edge) by the lens's height, 46 to 48 in; the body in the same views reads blackdog-22lr-15.width","method":"the silhouette's width at the body's top face: 0.604 from the front, 0.594 from the rear; its well in the body's top face is 0.615 by the top view (c532659922ef: 382.0 of the body's 538.6 px)","via":"user"},"note":"The catalog drew the block at the body's 0.873 until 2026-10-03."}]},"feed_lip_block_bottom_below_top":{"label":"Feed-lip block, how far down inside the body it shows","kind":"length","measurements":[{"id":"user-tape","value":1.508,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/blackdog-22lr-15 ffcd6aa3a249 (the user's own 10-round lying on its left side, a tape beside it, from about 4 ft; 2026-10-03)","scaleRef":"the tape (170.4 px/in), brought up to the side face by the lens's height (52 in: the face reads 1.5% large)","method":"the black block seen through the smoke body: its lower end, picked on a gridded crop (± 0.015) and put through the photo's factor","via":"user"}}]},"feed_lip_block_rear_x":{"label":"Feed-lip block inside the body, its rear face from the spine rib's rear face","kind":"length","measurements":[{"id":"user-tape","value":0.588,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/blackdog-22lr-15 ffcd6aa3a249 (the user's own 10-round lying on its left side, a tape beside it, from about 4 ft; 2026-10-03)","scaleRef":"the tape (170.4 px/in), brought up to the side face by the lens's height (52 in: the face reads 1.5% large)","method":"the black block seen through the smoke body at 1.28 below the lips' top: its rear edge","via":"user"}}]},"feed_lip_block_front_x":{"label":"Feed-lip block inside the body, its front face from the spine rib's rear face","kind":"length","measurements":[{"id":"user-tape","value":1.155,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/blackdog-22lr-15 ffcd6aa3a249 (the user's own 10-round lying on its left side, a tape beside it, from about 4 ft; 2026-10-03)","scaleRef":"the tape (170.4 px/in), brought up to the side face by the lens's height (52 in: the face reads 1.5% large)","method":"the black block seen through the smoke body at 1.28 below the lips' top: its front edge","via":"user"}}]},"spine_rib_width":{"label":"Spine rib, across","kind":"length","measurements":[{"id":"user-tape","value":0.441,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/blackdog-22lr-15 ab196d2f60e8 (the user's own 10-round lying on its front face, spine up; 2026-10-03)","scaleRef":"the tape beside it brought up to the rib (2.47 in above the floor) by the lens's height, 46 in","method":"the rib's two walls, columns 952.3 to 1042.1 (89.8 px)","via":"user"},"note":"It runs in the well's spine slot (std.ar15.magwell_spine_slot_width, .470)."}]},"spine_rib_depth":{"label":"Spine rib, how far it stands behind the body's rear face","kind":"length","measurements":[{"id":"user-tape","value":0.15,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/blackdog-22lr-15 ffcd6aa3a249 (the user's own 10-round lying on its left side, a tape beside it, from about 4 ft; 2026-10-03)","scaleRef":"the tape (170.4 px/in), brought up to the side face by the lens's height (52 in: the face reads 1.5% large)","method":"the rib's rear face against the body's rear face above it, in the three side photos (ffcd6aa3a249, 3cb5d7ad3c27, 9834343bf7ad)","via":"user"}}]},"catch_notch_top":{"label":"Magazine catch notch (left side), its upper edge below the feed lips' top","kind":"length","measurements":[{"id":"user-tape","value":1.44,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/blackdog-22lr-15 3cb5d7ad3c27 (the user's own 10-round lying on its right side, its left side up, a tape beside it, from about 4 ft; 2026-10-03)","scaleRef":"the tape (173.9 px/in), brought up to the side face by the lens's height (51 in: the face reads 1.5% large)","method":"the notch's rear upper corner at (0.481, -1.437) in the magazine's frame, picked on a gridded crop (± 0.015) and put through the photo's factor","via":"user"},"note":"Where the magazine hangs on the lower's catch: with std.ar15.mag_catch_slot_* it gives the seat's height (bad-workhorse-lower.magazine_seat_y)."}]},"catch_notch_height":{"label":"Magazine catch notch (left side), its height","kind":"length","measurements":[{"id":"user-tape","value":0.3,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/blackdog-22lr-15 3cb5d7ad3c27 (the user's own 10-round lying on its right side, its left side up, a tape beside it, from about 4 ft; 2026-10-03)","scaleRef":"the tape (173.9 px/in), brought up to the side face by the lens's height (51 in: the face reads 1.5% large)","method":"its upper edge at -1.437, its lower at -1.738","via":"user"}}]},"catch_notch_rear_x":{"label":"Magazine catch notch (left side), its rear end from the spine rib's rear face","kind":"length","measurements":[{"id":"user-tape","value":0.481,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/blackdog-22lr-15 3cb5d7ad3c27 (the user's own 10-round lying on its right side, its left side up, a tape beside it, from about 4 ft; 2026-10-03)","scaleRef":"the tape (173.9 px/in), brought up to the side face by the lens's height (51 in: the face reads 1.5% large)","method":"the notch's rear upper corner at (0.481, -1.437)","via":"user"}}]},"catch_notch_front_x":{"label":"Magazine catch notch (left side), its front end from the spine rib's rear face","kind":"length","measurements":[{"id":"user-tape","value":1.048,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/blackdog-22lr-15 3cb5d7ad3c27 (the user's own 10-round lying on its right side, its left side up, a tape beside it, from about 4 ft; 2026-10-03)","scaleRef":"the tape (173.9 px/in), brought up to the side face by the lens's height (51 in: the face reads 1.5% large)","method":"the notch's front lower corner at (1.048, -1.738)","via":"user"}}]},"boss_diameter":{"label":"Weld boss, its dark disc across (six of them, seen through each side wall)","kind":"length","measurements":[{"id":"user-photo","value":0.185,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/blackdog-22lr-15 c7b603c12fe9 (the user's own 10-round lying on its left side, its marked right side up, close: from about 16 in, a tape beside it; 2026-10-03)","scaleRef":"the body itself in the same photo: its rib-to-front size reads 2.607 in at the tape's scale (253.3 px/in) and is blackdog-22lr-15.front_to_back, so the upper face is at 262.6 px/in (the lens about 16 in above it)","method":"the two front bosses' discs on the gridded close photo (.cache/mag10/grid.py): the upper 2.215 to 2.405 along and 1.02 to 1.20 down, the lower 2.24 to 2.42; the far photo has them 23 to 25 px (0.14) where its contrast drops the rim","via":"user"}}]},"boss_dimple_diameter":{"label":"Weld boss, the hole at its middle on the outside of each wall","kind":"length","measurements":[{"id":"user-photo","value":0.09,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/blackdog-22lr-15 c7b603c12fe9 (the user's own 10-round lying on its left side, its marked right side up, close: from about 16 in, a tape beside it; 2026-10-03)","scaleRef":"the body itself in the same photo: its rib-to-front size reads 2.607 in at the tape's scale (253.3 px/in) and is blackdog-22lr-15.front_to_back, so the upper face is at 262.6 px/in (the lens about 16 in above it)","method":"the dark hole inside the upper front boss's ring, 2.29 to 2.37 along; its depth isn't read","via":"user"},"note":"A few pixels across in every photo: the size of a dot, not of a hole to be gauged."}]},"post_diameter":{"label":"Round post across the body at mid-height (a dark spot from both sides), across","kind":"length","measurements":[{"id":"user-photo","value":0.19,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/blackdog-22lr-15 ffcd6aa3a249 (the user's own 10-round lying on its left side, a tape beside it, from about 4 ft; 2026-10-03)","scaleRef":"the outline's own scale in that photo (172.4 px/in: profiles.side)","method":"the dark spot at (0.92, -4.16) in the magazine's frame, 33 px across; it is at the same place in the left side's photo (3cb5d7ad3c27)","via":"user"}}]},"wall_thickness":{"label":"Side wall, its thickness","kind":"length","measurements":[{"id":"user-photo","value":0.053,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/blackdog-22lr-15 a1cf893cda97 (the user's own 10-round lying on its spine, front face up, a tape on the floor beside it; 2026-10-03)","scaleRef":"the tape beside it brought up to the front face (2.47 in above the floor) by the lens's height, 48 in: 196.7 px/in","method":"the darker strip down each side of the smoke front face, where the side wall is seen end-on: 10.5 px","via":"user"}}]},"groove_front_depth":{"label":"Wide groove down each side wall, how deep at its middle","kind":"length","measurements":[{"id":"user-photo","value":0.087,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/blackdog-22lr-15 b00a9981a4b2 (the user's own 10-round held base-on to the lens, no scale in frame; 2026-10-03)","scaleRef":"the base's own thickness in the same photo, 504.6 px for blackdog-22lr-15.width: 581 px/in (its length reads 1.2% long against the thickness: the base is tilted a little to the lens)","method":"the notch it cuts in the base's outline on the edge that has the floor behind it (the right side's): an arc 49 to 52 px inside the straight line through the edge on either side of it (.cache/mag10/edges.py, looked at over the photo); the other edge's is the same within what the hand behind it lets be seen","via":"user"},"note":"An arc of this depth over the groove's width (0.28) has a radius of about 0.16: round-bottomed, as it looks."}]},"groove_middle_depth":{"label":"Narrow groove at mid-body down each side wall, how deep","kind":"length","measurements":[{"id":"user-photo","value":0.028,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/blackdog-22lr-15 b00a9981a4b2 (the user's own 10-round held base-on to the lens, no scale in frame; 2026-10-03)","scaleRef":"the base's own thickness in the same photo, 504.6 px for blackdog-22lr-15.width: 581 px/in (its length reads 1.2% long against the thickness: the base is tilted a little to the lens)","method":"its notch in the base's outline, the right side's edge: 15 to 17 px inside the straight edge","via":"user"}}]},"groove_rear_depth":{"label":"Narrow groove near the rear down each side wall, how deep","kind":"length","measurements":[{"id":"user-photo","value":0.033,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/blackdog-22lr-15 b00a9981a4b2 (the user's own 10-round held base-on to the lens, no scale in frame; 2026-10-03)","scaleRef":"the base's own thickness in the same photo, 504.6 px for blackdog-22lr-15.width: 581 px/in (its length reads 1.2% long against the thickness: the base is tilted a little to the lens)","method":"its notch in the base's outline, the right side's edge: 19 to 20 px inside the straight edge","via":"user"}}]},"catch_recess_rear_x":{"label":"Recess above the catch notch (left side, open to the top face), its rear end from the spine rib's rear face","kind":"length","measurements":[{"id":"user-photo","value":0.51,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/blackdog-22lr-15 3cb5d7ad3c27 (the user's own 10-round lying on its right side, its left side up, a tape beside it, from about 4 ft; 2026-10-03)","scaleRef":"the tape (173.9 px/in), brought up to the side face by the lens's height (51 in: the face reads 1.5% large)","method":"the recess's rear upper corner at (0.510, -0.928) in the magazine's frame, picked on a gridded crop (± 0.015) and put through the photo's factor","via":"user"}}]},"catch_recess_front_x":{"label":"Recess above the catch notch (left side), its front end from the spine rib's rear face","kind":"length","measurements":[{"id":"user-photo","value":1.019,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/blackdog-22lr-15 3cb5d7ad3c27 (the user's own 10-round lying on its right side, its left side up, a tape beside it, from about 4 ft; 2026-10-03)","scaleRef":"the tape (173.9 px/in), brought up to the side face by the lens's height (51 in: the face reads 1.5% large)","method":"the recess's front lower corner at (1.019, -1.409)","via":"user"}}]},"catch_recess_depth":{"label":"Recess above the catch notch (left side), how far it is set in from the side face","kind":"length","measurements":[{"id":"user-photo","value":0.035,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/blackdog-22lr-15 c532659922ef (the user's own 10-round held top-on to the lens, no scale in frame; 2026-10-03)","scaleRef":"the top face's own thickness in the same photo, 538.6 px for blackdog-22lr-15.width: 620.5 px/in","method":"the top face's outline on the left side's edge: between 0.50 and 1.05 from the spine rib's rear face the edge stands 22 px inside the edge ahead of it and behind it","via":"user"}}]},"catch_lip_proud":{"label":"Lip under the catch notch (left side), how far it stands out of the side face","kind":"length","measurements":[{"id":"user-photo","value":0.026,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/blackdog-22lr-15 ab196d2f60e8 (the user's own 10-round lying on its front face, spine up, a tape on the floor beside it; 2026-10-03)","scaleRef":"the tape beside it brought up to the upper edge by the lens's height, 46 in: 202.7 px/in across","method":"the left side's silhouette steps out 5.2 px over rows 1036 to 1066, which is 1.71 to 1.86 below the feed lips' top","via":"user"},"note":"More than a centred body has room for in the Army drawing's well (std.ar15.magwell_width leaves 0.015 a side): it is level with the catch slot's lower edge within what the two readings carry, where the well's wall is cut away, or the body sits to one side. Inside the well when seated, and not seen."}]},"catch_lip_bottom":{"label":"Lip under the catch notch (left side), its lower end below the feed lips' top","kind":"length","measurements":[{"id":"user-photo","value":1.859,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/blackdog-22lr-15 ab196d2f60e8 (the user's own 10-round lying on its front face, spine up, a tape on the floor beside it; 2026-10-03)","scaleRef":"the same view along the body: 204.0 px/in","method":"row 1066, where the left silhouette comes back in to the wall","via":"user"}}]},"base_slot_width":{"label":"Keyhole slot in the base, its width (and its round end's diameter)","kind":"length","measurements":[{"id":"user-photo","value":0.4,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/blackdog-22lr-15 b00a9981a4b2 (the user's own 10-round held base-on to the lens, no scale in frame; 2026-10-03)","scaleRef":"the base's own thickness in the same photo, 504.6 px for blackdog-22lr-15.width: 581 px/in (its length reads 1.2% long against the thickness: the base is tilted a little to the lens)","method":"the slot's two long edges: 0.461 of the thickness (its round end 0.456)","via":"user"}}]},"base_slot_length":{"label":"Keyhole slot in the base, its length with its round end","kind":"length","measurements":[{"id":"user-photo","value":0.998,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/blackdog-22lr-15 b00a9981a4b2 (the user's own 10-round held base-on to the lens, no scale in frame; 2026-10-03)","scaleRef":"the base's own thickness in the same photo, 504.6 px for blackdog-22lr-15.width: 581 px/in (its length reads 1.2% long against the thickness: the base is tilted a little to the lens)","method":"from the round end's front to the square end: 1.150 of the thickness","via":"user"}}]},"base_slot_front_end_from_front":{"label":"Keyhole slot in the base, its round end's front from the body's front face","kind":"length","measurements":[{"id":"user-photo","value":0.688,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/blackdog-22lr-15 b00a9981a4b2 (the user's own 10-round held base-on to the lens, no scale in frame; 2026-10-03)","scaleRef":"the base's own thickness in the same photo, 504.6 px for blackdog-22lr-15.width: 581 px/in (its length reads 1.2% long against the thickness: the base is tilted a little to the lens)","method":"0.793 of the thickness; its square end is 0.647 from the body's rear face, and the three with the slot's length come to 2.333 against the body's 2.364","via":"user"}}]},"hang_below_magwell":{"label":"Hang below magwell bottom when seated","kind":"length","measurements":[{"id":"photo","value":2.4,"unit":"in","pm":0.2,"source":{"type":"photo","photo":"handheld photo of the seated magazine (not yet archived)","scaleRef":"not recorded in brief","method":"calibrated photo measurement","via":"brief"}},{"id":"rifle-side","value":2.35,"unit":"in","pm":0.15,"source":{"type":"photo","photo":"references/nordic-22rb-upper 990b8018ddb4 (Range Is Charm / Nordic Components: complete NC rifle, straight left side, smoke Black Dog seated; supplied in chat)","scaleRef":"top-rail slot period 7.373 px = 0.394 in (std.picatinny.slot_pitch), FFT over 360 px of rail: 18.71 px/in","method":"magwell lip (y≈192) to the magazine's bottom edge, 44 px averaged along the base (2.14 in at the front, 2.57 at the rear, where the base slopes down)","via":"user"}},{"id":"flatlay","value":2.4,"unit":"in","pm":0.1,"source":{"type":"photo","photo":"references/nordic-22rb-upper d0862b6dba98 (complete rifle lying flat on its right side, photographed straight down; supplied in chat)","scaleRef":"pin frame: takedown, pivot, trigger pin and selector (Hough-refined), 49.18 px/in, rotation 1.43°, rms 0.03 in. Phone lens distortion compresses the far right of the frame (rail slots read 3.6% small at the handguard), so only readings near the pins are used","method":"magwell lip (≈ −2.15 in) to the magazine's bottom edge near the base's centre (≈ −4.55 in); the base slopes, lowest at the rear","via":"user"}}],"adopt":{"from":"rifle-side","reason":"Rail-calibrated, with its photo on file; the flat-lay photo (≈2.4) and the brief's 2.4 ± 0.2 (photo not archived) agree."}},"capacity":{"label":"Capacity","kind":"count","measurements":[{"id":"spec","value":15,"unit":"count","stated":"Capacity: 10rd, 15rd, 25rd","source":{"type":"spec","publisher":"manufacturer","name":"Black Dog Machine","url":"https://www.blackdogmachinellc.net/sonic-x.aspx","retrieved":"2026-09-30","via":"harvest"},"note":"The 15-round option (\"15 Round- Smoke- Nylon Lip\"): the user's magazine."}]},"weight":{"label":"Weight, empty","kind":"mass","measurements":[{"id":"spec","value":3.2,"unit":"oz","stated":"15 Round: Weight: 3.2oz unloaded","source":{"type":"spec","publisher":"manufacturer","name":"Black Dog Machine","url":"https://www.blackdogmachinellc.net/sonic-x.aspx","retrieved":"2026-09-30","via":"harvest"}},{"id":"retailer","value":0.15,"unit":"lb","stated":"0.15 lbs","source":{"type":"spec","publisher":"retailer","name":"Bear Creek Arsenal","url":"https://www.bearcreekarsenal.com/black-dog-10-rd-22lr-magazine.html","retrieved":"2026-09-30","via":"harvest"},"note":"the 10-round (Black Dog: the same 3.2 oz as the 15)"},{"id":"user-scale","value":90,"unit":"g","stated":"Empty 10rd magazine is 90g","source":{"type":"caliper","date":"2026-10-05","instrument":"the user's scale (not named), their own 10-round on it, empty, as asked for on 2026-10-02 (docs/STATUS.md, the photo list's 13)","via":"user"},"note":"The user's 10-round: the 15's body (the one their photos of 2026-10-03 are of), which Black Dog gives the same 3.2 oz. 3.17 oz. No ± given: compared at half its last digit, as the upper's weight from the same scale is to the gram (1718 g)."}],"adopt":{"from":"spec","reason":"Black Dog's own figure for the 15. The user's 10-round on a scale (90 g, 3.17 oz) agrees with it; and it is the retailer's own product, the 10-round, that they weighed: 0.15 lb (68 g) isn't that magazine's weight, and is set aside."}},"width":{"label":"Body thickness (Z)","kind":"length","measurements":[{"id":"v208-endview","value":0.892,"unit":"in","pm":0.035,"source":{"type":"photo","photo":"references/blackdog-22lr-25 cd5f82c32e08 (smoke 25-round end view (supplied in chat, RifleMags): a V208's)","scaleRef":"the 25-round's overall height (blackdog-22lr-25.overall_height, 7.972 in: y-extent 840 px)","method":"the 25-round's end view at its top section (blackdog-22lr-25.width#endview-50), taken as the same cross-section","via":"user"},"note":"0.873 while the 25's height was 7.801, and adopted until 2026-10-03 (as `shared`). The photo is of Black Dog's V208, whose body may not be the Sonic X's."},{"id":"box34","value":0.998,"unit":"in","pm":0.136,"source":{"type":"photo","photo":"references/blackdog-22lr-15 b6923abd4238 (smoke magazine, three-quarter view (supplied in chat))","scaleRef":"box pose from edges bottom_T, bottom_D, left_V, right_V, top_D (orthographic; parallel-edge spread 0.09°, 2.68°); D = 2.460 in (blackdog-22lr-15.front_to_back, conflict)","method":"T/D = 0.406 from the 3-edge orthographic pose (tools/box_pose.py); ± 13% on the ratio (edge fits, rounded corners) plus the reference ±","via":"user"},"note":"Thickness at the body (ribs included in the silhouette). A 10/15-round (same form factor); the cross-section is shared with the 25-round."},{"id":"user-tape","value":0.868,"unit":"in","pm":0.007,"source":{"type":"photo","photo":"references/blackdog-22lr-15 a1cf893cda97, ab196d2f60e8, c532659922ef (the user's own 10-round lying on its spine, on its front face, and seen straight down on its top; 2026-10-03)","scaleRef":"the tape beside it, brought up to the upper edge (2.3 to 2.5 in above the floor: 5.0 to 5.2% large) by the lens's height (46 to 48 in); and, without the tape, the width against that edge's own length from the side photos, and against the body's front-to-back in the top view","method":"between the side walls' outer faces (the far side face, seen obliquely as a pale strip, left out): 0.8685 and 0.8682 by the tape, 0.8687 and 0.8646 by the edge's length, 0.8682 in the top view. They share the side photos' scale. ± is the lens's height, the landmarks' rounding and the wall band's end (.cache/photos/mag, 2026-10-03)","via":"user"}}],"adopt":{"from":"user-tape","reason":"The user's own magazine, five routes within 0.004 in, inside the TDP magwell's 0.898. The 25-round's end view (0.89, a V208) and the box pose agree within their ±. Before 2026-10-03: The end view measures thickness directly against the magazine's own height; the three-quarter photo needs a pose solve with a close camera (vertical edges converge 2.7°). They agree within the pose's ± since the 25's height was re-traced (M3), and both sit under the TDP magwell's 0.898 in (the pose's lower half)."},"note":"No published value (two discovery passes, 2026-09-30). Measured from two user-supplied photos: the 25-round's straight-on end view (direct; it turned out to show Black Dog's V208, see blackdog-22lr-25.width), and a three-quarter view of a 10/15-round (box pose, perspective-limited). The 10/15 and 25 share the body cross-section, which fits the AR-15 magwell (the lower is 1.5 in across outside). M3: the TDP magwell is 0.898 in inside (std.ar15.magwell_width), an upper bound for the top section."},"base_angle":{"label":"Base plate angle (rises toward the front, seated)","kind":"angle","measurements":[{"id":"flatlay","value":9.4,"unit":"deg","pm":1.2,"source":{"type":"photo","photo":"references/nordic-22rb-upper d0862b6dba98 (complete rifle lying flat, straight down; supplied in chat)","scaleRef":"pin frame (4 points, rms 0.03 in), rotation 1.43°","method":"base edge corners picked on a 5× grid, rear (826, 993) to front (947, 976): 8.0° in the image + the frame rotation","via":"user"}},{"id":"rifle-side","value":9.7,"unit":"deg","pm":3,"source":{"type":"photo","photo":"references/nordic-22rb-upper 990b8018ddb4 (Range Is Charm complete rifle, left side; supplied in chat)","scaleRef":"rail slot period, 18.71 px/in","method":"hang at the front (2.14 in) and rear (2.57 in) over the 2.51 in front-to-back","via":"user"}},{"id":"user-tape","value":9.9,"unit":"deg","pm":0.3,"source":{"type":"photo","photo":"references/blackdog-22lr-15 ffcd6aa3a249, 3cb5d7ad3c27, 9834343bf7ad (the user's own 10-round on each side, 2026-10-03)","scaleRef":"none needed: an angle within the outline, the front face square","method":"the base, a straight line fitted to 0.2 to 0.3 px, against the front face's normal: 9.79 to 10.06 in the three far photos (10.07 and 10.30 in the two close ones)","via":"user"}}],"adopt":{"from":"user-tape","reason":"The magazine itself, its base a straight line in three photos; the seated flat-lay (9.4 ± 1.2) and the Range Is Charm photo agree."},"note":"Pointed out by the user from the complete-rifle photos. The 25-round's base is angled differently (curved body) and isn't measured yet."}}},{"subject":"blackdog-22lr-25","title":"Black Dog Machine Sonic X 25-round .22 LR magazine","dimensions":{"overall_height":{"label":"Overall height, feed lips to base","kind":"length","measurements":[{"id":"lineup-smoke25","value":7.948,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/blackdog-22lr-25 d10099a31a30 (Black Dog SMOKEANDBLACKCOLORS lineup)","scaleRef":"sibling in the same photo: smoke10 y-extent 314 px = 5.79 in (blackdog-22lr-15.overall_height: the user's own magazine since 2026-10-03; 5.659 before)","method":"y-extent of component smoke25 (ROI [25, 30, 200, 462], central band, sampling): 431 px; ± from 1.5 px edge error at both ends plus the reference ±","via":"harvest"}},{"id":"lineup-black25","value":8.021,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/blackdog-22lr-25 d10099a31a30 (Black Dog SMOKEANDBLACKCOLORS lineup)","scaleRef":"sibling in the same photo: smoke10 y-extent 314 px = 5.79 in (blackdog-22lr-15.overall_height: the user's own magazine since 2026-10-03; 5.659 before)","method":"y-extent of component black25 (ROI [185, 20, 360, 457], central band, sampling): 435 px; ± from 1.5 px edge error at both ends plus the reference ±","via":"harvest"}},{"id":"trace","value":7.972,"unit":"in","pm":0.09,"source":{"type":"photo","photo":"references/blackdog-22lr-25 c8bd551fb5e2 (Sonic X 25-round, black, beside the smoke one, right side on white (Black Dog))","scaleRef":"scale from blackdog-22lr-25.front_to_back = 2.514 in (median width over 0.18–0.3 of the height from the top, 234–236 px 235 px → 93.5 px/in); 2.46 and 7.801 until 2026-10-03, when the top section the 15-round shares was measured on the user's own magazine","method":"height of the traced outline (tools/trace.py); feed-lip top to the lowest point of the base, on the outline scaled by the top section's front-to-back","via":"harvest"}}],"adopt":{"from":"trace","reason":"Black Dog's photo of the pair, turned until the straight top section stands square (as the magwell holds it) and scaled by that section's front-to-back, which the 15-round shares. The smoke one beside it agrees (7.88, IoU 0.947), and so do the lineup's heights scaled by the 15's height."},"note":"Seated: feed-lip top to the lowest point of the base, with the straight top section square to the bore. M2 read Black Dog's 7 in as this height (and scaled the lineup by the 10-round's 5 in); both are the bodies below the feed-lip block (see body_height)."},"body_height":{"label":"Body height below the feed-lip block","kind":"length","measurements":[{"id":"manufacturer","value":7,"unit":"in","stated":"25 Round: ... Length: 7\"","source":{"type":"spec","publisher":"manufacturer","name":"Black Dog Machine","url":"https://www.blackdogmachinellc.net/sonic-x.aspx","retrieved":"2026-09-30","via":"harvest"},"note":"Black Dog's length, read as the body below the feed-lip block, like the 15-round's 5 in (M3)."},{"id":"derived","value":7.105,"unit":"in","pm":0.09,"source":{"type":"derived","expr":"{.overall_height} - {.feed_lip_block_height}","via":"harvest"}}],"adopt":{"from":"derived","reason":"The traced height less the shared feed-lip block; Black Dog's 7 in agrees."}},"feed_lip_block_height":{"label":"Feed-lip block height","kind":"length","measurements":[{"id":"shared","value":0.867,"unit":"in","source":{"type":"derived","expr":"{blackdog-22lr-15.feed_lip_block_height}","via":"harvest"},"note":"Black Dog uses the same feed-lip block across capacities; it's identical in their lineup photo."}]},"feed_lip_block_base_width":{"label":"Feed-lip block, across, where it leaves the body","kind":"length","measurements":[{"id":"shared","value":0.6,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{blackdog-22lr-15.feed_lip_block_base_width}","via":"user"},"note":"Black Dog uses the same feed-lip block across capacities; measured on the user's own 10-round (2026-10-03)."}]},"front_to_back":{"label":"Front to back at the body top","kind":"length","measurements":[{"id":"shared","value":2.514,"unit":"in","source":{"type":"derived","expr":"{blackdog-22lr-15.front_to_back}","via":"harvest"},"note":"The body top fits the same magwell. In the lineup photo the 25's top section matches the 10's width; below it the body curves forward (traced in M3)."}]},"catch_notch_top":{"label":"Magazine catch notch (left side), its upper edge below the feed lips' top","kind":"length","measurements":[{"id":"shared-top","value":1.44,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{blackdog-22lr-15.catch_notch_top}","via":"user"}}],"note":"What seats it (its `magwell` anchor): the notch's upper edge hangs on the lower's catch. No photo of a Sonic X 25 is on file with its notch readable; Black Dog's capacities share the top section (as its feed-lip block and its magwell section are the 15's here), so the notch is taken as the 15's, read on the user's own magazine."},"hang_below_magwell":{"label":"Hang below the magwell when seated","kind":"length","measurements":[{"id":"derived","value":4.532,"unit":"in","source":{"type":"derived","expr":"{.overall_height} - ({blackdog-22lr-15.overall_height} - {blackdog-22lr-15.hang_below_magwell})","via":"harvest"},"note":"Same insertion depth as the 10-round: the mag catch sets it."}]},"capacity":{"label":"Capacity","kind":"count","measurements":[{"id":"spec","value":25,"unit":"count","stated":"Capacity: 10rd, 15rd, 25rd","source":{"type":"spec","publisher":"manufacturer","name":"Black Dog Machine","url":"https://www.blackdogmachinellc.net/sonic-x.aspx","retrieved":"2026-09-30","via":"harvest"},"note":"The 25-round option (\"25 Round- Smoke- Nylon Lip\")."}]},"weight":{"label":"Weight, empty","kind":"mass","measurements":[{"id":"spec","value":4.8,"unit":"oz","stated":"25 round weight: 4.8 oz","source":{"type":"spec","publisher":"manufacturer","name":"Black Dog Machine","url":"https://www.blackdogmachinellc.net/sonic-x.aspx","retrieved":"2026-09-30","via":"harvest"}}]},"stated_length":{"label":"Length as the manufacturer states it (reference points undefined)","kind":"length","measurements":[{"id":"spec","value":7,"unit":"in","stated":"25 round length: 7\"","source":{"type":"spec","publisher":"manufacturer","name":"Black Dog Machine","url":"https://www.blackdogmachinellc.net/sonic-x.aspx","retrieved":"2026-09-30","via":"harvest"},"note":"The body below the feed-lip block, like the 15-round's 5 in (M3); M2 read it as the overall height."}]},"width":{"label":"Body thickness (Z)","kind":"length","measurements":[{"id":"endview-all","value":0.928,"unit":"in","pm":0.026,"source":{"type":"photo","photo":"references/blackdog-22lr-25 cd5f82c32e08 (smoke 25-round end view (supplied in chat, RifleMags))","scaleRef":"known length: all y-extent 842 px = 7.972 in (blackdog-22lr-25.overall_height; 7.801 until 2026-10-03)","method":"x-extent of component all (ROI [0, 0, 396, 958], rows [0.15, 0.23] of the ROI, per-row median): 98 px; ± from 1.5 px edge error at both ends plus the reference ±","via":"user"},"note":"The harvest mask (anything 8% off white) takes in the translucent edge's blur, 2–4 px each side of ~94."},{"id":"endview-50","value":0.892,"unit":"in","pm":0.035,"source":{"type":"photo","photo":"references/blackdog-22lr-25 cd5f82c32e08 (smoke 25-round end view (supplied in chat, RifleMags))","scaleRef":"scale from blackdog-22lr-25.overall_height = 7.972 in (y-extent 840 px → 105.4 px/in; 7.801 and 0.873 until 2026-10-03)","method":"median row width in y [-1.5, -0.8] (0.883–0.921) of the traced outline (tools/trace.py); the top section just below the feed-lip block (0.8–1.5 in down), edges at the 50% level; ± covers the edges and the height's ±","via":"user"},"note":"Edges at the 50% level, as for holes (D18); the top section just below the feed-lip block, the part the magwell holds."},{"id":"shared","value":0.868,"unit":"in","pm":0.007,"source":{"type":"derived","expr":"{blackdog-22lr-15.width}","via":"user"},"note":"The Sonic X body's thickness, measured on the user's own 10-round beside a tape (2026-10-03): Black Dog's capacities share the top section the magwell holds."}],"adopt":{"from":"shared","reason":"The Sonic X body itself, measured on the user's own magazine. The end view is a V208's (see the note), scaled by a height that is the Sonic X 25's: it reads 0.89, and whether a V208's body matches isn't verified."},"note":"The end view (cd5f82c32e08) is a crop of RifleMags' product photo of Black Dog's V208 25-round, not a Sonic X (identical framing and watermark; research agent, 2026-10-01). Black Dog's V208 shares followers, base plates and springs with its Sonic Weld magazines, but whether its body matches the Sonic X's isn't verified, so this thickness holds only if they do. The 15-round shares this cross-section. It has to fit the magwell's 0.898 in (std.ar15.magwell_width): the top section does, with 0.025 in to spare, like a STANAG body. Lower down the ribs bulge to ~0.90 and the body narrows toward the base. M2 scaled the end view by the 7 in it read as the height and got 0.79."}}},{"subject":"cloud-defensive-rein","title":"Cloud Defensive REIN (the REIN 3.0: REIN 3.0-DF-S-650 BLK)","dimensions":{"weight":{"label":"Weight (with the 18650 battery; the remote switch is in it by the launch text, the mount isn't named)","kind":"mass","measurements":[{"id":"maker","value":6.91,"unit":"oz","pm":0.005,"stated":"6.91 oz Weight (W/ Battery)","source":{"type":"spec","publisher":"manufacturer","name":"Cloud Defensive, Cloud Defensive REIN (Black), Output & Specs","url":"https://clouddefensive.com/products/cloud-defensive-rein-black","retrieved":"2026-10-05","via":"harvest"}},{"id":"dirty-bird","value":6.91,"unit":"oz","pm":0.005,"stated":"REIN 3.0 weight with Remote Switch and Battery: 6.91oz","source":{"type":"spec","publisher":"retailer","name":"Dirty Bird Industries, Cloud Defensive REIN Gen 3 High Output Weapon Light (the maker's launch text)","url":"https://dirtybirdusa.com/products/cloud-defensive-rein-gen-3-high-output-weapon-light/","retrieved":"2026-10-05","via":"harvest"}}],"adopt":{"from":"maker","reason":"The maker's own page; the seller's copy of the launch text gives the same figure and says what else is in it."},"note":"The maker's figure is with the battery. The light's December 2022 launch text, as two sellers and a blog quote it, says the same figure is with the remote switch and the battery; no page says whether a mount is in it (the box held a Picatinny mount then and holds the inline M-LOK mount now). No page states the weight without the battery or the mount's own."},"length":{"label":"Overall length","kind":"length","measurements":[{"id":"maker","value":6.17,"unit":"in","pm":0.005,"stated":"6.17\" Length","source":{"type":"spec","publisher":"manufacturer","name":"Cloud Defensive, Cloud Defensive REIN (Black), Output & Specs","url":"https://clouddefensive.com/products/cloud-defensive-rein-black","retrieved":"2026-10-05","via":"harvest"}},{"id":"alexanders","value":6.17,"unit":"in","pm":0.005,"stated":"The overall length measures 6.17 inches .","source":{"type":"spec","publisher":"retailer","name":"Alexander's, Cloud Defensive REIN 3.0 1250-Lumen M-LOK Weaponlight (MPN REIN 3.0-DF-S-650 BLK)","url":"https://alexandersstore.com/product/cld-def-rein-3-0-complete-kit-blk/","retrieved":"2026-10-05","via":"harvest"}}],"adopt":{"from":"maker","reason":"The maker's own page; the seller repeats it."},"note":"No page says what the length is measured between; taken as the bezel's front face to the tail cap's rear, the remote switch and its cable left out."},"head_diameter":{"label":"Head (bezel) diameter","kind":"length","measurements":[{"id":"maker","value":1.3,"unit":"in","pm":0.05,"stated":"1.3\" Bezel Diameter","source":{"type":"spec","publisher":"manufacturer","name":"Cloud Defensive, Cloud Defensive REIN (Black), Output & Specs","url":"https://clouddefensive.com/products/cloud-defensive-rein-black","retrieved":"2026-10-05","via":"harvest"}},{"id":"alexanders","value":1.3,"unit":"in","pm":0.005,"stated":"The bezel (head) diameter is 1.30 inches .","source":{"type":"spec","publisher":"retailer","name":"Alexander's, Cloud Defensive REIN 3.0 1250-Lumen M-LOK Weaponlight (MPN REIN 3.0-DF-S-650 BLK)","url":"https://alexandersstore.com/product/cld-def-rein-3-0-complete-kit-blk/","retrieved":"2026-10-05","via":"harvest"}},{"id":"impact","value":1.3,"unit":"in","pm":0.005,"stated":"Head Diameter : 1.30\"","source":{"type":"spec","publisher":"retailer","name":"Impact Guns, Cloud Defensive REIN 3.0 Weaponlight, Black, M-Lok Mount (850016201928)","url":"https://www.impactguns.com/weapon-mounted-lights/cloud-defensive-rein-3-0-weaponlight-black-m-lok-mount-850016201928-cd2109dfsblk","retrieved":"2026-10-05","via":"harvest"}}],"adopt":{"from":"maker","reason":"The maker's own figure; the sellers' second decimal agrees with it."},"note":"The maker writes one decimal, two sellers write 1.30. Taken as the head's front section, its largest (the two sections behind it read 0.3% and 0.5% less on the photos)."},"body_diameter":{"label":"Body diameter (the plain tube between the banded grip section and the head)","kind":"length","measurements":[{"id":"lens-up","value":0.881,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/cloud-defensive-rein 07a3e75fa1b3 (Rifle Supply CLDREIN-3-0-DFS650-BLK_1_HR, the black light standing lens up on white, 2000 x 2000; a quarter turn of f23602b1d23a, pixel for pixel)","scaleRef":"the bezel's front section, 394.4 px over columns 1600 to 1840, as head_diameter (1.3 in)","method":"the tube's width as a line along the photo, 254.59 + 0.00725 u px over columns 900 to 1030 and 1060 to 1190 (rms 0.29 px), carried to the bezel's columns: the bezel is 1.4757 of it there (sd 0.0026 over 224 columns). ± covers the fit and the second photo, not the bezel's own ±","via":"harvest"}},{"id":"tail-up","value":0.883,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/cloud-defensive-rein c98419fa2bbf (Rifle Supply CLDREIN-3-0-DFS650-BLK_2_HR, the black light standing tail up on white, 2000 x 2000; a quarter turn of 582744b1629f, pixel for pixel)","scaleRef":"the bezel's front section, 394.6 px over columns 1660 to 1860, as head_diameter (1.3 in)","method":"the tube's width as a line along the photo, 278.01 - 0.00568 u px over columns 930 to 1060 and 1090 to 1215 (rms 0.26 px), carried to the bezel's columns: the bezel is 1.4726 of it there (sd 0.0014 over 201 columns)","via":"harvest"}}],"adopt":{"from":"lens-up","reason":"The photo the outline is traced from; the other, taken from the other end, reads 0.002 in more, inside both ±."},"note":"Not published. The tube against the bezel on Rifle Supply's two studio photos of the light standing, one lens up and one tail up: each is taken from above its upper end, so the end nearer the lens reads larger (the tube itself widens 0.8% along its own inch in one and narrows 0.6% in the other). In each the tube's width is fitted as a line along the photo and carried to the bezel's columns (tools/trace.py fit_tube, as its tube calibration does); read that way the two photos agree to 0.2%."},"axis_above_mount":{"label":"The body's axis above the mounting face (the inline M-LOK mount's underside, which lies on the handguard's face)","kind":"length","measurements":[{"id":"side","value":0.82,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/cloud-defensive-rein f688561ad528 (Inside Safariland REIN-LIGHT-MOUNTING-BRACKET-JASON-MOSHER-1.jpg: the light's centre section bolted to the inline mount, lying on a dark surface, seen from the side and from 18 degrees under the mount's face, 800 x 800)","scaleRef":"the plain tube's silhouette, 101.5 px across (rows 176 to 277.5 with the photo turned 8.1 degrees to level the body), as body_diameter (0.881 in): 115.2 px/in; the two T-nut screws read 0.77 in apart at that scale (the M-LOK interval is 0.787)","method":"the tube's axis (row 226.5) to the mount's top edge on the near side (row 289.75): 63.25 px, plus 5.9 px for that edge standing 0.17 in nearer the lens than the axis (the mount's underside shows 21 px of its 0.60 in width: the photo looks up at it from 17.8 degrees), over that angle's cosine: 0.630 in from the axis to the mount's top; plus the mount's thickness by the same photo (mount_thickness, 0.187 in). ± covers a pixel and a half at each edge, 3 degrees of the angle and the thickness's own ±","via":"harvest"}}],"note":"Not published. On the inline M-LOK mount that is in the box. It leaves the tail cap (0.54 in radius) 0.09 in over the mount's top and the head 0.17 in over the handguard's face."},"width":{"label":"Overall width (with its mount; the remote switch and its cable left out)","kind":"length","measurements":[{"id":"head","value":1.3,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{.head_diameter}","via":"harvest"}}],"note":"No published figure. The head is the widest thing: the mount is 0.60 in wide and the body sits 0.13 in to one side of its middle, inside the head's width (Impact Guns lists 'Width : 1.30\"', its head diameter)."},"lugs":{"label":"M-LOK slots its mount's lugs span","kind":"count","measurements":[{"id":"installed","value":1,"unit":"count","source":{"type":"photo","photo":"references/cloud-defensive-rein 32c1ced040f8 (Inside Safariland REIN-LIGHT-INSTALL-2-JASON-MOSHER-1.jpg: the mount and the light's centre section on a handguard's upper right M-LOK row, tail cap off, 800 x 800)","scaleRef":"the handguard's own M-LOK slots in the mount's row (the slot behind the mount is 120 px long: std.mlok.slot_length)","method":"the mount's two T-nut screws (columns 291 and 362) both stand over the slot that begins one web ahead of the slot behind (columns 270 to 392), centred on it; the bar ahead of them carries the light and has no nut","via":"harvest"}}],"note":"No sheet states it. The inline mount has two T-nut screws an M-LOK interval apart at its rear end, and both go into one slot."},"lug_spacing":{"label":"Distance between the mount's two T-nut screws (centre to centre)","kind":"length","measurements":[{"id":"std","value":0.7874,"unit":"in","pm":0.004,"source":{"type":"derived","expr":"{std.mlok.interval}","via":"harvest"}},{"id":"side","value":0.773,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/cloud-defensive-rein f688561ad528 (Inside Safariland REIN-LIGHT-MOUNTING-BRACKET-JASON-MOSHER-1.jpg: the light's centre section bolted to the inline mount, lying on a dark surface, seen from the side and from 18 degrees under the mount's face, 800 x 800)","scaleRef":"the plain tube's silhouette, 101.5 px across (rows 176 to 277.5 with the photo turned 8.1 degrees to level the body), as body_diameter (0.881 in): 115.2 px/in; the two T-nut screws read 0.77 in apart at that scale (the M-LOK interval is 0.787)","method":"the two T-nuts' screw shanks under the mount, 89 px apart (columns 555 and 644 of the levelled photo)","via":"harvest"}},{"id":"installed","value":0.795,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/cloud-defensive-rein 32c1ced040f8 (Inside Safariland REIN-LIGHT-INSTALL-2-JASON-MOSHER-1.jpg: the mount and the light's centre section on a handguard's upper right M-LOK row, tail cap off, 800 x 800)","scaleRef":"the slot behind the mount, 120 px long (std.mlok.slot_length, 32 mm: 3.75 px/mm), less 6% for the top rail's tooth pitch falling from that slot to the mount (a close photo): 3.51 px/mm at the screws","method":"the two screw heads' centres, 71 px apart","via":"harvest"}}],"adopt":{"from":"std","reason":"Two nuts that share one slot stand the standard's interval apart; the two photos read 0.773 and 0.795 in, either side of it and inside their ±."},"note":"The M-LOK interval, as two nuts in one slot have to be; both photos read it within their ±."},"reach_inside":{"label":"Reach inside the handguard (below the mounting face, tightened)","kind":"length","measurements":[],"note":"Not sourced: no page or sheet gives the T-nuts' height, and the one photo of them shows them hanging loose under the mount."},"lug_x":{"label":"Rear T-nut screw's centre ahead of the mount's rear end","kind":"length","measurements":[{"id":"plan","value":0.3,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/cloud-defensive-rein 3c1ea2e0e782 (Cloud Defensive Inlinemlok.jpg: the inline mount alone on white, seen from above at an angle, 1200 x 1200)","scaleRef":"an affine camera fitted to the photo (.cache/batch123/cloud-defensive-rein/plate_plan.py): the two screw pockets' rims are ellipses of 58.5 x 56.0 px with their long axes at +13 degrees (the plate is seen 17 degrees off its normal), and the pockets' centres, 238.5 px apart, are taken as the M-LOK interval apart (std.mlok.interval, 20 mm): 11.93 px/mm along the plate, 11.54 across","method":"the rear pocket's centre to the outline's rear end along the pockets' line: 8.16 mm, less 0.5 mm for the outline there being the bottom edge seen past the top (the bar's thickness at 17 degrees)","via":"harvest"}},{"id":"side","value":0.295,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/cloud-defensive-rein f688561ad528 (Inside Safariland REIN-LIGHT-MOUNTING-BRACKET-JASON-MOSHER-1.jpg: the light's centre section bolted to the inline mount, lying on a dark surface, seen from the side and from 18 degrees under the mount's face, 800 x 800)","scaleRef":"the plain tube's silhouette, 101.5 px across (rows 176 to 277.5 with the photo turned 8.1 degrees to level the body), as body_diameter (0.881 in): 115.2 px/in; the two T-nut screws read 0.77 in apart at that scale (the M-LOK interval is 0.787)","method":"the rear T-nut's screw shank (column 644) to the bar's rear end (column 678.7): 34 px","via":"harvest"}}],"adopt":{"from":"plan","reason":"Read in the plate's own plane on the maker's photo; the side photo agrees within 0.005 in."}},"mount_length":{"label":"Inline mount: overall length","kind":"length","measurements":[{"id":"plan","value":3.14,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/cloud-defensive-rein 3c1ea2e0e782 (Cloud Defensive Inlinemlok.jpg: the inline mount alone on white, seen from above at an angle, 1200 x 1200)","scaleRef":"an affine camera fitted to the photo (.cache/batch123/cloud-defensive-rein/plate_plan.py): the two screw pockets' rims are ellipses of 58.5 x 56.0 px with their long axes at +13 degrees (the plate is seen 17 degrees off its normal), and the pockets' centres, 238.5 px apart, are taken as the M-LOK interval apart (std.mlok.interval, 20 mm): 11.93 px/mm along the plate, 11.54 across","method":"the outline's two ends along the line through the pockets' centres: 79.75 mm","via":"harvest"}},{"id":"side","value":3.148,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/cloud-defensive-rein f688561ad528 (Inside Safariland REIN-LIGHT-MOUNTING-BRACKET-JASON-MOSHER-1.jpg: the light's centre section bolted to the inline mount, lying on a dark surface, seen from the side and from 18 degrees under the mount's face, 800 x 800)","scaleRef":"the plain tube's silhouette, 101.5 px across (rows 176 to 277.5 with the photo turned 8.1 degrees to level the body), as body_diameter (0.881 in): 115.2 px/in; the two T-nut screws read 0.77 in apart at that scale (the M-LOK interval is 0.787)","method":"the bar's two ends, columns 316 and 678.7 of the levelled photo: 362.7 px","via":"harvest"}}],"adopt":{"from":"plan","reason":"The maker's photo of the mount alone; the side photo, scaled by the light's tube, reads the same within 0.01 in. Two photos and two scales that share nothing."},"note":"Not published (the maker states no size for the mount)."},"mount_width":{"label":"Inline mount: width","kind":"length","measurements":[{"id":"plan","value":0.6,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/cloud-defensive-rein 3c1ea2e0e782 (Cloud Defensive Inlinemlok.jpg: the inline mount alone on white, seen from above at an angle, 1200 x 1200)","scaleRef":"an affine camera fitted to the photo (.cache/batch123/cloud-defensive-rein/plate_plan.py): the two screw pockets' rims are ellipses of 58.5 x 56.0 px with their long axes at +13 degrees (the plate is seen 17 degrees off its normal), and the pockets' centres, 238.5 px apart, are taken as the M-LOK interval apart (std.mlok.interval, 20 mm): 11.93 px/mm along the plate, 11.54 across","method":"the top face at the hole end, between the two pairs of holes: 175 px across (15.17 mm). At the T-nut end the top face is 12.5 mm between its bevels","via":"harvest"}}]},"mount_thickness":{"label":"Inline mount: thickness","kind":"length","measurements":[{"id":"side","value":0.187,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/cloud-defensive-rein f688561ad528 (Inside Safariland REIN-LIGHT-MOUNTING-BRACKET-JASON-MOSHER-1.jpg: the light's centre section bolted to the inline mount, lying on a dark surface, seen from the side and from 18 degrees under the mount's face, 800 x 800)","scaleRef":"the plain tube's silhouette, 101.5 px across (rows 176 to 277.5 with the photo turned 8.1 degrees to level the body), as body_diameter (0.881 in): 115.2 px/in; the two T-nut screws read 0.77 in apart at that scale (the M-LOK interval is 0.787)","method":"the bar's near side face between the light's two feet, rows 289.75 to 310.25 at column 415: 20.5 px, over the cosine of the 17.8 degrees the photo looks up at it from","via":"harvest"}},{"id":"plan","value":0.192,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/cloud-defensive-rein 3c1ea2e0e782 (Cloud Defensive Inlinemlok.jpg: the inline mount alone on white, seen from above at an angle, 1200 x 1200)","scaleRef":"an affine camera fitted to the photo (.cache/batch123/cloud-defensive-rein/plate_plan.py): the two screw pockets' rims are ellipses of 58.5 x 56.0 px with their long axes at +13 degrees (the plate is seen 17 degrees off its normal), and the pockets' centres, 238.5 px apart, are taken as the M-LOK interval apart (std.mlok.interval, 20 mm): 11.93 px/mm along the plate, 11.54 across","method":"the near side wall at the hole end, 17 px high in the photo: the thickness times the sine of the 16.9 degrees the plate is seen from (4.88 mm)","via":"harvest"}}],"adopt":{"from":"side","reason":"A side face seen nearly square; the plan photo's reading hangs on a small angle's sine and agrees within 0.005 in."},"note":"One thickness along its length: on the side photo its top edge is level from end to end, and the T-nut end's upper long edges are bevelled (mount_bevel)."},"mount_bevel":{"label":"Inline mount: the bevel along the T-nut end's two upper long edges","kind":"length","measurements":[{"id":"side","value":0.08,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/cloud-defensive-rein f688561ad528 (Inside Safariland REIN-LIGHT-MOUNTING-BRACKET-JASON-MOSHER-1.jpg: the light's centre section bolted to the inline mount, lying on a dark surface, seen from the side and from 18 degrees under the mount's face, 800 x 800)","scaleRef":"the plain tube's silhouette, 101.5 px across (rows 176 to 277.5 with the photo turned 8.1 degrees to level the body), as body_diameter (0.881 in): 115.2 px/in; the two T-nut screws read 0.77 in apart at that scale (the M-LOK interval is 0.787)","method":"the dark band along the top of the bar's side face from the rear end to column 503 (rows 291 to 297: 6 px), taken as a 45 degree bevel seen from 17.8 degrees under: its height over (cos - sin) of that angle. The maker's photo shows the T-nut end's top face 12.5 mm wide against 15.2 at the hole end: 1.3 mm a side if the two bevels are alike","via":"harvest"}}]},"mount_bevel_length":{"label":"Inline mount: how far the bevels run from the rear end","kind":"length","measurements":[{"id":"side","value":1.52,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/cloud-defensive-rein f688561ad528 (Inside Safariland REIN-LIGHT-MOUNTING-BRACKET-JASON-MOSHER-1.jpg: the light's centre section bolted to the inline mount, lying on a dark surface, seen from the side and from 18 degrees under the mount's face, 800 x 800)","scaleRef":"the plain tube's silhouette, 101.5 px across (rows 176 to 277.5 with the photo turned 8.1 degrees to level the body), as body_diameter (0.881 in): 115.2 px/in; the two T-nut screws read 0.77 in apart at that scale (the M-LOK interval is 0.787)","method":"the dark band's front end, a slant over columns 497 to 510, to the bar's rear end (column 678.7): 175 px","via":"harvest"}}]},"mount_rear_radius":{"label":"Inline mount: the rear end's corner radius in plan","kind":"length","measurements":[{"id":"plan","value":0.2,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/cloud-defensive-rein 3c1ea2e0e782 (Cloud Defensive Inlinemlok.jpg: the inline mount alone on white, seen from above at an angle, 1200 x 1200)","scaleRef":"an affine camera fitted to the photo (.cache/batch123/cloud-defensive-rein/plate_plan.py): the two screw pockets' rims are ellipses of 58.5 x 56.0 px with their long axes at +13 degrees (the plate is seen 17 degrees off its normal), and the pockets' centres, 238.5 px apart, are taken as the M-LOK interval apart (std.mlok.interval, 20 mm): 11.93 px/mm along the plate, 11.54 across","method":"the top face's far edge leaves its line 5 mm short of the rear tip, half the plate's width out from the middle: corners of about that radius with a short flat between them","via":"harvest"}}]},"mount_pocket_diameter":{"label":"Inline mount: the T-nut screws' pockets (diameter)","kind":"length","measurements":[{"id":"plan","value":0.384,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/cloud-defensive-rein 3c1ea2e0e782 (Cloud Defensive Inlinemlok.jpg: the inline mount alone on white, seen from above at an angle, 1200 x 1200)","scaleRef":"an affine camera fitted to the photo (.cache/batch123/cloud-defensive-rein/plate_plan.py): the two screw pockets' rims are ellipses of 58.5 x 56.0 px with their long axes at +13 degrees (the plate is seen 17 degrees off its normal), and the pockets' centres, 238.5 px apart, are taken as the M-LOK interval apart (std.mlok.interval, 20 mm): 11.93 px/mm along the plate, 11.54 across","method":"the two pockets' rims, ellipses of 58.5 px semi-major axis (unforeshortened): 117 px at 11.99 px/mm","via":"harvest"}}],"note":"Their depth isn't measured."},"mount_hole_from_lug":{"label":"Inline mount: the rearmost of its four holes for the light, ahead of the rear T-nut screw","kind":"length","measurements":[{"id":"plan","value":1.559,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/cloud-defensive-rein 3c1ea2e0e782 (Cloud Defensive Inlinemlok.jpg: the inline mount alone on white, seen from above at an angle, 1200 x 1200)","scaleRef":"an affine camera fitted to the photo (.cache/batch123/cloud-defensive-rein/plate_plan.py): the two screw pockets' rims are ellipses of 58.5 x 56.0 px with their long axes at +13 degrees (the plate is seen 17 degrees off its normal), and the pockets' centres, 238.5 px apart, are taken as the M-LOK interval apart (std.mlok.interval, 20 mm): 11.93 px/mm along the plate, 11.54 across","method":"the far row's rear hole (its opening's centre) 39.30 mm ahead of the rear pocket's centre, plus 0.3 mm for the hole's rim lying lower than the pocket's (the two are read as one plane)","via":"harvest"}},{"id":"side","value":1.554,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/cloud-defensive-rein f688561ad528 (Inside Safariland REIN-LIGHT-MOUNTING-BRACKET-JASON-MOSHER-1.jpg: the light's centre section bolted to the inline mount, lying on a dark surface, seen from the side and from 18 degrees under the mount's face, 800 x 800)","scaleRef":"the plain tube's silhouette, 101.5 px across (rows 176 to 277.5 with the photo turned 8.1 degrees to level the body), as body_diameter (0.881 in): 115.2 px/in; the two T-nut screws read 0.77 in apart at that scale (the M-LOK interval is 0.787)","method":"the rear one of the two screw heads in the mount's underside (column 465) to the rear T-nut's screw (column 644): 179 px","via":"harvest"}}],"adopt":{"from":"plan","reason":"The hole itself on the maker's photo; the screw in it on the side photo is 0.005 in off."},"note":"Four holes for the light's two screws, in two rows either side of the T-nuts' line; the maker: 'Two mounting positions allows the user to customize the fit to their setup.' The rear row is the far one in the maker's photo, to the left of the mount's middle looking toward the lens with the mount face down."},"mount_hole_spacing":{"label":"Inline mount: spacing of a row's two holes (the light's two screws)","kind":"length","measurements":[{"id":"plan","value":0.833,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/cloud-defensive-rein 3c1ea2e0e782 (Cloud Defensive Inlinemlok.jpg: the inline mount alone on white, seen from above at an angle, 1200 x 1200)","scaleRef":"an affine camera fitted to the photo (.cache/batch123/cloud-defensive-rein/plate_plan.py): the two screw pockets' rims are ellipses of 58.5 x 56.0 px with their long axes at +13 degrees (the plate is seen 17 degrees off its normal), and the pockets' centres, 238.5 px apart, are taken as the M-LOK interval apart (std.mlok.interval, 20 mm): 11.93 px/mm along the plate, 11.54 across","method":"the two rows read 21.15 and 21.18 mm between their holes' centres","via":"harvest"}},{"id":"side","value":0.868,"unit":"in","pm":0.035,"source":{"type":"photo","photo":"references/cloud-defensive-rein f688561ad528 (Inside Safariland REIN-LIGHT-MOUNTING-BRACKET-JASON-MOSHER-1.jpg: the light's centre section bolted to the inline mount, lying on a dark surface, seen from the side and from 18 degrees under the mount's face, 800 x 800)","scaleRef":"the plain tube's silhouette, 101.5 px across (rows 176 to 277.5 with the photo turned 8.1 degrees to level the body), as body_diameter (0.881 in): 115.2 px/in; the two T-nut screws read 0.77 in apart at that scale (the M-LOK interval is 0.787)","method":"the two screw heads in the mount's underside, columns 365 and 465: 100 px (seen at a grazing angle)","via":"harvest"}}],"adopt":{"from":"plan","reason":"The holes seen from above; the screw heads on the side photo are within its ±."}},"mount_row_stagger":{"label":"Inline mount: how far the second row of holes stands ahead of the first","kind":"length","measurements":[{"id":"plan","value":0.169,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/cloud-defensive-rein 3c1ea2e0e782 (Cloud Defensive Inlinemlok.jpg: the inline mount alone on white, seen from above at an angle, 1200 x 1200)","scaleRef":"an affine camera fitted to the photo (.cache/batch123/cloud-defensive-rein/plate_plan.py): the two screw pockets' rims are ellipses of 58.5 x 56.0 px with their long axes at +13 degrees (the plate is seen 17 degrees off its normal), and the pockets' centres, 238.5 px apart, are taken as the M-LOK interval apart (std.mlok.interval, 20 mm): 11.93 px/mm along the plate, 11.54 across","method":"the near row's holes 4.28 and 4.31 mm ahead of the far row's along the plate","via":"harvest"}}]},"mount_row_offset":{"label":"Inline mount: each row of holes from the T-nuts' line","kind":"length","measurements":[{"id":"plan","value":0.131,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/cloud-defensive-rein 3c1ea2e0e782 (Cloud Defensive Inlinemlok.jpg: the inline mount alone on white, seen from above at an angle, 1200 x 1200)","scaleRef":"an affine camera fitted to the photo (.cache/batch123/cloud-defensive-rein/plate_plan.py): the two screw pockets' rims are ellipses of 58.5 x 56.0 px with their long axes at +13 degrees (the plate is seen 17 degrees off its normal), and the pockets' centres, 238.5 px apart, are taken as the M-LOK interval apart (std.mlok.interval, 20 mm): 11.93 px/mm along the plate, 11.54 across","method":"the two rows 6.65 mm apart across the plate (2.9 mm one side of the pockets' line and 3.7 the other, before allowing for the holes' rims lying lower than the pockets'): half of it, the rows taken as alike either side","via":"harvest"}}],"note":"How far the light's axis sits to one side of the mount's middle: the body's two feet bolt to one row or the other."},"mount_hole_diameter":{"label":"Inline mount: its holes for the light's screws (diameter)","kind":"length","measurements":[{"id":"plan","value":0.176,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/cloud-defensive-rein 3c1ea2e0e782 (Cloud Defensive Inlinemlok.jpg: the inline mount alone on white, seen from above at an angle, 1200 x 1200)","scaleRef":"an affine camera fitted to the photo (.cache/batch123/cloud-defensive-rein/plate_plan.py): the two screw pockets' rims are ellipses of 58.5 x 56.0 px with their long axes at +13 degrees (the plate is seen 17 degrees off its normal), and the pockets' centres, 238.5 px apart, are taken as the M-LOK interval apart (std.mlok.interval, 20 mm): 11.93 px/mm along the plate, 11.54 across","method":"each hole's opening, 53 px long and 40.8 across, as its rim seen 17 degrees off square with 11 px of its far wall showing: a 54.1 px rim (4.5 mm)","via":"harvest"}}]},"tail_x":{"label":"The tail cap's rear face ahead of the mount's rear end","kind":"length","measurements":[{"id":"side","value":0.21,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/cloud-defensive-rein f688561ad528 (Inside Safariland REIN-LIGHT-MOUNTING-BRACKET-JASON-MOSHER-1.jpg: the light's centre section bolted to the inline mount, lying on a dark surface, seen from the side and from 18 degrees under the mount's face, 800 x 800)","scaleRef":"the plain tube's silhouette, 101.5 px across (rows 176 to 277.5 with the photo turned 8.1 degrees to level the body), as body_diameter (0.881 in): 115.2 px/in; the two T-nut screws read 0.77 in apart at that scale (the M-LOK interval is 0.787)","method":"the grip section's bands on the photo against the same bands on the traced outline (profiles.side): the front band's two faces are 2.983 and 2.500 in ahead of the mount's rear end and 2.787 and 2.277 in ahead of the tail cap's rear face, the rear band's front face 2.057 and 1.855: 0.196, 0.223 and 0.202 in. ± covers their spread and 1% of the photo's scale over 3 in","via":"harvest"}}],"note":"Where the light sits along its mount, on the row of holes Safariland's reviewer used (the rear one). The mount's rear end stands out behind the tail cap; the rear T-nut screw is under the tail cap's last 0.1 in."},"foot_front_x":{"label":"The light's front mounting foot: its centre ahead of the mount's rear end","kind":"length","measurements":[{"id":"side","value":2.734,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/cloud-defensive-rein f688561ad528 (Inside Safariland REIN-LIGHT-MOUNTING-BRACKET-JASON-MOSHER-1.jpg: the light's centre section bolted to the inline mount, lying on a dark surface, seen from the side and from 18 degrees under the mount's face, 800 x 800)","scaleRef":"the plain tube's silhouette, 101.5 px across (rows 176 to 277.5 with the photo turned 8.1 degrees to level the body), as body_diameter (0.881 in): 115.2 px/in; the two T-nut screws read 0.77 in apart at that scale (the M-LOK interval is 0.787)","method":"the front foot's sole, columns 345 to 382.7 of the levelled photo: its middle to the bar's rear end (column 678.7)","via":"harvest"}}],"note":"The body has two feet under its grip section (Cloud Defensive: 'the standard SCOUT mounting profile'), each centred under one of the section's two bands."},"foot_spacing":{"label":"The light's two mounting feet: centre to centre","kind":"length","measurements":[{"id":"side","value":0.929,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/cloud-defensive-rein f688561ad528 (Inside Safariland REIN-LIGHT-MOUNTING-BRACKET-JASON-MOSHER-1.jpg: the light's centre section bolted to the inline mount, lying on a dark surface, seen from the side and from 18 degrees under the mount's face, 800 x 800)","scaleRef":"the plain tube's silhouette, 101.5 px across (rows 176 to 277.5 with the photo turned 8.1 degrees to level the body), as body_diameter (0.881 in): 115.2 px/in; the two T-nut screws read 0.77 in apart at that scale (the M-LOK interval is 0.787)","method":"the two soles' middles, columns 363.8 and 470.8: 107 px. The screws that hold them are 0.833 in apart (mount_hole_spacing), each a little inboard of its foot's middle","via":"harvest"}}]},"foot_length":{"label":"The light's mounting feet: length of a sole along the body","kind":"length","measurements":[{"id":"side","value":0.325,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/cloud-defensive-rein f688561ad528 (Inside Safariland REIN-LIGHT-MOUNTING-BRACKET-JASON-MOSHER-1.jpg: the light's centre section bolted to the inline mount, lying on a dark surface, seen from the side and from 18 degrees under the mount's face, 800 x 800)","scaleRef":"the plain tube's silhouette, 101.5 px across (rows 176 to 277.5 with the photo turned 8.1 degrees to level the body), as body_diameter (0.881 in): 115.2 px/in; the two T-nut screws read 0.77 in apart at that scale (the M-LOK interval is 0.787)","method":"the two soles, 37.7 and 37 px long; each foot widens upward to its band's length where it joins the body","via":"harvest"}}],"note":"How wide a foot is across the body isn't measured: no photo on file shows the feet square from an end."},"lens_diameter":{"label":"The bezel's clear opening (the lens as it shows)","kind":"length","measurements":[{"id":"front","value":0.99,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/cloud-defensive-rein 077b7c12128b (Rifle Supply CLDREIN-3-0-DFS650-BLK_3_HR: the black light lying on white, three-quarter view from the lens end, 2000 x 2000)","scaleRef":"the bezel's own silhouette just behind the lens, 450 px across the light's axis, as head_diameter (1.3 in)","method":"the bright opening inside the bezel's rim as an ellipse: 343.8 px along its long axis, which lies square to the light's axis: 0.764 of the bezel","via":"harvest"}}]},"tail_button_diameter":{"label":"The tail cap's rubber button (diameter, on the rear face)","kind":"length","measurements":[{"id":"rear","value":0.73,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/cloud-defensive-rein bc27d295564d (Cloud Defensive ReinCoyotebrown2.jpg, the Earth Brown page: the light from behind, three-quarter view, 1600 x 1600)","scaleRef":"the tail cap itself along the same line, 225 px, as its diameter on the traced outline (1.07 in)","method":"the grey button as an ellipse, 153 px along its long axis (which lies square to the light's axis): 0.68 of the tail cap","via":"harvest"}}],"note":"The push button in the tail cap's rear face, flush in its rim; grey rubber on every colour of light."}}},{"subject":"cmmg-lower-parts-kit","title":"CMMG Lower Parts Kit, AR15 (55CA6C5)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"primary-arms","value":7,"unit":"oz","pm":0.5,"stated":"Weight 7 Oz","source":{"type":"spec","publisher":"retailer","name":"Primary Arms","url":"https://www.primaryarms.com/cmmg-complete-ar-15-lower-receiver-parts-kit-cmmg55ca6c5","retrieved":"2026-10-05","via":"harvest"},"note":"Its specification table (Brand, Color, Manufacturer, Platform, Weight)."},{"id":"ar15discounts","value":9.6,"unit":"oz","pm":0.05,"stated":"Weight 9.6 oz","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts","url":"https://ar15discounts.com/products/cmmg-ar-15-lower-parts-kit/","retrieved":"2026-10-05","via":"harvest"},"note":"Its 'Additional information' rows, beside 'Dimensions 10.95 × 1.95 × 10.08 in': the packed kit. Dirty Bird (the same owner, the same copy) has the same row."},{"id":"alexanders","value":0.6,"unit":"lb","pm":0.05,"stated":"Shipping Weight: 0.6 lbs","source":{"type":"spec","publisher":"retailer","name":"Alexander's","url":"https://alexandersstore.com/product/cmmg-lpk-556-blk/","retrieved":"2026-10-05","via":"harvest"},"note":"Labelled a shipping weight; 0.6 lb is 9.6 oz."}],"adopt":{"from":"primary-arms","reason":"The one figure not labelled or tabled as a shipping weight. No page weighs the parts themselves: weigh a kit out of its pack to settle it."},"note":"CMMG states none. Three sellers do, and two of the three figures are one figure: 9.6 oz is 0.6 lb, which Alexander's labels a shipping weight and AR15Discounts tables beside a box's size (10.95 × 1.95 × 10.08 in)."},"takedown_pin_head_d":{"label":"The takedown pin head's diameter","kind":"length","measurements":[{"id":"milspec","value":0.375,"unit":"in","source":{"type":"derived","expr":"{rise-lpk.takedown_pin_head_d}","via":"user"},"note":"The Army drawing's pin (8448584), read for the Rise kit. CMMG's kit is sold as mil-spec (Wing Tactical: 'All parts meet or exceed Mil-Spec'); CMMG's laid-out photo shows the two domed heads."}]},"takedown_pin_head_t":{"label":"The takedown pin head's thickness","kind":"length","measurements":[{"id":"milspec","value":0.09,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{rise-lpk.takedown_pin_head_t}","via":"user"},"note":"Drawing 8448584, as the Rise kit's."}]},"pivot_pin_head_d":{"label":"The pivot pin head's diameter","kind":"length","measurements":[{"id":"milspec","value":0.4,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{rise-lpk.pivot_pin_head_d}","via":"user"},"note":"Drawing 8448621, as the Rise kit's."}]},"pivot_pin_head_flat":{"label":"The pivot pin head's flat from the pin's axis","kind":"length","measurements":[{"id":"milspec","value":0.1355,"unit":"in","pm":0.0025,"source":{"type":"derived","expr":"{rise-lpk.pivot_pin_head_flat}","via":"user"},"note":"Drawing 8448621, as the Rise kit's."}]},"pivot_pin_head_t":{"label":"The pivot pin head's thickness","kind":"length","measurements":[{"id":"milspec","value":0.18,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{rise-lpk.pivot_pin_head_t}","via":"user"},"note":"Drawing 8448621, as the Rise kit's."}]},"pin_head_dome_r":{"label":"Takedown and pivot pin heads, spherical radius of the domed face","kind":"length","measurements":[{"id":"milspec","value":0.38,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{rise-lpk.pin_head_dome_r}","via":"user"},"note":"Drawings 8448584 and 8448621, as the Rise kit's."}]},"selector_hub_d":{"label":"The selector's hub diameter","kind":"length","measurements":[{"id":"milspec","value":0.48,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{rise-lpk.selector_hub_d}","via":"user"},"note":"Drawing 9381367, as the Rise kit's. CMMG's photo shows a selector of this pattern (a hub, a pointer, a serrated paddle)."}]},"selector_pointer_reach":{"label":"Selector pointer tip, from the selector's axis","kind":"length","measurements":[{"id":"milspec","value":0.34,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{rise-lpk.selector_pointer_reach}","via":"user"},"note":"Drawing 9381367, as the Rise kit's."}]},"selector_pointer_angle":{"label":"Selector pointer included angle","kind":"angle","measurements":[{"id":"milspec","value":60,"unit":"deg","pm":2,"source":{"type":"derived","expr":"{rise-lpk.selector_pointer_angle}","via":"user"},"note":"Drawing 9381367, as the Rise kit's."}]},"selector_paddle_width":{"label":"Selector paddle width","kind":"length","measurements":[{"id":"milspec","value":0.25,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{rise-lpk.selector_paddle_width}","via":"user"},"note":"Drawing 9381367, as the Rise kit's."}]},"selector_paddle_reach":{"label":"Selector paddle end, from the selector's axis","kind":"length","measurements":[{"id":"milspec","value":0.81,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{rise-lpk.selector_paddle_reach}","via":"user"},"note":"Drawing 9381367, as the Rise kit's."}]},"selector_serration_height":{"label":"Selector paddle's stepped serrations, top step to the outermost step","kind":"length","measurements":[{"id":"milspec","value":0.11,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{rise-lpk.selector_serration_height}","via":"user"},"note":"Drawing 9381367 View H, as the Rise kit's."}]},"selector_lever_t":{"label":"The selector lever's thickness","kind":"length","measurements":[{"id":"milspec","value":0.25,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{rise-lpk.selector_lever_t}","via":"user"},"note":"Drawing 9381367 View H, as the Rise kit's (missing in both until 2026-11-03)."}]},"bolt_catch_paddle_rear_x":{"label":"The bolt catch paddle's rear edge ahead of the takedown pin","kind":"length","measurements":[{"id":"milspec","value":3.11,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{rise-lpk.bolt_catch_paddle_rear_x}","via":"user"},"note":"A mil-spec bolt catch in its lower, measured in the pin frame of a complete lower's photo for the Rise kit; CMMG's own catch isn't measured."}]},"bolt_catch_paddle_front_x":{"label":"Bolt catch paddle, front edge, X","kind":"length","measurements":[{"id":"milspec","value":3.455,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{rise-lpk.bolt_catch_paddle_front_x}","via":"user"},"note":"As bolt_catch_paddle_rear_x."}]},"bolt_catch_paddle_bottom_y":{"label":"Bolt catch paddle, bottom of its serrated face, Y","kind":"length","measurements":[{"id":"milspec","value":0.306,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{rise-lpk.bolt_catch_paddle_bottom_y}","via":"user"},"note":"As bolt_catch_paddle_rear_x."}]},"bolt_catch_paddle_top_y":{"label":"Bolt catch paddle, top, Y","kind":"length","measurements":[{"id":"milspec","value":0.774,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{rise-lpk.bolt_catch_paddle_top_y}","via":"user"},"note":"As bolt_catch_paddle_rear_x."}]},"bolt_catch_t":{"label":"Bolt catch plate thickness","kind":"length","measurements":[{"id":"milspec","value":0.151,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{rise-lpk.bolt_catch_t}","via":"user"},"note":"Drawing 8448628, as the Rise kit's."}]},"magazine_release_w":{"label":"The magazine release button's width (fore and aft)","kind":"length","measurements":[{"id":"milspec","value":0.3,"unit":"in","source":{"type":"derived","expr":"{rise-lpk.magazine_release_w}","via":"user"},"note":"Drawing 8448636, as the Rise kit's. CMMG's photo shows the oval, grooved button."}]},"magazine_release_h":{"label":"The magazine release button's height","kind":"length","measurements":[{"id":"milspec","value":0.5,"unit":"in","source":{"type":"derived","expr":"{rise-lpk.magazine_release_h}","via":"user"},"note":"Drawing 8448636, as the Rise kit's."}]},"magazine_release_standoff":{"label":"How far the button stands out of the receiver's body","kind":"length","measurements":[{"id":"flush","value":0.109,"unit":"in","source":{"type":"derived","expr":"{rise-lpk.magazine_release_standoff}","via":"user"},"note":"Flush with the fence, from the body's face, as the Rise kit's (its ledger has the sentence)."}]},"grip_top_y":{"label":"The A2 grip's top face in the rifle frame, Y (level: the receiver's underside either side of its lug)","kind":"length","measurements":[{"id":"seat","value":-1.0695,"unit":"in","pm":0.0115,"source":{"type":"derived","expr":"{std.ar15.deck_y} - {std.ar15.grip_seat_below_deck}","via":"user"},"note":"The grip's top face (9349127's datum -E-) against the receiver's underside. Looked at on two pin-framed photos of rifles with A2 grips, this line drawn on each (references/rise-lpk f008e4862517, a commercial complete lower at 260 px/in, and a37f831793fa, a service M4A1 at 184; .cache/batch123/cmmg-lower-parts-kit/rise-grip-final.png, usmc-grip-final.png): the seam between receiver and grip lies along it within about 0.02. What a lower's grip_seat_y reads (the M4E1's -1.443, its silhouette's lowest at the pin) is the lug's sloped face (std.ar15.grip_lug_face_from_pin: -1.418 at the pin's X), which stands in the grip's slot, and not what the grip's top bears on (docs/STATUS.md, 'Noticed, not yet acted on'). Aero's complete lower has its own A2 grip's top registered at -1.221 (aero-m4e1-lower.grip_top_y, extrapolated from 0.3 in below where the receiver hides it); its silhouette's notch between receiver and grip is at -1.10."}]},"grip_front_x":{"label":"The A2 grip's front face (above its step) in the rifle frame, X","kind":"length","measurements":[{"id":"seat","value":1.175,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{std.ar15.receiver_rear_x} + {std.ar15.grip_lug_front_from_rear_face}","via":"user"},"note":"The grip's upright front face against the rear face of the trigger guard's ears, where the lug ends. The same two photos have the grip's front face on this line; Aero's M4E1 has its own face at 1.14 to 1.17."}]},"grip_front_face_h":{"label":"The A2 grip's front face: its top face down to the step where the front strap begins","kind":"length","measurements":[{"id":"tdp","value":1.275,"unit":"in","pm":0.005,"stated":"1.275 ±.005","source":{"type":"standard","doc":"US Army TDP drawing 9349127 (Grip, Pistol), rev J, sheet 1, frame 1 of 2 (the M16 package's PDF page 33; references/aero-m4e1-lower be585e351439): the side view, right of the front face; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"Between the top face's line and the step's (a .06 R corner at its foot): 328.7 px apart on the scan (stroke centres 2413.8 and 2742.5), 257.8 px/in. The front view's block, stated .885, is 233 px across (263 px/in), and aero-m4e1-lower's ledger reads the side view's 1.390 at 263. NOT what the side view is scaled by: scaled so, the outline is larger than the A2 grips in two pin-framed photos (a service M4A1's and a commercial lower's: grip_height's note), on both of which the step under the grip's front face is 1.21 to 1.23 below the seam, where the drawn distance falls at the size those grips are (1.22). Either the callout spans something other than what it was taken to, or grips as made are short of it; the model follows the photos, and this stays here as read."}]},"grip_rake":{"label":"The A2 grip's axis from the vertical with its top face level (its bottom further back)","kind":"angle","measurements":[{"id":"tdp","value":30,"unit":"deg","pm":1,"stated":"30° ±1°","source":{"type":"standard","doc":"US Army TDP drawing 9349127 (Grip, Pistol), rev J, sheet 1, frame 1 of 2 (PDF page 33): the side view, between the top face and the lines square to the grip's axis; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"The screw bore is at 60° (basic) to the top face (Section C-C); the bottom view looks along it. On a standard lower the top face is level, so the side outline turns by this to stand the axis up."}]},"grip_width":{"label":"The A2 grip's width over its knurl (Z)","kind":"length","measurements":[{"id":"tdp","value":1.27,"unit":"in","pm":0.02,"stated":"1.270 APPROX OVER KNURL","source":{"type":"standard","doc":"US Army TDP drawing 9349127 (Grip, Pistol), rev J, sheet 1, frame 1 of 2 (PDF page 33): the bottom view, along the grip's axis; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"The drawing's 'APPROX' taken as ± 0.02 (as aero-m4e1-lower.grip_width, the same callout). What the bottom view's trace is scaled by across."}]},"grip_body_width":{"label":"The A2 grip's top block, across (Z): what bears on the receiver","kind":"length","measurements":[{"id":"tdp","value":0.885,"unit":"in","pm":0.015,"stated":".885 ±.015","source":{"type":"standard","doc":"US Army TDP drawing 9349127 (Grip, Pistol), rev J, sheet 1, frame 1 of 2 (PDF page 33): the top view; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"The slot along it, where the receiver's lug stands, is .380 +.005 (the same view). What the front view's trace is scaled by."}]},"grip_slot_width":{"label":"The A2 grip's slot along its top, where the receiver's lug stands, width","kind":"length","measurements":[{"id":"tdp","value":0.3825,"unit":"in","pm":0.0025,"stated":".380 +.005","source":{"type":"standard","doc":"US Army TDP drawing 9349127 (Grip, Pistol), rev J, sheet 1, frame 1 of 2 (PDF page 33): the top view (-B-, the slot between the block's two walls); user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":".380 to .385: the middle. Over the receiver's .375 lug (std.ar15.grip_lug_width) that is 0.004 a side, the drawing's own fit. CMMG's article: 'You may notice the open area on the pistol grip appears to be a dovetail design. This is done intentionally for the sake of a tighter fit.' The slot's own floor and rear are in the drawing's Section C-C (frame 2), not read: the model's slot stands that 0.004 off the lug's faces all round."}]},"grip_edge_r":{"label":"The A2 grip's top block, its corners' radius","kind":"length","measurements":[{"id":"tdp","value":0.06,"unit":"in","pm":0.01,"stated":".06 ±.01 R 2 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 9349127 (Grip, Pistol), rev J, sheet 1, frame 1 of 2 (PDF page 33): the front view (the block's two upper corners; the top view and the step under the front face have the same .06 ±.01 R); user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"What the model's edges are rounded by, all over: the drawing's Section D-D leaves the exterior contour to 'sample furnished by the contractor'."}]},"grip_bottom_below_pin":{"label":"A mil-spec rifle's A2 grip, its lowest point below the pin line","kind":"length","measurements":[{"id":"usmc","value":4.923,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/rise-lpk a37f831793fa (US Marine Corps: M4A1 SOPMOD Block II, straight right side, 7607 px (public domain): its A2 grip, below the receiver)","scaleRef":"frame from the reviewed holes takedown, pivot (184.3 px/in, rms 0.000 in over 2 points)","method":"−y_min in x [-2.6, 0.4] of the traced outline (tools/trace.py)","via":"harvest"},"note":"The grip's lowest point (its front lower corner), black against the photo's light ground. ± is two pixels (0.011) and the frame's scale."}],"note":"Filled by the trace's measure of the US Marine Corps' photo of an M4A1 (tools/trace.py)."},"grip_heel_behind_pin":{"label":"A mil-spec rifle's A2 grip, its rearmost point (the heel) behind the takedown pin","kind":"length","measurements":[{"id":"usmc","value":2.109,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/rise-lpk a37f831793fa (US Marine Corps: M4A1 SOPMOD Block II, straight right side, 7607 px (public domain): its A2 grip, below the receiver)","scaleRef":"frame from the reviewed holes takedown, pivot (184.3 px/in, rms 0.000 in over 2 points)","method":"−x_min in y [-5.2, -3.6] of the traced outline (tools/trace.py)","via":"harvest"},"note":"The grip's heel, the rearmost point of its lower rear corner."}],"note":"Filled by the trace's measure of the US Marine Corps' photo of an M4A1 (tools/trace.py)."},"grip_height":{"label":"The A2 grip's height: its top face to its lowest point","kind":"length","measurements":[{"id":"usmc","value":3.8535,"unit":"in","pm":0.0315,"source":{"type":"derived","expr":"{.grip_bottom_below_pin} + {.grip_top_y}","via":"harvest"},"note":"A service M4A1's A2 grip in its pin frame (its lowest point, read on the US Marine Corps' photo) below the receiver's underside where the Army's drawing puts it (grip_top_y), on which that photo and a second (references/rise-lpk f008e4862517) have the seam. Aero's photo of its own complete lower has its A2 grip's lowest point at 4.93 ± 0.031 (aero-m4e1-lower.grip_bottom_y) against this photo's 4.923: two rifles, two photos."},{"id":"drawing","value":3.976,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/aero-m4e1-lower be585e351439 (US Army TDP drawing 9349127 (Grip, Pistol) rev J, frame 1 of 2 (the user's M16 TDP scan, PDF page 33): the side view)","scaleRef":"frame from the reviewed holes top_front, step (257.8 px/in, rms 0.000 in over 2 points)","method":"height of the traced outline (tools/trace.py)","via":"user"},"note":"The side view's top face to its lowest point, at the scale its stated 1.275 gives (257.8 px/in). The ± covers the spread of the drawing's stated sizes (258 to 263 px/in: 2%)."}],"adopt":{"from":"usmc","reason":"A real grip on a real rifle, in a pin frame, and a second rifle's photo agrees within 0.01. The drawing's side view scaled by its stated 1.275 stands 0.12 in taller than both and 0.2 in further back at the heel: laid on the two photos it is plainly too large (.cache/batch123/cmmg-lower-parts-kit/usmc-grip.png, rise-grip2.png), so the 1.275 is not the drawn distance at the size real grips are (see grip_front_face_h)."},"note":"What the side view's trace is scaled by, with grip_depth. The drawing's own stated size across the view (the front face, 1.275) scales it 3% larger than a service rifle's grip is: kept, not adopted."},"grip_depth":{"label":"The A2 grip's side outline, fore and aft (its heel to its front face)","kind":"length","measurements":[{"id":"usmc","value":3.284,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.grip_front_x} + {.grip_heel_behind_pin}","via":"harvest"},"note":"A service M4A1's A2 grip in its pin frame (its heel, read on the US Marine Corps' photo) behind the receiver's face where the Army's drawing puts it (grip_front_x), on which both photos have the grip's front face."},{"id":"drawing","value":3.491,"unit":"in","pm":0.07,"source":{"type":"photo","photo":"references/aero-m4e1-lower be585e351439 (US Army TDP drawing 9349127 (Grip, Pistol) rev J, frame 1 of 2 (the user's M16 TDP scan, PDF page 33): the side view)","scaleRef":"frame from the reviewed holes top_front, step (257.8 px/in, rms 0.000 in over 2 points)","method":"width of the traced outline (tools/trace.py)","via":"user"},"note":"The side view's heel to its front face, at the same scale."}],"adopt":{"from":"usmc","reason":"As grip_height. By this the drawing's side view is 273.7 px/in, by the height 266.0: 2.9% apart (the photo's grip leans about a degree nose-up of the drawing's, which shortens the one and lengthens the other); the trace takes their mean."}},"guard_length":{"label":"Trigger guard, overall length","kind":"length","measurements":[{"id":"tdp","value":2.09,"unit":"in","pm":0.01,"stated":"2.09","source":{"type":"standard","doc":"US Army TDP drawing 8448588 (Guard, Trigger), rev E, sheet 1 of 1 (the M16 package's PDF page 60; references/tdp p60-8448588): the side view; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"}}]},"guard_hole_spacing":{"label":"Trigger guard, its two cross holes, centre to centre","kind":"length","measurements":[{"id":"tdp","value":1.844,"unit":"in","pm":0.002,"stated":"1.844 ±.002","source":{"type":"standard","doc":"US Army TDP drawing 8448588 (Guard, Trigger), rev E, sheet 1 of 1 (PDF page 60): the side view; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"The receiver's drawing has the same 1.844 between its two guard holes, along the bore line (std.ar15.trigger_guard_hole_spacing): the guard lies level."}]},"guard_hole_from_end":{"label":"Trigger guard, the rear (roll pin) hole's centre from the rear end","kind":"length","measurements":[{"id":"tdp","value":0.125,"unit":"in","pm":0.005,"stated":".125","source":{"type":"standard","doc":"US Army TDP drawing 8448588 (Guard, Trigger), rev E, sheet 1 of 1 (PDF page 60): the side view; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"The ends are full rounds about the holes (.125 R 2 PLACES): 2.09 = .125 + 1.844 + .125 within the drawing's rounding."}]},"guard_end_height":{"label":"Trigger guard, the height of its two ends (the bosses the holes are in)","kind":"length","measurements":[{"id":"tdp","value":0.25,"unit":"in","pm":0.01,"stated":".25, 2 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 8448588 (Guard, Trigger), rev E, sheet 1 of 1 (PDF page 60): the side view; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"}}]},"guard_hole_above_bottom":{"label":"Trigger guard, the holes' centre line above its flat outer face","kind":"length","measurements":[{"id":"tdp","value":0.125,"unit":"in","pm":0.005,"stated":".125","source":{"type":"standard","doc":"US Army TDP drawing 8448588 (Guard, Trigger), rev E, sheet 1 of 1 (PDF page 60): the side view, left; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"}}]},"guard_bar_t":{"label":"Trigger guard, the bar's thickness between its ends","kind":"length","measurements":[{"id":"tdp","value":0.09,"unit":"in","pm":0.01,"stated":".09","source":{"type":"standard","doc":"US Army TDP drawing 8448588 (Guard, Trigger), rev E, sheet 1 of 1 (PDF page 60): the side view; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"}}]},"guard_end_r":{"label":"Trigger guard, the radius of its ends, about the holes","kind":"length","measurements":[{"id":"tdp","value":0.125,"unit":"in","pm":0.005,"stated":".125 R 2 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 8448588 (Guard, Trigger), rev E, sheet 1 of 1 (PDF page 60): the side view; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"}}]},"guard_fillet_r":{"label":"Trigger guard, the radius where each end runs down into the bar","kind":"length","measurements":[{"id":"tdp","value":0.25,"unit":"in","pm":0.015,"stated":".250 R ±.015","source":{"type":"standard","doc":"US Army TDP drawing 8448588 (Guard, Trigger), rev E, sheet 1 of 1 (PDF page 60): the side view; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"}}]},"guard_width":{"label":"Trigger guard, width (Z)","kind":"length","measurements":[{"id":"tdp","value":0.43,"unit":"in","pm":0.003,"stated":".430 ±.003 (-B-)","source":{"type":"standard","doc":"US Army TDP drawing 8448588 (Guard, Trigger), rev E, sheet 1 of 1 (PDF page 60): the plan view; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"Between the receiver's ears, 0.439 apart (std.ar15.trigger_guard_ear_gap)."}]},"guard_rear_hole_d":{"label":"Trigger guard, the rear (roll pin) hole's diameter","kind":"length","measurements":[{"id":"tdp","value":0.1285,"unit":"in","pm":0.001,"stated":".1275 DIA +.0020, 90° ±4° C SINK BOTH SIDES TO .17 DIA","source":{"type":"standard","doc":"US Army TDP drawing 8448588 (Guard, Trigger), rev E, sheet 1 of 1 (PDF page 60): the side view; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"The receiver's rear hole is the same .1275 +.0020 (std.ar15.trigger_guard_rear_hole_d)."}]},"guard_plunger_bore_d":{"label":"Trigger guard, the plunger's bore across its front end, diameter","kind":"length","measurements":[{"id":"tdp","value":0.1275,"unit":"in","pm":0.0025,"stated":".125 DIA +.005 THRU, .166 DIA +.004 CBORE TO DEPTH SHOWN","source":{"type":"standard","doc":"US Army TDP drawing 8448588 (Guard, Trigger), rev E, sheet 1 of 1 (PDF page 60): the plan view; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"The counterbore (.345 deep) opens on the side the plan view draws nearest the side view, and the assembly's drawing (8448587, PDF page 9) has the plunger's tip standing out of that side: the rifle's right, where the receiver's front hole is ('.125 DIA +.003 THRU THIS SIDE ONLY'). CMMG's article: 'the ball detent end on the trigger guard assembly will go on the end that is closet to the magazine well'."}]},"guard_pin_hole_d":{"label":"Trigger guard, the spring pin's hole down through its front end, diameter","kind":"length","measurements":[{"id":"tdp","value":0.0635,"unit":"in","pm":0.0015,"stated":".062 DIA +.003 THRU BOTH SIDES","source":{"type":"standard","doc":"US Army TDP drawing 8448588 (Guard, Trigger), rev E, sheet 1 of 1 (PDF page 60): the plan view; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"}}]},"guard_pin_hole_from_side":{"label":"Trigger guard, the spring pin's hole from the side away from the plunger's tip (the left)","kind":"length","measurements":[{"id":"tdp","value":0.06,"unit":"in","pm":0.003,"stated":".060 ±.003","source":{"type":"standard","doc":"US Army TDP drawing 8448588 (Guard, Trigger), rev E, sheet 1 of 1 (PDF page 60): the plan view; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"}}]},"guard_edge_break":{"label":"Trigger guard, its edges' break","kind":"length","measurements":[{"id":"tdp","value":0.01,"unit":"in","pm":0.005,"stated":"BREAK SHARP EDGES .005 +.010","source":{"type":"standard","doc":"US Army TDP drawing 8448588 (Guard, Trigger), rev E, sheet 1 of 1 (PDF page 60): note 5; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":".005 to .015: the middle."}]},"guard_front_hole_y":{"label":"Where a standard lower holds the guard's front end: its front hole, Y","kind":"length","measurements":[{"id":"level","value":-2.18,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{std.ar15.trigger_guard_rear_y}","via":"user"},"note":"The receiver's drawing chains the 1.844 between its two guard holes along the bore line and gives one height (2.18) for the rear one; the guard's own holes are 1.844 apart, so both stand at one height. The reference CAD model has the front hole's spotface at Y -2.179 (std.ar15.trigger_guard_front_spotface_floor's reading). Drawn on the same two photos as the trigger (trigger_face_x), the guard's two holes land on the real guards' bosses within about 0.02 in, and its ends' rounds and the .250 R blends lie on theirs."}]},"trigger_edge_r":{"label":"Mil-spec trigger, its fillet, edge and corner radii","kind":"length","measurements":[{"id":"tdp","value":0.031,"unit":"in","pm":0.005,"stated":"FILLET, EDGE AND CORNER RADII .031, UNLESS OTHERWISE SPECIFIED","source":{"type":"standard","doc":"US Army TDP drawing 8448592 (Trigger), rev L, sheet 1 of 1 (PDF page 43; references/aero-m4e1-lower 1dabf089edf8): note 3; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"An investment casting (note 1). Section A-A gives the blade's face its own radius across (.375 R ±.015), which isn't drawn."}]},"trigger_rest_angle":{"label":"The trigger at rest: how far it is turned about its pin from the Army drawing's side elevation (positive turns the blade forward)","kind":"angle","measurements":[{"id":"aero","value":-1,"unit":"deg","pm":0.8,"source":{"type":"derived","expr":"{aero-m4e1-lower.trigger_rest_angle}","via":"user"},"note":"Read on Aero's photo of its complete lower, a mil-spec trigger at rest in a lower with a mil-spec kit: the one reading on file. No photo of CMMG's trigger installed is on file."}]},"trigger_face_x":{"label":"The trigger's face ahead of the takedown pin (at rest in a standard lower)","kind":"length","measurements":[{"id":"outline","value":1.9735,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"The traced side elevation (profiles.trigger, drawing 8448592) turned trigger_rest_angle about its pivot and stood on the standard's trigger pin hole (std.ar15.trigger_pin_x, std.ar15.trigger_pin_y): the deepest point of the blade's front edge, where a finger lies. Recomputed from the outline by app/tests/cmmg-lower-parts-kit.test.ts.","via":"user"},"note":"Aero's complete lower reads its own at 1.964 ± 0.015 on its photo (aero-m4e1-lower.trigger_face_x). The ± here is the rest angle's (0.8° at 0.95 in below the pin) and the outline's. Drawn on two pin-framed photos of rifles with mil-spec triggers (references/rise-lpk a37f831793fa, a service M4A1, and f008e4862517; .cache/batch123/cmmg-lower-parts-kit/usmc-tg.png, rise-tg.png), the blade's front edge lies on theirs within about 0.03 in."}]}}},{"subject":"cmmg-safety-selector","title":"CMMG Safety Selector, AR15","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"metal","value":0.654,"unit":"oz","pm":0.07,"source":{"type":"derived","expr":"(0.785398163 * {.shaft_d} * {.shaft_d} * {.shaft_length} + 0.785398163 * {.hub_d} * {.hub_d} * {.hub_t} + ({.paddle_width} * ({.lever_reach} - {.paddle_start} - {.paddle_width}) + 0.785398163 * {.paddle_width} * {.paddle_width}) * ({.paddle_base_t} - {.paddle_relief}) + (({.paddle_width} - 2 * {.step_1_inset}) * ({.lever_reach} - {.paddle_start} - {.paddle_width}) + 0.785398163 * ({.paddle_width} - 2 * {.step_1_inset}) * ({.paddle_width} - 2 * {.step_1_inset})) * ({.step_1_height} - {.paddle_base_t}) + (({.paddle_width} - 2 * {.step_2_inset}) * ({.lever_reach} - {.paddle_start} - {.paddle_width}) + 0.785398163 * ({.paddle_width} - 2 * {.step_2_inset}) * ({.paddle_width} - 2 * {.step_2_inset})) * ({.step_2_height} - {.step_1_height}) + (({.paddle_width} - 2 * {.step_3_inset}) * ({.lever_reach} - {.paddle_start} - {.paddle_width}) + 0.785398163 * ({.paddle_width} - 2 * {.step_3_inset}) * ({.paddle_width} - 2 * {.step_3_inset})) * ({.step_3_height} - {.step_2_height}) + (({.paddle_width} - 2 * {.step_4_inset}) * ({.lever_reach} - {.paddle_start} - {.paddle_width}) + 0.785398163 * ({.paddle_width} - 2 * {.step_4_inset}) * ({.paddle_width} - 2 * {.step_4_inset})) * ({.step_4_height} - {.step_3_height}) + (({.paddle_width} - 2 * {.step_5_inset}) * ({.lever_reach} - {.paddle_start} - {.paddle_width}) + 0.785398163 * ({.paddle_width} - 2 * {.step_5_inset}) * ({.paddle_width} - 2 * {.step_5_inset})) * ({.lever_standoff} - {.step_4_height})) * {std.density.steel}","via":"user"}}],"note":"WORKED OUT, not published: no page states a weight for it (CMMG, Sportsman's Warehouse, Impact Guns). Its own steel from the drawing's sizes: the shaft as a plain cylinder, the hub's disc, the thumb piece's slab less the relief under it, and the five terraces, times std.density.steel. An upper figure: the cuts inside the receiver (the flat for the trigger's tail, the detent's holes, the neck beside the lever) aren't taken off, and no source dimensions CMMG's; the reference model's own cut (a .330 neck flatted .073 from the axis over 0.33 in of the shaft) would take about 0.06 oz. The ± covers that and the density's range."},"shaft_d":{"label":"Diameter of the shaft that turns in the receiver","kind":"length","measurements":[{"id":"standard","value":0.37225,"unit":"in","pm":0.00075,"source":{"type":"derived","expr":"{std.ar15.selector_shaft_d}","via":"user"},"note":"The Army's drawing of the standard selector (9381367: .3730 DIA -.0015), which CMMG says its own meets (\"meets or exceeds mil-spec\", https://cmmg.com/safety-selector-ar15). No page of CMMG's states a diameter."}]},"shaft_length":{"label":"Length of shaft between the faces that bear on the receiver's two sides","kind":"length","measurements":[{"id":"tdp","value":0.9375,"unit":"in","pm":0.0175,"stated":".760 +.010 -.005 and .170 +.015 -.005 (1.180 REF overall, 1.010 REF)","source":{"type":"standard","doc":"US Army TDP drawing 9381367 (Selector, Fire Control), sheet 1 of 2, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p65: the view along the lever, zone D-4","via":"user"},"note":"The chain's reading: 1.180 REF is the whole part across the rifle, from the top of the serrations to the shaft's far end; .170 from the far end to the detent notches' centre line; 1.010 REF from that line to the top of the serrations; .760 from that line to the lever's inner face, the face View H measures .050 REF (the hub) and .250 (the serrations' top) from: 1.010 less .760 is that .250. So the shaft is .760 and .170, .930 at the nominals, and the middle of its tolerance (.920 to .955) is the figure here."},{"id":"model","value":0.944,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Fire_Selector.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle)","method":"the shaft's end face (y 0) to the lever's inner face (the plane at y 23.9776 mm)","via":"user"}}],"adopt":{"from":"tdp","reason":"The Army's drawing; the reference model's shaft is inside its tolerance."},"note":"A one-sided selector: from the lever's inner face, which bears on the receiver's left side, to the shaft's far end. The receiver is .88 wide (std.ar15.lower_body_width): the end stands out of its right side by the difference."},"shaft_end_chamfer":{"label":"Chamfer round the shaft's far end","kind":"length","measurements":[{"id":"tdp","value":0.024,"unit":"in","pm":0.011,"stated":".024 ±.011 X 45° ±2°","source":{"type":"standard","doc":"US Army TDP drawing 9381367 (Selector, Fire Control), sheet 1 of 2, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p65: the view along the lever, zone D-4","via":"user"},"note":"The end that stands out of the receiver's right side. The reference model has .015."}]},"hub_d":{"label":"Diameter of the lever's hub","kind":"length","measurements":[{"id":"tdp","value":0.48,"unit":"in","pm":0.01,"stated":".48 DIA","source":{"type":"standard","doc":"US Army TDP drawing 9381367 (Selector, Fire Control), sheet 1 of 2, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p65: face view, zone B-7","via":"user"}},{"id":"model","value":0.477,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Fire_Selector.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle)","method":"the hub's cylinder, r 6.0579 mm","via":"user"}},{"id":"installed","value":0.47,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/rise-lpk f008e4862517 (Aero Precision M4A1 clone complete lower, mil-spec parts kit, straight left side, 1920 px: another maker's mil-spec selector, on SAFE)","scaleRef":"that photo's pin frame (data/ledger/rise-lpk.yaml): takedown (1781.5, 356.5), pivot (121.5, 362.5), 6.375 apart: 260.4 px/in; the selector's axis lands at (1572.4, 477.8) by std.ar15.selector_x and selector_y, and the hub's middle reads (1572, 478.8)","method":"the hub's top and bottom on a 5x crop: y 417.6 and 540.0, 122.4 px","via":"harvest"},"note":"A check of the drawing's reading on a real part of another make; ± for edges two pixels soft."}],"adopt":{"from":"tdp","reason":"The Army's drawing; the reference model and a photo of a mil-spec selector installed agree with it."}},"hub_t":{"label":"Thickness of the hub's plate (its inner face on the receiver to its outer face)","kind":"length","measurements":[{"id":"tdp","value":0.05,"unit":"in","pm":0.005,"stated":".050 (the view along the lever); .050 REF (View H)","source":{"type":"standard","doc":"US Army TDP drawing 9381367 (Selector, Fire Control), sheet 1 of 2, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p65: the view along the lever, zone D-4, and View H (scale 10/1)","via":"user"},"note":"View H measures it from the same line as the serrations' heights: the lever's inner face."},{"id":"model","value":0.052,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Fire_Selector.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle)","method":"the planes at y 23.9776 and 25.2984 mm","via":"user"}}],"adopt":{"from":"tdp","reason":"The Army's drawing; the reference model has two thousandths more."}},"pointer_reach":{"label":"The pointer's tip, from the selector's axis","kind":"length","measurements":[{"id":"tdp","value":0.34,"unit":"in","pm":0.01,"stated":".34 (1.15 REF = .34 + .81)","source":{"type":"standard","doc":"US Army TDP drawing 9381367 (Selector, Fire Control), sheet 1 of 2, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p65: face view, zone B-7","via":"user"},"note":"Opposite the thumb piece. On the mil-spec selector installed in references/rise-lpk f008e4862517 the tip reads .32 from the axis at 260.4 px/in: a casting's point, a little blunt."},{"id":"model","value":0.3385,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Fire_Selector.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle)","method":"where the pointer's two flanks meet, x 8.5979 mm","via":"user"}}],"adopt":{"from":"tdp","reason":"The Army's drawing; the reference model agrees."}},"pointer_angle":{"label":"The pointer's included angle","kind":"angle","measurements":[{"id":"tdp","value":60,"unit":"deg","pm":2,"stated":"60° INCL ±2.0°","source":{"type":"standard","doc":"US Army TDP drawing 9381367 (Selector, Fire Control), sheet 1 of 2, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p65: face view, zone B-7","via":"user"},"note":"The reference model's two flanks are 60° apart too (normals 0.5, ±0.866)."}]},"pointer_fillet_r":{"label":"Radius that blends each of the pointer's flanks into the hub","kind":"length","measurements":[{"id":"tdp","value":0.09,"unit":"in","pm":0.01,"stated":".09 R","source":{"type":"standard","doc":"US Army TDP drawing 9381367 (Selector, Fire Control), sheet 1 of 2, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p65: face view, zone B-7","via":"user"},"note":"Two leaders, one to each shoulder: a hollow radius, which gives the hub the onion shape the face view draws."}]},"paddle_width":{"label":"Width of the thumb piece","kind":"length","measurements":[{"id":"tdp","value":0.25,"unit":"in","pm":0.005,"stated":".250 (.125 from its centre line)","source":{"type":"standard","doc":"US Army TDP drawing 9381367 (Selector, Fire Control), sheet 1 of 2, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p65: face view, zone B-7","via":"user"}},{"id":"model","value":0.251,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Fire_Selector.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle)","method":"its two side planes, z ±3.1877 mm","via":"user"}},{"id":"installed","value":0.258,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/rise-lpk f008e4862517 (Aero Precision M4A1 clone complete lower, mil-spec parts kit, straight left side, 1920 px: another maker's mil-spec selector, on SAFE)","scaleRef":"that photo's pin frame, 260.4 px/in (hub_d's measurement says how it is checked)","method":"the thumb piece's upper and lower edges on a 5x crop: y 444.4 and 511.6, 67.2 px","via":"harvest"},"note":"A check of the drawing's reading on a real part of another make."}],"adopt":{"from":"tdp","reason":"The Army's drawing; the reference model and a photo of a mil-spec selector installed agree with it."}},"lever_reach":{"label":"The lever's reach from the selector's axis to its tip","kind":"length","measurements":[{"id":"tdp","value":0.81,"unit":"in","pm":0.01,"stated":".81 (also .09 + .72 REF)","source":{"type":"standard","doc":"US Army TDP drawing 9381367 (Selector, Fire Control), sheet 1 of 2, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p65: face view, zone B-7","via":"user"}},{"id":"model","value":0.8045,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Fire_Selector.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle)","method":"the far end's cylinder: its axis 17.2466 mm from the selector's, r 3.1877 mm","via":"user"}},{"id":"installed","value":0.809,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/rise-lpk f008e4862517 (Aero Precision M4A1 clone complete lower, mil-spec parts kit, straight left side, 1920 px: another maker's mil-spec selector, on SAFE)","scaleRef":"that photo's pin frame, 260.4 px/in (hub_d's measurement says how it is checked)","method":"the thumb piece's rear end on a 5x crop, x 1783.0, from the axis at 1572.4","via":"harvest"},"note":"A check of the drawing's reading on a real part of another make."}],"adopt":{"from":"tdp","reason":"The Army's drawing; the reference model and a photo of a mil-spec selector installed agree with it."},"note":"The thumb piece's far end."},"paddle_start":{"label":"Where the thumb piece begins, from the selector's axis (its near end, a full round)","kind":"length","measurements":[{"id":"tdp","value":0.09,"unit":"in","pm":0.01,"stated":".09 (and .72 REF from there to the far end: .81)","source":{"type":"standard","doc":"US Army TDP drawing 9381367 (Selector, Fire Control), sheet 1 of 2, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p65: face view, zone B-7","via":"user"},"note":"Read between the axis' line and the line the .72 REF starts from; the view along the rifle has the serrations beginning the same .1 below the axis, and View H's detail of that end puts it .192 above the relief's step at .281."},{"id":"model","value":-0.1255,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Fire_Selector.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle)","method":"the near end's cylinders are about the selector's own axis (r 3.1877 mm and the terraces' radii): the slab's end is its radius on the pointer's side of the axis","via":"user"},"note":"Negative: past the axis, toward the pointer."}],"adopt":{"from":"tdp","reason":"The Army's drawing, which CMMG's photo of its own selector bears out; the reference model draws another casting, the one Aero's kit has."},"note":"The one place the drawing and the reference model part. On the drawing the thumb piece's near end is .09 from the axis on the thumb piece's side, so the hub's face is plain round the axis; the reference model centres that end's round on the axis, as Aero's kit selector does (references/rise-lpk f008e4862517: its terraces' front end is .128 ahead of the axis). CMMG's own photo (b9b588162284) has the hub's face plain round the axis and the thumb piece's slab rising from it below: the drawing's."},"paddle_base_t":{"label":"Height of the thumb piece's slab, from the lever's inner face","kind":"length","measurements":[{"id":"tdp","value":0.125,"unit":"in","pm":0.005,"stated":".125","source":{"type":"standard","doc":"US Army TDP drawing 9381367 (Selector, Fire Control), sheet 1 of 2, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p65: View H (scale 10/1)","via":"user"},"note":"View H's six figures across (.250, .240, .220, .200, .170, .125) are measured from one line, the lever's inner face (the same line as .050 REF, the hub): how far out each terrace's top stands. Its five figures down (.009 to .110) are how far each terrace's end is drawn in from the slab's. The reference model reads the view the same way (its tops .124, .172, .200, .224, .239, .253 from the inner face; drawn in .010, .025, .043, .074, .110). The kit selector's ledger (rise-lpk.selector_serration_height) took the .110 for a height."},{"id":"model","value":0.124,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Fire_Selector.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle)","method":"the slab's top plane at y 27.1272 mm, from the inner face at 23.9776","via":"user"}}],"adopt":{"from":"tdp","reason":"The Army's drawing; the reference model agrees."}},"paddle_relief":{"label":"Gap between the thumb piece's underside and the receiver's side","kind":"length","measurements":[{"id":"tdp","value":0.015,"unit":"in","pm":0.005,"stated":".015","source":{"type":"standard","doc":"US Army TDP drawing 9381367 (Selector, Fire Control), sheet 1 of 2, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p65: the view along the rifle, zone B-5","via":"user"},"note":"The thumb piece's underside steps away from the lever's inner face; View H draws the step .192 beyond the slab's near end. CMMG's photo shows the step across the underside."},{"id":"model","value":0.014,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Fire_Selector.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle)","method":"the underside's plane at y 24.3332 mm, from the inner face at 23.9776","via":"user"}}],"adopt":{"from":"tdp","reason":"The Army's drawing; the reference model agrees."}},"paddle_relief_start":{"label":"Where the relief under the thumb piece begins, from the selector's axis","kind":"length","measurements":[{"id":"tdp","value":0.281,"unit":"in","pm":0.005,"stated":".281","source":{"type":"standard","doc":"US Army TDP drawing 9381367 (Selector, Fire Control), sheet 1 of 2, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p65: the view along the rifle, zone B-5","via":"user"},"note":"From the axis' line to the line through View H's circle: taken as the relief's step, which is where the reference model has it; the hub ends at .24."},{"id":"model","value":0.2805,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Fire_Selector.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle)","method":"the step's plane at x -7.1247 mm","via":"user"}}],"adopt":{"from":"tdp","reason":"The Army's drawing; the reference model has the step there."}},"step_1_inset":{"label":"First serration (terrace): drawn in from the slab's outline","kind":"length","measurements":[{"id":"tdp","value":0.009,"unit":"in","pm":0.005,"stated":".009","source":{"type":"standard","doc":"US Army TDP drawing 9381367 (Selector, Fire Control), sheet 1 of 2, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p65: View H (scale 10/1); FULL R ON ALL STEPPED SERRATIONS (face view)","via":"user"},"note":"The reference model: .010."}]},"step_1_height":{"label":"First serration (terrace): its top, from the lever's inner face","kind":"length","measurements":[{"id":"tdp","value":0.17,"unit":"in","pm":0.005,"stated":".170","source":{"type":"standard","doc":"US Army TDP drawing 9381367 (Selector, Fire Control), sheet 1 of 2, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p65: View H (scale 10/1)","via":"user"},"note":"The reference model: .172."}]},"step_2_inset":{"label":"Second serration (terrace): drawn in from the slab's outline","kind":"length","measurements":[{"id":"tdp","value":0.025,"unit":"in","pm":0.005,"stated":".025","source":{"type":"standard","doc":"US Army TDP drawing 9381367 (Selector, Fire Control), sheet 1 of 2, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p65: View H (scale 10/1)","via":"user"},"note":"The reference model: .025."}]},"step_2_height":{"label":"Second serration (terrace): its top, from the lever's inner face","kind":"length","measurements":[{"id":"tdp","value":0.2,"unit":"in","pm":0.005,"stated":".200","source":{"type":"standard","doc":"US Army TDP drawing 9381367 (Selector, Fire Control), sheet 1 of 2, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p65: View H (scale 10/1)","via":"user"},"note":"The reference model: .200."}]},"step_3_inset":{"label":"Third serration (terrace): drawn in from the slab's outline","kind":"length","measurements":[{"id":"tdp","value":0.043,"unit":"in","pm":0.005,"stated":".043","source":{"type":"standard","doc":"US Army TDP drawing 9381367 (Selector, Fire Control), sheet 1 of 2, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p65: View H (scale 10/1)","via":"user"},"note":"The reference model: .043."}]},"step_3_height":{"label":"Third serration (terrace): its top, from the lever's inner face","kind":"length","measurements":[{"id":"tdp","value":0.22,"unit":"in","pm":0.005,"stated":".220","source":{"type":"standard","doc":"US Army TDP drawing 9381367 (Selector, Fire Control), sheet 1 of 2, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p65: View H (scale 10/1)","via":"user"},"note":"The reference model: .224."}]},"step_4_inset":{"label":"Fourth serration (terrace): drawn in from the slab's outline","kind":"length","measurements":[{"id":"tdp","value":0.075,"unit":"in","pm":0.005,"stated":".075","source":{"type":"standard","doc":"US Army TDP drawing 9381367 (Selector, Fire Control), sheet 1 of 2, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p65: View H (scale 10/1)","via":"user"},"note":"The reference model: .074."}]},"step_4_height":{"label":"Fourth serration (terrace): its top, from the lever's inner face","kind":"length","measurements":[{"id":"tdp","value":0.24,"unit":"in","pm":0.005,"stated":".240","source":{"type":"standard","doc":"US Army TDP drawing 9381367 (Selector, Fire Control), sheet 1 of 2, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p65: View H (scale 10/1)","via":"user"},"note":"The reference model: .239."}]},"step_5_inset":{"label":"Fifth serration (the ridge along the middle): drawn in from the slab's outline","kind":"length","measurements":[{"id":"tdp","value":0.11,"unit":"in","pm":0.005,"stated":".110","source":{"type":"standard","doc":"US Army TDP drawing 9381367 (Selector, Fire Control), sheet 1 of 2, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p65: View H (scale 10/1)","via":"user"},"note":"It leaves a ridge .030 wide; its top is lever_standoff. The reference model: .110."}]},"lever_standoff":{"label":"How far the lever stands out from the receiver's side","kind":"length","measurements":[{"id":"tdp","value":0.25,"unit":"in","pm":0.005,"stated":".250 (View H); 1.010 REF less .760","source":{"type":"standard","doc":"US Army TDP drawing 9381367 (Selector, Fire Control), sheet 1 of 2, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p65: View H (scale 10/1) and the view along the lever, zone D-4","via":"user"}},{"id":"model","value":0.253,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Fire_Selector.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle)","method":"the ridge's top plane at y 30.4038 mm, from the inner face at 23.9776","via":"user"}}],"adopt":{"from":"tdp","reason":"The Army's drawing, by two of its views; the reference model agrees."},"note":"The top of the last serration, from the lever's inner face."},"throw":{"label":"The arc it turns through between safe and fire","kind":"angle","measurements":[{"id":"cmmg","value":90,"unit":"deg","stated":"standard 90° throw operation","source":{"type":"spec","publisher":"manufacturer","name":"CMMG, Safety Selector, AR15 (55CA741)","url":"https://cmmg.com/safety-selector-ar15","retrieved":"2026-10-12","via":"harvest"},"note":"The drawing's section G-G has the detent's seats 90° apart. Nothing is posed by it: the selector is drawn on SAFE."}]}}},{"subject":"daniel-defense-103-barrel","title":"Daniel Defense 10.3 in 5.56 cold hammer forged barrel, government profile, carbine gas, stripped (07-077-16176-018)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"primary-arms","value":1.15,"unit":"lb","pm":0.005,"stated":"1.15 lbs weight","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Daniel Defense CHF Chrome Lined 5.56 AR-15 Barrel - Carbine - Government - 10.3\" (SKU and MPN 07-077-16176-018), Features (its Specifications say \"Weight 1.15 lbs\")","url":"https://www.primaryarms.com/daniel-defense-5-56-10-3-17-chf-barrel-carbine-length-gas-system-07-077-16176-018","retrieved":"2026-10-06","via":"harvest"}},{"id":"operationparts","value":1.15,"unit":"lb","pm":0.005,"stated":"Stripped Barrel 1.15lbs Barrel w/ LPG 1.23lbs Barrel w/ FSB 1.46lbs","source":{"type":"spec","publisher":"retailer","name":"OperationParts, Daniel Defense 10.3″ 5.56mm GOV’T Carbine CHF Barrel – Stripped (07-077-16176-018), description (its table says \"Weight 1.15 lb\")","url":"https://operationparts.com/product/daniel-defense-10-3-5-56mm-gov-t-carbine-chf-barrel-stripped/","retrieved":"2026-10-06","via":"harvest"},"note":"The maker's own words by their form (\"Our 10.3” 5.56 barrel\"): the one page that sets the bare barrel's weight beside its two siblings'."},{"id":"alexanders","value":1.15,"unit":"lb","pm":0.005,"stated":"Weight: 1.15 lbs","source":{"type":"spec","publisher":"retailer","name":"Alexander's Store, Daniel Defense 10.3\" 5.56 NATO Government Carbine Barrel, 1:7 (MPN 07-077-16176-018), Specifications","url":"https://alexandersstore.com/product/dd-bbl-556-10-3-gov-car/","retrieved":"2026-10-06","via":"harvest"}},{"id":"charlies","value":1.15,"unit":"lb","pm":0.005,"stated":"Weight 1.15 lbs.","source":{"type":"spec","publisher":"retailer","name":"Charlie's Custom Clones, Daniel Defense DD new 10.3\" Mk18 barrel virgin, .070\" gas (its own number DD061281; MPN 07-077-16176-018), its table","url":"https://charliescustomclones.com/daniel-defense-dd-new-10-3-mk18-barrel-virgin/","retrieved":"2026-10-06","via":"harvest"}},{"id":"ar15discounts","value":21.6,"unit":"oz","pm":0.05,"stated":"Weight 21.6 oz","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, Daniel Defense 10.3\" 5.56 NATO CHF Carbine Length 1:7 Government Contour AR-15 Barrel - 07-077-16176-018 (its own number 7575), Additional information","url":"https://ar15discounts.com/products/daniel-defense-10-3-5-56-nato-chf-carbine-length-17-government-contour-ar-15-barrel/","retrieved":"2026-10-06","via":"harvest"},"note":"Beside \"Dimensions 12.3 × 3 × 3 in\": a parcel's size, and with it a parcel's weight (1.35 lb)."},{"id":"dirty-bird","value":21.6,"unit":"oz","pm":0.05,"stated":"Weight 21.6 oz","source":{"type":"spec","publisher":"retailer","name":"Dirty Bird Industries, Daniel Defense 10.3\" 5.56 NATO CHF Carbine Length 1:7 Government Contour AR-15 Barrel - 07-077-16176-018 (its own number 7575), Additional information","url":"https://dirtybirdusa.com/products/daniel-defense-10-3-5-56-nato-chf-carbine-length-17-government-contour-ar-15-barrel/","retrieved":"2026-10-06","via":"harvest"},"note":"The same feed as AR15Discounts (the same number 7575, the same \"Dimensions 12.3 × 3 × 3 in\")."},{"id":"botach","value":2,"unit":"lb","pm":0.005,"stated":"Weight: 2.00 LBS","source":{"type":"spec","publisher":"retailer","name":"Botach, Daniel Defense 5.56mm NATO 10.3\" 1:7\" CMV CHF Carbine-Length Gov't Barrel Assembly 07-077-16176-018, the shop's fields under the price","url":"https://botach.com/daniel-defense-5-56mm-nato-10-3-1-7-cmv-chf-carbine-length-govt-barrel-assembly-07-077-16176-018/","retrieved":"2026-10-06","via":"harvest"},"note":"A shop's shipping weight (its platform's field), not the barrel's."}],"adopt":{"from":"primary-arms","reason":"1.15 lb on four sellers' pages, and on OperationParts' as the lightest of the three versions the maker sells (1.23 with the low-profile gas block, 1.46 with the front sight base), which a boxed weight would not be. The 21.6 oz of AR15Discounts and Dirty Bird (one feed) stands beside a parcel's 12.3 × 3 × 3 in, and Botach's 2.00 LBS is a shipping field. Held against the model: its volume as steel is 4% over 1.15 lb, as it should be with its chamber still solid, and 11% under 21.6 oz (the part's test)."},"note":"Four sellers state 1.15 lb for this number, one of them in a table of the barrel's three versions (stripped, with the low-profile gas block, with the front sight base): the bare barrel's. The 21.6 oz of two shops that share a feed stands beside a parcel's size, and Botach's 2.00 LBS is its shop's weight field. No one weighed it; the maker's own page isn't read (its site refuses the reader, PLAN D59)."},"length":{"label":"Barrel length as its maker states it","kind":"length","measurements":[{"id":"primary-arms","value":10.3,"unit":"in","pm":0.05,"stated":"10.3\" cold hammer-forged barrel","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Daniel Defense CHF Chrome Lined 5.56 AR-15 Barrel - Carbine - Government - 10.3\" (SKU and MPN 07-077-16176-018), Features (its Specifications say \"Barrel Length 10.3\")","url":"https://www.primaryarms.com/daniel-defense-5-56-10-3-17-chf-barrel-carbine-length-gas-system-07-077-16176-018","retrieved":"2026-10-06","via":"harvest"}},{"id":"operationparts","value":10.3,"unit":"in","pm":0.05,"stated":"Barrel Length 10.3″","source":{"type":"spec","publisher":"retailer","name":"OperationParts, Daniel Defense 10.3″ 5.56mm GOV’T Carbine CHF Barrel – Stripped (07-077-16176-018), Specifications","url":"https://operationparts.com/product/daniel-defense-10-3-5-56mm-gov-t-carbine-chf-barrel-stripped/","retrieved":"2026-10-06","via":"harvest"}},{"id":"right-to-bear","value":10.3,"unit":"in","pm":0.05,"stated":"Length 10.3\"","source":{"type":"spec","publisher":"retailer","name":"Right To Bear, Daniel Defense 10.3\" 5.56 NATO CHF Carbine 1:7 Government AR-15 Barrel (07-077-16176-018), Barrel Specifications","url":"https://www.righttobear.com/daniel-defense-10-3-5-56-nato-chf-carbine-1-7-government-ar-15-barrel/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"primary-arms","reason":"The seller on file whose page is the part's own; the others state the same 10.3."},"note":"The nominal length, on every seller's page; none says between which points. Taken from the barrel's breech face, as the catalog's 16 in barrels are (bca-556-16-mid-barrel.length's note). From the closed bolt's face, the Army's way, the barrel would be 0.126 shorter end to end (bca-556-16-mid-barrel.bolt_face_behind_breech): the maker's square-on picture is against that (overall_length), and what it leaves open is in the ± of every length scaled from this one."},"journal_od":{"label":"The gas block journal's diameter","kind":"length","measurements":[{"id":"primary-arms","value":0.75,"unit":"in","pm":0.0005,"stated":"Gas Seat Diameter .750","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Daniel Defense CHF Chrome Lined 5.56 AR-15 Barrel - Carbine - Government - 10.3\" (SKU and MPN 07-077-16176-018), Specifications","url":"https://www.primaryarms.com/daniel-defense-5-56-10-3-17-chf-barrel-carbine-length-gas-system-07-077-16176-018","retrieved":"2026-10-06","via":"harvest"}},{"id":"operationparts","value":0.75,"unit":"in","pm":0.0005,"stated":"Diameter At Gas Port .750″","source":{"type":"spec","publisher":"retailer","name":"OperationParts, Daniel Defense 10.3″ 5.56mm GOV’T Carbine CHF Barrel – Stripped (07-077-16176-018), Specifications","url":"https://operationparts.com/product/daniel-defense-10-3-5-56mm-gov-t-carbine-chf-barrel-stripped/","retrieved":"2026-10-06","via":"harvest"}},{"id":"ar15discounts","value":0.75,"unit":"in","pm":0.005,"stated":"Gas Block Journal 0.75","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, Daniel Defense 10.3\" 5.56 NATO CHF Carbine Length 1:7 Government Contour AR-15 Barrel - 07-077-16176-018 (its own number 7575), Additional information","url":"https://ar15discounts.com/products/daniel-defense-10-3-5-56-nato-chf-carbine-length-17-government-contour-ar-15-barrel/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"primary-arms","reason":"The seller on file whose page is the part's own, to three places; two more sellers state the same."}},"tenon_length":{"label":"The barrel's tenon: its breech face behind the shoulder the extension's front face seats on","kind":"length","measurements":[{"id":"tdp","value":0.62,"unit":"in","pm":0.001,"source":{"type":"derived","expr":"{std.ar15.barrel_tenon_length}","via":"user"},"note":"The Army's drawing 8448549, .620 ±.001, in the standard's ledger."}]},"extension_behind_breech":{"label":"The barrel extension's rear end behind the barrel's breech face","kind":"length","measurements":[{"id":"model","value":0.501,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{std.ar15.barrel_extension_behind_breech}","via":"harvest"},"note":"The readings and their sources are in the standard's ledger (std.ar15.barrel_extension_length, std.ar15.barrel_tenon_length)."}],"note":"One extension for every 5.56 barrel in the catalog (std.ar15.barrel_extension_behind_breech: the reference CAD set's 1.121 less the Army's .620 tenon). This barrel's own pictures read its extension about 0.03 longer behind the flange than that set's (extension_rear_x)."},"barrel_ahead_of_flange":{"label":"The barrel's own length ahead of the extension's front face: the flange's front face to the muzzle","kind":"length","measurements":[{"id":"published","value":9.68,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{.length} - {.tenon_length}","via":"harvest"}}],"note":"The ruler for every length read off the maker's square-on picture: both its ends show there (the flange's front face and the muzzle's), and neither the extension's own length nor where the breech lies inside it comes into it. The ± is the published length's."},"overall_length":{"label":"End to end, the extension's rear end to the muzzle's face","kind":"length","measurements":[{"id":"published","value":10.801,"unit":"in","pm":0.07,"source":{"type":"derived","expr":"{.length} + {.extension_behind_breech}","via":"harvest"}},{"id":"photo","value":10.8,"unit":"in","pm":0.1,"source":{"type":"photo","photo":"references/daniel-defense-103-barrel 50c0d40d42c5 (Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000)","scaleRef":"its barrel extension's diameter, 91.08 px between its edges at grey 200 (the mean over columns 16 to 84), as the Army's .999 (extension_od): 91.17 px/in","method":"its two ends, each a straight edge across the part: the rear end's at column 7.5 (within 0.4 px over rows 470 to 524), the muzzle's at 991.7 (rows 490 to 511: its rim is broken, and the rows outside those end 1.5 to 3 px short): 984.2 px","via":"harvest"},"note":"The ± is what the edges' grey leaves: 10.66 at 235, 10.83 at 170."},{"id":"pitches","value":10.9,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/daniel-defense-103-barrel 50c0d40d42c5 (Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000)","scaleRef":"the thread's own stripes, 3.225 px apart (the peak of the spectrum of rows 478 to 518 over columns 942 to 986, 13.6 periods; 3.219 to 3.232 on three bands of rows), as 28 to the inch (thread_pitch): 90.3 px/in","method":"the same two ends, 984.2 px apart","via":"harvest"},"note":"A ruler at the muzzle end alone, along the barrel: the ± is its three bands' spread and a pixel at each end."}],"adopt":{"from":"published","reason":"Lengths at the published length, taken from the breech face. The maker's square-on picture reads 10.80 by its extension and 10.90 by its thread's pitch: the published figure or a little more, and not the 10.675 a 10.3 from the bolt's face would make it."},"note":"The published 10.3 from the breech face, with the standard extension's 0.501 behind that. The maker's square-on picture is the check, by three rulers of its own. Its thread's stripes, 3.225 px apart, make it 10.90 end to end at 28 to the inch: 0.9% over, and 2.1% over what a 10.3 taken from the bolt's face would make it (10.675: bca-556-16-mid-barrel.bolt_face_behind_breech). Its extension's diameter as the Army's .999 makes it 10.80 with the edges read at grey 200 (10.66 at 235, 10.83 at 170, their 50% level). Its .750 journal makes it 10.95, 1.4% over: a dark tube reads thin on white (CLAUDE.md; BCM's barrel did the same by 2.5%), so the journal's scale is for diameters and the published length for lengths. The larger picture (0ec43808ddef) is no use here: taken from 16 in, its ends are their rims' arcs, and its lens draws the thread's pitch 4% short at the muzzle end."},"extension_rear_x":{"label":"The barrel extension's rear end, from the flange's rear face (negative: inside the receiver)","kind":"length","measurements":[{"id":"model","value":-0.99,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{std.ar15.barrel_extension_flange_thickness} - {std.ar15.barrel_extension_length}","via":"harvest"},"note":"The reference CAD set's extension, 1.121 from its front face to its rear end, less its 0.131 flange."},{"id":"photo","value":-1.026,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/daniel-defense-103-barrel 50c0d40d42c5 (Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000)","scaleRef":"the flange's front face to the muzzle's face, 878.2 px (columns 113.5 and 991.7, the silhouette at grey 200), as barrel_ahead_of_flange (9.680: the published 10.3 less the Army's .620 tenon): 90.72 px/in","method":"the rear end's edge (column 7.5) to the flange's rear face (column 100.6: its lower edge, where the pin doesn't stand in front of it): 93.1 px","via":"harvest"}}],"adopt":{"from":"model","reason":"The standard's extension, as the receiver and the carrier are drawn for it; this barrel's pictures read it 0.036 longer, which stays here beside it."},"note":"This barrel's own pictures read its extension 0.03 to 0.04 longer behind the flange than the reference CAD set's: 1.026 here, and 1.003 to 1.015 on the larger picture (178.2 px between its rear end's face, behind its rim's arc, and the flange's rear face, at the scales its extension's and its journal's diameters give there). The catalog's three 16 in barrels read 0.979, 0.984 and 0.996 by their photos. Drawn as the standard's: an extension is an interface part, and one barrel's two pictures 1.5 of their ± off isn't yet a different extension. Open (the part's gaps)."},"flange_front_x":{"label":"The extension flange's front face, ahead of its rear face (the flange's thickness)","kind":"length","measurements":[{"id":"model","value":0.131,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.ar15.barrel_extension_flange_thickness}","via":"harvest"},"note":"The reference CAD set's flange."},{"id":"photo","value":0.142,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/daniel-defense-103-barrel 50c0d40d42c5 (Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000)","scaleRef":"the flange's front face to the muzzle's face, 878.2 px (columns 113.5 and 991.7, the silhouette at grey 200), as barrel_ahead_of_flange (9.680: the published 10.3 less the Army's .620 tenon): 90.72 px/in","method":"the flange's rear face (column 100.6) to its front face (column 113.5: both edges of the silhouette step there within 0.05 px of each other): 12.9 px","via":"harvest"}}],"adopt":{"from":"model","reason":"The standard's flange, which a barrel nut is drawn round; the picture reads a pixel more (0.011 in), inside its ±."},"note":"Where the barrel's own length begins: every position ahead of it is read from this face on the picture and added to it."},"flange_od":{"label":"The barrel extension's flange, its diameter as the side pictures have it at the journal's scale","kind":"length","measurements":[{"id":"photo-b","value":1.187,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/daniel-defense-103-barrel 50c0d40d42c5 (Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000)","scaleRef":"its gas block journal's diameter, 67.44 px between its edges at grey 200 (the mean over columns 740 to 880), as the published .750 (journal_od): 89.91 px/in","method":"the silhouette's widest, columns 104 to 110: 106.75 px against the journal's 67.44 (ratio 1.5830)","via":"harvest"}},{"id":"photo-a","value":1.189,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/daniel-defense-103-barrel 0ec43808ddef (Dirty Bird's copy of 07-077-16176-018_01, the series Primary Arms serves: the barrel from its right side on white, the muzzle at the right, 2000 x 1333)","scaleRef":"its gas block journal's diameter, 131.70 px between its edges at grey 192, the edge's 50% level (the mean over columns 1525 to 1680), as the published .750 (journal_od): 175.60 px/in","method":"the silhouette's widest, columns 228 to 244: 208.80 px against the journal's 131.70 (ratio 1.5854)","via":"harvest"}}],"adopt":{"from":"photo-b","reason":"The traced picture's own reading, which its outline is scaled by; the larger picture reads 0.002 more."},"note":"The traced outline's scale reference (the silhouette's greatest height). The extension reads 1.4% large at the journal's scale in both pictures (extension_od_photo): the flange as drawn is flange_d."},"extension_od":{"label":"The barrel extension's body, its diameter (what goes into the receiver)","kind":"length","measurements":[{"id":"tdp","value":0.999,"unit":"in","pm":0.001,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_od}","via":"user"},"note":"The Army's limit on drawing 8448548 (\"DIAMETER NOT TO EXCEED .9990 FOR THIS LENGTH AFTER ASSEMBLY AND BEFORE FINISH\"), read for BCM's barrel and adopted there: its source is in that ledger."}]},"extension_od_photo":{"label":"The barrel extension's body as the side pictures have it at the journal's scale","kind":"length","measurements":[{"id":"photo-b","value":1.013,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/daniel-defense-103-barrel 50c0d40d42c5 (Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000)","scaleRef":"its gas block journal's diameter, 67.44 px between its edges at grey 200 (the mean over columns 740 to 880), as the published .750 (journal_od): 89.91 px/in","method":"the extension behind its flange, columns 16 to 84: 91.08 px against the journal's 67.44 (ratio 1.3506)","via":"harvest"}},{"id":"photo-a","value":1.01,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/daniel-defense-103-barrel 0ec43808ddef (Dirty Bird's copy of 07-077-16176-018_01, the series Primary Arms serves: the barrel from its right side on white, the muzzle at the right, 2000 x 1333)","scaleRef":"its gas block journal's diameter, 131.70 px between its edges at grey 192, the edge's 50% level (the mean over columns 1525 to 1680), as the published .750 (journal_od): 175.60 px/in","method":"the extension behind its flange, columns 70 to 185: 177.39 px against the journal's 131.70 (ratio 1.3469)","via":"harvest"}}],"adopt":{"from":"photo-b","reason":"The traced picture's, the same one flange_od is read on, so that the two give the flange as drawn."},"note":"Not the extension's size (extension_od: it goes into a 1.000 bore): how much the extension reads large beside the barrel in a picture. 1.1 to 1.4% in two pictures from two cameras, as BCM's barrel read 1.2% in Primary Arms' photo: the phosphated barrel reads thin on white and the extension, another piece with another finish, less so. The flange as drawn takes this ratio out (flange_d)."},"flange_d":{"label":"The barrel extension's flange, its diameter as drawn","kind":"length","measurements":[{"id":"photo","value":1.171,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{.flange_od} * {.extension_od} / {.extension_od_photo}","via":"harvest"}}],"note":"The flange at the scale its own extension gives: the picture's flange against the picture's extension, times the Army's .999. The reference CAD set's flange is 1.170 across."},"chamber_od":{"label":"The chamber section, between the flange and its taper: its diameter","kind":"length","measurements":[{"id":"photo-a","value":0.993,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/daniel-defense-103-barrel 0ec43808ddef (Dirty Bird's copy of 07-077-16176-018_01, the series Primary Arms serves: the barrel from its right side on white, the muzzle at the right, 2000 x 1333)","scaleRef":"its gas block journal's diameter, 131.70 px between its edges at grey 192, the edge's 50% level (the mean over columns 1525 to 1680), as the published .750 (journal_od): 175.60 px/in","method":"columns 265 to 355: 174.34 px against the journal's 131.70 (ratio 1.3238)","via":"harvest"}},{"id":"photo-b","value":0.992,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/daniel-defense-103-barrel 50c0d40d42c5 (Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000)","scaleRef":"its gas block journal's diameter, 67.44 px between its edges at grey 200 (the mean over columns 740 to 880), as the published .750 (journal_od): 89.91 px/in","method":"columns 122 to 166: 89.16 px against the journal's 67.44 (ratio 1.3221)","via":"harvest"}}],"adopt":{"from":"photo-a","reason":"The finer picture (176 px/in against 90); the square-on one reads 0.001 less."}},"chamber_front_x":{"label":"Where the chamber section ends and its taper begins, ahead of the flange's rear face","kind":"length","measurements":[{"id":"photo","value":0.781,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/daniel-defense-103-barrel 50c0d40d42c5 (Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000)","scaleRef":"the flange's front face to the muzzle's face, 878.2 px (columns 113.5 and 991.7, the silhouette at grey 200), as barrel_ahead_of_flange (9.680: the published 10.3 less the Army's .620 tenon): 90.72 px/in","method":"the flange's front face (column 113.5) to where two lines through the silhouette's width meet, one over the chamber section (columns 124 to 166) and one over the taper (182 to 246): column 172.5, 0.650 in; ahead of the flange's front face as drawn (flange_front_x)","via":"harvest"}}]},"taper_front_x":{"label":"Where the taper ends and the section under the hand guard begins, ahead of the flange's rear face","kind":"length","measurements":[{"id":"photo","value":1.641,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/daniel-defense-103-barrel 50c0d40d42c5 (Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000)","scaleRef":"the flange's front face to the muzzle's face, 878.2 px (columns 113.5 and 991.7, the silhouette at grey 200), as barrel_ahead_of_flange (9.680: the published 10.3 less the Army's .620 tenon): 90.72 px/in","method":"the flange's front face (column 113.5) to where the line through the taper's width (columns 182 to 246) meets the one through the section ahead of it (262 to 400): column 250.5, 1.510 in; ahead of the flange's front face as drawn (flange_front_x)","via":"harvest"}}]},"handguard_section_rear_od":{"label":"The section under the hand guard, its diameter at its rear end (the taper's front end)","kind":"length","measurements":[{"id":"photo-a","value":0.688,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/daniel-defense-103-barrel 0ec43808ddef (Dirty Bird's copy of 07-077-16176-018_01, the series Primary Arms serves: the barrel from its right side on white, the muzzle at the right, 2000 x 1333)","scaleRef":"its gas block journal's diameter, 131.70 px between its edges at grey 192, the edge's 50% level (the mean over columns 1525 to 1680), as the published .750 (journal_od): 175.60 px/in","method":"the line through the section's width over columns 530 to 1240 (129.82 px less 0.01751 a column, rms 0.13 px), at the taper's front end (column 511.5): 120.86 px against the journal's 131.70","via":"harvest"}},{"id":"photo-b","value":0.687,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/daniel-defense-103-barrel 50c0d40d42c5 (Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000)","scaleRef":"its gas block journal's diameter, 67.44 px between its edges at grey 200 (the mean over columns 740 to 880), as the published .750 (journal_od): 89.91 px/in","method":"the line through the section's width over columns 262 to 626 (66.41 px less 0.0185 a column, rms 0.13 px), at the taper's front end (column 250.5): 61.78 px against the journal's 67.44","via":"harvest"}}],"adopt":{"from":"photo-a","reason":"The finer picture; the square-on one reads 0.001 less."},"note":"This section is not a cylinder: it narrows toward the muzzle by 0.076 in over 4.3 in, in both pictures (a line through its width fits each to 0.15 px), from two cameras, one of them square on. A hammer-forged barrel's own taper, not the lens."},"handguard_section_front_od":{"label":"The section under the hand guard, its diameter at its front end (where the flare to the collar begins)","kind":"length","measurements":[{"id":"photo-a","value":0.612,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/daniel-defense-103-barrel 0ec43808ddef (Dirty Bird's copy of 07-077-16176-018_01, the series Primary Arms serves: the barrel from its right side on white, the muzzle at the right, 2000 x 1333)","scaleRef":"its gas block journal's diameter, 131.70 px between its edges at grey 192, the edge's 50% level (the mean over columns 1525 to 1680), as the published .750 (journal_od): 175.60 px/in","method":"the same line at the flare's rear end (column 1277.5): 107.45 px against the journal's 131.70","via":"harvest"}},{"id":"photo-b","value":0.607,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/daniel-defense-103-barrel 50c0d40d42c5 (Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000)","scaleRef":"its gas block journal's diameter, 67.44 px between its edges at grey 200 (the mean over columns 740 to 880), as the published .750 (journal_od): 89.91 px/in","method":"the same line at the flare's rear end (column 639.6): 54.58 px against the journal's 67.44","via":"harvest"}}],"adopt":{"from":"photo-a","reason":"The finer picture; the square-on one reads 0.005 less, inside its ± of half a pixel."}},"flare_length":{"label":"The flare up to the collar: its knee behind the collar's rear corner","kind":"length","measurements":[{"id":"photo","value":0.34,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/daniel-defense-103-barrel 0ec43808ddef (Dirty Bird's copy of 07-077-16176-018_01, the series Primary Arms serves: the barrel from its right side on white, the muzzle at the right, 2000 x 1333)","scaleRef":"its gas block journal's diameter, 131.70 px between its edges at grey 192, the edge's 50% level (the mean over columns 1525 to 1680), as the published .750 (journal_od): 175.60 px/in","method":"the silhouette's width over columns 1150 to 1345 at grey 192: a line through the flare's straight end (columns 1306 to 1337: 0.725 px a column, 19.9° a side) meets the line through the section behind it (columns 1150 to 1234) at column 1282.4; the collar's full width begins at 1342.05 (collar_rear_x on the square-on picture): 59.65 px","via":"harvest"}}],"note":"The flare is a curve that straightens into a cone of 20° a side just behind the collar. Its knee is where the line through that straight end meets the line through the section under the hand guard; the curve runs flare_fillet either side of it."},"flare_fillet":{"label":"The flare's curve: how far it runs either side of its knee","kind":"length","measurements":[{"id":"photo","value":0.219,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/daniel-defense-103-barrel 0ec43808ddef (Dirty Bird's copy of 07-077-16176-018_01, the series Primary Arms serves: the barrel from its right side on white, the muzzle at the right, 2000 x 1333)","scaleRef":"its gas block journal's diameter, 131.70 px between its edges at grey 192, the edge's 50% level (the mean over columns 1525 to 1680), as the published .750 (journal_od): 175.60 px/in","method":"a curve tangent to both lines (a parabola through their meeting point) fitted to the silhouette's width over columns 1150 to 1345: it leaves each line 38.5 px from the knee (rms 0.38 px over the 196 columns, against 2.07 with a sharp knee)","via":"harvest"}}]},"flare_rear_x":{"label":"The flare's knee ahead of the flange's rear face","kind":"length","measurements":[{"id":"photo","value":5.984,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.collar_rear_x} - {.flare_length}","via":"harvest"}}],"note":"Read on the square-on picture alone, where a pixel is 0.011 in and the curve is three dozen pixels long, a line through the whole flare (columns 646 to 668) meets the section behind it at 5.931: a shallower line through the curve, not this knee."},"collar_rear_x":{"label":"Where the flare ends at the collar's full diameter, ahead of the flange's rear face","kind":"length","measurements":[{"id":"photo","value":6.324,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/daniel-defense-103-barrel 50c0d40d42c5 (Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000)","scaleRef":"the flange's front face to the muzzle's face, 878.2 px (columns 113.5 and 991.7, the silhouette at grey 200), as barrel_ahead_of_flange (9.680: the published 10.3 less the Army's .620 tenon): 90.72 px/in","method":"the flange's front face (column 113.5) to where the line through the flare (columns 646 to 668) meets the collar's level (678 to 724): column 675.4, 6.193 in; ahead of the flange's front face as drawn (flange_front_x)","via":"harvest"}}]},"collar_od":{"label":"The collar behind the gas block journal, its diameter","kind":"length","measurements":[{"id":"photo-a","value":0.85,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/daniel-defense-103-barrel 0ec43808ddef (Dirty Bird's copy of 07-077-16176-018_01, the series Primary Arms serves: the barrel from its right side on white, the muzzle at the right, 2000 x 1333)","scaleRef":"its gas block journal's diameter, 131.70 px between its edges at grey 192, the edge's 50% level (the mean over columns 1525 to 1680), as the published .750 (journal_od): 175.60 px/in","method":"columns 1350 to 1450: 149.23 px against the journal's 131.70 (ratio 1.1331)","via":"harvest"}},{"id":"photo-b","value":0.848,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/daniel-defense-103-barrel 50c0d40d42c5 (Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000)","scaleRef":"its gas block journal's diameter, 67.44 px between its edges at grey 200 (the mean over columns 740 to 880), as the published .750 (journal_od): 89.91 px/in","method":"columns 678 to 724: 76.23 px against the journal's 67.44 (ratio 1.1304)","via":"harvest"}}],"adopt":{"from":"photo-a","reason":"The finer picture; the square-on one reads 0.002 less."}},"journal_rear_x":{"label":"The gas block journal's rear shoulder (the collar's front face) ahead of the flange's rear face","kind":"length","measurements":[{"id":"photo","value":6.943,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/daniel-defense-103-barrel 50c0d40d42c5 (Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000)","scaleRef":"the flange's front face to the muzzle's face, 878.2 px (columns 113.5 and 991.7, the silhouette at grey 200), as barrel_ahead_of_flange (9.680: the published 10.3 less the Army's .620 tenon): 90.72 px/in","method":"the flange's front face (column 113.5) to the collar's front face (column 731.45: both edges of the silhouette step there, 731.49 and 731.40): 6.812 in; ahead of the flange's front face as drawn (flange_front_x)","via":"harvest"}}],"note":"A gas block's rear face comes back to this shoulder (Murf's picture of the sibling sold with a block, 7a92aa7b5869, has it there). The catalog's mid-length barrels have theirs at 8.85 to 8.87: this one is 1.91 to 1.93 behind them."},"journal_front_x":{"label":"The gas block journal's front end (where the barrel steps down) ahead of the flange's rear face","kind":"length","measurements":[{"id":"photo","value":8.802,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/daniel-defense-103-barrel 50c0d40d42c5 (Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000)","scaleRef":"the flange's front face to the muzzle's face, 878.2 px (columns 113.5 and 991.7, the silhouette at grey 200), as barrel_ahead_of_flange (9.680: the published 10.3 less the Army's .620 tenon): 90.72 px/in","method":"the flange's front face (column 113.5) to the step ahead of the journal (column 900.1: the upper edge at 900.35, the lower at 899.84): 8.671 in; ahead of the flange's front face as drawn (flange_front_x)","via":"harvest"}}],"note":"The journal is 1.86 long, as the catalog's mid-length barrels' are (1.87 on BCM's): long enough for a front sight base's two bands, which the maker fits to this barrel's sibling."},"gas_port_x":{"label":"The gas port ahead of the flange's rear face","kind":"length","measurements":[{"id":"photo","value":7.226,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/daniel-defense-103-barrel 0ec43808ddef (Dirty Bird's copy of 07-077-16176-018_01, the series Primary Arms serves: the barrel from its right side on white, the muzzle at the right, 2000 x 1333)","scaleRef":"its gas block journal's diameter as the published .750 (131.70 px at grey 192: 175.60 px/in), for the port's distance from the collar's front face; that face is journal_rear_x, from the square-on picture","method":"the port's dark spot (centre column 1505.5, row 607: 63.5 px above the axis on a radius of 67, so 21 px nearer the lens than the axis, which from 16 in and 670 px off the lens's foot shows it 5.1 px further out than it is: column 1500.4) from the collar's front face (column 1449.8: its rim's arc fitted on the silhouette's upper and lower edges, 1449.2 and 1450.4): 50.6 px, 0.288 in; read without the two corrections, 0.277; taken as 0.283 and added to journal_rear_x","via":"harvest"}}],"note":"No page gives a distance (Primary Arms: \"Carbine gas system\"). The port is on top; only the larger picture, turned about 19° toward the lens, shows it: 0.283 ahead of the collar's front face (the Army's rifle barrel has .295 on 8448548, a mid-length chart .300, BCM's barrel 0.28). Checks: the catalog's three mid-length barrels have their ports at 9.13 to 9.17, 1.90 to 1.94 ahead of this one, where Aero's carbine-length gas tube is 2 in shorter than its mid-length one (9.75 and 11.75; its other page's \"9.8\" would make it 1.95). With that tube in BCM's gas block on this port, its rear end stands in the carrier key's socket, short of its bottom (the part's test). Right To Bear says \"Dimpled? No\", and the pictures show no dimple or flat under the journal."},"gas_port_d":{"label":"The gas port's diameter","kind":"length","measurements":[{"id":"charlies","value":0.07,"unit":"in","pm":0.0005,"stated":"Daniel Defense DD new 10.3\" Mk18 barrel virgin, .070\" gas","source":{"type":"spec","publisher":"retailer","name":"Charlie's Custom Clones, Daniel Defense DD new 10.3\" Mk18 barrel virgin, .070\" gas (its own number DD061281; MPN 07-077-16176-018), the page's title","url":"https://charliescustomclones.com/daniel-defense-dd-new-10-3-mk18-barrel-virgin/","retrieved":"2026-10-06","via":"harvest"},"note":"A seller's title, for the hole the model cuts."},{"id":"photo","value":0.064,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/daniel-defense-103-barrel 0ec43808ddef (Dirty Bird's copy of 07-077-16176-018_01, the series Primary Arms serves: the barrel from its right side on white, the muzzle at the right, 2000 x 1333)","scaleRef":"its gas block journal's diameter, 131.70 px between its edges at grey 192, the edge's 50% level (the mean over columns 1525 to 1680), as the published .750 (journal_od): 175.60 px/in","method":"the port's dark spot along the barrel at half its depth of grey (columns 1500.2 to 1511.4 on row 606): 11.2 px; along the barrel it is not foreshortened","via":"harvest"}}],"adopt":{"from":"charlies","reason":"The one stated figure for this number, a seller's; the picture's spot agrees with it within its ± and not with .082."},"note":"No seller's table states one. Charlie's Custom Clones' title for this number says .070; a customer's review on Primary Arms' page says \"Daniel Defense released two different types, one with a 0.070\\\" gas port and the other is 0.082\\\" gas port\". The picture's spot is the smaller."},"muzzle_od":{"label":"The diameter behind the muzzle thread","kind":"length","measurements":[{"id":"photo-a","value":0.74,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/daniel-defense-103-barrel 0ec43808ddef (Dirty Bird's copy of 07-077-16176-018_01, the series Primary Arms serves: the barrel from its right side on white, the muzzle at the right, 2000 x 1333)","scaleRef":"its gas block journal's diameter beside this section, 131.07 px at grey 192 over columns 1700 to 1775 (the journal reads 0.9% narrower there than at its rear end in this picture: its lower edge), as the published .750 (journal_od)","method":"columns 1795 to 1835: 129.33 px (ratio 0.9867)","via":"harvest"}},{"id":"photo-b","value":0.742,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/daniel-defense-103-barrel 50c0d40d42c5 (Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000)","scaleRef":"its gas block journal's diameter, 67.44 px between its edges at grey 200 (the mean over columns 740 to 880), as the published .750 (journal_od): 89.91 px/in","method":"columns 908 to 928: 66.69 px against the journal's 67.44 (ratio 0.9890)","via":"harvest"}}],"adopt":{"from":"photo-a","reason":"The finer picture; the square-on one reads 0.002 more."},"note":"The last section before the shoulder, 0.38 long: 0.005 under the journal on the radius."},"shoulder_x":{"label":"The muzzle shoulder ahead of the flange's rear face","kind":"length","measurements":[{"id":"photo","value":9.178,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/daniel-defense-103-barrel 50c0d40d42c5 (Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000)","scaleRef":"the flange's front face to the muzzle's face, 878.2 px (columns 113.5 and 991.7, the silhouette at grey 200), as barrel_ahead_of_flange (9.680: the published 10.3 less the Army's .620 tenon): 90.72 px/in","method":"the flange's front face (column 113.5) to the shoulder's face (column 934.25: both edges of the silhouette step there, 934.24 and 934.27): 9.047 in; ahead of the flange's front face as drawn (flange_front_x)","via":"harvest"}}],"note":"Where the thread begins: a muzzle device or its washer seats here. With the thread's length it adds up to the barrel's own length ahead of the flange (0.131 + 9.680 = 9.811). A relief groove a pitch wide shows between the shoulder and the first thread in both pictures; it isn't drawn."},"thread_length":{"label":"The muzzle thread's length","kind":"length","measurements":[{"id":"photo","value":0.633,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/daniel-defense-103-barrel 50c0d40d42c5 (Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000)","scaleRef":"the flange's front face to the muzzle's face, 878.2 px (columns 113.5 and 991.7, the silhouette at grey 200), as barrel_ahead_of_flange (9.680: the published 10.3 less the Army's .620 tenon): 90.72 px/in","method":"the shoulder's face (column 934.25) to the muzzle's face (column 991.7): 57.45 px","via":"harvest"}},{"id":"pitches","value":0.636,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/daniel-defense-103-barrel 50c0d40d42c5 (Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000)","scaleRef":"the thread's own stripes, 3.225 px apart (the peak of the spectrum of rows 478 to 518 over columns 942 to 986, 13.6 periods), as 28 to the inch (thread_pitch)","method":"the same 57.45 px: 17.8 pitches","via":"harvest"}}],"adopt":{"from":"photo","reason":"At the scale every other length is read at; counted in its own pitches it is 0.003 more."},"note":"The Army's barrel has .63 from its shoulder to its muzzle (8448549 sheet 1)."},"thread_major_d":{"label":"The muzzle thread's major diameter (its crests)","kind":"length","measurements":[{"id":"tdp","value":0.4957,"unit":"in","pm":0.0033,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.thread_major_d}","via":"user"},"note":"\"1/2-28 UNEF-2A MAJOR DIA .4989/.4924\" on the Army's drawing 8448549, read for BCM's barrel: its source is in that ledger."}],"note":"The Army barrel's 1/2-28 thread, for the 1/2 X 28 the sellers state: what the model's thread is drawn at, not a measurement of this barrel. The pictures' silhouette of the thread is 0.484 (the larger) and 0.473 (the square-on one) at the journal's scale, between its crests and its roots."},"thread_minor_d":{"label":"The muzzle thread's minor diameter (its roots)","kind":"length","measurements":[{"id":"tdp","value":0.4551,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.thread_minor_d}","via":"user"},"note":"\"MINOR DIA .4551 MAX\" on the same drawing, read for BCM's barrel."}]},"thread_pitch":{"label":"The muzzle thread's pitch","kind":"length","measurements":[{"id":"primary-arms","value":0.03571,"unit":"in","pm":0.00005,"stated":"Thread Pattern 1/2 X 28","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Daniel Defense CHF Chrome Lined 5.56 AR-15 Barrel - Carbine - Government - 10.3\" (SKU and MPN 07-077-16176-018), Specifications (its Features say \"Threaded 1/2x28\")","url":"https://www.primaryarms.com/daniel-defense-5-56-10-3-17-chf-barrel-carbine-length-gas-system-07-077-16176-018","retrieved":"2026-10-06","via":"harvest"}},{"id":"photo","value":0.03555,"unit":"in","pm":0.0003,"source":{"type":"photo","photo":"references/daniel-defense-103-barrel 50c0d40d42c5 (Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000)","scaleRef":"the flange's front face to the muzzle's face, 878.2 px (columns 113.5 and 991.7, the silhouette at grey 200), as barrel_ahead_of_flange (9.680: the published 10.3 less the Army's .620 tenon): 90.72 px/in","method":"the thread's stripes along rows 478 to 518 over columns 942 to 986: the spectrum's peak at a period of 3.225 px (3.219 to 3.232 on three bands of rows; 13.6 periods)","via":"harvest"}}],"adopt":{"from":"primary-arms","reason":"The seller's statement for this barrel; its own picture reads the same pitch within half a percent."},"note":"28 threads to the inch by four sellers' statements (Primary Arms, OperationParts \"1 ⁄ 2 × 28 TPI\", Alexander's and AR15Discounts \"1/2×28\", Botach \"1/2x28\"). The maker's square-on picture resolves it: its stripes are 28.1 to the inch at the published length's scale."},"bore_d":{"label":"The bore's diameter (across the lands)","kind":"length","measurements":[{"id":"tdp","value":0.219,"unit":"in","pm":0.001,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.bore_d}","via":"user"},"note":"\".219 DIA+.001\" on the Army's drawing 8448549, read for BCM's barrel: its source is in that ledger."}],"note":"The cartridge's, for the hole the barrel is drawn with: the sellers state \"5.56 NATO\" and no bore, so this is the Army barrel's for that cartridge and not a measurement of this one."},"index_pin_d":{"label":"The barrel indexing pin's diameter","kind":"length","measurements":[{"id":"model","value":0.125,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.index_pin_d}","via":"user"},"note":"The reference CAD set's pin, read for BCM's barrel: its source is in that ledger."},{"id":"photo","value":0.123,"unit":"in","pm":0.011,"source":{"type":"photo","photo":"references/daniel-defense-103-barrel 50c0d40d42c5 (Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000)","scaleRef":"the flange's front face to the muzzle's face, 878.2 px (columns 113.5 and 991.7, the silhouette at grey 200), as barrel_ahead_of_flange (9.680: the published 10.3 less the Army's .620 tenon): 90.72 px/in","method":"the pin on the upper edge behind the flange: its rear edge at column 88.3, its front edge at 99.4: 11.1 px","via":"harvest"}}],"adopt":{"from":"model","reason":"The standard part's size; this barrel's picture reads it within a pixel."}},"index_pin_x":{"label":"The barrel indexing pin's axis behind the flange's rear face","kind":"length","measurements":[{"id":"photo","value":0.074,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/daniel-defense-103-barrel 50c0d40d42c5 (Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000)","scaleRef":"the flange's front face to the muzzle's face, 878.2 px (columns 113.5 and 991.7, the silhouette at grey 200), as barrel_ahead_of_flange (9.680: the published 10.3 less the Army's .620 tenon): 90.72 px/in","method":"the middle of the pin's two edges on the upper silhouette (columns 88.3 and 99.4: 93.85) to the flange's rear face (column 100.6): 6.75 px","via":"harvest"}}],"note":"The reference CAD set has 0.0765 (0.2075 behind the flange's front face). In the breech view (3e288080affe) the pin stands against the flange's rear face."},"index_pin_top":{"label":"The barrel indexing pin's top above the bore's axis","kind":"length","measurements":[{"id":"photo","value":0.581,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/daniel-defense-103-barrel 50c0d40d42c5 (Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000)","scaleRef":"the flange's own radius in the same picture, 53.38 px at grey 200, as half of flange_d (0.5855)","method":"the pin's top on the upper silhouette (rows 443.4 to 443.7 over columns 90 to 96) above the axis (row 496.5 there): 53.0 px, 0.993 of the flange's radius","via":"harvest"}}],"note":"A hair under the flange's rim: in the square-on picture the pin's top is 0.4 px lower than the flange's."},"extension_mouth_d":{"label":"The barrel extension's rear opening, its diameter at the rear face","kind":"length","measurements":[{"id":"model","value":0.77,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_mouth_d}","via":"user"},"note":"The inside of a mil-spec extension as the reference CAD set has it, read for BCM's barrel (its source is in that ledger), for how the rear end looks: the breech view (3e288080affe) shows this barrel's lugs and its two M4 feed ramps. Appearance only."}]},"extension_lug_bore_d":{"label":"The circle the extension's locking lugs leave between their tips","kind":"length","measurements":[{"id":"model","value":0.572,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_lug_bore_d}","via":"user"}}]},"extension_lug_depth":{"label":"The locking lugs' front faces, ahead of the extension's rear end","kind":"length","measurements":[{"id":"model","value":0.214,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_lug_depth}","via":"user"}}]},"extension_recess_d":{"label":"The recess ahead of the lugs, which the bolt's lugs turn in: its diameter","kind":"length","measurements":[{"id":"model","value":0.83,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_recess_d}","via":"user"}}]},"extension_recess_depth":{"label":"The recess's front end, ahead of the extension's rear end","kind":"length","measurements":[{"id":"model","value":0.595,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_recess_depth}","via":"user"}}]},"extension_lug_count":{"label":"The barrel extension's locking lugs: how many","kind":"count","measurements":[{"id":"model","value":8,"unit":"count","pm":0,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Extension.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"eight cylinder faces of radius .2860 about the bore, each 20° of the turn, at every 45° from the indexing pin's side: a lug under the pin, a slot half way to the next (.cache/batch46/daniel-defense-103-barrel/lugs.py: the faces of it that aren't surfaces of revolution about the bore, by where they lie along its axis, from its front face at 0 to its rear end at 1.121, and round it, from the indexing pin's side)","via":"user"}}],"note":"The standard extension's, for how this barrel's rear end looks (the sellers: \"A4 barrel extension\", \"Feed Ramps M4\"); its own breech view (3e288080affe) shows five of them on the far side of the opening, the near ones behind the wall, and can't count the turn. The reference CAD set (D49): a model source, never authoritative."},"extension_lug_rear_cone":{"label":"The lugs' rear faces: how far ahead of the extension's rear end the cone from the opening's radius comes down to the lugs' tips","kind":"length","measurements":[{"id":"model","value":0.099,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Extension.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"the cone (45°) from radius .3850 at the rear end, 1.121, to the lug tips' cylinder of radius .2860, which begins at 1.022 (.cache/batch46/daniel-defense-103-barrel/lugs.py: the faces of it that aren't surfaces of revolution about the bore, by where they lie along its axis, from its front face at 0 to its rear end at 1.121, and round it, from the indexing pin's side)","via":"user"}}]},"extension_slot_width":{"label":"The slots between the extension's locking lugs: their width","kind":"length","measurements":[{"id":"model","value":0.124,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Extension.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"each slot's two flanks are planes along the axis, parallel to the slot's own radius and 0.0620 from the bore's axis either side of it (sixteen planes, their normals at 22.5° and every 45° on); they run from the lugs' front faces, 0.907, to the rear end (.cache/batch46/daniel-defense-103-barrel/lugs.py: the faces of it that aren't surfaces of revolution about the bore, by where they lie along its axis, from its front face at 0 to its rear end at 1.121, and round it, from the indexing pin's side)","via":"user"}}]},"extension_slot_floor":{"label":"The slots between the lugs: their floor, from the bore's axis","kind":"length","measurements":[{"id":"model","value":0.38,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Extension.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"each slot's floor is a plane 0.3800 from the bore's axis, square to the slot's radius (eight planes); its corners are at radius .3850, the rear opening's (.cache/batch46/daniel-defense-103-barrel/lugs.py: the faces of it that aren't surfaces of revolution about the bore, by where they lie along its axis, from its front face at 0 to its rear end at 1.121, and round it, from the indexing pin's side)","via":"user"}}]},"feed_ramp_d":{"label":"The M4 feed ramps: the diameter of the cylinder each is cut as","kind":"length","measurements":[{"id":"model","value":0.28,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Extension.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"two cylinders of radius 0.1400, between 0.937 and the rear end (.cache/batch46/daniel-defense-103-barrel/lugs.py: the faces of it that aren't surfaces of revolution about the bore, by where they lie along its axis, from its front face at 0 to its rear end at 1.121, and round it, from the indexing pin's side)","via":"user"}}],"note":"The sellers: \"Feed Ramps M4\" (Primary Arms), \"A4 with extended M4 feed ramps\" (Alexander's). Two bright cuts through the rear end's lower rim in the breech view (3e288080affe), as the reference set has them."},"feed_ramp_angle":{"label":"The feed ramps: how far each cylinder's axis leans from the bore's","kind":"angle","measurements":[{"id":"model","value":45,"unit":"deg","pm":0.1,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Extension.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"each axis lies in the plane of the bore's axis and one of the two slots either side of the bottom (opposite the pin), direction (±0.2706, -0.6533, 0.7071): 45° to the bore, coming toward it going forward (.cache/batch46/daniel-defense-103-barrel/lugs.py: the faces of it that aren't surfaces of revolution about the bore, by where they lie along its axis, from its front face at 0 to its rear end at 1.121, and round it, from the indexing pin's side)","via":"user"}}]},"feed_ramp_axis_r":{"label":"The feed ramps: each cylinder's axis from the bore's axis at the extension's rear end","kind":"length","measurements":[{"id":"model","value":0.286,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Extension.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"each axis is 0.2860 from the bore's at the rear end (1.121), 0.1870 at 1.022 and 0.0720 at the lugs' front faces (0.907) (.cache/batch46/daniel-defense-103-barrel/lugs.py: the faces of it that aren't surfaces of revolution about the bore, by where they lie along its axis, from its front face at 0 to its rear end at 1.121, and round it, from the indexing pin's side)","via":"user"}}]},"outline_flange_front":{"label":"The flange's front face in the traced outline's own frame (from the extension's rear end, at the journal's scale)","kind":"length","measurements":[{"id":"photo","value":1.189,"unit":"in","pm":0.019,"source":{"type":"photo","photo":"references/daniel-defense-103-barrel 50c0d40d42c5 (Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, on white, 1000 x 1000)","scaleRef":"scale from daniel-defense-103-barrel.flange_od = 1.187 in (y-extent 106 px → 89.3 px/in)","method":"x_max in y [-0.58, -0.53] of the traced outline (tools/trace.py); the flange's front face in the outline's own frame (from the extension's rear face, at the journal's scale): where the barrel's own length begins","via":"harvest"}}]},"outline_muzzle":{"label":"The muzzle's face in the traced outline's own frame (from the extension's rear end, at the journal's scale)","kind":"length","measurements":[{"id":"photo","value":11.006,"unit":"in","pm":0.076,"source":{"type":"photo","photo":"references/daniel-defense-103-barrel 50c0d40d42c5 (Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, on white, 1000 x 1000)","scaleRef":"scale from daniel-defense-103-barrel.flange_od = 1.187 in (y-extent 106 px → 89.3 px/in)","method":"x_max of the traced outline (tools/trace.py); the muzzle's face in the outline's own frame (from the extension's rear face, at the journal's scale)","via":"harvest"}}]}}},{"subject":"daniel-defense-bcg","title":"Daniel Defense Complete Bolt Carrier Group, 5.56, phosphate (04-013-19032)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"wing","value":11.5,"unit":"oz","pm":0.05,"stated":"Weight: 11.5 oz.","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Daniel Defense 5.56 Bolt Carrier Group (MPN 04-013-19032), Specifications","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/ar-15-upper-receiver-parts/bolts-carriers/daniel-defense-5-56-bolt-carrier-group/","retrieved":"2026-10-19","via":"harvest"}},{"id":"primary-arms","value":11,"unit":"oz","pm":0.5,"stated":"Weight 11 Oz","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Daniel Defense 5.56 AR-15 Bolt Carrier Group - Phosphate (SKU and MPN 04-013-19032), Specifications; a feature bullet above has \"11 oz weight\"","url":"https://www.primaryarms.com/daniel-defense-m16-cut-complete-bolt-carrier-group-04-013-19032","retrieved":"2026-10-19","via":"harvest"},"note":"Whole ounces: ± half its last digit."},{"id":"progunfighter","value":11,"unit":"oz","pm":0.5,"stated":"The complete assembly weighs approximately 11 ounces","source":{"type":"spec","publisher":"review","name":"The Professional Gunfighter, Daniel Defense Bolt Carrier Group (BCG) Complete 5.56mm NATO Review","url":"https://progunfighter.com/daniel-defense-bolt-carrier-group-bcg-complete-5-56mm-nato-review/","retrieved":"2026-10-19","via":"harvest"},"note":"\"Approximately\", in a review written in general terms: the sellers' round figure, not a scale reading. Not an independent source."}],"adopt":{"from":"wing","reason":"The finer of the two sellers' figures, and inside the other's last digit (Primary Arms' 11 is whole ounces, 10.5 to 11.5). Neither names a scale; the half ounce between them stays visible."},"note":"The complete group (Wing: \"1x Bolt Assembly 1x Extractor 1x Cam Pin 1x Bolt Carrier 1x Carrier Gas Key 1x Firing Pin 1x Firing Pin Retaining Pin\"). Two sellers, half an ounce apart, and a review that repeats the round figure. No page says the group was put on a scale, and none weighs the carrier without its bolt."},"length":{"label":"The carrier's length","kind":"length","measurements":[{"id":"std","value":6.672,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.ar15.carrier_length}","via":"harvest"},"note":"US Army TDP drawing 8448507 (Carrier, Bolt): the tail's rear face to the front (bolt) face."}],"note":"The carrier is the standard's: Wing lists \"Mil-Spec dimensions\" and \"Profile: Full-Auto (M16)\", Primary Arms \"a mil-spec, full-auto compatible, M16 profile bolt carrier group assembly\"; no page states its size."},"od":{"label":"The carrier's diameter","kind":"length","measurements":[{"id":"std","value":0.994,"unit":"in","pm":0.0005,"source":{"type":"derived","expr":"{std.ar15.carrier_rail_od}","via":"harvest"},"note":"The diameter its rails are ground to (8448507); the body and the tail are .930 (std.ar15.carrier_body_od)."}],"note":"The carrier is the standard's (as its length): no page states it."},"serration_count":{"label":"The forward assist's serrations on the right side","kind":"count","measurements":[{"id":"std","value":28,"unit":"count","pm":0,"source":{"type":"derived","expr":"{std.ar15.carrier_serration_count}","via":"harvest"},"note":"US Army TDP drawing 8448507: \"(28) SERRATIONS\"."},{"id":"midway","value":28,"unit":"count","pm":0,"source":{"type":"photo","photo":"references/daniel-defense-bcg 471e7ee54656 (MidwayUSA's 305968.jpg: the group straight from the right, bolt to the right, 2200 x 1650)","scaleRef":"none needed: a count","method":"a luminance profile along rows 870 to 900 from x 400 to 1520, dips below the 31-pixel running mean by more than 6 levels: 28 steep faces from x 469 to 1464, 36.85 px apart (36 to 38 each), the run's pointed rear tip at 427 and the leaning flat's edge after the last","via":"harvest"}},{"id":"primary-arms","value":28,"unit":"count","pm":0,"source":{"type":"photo","photo":"references/daniel-defense-bcg 255576c2e711 (Primary Arms' 04-013-19032_01: the group straight from the right, bolt to the right, 2200 x 1467)","scaleRef":"none needed: a count","method":"the same profile along rows 725 to 740 from x 540 to 1440: 28 steep faces from x 594 to 1406, 30.07 px apart (25 to 38 each: a noisier photo, the two vents' holes beside the last two); rows 735 to 760 find the run's rear tip at 559 to 565 as a 29th dip","via":"harvest"}}],"adopt":{"from":"std","reason":"The drawing's count, which the part's two photos agree with face for face."},"note":"Counted on the part's own photos, as the check that it is the drawing's carrier: the steep face of each is a narrow dark line across the side, and a profile along the row finds every one (.cache/batch14/daniel-defense-bcg/profile.py). Both photos show the bolt to the right: the right side."},"tail_od":{"label":"The tail's diameter","kind":"length","measurements":[{"id":"std","value":0.93,"unit":"in","pm":0.0005,"source":{"type":"derived","expr":"{std.ar15.carrier_body_od}","via":"harvest"},"note":"8448507: the body and the tail."},{"id":"midway","value":0.916,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/daniel-defense-bcg 471e7ee54656 (MidwayUSA's 305968.jpg, 2200 x 1650)","scaleRef":"the serrations' pitch, .125 (std.ar15.carrier_serration_pitch): 27 pitches over 995 px = 294.8 px/in, along the same side","method":"the tail's silhouette top to bottom in columns 200 to 400 at the 235 level of 255: 269.6 to 271.1 px (268 at the 128 level). The ± is the thin reading of a dark tube's edges on white and the tail standing nearer the lens than the serrations' row by a third of an inch","via":"harvest"}},{"id":"primary-arms","value":0.906,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/daniel-defense-bcg 255576c2e711 (Primary Arms' 04-013-19032_01, 2200 x 1467)","scaleRef":"the serrations' pitch, .125: 27 pitches over 812 px = 240.6 px/in","method":"columns 300 to 450 at the 235 level: 217.7 to 218.3 px (205 to 212 at the 128 level: this photo's edges are lit, as a maker's render's are)","via":"harvest"}}],"adopt":{"from":"std","reason":"The drawing's figure. The two photos, scaled by the serrations' own pitch, read the tail 1.5% and 2.6% under it, as a dark tube on white reads: the photos' carrier is the drawing's size."},"note":"The drawing's .930, and the part's two side photos read through the serrations' pitch (.125, std.ar15.carrier_serration_pitch) as their scale: the check that the photos' carrier is the drawing's size, not a figure drawn from them. A dark tube on white reads thin at its edges (CLAUDE.md: about 3%), and both read under it by that much."},"stake_width":{"label":"The key's staking: each notch's width along the carrier, at the key's side","kind":"length","measurements":[{"id":"side","value":0.076,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/daniel-defense-bcg 255576c2e711 (Primary Arms' 04-013-19032_01: the group from the right, 2200 x 1467; a crop of x 1170 to 1420, y 555 to 640 at six times)","scaleRef":"the serrations' pitch, .125 (std.ar15.carrier_serration_pitch): 240.6 px/in along the same side (daniel-defense-bcg.serration_count)","method":"each notch's two sides where they meet the key's top edge, by eye on the crop: 18 px (x 1233 to 1251 and 1352 to 1370); the ± is three pixels, the notch's edges being a pixel or two of grey","via":"harvest"}},{"id":"top","value":0.09,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/daniel-defense-bcg ff833cef1e53 (Primary Arms' 04-013-19032_03: the group from above, 2200 x 1467; a crop of x 1030 to 1160, y 870 to 980 at eight times)","scaleRef":"the forward counterbore's rim, .273 across (std.ar15.carrier_key_cbore_d): 83 px, 304 px/in","method":"the stretch of the counterbore's rim pushed in toward the head, each side: 27.5 px along the carrier","via":"harvest"},"note":"The rim's bulge, where the metal the notch displaced went: a little longer than the notch it came from."}],"adopt":{"from":"side","reason":"The notch's own width where it is cut; the view from above reads the bulge of the rim beside it, which the displaced metal makes longer. The two agree within their ±."},"note":"\"Properly staked gas key\" (Primary Arms; Wing Tactical: \"Properly staked gas keys\"). The photos show it as a notch down the key's upper side wall at each screw, both sides: from above (ff833cef1e53) the counterbore's rim bulges into the head over a stretch centred on each screw, and from the right (255576c2e711) two notches stand in the key's side between its top and the step, 0.49 in apart at the scale below (the screws are .500 apart: std.ar15.carrier_key_screw_spacing), each centred on a screw. Drawn as a straight-sided notch cut through the wall above the step, as the side view shows its sides."},"stake_depth":{"label":"The key's staking: each notch's depth below the key's top","kind":"length","measurements":[{"id":"side","value":0.048,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/daniel-defense-bcg 255576c2e711 (Primary Arms' 04-013-19032_01, 2200 x 1467; the same crop)","scaleRef":"the serrations' pitch: 240.6 px/in (as stake_width); the key's top to its step, .059, reads 14 px","method":"from the key's top edge to the notch's bright floor, by eye on the crop: 11.5 to 12 px; the ± is the floor's two pixels and the photo standing a little above the key (its top face shows as a sliver)","via":"harvest"}}],"note":"Read on the side view, where the notch runs down the key's side from its top nearly to the step (.059 below the top: std.ar15.carrier_key_base_height less carrier_key_step_height, 14 px at this scale, which the step's line in the crop agrees with)."}}},{"subject":"daniel-defense-fixed-front-sight","title":"Daniel Defense Rail Mounted Fixed Front Sight (19-017-04013)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"primary-arms","value":1.1,"unit":"oz","stated":"1.1 oz weight","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Daniel Defense Rail-Mount Fixed AR-15 Iron Sight - Front (19-017-04013), features and table (\"Weight 1.1 Oz\")","url":"https://www.primaryarms.com/daniel-defense-rail-mount-fixed-front-sight-19-017-04013","retrieved":"2026-10-19","via":"harvest"}},{"id":"right-to-bear","value":1.1,"unit":"oz","stated":"our Rail-Mount Fixed Front Sight is both lightweight (at 1.1 oz.) and durable","source":{"type":"spec","publisher":"retailer","name":"Right to Bear, Daniel Defense Rail Mounted Fixed Sight - Front: Daniel Defense's own description, in the first person","url":"https://www.righttobear.com/daniel-defense-rail-mounted-fixed-sight-front-19-017-04013/","retrieved":"2026-10-19","via":"harvest"}},{"id":"sportsmans","value":1.1,"unit":"oz","stated":"Product Weight: 1.1oz","source":{"type":"spec","publisher":"retailer","name":"Sportsman's Warehouse, Daniel Defense Rail Mounted Fixed Front Sight (model 19-017-04013): Daniel Defense's description","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/gun-parts-accessories/gun-parts-magazines/gun-sights-lasers/daniel-defense-rail-mounted-fixed-front-sight/p/1865505","retrieved":"2026-10-19","via":"harvest"}},{"id":"wing","value":1.09,"unit":"oz","pm":0.005,"stated":"Weight: Front: 1.09 oz. Rear: 1.80 oz.","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Daniel Defense AR-15 Fixed Iron Sights (the set 19-088-09116; its spec list gives each sight)","url":"https://www.wingtactical.com/accessories/optics-sights/sights/daniel-defense-ar-15-fixed-iron-sights/","retrieved":"2026-10-19","via":"harvest"}}],"adopt":{"from":"right-to-bear","reason":"Daniel Defense's own text (Right to Bear prints it in the maker's first person); four sellers agree, Wing's 1.09 within its last digit."}},"length":{"label":"Length along the rail","kind":"length","measurements":[{"id":"wing","value":1,"unit":"in","pm":0.03,"stated":"Length: Front: 1\" Rear: 1.38\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Daniel Defense AR-15 Fixed Iron Sights (the set 19-088-09116; its spec list gives each sight)","url":"https://www.wingtactical.com/accessories/optics-sights/sights/daniel-defense-ar-15-fixed-iron-sights/","retrieved":"2026-10-19","via":"harvest"},"note":"A whole inch beside the rear's 1.38: the ± is the rounding a two-place row implies elsewhere (its rear is 1.38), not a stated one."}],"note":"Wing gives a whole inch. Modern Warriors' \"1\" (2.5cm) long\" (the discovery's reading) is no source here: its page answered the harvester 202 with an empty body. The drawing bears the inch out: at this scale the patent's rear view (scaled through the overall height) has the post's blade 0.070 in across, the Army drawing's .072 -.004."},"width":{"label":"Width","kind":"length","measurements":[{"id":"patent","value":1.245,"unit":"in","pm":0.037,"source":{"type":"photo","photo":"references/daniel-defense-fixed-front-sight 52bf49514708 (US D631,934 S, FIG. 8, the bottom view (the muzzle to the viewer's right, the screw head at the sheet's top: +z up); page 9, 300 dpi)","scaleRef":"scale from daniel-defense-fixed-front-sight.length = 1 in (x-extent 1387 px → 1387.0 px/in)","method":"height of the traced outline (tools/trace.py); the bottom view's extent across, the feet's outer edges (the screw's head left out), at the length's scale","via":"harvest"}}],"note":"No page on file states it (Modern Warriors' \"1-1⁄8\" (2.8cm) wide\", the discovery's reading, wasn't served to the harvester). Read on the patent: the bottom view at the length's scale, and the rear view through the overall height (the feet, u 551 to 1903: 1.232)."},"height":{"label":"Height above the rail's top (a fixed sight: to the ears' top)","kind":"length","measurements":[{"id":"patent","value":1.425,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/daniel-defense-fixed-front-sight 16d7ad5940f5 (US D631,934 S, FIG. 4, the rear view; the patent office's copy, page 5, 300 dpi)","scaleRef":"the overall height, the ears' top (row 666) to the feet (row 2487): 1821 px for daniel-defense-fixed-front-sight.height_drawn (1097 px/in at its 1.660)","method":"the ears' top (row 666) over the channel's ceiling (row 2229): 1563 px. ± the length's rounding and the drawing's fidelity","via":"harvest"}}],"note":"No page on file states it (Modern Warriors' \"1¾\" (4.5cm) high from top of receiver rail to top of sight housing\" wasn't served to the harvester, and the patent at the length's scale has the ears 1.425 over the rail: whatever that page measured, it isn't this). Read on the patent's rear view."},"height_drawn":{"label":"Height as the patent draws it (the feet to the crown's top), at the length's scale","kind":"length","measurements":[{"id":"patent","value":1.66,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/daniel-defense-fixed-front-sight c59fd8c41e1d (US D631,934 S (Daniel Defense, 'Front firearm sight'), FIG. 5, the screw side, the muzzle to the viewer's right (the sight's right); the patent office's copy, page 6, 300 dpi)","scaleRef":"scale from daniel-defense-fixed-front-sight.length = 1 in (x-extent 1300 px → 1300.0 px/in)","method":"height of the traced outline (tools/trace.py); the jaws' feet to the crown's top in the screw-side elevation, at the length's scale. ± covers the length's rounding (a whole inch) and a design patent's fidelity","via":"harvest"}}],"note":"What the rear elevation and the model are scaled by, so that the side and the end views of the model are one drawing."},"post_blade":{"label":"A2 front sight post: the blade's width (square)","kind":"length","measurements":[{"id":"tdp","value":0.07,"unit":"in","pm":0.002,"source":{"type":"standard","doc":"US Army drawing 9349056 (Post, Front Sight), sheet 1 of 1, rev G: the user-supplied TDP scan, PDF page 178 (references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/.../M16_Technical_Data_Package.pdf)","via":"user"},"note":".072 -.004, 2 places: the middle of its tolerance"}]},"post_blade_height":{"label":"A2 front sight post: the blade's height over its flange","kind":"length","measurements":[{"id":"tdp","value":0.268,"unit":"in","pm":0.005,"source":{"type":"standard","doc":"US Army drawing 9349056 (Post, Front Sight), sheet 1 of 1, rev G: the user-supplied TDP scan, PDF page 178 (references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/.../M16_Technical_Data_Package.pdf)","via":"user"},"note":".273 -.010: the middle of its tolerance"}]},"post_flange_d":{"label":"A2 front sight post: the flange (detent disc) across","kind":"length","measurements":[{"id":"tdp","value":0.3645,"unit":"in","pm":0.0015,"source":{"type":"standard","doc":"US Army drawing 9349056 (Post, Front Sight), sheet 1 of 1, rev G: the user-supplied TDP scan, PDF page 178 (references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/.../M16_Technical_Data_Package.pdf)","via":"user"},"note":".366 -.003 diameter, with four notches of .0455 R on a .400 diameter"}]},"post_flange_thick":{"label":"A2 front sight post: the flange's thickness","kind":"length","measurements":[{"id":"tdp","value":0.06,"unit":"in","pm":0.005,"source":{"type":"standard","doc":"US Army drawing 9349056 (Post, Front Sight), sheet 1 of 1, rev G: the user-supplied TDP scan, PDF page 178 (references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/.../M16_Technical_Data_Package.pdf)","via":"user"},"note":".065 -.010"}]},"post_root_d":{"label":"A2 front sight post: the blade's round root over the flange","kind":"length","measurements":[{"id":"tdp","value":0.165,"unit":"in","pm":0.005,"source":{"type":"standard","doc":"US Army drawing 9349056 (Post, Front Sight), sheet 1 of 1, rev G: the user-supplied TDP scan, PDF page 178 (references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/.../M16_Technical_Data_Package.pdf)","via":"user"},"note":".170 -.010 diameter, the 4 fillets of .13 R from the square blade down to it, .082 -.010 tall over the flange"}]},"post_root_height":{"label":"A2 front sight post: the fillets' height over the flange","kind":"length","measurements":[{"id":"tdp","value":0.077,"unit":"in","pm":0.005,"source":{"type":"standard","doc":"US Army drawing 9349056 (Post, Front Sight), sheet 1 of 1, rev G: the user-supplied TDP scan, PDF page 178 (references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/.../M16_Technical_Data_Package.pdf)","via":"user"},"note":".082 -.010"}]},"sight_line_above_rail":{"label":"Sight line above the rail's top (the post's tip)","kind":"length","measurements":[{"id":"wing","value":1.36,"unit":"in","pm":0.005,"stated":"Center Height Over Rail: Front: 1.36\" Rear: 1.54\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Daniel Defense AR-15 Fixed Iron Sights (the set 19-088-09116; its spec list gives each sight)","url":"https://www.wingtactical.com/accessories/optics-sights/sights/daniel-defense-ar-15-fixed-iron-sights/","retrieved":"2026-10-19","via":"harvest"}},{"id":"patent","value":1.33,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/daniel-defense-fixed-front-sight 16d7ad5940f5 (US D631,934 S, FIG. 4, the rear view; the patent office's copy, page 5, 300 dpi)","scaleRef":"the overall height, the ears' top (row 666) to the feet (row 2487): 1821 px for daniel-defense-fixed-front-sight.height_drawn (1097 px/in at its 1.660)","method":"the post's flat tip (row 769.5, column 1222) over the channel's ceiling (row 2229): 1459.5 px. ± the length's rounding, the drawing's fidelity and the post's setting","via":"harvest"}}],"adopt":{"from":"wing","reason":"A published figure for the post's tip, as the patents' heights read it; the drawing's 1.330 is the post at one setting and inside its ±. The rear's aperture is at 1.363: the pair co-witness."},"note":"The A2 post screws up and down in the sight (\"Uses standard AR-15 front sight posts\", Primary Arms): its tip's height is a setting. Wing's \"Center Height Over Rail: Front: 1.36\"\" is read as the tip: the patent, scaled by the length alone, draws it at 1.330 and the rear sight's aperture centre at 1.363, and the rear's \"1.54\" in the same row is that aperture's top."},"clamp_length":{"label":"Clamp's length along the rail","kind":"length","measurements":[{"id":"derived","value":1,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.length}","via":"harvest"},"note":"The base sits on the rail its whole length."}]},"clamp_below_rail":{"label":"Clamp's reach below the rail's top (the jaws' feet)","kind":"length","measurements":[{"id":"patent","value":0.235,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/daniel-defense-fixed-front-sight 16d7ad5940f5 (US D631,934 S, FIG. 4, the rear view; the patent office's copy, page 5, 300 dpi)","scaleRef":"the overall height, the ears' top (row 666) to the feet (row 2487): 1821 px for daniel-defense-fixed-front-sight.height_drawn (1097 px/in at its 1.660)","method":"the channel's ceiling (row 2229) to the feet (row 2487): 258 px","via":"harvest"}}]},"front_x":{"label":"Base's front face ahead of the clamp's middle (x)","kind":"length","measurements":[{"id":"derived","value":0.5,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{.length} / 2","via":"harvest"}}]},"clamp_bottom_y":{"label":"Clamp's bottom in the sight's frame (y, the rail's top is 0)","kind":"length","measurements":[{"id":"derived","value":-0.235,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"-{.clamp_below_rail}","via":"harvest"}}]},"screw_behind_front":{"label":"Clamp screw's axis behind the front face","kind":"length","measurements":[{"id":"patent","value":0.499,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/daniel-defense-fixed-front-sight c59fd8c41e1d (US D631,934 S, FIG. 5, the screw side, the muzzle to the viewer's right; page 6, 300 dpi)","scaleRef":"daniel-defense-fixed-front-sight.length = 1 in: the front face (u 1929.5) to the base's rear end (u 637.5), 1292 px (1292 px/in)","method":"the screw head's centre (u 1283.5: columns 1038 and 1529 along row 2485) behind the front face: 646 px. The insert's in the other side's elevation (FIG. 6) is 0.49 behind its front face","via":"harvest"}}],"note":"Daniel Defense (Sportsman's): \"it secures with a slotted fastener threaded into a self-locking stainless steel thread insert\": one screw across the channel, in a rail slot."},"screw_below_rail":{"label":"Clamp screw's axis below the rail's top","kind":"length","measurements":[{"id":"patent","value":0.025,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/daniel-defense-fixed-front-sight c59fd8c41e1d (US D631,934 S, FIG. 5, the screw side, the muzzle to the viewer's right; page 6, 300 dpi)","scaleRef":"daniel-defense-fixed-front-sight.length = 1 in: the front face (u 1929.5) to the base's rear end (u 637.5), 1292 px (1292 px/in)","method":"the head's centre (v 2486: rows 2241.5 and 2730 down column 1300) over the feet (v 2759), 0.211 in, less clamp_below_rail","via":"harvest"}}]},"screw_head_d":{"label":"Clamp screw's head","kind":"length","measurements":[{"id":"patent","value":0.38,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/daniel-defense-fixed-front-sight c59fd8c41e1d (US D631,934 S, FIG. 5, the screw side, the muzzle to the viewer's right; page 6, 300 dpi)","scaleRef":"daniel-defense-fixed-front-sight.length = 1 in: the front face (u 1929.5) to the base's rear end (u 637.5), 1292 px (1292 px/in)","method":"the head's outer circle, 491 px across and 488.5 down","via":"harvest"}}]},"screw_head_proud":{"label":"Clamp screw's head beyond the right foot","kind":"length","measurements":[{"id":"patent","value":0.032,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/daniel-defense-fixed-front-sight 16d7ad5940f5 (US D631,934 S, FIG. 4, the rear view; the patent office's copy, page 5, 300 dpi)","scaleRef":"the overall height, the ears' top (row 666) to the feet (row 2487): 1821 px for daniel-defense-fixed-front-sight.height_drawn (1097 px/in at its 1.660)","method":"the head's outer face (u 1938) beyond the foot's (u 1903): 35 px","via":"harvest"}}]},"screw_d":{"label":"Clamp screw's shank","kind":"length","measurements":[{"id":"assumed","value":0.19,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no page names the screw; the rear view shows its thread across the channel under the ceiling and the side view its axis 0.025 under the rail's top, a shank that lies in a rail slot (0.206 in wide).","via":"harvest"}}]},"insert_d":{"label":"Thread insert's rim across","kind":"length","measurements":[{"id":"patent","value":0.205,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/daniel-defense-fixed-front-sight 2718d851fcbd (US D631,934 S, FIG. 6, the insert side; page 7, 300 dpi)","scaleRef":"its length taken as FIG. 5's (1292 px/in): the two elevations are drawn alike","method":"the insert's outer ring along row 2380 (u 1235.5 and 1500.5): 265 px; its centre 0.49 in behind the front face (u 731.5)","via":"harvest"}}]},"feet_inner_half":{"label":"The feet's inner faces from the middle (under the rail's head)","kind":"length","measurements":[{"id":"patent","value":0.447,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/daniel-defense-fixed-front-sight 16d7ad5940f5 (US D631,934 S, FIG. 4, the rear view; the patent office's copy, page 5, 300 dpi)","scaleRef":"the overall height, the ears' top (row 666) to the feet (row 2487): 1821 px for daniel-defense-fixed-front-sight.height_drawn (1097 px/in at its 1.660)","method":"the feet's inner faces (u 735 and 1716.5): 981.5 px apart","via":"harvest"}}]},"tower_width":{"label":"The tower's width under the ears","kind":"length","measurements":[{"id":"patent","value":0.548,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/daniel-defense-fixed-front-sight 16d7ad5940f5 (US D631,934 S, FIG. 4, the rear view; the patent office's copy, page 5, 300 dpi)","scaleRef":"the overall height, the ears' top (row 666) to the feet (row 2487): 1821 px for daniel-defense-fixed-front-sight.height_drawn (1097 px/in at its 1.660)","method":"its faces (u 925 and 1526): 601 px","via":"harvest"}}]},"slit_width":{"label":"The base's two slits, each across","kind":"length","measurements":[{"id":"patent","value":0.061,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/daniel-defense-fixed-front-sight 16d7ad5940f5 (US D631,934 S, FIG. 4, the rear view; the patent office's copy, page 5, 300 dpi)","scaleRef":"the overall height, the ears' top (row 666) to the feet (row 2487): 1821 px for daniel-defense-fixed-front-sight.height_drawn (1097 px/in at its 1.660)","method":"the walls of each (u 994 to 1060, 1391 to 1459): 66 and 68 px","via":"harvest"}}],"note":"Two vertical slits in the base either side of the middle, from the channel's ceiling up (the patent's front and rear views; Primary Arms' end-on photos): the screw draws the base onto the rail."},"slit_offset":{"label":"The slits' middles from the sight's middle","kind":"length","measurements":[{"id":"patent","value":0.181,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/daniel-defense-fixed-front-sight 16d7ad5940f5 (US D631,934 S, FIG. 4, the rear view; the patent office's copy, page 5, 300 dpi)","scaleRef":"the overall height, the ears' top (row 666) to the feet (row 2487): 1821 px for daniel-defense-fixed-front-sight.height_drawn (1097 px/in at its 1.660)","method":"the slits' middles (u 1027, 1425) from the middle between the feet (u 1226.5): 199.5 and 198.5 px","via":"harvest"}}]},"slit_top_above_rail":{"label":"The slits' round tops above the rail","kind":"length","measurements":[{"id":"patent","value":0.5,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/daniel-defense-fixed-front-sight 16d7ad5940f5 (US D631,934 S, FIG. 4, the rear view; the patent office's copy, page 5, 300 dpi)","scaleRef":"the overall height, the ears' top (row 666) to the feet (row 2487): 1821 px for daniel-defense-fixed-front-sight.height_drawn (1097 px/in at its 1.660)","method":"the slits' tops (row 1680) over the ceiling (row 2229): 549 px","via":"harvest"}}]},"post_floor_above_rail":{"label":"The floor between the ears the post stands up from, above the rail","kind":"length","measurements":[{"id":"patent","value":1.073,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/daniel-defense-fixed-front-sight 16d7ad5940f5 (US D631,934 S, FIG. 4, the rear view; the patent office's copy, page 5, 300 dpi)","scaleRef":"the overall height, the ears' top (row 666) to the feet (row 2487): 1821 px for daniel-defense-fixed-front-sight.height_drawn (1097 px/in at its 1.660)","method":"the U's bottom between the ears (row 1052, column 1222) over the ceiling (row 2229): 1177 px. The post stands 0.258 above it as drawn (its blade and fillets .268 over its flange: the flange just under the floor)","via":"harvest"}}]},"post_behind_front":{"label":"The post's axis behind the front face","kind":"length","measurements":[{"id":"patent","value":0.325,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/daniel-defense-fixed-front-sight 764f426d653d (US D631,934 S, FIG. 7, the top view; page 8, 300 dpi)","scaleRef":"its own length, the rear end (u 619) to the front face (u 1975.5), 1356.5 px for daniel-defense-fixed-front-sight.length (1 in); the post's square blade in it is 95.5 px (u 1487 to 1582.5): 0.070 in, the Army drawing's .072 -.004","method":"the blade's middle (u 1535) behind the front face: 440.5 px","via":"harvest"}}]},"post_notch_r":{"label":"A2 front sight post: the flange's four notches, their radius","kind":"length","measurements":[{"id":"tdp","value":0.0455,"unit":"in","pm":0.0025,"source":{"type":"standard","doc":"US Army drawing 9349056 (Post, Front Sight), sheet 1 of 1, rev G: the user-supplied TDP scan, PDF page 178 (references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/.../M16_Technical_Data_Package.pdf)","via":"user"},"note":".0455 +.0025 R, 4 radii equally spaced"}]},"post_notch_circle_d":{"label":"A2 front sight post: the circle the notches' centres lie on","kind":"length","measurements":[{"id":"tdp","value":0.4,"unit":"in","pm":0.0005,"source":{"type":"standard","doc":"US Army drawing 9349056 (Post, Front Sight), sheet 1 of 1, rev G: the user-supplied TDP scan, PDF page 178 (references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/.../M16_Technical_Data_Package.pdf)","via":"user"},"note":"the boxed (basic) .400 diameter"}]}}},{"subject":"daniel-defense-fixed-rear-sight","title":"Daniel Defense A1.5 Fixed Rear Sight (19-064-11002)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"primary-arms","value":1.7,"unit":"oz","stated":"1.7 oz weight","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Daniel Defense A1.5 Fixed AR-15 Iron Sight - Rear (19-064-11002), features and table (\"Weight 1.7 Oz\")","url":"https://www.primaryarms.com/daniel-defense-a1-5-fixed-rear-sight-19-064-11002","retrieved":"2026-10-19","via":"harvest"}},{"id":"right-to-bear","value":1.7,"unit":"oz","stated":"our Rail-Mount Fixed rear sight is both lightweight (at 1.7 oz.) and durable.","source":{"type":"spec","publisher":"retailer","name":"Right to Bear, Daniel Defense Rail Mounted Fixed Sight - Rear: Daniel Defense's own description, in the first person","url":"https://www.righttobear.com/daniel-defense-rail-mounted-fixed-sight-rear-19-064-11002/","retrieved":"2026-10-19","via":"harvest"}},{"id":"tlo","value":1.7,"unit":"oz","pm":0.005,"stated":"Weight: 1.70 oz","source":{"type":"spec","publisher":"retailer","name":"TLO Outdoors, Daniel Defense A1.5 Fixed Rear Sight, Rock & Lock (specifications list; not a seller on file)","url":"https://tlooutdoors.com/products/dd-a1-5-fixed-rear-sight","retrieved":"2026-10-19","via":"harvest"}},{"id":"alexanders","value":1.7,"unit":"oz","stated":"Weight: 1.7 oz","source":{"type":"spec","publisher":"retailer","name":"Alexander's, Daniel Defense A1.5 Fixed Rear Sight, Key Specifications","url":"https://alexandersstore.com/product/dd-a1-5-fixed-rear-sight/","retrieved":"2026-10-19","via":"harvest"}},{"id":"wing","value":1.8,"unit":"oz","pm":0.005,"stated":"Weight: Front: 1.09 oz. Rear: 1.80 oz.","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Daniel Defense AR-15 Fixed Iron Sights (the set 19-088-09116; its spec list gives each sight)","url":"https://www.wingtactical.com/accessories/optics-sights/sights/daniel-defense-ar-15-fixed-iron-sights/","retrieved":"2026-10-19","via":"harvest"}}],"adopt":{"from":"right-to-bear","reason":"Daniel Defense's own text (Right to Bear prints it in the maker's first person), and the figure four sellers give; Wing's 1.80 oz, its own row, is 0.1 oz more and stays beside it."},"note":"Midway's \"Shipping Weight 0.138 Pounds\" is the parcel's and isn't recorded."},"length":{"label":"Length along the rail","kind":"length","measurements":[{"id":"wing","value":1.38,"unit":"in","stated":"Length: Front: 1\" Rear: 1.38\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Daniel Defense AR-15 Fixed Iron Sights (the set 19-088-09116; its spec list gives each sight)","url":"https://www.wingtactical.com/accessories/optics-sights/sights/daniel-defense-ar-15-fixed-iron-sights/","retrieved":"2026-10-19","via":"harvest"}},{"id":"tlo","value":1.38,"unit":"in","stated":"Length: 1.38\"","source":{"type":"spec","publisher":"retailer","name":"TLO Outdoors, Daniel Defense A1.5 Fixed Rear Sight, Rock & Lock (specifications list; not a seller on file)","url":"https://tlooutdoors.com/products/dd-a1-5-fixed-rear-sight","retrieved":"2026-10-19","via":"harvest"}}],"adopt":{"from":"wing","reason":"Two sellers' rows agree; Wing, a seller on file, first."},"note":"The base's two ends: the front face to the rear end over the relief. It sets the scale of the patent's side elevation and its bottom view."},"width":{"label":"Width","kind":"length","measurements":[{"id":"tlo","value":1.24,"unit":"in","stated":"Width: 1.24\"","source":{"type":"spec","publisher":"retailer","name":"TLO Outdoors, Daniel Defense A1.5 Fixed Rear Sight, Rock & Lock (specifications list; not a seller on file)","url":"https://tlooutdoors.com/products/dd-a1-5-fixed-rear-sight","retrieved":"2026-10-19","via":"harvest"}},{"id":"patent","value":1.256,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight 19d661203cc6 (US D631,935 S, FIG. 4, the rear view from the breech; the patent office's copy, page 5, 300 dpi)","scaleRef":"the overall height, wall tops (row 609) to the feet (row 2608): 1999 px for daniel-defense-fixed-rear-sight.height_drawn (1105.5 px/in)","method":"the base's feet, outer strokes' centres (u 588 and 1977): 1389 px. The ± covers the scale's (the length's last digit) and a design patent's fidelity","via":"harvest"}}],"adopt":{"from":"tlo","reason":"The published figure; the patent's base agrees within 1.3%."},"note":"TLO doesn't say what its width spans. The patent's rear elevation, at the scale its overall height gives, has the base's flared feet 1.256 in across, the clamp screw's head 0.039 in further out on the right (1.295 overall) and the drum's hub 1.247 from the left foot: TLO's 1.24 is the base's (or the hub's) width, not the screw head's."},"height":{"label":"Height, the clamp's lowest edge to the tower's top (a fixed sight: its height)","kind":"length","measurements":[{"id":"tlo","value":1.78,"unit":"in","stated":"Height: 1.78\"","source":{"type":"spec","publisher":"retailer","name":"TLO Outdoors, Daniel Defense A1.5 Fixed Rear Sight, Rock & Lock (specifications list; not a seller on file)","url":"https://tlooutdoors.com/products/dd-a1-5-fixed-rear-sight","retrieved":"2026-10-19","via":"harvest"}}],"note":"TLO's figure, read as the sight's whole height (from the jaws' feet, which stand below the rail's top, to the tower walls' top): above the rail the walls stand 1.58 in by the patent, and with the clamp below the rail 1.81. The patent at the length's scale gives 1.808, 1.6% more (height_drawn): TLO's three figures agree with the patent at 1.38 and 1.24 and not quite here."},"height_drawn":{"label":"Height as the patent draws it (the feet to the tower's top), at the length's scale","kind":"length","measurements":[{"id":"patent","value":1.806,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight 2b28fd900eb7 (US D631,935 S (Daniel Defense, 'Rear firearm sight'), FIG. 5, the drum side, the muzzle to the viewer's right (the sight's right); the patent office's copy, page 6, 300 dpi)","scaleRef":"scale from daniel-defense-fixed-rear-sight.length = 1.38 in (x-extent 1453 px → 1052.9 px/in)","method":"height of the traced outline (tools/trace.py); the jaws' feet to the tower's top in the drum-side elevation, at the length's scale. ± covers the length's last digit and a design patent's fidelity","via":"harvest"}}],"note":"What the rear elevation (FIG. 4) and the model are scaled by, so that the side and the end views of the model are one drawing. 0.028 in over TLO's 1.78 (height)."},"sight_line_above_rail":{"label":"Sight line above the rail's top (the aperture's centre)","kind":"length","measurements":[{"id":"photo","value":1.41,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight f974783e231b (Wing Tactical's photo 55197: the sight end-on from both ends, 1280 px; the right one from behind, the large aperture standing, as in the patent's FIG. 4)","scaleRef":"the sight's own overall height in the same view, the walls' top (row 337) to the feet (row 942), 605 px, for height_drawn (1.808 in); with TLO's 1.78 it reads 1.39","method":"the hole's centre (row 400: its edges at rows 368 and 432 down column 905, columns 860 and 928 along row 391) over the channel's ceiling, where the body's grey ends on the clamp screw's black (row 873, columns 790 to 1000): 473 px, 0.782 of the height. The ± takes in the scale's choice and the far end's parallax in a lens of unknown distance","via":"harvest"}},{"id":"patent","value":1.363,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight 19d661203cc6 (US D631,935 S, FIG. 4, the rear view from the breech; the patent office's copy, page 5, 300 dpi)","scaleRef":"the overall height, wall tops (row 609) to the feet (row 2608): 1999 px for daniel-defense-fixed-rear-sight.height_drawn (1105.5 px/in)","method":"the aperture hole's centre (rows 741 and 957 down column 1300, columns 1179 and 1395.5 along row 855: centre u 1287, v 849) over the channel's ceiling (row 2356, columns 1000 and 1500): 1507 px. The front view (FIG. 3) has it at 1.351 the same way","via":"harvest"}}],"adopt":{"from":"patent","reason":"The maker's drawing, and it is borne out twice: its front sight's post (US D631,934 S, drawn with the standard post at one setting) has its tip at 1.330 over the rail at the length's scale, so the pair co-witness on the drawings within 0.03 in; and Wing's two \"Center Height Over Rail\" figures are the patents' post tip (1.36) and this aperture leg's top (1.54). The end-on photo's 1.41 leans on where the channel's ceiling is under the screw's black and on a scale borrowed from the patent; it stays beside it as a conflict. Magpul's MBUS 3 rear has its aperture at 1.42 (\"Center of aperture to top of rail: 1.42 in.\"): Daniel Defense's sights are a lower pair."},"note":"The A2 aperture's centre, standing, over the rail's top (the channel's ceiling). No page states it: Midway (Daniel Defense's text) says \"The fixed rear sight is of the correct height for proper alignment with an A2 Rifle or M4 \"F\" Marked Front Sight Base, as well as for co-witnessing with a red dot optic\"; TLO and Alexander's \"Absolute Cowitness\". Wing's \"Center Height Over Rail: Front: 1.36\" Rear: 1.54\"\" are the tops of the two sighting pieces as the patents draw them: the front post's tip 1.330 (the front sight's ledger; Wing's 1.36) and this aperture leg's top 1.548 (the patent's centre 1.363 and the leg's top 0.185 over it): recorded under wing_center_height."},"wing_center_height":{"label":"Wing's \"Center Height Over Rail\" for the rear: the aperture leg's top","kind":"length","measurements":[{"id":"wing","value":1.54,"unit":"in","stated":"Center Height Over Rail: Front: 1.36\" Rear: 1.54\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Daniel Defense AR-15 Fixed Iron Sights (the set 19-088-09116; its spec list gives each sight)","url":"https://www.wingtactical.com/accessories/optics-sights/sights/daniel-defense-ar-15-fixed-iron-sights/","retrieved":"2026-10-19","via":"harvest"}}],"note":"Kept as the seller wrote it. It is no centre: the patent has the aperture leg's top 1.548 over the rail (its centre 1.363 and the leg's round top 0.185 above it), and the front's \"1.36\" in the same row is that sight's post tip (its patent draws it at 1.330 at the length's scale). What Wing calls a centre height is the sighting piece's top on each."},"aperture_large_d":{"label":"The large aperture's hole","kind":"length","measurements":[{"id":"tlo","value":0.2,"unit":"in","pm":0.0005,"stated":"Apertures: Small 0.070\" / Large 0.200\"","source":{"type":"spec","publisher":"retailer","name":"TLO Outdoors, Daniel Defense A1.5 Fixed Rear Sight, Rock & Lock (specifications list; not a seller on file)","url":"https://tlooutdoors.com/products/dd-a1-5-fixed-rear-sight","retrieved":"2026-10-19","via":"harvest"}},{"id":"alexanders","value":0.2,"unit":"in","pm":0.0005,"stated":"Aperture: Dual Aperture (0.070 in and 0.200 in)","source":{"type":"spec","publisher":"retailer","name":"Alexander's, Daniel Defense A1.5 Fixed Rear Sight, Key Specifications","url":"https://alexandersstore.com/product/dd-a1-5-fixed-rear-sight/","retrieved":"2026-10-19","via":"harvest"}}],"adopt":{"from":"alexanders","reason":"Two sellers agree; Alexander's is a seller on file."}},"aperture_small_d":{"label":"The small aperture's hole","kind":"length","measurements":[{"id":"tlo","value":0.07,"unit":"in","pm":0.0005,"stated":"Apertures: Small 0.070\" / Large 0.200\"","source":{"type":"spec","publisher":"retailer","name":"TLO Outdoors, Daniel Defense A1.5 Fixed Rear Sight, Rock & Lock (specifications list; not a seller on file)","url":"https://tlooutdoors.com/products/dd-a1-5-fixed-rear-sight","retrieved":"2026-10-19","via":"harvest"}},{"id":"alexanders","value":0.07,"unit":"in","pm":0.0005,"stated":"Aperture: Dual Aperture (0.070 in and 0.200 in)","source":{"type":"spec","publisher":"retailer","name":"Alexander's, Daniel Defense A1.5 Fixed Rear Sight, Key Specifications","url":"https://alexandersstore.com/product/dd-a1-5-fixed-rear-sight/","retrieved":"2026-10-19","via":"harvest"}}],"adopt":{"from":"alexanders","reason":"Two sellers agree; Alexander's is a seller on file."}},"clamp_length":{"label":"Clamp's length along the rail","kind":"length","measurements":[{"id":"derived","value":1.38,"unit":"in","source":{"type":"derived","expr":"{.length}","via":"harvest"}}],"note":"The base sits on the rail its whole length; its jaws hook under the rail's head from the front face back to the relief, 1.03 in."},"clamp_below_rail":{"label":"Clamp's reach below the rail's top (the jaws' feet)","kind":"length","measurements":[{"id":"patent","value":0.228,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight 19d661203cc6 (US D631,935 S, FIG. 4, the rear view from the breech; the patent office's copy, page 5, 300 dpi)","scaleRef":"the overall height, wall tops (row 609) to the feet (row 2608): 1999 px for daniel-defense-fixed-rear-sight.height_drawn (1105.5 px/in)","method":"the channel's ceiling (row 2356) to the feet (row 2608): 252 px. Wing's end-on photo has 0.114 of the height there (0.206 in at the same height)","via":"harvest"}}]},"front_x":{"label":"Base's front face ahead of the clamp's middle (x)","kind":"length","measurements":[{"id":"derived","value":0.69,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{.length} / 2","via":"harvest"},"note":"Where the side and plan profiles' origin (the base's front face) sits in the part frame."}]},"clamp_bottom_y":{"label":"Clamp's bottom in the sight's frame (y, the rail's top is 0)","kind":"length","measurements":[{"id":"derived","value":-0.228,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"-{.clamp_below_rail}","via":"harvest"},"note":"Where the side and end profiles' origin (the feet) sits in the part frame."}]},"screw_behind_front":{"label":"Clamp screw's axis behind the front face","kind":"length","measurements":[{"id":"patent","value":0.293,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight 2b28fd900eb7 (US D631,935 S, FIG. 5, the drum side, \"the muzzle end of the firearm ... to the viewer's right\"; the patent office's copy, page 6, 300 dpi)","scaleRef":"daniel-defense-fixed-rear-sight.length = 1.38 in: the front face (u 1937.5) to the rear end (u 487.5), 1450 px (1050.7 px/in)","method":"the screw head's circle (columns 1429 and 1831 along row 2364, rows 2163 and 2568 down column 1628: centre u 1630, v 2366) behind the front face: 307.5 px. The left side (FIG. 6) has the insert's centre 0.30 in behind its front face","via":"harvest"}},{"id":"photo","value":0.285,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight 064dcbc2239c (Primary Arms 19-064-11002_01, the drum side square on, 2200 px)","scaleRef":"the base's length on row 1000, 662 to 1512 (850 px) for 1.38 in","method":"the screw head's circle (columns 1222 to 1450, rows 1105 to 1322) behind the front face: 176 px","via":"harvest"}}],"adopt":{"from":"patent","reason":"The drawing the model is built from; the maker's photo agrees within 0.01 in."},"note":"The slotted screw crosses the channel in a groove in its ceiling and lies in a rail slot: it is where the sight is held against a slot. Midway: \"attaches easily to any Picatinny-Spec rail with a single slotted screw\"."},"screw_below_rail":{"label":"Clamp screw's axis below the rail's top","kind":"length","measurements":[{"id":"patent","value":0.015,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight 2b28fd900eb7 (US D631,935 S, FIG. 5, the drum side, \"the muzzle end of the firearm ... to the viewer's right\"; the patent office's copy, page 6, 300 dpi)","scaleRef":"daniel-defense-fixed-rear-sight.length = 1.38 in: the front face (u 1937.5) to the rear end (u 487.5), 1450 px (1050.7 px/in)","method":"the head's centre (v 2366) below the rail's top as the rear view places it over the feet (v 2589.5 less clamp_below_rail: v 2349.9): 16 px","via":"harvest"}}]},"screw_head_d":{"label":"Clamp screw's head","kind":"length","measurements":[{"id":"patent","value":0.384,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight 2b28fd900eb7 (US D631,935 S, FIG. 5, the drum side, \"the muzzle end of the firearm ... to the viewer's right\"; the patent office's copy, page 6, 300 dpi)","scaleRef":"daniel-defense-fixed-rear-sight.length = 1.38 in: the front face (u 1937.5) to the rear end (u 487.5), 1450 px (1050.7 px/in)","method":"the head's outer circle, 402 px across and 405 px down","via":"harvest"}},{"id":"photo","value":0.36,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight 064dcbc2239c (Primary Arms 19-064-11002_01)","scaleRef":"the base's length on row 1000, 850 px for 1.38 in","method":"the head's circle, 228 px across and 217 down","via":"harvest"}}],"adopt":{"from":"photo","reason":"The product as sold: the patent draws the head and its counterbore as one circle."}},"screw_head_proud":{"label":"Clamp screw's head beyond the right foot","kind":"length","measurements":[{"id":"patent","value":0.036,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight 19d661203cc6 (US D631,935 S, FIG. 4, the rear view from the breech; the patent office's copy, page 5, 300 dpi)","scaleRef":"the overall height, wall tops (row 609) to the feet (row 2608): 1999 px for daniel-defense-fixed-rear-sight.height_drawn (1105.5 px/in)","method":"the head's outer face (u 2016) beyond the right foot's (u 1977): 39.5 px","via":"harvest"}}]},"screw_d":{"label":"Clamp screw's shank","kind":"length","measurements":[{"id":"assumed","value":0.19,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no page names the screw. The rear view shows its thread 0.11 in under the ceiling (rows 2356 to 2479) and the side view its axis 0.015 under the rail's top, which makes it about 0.19 across; the sellers' photos show it filling a slot.","via":"harvest"}}],"note":"The screw's thread where it shows under the channel's ceiling, and its axis just under the rail's top: a shank that lies in a rail slot (0.206 in wide)."},"wall_top_above_rail":{"label":"Tower walls' top above the rail","kind":"length","measurements":[{"id":"patent","value":1.58,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight 19d661203cc6 (US D631,935 S, FIG. 4, the rear view from the breech; the patent office's copy, page 5, 300 dpi)","scaleRef":"the overall height, wall tops (row 609) to the feet (row 2608): 1999 px for daniel-defense-fixed-rear-sight.height_drawn (1105.5 px/in)","method":"the walls' top (row 609) over the channel's ceiling (row 2356): 1747 px","via":"harvest"}}]},"wall_thickness":{"label":"Tower walls' thickness","kind":"length","measurements":[{"id":"patent","value":0.101,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight 19d661203cc6 (US D631,935 S, FIG. 4, the rear view from the breech; the patent office's copy, page 5, 300 dpi)","scaleRef":"the overall height, wall tops (row 609) to the feet (row 2608): 1999 px for daniel-defense-fixed-rear-sight.height_drawn (1105.5 px/in)","method":"outer to inner face of each wall (u 836 to 947, 1618 to 1732): 111 and 114 px","via":"harvest"}}]},"body_width":{"label":"Body's width at the walls","kind":"length","measurements":[{"id":"patent","value":0.81,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight 19d661203cc6 (US D631,935 S, FIG. 4, the rear view from the breech; the patent office's copy, page 5, 300 dpi)","scaleRef":"the overall height, wall tops (row 609) to the feet (row 2608): 1999 px for daniel-defense-fixed-rear-sight.height_drawn (1105.5 px/in)","method":"the walls' outer faces (u 836 and 1732): 896 px","via":"harvest"}}]},"window_width":{"label":"Through-cut window's width","kind":"length","measurements":[{"id":"patent","value":0.691,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight 19d661203cc6 (US D631,935 S, FIG. 4, the rear view from the breech; the patent office's copy, page 5, 300 dpi)","scaleRef":"the overall height, wall tops (row 609) to the feet (row 2608): 1999 px for daniel-defense-fixed-rear-sight.height_drawn (1105.5 px/in)","method":"its sides along row 1800 (u 902 and 1666): 764 px","via":"harvest"}}],"note":"\"Through-cut design for weight savings\" (Primary Arms): a window through the body from end to end under the aperture, its corners rounded."},"window_height":{"label":"Through-cut window's height","kind":"length","measurements":[{"id":"patent","value":0.486,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight 19d661203cc6 (US D631,935 S, FIG. 4, the rear view from the breech; the patent office's copy, page 5, 300 dpi)","scaleRef":"the overall height, wall tops (row 609) to the feet (row 2608): 1999 px for daniel-defense-fixed-rear-sight.height_drawn (1105.5 px/in)","method":"its top and bottom down column 1000 (rows 1656 and 2193.5): 537.5 px","via":"harvest"}}]},"window_bottom_above_rail":{"label":"Through-cut window's floor above the rail","kind":"length","measurements":[{"id":"patent","value":0.147,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight 19d661203cc6 (US D631,935 S, FIG. 4, the rear view from the breech; the patent office's copy, page 5, 300 dpi)","scaleRef":"the overall height, wall tops (row 609) to the feet (row 2608): 1999 px for daniel-defense-fixed-rear-sight.height_drawn (1105.5 px/in)","method":"the window's floor (row 2193.5) over the channel's ceiling (row 2356): 162.5 px","via":"harvest"}}]},"slit_width":{"label":"The base's split under the window","kind":"length","measurements":[{"id":"patent","value":0.059,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight 19d661203cc6 (US D631,935 S, FIG. 4, the rear view from the breech; the patent office's copy, page 5, 300 dpi)","scaleRef":"the overall height, wall tops (row 609) to the feet (row 2608): 1999 px for daniel-defense-fixed-rear-sight.height_drawn (1105.5 px/in)","method":"the split's walls along row 2250 (u 1252 and 1317): 65 px","via":"harvest"}}],"note":"The base is split from the window's floor down to the channel (the patent's front and rear views, Wing's end-on photo): the screw draws its two halves onto the rail."},"drum_d":{"label":"Windage drum's diameter","kind":"length","measurements":[{"id":"patent","value":0.761,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight 19d661203cc6 (US D631,935 S, FIG. 4, the rear view from the breech; the patent office's copy, page 5, 300 dpi)","scaleRef":"the overall height, wall tops (row 609) to the feet (row 2608): 1999 px for daniel-defense-fixed-rear-sight.height_drawn (1105.5 px/in)","method":"the disc seen edge on, down column 1760 (rows 778 and 1619): 841 px. The side elevation's outer circle reads 0.782 at its own scale","via":"harvest"}},{"id":"photo","value":0.74,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight 064dcbc2239c (Primary Arms 19-064-11002_01)","scaleRef":"the base's length on row 1000, 850 px for 1.38 in","method":"the dark disc, columns 930 to 1394 and rows 344 to 794 (464 and 450 px)","via":"harvest"}}],"adopt":{"from":"photo","reason":"The product as sold, square on; the patent's two views of the disc differ by 0.02 in themselves."},"note":"\"an A1-Type Windage Wheel that requires a bullet tip or similar tool for adjustment\" (Midway): a disc with five holes and the numerals 1 to 5 on the sight's right."},"drum_proud":{"label":"Windage drum's face beyond the right wall","kind":"length","measurements":[{"id":"patent","value":0.043,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight 19d661203cc6 (US D631,935 S, FIG. 4, the rear view from the breech; the patent office's copy, page 5, 300 dpi)","scaleRef":"the overall height, wall tops (row 609) to the feet (row 2608): 1999 px for daniel-defense-fixed-rear-sight.height_drawn (1105.5 px/in)","method":"the disc's outer face (u 1779.5) beyond the wall's (u 1732): 47.5 px","via":"harvest"}}]},"drum_behind_front":{"label":"Windage drum's centre behind the front face","kind":"length","measurements":[{"id":"patent","value":0.582,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight 2b28fd900eb7 (US D631,935 S, FIG. 5, the drum side, \"the muzzle end of the firearm ... to the viewer's right\"; the patent office's copy, page 6, 300 dpi)","scaleRef":"daniel-defense-fixed-rear-sight.length = 1.38 in: the front face (u 1937.5) to the rear end (u 487.5), 1450 px (1050.7 px/in)","method":"the outer circle's centre (columns 915 and 1737 along row 1253; rows 842.5 and 1664 down column 1320: u 1326, v 1253) behind the front face: 611.5 px","via":"harvest"}},{"id":"photo","value":0.567,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight 064dcbc2239c (Primary Arms 19-064-11002_01)","scaleRef":"the base's length on row 1000, 850 px for 1.38 in","method":"the disc's centre (u 1162) behind the front face (u 1512): 350 px","via":"harvest"}}],"adopt":{"from":"patent","reason":"The drawing the model is built from; the photo agrees within 0.015 in."}},"drum_above_rail":{"label":"Windage drum's centre above the rail","kind":"length","measurements":[{"id":"patent","value":1.047,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight 19d661203cc6 (US D631,935 S, FIG. 4, the rear view from the breech; the patent office's copy, page 5, 300 dpi)","scaleRef":"the overall height, wall tops (row 609) to the feet (row 2608): 1999 px for daniel-defense-fixed-rear-sight.height_drawn (1105.5 px/in)","method":"the disc's middle (row 1198.5) over the channel's ceiling (row 2356): 1157.5 px. The side elevation has 1.044","via":"harvest"}}]},"hub_d":{"label":"Drum's hub (the windage screw's head) across","kind":"length","measurements":[{"id":"patent","value":0.273,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight 19d661203cc6 (US D631,935 S, FIG. 4, the rear view from the breech; the patent office's copy, page 5, 300 dpi)","scaleRef":"the overall height, wall tops (row 609) to the feet (row 2608): 1999 px for daniel-defense-fixed-rear-sight.height_drawn (1105.5 px/in)","method":"the hub down column 1830 (rows 1048.5 and 1351): 302.5 px. The side elevation's hub circle is 286 px at its scale, 0.272","via":"harvest"}}]},"hub_proud":{"label":"Drum's hub beyond the right wall","kind":"length","measurements":[{"id":"patent","value":0.22,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight 19d661203cc6 (US D631,935 S, FIG. 4, the rear view from the breech; the patent office's copy, page 5, 300 dpi)","scaleRef":"the overall height, wall tops (row 609) to the feet (row 2608): 1999 px for daniel-defense-fixed-rear-sight.height_drawn (1105.5 px/in)","method":"the hub's end (u 1975) beyond the wall's face (u 1732): 243 px","via":"harvest"}}]},"left_head_proud":{"label":"Windage screw's slotted end beyond the left wall","kind":"length","measurements":[{"id":"patent","value":0.058,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight 19d661203cc6 (US D631,935 S, FIG. 4, the rear view from the breech; the patent office's copy, page 5, 300 dpi)","scaleRef":"the overall height, wall tops (row 609) to the feet (row 2608): 1999 px for daniel-defense-fixed-rear-sight.height_drawn (1105.5 px/in)","method":"the head's outer face (u 772) beyond the wall's (u 836): 64 px","via":"harvest"}}]},"left_head_d":{"label":"Windage screw's slotted end across","kind":"length","measurements":[{"id":"patent","value":0.38,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight 1f6ea470414f (US D631,935 S, FIG. 6, the insert side, the muzzle to the viewer's left; page 7, 300 dpi)","scaleRef":"its own length, the front face (u 528) to the rear end (u 2010), 1482 px for 1.38 in (1074 px/in)","method":"the slotted head's outer circle, about 408 px across (u 950 to 1358, v 967 to 1375)","via":"harvest"}}]},"aperture_leg_width":{"label":"Aperture's standing leg across","kind":"length","measurements":[{"id":"patent","value":0.361,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight 19d661203cc6 (US D631,935 S, FIG. 4, the rear view from the breech; the patent office's copy, page 5, 300 dpi)","scaleRef":"the overall height, wall tops (row 609) to the feet (row 2608): 1999 px for daniel-defense-fixed-rear-sight.height_drawn (1105.5 px/in)","method":"the leg's sides along row 855 (u 1082 and 1481.5): 399.5 px. The large hole in it reads 216 px, 0.195 in: the published 0.200 within 2.5%, a check on this view's scale","via":"harvest"}}]},"aperture_leg_top":{"label":"Aperture leg's top above its hole's centre","kind":"length","measurements":[{"id":"patent","value":0.185,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight 19d661203cc6 (US D631,935 S, FIG. 4, the rear view from the breech; the patent office's copy, page 5, 300 dpi)","scaleRef":"the overall height, wall tops (row 609) to the feet (row 2608): 1999 px for daniel-defense-fixed-rear-sight.height_drawn (1105.5 px/in)","method":"the leg's round top (row 645, column 1300) above the hole's centre (row 849): 204 px","via":"harvest"}},{"id":"photo","value":0.173,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight f974783e231b (Wing Tactical 55197, the sight from behind)","scaleRef":"the overall height, 605 px for height_drawn (1.808 in)","method":"the leg's top (row 342, column 905) above the hole's centre (row 400): 58 px","via":"harvest"}}],"adopt":{"from":"patent","reason":"The drawing the sight line is adopted from; with it the leg's top is 1.548 over the rail, Wing's \"Rear: 1.54\". The photo's 0.173 stays beside it."}},"aperture_leg_thick":{"label":"Aperture legs' thickness along the rail","kind":"length","measurements":[{"id":"assumed","value":0.09,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the top view (FIG. 7) draws the standing leg about 0.1 in thick along the rail between the windage screw's threads, under hatching that hides its edges; the A2 aperture's own drawing isn't on file.","via":"harvest"}}]},"aperture_lying_reach":{"label":"The lying aperture leg's reach from the windage screw's axis","kind":"length","measurements":[{"id":"assumed","value":0.28,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the top view (FIG. 7) and Primary Arms' three-quarter photos (adc34e7a2d9f, 86d9f645ef0f) show the small aperture's leg lying flat under the standing one, about as long as the standing leg stands above the screw.","via":"harvest"}}]},"drum_hole_d":{"label":"Windage drum's holes (for a bullet's tip)","kind":"length","measurements":[{"id":"photo","value":0.1,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight 064dcbc2239c (Primary Arms 19-064-11002_01, the drum square on)","scaleRef":"the base's length on row 1000, 850 px for 1.38 in","method":"the five dark holes, about 61 px across each","via":"harvest"}},{"id":"patent","value":0.12,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight 2b28fd900eb7 (US D631,935 S, FIG. 5, the drum side, \"the muzzle end of the firearm ... to the viewer's right\"; the patent office's copy, page 6, 300 dpi)","scaleRef":"daniel-defense-fixed-rear-sight.length = 1.38 in: the front face (u 1937.5) to the rear end (u 487.5), 1450 px (1050.7 px/in)","method":"the holes' circles, 116 to 133 px across","via":"harvest"}}],"adopt":{"from":"photo","reason":"The product as sold; the patent draws the drum 5% larger too."}},"drum_hole_circle_d":{"label":"Windage drum's holes: the circle their centres lie on","kind":"length","measurements":[{"id":"photo","value":0.546,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight 064dcbc2239c (Primary Arms 19-064-11002_01)","scaleRef":"the base's length on row 1000, 850 px for 1.38 in","method":"the upper left hole's centre (u 1063, v 433) from the drum's (u 1162, v 569): 168 px, as a radius","via":"harvest"}},{"id":"patent","value":0.548,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight 2b28fd900eb7 (US D631,935 S, FIG. 5, the drum side, \"the muzzle end of the firearm ... to the viewer's right\"; the patent office's copy, page 6, 300 dpi)","scaleRef":"daniel-defense-fixed-rear-sight.length = 1.38 in: the front face (u 1937.5) to the rear end (u 487.5), 1450 px (1050.7 px/in)","method":"the holes by the numerals 1 and 3 (centres u 1496 v 1012, u 1325 v 1533) from the drum's centre (u 1326, v 1253): 295 and 280 px, as radii","via":"harvest"}}],"adopt":{"from":"photo","reason":"The product as sold; the two agree."}},"insert_d":{"label":"Thread insert's red rim across","kind":"length","measurements":[{"id":"photo","value":0.2,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight 22739368dfff (Primary Arms 19-064-11002_03, the left side square on)","scaleRef":"its framing is _01's (the same 2200 px series, the base 850 px long for 1.38 in)","method":"the red ring round the screw's end, about 121 px across","via":"harvest"}}]},"pocket_length":{"label":"The pocket under the aperture, along the rail","kind":"length","measurements":[{"id":"patent","value":0.627,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight f51e9e16d9a9 (US D631,935 S, FIG. 7, the top view; page 8, 300 dpi)","scaleRef":"its own length, the rear end (u 445.5) to the front face (u 1948), 1502.5 px for 1.38 in (1088.8 px/in)","method":"the broken-line rounded rectangle's ends (u 975 and 1658): 683 px; its middle (u 1316.5) 0.58 in behind the front face, over the drum's axis","via":"harvest"}}],"note":"The top view (FIG. 7) draws a rounded pocket in broken lines under the U's floor round the aperture's foot and the windage screw: hidden, so only its outline is drawn."},"pocket_width":{"label":"The pocket under the aperture, across","kind":"length","measurements":[{"id":"patent","value":0.467,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/daniel-defense-fixed-rear-sight f51e9e16d9a9 (US D631,935 S, FIG. 7, the top view; page 8, 300 dpi)","scaleRef":"its own length, 1502.5 px for 1.38 in (1088.8 px/in)","method":"the broken-line rounded rectangle's sides (v 1367 and 1875): 508 px","via":"harvest"}}]},"pocket_depth":{"label":"The pocket under the aperture, its depth under the U's floor","kind":"length","measurements":[{"id":"assumed","value":0.42,"unit":"in","pm":0.08,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view gives the pocket's depth. Taken down to a web over the window's top, which brings the model's metal (6061 at std.density.aluminium, the hardware as std.density.steel) to 1.81 oz, between the maker's 1.7 and Wing's 1.80; without it the model weighs 2.0.","via":"harvest"}}]}}},{"subject":"dead-air-rxd22ti","title":"Dead Air RXD22Ti rimfire suppressor (RXD22TiBLK, RXD22TiBB)","dimensions":{"overall_length_with_mount":{"label":"Overall length on its XRF brake (the XRF's rear face to the front cap ring)","kind":"length","measurements":[{"id":"dead-air","value":5.6,"unit":"in","pm":0.05,"stated":"Length 5.6\"","source":{"type":"spec","publisher":"manufacturer","name":"Dead Air Silencers, RXD22Ti (its Specifications)","url":"https://deadairsilencers.com/rxd22ti/","retrieved":"2026-11-06","via":"harvest"}},{"id":"fitment","value":5.6,"unit":"in","pm":0.05,"stated":"RXD22Ti 6AL4V Titanium, 17-4 Stainless Steel 5.6”/5.6oz (w/XRF Muzzle Device)","source":{"type":"spec","publisher":"manufacturer","name":"Dead Air Silencers, Fitment Guide (its table of models; references/dead-air-rxd22ti/docs/6643a554d1.pdf)","url":"https://deadairsilencers.com/content/pdfs/Fitment-Guide-Booklet-Web.pdf","retrieved":"2026-11-06","via":"harvest"}},{"id":"ruger","value":5.6,"unit":"in","pm":0.05,"stated":"5.6\" x 1.1\"","source":{"type":"spec","publisher":"manufacturer","name":"Ruger, RXD22Ti (the RXD line's page)","url":"https://ruger.com/micros/RXD/rxd22ti.html","retrieved":"2026-11-06","via":"harvest"}},{"id":"silencer-shop","value":5.6,"unit":"in","pm":0.05,"stated":"Length 5.6\" (with XRF mount)","source":{"type":"spec","publisher":"retailer","name":"Silencer Shop, dealer support article RXD 22Ti","url":"https://dealersupport.silencershop.com/en/articles/15014441-rxd-22ti","retrieved":"2026-11-06","via":"harvest"}}],"adopt":{"from":"fitment","reason":"Dead Air's fitment guide says what the length is of (with the XRF); its page, Ruger's and a dealer's say the same 5.6."}},"od":{"label":"Largest outside diameter (the tube)","kind":"length","measurements":[{"id":"dead-air","value":1.1,"unit":"in","pm":0.05,"stated":"Diameter 1.1\"","source":{"type":"spec","publisher":"manufacturer","name":"Dead Air Silencers, RXD22Ti (its Specifications)","url":"https://deadairsilencers.com/rxd22ti/","retrieved":"2026-11-06","via":"harvest"}},{"id":"ruger","value":1.1,"unit":"in","pm":0.05,"stated":"5.6\" x 1.1\"","source":{"type":"spec","publisher":"manufacturer","name":"Ruger, RXD22Ti (the RXD line's page)","url":"https://ruger.com/micros/RXD/rxd22ti.html","retrieved":"2026-11-06","via":"harvest"}},{"id":"silencer-shop","value":1.1,"unit":"in","pm":0.05,"stated":"Diameter 1.1\"","source":{"type":"spec","publisher":"retailer","name":"Silencer Shop, dealer support article RXD 22Ti","url":"https://dealersupport.silencershop.com/en/articles/15014441-rxd-22ti","retrieved":"2026-11-06","via":"harvest"}}],"adopt":{"from":"dead-air","reason":"The maker's page; Ruger's and a dealer's say the same."}},"weight_with_mount":{"label":"Weight on its XRF brake","kind":"mass","measurements":[{"id":"dead-air","value":5.6,"unit":"oz","pm":0.05,"stated":"Weight 5.6 Oz","source":{"type":"spec","publisher":"manufacturer","name":"Dead Air Silencers, RXD22Ti (its Specifications)","url":"https://deadairsilencers.com/rxd22ti/","retrieved":"2026-11-06","via":"harvest"}},{"id":"fitment","value":5.6,"unit":"oz","pm":0.05,"stated":"5.6”/5.6oz (w/XRF Muzzle Device)","source":{"type":"spec","publisher":"manufacturer","name":"Dead Air Silencers, Fitment Guide (its table of models; references/dead-air-rxd22ti/docs/6643a554d1.pdf)","url":"https://deadairsilencers.com/content/pdfs/Fitment-Guide-Booklet-Web.pdf","retrieved":"2026-11-06","via":"harvest"}},{"id":"ruger","value":5.6,"unit":"oz","pm":0.05,"stated":"5.6 oz (with XRF muzzle device)","source":{"type":"spec","publisher":"manufacturer","name":"Ruger, RXD22Ti (the RXD line's page)","url":"https://ruger.com/micros/RXD/rxd22ti.html","retrieved":"2026-11-06","via":"harvest"}}],"adopt":{"from":"fitment","reason":"Dead Air's guide says it is with the XRF; its page and Ruger's say the same 5.6."}},"weight":{"label":"Weight (the suppressor alone, without its XRF brake)","kind":"mass","measurements":[{"id":"ruger","value":4.6,"unit":"oz","pm":0.05,"stated":"4.6 oz (no muzzle device)","source":{"type":"spec","publisher":"manufacturer","name":"Ruger, RXD22Ti (the RXD line's page)","url":"https://ruger.com/micros/RXD/rxd22ti.html","retrieved":"2026-11-06","via":"harvest"}},{"id":"american-hunter","value":4.6,"unit":"oz","pm":0.05,"stated":"5.6 ozs. (with mount); 4.6 ozs. (no mount)","source":{"type":"spec","publisher":"review","name":"American Hunter, First Look: RXD Suppressors","url":"https://www.americanhunter.org/content/first-look-rxd-suppressors/","retrieved":"2026-11-06","via":"harvest"}},{"id":"less-mount","value":4.55,"unit":"oz","pm":0.06,"source":{"type":"derived","expr":"{.weight_with_mount} - {dead-air-xrf-brake.weight}","via":"harvest"},"note":"Dead Air's 5.6 oz with the XRF less the XRF's own 1.05 oz."}],"adopt":{"from":"ruger","reason":"Ruger's figure for the suppressor without its mount; the review says the same, and the maker's two figures (5.6 with, 1.05 for the XRF) come to 4.55."}},"length":{"label":"Length, rear face (the core's flange) to the front cap ring's front","kind":"length","measurements":[{"id":"on-mount","value":5.403,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{.overall_length_with_mount} - {dead-air-xrf-brake.suppressor_seat_x}","via":"harvest"}}],"note":"What the build adds ahead of the XRF's seat. On the photo of the pair: column 125 to 1422, 5.40 in."},"flange_end_x":{"label":"The core's rear flange, its front edge (the tube's rear face), from the rear face","kind":"length","measurements":[{"id":"photo","value":0.121,"unit":"in","pm":0.013,"source":{"type":"photo","photo":"references/dead-air-rxd22ti e5d4c6005c19 (Midwest Gun Works, RXD22TIBLK on its XRF, straight side view, rear at the left, 1500 x 1500, on white)","scaleRef":"along: Dead Air's 5.6 in over the pair's silhouette, columns 78 to 1422 (240.2 px/in); across: the tube's 256 px as the published 1.1 in (232.7 px/in)","method":"the silhouette's height column by column at a level of 235 of 255; stations where the height changes, (column - 125) / 240.2 from the core's rear face (± 3 px, 0.013 in); heights over 232.7 px/in (± 3 px, 0.013 in)","via":"harvest"},"note":"Columns 125 to 154."}]},"flange_chamfer_x":{"label":"The flange's rear chamfer ends (from the rear face)","kind":"length","measurements":[{"id":"photo","value":0.05,"unit":"in","pm":0.013,"source":{"type":"photo","photo":"references/dead-air-rxd22ti e5d4c6005c19 (Midwest Gun Works, RXD22TIBLK on its XRF, straight side view, rear at the left, 1500 x 1500, on white)","scaleRef":"along: Dead Air's 5.6 in over the pair's silhouette, columns 78 to 1422 (240.2 px/in); across: the tube's 256 px as the published 1.1 in (232.7 px/in)","method":"the silhouette's height column by column at a level of 235 of 255; stations where the height changes, (column - 125) / 240.2 from the core's rear face (± 3 px, 0.013 in); heights over 232.7 px/in (± 3 px, 0.013 in)","via":"harvest"},"note":"Columns 125 to 137: 210 to 236 px."}]},"flange_rear_d":{"label":"The flange's rear face, at the chamfer's foot","kind":"length","measurements":[{"id":"photo","value":0.902,"unit":"in","pm":0.013,"source":{"type":"photo","photo":"references/dead-air-rxd22ti e5d4c6005c19 (Midwest Gun Works, RXD22TIBLK on its XRF, straight side view, rear at the left, 1500 x 1500, on white)","scaleRef":"along: Dead Air's 5.6 in over the pair's silhouette, columns 78 to 1422 (240.2 px/in); across: the tube's 256 px as the published 1.1 in (232.7 px/in)","method":"the silhouette's height column by column at a level of 235 of 255; stations where the height changes, (column - 125) / 240.2 from the core's rear face (± 3 px, 0.013 in); heights over 232.7 px/in (± 3 px, 0.013 in)","via":"harvest"},"note":"210 px at column 125."}]},"flange_d":{"label":"The flange's corners (a hex, its corners turned)","kind":"length","measurements":[{"id":"photo","value":1.023,"unit":"in","pm":0.013,"source":{"type":"photo","photo":"references/dead-air-rxd22ti e5d4c6005c19 (Midwest Gun Works, RXD22TIBLK on its XRF, straight side view, rear at the left, 1500 x 1500, on white)","scaleRef":"along: Dead Air's 5.6 in over the pair's silhouette, columns 78 to 1422 (240.2 px/in); across: the tube's 256 px as the published 1.1 in (232.7 px/in)","method":"the silhouette's height column by column at a level of 235 of 255; stations where the height changes, (column - 125) / 240.2 from the core's rear face (± 3 px, 0.013 in); heights over 232.7 px/in (± 3 px, 0.013 in)","via":"harvest"},"note":"238 px, columns 138 to 154."}],"note":"A hex: on the photo of the pair its top flat is lit and its corners round off (and Ruger's exploded photos of the parts, 7b58ad4e444d and 0b575e192b3a, show its flats). Its flats aren't read (flange_flats)."},"flange_flats":{"label":"The flange's hex, across its flats","kind":"length","measurements":[{"id":"assumed","value":0.924,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.flange_d} * {.hex_flats} / {.hex_corner_d}","via":"harvest"},"note":"An assumption for the drawing, not a reading: the flange is too short on the photo for its faces to be read, and is drawn with the tube's hex's share of its corners."}]},"band_x":{"label":"The tube's rear band begins at full size (from the rear face)","kind":"length","measurements":[{"id":"photo","value":0.171,"unit":"in","pm":0.013,"source":{"type":"photo","photo":"references/dead-air-rxd22ti e5d4c6005c19 (Midwest Gun Works, RXD22TIBLK on its XRF, straight side view, rear at the left, 1500 x 1500, on white)","scaleRef":"along: Dead Air's 5.6 in over the pair's silhouette, columns 78 to 1422 (240.2 px/in); across: the tube's 256 px as the published 1.1 in (232.7 px/in)","method":"the silhouette's height column by column at a level of 235 of 255; stations where the height changes, (column - 125) / 240.2 from the core's rear face (± 3 px, 0.013 in); heights over 232.7 px/in (± 3 px, 0.013 in)","via":"harvest"},"note":"Column 166; its rear chamfer from column 155 (243 px, 0.125 in)."}]},"band_d":{"label":"The tube's rear band (round, engraved RXD RXD22Ti 22 CAL)","kind":"length","measurements":[{"id":"photo","value":1.117,"unit":"in","pm":0.013,"source":{"type":"photo","photo":"references/dead-air-rxd22ti e5d4c6005c19 (Midwest Gun Works, RXD22TIBLK on its XRF, straight side view, rear at the left, 1500 x 1500, on white)","scaleRef":"along: Dead Air's 5.6 in over the pair's silhouette, columns 78 to 1422 (240.2 px/in); across: the tube's 256 px as the published 1.1 in (232.7 px/in)","method":"the silhouette's height column by column at a level of 235 of 255; stations where the height changes, (column - 125) / 240.2 from the core's rear face (± 3 px, 0.013 in); heights over 232.7 px/in (± 3 px, 0.013 in)","via":"harvest"},"note":"259 to 261 px, columns 166 to 256: 4 px over the tube."}]},"band_end_x":{"label":"The rear band ends at a groove (from the rear face)","kind":"length","measurements":[{"id":"photo","value":0.55,"unit":"in","pm":0.013,"source":{"type":"photo","photo":"references/dead-air-rxd22ti e5d4c6005c19 (Midwest Gun Works, RXD22TIBLK on its XRF, straight side view, rear at the left, 1500 x 1500, on white)","scaleRef":"along: Dead Air's 5.6 in over the pair's silhouette, columns 78 to 1422 (240.2 px/in); across: the tube's 256 px as the published 1.1 in (232.7 px/in)","method":"the silhouette's height column by column at a level of 235 of 255; stations where the height changes, (column - 125) / 240.2 from the core's rear face (± 3 px, 0.013 in); heights over 232.7 px/in (± 3 px, 0.013 in)","via":"harvest"},"note":"Column 257."}]},"groove_d":{"label":"The grooves either side of the wrench hex","kind":"length","measurements":[{"id":"photo","value":1.087,"unit":"in","pm":0.013,"source":{"type":"photo","photo":"references/dead-air-rxd22ti e5d4c6005c19 (Midwest Gun Works, RXD22TIBLK on its XRF, straight side view, rear at the left, 1500 x 1500, on white)","scaleRef":"along: Dead Air's 5.6 in over the pair's silhouette, columns 78 to 1422 (240.2 px/in); across: the tube's 256 px as the published 1.1 in (232.7 px/in)","method":"the silhouette's height column by column at a level of 235 of 255; stations where the height changes, (column - 125) / 240.2 from the core's rear face (± 3 px, 0.013 in); heights over 232.7 px/in (± 3 px, 0.013 in)","via":"harvest"},"note":"253 px, columns 257 to 274 and 389 to 410."}]},"hex_x":{"label":"The tube's wrench hex begins (from the rear face)","kind":"length","measurements":[{"id":"photo","value":0.654,"unit":"in","pm":0.013,"source":{"type":"photo","photo":"references/dead-air-rxd22ti e5d4c6005c19 (Midwest Gun Works, RXD22TIBLK on its XRF, straight side view, rear at the left, 1500 x 1500, on white)","scaleRef":"along: Dead Air's 5.6 in over the pair's silhouette, columns 78 to 1422 (240.2 px/in); across: the tube's 256 px as the published 1.1 in (232.7 px/in)","method":"the silhouette's height column by column at a level of 235 of 255; stations where the height changes, (column - 125) / 240.2 from the core's rear face (± 3 px, 0.013 in); heights over 232.7 px/in (± 3 px, 0.013 in)","via":"harvest"},"note":"Column 282."}]},"hex_end_x":{"label":"The tube's wrench hex ends (from the rear face)","kind":"length","measurements":[{"id":"photo","value":1.045,"unit":"in","pm":0.013,"source":{"type":"photo","photo":"references/dead-air-rxd22ti e5d4c6005c19 (Midwest Gun Works, RXD22TIBLK on its XRF, straight side view, rear at the left, 1500 x 1500, on white)","scaleRef":"along: Dead Air's 5.6 in over the pair's silhouette, columns 78 to 1422 (240.2 px/in); across: the tube's 256 px as the published 1.1 in (232.7 px/in)","method":"the silhouette's height column by column at a level of 235 of 255; stations where the height changes, (column - 125) / 240.2 from the core's rear face (± 3 px, 0.013 in); heights over 232.7 px/in (± 3 px, 0.013 in)","via":"harvest"},"note":"Column 376."}]},"hex_corner_d":{"label":"The tube's wrench hex, its turned corners","kind":"length","measurements":[{"id":"photo","value":1.074,"unit":"in","pm":0.013,"source":{"type":"photo","photo":"references/dead-air-rxd22ti e5d4c6005c19 (Midwest Gun Works, RXD22TIBLK on its XRF, straight side view, rear at the left, 1500 x 1500, on white)","scaleRef":"along: Dead Air's 5.6 in over the pair's silhouette, columns 78 to 1422 (240.2 px/in); across: the tube's 256 px as the published 1.1 in (232.7 px/in)","method":"the silhouette's height column by column at a level of 235 of 255; stations where the height changes, (column - 125) / 240.2 from the core's rear face (± 3 px, 0.013 in); heights over 232.7 px/in (± 3 px, 0.013 in)","via":"harvest"},"note":"250 px, columns 282 to 376."}]},"hex_flats":{"label":"The tube's wrench hex, across its flats","kind":"length","measurements":[{"id":"photo","value":0.969,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/dead-air-rxd22ti e5d4c6005c19 (Midwest Gun Works, RXD22TIBLK on its XRF, straight side view, rear at the left, 1500 x 1500, on white)","scaleRef":"along: Dead Air's 5.6 in over the pair's silhouette, columns 78 to 1422 (240.2 px/in); across: the tube's 256 px as the published 1.1 in (232.7 px/in)","method":"the silhouette's height column by column at a level of 235 of 255; stations where the height changes, (column - 125) / 240.2 from the core's rear face (± 3 px, 0.013 in); heights over 232.7 px/in (± 3 px, 0.013 in)","via":"harvest"}}],"note":"A flat faces the lens: the faces show as bands down the hex, lit, dark and lit, 54, 108 and 60 px (rows 638, 692, 800, 860, by eye ± 6 px on a crop at 2.5 times), with the turned corners above and below (16 and 12 px). For flats at F/2 from the axis turned to a radius R, the face to the lens shows 2R sin a and each side face R sin a, where cos a = F/(2R): 108 = 250 sin a, a = 25.6 degrees, F = 0.902 of the corners. The manual names a 1-1/16 in and a 27 mm wrench for the core (p. 6): neither is this size, and no source says which flats they are for."},"tube_x":{"label":"The round tube begins (from the rear face)","kind":"length","measurements":[{"id":"photo","value":1.191,"unit":"in","pm":0.013,"source":{"type":"photo","photo":"references/dead-air-rxd22ti e5d4c6005c19 (Midwest Gun Works, RXD22TIBLK on its XRF, straight side view, rear at the left, 1500 x 1500, on white)","scaleRef":"along: Dead Air's 5.6 in over the pair's silhouette, columns 78 to 1422 (240.2 px/in); across: the tube's 256 px as the published 1.1 in (232.7 px/in)","method":"the silhouette's height column by column at a level of 235 of 255; stations where the height changes, (column - 125) / 240.2 from the core's rear face (± 3 px, 0.013 in); heights over 232.7 px/in (± 3 px, 0.013 in)","via":"harvest"},"note":"Column 411, after the groove (389 to 410)."}]},"flutes":{"label":"Flats down the tube","kind":"count","measurements":[{"id":"photo","value":8,"unit":"count","source":{"type":"photo","photo":"references/dead-air-rxd22ti e5d4c6005c19 (Midwest Gun Works, RXD22TIBLK on its XRF, straight side view, rear at the left, 1500 x 1500, on white)","scaleRef":"along: Dead Air's 5.6 in over the pair's silhouette, columns 78 to 1422 (240.2 px/in); across: the tube's 256 px as the published 1.1 in (232.7 px/in)","method":"the silhouette's height column by column at a level of 235 of 255; stations where the height changes, (column - 125) / 240.2 from the core's rear face (± 3 px, 0.013 in); heights over 232.7 px/in (± 3 px, 0.013 in)","via":"harvest"}}],"note":"Long flats, deeper toward the front (wedges: narrow at their rear end, square across at the front). On the photo of the pair the one to the lens is centred 2.5 degrees above the axis and the next two 40 and 43 degrees either side; on Soldier Systems' photo of the black one standing (aa413639ea63) three show at 0 and about 45 and 50 degrees either side; the top of the silhouette dips 2 to 4 px over columns 491 to 724, a flat just past the edge. 45 degrees apart: eight."},"flute_x":{"label":"The flats' rear ends (from the rear face)","kind":"length","measurements":[{"id":"photo","value":1.624,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/dead-air-rxd22ti e5d4c6005c19 (Midwest Gun Works, RXD22TIBLK on its XRF, straight side view, rear at the left, 1500 x 1500, on white)","scaleRef":"along: Dead Air's 5.6 in over the pair's silhouette, columns 78 to 1422 (240.2 px/in); across: the tube's 256 px as the published 1.1 in (232.7 px/in)","method":"the silhouette's height column by column at a level of 235 of 255; stations where the height changes, (column - 125) / 240.2 from the core's rear face (± 3 px, 0.013 in); heights over 232.7 px/in (± 3 px, 0.013 in)","via":"harvest"},"note":"Column 515, the point of the flat to the lens, by eye."}]},"flute_end_x":{"label":"The flats' front ends (from the rear face)","kind":"length","measurements":[{"id":"photo","value":3.351,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/dead-air-rxd22ti e5d4c6005c19 (Midwest Gun Works, RXD22TIBLK on its XRF, straight side view, rear at the left, 1500 x 1500, on white)","scaleRef":"along: Dead Air's 5.6 in over the pair's silhouette, columns 78 to 1422 (240.2 px/in); across: the tube's 256 px as the published 1.1 in (232.7 px/in)","method":"the silhouette's height column by column at a level of 235 of 255; stations where the height changes, (column - 125) / 240.2 from the core's rear face (± 3 px, 0.013 in); heights over 232.7 px/in (± 3 px, 0.013 in)","via":"harvest"},"note":"Column 930, the flat to the lens, by eye (its end runs a little slant across it)."}]},"flute_width":{"label":"A flat's width at its front end","kind":"length","measurements":[{"id":"photo","value":0.232,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/dead-air-rxd22ti e5d4c6005c19 (Midwest Gun Works, RXD22TIBLK on its XRF, straight side view, rear at the left, 1500 x 1500, on white)","scaleRef":"along: Dead Air's 5.6 in over the pair's silhouette, columns 78 to 1422 (240.2 px/in); across: the tube's 256 px as the published 1.1 in (232.7 px/in)","method":"the silhouette's height column by column at a level of 235 of 255; stations where the height changes, (column - 125) / 240.2 from the core's rear face (± 3 px, 0.013 in); heights over 232.7 px/in (± 3 px, 0.013 in)","via":"harvest"},"note":"The flat to the lens at its front end, rows 718 to 772, by eye."}],"note":"On a round of radius R a flat as wide as w is R - sqrt(R^2 - (w/2)^2) deep: 0.012 in here. The lit face is what shows of it."},"flute_depth":{"label":"A flat's depth at its front end","kind":"length","measurements":[{"id":"assumed","value":0.04,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: between the plane the width allows (0.012) and the depth the silhouette's dip implies (0.09); a groove of the radius that makes it flute_width wide at this depth.","via":"harvest"}}],"note":"Two readings that don't agree on one shape: a plane as wide as flute_width at the front is 0.012 in deep there; but where the flat next to the top crosses the silhouette's edge (columns 491 to 724, deepest 558 to 631, about 1.95 in from the rear face) the edge dips 4 px, 0.017 in, at a fifth of the flat's length, which deepening evenly would make 0.09 at its front. The flats read as clean facets in every photo (a lit face, a shadowed front wall), so they are drawn as shallow round grooves between the two."},"front_groove_x":{"label":"The ring groove round the tube near its front (from the rear face)","kind":"length","measurements":[{"id":"photo","value":4.933,"unit":"in","pm":0.013,"source":{"type":"photo","photo":"references/dead-air-rxd22ti e5d4c6005c19 (Midwest Gun Works, RXD22TIBLK on its XRF, straight side view, rear at the left, 1500 x 1500, on white)","scaleRef":"along: Dead Air's 5.6 in over the pair's silhouette, columns 78 to 1422 (240.2 px/in); across: the tube's 256 px as the published 1.1 in (232.7 px/in)","method":"the silhouette's height column by column at a level of 235 of 255; stations where the height changes, (column - 125) / 240.2 from the core's rear face (± 3 px, 0.013 in); heights over 232.7 px/in (± 3 px, 0.013 in)","via":"harvest"},"note":"Column 1310, a line round the tube on a crop at 2.5 times."}]},"front_groove_width":{"label":"The ring groove's width","kind":"length","measurements":[{"id":"photo","value":0.016,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/dead-air-rxd22ti e5d4c6005c19 (Midwest Gun Works, RXD22TIBLK on its XRF, straight side view, rear at the left, 1500 x 1500, on white)","scaleRef":"along: Dead Air's 5.6 in over the pair's silhouette, columns 78 to 1422 (240.2 px/in); across: the tube's 256 px as the published 1.1 in (232.7 px/in)","method":"the silhouette's height column by column at a level of 235 of 255; stations where the height changes, (column - 125) / 240.2 from the core's rear face (± 3 px, 0.013 in); heights over 232.7 px/in (± 3 px, 0.013 in)","via":"harvest"},"note":"About 4 px on a crop at 2.5 times (columns 1308 to 1312)."}],"note":"A fine line lit from one side: read as its lit wall and its shadow together (CLAUDE.md)."},"front_groove_depth":{"label":"The ring groove's depth","kind":"length","measurements":[{"id":"assumed","value":0.008,"unit":"in","pm":0.005,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: a V half as deep as it is wide; no view on file shows the groove in the silhouette.","via":"harvest"}}]},"ring_od":{"label":"The front cap ring's outside, where it stands out of the tube","kind":"length","measurements":[{"id":"photo","value":1.109,"unit":"in","pm":0.013,"source":{"type":"photo","photo":"references/dead-air-rxd22ti e5d4c6005c19 (Midwest Gun Works, RXD22TIBLK on its XRF, straight side view, rear at the left, 1500 x 1500, on white)","scaleRef":"along: Dead Air's 5.6 in over the pair's silhouette, columns 78 to 1422 (240.2 px/in); across: the tube's 256 px as the published 1.1 in (232.7 px/in)","method":"the silhouette's height column by column at a level of 235 of 255; stations where the height changes, (column - 125) / 240.2 from the core's rear face (± 3 px, 0.013 in); heights over 232.7 px/in (± 3 px, 0.013 in)","via":"harvest"},"note":"258 px, columns 1398 to 1409: the tube's own size; the seam between them is the line where the ring's black begins."}]},"tube_front_x":{"label":"The tube's front edge (from the rear face)","kind":"length","measurements":[{"id":"photo","value":5.3,"unit":"in","pm":0.013,"source":{"type":"photo","photo":"references/dead-air-rxd22ti e5d4c6005c19 (Midwest Gun Works, RXD22TIBLK on its XRF, straight side view, rear at the left, 1500 x 1500, on white)","scaleRef":"along: Dead Air's 5.6 in over the pair's silhouette, columns 78 to 1422 (240.2 px/in); across: the tube's 256 px as the published 1.1 in (232.7 px/in)","method":"the silhouette's height column by column at a level of 235 of 255; stations where the height changes, (column - 125) / 240.2 from the core's rear face (± 3 px, 0.013 in); heights over 232.7 px/in (± 3 px, 0.013 in)","via":"harvest"},"note":"Column 1398, where the front cap ring stands out of the tube."}]},"ring_notches":{"label":"Notches round the front cap ring's lip","kind":"count","measurements":[{"id":"photo","value":6,"unit":"count","source":{"type":"photo","photo":"references/dead-air-rxd22ti aa413639ea63 (Soldier Systems Daily, RXD22Ti in black standing, from a little above its front end, 3617 x 3618)","scaleRef":"the ring's own width (columns 1633 to 2040 at full size)","method":"each notch's middle across the ring, as the sine of its angle round from the lens","via":"harvest"}}],"note":"The manual: \"by laying a 3/32 Allen wrench across the groves on the Front Cap Ring\" (p. 8). On Soldier Systems' photo of the black one from just above its front end (aa413639ea63) notches stand at -78, -16 and +40 degrees round from the lens; on the photo of the pair at -17 and +38. 58 degrees apart: six."},"ring_notch_width":{"label":"A notch's width","kind":"length","measurements":[{"id":"photo","value":0.13,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/dead-air-rxd22ti aa413639ea63 (Soldier Systems Daily, RXD22Ti in black standing, from a little above its front end, 3617 x 3618)","scaleRef":"the ring's own width (columns 1633 to 2040 at full size)","method":"each notch's middle across the ring, as the sine of its angle round from the lens","via":"harvest"},"note":"The notch at -16 degrees on Soldier Systems' photo: 52 px of the ring's 407 there, square on, as 1.1 in."}]},"ring_notch_depth":{"label":"A notch's depth into the ring's lip","kind":"length","measurements":[{"id":"photo","value":0.05,"unit":"in","pm":0.013,"source":{"type":"photo","photo":"references/dead-air-rxd22ti e5d4c6005c19 (Midwest Gun Works, RXD22TIBLK on its XRF, straight side view, rear at the left, 1500 x 1500, on white)","scaleRef":"along: Dead Air's 5.6 in over the pair's silhouette, columns 78 to 1422 (240.2 px/in); across: the tube's 256 px as the published 1.1 in (232.7 px/in)","method":"the silhouette's height column by column at a level of 235 of 255; stations where the height changes, (column - 125) / 240.2 from the core's rear face (± 3 px, 0.013 in); heights over 232.7 px/in (± 3 px, 0.013 in)","via":"harvest"},"note":"The lip's edge steps 12 px at each notch (columns 1404 to 1416)."}]},"ring_front_round":{"label":"The ring's front outer edge, rounded","kind":"length","measurements":[{"id":"photo","value":0.02,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/dead-air-rxd22ti e5d4c6005c19 (Midwest Gun Works, RXD22TIBLK on its XRF, straight side view, rear at the left, 1500 x 1500, on white)","scaleRef":"along: Dead Air's 5.6 in over the pair's silhouette, columns 78 to 1422 (240.2 px/in); across: the tube's 256 px as the published 1.1 in (232.7 px/in)","method":"the silhouette's height column by column at a level of 235 of 255; stations where the height changes, (column - 125) / 240.2 from the core's rear face (± 3 px, 0.013 in); heights over 232.7 px/in (± 3 px, 0.013 in)","via":"harvest"},"note":"The silhouette's height falls from 245 to 159 px over the last 4 columns (1418 to 1421)."}]},"ring_bore_d":{"label":"The front cap ring's inside, round the core's front face","kind":"length","measurements":[{"id":"assumed","value":0.85,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file looks into the front end square on; Ruger's exploded photo (7b58ad4e444d) shows a ring a little over a tenth of its own width thick.","via":"harvest"}}]},"exit_bore_d":{"label":"The hole through the core's front face","kind":"length","measurements":[{"id":"assumed","value":0.26,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{dead-air-xrf-brake.bore_d}","via":"harvest"},"note":"An assumption for the drawing: the XRF's bore as read on its photo. Dead Air: \".22 Caliber\" bore (the fitment guide)."}]},"core_face_inset":{"label":"The core's front face behind the ring's front","kind":"length","measurements":[{"id":"assumed","value":0.1,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{.length} - {.tube_front_x}","via":"harvest"},"note":"An assumption for the drawing: the core's face drawn at the tube's front edge, as far in as the ring stands out of it."}]}}},{"subject":"dead-air-xrf-brake","title":"Dead Air XRF Xeno Rimfire Muzzle Brake, 1/2-28 (RXD674)","dimensions":{"overall_length":{"label":"Overall length, rear face to front face","kind":"length","measurements":[{"id":"dead-air","value":1.16,"unit":"in","pm":0.005,"stated":"Total Length 1/2-28 : 1.16\"","source":{"type":"spec","publisher":"manufacturer","name":"Dead Air Silencers, XRF Xeno Rimfire Muzzle Brake (its Specifications)","url":"https://deadairsilencers.com/xrf-xeno-rimfire-muzzle-brake/","retrieved":"2026-11-06","via":"harvest"}},{"id":"deguns","value":1.16,"unit":"in","pm":0.005,"stated":"Dead Air XRF Xeno Rimfire Muzzle Brake Black Nitride 17-4PH Stainless Steel 1/2\"x28 Threads 1.16\" OAL 0.81\" Diameter RXD674","source":{"type":"spec","publisher":"retailer","name":"DEGuns, Dead Air RXD674 (its title)","url":"https://www.deguns.com/dead-air-xrf-xeno-rimfire-muzzle-brake-black-nitride-17-4ph-stainless-steel-1-2-x28-threads-1-16-oal-0-81-diameter-rxd674","retrieved":"2026-11-06","via":"harvest"}}],"adopt":{"from":"dead-air","reason":"The maker's own page; a seller's title says the same."},"note":"Dead Air's page gives one line for its two threads: \"Total Length 1/2-28 : 1.16\" | M10x1 : 1.21\" (added length .66\")\". The \".66\" added length\" is in the M10x1 one's half of the line and isn't this item's; whether it is the M10x1's length ahead of a muzzle it seats on isn't said."},"length":{"label":"Length ahead of the barrel's shoulder, installed (to the front face)","kind":"length","measurements":[{"id":"shouldered","value":1.16,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{.overall_length}","via":"harvest"}}],"note":"The rear face bears on the shoulder (the manual, p. 6: \"until the rear of the XRF muzzle device mates to the shoulder of the barrel\"); no washer."},"od":{"label":"Largest outside diameter (the hex's corners, and the thread's crests)","kind":"length","measurements":[{"id":"dead-air","value":0.81,"unit":"in","pm":0.005,"stated":"Diameter 0.81\"","source":{"type":"spec","publisher":"manufacturer","name":"Dead Air Silencers, XRF Xeno Rimfire Muzzle Brake (its Specifications)","url":"https://deadairsilencers.com/xrf-xeno-rimfire-muzzle-brake/","retrieved":"2026-11-06","via":"harvest"}},{"id":"deguns","value":0.81,"unit":"in","pm":0.005,"stated":"0.81\" Diameter","source":{"type":"spec","publisher":"retailer","name":"DEGuns, Dead Air RXD674 (its title)","url":"https://www.deguns.com/dead-air-xrf-xeno-rimfire-muzzle-brake-black-nitride-17-4ph-stainless-steel-1-2-x28-threads-1-16-oal-0-81-diameter-rxd674","retrieved":"2026-11-06","via":"harvest"}}],"adopt":{"from":"dead-air","reason":"The maker's own page; a seller's title says the same."},"note":"Dead Air's one diameter; on the photo the hex (a flat to the lens, so its corners at the silhouette) reads 444 px and the thread's crests 446: the two are one size, 0.81."},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"dead-air","value":1.05,"unit":"oz","pm":0.005,"stated":"Weight 1/2-28 : 1.05 Oz | M10x1 : 1.22 Oz","source":{"type":"spec","publisher":"manufacturer","name":"Dead Air Silencers, XRF Xeno Rimfire Muzzle Brake (its Specifications)","url":"https://deadairsilencers.com/xrf-xeno-rimfire-muzzle-brake/","retrieved":"2026-11-06","via":"harvest"}},{"id":"deguns","value":1.05,"unit":"oz","pm":0.005,"stated":"Weight 1.05 oz","source":{"type":"spec","publisher":"retailer","name":"DEGuns, Dead Air RXD674 (its title)","url":"https://www.deguns.com/dead-air-xrf-xeno-rimfire-muzzle-brake-black-nitride-17-4ph-stainless-steel-1-2-x28-threads-1-16-oal-0-81-diameter-rxd674","retrieved":"2026-11-06","via":"harvest"}}],"adopt":{"from":"dead-air","reason":"The maker's own page; a seller's table says the same."}},"hex_flats":{"label":"The rear hex, across its flats","kind":"length","measurements":[{"id":"assumed","value":0.75,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the manual's 3/4 in wrench taken to be for this hex, whose corners are turned to the published 0.81 in diameter (Midwest Gun Works' photo, 8425e22cd635, shows the corners rounded off).","via":"harvest"}}],"note":"No source gives it, and no view on file looks along the axis. The manual names three wrenches for putting it on: \"Using a 1-1/16\", 27mm, and a 3/4\" wrench or the supplied RXD22Ti tools on the core, torque the muzzle device to the barrel at 20 foot-pounds.\" (p. 6); the 3/4 in one is the only size under the device's 0.81 in corners."},"hex_end_x":{"label":"The hex's front edge, from the rear face","kind":"length","measurements":[{"id":"photo","value":0.162,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/dead-air-xrf-brake 8425e22cd635 (Midwest Gun Works, RXD674 standing on its rear face, seen square from its side and 13 degrees from above, 1500 x 1500, on white)","scaleRef":"its published length, 1.16 in, over the axis from the front face's middle to the rear face's (627 px with the 13 degrees taken out: 540.5 px/in along); its published diameter, 0.81 in, over the hex's 444 px (548 px/in across)","method":"the silhouette's width row by row at a level of 235 of 255; a station is the row where the width changes, (1050.4 - row) / 610.4 x 1.16 from the rear face (± 4 px, 0.008 in); widths as read over 548 px/in (± 3 px, 0.006 in)","via":"harvest"},"note":"Row 965, where the hex's 444 px begin to fall."}]},"suppressor_seat_x":{"label":"Where the RXD22Ti's rear face stands when it is threaded on (from the rear face, the barrel's shoulder)","kind":"length","measurements":[{"id":"photo","value":0.197,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/dead-air-xrf-brake 8425e22cd635 (Midwest Gun Works, RXD674 standing on its rear face, seen square from its side and 13 degrees from above, 1500 x 1500, on white)","scaleRef":"its published length, 1.16 in, over the axis from the front face's middle to the rear face's (627 px with the 13 degrees taken out: 540.5 px/in along); its published diameter, 0.81 in, over the hex's 444 px (548 px/in across)","method":"the silhouette's width row by row at a level of 235 of 255; a station is the row where the width changes, (1050.4 - row) / 610.4 x 1.16 from the rear face (± 4 px, 0.008 in); widths as read over 548 px/in (± 3 px, 0.006 in)","via":"harvest"},"note":"Row 947, where the hex's front chamfer (444 to 408 px) ends."},{"id":"together","value":0.196,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/dead-air-rxd22ti e5d4c6005c19 (Midwest Gun Works, RXD22TIBLK on its XRF, straight side view, rear at the left, 1500 x 1500, on white)","scaleRef":"Dead Air's 5.6 in for the RXD22Ti with its XRF over the pair's 1345 px (columns 78 to 1422): 240.2 px/in","method":"the silhouette's height column by column at a level of 235: the XRF's hex from column 78 to 124 (its corners 190 px), the core's flange rising from 125","via":"harvest"}}],"adopt":{"from":"photo","reason":"Read on the device itself; the photo of the pair puts the core's face within a thousandth of it."},"note":"The core's rear face comes down to the front of the hex's chamfer: on this device's own photo the chamfer ends at row 947 (0.197 in); on Midwest Gun Works' photo of the two together (references/dead-air-rxd22ti e5d4c6005c19, the RXD22Ti on its XRF from the side, scaled by Dead Air's 5.6 in over the pair) the XRF shows 47 px behind the core's flange, 0.196 in. The manual: \"Thread the muzzle device onto your host firearm or into the suppressor until it bottoms out on the taper\" (p. 6): the seat that holds is the taper inside, and this face is where the core stops with it."},"groove_d":{"label":"The groove behind the thread (and the hex's chamfered front edge)","kind":"length","measurements":[{"id":"photo","value":0.75,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/dead-air-xrf-brake 8425e22cd635 (Midwest Gun Works, RXD674 standing on its rear face, seen square from its side and 13 degrees from above, 1500 x 1500, on white)","scaleRef":"its published length, 1.16 in, over the axis from the front face's middle to the rear face's (627 px with the 13 degrees taken out: 540.5 px/in along); its published diameter, 0.81 in, over the hex's 444 px (548 px/in across)","method":"the silhouette's width row by row at a level of 235 of 255; a station is the row where the width changes, (1050.4 - row) / 610.4 x 1.16 from the rear face (± 4 px, 0.008 in); widths as read over 548 px/in (± 3 px, 0.006 in)","via":"harvest"},"note":"Rows 940 to 946, 408 to 416 px; the chamfer ends at 408."}]},"thread_x":{"label":"The thread's crests begin (from the rear face)","kind":"length","measurements":[{"id":"photo","value":0.236,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/dead-air-xrf-brake 8425e22cd635 (Midwest Gun Works, RXD674 standing on its rear face, seen square from its side and 13 degrees from above, 1500 x 1500, on white)","scaleRef":"its published length, 1.16 in, over the axis from the front face's middle to the rear face's (627 px with the 13 degrees taken out: 540.5 px/in along); its published diameter, 0.81 in, over the hex's 444 px (548 px/in across)","method":"the silhouette's width row by row at a level of 235 of 255; a station is the row where the width changes, (1050.4 - row) / 610.4 x 1.16 from the rear face (± 4 px, 0.008 in); widths as read over 548 px/in (± 3 px, 0.006 in)","via":"harvest"},"note":"Row 926: the flank behind the first crest rises from the groove over rows 940 to 926."}]},"thread_end_x":{"label":"The thread's crests end (from the rear face)","kind":"length","measurements":[{"id":"photo","value":0.408,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/dead-air-xrf-brake 8425e22cd635 (Midwest Gun Works, RXD674 standing on its rear face, seen square from its side and 13 degrees from above, 1500 x 1500, on white)","scaleRef":"its published length, 1.16 in, over the axis from the front face's middle to the rear face's (627 px with the 13 degrees taken out: 540.5 px/in along); its published diameter, 0.81 in, over the hex's 444 px (548 px/in across)","method":"the silhouette's width row by row at a level of 235 of 255; a station is the row where the width changes, (1050.4 - row) / 610.4 x 1.16 from the rear face (± 4 px, 0.008 in); widths as read over 548 px/in (± 3 px, 0.006 in)","via":"harvest"},"note":"Row 836, where the lead-in ahead of the thread begins to fall."}]},"thread_major_d":{"label":"The thread the RXD22Ti's core screws onto, across its crests","kind":"length","measurements":[{"id":"photo","value":0.814,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/dead-air-xrf-brake 8425e22cd635 (Midwest Gun Works, RXD674 standing on its rear face, seen square from its side and 13 degrees from above, 1500 x 1500, on white)","scaleRef":"its published length, 1.16 in, over the axis from the front face's middle to the rear face's (627 px with the 13 degrees taken out: 540.5 px/in along); its published diameter, 0.81 in, over the hex's 444 px (548 px/in across)","method":"the silhouette's width row by row at a level of 235 of 255; a station is the row where the width changes, (1050.4 - row) / 610.4 x 1.16 from the rear face (± 4 px, 0.008 in); widths as read over 548 px/in (± 3 px, 0.006 in)","via":"harvest"},"note":"445 to 449 px over rows 836 to 925."}]},"thread_pitch":{"label":"The thread's pitch","kind":"length","measurements":[{"id":"photo","value":0.0375,"unit":"in","pm":0.002,"source":{"type":"photo","photo":"references/dead-air-xrf-brake 8425e22cd635 (Midwest Gun Works, RXD674 standing on its rear face, seen square from its side and 13 degrees from above, 1500 x 1500, on white)","scaleRef":"its published length, 1.16 in, over the axis from the front face's middle to the rear face's (627 px with the 13 degrees taken out: 540.5 px/in along); its published diameter, 0.81 in, over the hex's 444 px (548 px/in across)","method":"the silhouette's width row by row at a level of 235 of 255; a station is the row where the width changes, (1050.4 - row) / 610.4 x 1.16 from the rear face (± 4 px, 0.008 in); widths as read over 548 px/in (± 3 px, 0.006 in)","via":"harvest"}}],"note":"Not stated anywhere on file. The crests' tips on the silhouette's left edge (the column falls to 524 at rows 842, 863, 883, 902) are 19.7 px apart: 0.0375 in, 26.7 to the inch. Read as that; whether it is 28 or 27 to the inch isn't settled by this photo (18.8 or 19.5 px)."},"lead_end_x":{"label":"The lead-in ahead of the thread ends (from the rear face)","kind":"length","measurements":[{"id":"photo","value":0.462,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/dead-air-xrf-brake 8425e22cd635 (Midwest Gun Works, RXD674 standing on its rear face, seen square from its side and 13 degrees from above, 1500 x 1500, on white)","scaleRef":"its published length, 1.16 in, over the axis from the front face's middle to the rear face's (627 px with the 13 degrees taken out: 540.5 px/in along); its published diameter, 0.81 in, over the hex's 444 px (548 px/in across)","method":"the silhouette's width row by row at a level of 235 of 255; a station is the row where the width changes, (1050.4 - row) / 610.4 x 1.16 from the rear face (± 4 px, 0.008 in); widths as read over 548 px/in (± 3 px, 0.006 in)","via":"harvest"},"note":"Row 807: the width falls from 443 to 391 px over rows 836 to 807."}]},"neck_d":{"label":"The neck between the thread and the taper's collar","kind":"length","measurements":[{"id":"photo","value":0.71,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/dead-air-xrf-brake 8425e22cd635 (Midwest Gun Works, RXD674 standing on its rear face, seen square from its side and 13 degrees from above, 1500 x 1500, on white)","scaleRef":"its published length, 1.16 in, over the axis from the front face's middle to the rear face's (627 px with the 13 degrees taken out: 540.5 px/in along); its published diameter, 0.81 in, over the hex's 444 px (548 px/in across)","method":"the silhouette's width row by row at a level of 235 of 255; a station is the row where the width changes, (1050.4 - row) / 610.4 x 1.16 from the rear face (± 4 px, 0.008 in); widths as read over 548 px/in (± 3 px, 0.006 in)","via":"harvest"},"note":"389 px, rows 778 to 806."}]},"collar_x":{"label":"The taper's collar begins (from the rear face)","kind":"length","measurements":[{"id":"photo","value":0.519,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/dead-air-xrf-brake 8425e22cd635 (Midwest Gun Works, RXD674 standing on its rear face, seen square from its side and 13 degrees from above, 1500 x 1500, on white)","scaleRef":"its published length, 1.16 in, over the axis from the front face's middle to the rear face's (627 px with the 13 degrees taken out: 540.5 px/in along); its published diameter, 0.81 in, over the hex's 444 px (548 px/in across)","method":"the silhouette's width row by row at a level of 235 of 255; a station is the row where the width changes, (1050.4 - row) / 610.4 x 1.16 from the rear face (± 4 px, 0.008 in); widths as read over 548 px/in (± 3 px, 0.006 in)","via":"harvest"},"note":"Row 777; a small chamfer over rows 770 to 777."}]},"collar_d":{"label":"The taper's collar, the widest of the taper","kind":"length","measurements":[{"id":"photo","value":0.737,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/dead-air-xrf-brake 8425e22cd635 (Midwest Gun Works, RXD674 standing on its rear face, seen square from its side and 13 degrees from above, 1500 x 1500, on white)","scaleRef":"its published length, 1.16 in, over the axis from the front face's middle to the rear face's (627 px with the 13 degrees taken out: 540.5 px/in along); its published diameter, 0.81 in, over the hex's 444 px (548 px/in across)","method":"the silhouette's width row by row at a level of 235 of 255; a station is the row where the width changes, (1050.4 - row) / 610.4 x 1.16 from the rear face (± 4 px, 0.008 in); widths as read over 548 px/in (± 3 px, 0.006 in)","via":"harvest"},"note":"404 px, rows 747 to 769."}]},"taper_x":{"label":"The taper begins, at the collar's front (from the rear face)","kind":"length","measurements":[{"id":"photo","value":0.576,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/dead-air-xrf-brake 8425e22cd635 (Midwest Gun Works, RXD674 standing on its rear face, seen square from its side and 13 degrees from above, 1500 x 1500, on white)","scaleRef":"its published length, 1.16 in, over the axis from the front face's middle to the rear face's (627 px with the 13 degrees taken out: 540.5 px/in along); its published diameter, 0.81 in, over the hex's 444 px (548 px/in across)","method":"the silhouette's width row by row at a level of 235 of 255; a station is the row where the width changes, (1050.4 - row) / 610.4 x 1.16 from the rear face (± 4 px, 0.008 in); widths as read over 548 px/in (± 3 px, 0.006 in)","via":"harvest"},"note":"Row 747."}],"note":"The manual: \"Note that the XRF muzzle device has a very steep taper angle which results in a rock-solid lock up with very low torque.\" (p. 6). On the photo it narrows from 404 to 364 px over 87 rows: about 13 degrees a side."},"taper_end_x":{"label":"The taper ends at the ported body (from the rear face)","kind":"length","measurements":[{"id":"photo","value":0.742,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/dead-air-xrf-brake 8425e22cd635 (Midwest Gun Works, RXD674 standing on its rear face, seen square from its side and 13 degrees from above, 1500 x 1500, on white)","scaleRef":"its published length, 1.16 in, over the axis from the front face's middle to the rear face's (627 px with the 13 degrees taken out: 540.5 px/in along); its published diameter, 0.81 in, over the hex's 444 px (548 px/in across)","method":"the silhouette's width row by row at a level of 235 of 255; a station is the row where the width changes, (1050.4 - row) / 610.4 x 1.16 from the rear face (± 4 px, 0.008 in); widths as read over 548 px/in (± 3 px, 0.006 in)","via":"harvest"},"note":"Row 660."}]},"taper_front_d":{"label":"The taper's small end","kind":"length","measurements":[{"id":"photo","value":0.664,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/dead-air-xrf-brake 8425e22cd635 (Midwest Gun Works, RXD674 standing on its rear face, seen square from its side and 13 degrees from above, 1500 x 1500, on white)","scaleRef":"its published length, 1.16 in, over the axis from the front face's middle to the rear face's (627 px with the 13 degrees taken out: 540.5 px/in along); its published diameter, 0.81 in, over the hex's 444 px (548 px/in across)","method":"the silhouette's width row by row at a level of 235 of 255; a station is the row where the width changes, (1050.4 - row) / 610.4 x 1.16 from the rear face (± 4 px, 0.008 in); widths as read over 548 px/in (± 3 px, 0.006 in)","via":"harvest"},"note":"364 px at row 660."}]},"body_d":{"label":"The ported body ahead of the taper","kind":"length","measurements":[{"id":"photo","value":0.653,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/dead-air-xrf-brake 8425e22cd635 (Midwest Gun Works, RXD674 standing on its rear face, seen square from its side and 13 degrees from above, 1500 x 1500, on white)","scaleRef":"its published length, 1.16 in, over the axis from the front face's middle to the rear face's (627 px with the 13 degrees taken out: 540.5 px/in along); its published diameter, 0.81 in, over the hex's 444 px (548 px/in across)","method":"the silhouette's width row by row at a level of 235 of 255; a station is the row where the width changes, (1050.4 - row) / 610.4 x 1.16 from the rear face (± 4 px, 0.008 in); widths as read over 548 px/in (± 3 px, 0.006 in)","via":"harvest"},"note":"356 to 360 px, rows 440 to 657."}]},"front_round":{"label":"The front face's outer edge, rounded","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the photo is taken from above, and the front face's far rim and the edge's round are one curve in its silhouette (rows 399 to 440).","via":"harvest"}}]},"bore_d":{"label":"The hole through the front face","kind":"length","measurements":[{"id":"photo","value":0.26,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/dead-air-xrf-brake 8425e22cd635 (Midwest Gun Works, RXD674 standing on its rear face, seen square from its side and 13 degrees from above, 1500 x 1500, on white)","scaleRef":"its published length, 1.16 in, over the axis from the front face's middle to the rear face's (627 px with the 13 degrees taken out: 540.5 px/in along); its published diameter, 0.81 in, over the hex's 444 px (548 px/in across)","method":"the silhouette's width row by row at a level of 235 of 255; a station is the row where the width changes, (1050.4 - row) / 610.4 x 1.16 from the rear face (± 4 px, 0.008 in); widths as read over 548 px/in (± 3 px, 0.006 in)","via":"harvest"},"note":"The dark of the hole across the face's middle row (440), columns 678 to 835: 0.26 to 0.29 in, which may take in a chamfer; Dead Air: \"Bore .22\"."}]},"port_x":{"label":"The port's middle, from the rear face","kind":"length","measurements":[{"id":"photo","value":0.922,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/dead-air-xrf-brake 8425e22cd635 (Midwest Gun Works, RXD674 standing on its rear face, seen square from its side and 13 degrees from above, 1500 x 1500, on white)","scaleRef":"its published length, 1.16 in, over the axis from the front face's middle to the rear face's (627 px with the 13 degrees taken out: 540.5 px/in along); its published diameter, 0.81 in, over the hex's 444 px (548 px/in across)","method":"the silhouette's width row by row at a level of 235 of 255; a station is the row where the width changes, (1050.4 - row) / 610.4 x 1.16 from the rear face (± 4 px, 0.008 in); widths as read over 548 px/in (± 3 px, 0.006 in)","via":"harvest"},"note":"Its near mouth's rim from row 495 to 635."}],"note":"Dead Air: \"the performance of a single-port brake design\". One slot through the body: the backdrop shows straight through it (column 820 is white from row 505 to 610), so its two mouths are opposite each other. Turned 23 degrees from the lens on this photo; the oblique on Dead Air's page (222c079d4c69) shows one mouth and the light through it."},"port_length":{"label":"The port's length along the axis","kind":"length","measurements":[{"id":"photo","value":0.266,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/dead-air-xrf-brake 8425e22cd635 (Midwest Gun Works, RXD674 standing on its rear face, seen square from its side and 13 degrees from above, 1500 x 1500, on white)","scaleRef":"its published length, 1.16 in, over the axis from the front face's middle to the rear face's (627 px with the 13 degrees taken out: 540.5 px/in along); its published diameter, 0.81 in, over the hex's 444 px (548 px/in across)","method":"the silhouette's width row by row at a level of 235 of 255; a station is the row where the width changes, (1050.4 - row) / 610.4 x 1.16 from the rear face (± 4 px, 0.008 in); widths as read over 548 px/in (± 3 px, 0.006 in)","via":"harvest"},"note":"Its near mouth, rows 495 to 635: a slot with round ends."}]},"port_width":{"label":"The port's width across","kind":"length","measurements":[{"id":"photo","value":0.178,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/dead-air-xrf-brake 8425e22cd635 (Midwest Gun Works, RXD674 standing on its rear face, seen square from its side and 13 degrees from above, 1500 x 1500, on white)","scaleRef":"its published length, 1.16 in, over the axis from the front face's middle to the rear face's (627 px with the 13 degrees taken out: 540.5 px/in along); its published diameter, 0.81 in, over the hex's 444 px (548 px/in across)","method":"the silhouette's width row by row at a level of 235 of 255; a station is the row where the width changes, (1050.4 - row) / 610.4 x 1.16 from the rear face (± 4 px, 0.008 in); widths as read over 548 px/in (± 3 px, 0.006 in)","via":"harvest"},"note":"90 px across its near mouth at 23 degrees from the lens (its middle 69 px off the body's of 179 px half width): 98 px square on."}]},"chamber_front_wall":{"label":"The front wall, how thick the nose is ahead of the room inside it","kind":"length","measurements":[{"id":"assumed","value":0.08,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the inside is a room at the barrel thread's size from the rear face to a front wall about as thick as the nose's side wall (body_d less the room, halved: 0.08 in).","via":"harvest"}}],"note":"Not stated, and no view on file looks into the device. Dead Air: the brake \"helps capture lead and debris before it enters the suppressor\"; on Midwest Gun Works' photo the backdrop shows straight through the port (8425e22cd635), and the hole in the front face is the bore's size. With the barrel's socket drawn as a room carried on at its size to this wall, the model's 17-4 weighs the published 1.05 oz within a few percent; drawn solid ahead of the barrel's thread it was 36% over."},"barrel_thread_major_d":{"label":"The barrel thread's crests (1/2-28), the socket it goes in, and the room inside","kind":"length","measurements":[{"id":"tdp","value":0.4957,"unit":"in","pm":0.0033,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.thread_major_d}","via":"harvest"},"note":"A 1/2-28 thread's crests, as read from the Army barrel's drawing for BCM's barrel; the device's own thread isn't dimensioned."}]}}},{"subject":"eotech-exps3","title":"EOTECH HWS EXPS3 holographic weapon sight (EXPS3-0, black, 1-Dot Speed Ring; EXPS3-0TAN the same sight in tan)","dimensions":{"length":{"label":"Overall length (the battery compartment's front to the rear cover's screws)","kind":"length","measurements":[{"id":"manual","value":3.8,"unit":"in","stated":"L × W × H 3.8\" × 2.3\" × 2.9\" (96.5 × 58.4 × 73.7mm)","source":{"type":"spec","publisher":"manufacturer","name":"EOTECH, EXPS3 HWS user manual XE1974 Rev C (January 2022), p. 9 Specifications, the PDF on EOTECH's own shop","url":"https://cdn.shopify.com/s/files/1/0698/3044/3191/files/EOTECH_HWS_Manual_EXPS3_XE1974_RevC.pdf","retrieved":"2026-10-06","via":"harvest"}},{"id":"catalog","value":3.8,"unit":"in","stated":"L × W × H 3.8” × 2.3” × 2.9” / 96.5 × 58.4 × 73.7mm","source":{"type":"spec","publisher":"manufacturer","name":"EOTECH, product catalog (2026), p. 12 EXPS3","url":"https://cdn.shopify.com/s/files/1/0698/3044/3191/files/EOTECH_Full_Catalog.pdf?v=1768427848","retrieved":"2026-10-06","via":"harvest"}},{"id":"trex","value":3.8,"unit":"in","stated":"Dimensions 3.8\" x 2.3\" x 2.9\" (96.5 x 58.4 x 73.7 mm)","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, EOTECH HWS EXPS3 Series, technical specifications","url":"https://www.trex-arms.com/store/eotech-exps3-0/","retrieved":"2026-10-06","via":"harvest"}},{"id":"tnvc","value":3.5,"unit":"in","stated":"Dimensions 3.5in(L) x 2.4in(W) x 2.8in(H)","source":{"type":"spec","publisher":"retailer","name":"Tactical Night Vision Company, EOTECH EXPS-3, specifications (an older set of figures)","url":"https://tnvc.com/shop/eotech-exps-3/","retrieved":"2026-10-06","via":"harvest"},"note":"The figures of the sight's first years (the 2010 review has 3.5 x 2.4 x 2.4): not the manual's of 2022."}],"adopt":{"from":"manual","reason":"EOTECH's own manual (2022) and catalog (2026) agree, and three straight side views have the manual's ratio of length to height (1.29 to 1.30 against 1.31); the 3.5 in on sellers' older pages is an earlier sheet's and stays a visible conflict."},"note":"The straight side views' x-extent: the battery compartment's rounded front to the heads of the lower screws of the rear cover."},"width":{"label":"Overall width (the hood's left flank to the battery cap's face)","kind":"length","measurements":[{"id":"manual","value":2.3,"unit":"in","stated":"L × W × H 3.8\" × 2.3\" × 2.9\" (96.5 × 58.4 × 73.7mm)","source":{"type":"spec","publisher":"manufacturer","name":"EOTECH, EXPS3 HWS user manual XE1974 Rev C (January 2022), p. 9 Specifications, the PDF on EOTECH's own shop","url":"https://cdn.shopify.com/s/files/1/0698/3044/3191/files/EOTECH_HWS_Manual_EXPS3_XE1974_RevC.pdf","retrieved":"2026-10-06","via":"harvest"}},{"id":"catalog","value":2.3,"unit":"in","stated":"L × W × H 3.8” × 2.3” × 2.9” / 96.5 × 58.4 × 73.7mm","source":{"type":"spec","publisher":"manufacturer","name":"EOTECH, product catalog (2026), p. 12 EXPS3","url":"https://cdn.shopify.com/s/files/1/0698/3044/3191/files/EOTECH_Full_Catalog.pdf?v=1768427848","retrieved":"2026-10-06","via":"harvest"}},{"id":"patan","value":2.3,"unit":"in","stated":"Length: 3.8” Width: 2.3” Height: 2.9”","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, EOTech EXPS3-0 holographic sight, tan (EXPS3-0TAN), description","url":"https://www.primaryarms.com/eotech-exps3-0-holographic-weapon-sight-tan","retrieved":"2026-10-06","via":"harvest"}},{"id":"tnvc","value":2.4,"unit":"in","stated":"Dimensions 3.5in(L) x 2.4in(W) x 2.8in(H)","source":{"type":"spec","publisher":"retailer","name":"Tactical Night Vision Company, EOTECH EXPS-3, specifications (an older set of figures)","url":"https://tnvc.com/shop/eotech-exps-3/","retrieved":"2026-10-06","via":"harvest"},"note":"The older set of figures."}],"adopt":{"from":"manual","reason":"EOTECH's own manual and catalog agree; the older set on TNVC's page stays a visible conflict."},"note":"EOTECH doesn't say what it spans. Its view from above, scaled by the published length, is 2.28 in from the hood's left flank to the battery cap's knurled face on the right, and 2.23 in across the hood alone (hood_width)."},"height":{"label":"Overall height (the clamp's bottom to the hood's top)","kind":"length","measurements":[{"id":"manual","value":2.9,"unit":"in","stated":"L × W × H 3.8\" × 2.3\" × 2.9\" (96.5 × 58.4 × 73.7mm)","source":{"type":"spec","publisher":"manufacturer","name":"EOTECH, EXPS3 HWS user manual XE1974 Rev C (January 2022), p. 9 Specifications, the PDF on EOTECH's own shop","url":"https://cdn.shopify.com/s/files/1/0698/3044/3191/files/EOTECH_HWS_Manual_EXPS3_XE1974_RevC.pdf","retrieved":"2026-10-06","via":"harvest"}},{"id":"catalog","value":2.9,"unit":"in","stated":"L × W × H 3.8” × 2.3” × 2.9” / 96.5 × 58.4 × 73.7mm","source":{"type":"spec","publisher":"manufacturer","name":"EOTECH, product catalog (2026), p. 12 EXPS3","url":"https://cdn.shopify.com/s/files/1/0698/3044/3191/files/EOTECH_Full_Catalog.pdf?v=1768427848","retrieved":"2026-10-06","via":"harvest"}},{"id":"trex","value":2.9,"unit":"in","stated":"Dimensions 3.8\" x 2.3\" x 2.9\" (96.5 x 58.4 x 73.7 mm)","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, EOTECH HWS EXPS3 Series, technical specifications","url":"https://www.trex-arms.com/store/eotech-exps3-0/","retrieved":"2026-10-06","via":"harvest"}},{"id":"tnvc","value":2.8,"unit":"in","stated":"Dimensions 3.5in(L) x 2.4in(W) x 2.8in(H)","source":{"type":"spec","publisher":"retailer","name":"Tactical Night Vision Company, EOTECH EXPS-3, specifications (an older set of figures)","url":"https://tnvc.com/shop/eotech-exps-3/","retrieved":"2026-10-06","via":"harvest"},"note":"The older set of figures."}],"adopt":{"from":"manual","reason":"EOTECH's own manual and catalog agree; the older set on TNVC's page stays a visible conflict."},"note":"From the bottom of the base's jaws, not the rail's top: the straight side views' y-extent between those two is 2.94 in at the published length's scale."},"weight":{"label":"Weight (with its base; EOTECH doesn't say whether with the battery)","kind":"mass","measurements":[{"id":"manual","value":11.2,"unit":"oz","stated":"Weight 11.2 oz (317.5g)","source":{"type":"spec","publisher":"manufacturer","name":"EOTECH, EXPS3 HWS user manual XE1974 Rev C (January 2022), p. 9 Specifications, the PDF on EOTECH's own shop","url":"https://cdn.shopify.com/s/files/1/0698/3044/3191/files/EOTECH_HWS_Manual_EXPS3_XE1974_RevC.pdf","retrieved":"2026-10-06","via":"harvest"}},{"id":"catalog","value":11.2,"unit":"oz","stated":"WEIGHT 11.2oz / 317.5g","source":{"type":"spec","publisher":"manufacturer","name":"EOTECH, product catalog (2026), p. 12 EXPS3","url":"https://cdn.shopify.com/s/files/1/0698/3044/3191/files/EOTECH_Full_Catalog.pdf?v=1768427848","retrieved":"2026-10-06","via":"harvest"}},{"id":"trex","value":11.2,"unit":"oz","stated":"Weight 11.2 oz (317.5 g)","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, EOTECH HWS EXPS3 Series, technical specifications","url":"https://www.trex-arms.com/store/eotech-exps3-0/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"manual","reason":"EOTECH's own manual; its catalog and the sellers repeat it."}},"window_width":{"label":"Window's width","kind":"length","measurements":[{"id":"manual","value":1.2,"unit":"in","pm":0.005,"stated":"Window Dimensions 1.20\" × 0.85\" (30 × 23mm)","source":{"type":"spec","publisher":"manufacturer","name":"EOTECH, EXPS3 HWS user manual XE1974 Rev C (January 2022), p. 9 Specifications, the PDF on EOTECH's own shop","url":"https://cdn.shopify.com/s/files/1/0698/3044/3191/files/EOTECH_HWS_Manual_EXPS3_XE1974_RevC.pdf","retrieved":"2026-10-06","via":"harvest"}},{"id":"tnvc","value":1.2,"unit":"in","pm":0.005,"stated":"Window Dimensions 1.20in x 0.85in","source":{"type":"spec","publisher":"retailer","name":"Tactical Night Vision Company, EOTECH EXPS-3, specifications (an older set of figures)","url":"https://tnvc.com/shop/eotech-exps-3/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"manual","reason":"EOTECH's own manual; the seller repeats it."}},"window_height":{"label":"Window's height","kind":"length","measurements":[{"id":"manual","value":0.85,"unit":"in","stated":"Window Dimensions 1.20\" × 0.85\" (30 × 23mm)","source":{"type":"spec","publisher":"manufacturer","name":"EOTECH, EXPS3 HWS user manual XE1974 Rev C (January 2022), p. 9 Specifications, the PDF on EOTECH's own shop","url":"https://cdn.shopify.com/s/files/1/0698/3044/3191/files/EOTECH_HWS_Manual_EXPS3_XE1974_RevC.pdf","retrieved":"2026-10-06","via":"harvest"}},{"id":"tnvc","value":0.85,"unit":"in","stated":"Window Dimensions 1.20in x 0.85in","source":{"type":"spec","publisher":"retailer","name":"Tactical Night Vision Company, EOTECH EXPS-3, specifications (an older set of figures)","url":"https://tnvc.com/shop/eotech-exps-3/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"manual","reason":"EOTECH's own manual; the seller repeats it."}},"front_window_thickness":{"label":"Front window's glass, thickness","kind":"length","measurements":[{"id":"manual","value":3.17,"unit":"mm","stated":"Front Window Material Glass 1/8\" (3.17mm) thick","source":{"type":"spec","publisher":"manufacturer","name":"EOTECH, EXPS3 HWS user manual XE1974 Rev C (January 2022), p. 9 Specifications, the PDF on EOTECH's own shop","url":"https://cdn.shopify.com/s/files/1/0698/3044/3191/files/EOTECH_HWS_Manual_EXPS3_XE1974_RevC.pdf","retrieved":"2026-10-06","via":"harvest"}}]},"rear_window_thickness":{"label":"Rear window's laminate, thickness","kind":"length","measurements":[{"id":"manual","value":4.76,"unit":"mm","stated":"Rear Window Material Laminate 3/16\" (4.76mm) thick","source":{"type":"spec","publisher":"manufacturer","name":"EOTECH, EXPS3 HWS user manual XE1974 Rev C (January 2022), p. 9 Specifications, the PDF on EOTECH's own shop","url":"https://cdn.shopify.com/s/files/1/0698/3044/3191/files/EOTECH_HWS_Manual_EXPS3_XE1974_RevC.pdf","retrieved":"2026-10-06","via":"harvest"}}]},"base_raise":{"label":"The base's raise over EOTECH's earlier base (not a height over the rail)","kind":"length","measurements":[{"id":"catalog","value":7,"unit":"mm","stated":"Equipped with a 7mm raised quick-detach base for lower 1/3 iron sight co-witness","source":{"type":"spec","publisher":"manufacturer","name":"EOTECH, product catalog (2026), p. 12 EXPS3","url":"https://cdn.shopify.com/s/files/1/0698/3044/3191/files/EOTECH_Full_Catalog.pdf?v=1768427848","retrieved":"2026-10-06","via":"harvest"}},{"id":"tnvc","value":7,"unit":"mm","stated":"An integral quick-detach rail mount raises the sight by 7mm, providing the operator with a “lower 1/3 co-witness” sight height","source":{"type":"spec","publisher":"retailer","name":"Tactical Night Vision Company, EOTECH EXPS-3, specifications (an older set of figures)","url":"https://tnvc.com/shop/eotech-exps-3/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"catalog","reason":"EOTECH's own catalog; the seller says the same."},"note":"What EOTECH says of the sight's height, and all it says: the base is 7 mm higher than its other sights', for a lower 1/3 co-witness. It is not measured from the rail and nothing is drawn from it."},"hood_width":{"label":"Hood's width across its two flanks","kind":"length","measurements":[{"id":"top-photo","value":2.262,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/eotech-exps3 48bb645b068b (EOTECH exps3_to: the black sight from above, 700 x 700 with its own alpha, the muzzle to the right)","scaleRef":"the published length, 3.8 in = 528 px (138.9 px/in), and width, 2.3 in = 317 px (137.8 px/in), which agree within 0.8%: 138.4 px/in","method":"the hood across its two flanks, seen from above: the outline's extent across the sight where the hood is, 0.3 to 2.6 in ahead of the rear cover's screws (tools/trace.py, `height` in that range): rows 195 to 508","via":"harvest"}}],"note":"The hood is the widest thing but the battery cap: the published width less the cap's stand past the right flank. The view from behind has it 960 px wide, which at the published height's scale (428.3 px/in) is 2.24 in: the two agree within 0.9%, and the view from behind is scaled by both."},"hood_thickness":{"label":"Hood's thickness (its top, seen from behind)","kind":"length","measurements":[{"id":"rear-photo","value":0.103,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/eotech-exps3 4bbcf783f58b (Primary Arms EXPS3-0_03: the black sight from behind, straight on, on white, 2200 x 1466)","scaleRef":"the published height, 2.9 in = 1242 px (428.3 px/in), and the hood's width from the view above, 2.262 in = 960 px (424.4 px/in), which agree within 0.9%: 426.4 px/in","method":"the hood's top edge-on on the window's middle columns: dark from row 104.5 to row 148.5, the backdrop of the gap under it from 149: 44 px. Its rear edge is rounded and it is seen a little from below: it reads thick if anything","via":"harvest"}}]},"cap_knurl_teeth":{"label":"Battery cap, the teeth of its knurl","kind":"count","measurements":[{"id":"right-photo","value":41,"unit":"count","pm":1,"source":{"type":"photo","photo":"references/eotech-exps3 41e27975b533 (Primary Arms EXPS3-0TAN_01: the tan sight's right side straight on, on white, 2200 x 1467, the muzzle to the right)","scaleRef":"none: a count","method":"the cap's rim unwrapped about its centre ((1753, 933) after a fit of the rim's radius took out the first guess's offset; references/eotech-exps3/picks/cap_unwrap.png), the teeth counted as the rim's crossings of its own running mean: 12 over 5 to 112 degrees and 16 over 130 to 250 (8.5 to 9.0 degrees apart), 43 crossings over the whole turn of which the lanyard and its crimps split three and hide one: 41, give or take one","via":"harvest"}}]},"cap_knurl_depth":{"label":"Battery cap, the depth of its knurl's teeth","kind":"length","measurements":[{"id":"right-photo","value":0.02,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/eotech-exps3 41e27975b533 (Primary Arms EXPS3-0TAN_01: the tan sight's right side straight on, on white, 2200 x 1467, the muzzle to the right)","scaleRef":"the published length, 3.8 in = 1486 px (391.1 px/in), and height, 2.9 in = 1143 px (394.1 px/in), which agree within 0.8%: 392.6 px/in","method":"the unwrapped rim's radius from the teeth's roots to their tips: 163 to 172 px over the turn (its 10th and 90th percentiles), 8 px once the centre's residual is allowed for","via":"harvest"}}]},"top_above_rail":{"label":"Hood's top above the rail's top","kind":"length","measurements":[{"id":"maker-rear","value":2.65,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/eotech-exps3 220d3ed767ac (EOTECH exps3_tanbr: the tan sight from behind, 700 x 700 with its own alpha)","scaleRef":"its own window, clear from edge to edge in this view: 166 px wide for the published 1.20 in (138.3 px/in) and 116.5 px high for the published 0.85 in (137.1 px/in), with the published height over the outline's 405 px (139.5 px/in; its lowest rows may be the ground's shadow): 138.5 px/in, to 1.5%","method":"on the window's middle columns: the hood's top edge at row 151.5, the roof of the notch in the rear cover (the cover's lower edge between the two jaws) at row 518.5: 367 px. A pixel is 0.007 in; ± covers the scale and both edges","via":"harvest"}},{"id":"rear-photo","value":2.578,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/eotech-exps3 4bbcf783f58b (Primary Arms EXPS3-0_03: the black sight from behind, straight on, on white, 2200 x 1466)","scaleRef":"the published height, 2.9 in = 1242 px (428.3 px/in), and the hood's width from the view above, 2.262 in = 960 px (424.4 px/in), which agree within 0.9%: 426.4 px/in","method":"on the window's middle columns (1100, 1150): the hood's top edge at row 104.5, the notch's roof in the older rear cover at row 1203.5 (1207 to 1208 at columns 1000, 1050 and 1200, where the roof's corners round): 1099 px","via":"harvest"},"note":"The older cover's notch: the least the height can be, not where the rail is."},{"id":"bolt","value":2.68,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/eotech-exps3 41e27975b533 (Primary Arms EXPS3-0TAN_01: the tan sight's right side straight on, on white, 2200 x 1467, the muzzle to the right)","scaleRef":"the published length, 3.8 in = 1486 px (391.1 px/in), and height, 2.9 in = 1143 px (394.1 px/in), which agree within 0.8%: 392.6 px/in","method":"the hood's top (row 186) to the centre of the adjustment nut on the cross bolt's end (rows 1173 to 1303: 1238): 1052 px. The bolt's axis, not the rail's top: ± is the slot's depth less a bolt's radius either way","via":"harvest"}}],"adopt":{"from":"maker-rear","reason":"The lower of the two covers' notches (the rail is under both), and within a slot's depth of the cross bolt's axis; the older cover's notch stands 0.07 in clear of the rail."},"note":"No view on file has the sight on a rail. The rail lies in the notch in the rear cover's lower edge, so its top is no higher than the notch's roof: on the older cover in Primary Arms' photo (the one marked L3) that roof is 2.578 in below the hood's top, on the current cover in EOTECH's own picture 2.65 in, and the rail is under both. The cross bolt, which lies in a rail slot (the manual, p. 13), has its axis 2.68 in below the hood's top in the right side view: a bolt in a groove 0.118 in deep has its axis within that of the rail's top. A buyer's photo of the sight from the front (The Reptile House Blog, references/eotech-exps3 1a6701225c95) shows the base's own channel with the nut's centre level with its roof, within 0.04 in. And at 2.65 the base's jaws reach 0.26 in below the rail's top (the catalog's other clamps: 0.22 to 0.25), where at 2.578 they would reach 0.33 and the bolt would lie wholly under the slot's floor."},"clamp_below_rail":{"label":"Lowest point (the quick-detach lever's underside) below the rail's top","kind":"length","measurements":[{"id":"derived","value":0.25,"unit":"in","pm":0.07,"source":{"type":"derived","expr":"{.height} - {.top_above_rail}","via":"harvest"},"note":"The lever's latch hangs lowest, on the left; the jaws themselves end a few hundredths higher."}],"note":"The published height is from the lowest point to the hood's top (the side views' and the view from behind's whole extent)."},"window_centre_below_top":{"label":"Window's centre below the hood's top","kind":"length","measurements":[{"id":"rear-photo","value":0.791,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/eotech-exps3 4bbcf783f58b (Primary Arms EXPS3-0_03: the black sight from behind, straight on, on white, 2200 x 1466)","scaleRef":"the published height, 2.9 in = 1242 px (428.3 px/in), and the hood's width from the view above, 2.262 in = 960 px (424.4 px/in), which agree within 0.9%: 426.4 px/in","method":"on the window's middle columns: the hood's top edge at row 104.5; the window between the black of its frame's lips, rows 232 to 645 (centre 438.5), and its clear part, rows 288 to 602 (centre 445): the centre taken at row 442, 337.5 px down. This photo is taken from near enough that the opening's upper and lower walls show as black bands; ± covers which band is wall and which lip","via":"harvest"}},{"id":"maker-rear","value":0.792,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/eotech-exps3 220d3ed767ac (EOTECH exps3_tanbr: the tan sight from behind, 700 x 700 with its own alpha)","scaleRef":"its own window, clear from edge to edge in this view: 166 px wide for the published 1.20 in (138.3 px/in) and 116.5 px high for the published 0.85 in (137.1 px/in), with the published height over the outline's 405 px (139.5 px/in; its lowest rows may be the ground's shadow): 138.5 px/in, to 1.5%","method":"the hood's top edge at row 151.5, the window's clear opening rows 203 to 319.5 (centre 261.25): 109.75 px","via":"harvest"}}],"adopt":{"from":"rear-photo","reason":"Three times the resolution; EOTECH's own picture of the tan sight, in which the whole window is clear, reads the same."}},"hood_left_reach":{"label":"Hood's left flank from the rail's centre plane","kind":"length","measurements":[{"id":"rear-photo","value":1.173,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/eotech-exps3 4bbcf783f58b (Primary Arms EXPS3-0_03: the black sight from behind, straight on, on white, 2200 x 1466)","scaleRef":"the published height, 2.9 in = 1242 px (428.3 px/in), and the hood's width from the view above, 2.262 in = 960 px (424.4 px/in), which agree within 0.9%: 426.4 px/in","method":"the outline's left extreme (column 614, the hood's left flank at its skirt) to the rail's centre taken at column 1114: 500 px. ± covers the centre's reading (8 px) and the scale","via":"harvest"}},{"id":"top-photo","value":1.185,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/eotech-exps3 48bb645b068b (EOTECH exps3_to: the black sight from above, 700 x 700 with its own alpha, the muzzle to the right)","scaleRef":"the published length, 3.8 in = 528 px (138.9 px/in), and width, 2.3 in = 317 px (137.8 px/in), which agree within 0.8%: 138.4 px/in","method":"the hood's left flank (row 195) to the middle of the rear cover's two screw heads (rows 278 and 440: 359): 164 px","via":"harvest"}}],"adopt":{"from":"rear-photo","reason":"The view the rail's channel is seen in, at three times the resolution; the view from above agrees within 0.012 in."},"note":"The rail's centre is taken midway between the rear cover's two lower screws (columns 860 and 1365 in the view from behind: 1112.5) and the notch's roof (992 to 1253 at row 1210: 1122.5); the window's middle is column 1106. The hood isn't centred on the rail: its right flank is 1.07 in from it (457 px)."},"hood_left_z":{"label":"Hood's left flank in the frame (z, the rail's centre is 0)","kind":"length","measurements":[{"id":"derived","value":-1.173,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"-{.hood_left_reach}","via":"harvest"},"note":"Where the view from above and the view from behind have their left edge."}]},"rear_behind_bolt":{"label":"Rear cover's screw heads (the sight's rear end) behind the cross bolt","kind":"length","measurements":[{"id":"right-photo","value":1.938,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/eotech-exps3 41e27975b533 (Primary Arms EXPS3-0TAN_01: the tan sight's right side straight on, on white, 2200 x 1467, the muzzle to the right)","scaleRef":"the published length, 3.8 in = 1486 px (391.1 px/in), and height, 2.9 in = 1143 px (394.1 px/in), which agree within 0.8%: 392.6 px/in","method":"the adjustment nut on the cross bolt's right end, a circle whose box is columns 1170 to 1300 (centre 1235), from the outline's rear extreme (column 475): 760 px. ± covers the nut's centre (5 px) and the scale","via":"harvest"}},{"id":"left-photo","value":1.954,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/eotech-exps3 29f6391862ba (Primary Arms EXPS3-0_05: the black sight's left side straight on, on white, 2200 x 1467, the muzzle to the left)","scaleRef":"the published length, 3.8 in = 1579 px (415.5 px/in), and height, 2.9 in = 1221 px (421.0 px/in), which agree within 1.3%: 418.3 px/in","method":"the quick-detach lever's cam, on the bolt's other end, columns 960 to 1110 (centre 1035), from the outline's rear extreme (column 1852): 817 px. The cam isn't round: its middle is only near the bolt's axis","via":"harvest"}}],"adopt":{"from":"right-photo","reason":"The nut is on the bolt itself and is round; the cam on the left end agrees within 0.016 in."}},"side_rear_x":{"label":"The sight's rear end in the frame (x, the cross bolt is 0)","kind":"length","measurements":[{"id":"derived","value":-1.938,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"-{.rear_behind_bolt}","via":"harvest"},"note":"Where the side views and the view from above have their rear edge."}]},"clamp_rear":{"label":"Base's reach behind the cross bolt (to the rear foot's rear end)","kind":"length","measurements":[{"id":"right-photo","value":1.77,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/eotech-exps3 41e27975b533 (Primary Arms EXPS3-0TAN_01: the tan sight's right side straight on, on white, 2200 x 1467, the muzzle to the right)","scaleRef":"the published length, 3.8 in = 1486 px (391.1 px/in), and height, 2.9 in = 1143 px (394.1 px/in), which agree within 0.8%: 392.6 px/in","method":"the nut's centre (column 1235) back to the rear end of the base's rear foot (column 540): 695 px","via":"harvest"}},{"id":"left-photo","value":1.788,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/eotech-exps3 29f6391862ba (Primary Arms EXPS3-0_05: the black sight's left side straight on, on white, 2200 x 1467, the muzzle to the left)","scaleRef":"the published length, 3.8 in = 1579 px (415.5 px/in), and height, 2.9 in = 1221 px (421.0 px/in), which agree within 1.3%: 418.3 px/in","method":"the cam's middle (column 1035) to the base's rear end (column 1790, under the rear cover's screws): 748 px less the 0.016 in the cam's middle reads behind the nut","via":"harvest"}}],"adopt":{"from":"right-photo","reason":"Measured from the nut itself; the left view agrees within 0.02 in."}},"clamp_front":{"label":"Base's reach ahead of the cross bolt (to the clamp block's front end)","kind":"length","measurements":[{"id":"right-photo","value":0.93,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/eotech-exps3 41e27975b533 (Primary Arms EXPS3-0TAN_01: the tan sight's right side straight on, on white, 2200 x 1467, the muzzle to the right)","scaleRef":"the published length, 3.8 in = 1486 px (391.1 px/in), and height, 2.9 in = 1143 px (394.1 px/in), which agree within 0.8%: 392.6 px/in","method":"the nut's centre (column 1235) forward to the clamp block's front end (column 1600): 365 px","via":"harvest"}},{"id":"left-photo","value":0.913,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/eotech-exps3 29f6391862ba (Primary Arms EXPS3-0_05: the black sight's left side straight on, on white, 2200 x 1467, the muzzle to the left)","scaleRef":"the published length, 3.8 in = 1579 px (415.5 px/in), and height, 2.9 in = 1221 px (421.0 px/in), which agree within 1.3%: 418.3 px/in","method":"the base's front end (the lever's tip, column 661) to the cam's middle (column 1035): 374 px, plus the 0.016 in the cam's middle reads behind the nut","via":"harvest"}}],"adopt":{"from":"right-photo","reason":"Measured from the nut itself; the left view agrees within 0.02 in."}},"optical_axis_above_rail":{"label":"Window's centre above the rail's top (EOTECH states no height of the reticle)","kind":"length","measurements":[{"id":"derived","value":1.859,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{.top_above_rail} - {.window_centre_below_top}","via":"harvest"},"note":"The hood's top over the rail less the window's centre under the hood's top, which two photos read alike."}],"note":"No page or document on file states it: EOTECH says \"7mm raised quick-detach base for lower 1/3 iron sight co-witness\" and T.REX ARMS \"Optic Height Lower 1/3rd co-witness\". A hologram's reticle has no axis of its own in the window; the sight line is taken through the window's centre. It is as good as the rail's top is known under the sight (top_above_rail: no view on file has it on a rail): with the older cover's notch taken for the rail's top it would be 1.79 in. At 1.86 in an AR's own sights (1.4 in over the rail) come up at the window's lower edge, lower than \"lower 1/3\" suggests: a figure from EOTECH, or a straight view of the sight on a rail, would settle it. The 1.74 in a review gives is the EXPS3 HD's, another sight; a riser's 2.26 in isn't this sight's."},"mount_length":{"label":"Base's length along the rail (the rear foot's rear end to the clamp block's front end)","kind":"length","measurements":[{"id":"right-photo","value":2.7,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/eotech-exps3 41e27975b533 (Primary Arms EXPS3-0TAN_01: the tan sight's right side straight on, on white, 2200 x 1467, the muzzle to the right)","scaleRef":"the published length, 3.8 in = 1486 px (391.1 px/in), and height, 2.9 in = 1143 px (394.1 px/in), which agree within 0.8%: 392.6 px/in","method":"the base's rear foot's rear end (column 540) to the clamp block's front end (column 1600): 1060 px","via":"harvest"}},{"id":"left-photo","value":2.699,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/eotech-exps3 29f6391862ba (Primary Arms EXPS3-0_05: the black sight's left side straight on, on white, 2200 x 1467, the muzzle to the left)","scaleRef":"the published length, 3.8 in = 1579 px (415.5 px/in), and height, 2.9 in = 1221 px (421.0 px/in), which agree within 1.3%: 418.3 px/in","method":"the base's front end (column 661) to its rear end (column 1790): 1129 px","via":"harvest"}},{"id":"tnvc","value":2.75,"unit":"in","pm":0.05,"stated":"features a shortened base that only requires about 2.75″ of rail space","source":{"type":"spec","publisher":"retailer","name":"Tactical Night Vision Company, EOTECH EXPS-3, specifications (an older set of figures)","url":"https://tnvc.com/shop/eotech-exps-3/","retrieved":"2026-10-06","via":"harvest"},"note":"\"About\": ± 0.05 written for it."},{"id":"cor","value":2.75,"unit":"in","pm":0.05,"stated":"Shortened base only requires at most 2 3/4 inch of rail space compared to the 4 inch N battery sights","source":{"type":"spec","publisher":"review","name":"Combat Optics Reviews, Eotech EXPS3-0 (2010), the maker's figures of that year","url":"https://combatopticsreviews.com/eotech-exps3-0-holographic-weapon-sight/","retrieved":"2026-10-06","via":"harvest"},"note":"\"At most\", of the 2010 sight: ± 0.05 written for it."}],"adopt":{"from":"right-photo","reason":"Two straight side views, one of each flank, read 2.70 in; the two old sentences round it up as the rail it needs."},"note":"EOTECH's current pages state none. The two old sentences (the 2010 review's and TNVC's, both of the sight's first years) say how much rail it needs, which is what the two side views read."},"window_corner_r":{"label":"Window's corner radius","kind":"length","measurements":[{"id":"rear-photo","value":0.18,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/eotech-exps3 4bbcf783f58b (Primary Arms EXPS3-0_03: the black sight from behind, straight on, on white, 2200 x 1466)","scaleRef":"the published height, 2.9 in = 1242 px (428.3 px/in), and the hood's width from the view above, 2.262 in = 960 px (424.4 px/in), which agree within 0.9%: 426.4 px/in","method":"the opening's lower corners: its clear width is 914 to 1287 at row 598, 898 to 1311 at row 588 and 876 to 1337 at row 560 against 867 to 1345 at its middle and a lower edge at row 602: an arc of about 75 px","via":"harvest"}}]},"tube_od":{"label":"Main tube OD","kind":"length","measurements":[],"note":"A holographic sight has no tube: its window is a rectangle in a housing (window_width, window_height). Not applicable; kept as the checklist's entry."},"eye_relief":{"label":"Eye relief","kind":"length","measurements":[],"note":"EOTECH's manual, p. 9: \"Eye Relief Unlimited\". It has no eye point of its own and the part states no `eye`."}}},{"subject":"eotech-g33","title":"EOTECH G33 Magnifier on its Switch-to-Side (STS) mount, the 7 mm riser fitted","dimensions":{"length":{"label":"Overall length","kind":"length","measurements":[{"id":"page","value":102,"unit":"mm","stated":"4\" x 2.2\" x 3.3\" (102 x 55.9 x 73.7 mm)","source":{"type":"spec","publisher":"manufacturer","name":"eotechinc.com, G33 Magnifier (Tech Specs)","url":"https://www.eotechinc.com/products/eotech-magnifier-g33","retrieved":"2026-10-06","via":"harvest"}},{"id":"catalog","value":102,"unit":"mm","stated":"4” × 2.2” × 3.3” / 102 × 55.9 × 73.7mm","source":{"type":"spec","publisher":"manufacturer","name":"EOTECH full catalogue (PDF), p. 23","url":"https://cdn.shopify.com/s/files/1/0698/3044/3191/files/EOTECH_Full_Catalog.pdf?v=1768427848","retrieved":"2026-10-06","via":"harvest"}},{"id":"manual-2022","value":113,"unit":"mm","stated":"4.4\" × 2.2\" × 3.3\" (113 × 55.9 × 73.7mm)","source":{"type":"spec","publisher":"manufacturer","name":"EOTECH G-Series Magnifiers user manual, January 2022 (hosted by T.REX ARMS), p. 6","url":"https://img.trex-arms.com/wp/uploads/2026/03/eotech-g-series-magnifier-user-manual-2022-01.pdf","retrieved":"2026-10-06","via":"harvest"}},{"id":"trex","value":113,"unit":"mm","stated":"4.4\" x 2.2\" x 3.3\" (113 x 55.9 x 73.7 mm)","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, EOTECH G33 3x Magnifier","url":"https://www.trex-arms.com/store/eotech-g33-3x-magnifier-73466","retrieved":"2026-10-06","via":"harvest"}},{"id":"arisaka","value":113,"unit":"mm","stated":"L x W x H = 4.4\" x 2.2\" x 3.3\" (113 x 55.9 x 73.7 mm)","source":{"type":"spec","publisher":"retailer","name":"Arisaka Defense, EOTech G33 Magnifier with STS Mount","url":"https://arisakadefense.com/eotech-g33-magnifier-with-sts-mount/","retrieved":"2026-10-06","via":"harvest"}},{"id":"manual-2015","value":99,"unit":"mm","stated":"Length: 3.9” (99mm)","source":{"type":"spec","publisher":"manufacturer","name":"L-3 EOTech, User's Manual for G33, Rev E, 2015 (hosted by Brownells)","url":"https://www.brownells.com/globalassets/pdfs/product-pdfs/eotech_g33_magnifier_product_manual.pdf","retrieved":"2026-10-06","via":"harvest"},"note":"The magnifier's row of the older sheet (the mount has its own row)."}],"adopt":{"from":"page","reason":"The maker's current page and catalogue, and the one figure the maker's own side views bear out: with the mount's published 1.66 in in the same picture, 4 in gives one scale within 0.1% on the left side and 0.3% on the right. The 2022 manual's 4.4 in (which T.REX and Arisaka repeat) would make the mount 1.83 in, and the 2015 sheet's 3.9 in is 2.5% short of it."},"note":"Three figures are published. On EOTECH's two side views the overall length and the STS mount's own length (sts_mount_length, 1.66 in, the 2015 manual) are 1654 and 687 px on the left side and 1116 and 462 px on the right: at 4 in the mount comes to 1.661 and 1.656 in; at 4.4 in it would be 1.83, at 3.9 in 1.62. What the 2022 manual's 4.4 in spans isn't said (nothing in the side views is that long: the mount's lever ends 2.2 in behind the front)."},"width":{"label":"Overall width (the mount's lever on the left to the horizontal adjustment's knob on the right)","kind":"length","measurements":[{"id":"page","value":55.9,"unit":"mm","stated":"4\" x 2.2\" x 3.3\" (102 x 55.9 x 73.7 mm)","source":{"type":"spec","publisher":"manufacturer","name":"eotechinc.com, G33 Magnifier (Tech Specs)","url":"https://www.eotechinc.com/products/eotech-magnifier-g33","retrieved":"2026-10-06","via":"harvest"}},{"id":"manual-2022","value":55.9,"unit":"mm","stated":"4.4\" × 2.2\" × 3.3\" (113 × 55.9 × 73.7mm)","source":{"type":"spec","publisher":"manufacturer","name":"EOTECH G-Series Magnifiers user manual, January 2022 (hosted by T.REX ARMS), p. 6","url":"https://img.trex-arms.com/wp/uploads/2026/03/eotech-g-series-magnifier-user-manual-2022-01.pdf","retrieved":"2026-10-06","via":"harvest"}},{"id":"rear","value":2.115,"unit":"in","pm":0.1,"source":{"type":"photo","photo":"references/eotech-g33 59dba9812333 (EOTECH's g33sts_blk_rv_closed as Arisaka Defense serves it: from behind, in line, 1600 px)","scaleRef":"eotech-g33.sts_mount_height from the clamp's bottom to the hinge knuckles' top at the mount's rear face (373 px: 316 px/in). A close view: the picture's whole width against eotech-g33.width is 304 px/in, and what is nearer the lens reads larger, so the ± is 5% or more","method":"the picture's whole width, the lever's outer face at column 490 to the horizontal knob's at 1158: 669 px. EOTECH's page also says 2.3 (\"4 × 2.3 × 3.3 L × W × H\", its highlights)","via":"harvest"}}],"adopt":{"from":"page","reason":"The maker's page; its manual says the same. The rear view, scaled by the mount's own published height, reads 0.09 in less, inside the 5% a close view is good to: the model is drawn at what the picture reads."}},"height":{"label":"Overall height, the riser fitted (the vertical adjustment's knob to the clamp's bottom)","kind":"length","measurements":[{"id":"page-in","value":3.3,"unit":"in","stated":"4\" x 2.2\" x 3.3\" (102 x 55.9 x 73.7 mm)","source":{"type":"spec","publisher":"manufacturer","name":"eotechinc.com, G33 Magnifier (Tech Specs)","url":"https://www.eotechinc.com/products/eotech-magnifier-g33","retrieved":"2026-10-06","via":"harvest"}},{"id":"page-mm","value":73.7,"unit":"mm","stated":"4\" x 2.2\" x 3.3\" (102 x 55.9 x 73.7 mm)","source":{"type":"spec","publisher":"manufacturer","name":"eotechinc.com, G33 Magnifier (Tech Specs)","url":"https://www.eotechinc.com/products/eotech-magnifier-g33","retrieved":"2026-10-06","via":"harvest"}},{"id":"left","value":3.354,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/eotech-g33 27d853fe5719 (eotechinc.com's gallery: the left side, square on, in line, 2049 px)","scaleRef":"eotech-g33.length across the picture (1654 px: 413.5 px/in) and eotech-g33.sts_mount_length along the mount's top plate (687 px: 413.9 px/in): two published sizes, one scale within 0.1%","method":"the silhouette's top row to its bottom row, 1387 px: the vertical adjustment knob's top to the clamp's bottom, the riser fitted","via":"harvest"}}],"adopt":{"from":"left","reason":"The page's inch and millimetre figures are 10 mm apart; the side view scaled by two published lengths reads the inch figure within its rounding, and is what the model is held to."},"note":"The maker's line contradicts itself: 3.3 in is 83.8 mm, and 73.7 mm is 2.9 in. Its own left side view, the riser fitted, reads 3.35 in from the knob's top to the clamp's bottom (1387 px), and its right side view 3.33 (929 px at 279): the inch figure."},"weight":{"label":"Weight (with its mount)","kind":"mass","measurements":[{"id":"page","value":300,"unit":"g","stated":"Weight with STS™ Mounting System 10.6 oz (300 g)","source":{"type":"spec","publisher":"manufacturer","name":"eotechinc.com, G33 Magnifier (Tech Specs)","url":"https://www.eotechinc.com/products/eotech-magnifier-g33","retrieved":"2026-10-06","via":"harvest"}},{"id":"manual-2022","value":300,"unit":"g","stated":"Weight 10.6 oz (300g)","source":{"type":"spec","publisher":"manufacturer","name":"EOTECH G-Series Magnifiers user manual, January 2022 (hosted by T.REX ARMS), p. 6","url":"https://img.trex-arms.com/wp/uploads/2026/03/eotech-g-series-magnifier-user-manual-2022-01.pdf","retrieved":"2026-10-06","via":"harvest"}},{"id":"pa-table","value":11.2,"unit":"oz","stated":"Weight 11.2 Oz","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, EOTECH G33 Magnifier - Black (G33.STS)","url":"https://www.primaryarms.com/eotech-g33-gen-iii-magnifier-w-sts-mount-black-g33-sts","retrieved":"2026-10-06","via":"harvest"},"note":"The page's own bullet says \"Lightweight and compact (10.6 oz with mount)\": the table's is the older listings' figure."},{"id":"review","value":311,"unit":"g","stated":"the total weight is 303 grams without spacers for cowitness height and 311 grams for 1/3 lower cowitness","source":{"type":"spec","publisher":"review","name":"SPARTANAT, REVIEW: EOTech G33 STS Magnifier","url":"https://spartanat.com/en/review-eotech-g33-fts-magnifier","retrieved":"2026-10-06","via":"harvest"},"note":"A reviewer's own weighing, with the riser; 303 g without it."}],"adopt":{"from":"page","reason":"The maker's current figure, which its manual repeats; a reviewer's scale has it 303 g without the riser and 311 g with."},"note":"The weight of the magnifier set up either way (D95: its 7 mm riser fitted or not), one figure for both. EOTECH's 300 g \"with STS Mounting System\" doesn't say which way; a reviewer weighed both, \"303 grams without spacers for cowitness height and 311 grams for 1/3 lower cowitness\" (SPARTANAT): 8 g between them, EOTECH's figure nearer the first. Those 8 g (0.3 oz) are inside what the sources on file differ by (300 g to Primary Arms' 11.2 oz, 318 g): one figure stands for both ways, and none for the riser alone is taken."},"weight_without_mount":{"label":"Weight of the magnifier alone","kind":"mass","measurements":[{"id":"page","value":221.1,"unit":"g","stated":"Weight without STS™ Mounting System 7.8 oz (221.1 g)","source":{"type":"spec","publisher":"manufacturer","name":"eotechinc.com, G33 Magnifier (Tech Specs)","url":"https://www.eotechinc.com/products/eotech-magnifier-g33","retrieved":"2026-10-06","via":"harvest"}},{"id":"review","value":216,"unit":"g","stated":"The weight is a decent 216 grams","source":{"type":"spec","publisher":"review","name":"SPARTANAT, REVIEW: EOTech G33 STS Magnifier","url":"https://spartanat.com/en/review-eotech-g33-fts-magnifier","retrieved":"2026-10-06","via":"harvest"}},{"id":"manual-2015","value":174,"unit":"g","stated":"Weight: 6.1oz (174g)","source":{"type":"spec","publisher":"manufacturer","name":"L-3 EOTech, User's Manual for G33, Rev E, 2015 (hosted by Brownells)","url":"https://www.brownells.com/globalassets/pdfs/product-pdfs/eotech_g33_magnifier_product_manual.pdf","retrieved":"2026-10-06","via":"harvest"},"note":"The older sheet; with its mount's 81 g it comes to 255 g, 45 g under today's figure for the pair."}],"adopt":{"from":"page","reason":"The maker's current figure; a reviewer's scale reads 2% under it."}},"sts_mount_weight":{"label":"Weight of the STS mount alone","kind":"mass","measurements":[{"id":"manual-2015","value":81,"unit":"g","stated":"Weight: 2.9 oz (81g)","source":{"type":"spec","publisher":"manufacturer","name":"L-3 EOTech, User's Manual for G33, Rev E, 2015 (hosted by Brownells)","url":"https://www.brownells.com/globalassets/pdfs/product-pdfs/eotech_g33_magnifier_product_manual.pdf","retrieved":"2026-10-06","via":"harvest"}},{"id":"review","value":87,"unit":"g","stated":"Mount Weight (No Rating) 87 grams","source":{"type":"spec","publisher":"review","name":"SPARTANAT, REVIEW: EOTech G33 STS Magnifier","url":"https://spartanat.com/en/review-eotech-g33-fts-magnifier","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"manual-2015","reason":"The maker's figure; the reviewer's is the difference of its two weighings (303 − 216)."}},"optical_axis_above_rail_spacer":{"label":"Optical axis above the rail's top, with the 7 mm riser","kind":"length","measurements":[{"id":"review","value":47,"unit":"mm","stated":"Height from Mount to Lens Center (No Rating) 40mm or 47mm with Riser","source":{"type":"spec","publisher":"review","name":"SPARTANAT, REVIEW: EOTech G33 STS Magnifier","url":"https://spartanat.com/en/review-eotech-g33-fts-magnifier","retrieved":"2026-10-06","via":"harvest"},"note":"The reviewer doesn't say which face of the mount it is from; the pictures say the rail's top."},{"id":"photos","value":1.9,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/eotech-g33 27d853fe5719 (the left side) and 59dba9812333 (from behind)","scaleRef":"the left side at 413.5 px/in (eotech-g33.length, eotech-g33.sts_mount_length); the rear view at 316 px/in at the mount's rear face (eotech-g33.sts_mount_height)","method":"axis_above_clamp_bottom (2.220, the left side) less the recess's ceiling above the clamp's bottom in the rear view (rows 1000 ± 5 and 1100: 0.316 in). The ± is the rear view's: a close picture, read at one depth","via":"harvest"}}],"adopt":{"from":"review","reason":"A stated figure, and the pictures read 1.3 mm from it, inside their own ±. One reviewer: provisional."},"note":"EOTECH states no height: its manual says the mount puts the magnifier \"at either an absolute co-witness or lower-third co-witness height\". A reviewer gives two figures, and the maker's pictures, which show the riser fitted, agree with the higher: the eyepiece ring's centre is 2.220 in above the clamp's bottom on the left side view, and the rail's top (the ceiling of the clamp's recess) about 0.32 in above it in the rear view, 1.90 in between."},"optical_axis_above_rail_no_spacer":{"label":"Optical axis above the rail's top, without the riser","kind":"length","measurements":[{"id":"review","value":40,"unit":"mm","stated":"Height from Mount to Lens Center (No Rating) 40mm or 47mm with Riser","source":{"type":"spec","publisher":"review","name":"SPARTANAT, REVIEW: EOTech G33 STS Magnifier","url":"https://spartanat.com/en/review-eotech-g33-fts-magnifier","retrieved":"2026-10-06","via":"harvest"}}]},"riser_thickness":{"label":"The riser's thickness","kind":"length","measurements":[{"id":"manual","value":7,"unit":"mm","stated":"The 7mm riser (included) may be required to align the magnifier optical axis with the sight.","source":{"type":"spec","publisher":"manufacturer","name":"EOTECH G-Series Magnifiers user manual, January 2022 (hosted by T.REX ARMS), p. 6","url":"https://img.trex-arms.com/wp/uploads/2026/03/eotech-g-series-magnifier-user-manual-2022-01.pdf","retrieved":"2026-10-06","via":"harvest"}},{"id":"sides","value":0.28,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/eotech-g33 bac38a8d5ce0 (EOTECH's g33sts_blk_profile_b as Arisaka Defense serves it: the right side, square on, in line, 1600 px)","scaleRef":"eotech-g33.length across the picture (1116 px: 279.0 px/in) and eotech-g33.sts_mount_length along the mount's top plate (462 px: 278.3 px/in): one scale within 0.3%","method":"the band between the mount's top plate and the body's underside: rows 675 to 750 on the right side (0.27 in); 1178 to 1298 on the left side at 413.5 px/in (0.29)","via":"harvest"}}],"adopt":{"from":"manual","reason":"The maker's figure (0.276 in); both side views read it within 0.015 in."}},"eye_relief":{"label":"Eye relief","kind":"length","measurements":[{"id":"page","value":55.9,"unit":"mm","stated":"Eye Relief 2.2\" (55.9 mm)","source":{"type":"spec","publisher":"manufacturer","name":"eotechinc.com, G33 Magnifier (Tech Specs)","url":"https://www.eotechinc.com/products/eotech-magnifier-g33","retrieved":"2026-10-06","via":"harvest"}},{"id":"manual-2022","value":55.9,"unit":"mm","stated":"Eye Relief 2.2\" (55.9mm)","source":{"type":"spec","publisher":"manufacturer","name":"EOTECH G-Series Magnifiers user manual, January 2022 (hosted by T.REX ARMS), p. 6","url":"https://img.trex-arms.com/wp/uploads/2026/03/eotech-g-series-magnifier-user-manual-2022-01.pdf","retrieved":"2026-10-06","via":"harvest"}},{"id":"manual-2015","value":55.8,"unit":"mm","stated":"Eye Relief: 2.2” (55.8mm)","source":{"type":"spec","publisher":"manufacturer","name":"L-3 EOTech, User's Manual for G33, Rev E, 2015 (hosted by Brownells)","url":"https://www.brownells.com/globalassets/pdfs/product-pdfs/eotech_g33_magnifier_product_manual.pdf","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"page","reason":"The maker's page; both manuals say 2.2 in."}},"exit_pupil":{"label":"Exit pupil","kind":"length","measurements":[{"id":"page","value":7.6,"unit":"mm","stated":"Exit Pupil 7.6 mm","source":{"type":"spec","publisher":"manufacturer","name":"eotechinc.com, G33 Magnifier (Tech Specs)","url":"https://www.eotechinc.com/products/eotech-magnifier-g33","retrieved":"2026-10-06","via":"harvest"}}]},"eyepiece_rear_behind_base":{"label":"The eyepiece's rear face behind the mount's centre","kind":"length","measurements":[{"id":"left","value":3.168,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/eotech-g33 27d853fe5719 (eotechinc.com's gallery: the left side, square on, in line, 2049 px)","scaleRef":"eotech-g33.length across the picture (1654 px: 413.5 px/in) and eotech-g33.sts_mount_length along the mount's top plate (687 px: 413.9 px/in): two published sizes, one scale within 0.1%","method":"the diopter ring's rear face at column 1837, the top plate's middle at column 527 (its ends 184 and 870): 1310 px","via":"harvest"}}],"note":"Where the eye looks in: the eye relief runs back from here. The mount's centre is the middle of its top plate, which is the middle of its clamp too (the clamp's bottom runs from 0.135 to 1.528 in behind the front, the plate from 0 to 1.661)."},"sts_mount_length":{"label":"The STS mount's length","kind":"length","measurements":[{"id":"manual-2015","value":42.2,"unit":"mm","stated":"Length: 1.66” (42.2mm)","source":{"type":"spec","publisher":"manufacturer","name":"L-3 EOTech, User's Manual for G33, Rev E, 2015 (hosted by Brownells)","url":"https://www.brownells.com/globalassets/pdfs/product-pdfs/eotech_g33_magnifier_product_manual.pdf","retrieved":"2026-10-06","via":"harvest"}}],"note":"What it spans is read on the side views: the mount's top plate, the longest thing of the mount but its lever."},"sts_mount_height":{"label":"The STS mount's height (the clamp's bottom to the hinge knuckles' top)","kind":"length","measurements":[{"id":"manual-2015","value":30,"unit":"mm","stated":"Height: 1.18” (30mm) Clears common low profile flip up rear iron sights","source":{"type":"spec","publisher":"manufacturer","name":"L-3 EOTech, User's Manual for G33, Rev E, 2015 (hosted by Brownells)","url":"https://www.brownells.com/globalassets/pdfs/product-pdfs/eotech_g33_magnifier_product_manual.pdf","retrieved":"2026-10-06","via":"harvest"}},{"id":"right","value":1.158,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/eotech-g33 bac38a8d5ce0 (EOTECH's g33sts_blk_profile_b as Arisaka Defense serves it: the right side, square on, in line, 1600 px)","scaleRef":"eotech-g33.length across the picture (1116 px: 279.0 px/in) and eotech-g33.sts_mount_length along the mount's top plate (462 px: 278.3 px/in): one scale within 0.3%","method":"the knuckles' top edge at row 732, the clamp's bottom at 1055: 323 px","via":"harvest"}}],"adopt":{"from":"manual-2015","reason":"The maker's figure; the picture reads 2% under it, which is the knuckles' rounded tops seen square on."},"note":"What it spans is read on the right side view: the two hinge knuckles stand above the mount's top plate, their tops 1.158 in above the clamp's bottom; the plate's own top is 1.10."},"axis_above_clamp_bottom":{"label":"Optical axis above the clamp's bottom, the riser fitted","kind":"length","measurements":[{"id":"left","value":2.22,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/eotech-g33 27d853fe5719 (eotechinc.com's gallery: the left side, square on, in line, 2049 px)","scaleRef":"eotech-g33.length across the picture (1654 px: 413.5 px/in) and eotech-g33.sts_mount_length along the mount's top plate (687 px: 413.9 px/in): two published sizes, one scale within 0.1%","method":"the diopter ring's top and bottom at rows 553 and 1118 (columns 1669 to 1789), their middle 835.5; the silhouette's bottom row 1754: 918.5 px. The right side view reads 2.20 (the ring's middle at row 441.5, the bottom at 1055, 279 px/in)","via":"harvest"}}]},"clamp_below_rail":{"label":"The clamp's bottom below the rail's top","kind":"length","measurements":[{"id":"derived","value":0.37,"unit":"in","pm":0.035,"source":{"type":"derived","expr":"{.axis_above_clamp_bottom} - {.optical_axis_above_rail_spacer}","via":"harvest"}},{"id":"rear","value":0.316,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/eotech-g33 59dba9812333 (EOTECH's g33sts_blk_rv_closed as Arisaka Defense serves it: from behind, in line, 1600 px)","scaleRef":"eotech-g33.sts_mount_height from the clamp's bottom to the hinge knuckles' top at the mount's rear face (373 px: 316 px/in). A close view: the picture's whole width against eotech-g33.width is 304 px/in, and what is nearer the lens reads larger, so the ± is 5% or more","method":"the ceiling of the recess between the jaws at row 1000 ± 5 (the last row closed across is 990, the first open 1015), the jaws' bottom at 1100","via":"harvest"}}],"adopt":{"from":"derived","reason":"It puts the axis where the reviewer's figure has it and the clamp's bottom where the side view has it; the rear view's reading is 0.05 in less, inside the two ±."}},"clamp_bottom_y":{"label":"The clamp's bottom in the part frame (y; the rail's top is 0)","kind":"length","measurements":[{"id":"derived","value":-0.37,"unit":"in","pm":0.035,"source":{"type":"derived","expr":"-{.clamp_below_rail}","via":"harvest"},"note":"Where the side profile's origin (the clamp's bottom) sits in the part frame."}]},"objective_tube_od":{"label":"The objective tube's outside diameter","kind":"length","measurements":[{"id":"left","value":1.149,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/eotech-g33 27d853fe5719 (eotechinc.com's gallery: the left side, square on, in line, 2049 px)","scaleRef":"eotech-g33.length across the picture (1654 px: 413.5 px/in) and eotech-g33.sts_mount_length along the mount's top plate (687 px: 413.9 px/in): two published sizes, one scale within 0.1%","method":"the tube's top edge at row 598 (columns 229 to 629), the axis at 835.5: 237.5 px, doubled","via":"harvest"}}],"note":"Its top edge above the axis, doubled: its underside is behind the riser in a side view. T.REX's picture of the parts laid out shows the tube round above a flat foot with two threaded holes."},"eyepiece_ring_od":{"label":"The diopter ring's outside diameter","kind":"length","measurements":[{"id":"left","value":1.369,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/eotech-g33 27d853fe5719 (eotechinc.com's gallery: the left side, square on, in line, 2049 px)","scaleRef":"eotech-g33.length across the picture (1654 px: 413.5 px/in) and eotech-g33.sts_mount_length along the mount's top plate (687 px: 413.9 px/in): two published sizes, one scale within 0.1%","method":"rows 553 to 1118 over columns 1709 to 1789: 566 px","via":"harvest"}}]},"diopter_flutes":{"label":"The flutes round the diopter ring","kind":"count","measurements":[{"id":"rear","value":18,"unit":"count","source":{"type":"photo","photo":"references/eotech-g33 59dba9812333 (EOTECH's g33sts_blk_rv_closed as Arisaka Defense serves it: from behind, in line, 1600 px)","scaleRef":"eotech-g33.sts_mount_height from the clamp's bottom to the hinge knuckles' top at the mount's rear face (373 px: 316 px/in). A close view: the picture's whole width against eotech-g33.width is 304 px/in, and what is nearer the lens reads larger, so the ± is 5% or more","method":"the eyepiece seen from behind, unwrapped about its middle (column 803, row 443) into a strip of angle against radius (references/eotech-g33/work/eyepiece_unwrap.png): eighteen lit lands along the rim at radius 214 to 221 px, 75 to 85 of the strip's 1440 columns apart, a dark flute between each two","via":"harvest"}}],"note":"Counted where the flutes run out at the ring's rear rim, the one view that shows the ring's whole turn. The side views show them along the ring, a land and a flute about 0.23 in from one to the next at its middle, which is what 18 round a 1.37 in ring come to."},"diopter_flute_depth":{"label":"The diopter ring's flutes: their depth","kind":"length","measurements":[{"id":"rear","value":0.028,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/eotech-g33 59dba9812333 (EOTECH's g33sts_blk_rv_closed as Arisaka Defense serves it: from behind, in line, 1600 px)","scaleRef":"eotech-g33.sts_mount_height from the clamp's bottom to the hinge knuckles' top at the mount's rear face (373 px: 316 px/in). A close view: the picture's whole width against eotech-g33.width is 304 px/in, and what is nearer the lens reads larger, so the ± is 5% or more","method":"the eyepiece seen from behind, unwrapped about its middle (column 803, row 443) into a strip of angle against radius (references/eotech-g33/work/eyepiece_unwrap.png): the lands' outer edge at radius 221 px and the flutes' floors at 212, as a share of the ring's own radius there (half of eotech-g33.eyepiece_ring_od): 9 of 221","via":"harvest"}}]},"diopter_flute_angle":{"label":"The diopter ring's flutes: how much of the turn each takes","kind":"angle","measurements":[{"id":"rear","value":11,"unit":"deg","pm":2,"source":{"type":"photo","photo":"references/eotech-g33 59dba9812333 (EOTECH's g33sts_blk_rv_closed as Arisaka Defense serves it: from behind, in line, 1600 px)","scaleRef":"eotech-g33.sts_mount_height from the clamp's bottom to the hinge knuckles' top at the mount's rear face (373 px: 316 px/in). A close view: the picture's whole width against eotech-g33.width is 304 px/in, and what is nearer the lens reads larger, so the ± is 5% or more","method":"the eyepiece seen from behind, unwrapped about its middle (column 803, row 443) into a strip of angle against radius (references/eotech-g33/work/eyepiece_unwrap.png): each land 35 to 40 of the 80 columns from one to the next, each flute the rest","via":"harvest"}}]},"body_height":{"label":"The armoured body, top to bottom","kind":"length","measurements":[{"id":"left","value":1.627,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/eotech-g33 27d853fe5719 (eotechinc.com's gallery: the left side, square on, in line, 2049 px)","scaleRef":"eotech-g33.length across the picture (1654 px: 413.5 px/in) and eotech-g33.sts_mount_length along the mount's top plate (687 px: 413.9 px/in): two published sizes, one scale within 0.1%","method":"rows 503 to 1176 over columns 1109 to 1509: 673 px, 0.805 in above the axis and 0.822 below","via":"harvest"}}]},"top_knob_d":{"label":"The vertical adjustment's knob, across","kind":"length","measurements":[{"id":"left","value":0.7,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/eotech-g33 27d853fe5719 (eotechinc.com's gallery: the left side, square on, in line, 2049 px)","scaleRef":"eotech-g33.length across the picture (1654 px: 413.5 px/in) and eotech-g33.sts_mount_length along the mount's top plate (687 px: 413.9 px/in): two published sizes, one scale within 0.1%","method":"columns 701 to 989 at rows 448 and 488: 289 px; the right side view reads 0.695 (columns 802 to 995)","via":"harvest"}}]},"top_knob_behind_base":{"label":"The vertical adjustment's knob: its axis behind the mount's centre","kind":"length","measurements":[{"id":"left","value":0.769,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/eotech-g33 27d853fe5719 (eotechinc.com's gallery: the left side, square on, in line, 2049 px)","scaleRef":"eotech-g33.length across the picture (1654 px: 413.5 px/in) and eotech-g33.sts_mount_length along the mount's top plate (687 px: 413.9 px/in): two published sizes, one scale within 0.1%","method":"the knob's middle at column 845, the top plate's at 527: 318 px","via":"harvest"}}]},"knob_lugs":{"label":"The lugs round each adjustment knob","kind":"count","measurements":[{"id":"right","value":8,"unit":"count","source":{"type":"photo","photo":"references/eotech-g33 bac38a8d5ce0 (EOTECH's g33sts_blk_profile_b as Arisaka Defense serves it: the right side, square on, in line, 1600 px)","scaleRef":"eotech-g33.length across the picture (1116 px: 279.0 px/in) and eotech-g33.sts_mount_length along the mount's top plate (462 px: 278.3 px/in): one scale within 0.3%","method":"the knob marked R, face on in this view, unwrapped about its middle (column 892.5, row 440) into a strip of angle against radius (references/eotech-g33/work/rknob_unwrap.png): eight dark notches, their middles at 35, 81, 125, 171, 217, 261, 306 and 350 degrees, 44 to 46 degrees apart, and eight lugs between them","via":"harvest"}}],"note":"Counted on the horizontal knob, the one view that shows a knob's whole turn; the vertical one is the same knob by the two side views (two tiers of lugs, one over the other, with a groove between)."},"knob_notch_depth":{"label":"The notches between a knob's lugs: their depth","kind":"length","measurements":[{"id":"right","value":0.036,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/eotech-g33 bac38a8d5ce0 (EOTECH's g33sts_blk_profile_b as Arisaka Defense serves it: the right side, square on, in line, 1600 px)","scaleRef":"eotech-g33.length across the picture (1116 px: 279.0 px/in) and eotech-g33.sts_mount_length along the mount's top plate (462 px: 278.3 px/in): one scale within 0.3%","method":"the knob marked R, face on in this view, unwrapped about its middle (column 892.5, row 440) into a strip of angle against radius (references/eotech-g33/work/rknob_unwrap.png): the lugs' tips at radius 97.5 px (0.349 in, the knob's own radius), the notches' floors at 87.5 px","via":"harvest"}}]},"knob_notch_angle":{"label":"The notches between a knob's lugs: how much of the turn each takes","kind":"angle","measurements":[{"id":"right","value":24,"unit":"deg","pm":3,"source":{"type":"photo","photo":"references/eotech-g33 bac38a8d5ce0 (EOTECH's g33sts_blk_profile_b as Arisaka Defense serves it: the right side, square on, in line, 1600 px)","scaleRef":"eotech-g33.length across the picture (1116 px: 279.0 px/in) and eotech-g33.sts_mount_length along the mount's top plate (462 px: 278.3 px/in): one scale within 0.3%","method":"the knob marked R, face on in this view, unwrapped about its middle (column 892.5, row 440) into a strip of angle against radius (references/eotech-g33/work/rknob_unwrap.png): each notch 90 to 100 of the strip's 1440 columns, each lug 80 to 90","via":"harvest"}}]},"knob_notch_phase":{"label":"Where the knob's notches stood in EOTECH's picture","kind":"angle","measurements":[{"id":"right","value":35,"unit":"deg","pm":3,"source":{"type":"photo","photo":"references/eotech-g33 bac38a8d5ce0 (EOTECH's g33sts_blk_profile_b as Arisaka Defense serves it: the right side, square on, in line, 1600 px)","scaleRef":"eotech-g33.length across the picture (1116 px: 279.0 px/in) and eotech-g33.sts_mount_length along the mount's top plate (462 px: 278.3 px/in): one scale within 0.3%","method":"the knob marked R, face on in this view, unwrapped about its middle (column 892.5, row 440) into a strip of angle against radius (references/eotech-g33/work/rknob_unwrap.png): the first notch's middle, from the direction of the muzzle toward the underside","via":"harvest"}}],"note":"A knob turns: this is only how it was set when photographed, taken so that the model is as pictured."},"side_knob_reach":{"label":"The horizontal adjustment's knob: its outer face right of the optical axis's vertical","kind":"length","measurements":[{"id":"rear","value":1.11,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/eotech-g33 59dba9812333 (EOTECH's g33sts_blk_rv_closed as Arisaka Defense serves it: from behind, in line, 1600 px)","scaleRef":"eotech-g33.sts_mount_height from the clamp's bottom to the hinge knuckles' top at the mount's rear face (373 px: 316 px/in). A close view: the picture's whole width against eotech-g33.width is 304 px/in, and what is nearer the lens reads larger, so the ± is 5% or more","method":"the knob's outer face at column 1158, the middle of the clamp's recess at 807.5: 350.5 px","via":"harvest"}}],"note":"On the rifle's right (the knob marked R). It is the same knob as the one on top, by the two side views, and stands at the same place along the housing, 0.06 in ahead of the mount's rear face: the rear view's scale there is the mount's."},"eyepiece_glass_d":{"label":"The eyepiece's glass, visible diameter","kind":"length","measurements":[{"id":"rear","value":0.95,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/eotech-g33 59dba9812333 (EOTECH's g33sts_blk_rv_closed as Arisaka Defense serves it: from behind, in line, 1600 px)","scaleRef":"eotech-g33.sts_mount_height from the clamp's bottom to the hinge knuckles' top at the mount's rear face (373 px: 316 px/in). A close view: the picture's whole width against eotech-g33.width is 304 px/in, and what is nearer the lens reads larger, so the ± is 5% or more","method":"the glass inside its black retainer, columns 650 to 962 through its middle: 312 px. The eyepiece is the nearest thing to the lens and its scale isn't known better than from 316 px/in (the mount's rear face) to about 340: 0.92 to 0.99 in","via":"harvest"}}]},"objective_glass_d":{"label":"The objective's clear aperture","kind":"length","measurements":[{"id":"derived","value":22.8,"unit":"mm","pm":0.3,"source":{"type":"derived","expr":"{.exit_pupil} * 3","via":"harvest"},"note":"The exit pupil times the magnification: EOTECH's page states both (\"Exit Pupil 7.6 mm\", \"Fixed Magnification 3X\"). The glass that shows may be a little larger than what it passes."}]},"riser_top_above_clamp_bottom":{"label":"The riser's top (the magnifier's foot's underside) above the clamp's bottom","kind":"length","measurements":[{"id":"sides","value":1.385,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/eotech-g33 27d853fe5719 (eotechinc.com's gallery: the left side, square on, in line, 2049 px)","scaleRef":"eotech-g33.length across the picture (1654 px: 413.5 px/in) and eotech-g33.sts_mount_length along the mount's top plate (687 px: 413.9 px/in): two published sizes, one scale within 0.1%","method":"row 1178 on the left side (1.393 in); row 675 on the right side at 279 px/in (1.362): their middle, and the ± covers both","via":"harvest"}}]},"plate_top_above_clamp_bottom":{"label":"The mount's top plate: its top above the clamp's bottom","kind":"length","measurements":[{"id":"sides","value":1.1,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/eotech-g33 27d853fe5719 (eotechinc.com's gallery: the left side, square on, in line, 2049 px)","scaleRef":"eotech-g33.length across the picture (1654 px: 413.5 px/in) and eotech-g33.sts_mount_length along the mount's top plate (687 px: 413.9 px/in): two published sizes, one scale within 0.1%","method":"row 1298 on the left side (1.103 in); row 750 on the right side at 279 px/in (1.093)","via":"harvest"}}]},"plate_bottom_above_clamp_bottom":{"label":"The mount's top plate: its underside above the clamp's bottom","kind":"length","measurements":[{"id":"sides","value":0.866,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/eotech-g33 27d853fe5719 (eotechinc.com's gallery: the left side, square on, in line, 2049 px)","scaleRef":"eotech-g33.length across the picture (1654 px: 413.5 px/in) and eotech-g33.sts_mount_length along the mount's top plate (687 px: 413.9 px/in): two published sizes, one scale within 0.1%","method":"row 1398 on the left side (0.861 in); row 812 on the right side at 279 px/in (0.871)","via":"harvest"}}]},"riser_length":{"label":"The riser's length along the rail","kind":"length","measurements":[{"id":"left","value":1.608,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/eotech-g33 27d853fe5719 (eotechinc.com's gallery: the left side, square on, in line, 2049 px)","scaleRef":"eotech-g33.length across the picture (1654 px: 413.5 px/in) and eotech-g33.sts_mount_length along the mount's top plate (687 px: 413.9 px/in): two published sizes, one scale within 0.1%","method":"columns 193 to 857 over rows 1188 to 1288: 665 px; 1.602 on the right side (columns 895 to 1341)","via":"harvest"}}]},"riser_width":{"label":"The riser's width across the rail","kind":"length","measurements":[{"id":"rear","value":0.75,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/eotech-g33 59dba9812333 (EOTECH's g33sts_blk_rv_closed as Arisaka Defense serves it: from behind, in line, 1600 px)","scaleRef":"eotech-g33.sts_mount_height from the clamp's bottom to the hinge knuckles' top at the mount's rear face (373 px: 316 px/in). A close view: the picture's whole width against eotech-g33.width is 304 px/in, and what is nearer the lens reads larger, so the ± is 5% or more","method":"the block under the body, columns 688 to 924 at rows 715 and 740: 237 px","via":"harvest"}}]},"plate_width":{"label":"The mount's top plate: its width across the rail, without the arm to the hinge","kind":"length","measurements":[{"id":"rear","value":0.64,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/eotech-g33 59dba9812333 (EOTECH's g33sts_blk_rv_closed as Arisaka Defense serves it: from behind, in line, 1600 px)","scaleRef":"eotech-g33.sts_mount_height from the clamp's bottom to the hinge knuckles' top at the mount's rear face (373 px: 316 px/in). A close view: the picture's whole width against eotech-g33.width is 304 px/in, and what is nearer the lens reads larger, so the ± is 5% or more","method":"columns 707 to 909 at row 790: 203 px","via":"harvest"}}]},"base_top_above_clamp_bottom":{"label":"The clamp base's top (the lever's top edge) above the clamp's bottom","kind":"length","measurements":[{"id":"sides","value":0.555,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/eotech-g33 27d853fe5719 (eotechinc.com's gallery: the left side, square on, in line, 2049 px)","scaleRef":"eotech-g33.length across the picture (1654 px: 413.5 px/in) and eotech-g33.sts_mount_length along the mount's top plate (687 px: 413.9 px/in): two published sizes, one scale within 0.1%","method":"the lever's top edge at rows 1518 to 1528 on the left side (0.571 to 0.547 in); the base's top at row 900 on the right side at 279 px/in (0.555)","via":"harvest"}}]},"clamp_length":{"label":"The clamp's length along the rail","kind":"length","measurements":[{"id":"left","value":1.395,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/eotech-g33 27d853fe5719 (eotechinc.com's gallery: the left side, square on, in line, 2049 px)","scaleRef":"eotech-g33.length across the picture (1654 px: 413.5 px/in) and eotech-g33.sts_mount_length along the mount's top plate (687 px: 413.9 px/in): two published sizes, one scale within 0.1%","method":"the silhouette's lowest rows (1728 to 1748), columns 240 to 816: 577 px, its middle at column 528, under the top plate's (527). The right side reads 1.398 (columns 923 to 1312)","via":"harvest"}}]},"lever_tail_behind_base":{"label":"The quick-detach lever's tail end, behind the mount's centre (closed)","kind":"length","measurements":[{"id":"left","value":1.381,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/eotech-g33 27d853fe5719 (eotechinc.com's gallery: the left side, square on, in line, 2049 px)","scaleRef":"eotech-g33.length across the picture (1654 px: 413.5 px/in) and eotech-g33.sts_mount_length along the mount's top plate (687 px: 413.9 px/in): two published sizes, one scale within 0.1%","method":"the lever's tail end at column 1098, the top plate's middle at 527: 571 px. From the right side, seen past the mount, its end reads 1.31","via":"harvest"}}],"note":"The lever is on the rifle's left and lies along the clamp, its tail to the rear."},"lever_bottom_above_clamp_bottom":{"label":"The quick-detach lever's underside above the clamp's bottom","kind":"length","measurements":[{"id":"left","value":0.085,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/eotech-g33 27d853fe5719 (eotechinc.com's gallery: the left side, square on, in line, 2049 px)","scaleRef":"eotech-g33.length across the picture (1654 px: 413.5 px/in) and eotech-g33.sts_mount_length along the mount's top plate (687 px: 413.9 px/in): two published sizes, one scale within 0.1%","method":"the tail's underside at row 1719 behind the clamp (columns 830 to 1098), the bottom at 1754","via":"harvest"}}]},"lever_thickness":{"label":"The quick-detach lever's thickness across the rail","kind":"length","measurements":[{"id":"rear","value":0.2,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/eotech-g33 59dba9812333 (EOTECH's g33sts_blk_rv_closed as Arisaka Defense serves it: from behind, in line, 1600 px)","scaleRef":"eotech-g33.sts_mount_height from the clamp's bottom to the hinge knuckles' top at the mount's rear face (373 px: 316 px/in). A close view: the picture's whole width against eotech-g33.width is 304 px/in, and what is nearer the lens reads larger, so the ± is 5% or more","method":"the outermost piece on the left of the clamp, columns 490 to 556 at rows 940 to 1065: 66 px","via":"harvest"}}]},"base_left_of_centre":{"label":"The clamp's left face (the lever's outer face), left of the rail's centre","kind":"length","measurements":[{"id":"rear","value":1,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/eotech-g33 59dba9812333 (EOTECH's g33sts_blk_rv_closed as Arisaka Defense serves it: from behind, in line, 1600 px)","scaleRef":"eotech-g33.sts_mount_height from the clamp's bottom to the hinge knuckles' top at the mount's rear face (373 px: 316 px/in). A close view: the picture's whole width against eotech-g33.width is 304 px/in, and what is nearer the lens reads larger, so the ± is 5% or more","method":"column 490, the middle of the recess between the jaws at 807.5: 317.5 px","via":"harvest"}}]},"hinge_axis_above_clamp_bottom":{"label":"The mount's hinge axis above the clamp's bottom","kind":"length","measurements":[{"id":"rear","value":0.871,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/eotech-g33 59dba9812333 (EOTECH's g33sts_blk_rv_closed as Arisaka Defense serves it: from behind, in line, 1600 px)","scaleRef":"eotech-g33.sts_mount_height from the clamp's bottom to the hinge knuckles' top at the mount's rear face (373 px: 316 px/in). A close view: the picture's whole width against eotech-g33.width is 304 px/in, and what is nearer the lens reads larger, so the ± is 5% or more","method":"the hinge pin's bright end, columns 976 to 1076 and rows 775 to 873, its middle at row 824.8; the jaws' bottom at 1100: 275 px","via":"harvest"}},{"id":"right","value":0.85,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/eotech-g33 bac38a8d5ce0 (EOTECH's g33sts_blk_profile_b as Arisaka Defense serves it: the right side, square on, in line, 1600 px)","scaleRef":"eotech-g33.length across the picture (1116 px: 279.0 px/in) and eotech-g33.sts_mount_length along the mount's top plate (462 px: 278.3 px/in): one scale within 0.3%","method":"the knuckles' rounded top at row 732 and their radius (half of hinge_knuckle_d): the axis at row 818","via":"harvest"}}],"adopt":{"from":"rear","reason":"The pin's own end, seen end on; the side view's reading comes through the knuckle's radius and agrees within 0.02 in."}},"hinge_axis_right_of_centre":{"label":"The mount's hinge axis to the right of the rail's centre","kind":"length","measurements":[{"id":"rear","value":0.69,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/eotech-g33 59dba9812333 (EOTECH's g33sts_blk_rv_closed as Arisaka Defense serves it: from behind, in line, 1600 px)","scaleRef":"eotech-g33.sts_mount_height from the clamp's bottom to the hinge knuckles' top at the mount's rear face (373 px: 316 px/in). A close view: the picture's whole width against eotech-g33.width is 304 px/in, and what is nearer the lens reads larger, so the ± is 5% or more","method":"the pin's middle at column 1025.4, the middle of the recess between the jaws at 807.5: 218 px","via":"harvest"}}],"note":"On the rifle's right as EOTECH pictures it: the rear views have the pin on the picture's right with the knob marked R, and the right side view has the hinge toward the lens."},"hinge_pin_d":{"label":"The hinge pin's diameter","kind":"length","measurements":[{"id":"rear","value":0.316,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/eotech-g33 59dba9812333 (EOTECH's g33sts_blk_rv_closed as Arisaka Defense serves it: from behind, in line, 1600 px)","scaleRef":"eotech-g33.sts_mount_height from the clamp's bottom to the hinge knuckles' top at the mount's rear face (373 px: 316 px/in). A close view: the picture's whole width against eotech-g33.width is 304 px/in, and what is nearer the lens reads larger, so the ± is 5% or more","method":"its bright end, 100 px across","via":"harvest"}}]},"hinge_knuckle_d":{"label":"The hinge knuckles' outside diameter","kind":"length","measurements":[{"id":"rear","value":0.62,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/eotech-g33 59dba9812333 (EOTECH's g33sts_blk_rv_closed as Arisaka Defense serves it: from behind, in line, 1600 px)","scaleRef":"eotech-g33.sts_mount_height from the clamp's bottom to the hinge knuckles' top at the mount's rear face (373 px: 316 px/in). A close view: the picture's whole width against eotech-g33.width is 304 px/in, and what is nearer the lens reads larger, so the ± is 5% or more","method":"the rounded housing about the pin: its top at row 727, 98 px above the pin's middle, and its right at column 1120, 95 px from it","via":"harvest"}}]},"hinge_block_length":{"label":"The hinge's length along the rail (both knuckles and the barrel between them)","kind":"length","measurements":[{"id":"right","value":1.394,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/eotech-g33 bac38a8d5ce0 (EOTECH's g33sts_blk_profile_b as Arisaka Defense serves it: the right side, square on, in line, 1600 px)","scaleRef":"eotech-g33.length across the picture (1116 px: 279.0 px/in) and eotech-g33.sts_mount_length along the mount's top plate (462 px: 278.3 px/in): one scale within 0.3%","method":"columns 922 to 1310 at rows 817 to 862: 389 px, its middle 0.005 in behind the top plate's (column 1117.5)","via":"harvest"}}]},"hinge_knuckle_length":{"label":"Each hinge knuckle's length along the rail","kind":"length","measurements":[{"id":"right","value":0.37,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/eotech-g33 bac38a8d5ce0 (EOTECH's g33sts_blk_profile_b as Arisaka Defense serves it: the right side, square on, in line, 1600 px)","scaleRef":"eotech-g33.length across the picture (1116 px: 279.0 px/in) and eotech-g33.sts_mount_length along the mount's top plate (462 px: 278.3 px/in): one scale within 0.3%","method":"row 877: the rear knuckle columns 923 to 1027 (0.376), the front one 1209 to 1310 (0.366), the barrel 1036 to 1198 between","via":"harvest"}}]},"hinge_web_inner_right_of_centre":{"label":"The wall under the hinge: its inner face right of the rail's centre","kind":"length","measurements":[{"id":"rear","value":0.13,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/eotech-g33 59dba9812333 (EOTECH's g33sts_blk_rv_closed as Arisaka Defense serves it: from behind, in line, 1600 px)","scaleRef":"eotech-g33.sts_mount_height from the clamp's bottom to the hinge knuckles' top at the mount's rear face (373 px: 316 px/in). A close view: the picture's whole width against eotech-g33.width is 304 px/in, and what is nearer the lens reads larger, so the ± is 5% or more","method":"the wall's left edge at column 849 at row 865, the middle of the recess between the jaws at 807.5: 41.5 px; at row 890 it is at column 867 (0.19)","via":"harvest"}}],"note":"The hinge stands on a wall up from the clamp's right side; the plate's underside is open to the left of it (the backdrop shows there in the rear view)."},"hinge_barrel_d":{"label":"The hinge barrel's diameter (the plate's arm, between the knuckles)","kind":"length","measurements":[{"id":"right","value":0.5,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/eotech-g33 bac38a8d5ce0 (EOTECH's g33sts_blk_profile_b as Arisaka Defense serves it: the right side, square on, in line, 1600 px)","scaleRef":"eotech-g33.length across the picture (1116 px: 279.0 px/in) and eotech-g33.sts_mount_length along the mount's top plate (462 px: 278.3 px/in): one scale within 0.3%","method":"the barrel between the knuckles, its top at row 740 under the plate's edge and its underside at 880, above the two gaps the backdrop shows through: 140 px","via":"harvest"}}]},"clamp_nut_d":{"label":"The clamp's adjustment nut on the mount's right face, across","kind":"length","measurements":[{"id":"right","value":0.36,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/eotech-g33 bac38a8d5ce0 (EOTECH's g33sts_blk_profile_b as Arisaka Defense serves it: the right side, square on, in line, 1600 px)","scaleRef":"eotech-g33.length across the picture (1116 px: 279.0 px/in) and eotech-g33.sts_mount_length along the mount's top plate (462 px: 278.3 px/in): one scale within 0.3%","method":"the slotted round nut under the hinge barrel, columns 1070 to 1170: 100 px","via":"harvest"}}]},"clamp_nut_above_clamp_bottom":{"label":"The clamp's adjustment nut: its axis above the clamp's bottom","kind":"length","measurements":[{"id":"right","value":0.32,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/eotech-g33 bac38a8d5ce0 (EOTECH's g33sts_blk_profile_b as Arisaka Defense serves it: the right side, square on, in line, 1600 px)","scaleRef":"eotech-g33.length across the picture (1116 px: 279.0 px/in) and eotech-g33.sts_mount_length along the mount's top plate (462 px: 278.3 px/in): one scale within 0.3%","method":"its middle at row 965, the bottom at 1055; along the rail it is at column 1120, under the plate's middle (1117.5)","via":"harvest"}}]},"flip_angle":{"label":"How far the magnifier swings to the side on its mount","kind":"angle","measurements":[{"id":"rear-views","value":93.5,"unit":"deg","pm":3,"source":{"type":"photo","photo":"references/eotech-g33 59dba9812333 (from behind, in line) and 5a29b52fe5bf (from behind, swung aside; EOTECH's g33sts_blk_rv_open as Arisaka Defense serves it)","scaleRef":"none needed: an angle between two lines, each within one picture","method":"in line, the pin at (1025.4, 824.8) and the eyepiece's bright spot at (803.6, 444.4): 30.2 degrees left of upright; swung aside, the pin at (714, 677) and the spot at (1107.8, 478.6): 26.8 degrees above level. The ± is the spot's: it is the far aperture seen through the lenses, not a mark on the housing","via":"harvest"}}],"note":"To the rifle's right as EOTECH pictures it. No page states the angle; it is read from the maker's two rear views, in line and swung aside, as the turn of the line from the hinge pin to the bright spot in the eyepiece. That line is the same length in both (440.3 and 441.0 px), which is what a turn about the pin leaves alone."}}},{"subject":"eotech-g45","title":"EOTECH G45 5X Magnifier on its Switch-to-Side (STS) mount, the 7 mm riser fitted","dimensions":{"length":{"label":"Overall length (the objective's front face to the diopter ring's rear face)","kind":"length","measurements":[{"id":"page","value":99,"unit":"mm","stated":"L × W × H 3.9\" x 2.3\" x 3.3\" (99 x 58.4 x 83.8 mm)","source":{"type":"spec","publisher":"manufacturer","name":"eotechinc.com, G45 Magnifier (Tech Specs)","url":"https://www.eotechinc.com/products/eotech-magnifier-g45","retrieved":"2026-10-12","via":"harvest"}},{"id":"catalog","value":99,"unit":"mm","stated":"L × W × H 3.9” × 2.3” × 3.3” / 99 × 58.4 × 83.8mm","source":{"type":"spec","publisher":"manufacturer","name":"EOTECH full catalogue (PDF), p. 22","url":"https://cdn.shopify.com/s/files/1/0698/3044/3191/files/EOTECH_Full_Catalog.pdf","retrieved":"2026-10-12","via":"harvest"}},{"id":"manual-2022","value":99,"unit":"mm","stated":"L×W×H 3.9\" × 2.3\" × 3.3\" (99 × 58.4 × 83.8mm)","source":{"type":"spec","publisher":"manufacturer","name":"EOTECH G-Series Magnifiers user manual, January 2022 (hosted by T.REX ARMS), p. 7","url":"https://img.trex-arms.com/wp/uploads/2026/03/eotech-g-series-magnifier-user-manual-2022-01.pdf","retrieved":"2026-10-12","via":"harvest"}},{"id":"trex","value":99,"unit":"mm","stated":"L X W X H 3.9\" x 2.3\" x 3.3\" (99 x 58.4 x 83.8 mm)","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, EOTECH G45 5x Magnifier","url":"https://www.trex-arms.com/store/eotech-g45-5x-magnifier-652617","retrieved":"2026-10-12","via":"harvest"}},{"id":"pa","value":3.9,"unit":"in","stated":"Length: 3.9”","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, EOTECH G45 5X Magnifier - Black (G45.STS)","url":"https://www.primaryarms.com/eotech-g45-5x-magnifier-black","retrieved":"2026-10-12","via":"harvest"}},{"id":"silencer","value":3.9,"unit":"in","stated":"Length: 3.9 In","source":{"type":"spec","publisher":"retailer","name":"Silencer Shop, EOTECH G45 5X Magnifier (EO-G45.STS)","url":"https://www.silencershop.com/eotech-g45.html","retrieved":"2026-10-12","via":"harvest"}},{"id":"optics-trade-prose","value":116.3,"unit":"mm","stated":"Compact length of approximately 116.3 mm (4.58 in).","source":{"type":"spec","publisher":"retailer","name":"Optics Trade, EOTech Magnifier G45","url":"https://www.optics-trade.eu/us/eotech-magnifier-g45.html","retrieved":"2026-10-12","via":"harvest"},"note":"The shop's own prose; its table on the same page says \"Length. 3.90 inch (99.00 mm)\"."},{"id":"left","value":3.751,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/eotech-g45 64be77ba9788 (eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px)","scaleRef":"eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in)","method":"the objective's front edge at column 219 (rows 678 to 834) and the diopter ring's rear edge at 1864: 1645 px. The ± is 1%: three side views scaled each by its own picture of the mount's top plate read 3.75, 3.76 and 3.83","via":"harvest"}}],"adopt":{"from":"left","reason":"What the maker's own side view reads at a scale two of its published sizes agree on, and what the model is held to. The published 3.9 in is 4% more than any of three side views has between the magnifier's two end faces, and no page says what it spans."},"note":"EOTECH publishes 3.9 in everywhere and says nowhere what it spans. Its own left side view, at the scale where the mount's published 1.66 in and the kit's published 3.3 in height agree within 0.2%, has 1645 px from the objective's front to the diopter ring's rear: 3.75 in; the whole picture, the mount's top plate standing 5 px ahead of the objective, is 1650 px (3.76). Rifle Supply's right side view reads 3.76 at its own plate's scale and Primary Arms' left side view 3.83. At 3.9 in the picture would be 62 px longer than it is. The diopter ring turns to focus and may stand further out than pictured; a seller's 116.3 mm fits nothing in any picture."},"width":{"label":"Overall width","kind":"length","measurements":[{"id":"page","value":58.4,"unit":"mm","stated":"L × W × H 3.9\" x 2.3\" x 3.3\" (99 x 58.4 x 83.8 mm)","source":{"type":"spec","publisher":"manufacturer","name":"eotechinc.com, G45 Magnifier (Tech Specs)","url":"https://www.eotechinc.com/products/eotech-magnifier-g45","retrieved":"2026-10-12","via":"harvest"}},{"id":"manual-2022","value":58.4,"unit":"mm","stated":"L×W×H 3.9\" × 2.3\" × 3.3\" (99 × 58.4 × 83.8mm)","source":{"type":"spec","publisher":"manufacturer","name":"EOTECH G-Series Magnifiers user manual, January 2022 (hosted by T.REX ARMS), p. 7","url":"https://img.trex-arms.com/wp/uploads/2026/03/eotech-g-series-magnifier-user-manual-2022-01.pdf","retrieved":"2026-10-12","via":"harvest"}},{"id":"silencer","value":2.3,"unit":"in","stated":"Width: 2.3 In","source":{"type":"spec","publisher":"retailer","name":"Silencer Shop, EOTECH G45 5X Magnifier (EO-G45.STS)","url":"https://www.silencershop.com/eotech-g45.html","retrieved":"2026-10-12","via":"harvest"}}],"adopt":{"from":"page","reason":"The maker's figure, which its manual and a seller repeat."},"note":"No view square across the magnifier is on file: the published figure can't be held against a picture. The model is 2.12 in across: the lever's face 1.0 in left of the rail's middle (the same mount's, the G33's ledger) and the horizontal knob's 1.12 in right of it (side_knob_reach, worked out from the side view): see the part's approximations."},"height":{"label":"Overall height, the riser fitted (the vertical adjustment's knob to the clamp's bottom)","kind":"length","measurements":[{"id":"page","value":83.8,"unit":"mm","stated":"L × W × H 3.9\" x 2.3\" x 3.3\" (99 x 58.4 x 83.8 mm)","source":{"type":"spec","publisher":"manufacturer","name":"eotechinc.com, G45 Magnifier (Tech Specs)","url":"https://www.eotechinc.com/products/eotech-magnifier-g45","retrieved":"2026-10-12","via":"harvest"}},{"id":"catalog","value":83.8,"unit":"mm","stated":"L × W × H 3.9” × 2.3” × 3.3” / 99 × 58.4 × 83.8mm","source":{"type":"spec","publisher":"manufacturer","name":"EOTECH full catalogue (PDF), p. 22","url":"https://cdn.shopify.com/s/files/1/0698/3044/3191/files/EOTECH_Full_Catalog.pdf","retrieved":"2026-10-12","via":"harvest"}},{"id":"manual-2022","value":83.8,"unit":"mm","stated":"L×W×H 3.9\" × 2.3\" × 3.3\" (99 × 58.4 × 83.8mm)","source":{"type":"spec","publisher":"manufacturer","name":"EOTECH G-Series Magnifiers user manual, January 2022 (hosted by T.REX ARMS), p. 7","url":"https://img.trex-arms.com/wp/uploads/2026/03/eotech-g-series-magnifier-user-manual-2022-01.pdf","retrieved":"2026-10-12","via":"harvest"}},{"id":"left","value":3.304,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/eotech-g45 64be77ba9788 (eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px)","scaleRef":"eotech-g45.sts_mount_length along the mount's top plate alone (728 px: 438.2 px/in)","method":"the silhouette's top row to its bottom row, 282 to 1729: 1448 px, the vertical adjustment knob's top to the clamp's bottom","via":"harvest"}}],"adopt":{"from":"page","reason":"The maker's figure, in its page, catalogue and manual; its own side view reads 0.005 in more at the scale the mount's published length gives, inside its ±."},"note":"The published figure doesn't say whether the riser is fitted; EOTECH's own picture, which has it, reads the figure within 0.2% at the scale the mount's own published length gives: with the riser."},"weight":{"label":"Weight (with its mount)","kind":"mass","measurements":[{"id":"page","value":362.9,"unit":"g","stated":"Weight with STS ™ Mounting System 12.8 oz (362.9 g)","source":{"type":"spec","publisher":"manufacturer","name":"eotechinc.com, G45 Magnifier (Tech Specs)","url":"https://www.eotechinc.com/products/eotech-magnifier-g45","retrieved":"2026-10-12","via":"harvest"}},{"id":"catalog","value":362.9,"unit":"g","stated":"WEIGHT 12.8oz / 362.9g","source":{"type":"spec","publisher":"manufacturer","name":"EOTECH full catalogue (PDF), p. 22","url":"https://cdn.shopify.com/s/files/1/0698/3044/3191/files/EOTECH_Full_Catalog.pdf","retrieved":"2026-10-12","via":"harvest"}},{"id":"manual-2022","value":362.9,"unit":"g","stated":"Weight 12.8 oz (362.9g)","source":{"type":"spec","publisher":"manufacturer","name":"EOTECH G-Series Magnifiers user manual, January 2022 (hosted by T.REX ARMS), p. 7","url":"https://img.trex-arms.com/wp/uploads/2026/03/eotech-g-series-magnifier-user-manual-2022-01.pdf","retrieved":"2026-10-12","via":"harvest"}},{"id":"trex","value":362.9,"unit":"g","stated":"Weight 12.8 oz (362.9 g)","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, EOTECH G45 5x Magnifier","url":"https://www.trex-arms.com/store/eotech-g45-5x-magnifier-652617","retrieved":"2026-10-12","via":"harvest"}},{"id":"optics-trade-prose","value":368.5,"unit":"g","stated":"Weight: Approximately 368.5 g (13.0 oz) with mount","source":{"type":"spec","publisher":"retailer","name":"Optics Trade, EOTech Magnifier G45","url":"https://www.optics-trade.eu/us/eotech-magnifier-g45.html","retrieved":"2026-10-12","via":"harvest"},"note":"The shop's own prose; its table on the same page says 12.80 oz."}],"adopt":{"from":"page","reason":"The maker's figure, which its catalogue and manual repeat; one shop's prose has 5.6 g more and its own table the maker's 12.8 oz."},"note":"The weight of the magnifier set up either way (D95: its 7 mm riser fitted or not), one figure for both. EOTECH's 362.9 g \"with STS Mounting System\" doesn't say which way. The riser is the G33's (the same STS kit), which a reviewer's two weighings of that magnifier put at 8 g (0.3 oz; eotech-g33.weight), about what the sources on file here differ by (362.9 to 368.5 g): one figure stands for both ways, and none for the riser alone is taken."},"weight_without_mount":{"label":"Weight of the magnifier alone","kind":"mass","measurements":[{"id":"page","value":269.3,"unit":"g","stated":"Weight without STS ™ Mounting System 9.5 oz (269.3 g)","source":{"type":"spec","publisher":"manufacturer","name":"eotechinc.com, G45 Magnifier (Tech Specs)","url":"https://www.eotechinc.com/products/eotech-magnifier-g45","retrieved":"2026-10-12","via":"harvest"}}]},"mount_and_riser_weight":{"label":"Weight of the STS mount as the kit has it (the mount, the riser and its screws)","kind":"mass","measurements":[{"id":"derived","value":93.6,"unit":"g","pm":0.1,"source":{"type":"derived","expr":"{.weight} - {.weight_without_mount}","via":"harvest"}}],"note":"The difference of EOTECH's two figures for the G45. Its 2015 sheet has the mount alone at 81 g, and a reviewer's scale 87 g (the G33's ledger, sts_mount_weight)."},"eye_relief":{"label":"Eye relief","kind":"length","measurements":[{"id":"page","value":66,"unit":"mm","stated":"Eye Relief 2.6\" (66 mm)","source":{"type":"spec","publisher":"manufacturer","name":"eotechinc.com, G45 Magnifier (Tech Specs)","url":"https://www.eotechinc.com/products/eotech-magnifier-g45","retrieved":"2026-10-12","via":"harvest"}},{"id":"manual-2022","value":66,"unit":"mm","stated":"Eye Relief 2.6\" (66mm)","source":{"type":"spec","publisher":"manufacturer","name":"EOTECH G-Series Magnifiers user manual, January 2022 (hosted by T.REX ARMS), p. 7","url":"https://img.trex-arms.com/wp/uploads/2026/03/eotech-g-series-magnifier-user-manual-2022-01.pdf","retrieved":"2026-10-12","via":"harvest"}},{"id":"catalog","value":66,"unit":"mm","stated":"2.6” / 66mm","source":{"type":"spec","publisher":"manufacturer","name":"EOTECH full catalogue (PDF), p. 22","url":"https://cdn.shopify.com/s/files/1/0698/3044/3191/files/EOTECH_Full_Catalog.pdf","retrieved":"2026-10-12","via":"harvest"}},{"id":"trex","value":66,"unit":"mm","stated":"Eye Relief 2.6\" (66mm)","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, EOTECH G45 5x Magnifier","url":"https://www.trex-arms.com/store/eotech-g45-5x-magnifier-652617","retrieved":"2026-10-12","via":"harvest"}}],"adopt":{"from":"page","reason":"The maker's page; its manual, its catalogue and a seller say the same."}},"field_of_view":{"label":"Field of view","kind":"angle","measurements":[{"id":"manual-2022","value":4.4,"unit":"deg","stated":"Field-of-View 4.4°","source":{"type":"spec","publisher":"manufacturer","name":"EOTECH G-Series Magnifiers user manual, January 2022 (hosted by T.REX ARMS), p. 7","url":"https://img.trex-arms.com/wp/uploads/2026/03/eotech-g-series-magnifier-user-manual-2022-01.pdf","retrieved":"2026-10-12","via":"harvest"}},{"id":"catalog","value":4.4,"unit":"deg","stated":"4.4˚","source":{"type":"spec","publisher":"manufacturer","name":"EOTECH full catalogue (PDF), p. 22","url":"https://cdn.shopify.com/s/files/1/0698/3044/3191/files/EOTECH_Full_Catalog.pdf","retrieved":"2026-10-12","via":"harvest"}},{"id":"page","value":4,"unit":"deg","stated":"Field-Of-View 4°","source":{"type":"spec","publisher":"manufacturer","name":"eotechinc.com, G45 Magnifier (Tech Specs)","url":"https://www.eotechinc.com/products/eotech-magnifier-g45","retrieved":"2026-10-12","via":"harvest"}}],"adopt":{"from":"manual-2022","reason":"The manual's and the catalogue's figure; the page's 4° is the same figure without its tenth."},"note":"EOTECH's page rounds it to a whole degree, and its Exit Pupil row repeats that (\"Exit Pupil 4°\"): a slip, and no exit pupil is stated for the G45."},"exit_pupil":{"label":"Exit pupil","kind":"length","measurements":[],"note":"Not stated for the G45: EOTECH's page has the row, and in it the field of view again (\"Exit Pupil 4°\"). The G33's page states its own (7.6 mm). With one seller's \"Objective 25\" and the 5X it would be 5 mm; nothing is drawn from it."},"optical_axis_above_rail_spacer":{"label":"Optical axis above the rail's top, with the 7 mm riser","kind":"length","measurements":[{"id":"derived","value":1.826,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{.axis_above_clamp_bottom} - {.clamp_below_rail}","via":"harvest"}}],"note":"No page states a height: EOTECH's manual says the mount puts the magnifier \"at either an absolute co-witness or lower-third co-witness height\". It is the diopter ring's middle over the clamp's bottom on EOTECH's left side view of the G45 (2.196 in), less how far the same mount's clamp reaches under the rail's top (the G33's ledger: 0.37 in, which puts the G33's axis at a reviewer's 47 mm). T.REX ARMS' staff, of what it lines up with: \"the G45 on a spacer with a lined up with a 193 Aimpoint T2 looks perfect\"."},"optical_axis_above_rail_no_spacer":{"label":"Optical axis above the rail's top, without the riser","kind":"length","measurements":[{"id":"derived","value":1.55,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.optical_axis_above_rail_spacer} - {.riser_thickness}","via":"harvest"}},{"id":"pa-left","value":1.614,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/eotech-g45 863730d15d11 (Primary Arms' G45.STS_02: the left side, square on, in line, no riser, 2200 px)","scaleRef":"eotech-g45.sts_mount_length along the mount's top plate (656 px: 394.8 px/in)","method":"the diopter ring's middle (rows 249 to 842) over the top plate's underside (row 987): 441.5 px, 1.118 in; plus eotech-g45.plate_bottom_above_clamp_bottom, less eotech-g45.clamp_below_rail","via":"harvest"}}],"adopt":{"from":"derived","reason":"The maker's own figure for the riser. The picture's reading is kept beside it: 0.06 in more, about what two side views' heights differ by."},"note":"Not drawn: the model has the riser fitted. Two routes: the maker's 7 mm taken off the height with the riser, and Primary Arms' left side view of a G45 without it, where the diopter ring's middle is 1.118 in over the mount's top plate's underside (441.5 px at its own plate's scale) against 1.346 in on EOTECH's view with the riser: 0.23 in between the two pictures for a riser of 0.276. The side views' heights differ by 2% from one to the next, which on a height of 2.2 in is as much as that."},"riser_thickness":{"label":"The riser's thickness","kind":"length","measurements":[{"id":"manual","value":7,"unit":"mm","stated":"The 7mm riser (included) may be required to align the magnifier optical axis with the sight.","source":{"type":"spec","publisher":"manufacturer","name":"EOTECH G-Series Magnifiers user manual, January 2022 (hosted by T.REX ARMS), p. 7","url":"https://img.trex-arms.com/wp/uploads/2026/03/eotech-g-series-magnifier-user-manual-2022-01.pdf","retrieved":"2026-10-12","via":"harvest"}}]},"axis_above_clamp_bottom":{"label":"Optical axis above the clamp's bottom, the riser fitted","kind":"length","measurements":[{"id":"left","value":2.196,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/eotech-g45 64be77ba9788 (eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px)","scaleRef":"eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in)","method":"the diopter ring's top and bottom rows 435 and 1097 over columns 1762 to 1846, their middle 766.5; the silhouette's bottom edge 1729.5: 963 px. Rifle Supply's right side view reads 2.16 at its plate's scale (its heights all read 2% under this view's)","via":"harvest"}},{"id":"tan","value":2.268,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/eotech-g45 6fece6de9f55 (eotechinc.com's gallery, EOTECH-G45-Tan-1: the tan kit's left side, in line, the riser fitted, 2049 px)","scaleRef":"eotech-g45.sts_mount_length along the mount's top plate (682 px: 410.5 px/in), which the diopter ring and the armour's height bear out against the black kit's picture (0.936 of it, each). Its whole height reads 3.36 in at that scale, 1.8% over the published one: a view from a little below","method":"the diopter ring's top and bottom rows 556 and 1176, their middle 866.5; the silhouette's bottom edge 1797.5: 931 px","via":"harvest"}}],"adopt":{"from":"left","reason":"The black kit's picture is the level one: its whole height reads the published 3.3 in at the scale the mount's length gives, and its two scales agree within 0.2%. The tan kit's has the magnifier 0.07 in higher over the same top plate and the kit 0.06 in taller than published: seen from a little below, where the outline's bottom is the far jaw's and the armour's parting line, 0.04 in under the ring's middle on the black picture, lies on it."},"note":"The axis is taken at the diopter ring's middle. The armoured body isn't centred on it: its top is 0.872 in above it and its underside 0.820 below, on all three side views (0.865 and 0.823 on Primary Arms', 0.867 and 0.812 on Rifle Supply's)."},"eyepiece_rear_behind_base":{"label":"The eyepiece's rear face behind the mount's centre","kind":"length","measurements":[{"id":"left","value":2.933,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/eotech-g45 64be77ba9788 (eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px)","scaleRef":"eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in)","method":"the diopter ring's rear edge at column 1864, the top plate's middle at 578 (its ends 214 and 942 over rows 1266 to 1338): 1286 px","via":"harvest"}}],"note":"Where the eye looks in: the eye relief runs back from here. The mount's centre is the middle of its top plate. The diopter ring turns, and stands where EOTECH pictured it."},"objective_front_ahead_of_base":{"label":"The objective's front face ahead of the mount's centre","kind":"length","measurements":[{"id":"left","value":0.819,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/eotech-g45 64be77ba9788 (eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px)","scaleRef":"eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in)","method":"the objective's front edge at column 219, the top plate's middle at 578: 359 px. The plate's own front end (214) stands 5 px ahead of it","via":"harvest"}}]},"objective_tube_od":{"label":"The objective tube's outside diameter","kind":"length","measurements":[{"id":"left","value":1.512,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/eotech-g45 64be77ba9788 (eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px)","scaleRef":"eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in)","method":"the tube's top edge at row 435 (columns 238 to 610), the axis at 766.5: 331.5 px, doubled","via":"harvest"}}],"note":"Its top edge above the axis, doubled: its underside is behind its foot in a side view. It comes to the diopter ring's diameter within a pixel, the two being about one axis."},"eyepiece_ring_od":{"label":"The diopter ring's outside diameter","kind":"length","measurements":[{"id":"left","value":1.512,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/eotech-g45 64be77ba9788 (eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px)","scaleRef":"eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in)","method":"rows 435 to 1097 over columns 1762 to 1846: 663 px","via":"harvest"}}]},"eyepiece_neck_od":{"label":"The neck between the armoured body and the diopter ring: its diameter","kind":"length","measurements":[{"id":"left","value":1.295,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/eotech-g45 64be77ba9788 (eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px)","scaleRef":"eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in)","method":"rows 483 to 1050 at columns 1714 to 1726: 568 px","via":"harvest"}}]},"body_top_above_axis":{"label":"The armoured body's top above the optical axis","kind":"length","measurements":[{"id":"left","value":0.872,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/eotech-g45 64be77ba9788 (eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px)","scaleRef":"eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in)","method":"the body's top edge at row 384 behind the knob (columns 1462 to 1654) and on the collar's top pad (658 to 1042), the axis at 766.5: 382.5 px","via":"harvest"}}]},"body_bottom_below_axis":{"label":"The armoured body's underside below the optical axis","kind":"length","measurements":[{"id":"left","value":0.82,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/eotech-g45 64be77ba9788 (eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px)","scaleRef":"eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in)","method":"the body's bottom edge at row 1126 (columns 1162 to 1654), the axis at 766.5: 359.5 px","via":"harvest"}}]},"body_side_flat_top_above_axis":{"label":"The armoured body's side flat: its upper edge above the optical axis","kind":"length","measurements":[{"id":"left","value":0.334,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/eotech-g45 64be77ba9788 (eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px)","scaleRef":"eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in)","method":"down columns 1380 to 1440 and 1520 to 1580, the picture's brightness: the lit upper facet (150 of 255) falls to the dark side flat (45) between rows 608 and 632, its middle at 620; the axis at 766.5: 146.5 px","via":"harvest"}},{"id":"tan","value":0.396,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/eotech-g45 6fece6de9f55 (eotechinc.com's gallery, EOTECH-G45-Tan-1: the tan kit's left side, in line, the riser fitted, 2049 px)","scaleRef":"eotech-g45.sts_mount_length along the mount's top plate (682 px: 410.5 px/in), which the diopter ring and the armour's height bear out against the black kit's picture (0.936 of it, each). Its whole height reads 3.36 in at that scale, 1.8% over the published one: a view from a little below","method":"down columns 1380 to 1440 and 1500 to 1560: the lit upper facet falls to the darker side flat between rows 700 and 708, its middle at 704; the diopter ring's middle at 866.5: 162.5 px","via":"harvest"}}],"adopt":{"from":"left","reason":"The black kit's picture is the level one (axis_above_clamp_bottom says why). The tan kit's has the same flat, 0.72 in tall, 0.055 in higher on the body: what faces the lens reads high in a view from below. Between the two the flat is about the axis; the model has the black picture's."},"note":"The body behind the collar is eight-sided: a flat on top (the knob stands on it), one underneath, one down each side, and a facet between each two. In the side view the upper facet is lit and the side flat dark; the edge between them is a soft one."},"body_side_flat_bottom_below_axis":{"label":"The armoured body's side flat: its lower edge below the optical axis","kind":"length","measurements":[{"id":"left","value":0.373,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/eotech-g45 64be77ba9788 (eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px)","scaleRef":"eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in)","method":"down the same columns: the dark side flat (47) gives way to the lower facet (75) between rows 924 and 936, its middle at 930; the axis at 766.5: 163.5 px","via":"harvest"}},{"id":"tan","value":0.325,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/eotech-g45 6fece6de9f55 (eotechinc.com's gallery, EOTECH-G45-Tan-1: the tan kit's left side, in line, the riser fitted, 2049 px)","scaleRef":"eotech-g45.sts_mount_length along the mount's top plate (682 px: 410.5 px/in), which the diopter ring and the armour's height bear out against the black kit's picture (0.936 of it, each). Its whole height reads 3.36 in at that scale, 1.8% over the published one: a view from a little below","method":"down the same columns: the side flat gives way to the lower facet between rows 996 and 1004, its middle at 1000; the diopter ring's middle at 866.5: 133.5 px","via":"harvest"}}],"adopt":{"from":"left","reason":"As its upper edge: the black kit's picture, the level one; the tan kit's has the edge 0.05 in higher."}},"body_half_width":{"label":"The armoured body's half width (its side flat out from the optical axis's vertical)","kind":"length","measurements":[{"id":"derived","value":0.8915,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"({.body_side_flat_top_above_axis} + {.body_side_flat_bottom_below_axis}) / 2 + {.body_top_above_axis} - {.body_side_flat_top_above_axis}","via":"harvest"}}],"note":"Worked out, not read: no view square across the magnifier is on file. The facets between the flats are taken at 45 degrees, so the body is as far out past its top flat's edge as the upper facet is tall in the side view (0.538 in); and the top flat is taken as wide as the side flats are tall (0.707 in), which the knob on it (0.675 in across) just fits. A regular eight-sided body of this height would be 0.846; wider than tall, then, by a tenth of an inch. With the tan kit's picture's reading of the flat's upper edge it would be 0.84: the ± covers it."},"body_height":{"label":"The armoured body, top to bottom","kind":"length","measurements":[{"id":"derived","value":1.692,"unit":"in","pm":0.014,"source":{"type":"derived","expr":"{.body_top_above_axis} + {.body_bottom_below_axis}","via":"harvest"}}]},"collar_pad_relief":{"label":"The collar's pads: how far they stand out of the collar","kind":"length","measurements":[{"id":"left","value":0.027,"unit":"in","pm":0.007,"source":{"type":"photo","photo":"references/eotech-g45 64be77ba9788 (eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px)","scaleRef":"eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in)","method":"the top pad's top at row 384 (columns 658 to 1042); the collar ahead of it at rows 395 and 391 (columns 634 and 646) and behind it at 396 and 397 (columns 1066 and 1078): 12 px","via":"harvest"}}],"note":"Read where the top pad meets the picture's outline: the armour's front end, a collar an inch long, has a raised pad on its top, one on each side and one between each two; ahead of the top pad and behind it the collar's own skin shows, lower."},"collar_pads":{"label":"The pads round the collar","kind":"count","measurements":[{"id":"views","value":7,"unit":"count","source":{"type":"photo","photo":"references/eotech-g45 64be77ba9788 (the left side), 4bcd30bff255 (the right side), 1401ce09b146 and 4c5adfd48657 (Primary Arms' G45.NM_01 and _03, from above), 8bf71db67f7a (T.REX ARMS' 8483, the underside)","scaleRef":"none needed: a count","method":"one on top, three on each side at the axis's height and 45 degrees above and below it, none underneath","via":"harvest"}}],"note":"Counted across the views, no one of which shows the whole turn: the top one in the outline of both side views and face on in Primary Arms' views from above (G45.NM_01, G45.NM_03); three down each side (EOTECH's left side view, Rifle Supply's right); none underneath, where the foot is (T.REX ARMS' picture of the parts laid out, 8483)."},"collar_pad_front_behind_base":{"label":"The collar's pads: their front ends behind the mount's centre","kind":"length","measurements":[{"id":"left","value":0.176,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/eotech-g45 64be77ba9788 (eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px)","scaleRef":"eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in)","method":"the top pad's front end in the outline at column 655 (the outline reaches row 384 at 658), and the upper side pad's lit front rim at 650 to 660 on row 475; the top plate's middle at 578: 77 px","via":"harvest"}}]},"collar_pad_length":{"label":"The collar's pads: their length along the housing","kind":"length","measurements":[{"id":"left","value":0.889,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/eotech-g45 64be77ba9788 (eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px)","scaleRef":"eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in)","method":"columns 655 to 1045 (the top pad in the outline; the upper side pad's lit rims on row 475): 390 px","via":"harvest"}}]},"collar_pad_angle":{"label":"The collar's pads down each side: how much of the turn each takes","kind":"angle","measurements":[{"id":"left","value":34,"unit":"deg","pm":3,"source":{"type":"photo","photo":"references/eotech-g45 64be77ba9788 (eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px)","scaleRef":"eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in)","method":"the pads' outlines on the picture, unwrapped about the armour's middle (row 755) at the pads' radius (371 px): the upper one from row 445 to 610 (57 and 23 degrees up: 34 wide), the one at the axis's height from 670 to 890 (220 px about its own middle: 34). On the tan kit's picture (rows 555 to 700, and 760 to 960, at 410.5 px/in) they read 34 and 34","via":"harvest"}}],"note":"The three down a side read alike on EOTECH's two left side views, the black kit's and the tan's: 33 to 35 degrees each."},"collar_top_pad_angle":{"label":"The collar's pad on top: how much of the turn it takes","kind":"angle","measurements":[{"id":"left","value":44,"unit":"deg","pm":5,"source":{"type":"photo","photo":"references/eotech-g45 64be77ba9788 (eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px)","scaleRef":"eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in)","method":"the top pad is seen edge on: its lower edge at row 413, unwrapped about the armour's middle (row 755) at the pads' radius (371 px): 67 degrees up, 23 short of the top each side. The tan kit's picture has it at 68","via":"harvest"}}]},"collar_panel_length":{"label":"The sunk panel in each pad above and below the axis's height: its length along the housing","kind":"length","measurements":[{"id":"left","value":0.787,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/eotech-g45 64be77ba9788 (eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px)","scaleRef":"eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in)","method":"the upper pad's panel, its two end walls at columns 675 and 1020: 345 px","via":"harvest"}}],"note":"The four pads 45 degrees above and below the axis's height have a panel sunk in their faces, a rim left round it; the pad on top and the two at the axis's height are plain (EOTECH's views from ahead, Midwest Gun Works' of the tan one)."},"collar_panel_angle":{"label":"The sunk panel in a pad: how much of the turn it takes","kind":"angle","measurements":[{"id":"left","value":22,"unit":"deg","pm":3,"source":{"type":"photo","photo":"references/eotech-g45 64be77ba9788 (eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px)","scaleRef":"eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in)","method":"the upper pad's panel from row 460 to 565, unwrapped about the armour's middle (row 755) at the pads' radius (371 px): 53 and 31 degrees up. The tan kit's picture reads 22 (rows 570 to 660)","via":"harvest"}}]},"collar_panel_depth":{"label":"The sunk panel in a pad: its depth","kind":"length","measurements":[{"id":"derived","value":0.027,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{.collar_pad_relief}","via":"harvest"}}],"note":"Not read to better than a factor of two. A side view shows the panel's two walls only as bands: 16 and 12 px tall on the tan kit's picture (410.5 px/in), 56 and 35 degrees up the collar, which is 0.047 and 0.051 in were the walls square to the face, and less as they are sloped. Taken as the pad's own relief, which those bracket from above: the panel's floor is then the collar's skin."},"top_knob_d":{"label":"The vertical adjustment's knob, across","kind":"length","measurements":[{"id":"left","value":0.675,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/eotech-g45 64be77ba9788 (eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px)","scaleRef":"eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in)","method":"columns 1165 to 1460 at rows 318 and 378: 296 px. Rifle Supply's right side view reads 0.674 (343 px)","via":"harvest"}}]},"top_knob_behind_base":{"label":"The vertical adjustment's knob: its axis behind the mount's centre","kind":"length","measurements":[{"id":"left","value":1.675,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/eotech-g45 64be77ba9788 (eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px)","scaleRef":"eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in)","method":"the knob's middle at column 1312.5, the top plate's at 578: 734.5 px","via":"harvest"}}]},"knob_lugs":{"label":"The lugs round each adjustment knob","kind":"count","measurements":[{"id":"right","value":8,"unit":"count","source":{"type":"photo","photo":"references/eotech-g45 4bcd30bff255 (Rifle Supply's EOG45STS_2_HR: the right side, in line, the riser fitted, 2000 px)","scaleRef":"eotech-g45.sts_mount_length along the mount's top plate (846 px: 509.2 px/in). What stands up the picture reads 2.3% under EOTECH's own view at that scale (the published height comes to 3.23 in on it), so lengths, a count and a knob seen face on are taken from it, and no height","method":"the knob marked R, face on in this view, unwrapped about its middle (column 692, row 698) into a strip of angle against radius: at radius 170 to 176 px eight lit lugs, their middles at 9, 51, 97, 142, 187, 232, 277 and 321 degrees, a dark notch between each two","via":"harvest"}}],"note":"Counted on the horizontal knob, the one view that shows a knob's whole turn; the vertical one is the same knob by the side views (two tiers of lugs, one over the other, with a groove between)."},"knob_notch_depth":{"label":"The notches between a knob's lugs: their depth","kind":"length","measurements":[{"id":"right","value":0.035,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/eotech-g45 4bcd30bff255 (Rifle Supply's EOG45STS_2_HR: the right side, in line, the riser fitted, 2000 px)","scaleRef":"eotech-g45.sts_mount_length along the mount's top plate (846 px: 509.2 px/in). What stands up the picture reads 2.3% under EOTECH's own view at that scale (the published height comes to 3.23 in on it), so lengths, a count and a knob seen face on are taken from it, and no height","method":"the knob marked R unwrapped about its middle (column 692, row 698): the lugs lit out to radius 179 px, the notches open down to 161","via":"harvest"}}]},"knob_notch_angle":{"label":"The notches between a knob's lugs: how much of the turn each takes","kind":"angle","measurements":[{"id":"right","value":24,"unit":"deg","pm":3,"source":{"type":"photo","photo":"references/eotech-g45 4bcd30bff255 (Rifle Supply's EOG45STS_2_HR: the right side, in line, the riser fitted, 2000 px)","scaleRef":"eotech-g45.sts_mount_length along the mount's top plate (846 px: 509.2 px/in). What stands up the picture reads 2.3% under EOTECH's own view at that scale (the published height comes to 3.23 in on it), so lengths, a count and a knob seen face on are taken from it, and no height","method":"the knob marked R unwrapped about its middle: at radius 170 px each lug 21 to 24 degrees of the 45 from one to the next, each notch the rest","via":"harvest"}}]},"knob_notch_phase":{"label":"Where the knob's notches stood in the picture","kind":"angle","measurements":[{"id":"right","value":30,"unit":"deg","pm":3,"source":{"type":"photo","photo":"references/eotech-g45 4bcd30bff255 (Rifle Supply's EOG45STS_2_HR: the right side, in line, the riser fitted, 2000 px)","scaleRef":"eotech-g45.sts_mount_length along the mount's top plate (846 px: 509.2 px/in). What stands up the picture reads 2.3% under EOTECH's own view at that scale (the published height comes to 3.23 in on it), so lengths, a count and a knob seen face on are taken from it, and no height","method":"the knob marked R unwrapped about its middle: the first notch's middle, from the direction of the muzzle toward the underside (between the lugs at 9 and 51 degrees)","via":"harvest"}}],"note":"A knob turns: this is only how it was set when photographed, taken so that the model is as pictured."},"side_knob_reach":{"label":"The horizontal adjustment's knob: its outer face right of the optical axis's vertical","kind":"length","measurements":[{"id":"derived","value":1.1227,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{.body_half_width} + {.height} - {.axis_above_clamp_bottom} - {.body_top_above_axis}","via":"harvest"}}],"note":"Worked out, not read: the knob on the body's right is taken to stand as far out of its side flat as the same knob stands out of its top (the kit's height, less the axis's height over the clamp's bottom and the body's top over the axis: 0.231 in)."},"diopter_flutes":{"label":"The flutes round the diopter ring","kind":"count","measurements":[{"id":"sides","value":20,"unit":"count","pm":1,"source":{"type":"photo","photo":"references/eotech-g45 64be77ba9788 (EOTECH's left side view) and 4bcd30bff255 (Rifle Supply's right side view)","scaleRef":"none needed: angles about the ring's own axis, by its own radius in each picture","method":"the ring's brightness down its length, unwrapped about its middle (row 766.5, radius 331 px on the left view; 719 and 379 on the right): dark edges at 75, 57, 40 and 22 degrees above the axis and 22, 40, 58 below it on the left view; 59, 42, 23 and 6 above and 21, 39, 56 below on the right","via":"harvest"}}],"note":"Not a count of the whole turn: no view from behind is on file. The flutes' shadowed edges, unwrapped about the ring's axis on two side views, are 17.5 to 18 degrees apart over the 100 degrees of the ring each view reads well, which is 20 round the ring; 19 or 21 isn't excluded."},"diopter_flute_angle":{"label":"The diopter ring's flutes: how much of the turn each takes","kind":"angle","measurements":[{"id":"left","value":8,"unit":"deg","pm":3,"source":{"type":"photo","photo":"references/eotech-g45 64be77ba9788 (eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px)","scaleRef":"eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in)","method":"the ring unwrapped about its middle: the flutes' dark edges are a whole number of pitches apart on either side of the axis and 44 degrees across it, two pitches and a flute's width; each dark run 4 to 5 degrees","via":"harvest"}}]},"diopter_flute_depth":{"label":"The diopter ring's flutes: their depth","kind":"length","measurements":[{"id":"g33","value":0.028,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{eotech-g33.diopter_flute_depth}","via":"harvest"}}],"note":"Not read on this ring: no flute stands at the outline in any view on file. Taken as the G33's ring's, a like ring, so that the flutes can be drawn at all; said in the part's approximations."},"eyepiece_glass_d":{"label":"The eyepiece's glass, visible diameter","kind":"length","measurements":[{"id":"oblique","value":0.92,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/eotech-g45 461e2e14e1e4 (Primary Arms' G45.STS_03: from behind and the left, above)","scaleRef":"eotech-g45.eyepiece_ring_od: the ring's rear rim and the glass are two circles about one axis, a few tenths of an inch apart in depth, and each one's longest diameter in an oblique view is its own","method":"the ring's rear rim 642 px on its long axis (rows 260 to 902), the glass 390 (rows 390 to 775): 0.61 of the ring. The glass lies deeper than the rim and reads a little small","via":"harvest"}}]},"objective_glass_d":{"label":"The objective's clear aperture","kind":"length","measurements":[{"id":"kygunco","value":25,"unit":"mm","stated":"Objective 25","source":{"type":"spec","publisher":"retailer","name":"KYGunCo, EOTech G45 5X QD Magnifier Tan (G45.STSTAN)","url":"https://www.kygunco.com/product/eotech-g45.ststan-5-power-magnifer-with-qd-sts-mount-tan","retrieved":"2026-10-12","via":"harvest"},"note":"The seller's own row, its unit not stated: millimetres, as such a row is. The same table says \"Size 34mm\"."},{"id":"oblique","value":1.02,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/eotech-g45 76ef6ba38226 (Rifle Supply's EOG45STS_1_HR: from ahead and the left, above)","scaleRef":"eotech-g45.objective_tube_od: the tube's front rim and the glass are two circles about one axis, and each one's longest diameter in an oblique view is its own","method":"the tube's front rim 665 px on its long axis (rows 545 to 1210), the glass that shows 450 (rows 630 to 1080): 0.68 of the tube","via":"harvest"}}],"adopt":{"from":"kygunco","reason":"A stated figure, and the picture reads within 0.04 in of it; one seller, its unit not stated: provisional."},"note":"EOTECH states neither it nor an exit pupil. One seller's table has a row \"Objective 25\" with no unit; the glass that shows in a view from ahead is 0.68 of the tube across."},"sts_mount_length":{"label":"The STS mount's length (its top plate)","kind":"length","measurements":[{"id":"g33","value":1.6614,"unit":"in","source":{"type":"derived","expr":"{eotech-g33.sts_mount_length}","via":"harvest"},"note":"The same mount: EOTECH's page for the STS mount alone (9-G33STS) says \"This is the standard mount that comes with the G33, G43 and G45.\" Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger."}]},"sts_mount_height":{"label":"The STS mount's height (the clamp's bottom to the hinge knuckles' top)","kind":"length","measurements":[{"id":"g33","value":1.1811,"unit":"in","source":{"type":"derived","expr":"{eotech-g33.sts_mount_height}","via":"harvest"},"note":"The same mount: EOTECH's page for the STS mount alone (9-G33STS) says \"This is the standard mount that comes with the G33, G43 and G45.\" Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger."}]},"clamp_below_rail":{"label":"The clamp's bottom below the rail's top","kind":"length","measurements":[{"id":"g33","value":0.37,"unit":"in","pm":0.035,"source":{"type":"derived","expr":"{eotech-g33.clamp_below_rail}","via":"harvest"},"note":"The same mount: EOTECH's page for the STS mount alone (9-G33STS) says \"This is the standard mount that comes with the G33, G43 and G45.\" Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger."}]},"clamp_bottom_y":{"label":"The clamp's bottom in the part frame (y; the rail's top is 0)","kind":"length","measurements":[{"id":"derived","value":-0.37,"unit":"in","pm":0.035,"source":{"type":"derived","expr":"-{.clamp_below_rail}","via":"harvest"},"note":"Where the side profile's origin (the clamp's bottom) sits in the part frame."}]},"riser_top_above_clamp_bottom":{"label":"The riser's top (the magnifier's foot's underside) above the clamp's bottom","kind":"length","measurements":[{"id":"g33","value":1.385,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{eotech-g33.riser_top_above_clamp_bottom}","via":"harvest"},"note":"The same mount: EOTECH's page for the STS mount alone (9-G33STS) says \"This is the standard mount that comes with the G33, G43 and G45.\" Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger."}]},"plate_top_above_clamp_bottom":{"label":"The mount's top plate: its top above the clamp's bottom","kind":"length","measurements":[{"id":"g33","value":1.1,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{eotech-g33.plate_top_above_clamp_bottom}","via":"harvest"},"note":"The same mount: EOTECH's page for the STS mount alone (9-G33STS) says \"This is the standard mount that comes with the G33, G43 and G45.\" Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger."}]},"plate_bottom_above_clamp_bottom":{"label":"The mount's top plate: its underside above the clamp's bottom","kind":"length","measurements":[{"id":"g33","value":0.866,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{eotech-g33.plate_bottom_above_clamp_bottom}","via":"harvest"},"note":"The same mount: EOTECH's page for the STS mount alone (9-G33STS) says \"This is the standard mount that comes with the G33, G43 and G45.\" Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger."}]},"riser_length":{"label":"The riser's length along the rail","kind":"length","measurements":[{"id":"g33","value":1.608,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{eotech-g33.riser_length}","via":"harvest"},"note":"The same mount: EOTECH's page for the STS mount alone (9-G33STS) says \"This is the standard mount that comes with the G33, G43 and G45.\" Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger."},{"id":"left","value":1.612,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/eotech-g45 64be77ba9788 (eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px)","scaleRef":"eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in)","method":"columns 223 to 929 over rows 1134 to 1230: 707 px","via":"harvest"}}],"adopt":{"from":"g33","reason":"The same riser; this picture reads it 0.004 in longer, inside both ±."}},"riser_width":{"label":"The riser's width across the rail","kind":"length","measurements":[{"id":"g33","value":0.75,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{eotech-g33.riser_width}","via":"harvest"},"note":"The same mount: EOTECH's page for the STS mount alone (9-G33STS) says \"This is the standard mount that comes with the G33, G43 and G45.\" Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger."}]},"plate_width":{"label":"The mount's top plate: its width across the rail, without the arm to the hinge","kind":"length","measurements":[{"id":"g33","value":0.64,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{eotech-g33.plate_width}","via":"harvest"},"note":"The same mount: EOTECH's page for the STS mount alone (9-G33STS) says \"This is the standard mount that comes with the G33, G43 and G45.\" Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger."}]},"base_top_above_clamp_bottom":{"label":"The clamp base's top (the lever's top edge) above the clamp's bottom","kind":"length","measurements":[{"id":"g33","value":0.555,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{eotech-g33.base_top_above_clamp_bottom}","via":"harvest"},"note":"The same mount: EOTECH's page for the STS mount alone (9-G33STS) says \"This is the standard mount that comes with the G33, G43 and G45.\" Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger."}]},"clamp_length":{"label":"The clamp's length along the rail","kind":"length","measurements":[{"id":"g33","value":1.395,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{eotech-g33.clamp_length}","via":"harvest"},"note":"The same mount: EOTECH's page for the STS mount alone (9-G33STS) says \"This is the standard mount that comes with the G33, G43 and G45.\" Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger."},{"id":"left","value":1.418,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/eotech-g45 64be77ba9788 (eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px)","scaleRef":"eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in)","method":"the silhouette's lowest rows (1710 to 1722), columns 268 to 890: 622 px","via":"harvest"}}],"adopt":{"from":"g33","reason":"The same mount, read on a picture with two published lengths in it. This picture's bottom edge reads 0.023 in more, 1.6%: the lever's foot shows at its ends here."}},"lever_tail_behind_base":{"label":"The quick-detach lever's tail end, behind the mount's centre (closed)","kind":"length","measurements":[{"id":"left","value":1.318,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/eotech-g45 64be77ba9788 (eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px)","scaleRef":"eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in)","method":"the lever's tail end at column 1156 (rows 1482 to 1690), the top plate's middle at 578: 578 px","via":"harvest"}},{"id":"g33","value":1.381,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{eotech-g33.lever_tail_behind_base}","via":"harvest"},"note":"The same mount: EOTECH's page for the STS mount alone (9-G33STS) says \"This is the standard mount that comes with the G33, G43 and G45.\" Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger."}],"adopt":{"from":"left","reason":"The model's lever is this picture's outline. EOTECH's picture of the G33 on the same mount has the tail 0.06 in further back: the lever itself is 3.7% longer there against the plate, the riser and the base, which keep one scale between the two pictures. Which of the two is the mount's isn't known."},"note":"The lever is on the rifle's left and lies along the clamp, its tail to the rear."},"lever_bottom_above_clamp_bottom":{"label":"The quick-detach lever's underside above the clamp's bottom","kind":"length","measurements":[{"id":"g33","value":0.085,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{eotech-g33.lever_bottom_above_clamp_bottom}","via":"harvest"},"note":"The same mount: EOTECH's page for the STS mount alone (9-G33STS) says \"This is the standard mount that comes with the G33, G43 and G45.\" Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger."}]},"lever_thickness":{"label":"The quick-detach lever's thickness across the rail","kind":"length","measurements":[{"id":"g33","value":0.2,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{eotech-g33.lever_thickness}","via":"harvest"},"note":"The same mount: EOTECH's page for the STS mount alone (9-G33STS) says \"This is the standard mount that comes with the G33, G43 and G45.\" Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger."}]},"base_left_of_centre":{"label":"The clamp's left face (the lever's outer face), left of the rail's centre","kind":"length","measurements":[{"id":"g33","value":1,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{eotech-g33.base_left_of_centre}","via":"harvest"},"note":"The same mount: EOTECH's page for the STS mount alone (9-G33STS) says \"This is the standard mount that comes with the G33, G43 and G45.\" Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger."}]},"hinge_axis_above_clamp_bottom":{"label":"The mount's hinge axis above the clamp's bottom","kind":"length","measurements":[{"id":"g33","value":0.871,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{eotech-g33.hinge_axis_above_clamp_bottom}","via":"harvest"},"note":"The same mount: EOTECH's page for the STS mount alone (9-G33STS) says \"This is the standard mount that comes with the G33, G43 and G45.\" Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger."}]},"hinge_axis_right_of_centre":{"label":"The mount's hinge axis to the right of the rail's centre","kind":"length","measurements":[{"id":"g33","value":0.69,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{eotech-g33.hinge_axis_right_of_centre}","via":"harvest"},"note":"The same mount: EOTECH's page for the STS mount alone (9-G33STS) says \"This is the standard mount that comes with the G33, G43 and G45.\" Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger."}],"note":"On the rifle's right as EOTECH pictures the G45 too: its left side view has the lever toward the lens, and Rifle Supply's right side view the hinge, with the knob marked R."},"hinge_pin_d":{"label":"The hinge pin's diameter","kind":"length","measurements":[{"id":"g33","value":0.316,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{eotech-g33.hinge_pin_d}","via":"harvest"},"note":"The same mount: EOTECH's page for the STS mount alone (9-G33STS) says \"This is the standard mount that comes with the G33, G43 and G45.\" Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger."}]},"hinge_knuckle_d":{"label":"The hinge knuckles' outside diameter","kind":"length","measurements":[{"id":"g33","value":0.62,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{eotech-g33.hinge_knuckle_d}","via":"harvest"},"note":"The same mount: EOTECH's page for the STS mount alone (9-G33STS) says \"This is the standard mount that comes with the G33, G43 and G45.\" Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger."}]},"hinge_block_length":{"label":"The hinge's length along the rail (both knuckles and the barrel between them)","kind":"length","measurements":[{"id":"g33","value":1.394,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{eotech-g33.hinge_block_length}","via":"harvest"},"note":"The same mount: EOTECH's page for the STS mount alone (9-G33STS) says \"This is the standard mount that comes with the G33, G43 and G45.\" Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger."},{"id":"right","value":1.416,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/eotech-g45 4bcd30bff255 (Rifle Supply's EOG45STS_2_HR: the right side, in line, the riser fitted, 2000 px)","scaleRef":"eotech-g45.sts_mount_length along the mount's top plate (846 px: 509.2 px/in). What stands up the picture reads 2.3% under EOTECH's own view at that scale (the published height comes to 3.23 in on it), so lengths, a count and a knob seen face on are taken from it, and no height","method":"columns 1203 to 1924 over rows 1386 to 1498 (the rear knuckle's rear face to the front one's front): 721 px","via":"harvest"}}],"adopt":{"from":"g33","reason":"The same mount, read on EOTECH's own right side view of it; Rifle Supply's picture reads 0.02 in more at its plate's scale, 1.6%."}},"hinge_knuckle_length":{"label":"Each hinge knuckle's length along the rail","kind":"length","measurements":[{"id":"g33","value":0.37,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{eotech-g33.hinge_knuckle_length}","via":"harvest"},"note":"The same mount: EOTECH's page for the STS mount alone (9-G33STS) says \"This is the standard mount that comes with the G33, G43 and G45.\" Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger."}]},"hinge_web_inner_right_of_centre":{"label":"The wall under the hinge: its inner face right of the rail's centre","kind":"length","measurements":[{"id":"g33","value":0.13,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{eotech-g33.hinge_web_inner_right_of_centre}","via":"harvest"},"note":"The same mount: EOTECH's page for the STS mount alone (9-G33STS) says \"This is the standard mount that comes with the G33, G43 and G45.\" Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger."}]},"hinge_barrel_d":{"label":"The hinge barrel's diameter (the plate's arm, between the knuckles)","kind":"length","measurements":[{"id":"g33","value":0.5,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{eotech-g33.hinge_barrel_d}","via":"harvest"},"note":"The same mount: EOTECH's page for the STS mount alone (9-G33STS) says \"This is the standard mount that comes with the G33, G43 and G45.\" Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger."}]},"clamp_nut_d":{"label":"The clamp's adjustment nut on the mount's right face, across","kind":"length","measurements":[{"id":"g33","value":0.36,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{eotech-g33.clamp_nut_d}","via":"harvest"},"note":"The same mount: EOTECH's page for the STS mount alone (9-G33STS) says \"This is the standard mount that comes with the G33, G43 and G45.\" Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger."}]},"clamp_nut_above_clamp_bottom":{"label":"The clamp's adjustment nut: its axis above the clamp's bottom","kind":"length","measurements":[{"id":"g33","value":0.32,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{eotech-g33.clamp_nut_above_clamp_bottom}","via":"harvest"},"note":"The same mount: EOTECH's page for the STS mount alone (9-G33STS) says \"This is the standard mount that comes with the G33, G43 and G45.\" Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger."}]},"flip_angle":{"label":"How far the magnifier swings to the side on its mount","kind":"angle","measurements":[{"id":"g33","value":93.5,"unit":"deg","pm":3,"source":{"type":"derived","expr":"{eotech-g33.flip_angle}","via":"harvest"},"note":"The same mount: EOTECH's page for the STS mount alone (9-G33STS) says \"This is the standard mount that comes with the G33, G43 and G45.\" Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger."}],"note":"To the rifle's right as EOTECH pictures it. No page states the angle, and no pair of views of the G45 from behind is on file: it is the same mount's, read between EOTECH's two rear views of the G33 on it."}}},{"subject":"expo-arms-mlok-15-handguard","title":"Expo Arms Free Float AR-15 Handguard - M-LOK - 15\" (XP-GUARD15-BLK)","dimensions":{"weight":{"label":"Weight (whether with its barrel nut isn't said)","kind":"mass","measurements":[{"id":"pa","value":13.2,"unit":"oz","pm":0.05,"stated":"Weight 13.2 oz.","source":{"type":"spec","publisher":"manufacturer","name":"Primary Arms (Expo Arms is its house brand), Expo Arms Free Float AR-15 Handguard - M-LOK - 15\" (XP-GUARD15-BLK), Specifications; its Features say \"13.2 oz weight\"","url":"https://www.primaryarms.com/expo-arms-m-lok-handguard-black-15","retrieved":"2026-10-05","via":"harvest"}},{"id":"pa-fde","value":18.2,"unit":"oz","pm":0.05,"stated":"18.2 oz weight","source":{"type":"spec","publisher":"manufacturer","name":"Primary Arms, Expo Arms Free Float AR-15 Handguard - M-LOK - 15\" - FDE (XP-GUARD15-FDE), Features: the same handguard in FDE Cerakote; its Specifications have no weight row","url":"https://www.primaryarms.com/expo-arms-15-m-lok-handguard-flat-dark-earth-xp-guard15-fde","retrieved":"2026-10-05","via":"harvest"}},{"id":"buyer","value":13,"unit":"oz","pm":0.5,"stated":"After I ordered it I saw they said it weights 18 oz. I'm glad to report that it's only 13 oz.","source":{"type":"spec","publisher":"review","name":"A buyer's review on Primary Arms' page for XP-GUARD15-BLK (Michael, 2/10/2023, \"Only 13 ounces\"): no method given","url":"https://www.primaryarms.com/expo-arms-m-lok-handguard-black-15","retrieved":"2026-10-05","via":"harvest"}}],"adopt":{"from":"pa","reason":"This handguard's own page, in two places, and a buyer says his is 13 oz; the FDE page's 18.2 oz is the figure that buyer says this page once carried."},"note":"Three figures, and no page says what was weighed: the black handguard's own page says 13.2 oz twice (its features and its specifications), the page for the same handguard in FDE Cerakote says 18.2 oz, and a buyer on the black page says the page used to say 18 oz and that his is 13. The handguard \"comes with a 6061-T6 aluminum barrel nut\": 5 oz is more than such a nut and three bolts weigh, so the difference isn't explained by it. Kept visible. What the model holds (its section, bored round, its slots cut) is 8.8 cubic inches, 13.8 oz as 6061 (std.density.aluminium), and the real one has flats inside where the model's bore is round: that points to 13.2 oz being the handguard's own, without its nut."},"length":{"label":"Length (its rear face to its front face; the two tabs reach 0.19 in further back)","kind":"length","measurements":[{"id":"pa","value":15,"unit":"in","pm":0.5,"stated":"Handguard Length 15","source":{"type":"spec","publisher":"manufacturer","name":"Primary Arms, Expo Arms Free Float AR-15 Handguard - M-LOK - 15\" (XP-GUARD15-BLK), Specifications; its Features say '15\" length'","url":"https://www.primaryarms.com/expo-arms-m-lok-handguard-black-15","retrieved":"2026-10-05","via":"harvest"}},{"id":"photo-right","value":14.99,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard b0ebc4d7c105 (Primary Arms' gallery for XP-GUARD15-BLK, photo _01: the handguard's right side on white, the receiver's end at the left, 2200 x 1467)","scaleRef":"its own top rail: the 35 teeth between its end lands, one Picatinny pitch apart (std.picatinny.slot_pitch), fitted along the photo (127.6 px/in at the rear end, 129.6 in the middle, 125.6 at the front; rms 0.0006 in)","method":"the silhouette's ends on the rows of the side face, 0.911 behind the rearmost tooth's centre and 14.276 ahead of it as the teeth read them; they are the side face's edges, 0.44 in nearer the lens than the teeth's near sides, and the lens is 33.2 in away with its foot 7.04 in ahead of the rear face: 0.815 and 14.168, 14.985 apart. The rail's own ends on its rows read the same faces (0.824 behind, 14.16 ahead) (.cache/batch123/expo-arms-mlok-15-handguard/meas5.py)","via":"harvest"}},{"id":"photo-left","value":14.99,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard c3d5763fef0d (Primary Arms' gallery for XP-GUARD15-BLK, photo _02: its left side on white, the receiver's end at the right, 2200 x 1467)","scaleRef":"its own top rail's 35 teeth at the Picatinny pitch (std.picatinny.slot_pitch), fitted along the photo (rms 0.0006 in)","method":"as the right side's, the lens 35.3 in away: the front face 0.773 ahead of the foremost tooth's centre, the rear face 14.220 behind it: 14.993","via":"harvest"}}],"adopt":{"from":"pa","reason":"The maker's figure. Both side photos, read along the rail's own teeth, put its rear face 14.99 in from its front face: the 15 is the body's, without the two tabs."}},"width":{"label":"Width across its side flats (the 3 and 9 o'clock faces)","kind":"length","measurements":[{"id":"photo-right","value":1.59,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard b0ebc4d7c105 (Primary Arms' gallery for XP-GUARD15-BLK, photo _01: the handguard's right side on white, the receiver's end at the left, 2200 x 1467)","scaleRef":"the lens's distance from the rail's own width: read along the rail's teeth at each height below their tops, the middle windows' near and far ends put the plane of the teeth's near sides 0.0099 to 0.0127 of the lens's distance off the rail's middle, growing by 0.0309 per inch of depth (a 45.7 degree bevel) and levelling off at 0.01258 where the rail is widest: .835 / 2 (std.picatinny.top_width) over 0.01258 is 33.2 in","method":"eight windows, each end at the 50% level, fitted with the slots 40 mm apart (std.mlok.slot_pitch): near ends spread by 1.01343, far ones drawn in by 0.96601 (rms 0.0009 in; the same to 0.00004 along the teeth at twelve heights): the walls 0.02395 of the lens's distance either side of the middle, 0.795 in. The lens's foot comes out at the same place from the windows (6.226 in ahead of the rearmost tooth) and from the teeth's end faces (6.218). ± is the lens's distance (the widest row is one pixel deep) and the left side's reading (.cache/batch123/expo-arms-mlok-15-handguard/cam3.py)","via":"harvest"}},{"id":"photo-left","value":1.63,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard c3d5763fef0d (Primary Arms' gallery for XP-GUARD15-BLK, photo _02: its left side on white, the receiver's end at the right, 2200 x 1467)","scaleRef":"as the right side's: the teeth's near sides 0.0095 to 0.0119 of the lens's distance off the middle, by 0.0293 per inch of depth (45.9 degrees), level at 0.01182 over three rows: 35.3 in","method":"as the right side's: near ends spread by 1.01315, far ones drawn in by 0.96754 (rms 0.0008 in): the walls 0.02303 of the lens's distance off the middle, 0.813 in","via":"harvest"}}],"adopt":{"from":"photo-right","reason":"The photo the outline is traced from; the other side's reading agrees within what either carries, and the faces' edges and the bottom's depth say the same octagon."},"note":"Not published, and no view down its length is on file. Read from each side photo by itself: a window in the middle row shows white where a ray passes the near wall's slot and the far wall's, so one end of each window is a slot's end on the near wall and the other on the far wall. Read along the rail's teeth the near ends are spread about the lens's foot by (D - rail) / (D - wall) and the far ones drawn in by (D - rail) / (D + wall): the two walls' distance over the lens's. Two other readings say the same: the edge between a side flat and a diagonal face stands 0.29 from the bore's level (side_flat_half_height), which with the diagonals 0.775 out puts the flats 0.81 out; and the bottom and the diagonals stand 0.76 to 0.78 out. It is close to a regular octagon, a little wider than it is deep."},"height":{"label":"Height (its rail's top to its bottom flat; the clamp's block hangs 0.37 in below)","kind":"length","measurements":[{"id":"photo-right","value":1.96,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard b0ebc4d7c105 (Primary Arms' gallery for XP-GUARD15-BLK, photo _01: the handguard's right side on white, the receiver's end at the left, 2200 x 1467)","scaleRef":"its own rail's pitch at the photo's middle (std.picatinny.slot_pitch): 50.90 px a tooth, 129.2 px/in in the rail's mid-plane","method":"the photo levelled by its three rows of windows (1.121 degrees); the webs' brightness steps from white at the tooth tops (row 597.60) and to white at the bottom (row 853.36) 255.8 px apart: 1.980 in, less 0.02 for the bottom flat's near edge (.cache/batch123/expo-arms-mlok-15-handguard/facets.py)","via":"harvest"}},{"id":"photo-left","value":1.97,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard c3d5763fef0d (Primary Arms' gallery for XP-GUARD15-BLK, photo _02: its left side on white, the receiver's end at the right, 2200 x 1467)","scaleRef":"its own rail's pitch at the photo's middle: 50.69 px a tooth, 128.6 px/in","method":"as the right side's (levelled by 0.754 degrees): rows 582.88 and 839.08, 256.2 px, 1.992 in, less 0.02","via":"harvest"}}],"adopt":{"from":"photo-right","reason":"The photo the outline is traced from; the other side reads 0.01 more, within either's ±."},"note":"Not published. A side view's silhouette is the near edge of the bottom flat, which a lens 33 in away and an inch or so above the bore reads 0.02 in low (0.03 if the lens stood two inches above it: its height isn't pinned): taken off."},"inside_diameter":{"label":"Inside diameter","kind":"length","measurements":[{"id":"pa","value":1.35,"unit":"in","pm":0.005,"stated":"Inner Diameter 1.35 in.","source":{"type":"spec","publisher":"manufacturer","name":"Primary Arms, Expo Arms Free Float AR-15 Handguard - M-LOK - 15\" (XP-GUARD15-BLK), Specifications","url":"https://www.primaryarms.com/expo-arms-m-lok-handguard-black-15","retrieved":"2026-10-05","via":"harvest"}}],"note":"The page's figure, drawn as a round bore. Inside the faces the photos give, it leaves walls 0.085 to 0.12 in thick at the slots, which is what shows in the diagonal rows' slots (wall_at_slots). The three-quarter photos show flats inside behind the rows and ribs between them: not measured."},"rear_face_x":{"label":"Its rear face against the receiver's front face (negative: behind it)","kind":"length","measurements":[{"id":"shoulder","value":-0.445,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"0in - {std.ar15.upper_barrel_thread_length}","via":"harvest"}}],"note":"No photo of it mounted is on file, and Primary Arms publishes no instructions for it. Taken to seat against the receiver's front shoulder, where the barrel-nut thread begins (std.ar15.upper_barrel_thread_length: \"A barrel nut and a free-float handguard's rear end come back to that shoulder\"). A buyer on its page says it is made to: \"the hand-guard did not sit flush with the upper receiver, so the locking key did not sit into the groove of the barrel nut as intended ... I filed the dust cover pin down. That allowed the handguard to sit flush and for the locking key to fully seat in the barrel nut\" (Pikamon, 2/26/2025, https://www.primaryarms.com/expo-arms-m-lok-handguard-black-15). A buyer's words, not the maker's."},"tab_length":{"label":"Its two anti-rotation tabs: how far they reach behind its rear face","kind":"length","measurements":[{"id":"photo-right","value":0.19,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard b0ebc4d7c105 (Primary Arms' gallery for XP-GUARD15-BLK, photo _01: the handguard's right side on white, the receiver's end at the left, 2200 x 1467)","scaleRef":"its own top rail's 35 teeth at the Picatinny pitch (std.picatinny.slot_pitch), fitted along the photo; the lens 33.2 in away","method":"the tab's tip 1.031 behind the rearmost tooth's centre as the teeth read it, 1.010 at its own depth (taken 0.45 in off the middle): 0.195 behind the rear face at 0.815","via":"harvest"}},{"id":"photo-left","value":0.19,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard c3d5763fef0d (Primary Arms' gallery for XP-GUARD15-BLK, photo _02: its left side on white, the receiver's end at the right, 2200 x 1467)","scaleRef":"its own top rail's 35 teeth at the Picatinny pitch, fitted along the photo; the lens 35.3 in away","method":"the other tab, as the right side's: 0.193 behind the rear face","via":"harvest"}}],"adopt":{"from":"photo-right","reason":"The two tabs read the same; the right side's photo is the one traced."},"note":"Primary Arms: \"anti-rotation tabs for a strong lock-up on any Mil-Spec receiver\". One shows on each side photo, just under the rail's neck: its top edge level, its end square, its underside sloped up to the end (tab_top_above_bore and the two below it)."},"tab_top_above_bore":{"label":"A tab's top edge above the bore axis","kind":"length","measurements":[{"id":"photo","value":0.71,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard b0ebc4d7c105 and c3d5763fef0d (Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467)","scaleRef":"each photo's own rail pitch at its middle (std.picatinny.slot_pitch): 129.2 and 128.6 px/in; the bore's level its middle row of windows","method":"the silhouette's rear end row by row on the levelled photos: it steps back to the tab's end between 0.721 and 0.698 in above the middle row on the right side, 0.728 and 0.705 on the left","via":"harvest"}}]},"tab_tip_bottom_above_bore":{"label":"A tab's end, its lower corner above the bore axis","kind":"length","measurements":[{"id":"photo","value":0.56,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard b0ebc4d7c105 and c3d5763fef0d (Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467)","scaleRef":"each photo's own rail pitch at its middle (std.picatinny.slot_pitch): 129.2 and 128.6 px/in; the bore's level its middle row of windows","method":"the tab's end is square down to 0.559 in above the middle row on the right side, 0.565 on the left; below that its underside slopes forward","via":"harvest"}}]},"tab_root_bottom_above_bore":{"label":"A tab's underside where it meets the rear face, above the bore axis","kind":"length","measurements":[{"id":"photo","value":0.47,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard b0ebc4d7c105 and c3d5763fef0d (Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467)","scaleRef":"each photo's own rail pitch at its middle (std.picatinny.slot_pitch): 129.2 and 128.6 px/in; the bore's level its middle row of windows","method":"the sloped underside runs into the rear end's own edge 0.466 in above the middle row on the right side, 0.472 on the left","via":"harvest"}}]},"rear_x":{"label":"The outline's rear end (its two tabs' ends) against the receiver's front face (negative: behind it)","kind":"length","measurements":[{"id":"derived","value":-0.635,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.rear_face_x} - {.tab_length}","via":"harvest"}}]},"overall_length":{"label":"Overall length, the tabs' ends to the front face","kind":"length","measurements":[{"id":"photo-right","value":15.18,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard b0ebc4d7c105 (Primary Arms' gallery for XP-GUARD15-BLK, photo _01: the handguard's right side on white, the receiver's end at the left, 2200 x 1467)","scaleRef":"its own top rail's 35 teeth at the Picatinny pitch (std.picatinny.slot_pitch), fitted along the photo; the lens 33.2 in away","method":"the tab's tip 1.010 behind the rearmost tooth's centre and the front face 14.168 ahead of it, each at its own depth: 15.178","via":"harvest"}},{"id":"photo-left","value":15.19,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard c3d5763fef0d (Primary Arms' gallery for XP-GUARD15-BLK, photo _02: its left side on white, the receiver's end at the right, 2200 x 1467)","scaleRef":"its own top rail's 35 teeth at the Picatinny pitch, fitted along the photo; the lens 35.3 in away","method":"as the right side's: 15.186","via":"harvest"}}],"adopt":{"from":"photo-right","reason":"The photo the outline is traced from; the other side reads 0.01 more."}},"rail_top_above_bore":{"label":"Its rail's top above the bore axis","kind":"length","measurements":[{"id":"photo-right","value":1.2,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard b0ebc4d7c105 (Primary Arms' gallery for XP-GUARD15-BLK, photo _01: the handguard's right side on white, the receiver's end at the left, 2200 x 1467)","scaleRef":"its own rail's pitch at the photo's middle (std.picatinny.slot_pitch): 129.2 px/in in the rail's mid-plane","method":"the middle row's eight windows' centres (row 752.17; each window's top and bottom at the 50% level, on the levelled photo) 154.6 px below the step at the tooth tops (row 597.60): 1.197 in","via":"harvest"}},{"id":"photo-left","value":1.2,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard c3d5763fef0d (Primary Arms' gallery for XP-GUARD15-BLK, photo _02: its left side on white, the receiver's end at the right, 2200 x 1467)","scaleRef":"its own rail's pitch at the photo's middle: 128.6 px/in","method":"as the right side's: rows 737.67 and 582.88, 154.8 px, 1.203 in","via":"harvest"}}],"adopt":{"from":"photo-right","reason":"Both sides read 1.20."},"note":"The bore's level is taken as its middle row of M-LOK slots' (its 3 and 9 o'clock faces): the photos have no bore in them. A mil-spec flat-top receiver's rail stands the same height above its bore (Aero's M4E1 Threaded upper, from its own photos: 2.09 above the pins less the bore's .8775 is 1.2125), so with the handguard about the bore the two rails are level. No page on file says that they are."},"bottom_below_bore":{"label":"Its bottom flat below the bore axis","kind":"length","measurements":[{"id":"derived","value":0.76,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.height} - {.rail_top_above_bore}","via":"harvest"}}]},"diagonal_face_distance":{"label":"Its four diagonal faces: how far each stands from the bore axis","kind":"length","measurements":[{"id":"photo-right","value":0.775,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard b0ebc4d7c105 (Primary Arms' gallery for XP-GUARD15-BLK, photo _01: the handguard's right side on white, the receiver's end at the left, 2200 x 1467)","scaleRef":"its own rail's pitch at the photo's middle (std.picatinny.slot_pitch): 129.2 px/in in the rail's mid-plane","method":"the upper and lower rows' windows' centres 0.504 in above and 0.510 below the middle row's (rows 687.02, 752.17 and 818.02 on the levelled photo): 0.507 either side. A slot through a wall standing at 45 degrees shows open only where the ray clears both of the wall's faces, so each window's centre is nearer the bore's level than its slot's by 0.354 of the wall's thickness (0.11, wall_at_slots): the slots 0.547 off the bore's level, and on the 45 degree lines that is 0.774 from the axis","via":"harvest"}},{"id":"photo-left","value":0.778,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard c3d5763fef0d (Primary Arms' gallery for XP-GUARD15-BLK, photo _02: its left side on white, the receiver's end at the right, 2200 x 1467)","scaleRef":"its own rail's pitch at the photo's middle: 128.6 px/in","method":"as the right side's: 0.507 above and 0.512 below the middle row's (rows 672.46, 737.67 and 803.59), 0.510 either side, the slots 0.550 off the bore's level","via":"harvest"}}],"adopt":{"from":"photo-right","reason":"The photo the outline is traced from; the other side reads 0.003 more."},"note":"The faces are taken at 45 degrees, their slots on the lines through the bore at 45 degrees (\"Full M-LOK compatibility (7 sides)\"): then the edge between a side flat and a diagonal comes out 0.30 from the bore's level, and the photos show it at 0.29 (side_flat_half_height)."},"side_flat_half_height":{"label":"A side flat's upper and lower edges, each from the bore's level (a check on the section)","kind":"length","measurements":[{"id":"photo","value":0.29,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard b0ebc4d7c105 and c3d5763fef0d (Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467)","scaleRef":"each photo's own rail pitch at its middle (std.picatinny.slot_pitch): 129.2 and 128.6 px/in","method":"where the webs between the slots step in brightness: the upper edge 0.283 and 0.272 in above the middle row of windows on the two photos (0.277), the lower in several steps 0.29 to 0.36 below it (0.32: the edge is broken); both are on the corner nearest the lens, 0.8 in off the middle, which reads 2.5% large about the lens's height (about an inch above the bore): 0.295 above and 0.288 below. The same handguard in FDE (b73e40fcdf82, bb47fb7d2cad), where the edges show as lines, has the upper one 0.30 above its middle row (.cache/batch123/expo-arms-mlok-15-handguard/facets.py)","via":"harvest"}}],"note":"Not built from: the section's own corner is where the side flat (width / 2) meets the 45 degree face (diagonal_face_distance), 0.30 from the bore's level."},"wall_at_slots":{"label":"The wall's thickness at the slots, as it shows in the diagonal rows (a check on the bore)","kind":"length","measurements":[{"id":"photo","value":0.11,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard b0ebc4d7c105 and c3d5763fef0d (Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467)","scaleRef":"each photo's own rail pitch at its middle (std.picatinny.slot_pitch); the slots taken 7 mm wide (std.mlok.slot_width)","method":"a 7 mm slot through a wall standing at 45 degrees shows 0.707 x (7 mm - the wall) open, a little more in the upper row and less in the lower as the lens stands above the bore: the upper rows' windows are 0.132 and 0.124 in high, the lower 0.098 and 0.096, which is a wall of 0.107 and 0.114","via":"harvest"}}],"note":"Not built from. The published 1.35 in bore inside the photos' faces leaves 0.12 at the side flats' middles, 0.10 at the diagonals' and 0.085 at the bottom's."},"neck_bottom_above_bore":{"label":"Where the upper diagonal faces end under the rail's neck, above the bore axis","kind":"length","measurements":[{"id":"photo","value":0.73,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard b0ebc4d7c105 and c3d5763fef0d (Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467)","scaleRef":"each photo's own rail pitch at its middle (std.picatinny.slot_pitch): 129.2 and 128.6 px/in","method":"the webs' brightness steps from the lit neck to the dark face 0.749 in above the middle row of windows on both photos; on the same handguard in FDE (b73e40fcdf82, bb47fb7d2cad) the line is 0.729 and 0.723 above it. Between the two; ± covers both","via":"harvest"}}]},"rail_top_flat_width":{"label":"Its rail's top flat, side to side","kind":"length","measurements":[{"id":"photo","value":0.64,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard b0ebc4d7c105 and c3d5763fef0d (Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467)","scaleRef":"the rail's own widest width, .835 (std.picatinny.top_width), which sets the lens's distance in each photo (33.2 and 35.3 in)","method":"the plane of the teeth's near sides at each height below their tops, as the middle windows read through them (width's method): a straight line from 0.0097 (0.0091) of the lens's distance at the top, twice which is 0.641 in on both photos","via":"harvest"}}],"note":"The rail's profile as the side photos' teeth give it: a flat, 45 degree bevels down to the widest (.835, std.picatinny.top_width), which the slots' floors (std.picatinny.slot_depth) just pass. A reading, and since 2026-10-12 not what the rail is drawn by: its head is the standard's in section (std.picatinny.*, pipeline/blender/lib.py rail_head), a flat .656 across and the widest from .0895 to .1105 under the top, which this reading and rail_widest_below_top are within their ± (the builder refuses to run if they stop being). Drawn as the two readings alone the faces met sharp at the widest, 0.009 in inside the standard's above it and 0.010 below: a gap each side of every clamp."},"rail_widest_below_top":{"label":"Its rail's widest line below its top","kind":"length","measurements":[{"id":"photo","value":0.1,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard b0ebc4d7c105 and c3d5763fef0d (Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467)","scaleRef":"each photo's own rail pitch at its middle (std.picatinny.slot_pitch): 129.2 and 128.6 px/in","method":"the height at which the teeth's near sides stop moving out with depth: between the rows 0.093 and 0.108 in below the tooth tops (left side), 0.085 and 0.116 (right); the flat and the 45 degree bevels reach .835 at 0.097","via":"harvest"}}]},"rail_underside_below_top":{"label":"Where its rail's underside ends on the neck, below its top","kind":"length","measurements":[{"id":"photo","value":0.21,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard b0ebc4d7c105 and c3d5763fef0d (Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467)","scaleRef":"each photo's own rail pitch at its middle (std.picatinny.slot_pitch): 129.2 and 128.6 px/in","method":"under the teeth the webs are in shadow down to a step up in brightness (rows 624.18 and 609.41 on the levelled photos), 0.206 in below the step at the tooth tops on both; on the same handguard in FDE (b73e40fcdf82, bb47fb7d2cad) 0.214 and 0.224 (.cache/batch123/expo-arms-mlok-15-handguard/facets.py)","via":"harvest"}}],"note":"From the rail's widest line the underside comes back in to the neck; taken at the standard's 45 degrees from the standard's widest (since 2026-10-12: its lower faces carried on to this height), which makes the neck 0.64 in wide under the rail (0.62 while the faces were drawn meeting sharp at rail_widest_below_top). From there the neck's sides are run straight to where the upper diagonal faces end (neck_bottom_above_bore)."},"rail_slot0_from_rear_face":{"label":"Its rail's rearmost slot (its centre) ahead of its rear face","kind":"length","measurements":[{"id":"photo-right","value":0.62,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard b0ebc4d7c105 (Primary Arms' gallery for XP-GUARD15-BLK, photo _01: the handguard's right side on white, the receiver's end at the left, 2200 x 1467)","scaleRef":"its own top rail's 35 teeth at the Picatinny pitch (std.picatinny.slot_pitch), fitted along the photo","method":"the rear land's front edge and the rearmost tooth's rear edge (0.312 and 0.089 behind that tooth's centre): the slot between them centred 0.200 behind it, half a pitch as every other is; the rear face 0.82 behind it (the rail's own end 0.824, the side face's edge 0.815)","via":"harvest"}},{"id":"photo-left","value":0.627,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard c3d5763fef0d (Primary Arms' gallery for XP-GUARD15-BLK, photo _02: its left side on white, the receiver's end at the right, 2200 x 1467)","scaleRef":"its own top rail's 35 teeth at the Picatinny pitch, fitted along the photo","method":"as the right side's: the rear face 14.220 behind the foremost tooth's centre, the rearmost slot 13.593","via":"harvest"}}],"adopt":{"from":"photo-right","reason":"The photo the outline is traced from; the other side reads 0.007 more."},"note":"The rail begins with a land 0.50 in long and ends with one 0.46 in long, its top edge chamfered (rail_front_chamfer); between them 36 slots, wider than the standard's (0.222 against .206 +.008: its teeth are 0.172 long). The model cuts them at the standard's width."},"rail_slots":{"label":"Slots in its top rail","kind":"count","measurements":[{"id":"photo","value":36,"unit":"count","source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard b0ebc4d7c105 and c3d5763fef0d (Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467)","scaleRef":"none: a count","method":"35 teeth between the two end lands on each photo, every one 49.8 to 51.1 px from the next: 36 slots","via":"harvest"}}]},"mlok_slot0_from_rear_face":{"label":"The rearmost M-LOK slot's centre ahead of its rear face (every row)","kind":"length","measurements":[{"id":"photo-right","value":2.935,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard b0ebc4d7c105 (Primary Arms' gallery for XP-GUARD15-BLK, photo _01: the handguard's right side on white, the receiver's end at the left, 2200 x 1467)","scaleRef":"its own top rail's 35 teeth at the Picatinny pitch (std.picatinny.slot_pitch), fitted along the photo; the slots 40 mm apart (std.mlok.slot_pitch)","method":"the middle row's eight windows fitted as near and far slot ends about the lens's foot (width's method): the rearmost slot's centre 2.115 ahead of the rearmost tooth's centre at its own depth (rms 0.0009 in), the rear face 0.82 behind it; the upper and lower rows 2.113 and 2.116","via":"harvest"}},{"id":"photo-left","value":2.937,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard c3d5763fef0d (Primary Arms' gallery for XP-GUARD15-BLK, photo _02: its left side on white, the receiver's end at the right, 2200 x 1467)","scaleRef":"its own top rail's 35 teeth at the Picatinny pitch, fitted along the photo; the slots 40 mm apart","method":"as the right side's: the foremost slot's centre 0.2587 behind the foremost tooth's (0.2590 and 0.2589 in the other rows), 1.032 behind the front face; seven pitches back from it in a body 14.993 long","via":"harvest"}}],"adopt":{"from":"photo-right","reason":"The photo the outline is traced from; the other side's rows are within 0.002 of it."},"note":"The three rows a side photo shows are in step (their rearmost slots within 0.003 in of each other), and the two sides mirror each other (the foremost slot 1.026 and 1.032 behind the front face). The slots read 1.28 in long, the standard's 32 mm within its ± 1."},"mlok_slot0_x":{"label":"The rearmost M-LOK slot's centre ahead of the receiver's front face","kind":"length","measurements":[{"id":"derived","value":2.49,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.rear_face_x} + {.mlok_slot0_from_rear_face}","via":"harvest"}}]},"mlok_slots":{"label":"M-LOK slots in each row","kind":"count","measurements":[{"id":"photo","value":8,"unit":"count","source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard b0ebc4d7c105 and c3d5763fef0d (Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467)","scaleRef":"none: a count","method":"eight windows in each of the three rows on each photo","via":"harvest"}}],"note":"Three rows show on each side (the upper diagonal, the side, the lower diagonal); the bottom's row shows only edge-on in the three-quarter photos and is taken to be the same eight (Primary Arms: \"Full M-LOK compatibility (7 sides)\")."},"reach_inside":{"label":"The room inside its faces, from the face in to the barrel (what an M-LOK accessory's nuts may take)","kind":"length","measurements":[],"note":"Not sourced: what runs under it is another part (a barrel, a gas block, a gas tube), so the room is the build's and not this part's."},"channel_width":{"label":"The channel in its top, under the rail (the gas tube's), side to side","kind":"length","measurements":[{"id":"photo","value":0.45,"unit":"in","pm":0.07,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard 68802fbed182 (Primary Arms' gallery for XP-GUARD15-BLK, photo _00: three-quarter view from the front right, 2200 x 1467)","scaleRef":"the rail's own widest width in the same plane, the front face: .835 (std.picatinny.top_width) between its two widest corners, 62 px across and 30 up","method":"the channel's two edges 33 px apart on one row of the front face, against the rail's width run the same way across that face (71.8 px/in along a row, the face's upright edges leaning 0.07): 0.46 in. Corners picked by eye to 3 px on a brightened crop: ± 0.07","via":"harvest"}}],"note":"A keyhole: the bore opens upward into a channel with a round roof. Its roof isn't measured: drawn round about the gas tube's standard height (std.ar15.gas_tube_above_bore)."},"bolt_first_from_rear_face":{"label":"The clamp's rearmost cross bolt, its axis ahead of the rear face","kind":"length","measurements":[{"id":"photo","value":0.5,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard b0ebc4d7c105 and c3d5763fef0d (Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467)","scaleRef":"each photo's own top rail's 35 teeth at the Picatinny pitch (std.picatinny.slot_pitch), fitted along it","method":"circles found on the bolts' ends (Hough): 0.492 ahead of the rear face on the right side, 0.511 on the left (its head)","via":"harvest"}}],"note":"Three cross bolts through the block under its rear end: socket heads on the left, and on the right two screw ends either side of a steel nut with a pointed top. A buyer on its page: \"5mm Allen Key for the screws\" (Pikamon, 2/26/2025); another has Primary Arms' torque for them: \"the cross bolts are 20-25 in-lbs and recommended with blue threadlocker\" (Kye, 10/11/2024)."},"bolt_spacing":{"label":"The clamp's cross bolts, axis to axis","kind":"length","measurements":[{"id":"photo","value":0.5,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard b0ebc4d7c105 and c3d5763fef0d (Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467)","scaleRef":"each photo's own top rail's 35 teeth at the Picatinny pitch (std.picatinny.slot_pitch), fitted along it","method":"the outer two 0.994 apart on the right side (0.492, 1.486) and 1.010 on the left (0.511, 1.521), the middle one halfway (0.997 on the left)","via":"harvest"}}]},"bolt_below_bore":{"label":"The clamp's cross bolts, their axes below the bore axis","kind":"length","measurements":[{"id":"photo","value":0.94,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard b0ebc4d7c105 and c3d5763fef0d (Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467)","scaleRef":"each photo's own rail pitch at its middle (std.picatinny.slot_pitch); the bore's level its middle row of windows","method":"circles found on them (Hough): the bolts' ends 0.967 in below the middle row of windows on the right side, their heads 0.911, 0.918 and 0.957 on the left","via":"harvest"}}]},"bolt_head_diameter":{"label":"A cross bolt's head (the left side)","kind":"length","measurements":[{"id":"photo","value":0.3,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard c3d5763fef0d (Primary Arms' gallery for XP-GUARD15-BLK, photo _02: its left side on white, the receiver's end at the right, 2200 x 1467)","scaleRef":"its own rail's pitch at the photo's middle (std.picatinny.slot_pitch): 129.4 px/in","method":"circles found on the three heads (Hough): 0.294, 0.328 and 0.277 in across","via":"harvest"}}]},"bolt_end_diameter":{"label":"A cross bolt's threaded end (the right side)","kind":"length","measurements":[{"id":"photo","value":0.19,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard b0ebc4d7c105 (Primary Arms' gallery for XP-GUARD15-BLK, photo _01: the handguard's right side on white, the receiver's end at the left, 2200 x 1467)","scaleRef":"its own rail's pitch at the photo's middle (std.picatinny.slot_pitch): 129.6 px/in","method":"circles found on the two screw ends (Hough): 0.170 and 0.213 in across","via":"harvest"}}]},"nut_face_diameter":{"label":"The clamp's steel nut on the right side: its round, about the middle bolt","kind":"length","measurements":[{"id":"photo-fde","value":0.44,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard b73e40fcdf82 (Primary Arms' gallery for XP-GUARD15-FDE, photo _01: the same handguard in FDE Cerakote, its right side on white, 2200 x 1467)","scaleRef":"that photo's own rail pitch at its middle (std.picatinny.slot_pitch): 49.04 px a tooth, 124.5 px/in in the rail's mid-plane, 1% more at the block's face","method":"the black shape's widest rows on the levelled photo (rows 847 to 859): 55 and 56 px across, 0.437 and 0.445 in; they are 0.95 in below the middle row of windows, the cross bolts' level (.cache/batch123/expo-arms-mlok-15-handguard: the mask is nut-mask.png)","via":"harvest"}}],"note":"A buyer on its page calls it \"the locking key\", which sits \"into the groove of the barrel nut\" (Pikamon, 2/26/2025). Black on the FDE handguard, so its outline is read there: a round about the middle bolt, and above it a neck that tapers to a blunt point on the lower diagonal face (the three entries below). On the black handguard's photo only a ring 0.32 in across shows inside it."},"nut_tip_above_bolt":{"label":"The clamp's nut: its point above the middle bolt's axis","kind":"length","measurements":[{"id":"photo-fde","value":0.375,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard b73e40fcdf82 (Primary Arms' gallery for XP-GUARD15-FDE, photo _01: the same handguard in FDE Cerakote, its right side on white, 2200 x 1467)","scaleRef":"that photo's own rail pitch at its middle (std.picatinny.slot_pitch): 49.04 px a tooth, 124.5 px/in in the rail's mid-plane, 1% more at the block's face","method":"the black shape's top row (808) is 0.583 in below the middle row of windows, its widest rows 0.955: 0.372 apart","via":"harvest"}}]},"nut_shoulder_above_bolt":{"label":"The clamp's nut: where its neck's straight sides end under the point, above the middle bolt's axis","kind":"length","measurements":[{"id":"photo-fde","value":0.34,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard b73e40fcdf82 (Primary Arms' gallery for XP-GUARD15-FDE, photo _01: the same handguard in FDE Cerakote, its right side on white, 2200 x 1467)","scaleRef":"that photo's own rail pitch at its middle (std.picatinny.slot_pitch): 49.04 px a tooth, 124.5 px/in in the rail's mid-plane, 1% more at the block's face","method":"row by row the neck narrows evenly (0.334 in wide 0.18 above the bolts' level, 0.270 at 0.25, 0.230 at 0.30, 0.207 at 0.32) and then closes within 0.05 in: the even taper ends about 0.34 above","via":"harvest"}}]},"nut_shoulder_width":{"label":"The clamp's nut: its neck's width where the straight sides end","kind":"length","measurements":[{"id":"photo-fde","value":0.2,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard b73e40fcdf82 (Primary Arms' gallery for XP-GUARD15-FDE, photo _01: the same handguard in FDE Cerakote, its right side on white, 2200 x 1467)","scaleRef":"that photo's own rail pitch at its middle (std.picatinny.slot_pitch): 49.04 px a tooth, 124.5 px/in in the rail's mid-plane, 1% more at the block's face","method":"the black shape is 0.207 in wide 0.32 above the bolts' level and 0.167 at 0.35","via":"harvest"}}],"note":"The neck's sides run straight from the round's widest points to here: that line is 0.315 in wide 0.18 above the bolts' level, 0.263 at 0.25 and 0.229 at 0.30, where the photo has 0.334, 0.270 and 0.230."},"rail_front_chamfer":{"label":"The chamfer on its rail's front end (the top edge of the front land)","kind":"length","measurements":[{"id":"photo","value":0.11,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/expo-arms-mlok-15-handguard b0ebc4d7c105 (Primary Arms' gallery for XP-GUARD15-BLK, photo _01: the handguard's right side on white, the receiver's end at the left, 2200 x 1467)","scaleRef":"its own top rail's 35 teeth at the Picatinny pitch (std.picatinny.slot_pitch), fitted along the photo","method":"the silhouette's front end row by row: 14.078 ahead of the rearmost tooth's centre 0.023 in below the tooth tops, 14.114, 14.137, 14.156 and 14.170 by 0.116 below, where it is the front face; the left side's photo (c3d5763fef0d) has 0.07 back over 0.07 down","via":"harvest"}}],"note":"Taken at 45 degrees: the photo gives 0.11 back for 0.116 down. The rear end's is a fifth of it (0.02) and is left to the edges' break."}}},{"subject":"expo-arms-stripped-upper","title":"Expo Arms 7075 Stripped AR-15 Upper Receiver (XP-UPPER)","dimensions":{"weight":{"label":"Weight (the stripped receiver: no port door, forward assist or barrel)","kind":"mass","measurements":[],"note":"No page states one: Primary Arms' page for it (the brand owner's) has no weight row and none in its text, its T-marked sibling's page none, and no seller or reviewer on file gives a figure. Not estimated: a build with it says its total is unknown (D61)."},"bore_axis_above_pin":{"label":"Bore axis above the takedown pin centre","kind":"length","measurements":[{"id":"standard","value":0.8775,"unit":"in","pm":0.0015,"source":{"type":"derived","expr":"{std.ar15.bore_axis_y}","via":"harvest"},"note":"The standard's. Primary Arms' page: \"Accepts MIL-SPEC upper parts\"; \"It is compatible with standard mil-spec lowers, handguards, and barrels\"."},{"id":"right","value":0.876,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/expo-arms-stripped-upper aad70ef8abd5 (Primary Arms' XP-UPPER_02: the stripped receiver's right side, level, 2200 x 1467)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each bore's near and far edges fitted as circles (rms 0.06 to 0.08 px), their midpoints the frame's points: 256.86 px/in on the receiver's mid-plane; the rail's 13 slots fit the standard pitch to 0.07% on it","method":"the threaded nose's top and bottom edges (y 1.492 and 0.260 over x 6.7 to 6.9: its silhouette's edges lie on the mid-plane from a level lens): their middle; ± is 1.5 px","via":"harvest"}}],"adopt":{"from":"standard","reason":"The drawings' figure; this receiver's own photo puts its nose's axis within 0.002 of it."}},"rail_top_above_pin":{"label":"The top rail's surface above the pin line","kind":"length","measurements":[{"id":"right","value":2.092,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/expo-arms-stripped-upper aad70ef8abd5 (Primary Arms' XP-UPPER_02: the stripped receiver's right side, level, 2200 x 1467)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each bore's near and far edges fitted as circles (rms 0.06 to 0.08 px), their midpoints the frame's points: 256.86 px/in on the receiver's mid-plane; the rail's 13 slots fit the standard pitch to 0.07% on it","method":"the rail's tooth tops along x 1.0 to 6.0 read 2.103 at mid-length (2.108 at the takedown hole, 2.098 at the pivot: the receiver is yawed 2 degrees, its rear nearer); the silhouette's top is the tooth's near edge, 0.31 to 0.42 nearer than the mid-plane: the lens stands about 36 in away opposite x 1.69, y 1.04 (right_photo_lens_*), so what is z nearer than the mid-plane reads large about that point by 36 / (36 - z), 0.011 less; ± is 1.5 px and that edge's place","via":"harvest"}},{"id":"left","value":2.09,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/expo-arms-stripped-upper 8888fc8d0ccb (Primary Arms' XP-UPPER_03: the stripped receiver's left side, from above, 2200 x 1467)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart, each bore's near and far edges fitted as circles, their midpoints the frame's points: 254.51 px/in on the mid-plane at the pin line (the rail, nearer the lens from above, reads 0.71% larger by its slots' pitch)","method":"the tooth tops read 2.106 at mid-length; from above the silhouette's top is the tooth's far edge and the rail 0.7% nearer the lens than the pin line (the lens stands about 35 in away opposite x 3.36 and some 5 in above the pin line (left_photo_lens_*)): 0.015 less, ± 0.01 for where the lens stood","via":"harvest"}}],"adopt":{"from":"right","reason":"The level view; the view from above agrees within its ±."},"note":"Read on Primary Arms' own two photos, each in the frame of its own lug holes. One reviewer on its page calls it \"a high rise upper\" whose rail \"sticks up above the handguard\": the catalog's other forged receiver reads 2.09 the same way (aero-m4e1-threaded-upper.rail_top_above_pin) and the reference model of a mil-spec forging has 2.090, so its rail stands where a mil-spec flat top's does."},"rail_slot0_x":{"label":"The rearmost rail slot's centre ahead of the takedown pin","kind":"length","measurements":[{"id":"right","value":1.314,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/expo-arms-stripped-upper aad70ef8abd5 (Primary Arms' XP-UPPER_02: the stripped receiver's right side, level, 2200 x 1467)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each bore's near and far edges fitted as circles (rms 0.06 to 0.08 px), their midpoints the frame's points: 256.86 px/in on the receiver's mid-plane; the rail's 13 slots fit the standard pitch to 0.07% on it","method":"the top edge's 13 slot floors, their centres fitted to the standard pitch: 1.316 (rms 0.003; the pitch fits 0.3943), less 0.002 for the yaw; a slot's centre in the silhouette is its centre on the mid-plane","via":"harvest"}},{"id":"left","value":1.3,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/expo-arms-stripped-upper 8888fc8d0ccb (Primary Arms' XP-UPPER_03: the stripped receiver's left side, from above, 2200 x 1467)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart, each bore's near and far edges fitted as circles, their midpoints the frame's points: 254.51 px/in on the mid-plane at the pin line (the rail, nearer the lens from above, reads 0.71% larger by its slots' pitch)","method":"the 13 slot centres run 1.286 to 6.048, 0.7% wide about the image's middle (x 3.19): 1.300 to 6.028 at the pin line's scale","via":"harvest"}}],"adopt":{"from":"right","reason":"The level view; the view from above reads 0.014 less, within its ±."}},"rail_slots":{"label":"How many rail slots","kind":"count","measurements":[{"id":"photo","value":13,"unit":"count","source":{"type":"photo","photo":"references/expo-arms-stripped-upper aad70ef8abd5 (Primary Arms' XP-UPPER_02: the stripped receiver's right side, level, 2200 x 1467)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each bore's near and far edges fitted as circles (rms 0.06 to 0.08 px), their midpoints the frame's points: 256.86 px/in on the receiver's mid-plane; the rail's 13 slots fit the standard pitch to 0.07% on it","method":"counted along the top edge; the left photo shows the same 13","via":"harvest"}}],"note":"Behind the first is a solid run of rail over the charging handle's channel (from rail_rear_x), ahead of the last a long tooth to the front shoulder."},"rail_rear_x":{"label":"The top rail's head: where it begins ahead of the tongue, X (the app draws the head from here)","kind":"length","measurements":[{"id":"standard","value":0.4165,"unit":"in","pm":0.006,"source":{"type":"derived","expr":"{std.ar15.rail_tongue_shoulder_x}","via":"user"}}],"note":"Until 2026-10-20 this was the rail's rearmost point (now rail_tongue_rear_x), and the app drew the head at its full width from there, square: the charging handle's T, cut round for a rounded rail end, stood in its corners. Behind this the rail is the standard's tongue (std.ar15.rail_tongue_*), which the receiver's model carries, as the 22RB's does."},"rail_tongue_rear_x":{"label":"The top rail's tongue: its rounded end's rearmost point, X ahead of the takedown pin","kind":"length","measurements":[{"id":"photo","value":-0.588,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/expo-arms-stripped-upper aad70ef8abd5 (Primary Arms' XP-UPPER_02: the stripped receiver's right side, level, 2200 x 1467)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each bore's near and far edges fitted as circles (rms 0.06 to 0.08 px), their midpoints the frame's points: 256.86 px/in on the receiver's mid-plane; the rail's 13 slots fit the standard pitch to 0.07% on it","method":"where the top edge first reaches the teeth's height (the tail's end is rounded in plan, as the three-quarter views show: its tip is on the mid-plane); the left photo reads -0.616 at the rail's 0.7% larger scale about x 3.19: -0.589","via":"harvest"}}]},"rail_front_x":{"label":"The top rail's front end ahead of the takedown pin","kind":"length","measurements":[{"id":"shoulder","value":6.591,"unit":"in","pm":0.011,"source":{"type":"derived","expr":"{.front_face_x} - {std.ar15.upper_barrel_thread_length}","via":"harvest"},"note":"The rail's last tooth ends flush with the body's front shoulder, where the barrel-nut thread begins (both photos): the drawing's .445 REF behind the front face."},{"id":"right","value":6.59,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/expo-arms-stripped-upper aad70ef8abd5 (Primary Arms' XP-UPPER_02: the stripped receiver's right side, level, 2200 x 1467)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each bore's near and far edges fitted as circles (rms 0.06 to 0.08 px), their midpoints the frame's points: 256.86 px/in on the receiver's mid-plane; the rail's 13 slots fit the standard pitch to 0.07% on it","method":"the silhouette's front edge at the rail's height reads 6.640; it is the shoulder's near edge, about 0.37 nearer than the mid-plane: the lens stands about 36 in away opposite x 1.69, y 1.04 (right_photo_lens_*), so what is z nearer than the mid-plane reads large about that point by 36 / (36 - z), 0.050 less","via":"harvest"}}],"adopt":{"from":"shoulder","reason":"The drawing's shoulder; the photo's edge lands on it."},"note":"Ahead of it the receiver is the barrel nut's thread."},"receiver_rear_x":{"label":"The receiver's rear face behind the takedown pin (negative)","kind":"length","measurements":[{"id":"standard","value":-0.621,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.ar15.upper_rear_face_x}","via":"harvest"},"note":"The Army's drawing of the upper (8448524). Primary Arms' page: \"Accepts MIL-SPEC upper parts\"; \"It is compatible with standard mil-spec lowers, handguards, and barrels\"."},{"id":"left","value":-0.625,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/expo-arms-stripped-upper 8888fc8d0ccb (Primary Arms' XP-UPPER_03: the stripped receiver's left side, from above, 2200 x 1467)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart, each bore's near and far edges fitted as circles, their midpoints the frame's points: 254.51 px/in on the mid-plane at the pin line (the rail, nearer the lens from above, reads 0.71% larger by its slots' pitch)","method":"the silhouette's rear edge at y 1.5 to 1.8, the flat left side's rear corner (z 0.32 nearer than the mid-plane), reads -0.682: 0.021 less for the scale at that height, 0.036 less for the near edge (the lens stands about 35 in away opposite x 3.36 and some 5 in above the pin line (left_photo_lens_*))","via":"harvest"}},{"id":"right","value":-0.636,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/expo-arms-stripped-upper aad70ef8abd5 (Primary Arms' XP-UPPER_02: the stripped receiver's right side, level, 2200 x 1467)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each bore's near and far edges fitted as circles (rms 0.06 to 0.08 px), their midpoints the frame's points: 256.86 px/in on the receiver's mid-plane; the rail's 13 slots fit the standard pitch to 0.07% on it","method":"the silhouette's rear edge at y 1.45 to 1.62 reads -0.666 where the forward assist's housing joins the wall; taken as an edge 0.32 nearer than the mid-plane it is -0.645, at 0.6 nearer -0.627: ± covers that","via":"harvest"}}],"adopt":{"from":"standard","reason":"The drawing dimensions the face; both photos agree with it within their ±."}},"front_face_x":{"label":"The receiver's front face (the end of its barrel-nut thread) ahead of the takedown pin","kind":"length","measurements":[{"id":"standard","value":7.036,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.ar15.upper_front_face_x}","via":"harvest"},"note":"The Army's drawing: .661 ahead of the pivot lug's hole. Primary Arms' page: \"Accepts MIL-SPEC upper parts\"; \"It is compatible with standard mil-spec lowers, handguards, and barrels\"."},{"id":"right","value":7.029,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/expo-arms-stripped-upper aad70ef8abd5 (Primary Arms' XP-UPPER_02: the stripped receiver's right side, level, 2200 x 1467)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each bore's near and far edges fitted as circles (rms 0.06 to 0.08 px), their midpoints the frame's points: 256.86 px/in on the receiver's mid-plane; the rail's 13 slots fit the standard pitch to 0.07% on it","method":"the silhouette's front tip reads 7.121: the thread's near rim, 0.62 nearer than the mid-plane and 5.4 in from where the lens stands: the lens stands about 36 in away opposite x 1.69, y 1.04 (right_photo_lens_*), so what is z nearer than the mid-plane reads large about that point by 36 / (36 - z), 0.093 less (the rim's arc sags 0.09 there, as that angle makes it)","via":"harvest"}},{"id":"left","value":7.034,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/expo-arms-stripped-upper 8888fc8d0ccb (Primary Arms' XP-UPPER_03: the stripped receiver's left side, from above, 2200 x 1467)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart, each bore's near and far edges fitted as circles, their midpoints the frame's points: 254.51 px/in on the mid-plane at the pin line (the rail, nearer the lens from above, reads 0.71% larger by its slots' pitch)","method":"the tip reads 7.113: 0.012 less for the scale at the bore's height, 0.066 less for the near rim (the lens stands about 35 in away opposite x 3.36 and some 5 in above the pin line (left_photo_lens_*))","via":"harvest"}}],"adopt":{"from":"standard","reason":"The drawing dimensions the face; both photos land on it within their ±."}},"underside_y":{"label":"The receiver's underside above the pin line","kind":"length","measurements":[{"id":"standard","value":0.2485,"unit":"in","pm":0.0015,"source":{"type":"derived","expr":"{std.ar15.deck_y}","via":"harvest"},"note":"It sits on the lower's deck."},{"id":"right","value":0.25,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/expo-arms-stripped-upper aad70ef8abd5 (Primary Arms' XP-UPPER_02: the stripped receiver's right side, level, 2200 x 1467)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each bore's near and far edges fitted as circles (rms 0.06 to 0.08 px), their midpoints the frame's points: 256.86 px/in on the receiver's mid-plane; the rail's 13 slots fit the standard pitch to 0.07% on it","method":"the silhouette's lower edge between the lugs reads 0.238 to 0.246: the wall's near lower edge, 0.45 nearer than the mid-plane and 0.8 below where the lens stands: the lens stands about 36 in away opposite x 1.69, y 1.04 (right_photo_lens_*), so what is z nearer than the mid-plane reads large about that point by 36 / (36 - z), 0.010 more","via":"harvest"}}],"adopt":{"from":"standard","reason":"The lower's deck; the photo's edge lands on it."}},"width":{"label":"Width of the receiver's body","kind":"length","measurements":[{"id":"tdp","value":1.18,"unit":"in","pm":0.02,"stated":"FORGED DIA 1.18 DIA REF -V-","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 2 of 2, rev G: View G-G; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p109","via":"user"},"note":"The round body just behind the threaded nose, as aero-m4e1-threaded-upper.width reads it. Not measured on this receiver: no end or top view of it is on file."}],"note":"The mil-spec forging's: its page calls it a \"Precision machined 7075-T6 aluminum forging\" that \"Accepts MIL-SPEC upper parts\". Its forward assist's housing and brass deflector stand out past it on the right."},"charging_handle_above_bore":{"label":"The charging handle's channel above the bore's axis","kind":"length","measurements":[{"id":"photo","value":0.87,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/expo-arms-stripped-upper aad70ef8abd5 (Primary Arms' XP-UPPER_02: the stripped receiver's right side, level, 2200 x 1467)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each bore's near and far edges fitted as circles (rms 0.06 to 0.08 px), their midpoints the frame's points: 256.86 px/in on the receiver's mid-plane; the rail's 13 slots fit the standard pitch to 0.07% on it","method":"the notch in the traced outline's rear end, from the wall's top at 1.595 to the rail's tail's underside at 1.894: its middle less the bore's 0.8775","via":"harvest"}},{"id":"standard","value":0.8563,"unit":"in","pm":0.007,"source":{"type":"derived","expr":"{std.ar15.charging_handle_axis_y} - {.bore_axis_above_pin}","via":"user"},"note":"Riding on its guide lugs on the channel's tier: std.ar15.charging_handle_axis_y."}],"adopt":{"from":"standard","reason":"A handle rides on its guide lugs on the channel's tier (std.ar15.charging_handle_axis_y, the Army's drawing's); the photo reads the see-through notch's middle, which is the room the handle's block lies in, and agrees within its ±."},"note":"The notch the handle's latch end lies in: the handle lies at its height (as aero-m4e1-threaded-upper.charging_handle_above_bore)."},"handle_seat_x":{"label":"The charging handle's seat: the front wall of the open notch under the rail's rear end, ahead of the takedown pin","kind":"length","measurements":[{"id":"right","value":0.069,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/expo-arms-stripped-upper aad70ef8abd5 (Primary Arms' XP-UPPER_02: the stripped receiver's right side, level, 2200 x 1467)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each bore's near and far edges fitted as circles (rms 0.06 to 0.08 px), their midpoints the frame's points: 256.86 px/in on the receiver's mid-plane; the rail's 13 slots fit the standard pitch to 0.07% on it","method":"the see-through notch's front wall in the traced outline (profiles.side): its flat at x 0.069 from y 1.675 to 1.83, between two corners cut back to x 0.013 and -0.014. What shows through a notch is bounded by the wall's near edge, 0.32 to 0.45 nearer than the mid-plane (the flat side, or the rail's foot): the lens stands about 36 in away opposite x 1.69 (right_photo_lens_*), so that edge reads 0.015 to 0.020 behind the wall itself, which would be at 0.084 to 0.089; ± covers it","via":"harvest"}},{"id":"left","value":0.045,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/expo-arms-stripped-upper 8888fc8d0ccb (Primary Arms' XP-UPPER_03: the stripped receiver's left side, from above, 2200 x 1467)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart, each bore's near and far edges fitted as circles, their midpoints the frame's points: 254.51 px/in on the mid-plane at the pin line (the rail, nearer the lens from above, reads 0.71% larger by its slots' pitch)","method":"the same wall in the left outline (profiles.left): x 0.043 to 0.047 from y 1.631 to 1.781. The near edge again, the lens about 35 in away opposite x 3.36 (left_photo_lens_*): it reads 0.03 to 0.04 behind the wall itself, which would be at 0.076 to 0.088; ± covers it","via":"harvest"}},{"id":"tdp","value":0.075,"unit":"in","pm":0.015,"source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: side elevation, scaled (the notch has no callout in this view); user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"},"note":"Scaled, not a callout. On the 6600 px scan the two lug holes, fitted as circles, are 1966 px apart (308.4 px/in over std.ar15.pin_spacing) and the notch's front wall (column 2427.5) is 21.5 px ahead of the takedown hole's centre: 0.070. From the rear face's line, 217 px behind the wall, it is 0.083: the drawing dimensions that face at -0.621 and the scan has it at -0.634 by the holes. Between the two; ± covers both. The notch is 0.31 to 0.32 high there, for the handle's .2985 (drawing 8448518), its front corners cut back 0.06."}],"adopt":{"from":"right","reason":"This receiver's own notch in the outline its model is built from, where the model's wall is: a handle seated there stands in nothing. The Army's drawing, scaled, reads 0.006 more, and the left photo 0.024 less by its nearer edge; all three within their ±."},"note":"Where a charging handle stops. The notch is cut across the receiver under the rail's rear end and is open to the rear: the handle's block (its T ahead of the wings or latches, as thick as the shaft) lies in it with its shoulder against this wall, and the shaft runs on through the slot ahead of it. Until 2026-10-05 the handle was placed with its shoulder at the rear face, 0.69 in behind this (that day's review of the models: its whole T hung behind the receiver, over the castle nut, its latch's hook 0.6 in behind the slot traced for it on this receiver's left side, latch_slot in profiles.left: x 0.198 to 0.371). Magpul's photo of a handle in a receiver (references/magpul-mbus-3-rear 9248df8685e9) has it so: the T's wing astride the rear face, the notch filled to its front wall."},"right_photo_lens_distance":{"label":"The right side photo: its lens's distance from the receiver's mid-plane","kind":"length","measurements":[{"id":"holes","value":36,"unit":"in","pm":2,"source":{"type":"photo","photo":"references/expo-arms-stripped-upper aad70ef8abd5 (Primary Arms' XP-UPPER_02: the stripped receiver's right side, level, 2200 x 1467)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each bore's near and far edges fitted as circles (rms 0.06 to 0.08 px), their midpoints the frame's points: 256.86 px/in on the receiver's mid-plane; the rail's 13 slots fit the standard pitch to 0.07% on it","method":"the two bores' far edges are 1626.2 px apart and their near ones 1648.7: the far faces of the lugs are 1.384% further than the near ones, 0.4945 behind them (lug_width): 35.7 in to the near faces. The rail's pitch on the near faces' scale (0.9938 of the standard) gives 40 +3/-3; ± covers both","via":"harvest"}}],"note":"A property of Primary Arms' photo aad70ef8abd5, not of the receiver: the model corrects what the right side shows nearer the lens (the forward assist's housing, the deflector, the hinge lugs) by it."},"right_photo_lens_x":{"label":"The right side photo: where its lens stands, X","kind":"length","measurements":[{"id":"holes","value":1.69,"unit":"in","pm":0.1,"source":{"type":"photo","photo":"references/expo-arms-stripped-upper aad70ef8abd5 (Primary Arms' XP-UPPER_02: the stripped receiver's right side, level, 2200 x 1467)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each bore's near and far edges fitted as circles (rms 0.06 to 0.08 px), their midpoints the frame's points: 256.86 px/in on the receiver's mid-plane; the rail's 13 slots fit the standard pitch to 0.07% on it","method":"each bore's far edge sits off its near one toward the point the lens is opposite: +5.9, -3.6 px at the takedown hole, -16.6, -3.7 px at the pivot; the two lines meet at px (708, 708). The thread's rim sags 0.09 at the front as that makes it, and the rail's teeth show their rear faces ahead of about x 2","via":"harvest"}}]},"right_photo_lens_y":{"label":"The right side photo: where its lens stands, Y","kind":"length","measurements":[{"id":"holes","value":1.04,"unit":"in","pm":0.1,"source":{"type":"photo","photo":"references/expo-arms-stripped-upper aad70ef8abd5 (Primary Arms' XP-UPPER_02: the stripped receiver's right side, level, 2200 x 1467)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each bore's near and far edges fitted as circles (rms 0.06 to 0.08 px), their midpoints the frame's points: 256.86 px/in on the receiver's mid-plane; the rail's 13 slots fit the standard pitch to 0.07% on it","method":"as right_photo_lens_x: px row 708, level with the bore","via":"harvest"}}]},"left_photo_lens_distance":{"label":"The left side photo: its lens's distance from the receiver's mid-plane","kind":"length","measurements":[{"id":"holes","value":34.8,"unit":"in","pm":2,"source":{"type":"photo","photo":"references/expo-arms-stripped-upper 8888fc8d0ccb (Primary Arms' XP-UPPER_03: the stripped receiver's left side, from above, 2200 x 1467)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart, each bore's near and far edges fitted as circles, their midpoints the frame's points: 254.51 px/in on the mid-plane at the pin line (the rail, nearer the lens from above, reads 0.71% larger by its slots' pitch)","method":"the bores' far edges are 1611.0 px apart and their near ones 1634.0: 1.430% over the lugs' 0.4945 (lug_width)","via":"harvest"}}],"note":"A property of Primary Arms' photo 8888fc8d0ccb."},"left_photo_lens_x":{"label":"The left side photo: where its lens stands, X","kind":"length","measurements":[{"id":"holes","value":3.36,"unit":"in","pm":0.1,"source":{"type":"photo","photo":"references/expo-arms-stripped-upper 8888fc8d0ccb (Primary Arms' XP-UPPER_03: the stripped receiver's left side, from above, 2200 x 1467)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart, each bore's near and far edges fitted as circles, their midpoints the frame's points: 254.51 px/in on the mid-plane at the pin line (the rail, nearer the lens from above, reads 0.71% larger by its slots' pitch)","method":"each bore's far edge sits off its near one toward that point: -12.1, -19.7 px at the takedown hole, +10.9, -17.4 px at the pivot","via":"harvest"}}]},"left_photo_lens_y":{"label":"The left side photo: where its lens stands, Y","kind":"length","measurements":[{"id":"holes","value":4.8,"unit":"in","pm":0.5,"source":{"type":"photo","photo":"references/expo-arms-stripped-upper 8888fc8d0ccb (Primary Arms' XP-UPPER_03: the stripped receiver's left side, from above, 2200 x 1467)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart, each bore's near and far edges fitted as circles, their midpoints the frame's points: 254.51 px/in on the mid-plane at the pin line (the rail, nearer the lens from above, reads 0.71% larger by its slots' pitch)","method":"as left_photo_lens_x: the two holes' offsets put it 4.8 and 5.5 above the pin line; the rail's top and the underside's edge, read against the right photo's, fit 4.4","via":"harvest"}}]},"body_radius":{"label":"The round body's radius about the bore (the forging's)","kind":"length","measurements":[{"id":"tdp","value":0.59,"unit":"in","pm":0.01,"stated":"FORGED DIA 1.18 DIA REF -V-","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 2 of 2, rev G: View G-G; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p109","via":"user"}},{"id":"model","value":0.6,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): cylindrical faces r 0.6000 about the bore's axis, x -0.43 to 6.59","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's forged figure; the model's is 0.01 more."}},"bore_d":{"label":"The bore the bolt carrier runs in","kind":"length","measurements":[{"id":"tdp","value":1,"unit":"in","pm":0.002,"stated":"DIA -P- (IN 1.000 DIA ±.002 AREA)","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: note 4; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}}]},"dovetail_foot_y":{"label":"The rail's dovetail, its foot (where the neck begins), Y above the pin line","kind":"length","measurements":[{"id":"model","value":1.885,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the planes under the dovetail at y 1.885, z 0.309 to 0.333","via":"user"}},{"id":"photo","value":1.888,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/expo-arms-stripped-upper aad70ef8abd5 (Primary Arms' XP-UPPER_02: the stripped receiver's right side, level, 2200 x 1467)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each bore's near and far edges fitted as circles (rms 0.06 to 0.08 px), their midpoints the frame's points: 256.86 px/in on the receiver's mid-plane; the rail's 13 slots fit the standard pitch to 0.07% on it","method":"the dark line under the rail, px row 487 at u 700: 1.895, an edge 0.33 nearer than the mid-plane: the lens stands about 36 in away opposite x 1.69, y 1.04 (right_photo_lens_*), so what is z nearer than the mid-plane reads large about that point by 36 / (36 - z)","via":"harvest"}}],"adopt":{"from":"model","reason":"The model's face; this receiver's photo agrees within its ±."}},"dovetail_foot_half_width":{"label":"The rail's dovetail at its foot, half its width","kind":"length","measurements":[{"id":"model","value":0.333,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the planes at y 1.885 reach z 0.333","via":"user"}},{"id":"std","value":0.321,"unit":"in","pm":0.013,"source":{"type":"derived","expr":"{std.picatinny.bevel_width} / 2 + {std.picatinny.lower_gauge_below_top} - ({.rail_top_above_pin} - {.dovetail_foot_y})","via":"harvest"},"note":"The standard's lower face carried on at its 45 degrees from the lower gauge line (.748 across, .154 below the rail's top) to the height the reference model has the foot at: the face every other rail on file has (the teeth the app draws on this body, a handguard's own rail) and every clamp's channel is cut to. ± is the gauge line's .010 and the model's .003."}],"adopt":{"from":"std","reason":"The standard's, since 2026-10-12: a rail's head is MIL-STD-1913's, and the clamps' channels are cut to it (pipeline/blender/lib.py rail_seat). The reference model draws the same face a hundredth further out, at the standard's stated .164 where the ledger has the middle of .164 -.020 (std.picatinny.lower_gauge_below_top): inside the standard's band, and on a body drawn so every clamp stood 0.008 in into the rail along both sides (0.001 cubic inches of an Aimpoint's base). The model isn't authoritative beside the standard (D49); its neck and the foot's height are still its own."}},"rail_neck_half_width":{"label":"The rail's neck below its dovetail, half its width","kind":"length","measurements":[{"id":"model","value":0.309,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the planes at y 1.700 and 1.885 begin at z 0.309","via":"user"}}]},"rail_neck_bottom_y":{"label":"The rail's neck, where it meets the receiver's sides, Y","kind":"length","measurements":[{"id":"model","value":1.7,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the planes at y 1.700, z 0.309 to 0.319","via":"user"}},{"id":"photo","value":1.698,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/expo-arms-stripped-upper aad70ef8abd5 (Primary Arms' XP-UPPER_02: the stripped receiver's right side, level, 2200 x 1467)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each bore's near and far edges fitted as circles (rms 0.06 to 0.08 px), their midpoints the frame's points: 256.86 px/in on the receiver's mid-plane; the rail's 13 slots fit the standard pitch to 0.07% on it","method":"the line along the side under the rail's neck, px row 536 at u 700: 1.704, an edge 0.32 nearer than the mid-plane: the lens stands about 36 in away opposite x 1.69, y 1.04 (right_photo_lens_*), so what is z nearer than the mid-plane reads large about that point by 36 / (36 - z)","via":"harvest"}}],"adopt":{"from":"model","reason":"The model's face; this receiver's photo agrees within its ±."}},"side_half_width":{"label":"The receiver's sides below the rail's neck, half its width","kind":"length","measurements":[{"id":"model","value":0.319,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the planes at y 1.700 end at z 0.319; a .10 fillet below them","via":"user"}}]},"side_bottom_y":{"label":"The receiver's sides, where they turn into the round body, Y","kind":"length","measurements":[{"id":"model","value":1.44,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the r .10 fillet between the flat side and the round body, its axis at y 1.440, z 0.419","via":"user"}}]},"lug_wall_half_width":{"label":"The walls below the round body down to the underside, half the width","kind":"length","measurements":[{"id":"model","value":0.453,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the r .075 fillets at y 0.458, their axes at z 0.528","via":"user"}}]},"rear_flange_r":{"label":"The flange round the rear end, its radius about the bore","kind":"length","measurements":[{"id":"model","value":0.6938,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): cylindrical faces r 0.6938 about the bore's axis from the rear face to x -0.470, on both sides","via":"user"}}],"note":"The raised lip that follows the rear end's contour: the left photo shows it, its front edge about 0.2 ahead of the rear face."},"rear_flange_front_x":{"label":"The rear flange's front face, X","kind":"length","measurements":[{"id":"model","value":-0.47,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the r 0.6938 faces end at x -0.470","via":"user"}}]},"lug_width":{"label":"The takedown and pivot lugs' width","kind":"length","measurements":[{"id":"tdp","value":0.4945,"unit":"in","pm":0.0015,"stated":".496 -.003 BOTH LUGS","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: the rear elevation; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}}],"note":"The reference model has them 0.494."},"lug_rear_face_top_y":{"label":"The takedown lug's rear face, how high it rises into the body, Y","kind":"length","measurements":[{"id":"model","value":0.458,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/batch123/expo-arms-stripped-upper/cad.py): the plane x -0.236 from y -0.212 to 0.458; the r .75 corner faces lie outside z ±0.247","via":"user"}}],"note":"Behind it the body's lower rear is cut away either side of the lug's width, to the arc a lower's rear walls rise along (std.ar15.rear_wall_arc_r; the upper's own is std.ar15.upper_rear_corner_r)."},"lug_hole_d":{"label":"The lugs' pin holes","kind":"length","measurements":[{"id":"tdp","value":0.251,"unit":"in","pm":0.001,"stated":".250 DIA +.002 THRU (the takedown lug's, CSK .31 DIA X 90 INCL THIS SIDE ONLY); .250 DIA +.001 THRU (the pivot lug's)","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: side elevation; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}}],"note":"Both photos' holes read 0.254 to 0.256 across on the near faces' scale."},"barrel_thread_major_d":{"label":"The barrel-nut thread's major diameter","kind":"length","measurements":[{"id":"tdp","value":1.2442,"unit":"in","pm":0.0044,"stated":"1 1/4 -18 UNEF-2A MAJOR DIA - 1.2485/1.2398 (AFTER ANODIZE)","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: plan view, the threaded end; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}},{"id":"photo","value":1.232,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/expo-arms-stripped-upper aad70ef8abd5 (Primary Arms' XP-UPPER_02: the stripped receiver's right side, level, 2200 x 1467)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each bore's near and far edges fitted as circles (rms 0.06 to 0.08 px), their midpoints the frame's points: 256.86 px/in on the receiver's mid-plane; the rail's 13 slots fit the standard pitch to 0.07% on it","method":"the nose's top to its bottom over x 6.7 to 6.9: 1.232; a black thread on white reads thin, its crests' tips lost","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's thread, which its page's \"compatible with standard mil-spec ... handguards, and barrels\" makes this one's; the photo reads 1% under, as a black tube does on white."}},"barrel_thread_minor_d":{"label":"The barrel-nut thread's minor diameter","kind":"length","measurements":[{"id":"tdp","value":1.1803,"unit":"in","pm":0.003,"stated":"MINOR DIA - 1.1803 MAX","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: plan view, the threaded end; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}}]},"barrel_thread_tpi":{"label":"The barrel-nut thread's turns to the inch","kind":"count","measurements":[{"id":"tdp","value":18,"unit":"count","pm":0,"stated":"1 1/4 -18 UNEF-2A","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: plan view, the threaded end; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}}]},"gas_tube_hole_d":{"label":"The gas tube's hole in the front shoulder","kind":"length","measurements":[{"id":"tdp","value":0.1835,"unit":"in","pm":0.0015,"stated":".182 DIA +.003 THRU; .312 DIA +.010 BACK BORE","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 2 of 2, rev G: View F-F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p109","via":"user"}},{"id":"model","value":0.175,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): a cylinder r 0.0875 along x at y 1.662, z 0 (0.783 above the bore), x 6.401 to 6.591","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's callout (D49); the model's hole is 0.008 smaller."},"note":"Above the thread on the bore's mid-plane, std.ar15.gas_tube_above_bore above the bore. Primary Arms' three-quarter photo (5da4e9e47f7d) shows it with four small reliefs at its corners."},"gas_tube_relief_d":{"label":"The gas tube hole's four corner reliefs, diameter","kind":"length","measurements":[{"id":"tdp","value":0.094,"unit":"in","pm":0.002,"stated":".047 R, 4 PLACES EQUALLY SPACED RANDOM ORIENTATION EXCEPT MUST NOT INTERSECT THREADS","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 2 of 2, rev G: View F-F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p109","via":"user"}},{"id":"model","value":0.09,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): four cylinders r 0.0450 along x round the gas tube's hole","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's radius; the model's is 0.002 less."}},"gas_tube_relief_offset":{"label":"The gas tube hole's corner reliefs, off its centre each way","kind":"length","measurements":[{"id":"model","value":0.078,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): their axes at y 1.585 and 1.740, z ±0.078: 0.0775 and 0.078 off the hole's centre","via":"user"}}]},"port_length":{"label":"The ejection port's length","kind":"length","measurements":[{"id":"tdp","value":3.125,"unit":"in","pm":0.005,"stated":"3.125; .25 R TRUE 2 PLACES; 1.562 ±.010","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: side elevation; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}},{"id":"photo","value":3.06,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/expo-arms-stripped-upper aad70ef8abd5 (Primary Arms' XP-UPPER_02: the stripped receiver's right side, level, 2200 x 1467)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each bore's near and far edges fitted as circles (rms 0.06 to 0.08 px), their midpoints the frame's points: 256.86 px/in on the receiver's mid-plane; the rail's 13 slots fit the standard pitch to 0.07% on it","method":"the dark opening from px u 1040 to 1838: 2.980 to 6.088, in the wall 0.55 nearer than the mid-plane: the lens stands about 36 in away opposite x 1.69, y 1.04 (right_photo_lens_*), so what is z nearer than the mid-plane reads large about that point by 36 / (36 - z): 2.960 to 6.020","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The callout, and its page says it \"Accepts Standard Port Cover\"; the brass deflector, added after the port is cut, sets the opening's rear end where the photo shows it."},"note":"The opening reads 0.06 short of the callout, as it does on Aero's photo and on the reference model (3.097): the drawing marks .005 and .042 beside the 3.125's two ends, which may be the opening's own ends inside it."},"port_front_x":{"label":"The ejection port's front end ahead of the takedown pin","kind":"length","measurements":[{"id":"tdp","value":6.036,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{.front_face_x} - 1.00in","via":"user"},"note":"8448524 sheet 1: \"1.00\" from the 3.125's front end to the receiver's front end (read on the scan at 309 px/in: the two extension lines are 1.00 apart)."},{"id":"photo","value":6.02,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/expo-arms-stripped-upper aad70ef8abd5 (Primary Arms' XP-UPPER_02: the stripped receiver's right side, level, 2200 x 1467)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each bore's near and far edges fitted as circles (rms 0.06 to 0.08 px), their midpoints the frame's points: 256.86 px/in on the receiver's mid-plane; the rail's 13 slots fit the standard pitch to 0.07% on it","method":"the opening's front end, px u 1838: 6.088, corrected as port_length","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing; the photo reads 0.016 less, within its ±."}},"port_bottom_y":{"label":"The port's lower edge above the pin line, seen from the side (its ends R .25: 0.50 high)","kind":"length","measurements":[{"id":"drawn","value":0.841,"unit":"in","pm":0.01,"source":{"type":"standard","doc":"8448524 sheet 1 side view, scaled (not a callout): its lower straight edge at px row 3640 against the lug holes' row 3900 at the sheet's own 309.3 px/in (the lug holes 6.375 apart), as aero-m4e1-threaded-upper.port_bottom_y read it; a half-size crop reads 0.847 here","via":"user"}},{"id":"photo","value":0.848,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/expo-arms-stripped-upper aad70ef8abd5 (Primary Arms' XP-UPPER_02: the stripped receiver's right side, level, 2200 x 1467)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each bore's near and far edges fitted as circles (rms 0.06 to 0.08 px), their midpoints the frame's points: 256.86 px/in on the receiver's mid-plane; the rail's 13 slots fit the standard pitch to 0.07% on it","method":"the dark opening's lower edge, px row 758: 0.845, corrected as port_length; its upper edge reads 1.377, the upper wall's inside in the dark","via":"harvest"}}],"adopt":{"from":"drawn","reason":"The drawing's outline at its own scale; the photo agrees within its ±."}},"port_end_r":{"label":"The port's ends' radius (half its height from the side)","kind":"length","measurements":[{"id":"tdp","value":0.25,"unit":"in","pm":0.005,"stated":".25 R TRUE 2 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: side elevation; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}}]},"fa_axis_angle":{"label":"The forward assist's axis, turned inward toward the front in plan","kind":"angle","measurements":[{"id":"tdp","value":20,"unit":"deg","pm":1,"stated":"20°","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: the plan view's forward assist section (CL HOLE at 20°, 1.0285 ±.0050, .509 DIA ±.003, .315 DIA ±.001); user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}}],"note":"The reference model has 22.5 (aero-m4e1-threaded-upper.fa_axis_angle): the drawing wins (D49)."},"fa_bore_d":{"label":"The forward assist's bore","kind":"length","measurements":[{"id":"tdp","value":0.509,"unit":"in","pm":0.003,"stated":".509 DIA ±.003","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: the plan view's forward assist section; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}},{"id":"photo","value":0.517,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/expo-arms-stripped-upper aad70ef8abd5 (Primary Arms' XP-UPPER_02: the stripped receiver's right side, level, 2200 x 1467)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each bore's near and far edges fitted as circles (rms 0.06 to 0.08 px), their midpoints the frame's points: 256.86 px/in on the receiver's mid-plane; the rail's 13 slots fit the standard pitch to 0.07% on it","method":"the bore's rear opening, the dark ellipse px v 678 to 815: 0.533 high, 1.13 nearer than the mid-plane: the lens stands about 36 in away opposite x 1.69, y 1.04 (right_photo_lens_*), so what is z nearer than the mid-plane reads large about that point by 36 / (36 - z)","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's, and its page says it \"Accepts Standard Forward Assist\"; the photo's opening agrees within its ±."}},"fa_bore_depth":{"label":"The forward assist's bore, how deep its .509 runs from the housing's rear face","kind":"length","measurements":[{"id":"tdp","value":0.65,"unit":"in","pm":0.01,"stated":".65","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: the plan view's forward assist section; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}}],"note":"Read as the .509 bore's depth along its axis; ahead of it the hole is the .315."},"fa_inner_bore_d":{"label":"The forward assist's inner bore, ahead of the .509","kind":"length","measurements":[{"id":"tdp","value":0.315,"unit":"in","pm":0.001,"stated":".315 DIA ±.001","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: the plan view's forward assist section; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}}]},"fa_axis_x":{"label":"The forward assist's axis: a point on it, X","kind":"length","measurements":[{"id":"model","value":-0.395,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the r .25 bore's axis through (-0.395, 0.879, 1.090)","via":"user"}}],"note":"With fa_axis_z and the drawing's angle this places the axis; scaled off the drawing's plan view (309 px/in) the hole's centre line is 1.0285 from the receiver's centre line 0.41 ahead of the rear face, which puts it at 1.097 here."},"fa_axis_z":{"label":"The forward assist's axis: that point out from the middle (Z)","kind":"length","measurements":[{"id":"model","value":1.09,"unit":"in","pm":0.01,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the r .25 bore's axis through (-0.395, 0.879, 1.090)","via":"user"}}]},"fa_rear_x":{"label":"The forward assist housing's rear face where the axis crosses it, X","kind":"length","measurements":[{"id":"photo","value":-0.49,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/expo-arms-stripped-upper aad70ef8abd5 (Primary Arms' XP-UPPER_02: the stripped receiver's right side, level, 2200 x 1467)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each bore's near and far edges fitted as circles (rms 0.06 to 0.08 px), their midpoints the frame's points: 256.86 px/in on the receiver's mid-plane; the rail's 13 slots fit the standard pitch to 0.07% on it","method":"the bore's opening, the dark ellipse px u 109 to 152: its centre at -0.559, 1.13 nearer than the mid-plane: the lens stands about 36 in away opposite x 1.69, y 1.04 (right_photo_lens_*), so what is z nearer than the mid-plane reads large about that point by 36 / (36 - z)","via":"harvest"}}],"note":"This receiver's housing runs back to the rear end, as the drawing's side view has it (its opening centred 0.16 ahead of the rear face there); the reference model's stops at -0.34."},"fa_housing_r":{"label":"The forward assist housing's radius about its axis","kind":"length","measurements":[{"id":"model","value":0.3125,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the housing's cylinder r .3125 on the bore's axis","via":"user"}},{"id":"photo","value":0.32,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/expo-arms-stripped-upper aad70ef8abd5 (Primary Arms' XP-UPPER_02: the stripped receiver's right side, level, 2200 x 1467)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each bore's near and far edges fitted as circles (rms 0.06 to 0.08 px), their midpoints the frame's points: 256.86 px/in on the receiver's mid-plane; the rail's 13 slots fit the standard pitch to 0.07% on it","method":"the housing's rear rim, px v 660 to 830: 0.662 high, 1.13 nearer than the mid-plane: the lens stands about 36 in away opposite x 1.69, y 1.04 (right_photo_lens_*), so what is z nearer than the mid-plane reads large about that point by 36 / (36 - z): 0.641 across","via":"harvest"}}],"adopt":{"from":"model","reason":"The forging's; this receiver's photo agrees within its ±."}},"deflector_out":{"label":"The brass deflector's crest, out from the middle (Z; the forging's)","kind":"length","measurements":[{"id":"model","value":1.25,"unit":"in","pm":0.05,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): its crest's faces (a sphere and r .125, r 1.35 cylinders) reach z 1.20 to 1.30 at x 2.31 to 2.34, y 1.11 to 1.32","via":"user"}}],"note":"The mil-spec forging's: no end or top view of this receiver is on file to read its own on."},"deflector_crest_x":{"label":"The deflector's crest, X","kind":"length","measurements":[{"id":"model","value":2.32,"unit":"in","pm":0.02,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): its crest's faces at x 2.308 to 2.337","via":"user"}},{"id":"photo","value":2.334,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/expo-arms-stripped-upper aad70ef8abd5 (Primary Arms' XP-UPPER_02: the stripped receiver's right side, level, 2200 x 1467)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each bore's near and far edges fitted as circles (rms 0.06 to 0.08 px), their midpoints the frame's points: 256.86 px/in on the receiver's mid-plane; the rail's 13 slots fit the standard pitch to 0.07% on it","method":"the crease between its steep rear face and its long slope, px u 870 to 890: 2.357, 1.25 nearer than the mid-plane: the lens stands about 36 in away opposite x 1.69, y 1.04 (right_photo_lens_*), so what is z nearer than the mid-plane reads large about that point by 36 / (36 - z)","via":"harvest"}}],"adopt":{"from":"model","reason":"The model places the crest; this receiver's photo shows it there within its ±."}},"deflector_front_out":{"label":"The deflector's slope where it ends at the port, out from the middle (Z; the forging's)","kind":"length","measurements":[{"id":"model","value":0.82,"unit":"in","pm":0.03,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): its slope's faces come down to z 0.813 at x 2.886","via":"user"}}]},"hinge_axis_y":{"label":"The port door's hinge pin, Y","kind":"length","measurements":[{"id":"model","value":0.641,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the two lugs' r .0625 holes and r .1365 bosses on one axis at y 0.641, z 0.689","via":"user"}}],"note":"This receiver's photo shows its two hinge lugs where the model has them (2.80 to 2.94 and 6.09 to 6.25 once corrected for their depth, against 2.837 to 2.932 and 6.079 to 6.235)."},"hinge_axis_z":{"label":"The port door's hinge pin, out from the middle (Z)","kind":"length","measurements":[{"id":"model","value":0.689,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): as hinge_axis_y","via":"user"}}]},"hinge_boss_r":{"label":"The hinge lugs' radius about the pin","kind":"length","measurements":[{"id":"model","value":0.1365,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the lugs' cylindrical faces r .1365","via":"user"}}]},"hinge_pin_d":{"label":"The hinge pin's hole","kind":"length","measurements":[{"id":"tdp","value":0.1295,"unit":"in","pm":0.0015,"stated":".128 DIA +.003 THRU 2 HOLES IN LINE","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 2 of 2, rev G: Section B-B; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p109","via":"user"}},{"id":"model","value":0.125,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the lugs' holes r .0625","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's callout; the model's holes are 0.004 smaller."}},"cam_pad_face_z":{"label":"The cam pin's pad on the left side, its face out from the middle (Z, to the left)","kind":"length","measurements":[{"id":"model","value":0.5625,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the pad's flat face at z -0.561 to -0.564 over x 4.60 to 5.58, y 1.05 to 1.63","via":"user"}}],"note":"This receiver's left photo shows the pad at x 4.53 to 5.63, y 1.13 to 1.68 once corrected for its depth."}}},{"subject":"faxon-16-pencil-barrel","title":"Faxon Duty Series Pencil Profile 16\" Mid-Length 5.56 NATO AR15 Barrel (15A58M16NPQ)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"faxon","value":1.2,"unit":"lb","pm":0.005,"stated":"Weight 1.20 lb","source":{"type":"spec","publisher":"manufacturer","name":"Faxon Firearms, FAXON DUTY SERIES PENCIL PROFILE 16\" MID-LENGTH 5.56 NATO AR15 BARREL (SKU 15A58M16NPQ), Specifications; its headline: \"4150 CMV | QPQ Nitride | 1:8 Twist | 1.20 lb | SKU: 15A58M16NPQ\"","url":"https://faxonfirearms.com/15A58M16NPQ","retrieved":"2026-10-12","via":"harvest"}},{"id":"primary-arms","value":1.2,"unit":"lb","pm":0.005,"stated":"1.20 lbs weight","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Faxon Firearms 5.56 AR-15 Barrel - Mid-Length - Pencil - 16\" (15A58M16NPQ), Features; its Specifications: \"Weight 1.2 lbs\"","url":"https://www.primaryarms.com/faxon-firearms-5-56-ar-15-barrel-mid-length-pencil-16","retrieved":"2026-10-12","via":"harvest"}},{"id":"wing-tactical","value":19.2,"unit":"oz","pm":0.05,"stated":"16-Inch: 1 lb 3.2 oz.","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Faxon Firearms 5.56 NATO Pencil Barrel (one page for three lengths: MPN 15A58C10NPQ / 15A58M14NPQ / 15A58M16NPQ), Specifications, the 16-Inch line","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/ar-15-barrels/faxon-firearms-5-56-nato-pencil-barrel/","retrieved":"2026-10-12","via":"harvest"}}],"adopt":{"from":"faxon","reason":"The maker's own figure; two sellers state the same weight (19.2 oz is 1.20 lb)."},"note":"Faxon: \"Dimensions are from the Faxon engineering print and inspection sheets for this SKU; weight is nominal.\" The model's volume as steel is the check (app/tests/faxon-16-pencil-barrel.test.ts)."},"length":{"label":"Barrel length as its maker states it","kind":"length","measurements":[{"id":"faxon","value":16.13,"unit":"in","pm":0.005,"stated":"Length 16.13″ (16″ nominal)","source":{"type":"spec","publisher":"manufacturer","name":"Faxon Firearms, FAXON DUTY SERIES PENCIL PROFILE 16\" MID-LENGTH 5.56 NATO AR15 BARREL (SKU 15A58M16NPQ), Specifications","url":"https://faxonfirearms.com/15A58M16NPQ","retrieved":"2026-10-12","via":"harvest"}},{"id":"primary-arms","value":16,"unit":"in","pm":0.5,"stated":"Barrel Length 16","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Faxon Firearms 5.56 AR-15 Barrel - Mid-Length - Pencil - 16\" (15A58M16NPQ), Specifications","url":"https://www.primaryarms.com/faxon-firearms-5-56-ar-15-barrel-mid-length-pencil-16","retrieved":"2026-10-12","via":"harvest"},"note":"The nominal length, to the inch."}],"adopt":{"from":"faxon","reason":"The maker's own, to the hundredth; the seller states the nominal 16."},"note":"Faxon states it to the hundredth and calls 16 in the nominal. Between which points isn't said: with the extension's standard half inch behind the barrel's breech end (overall_length), Primary Arms' side photo has the published .625 journal at .6251, the published 1.1 in journal at 1.113 and the published .625 in of thread at .6255, so the 16.13 is taken from the barrel's breech end, inside the extension, to the muzzle (as the Army's drawing dimensions a barrel). Taken from the extension's rear end or from the receiver's face the three would read 3% large or 2% small."},"journal_od":{"label":"The gas block journal's diameter","kind":"length","measurements":[{"id":"faxon","value":0.625,"unit":"in","pm":0.001,"stated":"Gas journal .625″ (.6240–.6247″), 1.1″ long, held within .005″ of the bore","source":{"type":"spec","publisher":"manufacturer","name":"Faxon Firearms, FAXON DUTY SERIES PENCIL PROFILE 16\" MID-LENGTH 5.56 NATO AR15 BARREL (SKU 15A58M16NPQ), Specifications","url":"https://faxonfirearms.com/15A58M16NPQ","retrieved":"2026-10-12","via":"harvest"}},{"id":"primary-arms","value":0.625,"unit":"in","pm":0.0005,"stated":".625\" gas seat diameter","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Faxon Firearms 5.56 AR-15 Barrel - Mid-Length - Pencil - 16\" (15A58M16NPQ), Features; its Specifications: \"Gas Seat Diameter .625\"","url":"https://www.primaryarms.com/faxon-firearms-5-56-ar-15-barrel-mid-length-pencil-16","retrieved":"2026-10-12","via":"harvest"}},{"id":"impact-guns","value":0.625,"unit":"in","pm":0.0005,"stated":"Gas Block Diameter : .625\"","source":{"type":"spec","publisher":"retailer","name":"Impact Guns, Faxon Firearms Duty Series, 1:8 Twist Barrel, 5.56mm, 16\" Pencil Profile (manufacturer number 15A58M16NPQ), Features","url":"https://www.impactguns.com/Barrels/Faxon-Barrel-16-Pencil-5-56-Nato-Mid-Length-4150-Qpq-816341020146-15A58M16NPQ/","retrieved":"2026-10-12","via":"harvest"}}],"adopt":{"from":"faxon","reason":"The maker's own, with the limits it is turned to; two sellers state the same."},"note":"The catalog's first .625 journal. Faxon: \"the .625″ gas journal is turned to .6240–.6247″ and checked with a micrometer on every barrel\"."},"journal_length":{"label":"The gas block journal's length","kind":"length","measurements":[{"id":"faxon","value":1.1,"unit":"in","pm":0.05,"stated":"Gas journal .625″ (.6240–.6247″), 1.1″ long, held within .005″ of the bore","source":{"type":"spec","publisher":"manufacturer","name":"Faxon Firearms, FAXON DUTY SERIES PENCIL PROFILE 16\" MID-LENGTH 5.56 NATO AR15 BARREL (SKU 15A58M16NPQ), Specifications","url":"https://faxonfirearms.com/15A58M16NPQ","retrieved":"2026-10-12","via":"harvest"}},{"id":"primary-arms","value":1.1,"unit":"in","pm":0.05,"stated":"1.1\" gas block journal","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Faxon Firearms 5.56 AR-15 Barrel - Mid-Length - Pencil - 16\" (15A58M16NPQ), Features","url":"https://www.primaryarms.com/faxon-firearms-5-56-ar-15-barrel-mid-length-pencil-16","retrieved":"2026-10-12","via":"harvest"}},{"id":"impact-guns","value":1.1,"unit":"in","pm":0.05,"stated":"Gas Block Journal Length : 1.1\"","source":{"type":"spec","publisher":"retailer","name":"Impact Guns, Faxon Firearms Duty Series, 1:8 Twist Barrel, 5.56mm, 16\" Pencil Profile (manufacturer number 15A58M16NPQ), Features","url":"https://www.impactguns.com/Barrels/Faxon-Barrel-16-Pencil-5-56-Nato-Mid-Length-4150-Qpq-816341020146-15A58M16NPQ/","retrieved":"2026-10-12","via":"harvest"}},{"id":"photo","value":1.113,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.journal_front_x} - {.journal_rear_x}","via":"harvest"},"note":"Primary Arms' side photo: the collar's front face to where the barrel begins to narrow."}],"adopt":{"from":"faxon","reason":"The maker's own; two sellers state it and the photo reads it within a hundredth and a half."},"note":"What a gas block has to fit on: Faxon, \"use a block 1″ long or shorter\". The model takes the journal's two ends where the photo has them (journal_rear_x, journal_front_x), 1.113 apart."},"gas_port_d":{"label":"The gas port's diameter","kind":"length","measurements":[{"id":"faxon","value":0.081,"unit":"in","pm":0.0005,"stated":"Gas system Mid-length; .081″ port, reamed to size","source":{"type":"spec","publisher":"manufacturer","name":"Faxon Firearms, FAXON DUTY SERIES PENCIL PROFILE 16\" MID-LENGTH 5.56 NATO AR15 BARREL (SKU 15A58M16NPQ), Specifications; its FAQ: \"The gas port is reamed to .081″.\"","url":"https://faxonfirearms.com/15A58M16NPQ","retrieved":"2026-10-12","via":"harvest"}},{"id":"primary-arms","value":0.078,"unit":"in","pm":0.0005,"stated":".625\" gas seat diameter, .078\" gas port, 1.1\" gas block journal","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Faxon Firearms 5.56 AR-15 Barrel - Mid-Length - Pencil - 16\" (15A58M16NPQ), Features","url":"https://www.primaryarms.com/faxon-firearms-5-56-ar-15-barrel-mid-length-pencil-16","retrieved":"2026-10-12","via":"harvest"}},{"id":"impact-guns","value":0.078,"unit":"in","pm":0.0005,"stated":"Gas Port Diameter : .078\"","source":{"type":"spec","publisher":"retailer","name":"Impact Guns, Faxon Firearms Duty Series, 1:8 Twist Barrel, 5.56mm, 16\" Pencil Profile (manufacturer number 15A58M16NPQ), Features","url":"https://www.impactguns.com/Barrels/Faxon-Barrel-16-Pencil-5-56-Nato-Mid-Length-4150-Qpq-816341020146-15A58M16NPQ/","retrieved":"2026-10-12","via":"harvest"}}],"adopt":{"from":"faxon","reason":"The maker's own page, which says the figure is from its engineering print and states it three times; the two sellers' .078 is one feed's figure (their feature lists are the same list) and may be an earlier revision's. Three thousandths: nothing drawn or checked turns on it."},"note":"Faxon's own page against two sellers' pages: .081 and .078. Both stay. Faxon: \"Bore, groove, journal, and port figures are from the Faxon engineering print and inspection sheets for this SKU.\" and \"After nitride, the .081″ gas port is drilled and reamed through the .625″ journal\"."},"extension_behind_breech":{"label":"The barrel extension's rear end behind the barrel's breech end","kind":"length","measurements":[{"id":"model","value":0.501,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{std.ar15.barrel_extension_behind_breech}","via":"user"}}],"note":"The standard's: the reference CAD set's extension less the Army's .620 tenon (std.ar15.barrel_extension_behind_breech, where both readings and their sources are). Faxon: \"M4 feed-ramp barrel extension, black oxide, installed at 150 ft-lb, pinned, and headspaced\": a standard extension."},"overall_length":{"label":"End to end, the extension's rear to the muzzle","kind":"length","measurements":[{"id":"photo","value":16.63,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/faxon-16-pencil-barrel f09ad3b5be48 (Primary Arms' gallery, 15A58M16NPQ_01: the barrel level on white, the muzzle at the right, the index pin and the gas port on top, 2000 x 1333)","scaleRef":"its gas block journal, 68.45 px across (columns 1170 to 1284, the silhouette at grey 235), as the published .625 (journal_od): 109.52 px/in","method":"its two end faces, each where its rim arc reaches the full height: the rear end at column 87.7 (the tip at 76, a 12 px arc on a radius of 54: the lens saw that end from 12.5° off square), the muzzle at 1909.0 (the tip at 1914.7, a 6 px arc on 26.6: 12°): 1821.3 px. The ± covers a pixel at each face and a pixel of the journal's edges","via":"harvest"}},{"id":"published","value":16.631,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{.length} + {.extension_behind_breech}","via":"harvest"}}],"adopt":{"from":"published","reason":"Lengths at the published length's scale, as the catalog's other barrels; the photo by its journal reads the same within a thousandth."},"note":"The published length with the standard extension's half inch behind the breech; the photo's own reading, scaled by its journal's published diameter, is the same within a thousandth (the silhouette read at grey 235, where a black part's lit edge is: CLAUDE.md)."},"extension_rear_x":{"label":"The barrel extension's rear end, from the flange's rear face (negative: inside the receiver)","kind":"length","measurements":[{"id":"photo","value":-0.976,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/faxon-16-pencil-barrel f09ad3b5be48 (Primary Arms' gallery, 15A58M16NPQ_01: the barrel level on white, the muzzle at the right, the index pin and the gas port on top, 2000 x 1333)","scaleRef":"its end faces, 1821.3 px apart (columns 87.7 and 1909.0: where each end's rim arc reaches the full height, the silhouette at grey 235 of 255), as overall_length (16.631): 109.51 px/in. At that scale the gas block journal reads .6251 across (68.45 px over columns 1170 to 1284; published .625), 1.113 long (published 1.1) and the thread .6255 long (published .625): one scale for lengths and diameters","method":"the rear end's face (column 87.7) to the flange's rear face (column 194.6: where the flange's rim arc, seen past the extension's body over columns 188 to 194, reaches its full height)","via":"harvest"}}],"note":"The reference CAD set's extension has 0.990 here (1.121 less its 0.131 flange); BCM's reads 0.984 and Geissele's 1.001 by their photos."},"flange_front_x":{"label":"The extension flange's front face, ahead of its rear face (the flange's thickness)","kind":"length","measurements":[{"id":"photo","value":0.109,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/faxon-16-pencil-barrel f09ad3b5be48 (Primary Arms' gallery, 15A58M16NPQ_01: the barrel level on white, the muzzle at the right, the index pin and the gas port on top, 2000 x 1333)","scaleRef":"its end faces, 1821.3 px apart (columns 87.7 and 1909.0: where each end's rim arc reaches the full height, the silhouette at grey 235 of 255), as overall_length (16.631): 109.51 px/in. At that scale the gas block journal reads .6251 across (68.45 px over columns 1170 to 1284; published .625), 1.113 long (published 1.1) and the thread .6255 long (published .625): one scale for lengths and diameters","method":"the flange's rear face (column 194.6: where the flange's rim arc, seen past the extension's body over columns 188 to 194, reaches its full height) to where the flange's edge stops being level (column 206.5)","via":"harvest"}}],"note":"The reference CAD set's flange is 0.131 thick; BCM's reads 0.095 and Geissele's 0.117. Ahead of the face the silhouette's corner is the rim's far arc, seen past the barrel (to column 213)."},"flange_od":{"label":"The barrel extension's flange, its diameter","kind":"length","measurements":[{"id":"photo","value":1.163,"unit":"in","pm":0.009,"source":{"type":"photo","photo":"references/faxon-16-pencil-barrel f09ad3b5be48 (Primary Arms' gallery, 15A58M16NPQ_01: the barrel level on white, the muzzle at the right, the index pin and the gas port on top, 2000 x 1333)","scaleRef":"its end faces, 1821.3 px apart (columns 87.7 and 1909.0: where each end's rim arc reaches the full height, the silhouette at grey 235 of 255), as overall_length (16.631): 109.51 px/in. At that scale the gas block journal reads .6251 across (68.45 px over columns 1170 to 1284; published .625), 1.113 long (published 1.1) and the thread .6255 long (published .625): one scale for lengths and diameters","method":"the silhouette's widest, columns 195 to 206: 127.4 px. The ± is a pixel","via":"harvest"}}],"note":"The silhouette's greatest height, and the traced outline's scale reference. The reference CAD set's flange is 1.170."},"extension_od":{"label":"The barrel extension's body, its diameter (what goes into the receiver)","kind":"length","measurements":[{"id":"tdp","value":0.999,"unit":"in","pm":0.001,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_od}","via":"user"},"note":"The Army's limit on the assembly drawing (8448548: \"DIAMETER NOT TO EXCEED .9990 FOR THIS LENGTH AFTER ASSEMBLY AND BEFORE FINISH\"), as read for BCM's barrel's ledger, where the drawing and its page are cited."},{"id":"photo","value":0.984,"unit":"in","pm":0.009,"source":{"type":"photo","photo":"references/faxon-16-pencil-barrel f09ad3b5be48 (Primary Arms' gallery, 15A58M16NPQ_01: the barrel level on white, the muzzle at the right, the index pin and the gas port on top, 2000 x 1333)","scaleRef":"its end faces, 1821.3 px apart (columns 87.7 and 1909.0: where each end's rim arc reaches the full height, the silhouette at grey 235 of 255), as overall_length (16.631): 109.51 px/in. At that scale the gas block journal reads .6251 across (68.45 px over columns 1170 to 1284; published .625), 1.113 long (published 1.1) and the thread .6255 long (published .625): one scale for lengths and diameters","method":"the extension's body, columns 90 to 172: 107.75 px. The ± is a pixel","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's limit: the extension goes into a receiver's 1.000 bore. The photo reads a glossy black round a pixel and a half thin."},"note":"The photo's reading is 1.5% under the drawing's limit: the extension is black oxide (Faxon), glossier than the nitrided barrel, and a glossy black round reads thin on white (CLAUDE.md). The drawing's figure is what goes into a receiver."},"chamber_od":{"label":"The chamber journal's diameter, ahead of the flange","kind":"length","measurements":[{"id":"faxon","value":0.98,"unit":"in","pm":0.0005,"stated":"Profile Pencil: .980″ chamber journal, tapered body behind the gas block, .625″ journal (1.1″ long), tapered from .625″ to .525″ ahead of it, .615″ muzzle shoulder","source":{"type":"spec","publisher":"manufacturer","name":"Faxon Firearms, FAXON DUTY SERIES PENCIL PROFILE 16\" MID-LENGTH 5.56 NATO AR15 BARREL (SKU 15A58M16NPQ), Specifications","url":"https://faxonfirearms.com/15A58M16NPQ","retrieved":"2026-10-12","via":"harvest"}},{"id":"photo","value":0.973,"unit":"in","pm":0.009,"source":{"type":"photo","photo":"references/faxon-16-pencil-barrel f09ad3b5be48 (Primary Arms' gallery, 15A58M16NPQ_01: the barrel level on white, the muzzle at the right, the index pin and the gas port on top, 2000 x 1333)","scaleRef":"its end faces, 1821.3 px apart (columns 87.7 and 1909.0: where each end's rim arc reaches the full height, the silhouette at grey 235 of 255), as overall_length (16.631): 109.51 px/in. At that scale the gas block journal reads .6251 across (68.45 px over columns 1170 to 1284; published .625), 1.113 long (published 1.1) and the thread .6255 long (published .625): one scale for lengths and diameters","method":"the section ahead of the flange, columns 216 to 280: 106.5 px. The ± is a pixel","via":"harvest"}}],"adopt":{"from":"faxon","reason":"The maker's figure, from its print; the photo reads it within a pixel."},"note":"Faxon: \"a .980″ chamber journal for the extension and barrel nut\". The Faxon shield is lasered on it."},"chamber_front_x":{"label":"Where the chamber journal ends and the barrel begins to narrow, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":0.794,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/faxon-16-pencil-barrel f09ad3b5be48 (Primary Arms' gallery, 15A58M16NPQ_01: the barrel level on white, the muzzle at the right, the index pin and the gas port on top, 2000 x 1333)","scaleRef":"its end faces, 1821.3 px apart (columns 87.7 and 1909.0: where each end's rim arc reaches the full height, the silhouette at grey 235 of 255), as overall_length (16.631): 109.51 px/in. At that scale the gas block journal reads .6251 across (68.45 px over columns 1170 to 1284; published .625), 1.113 long (published 1.1) and the thread .6255 long (published .625): one scale for lengths and diameters","method":"the flange's rear face (column 194.6: where the flange's rim arc, seen past the extension's body over columns 188 to 194, reaches its full height) to where the edges leave the level (column 281.5: 106.5 px at 281, 105.9 at 283, then 0.354 px of height a column)","via":"harvest"}}]},"taper_rear_x":{"label":"Where the cone ahead of the chamber journal ends and the long taper begins, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":1.798,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/faxon-16-pencil-barrel f09ad3b5be48 (Primary Arms' gallery, 15A58M16NPQ_01: the barrel level on white, the muzzle at the right, the index pin and the gas port on top, 2000 x 1333)","scaleRef":"its end faces, 1821.3 px apart (columns 87.7 and 1909.0: where each end's rim arc reaches the full height, the silhouette at grey 235 of 255), as overall_length (16.631): 109.51 px/in. At that scale the gas block journal reads .6251 across (68.45 px over columns 1170 to 1284; published .625), 1.113 long (published 1.1) and the thread .6255 long (published .625): one scale for lengths and diameters","method":"the flange's rear face (column 194.6: where the flange's rim arc, seen past the extension's body over columns 188 to 194, reaches its full height) to where the cone's line meets the long taper's (column 391.5; the corner is blended over 6 px)","via":"harvest"}}],"note":"The cone is straight: 0.354 px of height a column from column 283 to 386, 10° a side."},"taper_rear_od":{"label":"The long taper's diameter at its rear end (the body's thickest behind the gas block)","kind":"length","measurements":[{"id":"photo","value":0.618,"unit":"in","pm":0.009,"source":{"type":"photo","photo":"references/faxon-16-pencil-barrel f09ad3b5be48 (Primary Arms' gallery, 15A58M16NPQ_01: the barrel level on white, the muzzle at the right, the index pin and the gas port on top, 2000 x 1333)","scaleRef":"its end faces, 1821.3 px apart (columns 87.7 and 1909.0: where each end's rim arc reaches the full height, the silhouette at grey 235 of 255), as overall_length (16.631): 109.51 px/in. At that scale the gas block journal reads .6251 across (68.45 px over columns 1170 to 1284; published .625), 1.113 long (published 1.1) and the thread .6255 long (published .625): one scale for lengths and diameters","method":"the body at column 396: 67.65 px. The taper is straight: 62.9 px at column 752 where a line between its two ends has 62.6. The ± is a pixel","via":"harvest"}}],"note":"Faxon names the taper and gives it no figures: \"tapered body behind the gas block\"."},"taper_front_x":{"label":"Where the long taper ends and the barrel rises to the gas block's collar, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":8.377,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/faxon-16-pencil-barrel f09ad3b5be48 (Primary Arms' gallery, 15A58M16NPQ_01: the barrel level on white, the muzzle at the right, the index pin and the gas port on top, 2000 x 1333)","scaleRef":"its end faces, 1821.3 px apart (columns 87.7 and 1909.0: where each end's rim arc reaches the full height, the silhouette at grey 235 of 255), as overall_length (16.631): 109.51 px/in. At that scale the gas block journal reads .6251 across (68.45 px over columns 1170 to 1284; published .625), 1.113 long (published 1.1) and the thread .6255 long (published .625): one scale for lengths and diameters","method":"the flange's rear face (column 194.6: where the flange's rim arc, seen past the extension's body over columns 188 to 194, reaches its full height) to where the edges begin to rise (column 1112: 57.5 px to there, 58.4 at 1116)","via":"harvest"}}]},"taper_front_od":{"label":"The long taper's diameter at its front end (the barrel's thinnest behind the gas block)","kind":"length","measurements":[{"id":"photo","value":0.525,"unit":"in","pm":0.009,"source":{"type":"photo","photo":"references/faxon-16-pencil-barrel f09ad3b5be48 (Primary Arms' gallery, 15A58M16NPQ_01: the barrel level on white, the muzzle at the right, the index pin and the gas port on top, 2000 x 1333)","scaleRef":"its end faces, 1821.3 px apart (columns 87.7 and 1909.0: where each end's rim arc reaches the full height, the silhouette at grey 235 of 255), as overall_length (16.631): 109.51 px/in. At that scale the gas block journal reads .6251 across (68.45 px over columns 1170 to 1284; published .625), 1.113 long (published 1.1) and the thread .6255 long (published .625): one scale for lengths and diameters","method":"the body over columns 1100 to 1112: 57.5 px. The ± is a pixel","via":"harvest"}},{"id":"faxon-photo","value":0.525,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/faxon-16-pencil-barrel 3df1d139cab4 (Faxon's own gallery, 15A58M16NPQ-01: the barrel from the side on white, the muzzle at the right, two award badges under it, 2000 x 2000)","scaleRef":"its gas block journal, 59.1 px across (columns 1154 to 1250, the silhouette at grey 235), as the published .625: 94.6 px/in","method":"the body over columns 1082 to 1094: 49.7 to 50.0 px against the journal's 59.1","via":"harvest"}}],"adopt":{"from":"photo","reason":"The larger photograph; the maker's own picture reads the same."},"note":"Here, just behind the collar, is where the photo has the .525 that Faxon's sentence puts ahead of the gas block (see forward_od)."},"collar_od":{"label":"The collar behind the gas block journal, its diameter","kind":"length","measurements":[{"id":"photo","value":0.755,"unit":"in","pm":0.009,"source":{"type":"photo","photo":"references/faxon-16-pencil-barrel f09ad3b5be48 (Primary Arms' gallery, 15A58M16NPQ_01: the barrel level on white, the muzzle at the right, the index pin and the gas port on top, 2000 x 1333)","scaleRef":"its end faces, 1821.3 px apart (columns 87.7 and 1909.0: where each end's rim arc reaches the full height, the silhouette at grey 235 of 255), as overall_length (16.631): 109.51 px/in. At that scale the gas block journal reads .6251 across (68.45 px over columns 1170 to 1284; published .625), 1.113 long (published 1.1) and the thread .6255 long (published .625): one scale for lengths and diameters","method":"the collar, columns 1145 to 1162: 82.65 px. The ± is a pixel","via":"harvest"}},{"id":"faxon-photo","value":0.751,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/faxon-16-pencil-barrel 3df1d139cab4 (Faxon's own gallery, 15A58M16NPQ-01: the barrel from the side on white, the muzzle at the right, two award badges under it, 2000 x 2000)","scaleRef":"its gas block journal, 59.1 px across (columns 1154 to 1250, the silhouette at grey 235), as the published .625: 94.6 px/in","method":"the collar, columns 1128 to 1144: 71.0 px against the journal's 59.1","via":"harvest"}}],"adopt":{"from":"photo","reason":"The larger photograph; the maker's own picture reads the same within its ±."},"note":"A gas block's rear face comes back to it. Faxon's profile sentence for this barrel names no collar; both its own picture and Primary Arms' show one (Faxon's sentence for the Gunner profile has \".750″ step\" behind the same journal: another part, whose figures aren't this one's)."},"collar_rear_x":{"label":"Where the collar's full diameter begins, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":8.668,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/faxon-16-pencil-barrel f09ad3b5be48 (Primary Arms' gallery, 15A58M16NPQ_01: the barrel level on white, the muzzle at the right, the index pin and the gas port on top, 2000 x 1333)","scaleRef":"its end faces, 1821.3 px apart (columns 87.7 and 1909.0: where each end's rim arc reaches the full height, the silhouette at grey 235 of 255), as overall_length (16.631): 109.51 px/in. At that scale the gas block journal reads .6251 across (68.45 px over columns 1170 to 1284; published .625), 1.113 long (published 1.1) and the thread .6255 long (published .625): one scale for lengths and diameters","method":"the flange's rear face (column 194.6: where the flange's rim arc, seen past the extension's body over columns 188 to 194, reaches its full height) to where the collar reaches its full height (column 1143.8)","via":"harvest"}}],"note":"Behind it the barrel rises to the collar along a concave arc (a round-nosed tool's): 31.9 px long for 12.6 px of radius, a radius of 0.43 in. The two other arcs of the profile (ahead of the journal, behind the muzzle ring) have the same radius within 1%."},"journal_rear_x":{"label":"The gas block journal's rear shoulder (the collar's front face) ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":8.847,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/faxon-16-pencil-barrel f09ad3b5be48 (Primary Arms' gallery, 15A58M16NPQ_01: the barrel level on white, the muzzle at the right, the index pin and the gas port on top, 2000 x 1333)","scaleRef":"its end faces, 1821.3 px apart (columns 87.7 and 1909.0: where each end's rim arc reaches the full height, the silhouette at grey 235 of 255), as overall_length (16.631): 109.51 px/in. At that scale the gas block journal reads .6251 across (68.45 px over columns 1170 to 1284; published .625), 1.113 long (published 1.1) and the thread .6255 long (published .625): one scale for lengths and diameters","method":"the flange's rear face (column 194.6: where the flange's rim arc, seen past the extension's body over columns 188 to 194, reaches its full height) to the collar's front face (column 1163.4: 82.2 px at 1163, 72.5 at 1164)","via":"harvest"}}],"note":"BCM's 16 in barrel has it at 8.848, Bear Creek's at 8.85, Aero's at 8.87: the same mid-length place. At the collar's foot the journal has a relief 0.03 in wide and 0.011 deep (66.1 px at column 1165 for the journal's 68.45), a dark line in Primary Arms' close view; it isn't drawn."},"gas_port_x":{"label":"The gas port ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":9.137,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/faxon-16-pencil-barrel d191b524e842 (Primary Arms' gallery, 15A58M16NPQ_03: the gas block journal close up from above its muzzle side, the port toward the lens, 2000 x 1333)","scaleRef":"the journal's own length on the same line, 334 px, as the side photo's 1.113 in (journal_front_x less journal_rear_x): 300 px/in along the barrel","method":"the middle of the port's mouth, 87 px ahead of the collar's front face (the far wall of the relief at its foot) on the line through the port along the barrel (33.6° in the picture), where the journal is 334 px long on that line to the step ahead of it: 0.290 of journal_length as the side photo has it (1.113), ahead of journal_rear_x (8.847). The ± covers the port's mouth (27 px long, its near wall in shadow) and which edge of the relief is the face","via":"harvest"}}],"note":"Faxon gives no distance (\"it puts the port about two inches farther from the chamber than carbine-length gas\"). The port is on top, in line with the index pin and the marking; it doesn't break the side photo's edge, so its place is read on Primary Arms' close view of the journal, along the line through it parallel to the barrel: 0.29 ahead of the collar's face (the Army's rifle barrel has .295, 8448548; BCM's reads 0.28). Checks: BCM's port is at 9.13, Bear Creek's at 9.14, Aero's at 9.17; a mid-length chart's at 9.18."},"journal_front_x":{"label":"The gas block journal's front end (where the barrel begins to narrow) ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":9.96,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/faxon-16-pencil-barrel f09ad3b5be48 (Primary Arms' gallery, 15A58M16NPQ_01: the barrel level on white, the muzzle at the right, the index pin and the gas port on top, 2000 x 1333)","scaleRef":"its end faces, 1821.3 px apart (columns 87.7 and 1909.0: where each end's rim arc reaches the full height, the silhouette at grey 235 of 255), as overall_length (16.631): 109.51 px/in. At that scale the gas block journal reads .6251 across (68.45 px over columns 1170 to 1284; published .625), 1.113 long (published 1.1) and the thread .6255 long (published .625): one scale for lengths and diameters","method":"the flange's rear face (column 194.6: where the flange's rim arc, seen past the extension's body over columns 188 to 194, reaches its full height) to where the edges leave the journal's level (column 1285.3: 68.4 px to 1284, 67.5 at 1286)","via":"harvest"}}]},"forward_rear_x":{"label":"Where the arc ahead of the journal ends and the forward section begins, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":10.181,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/faxon-16-pencil-barrel f09ad3b5be48 (Primary Arms' gallery, 15A58M16NPQ_01: the barrel level on white, the muzzle at the right, the index pin and the gas port on top, 2000 x 1333)","scaleRef":"its end faces, 1821.3 px apart (columns 87.7 and 1909.0: where each end's rim arc reaches the full height, the silhouette at grey 235 of 255), as overall_length (16.631): 109.51 px/in. At that scale the gas block journal reads .6251 across (68.45 px over columns 1170 to 1284; published .625), 1.113 long (published 1.1) and the thread .6255 long (published .625): one scale for lengths and diameters","method":"the flange's rear face (column 194.6: where the flange's rim arc, seen past the extension's body over columns 188 to 194, reaches its full height) to where the edges become level (column 1309.5: 55.1 px at 1309, 54.8 from 1312)","via":"harvest"}}],"note":"Faxon: \"the forward taper is turned from .625″ to .525″\". In the photo it is a concave arc 24 px long, steepest at the journal and running out level into the forward section: a radius of 0.43 in."},"forward_od":{"label":"The forward section's diameter, between the journal and the ring behind the muzzle shoulder","kind":"length","measurements":[{"id":"faxon","value":0.525,"unit":"in","pm":0.0005,"stated":"Profile Pencil: .980″ chamber journal, tapered body behind the gas block, .625″ journal (1.1″ long), tapered from .625″ to .525″ ahead of it, .615″ muzzle shoulder","source":{"type":"spec","publisher":"manufacturer","name":"Faxon Firearms, FAXON DUTY SERIES PENCIL PROFILE 16\" MID-LENGTH 5.56 NATO AR15 BARREL (SKU 15A58M16NPQ), Specifications; its FAQ: \"a .625″ gas journal with the body tapered on both sides of it, down to .525″ ahead of the block\"","url":"https://faxonfirearms.com/15A58M16NPQ","retrieved":"2026-10-12","via":"harvest"}},{"id":"photo","value":0.502,"unit":"in","pm":0.009,"source":{"type":"photo","photo":"references/faxon-16-pencil-barrel f09ad3b5be48 (Primary Arms' gallery, 15A58M16NPQ_01: the barrel level on white, the muzzle at the right, the index pin and the gas port on top, 2000 x 1333)","scaleRef":"its end faces, 1821.3 px apart (columns 87.7 and 1909.0: where each end's rim arc reaches the full height, the silhouette at grey 235 of 255), as overall_length (16.631): 109.51 px/in. At that scale the gas block journal reads .6251 across (68.45 px over columns 1170 to 1284; published .625), 1.113 long (published 1.1) and the thread .6255 long (published .625): one scale for lengths and diameters","method":"the level section ahead of the journal, columns 1312 to 1800: 54.94 px (54.7 to 55.3 along it). The ± is a pixel","via":"harvest"}},{"id":"faxon-photo","value":0.508,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/faxon-16-pencil-barrel 3df1d139cab4 (Faxon's own gallery, 15A58M16NPQ-01: the barrel from the side on white, the muzzle at the right, two award badges under it, 2000 x 2000)","scaleRef":"its gas block journal, 59.1 px across (columns 1154 to 1250, the silhouette at grey 235), as the published .625: 94.6 px/in","method":"the level section ahead of the journal, columns 1274 to 1694: 47.5 px rising to 48.7 (the muzzle a little nearer the lens) against the journal's 59.1","via":"harvest"}}],"adopt":{"from":"photo","reason":"Two photographs of this number, the maker's own among them, show a level section of .50 where the sentence has a taper to .525, and show the .525 behind the collar; the larger photograph's reading is drawn. The maker's sentence stays beside it."},"note":"A CONFLICT, kept: Faxon's sentence has the barrel \"tapered from .625″ to .525″ ahead of\" the journal (and its FAQ: \"down to .525″ ahead of the block\"); both photographs of this number on file, the maker's own and Primary Arms', have a level section ahead of the journal that reads .50, and have the .525 just behind the collar, at the long taper's thin end (taper_front_od). At .525 the section would be 57.5 px across in Primary Arms' photo, where it is 54.8 to 55.1 over five hundred columns, between a journal (.625) and a muzzle shoulder (.615) that read within a pixel of their published figures either side of it. Faxon's sentence for its Gunner profile has \".500″ ahead of\" the same journal. As steel the model weighs 4% over the published 1.20 lb with this section at .50 (19.96 oz) and 6% over with it at .525 (its chamber isn't cut, which is 2% of it, and the steel's density is known to 2%): the weight leans to the photographs' figure and doesn't settle it. The photograph's figure is drawn; a tenth of a pixel on the page either way."},"muzzle_ring_foot_x":{"label":"Where the forward section ends and the barrel rises to the ring behind the muzzle shoulder, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":14.704,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/faxon-16-pencil-barrel f09ad3b5be48 (Primary Arms' gallery, 15A58M16NPQ_01: the barrel level on white, the muzzle at the right, the index pin and the gas port on top, 2000 x 1333)","scaleRef":"its end faces, 1821.3 px apart (columns 87.7 and 1909.0: where each end's rim arc reaches the full height, the silhouette at grey 235 of 255), as overall_length (16.631): 109.51 px/in. At that scale the gas block journal reads .6251 across (68.45 px over columns 1170 to 1284; published .625), 1.113 long (published 1.1) and the thread .6255 long (published .625): one scale for lengths and diameters","method":"the flange's rear face (column 194.6: where the flange's rim arc, seen past the extension's body over columns 188 to 194, reaches its full height) to where the edges begin to rise (column 1804.8: 54.8 px to 1803, 55.2 at 1806)","via":"harvest"}}]},"muzzle_ring_rear_x":{"label":"The rear end of the ring behind the muzzle shoulder (where it reaches its full diameter), ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":14.917,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/faxon-16-pencil-barrel f09ad3b5be48 (Primary Arms' gallery, 15A58M16NPQ_01: the barrel level on white, the muzzle at the right, the index pin and the gas port on top, 2000 x 1333)","scaleRef":"its end faces, 1821.3 px apart (columns 87.7 and 1909.0: where each end's rim arc reaches the full height, the silhouette at grey 235 of 255), as overall_length (16.631): 109.51 px/in. At that scale the gas block journal reads .6251 across (68.45 px over columns 1170 to 1284; published .625), 1.113 long (published 1.1) and the thread .6255 long (published .625): one scale for lengths and diameters","method":"the flange's rear face (column 194.6: where the flange's rim arc, seen past the extension's body over columns 188 to 194, reaches its full height) to where the ring reaches its full height (column 1828.2)","via":"harvest"}}],"note":"The rise is a concave arc again: 23.4 px long for 6.2 of radius to the published .615 (6.6 to the photo's .622), 0.43 in."},"muzzle_od":{"label":"The diameter behind the muzzle thread","kind":"length","measurements":[{"id":"faxon","value":0.615,"unit":"in","pm":0.0005,"stated":"Profile Pencil: .980″ chamber journal, tapered body behind the gas block, .625″ journal (1.1″ long), tapered from .625″ to .525″ ahead of it, .615″ muzzle shoulder","source":{"type":"spec","publisher":"manufacturer","name":"Faxon Firearms, FAXON DUTY SERIES PENCIL PROFILE 16\" MID-LENGTH 5.56 NATO AR15 BARREL (SKU 15A58M16NPQ), Specifications","url":"https://faxonfirearms.com/15A58M16NPQ","retrieved":"2026-10-12","via":"harvest"}},{"id":"photo","value":0.622,"unit":"in","pm":0.009,"source":{"type":"photo","photo":"references/faxon-16-pencil-barrel f09ad3b5be48 (Primary Arms' gallery, 15A58M16NPQ_01: the barrel level on white, the muzzle at the right, the index pin and the gas port on top, 2000 x 1333)","scaleRef":"its end faces, 1821.3 px apart (columns 87.7 and 1909.0: where each end's rim arc reaches the full height, the silhouette at grey 235 of 255), as overall_length (16.631): 109.51 px/in. At that scale the gas block journal reads .6251 across (68.45 px over columns 1170 to 1284; published .625), 1.113 long (published 1.1) and the thread .6255 long (published .625): one scale for lengths and diameters","method":"the ring behind the shoulder, columns 1829 to 1840: 68.1 px. The ± is a pixel","via":"harvest"}}],"adopt":{"from":"faxon","reason":"The maker's figure, from its print; the photo reads it within a pixel."},"note":"Faxon: \"a .615″ muzzle shoulder for the thread\". A ring 0.11 in long: what a muzzle device or its washer seats against."},"shoulder_x":{"label":"The muzzle shoulder ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":15.03,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/faxon-16-pencil-barrel f09ad3b5be48 (Primary Arms' gallery, 15A58M16NPQ_01: the barrel level on white, the muzzle at the right, the index pin and the gas port on top, 2000 x 1333)","scaleRef":"its end faces, 1821.3 px apart (columns 87.7 and 1909.0: where each end's rim arc reaches the full height, the silhouette at grey 235 of 255), as overall_length (16.631): 109.51 px/in. At that scale the gas block journal reads .6251 across (68.45 px over columns 1170 to 1284; published .625), 1.113 long (published 1.1) and the thread .6255 long (published .625): one scale for lengths and diameters","method":"the flange's rear face (column 194.6: where the flange's rim arc, seen past the extension's body over columns 188 to 194, reaches its full height) to the shoulder's face (column 1840.5, where the ring's full height ends; ahead of it the corner is the face's rim arc, to column 1845)","via":"harvest"}}],"note":"Where the thread begins: a muzzle device or its washer seats here. The published figures alone put it at 15.030 (overall_length less the extension behind the face less Faxon's .625 of thread)."},"thread_length":{"label":"The muzzle thread's length","kind":"length","measurements":[{"id":"faxon","value":0.625,"unit":"in","pm":0.0005,"stated":"Muzzle 1/2x28 UNF-2A, .625″ of thread, target crown","source":{"type":"spec","publisher":"manufacturer","name":"Faxon Firearms, FAXON DUTY SERIES PENCIL PROFILE 16\" MID-LENGTH 5.56 NATO AR15 BARREL (SKU 15A58M16NPQ), Specifications","url":"https://faxonfirearms.com/15A58M16NPQ","retrieved":"2026-10-12","via":"harvest"}},{"id":"photo","value":0.626,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/faxon-16-pencil-barrel f09ad3b5be48 (Primary Arms' gallery, 15A58M16NPQ_01: the barrel level on white, the muzzle at the right, the index pin and the gas port on top, 2000 x 1333)","scaleRef":"its end faces, 1821.3 px apart (columns 87.7 and 1909.0: where each end's rim arc reaches the full height, the silhouette at grey 235 of 255), as overall_length (16.631): 109.51 px/in. At that scale the gas block journal reads .6251 across (68.45 px over columns 1170 to 1284; published .625), 1.113 long (published 1.1) and the thread .6255 long (published .625): one scale for lengths and diameters","method":"the shoulder's face (column 1840.5) to the muzzle's face (column 1909.0, behind its rim's 6 px arc): 68.5 px","via":"harvest"}}],"adopt":{"from":"faxon","reason":"The maker's figure; the photo reads it within a thousandth."}},"thread_pitch":{"label":"The muzzle thread's pitch","kind":"length","measurements":[{"id":"faxon","value":0.03571,"unit":"in","pm":0.00005,"stated":"Muzzle 1/2x28 UNF-2A, .625″ of thread, target crown","source":{"type":"spec","publisher":"manufacturer","name":"Faxon Firearms, FAXON DUTY SERIES PENCIL PROFILE 16\" MID-LENGTH 5.56 NATO AR15 BARREL (SKU 15A58M16NPQ), Specifications","url":"https://faxonfirearms.com/15A58M16NPQ","retrieved":"2026-10-12","via":"harvest"}},{"id":"primary-arms","value":0.03571,"unit":"in","pm":0.00005,"stated":"Thread Pattern 1/2 X 28","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Faxon Firearms 5.56 AR-15 Barrel - Mid-Length - Pencil - 16\" (15A58M16NPQ), Specifications; its Features: \"Threaded 1/2x28\"","url":"https://www.primaryarms.com/faxon-firearms-5-56-ar-15-barrel-mid-length-pencil-16","retrieved":"2026-10-12","via":"harvest"}}],"adopt":{"from":"faxon","reason":"The maker's own; the seller states the same thread."},"note":"28 threads to the inch. Faxon's page for this barrel writes the class UNF-2A (its Gunner profile's page, UNEF-2A, which is the Army barrel's designation for the same 1/2-28)."},"thread_major_d":{"label":"The muzzle thread's major diameter (its crests)","kind":"length","measurements":[{"id":"tdp","value":0.4957,"unit":"in","pm":0.0033,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.thread_major_d}","via":"user"},"note":"The Army barrel's 1/2-28 thread, for the 1/2x28 Faxon states (8448549 sheet 1, Section M-M: \"1/2-28 UNEF-2A MAJOR DIA .4989/.4924\"), as read for BCM's barrel's ledger, where the drawing and its page are cited."}],"note":"The photo's thread reads 0.487 across its crests' silhouette (53.3 px), between its crests and its roots."},"thread_minor_d":{"label":"The muzzle thread's minor diameter (its roots)","kind":"length","measurements":[{"id":"tdp","value":0.4551,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.thread_minor_d}","via":"user"},"note":"8448549 sheet 1, Section M-M: \"MINOR DIA .4551 MAX\", as read for BCM's barrel's ledger. The photo has a relief of that diameter (49.3 px: .450) for 0.03 in ahead of the shoulder, where the thread runs out."}]},"bore_d":{"label":"The bore's diameter (across the lands)","kind":"length","measurements":[{"id":"tdp","value":0.219,"unit":"in","pm":0.001,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.bore_d}","via":"user"},"note":"The Army's barrel drawing (8448549 sheet 2, Section U-U: \".219 DIA+.001\"), as read for BCM's barrel's ledger, where the drawing and its page are cited."}],"note":"Faxon gives the grooves (\"groove .2250″ air-gauged\") and not the lands; the model's bore is one plain hole at the Army's land diameter."},"index_pin_d":{"label":"The barrel indexing pin's diameter","kind":"length","measurements":[{"id":"tdp","value":0.12525,"unit":"in","pm":0.00025,"source":{"type":"derived","expr":"{bca-556-16-mid-barrel.index_pin_d}","via":"user"},"note":"The Army's own part (8448551, Pin, Barrel Indexing: \".1255 DIA -.0005\"), as read for Bear Creek's barrel's ledger, where the drawing and its page are cited. Faxon: the extension is \"pinned\"."}],"note":"In the photo the pin shows 12.8 px of its width (0.117) before the flange's rim hides its front."},"index_pin_x":{"label":"The barrel indexing pin's axis behind the flange's rear face","kind":"length","measurements":[{"id":"photo","value":0.111,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/faxon-16-pencil-barrel f09ad3b5be48 (Primary Arms' gallery, 15A58M16NPQ_01: the barrel level on white, the muzzle at the right, the index pin and the gas port on top, 2000 x 1333)","scaleRef":"its end faces, 1821.3 px apart (columns 87.7 and 1909.0: where each end's rim arc reaches the full height, the silhouette at grey 235 of 255), as overall_length (16.631): 109.51 px/in. At that scale the gas block journal reads .6251 across (68.45 px over columns 1170 to 1284; published .625), 1.113 long (published 1.1) and the thread .6255 long (published .625): one scale for lengths and diameters","method":"the pin's rear edge on the upper silhouette (column 175.7) plus half index_pin_d (6.86 px), to the flange's rear face (column 194.6: where the flange's rim arc, seen past the extension's body over columns 188 to 194, reaches its full height)","via":"harvest"}}],"note":"BCM's reads 0.113. Its front stands 0.05 behind the flange's rear face."},"index_pin_top":{"label":"The barrel indexing pin's top above the bore's axis","kind":"length","measurements":[{"id":"photo","value":0.546,"unit":"in","pm":0.009,"source":{"type":"photo","photo":"references/faxon-16-pencil-barrel f09ad3b5be48 (Primary Arms' gallery, 15A58M16NPQ_01: the barrel level on white, the muzzle at the right, the index pin and the gas port on top, 2000 x 1333)","scaleRef":"its end faces, 1821.3 px apart (columns 87.7 and 1909.0: where each end's rim arc reaches the full height, the silhouette at grey 235 of 255), as overall_length (16.631): 109.51 px/in. At that scale the gas block journal reads .6251 across (68.45 px over columns 1170 to 1284; published .625), 1.113 long (published 1.1) and the thread .6255 long (published .625): one scale for lengths and diameters","method":"the pin's top on the upper silhouette, columns 177 to 187: row 605.2, 59.75 px above the axis (row 664.95, the middle of the extension's two edges)","via":"harvest"}}],"note":"A little under the flange's radius (0.582): the pin stands 0.046 out of the extension's .999, under the Army's .094 MAX (8448548)."},"extension_mouth_d":{"label":"The barrel extension's rear opening, its diameter at the rear face","kind":"length","measurements":[{"id":"model","value":0.77,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_mouth_d}","via":"user"}}],"note":"The inside of a mil-spec extension as the reference CAD set has it, read for BCM's barrel's ledger (where the file and the reading are cited), for how the rear end looks: Faxon's is an \"M4 feed-ramp barrel extension\", and Primary Arms' photo of its breech (21ee264e9f0f) shows its lugs and feed ramps. Appearance only."},"extension_mouth_chamfer":{"label":"The rear opening's chamfer, its depth (at 45°, also how far it narrows the opening's radius)","kind":"length","measurements":[{"id":"model","value":0.045,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_mouth_chamfer}","via":"user"}}]},"extension_lug_bore_d":{"label":"The circle the extension's locking lugs leave between their tips","kind":"length","measurements":[{"id":"model","value":0.572,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_lug_bore_d}","via":"user"}}]},"extension_lug_depth":{"label":"The locking lugs' front faces, ahead of the extension's rear end","kind":"length","measurements":[{"id":"model","value":0.214,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_lug_depth}","via":"user"}}]},"extension_recess_d":{"label":"The recess ahead of the lugs, which the bolt's lugs turn in: its diameter","kind":"length","measurements":[{"id":"model","value":0.83,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_recess_d}","via":"user"}}]},"extension_recess_depth":{"label":"The recess's front end, ahead of the extension's rear end","kind":"length","measurements":[{"id":"model","value":0.595,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_recess_depth}","via":"user"}}]},"outline_rear_face":{"label":"The extension's rear face in the traced outline's own frame (from the silhouette's rear tip)","kind":"length","measurements":[{"id":"photo","value":0.103,"unit":"in","pm":0.014,"source":{"type":"photo","photo":"references/faxon-16-pencil-barrel f09ad3b5be48 (Primary Arms' gallery, 15A58M16NPQ_01: the barrel level on white, the muzzle at the right, 2000 x 1333)","scaleRef":"scale from faxon-16-pencil-barrel.flange_od = 1.163 in (y-extent 127 px → 109.2 px/in)","method":"the min end's face: the silhouette's tip at 0.004 less its rim's arc, 0.099 in of sag at radius 0.489925 (the end is seen from 11.4° off square; arc fitted over 120 rows, rms 0.003) of the traced outline (tools/trace.py); the extension's rear face in the outline's own frame (from its rear tip)","via":"harvest"}}],"note":"Where the outline is cut: the silhouette's tip is the rear rim's near side, which stands behind the face by the rim's arc."},"outline_front_face":{"label":"The muzzle's face in the traced outline's own frame (from the silhouette's rear tip)","kind":"length","measurements":[{"id":"photo","value":16.804,"unit":"in","pm":0.131,"source":{"type":"photo","photo":"references/faxon-16-pencil-barrel f09ad3b5be48 (Primary Arms' gallery, 15A58M16NPQ_01: the barrel level on white, the muzzle at the right, 2000 x 1333)","scaleRef":"scale from faxon-16-pencil-barrel.flange_od = 1.163 in (y-extent 127 px → 109.2 px/in)","method":"the max end's face: the silhouette's tip at 16.841 less its rim's arc, 0.037 in of sag at radius 0.231795 (the end is seen from 9.0° off square; arc fitted over 120 rows, rms 0.003) of the traced outline (tools/trace.py); the muzzle's face in the outline's own frame (from its rear tip)","via":"harvest"}}],"note":"Where the outline is cut: the silhouette's front tip is the muzzle rim's near side."}}},{"subject":"fn-p90-50-magazine","title":"FN America PS90/P90 5.7x28mm Magazine, 50-round","dimensions":{"length":{"label":"Overall length, from the round rear end to the front cap's face","kind":"length","measurements":[{"id":"ar57-photo","value":10.92,"unit":"in","pm":0.1,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79 (Primary Arms' photo of the AR57 16 in upper's left side with this magazine on it, 2200 px; read from the magazine owner's side, 2026-10-18)","scaleRef":"std.picatinny.slot_pitch = 0.394 in: the receiver's top rail, its slots' leading edges at x 1678 to 2057 on the silhouette's top (12 pitches, 31.6 px each): 80.2 px/in; the handguard's M-LOK slots (std.mlok.slot_pitch, 40 mm) read 80.0 px/in on the same photo","method":"the magazine's silhouette against the white above it: its rear end at x 1636 (rows 640 and 660, where the luminance rises past 200), its cap's front face at x 760 ± 4 (row 630, behind the handguard's front rail's last tooth; the 4x crop's 763): 876 px. Both ends are at the centre plane's depth (a round end, a plane face), the rail's silhouette too; ± covers 4 px at each end and 0.5% of scale","via":"harvest"}},{"id":"ar57-12-photo","value":10.98,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/panzer-ar57-ult-12-upper c261b4c5a32d (Primary Arms' photo of the AR57 12 in upper's right side with this magazine on it, 2200 px; read from the magazine owner's side, 2026-10-18, detail pass)","scaleRef":"std.picatinny.slot_pitch = 0.394 in: the receiver's 13-slot rail, its teeth's leading edges on the silhouette's top at x 155 to 596 (12 pitches of 36.80 px, none off the line by more than 0.65 px): 93.39 px/in; the upper's lug holes as std.ar15.pin_spacing give 92.97 (0.45% less)","method":"its rear end at x 643.5 (rows 645 to 650, where the rail block's lit face meets the magazine's dark round end) and its cap's front face at x 1668.7 (rows 650 to 690, where the cap's lighter band meets the front block's darker face; at row 640 a white gap 3 px wide stands between the lug and the block's rearmost tooth, 1672 to 1674): 1025.2 px. By the pins it would be 11.03; ± covers 2 px at each end and the two scales","via":"harvest"}},{"id":"ar57-12-pins","value":11.03,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/panzer-ar57-ult-12-upper c261b4c5a32d (Primary Arms' photo of the AR57 12 in upper's right side with this magazine on it, 2200 px)","scaleRef":"the upper's lug holes as std.ar15.pin_spacing (takedown 254.0, 860.9; pivot 846.7, 864.6 px: 92.97 px/in), the frame the 12 in upper's model and its room are drawn in","method":"the same ends as ar57-12-photo, 643.5 and 1668.7 px: 1025.2 px; the rail's scale (93.39 px/in) reads 0.45% less. Detail pass, 2026-10-18 (the AR57 uppers' owner)","via":"harvest"}},{"id":"ar57-16-camera","value":10.87,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-16-upper 054c636f9e79 through the camera fitted to its own features of known size (the upper's ledger's header; .cache/ar57-camera/compare.py): the cap's front edge at 763 px (rows 640 to 685, where the cap's grey meets the block's) on the cap's near side, half fn-p90-50-magazine.cap_width out, where it stands against the block (the lens's foot is behind the block, so the cap's near side covers the riser's): 14.939; the rear end's outline at 1636 px as the round end it is (a half circle in plan as wide as the magazine, the line of sight tangent to it a little nearer the lens than its rearmost point): 4.065. Batch 12 read the face through a yaw correction fitted to the seller's back-to-muzzle length (15.187: 11.08), and this session first at the riser's side (15.040: 10.94).","via":"harvest"}},{"id":"ar57-12-camera","value":10.86,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d through the camera fitted to it (that upper's ledger's header): the cap's front edge at 1669.2 px (rows 650 to 690) on its near side: 14.962; the round rear end's outline at 644.5 px (row 670): 4.100. The other side of the same receiver, from another lens 23 in off: within 0.012 of the 16 in's (ar57-16-camera). Batch 12's ar57-12-pins (11.03) is the same pixels in a pin frame of the holes' see-through middles, which reads that photo 1.5% small.","via":"harvest"}},{"id":"ar57-16-above-latch","value":10.869,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-16-upper 054c636f9e79 through the camera fitted to it (that upper's ledger's header; 2026-10-19 (night), .cache/ar57-camera/pass3/magend.py): the cap's front edge 14.939, as ar57-16-camera; the round rear end where it stands against the white above the latch that holds it, 1635.3 to 1635.4 px along rows 646 to 654, as the round end it is (fn-p90-50-magazine.width), the line of sight tangent to it near its rearmost point: 4.070 (4.070 to 4.071 over the five rows). ar57-16-camera's 1636 px at row 668 is at the latch's height, where the latch's dark lobe stands between the magazine and the rail block.","via":"harvest"}},{"id":"ar57-12-above-latch","value":10.88,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d through the camera fitted to it (that upper's ledger's header; 2026-10-19 (night)): the cap's front edge 14.962, as ar57-12-camera; the round rear end where it stands against the rail block's lit face above the latch, 643.6 to 643.8 px along rows 650 to 662: 4.082 (4.077 to 4.087, a little more lower down). ar57-12-camera's 644.5 px at row 670 is at the latch's height, beside the latch's lit rim.","via":"harvest"}}],"adopt":{"from":"ar57-16-above-latch","reason":"The magazine's own two ends through two cameras: its cap's front edge where it stands against the front block, and its round rear end above the latch that holds it. Since 2026-10-19 (night) the rear end isn't taken to bear on the rail block's face: both uppers' photos through their cameras have that face 0.10 in behind it, white between the two above and below the latch (the uppers' ledgers: rail_block_front_x, latch_top_y). The 16 in's, read against the white over five rows within 0.001 from a lens 43 in off; the 12 in's, from 23 in, 0.011 more. The readings of the rear end at the latch's height (ar57-16-camera, ar57-12-camera) and every pin frame's are kept. Each upper's front block face is drawn bearing on the cap (their ledgers: front_block_face_x)."},"note":"No page gives it. The P90 render on Wikipedia (123b6947565b) shows 9.7 in of it ahead of the rifle's rear cover, which hides the rest: no check beyond that it is longer. Readings scaled by it on Blackstone's photos (width, tower, its drop, height, cap) were written again at 11.03 (2026-10-18, batch 12; 1% less at 10.92) at 10.86 that night (the two AR57 rooms through their photos' cameras), and at 10.869 on 2026-10-19 (the rear end read above the latch)."},"width":{"label":"Body width, across (the rounds lie this way, facing left)","kind":"length","measurements":[{"id":"top-photo","value":1.949,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/fn-p90-50-magazine 0db3af782b2b (Blackstone's photo of its top face, the cap up and the tower's end down, 1280 px)","scaleRef":"fn-p90-50-magazine.length = 10.869 in over the silhouette's 1233 px (rows 24 to 1257, the cap's face to the round end): 113.44 px/in (111.8 at 11.03, 112.9 at 10.92 and 113.5 at 10.86 before)","method":"the silhouette's width (luminance < 240) on rows 100 to 1020: 218 to 224 px, growing toward the tower end (nearer the lens), 221 at mid-length; ± covers that spread and a view a few degrees off square (its side face then adds to the width)","via":"harvest"}},{"id":"tower-centre","value":1.924,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/fn-p90-50-magazine 76c0d7572a37 (Blackstone's side view of the magazine alone, 500 px, the tower down at the left)","scaleRef":"fn-p90-50-magazine.length = 10.869 in over the silhouette's 435 px (x 32 to 467): 40.02 px/in (39.44 at 11.03, 39.8 at 10.92 and 40.06 at 10.86 before)","method":"twice the distance from the rear end (x 32) to the middle of the tower's bottom silhouette (x 33.5 to 108.5): 38.5 px; the tower is concentric with the round end in US 4,905,394's FIG. 3 and FIG. 4 and in every photo from below","via":"harvest"}}],"adopt":{"from":"top-photo","reason":"A width read across the face itself; the other is a length along the side doubled, on the assumption that the tower is concentric with the round end. They agree within 0.03 in; the patent's plan (FIG. 3, 5.55 lengths to the width) gives 1.96 at this length."}},"height":{"label":"Body height (its thickness, top face to underside)","kind":"length","measurements":[{"id":"ar57-photo","value":0.77,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79 (Primary Arms' photo of the AR57 16 in upper's left side with this magazine on it, 2200 px)","scaleRef":"std.picatinny.slot_pitch: 80.2 px/in, as fn-p90-50-magazine.length","method":"on columns 830, 1000 and 1200: its top silhouette at row 636.5 (the white above turns dark), its underside at row 698.5 (at x 830 a white gap under it begins there): 62 px. A camera a degree off level would add the top or the bottom face's 1.96 in times its sine (0.03 in a degree): the ± covers about one","via":"harvest"}},{"id":"side-photo","value":0.73,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/fn-p90-50-magazine 76c0d7572a37 (Blackstone's side view of the magazine alone, 500 px, taken from above: its top face shows as a band)","scaleRef":"fn-p90-50-magazine.length = 10.869 in over 435 px: 40.02 px/in (39.44 at 11.03, 39.8 at 10.92 and 40.06 at 10.86 before)","method":"on columns 150, 250, 350 and 420: the top face's band 25.5 px (rows 216 to 241.5) and the side face's 27.5 px (241.5 to 269); the top face's band over fn-p90-50-magazine.width says the view is 19.1 degrees from above, and the side's band over its cosine is the height","via":"harvest"}},{"id":"p90-render","value":0.87,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/fn-p90-50-magazine 123b6947565b (Wikipedia's render of the P90 with no background, 960 px, the magazine seated)","scaleRef":"the rifle's overall length, 19.88 in (FNH USA's 2009 catalog, every P90: references/fn-p90-50-magazine/docs/b3fed823b9.pdf) over the alpha silhouette's 830 px (x 60 to 889): 41.75 px/in","method":"the magazine's side between the frame's top (row 168) and the light line under it (row 204.5), on columns 260 to 590: 36.5 px","via":"harvest"},"note":"Not adopted: a render whose scale is the rifle's length to whatever the render's muzzle device is, and 0.1 in over both photos of the magazine itself."}],"adopt":{"from":"ar57-photo","reason":"A photo of this magazine scaled by two standards in the same photo (the rail's and the M-LOK slots' pitches agree within 0.3%), read square from the side. Blackstone's photo of it alone, read through the angle it is taken from, agrees within the two readings' ±; Wikipedia's P90 render reads 0.1 in more and is kept beside them. Two rows of 5.7x28 cases stacked staggered (the patent's FIG. 7) need 0.58 in inside: either photo's figure leaves walls of about 0.08."}},"tower_d":{"label":"Feed tower's diameter (the black cap on the underside at the rear end, that the rounds turn through)","kind":"length","measurements":[{"id":"side-photo","value":1.873,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/fn-p90-50-magazine 76c0d7572a37 (Blackstone's side view of the magazine alone, 500 px)","scaleRef":"fn-p90-50-magazine.length = 10.869 in over 435 px: 40.02 px/in (39.44 at 11.03, 39.8 at 10.92 and 40.06 at 10.86 before)","method":"the tower's bottom silhouette below the body's underside from x 33.5 to 108.5 (75 px): seen from 19 degrees above, a level circle's ends along the axis are its diameter","via":"harvest"}}],"note":"The side view of the magazine alone, where its length along the magazine is read square, has it 1.90, its rear at the body's rear end within a pixel (column 34 against the body's 33 at row 267), as US 4,905,394's FIG. 7 draws the feed housing flush with the magazine's rear end and FIG. 3 its circle on the round end's. The views that look at its face have it wider than the body beside it (Blackstone's top view 0db3af782b2b: it shows past the body's right side by 30 px over 110 px of its length; from below, 128e601bf5c7, 785f74cccd90, ed67cb0af658, a fifth wider at a glance): each is a close view whose lens stands nearer the tower's face than the body's edges it is compared with (0.48 to 1.25 in nearer, a tenth of a close lens's distance), or a few degrees off square (0db3af782b2b, whose tower is 1.25 in under the face it was read beside); none is a reading of its size. On the AR57 it shows through a notch in the receiver's near wall 1.52 long (the upper's feed_notch_length): the chord its round pocket cuts in that wall, not the tower; the upper's pocket is this figure and a clearance (its feed_pocket_d). Both kept: this one the tower's, that one the wall's."},"tower_drop":{"label":"Feed tower: how far its bottom face stands below the body's underside","kind":"length","measurements":[{"id":"side-photo","value":0.473,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/fn-p90-50-magazine 76c0d7572a37 (Blackstone's side view of the magazine alone, 500 px, 19.1 degrees from above)","scaleRef":"fn-p90-50-magazine.length = 10.869 in over 435 px: 40.02 px/in (39.44 at 11.03, 39.8 at 10.92 and 40.06 at 10.86 before)","method":"its lowest silhouette at row 286 (x 68 to 78), the body's at 268.5 there: 17.5 px, 0.44 in on the image; seen from above, each silhouette is its near lower edge, the tower's 0.04 in nearer the middle than the body's, so 0.44 = drop × cos 19.1° − 0.01: 0.48","via":"harvest"}},{"id":"ar57-photo","value":0.52,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79 (Primary Arms' photo of the AR57 16 in upper's left side, 2200 px)","scaleRef":"std.picatinny.slot_pitch: 80.2 px/in","method":"a round piece under the magazine's rear end, x 1499 to 1616, from its underside (row 698.5) to the receiver's top (row 740): 41.5 px","via":"harvest"},"note":"Not adopted: what shows there is the tower through a notch in the receiver's near wall 1.46 in across (the upper's owner reads it 1.52, feed_pocket_d), its bottom at the notch's floor or under the receiver's top: the depth to the receiver is the upper's to read."},{"id":"seated-close","value":0.55,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 8b39baf7f412 (a close view of an AR57's right side with this magazine seated and loaded, 700 px)","scaleRef":"fn-p90-50-magazine.height = 0.77 in over the body's 95 px there (its top at row 43, its underside at row 138)","method":"the tower from the body's underside to its own bottom face in the receiver's stepped pocket, rows 138 to 207: 0.72 of the body's height; ± for a close photo (the receiver's notch is nearer the lens than the body's middle)","via":"harvest"},"note":"A third reading, of the tower in its pocket: within the two others' ± of the side view's 0.48."}],"adopt":{"from":"side-photo","reason":"The magazine alone, where nothing else can be taken for its tower; on the AR57 it shows only through the receiver's notch."}},"cap_length":{"label":"Front cap: its length along the magazine (its face to its rear edge on the side)","kind":"length","measurements":[{"id":"ar57-photo","value":0.45,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79 (Primary Arms' photo of the AR57 16 in upper's left side, 2200 px)","scaleRef":"std.picatinny.slot_pitch: 80.2 px/in","method":"on the 4x crop of x 640 to 900: the cap's face at x 760, its rear edge on the side (a vertical line where the smoke body's window begins) at x 796: 36 px","via":"harvest"}}]},"cap_above":{"label":"Front cap: how far its top (its latch lugs) stands above the body's top","kind":"length","measurements":[{"id":"ar57-photo","value":0.17,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79 (Primary Arms' photo of the AR57 16 in upper's left side, 2200 px)","scaleRef":"std.picatinny.slot_pitch: 80.2 px/in","method":"the silhouette's top at row 623 from x 785 to 808 (the lugs) and 625 ahead of them, the body's top at 636.5: 13.5 px","via":"harvest"}}]},"cap_below":{"label":"Front cap: how far it reaches below the body's underside","kind":"length","measurements":[{"id":"ar57-photo","value":0.22,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79 (Primary Arms' photo of the AR57 16 in upper's left side, 2200 px)","scaleRef":"std.picatinny.slot_pitch: 80.2 px/in","method":"on the 4x crop: the cap's lower end at row 716, against the white gap under the body (rows 699 to 716 at x 830); the body's underside at 698.5: 17.5 px","via":"harvest"}}]},"cap_lug_length":{"label":"Front cap: its latch lugs' reach back from the cap's face, on its top","kind":"length","measurements":[{"id":"ar57-photo","value":0.6,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79 (Primary Arms' photo of the AR57 16 in upper's left side, 2200 px)","scaleRef":"std.picatinny.slot_pitch: 80.2 px/in","method":"the silhouette's top stays above the body's from the cap's face (x 760) to x 808: 48 px","via":"harvest"}}]},"cap_width":{"label":"Front cap: its width across","kind":"length","measurements":[{"id":"top-photo","value":2.04,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/fn-p90-50-magazine 0db3af782b2b (Blackstone's photo of its top face, 1280 px)","scaleRef":"fn-p90-50-magazine.length = 10.869 in over 1233 px: 113.44 px/in (111.8 at 11.03, 112.9 at 10.92 and 113.5 at 10.86 before)","method":"the silhouette's width on row 60 (the cap): 231 px, 10 px more than the body's below it","via":"harvest"}}]},"cap_lug_width":{"label":"Front cap: each of its two latch lugs' width across (one at each side, a gap between)","kind":"length","measurements":[{"id":"assumed","value":0.5,"unit":"in","pm":0.15,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: Blackstone's photo of the top face (0db3af782b2b) shows the two lugs at the cap's two sides with a gap between, about a quarter of the cap's width each; no view squares them.","via":"harvest"}}]},"cap_foot_slope":{"label":"Front cap: the slope of its feet's backs (where the cap's band, under the underside, rises back toward the rib behind it), from the underside's plane","kind":"angle","measurements":[{"id":"ar57-photo","value":48,"unit":"deg","pm":10,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79 (Primary Arms' photo of the AR57 16 in upper's left side, 2200 px; detail pass, 2026-10-18)","scaleRef":"the photo's own pixels both ways (an angle)","method":"the silhouette's lower edge against the light under the magazine's front end, column by column: at row 714.5 to 715.5 from the cap's face back to x 797, then 713.5, 711.5, 710.5, 709.5 and 704.5 at x 798 to 806, where the rib's foot begins: 10 px up over 9 px back; ± for a pixel at each end","via":"harvest"}}]},"rib_from_face":{"label":"The rib across the underside behind the front cap: its front edge's distance behind the cap's face","kind":"length","measurements":[{"id":"ar57-photo","value":0.55,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79 (Primary Arms' photo of the AR57 16 in upper's left side, 2200 px; detail pass, 2026-10-18)","scaleRef":"std.picatinny.slot_pitch: 80.2 px/in, as fn-p90-50-magazine.length","method":"the silhouette's lower edge under the front end (light under it to the handguard's top at row 717.5): the cap's foot ramps up to the rib's level at x 806, the cap's face at x 762 (rows 650 to 690): 44 px","via":"harvest"}}],"note":"A rounded bar across the underside right behind the cap, its ends rounded: Midwest Gun Works' view of the underside (128e601bf5c7) and Wikimedia's FNP90MAG02 (785f74cccd90, its full-size copy 79ffb375bc2f) show it across the face; the AR57 photo shows it from the side as a bump under the front end, clear of the handguard's top."},"rib_length":{"label":"The rib across the underside: its width along the magazine","kind":"length","measurements":[{"id":"ar57-photo","value":0.25,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79 (Primary Arms' photo of the AR57 16 in upper's left side, 2200 px; detail pass, 2026-10-18)","scaleRef":"std.picatinny.slot_pitch: 80.2 px/in","method":"its foot under the body from x 806 to x 826, where the silhouette's lower edge is back at the underside (row 698.5 from x 828): 20 px","via":"harvest"}}]},"rib_drop":{"label":"The rib across the underside: how far it stands below the underside","kind":"length","measurements":[{"id":"ar57-photo","value":0.08,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79 (Primary Arms' photo of the AR57 16 in upper's left side, 2200 px; detail pass, 2026-10-18)","scaleRef":"std.picatinny.slot_pitch: 80.2 px/in","method":"the silhouette's lower edge at rows 704.5 to 705.5 from x 806 to 818, the underside's at 698.5 (x 828 to 844, the light under it from row 699 to the handguard at 717.5): 6.5 px","via":"harvest"}}]},"rib_span":{"label":"The rib across the underside: its length across the magazine, end to rounded end","kind":"length","measurements":[{"id":"assumed","value":1.5,"unit":"in","pm":0.15,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: on the two views of the underside that show the rib whole, both oblique (79ffb375bc2f from below and ahead, 128e601bf5c7 from above at an angle), it runs about three quarters of the face's width at a glance (0.76 and 0.8), its ends well inside the long edges; no view squares it.","via":"harvest"}}]},"cap_panel_frame":{"label":"Front cap: the frame round the recessed panel in each of its sides (at the panel's front and over it)","kind":"length","measurements":[{"id":"ar57-photo","value":0.07,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79 (Primary Arms' photo of the AR57 16 in upper's left side, 2200 px; detail pass, 2026-10-18)","scaleRef":"std.picatinny.slot_pitch: 80.2 px/in","method":"on a 10x crop of x 735 to 805: the cap's side is a frame round a flat panel, lit along the frame's inner edge; the frame from the cap's face (764) to the panel (771) is 7 px, and over the panel (rows 636.5 to 641) 4.5 px: 0.09 and 0.056; under it the panel runs down to the underside","via":"harvest"}}]},"cap_panel_depth":{"label":"Front cap: how deep the panel in each of its sides is recessed","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the AR57 photo (054c636f9e79) shows the panel square on, its frame's inner edge lit, and no view has it in profile; the cap stands only 0.045 in proud of the body's side (cap_width less width, halved), so the recess is drawn less than that.","via":"harvest"}}]},"ring_od":{"label":"The raised ring on the underside just ahead of the feed tower: its outside diameter","kind":"length","measurements":[{"id":"assumed","value":0.45,"unit":"in","pm":0.07,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: in the two close views from below that show it beside the tower's face (ed67cb0af658, 128e601bf5c7) it is about a quarter of the tower's diameter across at a glance (0.235 and 0.27 of it), nearly touching the tower's edge, between the two index lines down the face and near the middle of them (also 79ffb375bc2f); no view squares it.","via":"harvest"}}]},"ring_id":{"label":"The raised ring on the underside: its bore's diameter","kind":"length","measurements":[{"id":"assumed","value":0.3,"unit":"in","pm":0.06,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the bore is about two thirds of the ring across in ed67cb0af658 and 79ffb375bc2f (0.68 and 0.74), a floor lit inside it.","via":"harvest"}}]},"ring_height":{"label":"The raised ring on the underside: how far it stands proud of the face","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the close views show its outer wall as a narrow band below its flat top (ed67cb0af658, 9516509da8f4); no view has it in profile.","via":"harvest"}}]},"ring_bore_depth":{"label":"The raised ring on the underside: how deep its bore goes below its top","kind":"length","measurements":[{"id":"assumed","value":0.1,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: its floor shows lit inside the bore in ed67cb0af658, a little below the face at a glance; the model is a solid body, so the bore stops there.","via":"harvest"}}]},"edge_radius":{"label":"The body's long edges, their round","kind":"length","measurements":[{"id":"assumed","value":0.15,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: US 4,905,394's section through the feed end (sheet 2, FIG. 8) rounds its four outer corners by about an eighth of its width at a glance, and the photos from the side and the ends show the same soft edges; no view of the product has a corner in profile.","via":"harvest"}}]},"lip_bar_width":{"label":"Feed tower's bottom face: the bar the round lies in (its two lips), its width across","kind":"length","measurements":[{"id":"assumed","value":0.72,"unit":"in","pm":0.12,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: on the photos from below (785f74cccd90, ed67cb0af658, 128e601bf5c7) the two lips with the slot between them are about two and a half of the case's widths across at a glance; no view squares the bar.","via":"harvest"}}]},"slot_width":{"label":"Feed tower's bottom face: the slot along the bar that the top round lies in, its width","kind":"length","measurements":[{"id":"derived","value":0.313,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{.cartridge_base_d}"},"note":"As wide as the case that lies in it (785f74cccd90, ed67cb0af658): the slot is that case's width on every photo of it loaded."}]},"pocket_depth":{"label":"Feed tower's bottom face: the two D-shaped pockets either side of the bar, their depth","kind":"length","measurements":[{"id":"assumed","value":0.12,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the photos from below (785f74cccd90, ed67cb0af658, 128e601bf5c7) show the two pockets' walls lit and their floors dark, about a sixth of the tower's drop; no view has them in profile.","via":"harvest"}}]},"pocket_rim":{"label":"Feed tower's bottom face: the rim round its two pockets, its width","kind":"length","measurements":[{"id":"assumed","value":0.12,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the photos from below (785f74cccd90, ed67cb0af658, 128e601bf5c7) show a rim round the face about a sixteenth of its diameter wide at a glance; no view squares it.","via":"harvest"}}]},"cartridge_base_d":{"label":"A 5.7x28 case's base diameter (what lies in the feed slot)","kind":"length","measurements":[{"id":"wikipedia","value":7.95,"unit":"mm","pm":0.005,"stated":"Base diameter 7.95 mm (0.313 in)","source":{"type":"spec","publisher":"review","name":"Wikipedia, FN 5.7×28mm (its specifications, citing the C.I.P. data sheet)","url":"https://en.wikipedia.org/wiki/FN_5.7%C3%9728mm","retrieved":"2026-10-18","via":"harvest"}}]},"cartridge_length":{"label":"A 5.7x28 round's overall length (the rounds lie across the body)","kind":"length","measurements":[{"id":"wikipedia","value":40.5,"unit":"mm","pm":0.005,"stated":"Overall length 40.50 mm (1.594 in)","source":{"type":"spec","publisher":"review","name":"Wikipedia, FN 5.7×28mm (its specifications, citing the C.I.P. data sheet)","url":"https://en.wikipedia.org/wiki/FN_5.7%C3%9728mm","retrieved":"2026-10-18","via":"harvest"}}],"note":"A check on the width: 1.594 in of round lie across 1.98 in of body (Wikipedia's P90: \"it contains 50 rounds of ammunition which lie in two rows facing left, offset 90° from the bore axis\"), leaving 0.18 in for each wall and the room the rounds move in."},"capacity":{"label":"Capacity","kind":"count","measurements":[{"id":"fn","value":50,"unit":"count","stated":"e. 5.7x28mm Magazine Product No: 3810110093 (50-round)","source":{"type":"spec","publisher":"manufacturer","name":"FNH USA, 2009 catalog, PS90/P90 accessories (archived copy)","url":"https://web.archive.org/web/20110711014348/http://fnhusa1.com/PDF/2009FNHUSAcatalog.pdf","retrieved":"2026-10-18","via":"harvest"}}]},"round_weight":{"label":"One 5.7x28 round's weight","kind":"mass","measurements":[{"id":"wikipedia","value":6,"unit":"g","pm":0.05,"stated":"The 5.7×28mm cartridge weighs 6.0 grams (93 grains)","source":{"type":"spec","publisher":"review","name":"Wikipedia, FN 5.7×28mm","url":"https://en.wikipedia.org/wiki/FN_5.7%C3%9728mm","retrieved":"2026-10-18","via":"harvest"}}],"note":"Of no load in particular (FN's SS190 as Wikipedia gives it); the loads sold differ by a few grains of bullet."},"p90_weight_empty":{"label":"A P90's weight empty (for the magazine's weight by difference)","kind":"mass","measurements":[{"id":"wikipedia","value":5.5,"unit":"lb","pm":0.05,"stated":"weighing 2.5 kg (5.5 lb) empty, or 3 kg (6.6 lb) with a loaded 50-round magazine","source":{"type":"spec","publisher":"review","name":"Wikipedia, FN P90","url":"https://en.wikipedia.org/wiki/FN_P90","retrieved":"2026-10-18","via":"harvest"}}]},"p90_weight_loaded":{"label":"A P90's weight with a loaded 50-round magazine","kind":"mass","measurements":[{"id":"wikipedia","value":6.6,"unit":"lb","pm":0.05,"stated":"weighing 2.5 kg (5.5 lb) empty, or 3 kg (6.6 lb) with a loaded 50-round magazine","source":{"type":"spec","publisher":"review","name":"Wikipedia, FN P90","url":"https://en.wikipedia.org/wiki/FN_P90","retrieved":"2026-10-18","via":"harvest"}}]},"weight":{"label":"Weight, empty","kind":"mass","measurements":[{"id":"p90-difference","value":7,"unit":"oz","pm":1.7,"source":{"type":"derived","expr":"{.p90_weight_loaded} - {.p90_weight_empty} - {.capacity} * {.round_weight}"}},{"id":"kygunco","value":2,"unit":"lb","stated":"Weight 2 lb","source":{"type":"spec","publisher":"retailer","name":"KYGUNCO, FN AMERICA PS90 5.7x28 50rd Smoke Finish Magazine","url":"https://www.kygunco.com/product/fnh-usa-3810110093-ps90-5.7x28-50rd-smoke-finish-magazine","retrieved":"2026-10-18","via":"harvest"},"note":"The seller's shipping weight, the same \"2 lb\" its markup gives every small item: a whole loaded P90 is 6.6 lb."}],"adopt":{"from":"p90-difference","reason":"The seller's 2 lb is its shipping class, not the magazine (a loaded P90 is 6.6 lb and an empty one 5.5); the difference of the rifle's two weights is the only figure for the magazine itself."},"note":"No page states it. Worked out from Wikipedia's two weights of the P90 (with a loaded 50-round magazine, and empty, which is taken as without one) less fifty rounds; the pounds are the page's rounded conversions (± 0.05 lb each), so the figure is good to about ± 1.7 oz."}}},{"subject":"geissele-139-chf-barrel","title":"Geissele Automatics CHF Chrome Lined Barrel - 5.56 - 13.9\" (05-2989)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"primary-arms","value":1.5,"unit":"lb","pm":0.05,"stated":"1.5 lbs weight","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics CHF Chrome Lined 5.56 AR-15 Barrel - Mid-Length - Tapered - 13.9\" (05-2989), Features; its Specifications: \"Weight 1.5 lbs\"","url":"https://www.primaryarms.com/geissele-automatics-5-56-chf-mid-length-taper-profile-ar-15-barrel-chrome-lined-13-9in","retrieved":"2026-10-06","via":"harvest"}},{"id":"huckleberry","value":1.5,"unit":"lb","pm":0.05,"stated":"Weight 1.5 lbs","source":{"type":"spec","publisher":"retailer","name":"Huckleberry Arms, Geissele CHF Chrome Lined Barrel 5.56 NATO – 13.9\" (Product Code 05-2989), Technical Specs","url":"https://www.huckleberryarms.com/geissele-chf-chrome-lined-barrel-556-13-9-inch-p/05-2989.htm","retrieved":"2026-10-06","via":"harvest"}},{"id":"rooftop","value":1.5,"unit":"lb","pm":0.005,"stated":"Weight: 1.50 Pounds","source":{"type":"spec","publisher":"retailer","name":"Rooftop Defense, Geissele Automatics 13.9\" 5.56 Hammer-Forged Midlength Barrel (Geissele Part Number 05-2989), Specifications","url":"https://www.rooftopdefense.com/product/geissele-automatics-13-9-5-56-hammer-forged-midlength-barrel/","retrieved":"2026-10-06","via":"harvest"}},{"id":"ar15discounts","value":24,"unit":"oz","pm":0.5,"stated":"Weight 24 oz","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, Geissele 5.56 NATO 13.9\" 1:7 Midlength Cold Hammer Forged Chrome Lined Barrel - 05-2989 (its own SKU 16938; MPN 05-2989, UPC 810081134958), Additional information; its Specifications: \"Weight: 1.5Lbs\"","url":"https://ar15discounts.com/products/geissele-5-56-nato-13-9-17-midlength-cold-hammer-forged-chrome-lined-barrel/","retrieved":"2026-10-06","via":"harvest"}},{"id":"dirty-bird","value":24,"unit":"oz","pm":0.5,"stated":"Weight 24 oz","source":{"type":"spec","publisher":"retailer","name":"Dirty Bird Industries, Geissele 5.56 NATO 13.9\" 1:7 Midlength Cold Hammer Forged Chrome Lined Barrel - 05-2989 (MPN 05-2989), Additional information; its Specifications: \"Weight: 1.5Lbs\"","url":"https://dirtybirdusa.com/products/geissele-5-56-nato-13-9-17-midlength-cold-hammer-forged-chrome-lined-barrel/","retrieved":"2026-10-06","via":"harvest"}},{"id":"kenzies","value":1.5,"unit":"lb","pm":0.05,"stated":"Weight 1.5lbs","source":{"type":"spec","publisher":"retailer","name":"Kenzie's Optics, Geissele CHF Chrome Lined Barrel - 5.56 - 13.9\" (SKU 05-2989), Specifications","url":"https://www.kenziesoptics.com/product/geissele-chf-chrome-lined-barrel-5-3/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"primary-arms","reason":"Six sellers' pages state the one figure; Primary Arms' is the page whose photos the barrel is drawn from. Geissele's own page isn't read."},"note":"Six sellers, one figure (24 oz is 1.5 lb), none the maker's own page. The model's volume as steel is the check (app/tests/geissele-139-chf-barrel.test.ts)."},"length":{"label":"Barrel length as its sellers state it for the maker","kind":"length","measurements":[{"id":"primary-arms","value":13.9,"unit":"in","pm":0.05,"stated":"Barrel Length 13.9","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics CHF Chrome Lined 5.56 AR-15 Barrel - Mid-Length - Tapered - 13.9\" (05-2989), Specifications; its Features: \"13.9\" cold hammer-forged barrel\"","url":"https://www.primaryarms.com/geissele-automatics-5-56-chf-mid-length-taper-profile-ar-15-barrel-chrome-lined-13-9in","retrieved":"2026-10-06","via":"harvest"}},{"id":"huckleberry","value":13.9,"unit":"in","pm":0.05,"stated":"Barrel Length 13.9 inches","source":{"type":"spec","publisher":"retailer","name":"Huckleberry Arms, Geissele CHF Chrome Lined Barrel 5.56 NATO – 13.9\" (Product Code 05-2989), Technical Specs","url":"https://www.huckleberryarms.com/geissele-chf-chrome-lined-barrel-556-13-9-inch-p/05-2989.htm","retrieved":"2026-10-06","via":"harvest"}},{"id":"rooftop","value":13.9,"unit":"in","pm":0.05,"stated":"Length: 13.9″","source":{"type":"spec","publisher":"retailer","name":"Rooftop Defense, Geissele Automatics 13.9\" 5.56 Hammer-Forged Midlength Barrel (Geissele Part Number 05-2989), Specifications","url":"https://www.rooftopdefense.com/product/geissele-automatics-13-9-5-56-hammer-forged-midlength-barrel/","retrieved":"2026-10-06","via":"harvest"}},{"id":"kenzies","value":13.9,"unit":"in","pm":0.05,"stated":"Length 13.9″","source":{"type":"spec","publisher":"retailer","name":"Kenzie's Optics, Geissele CHF Chrome Lined Barrel - 5.56 - 13.9\" (SKU 05-2989), Specifications","url":"https://www.kenziesoptics.com/product/geissele-chf-chrome-lined-barrel-5-3/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"primary-arms","reason":"Four sellers' pages state the one length; none is the maker's own page, which isn't read."},"note":"The nominal length: what the site's federal-law line goes by (D80). No page says between which points; the Army's barrel drawing (8448549) dimensions a barrel from its breech end, inside the extension, to its muzzle, and overall_length takes it so. Under 16 in: the length Geissele's own complete uppers carry with a muzzle device pinned and welded on (the sellers' sentences are in the owner's report, not here)."},"journal_od":{"label":"The gas block journal's diameter","kind":"length","measurements":[{"id":"primary-arms","value":0.75,"unit":"in","pm":0.0005,"stated":"Gas Seat Diameter .750","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics CHF Chrome Lined 5.56 AR-15 Barrel - Mid-Length - Tapered - 13.9\" (05-2989), Specifications; its Features: \".750\" gas block diameter, .081\" gas port\"","url":"https://www.primaryarms.com/geissele-automatics-5-56-chf-mid-length-taper-profile-ar-15-barrel-chrome-lined-13-9in","retrieved":"2026-10-06","via":"harvest"}},{"id":"huckleberry","value":0.75,"unit":"in","pm":0.0005,"stated":"Gas Block Diameter .750\"","source":{"type":"spec","publisher":"retailer","name":"Huckleberry Arms, Geissele CHF Chrome Lined Barrel 5.56 NATO – 13.9\" (Product Code 05-2989), Technical Specs","url":"https://www.huckleberryarms.com/geissele-chf-chrome-lined-barrel-556-13-9-inch-p/05-2989.htm","retrieved":"2026-10-06","via":"harvest"}},{"id":"rooftop","value":0.75,"unit":"in","pm":0.0005,"stated":"Gas Block Journal Diameter: 0.750″","source":{"type":"spec","publisher":"retailer","name":"Rooftop Defense, Geissele Automatics 13.9\" 5.56 Hammer-Forged Midlength Barrel (Geissele Part Number 05-2989), Specifications","url":"https://www.rooftopdefense.com/product/geissele-automatics-13-9-5-56-hammer-forged-midlength-barrel/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"primary-arms","reason":"Three sellers' pages state the one diameter; none is the maker's own page."}},"gas_port_d":{"label":"The gas port's diameter","kind":"length","measurements":[{"id":"primary-arms","value":0.081,"unit":"in","pm":0.0005,"stated":".750\" gas block diameter, .081\" gas port","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics CHF Chrome Lined 5.56 AR-15 Barrel - Mid-Length - Tapered - 13.9\" (05-2989), Features","url":"https://www.primaryarms.com/geissele-automatics-5-56-chf-mid-length-taper-profile-ar-15-barrel-chrome-lined-13-9in","retrieved":"2026-10-06","via":"harvest"}},{"id":"huckleberry","value":0.081,"unit":"in","pm":0.0005,"stated":"Gas Port .081","source":{"type":"spec","publisher":"retailer","name":"Huckleberry Arms, Geissele CHF Chrome Lined Barrel 5.56 NATO – 13.9\" (Product Code 05-2989), Technical Specs","url":"https://www.huckleberryarms.com/geissele-chf-chrome-lined-barrel-556-13-9-inch-p/05-2989.htm","retrieved":"2026-10-06","via":"harvest"}},{"id":"rooftop","value":0.081,"unit":"in","pm":0.0005,"stated":"Gas Port: 0.081″","source":{"type":"spec","publisher":"retailer","name":"Rooftop Defense, Geissele Automatics 13.9\" 5.56 Hammer-Forged Midlength Barrel (Geissele Part Number 05-2989), Specifications","url":"https://www.rooftopdefense.com/product/geissele-automatics-13-9-5-56-hammer-forged-midlength-barrel/","retrieved":"2026-10-06","via":"harvest"}},{"id":"kenzies","value":0.081,"unit":"in","pm":0.0005,"stated":"Gas Port .081","source":{"type":"spec","publisher":"retailer","name":"Kenzie's Optics, Geissele CHF Chrome Lined Barrel - 5.56 - 13.9\" (SKU 05-2989), Specifications","url":"https://www.kenziesoptics.com/product/geissele-chf-chrome-lined-barrel-5-3/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"primary-arms","reason":"Four sellers' pages state the one figure (and AR15Discounts', Dirty Bird's and C. Stephens' the same)."},"note":"Published for this number (the 14.5 in sibling's is .076 on the same sellers' pages). In Primary Arms' side photo the port faces the lens: 11 px across, 0.080 in at the journal's scale."},"extension_behind_breech":{"label":"The barrel extension's rear end behind the barrel's breech end","kind":"length","measurements":[{"id":"model","value":0.501,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{std.ar15.barrel_extension_behind_breech}","via":"user"}}],"note":"The standard's (the reference CAD set's extension less the Army's .620 tenon: std.ar15.barrel_extension_length, std.ar15.barrel_tenon_length), as the catalog's other 5.56 barrels take it: the sellers state an M4 extension (Huckleberry: \"Barrel Extension M4 Feedramps\"; Primary Arms: \"M4 feed ramps\") and nothing of its size."},"overall_length":{"label":"End to end, the extension's rear to the muzzle","kind":"length","measurements":[{"id":"photo","value":14.226,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/geissele-139-chf-barrel aaf30d1a864c (Primary Arms' gallery, 05-2989_02: the barrel level on white, the muzzle at the right, the gas port, the index pin and the G toward the lens, 2200 x 1467)","scaleRef":"its gas block journal as the published .750 (52.25 px of radius over columns 1474 to 1614, the silhouette at grey 235: 139.34 px/in) and its extension's body as the Army's .999 (68.65 px over columns 114 to 224: 137.44 px/in), a line between the two along the photo, which is yawed (its scale 2.0% greater at the muzzle than at the breech): 137.4 to 140.1 px/in at this station","method":"its two end faces, each behind its rim's arc: the muzzle's at column 2093.1 (the tip at 2105.8, a 12.8 px arc at radius 35.1: seen from 20.0° off square), the extension's rear at 119.6 (the tip at 93.5, a 26.0 px arc at radius 68.7: 20.8°); through the line of scales, the lens's axis at column 1099.5 (.cache/batch46/geissele-145-chf-barrel/measure.py on the photo mirrored; the columns here are the photo's own)","via":"harvest"}},{"id":"published","value":14.401,"unit":"in","pm":0.07,"source":{"type":"derived","expr":"{.length} + {.extension_behind_breech}","via":"harvest"}}],"adopt":{"from":"published","reason":"Lengths at the published length's scale, as the catalog's other barrels: at that scale the gas port, which this photo shows, is 9.18 ahead of the receiver's face, where a mid-length chart has it (9.18) and Aero's is (9.17), and the thread comes out 0.62 long (the Army's .63)."},"note":"The photo, by the scales its journal and its extension give, has the two end faces 1.2% nearer than the published length gives (the 14.5 in barrel's photo, 0.6%): at grey 235 a black part's lit edge is taken a little wide, and its diameters with it. The published length is the scale for lengths. The difference is also about what a length taken from the bolt's face, an eighth behind the breech end, would make it (14.276): no page says which the 13.9 is, and the ± covers it. The rendering has 14.35."},"extension_rear_x":{"label":"The barrel extension's rear end, from the flange's rear face (negative: inside the receiver)","kind":"length","measurements":[{"id":"photo","value":-0.989,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-139-chf-barrel aaf30d1a864c (Primary Arms' gallery, 05-2989_02: the barrel level on white, the muzzle at the right, the gas port, the index pin and the G toward the lens, 2200 x 1467)","scaleRef":"its end faces (columns 119.6 and 2093.1, each behind its rim's arc), 14.226 in apart by the line of scales its journal and its extension give, the lens's axis taken at the image's middle (column 1099.5): stretched by 1.0123 to overall_length (14.401)","method":"the rear end's face (column 119.6, behind its rim's 26 px arc) to the flange's rear face (column 252.7: the silhouette's edge between the flange's rim and the extension's body is the flange's rear rim seen from 18° off square, and columns 239 to 249 each put the face there within a pixel)","via":"harvest"}}],"note":"The reference CAD set's extension has 0.990 here (1.121 less its 0.131 flange)."},"flange_front_x":{"label":"The extension flange's front face, ahead of its rear face (the flange's thickness)","kind":"length","measurements":[{"id":"photo","value":0.117,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-139-chf-barrel aaf30d1a864c (Primary Arms' gallery, 05-2989_02: the barrel level on white, the muzzle at the right, the gas port, the index pin and the G toward the lens, 2200 x 1467)","scaleRef":"its end faces (columns 119.6 and 2093.1, each behind its rim's arc), 14.226 in apart by the line of scales its journal and its extension give, the lens's axis taken at the image's middle (column 1099.5): stretched by 1.0123 to overall_length (14.401)","method":"the flange's rear face (column 252.7) to its front face (column 268.5: the front rim's far arc, columns 275 to 281, each within a pixel of it)","via":"harvest"}}],"note":"The reference CAD set's flange is 0.131 thick (std.ar15.barrel_extension_flange_thickness), and the rendering's the same (0.13); the 14.5 in barrel's own photo reads 0.117."},"flange_od":{"label":"The barrel extension's flange, its diameter","kind":"length","measurements":[{"id":"photo","value":1.167,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/geissele-139-chf-barrel aaf30d1a864c (Primary Arms' gallery, 05-2989_02: the barrel level on white, the muzzle at the right, the gas port, the index pin and the G toward the lens, 2200 x 1467)","scaleRef":"its gas block journal as the published .750 (52.25 px of radius over columns 1474 to 1614, the silhouette at grey 235: 139.34 px/in) and its extension's body as the Army's .999 (68.65 px over columns 114 to 224: 137.44 px/in), a line between the two along the photo, which is yawed (its scale 2.0% greater at the muzzle than at the breech): 137.56 px/in at this station","method":"the silhouette's widest, columns 249 to 265: 80.29 px of radius","via":"harvest"}}],"note":"At its own station's scale. The reference CAD set's is 1.170; the 14.5 in barrel's photo reads 1.168; the rendering of this barrel has 1.149 (a rendering's: both photographs have it larger)."},"extension_od":{"label":"The barrel extension's body, its diameter (what goes into the receiver)","kind":"length","measurements":[{"id":"tdp","value":0.999,"unit":"in","pm":0.001,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_od}","via":"user"},"note":"The Army's limit on the assembly drawing (8448548: \"DIAMETER NOT TO EXCEED .9990 FOR THIS LENGTH AFTER ASSEMBLY AND BEFORE FINISH\"), as read for BCM's barrel's ledger, where the drawing and its page are cited."}],"note":"Not read off this photo: with the journal it is what the photo's scale is taken from (at the journal's scale alone it reads .985, which is how the photo's yaw shows). The rendering has .9996 at its journal's scale."},"chamber_od":{"label":"The chamber section's diameter, ahead of the flange","kind":"length","measurements":[{"id":"photo","value":0.979,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/geissele-139-chf-barrel aaf30d1a864c (Primary Arms' gallery, 05-2989_02: the barrel level on white, the muzzle at the right, the gas port, the index pin and the G toward the lens, 2200 x 1467)","scaleRef":"its gas block journal as the published .750 (52.25 px of radius over columns 1474 to 1614, the silhouette at grey 235: 139.34 px/in) and its extension's body as the Army's .999 (68.65 px over columns 114 to 224: 137.44 px/in), a line between the two along the photo, which is yawed (its scale 2.0% greater at the muzzle than at the breech): 137.65 px/in at this station","method":"columns 284 to 359: 67.41 px of radius","via":"harvest"}}],"note":"A plain cylinder from the flange's front face to chamber_front_x. The rendering has 0.978."},"chamber_front_x":{"label":"Where the chamber section ends and the barrel begins to narrow, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":0.916,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-139-chf-barrel aaf30d1a864c (Primary Arms' gallery, 05-2989_02: the barrel level on white, the muzzle at the right, the gas port, the index pin and the G toward the lens, 2200 x 1467)","scaleRef":"its end faces (columns 119.6 and 2093.1, each behind its rim's arc), 14.226 in apart by the line of scales its journal and its extension give, the lens's axis taken at the image's middle (column 1099.5): stretched by 1.0123 to overall_length (14.401)","method":"the flange's rear face (column 252.7) to where a line through the chamber section's radius (columns 284 to 359) meets a line through the cone's (columns 389 to 539): column 376.3","via":"harvest"}}]},"taper_rear_x":{"label":"Where the cone ahead of the chamber ends and the long taper begins, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":2.324,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-139-chf-barrel aaf30d1a864c (Primary Arms' gallery, 05-2989_02: the barrel level on white, the muzzle at the right, the gas port, the index pin and the G toward the lens, 2200 x 1467)","scaleRef":"its end faces (columns 119.6 and 2093.1, each behind its rim's arc), 14.226 in apart by the line of scales its journal and its extension give, the lens's axis taken at the image's middle (column 1099.5): stretched by 1.0123 to overall_length (14.401)","method":"the flange's rear face (column 252.7) to where a line through the cone's radius (columns 389 to 539) meets a line through the long taper's (columns 599 to 1339): column 566.8","via":"harvest"}}]},"taper_rear_od":{"label":"The long taper's diameter at its rear end (the Geissele Taper Profile's thick end)","kind":"length","measurements":[{"id":"photo","value":0.726,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/geissele-139-chf-barrel aaf30d1a864c (Primary Arms' gallery, 05-2989_02: the barrel level on white, the muzzle at the right, the gas port, the index pin and the G toward the lens, 2200 x 1467)","scaleRef":"its gas block journal as the published .750 (52.25 px of radius over columns 1474 to 1614, the silhouette at grey 235: 139.34 px/in) and its extension's body as the Army's .999 (68.65 px over columns 114 to 224: 137.44 px/in), a line between the two along the photo, which is yawed (its scale 2.0% greater at the muzzle than at the breech): 137.99 px/in at this station","method":"the two lines' crossing at column 566.8: 50.06 px of radius","via":"harvest"}},{"id":"rendering","value":0.718,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/geissele-139-chf-barrel cdb5a8bf2069 (C. Stephens Gun Works' picture, GEI05-2989_1_HR.jpg: a rendering of the barrel from above, the muzzle at the right, 2000 x 2000)","scaleRef":"its journal as the published .750 (50.79 px of radius over columns 1374 to 1494, the picture read at grey 200: 135.43 px/in); at that scale its extension is .9996 and its end faces, behind their rims' arcs, 14.35 in apart (the published length gives 14.40)","method":"where a line through the cone's radius meets a line through the long taper's: 48.62 px of radius against the journal's 50.79","via":"harvest"}}],"adopt":{"from":"photo","reason":"The photograph of the barrel; the rendering, read at another grey level, is within the two readings' ±."},"note":"The 14.5 in barrel's own photo has 0.725 here."},"taper_front_x":{"label":"Where the long taper ends and the barrel flares to the gas block's collar, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":8.276,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-139-chf-barrel aaf30d1a864c (Primary Arms' gallery, 05-2989_02: the barrel level on white, the muzzle at the right, the gas port, the index pin and the G toward the lens, 2200 x 1467)","scaleRef":"its end faces (columns 119.6 and 2093.1, each behind its rim's arc), 14.226 in apart by the line of scales its journal and its extension give, the lens's axis taken at the image's middle (column 1099.5): stretched by 1.0123 to overall_length (14.401)","method":"the flange's rear face (column 252.7) to where a line through the long taper's radius (columns 599 to 1339) meets a line through the flare's (columns 1384 to 1424): column 1380.4","via":"harvest"}}],"note":"Between the two the barrel narrows from 0.726 to 0.665 in 5.95 in: one straight line on both edges of the photo (0.0046 px of radius a pixel over 740 columns). This is the profile the sellers call \"Geissele Taper Profile\": no cylinder between the chamber and the gas block."},"taper_front_od":{"label":"The long taper's diameter at its front end (the barrel's thinnest behind the gas block)","kind":"length","measurements":[{"id":"photo","value":0.665,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/geissele-139-chf-barrel aaf30d1a864c (Primary Arms' gallery, 05-2989_02: the barrel level on white, the muzzle at the right, the gas port, the index pin and the G toward the lens, 2200 x 1467)","scaleRef":"its gas block journal as the published .750 (52.25 px of radius over columns 1474 to 1614, the silhouette at grey 235: 139.34 px/in) and its extension's body as the Army's .999 (68.65 px over columns 114 to 224: 137.44 px/in), a line between the two along the photo, which is yawed (its scale 2.0% greater at the muzzle than at the breech): 139.11 px/in at this station","method":"the two lines' crossing at column 1380.4: 46.28 px of radius","via":"harvest"}},{"id":"rendering","value":0.658,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/geissele-139-chf-barrel cdb5a8bf2069 (C. Stephens Gun Works' picture, GEI05-2989_1_HR.jpg: a rendering of the barrel from above, the muzzle at the right, 2000 x 2000)","scaleRef":"its journal as the published .750 (50.79 px of radius over columns 1374 to 1494, the picture read at grey 200: 135.43 px/in); at that scale its extension is .9996 and its end faces, behind their rims' arcs, 14.35 in apart (the published length gives 14.40)","method":"where a line through the long taper's radius meets a line through the flare's: 44.55 px of radius against the journal's 50.79","via":"harvest"}}],"adopt":{"from":"photo","reason":"The photograph of the barrel; the rendering, read at another grey level, is within the two readings' ±."},"note":"The 14.5 in barrel's own photo has 0.663 here."},"collar_od":{"label":"The collar behind the gas block journal, its diameter","kind":"length","measurements":[{"id":"photo","value":0.842,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/geissele-139-chf-barrel aaf30d1a864c (Primary Arms' gallery, 05-2989_02: the barrel level on white, the muzzle at the right, the gas port, the index pin and the G toward the lens, 2200 x 1467)","scaleRef":"its gas block journal as the published .750 (52.25 px of radius over columns 1474 to 1614, the silhouette at grey 235: 139.34 px/in) and its extension's body as the Army's .999 (68.65 px over columns 114 to 224: 137.44 px/in), a line between the two along the photo, which is yawed (its scale 2.0% greater at the muzzle than at the breech): 139.21 px/in at this station","method":"columns 1443 to 1457: 58.62 px of radius","via":"harvest"}}],"note":"A gas block's rear face comes back to its front face. Its rear side isn't a face: it flares down to the taper over 0.47 in, a concave curve. A slot a sixteenth of an inch wide runs along its top, in line with the port (nine pixels across in this photo): the \"indexing notch\" a buyer of the 14.5 in barrel mentions. The rendering has the collar 0.834."},"collar_rear_x":{"label":"Where the collar's full diameter ends, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":8.748,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-139-chf-barrel aaf30d1a864c (Primary Arms' gallery, 05-2989_02: the barrel level on white, the muzzle at the right, the gas port, the index pin and the G toward the lens, 2200 x 1467)","scaleRef":"its end faces (columns 119.6 and 2093.1, each behind its rim's arc), 14.226 in apart by the line of scales its journal and its extension give, the lens's axis taken at the image's middle (column 1099.5): stretched by 1.0123 to overall_length (14.401)","method":"the flange's rear face (column 252.7) to the last column at the collar's full radius (1445.5: 58.6 px, 58.3 a column and a half on and falling)","via":"harvest"}}]},"journal_rear_x":{"label":"The gas block journal's rear shoulder (the collar's front face) ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":8.887,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-139-chf-barrel aaf30d1a864c (Primary Arms' gallery, 05-2989_02: the barrel level on white, the muzzle at the right, the gas port, the index pin and the G toward the lens, 2200 x 1467)","scaleRef":"its end faces (columns 119.6 and 2093.1, each behind its rim's arc), 14.226 in apart by the line of scales its journal and its extension give, the lens's axis taken at the image's middle (column 1099.5): stretched by 1.0123 to overall_length (14.401)","method":"the flange's rear face (column 252.7) to the collar's front face (column 1464.6: the silhouette's step is at 1467.1 at half height, 2.4 px toward the muzzle by its rim's arc, the lens being 7° toward the breech from there; on the near side the face shows as a dark line at column 1473, the same face 8 px out by the same arc)","via":"harvest"}},{"id":"rendering","value":8.889,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-139-chf-barrel cdb5a8bf2069 (C. Stephens Gun Works' picture, GEI05-2989_1_HR.jpg: a rendering of the barrel from above, the muzzle at the right, 2000 x 2000)","scaleRef":"its end faces, behind their rims' arcs, 1943.4 px apart as overall_length (14.401): 134.95 px/in","method":"its flange's rear face to its collar's front face, each read off the silhouette behind its rim's arc: 1199.6 px","via":"harvest"}}],"adopt":{"from":"photo","reason":"The photograph of the barrel; the rendering agrees to two thousandths."},"note":"A gas block's rear face comes back to this shoulder. The 14.5 in barrel's own photo has 8.882; the catalog's 16 in mid-length barrels 8.85 to 8.87."},"gas_port_x":{"label":"The gas port ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":9.177,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-139-chf-barrel aaf30d1a864c (Primary Arms' gallery, 05-2989_02: the barrel level on white, the muzzle at the right, the gas port, the index pin and the G toward the lens, 2200 x 1467)","scaleRef":"its end faces (columns 119.6 and 2093.1, each behind its rim's arc), 14.226 in apart by the line of scales its journal and its extension give, the lens's axis taken at the image's middle (column 1099.5): stretched by 1.0123 to overall_length (14.401)","method":"the flange's rear face (column 252.7) to the port's centre: seen at column 1512.1 on top of the journal, which on the near side is 7.5 px toward the muzzle of its station (the lens stands 8° toward the breech from there): column 1504.6","via":"harvest"}}],"note":"The port itself: in Primary Arms' side photo it faces the lens, with the index pin, the collar's slot and the G in one line. 0.29 ahead of the journal's rear shoulder (BCM's 0.28, a mid-length chart's .300). Checks: Aero's mid-length port is at 9.17, BCM's 9.13, Bear Creek's 9.14, the chart's 9.18, the 14.5 in sibling's (read at its dimple, on its own photo) 9.168: mid-length by the photo as by every seller's word. A carbine-length port would be about two inches further back. Huckleberry: \".750\" gas block diameter with a precision-machined dimple for secure mounting\": the dimple is underneath, and not in this photo."},"journal_front_x":{"label":"The gas block journal's front end (where the barrel begins to narrow) ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":9.933,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-139-chf-barrel aaf30d1a864c (Primary Arms' gallery, 05-2989_02: the barrel level on white, the muzzle at the right, the gas port, the index pin and the G toward the lens, 2200 x 1467)","scaleRef":"its end faces (columns 119.6 and 2093.1, each behind its rim's arc), 14.226 in apart by the line of scales its journal and its extension give, the lens's axis taken at the image's middle (column 1099.5): stretched by 1.0123 to overall_length (14.401)","method":"the flange's rear face (column 252.7) to where a line through the journal's radius (columns 1474 to 1614) meets a line through the cone's ahead of it (columns 1634 to 1699): column 1609.2","via":"harvest"}}],"note":"The journal is 1.05 long. Ahead of it the barrel narrows to the muzzle section over 0.66 in, a cone (no step)."},"muzzle_run_rear_x":{"label":"Where the cone ahead of the journal ends and the muzzle section begins, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":10.59,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-139-chf-barrel aaf30d1a864c (Primary Arms' gallery, 05-2989_02: the barrel level on white, the muzzle at the right, the gas port, the index pin and the G toward the lens, 2200 x 1467)","scaleRef":"its end faces (columns 119.6 and 2093.1, each behind its rim's arc), 14.226 in apart by the line of scales its journal and its extension give, the lens's axis taken at the image's middle (column 1099.5): stretched by 1.0123 to overall_length (14.401)","method":"the flange's rear face (column 252.7) to where a line through the cone's radius (columns 1634 to 1699) meets a line through the muzzle section's (columns 1734 to 1954): column 1700.3","via":"harvest"}}]},"muzzle_run_od":{"label":"The muzzle section's diameter, between the cone ahead of the journal and the ring behind the shoulder","kind":"length","measurements":[{"id":"photo","value":0.67,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/geissele-139-chf-barrel aaf30d1a864c (Primary Arms' gallery, 05-2989_02: the barrel level on white, the muzzle at the right, the gas port, the index pin and the G toward the lens, 2200 x 1467)","scaleRef":"its gas block journal as the published .750 (52.25 px of radius over columns 1474 to 1614, the silhouette at grey 235: 139.34 px/in) and its extension's body as the Army's .999 (68.65 px over columns 114 to 224: 137.44 px/in), a line between the two along the photo, which is yawed (its scale 2.0% greater at the muzzle than at the breech): 139.75 px/in at this station","method":"columns 1734 to 1954: 46.82 px of radius","via":"harvest"}}],"note":"A cylinder 1.9 in long: this is where the barrel is shorter than the 14.5 in one (2.5 in there). The rendering has 0.666."},"muzzle_ring_rear_x":{"label":"The rear end of the ring behind the muzzle shoulder, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":12.57,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-139-chf-barrel aaf30d1a864c (Primary Arms' gallery, 05-2989_02: the barrel level on white, the muzzle at the right, the gas port, the index pin and the G toward the lens, 2200 x 1467)","scaleRef":"its end faces (columns 119.6 and 2093.1, each behind its rim's arc), 14.226 in apart by the line of scales its journal and its extension give, the lens's axis taken at the image's middle (column 1099.5): stretched by 1.0123 to overall_length (14.401)","method":"the flange's rear face (column 252.7) to the last column at the ring's radius (1975.5: 48.8 px; 48.5 a column on and falling to 46.9 at 1964)","via":"harvest"}}],"note":"The ring is 0.22 long and comes down to the muzzle section over another 0.08 in (columns 1964 to 1975), a chamfer and not a step. Geissele's G is on the muzzle section just behind it."},"muzzle_ring_foot_x":{"label":"Where the ring's rear chamfer meets the muzzle section, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":12.487,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-139-chf-barrel aaf30d1a864c (Primary Arms' gallery, 05-2989_02: the barrel level on white, the muzzle at the right, the gas port, the index pin and the G toward the lens, 2200 x 1467)","scaleRef":"its end faces (columns 119.6 and 2093.1, each behind its rim's arc), 14.226 in apart by the line of scales its journal and its extension give, the lens's axis taken at the image's middle (column 1099.5): stretched by 1.0123 to overall_length (14.401)","method":"the flange's rear face (column 252.7) to the first column at the muzzle section's radius behind the ring (1964.0: 46.9 px, as at 1960)","via":"harvest"}}]},"shoulder_x":{"label":"The muzzle shoulder ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":12.792,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-139-chf-barrel aaf30d1a864c (Primary Arms' gallery, 05-2989_02: the barrel level on white, the muzzle at the right, the gas port, the index pin and the G toward the lens, 2200 x 1467)","scaleRef":"its end faces (columns 119.6 and 2093.1, each behind its rim's arc), 14.226 in apart by the line of scales its journal and its extension give, the lens's axis taken at the image's middle (column 1099.5): stretched by 1.0123 to overall_length (14.401)","method":"the flange's rear face (column 252.7) to the shoulder's face (column 2006.5: the silhouette's step is at 2014.3 at half height, 8 px toward the muzzle by the ring's rim's arc, the lens being 18° toward the breech from there; columns 2012 to 2016 each put the face at 2006 to 2007)","via":"harvest"}}],"note":"Where the thread begins: a muzzle device or its washer seats here, on the ring's front face. 0.59 in behind the 14.5 in barrel's (13.381), for 0.6 in of length."},"thread_length":{"label":"The muzzle thread's length","kind":"length","measurements":[{"id":"photo","value":0.62,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-139-chf-barrel aaf30d1a864c (Primary Arms' gallery, 05-2989_02: the barrel level on white, the muzzle at the right, the gas port, the index pin and the G toward the lens, 2200 x 1467)","scaleRef":"its end faces (columns 119.6 and 2093.1, each behind its rim's arc), 14.226 in apart by the line of scales its journal and its extension give, the lens's axis taken at the image's middle (column 1099.5): stretched by 1.0123 to overall_length (14.401)","method":"the shoulder's face (column 2006.5) to the muzzle's face (column 2093.1, behind its rim's 12.8 px arc)","via":"harvest"}}],"note":"The Army's barrel has .63 here (8448549 sheet 1, from the shoulder to the muzzle); the 14.5 in barrel's own photo reads 0.619."},"muzzle_od":{"label":"The diameter behind the muzzle thread","kind":"length","measurements":[{"id":"photo","value":0.701,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/geissele-139-chf-barrel aaf30d1a864c (Primary Arms' gallery, 05-2989_02: the barrel level on white, the muzzle at the right, the gas port, the index pin and the G toward the lens, 2200 x 1467)","scaleRef":"its gas block journal as the published .750 (52.25 px of radius over columns 1474 to 1614, the silhouette at grey 235: 139.34 px/in) and its extension's body as the Army's .999 (68.65 px over columns 114 to 224: 137.44 px/in), a line between the two along the photo, which is yawed (its scale 2.0% greater at the muzzle than at the breech): 139.95 px/in at this station","method":"columns 1977 to 1999: 49.02 px of radius (0.7005)","via":"harvest"}}],"note":"The ring behind the shoulder; the muzzle section behind it is 0.670 (muzzle_run_od). The rendering has the ring 0.695; the 14.5 in barrel's photo 0.699."},"bore_d":{"label":"The bore's diameter (across the lands)","kind":"length","measurements":[{"id":"tdp","value":0.219,"unit":"in","pm":0.001,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.bore_d}","via":"user"},"note":"The Army's barrel drawing (8448549 sheet 2, Section U-U: \".219 DIA+.001\"), as read for BCM's barrel's ledger, where the drawing and its page are cited."}],"note":"The cartridge's, for the hole the model cuts: the sellers state \"Chambered in 5.56 NATO\" and no bore."},"index_pin_d":{"label":"The barrel indexing pin's diameter","kind":"length","measurements":[{"id":"tdp","value":0.12525,"unit":"in","pm":0.00025,"source":{"type":"derived","expr":"{bca-556-16-mid-barrel.index_pin_d}","via":"user"},"note":"The Army's own part (8448551, Pin, Barrel Indexing: \".1255 DIA -.0005\"), as read for Bear Creek's barrel's ledger, where the drawing and its page are cited."}]},"index_pin_protrusion":{"label":"The barrel indexing pin's top above the extension's surface","kind":"length","measurements":[{"id":"tdp","value":0.094,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{bca-556-16-mid-barrel.index_pin_protrusion}","via":"user"},"note":"The Army's assembly drawing (8448548, Section A-A: \".094 MAX\"), as read for Bear Creek's barrel's ledger, where the drawing and its page are cited."}],"note":"A limit, and the model draws the pin at it. In Primary Arms' side photo the pin faces the lens: it isn't on the silhouette."},"index_pin_x":{"label":"The barrel indexing pin's axis behind the flange's rear face","kind":"length","measurements":[{"id":"photo","value":0.077,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/geissele-139-chf-barrel aaf30d1a864c (Primary Arms' gallery, 05-2989_02: the barrel level on white, the muzzle at the right, the gas port, the index pin and the G toward the lens, 2200 x 1467)","scaleRef":"its end faces (columns 119.6 and 2093.1, each behind its rim's arc), 14.226 in apart by the line of scales its journal and its extension give, the lens's axis taken at the image's middle (column 1099.5): stretched by 1.0123 to overall_length (14.401)","method":"the pin's round top, 15 px across, its centre seen at column 216.3; its top stands 81.6 px toward the lens from the axis (the extension's radius and index_pin_protrusion), which 18° off square is 25.8 px toward the breech of its station: column 242.1, 10.6 px behind the flange's rear face (252.7)","via":"harvest"}}],"note":"The pin stands against the flange (half its diameter, 0.063, would have it touching), in line with the gas port and the collar's slot."},"extension_mouth_d":{"label":"The barrel extension's rear opening, its diameter at the rear face","kind":"length","measurements":[{"id":"model","value":0.77,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_mouth_d}","via":"user"}}],"note":"The inside of a mil-spec M4 extension as the reference CAD set has it, for how the rear end looks (the sellers: \"Barrel Extension M4 Feedramps\"; Huckleberry's pictures of this barrel's breech, e8a65f4c9001 and e01d5d5636fe, show the lugs and the ramps). Appearance only; the six figures of the opening are the readings made for BCM's barrel's ledger, where the file and the method are cited."},"extension_mouth_chamfer":{"label":"The rear opening's chamfer, its depth (at 45°, also how far it narrows the opening's radius)","kind":"length","measurements":[{"id":"model","value":0.045,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_mouth_chamfer}","via":"user"}}]},"extension_lug_bore_d":{"label":"The circle the extension's locking lugs leave between their tips","kind":"length","measurements":[{"id":"model","value":0.572,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_lug_bore_d}","via":"user"}}]},"extension_lug_depth":{"label":"The locking lugs' front faces, ahead of the extension's rear end","kind":"length","measurements":[{"id":"model","value":0.214,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_lug_depth}","via":"user"}}]},"extension_recess_d":{"label":"The recess ahead of the lugs, which the bolt's lugs turn in: its diameter","kind":"length","measurements":[{"id":"model","value":0.83,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_recess_d}","via":"user"}}]},"extension_recess_depth":{"label":"The recess's front end, ahead of the extension's rear end","kind":"length","measurements":[{"id":"model","value":0.595,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_recess_depth}","via":"user"}}]},"thread_major_d":{"label":"The muzzle thread's major diameter (its crests)","kind":"length","measurements":[{"id":"tdp","value":0.4957,"unit":"in","pm":0.0033,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.thread_major_d}","via":"user"},"note":"8448549 sheet 1, Section M-M: \"1/2-28 UNEF-2A MAJOR DIA .4989/.4924\", as read for BCM's barrel's ledger."}],"note":"The Army barrel's 1/2-28 thread, for the 1/2 x 28 the sellers state: what the model's thread is drawn at. The photo's silhouette of the thread is 0.501 at its station's scale (70.2 px at 140.05 px/in)."},"thread_minor_d":{"label":"The muzzle thread's minor diameter (its roots)","kind":"length","measurements":[{"id":"tdp","value":0.4551,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.thread_minor_d}","via":"user"},"note":"8448549 sheet 1, Section M-M: \"MINOR DIA .4551 MAX\", as read for BCM's barrel's ledger."}]},"thread_pitch":{"label":"The muzzle thread's pitch","kind":"length","measurements":[{"id":"primary-arms","value":0.03571,"unit":"in","pm":0.00005,"stated":"Thread Pattern 1/2 X 28","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics CHF Chrome Lined 5.56 AR-15 Barrel - Mid-Length - Tapered - 13.9\" (05-2989), Specifications; its Features: \"Threaded 1/2x28\"","url":"https://www.primaryarms.com/geissele-automatics-5-56-chf-mid-length-taper-profile-ar-15-barrel-chrome-lined-13-9in","retrieved":"2026-10-06","via":"harvest"}},{"id":"huckleberry","value":0.03571,"unit":"in","pm":0.00005,"stated":"Muzzle Thread Pitch 1/2 x 28","source":{"type":"spec","publisher":"retailer","name":"Huckleberry Arms, Geissele CHF Chrome Lined Barrel 5.56 NATO – 13.9\" (Product Code 05-2989), Technical Specs","url":"https://www.huckleberryarms.com/geissele-chf-chrome-lined-barrel-556-13-9-inch-p/05-2989.htm","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"primary-arms","reason":"Two sellers' pages state the one thread."},"note":"28 threads to the inch, by the sellers' statement: not a measurement of this barrel."},"collar_slot_w":{"label":"The slot along the collar's top, in line with the gas port: its width","kind":"length","measurements":[{"id":"photo","value":0.063,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-139-chf-barrel aaf30d1a864c (Primary Arms' gallery, 05-2989_02: the barrel level on white, the muzzle at the right, the gas port, the index pin and the G toward the lens, 2200 x 1467)","scaleRef":"its gas block journal as the published .750 (the silhouette at grey 235: 139.2 px/in at the collar)","method":"the slot's two edges on the collar's top, rows 731 to 739 on an eight-fold enlargement: 8.75 px","via":"harvest"}}],"note":"A slot with a round rear end, from the collar's front face back along its top for the collar's whole length. Not drawn: its depth isn't sourced (collar_slot_depth)."},"collar_slot_depth":{"label":"The slot along the collar's top: its depth","kind":"length","measurements":[],"note":"No source: the photo looks straight down into it. Not drawn until a figure or a view from the muzzle is on file."},"dimple_depth":{"label":"The dimple under the journal, for a gas block's set screw: its depth","kind":"length","measurements":[],"note":"Huckleberry: \".750\" gas block diameter with a precision-machined dimple for secure mounting\". Primary Arms' close photo of the journal's underside (308babea3e35) shows it, a drilled spot with a coned floor just ahead of the collar, from an angle: neither its size nor its depth is read. Not drawn."},"outline_flange_od":{"label":"The flange as the side photo has it at the journal's scale: the traced outline's scale reference","kind":"length","measurements":[{"id":"photo","value":1.1525,"unit":"in","pm":0.007,"source":{"type":"photo","photo":"references/geissele-139-chf-barrel aaf30d1a864c (Primary Arms' gallery, 05-2989_02: the barrel level on white, the muzzle at the right, the gas port, the index pin and the G toward the lens, 2200 x 1467)","scaleRef":"its gas block journal's diameter as the published .750 (the silhouette at grey 235: 52.25 px of radius over columns 1474 to 1614, 139.34 px/in)","method":"the silhouette's widest, columns 249 to 265: 80.29 px of radius against the journal's 52.25","via":"harvest"}}],"note":"Not the flange's size (flange_od, 1.167): the photo is yawed, and at the journal's scale everything at the breech end reads 1.4% small. The traced outline is at this one scale throughout; the model corrects it by the four figures that follow."},"outline_extension_od":{"label":"The extension's body as the side photo has it at the journal's scale","kind":"length","measurements":[{"id":"photo","value":0.9854,"unit":"in","pm":0.007,"source":{"type":"photo","photo":"references/geissele-139-chf-barrel aaf30d1a864c (Primary Arms' gallery, 05-2989_02: the barrel level on white, the muzzle at the right, the gas port, the index pin and the G toward the lens, 2200 x 1467)","scaleRef":"its gas block journal's diameter as the published .750 (the silhouette at grey 235: 52.25 px of radius over columns 1474 to 1614, 139.34 px/in)","method":"the extension's body, columns 114 to 224: 68.65 px of radius against the journal's 52.25","via":"harvest"}}],"note":"Against extension_od (.999) this is how far the photo's scale has fallen between the journal and the extension: 1.4% in 9.87 in."},"outline_extension_x":{"label":"The middle of the extension's body in the traced outline's own frame (from the silhouette's rear tip, at the journal's scale)","kind":"length","measurements":[{"id":"photo","value":0.542,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-139-chf-barrel aaf30d1a864c (Primary Arms' gallery, 05-2989_02: the barrel level on white, the muzzle at the right, the gas port, the index pin and the G toward the lens, 2200 x 1467)","scaleRef":"the traced outline's scale: 139.34 px/in","method":"column 169, the middle of the stretch outline_extension_od is read on, from the silhouette's rear tip (column 93.5)","via":"harvest"}}]},"outline_journal_x":{"label":"The middle of the gas block journal in the traced outline's own frame (from the silhouette's rear tip, at the journal's scale)","kind":"length","measurements":[{"id":"photo","value":10.41,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-139-chf-barrel aaf30d1a864c (Primary Arms' gallery, 05-2989_02: the barrel level on white, the muzzle at the right, the gas port, the index pin and the G toward the lens, 2200 x 1467)","scaleRef":"the traced outline's scale: 139.34 px/in","method":"column 1544, the middle of the stretch the journal's .750 is read on, from the silhouette's rear tip (column 93.5)","via":"harvest"}}]},"outline_axis_x":{"label":"Where the lens's axis meets the photo, in the traced outline's own frame (from the silhouette's rear tip, at the journal's scale)","kind":"length","measurements":[{"id":"photo","value":7.22,"unit":"in","pm":0.25,"source":{"type":"photo","photo":"references/geissele-139-chf-barrel aaf30d1a864c (Primary Arms' gallery, 05-2989_02: the barrel level on white, the muzzle at the right, the gas port, the index pin and the G toward the lens, 2200 x 1467)","scaleRef":"the traced outline's scale: 139.34 px/in","method":"column 1099.5, the middle of the image's 2200, from the silhouette's rear tip (column 93.5)","via":"harvest"}}],"note":"Taken at the image's middle, as tools/trace.py's tube calibration takes it: a crop would move it. The rims' arcs put the point the lens stands square to the barrel at column 1127, 27 px from it. The ± is what a quarter of an inch of crop would be."},"outline_rear_face":{"label":"outline rear face","kind":"length","measurements":[{"id":"photo","value":0.184,"unit":"in","pm":0.011,"source":{"type":"photo","photo":"references/geissele-139-chf-barrel aaf30d1a864c (Primary Arms' gallery, 05-2989_02: the barrel level on white, the muzzle at the right, 2200 x 1467)","scaleRef":"scale from geissele-139-chf-barrel.outline_flange_od = 1.1525 in (y-extent 160 px → 138.8 px/in)","method":"the min end's face: the silhouette's tip at 0.002 less its rim's arc, 0.182 in of sag at radius 0.489813 (the end is seen from 20.4° off square; arc fitted over 121 rows, rms 0.002) of the traced outline (tools/trace.py); the extension's rear face in the outline's own frame (from its rear tip, at the journal's scale)","via":"harvest"}}]},"outline_front_face":{"label":"outline front face","kind":"length","measurements":[{"id":"photo","value":14.406,"unit":"in","pm":0.088,"source":{"type":"photo","photo":"references/geissele-139-chf-barrel aaf30d1a864c (Primary Arms' gallery, 05-2989_02: the barrel level on white, the muzzle at the right, 2200 x 1467)","scaleRef":"scale from geissele-139-chf-barrel.outline_flange_od = 1.1525 in (y-extent 160 px → 138.8 px/in)","method":"the max end's face: the silhouette's tip at 14.494 less its rim's arc, 0.088 in of sag at radius 0.244906 (the end is seen from 19.8° off square; arc fitted over 117 rows, rms 0.002) of the traced outline (tools/trace.py); the muzzle's face in the outline's own frame (from its rear tip, at the journal's scale)","via":"harvest"}}]}}},{"subject":"geissele-145-chf-barrel","title":"Geissele Automatics CHF Chrome Lined Barrel - 5.56 - 14.5\" (05-2985)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"primary-arms","value":1.6,"unit":"lb","pm":0.05,"stated":"1.6 lbs weight","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics CHF Chrome Lined 5.56 AR-15 Barrel - Mid-Length - Tapered - 14.5\" (05-2985), Features; its Specifications: \"Weight 1.6 lbs\"","url":"https://www.primaryarms.com/geissele-automatics-5-56-chf-mid-length-taper-profile-ar-15-barrel-chrome-lined-14-5in","retrieved":"2026-10-06","via":"harvest"}},{"id":"mile-high","value":1.6,"unit":"lb","pm":0.05,"stated":"WEIGHT: 1.6 lbs","source":{"type":"spec","publisher":"retailer","name":"Mile High Shooting Accessories, Geissele: CHF, Chrome Lined Barrel, 5.56 - 14.5\" (SKU 05-2985), Specifications","url":"https://www.milehighshooting.com/geissele-chf-chrome-lined-barrel-5-56-14-5/","retrieved":"2026-10-06","via":"harvest"}},{"id":"rooftop","value":1.6,"unit":"lb","pm":0.005,"stated":"Weight: 1.60 Pounds","source":{"type":"spec","publisher":"retailer","name":"Rooftop Defense, Geissele Automatics 14.5\" 5.56 Hammer-Forged Midlength Barrel (Geissele Part Number 05-2985), Specifications","url":"https://www.rooftopdefense.com/product/geissele-automatics-14-5-5-56-hammer-forged-midlength-barrel/","retrieved":"2026-10-06","via":"harvest"}},{"id":"ar15discounts","value":25.6,"unit":"oz","pm":0.05,"stated":"Weight 25.6 oz","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, Geissele Automatics CHF 5.56 - 14.5\" Chrome Lined Barrel 1:7 Twist - 05-2895 (sic: the title transposes the number; its UPC 810081134910), Additional information; its Description: \"Weight: 1.6 lbs\"","url":"https://ar15discounts.com/products/geissele-automatics-chf-5-56-14-5-chrome-lined-barrel/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"primary-arms","reason":"Four sellers' pages state the one figure (25.6 oz is 1.6 lb); Primary Arms' is the page whose photos the barrel is drawn from. Geissele's own page isn't read."},"note":"Four sellers, one figure, none the maker's own page. A fifth page (Charlie's Custom Clones) has 22.4 oz for \"Geissele Factory 14.5\\\" CHF Barrel\" at another number (MPN 05-1861, UPC 810081130851): another product, not a reading of this one. The model's volume as steel is the check (app/tests/geissele-145-chf-barrel.test.ts)."},"length":{"label":"Barrel length as its sellers state it for the maker","kind":"length","measurements":[{"id":"primary-arms","value":14.5,"unit":"in","pm":0.05,"stated":"Barrel Length 14.5","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics CHF Chrome Lined 5.56 AR-15 Barrel - Mid-Length - Tapered - 14.5\" (05-2985), Specifications; its Features: \"14.5\\\" cold hammer-forged barrel\"","url":"https://www.primaryarms.com/geissele-automatics-5-56-chf-mid-length-taper-profile-ar-15-barrel-chrome-lined-14-5in","retrieved":"2026-10-06","via":"harvest"}},{"id":"mile-high","value":14.5,"unit":"in","pm":0.05,"stated":"LENGTH: 14.5\"","source":{"type":"spec","publisher":"retailer","name":"Mile High Shooting Accessories, Geissele: CHF, Chrome Lined Barrel, 5.56 - 14.5\" (SKU 05-2985), Specifications","url":"https://www.milehighshooting.com/geissele-chf-chrome-lined-barrel-5-56-14-5/","retrieved":"2026-10-06","via":"harvest"}},{"id":"rooftop","value":14.5,"unit":"in","pm":0.05,"stated":"Length: 14.5″","source":{"type":"spec","publisher":"retailer","name":"Rooftop Defense, Geissele Automatics 14.5\" 5.56 Hammer-Forged Midlength Barrel (Geissele Part Number 05-2985), Specifications","url":"https://www.rooftopdefense.com/product/geissele-automatics-14-5-5-56-hammer-forged-midlength-barrel/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"primary-arms","reason":"Three sellers' pages state the one length; none is the maker's own page, which isn't read."},"note":"The nominal length: what the site's federal-law line goes by (D80). No page says between which points; the Army's barrel drawing (8448549) dimensions a barrel from its breech end, inside the extension, to its muzzle, and overall_length takes it so. Under 16 in."},"journal_od":{"label":"The gas block journal's diameter","kind":"length","measurements":[{"id":"primary-arms","value":0.75,"unit":"in","pm":0.0005,"stated":"Gas Seat Diameter .750","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics CHF Chrome Lined 5.56 AR-15 Barrel - Mid-Length - Tapered - 14.5\" (05-2985), Specifications","url":"https://www.primaryarms.com/geissele-automatics-5-56-chf-mid-length-taper-profile-ar-15-barrel-chrome-lined-14-5in","retrieved":"2026-10-06","via":"harvest"}},{"id":"mile-high","value":0.75,"unit":"in","pm":0.0005,"stated":"GAS BLOCK DIAMETER: .750","source":{"type":"spec","publisher":"retailer","name":"Mile High Shooting Accessories, Geissele: CHF, Chrome Lined Barrel, 5.56 - 14.5\" (SKU 05-2985), Specifications","url":"https://www.milehighshooting.com/geissele-chf-chrome-lined-barrel-5-56-14-5/","retrieved":"2026-10-06","via":"harvest"}},{"id":"rooftop","value":0.75,"unit":"in","pm":0.0005,"stated":"Gas Block Journal Diameter: 0.750″","source":{"type":"spec","publisher":"retailer","name":"Rooftop Defense, Geissele Automatics 14.5\" 5.56 Hammer-Forged Midlength Barrel (Geissele Part Number 05-2985), Specifications","url":"https://www.rooftopdefense.com/product/geissele-automatics-14-5-5-56-hammer-forged-midlength-barrel/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"primary-arms","reason":"Three sellers' pages state the one diameter; none is the maker's own page."}},"gas_port_d":{"label":"The gas port's diameter","kind":"length","measurements":[{"id":"mile-high","value":0.076,"unit":"in","pm":0.0005,"stated":"GAS PORT: .076","source":{"type":"spec","publisher":"retailer","name":"Mile High Shooting Accessories, Geissele: CHF, Chrome Lined Barrel, 5.56 - 14.5\" (SKU 05-2985), Specifications","url":"https://www.milehighshooting.com/geissele-chf-chrome-lined-barrel-5-56-14-5/","retrieved":"2026-10-06","via":"harvest"}},{"id":"rooftop","value":0.076,"unit":"in","pm":0.0005,"stated":"Gas Port: 0.076″","source":{"type":"spec","publisher":"retailer","name":"Rooftop Defense, Geissele Automatics 14.5\" 5.56 Hammer-Forged Midlength Barrel (Geissele Part Number 05-2985), Specifications","url":"https://www.rooftopdefense.com/product/geissele-automatics-14-5-5-56-hammer-forged-midlength-barrel/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"mile-high","reason":"Two sellers' pages state the one figure."},"note":"Published for this number (the 13.9 in sibling's is .081, the 12.5 in carbine-gas sibling's .070 on the same sellers' pages)."},"extension_behind_breech":{"label":"The barrel extension's rear end behind the barrel's breech end","kind":"length","measurements":[{"id":"model","value":0.501,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{std.ar15.barrel_extension_behind_breech}","via":"user"}}],"note":"The standard's (the reference CAD set's extension less the Army's .620 tenon: std.ar15.barrel_extension_length, std.ar15.barrel_tenon_length), as the catalog's 16 in barrels take it: Mile High and Primary Arms state an M4 extension (\"BARREL EXTENSION: M4 Feedramps\"; \"Feed Ramps M4\") and nothing of its size."},"overall_length":{"label":"End to end, the extension's rear to the muzzle","kind":"length","measurements":[{"id":"photo","value":14.91,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/geissele-145-chf-barrel dc38f9181866 (Primary Arms' gallery, 05-2985_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"the traced outline's scale: its flange's diameter (flange_od, itself read against the published .750 journal), 133.6 px/in","method":"its two end faces, each behind its rim's arc (tools/trace.py, the seed's `ends` spec: outline_front_face 14.979 less outline_rear_face 0.069), 1992.0 px. A second fit of the two arcs, on the photo's own rows at grey 235, has the faces at columns 103.7 and 2094.8 (1991.2 px, 14.885 at 133.77 px/in): the muzzle's rim seen from 13.5° off square, the extension's rear from 8.6° (.cache/batch46/geissele-145-chf-barrel/measure.py)","via":"harvest"}},{"id":"published","value":15.001,"unit":"in","pm":0.07,"source":{"type":"derived","expr":"{.length} + {.extension_behind_breech}","via":"harvest"}}],"adopt":{"from":"published","reason":"Lengths at the published length's scale, as the catalog's other barrels: at that scale the dimple under the gas port lands 9.17 ahead of the receiver's face, where Aero's mid-length port is (9.17) and a mid-length chart's (9.18), and the thread comes out 0.62 long (the Army's .63)."},"note":"The photo, at its journal's scale with the silhouette read at grey 235, has the two end faces 0.6% nearer than the published length gives (at grey 200, 0.2% further: where a black part's lit edge is taken to end moves its diameters by a pixel in a hundred). The published length is the scale for lengths, the journal the scale for diameters. The difference is near what a length taken from the bolt's face, an eighth behind the breech end, would make it (14.876): no page says which the 14.5 is, and the ± covers it."},"extension_rear_x":{"label":"The barrel extension's rear end, from the flange's rear face (negative: inside the receiver)","kind":"length","measurements":[{"id":"photo","value":-1.001,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-145-chf-barrel dc38f9181866 (Primary Arms' gallery, 05-2985_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its end faces, 1992.0 px apart (columns 103.5 and 2095.5, each behind its rim's arc: outline_front_face and outline_rear_face, tools/trace.py's fit), as overall_length (15.001): 132.79 px/in","method":"the rear end's face (column 2095.5, behind its rim's arc; a second fit of the arc on the photo's own rows has 2094.8) to the flange's rear face (column 1962.5: the silhouette's edge between the flange's rim and the extension's body is the flange's rear rim seen from 7° off square, and columns 1963 to 1967 each put the face there within a pixel)","via":"harvest"}}],"note":"The reference CAD set's extension has 0.990 here (1.121 less its 0.131 flange); BCM's barrel's photo 0.984."},"flange_front_x":{"label":"The extension flange's front face, ahead of its rear face (the flange's thickness)","kind":"length","measurements":[{"id":"photo","value":0.117,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-145-chf-barrel dc38f9181866 (Primary Arms' gallery, 05-2985_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its end faces, 1992.0 px apart (columns 103.5 and 2095.5, each behind its rim's arc: outline_front_face and outline_rear_face, tools/trace.py's fit), as overall_length (15.001): 132.79 px/in","method":"the flange's rear face (column 1962.5) to its front face (column 1946.9: the front rim's far arc, columns 1942 to 1946, each within half a pixel of it)","via":"harvest"}}],"note":"The reference CAD set's flange is 0.131 thick (std.ar15.barrel_extension_flange_thickness); BCM's barrel's reads 0.095. The silhouette's corners (columns 1942.9 and 1966.8 at half height, 0.18 in apart) are the two rims' arcs."},"flange_od":{"label":"The barrel extension's flange, its diameter as the side photo has it at the journal's scale","kind":"length","measurements":[{"id":"photo","value":1.168,"unit":"in","pm":0.007,"source":{"type":"photo","photo":"references/geissele-145-chf-barrel dc38f9181866 (Primary Arms' gallery, 05-2985_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its gas block journal's diameter as the published .750 (the silhouette at grey 235: 50.16 px of radius over columns 655 to 770)","method":"the silhouette's widest, columns 1950 to 1960: 78.10 px of radius against the journal's 50.16 (tools/turned.py at 235 has the ratio 1.5582: 1.169)","via":"harvest"}}],"note":"The scale reference of the traced outline (the silhouette's greatest height). The reference CAD set's is 1.170."},"extension_od":{"label":"The barrel extension's body, its diameter (what goes into the receiver)","kind":"length","measurements":[{"id":"tdp","value":0.999,"unit":"in","pm":0.001,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_od}","via":"user"},"note":"The Army's limit on the assembly drawing (8448548: \"DIAMETER NOT TO EXCEED .9990 FOR THIS LENGTH AFTER ASSEMBLY AND BEFORE FINISH\"), as read for BCM's barrel's ledger, where the drawing and its page are cited."},{"id":"photo","value":1,"unit":"in","pm":0.007,"source":{"type":"photo","photo":"references/geissele-145-chf-barrel dc38f9181866 (Primary Arms' gallery, 05-2985_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its gas block journal's diameter as the published .750 (the silhouette at grey 235: 50.16 px of radius over columns 655 to 770)","method":"the extension's body, columns 2010 to 2085: 66.87 px of radius against the journal's 50.16 (0.9998)","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's limit: an extension over 1.000 doesn't go into a receiver. The photo reads the same within a thousandth."},"note":"The photo agrees with the Army's limit, which says the photo's two ends are at one scale (no yaw to speak of): the journal is 9 in from the extension."},"chamber_od":{"label":"The chamber section's diameter, ahead of the flange","kind":"length","measurements":[{"id":"photo","value":0.983,"unit":"in","pm":0.007,"source":{"type":"photo","photo":"references/geissele-145-chf-barrel dc38f9181866 (Primary Arms' gallery, 05-2985_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its gas block journal's diameter as the published .750 (the silhouette at grey 235: 50.16 px of radius over columns 655 to 770)","method":"columns 1850 to 1930: 65.74 px of radius against the journal's 50.16","via":"harvest"}}],"note":"A plain cylinder from the flange's front face to chamber_front_x (it rises by 0.3 px of radius along its length)."},"chamber_front_x":{"label":"Where the chamber section ends and the barrel begins to narrow, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":0.962,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-145-chf-barrel dc38f9181866 (Primary Arms' gallery, 05-2985_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its end faces, 1992.0 px apart (columns 103.5 and 2095.5, each behind its rim's arc: outline_front_face and outline_rear_face, tools/trace.py's fit), as overall_length (15.001): 132.79 px/in","method":"the flange's rear face (column 1962.5) to where a line through the chamber section's radius (columns 1850 to 1930) meets a line through the cone's (columns 1680 to 1830): column 1834.7","via":"harvest"}}]},"taper_rear_x":{"label":"Where the cone ahead of the chamber ends and the long taper begins, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":2.334,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-145-chf-barrel dc38f9181866 (Primary Arms' gallery, 05-2985_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its end faces, 1992.0 px apart (columns 103.5 and 2095.5, each behind its rim's arc: outline_front_face and outline_rear_face, tools/trace.py's fit), as overall_length (15.001): 132.79 px/in","method":"the flange's rear face (column 1962.5) to where a line through the cone's radius (columns 1680 to 1830) meets a line through the long taper's (columns 900 to 1600): column 1652.6","via":"harvest"}}],"note":"The cone falls 0.129 in of radius in 1.37 in of length (5.3°), straight within half a pixel."},"taper_rear_od":{"label":"The long taper's diameter at its rear end (the Geissele Taper Profile's thick end)","kind":"length","measurements":[{"id":"photo","value":0.725,"unit":"in","pm":0.007,"source":{"type":"photo","photo":"references/geissele-145-chf-barrel dc38f9181866 (Primary Arms' gallery, 05-2985_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its gas block journal's diameter as the published .750 (the silhouette at grey 235: 50.16 px of radius over columns 655 to 770)","method":"the two lines' crossing at column 1652.6: 48.48 px of radius against the journal's 50.16 (the silhouette itself has 48.34 over columns 1630 to 1650: 0.723)","via":"harvest"}}]},"taper_front_x":{"label":"Where the long taper ends and the barrel flares to the gas block's collar, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":8.306,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-145-chf-barrel dc38f9181866 (Primary Arms' gallery, 05-2985_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its end faces, 1992.0 px apart (columns 103.5 and 2095.5, each behind its rim's arc: outline_front_face and outline_rear_face, tools/trace.py's fit), as overall_length (15.001): 132.79 px/in","method":"the flange's rear face (column 1962.5) to where a line through the long taper's radius (columns 900 to 1600) meets a line through the flare's (columns 815 to 855): column 859.5","via":"harvest"}}],"note":"Between the two the barrel narrows from 0.725 to 0.663 in 5.98 in: 0.0052 px of radius a pixel, one straight line within a quarter of a pixel (0.002 in) over 700 columns, read on both edges. This is the profile the sellers call \"Geissele Taper Profile\": no cylinder between the chamber and the gas block."},"taper_front_od":{"label":"The long taper's diameter at its front end (the barrel's thinnest behind the gas block)","kind":"length","measurements":[{"id":"photo","value":0.663,"unit":"in","pm":0.007,"source":{"type":"photo","photo":"references/geissele-145-chf-barrel dc38f9181866 (Primary Arms' gallery, 05-2985_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its gas block journal's diameter as the published .750 (the silhouette at grey 235: 50.16 px of radius over columns 655 to 770)","method":"the two lines' crossing at column 859.5: 44.34 px of radius against the journal's 50.16 (the silhouette itself has 44.33 over columns 875 to 895)","via":"harvest"}}]},"collar_od":{"label":"The collar behind the gas block journal, its diameter","kind":"length","measurements":[{"id":"photo","value":0.844,"unit":"in","pm":0.007,"source":{"type":"photo","photo":"references/geissele-145-chf-barrel dc38f9181866 (Primary Arms' gallery, 05-2985_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its gas block journal's diameter as the published .750 (the silhouette at grey 235: 50.16 px of radius over columns 655 to 770)","method":"columns 788 to 802: 56.41 px of radius against the journal's 50.16 (0.8435; tools/turned.py: 0.844)","via":"harvest"}}],"note":"A gas block's rear face comes back to its front face. Its rear side isn't a face: it flares down to the taper over 0.44 in, a concave curve."},"collar_rear_x":{"label":"Where the collar's full diameter ends, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":8.743,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-145-chf-barrel dc38f9181866 (Primary Arms' gallery, 05-2985_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its end faces, 1992.0 px apart (columns 103.5 and 2095.5, each behind its rim's arc: outline_front_face and outline_rear_face, tools/trace.py's fit), as overall_length (15.001): 132.79 px/in","method":"the flange's rear face (column 1962.5) to the last column at the collar's full radius (801: 56.3 px, 56.1 at 802 and falling)","via":"harvest"}}]},"journal_rear_x":{"label":"The gas block journal's rear shoulder (the collar's front face) ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":8.882,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-145-chf-barrel dc38f9181866 (Primary Arms' gallery, 05-2985_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its end faces, 1992.0 px apart (columns 103.5 and 2095.5, each behind its rim's arc: outline_front_face and outline_rear_face, tools/trace.py's fit), as overall_length (15.001): 132.79 px/in","method":"the flange's rear face (column 1962.5) to the collar's front face (column 783.0: the silhouette's step is at 781.2 at half height, 2 px toward the muzzle by its rim's arc, the lens being 6° toward the breech from there; on the near side the face shows as a dark line at columns 777 to 778, the same face 6 px out by the same arc)","via":"harvest"}}],"note":"A gas block's rear face comes back to this shoulder. The catalog's 16 in mid-length barrels have it at 8.85 to 8.87."},"gas_port_x":{"label":"The gas port ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":9.168,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-145-chf-barrel dc38f9181866 (Primary Arms' gallery, 05-2985_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its end faces, 1992.0 px apart (columns 103.5 and 2095.5, each behind its rim's arc: outline_front_face and outline_rear_face, tools/trace.py's fit), as overall_length (15.001): 132.79 px/in","method":"the flange's rear face (column 1962.5) to the dimple's centre: seen at column 740.7, row 759 (33 px under the axis: 42° round from the lens), which on the journal's near side is 4.3 px toward the muzzle of its station (the lens stands 6.5° toward the breech from there): column 745.0","via":"harvest"}},{"id":"rendering","value":9.16,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-145-chf-barrel 701c31f17604 (Rooftop Defense's picture, Geissele-14.5.jpg: a rendering of the barrel from above, the extension at the left, the index pin, the port and the G toward the viewer, 1080 x 1080)","scaleRef":"its own length, 1010 px between its ends as overall_length (15.001): 67 px/in","method":"the port's own centre, 18.8 px (0.28 in) ahead of the collar's front face, added to journal_rear_x (8.882)","via":"harvest"},"note":"The port itself, on a picture of a third of the photo's resolution: it is where the dimple is, within what either reads."}],"adopt":{"from":"photo","reason":"The photograph of the barrel, at twice the rendering's resolution; the rendering puts the port itself within 0.01 in of the dimple's station."},"note":"Read at the dimple under the journal, which is what Primary Arms' side photo shows (the barrel lies with its underside toward the lens: a spot-drilled hole 0.16 in across with a coned floor (dimple_d), twice the published .076 port; Mile High: \"There is one dimple machined in for a gas block set screw\"; a buyer on Primary Arms' page: \"it also has an indexing notch on the top and a dimple to help locate a gas block\"). The port is on top, opposite: Primary Arms' three-quarter photo (7f3cd09611e9) and Rooftop's picture (701c31f17604) show it small, just ahead of the collar, in line with the collar's notch and the index pin. That the port is at the dimple's station is taken, not read on this photo: a gas block's set screw is under its gas hole. Two pictures have the port itself there: Rooftop's rendering of this number (the second reading below), and Primary Arms' photo of the 13.9 in barrel, which lies port upward (0.29 in ahead of its collar: geissele-139-chf-barrel.gas_port_x). Checks: the port is 0.29 ahead of the journal's rear shoulder (BCM's 0.28, a mid-length chart's .300); Aero's mid-length port is at 9.17, BCM's 9.13, Bear Creek's 9.14, the chart's 9.18: mid-length by the photo as by the sellers' word."},"journal_front_x":{"label":"The gas block journal's front end (where the barrel begins to narrow) ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":9.93,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-145-chf-barrel dc38f9181866 (Primary Arms' gallery, 05-2985_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its end faces, 1992.0 px apart (columns 103.5 and 2095.5, each behind its rim's arc: outline_front_face and outline_rear_face, tools/trace.py's fit), as overall_length (15.001): 132.79 px/in","method":"the flange's rear face (column 1962.5) to where a line through the journal's radius (columns 650 to 770) meets a line through the cone's ahead of it (columns 570 to 640): column 643.9","via":"harvest"}}],"note":"The journal is 1.05 long. Ahead of it the barrel narrows to the muzzle section over 0.62 in, a cone (no step)."},"muzzle_run_rear_x":{"label":"Where the cone ahead of the journal ends and the muzzle section begins, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":10.545,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-145-chf-barrel dc38f9181866 (Primary Arms' gallery, 05-2985_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its end faces, 1992.0 px apart (columns 103.5 and 2095.5, each behind its rim's arc: outline_front_face and outline_rear_face, tools/trace.py's fit), as overall_length (15.001): 132.79 px/in","method":"the flange's rear face (column 1962.5) to where a line through the cone's radius (columns 570 to 640) meets a line through the muzzle section's (columns 240 to 460): column 562.2","via":"harvest"}}]},"muzzle_run_od":{"label":"The muzzle section's diameter, between the cone ahead of the journal and the ring behind the shoulder","kind":"length","measurements":[{"id":"photo","value":0.666,"unit":"in","pm":0.007,"source":{"type":"photo","photo":"references/geissele-145-chf-barrel dc38f9181866 (Primary Arms' gallery, 05-2985_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its gas block journal's diameter as the published .750 (the silhouette at grey 235: 50.16 px of radius over columns 655 to 770)","method":"columns 240 to 460: 44.54 px of radius against the journal's 50.16","via":"harvest"}}],"note":"A cylinder 2.5 in long (it changes by 0.14 px of radius along its length)."},"muzzle_ring_rear_x":{"label":"The rear end of the ring behind the muzzle shoulder, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":13.141,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-145-chf-barrel dc38f9181866 (Primary Arms' gallery, 05-2985_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its end faces, 1992.0 px apart (columns 103.5 and 2095.5, each behind its rim's arc: outline_front_face and outline_rear_face, tools/trace.py's fit), as overall_length (15.001): 132.79 px/in","method":"the flange's rear face (column 1962.5) to the last column at the ring's full radius (217: 46.7 px; 46.6 at 218 and falling to 44.6 at 229)","via":"harvest"}}],"note":"The ring is 0.24 long at its full diameter and comes down to the muzzle section over another 0.1 in (columns 218 to 232), a chamfer and not a step."},"muzzle_ring_foot_x":{"label":"Where the ring's rear chamfer meets the muzzle section, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":13.04,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-145-chf-barrel dc38f9181866 (Primary Arms' gallery, 05-2985_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its end faces, 1992.0 px apart (columns 103.5 and 2095.5, each behind its rim's arc: outline_front_face and outline_rear_face, tools/trace.py's fit), as overall_length (15.001): 132.79 px/in","method":"the flange's rear face (column 1962.5) to the first column at the muzzle section's radius behind the ring (231: 44.6 px, as at 235)","via":"harvest"}}]},"shoulder_x":{"label":"The muzzle shoulder ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":13.381,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-145-chf-barrel dc38f9181866 (Primary Arms' gallery, 05-2985_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its end faces, 1992.0 px apart (columns 103.5 and 2095.5, each behind its rim's arc: outline_front_face and outline_rear_face, tools/trace.py's fit), as overall_length (15.001): 132.79 px/in","method":"the flange's rear face (column 1962.5) to the shoulder's face (column 185.7: the silhouette's step is at 180.5 at half height, 5 px toward the muzzle by the ring's rim's arc, the lens being 13° toward the breech from there; columns 181 to 184 each put the face at 185.4 to 185.9)","via":"harvest"}}],"note":"Where the thread begins: a muzzle device or its washer seats here, on the ring's front face."},"thread_length":{"label":"The muzzle thread's length","kind":"length","measurements":[{"id":"photo","value":0.619,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-145-chf-barrel dc38f9181866 (Primary Arms' gallery, 05-2985_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its end faces, 1992.0 px apart (columns 103.5 and 2095.5, each behind its rim's arc: outline_front_face and outline_rear_face, tools/trace.py's fit), as overall_length (15.001): 132.79 px/in","method":"the shoulder's face (column 185.7) to the muzzle's face (column 103.5, behind its rim's 7 px arc)","via":"harvest"}}],"note":"The Army's barrel has .63 here (8448549 sheet 1, from the shoulder to the muzzle); a mid-length chart .624."},"muzzle_od":{"label":"The diameter behind the muzzle thread","kind":"length","measurements":[{"id":"photo","value":0.699,"unit":"in","pm":0.007,"source":{"type":"photo","photo":"references/geissele-145-chf-barrel dc38f9181866 (Primary Arms' gallery, 05-2985_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its gas block journal's diameter as the published .750 (the silhouette at grey 235: 50.16 px of radius over columns 655 to 770)","method":"columns 190 to 214: 46.73 px of radius against the journal's 50.16 (0.6986)","via":"harvest"}}],"note":"The ring behind the shoulder, a quarter of an inch long; the muzzle section behind it is 0.666 (muzzle_run_od). Rooftop's picture of the barrel (701c31f17604) shows the same ring, with Geissele's G just behind it."},"bore_d":{"label":"The bore's diameter (across the lands)","kind":"length","measurements":[{"id":"tdp","value":0.219,"unit":"in","pm":0.001,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.bore_d}","via":"user"},"note":"The Army's barrel drawing (8448549 sheet 2, Section U-U: \".219 DIA+.001\"), as read for BCM's barrel's ledger, where the drawing and its page are cited."}],"note":"The cartridge's, for the hole the model cuts: the sellers state \"Chambered in 5.56 NATO\" and no bore."},"index_pin_d":{"label":"The barrel indexing pin's diameter","kind":"length","measurements":[{"id":"tdp","value":0.12525,"unit":"in","pm":0.00025,"source":{"type":"derived","expr":"{bca-556-16-mid-barrel.index_pin_d}","via":"user"},"note":"The Army's own part (8448551, Pin, Barrel Indexing: \".1255 DIA -.0005\"), as read for Bear Creek's barrel's ledger, where the drawing and its page are cited."}]},"index_pin_protrusion":{"label":"The barrel indexing pin's top above the extension's surface","kind":"length","measurements":[{"id":"tdp","value":0.094,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{bca-556-16-mid-barrel.index_pin_protrusion}","via":"user"},"note":"The Army's assembly drawing (8448548, Section A-A: \".094 MAX\"), as read for Bear Creek's barrel's ledger, where the drawing and its page are cited."}],"note":"A limit, and the model draws the pin at it. No photo of this barrel has the pin on its silhouette."},"index_pin_x":{"label":"The barrel indexing pin's axis behind the flange's rear face","kind":"length","measurements":[{"id":"photo","value":0.063,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/geissele-145-chf-barrel 701c31f17604 (Rooftop Defense's picture, Geissele-14.5.jpg: a rendering of the barrel from above, the extension at the left, the index pin, the port and the G toward the viewer, 1080 x 1080)","scaleRef":"its own length, 1010 px between its ends as overall_length (15.001): 67 px/in","method":"the pin's round outline, 8 px across, touches the flange's rear face: its axis half its diameter (index_pin_d) behind the face. Primary Arms' photos have the pin on the far side","via":"harvest"}}],"note":"The pin stands against the flange, in line with the gas port and the collar's notch."},"extension_mouth_d":{"label":"The barrel extension's rear opening, its diameter at the rear face","kind":"length","measurements":[{"id":"model","value":0.77,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_mouth_d}","via":"user"}}],"note":"The inside of a mil-spec M4 extension as the reference CAD set has it, for how the rear end looks (the sellers: \"BARREL EXTENSION: M4 Feedramps\"; two sellers' photos of this barrel's breech, ba2bd32ed9c1 and 5acd733fbeb8, show the lugs and the ramps). Appearance only; the six figures of the opening are the readings made for BCM's barrel's ledger, where the file and the method are cited."},"extension_mouth_chamfer":{"label":"The rear opening's chamfer, its depth (at 45°, also how far it narrows the opening's radius)","kind":"length","measurements":[{"id":"model","value":0.045,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_mouth_chamfer}","via":"user"}}]},"extension_lug_bore_d":{"label":"The circle the extension's locking lugs leave between their tips","kind":"length","measurements":[{"id":"model","value":0.572,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_lug_bore_d}","via":"user"}}]},"extension_lug_depth":{"label":"The locking lugs' front faces, ahead of the extension's rear end","kind":"length","measurements":[{"id":"model","value":0.214,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_lug_depth}","via":"user"}}]},"extension_recess_d":{"label":"The recess ahead of the lugs, which the bolt's lugs turn in: its diameter","kind":"length","measurements":[{"id":"model","value":0.83,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_recess_d}","via":"user"}}]},"extension_recess_depth":{"label":"The recess's front end, ahead of the extension's rear end","kind":"length","measurements":[{"id":"model","value":0.595,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_recess_depth}","via":"user"}}]},"thread_major_d":{"label":"The muzzle thread's major diameter (its crests)","kind":"length","measurements":[{"id":"tdp","value":0.4957,"unit":"in","pm":0.0033,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.thread_major_d}","via":"user"},"note":"8448549 sheet 1, Section M-M: \"1/2-28 UNEF-2A MAJOR DIA .4989/.4924\", as read for BCM's barrel's ledger."}],"note":"The Army barrel's 1/2-28 thread, for the 1/2 x 28 the sellers state: what the model's thread is drawn at. The photo's silhouette of the thread is 0.489 (its median) to 0.494 (tools/turned.py) at the journal's scale."},"thread_minor_d":{"label":"The muzzle thread's minor diameter (its roots)","kind":"length","measurements":[{"id":"tdp","value":0.4551,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.thread_minor_d}","via":"user"},"note":"8448549 sheet 1, Section M-M: \"MINOR DIA .4551 MAX\", as read for BCM's barrel's ledger."}]},"thread_pitch":{"label":"The muzzle thread's pitch","kind":"length","measurements":[{"id":"primary-arms","value":0.03571,"unit":"in","pm":0.00005,"stated":"Thread Pattern 1/2 X 28","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics CHF Chrome Lined 5.56 AR-15 Barrel - Mid-Length - Tapered - 14.5\" (05-2985), Specifications; its Features: \"Threaded 1/2x28\"","url":"https://www.primaryarms.com/geissele-automatics-5-56-chf-mid-length-taper-profile-ar-15-barrel-chrome-lined-14-5in","retrieved":"2026-10-06","via":"harvest"}},{"id":"mile-high","value":0.03571,"unit":"in","pm":0.00005,"stated":"MUZZLE THREAD: 1/2 x 28","source":{"type":"spec","publisher":"retailer","name":"Mile High Shooting Accessories, Geissele: CHF, Chrome Lined Barrel, 5.56 - 14.5\" (SKU 05-2985), Specifications","url":"https://www.milehighshooting.com/geissele-chf-chrome-lined-barrel-5-56-14-5/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"primary-arms","reason":"Two sellers' pages state the one thread."},"note":"28 threads to the inch, by the sellers' statement: not a measurement of this barrel."},"dimple_d":{"label":"The dimple under the journal, for a gas block's set screw: its diameter at the journal's surface","kind":"length","measurements":[{"id":"photo","value":0.156,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/geissele-145-chf-barrel 436ef5001d7d (Primary Arms' gallery, 05-2985_03: the journal close up, level, the dimple toward the lens, 2200 x 1467)","scaleRef":"the journal's diameter there, 365 px (columns 760 to 1180, the silhouette at grey 235), as the published .750 (journal_od): 486.7 px/in","method":"a circle through the dimple's rim (the strongest edges round it): 37.9 px of radius, rms 2.2 px, its centre 11 px off the journal's middle row (.cache/batch46/geissele-145-chf-barrel/closeup.py)","via":"harvest"}}],"note":"Mile High: \"There is one dimple machined in for a gas block set screw\". A drilled spot with a coned floor. Not drawn: its depth isn't sourced (dimple_depth)."},"dimple_depth":{"label":"The dimple under the journal: its depth","kind":"length","measurements":[],"note":"No source: the one close photo looks straight into it. Not drawn until a figure or a view with its edge on the silhouette is on file."},"collar_slot_w":{"label":"The slot along the collar's top, in line with the gas port: its width","kind":"length","measurements":[],"note":"A buyer on Primary Arms' page: \"it also has an indexing notch on the top and a dimple to help locate a gas block\". On the far side in the side photo; a mark a few pixels across in the three-quarter view (7f3cd09611e9) and on Rooftop's rendering. Not read, and not drawn. (The 13.9 in barrel's own photo shows its slot from above.)"},"outline_rear_face":{"label":"The extension's rear face in the traced outline's own frame (from the silhouette's rear tip, at the journal's scale)","kind":"length","measurements":[{"id":"photo","value":0.069,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/geissele-145-chf-barrel dc38f9181866 (Primary Arms' gallery, 05-2985_02: the barrel level on white, the muzzle at the left, 2200 x 1467)","scaleRef":"scale from geissele-145-chf-barrel.flange_od = 1.168 in (y-extent 156 px → 133.6 px/in)","method":"the min end's face: the silhouette's tip at 0.002 less its rim's arc, 0.067 in of sag at radius 0.497179 (the end is seen from 7.6° off square; arc fitted over 100 rows, rms 0.004) of the traced outline (tools/trace.py); the extension's rear face in the outline's own frame (from its rear tip, at the journal's scale)","via":"harvest"}}],"note":"Where the outline is cut: the silhouette's tip is the rear rim's near side, which stands behind the face by the rim's arc."},"outline_front_face":{"label":"The muzzle's face in the traced outline's own frame (from the silhouette's rear tip, at the journal's scale)","kind":"length","measurements":[{"id":"photo","value":14.979,"unit":"in","pm":0.091,"source":{"type":"photo","photo":"references/geissele-145-chf-barrel dc38f9181866 (Primary Arms' gallery, 05-2985_02: the barrel level on white, the muzzle at the left, 2200 x 1467)","scaleRef":"scale from geissele-145-chf-barrel.flange_od = 1.168 in (y-extent 156 px → 133.6 px/in)","method":"the max end's face: the silhouette's tip at 15.031 less its rim's arc, 0.052 in of sag at radius 0.240181 (the end is seen from 12.2° off square; arc fitted over 113 rows, rms 0.002) of the traced outline (tools/trace.py); the muzzle's face in the outline's own frame (from its rear tip, at the journal's scale)","via":"harvest"}}],"note":"Where the outline is cut: the silhouette's front tip is the muzzle rim's near side."}}},{"subject":"geissele-16-chf-barrel","title":"Geissele Automatics CHF Chrome Lined Barrel - 5.56 - 16\" (05-2984)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"primary-arms","value":1.7,"unit":"lb","pm":0.05,"stated":"Weight 1.7 lbs","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics CHF Chrome Lined 5.56 AR-15 Barrel - Mid-Length - Tapered - 16\" (05-2984), Specifications; its Features: \"1.7 lbs weight\"","url":"https://www.primaryarms.com/geissele-automatics-5-56-chf-chrome-lined-ar-15-barrel-mid-length-taper-profile-16in","retrieved":"2026-10-28","via":"harvest"}},{"id":"ar15discounts","value":27.2,"unit":"oz","pm":0.05,"stated":"Weight 27.2 oz","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, Geissele Automatics 16.25\" CHF Government Phosphate 1:7 Midlengtrh Barrel - 05-2984 (its own SKU 13291; MPN 05-2984, UPC 810081134903), Additional information; its Specifications: \"Weight: 1.7 lbs\"","url":"https://ar15discounts.com/products/geissele-automatics-16-chf-government-phosphate-17-midlengtrh-barrel/","retrieved":"2026-10-28","via":"harvest"}}],"adopt":{"from":"primary-arms","reason":"Two sellers' pages state the one figure (27.2 oz is 1.7 lb); Primary Arms' is the page whose photo the barrel is drawn from. Geissele's own page isn't read."},"note":"Two sellers' pages, one figure (27.2 oz is 1.7 lb), none the maker's own. Blackstone Shooting's \"Geissele Automatics 05-1860, 5.56 NATO, 16.00\\\" Barrel, Chrome Lined\" (UPC 810081130868) is another number, not a reading of this one. The model's volume as steel is the check (app/tests/geissele-16-chf-barrel.test.ts)."},"journal_od":{"label":"The gas block journal's diameter","kind":"length","measurements":[{"id":"primary-arms","value":0.75,"unit":"in","pm":0.0005,"stated":"Gas Seat Diameter .750","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics CHF Chrome Lined 5.56 AR-15 Barrel - Mid-Length - Tapered - 16\" (05-2984), Specifications","url":"https://www.primaryarms.com/geissele-automatics-5-56-chf-chrome-lined-ar-15-barrel-mid-length-taper-profile-16in","retrieved":"2026-10-28","via":"harvest"}},{"id":"ar15discounts","value":0.75,"unit":"in","pm":0.0005,"stated":"Gas Block Diameter: .750","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, Geissele Automatics 16.25\" CHF Government Phosphate 1:7 Midlengtrh Barrel - 05-2984, Specifications; its Additional information: \"Gas Block Journal 0.75\"","url":"https://ar15discounts.com/products/geissele-automatics-16-chf-government-phosphate-17-midlengtrh-barrel/","retrieved":"2026-10-28","via":"harvest"}}],"adopt":{"from":"primary-arms","reason":"Two sellers' pages state the one diameter; none is the maker's own page."}},"gas_port_d":{"label":"The gas port's diameter","kind":"length","measurements":[{"id":"ar15discounts","value":0.078,"unit":"in","pm":0.0005,"stated":"Gas Port: .078","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, Geissele Automatics 16.25\" CHF Government Phosphate 1:7 Midlengtrh Barrel - 05-2984, Specifications","url":"https://ar15discounts.com/products/geissele-automatics-16-chf-government-phosphate-17-midlengtrh-barrel/","retrieved":"2026-10-28","via":"harvest"}}],"note":"One seller's page (provisional). The 14.5 in sibling's sellers print .076 and the 13.9 in's .081: each barrel its own."},"extension_behind_breech":{"label":"The barrel extension's rear end behind the barrel's breech end","kind":"length","measurements":[{"id":"model","value":0.501,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{std.ar15.barrel_extension_behind_breech}","via":"user"}}],"note":"The standard's (the reference CAD set's extension less the Army's .620 tenon: std.ar15.barrel_extension_length, std.ar15.barrel_tenon_length), as the catalog's other 5.56 barrels take it: the sellers state an M4 extension (Primary Arms: \"Feed Ramps M4\"; AR15Discounts: \"Barrel Extension: M4 Feedramps\") and nothing of its size."},"extension_od":{"label":"The barrel extension's body, its diameter (what goes into the receiver)","kind":"length","measurements":[{"id":"tdp","value":0.999,"unit":"in","pm":0.001,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_od}","via":"user"},"note":"The Army's limit on the assembly drawing (8448548: \"DIAMETER NOT TO EXCEED .9990 FOR THIS LENGTH AFTER ASSEMBLY AND BEFORE FINISH\"), as read for BCM's barrel's ledger, where the drawing and its page are cited."}],"note":"Not read off this photo: with the journal it is what the photo's scale is taken from (at the journal's scale alone it reads .974, which is how the photo's yaw shows: outline_extension_od)."},"bore_d":{"label":"The bore's diameter (across the lands)","kind":"length","measurements":[{"id":"tdp","value":0.219,"unit":"in","pm":0.001,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.bore_d}","via":"user"},"note":"The Army's barrel drawing (8448549 sheet 2, Section U-U: \".219 DIA+.001\"), as read for BCM's barrel's ledger, where the drawing and its page are cited."}],"note":"The cartridge's, for the hole the model cuts: the sellers state \"Chambered in 5.56 NATO\" and no bore."},"index_pin_d":{"label":"The barrel indexing pin's diameter","kind":"length","measurements":[{"id":"tdp","value":0.12525,"unit":"in","pm":0.00025,"source":{"type":"derived","expr":"{bca-556-16-mid-barrel.index_pin_d}","via":"user"},"note":"The Army's own part (8448551, Pin, Barrel Indexing: \".1255 DIA -.0005\"), as read for Bear Creek's barrel's ledger, where the drawing and its page are cited."}]},"index_pin_protrusion":{"label":"The barrel indexing pin's top above the extension's surface","kind":"length","measurements":[{"id":"tdp","value":0.094,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{bca-556-16-mid-barrel.index_pin_protrusion}","via":"user"},"note":"The Army's assembly drawing (8448548, Section A-A: \".094 MAX\"), as read for Bear Creek's barrel's ledger, where the drawing and its page are cited."}],"note":"A limit, and the model draws the pin at it. In Primary Arms' side photo the pin is on the far side (the photo shows the journal's underside): it isn't on the silhouette."},"index_pin_x":{"label":"The barrel indexing pin's axis behind the flange's rear face","kind":"length","measurements":[{"id":"drawing","value":0.0626,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{.index_pin_d} / 2","via":"user"}}],"note":"The pin standing against the flange, as the Army's Section A-A draws it (Bear Creek's barrel's ledger, where the drawing is cited): its axis half its diameter behind the face. AR15Discounts' picture of this number from above (d8cb93933e36, a grey rendering, 700 px, about 38 px to the inch) has the pin's round top just behind the flange, in line with the gas port: too small a picture to read the station on."},"extension_mouth_d":{"label":"The barrel extension's rear opening, its diameter at the rear face","kind":"length","measurements":[{"id":"model","value":0.77,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_mouth_d}","via":"user"}}],"note":"The inside of a mil-spec M4 extension as the reference CAD set has it, for how the rear end looks (the sellers: \"Feed Ramps M4\", \"Barrel Extension: M4 Feedramps\"; AR15Discounts' pictures of this number's breech, 8c26bfec846f and cb50ea82427d, show the lugs and the ramps). Appearance only; the six figures of the opening are the readings made for BCM's barrel's ledger, where the file and the method are cited."},"extension_mouth_chamfer":{"label":"The rear opening's chamfer, its depth (at 45°, also how far it narrows the opening's radius)","kind":"length","measurements":[{"id":"model","value":0.045,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_mouth_chamfer}","via":"user"}}]},"extension_lug_bore_d":{"label":"The circle the extension's locking lugs leave between their tips","kind":"length","measurements":[{"id":"model","value":0.572,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_lug_bore_d}","via":"user"}}]},"extension_lug_depth":{"label":"The locking lugs' front faces, ahead of the extension's rear end","kind":"length","measurements":[{"id":"model","value":0.214,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_lug_depth}","via":"user"}}]},"extension_recess_d":{"label":"The recess ahead of the lugs, which the bolt's lugs turn in: its diameter","kind":"length","measurements":[{"id":"model","value":0.83,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_recess_d}","via":"user"}}]},"extension_recess_depth":{"label":"The recess's front end, ahead of the extension's rear end","kind":"length","measurements":[{"id":"model","value":0.595,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_recess_depth}","via":"user"}}]},"thread_major_d":{"label":"The muzzle thread's major diameter (its crests)","kind":"length","measurements":[{"id":"tdp","value":0.4957,"unit":"in","pm":0.0033,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.thread_major_d}","via":"user"},"note":"8448549 sheet 1, Section M-M: \"1/2-28 UNEF-2A MAJOR DIA .4989/.4924\", as read for BCM's barrel's ledger."}],"note":"The Army barrel's 1/2-28 thread, for the 1/2 x 28 the sellers state: what the model's thread is drawn at. The photo's silhouette of the thread is .494 through its distortion (59.86 px over columns 110 to 160)."},"thread_minor_d":{"label":"The muzzle thread's minor diameter (its roots)","kind":"length","measurements":[{"id":"tdp","value":0.4551,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.thread_minor_d}","via":"user"},"note":"8448549 sheet 1, Section M-M: \"MINOR DIA .4551 MAX\", as read for BCM's barrel's ledger."}]},"thread_pitch":{"label":"The muzzle thread's pitch","kind":"length","measurements":[{"id":"photo","value":0.03573,"unit":"in","pm":0.0004,"source":{"type":"photo","photo":"references/geissele-16-chf-barrel 3ab505012996 (Primary Arms' gallery, 05-2984_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"the scale along the barrel at the thread (column 135), through the radial distortion its journal and its extension fix: 118.95 px/in","method":"the thread's face toward the lens, rows 720 to 740 over columns 104 to 165: a Fourier fit of the grey along it, 4.25 px a pitch (± 0.05); the edges' rows give 4.21 and 4.26","via":"harvest"},"note":"The check of the photo's distortion, not a reading the model uses: at the journal's scale alone it would be 0.0347."},{"id":"primary-arms","value":0.03571,"unit":"in","pm":0.00005,"stated":"Thread Pattern 1/2 X 28","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics CHF Chrome Lined 5.56 AR-15 Barrel - Mid-Length - Tapered - 16\" (05-2984), Specifications; its Features: \"Threaded 1/2x28\"","url":"https://www.primaryarms.com/geissele-automatics-5-56-chf-chrome-lined-ar-15-barrel-mid-length-taper-profile-16in","retrieved":"2026-10-28","via":"harvest"}},{"id":"ar15discounts","value":0.03571,"unit":"in","pm":0.00005,"stated":"Muzzle Thread: 1/2 x 28","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, Geissele Automatics 16.25\" CHF Government Phosphate 1:7 Midlengtrh Barrel - 05-2984, Specifications; its Additional information: \"Muzzle Thread Pattern 1/2×28\"","url":"https://ar15discounts.com/products/geissele-automatics-16-chf-government-phosphate-17-midlengtrh-barrel/","retrieved":"2026-10-28","via":"harvest"}}],"adopt":{"from":"primary-arms","reason":"Two sellers' pages state the one thread; the photo's pitch agrees through the distortion its journal and extension fix."},"note":"28 threads to the inch, by the sellers' statement: not a measurement of this barrel."},"length":{"label":"Barrel length as its sellers state it for the maker","kind":"length","measurements":[{"id":"primary-arms","value":16,"unit":"in","pm":0.05,"stated":"Barrel Length 16","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics CHF Chrome Lined 5.56 AR-15 Barrel - Mid-Length - Tapered - 16\" (05-2984), Specifications; its Features: \"16\\\" cold hammer-forged barrel\"","url":"https://www.primaryarms.com/geissele-automatics-5-56-chf-chrome-lined-ar-15-barrel-mid-length-taper-profile-16in","retrieved":"2026-10-28","via":"harvest"}},{"id":"ar15discounts","value":16.25,"unit":"in","pm":0.005,"stated":"Length: 16.25″","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, Geissele Automatics 16.25\" CHF Government Phosphate 1:7 Midlengtrh Barrel - 05-2984 (MPN 05-2984, UPC 810081134903), Specifications; the same page's Additional information has \"Barrel Length 16\\\"\"","url":"https://ar15discounts.com/products/geissele-automatics-16-chf-government-phosphate-17-midlengtrh-barrel/","retrieved":"2026-10-28","via":"harvest"}}],"adopt":{"from":"primary-arms","reason":"The figure two pages state (Primary Arms' table, features and title; AR15Discounts' own Barrel Length field), against one list on one page. The photo reads between the two and can't choose (see the note). Both make the barrel 16 in or more: a rifle's, under the Act, either way."},"note":"The nominal length: what the site's federal-law line goes by (D80). Stated two ways. Primary Arms' table and features, its title and its picture's alt text say 16; AR15Discounts says 16.25 in its title and in its Specifications list (the list in the maker's table's words: \"Length:\", \"Rifling:\", \"Gas Port:\", \"Barrel Extension:\", as Mile High copies them for the 14.5 in barrel) and 16 in its own filter field (\"Barrel Length 16\\\"\"). No page says between which points; the Army's barrel drawing (8448549) dimensions a barrel from its breech end, inside the extension, and overall_length takes it so. The photo doesn't decide: through the lens distortion its journal and its extension fix (and its thread's pitch checks), its end faces are 16.614 in apart, 0.7% over 16.501 and 0.8% under 16.751 (the 14.5 in and 13.9 in barrels' photos read 0.6% and 1.2% under theirs), and its gas block's dimple lands at 9.08 ahead of the receiver's face at 16 and 9.22 at 16.25, either side of the mid-length ports on file (9.13 to 9.17). Either is 16 in or more."},"overall_length":{"label":"End to end, the extension's rear to the muzzle","kind":"length","measurements":[{"id":"photo","value":16.614,"unit":"in","pm":0.12,"source":{"type":"photo","photo":"references/geissele-16-chf-barrel 3ab505012996 (Primary Arms' gallery, 05-2984_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its gas block journal as the published .750 (45.874 px of radius over columns 805 to 905, the silhouette at grey 235: 122.33 px/in) and its extension's body as the Army's .999 (59.543 px over columns 1990 to 2080), through a radial lens distortion about the journal's middle (column 855) that those two fix: k = -1.743e-8 per px², the scale across the barrel 1 + k r², along it 1 + 3 k r², r the distance from column 855 undistorted","method":"its two end faces, each behind its rim's arc (tools/trace.py's `ends`: the extension's rear at column 2088.9, its arc 0.119 in at 13.9° off square; the muzzle's at 99.9, 0.096 in at 21.8°), undistorted. Check: the thread's crests, 28 to the inch by the sellers, read 4.25 px a pitch over 62 columns (a Fourier fit of the thread's face, rows 720 to 740), where the model has 4.248 (.cache/batch15/geissele-16-chf-barrel/stations.py)","via":"harvest"}},{"id":"published","value":16.501,"unit":"in","pm":0.07,"source":{"type":"derived","expr":"{.length} + {.extension_behind_breech}","via":"harvest"}}],"adopt":{"from":"published","reason":"Lengths at the published length's scale, as the catalog's other barrels: the photo is within its ± of it."},"note":"The photo, through the radial distortion its journal (.750, published) and its extension (.999, the Army's limit) fix about the journal's middle, has its two end faces 16.614 apart: 0.7% over the published length's 16.501 (and 0.8% under the 16.751 AR15Discounts' 16.25 would make it). At the journal's scale alone they are 16.259 apart, and the thread's 28 to the inch reads 2.7% off there; a straight yaw between the journal and the extension (the 13.9 in barrel's correction, which has both of those right) leaves it 4.4% off the other way, and puts the thread's crests at .482, under the Army's .4924. Through the distortion the crests' silhouette is .494 and the pitch within 0.05%. The published length is the scale for lengths, as the catalog's other barrels'."},"extension_rear_x":{"label":"The barrel extension's rear end, from the flange's rear face (negative: inside the receiver)","kind":"length","measurements":[{"id":"photo","value":-1,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-16-chf-barrel 3ab505012996 (Primary Arms' gallery, 05-2984_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its end faces (columns 2088.9 and 99.9, each behind its rim's arc: outline_rear_face and outline_front_face, tools/trace.py), 16.614 in apart through the same distortion (its scale along the barrel falls three times as fast as across it, and the thread's 28 to the inch read 4.25 px a pitch where it gives 4.248), stretched by 0.99322 to overall_length (16.501)","method":"the rear end's face (column 2088.9, behind its rim's 17 px arc) to the flange's rear face (column 1975.0: the silhouette's step between the flange's rim and the extension's body at 0.93 of the flange's radius, column 1980.3, less its rear rim's ellipse there, the face seen from 12° off square)","via":"harvest"}}]},"flange_front_x":{"label":"The extension flange's front face, ahead of its rear face (the flange's thickness)","kind":"length","measurements":[{"id":"photo","value":0.155,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/geissele-16-chf-barrel 3ab505012996 (Primary Arms' gallery, 05-2984_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its end faces (columns 2088.9 and 99.9, each behind its rim's arc: outline_rear_face and outline_front_face, tools/trace.py), 16.614 in apart through the same distortion (its scale along the barrel falls three times as fast as across it, and the thread's 28 to the inch read 4.25 px a pitch where it gives 4.248), stretched by 0.99322 to overall_length (16.501)","method":"the flange's rear face (column 1975.0) to its front face (column 1957.2: the step at 0.93 of its radius, column 1952.0, and its front rim's ellipse). The blur of a 122 px/in photo widens both corners: the reference CAD set's flange is 0.131 thick","via":"harvest"}}]},"flange_od":{"label":"The barrel extension's flange, its diameter","kind":"length","measurements":[{"id":"photo","value":1.166,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/geissele-16-chf-barrel 3ab505012996 (Primary Arms' gallery, 05-2984_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its gas block journal as the published .750 (45.874 px of radius over columns 805 to 905, the silhouette at grey 235: 122.33 px/in) and its extension's body as the Army's .999 (59.543 px over columns 1990 to 2080), through a radial lens distortion about the journal's middle (column 855) that those two fix (the extension's diameter 2.6% small, 1180 px off); the scale across the barrel at this station","method":"the silhouette's widest, columns 1962 to 1970: 69.73 px of radius","via":"harvest"}}]},"chamber_od":{"label":"The chamber section's diameter, ahead of the flange","kind":"length","measurements":[{"id":"photo","value":0.982,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/geissele-16-chf-barrel 3ab505012996 (Primary Arms' gallery, 05-2984_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its gas block journal as the published .750 (45.874 px of radius over columns 805 to 905, the silhouette at grey 235: 122.33 px/in) and its extension's body as the Army's .999 (59.543 px over columns 1990 to 2080), through a radial lens distortion about the journal's middle (column 855) that those two fix (the extension's diameter 2.6% small, 1180 px off); the scale across the barrel at this station","method":"columns 1870 to 1945: 58.85 px of radius","via":"harvest"}}]},"chamber_front_x":{"label":"Where the chamber section ends and the barrel begins to narrow, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":0.937,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-16-chf-barrel 3ab505012996 (Primary Arms' gallery, 05-2984_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its end faces (columns 2088.9 and 99.9, each behind its rim's arc: outline_rear_face and outline_front_face, tools/trace.py), 16.614 in apart through the same distortion (its scale along the barrel falls three times as fast as across it, and the thread's 28 to the inch read 4.25 px a pitch where it gives 4.248), stretched by 0.99322 to overall_length (16.501)","method":"the flange's rear face (column 1975.0) to where a line through the chamber section's radius (columns 1870 to 1945) meets a line through the cone's (columns 1725 to 1850)","via":"harvest"}}]},"taper_rear_x":{"label":"Where the cone ahead of the chamber ends and the long taper begins, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":2.32,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-16-chf-barrel 3ab505012996 (Primary Arms' gallery, 05-2984_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its end faces (columns 2088.9 and 99.9, each behind its rim's arc: outline_rear_face and outline_front_face, tools/trace.py), 16.614 in apart through the same distortion (its scale along the barrel falls three times as fast as across it, and the thread's 28 to the inch read 4.25 px a pitch where it gives 4.248), stretched by 0.99322 to overall_length (16.501)","method":"the flange's rear face (column 1975.0) to where a line through the cone's radius (columns 1725 to 1850) meets a line through the long taper's (columns 1050 to 1650)","via":"harvest"}}]},"taper_rear_od":{"label":"The long taper's diameter at its rear end (the Geissele Taper Profile's thick end)","kind":"length","measurements":[{"id":"photo","value":0.728,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/geissele-16-chf-barrel 3ab505012996 (Primary Arms' gallery, 05-2984_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its gas block journal as the published .750 (45.874 px of radius over columns 805 to 905, the silhouette at grey 235: 122.33 px/in) and its extension's body as the Army's .999 (59.543 px over columns 1990 to 2080), through a radial lens distortion about the journal's middle (column 855) that those two fix (the extension's diameter 2.6% small, 1180 px off); the scale across the barrel at this station","method":"the two lines' crossing (column 1704): 43.42 px of radius","via":"harvest"}}]},"taper_front_x":{"label":"Where the long taper ends and the barrel flares to the gas block's collar, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":8.21,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-16-chf-barrel 3ab505012996 (Primary Arms' gallery, 05-2984_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its end faces (columns 2088.9 and 99.9, each behind its rim's arc: outline_rear_face and outline_front_face, tools/trace.py), 16.614 in apart through the same distortion (its scale along the barrel falls three times as fast as across it, and the thread's 28 to the inch read 4.25 px a pitch where it gives 4.248), stretched by 0.99322 to overall_length (16.501)","method":"the flange's rear face (column 1975.0) to where a line through the long taper's radius (columns 1050 to 1650) meets a line through the flare's (columns 950 to 990): column 990","via":"harvest"}}]},"taper_front_od":{"label":"The long taper's diameter at its front end (the barrel's thinnest behind the gas block)","kind":"length","measurements":[{"id":"photo","value":0.665,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/geissele-16-chf-barrel 3ab505012996 (Primary Arms' gallery, 05-2984_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its gas block journal as the published .750 (45.874 px of radius over columns 805 to 905, the silhouette at grey 235: 122.33 px/in) and its extension's body as the Army's .999 (59.543 px over columns 1990 to 2080), through a radial lens distortion about the journal's middle (column 855) that those two fix (the extension's diameter 2.6% small, 1180 px off); the scale across the barrel at this station","method":"the two lines' crossing at column 990","via":"harvest"}}]},"collar_od":{"label":"The collar behind the gas block journal, its diameter","kind":"length","measurements":[{"id":"photo","value":0.842,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/geissele-16-chf-barrel 3ab505012996 (Primary Arms' gallery, 05-2984_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its gas block journal as the published .750 (45.874 px of radius over columns 805 to 905, the silhouette at grey 235: 122.33 px/in) and its extension's body as the Army's .999 (59.543 px over columns 1990 to 2080), through a radial lens distortion about the journal's middle (column 855) that those two fix (the extension's diameter 2.6% small, 1180 px off); the scale across the barrel at this station","method":"columns 921 to 930: 51.50 px of radius","via":"harvest"}}]},"collar_rear_x":{"label":"Where the collar's full diameter ends, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":8.678,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-16-chf-barrel 3ab505012996 (Primary Arms' gallery, 05-2984_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its end faces (columns 2088.9 and 99.9, each behind its rim's arc: outline_rear_face and outline_front_face, tools/trace.py), 16.614 in apart through the same distortion (its scale along the barrel falls three times as fast as across it, and the thread's 28 to the inch read 4.25 px a pitch where it gives 4.248), stretched by 0.99322 to overall_length (16.501)","method":"the flange's rear face (column 1975.0) to the last column within 0.15 px of the collar's full radius","via":"harvest"}}]},"journal_rear_x":{"label":"The gas block journal's rear shoulder (the collar's front face) ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":8.776,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-16-chf-barrel 3ab505012996 (Primary Arms' gallery, 05-2984_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its end faces (columns 2088.9 and 99.9, each behind its rim's arc: outline_rear_face and outline_front_face, tools/trace.py), 16.614 in apart through the same distortion (its scale along the barrel falls three times as fast as across it, and the thread's 28 to the inch read 4.25 px a pitch where it gives 4.248), stretched by 0.99322 to overall_length (16.501)","method":"the flange's rear face (column 1975.0) to the collar's front face (column 920.4: the silhouette's step at 0.95 of the way from the journal's radius to the collar's, column 918.6, less the face's rim's ellipse there, the face seen from 8° off square; columns 915 to 917 are the dark relief at the face's foot)","via":"harvest"}}]},"gas_port_x":{"label":"The gas port ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":9.079,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-16-chf-barrel 3ab505012996 (Primary Arms' gallery, 05-2984_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its end faces (columns 2088.9 and 99.9, each behind its rim's arc: outline_rear_face and outline_front_face, tools/trace.py), 16.614 in apart through the same distortion (its scale along the barrel falls three times as fast as across it, and the thread's 28 to the inch read 4.25 px a pitch where it gives 4.248), stretched by 0.99322 to overall_length (16.501)","method":"the flange's rear face (column 1975.0) to the dimple's centre: a circle through its rim on an eight-fold enlargement, columns 873.8 to 892.5 and rows 720 to 737 (2.5 px above the axis at row 731: it faces the lens), column 883.1","via":"harvest"}}]},"journal_front_x":{"label":"The gas block journal's front end (where the barrel begins to narrow) ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":9.793,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-16-chf-barrel 3ab505012996 (Primary Arms' gallery, 05-2984_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its end faces (columns 2088.9 and 99.9, each behind its rim's arc: outline_rear_face and outline_front_face, tools/trace.py), 16.614 in apart through the same distortion (its scale along the barrel falls three times as fast as across it, and the thread's 28 to the inch read 4.25 px a pitch where it gives 4.248), stretched by 0.99322 to overall_length (16.501)","method":"the flange's rear face (column 1975.0) to where a line through the journal's radius (columns 805 to 905) meets a line through the cone's ahead of it (columns 715 to 780)","via":"harvest"}}]},"muzzle_run_rear_x":{"label":"Where the cone ahead of the journal ends and the muzzle section begins, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":10.5,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-16-chf-barrel 3ab505012996 (Primary Arms' gallery, 05-2984_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its end faces (columns 2088.9 and 99.9, each behind its rim's arc: outline_rear_face and outline_front_face, tools/trace.py), 16.614 in apart through the same distortion (its scale along the barrel falls three times as fast as across it, and the thread's 28 to the inch read 4.25 px a pitch where it gives 4.248), stretched by 0.99322 to overall_length (16.501)","method":"the flange's rear face (column 1975.0) to where a line through the cone's radius (columns 715 to 780) meets a line through the muzzle section's (columns 240 to 690)","via":"harvest"}}]},"muzzle_run_od":{"label":"The muzzle section's diameter, between the cone ahead of the journal and the ring behind the shoulder","kind":"length","measurements":[{"id":"photo","value":0.667,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/geissele-16-chf-barrel 3ab505012996 (Primary Arms' gallery, 05-2984_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its gas block journal as the published .750 (45.874 px of radius over columns 805 to 905, the silhouette at grey 235: 122.33 px/in) and its extension's body as the Army's .999 (59.543 px over columns 1990 to 2080), through a radial lens distortion about the journal's middle (column 855) that those two fix (the extension's diameter 2.6% small, 1180 px off); the scale across the barrel at this station","method":"columns 240 to 690: 40.72 px of radius (± 0.2 px along it: a cylinder)","via":"harvest"}}]},"muzzle_ring_rear_x":{"label":"The rear end of the ring behind the muzzle shoulder, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":14.67,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-16-chf-barrel 3ab505012996 (Primary Arms' gallery, 05-2984_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its end faces (columns 2088.9 and 99.9, each behind its rim's arc: outline_rear_face and outline_front_face, tools/trace.py), 16.614 in apart through the same distortion (its scale along the barrel falls three times as fast as across it, and the thread's 28 to the inch read 4.25 px a pitch where it gives 4.248), stretched by 0.99322 to overall_length (16.501)","method":"the flange's rear face (column 1975.0) to the last column within 0.15 px of the ring's full radius (200: 42.61 px, 42.4 at 202 and falling)","via":"harvest"}}]},"muzzle_ring_foot_x":{"label":"Where the ring's rear chamfer meets the muzzle section, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":14.508,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-16-chf-barrel 3ab505012996 (Primary Arms' gallery, 05-2984_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its end faces (columns 2088.9 and 99.9, each behind its rim's arc: outline_rear_face and outline_front_face, tools/trace.py), 16.614 in apart through the same distortion (its scale along the barrel falls three times as fast as across it, and the thread's 28 to the inch read 4.25 px a pitch where it gives 4.248), stretched by 0.99322 to overall_length (16.501)","method":"the flange's rear face (column 1975.0) to the first column at the muzzle section's radius behind the ring (213: 40.86 px)","via":"harvest"}}]},"shoulder_x":{"label":"The muzzle shoulder ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":14.845,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-16-chf-barrel 3ab505012996 (Primary Arms' gallery, 05-2984_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its end faces (columns 2088.9 and 99.9, each behind its rim's arc: outline_rear_face and outline_front_face, tools/trace.py), 16.614 in apart through the same distortion (its scale along the barrel falls three times as fast as across it, and the thread's 28 to the inch read 4.25 px a pitch where it gives 4.248), stretched by 0.99322 to overall_length (16.501)","method":"the flange's rear face (column 1975.0) to the shoulder's face (column 178.4: the silhouette's step at 0.95 of the way from the thread's radius to the ring's, column 173.5, and the ring's front rim's ellipse there, the face seen from 21° off square: the rise from the thread's crests at column 169 is that ellipse)","via":"harvest"}}]},"thread_length":{"label":"The muzzle thread's length","kind":"length","measurements":[{"id":"photo","value":0.656,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-16-chf-barrel 3ab505012996 (Primary Arms' gallery, 05-2984_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its end faces (columns 2088.9 and 99.9, each behind its rim's arc: outline_rear_face and outline_front_face, tools/trace.py), 16.614 in apart through the same distortion (its scale along the barrel falls three times as fast as across it, and the thread's 28 to the inch read 4.25 px a pitch where it gives 4.248), stretched by 0.99322 to overall_length (16.501)","method":"the shoulder's face (column 178.4) to the muzzle's face (column 99.9, behind its rim's 12 px arc)","via":"harvest"}}]},"muzzle_od":{"label":"The diameter behind the muzzle thread","kind":"length","measurements":[{"id":"photo","value":0.705,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/geissele-16-chf-barrel 3ab505012996 (Primary Arms' gallery, 05-2984_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its gas block journal as the published .750 (45.874 px of radius over columns 805 to 905, the silhouette at grey 235: 122.33 px/in) and its extension's body as the Army's .999 (59.543 px over columns 1990 to 2080), through a radial lens distortion about the journal's middle (column 855) that those two fix (the extension's diameter 2.6% small, 1180 px off); the scale across the barrel at this station","method":"columns 180 to 196: 42.78 px of radius","via":"harvest"}}]},"outline_extension_od":{"label":"The extension's body as the side photo has it at the journal's scale","kind":"length","measurements":[{"id":"photo","value":0.9735,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/geissele-16-chf-barrel 3ab505012996 (Primary Arms' gallery, 05-2984_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its gas block journal's diameter as the published .750 (the silhouette at grey 235: 45.874 px of radius over columns 805 to 905, 122.33 px/in)","method":"the extension's body, columns 1990 to 2080: 59.543 px of radius (59.69 over its first 45 columns, 59.36 over its last 40)","via":"harvest"}}],"note":"Against extension_od (.999) this is how far the photo's scale across the barrel has fallen between the journal and the extension: 2.6% in 1180 px. The model takes it as a radial distortion about outline_journal_x (the scale along the barrel falls three times as fast), which puts the thread's pitch where the sellers' 28 to the inch has it."},"outline_extension_x":{"label":"The middle of the extension's body in the traced outline's own frame (from the silhouette's rear tip, at the journal's scale)","kind":"length","measurements":[{"id":"photo","value":0.576,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-16-chf-barrel 3ab505012996 (Primary Arms' gallery, 05-2984_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"the traced outline's scale: 122.33 px/in","method":"column 2035, the middle of the stretch outline_extension_od is read on, from the silhouette's rear tip (column 2105.5)","via":"harvest"}}]},"outline_journal_x":{"label":"The middle of the gas block journal in the traced outline's own frame (from the silhouette's rear tip, at the journal's scale): the centre of the photo's distortion","kind":"length","measurements":[{"id":"photo","value":10.222,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-16-chf-barrel 3ab505012996 (Primary Arms' gallery, 05-2984_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"the traced outline's scale: 122.33 px/in","method":"column 855, the middle of the stretch the journal's .750 is read on (805 to 905), from the silhouette's rear tip (column 2105.5)","via":"harvest"}}],"note":"Taken as the centre of the radial distortion: where the published .750 is read, the scale is the photo's own. The thread's pitch puts the centre within 75 px (0.6 in) of it."},"dimple_d":{"label":"The dimple on the journal for a gas block's set screw: its diameter at the journal's surface","kind":"length","measurements":[{"id":"photo","value":0.153,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/geissele-16-chf-barrel 3ab505012996 (Primary Arms' gallery, 05-2984_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its gas block journal as the published .750 (122.33 px/in at its middle)","method":"a circle through the dimple's rim on an eight-fold enlargement: columns 873.8 to 892.5, 18.7 px","via":"harvest"}}],"note":"A drilled spot under the port, opposite it (the sibling barrels' sellers: \"There is one dimple machined in for a gas block set screw\"; no page for 05-2984 says so). Not drawn: its depth isn't sourced (dimple_depth)."},"dimple_depth":{"label":"The dimple on the journal: its depth","kind":"length","measurements":[],"note":"No source: the photos look into it. Not drawn until a figure or a view with its edge on the silhouette is on file."},"collar_slot_w":{"label":"The slot along the collar's top, in line with the gas port: its width","kind":"length","measurements":[],"note":"Primary Arms' three-quarter photo (f8d6141d8f0c) shows a notch in the collar's top in line with the port, a few pixels across; the side photo has it on the far side. Not read, and not drawn."},"outline_flange_od":{"label":"The flange as the side photo has it at the journal's scale: the traced outline's scale reference","kind":"length","measurements":[{"id":"photo","value":1.14,"unit":"in","pm":0.007,"source":{"type":"photo","photo":"references/geissele-16-chf-barrel 3ab505012996 (Primary Arms' gallery, 05-2984_02: the barrel level on white, the muzzle at the left, the gas block's dimple toward the lens, 2200 x 1467)","scaleRef":"its gas block journal's diameter as the published .750 (the silhouette at grey 235: 45.874 px of radius over columns 805 to 905, 122.33 px/in)","method":"the silhouette's widest, columns 1962 to 1970: 69.73 px of radius against the journal's 45.874","via":"harvest"}}],"note":"Not the flange's size (flange_od, 1.166): at the journal's scale everything at the breech end of this photo reads 2.3 to 2.6% small (a radial distortion about the journal: overall_length). The traced outline is at this one scale throughout; the model corrects it by outline_extension_od, outline_extension_x and outline_journal_x."},"outline_rear_face":{"label":"The extension's rear face in the traced outline's own frame (from the silhouette's rear tip, at the journal's scale)","kind":"length","measurements":[{"id":"photo","value":0.136,"unit":"in","pm":0.017,"source":{"type":"photo","photo":"references/geissele-16-chf-barrel 3ab505012996 (Primary Arms' gallery, 05-2984_02: the barrel level on white, the muzzle at the left, 2200 x 1467)","scaleRef":"scale from geissele-16-chf-barrel.outline_flange_od = 1.14 in (y-extent 139 px → 122.0 px/in)","method":"the min end's face: the silhouette's tip at 0.017 less its rim's arc, 0.119 in of sag at radius 0.481023 (the end is seen from 13.9° off square; arc fitted over 121 rows, rms 0.012) of the traced outline (tools/trace.py); the extension's rear face in the outline's own frame (from its rear tip, at the journal's scale)","via":"harvest"}}],"note":"Where the outline is cut: the silhouette's tip is the rear rim's near side, which stands behind the face by the rim's arc."},"outline_front_face":{"label":"The muzzle's face in the traced outline's own frame (from the silhouette's rear tip, at the journal's scale)","kind":"length","measurements":[{"id":"photo","value":16.395,"unit":"in","pm":0.101,"source":{"type":"photo","photo":"references/geissele-16-chf-barrel 3ab505012996 (Primary Arms' gallery, 05-2984_02: the barrel level on white, the muzzle at the left, 2200 x 1467)","scaleRef":"scale from geissele-16-chf-barrel.outline_flange_od = 1.14 in (y-extent 139 px → 122.0 px/in)","method":"the max end's face: the silhouette's tip at 16.492 less its rim's arc, 0.096 in of sag at radius 0.240949 (the end is seen from 21.8° off square; arc fitted over 121 rows, rms 0.002) of the traced outline (tools/trace.py); the muzzle's face in the outline's own frame (from its rear tip, at the journal's scale)","via":"harvest"}}],"note":"Where the outline is cut: the silhouette's front tip is the muzzle rim's near side."}}},{"subject":"geissele-mk16-105-handguard","title":"Geissele Automatics 10.5 in Super Modular Rail MK16 M-LOK (05-1073B)","dimensions":{"weight":{"label":"Weight on the rifle (the handguard with its barrel nut)","kind":"mass","measurements":[{"id":"aerospace-arms","value":12.6,"unit":"oz","pm":0.05,"stated":"WEIGHT: 11oz (12.6oz w/ barrel nut)","source":{"type":"spec","publisher":"retailer","name":"Aerospace Arms, Geissele Automatics 10.5\" Super Modular Rail MK16 M-LOK - Black (05-1073B), Features and Specifications","url":"https://aerospacearms.com/geissele-automatics-10-5-super-modular-rail-mk16-m-lok-black/","retrieved":"2026-10-06","via":"harvest"}},{"id":"mister-guns","value":12.6,"unit":"oz","pm":0.05,"stated":"11 oz. weight (12.6 oz. w/ barrel nut)","source":{"type":"spec","publisher":"retailer","name":"Mister Guns, Geissele Automatics Super Modular Rail MK16 10.5\" M-LOK Black - 05-1073B, description","url":"https://shop.misterguns.com/product/14211/geissele-automatics-super-modular-rail-mk16-10-5-m-lok-black-05-1073b","retrieved":"2026-10-06","via":"harvest"}},{"id":"huckleberry","value":12.6,"unit":"oz","pm":0.05,"stated":"Weight 11 oz (12.6 oz w/ barrel nut)","source":{"type":"spec","publisher":"retailer","name":"Huckleberry Arms, Geissele 10.5\" Super Modular Rail MK16 M-LOK Black (05-1073B), specifications","url":"https://www.huckleberryarms.com/geissele-105-super-modular-rail-mk16-mlok-black-p/05-1073b.htm","retrieved":"2026-10-06","via":"harvest"}},{"id":"brownells","value":12.84,"unit":"oz","pm":0.005,"stated":"10.5\" WEIGHT: 11.2 oz ( 12.84oz w/barrel nut)","source":{"type":"spec","publisher":"retailer","name":"Brownells, GEISSELE AUTOMATICS LLC AR-15 MK16 SUPER MODULAR RAILS M-LOK, Specs (one page for the four lengths, a weight for each)","url":"https://www.brownells.com/gun-parts/rifle-parts/rifle-handguards-parts/ar-15-mk16-super-modular-rails-m-lok/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"aerospace-arms","reason":"Three sellers' pages for this one product (05-1073B) against one page for four lengths; the model's metal as aluminium weighs within a few percent of the handguard this pair leaves (weight_handguard). Only the maker settles it, and its page isn't read."},"note":"Sellers give two pairs of figures for this length: 11 oz (12.6 with the barrel nut) on four pages of four sellers, and 11.2 oz (12.84 with it) on Brownells' one page for the four lengths, whose figure for the 15 in rail is also its own. The barrel nut is what it mounts by and comes with it; a build weighs a pair's second figure. The maker's own page isn't opened."},"weight_handguard":{"label":"Weight, the handguard alone","kind":"mass","measurements":[{"id":"aerospace-arms","value":11,"unit":"oz","pm":0.5,"stated":"WEIGHT: 11oz (12.6oz w/ barrel nut)","source":{"type":"spec","publisher":"retailer","name":"Aerospace Arms, Geissele Automatics 10.5\" Super Modular Rail MK16 M-LOK - Black (05-1073B), Features and Specifications","url":"https://aerospacearms.com/geissele-automatics-10-5-super-modular-rail-mk16-m-lok-black/","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":11,"unit":"oz","pm":0.5,"stated":"Weight 11 oz.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics MK16 Free Float AR-15 Handguard - M-LOK - 10.5\" (05-1073B), specifications","url":"https://www.primaryarms.com/geissele-automatics-super-modular-rail-mk16-m-lok-black-10.5in","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms-ddc","value":11,"unit":"oz","pm":0.5,"stated":"Weight 11 oz.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics MK16 Free Float AR-15 Handguard - M-LOK - 10.5\" - DDC (05-1073S), specifications","url":"https://www.primaryarms.com/geissele-automatics-super-modular-rail-mk16-m-lok-ddc-10.5in","retrieved":"2026-10-06","via":"harvest"}},{"id":"mister-guns","value":11,"unit":"oz","pm":0.5,"stated":"11 oz. weight (12.6 oz. w/ barrel nut)","source":{"type":"spec","publisher":"retailer","name":"Mister Guns, Geissele Automatics Super Modular Rail MK16 10.5\" M-LOK Black - 05-1073B, description","url":"https://shop.misterguns.com/product/14211/geissele-automatics-super-modular-rail-mk16-10-5-m-lok-black-05-1073b","retrieved":"2026-10-06","via":"harvest"}},{"id":"huckleberry","value":11,"unit":"oz","pm":0.5,"stated":"Weight 11 oz (12.6 oz w/ barrel nut)","source":{"type":"spec","publisher":"retailer","name":"Huckleberry Arms, Geissele 10.5\" Super Modular Rail MK16 M-LOK Black (05-1073B), specifications","url":"https://www.huckleberryarms.com/geissele-105-super-modular-rail-mk16-mlok-black-p/05-1073b.htm","retrieved":"2026-10-06","via":"harvest"}},{"id":"brownells","value":11.2,"unit":"oz","pm":0.05,"stated":"10.5\" WEIGHT: 11.2 oz ( 12.84oz w/barrel nut)","source":{"type":"spec","publisher":"retailer","name":"Brownells, GEISSELE AUTOMATICS LLC AR-15 MK16 SUPER MODULAR RAILS M-LOK, Specs (one page for the four lengths, a weight for each)","url":"https://www.brownells.com/gun-parts/rifle-parts/rifle-handguards-parts/ar-15-mk16-super-modular-rails-m-lok/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"aerospace-arms","reason":"The pair adopted for the weight on the rifle; a figure in whole ounces, which Brownells' 11.2 is inside."},"note":"The same two pairs' first figures: 11 oz on five pages (Primary Arms gives it alone, for each colour) and Brownells' 11.2."},"length":{"label":"Length, end to end (its rear face to its muzzle end, the tabs behind the rear face left out)","kind":"length","measurements":[{"id":"aerospace-arms","value":10.5,"unit":"in","pm":0.05,"stated":"LENGTH: 10.5\"","source":{"type":"spec","publisher":"retailer","name":"Aerospace Arms, Geissele Automatics 10.5\" Super Modular Rail MK16 M-LOK - Black (05-1073B), Features and Specifications","url":"https://aerospacearms.com/geissele-automatics-10-5-super-modular-rail-mk16-m-lok-black/","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":10.5,"unit":"in","pm":0.05,"stated":"Handguard Length 10.5","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics MK16 Free Float AR-15 Handguard - M-LOK - 10.5\" (05-1073B), specifications","url":"https://www.primaryarms.com/geissele-automatics-super-modular-rail-mk16-m-lok-black-10.5in","retrieved":"2026-10-06","via":"harvest"}},{"id":"huckleberry","value":10.5,"unit":"in","pm":0.05,"stated":"Length 10.5\"","source":{"type":"spec","publisher":"retailer","name":"Huckleberry Arms, Geissele 10.5\" Super Modular Rail MK16 M-LOK Black (05-1073B), specifications","url":"https://www.huckleberryarms.com/geissele-105-super-modular-rail-mk16-mlok-black-p/05-1073b.htm","retrieved":"2026-10-06","via":"harvest"}},{"id":"photo","value":10.505,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/geissele-mk16-105-handguard 9919885fa19f (Primary Arms' gallery for 05-1073S, 05-1073S_02.jpg: the handguard alone in Desert Dirt Color, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own top rail's 25 slots at the Picatinny pitch (std.picatinny.slot_pitch): a quadratic fit of their centres, 69.92 px a pitch at the muzzle end and 68.41 at the rear","method":"the rail's front end (px 99, its near edge: true column 110.5) to its rear end (px 1968: true column 1954.2): rail coordinates -1.076 and 25.588, 26.66 pitches; the lens stood over column 950 and 31 in from the rifle's middle plane (the rail's notches narrow from 38 px there to 17.0 at the muzzle end and 14.8 at the rear, as its two edges part), so what stands z nearer the lens reads large about that column by 31 / (31 - z): 1.0263 on the side face, 1.0137 at the rail's near edge (scratch/m2.py)","via":"harvest"}}],"adopt":{"from":"photo","reason":"Its own rail's 25 slots and two end lands count 10.505 in, which is what the model's rail and slots add up to; the sellers' 10.5 in agrees within its last digit."},"note":"The sellers' 10.5 in, and by its own rail it is that: 25 slots and a land at each end, 10.505 in. Its rail runs the whole length: on the level photo the rail's rear end and the body's rear face are one plane within 0.01 in once each is read at its own depth, and the rail's nose and the side faces' tips at the muzzle end within 0.01."},"width":{"label":"Width across the side faces (3 to 9 o'clock)","kind":"length","measurements":[{"id":"aerospace-arms","value":1.59,"unit":"in","pm":0.005,"stated":"OUTER DIAMETER (DAQ*): 1.59\" [...] *DAQ - Distance Across Quadrants","source":{"type":"spec","publisher":"retailer","name":"Aerospace Arms, Geissele Automatics 10.5\" Super Modular Rail MK16 M-LOK - Black (05-1073B), Features and Specifications","url":"https://aerospacearms.com/geissele-automatics-10-5-super-modular-rail-mk16-m-lok-black/","retrieved":"2026-10-06","via":"harvest"}},{"id":"huckleberry","value":1.59,"unit":"in","pm":0.005,"stated":"Outer Diameter (DAQ*) 1.59\"","source":{"type":"spec","publisher":"retailer","name":"Huckleberry Arms, Geissele 10.5\" Super Modular Rail MK16 M-LOK Black (05-1073B), specifications","url":"https://www.huckleberryarms.com/geissele-105-super-modular-rail-mk16-mlok-black-p/05-1073b.htm","retrieved":"2026-10-06","via":"harvest"}},{"id":"mister-guns","value":1.59,"unit":"in","pm":0.005,"stated":"1.26”/1.59” inner/outer diameter","source":{"type":"spec","publisher":"retailer","name":"Mister Guns, Geissele Automatics Super Modular Rail MK16 10.5\" M-LOK Black - 05-1073B, description","url":"https://shop.misterguns.com/product/14211/geissele-automatics-super-modular-rail-mk16-10-5-m-lok-black-05-1073b","retrieved":"2026-10-06","via":"harvest"}},{"id":"brownells","value":1.59,"unit":"in","pm":0.005,"stated":"OUTER DIAMETER (DAQ*): 1.59\"","source":{"type":"spec","publisher":"retailer","name":"Brownells, GEISSELE AUTOMATICS LLC AR-15 MK16 SUPER MODULAR RAILS M-LOK, Specs (one page for the four lengths, a weight for each)","url":"https://www.brownells.com/gun-parts/rifle-parts/rifle-handguards-parts/ar-15-mk16-super-modular-rails-m-lok/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"aerospace-arms","reason":"Four sellers state the one figure."},"note":"The sellers' \"OUTER DIAMETER (DAQ*)\" with \"*DAQ - Distance Across Quadrants\": the distance across two opposite faces that carry M-LOK slots."},"height":{"label":"Height (the rail's top to the bottom of the clamp block at its rear end)","kind":"length","measurements":[{"id":"aerospace-arms","value":2.39,"unit":"in","pm":0.005,"stated":"HEIGHT: 2.39\"","source":{"type":"spec","publisher":"retailer","name":"Aerospace Arms, Geissele Automatics 10.5\" Super Modular Rail MK16 M-LOK - Black (05-1073B), Features and Specifications","url":"https://aerospacearms.com/geissele-automatics-10-5-super-modular-rail-mk16-m-lok-black/","retrieved":"2026-10-06","via":"harvest"}},{"id":"huckleberry","value":2.39,"unit":"in","pm":0.005,"stated":"Height 2.39\"","source":{"type":"spec","publisher":"retailer","name":"Huckleberry Arms, Geissele 10.5\" Super Modular Rail MK16 M-LOK Black (05-1073B), specifications","url":"https://www.huckleberryarms.com/geissele-105-super-modular-rail-mk16-mlok-black-p/05-1073b.htm","retrieved":"2026-10-06","via":"harvest"}},{"id":"mister-guns","value":2.39,"unit":"in","pm":0.005,"stated":"2.39” height","source":{"type":"spec","publisher":"retailer","name":"Mister Guns, Geissele Automatics Super Modular Rail MK16 10.5\" M-LOK Black - 05-1073B, description","url":"https://shop.misterguns.com/product/14211/geissele-automatics-super-modular-rail-mk16-10-5-m-lok-black-05-1073b","retrieved":"2026-10-06","via":"harvest"}},{"id":"brownells","value":2.39,"unit":"in","pm":0.005,"stated":"HEIGHT: 2.39\"","source":{"type":"spec","publisher":"retailer","name":"Brownells, GEISSELE AUTOMATICS LLC AR-15 MK16 SUPER MODULAR RAILS M-LOK, Specs (one page for the four lengths, a weight for each)","url":"https://www.brownells.com/gun-parts/rifle-parts/rifle-handguards-parts/ar-15-mk16-super-modular-rails-m-lok/","retrieved":"2026-10-06","via":"harvest"}},{"id":"photo","value":2.42,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-mk16-105-handguard 9919885fa19f (Primary Arms' gallery for 05-1073S, 05-1073S_02.jpg: the handguard alone in Desert Dirt Color, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own rail's slots at the rear end (68.4 px a pitch, 173.6 px/in on the middle plane; 176.0 at the rail's near edge and 178.2 on the side face)","method":"the rail's tooth tops (row 521.3) to the clamp block's bottom edge (row 950) at columns 1854 to 1904: 428.7 px, each half read at its own depth about the image's middle row; the photo is from a little above (the teeth's tops show), which is what it reads large by (scratch/m2.py)","via":"harvest"}}],"adopt":{"from":"aerospace-arms","reason":"Four sellers state the one figure; the level photo reads it within 1.3% as the rail's top to the clamp block's bottom, from a little above."},"note":"What the sellers' 2.39 in spans is read on the level photo, as on the other two lengths': the rail's top to the bottom of the clamp block under the rear end."},"inside_diameter":{"label":"Inside diameter","kind":"length","measurements":[{"id":"aerospace-arms","value":1.26,"unit":"in","pm":0.005,"stated":"INNER DIAMETER: 1.26\"","source":{"type":"spec","publisher":"retailer","name":"Aerospace Arms, Geissele Automatics 10.5\" Super Modular Rail MK16 M-LOK - Black (05-1073B), Features and Specifications","url":"https://aerospacearms.com/geissele-automatics-10-5-super-modular-rail-mk16-m-lok-black/","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":1.26,"unit":"in","pm":0.005,"stated":"Inner Diameter 1.26 in.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics MK16 Free Float AR-15 Handguard - M-LOK - 10.5\" (05-1073B), specifications","url":"https://www.primaryarms.com/geissele-automatics-super-modular-rail-mk16-m-lok-black-10.5in","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms-ddc","value":1.26,"unit":"in","pm":0.005,"stated":"Inner Diameter 1.26 in.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics MK16 Free Float AR-15 Handguard - M-LOK - 10.5\" - DDC (05-1073S), specifications","url":"https://www.primaryarms.com/geissele-automatics-super-modular-rail-mk16-m-lok-ddc-10.5in","retrieved":"2026-10-06","via":"harvest"}},{"id":"huckleberry","value":1.26,"unit":"in","pm":0.005,"stated":"Inner Diameter 1.26\"","source":{"type":"spec","publisher":"retailer","name":"Huckleberry Arms, Geissele 10.5\" Super Modular Rail MK16 M-LOK Black (05-1073B), specifications","url":"https://www.huckleberryarms.com/geissele-105-super-modular-rail-mk16-mlok-black-p/05-1073b.htm","retrieved":"2026-10-06","via":"harvest"}},{"id":"mister-guns","value":1.26,"unit":"in","pm":0.005,"stated":"1.26”/1.59” inner/outer diameter","source":{"type":"spec","publisher":"retailer","name":"Mister Guns, Geissele Automatics Super Modular Rail MK16 10.5\" M-LOK Black - 05-1073B, description","url":"https://shop.misterguns.com/product/14211/geissele-automatics-super-modular-rail-mk16-10-5-m-lok-black-05-1073b","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"aerospace-arms","reason":"Five pages of four sellers state the one figure."},"note":"Sellers' \"INNER DIAMETER\". As on the other two lengths, the model takes it as the circle its flat inner walls touch."},"rear_face_x":{"label":"Its rear face against the receiver's front face (negative: behind it)","kind":"length","measurements":[{"id":"derived","value":-0.445,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"0in - {std.ar15.upper_barrel_thread_length}","via":"harvest"}}],"note":"No page read says where it stops, and no photo of it mounted is on file. As the other two lengths: it slides back over its barrel nut, and its rear face is taken to meet the receiver's front shoulder, where the barrel-nut thread begins (std.ar15.upper_barrel_thread_length behind the front face), with no gap. A check: its rail's first slot then stands 0.01 in from where the receiver's own row of slots would continue (bcm-m4-upper: 13 slots from 1.31 in at the standard's pitch)."},"tab_length":{"label":"Its lower tabs' reach behind its rear face","kind":"length","measurements":[{"id":"derived","value":0.26,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.tab_length}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws). On this length's level photo the lower tab's end (px 2024) stands 0.25 in behind the rear face's edge (px 1979) at the side face's scale."},"rear_x":{"label":"The outline's rear end (its lower tabs' ends) against the receiver's front face (negative: behind it)","kind":"length","measurements":[{"id":"derived","value":-0.705,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{.rear_face_x} - {.tab_length}","via":"harvest"}}]},"overall_length":{"label":"Length over all, its lower tabs' ends to its muzzle end","kind":"length","measurements":[{"id":"derived","value":10.765,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{.length} + {.tab_length}","via":"harvest"}}]},"tab_top_below_bore":{"label":"Its lower tabs' top edge below the bore axis","kind":"length","measurements":[{"id":"derived","value":0.27,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.tab_top_below_bore}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws). Rows 787 to 852 on this length's level photo, the 15 in rail's within 0.03."},"tab_bottom_below_bore":{"label":"Its lower tabs' bottom edge below the bore axis","kind":"length","measurements":[{"id":"derived","value":0.64,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.tab_bottom_below_bore}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws)."},"tab_screw_d":{"label":"A tab's set screw, its diameter as it shows from the side","kind":"length","measurements":[{"id":"derived","value":0.14,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.tab_screw_d}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws). The screw's round end is at px (2005, 835) on this length's level photo."},"tongue_length":{"label":"Its upper tabs' reach behind its rear face","kind":"length","measurements":[{"id":"derived","value":0.12,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.tongue_length}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws). This length's level photo reads 0.10 (px 1979 to 1997)."},"upper_tab_gap":{"label":"The opening between its two upper tabs","kind":"length","measurements":[{"id":"derived","value":0.638,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"2 * {bcm-m4-upper.side_half_width}","via":"harvest"}}],"note":"As the other two lengths': not measured (no view shows it square on); the tabs stand beside a mil-spec receiver's flat sides under its rail and are drawn against those flats with no clearance. Aerospace Arms: \"These handguards are designed to work with Mil-Spec M4 upper receivers. The compatibility with billet receiver sets is unknown.\""},"tongue_bottom_above_bore":{"label":"Its upper tabs' bottom edge above the bore axis","kind":"length","measurements":[{"id":"derived","value":0.545,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.tongue_bottom_above_bore}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws)."},"tongue_top_above_bore":{"label":"Its upper tabs' top edge above the bore axis","kind":"length","measurements":[{"id":"derived","value":0.727,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.tongue_top_above_bore}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws)."},"rail_top_above_bore":{"label":"Its rail's top above the bore axis","kind":"length","measurements":[{"id":"derived","value":1.2,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.rail_top_above_bore}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws). This length's level photo reads the rail's tooth tops 1.22 in above the middle of the side rows' slots (rows 514.5 and 731 at the muzzle end, 179 px/in), from a little above."},"body_bottom_below_bore":{"label":"The tube's bottom flat below the bore axis","kind":"length","measurements":[{"id":"derived","value":0.86,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.body_bottom_below_bore}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws). This length's level photo reads the tube's bottom edge 0.86 in below the middle of the side rows' slots (rows 884 and 731 at 179 px/in)."},"side_flat_height":{"label":"The side faces' height (crease to crease)","kind":"length","measurements":[{"id":"derived","value":0.6,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.side_flat_height}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws)."},"upper_face_angle":{"label":"The faces between the sides and the rail: where their normal points, about the bore from the top (12 o'clock) toward the side","kind":"angle","measurements":[{"id":"derived","value":45,"unit":"deg","pm":2,"source":{"type":"derived","expr":"{geissele-mk16-135-handguard.upper_face_angle}","via":"harvest"}}],"note":"The family's section, read on the muzzle end of the 13.5 in rail (two views square on an end with a known size in frame): taken from that rail's ledger by reference. No view is square on this length's end; Primary Arms' view of this length from ahead (2b231cbaae86) shows the same end: the rail on its neck, the side faces, the faces between."},"lower_face_angle":{"label":"The faces between the sides and the bottom: where their normal points, about the bore from the top (12 o'clock) toward the side","kind":"angle","measurements":[{"id":"derived","value":131.4,"unit":"deg","pm":1,"source":{"type":"derived","expr":"{geissele-mk16-135-handguard.lower_face_angle}","via":"harvest"}}],"note":"The family's section, read on the muzzle end of the 13.5 in rail (two views square on an end with a known size in frame): taken from that rail's ledger by reference. No view is square on this length's end; its view from ahead (2b231cbaae86) shows the lower faces longer than the upper ones and a bottom flat with the trough's notch in it, as the 13.5 in rail's."},"upper_face_distance":{"label":"The upper faces' distance from the bore axis, along their normal","kind":"length","measurements":[{"id":"derived","value":0.774282,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{.width} / 2 * sin({.upper_face_angle}) + {.side_flat_height} / 2 * cos({.upper_face_angle})","via":"harvest"}}],"note":"Through the side faces' upper creases at the faces' angle."},"lower_face_distance":{"label":"The lower faces' distance from the bore axis, along their normal","kind":"length","measurements":[{"id":"derived","value":0.794732,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{.width} / 2 * sin({.lower_face_angle}) - {.side_flat_height} / 2 * cos({.lower_face_angle})","via":"harvest"}}],"note":"Through the side faces' lower creases at the faces' angle."},"bottom_flat_width":{"label":"The bottom flat's width","kind":"length","measurements":[{"id":"derived","value":0.61,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-135-handguard.bottom_flat_width}","via":"harvest"}}],"note":"The family's section, read on the muzzle end of the 13.5 in rail (two views square on an end with a known size in frame): taken from that rail's ledger by reference. No view is square on this length's end; a check on lower_face_angle, not what the model draws from."},"neck_base_above_bore":{"label":"Where the upper faces end and the neck under the rail begins, above the bore","kind":"length","measurements":[{"id":"derived","value":0.695,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.neck_base_above_bore}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws)."},"neck_chamfer_height":{"label":"The slope between the upper faces and the neck's walls, its height","kind":"length","measurements":[{"id":"derived","value":0.08,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.neck_chamfer_height}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws)."},"neck_width":{"label":"The neck's width under the rail","kind":"length","measurements":[{"id":"derived","value":0.61,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.neck_width}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws)."},"channel_width":{"label":"The channel under the rail (the gas tube's), its width","kind":"length","measurements":[{"id":"derived","value":0.47,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.channel_width}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws)."},"channel_roof_below_top":{"label":"The channel's roof below the rail's top","kind":"length","measurements":[{"id":"derived","value":0.18,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.channel_roof_below_top}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws)."},"trough_width":{"label":"The troughs along the inside of the bottom, the side faces and the upper faces: their width","kind":"length","measurements":[{"id":"derived","value":0.49,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{geissele-mk16-135-handguard.trough_width}","via":"harvest"}}],"note":"The family's section, read on the muzzle end of the 13.5 in rail (two views square on an end with a known size in frame): taken from that rail's ledger by reference. No view is square on this length's end; its view from ahead (2b231cbaae86) shows the notch of the bottom's trough in the muzzle face and the side walls' thin ends."},"trough_wall":{"label":"The wall a trough's floor leaves, its thickness","kind":"length","measurements":[{"id":"derived","value":0.094,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-135-handguard.trough_wall}","via":"harvest"}}],"note":"The family's section, read on the muzzle end of the 13.5 in rail (two views square on an end with a known size in frame): taken from that rail's ledger by reference. No view is square on this length's end."},"rail_slots":{"label":"Slots in its top rail","kind":"count","measurements":[{"id":"photo","value":25,"unit":"count","source":{"type":"photo","photo":"references/geissele-mk16-105-handguard 9919885fa19f (Primary Arms' gallery for 05-1073S, 05-1073S_02.jpg: the handguard alone in Desert Dirt Color, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"none: a count","method":"the notches between the teeth along the top edge: 25, centres from px 184.9 to px 1846.7, each 68.6 to 70.2 px from the next with none missing; a longer tooth at the rear end and a short sloped one at the front (scratch/m2.py); 25 on the same rail's right side (9305c7dae050)","via":"harvest"}}]},"rail_slot0_from_rear":{"label":"Its rail's rearmost slot (its centre) ahead of its rear face","kind":"length","measurements":[{"id":"photo","value":0.625,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-mk16-105-handguard 9919885fa19f (Primary Arms' gallery for 05-1073S, 05-1073S_02.jpg: the handguard alone in Desert Dirt Color, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own top rail's 25 slots at the Picatinny pitch (std.picatinny.slot_pitch): a quadratic fit of their centres, 69.92 px a pitch at the muzzle end and 68.41 at the rear","method":"the rail's rear end (px 1968, its near edge: true column 1954.2, rail coordinate 25.588) behind the rearmost slot's centre (px 1846.7, coordinate 24): 1.588 pitches; the body's rear face (px 1979 on the side face: true column 1952.6) is the same plane within 0.01 in (scratch/m2.py)","via":"harvest"}}],"note":"The 13.5 in rail's reads 0.62: the family's rear end."},"rail_slot0_x":{"label":"Its rail's rearmost slot (its centre) ahead of the receiver's front face","kind":"length","measurements":[{"id":"derived","value":0.18,"unit":"in","pm":0.045,"source":{"type":"derived","expr":"{.rear_face_x} + {.rail_slot0_from_rear}","via":"harvest"}}]},"rail_front_from_last_slot":{"label":"Its rail's front end ahead of its last slot's centre","kind":"length","measurements":[{"id":"photo","value":0.424,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-mk16-105-handguard 9919885fa19f (Primary Arms' gallery for 05-1073S, 05-1073S_02.jpg: the handguard alone in Desert Dirt Color, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own top rail's 25 slots at the Picatinny pitch (std.picatinny.slot_pitch): a quadratic fit of their centres, 69.92 px a pitch at the muzzle end and 68.41 at the rear","method":"the rail's front end (px 99, its near edge: true column 110.5, rail coordinate -1.076) ahead of the frontmost slot's centre (px 184.9, coordinate 0): 1.076 pitches; the side faces' tips (px 88 on the side face: true column 110.1) are the same plane (scratch/m2.py)","via":"harvest"}}],"note":"Shorter than the 13.5 in rail's 0.685: this length's last tooth is a short one, sloped off at its top (rail_nose_length)."},"rail_nose_length":{"label":"The slope at the rail's front end, its length along the rail","kind":"length","measurements":[{"id":"photo","value":0.23,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-mk16-105-handguard 9919885fa19f (Primary Arms' gallery for 05-1073S, 05-1073S_02.jpg: the handguard alone in Desert Dirt Color, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own rail's slots at the muzzle end, at the rail's near edge: 179.8 px/in","method":"the top edge leaves the tooth tops' level (row 515.5) at px 140 and reaches the front end at px 99: 41 px (scratch/m2.py)","via":"harvest"}}],"note":"The rail's top is sloped down to the muzzle end over its last quarter inch, as the 13.5 in rail's: a face of its own in Primary Arms' view from ahead (2b231cbaae86), which also shows a bevel down each side of it that isn't drawn."},"rail_nose_drop":{"label":"The slope at the rail's front end, how far its front edge is below the rail's top","kind":"length","measurements":[{"id":"photo","value":0.09,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-mk16-105-handguard 9919885fa19f (Primary Arms' gallery for 05-1073S, 05-1073S_02.jpg: the handguard alone in Desert Dirt Color, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own rail's slots at the muzzle end, at the rail's near edge: 179.8 px/in","method":"the top edge at the front end (row 531.1 at px 100) below the tooth tops (row 515.5): 15.6 px, a pixel more at the very end (scratch/m2.py)","via":"harvest"}}]},"mlok_side_slots":{"label":"M-LOK slots on each side face (3 and 9 o'clock)","kind":"count","measurements":[{"id":"photo","value":5,"unit":"count","source":{"type":"photo","photo":"references/geissele-mk16-105-handguard 9919885fa19f (Primary Arms' gallery for 05-1073S, 05-1073S_02.jpg: the handguard alone in Desert Dirt Color, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"none: a count","method":"the middle row's slots, light showing through each: five, 270 to 282 px apart (scratch/m2.py); five on the same rail's right side (9305c7dae050)","via":"harvest"}}]},"mlok_lower_slots":{"label":"M-LOK slots on each lower face (between the sides and the bottom)","kind":"count","measurements":[{"id":"photo","value":5,"unit":"count","source":{"type":"photo","photo":"references/geissele-mk16-105-handguard 9919885fa19f (Primary Arms' gallery for 05-1073S, 05-1073S_02.jpg: the handguard alone in Desert Dirt Color, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"none: a count","method":"the lower row's slots, light showing through each: five, their ends within 0.02 in of the side row's (rail coordinates -0.96 to 14.78 against -0.89 to 14.80 for their front ends) (scratch/m2.py); five on the same rail's right side (9305c7dae050)","via":"harvest"}}]},"mlok_upper_slots":{"label":"M-LOK slots on each upper face (between the sides and the rail)","kind":"count","measurements":[{"id":"photo","value":4,"unit":"count","source":{"type":"photo","photo":"references/geissele-mk16-105-handguard 9919885fa19f (Primary Arms' gallery for 05-1073S, 05-1073S_02.jpg: the handguard alone in Desert Dirt Color, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"none: a count","method":"the upper row's slots, light showing through each: four, each over one of the side row's front four (their rear ends at px 381, 661, 941, 1216 against the side row's 377, 663, 946, 1213), and behind them the socket's hole with light through it (px 1456 to 1492); four on the same rail's right side (9305c7dae050)","via":"harvest"}}],"note":"One fewer than the side faces: where the rearmost would be, the upper face carries a sling swivel socket."},"mlok_bottom_slots":{"label":"M-LOK slots on its underside (6 o'clock)","kind":"count","measurements":[{"id":"derived","value":5,"unit":"count","source":{"type":"derived","expr":"{.mlok_side_slots}","via":"harvest"}}],"note":"The row is the sellers' sentence (\"M-LOK slots on every quadrant\", Aerospace Arms and Primary Arms) and no photo of this length's: no view on file shows its underside, from below or from inside. The 13.5 in rail's foremost four are seen from inside its muzzle end at the side rows' stations, and this length's row is taken the same way: the side rows' five, which is what fits ahead of the clamp block (mlok_bottom_slot0_x). An assumption, not a count."},"mlok_bottom_slot0_x":{"label":"The underside's rearmost M-LOK slot (its centre) ahead of the receiver's front face","kind":"length","measurements":[{"id":"derived","value":2.815,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{.mlok_side_slot0_x}","via":"harvest"}}],"note":"Not seen: taken at the side rows' stations. The clamp block and its split take the rear of the bottom; the side rows' rearmost slot begins 2.63 in ahead of the rear face, 0.26 in ahead of where the block's front ramp ends on the level photo (2.37), so the row starts there with all five ahead of the block. An assumption."},"mlok_side_slot0_from_rear":{"label":"The side faces' rearmost M-LOK slot (its centre) ahead of the rear face","kind":"length","measurements":[{"id":"photo","value":3.26,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-mk16-105-handguard 9919885fa19f (Primary Arms' gallery for 05-1073S, 05-1073S_02.jpg: the handguard alone in Desert Dirt Color, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own top rail's 25 slots at the Picatinny pitch (std.picatinny.slot_pitch): a quadratic fit of their centres, 69.92 px a pitch at the muzzle end and 68.41 at the rear; the lens stood over column 950 and 31 in from the rifle's middle plane (the rail's notches narrow from 38 px there to 17.0 at the muzzle end and 14.8 at the rear, as its two edges part), so what stands z nearer the lens reads large about that column by 31 / (31 - z): 1.0263 on the side face, 1.0137 at the rail's near edge","method":"the side row's slots' own edges where they bound the light (the rear ends of the three ahead of the lens, the front ends of the two behind it), each brought to its true place: rail coordinates 2.950, 6.953, 10.928 and 11.717, 15.694, 3.98 to 4.00 pitches apart; the rearmost slot's rear end at 18.907 by both, 6.68 pitches (2.63 in) ahead of the rear face (25.588), its centre half a slot (std.mlok.slot_length) further. Read straight on the side face, the same slot's rear end (px 1509) is 2.634 in ahead of the rear face's edge (px 1979) at 178.4 px/in (scratch/m2.py)","via":"harvest"}}],"note":"Further forward than on the 13.5 in rail (3.10) and the 15 in (3.08): the rows are set from the muzzle end, where every length's foremost slot ends a third of an inch short of it (0.33 in here, 0.32 on the 13.5 in), and this length's five leave more of the body whole ahead of the clamp block."},"mlok_side_slot0_x":{"label":"The side and lower faces' rearmost M-LOK slot (its centre) ahead of the receiver's front face","kind":"length","measurements":[{"id":"derived","value":2.815,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{.rear_face_x} + {.mlok_side_slot0_from_rear}","via":"harvest"}}]},"mlok_upper_slot0_x":{"label":"The upper faces' rearmost M-LOK slot (its centre) ahead of the receiver's front face","kind":"length","measurements":[{"id":"derived","value":4.389803,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{.mlok_side_slot0_x} + {std.mlok.slot_pitch}","via":"harvest"}}],"note":"One slot pitch ahead of the side faces' rearmost: the upper rows have the side rows' front four."},"mlok_upper_row_above_bore":{"label":"The upper rows of slots, their middle line above the bore","kind":"length","measurements":[{"id":"derived","value":0.51,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.mlok_upper_row_above_bore}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws). This length's level photo has the upper row's light at rows 641 to 654 and the side row's at 715 to 748."},"mlok_lower_row_below_bore":{"label":"The lower rows of slots, their middle line below the bore","kind":"length","measurements":[{"id":"derived","value":0.565,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.mlok_lower_row_below_bore}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws)."},"reach_inside":{"label":"The room inside its faces, from a face in to the barrel (what an M-LOK accessory's nuts may take)","kind":"length","measurements":[],"note":"Not sourced: it depends on the barrel and gas block under it, other parts. Its walls are 0.165 in by the sellers' two figures (1.59 across, 1.26 inside), 0.09 under a trough."},"socket_from_rear":{"label":"The sling swivel sockets (their centres) ahead of the rear face","kind":"length","measurements":[{"id":"derived","value":2.77,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.socket_from_rear}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws). This length's level photo has the socket's hole, light through it, at px 1456 to 1492: its centre on the near face 2.76 in ahead of the rear face once the far face's shift is taken out."},"socket_above_bore":{"label":"The sling swivel sockets' centres above the bore","kind":"length","measurements":[{"id":"derived","value":0.585,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.socket_above_bore}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws)."},"socket_ring_d":{"label":"A sling swivel socket's cup, its outside diameter","kind":"length","measurements":[{"id":"derived","value":0.545,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.socket_ring_d}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws)."},"socket_hole_d":{"label":"A sling swivel socket's hole, its diameter","kind":"length","measurements":[{"id":"derived","value":0.31,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.socket_hole_d}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws)."},"cross_bolt_front_from_rear":{"label":"The front cross bolt (its centre) ahead of the rear face","kind":"length","measurements":[{"id":"derived","value":1.57,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.cross_bolt_front_from_rear}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws). This length's level photo has the plate's front hole at px (1700, 868): 1.564 in ahead of the rear face's edge (px 1979) at the side face's scale."},"cross_bolt_rear_from_rear":{"label":"The rear cross bolt (its centre) ahead of the rear face","kind":"length","measurements":[{"id":"derived","value":0.55,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.cross_bolt_rear_from_rear}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws). This length's level photo has the plate's rear hole at px (1880, 893): 0.555 in ahead of the rear face's edge."},"cross_bolt_front_below_bore":{"label":"The front cross bolt's centre below the bore","kind":"length","measurements":[{"id":"derived","value":0.745,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.cross_bolt_front_below_bore}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws)."},"cross_bolt_rear_below_bore":{"label":"The rear cross bolt's centre below the bore","kind":"length","measurements":[{"id":"derived","value":0.835,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.cross_bolt_rear_below_bore}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws)."},"cross_bolt_hole_d":{"label":"A cross bolt's threaded hole in the left side's plate, its diameter","kind":"length","measurements":[{"id":"derived","value":0.21,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.cross_bolt_hole_d}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws)."},"cross_bolt_head_d":{"label":"A cross bolt's Torx head on the right side, its diameter","kind":"length","measurements":[{"id":"derived","value":0.32,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.cross_bolt_head_d}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws). Primary Arms' photo of this length's right side (9305c7dae050) shows the two Torx heads standing in their counterbores."},"cross_bolt_counterbore_d":{"label":"A cross bolt's counterbore on the right side, its diameter","kind":"length","measurements":[{"id":"derived","value":0.46,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.cross_bolt_counterbore_d}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws)."},"clamp_gap_width":{"label":"The clamp block's split along its underside, its width","kind":"length","measurements":[{"id":"derived","value":0.51,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.clamp_gap_width}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws)."},"plate_lobe_d":{"label":"The left side's nut plate, each end's width round its bolt hole","kind":"length","measurements":[{"id":"derived","value":0.52,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.plate_lobe_d}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws)."},"plate_bar_height":{"label":"The nut plate's bar between its two ends, its height","kind":"length","measurements":[{"id":"derived","value":0.2,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.plate_bar_height}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws)."}}},{"subject":"geissele-mk16-135-handguard","title":"Geissele Automatics 13.5 in Super Modular Rail MK16 M-LOK (05-650B)","dimensions":{"weight":{"label":"Weight on the rifle (the handguard with its barrel nut)","kind":"mass","measurements":[{"id":"aerospace-arms","value":14.9,"unit":"oz","pm":0.05,"stated":"WEIGHT: 13.4oz (14.9oz w/ barrel nut)","source":{"type":"spec","publisher":"retailer","name":"Aerospace Arms, Geissele Automatics 13.5\" Super Modular Rail MK16 M-LOK - Black (05-650B), Features and Specifications","url":"https://aerospacearms.com/geissele-automatics-13-5-super-modular-rail-mk16-m-lok-black/","retrieved":"2026-10-06","via":"harvest"}},{"id":"aerospace-arms-ddc","value":14.9,"unit":"oz","pm":0.05,"stated":"WEIGHT: 13.4oz (14.9oz w/ barrel nut)","source":{"type":"spec","publisher":"retailer","name":"Aerospace Arms, Geissele Automatics 13.5\" Super Modular Rail MK16 M-LOK - DDC (05-650S), Features and Specifications","url":"https://aerospacearms.com/geissele-automatics-13-5-super-modular-rail-mk16-m-lok-ddc/","retrieved":"2026-10-06","via":"harvest"}},{"id":"brownells","value":14.9,"unit":"oz","pm":0.05,"stated":"13.5\" WEIGHT: 13.4oz (14.9oz w/ barrel nut)","source":{"type":"spec","publisher":"retailer","name":"Brownells, GEISSELE AUTOMATICS LLC AR-15 MK16 SUPER MODULAR RAILS M-LOK, Specs (one page for the four lengths, a weight for each)","url":"https://www.brownells.com/gun-parts/rifle-parts/rifle-handguards-parts/ar-15-mk16-super-modular-rails-m-lok/","retrieved":"2026-10-06","via":"harvest"}},{"id":"mister-guns","value":14.9,"unit":"oz","pm":0.05,"stated":"13.4 oz. weight (14.9 oz. w/ barrel nut)","source":{"type":"spec","publisher":"retailer","name":"Mister Guns, Geissele Automatics Super Modular Rail MK16 13.5\" M-LOK Desert - 05-650S, description","url":"https://shop.misterguns.com/product/14213/geissele-automatics-super-modular-rail-mk16-13-5-m-lok-desert-05-650s","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"aerospace-arms","reason":"Four pages of three sellers state the one figure with the barrel nut; none states another."},"note":"Every page read that gives a weight for this length gives the one pair, for both colours: 13.4 oz alone and 14.9 oz with its barrel nut. The barrel nut is what it mounts by and comes with it; a build weighs the pair's second figure. The maker's own page isn't opened."},"weight_handguard":{"label":"Weight, the handguard alone","kind":"mass","measurements":[{"id":"aerospace-arms","value":13.4,"unit":"oz","pm":0.05,"stated":"WEIGHT: 13.4oz (14.9oz w/ barrel nut)","source":{"type":"spec","publisher":"retailer","name":"Aerospace Arms, Geissele Automatics 13.5\" Super Modular Rail MK16 M-LOK - Black (05-650B), Features and Specifications","url":"https://aerospacearms.com/geissele-automatics-13-5-super-modular-rail-mk16-m-lok-black/","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":13.4,"unit":"oz","pm":0.05,"stated":"Weight 13.4 oz.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics MK16 Free Float AR-15 Handguard - M-LOK - 13.5\" (05-650B), specifications","url":"https://www.primaryarms.com/geissele-automatics-mk16-super-modular-m-lok-rail-black-13.5","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms-ddc","value":13.4,"unit":"oz","pm":0.05,"stated":"Weight 13.4 oz.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics MK16 Free Float AR-15 Handguard - M-LOK - 13.5\" (05-650S, Desert Dirt Color), specifications","url":"https://www.primaryarms.com/geissele-automatics-13.5-in-super-modular-rail-m-lok-ddc","retrieved":"2026-10-06","via":"harvest"}},{"id":"brownells","value":13.4,"unit":"oz","pm":0.05,"stated":"13.5\" WEIGHT: 13.4oz (14.9oz w/ barrel nut)","source":{"type":"spec","publisher":"retailer","name":"Brownells, GEISSELE AUTOMATICS LLC AR-15 MK16 SUPER MODULAR RAILS M-LOK, Specs (one page for the four lengths, a weight for each)","url":"https://www.brownells.com/gun-parts/rifle-parts/rifle-handguards-parts/ar-15-mk16-super-modular-rails-m-lok/","retrieved":"2026-10-06","via":"harvest"}},{"id":"mister-guns","value":13.4,"unit":"oz","pm":0.05,"stated":"13.4 oz. weight (14.9 oz. w/ barrel nut)","source":{"type":"spec","publisher":"retailer","name":"Mister Guns, Geissele Automatics Super Modular Rail MK16 13.5\" M-LOK Desert - 05-650S, description","url":"https://shop.misterguns.com/product/14213/geissele-automatics-super-modular-rail-mk16-13-5-m-lok-desert-05-650s","retrieved":"2026-10-06","via":"harvest"}},{"id":"tlo","value":13.4,"unit":"oz","pm":0.05,"stated":"Weight: 13.4 oz","source":{"type":"spec","publisher":"retailer","name":"TLO Outdoors, Geissele Automatics SMR MK16 13.5in M-LOK Free-Float Handguard Rail, Black 05-650B, Specs","url":"https://tlooutdoors.com/products/geissele-automatics-smr-mk16-13-5in-m-lok-free-float-handguard-rail-black-05-650b","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"aerospace-arms","reason":"Six pages of five sellers state the one figure. The model's metal as aluminium weighs within a few percent of it (the part's approximations say what)."},"note":"The same pair's first figure. Primary Arms and TLO Outdoors give it alone."},"length":{"label":"Length, end to end (its rear face to its muzzle end, the tabs behind the rear face left out)","kind":"length","measurements":[{"id":"aerospace-arms","value":13.5,"unit":"in","pm":0.05,"stated":"LENGTH: 13.5\"","source":{"type":"spec","publisher":"retailer","name":"Aerospace Arms, Geissele Automatics 13.5\" Super Modular Rail MK16 M-LOK - Black (05-650B), Features and Specifications","url":"https://aerospacearms.com/geissele-automatics-13-5-super-modular-rail-mk16-m-lok-black/","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":13.5,"unit":"in","pm":0.05,"stated":"Handguard Length 13.5","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics MK16 Free Float AR-15 Handguard - M-LOK - 13.5\" (05-650B), specifications","url":"https://www.primaryarms.com/geissele-automatics-mk16-super-modular-m-lok-rail-black-13.5","retrieved":"2026-10-06","via":"harvest"}},{"id":"tlo","value":13.5,"unit":"in","pm":0.05,"stated":"Length: 13.5 in","source":{"type":"spec","publisher":"retailer","name":"TLO Outdoors, Geissele Automatics SMR MK16 13.5in M-LOK Free-Float Handguard Rail, Black 05-650B, Specs","url":"https://tlooutdoors.com/products/geissele-automatics-smr-mk16-13-5in-m-lok-free-float-handguard-rail-black-05-650b","retrieved":"2026-10-06","via":"harvest"}},{"id":"photo","value":13.52,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/geissele-mk16-135-handguard e4af6c8f0204 (Primary Arms' gallery for 05-650B, 05-650B_03.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own top rail's 32 slots at the Picatinny pitch (std.picatinny.slot_pitch): a quadratic fit of their centres, 55.83 px a pitch at the muzzle end and 56.63 at the rear","method":"the rail's front end (px 105, its near edge: true column 118.0) to its rear end (px 2058: true column 2047.1): rail coordinates -1.74 and 32.57, 34.31 pitches; the lens stood over column 1170 and 34.3 in from the rifle's middle plane (the rail's notches narrow from 30.8 px there to 6.5 at the muzzle end and 10.6 at the rear, as its two edges part), so what stands z nearer the lens reads large about that column by 34.3 / (34.3 - z): 1.0237 on the side face, 1.0124 at the rail's near edge (scratch/m2.py)","via":"harvest"}}],"adopt":{"from":"photo","reason":"Its own rail's 32 slots and two end lands count 13.52 in, which is what the model's rail and slots add up to; the sellers' 13.5 in agrees within its last digit."},"note":"The sellers' 13.5 in, and by its own rail it is that: 32 slots and a land at each end, 13.52 in. Its rail runs the whole length: on the level photo the rail's rear end and the body's rear face are one plane within 0.01 in once each is read at its own depth, and the rail's nose and the side faces' tips at the muzzle end within 0.02."},"width":{"label":"Width across the side faces (3 to 9 o'clock)","kind":"length","measurements":[{"id":"aerospace-arms","value":1.59,"unit":"in","pm":0.005,"stated":"OUTER DIAMETER (DAQ*): 1.59\" [...] *DAQ - Distance Across Quadrants","source":{"type":"spec","publisher":"retailer","name":"Aerospace Arms, Geissele Automatics 13.5\" Super Modular Rail MK16 M-LOK - Black (05-650B), Features and Specifications","url":"https://aerospacearms.com/geissele-automatics-13-5-super-modular-rail-mk16-m-lok-black/","retrieved":"2026-10-06","via":"harvest"}},{"id":"brownells","value":1.59,"unit":"in","pm":0.005,"stated":"OUTER DIAMETER (DAQ*): 1.59\"","source":{"type":"spec","publisher":"retailer","name":"Brownells, GEISSELE AUTOMATICS LLC AR-15 MK16 SUPER MODULAR RAILS M-LOK, Specs (one page for the four lengths, a weight for each)","url":"https://www.brownells.com/gun-parts/rifle-parts/rifle-handguards-parts/ar-15-mk16-super-modular-rails-m-lok/","retrieved":"2026-10-06","via":"harvest"}},{"id":"tlo","value":1.59,"unit":"in","pm":0.005,"stated":"Outer Diameter: 1.59 in","source":{"type":"spec","publisher":"retailer","name":"TLO Outdoors, Geissele Automatics SMR MK16 13.5in M-LOK Free-Float Handguard Rail, Black 05-650B, Specs","url":"https://tlooutdoors.com/products/geissele-automatics-smr-mk16-13-5in-m-lok-free-float-handguard-rail-black-05-650b","retrieved":"2026-10-06","via":"harvest"}},{"id":"mister-guns","value":1.59,"unit":"in","pm":0.005,"stated":"1.26”/1.59” inner/outer diameter","source":{"type":"spec","publisher":"retailer","name":"Mister Guns, Geissele Automatics Super Modular Rail MK16 13.5\" M-LOK Desert - 05-650S, description","url":"https://shop.misterguns.com/product/14213/geissele-automatics-super-modular-rail-mk16-13-5-m-lok-desert-05-650s","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"aerospace-arms","reason":"Four sellers state the one figure."},"note":"The sellers' \"OUTER DIAMETER (DAQ*)\" with \"*DAQ - Distance Across Quadrants\": the distance across two opposite faces that carry M-LOK slots. It is the scale of the two views of its muzzle end."},"height":{"label":"Height (the rail's top to the bottom of the clamp block at its rear end)","kind":"length","measurements":[{"id":"aerospace-arms","value":2.39,"unit":"in","pm":0.005,"stated":"HEIGHT: 2.39\"","source":{"type":"spec","publisher":"retailer","name":"Aerospace Arms, Geissele Automatics 13.5\" Super Modular Rail MK16 M-LOK - Black (05-650B), Features and Specifications","url":"https://aerospacearms.com/geissele-automatics-13-5-super-modular-rail-mk16-m-lok-black/","retrieved":"2026-10-06","via":"harvest"}},{"id":"brownells","value":2.39,"unit":"in","pm":0.005,"stated":"HEIGHT: 2.39\"","source":{"type":"spec","publisher":"retailer","name":"Brownells, GEISSELE AUTOMATICS LLC AR-15 MK16 SUPER MODULAR RAILS M-LOK, Specs (one page for the four lengths, a weight for each)","url":"https://www.brownells.com/gun-parts/rifle-parts/rifle-handguards-parts/ar-15-mk16-super-modular-rails-m-lok/","retrieved":"2026-10-06","via":"harvest"}},{"id":"tlo","value":2.39,"unit":"in","pm":0.005,"stated":"Height: 2.39 in","source":{"type":"spec","publisher":"retailer","name":"TLO Outdoors, Geissele Automatics SMR MK16 13.5in M-LOK Free-Float Handguard Rail, Black 05-650B, Specs","url":"https://tlooutdoors.com/products/geissele-automatics-smr-mk16-13-5in-m-lok-free-float-handguard-rail-black-05-650b","retrieved":"2026-10-06","via":"harvest"}},{"id":"mister-guns","value":2.39,"unit":"in","pm":0.005,"stated":"2.39” height","source":{"type":"spec","publisher":"retailer","name":"Mister Guns, Geissele Automatics Super Modular Rail MK16 13.5\" M-LOK Desert - 05-650S, description","url":"https://shop.misterguns.com/product/14213/geissele-automatics-super-modular-rail-mk16-13-5-m-lok-desert-05-650s","retrieved":"2026-10-06","via":"harvest"}},{"id":"photo","value":2.41,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-mk16-135-handguard e4af6c8f0204 (Primary Arms' gallery for 05-650B, 05-650B_03.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own rail's slots at the rear end (56.6 px a pitch, 143.7 px/in on the middle plane; 145.4 at the rail's near edge and 147.1 on the side face)","method":"the rail's tooth tops (row 559.3) to the clamp block's bottom edge (row 911) at columns 1964 to 2004: 351.7 px, each half read at its own depth about the image's middle row (scratch/m2.py)","via":"harvest"}}],"adopt":{"from":"aerospace-arms","reason":"Four sellers state the one figure; the level photo reads it within 1% as the rail's top to the clamp block's bottom."},"note":"What the sellers' 2.39 in spans is read on the level photo, as on the 15 in rail's: the rail's top to the bottom of the clamp block under the rear end."},"inside_diameter":{"label":"Inside diameter","kind":"length","measurements":[{"id":"aerospace-arms","value":1.26,"unit":"in","pm":0.005,"stated":"INNER DIAMETER: 1.26\"","source":{"type":"spec","publisher":"retailer","name":"Aerospace Arms, Geissele Automatics 13.5\" Super Modular Rail MK16 M-LOK - Black (05-650B), Features and Specifications","url":"https://aerospacearms.com/geissele-automatics-13-5-super-modular-rail-mk16-m-lok-black/","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms-ddc","value":1.26,"unit":"in","pm":0.005,"stated":"Inner Diameter 1.26 in.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics MK16 Free Float AR-15 Handguard - M-LOK - 13.5\" (05-650S, Desert Dirt Color), specifications","url":"https://www.primaryarms.com/geissele-automatics-13.5-in-super-modular-rail-m-lok-ddc","retrieved":"2026-10-06","via":"harvest"}},{"id":"brownells","value":1.26,"unit":"in","pm":0.005,"stated":"INNER DIAMETER: 1.26\"","source":{"type":"spec","publisher":"retailer","name":"Brownells, GEISSELE AUTOMATICS LLC AR-15 MK16 SUPER MODULAR RAILS M-LOK, Specs (one page for the four lengths, a weight for each)","url":"https://www.brownells.com/gun-parts/rifle-parts/rifle-handguards-parts/ar-15-mk16-super-modular-rails-m-lok/","retrieved":"2026-10-06","via":"harvest"}},{"id":"tlo","value":1.26,"unit":"in","pm":0.005,"stated":"Inner Diameter: 1.26 in","source":{"type":"spec","publisher":"retailer","name":"TLO Outdoors, Geissele Automatics SMR MK16 13.5in M-LOK Free-Float Handguard Rail, Black 05-650B, Specs","url":"https://tlooutdoors.com/products/geissele-automatics-smr-mk16-13-5in-m-lok-free-float-handguard-rail-black-05-650b","retrieved":"2026-10-06","via":"harvest"}},{"id":"mister-guns","value":1.26,"unit":"in","pm":0.005,"stated":"1.26”/1.59” inner/outer diameter","source":{"type":"spec","publisher":"retailer","name":"Mister Guns, Geissele Automatics Super Modular Rail MK16 13.5\" M-LOK Desert - 05-650S, description","url":"https://shop.misterguns.com/product/14213/geissele-automatics-super-modular-rail-mk16-13-5-m-lok-desert-05-650s","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":1.35,"unit":"in","pm":0.005,"stated":"Inner Diameter 1.35 in.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics MK16 Free Float AR-15 Handguard - M-LOK - 13.5\" (05-650B), specifications","url":"https://www.primaryarms.com/geissele-automatics-mk16-super-modular-m-lok-rail-black-13.5","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"aerospace-arms","reason":"Five pages state 1.26 in, Primary Arms' own page for the other colour among them; its page for the black rail is alone with 1.35, and a wall of 0.12 in is not what the view of the muzzle end shows."},"note":"Sellers' \"INNER DIAMETER\". Primary Arms' page for the black rail says 1.35 in, against 1.26 on its own page for the same rail in Desert Dirt Color and on every other page read: kept here, and not adopted. The model takes 1.26 as the circle its flat inner walls touch (the view of the muzzle end shows the side and lower walls 0.17 in thick: 1.59 less 1.26, halved, is 0.165)."},"rear_face_x":{"label":"Its rear face against the receiver's front face (negative: behind it)","kind":"length","measurements":[{"id":"derived","value":-0.445,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"0in - {std.ar15.upper_barrel_thread_length}","via":"harvest"}}],"note":"No page read says where it stops, and no photo of it mounted is on file. As the 15 in rail: it slides back over its barrel nut, and its rear face is taken to meet the receiver's front shoulder, where the barrel-nut thread begins (std.ar15.upper_barrel_thread_length behind the front face), with no gap. A check: its rail's first slot then stands 0.01 in from where the receiver's own row of slots would continue (bcm-m4-upper: 13 slots from 1.31 in at the standard's pitch)."},"tab_length":{"label":"Its lower tabs' reach behind its rear face","kind":"length","measurements":[{"id":"derived","value":0.26,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.tab_length}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws). On this length's level photo the lower tab's end (px 2104) stands 0.25 in behind the rear face's edge (px 2068) at the side face's scale."},"rear_x":{"label":"The outline's rear end (its lower tabs' ends) against the receiver's front face (negative: behind it)","kind":"length","measurements":[{"id":"derived","value":-0.705,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{.rear_face_x} - {.tab_length}","via":"harvest"}}]},"overall_length":{"label":"Length over all, its lower tabs' ends to its muzzle end","kind":"length","measurements":[{"id":"derived","value":13.78,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{.length} + {.tab_length}","via":"harvest"}}]},"tab_top_below_bore":{"label":"Its lower tabs' top edge below the bore axis","kind":"length","measurements":[{"id":"derived","value":0.27,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.tab_top_below_bore}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws). Rows 777 to 832 on this length's level photo, the 15 in rail's within 0.03."},"tab_bottom_below_bore":{"label":"Its lower tabs' bottom edge below the bore axis","kind":"length","measurements":[{"id":"derived","value":0.64,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.tab_bottom_below_bore}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws)."},"tab_screw_d":{"label":"A tab's set screw, its diameter as it shows from the side","kind":"length","measurements":[{"id":"derived","value":0.14,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.tab_screw_d}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws). The screw's round end is 18 px across at px (2090, 815) on this length's level photo."},"tongue_length":{"label":"Its upper tabs' reach behind its rear face","kind":"length","measurements":[{"id":"derived","value":0.12,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.tongue_length}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws). This length's level photo reads 0.10 (px 2068 to 2082)."},"upper_tab_gap":{"label":"The opening between its two upper tabs","kind":"length","measurements":[{"id":"derived","value":0.638,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"2 * {bcm-m4-upper.side_half_width}","via":"harvest"}}],"note":"As the 15 in rail's: not measured (no view shows it square on); the tabs stand beside a mil-spec receiver's flat sides under its rail and are drawn against those flats with no clearance. Aerospace Arms: \"These handguards are designed to work with Mil-Spec M4 upper receivers. The compatibility with billet receiver sets is unknown.\""},"tongue_bottom_above_bore":{"label":"Its upper tabs' bottom edge above the bore axis","kind":"length","measurements":[{"id":"derived","value":0.545,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.tongue_bottom_above_bore}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws)."},"tongue_top_above_bore":{"label":"Its upper tabs' top edge above the bore axis","kind":"length","measurements":[{"id":"derived","value":0.727,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.tongue_top_above_bore}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws)."},"rail_top_above_bore":{"label":"Its rail's top above the bore axis","kind":"length","measurements":[{"id":"derived","value":1.2,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.rail_top_above_bore}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws). This length's level photo reads the rail's tooth tops 1.22 in above the middle of the side rows' slots (rows 560 and 739 at the muzzle end, 146 px/in), from a little above."},"body_bottom_below_bore":{"label":"The tube's bottom flat below the bore axis","kind":"length","measurements":[{"id":"derived","value":0.86,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.body_bottom_below_bore}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws). The view of this length's muzzle end reads the bottom flat 0.86 in below the middle of the side faces (274.5 px at 319 px/in up and down)."},"side_flat_height":{"label":"The side faces' height (crease to crease)","kind":"length","measurements":[{"id":"derived","value":0.6,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.side_flat_height}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws). The view of this length's muzzle end reads 0.61 (the side faces' creases at rows 880 and 1075, 319 px/in up and down)."},"upper_face_angle":{"label":"The faces between the sides and the rail: where their normal points, about the bore from the top (12 o'clock) toward the side","kind":"angle","measurements":[{"id":"end-view","value":45,"unit":"deg","pm":2,"source":{"type":"photo","photo":"references/geissele-mk16-135-handguard a4374faf412e (Aerospace Arms' gallery for the 13.5 in rail in Desert Dirt Color, mk16-ddc-135-03-wide: its muzzle end seen from ahead and about 12.6° above the bore, 3906 x 1464)","scaleRef":"the view's own geometry: across the rifle it is true; up and down it is shortened by the cosine of the lens's height above the bore, 0.976 (the underside's slots, 40 mm apart, show 112 px apart where an inch across is 327 px: 12.6°)","method":"the muzzle face's upper left arm, its outer edge from the side face's crease (px 1680, 880) to where it turns up into the neck (px 1808, 758): 128 px across, 122 up, 125 once the shortening is taken out: 44.4°; its upper stretch alone reads 45.4° (scratch/g_end_ddc_ul.png)","via":"harvest"}}],"note":"The 15 in rail's ledger takes these faces at 45° for want of a view square on an end; this length has one, and they are at 45°."},"lower_face_angle":{"label":"The faces between the sides and the bottom: where their normal points, about the bore from the top (12 o'clock) toward the side","kind":"angle","measurements":[{"id":"end-view","value":131.4,"unit":"deg","pm":1,"source":{"type":"photo","photo":"references/geissele-mk16-135-handguard a4374faf412e (Aerospace Arms' gallery for the 13.5 in rail in Desert Dirt Color, mk16-ddc-135-03-wide: its muzzle end seen from ahead and about 12.6° above the bore, 3906 x 1464)","scaleRef":"the view's own geometry: across the rifle true, up and down shortened by 0.976 (upper_face_angle's scaleRef)","method":"the muzzle face's lower outline, which is the silhouette there: its left edge from px (1688, 1084) to (1829, 1240) and its right from (2193, 1084) to (2051, 1240), 0.904 and 0.910 px across for each px down: 47.6° from the horizontal as it shows, 48.6° with the shortening taken out (scratch/m3.py)","via":"harvest"}},{"id":"end-view-black","value":131.5,"unit":"deg","pm":1,"source":{"type":"photo","photo":"references/geissele-mk16-135-handguard 7ad0c578cf97 (Aerospace Arms' gallery for the 13.5 in black rail, mk16-blk-135-03-wide: its muzzle end seen from ahead and above, 3906 x 1464)","scaleRef":"the same","method":"the same edges on the black rail: px (1624, 1194) to (1777, 1362) and (2177, 1194) to (2023, 1362), 0.911 and 0.917 across for each px down: 48.5° (scratch/m3.py)","via":"harvest"}}],"adopt":{"from":"end-view","reason":"Two photos of two rails of this length agree within 0.1°; the Desert Dirt one shows its edges better."},"note":"Not 135°: the lower faces stand steeper than the upper ones, 48.6° from the horizontal, in both views of this length's muzzle end, and no height of lens could make a face at 45° read steeper than 45° (a lens above the bore shortens what stands up and down). The 15 in rail's ledger takes them at 45° for want of an end view; its bottom flat is the narrower for it (0.47 in against this length's 0.61)."},"upper_face_distance":{"label":"The upper faces' distance from the bore axis, along their normal","kind":"length","measurements":[{"id":"derived","value":0.774282,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{.width} / 2 * sin({.upper_face_angle}) + {.side_flat_height} / 2 * cos({.upper_face_angle})","via":"harvest"}}],"note":"Through the side faces' upper creases at the faces' angle."},"lower_face_distance":{"label":"The lower faces' distance from the bore axis, along their normal","kind":"length","measurements":[{"id":"derived","value":0.794732,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{.width} / 2 * sin({.lower_face_angle}) - {.side_flat_height} / 2 * cos({.lower_face_angle})","via":"harvest"}}],"note":"Through the side faces' lower creases at the faces' angle. As far as the side faces' own: the inside's 1.26 in circle leaves the lower walls as thick as the side walls, which is what the view of the muzzle end shows (0.17 in)."},"bottom_flat_width":{"label":"The bottom flat's width","kind":"length","measurements":[{"id":"end-view","value":0.61,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-mk16-135-handguard a4374faf412e (Aerospace Arms' gallery for the 13.5 in rail in Desert Dirt Color, mk16-ddc-135-03-wide: its muzzle end seen from ahead and about 12.6° above the bore, 3906 x 1464)","scaleRef":"its width across the side faces (this ledger's width) over 520 px: 327 px/in across","method":"the muzzle face's bottom edge between the two lower faces' fitted lines at the bottom's row (px 1840 and 2040 at row 1252): 200 px (scratch/m3.py)","via":"harvest"}},{"id":"end-view-black","value":0.61,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-mk16-135-handguard 7ad0c578cf97 (Aerospace Arms' gallery for the 13.5 in black rail, mk16-blk-135-03-wide: its muzzle end seen from ahead and above, 3906 x 1464)","scaleRef":"its width across the side faces over 580 px: 364.8 px/in across","method":"the same on the black rail: px 1788 and 2012 at row 1374, 224 px (scratch/m3.py)","via":"harvest"}}],"adopt":{"from":"end-view","reason":"The two photos read the same."},"note":"A check on lower_face_angle, not what the model draws from: lower faces at that angle from the side faces' creases down to the bottom leave a flat of 0.60 in."},"neck_base_above_bore":{"label":"Where the upper faces end and the neck under the rail begins, above the bore","kind":"length","measurements":[{"id":"derived","value":0.695,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.neck_base_above_bore}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws). The view of this length's muzzle end reads 0.69 (the upper face's turn into the neck at row 758, the bore at 977.5)."},"neck_chamfer_height":{"label":"The slope between the upper faces and the neck's walls, its height","kind":"length","measurements":[{"id":"derived","value":0.08,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.neck_chamfer_height}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws)."},"neck_width":{"label":"The neck's width under the rail","kind":"length","measurements":[{"id":"derived","value":0.61,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.neck_width}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws). The view of this length's muzzle end reads 0.61 (the neck's outer walls at px 1840 and 2040, 327 px/in)."},"channel_width":{"label":"The channel under the rail (the gas tube's), its width","kind":"length","measurements":[{"id":"derived","value":0.47,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.channel_width}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws). The view of this length's muzzle end reads 0.45 (the opening under the rail from px 1862 to 2010)."},"channel_roof_below_top":{"label":"The channel's roof below the rail's top","kind":"length","measurements":[{"id":"derived","value":0.18,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.channel_roof_below_top}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws)."},"trough_width":{"label":"The troughs along the inside of the bottom, the side faces and the upper faces: their width","kind":"length","measurements":[{"id":"end-view","value":0.49,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-mk16-135-handguard a4374faf412e (Aerospace Arms' gallery for the 13.5 in rail in Desert Dirt Color, mk16-ddc-135-03-wide: its muzzle end seen from ahead and about 12.6° above the bore, 3906 x 1464)","scaleRef":"its width across the side faces (this ledger's width) over 520 px: 327 px/in across","method":"the notch in the muzzle face's inner edge at the bottom, its two upright sides at px 1862 and 2022: 160 px on a 3x gridded crop (scratch/g_end_ddc_low.png)","via":"harvest"}},{"id":"end-view-side","value":0.48,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-mk16-135-handguard a4374faf412e (Aerospace Arms' gallery for the 13.5 in rail in Desert Dirt Color, mk16-ddc-135-03-wide: its muzzle end seen from ahead and about 12.6° above the bore, 3906 x 1464)","scaleRef":"its width across the side faces over 520 px, up and down shortened by 0.976: 319 px/in","method":"the left side wall's thin stretch at the muzzle face, rows 905 to 1058: 153 px (scratch/g_end_ddc_low.png)","via":"harvest"}}],"adopt":{"from":"end-view","reason":"The bottom's shows both its steps; the side wall's agrees within 0.01 in."},"note":"Inside, the walls are not one thickness: a flat-floored trough runs along the bottom's middle, with a step up at each side to the lower walls, and the underside's M-LOK slots are in its floor; the side walls' ends at the muzzle face are as thin over the same height, with a step where a side wall meets a lower one (Aerospace Arms' view from ahead and beside, 1b4421f8bedc); the upper walls' ends look as thin (0.09 to 0.10 in on a 5x crop, scratch/g_end_ddc_ul.png), and are drawn so at the bottom's width, which isn't read there; the lower walls' ends are about 0.15 in thick, and are drawn whole. Seen at the muzzle end; taken to run the length of the flat-walled inside."},"trough_wall":{"label":"The wall a trough's floor leaves, its thickness","kind":"length","measurements":[{"id":"end-view","value":0.094,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-mk16-135-handguard a4374faf412e (Aerospace Arms' gallery for the 13.5 in rail in Desert Dirt Color, mk16-ddc-135-03-wide: its muzzle end seen from ahead and about 12.6° above the bore, 3906 x 1464)","scaleRef":"its width across the side faces over 520 px, up and down shortened by 0.976: 319 px/in","method":"the muzzle face's bottom band at its middle, from the trough's floor (row 1222) to the bottom edge (row 1252): 30 px on a 3x gridded crop (scratch/g_end_ddc_low.png)","via":"harvest"}},{"id":"end-view-side","value":0.098,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-mk16-135-handguard a4374faf412e (Aerospace Arms' gallery for the 13.5 in rail in Desert Dirt Color, mk16-ddc-135-03-wide: its muzzle end seen from ahead and about 12.6° above the bore, 3906 x 1464)","scaleRef":"its width across the side faces over 520 px: 327 px/in across","method":"the left side wall's end at the muzzle face, px 1680 to 1712: 32 px (scratch/g_end_ddc_low.png)","via":"harvest"}}],"adopt":{"from":"end-view","reason":"Read where the trough's two steps show; the side wall's end is the same within a pixel."}},"rail_slots":{"label":"Slots in its top rail","kind":"count","measurements":[{"id":"photo","value":32,"unit":"count","source":{"type":"photo","photo":"references/geissele-mk16-135-handguard e4af6c8f0204 (Primary Arms' gallery for 05-650B, 05-650B_03.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"none: a count","method":"the notches between the teeth along the top edge: 32, centres from px 214.8 to px 1958.2, each 54.8 to 57.2 px from the next with none missing; a longer tooth at each end (scratch/m2.py). Aerospace Arms' photo of its right side (6ab964c18436) has 29 notches in its silhouette and three more teeth ahead of them where its lens looks down on the rail: 32","via":"harvest"}}]},"rail_slot0_from_rear":{"label":"Its rail's rearmost slot (its centre) ahead of its rear face","kind":"length","measurements":[{"id":"photo","value":0.62,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-mk16-135-handguard e4af6c8f0204 (Primary Arms' gallery for 05-650B, 05-650B_03.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own top rail's 32 slots at the Picatinny pitch (std.picatinny.slot_pitch): a quadratic fit of their centres, 55.83 px a pitch at the muzzle end and 56.63 at the rear","method":"the rail's rear end (px 2058, its near edge: true column 2047.1, rail coordinate 32.57) behind the rearmost slot's centre (px 1958.2, coordinate 31): 1.57 pitches; the body's rear face (px 2068 on the side face: true column 2047.2) is the same plane (scratch/m2.py)","via":"harvest"}}]},"rail_slot0_x":{"label":"Its rail's rearmost slot (its centre) ahead of the receiver's front face","kind":"length","measurements":[{"id":"derived","value":0.175,"unit":"in","pm":0.045,"source":{"type":"derived","expr":"{.rear_face_x} + {.rail_slot0_from_rear}","via":"harvest"}}]},"rail_front_from_last_slot":{"label":"Its rail's front end ahead of its last slot's centre","kind":"length","measurements":[{"id":"photo","value":0.685,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-mk16-135-handguard e4af6c8f0204 (Primary Arms' gallery for 05-650B, 05-650B_03.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own top rail's 32 slots at the Picatinny pitch (std.picatinny.slot_pitch): a quadratic fit of their centres, 55.83 px a pitch at the muzzle end and 56.63 at the rear","method":"the rail's front end (px 105, its near edge: true column 118.0, rail coordinate -1.74) ahead of the frontmost slot's centre (px 214.8, coordinate 0): 1.74 pitches; the side faces' tips (px 95 on the side face: true column 119.9) are the same plane within 0.02 in (scratch/m2.py)","via":"harvest"}}],"note":"The rail's last tooth runs to the muzzle end and is sloped off at its top (rail_nose_length)."},"rail_nose_length":{"label":"The slope at the rail's front end, its length along the rail","kind":"length","measurements":[{"id":"photo","value":0.29,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-mk16-135-handguard e4af6c8f0204 (Primary Arms' gallery for 05-650B, 05-650B_03.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own rail's slots at the muzzle end, at the rail's near edge: 143.5 px/in","method":"the top edge leaves the tooth tops' level (row 560.2) at px 147 and reaches the front end at px 105: 42 px (scratch/m2.py)","via":"harvest"}}],"note":"The rail's top is sloped down to the muzzle end over its last quarter inch: a face of its own in Aerospace Arms' views from ahead (638b5d051a67, a4374faf412e)."},"rail_nose_drop":{"label":"The slope at the rail's front end, how far its front edge is below the rail's top","kind":"length","measurements":[{"id":"photo","value":0.11,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-mk16-135-handguard e4af6c8f0204 (Primary Arms' gallery for 05-650B, 05-650B_03.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own rail's slots at the muzzle end, at the rail's near edge: 143.5 px/in","method":"the top edge at the front end (row 575.5 at px 107) below the tooth tops (row 560.2): 15.3 px, a pixel more at the very end (scratch/m2.py)","via":"harvest"}}]},"mlok_side_slots":{"label":"M-LOK slots on each side face (3 and 9 o'clock)","kind":"count","measurements":[{"id":"photo","value":7,"unit":"count","source":{"type":"photo","photo":"references/geissele-mk16-135-handguard e4af6c8f0204 (Primary Arms' gallery for 05-650B, 05-650B_03.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"none: a count","method":"the middle row's slots, light showing through each: seven, 217 to 230 px apart (scratch/m2.py); seven on the right side in Aerospace Arms' photo of it (6ab964c18436) and seven on the left in its photo of that side (9ab6181ab578)","via":"harvest"}}]},"mlok_lower_slots":{"label":"M-LOK slots on each lower face (between the sides and the bottom)","kind":"count","measurements":[{"id":"photo","value":7,"unit":"count","source":{"type":"photo","photo":"references/geissele-mk16-135-handguard e4af6c8f0204 (Primary Arms' gallery for 05-650B, 05-650B_03.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"none: a count","method":"the lower row's slots, light showing through each: seven, their ends within 0.02 in of the side row's (rail coordinates -0.54 to 23.25 against -0.40 to 23.25 for their front ends) (scratch/m2.py); seven on each side in Aerospace Arms' two side photos","via":"harvest"}}]},"mlok_upper_slots":{"label":"M-LOK slots on each upper face (between the sides and the rail)","kind":"count","measurements":[{"id":"photo","value":6,"unit":"count","source":{"type":"photo","photo":"references/geissele-mk16-135-handguard e4af6c8f0204 (Primary Arms' gallery for 05-650B, 05-650B_03.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"none: a count","method":"the upper row's slots, light showing through each: six, each over one of the side row's front six (their rear ends at rail coordinates 2.04, 6.10, 10.15, 14.19 against the side row's 1.93, 6.04, 10.15, 14.23); six on each side in Aerospace Arms' two side photos (6ab964c18436, 9ab6181ab578)","via":"harvest"}}],"note":"One fewer than the side faces: where the rearmost would be, the upper face carries a sling swivel socket."},"mlok_bottom_slots":{"label":"M-LOK slots on its underside (6 o'clock)","kind":"count","measurements":[{"id":"derived","value":7,"unit":"count","source":{"type":"derived","expr":"{.mlok_side_slots}","via":"harvest"}}],"note":"The row is the sellers' sentence (\"M-LOK slots on every quadrant\", Aerospace Arms; \"seven sides of M-LOK\", Primary Arms) and, on this length, a photo's: Aerospace Arms' views into the muzzle end (a4374faf412e, 7ad0c578cf97) show the underside's foremost four slots from inside, in the trough's floor, at the side rows' pitch (112 px apart where 40 mm at that lens's height is 112) and with the foremost as far from the muzzle end as the side rows' (0.35 in against 0.34). How far back the row runs isn't seen: it is taken to have the side rows' seven, which is what fits ahead of the clamp block (mlok_bottom_slot0_x). Four are counted; seven is an assumption, not a count."},"mlok_bottom_slot0_x":{"label":"The underside's rearmost M-LOK slot (its centre) ahead of the receiver's front face","kind":"length","measurements":[{"id":"derived","value":2.655,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{.mlok_side_slot0_x}","via":"harvest"}}],"note":"Taken at the side rows' stations: the foremost four are seen there from inside the muzzle end (mlok_bottom_slots), the rear ones aren't seen. The clamp block and its split take the rear of the bottom; the side rows' rearmost slot begins 2.47 in ahead of the rear face, 0.1 in ahead of where the block's front ramp ends on the level photo (2.36), so the row can start there with all seven ahead of the block. An assumption for the rear three."},"mlok_side_slot0_from_rear":{"label":"The side faces' rearmost M-LOK slot (its centre) ahead of the rear face","kind":"length","measurements":[{"id":"photo","value":3.1,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-mk16-135-handguard e4af6c8f0204 (Primary Arms' gallery for 05-650B, 05-650B_03.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own top rail's 32 slots at the Picatinny pitch (std.picatinny.slot_pitch): a quadratic fit of their centres, 55.83 px a pitch at the muzzle end and 56.63 at the rear; the lens stood over column 1170 and 34.3 in from the rifle's middle plane (the rail's notches narrow from 30.8 px there to 6.5 at the muzzle end and 10.6 at the rear, as its two edges part), so what stands z nearer the lens reads large about that column by 34.3 / (34.3 - z): 1.0237 on the side face, 1.0124 at the rail's near edge","method":"the side row's slots' own edges where they bound the light (the rear ends of the four ahead of the lens, the front ends of the two behind it), each brought to its true place: rail coordinates 2.283, 6.300, 10.309, 14.293 and 19.119, 23.105, 3.997 pitches apart within 0.02; the rearmost slot's rear end at 26.295 by both, 6.275 pitches (2.47 in) ahead of the rear face (32.57), its centre half a slot (std.mlok.slot_length) further (scratch/m2.py)","via":"harvest"}}],"note":"The 15 in rail's reads 3.08: the rows begin at the same place behind, and the shorter rail has one slot fewer ahead."},"mlok_side_slot0_x":{"label":"The side and lower faces' rearmost M-LOK slot (its centre) ahead of the receiver's front face","kind":"length","measurements":[{"id":"derived","value":2.655,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{.rear_face_x} + {.mlok_side_slot0_from_rear}","via":"harvest"}}]},"mlok_upper_slot0_x":{"label":"The upper faces' rearmost M-LOK slot (its centre) ahead of the receiver's front face","kind":"length","measurements":[{"id":"derived","value":4.229803,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{.mlok_side_slot0_x} + {std.mlok.slot_pitch}","via":"harvest"}}],"note":"One slot pitch ahead of the side faces' rearmost: the upper rows have the side rows' front six."},"mlok_upper_row_above_bore":{"label":"The upper rows of slots, their middle line above the bore","kind":"length","measurements":[{"id":"derived","value":0.51,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.mlok_upper_row_above_bore}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws). This length's level photo reads the upper row's slots 0.51 in above the side row's (rows 665 and 739 at 146 px/in)."},"mlok_lower_row_below_bore":{"label":"The lower rows of slots, their middle line below the bore","kind":"length","measurements":[{"id":"derived","value":0.565,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.mlok_lower_row_below_bore}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws)."},"reach_inside":{"label":"The room inside its faces, from a face in to the barrel (what an M-LOK accessory's nuts may take)","kind":"length","measurements":[],"note":"Not sourced: it depends on the barrel and gas block under it, other parts. Its side walls are 0.165 in by the sellers' two figures (1.59 across, 1.26 inside); the bottom's is 0.09 in the trough."},"socket_from_rear":{"label":"The sling swivel sockets (their centres) ahead of the rear face","kind":"length","measurements":[{"id":"derived","value":2.77,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.socket_from_rear}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws). This length's level photo has the cup's centre at px 1667, 2.75 in ahead of the rear face's edge at the upper face's scale."},"socket_above_bore":{"label":"The sling swivel sockets' centres above the bore","kind":"length","measurements":[{"id":"derived","value":0.585,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.socket_above_bore}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws)."},"socket_ring_d":{"label":"A sling swivel socket's cup, its outside diameter","kind":"length","measurements":[{"id":"derived","value":0.545,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.socket_ring_d}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws)."},"socket_hole_d":{"label":"A sling swivel socket's hole, its diameter","kind":"length","measurements":[{"id":"derived","value":0.31,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.socket_hole_d}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws)."},"cross_bolt_front_from_rear":{"label":"The front cross bolt (its centre) ahead of the rear face","kind":"length","measurements":[{"id":"derived","value":1.57,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.cross_bolt_front_from_rear}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws). This length's level photo has the plate's front hole at px (1838, 847): 1.575 in ahead of the rear face's edge (px 2068) at the side face's scale."},"cross_bolt_rear_from_rear":{"label":"The rear cross bolt (its centre) ahead of the rear face","kind":"length","measurements":[{"id":"derived","value":0.55,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.cross_bolt_rear_from_rear}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws). This length's level photo has the plate's rear hole at px (1987, 866): 0.555 in ahead of the rear face's edge."},"cross_bolt_front_below_bore":{"label":"The front cross bolt's centre below the bore","kind":"length","measurements":[{"id":"derived","value":0.745,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.cross_bolt_front_below_bore}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws)."},"cross_bolt_rear_below_bore":{"label":"The rear cross bolt's centre below the bore","kind":"length","measurements":[{"id":"derived","value":0.835,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.cross_bolt_rear_below_bore}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws)."},"cross_bolt_hole_d":{"label":"A cross bolt's threaded hole in the left side's plate, its diameter","kind":"length","measurements":[{"id":"derived","value":0.21,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.cross_bolt_hole_d}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws)."},"cross_bolt_head_d":{"label":"A cross bolt's Torx head on the right side, its diameter","kind":"length","measurements":[{"id":"derived","value":0.32,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.cross_bolt_head_d}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws). Aerospace Arms' photo of this length's right side (6ab964c18436) shows the two Torx heads in their counterbores, 1.0 in apart."},"cross_bolt_counterbore_d":{"label":"A cross bolt's counterbore on the right side, its diameter","kind":"length","measurements":[{"id":"derived","value":0.46,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.cross_bolt_counterbore_d}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws)."},"clamp_gap_width":{"label":"The clamp block's split along its underside, its width","kind":"length","measurements":[{"id":"derived","value":0.51,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.clamp_gap_width}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws)."},"plate_lobe_d":{"label":"The left side's nut plate, each end's width round its bolt hole","kind":"length","measurements":[{"id":"derived","value":0.52,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.plate_lobe_d}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws)."},"plate_bar_height":{"label":"The nut plate's bar between its two ends, its height","kind":"length","measurements":[{"id":"derived","value":0.2,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{geissele-mk16-15-handguard.plate_bar_height}","via":"harvest"}}],"note":"The family's: taken from the 15 in rail's ledger by reference (the sellers' pages give the one height, width and inside for every length of the MK16, and the same sentences for its barrel nut, tabs and set screws)."}}},{"subject":"geissele-mk16-15-handguard","title":"Geissele Automatics 15 in Super Modular Rail MK16 M-LOK (05-792B)","dimensions":{"weight":{"label":"Weight on the rifle (the handguard with its barrel nut)","kind":"mass","measurements":[{"id":"mile-high","value":17.1,"unit":"oz","pm":0.05,"stated":"WEIGHT: 15.6oz (17.1oz w/ barrel nut)","source":{"type":"spec","publisher":"retailer","name":"Mile High Shooting Accessories, Geissele: 15\" Super Modular Rail MK16 M-LOK (05-792B), Specifications","url":"https://www.milehighshooting.com/geissele-15-super-modular-rail-mk16-m-lok/","retrieved":"2026-10-06","via":"harvest"}},{"id":"bullet-central","value":17.1,"unit":"oz","pm":0.05,"stated":"Weight for 15\": 15.6oz (17.1oz with barrel nut)","source":{"type":"spec","publisher":"retailer","name":"Bullet Central, Geissele Automatics - 15\" Super Modular Rail MK16 M-LOK, Black, Specifications","url":"https://bulletcentral.com/geissele-automatics-15-super-modular-rail-mk16-m-lok-black/","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":17.1,"unit":"oz","pm":0.05,"stated":"Weight 17.1 oz.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics MK16 Free Float AR-15 Handguard - M-LOK - 15\" (05-792B), specifications","url":"https://www.primaryarms.com/geissele-automatics-super-modular-rail-mk16-m-lok-black-15in","retrieved":"2026-10-06","via":"harvest"}},{"id":"charlies","value":15.8,"unit":"oz","pm":0.05,"stated":"SMR MK16 15\" WEIGHT: 14.2oz (15.8oz w/ barrel nut)","source":{"type":"spec","publisher":"retailer","name":"Charlie's Custom Clones, Geissele 15\" MK16 Super Modular Rail M-LOK - Black (05-792B), Specifications","url":"https://charliescustomclones.com/geissele-15-mk16-super-modular-rail-m-lok-black/","retrieved":"2026-10-06","via":"harvest"}},{"id":"kenzies","value":15.8,"unit":"oz","pm":0.05,"stated":"SMR MK16 15″ Weight 14.2oz (15.8oz w/ barrel nut)","source":{"type":"spec","publisher":"retailer","name":"Kenzie's Optics, Geissele MK16 Super Modular Rail M-LOK - Desert Dirt, Specifications (a table of the four lengths)","url":"https://www.kenziesoptics.com/product/geissele-mk16-super-modular/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"mile-high","reason":"Three sellers' pages for this one product (05-792B) against two; the model's metal as aluminium weighs nearer the handguard this pair leaves (weight_handguard). Only the maker settles it, and its page isn't read."},"note":"Sellers give two pairs of figures for this one product: 15.6 oz (17.1 with the barrel nut) and 14.2 oz (15.8 with it). Primary Arms' one figure is the first pair's with the nut. A third pair, 12.8 oz (14.44 with the nut), was seen only in a search engine's summary of a page that refuses the reader (Brownells): a lead, not a reading. The maker's own page isn't opened."},"weight_handguard":{"label":"Weight, the handguard alone","kind":"mass","measurements":[{"id":"mile-high","value":15.6,"unit":"oz","pm":0.05,"stated":"WEIGHT: 15.6oz (17.1oz w/ barrel nut)","source":{"type":"spec","publisher":"retailer","name":"Mile High Shooting Accessories, Geissele: 15\" Super Modular Rail MK16 M-LOK (05-792B), Specifications","url":"https://www.milehighshooting.com/geissele-15-super-modular-rail-mk16-m-lok/","retrieved":"2026-10-06","via":"harvest"}},{"id":"bullet-central","value":15.6,"unit":"oz","pm":0.05,"stated":"Weight for 15\": 15.6oz (17.1oz with barrel nut)","source":{"type":"spec","publisher":"retailer","name":"Bullet Central, Geissele Automatics - 15\" Super Modular Rail MK16 M-LOK, Black, Specifications","url":"https://bulletcentral.com/geissele-automatics-15-super-modular-rail-mk16-m-lok-black/","retrieved":"2026-10-06","via":"harvest"}},{"id":"charlies","value":14.2,"unit":"oz","pm":0.05,"stated":"SMR MK16 15\" WEIGHT: 14.2oz (15.8oz w/ barrel nut)","source":{"type":"spec","publisher":"retailer","name":"Charlie's Custom Clones, Geissele 15\" MK16 Super Modular Rail M-LOK - Black (05-792B), Specifications","url":"https://charliescustomclones.com/geissele-15-mk16-super-modular-rail-m-lok-black/","retrieved":"2026-10-06","via":"harvest"}},{"id":"kenzies","value":14.2,"unit":"oz","pm":0.05,"stated":"SMR MK16 15″ Weight 14.2oz (15.8oz w/ barrel nut)","source":{"type":"spec","publisher":"retailer","name":"Kenzie's Optics, Geissele MK16 Super Modular Rail M-LOK - Desert Dirt, Specifications (a table of the four lengths)","url":"https://www.kenziesoptics.com/product/geissele-mk16-super-modular/","retrieved":"2026-10-06","via":"harvest"}},{"id":"ar15discounts","value":14.2,"unit":"oz","pm":0.05,"stated":"Weight 14.2 oz","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, Geissele Automatics MK16 M-LOK AR-15 Super Modular Rail, Additional information (one figure for four lengths)","url":"https://ar15discounts.com/products/geissele-automatics-mk16-m-lok-ar-15-super-modular-rail/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"mile-high","reason":"The pair adopted for the weight on the rifle. The model's metal weighs between the two figures (the part's approximations say what)."},"note":"The same two pairs. AR15Discounts gives 14.2 oz as one figure on a page for all four lengths."},"length":{"label":"Length, end to end (its rear face to its muzzle end, the tabs behind the rear face left out)","kind":"length","measurements":[{"id":"mile-high","value":15,"unit":"in","pm":0.5,"stated":"LENGTH: 15\"","source":{"type":"spec","publisher":"retailer","name":"Mile High Shooting Accessories, Geissele: 15\" Super Modular Rail MK16 M-LOK (05-792B), Specifications","url":"https://www.milehighshooting.com/geissele-15-super-modular-rail-mk16-m-lok/","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":15,"unit":"in","pm":0.5,"stated":"Handguard Length 15","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics MK16 Free Float AR-15 Handguard - M-LOK - 15\" (05-792B), specifications","url":"https://www.primaryarms.com/geissele-automatics-super-modular-rail-mk16-m-lok-black-15in","retrieved":"2026-10-06","via":"harvest"}},{"id":"photo","value":15.12,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard 2b07184f9c79 (Primary Arms' gallery for 05-792B, 05-792B_02.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own top rail's 36 slots at the Picatinny pitch (std.picatinny.slot_pitch)","method":"the rail's top from its front end (px 114) to its rear end (px 2066): 35 pitches between the end slots' centres (px 198 and 1977.5), 84 px ahead of the first at 49.9 px a pitch and 88.5 px behind the last at 52.0: 38.39 pitches. A second fit of the same slots reads 38.27 (15.08 in): the ± (scratch/m2.py, m6.py)","via":"harvest"}}],"adopt":{"from":"photo","reason":"The sellers' figure is the size's name, good to half an inch; its own rail's slots count 15.12 in, inside that."},"note":"The sellers' 15 in is its size in whole inches. Its rail runs the whole length (the rail's ends and the body's stand within 0.06 in of each other at both ends on the level photo), and by its own slots it is 15.12 in."},"width":{"label":"Width across the side faces (3 to 9 o'clock)","kind":"length","measurements":[{"id":"mile-high","value":1.59,"unit":"in","pm":0.005,"stated":"OUTER DIAMETER (DAQ*): 1.59\" [...] *DAQ - Distance Across Quadrants","source":{"type":"spec","publisher":"retailer","name":"Mile High Shooting Accessories, Geissele: 15\" Super Modular Rail MK16 M-LOK (05-792B), Specifications","url":"https://www.milehighshooting.com/geissele-15-super-modular-rail-mk16-m-lok/","retrieved":"2026-10-06","via":"harvest"}},{"id":"charlies","value":1.59,"unit":"in","pm":0.005,"stated":"OUTER DIAMETER (DAQ*): 1.59\"","source":{"type":"spec","publisher":"retailer","name":"Charlie's Custom Clones, Geissele 15\" MK16 Super Modular Rail M-LOK - Black (05-792B), Specifications","url":"https://charliescustomclones.com/geissele-15-mk16-super-modular-rail-m-lok-black/","retrieved":"2026-10-06","via":"harvest"}},{"id":"bullet-central","value":1.59,"unit":"in","pm":0.005,"stated":"Outer Diameter (DAQ*): 1.59\"","source":{"type":"spec","publisher":"retailer","name":"Bullet Central, Geissele Automatics - 15\" Super Modular Rail MK16 M-LOK, Black, Specifications","url":"https://bulletcentral.com/geissele-automatics-15-super-modular-rail-mk16-m-lok-black/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"mile-high","reason":"Three sellers state the one figure."},"note":"The sellers' \"OUTER DIAMETER (DAQ*)\" with \"*DAQ - Distance Across Quadrants\": the distance across two opposite faces that carry M-LOK slots. Kenzie's Optics' view from the rear end reads 1.61 across the side faces when its rail is taken at the standard's 0.835 (105.8 px against 55): the same figure within the photo's 3%."},"height":{"label":"Height (the rail's top to the bottom of the clamp block at its rear end)","kind":"length","measurements":[{"id":"mile-high","value":2.39,"unit":"in","pm":0.005,"stated":"HEIGHT: 2.39\"","source":{"type":"spec","publisher":"retailer","name":"Mile High Shooting Accessories, Geissele: 15\" Super Modular Rail MK16 M-LOK (05-792B), Specifications","url":"https://www.milehighshooting.com/geissele-15-super-modular-rail-mk16-m-lok/","retrieved":"2026-10-06","via":"harvest"}},{"id":"charlies","value":2.39,"unit":"in","pm":0.005,"stated":"HEIGHT: 2.39\"","source":{"type":"spec","publisher":"retailer","name":"Charlie's Custom Clones, Geissele 15\" MK16 Super Modular Rail M-LOK - Black (05-792B), Specifications","url":"https://charliescustomclones.com/geissele-15-mk16-super-modular-rail-m-lok-black/","retrieved":"2026-10-06","via":"harvest"}},{"id":"gritr","value":2.39,"unit":"in","pm":0.005,"stated":"Height 2.39in","source":{"type":"spec","publisher":"retailer","name":"GritrSports, GEISSELE AUTOMATICS 15\" Super Modular Rail Mk16 M-Lok (05-792B), specifications","url":"https://gritrsports.com/geissele-automatics-15-super-modular-rail-mk16-m-lok-05-792b","retrieved":"2026-10-06","via":"harvest"}},{"id":"photo","value":2.37,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard 2b07184f9c79 (Primary Arms' gallery for 05-792B, 05-792B_02.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own rail's slots beside the column read: 52.0 px a pitch at the rear end, 131.9 px/in","method":"the rail's top (row 567.5) to the clamp block's bottom edge (row 880.5) at column 2000: 313 px (scratch/m1.py, m2.py)","via":"harvest"}}],"adopt":{"from":"mile-high","reason":"Three sellers state the one figure; the level photo reads it within 1% as the rail's top to the clamp block's bottom."},"note":"What the sellers' 2.39 in spans is read on the level photo: the rail's top to the bottom of the clamp block under the rear end is 2.37 in there; the rail's top to the bottom of the tube itself is 2.06 (body_bottom_below_bore)."},"inside_diameter":{"label":"Inside diameter","kind":"length","measurements":[{"id":"mile-high","value":1.26,"unit":"in","pm":0.005,"stated":"INNER DIAMETER: 1.26\"","source":{"type":"spec","publisher":"retailer","name":"Mile High Shooting Accessories, Geissele: 15\" Super Modular Rail MK16 M-LOK (05-792B), Specifications","url":"https://www.milehighshooting.com/geissele-15-super-modular-rail-mk16-m-lok/","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":1.26,"unit":"in","pm":0.005,"stated":"Inner Diameter 1.26","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics MK16 Free Float AR-15 Handguard - M-LOK - 15\" (05-792B), specifications","url":"https://www.primaryarms.com/geissele-automatics-super-modular-rail-mk16-m-lok-black-15in","retrieved":"2026-10-06","via":"harvest"}},{"id":"bullet-central","value":1.26,"unit":"in","pm":0.005,"stated":"Inner Diameter: 1.26\"","source":{"type":"spec","publisher":"retailer","name":"Bullet Central, Geissele Automatics - 15\" Super Modular Rail MK16 M-LOK, Black, Specifications","url":"https://bulletcentral.com/geissele-automatics-15-super-modular-rail-mk16-m-lok-black/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"mile-high","reason":"Three sellers state the one figure."},"note":"Sellers' \"INNER DIAMETER\". Its rear end is a round bore over the barrel nut (Kenzie's Optics' view from the rear); ahead of it the inside has flat walls that follow the outside (Bullet Central's and Primary Arms' views of the muzzle end), and the model takes this figure as the circle those inner walls touch. Primary Arms' page for the 13.5 in rail says 1.35 in once, against 1.26 on its pages for this one and the 10.5 in."},"rear_face_x":{"label":"Its rear face against the receiver's front face (negative: behind it)","kind":"length","measurements":[{"id":"derived","value":-0.445,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"0in - {std.ar15.upper_barrel_thread_length}","via":"harvest"}}],"note":"No page read says where it stops, and no photo of it mounted is on file. It slides back over its barrel nut; its rear face is taken to meet the receiver's front shoulder, where the barrel-nut thread begins (std.ar15.upper_barrel_thread_length behind the front face), with no gap. A check: its rail's first slot then stands 0.04 in ahead of where the receiver's own row of slots would continue (bcm-m4-upper: 13 slots from 1.31 in at the standard's pitch), inside what the two readings allow."},"tab_length":{"label":"Its lower tabs' reach behind its rear face","kind":"length","measurements":[{"id":"photo","value":0.26,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard 2b07184f9c79 (Primary Arms' gallery for 05-792B, 05-792B_02.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own rail's slots at the rear end (52.0 px a pitch), 1.5% more on the near side face: 133 px/in","method":"the tab's rear end (px 2107) behind the rear face's edge (px 2072.5) on a gridded crop (scratch/grid2.py)","via":"harvest"}}],"note":"A tab on each side behind the clamp block, each with a set screw through it across the rifle (sellers: \"Anti-rotation tabs and set-screws ensure that your rail will not rotate\"). They lie along the receiver's sides."},"rear_x":{"label":"The outline's rear end (its lower tabs' ends) against the receiver's front face (negative: behind it)","kind":"length","measurements":[{"id":"derived","value":-0.705,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{.rear_face_x} - {.tab_length}","via":"harvest"}}]},"overall_length":{"label":"Length over all, its lower tabs' ends to its muzzle end","kind":"length","measurements":[{"id":"derived","value":15.38,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{.length} + {.tab_length}","via":"harvest"}}]},"tab_top_below_bore":{"label":"Its lower tabs' top edge below the bore axis","kind":"length","measurements":[{"id":"photo","value":0.27,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard 2b07184f9c79 (Primary Arms' gallery for 05-792B, 05-792B_02.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own rail's slots at the rear end: 132 px/in","method":"the tab's top edge (row 760) below the side faces' middle line (row 724.3 there) on a gridded crop (scratch/grid2.py)","via":"harvest"}}]},"tab_bottom_below_bore":{"label":"Its lower tabs' bottom edge below the bore axis","kind":"length","measurements":[{"id":"photo","value":0.64,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard 2b07184f9c79 (Primary Arms' gallery for 05-792B, 05-792B_02.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own rail's slots at the rear end: 132 px/in","method":"the tab's bottom edge (row 808) below the side faces' middle line (row 724.3 there) on a gridded crop (scratch/grid2.py)","via":"harvest"}}]},"tab_screw_d":{"label":"A tab's set screw, its diameter as it shows from the side","kind":"length","measurements":[{"id":"photo","value":0.14,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard 2b07184f9c79 (Primary Arms' gallery for 05-792B, 05-792B_02.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own rail's slots at the rear end: 132 px/in","method":"the screw's dark round end in the tab, 18 to 19 px across, its centre at px (2090.7, 788): 0.14 in behind the rear face and 0.48 below the bore (scratch/grid2.py)","via":"harvest"}}]},"tongue_length":{"label":"Its upper tabs' reach behind its rear face","kind":"length","measurements":[{"id":"photo","value":0.12,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard 2b07184f9c79 (Primary Arms' gallery for 05-792B, 05-792B_02.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own rail's slots at the rear end: 133 px/in on the near face","method":"the upper tab's rear end (px 2088) behind the rear face's edge (px 2072.5) on a gridded crop (scratch/grid2.py)","via":"harvest"}}],"note":"A thin tab on each side under the rail's rear end, shorter than the lower ones: the anti-rotation tabs the sellers name, beside the receiver's flat sides (upper_tab_gap)."},"upper_tab_gap":{"label":"The opening between its two upper tabs","kind":"length","measurements":[{"id":"derived","value":0.638,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"2 * {bcm-m4-upper.side_half_width}","via":"harvest"}}],"note":"Not measured: no view shows it square on. The tabs stand beside a mil-spec receiver's flat sides under its rail (0.56 to 0.82 in above the bore on the catalog's receivers), which is what keeps the rail from turning, and they are drawn against those flats with no clearance. Primary Arms' view from behind (413379c0fd31) shows the far tab's inner face a little outside the channel's wall, as this figure has it (0.638 against the channel's 0.47)."},"tongue_bottom_above_bore":{"label":"Its upper tabs' bottom edge above the bore axis","kind":"length","measurements":[{"id":"photo","value":0.545,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard 2b07184f9c79 (Primary Arms' gallery for 05-792B, 05-792B_02.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own rail's slots at the rear end: 132 px/in","method":"the upper tab's bottom edge (row 652) above the side faces' middle line (row 724.3 there) (scratch/grid2.py)","via":"harvest"}}]},"tongue_top_above_bore":{"label":"Its upper tabs' top edge above the bore axis","kind":"length","measurements":[{"id":"photo","value":0.727,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard 2b07184f9c79 (Primary Arms' gallery for 05-792B, 05-792B_02.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own rail's slots at the rear end: 132 px/in","method":"the upper tab's top edge (row 628) above the side faces' middle line (row 724.3 there) (scratch/grid2.py)","via":"harvest"}}]},"rail_top_above_bore":{"label":"Its rail's top above the bore axis","kind":"length","measurements":[{"id":"photo","value":1.2,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard 2b07184f9c79 (Primary Arms' gallery for 05-792B, 05-792B_02.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own rail's slots beside the column read: 51.3 px a pitch, 130.2 px/in","method":"at column 1450, where the lens stood over it: the rail's top (row 566.5) above the middle of the side face (its two creases, rows 680 and 758.3 at the muzzle end, 3.5 px lower here by the photo's 0.2° of tilt: row 722.8): 156.3 px (scratch/m1.py, m3.py)","via":"harvest"}},{"id":"rear-view","value":1.22,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard b257c1202ea0 (Kenzie's Optics' gallery, mk16-ddc-1.webp: a short Desert Dirt MK16 seen from its rear end, nearly end on and a little from above, 504 x 504)","scaleRef":"its width across the side faces (this ledger's width) over 105.8 px: 66.6 px/in across; heights 0.955 of that, by the barrel nut's ring (530 px tall, 555 wide on a 6x crop)","method":"the rail's top edge (row 247.5) above the middle of the two side faces (rows 306.7 to 343.3: 325): 77.5 px (scratch/grid.py)","via":"harvest"},"note":"A shorter rail of the same model (the 9.3 or 10.5 in), at a seventh of the level photo's resolution."}],"adopt":{"from":"photo","reason":"The level photo of this rail, at the higher resolution; the view from the rear end of a shorter one agrees within its own ±."},"note":"Not published. The bore's axis is taken at the middle of its side faces, which the middle rows of slots stand on. The catalog's mil-spec receivers have their rail 1.2125 and 1.2145 in above the bore (bcm-m4-upper, expo-arms-stripped-upper)."},"body_bottom_below_bore":{"label":"The tube's bottom flat below the bore axis","kind":"length","measurements":[{"id":"photo","value":0.86,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard 2b07184f9c79 (Primary Arms' gallery for 05-792B, 05-792B_02.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own rail's slots beside the column read: 51.3 px a pitch, 130.2 px/in","method":"at column 1450: the tube's bottom edge (row 835) below the middle of the side face (row 722.8): 112.2 px; at the muzzle end the same reads 0.88 (113 px at 128 px/in) (scratch/m1.py)","via":"harvest"}}],"note":"Lower than half its width: the section isn't a regular octagon. Its faces between the sides and the bottom are longer than those between the sides and the rail (0.57 against 0.39 in of height on the level photo), and its bottom flat is the narrower for it."},"side_flat_height":{"label":"The side faces' height (crease to crease)","kind":"length","measurements":[{"id":"photo","value":0.6,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard 2b07184f9c79 (Primary Arms' gallery for 05-792B, 05-792B_02.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own rail's slots at the muzzle end (49.9 px a pitch), 1.5% more on the near face: 128.5 px/in","method":"the side face's two creases at the muzzle end, rows 680 and 758.3 on a 3x crop, and the flat tips of the muzzle end's outline (rows 680 to 756): 77 px (scratch/m3.py)","via":"harvest"}},{"id":"rear-view","value":0.577,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard b257c1202ea0 (Kenzie's Optics' gallery, mk16-ddc-1.webp: a short Desert Dirt MK16 seen from its rear end, nearly end on and a little from above, 504 x 504)","scaleRef":"its width across the side faces (this ledger's width) over 105.8 px: 66.6 px/in across; heights 0.955 of that","method":"the side faces' vertical edges on the rear face, rows 306.7 to 343.3: 36.7 px (scratch/grid.py)","via":"harvest"}}],"adopt":{"from":"photo","reason":"The level photo of this rail, at the higher resolution; the rear view of a shorter one agrees within its ±."},"note":"A regular octagon 1.59 in across would have 0.659 here. Where the faces at 45° begin, top and bottom."},"diag_face_distance":{"label":"The faces between the sides and the rail or the bottom: their distance from the bore axis","kind":"length","measurements":[{"id":"derived","value":0.774282,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"({.width} / 2 + {.side_flat_height} / 2) * cos(45)","via":"harvest"}}],"note":"Taken at 45° through the side faces' creases. The angle isn't published: Kenzie's Optics' rear view draws these faces at 44° (185 px across, 178 up once its heights are put right), and on the level photo their slots show 0.66 to 0.70 of the side rows' slots' height (45° shows 0.71)."},"neck_base_above_bore":{"label":"Where the upper faces end and the neck under the rail begins, above the bore","kind":"length","measurements":[{"id":"photo","value":0.695,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard 2b07184f9c79 (Primary Arms' gallery for 05-792B, 05-792B_02.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own rail's slots at the muzzle end, 1.5% more on the near face: 128.5 px/in","method":"the crease above the upper row of slots (row 630 on a 3x crop of the muzzle end) above the middle of the side face (row 719.2): 89.2 px. Bullet Central's view of a shorter rail's muzzle end reads the upper face 0.38 in tall beside a side face of 0.59, the same within 0.02 (scratch/m3.py, grid.py)","via":"harvest"}}]},"neck_chamfer_height":{"label":"The slope between the upper faces and the neck's walls, its height","kind":"length","measurements":[{"id":"photo","value":0.08,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard 2b07184f9c79 (Primary Arms' gallery for 05-792B, 05-792B_02.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own rail's slots at the muzzle end, 1.5% more on the near face: 128.5 px/in","method":"the lighter band between the upper face and the dark wall under the rail, rows 620 to 630 on a 3x crop of the muzzle end (scratch/m3.py)","via":"harvest"}}]},"neck_width":{"label":"The neck's width under the rail","kind":"length","measurements":[{"id":"rear-view","value":0.61,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard b257c1202ea0 (Kenzie's Optics' gallery, mk16-ddc-1.webp: a short Desert Dirt MK16 seen from its rear end, nearly end on and a little from above, 504 x 504)","scaleRef":"its width across the side faces (this ledger's width) over 105.8 px: 66.6 px/in","method":"the neck's two outer walls on the rear face, 40 px apart on a 6x gridded crop; its rail reads 0.826 in wide at this scale against the standard's 0.835 (scratch/grid.py)","via":"harvest"},"note":"A shorter rail of the same model, seen at its rear end."}]},"channel_width":{"label":"The channel under the rail (the gas tube's), its width","kind":"length","measurements":[{"id":"rear-view","value":0.47,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard b257c1202ea0 (Kenzie's Optics' gallery, mk16-ddc-1.webp: a short Desert Dirt MK16 seen from its rear end, nearly end on and a little from above, 504 x 504)","scaleRef":"its width across the side faces (this ledger's width) over 105.8 px: 66.6 px/in","method":"the dark opening under the rail on the rear face, 30.8 px wide on a 6x gridded crop; Bullet Central's and Primary Arms' views of the muzzle end show the same open channel there (scratch/grid.py)","via":"harvest"}}]},"channel_roof_below_top":{"label":"The channel's roof below the rail's top","kind":"length","measurements":[{"id":"rear-view","value":0.18,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard b257c1202ea0 (Kenzie's Optics' gallery, mk16-ddc-1.webp: a short Desert Dirt MK16 seen from its rear end, nearly end on and a little from above, 504 x 504)","scaleRef":"its width across the side faces over 105.8 px: 66.6 px/in across; heights 0.955 of that","method":"the opening's top edge (row 259.2) below the rail's top edge (row 247.5): 11.7 px (scratch/grid.py)","via":"harvest"}}]},"rail_body_height":{"label":"The rail's depth, its top to where the neck's wall begins","kind":"length","measurements":[{"id":"photo","value":0.18,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard 7c61cabf5c93 (Bullet Central's gallery: a short Desert Dirt MK16 seen from ahead, above and its right, the muzzle end's section toward the lens, 3906 x 1464)","scaleRef":"the side face's height on the muzzle end's face (this ledger's side_flat_height over 165 px: 280 px/in up and down that face)","method":"on the muzzle end's face: the rail's top corner (row 650) to where its sloped underside meets the neck's wall (row 700): 50 px, 18 of them the rail's upright edge (scratch/grid.py)","via":"harvest"},"note":"A shorter rail of the same model."}],"note":"A check, not what the model draws: its rail's head is MIL-STD-1913's Figure 1 (std.picatinny.*; sellers: \"M1913 picatinny rail\"), whose lower 45° faces reach a neck of this ledger's width 0.223 in below the top."},"rail_bevel":{"label":"The rail's edge between its sloped faces, how much of it is sloped above and below","kind":"length","measurements":[{"id":"photo","value":0.06,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard 7c61cabf5c93 (Bullet Central's gallery: a short Desert Dirt MK16 seen from ahead, above and its right, the muzzle end's section toward the lens, 3906 x 1464)","scaleRef":"the side face's height on the muzzle end's face: 280 px/in","method":"the rail's edge is upright for 18 px (0.064 in) of its 50, which leaves 0.06 each for the slopes above and below it if they are alike; the photo's lower slope alone reads 0.11 (scratch/grid.py)","via":"harvest"}}],"note":"A check, not what the model draws (the standard's head: rail_body_height's note)."},"rail_slots":{"label":"Slots in its top rail","kind":"count","measurements":[{"id":"photo","value":36,"unit":"count","source":{"type":"photo","photo":"references/geissele-mk16-15-handguard 2b07184f9c79 (Primary Arms' gallery for 05-792B, 05-792B_02.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"none: a count","method":"the notches between the teeth along the top edge: 36, centres from px 198 to px 1977.5, each 49 to 52.5 px from the next with none missing; a longer tooth at each end (scratch/m2.py, m3.py)","via":"harvest"}}]},"rail_slot0_from_rear":{"label":"Its rail's rearmost slot (its centre) ahead of its rear face","kind":"length","measurements":[{"id":"photo","value":0.67,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard 2b07184f9c79 (Primary Arms' gallery for 05-792B, 05-792B_02.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own rail's slots at the rear end: 52.0 px a pitch","method":"the rail's rear end (px 2066) behind the rearmost slot's centre (px 1977.5): 88.5 px, 1.70 pitches. The rail's rear end and the body's rear face are one plane within 0.05 in (scratch/m2.py)","via":"harvest"}}]},"rail_slot0_x":{"label":"Its rail's rearmost slot (its centre) ahead of the receiver's front face","kind":"length","measurements":[{"id":"derived","value":0.225,"unit":"in","pm":0.045,"source":{"type":"derived","expr":"{.rear_face_x} + {.rail_slot0_from_rear}","via":"harvest"}}]},"rail_front_from_last_slot":{"label":"Its rail's front end ahead of its last slot's centre","kind":"length","measurements":[{"id":"photo","value":0.663,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard 2b07184f9c79 (Primary Arms' gallery for 05-792B, 05-792B_02.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own rail's slots at the muzzle end: 49.9 px a pitch","method":"the rail's front end (px 114) ahead of the frontmost slot's centre (px 198): 84 px, 1.68 pitches (scratch/m2.py, m3.py)","via":"harvest"}}]},"mlok_side_slots":{"label":"M-LOK slots on each side face (3 and 9 o'clock)","kind":"count","measurements":[{"id":"photo","value":8,"unit":"count","source":{"type":"photo","photo":"references/geissele-mk16-15-handguard 2b07184f9c79 (Primary Arms' gallery for 05-792B, 05-792B_02.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"none: a count","method":"the middle row's slots, light showing through each: eight, 200 to 208 px apart (scratch/m5.py); eight on the right side in Mile High's photo (aba62637245f)","via":"harvest"}}]},"mlok_lower_slots":{"label":"M-LOK slots on each lower face (between the sides and the bottom)","kind":"count","measurements":[{"id":"photo","value":8,"unit":"count","source":{"type":"photo","photo":"references/geissele-mk16-15-handguard 2b07184f9c79 (Primary Arms' gallery for 05-792B, 05-792B_02.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"none: a count","method":"the lower row's slots, light showing through each: eight, their ends within 0.02 in of the side row's once each row is read at its own depth (scratch/m5.py)","via":"harvest"}}]},"mlok_upper_slots":{"label":"M-LOK slots on each upper face (between the sides and the rail)","kind":"count","measurements":[{"id":"photo","value":7,"unit":"count","source":{"type":"photo","photo":"references/geissele-mk16-15-handguard 2b07184f9c79 (Primary Arms' gallery for 05-792B, 05-792B_02.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"none: a count","method":"the upper row's slots on the photo at full size: seven, each over one of the side row's front seven (their rear ends at px 1122, 1325, 1529 against the side row's 1124, 1332, 1532); seven on the right side in Primary Arms' view from above and ahead (6a8917d6710f)","via":"harvest"}}],"note":"One fewer than the side faces: where the rearmost would be, the upper face carries a sling swivel socket."},"mlok_bottom_slots":{"label":"M-LOK slots on its underside (6 o'clock)","kind":"count","measurements":[{"id":"derived","value":8,"unit":"count","source":{"type":"derived","expr":"{.mlok_side_slots}","via":"harvest"}}],"note":"The row is the sellers' sentence: \"M-LOK slots on every quadrant\" (Mile High, Primary Arms, Rifle Supply); Primary Arms of the 13.5 in rail: \"seven sides of M-LOK slots\". No photo on file shows the underside, so how many slots it has isn't counted: it is taken to have the side rows' eight, which is what fits ahead of the clamp block (mlok_bottom_slot0_x). An assumption, not a count."},"mlok_bottom_slot0_x":{"label":"The underside's rearmost M-LOK slot (its centre) ahead of the receiver's front face","kind":"length","measurements":[{"id":"derived","value":2.635,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{.mlok_side_slot0_x}","via":"harvest"}}],"note":"Not seen: taken at the side rows' stations (the three rows that are seen on each side stand in line with each other). The clamp block and its split take the rear of the bottom; the side rows' rearmost slot begins 2.45 in ahead of the rear face, 0.05 in ahead of where the block's front ramp ends on the traced outline (2.40), so the row starts there and all eight are ahead of the block. An assumption."},"mlok_side_slot0_from_rear":{"label":"The side faces' rearmost M-LOK slot (its centre) ahead of the rear face","kind":"length","measurements":[{"id":"photo","value":3.08,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard 2b07184f9c79 (Primary Arms' gallery for 05-792B, 05-792B_02.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own rail's slots as a ruler (a quadratic fit of their centres), the near face brought to its true place about column 1375 by k 1.02","method":"the rear ends of the six slots ahead of the lens (where the near slot's own edge bounds the light): rail coordinates -0.537, 3.486, 7.489, 11.509, 15.489, 19.487 once corrected, 3.997 pitches apart within 0.03; the rearmost slot's rear end then 6.255 pitches (2.464 in) ahead of the rail's rear end (33.697), its centre half a slot (std.mlok.slot_length) further: 3.094. The rearmost slot's own front end, read from the other side of the lens (rail coordinate 24.304), puts its centre at 3.071: the value is between the two (scratch/m5.py)","via":"harvest"}}]},"mlok_side_slot0_x":{"label":"The side and lower faces' rearmost M-LOK slot (its centre) ahead of the receiver's front face","kind":"length","measurements":[{"id":"derived","value":2.635,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{.rear_face_x} + {.mlok_side_slot0_from_rear}","via":"harvest"}}]},"mlok_upper_slot0_x":{"label":"The upper faces' rearmost M-LOK slot (its centre) ahead of the receiver's front face","kind":"length","measurements":[{"id":"derived","value":4.209803,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{.mlok_side_slot0_x} + {std.mlok.slot_pitch}","via":"harvest"}}],"note":"One slot pitch ahead of the side faces' rearmost: the upper rows have the side rows' front seven."},"mlok_upper_row_above_bore":{"label":"The upper rows of slots, their middle line above the bore","kind":"length","measurements":[{"id":"photo","value":0.51,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard 2b07184f9c79 (Primary Arms' gallery for 05-792B, 05-792B_02.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own rail's slots at the muzzle end, 1% more at this face's depth: 128 px/in","method":"the upper row's slots' middle (row 654 on a 3x crop of the muzzle end) above the middle of the side face (row 719.2): 65 px (scratch/m3.py)","via":"harvest"}}]},"mlok_lower_row_below_bore":{"label":"The lower rows of slots, their middle line below the bore","kind":"length","measurements":[{"id":"photo","value":0.565,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard 2b07184f9c79 (Primary Arms' gallery for 05-792B, 05-792B_02.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own rail's slots at the muzzle end, 1% more at this face's depth: 128 px/in","method":"the lower row's slots' middle (row 792 on a 3x crop of the muzzle end) below the middle of the side face (row 719.2): 72.5 px (scratch/m3.py)","via":"harvest"}}]},"reach_inside":{"label":"The room inside its faces, from a face in to the barrel (what an M-LOK accessory's nuts may take)","kind":"length","measurements":[],"note":"Not sourced: it depends on the barrel and gas block under it, other parts. Its side walls are 0.165 in by the sellers' two figures (1.59 across, 1.26 inside)."},"socket_from_rear":{"label":"The sling swivel sockets (their centres) ahead of the rear face","kind":"length","measurements":[{"id":"photo","value":2.77,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard 2b07184f9c79 (Primary Arms' gallery for 05-792B, 05-792B_02.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own rail's slots as a ruler, the near face brought to its true place about column 1375 by k 1.015 (this face's depth)","method":"the cup's centre (px 1706.7) as rail coordinate 26.66 once corrected, 7.04 pitches ahead of the rail's rear end (scratch/grid2.py, m5.py)","via":"harvest"}}],"note":"A round steel cup let into each upper face at the rear, where that face has no slot: on the left side in Primary Arms' photos and on the right in Mile High's."},"socket_above_bore":{"label":"The sling swivel sockets' centres above the bore","kind":"length","measurements":[{"id":"photo","value":0.585,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard 2b07184f9c79 (Primary Arms' gallery for 05-792B, 05-792B_02.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own rail's slots at the rear end: 131.5 px/in","method":"the cup's centre (row 648.3) above the side faces' middle line (row 725.3 there): 77 px (scratch/grid2.py)","via":"harvest"}}]},"socket_ring_d":{"label":"A sling swivel socket's cup, its outside diameter","kind":"length","measurements":[{"id":"photo","value":0.545,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard 2b07184f9c79 (Primary Arms' gallery for 05-792B, 05-792B_02.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own rail's slots at the rear end: 131.5 px/in","method":"the cup's bright rim along the rifle, where the face's slope doesn't shorten it: 71.7 px on a 3x gridded crop (scratch/grid2.py)","via":"harvest"}}]},"socket_hole_d":{"label":"A sling swivel socket's hole, its diameter","kind":"length","measurements":[{"id":"photo","value":0.31,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard 2b07184f9c79 (Primary Arms' gallery for 05-792B, 05-792B_02.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own rail's slots at the rear end: 131.5 px/in","method":"the dark hole inside the cup's rim along the rifle: 40.7 px on a 3x gridded crop (scratch/grid2.py)","via":"harvest"}}]},"cross_bolt_front_from_rear":{"label":"The front cross bolt (its centre) ahead of the rear face","kind":"length","measurements":[{"id":"photo","value":1.57,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard 2b07184f9c79 (Primary Arms' gallery for 05-792B, 05-792B_02.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own rail's slots at the rear end, 1.5% more on the near face: 132.5 px/in","method":"the front hole of the plate (px 1864, 822.7) ahead of the rear face's edge (px 2072.5) on a 3x gridded crop (scratch/grid2.py)","via":"harvest"}}],"note":"Two bolts across the clamp block under the tube, their Torx heads on the right side (Mile High's photo) and a plate with two threaded holes on the left (Primary Arms')."},"cross_bolt_rear_from_rear":{"label":"The rear cross bolt (its centre) ahead of the rear face","kind":"length","measurements":[{"id":"photo","value":0.55,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard 2b07184f9c79 (Primary Arms' gallery for 05-792B, 05-792B_02.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own rail's slots at the rear end, 1.5% more on the near face: 132.5 px/in","method":"the rear hole of the plate (px 1999.3, 835) ahead of the rear face's edge (px 2072.5); the two holes 1.02 in apart, and the two Torx heads 1.01 apart on Mile High's photo of the right side (83 px at 82 px/in by the rail's teeth there) (scratch/grid2.py)","via":"harvest"}}]},"cross_bolt_front_below_bore":{"label":"The front cross bolt's centre below the bore","kind":"length","measurements":[{"id":"photo","value":0.745,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard 2b07184f9c79 (Primary Arms' gallery for 05-792B, 05-792B_02.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own rail's slots at the rear end: 132.5 px/in on the near face","method":"the front hole's centre (row 822.7) below the side faces' middle line (row 724 there) (scratch/grid2.py)","via":"harvest"}}]},"cross_bolt_rear_below_bore":{"label":"The rear cross bolt's centre below the bore","kind":"length","measurements":[{"id":"photo","value":0.835,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard 2b07184f9c79 (Primary Arms' gallery for 05-792B, 05-792B_02.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own rail's slots at the rear end: 132.5 px/in on the near face","method":"the rear hole's centre (row 835) below the side faces' middle line (row 724.3 there) (scratch/grid2.py)","via":"harvest"}}],"note":"Lower than the front one, on both sides' photos (0.09 in on the left, 0.11 on the right)."},"cross_bolt_hole_d":{"label":"A cross bolt's threaded hole in the left side's plate, its diameter","kind":"length","measurements":[{"id":"photo","value":0.21,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard 2b07184f9c79 (Primary Arms' gallery for 05-792B, 05-792B_02.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own rail's slots at the rear end: 132.5 px/in on the near face","method":"each round hole in the plate, 28 px across on a 3x gridded crop (scratch/grid2.py)","via":"harvest"}}]},"cross_bolt_head_d":{"label":"A cross bolt's Torx head on the right side, its diameter","kind":"length","measurements":[{"id":"photo","value":0.32,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard aba62637245f (Mile High Shooting's photo for 05-792B: the handguard alone, its right side, the rear end nearer the lens, 1280 x 1091)","scaleRef":"its own rail's teeth beside the heads: 32 px a pitch, 81.2 px/in","method":"each bright head, 26 px across on a 5x gridded crop, in a dark counterbore of 38 px (0.46 in) (scratch/grid2.py)","via":"harvest"}}]},"cross_bolt_counterbore_d":{"label":"A cross bolt's counterbore on the right side, its diameter","kind":"length","measurements":[{"id":"photo","value":0.46,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard aba62637245f (Mile High Shooting's photo for 05-792B: the handguard alone, its right side, the rear end nearer the lens, 1280 x 1091)","scaleRef":"its own rail's teeth beside the heads: 32 px a pitch, 81.2 px/in","method":"the dark ring round each head, 38 px across on a 5x gridded crop (scratch/grid2.py)","via":"harvest"}}]},"clamp_gap_width":{"label":"The clamp block's split along its underside, its width","kind":"length","measurements":[{"id":"rear-view","value":0.51,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard b257c1202ea0 (Kenzie's Optics' gallery, mk16-ddc-1.webp: a short Desert Dirt MK16 seen from its rear end, nearly end on and a little from above, 504 x 504)","scaleRef":"its width across the side faces (this ledger's width) over 105.8 px: 66.6 px/in","method":"the dark channel in the middle of the block's rear face, from its bottom up to the barrel nut: 34 px wide on a 6x gridded crop (scratch/grid.py)","via":"harvest"},"note":"A shorter rail of the same model."}],"note":"The block under the rear end is two halves with a channel between them, drawn together by the cross bolts. How far forward the channel runs isn't seen."},"plate_lobe_d":{"label":"The left side's nut plate, each end's width round its bolt hole","kind":"length","measurements":[{"id":"photo","value":0.52,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard 2b07184f9c79 (Primary Arms' gallery for 05-792B, 05-792B_02.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own rail's slots at the rear end: 132.5 px/in on the near face","method":"the front lobe 66.7 px along the rifle and 65 up and down, the rear one 71.7 and 65, on a 3x gridded crop (scratch/grid2.py)","via":"harvest"}}],"note":"A steel plate let into the clamp block's left side, with the two cross bolts' threaded holes in it: a lobe round each hole and a bar between them. The lobes are six-sided with round corners; the model draws them round."},"plate_bar_height":{"label":"The nut plate's bar between its two ends, its height","kind":"length","measurements":[{"id":"photo","value":0.2,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-mk16-15-handguard 2b07184f9c79 (Primary Arms' gallery for 05-792B, 05-792B_02.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own rail's slots at the rear end: 132.5 px/in on the near face","method":"the bar between the lobes, rows 803 to 830: 27 px on a 3x gridded crop (scratch/grid2.py)","via":"harvest"}}]}}},{"subject":"geissele-premium-mil-spec-buffer-tube-assembly-castle-nut","title":"Geissele Automatics Premium Mil-Spec Buffer Tube Assembly, its castle nut","dimensions":{"od":{"label":"Outside diameter","kind":"length","measurements":[{"id":"model","value":1.363,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"one cylinder, r 0.6815 (.cache/buffer/std/faces.Buffer_Tube_Nut.txt)","via":"user"}},{"id":"photo","value":1.333,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-premium-mil-spec-buffer-tube 7564882554c6 (Charlie's Custom Clones' picture of five assemblies under one light, 3300 x 1696: the black one at the bottom, its nut and plate on it, seen from the side)","scaleRef":"the tube's own outside diameter beside it in the same picture, taken as the mil-spec 1.148 (geissele-premium-mil-spec-buffer-tube.tube_od): 208.5 px between rows 1064 and 1272 behind the nut","method":"the nut's silhouette top to bottom, rows 1044 to 1286 (on a 2x crop): 242 px, 1.161 times the tube's","via":"harvest"},"note":"A black tube's edge reads thin and so does the nut's: their ratio is the reading."}],"adopt":{"from":"model","reason":"A mil-spec nut, as every seller says the assembly's is; the one photo that shows it beside the tube puts it within its ± of the model's."}},"thickness":{"label":"Thickness","kind":"length","measurements":[{"id":"model","value":0.3765,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"its front face to its rear face, planes y 0 and y 0.3765","via":"user"}}],"note":"No photo on file shows the nut square from the side: on the tube in Charlie's picture the tube is turned a little, and the nut's rear face shows as a band beside its side."},"notches":{"label":"Wrench notches in its rear face","kind":"count","measurements":[{"id":"photo","value":4,"unit":"count","source":{"type":"photo","photo":"references/geissele-premium-mil-spec-buffer-tube 40caefb1150b (Primary Arms' 08-162B_03: the black tube with its plate and nut, the nut lying on its front face, seen from above and in front)","scaleRef":"none: a count","method":"counted round the rear face, every quarter turn: one at the top, one each side, one at the near side, the whole ring in view","via":"harvest"},"note":"Charlie's gray assembly (234b20bbfb70) shows the same four."}]},"notch_width":{"label":"Wrench notch width","kind":"length","measurements":[{"id":"model","value":0.162,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"a wrench notch's two side planes, ±0.0810","via":"user"}}]},"notch_depth":{"label":"Wrench notch depth (into the rear face)","kind":"length","measurements":[{"id":"model","value":0.1375,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"a wrench notch's floor plane, y 0.2390 of 0.3765","via":"user"}}]},"staking_notches":{"label":"Staking notches in its front face's outer edge","kind":"count","measurements":[{"id":"model","value":3,"unit":"count","source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"three notches 120 degrees apart, counted in the face list (planes #20197, #20323 and their like)","via":"user"}}],"note":"One shows in each photo that sees the front face's edge (the flat lay's near side, under the near wrench notch; the side of the nut on the tube in Charlie's picture): the others are behind. The count is the reference model's."},"staking_notch_width":{"label":"Staking notch, width","kind":"length","measurements":[{"id":"model","value":0.09,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"a notch's two side planes, ±0.0450","via":"user"}}]},"staking_notch_depth":{"label":"Staking notch, depth into the front face","kind":"length","measurements":[{"id":"model","value":0.082,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"a notch's floor","via":"user"}}]},"staking_notch_radial":{"label":"Staking notch, how far in from the outside it is cut","kind":"length","measurements":[{"id":"model","value":0.075,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the notch's inner wall, a cylinder r 0.6065 of an outside r 0.6815","via":"user"}}]},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"metal","value":0.59,"unit":"oz","pm":0.06,"source":{"type":"derived","expr":"(0.785398163 * ({.od} * {.od} - {std.receiver_extension.thread_major_d} * {std.receiver_extension.thread_major_d}) * {.thickness} - {.notches} * {.notch_width} * {.notch_depth} * ({.od} - {std.receiver_extension.thread_major_d}) / 2) * {std.density.steel}","via":"harvest"}}],"note":"No page states it. Worked out from its sizes: a steel ring of its outside diameter and thickness round the extension's thread, less its four wrench notches, as steel (a mil-spec nut is steel; no page on file says what this one is made of)."}}},{"subject":"geissele-premium-mil-spec-buffer-tube-assembly-end-plate","title":"Geissele Automatics Premium Mil-Spec Buffer Tube Assembly, its end plate","dimensions":{"thickness":{"label":"Thickness","kind":"length","measurements":[{"id":"model","value":0.124,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the plate's two faces, planes y 0 and y 0.1240 (.cache/buffer/std/faces.Buffer_Tube_Rotation_Lock.txt)","via":"user"},"note":"A mil-spec plate as the reference model has it."}],"note":"A stamped plate: no page states its thickness, and no photo on file shows it edge on."},"top_above_axis":{"label":"End plate top above the tube axis (its ring's radius)","kind":"length","measurements":[{"id":"model","value":0.6817,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the ring's outer cylinder, r 0.6817 (#899)","via":"user"}},{"id":"photo","value":0.691,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-premium-mil-spec-buffer-tube 40caefb1150b (Primary Arms' 08-162B_03: the black tube with its plate and nut, the plate face on, tilted back: its hole 0.746 as tall as wide)","scaleRef":"across the picture, where the tilt changes nothing: the hole's width taken as a mil-spec plate's (std.receiver_extension.end_plate_hole_d, 1.1902), 335 px, 281.5 px/in","method":"the ring's width across the hole's widest row (row 973, luminance under 150): 389 px, halved","via":"harvest"},"note":"The outline's dark edge takes in a few pixels of shadow either side."}],"adopt":{"from":"model","reason":"A mil-spec plate, as Charlie's says the assembly's is, and as every photo on file shows it; the one width a photo gives square across agrees within its ±."}},"bottom_below_axis":{"label":"End plate lobe bottom below the tube axis","kind":"length","measurements":[{"id":"model","value":1.3788,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the lobe's round end, r 0.4266 about a centre 0.9522 below the axis","via":"user"}}],"note":"The lobe covers the takedown pin's detent spring."},"height":{"label":"End plate height (its top to its lobe's bottom)","kind":"length","measurements":[{"id":"derived","value":2.0605,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{.top_above_axis} + {.bottom_below_axis}","via":"harvest"}}]},"lobe_radius":{"label":"End plate, the radius of its lobe's round end","kind":"length","measurements":[{"id":"model","value":0.4266,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the lobe's end cylinder, r 0.4266 (#973)","via":"user"}}]},"lobe_centre_below_axis":{"label":"End plate, its lobe's round end's centre below the tube axis","kind":"length","measurements":[{"id":"model","value":0.9522,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the lobe's end cylinder's axis (#973)","via":"user"}}]},"hole_d":{"label":"End plate, its hole for the extension's thread","kind":"length","measurements":[{"id":"std","value":1.1902,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{std.receiver_extension.end_plate_hole_d}","via":"harvest"},"note":"A mil-spec plate's hole, as the reference model has it: Primary Arms' photo of the plate (40caefb1150b) is scaled by it across."}]},"key_width":{"label":"End plate, its key's width","kind":"length","measurements":[{"id":"model","value":0.125,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the key's side planes, x ±0.0625 (#1108, #1162)","via":"user"},"note":"The extension's slot it rides in is as wide (std.receiver_extension.key_slot_width)."}]},"key_tip_below_axis":{"label":"End plate, its key's tip below the tube axis","kind":"length","measurements":[{"id":"model","value":0.5619,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the key's tip plane, z 0.5619 (#1135)","via":"user"},"note":"0.012 below the extension's slot floor (std.receiver_extension.key_slot_floor, 0.55): the key stands clear of it."}]},"relief_bottom_below_axis":{"label":"End plate, the V either side of its key: its floor below the tube axis","kind":"length","measurements":[{"id":"model","value":0.6575,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the two sloped planes' lower ends, z 0.6575 (#1054, #1216), where 0.031 in rounds turn them into the key's sides","via":"user"}}]},"relief_floor_half_width":{"label":"End plate, the V either side of its key: where its sloped sides end, out from the middle","kind":"length","measurements":[{"id":"model","value":0.1119,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the sloped planes' inner ends, x ±0.1119 (#1054, #1216)","via":"user"}}]},"relief_top_half_width":{"label":"End plate, the V either side of its key: where it leaves the hole's circle, out from the middle","kind":"length","measurements":[{"id":"model","value":0.354,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the hole's cylinder ends at x ±0.3540, z 0.4784 (#1007), where the sloped planes begin","via":"user"}}]},"relief_fillet_r":{"label":"End plate, the round at the bottom of the V either side of its key, where it turns into the key's side","kind":"length","measurements":[{"id":"model","value":0.031,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"two cylinders r 0.031 at x ±0.0935, z 0.6326 (#1081, #1189)","via":"user"}}]},"edge_break":{"label":"End plate, the break on its edges","kind":"length","measurements":[{"id":"assumed","value":0.012,"unit":"in","pm":0.006,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows its edges in profile; the reference model's are sharp. A stamped plate's edges are broken a little, and a sharp edge reads as a line of light in the app.","via":"harvest"}}]},"boss_width":{"label":"End plate, its boss side to side","kind":"length","measurements":[{"id":"model","value":0.496,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"an obround: two r 0.1875 ends at x ±0.0605","via":"user"}}]},"boss_height":{"label":"End plate, its boss top to bottom","kind":"length","measurements":[{"id":"model","value":0.375,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the obround's two ends' diameter","via":"user"}}]},"boss_below_axis":{"label":"End plate, its boss's middle below the tube's axis","kind":"length","measurements":[{"id":"model","value":0.9974,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the obround's centre","via":"user"}}]},"boss_proud":{"label":"End plate, how far its boss stands out of its front face","kind":"length","measurements":[{"id":"model","value":0.0645,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the boss's face, plane y 0.1885 of a plate 0.1240 thick","via":"user"},"note":"No photo on file shows the boss in profile."}]},"dimple_depth":{"label":"End plate, the dimple in its rear face behind the boss","kind":"length","measurements":[{"id":"model","value":0.063,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"plane y 0.0630; the dimple is the boss's outline 0.005 larger all round","via":"user"},"note":"No photo on file shows the dimple in profile."}]},"dimple_grow":{"label":"End plate, how much larger all round its dimple is than its boss","kind":"length","measurements":[{"id":"model","value":0.005,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the dimple's ends r 0.1925 against the boss's r 0.1875 (#1433, #1223)","via":"user"}}]},"side_angle":{"label":"End plate, its lobe's straight sides: how far each leans in from upright","kind":"angle","measurements":[{"id":"model","value":13.5,"unit":"deg","pm":0.05,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the side planes' normals (#946, #1000: 0.972, 0.233), whose lean is atan(0.233 / 0.972)","via":"user"}}],"note":"Each side is tangent to the lobe's round end and meets the ring's circle at a corner (it isn't tangent to the ring)."},"corner_angle":{"label":"End plate, where each straight side meets the ring: its angle below the level of the tube axis","kind":"angle","measurements":[{"id":"model","value":31.33,"unit":"deg","pm":0.05,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the side planes' upper ends, x ±0.5823, 0.3545 below the axis, on the ring's r 0.6817: atan(0.3545 / 0.5823)","via":"user"}}]},"face_area":{"label":"End plate, the area its outline holds (the hole not taken out)","kind":"length","measurements":[{"id":"derived","value":2.0875,"unit":"in","pm":0.004,"source":{"type":"derived","expr":"{.top_above_axis} * {.top_above_axis} * (180 + 2 * {.corner_angle}) * 3.14159265 / 360 + {.lobe_radius} * {.lobe_radius} * (180 - 2 * {.side_angle}) * 3.14159265 / 360 + {.lobe_radius} * {.lobe_centre_below_axis} * cos({.side_angle}) + {.top_above_axis} * cos({.corner_angle}) * ({.lobe_centre_below_axis} + {.lobe_radius} * sin({.side_angle})) - {.lobe_radius} * {.top_above_axis} * cos({.side_angle}) * sin({.corner_angle})","via":"harvest"}}],"note":"In square inches, held as a length's number: the ring's arc above the two corners and the lobe's round end below its tangent points, each as a sector about its own centre, and between them the four triangles from the axis to the corners, the tangent points and the lobe's centre."},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"metal","value":0.552,"unit":"oz","pm":0.02,"source":{"type":"derived","expr":"({.face_area} - 0.785398163 * {.hole_d} * {.hole_d}) * {.thickness} * {std.density.steel}","via":"harvest"}}],"note":"No page states its weight. Worked out from its sizes: its face's area less the hole for the extension's thread, through its thickness, as steel (a mil-spec plate is steel; no page on file says what this one is made of, and its look in the photos is a steel's phosphate). The key, the V beside it and the boss move a few thousandths of a cubic inch: inside the ±."}}},{"subject":"geissele-premium-mil-spec-buffer-tube","title":"Geissele Automatics Premium Mil-Spec Buffer Tube","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"charlies","value":3.7,"unit":"oz","stated":"Weight: 3.7 oz","source":{"type":"spec","publisher":"retailer","name":"Charlie's Custom Clones, Geissele Premium Mil-Spec Buffer Tube Assembly - Gray (its SKU G081637, its markup's mpn 08-162G), the Technicals list","url":"https://charliescustomclones.com/geissele-premium-mil-spec-buffer-tube-assembly-gray/","retrieved":"2026-11-03","via":"harvest"},"note":"Said of the tube in a list that goes on \"Includes end plate and castle nut\": the tube's own weight, as the sentence the other pages share says."},{"id":"milehigh","value":3.7,"unit":"oz","stated":"This carbine-length and mil-spec-diameter Premium Buffer Tube is made in the USA and weighs in at 3.7oz","source":{"type":"spec","publisher":"retailer","name":"Mile High Shooting, Geissele: Premium MIL-SPEC Buffer Tube (08-162B)","url":"https://www.milehighshooting.com/geissele-premium-mil-spec-buffer-tube/","retrieved":"2026-11-03","via":"harvest"}},{"id":"midwest","value":3.7,"unit":"oz","stated":"This carbine length and mil-spec diameter Premium Buffer Tube is made in the USA and weighs in at 3.7oz","source":{"type":"spec","publisher":"retailer","name":"Midwest Optics, Geissele Premium Mil-Spec Buffer Tube, ODG (08-162ODG), its description","url":"https://midwestoptics.net/product/premium-mil-spec-buffer-tube-odg/","retrieved":"2026-11-03","via":"harvest"}},{"id":"midwest-data","value":8,"unit":"oz","stated":"Additional information Weight 8 oz","source":{"type":"spec","publisher":"retailer","name":"Midwest Optics, Geissele Premium Mil-Spec Buffer Tube, ODG (08-162ODG), its Additional information (and its markup's QuantitativeValue, unitCode ONZ, value 8)","url":"https://midwestoptics.net/product/premium-mil-spec-buffer-tube-odg/","retrieved":"2026-11-03","via":"harvest"},"note":"The shop's shipping weight beside its own description's 3.7: a whole number of ounces, and twice the tube."},{"id":"primary-arms","value":0.585,"unit":"lb","stated":"0.585 lbs weight","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics Premium AR-15 Buffer Tube - Carbine (08-162B), its Features list (\"Weight 0.585\" in its specifications); the DDC's page (08-162S) says the same","url":"https://www.primaryarms.com/geissele-automatics-premium-mil-spec-ar15-buffer-tube-black","retrieved":"2026-11-03","via":"harvest"},"note":"9.4 oz: more than the tube, its nut and its plate together (about 5.2 oz: the tube's 3.7 and the two steel pieces' metal worked out from their sizes); a weight as boxed."},{"id":"metal","value":3.9,"unit":"oz","pm":0.25,"source":{"type":"derived","expr":"(0.785398163 * ({.tube_od} * {.tube_od} - {std.receiver_extension.bore_d} * {std.receiver_extension.bore_d}) * {.tube_length} + 0.785398163 * {std.receiver_extension.bore_d} * {std.receiver_extension.bore_d} * {std.receiver_extension.carbine_rear_wall} + {std.receiver_extension.rail_width} * ({std.receiver_extension.rail_bottom_below_axis} - {.tube_od} / 2) * ({.tube_length} - {.rail_full_from_front}) + {std.receiver_extension.rail_width} * ({std.receiver_extension.rail_bottom_below_axis} - {.land_bottom_below_axis}) * ({.rail_full_from_front} - {.ramp_top_from_front}) / 2 + {std.receiver_extension.rail_width} * ({.land_bottom_below_axis} - {.tube_od} / 2 + 0.03) * ({.rail_full_from_front} - {.land_front_from_front}) - {.channel_width} * {.channel_depth} * 5 * {.position_step} - 6 * 0.785398163 * {.position_hole_d} * {.position_hole_d} * ({std.receiver_extension.rail_bottom_below_axis} - {.tube_od} / 2 - {.channel_depth})) * {std.density.aluminium_7075}","via":"harvest"},"note":"Worked out, not stated: the tube's wall round the drawing's bore along its length, its rear wall, its rail at full depth behind the ramp, the ramp's wedge and the strip ahead of it (from the tube's bottom, 0.03 in standing in the tube's round, to the strip's floor), less the channel and the six holes, as 7075. The thread's crests and roots are taken as the tube's own outside, and the rounds and chamfers aren't counted: the ± covers them. 0.2 oz over the sellers' 3.7, inside it."}],"adopt":{"from":"charlies","reason":"Three sellers' pages state 3.7 oz of the tube (Mile High's and Midwest Optics' in the same words), and the metal worked out from its sizes as 7075 comes to it within its ±. Primary Arms' 0.585 lb and Midwest Optics' 8 oz are weights as shipped: kept beside it."},"note":"Three sellers' pages say 3.7 oz in one sentence, the description they share (\"This carbine length and mil-spec diameter Premium Buffer Tube is made in the USA and weighs in at 3.7oz\"); Charlie's also lists it (\"Weight: 3.7 oz\"). Primary Arms' black and DDC pages give \"0.585 lbs\" (9.4 oz) and Midwest Optics' markup 8 oz: a box's weight: more than the tube with the nut and the plate its package holds (about 5.2 oz, the steel pieces' metal worked out from their sizes), and not the tube's. The tube's own metal, worked out from the sizes the model is drawn to as 7075 (\"7075-T6 aluminum\", every page), is beside them as the check the model's volume is held to."},"tube_od":{"label":"The tube's outside diameter","kind":"length","measurements":[{"id":"std","value":1.148,"unit":"in","source":{"type":"derived","expr":"{std.receiver_extension.milspec_od}","via":"harvest"},"note":"The standard mil-spec carbine tube's: every seller sells it as mil-spec."},{"id":"photo","value":1.133,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-premium-mil-spec-buffer-tube c5f8fd0417ad (Primary Arms' 08-162B_00: the black tube's right side seen level, 2200 x 1467)","scaleRef":"its own thread's pitch (std.receiver_extension.thread_pitch, 16 to the inch): 17 crests along its lower edge over 287 px, 270.1 px/in","method":"the body's top edge (row 546) above the axis, the axis midway between the thread's crests top and bottom (rows 547 and 851): 153 px, doubled. A black tube on white reads a few percent thin at its edge; the ± covers that.","via":"harvest"}}],"adopt":{"from":"std","reason":"The standard's: every seller's page says mil-spec diameter, and the photo reads it within its ± (a black tube's edge reads thin)."},"note":"Sold as mil-spec: \"Mil-spec diameter, carbine length\" (Charlie's), \"mil-spec-diameter\" (Mile High), \"6-position Mil-Spec carbine buffer tube\" (Primary Arms)."},"tube_length":{"label":"The tube's length","kind":"length","measurements":[{"id":"magpul-drawing","value":7.25,"unit":"in","pm":0.02,"stated":"7.25 (the side view's overall length; \"TWO PLACE DECIMAL .020\")","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, \"M4 Receiver Extension, Carbine, Military\" partial drawing (rev A, 2008-03-24), hosted by ar15tactical.com","url":"https://ar15tactical.com/wp-content/uploads/2016/09/ar-15-milspec-buffer-tube.pdf","retrieved":"2026-10-18","via":"harvest"},"note":"The drawing of the mil-spec carbine tube a stock maker draws its stocks to; Geissele's is sold as a mil-spec carbine tube (\"Mil-spec diameter, carbine length\")."},{"id":"photo","value":7.26,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-premium-mil-spec-buffer-tube c5f8fd0417ad (Primary Arms' 08-162B_00: the black tube's right side seen level, 2200 x 1467)","scaleRef":"its own thread's pitch (std.receiver_extension.thread_pitch, 16 to the inch): 17 crests along its lower edge between columns 1747 and 2034, 270.1 px/in, in the plane of the axis as the silhouette's ends are","method":"the silhouette's rear face (column 119) to the mouth's front face (column 2080): 1961 px","via":"harvest"}}],"adopt":{"from":"magpul-drawing","reason":"The two agree: Geissele's own tube, scaled by its own thread, is the drawing's length within 0.01 in. The drawing's figure is the finer."},"note":"No page gives it in inches (\"carbine length\", every page). Magpul's drawing of the mil-spec carbine tube, and Geissele's own black tube on Primary Arms' photo scaled by its own thread."},"tube_front_behind_pin":{"label":"The tube's front face behind the takedown pin (how far it screws in)","kind":"length","measurements":[{"id":"std","value":0.669,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"-{std.receiver_extension.front_face_x}","via":"harvest"},"note":"The Army's drawings: a mil-spec tube is screwed in until its edge stands over the buffer retainer's shoulder."}],"note":"Hidden inside the receiver: what it moves is the rail's ramp, the strip ahead of it, the channel and the six holes."},"position_step":{"label":"The stock position step","kind":"length","measurements":[{"id":"photo","value":0.658,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/geissele-premium-mil-spec-buffer-tube 47c7ff62f2dd (Primary Arms' 08-162S_02: the DDC tube's underside seen square on, 2200 x 1467)","scaleRef":"the tube's length (tube_length, 7.25 in) between its rear face (column 126) and its mouth (column 2073): 268.6 px/in","method":"the six holes' centres along the rail's middle (row 718: columns 259, 439, 616, 790, 967, 1144, the middles of each hole's dark ring), a line fitted through them: 176.7 px a step","via":"harvest"}},{"id":"magpul","value":0.66,"unit":"in","source":{"type":"derived","expr":"{magpul-moe-sl-carbine.position_step}","via":"harvest"},"note":"Magpul's MOE SL travel over a mil-spec carbine tube's six positions: what a stock on any mil-spec tube moves by."}],"adopt":{"from":"photo","reason":"Geissele's own tube; Magpul's travel for a mil-spec tube agrees within its last digit."},"note":"Six positions (\"6-position for collapsible stocks\", Charlie's; \"features 6 stock positions\", Mile High): five steps between six holes."},"position_hole_d":{"label":"The position holes' diameter (in the rail's channel)","kind":"length","measurements":[{"id":"photo","value":0.331,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-premium-mil-spec-buffer-tube 47c7ff62f2dd (Primary Arms' 08-162S_02: the DDC tube's underside seen square on)","scaleRef":"the tube's length, 268.6 px/in (position_step)","method":"the holes' dark rings along row 718: 84 to 90 px across (the rear one 214 to 304), 89 px the median","via":"harvest"}}],"note":"Each hole is as wide as the channel it is in: the channel's round ends are the rear and the front hole's rims (the DDC tube's underside, 47c7ff62f2dd; the black tube's from a little below, 40caefb1150b). Each has a small hole in its floor (31 px across, 0.115 in), not drawn."},"position_hole_rear_from_rear":{"label":"The rear position hole's centre ahead of the tube's rear face","kind":"length","measurements":[{"id":"photo","value":0.495,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-premium-mil-spec-buffer-tube 47c7ff62f2dd (Primary Arms' 08-162S_02: the DDC tube's underside seen square on)","scaleRef":"the tube's length, 268.6 px/in (position_step)","method":"the rear hole's centre (column 259) from the rear face (column 126): 133 px","via":"harvest"}}]},"channel_width":{"label":"The channel along the rail's underside, its width","kind":"length","measurements":[{"id":"photo","value":0.335,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-premium-mil-spec-buffer-tube 47c7ff62f2dd (Primary Arms' 08-162S_02: the DDC tube's underside seen square on)","scaleRef":"the tube's length, 268.6 px/in (position_step)","method":"the channel's two walls between the holes (columns 330 and 700: the dark line of its lit wall at row 671 and the step at 761): 90 px","via":"harvest"}}],"note":"A slot with round ends along the rail's bottom face, from the rear hole to the front one, the six holes in its floor (the DDC tube's underside; the black tube's three-quarter view from below, 40caefb1150b, has it as a dark slot along the rail with round ends)."},"channel_depth":{"label":"The channel along the rail's underside, its depth","kind":"length","measurements":[{"id":"assumed","value":0.05,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows the channel in section. The underside photo has its wall as a lit band 2 to 3 px wide at a lens nearly square to the floor, and the black tube's view from a little below (40caefb1150b) a dark slot: shallow next to the rail's 0.30 in.","via":"harvest"}}]},"rail_full_from_front":{"label":"The rail's ramp: where it reaches the rail's full depth, behind the tube's front face","kind":"length","measurements":[{"id":"side","value":2.897,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-premium-mil-spec-buffer-tube c5f8fd0417ad (Primary Arms' 08-162B_00: the black tube's right side seen level)","scaleRef":"its own thread's pitch, 270.1 px/in (tube_length)","method":"the silhouette's lower edge leaves the rail's bottom (row 934) at column 1297 (on a 2x crop): 783 px behind the mouth's front face (column 2080)","via":"harvest"}},{"id":"underside","value":2.867,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-premium-mil-spec-buffer-tube 47c7ff62f2dd (Primary Arms' 08-162S_02: the DDC tube's underside seen square on)","scaleRef":"the tube's length, 268.6 px/in (position_step)","method":"the ramp's lit face begins at column 1303 along row 718, 770 px behind the mouth (column 2073)","via":"harvest"}}],"adopt":{"from":"side","reason":"The silhouette: an edge against the backdrop. The underside view's lit face agrees within the two readings' ±."},"note":"Geissele's rail comes down from the strip to its full depth by a long ramp, about 30 degrees to the axis, not the drawing's 45 (std.receiver_extension.rail_ramp_start, _end: 2.326 and 2.592): both photos show it."},"ramp_top_from_front":{"label":"The rail's ramp: where it meets the strip ahead of it, behind the tube's front face","kind":"length","measurements":[{"id":"side","value":2.416,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-premium-mil-spec-buffer-tube c5f8fd0417ad (Primary Arms' 08-162B_00: the black tube's right side seen level)","scaleRef":"its own thread's pitch, 270.1 px/in (tube_length)","method":"the ramp's top end on the silhouette's lower edge, column 1427 (on a 2x crop): 653 px behind the mouth's front face","via":"harvest"}},{"id":"underside","value":2.394,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-premium-mil-spec-buffer-tube 47c7ff62f2dd (Primary Arms' 08-162S_02: the DDC tube's underside seen square on)","scaleRef":"the tube's length, 268.6 px/in (position_step)","method":"the ramp's lit face ends at column 1430 along row 718, 643 px behind the mouth","via":"harvest"}}],"adopt":{"from":"side","reason":"The silhouette; the underside view's agrees within the readings' ±."}},"land_front_from_front":{"label":"The strip the rail runs on as ahead of the ramp: its front end, behind the tube's front face","kind":"length","measurements":[{"id":"side","value":1.507,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-premium-mil-spec-buffer-tube c5f8fd0417ad (Primary Arms' 08-162B_00: the black tube's right side seen level)","scaleRef":"its own thread's pitch, 270.1 px/in (tube_length)","method":"the strip's square front end on the silhouette's lower edge, column 1673 (on a 2x crop): 407 px behind the mouth","via":"harvest"}},{"id":"underside","value":1.475,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-premium-mil-spec-buffer-tube 47c7ff62f2dd (Primary Arms' 08-162S_02: the DDC tube's underside seen square on)","scaleRef":"the tube's length, 268.6 px/in (position_step)","method":"the strip's front end, column 1677 (on a 1.5x crop), 396 px behind the mouth","via":"harvest"}}],"adopt":{"from":"side","reason":"The silhouette; the underside view's is 0.03 in ahead of it, within the two readings' ±."},"note":"Ahead of the ramp the rail goes on as a shallow strip of the rail's width under the tube to a square front end, where the plain body runs on to the thread: the black tube's side (c5f8fd0417ad) and the DDC's underside (47c7ff62f2dd), where it is the darker rectangle ahead of the ramp's lit face."},"land_bottom_below_axis":{"label":"The strip ahead of the ramp: its floor below the tube's axis","kind":"length","measurements":[{"id":"side","value":0.59,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-premium-mil-spec-buffer-tube c5f8fd0417ad (Primary Arms' 08-162B_00: the black tube's right side seen level)","scaleRef":"its own thread's pitch, 270.1 px/in (tube_length)","method":"the strip's floor (row 859) below the axis, which stands the mil-spec radius (0.574) under the body's top edge (row 546): 159 px; from the axis midway between the thread's crests, 160","via":"harvest"},"note":"0.016 in below the tube's round: the strip stands just proud of it."}]},"thread_length":{"label":"The thread's length, from the tube's front face to where its crests end","kind":"length","measurements":[{"id":"side","value":1.288,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-premium-mil-spec-buffer-tube c5f8fd0417ad (Primary Arms' 08-162B_00: the black tube's right side seen level)","scaleRef":"its own thread's pitch, 270.1 px/in (tube_length)","method":"the first crest's groove behind the plain body, column 1732 (on a 2x crop), 348 px behind the mouth; where a thread ends depends on which side it is seen from by up to a pitch","via":"harvest"}},{"id":"underside","value":1.214,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-premium-mil-spec-buffer-tube 47c7ff62f2dd (Primary Arms' 08-162S_02: the DDC tube's underside seen square on)","scaleRef":"the tube's length, 268.6 px/in (position_step)","method":"the plain body's front edge, where the first groove begins, column 1747 (on a 2x crop), 326 px behind the mouth","via":"harvest"}},{"id":"commercial-light","value":1.29,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/geissele-premium-mil-spec-buffer-tube 7564882554c6 (Charlie's Custom Clones' picture of five assemblies under one light, 3300 x 1696: the black one at the bottom, its nut turned down on its plate, the tube seen from the side)","scaleRef":"the tube's own outside diameter behind the nut, taken as the mil-spec 1.148: 208.5 px, 181.6 px/in","method":"the nut's rear face (column 2045, on a 2x crop) to the mouth (column 2270): 1.24 in, and the thread that shows behind the nut, a dark band 10 px wide (0.055): where the thread ends","via":"harvest"},"note":"A third photo, of a third tube: the nut and plate are turned on it 0.31 in further back than a lower's rear face would hold them, so all but 0.05 of the thread is under them."}],"adopt":{"from":"side","reason":"Read where the side view's silhouette shows the first groove; the underside's, a half turn round, is 0.07 in shorter: a little more than a turn of the thread's run-out, within the two readings' ± together."},"note":"Geissele's own: the mil-spec carbine tube's in the reference model is 1.181 (std.receiver_extension.thread_length). Behind the thread the plain body runs on, ahead of it a plain lip at the mouth."},"mouth_lip":{"label":"The plain lip at the mouth, ahead of the thread's first crest","kind":"length","measurements":[{"id":"side","value":0.11,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-premium-mil-spec-buffer-tube c5f8fd0417ad (Primary Arms' 08-162B_00: the black tube's right side seen level)","scaleRef":"its own thread's pitch, 270.1 px/in (tube_length)","method":"the last crest (column 2050) to the front face (2080) on the silhouette's top edge: 30 px. It stands at about the thread's roots (its top 10 px under the crests on a 2x crop)","via":"harvest"}}]},"key_slot_length":{"label":"The slot under the thread that the end plate's key rides in: its length from the tube's front face","kind":"length","measurements":[{"id":"underside","value":1,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-premium-mil-spec-buffer-tube 47c7ff62f2dd (Primary Arms' 08-162S_02: the DDC tube's underside seen square on)","scaleRef":"the tube's length, 268.6 px/in (position_step)","method":"the slot's rear end (column 1805, on a 2x crop) to the mouth (column 2073): 268 px","via":"harvest"},"note":"Shorter than the reference model's carbine tube's 1.24 (std.receiver_extension.key_slot_length): Geissele's own."}],"note":"At six o'clock, through the thread's crests (the DDC tube's underside; the black one's, 4de6884b3cf8). Its width is the standard's (std.receiver_extension.key_slot_width, 0.125): it reads 0.121 on the underside (32.5 px)."},"rear_edge_break":{"label":"The break on the tube's rear outer edge","kind":"length","measurements":[{"id":"side","value":0.06,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-premium-mil-spec-buffer-tube c5f8fd0417ad (Primary Arms' 08-162B_00: the black tube's right side seen level)","scaleRef":"its own thread's pitch, 270.1 px/in (tube_length)","method":"the silhouette's top rear corner: the top edge reaches its level (row 546) 18 px ahead of the rear face (column 119 to 137), and the rear face its full height about as far below it; drawn as a 45 degree chamfer of that size","via":"harvest"}}]},"mark_rear_from_rear":{"label":"Geissele's mark: its first line's rear end ahead of the tube's rear face","kind":"length","measurements":[{"id":"side","value":0.204,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/geissele-premium-mil-spec-buffer-tube c5f8fd0417ad (Primary Arms' 08-162B_00: the black tube's right side seen level)","scaleRef":"its own thread's pitch, 270.1 px/in (tube_length)","method":"the G's rear edge, column 174, from the rear face, column 119: 55 px","via":"harvest"}}]},"mark_length":{"label":"Geissele's mark: its first line (GEISSELE), its length","kind":"length","measurements":[{"id":"side","value":0.689,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/geissele-premium-mil-spec-buffer-tube c5f8fd0417ad (Primary Arms' 08-162B_00: the black tube's right side seen level)","scaleRef":"its own thread's pitch, 270.1 px/in (tube_length)","method":"the line's light strokes, columns 174 to 360: 186 px","via":"harvest"}}]},"mark_height":{"label":"Geissele's mark: its first line's capitals, their height","kind":"length","measurements":[{"id":"side","value":0.093,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/geissele-premium-mil-spec-buffer-tube c5f8fd0417ad (Primary Arms' 08-162B_00: the black tube's right side seen level)","scaleRef":"its own thread's pitch, 270.1 px/in (tube_length)","method":"the line's light strokes, rows 857.5 to 882.5: 25 px","via":"harvest"}}]},"mark_base_above_bottom":{"label":"Geissele's mark: its first line's foot above the rail's bottom","kind":"length","measurements":[{"id":"side","value":0.193,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/geissele-premium-mil-spec-buffer-tube c5f8fd0417ad (Primary Arms' 08-162B_00: the black tube's right side seen level)","scaleRef":"its own thread's pitch, 270.1 px/in (tube_length)","method":"the line's foot, row 882.5, above the rail's bottom, row 934.5: 52 px","via":"harvest"}}]},"mark2_rear_from_rear":{"label":"Geissele's mark: its second line's rear end ahead of the tube's rear face","kind":"length","measurements":[{"id":"side","value":0.263,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/geissele-premium-mil-spec-buffer-tube c5f8fd0417ad (Primary Arms' 08-162B_00: the black tube's right side seen level)","scaleRef":"its own thread's pitch, 270.1 px/in (tube_length)","method":"the A's rear edge, column 190, from the rear face: 71 px","via":"harvest"}}]},"mark2_length":{"label":"Geissele's mark: its second line (AUTOMATICS), its length","kind":"length","measurements":[{"id":"side","value":0.555,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/geissele-premium-mil-spec-buffer-tube c5f8fd0417ad (Primary Arms' 08-162B_00: the black tube's right side seen level)","scaleRef":"its own thread's pitch, 270.1 px/in (tube_length)","method":"the line's light strokes, columns 190 to 340: 150 px","via":"harvest"}}]},"mark2_height":{"label":"Geissele's mark: its second line's capitals, their height","kind":"length","measurements":[{"id":"side","value":0.067,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/geissele-premium-mil-spec-buffer-tube c5f8fd0417ad (Primary Arms' 08-162B_00: the black tube's right side seen level)","scaleRef":"its own thread's pitch, 270.1 px/in (tube_length)","method":"the line's light strokes, rows 896 to 914: 18 px","via":"harvest"}}]},"mark2_base_above_bottom":{"label":"Geissele's mark: its second line's foot above the rail's bottom","kind":"length","measurements":[{"id":"side","value":0.076,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/geissele-premium-mil-spec-buffer-tube c5f8fd0417ad (Primary Arms' 08-162B_00: the black tube's right side seen level)","scaleRef":"its own thread's pitch, 270.1 px/in (tube_length)","method":"the line's foot, row 914, above the rail's bottom: 20.5 px","via":"harvest"}}]},"mark_proud":{"label":"Geissele's mark: how far the model stands it off the rail's face","kind":"length","measurements":[{"id":"assumed","value":0.002,"unit":"in","pm":0.002,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: a laser mark is in the face, not on it; drawn this far proud so that its own colour shows over the face's.","via":"harvest"}}]},"mark_slant":{"label":"Geissele's mark: its letters' slant from upright","kind":"angle","measurements":[{"id":"side","value":12.7,"unit":"deg","pm":2,"source":{"type":"photo","photo":"references/geissele-premium-mil-spec-buffer-tube c5f8fd0417ad (Primary Arms' 08-162B_00: the black tube's right side seen level)","scaleRef":"none: an angle in the photo's plane","method":"the rear edges of four letters' upright strokes (E, I, L, E) in a row near the capitals' top (row 860) and one near their foot (row 880): 4 to 5 px further forward at the top over 20 rows, atan(4.5 / 20)","via":"harvest"}}]}}},{"subject":"geissele-ssa-e","title":"Geissele Automatics Super Semi-Automatic Enhanced (SSA-E) Trigger (05-160)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"aero","value":2.2,"unit":"oz","stated":"Weight(s) 2.2 oz","source":{"type":"spec","publisher":"retailer","name":"Aero Precision, Geissele Super Semi-Automatic Enhanced (SSA-E) Trigger (APRH100363), Specifications","url":"https://www.aeroprecisionusa.com/geissele-super-semi-automatic-enhanced-trigger","retrieved":"2026-10-06","via":"harvest"}},{"id":"rifleconfigurator","value":2.5,"unit":"oz","stated":"Weight 2.5 oz","source":{"type":"spec","publisher":"review","name":"Rifle Configurator (an aggregator; where its figure comes from is not stated)","url":"https://www.rifleconfigurator.com/catalog/triggers/geissele-ssa-e-trigger","retrieved":"2026-10-06","via":"harvest"}},{"id":"ar15discounts","value":3.2,"unit":"oz","stated":"Weight 3.2 oz Dimensions 2.3 × 0.9 × 2.7 in","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, Geissele Super Semi-Automatic Enhanced (SSA-E) Trigger - 05-160, Additional information","url":"https://ar15discounts.com/products/geissele-super-semi-automatic-enhanced-ssa-e-trigger/","retrieved":"2026-10-06","via":"harvest"},"note":"Beside a box of 2.3 x 0.9 x 2.7 in under the shop's 'Additional information', where a shop's software keeps what it ships by: it may be the group in its packet."}],"adopt":{"from":"aero","reason":"None is the maker's and none has a method; the three stay. Aero's is a seller's specification table for this product and the lightest: nearest the steel the model holds. The aggregator's source is unknown; AR15Discounts' sits beside a box's dimensions."},"note":"Three sellers' pages state three weights and none says what was weighed (the trigger, hammer and disconnector; with or without the two pins and three springs) or how. Others on file are packages by their size and are not entered: Selway Armory's 0.3 lbs beside 5.5 x 4 x 1.8 in, KYGunCo's 2 lb. The model's steel (trigger, hammer and disconnector, without pins and springs) is held against these in app/tests/geissele-ssa-e.test.ts."},"pin_diameter":{"label":"Pin diameter (small .154 or large .170)","kind":"length","measurements":[{"id":"primaryarms","value":0.154,"unit":"in","stated":"Standard .154\" mil-spec trigger and hammer pins fit any mil-spec stripped lower receiver","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics Super Semi-Automatic Enhanced SSA-E Two Stage AR-15 Trigger - Curved (GATSSA-E, MPN 05-160)","url":"https://www.primaryarms.com/geissele-automatics-super-semi-automatic-enhanced-ssa-e-two-stage-ar-15-trigger-.154in","retrieved":"2026-10-06","via":"harvest"}},{"id":"rifleconfigurator","value":0.154,"unit":"in","stated":"The trigger fits any Mil-Spec AR-15 lower using standard .154\" trigger and hammer pins.","source":{"type":"spec","publisher":"review","name":"Rifle Configurator (an aggregator)","url":"https://www.rifleconfigurator.com/catalog/triggers/geissele-ssa-e-trigger","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"primaryarms","reason":"A seller's page for this number (MPN 05-160); the aggregator says the same."},"note":"The two pins come with it. Sellers otherwise say only 'PIN SIZE: Mil-Spec' (Mile High, BCM, Aero)."},"pin_length":{"label":"The two pins, length","kind":"length","measurements":[{"id":"parts_view","value":0.83,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-ssa-e 1bf5dd1b0dab (BCM's 'parts view' of the SSA-E, current production: trigger, hammer and disconnector each lying on its left side on white, seen from above, with the pins and springs; 1100 x 1100)","scaleRef":"the trigger's own length across the picture, 409.8 px for the traced outline's 1.885 in (217.4 px/in), and the camera's elevation from the pieces' outlines (its sine 0.930): a pin lying 45 degrees round from the picture's level reads 0.9655 of that along itself, and its two ends' rounds add 0.26 of its diameter","method":"each pin's silhouette along its own axis (everything darker than the white ground): 183.4 and 184.2 px, less 8.7 px for the ends' rounds, over 209.9 px/in. ± covers the two pins, the elevation and a pixel at each end; the outline's own scale (± 3%) is on top of it","via":"harvest"}}],"note":"The hammer's and the trigger's pins are alike in the picture (183.4 and 184.2 px). Each has a groove at its middle and one near an end, which aren't measured. Their width in the same picture is a check of the outlines' scale: 33.0 px (± 0.8) at their full round, for the .154 in they are, where the trigger's outline is 409.8 px long: 214 px/in against the outline's own 217.4, the outline 1.4% small, give or take 2.4%."},"face_offset_x":{"label":"The shoe's face ahead of the trigger pin, at rest","kind":"length","measurements":[{"id":"photo","value":0.087,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-ssa-e 3329bf5cf26e (the SSA-E assembled and cocked, square to its right side on white (the older engraving, U.S. PAT. 7600338); the maker's artwork as Selway Armory's page serves it, 1310 x 1500)","scaleRef":"frame from the reviewed holes trigger_pin, hammer_pin (552.7 px/in, rms 0.000 in over 2 points)","method":"x_max in x [-0.3, 0.6] in y [-0.94, -0.92] of the traced outline (tools/trace.py); front edge of the bow at the exposed blade's mid-height (y -0.93: halfway between a receiver's underside at the trigger's opening, about 0.45 below the pin, and the bow's tip, 1.41 below); a curved bow, so the face there is the deepest of its curve within a few hundredths. ± covers the pins' centres (3 px each: 1% of the scale) and the rest angle (the group as pictured, its pins where a receiver has them)","via":"harvest"}}],"note":"The bow is curved: this is its front edge halfway down what shows below a receiver, near the deepest of the curve. The scale is the two pins' distance in a receiver (std.ar15: .8430 along, .3140 up); the pins' own ends read 0.149 in at it for their .154 (3% thin: dark discs on dark). Two things a receiver has check it: the body's lower front is 0.500 ahead of the pin, where a lower's trigger slot ends at .52 (std.ar15.trigger_slot_front_ahead_of_pin), and the tail's underside is 0.287 below the pin, over a pocket's floor at .3115."},"shoe_face_x":{"label":"The shoe's face ahead of the takedown pin on a mil-spec lower (derived)","kind":"length","measurements":[{"id":"derived","value":2.015,"unit":"in","source":{"type":"derived","expr":"{std.ar15.trigger_pin_x} + {.face_offset_x}","via":"harvest"}}],"note":"Length of pull is measured from here."},"shoe_width":{"label":"The shoe's width","kind":"length","measurements":[{"id":"parts_view","value":0.265,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-ssa-e 1bf5dd1b0dab (BCM's 'parts view' of the SSA-E, current production: trigger, hammer and disconnector each lying on its left side on white, seen from above, with the pins and springs; 1100 x 1100)","scaleRef":"the photo's own pose, from the trigger's traced outline (profiles.side) lying in it: its tail's end to its block's end is 409.8 px for the outline's 1.885 in (217.4 px/in, across the picture, unforeshortened), its sear's top to its bow's tip 379.9 px for 1.888 in (201.2 px/in, foreshortened by the sine of the camera's elevation: 0.926). The hammer's outline (profiles.hammer), turned 25.3 degrees to fit the box it fills there (356 x 164 px), gives 0.935, and the rim of the trigger's pin hole is an ellipse of 26.5 by 28.3 px (0.936). At 0.930 the elevation is 68.4 degrees and a width across a piece (straight up from the table, straight down the picture) reads 79.6 px/in","method":"the lit band under the bow's front edge, which is its front face seen from above, the bow's whole width down the picture: 21.2, 20.9 and 21.2 px on columns 870, 885 and 900 (from the dark right face's edge to the white ground, each at its half level). ± covers the elevation (0.926 to 0.935: 3.5% of the cosine) and half a pixel at each edge","via":"harvest"}},{"id":"three_quarter","value":0.24,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-ssa-e ab84d69b551f (BCM's '3/4 view' of the SSA-E assembled, current production, turned to show its front; 1100 x 1100)","scaleRef":"the bow's tip below the trigger pin, 1.403 in on the traced outline (388 px/in down the picture), and how far the view is turned: the trigger's right face from its tail's end to its block's front edge is 674 px for 1.864 in, 0.932 of that scale, so 21 degrees (± 3)","method":"the bow's front face, the smooth band beside its right side: 33 to 35 px across at mid-height, over 388 x sin(21 deg) = 141 px/in. ± is mostly the turn: its sine moves 14% for 3 degrees","via":"harvest"},"note":"A check, from a second picture: within its ±."}],"adopt":{"from":"parts_view","reason":"The parts view's camera is found from two outlines and a hole's rim that agree within 1%; the 3/4 view's turn is one foreshortened length. They agree within the second's ±."},"note":"The bow's width from side to side. It goes through a lower's trigger slot, .312 wide (std.ar15.trigger_slot_width); the Army's own trigger's bow is .290."},"body_width":{"label":"The body's width (the tail, across)","kind":"length","measurements":[{"id":"parts_view","value":0.25,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-ssa-e 1bf5dd1b0dab (BCM's 'parts view' of the SSA-E, current production: trigger, hammer and disconnector each lying on its left side on white, seen from above, with the pins and springs; 1100 x 1100)","scaleRef":"the photo's own pose, from the trigger's traced outline (profiles.side) lying in it: its tail's end to its block's end is 409.8 px for the outline's 1.885 in (217.4 px/in, across the picture, unforeshortened), its sear's top to its bow's tip 379.9 px for 1.888 in (201.2 px/in, foreshortened by the sine of the camera's elevation: 0.926). The hammer's outline (profiles.hammer), turned 25.3 degrees to fit the box it fills there (356 x 164 px), gives 0.935, and the rim of the trigger's pin hole is an ellipse of 26.5 by 28.3 px (0.936). At 0.930 the elevation is 68.4 degrees and a width across a piece (straight up from the table, straight down the picture) reads 79.6 px/in","method":"the lit band under the tail's lower edge, which is its underside seen from above: 19.2, 19.6, 19.6 and 19.6 px on columns 610, 650, 700 and 750 (602.6 to 622.2). ± covers the elevation and half a pixel at each edge","via":"harvest"}},{"id":"breakdown","value":0.27,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/geissele-ssa-e 86bac1cc4a94 (Primary Arms' own photograph of the SSA-E taken down, current production: the trigger with its disconnector lying on its left side, the hammer, a slave pin; 2200 x 1467)","scaleRef":"the photo's pose from four points of the tail's right face against the traced outline (its two rear corners, the step in its top, where its underside meets the bow's back): 430 px/in, the camera 62 degrees up, a width reading 150 px/in square to the tail's lower edge","method":"the band under the tail's lower edge, square to it: 46.7 px at the rear, 41.7, 38.8 and 33.8 px further forward (0.31 to 0.23 in: it narrows along the tail, which a camera this near does). The middle; ± covers the four","via":"harvest"},"note":"A check, from a second picture and a looser pose: within its ±."}],"adopt":{"from":"parts_view","reason":"The cleaner reading: a level edge on four columns, a pose checked three ways. The breakdown photo agrees within its own ±."},"note":"The tail's thickness from side to side, behind the pin. The Army's trigger's body is .290 (std.ar15.trigger_body_width)."},"block_width":{"label":"The block at the trigger's front, across","kind":"length","measurements":[{"id":"parts_view","value":0.305,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/geissele-ssa-e 1bf5dd1b0dab (BCM's 'parts view' of the SSA-E, current production: trigger, hammer and disconnector each lying on its left side on white, seen from above, with the pins and springs; 1100 x 1100)","scaleRef":"the photo's own pose, from the trigger's traced outline (profiles.side) lying in it: its tail's end to its block's end is 409.8 px for the outline's 1.885 in (217.4 px/in, across the picture, unforeshortened), its sear's top to its bow's tip 379.9 px for 1.888 in (201.2 px/in, foreshortened by the sine of the camera's elevation: 0.926). The hammer's outline (profiles.hammer), turned 25.3 degrees to fit the box it fills there (356 x 164 px), gives 0.935, and the rim of the trigger's pin hole is an ellipse of 26.5 by 28.3 px (0.936). At 0.930 the elevation is 68.4 degrees and a width across a piece (straight up from the table, straight down the picture) reads 79.6 px/in","method":"the band under the block: its far lower edge is at rows 609.4 to 612.6 on columns 945 to 985; its near lower edge, behind a lit bevel, is where the block's underside (0.077 in above the tail's by the outline) falls: row 587.1, and a dark line across the band at 585.5 on column 945 marks it. 23 to 25.5 px. ± covers both ends of that and the elevation","via":"harvest"}},{"id":"three_quarter","value":0.4,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/geissele-ssa-e ab84d69b551f (BCM's '3/4 view' of the SSA-E assembled, current production, turned to show its front; 1100 x 1100)","scaleRef":"388 px/in down the picture (the bow's tip below the pin), the view turned 21 degrees (± 3) by the right face's foreshortened length: 141 px/in across a face that looks forward","method":"the block's end as it shows beside its right face: 56 px. It takes in the bevels at the end's corners, which the turn shows as width","via":"harvest"},"note":"Larger than the parts view's by more than the two ±: the end seen from the quarter is a face and its bevels, and the turn is one foreshortened length. Kept as read."}],"adopt":{"from":"parts_view","reason":"Read where the block's own edges are told apart (a bevel, then the underside); the 3/4 view's figure takes the bevels in and rests on a turn known to 3 degrees. The disagreement stays."},"note":"The body ahead of its lower front edge (0.50 in ahead of the pin): it stands a little wider than the tail, with its lower edges bevelled. Inside a pocket .690 wide."},"boss_d":{"label":"The bosses round the trigger's pin hole, diameter","kind":"length","measurements":[{"id":"parts_view","value":0.29,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-ssa-e 1bf5dd1b0dab (BCM's 'parts view' of the SSA-E, current production: trigger, hammer and disconnector each lying on its left side on white, seen from above, with the pins and springs; 1100 x 1100)","scaleRef":"the trigger's own length across the picture: 409.8 px for the traced outline's 1.885 in (217.4 px/in; a circle lying flat keeps its diameter across the picture)","method":"the boss on the trigger's right face, from its left edge to its right: 63.3 px (columns 802.8 to 866.1). ± is 3 px: a dark round on a dark face, found by its rim's highlight","via":"harvest"}}],"note":"The Army's trigger's is .322 -.015 (std.ar15.trigger_boss_d). In the side picture the boss is under the trigger spring's coil, whose wire's inner edge is 84 px above the pin's centre where the coil hangs on it: 0.30 in across or less."},"boss_length":{"label":"The bosses round the trigger's pin hole, end to end (across)","kind":"length","measurements":[],"note":"Not read: no picture on file is square to the trigger's top or front, and in the parts view the boss's end and its foot are not told apart. What centres a trigger between a pocket's walls (.690, std.ar15.fcg_pocket_width); the Army's own are .680 (drawing 8448592). The model draws the standard's span (std.ar15.trigger_boss_length) and says so."},"hammer_width":{"label":"The hammer's width (across)","kind":"length","measurements":[{"id":"parts_view","value":0.22,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-ssa-e 1bf5dd1b0dab (BCM's 'parts view' of the SSA-E, current production: trigger, hammer and disconnector each lying on its left side on white, seen from above, with the pins and springs; 1100 x 1100)","scaleRef":"the photo's own pose, from the trigger's traced outline (profiles.side) lying in it: its tail's end to its block's end is 409.8 px for the outline's 1.885 in (217.4 px/in, across the picture, unforeshortened), its sear's top to its bow's tip 379.9 px for 1.888 in (201.2 px/in, foreshortened by the sine of the camera's elevation: 0.926). The hammer's outline (profiles.hammer), turned 25.3 degrees to fit the box it fills there (356 x 164 px), gives 0.935, and the rim of the trigger's pin hole is an ellipse of 26.5 by 28.3 px (0.936). At 0.930 the elevation is 68.4 degrees and a width across a piece (straight up from the table, straight down the picture) reads 79.6 px/in","method":"the lit band under the hammer's lower edges: 17.8, 17.8 and 17.5 px under its tail (columns 640, 670, 700), 17.9 and 18.5 under its head (490, 515). The hammer lies as the trigger does, on the same ground","via":"harvest"}},{"id":"three_quarter","value":0.21,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-ssa-e ab84d69b551f (BCM's '3/4 view' of the SSA-E assembled, current production, turned to show its front; 1100 x 1100)","scaleRef":"388 px/in down the picture, the view turned 21 degrees (± 3): 141 px/in across a face that looks forward","method":"the rim of the hammer's round end where it faces forward: 27 px, 33 with the bevel at its edge. The middle","via":"harvest"},"note":"A check: within its ±."}],"adopt":{"from":"parts_view","reason":"The parts view's camera is the better known; the two agree."},"note":"The hammer's plate from side to side. A seller-hosted sheet of the SSA's, the SSA-E's sibling on the same chassis, says 'The hammer is lighter than a standard AR15 hammer.'"},"hammer_boss_d":{"label":"The bosses round the hammer's pin hole, diameter","kind":"length","measurements":[{"id":"parts_view","value":0.25,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-ssa-e 1bf5dd1b0dab (BCM's 'parts view' of the SSA-E, current production: trigger, hammer and disconnector each lying on its left side on white, seen from above, with the pins and springs; 1100 x 1100)","scaleRef":"the trigger's own length across the picture: 217.4 px/in","method":"the boss on the hammer's right face from its left edge to its right, by the highlights of its rim: 53 px on row 715 (columns 642.5 to 695.5), 57 px at its widest in the gridded crop. ± is 4 px","via":"harvest"}}],"note":"The hammer spring's two coils sit on them. In the side picture they are under the coils (the innermost turn's inner edge is 87 px above the pin's centre: 0.31 in across or less)."},"hammer_hole_d":{"label":"The small hole through the hammer above its spring's shelf, diameter","kind":"length","measurements":[{"id":"side","value":0.078,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/geissele-ssa-e 3329bf5cf26e (the SSA-E assembled and cocked, square to its right side on white (the older engraving, U.S. PAT. 7600338); the maker's artwork as Selway Armory's page serves it, 1310 x 1500)","scaleRef":"the frame of the two pins' ends as a receiver holds them (552.7 px/in; the trigger pin's end at 655, 670.5)","method":"the hole's dark rim on a 9x crop: columns 927.8 to 971.1 (43 px), rows 341.7 to 385.6 (44 px). ± is 4 px: a soft enlargement","via":"harvest"}},{"id":"parts_view","value":0.072,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/geissele-ssa-e 1bf5dd1b0dab (BCM's 'parts view' of the SSA-E, current production: trigger, hammer and disconnector each lying on its left side on white, seen from above, with the pins and springs; 1100 x 1100)","scaleRef":"the trigger's own length across the picture: 409.8 px for the traced outline's 1.885 in (217.4 px/in; a circle lying flat keeps its diameter across the picture)","method":"the hole in the hammer's right face from side to side on a 16x crop: 15.6 px (columns 585 to 600.6). ± is 1.5 px","via":"harvest"}}],"adopt":{"from":"side","reason":"The larger picture of it, square on; the current production's reads the same within either's ±."},"note":"Through the hammer's plate between its shelf and its pin, in both productions' pictures; the older side picture shows something bright in it (a pin's end, by its look). What it is for isn't said on any page."},"hammer_hole_x":{"label":"The small hole through the hammer, ahead of the trigger pin (cocked)","kind":"length","measurements":[{"id":"side","value":0.533,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/geissele-ssa-e 3329bf5cf26e (the SSA-E assembled and cocked, square to its right side on white (the older engraving, U.S. PAT. 7600338); the maker's artwork as Selway Armory's page serves it, 1310 x 1500)","scaleRef":"the frame of the two pins' ends as a receiver holds them (552.7 px/in; the trigger pin's end at 655, 670.5)","method":"the middle of the hole's rim: column 949.5. ± is 3 px","via":"harvest"}}]},"hammer_hole_y":{"label":"The small hole through the hammer, above the trigger pin (cocked)","kind":"length","measurements":[{"id":"side","value":0.555,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/geissele-ssa-e 3329bf5cf26e (the SSA-E assembled and cocked, square to its right side on white (the older engraving, U.S. PAT. 7600338); the maker's artwork as Selway Armory's page serves it, 1310 x 1500)","scaleRef":"the frame of the two pins' ends as a receiver holds them (552.7 px/in; the trigger pin's end at 655, 670.5)","method":"the middle of the hole's rim: row 363.6. ± is 3 px","via":"harvest"}}]},"hammer_boss_length":{"label":"The bosses round the hammer's pin hole, end to end (across)","kind":"length","measurements":[],"note":"Not read, for the same want of a view as the trigger's. They and the spring's coils on them go between a pocket's walls (.690). The model draws the standard trigger's span and says so."},"disconnector_width":{"label":"The disconnector's thickness (across)","kind":"length","measurements":[{"id":"parts_view","value":0.17,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-ssa-e 1bf5dd1b0dab (BCM's 'parts view' of the SSA-E, current production: trigger, hammer and disconnector each lying on its left side on white, seen from above, with the pins and springs; 1100 x 1100)","scaleRef":"the photo's own pose, from the trigger's traced outline (profiles.side) lying in it: its tail's end to its block's end is 409.8 px for the outline's 1.885 in (217.4 px/in, across the picture, unforeshortened), its sear's top to its bow's tip 379.9 px for 1.888 in (201.2 px/in, foreshortened by the sine of the camera's elevation: 0.926). The hammer's outline (profiles.hammer), turned 25.3 degrees to fit the box it fills there (356 x 164 px), gives 0.935, and the rim of the trigger's pin hole is an ellipse of 26.5 by 28.3 px (0.936). At 0.930 the elevation is 68.4 degrees and a width across a piece (straight up from the table, straight down the picture) reads 79.6 px/in","method":"the lit band under the disconnector's lower edges, lying apart from the trigger on the same ground: 14.1 and 14.0 px (columns 650, 680), 12.6 and 12.4 px (745, 755). The middle; ± covers the four and the elevation","via":"harvest"}}],"note":"A plate. It lies over the tail's top: its spring shows from the side between the two (the side picture), so the tail has no wall beside it there."}}},{"subject":"geissele-super-42-h1","title":"Geissele Super 42 spring and H1 buffer","dimensions":{"buffer_weight":{"label":"The buffer's weight","kind":"mass","measurements":[{"id":"blowback9","value":3.78,"unit":"oz","pm":0.02,"stated":"H1 weight: 3.78oz.","source":{"type":"spec","publisher":"review","name":"Blowback9, Geissele Super 42 (an owner's write-up of an H1 kit he bought; his own measurements, no instrument named)","url":"https://blowback9.wordpress.com/2023/05/02/geissele-super-42/","retrieved":"2026-10-12","via":"harvest"}},{"id":"primary-arms","value":4,"unit":"oz","pm":0.5,"stated":"Buffer H1 Carbine Platform AR-15 Weight 4 oz.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics Super 42 AR-15 H1 Buffer With Braided Wire Spring - Carbine","url":"https://www.primaryarms.com/geissele-automatics-super-42-braided-buffer-spring-and-buffer","retrieved":"2026-10-12","via":"harvest"},"note":"A figure to the ounce, of what isn't said."}],"adopt":{"from":"blowback9","reason":"Weighed, on a kit he bought; the seller's figure is to the ounce and holds it. One tungsten weight and two steel, as a standard H buffer (the maker's weight sheet: \"H1 Buffer: T S S\"), which BCM states at 3.8 oz."}},"spring_weight":{"label":"The spring's weight","kind":"mass","measurements":[{"id":"blowback9","value":1.64,"unit":"oz","pm":0.02,"stated":"Weight: 1.64oz.","source":{"type":"spec","publisher":"review","name":"Blowback9, Geissele Super 42 (an owner's write-up of an H1 kit he bought; his own measurements, no instrument named)","url":"https://blowback9.wordpress.com/2023/05/02/geissele-super-42/","retrieved":"2026-10-12","via":"harvest"},"note":"The spring as drawn (three strands of 0.045 wire, 26 coils) holds 1.6 oz of steel."}]},"weight":{"label":"Weight (the buffer and the spring together)","kind":"mass","measurements":[{"id":"sum","value":5.42,"unit":"oz","pm":0.03,"source":{"type":"derived","expr":"{.buffer_weight} + {.spring_weight}","via":"harvest"},"note":"No page states the two together unpacked. AR15Discounts' 7.04 oz and MidwayUSA's 0.415 lb are the product as shipped."}]},"length":{"label":"The buffer's length (the head's front face to the bumper's end)","kind":"length","measurements":[{"id":"std","value":3.251,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.carbine_buffer.length}","via":"harvest"}},{"id":"blowback9","value":3.427,"unit":"in","pm":0.005,"stated":"Length: 3.427″ (same as normal buffer)","source":{"type":"spec","publisher":"review","name":"Blowback9, Geissele Super 42 (an owner's write-up of an H1 kit he bought; his own measurements, no instrument named)","url":"https://blowback9.wordpress.com/2023/05/02/geissele-super-42/","retrieved":"2026-10-12","via":"harvest"}}],"adopt":{"from":"std","reason":"He says it is a normal buffer's length, and a normal carbine buffer is 3.251 by the Army's drawings and the reference model. What his 3.427 spans isn't said (a bumper standing further out of one body would do it), and it is drawn as the buffer it is said to be the same as."}},"od":{"label":"The buffer's diameter (its head, which runs in the extension's bore)","kind":"length","measurements":[{"id":"std","value":0.98,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.carbine_buffer.head_d}","via":"harvest"}}]},"shoulder_d":{"label":"The buffer's shoulder behind its head, which the spring's end coil sits over","kind":"length","measurements":[{"id":"blowback9","value":0.762,"unit":"in","pm":0.002,"stated":"“Collar” diameter: 0.762″ (normal buffer = 0.781″)","source":{"type":"spec","publisher":"review","name":"Blowback9, Geissele Super 42 (an owner's write-up of an H1 kit he bought; his own measurements, no instrument named)","url":"https://blowback9.wordpress.com/2023/05/02/geissele-super-42/","retrieved":"2026-10-12","via":"harvest"}},{"id":"forum","value":0.7525,"unit":"in","pm":0.002,"stated":"Geissele AR 15 Carbine 10 7/8\" 27 0.6845\" 0.7525\" Std AR 15 Carbine 10 1/2 \" 38 0.6835\" 0.7765\"","source":{"type":"spec","publisher":"forum","name":"survivalshop, 308AR.com forum, 21 Aug 2016: a table of his own measurements, the Geissele beside a standard carbine spring and buffer","url":"https://forum.308ar.com/topic/13358-geissele-super-42-braided-spring-buffer-combo/","retrieved":"2026-10-12","via":"harvest"},"note":"The table's last column, \"buffer spring shoulder\"."},{"id":"patent","value":0.76,"unit":"in","pm":0.005,"stated":"diameter D1 is 0.76 inch. Notably, a standard buffer has a shoulder diameter of about 0.78 inch.","source":{"type":"spec","publisher":"manufacturer","name":"US 9,829,260 B2, 'Buffer and spring assembly for a firearm' (WHG Properties, LLC; W. H. Geissele, K. Cannon): the description's example. The patent office's PDF has no text layer: read from its pages as pictures","url":"https://image-ppubs.uspto.gov/dirsearch-public/print/downloadPdf/9829260","retrieved":"2026-10-12","via":"harvest"},"note":"The maker's own patent; no marking page on file ties its number to the product, so its figures are an example's. They hang together with the product where it can be checked: its 0.76 shoulder is the 0.762 an owner measured."}],"adopt":{"from":"blowback9","reason":"Measured on the product, and the maker's patent has the same to the hundredth; the forum's is a hundredth under both, of a unit seven years older."},"note":"What makes this buffer the spring's own. Geissele, on AR15.com: \"We had to make the shoulder slightly smaller because of the braided wire design being 'thicker' than a single piece.\" A standard buffer's is 0.781."},"body_d":{"label":"The buffer's body diameter","kind":"length","measurements":[{"id":"blowback9","value":0.687,"unit":"in","pm":0.002,"stated":"Body diameter: 0.687″ (same as normal buffer)","source":{"type":"spec","publisher":"review","name":"Blowback9, Geissele Super 42 (an owner's write-up of an H1 kit he bought; his own measurements, no instrument named)","url":"https://blowback9.wordpress.com/2023/05/02/geissele-super-42/","retrieved":"2026-10-12","via":"harvest"}},{"id":"forum","value":0.6845,"unit":"in","pm":0.002,"stated":"0.6845\"","source":{"type":"spec","publisher":"forum","name":"survivalshop, 308AR.com forum, 21 Aug 2016: a table of his own measurements, the Geissele beside a standard carbine spring and buffer","url":"https://forum.308ar.com/topic/13358-geissele-super-42-braided-spring-buffer-combo/","retrieved":"2026-10-12","via":"harvest"},"note":"The table's \"buffer main body\" column; his standard buffer reads 0.6835 beside it."}],"adopt":{"from":"blowback9","reason":"The standard's own figure (std.carbine_buffer.body_d), which he says it is the same as; the forum's two bodies are a thousandth apart, 0.003 under it."}},"strands":{"label":"The spring's wire, how many strands","kind":"count","measurements":[{"id":"sheet","value":3,"unit":"count","stated":"Its unique spring design uses three independent strands of wire, just like the German MG42 Machine Gun.","source":{"type":"spec","publisher":"manufacturer","name":"Geissele Automatics, Super 42 Braided Buffer Spring and Buffer Combo instructions (the maker's sheet, as a seller hosts it)","url":"https://cdn.shopify.com/s/files/1/1271/7541/files/Super_42_Braided_Buffer_Spring_and_Buffer_Combo_Instructions_1.pdf","retrieved":"2026-10-12","via":"harvest"}}]},"strand_d":{"label":"The spring's wire, one strand's diameter","kind":"length","measurements":[{"id":"patent","value":0.045,"unit":"in","pm":0.0005,"stated":"0.045 inch diameter steel music wire","source":{"type":"spec","publisher":"manufacturer","name":"US 9,829,260 B2, 'Buffer and spring assembly for a firearm' (WHG Properties, LLC; W. H. Geissele, K. Cannon): the description's example. The patent office's PDF has no text layer: read from its pages as pictures","url":"https://image-ppubs.uspto.gov/dirsearch-public/print/downloadPdf/9829260","retrieved":"2026-10-12","via":"harvest"},"note":"The maker's own patent; no marking page on file ties its number to the product, so its figures are an example's. They hang together with the product where it can be checked: its 0.76 shoulder is the 0.762 an owner measured. Three such strands laid together like a rope are 0.097 in across, and 26 coils of them weigh 1.6 oz: the owner's measured 1.64."}]},"twist_pitch":{"label":"The spring's wire, the length in which its strands turn once about each other","kind":"length","measurements":[{"id":"patent","value":0.475,"unit":"in","pm":0.005,"stated":"twist pitch of 0.475 inch","source":{"type":"spec","publisher":"manufacturer","name":"US 9,829,260 B2, 'Buffer and spring assembly for a firearm' (WHG Properties, LLC; W. H. Geissele, K. Cannon): the description's example. The patent office's PDF has no text layer: read from its pages as pictures","url":"https://image-ppubs.uspto.gov/dirsearch-public/print/downloadPdf/9829260","retrieved":"2026-10-12","via":"harvest"},"note":"The maker's own patent; no marking page on file ties its number to the product, so its figures are an example's. They hang together with the product where it can be checked: its 0.76 shoulder is the 0.762 an owner measured. (\"or ... 2.1 twists per inch\", the same.)"}]},"stranded_thickness":{"label":"The spring's wire across all its strands","kind":"length","measurements":[{"id":"strands","value":0.097,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{.strand_d} * 2.1547","via":"harvest"},"note":"Three round strands lying against each other: the circle round them is 1 + 2/√3 of one's diameter."},{"id":"blowback9","value":0.105,"unit":"in","pm":0.003,"stated":"Combined wire strands measured diameter: 0.105″","source":{"type":"spec","publisher":"review","name":"Blowback9, Geissele Super 42 (an owner's write-up of an H1 kit he bought; his own measurements, no instrument named)","url":"https://blowback9.wordpress.com/2023/05/02/geissele-super-42/","retrieved":"2026-10-12","via":"harvest"}}],"adopt":{"from":"strands","reason":"What three strands of the patent's wire come to. An owner's jaws across a rope read 0.008 more: with his own outside diameter that leaves 0.700 inside, which wouldn't go over the 0.762 shoulder he measured on the buffer it is sold seated on."}},"spring_od":{"label":"The spring's outside diameter","kind":"length","measurements":[{"id":"patent","value":0.95,"unit":"in","pm":0.005,"stated":"outside diameter D3 of 0.95 inch","source":{"type":"spec","publisher":"manufacturer","name":"US 9,829,260 B2, 'Buffer and spring assembly for a firearm' (WHG Properties, LLC; W. H. Geissele, K. Cannon): the description's example. The patent office's PDF has no text layer: read from its pages as pictures","url":"https://image-ppubs.uspto.gov/dirsearch-public/print/downloadPdf/9829260","retrieved":"2026-10-12","via":"harvest"},"note":"The maker's own patent; no marking page on file ties its number to the product, so its figures are an example's. They hang together with the product where it can be checked: its 0.76 shoulder is the 0.762 an owner measured. With its wire 0.097 across, 0.756 inside: on the 0.76 shoulder, as a spring that stays on its buffer is."},{"id":"blowback9","value":0.91,"unit":"in","pm":0.005,"stated":"Outer diameter: 0.910″","source":{"type":"spec","publisher":"review","name":"Blowback9, Geissele Super 42 (an owner's write-up of an H1 kit he bought; his own measurements, no instrument named)","url":"https://blowback9.wordpress.com/2023/05/02/geissele-super-42/","retrieved":"2026-10-12","via":"harvest"},"note":"Seller's side photo (bd3cd61e3456) has the spring 0.89 to 0.94 across by the buffer under it, which may not be at one scale with it."}],"adopt":{"from":"patent","reason":"What it has to fit decides: the spring is sold seated on a buffer whose shoulder is 0.762 (Primary Arms' photo of the two together), and 0.91 outside less the wire twice is 0.70 to 0.72 inside, which doesn't go over it. The patent's 0.95 does, and is inside the extension's inch."}},"coils":{"label":"The spring's coils, end to end","kind":"count","measurements":[{"id":"photo","value":26,"unit":"count","pm":1,"source":{"type":"photo","photo":"references/geissele-super-42-h1 bd3cd61e3456 (Midwest Gun Works, 1500 px: the kit's spring square to its side on white, the buffer under it)","scaleRef":"none: a count","method":"the crests of its outline along each side, 26 on one and 25 on the other (.cache/buffer/spring/crests.py)","via":"harvest"}},{"id":"forum","value":27,"unit":"count","stated":"Geissele AR 15 Carbine 10 7/8\" 27","source":{"type":"spec","publisher":"forum","name":"survivalshop, 308AR.com forum, 21 Aug 2016: a table of his own measurements, the Geissele beside a standard carbine spring and buffer","url":"https://forum.308ar.com/topic/13358-geissele-super-42-braided-spring-buffer-combo/","retrieved":"2026-10-12","via":"harvest"}}],"adopt":{"from":"photo","reason":"Counted, on both sides of the silhouette; an owner's 27 is inside its ±, and another's \"Active coils: 23.5\" is the same spring less its closed ends."}},"free_length":{"label":"The spring's length out of the rifle","kind":"length","measurements":[{"id":"blowback9","value":11.125,"unit":"in","pm":0.06,"stated":"Length uncompressed: 11.125″","source":{"type":"spec","publisher":"review","name":"Blowback9, Geissele Super 42 (an owner's write-up of an H1 kit he bought; his own measurements, no instrument named)","url":"https://blowback9.wordpress.com/2023/05/02/geissele-super-42/","retrieved":"2026-10-12","via":"harvest"}},{"id":"forum","value":10.875,"unit":"in","pm":0.06,"stated":"10 7/8\"","source":{"type":"spec","publisher":"forum","name":"survivalshop, 308AR.com forum, 21 Aug 2016: a table of his own measurements, the Geissele beside a standard carbine spring and buffer","url":"https://forum.308ar.com/topic/13358-geissele-super-42-braided-spring-buffer-combo/","retrieved":"2026-10-12","via":"harvest"}},{"id":"patent","value":11,"unit":"in","pm":0.5,"stated":"a free length of 11 inches and 24.5 active coils","source":{"type":"spec","publisher":"manufacturer","name":"US 9,829,260 B2, 'Buffer and spring assembly for a firearm' (WHG Properties, LLC; W. H. Geissele, K. Cannon): the description's example. The patent office's PDF has no text layer: read from its pages as pictures","url":"https://image-ppubs.uspto.gov/dirsearch-public/print/downloadPdf/9829260","retrieved":"2026-10-12","via":"harvest"},"note":"The maker's own patent; no marking page on file ties its number to the product, so its figures are an example's. They hang together with the product where it can be checked: its 0.76 shoulder is the 0.762 an owner measured."}],"adopt":{"from":"blowback9","reason":"The later of two owners' measurements, a quarter of an inch apart, of two springs seven years apart; the patent's example is between them. Not drawn: the model is the spring as installed."}},"installed_length":{"label":"The spring's length as installed (the buffer's seat to a mil-spec carbine extension's rear wall, bolt forward)","kind":"length","measurements":[{"id":"room","value":6.972,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{bcm-carbine-action-spring.installed_length}","via":"harvest"},"note":"The room a carbine spring has, whichever spring it is. The patent's example has 6.74 in for it."}]}}},{"subject":"geissele-super-42-h2","title":"Geissele Super 42 spring and H2 buffer","dimensions":{"buffer_weight":{"label":"The buffer's weight","kind":"mass","measurements":[{"id":"forum","value":4.33,"unit":"oz","pm":0.02,"stated":"My milspec h2 buffer weights 4.6-4.7 oz my G h2 buffer weights 4.33 oz","source":{"type":"spec","publisher":"forum","name":"A poster on AR15.com, 20 May 2019, 'Geissele Super 42 Weight Question': his own weighing of the two, no instrument named","url":"https://www.ar15.com/forums/AR-15/Geissele-Super-42-Weight-Question/118-740310/","retrieved":"2026-10-12","via":"harvest"}},{"id":"primary-arms","value":4.6,"unit":"oz","pm":0.05,"stated":"Buffer H2 Carbine Platform AR-15 Weight 4.6 oz.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics Super 42 AR-15 H2 Buffer With Braided Wire Spring - Carbine","url":"https://www.primaryarms.com/geissele-automatics-super-42-braided-buffer-spring-and-h2-buffer","retrieved":"2026-10-12","via":"harvest"},"note":"A standard H2 buffer's figure (BCM states its own at 4.6)."}],"adopt":{"from":"forum","reason":"Weighed, beside a standard H2 on the same scale that read what a standard H2 is said to weigh. The seller's 4.6 is the standard's figure; the same seller has this maker's H3 at 4.85, which is one more tungsten weight over 4.33 and not over 4.6 (the H1 was weighed at 3.78: steps of 0.55). Two tungsten weights and one steel (the maker's weight sheet: \"H2 Buffer: T T S\")."}},"weight":{"label":"Weight (the buffer and the spring together)","kind":"mass","measurements":[{"id":"sum","value":5.97,"unit":"oz","pm":0.06,"source":{"type":"derived","expr":"{.buffer_weight} + {geissele-super-42-h1.spring_weight}","via":"harvest"},"note":"The spring is the one an owner weighed out of an H1 set: the three sets are sold with the same spring."}]},"length":{"label":"The buffer's length (the head's front face to the bumper's end)","kind":"length","measurements":[{"id":"std","value":3.251,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.carbine_buffer.length}","via":"harvest"}}]},"od":{"label":"The buffer's diameter (its head, which runs in the extension's bore)","kind":"length","measurements":[{"id":"std","value":0.98,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.carbine_buffer.head_d}","via":"harvest"}}]}}},{"subject":"geissele-super-42-h3","title":"Geissele Super 42 spring and H3 buffer","dimensions":{"buffer_weight":{"label":"The buffer's weight","kind":"mass","measurements":[{"id":"primary-arms","value":4.85,"unit":"oz","pm":0.05,"stated":"Buffer H3 Carbine Platform AR-15 Weight 4.85 oz.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics Super 42 AR-15 H3 Buffer With Braided Wire Spring - Carbine","url":"https://www.primaryarms.com/geissele-automatics-super-42-braided-buffer-spring-and-h3-buffer","retrieved":"2026-10-12","via":"harvest"}},{"id":"alexanders","value":5.4,"unit":"oz","pm":0.2,"stated":"Buffer Weight: H3 (approx. 5.4 oz)","source":{"type":"spec","publisher":"retailer","name":"Alexander's Store, Geissele SPR 42 BRD Wire BFR SPR H3 (05-495-H3)","url":"https://alexandersstore.com/product/geissele-spr-42-brd-wire-bfr-spr-h3/","retrieved":"2026-10-12","via":"harvest"},"note":"A standard H3 buffer's figure (BCM states its own at 5.4), given as approximate."}],"adopt":{"from":"primary-arms","reason":"Nobody on file has weighed one. Primary Arms' 4.85 is a figure of this buffer's own (a standard H3 is 5.4), and it is what the two that were weighed lead to: 3.78 for the H1, 4.33 for the H2, a step of 0.55 for each steel weight changed for tungsten. Three tungsten weights (the maker's weight sheet: \"H3 Buffer: T T T\")."}},"weight":{"label":"Weight (the buffer and the spring together)","kind":"mass","measurements":[{"id":"sum","value":6.49,"unit":"oz","pm":0.06,"source":{"type":"derived","expr":"{.buffer_weight} + {geissele-super-42-h1.spring_weight}","via":"harvest"},"note":"The spring is the one an owner weighed out of an H1 set: the three sets are sold with the same spring."}]},"length":{"label":"The buffer's length (the head's front face to the bumper's end)","kind":"length","measurements":[{"id":"std","value":3.251,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.carbine_buffer.length}","via":"harvest"}}]},"od":{"label":"The buffer's diameter (its head, which runs in the extension's bore)","kind":"length","measurements":[{"id":"std","value":0.98,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.carbine_buffer.head_d}","via":"harvest"}}]}}},{"subject":"geissele-super-duty-stripped-lower","title":"Geissele Automatics Super Duty AR-15 Lower Receiver - Stripped Lower (05-2994-B)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"metal","value":8.384,"unit":"oz","pm":0.84,"source":{"type":"derived","basis":"This part's own model's metal: the closed volume of app/public/models/geissele-super-duty-stripped-lower.glb as its script built it (5.1372 cubic inches: the traced outline at the Army drawing's widths, its pocket, well, bore and holes cut, the rib and the pads on; the manifest's volume_in3) times what a cubic inch of 7075 weighs (std.density.aluminium_7075, 1.632 oz): 5.1372 x 1.632 = 8.384 oz. Primary Arms: 'Precision machined from 7075-T6 aluminum'.","via":"harvest"}}],"note":"WORKED OUT, not published: no page read states a weight (Primary Arms' two pages, Blackstone's two, Aegis Cerakote's; Blackstone's markup has \"weight\":null), and geissele.com refuses the reader. The ± is a tenth: what a model with its inside edges square, its thread uncut, the rib's and the pads' heights assumed can be off by. app/tests/geissele-super-duty-stripped-lower.test.ts holds the model's volume to this figure."},"width":{"label":"Receiver maximum width (Z)","kind":"length","measurements":[{"id":"std","value":0.88,"unit":"in","pm":0.008,"source":{"type":"derived","expr":"{std.ar15.lower_body_width}","via":"harvest"},"note":"The body's width is the Army drawing's (8448608): Primary Arms, of this lower: 'Precision machined from 7075-T6 aluminum to mil-spec dimensions', 'Compatible with mil-spec AR-15 components', 'any mil-spec lower parts kit and components drop right in without modification'. No page states a width and no photo on file looks along the receiver."}],"note":"The body's is the drawing's; the well's walls (std.ar15.magwell_outside_width) and the tower's ring (std.ar15.buffer_tower_od) stand wider and are drawn at the drawing's too; the roll along the top of the well's right wall is the widest thing on the receiver (well_roll_crest_out)."},"buffer_axis_above_pin":{"label":"Receiver extension (bore) axis above the takedown pin centre","kind":"length","measurements":[{"id":"std","value":0.8775,"unit":"in","pm":0.0015,"source":{"type":"derived","expr":"{std.ar15.bore_axis_y}","via":"harvest"},"note":"A mil-spec lower by its seller's sentence: the threaded hole's centre is the drawing's. The rectified right photo's ring tops out at 1.575, the drawing's 1.5735 (tower_top_above_pin)."}]},"magazine_seat_x":{"label":"Magazine seat, X (a seated magazine's frame origin ahead of the takedown pin)","kind":"length","measurements":[{"id":"milspec","value":3.4915,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{bad-workhorse-lower.magazine_seat_x}","via":"user"},"note":"Where a magazine seats in a mil-spec well: from the Army drawing's well and catch slot and the user's own magazine, recorded on the Workhorse. Primary Arms, of this lower: 'Precision machined from 7075-T6 aluminum to mil-spec dimensions', 'Compatible with mil-spec AR-15 components', 'any mil-spec lower parts kit and components drop right in without modification'; the rectified right photo has the catch's hole and the button's pocket where the drawing puts them (the pocket 0.50 tall about Y -0.56, the drawing's .515 about -0.565). No photo of a magazine seated in it is on file."}]},"magazine_seat_y":{"label":"Magazine seat, Y (the feed-lip top of a seated magazine)","kind":"length","measurements":[{"id":"milspec","value":1.003,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{bad-workhorse-lower.magazine_seat_y}","via":"user"},"note":"As magazine_seat_x: the standard well's and the catch's, not this receiver's outside."}]},"grip_mating_y":{"label":"Receiver underside behind the step (where a grip's flat top bears), Y","kind":"length","measurements":[{"id":"right","value":-1.065,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower efc0b44358f7 (right side: Primary Arms' photo ddfadb3e24e2 (05-2994-B_05) laid square onto the right face by the drawing's holes, the far wall's share taken off)","scaleRef":"frame from the reviewed holes takedown, pivot (200.0 px/in, rms 0.000 in over 2 points)","method":"y_min in x [-0.25, -0.1] of the traced outline (tools/trace.py)","via":"harvest"},"note":"The outline's flat just behind the lug's step: the right face's reading of where a grip's flat top bears (the seat itself is the drawing's: grip_seat_y)."}],"note":"The outline's flat just behind the lug's rear face: the right side's reading of where a grip's flat top bears. The seat itself is the drawing's (grip_seat_y)."},"grip_seat_y":{"label":"Grip seat, Y (the underside a grip's flat top bears on, at the takedown pin's X)","kind":"length","measurements":[{"id":"tdp","value":-1.0695,"unit":"in","pm":0.0115,"source":{"type":"derived","expr":"{std.ar15.deck_y} - {std.ar15.grip_seat_below_deck}","via":"harvest"},"note":"A mil-spec lower: the flat the lug hangs from is the drawing's, 1.318 ±.010 below the deck."},{"id":"right","value":-1.065,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower efc0b44358f7 (right side: Primary Arms' photo ddfadb3e24e2, 05-2994-B_05, laid square onto the right face at 200 px/in by a homography fitted to the near rims of the Army drawing's six holes on it, each within 0.0034 in after the fit)","scaleRef":"the rectification's frame: takedown pin (319.5, 399.5), pivot (1594.5, 399.5) px, 200 px/in (.cache/batch15/geissele-super-duty-stripped-lower/rect.py in the main checkout, holes.py beside it)","method":"y_min of the traced outline in x [-0.25, -0.1]: the flat just behind the lug's step","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing dimensions it, and the rectified right photo has the flat behind the lug 0.005 above it."}},"grip_shelf_top_x":{"label":"Grip shelf start (the step behind the grip: the lug's rear face), X","kind":"length","measurements":[{"id":"right","value":-0.06,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower efc0b44358f7 (right side: Primary Arms' photo ddfadb3e24e2 (05-2994-B_05) laid square onto the right face by the drawing's holes, the far wall's share taken off)","scaleRef":"frame from the reviewed holes takedown, pivot (200.0 px/in, rms 0.000 in over 2 points)","method":"x_min in x [-0.2, 0.6] in y [-1.3, -1.1] of the traced outline (tools/trace.py)","via":"harvest"},"note":"The step behind the grip (a near-upright edge between Y -1.05 and -1.32)."}],"note":"The lug's rear face as the outline has it; the drawing's is -0.075 (std.ar15.receiver_rear_x + grip_lug_front_from_rear_face - grip_lug_length), which the model uses."},"trigger_opening_top_y":{"label":"Receiver underside above the trigger opening, Y","kind":"length","measurements":[{"id":"right","value":-1.09,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower efc0b44358f7 (right side: Primary Arms' photo ddfadb3e24e2 (05-2994-B_05) laid square onto the right face by the drawing's holes, the far wall's share taken off)","scaleRef":"frame from the reviewed holes takedown, pivot (200.0 px/in, rms 0.000 in over 2 points)","method":"y_min in x [1.95, 2.85] of the traced outline (tools/trace.py)","via":"harvest"},"note":"The body's lower edge above the trigger guard's opening."}],"note":"The rectified right photo's outline: 0.02 below the grip seat's plane (-1.0695), within its ±; the model draws one plane there, as the drawing has one surface."},"trigger_guard_front_x":{"label":"Trigger guard front ear hole, X","kind":"length","measurements":[{"id":"tdp","value":3.3425,"unit":"in","pm":0.007,"source":{"type":"derived","expr":"{std.ar15.trigger_guard_front_x}","via":"harvest"},"note":"A mil-spec lower (Primary Arms, of this lower: 'Precision machined from 7075-T6 aluminum to mil-spec dimensions', 'Compatible with mil-spec AR-15 components', 'any mil-spec lower parts kit and components drop right in without modification'): the hole is the drawing's. Its hole goes into the right ear only, from its spotface; the rectified right photo shows the spotface's round at the ear where the drawing has it (not fitted: its rim is in shadow)."}]},"trigger_guard_front_y":{"label":"Trigger guard front ear hole, Y","kind":"length","measurements":[{"id":"tdp","value":-2.18,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{std.ar15.trigger_guard_rear_y}","via":"harvest"},"note":"A mil-spec lower (Primary Arms, of this lower: 'Precision machined from 7075-T6 aluminum to mil-spec dimensions', 'Compatible with mil-spec AR-15 components', 'any mil-spec lower parts kit and components drop right in without modification'): the hole is the drawing's. Its hole goes into the right ear only, from its spotface; the rectified right photo shows the spotface's round at the ear where the drawing has it (not fitted: its rim is in shadow)."}]},"trigger_guard_rear_x":{"label":"Trigger guard rear ear hole, X","kind":"length","measurements":[{"id":"tdp","value":1.4985,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{std.ar15.trigger_guard_rear_x}","via":"harvest"},"note":"A mil-spec lower (Primary Arms, of this lower: 'Precision machined from 7075-T6 aluminum to mil-spec dimensions', 'Compatible with mil-spec AR-15 components', 'any mil-spec lower parts kit and components drop right in without modification'): the hole is the drawing's. Not an independent check: it is one of the six holes the rectifications were fitted to (on the right within 0.0034 in, on the left within 0.031 after the fit), which says the photos hold the drawing's pattern of holes, not where any one is."}]},"trigger_guard_rear_y":{"label":"Trigger guard rear ear hole, Y","kind":"length","measurements":[{"id":"tdp","value":-2.18,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{std.ar15.trigger_guard_rear_y}","via":"harvest"},"note":"A mil-spec lower (Primary Arms, of this lower: 'Precision machined from 7075-T6 aluminum to mil-spec dimensions', 'Compatible with mil-spec AR-15 components', 'any mil-spec lower parts kit and components drop right in without modification'): the hole is the drawing's. Not an independent check: it is one of the six holes the rectifications were fitted to (on the right within 0.0034 in, on the left within 0.031 after the fit), which says the photos hold the drawing's pattern of holes, not where any one is."}]},"trigger_pin_x":{"label":"Trigger pin hole centre, X","kind":"length","measurements":[{"id":"tdp","value":1.928,"unit":"in","pm":0.004,"source":{"type":"derived","expr":"{std.ar15.trigger_pin_x}","via":"harvest"},"note":"A mil-spec lower (Primary Arms, of this lower: 'Precision machined from 7075-T6 aluminum to mil-spec dimensions', 'Compatible with mil-spec AR-15 components', 'any mil-spec lower parts kit and components drop right in without modification'): the hole is the drawing's. Not an independent check: it is one of the six holes the rectifications were fitted to (on the right within 0.0034 in, on the left within 0.031 after the fit), which says the photos hold the drawing's pattern of holes, not where any one is."}]},"trigger_pin_y":{"label":"Trigger pin hole centre, Y","kind":"length","measurements":[{"id":"tdp","value":-0.689,"unit":"in","pm":0.0035,"source":{"type":"derived","expr":"{std.ar15.trigger_pin_y}","via":"harvest"},"note":"A mil-spec lower (Primary Arms, of this lower: 'Precision machined from 7075-T6 aluminum to mil-spec dimensions', 'Compatible with mil-spec AR-15 components', 'any mil-spec lower parts kit and components drop right in without modification'): the hole is the drawing's. Not an independent check: it is one of the six holes the rectifications were fitted to (on the right within 0.0034 in, on the left within 0.031 after the fit), which says the photos hold the drawing's pattern of holes, not where any one is."}]},"hammer_pin_x":{"label":"Hammer pin hole centre, X","kind":"length","measurements":[{"id":"tdp","value":2.771,"unit":"in","pm":0.004,"source":{"type":"derived","expr":"{std.ar15.hammer_pin_x}","via":"harvest"},"note":"A mil-spec lower (Primary Arms, of this lower: 'Precision machined from 7075-T6 aluminum to mil-spec dimensions', 'Compatible with mil-spec AR-15 components', 'any mil-spec lower parts kit and components drop right in without modification'): the hole is the drawing's. Not an independent check: it is one of the six holes the rectifications were fitted to (on the right within 0.0034 in, on the left within 0.031 after the fit), which says the photos hold the drawing's pattern of holes, not where any one is."}]},"hammer_pin_y":{"label":"Hammer pin hole centre, Y","kind":"length","measurements":[{"id":"tdp","value":-0.375,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{std.ar15.hammer_pin_y}","via":"harvest"},"note":"A mil-spec lower (Primary Arms, of this lower: 'Precision machined from 7075-T6 aluminum to mil-spec dimensions', 'Compatible with mil-spec AR-15 components', 'any mil-spec lower parts kit and components drop right in without modification'): the hole is the drawing's. Not an independent check: it is one of the six holes the rectifications were fitted to (on the right within 0.0034 in, on the left within 0.031 after the fit), which says the photos hold the drawing's pattern of holes, not where any one is."}]},"selector_x":{"label":"Safety selector hole centre, X","kind":"length","measurements":[{"id":"tdp","value":0.803,"unit":"in","pm":0.004,"source":{"type":"derived","expr":"{std.ar15.selector_x}","via":"harvest"},"note":"A mil-spec lower (Primary Arms, of this lower: 'Precision machined from 7075-T6 aluminum to mil-spec dimensions', 'Compatible with mil-spec AR-15 components', 'any mil-spec lower parts kit and components drop right in without modification'): the hole is the drawing's. Not an independent check: it is one of the six holes the rectifications were fitted to (on the right within 0.0034 in, on the left within 0.031 after the fit), which says the photos hold the drawing's pattern of holes, not where any one is."}]},"selector_y":{"label":"Safety selector hole centre, Y","kind":"length","measurements":[{"id":"tdp","value":-0.466,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{std.ar15.selector_y}","via":"harvest"},"note":"A mil-spec lower (Primary Arms, of this lower: 'Precision machined from 7075-T6 aluminum to mil-spec dimensions', 'Compatible with mil-spec AR-15 components', 'any mil-spec lower parts kit and components drop right in without modification'): the hole is the drawing's. Not an independent check: it is one of the six holes the rectifications were fitted to (on the right within 0.0034 in, on the left within 0.031 after the fit), which says the photos hold the drawing's pattern of holes, not where any one is."}]},"fcg_pin_hole_d":{"label":"Hammer and trigger pin holes, diameter","kind":"length","measurements":[{"id":"tdp","value":0.15675,"unit":"in","pm":0.00075,"source":{"type":"derived","expr":"{std.ar15.fcg_pin_hole_d}","via":"harvest"},"note":"A mil-spec lower: the drawing's holes for the .154 pins (fcg_pin_d, the page's)."}]},"fcg_pin_d":{"label":"Hammer and trigger pins it takes, diameter","kind":"length","measurements":[{"id":"page","value":0.154,"unit":"in","pm":0.0005,"stated":"Trigger Pin Diameter MIL-SPEC .154","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics Super Duty AR-15 Lower Receiver - Stripped Lower (05-2994-B), Specifications","url":"https://www.primaryarms.com/geissele-automatics-super-duty-stripped-ar-15-lower-stripped-lower","retrieved":"2026-10-28","via":"harvest"},"note":"The pins' size (small-pin), which the fcg interface's pin_diameter states; the holes are the drawing's (fcg_pin_hole_d)."}]},"takedown_hole_d":{"label":"Takedown and pivot pin holes, diameter","kind":"length","measurements":[{"id":"tdp","value":0.251,"unit":"in","pm":0.001,"source":{"type":"derived","expr":"{std.ar15.takedown_hole_d}","via":"harvest"},"note":"The Army drawing's hole."},{"id":"page","value":0.25,"unit":"in","pm":0.0005,"stated":".250\" takedown holes","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics Super Duty AR-15 Lower Receiver - Stripped Lower (05-2994-B), Features","url":"https://www.primaryarms.com/geissele-automatics-super-duty-stripped-ar-15-lower-stripped-lower","retrieved":"2026-10-28","via":"harvest"},"note":"Primary Arms: '.250\" takedown holes', and 'The .250-inch takedown holes and Safe/Fire indicators match standard AR-15 conventions'. A nominal size, the pins'."}],"adopt":{"from":"tdp","reason":"The page's .250 is the nominal size of the standard's pins (\"match standard AR-15 conventions\"); the drawing's hole is .251. Drawn at the drawing's."}},"rear_behind_pin":{"label":"Rear face (the buffer tower's, where the end plate bears) behind the takedown pin","kind":"length","measurements":[{"id":"std","value":1.125,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"-{std.ar15.receiver_rear_x}","via":"harvest"},"note":"A mil-spec lower: the rear face is the drawing's (7.503 -.006 behind the pivot pin). The rectified right photo's silhouette there is the ring's near side (rear_face_x, 0.015 behind it)."}]},"rear_face_x":{"label":"Receiver rear silhouette below the tower ring, X","kind":"length","measurements":[{"id":"right","value":-1.14,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower efc0b44358f7 (right side: Primary Arms' photo ddfadb3e24e2 (05-2994-B_05) laid square onto the right face by the drawing's holes, the far wall's share taken off)","scaleRef":"frame from the reviewed holes takedown, pivot (200.0 px/in, rms 0.000 in over 2 points)","method":"x_min in y [-0.9, 0.0] of the traced outline (tools/trace.py)","via":"harvest"},"note":"Rear face of the receiver below the tower's ring: the drawing's is -1.125 (std.ar15.receiver_rear_x)."}],"note":"The silhouette's rear edge under the ring: the ring's near side, laid on the near face's plane. The face is the drawing's (rear_behind_pin)."},"tower_top_above_pin":{"label":"Top of the buffer-tower ring above the pin line","kind":"length","measurements":[{"id":"std","value":1.5735,"unit":"in","pm":0.0065,"source":{"type":"derived","expr":"{std.ar15.buffer_tower_top_y}","via":"harvest"},"note":"A mil-spec lower: the ring's top is the drawing's (1.325 above the deck)."},{"id":"right","value":1.575,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower efc0b44358f7 (right side: Primary Arms' photo ddfadb3e24e2, 05-2994-B_05, laid square onto the right face at 200 px/in by a homography fitted to the near rims of the Army drawing's six holes on it, each within 0.0034 in after the fit)","scaleRef":"the rectification's frame: takedown pin (319.5, 399.5), pivot (1594.5, 399.5) px, 200 px/in (.cache/batch15/geissele-super-duty-stripped-lower/rect.py in the main checkout, holes.py beside it)","method":"y_max of the traced outline (tools/trace.py): the ring's silhouette, from a lens 23 in away whose foot is 2 in under the ring's top","via":"harvest"}},{"id":"left","value":1.57,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower aa5652aaecd2 (left side: Primary Arms' photo 80554f08bf56 laid square onto the left face at 200 px/in by an affine fit to the near rims of the drawing's six holes on it, each within 0.031 in after the fit; shown facing right)","scaleRef":"the rectification's frame: takedown pin (319.5, 399.5), pivot (1594.5, 399.5) px, 200 px/in; in the same rows the bolt catch's slot, the drawing's 3.203 to 3.375, reads 3.24 to 3.40: x read on this picture near the slot is taken 0.03 back, said in each reading","method":"y_max of the left outline traced as a check (tools/trace.py)","via":"harvest"}}],"adopt":{"from":"std","reason":"The drawing's; both photos' ring tops are within its ± and their own."}},"tower_front_x":{"label":"Buffer-tower front edge (the side walls' sweep up to the ring), X","kind":"length","measurements":[{"id":"right","value":-0.418,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower efc0b44358f7 (right side: Primary Arms' photo ddfadb3e24e2 (05-2994-B_05) laid square onto the right face by the drawing's holes, the far wall's share taken off)","scaleRef":"frame from the reviewed holes takedown, pivot (200.0 px/in, rms 0.000 in over 2 points)","method":"x_max in x [-1.5, 3.0] in y [0.5, 1.4] of the traced outline (tools/trace.py)","via":"harvest"},"note":"Front edge of the walls' sweep up to the ring, above the deck."}],"note":"The outline's front edge above the deck between Y 0.5 and 1.4. The ring's front face is the drawing's (std.ar15.buffer_tower_front_x) and the walls rise to it along the drawing's arc (std.ar15.rear_wall_arc_r): this figure is only how far forward the model's tower block is taken from the outline before that arc is cut."},"deck_above_pin":{"label":"Receiver top deck above the pin line","kind":"length","measurements":[{"id":"right","value":0.255,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower efc0b44358f7 (right side: Primary Arms' photo ddfadb3e24e2 (05-2994-B_05) laid square onto the right face by the drawing's holes, the far wall's share taken off)","scaleRef":"frame from the reviewed holes takedown, pivot (200.0 px/in, rms 0.000 in over 2 points)","method":"top (tooth tops: the edge's max over 0.05 in windows) along x [0.6, 5.8] of the traced outline (tools/trace.py)","via":"harvest"},"note":"The near wall's top edge between the tower and the pivot lug: the drawing's deck is 0.2485 (std.ar15.deck_y)."}],"note":"std.ar15.deck_y is 0.2485 (.250 -.003): the outline's top between the tower and the pivot lug is a reading of that plane, and the model's deck is the plane itself (lib.deck_outline). The left picture's outline reads 0.230 there (its affine fit: the check fails by 0.004 past its ±)."},"front_ahead_of_pin":{"label":"Front of the pivot-pin lug ahead of the takedown pin","kind":"length","measurements":[{"id":"right","value":6.555,"unit":"in","pm":0.011,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower efc0b44358f7 (right side: Primary Arms' photo ddfadb3e24e2 (05-2994-B_05) laid square onto the right face by the drawing's holes, the far wall's share taken off)","scaleRef":"frame from the reviewed holes takedown, pivot (200.0 px/in, rms 0.000 in over 2 points)","method":"x_max of the traced outline (tools/trace.py)","via":"harvest"},"note":"Front of the pivot-pin lug."}]},"bottom_below_pin":{"label":"Lowest point below the pin line (the trigger guard's ears)","kind":"length","measurements":[{"id":"right","value":2.35,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower efc0b44358f7 (right side: Primary Arms' photo ddfadb3e24e2 (05-2994-B_05) laid square onto the right face by the drawing's holes, the far wall's share taken off)","scaleRef":"frame from the reviewed holes takedown, pivot (200.0 px/in, rms 0.000 in over 2 points)","method":"−y_min of the traced outline (tools/trace.py)","via":"harvest"},"note":"Lowest point: the trigger guard's front ear, at the well's rear."}]},"magwell_front_x":{"label":"Magwell front face, X","kind":"length","measurements":[{"id":"right","value":6.09,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower efc0b44358f7 (right side: Primary Arms' photo ddfadb3e24e2 (05-2994-B_05) laid square onto the right face by the drawing's holes, the far wall's share taken off)","scaleRef":"frame from the reviewed holes takedown, pivot (200.0 px/in, rms 0.000 in over 2 points)","method":"x_max in x [3.0, 7.0] in y [-1.5, -0.6] of the traced outline (tools/trace.py)","via":"harvest"},"note":"Front face of the magazine well."}]},"magwell_wall_rear_x":{"label":"Magazine well's outside walls, rear edge, X (right side)","kind":"length","measurements":[{"id":"right","value":3.5,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower efc0b44358f7 (right side: Primary Arms' photo ddfadb3e24e2, 05-2994-B_05, laid square onto the right face at 200 px/in by a homography fitted to the near rims of the Army drawing's six holes on it, each within 0.0034 in after the fit)","scaleRef":"the rectification's frame: takedown pin (319.5, 399.5), pivot (1594.5, 399.5) px, 200 px/in (.cache/batch15/geissele-super-duty-stripped-lower/rect.py in the main checkout, holes.py beside it)","method":"the edge's dark line between two lit ones in grey profiles along rows Y -1.6 and -2.0 (prof.py): 3.50 in both, from below the fence down to the trigger guard's front ear","via":"harvest"}}],"note":"On the right, the wall's rear edge runs up into the fence's front edge (3.545). The Workhorse's is 3.619, Bear Creek's 3.58."},"magwell_wall_rear_x_left":{"label":"Magazine well's outside walls, rear edge, X (left side)","kind":"length","measurements":[{"id":"left","value":3.485,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower aa5652aaecd2 (left side: Primary Arms' photo 80554f08bf56 laid square onto the left face at 200 px/in by an affine fit to the near rims of the drawing's six holes on it, each within 0.031 in after the fit; shown facing right)","scaleRef":"the rectification's frame: takedown pin (319.5, 399.5), pivot (1594.5, 399.5) px, 200 px/in; in the same rows the bolt catch's slot, the drawing's 3.203 to 3.375, reads 3.24 to 3.40: x read on this picture near the slot is taken 0.03 back, said in each reading","method":"the step's dark line between two lit ones along row Y -1.5 (prof.py), at 3.515 on the picture, less 0.03","via":"harvest"}}],"note":"On the left the wall's rear edge is the step ahead of the trigger guard's front ear; above it curves back toward the bolt catch's bosses (magwell_wall_upper_rear_x_left). The Workhorse's is 3.455, Bear Creek's 3.48."},"magwell_wall_upper_rear_x_left":{"label":"Magazine well's outside walls, rear edge above the step's curve, X (left side)","kind":"length","measurements":[{"id":"left","value":2.945,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower aa5652aaecd2 (left side: Primary Arms' photo 80554f08bf56 laid square onto the left face at 200 px/in by an affine fit to the near rims of the drawing's six holes on it, each within 0.031 in after the fit; shown facing right)","scaleRef":"the rectification's frame: takedown pin (319.5, 399.5), pivot (1594.5, 399.5) px, 200 px/in; in the same rows the bolt catch's slot, the drawing's 3.203 to 3.375, reads 3.24 to 3.40: x read on this picture near the slot is taken 0.03 back, said in each reading","method":"the edge's dark line along rows Y 0.1 and -0.4 (prof.py), at 2.97 to 2.975 on the picture, less 0.03; straight from the deck down to the curve","via":"harvest"}}],"note":"The Workhorse's is 2.948, Bear Creek's 2.96."},"magwell_wall_curve_top_y_left":{"label":"Magazine well's outside walls, left side, where the rear edge starts to curve forward, Y","kind":"length","measurements":[{"id":"left","value":-0.75,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower aa5652aaecd2 (left side: Primary Arms' photo 80554f08bf56 laid square onto the left face at 200 px/in by an affine fit to the near rims of the drawing's six holes on it, each within 0.031 in after the fit; shown facing right)","scaleRef":"the rectification's frame: takedown pin (319.5, 399.5), pivot (1594.5, 399.5) px, 200 px/in; in the same rows the bolt catch's slot, the drawing's 3.203 to 3.375, reads 3.24 to 3.40: x read on this picture near the slot is taken 0.03 back, said in each reading","method":"the edge's lit line on a 3.5x crop with a 0.05 in grid (g-left-curve.png): upright from the deck to about -0.75, then forward through (3.2, -0.95) and (3.4, -1.05)","via":"harvest"}}]},"magwell_wall_curve_bottom_y_left":{"label":"Magazine well's outside walls, left side, where the rear edge's curve meets the step, Y","kind":"length","measurements":[{"id":"left","value":-1.15,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower aa5652aaecd2 (left side: Primary Arms' photo 80554f08bf56 laid square onto the left face at 200 px/in by an affine fit to the near rims of the drawing's six holes on it, each within 0.031 in after the fit; shown facing right)","scaleRef":"the rectification's frame: takedown pin (319.5, 399.5), pivot (1594.5, 399.5) px, 200 px/in; in the same rows the bolt catch's slot, the drawing's 3.203 to 3.375, reads 3.24 to 3.40: x read on this picture near the slot is taken 0.03 back, said in each reading","method":"the same crop: the curve reaches the step's upright line at about -1.15, upright from there down","via":"harvest"}}],"note":"Between the two ends the edge is drawn as a smooth S (3t^2 - 2t^3), as the catalog's other forged lowers' is."},"bolt_catch_boss_rear_x":{"label":"Bolt catch bosses: the rear boss's rear edge, X (left side)","kind":"length","measurements":[{"id":"left","value":3.008,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower aa5652aaecd2 (left side: Primary Arms' photo 80554f08bf56 laid square onto the left face at 200 px/in by an affine fit to the near rims of the drawing's six holes on it, each within 0.031 in after the fit; shown facing right)","scaleRef":"the rectification's frame: takedown pin (319.5, 399.5), pivot (1594.5, 399.5) px, 200 px/in; in the same rows the bolt catch's slot, the drawing's 3.203 to 3.375, reads 3.24 to 3.40: x read on this picture near the slot is taken 0.03 back, said in each reading","method":"along row Y 0.1 (prof.py) the rear boss's rear edge stands 0.195 behind the slot's rear edge (3.045 and 3.24 on the picture): from the drawing's slot edge, 3.203 - 0.195","via":"harvest"}}],"note":"The Workhorse's is 3.013, Bear Creek's 3.05."},"bolt_catch_gap_rear_x":{"label":"Bolt catch bosses: the gap between them (where the catch sits), rear edge, X","kind":"length","measurements":[{"id":"tdp","value":3.203,"unit":"in","pm":0.007,"source":{"type":"derived","expr":"{std.ar15.bolt_catch_slot_front_x} - {std.ar15.bolt_catch_slot_width}","via":"harvest"},"note":"The gap is the drawing's slot for the catch, at the left face."},{"id":"left","value":3.24,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower aa5652aaecd2 (left side: Primary Arms' photo 80554f08bf56 laid square onto the left face at 200 px/in by an affine fit to the near rims of the drawing's six holes on it, each within 0.031 in after the fit; shown facing right)","scaleRef":"the rectification's frame: takedown pin (319.5, 399.5), pivot (1594.5, 399.5) px, 200 px/in; in the same rows the bolt catch's slot, the drawing's 3.203 to 3.375, reads 3.24 to 3.40: x read on this picture near the slot is taken 0.03 back, said in each reading","method":"the gap's dark edge along row Y 0.1 (prof.py), as read on the picture (not moved)","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's slot; the picture has it 0.037 ahead, inside its ±: the offset every x read near it on this picture is taken back by."}},"bolt_catch_gap_front_x":{"label":"Bolt catch bosses: the gap's front edge, X","kind":"length","measurements":[{"id":"tdp","value":3.375,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.ar15.bolt_catch_slot_front_x}","via":"harvest"},"note":"The gap is the drawing's slot for the catch, at the left face."},{"id":"left","value":3.4,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower aa5652aaecd2 (left side: Primary Arms' photo 80554f08bf56 laid square onto the left face at 200 px/in by an affine fit to the near rims of the drawing's six holes on it, each within 0.031 in after the fit; shown facing right)","scaleRef":"the rectification's frame: takedown pin (319.5, 399.5), pivot (1594.5, 399.5) px, 200 px/in; in the same rows the bolt catch's slot, the drawing's 3.203 to 3.375, reads 3.24 to 3.40: x read on this picture near the slot is taken 0.03 back, said in each reading","method":"the gap's dark edge along row Y 0.1 (prof.py), as read on the picture (not moved)","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's slot; the picture has it 0.025 ahead, inside its ±."}},"bolt_catch_boss_front_x":{"label":"Bolt catch bosses: the front boss's front edge, X","kind":"length","measurements":[{"id":"left","value":3.555,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower aa5652aaecd2 (left side: Primary Arms' photo 80554f08bf56 laid square onto the left face at 200 px/in by an affine fit to the near rims of the drawing's six holes on it, each within 0.031 in after the fit; shown facing right)","scaleRef":"the rectification's frame: takedown pin (319.5, 399.5), pivot (1594.5, 399.5) px, 200 px/in; in the same rows the bolt catch's slot, the drawing's 3.203 to 3.375, reads 3.24 to 3.40: x read on this picture near the slot is taken 0.03 back, said in each reading","method":"along row Y 0.1 (prof.py) the front boss's front edge stands 0.18 ahead of the slot's front edge (3.58 and 3.40 on the picture): from the drawing's slot edge, 3.375 + 0.18","via":"harvest"}}],"note":"The Workhorse's is 3.576, Bear Creek's 3.58."},"bolt_catch_boss_bottom_y":{"label":"Bolt catch bosses: their bottom edges, Y (they rise to the deck)","kind":"length","measurements":[{"id":"left","value":-0.12,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower aa5652aaecd2 (left side: Primary Arms' photo 80554f08bf56 laid square onto the left face at 200 px/in by an affine fit to the near rims of the drawing's six holes on it, each within 0.031 in after the fit; shown facing right)","scaleRef":"the rectification's frame: takedown pin (319.5, 399.5), pivot (1594.5, 399.5) px, 200 px/in; in the same rows the bolt catch's slot, the drawing's 3.203 to 3.375, reads 3.24 to 3.40: x read on this picture near the slot is taken 0.03 back, said in each reading","method":"down column X 3.1 (prof.py): the boss's face to -0.06, its lower edge's shadow at -0.09, a lit fillet to -0.15, the wall from -0.2; the edge taken between","via":"harvest"}}],"note":"The Workhorse's is -0.05, Bear Creek's -0.14."},"band_rear_x":{"label":"The raised band down the well's left wall, its rear edge, X","kind":"length","measurements":[{"id":"model","value":3.975,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{std.ar15.magwell_band_rear_x}","via":"harvest"},"note":"The reference CAD model's band on a mil-spec forging (std.ar15.magwell_band_*), which the model draws; the rectified left photo has a line at about 3.98 from the deck to the lip (g-left-catch.png), not read finer."}],"note":"A check that this forging has the standard's band where the standard has it."},"band_front_x":{"label":"The raised band down the well's left wall, its front edge, X","kind":"length","measurements":[{"id":"model","value":4.549,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{std.ar15.magwell_band_front_x}","via":"harvest"},"note":"The reference CAD model's band on a mil-spec forging, which the model draws; the rectified left photo has a line at about 4.6, the foot of the band's slope (4.549 + std.ar15.magwell_band_side), not read finer."}]},"fence_rear_x":{"label":"The magazine catch's fence, its flat face's rear edge, X","kind":"length","measurements":[{"id":"right","value":2.955,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower efc0b44358f7 (right side: Primary Arms' photo ddfadb3e24e2, 05-2994-B_05, laid square onto the right face at 200 px/in by a homography fitted to the near rims of the Army drawing's six holes on it, each within 0.0034 in after the fit)","scaleRef":"the rectification's frame: takedown pin (319.5, 399.5), pivot (1594.5, 399.5) px, 200 px/in (.cache/batch15/geissele-super-duty-stripped-lower/rect.py in the main checkout, holes.py beside it)","method":"the edge's dark line between two lit ones along row Y -0.6 (prof.py): 2.94 to 2.97","via":"harvest"}}],"note":"The Workhorse's is 3.02, Bear Creek's 2.97. The same line runs up to the deck as the roll's rear end (well_roll_rear_x)."},"fence_front_x":{"label":"The magazine catch's fence, its flat face's front edge, X","kind":"length","measurements":[{"id":"right","value":3.545,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower efc0b44358f7 (right side: Primary Arms' photo ddfadb3e24e2, 05-2994-B_05, laid square onto the right face at 200 px/in by a homography fitted to the near rims of the Army drawing's six holes on it, each within 0.0034 in after the fit)","scaleRef":"the rectification's frame: takedown pin (319.5, 399.5), pivot (1594.5, 399.5) px, 200 px/in (.cache/batch15/geissele-super-duty-stripped-lower/rect.py in the main checkout, holes.py beside it)","method":"along row Y -0.6 (prof.py): the face's lit edge at 3.52 to 3.54 and its foot's shadow at 3.55 to 3.60","via":"harvest"}}],"note":"The rib beside it runs forward from here to 3.92, from the roll down to a point (not drawn: how far it stands off the wall's face isn't read)."},"fence_top_y":{"label":"The magazine catch's fence, its flat face's top edge, Y","kind":"length","measurements":[{"id":"right","value":-0.215,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower efc0b44358f7 (right side: Primary Arms' photo ddfadb3e24e2, 05-2994-B_05, laid square onto the right face at 200 px/in by a homography fitted to the near rims of the Army drawing's six holes on it, each within 0.0034 in after the fit)","scaleRef":"the rectification's frame: takedown pin (319.5, 399.5), pivot (1594.5, 399.5) px, 200 px/in (.cache/batch15/geissele-super-duty-stripped-lower/rect.py in the main checkout, holes.py beside it)","method":"down column X 3.25 (prof.py): the shadow at -0.17 and the lit edge at -0.19 to -0.21, the fence's face from -0.22: where it meets the roll's lower edge","via":"harvest"}}]},"fence_bottom_y":{"label":"The magazine catch's fence, its flat face's bottom edge, Y","kind":"length","measurements":[{"id":"right","value":-0.975,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower efc0b44358f7 (right side: Primary Arms' photo ddfadb3e24e2, 05-2994-B_05, laid square onto the right face at 200 px/in by a homography fitted to the near rims of the Army drawing's six holes on it, each within 0.0034 in after the fit)","scaleRef":"the rectification's frame: takedown pin (319.5, 399.5), pivot (1594.5, 399.5) px, 200 px/in (.cache/batch15/geissele-super-duty-stripped-lower/rect.py in the main checkout, holes.py beside it)","method":"down column X 3.25 (prof.py): the fence's face to -0.93, lit -0.94 to -0.955, the edge's dark line at -0.97 to -0.99, lit again at -1.01","via":"harvest"}}],"note":"The Workhorse's is -0.91, Bear Creek's -0.93."},"fence_corner_r":{"label":"The magazine catch's fence, its flat face's corners, radius","kind":"length","measurements":[{"id":"right","value":0.08,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower efc0b44358f7 (right side: Primary Arms' photo ddfadb3e24e2, 05-2994-B_05, laid square onto the right face at 200 px/in by a homography fitted to the near rims of the Army drawing's six holes on it, each within 0.0034 in after the fit)","scaleRef":"the rectification's frame: takedown pin (319.5, 399.5), pivot (1594.5, 399.5) px, 200 px/in (.cache/batch15/geissele-super-duty-stripped-lower/rect.py in the main checkout, holes.py beside it)","method":"the corners' rounds on a 3x crop with a 0.05 in grid (g-right-fence.png), by eye against the grid","via":"harvest"}}]},"well_roll_crest_out":{"label":"The roll along the top of the magazine well's right wall, its crest from the centre plane (Z)","kind":"length","measurements":[{"id":"workhorse","value":0.8,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{bad-workhorse-lower.well_roll_crest_out}","via":"harvest"},"note":"NOT READ ON THIS LOWER: a side view doesn't show how far a roll stands out, and no view on file looks along the receiver. The catalog's forged mil-spec lower's reading (the Workhorse's, through a camera fitted to its oblique photo and checked by its seller's 1.5 in width), which Bear Creek's has too; this lower's right side has the roll where those two have it (its lower edge -0.21 for their -0.204, its ends 2.955 and 6.25 for their 2.905 to 2.91 and 6.231 to 6.237)."}]},"well_roll_bottom_y":{"label":"The roll along the top of the well's right wall, its lower edge, Y","kind":"length","measurements":[{"id":"right","value":-0.21,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower efc0b44358f7 (right side: Primary Arms' photo ddfadb3e24e2, 05-2994-B_05, laid square onto the right face at 200 px/in by a homography fitted to the near rims of the Army drawing's six holes on it, each within 0.0034 in after the fit)","scaleRef":"the rectification's frame: takedown pin (319.5, 399.5), pivot (1594.5, 399.5) px, 200 px/in (.cache/batch15/geissele-super-duty-stripped-lower/rect.py in the main checkout, holes.py beside it)","method":"down column X 5.0 (prof.py): the roll's lit crest about +0.15, its lower edge's shadow at -0.17, a lit line at -0.19 to -0.20, the wall's face from -0.22","via":"harvest"}}],"note":"The Workhorse's and Bear Creek's are -0.204."},"well_roll_rear_x":{"label":"The roll along the top of the well's right wall, its rear end, X","kind":"length","measurements":[{"id":"right","value":2.955,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower efc0b44358f7 (right side: Primary Arms' photo ddfadb3e24e2, 05-2994-B_05, laid square onto the right face at 200 px/in by a homography fitted to the near rims of the Army drawing's six holes on it, each within 0.0034 in after the fit)","scaleRef":"the rectification's frame: takedown pin (319.5, 399.5), pivot (1594.5, 399.5) px, 200 px/in (.cache/batch15/geissele-super-duty-stripped-lower/rect.py in the main checkout, holes.py beside it)","method":"along row Y 0.05 (prof.py): a lit line at 2.92, the end's dark line at 2.95, the roll's rounded end lit from 2.98 to about 3.15","via":"harvest"}}],"note":"The Workhorse's is 2.905, Bear Creek's 2.91."},"well_roll_rear_round":{"label":"The roll along the top of the well's right wall, how far its rounded rear end runs before the roll is full","kind":"length","measurements":[{"id":"right","value":0.17,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower efc0b44358f7 (right side: Primary Arms' photo ddfadb3e24e2, 05-2994-B_05, laid square onto the right face at 200 px/in by a homography fitted to the near rims of the Army drawing's six holes on it, each within 0.0034 in after the fit)","scaleRef":"the rectification's frame: takedown pin (319.5, 399.5), pivot (1594.5, 399.5) px, 200 px/in (.cache/batch15/geissele-super-duty-stripped-lower/rect.py in the main checkout, holes.py beside it)","method":"along row Y 0.05 (prof.py): the lit rounding from the end's line at 2.955 to about 3.12, where the roll's face is level again; a reading of where the light changes, not of a profile","via":"harvest"}},{"id":"workhorse","value":0.19,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{bad-workhorse-lower.well_roll_rear_round}","via":"harvest"},"note":"The Workhorse's, on its own right photo."}],"adopt":{"from":"right","reason":"This lower's own photo; the Workhorse's agrees within both ±."}},"well_roll_front_x":{"label":"The roll along the top of the well's right wall, its front end (a flat face beside the pivot lug), X","kind":"length","measurements":[{"id":"right","value":6.25,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower efc0b44358f7 (right side: Primary Arms' photo ddfadb3e24e2, 05-2994-B_05, laid square onto the right face at 200 px/in by a homography fitted to the near rims of the Army drawing's six holes on it, each within 0.0034 in after the fit)","scaleRef":"the rectification's frame: takedown pin (319.5, 399.5), pivot (1594.5, 399.5) px, 200 px/in (.cache/batch15/geissele-super-duty-stripped-lower/rect.py in the main checkout, holes.py beside it)","method":"along row Y -0.1 (prof.py): the roll's face level to 6.24, its end's dark line at 6.25 to 6.26, the pivot lug beyond","via":"harvest"}},{"id":"pinflat","value":6.2395,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{std.ar15.pin_spacing} - {rise-lpk.pivot_pin_head_flat}","via":"harvest"},"note":"Where the Army's pivot pin has the flat on its head (.1355 from its axis, drawing 8448621), turned to the rear: the flat lies against the roll's end, which can be no further forward."}],"adopt":{"from":"pinflat","reason":"A seat: the pivot pin's flat bears on the roll's end. This lower's photo has the end 0.0105 further forward, inside its ±; drawn there, the pin's head would stand in the roll."},"note":"The Workhorse's is 6.231, Bear Creek's 6.237."},"roll_hole_x":{"label":"The small blind hole in the roll's face behind the pivot lug, X","kind":"length","measurements":[{"id":"right","value":5.322,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower efc0b44358f7 (right side: Primary Arms' photo ddfadb3e24e2, 05-2994-B_05, laid square onto the right face at 200 px/in by a homography fitted to the near rims of the Army drawing's six holes on it, each within 0.0034 in after the fit)","scaleRef":"the rectification's frame: takedown pin (319.5, 399.5), pivot (1594.5, 399.5) px, 200 px/in (.cache/batch15/geissele-super-duty-stripped-lower/rect.py in the main checkout, holes.py beside it)","method":"the dark disc's two edges on a 2x crop with a 0.05 in grid (g-right-roll.png), 5.30 and 5.345","via":"harvest"}}],"note":"Bear Creek's has one 1.0 in behind its pivot pin; this one is 1.05."},"roll_hole_y":{"label":"The small blind hole in the roll's face, Y","kind":"length","measurements":[{"id":"right","value":0,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower efc0b44358f7 (right side: Primary Arms' photo ddfadb3e24e2, 05-2994-B_05, laid square onto the right face at 200 px/in by a homography fitted to the near rims of the Army drawing's six holes on it, each within 0.0034 in after the fit)","scaleRef":"the rectification's frame: takedown pin (319.5, 399.5), pivot (1594.5, 399.5) px, 200 px/in (.cache/batch15/geissele-super-duty-stripped-lower/rect.py in the main checkout, holes.py beside it)","method":"the dark disc's centre on the same crop: on the pin line","via":"harvest"}}]},"roll_hole_d":{"label":"The small blind hole in the roll's face, diameter","kind":"length","measurements":[{"id":"right","value":0.045,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower efc0b44358f7 (right side: Primary Arms' photo ddfadb3e24e2, 05-2994-B_05, laid square onto the right face at 200 px/in by a homography fitted to the near rims of the Army drawing's six holes on it, each within 0.0034 in after the fit)","scaleRef":"the rectification's frame: takedown pin (319.5, 399.5), pivot (1594.5, 399.5) px, 200 px/in (.cache/batch15/geissele-super-duty-stripped-lower/rect.py in the main checkout, holes.py beside it)","method":"the dark disc's width on the same crop, about 9 px","via":"harvest"}}]},"roll_hole_depth":{"label":"The small blind hole in the roll's face, depth","kind":"length","measurements":[{"id":"assumed","value":0.06,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file looks into the hole. Deep enough to read as a hole, short of the roll's back.","via":"harvest"}}]},"selector_pad_length":{"label":"The two oblong pads either side of the selector (left side), each one's length along the receiver","kind":"length","measurements":[{"id":"left","value":0.35,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower aa5652aaecd2 (left side: Primary Arms' photo 80554f08bf56 laid square onto the left face at 200 px/in by an affine fit to the near rims of the drawing's six holes on it, each within 0.031 in after the fit; shown facing right)","scaleRef":"the rectification's frame: takedown pin (319.5, 399.5), pivot (1594.5, 399.5) px, 200 px/in; in the same rows the bolt catch's slot, the drawing's 3.203 to 3.375, reads 3.24 to 3.40: x read on this picture near the slot is taken 0.03 back, said in each reading","method":"the pad's rim, where the face ends round it, on a 3x crop with a 0.05 in grid (g-left-pads.png): the rear pad from 0.05 to 0.40, the front from 1.17 to 1.52, both from -0.205 to -0.43","via":"harvest"}}],"note":"Stadiums, their ends round: lit along their upper halves and dark along their lower halves in the square view, and lit along their upper edges in Primary Arms' three-quarter view from behind (86e395231fc0): raised, not pockets."},"selector_pad_height":{"label":"The oblong pads by the selector, each one's height","kind":"length","measurements":[{"id":"left","value":0.225,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower aa5652aaecd2 (left side: Primary Arms' photo 80554f08bf56 laid square onto the left face at 200 px/in by an affine fit to the near rims of the drawing's six holes on it, each within 0.031 in after the fit; shown facing right)","scaleRef":"the rectification's frame: takedown pin (319.5, 399.5), pivot (1594.5, 399.5) px, 200 px/in; in the same rows the bolt catch's slot, the drawing's 3.203 to 3.375, reads 3.24 to 3.40: x read on this picture near the slot is taken 0.03 back, said in each reading","method":"the pad's rim, where the face ends round it, on a 3x crop with a 0.05 in grid (g-left-pads.png): the rear pad from 0.05 to 0.40, the front from 1.17 to 1.52, both from -0.205 to -0.43","via":"harvest"}}]},"selector_pad_rear_x":{"label":"The rear oblong pad's centre, X","kind":"length","measurements":[{"id":"left","value":0.225,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower aa5652aaecd2 (left side: Primary Arms' photo 80554f08bf56 laid square onto the left face at 200 px/in by an affine fit to the near rims of the drawing's six holes on it, each within 0.031 in after the fit; shown facing right)","scaleRef":"the rectification's frame: takedown pin (319.5, 399.5), pivot (1594.5, 399.5) px, 200 px/in; in the same rows the bolt catch's slot, the drawing's 3.203 to 3.375, reads 3.24 to 3.40: x read on this picture near the slot is taken 0.03 back, said in each reading","method":"the pad's rim, where the face ends round it, on a 3x crop with a 0.05 in grid (g-left-pads.png): the rear pad from 0.05 to 0.40, the front from 1.17 to 1.52, both from -0.205 to -0.43","via":"harvest"}}]},"selector_pad_front_x":{"label":"The front oblong pad's centre, X","kind":"length","measurements":[{"id":"left","value":1.345,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower aa5652aaecd2 (left side: Primary Arms' photo 80554f08bf56 laid square onto the left face at 200 px/in by an affine fit to the near rims of the drawing's six holes on it, each within 0.031 in after the fit; shown facing right)","scaleRef":"the rectification's frame: takedown pin (319.5, 399.5), pivot (1594.5, 399.5) px, 200 px/in; in the same rows the bolt catch's slot, the drawing's 3.203 to 3.375, reads 3.24 to 3.40: x read on this picture near the slot is taken 0.03 back, said in each reading","method":"the pad's rim, where the face ends round it, on a 3x crop with a 0.05 in grid (g-left-pads.png): the rear pad from 0.05 to 0.40, the front from 1.17 to 1.52, both from -0.205 to -0.43","via":"harvest"}}]},"selector_pad_y":{"label":"The oblong pads' centres, Y","kind":"length","measurements":[{"id":"left","value":-0.317,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower aa5652aaecd2 (left side: Primary Arms' photo 80554f08bf56 laid square onto the left face at 200 px/in by an affine fit to the near rims of the drawing's six holes on it, each within 0.031 in after the fit; shown facing right)","scaleRef":"the rectification's frame: takedown pin (319.5, 399.5), pivot (1594.5, 399.5) px, 200 px/in; in the same rows the bolt catch's slot, the drawing's 3.203 to 3.375, reads 3.24 to 3.40: x read on this picture near the slot is taken 0.03 back, said in each reading","method":"the pad's rim, where the face ends round it, on a 3x crop with a 0.05 in grid (g-left-pads.png): the rear pad from 0.05 to 0.40, the front from 1.17 to 1.52, both from -0.205 to -0.43","via":"harvest"}}]},"selector_pad_proud":{"label":"The oblong pads by the selector, how far they stand off the face","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows a pad in profile. Raised by their light in two views (lit above, dark below in the square one; lit upper edges from above and behind); a few hundredths, as a forging's marks stand.","via":"harvest"}}]},"rib_rear_x":{"label":"The rib down the well's right wall beside the fence: its rear edge, X","kind":"length","measurements":[{"id":"right","value":3.6,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower efc0b44358f7 (right side: Primary Arms' photo ddfadb3e24e2, 05-2994-B_05, laid square onto the right face at 200 px/in by a homography fitted to the near rims of the Army drawing's six holes on it, each within 0.0034 in after the fit)","scaleRef":"the rectification's frame: takedown pin (319.5, 399.5), pivot (1594.5, 399.5) px, 200 px/in (.cache/batch15/geissele-super-duty-stripped-lower/rect.py in the main checkout, holes.py beside it)","method":"the rib's lit band between its two edges' lines, in grey profiles along rows Y -0.4 to -1.6 (prof.py) and a 3x crop with a 0.05 in grid (g-right-rib.png): its rear edge's line at 3.59 to 3.61 from the roll down to -1.0","via":"harvest"}}],"note":"A forging's rib that runs down from the roll, between the fence and the wall's face, to a point."},"rib_front_x":{"label":"The rib's front edge, X","kind":"length","measurements":[{"id":"right","value":3.9,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower efc0b44358f7 (right side: Primary Arms' photo ddfadb3e24e2, 05-2994-B_05, laid square onto the right face at 200 px/in by a homography fitted to the near rims of the Army drawing's six holes on it, each within 0.0034 in after the fit)","scaleRef":"the rectification's frame: takedown pin (319.5, 399.5), pivot (1594.5, 399.5) px, 200 px/in (.cache/batch15/geissele-super-duty-stripped-lower/rect.py in the main checkout, holes.py beside it)","method":"the rib's lit band between its two edges' lines, in grey profiles along rows Y -0.4 to -1.6 (prof.py) and a 3x crop with a 0.05 in grid (g-right-rib.png): its front edge's dark line at 3.89 to 3.91 from the roll down to -1.2","via":"harvest"}}]},"rib_rear_turn_y":{"label":"The rib's rear edge: where it turns toward the point, Y","kind":"length","measurements":[{"id":"right","value":-1,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower efc0b44358f7 (right side: Primary Arms' photo ddfadb3e24e2, 05-2994-B_05, laid square onto the right face at 200 px/in by a homography fitted to the near rims of the Army drawing's six holes on it, each within 0.0034 in after the fit)","scaleRef":"the rectification's frame: takedown pin (319.5, 399.5), pivot (1594.5, 399.5) px, 200 px/in (.cache/batch15/geissele-super-duty-stripped-lower/rect.py in the main checkout, holes.py beside it)","method":"the rib's lit band between its two edges' lines, in grey profiles along rows Y -0.4 to -1.6 (prof.py) and a 3x crop with a 0.05 in grid (g-right-rib.png): upright to about -1.0, then forward and down","via":"harvest"}}]},"rib_front_turn_y":{"label":"The rib's front edge: where it turns toward the point, Y","kind":"length","measurements":[{"id":"right","value":-1.2,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower efc0b44358f7 (right side: Primary Arms' photo ddfadb3e24e2, 05-2994-B_05, laid square onto the right face at 200 px/in by a homography fitted to the near rims of the Army drawing's six holes on it, each within 0.0034 in after the fit)","scaleRef":"the rectification's frame: takedown pin (319.5, 399.5), pivot (1594.5, 399.5) px, 200 px/in (.cache/batch15/geissele-super-duty-stripped-lower/rect.py in the main checkout, holes.py beside it)","method":"the rib's lit band between its two edges' lines, in grey profiles along rows Y -0.4 to -1.6 (prof.py) and a 3x crop with a 0.05 in grid (g-right-rib.png): upright to about -1.2, then back and down","via":"harvest"}}]},"rib_point_x":{"label":"The rib's lower point, X","kind":"length","measurements":[{"id":"right","value":3.73,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower efc0b44358f7 (right side: Primary Arms' photo ddfadb3e24e2, 05-2994-B_05, laid square onto the right face at 200 px/in by a homography fitted to the near rims of the Army drawing's six holes on it, each within 0.0034 in after the fit)","scaleRef":"the rectification's frame: takedown pin (319.5, 399.5), pivot (1594.5, 399.5) px, 200 px/in (.cache/batch15/geissele-super-duty-stripped-lower/rect.py in the main checkout, holes.py beside it)","method":"the rib's lit band between its two edges' lines, in grey profiles along rows Y -0.4 to -1.6 (prof.py) and a 3x crop with a 0.05 in grid (g-right-rib.png): the two edges meet at about (3.73, -1.50); along row -1.45 the band is 3.67 to 3.80, along -1.6 gone","via":"harvest"}}]},"rib_point_y":{"label":"The rib's lower point, Y","kind":"length","measurements":[{"id":"right","value":-1.5,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-lower efc0b44358f7 (right side: Primary Arms' photo ddfadb3e24e2, 05-2994-B_05, laid square onto the right face at 200 px/in by a homography fitted to the near rims of the Army drawing's six holes on it, each within 0.0034 in after the fit)","scaleRef":"the rectification's frame: takedown pin (319.5, 399.5), pivot (1594.5, 399.5) px, 200 px/in (.cache/batch15/geissele-super-duty-stripped-lower/rect.py in the main checkout, holes.py beside it)","method":"the rib's lit band between its two edges' lines, in grey profiles along rows Y -0.4 to -1.6 (prof.py) and a 3x crop with a 0.05 in grid (g-right-rib.png)","via":"harvest"}}]},"rib_proud":{"label":"The rib's crest, how far it stands off the well wall's face","kind":"length","measurements":[{"id":"assumed","value":0.04,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file looks along the wall. A round rib, lit across its width in the square view and standing well under the roll beside it in the three-quarter views (14b65221cdc5, c758c0df7335).","via":"harvest"}}]}}},{"subject":"geissele-super-duty-stripped-upper","title":"Geissele Automatics Super Duty Stripped Upper Receiver (in the Super Duty Receiver Set, 05-1171B / 05-1171S)","dimensions":{"weight":{"label":"Weight (the stripped receiver: no port door, forward assist or barrel)","kind":"mass","measurements":[{"id":"metal","value":7.66,"unit":"oz","pm":0.8,"source":{"type":"derived","basis":"This part's own model's metal: the closed volume of app/public/models/geissele-super-duty-stripped-upper.receiver.glb as its script built it (4.695 cubic inches: the traced outline above the deck across the mil-spec forging's section, its forward assist housing, deflector, hinge lugs, cam pin pad, lugs and threaded nose, its bore, channel, port and holes cut; the manifest's volume_in3) times what a cubic inch of 7075 weighs (std.density.aluminium_7075, 1.632 oz): 4.695 x 1.632 = 7.66 oz. Its pages: \"Forged 7075-T6 aluminum\" (Primary Arms), \"Upper Specs: Material: 7075-T6\" (Aegis Cerakote). ± a tenth, for the section and the left side, which are the mil-spec forging's and not read on this receiver.","via":"harvest"}}],"note":"No page states one: neither the set's sellers (Primary Arms, Aegis Cerakote, Charlie's Custom Clones, Blackstone) nor a review on file gives the upper's weight or the set's (Charlie's markup has \"weight\":null). Weighed by its metal: its model's closed volume times what a cubic inch of 7075 weighs (the pages: \"Forged 7075-T6 aluminum\")."},"bore_axis_above_pin":{"label":"Bore axis above the takedown pin centre","kind":"length","measurements":[{"id":"standard","value":0.8775,"unit":"in","pm":0.0015,"source":{"type":"derived","expr":"{std.ar15.bore_axis_y}","via":"harvest"},"note":"The standard's. Primary Arms' page for the black set it is sold in (05-1171B): \"Features: Forged 7075-T6 aluminum Hardcoat anodized black Mil-Spec dimensions\", \"It is compatible with Mil-Spec AR-15 parts and accessories\". Its being the Army drawing's receiver is what \"Mil-Spec dimensions\" is taken to say, and each face is tried on its photo."},{"id":"right","value":0.875,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-upper 95a4d20d054e (Aegis Cerakote's z05-1171b_super_duty_receiver_set_black_02: the black set 05-1171B from the right, this upper on its lower, 3292 x 1988)","scaleRef":"the lower's two pin holes, std.ar15.pin_spacing apart (the upper's own lug holes are inside them, on the same axes): each see-through opening fitted as its near rim's circle and its far rim's at once (references/geissele-super-duty-stripped-upper/work/holes.py: rms 0.23 px), their midpoints the frame's points: 341.0 px/in on the mid-plane, a pixel 0.003 in","method":"the threaded nose's top and bottom edges over x 6.7 to 7.0 read 1.498 and 0.251 (trace.py's y_max and y_min): their middle 0.8745; a turned nose's silhouette edges lie close to the mid-plane, so the lens moves them by less than a thousandth; ± is a pixel's few","via":"harvest"}}],"adopt":{"from":"standard","reason":"The drawings' figure; this receiver's own photo puts its nose's axis within its ± of it."}},"rail_top_above_pin":{"label":"The top rail's surface above the pin line","kind":"length","measurements":[{"id":"right","value":2.09,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-upper 95a4d20d054e (Aegis Cerakote's z05-1171b_super_duty_receiver_set_black_02: the black set 05-1171B from the right, this upper on its lower, 3292 x 1988)","scaleRef":"the lower's two pin holes, std.ar15.pin_spacing apart (the upper's own lug holes are inside them, on the same axes): each see-through opening fitted as its near rim's circle and its far rim's at once (references/geissele-super-duty-stripped-upper/work/holes.py: rms 0.23 px), their midpoints the frame's points: 341.0 px/in on the mid-plane, a pixel 0.003 in","method":"the tooth tops read 2.101 ± 0.009 over x 1.0 to 6.0 (trace.py's band_top); from a lens above the rail the silhouette's top is the top flat's far edge, 0.31 further than the mid-plane: the lens stands about 28 in away opposite x 4.6, y 3.0 (right_photo_lens_*), so what is z nearer than the mid-plane reads large about that point by 28 / (28 - z): 2.091; ± is the reading's and the lens's distance","via":"harvest"}}],"note":"Read on Aegis Cerakote's side photo of the set, in the frame of the lower's pin holes. The catalog's other forged flat tops read 2.09 the same way (expo-arms-stripped-upper.rail_top_above_pin, psa-stripped-upper.rail_top_above_pin) and the reference model of a mil-spec forging has 2.090."},"rail_slot0_x":{"label":"The rearmost rail slot's centre ahead of the takedown pin","kind":"length","measurements":[{"id":"right","value":1.3,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-upper 95a4d20d054e (Aegis Cerakote's z05-1171b_super_duty_receiver_set_black_02: the black set 05-1171B from the right, this upper on its lower, 3292 x 1988)","scaleRef":"the lower's two pin holes, std.ar15.pin_spacing apart (the upper's own lug holes are inside them, on the same axes): each see-through opening fitted as its near rim's circle and its far rim's at once (references/geissele-super-duty-stripped-upper/work/holes.py: rms 0.23 px), their midpoints the frame's points: 341.0 px/in on the mid-plane, a pixel 0.003 in","method":"the see-through gaps on rows 2.04 and 2.06 (work/rail.py): 13 of them; each read at its near edge (the front edge of a gap behind x 4.6, the rear edge of one ahead of it), the teeth's near faces about 0.4 nearer than the mid-plane: the lens stands about 28 in away opposite x 4.6, y 3.0 (right_photo_lens_*), so what is z nearer than the mid-plane reads large about that point by 28 / (28 - z); a slot's centre is that edge less half the standard's .206: the first slot at 1.28 by its own front edge, 1.30 to 1.31 by the ninth's to the thirteenth's at the standard pitch. The near edges run 0.4025 apart in the picture, 0.7% over the standard's .394 once brought back: what this frame and lens leave unexplained, 0.03 over the rail, inside the ±","via":"harvest"}}],"note":"Expo Arms' forged flat top reads 1.314 on a photo four times this one's size (expo-arms-stripped-upper.rail_slot0_x): the same forging's rail, within this reading's ±."},"rail_slots":{"label":"How many rail slots","kind":"count","measurements":[{"id":"photo","value":13,"unit":"count","source":{"type":"photo","photo":"references/geissele-super-duty-stripped-upper 95a4d20d054e (Aegis Cerakote's z05-1171b_super_duty_receiver_set_black_02: the black set 05-1171B from the right, this upper on its lower, 3292 x 1988)","scaleRef":"the lower's two pin holes, std.ar15.pin_spacing apart (the upper's own lug holes are inside them, on the same axes): each see-through opening fitted as its near rim's circle and its far rim's at once (references/geissele-super-duty-stripped-upper/work/holes.py: rms 0.23 px), their midpoints the frame's points: 341.0 px/in on the mid-plane, a pixel 0.003 in","method":"the see-through gaps along rows 2.04 and 2.06 in, counted (work/rail.py): 13 on each, from 1.22 to 6.14 in the picture","via":"harvest"}}],"note":"Behind the first is a solid run of rail over the charging handle's channel (from rail_rear_x), ahead of the last a long tooth to the front shoulder. Aegis Cerakote's page says \"Markings: Milled T-Marks\" and Primary Arms' assembled upper's \"Milled T-marks\": not seen at the photos' size, and not drawn."},"rail_rear_x":{"label":"The top rail's head: where it begins ahead of the tongue, X (the app draws the head from here)","kind":"length","measurements":[{"id":"standard","value":0.4165,"unit":"in","pm":0.006,"source":{"type":"derived","expr":"{std.ar15.rail_tongue_shoulder_x}","via":"user"}}],"note":"Until 2026-10-20 this was the rail's rearmost point (now rail_tongue_rear_x), and the app drew the head at its full width from there, square: the charging handle's T, cut round for a rounded rail end, stood in its corners. Behind this the rail is the standard's tongue (std.ar15.rail_tongue_*), which the receiver's model carries, as the 22RB's does."},"rail_tongue_rear_x":{"label":"The top rail's tongue: its rounded end's rearmost point, X ahead of the takedown pin","kind":"length","measurements":[{"id":"photo","value":-0.64,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-upper 95a4d20d054e (Aegis Cerakote's z05-1171b_super_duty_receiver_set_black_02: the black set 05-1171B from the right, this upper on its lower, 3292 x 1988)","scaleRef":"the lower's two pin holes, std.ar15.pin_spacing apart (the upper's own lug holes are inside them, on the same axes): each see-through opening fitted as its near rim's circle and its far rim's at once (references/geissele-super-duty-stripped-upper/work/holes.py: rms 0.23 px), their midpoints the frame's points: 341.0 px/in on the mid-plane, a pixel 0.003 in","method":"the rail's tail's rear end in the traced outline (trace.py's x_min over y 1.95 to 2.2: -0.649 ± 0.004); a round end in plan shows its extreme a hundredth behind its tip from a lens ahead of it: -0.638. It stands a little behind the receiver's rear face (-0.621), as the photo shows it over the lower's buffer tower; ± covers the lens and a pixel's few","via":"harvest"}},{"id":"left","value":-0.6,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-upper 36123b52fa05 (Aegis Cerakote's z05-1171b_super_duty_receiver_set_black_01: the black set 05-1171B from the left, this upper on its lower, 3292 x 1988)","scaleRef":"the lower's two pin holes, std.ar15.pin_spacing apart: each see-through opening fitted as its near rim's circle and its far rim's at once (references/geissele-super-duty-stripped-upper/work/holes.py: rms 0.2 px; the pivot's in a window of 56 px, the ear's edge beside it), their midpoints the frame's points (takedown px 2681.05, 936.73; pivot 518.97, 935.46): 339.2 px/in on the mid-plane","method":"the rail's tail's rear end on rows 1.95 to 2.08 in: px 2887, -0.607 in the picture (the frame's check at the other end: the front shoulder's near edge brought back through the lens reads 6.597 to 6.606 for the drawing's 6.591, the thread's near rim 7.005 to 7.022 for the face's 7.036); a round end in plan shows its extreme about a hundredth behind its tip from a lens ahead of it (left_photo_lens_*): -0.60; ± covers that and the frame","via":"harvest"}}],"adopt":{"from":"left","reason":"The two photos of the set disagree by 0.04 on the tail's end, each frame landing on the drawing's front shoulder and face within 0.02. Decided by what the rail has to fit (CLAUDE.md: two readings that can't both be true): the left photo's places the tongue's tip where the catalog's other mil-spec forgings have theirs (-0.57 to -0.59) and where the charging handles on file, made for a mil-spec rail, clear it; the right one's stood the tongue 0.0011 cubic inches into Radian's Raptor SD's T (app/tests/handle-channel.test.ts, 2026-10-28). Both stay here."}},"rail_front_x":{"label":"The top rail's front end ahead of the takedown pin","kind":"length","measurements":[{"id":"shoulder","value":6.591,"unit":"in","pm":0.011,"source":{"type":"derived","expr":"{.front_face_x} - {std.ar15.upper_barrel_thread_length}","via":"harvest"},"note":"The rail's last tooth ends flush with the body's front shoulder, where the barrel-nut thread begins (the photo): the drawing's .445 REF behind the front face."}],"note":"Ahead of it the receiver is the barrel nut's thread."},"receiver_rear_x":{"label":"The receiver's rear face behind the takedown pin (negative)","kind":"length","measurements":[{"id":"standard","value":-0.621,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.ar15.upper_rear_face_x}","via":"harvest"},"note":"The Army's drawing of the upper (8448524). Primary Arms' page for the black set it is sold in (05-1171B): \"Features: Forged 7075-T6 aluminum Hardcoat anodized black Mil-Spec dimensions\", \"It is compatible with Mil-Spec AR-15 parts and accessories\". Its being the Army drawing's receiver is what \"Mil-Spec dimensions\" is taken to say, and each face is tried on its photo."}]},"front_face_x":{"label":"The receiver's front face (the end of its barrel-nut thread) ahead of the takedown pin","kind":"length","measurements":[{"id":"standard","value":7.036,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.ar15.upper_front_face_x}","via":"harvest"},"note":"The Army's drawing: .661 ahead of the pivot lug's hole. Primary Arms' page for the black set it is sold in (05-1171B): \"Features: Forged 7075-T6 aluminum Hardcoat anodized black Mil-Spec dimensions\", \"It is compatible with Mil-Spec AR-15 parts and accessories\". Its being the Army drawing's receiver is what \"Mil-Spec dimensions\" is taken to say, and each face is tried on its photo."},{"id":"right","value":7.03,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-upper 95a4d20d054e (Aegis Cerakote's z05-1171b_super_duty_receiver_set_black_02: the black set 05-1171B from the right, this upper on its lower, 3292 x 1988)","scaleRef":"the lower's two pin holes, std.ar15.pin_spacing apart (the upper's own lug holes are inside them, on the same axes): each see-through opening fitted as its near rim's circle and its far rim's at once (references/geissele-super-duty-stripped-upper/work/holes.py: rms 0.23 px), their midpoints the frame's points: 341.0 px/in on the mid-plane, a pixel 0.003 in","method":"the silhouette's front tip over y 0.6 to 1.2 reads 7.080 (trace.py's x_max): the thread's near rim at the face, about 0.59 nearer than the mid-plane (the chamfer's foot, barrel_thread_minor_d): the lens stands about 28 in away opposite x 4.6, y 3.0 (right_photo_lens_*), so what is z nearer than the mid-plane reads large about that point by 28 / (28 - z): 7.028; ± is the lens's distance and a pixel's few","via":"harvest"}}],"adopt":{"from":"standard","reason":"The drawing dimensions the face; the photo lands on it within its ±."}},"underside_y":{"label":"The receiver's underside above the pin line","kind":"length","measurements":[{"id":"standard","value":0.2485,"unit":"in","pm":0.0015,"source":{"type":"derived","expr":"{std.ar15.deck_y}","via":"harvest"},"note":"It sits on the lower's deck."}]},"width":{"label":"Width of the receiver's body","kind":"length","measurements":[{"id":"tdp","value":1.18,"unit":"in","pm":0.02,"stated":"FORGED DIA 1.18 DIA REF -V-","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 2 of 2, rev G: View G-G; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p109","via":"user"},"note":"The round body just behind the threaded nose, as aero-m4e1-threaded-upper.width reads it. Not measured on this receiver: its page has one photo, of its side."}],"note":"The mil-spec forging's (Primary Arms: \"Mil-Spec dimensions\"). Its forward assist's housing and brass deflector stand out past it on the right."},"notch_bottom_y":{"label":"The notch under the rail's rear end (the charging handle's room), its floor above the pin line","kind":"length","measurements":[{"id":"photo","value":1.58,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-upper 95a4d20d054e (Aegis Cerakote's z05-1171b_super_duty_receiver_set_black_02: the black set 05-1171B from the right, this upper on its lower, 3292 x 1988)","scaleRef":"the lower's two pin holes, std.ar15.pin_spacing apart (the upper's own lug holes are inside them, on the same axes): each see-through opening fitted as its near rim's circle and its far rim's at once (references/geissele-super-duty-stripped-upper/work/holes.py: rms 0.23 px), their midpoints the frame's points: 341.0 px/in on the mid-plane, a pixel 0.003 in","method":"the see-through notch's lower edge in the traced outline (trace.py's y_max over x -0.5 to -0.1, y 1.2 to 1.75: 1.593); from a lens above, what bounds a see-through from below is the wall's far upper edge, 0.32 further than the mid-plane: the lens stands about 28 in away opposite x 4.6, y 3.0 (right_photo_lens_*), so what is z nearer than the mid-plane reads large about that point by 28 / (28 - z): 1.577; ± is the lens's place and a pixel's few","via":"harvest"}}],"note":"The wall's top behind the notch's front wall: what a charging handle's block lies on."},"notch_top_y":{"label":"The notch under the rail's rear end, its roof (the rail's tail's underside) above the pin line","kind":"length","measurements":[{"id":"photo","value":1.91,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-upper 95a4d20d054e (Aegis Cerakote's z05-1171b_super_duty_receiver_set_black_02: the black set 05-1171B from the right, this upper on its lower, 3292 x 1988)","scaleRef":"the lower's two pin holes, std.ar15.pin_spacing apart (the upper's own lug holes are inside them, on the same axes): each see-through opening fitted as its near rim's circle and its far rim's at once (references/geissele-super-duty-stripped-upper/work/holes.py: rms 0.23 px), their midpoints the frame's points: 341.0 px/in on the mid-plane, a pixel 0.003 in","method":"the see-through notch's upper edge in the traced outline, the rail's tail's underside (trace.py's y_min over x -0.45 to -0.1, y 1.75 to 2.05: 1.895); from a lens above, what bounds it from above is the underside's near edge, 0.32 nearer: the lens stands about 28 in away opposite x 4.6, y 3.0 (right_photo_lens_*), so what is z nearer than the mid-plane reads large about that point by 28 / (28 - z): 1.908. The notch is 0.33 high so, for a handle .2985 thick; its middle, 1.74, is the handle's axis on the drawing's tier (1.734) within the ±","via":"harvest"}}]},"charging_handle_above_bore":{"label":"The charging handle's channel above the bore's axis","kind":"length","measurements":[{"id":"standard","value":0.8563,"unit":"in","pm":0.007,"source":{"type":"derived","expr":"{std.ar15.charging_handle_axis_y} - {.bore_axis_above_pin}","via":"user"},"note":"Riding on its guide lugs on the channel's tier: std.ar15.charging_handle_axis_y."}],"note":"The notch the handle's latch end lies in: the handle lies at its height (as expo-arms-stripped-upper.charging_handle_above_bore, 0.87)."},"handle_seat_x":{"label":"The charging handle's seat: the front wall of the open notch under the rail's rear end, ahead of the takedown pin","kind":"length","measurements":[{"id":"tdp","value":0.075,"unit":"in","pm":0.015,"source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: side elevation, scaled (the notch has no callout in this view); user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"},"note":"Scaled, not a callout. On the 6600 px scan the two lug holes, fitted as circles, are 1966 px apart (308.4 px/in over std.ar15.pin_spacing) and the notch's front wall (column 2427.5) is 21.5 px ahead of the takedown hole's centre: 0.070. From the rear face's line, 217 px behind the wall, it is 0.083: the drawing dimensions that face at -0.621 and the scan has it at -0.634 by the holes. Between the two; ± covers both. The notch is 0.31 to 0.32 high there, for the handle's .2985 (drawing 8448518), its front corners cut back 0.06."},{"id":"right","value":0.057,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-upper 95a4d20d054e (Aegis Cerakote's z05-1171b_super_duty_receiver_set_black_02: the black set 05-1171B from the right, this upper on its lower, 3292 x 1988)","scaleRef":"the lower's two pin holes, std.ar15.pin_spacing apart (the upper's own lug holes are inside them, on the same axes): each see-through opening fitted as its near rim's circle and its far rim's at once (references/geissele-super-duty-stripped-upper/work/holes.py: rms 0.23 px), their midpoints the frame's points: 341.0 px/in on the mid-plane, a pixel 0.003 in","method":"the see-through notch's front wall in the traced outline: a straight edge at 0.004 in the picture from y 1.65 to 1.80, between two corners cut back. What bounds a see-through notch at the front, from a lens ahead of it, is the wall's near edge, 0.32 nearer than the mid-plane (the side's face): the lens stands about 28 in away opposite x 4.6, y 3.0 (right_photo_lens_*), so what is z nearer than the mid-plane reads large about that point by 28 / (28 - z): 0.057; ± covers the lens's distance and a pixel's few","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The Army's drawing, scaled; this receiver's own notch reads 0.02 behind it, within both ±, through a lens whose distance is known to a seventh. The notch the model draws is at least the standard's (lib.handle_notch)."},"note":"Where a charging handle stops: the front wall of the notch cut across the receiver under the rail's rear end, open to the rear. The handle's block lies in it with its shoulder against this wall, and the shaft runs on through the slot ahead of it (expo-arms-stripped-upper.handle_seat_x has the photo of one seated)."},"right_photo_lens_distance":{"label":"The side photo: its lens's distance from the receiver's mid-plane","kind":"length","measurements":[{"id":"holes","value":28,"unit":"in","pm":4,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-upper 95a4d20d054e (Aegis Cerakote's z05-1171b_super_duty_receiver_set_black_02: the black set 05-1171B from the right, this upper on its lower, 3292 x 1988)","scaleRef":"the lower's two pin holes, std.ar15.pin_spacing apart (the upper's own lug holes are inside them, on the same axes): each see-through opening fitted as its near rim's circle and its far rim's at once (references/geissele-super-duty-stripped-upper/work/holes.py: rms 0.23 px), their midpoints the frame's points: 341.0 px/in on the mid-plane, a pixel 0.003 in","method":"the lower's two pin holes' far rims stand off their near ones by (49.6, -29.1) px at the takedown pin and (-18.6, -35.0) at the pivot (work/holes.py); the two lines through them meet 32.4 offsets out, which over the lower's 0.88 between its outer faces (std.ar15.lower_body_width) puts the lens 28 in from the mid-plane. Three checks through it: the forward assist's bore, square to its 20 degree axis, shows as an ellipse 0.088 wide (0.083 from 28 in, 0.048 from 20); the front shoulder's near edge reads 6.624 for the drawing's 6.591 (6.621 from 28 in); the thread's near rim 7.080 for the front face (7.088). The rail's gaps' near edges, 2.2% over the standard pitch in the picture, would say 20 in alone: ± covers both","via":"harvest"}}],"note":"A property of Aegis Cerakote's photo 95a4d20d054e, not of the receiver: the model corrects what the right side shows nearer the lens (the forward assist's rear face, the deflector, the hinge lugs) by it."},"right_photo_lens_x":{"label":"The side photo: where its lens stands, X","kind":"length","measurements":[{"id":"holes","value":4.6,"unit":"in","pm":0.5,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-upper 95a4d20d054e (Aegis Cerakote's z05-1171b_super_duty_receiver_set_black_02: the black set 05-1171B from the right, this upper on its lower, 3292 x 1988)","scaleRef":"the lower's two pin holes, std.ar15.pin_spacing apart (the upper's own lug holes are inside them, on the same axes): each see-through opening fitted as its near rim's circle and its far rim's at once (references/geissele-super-duty-stripped-upper/work/holes.py: rms 0.23 px), their midpoints the frame's points: 341.0 px/in on the mid-plane, a pixel 0.003 in","method":"where the lines through the two holes' near and far rims meet (right_photo_lens_distance): px 2235; the rail's gaps are widest about x 4.4 to 5.0 (0.217 against 0.126 at the ends), which is where a lens's axis leaves them least cut down","via":"harvest"}}]},"right_photo_lens_y":{"label":"The side photo: where its lens stands, Y","kind":"length","measurements":[{"id":"holes","value":3,"unit":"in","pm":0.3,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-upper 95a4d20d054e (Aegis Cerakote's z05-1171b_super_duty_receiver_set_black_02: the black set 05-1171B from the right, this upper on its lower, 3292 x 1988)","scaleRef":"the lower's two pin holes, std.ar15.pin_spacing apart (the upper's own lug holes are inside them, on the same axes): each see-through opening fitted as its near rim's circle and its far rim's at once (references/geissele-super-duty-stripped-upper/work/holes.py: rms 0.23 px), their midpoints the frame's points: 341.0 px/in on the mid-plane, a pixel 0.003 in","method":"as right_photo_lens_x: the takedown hole's line gives 2.72, the pivot's 3.29; the rail's top flat shows from above, as it must from a lens over it","via":"harvest"}}]},"body_radius":{"label":"The round body's radius about the bore (the forging's)","kind":"length","measurements":[{"id":"tdp","value":0.59,"unit":"in","pm":0.01,"stated":"FORGED DIA 1.18 DIA REF -V-","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 2 of 2, rev G: View G-G; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p109","via":"user"}},{"id":"model","value":0.6,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): cylindrical faces r 0.6000 about the bore's axis, x -0.43 to 6.59","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's forged figure; the model's is 0.01 more."}},"bore_d":{"label":"The bore the bolt carrier runs in","kind":"length","measurements":[{"id":"tdp","value":1,"unit":"in","pm":0.002,"stated":"DIA -P- (IN 1.000 DIA ±.002 AREA)","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: note 4; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}}]},"dovetail_foot_y":{"label":"The rail's dovetail, its foot (where the neck begins), Y above the pin line","kind":"length","measurements":[{"id":"model","value":1.885,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the planes under the dovetail at y 1.885, z 0.309 to 0.333","via":"user"}}]},"dovetail_foot_half_width":{"label":"The rail's dovetail at its foot, half its width","kind":"length","measurements":[{"id":"model","value":0.333,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the planes at y 1.885 reach z 0.333","via":"user"}},{"id":"std","value":0.323,"unit":"in","pm":0.013,"source":{"type":"derived","expr":"{std.picatinny.bevel_width} / 2 + {std.picatinny.lower_gauge_below_top} - ({.rail_top_above_pin} - {.dovetail_foot_y})","via":"harvest"},"note":"The standard's lower face carried on at its 45 degrees from the lower gauge line (.748 across, .154 below the rail's top) to the height the reference model has the foot at: the face every other rail on file has (the teeth the app draws on this body, a handguard's own rail) and every clamp's channel is cut to. ± is the gauge line's .010 and the model's .003."}],"adopt":{"from":"std","reason":"The standard's: a rail's head is MIL-STD-1913's, and every clamp's channel is cut to it (pipeline/blender/lib.py rail_seat). The reference model draws the same face a hundredth further out, at the standard's stated .164 where the ledger has the middle of .164 -.020 (std.picatinny.lower_gauge_below_top): inside the standard's band, but a body drawn so stands in every clamp (expo-arms-stripped-upper.dovetail_foot_half_width). The model isn't authoritative beside the standard (D49); its neck and the foot's height are still its own."}},"rail_neck_half_width":{"label":"The rail's neck below its dovetail, half its width","kind":"length","measurements":[{"id":"model","value":0.309,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the planes at y 1.700 and 1.885 begin at z 0.309","via":"user"}}]},"rail_neck_bottom_y":{"label":"The rail's neck, where it meets the receiver's sides, Y","kind":"length","measurements":[{"id":"model","value":1.7,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the planes at y 1.700, z 0.309 to 0.319","via":"user"}}]},"side_half_width":{"label":"The receiver's sides below the rail's neck, half its width","kind":"length","measurements":[{"id":"model","value":0.319,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the planes at y 1.700 end at z 0.319; a .10 fillet below them","via":"user"}}]},"side_bottom_y":{"label":"The receiver's sides, where they turn into the round body, Y","kind":"length","measurements":[{"id":"model","value":1.44,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the r .10 fillet between the flat side and the round body, its axis at y 1.440, z 0.419","via":"user"}}]},"lug_wall_half_width":{"label":"The walls below the round body down to the underside, half the width","kind":"length","measurements":[{"id":"model","value":0.453,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the r .075 fillets at y 0.458, their axes at z 0.528","via":"user"}}]},"rear_flange_r":{"label":"The flange round the rear end, its radius about the bore","kind":"length","measurements":[{"id":"model","value":0.6938,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): cylindrical faces r 0.6938 about the bore's axis from the rear face to x -0.470, on both sides","via":"user"}}],"note":"The raised lip that follows the rear end's contour, the forging's."},"rear_flange_front_x":{"label":"The rear flange's front face, X","kind":"length","measurements":[{"id":"model","value":-0.47,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the r 0.6938 faces end at x -0.470","via":"user"}}]},"lug_width":{"label":"The takedown and pivot lugs' width","kind":"length","measurements":[{"id":"tdp","value":0.4945,"unit":"in","pm":0.0015,"stated":".496 -.003 BOTH LUGS","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: the rear elevation; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}}],"note":"The reference model has them 0.494."},"lug_rear_face_top_y":{"label":"The takedown lug's rear face, how high it rises into the body, Y","kind":"length","measurements":[{"id":"model","value":0.458,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/batch123/expo-arms-stripped-upper/cad.py): the plane x -0.236 from y -0.212 to 0.458; the r .75 corner faces lie outside z ±0.247","via":"user"}}],"note":"Behind it the body's lower rear is cut away either side of the lug's width, to the arc a lower's rear walls rise along (std.ar15.rear_wall_arc_r; the upper's own is std.ar15.upper_rear_corner_r)."},"lug_hole_d":{"label":"The lugs' pin holes","kind":"length","measurements":[{"id":"tdp","value":0.251,"unit":"in","pm":0.001,"stated":".250 DIA +.002 THRU (the takedown lug's, CSK .31 DIA X 90 INCL THIS SIDE ONLY); .250 DIA +.001 THRU (the pivot lug's)","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: side elevation; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}}],"note":"The photo's two holes are fitted with this diameter (right_photo_lens_*)."},"barrel_thread_major_d":{"label":"The barrel-nut thread's major diameter","kind":"length","measurements":[{"id":"tdp","value":1.2442,"unit":"in","pm":0.0044,"stated":"1 1/4 -18 UNEF-2A MAJOR DIA - 1.2485/1.2398 (AFTER ANODIZE)","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: plan view, the threaded end; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}},{"id":"photo","value":1.247,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-upper 95a4d20d054e (Aegis Cerakote's z05-1171b_super_duty_receiver_set_black_02: the black set 05-1171B from the right, this upper on its lower, 3292 x 1988)","scaleRef":"the lower's two pin holes, std.ar15.pin_spacing apart (the upper's own lug holes are inside them, on the same axes): each see-through opening fitted as its near rim's circle and its far rim's at once (references/geissele-super-duty-stripped-upper/work/holes.py: rms 0.23 px), their midpoints the frame's points: 341.0 px/in on the mid-plane, a pixel 0.003 in","method":"the threaded nose's top and bottom edges over x 6.7 to 7.0 read 1.498 and 0.251 (trace.py's y_max and y_min), the crests' silhouette; their edges lie close to the mid-plane, so the lens moves them by less than a thousandth","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's thread; the photo's crests land on it within its ±."}},"barrel_thread_minor_d":{"label":"The barrel-nut thread's minor diameter","kind":"length","measurements":[{"id":"tdp","value":1.1803,"unit":"in","pm":0.003,"stated":"MINOR DIA - 1.1803 MAX","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: plan view, the threaded end; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}}]},"barrel_thread_tpi":{"label":"The barrel-nut thread's turns to the inch","kind":"count","measurements":[{"id":"tdp","value":18,"unit":"count","pm":0,"stated":"1 1/4 -18 UNEF-2A","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: plan view, the threaded end; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}}]},"gas_tube_hole_d":{"label":"The gas tube's hole in the front shoulder","kind":"length","measurements":[{"id":"tdp","value":0.1835,"unit":"in","pm":0.0015,"stated":".182 DIA +.003 THRU; .312 DIA +.010 BACK BORE","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 2 of 2, rev G: View F-F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p109","via":"user"}},{"id":"model","value":0.175,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): a cylinder r 0.0875 along x at y 1.662, z 0 (0.783 above the bore), x 6.401 to 6.591","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's callout (D49); the model's hole is 0.008 smaller."},"note":"Above the thread on the bore's mid-plane, std.ar15.gas_tube_above_bore above the bore. Not visible in the set's side photos: the drawing's."},"gas_tube_relief_d":{"label":"The gas tube hole's four corner reliefs, diameter","kind":"length","measurements":[{"id":"tdp","value":0.094,"unit":"in","pm":0.002,"stated":".047 R, 4 PLACES EQUALLY SPACED RANDOM ORIENTATION EXCEPT MUST NOT INTERSECT THREADS","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 2 of 2, rev G: View F-F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p109","via":"user"}},{"id":"model","value":0.09,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): four cylinders r 0.0450 along x round the gas tube's hole","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's radius; the model's is 0.002 less."}},"gas_tube_relief_offset":{"label":"The gas tube hole's corner reliefs, off its centre each way","kind":"length","measurements":[{"id":"model","value":0.078,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): their axes at y 1.585 and 1.740, z ±0.078: 0.0775 and 0.078 off the hole's centre","via":"user"}}]},"port_length":{"label":"The ejection port's length","kind":"length","measurements":[{"id":"tdp","value":3.125,"unit":"in","pm":0.005,"stated":"3.125; .25 R TRUE 2 PLACES; 1.562 ±.010","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: side elevation; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}},{"id":"photo","value":3.09,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-upper 95a4d20d054e (Aegis Cerakote's z05-1171b_super_duty_receiver_set_black_02: the black set 05-1171B from the right, this upper on its lower, 3292 x 1988)","scaleRef":"the lower's two pin holes, std.ar15.pin_spacing apart (the upper's own lug holes are inside them, on the same axes): each see-through opening fitted as its near rim's circle and its far rim's at once (references/geissele-super-duty-stripped-upper/work/holes.py: rms 0.23 px), their midpoints the frame's points: 341.0 px/in on the mid-plane, a pixel 0.003 in","method":"the dark obround's ends in the picture, 2.909 and 6.068, its rim about 0.6 nearer than the mid-plane: the lens stands about 28 in away opposite x 4.6, y 3.0 (right_photo_lens_*), so what is z nearer than the mid-plane reads large about that point by 28 / (28 - z): 2.945 to 6.037","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing dimensions the port; the photo lands on it within its ±."},"note":"The opening reads short of the callout, as it does on Expo Arms' and Aero's photos and on the reference model (3.097): the drawing marks .005 and .042 beside the 3.125's two ends, which may be the opening's own ends inside it."},"port_front_x":{"label":"The ejection port's front end ahead of the takedown pin","kind":"length","measurements":[{"id":"tdp","value":6.036,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{.front_face_x} - 1.00in","via":"user"},"note":"8448524 sheet 1: \"1.00\" from the 3.125's front end to the receiver's front end (read on the scan at 309 px/in: the two extension lines are 1.00 apart)."},{"id":"photo","value":6.04,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-upper 95a4d20d054e (Aegis Cerakote's z05-1171b_super_duty_receiver_set_black_02: the black set 05-1171B from the right, this upper on its lower, 3292 x 1988)","scaleRef":"the lower's two pin holes, std.ar15.pin_spacing apart (the upper's own lug holes are inside them, on the same axes): each see-through opening fitted as its near rim's circle and its far rim's at once (references/geissele-super-duty-stripped-upper/work/holes.py: rms 0.23 px), their midpoints the frame's points: 341.0 px/in on the mid-plane, a pixel 0.003 in","method":"the dark obround's front end in the picture, 6.068, its rim about 0.6 nearer: the lens stands about 28 in away opposite x 4.6, y 3.0 (right_photo_lens_*), so what is z nearer than the mid-plane reads large about that point by 28 / (28 - z): 6.037","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's; the photo lands on it."}},"port_bottom_y":{"label":"The port's lower edge above the pin line, seen from the side (its ends R .25: 0.50 high)","kind":"length","measurements":[{"id":"drawn","value":0.841,"unit":"in","pm":0.01,"source":{"type":"standard","doc":"8448524 sheet 1 side view, scaled (not a callout): its lower straight edge at px row 3640 against the lug holes' row 3900 at the sheet's own 309.3 px/in (the lug holes 6.375 apart), as aero-m4e1-threaded-upper.port_bottom_y read it; a half-size crop reads 0.847 here","via":"user"}},{"id":"photo","value":0.86,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-upper 95a4d20d054e (Aegis Cerakote's z05-1171b_super_duty_receiver_set_black_02: the black set 05-1171B from the right, this upper on its lower, 3292 x 1988)","scaleRef":"the lower's two pin holes, std.ar15.pin_spacing apart (the upper's own lug holes are inside them, on the same axes): each see-through opening fitted as its near rim's circle and its far rim's at once (references/geissele-super-duty-stripped-upper/work/holes.py: rms 0.23 px), their midpoints the frame's points: 341.0 px/in on the mid-plane, a pixel 0.003 in","method":"the dark obround's lower edge in the picture, 0.814, its rim about 0.6 nearer: the lens stands about 28 in away opposite x 4.6, y 3.0 (right_photo_lens_*), so what is z nearer than the mid-plane reads large about that point by 28 / (28 - z): 0.860; its upper edge 1.385, so 0.525 high for the drawing's .25 R ends","via":"harvest"}}],"adopt":{"from":"drawn","reason":"The drawing's; the photo lands within its ±."}},"port_end_r":{"label":"The port's ends' radius (half its height from the side)","kind":"length","measurements":[{"id":"tdp","value":0.25,"unit":"in","pm":0.005,"stated":".25 R TRUE 2 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: side elevation; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}}]},"fa_axis_angle":{"label":"The forward assist's axis, turned inward toward the front in plan","kind":"angle","measurements":[{"id":"tdp","value":20,"unit":"deg","pm":1,"stated":"20°","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: the plan view's forward assist section (CL HOLE at 20°, 1.0285 ±.0050, .509 DIA ±.003, .315 DIA ±.001); user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}}],"note":"The reference model has 22.5 (aero-m4e1-threaded-upper.fa_axis_angle): the drawing wins (D49)."},"fa_bore_d":{"label":"The forward assist's bore","kind":"length","measurements":[{"id":"tdp","value":0.509,"unit":"in","pm":0.003,"stated":".509 DIA ±.003","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: the plan view's forward assist section; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}}]},"fa_bore_depth":{"label":"The forward assist's bore, how deep its .509 runs from the housing's rear face","kind":"length","measurements":[{"id":"tdp","value":0.65,"unit":"in","pm":0.01,"stated":".65","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: the plan view's forward assist section; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}}],"note":"Read as the .509 bore's depth along its axis; ahead of it the hole is the .315."},"fa_inner_bore_d":{"label":"The forward assist's inner bore, ahead of the .509","kind":"length","measurements":[{"id":"tdp","value":0.315,"unit":"in","pm":0.001,"stated":".315 DIA ±.001","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: the plan view's forward assist section; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}}]},"fa_axis_x":{"label":"The forward assist's axis: a point on it, X","kind":"length","measurements":[{"id":"model","value":-0.395,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the r .25 bore's axis through (-0.395, 0.879, 1.090)","via":"user"}}],"note":"With fa_axis_z and the drawing's angle this places the axis; scaled off the drawing's plan view (309 px/in) the hole's centre line is 1.0285 from the receiver's centre line 0.41 ahead of the rear face, which puts it at 1.097 here."},"fa_axis_z":{"label":"The forward assist's axis: that point out from the middle (Z)","kind":"length","measurements":[{"id":"model","value":1.09,"unit":"in","pm":0.01,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the r .25 bore's axis through (-0.395, 0.879, 1.090)","via":"user"}}]},"fa_rear_x":{"label":"The forward assist housing's rear face where the axis crosses it, X","kind":"length","measurements":[{"id":"photo","value":-0.48,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-upper 95a4d20d054e (Aegis Cerakote's z05-1171b_super_duty_receiver_set_black_02: the black set 05-1171B from the right, this upper on its lower, 3292 x 1988)","scaleRef":"the lower's two pin holes, std.ar15.pin_spacing apart (the upper's own lug holes are inside them, on the same axes): each see-through opening fitted as its near rim's circle and its far rim's at once (references/geissele-super-duty-stripped-upper/work/holes.py: rms 0.23 px), their midpoints the frame's points: 341.0 px/in on the mid-plane, a pixel 0.003 in","method":"the forward assist's bore opening, the dark ellipse in its rear face (px 402 to 432, 582 to 762), centred at -0.693 in the picture; the face's centre is on the drawing's axis 1.12 nearer than the mid-plane (fa_axis_z, fa_axis_angle): the lens stands about 28 in away opposite x 4.6, y 3.0 (right_photo_lens_*), so what is z nearer than the mid-plane reads large about that point by 28 / (28 - z): -0.481. Its height reads 0.507 at that depth, the drawing's .509 bore (fa_bore_d), which checks the scale there. The housing's rearmost outline (-0.780 in the picture) is its rim's outer edge; ± covers the lens's distance from 24 to 32 in","via":"harvest"}}],"note":"The housing runs back to the rear end, as the drawing's side view has it and as Expo Arms' forging does (expo-arms-stripped-upper.fa_rear_x: -0.49 on a larger photo); the reference model's stops at -0.34."},"fa_housing_r":{"label":"The forward assist housing's radius about its axis","kind":"length","measurements":[{"id":"model","value":0.3125,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the housing's cylinder r .3125 on the bore's axis","via":"user"}},{"id":"photo","value":0.304,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-upper 95a4d20d054e (Aegis Cerakote's z05-1171b_super_duty_receiver_set_black_02: the black set 05-1171B from the right, this upper on its lower, 3292 x 1988)","scaleRef":"the lower's two pin holes, std.ar15.pin_spacing apart (the upper's own lug holes are inside them, on the same axes): each see-through opening fitted as its near rim's circle and its far rim's at once (references/geissele-super-duty-stripped-upper/work/holes.py: rms 0.23 px), their midpoints the frame's points: 341.0 px/in on the mid-plane, a pixel 0.003 in","method":"the housing's bottom tangent (px 780) is 0.304 below its bore's centre (px 672) at the rear face's depth (the lens stands about 28 in away opposite x 4.6, y 3.0 (right_photo_lens_*), so what is z nearer than the mid-plane reads large about that point by 28 / (28 - z)); its top tangent is lost in the shadowed fillet above it (px 527 to 560), which the rim's feature box leaves out by taking the bottom mirrored about the bore","via":"harvest"}}],"adopt":{"from":"model","reason":"The reference model's; this receiver's photo reads its lower half within the ±."}},"deflector_out":{"label":"The brass deflector's crest, out from the middle (Z; the forging's)","kind":"length","measurements":[{"id":"model","value":1.25,"unit":"in","pm":0.05,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): its crest's faces (a sphere and r .125, r 1.35 cylinders) reach z 1.20 to 1.30 at x 2.31 to 2.34, y 1.11 to 1.32","via":"user"}}],"note":"The mil-spec forging's: no end or top view of this receiver is on file to read its own on."},"deflector_crest_x":{"label":"The deflector's crest, X","kind":"length","measurements":[{"id":"model","value":2.32,"unit":"in","pm":0.02,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): its crest's faces at x 2.308 to 2.337","via":"user"}},{"id":"photo","value":2.35,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-upper 95a4d20d054e (Aegis Cerakote's z05-1171b_super_duty_receiver_set_black_02: the black set 05-1171B from the right, this upper on its lower, 3292 x 1988)","scaleRef":"the lower's two pin holes, std.ar15.pin_spacing apart (the upper's own lug holes are inside them, on the same axes): each see-through opening fitted as its near rim's circle and its far rim's at once (references/geissele-super-duty-stripped-upper/work/holes.py: rms 0.23 px), their midpoints the frame's points: 341.0 px/in on the mid-plane, a pixel 0.003 in","method":"the crease between the deflector's rear face and its slope, the lit band at px 1405 to 1435, centred at 2.249 in the picture; the crest stands about 1.25 out (deflector_out): the lens stands about 28 in away opposite x 4.6, y 3.0 (right_photo_lens_*), so what is z nearer than the mid-plane reads large about that point by 28 / (28 - z): 2.354","via":"harvest"}}],"adopt":{"from":"photo","reason":"This receiver's own crease (the reference model's crest is 0.03 behind it, within both ±): the deflector is its forging's."}},"deflector_front_out":{"label":"The deflector's slope where it ends at the port, out from the middle (Z; the forging's)","kind":"length","measurements":[{"id":"model","value":0.82,"unit":"in","pm":0.03,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): its slope's faces come down to z 0.813 at x 2.886","via":"user"}}]},"hinge_axis_y":{"label":"The port door's hinge pin, Y","kind":"length","measurements":[{"id":"model","value":0.641,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the two lugs' r .0625 holes and r .1365 bosses on one axis at y 0.641, z 0.689","via":"user"}}],"note":"This receiver's photo shows its two hinge lugs about where the model has them (profiles.side, hinge_rear and hinge_front, brought back through the lens): the rear one from 2.82 to 2.94 against the model's 2.837 to 2.932, the front one from 6.12 to 6.29 against 6.079 to 6.235, three pixels ahead. Each is drawn where the photo has it."},"hinge_axis_z":{"label":"The port door's hinge pin, out from the middle (Z)","kind":"length","measurements":[{"id":"model","value":0.689,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): as hinge_axis_y","via":"user"}}]},"hinge_boss_r":{"label":"The hinge lugs' radius about the pin","kind":"length","measurements":[{"id":"model","value":0.1365,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the lugs' cylindrical faces r .1365","via":"user"}}]},"hinge_pin_d":{"label":"The hinge pin's hole","kind":"length","measurements":[{"id":"tdp","value":0.1295,"unit":"in","pm":0.0015,"stated":".128 DIA +.003 THRU 2 HOLES IN LINE","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 2 of 2, rev G: Section B-B; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p109","via":"user"}},{"id":"model","value":0.125,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the lugs' holes r .0625","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's callout; the model's holes are 0.004 smaller."}},"cam_pad_face_z":{"label":"The cam pin's pad on the left side, its face out from the middle (Z, to the left)","kind":"length","measurements":[{"id":"model","value":0.5625,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/batch123/bcm-m4-upper/cad_ch.py): the round along the pad's top edge, r 0.0938 about an axis along x at (y 1.486, z -0.469), so its face at z -0.563; expo-arms-stripped-upper.cam_pad_face_z reads the same file's flat face at z -0.561 to -0.564 over x 4.60 to 5.58, y 1.05 to 1.63","via":"user"}}],"note":"The pad over the cam pin's travel is the forging's: the Army's machined drawing doesn't show it. The left side is drawn as the mil-spec forging's; Aegis Cerakote's left photo of the set (36123b52fa05) is read beside it."},"cam_pad_rear_x":{"label":"The cam pin's pad, its face's rear edge ahead of the takedown pin","kind":"length","measurements":[{"id":"model","value":4.6,"unit":"in","pm":0.01,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/batch123/expo-arms-stripped-upper/cad.py, as expo-arms-stripped-upper.cam_pad_face_z records it): the pad's flat face at z -0.561 to -0.564 over x 4.60 to 5.58, y 1.05 to 1.63","via":"user"}},{"id":"left","value":4.51,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-upper 36123b52fa05 (Aegis Cerakote's z05-1171b_super_duty_receiver_set_black_01: the black set 05-1171B from the left, this upper on its lower, 3292 x 1988)","scaleRef":"the lower's two pin holes, std.ar15.pin_spacing apart: each see-through opening fitted as its near rim's circle and its far rim's at once (references/geissele-super-duty-stripped-upper/work/holes.py: rms 0.2 px; the pivot's in a window of 56 px, the ear's edge beside it), their midpoints the frame's points (takedown px 2681.05, 936.73; pivot 518.97, 935.46): 339.2 px/in on the mid-plane","method":"the pad's rear end, a rise in brightness at px 1138 on row 470: 4.549 in the picture; the lens stands behind the pad, so its rear round is seen whole and this is taken for the round's foot on the flat side, 0.32 nearer than the mid-plane: the lens stands about 25.5 in away opposite x 1.4, y 2.7 (left_photo_lens_*), so what is nearer than the mid-plane by d reads large about that point by 25.5 / (25.5 - d): 4.51","via":"harvest"}}],"adopt":{"from":"model","reason":"The reference model's. This receiver's left photo has the pad's rear end 0.09 further back, read where its round meets the side; which line of a lit round an edge in the picture is isn't settled at that size, so the forging's figure stands and the difference stays visible."},"note":"The left side is drawn as the mil-spec forging's; Aegis Cerakote's left photo of the set (36123b52fa05) is read beside it."},"cam_pad_front_x":{"label":"The cam pin's pad, its face's front edge","kind":"length","measurements":[{"id":"model","value":5.58,"unit":"in","pm":0.01,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/batch123/expo-arms-stripped-upper/cad.py, as expo-arms-stripped-upper.cam_pad_face_z records it): the pad's flat face at z -0.561 to -0.564 over x 4.60 to 5.58, y 1.05 to 1.63","via":"user"}},{"id":"left","value":5.61,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-upper 36123b52fa05 (Aegis Cerakote's z05-1171b_super_duty_receiver_set_black_01: the black set 05-1171B from the left, this upper on its lower, 3292 x 1988)","scaleRef":"the lower's two pin holes, std.ar15.pin_spacing apart: each see-through opening fitted as its near rim's circle and its far rim's at once (references/geissele-super-duty-stripped-upper/work/holes.py: rms 0.2 px; the pivot's in a window of 56 px, the ear's edge beside it), their midpoints the frame's points (takedown px 2681.05, 936.73; pivot 518.97, 935.46): 339.2 px/in on the mid-plane","method":"the pad's front end, a rise in brightness at px 778 to 781 on rows 470 to 560: 5.610 in the picture; seen from behind, the front round is edge-on and this is the face's front edge, 0.56 nearer than the mid-plane: the lens stands about 25.5 in away opposite x 1.4, y 2.7 (left_photo_lens_*), so what is nearer than the mid-plane by d reads large about that point by 25.5 / (25.5 - d): 5.518, and the model's .094 round ahead of it: 5.61","via":"harvest"}}],"adopt":{"from":"model","reason":"The reference model's; this receiver's left photo has the pad's front end within its ± of it."},"note":"The left side is drawn as the mil-spec forging's; Aegis Cerakote's left photo of the set (36123b52fa05) is read beside it."},"cam_pad_bottom_y":{"label":"The cam pin's pad, its face's lower edge above the pin line","kind":"length","measurements":[{"id":"model","value":1.05,"unit":"in","pm":0.01,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/batch123/expo-arms-stripped-upper/cad.py, as expo-arms-stripped-upper.cam_pad_face_z records it): the pad's flat face at z -0.561 to -0.564 over x 4.60 to 5.58, y 1.05 to 1.63","via":"user"}}],"note":"The left side is drawn as the mil-spec forging's; Aegis Cerakote's left photo of the set (36123b52fa05) is read beside it. Its lower edge runs into the round body."},"cam_pad_top_y":{"label":"The cam pin's pad, its face's upper edge","kind":"length","measurements":[{"id":"model","value":1.63,"unit":"in","pm":0.01,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/batch123/expo-arms-stripped-upper/cad.py, as expo-arms-stripped-upper.cam_pad_face_z records it): the pad's flat face at z -0.561 to -0.564 over x 4.60 to 5.58, y 1.05 to 1.63","via":"user"}},{"id":"left","value":1.63,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-upper 36123b52fa05 (Aegis Cerakote's z05-1171b_super_duty_receiver_set_black_01: the black set 05-1171B from the left, this upper on its lower, 3292 x 1988)","scaleRef":"the lower's two pin holes, std.ar15.pin_spacing apart: each see-through opening fitted as its near rim's circle and its far rim's at once (references/geissele-super-duty-stripped-upper/work/holes.py: rms 0.2 px; the pivot's in a window of 56 px, the ear's edge beside it), their midpoints the frame's points (takedown px 2681.05, 936.73; pivot 518.97, 935.46): 339.2 px/in on the mid-plane","method":"the dark band of the pad's upper round, its top edge at px 390 over x 850 to 1050 (the face's own top, px 427, is the round's foot): 1.612 in the picture; the round about 0.45 nearer than the mid-plane: the lens stands about 25.5 in away opposite x 1.4, y 2.7 (left_photo_lens_*), so what is nearer than the mid-plane by d reads large about that point by 25.5 / (25.5 - d): 1.631. The face's top reads 1.53, the model's .094 round under 1.63","via":"harvest"}}],"adopt":{"from":"model","reason":"The reference model's; this receiver's left photo lands on it."},"note":"The left side is drawn as the mil-spec forging's; Aegis Cerakote's left photo of the set (36123b52fa05) is read beside it."},"cam_pad_edge_round":{"label":"The cam pin's pad, the round along its face's edges and at its upper corners","kind":"length","measurements":[{"id":"model","value":0.094,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/batch123/bcm-m4-upper/cad_ch.py): the round along the pad's top edge, r 0.0938 about (y 1.486, z -0.469), and its two upper corners' rounds about z, r 0.0938 at x 4.695 and 5.488","via":"user"}}],"note":"The left side is drawn as the mil-spec forging's; Aegis Cerakote's left photo of the set (36123b52fa05) is read beside it. BCM's forging reads 0.115 on its own photo (bcm-m4-upper.cam_pad_edge_round)."},"latch_slot_wall":{"label":"The charging handle latch's slot in the left wall: the wall left between it and the notch's front wall (handle_seat_x)","kind":"length","measurements":[{"id":"tdp","value":0.156,"unit":"in","pm":0.005,"stated":".156","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: Section D-D (cut along the notch's centre line, View C-C: the left wall at the rear); user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}}],"note":"The left side is drawn as the mil-spec forging's; Aegis Cerakote's left photo of the set (36123b52fa05) is read beside it. As bcm-m4-upper.latch_slot_wall reads the drawing."},"latch_slot_length":{"label":"The latch's slot, along the receiver (its ends full rounds of half this)","kind":"length","measurements":[{"id":"tdp","value":0.195,"unit":"in","pm":0.005,"stated":".195","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: Section D-D (cut along the notch's centre line, View C-C: the left wall at the rear); user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"},"note":"View C-C marks the slot's end FULL R."},{"id":"model","value":0.192,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/batch123/bcm-m4-upper/cad_ch.py): two rounds about z, r 0.0960, at (x 0.329, y 1.616) and (x 0.329, y 1.839), from the wall's face at z -0.318 in to the slot's floor at -0.251; the flat between them from x 0.233 to 0.425","via":"user"}},{"id":"left","value":0.191,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-upper 36123b52fa05 (Aegis Cerakote's z05-1171b_super_duty_receiver_set_black_01: the black set 05-1171B from the left, this upper on its lower, 3292 x 1988)","scaleRef":"the lower's two pin holes, std.ar15.pin_spacing apart: each see-through opening fitted as its near rim's circle and its far rim's at once (references/geissele-super-duty-stripped-upper/work/holes.py: rms 0.2 px; the pivot's in a window of 56 px, the ear's edge beside it), their midpoints the frame's points (takedown px 2681.05, 936.73; pivot 518.97, 935.46): 339.2 px/in on the mid-plane","method":"the dark obround's ends along rows 300 to 400, px 2538 and 2604: 0.421 and 0.227 in the picture; 0.32 nearer: the lens stands about 25.5 in away opposite x 1.4, y 2.7 (left_photo_lens_*), so what is nearer than the mid-plane by d reads large about that point by 25.5 / (25.5 - d): 0.433 and 0.242, 0.191 long, its rear end 0.167 ahead of the notch's front wall (handle_seat_x), the drawing's .156 within the ±","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The drawing's callout; the reference model's is within 0.003 of it."},"note":"The left side is drawn as the mil-spec forging's; Aegis Cerakote's left photo of the set (36123b52fa05) is read beside it. As bcm-m4-upper.latch_slot_length reads the drawing."},"latch_slot_bottom_y":{"label":"The latch's slot, its lower end above the pin line","kind":"length","measurements":[{"id":"model","value":1.52,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/batch123/bcm-m4-upper/cad_ch.py, as bcm-m4-upper.latch_slot_length records it): two rounds about z, r 0.0960, at (x 0.329, y 1.616) and (x 0.329, y 1.839): the slot from y 1.520 to 1.935","via":"user"}},{"id":"left","value":1.54,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-upper 36123b52fa05 (Aegis Cerakote's z05-1171b_super_duty_receiver_set_black_01: the black set 05-1171B from the left, this upper on its lower, 3292 x 1988)","scaleRef":"the lower's two pin holes, std.ar15.pin_spacing apart: each see-through opening fitted as its near rim's circle and its far rim's at once (references/geissele-super-duty-stripped-upper/work/holes.py: rms 0.2 px; the pivot's in a window of 56 px, the ear's edge beside it), their midpoints the frame's points (takedown px 2681.05, 936.73; pivot 518.97, 935.46): 339.2 px/in on the mid-plane","method":"the dark obround's lower end at px 418 to 422 over x 2560 to 2585: 1.523 in the picture; the slot's rim in the flat side, 0.32 nearer than the mid-plane: the lens stands about 25.5 in away opposite x 1.4, y 2.7 (left_photo_lens_*), so what is nearer than the mid-plane by d reads large about that point by 25.5 / (25.5 - d): 1.538","via":"harvest"}}],"adopt":{"from":"model","reason":"The reference model's; this receiver's left photo lands within the ±."},"note":"The left side is drawn as the mil-spec forging's; Aegis Cerakote's left photo of the set (36123b52fa05) is read beside it. Its heights have no callout in the drawing's View C-C or Section D-D: the reference model's."},"latch_slot_top_y":{"label":"The latch's slot, its upper end above the pin line","kind":"length","measurements":[{"id":"model","value":1.935,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/batch123/bcm-m4-upper/cad_ch.py, as bcm-m4-upper.latch_slot_length records it): two rounds about z, r 0.0960, at (x 0.329, y 1.616) and (x 0.329, y 1.839): the slot from y 1.520 to 1.935","via":"user"}},{"id":"left","value":1.95,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-upper 36123b52fa05 (Aegis Cerakote's z05-1171b_super_duty_receiver_set_black_01: the black set 05-1171B from the left, this upper on its lower, 3292 x 1988)","scaleRef":"the lower's two pin holes, std.ar15.pin_spacing apart: each see-through opening fitted as its near rim's circle and its far rim's at once (references/geissele-super-duty-stripped-upper/work/holes.py: rms 0.2 px; the pivot's in a window of 56 px, the ear's edge beside it), their midpoints the frame's points (takedown px 2681.05, 936.73; pivot 518.97, 935.46): 339.2 px/in on the mid-plane","method":"the dark obround's upper end at px 277 to 280: 1.938 in the picture; 0.32 nearer: the lens stands about 25.5 in away opposite x 1.4, y 2.7 (left_photo_lens_*), so what is nearer than the mid-plane by d reads large about that point by 25.5 / (25.5 - d): 1.948","via":"harvest"}}],"adopt":{"from":"model","reason":"The reference model's; this receiver's left photo lands within the ±."},"note":"The left side is drawn as the mil-spec forging's; Aegis Cerakote's left photo of the set (36123b52fa05) is read beside it. Its heights have no callout in the drawing's View C-C or Section D-D: the reference model's."},"takedown_lug_rear_x":{"label":"The takedown lug's rear face, X (from the takedown pin)","kind":"length","measurements":[{"id":"model","value":-0.236,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging; retrieved from the source archive on 2026-10-28)","method":"its faces' vertices below the deck (y < 0.2465) in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; references/geissele-super-duty-stripped-upper/work/lugs.py)","via":"user"}}],"note":"Hidden in every photo on file (inside the lower's rear lug slot): the mil-spec forging's."},"takedown_lug_front_x":{"label":"The takedown lug's front face, X","kind":"length","measurements":[{"id":"model","value":0.226,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging; retrieved from the source archive on 2026-10-28)","method":"its faces' vertices below the deck (y < 0.2465) in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; references/geissele-super-duty-stripped-upper/work/lugs.py)","via":"user"}}],"note":"Hidden in every photo on file: the mil-spec forging's."},"takedown_lug_bottom_y":{"label":"The takedown lug's flat bottom, Y (below the pin line)","kind":"length","measurements":[{"id":"model","value":-0.212,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging; retrieved from the source archive on 2026-10-28)","method":"its faces' vertices below the deck (y < 0.2465) in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; references/geissele-super-duty-stripped-upper/work/lugs.py)","via":"user"}}],"note":"Hidden in every photo on file: the mil-spec forging's."},"pivot_lug_rear_x":{"label":"The pivot lug's rear face, X","kind":"length","measurements":[{"id":"model","value":6.159,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging; retrieved from the source archive on 2026-10-28)","method":"its faces' vertices below the deck (y < 0.2465) in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; references/geissele-super-duty-stripped-upper/work/lugs.py)","via":"user"}}],"note":"Hidden in every photo on file (between the lower's front ears): the mil-spec forging's."},"pivot_lug_front_x":{"label":"The pivot lug's front face, X","kind":"length","measurements":[{"id":"model","value":6.591,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging; retrieved from the source archive on 2026-10-28)","method":"its faces' vertices below the deck (y < 0.2465) in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; references/geissele-super-duty-stripped-upper/work/lugs.py)","via":"user"}}],"note":"Hidden in every photo on file: the mil-spec forging's. It ends at the front shoulder (rail_front_x, 6.591)."},"pivot_lug_r":{"label":"The pivot lug's rounded end, its radius about the pivot pin","kind":"length","measurements":[{"id":"model","value":0.246,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging; retrieved from the source archive on 2026-10-28)","method":"its faces' vertices below the deck (y < 0.2465) in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; references/geissele-super-duty-stripped-upper/work/lugs.py)","via":"user"}}],"note":"Hidden in every photo on file: the mil-spec forging's. Its lowest vertices lie 0.246 below the pin line at x 6.30 and 6.44, on a round about the pin; the edges between the round and the flat faces are broken (vertices at 0.15 below at x 6.22 and 6.54), which the model leaves square."},"left_photo_lens_distance":{"label":"The left photo: its lens's distance from the receiver's mid-plane","kind":"length","measurements":[{"id":"holes","value":25.5,"unit":"in","pm":4,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-upper 36123b52fa05 (Aegis Cerakote's z05-1171b_super_duty_receiver_set_black_01: the black set 05-1171B from the left, this upper on its lower, 3292 x 1988)","scaleRef":"the lower's two pin holes, std.ar15.pin_spacing apart: each see-through opening fitted as its near rim's circle and its far rim's at once (references/geissele-super-duty-stripped-upper/work/holes.py: rms 0.2 px; the pivot's in a window of 56 px, the ear's edge beside it), their midpoints the frame's points (takedown px 2681.05, 936.73; pivot 518.97, 935.46): 339.2 px/in on the mid-plane","method":"the lower's two pin holes' far rims stand off their near ones by (58.2, -33.2) px at the pivot pin and (-14.5, -27.3) at the takedown pin (work/holes.py); the two lines through them meet 29.5 offsets out, which over the lower's 0.88 between its outer faces (std.ar15.lower_body_width) puts the lens 25.5 in from the mid-plane, opposite px (2201, 8). The latch slot's length read through it is the drawing's .195 within 0.004","via":"harvest"}}],"note":"A property of Aegis Cerakote's left photo 36123b52fa05, not of the receiver: the left side's readings are corrected by it."},"left_photo_lens_x":{"label":"The left photo: where its lens stands, X","kind":"length","measurements":[{"id":"holes","value":1.4,"unit":"in","pm":0.5,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-upper 36123b52fa05 (Aegis Cerakote's z05-1171b_super_duty_receiver_set_black_01: the black set 05-1171B from the left, this upper on its lower, 3292 x 1988)","scaleRef":"the lower's two pin holes, std.ar15.pin_spacing apart: each see-through opening fitted as its near rim's circle and its far rim's at once (references/geissele-super-duty-stripped-upper/work/holes.py: rms 0.2 px; the pivot's in a window of 56 px, the ear's edge beside it), their midpoints the frame's points (takedown px 2681.05, 936.73; pivot 518.97, 935.46): 339.2 px/in on the mid-plane","method":"as left_photo_lens_distance: px 2201, 1.41 ahead of the takedown hole","via":"harvest"}}],"note":"A property of Aegis Cerakote's left photo 36123b52fa05, not of the receiver: the left side's readings are corrected by it."},"left_photo_lens_y":{"label":"The left photo: where its lens stands, Y","kind":"length","measurements":[{"id":"holes","value":2.7,"unit":"in","pm":0.4,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-upper 36123b52fa05 (Aegis Cerakote's z05-1171b_super_duty_receiver_set_black_01: the black set 05-1171B from the left, this upper on its lower, 3292 x 1988)","scaleRef":"the lower's two pin holes, std.ar15.pin_spacing apart: each see-through opening fitted as its near rim's circle and its far rim's at once (references/geissele-super-duty-stripped-upper/work/holes.py: rms 0.2 px; the pivot's in a window of 56 px, the ear's edge beside it), their midpoints the frame's points (takedown px 2681.05, 936.73; pivot 518.97, 935.46): 339.2 px/in on the mid-plane","method":"as left_photo_lens_distance: px row 8, 2.74 above the pin line","via":"harvest"}}],"note":"A property of Aegis Cerakote's left photo 36123b52fa05, not of the receiver: the left side's readings are corrected by it."},"deflector_top_wall_y":{"label":"The deflector's top where it meets the receiver's side, Y","kind":"length","measurements":[{"id":"photo","value":1.71,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-upper 95a4d20d054e (Aegis Cerakote's z05-1171b_super_duty_receiver_set_black_02: the black set 05-1171B from the right, this upper on its lower, 3292 x 1988)","scaleRef":"the lower's two pin holes, std.ar15.pin_spacing apart (the upper's own lug holes are inside them, on the same axes): each see-through opening fitted as its near rim's circle and its far rim's at once (references/geissele-super-duty-stripped-upper/work/holes.py: rms 0.23 px), their midpoints the frame's points: 341.0 px/in on the mid-plane, a pixel 0.003 in","method":"the deflector's top: a horizontal line at px 367 over x 1340 to 1650 (the column profiles at x 1420 to 1600 drop from 66 to 30 there), 1.696 in the picture; it is the far edge of the top seen from above, at the side's face, 0.32 nearer than the mid-plane: the lens stands about 28 in away opposite x 4.6, y 3.0 (right_photo_lens_*), so what is z nearer than the mid-plane reads large about that point by 28 / (28 - z): 1.710. The same line runs on ahead of and behind the deflector as the rail's neck's foot","via":"harvest"}},{"id":"neck","value":1.7,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{.rail_neck_bottom_y}","via":"harvest"},"note":"The photo's line is the neck's foot's, the reference model's figure."}],"adopt":{"from":"neck","reason":"The photo has the deflector's top and the neck's foot as one line along the receiver, and reads that line 0.01 over the reference model's neck (1.70), as it reads the rail's top within a hundredth: the line is the neck's."},"note":"From a lens above the rail the deflector's top shows as a dark band, between the line it meets the side along and its outer face's top edge: its top slopes down outward (deflector_top_face_y). The line is one line with the rail's neck's foot, which runs the receiver's length in the same photo. Until 2026-10-28 the deflector was drawn with a flat top at its outline's, read at the deflector's middle depth (1.73), and a red dot's mount on the rail stood in it (app/tests/rail-clamps.test.ts: Aimpoint's T-2 at slot 5, 0.0023 cubic inches)."},"deflector_top_face_y":{"label":"The deflector's top at its outer face, Y","kind":"length","measurements":[{"id":"photo","value":1.67,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-duty-stripped-upper 95a4d20d054e (Aegis Cerakote's z05-1171b_super_duty_receiver_set_black_02: the black set 05-1171B from the right, this upper on its lower, 3292 x 1988)","scaleRef":"the lower's two pin holes, std.ar15.pin_spacing apart (the upper's own lug holes are inside them, on the same axes): each see-through opening fitted as its near rim's circle and its far rim's at once (references/geissele-super-duty-stripped-upper/work/holes.py: rms 0.23 px), their midpoints the frame's points: 341.0 px/in on the mid-plane, a pixel 0.003 in","method":"the outer face's top edge, where the dark band of the deflector's top ends and its lit face begins: px 392 to 403 over x 1420 to 1540, 1.608 in the picture at px 397; about 1.25 nearer than the mid-plane (deflector_out): the lens stands about 28 in away opposite x 4.6, y 3.0 (right_photo_lens_*), so what is z nearer than the mid-plane reads large about that point by 28 / (28 - z): 1.671; ± covers the band's soft lower edge and the lens","via":"harvest"}}]}}},{"subject":"geissele-super-precision-micro-193","title":"Geissele Super Precision T1 Mount - 1.93 in Height (05-543B black, 05-543S DDC)","dimensions":{"optical_axis_above_rail":{"label":"The dot's optical axis above the rail's top (Geissele's height, for an Aimpoint T-2)","kind":"length","measurements":[{"id":"rooftop","value":1.93,"unit":"in","pm":0.005,"stated":"Height: 1.93″ Height to optic centerline","source":{"type":"spec","publisher":"retailer","name":"Rooftop Defense, Geissele Automatics Super Precision Aimpoint Micro T2 Mount, 1.93″ (specifications)","url":"https://www.rooftopdefense.com/product/geissele-automatics-super-precision-aimpoint-micro-t2-mount-1-93/","retrieved":"2026-11-03","via":"harvest"}},{"id":"primary-arms","value":1.93,"unit":"in","pm":0.005,"stated":"Mount Height 1.93 in.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics Super Precision Aimpoint T2 Mount, 1.93\" Height, Black (specifications)","url":"https://www.primaryarms.com/geissele-automatics-super-precision-aimpoint-t2-mount-1.93in-black","retrieved":"2026-11-03","via":"harvest"}},{"id":"kygunco","value":1.93,"unit":"in","pm":0.005,"stated":"Height: 1.93\"","source":{"type":"spec","publisher":"retailer","name":"KYGUNCO, GEISSELE Super Precision Mount -Aimpoint T1 & T1 Black (05-543B)","url":"https://www.kygunco.com/product/geissele-super-precision-mount-aimpoint-t1-t1-black","retrieved":"2026-11-03","via":"harvest"}}],"adopt":{"from":"rooftop","reason":"Three sellers agree; Rooftop Defense says it is to the optic's centerline."},"note":"Rooftop Defense says to what: the optic's centerline. No page names the dot beside the height: Primary Arms titles the product \"Aimpoint T2 Mount\" and lists \"For Aimpoint T2 / T1 and compatible optics\", and its use, \"1.93\\\" central height for gas masks\"; Geissele's text, as Rooftop Defense quotes it, names the T1. Taken as the T-2's height; a T-1 is taken to stand as high, which no page on file says."},"deck_above_rail":{"label":"The deck's top (the floor between the plate's two fences, where a dot's base sits) above the rail's top","kind":"length","measurements":[{"id":"height-less-t2","value":1.341,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.optical_axis_above_rail} - {aimpoint-micro-t-2.axis_above_base}","via":"harvest"},"note":"1.93 in less the T-2's 0.589 in."},{"id":"photos","value":1.295,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.fence_top_above_rail} - {.fence_height}","via":"harvest"},"note":"1.370 in less 0.075 in, read on this height's photos."}],"adopt":{"from":"height-less-t2","reason":"The maker's height less the T-2's own puts the T-2's axis at 1.93 in, which three sellers agree it is sold for; the photos' reading agrees within the two ±."},"note":"Worked out (D101) from the maker's height less the T-2's own axis over its base; this height's photos read it 0.046 in lower, within the two ±."},"fence_top_above_rail":{"label":"The plate's top (its two fences along the sides) above the rail's top","kind":"length","measurements":[{"id":"side","value":1.37,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 c8fa7e8075ca (Primary Arms, the DDC 05-543S's right side, square on, 2200 x 1467)","scaleRef":"the base along the rail, mount_length 1.37 in, over its widest (columns 594 to 1589): 726.3 px/in; square on (no top face shows)","method":"the plate's top (row 133) to the foot at the base's ends (row 1327): 1194 px, 1.644 in; less clamp_below_rail (0.274)","via":"harvest"}}]},"fence_height":{"label":"How far the fences along the plate's two sides stand above the floor between them","kind":"length","measurements":[{"id":"end","value":0.075,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 284b2ff50787 (Rooftop Defense, the DDC 05-543S from the front and above, a little to its right, 1080 x 1080)","scaleRef":"the plate's end face, columns 280 to 696, for its 1.049 in (396.6 px/in across); heights by the side view's 1.644 in from the foot to the fences' top (rows 880 and 250 here: 383 px/in, foreshortened)","method":"the notch in the plate's end face between the two fences, rows 262 to 290","via":"harvest"}}],"note":"Not drawn (geometry.approximations)."},"plate_length":{"label":"The plate (the deck) along the rail","kind":"length","measurements":[{"id":"side","value":1.872,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 c8fa7e8075ca (Primary Arms, the DDC 05-543S's right side, square on, 2200 x 1467)","scaleRef":"the base along the rail, mount_length 1.37 in, over its widest (columns 594 to 1589): 726.3 px/in; square on (no top face shows)","method":"the plate's ends, columns 413 and 1773: 1360 px","via":"harvest"}}]},"plate_bottom_above_rail":{"label":"The plate's underside above the rail's top","kind":"length","measurements":[{"id":"side","value":1.068,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 c8fa7e8075ca (Primary Arms, the DDC 05-543S's right side, square on, 2200 x 1467)","scaleRef":"the base along the rail, mount_length 1.37 in, over its widest (columns 594 to 1589): 726.3 px/in; square on (no top face shows)","method":"the plate's foot, row 352 (1.342 in over the foot), less clamp_below_rail","via":"harvest"}}]},"plate_chamfer_height":{"label":"The chamfer along each of the plate's long lower edges: its height","kind":"length","measurements":[{"id":"side","value":0.07,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 c8fa7e8075ca (Primary Arms, the DDC 05-543S's right side, square on, 2200 x 1467)","scaleRef":"the base along the rail, mount_length 1.37 in, over its widest (columns 594 to 1589): 726.3 px/in; square on (no top face shows)","method":"the plate's lower ends round in from row 300 to its foot at row 352","via":"harvest"}}]},"plate_chamfer_width":{"label":"The chamfer along each of the plate's long lower edges: how far in","kind":"length","measurements":[{"id":"side","value":0.06,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 c8fa7e8075ca (Primary Arms, the DDC 05-543S's right side, square on, 2200 x 1467)","scaleRef":"the base along the rail, mount_length 1.37 in, over its widest (columns 594 to 1589): 726.3 px/in; square on (no top face shows)","method":"the plate's lower ends round in from column 413 to 456 at its foot","via":"harvest"}}]},"plate_left_z":{"label":"The plate's left (nut-side) edge, out from the rail's middle","kind":"length","measurements":[{"id":"bottom","value":0.434,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 f18f5ba7abc4 (Rooftop Defense, the DDC 05-543S from below, 1080 x 1080, the base along the picture's height)","scaleRef":"the base's 1.37 in over its right jaw (rows 318 to 830): 373.7 px/in at the base's depth; the plate, further from the lens, by its own 1.872 in (rows 210 to 858): 346 px/in","method":"the plate's nut-side edge (column 645) to the middle of its four screw holes (495), at the plate's 346 px/in","via":"harvest"}}]},"plate_right_z":{"label":"The plate's right (bolt-head side) edge, out from the rail's middle","kind":"length","measurements":[{"id":"bottom","value":0.616,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 f18f5ba7abc4 (Rooftop Defense, the DDC 05-543S from below, 1080 x 1080, the base along the picture's height)","scaleRef":"the base's 1.37 in over its right jaw (rows 318 to 830): 373.7 px/in at the base's depth; the plate, further from the lens, by its own 1.872 in (rows 210 to 858): 346 px/in","method":"the middle of the four screw holes (column 495) to the plate's right edge (282): 213 px. The plate's whole width, 363 px, is 1.049 in at its 1.872 in length (648 px)","via":"harvest"}}]},"screw_x":{"label":"The four screw holes through the plate: out along the rail from the footprint's middle","kind":"length","measurements":[{"id":"sibling-top","value":0.697,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26c4e373c12a (Sportsman's Warehouse, the absolute (05-401) from above: the family's only straight view of the plate's top with its holes sharp, at its own plate's 1.881 in, 324.5 px/in)","scaleRef":"324.5 px/in","method":"the holes' centres, columns 385 and 837 (452 px apart)","via":"harvest"}}],"note":"No view of this height's top is square or sharp enough to read: the 1.93's own views (from below, f18f5ba7abc4: the four holes' counterbores; from the front and above, 284b2ff50787: the four holes, the key and a larger hole) show the same pattern. Read on the absolute's photo from above (geometry.approximations)."},"screw_z":{"label":"The four screw holes: out across the rifle from the footprint's middle","kind":"length","measurements":[{"id":"sibling-top","value":0.191,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26c4e373c12a (Sportsman's Warehouse, the absolute (05-401) from above: the family's only straight view of the plate's top with its holes sharp, at its own plate's 1.881 in, 324.5 px/in)","scaleRef":"324.5 px/in","method":"rows 603 and 727 (124 px apart)","via":"harvest"}}],"note":"No view of this height's top is square or sharp enough to read: the 1.93's own views (from below, f18f5ba7abc4: the four holes' counterbores; from the front and above, 284b2ff50787: the four holes, the key and a larger hole) show the same pattern. Read on the absolute's photo from above (geometry.approximations)."},"screw_hole_d":{"label":"The screw holes' diameter","kind":"length","measurements":[{"id":"sibling-top","value":0.128,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26c4e373c12a (Sportsman's Warehouse, the absolute (05-401) from above: the family's only straight view of the plate's top with its holes sharp, at its own plate's 1.881 in, 324.5 px/in)","scaleRef":"324.5 px/in","method":"the light through each hole, 41.5 px across","via":"harvest"}}],"note":"No view of this height's top is square or sharp enough to read: the 1.93's own views (from below, f18f5ba7abc4: the four holes' counterbores; from the front and above, 284b2ff50787: the four holes, the key and a larger hole) show the same pattern. Read on the absolute's photo from above (geometry.approximations)."},"pocket_x":{"label":"The two larger round holes in the floor, either side of the key: out along the rail from the footprint's middle","kind":"length","measurements":[{"id":"sibling-top","value":0.33,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26c4e373c12a (Sportsman's Warehouse, the absolute (05-401) from above: the family's only straight view of the plate's top with its holes sharp, at its own plate's 1.881 in, 324.5 px/in)","scaleRef":"324.5 px/in","method":"the dark discs' centres, columns 505 and 719","via":"harvest"}}],"note":"No view of this height's top is square or sharp enough to read: the 1.93's own views (from below, f18f5ba7abc4: the four holes' counterbores; from the front and above, 284b2ff50787: the four holes, the key and a larger hole) show the same pattern. Read on the absolute's photo from above (geometry.approximations)."},"pocket_d":{"label":"The two larger round holes' diameter","kind":"length","measurements":[{"id":"sibling-top","value":0.193,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26c4e373c12a (Sportsman's Warehouse, the absolute (05-401) from above: the family's only straight view of the plate's top with its holes sharp, at its own plate's 1.881 in, 324.5 px/in)","scaleRef":"324.5 px/in","method":"each dark disc 62.5 px across","via":"harvest"}}],"note":"No view of this height's top is square or sharp enough to read: the 1.93's own views (from below, f18f5ba7abc4: the four holes' counterbores; from the front and above, 284b2ff50787: the four holes, the key and a larger hole) show the same pattern. Read on the absolute's photo from above (geometry.approximations)."},"screw_counterbore_d":{"label":"The counterbore under each screw hole (from below)","kind":"length","measurements":[{"id":"bottom","value":0.246,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 f18f5ba7abc4 (Rooftop Defense, the DDC 05-543S from below, 1080 x 1080, the base along the picture's height)","scaleRef":"the base's 1.37 in over its right jaw (rows 318 to 830): 373.7 px/in at the base's depth; the plate, further from the lens, by its own 1.872 in (rows 210 to 858): 346 px/in","method":"the dark ring round each hole, about 85 px across at the plate's depth","via":"harvest"}}]},"screw_counterbore_depth":{"label":"The counterbore's depth up into the plate","kind":"length","measurements":[{"id":"assumed","value":0.1,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows the counterbores in section.","via":"harvest"}}]},"pocket_depth":{"label":"The two larger holes' depth below the floor","kind":"length","measurements":[{"id":"assumed","value":0.15,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view shows their depth.","via":"harvest"}}]},"neck_waist_length":{"label":"The neck between the plate and the base, along the rail","kind":"length","measurements":[{"id":"side","value":1.02,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 c8fa7e8075ca (Primary Arms, the DDC 05-543S's right side, square on, 2200 x 1467)","scaleRef":"the base along the rail, mount_length 1.37 in, over its widest (columns 594 to 1589): 726.3 px/in; square on (no top face shows)","method":"columns 720 and 1461, straight from row 444 to 844","via":"harvest"}}]},"neck_waist_above_rail":{"label":"The middle of the neck's straight stretch, above the rail's top","kind":"length","measurements":[{"id":"side","value":0.666,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 c8fa7e8075ca (Primary Arms, the DDC 05-543S's right side, square on, 2200 x 1467)","scaleRef":"the base along the rail, mount_length 1.37 in, over its widest (columns 594 to 1589): 726.3 px/in; square on (no top face shows)","method":"rows 444 to 844, their middle (644: 0.940 in over the foot), less clamp_below_rail","via":"harvest"}}]},"neck_straight_top_above_rail":{"label":"Where the neck's straight sides (seen from the end) end under the plate's fillet, above the rail's top","kind":"length","measurements":[{"id":"end","value":1.02,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 284b2ff50787 (Rooftop Defense, the DDC 05-543S from the front and above, a little to its right, 1080 x 1080)","scaleRef":"the neck's height between the plate's foot (row 429) and its flare's foot (row 620), for plate_bottom_above_rail less neck_bottom_above_rail (0.698 in)","method":"the straight sides begin at row 441","via":"harvest"}}]},"neck_straight_bottom_above_rail":{"label":"Where the neck's straight sides (seen from the end) give way to its flare onto the base, above the rail's top","kind":"length","measurements":[{"id":"end","value":0.58,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 284b2ff50787 (Rooftop Defense, the DDC 05-543S from the front and above, a little to its right, 1080 x 1080)","scaleRef":"as for neck_straight_top_above_rail","method":"the straight sides end at row 561","via":"harvest"}}]},"neck_waist_width":{"label":"The neck across the rifle, along its straight stretch","kind":"length","measurements":[{"id":"end","value":0.459,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 284b2ff50787 (Rooftop Defense, the DDC 05-543S from the front and above, a little to its right, 1080 x 1080)","scaleRef":"the plate's end face, columns 280 to 696, for its 1.049 in (396.6 px/in across); heights by the side view's 1.644 in from the foot to the fences' top (rows 880 and 250 here: 383 px/in, foreshortened)","method":"columns 399 to 581, straight from row 441 to 561. The neck stands about 0.4 in further from the lens than the plate's end face, which reads it a few hundredths narrow","via":"harvest"}}]},"neck_top_width":{"label":"The neck across the rifle where it meets the plate","kind":"length","measurements":[{"id":"end","value":0.5,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 284b2ff50787 (Rooftop Defense, the DDC 05-543S from the front and above, a little to its right, 1080 x 1080)","scaleRef":"the plate's end face, columns 280 to 696, for its 1.049 in (396.6 px/in across); heights by the side view's 1.644 in from the foot to the fences' top (rows 880 and 250 here: 383 px/in, foreshortened)","method":"columns 400 to 595 under the plate's foot, where the neck's fillet into the plate begins","via":"harvest"}}]},"neck_bottom_width":{"label":"The neck across the rifle where it meets the base","kind":"length","measurements":[{"id":"end","value":0.66,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 284b2ff50787 (Rooftop Defense, the DDC 05-543S from the front and above, a little to its right, 1080 x 1080)","scaleRef":"the plate's end face, columns 280 to 696, for its 1.049 in (396.6 px/in across); heights by the side view's 1.644 in from the foot to the fences' top (rows 880 and 250 here: 383 px/in, foreshortened)","method":"where its flare onto the base ends, about row 610; the view's angle has the right side's flare showing","via":"harvest"}}]},"neck_bottom_above_rail":{"label":"Where the neck's flare meets the base, above the rail's top","kind":"length","measurements":[{"id":"side","value":0.37,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 c8fa7e8075ca (Primary Arms, the DDC 05-543S's right side, square on, 2200 x 1467)","scaleRef":"the base along the rail, mount_length 1.37 in, over its widest (columns 594 to 1589): 726.3 px/in; square on (no top face shows)","method":"where the shoulders' slope meets the neck's straight sides, row 860 (0.643 over the foot), less clamp_below_rail","via":"harvest"}}]},"shoulder_top_above_rail":{"label":"Where the base's sloped shoulders (seen from the side) meet the neck, above the rail's top","kind":"length","measurements":[{"id":"side","value":0.369,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 c8fa7e8075ca (Primary Arms, the DDC 05-543S's right side, square on, 2200 x 1467)","scaleRef":"the base along the rail, mount_length 1.37 in, over its widest (columns 594 to 1589): 726.3 px/in; square on (no top face shows)","method":"row 860 at column 720 (0.643 in over the foot), less clamp_below_rail","via":"harvest"}}]},"shoulder_x":{"label":"Where the base's sloped shoulders meet the neck, out along the rail from the base's middle","kind":"length","measurements":[{"id":"side","value":0.512,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 c8fa7e8075ca (Primary Arms, the DDC 05-543S's right side, square on, 2200 x 1467)","scaleRef":"the base along the rail, mount_length 1.37 in, over its widest (columns 594 to 1589): 726.3 px/in; square on (no top face shows)","method":"column 720 to the base's middle (1091.5)","via":"harvest"}}]},"base_end_top_above_rail":{"label":"The top of the base's upright ends (where its sloped shoulders begin), above the rail's top","kind":"length","measurements":[{"id":"side","value":0.028,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 c8fa7e8075ca (Primary Arms, the DDC 05-543S's right side, square on, 2200 x 1467)","scaleRef":"the base along the rail, mount_length 1.37 in, over its widest (columns 594 to 1589): 726.3 px/in; square on (no top face shows)","method":"row 1108 (0.302 over the foot), less clamp_below_rail","via":"harvest"}}]},"base_top_above_rail":{"label":"The base's top beside the neck (seen from the end), above the rail's top","kind":"length","measurements":[{"id":"end","value":0.34,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 284b2ff50787 (Rooftop Defense, the DDC 05-543S from the front and above, a little to its right, 1080 x 1080)","scaleRef":"the plate's end face, columns 280 to 696, for its 1.049 in (396.6 px/in across); heights by the side view's 1.644 in from the foot to the fences' top (rows 880 and 250 here: 383 px/in, foreshortened)","method":"the base's top on its right beside the neck's flare, about row 621","via":"harvest"}}]},"mount_length":{"label":"The base along the rail (at its foot)","kind":"length","measurements":[{"id":"primary-arms","value":1.37,"unit":"in","pm":0.005,"stated":"Covers just 1.37\" of rail space","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics Super Precision Aimpoint T2 Mount, 1.93\" Height, Black (features)","url":"https://www.primaryarms.com/geissele-automatics-super-precision-aimpoint-t2-mount-1.93in-black","retrieved":"2026-11-03","via":"harvest"}}]},"clamp_below_rail":{"label":"The base's foot below the rail's top","kind":"length","measurements":[{"id":"end","value":0.274,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 284b2ff50787 (Rooftop Defense, the DDC 05-543S from the front and above, a little to its right, 1080 x 1080)","scaleRef":"the plate's end face, columns 280 to 696, for its 1.049 in (396.6 px/in across); heights by the side view's 1.644 in from the foot to the fences' top (rows 880 and 250 here: 383 px/in, foreshortened)","method":"the channel's roof, where the light shows through either side of the lug (row 775), to the foot (row 880): 105 of the 630 px from the foot to the fences' top, of the side view's 1.644 in","via":"harvest"}}]},"width_over_nut":{"label":"The mount's width across the rifle, the nut's end to the base's right face","kind":"length","measurements":[{"id":"bottom","value":1.74,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 f18f5ba7abc4 (Rooftop Defense, the DDC 05-543S from below, 1080 x 1080, the base along the picture's height)","scaleRef":"the base's 1.37 in over its right jaw (rows 318 to 830): 373.7 px/in at the base's depth; the plate, further from the lens, by its own 1.872 in (rows 210 to 858): 346 px/in","method":"the base's right face (column 265) to the nut's end (915) at the base's depth","via":"harvest"}}]},"base_right_z":{"label":"The base's right face (the bolt head's), out from the rail's middle","kind":"length","measurements":[{"id":"bottom","value":0.676,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 f18f5ba7abc4 (Rooftop Defense, the DDC 05-543S from below, 1080 x 1080, the base along the picture's height)","scaleRef":"the base's 1.37 in over its right jaw (rows 318 to 830): 373.7 px/in at the base's depth; the plate, further from the lens, by its own 1.872 in (rows 210 to 858): 346 px/in","method":"column 265 to the rail's middle (517.5, between the two jaws' inner edges, 395 and 640)","via":"harvest"}}]},"base_right_upper_z":{"label":"Where the chamfer along the base's top right edge begins on its top, out from the rail's middle","kind":"length","measurements":[{"id":"sibling-end","value":0.611,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 0642ffe614c6 (Primary Arms, the lower 1/3 (05-469) from the front, square on: the family's only straight end view of the base, read at that photo's own 741 px/in)","scaleRef":"741 px/in","method":"column 441 at row 722","via":"harvest"}}],"note":"No straight end view of this height is on file: read on the lower 1/3's (geometry.approximations)."},"base_right_face_top":{"label":"The top of the base's right face (the chamfer's foot), above the rail's top","kind":"length","measurements":[{"id":"sibling-end","value":0.088,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 0642ffe614c6 (Primary Arms, the lower 1/3 (05-469) from the front, square on: the family's only straight end view of the base, read at that photo's own 741 px/in)","scaleRef":"741 px/in","method":"row 885","via":"harvest"}}],"note":"No straight end view of this height is on file: read on the lower 1/3's (geometry.approximations)."},"base_right_face_bottom":{"label":"The foot of the base's right face (where the chamfer under it begins), below the rail's top","kind":"length","measurements":[{"id":"sibling-end","value":0.091,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 0642ffe614c6 (Primary Arms, the lower 1/3 (05-469) from the front, square on: the family's only straight end view of the base, read at that photo's own 741 px/in)","scaleRef":"741 px/in","method":"row 1018","via":"harvest"}}],"note":"No straight end view of this height is on file: read on the lower 1/3's (geometry.approximations)."},"base_right_foot_z":{"label":"Where the chamfer under the base's right face meets the foot, out from the rail's middle","kind":"length","measurements":[{"id":"sibling-end","value":0.494,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 0642ffe614c6 (Primary Arms, the lower 1/3 (05-469) from the front, square on: the family's only straight end view of the base, read at that photo's own 741 px/in)","scaleRef":"741 px/in","method":"column 528 at row 1138","via":"harvest"}}],"note":"No straight end view of this height is on file: read on the lower 1/3's (geometry.approximations)."},"jaw_bottom_below_rail":{"label":"The jaw block's hook's foot below the rail's top","kind":"length","measurements":[{"id":"sibling-end","value":0.183,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 0642ffe614c6 (Primary Arms, the lower 1/3 (05-469) from the front, square on: the family's only straight end view of the base, read at that photo's own 741 px/in)","scaleRef":"741 px/in","method":"row 1086","via":"harvest"}}],"note":"No straight end view of this height is on file: read on the lower 1/3's (geometry.approximations)."},"lug_depth":{"label":"How far the fixed lugs hang below the rail's top","kind":"length","measurements":[{"id":"sibling-end","value":0.084,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 0642ffe614c6 (Primary Arms, the lower 1/3 (05-469) from the front, square on: the family's only straight end view of the base, read at that photo's own 741 px/in)","scaleRef":"741 px/in","method":"the block's top (row 950) to its foot (row 1012)","via":"harvest"}}],"note":"No straight end view of this height is on file: read on the lower 1/3's (geometry.approximations)."},"base_left_z":{"label":"The base's left face above the rail (where the jaw block bears), out from the rail's middle","kind":"length","measurements":[{"id":"bottom","value":0.328,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 f18f5ba7abc4 (Rooftop Defense, the DDC 05-543S from below, 1080 x 1080, the base along the picture's height)","scaleRef":"the base's 1.37 in over its right jaw (rows 318 to 830): 373.7 px/in at the base's depth; the plate, further from the lens, by its own 1.872 in (rows 210 to 858): 346 px/in","method":"the jaw block's inner edge, column 640","via":"harvest"}}]},"jaw_outer_z":{"label":"The jaw block's outer face (where the nut's collar bears), out from the rail's middle","kind":"length","measurements":[{"id":"bottom","value":0.649,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 f18f5ba7abc4 (Rooftop Defense, the DDC 05-543S from below, 1080 x 1080, the base along the picture's height)","scaleRef":"the base's 1.37 in over its right jaw (rows 318 to 830): 373.7 px/in at the base's depth; the plate, further from the lens, by its own 1.872 in (rows 210 to 858): 346 px/in","method":"column 760","via":"harvest"}}]},"jaw_length":{"label":"The jaw block along the rail","kind":"length","measurements":[{"id":"bottom","value":0.731,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 f18f5ba7abc4 (Rooftop Defense, the DDC 05-543S from below, 1080 x 1080, the base along the picture's height)","scaleRef":"the base's 1.37 in over its right jaw (rows 318 to 830): 373.7 px/in at the base's depth; the plate, further from the lens, by its own 1.872 in (rows 210 to 858): 346 px/in","method":"rows 432 to 705","via":"harvest"}}]},"jaw_chamfer":{"label":"The chamfers round the jaw block's top","kind":"length","measurements":[{"id":"bottom","value":0.09,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 f18f5ba7abc4 (Rooftop Defense, the DDC 05-543S from below, 1080 x 1080, the base along the picture's height)","scaleRef":"the base's 1.37 in over its right jaw (rows 318 to 830): 373.7 px/in at the base's depth; the plate, further from the lens, by its own 1.872 in (rows 210 to 858): 346 px/in","method":"the block's hipped top, its chamfers' lines about 35 px in from its edges","via":"harvest"}}]},"bolt_axis_above_rail":{"label":"The cross bolt's axis above the rail's top","kind":"length","measurements":[{"id":"side","value":-0.017,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 c8fa7e8075ca (Primary Arms, the DDC 05-543S's right side, square on, 2200 x 1467)","scaleRef":"the base along the rail, mount_length 1.37 in, over its widest (columns 594 to 1589): 726.3 px/in; square on (no top face shows)","method":"the round head's centre, row 1140 (0.257 in over the foot), less clamp_below_rail","via":"harvest"}}]},"button_d":{"label":"The cross bolt's round head on the right face (marked G)","kind":"length","measurements":[{"id":"side","value":0.35,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 c8fa7e8075ca (Primary Arms, the DDC 05-543S's right side, square on, 2200 x 1467)","scaleRef":"the base along the rail, mount_length 1.37 in, over its widest (columns 594 to 1589): 726.3 px/in; square on (no top face shows)","method":"columns 960 to 1215, its dark rim with it","via":"harvest"}}]},"button_proud":{"label":"How far the bolt's head stands out of the right face","kind":"length","measurements":[{"id":"assumed","value":0.01,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the head shows flush in the views from the front (224af852b6c2, 284b2ff50787).","via":"harvest"}}]},"nut_length":{"label":"The hex nut along the bolt (across the rifle)","kind":"length","measurements":[{"id":"bottom","value":0.241,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 f18f5ba7abc4 (Rooftop Defense, the DDC 05-543S from below, 1080 x 1080, the base along the picture's height)","scaleRef":"the base's 1.37 in over its right jaw (rows 318 to 830): 373.7 px/in at the base's depth; the plate, further from the lens, by its own 1.872 in (rows 210 to 858): 346 px/in","method":"columns 825 to 915","via":"harvest"}}]},"nut_across":{"label":"The hex nut across its flats","kind":"length","measurements":[{"id":"bottom","value":0.551,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 f18f5ba7abc4 (Rooftop Defense, the DDC 05-543S from below, 1080 x 1080, the base along the picture's height)","scaleRef":"the base's 1.37 in over its right jaw (rows 318 to 830): 373.7 px/in at the base's depth; the plate, further from the lens, by its own 1.872 in (rows 210 to 858): 346 px/in","method":"rows 462 to 668, a flat toward the lens","via":"harvest"}}]},"collar_d":{"label":"The round collar between the nut and the jaw block","kind":"length","measurements":[{"id":"bottom","value":0.455,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 f18f5ba7abc4 (Rooftop Defense, the DDC 05-543S from below, 1080 x 1080, the base along the picture's height)","scaleRef":"the base's 1.37 in over its right jaw (rows 318 to 830): 373.7 px/in at the base's depth; the plate, further from the lens, by its own 1.872 in (rows 210 to 858): 346 px/in","method":"rows 480 to 650","via":"harvest"}}]},"collar_length":{"label":"The collar along the bolt","kind":"length","measurements":[{"id":"bottom","value":0.174,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 f18f5ba7abc4 (Rooftop Defense, the DDC 05-543S from below, 1080 x 1080, the base along the picture's height)","scaleRef":"the base's 1.37 in over its right jaw (rows 318 to 830): 373.7 px/in at the base's depth; the plate, further from the lens, by its own 1.872 in (rows 210 to 858): 346 px/in","method":"columns 760 to 825","via":"harvest"}}]},"nut_slot_width":{"label":"The slot across the nut's end","kind":"length","measurements":[{"id":"assumed","value":0.05,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the view from below (f18f5ba7abc4) shows the slot's notch in the nut's end; its width isn't read.","via":"harvest"}}]},"nut_slot_depth":{"label":"The slot's depth into the nut's end","kind":"length","measurements":[{"id":"assumed","value":0.04,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view shows it in section.","via":"harvest"}}]},"lug_spacing":{"label":"The two fixed lugs under the base, each out along the rail from the cross bolt","kind":"length","measurements":[{"id":"std","value":0.394,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{std.picatinny.slot_pitch}","via":"harvest"},"note":"A slot's pitch."},{"id":"bottom","value":0.393,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 f18f5ba7abc4 (Rooftop Defense, the DDC 05-543S from below, 1080 x 1080, the base along the picture's height)","scaleRef":"the base's 1.37 in over its right jaw (rows 318 to 830): 373.7 px/in at the base's depth; the plate, further from the lens, by its own 1.872 in (rows 210 to 858): 346 px/in","method":"the two blocks' middles, rows 421.5 and 715 (293.5 px apart: 0.785 in), the bolt between them","via":"harvest"}}],"adopt":{"from":"std","reason":"Three shear lugs each lie in a slot; the view from below reads the pitch to a thousandth."},"note":"Primary Arms of this one: \"Triple shear lugs for a rock-solid zero\"; from below, two blocks either side of the bolt (one stamped \"193\")."},"lug_length":{"label":"Each fixed lug along the rail","kind":"length","measurements":[{"id":"bottom","value":0.2,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 f18f5ba7abc4 (Rooftop Defense, the DDC 05-543S from below, 1080 x 1080, the base along the picture's height)","scaleRef":"the base's 1.37 in over its right jaw (rows 318 to 830): 373.7 px/in at the base's depth; the plate, further from the lens, by its own 1.872 in (rows 210 to 858): 346 px/in","method":"rows 383 to 460 and 678 to 752 (77 and 74 px)","via":"harvest"}}]},"lug_width":{"label":"Each fixed lug across the rifle","kind":"length","measurements":[{"id":"bottom","value":0.369,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 f18f5ba7abc4 (Rooftop Defense, the DDC 05-543S from below, 1080 x 1080, the base along the picture's height)","scaleRef":"the base's 1.37 in over its right jaw (rows 318 to 830): 373.7 px/in at the base's depth; the plate, further from the lens, by its own 1.872 in (rows 210 to 858): 346 px/in","method":"columns 445 to 583","via":"harvest"}}]},"deck_x":{"label":"The footprint's middle along the deck, ahead of the base's middle","kind":"length","measurements":[{"id":"side","value":0.002,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-193 c8fa7e8075ca (Primary Arms, the DDC 05-543S's right side, square on, 2200 x 1467)","scaleRef":"the base along the rail, mount_length 1.37 in, over its widest (columns 594 to 1589): 726.3 px/in; square on (no top face shows)","method":"the plate's middle (column 1093) against the base's (1091.5)","via":"harvest"}}]},"edge_break":{"label":"The break on the machined edges","kind":"length","measurements":[{"id":"assumed","value":0.008,"unit":"in","pm":0.004,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the edges in the photos are broken, too little to read.","via":"harvest"}}]},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"rooftop","value":2.5,"unit":"oz","pm":0.05,"stated":"Weight: 2.5oz","source":{"type":"spec","publisher":"retailer","name":"Rooftop Defense, Geissele Automatics Super Precision Aimpoint Micro T2 Mount, 1.93″ (specifications)","url":"https://www.rooftopdefense.com/product/geissele-automatics-super-precision-aimpoint-micro-t2-mount-1-93/","retrieved":"2026-11-03","via":"harvest"}},{"id":"sportsmans","value":2.5,"unit":"oz","pm":0.05,"stated":"1.93in Height Weight: 2.5oz","source":{"type":"spec","publisher":"retailer","name":"Sportsman's Warehouse, Geissele Super Precision T1 Mount Absolute Co-Witness (Geissele's weights for the three heights)","url":"https://www.sportsmans.com/hunting-gear-supplies/optics-binoculars-scopes-rangefinders/scope-rings-bases/geissele-super-precision-t1-mount-absolute-co-witness-black-matte-black/p/1787278","retrieved":"2026-11-03","via":"harvest"}},{"id":"kygunco","value":2.6,"unit":"oz","pm":0.05,"stated":"Weight: 2.6 ounces","source":{"type":"spec","publisher":"retailer","name":"KYGUNCO, GEISSELE Super Precision Mount -Aimpoint T1 & T1 Black (05-543B)","url":"https://www.kygunco.com/product/geissele-super-precision-mount-aimpoint-t1-t1-black","retrieved":"2026-11-03","via":"harvest"}}],"adopt":{"from":"rooftop","reason":"Geissele's list as two sellers carry it; KYGUNCO's 2.6 is a tenth over."},"note":"KYGUNCO gives \"Weight: 2.6 ounces\" for 05-543B (and a shipping weight of 1 lb)."}}},{"subject":"geissele-super-precision-micro-absolute","title":"Geissele Super Precision T1 Mount - Absolute Co-Witness (05-401B black, 05-401S DDC)","dimensions":{"optical_axis_above_rail":{"label":"The dot's optical axis above the rail's top (Geissele's height, for an Aimpoint T-2)","kind":"length","measurements":[{"id":"primary-arms","value":1.41,"unit":"in","pm":0.005,"stated":"Mount Height 1.41 in.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics Super Precision Aimpoint T2 Mount - Absolute Cowitness - Black (specifications)","url":"https://www.primaryarms.com/geissele-super-precision-aimpoint-t1-compatible-optic-mount-absolute-cowitness-black-05-401b","retrieved":"2026-11-03","via":"harvest"}},{"id":"drawing","value":1.41,"unit":"in","pm":0.005,"stated":"1.41 (the drawing's side view, from the dot's axis to the rail's top line)","source":{"type":"spec","publisher":"retailer","name":"Charlie's Custom Clones, Geissele Super Precision Aimpoint Micro Mount (for T-1 and T-2): the dimensioned drawing in its gallery (26e224d25e01)","url":"https://charliescustomclones.com/geissele-super-precision-aimpoint-micro-mount-for-t-1-and-t-2/","retrieved":"2026-11-03","via":"harvest"}}],"adopt":{"from":"primary-arms","reason":"Two sellers agree: Primary Arms' spec row and the dimensioned drawing in Charlie's gallery, each quoting Geissele."},"note":"No page names the dot the 1.41 in is for beside the height: Primary Arms titles the product \"Aimpoint T2 Mount\" and lists \"For Aimpoint T2 / T1 and compatible optics\"; Geissele's own description, as Rooftop Defense quotes it, says \"The Super Precision T1 Series was developed specifically to work with the Aimpoint T1 and similarly mounted red dot optics\". The drawing's dot is a Micro with flip caps and the T-2's rotary switch on its right. Taken as the T-2's height (aimpoint-micro-t-2's axis_above_base is the only Micro reading on file); a T-1 is taken to stand as high, which no page on file says."},"deck_above_rail":{"label":"The deck's top (the floor between the plate's two fences, where a dot's base sits) above the rail's top","kind":"length","measurements":[{"id":"height-less-t2","value":0.821,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.optical_axis_above_rail} - {aimpoint-micro-t-2.axis_above_base}","via":"harvest"},"note":"1.41 in less the T-2's 0.589 in."},{"id":"drawing","value":0.788,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{.fence_top_above_rail} - {.fence_height}","via":"harvest"},"note":"0.867 in less 0.079 in, both read on the drawing."}],"adopt":{"from":"height-less-t2","reason":"The maker's height less the T-2's own puts the T-2's axis at 1.41 in, which is what the mount is sold for; the drawing's reading agrees within the two ±."},"note":"Worked out (D101) from the maker's height less the T-2's own axis over its base. The drawing reads it too: the plate's top (its two fences, the line between the dot and the mount in the side view) 0.867 in over the rail, less the 0.079 in the dot's base goes down between the fences in the end view. The two agree within their ± (0.033 in apart)."},"fence_top_above_rail":{"label":"The plate's top (its two fences along the sides) above the rail's top","kind":"length","measurements":[{"id":"drawing","value":0.867,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the dimensioned drawing in Charlie's Custom Clones' gallery, 1200 x 1200)","scaleRef":"the side view's 1.41 and 1.37: 117.35 px/in","method":"the line between the dot's housing and the plate (rows 609.3 to 610.7, its middle 610.0) to the rail's top line (row 711.7): 101.7 px","via":"harvest"}},{"id":"pa-side","value":0.878,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute fee93b489c46 (Primary Arms' black mount, its right side, 2000 x 1333, from about 9 degrees above)","scaleRef":"the base along the rail, mount_length 1.37 in, over its widest (columns 622 to 1389): 559.1 px/in; heights divided by cos 9.4 degrees (the plate's 1.10 in across shows as 100 px of its top)","method":"the near fence's top edge (row 405) to the foot (row 1033): 1.138 in; less clamp_below_rail","via":"harvest"},"note":"A check, from above: the foot is the near edge."}],"adopt":{"from":"drawing","reason":"The drawing is square on; the photo is from above and agrees within its ±."}},"fence_height":{"label":"How far the fences along the plate's two sides stand above the floor between them","kind":"length","measurements":[{"id":"drawing","value":0.079,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the drawing's end view)","scaleRef":"the end view's 1.78: 118.4 px/in","method":"the dot's base, narrower than its housing, goes down between the fences from the plate's top (row 610.7) to row 620.0: 9.3 px","via":"harvest"}}],"note":"Not drawn: every Micro dot on file is drawn with its housing down to its base, wider than the floor between the fences, and would stand in them (geometry.approximations)."},"floor_width":{"label":"The floor between the fences, across the rifle","kind":"length","measurements":[{"id":"drawing","value":0.578,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the drawing's end view)","scaleRef":"118.4 px/in (its 1.78)","method":"the dot's base between the fences, columns 263.3 to 331.7 (68.4 px), centred on the rail's middle (column 297.5)","via":"harvest"}},{"id":"top","value":0.552,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26c4e373c12a (Sportsman's Warehouse, the black mount from above, 1200 x 1200)","scaleRef":"the plate along the rail, plate_length 1.88 in over columns 305 to 915: 324.5 px/in","method":"the fences' inner edges, rows 577 and 756","via":"harvest"}}],"adopt":{"from":"drawing","reason":"The drawing is square on; the photo from above sees the fences' inner edges at their tops."}},"plate_length":{"label":"The plate (the deck) along the rail","kind":"length","measurements":[{"id":"drawing","value":1.881,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the drawing's side view)","scaleRef":"117.35 px/in","method":"the plate's two ends, columns 738.6 and 959.3: 220.7 px, about the base's middle (848.95)","via":"harvest"}},{"id":"pa-side","value":1.891,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute fee93b489c46 (Primary Arms, the right side)","scaleRef":"559.1 px/in (the base's 1.37)","method":"the plate's ends at its near face, columns 471 and 1528: 1057 px","via":"harvest"}}],"adopt":{"from":"drawing","reason":"Square on; the photo, whose plate stands nearer its lens than the base's foot does, reads 0.5% more."}},"plate_bottom_above_rail":{"label":"The plate's underside (its long edges' chamfers' foot) above the rail's top","kind":"length","measurements":[{"id":"drawing","value":0.556,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the drawing's side view)","scaleRef":"117.35 px/in","method":"the plate's lower line, row 646.4, to the rail's top line (711.7): 65.3 px. The end view has it at row 648.3 (0.540)","via":"harvest"}}]},"plate_chamfer_height":{"label":"The chamfer along each of the plate's long lower edges: its height","kind":"length","measurements":[{"id":"drawing","value":0.12,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the drawing)","scaleRef":"117.35 and 118.4 px/in","method":"the side view's band along the plate's foot, rows 630 to 646.4 (0.14 in), and the end view's chamfer, rows 636.7 to 648.3 (0.10 in): their middle","via":"harvest"}}]},"plate_chamfer_width":{"label":"The chamfer along each of the plate's long lower edges: how far in","kind":"length","measurements":[{"id":"drawing","value":0.085,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the drawing's end view)","scaleRef":"118.4 px/in","method":"the plate's side line (column 240.0) to the chamfer's foot (column 250.0)","via":"harvest"}}]},"plate_left_z":{"label":"The plate's left (nut-side) edge, out from the rail's middle","kind":"length","measurements":[{"id":"drawing","value":0.479,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the drawing's end view, from the rear: the nut on the left)","scaleRef":"118.4 px/in","method":"column 240.0 to the rail's middle (296.7)","via":"harvest"}},{"id":"top","value":0.498,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26c4e373c12a (Sportsman's Warehouse, from above)","scaleRef":"324.5 px/in (plate_length)","method":"the plate's nut-side edge (row 505) to the floor's middle (666.5), which the drawing has over the rail's middle","via":"harvest"}}],"adopt":{"from":"drawing","reason":"Square on. Both have the plate wider on the right (the bolt head's side) than on the left: the right edge is 0.611 in out in the drawing and 0.602 in the photo from above."}},"plate_right_z":{"label":"The plate's right (bolt-head side) edge, out from the rail's middle","kind":"length","measurements":[{"id":"drawing","value":0.611,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the drawing's end view)","scaleRef":"118.4 px/in","method":"column 369.0 to the rail's middle (296.7)","via":"harvest"}},{"id":"top","value":0.602,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26c4e373c12a (Sportsman's Warehouse, from above)","scaleRef":"324.5 px/in","method":"the floor's middle (row 666.5) to the plate's right edge (row 862)","via":"harvest"}}],"adopt":{"from":"drawing","reason":"Square on; the photo agrees within its ±."}},"screw_x":{"label":"The four screw holes through the plate (for the dot's screws, from below): out along the rail from the footprint's middle","kind":"length","measurements":[{"id":"top","value":0.697,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26c4e373c12a (Sportsman's Warehouse, from above)","scaleRef":"324.5 px/in","method":"the holes' centres, columns 385 and 837 (452 px apart), about the plate's middle (610)","via":"harvest"}}]},"screw_z":{"label":"The four screw holes: out across the rifle from the footprint's middle","kind":"length","measurements":[{"id":"top","value":0.191,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26c4e373c12a (Sportsman's Warehouse, from above)","scaleRef":"324.5 px/in","method":"rows 603 and 727 (124 px apart) about the floor's middle (665)","via":"harvest"}}]},"screw_hole_d":{"label":"The screw holes' diameter","kind":"length","measurements":[{"id":"top","value":0.128,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26c4e373c12a (Sportsman's Warehouse, from above)","scaleRef":"324.5 px/in","method":"the light seen through each hole, 41.5 px across","via":"harvest"}}]},"screw_counterbore_d":{"label":"The counterbore under each screw hole (from below)","kind":"length","measurements":[{"id":"bottom","value":0.2,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute ed0da8852dab (Primary Arms, the black mount from below, 2000 x 1333)","scaleRef":"the plate's 1.88 in over its 920 px: 489 px/in","method":"the dark ring round each hole, about 100 px across","via":"harvest"}}]},"screw_counterbore_depth":{"label":"The counterbore's depth up into the plate","kind":"length","measurements":[{"id":"assumed","value":0.1,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows the counterbores in section.","via":"harvest"}}]},"pocket_x":{"label":"The two larger round holes in the floor, either side of the key: out along the rail from the footprint's middle","kind":"length","measurements":[{"id":"top","value":0.33,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26c4e373c12a (Sportsman's Warehouse, from above)","scaleRef":"324.5 px/in","method":"the dark discs' centres, columns 505 and 719 (214 px apart), on the floor's middle row (667)","via":"harvest"}}]},"pocket_d":{"label":"The two larger round holes' diameter","kind":"length","measurements":[{"id":"top","value":0.193,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26c4e373c12a (Sportsman's Warehouse, from above)","scaleRef":"324.5 px/in","method":"each dark disc 62.5 px across","via":"harvest"}}]},"pocket_depth":{"label":"The two larger holes' depth below the floor","kind":"length","measurements":[{"id":"assumed","value":0.15,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: they are dark from above, with no light through them, and no view shows their depth.","via":"harvest"}}]},"neck_waist_length":{"label":"The neck between the plate and the base, along the rail at its narrowest","kind":"length","measurements":[{"id":"drawing","value":0.997,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the drawing's side view)","scaleRef":"117.35 px/in","method":"columns 790.5 and 907.5 at row 657","via":"harvest"}},{"id":"pa-side","value":0.994,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute fee93b489c46 (Primary Arms, the right side)","scaleRef":"559.1 px/in","method":"columns 729 and 1285 at rows 628 to 638","via":"harvest"}}],"adopt":{"from":"drawing","reason":"The two agree."}},"neck_waist_above_rail":{"label":"Where the neck is narrowest, above the rail's top","kind":"length","measurements":[{"id":"drawing","value":0.46,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the drawing)","scaleRef":"117.35 px/in","method":"row 657 in the side view (0.466) and 658.3 in the end view (0.455)","via":"harvest"}}]},"neck_waist_width":{"label":"The neck across the rifle at its narrowest","kind":"length","measurements":[{"id":"drawing","value":0.42,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the drawing's end view)","scaleRef":"118.4 px/in","method":"columns 272.7 and 322.3 at row 658.3: 49.7 px, about the rail's middle","via":"harvest"}}]},"neck_top_width":{"label":"The neck across the rifle where it meets the plate","kind":"length","measurements":[{"id":"drawing","value":0.507,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the drawing's end view)","scaleRef":"118.4 px/in","method":"columns 266.7 and 326.7 at row 648.3, the plate's foot","via":"harvest"}}]},"neck_bottom_width":{"label":"The neck across the rifle where it meets the base","kind":"length","measurements":[{"id":"drawing","value":0.62,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the drawing's end view)","scaleRef":"118.4 px/in","method":"columns 260.0 and 333.4 at row 673.3","via":"harvest"}}]},"neck_bottom_above_rail":{"label":"Where the neck's concave sides meet the base, above the rail's top","kind":"length","measurements":[{"id":"drawing","value":0.327,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the drawing's end view)","scaleRef":"117.35 px/in (rows)","method":"row 673.3","via":"harvest"}}]},"shoulder_top_above_rail":{"label":"Where the base's sloped shoulders (seen from the side) meet the neck, above the rail's top","kind":"length","measurements":[{"id":"drawing","value":0.313,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the drawing's side view)","scaleRef":"117.35 px/in","method":"row 675.0","via":"harvest"}}]},"shoulder_x":{"label":"Where the base's sloped shoulders meet the neck, out along the rail from the base's middle","kind":"length","measurements":[{"id":"drawing","value":0.531,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the drawing's side view)","scaleRef":"117.35 px/in","method":"column 786.7 to the base's middle (849.0)","via":"harvest"}}]},"base_end_top_above_rail":{"label":"The top of the base's upright ends (where its sloped shoulders begin), above the rail's top","kind":"length","measurements":[{"id":"drawing","value":0.085,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the drawing's side view)","scaleRef":"117.35 px/in","method":"row 701.7, where the base's end line turns into the shoulder's slope","via":"harvest"}}]},"base_top_above_rail":{"label":"The base's top beside the neck (seen from the end), above the rail's top","kind":"length","measurements":[{"id":"drawing","value":0.282,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the drawing's end view)","scaleRef":"117.35 px/in (rows)","method":"row 678.3, the base's top on the bolt head's side and the jaw block's","via":"harvest"}}]},"mount_length":{"label":"The base along the rail (at its foot)","kind":"length","measurements":[{"id":"primary-arms","value":1.37,"unit":"in","pm":0.005,"stated":"Covers just 1.37\" of rail space","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics Super Precision Aimpoint T2 Mount - Absolute Cowitness - Black (features)","url":"https://www.primaryarms.com/geissele-super-precision-aimpoint-t1-compatible-optic-mount-absolute-cowitness-black-05-401b","retrieved":"2026-11-03","via":"harvest"}},{"id":"drawing","value":1.37,"unit":"in","pm":0.005,"stated":"1.37 (the drawing's side view, the base along the rail)","source":{"type":"spec","publisher":"retailer","name":"Charlie's Custom Clones: the dimensioned drawing in its gallery (26e224d25e01)","url":"https://charliescustomclones.com/geissele-super-precision-aimpoint-micro-mount-for-t-1-and-t-2/","retrieved":"2026-11-03","via":"harvest"}}],"adopt":{"from":"drawing","reason":"Two sellers agree; the drawing says which length it is (the base's, at its foot)."}},"clamp_below_rail":{"label":"The base's foot below the rail's top","kind":"length","measurements":[{"id":"drawing","value":0.264,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the drawing's side view)","scaleRef":"117.35 px/in","method":"the rail's top line (row 711.7) to the base's foot (742.7); the end view has the foot at row 741.7","via":"harvest"}}]},"width_over_nut":{"label":"The mount's width across the rifle, the nut's end to the base's right face","kind":"length","measurements":[{"id":"drawing","value":1.78,"unit":"in","pm":0.005,"stated":"1.78 (the drawing's end view)","source":{"type":"spec","publisher":"retailer","name":"Charlie's Custom Clones: the dimensioned drawing in its gallery (26e224d25e01)","url":"https://charliescustomclones.com/geissele-super-precision-aimpoint-micro-mount-for-t-1-and-t-2/","retrieved":"2026-11-03","via":"harvest"}}]},"base_right_z":{"label":"The base's right face (the bolt head's), out from the rail's middle","kind":"length","measurements":[{"id":"drawing","value":0.676,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the drawing's end view)","scaleRef":"118.4 px/in","method":"column 376.7 (the 1.78's right end) to the rail's middle (296.7)","via":"harvest"}}]},"base_right_upper_z":{"label":"Where the chamfer along the base's top right edge begins on its top, out from the rail's middle","kind":"length","measurements":[{"id":"drawing","value":0.535,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the drawing's end view)","scaleRef":"118.4 px/in","method":"column 360.0","via":"harvest"}}]},"base_right_face_top":{"label":"The top of the base's right face (the chamfer's foot), above the rail's top","kind":"length","measurements":[{"id":"drawing","value":0.183,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the drawing's end view)","scaleRef":"117.35 px/in (rows)","method":"row 690.2","via":"harvest"}}]},"base_right_face_bottom":{"label":"The foot of the base's right face (where the chamfer under it begins), below the rail's top","kind":"length","measurements":[{"id":"drawing","value":0.141,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the drawing's end view)","scaleRef":"117.35 px/in (rows)","method":"row 728.3","via":"harvest"}}]},"base_right_foot_z":{"label":"Where the chamfer under the base's right face meets the foot, out from the rail's middle","kind":"length","measurements":[{"id":"drawing","value":0.563,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the drawing's end view)","scaleRef":"118.4 px/in","method":"column 363.3","via":"harvest"}}]},"base_left_z":{"label":"The base's left face above the rail (behind the jaw block), out from the rail's middle","kind":"length","measurements":[{"id":"drawing","value":0.39,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the drawing's end view)","scaleRef":"118.4 px/in","method":"the base's left line above the jaw block, column 250.5","via":"harvest"}}]},"jaw_outer_z":{"label":"The jaw block's outer face (where the nut's collar bears), out from the rail's middle","kind":"length","measurements":[{"id":"drawing","value":0.69,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the drawing's end view)","scaleRef":"118.4 px/in","method":"column 215.0","via":"harvest"}}]},"jaw_length":{"label":"The jaw block along the rail","kind":"length","measurements":[{"id":"bottom","value":0.69,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute ed0da8852dab (Primary Arms, from below)","scaleRef":"the base's 1.37 in over its right jaw (columns 632 to 1370): 538.7 px/in","method":"the jaw block, columns 785 to 1155","via":"harvest"}}]},"jaw_bottom_below_rail":{"label":"The jaw block's hook's foot below the rail's top","kind":"length","measurements":[{"id":"drawing","value":0.241,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the drawing's end view)","scaleRef":"117.35 px/in (rows)","method":"row 740.0","via":"harvest"}}]},"jaw_chamfer":{"label":"The chamfers round the jaw block's top","kind":"length","measurements":[{"id":"drawing","value":0.09,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the drawing's end view) and d25985149572 (Primary Arms, the left side: the block's hipped top)","scaleRef":"118.4 px/in","method":"the block's outer top corner, cut from column 215 to about 225 and from row 678 to about 688","via":"harvest"}}]},"bolt_axis_above_rail":{"label":"The cross bolt's axis above the rail's top","kind":"length","measurements":[{"id":"drawing","value":0.014,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the drawing)","scaleRef":"117.35 px/in","method":"the \"G\" head's circle's centre (row 710.0) in the side view; the nut's middle (row 710.0) in the end view","via":"harvest"}}]},"button_d":{"label":"The cross bolt's round head on the right face (marked G)","kind":"length","measurements":[{"id":"pa-side","value":0.349,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute fee93b489c46 (Primary Arms, the right side)","scaleRef":"559.1 px/in","method":"columns 905 to 1100","via":"harvest"}},{"id":"drawing","value":0.383,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the drawing's side view)","scaleRef":"117.35 px/in","method":"the circle's outer stroke, columns 826.7 to 871.7","via":"harvest"}}],"adopt":{"from":"pa-side","reason":"The photo's edge is the head's; the drawing's circle is read at its stroke's outside."}},"button_proud":{"label":"How far the bolt's head stands out of the right face","kind":"length","measurements":[{"id":"assumed","value":0.01,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: in Primary Arms' three-quarter views (0d1926ea2276) the head is all but flush; the drawing's end view has it inside the 1.78.","via":"harvest"}}]},"nut_length":{"label":"The hex nut along the bolt (across the rifle)","kind":"length","measurements":[{"id":"drawing","value":0.259,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the drawing's end view)","scaleRef":"118.4 px/in","method":"columns 166.0 to 196.7","via":"harvest"}}]},"nut_across":{"label":"The hex nut across its flats (its height in the end view, a flat on top)","kind":"length","measurements":[{"id":"drawing","value":0.535,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the drawing's end view)","scaleRef":"117.35 px/in (rows)","method":"rows 678.3 to 741.7; Primary Arms' view of the left side (d25985149572) has a flat on top","via":"harvest"}}]},"collar_d":{"label":"The round collar between the nut and the jaw block","kind":"length","measurements":[{"id":"drawing","value":0.479,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the drawing's end view)","scaleRef":"117.35 px/in (rows)","method":"rows 681.7 to 738.3","via":"harvest"}}]},"collar_length":{"label":"The collar along the bolt","kind":"length","measurements":[{"id":"drawing","value":0.155,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the drawing's end view)","scaleRef":"118.4 px/in","method":"columns 196.7 to 215.0","via":"harvest"}}]},"nut_slot_width":{"label":"The slot across the nut's end","kind":"length","measurements":[{"id":"assumed","value":0.05,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: Primary Arms' view of the left side (d25985149572) shows a slot across the nut's end about a tenth of its width; it isn't read to scale.","via":"harvest"}}]},"nut_slot_depth":{"label":"The slot's depth into the nut's end","kind":"length","measurements":[{"id":"assumed","value":0.04,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view shows it in section.","via":"harvest"}}]},"lug_spacing":{"label":"The two fixed lugs under the base, each out along the rail from the cross bolt","kind":"length","measurements":[{"id":"std","value":0.394,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{std.picatinny.slot_pitch}","via":"harvest"},"note":"A slot's pitch."},{"id":"bottom","value":0.36,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute ed0da8852dab (Primary Arms, from below) and 8ecc7f18d3ab (Sportsman's Warehouse, from below)","scaleRef":"the right jaw's 1.37 in: 538.7 px/in and 328.5 px/in","method":"the blocks' middles, columns 793.5 and 1171 about the bolt's 986 (0.36 and 0.34 in) in the first; 476 and 724.5 about 600 (0.38 in) in the second","via":"harvest"}}],"adopt":{"from":"std","reason":"Three shear lugs (Geissele's sentence) each lie in a rail slot, so the two blocks are a whole number of slots from the bolt; the photos from below read about one, short by their lens."},"note":"Geissele, as Primary Arms quotes it: \"Triple shear lugs for a rock-solid zero\"; Rooftop Defense: \"features 3 shear lugs for maximum rigidity and return to zero\". From below the base has two blocks, one either side of the cross bolt, which lies across the middle: three pieces, each in a slot. Read from below they stand 0.35 to 0.38 in out from the bolt, short of a slot's pitch by about what a lens a few inches off makes of the nearer jaw's foot that scales them; three lugs in three slots are a pitch apart."},"lug_length":{"label":"Each fixed lug along the rail","kind":"length","measurements":[{"id":"bottom","value":0.18,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute ed0da8852dab and 8ecc7f18d3ab (from below)","scaleRef":"538.7 and 328.5 px/in","method":"103 px (0.19 in) and 58 px (0.18 in)","via":"harvest"}}]},"lug_width":{"label":"Each fixed lug across the rifle","kind":"length","measurements":[{"id":"drawing","value":0.394,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the drawing's end view)","scaleRef":"118.4 px/in","method":"the block under the base's roof, columns 273.3 to 320.0","via":"harvest"}}]},"lug_depth":{"label":"How far the fixed lugs hang below the rail's top","kind":"length","measurements":[{"id":"drawing","value":0.085,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the drawing's end view)","scaleRef":"117.35 px/in (rows)","method":"the block's foot, row 721.7, below the rail's top line (711.7)","via":"harvest"}}]},"deck_x":{"label":"The footprint's middle along the deck, ahead of the base's middle","kind":"length","measurements":[{"id":"drawing","value":0,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-absolute 26e224d25e01 (the drawing's side view)","scaleRef":"117.35 px/in","method":"the plate's middle (column 848.95) over the base's (849.0); from above (26c4e373c12a) the four screw holes and the key are about the plate's middle","via":"harvest"}}]},"edge_break":{"label":"The break on the machined edges","kind":"length","measurements":[{"id":"assumed","value":0.008,"unit":"in","pm":0.004,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the edges in Primary Arms' photos are broken, too little to read.","via":"harvest"}}]},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"sportsmans","value":2,"unit":"oz","pm":0.1,"stated":"Absolute Cowitness Weight: 2oz","source":{"type":"spec","publisher":"retailer","name":"Sportsman's Warehouse, Geissele Super Precision T1 Mount Absolute Co-Witness Black - Matte Black (Geissele's weights for the three heights)","url":"https://www.sportsmans.com/hunting-gear-supplies/optics-binoculars-scopes-rangefinders/scope-rings-bases/geissele-super-precision-t1-mount-absolute-co-witness-black-matte-black/p/1787278","retrieved":"2026-11-03","via":"harvest"},"note":"Geissele's list as the seller carries it (\"Lower 1/3rd Weight: 2.1oz Absolute Cowitness Weight: 2oz 1.93in Height Weight: 2.5oz\"): read to the tenth of an ounce its siblings are given to."},{"id":"bestpatron","value":79,"unit":"g","pm":1,"stated":"Weight: approx. 79 g (2.8 oz)","source":{"type":"spec","publisher":"retailer","name":"bestpatron.eu, Geissele Aimpoint Micro Mount - Black, Co-Witness","url":"https://www.bestpatron.eu/p/geissele-aimpoint-micro-mount-black-co-witness","retrieved":"2026-11-03","via":"harvest"}}],"adopt":{"from":"sportsmans","reason":"Geissele's list, as a US seller carries it beside its other two heights (2.1 and 2.5 oz, which Rooftop Defense repeats for those two). The model's metal is held against it (the part's test): bestpatron's 79 g is more than the mount's metal as drawn."},"note":"bestpatron.eu (Czech Republic) gives \"approx. 79 g (2.8 oz)\" for 05-401B, more than Geissele's list has for the tallest of the three heights."}}},{"subject":"geissele-super-precision-micro-lower-13","title":"Geissele Super Precision T1 Mount - Lower 1/3 Co-Witness (05-469B black, 05-469S DDC)","dimensions":{"optical_axis_above_rail":{"label":"The dot's optical axis above the rail's top (Geissele's height for this one, for an Aimpoint T-2)","kind":"length","measurements":[{"id":"primary-arms","value":1.59,"unit":"in","pm":0.005,"stated":"Mount Height 1.59 in.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics Super Precision Aimpoint T2 Mount - Lower 1/3 Cowitness - Black (specifications)","url":"https://www.primaryarms.com/geissele-super-precision-aimpoint-t1-compatible-optic-mount-lower-1-3-cowitness","retrieved":"2026-11-03","via":"harvest"},"note":"The DDC page: \"Mount Height Lower 1/3 - 1.59 in\"."},{"id":"rooftop","value":1.7,"unit":"in","pm":0.005,"stated":"Height: 1.70″ Lower 1/3 Cowitness Height to optic centerline","source":{"type":"spec","publisher":"retailer","name":"Rooftop Defense, Geissele Automatics Super Precision Aimpoint Micro T2 Mount, Lower 1/3 (specifications)","url":"https://www.rooftopdefense.com/product/geissele-automatics-super-precision-aimpoint-micro-t2-mount-lower-1-3/","retrieved":"2026-11-03","via":"harvest"}},{"id":"photo-with-t2","value":1.473,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{.deck_above_rail} + {aimpoint-micro-t-2.axis_above_base}","via":"harvest"},"note":"The deck as this height's own photos read it (0.884 in) and the T-2's 0.589 in."}],"adopt":{"from":"photo-with-t2","reason":"This height's own straight photos, read the way that reproduces the absolute's drawing and the 1.93's published height to within 0.04 in, put a T-2's axis at 1.47 to 1.50 in; neither seller's figure fits them (1.59 is 0.1 over, 1.70 0.2). The deck is drawn where the photos have it, and both sellers' figures stay here."},"note":"Two sellers, quoting Geissele, disagree by 0.11 in, and this height's own photos agree with neither. Read on Primary Arms' straight side view of this mount (PN 05-469 on it) at the base's 1.37 in, the plate's top (its fences) stands 0.966 in over the rail (0.982 on its photo of the DDC one); less the fence it is the deck, and with a T-2 on it the axis is 1.473 in. The same reading on the absolute's own drawing gives 1.377 for its published 1.41, and on the 1.93's own photo 1.89 for its 1.93: it runs 0.03 to 0.04 low, which puts this one about 1.50. Primary Arms' 1.59 is 0.09 to 0.12 over that, Rooftop's 1.70 0.20 to 0.23. Geissele's weight list (2.0, 2.1, 2.5 oz for the three heights, as Sportsman's Warehouse carries it) has this one 0.1 oz over the absolute, about what 0.1 to 0.18 in more neck weighs and short of what 0.29 does. Adopted as read: the conflict stays visible here."},"deck_above_rail":{"label":"The deck's top (the floor between the plate's two fences, where a dot's base sits) above the rail's top","kind":"length","measurements":[{"id":"photo","value":0.884,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.fence_top_above_rail} - {.fence_height}","via":"harvest"},"note":"0.966 in less 0.082 in, both read on this height's photos."}]},"fence_top_above_rail":{"label":"The plate's top (its two fences along the sides) above the rail's top","kind":"length","measurements":[{"id":"side","value":0.966,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 066cdfa6fbe5 (Primary Arms, the black 05-469's right side, 2000 x 1333)","scaleRef":"the base along the rail, mount_length 1.37 in, over its widest (columns 512 to 1439): 676.6 px/in; heights divided by cos 5.6 degrees (the near fence's 0.33 in top face shows as 22 px)","method":"the near fence's outer top edge (row 268, under its lit top face, rows 246 to 268) to the foot at the base's ends (row 1091): 823 px, 1.222 in; less clamp_below_rail (0.256). Read the same way, the absolute's photo (fee93b489c46) gives its drawing's 1.131 in over the foot to 0.002 in","via":"harvest"}},{"id":"side-ddc","value":0.982,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 ccb852a64b8d (Primary Arms, the DDC 05-469S's right side, 2000 x 1333, from about 2.6 degrees above)","scaleRef":"the base along the rail, mount_length 1.37 in, over its widest (columns 577 to 1482): 660.6 px/in","method":"the near fence's outer top edge (row 316, under its lit top face, rows 306 to 316) to the foot at the base's ends (row 1134): 818 px, 1.238 in; less clamp_below_rail (0.256)","via":"harvest"}}],"adopt":{"from":"side","reason":"The black one's photo, on which the plate's other sizes were read; the DDC one's agrees within 0.016 in."}},"fence_height":{"label":"How far the fences along the plate's two sides stand above the floor between them","kind":"length","measurements":[{"id":"end","value":0.082,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 0642ffe614c6 (Primary Arms, the black 05-469 from the front, 2000 x 1333)","scaleRef":"741 px/in (the side view's 1.222 in from the foot to the fences' top, rows 1140 and 233 here)","method":"the fences' tops (row 233) to the floor seen between them (row 294)","via":"harvest"}}],"note":"Not drawn (geometry.approximations)."},"floor_width":{"label":"The floor between the fences, across the rifle","kind":"length","measurements":[{"id":"top","value":0.553,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 aa42d318e782 (Primary Arms, the DDC 05-469 from above, 2000 x 1333)","scaleRef":"the plate's 1.879 in over columns 405 to 1560: 614.7 px/in","method":"the fences' inner edges, rows 565 and 905","via":"harvest"}}]},"plate_length":{"label":"The plate (the deck) along the rail","kind":"length","measurements":[{"id":"side","value":1.879,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 066cdfa6fbe5 (the right side)","scaleRef":"676.6 px/in (the base's 1.37)","method":"the plate's ends, columns 334 and 1605: 1271 px","via":"harvest"}}]},"plate_bottom_above_rail":{"label":"The plate's underside (its long edges' chamfers' foot) above the rail's top","kind":"length","measurements":[{"id":"photos","value":0.678,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 066cdfa6fbe5 (side) and 0642ffe614c6 (end)","scaleRef":"676.6 and 741 px/in","method":"the plate's foot at row 458 in the side view (0.940 over the foot) and row 452 in the end view (0.928); their middle, less clamp_below_rail","via":"harvest"}}]},"plate_chamfer_height":{"label":"The chamfer along each of the plate's long lower edges: its height","kind":"length","measurements":[{"id":"end","value":0.11,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 0642ffe614c6 (the end view)","scaleRef":"741 px/in","method":"the left chamfer rows 386 to 450 (0.097 in), the right rows 354 to 450 (0.13): their middle","via":"harvest"}}]},"plate_chamfer_width":{"label":"The chamfer along each of the plate's long lower edges: how far in","kind":"length","measurements":[{"id":"end","value":0.1,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 0642ffe614c6 (the end view)","scaleRef":"741 px/in","method":"the left chamfer columns 1177 to 1245 (0.092 in), the right 453 to 556 (0.139): their middle","via":"harvest"}}]},"plate_left_z":{"label":"The plate's left (nut-side) edge, out from the rail's middle","kind":"length","measurements":[{"id":"end","value":0.475,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 0642ffe614c6 (the end view from the front: the nut on the right)","scaleRef":"741 px/in","method":"column 1246 to the rail's middle (894). From above (aa42d318e782) the floor's middle to the nut-side edge is 0.472","via":"harvest"}}]},"plate_right_z":{"label":"The plate's right (bolt-head side) edge, out from the rail's middle","kind":"length","measurements":[{"id":"end","value":0.595,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 0642ffe614c6 (the end view)","scaleRef":"741 px/in","method":"column 453 to the rail's middle (894). From above (aa42d318e782) 0.610","via":"harvest"}}]},"screw_x":{"label":"The four screw holes through the plate: out along the rail from the footprint's middle","kind":"length","measurements":[{"id":"top","value":0.689,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 aa42d318e782 (from above)","scaleRef":"614.7 px/in","method":"the holes' centres, columns 556 and 1403 (847 px apart)","via":"harvest"}}]},"screw_z":{"label":"The four screw holes: out across the rifle from the footprint's middle","kind":"length","measurements":[{"id":"top","value":0.198,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 aa42d318e782 (from above)","scaleRef":"614.7 px/in","method":"rows 617 and 861 (244 px apart), about the floor's middle","via":"harvest"}}]},"screw_hole_d":{"label":"The screw holes' diameter","kind":"length","measurements":[{"id":"top","value":0.132,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 aa42d318e782 (from above)","scaleRef":"614.7 px/in","method":"the light through each hole, 81 px across","via":"harvest"}}]},"screw_counterbore_d":{"label":"The counterbore under each screw hole (from below)","kind":"length","measurements":[{"id":"bottom","value":0.23,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 db434af2fca3 (Primary Arms, the black 05-469 from below)","scaleRef":"the base's 1.37 in over 825 px: 602 px/in","method":"the dark ring round each hole, about 137 px across","via":"harvest"}}]},"screw_counterbore_depth":{"label":"The counterbore's depth up into the plate","kind":"length","measurements":[{"id":"assumed","value":0.1,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows the counterbores in section.","via":"harvest"}}]},"pocket_x":{"label":"The two larger round holes in the floor, either side of the key: out along the rail from the footprint's middle","kind":"length","measurements":[{"id":"top","value":0.325,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 aa42d318e782 (from above)","scaleRef":"614.7 px/in","method":"the dark discs' centres, columns 783 and 1183 (400 px apart)","via":"harvest"}}]},"pocket_d":{"label":"The two larger round holes' diameter","kind":"length","measurements":[{"id":"top","value":0.198,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 aa42d318e782 (from above)","scaleRef":"614.7 px/in","method":"each dark disc 122 px across","via":"harvest"}}]},"pocket_depth":{"label":"The two larger holes' depth below the floor","kind":"length","measurements":[{"id":"assumed","value":0.15,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view shows their depth.","via":"harvest"}}]},"neck_waist_length":{"label":"The neck between the plate and the base, along the rail at its narrowest","kind":"length","measurements":[{"id":"side","value":1.006,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 066cdfa6fbe5 (the right side)","scaleRef":"676.6 px/in","method":"columns 631 and 1312 at rows 559 to 615","via":"harvest"}}]},"neck_waist_above_rail":{"label":"Where the neck is narrowest, above the rail's top","kind":"length","measurements":[{"id":"photos","value":0.49,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 0642ffe614c6 (end) and 066cdfa6fbe5 (side)","scaleRef":"741 and 676.6 px/in","method":"row 586 in the end view (0.748 over the foot), rows 559 to 615 in the side view (0.745); less clamp_below_rail","via":"harvest"}}]},"neck_waist_width":{"label":"The neck across the rifle at its narrowest","kind":"length","measurements":[{"id":"end","value":0.422,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 0642ffe614c6 (the end view)","scaleRef":"741 px/in","method":"columns 708 and 1021 at rows 570 to 594 (313 px). Its middle (864.5) is 0.04 in to the right of the rail's middle as the jaws and the lug place it; drawn on the rail's middle","via":"harvest"}}]},"neck_top_width":{"label":"The neck across the rifle where it meets the plate","kind":"length","measurements":[{"id":"end","value":0.668,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 0642ffe614c6 (the end view)","scaleRef":"741 px/in","method":"columns 619 and 1114 at row 458, the plate's foot","via":"harvest"}}]},"neck_bottom_width":{"label":"The neck across the rifle where it meets the base","kind":"length","measurements":[{"id":"end","value":0.665,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 0642ffe614c6 (the end view)","scaleRef":"741 px/in","method":"columns 600 and 1093 at row 714","via":"harvest"}}]},"neck_bottom_above_rail":{"label":"Where the neck's concave sides meet the base, above the rail's top","kind":"length","measurements":[{"id":"end","value":0.319,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 0642ffe614c6 (the end view)","scaleRef":"741 px/in","method":"row 714 (0.575 over the foot), less clamp_below_rail","via":"harvest"}}]},"shoulder_top_above_rail":{"label":"Where the base's sloped shoulders (seen from the side) meet its top, above the rail's top","kind":"length","measurements":[{"id":"side","value":0.315,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 066cdfa6fbe5 (the right side)","scaleRef":"676.6 px/in","method":"the shoulder's slope (its near face's edge, columns 563 at row 823 to 512 at row 927) carried up to the base's top as the end view has it","via":"harvest"}}]},"shoulder_x":{"label":"Where the base's sloped shoulders meet its top, out along the rail from the base's middle","kind":"length","measurements":[{"id":"side","value":0.526,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 066cdfa6fbe5 (the right side)","scaleRef":"676.6 px/in","method":"that slope at the base's top, about the base's middle (column 975.5)","via":"harvest"}}]},"base_end_top_above_rail":{"label":"The top of the base's upright ends (where its sloped shoulders begin), above the rail's top","kind":"length","measurements":[{"id":"side","value":-0.013,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 066cdfa6fbe5 (the right side)","scaleRef":"676.6 px/in","method":"row 927 (0.243 over the foot), less clamp_below_rail","via":"harvest"}}]},"base_top_above_rail":{"label":"The base's top beside the neck (seen from the end), above the rail's top","kind":"length","measurements":[{"id":"end","value":0.311,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 0642ffe614c6 (the end view)","scaleRef":"741 px/in","method":"row 720 (0.567 over the foot)","via":"harvest"}}]},"mount_length":{"label":"The base along the rail (at its foot)","kind":"length","measurements":[{"id":"primary-arms","value":1.37,"unit":"in","pm":0.005,"stated":"Covers just 1.37\" of rail space","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Geissele Automatics Super Precision Aimpoint T2 Mount - Lower 1/3 Cowitness - Black (features)","url":"https://www.primaryarms.com/geissele-super-precision-aimpoint-t1-compatible-optic-mount-lower-1-3-cowitness","retrieved":"2026-11-03","via":"harvest"}}]},"clamp_below_rail":{"label":"The base's foot below the rail's top","kind":"length","measurements":[{"id":"end","value":0.256,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 0642ffe614c6 (the end view)","scaleRef":"741 px/in","method":"the lug's top, the channel's roof (row 950), to the foot (row 1140)","via":"harvest"}}]},"width_over_nut":{"label":"The mount's width across the rifle, the nut's end to the base's right face","kind":"length","measurements":[{"id":"end","value":1.68,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 0642ffe614c6 (the end view)","scaleRef":"741 px/in","method":"columns 410 to 1655 (1245 px). The nut is deeper from the lens than the base's end face and reads a few hundredths short","via":"harvest"}}]},"base_right_z":{"label":"The base's right face (the bolt head's), out from the rail's middle","kind":"length","measurements":[{"id":"end","value":0.653,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 0642ffe614c6 (the end view)","scaleRef":"741 px/in","method":"column 410 to the rail's middle (894)","via":"harvest"}}]},"base_right_upper_z":{"label":"Where the base's top right edge's chamfer begins on its top, out from the rail's middle","kind":"length","measurements":[{"id":"end","value":0.611,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 0642ffe614c6 (the end view)","scaleRef":"741 px/in","method":"column 441 at row 722","via":"harvest"}}]},"base_right_face_top":{"label":"The top of the base's right face (the chamfer's foot), above the rail's top","kind":"length","measurements":[{"id":"end","value":0.088,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 0642ffe614c6 (the end view)","scaleRef":"741 px/in","method":"row 885, where the edge comes out to column 410","via":"harvest"}}]},"base_right_face_bottom":{"label":"The foot of the base's right face (where the chamfer under it begins), below the rail's top","kind":"length","measurements":[{"id":"end","value":0.091,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 0642ffe614c6 (the end view)","scaleRef":"741 px/in","method":"row 1018 (0.165 over the foot)","via":"harvest"}}]},"base_right_foot_z":{"label":"Where the chamfer under the base's right face meets the foot, out from the rail's middle","kind":"length","measurements":[{"id":"end","value":0.494,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 0642ffe614c6 (the end view)","scaleRef":"741 px/in","method":"column 528 at row 1138","via":"harvest"}}]},"base_left_z":{"label":"The base's left face above the rail (where the jaw block bears), out from the rail's middle","kind":"length","measurements":[{"id":"end","value":0.345,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 0642ffe614c6 (the end view)","scaleRef":"741 px/in","method":"the body's edge above the jaw block's sloped inner top, about column 1150","via":"harvest"}}]},"jaw_outer_z":{"label":"The jaw block's outer face (where the nut's collar bears), out from the rail's middle","kind":"length","measurements":[{"id":"end","value":0.636,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 0642ffe614c6 (the end view)","scaleRef":"741 px/in","method":"column 1365","via":"harvest"}}]},"jaw_length":{"label":"The jaw block along the rail","kind":"length","measurements":[{"id":"bottom","value":0.738,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 db434af2fca3 (from below)","scaleRef":"602 px/in","method":"rows 437 to 881","via":"harvest"}}]},"jaw_bottom_below_rail":{"label":"The jaw block's hook's foot below the rail's top","kind":"length","measurements":[{"id":"end","value":0.183,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 0642ffe614c6 (the end view)","scaleRef":"741 px/in","method":"row 1086 (0.073 over the foot)","via":"harvest"}}]},"jaw_chamfer":{"label":"The chamfers round the jaw block's top","kind":"length","measurements":[{"id":"end","value":0.09,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 0642ffe614c6 (the end view)","scaleRef":"741 px/in","method":"the block's top outer corner cut about 65 px each way","via":"harvest"}}]},"bolt_axis_above_rail":{"label":"The cross bolt's axis above the rail's top","kind":"length","measurements":[{"id":"side","value":-0.011,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 066cdfa6fbe5 (the right side)","scaleRef":"676.6 px/in","method":"the round head's centre, row 925 (0.245 over the foot), less clamp_below_rail","via":"harvest"}}]},"button_d":{"label":"The cross bolt's round head on the right face (marked G)","kind":"length","measurements":[{"id":"side","value":0.272,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 066cdfa6fbe5 (the right side)","scaleRef":"676.6 px/in","method":"columns 868 to 1052","via":"harvest"}}]},"button_proud":{"label":"How far the bolt's head stands out of the right face","kind":"length","measurements":[{"id":"assumed","value":0.01,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the end view (0642ffe614c6) has the head inside the face's line.","via":"harvest"}}]},"nut_length":{"label":"The hex nut along the bolt (across the rifle)","kind":"length","measurements":[{"id":"end","value":0.236,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 0642ffe614c6 (the end view)","scaleRef":"741 px/in","method":"columns 1480 to 1655","via":"harvest"}}]},"nut_across":{"label":"The hex nut across its flats (its height in the end view, a flat on top)","kind":"length","measurements":[{"id":"end","value":0.529,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 0642ffe614c6 (the end view)","scaleRef":"741 px/in","method":"rows 718 to 1110. nbg.eu of this mount: \"The clamping nut is tightened with a ½″ wrench\"","via":"harvest"}}]},"collar_d":{"label":"The round collar between the nut and the jaw block","kind":"length","measurements":[{"id":"end","value":0.43,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 0642ffe614c6 (the end view)","scaleRef":"741 px/in","method":"the round collar, about rows 760 to 1065, read by eye: its edges are dark on the nut's","via":"harvest"}}]},"collar_length":{"label":"The collar along the bolt","kind":"length","measurements":[{"id":"end","value":0.155,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 0642ffe614c6 (the end view)","scaleRef":"741 px/in","method":"columns 1365 to 1480","via":"harvest"}}]},"nut_slot_width":{"label":"The slot across the nut's end","kind":"length","measurements":[{"id":"assumed","value":0.05,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the end view (0642ffe614c6) shows the slot's two notches in the nut's end; its width isn't read.","via":"harvest"}}]},"nut_slot_depth":{"label":"The slot's depth into the nut's end","kind":"length","measurements":[{"id":"assumed","value":0.04,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view shows it in section.","via":"harvest"}}]},"lug_spacing":{"label":"The two fixed lugs under the base, each out along the rail from the cross bolt","kind":"length","measurements":[{"id":"std","value":0.394,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{std.picatinny.slot_pitch}","via":"harvest"},"note":"A slot's pitch."},{"id":"bottom","value":0.404,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 db434af2fca3 (from below)","scaleRef":"602 px/in","method":"the stamped block's middle (row 419) to the bolt's (row 662); the other block is too dark to read","via":"harvest"}}],"adopt":{"from":"std","reason":"Three shear lugs each lie in a slot; the photo reads one pitch."},"note":"Primary Arms of this one: \"Triple shear lugs for a rock-solid zero\". Three lugs, each in a slot, are a pitch apart; from below, the rear block (stamped \"1/3\") stands a pitch from the bolt."},"lug_length":{"label":"Each fixed lug along the rail","kind":"length","measurements":[{"id":"bottom","value":0.188,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 db434af2fca3 (from below)","scaleRef":"602 px/in","method":"the stamped block, rows 362 to 475","via":"harvest"}}]},"lug_width":{"label":"Each fixed lug across the rifle","kind":"length","measurements":[{"id":"end","value":0.367,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 0642ffe614c6 (the end view)","scaleRef":"741 px/in","method":"the block under the roof, columns 760 to 1032","via":"harvest"}}]},"lug_depth":{"label":"How far the fixed lugs hang below the rail's top","kind":"length","measurements":[{"id":"end","value":0.084,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 0642ffe614c6 (the end view)","scaleRef":"741 px/in","method":"the block's top (row 950) to its foot (row 1012)","via":"harvest"}}]},"deck_x":{"label":"The footprint's middle along the deck, ahead of the base's middle","kind":"length","measurements":[{"id":"side","value":-0.009,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/geissele-super-precision-micro-lower-13 066cdfa6fbe5 (the right side)","scaleRef":"676.6 px/in","method":"the plate's middle (column 969.5) against the base's (975.5); from above (aa42d318e782) the screw holes' middle is the plate's","via":"harvest"}}]},"edge_break":{"label":"The break on the machined edges","kind":"length","measurements":[{"id":"assumed","value":0.008,"unit":"in","pm":0.004,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the edges in Primary Arms' photos are broken, too little to read.","via":"harvest"}}]},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"rooftop","value":2.1,"unit":"oz","pm":0.05,"stated":"Weight: 2.1oz","source":{"type":"spec","publisher":"retailer","name":"Rooftop Defense, Geissele Automatics Super Precision Aimpoint Micro T2 Mount, Lower 1/3 (specifications)","url":"https://www.rooftopdefense.com/product/geissele-automatics-super-precision-aimpoint-micro-t2-mount-lower-1-3/","retrieved":"2026-11-03","via":"harvest"}},{"id":"nbg","value":60,"unit":"g","pm":0.5,"stated":"Weight: 60 g (2.1 oz)","source":{"type":"spec","publisher":"retailer","name":"nbg.eu, Geissele Super Precision T1 Mount - Lower 1/3 Co-Witness","url":"https://nbg.eu/product/super-precision-t1-mount-lower-1-3-co-witness/","retrieved":"2026-11-03","via":"harvest"}},{"id":"sportsmans","value":2.1,"unit":"oz","pm":0.05,"stated":"Lower 1/3rd Weight: 2.1oz","source":{"type":"spec","publisher":"retailer","name":"Sportsman's Warehouse, Geissele Super Precision T1 Mount Absolute Co-Witness (Geissele's weights for the three heights)","url":"https://www.sportsmans.com/hunting-gear-supplies/optics-binoculars-scopes-rangefinders/scope-rings-bases/geissele-super-precision-t1-mount-absolute-co-witness-black-matte-black/p/1787278","retrieved":"2026-11-03","via":"harvest"}}],"adopt":{"from":"rooftop","reason":"Three sellers carry Geissele's 2.1 oz (nbg.eu's 60 g is the same figure in grams)."}}}},{"subject":"guntec-ar15-carbine-buffer","title":"Guntec USA AR-15 Mil-Spec Car Buffer (CARBUF)","dimensions":{"weight":{"label":"Weight (its class: carbine, H, H2…)","kind":"mass","measurements":[{"id":"guntec","value":3,"unit":"oz","pm":0.05,"stated":"3.0 oz weight","source":{"type":"spec","publisher":"manufacturer","name":"Guntec USA, AR-15 Mil-Spec Car Buffer, CARBUF, its description (\"CAR/M4 Mil-Spec Buffer Steel Weights 3.0 oz weight Aluminum Body, White Neoprene Head\"); the page as the user saved it, references/guntec-ar15-carbine-buffer/docs/ar-15-mil-spec-car-buffer.saved-2026-10-20.html","url":"https://guntecusa.com/product/ar-15-mil-spec-car-buffer/","retrieved":"2026-10-20","via":"user"}},{"id":"mgw-set","value":3,"unit":"oz","pm":0.5,"stated":"End Plate, Castle Nut, 3 oz CAR Buffer Chrome Silicon Spring","source":{"type":"spec","publisher":"retailer","name":"Midwest Gun Works, Guntec AR-15 Mil-Spec Buffer Tube Set (MILTUBESET)","url":"https://www.midwestgunworks.com/page/mgwi/prod/miltubeset","retrieved":"2026-10-21","via":"harvest"},"note":"The set's buffer as this seller names it; its picture of the set (657de6718f20) has this buffer in it. Redcon1 Tactical's \"Buffer Weight: 3.0 oz (Carbine)\" and The Country Shed's \"3 oz CAR Buffer\" are said of the set's buffer too (their pictures have Guntec's stainless buffer, guntec-ar15-stainless-carbine-buffer)."}],"adopt":{"from":"guntec","reason":"The maker's own figure, on its page of this buffer; Midwest Gun Works' name for the buffer in the set agrees."}},"length":{"label":"Length (the head's front face to the bumper's end)","kind":"length","measurements":[{"id":"layout","value":3.42,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/guntec-ar15-carbine-buffer 53eee351ef23 (The Country Shed's copy of Guntec's own layout picture of the red set, MILTUBESET-RED, 600 px: the tube, end plate, castle nut, buffer and spring laid out on white and photographed square on from above; its buffer has this one's white bumper and flanged head, in a black body: taken for this buffer in an earlier finish)","scaleRef":"the set's tube lying beside it in the same plane, 278 px for its 7.25 in (guntec-ar15-mil-spec-buffer-tube-gen-2.tube_length): 38.3 px/in; its body's 55 px for 1.448 in overall height and its thread's 44 px for 1.148 in give 38.0 and 38.3","method":"the buffer's silhouette on a 4x enlargement (.cache/guntec-set/guntec-ar15-carbine-buffer/crop_layout4.png), the white bumper's tip to the head's face, 132 px; its head reads 36.5 px across, 0.95 in, where the standard's is 0.98. The ± is 3 px at each end of a small picture","via":"harvest"}},{"id":"carbuf-photo","value":3.39,"unit":"in","pm":0.07,"source":{"type":"photo","photo":"references/guntec-ar15-carbine-buffer af72b3d271e9 (Midwest Gun Works' picture of Guntec's carbine buffer sold alone, CARBUF.jpg, 1500 px: square on from the side, head to the left, on white)","scaleRef":"its own diameters as the standard's: the head (std.carbine_buffer.head_d 0.98) 350 px, the step the spring sits over (pilot_d 0.781) 283 px, the body (body_d 0.687) 240 px: 357, 362 and 349 px/in","method":"the silhouette's length along its axis, 1206 px, the head's face to the bumper's tip (.cache/guntec-set/guntec-ar15-carbine-buffer/sil.py): 3.38 in by the head, 3.33 by the step and 3.45 by the body; the ± spans the three. The picture is turned about 1 degree and shows a sliver of the head's face (15 px), which the ± covers","via":"harvest"}},{"id":"std","value":3.251,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.carbine_buffer.length}","via":"harvest"},"note":"The standard carbine buffer's, which a seller's \"Mil-Spec\" gives it (Midwest Gun Works: \"This Mil-Spec aluminum constructed buffer is manufactured by Guntec for the AR-15 carbine platform\")."}],"adopt":{"from":"layout","reason":"Two photographs of Guntec's buffer, one scaled by the tube lying beside it and one by the buffer's own standard diameters, agree within their ± (3.42 and 3.39) and are 0.14 to 0.17 in longer than the standard's 3.251, more than either's ±. A seller's \"Mil-Spec\" is a word for the buffer, not a length; no page states one. The tube-scaled reading is adopted: it rests on nothing of the buffer's own."}},"body_length":{"label":"Its body's length (the head's front face to the bumper's seat)","kind":"length","measurements":[{"id":"derived","value":3.02,"unit":"in","pm":0.08,"source":{"type":"derived","expr":"{.length} - {std.carbine_buffer.bumper_exposed}","via":"harvest"}}],"note":"What the model's body is drawn to: the length less the standard bumper standing out of it. The CARBUF photo's bumper stands 148 px out of its body, 0.42 in at the body's scale, where the standard's is 0.40."},"od":{"label":"Diameter (its head, which runs in the extension's bore)","kind":"length","measurements":[{"id":"std","value":0.98,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.carbine_buffer.head_d}","via":"harvest"},"note":"The standard's, by a seller's \"Mil-Spec\". The layout picture (53eee351ef23) reads its head 0.95 in across at the tube's scale, within that small picture's ± of 3 px (0.08 in)."}]}}},{"subject":"guntec-ar15-castle-nut","title":"Guntec USA Castle Nut (of its AR-15 Mil-Spec Buffer Tube Set)","dimensions":{"od":{"label":"Outside diameter","kind":"length","measurements":[{"id":"ctd-thread","value":1.355,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/guntec-ar15-castle-nut bd27a5b91cde (Cheaper Than Dirt: Guntec's CASTLE nut alone, 1000 x 1000; lying on its front face, seen from above at an angle)","scaleRef":"its own thread: four grooves on the far inner wall at rows 234, 271, 308 and 345, 37 px apart, a 1/16 in pitch along the axis seen at the cosine 0.854: 693 px/in there","method":"its width across the picture, 958 px (rows 440 to 520), at that scale is 1.38; the far wall stands about as far behind the nut's middle as its radius, which at the lens's distance (the near rim reads larger than the far by the ellipse's halves) puts the middle's scale about 2% larger","via":"harvest"}},{"id":"model","value":1.363,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"one cylinder, r 0.6815 (.cache/buffer/std/faces.Buffer_Tube_Nut.txt)","via":"user"},"note":"A mil-spec nut as the reference model has it, another than Guntec's (it is 0.3765 thick: thickness)."}],"adopt":{"from":"ctd-thread","reason":"Its own thread as the scale, on the one large photograph of this nut; the reference model's mil-spec nut is 0.008 larger, inside the ±. (Guntec's own pictures of its sets, read for this figure until 2026-10-20, show the heavy duty nut.)"}},"thickness":{"label":"Thickness","kind":"length","measurements":[{"id":"ctd-thread","value":0.294,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/guntec-ar15-castle-nut bd27a5b91cde (Cheaper Than Dirt: Guntec's CASTLE nut alone, 1000 x 1000; lying on its front face, seen from above at an angle)","scaleRef":"its own thread on the far inner wall: grooves 37 px apart down the picture, each a 1/16 in pitch along the axis; a ratio on one wall at one depth, needing no other scale","method":"the far inner wall from the rear face's inner edge (row 196, the end of the rear face's 30 px band below its outer edge at 166) to where the bore opens on its front face (row 371): 175 px, 4.7 pitches. Counted on columns 420 to 580: the grooves at 231 to 234, 268 to 272, 306 to 309, 342 to 346 on each","via":"harvest"}},{"id":"ctd-side","value":0.276,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/guntec-ar15-castle-nut bd27a5b91cde (Cheaper Than Dirt: Guntec's CASTLE nut alone, 1000 x 1000)","scaleRef":"its outside diameter (.od) across the picture, 958 px; the lens's angle from the rear face's ellipse (outer edge at rows 166 and 664 on column 500: 498 px over 958, sine 0.520, cosine 0.854)","method":"the near side, column 500: from the rear face's outer edge (row 664, where its lit band rounds over into the side) to the silhouette's bottom (row 831, the front face's outer edge): 167 px, over the cosine, at 708.6 px/in","via":"harvest"},"note":"On the near side, where a lens close by draws larger than at the middle: if anything this reads long, and it reads 0.018 under the thread's count."},{"id":"redcon1","value":0.282,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/guntec-ar15-end-plate 59e737ecf3a6 (Redcon1 Tactical: Guntec's chrome set laid out, 1215 x 1035; this nut on its front face beside the set's tube, seen from above. The same photograph of the nut as its red set's picture, 2ab5455bdba9, at 1.5 times the size)","scaleRef":"the nut's width across the picture, 196.5 px (rows 710 to 750), as .od: 145.3 px/in; the angle from its rear face's ellipse (outer edge at rows 652.5 and 796 on column 393: 143.5 over 196.5, sine 0.730, cosine 0.683)","method":"the near side, column 393: the rear face's inner edge at row 780.5, its band 9 px (the wall, (od - thread) / 2, at the sine), the silhouette's bottom at 817.5: 28 px over the cosine. Its far inner wall agrees: 29.5 px from the rear face's band to where the bore opens (row 691), grooves 6.5 px apart, 4.5 pitches","via":"harvest"}},{"id":"model","value":0.3765,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"its front face to its rear face, planes y 0 and y 0.3765","via":"user"},"note":"A mil-spec nut as the reference model has it: another nut, six turns of thread long where Guntec's photo shows four grooves and a part."}],"adopt":{"from":"ctd-thread","reason":"Its own thread as the scale, on one wall at one depth. Its near side read through its diameter agrees within the ±, and so does Redcon1's larger picture of it beside Guntec's chrome set (its near side 0.282, its thread 4.5 pitches); the reference model's mil-spec nut is 0.08 thicker, a conflict said: Guntec's CASTLE is a thinner nut (its heavy duty nut is 0.375)."}},"notches":{"label":"Notches on its rear face","kind":"count","measurements":[{"id":"ctd","value":4,"unit":"count","source":{"type":"photo","photo":"references/guntec-ar15-castle-nut bd27a5b91cde (Cheaper Than Dirt: Guntec's CASTLE nut alone, 1000 x 1000; the rear face whole, seen from above)","scaleRef":"none (a count)","method":"the gaps in the rear face's rim, counted all the way round the ellipse: at about 30, 128, 209 and 301 degrees round the axis from the side nearest the lens (from where each gap's middle stands across the ellipse), 98, 81, 92 and 89 apart","via":"harvest"}},{"id":"redcon1","value":4,"unit":"count","source":{"type":"photo","photo":"references/guntec-ar15-castle-nut 2ab5455bdba9 (Redcon1 Tactical: Guntec's red set laid out; this nut beside the set's tube, its rear face whole)","scaleRef":"none (a count)","method":"the gaps in the rim, counted round the ellipse","via":"harvest"}}],"adopt":{"from":"ctd","reason":"Counted on the larger photo of the nut alone; the nut beside the set's tube in Redcon1's picture has as many."}},"notch_width":{"label":"Castle nut wrench notch width","kind":"length","measurements":[{"id":"ctd","value":0.162,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/guntec-ar15-castle-nut bd27a5b91cde (Cheaper Than Dirt: Guntec's CASTLE nut alone, 1000 x 1000)","scaleRef":"its outside diameter (.od) across the picture, 958 px: 707 px/in","method":"the near notch at 30 degrees round from the lens's side: the backdrop seen through it from column 690 to 782 (rows 640 to 650), 92 px. A slot through a wall seen at that angle shows its width times the cosine less the wall's depth times the sine: (0.130 x 0.866) + 0.085 x 0.577","via":"harvest"},"note":"Read at first (2026-10-20) as 0.15, the gap over the cosine alone."}]},"notch_depth":{"label":"Castle nut wrench notch depth (into the rear face)","kind":"length","measurements":[{"id":"ctd","value":0.115,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/guntec-ar15-castle-nut bd27a5b91cde (Cheaper Than Dirt: Guntec's CASTLE nut alone, 1000 x 1000)","scaleRef":"708.6 px/in across; along the axis times the cosine 0.854","method":"the near notch at column 740: the rear face's outer edge there (row 630.6, on its ellipse) to the notch's floor's outer edge (row 700): 69.4 px","via":"harvest"},"note":"The floor is 0.42 of the way down the near side at that column, as the thickness and this depth make it (0.115 of 0.276 read on that side)."}]},"hole_d":{"label":"Castle nut, the radial hole in its side: diameter","kind":"length","measurements":[{"id":"ctd","value":0.15,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/guntec-ar15-castle-nut bd27a5b91cde (Cheaper Than Dirt: Guntec's CASTLE nut alone, 1000 x 1000)","scaleRef":"708.6 px/in across","method":"its dark disc across the picture, columns 333 to 436 (luminance under 40), 103 px, over the cosine of its 14 degrees round from the lens's side (0.970)","via":"harvest"}}],"note":"One hole, through its side between two notches: on Cheaper Than Dirt's photo of the CASTLE nut, and on the nut in Redcon1's picture of Guntec's red set and ABC Sportz's of its gold set (references/guntec-ar15-end-plate 0b3672e01b07). No page says what it is for."},"hole_from_front":{"label":"Castle nut, the radial hole's centre from its front face","kind":"length","measurements":[{"id":"ctd","value":0.133,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/guntec-ar15-castle-nut bd27a5b91cde (Cheaper Than Dirt: Guntec's CASTLE nut alone, 1000 x 1000)","scaleRef":"708.6 px/in across; along the axis times the cosine 0.854","method":"the hole's middle (row 743) above the silhouette's bottom at its column (the front face's outer edge, row 823.6 on its ellipse): 80.6 px","via":"harvest"},"note":"About the middle of its thickness (0.294). Redcon1's small photo has it lower, nearer the front face, by eye."}]},"hole_round":{"label":"Castle nut, the radial hole: how far round the axis from the nearest wrench notch","kind":"angle","measurements":[{"id":"ctd","value":44.5,"unit":"deg","pm":5,"source":{"type":"photo","photo":"references/guntec-ar15-castle-nut bd27a5b91cde (Cheaper Than Dirt: Guntec's CASTLE nut alone, 1000 x 1000)","scaleRef":"none (angles round the ellipse)","method":"the hole's middle at -14 degrees round the axis from the lens's side, the two notches either side at 30 and -59: 44 and 45 degrees from each","via":"harvest"}}]},"hole_depth":{"label":"Castle nut, the radial hole: how deep","kind":"length","measurements":[{"id":"assumed","value":0.085,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows the hole's bottom; drawn through the wall to the thread, the wall's thickness between its outside and the thread's crest ((1.352 - 1.1813) / 2).","via":"harvest"}}]},"edge_break":{"label":"Castle nut, the break on its edges","kind":"length","measurements":[{"id":"assumed","value":0.012,"unit":"in","pm":0.006,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: Cheaper Than Dirt's photo shows the rear face's outer edge rounded over by a few pixels (rows 656 to 672 at column 500), about 0.02 in, which a 0.012 break with two segments draws.","via":"harvest"}}]},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"metal","value":0.428,"unit":"oz","pm":0.04,"source":{"type":"derived","expr":"(0.785398163 * ({.od} * {.od} - {std.receiver_extension.thread_major_d} * {std.receiver_extension.thread_major_d}) * {.thickness} - {.notches} * {.notch_width} * {.notch_depth} * ({.od} - {std.receiver_extension.thread_major_d}) / 2 - 0.785398163 * {.hole_d} * {.hole_d} * ({.od} - {std.receiver_extension.thread_major_d}) / 2) * {std.density.steel}","via":"harvest"}}],"note":"No page states its weight. Worked out from its sizes: a steel ring of its outside diameter and thickness round the extension's thread, less its four wrench notches and its radial hole. Steel by Cheaper Than Dirt's page of the CASTLE nut (Guntec's list as the seller carries it: \"Steel Matte Black\")."}}},{"subject":"guntec-ar15-chrome-silicon-buffer-spring","title":"Guntec USA Upgraded Chrome Silicon Spring","dimensions":{"free_length":{"label":"Free length","kind":"length","measurements":[{"id":"redcon1","value":11,"unit":"in","pm":0.5,"stated":"Spring Length: 11\" (Carbine)","source":{"type":"spec","publisher":"retailer","name":"Redcon1 Tactical, Guntec USA AR-15 Mil-Spec Buffer Tube Kit - Anodized Red (MILTUBESET-RED)","url":"https://redcon1tactical.com/guntec-usa-ar-15-mil-spec-buffer-tube-kit-anodized-red.html","retrieved":"2026-10-18","via":"harvest"},"note":"The seller's spec table; its other table has \"Buffer Spring Length Carbine Length\"."},{"id":"layout","value":12.1,"unit":"in","pm":0.1,"source":{"type":"photo","photo":"references/guntec-ar15-chrome-silicon-buffer-spring 53eee351ef23 (The Country Shed's copy of Guntec's own layout picture of the red set, MILTUBESET-RED, 600 px: the set laid out on white, square on from above; Guntec's page has the picture as MILTUBESET-RED.jpg, uploaded 2019-08)","scaleRef":"the set's tube lying beside it, 278 px for its 7.25 in (guntec-ar15-mil-spec-buffer-tube-gen-2.tube_length): 38.3 px/in; its body's height and its thread's diameter give 38.0 and 38.3","method":"the spring's silhouette end to end along its axis (turned 0.7 degree), 464 to 465 px at three thresholds of darkness (.cache/guntec-set/guntec-ar15-chrome-silicon-buffer-spring/od.py)","via":"harvest"}}],"adopt":{"from":"redcon1","reason":"A seller's figure for the set as sold; Guntec's own picture of the spring, laid out beside the tube that scales it, is 1.1 in longer, more than the two ±. The picture is from 2019 (its file's upload on Guntec's page) and may be an earlier spring; the free length isn't drawn (the spring is drawn as installed)."}},"coils":{"label":"Total coils","kind":"count","measurements":[{"id":"layout","value":39,"unit":"count","pm":1,"source":{"type":"photo","photo":"references/guntec-ar15-chrome-silicon-buffer-spring 53eee351ef23 (Guntec's layout picture of the red set, as above)","scaleRef":"none: a count","method":"the crests of the spring's outline along each side of its axis (layout.py): 41 on the top edge with two pairs 6 px apart (a closed end coil's two strands, and one doubled crest) and the rest 11 to 13 px apart, 39 coils; 40 on the bottom edge with the last 7 px from its neighbour, 39. Both ends closed, as an enlargement shows (a2.jpg, b2.jpg). Redcon1's oblique picture of the whole spring (eabe3e83f28b) gave crests 8 to 48 px apart, the far side's coils showing between the near side's: not used","via":"harvest"}}]},"wire_d":{"label":"Wire diameter","kind":"length","measurements":[{"id":"std","value":0.072,"unit":"in","pm":0.001,"source":{"type":"derived","expr":"{std.carbine_action_spring.wire_d}","via":"harvest"},"note":"AN APPROXIMATION: the Army's drawing's wire for the rifle's action spring, the standard carbine spring's. No page states this one's, and at the layout picture's 38 px to the inch the wire is under 3 px."}]},"od":{"label":"Outside diameter of its coils","kind":"length","measurements":[{"id":"std","value":0.94,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{std.carbine_action_spring.od}","via":"harvest"},"note":"The standard's: it goes over the buffer's step and inside the tube's 1.000 bore, as every carbine spring does."},{"id":"layout","value":0.94,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/guntec-ar15-chrome-silicon-buffer-spring 53eee351ef23 (Guntec's layout picture of the red set, as above)","scaleRef":"the tube beside it: 38.3 px/in","method":"the outline's crest to crest across its axis, the median over each pitch's span: 37.1 px at the lightest threshold of darkness and 35.1 at the darkest (od.py), 0.97 to 0.92 in; the ± is the threshold's","via":"harvest"}}],"adopt":{"from":"std","reason":"The standard's figure, which Guntec's picture of the spring bears out within its ±."}},"installed_length":{"label":"Its length as installed (a carbine buffer's seat to the set's tube's rear wall, bolt forward)","kind":"length","measurements":[{"id":"room","value":6.972,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{guntec-ar15-mil-spec-buffer-tube-gen-2.tube_front_behind_pin} + {guntec-ar15-mil-spec-buffer-tube-gen-2.tube_length} - {std.receiver_extension.carbine_rear_wall} + {std.ar15.upper_rear_face_x} - {std.carbine_buffer.head_thickness}","via":"harvest"}}],"note":"What the spring is drawn at, in the set's own tube: from the rear face of a carbine buffer's head, whose front face rests at the upper receiver's rear face (the carrier's rear end, bolt forward), back to the rear wall inside Guntec's tube."},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"wire","value":1.98,"unit":"oz","pm":0.13,"source":{"type":"derived","expr":"3.14159265 * ({.od} - {.wire_d}) * {.coils} * 0.785398163 * {.wire_d} * {.wire_d} * {std.density.steel}","via":"harvest"}}],"note":"No maker's or seller's figure: no page states one. Worked out from its wire: the wire's length round its coils times its section times what steel weighs (chrome silicon spring wire is a steel). A derived figure, for the build's total; the ± is the coil count's, the wire's and the density's together."}}},{"subject":"guntec-ar15-end-plate","title":"Guntec USA End Plate (of its AR-15 Mil-Spec Buffer Tube Set)","dimensions":{"thickness":{"label":"Thickness","kind":"length","measurements":[{"id":"model","value":0.124,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the plate's two faces, planes y 0 and y 0.1240 (.cache/buffer/std/faces.Buffer_Tube_Rotation_Lock.txt)","via":"user"},"note":"A mil-spec plate as the reference model has it: Guntec's plate has that plate's outline on three photos (top_above_axis, bottom_below_axis, boss_width)."},{"id":"redcon1","value":0.11,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/guntec-ar15-end-plate 2ab5455bdba9 (Redcon1 Tactical: Guntec's red set laid out, 810 x 690; the plate lying flat, seen from above)","scaleRef":"the hole's width taken as a mil-spec plate's (std.receiver_extension.end_plate_hole_d), 94.7 px/in across; the plate's tilt from its round hole's aspect, 0.73 (the hole's own 0.655 with the wall's thickness seen at its far side added back)","method":"the lobe's lit edge at its bottom, rows 641 to 648 at column 409: 7 px, over the cosine of the tilt (0.68)","via":"harvest"},"note":"Two or three pixels: a check, not a size."}],"adopt":{"from":"model","reason":"No page states it; Guntec's plate has the reference model's outline on three photos, and the one photo that shows its edge agrees within its ±."},"note":"A stamped plate: no page states its thickness."},"top_above_axis":{"label":"End plate top above the tube axis (its ring's radius)","kind":"length","measurements":[{"id":"model","value":0.6817,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the ring's outer cylinder, r 0.6817 (#899)","via":"user"}},{"id":"guntec-clear","value":0.68,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/guntec-ar15-mil-spec-buffer-tube-gen-2 e0853c782418 (Guntec: its clear set assembled, MILTUBESET-CLEAR, 900 px; from the user's saved page of the clear tube, 2026-10-19)","scaleRef":"the tube's own outside diameter just behind the nut, where it is the tube alone, taken as std.receiver_extension.milspec_od (1.148): 84.3 px, 73.4 px/in across the axis","method":"the silhouette's reach above the tube's axis where the plate stands (along the axis 80 to 104 px from the reference column), in the frame of the tube's top and bottom edges; the median of those columns","via":"harvest"},"note":"Read across the axis, which a cylinder's silhouette shows whatever the lens's yaw; a flat plate's height reads short by the cosine of how far above or below it the lens stood."},{"id":"guntec-purple","value":0.667,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/guntec-ar15-mil-spec-buffer-tube-gen-2 0ab407ab3350 (Guntec: its purple set assembled, MILTUBESET-PURPLE_Rev, 900 px; from the user's saved page of the purple tube, 2026-10-19)","scaleRef":"the tube's own outside diameter just behind the nut, taken as std.receiver_extension.milspec_od (1.148): 82.5 px, 71.8 px/in across the axis","method":"as the clear set's: the median reach above the axis along the plate","via":"harvest"}},{"id":"guntec","value":0.702,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/guntec-ar15-end-plate 9c7a4e9ee983 (Guntec: ENDPLATE_2048, its own picture of the plate face on, 2048 px, from its page as the user saved it, 2026-10-20)","scaleRef":"down: the picture isn't square on (the hole's ellipse is 0.928 as tall as wide, its turn under 2 degrees): the mean of the hole's own (506 px for its radius) and the ring's (601 px for the 0.69 its width gives), 861 px/in, the plate's edge seen at the tilt shortening the one and lengthening the other; heights from the two ellipses' centres, row 745","method":"the outline's top (row 140) above the hole's centre","via":"user"},"note":"Its width across, 2 x 632 px of the ring's ellipse, is 1.379 at 916.6 px/in: the ring's radius 0.690."}],"adopt":{"from":"model","reason":"The reference model's ring; Guntec's two photos read it within their ±."}},"bottom_below_axis":{"label":"End plate lobe bottom below the tube axis","kind":"length","measurements":[{"id":"model","value":1.3788,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the lobe's round end, r 0.4266 about a centre 0.9522 below the axis","via":"user"}},{"id":"redcon1","value":1.384,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/guntec-ar15-end-plate 2ab5455bdba9 (Redcon1 Tactical: Guntec's red set laid out, 810 x 690; the plate lying flat, seen from above)","scaleRef":"a ratio, needing no scale: the lobe's bottom is 2.03 times as far below the hole's centre as the ring's top is above it, both read down the picture (they are foreshortened alike); times the ring's radius (.top_above_axis)","method":"the plate's outline (luminance < 150, largest piece) and its hole's ellipse fitted away from the key: top 50.1 px above the hole's centre, bottom 101.9 px below it","via":"harvest"}},{"id":"guntec-clear","value":1.338,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/guntec-ar15-mil-spec-buffer-tube-gen-2 e0853c782418 (Guntec: its clear set assembled, MILTUBESET-CLEAR, 900 px)","scaleRef":"the tube's own outside diameter, as for top_above_axis (73.4 px/in)","method":"the silhouette's greatest reach below the tube's axis where the plate's lobe hangs","via":"harvest"},"note":"Read across the axis: short by the cosine of how far above or below the plate the lens stood. The same photo's top over this bottom is 1.97."},{"id":"guntec-purple","value":1.346,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/guntec-ar15-mil-spec-buffer-tube-gen-2 0ab407ab3350 (Guntec: its purple set assembled, MILTUBESET-PURPLE_Rev, 900 px)","scaleRef":"the tube's own outside diameter (71.8 px/in)","method":"as the clear set's","via":"harvest"},"note":"This photo's bottom over its own top is 2.02, the reference model's ratio (1.3788 over 0.6817): both read short alike, as a lens 12 degrees above or below the plate would read them."},{"id":"guntec","value":1.399,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/guntec-ar15-end-plate 9c7a4e9ee983 (Guntec: ENDPLATE_2048, its own picture of the plate face on, 2048 px, from its page as the user saved it, 2026-10-20)","scaleRef":"down: the picture isn't square on (the hole's ellipse is 0.928 as tall as wide, its turn under 2 degrees): the mean of the hole's own (506 px for its radius) and the ring's (601 px for the 0.69 its width gives), 861 px/in, the plate's edge seen at the tilt shortening the one and lengthening the other; heights from the two ellipses' centres, row 745","method":"the outline's bottom (row 1949) below the hole's centre","via":"user"},"note":"The edge seen at the tilt is in it, on one side of the plate or the other: a few hundredths."}],"adopt":{"from":"model","reason":"The reference model's lobe. Redcon1's face-on photo puts the bottom at its ratio to the ring (1.384); Guntec's own two photos read it 0.03 to 0.04 short across the tube's axis, and the purple one its top short alike, which is the lens standing off the plate's plane, not a shorter lobe. Kept as read: the clear photo's is just outside its ±, a conflict said."},"note":"The lobe covers the takedown pin's detent spring."},"height":{"label":"End plate height (its top to its lobe's bottom)","kind":"length","measurements":[{"id":"derived","value":2.0605,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{.top_above_axis} + {.bottom_below_axis}","via":"harvest"}}]},"lobe_radius":{"label":"End plate, the radius of its lobe's round end","kind":"length","measurements":[{"id":"model","value":0.4266,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the lobe's end cylinder, r 0.4266 (#973)","via":"user"},"note":"Redcon1's photo of Guntec's plate has the lobe's widths at three depths (as fractions of its height) 0.01 to 0.03 in over this outline's, after the outline's 0.04 of shadow is taken off: the lower rows, nearer the lens, read larger."}]},"lobe_centre_below_axis":{"label":"End plate, its lobe's round end's centre below the tube axis","kind":"length","measurements":[{"id":"model","value":0.9522,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the lobe's end cylinder's axis (#973)","via":"user"}}]},"hole_d":{"label":"End plate, its hole for the extension's thread","kind":"length","measurements":[{"id":"std","value":1.1902,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{std.receiver_extension.end_plate_hole_d}","via":"harvest"},"note":"A mil-spec plate's hole, as the reference model has it: Redcon1's photo is scaled by it (the ring's width then reads 1.405 with 0.04 of the outline's shadow in it, the model's 1.363 and that shadow)."}]},"key_width":{"label":"End plate, its key's width","kind":"length","measurements":[{"id":"model","value":0.125,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the key's side planes, x ±0.0625 (#1108, #1162)","via":"user"},"note":"The extension's slot it rides in is as wide (std.receiver_extension.key_slot_width)."},{"id":"guntec","value":0.114,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/guntec-ar15-end-plate 9c7a4e9ee983 (Guntec: ENDPLATE_2048, its own picture of the plate face on, 2048 px, from its page as the user saved it, 2026-10-20)","scaleRef":"across: the hole's width taken as a mil-spec plate's (std.receiver_extension.end_plate_hole_d), its ellipse's across semi-axis 545.5 px: 916.6 px/in","method":"the key across, rows 1230 to 1250 (luminance under 150): 100 to 108 px","via":"user"}}],"adopt":{"from":"model","reason":"The reference model's key, as wide as the extension's slot it rides in; Guntec's picture reads it within its ± (its edges' rounding narrows the silhouette)."}},"key_tip_below_axis":{"label":"End plate, its key's tip below the tube axis","kind":"length","measurements":[{"id":"model","value":0.5619,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the key's tip plane, z 0.5619 (#1135)","via":"user"},"note":"0.012 below the extension's slot floor (std.receiver_extension.key_slot_floor, 0.55): the key stands clear of it."},{"id":"guntec","value":0.541,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/guntec-ar15-end-plate 9c7a4e9ee983 (Guntec: ENDPLATE_2048, its own picture of the plate face on, 2048 px, from its page as the user saved it, 2026-10-20)","scaleRef":"down: the picture isn't square on (the hole's ellipse is 0.928 as tall as wide, its turn under 2 degrees): the mean of the hole's own (506 px for its radius) and the ring's (601 px for the 0.69 its width gives), 861 px/in, the plate's edge seen at the tilt shortening the one and lengthening the other; heights from the two ellipses' centres, row 745","method":"the key's tip (row 1211) below the hole's centre","via":"user"}}],"adopt":{"from":"model","reason":"The reference model's; Guntec's picture reads it within its ±."}},"relief_bottom_below_axis":{"label":"End plate, the V either side of its key: its floor below the tube axis","kind":"length","measurements":[{"id":"model","value":0.6575,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the two sloped planes' lower ends, z 0.6575 (#1054, #1216), where 0.031 in rounds turn them into the key's sides","via":"user"}},{"id":"guntec","value":0.651,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/guntec-ar15-end-plate 9c7a4e9ee983 (Guntec: ENDPLATE_2048, its own picture of the plate face on, 2048 px, from its page as the user saved it, 2026-10-20)","scaleRef":"down: the picture isn't square on (the hole's ellipse is 0.928 as tall as wide, its turn under 2 degrees): the mean of the hole's own (506 px for its radius) and the ring's (601 px for the 0.69 its width gives), 861 px/in, the plate's edge seen at the tilt shortening the one and lengthening the other; heights from the two ellipses' centres, row 745","method":"the V's lowest either side of the key (row 1305) below the hole's centre","via":"user"}}],"adopt":{"from":"model","reason":"The reference model's; Guntec's picture reads it within its ±."}},"relief_floor_half_width":{"label":"End plate, the V either side of its key: where its sloped sides end, out from the middle","kind":"length","measurements":[{"id":"model","value":0.1119,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the sloped planes' inner ends, x ±0.1119 (#1054, #1216)","via":"user"}}]},"relief_top_half_width":{"label":"End plate, the V either side of its key: where it leaves the hole's circle, out from the middle","kind":"length","measurements":[{"id":"model","value":0.354,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the hole's cylinder ends at x ±0.3540, z 0.4784 (#1007), where the sloped planes begin","via":"user"}}]},"relief_fillet_r":{"label":"End plate, the round at the bottom of the V either side of its key, where it turns into the key's side","kind":"length","measurements":[{"id":"model","value":0.031,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"two cylinders r 0.031 at x ±0.0935, z 0.6326 (#1081, #1189)","via":"user"}}]},"edge_break":{"label":"End plate, the break on its edges","kind":"length","measurements":[{"id":"assumed","value":0.012,"unit":"in","pm":0.006,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows its edges in profile; the reference model's are sharp. A stamped plate's edges are broken a little, and a sharp edge reads as a line of light in the app.","via":"harvest"}}]},"boss_width":{"label":"End plate, its boss side to side","kind":"length","measurements":[{"id":"model","value":0.496,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"an obround: two r 0.1875 ends at x ±0.0605","via":"user"}},{"id":"redcon1","value":0.497,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/guntec-ar15-end-plate 2ab5455bdba9 (Redcon1 Tactical: Guntec's red set laid out, 810 x 690; the plate lying flat, seen from above)","scaleRef":"the hole's width taken as a mil-spec plate's (std.receiver_extension.end_plate_hole_d): 94.7 px/in across the picture, where the plate isn't foreshortened","method":"row 612 across the obround: its rim's two dark lines at columns 390 and 437, 47 px","via":"harvest"},"note":"Redcon1's chrome set picture (references/guntec-ar15-end-plate 59e737ecf3a6, 1215 px) has the same photograph of the plate at 1.5 times the size: its obround reads 0.492 there (row 920, columns 586 and 656, at 142.2 px/in by the hole). Not a second plate."},{"id":"guntec","value":0.504,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/guntec-ar15-end-plate 9c7a4e9ee983 (Guntec: ENDPLATE_2048, its own picture of the plate face on, 2048 px, from its page as the user saved it, 2026-10-20)","scaleRef":"across: the hole's width taken as a mil-spec plate's (std.receiver_extension.end_plate_hole_d), its ellipse's across semi-axis 545.5 px: 916.6 px/in","method":"row 1584 across the boss: the dark lines of its edges at columns 825 and 1287, 462 px","via":"user"}}],"adopt":{"from":"model","reason":"Guntec's own obround reads the reference model's width to a thousandth."}},"boss_height":{"label":"End plate, its boss top to bottom","kind":"length","measurements":[{"id":"model","value":0.375,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the obround's two ends' diameter","via":"user"}},{"id":"redcon1","value":0.376,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/guntec-ar15-end-plate 2ab5455bdba9 (Redcon1 Tactical: Guntec's red set laid out, 810 x 690; the plate lying flat, seen from above)","scaleRef":"94.7 px/in across, times the plate's tilt down the picture (0.73, as for thickness)","method":"column 409 down the obround: its rim's dark lines at rows 603 and 629, 26 px","via":"harvest"}},{"id":"guntec","value":0.409,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/guntec-ar15-end-plate 9c7a4e9ee983 (Guntec: ENDPLATE_2048, its own picture of the plate face on, 2048 px, from its page as the user saved it, 2026-10-20)","scaleRef":"down: the picture isn't square on (the hole's ellipse is 0.928 as tall as wide, its turn under 2 degrees): the mean of the hole's own (506 px for its radius) and the ring's (601 px for the 0.69 its width gives), 861 px/in, the plate's edge seen at the tilt shortening the one and lengthening the other; heights from the two ellipses' centres, row 745","method":"the boss's top and bottom edges, rows 1408 and 1760","via":"user"},"note":"Its side, 0.065 proud, shows at the tilt and is in this reading."}],"adopt":{"from":"model","reason":"Guntec's own obround agrees within its ±."}},"boss_below_axis":{"label":"End plate, its boss's middle below the tube's axis","kind":"length","measurements":[{"id":"model","value":0.9974,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the obround's centre","via":"user"}},{"id":"redcon1","value":1,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/guntec-ar15-end-plate 2ab5455bdba9 (Redcon1 Tactical: Guntec's red set laid out, 810 x 690; the plate lying flat, seen from above)","scaleRef":"as for boss_height","method":"the obround's middle (row 616) below the hole's fitted centre (row 546.6): 69.4 px","via":"harvest"}},{"id":"guntec","value":0.974,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/guntec-ar15-end-plate 9c7a4e9ee983 (Guntec: ENDPLATE_2048, its own picture of the plate face on, 2048 px, from its page as the user saved it, 2026-10-20)","scaleRef":"down: the picture isn't square on (the hole's ellipse is 0.928 as tall as wide, its turn under 2 degrees): the mean of the hole's own (506 px for its radius) and the ring's (601 px for the 0.69 its width gives), 861 px/in, the plate's edge seen at the tilt shortening the one and lengthening the other; heights from the two ellipses' centres, row 745","method":"the boss's middle (row 1584) below the hole's centre","via":"user"}}],"adopt":{"from":"model","reason":"Guntec's own obround agrees within its ±."}},"boss_proud":{"label":"End plate, how far its boss stands out of its front face","kind":"length","measurements":[{"id":"model","value":0.0645,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the boss's face, plane y 0.1885 of a plate 0.1240 thick","via":"user"},"note":"No photo on file shows Guntec's boss in profile."}]},"dimple_depth":{"label":"End plate, the dimple in its rear face behind the boss","kind":"length","measurements":[{"id":"model","value":0.063,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"plane y 0.0630; the dimple is the boss's outline 0.005 larger all round","via":"user"},"note":"No photo on file shows Guntec's dimple in profile."}]},"dimple_grow":{"label":"End plate, how much larger all round its dimple is than its boss","kind":"length","measurements":[{"id":"model","value":0.005,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the dimple's ends r 0.1925 against the boss's r 0.1875 (#1433, #1223)","via":"user"}}]},"side_angle":{"label":"End plate, its lobe's straight sides: how far each leans in from upright","kind":"angle","measurements":[{"id":"model","value":13.5,"unit":"deg","pm":0.05,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the side planes' normals (#946, #1000: 0.972, 0.233), whose lean is atan(0.233 / 0.972)","via":"user"}}],"note":"Each side is tangent to the lobe's round end and meets the ring's circle at a corner (it isn't tangent to the ring)."},"corner_angle":{"label":"End plate, where each straight side meets the ring: its angle below the level of the tube axis","kind":"angle","measurements":[{"id":"model","value":31.33,"unit":"deg","pm":0.05,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the side planes' upper ends, x ±0.5823, 0.3545 below the axis, on the ring's r 0.6817: atan(0.3545 / 0.5823)","via":"user"}}]},"face_area":{"label":"End plate, the area its outline holds (the hole not taken out)","kind":"length","measurements":[{"id":"derived","value":2.0875,"unit":"in","pm":0.004,"source":{"type":"derived","expr":"{.top_above_axis} * {.top_above_axis} * (180 + 2 * {.corner_angle}) * 3.14159265 / 360 + {.lobe_radius} * {.lobe_radius} * (180 - 2 * {.side_angle}) * 3.14159265 / 360 + {.lobe_radius} * {.lobe_centre_below_axis} * cos({.side_angle}) + {.top_above_axis} * cos({.corner_angle}) * ({.lobe_centre_below_axis} + {.lobe_radius} * sin({.side_angle})) - {.lobe_radius} * {.top_above_axis} * cos({.side_angle}) * sin({.corner_angle})","via":"harvest"}}],"note":"In square inches, held as a length's number: the ring's arc above the two corners and the lobe's round end below its tangent points, each as a sector about its own centre, and between them the four triangles from the axis to the corners, the tangent points and the lobe's centre."},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"metal","value":0.552,"unit":"oz","pm":0.02,"source":{"type":"derived","expr":"({.face_area} - 0.785398163 * {.hole_d} * {.hole_d}) * {.thickness} * {std.density.steel}","via":"harvest"}}],"note":"No page states its weight. Worked out from its sizes: its face's area less the hole for the extension's thread, through its thickness, as steel: Guntec, \"US Made Steel\", \"Material: Steel\" (its page as the user saved it, 2026-10-20). The key, the V beside it and the boss move a few thousandths of a cubic inch: inside the ±."}}},{"subject":"guntec-ar15-heavy-duty-castle-nut","title":"Guntec USA AR-15 Heavy Duty Wide Castle Nut For Car/M4 Buffer Tube (CASTLE-HD)","dimensions":{"od":{"label":"Outside diameter","kind":"length","measurements":[{"id":"guntec","value":1.3125,"unit":"in","pm":0.03125,"stated":"Product Width 1.3125\" Product Length 1.3125\"","source":{"type":"spec","publisher":"manufacturer","name":"Guntec USA, AR-15 Heavy Duty Wide Castle Nut For Car/M4 Buffer Tube, CASTLE-HD, its Additional Information; the page as the user saved it, references/guntec-ar15-heavy-duty-castle-nut/docs/ar15-heavy-duty-wide-castle-nut-for-car-m4-buffer-tube.saved-2026-10-20.html","url":"https://guntecusa.com/product/ar15-heavy-duty-wide-castle-nut-for-car-m4-buffer-tube/","retrieved":"2026-10-20","via":"user"},"note":"In sixteenths of an inch (1 5/16), as Guntec's sizes are on its pages (its tube's too): taken to its nearest sixteenth, a thirty-second either way. Width and length are the same figure: its diameter."},{"id":"guntec-purple","value":1.352,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/guntec-ar15-mil-spec-buffer-tube-gen-2 0ab407ab3350 (Guntec: its purple set assembled, MILTUBESET-PURPLE_Rev, 900 px; from the user's saved page of the purple tube, 2026-10-19)","scaleRef":"the tube's own outside diameter just behind the nut, where it is the tube alone, taken as std.receiver_extension.milspec_od (1.148): 82.5 px, 71.8 px/in across the axis","method":"the silhouette's width across the tube's axis where the nut stands (along the axis 64 to 76 px from the reference column), in the frame of the tube's top and bottom edges: 1.351 to 1.363, the median. A cylinder's silhouette is its diameter whatever the lens's yaw","via":"harvest"},"note":"The set's nut in Guntec's own picture of its set: a notch shows in its front face's edge, as on this one."},{"id":"guntec-clear","value":1.386,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/guntec-ar15-mil-spec-buffer-tube-gen-2 e0853c782418 (Guntec: its clear set assembled, MILTUBESET-CLEAR, 900 px)","scaleRef":"the tube's own outside diameter, as the purple's: 84.3 px, 73.4 px/in","method":"as the purple's: 1.376 to 1.398 along the nut, the median","via":"harvest"},"note":"The clear tube is a pale silhouette on white, its top edge a highlight: read at a tight threshold it may still lose a pixel at an edge, which makes the tube read thin and the nut large. A notch shows in the nut's front face's edge at its upper right (columns 474 to 478, rows 422 to 428)."}],"adopt":{"from":"guntec","reason":"Guntec's own figure for this nut. Its own pictures of the set's nut read it larger across the tube (the purple within the ±, the clear beyond it, a conflict said); its weight, 0.6 oz, sits between what 1.3125 and 1.35 make of it."}},"thickness":{"label":"Thickness","kind":"length","measurements":[{"id":"guntec","value":0.375,"unit":"in","pm":0.03125,"stated":"Product Height 0.375\"","source":{"type":"spec","publisher":"manufacturer","name":"Guntec USA, AR-15 Heavy Duty Wide Castle Nut For Car/M4 Buffer Tube, CASTLE-HD, its Additional Information; the page as the user saved it, references/guntec-ar15-heavy-duty-castle-nut/docs/ar15-heavy-duty-wide-castle-nut-for-car-m4-buffer-tube.saved-2026-10-20.html","url":"https://guntecusa.com/product/ar15-heavy-duty-wide-castle-nut-for-car-m4-buffer-tube/","retrieved":"2026-10-20","via":"user"},"note":"In sixteenths (6/16). Its height lying on its face: its thickness along the tube. \"Extra Wide For Stronger, More Durable Hold\" is this against Guntec's CASTLE nut, 0.29 in."},{"id":"photo-thread","value":0.405,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/guntec-ar15-heavy-duty-castle-nut bedbc28f3730 (Guntec's CASTLE-HD-1, 500 px; lying on its front face, seen from above)","scaleRef":"its own thread on the far inner wall: grooves 13.5 px apart down the picture (rows 128, 141, 154, 168, 181, 195.5 on column 260), each a 1/16 in pitch along the axis; a ratio on one wall at one depth","method":"the far inner wall from the rear face's inner edge (row 119, its 9.4 px band below the outer edge at 109.5) to where the bore opens on its front face (row 206.5): 87.5 px, 6.5 pitches","via":"harvest"},"note":"Its near side, read through its diameter (rows 311 to 390, over the cosine, at 280.4 px/in), is 0.337: a lens this close draws the two sides at scales a few percent apart, and the two readings lie either side of Guntec's figure."}],"adopt":{"from":"guntec","reason":"Guntec's own figure; its picture's far wall and near side read it 0.03 long and 0.04 short, either side of it."}},"notches":{"label":"Notches on its rear face","kind":"count","measurements":[{"id":"photo","value":4,"unit":"count","source":{"type":"photo","photo":"references/guntec-ar15-heavy-duty-castle-nut bedbc28f3730 (Guntec's CASTLE-HD-1, 500 px; the rear face whole, seen from above)","scaleRef":"none (a count)","method":"the gaps in the rear face's rim, counted all the way round the ellipse: front left and front right (45 degrees either side of the lens's side), back left and back right","via":"harvest"}}]},"notch_width":{"label":"Wrench notch width","kind":"length","measurements":[{"id":"photo","value":0.12,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/guntec-ar15-heavy-duty-castle-nut bedbc28f3730 (Guntec's CASTLE-HD-1, 500 px)","scaleRef":"its outside diameter (.od) across the picture: 280.4 px/in","method":"the front right notch at 45 degrees round: the backdrop seen through it 16 px across (rows 283 to 289, columns 366 to 381). A slot seen at that angle shows its width times the cosine less its wall's depth times the sine, the wall from the rear face's inner edge (1.146 in across the ellipse) to the outside: (0.057 x 0.707) + 0.083","via":"harvest"}}]},"notch_depth":{"label":"Wrench notch depth (into the rear face)","kind":"length","measurements":[{"id":"photo","value":0.078,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/guntec-ar15-heavy-duty-castle-nut bedbc28f3730 (Guntec's CASTLE-HD-1, 500 px)","scaleRef":"280.4 px/in across; along the axis times the cosine 0.837","method":"the front right notch at column 373: the rear face's outer edge there (row 281.8, on its ellipse) to its floor's outer edge (row 300, the floor's lit band from 293 below the backdrop seen through the notch): 18 px","via":"harvest"}}]},"staking_notches":{"label":"Notches in its front face's outer edge","kind":"count","measurements":[{"id":"model","value":3,"unit":"count","source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"three notches 120 degrees apart, counted in the face list (planes #20197, #20323 and their like)","via":"user"},"note":"Guntec's one picture shows the front face's near half: one notch there, at the front, midway between the two near wrench notches, and none at either side, as three at 120 degrees would have it and four at 90 wouldn't. The other two aren't in view: the count is the mil-spec nut's, which the picture allows."}]},"staking_notch_width":{"label":"Front face notch, width","kind":"length","measurements":[{"id":"photo","value":0.082,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/guntec-ar15-heavy-duty-castle-nut bedbc28f3730 (Guntec's CASTLE-HD-1, 500 px)","scaleRef":"280.4 px/in across","method":"the silhouette's bottom raised from row 390 to 383 between columns 224 and 247 (23 px), at the front, square to the lens","via":"harvest"}},{"id":"model","value":0.09,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"a notch's two side planes, ±0.0450","via":"user"}}],"adopt":{"from":"photo","reason":"Guntec's nut's own; the mil-spec nut's agrees within its ±."}},"staking_notch_depth":{"label":"Front face notch, depth into the front face","kind":"length","measurements":[{"id":"photo","value":0.03,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/guntec-ar15-heavy-duty-castle-nut bedbc28f3730 (Guntec's CASTLE-HD-1, 500 px)","scaleRef":"280.4 px/in; along the axis times the cosine 0.837","method":"the silhouette's bottom raised 7 px at the notch: its ceiling's outer edge","via":"harvest"}},{"id":"model","value":0.082,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"a notch's floor","via":"user"},"note":"The mil-spec nut's notch is deeper than Guntec's reads: another nut."}],"adopt":{"from":"photo","reason":"Guntec's nut's own, read where the notch makes the silhouette; the mil-spec nut's is another nut's, a conflict said."}},"staking_notch_radial":{"label":"Front face notch, how far in from the outside it is cut","kind":"length","measurements":[{"id":"model","value":0.075,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the notch's inner wall, a cylinder r 0.6065 of an outside r 0.6815","via":"user"},"note":"Guntec's picture says only that it is at least 0.046 in (the front face's edge further in would otherwise make the silhouette there). The model bores the nut at the thread's crests (0.066 in of wall here; the real nut's thread stands 0.036 further in), so drawn to 0.075 the notch opens into that bore: a shallow slot through the front face's edge."}]},"staking_round":{"label":"Front face notch: how far round the axis from the nearest wrench notch","kind":"angle","measurements":[{"id":"photo","value":45,"unit":"deg","pm":5,"source":{"type":"photo","photo":"references/guntec-ar15-heavy-duty-castle-nut bedbc28f3730 (Guntec's CASTLE-HD-1, 500 px)","scaleRef":"none (angles round the ellipse)","method":"the front notch's middle (column 235.5, 2.5 degrees round from the lens's side) and the two near wrench notches (columns 140 and 373, at -45 and +45)","via":"harvest"}}]},"edge_break":{"label":"The break on its edges","kind":"length","measurements":[{"id":"assumed","value":0.012,"unit":"in","pm":0.006,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: Guntec's picture is too small to show its edges' rounding (a pixel is 0.0036 in).","via":"harvest"}}]},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"guntec","value":0.6,"unit":"oz","stated":"Product Weight 0.6 oz","source":{"type":"spec","publisher":"manufacturer","name":"Guntec USA, AR-15 Heavy Duty Wide Castle Nut For Car/M4 Buffer Tube, CASTLE-HD, its Additional Information; the page as the user saved it, references/guntec-ar15-heavy-duty-castle-nut/docs/ar15-heavy-duty-wide-castle-nut-for-car-m4-buffer-tube.saved-2026-10-20.html","url":"https://guntecusa.com/product/ar15-heavy-duty-wide-castle-nut-for-car-m4-buffer-tube/","retrieved":"2026-10-20","via":"user"}},{"id":"metal","value":0.537,"unit":"oz","pm":0.12,"source":{"type":"derived","expr":"(0.785398163 * ({.od} * {.od} - {std.receiver_extension.thread_major_d} * {std.receiver_extension.thread_major_d}) * {.thickness} + 0.392699082 * ({std.receiver_extension.thread_major_d} * {std.receiver_extension.thread_major_d} - {std.receiver_extension.thread_minor_d} * {std.receiver_extension.thread_minor_d}) * {.thickness} - {.notches} * {.notch_width} * {.notch_depth} * ({.od} - {std.receiver_extension.thread_major_d}) / 2 - {.staking_notches} * {.staking_notch_width} * {.staking_notch_depth} * {.staking_notch_radial}) * {std.density.steel}","via":"harvest"},"note":"Its steel worked out from its sizes: the ring from the thread's crests out, and half the thread's depth inside them (the nut's own thread, which the model doesn't draw), less its notches. Its ± is mostly the diameter's thirty-second (0.11 oz)."}],"adopt":{"from":"guntec","reason":"Guntec's own figure; the steel its sizes hold agrees within its ±."}}}},{"subject":"guntec-ar15-mil-spec-buffer-tube-gen-2","title":"Guntec USA AR-15 Mil-Spec Buffer Tube (Gen 2)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"metal","value":3.6,"unit":"oz","pm":0.2,"source":{"type":"derived","expr":"(0.785398163 * ({.tube_od} * {.tube_od} - {std.receiver_extension.bore_d} * {std.receiver_extension.bore_d}) * {.tube_length} + 0.785398163 * {std.receiver_extension.bore_d} * {std.receiver_extension.bore_d} * {std.receiver_extension.carbine_rear_wall} + {std.receiver_extension.rail_width} * ({std.receiver_extension.rail_bottom_below_axis} - {.tube_od} / 2) * ({.tube_length} - {std.receiver_extension.rail_ramp_end}) - {.channel_width} * {.channel_depth} * ({.channel_front_from_rear} - {.channel_rear_from_rear}) - 6 * 0.785398163 * {.position_hole_d} * {.position_hole_d} * ({std.receiver_extension.rail_bottom_below_axis} - {.tube_od} / 2 - {.channel_depth})) * {std.density.aluminium}","via":"harvest"}},{"id":"guntec","value":3.3,"unit":"oz","stated":"Weight: 3.3 oz","source":{"type":"spec","publisher":"manufacturer","name":"Guntec USA, AR-15 Mil-Spec Buffer Tube (Gen 2) (Anodized Clear), MILTUBE-G2-CLEAR, its description (the same line on all twelve pages of the tube, each colour and the Plain); the page as the user saved it, references/guntec-ar15-mil-spec-buffer-tube-gen-2/docs/ar-15-mil-spec-buffer-tube-gen-2-anodized-clear.saved-2026-10-19.html","url":"https://guntecusa.com/product/ar-15-mil-spec-buffer-tube-gen-2-anodized-clear/","retrieved":"2026-10-19","via":"user"}},{"id":"guntec-specs","value":3.4,"unit":"oz","stated":"Product Weight 3.4 oz","source":{"type":"spec","publisher":"manufacturer","name":"Guntec USA, AR-15 Mil-Spec Buffer Tube (Gen 2) (Plain), MILTUBE-G2, its Additional Information (beside its height, width and length); the page as the user saved it, references/guntec-ar15-mil-spec-buffer-tube-gen-2/docs/ar-15-mil-spec-buffer-tube-gen-2-plain.saved-2026-10-19.html","url":"https://guntecusa.com/product/ar-15-mil-spec-buffer-tube-gen-2-plain/","retrieved":"2026-10-19","via":"user"},"note":"The black tube's; whether it is the tube alone or as shipped isn't said."}],"adopt":{"from":"guntec","reason":"The maker's own figure, said of this tube on every page of it (each colour and the black). Its other figure, 3.4 under the black tube's \"Product Weight\", agrees within their last digits. The metal worked out from the mil-spec sizes is 0.3 oz more: Guntec's wall, its channel's depth and its rail's underside aren't read on any view, and the formula holds the standard's; Magpul's drawing of the 7075 tube, as 6061, is 3.75. Kept beside it, and the model's volume is held to it."},"note":"Guntec's own pages (saved by the user, 2026-10-19) give two figures: \"Weight: 3.3 oz\" in the description of the tube in every colour, and \"Product Weight 3.4 oz\" in the black (Plain) tube's specifications beside its sizes. A Gen 2 copy at veriforcetactical.com (refused) is summarised as 5 oz: a lead, not a source. Before the pages came the weight was worked out from its sizes, as BCM's tube's is: the tube's wall round its bore along its length, its rear wall, and its rail less the six position holes and the channel they lie in, as 6061 (Redcon1: \"machined from T6-6061 aluminum\"; std.density.aluminium adopts 6061). A derived figure, for the build's total. Checked against Magpul's drawing of the mil-spec carbine tube, which states \"0.244 lbm\" in 7075: 3.90 oz, 3.75 oz in 6061 (4% lighter), the rail's lip, fillets and thread crests being in Magpul's and not in this formula. The ± covers that and the wall's own."},"tube_od":{"label":"The tube's outside diameter","kind":"length","measurements":[{"id":"std","value":1.148,"unit":"in","source":{"type":"derived","expr":"{std.receiver_extension.milspec_od}","via":"harvest"},"note":"The standard mil-spec carbine tube's: the sellers sell it as mil-spec."},{"id":"redcon1","value":1.148,"unit":"in","stated":"Buffer Tube Diameter Mil-Spec (1.148\")","source":{"type":"spec","publisher":"retailer","name":"Redcon1 Tactical, Guntec USA AR-15 Mil-Spec Buffer Tube Kit - Anodized Red (MILTUBESET-RED)","url":"https://redcon1tactical.com/guntec-usa-ar-15-mil-spec-buffer-tube-kit-anodized-red.html","retrieved":"2026-10-18","via":"harvest"},"note":"Guntec's red tube as sold in its set (\"6-position carbine-length Mil-Spec receiver extension machined from T6-6061 aluminum\"); the set's page doesn't say Gen 2."},{"id":"guntec","value":1.125,"unit":"in","pm":0.03125,"stated":"Product Width 1.125\"","source":{"type":"spec","publisher":"manufacturer","name":"Guntec USA, AR-15 Mil-Spec Buffer Tube (Gen 2) (Plain), MILTUBE-G2, its Additional Information; the page as the user saved it, references/guntec-ar15-mil-spec-buffer-tube-gen-2/docs/ar-15-mil-spec-buffer-tube-gen-2-plain.saved-2026-10-19.html","url":"https://guntecusa.com/product/ar-15-mil-spec-buffer-tube-gen-2-plain/","retrieved":"2026-10-19","via":"user"},"note":"Guntec's three sizes are sixteenths of an inch (1 1/8, 1 7/16, 7 1/4; 1.125 and 1.4375 are those fractions written out), so each is taken to its nearest sixteenth, a thirty-second either way: the mil-spec 1.148 is 1 1/8 to the sixteenth. Narrower than the thread's 1 3/16 crests, so it is the body's width, not the thread's."}],"adopt":{"from":"std","reason":"The standard's; the one seller's page that states a diameter for Guntec's tube says the same, and Guntec's own width, a sixteenth's figure, agrees with it."},"note":"Sold as mil-spec: the2ndtactical, \"GUNTEC AR-15|AR-10 MIL-SPEC BUFFER TUBE - ANODIZED CLEAR\" with the tags \"6 POSITION\", \"CARBINE\", \"MIL-SPEC\" (https://the2ndtactical.com/guntec-ar-15-ar-10-mil-spec-buffer-tube-anodized-clear.html, read 2026-10-18)."},"tube_front_behind_pin":{"label":"The tube's front face behind the takedown pin (how far it screws in)","kind":"length","measurements":[{"id":"std","value":0.669,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"-{std.receiver_extension.front_face_x}","via":"harvest"},"note":"The Army's drawings: a mil-spec tube is screwed in until its edge stands over the buffer retainer's shoulder."}],"note":"Hidden inside the receiver: what it moves is the rail's ramp, the channel and the six holes."},"tube_length":{"label":"The tube's length","kind":"length","measurements":[{"id":"magpul-drawing","value":7.25,"unit":"in","pm":0.02,"stated":"7.25 (the side view's overall length; \"TWO PLACE DECIMAL .020\")","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, \"M4 Receiver Extension, Carbine, Military\" partial drawing (rev A, 2008-03-24), hosted by ar15tactical.com","url":"https://ar15tactical.com/wp-content/uploads/2016/09/ar-15-milspec-buffer-tube.pdf","retrieved":"2026-10-18","via":"harvest"},"note":"The drawing of the mil-spec carbine tube, which std.receiver_extension's rail figures are read on; a stock maker's drawing of the tube its stocks fit. Guntec's is sold as a mil-spec carbine tube."},{"id":"guntec","value":7.25,"unit":"in","pm":0.03125,"stated":"Product Length 7.25\"","source":{"type":"spec","publisher":"manufacturer","name":"Guntec USA, AR-15 Mil-Spec Buffer Tube (Gen 2) (Plain), MILTUBE-G2, its Additional Information; the page as the user saved it, references/guntec-ar15-mil-spec-buffer-tube-gen-2/docs/ar-15-mil-spec-buffer-tube-gen-2-plain.saved-2026-10-19.html","url":"https://guntecusa.com/product/ar-15-mil-spec-buffer-tube-gen-2-plain/","retrieved":"2026-10-19","via":"user"},"note":"In sixteenths of an inch, as its other two sizes are (tube_od): taken to its nearest sixteenth."}],"adopt":{"from":"magpul-drawing","reason":"The two agree. Magpul's drawing is read to its two places (± 0.02), Guntec's figure to a sixteenth; the drawing's is the finer."},"note":"Guntec's own page of the black (Plain) tube states its length, 7.25 in (\"Product Length\"; saved by the user, 2026-10-19): the same figure as Magpul's drawing of the mil-spec carbine tube."},"overall_height":{"label":"The tube's height, its top to its rail's bottom","kind":"length","measurements":[{"id":"std","value":1.448,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{.tube_od} / 2 + {std.receiver_extension.rail_bottom_below_axis}","via":"harvest"},"note":"Half the mil-spec outside diameter over the axis, and Magpul's drawing's rail bottom under it."},{"id":"guntec","value":1.4375,"unit":"in","pm":0.03125,"stated":"Product Height 1.4375\"","source":{"type":"spec","publisher":"manufacturer","name":"Guntec USA, AR-15 Mil-Spec Buffer Tube (Gen 2) (Plain), MILTUBE-G2, its Additional Information; the page as the user saved it, references/guntec-ar15-mil-spec-buffer-tube-gen-2/docs/ar-15-mil-spec-buffer-tube-gen-2-plain.saved-2026-10-19.html","url":"https://guntecusa.com/product/ar-15-mil-spec-buffer-tube-gen-2-plain/","retrieved":"2026-10-19","via":"user"},"note":"1 7/16 in, in sixteenths as its other two sizes are (tube_od): taken to its nearest sixteenth."}],"adopt":{"from":"std","reason":"The figures the model is drawn to; Guntec's, to its sixteenth, agrees (1.448 is 1 7/16 to the sixteenth)."},"note":"A check of the rail's depth on Guntec's own tube: the standard's tube and rail come to it within its sixteenth."},"position_step":{"label":"The stock position step","kind":"length","measurements":[{"id":"magpul","value":0.66,"unit":"in","source":{"type":"derived","expr":"{magpul-moe-sl-carbine.position_step}","via":"harvest"},"note":"Magpul's MOE SL travel over a mil-spec carbine tube's six positions."}],"note":"A property of a mil-spec carbine tube: any stock on it moves by this. No page on file gives Guntec's."},"position_hole_d":{"label":"The position holes' diameter (in the rail)","kind":"length","measurements":[{"id":"assumed","value":0.42,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows Guntec's holes square on (the gold set's photo, 0b3672e01b07, shows them in the channel from far off at a slant). Taken as the hole a mil-spec carbine tube has, read on BCM's (bcm-receiver-extension.position_hole_d, 0.42 ± 0.03), since a stock's lock pin goes into either.","via":"harvest"}}]},"position_hole_rear_from_rear":{"label":"The rear position hole's centre ahead of the tube's rear face","kind":"length","measurements":[{"id":"assumed","value":0.44,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows Guntec's holes square on. Taken as a mil-spec carbine tube's, read on BCM's (bcm-receiver-extension.position_hole_rear_from_rear, 0.44 ± 0.03); the channel the holes lie in begins 0.45 in ahead of the rear face in the clear tube's photo (channel_rear_from_rear), which agrees.","via":"harvest"}}]},"channel_rear_from_rear":{"label":"The channel along the rail's underside, its rear end ahead of the tube's rear face","kind":"length","measurements":[{"id":"photo","value":0.45,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/guntec-ar15-mil-spec-buffer-tube-gen-2 ca79a7f5e6ca (the2ndtactical's 1200 px copy of Guntec's own photograph of the clear tube, 1b50c33def5f, a three-quarter view of its right side from in front and a little below)","scaleRef":"the tube's length (tube_length, 7.25 in) between its rear face (the rail's rear corner and the tube's top rear corner, 107 to 111 px along the axis) and the front face's centre (1211 px along the axis): 152 px/in along the tube's axis, drawn at 7° in the picture","method":"the channel's rear rounded end, at image (99, 635), projected onto the axis: 0.45 in ahead of the rear face. The ± is the picture's mild perspective (its edges converge 2.5°) and the ends' reading on a 2x crop.","via":"harvest"}}],"note":"Guntec's tube has a long shallow channel along its rail's underside with rounded ends, the six holes in its floor: seen along the rail in the clear tube's picture and from below in the gold set's (0b3672e01b07)."},"channel_front_from_rear":{"label":"The channel along the rail's underside, its front end ahead of the tube's rear face","kind":"length","measurements":[{"id":"photo","value":3.82,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/guntec-ar15-mil-spec-buffer-tube-gen-2 ca79a7f5e6ca (the2ndtactical's picture of the clear tube, 1200 px)","scaleRef":"the tube's length (tube_length, 7.25 in), 152 px/in along the axis (channel_rear_from_rear)","method":"the channel's front rounded end, at image (606, 712), projected onto the axis: 3.82 in ahead of the rear face. Behind the front hole's centre by the step's 0.66 times five from the rear hole's 0.44 (3.74), it reaches 0.08 in past it.","via":"harvest"}}]},"channel_width":{"label":"The channel along the rail's underside, its width","kind":"length","measurements":[{"id":"assumed","value":0.25,"unit":"in","pm":0.06,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows the rail's underside square on. The gold set's photo (0b3672e01b07) has the channel narrower than the rail's 0.49 and its rounded ends about half its width across; the holes (0.42) cut through its sides.","via":"harvest"}}]},"channel_depth":{"label":"The channel along the rail's underside, its depth","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows the channel in section; the clear tube's picture has it a shallow recess whose far wall shows as a thin lit band.","via":"harvest"}}]},"rail_rear_chamfer":{"label":"The rail's rear lower edge, its chamfer (along the tube)","kind":"length","measurements":[{"id":"photo","value":0.1,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/guntec-ar15-mil-spec-buffer-tube-gen-2 ca79a7f5e6ca (the2ndtactical's picture of the clear tube, 1200 px)","scaleRef":"the tube's length (tube_length, 7.25 in), 152 px/in along the axis (channel_rear_from_rear)","method":"the chamfer's two ends on the rail's rear lower corner, image (32, 613) and (45, 635) on a 3x crop, projected onto the axis: 15.6 px. Only its length along the tube is read: its height is foreshortened in this view.","via":"harvest"}}],"note":"The rail's rear end is cut off at its lower edge in every photograph of Guntec's tube that shows it: the clear tube's picture (ca79a7f5e6ca), ABC Sportz's clear set (84ec785b7c42) and its gold set from below (0b3672e01b07). Drawn at 45° (the angle is an assumption: no view on file is square to the rail's side)."},"thread_crests":{"label":"The thread's crests, counted along the tube's top line","kind":"count","measurements":[{"id":"photo","value":18.5,"unit":"count","pm":1,"source":{"type":"photo","photo":"references/guntec-ar15-mil-spec-buffer-tube-gen-2 ca79a7f5e6ca (the clear tube's picture, its top line on a 4x crop) and eabe3e83f28b (Redcon1's photograph of the red tube, on a 5x crop)","scaleRef":"none: a count","method":"crests counted from the body's shoulder to the plain lip at the mouth: 18 to 19 in each","via":"harvest"}}],"note":"A check of the standard's thread length on Guntec's own tube: std.receiver_extension.thread_length (the reference model's 1.181) at 16 to the inch is 18.9 turns."}}},{"subject":"guntec-ar15-stainless-carbine-buffer","title":"Guntec USA AR-15 Stainless Steel Car Buffer (CARBUF-SS)","dimensions":{"weight":{"label":"Weight (its class: carbine, H, H2…)","kind":"mass","measurements":[{"id":"guntec","value":3.2,"unit":"oz","pm":0.05,"stated":"3.2 oz weight","source":{"type":"spec","publisher":"manufacturer","name":"Guntec USA, AR-15 Stainless Steel Car Buffer, CARBUF-SS, its description (\"CAR/M4 Standard Buffer No Moving Internal Weights, One Solid Unit 3.2 oz weight Reduces Noise and Friction Compared To Standard Buffers Mil-Spec Dimensions Stainless Steel, Black Neoprene Head\"); the page as the user saved it, references/guntec-ar15-stainless-carbine-buffer/docs/ar-15-stainless-steel-car-buffer.saved-2026-10-20.html","url":"https://guntecusa.com/product/ar-15-stainless-steel-car-buffer/","retrieved":"2026-10-20","via":"user"}}],"note":"Redcon1 Tactical's \"Buffer Weight: 3.0 oz (Carbine)\" is said of the buffer tube set's buffer, Guntec's CARBUF, though its picture of the set has this one: not this buffer's figure, and left out. A search summary of another copy of Guntec's page gave \"Product Weight 2.8 oz\"; the page the user saved has no such line."},"length":{"label":"Length (the head's front face to the bumper's end)","kind":"length","measurements":[{"id":"std","value":3.251,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.carbine_buffer.length}","via":"harvest"},"note":"The standard carbine buffer's, by Guntec's \"Mil-Spec Dimensions\" (its page, as the user saved it). Its pictures don't read it better: Guntec's own (627dce494537, 900 px) is an oblique from above on the diagonal, the head's face and the bumper's end showing, and the sellers' pictures of the set have it in its spring, seen obliquely. Their pattern is the standard's: a head with a flat on its rim, the step behind it, the pin's hole beside a tapered bumper with a flat end."}]},"od":{"label":"Diameter (its head, which runs in the extension's bore)","kind":"length","measurements":[{"id":"std","value":0.98,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.carbine_buffer.head_d}","via":"harvest"},"note":"The standard's, by Guntec's \"Mil-Spec Dimensions\"."}]}}},{"subject":"hexmag-series-2-ar15-30","title":"Hexmag AR-15/M4/M16 Magazine Series 2 (30RD)","dimensions":{"overall_height":{"label":"Overall height, feed lips to base","kind":"length","measurements":[{"id":"hexmag","value":7.5,"unit":"in","pm":0.1,"stated":"Dimensions 7.5 × 2.66 × 1.125 in","source":{"type":"spec","publisher":"manufacturer","name":"Hexmag, HEXMAG AR-15/M4/M16 Magazine Series 2 (30RD), Additional information","url":"https://hexmag.com/product/hexmag-ar-15-m4-m16-magazine-series-2-30-rds/","retrieved":"2026-11-03","via":"harvest"}},{"id":"well","value":7.366,"unit":"in","pm":0.09,"source":{"type":"derived","expr":"({std.ar15.magwell_front_inner_x} - {bad-workhorse-lower.magazine_seat_x}) * {.patent_height_px} / {.patent_top_px}"},"note":"The patent's top section, scale free (patent_top_px over patent_height_px), standing from the seat every lower on file gives a magazine's spine to the well's front wall: the most the magazine can be. The ± is the seat's (0.03, a photo of another magazine seated) and the wall's over the ratio."}],"adopt":{"from":"well","reason":"What the magazine has to fit: at Hexmag's 7.5 the drawing's top section stands 0.043 in through a standard well's front wall. Hexmag's figure is a half inch's rounding; the two agree within their ±."},"note":"Hexmag's page gives \"Dimensions 7.5 × 2.66 × 1.125 in\" (its markup: depth 7.5, width 2.66, height 1.125 INH), and its 10-round's page the same line, for the same full-length body (\"HEXMAG's patented True Riser System inside of a standard sized body\"; \"10 and 15 round magazines use full length bodies\", hexmag.com/polyhex2-magazines/). Read as the height standing upright and laid on the patent's side elevation, it makes the top section 2.576 in from the spine to the front: seated where every lower on file seats a magazine's spine (magazine_seat_x, 0.0195 in ahead of the spine slot's rear wall), its front stood 0.043 in into the well's front wall and its sides 0.005 into the side walls, which a magazine sold for AR-15s can't. The two can't both be true, and what the magazine has to fit decides (2026-11-03, round 2): the scale is the one at which the patent's top section reaches the well's front wall from that seat and no further, 1.8% under Hexmag's figure. Cross-checks at that scale: the top section 0.887 across in a .898 well (0.005 a side) and its body ahead of the spine 2.389 in a 2.398 box; its catch window (1.027 to 0.507 in from the spine) over the lower's catch slot; the catch notch read on Primary Arms' photo of the Series 2 1.057 under the lips, 0.013 from the PMAG 30's 1.07, two magazines fed by one bolt; and the photo's own proportions, its silhouette on the patent's at IoU 0.96 with the scale free (the photo, from a little above, reads the top section 1% shorter for its height, the way an elevated view stretches heights). Hexmag's 7.5 is kept as published: likeliest the height rounded to the half inch (7.366 here; the longest straight line across the magazine, from the lips' rear to the floorplate's front, is 7.4)."},"patent_top_px":{"label":"The patent's side elevation: its top section's front to back, in the figure's pixels","kind":"count","measurements":[{"id":"patent","value":768,"unit":"count","source":{"type":"photo","photo":"references/hexmag-series-2-ar15-30 704a55423214 (US D727,456 S (Hexmag, 'Ammunition magazine'), FIG. 2: the side with the catch notch, the magazine's left, 300 dpi)","scaleRef":"the figure's own pixels","method":"the side outline's greatest reach from the spine's rear face to the front over the top section where it stands in the well (0.4 to 2.55 in under the top: its front face is upright to a pixel, 2.534 to 2.537 in at the adopted scale, and the spine's rear face upright from the rib's top down), ± 1 px","via":"harvest"}}]},"patent_height_px":{"label":"The patent's side elevation: the magazine's height, in the figure's pixels","kind":"count","measurements":[{"id":"patent","value":2233,"unit":"count","source":{"type":"photo","photo":"references/hexmag-series-2-ar15-30 704a55423214 (US D727,456 S (Hexmag, 'Ammunition magazine'), FIG. 2: the side with the catch notch, the magazine's left, 300 dpi)","scaleRef":"the figure's own pixels","method":"the traced outline's y-extent, from the lips' top to the floorplate's lowest point (tools/trace.py's own count)","via":"harvest"}}]},"body_height":{"label":"Body height below the feed-lip block","kind":"length","measurements":[],"note":"Onboarding checklist: Side view; overall_height minus the feed-lip block when the block is shared across a product line. Not read: the patent's side elevation draws no line where a feed-lip block would end, and nothing here needs it."},"feed_lip_block_height":{"label":"Feed-lip block height","kind":"length","measurements":[],"note":"Onboarding checklist. Not read (as body_height)."},"front_to_back":{"label":"Front to back at the body top","kind":"length","measurements":[{"id":"patent","value":2.53,"unit":"in","pm":0.036,"source":{"type":"photo","photo":"references/hexmag-series-2-ar15-30 704a55423214 (US D727,456 S (Hexmag, 'Ammunition magazine'), FIG. 2: the side with the catch notch, the magazine's left (the patent's 'right side elevation'), 300 dpi)","scaleRef":"scale from hexmag-series-2-ar15-30.overall_height = 7.366 in (y-extent 2233 px → 303.1 px/in)","method":"width in y [-1.4, -0.7] of the traced outline (tools/trace.py); the top section's front to back, where it stands straight in the well (between the lips' block and the frame's step)","via":"harvest"}}],"note":"Onboarding checklist: Side view; same calibration as the heights."},"catch_notch_top":{"label":"Magazine catch notch (left side), its upper edge below the feed lips' top","kind":"length","measurements":[{"id":"photo","value":1.057,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/hexmag-series-2-ar15-30 a6d8da1fb8b2 (Primary Arms' photo of HX30-AR15S2-BLK's left side, near straight, a little from behind and above, 5000 px)","scaleRef":"the photo's silhouette fitted to the patent's FIG. 2 (scale, turn and shift free; 1.3353 photo px to a figure px, turned 1.61 degrees, IoU 0.960: .cache/hexmag/register.py), so read in the figure's pixels and at its scale, hexmag-series-2-ar15-30.overall_height = 7.366 in over the figure's 2233 px: 303.1 px/in (profiles.side); y from the top of the lips (row 563.5, the outline's stroke), x from the outline's rearmost point (column 1723, the spine's rear face, mirrored)","method":"the catch's window is the darkest thing on that side (luminance under 75 of 255, the pocket 82, the side 108), inside a box picked round it ([2700, 595, 3000, 740]); its 1st percentile down the body is the figure's row 883.8: (883.8 - 563.5) / 303.15. ± the fit (2.8 figure px), the photo's lean from above and the threshold","via":"harvest"}},{"id":"patent","value":1.098,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/hexmag-series-2-ar15-30 704a55423214 (US D727,456 S (Hexmag, 'Ammunition magazine'), FIG. 2: the side with the catch notch, the magazine's left, 300 dpi)","scaleRef":"hexmag-series-2-ar15-30.overall_height = 7.366 in over the figure's 2233 px: 303.1 px/in (profiles.side); y from the top of the lips (row 563.5, the outline's stroke), x from the outline's rearmost point (column 1723, the spine's rear face, mirrored)","method":"the window's upper line (drawn heavy, rows 892 to 901, its middle 896.5) on columns 1460, 1490 and 1520: (896.5 - 563.5) / 303.15; ± half the heavy line's width and a pixel","via":"harvest"},"note":"The design patent the magazine bears, drawn in 2013 for the Series 1; its outline and its panels lie on the Series 2's photo (IoU 0.96)."}],"adopt":{"from":"photo","reason":"The product itself, as the PMAGs' are read; the patent's drawing agrees within the two readings' ±."},"note":"What seats it: the notch's upper edge hangs on the lower's catch (the `magwell` anchor). Read on the Series 2 itself (Primary Arms' near-straight photo of the left side, through the fit of the patent's silhouette to the photo's) and on the patent's side elevation: 0.041 in apart, inside the two ±. Both at the scale the well gives (overall_height; read again 2026-11-03, round 2: 1.076 and 1.119 at Hexmag's 7.5 in). The photo's reading is 0.013 from the PMAG 30's own (magpul-pmag-30-gen-m3.catch_notch_top, 1.07), as two magazines that feed from one bolt would have it, and seated by it the lips are under the carrier (the test)."},"catch_notch_height":{"label":"Magazine catch notch (left side), its height","kind":"length","measurements":[{"id":"patent","value":0.27,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/hexmag-series-2-ar15-30 704a55423214 (US D727,456 S (Hexmag, 'Ammunition magazine'), FIG. 2: the side with the catch notch, the magazine's left, 300 dpi)","scaleRef":"hexmag-series-2-ar15-30.overall_height = 7.366 in over the figure's 2233 px: 303.1 px/in (profiles.side); y from the top of the lips (row 563.5, the outline's stroke), x from the outline's rearmost point (column 1723, the spine's rear face, mirrored)","method":"the window's upper and lower lines' middles on columns 1460 to 1520: rows 896.5 and 978.5, 82 px. Taller than a lower's catch slot (std.ar15.mag_catch_slot_h, 0.252), as a window the catch comes into is. (On the photo the dark runs on 0.04 in further down, into the shadow under the window's lower edge.)","via":"harvest"}}]},"catch_notch_rear_x":{"label":"Magazine catch notch (left side), its rear end ahead of the spine's rear face","kind":"length","measurements":[{"id":"patent","value":0.507,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/hexmag-series-2-ar15-30 704a55423214 (US D727,456 S (Hexmag, 'Ammunition magazine'), FIG. 2: the side with the catch notch, the magazine's left, 300 dpi)","scaleRef":"hexmag-series-2-ar15-30.overall_height = 7.366 in over the figure's 2233 px: 303.1 px/in (profiles.side); y from the top of the lips (row 563.5, the outline's stroke), x from the outline's rearmost point (column 1723, the spine's rear face, mirrored)","method":"the window's rear line on row 940: columns 1565 to 1574, its middle 1569.5: (1723 - 1569.5) / 303.15","via":"harvest"},"note":"On the photo, through the fit, the dark window's rear end reads 0.06 in further back (0.457, its 99th percentile), where the photo looks a little from behind into the window."}]},"catch_notch_front_x":{"label":"Magazine catch notch (left side), its front end ahead of the spine's rear face","kind":"length","measurements":[{"id":"patent","value":1.027,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/hexmag-series-2-ar15-30 704a55423214 (US D727,456 S (Hexmag, 'Ammunition magazine'), FIG. 2: the side with the catch notch, the magazine's left, 300 dpi)","scaleRef":"hexmag-series-2-ar15-30.overall_height = 7.366 in over the figure's 2233 px: 303.1 px/in (profiles.side); y from the top of the lips (row 563.5, the outline's stroke), x from the outline's rearmost point (column 1723, the spine's rear face, mirrored)","method":"the window's front line on row 940: columns 1407 to 1416, its middle 1411.5: (1723 - 1411.5) / 303.15 (the window 0.53 in long)","via":"harvest"},"note":"On the photo, through the fit, 0.997 (its 1st percentile)."}]},"catch_block_proud":{"label":"The block under the catch notch (left side), standing out of the side","kind":"length","measurements":[{"id":"patent","value":0.048,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/hexmag-series-2-ar15-30 533d2a4dcb87 (US D727,456 S (Hexmag), FIG. 4: the rear elevation, 300 dpi)","scaleRef":"hexmag-series-2-ar15-30.overall_height = 7.366 in over the figure's 2234 px: 303.3 px/in (profiles.rear)","method":"row 940: the block's outer line at columns 1068 to 1072 (middle 1070), the side's at 1083 to 1086 (1084.5): 14.5 px","via":"harvest"}}],"note":"The rear elevation draws a block standing out of the left side under the notch (rows 918 to 985, 1.42 to 1.65 in under the top), its lower end chamfered back into the side; the side elevation draws it as a trapezoid under the window, and the Series 2's photo has it there. As read it would stand 0.05 in into the left wall of a standard well under the catch's slot (std.ar15.magwell_width), as the PMAG's does (magpul-pmag-30-gen-m3.catch_block_proud): not drawn until that is reconciled, and kept here."},"spine_depth":{"label":"The spine: how far its rear face stands behind the body's rear face beside it, in the well","kind":"length","measurements":[{"id":"patent-side","value":0.145,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/hexmag-series-2-ar15-30 704a55423214 (US D727,456 S (Hexmag, 'Ammunition magazine'), FIG. 2: the side with the catch notch, the magazine's left, 300 dpi)","scaleRef":"hexmag-series-2-ar15-30.overall_height = 7.366 in over the figure's 2233 px: 303.1 px/in (profiles.side); y from the top of the lips (row 563.5, the outline's stroke), x from the outline's rearmost point (column 1723, the spine's rear face, mirrored)","method":"rows 720 to 1100: the spine's rear line at columns 1720 to 1725 (middle 1722), the body's rear face beside it at 1677 to 1680 (1678, the line the top of the lips' block is on, row 600): 44 px","via":"harvest"}},{"id":"patent-plan","value":0.145,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/hexmag-series-2-ar15-30 623ea795e0e4 (US D727,456 S (Hexmag), FIG. 6: the top plan, on the sheet with FIG. 7, 300 dpi)","scaleRef":"the drawing's one scale, 303.1 px/in (its side and rear elevations')","method":"the spine's rear end (rows 521 to 525 on columns 1220 and 1260) to the body's rear face beside it (row 565, columns 1118 to 1169 and 1300 to 1347): 44 px","via":"harvest"},"note":"The plan of the same drawing."}],"adopt":{"from":"patent-side","reason":"The figure the side outline is traced from; the plan agrees to the pixel."},"note":"The spine is what stands in the well's slot for it (std.ar15.magwell_spine_slot_width; the slot is std.ar15.magwell_length - std.ar15.magwell_box_length, 0.155, deep). Two figures of the one drawing, which has its views at one scale (FIG. 2 303.1, FIG. 4 303.3 px/in)."},"spine_width":{"label":"The spine's width, where it stands in the well's slot","kind":"length","measurements":[{"id":"patent","value":0.457,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/hexmag-series-2-ar15-30 533d2a4dcb87 (US D727,456 S (Hexmag), FIG. 4: the rear elevation, 300 dpi)","scaleRef":"hexmag-series-2-ar15-30.overall_height = 7.366 in over the figure's 2234 px: 303.3 px/in (profiles.rear)","method":"rows 700, 800 and 1000: the two lines either side of the middle (column 1219.5) at 1150.5 and 1289, 138.5 px: the pair whose spacing is the slot's (the others: 1139.5 and 1301, 161.5 px; 1178.5 and 1261.5, 83 px)","via":"harvest"},"note":"Under the well's slot for it, std.ar15.magwell_spine_slot_width (0.47)."}]},"spine_top":{"label":"The spine's upper end below the top of the lips","kind":"length","measurements":[{"id":"patent","value":0.476,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/hexmag-series-2-ar15-30 704a55423214 (US D727,456 S (Hexmag, 'Ammunition magazine'), FIG. 2: the side with the catch notch, the magazine's left, 300 dpi)","scaleRef":"hexmag-series-2-ar15-30.overall_height = 7.366 in over the figure's 2233 px: 303.1 px/in (profiles.side); y from the top of the lips (row 563.5, the outline's stroke), x from the outline's rearmost point (column 1723, the spine's rear face, mirrored)","method":"column 1722, the spine's rear line, is ink from row 708 to row 1188: (708 - 563.5) / 303.15; above it the rear is the lips' block, at the body's rear face","via":"harvest"}}]},"spine_bottom":{"label":"The spine's lower end below the top of the lips, where the bars down the rear begin","kind":"length","measurements":[{"id":"patent","value":2.061,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/hexmag-series-2-ar15-30 704a55423214 (US D727,456 S (Hexmag, 'Ammunition magazine'), FIG. 2: the side with the catch notch, the magazine's left, 300 dpi)","scaleRef":"hexmag-series-2-ar15-30.overall_height = 7.366 in over the figure's 2233 px: 303.1 px/in (profiles.side); y from the top of the lips (row 563.5, the outline's stroke), x from the outline's rearmost point (column 1723, the spine's rear face, mirrored)","method":"column 1722 is ink to row 1188: (1188 - 563.5) / 303.15","via":"harvest"}}]},"grip_top":{"label":"The gripping section's upper edge at the rear, below the top of the lips (where the sides step out)","kind":"length","measurements":[{"id":"patent","value":2.77,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/hexmag-series-2-ar15-30 533d2a4dcb87 (US D727,456 S (Hexmag), FIG. 4: the rear elevation, 300 dpi)","scaleRef":"hexmag-series-2-ar15-30.overall_height = 7.366 in over the figure's 2234 px: 303.3 px/in (profiles.rear)","method":"the rear outline's step from the top section's width to the gripping section's: from y -2.758 to -2.882 on the left, -2.795 to -2.875 on the right (profiles.rear); its middle","via":"harvest"}}]},"hex_panels":{"label":"The HEXTURE panels on each side's main field","kind":"count","measurements":[{"id":"patent","value":28,"unit":"count","source":{"type":"photo","photo":"references/hexmag-series-2-ar15-30 704a55423214 (US D727,456 S (Hexmag, 'Ammunition magazine'), FIG. 2: the side with the catch notch, the magazine's left, 300 dpi)","scaleRef":"a count","method":"the lattice's cells with a panel in them (profiles.side features.hexes; FIG. 3, profiles.right, has the same 28 cells mirrored)","via":"harvest"}}],"note":"Counted on the patent's two side elevations, each panel a cell of one honeycomb (its lattice fitted to the twelve full hexagons of each figure: spacing 201.0 px, 0.675 in, 60.0 degrees, 0.7 px rms: .cache/hexmag/hexfield.py), and on the Series 2's photo of its left side, where every one of them lies (the fit of the patent's silhouette to the photo's: .cache/hexmag/crops/reg_left.png). Fourteen are whole hexagons; the rest are cut short at the front strip, the spine and the floorplate. Two more in the channel down the front of the upper body (hex_panels_front)."},"hex_panels_front":{"label":"The HEXTURE panels in the channel down the front of the upper body, each side","kind":"count","measurements":[{"id":"patent","value":2,"unit":"count","source":{"type":"photo","photo":"references/hexmag-series-2-ar15-30 704a55423214 (US D727,456 S (Hexmag, 'Ammunition magazine'), FIG. 2: the side with the catch notch, the magazine's left, 300 dpi)","scaleRef":"a count","method":"under the stripper-clip guides: a pentagon and a panel cut short by the channel's lines (profiles.side features.hexes_front), as the Series 2's photos have them","via":"harvest"}}]},"hex_band":{"label":"The groove between two HEXTURE panels, its width","kind":"length","measurements":[{"id":"patent","value":0.081,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/hexmag-series-2-ar15-30 704a55423214 (US D727,456 S (Hexmag, 'Ammunition magazine'), FIG. 2: the side with the catch notch, the magazine's left, 300 dpi)","scaleRef":"hexmag-series-2-ar15-30.overall_height = 7.366 in over the figure's 2233 px: 303.1 px/in (profiles.side); y from the top of the lips (row 563.5, the outline's stroke), x from the outline's rearmost point (column 1723, the spine's rear face, mirrored)","method":"the lattice's spacing (201.0 px) less a panel's width across its flats, its outline's middle (twice 85.3 px of white inside a full hexagon, plus the line's half each side: 176.6 px): 24.4 px","via":"harvest"}}]},"hex_proud":{"label":"The HEXTURE panels: how far they stand out of the groove between them","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows a panel's edge in profile.","via":"harvest"}}],"note":"KYGUNCO's words for it: \"Its lightweight composite body features a raised hexagon grip pattern\". No view on file has a panel's edge in profile: the rear elevation's sides carry a second line 13 to 14 px (0.045 in) inside the silhouette over the gripping section, which may be the groove's floor or the spine strip's edge; the photos show the grooves as a lit and a dark wall a few hundredths across."},"vee_depth":{"label":"The stripper-clip guides: how deep their two wedges are sunk","kind":"length","measurements":[{"id":"assumed","value":0.04,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows the guides in profile.","via":"harvest"}}]},"follower_thickness":{"label":"The follower's top, as much of it as the model draws between the lips","kind":"length","measurements":[{"id":"assumed","value":0.06,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the model is solid, and the follower is drawn as the top of it between the lips, this thick; no view on file shows the follower in section.","via":"harvest"}}]},"hexid_across":{"label":"The HexID latch plate in the floorplate: its hexagon across its corners","kind":"length","measurements":[{"id":"patent","value":0.474,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/hexmag-series-2-ar15-30 623ea795e0e4 (US D727,456 S (Hexmag), FIG. 7: the bottom plan, 300 dpi)","scaleRef":"the floorplate's own width in the same view, hexmag-series-2-ar15-30.floorplate_width (1.105 in over its 320 px, columns 1065 to 1385)","method":"the hexagon's two corners on row 2165, columns 1155 and 1295: 140 px; it stands at the middle of the floorplate's length (its middle 15 px behind the floorplate's, of 680)","via":"harvest"}}]},"hexid_depth":{"label":"The HexID latch plate: how deep its pocket is in the floorplate","kind":"length","measurements":[{"id":"assumed","value":0.05,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the plate is drawn flush in a pocket this deep; no view on file shows it in section.","via":"harvest"}}]},"hang_below_magwell":{"label":"Hang below the magwell when seated","kind":"length","measurements":[{"id":"seated","value":4.676,"unit":"in","pm":0.15,"source":{"type":"derived","expr":"{bad-workhorse-lower.magwell_bottom_center_y} - ({std.ar15.mag_catch_slot_bottom_y} + {std.ar15.mag_catch_slot_h} + {.catch_notch_top} - {.overall_height})"}}],"note":"From the well's mouth at its middle down to the floorplate's lowest point, hung by its notch on the catch's upper face (the Army drawing's slot), in the one lower on file whose mouth is measured, the Workhorse (as the PMAGs' are). A check on the seat, not what seats it."},"weight":{"label":"Weight, empty","kind":"mass","measurements":[{"id":"hexmag","value":4.55,"unit":"oz","stated":"Weight 4.55 oz","source":{"type":"spec","publisher":"manufacturer","name":"Hexmag, HEXMAG AR-15/M4/M16 Magazine Series 2 (30RD), Additional information","url":"https://hexmag.com/product/hexmag-ar-15-m4-m16-magazine-series-2-30-rds/","retrieved":"2026-11-03","via":"harvest"}},{"id":"kygunco","value":1,"unit":"lb","pm":0.5,"stated":"Weight 1 lb","source":{"type":"spec","publisher":"retailer","name":"KYGUNCO, HEXMAG Series 2 Gray Detachable 30rd Multi-Cal AR-15 (Style HXM-HX30-AR-GRY)","url":"https://www.kygunco.com/product/hexmag-series-2-gray-detachable-30rd-multi-cal-ar-15","retrieved":"2026-11-03","via":"harvest"},"note":"A shop's weight rounded to the pound, as a carton ships."}],"adopt":{"from":"hexmag","reason":"The maker's own figure for the magazine; KYGUNCO's is a shipping weight rounded to the pound."},"note":"Hexmag's figure for the 30-round (its markup: weight 4.55 ONZ). Its 10-round page gives 4.9 oz for the same body with a riser and a fixed base plate in it: another product's weight, kept apart (not a reading of this one). KYGUNCO's \"Weight 1 lb\" for the gray is a shipping figure (a pound for a magazine of polymer is three times Hexmag's), kept beside it."},"stated_length":{"label":"Length as the manufacturer states it (reference points undefined)","kind":"length","measurements":[],"note":"Onboarding checklist. Hexmag's page states no length apart from its three sizes (overall_height, stated_front_to_back, stated_width). Shiner's page says \"Length 8.6500\" with no unit and no reference: not taken."},"stated_front_to_back":{"label":"Hexmag's second size, 2.66 in (its markup's \"width\"): what it spans is not stated","kind":"length","measurements":[{"id":"hexmag","value":2.66,"unit":"in","stated":"Dimensions 7.5 × 2.66 × 1.125 in","source":{"type":"spec","publisher":"manufacturer","name":"Hexmag, HEXMAG AR-15/M4/M16 Magazine Series 2 (30RD), Additional information (markup: \"width\":{\"unitCode\":\"INH\",\"value\":\"2.66\"})","url":"https://hexmag.com/product/hexmag-ar-15-m4-m16-magazine-series-2-30-rds/","retrieved":"2026-11-03","via":"harvest"}}]},"stated_width":{"label":"Hexmag's third size, 1.125 in (its markup's \"height\"): what it spans is not stated","kind":"length","measurements":[{"id":"hexmag","value":1.125,"unit":"in","stated":"Dimensions 7.5 × 2.66 × 1.125 in","source":{"type":"spec","publisher":"manufacturer","name":"Hexmag, HEXMAG AR-15/M4/M16 Magazine Series 2 (30RD), Additional information (markup: \"height\":{\"unitCode\":\"INH\",\"value\":\"1.125\"})","url":"https://hexmag.com/product/hexmag-ar-15-m4-m16-magazine-series-2-30-rds/","retrieved":"2026-11-03","via":"harvest"}}]},"spine_ahead_of_rearmost":{"label":"The spine's rear face where the top section stands in the well, ahead of the side outline's rearmost point","kind":"length","measurements":[{"id":"patent","value":0,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/hexmag-series-2-ar15-30 704a55423214 (US D727,456 S (Hexmag, 'Ammunition magazine'), FIG. 2: the side with the catch notch, the magazine's left (the patent's 'right side elevation'), 300 dpi)","scaleRef":"scale from hexmag-series-2-ar15-30.overall_height = 7.366 in (y-extent 2233 px → 303.1 px/in)","method":"x_min in y [-1.4, -0.7] of the traced outline (tools/trace.py); the spine's rear face where the top section stands in the well, ahead of the outline's rearmost point","via":"harvest"}}]},"width":{"label":"The top section's width, where it stands in the well","kind":"length","measurements":[{"id":"patent","value":0.887,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/hexmag-series-2-ar15-30 533d2a4dcb87 (US D727,456 S (Hexmag), FIG. 4: the rear elevation (the magazine's left on the viewer's left), 300 dpi)","scaleRef":"scale from hexmag-series-2-ar15-30.overall_height = 7.366 in (y-extent 2234 px → 303.3 px/in)","method":"width in y [-1.6, -0.9] of the traced outline (tools/trace.py); the top section's width where it stands in the well, under the lips and over the catch's block and the frame's step","via":"harvest"}}]},"grip_width":{"label":"The gripping section's width, over its HEXTURE panels","kind":"length","measurements":[{"id":"patent","value":0.94,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/hexmag-series-2-ar15-30 533d2a4dcb87 (US D727,456 S (Hexmag), FIG. 4: the rear elevation (the magazine's left on the viewer's left), 300 dpi)","scaleRef":"scale from hexmag-series-2-ar15-30.overall_height = 7.366 in (y-extent 2234 px → 303.3 px/in)","method":"width in y [-6.0, -3.5] of the traced outline (tools/trace.py); the gripping section's width over the HEXTURE panels, above the floorplate","via":"harvest"}}]},"floorplate_width":{"label":"The floorplate's width, its widest","kind":"length","measurements":[{"id":"patent","value":1.085,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/hexmag-series-2-ar15-30 533d2a4dcb87 (US D727,456 S (Hexmag), FIG. 4: the rear elevation (the magazine's left on the viewer's left), 300 dpi)","scaleRef":"scale from hexmag-series-2-ar15-30.overall_height = 7.366 in (y-extent 2234 px → 303.3 px/in)","method":"width in y [-7.45, -7.0] of the traced outline (tools/trace.py); the floorplate's width, its widest","via":"harvest"}}]},"floorplate_height":{"label":"The floorplate: from the joint along its upper edge down to its underside, measured upright","kind":"length","measurements":[{"id":"patent","value":0.31,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/hexmag-series-2-ar15-30 704a55423214 (US D727,456 S (Hexmag, 'Ammunition magazine'), FIG. 2: the side with the catch notch, the magazine's left, 300 dpi)","scaleRef":"hexmag-series-2-ar15-30.overall_height = 7.366 in over the figure's 2233 px: 303.1 px/in (profiles.side)","method":"the joint's upper line and the underside's line on columns 760, 900, 1100 and 1300: rows 2511.5 and 2605, 2550 and 2644, 2605.5 and 2702.5, 2660 and 2757.5: 93.5, 94, 97 and 97.5 px, their mean 95.5 less a stroke's half at the underside (the outline is inset 2 px)","via":"harvest"}}],"note":"The side elevation draws the floorplate under a pair of lines along the joint, 20 px apart (the body's rim, then the floorplate's own upper edge), both leaning as the underside does (15.4 and 15.8 degrees); from the upper one, where the body ends, to the underside. The joint is taken as a line that far above the side outline's underside, parallel to it."},"name_block_depth":{"label":"The name block on the right side: how deep its panel is sunk","kind":"length","measurements":[{"id":"assumed","value":0.01,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows the panel in profile; Primary Arms' photo of the right side has its edge as a thin lit line under a dark one, as a shallow sunk panel's.","via":"harvest"}}]}}},{"subject":"holosun-aro-163-mount","title":"Holosun's 1.63 in lower 1/3 co-witness pedestal mount, the mount the ARO is sold on (sold alone as HS-MOUNT-AR-RISER-ARO)","dimensions":{"deck_above_rail":{"label":"The deck's top (where a dot's base sits) above the rail's top","kind":"length","measurements":[{"id":"page-less-aro","value":0.728,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{holosun-aro.optical_axis_above_rail} - {holosun-aro.axis_above_base}","via":"harvest"},"note":"1.63 in less the ARO's 0.902 in."}],"note":"Holosun gives the mount's height only as the ARO's axis on it: \"Central Mount Height 1.63\"\" (its page). Less the ARO's own axis over its base it is the deck's height; another Micro-footprint dot on it stands as much higher or lower as its own axis is over its base (D101). The EU shop's \"Size: 45x31x35 mm\" for the mount sold alone isn't a height of it: 35 mm from the clamp's foot would put the deck 1.15 in over the rail and the ARO's axis at 2.05 in, and the older HS-MOUNT-AR-RISER for Holosun's 403, 503 and 515 is given the same 45x31x35 mm and 44 g."},"deck_x":{"label":"The footprint's middle along the deck, ahead of the clamp's middle","kind":"length","measurements":[{"id":"stem","value":0.01,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{holosun-aro.cross_bolt_x}","via":"harvest"},"note":"The stem stands over the cross bolt, and the deck on the stem (Holosun's pictures of the mount alone, and its manual's Fig 6, the four screws at the deck's corners about it); the housing's base, its underside's two ends (holosun-aro.skirt_bottom_rear_x, skirt_bottom_front_x), is centred 0.0075 in ahead of it. No view shows the screws' places along the rail: the footprint's middle is taken to be the stem's."}]},"mount_length":{"label":"The clamp's length along the rail","kind":"length","measurements":[{"id":"photos","value":1.486,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{holosun-aro.mount_length}","via":"harvest"},"note":"Read on Holosun's two side photos of the pair through their cameras, in the sight's ledger."}]},"clamp_below_rail":{"label":"The clamp's bottom below the rail's top","kind":"length","measurements":[{"id":"photos","value":0.227,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{holosun-aro.clamp_below_rail}","via":"harvest"}}]},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"page","value":1.73,"unit":"oz","source":{"type":"derived","expr":"{holosun-aro.mount_weight}","via":"harvest"},"note":"Holosun's page, in the sight's ledger."},{"id":"eu","value":44,"unit":"g","stated":"Weight: 44 g","source":{"type":"spec","publisher":"manufacturer","name":"Holosun EU shop, \"Holosun high fixed mount one-piece HS-MOUNT-AR-RISER-ARO, accessory for Holosun red dot sight ARO-CORE\" (product 70195767)","url":"https://www.holosun.eu/p/70195767","retrieved":"2026-11-05","via":"harvest"}}],"adopt":{"from":"page","reason":"Holosun's own page for the sight, beside the 1.63 in mount it calls its central mount; the pair's weight has been the sight's 3.38 oz and this since the part was drawn. The EU shop's 44 g, 5 g less, may leave out the screws or the bolt, and is the figure it gives the older riser too: kept, a visible conflict."},"note":"Holosun's US page gives \"Mount Weight 1.73 oz\" beside its two mounts, and the EU shop 44 g for this one sold alone; neither says what it includes (the screws, the cross bolt and its nut). The older riser for Holosun's other Micro dots is given the same 44 g on the same shop."}}},{"subject":"holosun-aro","title":"Holosun ARO 2 MOA red dot (ARO-RD2; Holosun now lists it as ARO-CORE-RD-2)","dimensions":{"length":{"label":"Length","kind":"length","measurements":[{"id":"spec","value":2.48,"unit":"in","stated":"2.48\" × 1.54\" × 2.63\"","source":{"type":"spec","publisher":"manufacturer","name":"holosun.com ARO-CORE-RD-2 page","url":"https://www.holosun.com/products/aro-core-rd-2","retrieved":"2026-09-30","via":"harvest"},"note":"Holosun's usual L × W × H order."},{"id":"eu","value":63,"unit":"mm","stated":"63x39x67 mm","source":{"type":"spec","publisher":"manufacturer","name":"Holosun EU shop","url":"https://www.holosun.eu/en/p/70183184","retrieved":"2026-09-30","via":"harvest"}}],"adopt":{"from":"spec","reason":"Manufacturer product page; the EU listing agrees."}},"width":{"label":"Width","kind":"length","measurements":[{"id":"spec","value":1.54,"unit":"in","stated":"2.48\" × 1.54\" × 2.63\"","source":{"type":"spec","publisher":"manufacturer","name":"holosun.com ARO-CORE-RD-2 page","url":"https://www.holosun.com/products/aro-core-rd-2","retrieved":"2026-09-30","via":"harvest"}},{"id":"eu","value":39,"unit":"mm","stated":"63x39x67 mm","source":{"type":"spec","publisher":"manufacturer","name":"Holosun EU shop","url":"https://www.holosun.eu/en/p/70183184","retrieved":"2026-09-30","via":"harvest"}}],"adopt":{"from":"spec","reason":"Manufacturer product page; the EU listing agrees."}},"height":{"label":"Height (on the 1.63 in mount, presumed)","kind":"length","measurements":[{"id":"spec","value":2.63,"unit":"in","stated":"2.48\" × 1.54\" × 2.63\"","source":{"type":"spec","publisher":"manufacturer","name":"holosun.com ARO-CORE-RD-2 page","url":"https://www.holosun.com/products/aro-core-rd-2","retrieved":"2026-09-30","via":"harvest"},"note":"Holosun doesn't say whether this includes the mount. It's taller than the 1.63 in axis plus half the housing, so presumably yes. Check against a calibrated side photo."},{"id":"eu","value":67,"unit":"mm","stated":"63x39x67 mm","source":{"type":"spec","publisher":"manufacturer","name":"Holosun EU shop","url":"https://www.holosun.eu/en/p/70183184","retrieved":"2026-09-30","via":"harvest"}}],"adopt":{"from":"spec","reason":"Manufacturer product page; the EU listing agrees."},"note":"From the bottom of the mount's rail clamp to the housing top (the battery cap), like the HM3X drawing's 2.42. Holosun's own side view (M3): the top is 2.43 in above the rail top and the clamp reaches 0.23 in below it, 2.66 in all (the photo's two published scales agree within 2%). 2026-10-13: that photo is taken from 20 degrees above, which is where the 2% is from; read from where its lens stood the top is 2.41 over the rail and the clamp's bottom 0.21 to 0.24 under it."},"top_above_rail":{"label":"Housing top above the rail top (on the 1.63 in mount)","kind":"length","measurements":[{"id":"photo","value":2.33,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/holosun-aro dc9df64e16d6 (Sniper Country review, right side on a Picatinny rail; supplied in chat)","scaleRef":"the housing's own length, 2.48 in (holosun-aro.length) = 552 px, i.e. 222.6 px/in in the optic's plane. The rail slots read ~6% smaller (206 px/in) because they're ~0.6 in farther from this close camera.","method":"housing top 155 px above the objective tube's center (the optical axis), + the axis's published 1.63 in","via":"user"}},{"id":"eu-side","value":2.41,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{.optical_axis_above_rail} + {.top_above_axis}","via":"harvest"},"note":"Holosun's EU side photos, both, through the cameras fitted to them (2026-10-13): the elevation cap's top 0.78 in above the optical axis. It was 2.428 while the left photo was read as a square view."}],"adopt":{"from":"eu-side","reason":"Holosun's two product shots, each read from where its lens stood, and consistent with the published 2.63 in overall height (2.41 + 0.23 = 2.64). The review photo (the same optic, a close phone shot) reads 2.33 and stays a visible conflict."}},"tube_od":{"label":"Objective tube outside diameter","kind":"length","measurements":[{"id":"photo","value":1.03,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/holosun-aro dc9df64e16d6 (Sniper Country review, right side on a Picatinny rail; supplied in chat)","scaleRef":"the housing's own length, 2.48 in (holosun-aro.length) = 552 px, i.e. 222.6 px/in in the optic's plane. The rail slots read ~6% smaller (206 px/in) because they're ~0.6 in farther from this close camera.","method":"objective tube's vertical extent at its front end, 230 px (a cylinder's diameter doesn't foreshorten in a side view)","via":"user"}},{"id":"eu-side","value":1.131,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU true side view, ARO on its 1.63 in mount (objective to the left))","scaleRef":"scale from holosun-aro.length = 2.48 in (x-extent 1268 px → 511.3 px/in) and holosun-aro.height = 2.63 in (y-extent 1371 px → 521.3 px/in), which agree within 2.0%; mean 516.3 px/in","method":"height (tooth tops, max over 0.05 in windows) along x [0.1, 0.3] of the traced outline (tools/trace.py); the objective ring's top to bottom, 0.1–0.3 in behind its front","via":"harvest"}},{"id":"eu-camera","value":1.17,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"both photos' fitted cameras (this file's note): 495.7 and 486.0 px/in where they look, each lens 24 in off and 20 degrees up; scales from .length, heights from the tube's centre line","method":"the tube's two edges down column 520 of the left photo (572.5 and 1156.5: 584 px) and column 1640 of the right (554.5 and 1127.5: 573 px), each over the scale where the tube's centre line is seen (0.5849 and 0.5848 in of radius); ± is the camera's distance (1.165 from 30 in, 1.143 from a camera square on) and a pixel at each edge","via":"harvest"},"note":"The same edges as eu-side, at the camera's scale. eu-side took the mean of the scale along the sight (511.3 px/in by .length) and the scale up it (521.3 by .height), and the second is what a view from above does to heights, not a scale."}],"adopt":{"from":"eu-camera","reason":"The same two edges of the same photo, and the other side's, at the scale the published length gives a camera fitted to where the lens stood (2026-10-13): eu-side's 1.131 has the photo's vertical extent in its scale, which a view from 20 degrees above stretches. Holosun's front photo has the 22 mm glass 0.751 of the bezel across (1.153 in if the glass stood at the rim; it stands behind it). The review photo's close phone shot reads 1.03 and stays a visible conflict."}},"mount_length":{"label":"Mount clamp length along the rail","kind":"length","measurements":[{"id":"photo","value":1.81,"unit":"in","pm":0.09,"source":{"type":"photo","photo":"references/holosun-aro dc9df64e16d6 (Sniper Country review; supplied in chat)","scaleRef":"rail slot pitch 0.394 in (std.picatinny.slot_pitch): 84.0 px/slot behind the mount, 79 px in front, interpolated to ~206 px/in at the clamp","method":"clamp silhouette along the rail, 373 px","via":"user"}},{"id":"eu-side","value":1.441,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU true side view, ARO on its 1.63 in mount (objective to the left))","scaleRef":"scale from holosun-aro.length = 2.48 in (x-extent 1268 px → 511.3 px/in) and holosun-aro.height = 2.63 in (y-extent 1371 px → 521.3 px/in), which agree within 2.0%; mean 516.3 px/in","method":"median row width in y [0.05, 0.3] (1.439–1.443) of the traced outline (tools/trace.py); the mount clamp's length along the rail: median row width over its lower 0.05–0.3 in (below the pedestal)","via":"harvest"}},{"id":"eu-camera","value":1.486,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"both side photos' fitted cameras (this file's note): 495.7 and 486.0 px/in where they look, each lens 24 in off and 20 degrees up; scales from .length, heights from the tube's centre line","method":"the clamp's two ends on the jaw's face nearest each lens: columns 760 and 1503.3 of the left photo on the left jaw's face (z -0.563: x 0.756 and -0.735, 1.491) and columns 708.5 and 1435 of the right photo on the right jaw's (z 0.641: x -0.723 and 0.759, 1.482); their middles 0.011 and 0.018, the cross bolt's 0.01","via":"harvest"}}],"adopt":{"from":"eu-camera","reason":"The clamp's two ends read on the jaw's face nearest each lens through that photo's fitted camera, in both side photos (2026-10-13): 1.491 and 1.482. eu-side's 1.441 is the same left photo's outline at one scale for the whole picture (516.3 px/in, the mean of what its length and its height give, the second of them stretched by the view from above), where that photo's camera has 498.7 px/in at the jaw's face; it stays, and so does the review photo's 1.81 (25% longer: it may include the nut, or read the rail's perspective)."}},"optical_axis_above_rail":{"label":"Optical axis above rail top (lower-1/3 mount)","kind":"length","measurements":[{"id":"spec","value":1.63,"unit":"in","stated":"Central Mount Height 1.63\"","source":{"type":"spec","publisher":"manufacturer","name":"holosun.com ARO-CORE-RD-2 page","url":"https://www.holosun.com/products/aro-core-rd-2","retrieved":"2026-09-30","via":"harvest"}},{"id":"manual","value":1.63,"unit":"in","stated":"an all-new 1.63\" lower 1/3 co-witness pedestal mount","source":{"type":"spec","publisher":"manufacturer","name":"Holosun ARO manual","url":"https://cdn.prod.website-files.com/68f92fcb2648b8aa5dc55d79/69607cd520c4134d7e73df07_holosun-aro-core-gd-2-manual.pdf","retrieved":"2026-09-30","via":"harvest"}}],"adopt":{"from":"spec","reason":"Manufacturer; the page and manual agree."}},"low_mount_axis_above_rail":{"label":"Optical axis above rail top (included low mount)","kind":"length","measurements":[{"id":"spec","value":1.05,"unit":"in","stated":"Low Mount Height 1.05\"","source":{"type":"spec","publisher":"manufacturer","name":"holosun.com ARO-CORE-RD-2 page","url":"https://www.holosun.com/products/aro-core-rd-2","retrieved":"2026-09-30","via":"harvest"}}]},"window":{"label":"Window diameter","kind":"length","measurements":[{"id":"brief","value":22,"unit":"mm","source":{"type":"spec","publisher":"manufacturer","name":"Holosun","via":"brief"},"note":"Holosun calls this a 22 mm housing."},{"id":"page","value":0.866,"unit":"in","stated":"0.866 Diameter","source":{"type":"spec","publisher":"manufacturer","name":"holosun.com ARO-CORE-RD-2 page","url":"https://www.holosun.com/products/aro-core-rd-2","retrieved":"2026-09-30","via":"harvest"}},{"id":"manual","value":0.78,"unit":"in","stated":"Window Size: 0.78inches.","source":{"type":"spec","publisher":"manufacturer","name":"Holosun ARO manual","url":"https://cdn.prod.website-files.com/68f92fcb2648b8aa5dc55d79/69607cd520c4134d7e73df07_holosun-aro-core-gd-2-manual.pdf","retrieved":"2026-09-30","via":"harvest"},"note":"May be the clear aperture rather than the housing window."},{"id":"front-photo","value":0.85,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/holosun-aro badfb3ddb2a6 (Holosun's front view, the objective toward the camera, from a little above, 2200 px)","scaleRef":"the objective bezel's outside diameter on the same row (1049), 574 px, as .tube_od (1.131 in): 508 px/in","method":"the red glass at its widest row: 431 px, 0.751 of the bezel. The glass sits down the bezel, further from the lens than the rim that scales it, so it reads small if anything; ± covers tube_od's ±, the glass's edge and that depth","via":"harvest"}}],"adopt":{"from":"page","reason":"Current product page; equals the 22 mm housing. The manual's 0.78 in may be a different definition."},"note":"The objective's glass, which the model draws at the front (2026-10-05; until then both ends were drawn at .window_d, the 0.737 in read from behind, and the front lens was 14% small). The page says which glass: \"22mm Optical Window\", \"Refined 22mm objective\", \"Window Size 0.866 Diameter\"; Holosun's front photo reads 0.85."},"weight_body":{"label":"Weight, optic without mount","kind":"mass","measurements":[{"id":"spec","value":3.38,"unit":"oz","stated":"Body (oz) Weight 3.38 oz","source":{"type":"spec","publisher":"manufacturer","name":"holosun.com ARO-CORE-RD-2 page","url":"https://www.holosun.com/products/aro-core-rd-2","retrieved":"2026-09-30","via":"harvest"}},{"id":"eu","value":101,"unit":"g","source":{"type":"spec","publisher":"manufacturer","name":"Holosun EU shop","url":"https://www.holosun.eu/en/p/70183184","retrieved":"2026-09-30","via":"harvest"},"note":"Unclear whether this includes a mount."}],"adopt":{"from":"spec","reason":"Manufacturer product page."}},"mount_weight":{"label":"Weight, lower-1/3 mount","kind":"mass","measurements":[{"id":"spec","value":1.73,"unit":"oz","stated":"Mount Weight 1.73 oz","source":{"type":"spec","publisher":"manufacturer","name":"holosun.com ARO-CORE-RD-2 page","url":"https://www.holosun.com/products/aro-core-rd-2","retrieved":"2026-09-30","via":"harvest"}}],"note":"Holosun's US page gives one mount weight beside its two mounts (\"Included Mounts 1.63\" Mount 1.05\" Mount\"), and calls the 1.63 in one its \"Central Mount\": taken to be that one's. The mount is a part of its own since 2026-11-05 (holosun-aro-163-mount.weight), where Holosun's EU shop's figure for it sold alone stands beside this one."},"weight":{"label":"Weight, optic on its lower-1/3 mount","kind":"mass","measurements":[{"id":"derived","value":5.11,"unit":"oz","source":{"type":"derived","expr":"{.weight_body} + {.mount_weight}","via":"harvest"}}]},"axis_above_base":{"label":"Optical axis above the sight's own base (its mounting surface, the plane its footprint meets a mount's deck in: D101)","kind":"length","measurements":[{"id":"holosun-rep","value":0.9,"unit":"in","stated":"ARO is .9 in","source":{"type":"spec","publisher":"manufacturer","name":"Holosun (u/Holosun_Josh, answering 'ARO-EVO base to centerline measurement' on r/HOLOSUN; screenshot references/holosun-aro 186034e0c2a2)","via":"user"},"note":"The thread's own example drawing is another optic (1.02 / 1.49 / 1.63 in); only this reply is the ARO's. He quotes the ARO-EVO (the solar model) separately at 0.8 in, so his ARO is this one."},{"id":"eu-side","value":0.967,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU true side view, ARO on its 1.63 in mount (objective to the left))","scaleRef":"scale from holosun-aro.length = 2.48 in (x-extent 1268 px → 511.3 px/in) and holosun-aro.height = 2.63 in (y-extent 1371 px → 521.3 px/in), which agree within 2.0%; mean 516.3 px/in","method":"(centre between the top (max over 0.05 in windows) along x [0.1, 0.3]) − (y_min in x [0.6, 0.82] in y [0.8, 1.5]) of the traced outline (tools/trace.py); the objective ring's centre (0.1–0.3 in behind its front) above the body's underside where it overhangs the pedestal (0.6–0.82 in back)","via":"harvest"}},{"id":"eu-camera","value":0.902,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"both photos' fitted cameras (this file's note): 495.7 and 486.0 px/in where they look, each lens 24 in off and 20 degrees up; scales from .length, heights from the tube's centre line","method":"the skirt's lower edge, which is the bottom of its chamfer (skirt_bottom_width apart; taken 0.443 in off the middle plane toward the lens): rows 1365 and 1367 down columns 800 and 1450 of the left photo (0.726 and 0.722 in over the rail) and rows 1335 and 1332 down columns 720 and 1420 of the right (0.735 and 0.731); their mean 0.728 under the axis's 1.63 (0.730, and this figure 0.900, with the edge 0.447 off the middle plane as the refitted rear view has it). ± is the edge's distance from the middle plane (0.38 of it), the camera's angle and the picks","via":"harvest"},"note":"eu-side is the same edge read as a square view: from 20 degrees above, an edge 0.44 in nearer the lens stands 0.11 in lower against the tube's centre line, less what the foreshortening takes off 0.9 in (0.05)."}],"adopt":{"from":"eu-camera","reason":"Holosun's own .9 in, within a hundredth, once the photo is read from where its lens stood (2026-10-13): eu-side's 0.967 is the skirt's near edge read as if it lay in the middle plane. It stays beside it."},"note":"Called base_to_axis until 2026-11-05, when the 1.63 in mount became a part of its own (D101): what the sight brings to any Micro-footprint mount, its axis this far over the deck it is screwed to. On its own pedestal it puts the axis at Holosun's 1.63 in, which is what the pedestal's deck height is worked out from (holosun-aro-163-mount.deck_above_rail)."},"top_above_axis":{"label":"Housing top (battery cap) above the optical axis","kind":"length","measurements":[{"id":"eu-side","value":0.798,"unit":"in","pm":0.032,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU true side view, ARO on its 1.63 in mount (objective to the left))","scaleRef":"scale from holosun-aro.length = 2.48 in (x-extent 1268 px → 511.3 px/in) and holosun-aro.height = 2.63 in (y-extent 1371 px → 521.3 px/in), which agree within 2.0%; mean 516.3 px/in","method":"(y_max) − (centre between the top (max over 0.05 in windows) along x [0.1, 0.3]) of the traced outline (tools/trace.py); the housing's highest point (the battery cap) above the objective ring's centre","via":"harvest"}},{"id":"eu-camera","value":0.78,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"both photos' fitted cameras (this file's note): 495.7 and 486.0 px/in where they look, each lens 24 in off and 20 degrees up; scales from .length, heights from the tube's centre line","method":"the elevation cap's centre seen in both photos (left 1427.3, 494.5: the middle of its two dots and of its rings; right 772.3, 481.5): the two lines of sight pass 0.006 in apart at x -0.571, y 2.406, z -0.011, on the cap's inner disc; its top face is 0.004 over that (the photo's top, row 453 at column 1428, is the far rim of a face 0.267 in in radius at 2.41)","via":"harvest"},"note":"eu-side is the photo's top row read as a square view: the far rim of the cap's top face, which a camera 20 degrees above sees 0.09 in higher than a point of the middle plane at that height, less the foreshortening of 0.78 in (0.05)."}],"adopt":{"from":"eu-camera","reason":"Seen from both sides, where the two lines of sight meet (2026-10-13); eu-side read one photo's top row as a square view. With clamp_below_rail the height comes to 2.64 in for Holosun's 2.63."}},"axis_above_clamp_bottom":{"label":"Optical axis above the mount clamp's bottom (on the 1.63 in mount)","kind":"length","measurements":[{"id":"eu-side","value":1.857,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU true side view, ARO on its 1.63 in mount (objective to the left))","scaleRef":"scale from holosun-aro.length = 2.48 in (x-extent 1268 px → 511.3 px/in) and holosun-aro.height = 2.63 in (y-extent 1371 px → 521.3 px/in), which agree within 2.0%; mean 516.3 px/in","method":"centre between the top (max over 0.05 in windows) along x [0.1, 0.3] of the traced outline (tools/trace.py); the objective ring's centre above the mount clamp's bottom (the origin)","via":"harvest"}}]},"mount_rise":{"label":"Optic base above the rail top (on the 1.63 in mount)","kind":"length","measurements":[{"id":"derived","value":0.728,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.optical_axis_above_rail} - {.axis_above_base}","via":"harvest"},"note":"Holosun's 1.63 in less the base-to-axis height: how far the pedestal lifts the optic (0.73 with Holosun's rounded .9). 0.663 until 2026-10-13, while the base's edge was read as a square view."}]},"clamp_below_rail":{"label":"Mount clamp's bottom below the rail top","kind":"length","measurements":[{"id":"derived","value":0.227,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.axis_above_clamp_bottom} - {.optical_axis_above_rail}","via":"harvest"},"note":"The jaws wrap the rail's sides; the HM3X's reach 0.22 in."}]},"clamp_bottom_y":{"label":"Mount clamp's bottom in the optic frame (y, the rail top is 0)","kind":"length","measurements":[{"id":"derived","value":-0.227,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"-{.clamp_below_rail}","via":"harvest"},"note":"Where the side profile's clamp-bottom origin sits in the part frame."}]},"window_d":{"label":"Window (lens) diameter, clear, seen from the rear","kind":"length","measurements":[{"id":"end-user","value":0.737,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-aro 33a02158eb43 (ARO-RD2 end view from the rear, on white; supplied in chat)","scaleRef":"the end view's least-squares frame on the vertical layout (136.6 px/in, rms 0.042 in)","method":"the window's edge (white to dark) on radial profiles from the axis, radius 50.3 ± 1 px; ± covers the edge and the frame's scale","via":"user"}}],"note":"Draws the rear window (M5): the clear circle the backdrop shows through in the user's end view from the rear, round in every direction (edge radius 50–51 px at 0°, 90°, 180°, 270°). The objective's glass at the front is larger and has its own figure (.window)."},"eyepiece_od":{"label":"Eyepiece bezel outside diameter","kind":"length","measurements":[{"id":"eu-camera","value":1.094,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"both side photos' fitted cameras (this file's note): 495.7 and 486.0 px/in where they look, each lens 24 in off and 20 degrees up; scales from .length, heights from the tube's centre line","method":"the bezel's two edges down column 1688 of the left photo (590.5 and 1136.5) and column 520 of the right (581 and 1117.5), over the scale where its centre line is seen: 0.547 and 0.548 in of radius; ± as tube_od's","via":"harvest"}}]},"barrel_od":{"label":"Housing: the round body between the two bezels, diameter","kind":"length","measurements":[{"id":"end-user","value":1.2,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-aro 33a02158eb43 (ARO-RD2 end view from the rear, on white; supplied in chat)","scaleRef":"the end view's frame as profiles.front has it (135.4 px/in, rms 0.013 in over its five heights, 1.537 in across for Holosun's 1.54), its middle taken 0.018 in right of the window's centre, where the skirt, the mount's stem and the clamp's jaws have theirs","method":"the outline's left side from 0.37 in under the axis to 0.47 over it lies on one circle about the axis: 0.596 to 0.605 in from it at seven of the traced outline's points (profiles.front); ± is the frame's scale (2.5%) and the picks","via":"user"}}],"note":"A straight view along the sight shows whichever is widest, and the objective's bezel (tube_od, 1.17) is within a hundredth of it: the two can't be told apart there. That the body is the larger is seen where the tube leaves it (the housing's front face shows as a ring round the tube in d968cfc95219 and 5ec56fffa262, looked at, not measured). Holosun's rear photo from above has the body 4.5% wider than the eyepiece's bezel just behind it (1.14 in before the 0.2 to 0.3 in between them is allowed for). The readings taken on the round body below were taken on a round of 1.19 in, as this read before the rear view's frame was refitted; at 1.20 none of them moves by 0.005."},"rear_behind_clamp_middle":{"label":"Eyepiece's rear face behind the clamp's middle (the frame's origin)","kind":"length","measurements":[{"id":"eu-side","value":1.115,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"the left photo's fitted camera (this file's note): 495.7 px/in at the point it looks at, the lens 24 in off and 20 degrees up; its scale from .length, its height from the tube's centre line","method":"the silhouette's rear end (column 1707.5 at the axis's row) against the middle of the clamp's two ends (columns 761.6 and 1503.0): 1.117 in the traced outline; the camera is fitted with the rear end at this figure, and then sees the clamp's middle 0.009 in ahead of the origin on the near jaw's face. ± is that and the clamp's ends","via":"harvest"}}],"note":"Where the housing stands along the mount. The front end is .length ahead of it."},"housing_front_x":{"label":"Housing: its front face, where the objective's tube leaves it, X","kind":"length","measurements":[{"id":"eu-camera","value":1.055,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"both side photos' fitted cameras (this file's note): 495.7 and 486.0 px/in where they look, each lens 24 in off and 20 degrees up; scales from .length, heights from the tube's centre line","method":"the step from the tube to the body along the left photo's row 850 (column 599: 1.053) and the right's row 700 (column 1587: 1.058), each on the round body (barrel_od)","via":"harvest"}}]},"housing_rear_x":{"label":"Housing: its rear face, where the eyepiece's bezel leaves it, X","kind":"length","measurements":[{"id":"eu-camera","value":-1.028,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"both side photos' fitted cameras (this file's note): 495.7 and 486.0 px/in where they look, each lens 24 in off and 20 degrees up; scales from .length, heights from the tube's centre line","method":"the step from the body to the bezel along row 850 of each photo (left column 1664, right column 539: -1.028 both), on the round body","via":"harvest"}}]},"skirt_width":{"label":"Housing: the block under the round body, across its flat flanks","kind":"length","measurements":[{"id":"end-user","value":1.094,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/holosun-aro 33a02158eb43 (ARO-RD2 end view from the rear, on white; supplied in chat)","scaleRef":"the end view's frame as profiles.front has it (135.4 px/in, rms 0.013 in over its five heights, 1.537 in across for Holosun's 1.54), z counted from the window's centre as that outline counts it (the mount is drawn from that outline)","method":"the outline's two upright stretches under the round body: z -0.530 on the left (y 0.79 to 1.20) and +0.564 on the right, under the battery tray's cover (y 0.81 to 0.96); ± is the frame's scale and a pixel each side (0.007)","via":"user"}}],"note":"The flanks are flat and upright (the rear view's outline is straight there over 0.4 in). The left flank has a raised panel on it in Holosun's left photo that isn't drawn; if it stands out of the flank, the flank itself is that much narrower."},"skirt_bottom_width":{"label":"Housing: its underside, across (inside the flanks' lower chamfers)","kind":"length","measurements":[{"id":"end-user","value":0.894,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/holosun-aro 33a02158eb43 (ARO-RD2 end view from the rear, on white; supplied in chat)","scaleRef":"the end view's frame as profiles.front has it (135.4 px/in, rms 0.013 in over its five heights, 1.537 in across for Holosun's 1.54), z counted from the window's centre as that outline counts it (the mount is drawn from that outline)","method":"the outline's two lower corners, where the chamfers end on the underside: z -0.430 and +0.464; ± as skirt_width's","via":"user"}}]},"skirt_chamfer_top_y":{"label":"Housing: where a flank's lower chamfer begins, above the rail","kind":"length","measurements":[{"id":"eu-camera","value":0.89,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"both side photos' fitted cameras (this file's note): 495.7 and 486.0 px/in where they look, each lens 24 in off and 20 degrees up; scales from .length, heights from the tube's centre line","method":"the fine dark line along each flank: row 1303 down column 970 of the left photo (0.896, on the flank's plane, skirt_width) and row 1283 down column 1100 of the right (0.880)","via":"harvest"}}]},"skirt_top_y":{"label":"Housing: the top of a flat flank, above the rail","kind":"length","measurements":[{"id":"eu-camera","value":1.22,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"the left photo's fitted camera (this file's note): 495.7 px/in at the point it looks at, the lens 24 in off and 20 degrees up; its scale from .length, its height from the tube's centre line","method":"the flank's upper edge down column 970: rows 1135 to 1160 (1.251 to 1.198 on the flank's plane), taken at 1150; the rear view's outline has the flank upright to 1.20 and a notch at 1.26. ± is which of the lines there is the edge","via":"harvest"}}]},"skirt_shoulder_y":{"label":"Housing: where the flank's shoulder meets the round body, above the rail","kind":"length","measurements":[{"id":"eu-camera","value":1.3,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"the left photo's fitted camera (this file's note): 495.7 px/in at the point it looks at, the lens 24 in off and 20 degrees up; its scale from .length, its height from the tube's centre line","method":"the lit line over the flank down column 970, row 1104, met with the round body (barrel_od): y 1.298, 0.494 in off the middle plane","via":"harvest"}}],"note":"Between the flank's top (skirt_top_y) and this the model has one flat shoulder; the photo has two or three lines there (a bead, by the look), which aren't read."},"skirt_bottom_front_x":{"label":"Housing: its underside's front end, X","kind":"length","measurements":[{"id":"eu-camera","value":0.806,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"the left photo's fitted camera (this file's note): 495.7 px/in at the point it looks at, the lens 24 in off and 20 degrees up; its scale from .length, its height from the tube's centre line","method":"the silhouette's lower front corner (column 733, row 1365) on the underside's near edge (skirt_bottom_width); from there the front end slants up to the housing's front face at the flank's top","via":"harvest"}}]},"skirt_bottom_rear_x":{"label":"Housing: its underside's rear end, X","kind":"length","measurements":[{"id":"eu-camera","value":-0.771,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"the left photo's fitted camera (this file's note): 495.7 px/in at the point it looks at, the lens 24 in off and 20 degrees up; its scale from .length, its height from the tube's centre line","method":"the silhouette's lower rear corner (column 1524, row 1366) on the underside's near edge; from there the rear end slants up to the housing's rear face at the flank's top","via":"harvest"}}]},"deck_top_width":{"label":"Housing: the raised deck along its top, across its top","kind":"length","measurements":[{"id":"end-user","value":0.65,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-aro 33a02158eb43 (ARO-RD2 end view from the rear, on white; supplied in chat)","scaleRef":"the end view's frame as profiles.front has it (135.4 px/in, rms 0.013 in over its five heights, 1.537 in across for Holosun's 1.54), its middle taken 0.018 in right of the window's centre, where the skirt, the mount's stem and the clamp's jaws have theirs","method":"the top block's upper corners in the outline: z -0.330 and +0.320","via":"user"}}],"note":"Holosun's left photo sees the deck's top from 17 degrees above, 93 px from its far edge to its near one down column 970: 0.63 in across if the two edges are level with one another."},"deck_foot_width":{"label":"Housing: the raised deck, across its foot on the round body","kind":"length","measurements":[{"id":"end-user","value":0.739,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-aro 33a02158eb43 (ARO-RD2 end view from the rear, on white; supplied in chat)","scaleRef":"the end view's frame as profiles.front has it (135.4 px/in, rms 0.013 in over its five heights, 1.537 in across for Holosun's 1.54), its middle taken 0.018 in right of the window's centre, where the skirt, the mount's stem and the clamp's jaws have theirs","method":"where the top block's sides meet the circle in the outline: z -0.375 and +0.364, at y 2.105 and 2.12","via":"user"}}]},"deck_front_x":{"label":"Housing: the deck's front top edge, X","kind":"length","measurements":[{"id":"eu-camera","value":0.977,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"the left photo's fitted camera (this file's note): 495.7 px/in at the point it looks at, the lens 24 in off and 20 degrees up; its scale from .length, its height from the tube's centre line","method":"the housing's front top corner (column 650, row 507) at the deck's own height there","via":"harvest"}}]},"deck_top_front_y":{"label":"Housing: the deck's top at its front edge, above the rail","kind":"length","measurements":[{"id":"eu-camera","value":2.29,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"both side photos' fitted cameras (this file's note): 495.7 and 486.0 px/in where they look, each lens 24 in off and 20 degrees up; scales from .length, heights from the tube's centre line","method":"the line through the two buttons' centres, each seen in both photos (plus: left 831, 538 and right 1356.5, 524.5, lines of sight 0.004 in apart at x 0.610, y 2.311; minus: left 1105.5, 524.5 and right 1089.5, 511.5, 0.009 apart at x 0.068, y 2.341), carried to deck_front_x: 2.291. The front top corner's own row (507) is that height there","via":"harvest"}}],"note":"The deck rises to the rear at 3.2 degrees."},"deck_top_rear_y":{"label":"Housing: the deck's top under the elevation cap, above the rail","kind":"length","measurements":[{"id":"eu-camera","value":2.376,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"both side photos' fitted cameras (this file's note): 495.7 and 486.0 px/in where they look, each lens 24 in off and 20 degrees up; scales from .length, heights from the tube's centre line","method":"the same line through the two buttons' centres (deck_top_front_y), carried back to turret_x","via":"harvest"}}],"note":"The cap's top (top_above_axis) is 0.034 over it. Behind the cap the deck ends in a face that slopes down to the round body's rear top edge (the silhouette, rows 478 to 587 over columns 1597 to 1653 of the left photo): drawn from the cap's boss to that edge, with no reading of its own."},"pad_front_x":{"label":"Button pad: its front end, X","kind":"length","measurements":[{"id":"eu-camera","value":0.89,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"both side photos' fitted cameras (this file's note): 495.7 and 486.0 px/in where they look, each lens 24 in off and 20 degrees up; scales from .length, heights from the tube's centre line","method":"the dark line across the deck ahead of the plus button, on the deck's top: column 683 of the left photo (0.900) and column 1487 of the right (0.878)","via":"harvest"}}]},"pad_rear_x":{"label":"Button pad: its rear end, X","kind":"length","measurements":[{"id":"eu-camera","value":-0.23,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"both side photos' fitted cameras (this file's note): 495.7 and 486.0 px/in where they look, each lens 24 in off and 20 degrees up; scales from .length, heights from the tube's centre line","method":"the dark line across the deck between the minus button and the cap: column 1252 of the left photo (-0.227) and column 938 of the right (-0.234)","via":"harvest"}}]},"pad_width":{"label":"Button pad: across","kind":"length","measurements":[{"id":"eu-rear","value":0.55,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/holosun-aro fff751cd35fa (Holosun EU, from behind and about 30 degrees above; 2200 px)","scaleRef":"the minus button beside it on the same row, 192 px across (columns 948 to 1140) for button_d","method":"the pad's face inside its border, columns 885 to 1180 on the minus button's row: 1.54 buttons across. ± is the edges (5 px each) and button_d's","via":"harvest"}}],"note":"Holosun's left photo has the pad's far and near edges 81 px apart down column 970, seen from 17 degrees above: 0.55 in."},"pad_proud":{"label":"Button pad: how far it stands over the deck's rim","kind":"length","measurements":[{"id":"eu-camera","value":0.012,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"the left photo's fitted camera (this file's note): 495.7 px/in at the point it looks at, the lens 24 in off and 20 degrees up; its scale from .length, its height from the tube's centre line","method":"down column 970 the pad's near edge is at row 571 and the deck's near edge at 583: 12 px, of which the rim beside the pad (half of deck_top_width less pad_width) takes 7 seen from 17 degrees above; the 5 left are the pad's own edge","via":"harvest"}}],"note":"Under the 0.02 in the page draws: it is what parts the pad from the deck."},"button_d":{"label":"Button: diameter","kind":"length","measurements":[{"id":"eu-camera","value":0.357,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"the left photo's fitted camera (this file's note): 495.7 px/in at the point it looks at, the lens 24 in off and 20 degrees up; its scale from .length, its height from the tube's centre line","method":"each button's dark ring along the sight, fitted as an ellipse (the plus 181.2 px long, the minus 179.0), on the pad's top at its own height: 0.360 and 0.354","via":"harvest"}}]},"button_plus_x":{"label":"Plus button (the front one): centre, X","kind":"length","measurements":[{"id":"eu-camera","value":0.61,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"both side photos' fitted cameras (this file's note): 495.7 and 486.0 px/in where they look, each lens 24 in off and 20 degrees up; scales from .length, heights from the tube's centre line","method":"the cross's centre in both photos (left 831, 538; right 1356.5, 524.5): lines of sight 0.004 in apart at x 0.610, y 2.311, z 0.006","via":"harvest"}}]},"button_minus_x":{"label":"Minus button: centre, X","kind":"length","measurements":[{"id":"eu-camera","value":0.068,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"both side photos' fitted cameras (this file's note): 495.7 and 486.0 px/in where they look, each lens 24 in off and 20 degrees up; scales from .length, heights from the tube's centre line","method":"the bar's centre in both photos (left 1105.5, 524.5; right 1089.5, 511.5): lines of sight 0.009 in apart at x 0.068, y 2.341, z -0.001","via":"harvest"}}]},"button_ring_width":{"label":"Button: the groove round it, across","kind":"length","measurements":[{"id":"eu-camera","value":0.02,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"the left photo's fitted camera (this file's note): 495.7 px/in at the point it looks at, the lens 24 in off and 20 degrees up; its scale from .length, its height from the tube's centre line","method":"the dark crescent at each button's two ends along the sight, 8 to 10 px","via":"harvest"}}],"note":"How deep it is isn't seen: drawn detail_relief deep."},"button_mark_length":{"label":"Button: its raised mark (the minus bar, and each arm of the plus), length","kind":"length","measurements":[{"id":"eu-camera","value":0.23,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"the left photo's fitted camera (this file's note): 495.7 px/in at the point it looks at, the lens 24 in off and 20 degrees up; its scale from .length, its height from the tube's centre line","method":"the minus bar's two ends along row 524.5 (columns 1048 and 1163) on the pad's top: x 0.177 and -0.051","via":"harvest"}}]},"button_mark_width":{"label":"Button: its raised mark, across","kind":"length","measurements":[{"id":"eu-camera","value":0.044,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"the left photo's fitted camera (this file's note): 495.7 px/in at the point it looks at, the lens 24 in off and 20 degrees up; its scale from .length, its height from the tube's centre line","method":"the plus's arm that points at the lens, across the sight: columns 820 to 842 on the pad's top","via":"harvest"}}],"note":"How far the marks stand isn't seen: drawn at pad_proud."},"turret_x":{"label":"The two turrets: their common station, X","kind":"length","measurements":[{"id":"eu-camera","value":-0.57,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"both side photos' fitted cameras (this file's note): 495.7 and 486.0 px/in where they look, each lens 24 in off and 20 degrees up; scales from .length, heights from the tube's centre line","method":"the elevation cap's centre seen in both photos (top_above_axis: x -0.571) and the windage cap's rings in the right photo (an ellipse about 770.1, 973.8 on its face's plane, windage_cap_reach_z: x -0.566)","via":"harvest"}}]},"cap_d":{"label":"Turret cap: diameter (both caps)","kind":"length","measurements":[{"id":"eu-camera","value":0.534,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"both side photos' fitted cameras (this file's note): 495.7 and 486.0 px/in where they look, each lens 24 in off and 20 degrees up; scales from .length, heights from the tube's centre line","method":"the elevation cap's top face along the sight in the left photo (columns 1292 to 1562 at its own height: radius 0.267) and the windage cap's face in the right (269 px across on its plane: 0.266). The ring cut in each, further in, is 0.241 and 0.240 in in radius","via":"harvest"}}],"note":"The two caps are one part: their rings agree to a thousandth once each is at its own distance from the lens."},"cap_slot_length":{"label":"Turret cap: its coin slot, length","kind":"length","measurements":[{"id":"eu-camera","value":0.24,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 6d33513e41f7 (Holosun EU, the right side, taken from 20 degrees above; 2200 px)","scaleRef":"the right photo's fitted camera (this file's note): 486.0 px/in at the point it looks at, the lens 24 in off and 20 degrees up, the photo rolled 0.42 degrees; its scale from .length, its height from the tube's centre line","method":"the windage cap's slot, end to end (712.7, 990 to 828.6, 952.7) on the cap's face: 0.229 along and 0.078 up","via":"harvest"}}]},"cap_slot_width":{"label":"Turret cap: its coin slot, across","kind":"length","measurements":[{"id":"eu-camera","value":0.04,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/holosun-aro 6d33513e41f7 (Holosun EU, the right side, taken from 20 degrees above; 2200 px)","scaleRef":"the right photo's fitted camera (this file's note): 486.0 px/in at the point it looks at, the lens 24 in off and 20 degrees up, the photo rolled 0.42 degrees; its scale from .length, its height from the tube's centre line","method":"the windage cap's slot across its middle, about 20 px on the cap's face","via":"harvest"}}],"note":"How deep it is isn't seen: drawn as deep as it is wide."},"windage_y":{"label":"Windage turret: its axis above the rail","kind":"length","measurements":[{"id":"eu-camera","value":1.63,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 6d33513e41f7 (Holosun EU, the right side, taken from 20 degrees above; 2200 px)","scaleRef":"the right photo's fitted camera (this file's note): 486.0 px/in at the point it looks at, the lens 24 in off and 20 degrees up, the photo rolled 0.42 degrees; its scale from .length, its height from the tube's centre line","method":"the cap's two rings, fitted as ellipses about (770.1, 973.8) and (770.1, 975.0), on the cap's face (windage_cap_reach_z): 1.631","via":"harvest"}}],"note":"Level with the optical axis: the rear view has the turret's block about the window's centre too (its outer face from 0.26 in under the axis to 0.28 over it, the whole block 0.64 in tall). Read as a square view the right photo has it 0.25 in under the axis: the cap's face is 0.78 in nearer a lens that stands 20 degrees above."},"windage_cap_reach_z":{"label":"Windage turret: its cap's face from the middle plane","kind":"length","measurements":[{"id":"end-user","value":0.78,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 33a02158eb43 (ARO-RD2 end view from the rear, on white; supplied in chat)","scaleRef":"the end view's frame as profiles.front has it (135.4 px/in, rms 0.013 in over its five heights, 1.537 in across for Holosun's 1.54), its middle taken 0.018 in right of the window's centre, where the skirt, the mount's stem and the clamp's jaws have theirs","method":"the turret's outer face in the outline, z +0.793 to +0.800 from the window's centre","via":"user"}}],"note":"The right photo's camera puts the cap level with the optical axis when its face is 0.777 in out: the same figure by another road."},"windage_boss_reach_z":{"label":"Windage turret: its boss's face (the cap stands on it) from the middle plane","kind":"length","measurements":[{"id":"end-user","value":0.73,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-aro 33a02158eb43 (ARO-RD2 end view from the rear, on white; supplied in chat)","scaleRef":"the end view's frame as profiles.front has it (135.4 px/in, rms 0.013 in over its five heights, 1.537 in across for Holosun's 1.54), its middle taken 0.018 in right of the window's centre, where the skirt, the mount's stem and the clamp's jaws have theirs","method":"the step at the turret's outer corners in the outline: z +0.745 where the corner's cut begins, +0.793 on the face","via":"user"}}],"note":"The cap's corner may be a chamfer and not a step: the cap then stands out of its boss by less than the 0.05 in drawn."},"windage_boss_d":{"label":"Windage turret: its boss, diameter","kind":"length","measurements":[{"id":"eu-camera","value":0.66,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-aro 6d33513e41f7 (Holosun EU, the right side, taken from 20 degrees above; 2200 px)","scaleRef":"the right photo's fitted camera (this file's note): 486.0 px/in at the point it looks at, the lens 24 in off and 20 degrees up, the photo rolled 0.42 degrees; its scale from .length, its height from the tube's centre line","method":"the boss's rim along the sight, columns 602 to 934 at the cap's row, on its own face's plane: radius 0.329","via":"harvest"}}],"note":"The rear view has the turret's block 0.64 in tall (1.325 to 1.968 over the rail in its outline), with a flat rear face and cut corners: the boss may not be a plain cylinder behind. Drawn as one."},"cover_rear_x":{"label":"Battery tray's cover (right flank): its rear end, X","kind":"length","measurements":[{"id":"eu-camera","value":-0.52,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 6d33513e41f7 (Holosun EU, the right side, taken from 20 degrees above; 2200 px)","scaleRef":"the right photo's fitted camera (this file's note): 486.0 px/in at the point it looks at, the lens 24 in off and 20 degrees up, the photo rolled 0.42 degrees; its scale from .length, its height from the tube's centre line","method":"the cover's lit rim at its rear end (column 800, row 1200) on its own face (cover_proud out of the flank)","via":"harvest"}}]},"cover_front_x":{"label":"Battery tray's cover: its front end, X","kind":"length","measurements":[{"id":"eu-camera","value":0.8,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 6d33513e41f7 (Holosun EU, the right side, taken from 20 degrees above; 2200 px)","scaleRef":"the right photo's fitted camera (this file's note): 486.0 px/in at the point it looks at, the lens 24 in off and 20 degrees up, the photo rolled 0.42 degrees; its scale from .length, its height from the tube's centre line","method":"the cover's lit rim at its front end (column 1455, row 1200) on its own face: 0.797","via":"harvest"}}]},"cover_bottom_y":{"label":"Battery tray's cover: its lower edge, above the rail","kind":"length","measurements":[{"id":"eu-camera","value":0.927,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 6d33513e41f7 (Holosun EU, the right side, taken from 20 degrees above; 2200 px)","scaleRef":"the right photo's fitted camera (this file's note): 486.0 px/in at the point it looks at, the lens 24 in off and 20 degrees up, the photo rolled 0.42 degrees; its scale from .length, its height from the tube's centre line","method":"the cover's lower edge at its middle (column 1120, row 1268) on its own face","via":"harvest"}}],"note":"At its middle. Round each screw the edge dips a little lower (the head's own rim is at 0.927): the cover's ends are lobes about the screws, drawn as a rounded rectangle's corners."},"cover_top_y":{"label":"Battery tray's cover: its upper edge, above the rail","kind":"length","measurements":[{"id":"eu-camera","value":1.23,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 6d33513e41f7 (Holosun EU, the right side, taken from 20 degrees above; 2200 px)","scaleRef":"the right photo's fitted camera (this file's note): 486.0 px/in at the point it looks at, the lens 24 in off and 20 degrees up, the photo rolled 0.42 degrees; its scale from .length, its height from the tube's centre line","method":"the cover's upper edge at its middle (column 1120, row 1128) on its own face: 1.228","via":"harvest"}}]},"cover_corner_r":{"label":"Battery tray's cover: the round of its corners","kind":"length","measurements":[{"id":"eu-camera","value":0.13,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-aro 6d33513e41f7 (Holosun EU, the right side, taken from 20 degrees above; 2200 px)","scaleRef":"the right photo's fitted camera (this file's note): 486.0 px/in at the point it looks at, the lens 24 in off and 20 degrees up, the photo rolled 0.42 degrees; its scale from .length, its height from the tube's centre line","method":"the rear end's upper round leaves the upper edge about 0.14 in ahead of the end and the end's upright about as far down; the lower rounds are tighter (about 0.10)","via":"harvest"}}],"note":"One round for the four corners."},"cover_proud":{"label":"Battery tray's cover: how far it stands out of the right flank","kind":"length","measurements":[{"id":"end-user","value":0.035,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 33a02158eb43 (ARO-RD2 end view from the rear, on white; supplied in chat)","scaleRef":"the end view's frame as profiles.front has it (135.4 px/in, rms 0.013 in over its five heights, 1.537 in across for Holosun's 1.54), z counted from the window's centre as that outline counts it (the mount is drawn from that outline)","method":"the outline's right side: the flank at z +0.564 under the cover, the cover at +0.586 to +0.615 over it (0.022 to 0.051)","via":"user"}}]},"cover_screw_rear_x":{"label":"Battery tray's cover: its rear screw, X","kind":"length","measurements":[{"id":"eu-camera","value":-0.352,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/holosun-aro 6d33513e41f7 (Holosun EU, the right side, taken from 20 degrees above; 2200 px)","scaleRef":"the right photo's fitted camera (this file's note): 486.0 px/in at the point it looks at, the lens 24 in off and 20 degrees up, the photo rolled 0.42 degrees; its scale from .length, its height from the tube's centre line","method":"the screw head's middle (883, 1230: its rim's and its socket's) on the cover's face","via":"harvest"}}]},"cover_screw_front_x":{"label":"Battery tray's cover: its front screw, X","kind":"length","measurements":[{"id":"eu-camera","value":0.652,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/holosun-aro 6d33513e41f7 (Holosun EU, the right side, taken from 20 degrees above; 2200 px)","scaleRef":"the right photo's fitted camera (this file's note): 486.0 px/in at the point it looks at, the lens 24 in off and 20 degrees up, the photo rolled 0.42 degrees; its scale from .length, its height from the tube's centre line","method":"the screw head's middle (1383, 1232) on the cover's face","via":"harvest"}}],"note":"The two are 1.00 in apart."},"cover_screw_y":{"label":"Battery tray's cover: its two screws, above the rail","kind":"length","measurements":[{"id":"eu-camera","value":1.01,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 6d33513e41f7 (Holosun EU, the right side, taken from 20 degrees above; 2200 px)","scaleRef":"the right photo's fitted camera (this file's note): 486.0 px/in at the point it looks at, the lens 24 in off and 20 degrees up, the photo rolled 0.42 degrees; its scale from .length, its height from the tube's centre line","method":"the two heads' middles (rows 1230 and 1232) on the cover's face: 1.013 and 1.001; ± is the heads' rims, which a ring fitted to their shadow puts 7 px lower","via":"harvest"}}]},"cover_screw_head_d":{"label":"Battery tray's cover: a screw's head, diameter","kind":"length","measurements":[{"id":"eu-camera","value":0.165,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/holosun-aro 6d33513e41f7 (Holosun EU, the right side, taken from 20 degrees above; 2200 px)","scaleRef":"the right photo's fitted camera (this file's note): 486.0 px/in at the point it looks at, the lens 24 in off and 20 degrees up, the photo rolled 0.42 degrees; its scale from .length, its height from the tube's centre line","method":"each head's rim along the sight (82.2 and 80.8 px) on the cover's face: 0.166 and 0.162","via":"harvest"}}],"note":"Torx heads. Their sockets aren't drawn; how far the heads stand isn't seen (drawn detail_relief)."},"logo_length":{"label":"The HOLOSUN panel on each side: an oval sunk in the round body, length","kind":"length","measurements":[{"id":"eu-camera","value":1.042,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"both side photos' fitted cameras (this file's note): 495.7 and 486.0 px/in where they look, each lens 24 in off and 20 degrees up; scales from .length, heights from the tube's centre line","method":"the oval's two ends on the round body (barrel_od): columns 853 and 1386 along row 950 of the left photo (x 0.557 and -0.485) and columns 982 and 1505 along row 935 of the right (-0.148 and 0.894): 1.042 both","via":"harvest"}}]},"logo_height":{"label":"The HOLOSUN panel: height","kind":"length","measurements":[{"id":"eu-camera","value":0.245,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"both side photos' fitted cameras (this file's note): 495.7 and 486.0 px/in where they look, each lens 24 in off and 20 degrees up; scales from .length, heights from the tube's centre line","method":"the oval's upper and lower edges on the round body: rows 890 and 1012 down column 1120 of the left photo (1.774 and 1.524) and rows 879 and 993 down column 1240 of the right (1.754 and 1.514)","via":"harvest"}}],"note":"Its ends are half rounds. That it is sunk and not raised is read from its shading in the two obliques (d968cfc95219, 5ec56fffa262); how deep isn't seen (drawn detail_relief). The lettering in it isn't drawn."},"logo_mid_y":{"label":"The HOLOSUN panel: its middle above the rail","kind":"length","measurements":[{"id":"eu-camera","value":1.64,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"both side photos' fitted cameras (this file's note): 495.7 and 486.0 px/in where they look, each lens 24 in off and 20 degrees up; scales from .length, heights from the tube's centre line","method":"the middle of the same edges: 1.649 on the left, 1.634 on the right","via":"harvest"}}]},"logo_left_mid_x":{"label":"The HOLOSUN panel on the left side: its middle, X","kind":"length","measurements":[{"id":"eu-camera","value":0.036,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"the left photo's fitted camera (this file's note): 495.7 px/in at the point it looks at, the lens 24 in off and 20 degrees up; its scale from .length, its height from the tube's centre line","method":"the middle of its two ends (x 0.557 and -0.485)","via":"harvest"}}]},"logo_right_mid_x":{"label":"The HOLOSUN panel on the right side: its middle, X","kind":"length","measurements":[{"id":"eu-camera","value":0.373,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/holosun-aro 6d33513e41f7 (Holosun EU, the right side, taken from 20 degrees above; 2200 px)","scaleRef":"the right photo's fitted camera (this file's note): 486.0 px/in at the point it looks at, the lens 24 in off and 20 degrees up, the photo rolled 0.42 degrees; its scale from .length, its height from the tube's centre line","method":"the middle of its two ends (x -0.148 and 0.894)","via":"harvest"}}],"note":"Further forward than the left one: the windage turret has the rear of this side."},"flute_front_x":{"label":"The long flute high on each flank: its front end, X","kind":"length","measurements":[{"id":"eu-camera","value":0.94,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"both side photos' fitted cameras (this file's note): 495.7 and 486.0 px/in where they look, each lens 24 in off and 20 degrees up; scales from .length, heights from the tube's centre line","method":"the flute's front end on the round body: column 657 along row 740 of the left photo (0.941) and column 1526 along row 720 of the right (0.940)","via":"harvest"}}]},"flute_rear_x":{"label":"The long flute: its rear end, X","kind":"length","measurements":[{"id":"eu-camera","value":-0.92,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"the left photo's fitted camera (this file's note): 495.7 px/in at the point it looks at, the lens 24 in off and 20 degrees up; its scale from .length, its height from the tube's centre line","method":"the flute's rear end on the round body: column 1607 along row 740 (-0.918)","via":"harvest"}}],"note":"On the right side the elevation turret's boss and the windage turret's stand in its rear third; it is drawn the same on both sides, under them."},"flute_bottom_y":{"label":"The long flute: its lower edge on the round body, above the rail","kind":"length","measurements":[{"id":"eu-camera","value":1.875,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"both side photos' fitted cameras (this file's note): 495.7 and 486.0 px/in where they look, each lens 24 in off and 20 degrees up; scales from .length, heights from the tube's centre line","method":"row 835 down column 970 of the left photo (1.875) and row 816 down column 1200 of the right (1.874)","via":"harvest"}}]},"flute_top_y":{"label":"The long flute: its upper edge on the round body, above the rail","kind":"length","measurements":[{"id":"eu-camera","value":2.15,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"both side photos' fitted cameras (this file's note): 495.7 and 486.0 px/in where they look, each lens 24 in off and 20 degrees up; scales from .length, heights from the tube's centre line","method":"row 668 down column 970 of the left photo (2.141) and row 640 down column 1200 of the right (2.156)","via":"harvest"}}],"note":"Its upper edge is at the deck's foot. That it is sunk is read from its shading (a dark upper edge, a lit lower one, in both side photos and the obliques); how deep isn't seen (drawn detail_relief)."},"cross_bolt_x":{"label":"Mount: the cross bolt's axis, X","kind":"length","measurements":[{"id":"eu-camera","value":0.01,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"both side photos' fitted cameras (this file's note): 495.7 and 486.0 px/in where they look, each lens 24 in off and 20 degrees up; scales from .length, heights from the tube's centre line","method":"the bolt head's ring in the left photo (an ellipse about 1129.7, 1720.9, on the left jaw's face: x 0.015) and the bolt's end face in the right (about 1064.6, 1750.8, on its own plane, 0.93 in out: x 0.004)","via":"harvest"}}]},"cross_bolt_y":{"label":"Mount: the cross bolt's axis above the rail's top","kind":"length","measurements":[{"id":"eu-camera","value":0.015,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"both side photos' fitted cameras (this file's note): 495.7 and 486.0 px/in where they look, each lens 24 in off and 20 degrees up; scales from .length, heights from the tube's centre line","method":"the same two: the head's ring at y 0.007 on the left jaw's face, the end face at 0.022 on its own plane","via":"harvest"}},{"id":"end-user","value":0.08,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-aro 33a02158eb43 (ARO-RD2 end view from the rear, on white; supplied in chat)","scaleRef":"the end view's frame as profiles.front has it (135.4 px/in, rms 0.013 in over its five heights, 1.537 in across for Holosun's 1.54), z counted from the window's centre as that outline counts it (the mount is drawn from that outline)","method":"the nut's middle in the outline (y -0.145 to 0.299: 0.077) and the bolt's end's (0.014 to 0.169: 0.092), over the frame's rail top; the clamp's roof, picked at row 357, is at 0.014 in that frame","via":"user"},"note":"0.32 in over the jaws' bottom in this view, where each side photo has the bolt 0.22 to 0.24 over it."}],"adopt":{"from":"eu-camera","reason":"Two photos from opposite sides, each read from where its lens stood, agree within 0.015 in, and both have the bolt 0.22 to 0.24 in over the clamp's bottom; the rear view is one photo at 135 px/in, and puts it 0.32 over. A bolt at the rail's top has its lower half in a slot; one 0.08 over it would clear the rail altogether. The rear view's stays a visible conflict: a view from behind that looked down some 7 degrees would lift the bolt, 0.7 in further from its lens than the clamp's rear end, by that much."},"note":"At the rail's top: the bolt's lower half lies in a slot of the rail. Read as a square view the head was at 0.011 and the nut seemed 0.06 lower than it."},"bolt_head_d":{"label":"Mount: the cross bolt's head, on the left jaw, diameter","kind":"length","measurements":[{"id":"eu-camera","value":0.348,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"the left photo's fitted camera (this file's note): 495.7 px/in at the point it looks at, the lens 24 in off and 20 degrees up; its scale from .length, its height from the tube's centre line","method":"the dark ring round the head, fitted as an ellipse 173.8 px long (and 0.926 as tall: the lens is 22 degrees above it), on the left jaw's face","via":"harvest"}}],"note":"A round head with no socket showing, flush in the jaw's face with a groove round it (the rear view's outline has nothing standing out of the left jaw). Drawn standing detail_relief out, so that it shows."},"bolt_thread_d":{"label":"Mount: the cross bolt's threaded end, diameter","kind":"length","measurements":[{"id":"eu-camera","value":0.18,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/holosun-aro 6d33513e41f7 (Holosun EU, the right side, taken from 20 degrees above; 2200 px)","scaleRef":"the right photo's fitted camera (this file's note): 486.0 px/in at the point it looks at, the lens 24 in off and 20 degrees up, the photo rolled 0.42 degrees; its scale from .length, its height from the tube's centre line","method":"the end face's rim, 88 px across on its own plane (0.176); the threads behind it 94 px (0.19)","via":"harvest"}}]},"bolt_tip_z":{"label":"Mount: the cross bolt's end, from the window's centre","kind":"length","measurements":[{"id":"end-user","value":0.94,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 33a02158eb43 (ARO-RD2 end view from the rear, on white; supplied in chat)","scaleRef":"the end view's frame as profiles.front has it (135.4 px/in, rms 0.013 in over its five heights, 1.537 in across for Holosun's 1.54), z counted from the window's centre as that outline counts it (the mount is drawn from that outline)","method":"the outline's rightmost stretch, z +0.940 from y 0.01 to 0.17","via":"user"}}]},"nut_seat_z":{"label":"Mount: the nut's inner face, from the window's centre","kind":"length","measurements":[{"id":"end-user","value":0.641,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 33a02158eb43 (ARO-RD2 end view from the rear, on white; supplied in chat)","scaleRef":"the end view's frame as profiles.front has it (135.4 px/in, rms 0.013 in over its five heights, 1.537 in across for Holosun's 1.54), z counted from the window's centre as that outline counts it (the mount is drawn from that outline)","method":"where the nut begins in the outline: z +0.641 at its lower inner corner, +0.663 at its upper","via":"user"}}],"note":"The clamp's right jaw is the outline inside this; everything of the outline beyond it is the nut and the bolt, which are drawn as themselves."},"nut_outer_z":{"label":"Mount: the nut's outer face, from the window's centre","kind":"length","measurements":[{"id":"end-user","value":0.867,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 33a02158eb43 (ARO-RD2 end view from the rear, on white; supplied in chat)","scaleRef":"the end view's frame as profiles.front has it (135.4 px/in, rms 0.013 in over its five heights, 1.537 in across for Holosun's 1.54), z counted from the window's centre as that outline counts it (the mount is drawn from that outline)","method":"the outline's upright stretch at z +0.867, y -0.10 to -0.03","via":"user"}}]},"nut_across_flats":{"label":"Mount: the cross bolt's nut, across flats","kind":"length","measurements":[{"id":"eu-camera","value":0.375,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 6d33513e41f7 (Holosun EU, the right side, taken from 20 degrees above; 2200 px)","scaleRef":"the right photo's fitted camera (this file's note): 486.0 px/in at the point it looks at, the lens 24 in off and 20 degrees up, the photo rolled 0.42 degrees; its scale from .length, its height from the tube's centre line","method":"the hexagon's lowest corner (1062.7, 1836) on the nut's outer face: 0.212 in under the bolt's axis, and its two lower sides lie 7 degrees off a hexagon standing on a corner: 0.214 from axis to corner, 0.370 across flats","via":"harvest"}}],"note":"A 3/8 in hexagon, by the look of it, on a thread of 0.18 to 0.19 in. The rear view's outline has the nut 0.444 in tall (y -0.145 to 0.299), which is such a hexagon seen across its corners (0.433)."},"clamp_corner_chamfer":{"label":"Mount: the break of the clamp's four upright corners, along the rail","kind":"length","measurements":[{"id":"eu-camera","value":0.05,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"the left photo's fitted camera (this file's note): 495.7 px/in at the point it looks at, the lens 24 in off and 20 degrees up; its scale from .length, its height from the tube's centre line","method":"the left jaw's flat face ends at columns 785 and 1478.3 (x 0.706 and -0.685 on that face, z -0.563) and the clamp at 760 and 1503.3 (0.756 and -0.735): 0.050 at each end","via":"harvest"}}],"note":"A strip the jaw's whole height at each end of its face, in both side photos. How far it runs across isn't seen: drawn at 45 degrees."},"clamp_flank_top_y":{"label":"Mount: the top edge of each jaw's upright face at mid length, above the rail","kind":"length","measurements":[{"id":"eu-camera","value":0.197,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"the left photo's fitted camera (this file's note): 495.7 px/in at the point it looks at, the lens 24 in off and 20 degrees up; its scale from .length, its height from the tube's centre line","method":"the face's level top edge along row 1633.3 on the left jaw's face (z -0.563): 0.197; the ring round the bolt's head ends 0.014 under it","via":"harvest"}}],"note":"The straight rear view's outline has this edge at 0.243: it is a view from behind and a little above of a clamp 1.5 in deep, whose far end stands higher in it. The side photos' cameras are what the bolt's own height was taken from."},"clamp_flat_length":{"label":"Mount: the level middle of each jaw's top edge, and of the clamp's top under the stem, along the rail","kind":"length","measurements":[{"id":"eu-camera","value":0.413,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"the left photo's fitted camera (this file's note): 495.7 px/in at the point it looks at, the lens 24 in off and 20 degrees up; its scale from .length, its height from the tube's centre line","method":"the level edge's two ends at columns 1036.7 and 1243.3 of row 1633.3 (x 0.201 and -0.212): 0.413 about x -0.006; the fold where the clamp's top begins to fall is over the same two ends (column 1036.7 at rows 1493 to 1557)","via":"harvest"}}]},"clamp_flank_end_y":{"label":"Mount: the top edge of each jaw's upright face at the face's two ends, above the rail","kind":"length","measurements":[{"id":"eu-camera","value":0.02,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"the left photo's fitted camera (this file's note): 495.7 px/in at the point it looks at, the lens 24 in off and 20 degrees up; its scale from .length, its height from the tube's centre line","method":"the edge falls in a straight line from the level middle to (785, 1711.7) at the front and (1478.3, 1718.3) at the rear: 0.027 and 0.013 on the face","via":"harvest"}}],"note":"Each jaw's face is tallest at the bolt and falls to both ends, as a boat's side does."},"clamp_top_y":{"label":"Mount: the clamp's top where the stem stands (level, from one jaw's facet to the other's), above the rail","kind":"length","measurements":[{"id":"eu-camera","value":0.28,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"the left photo's fitted camera (this file's note): 495.7 px/in at the point it looks at, the lens 24 in off and 20 degrees up; its scale from .length, its height from the tube's centre line","method":"the facet's upper edge at mid length, (1023.3, 1568.3), on the top's edge as the rear view has it (clamp_saddle_width inside the jaw's face, z -0.415): 0.277; the edge along row 1566.7 a little further back: 0.286","via":"harvest"}}],"note":"In the stem's shadow in both side photos. The rear view's outline has it at 0.35 to 0.36 (the note at clamp_flank_top_y)."},"clamp_top_end_y":{"label":"Mount: the clamp's top at its two ends, above the rail","kind":"length","measurements":[{"id":"eu-camera","value":0.107,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"the left photo's fitted camera (this file's note): 495.7 px/in at the point it looks at, the lens 24 in off and 20 degrees up; its scale from .length, its height from the tube's centre line","method":"the facet's upper edge at the two ends, (761.7, 1640) and (1501.7, 1631.7): 0.121 and 0.139 if it lay straight over the middle's (z -0.415), 0.107 where its line of sight meets the facet drawn (the plane through the jaw's falling top edge at the middle facet's lean: z -0.381); the same line at x 0.305 comes to 0.231 for the 0.249 a straight fall from the level middle gives","via":"harvest"}}],"note":"The top falls from the level middle to each end. Drawn as a straight fall, level across. What the top really is at its two ends isn't settled: both side photos show a dark round-ended notch there (x 0.70 to 0.545 on the near jaw's plane in the left one), the two obliques a pocket stepped down into its middle from each end, Holosun's front and rear views (from about 30 degrees above) a dark face nearly the clamp's width with a lighter ledge under it over the rail."},"clamp_saddle_width":{"label":"Mount: the sloped facet between each jaw's upright face and the clamp's top, across","kind":"length","measurements":[{"id":"end-user","value":0.144,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-aro 33a02158eb43 (ARO-RD2 end view from the rear, on white; supplied in chat)","scaleRef":"the end view's frame as profiles.front has it (135.4 px/in, rms 0.013 in over its five heights, 1.537 in across for Holosun's 1.54)","method":"the outline's left side from the jaw's face (z -0.559) in to the top's edge (z -0.415), in two steps (a break at -0.504 to -0.467)","via":"user"}}],"note":"Drawn as one facet a side, the right jaw's the same as the left's (the nut hides the right's in this view)."},"stem_length":{"label":"Mount: the stem (the pedestal between the clamp and the optic's base), along the rail","kind":"length","measurements":[{"id":"eu-camera","value":0.935,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"the left photo's fitted camera (this file's note): 495.7 px/in at the point it looks at, the lens 24 in off and 20 degrees up; its scale from .length, its height from the tube's centre line","method":"its two upright edges at columns 903.3 and 1365 along row 1420 (x 0.473 and -0.462 on its side face, 0.475 and -0.466 on the middle plane): 0.935 about x 0.005","via":"harvest"}}]},"stem_panel_length":{"label":"Mount: the stem's side face (its widest stretch), along the rail","kind":"length","measurements":[{"id":"eu-camera","value":0.475,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"the left photo's fitted camera (this file's note): 495.7 px/in at the point it looks at, the lens 24 in off and 20 degrees up; its scale from .length, its height from the tube's centre line","method":"the two upright edges on the stem's side at columns 1025.7 (a lit band 22 px wide) and 1260: x 0.225 and -0.250","via":"harvest"}}],"note":"Ahead of it and behind it the stem's sides turn in to its two ends (the left front quarter's oblique, d968cfc95219, shows a narrower front face and a facet between)."},"stem_width":{"label":"Mount: the stem, across","kind":"length","measurements":[{"id":"end-user","value":0.273,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 33a02158eb43 (ARO-RD2 end view from the rear, on white; supplied in chat)","scaleRef":"the end view's frame as profiles.front has it (135.4 px/in, rms 0.013 in over its five heights, 1.537 in across for Holosun's 1.54)","method":"the outline's two upright edges under the optic's base: z -0.116 and +0.157","via":"user"}}]},"stem_foot_y":{"label":"Mount: where the stem's upright side begins over its flared foot, above the rail","kind":"length","measurements":[{"id":"eu-camera","value":0.327,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 3233645ac025 (Holosun EU, the left side, taken from 20 degrees above; 2200 px)","scaleRef":"the left photo's fitted camera (this file's note): 495.7 px/in at the point it looks at, the lens 24 in off and 20 degrees up; its scale from .length, its height from the tube's centre line","method":"the lit line under the stem's side face along row 1493.3, on that face (z -0.136): 0.327; it runs on down each turned-in facet to the stem's end at the clamp's falling top ((1015, 1481.7) to (895, 1538.3))","via":"harvest"}}],"note":"A flare all round the stem's foot, 0.047 high at the middle. How far it reaches out isn't seen: drawn at 45 degrees."},"nut_recess_d":{"label":"Mount: the round pocket the nut sits in on the right jaw, diameter","kind":"length","measurements":[{"id":"eu-camera","value":0.48,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/holosun-aro 6d33513e41f7 (Holosun EU, the right side, taken from 20 degrees above; 2200 px)","scaleRef":"the right photo's fitted camera (this file's note): 486.0 px/in at the point it looks at, the lens 24 in off and 20 degrees up, the photo rolled 0.42 degrees; its scale from .length, its height from the tube's centre line","method":"the pocket's arch over the nut: its two sides at columns 1005 and 1120 of row 1592.5 (x -0.115 and 0.118) and its top at (1060, 1565), each where its line of sight meets the right jaw's facet as drawn: 0.238 and 0.242 from the bolt's axis","via":"harvest"}}]},"nut_recess_wing_length":{"label":"Mount: the pocket's two wings, end to end along the rail","kind":"length","measurements":[{"id":"eu-camera","value":0.829,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 6d33513e41f7 (Holosun EU, the right side, taken from 20 degrees above; 2200 px)","scaleRef":"the right photo's fitted camera (this file's note): 486.0 px/in at the point it looks at, the lens 24 in off and 20 degrees up, the photo rolled 0.42 degrees; its scale from .length, its height from the tube's centre line","method":"the wings' round ends at columns 867.5 and 1275 on the right jaw's face (z 0.641): x -0.397 and 0.432","via":"harvest"}}],"note":"A slot through the round pocket, level with the bolt: the clamping bar's seat. The two narrow slits down from its ends to the jaw's foot (0.012 in) aren't drawn."},"nut_recess_wing_top_y":{"label":"Mount: the pocket's wings, their upper edge above the rail","kind":"length","measurements":[{"id":"eu-camera","value":0.11,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 6d33513e41f7 (Holosun EU, the right side, taken from 20 degrees above; 2200 px)","scaleRef":"the right photo's fitted camera (this file's note): 486.0 px/in at the point it looks at, the lens 24 in off and 20 degrees up, the photo rolled 0.42 degrees; its scale from .length, its height from the tube's centre line","method":"row 1655 at column 960 on the right jaw's face: 0.110","via":"harvest"}}]},"nut_recess_wing_bottom_y":{"label":"Mount: the pocket's wings, their lower edge above the rail","kind":"length","measurements":[{"id":"eu-camera","value":-0.006,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-aro 6d33513e41f7 (Holosun EU, the right side, taken from 20 degrees above; 2200 px)","scaleRef":"the right photo's fitted camera (this file's note): 486.0 px/in at the point it looks at, the lens 24 in off and 20 degrees up, the photo rolled 0.42 degrees; its scale from .length, its height from the tube's centre line","method":"row 1707.5 at column 960 on the right jaw's face: -0.006","via":"harvest"}}]},"nut_recess_depth":{"label":"Mount: how deep the nut's pocket is sunk in the right jaw's face","kind":"length","measurements":[{"id":"assumed","value":0.08,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows the pocket in profile. Between what the right rear quarter's oblique suggests by eye (5ec56fffa262: the pocket's wall beside the nut about a quarter of the nut's own thickness, 0.05) and what the right photo's whole arch over the nut would need if the jaw's facet is as drawn (0.11).","via":"harvest"}}]},"stem_end_width":{"label":"Mount: the stem's two end faces, across","kind":"length","measurements":[{"id":"assumed","value":0.136,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: half of stem_width. The left front quarter's oblique (d968cfc95219) shows the front face narrower than the stem and a facet turning in to it; no camera is fitted to that photo, and the side photos don't see across the stem.","via":"harvest"}}]},"detail_relief":{"label":"How far the shallow pieces no view shows in profile are sunk or stand (the flutes, the HOLOSUN panels, the grooves round the buttons, the screws' heads, the bolt's head)","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the least the page draws (docs/research/model-detail-pass-2026-10-12.md). Each piece's own entry says what was seen of it.","via":"harvest"}}]}}},{"subject":"holosun-eps-carry","title":"Holosun EPS Carry enclosed pistol sight (EPS-CARRY-RD-2, black)","dimensions":{"length":{"label":"Length","kind":"length","measurements":[{"id":"drawing","value":1.61,"unit":"in","stated":"1.61 in","source":{"type":"spec","publisher":"manufacturer","name":"Holosun EU shop, the EPS Carry's dimensioned drawing (image 169abca1c98b on item 70155839's page)","url":"https://www.holosun.eu/p/70155839","retrieved":"2026-11-06","via":"harvest"},"note":"Between the side view's extension lines: the base's front face to its rear face, at the base's foot (the hood's front leans back above it)."},{"id":"us","value":1.63,"unit":"in","stated":"Body Dimensions 1.63\" × 1.07\" × 0.95\"","source":{"type":"spec","publisher":"manufacturer","name":"holosun.com, EPS-CARRY-RD-2","url":"https://www.holosun.com/products/eps-carry-rd-2","retrieved":"2026-11-06","via":"harvest"},"note":"Holosun's L × W × H order (the window, 0.77\" × 0.58\", is given width by height)."},{"id":"press","value":1.62,"unit":"in","stated":"Body Dimensions: 1.62 x 1.19 x 0.99 (EPS) or 1.62 x 1.07 x 0.95 (EPS Carry)","source":{"type":"spec","publisher":"review","name":"POLICE magazine, Holosun's launch release (\"Holosun Adds to Pistol Optic Line with the EPS and EPS Carry\")","url":"https://www.policemag.com/news/holosun-adds-to-pistol-optic-line-with-the-eps-and-eps-carry","retrieved":"2026-11-06","via":"harvest"}},{"id":"eu","value":41,"unit":"mm","stated":"Size: 41x24x27 mm","source":{"type":"spec","publisher":"manufacturer","name":"Holosun EU shop, EPS-CARRY-RD-2 (item 70155839)","url":"https://www.holosun.eu/p/70155839","retrieved":"2026-11-06","via":"harvest"},"note":"Its order is length × height × width: 24 mm is the 0.95 in height and 27 mm the 1.07 in width."}],"adopt":{"from":"drawing","reason":"Holosun's own drawing says what it spans, and the EU table's 41 mm (1.614 in) agrees with it; the US page's 1.63 and the launch release's 1.62 stay a visible conflict (0.01 to 0.02 in)."}},"width":{"label":"Width","kind":"length","measurements":[{"id":"drawing","value":1.05,"unit":"in","stated":"1.05 in","source":{"type":"spec","publisher":"manufacturer","name":"Holosun EU shop, the EPS Carry's dimensioned drawing (image 169abca1c98b on item 70155839's page)","url":"https://www.holosun.eu/p/70155839","retrieved":"2026-11-06","via":"harvest"},"note":"Between the end view's extension lines: the battery tray's cover on the right side to the left flank. The hood alone is 0.988 (hood_width), the base 0.999 (base_width)."},{"id":"us","value":1.07,"unit":"in","stated":"Body Dimensions 1.63\" × 1.07\" × 0.95\"","source":{"type":"spec","publisher":"manufacturer","name":"holosun.com, EPS-CARRY-RD-2","url":"https://www.holosun.com/products/eps-carry-rd-2","retrieved":"2026-11-06","via":"harvest"}},{"id":"eu","value":27,"unit":"mm","stated":"Size: 41x24x27 mm","source":{"type":"spec","publisher":"manufacturer","name":"Holosun EU shop, EPS-CARRY-RD-2 (item 70155839)","url":"https://www.holosun.eu/p/70155839","retrieved":"2026-11-06","via":"harvest"}},{"id":"eumrs","value":27.2,"unit":"mm","pm":0.05,"stated":"Size: 41x24.1x27.2 mm","source":{"type":"spec","publisher":"manufacturer","name":"Holosun EU shop, EPS-CARRY-GR-MRS (item 70155846)","url":"https://www.holosun.eu/p/70155846","retrieved":"2026-11-06","via":"harvest"}}],"adopt":{"from":"drawing","reason":"Holosun's drawing, which shows what the width is taken across (the tray's cover to the left flank); the underside photo reads 1.062 across the same two at its length's scale (473185f9c9a2: 930 px at row 900). The US page's 1.07, the EU's 27 mm (1.063) and 27.2 mm (1.071) stay a visible conflict: they may take the buttons' pad on the left flank in too, which the drawing has standing 0.008 in."}},"height":{"label":"Height","kind":"length","measurements":[{"id":"us","value":0.95,"unit":"in","pm":0.005,"stated":"Body Dimensions 1.63\" × 1.07\" × 0.95\"","source":{"type":"spec","publisher":"manufacturer","name":"holosun.com, EPS-CARRY-RD-2","url":"https://www.holosun.com/products/eps-carry-rd-2","retrieved":"2026-11-06","via":"harvest"}},{"id":"drawing","value":0.95,"unit":"in","pm":0.005,"stated":"0.95 in","source":{"type":"spec","publisher":"manufacturer","name":"Holosun EU shop, the EPS Carry's dimensioned drawing (image 169abca1c98b on item 70155839's page)","url":"https://www.holosun.eu/p/70155839","retrieved":"2026-11-06","via":"harvest"},"note":"The base's underside to the hood's top."},{"id":"eu","value":24,"unit":"mm","stated":"Size: 41x24x27 mm","source":{"type":"spec","publisher":"manufacturer","name":"Holosun EU shop, EPS-CARRY-RD-2 (item 70155839)","url":"https://www.holosun.eu/p/70155839","retrieved":"2026-11-06","via":"harvest"}}],"adopt":{"from":"us","reason":"Holosun's US page; its drawing gives the same, and the EU's 24 mm (0.945) agrees."}},"axis_above_base":{"label":"Optical axis above its own base (the plane its footprint meets a slide's deck in)","kind":"length","measurements":[{"id":"drawing","value":0.52,"unit":"in","stated":"0.52 in","source":{"type":"spec","publisher":"manufacturer","name":"Holosun EU shop, the EPS Carry's dimensioned drawing (image 169abca1c98b on item 70155839's page)","url":"https://www.holosun.eu/p/70155839","retrieved":"2026-11-06","via":"harvest"},"note":"The end view's dimension from the base's underside up. Its dashed upper extension line is drawn 0.59 in up by the drawing's own scale (a drafting slip); the window's middle is 0.523 in up (window_centre_y), which is where the figure lands."},{"id":"eu","value":13.2,"unit":"mm","stated":"line of sight height: 13.2 mm","source":{"type":"spec","publisher":"manufacturer","name":"Holosun EU shop, EPS-CARRY-RD-2 (item 70155839)","url":"https://www.holosun.eu/p/70155839","retrieved":"2026-11-06","via":"harvest"}}],"adopt":{"from":"drawing","reason":"Holosun's drawing and its EU table agree (13.2 mm is 0.520 in), and so does the window's middle on the drawing's scale (0.523)."}},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"us","value":1.23,"unit":"oz","stated":"Body Weight 1.23 oz","source":{"type":"spec","publisher":"manufacturer","name":"holosun.com, EPS-CARRY-RD-2","url":"https://www.holosun.com/products/eps-carry-rd-2","retrieved":"2026-11-06","via":"harvest"}},{"id":"press","value":1.23,"unit":"oz","stated":"Weight: 1.4 oz (EPS) or 1.23 oz (EPS Carry)","source":{"type":"spec","publisher":"review","name":"POLICE magazine, Holosun's launch release (\"Holosun Adds to Pistol Optic Line with the EPS and EPS Carry\")","url":"https://www.policemag.com/news/holosun-adds-to-pistol-optic-line-with-the-eps-and-eps-carry","retrieved":"2026-11-06","via":"harvest"}},{"id":"eu","value":28,"unit":"g","stated":"Weight: 28 g","source":{"type":"spec","publisher":"manufacturer","name":"Holosun EU shop, EPS-CARRY-RD-2 (item 70155839)","url":"https://www.holosun.eu/p/70155839","retrieved":"2026-11-06","via":"harvest"},"note":"0.99 oz."}],"adopt":{"from":"us","reason":"Holosun's US page and its launch release agree; the EU shop's 28 g stays a visible conflict (whether it is taken without the battery isn't said)."}},"window_width":{"label":"Window width (the glass's clear opening across)","kind":"length","measurements":[{"id":"us","value":0.77,"unit":"in","stated":"Window Size 0.77\" × 0.58\"","source":{"type":"spec","publisher":"manufacturer","name":"holosun.com, EPS-CARRY-RD-2","url":"https://www.holosun.com/products/eps-carry-rd-2","retrieved":"2026-11-06","via":"harvest"}},{"id":"eu","value":20,"unit":"mm","stated":"Lens size: 20x15 mm","source":{"type":"spec","publisher":"manufacturer","name":"Holosun EU shop, EPS-CARRY-RD-2 (item 70155839)","url":"https://www.holosun.eu/p/70155839","retrieved":"2026-11-06","via":"harvest"}},{"id":"drawing","value":0.78,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/holosun-eps-carry 169abca1c98b (Holosun EU, the EPS Carry's dimensioned drawing: front end view and left side view, line art, 2200 px)","scaleRef":"the drawing's own figures: the side view's 1.61 in length over 772 px (479.5 px/in) and 0.95 in height over 458 px (482.1 px/in), the end view's 0.95 in over 456.5 px (480.5 px/in) and 1.05 in over 507.5 px (483.3 px/in): one scale, 481 px/in, to 0.4%","method":"the end view's inner window line, columns 300 to 675 of the original (750 px at the crop's double scale)","via":"harvest"},"note":"The bezel's outer line round it is 0.806 across (window_bezel_width)."}],"adopt":{"from":"us","reason":"Holosun's figure; its drawing's inner line reads 0.78 and the EU's 20 mm (0.787) is the lens, a little larger than what it shows."}},"window_height":{"label":"Window height (the glass's clear opening up and down)","kind":"length","measurements":[{"id":"us","value":0.58,"unit":"in","stated":"Window Size 0.77\" × 0.58\"","source":{"type":"spec","publisher":"manufacturer","name":"holosun.com, EPS-CARRY-RD-2","url":"https://www.holosun.com/products/eps-carry-rd-2","retrieved":"2026-11-06","via":"harvest"}},{"id":"eu","value":15,"unit":"mm","stated":"Lens size: 20x15 mm","source":{"type":"spec","publisher":"manufacturer","name":"Holosun EU shop, EPS-CARRY-RD-2 (item 70155839)","url":"https://www.holosun.eu/p/70155839","retrieved":"2026-11-06","via":"harvest"}},{"id":"drawing","value":0.591,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/holosun-eps-carry 169abca1c98b (Holosun EU, the EPS Carry's dimensioned drawing: front end view and left side view, line art, 2200 px)","scaleRef":"the drawing's own figures: the side view's 1.61 in length over 772 px (479.5 px/in) and 0.95 in height over 458 px (482.1 px/in), the end view's 0.95 in over 456.5 px (480.5 px/in) and 1.05 in over 507.5 px (483.3 px/in): one scale, 481 px/in, to 0.4%","method":"the end view's inner window line at the middle, rows 836 to 1120 of the original","via":"harvest"}}],"adopt":{"from":"us","reason":"Holosun's figure; the drawing's inner line reads 0.591 and the EU's 15 mm (0.591) is the lens."}},"window_bezel_width":{"label":"The window's bezel across (its outer line on the front face)","kind":"length","measurements":[{"id":"drawing","value":0.806,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/holosun-eps-carry 169abca1c98b (Holosun EU, the EPS Carry's dimensioned drawing: front end view and left side view, line art, 2200 px)","scaleRef":"the drawing's own figures: the side view's 1.61 in length over 772 px (479.5 px/in) and 0.95 in height over 458 px (482.1 px/in), the end view's 0.95 in over 456.5 px (480.5 px/in) and 1.05 in over 507.5 px (483.3 px/in): one scale, 481 px/in, to 0.4%","method":"the end view's outer window line, columns 293.5 to 681 of the original","via":"harvest"}}]},"window_bezel_height":{"label":"The window's bezel up and down (its outer line, at the middle where the top arches up)","kind":"length","measurements":[{"id":"drawing","value":0.618,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/holosun-eps-carry 169abca1c98b (Holosun EU, the EPS Carry's dimensioned drawing: front end view and left side view, line art, 2200 px)","scaleRef":"the drawing's own figures: the side view's 1.61 in length over 772 px (479.5 px/in) and 0.95 in height over 458 px (482.1 px/in), the end view's 0.95 in over 456.5 px (480.5 px/in) and 1.05 in over 507.5 px (483.3 px/in): one scale, 481 px/in, to 0.4%","method":"the end view's outer window line at the middle, rows 829 to 1126 of the original; at its sides the top is 0.031 lower (window_arch)","via":"harvest"}}]},"window_arch":{"label":"How far the window's top edge rises at its middle over its ends","kind":"length","measurements":[{"id":"drawing","value":0.031,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/holosun-eps-carry 169abca1c98b (Holosun EU, the EPS Carry's dimensioned drawing: front end view and left side view, line art, 2200 px)","scaleRef":"the drawing's own figures: the side view's 1.61 in length over 772 px (479.5 px/in) and 0.95 in height over 458 px (482.1 px/in), the end view's 0.95 in over 456.5 px (480.5 px/in) and 1.05 in over 507.5 px (483.3 px/in): one scale, 481 px/in, to 0.4%","method":"the end view's outer window line: row 844 at its two upper corners' ends, 829 at the middle (15 px)","via":"harvest"}}]},"window_corner_r":{"label":"The window's corner radius (its bezel's outer line)","kind":"length","measurements":[{"id":"drawing","value":0.104,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/holosun-eps-carry 169abca1c98b (Holosun EU, the EPS Carry's dimensioned drawing: front end view and left side view, line art, 2200 px)","scaleRef":"the drawing's own figures: the side view's 1.61 in length over 772 px (479.5 px/in) and 0.95 in height over 458 px (482.1 px/in), the end view's 0.95 in over 456.5 px (480.5 px/in) and 1.05 in over 507.5 px (483.3 px/in): one scale, 481 px/in, to 0.4%","method":"the end view's outer window line: each corner's round runs 50 px along both sides","via":"harvest"}}]},"window_centre_y":{"label":"The window's middle above the base","kind":"length","measurements":[{"id":"drawing","value":0.523,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/holosun-eps-carry 169abca1c98b (Holosun EU, the EPS Carry's dimensioned drawing: front end view and left side view, line art, 2200 px)","scaleRef":"the drawing's own figures: the side view's 1.61 in length over 772 px (479.5 px/in) and 0.95 in height over 458 px (482.1 px/in), the end view's 0.95 in over 456.5 px (480.5 px/in) and 1.05 in over 507.5 px (483.3 px/in): one scale, 481 px/in, to 0.4%","method":"the end view's outer window line, rows 829 to 1126, its middle at row 977.5, against the base's underside at row 1229","via":"harvest"},"note":"Across, its middle is the hood's (column 487.3 against 487.5)."}]},"hood_width":{"label":"The hood's width across its flanks (the tray's cover and the buttons' pad left out)","kind":"length","measurements":[{"id":"drawing","value":0.988,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/holosun-eps-carry 169abca1c98b (Holosun EU, the EPS Carry's dimensioned drawing: front end view and left side view, line art, 2200 px)","scaleRef":"the drawing's own figures: the side view's 1.61 in length over 772 px (479.5 px/in) and 0.95 in height over 458 px (482.1 px/in), the end view's 0.95 in over 456.5 px (480.5 px/in) and 1.05 in over 507.5 px (483.3 px/in): one scale, 481 px/in, to 0.4%","method":"the end view's flanks above the base, columns 250 to 725 of the original","via":"harvest"}}]},"base_width":{"label":"The base's width","kind":"length","measurements":[{"id":"drawing","value":0.999,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/holosun-eps-carry 169abca1c98b (Holosun EU, the EPS Carry's dimensioned drawing: front end view and left side view, line art, 2200 px)","scaleRef":"the drawing's own figures: the side view's 1.61 in length over 772 px (479.5 px/in) and 0.95 in height over 458 px (482.1 px/in), the end view's 0.95 in over 456.5 px (480.5 px/in) and 1.05 in over 507.5 px (483.3 px/in): one scale, 481 px/in, to 0.4%","method":"the end view's base, columns 247.5 to 727.5 of the original","via":"harvest"}},{"id":"bottom","value":1.01,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/holosun-eps-carry 473185f9c9a2 (Holosun EU, the EPS Carry's underside straight on, front at the top, 2200 px)","scaleRef":"the base's own length, 1.61 in (.length), over its 1410 px (rows 389 to 1799 at column 1100: 875.8 px/in); its width without the tray's cover, 885 px (columns 677 to 1562 at row 1300), is 1.010 in at that scale against the drawing's 0.999 (1.1%)","method":"columns 677 to 1562 at row 1300, behind the tray's cover","via":"harvest"}}],"adopt":{"from":"drawing","reason":"Holosun's drawing, square on; the underside photo, scaled by the length, reads 1.1% wide."}},"hood_corner_r":{"label":"The round of the hood's two top edges","kind":"length","measurements":[{"id":"drawing","value":0.109,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/holosun-eps-carry 169abca1c98b (Holosun EU, the EPS Carry's dimensioned drawing: front end view and left side view, line art, 2200 px)","scaleRef":"the drawing's own figures: the side view's 1.61 in length over 772 px (479.5 px/in) and 0.95 in height over 458 px (482.1 px/in), the end view's 0.95 in over 456.5 px (480.5 px/in) and 1.05 in over 507.5 px (483.3 px/in): one scale, 481 px/in, to 0.4%","method":"the end view's two upper corners, each round 52 px along the top and down the flank; the side view has the round's lower tangent line 0.113 under the top","via":"harvest"}}]},"deck_y":{"label":"The deck's top behind the hood, above the base's underside","kind":"length","measurements":[{"id":"drawing","value":0.243,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/holosun-eps-carry 169abca1c98b (Holosun EU, the EPS Carry's dimensioned drawing: front end view and left side view, line art, 2200 px)","scaleRef":"the drawing's own figures: the side view's 1.61 in length over 772 px (479.5 px/in) and 0.95 in height over 458 px (482.1 px/in), the end view's 0.95 in over 456.5 px (480.5 px/in) and 1.05 in over 507.5 px (483.3 px/in): one scale, 481 px/in, to 0.4%","method":"the side view's deck line behind the hood's rear fillet, row 1104 of the original, against the underside at row 1221","via":"harvest"}}]},"hood_rear_from_rear":{"label":"The hood's rear face ahead of the base's rear face","kind":"length","measurements":[{"id":"drawing","value":0.587,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/holosun-eps-carry 169abca1c98b (Holosun EU, the EPS Carry's dimensioned drawing: front end view and left side view, line art, 2200 px)","scaleRef":"the drawing's own figures: the side view's 1.61 in length over 772 px (479.5 px/in) and 0.95 in height over 458 px (482.1 px/in), the end view's 0.95 in over 456.5 px (480.5 px/in) and 1.05 in over 507.5 px (483.3 px/in): one scale, 481 px/in, to 0.4%","method":"the side view's hood rear face, column 1572.5 of the original, against the rear face at column 1855","via":"harvest"},"note":"The traced side outline has it; this is the figure the screws' counterbores are held to."}]},"screw_from_rear":{"label":"The two screw holes' middle ahead of the base's rear face","kind":"length","measurements":[{"id":"bottom","value":0.503,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/holosun-eps-carry 473185f9c9a2 (Holosun EU, the EPS Carry's underside straight on, front at the top, 2200 px)","scaleRef":"the base's own length, 1.61 in (.length), over its 1410 px (rows 389 to 1799 at column 1100: 875.8 px/in); its width without the tray's cover, 885 px (columns 677 to 1562 at row 1300), is 1.010 in at that scale against the drawing's 0.999 (1.1%)","method":"the two through holes' centres, (872, 1358) and (1368, 1358), each the middle of its rim picked at four points on a crop of the original; 441 px ahead of the rear face's row 1799","via":"harvest"},"note":"The left side photo (75b98ec314e3, from about 24 degrees above) has the counterbores' middle 0.44 in ahead of its rear silhouette: the counterbores lie on the deck, which that view sees from above and behind its rear edge; the straight underside is taken."}]},"screw_spacing":{"label":"The two screw holes apart (centre to centre, across)","kind":"length","measurements":[{"id":"bottom","value":0.566,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/holosun-eps-carry 473185f9c9a2 (Holosun EU, the EPS Carry's underside straight on, front at the top, 2200 px)","scaleRef":"the base's own length, 1.61 in (.length), over its 1410 px (rows 389 to 1799 at column 1100: 875.8 px/in); its width without the tray's cover, 885 px (columns 677 to 1562 at row 1300), is 1.010 in at that scale against the drawing's 0.999 (1.1%)","method":"the two through holes' centres, columns 872 and 1368 (496 px); their middle at column 1120, the base's (677 to 1562: 1119.5)","via":"harvest"}}]},"screw_hole_d":{"label":"The screw holes' diameter where they meet the underside","kind":"length","measurements":[{"id":"bottom","value":0.171,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/holosun-eps-carry 473185f9c9a2 (Holosun EU, the EPS Carry's underside straight on, front at the top, 2200 px)","scaleRef":"the base's own length, 1.61 in (.length), over its 1410 px (rows 389 to 1799 at column 1100: 875.8 px/in); its width without the tray's cover, 885 px (columns 677 to 1562 at row 1300), is 1.010 in at that scale against the drawing's 0.999 (1.1%)","method":"each hole's rim across, 150 px","via":"harvest"}}]},"counterbore_d":{"label":"The screws' counterbores' diameter in the deck","kind":"length","measurements":[{"id":"photo","value":0.23,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-eps-carry 75b98ec314e3 (Holosun EU, the left side, from about 24 degrees above; 2200 px)","scaleRef":"the base's length, 1.61 in (.length), over its silhouette, columns 222 to 1975 (1088.8 px/in)","method":"the near counterbore's rim along the sight, columns 1372 to 1628 of the original (a level circle seen from above keeps its length along the line of sight's square)","via":"harvest"}}]},"counterbore_depth":{"label":"How deep the counterbores go down from the deck","kind":"length","measurements":[{"id":"assumed","value":0.1,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view shows a counterbore in section. The rear view (1f3739adf780) sees well down each one, a screw's head below the deck; taken as most of the deck's 0.243.","via":"harvest"}}]},"pin_from_rear":{"label":"The two small pockets beside the screws (the footprint's recoil bosses' seats) ahead of the rear face","kind":"length","measurements":[{"id":"bottom","value":0.554,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/holosun-eps-carry 473185f9c9a2 (Holosun EU, the EPS Carry's underside straight on, front at the top, 2200 px)","scaleRef":"the base's own length, 1.61 in (.length), over its 1410 px (rows 389 to 1799 at column 1100: 875.8 px/in); its width without the tray's cover, 885 px (columns 677 to 1562 at row 1300), is 1.010 in at that scale against the drawing's 0.999 (1.1%)","method":"the two small holes' centres, (752, 1315) and (1486, 1313), 485 px ahead of row 1799","via":"harvest"}}]},"pin_spacing":{"label":"The two small pockets apart (centre to centre, across)","kind":"length","measurements":[{"id":"bottom","value":0.838,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/holosun-eps-carry 473185f9c9a2 (Holosun EU, the EPS Carry's underside straight on, front at the top, 2200 px)","scaleRef":"the base's own length, 1.61 in (.length), over its 1410 px (rows 389 to 1799 at column 1100: 875.8 px/in); its width without the tray's cover, 885 px (columns 677 to 1562 at row 1300), is 1.010 in at that scale against the drawing's 0.999 (1.1%)","method":"columns 752 and 1486 (734 px)","via":"harvest"}}]},"pin_d":{"label":"The two small pockets' diameter","kind":"length","measurements":[{"id":"bottom","value":0.091,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/holosun-eps-carry 473185f9c9a2 (Holosun EU, the EPS Carry's underside straight on, front at the top, 2200 px)","scaleRef":"the base's own length, 1.61 in (.length), over its 1410 px (rows 389 to 1799 at column 1100: 875.8 px/in); its width without the tray's cover, 885 px (columns 677 to 1562 at row 1300), is 1.010 in at that scale against the drawing's 0.999 (1.1%)","method":"each rim across, 80 px","via":"harvest"}}]},"pocket_from_rear":{"label":"The row of four round pockets in the underside's front end, ahead of the rear face","kind":"length","measurements":[{"id":"bottom","value":1.482,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-eps-carry 473185f9c9a2 (Holosun EU, the EPS Carry's underside straight on, front at the top, 2200 px)","scaleRef":"the base's own length, 1.61 in (.length), over its 1410 px (rows 389 to 1799 at column 1100: 875.8 px/in); its width without the tray's cover, 885 px (columns 677 to 1562 at row 1300), is 1.010 in at that scale against the drawing's 0.999 (1.1%)","method":"the four pockets' centres on row 501, 1298 px ahead of row 1799","via":"harvest"},"note":"Holosun's EU shop: \"EPS/EPS Carry optics have an extended K-Footprint (4 additional holes)\"."}]},"pocket_inner_z":{"label":"The two inner pockets of the four, out from the middle","kind":"length","measurements":[{"id":"bottom","value":0.147,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-eps-carry 473185f9c9a2 (Holosun EU, the EPS Carry's underside straight on, front at the top, 2200 px)","scaleRef":"the base's own length, 1.61 in (.length), over its 1410 px (rows 389 to 1799 at column 1100: 875.8 px/in); its width without the tray's cover, 885 px (columns 677 to 1562 at row 1300), is 1.010 in at that scale against the drawing's 0.999 (1.1%)","method":"centres at columns 990.7 and 1246.9, 129.3 and 126.9 px from the base's middle (1120)","via":"harvest"}}]},"pocket_outer_z":{"label":"The two outer pockets of the four, out from the middle","kind":"length","measurements":[{"id":"bottom","value":0.335,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-eps-carry 473185f9c9a2 (Holosun EU, the EPS Carry's underside straight on, front at the top, 2200 px)","scaleRef":"the base's own length, 1.61 in (.length), over its 1410 px (rows 389 to 1799 at column 1100: 875.8 px/in); its width without the tray's cover, 885 px (columns 677 to 1562 at row 1300), is 1.010 in at that scale against the drawing's 0.999 (1.1%)","method":"centres at columns 825.6 and 1412, 294.4 and 292 px from the base's middle","via":"harvest"}}]},"pocket_d":{"label":"The four pockets' diameter","kind":"length","measurements":[{"id":"bottom","value":0.162,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/holosun-eps-carry 473185f9c9a2 (Holosun EU, the EPS Carry's underside straight on, front at the top, 2200 px)","scaleRef":"the base's own length, 1.61 in (.length), over its 1410 px (rows 389 to 1799 at column 1100: 875.8 px/in); its width without the tray's cover, 885 px (columns 677 to 1562 at row 1300), is 1.010 in at that scale against the drawing's 0.999 (1.1%)","method":"each rim across, 142 px","via":"harvest"}}]},"pocket_depth":{"label":"How deep the underside's pockets are","kind":"length","measurements":[{"id":"assumed","value":0.05,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the underside photo (473185f9c9a2) shows each pocket's floor, not its depth; taken as a fifth of the base.","via":"harvest"}}]},"pad_rear":{"label":"The buttons' pad on the left flank, its rear edge ahead of the base's rear face","kind":"length","measurements":[{"id":"drawing","value":0.647,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/holosun-eps-carry 169abca1c98b (Holosun EU, the EPS Carry's dimensioned drawing: front end view and left side view, line art, 2200 px)","scaleRef":"the drawing's own figures: the side view's 1.61 in length over 772 px (479.5 px/in) and 0.95 in height over 458 px (482.1 px/in), the end view's 0.95 in over 456.5 px (480.5 px/in) and 1.05 in over 507.5 px (483.3 px/in): one scale, 481 px/in, to 0.4%","method":"the side view's pad, its rear edge at column 1544 of the original","via":"harvest"}}]},"pad_front":{"label":"The buttons' pad, its front edge (at its middle height) ahead of the base's rear face","kind":"length","measurements":[{"id":"drawing","value":1.42,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/holosun-eps-carry 169abca1c98b (Holosun EU, the EPS Carry's dimensioned drawing: front end view and left side view, line art, 2200 px)","scaleRef":"the drawing's own figures: the side view's 1.61 in length over 772 px (479.5 px/in) and 0.95 in height over 458 px (482.1 px/in), the end view's 0.95 in over 456.5 px (480.5 px/in) and 1.05 in over 507.5 px (483.3 px/in): one scale, 481 px/in, to 0.4%","method":"the side view's pad, its front edge at column 1172 of the original at the pad's middle height; it leans back as the hood's front face does (1.445 at its foot, 1.395 at its top)","via":"harvest"}}]},"pad_bottom":{"label":"The buttons' pad, its lower edge above the base's underside","kind":"length","measurements":[{"id":"drawing","value":0.373,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/holosun-eps-carry 169abca1c98b (Holosun EU, the EPS Carry's dimensioned drawing: front end view and left side view, line art, 2200 px)","scaleRef":"the drawing's own figures: the side view's 1.61 in length over 772 px (479.5 px/in) and 0.95 in height over 458 px (482.1 px/in), the end view's 0.95 in over 456.5 px (480.5 px/in) and 1.05 in over 507.5 px (483.3 px/in): one scale, 481 px/in, to 0.4%","method":"the side view's pad, row 1041.5 of the original","via":"harvest"}}]},"pad_top":{"label":"The buttons' pad, its upper edge above the base's underside","kind":"length","measurements":[{"id":"drawing","value":0.747,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/holosun-eps-carry 169abca1c98b (Holosun EU, the EPS Carry's dimensioned drawing: front end view and left side view, line art, 2200 px)","scaleRef":"the drawing's own figures: the side view's 1.61 in length over 772 px (479.5 px/in) and 0.95 in height over 458 px (482.1 px/in), the end view's 0.95 in over 456.5 px (480.5 px/in) and 1.05 in over 507.5 px (483.3 px/in): one scale, 481 px/in, to 0.4%","method":"the side view's pad, row 861.5 of the original","via":"harvest"}}]},"pad_proud":{"label":"How far the buttons' pad stands from the left flank","kind":"length","measurements":[{"id":"drawing","value":0.008,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/holosun-eps-carry 169abca1c98b (Holosun EU, the EPS Carry's dimensioned drawing: front end view and left side view, line art, 2200 px)","scaleRef":"the drawing's own figures: the side view's 1.61 in length over 772 px (479.5 px/in) and 0.95 in height over 458 px (482.1 px/in), the end view's 0.95 in over 456.5 px (480.5 px/in) and 1.05 in over 507.5 px (483.3 px/in): one scale, 481 px/in, to 0.4%","method":"the end view: the pad's edge 4 px of the crop's double scale (2 px of the original) out of the left flank's line, rows 912 to 1010","via":"harvest"},"note":"At the page's size a step of 0.008 is under a pixel (CLAUDE.md): the pad is drawn as its own edge's groove round it and the buttons' rings, not as a step."}]},"button_rear":{"label":"The minus button's centre ahead of the base's rear face","kind":"length","measurements":[{"id":"drawing","value":0.835,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/holosun-eps-carry 169abca1c98b (Holosun EU, the EPS Carry's dimensioned drawing: front end view and left side view, line art, 2200 px)","scaleRef":"the drawing's own figures: the side view's 1.61 in length over 772 px (479.5 px/in) and 0.95 in height over 458 px (482.1 px/in), the end view's 0.95 in over 456.5 px (480.5 px/in) and 1.05 in over 507.5 px (483.3 px/in): one scale, 481 px/in, to 0.4%","method":"the side view's minus button, its outer ring's centre at column 1453.5 of the original","via":"harvest"}}]},"button_front":{"label":"The plus button's centre ahead of the base's rear face","kind":"length","measurements":[{"id":"drawing","value":1.229,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/holosun-eps-carry 169abca1c98b (Holosun EU, the EPS Carry's dimensioned drawing: front end view and left side view, line art, 2200 px)","scaleRef":"the drawing's own figures: the side view's 1.61 in length over 772 px (479.5 px/in) and 0.95 in height over 458 px (482.1 px/in), the end view's 0.95 in over 456.5 px (480.5 px/in) and 1.05 in over 507.5 px (483.3 px/in): one scale, 481 px/in, to 0.4%","method":"the side view's plus button, its outer ring's centre at column 1264 of the original","via":"harvest"}}]},"button_y":{"label":"The two buttons' centres above the base's underside","kind":"length","measurements":[{"id":"drawing","value":0.563,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/holosun-eps-carry 169abca1c98b (Holosun EU, the EPS Carry's dimensioned drawing: front end view and left side view, line art, 2200 px)","scaleRef":"the drawing's own figures: the side view's 1.61 in length over 772 px (479.5 px/in) and 0.95 in height over 458 px (482.1 px/in), the end view's 0.95 in over 456.5 px (480.5 px/in) and 1.05 in over 507.5 px (483.3 px/in): one scale, 481 px/in, to 0.4%","method":"the side view's two buttons, their rings' centres on row 950 of the original","via":"harvest"}}]},"button_d":{"label":"The buttons' outer ring across","kind":"length","measurements":[{"id":"drawing","value":0.312,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/holosun-eps-carry 169abca1c98b (Holosun EU, the EPS Carry's dimensioned drawing: front end view and left side view, line art, 2200 px)","scaleRef":"the drawing's own figures: the side view's 1.61 in length over 772 px (479.5 px/in) and 0.95 in height over 458 px (482.1 px/in), the end view's 0.95 in over 456.5 px (480.5 px/in) and 1.05 in over 507.5 px (483.3 px/in): one scale, 481 px/in, to 0.4%","method":"each outer ring, 150 px across in the original; the inner ring 125 px (0.26)","via":"harvest"}}]},"button_inner_d":{"label":"The buttons' inner ring across (the button's face inside its groove)","kind":"length","measurements":[{"id":"drawing","value":0.26,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/holosun-eps-carry 169abca1c98b (Holosun EU, the EPS Carry's dimensioned drawing: front end view and left side view, line art, 2200 px)","scaleRef":"the drawing's own figures: the side view's 1.61 in length over 772 px (479.5 px/in) and 0.95 in height over 458 px (482.1 px/in), the end view's 0.95 in over 456.5 px (480.5 px/in) and 1.05 in over 507.5 px (483.3 px/in): one scale, 481 px/in, to 0.4%","method":"each inner ring, 125 px across in the original","via":"harvest"}}]},"lip_from_rear":{"label":"The raised lip across the deck's rear end, its front edge ahead of the rear face","kind":"length","measurements":[{"id":"drawing","value":0.187,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/holosun-eps-carry 169abca1c98b (Holosun EU, the EPS Carry's dimensioned drawing: front end view and left side view, line art, 2200 px)","scaleRef":"the drawing's own figures: the side view's 1.61 in length over 772 px (479.5 px/in) and 0.95 in height over 458 px (482.1 px/in), the end view's 0.95 in over 456.5 px (480.5 px/in) and 1.05 in over 507.5 px (483.3 px/in): one scale, 481 px/in, to 0.4%","method":"the side view: the lip's top begins at column 1765 of the original, after a round up from the deck","via":"harvest"}}]},"lip_y":{"label":"The lip's top above the base's underside","kind":"length","measurements":[{"id":"drawing","value":0.29,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/holosun-eps-carry 169abca1c98b (Holosun EU, the EPS Carry's dimensioned drawing: front end view and left side view, line art, 2200 px)","scaleRef":"the drawing's own figures: the side view's 1.61 in length over 772 px (479.5 px/in) and 0.95 in height over 458 px (482.1 px/in), the end view's 0.95 in over 456.5 px (480.5 px/in) and 1.05 in over 507.5 px (483.3 px/in): one scale, 481 px/in, to 0.4%","method":"the side view's lip top, row 1081.5 of the original","via":"harvest"},"note":"The traced side outline has it as its rear top; its corner facets (the side view's wedge at columns 1787 to 1855, rows 1105 to 1142) are lip_facet."}]},"lip_facet":{"label":"How far down the side each of the lip's rear corner facets runs from the lip's top","kind":"length","measurements":[{"id":"drawing","value":0.127,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/holosun-eps-carry 169abca1c98b (Holosun EU, the EPS Carry's dimensioned drawing: front end view and left side view, line art, 2200 px)","scaleRef":"the drawing's own figures: the side view's 1.61 in length over 772 px (479.5 px/in) and 0.95 in height over 458 px (482.1 px/in), the end view's 0.95 in over 456.5 px (480.5 px/in) and 1.05 in over 507.5 px (483.3 px/in): one scale, 481 px/in, to 0.4%","method":"the side view's facet: from the lip's top (row 1081.5) to its lowest point on the flank (row 1142.5), its front end 0.14 in ahead of the rear face (column 1787); the rear view (1f3739adf780) has the two facets sloping down and out from the lip's middle, where the elevation adjuster sits","via":"harvest"}}]},"tray_rear":{"label":"The battery tray's cover on the right flank, its rear end ahead of the base's rear face","kind":"length","measurements":[{"id":"photo","value":0.858,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-eps-carry 516b35e9e5a7 (Holosun EU, the right side, from about 24 degrees above; 2200 px)","scaleRef":"the base's length, 1.61 in (.length), over its silhouette (938 px/in on the picture as shown, 1068 px/in on the original)","method":"the cover's rear end, 805 px of the picture as shown ahead of the rear face","via":"harvest"}}]},"tray_front":{"label":"The battery tray's cover, its front end ahead of the base's rear face","kind":"length","measurements":[{"id":"photo","value":1.551,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-eps-carry 516b35e9e5a7 (Holosun EU, the right side, from about 24 degrees above; 2200 px)","scaleRef":"the base's length, 1.61 in (.length), over its silhouette (938 px/in on the picture as shown)","method":"the cover's front end, 1455 px of the picture as shown ahead of the rear face","via":"harvest"}}]},"tray_bottom":{"label":"The tray's cover, its lower edge above the base's underside","kind":"length","measurements":[{"id":"drawing","value":0.019,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/holosun-eps-carry 169abca1c98b (Holosun EU, the EPS Carry's dimensioned drawing: front end view and left side view, line art, 2200 px)","scaleRef":"the drawing's own figures: the side view's 1.61 in length over 772 px (479.5 px/in) and 0.95 in height over 458 px (482.1 px/in), the end view's 0.95 in over 456.5 px (480.5 px/in) and 1.05 in over 507.5 px (483.3 px/in): one scale, 481 px/in, to 0.4%","method":"the end view's bump on the right flank, its foot at row 1220 of the original","via":"harvest"}}]},"tray_top":{"label":"The tray's cover, its top (the stem round its screw) above the base's underside","kind":"length","measurements":[{"id":"drawing","value":0.378,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/holosun-eps-carry 169abca1c98b (Holosun EU, the EPS Carry's dimensioned drawing: front end view and left side view, line art, 2200 px)","scaleRef":"the drawing's own figures: the side view's 1.61 in length over 772 px (479.5 px/in) and 0.95 in height over 458 px (482.1 px/in), the end view's 0.95 in over 456.5 px (480.5 px/in) and 1.05 in over 507.5 px (483.3 px/in): one scale, 481 px/in, to 0.4%","method":"the end view's bump, its top at row 1047.5 of the original","via":"harvest"}}]},"tray_body_top":{"label":"The tray's cover, the top of its wide lower part above the base's underside","kind":"length","measurements":[{"id":"photo","value":0.256,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-eps-carry 516b35e9e5a7 (Holosun EU, the right side, from about 24 degrees above; 2200 px)","scaleRef":"the base's length, 1.61 in (.length), over its silhouette (938 px/in on the picture as shown)","method":"the cover's wide lower part's top edge, 240 px of the picture as shown over the base's foot; the stem round the screw rises 0.368 there (the drawing's 0.378)","via":"harvest"}}]},"tray_stem_rear":{"label":"The stem round the tray's screw, its rear end ahead of the base's rear face","kind":"length","measurements":[{"id":"photo","value":1.02,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-eps-carry 516b35e9e5a7 (Holosun EU, the right side; 2200 px)","scaleRef":"the base's length, 1.61 in (.length), over its silhouette (938 px/in on the picture as shown)","method":"the stem's rear shoulder, 960 px of the picture as shown ahead of the rear face","via":"harvest"}}]},"tray_stem_front":{"label":"The stem round the tray's screw, its front end ahead of the base's rear face","kind":"length","measurements":[{"id":"photo","value":1.32,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-eps-carry 516b35e9e5a7 (Holosun EU, the right side; 2200 px)","scaleRef":"the base's length, 1.61 in (.length), over its silhouette (938 px/in on the picture as shown)","method":"the stem's front shoulder, 1240 px of the picture as shown ahead of the rear face","via":"harvest"}}]},"tray_out":{"label":"How far the tray's cover stands from the right flank","kind":"length","measurements":[{"id":"drawing","value":0.062,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/holosun-eps-carry 169abca1c98b (Holosun EU, the EPS Carry's dimensioned drawing: front end view and left side view, line art, 2200 px)","scaleRef":"the drawing's own figures: the side view's 1.61 in length over 772 px (479.5 px/in) and 0.95 in height over 458 px (482.1 px/in), the end view's 0.95 in over 456.5 px (480.5 px/in) and 1.05 in over 507.5 px (483.3 px/in): one scale, 481 px/in, to 0.4%","method":"the end view's bump, columns 220 to 250 of the original against the flank","via":"harvest"}}]},"tray_screw_d":{"label":"The tray's screw head across","kind":"length","measurements":[{"id":"photo","value":0.16,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-eps-carry 516b35e9e5a7 (Holosun EU, the right side; 2200 px)","scaleRef":"the base's length, 1.61 in (.length), over its silhouette (938 px/in on the picture as shown)","method":"the slotted head's rim across, 150 px of the picture as shown; its centre 1.173 in ahead of the rear face and 0.256 up","via":"harvest"}}]},"tray_screw_x":{"label":"The tray's screw ahead of the base's rear face","kind":"length","measurements":[{"id":"photo","value":1.173,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-eps-carry 516b35e9e5a7 (Holosun EU, the right side; 2200 px)","scaleRef":"the base's length, 1.61 in (.length), over its silhouette (938 px/in on the picture as shown)","method":"the slotted head's centre, 1100 px of the picture as shown ahead of the rear face","via":"harvest"}}]},"windage_x":{"label":"The windage adjuster on the right side of the base, its centre ahead of the rear face","kind":"length","measurements":[{"id":"photo","value":0.192,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-eps-carry 516b35e9e5a7 (Holosun EU, the right side; 2200 px)","scaleRef":"the base's length, 1.61 in (.length), over its silhouette (938 px/in on the picture as shown)","method":"the adjuster's ring, its centre 180 px of the picture as shown ahead of the rear face and 155 px over the base's foot (0.165 in)","via":"harvest"}}]},"windage_y":{"label":"The windage adjuster's centre above the base's underside","kind":"length","measurements":[{"id":"photo","value":0.165,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-eps-carry 516b35e9e5a7 (Holosun EU, the right side; 2200 px)","scaleRef":"the base's length, 1.61 in (.length), over its silhouette (938 px/in on the picture as shown)","method":"the adjuster's ring's centre, 155 px of the picture as shown over the base's foot","via":"harvest"}}]},"adjuster_d":{"label":"The two adjusters' rings across (windage on the right side, elevation on the deck)","kind":"length","measurements":[{"id":"photo","value":0.176,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-eps-carry 516b35e9e5a7 (Holosun EU, the right side; 2200 px)","scaleRef":"the base's length, 1.61 in (.length), over its silhouette (938 px/in on the picture as shown)","method":"the windage adjuster's outer ring, 165 px of the picture as shown across; the elevation adjuster on the deck is its size in the rear view (1f3739adf780: 205 px against the screws' counterbores' 225)","via":"harvest"}}]},"elevation_x":{"label":"The elevation adjuster on the deck, its centre ahead of the rear face","kind":"length","measurements":[{"id":"photo","value":0.26,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-eps-carry 75b98ec314e3 (Holosun EU, the left side, from about 24 degrees above; 2200 px)","scaleRef":"the base's length, 1.61 in (.length), over its silhouette (941 px/in on the picture as shown)","method":"the adjuster's slotted head on the deck, its centre 244 px of the picture as shown ahead of the rear silhouette; the rear view has it in a notch in the lip's middle","via":"harvest"}}]},"feature_relief":{"label":"How deep the drawn grooves are sunk (round the pad, round each button, the adjusters' rings, the tray cover's slot)","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the least the page draws (docs/research/model-detail-pass-2026-10-12.md); no view shows these in section.","via":"harvest"}}]},"glass_inset":{"label":"How far each glass sits back from the face it shows in","kind":"length","measurements":[{"id":"assumed","value":0.04,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the front photo (333ae54a2b99) and the rear (1f3739adf780) show each glass a little down its bezel; no view shows how far.","via":"harvest"}}]},"rear_x":{"label":"The base's rear face in the optic frame (behind the screws' middle)","kind":"length","measurements":[{"id":"derived","value":-0.503,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"-{.screw_from_rear}","via":"harvest"},"note":"Where the traced outlines' rear-end origin sits in the part frame (their offset)."}]},"front_x":{"label":"The base's front face in the optic frame (ahead of the screws' middle)","kind":"length","measurements":[{"id":"derived","value":1.107,"unit":"in","pm":0.013,"source":{"type":"derived","expr":"{.length} - {.screw_from_rear}","via":"harvest"}}]},"glyph_length":{"label":"The + and - marks on the buttons, each bar's length","kind":"length","measurements":[{"id":"drawing","value":0.195,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/holosun-eps-carry 169abca1c98b (Holosun EU, the EPS Carry's dimensioned drawing: front end view and left side view, line art, 2200 px)","scaleRef":"the drawing's own figures: the side view's 1.61 in length over 772 px (479.5 px/in) and 0.95 in height over 458 px (482.1 px/in), the end view's 0.95 in over 456.5 px (480.5 px/in) and 1.05 in over 507.5 px (483.3 px/in): one scale, 481 px/in, to 0.4%","method":"the side view's plus and minus, each bar 94 px long in the original","via":"harvest"}}]},"glyph_width":{"label":"The + and - marks' bars, each one's width","kind":"length","measurements":[{"id":"drawing","value":0.026,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/holosun-eps-carry 169abca1c98b (Holosun EU, the EPS Carry's dimensioned drawing: front end view and left side view, line art, 2200 px)","scaleRef":"the drawing's own figures: the side view's 1.61 in length over 772 px (479.5 px/in) and 0.95 in height over 458 px (482.1 px/in), the end view's 0.95 in over 456.5 px (480.5 px/in) and 1.05 in over 507.5 px (483.3 px/in): one scale, 481 px/in, to 0.4%","method":"the side view's plus and minus, each bar 12.5 px wide in the original","via":"harvest"}}]},"panel_rear":{"label":"The HOLOSUN panel on the right flank, its rear end ahead of the base's rear face","kind":"length","measurements":[{"id":"photo","value":0.688,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-eps-carry 516b35e9e5a7 (Holosun EU, the right side, from about 24 degrees above; 2200 px)","scaleRef":"the base's length, 1.61 in (.length), over its silhouette (938 px/in on the picture as shown)","method":"the oval panel's rear end, 645 px of the picture as shown ahead of the rear face","via":"harvest"}}]},"panel_front":{"label":"The HOLOSUN panel, its front end ahead of the base's rear face","kind":"length","measurements":[{"id":"photo","value":1.381,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-eps-carry 516b35e9e5a7 (Holosun EU, the right side; 2200 px)","scaleRef":"the base's length, 1.61 in (.length), over its silhouette (938 px/in on the picture as shown)","method":"the oval panel's front end, 1295 px of the picture as shown ahead of the rear face","via":"harvest"}}]},"panel_bottom":{"label":"The HOLOSUN panel, its lower edge above the base's underside","kind":"length","measurements":[{"id":"photo","value":0.512,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/holosun-eps-carry 516b35e9e5a7 (Holosun EU, the right side, from about 24 degrees above; 2200 px)","scaleRef":"the base's length, 1.61 in (.length), over its silhouette (938 px/in on the picture as shown); heights on the flank as read, the view from above taking a few hundredths off them","method":"the oval panel's lower edge, 480 px of the picture as shown over the base's foot","via":"harvest"}}]},"panel_top":{"label":"The HOLOSUN panel, its upper edge above the base's underside","kind":"length","measurements":[{"id":"photo","value":0.701,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/holosun-eps-carry 516b35e9e5a7 (Holosun EU, the right side, from about 24 degrees above; 2200 px)","scaleRef":"the base's length, 1.61 in (.length), over its silhouette (938 px/in on the picture as shown)","method":"the oval panel's upper edge, 657 px of the picture as shown over the base's foot","via":"harvest"}}]},"glass_thickness":{"label":"How thick each glass is drawn","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view shows a glass's edge; a pane the light can catch.","via":"harvest"}}]},"top_panel_rear":{"label":"The HOLOSUN panel on the hood's top, its rear edge ahead of the base's rear face","kind":"length","measurements":[{"id":"photo","value":1.194,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-eps-carry 75b98ec314e3 (Holosun EU, the left side, from about 24 degrees above; 2200 px)","scaleRef":"the base's length, 1.61 in (.length), over its silhouette (941 px/in on the picture as shown)","method":"the top panel's rear edge, 1124 px of the picture as shown ahead of the rear silhouette (lengths along the sight are kept by a view from above)","via":"harvest"}}]},"top_panel_front":{"label":"The HOLOSUN panel on the hood's top, its front edge ahead of the base's rear face","kind":"length","measurements":[{"id":"photo","value":1.386,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-eps-carry 75b98ec314e3 (Holosun EU, the left side, from about 24 degrees above; 2200 px)","scaleRef":"the base's length, 1.61 in (.length), over its silhouette (941 px/in on the picture as shown)","method":"the top panel's front edge, 1304 px of the picture as shown ahead of the rear silhouette","via":"harvest"}}]},"top_panel_width":{"label":"The HOLOSUN panel on the hood's top, across","kind":"length","measurements":[{"id":"photo","value":0.53,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/holosun-eps-carry 75b98ec314e3 (Holosun EU, the left side, from about 24 degrees above; 2200 px)","scaleRef":"the base's length, 1.61 in (.length), over its silhouette (941 px/in on the picture as shown), and the view's angle above the sight, about 24 degrees (the counterbores' rims 0.42 as tall as wide)","method":"the panel's extent up the picture, 205 px, over the sine of the angle; the rear view (1f3739adf780) has it across most of the top's flat","via":"harvest"}}]},"facet_tip_from_rear":{"label":"Where each lip facet's wedge on the flank ends ahead of the base's rear face (at the deck's height)","kind":"length","measurements":[{"id":"drawing","value":0.14,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/holosun-eps-carry 169abca1c98b (Holosun EU, the EPS Carry's dimensioned drawing: front end view and left side view, line art, 2200 px)","scaleRef":"the drawing's own figures: the side view's 1.61 in length over 772 px (479.5 px/in) and 0.95 in height over 458 px (482.1 px/in), the end view's 0.95 in over 456.5 px (480.5 px/in) and 1.05 in over 507.5 px (483.3 px/in): one scale, 481 px/in, to 0.4%","method":"the side view's wedge: its front point at column 1787.5 of the original, on the deck's line","via":"harvest"}}]},"edge_break":{"label":"The break on the housing's machined edges","kind":"length","measurements":[{"id":"assumed","value":0.008,"unit":"in","pm":0.004,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: every edge of the housing is softly rounded in the EU photos (9c24edcfec2d, 75b98ec314e3), by less than any view resolves; drawn at the break the HS510C's model takes (holosun_hs510c.py BREAK).","via":"harvest"}}]},"plate_length":{"label":"The RMSc plate's length (along the sight)","kind":"length","measurements":[{"id":"eu","value":45,"unit":"mm","stated":"Size: 45x25x3","source":{"type":"spec","publisher":"manufacturer","name":"Holosun EU shop, HOLOSUN EPS Adapter for RMSc","url":"https://www.holosun.eu/en/detail/01909b76bc4772daa7a70885faae0166","retrieved":"2026-11-06","via":"harvest"},"note":"Length, width, thickness by its photos' proportions (a plate about as long as the sight and as wide, and thin). 1.772 in: 0.16 in longer than the sight's base."}]},"plate_width":{"label":"The RMSc plate's width","kind":"length","measurements":[{"id":"eu","value":25,"unit":"mm","stated":"Size: 45x25x3","source":{"type":"spec","publisher":"manufacturer","name":"Holosun EU shop, HOLOSUN EPS Adapter for RMSc","url":"https://www.holosun.eu/en/detail/01909b76bc4772daa7a70885faae0166","retrieved":"2026-11-06","via":"harvest"},"note":"0.984 in: the sight's base is 0.999."}]},"plate_thickness":{"label":"The RMSc plate's thickness (how far it raises the sight)","kind":"length","measurements":[{"id":"eu","value":3,"unit":"mm","stated":"Size: 45x25x3","source":{"type":"spec","publisher":"manufacturer","name":"Holosun EU shop, HOLOSUN EPS Adapter for RMSc","url":"https://www.holosun.eu/en/detail/01909b76bc4772daa7a70885faae0166","retrieved":"2026-11-06","via":"harvest"},"note":"0.118 in. The bosses on its top stand into the sight's own pockets and add nothing to it."}]},"plate_weight":{"label":"The RMSc plate's weight","kind":"mass","measurements":[{"id":"eu","value":30,"unit":"g","stated":"Weight: 30 g","source":{"type":"spec","publisher":"manufacturer","name":"Holosun EU shop, HOLOSUN EPS Adapter for RMSc","url":"https://www.holosun.eu/en/detail/01909b76bc4772daa7a70885faae0166","retrieved":"2026-11-06","via":"harvest"},"note":"Three times what 45 x 25 x 3 mm of aluminium weighs (9 g): with its packing and screws, by its figure; not the plate's own."}]},"plate_offset_x":{"label":"The RMSc pattern's middle on the plate, ahead of the K pattern's middle (the sight's screws' middle)","kind":"length","measurements":[{"id":"assumed","value":0,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file is square on the plate, and no page places either pattern's screws on it. Taken as one over the other (AT3 Tactical: \"The Holosun EPS uses the Holosun K footprint similar to the Shield RMSc cut but with some small differences\"); the ± is a quarter of the screws' spacing along the sight a plate could move them by.","via":"harvest"}}]},"plate_middle_x":{"label":"The plate's middle along the sight, ahead of the sight's screws' middle","kind":"length","measurements":[{"id":"assumed","value":0.302,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the plate centred under the sight's base (the base's middle is .length / 2 + .rear_x = 0.302), as both its photos have the sight's two ends' worth of plate to spare; no photo shows the two together.","via":"harvest"}}]},"plate_corner_r":{"label":"The plate's corner round","kind":"length","measurements":[{"id":"assumed","value":0.08,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: its two photos (6c35fcf048d5, ba2287d3c746) show rounded corners a little smaller than its holes, from a quarter.","via":"harvest"}}]},"plate_end_sag":{"label":"How far each of the plate's short ends arches out at its middle","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: both photos show the two short ends as shallow arcs; their sag isn't read from a quarter.","via":"harvest"}}]},"plate_hole_d":{"label":"The plate's corner holes' diameter","kind":"length","measurements":[{"id":"assumed","value":0.15,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the corner holes look a little smaller than the sight's screw holes in the photos (ba2287d3c746).","via":"harvest"}}]},"plate_hole_in":{"label":"The plate's corner holes' centres in from each end and from each side","kind":"length","measurements":[{"id":"assumed","value":0.14,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: in both photos each corner hole stands about its own diameter in from the end and from the side.","via":"harvest"}}]}}},{"subject":"holosun-hm3x","title":"Holosun HM3X 3× magnifier with flip mount (its spacer in or out)","dimensions":{"length":{"label":"Overall length","kind":"length","measurements":[{"id":"drawing","value":4.03,"unit":"in","source":{"type":"spec","publisher":"manufacturer","name":"Holosun EU dimensioned drawing","url":"https://www.holosun.eu/media/0d/db/21/1712753214/d6da8d95d91ffc9121f25e6d73b6602c.jpg","retrieved":"2026-09-30","via":"harvest"},"note":"Overall, including the eyepiece ring. The same drawing gives 3.48 in without it."},{"id":"spec","value":4,"unit":"in","stated":"4 × 1.7 × 2.5 in","source":{"type":"spec","publisher":"manufacturer","name":"holosun.com HM3X page","url":"https://www.holosun.com/products/hm3x","retrieved":"2026-09-30","via":"harvest"}},{"id":"manual","value":102,"unit":"mm","stated":"102×43×67 (L × W × H)","source":{"type":"spec","publisher":"manufacturer","name":"Holosun HM3X manual V2.2","url":"https://cdn.prod.website-files.com/68f92fcb2648b8aa5dc55d79/696084c37ac69a1d308fa08f_holosun-hm3x-manual.pdf","retrieved":"2026-09-30","via":"harvest"}},{"id":"eu","value":100,"unit":"mm","stated":"100x39x62 mm","source":{"type":"spec","publisher":"manufacturer","name":"Holosun EU shop","url":"https://www.holosun.eu/en/p/70128079","retrieved":"2026-09-30","via":"harvest"}},{"id":"review","value":100,"unit":"mm","stated":"39 × 100 × 62 mm without the spacer","source":{"type":"spec","publisher":"review","name":"SPARTANAT review","url":"https://spartanat.com/en/review-holosun-hm3x-magnifier","retrieved":"2026-09-30","via":"harvest"},"note":"The brief's figure. Identical to the EU listing, so possibly quoted rather than measured."}],"adopt":{"from":"drawing","reason":"Holosun's own dimensioned drawing is the most specific source."}},"width":{"label":"Width (magnifier and mount)","kind":"length","measurements":[{"id":"drawing","value":1.66,"unit":"in","source":{"type":"spec","publisher":"manufacturer","name":"Holosun EU dimensioned drawing","url":"https://www.holosun.eu/media/0d/db/21/1712753214/d6da8d95d91ffc9121f25e6d73b6602c.jpg","retrieved":"2026-09-30","via":"harvest"}},{"id":"spec","value":1.7,"unit":"in","stated":"4 × 1.7 × 2.5 in","source":{"type":"spec","publisher":"manufacturer","name":"holosun.com HM3X page","url":"https://www.holosun.com/products/hm3x","retrieved":"2026-09-30","via":"harvest"}},{"id":"manual","value":43,"unit":"mm","source":{"type":"spec","publisher":"manufacturer","name":"Holosun HM3X manual V2.2","url":"https://cdn.prod.website-files.com/68f92fcb2648b8aa5dc55d79/696084c37ac69a1d308fa08f_holosun-hm3x-manual.pdf","retrieved":"2026-09-30","via":"harvest"}},{"id":"review","value":39,"unit":"mm","stated":"39 × 100 × 62 mm without the spacer","source":{"type":"spec","publisher":"review","name":"SPARTANAT review","url":"https://spartanat.com/en/review-holosun-hm3x-magnifier","retrieved":"2026-09-30","via":"harvest"},"note":"Same as the EU listing."}],"adopt":{"from":"drawing","reason":"Dimensioned drawing."}},"height":{"label":"Height on mount, no spacer (housing top to the clamp jaws' bottom)","kind":"length","measurements":[{"id":"drawing","value":2.42,"unit":"in","source":{"type":"spec","publisher":"manufacturer","name":"Holosun EU dimensioned drawing","url":"https://www.holosun.eu/media/0d/db/21/1712753214/d6da8d95d91ffc9121f25e6d73b6602c.jpg","retrieved":"2026-09-30","via":"harvest"}},{"id":"spec","value":2.5,"unit":"in","stated":"4 × 1.7 × 2.5 in","source":{"type":"spec","publisher":"manufacturer","name":"holosun.com HM3X page","url":"https://www.holosun.com/products/hm3x","retrieved":"2026-09-30","via":"harvest"}},{"id":"review","value":62,"unit":"mm","stated":"39 × 100 × 62 mm without the spacer","source":{"type":"spec","publisher":"review","name":"SPARTANAT review","url":"https://spartanat.com/en/review-holosun-hm3x-magnifier","retrieved":"2026-09-30","via":"harvest"}}],"adopt":{"from":"drawing","reason":"Dimensioned drawing."},"note":"M3: the drawing's 2.42 runs to the bottom of the clamp jaws, which reach 0.22 in below the rail top (clamp_below_rail); the housing top is 2.20 in above the rail (top_above_rail_no_spacer). M2 read it as housing top to rail."},"height_with_spacer":{"label":"Height on mount, spacer installed","kind":"length","measurements":[{"id":"manual","value":67,"unit":"mm","stated":"102×43×67 (L × W × H)","source":{"type":"spec","publisher":"manufacturer","name":"Holosun HM3X manual V2.2","url":"https://cdn.prod.website-files.com/68f92fcb2648b8aa5dc55d79/696084c37ac69a1d308fa08f_holosun-hm3x-manual.pdf","retrieved":"2026-09-30","via":"harvest"},"note":"The manual doesn't say, but 67 mm matches the drawing height plus the spacer (see derived)."},{"id":"derived","value":2.64,"unit":"in","source":{"type":"derived","expr":"{.height} + {.spacer_thickness}","via":"harvest"}}],"adopt":{"from":"derived","reason":"Built from the drawing height and the manual's two center heights; agrees with the manual's 67 mm."}},"spacer_thickness":{"label":"Spacer thickness","kind":"length","measurements":[{"id":"derived","value":0.22,"unit":"in","source":{"type":"derived","expr":"{.optical_axis_above_rail_spacer} - {.optical_axis_above_rail_no_spacer}","via":"harvest"}},{"id":"review","value":5,"unit":"mm","stated":"5mm high riser","source":{"type":"spec","publisher":"review","name":"SPARTANAT review","url":"https://spartanat.com/en/review-holosun-hm3x-magnifier","retrieved":"2026-09-30","via":"harvest"}}],"adopt":{"from":"derived","reason":"From Holosun's own center heights. SPARTANAT's 5 mm matches its 35→40 mm heights, which disagree with Holosun's."}},"optical_axis_above_rail_no_spacer":{"label":"Lens center above rail, no spacer","kind":"length","measurements":[{"id":"manual","value":1.41,"unit":"in","stated":"Without the spacer, the center height is 1.41\" (Abs. CW).","source":{"type":"spec","publisher":"manufacturer","name":"Holosun HM3X manual V2.2","url":"https://cdn.prod.website-files.com/68f92fcb2648b8aa5dc55d79/696084c37ac69a1d308fa08f_holosun-hm3x-manual.pdf","retrieved":"2026-09-30","via":"harvest"}},{"id":"drawing","value":1.41,"unit":"in","source":{"type":"spec","publisher":"manufacturer","name":"Holosun EU dimensioned drawing","url":"https://www.holosun.eu/media/0d/db/21/1712753214/d6da8d95d91ffc9121f25e6d73b6602c.jpg","retrieved":"2026-09-30","via":"harvest"}},{"id":"eu","value":35.8,"unit":"mm","stated":"line of sight height: 35.8 mm","source":{"type":"spec","publisher":"manufacturer","name":"Holosun EU shop","url":"https://www.holosun.eu/en/p/70128079","retrieved":"2026-09-30","via":"harvest"}},{"id":"brief","value":35,"unit":"mm","source":{"type":"spec","publisher":"review","name":"SPARTANAT review (stated in the brief)","url":"https://spartanat.com/en/review-holosun-hm3x-magnifier","via":"brief"}}],"adopt":{"from":"manual","reason":"Holosun's manual, drawing and EU listing agree; the review's 35 mm is 0.8 mm lower."}},"optical_axis_above_rail_spacer":{"label":"Lens center above rail, spacer installed","kind":"length","measurements":[{"id":"manual","value":1.63,"unit":"in","stated":"With the spacer, the center height is 1.63\" (Lower 1/3 CW).","source":{"type":"spec","publisher":"manufacturer","name":"Holosun HM3X manual V2.2","url":"https://cdn.prod.website-files.com/68f92fcb2648b8aa5dc55d79/696084c37ac69a1d308fa08f_holosun-hm3x-manual.pdf","retrieved":"2026-09-30","via":"harvest"}},{"id":"brief","value":40,"unit":"mm","source":{"type":"spec","publisher":"review","name":"SPARTANAT review (stated in the brief)","url":"https://spartanat.com/en/review-holosun-hm3x-magnifier","via":"brief"}}],"adopt":{"from":"manual","reason":"Manufacturer figure, designed to match lower-1/3 red dots such as the ARO (1.63 in). The review's 40 mm is 1.4 mm lower. Caliper to confirm."}},"weight":{"label":"Weight with mount","kind":"mass","measurements":[{"id":"page","value":9.8,"unit":"oz","stated":"Body (oz) Weight 9.8 oz","source":{"type":"spec","publisher":"manufacturer","name":"holosun.com HM3X page","url":"https://www.holosun.com/products/hm3x","retrieved":"2026-09-30","via":"harvest"}},{"id":"manual","value":9.5,"unit":"oz","stated":"9.5 oz. (280g)","source":{"type":"spec","publisher":"manufacturer","name":"Holosun HM3X manual V2.2","url":"https://cdn.prod.website-files.com/68f92fcb2648b8aa5dc55d79/696084c37ac69a1d308fa08f_holosun-hm3x-manual.pdf","retrieved":"2026-09-30","via":"harvest"}},{"id":"eu","value":304,"unit":"g","source":{"type":"spec","publisher":"manufacturer","name":"Holosun EU shop","url":"https://www.holosun.eu/en/p/70128079","retrieved":"2026-09-30","via":"harvest"}},{"id":"combo","value":10.9,"unit":"oz","source":{"type":"spec","publisher":"manufacturer","name":"holosun.com ARO + HM3X combo page","url":"https://www.holosun.com/products/aro-core-rd-2-hm3x","retrieved":"2026-09-30","via":"harvest"}}],"adopt":{"from":"page","reason":"Current product page. Holosun's own sources give four different weights; weigh the part."},"note":"The weight of the magnifier set up either way (D95: its spacer in or out), one figure for both. None of Holosun's four says whether the spacer was on: the manual's \"9.5 oz. (280g)\" is beside its own \"default configuration\" of 1.41 in, without it, and nothing ties the page's 9.8 to either. The spacer is a block 0.22 in thick about the flip plate's length and width, a few hundredths of a cubic inch more than a tenth, or about a fifth of an ounce in aluminium (no page says what it is made of): less than Holosun's own figures differ by (9.5 to 10.9 oz), so no reading on file tells the two ways apart."},"eye_relief":{"label":"Eye relief","kind":"length","measurements":[{"id":"page","value":70,"unit":"mm","stated":"Eye Relief 70mm","source":{"type":"spec","publisher":"manufacturer","name":"holosun.com HM3X page","url":"https://www.holosun.com/products/hm3x","retrieved":"2026-09-30","via":"harvest"},"note":"From the page's OPTICAL DATA table; its text says \"70mm (2.75 inch) eye relief\"."}]},"eyepiece_rear_behind_base":{"label":"Eyepiece's rear face, behind the mount base's centre","kind":"length","measurements":[{"id":"drawing","value":2.995,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun dimensioned drawing, side view (inches))","scaleRef":"frame from the reviewed holes base_front_bottom, base_rear_bottom, base_front_top, base_rear_top, axis, interface, rail (214.1 px/in, rms 0.003 in over 7 points)","method":"−x_min of the traced outline (tools/trace.py); the eyepiece ring's rear face, behind the mount base's centre","via":"harvest"}}],"note":"Where the eye looks in: the eye relief runs back from here. Holosun's drawing dimensions the overall length (4.03) and the base (1.93), not where one sits along the other, so this is read off the traced outline of that drawing."},"body_length":{"label":"Housing length, objective end to the eyepiece ring","kind":"length","measurements":[{"id":"drawing","value":3.48,"unit":"in","source":{"type":"spec","publisher":"manufacturer","name":"Holosun EU dimensioned drawing","url":"https://www.holosun.eu/media/0d/db/21/1712753214/d6da8d95d91ffc9121f25e6d73b6602c.jpg","retrieved":"2026-09-30","via":"harvest"},"note":"Read as objective end to where the diopter (eyepiece) ring starts."}]},"objective_ring_od":{"label":"Objective-end ring outside diameter","kind":"length","measurements":[{"id":"drawing","value":1.32,"unit":"in","source":{"type":"spec","publisher":"manufacturer","name":"Holosun EU dimensioned drawing","url":"https://www.holosun.eu/media/0d/db/21/1712753214/d6da8d95d91ffc9121f25e6d73b6602c.jpg","retrieved":"2026-09-30","via":"harvest"},"note":"The left ring as drawn. Taken as the objective end because the larger right ring is the diopter ring."}]},"eyepiece_ring_od":{"label":"Eyepiece (diopter) ring outside diameter","kind":"length","measurements":[{"id":"drawing","value":1.42,"unit":"in","source":{"type":"spec","publisher":"manufacturer","name":"Holosun EU dimensioned drawing","url":"https://www.holosun.eu/media/0d/db/21/1712753214/d6da8d95d91ffc9121f25e6d73b6602c.jpg","retrieved":"2026-09-30","via":"harvest"}}]},"mount_base_length":{"label":"Flip-mount base length","kind":"length","measurements":[{"id":"drawing","value":1.93,"unit":"in","source":{"type":"spec","publisher":"manufacturer","name":"Holosun EU dimensioned drawing","url":"https://www.holosun.eu/media/0d/db/21/1712753214/d6da8d95d91ffc9121f25e6d73b6602c.jpg","retrieved":"2026-09-30","via":"harvest"}}],"note":"What the drawing's 1.93 spans (read 2026-10-05, for the hinge): its front extension line is the front knuckle's front face and its rear one the adjustment tool's knob's rear end (hinge_block_length, tool_knob_length: the right side view has them 1.88 apart), not the base's two ends; the base is as long as the hinge block, 1.73 in (base_plate_length), its front at the front extension line and its rear 0.2 in short of the rear one. The part frame's origin is the middle of the 1.93, as traced."},"top_to_mount_interface":{"label":"Housing top to the body/mount interface","kind":"length","measurements":[{"id":"drawing","value":1.76,"unit":"in","source":{"type":"spec","publisher":"manufacturer","name":"Holosun EU dimensioned drawing","url":"https://www.holosun.eu/media/0d/db/21/1712753214/d6da8d95d91ffc9121f25e6d73b6602c.jpg","retrieved":"2026-09-30","via":"harvest"}}]},"axis_to_mount_interface":{"label":"Optical axis to the body/mount interface","kind":"length","measurements":[{"id":"drawing","value":0.97,"unit":"in","source":{"type":"spec","publisher":"manufacturer","name":"Holosun EU dimensioned drawing","url":"https://www.holosun.eu/media/0d/db/21/1712753214/d6da8d95d91ffc9121f25e6d73b6602c.jpg","retrieved":"2026-09-30","via":"harvest"},"note":"The spacer goes in at this interface."}]},"top_above_rail_no_spacer":{"label":"Housing top above the rail top, no spacer","kind":"length","measurements":[{"id":"derived","value":2.2,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{.optical_axis_above_rail_no_spacer} + {.top_to_mount_interface} - {.axis_to_mount_interface}","via":"harvest"},"note":"The drawing's end view: axis 1.41 above the rail, the housing top 1.76 − 0.97 = 0.79 above the axis."}]},"clamp_below_rail":{"label":"Clamp jaws' bottom below the rail top","kind":"length","measurements":[{"id":"derived","value":0.22,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{.height} - {.top_above_rail_no_spacer}","via":"harvest"},"note":"The drawing's 2.42 (top to the jaws' bottom) less the housing top's 2.20 above the rail. The jaws wrap the rail's sides."}]},"eyepiece_glass_d":{"label":"Eyepiece glass, visible diameter","kind":"length","measurements":[{"id":"drawing","value":0.912,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, end view)","scaleRef":"the end view's least-squares frame on its dimension lines (214 px/in, rms 0.003 in)","method":"least-squares circle through the innermost circle's line pixels about the axis (radius 97.64 px, rms 1.6 px over 1,203 px), diameter at the line's centre; ± is half the line width and the fit","via":"harvest"}}],"note":"Draws the eyepiece lens (M5). Read on the drawing's end view, which is seen from the objective end (the seed's notes, 2026-10-05; when this was read it was taken as seen from the eyepiece): its concentric circles about the axis are that end's, and the innermost carries the retainer's six tabs and bounds the glass. Holosun's straight end-on picture from the same end (7994638176a5) shows the glass inside the six-tabbed retainer at about 0.66 of the fluted ring's width, which the drawing's 0.62 of its outer ring roughly matches (the flutes and the tabs make that a loose check). So the figure is the glass at the objective end, where a second reading agrees with it (objective_glass_d, 0.906); it stands for the eyepiece's too, no view on file looking square into the eyepiece."},"objective_glass_d":{"label":"Objective glass, visible diameter","kind":"length","measurements":[{"id":"photo-ratio","value":0.906,"unit":"in","pm":0.035,"source":{"type":"photo","photo":"references/holosun-hm3x 861951078234 (holosun.com, objective end, angled from above)","scaleRef":"holosun-hm3x.objective_ring_od (1.32 in, the drawing) in the same plane","method":"horizontal widths through the centre: glass inside the bevel 206 px, ring 300 px (ratio 0.687) × 1.32; ± covers the bevel's edges (±5 px) and the view's slight angle","via":"harvest"}}],"note":"Draws the objective lens (M5). No straight view of the objective end; in Holosun's angled one the glass and the objective ring are concentric circles in one plane, so the ratio of their widths survives the angle (weak perspective). Agrees with the eyepiece glass (0.912) and the reviews' '24 mm' (0.945, no source on file)."},"flip_angle":{"label":"How far the magnifier swings to the side on its mount","kind":"angle","measurements":[{"id":"manual","value":90,"unit":"deg","stated":"The magnifier can be flipped to the side 90 degrees (as shown in Figure 3).","source":{"type":"spec","publisher":"manufacturer","name":"Holosun HM3X manual V2.2","url":"https://cdn.prod.website-files.com/68f92fcb2648b8aa5dc55d79/696084c37ac69a1d308fa08f_holosun-hm3x-manual.pdf","retrieved":"2026-09-30","via":"harvest"}}],"note":"To the rifle's right: the hinge is on that side (the part's own notes on which side is which), and the manual's Figure 3 draws it swung over, lying beside the mount with its eyepiece still to the rear."},"hinge_axis_above_rail":{"label":"The flip mount's hinge axis above the rail top","kind":"length","measurements":[{"id":"side","value":0.44,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/holosun-hm3x eea64f6b7ff8 (holosun.com's gallery: the magnifier's right side, square on, 1000 px)","scaleRef":"holosun-hm3x.length across the picture (872 px: 216.4 px/in) and holosun-hm3x.eyepiece_ring_od upright in it (306 px: 215.5 px/in): one scale both ways, a view with no perspective to speak of","method":"the barrel's lit band between the knuckles, rows 636.5 to 701.5 at half its brightness (feet 631 to 706), its middle at row 669. The knuckle's top (0.709 above the rail in the drawing's end view) is at row 608 and the jaws' bottom (clamp_below_rail) at 815: the picture has those 0.957 in apart where the drawing has 0.930, so the middle is 0.427 from the one and 0.454 from the other, and the ± covers both","via":"harvest"}}],"note":"The hinge is a barrel between two knuckles on the mount's right side, along the rail. Its middle is level with the face the magnifier's foot sits on (0.44: optical_axis_above_rail_no_spacer less axis_to_mount_interface), as a plate hinged at its own top face would have it."},"hinge_axis_right_of_centre":{"label":"The flip mount's hinge axis to the right of the optical axis's vertical","kind":"length","measurements":[{"id":"plan","value":0.47,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/holosun-hm3x 9b4d7ab4e4c7 (Holosun EU's gallery, file 'hm3x mount_1.JPG': the flip mount alone from above, its hinge at the right, 2200 px)","scaleRef":"the hinge block's length in the same photo (1208 px), 1.728 in by the side view: 699 px/in; by the mount's width in the drawing's end view (1.53 in from the lever's outer edge to the knuckle's outer face, 1097 px) it is 717 px/in, and the ± covers both","method":"the barrel's edges at columns 1340 and 1588, its middle 333 px right of the plate's centre pin (column 1131, which is the middle of the mount by the drawing's end view within 0.002 in): 0.477 at one scale, 0.464 at the other","via":"harvest"}}]},"hinge_barrel_d":{"label":"The hinge barrel's diameter","kind":"length","measurements":[{"id":"plan","value":0.35,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-hm3x 9b4d7ab4e4c7 (Holosun EU's gallery, file 'hm3x mount_1.JPG': the flip mount alone from above, its hinge at the right, 2200 px)","scaleRef":"the hinge block's length in the same photo (1208 px), 1.728 in by the side view: 699 px/in; by the mount's width in the drawing's end view (1.53 in from the lever's outer edge to the knuckle's outer face, 1097 px) it is 717 px/in, and the ± covers both","method":"the barrel between the knuckles, columns 1340 to 1588 (248 px): 0.355 and 0.346 at the two scales","via":"harvest"}},{"id":"side","value":0.32,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-hm3x eea64f6b7ff8 (holosun.com's gallery: the magnifier's right side, square on, 1000 px)","scaleRef":"holosun-hm3x.length across the picture (872 px: 216.4 px/in) and holosun-hm3x.eyepiece_ring_od upright in it (306 px: 215.5 px/in): one scale both ways, a view with no perspective to speak of","method":"the barrel's lit band: 65 px at half its brightness, 75 px between its feet (0.30 to 0.35); a round bar lit from above darkens before its edge, so the band is a lower bound","via":"harvest"}}],"adopt":{"from":"plan","reason":"From above the barrel is seen against the darker plate and gap beside it, edge to edge; from the side only its lit band shows. The two agree within their ±."}},"hinge_block_length":{"label":"The hinge block's length along the rail (both knuckles and the barrel between them)","kind":"length","measurements":[{"id":"side","value":1.728,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/holosun-hm3x eea64f6b7ff8 (holosun.com's gallery: the magnifier's right side, square on, 1000 px)","scaleRef":"holosun-hm3x.length across the picture (872 px: 216.4 px/in) and holosun-hm3x.eyepiece_ring_od upright in it (306 px: 215.5 px/in): one scale both ways, a view with no perspective to speak of","method":"the block's rear and front faces at columns 535 and 909 (374 px)","via":"harvest"}},{"id":"drawing","value":1.729,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, side view)","scaleRef":"the side view's frame on its own dimension lines (214.1 px/in, the trace's)","method":"the traced outline: the front knuckle's front face at 0.967 and, behind the body's foot, a face as tall as the barrel at -0.762","via":"harvest"}}],"adopt":{"from":"side","reason":"The view that shows the block itself; the drawing's side view, of the other side, has its two ends where this puts them."},"note":"Its front end is the mount's front end: the drawing's side view has a block as tall as the knuckles (0.712 above the rail) from 0.633 to 0.967 ahead of the base's middle, the 1.93 in base's front extension line at 0.965."},"hinge_knuckle_length":{"label":"Each hinge knuckle's length along the rail","kind":"length","measurements":[{"id":"side","value":0.35,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-hm3x eea64f6b7ff8 (holosun.com's gallery: the magnifier's right side, square on, 1000 px)","scaleRef":"holosun-hm3x.length across the picture (872 px: 216.4 px/in) and holosun-hm3x.eyepiece_ring_od upright in it (306 px: 215.5 px/in): one scale both ways, a view with no perspective to speak of","method":"the rear knuckle columns 535 to 610 (0.347), the front 832 to 909 (0.356), the barrel's ends the dark seams between","via":"harvest"}},{"id":"drawing","value":0.334,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, side view)","scaleRef":"the side view's frame on its own dimension lines (214.1 px/in, the trace's)","method":"the traced outline's front block, 0.633 to 0.967","via":"harvest"}}],"adopt":{"from":"side","reason":"Both knuckles and their seams show in it."}},"hinge_seat_above_rail":{"label":"The mount's side under the hinge barrel: its top above the rail top","kind":"length","measurements":[{"id":"side","value":0.21,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-hm3x eea64f6b7ff8 (holosun.com's gallery: the magnifier's right side, square on, 1000 px)","scaleRef":"holosun-hm3x.length across the picture (872 px: 216.4 px/in) and holosun-hm3x.eyepiece_ring_od upright in it (306 px: 215.5 px/in): one scale both ways, a view with no perspective to speak of","method":"the floor of the gap the barrel lies in, row 718: 0.201 from the knuckle's top, 0.227 from the jaws' bottom (see hinge_axis_above_rail)","via":"harvest"}}]},"hinge_knuckle_inner_right_of_centre":{"label":"The hinge knuckles' inner face, right of the optical axis's vertical","kind":"length","measurements":[{"id":"plan","value":0.215,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-hm3x 9b4d7ab4e4c7 (Holosun EU's gallery, file 'hm3x mount_1.JPG': the flip mount alone from above, its hinge at the right, 2200 px)","scaleRef":"the hinge block's length in the same photo (1208 px), 1.728 in by the side view: 699 px/in; by the mount's width in the drawing's end view (1.53 in from the lever's outer edge to the knuckle's outer face, 1097 px) it is 717 px/in, and the ± covers both","method":"the knuckles' inner edge at column 1283, 152 px right of the plate's centre pin: 0.218 and 0.212","via":"harvest"}}],"note":"Their outer face is the drawing's end view's (0.655, the traced outline); the inner one is behind the magnifier's foot there."},"base_top_above_rail":{"label":"The mount base's top face above the rail top (what the flip plate lies on)","kind":"length","measurements":[{"id":"drawing","value":0.287,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, end view)","scaleRef":"the end view's frame on its own dimension lines (214.4 px/in, rms 0.001 in: the trace's)","method":"the traced outline's level stretch on the lever's side of the foot, from 0.26 to 0.56 left of the middle","via":"harvest"}}]},"base_plate_length":{"label":"The mount's base, along the rail","kind":"length","measurements":[{"id":"plan","value":1.6,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/holosun-hm3x 9b4d7ab4e4c7 (Holosun EU's gallery, file 'hm3x mount_1.JPG': the flip mount alone from above, its hinge at the right, 2200 px)","scaleRef":"the hinge block's length in the same photo (1208 px), 1.728 in by the side view: 699 px/in; by the mount's width in the drawing's end view (1.53 in from the lever's outer edge to the knuckle's outer face, 1097 px) it is 717 px/in, and the ± covers both","method":"the plate's front and rear edges, rows 504 and 1636 (1132 px): 1.62 and 1.58","via":"harvest"},"note":"Not a view square down on the mount: it is taken from above and behind, and the knuckles' tops stand 0.42 in nearer the lens than the plate's, so the hinge block reads longer than the plate (1208 px against 1132) and leans forward of it (112 px at the front, 36 behind at the rear). Read as the plate being shorter, which is the photo's lean."},{"id":"drawing","value":1.73,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, side view)","scaleRef":"the side view's frame on its own dimension lines (214.1 px/in, rms 0.003 in: the trace's), the mount's middle at column 548.25","method":"the base's front face at column 341.5 (rows 1150 to 1284) and its rear face at 712 (rows 1150 to 1190): 370.5 px. No line parts the base's front face from the front knuckle's in this view","via":"harvest"}}],"adopt":{"from":"drawing","reason":"The maker's own side view, square on and to scale, against one photo taken aslant from above and behind, in which what stands nearer the lens leans forward. Two more sources have the base as long as the hinge block and flush with its front: Primary Arms' photo of the left side (7602cbc9ffbd: the base's upper ledge 850 px at 479 px/in, 1.77 in, from column 110 to 960) and the manual's Figure 4, which draws the base's front face and the front knuckle's as one face."},"note":"As long as the hinge block beside it (hinge_block_length, 1.728) and flush with it at the front: one block in the drawing's side view, from the front knuckle's front face to a rear face 0.765 in behind the mount's middle. Read first (2026-10-05) between the top face's two edges on the picture of the mount from above, 1.6 in, with its front edge 0.16 in behind the front knuckle's (base_plate_front_behind_hinge_front): the base was drawn that long, and the rail channel under it, until 2026-10-13."},"base_plate_front_behind_hinge_front":{"label":"The base's front face, behind the hinge block's front end","kind":"length","measurements":[{"id":"plan","value":0.16,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-hm3x 9b4d7ab4e4c7 (Holosun EU's gallery, file 'hm3x mount_1.JPG': the flip mount alone from above, its hinge at the right, 2200 px)","scaleRef":"the hinge block's length in the same photo (1208 px), 1.728 in by the side view: 699 px/in; by the mount's width in the drawing's end view (1.53 in from the lever's outer edge to the knuckle's outer face, 1097 px) it is 717 px/in, and the ± covers both","method":"rows 392 (the front knuckle's front) and 504 (the plate's): 112 px","via":"harvest"},"note":"The knuckle's top is 0.42 in nearer the lens than the plate's, in a view from above and behind: it leans forward in the picture by about this much."},{"id":"drawing","value":0,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, side view)","scaleRef":"the side view's frame on its own dimension lines (214.1 px/in, rms 0.003 in: the trace's), the mount's middle at column 548.25","method":"one upright line is the front of both: column 341.5 along rows 1190 to 1284, where the base is, and 342.5 to 343 along rows 1150 and 1175, where the knuckle stands over it (a pixel and a half: 0.007 in). ± is two pixels","via":"harvest"}}],"adopt":{"from":"drawing","reason":"The drawing's side view has one front face for the base and the front knuckle, as the manual's Figure 4 draws them and as Primary Arms' photo of the left side has the base's ledge run forward of the far knuckle; the 0.16 in is the knuckle's lean in a photo taken from above and behind (base_plate_length's reason)."},"note":"Nothing: the two are one face (the drawing's side view, and the manual's Figure 4). The picture of the mount from above has the top face's front edge 0.16 in behind the front knuckle's, the knuckle standing nearer a lens that looks from above and behind (base_plate_length)."},"flip_plate_length":{"label":"The flip plate the magnifier's foot is screwed to: its length along the rail","kind":"length","measurements":[{"id":"plan","value":1,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/holosun-hm3x 9b4d7ab4e4c7 (Holosun EU's gallery, file 'hm3x mount_1.JPG': the flip mount alone from above, its hinge at the right, 2200 px)","scaleRef":"the hinge block's length in the same photo (1208 px), 1.728 in by the side view: 699 px/in; by the mount's width in the drawing's end view (1.53 in from the lever's outer edge to the knuckle's outer face, 1097 px) it is 717 px/in, and the ± covers both","method":"rows 664 to 1373 (709 px): 1.015 and 0.989","via":"harvest"}}],"note":"As long as the barrel it is one piece with, and between the knuckles with it."},"flip_plate_width":{"label":"The flip plate's width across the rail","kind":"length","measurements":[{"id":"plan","value":0.58,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-hm3x 9b4d7ab4e4c7 (Holosun EU's gallery, file 'hm3x mount_1.JPG': the flip mount alone from above, its hinge at the right, 2200 px)","scaleRef":"the hinge block's length in the same photo (1208 px), 1.728 in by the side view: 699 px/in; by the mount's width in the drawing's end view (1.53 in from the lever's outer edge to the knuckle's outer face, 1097 px) it is 717 px/in, and the ± covers both","method":"columns 927 to 1336 (409 px), centred on its pin: 0.585 and 0.570. The foot above it in the drawing's end view is 0.595 wide","via":"harvest"}}]},"flip_plate_screw_spacing":{"label":"The flip plate's two screws, apart along the rail","kind":"length","measurements":[{"id":"plan","value":0.69,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-hm3x 9b4d7ab4e4c7 (Holosun EU's gallery, file 'hm3x mount_1.JPG': the flip mount alone from above, its hinge at the right, 2200 px)","scaleRef":"the hinge block's length in the same photo (1208 px), 1.728 in by the side view: 699 px/in; by the mount's width in the drawing's end view (1.53 in from the lever's outer edge to the knuckle's outer face, 1097 px) it is 717 px/in, and the ± covers both","method":"the two holes' centres, rows 800 and 1291 (491 px): 0.703 and 0.685","via":"harvest"}}],"note":"The screws that hold the magnifier's foot, put in from the plate's underside (the manual's Figure 4): their heads show on it when the magnifier is swung aside (Figure 3)."},"flip_plate_screw_d":{"label":"The flip plate's screw holes, across","kind":"length","measurements":[{"id":"plan","value":0.16,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-hm3x 9b4d7ab4e4c7 (Holosun EU's gallery, file 'hm3x mount_1.JPG': the flip mount alone from above, its hinge at the right, 2200 px)","scaleRef":"the hinge block's length in the same photo (1208 px), 1.728 in by the side view: 699 px/in; by the mount's width in the drawing's end view (1.53 in from the lever's outer edge to the knuckle's outer face, 1097 px) it is 717 px/in, and the ± covers both","method":"each hole about 110 px across at its mouth","via":"harvest"}}]},"tool_knob_d":{"label":"The adjustment tool's knurled knob, across","kind":"length","measurements":[{"id":"side","value":0.3,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-hm3x eea64f6b7ff8 (holosun.com's gallery: the magnifier's right side, square on, 1000 px)","scaleRef":"holosun-hm3x.length across the picture (872 px: 216.4 px/in) and holosun-hm3x.eyepiece_ring_od upright in it (306 px: 215.5 px/in): one scale both ways, a view with no perspective to speak of","method":"rows 695 to 760 (65 px); from above it is 220 px across (0.31)","via":"harvest"}}],"note":"The manual's Figure 1 names it: the tool stowed in the mount under the hinge's rear end, its knob standing out to the rear."},"tool_knob_length":{"label":"The adjustment tool's knob, out of the rear knuckle's rear face","kind":"length","measurements":[{"id":"side","value":0.208,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-hm3x eea64f6b7ff8 (holosun.com's gallery: the magnifier's right side, square on, 1000 px)","scaleRef":"holosun-hm3x.length across the picture (872 px: 216.4 px/in) and holosun-hm3x.eyepiece_ring_od upright in it (306 px: 215.5 px/in): one scale both ways, a view with no perspective to speak of","method":"columns 490 to 535 (45 px)","via":"harvest"}}],"note":"Its rear end is the mount's: the drawing's rear extension line (half of mount_base_length behind the middle) is 0.969 behind by this picture."},"tool_knob_above_rail":{"label":"The adjustment tool's knob: its axis above the rail top","kind":"length","measurements":[{"id":"side","value":0.17,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/holosun-hm3x eea64f6b7ff8 (holosun.com's gallery: the magnifier's right side, square on, 1000 px)","scaleRef":"holosun-hm3x.length across the picture (872 px: 216.4 px/in) and holosun-hm3x.eyepiece_ring_od upright in it (306 px: 215.5 px/in): one scale both ways, a view with no perspective to speak of","method":"its middle at row 727.5: 0.157 from the knuckle's top, 0.183 from the jaws' bottom (see hinge_axis_above_rail)","via":"harvest"}}]},"tool_knob_right_of_centre":{"label":"The adjustment tool's knob: its axis right of the optical axis's vertical","kind":"length","measurements":[{"id":"plan","value":0.42,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-hm3x 9b4d7ab4e4c7 (Holosun EU's gallery, file 'hm3x mount_1.JPG': the flip mount alone from above, its hinge at the right, 2200 px)","scaleRef":"the hinge block's length in the same photo (1208 px), 1.728 in by the side view: 699 px/in; by the mount's width in the drawing's end view (1.53 in from the lever's outer edge to the knuckle's outer face, 1097 px) it is 717 px/in, and the ± covers both","method":"its middle at column 1430, 299 px right of the plate's centre pin: 0.428 and 0.417","via":"harvest"}}]},"hinge_cap_proud":{"label":"The hinge's rear end (the tension screw's boss), out of the rear knuckle's rear face","kind":"length","measurements":[{"id":"side","value":0.16,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-hm3x eea64f6b7ff8 (holosun.com's gallery: the magnifier's right side, square on, 1000 px)","scaleRef":"holosun-hm3x.length across the picture (872 px: 216.4 px/in) and holosun-hm3x.eyepiece_ring_od upright in it (306 px: 215.5 px/in): one scale both ways, a view with no perspective to speak of","method":"columns 500 to 535 (35 px), rows 625 to 700","via":"harvest"}}],"note":"The manual's Figure 1 names the slotted head in it the tension screw. As wide as the barrel in this view (75 px)."},"clamp_bolt_head_d":{"label":"The clamp's cross bolt: its head on the mount's right face, across","kind":"length","measurements":[{"id":"side","value":0.32,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-hm3x eea64f6b7ff8 (holosun.com's gallery: the magnifier's right side, square on, 1000 px)","scaleRef":"holosun-hm3x.length across the picture (872 px: 216.4 px/in) and holosun-hm3x.eyepiece_ring_od upright in it (306 px: 215.5 px/in): one scale both ways, a view with no perspective to speak of","method":"columns 688 to 757 (69 px)","via":"harvest"}}]},"clamp_bolt_behind_hinge_front":{"label":"The clamp's cross bolt, behind the hinge block's front end","kind":"length","measurements":[{"id":"side","value":0.864,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-hm3x eea64f6b7ff8 (holosun.com's gallery: the magnifier's right side, square on, 1000 px)","scaleRef":"holosun-hm3x.length across the picture (872 px: 216.4 px/in) and holosun-hm3x.eyepiece_ring_od upright in it (306 px: 215.5 px/in): one scale both ways, a view with no perspective to speak of","method":"its head's middle at column 722, the block's front at 909 (187 px)","via":"harvest"}}],"note":"At the rail top's level by the same picture (row 765: 0.017 under it from the knuckle's top, 0.010 over it from the jaws' bottom), under the middle of the barrel."},"objective_ring_flutes":{"label":"Objective ring: its flutes, counted round the whole turn","kind":"count","measurements":[{"id":"end","value":16,"unit":"count","source":{"type":"photo","photo":"references/holosun-hm3x 7994638176a5 (Holosun EU's gallery: the magnifier on its mount from the objective end, square on, 2200 px; a rendering from close by)","scaleRef":"none needed: a count. The outline unwrapped about the ring's centre (1094.9, 750.8; radius 377.1 px to the lands), .cache/detail/holosun-hm3x/unwrap.py and rim.py","method":"the outline's radius every half degree from 60 below the picture's right round over the top to 240 (the foot hides the rest): notches 5.9 px deep with their middles at -44.8, -22.2, 0.2, 22.5, 44.8, 64.8 and, past the top boss, 115, 134.5, 154, 180 degrees: one every 22.5 degrees, sixteen to the turn. Checked on the left side, which shows half the turn: the dark walls in Primary Arms' photo (7602cbc9ffbd, rows 234, 430, 554, 677 and 757 of a ring whose silhouette is rows 194.5 to 826) are at 61.0, 14.7, -8.0, -31.9 and -51.4 degrees above the axis, five flutes in 112.4 degrees: 22.5 apart (the wall between the first two doesn't show)","via":"harvest"}}],"note":"Wide and shallow, open at both ends of the ring: they notch its front rim, which is the outline of Holosun's view from the objective end, and its rear edge is scalloped by them in Primary Arms' photo of the left side (7602cbc9ffbd, columns 270 to 285). The ring doesn't turn; the notches stand at the top, the bottom and both sides. The manual's line drawings (its cover, Figures 1 and 8) draw both rings with many narrow flutes: an earlier drawing of the housing, not what the photos or the dimensioned drawing's side view have."},"objective_ring_flute_depth":{"label":"Objective ring: how deep its flutes are","kind":"length","measurements":[{"id":"end","value":0.0103,"unit":"in","pm":0.002,"source":{"type":"photo","photo":"references/holosun-hm3x 7994638176a5 (Holosun EU's gallery: the magnifier on its mount from the objective end, square on, 2200 px; a rendering from close by)","scaleRef":"holosun-hm3x.objective_ring_od (1.32 in) across the same rim, whose lands are 377.1 px from its centre: 571 px/in at the rim, where the notches are read","method":"the outline less a smooth curve through its lands (.cache/detail/holosun-hm3x/rim.py): each notch's floor is 5.8 to 6.1 px inside it, over nine notches (5.9: 0.0103 in). ± is half a pixel and the ring's diameter","via":"harvest"}}]},"objective_ring_flute_floor":{"label":"Objective ring: each flute's floor, as an angle round the axis","kind":"angle","measurements":[{"id":"end","value":8.5,"unit":"deg","pm":1,"source":{"type":"photo","photo":"references/holosun-hm3x 7994638176a5 (Holosun EU's gallery: the magnifier on its mount from the objective end, square on, 2200 px; a rendering from close by)","scaleRef":"the ring's own turn: angles about its centre (1094.9, 750.8), a degree being 6.6 px along the rim","method":"where the outline is level at the notch's depth: -26 to -18, -4 to 5, 18.5 to 27, 41 to 49.5 degrees; the lands level from -37 to -29.5, -15 to -7, 8 to 16, 30 to 38, 52 to 60","via":"harvest"}}],"note":"The lands between are as wide (8.5 degrees), and a sloping wall joins each floor to each land (objective_ring_flute_wall): 8.5 + 2.75 + 8.5 + 2.75 = 22.5 degrees, a sixteenth of the turn."},"objective_ring_flute_wall":{"label":"Objective ring: each flute's sloping wall, as an angle round the axis","kind":"angle","measurements":[{"id":"end","value":2.75,"unit":"deg","pm":0.75,"source":{"type":"photo","photo":"references/holosun-hm3x 7994638176a5 (Holosun EU's gallery: the magnifier on its mount from the objective end, square on, 2200 px; a rendering from close by)","scaleRef":"the ring's own turn: angles about its centre (1094.9, 750.8), a degree being 6.6 px along the rim","method":"the outline falls from a land to a floor over 2.5 to 3 degrees at each of eighteen walls (0.032 in along the rim for 0.010 in of depth: a slope of about 18 degrees, which is why the flutes are soft bands in the photos and not lines). Primary Arms' photo of the left side has one such wall as a dark band 12 px wide where this predicts 11.8 (7602cbc9ffbd, rows 428 to 440)","via":"harvest"}}]},"objective_ring_length":{"label":"Objective ring: its length along the axis","kind":"length","measurements":[{"id":"side","value":0.348,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/holosun-hm3x 7602cbc9ffbd (Primary Arms' HM3X_01.jpg: the left side, square on, 2200 px)","scaleRef":"the two rings in the same photo, upright in it: the eyepiece ring's silhouette rows 176.5 to 860.2 for holosun-hm3x.eyepiece_ring_od (481.5 px/in), the objective ring's 194.5 to 826 for holosun-hm3x.objective_ring_od (478.4)","method":"the ring's front rim at column 111.5 and the dark line at its rear edge at 278 (272 to 284) along rows 520 to 545: 166.5 px. Holosun's picture of the left side has it 73 px at 216 px/in (0.338), and the drawing's traced side outline from its shoulder 0.712 ahead of the mount's middle to its front face at 1.046 (0.334; the outline's corner there, where the drawing's extension lines meet it, reaches 1.065). The model's flutes run between the outline's own shoulder and face","via":"harvest"}}],"note":"From the housing's front face back to the ring's rear edge, where a neck a hundredth of an inch lower begins: the flutes run its whole length."},"eyepiece_ring_flutes":{"label":"Eyepiece (diopter) ring: its flutes, counted round the whole turn","kind":"count","measurements":[{"id":"side","value":14,"unit":"count","source":{"type":"photo","photo":"references/holosun-hm3x 7602cbc9ffbd (Primary Arms' HM3X_01.jpg: the left side, square on, 2200 px)","scaleRef":"none needed: a count. The ring's own silhouette, rows 176.5 to 860.2 (its axis at row 518.35, its radius 341.85 px), sets each row's angle","method":"the flutes' upper walls are sharp dark lines 4 to 5 px wide at rows 228.5, 335.5, 483 and 642: 58.0, 32.3, 5.9 and -21.2 degrees above the axis as read, 26.4 apart (the lit lower walls at rows 282.5, 418, 573.5 and 717.5 likewise). Fitted with the lens's distance left free (.cache/detail/holosun-hm3x/flutefit.py), fourteen flutes meet the four lines within 0.3 to 0.8 degrees, thirteen within 1.5 to 2.2 and fifteen within 1.2 to 2.7 (the best fit: fourteen with the lens about 24 in away, where the objective ring's sixteen, known from its end, read 23.3 degrees apart about its middle as they do: rows 430, 554, 677). The turn closes on a whole number","via":"harvest"}}],"note":"Fourteen, where the objective ring has sixteen. No picture on file looks straight at this ring's end, so it is counted on a side, which shows half the turn, by the angle between flutes: a row y of the ring is asin((y - yc) / R) round the axis. A photo from near enough reads what faces the lens a few per cent large against the silhouette, so the rows are tried against thirteen, fourteen and fifteen flutes with the lens anywhere from 12 in away to infinitely far: fourteen fits best at every distance. Holosun's own side pictures are taken from closer still and agree (26.5 to 27 degrees as read; never the objective ring's 22.5). The ring turns (the manual: \"Rotate the diopter adjustment with your thumb and forefinger\"); it is drawn as this photo has it, a flute at each side and a land at the top."},"eyepiece_ring_flute_width":{"label":"Eyepiece ring: each flute, as an angle round the axis at the ring's surface","kind":"angle","measurements":[{"id":"side","value":14.8,"unit":"deg","pm":1.2,"source":{"type":"photo","photo":"references/holosun-hm3x 7602cbc9ffbd (Primary Arms' HM3X_01.jpg: the left side, square on, 2200 px)","scaleRef":"the ring's own silhouette, rows 176.5 to 860.2 (its axis at row 518.35, its radius 341.85 px), sets each row's angle","method":"from each dark upper wall to the lit lower wall under it: rows 228.5 to 282.5 (58.0 to 43.6 degrees: 14.4), 335.5 to 418 (32.3 to 17.1: 15.3), 483 to 573.5 (5.9 to -9.3: 15.2); 15.0 as read, of 26.4 from flute to flute where fourteen flutes are 25.7 apart, so 14.6 to 15.0 of the turn's fourteenth. Holosun's picture of the left side has one from row 385 to 424 of a ring of radius 144.4 px (15.6 as read, from closer). ± covers the spread and a wall's own 4 to 5 px","via":"harvest"}}],"note":"Flat-floored pockets with steep walls, wider than the lands between them (10.9 degrees). Which is which: the photo is lit from above, and each wide band has a shadowed line along its upper edge and a lit one along its lower, as a recess has."},"eyepiece_ring_flute_end_inset":{"label":"Eyepiece ring: how far short of each end of the ring its flutes stop","kind":"length","measurements":[{"id":"side","value":0.03,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/holosun-hm3x 7602cbc9ffbd (Primary Arms' HM3X_01.jpg: the left side, square on, 2200 px)","scaleRef":"holosun-hm3x.eyepiece_ring_od upright in the same photo (683.7 px: 481.5 px/in)","method":"along rows 345 to 400 and 500 to 560, inside two flutes: the ring runs from column 1901 (the dark gap before it ends) to its rear rim at 2096; the flute's end walls are the lit lines at 1915 to 1918 and 2077 to 2083 (14 to 17 px from the one end, 13 to 19 from the other)","via":"harvest"}}],"note":"Closed at both ends, unlike the objective ring's: the ring's rear rim has no notch in it (its outline in Holosun's view from the rear right, d8dddfb5eb56, keeps within 0.1 px of a smooth curve over 115 degrees of the turn). So no edge shows how deep they are, and that is not read: they are drawn as deep as the objective ring's."},"eyepiece_ring_length":{"label":"Eyepiece ring: its length along the axis","kind":"length","measurements":[{"id":"side","value":0.405,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/holosun-hm3x 7602cbc9ffbd (Primary Arms' HM3X_01.jpg: the left side, square on, 2200 px)","scaleRef":"holosun-hm3x.eyepiece_ring_od upright in the same photo (683.7 px: 481.5 px/in)","method":"columns 1901 to 2096 along rows 345 to 400 (195 px). Holosun's picture of the left side has it 88 px at 216 px/in (0.407), and the drawing's traced side outline from 2.995 to 2.602 behind the mount's middle (0.393)","via":"harvest"}}]},"base_left_wall_left_of_centre":{"label":"The mount base's left face (the wall the lever lies along), left of the optical axis's vertical","kind":"length","measurements":[{"id":"drawing","value":0.604,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, end view)","scaleRef":"the end view's frame on its own dimension lines (214.4 px/in, rms 0.001 in: the trace's), its middle at column 1612.3","method":"the upright line the lever's ears stand on, columns 1741 to 1742 along rows 1224, 1247 and 1267 (1741.7). The same view's traced outline has the lever's own outer edge at 0.873","via":"harvest"}}]},"lever_pivot_ahead_of_centre":{"label":"The QD lever's pivot (the roller between its two ears), ahead of the mount's middle","kind":"length","measurements":[{"id":"drawing","value":0.097,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, side view)","scaleRef":"the side view's frame on its own dimension lines (214.1 px/in, rms 0.003 in: the trace's), the mount's middle at column 548.25","method":"the roller's two sides at columns 505.5 and 549.5 along row 1242: its middle at 527.5","via":"harvest"}}]},"lever_roller_d":{"label":"The QD lever's roller, across","kind":"length","measurements":[{"id":"drawing","value":0.206,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, side view)","scaleRef":"the side view's frame on its own dimension lines (214.1 px/in, rms 0.003 in: the trace's), the mount's middle at column 548.25","method":"columns 505.5 to 549.5 along row 1242 (44 px)","via":"harvest"}}],"note":"Bright steel in Holosun's pictures (a dark grey bush in Primary Arms'), upright between the lever's two ears; the clamp's cross bolt ends in it."},"lever_roller_top_above_rail":{"label":"The QD lever's roller: its top (the upper ear's underside) above the rail top","kind":"length","measurements":[{"id":"drawing","value":0.073,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, side view)","scaleRef":"the side view's frame on its own dimension lines (214.1 px/in, rms 0.003 in: the trace's), the rail top at row 1247.19","method":"the line at rows 1230 to 1233 down columns 520 and 545 (1231.5); the end view has the same line at the same rows","via":"harvest"}}]},"lever_roller_bottom_below_rail":{"label":"The QD lever's roller: its bottom (the lower ear's top) below the rail top","kind":"length","measurements":[{"id":"drawing","value":0.036,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, side view)","scaleRef":"the side view's frame on its own dimension lines (214.1 px/in, rms 0.003 in: the trace's), the rail top at row 1247.19","method":"the line at rows 1252 to 1256 down columns 520 and 545 (1255); the end view has the same line at the same rows","via":"harvest"}}]},"lever_ear_d":{"label":"The QD lever's two ears about its pivot, across","kind":"length","measurements":[{"id":"below","value":0.19,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-hm3x 3bcb120eaf6e (Holosun EU's gallery: the magnifier on its mount from below, the objective end down, 2200 px)","scaleRef":"the rail channel's roof in the same photo, columns 985 to 1310 (325 px) for the 0.653 in the drawing's traced end outline has between its two edges: 498 px/in; the jaws' underside front to rear (rows 990 to 1770 for the traced side outline's 1.546 in) gives 504","method":"the pivot pin's middle at column 748 and the ear's outer edge at 700 along row 1345: 48 px, doubled. The picture of the mount from above (9b4d7ab4e4c7) has 65 px from the pin's middle to the ear's edge at about 705 px/in (0.184 across)","via":"harvest"}}],"note":"Round about the pivot pin from below and from above. The ears' outer end is the mount's left extreme: 0.877 in left of the middle here, 0.873 in the drawing's traced end outline. That drawing's end view has the ears' lines from column 1750.5 to 1798 (0.222 in): more than the round, the ears running on inboard toward the clamp's nose."},"lever_top_above_rail":{"label":"The QD lever's upper edge above the rail top","kind":"length","measurements":[{"id":"drawing","value":0.203,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, side view)","scaleRef":"the side view's frame on its own dimension lines (214.1 px/in, rms 0.003 in: the trace's), the rail top at row 1247.19","method":"the line along the lever at rows 1203 to 1204.5 down columns 495 to 695 (1203.75)","via":"harvest"}}]},"lever_bottom_below_rail":{"label":"The QD lever's lower edge below the rail top","kind":"length","measurements":[{"id":"drawing","value":0.163,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, side view)","scaleRef":"the side view's frame on its own dimension lines (214.1 px/in, rms 0.003 in: the trace's), the rail top at row 1247.19","method":"the line along the lever at rows 1281.5 to 1282.5 down columns 495 to 660 (1282)","via":"harvest"}}]},"lever_rear_behind_centre":{"label":"The QD lever's rear end (its ribbed pad's), behind the mount's middle","kind":"length","measurements":[{"id":"drawing","value":0.91,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, side view)","scaleRef":"the side view's frame on its own dimension lines (214.1 px/in, rms 0.003 in: the trace's), the mount's middle at column 548.25","method":"the pad's dark run ends at column 742 along row 1270 and 743 along 1242 (743)","via":"harvest"}}],"note":"Past the base's rear face (0.765 behind) by 0.145 in: the pad is what a thumb takes."},"lever_pad_length":{"label":"The QD lever's ribbed pad, along the lever","kind":"length","measurements":[{"id":"drawing","value":0.206,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, side view)","scaleRef":"the side view's frame on its own dimension lines (214.1 px/in, rms 0.003 in: the trace's), the mount's middle at column 548.25","method":"the ribs begin at column 699 (rows 1215 to 1270) and the pad ends at 743: 44 px","via":"harvest"}}],"note":"Its ribs run across the lever, seven grooves 0.029 in apart in Holosun's picture of the left side (5ee8dd2e6815, columns 460 to 498 along rows 728 to 760: a groove 0.012 in wide). Finer than a page draws: the pad is drawn plain."},"lever_arm_thickness":{"label":"The QD lever's arm, across (how thick it is, seen from above or below)","kind":"length","measurements":[{"id":"below","value":0.09,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/holosun-hm3x 3bcb120eaf6e (Holosun EU's gallery: the magnifier on its mount from below, the objective end down, 2200 px)","scaleRef":"the rail channel's roof in the same photo, columns 985 to 1310 (325 px) for the 0.653 in the drawing's traced end outline has between its two edges: 498 px/in; the jaws' underside front to rear (rows 990 to 1770 for the traced side outline's 1.546 in) gives 504","method":"along row 1100 the arm's lit face is columns 743 to 777 and its shaded inner edge runs to 790 (34 to 47 px: 0.07 to 0.095 in). The picture of the mount from above (9b4d7ab4e4c7) has it 82 px along row 1320 at about 705 px/in (0.116), the lever standing open there and seen aslant. ± covers the three","via":"harvest"}}]},"lever_tip_outer_from_wall":{"label":"The QD lever's rear end: its outer face, out from the base's left wall","kind":"length","measurements":[{"id":"below","value":0.18,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-hm3x 3bcb120eaf6e (Holosun EU's gallery: the magnifier on its mount from below, the objective end down, 2200 px)","scaleRef":"the rail channel's roof in the same photo, columns 985 to 1310 (325 px) for the 0.653 in the drawing's traced end outline has between its two edges: 498 px/in; the jaws' underside front to rear (rows 990 to 1770 for the traced side outline's 1.546 in) gives 504","method":"the arm's outer edge at column 751.5 along row 1020, and the base's side at column 839 (the front block's face, 836 to 842, which is the wall: 0.604 in left of the middle at this scale): 87.5 px","via":"harvest"}}],"note":"Less than at the pivot (0.27 in, the ears' outer end in the drawing's end view): closed, the arm leans in toward the base and lies on the catch block behind it (lever_catch_proud + lever_arm_thickness = 0.175)."},"lever_catch_length":{"label":"The block on the base's left wall that the lever's rear end latches on: its length along the rail","kind":"length","measurements":[{"id":"below","value":0.36,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/holosun-hm3x 3bcb120eaf6e (Holosun EU's gallery: the magnifier on its mount from below, the objective end down, 2200 px)","scaleRef":"the rail channel's roof in the same photo, columns 985 to 1310 (325 px) for the 0.653 in the drawing's traced end outline has between its two edges: 498 px/in; the jaws' underside front to rear (rows 990 to 1770 for the traced side outline's 1.546 in) gives 504","method":"its face down columns 855 to 865: rows 993 to 1173 (180 px)","via":"harvest"}}],"note":"From the base's rear end forward. Behind the closed lever from the side; Primary Arms' photo, with the lever swung open, has it in the open, with the screw in its face."},"lever_catch_proud":{"label":"The lever's catch block: how far it stands out of the base's left wall","kind":"length","measurements":[{"id":"below","value":0.085,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-hm3x 3bcb120eaf6e (Holosun EU's gallery: the magnifier on its mount from below, the objective end down, 2200 px)","scaleRef":"the rail channel's roof in the same photo, columns 985 to 1310 (325 px) for the 0.653 in the drawing's traced end outline has between its two edges: 498 px/in; the jaws' underside front to rear (rows 990 to 1770 for the traced side outline's 1.546 in) gives 504","method":"its outer face at column 800 along row 1100, and the base's side at column 839 (the front block's face): 39 to 42 px; the lever's arm lies against it","via":"harvest"}}]},"lever_recess_length":{"label":"The recess in the lever's outer face (the lever lock's screw is in it): its length along the lever","kind":"length","measurements":[{"id":"drawing","value":0.32,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, side view)","scaleRef":"the side view's frame on its own dimension lines (214.1 px/in, rms 0.003 in: the trace's), the mount's middle at column 548.25","method":"its two ends at columns 622.5 and 691 along row 1242 (68.5 px): from 0.347 to 0.667 behind the mount's middle","via":"harvest"}}],"note":"The manual's Figure 5: \"Press the lever lock forward and release the QD lever\". How deep the recess is isn't read."},"lever_recess_height":{"label":"The recess in the lever's outer face: its height","kind":"length","measurements":[{"id":"drawing","value":0.173,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, side view)","scaleRef":"the side view's frame on its own dimension lines (214.1 px/in, rms 0.003 in: the trace's), the rail top at row 1247.19","method":"rows 1224.5 to 1261.5 down column 640 (37 px), its middle at row 1243: 0.02 in above the rail top, the roller's own middle","via":"harvest"}}]},"lever_recess_behind_centre":{"label":"The recess in the lever's outer face: its middle, behind the mount's middle","kind":"length","measurements":[{"id":"drawing","value":0.507,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, side view)","scaleRef":"the side view's frame on its own dimension lines (214.1 px/in, rms 0.003 in: the trace's), the mount's middle at column 548.25","method":"midway between its ends at columns 622.5 and 691 (656.75)","via":"harvest"}}]},"lever_screw_d":{"label":"The socket screw in the lever's recess: its head, across","kind":"length","measurements":[{"id":"drawing","value":0.15,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, side view)","scaleRef":"the side view's frame on its own dimension lines (214.1 px/in, rms 0.003 in: the trace's), the mount's middle at column 548.25","method":"its outer circle crosses column 660 at rows 1227 and 1259 (32 px); its middle at column 665, 0.545 in behind the mount's middle (0.038 behind the recess's)","via":"harvest"}}],"note":"A bright socket head in Holosun's picture of the left side, toward the recess's rear end."},"lever_screw_behind_centre":{"label":"The socket screw in the lever's recess: its middle, behind the mount's middle","kind":"length","measurements":[{"id":"drawing","value":0.545,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, side view)","scaleRef":"the side view's frame on its own dimension lines (214.1 px/in, rms 0.003 in: the trace's), the mount's middle at column 548.25","method":"its circles' middle at column 665 along row 1242 (the outer one from 645 to 684.5), level with the recess's middle","via":"harvest"}}]},"lever_link_ahead_of_centre":{"label":"The slotted link ahead of the lever's ears: its middle, ahead of the mount's middle","kind":"length","measurements":[{"id":"drawing","value":0.38,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, side view)","scaleRef":"the side view's frame on its own dimension lines (214.1 px/in, rms 0.003 in: the trace's), the mount's middle at column 548.25","method":"its two sides at columns 457 and 477 along rows 1242 and 1270 (467)","via":"harvest"}}],"note":"An upright strip with a slot down it, in the base's side ahead of the lever (a spring shows in the slot's foot in the drawing). How thick it is isn't read."},"lever_link_width":{"label":"The slotted link: its width along the rail","kind":"length","measurements":[{"id":"drawing","value":0.093,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, side view)","scaleRef":"the side view's frame on its own dimension lines (214.1 px/in, rms 0.003 in: the trace's), the mount's middle at column 548.25","method":"columns 457 to 477 (20 px); the slot in it columns 465 to 472.5 (0.035 in, a little over a third of it), from row 1222 to 1280","via":"harvest"}}]},"lever_link_height":{"label":"The slotted link: its height","kind":"length","measurements":[{"id":"drawing","value":0.332,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, side view)","scaleRef":"the side view's frame on its own dimension lines (214.1 px/in, rms 0.003 in: the trace's), the rail top at row 1247.19","method":"rows 1212 to 1283 down column 475 (71 px): from 0.164 above the rail top to 0.167 below it, its middle level with the rail top","via":"harvest"}}]},"clamp_nose_width":{"label":"The clamp's nose between the base's left wall and the lever's roller: its width along the rail where it meets the wall","kind":"length","measurements":[{"id":"plan","value":0.445,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-hm3x 9b4d7ab4e4c7 (Holosun EU's gallery, file 'hm3x mount_1.JPG': the flip mount alone from above, its hinge at the right, 2200 px)","scaleRef":"the hinge block's length in the same photo (1208 px), 1.728 in by the side view: 699 px/in; by the mount's width in the drawing's end view (1.53 in from the lever's outer edge to the knuckle's outer face, 1097 px) it is 717 px/in, and the ± covers both","method":"along the base's left edge, column 745: rows 925 to 1240 (315 px)","via":"harvest"}}],"note":"The moving jaw's wedge, which the lever's ears bear on: it narrows from the wall to the roller (to 0.2 in: rows 1010 to 1150 at column 640). As tall as the roller where the drawing's side view shows it beside the roller (columns 549.5 to 567.5, rows 1230 to 1255)."},"base_strip_screw_spacing":{"label":"The strip let into the mount base's top under the flip plate: its two screws, apart along the rail","kind":"length","measurements":[{"id":"fig4","value":0.79,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/holosun-hm3x docs/5e8eadd6c5.pdf (Holosun's HM3X manual V2.2, page 1, Figure 4: the mount from the front left and above, the flip plate standing; vector art, read at 900 dpi)","scaleRef":"the flip plate's own two screw holes in the same figure, 146.8 px apart along the same direction, for holosun-hm3x.flip_plate_screw_spacing (0.69 in)","method":"the two screws' middles 168.3 px apart, parallel to the holes within a degree. Figure 3 has them 0.435 of the base's top face's left edge apart: 0.75 in by holosun-hm3x.base_plate_length","via":"harvest"}}],"note":"The manual's Figures 3 and 4 draw it in the base's top face between the knuckles, a bar with a screw at each end in a shallow pocket; what it does isn't said (it lies where a detent for the flip plate would). No photo on file shows the base's top with the plate swung off it."},"base_strip_length":{"label":"The strip in the mount base's top: its length along the rail","kind":"length","measurements":[{"id":"fig3","value":1,"unit":"in","pm":0.07,"source":{"type":"photo","photo":"references/holosun-hm3x docs/5e8eadd6c5.pdf (Holosun's HM3X manual V2.2, page 1, Figure 3: the mount from the rear left and above, the magnifier swung aside; vector art, read at 900 dpi)","scaleRef":"the strip's own two screws in the same figure, 201.8 px apart, for holosun-hm3x.base_strip_screw_spacing","method":"the pocket's long side 254.6 px, a screw head's half width past each screw: 1.26 of their spacing. Its near end is at the rear knuckle's front face","via":"harvest"}}]},"base_strip_width":{"label":"The strip in the mount base's top: its width across the rail","kind":"length","measurements":[{"id":"fig3","value":0.16,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/holosun-hm3x docs/5e8eadd6c5.pdf (Holosun's HM3X manual V2.2, page 1, Figure 3: the mount from the rear left and above, the magnifier swung aside; vector art, read at 900 dpi)","scaleRef":"the base's top face across the rail in the same figure, 561 px along its rear edge from its left edge to the knuckles' inner face, for the 0.778 in between the drawing's end view's left edge (0.563) and holosun-hm3x.hinge_knuckle_inner_right_of_centre: 721 px/in across","method":"the bar the two screws are in, 115 px across the rail","via":"harvest"}}]},"base_strip_right_of_centre":{"label":"The strip in the mount base's top: its middle, right of the optical axis's vertical","kind":"length","measurements":[{"id":"fig3","value":0.045,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/holosun-hm3x docs/5e8eadd6c5.pdf (Holosun's HM3X manual V2.2, page 1, Figure 3: the mount from the rear left and above, the magnifier swung aside; vector art, read at 900 dpi)","scaleRef":"the base's top face across the rail in the same figure, 561 px along its rear edge from its left edge to the knuckles' inner face, for the 0.778 in between the drawing's end view's left edge (0.563) and holosun-hm3x.hinge_knuckle_inner_right_of_centre: 721 px/in across","method":"the bar's left edge, carried along the rail's direction to the top face's rear edge, meets it 381 px from its left end (0.035 in left of the middle); the bar is 115 px wide","via":"harvest"}}],"note":"On the rail's middle line within the reading: under the flip plate's own two screws."},"tension_screw_slot_width":{"label":"The tension screw's slot (in the hinge's rear end), across","kind":"length","measurements":[{"id":"fig3","value":0.064,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/holosun-hm3x docs/5e8eadd6c5.pdf (Holosun's HM3X manual V2.2, page 1, Figure 3: the mount from the rear left and above, the magnifier swung aside; vector art, read at 900 dpi)","scaleRef":"the slotted head's own circle in the same figure, 285 px upright, for holosun-hm3x.hinge_barrel_d (0.35 in: the head is as wide as the barrel in Holosun's picture of the right side)","method":"the slot's two edges 52 px apart at the circle's middle: 0.18 of the head","via":"harvest"}}],"note":"The manual's Figure 1 names the slotted head the tension screw; its Figures 3, 5 and 7 draw the slot level, across the rifle. How deep it is isn't read."},"adjuster_cap_d":{"label":"The two adjusters' caps (on top of the housing and on its right flank), across","kind":"length","measurements":[{"id":"drawing","value":0.63,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, end view, seen from the objective end)","scaleRef":"the end view's frame on its own dimension lines (214.7 px/in: the axis at row 944.5, the rail top at 1247.19 for holosun-hm3x.optical_axis_above_rail_no_spacer; the axis's vertical at column 1612.3)","method":"the top lug's two sides at columns 1544.5 and 1680 on rows 780 to 795 (135.5 px); the side lug's two ends at rows 877 and 1012 down column 1446 (135 px, its middle on the axis's row). The side view has the top cap's face 138 px long on row 777 (columns 574 to 712: 0.646 in with its corners' breaks)","via":"harvest"}}],"note":"The drawing's end view has two lugs of one size on the housing, one on top and one on the rifle's right, each as far from the axis as the other: the two adjusters' round caps (Holosun's pictures of the right side and from either end have both, each with a coin slot). Holosun's picture of the right side has the flank's cap 140 px across its rim where the housing is 872 px long (0.647 in: it is on the near flank and reads a little large)."},"side_cap_face_right_of_axis":{"label":"The right flank's adjuster cap: its face, right of the optical axis","kind":"length","measurements":[{"id":"drawing","value":0.786,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, end view, seen from the objective end: the picture's left is the rifle's right)","scaleRef":"the end view's frame on its own dimension lines (214.7 px/in), the axis's vertical at column 1612.3","method":"the lug's outer face, a line at columns 1443 to 1446 on rows 920 to 970 (its outer edge 1443.5): 168.8 px from the axis","via":"harvest"}}],"note":"As far from the axis as the top cap's face is above it (holosun-hm3x.top_above_rail_no_spacer less the axis's height: 0.79)."},"side_cap_ahead_of_top_cap":{"label":"The right flank's adjuster cap: its middle, ahead of the top cap's along the housing","kind":"length","measurements":[{"id":"right","value":0.01,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-hm3x eea64f6b7ff8 (holosun.com 01: the right side, 1000 px, taken from about 14 degrees above: the top cap's face shows as an ellipse)","scaleRef":"holosun-hm3x.length (4.03 in) across the same picture, columns 63 to 935 on rows 440 to 460: 216.4 px/in along the housing, which the camera's height doesn't change","method":"along row 497 the flank's cap has its rim at columns 534 and 674, the black groove inside it at 551.5 and 659 and its inner cap's edge at 566.5 and 642.5: its middle 604.6. The top cap's face is columns 534 to 666 on row 282: its middle 600. 4.6 px is 0.021 in, less 0.007 to 0.013 for the flank's cap standing 0.79 in nearer a lens 30 to 60 in away and 105 px off the picture's middle","via":"harvest"}}],"note":"The two caps are in one plane across the housing, within the reading."},"adjuster_cap_slot_length":{"label":"An adjuster cap's coin slot, along","kind":"length","measurements":[{"id":"right","value":0.22,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-hm3x eea64f6b7ff8 (holosun.com 01: the right side, 1000 px, from about 14 degrees above)","scaleRef":"the flank's cap's own rim in its plane, 140 px across on row 497, for holosun-hm3x.adjuster_cap_d","method":"the slot's dark run down column 605, rows 476 to 522 (47 px upright, which the camera's height shortens by 3%)","via":"harvest"}}],"note":"Each cap has one, turned however its adjuster stands: drawn along the housing on the top cap and upright on the flank's, as Holosun's picture of the right side has them within 15 degrees. How deep it is isn't read."},"adjuster_cap_slot_width":{"label":"An adjuster cap's coin slot, across","kind":"length","measurements":[{"id":"right","value":0.06,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/holosun-hm3x eea64f6b7ff8 (holosun.com 01: the right side, 1000 px, from about 14 degrees above)","scaleRef":"the flank's cap's own rim in its plane, 140 px across on row 497, for holosun-hm3x.adjuster_cap_d","method":"the slot's dark pill is 13 px across square to its length (it leans 15 degrees in the picture: columns 590 to 611 where row 497 crosses it aslant)","via":"harvest"}}]},"logo_oval_length":{"label":"The HOLOSUN oval on the left flank: its length along the housing","kind":"length","measurements":[{"id":"drawing","value":1.239,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, side view: the left side)","scaleRef":"the side view's frame on its own dimension lines (213.5 px/in along: the base's two extension lines at columns 342.19 and 754.31 for holosun-hm3x.mount_base_length)","method":"the oval's outer line along row 944: columns 515 and 779.5 (264.5 px)","via":"harvest"}}],"note":"A rounded-ended oval with the maker's name in it (the letters aren't drawn). Primary Arms' photo of the left side has it 600 px long inside its rim at 479 px/in (1.25 in, on the near flank)."},"logo_oval_height":{"label":"The HOLOSUN oval on the left flank: its height","kind":"length","measurements":[{"id":"drawing","value":0.31,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, side view: the left side)","scaleRef":"the drawing's frame on its own dimension lines (214.7 px/in upright), the axis at row 944.5","method":"the oval's outer line down columns 560, 648 and 740: rows 911 and 977 (66 px: 0.307 in). The end view has the same thing edge on over rows 910.7 to 978.3 (0.315 in)","via":"harvest"}}],"note":"Its middle is on the optical axis's row in both of the drawing's views."},"logo_oval_behind_top_cap":{"label":"The HOLOSUN oval on the left flank: its middle, behind the top cap's along the housing","kind":"length","measurements":[{"id":"drawing","value":0.02,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, side view: the left side, the objective at the picture's left)","scaleRef":"the side view's frame on its own dimension lines (213.5 px/in along)","method":"the oval's middle at column 647.25 (its ends 515 and 779.5), the top cap's face's at 643 (columns 574 to 712 on row 777): 4.25 px toward the eyepiece","via":"harvest"}}],"note":"Under the top cap, within the reading. Holosun's picture of the left side (5ee8dd2e6815, 208.7 px/in: the housing is columns 94 to 935) has the oval's ends at columns 286 and 545 (1.241 in long, middle 415.5) and the top cap's face at 351 to 481 (middle 416): the two middles within 0.01 in once the near flank's 2% is allowed for."},"logo_oval_face_left_of_axis":{"label":"The HOLOSUN oval on the left flank: how far its face stands from the optical axis","kind":"length","measurements":[{"id":"drawing","value":0.739,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, end view, seen from the objective end: the picture's right is the rifle's left)","scaleRef":"the end view's frame on its own dimension lines (214.7 px/in), the axis's vertical at column 1612.3","method":"the bump's outer edge at column 1771 on rows 921 to 968 (column 1770 is dark over those rows, 1772 white): 158.7 px from the axis; its ends at rows 910.7 and 978.3","via":"harvest"}}],"note":"The relief read where it meets an edge: the drawing's end view has, on the rifle's left at the axis's height and over the oval's own height, a flat-faced bump standing past the housing's round (the round's widest is 0.72 to 0.73 in from the axis by the side view's top edge either side of the top boss). The photos have the oval's field sunk inside its edge (a shaded band inside the edge all round, a lit line outside it: Primary Arms' photo of the left side, Holosun's of the right): read together, a raised oval rim round a field at about the housing's own surface. That the two are one thing is this reading, not a view of it."},"logo_oval_rim":{"label":"The HOLOSUN oval: the width of the rim round its sunk field","kind":"length","measurements":[{"id":"left","value":0.02,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/holosun-hm3x 7602cbc9ffbd (Primary Arms: the left side, 2200 px)","scaleRef":"479 px/in, the scale the photo's rings were read at (holosun-hm3x.objective_ring_od across rows 194.5 to 826), 2% large on the near flank","method":"the shaded band inside the oval's edge: rows 460 to 473 down columns 750, 850 and 950 at its top (13 px), columns 545 to 551 along row 530 at its left end (6 px), each with a lit line 4 to 6 px outside it: 0.013 to 0.027 in","via":"harvest"}}],"note":"How far the field is sunk inside the rim isn't read: drawn down to the housing's own round at the oval's middle."},"right_logo_oval_length":{"label":"The HOLOSUN oval on the right flank: its length along the housing","kind":"length","measurements":[{"id":"right","value":1,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-hm3x eea64f6b7ff8 (holosun.com 01: the right side, 1000 px, from about 14 degrees above)","scaleRef":"holosun-hm3x.length (4.03 in) across the same picture, columns 63 to 935: 216.4 px/in along the housing at the axis's depth, up to 2% more on the near flank","method":"the oval's ends along row 495: the shaded line at column 252 and the lit one at 466 to 469 (216.7 px)","via":"harvest"}}],"note":"Smaller than the left flank's, and behind the adjuster's cap, toward the eyepiece. Whether it stands off the housing as the left one does isn't seen (the drawing's end view has the cap in front of it): drawn standing as far off the housing's round as the left one."},"right_logo_oval_height":{"label":"The HOLOSUN oval on the right flank: its height","kind":"length","measurements":[{"id":"right","value":0.245,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-hm3x eea64f6b7ff8 (holosun.com 01: the right side, 1000 px, from about 14 degrees above)","scaleRef":"216.4 px/in (holosun-hm3x.length across the same picture), the flank at the axis's height turned 14 degrees from the camera","method":"the oval's edges down columns 300, 360 and 420: rows 468 to 470 and 517 to 520 (50 px, 0.23 in as seen; 3% more square on, and the same shape as the left flank's oval, 4.0 to 1, would be 0.25)","via":"harvest"}}]},"right_logo_oval_behind_side_cap":{"label":"The HOLOSUN oval on the right flank: its middle, behind the adjuster cap's along the housing","kind":"length","measurements":[{"id":"right","value":1.12,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/holosun-hm3x eea64f6b7ff8 (holosun.com 01: the right side, 1000 px, from about 14 degrees above)","scaleRef":"216.4 px/in (holosun-hm3x.length across the same picture), up to 2% more on the near flank, where both are","method":"the oval's middle at column 360.5 (its ends 252 and 469), the cap's at 604.6: 244.1 px, 1.128 in at the axis's scale and 1.11 at the flank's","via":"harvest"}}]},"foot_rib_count":{"label":"The slanted pockets in each side of the magnifier's foot","kind":"count","measurements":[{"id":"drawing","value":5,"unit":"count","source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, side view: the left side, the objective at the picture's left)","scaleRef":"none needed: a count","method":"along row 1100 the pockets' walls are at columns 437 and 464.5, 479 and 506.5, 521.5 and 549, 564 and 590.5, and the fifth's front wall at 608 with the foot's rear wall at 625 behind it","via":"harvest"}}],"note":"Four whole ones and a fifth, rearmost, cut short by the foot's rear end (foot_rib_rear_wall_behind_base_centre). On both sides: Holosun's picture of the right side (eea64f6b7ff8) has five between the housing and the hinge's barrel, the four whole ones' dark walls at columns 781.5, 739, 697 and 655.5 on row 611 of a picture at 216.4 px/in (42 px apart: 0.194 in) and a short one behind them at columns 624 to 635, leaning the same way (tops toward the objective); so has Primary Arms' photo of the left side (7602cbc9ffbd: four and a short fifth). Sunk, not raised: in the right side's picture, lit from the left, each has a dark wall at its left and a lit one at its right, where the flank's cap, which stands out, is lit at its left; Primary Arms' photo, lit from above, has each one's upper edge dark and its lower corner lit."},"foot_rib_pitch":{"label":"The foot's slanted pockets: from one to the next along the housing","kind":"length","measurements":[{"id":"drawing","value":0.198,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, side view)","scaleRef":"the side view's frame on its own dimension lines (213.5 px/in along)","method":"the four front walls along row 1100 at columns 437, 479, 521.5 and 564: 42, 42.5 and 42.5 px apart (42.3)","via":"harvest"}}]},"foot_rib_width":{"label":"The foot's slanted pockets: each one's width along the housing (wall to wall along a level line)","kind":"length","measurements":[{"id":"drawing","value":0.128,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, side view)","scaleRef":"the side view's frame on its own dimension lines (213.5 px/in along)","method":"between the middles of each pocket's two drawn walls along row 1100: 27.5, 27.5, 27.5 and 26.5 px (the lines are 3 to 4 px thick: ± covers which edge of a line is the wall)","via":"harvest"}}]},"foot_rib_lean":{"label":"The foot's slanted pockets: how far their walls lean from upright, their tops toward the objective","kind":"angle","measurements":[{"id":"drawing","value":30,"unit":"deg","pm":3,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, side view)","scaleRef":"the drawing's own rows and columns (214.7 px/in upright, 213.5 along)","method":"the first pocket's front wall is at columns 432 to 435 on row 1094 and 449 to 453 on row 1124: 17.5 px along in 30 rows (30.2 degrees); the others run parallel to it (rows 1094 to 1124 of each)","via":"harvest"}}]},"foot_rib_first_front_ahead_of_base_centre":{"label":"The foot's slanted pockets: the first one's front wall at the pockets' bottom line, ahead of the mount base's centre","kind":"length","measurements":[{"id":"drawing","value":0.438,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, side view)","scaleRef":"the side view's frame on its own dimension lines (213.5 px/in along), the base's front extension line at column 342.19 for half of holosun-hm3x.mount_base_length","method":"the wall's line (column 437 on row 1100, leaning 0.583 px a row) carried down to the bottom line, row 1130.5: column 454.8, 112.6 px behind the base's front","via":"harvest"}}],"note":"The first is the one nearest the objective; the others follow it rearward at foot_rib_pitch."},"foot_rib_bottom_above_interface":{"label":"The foot's slanted pockets: their bottom line above the foot's underside (the face the spacer goes in at)","kind":"length","measurements":[{"id":"drawing","value":0.104,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, side view; it has no spacer)","scaleRef":"the drawing's frame on its own dimension lines (214.7 px/in upright), the interface's line at row 1152.84","method":"all four pockets' lower ends are on row 1130 to 1131 (the dark runs along row 1130 between columns 454 and 603): 22.3 px above the interface","via":"harvest"}}]},"foot_rib_top_above_interface":{"label":"The foot's slanted pockets: their top line above the foot's underside, over the first pocket's front wall's foot","kind":"length","measurements":[{"id":"drawing","value":0.31,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, side view)","scaleRef":"the drawing's frame on its own dimension lines (214.7 px/in upright), the interface's line at row 1152.84","method":"the pockets' upper edges down columns 445 to 448, 487 to 490, 530 to 533, 573 to 576 and 618 to 621: rows 1085.5, 1089, 1092, 1096 and 1099.5, one line falling 0.081 px a column; at column 454.8 it is at row 1086.3, 66.6 px above the interface. The housing's lower line is 12.5 to 13 px above it at each","via":"harvest"}}],"note":"The tops aren't level: they follow the housing's underside, a sixteenth of an inch under it, and fall toward the eyepiece (foot_rib_top_fall)."},"foot_rib_top_fall":{"label":"The foot's slanted pockets: how far their top line falls toward the eyepiece, as an angle from level","kind":"angle","measurements":[{"id":"drawing","value":4.7,"unit":"deg","pm":1,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, side view)","scaleRef":"the drawing's own rows and columns","method":"the five upper edges (rows 1085.5, 1089, 1092, 1096, 1099.5 at columns 446.5, 488.5, 531.5, 574.5, 619.5): 14 rows in 173 columns","via":"harvest"}}]},"foot_rib_rear_wall_behind_base_centre":{"label":"The foot's slanted pockets: the upright wall that cuts the fifth one short, behind the mount base's centre","kind":"length","measurements":[{"id":"drawing","value":0.359,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/holosun-hm3x 1fac54f9923c (Holosun's dimensioned drawing, side view)","scaleRef":"the side view's frame on its own dimension lines (213.5 px/in along), the base's front extension line at column 342.19","method":"the upright line at columns 624 to 626 on rows 1100 to 1124, behind the fifth pocket's leaning front wall (column 608 on row 1100, 618 on row 1124): 282.8 px behind the base's front","via":"harvest"}}]},"detail_relief":{"label":"How far the shallow pieces no view shows in profile are sunk (the foot's slanted pockets)","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the least the page draws (docs/research/model-detail-pass-2026-10-12.md), as holosun-aro.detail_relief is. That the pockets are sunk is read (foot_rib_count); how deep isn't seen in any view on file.","via":"harvest"}}]}}},{"subject":"holosun-hs510c","title":"Holosun HS510C Open Reflex MRS Solar QD Mount","dimensions":{"length":{"label":"Overall length","kind":"length","measurements":[{"id":"drawing","value":3.3,"unit":"in","pm":0.005,"stated":"3.30 in","source":{"type":"spec","publisher":"manufacturer","name":"Holosun Europe, HS510C (article 70127430): the dimensioned drawing in the page's gallery (side view from the right, end view from the front)","url":"https://www.holosun.eu/media/57/4c/a2/1713444013/2225a2021b0d4cf7ba373fc52f3fb238.jpg","retrieved":"2026-10-06","via":"harvest"}},{"id":"us","value":3.3,"unit":"in","pm":0.05,"stated":"Dimension (in) Body 3.3\" x 1.68\" x 1.78\"","source":{"type":"spec","publisher":"manufacturer","name":"Holosun, HS510C Open Reflex MRS Solar QD Mount, Specs (PHYSICAL DATA)","url":"https://www.holosun.com/products/hs510c","retrieved":"2026-10-06","via":"harvest"}},{"id":"eu","value":84,"unit":"mm","pm":0.5,"stated":"Size: 84x45x59 mm","source":{"type":"spec","publisher":"manufacturer","name":"Holosun Europe, HS510C open reflex red dot sight (article 70127430), Mechanical Parameters","url":"https://www.holosun.eu/en/p/70127430","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"drawing","reason":"Holosun's dimensioned drawing says between which lines; the two pages' figures agree with it."},"note":"The housing's rear end to its front face (the drawing's extension lines stand at those two); the mount and its lever are inside it."},"width":{"label":"Overall width (over the QD lever)","kind":"length","measurements":[{"id":"drawing","value":1.8,"unit":"in","pm":0.005,"stated":"1.80 in","source":{"type":"spec","publisher":"manufacturer","name":"Holosun Europe, HS510C (article 70127430): the dimensioned drawing in the page's gallery (side view from the right, end view from the front)","url":"https://www.holosun.eu/media/57/4c/a2/1713444013/2225a2021b0d4cf7ba373fc52f3fb238.jpg","retrieved":"2026-10-06","via":"harvest"}},{"id":"eu","value":45,"unit":"mm","pm":0.5,"stated":"Size: 84x45x59 mm","source":{"type":"spec","publisher":"manufacturer","name":"Holosun Europe, HS510C open reflex red dot sight (article 70127430), Mechanical Parameters","url":"https://www.holosun.eu/en/p/70127430","retrieved":"2026-10-06","via":"harvest"},"note":"1.77 in: 0.03 in less than the drawing's. The page doesn't say what its 45 mm spans."}],"adopt":{"from":"drawing","reason":"The drawing shows what its 1.80 in spans (the lever's end to the housing's other side); the shop's 45 mm is a table entry with no view, and 0.03 in less."},"note":"The drawing's extension lines stand at the QD lever's outer end and at the housing's far side: the housing alone is narrower (body_width)."},"height":{"label":"Overall height (the clamp's bottom to the hood's top)","kind":"length","measurements":[{"id":"drawing","value":2.31,"unit":"in","stated":"2.31 in","source":{"type":"spec","publisher":"manufacturer","name":"Holosun Europe, HS510C (article 70127430): the dimensioned drawing in the page's gallery (side view from the right, end view from the front)","url":"https://www.holosun.eu/media/57/4c/a2/1713444013/2225a2021b0d4cf7ba373fc52f3fb238.jpg","retrieved":"2026-10-06","via":"harvest"}},{"id":"eu","value":59,"unit":"mm","pm":0.5,"stated":"Size: 84x45x59 mm","source":{"type":"spec","publisher":"manufacturer","name":"Holosun Europe, HS510C open reflex red dot sight (article 70127430), Mechanical Parameters","url":"https://www.holosun.eu/en/p/70127430","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"drawing","reason":"The drawing says between which lines; the shop's 59 mm (2.32 in) agrees."},"note":"On its mount: the drawing's extension lines stand at the hood's top and at the mount's lowest edge, below the rail's top."},"body_width":{"label":"Housing width (the sight without its mount)","kind":"length","measurements":[{"id":"us","value":1.68,"unit":"in","stated":"Dimension (in) Body 3.3\" x 1.68\" x 1.78\"","source":{"type":"spec","publisher":"manufacturer","name":"Holosun, HS510C Open Reflex MRS Solar QD Mount, Specs (PHYSICAL DATA)","url":"https://www.holosun.com/products/hs510c","retrieved":"2026-10-06","via":"harvest"}}],"note":"The second of the US page's three \"Body\" figures, taken as the housing's width (Sportsman's Warehouse labels the three L, W, H). The drawing's end view has the housing this wide and the whole 1.80 in over the lever."},"body_height":{"label":"Housing height (the sight without its mount)","kind":"length","measurements":[{"id":"us","value":1.78,"unit":"in","stated":"Dimension (in) Body 3.3\" x 1.68\" x 1.78\"","source":{"type":"spec","publisher":"manufacturer","name":"Holosun, HS510C Open Reflex MRS Solar QD Mount, Specs (PHYSICAL DATA)","url":"https://www.holosun.com/products/hs510c","retrieved":"2026-10-06","via":"harvest"}}],"note":"The third of the US page's three \"Body\" figures, taken as the sight's height off its mount. Not used by the model: the drawing has the hood's top 2.31 in above the clamp's bottom, and the mount alone is 15 mm (0.59 in), which leaves 1.72 in above the mount's top. The 0.06 in between the two isn't explained by any source (the sight may seat into the mount, or the figure may be the width over the lever, which the drawing gives as 1.80)."},"optical_axis_above_rail":{"label":"Optical axis above the rail's top","kind":"length","measurements":[{"id":"drawing","value":1.41,"unit":"in","stated":"1.41 in","source":{"type":"spec","publisher":"manufacturer","name":"Holosun Europe, HS510C (article 70127430): the dimensioned drawing in the page's gallery (side view from the right, end view from the front)","url":"https://www.holosun.eu/media/57/4c/a2/1713444013/2225a2021b0d4cf7ba373fc52f3fb238.jpg","retrieved":"2026-10-06","via":"harvest"}},{"id":"us","value":1.41,"unit":"in","stated":"Integrated QD mount with 1.41 inch dot height for fast installation and iron sight alignment.","source":{"type":"spec","publisher":"manufacturer","name":"Holosun, HS510C Open Reflex MRS Solar QD Mount, Specs (PHYSICAL DATA)","url":"https://www.holosun.com/products/hs510c","retrieved":"2026-10-06","via":"harvest"}},{"id":"eu","value":35.8,"unit":"mm","stated":"line of sight height: 35.8 mm","source":{"type":"spec","publisher":"manufacturer","name":"Holosun Europe, HS510C open reflex red dot sight (article 70127430), Mechanical Parameters","url":"https://www.holosun.eu/en/p/70127430","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"drawing","reason":"The drawing shows what the figure is measured from; the US page's dot height and the shop's 35.8 mm (1.409 in) are the same figure."},"note":"The window's centre above the rail's top. The drawing's 1.41 in runs from the window's centre line to the surface under the mount's cross bar that sits on the rail; Holosun's pages call it the dot height and the line of sight height."},"window_center_above_base":{"label":"Window's centre above the housing's base (the mount's top edge)","kind":"length","measurements":[{"id":"drawing","value":1.04,"unit":"in","stated":"1.04 in","source":{"type":"spec","publisher":"manufacturer","name":"Holosun Europe, HS510C (article 70127430): the dimensioned drawing in the page's gallery (side view from the right, end view from the front)","url":"https://www.holosun.eu/media/57/4c/a2/1713444013/2225a2021b0d4cf7ba373fc52f3fb238.jpg","retrieved":"2026-10-06","via":"harvest"}}],"note":"The drawing's second height on the end view: from the window's centre line down to the line where the housing's front panel ends over the mount."},"window_height":{"label":"Window height","kind":"length","measurements":[{"id":"us","value":0.91,"unit":"in","stated":"Window Size (in) 0.91\" x 1.26\"","source":{"type":"spec","publisher":"manufacturer","name":"Holosun, HS510C Open Reflex MRS Solar QD Mount, Specs (PHYSICAL DATA)","url":"https://www.holosun.com/products/hs510c","retrieved":"2026-10-06","via":"harvest"}},{"id":"eu","value":23,"unit":"mm","pm":0.5,"stated":"Lens size: 23x30 mm","source":{"type":"spec","publisher":"manufacturer","name":"Holosun Europe, HS510C open reflex red dot sight (article 70127430), Mechanical Parameters","url":"https://www.holosun.eu/en/p/70127430","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"us","reason":"The maker's US table; the shop's 23 mm (0.906 in) agrees."}},"window_width":{"label":"Window width","kind":"length","measurements":[{"id":"us","value":1.26,"unit":"in","stated":"Window Size (in) 0.91\" x 1.26\"","source":{"type":"spec","publisher":"manufacturer","name":"Holosun, HS510C Open Reflex MRS Solar QD Mount, Specs (PHYSICAL DATA)","url":"https://www.holosun.com/products/hs510c","retrieved":"2026-10-06","via":"harvest"}},{"id":"eu","value":30,"unit":"mm","pm":0.5,"stated":"Lens size: 23x30 mm","source":{"type":"spec","publisher":"manufacturer","name":"Holosun Europe, HS510C open reflex red dot sight (article 70127430), Mechanical Parameters","url":"https://www.holosun.eu/en/p/70127430","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":32,"unit":"mm","pm":0.5,"stated":"Large 32mm x 24mm lens and open design","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Holosun 510C Solar Powered Red Dot Sight - Multi-Reticle (HS510C), Features","url":"https://www.primaryarms.com/holosun-hs510c-hud-solar-powered-red-dot-sight-with-circle-dot-reticle","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"us","reason":"The maker's US table, which a seller's 32 mm repeats; the European shop's 30 mm stays a visible conflict (it is what the drawing's inner window line reads from the front)."},"note":"Two figures from the maker that differ by 2 mm. The drawing's end view from the front has two nested window lines: the frame's opening (the heavier line, traced as the `window` feature) is 1.256 in wide and 0.99 in high at its arched top's crown, 0.77 at its sides; the lighter line inside it reads about 1.18 by 0.89 in, the shop's 30 x 23 mm. The US page's 1.26 in is the frame opening's width. The model's opening is the traced frame line."},"weight":{"label":"Weight (with its mount)","kind":"mass","measurements":[{"id":"eu","value":215,"unit":"g","pm":0.5,"stated":"Weight: 215 g","source":{"type":"spec","publisher":"manufacturer","name":"Holosun Europe, HS510C open reflex red dot sight (article 70127430), Mechanical Parameters","url":"https://www.holosun.eu/en/p/70127430","retrieved":"2026-10-06","via":"harvest"}},{"id":"reader","value":7.6,"unit":"oz","pm":0.05,"stated":"If you’d weighed the HS510C, you would have found out it weighs 7.6 oz, which is 2.66 oz more than its advertised weight of 4.94 oz.","source":{"type":"spec","publisher":"review","name":"The Truth About Guns, Gear Review: Holosun HS510C Reflex Sight: a reader's comment under the review (not the reviewer's), no scale or method named","url":"https://www.thetruthaboutguns.com/gear-review-holosun-hs510c-reflex-sight/","retrieved":"2026-10-06","via":"harvest"}},{"id":"scheels","value":8.3,"unit":"oz","pm":0.05,"stated":"Weight: 8.3 oz.","source":{"type":"spec","publisher":"retailer","name":"Scheels, Holosun HS510C Red Dot Sight (605930-HS510C), Specifications","url":"https://www.scheels.com/p/holosun-hs510c-red-dot-sight/605930-HS510C","retrieved":"2026-10-06","via":"harvest"},"note":"A seller's figure with nothing said of what is weighed (20 g more than the maker's European figure): kept visible, not used."},{"id":"optics-force","value":9.7,"unit":"oz","pm":0.05,"stated":"Weight 9.7 oz.","source":{"type":"spec","publisher":"retailer","name":"Optics Force, Holosun HS510C 2 MOA Dot, Specs","url":"https://opticsforce.com/products/holosun-hs510c-2-moa-dot","retrieved":"2026-10-06","via":"harvest"},"note":"A second seller's figure, heavier still (275 g), beside the maker's own size for the body alone: most likely a boxed weight. Kept visible, not used."}],"adopt":{"from":"eu","reason":"The maker's own figure for the sight on its mount (it stands beside the size with the mount in it), and a reader's 7.6 oz (215 g) agrees; the two sellers' 8.3 and 9.7 oz say nothing of what they weigh."},"note":"On its QD mount, as it goes on the rifle. Holosun's US page gives the body alone (body_weight); its European shop gives 215 g beside the size that has the mount in it (59 mm high). The body and the mount as published add to 185 g: the 30 g between isn't accounted for by any source (a CR2032 cell is about 3 g)."},"body_weight":{"label":"Weight of the sight without its mount","kind":"mass","measurements":[{"id":"us","value":4.94,"unit":"oz","stated":"Body (oz) Weight 4.94 oz","source":{"type":"spec","publisher":"manufacturer","name":"Holosun, HS510C Open Reflex MRS Solar QD Mount, Specs (PHYSICAL DATA)","url":"https://www.holosun.com/products/hs510c","retrieved":"2026-10-06","via":"harvest"}}]},"mount_weight":{"label":"Weight of the QD mount alone","kind":"mass","measurements":[{"id":"eu-mount","value":45,"unit":"g","pm":0.5,"stated":"Weight: 45 g","source":{"type":"spec","publisher":"manufacturer","name":"Holosun Europe, QD Mount 510C (HS-QD-MOUNT-510C, article 70143980), Mechanical Parameters","url":"https://www.holosun.eu/en/p/70143980","retrieved":"2026-10-06","via":"harvest"}}]},"mount_overall_length":{"label":"QD mount's own length","kind":"length","measurements":[{"id":"eu-mount","value":81,"unit":"mm","pm":0.5,"stated":"Size: 81x42x15 mm","source":{"type":"spec","publisher":"manufacturer","name":"Holosun Europe, QD Mount 510C (HS-QD-MOUNT-510C, article 70143980), Mechanical Parameters","url":"https://www.holosun.eu/en/p/70143980","retrieved":"2026-10-06","via":"harvest"}}],"note":"The mount sold alone (HS-QD-MOUNT-510C): the plate under the housing, longer than the foot that clamps the rail (mount_length)."},"mount_width":{"label":"QD mount's own width","kind":"length","measurements":[{"id":"eu-mount","value":42,"unit":"mm","pm":0.5,"stated":"Size: 81x42x15 mm","source":{"type":"spec","publisher":"manufacturer","name":"Holosun Europe, QD Mount 510C (HS-QD-MOUNT-510C, article 70143980), Mechanical Parameters","url":"https://www.holosun.eu/en/p/70143980","retrieved":"2026-10-06","via":"harvest"}}]},"mount_height":{"label":"QD mount's own height","kind":"length","measurements":[{"id":"eu-mount","value":15,"unit":"mm","pm":0.5,"stated":"Size: 81x42x15 mm","source":{"type":"spec","publisher":"manufacturer","name":"Holosun Europe, QD Mount 510C (HS-QD-MOUNT-510C, article 70143980), Mechanical Parameters","url":"https://www.holosun.eu/en/p/70143980","retrieved":"2026-10-06","via":"harvest"}}]},"mount_length":{"label":"Mount's clamp length along the rail","kind":"length","measurements":[{"id":"drawing-side","value":2.131,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/holosun-hs510c edefb31cce90 (Holosun EU dimensioned drawing, side view from the right (the hood, at the muzzle's end, to the right; the QD lever toward the rear))","scaleRef":"scale from holosun-hs510c.length = 3.3 in (x-extent 707 px → 214.2 px/in) and holosun-hs510c.height = 2.31 in (y-extent 497 px → 215.2 px/in), which agree within 0.4%; mean 214.7 px/in","method":"median row width in y [0.005, 0.03] (0.142–2.170) of the traced outline (tools/trace.py); the side view's lowest rows: the foot's bottom edge, rear corner to front corner","via":"harvest"}},{"id":"photo-left","value":2.189,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/holosun-hs510c 53e72360435d (Primary Arms (HS510C_02), the black HS510C's left side, straight on (the hood to the left))","scaleRef":"the drawing's length (3.30 in) and height (2.31 in) on the photo's own outline, which fit it within 2%","method":"median row width over the foot's lowest rows, 0.005 to 0.03 in above its bottom (2.125 to 2.225 over those rows): the same edge from the other side, with no lever in front of its rear corner","via":"harvest"}}],"adopt":{"from":"drawing-side","reason":"Holosun's drawing, whose two published sizes fit its outline within 0.4%; the seller's photo reads the same edge 0.06 in longer on an outline its two sizes fit to 2%, and stays a visible second reading."},"note":"The foot that sits over the rail, at its bottom edge. Not published: read off the drawing's side view."},"clamp_below_rail":{"label":"Mount clamp's bottom below the rail's top","kind":"length","measurements":[{"id":"drawing-end","value":0.219,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/holosun-hs510c edefb31cce90 (Holosun EU dimensioned drawing, end view from the front (the HOLOSUN panel under the window; the QD lever at the picture's left))","scaleRef":"scale from holosun-hs510c.width = 1.8 in (x-extent 388 px → 215.6 px/in) and holosun-hs510c.height = 2.31 in (y-extent 495 px → 214.3 px/in), which agree within 0.6%; mean 214.9 px/in","method":"y_min in x [-0.25, 0.25] of the traced outline (tools/trace.py); the end view's outline over the rail's middle: the cross bar's underside (where the drawing's 1.41 in line ends) above the mount's lowest edge","via":"harvest"}}],"note":"Not published: read off the drawing's end view, where the 1.41 in line ends on the surface that sits on the rail."},"clamp_bottom_y":{"label":"Mount clamp's bottom in the optic frame (y, the rail's top is 0)","kind":"length","measurements":[{"id":"derived","value":-0.219,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"-{.clamp_below_rail}","via":"harvest"},"note":"Where the traced outlines' clamp-bottom origin sits in the part's frame."}]},"jaw_left_of_middle":{"label":"Left jaw's groove, left of the hood's middle","kind":"length","measurements":[{"id":"drawing-end","value":0.442,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/holosun-hs510c edefb31cce90 (Holosun EU dimensioned drawing, end view from the front (the HOLOSUN panel under the window; the QD lever at the picture's left))","scaleRef":"scale from holosun-hs510c.width = 1.8 in (x-extent 388 px → 215.6 px/in) and holosun-hs510c.height = 2.31 in (y-extent 495 px → 214.3 px/in), which agree within 0.6%; mean 214.9 px/in","method":"−x_min in x [-0.6, 0] in y [0.1, 0.14] of the traced outline (tools/trace.py); the end view's outline inside the left jaw (the fixed one, the clamp bolt's side): its groove at its deepest, left of the hood's middle","via":"harvest"}}],"note":"Not published: read off the drawing's end view. The fixed jaw, on the clamp bolt's side."},"jaw_right_of_middle":{"label":"Right jaw's groove, right of the hood's middle","kind":"length","measurements":[{"id":"drawing-end","value":0.391,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/holosun-hs510c edefb31cce90 (Holosun EU dimensioned drawing, end view from the front (the HOLOSUN panel under the window; the QD lever at the picture's left))","scaleRef":"scale from holosun-hs510c.width = 1.8 in (x-extent 388 px → 215.6 px/in) and holosun-hs510c.height = 2.31 in (y-extent 495 px → 214.3 px/in), which agree within 0.6%; mean 214.9 px/in","method":"x_max in x [0, 0.45] in y [0.1, 0.14] of the traced outline (tools/trace.py); the end view's outline inside the right jaw (the lever's): its groove at its deepest, right of the hood's middle","via":"harvest"}}],"note":"Not published: read off the drawing's end view. The lever's jaw, as the drawing has it: closed."},"jaw_opening":{"label":"Between the two jaws' grooves (what the clamp holds)","kind":"length","measurements":[{"id":"derived","value":0.833,"unit":"in","pm":0.014,"source":{"type":"derived","expr":"{.jaw_left_of_middle} + {.jaw_right_of_middle}","via":"harvest"}}],"note":"As the drawing has the clamp: 0.833 in, for a rail that is 0.835 in across (std.picatinny.top_width). It is the drawing's own check of its scale, and why the two grooves are taken as where the rail is held."},"rail_middle_z":{"label":"The rail's middle in the optic frame (z, the hood's middle is 0)","kind":"length","measurements":[{"id":"derived","value":-0.0255,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"({.jaw_right_of_middle} - {.jaw_left_of_middle}) / 2","via":"harvest"}}],"note":"Midway between the two jaws' grooves: 0.025 in to the left of the hood's middle, by the drawing's end view (5 px of 388). The sight is seated by its jaws, so it stands that far to the right of the rail's middle. If the drawing has the lever's jaw closed further than a rail would let it, the offset is less than this, down to none."}}},{"subject":"huxwrx-flash-hider-qd-556","title":"HUXWRX Flash Hider-QD 556 1/2x28 (1677)","dimensions":{"length":{"label":"Length ahead of the barrel's shoulder, installed (to the front face)","kind":"length","measurements":[{"id":"maker","value":2.3,"unit":"in","stated":"Muzzle device length is 2.3 inches, length added to the barrel is 1.7 inches (on barrels with 0.6\" threads)","source":{"type":"spec","publisher":"manufacturer","name":"HUXWRX Safety Co., FLASH HIDER-QD 556 1/2X28 (SKU 1677), product description","url":"https://huxwrx.com/flash-hider-qd-556-1-2x28/","retrieved":"2026-10-06","via":"harvest"}},{"id":"alexanders","value":2.3,"unit":"in","pm":0.005,"stated":"Muzzle Device Length: 2.30\"","source":{"type":"spec","publisher":"retailer","name":"Alexander's Store, HUXWRX Flash Hider-QD 5.56 1/2x28 Suppressor Mount, Black (Manufacturer Part Number 1677), Specifications","url":"https://alexandersstore.com/product/hux-flash-hider-qd-556-1-2x28/","retrieved":"2026-10-06","via":"harvest"}},{"id":"ar15discounts","value":2.3,"unit":"in","pm":0.005,"stated":"Length: 2.30″","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, HUXWRX 556 QD Flash Hider - 1/2x28 - 1677 (SKU 22296), Specifications","url":"https://ar15discounts.com/products/huxwrx-556-qd-flash-hider-1-2x28/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"maker","reason":"The maker's own figure; two sellers print it with a second decimal place and no other source behind it."},"note":"No washer or shim: no page lists one as included, and HUXWRX's manual has the device threaded \"directly onto the barrel\". Mile High's page for this number (1677) prints the XL 13.7 sibling's sentence (\"Muzzle device length is 2.96 inches, length added to barrel is 2.34 inches\", \"Pre-drilled for ease of pin and weld\"): not this part's, and not recorded as a reading."},"od":{"label":"Largest outside diameter (across the corners of the hex at its rear)","kind":"length","measurements":[{"id":"alexanders","value":1.2,"unit":"in","pm":0.005,"stated":"Diameter: 1.20\"","source":{"type":"spec","publisher":"retailer","name":"Alexander's Store, HUXWRX Flash Hider-QD 5.56 1/2x28 Suppressor Mount, Black (Manufacturer Part Number 1677), Specifications","url":"https://alexandersstore.com/product/hux-flash-hider-qd-556-1-2x28/","retrieved":"2026-10-06","via":"harvest"}},{"id":"photo","value":1.208,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/huxwrx-flash-hider-qd-556 39436d699911 (AR15Discounts' photo of the part standing on its hex, muzzle up, 1920 x 1280)","scaleRef":"its published length (length, 2.3 in) between the middle of its base (row 1176) and the middle of its muzzle face (row 97): 469 px/in along the axis, 481 px/in across it. A close photo from above: the muzzle face's rim is an ellipse 31 px deep on 215 (the lens looks down 8 degrees there), and at the base the corner nearest the lens stands 50 rows under the corner 60 degrees round from it (16 degrees there); the base's middle is the nearest corner's foot (row 1258) less that corner's 0.6 in toward the lens seen at 16 degrees, and lengths along the axis are divided by the cosine of 12 degrees, the mean of the two","method":".cache/hux/profile.py: the silhouette's two edges row by row (luminance below 200), radii from the axis at column 952.3; a feature's station is read where it meets the silhouette's edge, which is at the axis's own depth","via":"harvest"},"note":"The hex's right-hand corner is 266.7 px from the axis and stands 67 degrees round from the lens (the corner nearest the lens is 7 degrees right of the axis): 290 px to a corner, 580 px across two."}],"adopt":{"from":"alexanders","reason":"A published figure, and the photo agrees with it within its own ±: the hex's corners."},"note":"The maker states none. Alexander's \"Diameter\" doesn't say where; on the photo the part's widest place is its hexagonal rear plate, and across its corners the plate reads 1.208 at the scale the published length gives: the two published figures agree on one photo within 0.7%. AR15Discounts' \"Width: 1.6 Length: 3.1 Height: 1.5 Weight: 0.2\" are its package (Alexander's lists \"Package Height 1.5 Package Width 1.5\"), and Sons of Liberty's \"Dimensions 3 × 1 × 1 in\" a shipping box: neither is a reading."},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"alexanders","value":3.3,"unit":"oz","stated":"Weight: 3.3 oz","source":{"type":"spec","publisher":"retailer","name":"Alexander's Store, HUXWRX Flash Hider-QD 5.56 1/2x28 Suppressor Mount, Black (Manufacturer Part Number 1677), Specifications","url":"https://alexandersstore.com/product/hux-flash-hider-qd-556-1-2x28/","retrieved":"2026-10-06","via":"harvest"}},{"id":"ar15discounts","value":3.3,"unit":"oz","pm":0.005,"stated":"Weight: 3.30 oz","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, HUXWRX 556 QD Flash Hider - 1/2x28 - 1677 (SKU 22296), Specifications","url":"https://ar15discounts.com/products/huxwrx-556-qd-flash-hider-1-2x28/","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":3.3,"unit":"oz","stated":"Weight 3.3 oz.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, HUXWRX Flow 556K - Suppressor Only - Black (HX-2448), Specifications table: a row that is the flash hider's, beside \"Length 2.3 in.\"","url":"https://www.primaryarms.com/huxwrx-flow-556k-suppressor-only-black","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"alexanders","reason":"Three sellers agree; the one whose table is for this part and states its other figures too."},"note":"The maker states none. Three sellers print 3.3 oz, and may have it from one another; Primary Arms prints it in its table for the FLOW 556K suppressor alone (\"Length 2.3 in. ... Weight 3.3 oz.\"), where it and the 2.3 in beside it are this part's and not the suppressor's. Sons of Liberty's \"Weight 1 lbs\" and Alexander's \"Shipping Weight 0.25\" are shipping weights. The model's steel comes to within a tenth of it (the part's test)."},"thread_length":{"label":"Barrel thread length it is made for","kind":"length","measurements":[{"id":"maker","value":0.6,"unit":"in","stated":"length added to the barrel is 1.7 inches (on barrels with 0.6\" threads)","source":{"type":"spec","publisher":"manufacturer","name":"HUXWRX Safety Co., FLASH HIDER-QD 556 1/2X28 (SKU 1677), product description","url":"https://huxwrx.com/flash-hider-qd-556-1-2x28/","retrieved":"2026-10-06","via":"harvest"}}],"note":"The maker's words give the thread its two lengths are stated for, not the depth of its threaded hole: `thread_length_made_for`. The Army's barrel has .625 (8448549)."},"thread_major_d":{"label":"Its barrel thread, nominal major diameter","kind":"length","measurements":[{"id":"maker","value":0.5,"unit":"in","pm":0.001,"stated":"FLASH HIDER-QD 556 1/2X28","source":{"type":"spec","publisher":"manufacturer","name":"HUXWRX Safety Co., FLASH HIDER-QD 556 1/2X28 (SKU 1677), product description","url":"https://huxwrx.com/flash-hider-qd-556-1-2x28/","retrieved":"2026-10-06","via":"harvest"}}],"note":"What \"1/2x28\" names: the model's hole for the barrel's thread is a plain hole of this size (the Army's barrel thread is .4957 at most across its crests, 8448549)."},"added_length":{"label":"What it adds to the barrel, by its maker","kind":"length","measurements":[{"id":"maker","value":1.7,"unit":"in","stated":"length added to the barrel is 1.7 inches (on barrels with 0.6\" threads)","source":{"type":"spec","publisher":"manufacturer","name":"HUXWRX Safety Co., FLASH HIDER-QD 556 1/2X28 (SKU 1677), product description","url":"https://huxwrx.com/flash-hider-qd-556-1-2x28/","retrieved":"2026-10-06","via":"harvest"}}],"note":"The maker's own check on length and thread_length: 2.3 less 0.6. Measured from the barrel's muzzle face (\"added to the barrel ... on barrels with 0.6\" threads\")."},"hex_thickness":{"label":"Rear plate (the wrench hex), thickness","kind":"length","measurements":[{"id":"photo","value":0.145,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/huxwrx-flash-hider-qd-556 39436d699911 (AR15Discounts' photo of the part standing on its hex, muzzle up, 1920 x 1280)","scaleRef":"its published length (length, 2.3 in) between the middle of its base (row 1176) and the middle of its muzzle face (row 97): 469 px/in along the axis, 481 px/in across it. A close photo from above: the muzzle face's rim is an ellipse 31 px deep on 215 (the lens looks down 8 degrees there), and at the base the corner nearest the lens stands 50 rows under the corner 60 degrees round from it (16 degrees there); the base's middle is the nearest corner's foot (row 1258) less that corner's 0.6 in toward the lens seen at 16 degrees, and lengths along the axis are divided by the cosine of 12 degrees, the mean of the two","method":".cache/hux/profile.py: the silhouette's two edges row by row (luminance below 200), radii from the axis at column 952.3; a feature's station is read where it meets the silhouette's edge, which is at the axis's own depth","via":"harvest"},"note":"The right-hand corner's edge, rows 1140 to 1206 (the corner's foot; its top is the plate's front face there): 68 px along the axis."},{"id":"manual","value":0.133,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/huxwrx-flow-556k/docs/cc8b363837.pdf (HUXWRX, FLOW Instruction Manual, https://huxwrx.com/content/manuals/FLOWManual.pdf), page 1, \"SUPPRESSOR INSTALL\", the picture over \"The suppressor should be firmly seated\": the maker's rendering of a FLOW suppressor locked onto the muzzle device on a barrel, from the side (947 x 307 px in the file)","scaleRef":"the suppressor's body in the same picture, 247 px across, as the FLOW 556K's published 1.6 in: 154 px/in (the suppressor then reads 5.47 in end to end, against its published 5.5)","method":"the hex plate with its cross hole shows between the barrel and the suppressor's rear face: 20.5 px along the axis, 175 px across (1.13 in)","via":"harvest"}}],"adopt":{"from":"photo","reason":"A photograph of the part, at the part's own published scale; the maker's rendering, scaled by another part, agrees within 0.012 in."},"note":"The plate the QD wrench takes (HUXWRX's manual: \"index the hex flats on the muzzle device\"). Its front face is where a FLOW suppressor's rear face stops: suppressor_seat_x."},"hex_across_flats":{"label":"Rear plate, across the flats","kind":"length","measurements":[{"id":"photo","value":1.04,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/huxwrx-flash-hider-qd-556 39436d699911 (AR15Discounts' photo of the part standing on its hex, muzzle up, 1920 x 1280)","scaleRef":"its published length (length, 2.3 in) between the middle of its base (row 1176) and the middle of its muzzle face (row 97): 469 px/in along the axis, 481 px/in across it. A close photo from above: the muzzle face's rim is an ellipse 31 px deep on 215 (the lens looks down 8 degrees there), and at the base the corner nearest the lens stands 50 rows under the corner 60 degrees round from it (16 degrees there); the base's middle is the nearest corner's foot (row 1258) less that corner's 0.6 in toward the lens seen at 16 degrees, and lengths along the axis are divided by the cosine of 12 degrees, the mean of the two","method":".cache/hux/profile.py: the silhouette's two edges row by row (luminance below 200), radii from the axis at column 952.3; a feature's station is read where it meets the silhouette's edge, which is at the axis's own depth","via":"harvest"},"note":"The corner's 290 px from the axis times the cosine of 30 degrees: 251 px to a flat."}],"note":"A hexagon cut on a round: the corners keep a narrow land of the round's turned surface (Rooftop Defense's photo of the rear face, 477c03bb60a8). No page states the wrench's size."},"neck_d":{"label":"Relief between the hex and the suppressor's thread, diameter","kind":"length","measurements":[{"id":"photo","value":1.015,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/huxwrx-flash-hider-qd-556 39436d699911 (AR15Discounts' photo of the part standing on its hex, muzzle up, 1920 x 1280)","scaleRef":"its published length (length, 2.3 in) between the middle of its base (row 1176) and the middle of its muzzle face (row 97): 469 px/in along the axis, 481 px/in across it. A close photo from above: the muzzle face's rim is an ellipse 31 px deep on 215 (the lens looks down 8 degrees there), and at the base the corner nearest the lens stands 50 rows under the corner 60 degrees round from it (16 degrees there); the base's middle is the nearest corner's foot (row 1258) less that corner's 0.6 in toward the lens seen at 16 degrees, and lengths along the axis are divided by the cosine of 12 degrees, the mean of the two","method":".cache/hux/profile.py: the silhouette's two edges row by row (luminance below 200), radii from the axis at column 952.3; a feature's station is read where it meets the silhouette's edge, which is at the axis's own depth","via":"harvest"},"note":"Rows 1086 to 1108: 242.7 to 246 px from the axis on either side."}]},"neck_length":{"label":"Relief between the hex and the suppressor's thread, length","kind":"length","measurements":[{"id":"photo","value":0.047,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/huxwrx-flash-hider-qd-556 39436d699911 (AR15Discounts' photo of the part standing on its hex, muzzle up, 1920 x 1280)","scaleRef":"its published length (length, 2.3 in) between the middle of its base (row 1176) and the middle of its muzzle face (row 97): 469 px/in along the axis, 481 px/in across it. A close photo from above: the muzzle face's rim is an ellipse 31 px deep on 215 (the lens looks down 8 degrees there), and at the base the corner nearest the lens stands 50 rows under the corner 60 degrees round from it (16 degrees there); the base's middle is the nearest corner's foot (row 1258) less that corner's 0.6 in toward the lens seen at 16 degrees, and lengths along the axis are divided by the cosine of 12 degrees, the mean of the two","method":".cache/hux/profile.py: the silhouette's two edges row by row (luminance below 200), radii from the axis at column 952.3; a feature's station is read where it meets the silhouette's edge, which is at the axis's own depth","via":"harvest"},"note":"Rows 1086 to 1108."}]},"qd_thread_od":{"label":"The suppressor's thread on it, diameter across the crests","kind":"length","measurements":[{"id":"photo","value":1.123,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/huxwrx-flash-hider-qd-556 39436d699911 (AR15Discounts' photo of the part standing on its hex, muzzle up, 1920 x 1280)","scaleRef":"its published length (length, 2.3 in) between the middle of its base (row 1176) and the middle of its muzzle face (row 97): 469 px/in along the axis, 481 px/in across it. A close photo from above: the muzzle face's rim is an ellipse 31 px deep on 215 (the lens looks down 8 degrees there), and at the base the corner nearest the lens stands 50 rows under the corner 60 degrees round from it (16 degrees there); the base's middle is the nearest corner's foot (row 1258) less that corner's 0.6 in toward the lens seen at 16 degrees, and lengths along the axis are divided by the cosine of 12 degrees, the mean of the two","method":".cache/hux/profile.py: the silhouette's two edges row by row (luminance below 200), radii from the axis at column 952.3; a feature's station is read where it meets the silhouette's edge, which is at the axis's own depth","via":"harvest"},"note":"The silhouette's edges at their widest on each side, 271.3 px left and 268.7 px right of the axis, half a turn apart along it."}],"note":"HUXWRX's \"Torque Lock\" mount: a coarse thread of about three turns that the suppressor goes onto counter-clockwise (the manual: \"Thread the suppressor counter-clockwise onto the QD muzzle device until hand-tight\"; Silencer Shop: \"left-hand threads\"). Its size is published nowhere found. How deep it is cut isn't read: the photo's grooves are 8 to 10 px wide and soft, and the silhouette follows them only 5 px in."},"qd_thread_pitch":{"label":"The suppressor's thread on it, pitch","kind":"length","measurements":[{"id":"photo","value":0.083,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/huxwrx-flash-hider-qd-556 39436d699911 (AR15Discounts' photo of the part standing on its hex, muzzle up, 1920 x 1280)","scaleRef":"its published length (length, 2.3 in) between the middle of its base (row 1176) and the middle of its muzzle face (row 97): 469 px/in along the axis, 481 px/in across it. A close photo from above: the muzzle face's rim is an ellipse 31 px deep on 215 (the lens looks down 8 degrees there), and at the base the corner nearest the lens stands 50 rows under the corner 60 degrees round from it (16 degrees there); the base's middle is the nearest corner's foot (row 1258) less that corner's 0.6 in toward the lens seen at 16 degrees, and lengths along the axis are divided by the cosine of 12 degrees, the mean of the two","method":".cache/hux/profile.py: the silhouette's two edges row by row (luminance below 200), radii from the axis at column 952.3; a feature's station is read where it meets the silhouette's edge, which is at the axis's own depth","via":"harvest"},"note":"A crest returns to the same side every 40 rows (the left edge is widest at rows 998 and 1038, the right at 980 and 1020, half a pitch between: a helix): 40 px at 481 px/in. Twelve to the inch is 0.0833; 2 mm would be 0.0787."}]},"qd_thread_length":{"label":"The suppressor's thread on it, length","kind":"length","measurements":[{"id":"photo","value":0.236,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/huxwrx-flash-hider-qd-556 39436d699911 (AR15Discounts' photo of the part standing on its hex, muzzle up, 1920 x 1280)","scaleRef":"its published length (length, 2.3 in) between the middle of its base (row 1176) and the middle of its muzzle face (row 97): 469 px/in along the axis, 481 px/in across it. A close photo from above: the muzzle face's rim is an ellipse 31 px deep on 215 (the lens looks down 8 degrees there), and at the base the corner nearest the lens stands 50 rows under the corner 60 degrees round from it (16 degrees there); the base's middle is the nearest corner's foot (row 1258) less that corner's 0.6 in toward the lens seen at 16 degrees, and lengths along the axis are divided by the cosine of 12 degrees, the mean of the two","method":".cache/hux/profile.py: the silhouette's two edges row by row (luminance below 200), radii from the axis at column 952.3; a feature's station is read where it meets the silhouette's edge, which is at the axis's own depth","via":"harvest"},"note":"Rows 975 to 1086: from the step at its front to the relief behind it. Under three turns at its pitch."}]},"cone_rear_x":{"label":"The taper's wide end, from the rear face","kind":"length","measurements":[{"id":"photo","value":0.465,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/huxwrx-flash-hider-qd-556 39436d699911 (AR15Discounts' photo of the part standing on its hex, muzzle up, 1920 x 1280)","scaleRef":"its published length (length, 2.3 in) between the middle of its base (row 1176) and the middle of its muzzle face (row 97): 469 px/in along the axis, 481 px/in across it. A close photo from above: the muzzle face's rim is an ellipse 31 px deep on 215 (the lens looks down 8 degrees there), and at the base the corner nearest the lens stands 50 rows under the corner 60 degrees round from it (16 degrees there); the base's middle is the nearest corner's foot (row 1258) less that corner's 0.6 in toward the lens seen at 16 degrees, and lengths along the axis are divided by the cosine of 12 degrees, the mean of the two","method":".cache/hux/profile.py: the silhouette's two edges row by row (luminance below 200), radii from the axis at column 952.3; a feature's station is read where it meets the silhouette's edge, which is at the axis's own depth","via":"harvest"},"note":"Row 958: the silhouette steps in from the thread to 244 px from the axis."}],"note":"The cone between the suppressor's thread and the slotted body: the manual's \"taper mounting surfaces\". A small step separates it from the thread's front end."},"cone_rear_d":{"label":"The taper's wide end, diameter","kind":"length","measurements":[{"id":"photo","value":1.015,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/huxwrx-flash-hider-qd-556 39436d699911 (AR15Discounts' photo of the part standing on its hex, muzzle up, 1920 x 1280)","scaleRef":"its published length (length, 2.3 in) between the middle of its base (row 1176) and the middle of its muzzle face (row 97): 469 px/in along the axis, 481 px/in across it. A close photo from above: the muzzle face's rim is an ellipse 31 px deep on 215 (the lens looks down 8 degrees there), and at the base the corner nearest the lens stands 50 rows under the corner 60 degrees round from it (16 degrees there); the base's middle is the nearest corner's foot (row 1258) less that corner's 0.6 in toward the lens seen at 16 degrees, and lengths along the axis are divided by the cosine of 12 degrees, the mean of the two","method":".cache/hux/profile.py: the silhouette's two edges row by row (luminance below 200), radii from the axis at column 952.3; a feature's station is read where it meets the silhouette's edge, which is at the axis's own depth","via":"harvest"},"note":"488 px across at rows 950 to 958."}]},"body_x":{"label":"Where the taper ends and the slotted body begins, from the rear face","kind":"length","measurements":[{"id":"photo","value":0.669,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/huxwrx-flash-hider-qd-556 39436d699911 (AR15Discounts' photo of the part standing on its hex, muzzle up, 1920 x 1280)","scaleRef":"its published length (length, 2.3 in) between the middle of its base (row 1176) and the middle of its muzzle face (row 97): 469 px/in along the axis, 481 px/in across it. A close photo from above: the muzzle face's rim is an ellipse 31 px deep on 215 (the lens looks down 8 degrees there), and at the base the corner nearest the lens stands 50 rows under the corner 60 degrees round from it (16 degrees there); the base's middle is the nearest corner's foot (row 1258) less that corner's 0.6 in toward the lens seen at 16 degrees, and lengths along the axis are divided by the cosine of 12 degrees, the mean of the two","method":".cache/hux/profile.py: the silhouette's two edges row by row (luminance below 200), radii from the axis at column 952.3; a feature's station is read where it meets the silhouette's edge, which is at the axis's own depth","via":"harvest"},"note":"Row 862: the cone's edge (a straight line from row 958) meets the body's."}]},"body_d":{"label":"Slotted body, outside diameter","kind":"length","measurements":[{"id":"photo","value":0.895,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/huxwrx-flash-hider-qd-556 39436d699911 (AR15Discounts' photo of the part standing on its hex, muzzle up, 1920 x 1280)","scaleRef":"its published length (length, 2.3 in) between the middle of its base (row 1176) and the middle of its muzzle face (row 97): 469 px/in along the axis, 481 px/in across it. A close photo from above: the muzzle face's rim is an ellipse 31 px deep on 215 (the lens looks down 8 degrees there), and at the base the corner nearest the lens stands 50 rows under the corner 60 degrees round from it (16 degrees there); the base's middle is the nearest corner's foot (row 1258) less that corner's 0.6 in toward the lens seen at 16 degrees, and lengths along the axis are divided by the cosine of 12 degrees, the mean of the two","method":".cache/hux/profile.py: the silhouette's two edges row by row (luminance below 200), radii from the axis at column 952.3; a feature's station is read where it meets the silhouette's edge, which is at the axis's own depth","via":"harvest"},"note":"430.5 px across over rows 110 to 340, where no slot is at the silhouette's edge. Further down the edge is a slot's two rims and reads narrower (397 px at row 600)."}]},"slots":{"label":"Helical slots through the body, count","kind":"count","measurements":[{"id":"photo","value":6,"unit":"count","source":{"type":"photo","photo":"references/huxwrx-flash-hider-qd-556 39436d699911 (AR15Discounts' photo of the part standing on its hex, muzzle up, 1920 x 1280)","scaleRef":"its published length (length, 2.3 in) between the middle of its base (row 1176) and the middle of its muzzle face (row 97): 469 px/in along the axis, 481 px/in across it. A close photo from above: the muzzle face's rim is an ellipse 31 px deep on 215 (the lens looks down 8 degrees there), and at the base the corner nearest the lens stands 50 rows under the corner 60 degrees round from it (16 degrees there); the base's middle is the nearest corner's foot (row 1258) less that corner's 0.6 in toward the lens seen at 16 degrees, and lengths along the axis are divided by the cosine of 12 degrees, the mean of the two","method":".cache/hux/profile.py: the silhouette's two edges row by row (luminance below 200), radii from the axis at column 952.3; a feature's station is read where it meets the silhouette's edge, which is at the axis's own depth","via":"harvest"},"note":".cache/hux/rowlum.py: luminance along rows 500 and 600 by angle round the body (the arcsine of the offset from the axis over the body's 215 px): lit bars read 60 to 110, a slot's shadow 23 to 34, and background seen through a slot 190 to 254."}],"note":"Counted on the angles of one photo, since no view from the muzzle end shows the whole turn: at row 600 the near side has a slot from 47 to 3 degrees left of the axis, a bar 15 degrees wide, and a slot from 13 to 57 degrees right; at row 500 the slots' middles are 20 degrees left and 39 right. Sixty degrees from one slot to the next: six round the body. (Three would be 120 degrees apart, and one side view could not hold two whole ones and part of a third, which every side view of the part does.)"},"slot_rear_x":{"label":"Slots, rear ends, from the rear face","kind":"length","measurements":[{"id":"photo","value":0.663,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/huxwrx-flash-hider-qd-556 39436d699911 (AR15Discounts' photo of the part standing on its hex, muzzle up, 1920 x 1280)","scaleRef":"its published length (length, 2.3 in) between the middle of its base (row 1176) and the middle of its muzzle face (row 97): 469 px/in along the axis, 481 px/in across it. A close photo from above: the muzzle face's rim is an ellipse 31 px deep on 215 (the lens looks down 8 degrees there), and at the base the corner nearest the lens stands 50 rows under the corner 60 degrees round from it (16 degrees there); the base's middle is the nearest corner's foot (row 1258) less that corner's 0.6 in toward the lens seen at 16 degrees, and lengths along the axis are divided by the cosine of 12 degrees, the mean of the two","method":".cache/hux/profile.py: the silhouette's two edges row by row (luminance below 200), radii from the axis at column 952.3; a feature's station is read where it meets the silhouette's edge, which is at the axis's own depth","via":"harvest"},"note":"The round ends at about row 865, where the taper meets the body."}]},"slot_front_x":{"label":"Slots, front tips, from the rear face","kind":"length","measurements":[{"id":"photo","value":2.11,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/huxwrx-flash-hider-qd-556 39436d699911 (AR15Discounts' photo of the part standing on its hex, muzzle up, 1920 x 1280)","scaleRef":"its published length (length, 2.3 in) between the middle of its base (row 1176) and the middle of its muzzle face (row 97): 469 px/in along the axis, 481 px/in across it. A close photo from above: the muzzle face's rim is an ellipse 31 px deep on 215 (the lens looks down 8 degrees there), and at the base the corner nearest the lens stands 50 rows under the corner 60 degrees round from it (16 degrees there); the base's middle is the nearest corner's foot (row 1258) less that corner's 0.6 in toward the lens seen at 16 degrees, and lengths along the axis are divided by the cosine of 12 degrees, the mean of the two","method":".cache/hux/profile.py: the silhouette's two edges row by row (luminance below 200), radii from the axis at column 952.3; a feature's station is read where it meets the silhouette's edge, which is at the axis's own depth","via":"harvest"},"note":"The pointed tips at about row 185: 0.19 in of unbroken ring is left to the muzzle face."}]},"slot_width":{"label":"Slots, width round the body at their widest","kind":"angle","measurements":[{"id":"photo","value":45,"unit":"deg","pm":5,"source":{"type":"photo","photo":"references/huxwrx-flash-hider-qd-556 39436d699911 (AR15Discounts' photo of the part standing on its hex, muzzle up, 1920 x 1280)","scaleRef":"its published length (length, 2.3 in) between the middle of its base (row 1176) and the middle of its muzzle face (row 97): 469 px/in along the axis, 481 px/in across it. A close photo from above: the muzzle face's rim is an ellipse 31 px deep on 215 (the lens looks down 8 degrees there), and at the base the corner nearest the lens stands 50 rows under the corner 60 degrees round from it (16 degrees there); the base's middle is the nearest corner's foot (row 1258) less that corner's 0.6 in toward the lens seen at 16 degrees, and lengths along the axis are divided by the cosine of 12 degrees, the mean of the two","method":".cache/hux/profile.py: the silhouette's two edges row by row (luminance below 200), radii from the axis at column 952.3; a feature's station is read where it meets the silhouette's edge, which is at the axis's own depth","via":"harvest"},"note":"Rows 500 to 820: 44 and 45 degrees at rows 500 and 600. 0.34 in across the chord."}]},"slot_taper_x":{"label":"Slots, where each begins to narrow toward its front tip, from the rear face","kind":"length","measurements":[{"id":"photo","value":1.55,"unit":"in","pm":0.1,"source":{"type":"photo","photo":"references/huxwrx-flash-hider-qd-556 39436d699911 (AR15Discounts' photo of the part standing on its hex, muzzle up, 1920 x 1280)","scaleRef":"its published length (length, 2.3 in) between the middle of its base (row 1176) and the middle of its muzzle face (row 97): 469 px/in along the axis, 481 px/in across it. A close photo from above: the muzzle face's rim is an ellipse 31 px deep on 215 (the lens looks down 8 degrees there), and at the base the corner nearest the lens stands 50 rows under the corner 60 degrees round from it (16 degrees there); the base's middle is the nearest corner's foot (row 1258) less that corner's 0.6 in toward the lens seen at 16 degrees, and lengths along the axis are divided by the cosine of 12 degrees, the mean of the two","method":".cache/hux/profile.py: the silhouette's two edges row by row (luminance below 200), radii from the axis at column 952.3; a feature's station is read where it meets the silhouette's edge, which is at the axis's own depth","via":"harvest"},"note":"Full width to about row 450; about 10 degrees wide at row 300 and a point at row 185."}]},"slot_twist":{"label":"Slots, turn about the axis per inch toward the muzzle","kind":"angle","measurements":[{"id":"photo","value":35,"unit":"deg","pm":7,"source":{"type":"photo","photo":"references/huxwrx-flash-hider-qd-556 39436d699911 (AR15Discounts' photo of the part standing on its hex, muzzle up, 1920 x 1280)","scaleRef":"its published length (length, 2.3 in) between the middle of its base (row 1176) and the middle of its muzzle face (row 97): 469 px/in along the axis, 481 px/in across it. A close photo from above: the muzzle face's rim is an ellipse 31 px deep on 215 (the lens looks down 8 degrees there), and at the base the corner nearest the lens stands 50 rows under the corner 60 degrees round from it (16 degrees there); the base's middle is the nearest corner's foot (row 1258) less that corner's 0.6 in toward the lens seen at 16 degrees, and lengths along the axis are divided by the cosine of 12 degrees, the mean of the two","method":".cache/hux/profile.py: the silhouette's two edges row by row (luminance below 200), radii from the axis at column 952.3; a feature's station is read where it meets the silhouette's edge, which is at the axis's own depth","via":"harvest"},"note":"The middle of the bar between two slots: 21 degrees right of the axis at row 300, 9.5 at row 500, 5 at row 600, 10 left at row 800 (29 degrees an inch); the same bar's edge from foot to tip turns 63 degrees in 1.49 in (42 an inch)."}],"note":"Right-hand: seen from outside with the muzzle up, a slot leans to the right as it rises. Two readings of one photo that differ by a third; the model takes the middle of them."},"ring_id":{"label":"Muzzle ring, inside diameter (the cavity the slots open into)","kind":"length","measurements":[{"id":"photo","value":0.77,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/huxwrx-flash-hider-qd-556 1e8bfe213942 (Rooftop Defense's photo of the part standing, muzzle up, seen from about 15 degrees above, 2000 x 2000)","scaleRef":"the muzzle ring's own outside, 650 px across in the photo, as body_d (0.895 in): the same face, the same plane","method":"widths across the muzzle face's ellipses at their widest","via":"harvest"},"note":"The ring's inner edge is 560 px across: 0.86 of its outside."}]},"core_od":{"label":"The core inside the muzzle ring, outside diameter","kind":"length","measurements":[{"id":"photo","value":0.434,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/huxwrx-flash-hider-qd-556 1e8bfe213942 (Rooftop Defense's photo of the part standing, muzzle up, seen from about 15 degrees above, 2000 x 2000)","scaleRef":"the muzzle ring's own outside, 650 px across in the photo, as body_d (0.895 in): the same face, the same plane","method":"widths across the muzzle face's ellipses at their widest","via":"harvest"},"note":"315 px across its lugs."}],"note":"A tube on the axis inside the slotted body, with the bore through it: its end shows inside the muzzle ring as a ring with lugs standing on it."},"bore_d":{"label":"Exit bore, as it shows in the core's end","kind":"length","measurements":[{"id":"photo","value":0.275,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/huxwrx-flash-hider-qd-556 1e8bfe213942 (Rooftop Defense's photo of the part standing, muzzle up, seen from about 15 degrees above, 2000 x 2000)","scaleRef":"the muzzle ring's own outside, 650 px across in the photo, as body_d (0.895 in): the same face, the same plane","method":"widths across the muzzle face's ellipses at their widest","via":"harvest"},"note":"200 px across."}]},"core_recess":{"label":"The core's lugs, how far their tops stand behind the muzzle face","kind":"length","measurements":[{"id":"photo","value":0.03,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/huxwrx-flash-hider-qd-556 1e8bfe213942 (Rooftop Defense's photo of the part standing, muzzle up, seen from about 15 degrees above, 2000 x 2000)","scaleRef":"the muzzle ring's own outside, 650 px across in the photo, as body_d (0.895 in): the same face, the same plane","method":"widths across the muzzle face's ellipses at their widest","via":"harvest"},"note":"The lugs' tops lie within 20 px of the level of the muzzle face's middle at this elevation: flush or just under."}]},"core_notch_depth":{"label":"The core's end, depth of the gaps between its lugs","kind":"length","measurements":[{"id":"photo","value":0.08,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/huxwrx-flash-hider-qd-556 1e8bfe213942 (Rooftop Defense's photo of the part standing, muzzle up, seen from about 15 degrees above, 2000 x 2000)","scaleRef":"the muzzle ring's own outside, 650 px across in the photo, as body_d (0.895 in): the same face, the same plane","method":"widths across the muzzle face's ellipses at their widest","via":"harvest"},"note":"The arc between two lugs lies about 110 px lower in the picture than their tops."}]},"rear_holes":{"label":"Rear face, holes round the thread, count","kind":"count","measurements":[{"id":"photo","value":9,"unit":"count","source":{"type":"photo","photo":"references/huxwrx-flash-hider-qd-556 477c03bb60a8 (Rooftop Defense's photo of the part standing on its muzzle, the rear face up, 2000 x 2000)","scaleRef":"the suppressor's thread just under the plate, 856 px across, as qd_thread_od (1.123 in): 762 px/in. The plate is nearer the lens than the thread by a quarter inch, so its features read a few percent large","method":"the holes' centres on the ellipse the face's circle makes (semi-axes 319 and 94 px), each one's angle round it","via":"harvest"}}],"note":"Nine holes at ten places 36 degrees apart: the tenth place is left solid. Unwrapped about the face's middle on Rooftop Defense's photo of the rear face, the holes stand at 168, 139, 102, 65, 27, -8, -43, -80 and -115 degrees, each 35 to 38 from the next but for one gap of 77."},"rear_hole_circle_d":{"label":"Rear face, the circle its holes are on, diameter","kind":"length","measurements":[{"id":"photo","value":0.82,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/huxwrx-flash-hider-qd-556 477c03bb60a8 (Rooftop Defense's photo of the part standing on its muzzle, the rear face up, 2000 x 2000)","scaleRef":"the suppressor's thread just under the plate, 856 px across, as qd_thread_od (1.123 in): 762 px/in. The plate is nearer the lens than the thread by a quarter inch, so its features read a few percent large","method":"the holes' centres on the ellipse the face's circle makes (semi-axes 319 and 94 px), each one's angle round it","via":"harvest"},"note":"638 px between opposite holes' centres, less 2% for the plate's nearness."}]},"rear_hole_d":{"label":"Rear face, hole diameter","kind":"length","measurements":[{"id":"photo","value":0.16,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/huxwrx-flash-hider-qd-556 477c03bb60a8 (Rooftop Defense's photo of the part standing on its muzzle, the rear face up, 2000 x 2000)","scaleRef":"the suppressor's thread just under the plate, 856 px across, as qd_thread_od (1.123 in): 762 px/in. The plate is nearer the lens than the thread by a quarter inch, so its features read a few percent large","method":"the holes' centres on the ellipse the face's circle makes (semi-axes 319 and 94 px), each one's angle round it","via":"harvest"},"note":"125 px across a hole."}]},"cross_hole_d":{"label":"The hole across one flat of the hex, diameter","kind":"length","measurements":[{"id":"photo","value":0.123,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/huxwrx-flash-hider-qd-556 39436d699911 (AR15Discounts' photo of the part standing on its hex, muzzle up, 1920 x 1280)","scaleRef":"its published length (length, 2.3 in) between the middle of its base (row 1176) and the middle of its muzzle face (row 97): 469 px/in along the axis, 481 px/in across it. A close photo from above: the muzzle face's rim is an ellipse 31 px deep on 215 (the lens looks down 8 degrees there), and at the base the corner nearest the lens stands 50 rows under the corner 60 degrees round from it (16 degrees there); the base's middle is the nearest corner's foot (row 1258) less that corner's 0.6 in toward the lens seen at 16 degrees, and lengths along the axis are divided by the cosine of 12 degrees, the mean of the two","method":".cache/hux/profile.py: the silhouette's two edges row by row (luminance below 200), radii from the axis at column 952.3; a feature's station is read where it meets the silhouette's edge, which is at the axis's own depth","via":"harvest"},"note":"59 px across."}],"note":"One round hole in the middle of one flat, at half the plate's thickness; what it is for isn't said on any page read (the XL 13.7 sibling is \"Pre-drilled for ease of pin and weld\")."},"suppressor_seat_x":{"label":"Where a FLOW suppressor's rear face stands when it is locked on, from the rear face (the barrel's shoulder)","kind":"length","measurements":[{"id":"hex","value":0.145,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{.hex_thickness}","via":"harvest"},"note":"The plate's own thickness, off the part's photo."},{"id":"manual","value":0.133,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/huxwrx-flow-556k/docs/cc8b363837.pdf (HUXWRX, FLOW Instruction Manual, https://huxwrx.com/content/manuals/FLOWManual.pdf), page 1, \"SUPPRESSOR INSTALL\", the picture over \"The suppressor should be firmly seated\": the maker's rendering of a FLOW suppressor locked onto the muzzle device on a barrel, from the side (947 x 307 px in the file)","scaleRef":"the suppressor's body in the same picture, 247 px across, as the FLOW 556K's published 1.6 in: 154 px/in (the suppressor then reads 5.47 in end to end, against its published 5.5)","method":"the hex plate with its cross hole shows between the barrel and the suppressor's rear face: 20.5 px along the axis, 175 px across (1.13 in)","via":"harvest"},"note":"The rendering shows the suppressor's rear face against the hex's front face, no gap between them at 154 px/in."}],"adopt":{"from":"hex","reason":"The part's own photo; the maker's rendering of the pair seated shows the same plane and agrees within 0.012 in."},"note":"The hex plate's front face: the suppressor's collar comes down to it and leaves the hex showing behind it (the maker's own rendering of the pair, seated). It cannot come further: the suppressor's mouth is its thread (1.12 in across, the photos of both suppressors' rear ends), and the hex is 1.20 across its corners. The suppressors' published \"length added to barrel\" would have it 0.03 to 0.07 in BEHIND the shoulder on a 0.6 in thread (5.5 less 4.9, 6.8 less 6.1; in the maker's centimetres 16 and 17 mm): 0.17 to 0.21 in from here, which the figures' rounding doesn't cover. Each suppressor's ledger has that as a conflict on its added_length."}}},{"subject":"huxwrx-flow-556-ti","title":"HUXWRX FLOW 556 Ti (3059 black, 2693 FDE)","dimensions":{"length":{"label":"Overall length, rear face to front face","kind":"length","measurements":[{"id":"paper","value":6.8,"unit":"in","stated":"6.8in / 17.2cm","source":{"type":"spec","publisher":"manufacturer","name":"HUXWRX Safety Co., FLOW 556 Ti white paper (\"LIGHTWEIGHT AND LONG-LASTING\"), one page: the dimensioned drawing and PRODUCT SPECIFICATIONS; references/huxwrx-flow-556-ti/docs/09a65d6ade.pdf","url":"https://huxwrx.com/content/white-paper/FLOW-556-Ti-White-Paper.pdf","retrieved":"2026-10-06","via":"harvest"}},{"id":"page","value":6.8,"unit":"in","stated":"WEIGHT 11.4 oz / 323 g LENGTH 6.8 in / 17.2 cm DIAMETER 1.8 in / 4.6 cm AVAILABLE IN BLACK & FDE","source":{"type":"spec","publisher":"manufacturer","name":"HUXWRX Safety Co., FLOW 556 Ti product page","url":"https://huxwrx.com/flow-556-ti","retrieved":"2026-10-06","via":"harvest"}},{"id":"capitol","value":6.8,"unit":"in","stated":"It weighs 11.4 oz, measures 6.8\" long with a 1.8\" diameter, and adds 6.1\" to the barrel, with no barrel length restrictions.","source":{"type":"spec","publisher":"retailer","name":"Capitol Armory, Huxwrx FLOW 556 Ti (HUX-556TI-3292; sold without a muzzle device)","url":"https://www.capitolarmory.com/huxwrx-flow-556-ti-titanium-556-ar15-rifle-silencer.html","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":6.8,"unit":"in","stated":"Diameter: 1.8\" Overall Length: 6.8\" Weight: 11.4 oz.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, HUXWRX FLOW 556 TI Suppressor - Black (SKU 3059, MPN 3059), Features","url":"https://www.primaryarms.com/huxwrx-flow-5-56-ti-suppressor-black","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"paper","reason":"The maker's drawing, with the figure on its dimension line; its page and two sellers say the same."},"note":"The white paper's dimension line runs under the whole side outline, from the hex collar's rear face to the tip of the cap: the can alone, no muzzle device in it. In centimetres 17.2 (6.77 in)."},"od":{"label":"Largest outside diameter (the body; the grip texture at the base stands on it)","kind":"length","measurements":[{"id":"paper","value":1.8,"unit":"in","stated":"1.8in* 4.6cm*","source":{"type":"spec","publisher":"manufacturer","name":"HUXWRX Safety Co., FLOW 556 Ti white paper (\"LIGHTWEIGHT AND LONG-LASTING\"), one page: the dimensioned drawing and PRODUCT SPECIFICATIONS; references/huxwrx-flow-556-ti/docs/09a65d6ade.pdf","url":"https://huxwrx.com/content/white-paper/FLOW-556-Ti-White-Paper.pdf","retrieved":"2026-10-06","via":"harvest"}},{"id":"page","value":1.8,"unit":"in","stated":"DIAMETER 1.8 in / 4.6 cm","source":{"type":"spec","publisher":"manufacturer","name":"HUXWRX Safety Co., FLOW 556 Ti product page","url":"https://huxwrx.com/flow-556-ti","retrieved":"2026-10-06","via":"harvest"}},{"id":"capitol","value":1.8,"unit":"in","stated":"measures 6.8\" long with a 1.8\" diameter","source":{"type":"spec","publisher":"retailer","name":"Capitol Armory, Huxwrx FLOW 556 Ti (HUX-556TI-3292; sold without a muzzle device)","url":"https://www.capitolarmory.com/huxwrx-flow-556-ti-titanium-556-ar15-rifle-silencer.html","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":1.8,"unit":"in","stated":"Diameter: 1.8\"","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, HUXWRX FLOW 556 TI Suppressor - Black (SKU 3059, MPN 3059), Features","url":"https://www.primaryarms.com/huxwrx-flow-5-56-ti-suppressor-black","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"paper","reason":"The maker's drawing; its page and two sellers say the same."},"note":"The paper's 1.8 in is starred: \"*Base grip texture adds 0.05in (0.127cm)\" (grip_texture). In centimetres 4.6 (1.81 in)."},"grip_texture":{"label":"What the base's grip texture adds to the diameter","kind":"length","measurements":[{"id":"paper","value":0.05,"unit":"in","pm":0.005,"stated":"*Base grip texture adds 0.05in (0.127cm)","source":{"type":"spec","publisher":"manufacturer","name":"HUXWRX Safety Co., FLOW 556 Ti white paper (\"LIGHTWEIGHT AND LONG-LASTING\"), one page: the dimensioned drawing and PRODUCT SPECIFICATIONS; references/huxwrx-flow-556-ti/docs/09a65d6ade.pdf","url":"https://huxwrx.com/content/white-paper/FLOW-556-Ti-White-Paper.pdf","retrieved":"2026-10-06","via":"harvest"}}]},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"paper","value":11.4,"unit":"oz","stated":"11.4oz / 323g","source":{"type":"spec","publisher":"manufacturer","name":"HUXWRX Safety Co., FLOW 556 Ti white paper (\"LIGHTWEIGHT AND LONG-LASTING\"), one page: the dimensioned drawing and PRODUCT SPECIFICATIONS; references/huxwrx-flow-556-ti/docs/09a65d6ade.pdf","url":"https://huxwrx.com/content/white-paper/FLOW-556-Ti-White-Paper.pdf","retrieved":"2026-10-06","via":"harvest"}},{"id":"page","value":11.4,"unit":"oz","stated":"WEIGHT 11.4 oz / 323 g","source":{"type":"spec","publisher":"manufacturer","name":"HUXWRX Safety Co., FLOW 556 Ti product page","url":"https://huxwrx.com/flow-556-ti","retrieved":"2026-10-06","via":"harvest"}},{"id":"capitol","value":11.4,"unit":"oz","stated":"Weight: 11.4 oz","source":{"type":"spec","publisher":"retailer","name":"Capitol Armory, Huxwrx FLOW 556 Ti (HUX-556TI-3292; sold without a muzzle device)","url":"https://www.capitolarmory.com/huxwrx-flow-556-ti-titanium-556-ar15-rifle-silencer.html","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":11.4,"unit":"oz","stated":"Weight: 11.4 oz.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, HUXWRX FLOW 556 TI Suppressor - Black (SKU 3059, MPN 3059), Features","url":"https://www.primaryarms.com/huxwrx-flow-5-56-ti-suppressor-black","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"paper","reason":"The maker's own figure, in ounces and grams; its page and two sellers agree."},"note":"The can alone: the kit pages give the same 11.4 oz for the can and no weight with the flash hider in the box (3.3 oz more, by three sellers of it)."},"added_length":{"label":"What it adds to the weapon's length, by its maker (\"length added to barrel\")","kind":"length","measurements":[{"id":"paper","value":6.1,"unit":"in","stated":"LENGTH ADDED TO BARREL 6.1in / 15.5cm","source":{"type":"spec","publisher":"manufacturer","name":"HUXWRX Safety Co., FLOW 556 Ti white paper (\"LIGHTWEIGHT AND LONG-LASTING\"), one page: the dimensioned drawing and PRODUCT SPECIFICATIONS; references/huxwrx-flow-556-ti/docs/09a65d6ade.pdf","url":"https://huxwrx.com/content/white-paper/FLOW-556-Ti-White-Paper.pdf","retrieved":"2026-10-06","via":"harvest"}},{"id":"capitol","value":6.1,"unit":"in","stated":"Length: 6.8\" (adds 6.1\" to the barrel)","source":{"type":"spec","publisher":"retailer","name":"Capitol Armory, Huxwrx FLOW 556 Ti (HUX-556TI-3292; sold without a muzzle device)","url":"https://www.capitolarmory.com/huxwrx-flow-556-ti-titanium-556-ar15-rifle-silencer.html","retrieved":"2026-10-06","via":"harvest"}},{"id":"mile-high","value":6.1,"unit":"in","stated":"Length: 6.8 Inches Length Added to Barrel: 6.1 Inches Diameter: 1.80 Inches","source":{"type":"spec","publisher":"retailer","name":"Mile High Shooting, HUXWRX: Flow 556 TI + 556 QD 1/2x28 Flash Hider, Black (SKU 3292), Details and Features","url":"https://www.milehighshooting.com/huxwrx-flow-556-ti-556-qd-1-2x28-flash-hider-black/","retrieved":"2026-10-06","via":"harvest"}},{"id":"as-drawn","value":6.345,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{huxwrx-flash-hider-qd-556.suppressor_seat_x} + {.length} - {huxwrx-flash-hider-qd-556.thread_length}","via":"harvest"},"note":"The pair as drawn: the device's seat, the can's length ahead of it, less the 0.6 in of thread the maker states its devices' lengths for."}],"adopt":{"from":"paper","reason":"It is the maker's figure that this entry records; the pair as drawn stands 0.245 in longer (the hex plate's thickness, and a tenth more that the maker's rounding to a tenth could hold), and the conflict stays."},"note":"Given with no muzzle device named beside it; the same paper's MOUNTS row is \"556 QD Muzzle Brakes and Flash Hiders\", and both are 2.3 in long and add 1.7 \"on barrels with 0.6\\\" threads\" (the maker's pages for each). So: from the barrel's muzzle face to the can's front, on a QD device on a 0.6 in thread. In the maker's centimetres 17.2 less 15.5: 1.7 cm, 0.67 in, between the can's rear face and the muzzle face, which on a 0.6 in thread puts the rear face 0.07 in BEHIND the barrel's shoulder. As the two parts are drawn, the rear face stops on the device's hex plate, 0.145 in ahead of the shoulder (huxwrx-flash-hider-qd-556.suppressor_seat_x: the device's photo, and the maker's own rendering of a FLOW suppressor seated in the FLOW manual), and the can's front is 6.345 in ahead of the muzzle face: 0.245 in more than the maker's 6.1 (0.21 by its centimetres). The hex can't be inside the can (the can's mouth is its thread, 1.12 in; the hex is 1.20 across its corners)."},"grip_od":{"label":"Diameter over the base's grip texture","kind":"length","measurements":[{"id":"paper","value":1.85,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{.od} + {.grip_texture}","via":"harvest"}}],"note":"The body's diameter and what the paper says the texture adds to it. The drawing's outline is 1.85 in across at the length's scale (728 px at 393.7 px/in): the three published figures agree on it within 0.1%."},"collar_across_flats":{"label":"Mount end, the hex collar across its flats","kind":"length","measurements":[{"id":"drawing","value":1.3,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/huxwrx-flow-556-ti 1af30bbd3c1c (HUXWRX's white paper, FLOW 556 Ti: the page at 600 dpi, its side outline and its view of the muzzle end; vector art in the PDF)","scaleRef":"the drawing's own dimensioned length (6.8 in, 2677 px: 393.7 px/in), at which its outline is 1.85 in across over the grip texture and 1.81 on the smooth body, as published (1.8 and 0.05 more)","method":"tools/trace.py for the outline (the seed's trace spec) and .cache/hux/features.py for what is drawn inside it: positions in the drawing's own pixels from the collar's rear face and from the axis","via":"harvest"},"note":"The outline's height over x 0.03 to 0.19 in."}],"note":"The collar at the rear is a hexagon with rounded corners (Primary Arms' photos of the rear end; HUXWRX's manual: \"A wrench can also be used to remove the suppressor\"). The drawing's side view has a flat of it up and a flat down, so its height there is across the flats: the lines drawn on it are where the corners' rounds begin, 0.15 in either side of the middle and 0.15 in from each edge."},"collar_corner_r":{"label":"Mount end, the hex collar's corner radius","kind":"length","measurements":[{"id":"drawing","value":0.3,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/huxwrx-flow-556-ti 1af30bbd3c1c (HUXWRX's white paper, FLOW 556 Ti: the page at 600 dpi, its side outline and its view of the muzzle end; vector art in the PDF)","scaleRef":"the drawing's own dimensioned length (6.8 in, 2677 px: 393.7 px/in), at which its outline is 1.85 in across over the grip texture and 1.81 on the smooth body, as published (1.8 and 0.05 more)","method":"tools/trace.py for the outline (the seed's trace spec) and .cache/hux/features.py for what is drawn inside it: positions in the drawing's own pixels from the collar's rear face and from the axis","via":"harvest"},"note":"The same collar as the FLOW 556K's (its drawing has it 1.283 across at its own scale, this one 1.30): the lines where the rounds begin are drawn the same, 0.15 in from the middle."}]},"collar_length":{"label":"Mount end, the hex collar's length (to where the shoulder begins to widen)","kind":"length","measurements":[{"id":"drawing","value":0.237,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/huxwrx-flow-556-ti 1af30bbd3c1c (HUXWRX's white paper, FLOW 556 Ti: the page at 600 dpi, its side outline and its view of the muzzle end; vector art in the PDF)","scaleRef":"the drawing's own dimensioned length (6.8 in, 2677 px: 393.7 px/in), at which its outline is 1.85 in across over the grip texture and 1.81 on the smooth body, as published (1.8 and 0.05 more)","method":"tools/trace.py for the outline (the seed's trace spec) and .cache/hux/features.py for what is drawn inside it: positions in the drawing's own pixels from the collar's rear face and from the axis","via":"harvest"},"note":"Where the outline leaves the collar's straight edge."}]},"bore_d":{"label":"Bore, as it shows in the muzzle end","kind":"length","measurements":[{"id":"drawing","value":0.281,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/huxwrx-flow-556-ti 1af30bbd3c1c (HUXWRX's white paper, FLOW 556 Ti: the page at 600 dpi, its side outline and its view of the muzzle end; vector art in the PDF)","scaleRef":"the drawing's own dimensioned length (6.8 in, 2677 px: 393.7 px/in), at which its outline is 1.85 in across over the grip texture and 1.81 on the smooth body, as published (1.8 and 0.05 more)","method":"tools/trace.py for the outline (the seed's trace spec) and .cache/hux/features.py for what is drawn inside it: positions in the drawing's own pixels from the collar's rear face and from the axis","via":"harvest"},"note":"The circle at the middle of the end view, 55.5 px from its centre to the middle of its stroke."}]},"cap_slots":{"label":"Front cap, pockets round its shoulder, count","kind":"count","measurements":[{"id":"drawing","value":16,"unit":"count","source":{"type":"photo","photo":"references/huxwrx-flow-556-ti 1af30bbd3c1c (HUXWRX's white paper, FLOW 556 Ti: the page at 600 dpi, its side outline and its view of the muzzle end; vector art in the PDF)","scaleRef":"the drawing's own dimensioned length (6.8 in, 2677 px: 393.7 px/in), at which its outline is 1.85 in across over the grip texture and 1.81 on the smooth body, as published (1.8 and 0.05 more)","method":"tools/trace.py for the outline (the seed's trace spec) and .cache/hux/features.py for what is drawn inside it: positions in the drawing's own pixels from the collar's rear face and from the axis","via":"harvest"},"note":".cache/hux/fft.py: the end view's ink sampled round five circles between 0.70 and 0.93 of its radius; its harmonics there are 16, 32 and 48 and no others."}],"note":"Counted on the drawing's end view, which shows the whole turn, and on Mile High's photo of the muzzle end straight on (782c518318b9): sixteen scallops round the dished middle."},"cap_slot_r_in":{"label":"Front cap, where its pockets end toward the middle (radius in the end view)","kind":"length","measurements":[{"id":"drawing","value":0.645,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/huxwrx-flow-556-ti 1af30bbd3c1c (HUXWRX's white paper, FLOW 556 Ti: the page at 600 dpi, its side outline and its view of the muzzle end; vector art in the PDF)","scaleRef":"the drawing's own dimensioned length (6.8 in, 2677 px: 393.7 px/in), at which its outline is 1.85 in across over the grip texture and 1.81 on the smooth body, as published (1.8 and 0.05 more)","method":"tools/trace.py for the outline (the seed's trace spec) and .cache/hux/features.py for what is drawn inside it: positions in the drawing's own pixels from the collar's rear face and from the axis","via":"harvest"}}]},"cap_slot_r_out":{"label":"Front cap, where its pockets begin at the shoulder (radius in the end view)","kind":"length","measurements":[{"id":"drawing","value":0.87,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/huxwrx-flow-556-ti 1af30bbd3c1c (HUXWRX's white paper, FLOW 556 Ti: the page at 600 dpi, its side outline and its view of the muzzle end; vector art in the PDF)","scaleRef":"the drawing's own dimensioned length (6.8 in, 2677 px: 393.7 px/in), at which its outline is 1.85 in across over the grip texture and 1.81 on the smooth body, as published (1.8 and 0.05 more)","method":"tools/trace.py for the outline (the seed's trace spec) and .cache/hux/features.py for what is drawn inside it: positions in the drawing's own pixels from the collar's rear face and from the axis","via":"harvest"}}]},"cap_slot_width":{"label":"Front cap, a pocket's width","kind":"length","measurements":[{"id":"drawing","value":0.14,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/huxwrx-flow-556-ti 1af30bbd3c1c (HUXWRX's white paper, FLOW 556 Ti: the page at 600 dpi, its side outline and its view of the muzzle end; vector art in the PDF)","scaleRef":"the drawing's own dimensioned length (6.8 in, 2677 px: 393.7 px/in), at which its outline is 1.85 in across over the grip texture and 1.81 on the smooth body, as published (1.8 and 0.05 more)","method":"tools/trace.py for the outline (the seed's trace spec) and .cache/hux/features.py for what is drawn inside it: positions in the drawing's own pixels from the collar's rear face and from the axis","via":"harvest"},"note":"Across one pocket's loop on the end view at 600 dpi, read by eye."}]},"cap_slot_lean":{"label":"Front cap, how far its pockets lean from straight toward the middle, in the end view","kind":"angle","measurements":[{"id":"drawing","value":50,"unit":"deg","pm":10,"source":{"type":"photo","photo":"references/huxwrx-flow-556-ti 1af30bbd3c1c (HUXWRX's white paper, FLOW 556 Ti: the page at 600 dpi, its side outline and its view of the muzzle end; vector art in the PDF)","scaleRef":"the drawing's own dimensioned length (6.8 in, 2677 px: 393.7 px/in), at which its outline is 1.85 in across over the grip texture and 1.81 on the smooth body, as published (1.8 and 0.05 more)","method":"tools/trace.py for the outline (the seed's trace spec) and .cache/hux/features.py for what is drawn inside it: positions in the drawing's own pixels from the collar's rear face and from the axis","via":"harvest"},"note":"The pockets are long ovals lying well over from the radius, all the same way; read by eye on the end view at 600 dpi, and the photo of the muzzle end shows the same swirl."}]},"nose_rib_width":{"label":"Front cap, width of each of the three ribs that run from the bore to the pockets' ring","kind":"length","measurements":[{"id":"drawing","value":0.164,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/huxwrx-flow-556-ti 1af30bbd3c1c (HUXWRX's white paper, FLOW 556 Ti: the page at 600 dpi, its side outline and its view of the muzzle end; vector art in the PDF)","scaleRef":"the drawing's own dimensioned length (6.8 in, 2677 px: 393.7 px/in), at which its outline is 1.85 in across over the grip texture and 1.81 on the smooth body, as published (1.8 and 0.05 more)","method":"tools/trace.py for the outline (the seed's trace spec) and .cache/hux/features.py for what is drawn inside it: positions in the drawing's own pixels from the collar's rear face and from the axis","via":"harvest"}}],"note":"Round the bore the cap's middle is three flat sectors with a raised rib between each two (the end view's three bars and the three sectors between them; Mile High's photo of the muzzle end shows the ribs raised on a dished floor)."},"nose_boss_d":{"label":"Front cap, the boss round the bore where the ribs meet, diameter","kind":"length","measurements":[{"id":"drawing","value":0.38,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/huxwrx-flow-556-ti 1af30bbd3c1c (HUXWRX's white paper, FLOW 556 Ti: the page at 600 dpi, its side outline and its view of the muzzle end; vector art in the PDF)","scaleRef":"the drawing's own dimensioned length (6.8 in, 2677 px: 393.7 px/in), at which its outline is 1.85 in across over the grip texture and 1.81 on the smooth body, as published (1.8 and 0.05 more)","method":"tools/trace.py for the outline (the seed's trace spec) and .cache/hux/features.py for what is drawn inside it: positions in the drawing's own pixels from the collar's rear face and from the axis","via":"harvest"}}]},"grip_columns":{"label":"Grip texture, columns of dashes round the base","kind":"count","measurements":[{"id":"drawing","value":20,"unit":"count","source":{"type":"photo","photo":"references/huxwrx-flow-556-ti 1af30bbd3c1c (HUXWRX's white paper, FLOW 556 Ti: the page at 600 dpi, its side outline and its view of the muzzle end; vector art in the PDF)","scaleRef":"the drawing's own dimensioned length (6.8 in, 2677 px: 393.7 px/in), at which its outline is 1.85 in across over the grip texture and 1.81 on the smooth body, as published (1.8 and 0.05 more)","method":"tools/trace.py for the outline (the seed's trace spec) and .cache/hux/features.py for what is drawn inside it: positions in the drawing's own pixels from the collar's rear face and from the axis","via":"harvest"}}],"note":"Raised dashes along the can in columns round its rear third, every other column set forward of its neighbours. Twenty, by the dots the end view draws on its outer circle (the columns seen end-on): at 16, 35, 53, 70, 88, 106 degrees and so on, 17 to 19 degrees apart; on the side view the rows are 16 to 20 degrees apart round the near side."},"grip_ranks":{"label":"Grip texture, dashes in each column","kind":"count","measurements":[{"id":"drawing","value":3,"unit":"count","source":{"type":"photo","photo":"references/huxwrx-flow-556-ti 1af30bbd3c1c (HUXWRX's white paper, FLOW 556 Ti: the page at 600 dpi, its side outline and its view of the muzzle end; vector art in the PDF)","scaleRef":"the drawing's own dimensioned length (6.8 in, 2677 px: 393.7 px/in), at which its outline is 1.85 in across over the grip texture and 1.81 on the smooth body, as published (1.8 and 0.05 more)","method":"tools/trace.py for the outline (the seed's trace spec) and .cache/hux/features.py for what is drawn inside it: positions in the drawing's own pixels from the collar's rear face and from the axis","via":"harvest"}}]},"grip_first_x":{"label":"Grip texture, where the rearmost dashes begin, from the rear face","kind":"length","measurements":[{"id":"drawing","value":0.418,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/huxwrx-flow-556-ti 1af30bbd3c1c (HUXWRX's white paper, FLOW 556 Ti: the page at 600 dpi, its side outline and its view of the muzzle end; vector art in the PDF)","scaleRef":"the drawing's own dimensioned length (6.8 in, 2677 px: 393.7 px/in), at which its outline is 1.85 in across over the grip texture and 1.81 on the smooth body, as published (1.8 and 0.05 more)","method":"tools/trace.py for the outline (the seed's trace spec) and .cache/hux/features.py for what is drawn inside it: positions in the drawing's own pixels from the collar's rear face and from the axis","via":"harvest"},"note":"Every other column: 0.418 to 0.700 (it runs onto the shoulder), 1.105 to 1.463 and 1.790 to 2.193 in; the columns between: to 0.963, 1.306 to 1.666 and 1.985 to 2.409."}]},"grip_stagger":{"label":"Grip texture, how far every other column is set forward","kind":"length","measurements":[{"id":"drawing","value":0.2,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/huxwrx-flow-556-ti 1af30bbd3c1c (HUXWRX's white paper, FLOW 556 Ti: the page at 600 dpi, its side outline and its view of the muzzle end; vector art in the PDF)","scaleRef":"the drawing's own dimensioned length (6.8 in, 2677 px: 393.7 px/in), at which its outline is 1.85 in across over the grip texture and 1.81 on the smooth body, as published (1.8 and 0.05 more)","method":"tools/trace.py for the outline (the seed's trace spec) and .cache/hux/features.py for what is drawn inside it: positions in the drawing's own pixels from the collar's rear face and from the axis","via":"harvest"}}]},"grip_pitch":{"label":"Grip texture, from one dash to the next along a column","kind":"length","measurements":[{"id":"drawing","value":0.686,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/huxwrx-flow-556-ti 1af30bbd3c1c (HUXWRX's white paper, FLOW 556 Ti: the page at 600 dpi, its side outline and its view of the muzzle end; vector art in the PDF)","scaleRef":"the drawing's own dimensioned length (6.8 in, 2677 px: 393.7 px/in), at which its outline is 1.85 in across over the grip texture and 1.81 on the smooth body, as published (1.8 and 0.05 more)","method":"tools/trace.py for the outline (the seed's trace spec) and .cache/hux/features.py for what is drawn inside it: positions in the drawing's own pixels from the collar's rear face and from the axis","via":"harvest"}}]},"grip_dash_length":{"label":"Grip texture, a dash's length","kind":"length","measurements":[{"id":"drawing","value":0.38,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/huxwrx-flow-556-ti 1af30bbd3c1c (HUXWRX's white paper, FLOW 556 Ti: the page at 600 dpi, its side outline and its view of the muzzle end; vector art in the PDF)","scaleRef":"the drawing's own dimensioned length (6.8 in, 2677 px: 393.7 px/in), at which its outline is 1.85 in across over the grip texture and 1.81 on the smooth body, as published (1.8 and 0.05 more)","method":"tools/trace.py for the outline (the seed's trace spec) and .cache/hux/features.py for what is drawn inside it: positions in the drawing's own pixels from the collar's rear face and from the axis","via":"harvest"}}]},"grip_dash_width":{"label":"Grip texture, a dash's width","kind":"length","measurements":[{"id":"drawing","value":0.07,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/huxwrx-flow-556-ti 1af30bbd3c1c (HUXWRX's white paper, FLOW 556 Ti: the page at 600 dpi, its side outline and its view of the muzzle end; vector art in the PDF)","scaleRef":"the drawing's own dimensioned length (6.8 in, 2677 px: 393.7 px/in), at which its outline is 1.85 in across over the grip texture and 1.81 on the smooth body, as published (1.8 and 0.05 more)","method":"tools/trace.py for the outline (the seed's trace spec) and .cache/hux/features.py for what is drawn inside it: positions in the drawing's own pixels from the collar's rear face and from the axis","via":"harvest"},"note":"The dash facing the viewer: its inside 0.056 in between strokes, and a stroke's width more."}]}}},{"subject":"huxwrx-flow-556k","title":"HUXWRX FLOW 556K (2448 black, 2159 FDE)","dimensions":{"length":{"label":"Overall length, rear face to front face","kind":"length","measurements":[{"id":"paper","value":5.5,"unit":"in","stated":"5.5in / 14.0cm","source":{"type":"spec","publisher":"manufacturer","name":"HUXWRX Safety Co., FLOW 556k white paper (\"THE FIRST 3D-PRINTED FLOW-THROUGH® SUPPRESSOR\"), one page: the dimensioned drawing and PRODUCT SPECIFICATIONS; references/huxwrx-flow-556k/docs/27f4837be1.pdf","url":"https://huxwrx.com/content/white-paper/FLOW-556k-White-Paper.pdf","retrieved":"2026-10-06","via":"harvest"}},{"id":"page","value":5.5,"unit":"in","stated":"WEIGHT 12.9 oz LENGTH 5.5 in DIAMETER 1.6 in AVAILABLE IN BLACK & FDE","source":{"type":"spec","publisher":"manufacturer","name":"HUXWRX Safety Co., FLOW 556K product page","url":"https://huxwrx.com/flow-556k","retrieved":"2026-10-06","via":"harvest"}},{"id":"capitol","value":5.5,"unit":"in","stated":"It measures 5.5\" long with a 1.6\" diameter, adds 4.9\" to the barrel, and weighs 11.8 oz, with no barrel length restrictions.","source":{"type":"spec","publisher":"retailer","name":"Capitol Armory, HUXWRX FLOW 556k (HUX-OSS2450; sold without a muzzle device)","url":"https://www.capitolarmory.com/huxwrx-flow-556k.html","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"paper","reason":"The maker's drawing, with the figure on its dimension line; its page and a seller say the same."},"note":"The white paper's dimension line runs under the whole side outline, from the hex collar's rear face to the tip of the cap: the can alone, no muzzle device in it. In centimetres the paper says 14.0 (5.51 in)."},"od":{"label":"Largest outside diameter (the body; the grip texture at the base stands on it)","kind":"length","measurements":[{"id":"paper","value":1.6,"unit":"in","stated":"1.6in* 4.0cm*","source":{"type":"spec","publisher":"manufacturer","name":"HUXWRX Safety Co., FLOW 556k white paper (\"THE FIRST 3D-PRINTED FLOW-THROUGH® SUPPRESSOR\"), one page: the dimensioned drawing and PRODUCT SPECIFICATIONS; references/huxwrx-flow-556k/docs/27f4837be1.pdf","url":"https://huxwrx.com/content/white-paper/FLOW-556k-White-Paper.pdf","retrieved":"2026-10-06","via":"harvest"}},{"id":"page","value":1.6,"unit":"in","stated":"DIAMETER 1.6 in","source":{"type":"spec","publisher":"manufacturer","name":"HUXWRX Safety Co., FLOW 556K product page","url":"https://huxwrx.com/flow-556k","retrieved":"2026-10-06","via":"harvest"}},{"id":"capitol","value":1.6,"unit":"in","stated":"Diameter: 1.6\"","source":{"type":"spec","publisher":"retailer","name":"Capitol Armory, HUXWRX FLOW 556k (HUX-OSS2450; sold without a muzzle device)","url":"https://www.capitolarmory.com/huxwrx-flow-556k.html","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"paper","reason":"The maker's drawing; its page and a seller say the same."},"note":"The paper's 1.6 in is starred: \"*Base grip texture adds 0.05in (0.127cm)\" (grip_texture). In centimetres 4.0 (1.575 in), and the drawing's own body is 1.58 at the scale its length gives."},"grip_texture":{"label":"What the base's grip texture adds to the diameter","kind":"length","measurements":[{"id":"paper","value":0.05,"unit":"in","pm":0.005,"stated":"*Base grip texture adds 0.05in (0.127cm)","source":{"type":"spec","publisher":"manufacturer","name":"HUXWRX Safety Co., FLOW 556k white paper (\"THE FIRST 3D-PRINTED FLOW-THROUGH® SUPPRESSOR\"), one page: the dimensioned drawing and PRODUCT SPECIFICATIONS; references/huxwrx-flow-556k/docs/27f4837be1.pdf","url":"https://huxwrx.com/content/white-paper/FLOW-556k-White-Paper.pdf","retrieved":"2026-10-06","via":"harvest"}}]},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"paper","value":12.9,"unit":"oz","stated":"12.9oz / 366g","source":{"type":"spec","publisher":"manufacturer","name":"HUXWRX Safety Co., FLOW 556k white paper (\"THE FIRST 3D-PRINTED FLOW-THROUGH® SUPPRESSOR\"), one page: the dimensioned drawing and PRODUCT SPECIFICATIONS; references/huxwrx-flow-556k/docs/27f4837be1.pdf","url":"https://huxwrx.com/content/white-paper/FLOW-556k-White-Paper.pdf","retrieved":"2026-10-06","via":"harvest"}},{"id":"page","value":12.9,"unit":"oz","stated":"WEIGHT 12.9 oz","source":{"type":"spec","publisher":"manufacturer","name":"HUXWRX Safety Co., FLOW 556K product page","url":"https://huxwrx.com/flow-556k","retrieved":"2026-10-06","via":"harvest"}},{"id":"capitol","value":11.8,"unit":"oz","stated":"Weight: 11.8 oz","source":{"type":"spec","publisher":"retailer","name":"Capitol Armory, HUXWRX FLOW 556k (HUX-OSS2450; sold without a muzzle device)","url":"https://www.capitolarmory.com/huxwrx-flow-556k.html","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms-kit","value":11.9,"unit":"oz","stated":"Weight 11.9 oz.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, HUXWRX FLOW 556K Suppressor with QD 1/2x28 Flash Hider - Black (2449), Specifications table (the table's \"Length 5.5 in.\" is the can's, so this is read as the can's weight too)","url":"https://www.primaryarms.com/huxwrx-flow-556k-suppressor-with-qd-556-1-2x28-flash-hider-black","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"paper","reason":"The maker's own figure, twice (its white paper, in ounces and grams, and its page). Two sellers say 11.8 and 11.9 oz and give no account of the difference: kept, and the conflict stays."},"note":"The maker's 12.9 oz (366 g) against sellers' 11.8 and 11.9, 1.1 oz apart; no page says what the lighter figure weighed. Primary Arms' page for the can alone prints both as a range (\"Weight: 11.8 - 12.9 oz.\") and Mile High's kit page \"Weight: 11.9 - 12.9oz / 366g\": neither is one reading, and neither is recorded as one. Primary Arms' table on the can-alone page says \"Weight 3.3 oz.\" and \"Length 2.3 in.\": those are the flash hider's (its ledger has them)."},"added_length":{"label":"What it adds to the weapon's length, by its maker (\"length added to barrel\")","kind":"length","measurements":[{"id":"paper","value":4.9,"unit":"in","stated":"LENGTH ADDED TO BARREL 4.9in / 12.4cm","source":{"type":"spec","publisher":"manufacturer","name":"HUXWRX Safety Co., FLOW 556k white paper (\"THE FIRST 3D-PRINTED FLOW-THROUGH® SUPPRESSOR\"), one page: the dimensioned drawing and PRODUCT SPECIFICATIONS; references/huxwrx-flow-556k/docs/27f4837be1.pdf","url":"https://huxwrx.com/content/white-paper/FLOW-556k-White-Paper.pdf","retrieved":"2026-10-06","via":"harvest"}},{"id":"capitol","value":4.9,"unit":"in","stated":"Length: 5.5\" (adds 4.9\" to the barrel)","source":{"type":"spec","publisher":"retailer","name":"Capitol Armory, HUXWRX FLOW 556k (HUX-OSS2450; sold without a muzzle device)","url":"https://www.capitolarmory.com/huxwrx-flow-556k.html","retrieved":"2026-10-06","via":"harvest"}},{"id":"as-drawn","value":5.045,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{huxwrx-flash-hider-qd-556.suppressor_seat_x} + {.length} - {huxwrx-flash-hider-qd-556.thread_length}","via":"harvest"},"note":"The pair as drawn: the device's seat, the can's length ahead of it, less the 0.6 in of thread the maker states its devices' lengths for."}],"adopt":{"from":"paper","reason":"It is the maker's figure that this entry records; the pair as drawn stands 0.145 in longer, by the hex plate's thickness, and the conflict stays."},"note":"Given with no muzzle device named beside it; the same paper's MOUNTS row is \"556 QD Muzzle Brakes and Flash Hiders\", and both are 2.3 in long and add 1.7 \"on barrels with 0.6\\\" threads\" (the maker's pages for each). So: from the barrel's muzzle face to the can's front, on a QD device on a 0.6 in thread. In the maker's centimetres 14.0 less 12.4: 1.6 cm, 0.63 in, between the can's rear face and the muzzle face, which on a 0.6 in thread puts the rear face 0.03 in BEHIND the barrel's shoulder. As the two parts are drawn, the rear face stops on the device's hex plate, 0.145 in ahead of the shoulder (huxwrx-flash-hider-qd-556.suppressor_seat_x: the device's photo, and the maker's own rendering of the pair seated in the FLOW manual), and the can's front is 5.045 in ahead of the muzzle face: 0.145 in more than the maker's 4.9. The hex can't be inside the can (the can's mouth is its thread, 1.12 in; the hex is 1.20 across its corners). Read as the can's length less the thread and nothing for the hex, the maker's figure is exact (5.5 - 0.6). Primary Arms adds \"3.8\\\" length added to the muzzle device\", which is 5.5 less 1.7 and no measurement of anything."},"grip_od":{"label":"Diameter over the base's grip texture","kind":"length","measurements":[{"id":"paper","value":1.65,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{.od} + {.grip_texture}","via":"harvest"}}],"note":"The body's diameter and what the paper says the texture adds to it. The drawing's outline is 1.60 in across where dashes fall near its edge and 1.587 on the smooth body."},"collar_across_flats":{"label":"Mount end, the hex collar across its flats","kind":"length","measurements":[{"id":"drawing","value":1.283,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/huxwrx-flow-556k d9decdd1e19b (HUXWRX's white paper, FLOW 556k: the page at 600 dpi, its side outline and its view of the muzzle end; vector art in the PDF)","scaleRef":"the drawing's own dimensioned length (5.5 in, 2492 px) and diameter (1.6 in, 727 px), which agree within 0.3%: 453.7 px/in","method":"tools/trace.py for the outline (the seed's trace spec) and .cache/hux/features.py for what is drawn inside it: positions in the drawing's own pixels from the collar's rear face and from the axis","via":"harvest"},"note":"The outline's height over x 0.03 to 0.19 in."}],"note":"The collar at the rear is a hexagon with rounded corners (Primary Arms' photos of the rear end; HUXWRX's manual: \"A wrench can also be used to remove the suppressor\"). The drawing's side view has a flat of it up and a flat down, so its height there is across the flats: the lines drawn on it are where the corners' rounds begin, 0.15 in either side of the middle and 0.15 in from each edge."},"collar_corner_r":{"label":"Mount end, the hex collar's corner radius","kind":"length","measurements":[{"id":"drawing","value":0.3,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/huxwrx-flow-556k d9decdd1e19b (HUXWRX's white paper, FLOW 556k: the page at 600 dpi, its side outline and its view of the muzzle end; vector art in the PDF)","scaleRef":"the drawing's own dimensioned length (5.5 in, 2492 px) and diameter (1.6 in, 727 px), which agree within 0.3%: 453.7 px/in","method":"tools/trace.py for the outline (the seed's trace spec) and .cache/hux/features.py for what is drawn inside it: positions in the drawing's own pixels from the collar's rear face and from the axis","via":"harvest"},"note":"Half the round's radius is how far its tangent line stands from the corner's own line, seen across a flat that leans 60 degrees: the lines are 0.15 in from the middle (34 px at 227 px/in on the page at 300 dpi), so 0.30 in."}]},"collar_length":{"label":"Mount end, the hex collar's length (to where the shoulder begins to widen)","kind":"length","measurements":[{"id":"drawing","value":0.244,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/huxwrx-flow-556k d9decdd1e19b (HUXWRX's white paper, FLOW 556k: the page at 600 dpi, its side outline and its view of the muzzle end; vector art in the PDF)","scaleRef":"the drawing's own dimensioned length (5.5 in, 2492 px) and diameter (1.6 in, 727 px), which agree within 0.3%: 453.7 px/in","method":"tools/trace.py for the outline (the seed's trace spec) and .cache/hux/features.py for what is drawn inside it: positions in the drawing's own pixels from the collar's rear face and from the axis","via":"harvest"},"note":"Where the outline leaves the collar's straight edge."}]},"bore_d":{"label":"Bore, as it shows in the muzzle end","kind":"length","measurements":[{"id":"drawing","value":0.277,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/huxwrx-flow-556k d9decdd1e19b (HUXWRX's white paper, FLOW 556k: the page at 600 dpi, its side outline and its view of the muzzle end; vector art in the PDF)","scaleRef":"the drawing's own dimensioned length (5.5 in, 2492 px) and diameter (1.6 in, 727 px), which agree within 0.3%: 453.7 px/in","method":"tools/trace.py for the outline (the seed's trace spec) and .cache/hux/features.py for what is drawn inside it: positions in the drawing's own pixels from the collar's rear face and from the axis","via":"harvest"},"note":"The circle at the middle of the end view, 63 px from its centre to the middle of its stroke."}]},"cap_slots":{"label":"Front cap, pockets round its shoulder, count","kind":"count","measurements":[{"id":"drawing","value":18,"unit":"count","source":{"type":"photo","photo":"references/huxwrx-flow-556k d9decdd1e19b (HUXWRX's white paper, FLOW 556k: the page at 600 dpi, its side outline and its view of the muzzle end; vector art in the PDF)","scaleRef":"the drawing's own dimensioned length (5.5 in, 2492 px) and diameter (1.6 in, 727 px), which agree within 0.3%: 453.7 px/in","method":"tools/trace.py for the outline (the seed's trace spec) and .cache/hux/features.py for what is drawn inside it: positions in the drawing's own pixels from the collar's rear face and from the axis","via":"harvest"},"note":".cache/hux/fft.py: the end view's ink sampled round five circles between 0.70 and 0.93 of its radius; its harmonics there are 18, 36 and 54 and no others."}],"note":"Counted on the drawing's end view, which shows the whole turn. On the maker's photo of the can in FDE (1964a643ceef) nine show on the near half."},"cap_slot_r_in":{"label":"Front cap, where its pockets end toward the middle (radius in the end view)","kind":"length","measurements":[{"id":"drawing","value":0.52,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/huxwrx-flow-556k d9decdd1e19b (HUXWRX's white paper, FLOW 556k: the page at 600 dpi, its side outline and its view of the muzzle end; vector art in the PDF)","scaleRef":"the drawing's own dimensioned length (5.5 in, 2492 px) and diameter (1.6 in, 727 px), which agree within 0.3%: 453.7 px/in","method":"tools/trace.py for the outline (the seed's trace spec) and .cache/hux/features.py for what is drawn inside it: positions in the drawing's own pixels from the collar's rear face and from the axis","via":"harvest"}}]},"cap_slot_r_out":{"label":"Front cap, where its pockets begin at the shoulder (radius in the end view)","kind":"length","measurements":[{"id":"drawing","value":0.77,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/huxwrx-flow-556k d9decdd1e19b (HUXWRX's white paper, FLOW 556k: the page at 600 dpi, its side outline and its view of the muzzle end; vector art in the PDF)","scaleRef":"the drawing's own dimensioned length (5.5 in, 2492 px) and diameter (1.6 in, 727 px), which agree within 0.3%: 453.7 px/in","method":"tools/trace.py for the outline (the seed's trace spec) and .cache/hux/features.py for what is drawn inside it: positions in the drawing's own pixels from the collar's rear face and from the axis","via":"harvest"}}]},"cap_slot_width":{"label":"Front cap, a pocket's width","kind":"length","measurements":[{"id":"drawing","value":0.125,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/huxwrx-flow-556k d9decdd1e19b (HUXWRX's white paper, FLOW 556k: the page at 600 dpi, its side outline and its view of the muzzle end; vector art in the PDF)","scaleRef":"the drawing's own dimensioned length (5.5 in, 2492 px) and diameter (1.6 in, 727 px), which agree within 0.3%: 453.7 px/in","method":"tools/trace.py for the outline (the seed's trace spec) and .cache/hux/features.py for what is drawn inside it: positions in the drawing's own pixels from the collar's rear face and from the axis","via":"harvest"},"note":"Across one pocket's loop on the end view at 600 dpi, read by eye."}]},"cap_slot_lean":{"label":"Front cap, how far its pockets lean from straight toward the middle, in the end view","kind":"angle","measurements":[{"id":"drawing","value":15,"unit":"deg","pm":10,"source":{"type":"photo","photo":"references/huxwrx-flow-556k d9decdd1e19b (HUXWRX's white paper, FLOW 556k: the page at 600 dpi, its side outline and its view of the muzzle end; vector art in the PDF)","scaleRef":"the drawing's own dimensioned length (5.5 in, 2492 px) and diameter (1.6 in, 727 px), which agree within 0.3%: 453.7 px/in","method":"tools/trace.py for the outline (the seed's trace spec) and .cache/hux/features.py for what is drawn inside it: positions in the drawing's own pixels from the collar's rear face and from the axis","via":"harvest"},"note":"Each pocket's loop leans a little from the radius; read by eye on the end view at 600 dpi."}]},"nose_rib_width":{"label":"Front cap, width of each of the three ribs that run from the bore to the pockets' ring","kind":"length","measurements":[{"id":"drawing","value":0.154,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/huxwrx-flow-556k d9decdd1e19b (HUXWRX's white paper, FLOW 556k: the page at 600 dpi, its side outline and its view of the muzzle end; vector art in the PDF)","scaleRef":"the drawing's own dimensioned length (5.5 in, 2492 px) and diameter (1.6 in, 727 px), which agree within 0.3%: 453.7 px/in","method":"tools/trace.py for the outline (the seed's trace spec) and .cache/hux/features.py for what is drawn inside it: positions in the drawing's own pixels from the collar's rear face and from the axis","via":"harvest"}}],"note":"Round the bore the cap's middle is three flat sectors with a raised rib between each two (the end view's three bars and the three sectors between them; the maker's photos show the ribs standing on a pointed nose)."},"nose_boss_d":{"label":"Front cap, the boss round the bore where the ribs meet, diameter","kind":"length","measurements":[{"id":"drawing","value":0.44,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/huxwrx-flow-556k d9decdd1e19b (HUXWRX's white paper, FLOW 556k: the page at 600 dpi, its side outline and its view of the muzzle end; vector art in the PDF)","scaleRef":"the drawing's own dimensioned length (5.5 in, 2492 px) and diameter (1.6 in, 727 px), which agree within 0.3%: 453.7 px/in","method":"tools/trace.py for the outline (the seed's trace spec) and .cache/hux/features.py for what is drawn inside it: positions in the drawing's own pixels from the collar's rear face and from the axis","via":"harvest"}}]},"grip_columns":{"label":"Grip texture, columns of dashes round the base","kind":"count","measurements":[{"id":"drawing","value":20,"unit":"count","source":{"type":"photo","photo":"references/huxwrx-flow-556k d9decdd1e19b (HUXWRX's white paper, FLOW 556k: the page at 600 dpi, its side outline and its view of the muzzle end; vector art in the PDF)","scaleRef":"the drawing's own dimensioned length (5.5 in, 2492 px) and diameter (1.6 in, 727 px), which agree within 0.3%: 453.7 px/in","method":"tools/trace.py for the outline (the seed's trace spec) and .cache/hux/features.py for what is drawn inside it: positions in the drawing's own pixels from the collar's rear face and from the axis","via":"harvest"}}],"note":"Raised dashes along the can in columns round its rear third, every other column set forward of its neighbours. Twenty, by the dots the end view draws on its outer circle (the columns seen end-on): at 6, 26, 42, 62, 78, 98 degrees and so on, 20 and 16 degrees apart by turns; on the side view the rows are 16 to 20 degrees apart round the near side."},"grip_ranks":{"label":"Grip texture, dashes in each column","kind":"count","measurements":[{"id":"drawing","value":3,"unit":"count","source":{"type":"photo","photo":"references/huxwrx-flow-556k d9decdd1e19b (HUXWRX's white paper, FLOW 556k: the page at 600 dpi, its side outline and its view of the muzzle end; vector art in the PDF)","scaleRef":"the drawing's own dimensioned length (5.5 in, 2492 px) and diameter (1.6 in, 727 px), which agree within 0.3%: 453.7 px/in","method":"tools/trace.py for the outline (the seed's trace spec) and .cache/hux/features.py for what is drawn inside it: positions in the drawing's own pixels from the collar's rear face and from the axis","via":"harvest"}}]},"grip_first_x":{"label":"Grip texture, where the rearmost dashes begin, from the rear face","kind":"length","measurements":[{"id":"drawing","value":0.405,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/huxwrx-flow-556k d9decdd1e19b (HUXWRX's white paper, FLOW 556k: the page at 600 dpi, its side outline and its view of the muzzle end; vector art in the PDF)","scaleRef":"the drawing's own dimensioned length (5.5 in, 2492 px) and diameter (1.6 in, 727 px), which agree within 0.3%: 453.7 px/in","method":"tools/trace.py for the outline (the seed's trace spec) and .cache/hux/features.py for what is drawn inside it: positions in the drawing's own pixels from the collar's rear face and from the axis","via":"harvest"},"note":"Every other column: 0.405 to 0.751, 1.081 to 1.434 and 1.747 to 2.143 in; the columns between: 0.593 to 0.941, 1.271 to 1.621 and 1.932 to 2.344."}]},"grip_stagger":{"label":"Grip texture, how far every other column is set forward","kind":"length","measurements":[{"id":"drawing","value":0.188,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/huxwrx-flow-556k d9decdd1e19b (HUXWRX's white paper, FLOW 556k: the page at 600 dpi, its side outline and its view of the muzzle end; vector art in the PDF)","scaleRef":"the drawing's own dimensioned length (5.5 in, 2492 px) and diameter (1.6 in, 727 px), which agree within 0.3%: 453.7 px/in","method":"tools/trace.py for the outline (the seed's trace spec) and .cache/hux/features.py for what is drawn inside it: positions in the drawing's own pixels from the collar's rear face and from the axis","via":"harvest"}}]},"grip_pitch":{"label":"Grip texture, from one dash to the next along a column","kind":"length","measurements":[{"id":"drawing","value":0.672,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/huxwrx-flow-556k d9decdd1e19b (HUXWRX's white paper, FLOW 556k: the page at 600 dpi, its side outline and its view of the muzzle end; vector art in the PDF)","scaleRef":"the drawing's own dimensioned length (5.5 in, 2492 px) and diameter (1.6 in, 727 px), which agree within 0.3%: 453.7 px/in","method":"tools/trace.py for the outline (the seed's trace spec) and .cache/hux/features.py for what is drawn inside it: positions in the drawing's own pixels from the collar's rear face and from the axis","via":"harvest"}}]},"grip_dash_length":{"label":"Grip texture, a dash's length","kind":"length","measurements":[{"id":"drawing","value":0.36,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/huxwrx-flow-556k d9decdd1e19b (HUXWRX's white paper, FLOW 556k: the page at 600 dpi, its side outline and its view of the muzzle end; vector art in the PDF)","scaleRef":"the drawing's own dimensioned length (5.5 in, 2492 px) and diameter (1.6 in, 727 px), which agree within 0.3%: 453.7 px/in","method":"tools/trace.py for the outline (the seed's trace spec) and .cache/hux/features.py for what is drawn inside it: positions in the drawing's own pixels from the collar's rear face and from the axis","via":"harvest"}}]},"grip_dash_width":{"label":"Grip texture, a dash's width","kind":"length","measurements":[{"id":"drawing","value":0.065,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/huxwrx-flow-556k d9decdd1e19b (HUXWRX's white paper, FLOW 556k: the page at 600 dpi, its side outline and its view of the muzzle end; vector art in the PDF)","scaleRef":"the drawing's own dimensioned length (5.5 in, 2492 px) and diameter (1.6 in, 727 px), which agree within 0.3%: 453.7 px/in","method":"tools/trace.py for the outline (the seed's trace spec) and .cache/hux/features.py for what is drawn inside it: positions in the drawing's own pixels from the collar's rear face and from the axis","via":"harvest"},"note":"The dash facing the viewer: its inside 0.053 in between strokes, and a stroke's width more."}]}}},{"subject":"jp-silent-captured-spring-gen2-h2","title":"JP Enterprises Silent Captured Spring AR-15 Heavy H2 GEN 2","dimensions":{"weight":{"label":"Weight (the whole unit)","kind":"mass","measurements":[{"id":"jp","value":6.9,"unit":"oz","pm":0.05,"stated":"Weight: 6.9 oz.","source":{"type":"spec","publisher":"manufacturer","name":"JP Enterprises, GEN 2 Silent Captured Spring System for AR-15 type rifle with H2 heavy buffer #JPSCS2-15H2 (the maker's store page)","url":"https://jprifles.com/buy_test.php?item=JPSCS2-15H2","retrieved":"2026-10-18","via":"harvest"}},{"id":"primary-arms","value":6.9,"unit":"oz","pm":0.05,"stated":"Brand JP Enterprises Buffer H2 Carbine Platform AR-15 Weight 6.9 oz.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, JP Enterprises SCS Silent Capture Spring Gen 2 AR-15 H2 Buffer - Carbine/Rifle","url":"https://www.primaryarms.com/JPSCS2-15H2","retrieved":"2026-10-18","via":"harvest"}},{"id":"silencershop","value":6.9,"unit":"oz","pm":0.05,"stated":"Technical Specifications: Weight: 6.9 oz","source":{"type":"spec","publisher":"retailer","name":"Silencer Shop, JP Gen 2 Silent Captured Spring Heavy Buffer - AR15","url":"https://www.silencershop.com/jp-gen-2-silent-captured-spring-heavy-buffer-ar15.html","retrieved":"2026-10-18","via":"harvest"}},{"id":"ar15discounts","value":8.96,"unit":"oz","pm":0.005,"stated":"Additional information Weight 8.96 oz MPN JPSCS2-15H2 UPC 812872023984","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, JP Enterprises Gen 2 Silent Capture Spring w/ H2 Buffer - AR-15","url":"https://ar15discounts.com/products/jp-enterprises-gen-2-silent-capture-spring-w-h2-buffer-ar-15/","retrieved":"2026-10-18","via":"harvest"},"note":"A shop's field, 2 oz over the maker's: the box with its spacer, by the standard's page at the same shop (6.24 oz against JP's 5.3)."}],"adopt":{"from":"jp","reason":"The maker's figure, and two sellers' the same. AR15Discounts' shop field is the product as shipped, as its field for the standard is."}},"buffering_mass":{"label":"The buffer's mass: the slider with its weights, which the carrier drives (what a buffer's class is)","kind":"mass","measurements":[{"id":"jp","value":4.8,"unit":"oz","pm":0.05,"stated":"Buffering/Reciprocating Mass: 4.8 oz. (Ideal for replacing a standard buffer of the same weight)","source":{"type":"spec","publisher":"manufacturer","name":"JP Enterprises, GEN 2 Silent Captured Spring System for AR-15 type rifle with H2 heavy buffer #JPSCS2-15H2 (the maker's store page)","url":"https://jprifles.com/buy_test.php?item=JPSCS2-15H2","retrieved":"2026-10-18","via":"harvest"},"note":"JP's FAQ table: \"2 Tungsten | 1 Steel (H2) 4.8 oz. JPSCS2-15H2\" (https://jprifles.com/1.4.7.2_os.php?menu_select=scs_guide). Over the standard's 2.9 oz it is 0.95 oz a tungsten weight; the unit's weight over the standard's, 6.9 against 5.3, is 0.80."}]},"tungsten_count":{"label":"Of the three weights, how many are tungsten (the front ones; the rearmost is steel)","kind":"count","measurements":[{"id":"jp","value":2,"unit":"count","stated":"2 Tungsten | 1 Steel (H2) 4.8 oz. JPSCS2-15H2","source":{"type":"spec","publisher":"manufacturer","name":"JP Enterprises, Buffer Springs and Silent Captured Springs (FAQ: SCS Mass Configuration)","url":"https://jprifles.com/1.4.7.2_os.php?menu_select=scs_guide","retrieved":"2026-10-18","via":"harvest"}}],"note":"Which: in Primary Arms' photo from ahead (708eab533a4c) the two weights behind the flange are a dark grey and the one next to the collar bright steel; JP's own picture (c5a3ef37c597) has them so."},"coils":{"label":"The spring's turns between the collar and the bumper (JP's 15-100)","kind":"count","measurements":[{"id":"photo","value":25,"unit":"count","pm":1,"source":{"type":"photo","photo":"references/jp-silent-captured-spring-gen2-h2 708eab533a4c (Primary Arms' JPSCS2-15H2_01, 2200 x 1467, the H2 from ahead of its front face)","scaleRef":"none: a count","method":"the photo levelled along the unit's axis (turned 27.4 degrees), the crests along the spring's lower edge from the bumper (px 606) to the collar (px 1495): 25, 33 to 40 px apart as the spring nears the lens","via":"harvest"}}],"note":"JP's kit sheet: \"JPSCS-15-100** Uncolored\" with \"** JPSCS2-15H2\" (https://jprifles.com/document_pdfs/JPSCS2%20Kit_911.pdf): a heavier spring than the standard's 15-85, and fewer turns where it shows."},"front_bore_d":{"label":"Diameter of the bore in the slider's front face (the guide rod's screw is at its bottom)","kind":"length","measurements":[{"id":"photo","value":0.546,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/jp-silent-captured-spring-gen2-h2 708eab533a4c (Primary Arms' JPSCS2-15H2_01, the H2 from ahead of its front face)","scaleRef":"the flange's own diameter (.flange_d) across the face's ellipse","method":"the bore's long axis over the flange's along the same line, 0.55: a ratio along an ellipse's long axis is true whatever the lean","via":"harvest"},"note":"The standard's ledger holds the same reading of this photo, the slider being one."}]},"cap_pocket_d":{"label":"The pocket in the end cap's rear face that the rear screw's head sits in","kind":"length","measurements":[{"id":"photo","value":0.42,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/jp-silent-captured-spring-gen2-h2 0c20449e5d5c (Primary Arms' JPSCS2-15H2_02, the H2 from behind its end cap, \"US 8,800,424\" on its face)","scaleRef":"the cap's own diameter (.cap_d) across the face's ellipse","method":"the pocket's long axis over the face's along the same line, 0.42, on a crop at twice the size","via":"harvest"}}]},"screw_head_d":{"label":"The rear screw's head","kind":"length","measurements":[{"id":"photo","value":0.36,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/jp-silent-captured-spring-gen2-h2 0c20449e5d5c","scaleRef":"the cap's own diameter (.cap_d) across the face's ellipse","method":"the head's long axis inside the pocket over the face's, 0.36","via":"harvest"}}]},"flange_d":{"label":"Diameter of the slider's front flange (black), the face the carrier bears on","kind":"length","measurements":[{"id":"standard","value":0.993,"unit":"in","pm":0.016,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.flange_d}","via":"harvest"},"note":"The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H2 gives this one."}]},"flange_length":{"label":"Length of the front flange","kind":"length","measurements":[{"id":"standard","value":0.209,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.flange_length}","via":"harvest"},"note":"The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H2 gives this one."}]},"flange_round":{"label":"The round on the flange's front edge","kind":"length","measurements":[{"id":"standard","value":0.045,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.flange_round}","via":"harvest"},"note":"The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H2 gives this one."}]},"oring_gap":{"label":"Width of each O-ring's band between the flange and a weight and between two weights","kind":"length","measurements":[{"id":"standard","value":0.072,"unit":"in","pm":0.016,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.oring_gap}","via":"harvest"},"note":"The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H2 gives this one."}]},"oring_d":{"label":"Diameter of the O-rings as they show between the weights","kind":"length","measurements":[{"id":"standard","value":0.942,"unit":"in","pm":0.016,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.oring_d}","via":"harvest"},"note":"The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H2 gives this one."}]},"od":{"label":"Diameter of the three weights (the buffer's widest steel)","kind":"length","measurements":[{"id":"standard","value":0.966,"unit":"in","pm":0.016,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.od}","via":"harvest"},"note":"The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H2 gives this one."}]},"mass_length":{"label":"Length of one weight","kind":"length","measurements":[{"id":"standard","value":0.572,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.mass_length}","via":"harvest"},"note":"The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H2 gives this one."}]},"mass_chamfer":{"label":"The break on each weight's edges","kind":"length","measurements":[{"id":"standard","value":0.014,"unit":"in","pm":0.007,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.mass_chamfer}","via":"harvest"},"note":"The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H2 gives this one."}]},"mass_count":{"label":"Weights on the slider","kind":"count","measurements":[{"id":"standard","value":3,"unit":"count","source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.mass_count}","via":"harvest"},"note":"The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H2 gives this one."}]},"snap_ring_length":{"label":"Width of the snap ring's band behind the rearmost weight","kind":"length","measurements":[{"id":"standard","value":0.062,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.snap_ring_length}","via":"harvest"},"note":"The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H2 gives this one."}]},"snap_ring_d":{"label":"Diameter of the snap ring as it shows","kind":"length","measurements":[{"id":"standard","value":0.897,"unit":"in","pm":0.025,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.snap_ring_d}","via":"harvest"},"note":"The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H2 gives this one."}]},"collar_d":{"label":"Diameter of the slider's black rear collar, which the spring bears on","kind":"length","measurements":[{"id":"standard","value":0.805,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.collar_d}","via":"harvest"},"note":"The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H2 gives this one."}]},"collar_length":{"label":"Length of the rear collar","kind":"length","measurements":[{"id":"standard","value":0.164,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.collar_length}","via":"harvest"},"note":"The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H2 gives this one."}]},"mass_bore_d":{"label":"Bore of the weights (the slider's tube under them)","kind":"length","measurements":[{"id":"standard","value":0.805,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.mass_bore_d}","via":"harvest"},"note":"The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H2 gives this one."}]},"front_bore_depth":{"label":"Depth of that bore to the screw's head (unit out of the rifle)","kind":"length","measurements":[{"id":"standard","value":0.25,"unit":"in","pm":0.1,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.front_bore_depth}","via":"harvest"},"note":"The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H2 gives this one."}]},"inner_flange":{"label":"The slider's inner flange: how thick it is, behind the front bore (the front screw's head bears on it from ahead, the spring from behind)","kind":"length","measurements":[{"id":"standard","value":0.1,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.inner_flange}","via":"harvest"},"note":"The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H2 gives this one."}]},"slider_bore_d":{"label":"Bore through the slider from its rear to its inner flange, which the spring's front end goes into (and the bumper's, which its rear end goes into)","kind":"length","measurements":[{"id":"standard","value":0.53,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.slider_bore_d}","via":"harvest"},"note":"The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H2 gives this one."}]},"length":{"label":"Length out of the rifle (the slider's front face to the end cap's rear face)","kind":"length","measurements":[{"id":"standard","value":7.249,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.length}","via":"harvest"},"note":"The standard unit's figure: the unit's length, the guide rod and its screws are the standard GEN 2's, and no photo of the H2 gives this one."}]},"installed_length":{"label":"The unit's length in the rifle, bolt forward (the slider's front face on the carrier to the extension's rear wall)","kind":"length","measurements":[{"id":"standard","value":7.226,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.installed_length}","via":"harvest"},"note":"The standard unit's figure: the unit's length, the guide rod and its screws are the standard GEN 2's, and no photo of the H2 gives this one."}]},"protrusion":{"label":"How far the unit stands out of the extension past the lower's face with the receivers open","kind":"length","measurements":[{"id":"standard","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.protrusion}","via":"harvest"},"note":"The standard unit's figure: the unit's length, the guide rod and its screws are the standard GEN 2's, and no photo of the H2 gives this one."}]},"rod_d":{"label":"Diameter of the guide rod (aluminium)","kind":"length","measurements":[{"id":"standard","value":0.377,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.rod_d}","via":"harvest"},"note":"The standard unit's figure: the unit's length, the guide rod and its screws are the standard GEN 2's, and no photo of the H2 gives this one."}]},"carrier_channel_min":{"label":"The narrowest rear channel of a bolt carrier the guide rod passes into while cycling","kind":"length","measurements":[{"id":"standard","value":0.53,"unit":"in","pm":0.0005,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.carrier_channel_min}","via":"harvest"},"note":"The standard unit's figure: the unit's length, the guide rod and its screws are the standard GEN 2's, and no photo of the H2 gives this one."}]},"hex_socket":{"label":"The screws' hex socket, across its flats","kind":"length","measurements":[{"id":"standard","value":0.125,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.hex_socket}","via":"harvest"},"note":"The standard unit's figure: the unit's length, the guide rod and its screws are the standard GEN 2's, and no photo of the H2 gives this one."}]},"bumper_length":{"label":"Length of the polymer bumper, from the end cap to its front face","kind":"length","measurements":[{"id":"standard","value":0.979,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.bumper_length}","via":"harvest"},"note":"The standard unit's figure: the bumper and the end cap are the standard GEN 2's, and no photo of the H2 gives this one."}]},"bumper_front_d":{"label":"The bumper's diameter at its front face","kind":"length","measurements":[{"id":"standard","value":0.918,"unit":"in","pm":0.016,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.bumper_front_d}","via":"harvest"},"note":"The standard unit's figure: the bumper and the end cap are the standard GEN 2's, and no photo of the H2 gives this one."}]},"bumper_rear_d":{"label":"The bumper's diameter at its rear (it tapers toward the front)","kind":"length","measurements":[{"id":"standard","value":0.993,"unit":"in","pm":0.016,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.bumper_rear_d}","via":"harvest"},"note":"The standard unit's figure: the bumper and the end cap are the standard GEN 2's, and no photo of the H2 gives this one."}]},"bumper_front_round":{"label":"The round on the bumper's front edge","kind":"length","measurements":[{"id":"standard","value":0.06,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.bumper_front_round}","via":"harvest"},"note":"The standard unit's figure: the bumper and the end cap are the standard GEN 2's, and no photo of the H2 gives this one."}]},"cap_d":{"label":"Diameter of the black end cap at the rear","kind":"length","measurements":[{"id":"standard","value":0.996,"unit":"in","pm":0.016,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.cap_d}","via":"harvest"},"note":"The standard unit's figure: the bumper and the end cap are the standard GEN 2's, and no photo of the H2 gives this one."}]},"cap_length":{"label":"Length of the end cap","kind":"length","measurements":[{"id":"standard","value":0.116,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.cap_length}","via":"harvest"},"note":"The standard unit's figure: the bumper and the end cap are the standard GEN 2's, and no photo of the H2 gives this one."}]},"cap_round":{"label":"The round on the end cap's rear edge","kind":"length","measurements":[{"id":"standard","value":0.035,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.cap_round}","via":"harvest"},"note":"The standard unit's figure: the bumper and the end cap are the standard GEN 2's, and no photo of the H2 gives this one."}]},"cap_spigot_d":{"label":"The end cap's spigot inside the bumper's rear half (its front, which carries the spring's rear end)","kind":"length","measurements":[{"id":"standard","value":0.7,"unit":"in","pm":0.08,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.cap_spigot_d}","via":"harvest"},"note":"The standard unit's figure: the bumper and the end cap are the standard GEN 2's, and no photo of the H2 gives this one."}]},"pocket_depth":{"label":"Depth of the end cap's pocket to the screw's head","kind":"length","measurements":[{"id":"standard","value":0.05,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.pocket_depth}","via":"harvest"},"note":"The standard unit's figure: the bumper and the end cap are the standard GEN 2's, and no photo of the H2 gives this one."}]},"spring_od":{"label":"The spring's outside diameter","kind":"length","measurements":[{"id":"standard","value":0.51,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.spring_od}","via":"harvest"},"note":"The standard's spring's size: the H2's spring (JP's 15-100, the kit sheet) shows square to its side in no photo on file, and in the H2's three-quarter photo (708eab533a4c, levelled) its outside reads 0.49 in against the weights beside it, 4% under the standard's, which the photo's perspective (the weights 6% larger at their front end than at their rear) makes no more than a check."}]},"wire_d":{"label":"The spring's wire","kind":"length","measurements":[{"id":"standard","value":0.047,"unit":"in","pm":0.004,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.wire_d}","via":"harvest"},"note":"The standard's spring's size: the H2's spring (JP's 15-100, the kit sheet) shows square to its side in no photo on file, and in the H2's three-quarter photo (708eab533a4c, levelled) its outside reads 0.49 in against the weights beside it, 4% under the standard's, which the photo's perspective (the weights 6% larger at their front end than at their rear) makes no more than a check."}]}}},{"subject":"jp-silent-captured-spring-gen2-h3","title":"JP Enterprises Silent Captured Spring AR-15 Heavy H3 GEN 2","dimensions":{"weight":{"label":"Weight (the whole unit)","kind":"mass","measurements":[{"id":"jp","value":7.7,"unit":"oz","pm":0.05,"stated":"Weight: 7.7 oz.","source":{"type":"spec","publisher":"manufacturer","name":"JP Enterprises, GEN 2 Silent Captured Spring System for AR-15 type rifle with H3 extra heavy buffer #JPSCS2-15H3 (the maker's store page)","url":"https://jprifles.com/buy_test.php?item=JPSCS2-15H3","retrieved":"2026-10-18","via":"harvest"}}]},"buffering_mass":{"label":"The buffer's mass: the slider with its weights, which the carrier drives (what a buffer's class is)","kind":"mass","measurements":[{"id":"jp","value":5.6,"unit":"oz","pm":0.05,"stated":"Buffering/Reciprocating Mass: 5.6 oz. (Ideal for replacing a standard buffer of the same weight)","source":{"type":"spec","publisher":"manufacturer","name":"JP Enterprises, GEN 2 Silent Captured Spring System for AR-15 type rifle with H3 extra heavy buffer #JPSCS2-15H3 (the maker's store page)","url":"https://jprifles.com/buy_test.php?item=JPSCS2-15H3","retrieved":"2026-10-18","via":"harvest"},"note":"JP's FAQ table: \"3 Tungsten (H3) 5.6 oz. JPSCS2-15H3\". Over the standard's 2.9 oz it is 0.90 oz a tungsten weight; the unit's weight over the standard's, 7.7 against 5.3, is 0.80, as the H2's is."}]},"tungsten_count":{"label":"Of the three weights, how many are tungsten","kind":"count","measurements":[{"id":"jp","value":3,"unit":"count","stated":"3 Tungsten (H3) 5.6 oz. JPSCS2-15H3","source":{"type":"spec","publisher":"manufacturer","name":"JP Enterprises, Buffer Springs and Silent Captured Springs (FAQ: SCS Mass Configuration)","url":"https://jprifles.com/1.4.7.2_os.php?menu_select=scs_guide","retrieved":"2026-10-18","via":"harvest"}}]},"flange_d":{"label":"Diameter of the slider's front flange (black), the face the carrier bears on","kind":"length","measurements":[{"id":"standard","value":0.993,"unit":"in","pm":0.016,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.flange_d}","via":"harvest"},"note":"The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H3 gives this one."}]},"flange_length":{"label":"Length of the front flange","kind":"length","measurements":[{"id":"standard","value":0.209,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.flange_length}","via":"harvest"},"note":"The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H3 gives this one."}]},"flange_round":{"label":"The round on the flange's front edge","kind":"length","measurements":[{"id":"standard","value":0.045,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.flange_round}","via":"harvest"},"note":"The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H3 gives this one."}]},"oring_gap":{"label":"Width of each O-ring's band between the flange and a weight and between two weights","kind":"length","measurements":[{"id":"standard","value":0.072,"unit":"in","pm":0.016,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.oring_gap}","via":"harvest"},"note":"The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H3 gives this one."}]},"oring_d":{"label":"Diameter of the O-rings as they show between the weights","kind":"length","measurements":[{"id":"standard","value":0.942,"unit":"in","pm":0.016,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.oring_d}","via":"harvest"},"note":"The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H3 gives this one."}]},"od":{"label":"Diameter of the three weights (the buffer's widest steel)","kind":"length","measurements":[{"id":"standard","value":0.966,"unit":"in","pm":0.016,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.od}","via":"harvest"},"note":"The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H3 gives this one."}]},"mass_length":{"label":"Length of one weight","kind":"length","measurements":[{"id":"standard","value":0.572,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.mass_length}","via":"harvest"},"note":"The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H3 gives this one."}]},"mass_chamfer":{"label":"The break on each weight's edges","kind":"length","measurements":[{"id":"standard","value":0.014,"unit":"in","pm":0.007,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.mass_chamfer}","via":"harvest"},"note":"The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H3 gives this one."}]},"mass_count":{"label":"Weights on the slider","kind":"count","measurements":[{"id":"standard","value":3,"unit":"count","source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.mass_count}","via":"harvest"},"note":"The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H3 gives this one."}]},"snap_ring_length":{"label":"Width of the snap ring's band behind the rearmost weight","kind":"length","measurements":[{"id":"standard","value":0.062,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.snap_ring_length}","via":"harvest"},"note":"The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H3 gives this one."}]},"snap_ring_d":{"label":"Diameter of the snap ring as it shows","kind":"length","measurements":[{"id":"standard","value":0.897,"unit":"in","pm":0.025,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.snap_ring_d}","via":"harvest"},"note":"The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H3 gives this one."}]},"collar_d":{"label":"Diameter of the slider's black rear collar, which the spring bears on","kind":"length","measurements":[{"id":"standard","value":0.805,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.collar_d}","via":"harvest"},"note":"The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H3 gives this one."}]},"collar_length":{"label":"Length of the rear collar","kind":"length","measurements":[{"id":"standard","value":0.164,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.collar_length}","via":"harvest"},"note":"The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H3 gives this one."}]},"mass_bore_d":{"label":"Bore of the weights (the slider's tube under them)","kind":"length","measurements":[{"id":"standard","value":0.805,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.mass_bore_d}","via":"harvest"},"note":"The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H3 gives this one."}]},"front_bore_depth":{"label":"Depth of that bore to the screw's head (unit out of the rifle)","kind":"length","measurements":[{"id":"standard","value":0.25,"unit":"in","pm":0.1,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.front_bore_depth}","via":"harvest"},"note":"The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H3 gives this one."}]},"inner_flange":{"label":"The slider's inner flange: how thick it is, behind the front bore (the front screw's head bears on it from ahead, the spring from behind)","kind":"length","measurements":[{"id":"standard","value":0.1,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.inner_flange}","via":"harvest"},"note":"The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H3 gives this one."}]},"slider_bore_d":{"label":"Bore through the slider from its rear to its inner flange, which the spring's front end goes into (and the bumper's, which its rear end goes into)","kind":"length","measurements":[{"id":"standard","value":0.53,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.slider_bore_d}","via":"harvest"},"note":"The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H3 gives this one."}]},"length":{"label":"Length out of the rifle (the slider's front face to the end cap's rear face)","kind":"length","measurements":[{"id":"standard","value":7.249,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.length}","via":"harvest"},"note":"The standard unit's figure: the unit's length, the guide rod and its screws are the standard GEN 2's, and no photo of the H3 gives this one."}]},"installed_length":{"label":"The unit's length in the rifle, bolt forward (the slider's front face on the carrier to the extension's rear wall)","kind":"length","measurements":[{"id":"standard","value":7.226,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.installed_length}","via":"harvest"},"note":"The standard unit's figure: the unit's length, the guide rod and its screws are the standard GEN 2's, and no photo of the H3 gives this one."}]},"protrusion":{"label":"How far the unit stands out of the extension past the lower's face with the receivers open","kind":"length","measurements":[{"id":"standard","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.protrusion}","via":"harvest"},"note":"The standard unit's figure: the unit's length, the guide rod and its screws are the standard GEN 2's, and no photo of the H3 gives this one."}]},"rod_d":{"label":"Diameter of the guide rod (aluminium)","kind":"length","measurements":[{"id":"standard","value":0.377,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.rod_d}","via":"harvest"},"note":"The standard unit's figure: the unit's length, the guide rod and its screws are the standard GEN 2's, and no photo of the H3 gives this one."}]},"carrier_channel_min":{"label":"The narrowest rear channel of a bolt carrier the guide rod passes into while cycling","kind":"length","measurements":[{"id":"standard","value":0.53,"unit":"in","pm":0.0005,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.carrier_channel_min}","via":"harvest"},"note":"The standard unit's figure: the unit's length, the guide rod and its screws are the standard GEN 2's, and no photo of the H3 gives this one."}]},"hex_socket":{"label":"The screws' hex socket, across its flats","kind":"length","measurements":[{"id":"standard","value":0.125,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.hex_socket}","via":"harvest"},"note":"The standard unit's figure: the unit's length, the guide rod and its screws are the standard GEN 2's, and no photo of the H3 gives this one."}]},"bumper_length":{"label":"Length of the polymer bumper, from the end cap to its front face","kind":"length","measurements":[{"id":"standard","value":0.979,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.bumper_length}","via":"harvest"},"note":"The standard unit's figure: the bumper and the end cap are the standard GEN 2's, and no photo of the H3 gives this one."}]},"bumper_front_d":{"label":"The bumper's diameter at its front face","kind":"length","measurements":[{"id":"standard","value":0.918,"unit":"in","pm":0.016,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.bumper_front_d}","via":"harvest"},"note":"The standard unit's figure: the bumper and the end cap are the standard GEN 2's, and no photo of the H3 gives this one."}]},"bumper_rear_d":{"label":"The bumper's diameter at its rear (it tapers toward the front)","kind":"length","measurements":[{"id":"standard","value":0.993,"unit":"in","pm":0.016,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.bumper_rear_d}","via":"harvest"},"note":"The standard unit's figure: the bumper and the end cap are the standard GEN 2's, and no photo of the H3 gives this one."}]},"bumper_front_round":{"label":"The round on the bumper's front edge","kind":"length","measurements":[{"id":"standard","value":0.06,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.bumper_front_round}","via":"harvest"},"note":"The standard unit's figure: the bumper and the end cap are the standard GEN 2's, and no photo of the H3 gives this one."}]},"cap_d":{"label":"Diameter of the black end cap at the rear","kind":"length","measurements":[{"id":"standard","value":0.996,"unit":"in","pm":0.016,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.cap_d}","via":"harvest"},"note":"The standard unit's figure: the bumper and the end cap are the standard GEN 2's, and no photo of the H3 gives this one."}]},"cap_length":{"label":"Length of the end cap","kind":"length","measurements":[{"id":"standard","value":0.116,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.cap_length}","via":"harvest"},"note":"The standard unit's figure: the bumper and the end cap are the standard GEN 2's, and no photo of the H3 gives this one."}]},"cap_round":{"label":"The round on the end cap's rear edge","kind":"length","measurements":[{"id":"standard","value":0.035,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.cap_round}","via":"harvest"},"note":"The standard unit's figure: the bumper and the end cap are the standard GEN 2's, and no photo of the H3 gives this one."}]},"cap_spigot_d":{"label":"The end cap's spigot inside the bumper's rear half (its front, which carries the spring's rear end)","kind":"length","measurements":[{"id":"standard","value":0.7,"unit":"in","pm":0.08,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.cap_spigot_d}","via":"harvest"},"note":"The standard unit's figure: the bumper and the end cap are the standard GEN 2's, and no photo of the H3 gives this one."}]},"pocket_depth":{"label":"Depth of the end cap's pocket to the screw's head","kind":"length","measurements":[{"id":"standard","value":0.05,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.pocket_depth}","via":"harvest"},"note":"The standard unit's figure: the bumper and the end cap are the standard GEN 2's, and no photo of the H3 gives this one."}]},"front_bore_d":{"label":"Diameter of the bore in the slider's front face (the guide rod's screw is at its bottom)","kind":"length","measurements":[{"id":"standard","value":0.546,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.front_bore_d}","via":"harvest"},"note":"The standard unit's figure (read there on the H2's photos of the same slider and end cap): no photo of the H3 gives it."}]},"cap_pocket_d":{"label":"The pocket in the end cap's rear face that the rear screw's head sits in","kind":"length","measurements":[{"id":"standard","value":0.42,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.cap_pocket_d}","via":"harvest"},"note":"The standard unit's figure (read there on the H2's photos of the same slider and end cap): no photo of the H3 gives it."}]},"screw_head_d":{"label":"The rear screw's head","kind":"length","measurements":[{"id":"standard","value":0.36,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2.screw_head_d}","via":"harvest"},"note":"The standard unit's figure (read there on the H2's photos of the same slider and end cap): no photo of the H3 gives it."}]},"spring_od":{"label":"The spring's outside diameter","kind":"length","measurements":[{"id":"h2","value":0.51,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2-h2.spring_od}","via":"harvest"},"note":"The H2's spring: JP names no spring for the H3, and its only picture of the H3 (references/jp-silent-captured-spring-gen2-h3 5251098b70ce) is its picture of the H2 (c5a3ef37c597) with the steel weight darkened: the same silhouette to the pixel, the H2's spring in it. JP's use table gives the two one row."}]},"wire_d":{"label":"The spring's wire","kind":"length","measurements":[{"id":"h2","value":0.047,"unit":"in","pm":0.004,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2-h2.wire_d}","via":"harvest"},"note":"The H2's spring: JP names no spring for the H3, and its only picture of the H3 (references/jp-silent-captured-spring-gen2-h3 5251098b70ce) is its picture of the H2 (c5a3ef37c597) with the steel weight darkened: the same silhouette to the pixel, the H2's spring in it. JP's use table gives the two one row."}]},"coils":{"label":"The spring's turns, end to end","kind":"count","measurements":[{"id":"h2","value":25,"unit":"count","pm":1,"source":{"type":"derived","expr":"{jp-silent-captured-spring-gen2-h2.coils}","via":"harvest"},"note":"The H2's spring: JP names no spring for the H3, and its only picture of the H3 (references/jp-silent-captured-spring-gen2-h3 5251098b70ce) is its picture of the H2 (c5a3ef37c597) with the steel weight darkened: the same silhouette to the pixel, the H2's spring in it. JP's use table gives the two one row."}]}}},{"subject":"jp-silent-captured-spring-gen2","title":"JP Enterprises Silent Captured Spring AR-15 Standard GEN 2","dimensions":{"weight":{"label":"Weight (the whole unit)","kind":"mass","measurements":[{"id":"jp","value":5.3,"unit":"oz","pm":0.05,"stated":"Weight: 5.3 oz.","source":{"type":"spec","publisher":"manufacturer","name":"JP Enterprises, GEN 2 Silent Captured Spring for AR-15 type rifle #JPSCS2-15 (the maker's store page)","url":"https://jprifles.com/buy_test.php?item=JPSCS2-15","retrieved":"2026-10-18","via":"harvest"}},{"id":"silencershop","value":5.3,"unit":"oz","pm":0.05,"stated":"Technical Specifications: Weight: 5.3 oz","source":{"type":"spec","publisher":"retailer","name":"Silencer Shop, JP GEN 2 Silent Captured Spring - AR15","url":"https://www.silencershop.com/jp-gen-2-silent-captured-spring-ar15.html","retrieved":"2026-10-18","via":"harvest"}},{"id":"primary-arms","value":6.2,"unit":"oz","pm":0.05,"stated":"Brand JP Enterprises Buffer Standard Carbine Platform AR-15 Weight 6.2 oz.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, JP Enterprises SCS Silent Capture Spring Gen 2 AR-15 Buffer - Carbine/Rifle","url":"https://www.primaryarms.com/jp-silent-captured-spring-for-ar15-gen-2","retrieved":"2026-10-18","via":"harvest"},"note":"What was weighed isn't said: the box holds the rifle-length spacer and the shim as well (JP's sheet: \"PARTS INCLUDED • Silent Captured Spring • Rifle-length spacer • Spacer shim\"). AR15Discounts' shop field \"Weight 6.24 oz\" is the same figure."}],"adopt":{"from":"jp","reason":"The maker's figure for the unit, and a second seller's the same. Primary Arms' 6.2 oz is likely the unit with its spacer (Wing Tactical's spacer is 2.7 in of polymer tube), and stays here beside it."}},"buffering_mass":{"label":"The buffer's mass: the slider with its three weights, which the carrier drives (what a buffer's class is)","kind":"mass","measurements":[{"id":"jp","value":2.9,"unit":"oz","pm":0.05,"stated":"Buffering/Reciprocating Mass: 2.9 oz. (Ideal for replacing a standard buffer of the same weight)","source":{"type":"spec","publisher":"manufacturer","name":"JP Enterprises, GEN 2 Silent Captured Spring for AR-15 type rifle #JPSCS2-15 (the maker's store page)","url":"https://jprifles.com/buy_test.php?item=JPSCS2-15","retrieved":"2026-10-18","via":"harvest"},"note":"JP's FAQ has the table it comes from: \"SCS Mass Configuration Buffer Mass AR-15 AR-10 3 Steel 2.9 oz. JPSCS2-15 JPSCS2-10 1 Tungsten | 2 Steel (H) 4.0 oz. ... 2 Tungsten | 1 Steel (H2) 4.8 oz. JPSCS2-15H2 ... 3 Tungsten (H3) 5.6 oz. JPSCS2-15H3\" (https://jprifles.com/1.4.7.2_os.php?menu_select=scs_guide). The instruction sheet: \"one with all steel masses that equates to a standard carbine buffer\"."}]},"protrusion":{"label":"How far the unit stands out of the extension past the lower's face with the receivers open","kind":"length","measurements":[{"id":"sheet","value":0.03,"unit":"in","pm":0.015,"stated":"The SCS should protrude about .030”, which is the width of the included spacer shim.","source":{"type":"spec","publisher":"manufacturer","name":"JP Enterprises, GEN 2 Silent Captured Spring instruction sheet (JPSCS2-15, JPSCS2-10), Rev. 05.24, page 2, FITMENT","url":"https://jprifles.com/document_pdfs/JPSCS2_912.pdf","retrieved":"2026-10-18","via":"harvest"},"note":"The ± reaches the low end of the washer sheet's window (.015 to .060) printed on the same page."}],"note":"JP's FAQ: \"With the action open, the JPSCS should protrude from the buffer tube very slightly, 1/16\" or less. If it's below flush then it won't reliably push the bolt carrier all the way to closed.\" Taken to be past the lower's face (the buffer tower's front face, std.ar15.buffer_tower_front_x), where the shim washer's sheet measures it (\"check for proper protrusion from the receiver face. If it is between .015\" and .060\" then the SCS2-WASHER need not be used.\"): measured from the extension's own front end, 0.04 in further back, the unit as photographed would not reach the carrier at all."},"installed_length":{"label":"The unit's length in the rifle, bolt forward (the slider's front face on the carrier to the extension's rear wall)","kind":"length","measurements":[{"id":"room","value":7.226,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{std.carbine_buffer.head_thickness} + {bcm-carbine-action-spring.installed_length}","via":"harvest"}}],"note":"The room a carbine buffer and its spring have: a buffer's front face rests at the upper receiver's rear face, and the spring's room runs from the head's rear face to the tube's rear wall (bcm-carbine-action-spring.installed_length). What the model is drawn at."},"length":{"label":"Length out of the rifle (the slider's front face to the end cap's rear face)","kind":"length","measurements":[{"id":"protrusion","value":7.249,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.installed_length} + {std.ar15.buffer_tower_front_x} + {.protrusion} - {std.ar15.upper_rear_face_x}","via":"harvest"},"note":"From the tube's rear wall to the lower's face, and JP's .030 past it: the length the unit stands at out of the rifle, the slider on its stop. Closing the receivers pushes the slider back by what is left, 0.023 in, which is the \"good tension against the bolt carrier\" JP asks for."},{"id":"wing","value":7,"unit":"in","pm":0.5,"stated":"Length: Silent Captured Spring System: 7\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, JP Enterprises Silent Captured Spring AR-15 Buffer System (Gen 2) (one page for the standard and the H2)","url":"https://www.wingtactical.com/firearm-parts/ar-15/buffer-buffer-tubes/jp-enterprises-silent-captured-spring-ar-15-buffer-system-gen-2/","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"protrusion","reason":"The maker's own fitting figure over the standard extension's room; one seller's 7 in, to the inch, holds it. AR15Discounts' shop field \"Dimensions 3.8 × 0.8 × 0.8 in\" is no length of the unit (its slider alone is 2.4 in and its spring longer)."}},"rifle_spacer_length":{"label":"The rifle-length spacer's length (in the box; not drawn: it goes behind the unit in a rifle-length extension)","kind":"length","measurements":[{"id":"wing","value":2.7,"unit":"in","pm":0.05,"stated":"Spacer: 2.7\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, JP Enterprises Silent Captured Spring AR-15 Buffer System (Gen 2)","url":"https://www.wingtactical.com/firearm-parts/ar-15/buffer-buffer-tubes/jp-enterprises-silent-captured-spring-ar-15-buffer-system-gen-2/","retrieved":"2026-10-18","via":"harvest"}}]},"carrier_channel_min":{"label":"The narrowest rear channel of a bolt carrier the guide rod passes into while cycling","kind":"length","measurements":[{"id":"jp","value":0.53,"unit":"in","pm":0.0005,"stated":"This is because the guide rod of the SCS needs to pass into the carrier during cycling, and some alternate designs don't have adequate space. Mil-spec bore for the rear channel of a bolt carrier is .625, but the SCS will work with carriers down to .530\".","source":{"type":"spec","publisher":"manufacturer","name":"JP Enterprises, Buffer Springs and Silent Captured Springs (FAQ)","url":"https://jprifles.com/1.4.7.2_os.php?menu_select=scs_guide","retrieved":"2026-10-18","via":"harvest"}}]},"od":{"label":"Diameter of the three weights (the buffer's widest steel)","kind":"length","measurements":[{"id":"photo","value":0.966,"unit":"in","pm":0.016,"source":{"type":"photo","photo":"references/jp-silent-captured-spring-gen2 3431b2d79bca (MidwayUSA 767861, the standard unit square to its side on white, 2200 x 1650)","scaleRef":"the unit's length out of the rifle (.length, 7.249 in) over its 2117 px: 292.0 px/in","method":"the weights' silhouette, 282 px from top to bottom along all three (threshold 235 of 255; 281 to 283 px)","via":"harvest"},"note":"Under a standard carbine buffer's head (0.98) and the extension's 1.000 bore."}]},"flange_d":{"label":"Diameter of the slider's front flange (black), the face the carrier bears on","kind":"length","measurements":[{"id":"photo","value":0.993,"unit":"in","pm":0.016,"source":{"type":"photo","photo":"references/jp-silent-captured-spring-gen2 3431b2d79bca","scaleRef":"292.0 px/in (.length)","method":"the flange's silhouette, 290 px, px 2106 to 2148","via":"harvest"}},{"id":"pa","value":0.978,"unit":"in","pm":0.016,"source":{"type":"photo","photo":"references/jp-silent-captured-spring-gen2 0b290578345a (Primary Arms' JPSCS2-15_01 on its page for the standard, the same picture at Dirty Bird and AR15Discounts: the unit square to its side on white, 2000 x 1333, front at the left)","scaleRef":"the unit's length out of the rifle (.length, 7.249 in) over its 1683 px (px 158 to 1841): 232.2 px/in","method":"the flange's silhouette, 227 px, px 172 to 205","via":"harvest"},"note":"Inside the ± of the reading above; the black collar and flange read 2% under MidwayUSA's throughout, which the two lenses' distances would give."}],"adopt":{"from":"photo","reason":"MidwayUSA's photo is the one every size of the slider is read on; Primary Arms' reads its black pieces 1.5 to 2% smaller throughout, one scale against another. Both are under the extension's 1.000 bore."}},"flange_length":{"label":"Length of the front flange","kind":"length","measurements":[{"id":"photo","value":0.209,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/jp-silent-captured-spring-gen2 3431b2d79bca","scaleRef":"292.0 px/in (.length)","method":"from the front end (px 2164) to the flange's rear edge where the O-ring's dark band begins (px 2103), 61 px","via":"harvest"}}]},"flange_round":{"label":"The round on the flange's front edge","kind":"length","measurements":[{"id":"photo","value":0.045,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/jp-silent-captured-spring-gen2 3431b2d79bca","scaleRef":"292.0 px/in (.length)","method":"the silhouette falls from the flange's full height at px 2151 to the end at px 2164, 13 px; the H2's front view (708eab533a4c) shows the edge broken all round","via":"harvest"}}]},"oring_gap":{"label":"Width of each O-ring's band between the flange and a weight and between two weights","kind":"length","measurements":[{"id":"photo","value":0.072,"unit":"in","pm":0.016,"source":{"type":"photo","photo":"references/jp-silent-captured-spring-gen2 3431b2d79bca","scaleRef":"292.0 px/in (.length)","method":"the three bands from a weight's edge to the next: 15 px behind the flange (px 2088 to 2103) and 24 px between the weights (px 1899 to 1923, 1707 to 1731), 18 px of each of those dark; their mean, 21 px. The slider's pieces as drawn come to its 691 px with it","via":"harvest"},"note":"JP's weights sheet: \"One O-ring should be positioned on every side of the weights except in the space between the weight and the snap ring.\" (https://jprifles.com/document_pdfs/JPSCS2HMSM_948.pdf)"}]},"oring_d":{"label":"Diameter of the O-rings as they show between the weights","kind":"length","measurements":[{"id":"photo","value":0.942,"unit":"in","pm":0.016,"source":{"type":"photo","photo":"references/jp-silent-captured-spring-gen2 3431b2d79bca","scaleRef":"292.0 px/in (.length)","method":"the silhouette at the dark bands, 274 to 277 px","via":"harvest"}}]},"mass_length":{"label":"Length of one weight","kind":"length","measurements":[{"id":"photo","value":0.572,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/jp-silent-captured-spring-gen2 3431b2d79bca","scaleRef":"292.0 px/in (.length)","method":"edge to edge of each weight: 165, 168 and 168 px (px 1923 to 2088, 1731 to 1899, 1539 to 1707)","via":"harvest"}}]},"mass_count":{"label":"Weights on the slider","kind":"count","measurements":[{"id":"jp","value":3,"unit":"count","stated":"3 Steel 2.9 oz. JPSCS2-15","source":{"type":"spec","publisher":"manufacturer","name":"JP Enterprises, Buffer Springs and Silent Captured Springs (FAQ: SCS Mass Configuration)","url":"https://jprifles.com/1.4.7.2_os.php?menu_select=scs_guide","retrieved":"2026-10-18","via":"harvest"}}]},"tungsten_count":{"label":"Of the three weights, how many are tungsten","kind":"count","measurements":[{"id":"jp","value":0,"unit":"count","stated":"3 Steel 2.9 oz. JPSCS2-15","source":{"type":"spec","publisher":"manufacturer","name":"JP Enterprises, Buffer Springs and Silent Captured Springs (FAQ: SCS Mass Configuration)","url":"https://jprifles.com/1.4.7.2_os.php?menu_select=scs_guide","retrieved":"2026-10-18","via":"harvest"}}]},"snap_ring_length":{"label":"Width of the snap ring's band behind the rearmost weight","kind":"length","measurements":[{"id":"photo","value":0.062,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/jp-silent-captured-spring-gen2 3431b2d79bca","scaleRef":"292.0 px/in (.length)","method":"px 1521 to 1539, 18 px, between the black collar and the rearmost weight","via":"harvest"},"note":"JP's weights sheet: \"Remove the snap ring from the SCS mass assembly by using the tip of a small screwdriver to pry up the end of the ring and slide it off the back side of slider.\""}]},"snap_ring_d":{"label":"Diameter of the snap ring as it shows","kind":"length","measurements":[{"id":"photo","value":0.897,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/jp-silent-captured-spring-gen2 3431b2d79bca","scaleRef":"292.0 px/in (.length)","method":"the silhouette there, 255 to 268 px","via":"harvest"}}]},"collar_d":{"label":"Diameter of the slider's black rear collar, which the spring bears on","kind":"length","measurements":[{"id":"photo","value":0.805,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/jp-silent-captured-spring-gen2 3431b2d79bca","scaleRef":"292.0 px/in (.length)","method":"the collar's silhouette, 235 px, px 1476 to 1521","via":"harvest"}},{"id":"pa","value":0.788,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/jp-silent-captured-spring-gen2 0b290578345a (Primary Arms' JPSCS2-15_01 on its page for the standard, the same picture at Dirty Bird and AR15Discounts: the unit square to its side on white, 2000 x 1333, front at the left)","scaleRef":"232.2 px/in (.length over 1683 px)","method":"the collar's silhouette, 183 px, px 670 to 703","via":"harvest"}}],"adopt":{"from":"photo","reason":"MidwayUSA's photo is the one every size of the slider is read on, so the slider's proportions are one photo's; Primary Arms' reads the flange and the collar alike 1.5 to 2% smaller, one scale's difference between the two pictures, not the collar's own."}},"collar_length":{"label":"Length of the rear collar","kind":"length","measurements":[{"id":"photo","value":0.164,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/jp-silent-captured-spring-gen2 3431b2d79bca","scaleRef":"292.0 px/in (.length)","method":"px 1473 to 1521, 48 px","via":"harvest"}}]},"front_bore_d":{"label":"Diameter of the bore in the slider's front face (the guide rod's screw is at its bottom)","kind":"length","measurements":[{"id":"photo","value":0.546,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/jp-silent-captured-spring-gen2 708eab533a4c (Primary Arms' JPSCS2-15H2_01, the H2 from ahead of its front face, 2200 x 1467: the same slider and flange as the standard's, its weights tungsten)","scaleRef":"the flange's own diameter (.flange_d) across the face's ellipse","method":"the bore's long axis over the flange's along the same line, 0.55: a ratio along an ellipse's long axis is true whatever the lean","via":"harvest"},"note":"Wider than the carrier's narrowest channel JP names (.530): the rod's head, not the bore, goes into the carrier."}]},"front_bore_depth":{"label":"Depth of that bore to the screw's head (unit out of the rifle)","kind":"length","measurements":[{"id":"assumed","value":0.25,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows the bore in section. Wing Tactical's view of a front face (26c0d1ee43a2) has the screw's head well down in it, under its own diameter's depth.","via":"harvest"}}]},"mass_bore_d":{"label":"Bore of the weights (the slider's tube under them)","kind":"length","measurements":[{"id":"collar","value":0.805,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{.collar_d}","via":"harvest"},"note":"An assumption for the drawing, not a reading: the weights' insides never show. Taken to be the slider's tube, whose rear end is the black collar seen behind the snap ring (JP's weights sheet: the weights come off \"the back side of slider\" once the snap ring is off). app/tests/jp-silent-captured-spring-gen2.test.ts holds the slider so drawn to JP's 2.9 oz."}]},"slider_bore_d":{"label":"Bore through the slider from its rear to its inner flange, which the spring's front end goes into (and the bumper's, which its rear end goes into)","kind":"length","measurements":[{"id":"assumed","value":0.53,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the bore never shows but at its mouth, behind the spring's coils. The spring's outside (.spring_od) and a clearance, by the patent's words.","via":"harvest"}}],"note":"The maker's patent: \"The buffer 22 has a slider 28 with a central bore 134 that defines an interior surface 40. The central bore is sufficiently large to receive the front 54 of the bolt return spring 52. A flange 36 protrudes inwardly from the interior surface to define an aperture 94 and to limit forward movement of the bolt return spring.\" And of the bumper: \"The resilient portion has a central bore 62 that defines an interior surface 68. The central bore is sufficiently large to permit passage of the rear 16 of the guide rod 12 and to receive the rear 56 of the bolt return spring 52.\""},"inner_flange":{"label":"The slider's inner flange: how thick it is, behind the front bore (the front screw's head bears on it from ahead, the spring from behind)","kind":"length","measurements":[{"id":"assumed","value":0.1,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view shows the slider in section; the patent's FIG. 1B draws the flange about a twentieth of the slider's length, a drawing of the first generation and not to a stated scale.","via":"harvest"}}],"note":"The maker's patent: \"Forward motion of the buffer 22 is constrained by the head 48 of a front screw 46. ... The head is sized with a diameter such that the head extends outwardly beyond the guide rod and is too large to pass through the aperture 94 defined by the flange 36 in the slider 28.\" \"The front 54 of the spring abuts the flange 36 of the slider\"."},"cap_spigot_d":{"label":"The end cap's spigot inside the bumper's rear half (its front, which carries the spring's rear end)","kind":"length","measurements":[{"id":"assumed","value":0.7,"unit":"in","pm":0.08,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the spigot never shows. Between the spring's bore (.slider_bore_d) and the bumper's outside, as the patent's FIG. 1B draws it.","via":"harvest"}}],"note":"The maker's patent: \"The interior surface also defines a ledge 64 at a point approximately midway between the front and the rear. The front 78 of the end cap 76 is inserted into the rear 72 of the bore 62 of the resilient portion 60 and abuts the ledge 64. ... the rear 56 of the spring abuts the rear of the central bore 84 in the end cap.\" In the patent's embodiment \"the resilient portion is made of urethane and the end cap is made of steel\"."},"mass_chamfer":{"label":"The break on each weight's edges","kind":"length","measurements":[{"id":"photo","value":0.014,"unit":"in","pm":0.007,"source":{"type":"photo","photo":"references/jp-silent-captured-spring-gen2 3431b2d79bca","scaleRef":"292.0 px/in (.length)","method":"the silhouette drops from 281 to 273 px over the last 3 to 6 px of each weight: 4 px a side","via":"harvest"}}]},"rod_d":{"label":"Diameter of the guide rod (aluminium)","kind":"length","measurements":[{"id":"photo","value":0.377,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/jp-silent-captured-spring-gen2 3431b2d79bca","scaleRef":"292.0 px/in (.length)","method":"the rod's two edges between the coils along the whole spring: the commonest top edge row 769 and bottom 878, 110 px","via":"harvest"},"note":"Under JP's .530 carrier channel, which it has to enter."}],"note":"Wing Tactical: \"Material: Guide Rod: Aluminum Buffer Weights: Tungsten and Steel\"."},"spring_od":{"label":"The spring's outside diameter","kind":"length","measurements":[{"id":"photo","value":0.51,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/jp-silent-captured-spring-gen2 3431b2d79bca","scaleRef":"292.0 px/in (.length)","method":"a coil's top crest to its bottom crest, 146 px; the envelope of all the coils, 153 px (0.524) with their lean","via":"harvest"}}]},"wire_d":{"label":"The spring's wire","kind":"length","measurements":[{"id":"photo","value":0.047,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/jp-silent-captured-spring-gen2 3431b2d79bca","scaleRef":"292.0 px/in (.length)","method":"a coil's width across its wire where it crosses the rod, 13 to 14 px, on crops at twice the size","via":"harvest"}}]},"coils":{"label":"The spring's turns, end to end","kind":"count","measurements":[{"id":"photo","value":28.5,"unit":"count","pm":0.5,"source":{"type":"photo","photo":"references/jp-silent-captured-spring-gen2 3431b2d79bca","scaleRef":"none: a count","method":"the crests along the spring's top edge, counted on two crops at twice the size (px 360 to 940 and 900 to 1500, overlapping at one crest): 29 crests 38.8 px apart from the coil on the bumper's face to the coil on the collar, and the ends between","via":"harvest"},"note":"JP: \"The AR-15 models comes with a 15-85 spring\"; the kit's sheet has it \"Black - Uncolored\" at its ends. Its free length isn't on a page. The count is of what shows between the collar and the bumper: the spring runs on inside both (the patent), drawn at the same pitch."},{"id":"pa","value":30.5,"unit":"count","pm":0.5,"source":{"type":"photo","photo":"references/jp-silent-captured-spring-gen2 0b290578345a (Primary Arms' JPSCS2-15_01 on its page for the standard, the same picture at Dirty Bird and AR15Discounts: the unit square to its side on white, 2000 x 1333, front at the left)","scaleRef":"none: a count","method":"the crests along the spring's top edge on two crops at 2.2 times the size (px 690 to 1160 and 1140 to 1610, overlapping at one crest): 31 crests 28.6 px apart, from the coil on the collar (px 715) to the coil on the bumper's face (px 1574)","via":"harvest"},"note":"The spring is black for two thirds of its length from the bumper and bare toward the collar: JP's kit sheet codes the standard's spring so, \"JPSCS-15-85* Black - Uncolored\" with \"* JPSCS2-15\" (https://jprifles.com/document_pdfs/JPSCS2%20Kit_911.pdf)."}],"adopt":{"from":"pa","reason":"Two runs of the product under one number, two coils apart. Primary Arms' spring carries the colour code JP gives the standard's 15-85 spring; MidwayUSA's is bare all along and its pitch coarser (0.132 against 0.123 in), another spring or another run."}},"bumper_length":{"label":"Length of the polymer bumper, from the end cap to its front face","kind":"length","measurements":[{"id":"photo","value":0.979,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/jp-silent-captured-spring-gen2 3431b2d79bca","scaleRef":"292.0 px/in (.length)","method":"px 94 (where the black cap ends) to px 380 (the front face, where the silhouette meets the spring's), 286 px","via":"harvest"}},{"id":"pa","value":0.969,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/jp-silent-captured-spring-gen2 0b290578345a (Primary Arms' JPSCS2-15_01 on its page for the standard, the same picture at Dirty Bird and AR15Discounts: the unit square to its side on white, 2000 x 1333, front at the left)","scaleRef":"232.2 px/in (.length over 1683 px)","method":"px 1589 (the front face, where the silhouette meets the spring's) to px 1814 (where the cap's black begins), 225 px","via":"harvest"}}],"adopt":{"from":"photo","reason":"The two agree inside their ±; MidwayUSA's, the photo the bumper's diameters are read on."}},"bumper_rear_d":{"label":"The bumper's diameter at its rear (it tapers toward the front)","kind":"length","measurements":[{"id":"photo","value":0.993,"unit":"in","pm":0.016,"source":{"type":"photo","photo":"references/jp-silent-captured-spring-gen2 3431b2d79bca","scaleRef":"292.0 px/in (.length)","method":"290 px at px 118 to 150, beside the cap's 291","via":"harvest"}}]},"bumper_front_d":{"label":"The bumper's diameter at its front face","kind":"length","measurements":[{"id":"photo","value":0.918,"unit":"in","pm":0.016,"source":{"type":"photo","photo":"references/jp-silent-captured-spring-gen2 3431b2d79bca","scaleRef":"292.0 px/in (.length)","method":"268 px at px 352, falling evenly from 290 at px 118 (283 at 200, 277 at 250, 273 at 300)","via":"harvest"}}]},"bumper_front_round":{"label":"The round on the bumper's front edge","kind":"length","measurements":[{"id":"photo","value":0.06,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/jp-silent-captured-spring-gen2 3431b2d79bca","scaleRef":"292.0 px/in (.length)","method":"the silhouette falls over 28 px (px 352 to 380), of which the face itself, seen a few degrees off edge-on, is about 10","via":"harvest"}}]},"cap_d":{"label":"Diameter of the black end cap at the rear","kind":"length","measurements":[{"id":"photo","value":0.996,"unit":"in","pm":0.016,"source":{"type":"photo","photo":"references/jp-silent-captured-spring-gen2 3431b2d79bca","scaleRef":"292.0 px/in (.length)","method":"291 px, px 79 to 94","via":"harvest"}}]},"cap_length":{"label":"Length of the end cap","kind":"length","measurements":[{"id":"photo","value":0.161,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/jp-silent-captured-spring-gen2 3431b2d79bca","scaleRef":"292.0 px/in (.length)","method":"px 47 (the rear end) to px 94, 47 px, black throughout","via":"harvest"}},{"id":"pa","value":0.116,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/jp-silent-captured-spring-gen2 0b290578345a (Primary Arms' JPSCS2-15_01 on its page for the standard, the same picture at Dirty Bird and AR15Discounts: the unit square to its side on white, 2000 x 1333, front at the left)","scaleRef":"232.2 px/in (.length over 1683 px)","method":"the black band from where the pale bumper ends (px 1814) to the rear end (px 1841), 27 px, its rear rim's round 9 px of it","via":"harvest"}}],"adopt":{"from":"pa","reason":"The cap's band at full height is the same in both photos (23 px at 292.0 and 18 px at 232.2: 0.079 and 0.078 in); in MidwayUSA's the rear rim adds 24 px more, in Primary Arms' 9: its lens stood nearer, and the face's rim it sees past the edge isn't the cap's length."}},"cap_round":{"label":"The round on the end cap's rear edge","kind":"length","measurements":[{"id":"photo","value":0.05,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/jp-silent-captured-spring-gen2 3431b2d79bca","scaleRef":"292.0 px/in (.length)","method":"the silhouette rises from 118 px at px 49 to its full height at px 73: 24 px, of which the rear face's rim, seen a few degrees off edge-on, is part","via":"harvest"}},{"id":"pa","value":0.035,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/jp-silent-captured-spring-gen2 0b290578345a (Primary Arms' JPSCS2-15_01 on its page for the standard, the same picture at Dirty Bird and AR15Discounts: the unit square to its side on white, 2000 x 1333, front at the left)","scaleRef":"232.2 px/in (.length over 1683 px)","method":"the silhouette falls from full height to the end over 9 px (px 1832 to 1841): no more than that is the round","via":"harvest"}}],"adopt":{"from":"pa","reason":"The smaller of the two: what the end's silhouette falls over is the round and, more in the nearer lens's photo, the rear face's rim."}},"cap_pocket_d":{"label":"The pocket in the end cap's rear face that the rear screw's head sits in","kind":"length","measurements":[{"id":"photo","value":0.42,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/jp-silent-captured-spring-gen2 0c20449e5d5c (Primary Arms' JPSCS2-15H2_02, the H2 from behind its end cap, 2200 x 1467: the same cap as the standard's, \"US 8,800,424\" on its face)","scaleRef":"the cap's own diameter (.cap_d) across the face's ellipse","method":"the pocket's long axis over the face's along the same line, 0.42, read on a crop at twice the size","via":"harvest"}}]},"screw_head_d":{"label":"The rear screw's head","kind":"length","measurements":[{"id":"photo","value":0.36,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/jp-silent-captured-spring-gen2 0c20449e5d5c","scaleRef":"the cap's own diameter (.cap_d) across the face's ellipse","method":"the head's long axis inside the pocket over the face's, 0.36","via":"harvest"}}]},"hex_socket":{"label":"The screws' hex socket, across its flats","kind":"length","measurements":[{"id":"jp","value":0.125,"unit":"in","pm":0.002,"stated":"GEN 2 SCS units take a 1/8 hex wrench.","source":{"type":"spec","publisher":"manufacturer","name":"JP Enterprises, Buffer Springs and Silent Captured Springs (FAQ)","url":"https://jprifles.com/1.4.7.2_os.php?menu_select=scs_guide","retrieved":"2026-10-18","via":"harvest"},"note":"On the H2's end cap (0c20449e5d5c) the socket reads 0.13 of an inch by the cap's own diameter: the same. The kit's sheet calls the front screw \"this 10-32 screw\" with \"a T25 key\", which is another production's."},{"id":"guide","value":0.118,"unit":"in","pm":0.002,"stated":"Before disassembly, note that the SCS screws are metric and require a 3mm hex key.","source":{"type":"spec","publisher":"manufacturer","name":"JP Enterprises, Silent Captured Spring Selection Guide (Ver. 11.24, \"the GEN 2 Silent Captured Spring System\"), page 6, V Compatibility Modifications, Changing Springs","url":"https://jprifles.com/document_pdfs/SCS%20Selection%20Guide_899.pdf","retrieved":"2026-10-18","via":"harvest"},"note":"3 mm. The FAQ says this is the first generation's: \"The screws on the first generation JPSCS are metric (M5) and take a 3mm hex key.\""}],"adopt":{"from":"jp","reason":"The FAQ names the GEN 2's key and gives the 3 mm to the first generation, whose sentence the guide carries over; the H2's end cap reads 0.13 in across its socket, nearer 1/8 than 3 mm."}},"pocket_depth":{"label":"Depth of the end cap's pocket to the screw's head","kind":"length","measurements":[{"id":"assumed","value":0.05,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the H2's rear view (0c20449e5d5c) has the head a little below the face, and no view shows it in section.","via":"harvest"}}]}}},{"subject":"kynshot-rb5000","title":"KynSHOT RB5000","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"kynshot","value":4.2,"unit":"oz","stated":"Weight: 4.2 Ounces","source":{"type":"spec","publisher":"manufacturer","name":"KynSHOT, KynSHOT RB5000 (product page, Specifications)","url":"https://www.kynshot.com/products/our-products/kynshot-rb5000-9/","retrieved":"2026-10-18","via":"harvest"}},{"id":"midwayusa","value":4.2,"unit":"oz","stated":"\"name\":\"Weight\",\"value\":\"4.2 Ounce\"","source":{"type":"spec","publisher":"retailer","name":"MidwayUSA, KynSHOT Hydraulic AR-15 Carbine Recoil Buffer 3.25\" (product 614230, its attributes)","url":"https://www.midwayusa.com/product/1024517165","retrieved":"2026-10-18","via":"harvest"}},{"id":"all4shooters","value":4.162,"unit":"oz","pm":0.018,"stated":"The RB5000 is slightly heavier than a standard .223 M4 buffer, at 118 g.","source":{"type":"spec","publisher":"review","name":"all4shooters, \"Test: Kynshot Hydraulic buffer for AR guns\" (Franco Palamaro, 2019-07-24)","url":"https://www.all4shooters.com/en/shooting/accessories/kynshot-hydraulic-buffer-for-ar-guns/","retrieved":"2026-10-18","via":"harvest"},"note":"118 g is 4.162 oz; the review doesn't say whether it was weighed or copied."},{"id":"primary-arms","value":3,"unit":"oz","stated":"Weight 3 oz.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Kynshot AR-15 Recoil Damper - Carbine (Specifications)","url":"https://www.primaryarms.com/kynshot-precision-carbine-recoil-damper-for-5-56-223-rb5000","retrieved":"2026-10-18","via":"harvest"},"note":"A shop's attribute that no other source bears out (its own row, \"Buffer Standard Carbine\", is a category, and a standard carbine buffer is 3.0 oz)."},{"id":"ar15discounts","value":5.44,"unit":"oz","stated":"Weight 5.44 oz Dimensions 3.65 × 0.69 × 0.69 in","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, KynSHOT Precision Carbine Recoil Damper For 5.56 / .223 (Additional information)","url":"https://ar15discounts.com/products/kynshot-precision-carbine-recoil-damper-for-5-56-223/","retrieved":"2026-10-18","via":"harvest"},"note":"A shipping weight, by its size: MidwayUSA ships it at \"0.342 Pounds\" (5.48 oz)."}],"adopt":{"from":"kynshot","reason":"The maker's figure; MidwayUSA states the same, and all4shooters' 118 g is within its last digit. Primary Arms' 3 oz is a standard carbine buffer's weight, and AR15Discounts' 5.44 oz is the boxed weight MidwayUSA ships it at."}},"length":{"label":"Length at rest (the head's front face to the bumper's end, the piston rod out)","kind":"length","measurements":[{"id":"kynshot","value":3.65,"unit":"in","stated":"Overall length: 3.65\"","source":{"type":"spec","publisher":"manufacturer","name":"KynSHOT, KynSHOT RB5000 (product page, Specifications)","url":"https://www.kynshot.com/products/our-products/kynshot-rb5000-9/","retrieved":"2026-10-18","via":"harvest"}},{"id":"ar15discounts","value":3.65,"unit":"in","stated":"Dimensions 3.65 × 0.69 × 0.69 in","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, KynSHOT Precision Carbine Recoil Damper For 5.56 / .223 (Additional information)","url":"https://ar15discounts.com/products/kynshot-precision-carbine-recoil-damper-for-5-56-223/","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"kynshot","reason":"The maker's figure; the seller's is the same."},"note":"What it is drawn at: in a rifle with the bolt forward the spring holds the rod out, and the carrier rests on the head. all4shooters: \"The Kynshot, when extended, is longer than a standard buffer, and pulling back the bolt will result in the buffer contacting the rear end of the buffer tube too soon\"."},"compressed_length":{"label":"Length pushed in (the piston rod in)","kind":"length","measurements":[{"id":"kynshot","value":3.25,"unit":"in","stated":"Length when compressed: 3.25”","source":{"type":"spec","publisher":"manufacturer","name":"KynSHOT, KynSHOT RB5000 (product page, Specifications)","url":"https://www.kynshot.com/products/our-products/kynshot-rb5000-9/","retrieved":"2026-10-18","via":"harvest"}}]},"od":{"label":"Diameter (its body: the maker's \"Buffer diameter\")","kind":"length","measurements":[{"id":"kynshot","value":0.69,"unit":"in","stated":"Buffer diameter: .69\"","source":{"type":"spec","publisher":"manufacturer","name":"KynSHOT, KynSHOT RB5000 (product page, Specifications)","url":"https://www.kynshot.com/products/our-products/kynshot-rb5000-9/","retrieved":"2026-10-18","via":"harvest"}},{"id":"ar15discounts","value":0.69,"unit":"in","stated":"Dimensions 3.65 × 0.69 × 0.69 in","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, KynSHOT Precision Carbine Recoil Damper For 5.56 / .223 (Additional information)","url":"https://ar15discounts.com/products/kynshot-precision-carbine-recoil-damper-for-5-56-223/","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"kynshot","reason":"The maker's figure; the seller's is the same."},"note":"The body's. Its head, which runs in the receiver extension's bore, is larger: head_d."},"head_d":{"label":"Its head (the disc the carrier meets), diameter","kind":"length","measurements":[{"id":"photo","value":0.951,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/kynshot-rb5000 ef0c90ef9af5 (MidwayUSA 614230.jpg, 880 x 660, upright, nearly square, engraved \"P/N RB5000 20223\")","scaleRef":"the body's 117.5 px for the maker's .69 in, in the same view (both polished steel, read thin alike)","method":"the disc's width across the axis, 160 to 164 px along its rim (.cache/batch12/kynshot/edges.py: the silhouette's top and bottom per column)","via":"harvest"},"note":"Read at the length scale it is 0.921 in, 3.2% thin, as the body is. Its maker's own photo (823ba35382b7, from above, the head furthest from the lens) has the disc 1.34 times the body: 0.925, a little small for being further off. The RB5000HP's reads 0.982 on its own photo: the two heads differ."}]},"head_flats":{"label":"Its head: the flats round its rim (count)","kind":"count","measurements":[{"id":"photo","value":3,"unit":"count","source":{"type":"photo","photo":"references/kynshot-rb5000 800fcb7d6a49 (Impact Guns RSRKYNRB5000-1, 2000 px: the buffer upright, the head toward the lens and seen from above, engraved 25057)","scaleRef":"none: a count","method":"two flats seen at once, one each side of the lens's line and as far round as each other (each about 60 degrees off it), with the round between them: three equally spaced has the third behind; the maker's photo (823ba35382b7) and the HP's three views show one flat or two in each, never a third beside them","via":"harvest"},"note":"No view on file looks along the axis at the face, so the whole turn isn't seen: three is what two flats 120 degrees apart, each alone in other views, come to. The standard buffer's head has three (std.carbine_buffer.head_flat_across)."}]},"head_flat_across":{"label":"Its head: from one flat to the round opposite","kind":"length","measurements":[{"id":"photo","value":0.924,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/kynshot-rb5000 800fcb7d6a49 (Impact Guns RSRKYNRB5000-1, 2000 px: the head toward the lens, seen from above)","scaleRef":"the disc's width across, 520 px, for head_d (0.951 in)","method":"the two flats' spans across the image, 90 and 80 px: two flats 60 degrees each side of the lens's line show their chord times cos 60 each, so their sum is one chord, 0.31 in, whatever small turn the part has; a chord of 0.31 in on a 0.951 in circle stands 0.449 from the axis","via":"harvest"}}]},"head_rim":{"label":"Its head: the length of its full diameter, from the front face","kind":"length","measurements":[{"id":"photo","value":0.193,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/kynshot-rb5000 ef0c90ef9af5 (MidwayUSA 614230.jpg)","scaleRef":"175.9 px/in along the axis (the maker's 3.65 in between the face's and the bumper's end's planes)","method":"the silhouette's edges at the disc's full width, from the face's plane (row 10) to where they begin to fall (row 44): 34 px","via":"harvest"}}]},"head_thickness":{"label":"Its head: front face to its rear face (where the spring bears)","kind":"length","measurements":[{"id":"photo","value":0.244,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/kynshot-rb5000 ef0c90ef9af5 (MidwayUSA 614230.jpg)","scaleRef":"175.9 px/in along the axis","method":"from the face's plane (row 10) to the foot of the rim's rear bevel, where the edges reach the hub (row 53): 43 px","via":"harvest"},"note":"The standard carbine buffer's head is 0.254 (std.carbine_buffer.head_thickness): the catalog's spring, drawn from there, stands 0.01 in behind this one's face."}]},"head_back_d":{"label":"Its head: where the bevel behind its rim meets its rear face, diameter","kind":"length","measurements":[{"id":"photo","value":0.79,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/kynshot-rb5000 ef0c90ef9af5 (MidwayUSA 614230.jpg)","scaleRef":"the body's 117.5 px for .69 in","method":"the edges fall 14 px each side from the rim (rows 44 to 53) before they reach the hub: 0.951 less twice 0.082","via":"harvest"}}]},"head_front_chamfer":{"label":"Its head: the bevel round its front face","kind":"length","measurements":[{"id":"assumed","value":0.015,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: a bright line round the face's edge in Impact Guns' views from above (800fcb7d6a49) and MidwayUSA's, a few pixels across; no view on file shows it in profile.","via":"harvest"}}]},"hub_d":{"label":"Its hub (behind the head, round the rod), diameter","kind":"length","measurements":[{"id":"photo","value":0.74,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/kynshot-rb5000 ef0c90ef9af5 (MidwayUSA 614230.jpg)","scaleRef":"the body's 117.5 px for .69 in","method":"the hub's width across the axis, 126 px (rows 55 to 71)","via":"harvest"},"note":"The spring's end coil sits over it, as over a standard buffer's pilot (0.781, std.carbine_buffer.pilot_d)."}]},"hub_length":{"label":"Its hub: length (the head's rear face to the hub's rear face)","kind":"length","measurements":[{"id":"photo","value":0.136,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/kynshot-rb5000 ef0c90ef9af5 (MidwayUSA 614230.jpg)","scaleRef":"175.9 px/in along the axis","method":"rows 53 to 77, where the edges drop to the rod's: 24 px","via":"harvest"}}]},"hub_chamfer":{"label":"Its hub: the bevel round its rear face","kind":"length","measurements":[{"id":"photo","value":0.017,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/kynshot-rb5000 ef0c90ef9af5 (MidwayUSA 614230.jpg)","scaleRef":"175.9 px/in along the axis","method":"the edges turn in over 3 px (rows 71 to 74) before the rear face","via":"harvest"}}]},"hub_hole_d":{"label":"Its hub: the hole across it (a set screw in it), diameter","kind":"length","measurements":[{"id":"photo","value":0.09,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/kynshot-rb5000 800fcb7d6a49 (Impact Guns RSRKYNRB5000-1: a hole each side of the hub, threaded)","scaleRef":"the disc's 520 px across for head_d (0.951 in)","method":"each hole's height, about 50 px","via":"harvest"}}]},"screw_sink":{"label":"Its hub: how far the set screw's end stands below the hub's surface","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: a socket screw's end a little inside its hole in the RB5000HP's side photo (3bf8c2301cf9); the RB5000's own photos show the holes, not how deep the screw is.","via":"harvest"}}]},"rod_d":{"label":"Its piston rod, diameter","kind":"length","measurements":[{"id":"photo","value":0.167,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/kynshot-rb5000 ef0c90ef9af5 (MidwayUSA 614230.jpg)","scaleRef":"the body's 117.5 px for .69 in","method":"the rod's width across the axis, 27 to 30 px (rows 79 to 133)","via":"harvest"}}]},"rod_exposed":{"label":"Its piston rod: how far it stands out of the body at rest (the hub's rear face to the body's front face)","kind":"length","measurements":[{"id":"photo","value":0.324,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/kynshot-rb5000 ef0c90ef9af5 (MidwayUSA 614230.jpg)","scaleRef":"175.9 px/in along the axis","method":"rows 77 to 134, where the edges leave the rod for the body's front: 57 px","via":"harvest"}}],"note":"Less than the 0.40 in the maker's two lengths differ by (3.65 at rest, 3.25 pushed in): pushed home, the hub would meet the body 0.08 in short of 3.25. What takes up the rest (the bumper giving, or a hub that enters the body's mouth) isn't on file: the model is drawn at rest, where it doesn't matter."},"body_length":{"label":"Its body: front face to rear face (where the bumper stands out)","kind":"length","measurements":[{"id":"photo","value":2.666,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/kynshot-rb5000 ef0c90ef9af5 (MidwayUSA 614230.jpg)","scaleRef":"175.9 px/in along the axis","method":"rows 134 to 603, where the black bumper begins: 469 px","via":"harvest"}}]},"body_front_chamfer":{"label":"Its body: the bevel round its front face","kind":"length","measurements":[{"id":"photo","value":0.025,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/kynshot-rb5000 ef0c90ef9af5 (MidwayUSA 614230.jpg)","scaleRef":"175.9 px/in along the axis","method":"the edges reach the body's full width 12 px behind its front face, 8 of them the face's own ellipse (r sin e)","via":"harvest"}}]},"body_rear_chamfer":{"label":"Its body: the bevel round its rear face","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: a narrow bright band where the body meets the bumper in MidwayUSA's photo, too small to read against the bumper beside it.","via":"harvest"}}]},"mouth_wall":{"label":"Its body's mouth: the wall left round the bore the rod comes out of","kind":"length","measurements":[{"id":"assumed","value":0.04,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: a thin bright ring round a dark bore at the body's front in Impact Guns' views from above (800fcb7d6a49, 6171514cab7b) and the RB5000HP's side photo; no view looks into it square.","via":"harvest"}}]},"mouth_depth":{"label":"Its body's mouth: how deep the seal stands inside it","kind":"length","measurements":[{"id":"assumed","value":0.06,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the seal and the ring that holds it (all4shooters: \"the Seeger ring that locks the hydraulic cartridge in the buffer's body\") are a little way inside the mouth in every view; none shows how far.","via":"harvest"}}]},"bumper_exposed":{"label":"Its bumper: how far it stands out of the body","kind":"length","measurements":[{"id":"photo","value":0.279,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/kynshot-rb5000 ef0c90ef9af5 (MidwayUSA 614230.jpg)","scaleRef":"175.9 px/in along the axis","method":"rows 603 to 652 (the end's plane, 5 px in from the silhouette's tip): 49 px","via":"harvest"}}]},"bumper_d":{"label":"Its bumper: diameter where it leaves the body","kind":"length","measurements":[{"id":"photo","value":0.67,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/kynshot-rb5000 ef0c90ef9af5 (MidwayUSA 614230.jpg)","scaleRef":"175.9 px/in (matte rubber, read at the length scale) and the body's 117.5 px for .69 in","method":"116 px at its shoulder: 0.66 at the length scale, 0.68 against the body","via":"harvest"}}]},"bumper_end_d":{"label":"Its bumper: diameter where its taper meets the round of its end","kind":"length","measurements":[{"id":"photo","value":0.53,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/kynshot-rb5000 ef0c90ef9af5 (MidwayUSA 614230.jpg)","scaleRef":"175.9 px/in along the axis (matte rubber)","method":"93 px at row 644, 0.233 in behind the body, where its edges begin to round in","via":"harvest"}}]},"bumper_round":{"label":"Its bumper: the round from its taper onto its end face","kind":"length","measurements":[{"id":"assumed","value":0.045,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the end's edges round in over the last 8 px (rows 644 to 652) of MidwayUSA's photo, the end face flat inside them in Impact Guns' (6171514cab7b).","via":"harvest"}}]},"screw_socket":{"label":"Its set screw: the hex socket in its end, across the flats","kind":"length","measurements":[{"id":"assumed","value":0.05,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the RB5000HP's side photo (3bf8c2301cf9) shows a hex socket filling about half the screw's end; its size isn't read.","via":"harvest"}}]},"screw_socket_depth":{"label":"Its set screw: how deep its hex socket is","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view looks into the socket.","via":"harvest"}}]}}},{"subject":"kynshot-rb5000hp","title":"KynSHOT RB5000HP (High Performance)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"kynshot","value":4.8,"unit":"oz","stated":"Weight: 4.8 Ounces","source":{"type":"spec","publisher":"manufacturer","name":"KynSHOT, KynSHOT RB5000HP (High Performance) (product page, Specifications)","url":"https://www.kynshot.com/products/our-products/kynshot-rb5000hp-high-performance-96/","retrieved":"2026-10-18","via":"harvest"}},{"id":"midwayusa","value":4.8,"unit":"oz","stated":"\"name\":\"Weight\",\"value\":\"4.8 Ounce\"","source":{"type":"spec","publisher":"retailer","name":"MidwayUSA, KynSHOT Hydraulic High Performance AR-15 Carbine Recoil Buffer 3.25\" (product 418309, its attributes)","url":"https://www.midwayusa.com/product/1024517262","retrieved":"2026-10-18","via":"harvest"}},{"id":"ar15discounts","value":6.08,"unit":"oz","stated":"Weight 6.08 oz Dimensions 3.69 × 0.76 × 0.76 in","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, KynSHOT Precision High-Performance Carbine Recoil Damper For 5.56/.223 (Additional information)","url":"https://ar15discounts.com/products/kynshot-precision-high-performance-carbine-recoil-damper-for-5-56-223/","retrieved":"2026-10-18","via":"harvest"},"note":"A shipping weight, by its size: MidwayUSA ships it at \"0.378 Pounds\" (6.05 oz)."}],"adopt":{"from":"kynshot","reason":"The maker's figure; MidwayUSA states the same. AR15Discounts' 6.08 oz is the boxed weight MidwayUSA ships it at."}},"length":{"label":"Length at rest (the head's front face to the bumper's end, the piston rod out)","kind":"length","measurements":[{"id":"kynshot","value":3.69,"unit":"in","stated":"Overall length: 3.69\"","source":{"type":"spec","publisher":"manufacturer","name":"KynSHOT, KynSHOT RB5000HP (High Performance) (product page, Specifications)","url":"https://www.kynshot.com/products/our-products/kynshot-rb5000hp-high-performance-96/","retrieved":"2026-10-18","via":"harvest"}},{"id":"ar15discounts","value":3.69,"unit":"in","stated":"Dimensions 3.69 × 0.76 × 0.76 in","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, KynSHOT Precision High-Performance Carbine Recoil Damper For 5.56/.223 (Additional information)","url":"https://ar15discounts.com/products/kynshot-precision-high-performance-carbine-recoil-damper-for-5-56-223/","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"kynshot","reason":"The maker's figure; the seller's is the same."}},"compressed_length":{"label":"Length pushed in (the piston rod in)","kind":"length","measurements":[{"id":"kynshot","value":3.25,"unit":"in","stated":"Length when compressed: 3.25”","source":{"type":"spec","publisher":"manufacturer","name":"KynSHOT, KynSHOT RB5000HP (High Performance) (product page, Specifications)","url":"https://www.kynshot.com/products/our-products/kynshot-rb5000hp-high-performance-96/","retrieved":"2026-10-18","via":"harvest"}},{"id":"midwayusa","value":3.25,"unit":"in","stated":"\"name\":\"Length Collapsed\",\"value\":\"3.25\\\"\"","source":{"type":"spec","publisher":"retailer","name":"MidwayUSA, KynSHOT Hydraulic High Performance AR-15 Carbine Recoil Buffer 3.25\" (product 418309, its attributes)","url":"https://www.midwayusa.com/product/1024517262","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"kynshot","reason":"The maker's figure; the seller's is the same."}},"od":{"label":"Diameter (its body: the maker's \"Buffer diameter\")","kind":"length","measurements":[{"id":"kynshot","value":0.76,"unit":"in","stated":"Buffer diameter: .76\"","source":{"type":"spec","publisher":"manufacturer","name":"KynSHOT, KynSHOT RB5000HP (High Performance) (product page, Specifications)","url":"https://www.kynshot.com/products/our-products/kynshot-rb5000hp-high-performance-96/","retrieved":"2026-10-18","via":"harvest"}},{"id":"ar15discounts","value":0.76,"unit":"in","stated":"Dimensions 3.69 × 0.76 × 0.76 in","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, KynSHOT Precision High-Performance Carbine Recoil Damper For 5.56/.223 (Additional information)","url":"https://ar15discounts.com/products/kynshot-precision-high-performance-carbine-recoil-damper-for-5-56-223/","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"kynshot","reason":"The maker's figure; the seller's is the same."},"note":"The body's. Its head, which runs in the receiver extension's bore, is larger: head_d."},"head_d":{"label":"Its head (the disc the carrier meets), diameter","kind":"length","measurements":[{"id":"photo","value":0.982,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/kynshot-rb5000hp 3bf8c2301cf9 (AR15Discounts RB5000HB.jpg, 1920 x 1280, level, nearly square, engraved \"P/N: RB5000HP 20217\")","scaleRef":"the body's 223.6 px for the maker's .76 in, in the same view (both polished steel)","method":"the disc's width across the axis, 288 to 290 px along its rim (.cache/batch12/kynshot/edges.py)","via":"harvest"},"note":"At the length scale 0.970, 1.2% thin as the body is. The maker's photo (57086653f522, from above) has the disc 1.30 times the body: 0.99. The RB5000's reads 0.951 on its own photo."}]},"head_flats":{"label":"Its head: the flats round its rim (count)","kind":"count","measurements":[{"id":"photo","value":3,"unit":"count","source":{"type":"photo","photo":"references/kynshot-rb5000hp 270a10eca7ff (Impact Guns RSRKYNRB5000HP-1, 2000 px: the buffer upright, the head toward the lens and seen from above)","scaleRef":"none: a count","method":"two flats seen at once, one each side of the lens's line and as far round as each other, the round between them: three equally spaced has the third behind; the maker's photo (57086653f522) and Impact Guns' three-quarter view (790e8838b506) each show one","via":"harvest"},"note":"No view on file looks along the axis at the face: the whole turn isn't seen."}]},"head_flat_across":{"label":"Its head: from one flat to the round opposite","kind":"length","measurements":[{"id":"photo","value":0.945,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/kynshot-rb5000hp 270a10eca7ff (Impact Guns RSRKYNRB5000HP-1, 2000 px)","scaleRef":"the disc's width across, 523 px, for head_d (0.982 in)","method":"the two flats' spans across the image, 97 px each: their sum is one chord (each shows it times cos 60), 0.364 in, which on a 0.982 in circle stands 0.455 from the axis","via":"harvest"}}]},"head_rim":{"label":"Its head: the length of its full diameter, from the front face","kind":"length","measurements":[{"id":"photo","value":0.205,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/kynshot-rb5000hp 3bf8c2301cf9 (AR15Discounts RB5000HB.jpg)","scaleRef":"297.8 px/in along the axis (the maker's 3.69 in between the face's and the bumper's end's planes)","method":"columns 366 to 427, where the edges begin to fall: 61 px","via":"harvest"}}]},"head_thickness":{"label":"Its head: front face to its rear face (where the spring bears)","kind":"length","measurements":[{"id":"photo","value":0.238,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/kynshot-rb5000hp 3bf8c2301cf9 (AR15Discounts RB5000HB.jpg)","scaleRef":"297.8 px/in along the axis","method":"columns 366 to 437, the foot of the rim's rear bevel: 71 px","via":"harvest"},"note":"The standard carbine buffer's head is 0.254: the catalog's spring, drawn from there, stands 0.016 in behind this one's face."}]},"head_back_d":{"label":"Its head: where the bevel behind its rim meets its rear face, diameter","kind":"length","measurements":[{"id":"photo","value":0.82,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/kynshot-rb5000hp 3bf8c2301cf9 (AR15Discounts RB5000HB.jpg)","scaleRef":"the body's 223.6 px for .76 in","method":"the top edge falls 24 px from the rim (columns 427 to 437) before it reaches the hub: 0.982 less twice 0.081","via":"harvest"}}]},"head_front_chamfer":{"label":"Its head: the bevel round its front face","kind":"length","measurements":[{"id":"photo","value":0.02,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/kynshot-rb5000hp 3bf8c2301cf9 (AR15Discounts RB5000HB.jpg)","scaleRef":"297.8 px/in along the axis","method":"a bright band round the face's edge, about 6 px across on a 3x crop of the head (.cache/batch12/kynshot/hp03-head.png)","via":"harvest"}}]},"hub_d":{"label":"Its hub (behind the head, round the rod), diameter","kind":"length","measurements":[{"id":"photo","value":0.768,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/kynshot-rb5000hp 3bf8c2301cf9 (AR15Discounts RB5000HB.jpg)","scaleRef":"the body's 223.6 px for .76 in","method":"the hub's width across the axis, 226 px (columns 447 to 469)","via":"harvest"}}]},"hub_length":{"label":"Its hub: length (the head's rear face to the hub's rear face)","kind":"length","measurements":[{"id":"photo","value":0.141,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/kynshot-rb5000hp 3bf8c2301cf9 (AR15Discounts RB5000HB.jpg)","scaleRef":"297.8 px/in along the axis","method":"columns 437 to 479, where the edges drop to the rod's: 42 px","via":"harvest"}}]},"hub_chamfer":{"label":"Its hub: the bevel round its rear face","kind":"length","measurements":[{"id":"photo","value":0.03,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/kynshot-rb5000hp 3bf8c2301cf9 (AR15Discounts RB5000HB.jpg)","scaleRef":"297.8 px/in along the axis","method":"the edges turn in over columns 469 to 478, 9 px, before the rear face","via":"harvest"}}]},"hub_hole_d":{"label":"Its hub: the hole across it (a set screw in it), diameter","kind":"length","measurements":[{"id":"photo","value":0.1,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/kynshot-rb5000hp 270a10eca7ff (Impact Guns RSRKYNRB5000HP-1: a hole each side of the hub, one threaded and empty to the eye)","scaleRef":"the disc's 523 px across for head_d (0.982 in)","method":"each hole's height, about 53 px; the side photo (3bf8c2301cf9) has the socket screw's hole about 33 px across, 0.11 in","via":"harvest"}}]},"screw_sink":{"label":"Its hub: how far the set screw's end stands below the hub's surface","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the socket screw's end is a little inside its hole in the side photo (3bf8c2301cf9); how far isn't seen in profile.","via":"harvest"}}]},"rod_d":{"label":"Its piston rod, diameter","kind":"length","measurements":[{"id":"photo","value":0.194,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/kynshot-rb5000hp 3bf8c2301cf9 (AR15Discounts RB5000HB.jpg)","scaleRef":"the body's 223.6 px for .76 in","method":"the rod's width across the axis, 56 to 57 px (columns 492 to 570)","via":"harvest"}}]},"rod_exposed":{"label":"Its piston rod: how far it stands out of the body at rest (the hub's rear face to the body's front face)","kind":"length","measurements":[{"id":"photo","value":0.332,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/kynshot-rb5000hp 3bf8c2301cf9 (AR15Discounts RB5000HB.jpg)","scaleRef":"297.8 px/in along the axis","method":"columns 479 to 578, where the edges leave the rod for the body's front rim: 99 px","via":"harvest"}}],"note":"Less than the 0.44 in the maker's two lengths differ by (3.69 at rest, 3.25 pushed in): pushed home, the hub would meet the body 0.11 in short of 3.25. What takes up the rest isn't on file; the model is drawn at rest."},"body_length":{"label":"Its body: front face to rear face (where the bumper stands out)","kind":"length","measurements":[{"id":"photo","value":2.68,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/kynshot-rb5000hp 3bf8c2301cf9 (AR15Discounts RB5000HB.jpg)","scaleRef":"297.8 px/in along the axis","method":"columns 578 to 1376, the foot of its rear bevel where the black bumper begins: 798 px","via":"harvest"}}]},"body_front_chamfer":{"label":"Its body: the bevel round its front face","kind":"length","measurements":[{"id":"photo","value":0.03,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/kynshot-rb5000hp 3bf8c2301cf9 (AR15Discounts RB5000HB.jpg)","scaleRef":"297.8 px/in along the axis","method":"the bright bevel at the body's front, about 8 px wide along the top edge on a 3x crop (.cache/batch12/kynshot/hp03-mouth.png)","via":"harvest"}}]},"body_rear_chamfer":{"label":"Its body: the bevel round its rear face","kind":"length","measurements":[{"id":"photo","value":0.03,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/kynshot-rb5000hp 3bf8c2301cf9 (AR15Discounts RB5000HB.jpg)","scaleRef":"297.8 px/in along the axis","method":"the top edge falls 9 px over columns 1366 to 1376, from the body's width toward the bumper's","via":"harvest"}}]},"mouth_wall":{"label":"Its body's mouth: the wall left round the bore the rod comes out of","kind":"length","measurements":[{"id":"assumed","value":0.04,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: a thin bright ring round a dark bore at the body's front in the side photo (3bf8c2301cf9, its face's ellipse) and Impact Guns' view from above (270a10eca7ff); no view looks into it square.","via":"harvest"}}]},"mouth_depth":{"label":"Its body's mouth: how deep the seal stands inside it","kind":"length","measurements":[{"id":"assumed","value":0.06,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: Impact Guns' view from above (270a10eca7ff) shows a ring and a dark seal round the rod a little way inside the mouth; how far isn't seen in profile.","via":"harvest"}}]},"bumper_exposed":{"label":"Its bumper: how far it stands out of the body","kind":"length","measurements":[{"id":"photo","value":0.299,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/kynshot-rb5000hp 3bf8c2301cf9 (AR15Discounts RB5000HB.jpg)","scaleRef":"297.8 px/in along the axis","method":"columns 1376 to 1465 (the end's plane): 89 px","via":"harvest"}}]},"bumper_d":{"label":"Its bumper: diameter where it leaves the body","kind":"length","measurements":[{"id":"photo","value":0.7,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/kynshot-rb5000hp 3bf8c2301cf9 (AR15Discounts RB5000HB.jpg)","scaleRef":"297.8 px/in along the axis (matte rubber, read at the length scale)","method":"209 px at its shoulder (column 1378)","via":"harvest"}}]},"bumper_end_d":{"label":"Its bumper: diameter where its taper meets the round of its end","kind":"length","measurements":[{"id":"photo","value":0.557,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/kynshot-rb5000hp 3bf8c2301cf9 (AR15Discounts RB5000HB.jpg)","scaleRef":"297.8 px/in along the axis (matte rubber)","method":"166 px at column 1450, 0.25 in behind the body, where its edges begin to round in","via":"harvest"}}]},"bumper_round":{"label":"Its bumper: the round from its taper onto its end face","kind":"length","measurements":[{"id":"photo","value":0.05,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/kynshot-rb5000hp 3bf8c2301cf9 (AR15Discounts RB5000HB.jpg)","scaleRef":"297.8 px/in along the axis","method":"the edges round in over columns 1450 to 1465, 15 px","via":"harvest"}}]},"screw_socket":{"label":"Its set screw: the hex socket in its end, across the flats","kind":"length","measurements":[{"id":"assumed","value":0.05,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the RB5000HP's side photo (3bf8c2301cf9) shows a hex socket filling about half the screw's end; its size isn't read.","via":"harvest"}}]},"screw_socket_depth":{"label":"Its set screw: how deep its hex socket is","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view looks into the socket.","via":"harvest"}}]}}},{"subject":"larue-mbt-2s","title":"LaRue MBT-2S trigger, straight (LT-MBT-2SSB)","dimensions":{"pin_diameter":{"label":"Trigger pin size","kind":"length","measurements":[{"id":"spec","value":0.154,"unit":"in","stated":"Small Pin (.154\")","source":{"type":"spec","publisher":"manufacturer","name":"LaRue Tactical","url":"https://larue.com/mbt-2-stage-ar-triggers-mc7h/","retrieved":"2026-09-30","via":"harvest"}}]},"face_offset_x":{"label":"Trigger face ahead of the trigger pin (at the exposed blade's mid-height)","kind":"length","measurements":[{"id":"photo","value":0.129,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/larue-mbt-2s 45e00d2ce552 (LaRue MBT-2S-SB, straight side view on white, marked LTMBT-2S-SB; supplied in chat)","scaleRef":"the pivot hole, 46.8 px across (circle through the 50% edge; 46.2–48.0 px at the 65–35% levels) = the 0.154 in pin (larue-mbt-2s.pin_diameter); 303.8 px/in. The hole's running clearance is unsourced; each 0.001 in of it would enlarge the outline 0.65%","method":"front edge of the traced outline at the exposed blade's mid-height, 0.925 in below the pin (tools/trace.py target); ± mostly the rest-angle assumption (the photo's tail edge taken as installed-level; 3° of rotation moves the face ~0.05 in)","via":"user"},"note":"Re-derived 2026-09-30 by tools/trace.py: the prototype read the hole 2 px small (a 78%-white threshold), but the face sits almost under the pin, so the value is unchanged."}],"note":"The finger contact point is taken as the blade's front face halfway down its exposed length (from the lower's underside, 0.451 in below the pin, to the tip, 1.46 in below). The SB blade's front face is straight."},"shoe_face_x":{"label":"Trigger face X (at the finger contact point)","kind":"length","measurements":[{"id":"derived","value":2.057,"unit":"in","source":{"type":"derived","expr":"{bad-workhorse-lower.trigger_pin_x} + {.face_offset_x}","via":"user"}}],"note":"Length of pull is measured from here."},"shoe_width":{"label":"Blade width (Z)","kind":"length","measurements":[{"id":"ar15com","value":0.305,"unit":"in","pm":0.01,"stated":"the trigger face measures 0.305\" wide side to side ... only 15 thousands of an inch wider than mil-spec ... flat with a small chamfer along the sides to break the edges","source":{"type":"spec","publisher":"review","name":"AR15.com, LaRue Tactical subforum, 'LaRue MBT-2S width?' (read through search results; the page returns 403)","url":"https://www.ar15.com/forums/Industry/LaRue-MBT-2S-width-/219-297685/?page=1&anc=bottom","retrieved":"2026-10-01","via":"harvest"}},{"id":"user","value":0.295,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/larue-mbt-2s 3239ad914a00 (the user's own LTMBT-2S-SB standing on its tail on a counter, the bow's face toward the lens, a US quarter lying beside it; 2026-10-05)","scaleRef":"nothing of known size is in the bow's own plane (the quarter lies on the counter, an inch and more under the face). Two things bound it. Its pin bosses, in the same view and a tenth of an inch behind the face, are 237.9 px end to end to the bow's 105.0: 2.27 times it, and they go between the walls of a pocket .690 wide (std.ar15.fcg_pocket_width), so the bow is under 0.305; at the Army's own trigger's .680 it is 0.300. And seen along its height (bd521c1c8184) the trigger is 547.5 px long for the 1.899 in of its traced outline (profiles.side, which the pin's hole scales), its bow end-on 83.1 px: 0.288","method":"the bow's face from side to side, rows 1500 and 1560 (105.0 and 104.9 px), by the two bounds; ± covers both. As a check of where the lens was: at the quarter's own scale (324.6 px/in on the counter) the bow reads 0.3235, so the face is 7 to 9% nearer than the counter: an inch up, from 13 to 15 in","via":"user"},"note":"The user's own trigger, the straight bow. It cannot be the 0.305 of the thread and have its bosses in a standard pocket unless they fill it wall to wall; it agrees with the thread within the two figures' ±."}],"adopt":{"from":"ar15com","reason":"A caliper's figure against a photo's, which agrees with it within its ±: the user's own straight bow reads 0.295 ± 0.012. Which bow the thread measured still isn't on file; the photo says it can't have been much narrower than this one."},"note":"The face's width side to side. The thread (in AR15.com's LaRue Tactical industry subforum) answers its title question with a caliper figure; the page itself returns 403 to readers here, so the text is from search results (2026-10-01): the poster, the date and which bow (curved or the later straight) were measured aren't on file, and the ± covers the variant. A mil-spec bow measures 0.29 in (RECOIL's trigger guide: Stag's mil-spec 'measured 0.29 inches wide'; ALG QMS 'Bow Width: 0.29″'), which the thread's '15 thousands wider than mil-spec' matches. The face is flat with a small chamfer on its sides (the thread; Everyday Marksman: 'sharply-angled corners on the shoe'). Not the 0.25 in sometimes quoted for a mil-spec trigger: that's the body's thickness in the pocket."},"body_width":{"label":"Body thickness (Z), behind and above the bow","kind":"length","measurements":[{"id":"user","value":0.3,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/larue-mbt-2s bd521c1c8184 (the user's own LTMBT-2S-SB and its hammer on a counter, each seen along its own height, a US quarter lying between; 2026-10-05)","scaleRef":"the trigger's own length in the same view, by its traced outline (profiles.side: 1.899 in from the tail's end to the nose's, 547.5 px, 288 px/in), and its pin bosses beside it (192.3 px: 0.438 of them, 0.298 at the Army's .680). The quarter is on the counter, under the trigger","method":"the body from side to side at row 1100 (columns 941.0 to 1025.2: 84.2 px): 0.292 by the outline's length, 0.298 by the bosses; 0.304 by the face-on view's bosses (3239ad914a00: 106.5 px of 237.9). ± covers the three and the outline's own scale (the pin's hole taken as the pin's size)","via":"user"}}],"note":"The trigger is one plate: its body is as thick as its bow is wide within 1.5% in both end-on photos (84.2 px to the bow's 83.1 seen along its height; 106.5 to 105.0 with the face toward the lens). A mil-spec trigger's body is 0.29 (std.ar15.trigger_body_width)."},"boss_length":{"label":"The bosses round the pin hole, end to end (across the trigger)","kind":"length","measurements":[{"id":"user","value":0.68,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/larue-mbt-2s bd521c1c8184 (the user's own LTMBT-2S-SB and its hammer on a counter, each seen along its own height, a US quarter lying between; 2026-10-05)","scaleRef":"the trigger's own length in the same view, by its traced outline (profiles.side: 1.899 in, 547.5 px, 288 px/in); in the face-on view (3239ad914a00) the bow's own width (shoe_width)","method":"the bosses' two ends at row 1285 (columns 886.8 to 1079.1: 192.3 px): 0.667 by the outline's length. Face on they are 237.9 px to the bow's 105.0: 0.691 at the thread's 0.305, 0.668 at the photo's 0.295. The middle; ± covers the three. A pocket is .690: they are not wider","via":"user"}}],"note":"What centres the trigger between the pocket's walls (std.ar15.fcg_pocket_width, .690): the Army's own trigger's are .680 ± .003 (bcm-pnt-trigger.boss_length, drawing 8448592). LaRue's reads the same within the photos."},"boss_d":{"label":"The bosses round the pin hole, diameter","kind":"length","measurements":[{"id":"photo","value":0.285,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/larue-mbt-2s 45e00d2ce552 (LaRue MBT-2S-SB, straight side view on white, marked LTMBT-2S-SB; supplied in chat)","scaleRef":"the pivot hole in the same face, 46.4 px along the row through its centre and 45.8 down the column (the 0.154 in pin, larue-mbt-2s.pin_diameter: 303.8 px/in, the trace's scale)","method":"the dark ring round the hole, inside the spring's coil: 84 to 88 px across along the row through the hole's centre (columns 377.2 to 461.4 or 465.3), the coil's wire 115 px from centre to centre round it. ± is 6 px","via":"user"}}],"note":"Read inside the trigger spring's coil, which sits round the boss: the coil's wire and its shadow hide the boss's own edge by a few pixels either way. The Army's trigger's is .322 -.015 (std.ar15.trigger_boss_d)."},"shoe_chamfer":{"label":"The bow's face: the chamfer down each of its sides, across","kind":"length","measurements":[{"id":"user","value":0.03,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/larue-mbt-2s 0e58651de32a (the user's own LTMBT-2S-SB held over a counter, the bow's face toward the lens; 2026-10-05)","scaleRef":"the bow's own width in the same view and plane (shoe_width): 173 px from side to side at row 1700","method":"the dark band down each side of the lit face, rows 1700 and 1740: 15 to 20 px of the bow's 173 (the face itself 137 px): 0.027 to 0.035 in. ± is 5 px","via":"user"}}],"note":"The thread: 'flat with a small chamfer along the sides to break the edges'; Everyday Marksman: 'sharply-angled corners on the shoe'. Its angle isn't read (drawn at 45 degrees)."},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"aggregator","value":2.9,"unit":"oz","stated":"2.9 oz","source":{"type":"spec","publisher":"retailer","name":"Rifle Configurator (aggregator; provenance unstated)","url":"https://www.rifleconfigurator.com/catalog/triggers/larue-mbt2s-trigger","retrieved":"2026-09-30","via":"harvest"}}]}}},{"subject":"law-tactical-gen-s-folder","title":"Law Tactical AR Folding Stock Adapter GEN-S","dimensions":{"weight":{"label":"Weight (the housing with its flange, and the bolt carrier extension)","kind":"mass","measurements":[{"id":"sum","value":9.4,"unit":"oz","pm":0.1,"source":{"type":"derived","expr":"{.housing_weight} + {.extension_weight}","via":"harvest"}},{"id":"rc","value":9.4,"unit":"oz","pm":0.05,"stated":"Adds 9.4 oz and 1.3 in.","source":{"type":"spec","publisher":"review","name":"rifleconfigurator.com, Best Folding Stock Adapters (a buyer's guide; #1 Law Tactical AR Folding Stock Adapter GEN-S)","url":"https://www.rifleconfigurator.com/guides/best-folding-stock-adapters","retrieved":"2026-10-18","via":"harvest"}},{"id":"ar15d","value":8.496,"unit":"oz","pm":0.0005,"stated":"Weight 8.496 oz Dimensions 4 × 2.2 × 2.2 in MPN 99329GEN-S","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, Law Tactical AR Folding Stock Adapter Gen S - Black - OEM - 99329GEN-S","url":"https://ar15discounts.com/products/law-tactical-ar-folding-stock-adapter-gen-s-black-oem/","retrieved":"2026-10-18","via":"harvest"},"note":"A shop's weight field: neither the housing (7.4) nor the housing and extension (9.4) the maker's page that the same shop quotes gives."}],"adopt":{"from":"sum","reason":"The maker's two figures, housing and extension; a review gives the same 9.4 oz. The shop's field matches neither of the maker's and doesn't say what it weighed."},"note":"What the box holds that goes on the rifle: the hinge assembly and its threaded flange (the maker's \"Housing Weight\"; that the flange is in it is an assumption, no page says) and the bolt carrier extension, which it weighs apart. The flange tool and the sheet aren't counted. rifleconfigurator's 9.4 oz is the same sum. AR15Discounts' \"Weight 8.496 oz\" is a shop field beside a \"Dimensions 4 × 2.2 × 2.2 in\" that doesn't say what it measures: kept beside the sum, not adopted."},"housing_weight":{"label":"Housing weight (the hinge assembly)","kind":"mass","measurements":[{"id":"law","value":7.4,"unit":"oz","pm":0.05,"stated":"GEN-S SPECIFICATIONS Housing Weight: 7.4 oz Bolt Carrier Extension: 2 oz Adds 1.3 inches to length of pull CNC Machined 17-4 Steel","source":{"type":"spec","publisher":"manufacturer","name":"Law Tactical, AR Folding Stock Adapter GEN-S (the page at the Gen 3-M's address: \"PRODUCT CODE: 99312\"), GEN-S SPECIFICATIONS","url":"https://www.lawtactical.com/ar_folding_stock_adapter_gen_3_m_p/99312.htm","retrieved":"2026-10-18","via":"harvest"}},{"id":"sheet","value":7.4,"unit":"oz","pm":0.05,"stated":"GEN-S SPECIFICATIONS Housing Weight: 7.4 oz Bolt Carrier Extension: 2oz Adds 1.3 inches to Length of Pull 17-4 Stainless Steel Housing","source":{"type":"spec","publisher":"manufacturer","name":"Law Tactical, AR Folding Stock Adapter GEN-S data sheet (linked from the maker's page as its Data Sheet; one page with no text layer, read as a picture; the same sheet as GEN3S-web-one-sheet.jpg), GEN-S SPECIFICATIONS","url":"https://www.arfoldingstock.com/img/GEN3S-web-instructions.pdf","retrieved":"2026-10-18","via":"harvest"}},{"id":"wilson","value":7.4,"unit":"oz","pm":0.05,"stated":"Housing Weight: 7.4 oz Bolt Carrier Extension: 2 oz Adds 1.3 inches to length of pull CNC machined 17-4 Steel","source":{"type":"spec","publisher":"retailer","name":"Wilson Combat, STOCK ADAPTOR, LAW TACTICAL, AR, GEN-S, FOLDING (item NW809), Feautures","url":"https://wilsoncombat.com/stock-adapter-law-tactical-ar-gen-s-m-folding.html","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"law","reason":"The maker's page; its data sheet and a seller quoting it give the same."}},"extension_weight":{"label":"Bolt carrier extension weight","kind":"mass","measurements":[{"id":"law","value":2,"unit":"oz","pm":0.5,"stated":"Bolt Carrier Extension: 2 oz","source":{"type":"spec","publisher":"manufacturer","name":"Law Tactical, AR Folding Stock Adapter GEN-S (the page at the Gen 3-M's address: \"PRODUCT CODE: 99312\"), GEN-S SPECIFICATIONS","url":"https://www.lawtactical.com/ar_folding_stock_adapter_gen_3_m_p/99312.htm","retrieved":"2026-10-18","via":"harvest"}},{"id":"sheet","value":2,"unit":"oz","pm":0.5,"stated":"Bolt Carrier Extension: 2oz","source":{"type":"spec","publisher":"manufacturer","name":"Law Tactical, AR Folding Stock Adapter GEN-S data sheet (linked from the maker's page as its Data Sheet; one page with no text layer, read as a picture; the same sheet as GEN3S-web-one-sheet.jpg), GEN-S SPECIFICATIONS","url":"https://www.arfoldingstock.com/img/GEN3S-web-instructions.pdf","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"law","reason":"The maker's page; its data sheet gives the same."}},"added_length":{"label":"How far it moves the receiver extension back","kind":"length","measurements":[{"id":"law","value":1.3,"unit":"in","pm":0.05,"stated":"Adds 1.3 inches to length of pull","source":{"type":"spec","publisher":"manufacturer","name":"Law Tactical, AR Folding Stock Adapter GEN-S (the page at the Gen 3-M's address: \"PRODUCT CODE: 99312\"), GEN-S SPECIFICATIONS","url":"https://www.lawtactical.com/ar_folding_stock_adapter_gen_3_m_p/99312.htm","retrieved":"2026-10-18","via":"harvest"}},{"id":"sheet","value":1.3,"unit":"in","pm":0.05,"stated":"Adds 1.3 inches to Length of Pull","source":{"type":"spec","publisher":"manufacturer","name":"Law Tactical, AR Folding Stock Adapter GEN-S data sheet (linked from the maker's page as its Data Sheet; one page with no text layer, read as a picture; the same sheet as GEN3S-web-one-sheet.jpg), GEN-S SPECIFICATIONS","url":"https://www.arfoldingstock.com/img/GEN3S-web-instructions.pdf","retrieved":"2026-10-18","via":"harvest"}},{"id":"wilson","value":1.3,"unit":"in","pm":0.05,"stated":"Adds 1.3 inches to length of pull","source":{"type":"spec","publisher":"retailer","name":"Wilson Combat, STOCK ADAPTOR, LAW TACTICAL, AR, GEN-S, FOLDING (item NW809), Feautures","url":"https://wilsoncombat.com/stock-adapter-law-tactical-ar-gen-s-m-folding.html","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"law","reason":"The maker's page; its data sheet and a seller give the same. The length of pull is what the stock moves back by, which is this."},"note":"The tube screws into the stock half as into a lower (the instructions: \"in the same manner it would be installed onto the rear of the rifle receiver\"), so the stock half's rear face is the receiver's rear face moved back by this. No side photo with a lower's pins in frame is on file to check it."},"length":{"label":"Its length along the bore (the housing, front face to rear face)","kind":"length","measurements":[{"id":"added","value":1.3,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{.added_length}","via":"harvest"}}],"note":"The receiver half's front face bears on the lower's rear face (std.ar15.receiver_rear_x) and the stock half's rear face stands where a lower's would: the housing is as long as it moves the tube back. The threaded flange reaches forward of it into the lower's ring."},"receiver_half_length":{"label":"The receiver half, front face to where the halves meet","kind":"length","measurements":[{"id":"seam","value":0.65,"unit":"in","pm":0.1,"source":{"type":"derived","expr":"{.hinge_x} + {std.ar15.receiver_rear_x}","via":"harvest"}}],"note":"Where the halves meet is in the hinge's plane (.hinge_x): folded open 180 degrees the two mating faces lie side by side in one plane (Primary Arms' 430116178_01 from above), which a seam ahead of or behind the axis would offset by twice its distance. No square side view of the part is on file to read it on directly."},"stock_half_length":{"label":"The stock half, where the halves meet to its rear face","kind":"length","measurements":[{"id":"rest","value":0.65,"unit":"in","pm":0.1,"source":{"type":"derived","expr":"{.length} - {.receiver_half_length}","via":"harvest"}}]},"hinge_x":{"label":"The hinge's axis behind the takedown pin","kind":"length","measurements":[{"id":"photo","value":1.775,"unit":"in","pm":0.1,"source":{"type":"derived","expr":"0in - {std.ar15.receiver_rear_x} + {.length} / 2","via":"harvest"}}],"note":"Half the housing's length behind the lower's rear face (the Army's drawing): on Primary Arms' photo from above (430116178_01) the part lies folded open 180 degrees, each half flat on its outer face (the receiver half's front, the stock half's rear: both bores read as circles, rms under a pixel), with the hinge's axis level between them, which puts the axis as far from the one outer face as from the other."},"hinge_z":{"label":"The hinge's axis out from the tube's axis, toward the side it folds to (the rifle's left)","kind":"length","measurements":[{"id":"pa01","value":1.082,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: the black GEN-S folded open 180 degrees on white, both mating faces up, from straight above; 5000 x 5000)","scaleRef":"the stock half's threaded bore seen through: a RANSAC circle on the hole's rim, 824.2 px across (rms 0.82 px), as .bore_thread_crest_d: 712.5 px/in. The photo is rolled 2.28 degrees (the receiver half's bore, 859.8 px across, stands 61 px higher 1540 px to the right): read after turning it back so the two bores' centres lie on one row","method":"half the bores' centres' distance, 1541.4 px / 2 = 770.7 px. The hinge's column's own edges against the white beside it (the middle knuckle's left edge, the knurled nut's two) put its middle 9 px right and 10 px left of midway. ± covers the scale's (2.1%) and those pixels","via":"harvest"}}],"note":"Folded open 180 degrees about the hinge, the two halves' bores stand side by side twice this apart, with the hinge midway. The side is the left: in Primary Arms' photo the mating faces are toward the lens (as they face rearward when folded) and the receiver half (its latch, its window and \"CLOSE BEFORE FIRING\") is on the right, its button's bar out of its right side: seen from behind, the stock half has swung to the rifle's left. The instructions' cover draws a braced rifle from its left (the muzzle to the left) with the brace folded across the near side, the data sheet's drawing the same."},"fold_max":{"label":"How far the hinge turns before its own halves stop it","kind":"angle","measurements":[{"id":"photo","value":180,"unit":"deg","pm":5,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: the black GEN-S folded open 180 degrees on white, both mating faces up, from straight above; 5000 x 5000)","scaleRef":"angles: both bores read as circles (RANSAC, rms 0.82 and 0.54 px) on one row once the picture's roll is taken out, the faces square to the lens","method":"the two halves' faces in one plane, side by side; read with US 8,769,855 (engraved \"PAT. 8769855\" on the part): \"the stock can be folded flat against the receiver when the folding stock adapter is in an open position\"","via":"harvest"}}],"note":"Folded open on a table (Primary Arms' photo from above) the halves lie side by side with their mating faces in one plane, and below the rings the two halves meet across the hinge: the patent the part is marked with says the stock \"can be folded flat against the receiver\". No page states an angle, and no photo shows it turned past that; how far the stock itself goes on a rifle before it meets the receiver is the build's (the app works it out)."},"bore_thread_crest_d":{"label":"The stock half's threaded bore: its thread's crests (what one sees through it)","kind":"length","measurements":[{"id":"thread","value":1.1568,"unit":"in","pm":0.0245,"source":{"type":"derived","expr":"({std.receiver_extension.thread_major_d} / 1.0432 + {std.receiver_extension.thread_major_d}) / 2","via":"harvest"},"note":"The middle of 1.1324 (the flange's major diameter over this part's two bores' ratio) and 1.1813 (the extension's major diameter, which a hole's crests are under); ± half that span."}],"note":"The scale of every photo here. The receiver extension screws in as into a lower, so this is a 1 3/16-16 thread in a hole: its crests lie between the extension's own minor and major diameters. The receiver half's bore, read beside it in the same photo at 1.0432 times this (859.8 / 824.2 px), has to pass the threaded flange (std major 1.1813): that puts this at 1.1324 or more."},"receiver_bore_d":{"label":"The receiver half's bore (where the flange passes, at its narrowest)","kind":"length","measurements":[{"id":"pa01","value":1.207,"unit":"in","pm":0.026,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: the black GEN-S folded open 180 degrees on white, both mating faces up, from straight above; 5000 x 5000)","scaleRef":"the stock half's threaded bore seen through: a RANSAC circle on the hole's rim, 824.2 px across (rms 0.82 px), as .bore_thread_crest_d: 712.5 px/in. The photo is rolled 2.28 degrees (the receiver half's bore, 859.8 px across, stands 61 px higher 1540 px to the right): read after turning it back so the two bores' centres lie on one row","method":"a RANSAC circle on the hole's rim, 859.8 px across (rms 0.54 px; the latch's hook inside it left out by the fit's tolerance)","via":"harvest"}}]},"body_top_above_axis":{"label":"The rings' tops above the tube's axis","kind":"length","measurements":[{"id":"pa01","value":0.706,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: the black GEN-S folded open 180 degrees on white, both mating faces up, from straight above; 5000 x 5000)","scaleRef":"the stock half's threaded bore seen through: a RANSAC circle on the hole's rim, 824.2 px across (rms 0.82 px), as .bore_thread_crest_d: 712.5 px/in. The photo is rolled 2.28 degrees (the receiver half's bore, 859.8 px across, stands 61 px higher 1540 px to the right): read after turning it back so the two bores' centres lie on one row","method":"the stock half's outline's top, 503 px above its bore's centre (the receiver half's reads 0.687: its ring is a little lower)","via":"harvest"}}]},"body_bottom_below_axis":{"label":"Its lowest point below the tube's axis (the receiver half's foot)","kind":"length","measurements":[{"id":"pa01","value":1.52,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: the black GEN-S folded open 180 degrees on white, both mating faces up, from straight above; 5000 x 5000)","scaleRef":"the stock half's threaded bore seen through: a RANSAC circle on the hole's rim, 824.2 px across (rms 0.82 px), as .bore_thread_crest_d: 712.5 px/in. The photo is rolled 2.28 degrees (the receiver half's bore, 859.8 px across, stands 61 px higher 1540 px to the right): read after turning it back so the two bores' centres lie on one row","method":"the receiver half's outline's lowest row, 1083 px below the bores' row (the stock half's foot reads 1.433)","via":"harvest"}}]},"height":{"label":"Its height","kind":"length","measurements":[{"id":"sum","value":2.226,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.body_top_above_axis} + {.body_bottom_below_axis}","via":"harvest"}}]},"far_side":{"label":"Its side away from the hinge (the rifle's right), out from the tube's axis","kind":"length","measurements":[{"id":"pa01","value":0.804,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: the black GEN-S folded open 180 degrees on white, both mating faces up, from straight above; 5000 x 5000)","scaleRef":"the stock half's threaded bore seen through: a RANSAC circle on the hole's rim, 824.2 px across (rms 0.82 px), as .bore_thread_crest_d: 712.5 px/in. The photo is rolled 2.28 degrees (the receiver half's bore, 859.8 px across, stands 61 px higher 1540 px to the right): read after turning it back so the two bores' centres lie on one row","method":"the stock half's ring at its widest, 573 px from its bore's centre (the receiver half's ring 0.794; its straight side lower down 0.751, where the button's bar stands out past it)","via":"harvest"}}]},"button_side":{"label":"The receiver half's straight side where the button's bar comes out, out from the tube's axis","kind":"length","measurements":[{"id":"pa01","value":0.751,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: the black GEN-S folded open 180 degrees on white, both mating faces up, from straight above; 5000 x 5000)","scaleRef":"the stock half's threaded bore seen through: a RANSAC circle on the hole's rim, 824.2 px across (rms 0.82 px), as .bore_thread_crest_d: 712.5 px/in. The photo is rolled 2.28 degrees (the receiver half's bore, 859.8 px across, stands 61 px higher 1540 px to the right): read after turning it back so the two bores' centres lie on one row","method":"column 3676, 535 px from the receiver half's bore centre: the side runs straight there from 0.37 to 1.06 under the axis (columns 3672 to 3676), the bar standing out past it between rows 1730 and 1928","via":"harvest"}}]},"width":{"label":"Its width across the rifle, the hinge included (the button's bar not)","kind":"length","measurements":[{"id":"sum","value":2.181,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{.far_side} + {.hinge_z} + {.pivot_d} / 2","via":"harvest"}}]},"knuckle_d":{"label":"The hinge's two outer knuckles (the stock half's tabs), across","kind":"length","measurements":[{"id":"pa01","value":0.44,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: the black GEN-S folded open 180 degrees on white, both mating faces up, from straight above; 5000 x 5000)","scaleRef":"the stock half's threaded bore seen through: a RANSAC circle on the hole's rim, 824.2 px across (rms 0.82 px), as .bore_thread_crest_d: 712.5 px/in. The photo is rolled 2.28 degrees (the receiver half's bore, 859.8 px across, stands 61 px higher 1540 px to the right): read after turning it back so the two bores' centres lie on one row","method":"the upper tab seen from the side between its two lit edges, 313 px (its side toward the stock half meets that half's body in one tone, so where it ends there is a reading of its highlight's edge)","via":"harvest"}}]},"pivot_d":{"label":"The hinge's middle knuckle (the receiver half's pivot), across","kind":"length","measurements":[{"id":"pa01","value":0.6,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: the black GEN-S folded open 180 degrees on white, both mating faces up, from straight above; 5000 x 5000)","scaleRef":"the stock half's threaded bore seen through: a RANSAC circle on the hole's rim, 824.2 px across (rms 0.82 px), as .bore_thread_crest_d: 712.5 px/in. The photo is rolled 2.28 degrees (the receiver half's bore, 859.8 px across, stands 61 px higher 1540 px to the right): read after turning it back so the two bores' centres lie on one row","method":"seen from the side, 428 px across (its left edge against the white slot beside it, column 2165; its right edge where it meets the receiver half's face, 2593)","via":"harvest"}}]},"washer_d":{"label":"The black washers between the knuckles, across","kind":"length","measurements":[{"id":"pa01","value":0.57,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: the black GEN-S folded open 180 degrees on white, both mating faces up, from straight above; 5000 x 5000)","scaleRef":"the stock half's threaded bore seen through: a RANSAC circle on the hole's rim, 824.2 px across (rms 0.82 px), as .bore_thread_crest_d: 712.5 px/in. The photo is rolled 2.28 degrees (the receiver half's bore, 859.8 px across, stands 61 px higher 1540 px to the right): read after turning it back so the two bores' centres lie on one row","method":"405 to 410 px (the upper washer's black from the white slot, column 2190, to where the receiver half's grey begins, 2595; the lower 2185 to 2595)","via":"harvest"}}]},"upper_tab_top":{"label":"The upper tab's top, below the tube's axis","kind":"length","measurements":[{"id":"pa01","value":0.161,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: the black GEN-S folded open 180 degrees on white, both mating faces up, from straight above; 5000 x 5000)","scaleRef":"the stock half's threaded bore seen through: a RANSAC circle on the hole's rim, 824.2 px across (rms 0.82 px), as .bore_thread_crest_d: 712.5 px/in. The photo is rolled 2.28 degrees (the receiver half's bore, 859.8 px across, stands 61 px higher 1540 px to the right): read after turning it back so the two bores' centres lie on one row","method":"along the hinge's column (columns 2330 to 2470): the silhouette begins at row 1284, its chamfer's lighter band to 1300","via":"harvest"}}]},"upper_tab_bottom":{"label":"The upper tab's bottom, below the tube's axis","kind":"length","measurements":[{"id":"pa01","value":0.434,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: the black GEN-S folded open 180 degrees on white, both mating faces up, from straight above; 5000 x 5000)","scaleRef":"the stock half's threaded bore seen through: a RANSAC circle on the hole's rim, 824.2 px across (rms 0.82 px), as .bore_thread_crest_d: 712.5 px/in. The photo is rolled 2.28 degrees (the receiver half's bore, 859.8 px across, stands 61 px higher 1540 px to the right): read after turning it back so the two bores' centres lie on one row","method":"row 1478, where the black washer begins (the column's median tone falls from 46 to 30)","via":"harvest"}}]},"pivot_top":{"label":"The middle knuckle's top, below the tube's axis","kind":"length","measurements":[{"id":"pa01","value":0.556,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: the black GEN-S folded open 180 degrees on white, both mating faces up, from straight above; 5000 x 5000)","scaleRef":"the stock half's threaded bore seen through: a RANSAC circle on the hole's rim, 824.2 px across (rms 0.82 px), as .bore_thread_crest_d: 712.5 px/in. The photo is rolled 2.28 degrees (the receiver half's bore, 859.8 px across, stands 61 px higher 1540 px to the right): read after turning it back so the two bores' centres lie on one row","method":"row 1565 (the tone rises from 30 to 100)","via":"harvest"}}]},"pivot_bottom":{"label":"The middle knuckle's bottom, below the tube's axis","kind":"length","measurements":[{"id":"pa01","value":0.987,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: the black GEN-S folded open 180 degrees on white, both mating faces up, from straight above; 5000 x 5000)","scaleRef":"the stock half's threaded bore seen through: a RANSAC circle on the hole's rim, 824.2 px across (rms 0.82 px), as .bore_thread_crest_d: 712.5 px/in. The photo is rolled 2.28 degrees (the receiver half's bore, 859.8 px across, stands 61 px higher 1540 px to the right): read after turning it back so the two bores' centres lie on one row","method":"row 1872 (the tone falls from 70 to 26)","via":"harvest"}}]},"lower_tab_top":{"label":"The lower tab's top, below the tube's axis","kind":"length","measurements":[{"id":"pa01","value":1.107,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: the black GEN-S folded open 180 degrees on white, both mating faces up, from straight above; 5000 x 5000)","scaleRef":"the stock half's threaded bore seen through: a RANSAC circle on the hole's rim, 824.2 px across (rms 0.82 px), as .bore_thread_crest_d: 712.5 px/in. The photo is rolled 2.28 degrees (the receiver half's bore, 859.8 px across, stands 61 px higher 1540 px to the right): read after turning it back so the two bores' centres lie on one row","method":"row 1958","via":"harvest"}}]},"lower_tab_bottom":{"label":"The lower tab's bottom, below the tube's axis","kind":"length","measurements":[{"id":"pa01","value":1.294,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: the black GEN-S folded open 180 degrees on white, both mating faces up, from straight above; 5000 x 5000)","scaleRef":"the stock half's threaded bore seen through: a RANSAC circle on the hole's rim, 824.2 px across (rms 0.82 px), as .bore_thread_crest_d: 712.5 px/in. The photo is rolled 2.28 degrees (the receiver half's bore, 859.8 px across, stands 61 px higher 1540 px to the right): read after turning it back so the two bores' centres lie on one row","method":"row 2091, where the knurled nut begins (the silhouette narrows to the nut's 263 px)","via":"harvest"}}]},"nut_d":{"label":"The hinge bolt's knurled nut, across","kind":"length","measurements":[{"id":"pa01","value":0.369,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: the black GEN-S folded open 180 degrees on white, both mating faces up, from straight above; 5000 x 5000)","scaleRef":"the stock half's threaded bore seen through: a RANSAC circle on the hole's rim, 824.2 px across (rms 0.82 px), as .bore_thread_crest_d: 712.5 px/in. The photo is rolled 2.28 degrees (the receiver half's bore, 859.8 px across, stands 61 px higher 1540 px to the right): read after turning it back so the two bores' centres lie on one row","method":"263 px (columns 2229 to 2492, both edges against the white)","via":"harvest"}}]},"nut_bottom":{"label":"The knurled nut's end, below the tube's axis","kind":"length","measurements":[{"id":"pa01","value":1.476,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: the black GEN-S folded open 180 degrees on white, both mating faces up, from straight above; 5000 x 5000)","scaleRef":"the stock half's threaded bore seen through: a RANSAC circle on the hole's rim, 824.2 px across (rms 0.82 px), as .bore_thread_crest_d: 712.5 px/in. The photo is rolled 2.28 degrees (the receiver half's bore, 859.8 px across, stands 61 px higher 1540 px to the right): read after turning it back so the two bores' centres lie on one row","method":"row 2221, the knurl's end","via":"harvest"}}]},"stock_hole_small_d":{"label":"The stock half's rear face: its two small holes, across","kind":"length","measurements":[{"id":"pa03","value":0.293,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder 414ca4a71262 (Primary Arms 430116178_03: the black GEN-S opened about 180 degrees, from behind the stock half's rear face, a little to the side and above; 5000 x 5000)","scaleRef":"the threaded bore's diameter along the face's unforeshortened direction, 776.5 px as .bore_thread_crest_d (the white seen through the bore, an ellipse fitted to it); across that the face is foreshortened by 0.78, the ratio of each small hole's ellipse's axes (156 by 196, 150 by 197 px), and is read after dividing by it; heights from the bore's lowest rim (its crest radius below the axis)","method":"each hole's dark (under 30 of 255) an ellipse, 196.2 and 197.4 px along its long axis","via":"harvest"}}]},"stock_hole_small_apart":{"label":"The two small holes, each out from the middle","kind":"length","measurements":[{"id":"pa03","value":0.366,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder 414ca4a71262 (Primary Arms 430116178_03: the black GEN-S opened about 180 degrees, from behind the stock half's rear face, a little to the side and above; 5000 x 5000)","scaleRef":"the threaded bore's diameter along the face's unforeshortened direction, 776.5 px as .bore_thread_crest_d (the white seen through the bore, an ellipse fitted to it); across that the face is foreshortened by 0.78, the ratio of each small hole's ellipse's axes (156 by 196, 150 by 197 px), and is read after dividing by it; heights from the bore's lowest rim (its crest radius below the axis)","method":"the two centres (3326.2, 2830.8) and (3739.6, 2785.5) after the face's foreshortening is taken out, half their distance","via":"harvest"}}]},"stock_hole_small_below_axis":{"label":"The two small holes' centres below the tube's axis","kind":"length","measurements":[{"id":"pa03","value":0.685,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder 414ca4a71262 (Primary Arms 430116178_03: the black GEN-S opened about 180 degrees, from behind the stock half's rear face, a little to the side and above; 5000 x 5000)","scaleRef":"the threaded bore's diameter along the face's unforeshortened direction, 776.5 px as .bore_thread_crest_d (the white seen through the bore, an ellipse fitted to it); across that the face is foreshortened by 0.78, the ratio of each small hole's ellipse's axes (156 by 196, 150 by 197 px), and is read after dividing by it; heights from the bore's lowest rim (its crest radius below the axis)","method":"their line 68 px (0.107 in at 633 px/in up and down the face) below the bore's lowest rim, which is the crest's radius below the axis","via":"harvest"}}]},"stock_hole_big_d":{"label":"The stock half's rear face: its large hole (the sling's quick-detach socket), across","kind":"length","measurements":[{"id":"pa03","value":0.5,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder 414ca4a71262 (Primary Arms 430116178_03: the black GEN-S opened about 180 degrees, from behind the stock half's rear face, a little to the side and above; 5000 x 5000)","scaleRef":"the threaded bore's diameter along the face's unforeshortened direction, 776.5 px as .bore_thread_crest_d (the white seen through the bore, an ellipse fitted to it); across that the face is foreshortened by 0.78, the ratio of each small hole's ellipse's axes (156 by 196, 150 by 197 px), and is read after dividing by it; heights from the bore's lowest rim (its crest radius below the axis)","method":"the hole's dark an ellipse, 330.7 px (under 22 of 255) to 347.5 px (under 30) along its long axis","via":"harvest"}}],"note":"The maker's page: \"An integrated single point sling attachment point is included\" and \"QUICK DETACH Sling attachment point\": the large blind hole under the bore, with a floor and a ring in it, is that socket."},"stock_hole_big_below_axis":{"label":"The large hole's centre below the tube's axis","kind":"length","measurements":[{"id":"pa03","value":1.06,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder 414ca4a71262 (Primary Arms 430116178_03: the black GEN-S opened about 180 degrees, from behind the stock half's rear face, a little to the side and above; 5000 x 5000)","scaleRef":"the threaded bore's diameter along the face's unforeshortened direction, 776.5 px as .bore_thread_crest_d (the white seen through the bore, an ellipse fitted to it); across that the face is foreshortened by 0.78, the ratio of each small hole's ellipse's axes (156 by 196, 150 by 197 px), and is read after dividing by it; heights from the bore's lowest rim (its crest radius below the axis)","method":"254 px below the small holes' line (0.40 in at 633 px/in), added to .stock_hole_small_below_axis's reading; the eye has the hole's top rim 0.08 higher than the fit's","via":"harvest"}}]},"stock_hole_depth":{"label":"How deep the rear face's two small holes go","kind":"length","measurements":[{"id":"assumed","value":0.35,"unit":"in","pm":0.15,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the holes are dark to their floors in Primary Arms' photo of the rear face, and the stock half's front face has none (they are blind). Taken a little over half the half's length.","via":"harvest"}}]},"qd_depth":{"label":"How deep the sling socket goes","kind":"length","measurements":[{"id":"assumed","value":0.45,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: Primary Arms' photo of the rear face shows the socket's floor and a ring in it, well down; how far isn't read. Short of the half's length, its front face having no hole there.","via":"harvest"}}]},"tab_width":{"label":"The stock half's locking lug, across (on its front face, low on the side away from the hinge)","kind":"length","measurements":[{"id":"pa01","value":0.21,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: the black GEN-S folded open 180 degrees on white, both mating faces up, from straight above; 5000 x 5000)","scaleRef":"the stock half's threaded bore seen through: a RANSAC circle on the hole's rim, 824.2 px across (rms 0.82 px), as .bore_thread_crest_d: 712.5 px/in. The photo is rolled 2.28 degrees (the receiver half's bore, 859.8 px across, stands 61 px higher 1540 px to the right): read after turning it back so the two bores' centres lie on one row","method":"the raised rounded pad left of \"PAT. 8769855\", its lit rim, 150 px across","via":"harvest"}}]},"tab_height":{"label":"The locking lug, up and down","kind":"length","measurements":[{"id":"pa01","value":0.557,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: the black GEN-S folded open 180 degrees on white, both mating faces up, from straight above; 5000 x 5000)","scaleRef":"the stock half's threaded bore seen through: a RANSAC circle on the hole's rim, 824.2 px across (rms 0.82 px), as .bore_thread_crest_d: 712.5 px/in. The photo is rolled 2.28 degrees (the receiver half's bore, 859.8 px across, stands 61 px higher 1540 px to the right): read after turning it back so the two bores' centres lie on one row","method":"397 px, its two rounded ends' rims","via":"harvest"}}]},"tab_centre_out":{"label":"The locking lug's middle, out from the tube's axis toward the side away from the hinge","kind":"length","measurements":[{"id":"pa01","value":0.299,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: the black GEN-S folded open 180 degrees on white, both mating faces up, from straight above; 5000 x 5000)","scaleRef":"the stock half's threaded bore seen through: a RANSAC circle on the hole's rim, 824.2 px across (rms 0.82 px), as .bore_thread_crest_d: 712.5 px/in. The photo is rolled 2.28 degrees (the receiver half's bore, 859.8 px across, stands 61 px higher 1540 px to the right): read after turning it back so the two bores' centres lie on one row","method":"column 1387, 212.7 px from the stock half's bore centre","via":"harvest"}}]},"tab_centre_below_axis":{"label":"The locking lug's middle below the tube's axis","kind":"length","measurements":[{"id":"pa01","value":0.946,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: the black GEN-S folded open 180 degrees on white, both mating faces up, from straight above; 5000 x 5000)","scaleRef":"the stock half's threaded bore seen through: a RANSAC circle on the hole's rim, 824.2 px across (rms 0.82 px), as .bore_thread_crest_d: 712.5 px/in. The photo is rolled 2.28 degrees (the receiver half's bore, 859.8 px across, stands 61 px higher 1540 px to the right): read after turning it back so the two bores' centres lie on one row","method":"row 1843","via":"harvest"}}]},"tab_proud":{"label":"How far the locking lug stands forward of the stock half's face","kind":"length","measurements":[{"id":"assumed","value":0.12,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows the lug in profile (Primary Arms' three-quarter view has it standing a little off the face). The patent's tab goes into the receiver half's indentation, where the button's latch catches it.","via":"harvest"}}]},"window_width":{"label":"The receiver half's window for the locking lug and the latch, across","kind":"length","measurements":[{"id":"pa01","value":0.42,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: the black GEN-S folded open 180 degrees on white, both mating faces up, from straight above; 5000 x 5000)","scaleRef":"the stock half's threaded bore seen through: a RANSAC circle on the hole's rim, 824.2 px across (rms 0.82 px), as .bore_thread_crest_d: 712.5 px/in. The photo is rolled 2.28 degrees (the receiver half's bore, 859.8 px across, stands 61 px higher 1540 px to the right): read after turning it back so the two bores' centres lie on one row","method":"the dark opening right of \"CLOSE BEFORE FIRING\", 300 px at mid-height (its side toward the button leans in, 320 px at its top, 260 at its bottom)","via":"harvest"}}]},"window_width_top":{"label":"The window across at its top (its side toward the button leans in)","kind":"length","measurements":[{"id":"pa01","value":0.449,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: the black GEN-S folded open 180 degrees on white, both mating faces up, from straight above; 5000 x 5000)","scaleRef":"the stock half's threaded bore seen through: a RANSAC circle on the hole's rim, 824.2 px across (rms 0.82 px), as .bore_thread_crest_d: 712.5 px/in. The photo is rolled 2.28 degrees (the receiver half's bore, 859.8 px across, stands 61 px higher 1540 px to the right): read after turning it back so the two bores' centres lie on one row","method":"320 px (columns 3235 to 3555 at row 1700): its side toward the hinge upright, its side toward the button leaning in","via":"harvest"}}]},"window_width_bottom":{"label":"The window across at its bottom","kind":"length","measurements":[{"id":"pa01","value":0.365,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: the black GEN-S folded open 180 degrees on white, both mating faces up, from straight above; 5000 x 5000)","scaleRef":"the stock half's threaded bore seen through: a RANSAC circle on the hole's rim, 824.2 px across (rms 0.82 px), as .bore_thread_crest_d: 712.5 px/in. The photo is rolled 2.28 degrees (the receiver half's bore, 859.8 px across, stands 61 px higher 1540 px to the right): read after turning it back so the two bores' centres lie on one row","method":"260 px (columns 3235 to 3495 at row 2020)","via":"harvest"}}]},"window_height":{"label":"The window, up and down","kind":"length","measurements":[{"id":"pa01","value":0.564,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: the black GEN-S folded open 180 degrees on white, both mating faces up, from straight above; 5000 x 5000)","scaleRef":"the stock half's threaded bore seen through: a RANSAC circle on the hole's rim, 824.2 px across (rms 0.82 px), as .bore_thread_crest_d: 712.5 px/in. The photo is rolled 2.28 degrees (the receiver half's bore, 859.8 px across, stands 61 px higher 1540 px to the right): read after turning it back so the two bores' centres lie on one row","method":"rows 1660 to 2062 (402 px)","via":"harvest"}}]},"window_centre_out":{"label":"The window's middle, out from the tube's axis toward the side away from the hinge","kind":"length","measurements":[{"id":"pa01","value":0.342,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: the black GEN-S folded open 180 degrees on white, both mating faces up, from straight above; 5000 x 5000)","scaleRef":"the stock half's threaded bore seen through: a RANSAC circle on the hole's rim, 824.2 px across (rms 0.82 px), as .bore_thread_crest_d: 712.5 px/in. The photo is rolled 2.28 degrees (the receiver half's bore, 859.8 px across, stands 61 px higher 1540 px to the right): read after turning it back so the two bores' centres lie on one row","method":"column 3385, 244 px from the receiver half's bore centre","via":"harvest"}}]},"window_centre_below_axis":{"label":"The window's middle below the tube's axis","kind":"length","measurements":[{"id":"pa01","value":0.971,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: the black GEN-S folded open 180 degrees on white, both mating faces up, from straight above; 5000 x 5000)","scaleRef":"the stock half's threaded bore seen through: a RANSAC circle on the hole's rim, 824.2 px across (rms 0.82 px), as .bore_thread_crest_d: 712.5 px/in. The photo is rolled 2.28 degrees (the receiver half's bore, 859.8 px across, stands 61 px higher 1540 px to the right): read after turning it back so the two bores' centres lie on one row","method":"row 1861","via":"harvest"}}]},"window_depth":{"label":"How deep the window goes into the receiver half","kind":"length","measurements":[{"id":"assumed","value":0.3,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: deep enough for the lug (.tab_proud) and the latch behind it; Primary Arms' photo shows the latch's block in it, its floor not.","via":"harvest"}}]},"button_width":{"label":"The button's bar out of the receiver half's side (the rifle's right), up and down","kind":"length","measurements":[{"id":"pa01","value":0.278,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: the black GEN-S folded open 180 degrees on white, both mating faces up, from straight above; 5000 x 5000)","scaleRef":"the stock half's threaded bore seen through: a RANSAC circle on the hole's rim, 824.2 px across (rms 0.82 px), as .bore_thread_crest_d: 712.5 px/in. The photo is rolled 2.28 degrees (the receiver half's bore, 859.8 px across, stands 61 px higher 1540 px to the right): read after turning it back so the two bores' centres lie on one row","method":"the black bar standing out past the side, rows 1730 to 1928 (198 px)","via":"harvest"}}]},"button_proud":{"label":"How far the button's bar stands out of the side","kind":"length","measurements":[{"id":"pa01","value":0.205,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: the black GEN-S folded open 180 degrees on white, both mating faces up, from straight above; 5000 x 5000)","scaleRef":"the stock half's threaded bore seen through: a RANSAC circle on the hole's rim, 824.2 px across (rms 0.82 px), as .bore_thread_crest_d: 712.5 px/in. The photo is rolled 2.28 degrees (the receiver half's bore, 859.8 px across, stands 61 px higher 1540 px to the right): read after turning it back so the two bores' centres lie on one row","method":"to column 3822, 146 px past the side's straight edge (3676)","via":"harvest"}}]},"button_below_axis":{"label":"The button's bar's middle below the tube's axis","kind":"length","measurements":[{"id":"pa01","value":0.926,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: the black GEN-S folded open 180 degrees on white, both mating faces up, from straight above; 5000 x 5000)","scaleRef":"the stock half's threaded bore seen through: a RANSAC circle on the hole's rim, 824.2 px across (rms 0.82 px), as .bore_thread_crest_d: 712.5 px/in. The photo is rolled 2.28 degrees (the receiver half's bore, 859.8 px across, stands 61 px higher 1540 px to the right): read after turning it back so the two bores' centres lie on one row","method":"row 1829","via":"harvest"}}]},"flange_head_d":{"label":"The threaded flange's head, across (it sits in the receiver half)","kind":"length","measurements":[{"id":"assumed","value":1.25,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the head bears on a lip inside the receiver half's bore (the patent: \"a head 114, which can be configured to abut up against a raised lip 146 located within the dead hinge section opening 123\"); a little over the lip, .receiver_bore_d. The flange's own pictures (Primary Arms' and Wilson Combat's) are each a picture of their own with no scale to the bore. Hidden when the adapter is on a rifle.","via":"harvest"}}]},"flange_head_length":{"label":"The flange's head, along the bore","kind":"length","measurements":[{"id":"assumed","value":0.12,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the flange's pictures have its slotted end a fraction of the ring's length; hidden on a rifle.","via":"harvest"}}]},"ext_pilot_d":{"label":"Bolt carrier extension: the end that goes into the carrier, across (its O-rings)","kind":"length","measurements":[{"id":"pa01","value":0.572,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: below the adapter, the bolt carrier extension standing on its head end, seen from in front and about 15 degrees above (its ends' rims are ellipses 0.25 and 0.27 of their widths: sin 15 degrees), a picture of its own set into the sheet; 5000 px)","scaleRef":"its length from the first shoulder's plane (row 3000) to its head end's plane (3780), 780 px, as .added_length: what it fills between the carrier and the buffer (the patent: \"This extension in length can compensate for the length added to the rifle by the addition of the folding stock adapter 100\"): 600 px/in along it, and 621 px/in across (its lengths are foreshortened by cos 15 degrees)","method":"its silhouette's width row by row (luminance under 200), its axis fitted through the rows' middles (0.38 degrees off upright); the pilot 355 px","via":"harvest"}}],"note":"The carrier's tail is bored .625 (std.ar15.carrier_tail_bore), and this end goes in to its first shoulder with O-rings that hold it: read at this scale it is 0.053 under the bore. Scaled instead so this end is the bore, the extension would stand 1.48 in behind its shoulder and weigh 2.9 oz in steel; at this scale its turned volume is 0.420 cubic inches, 1.92 oz, which is the maker's 2 oz. The length is taken as the scale; the O-rings' squeeze is what the 0.053 leaves."},"ext_pilot_length":{"label":"Bolt carrier extension: the end in the carrier, to its first shoulder","kind":"length","measurements":[{"id":"pa01","value":0.453,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: below the adapter, the bolt carrier extension standing on its head end, seen from in front and about 15 degrees above (its ends' rims are ellipses 0.25 and 0.27 of their widths: sin 15 degrees), a picture of its own set into the sheet; 5000 px)","scaleRef":"its length from the first shoulder's plane (row 3000) to its head end's plane (3780), 780 px, as .added_length: what it fills between the carrier and the buffer (the patent: \"This extension in length can compensate for the length added to the rifle by the addition of the folding stock adapter 100\"): 600 px/in along it, and 621 px/in across (its lengths are foreshortened by cos 15 degrees)","method":"its silhouette's width row by row (luminance under 200), its axis fitted through the rows' middles (0.38 degrees off upright); the pilot 355 px","via":"harvest"},"note":"rows 2728 (the end's plane, the middle of its rim's ellipse) to 3000 (272 px)"}]},"ext_collar_d":{"label":"Bolt carrier extension: the collar (its first shoulder), across","kind":"length","measurements":[{"id":"pa01","value":0.689,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: below the adapter, the bolt carrier extension standing on its head end, seen from in front and about 15 degrees above (its ends' rims are ellipses 0.25 and 0.27 of their widths: sin 15 degrees), a picture of its own set into the sheet; 5000 px)","scaleRef":"its length from the first shoulder's plane (row 3000) to its head end's plane (3780), 780 px, as .added_length: what it fills between the carrier and the buffer (the patent: \"This extension in length can compensate for the length added to the rifle by the addition of the folding stock adapter 100\"): 600 px/in along it, and 621 px/in across (its lengths are foreshortened by cos 15 degrees)","method":"its silhouette's width row by row (luminance under 200), its axis fitted through the rows' middles (0.38 degrees off upright); the pilot 355 px","via":"harvest"},"note":"428 px"}]},"ext_collar_length":{"label":"Bolt carrier extension: the collar, along","kind":"length","measurements":[{"id":"pa01","value":0.083,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: below the adapter, the bolt carrier extension standing on its head end, seen from in front and about 15 degrees above (its ends' rims are ellipses 0.25 and 0.27 of their widths: sin 15 degrees), a picture of its own set into the sheet; 5000 px)","scaleRef":"its length from the first shoulder's plane (row 3000) to its head end's plane (3780), 780 px, as .added_length: what it fills between the carrier and the buffer (the patent: \"This extension in length can compensate for the length added to the rifle by the addition of the folding stock adapter 100\"): 600 px/in along it, and 621 px/in across (its lengths are foreshortened by cos 15 degrees)","method":"its silhouette's width row by row (luminance under 200), its axis fitted through the rows' middles (0.38 degrees off upright); the pilot 355 px","via":"harvest"},"note":"rows 3000 to 3050"}]},"ext_neck_d":{"label":"Bolt carrier extension: the neck behind the collar, across","kind":"length","measurements":[{"id":"pa01","value":0.452,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: below the adapter, the bolt carrier extension standing on its head end, seen from in front and about 15 degrees above (its ends' rims are ellipses 0.25 and 0.27 of their widths: sin 15 degrees), a picture of its own set into the sheet; 5000 px)","scaleRef":"its length from the first shoulder's plane (row 3000) to its head end's plane (3780), 780 px, as .added_length: what it fills between the carrier and the buffer (the patent: \"This extension in length can compensate for the length added to the rifle by the addition of the folding stock adapter 100\"): 600 px/in along it, and 621 px/in across (its lengths are foreshortened by cos 15 degrees)","method":"its silhouette's width row by row (luminance under 200), its axis fitted through the rows' middles (0.38 degrees off upright); the pilot 355 px","via":"harvest"},"note":"281 px"}]},"ext_neck_length":{"label":"Bolt carrier extension: the neck, along (to where it flares)","kind":"length","measurements":[{"id":"pa01","value":0.233,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: below the adapter, the bolt carrier extension standing on its head end, seen from in front and about 15 degrees above (its ends' rims are ellipses 0.25 and 0.27 of their widths: sin 15 degrees), a picture of its own set into the sheet; 5000 px)","scaleRef":"its length from the first shoulder's plane (row 3000) to its head end's plane (3780), 780 px, as .added_length: what it fills between the carrier and the buffer (the patent: \"This extension in length can compensate for the length added to the rifle by the addition of the folding stock adapter 100\"): 600 px/in along it, and 621 px/in across (its lengths are foreshortened by cos 15 degrees)","method":"its silhouette's width row by row (luminance under 200), its axis fitted through the rows' middles (0.38 degrees off upright); the pilot 355 px","via":"harvest"},"note":"rows 3050 to 3190"}]},"ext_flare_d":{"label":"Bolt carrier extension: the cone's wide end, across (a step up to the body after it)","kind":"length","measurements":[{"id":"pa01","value":0.652,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: below the adapter, the bolt carrier extension standing on its head end, seen from in front and about 15 degrees above (its ends' rims are ellipses 0.25 and 0.27 of their widths: sin 15 degrees), a picture of its own set into the sheet; 5000 px)","scaleRef":"its length from the first shoulder's plane (row 3000) to its head end's plane (3780), 780 px, as .added_length: what it fills between the carrier and the buffer (the patent: \"This extension in length can compensate for the length added to the rifle by the addition of the folding stock adapter 100\"): 600 px/in along it, and 621 px/in across (its lengths are foreshortened by cos 15 degrees)","method":"its silhouette's width row by row (luminance under 200), its axis fitted through the rows' middles (0.38 degrees off upright); the pilot 355 px","via":"harvest"},"note":"405 px at row 3314, then 429 from 3322"}]},"ext_flare_length":{"label":"Bolt carrier extension: the cone from the neck to the body, along","kind":"length","measurements":[{"id":"pa01","value":0.217,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: below the adapter, the bolt carrier extension standing on its head end, seen from in front and about 15 degrees above (its ends' rims are ellipses 0.25 and 0.27 of their widths: sin 15 degrees), a picture of its own set into the sheet; 5000 px)","scaleRef":"its length from the first shoulder's plane (row 3000) to its head end's plane (3780), 780 px, as .added_length: what it fills between the carrier and the buffer (the patent: \"This extension in length can compensate for the length added to the rifle by the addition of the folding stock adapter 100\"): 600 px/in along it, and 621 px/in across (its lengths are foreshortened by cos 15 degrees)","method":"its silhouette's width row by row (luminance under 200), its axis fitted through the rows' middles (0.38 degrees off upright); the pilot 355 px","via":"harvest"},"note":"rows 3190 to 3320"}]},"ext_body_d":{"label":"Bolt carrier extension: the body, across","kind":"length","measurements":[{"id":"pa01","value":0.692,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: below the adapter, the bolt carrier extension standing on its head end, seen from in front and about 15 degrees above (its ends' rims are ellipses 0.25 and 0.27 of their widths: sin 15 degrees), a picture of its own set into the sheet; 5000 px)","scaleRef":"its length from the first shoulder's plane (row 3000) to its head end's plane (3780), 780 px, as .added_length: what it fills between the carrier and the buffer (the patent: \"This extension in length can compensate for the length added to the rifle by the addition of the folding stock adapter 100\"): 600 px/in along it, and 621 px/in across (its lengths are foreshortened by cos 15 degrees)","method":"its silhouette's width row by row (luminance under 200), its axis fitted through the rows' middles (0.38 degrees off upright); the pilot 355 px","via":"harvest"},"note":"430 px"}]},"ext_body_length":{"label":"Bolt carrier extension: the body, along","kind":"length","measurements":[{"id":"pa01","value":0.217,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: below the adapter, the bolt carrier extension standing on its head end, seen from in front and about 15 degrees above (its ends' rims are ellipses 0.25 and 0.27 of their widths: sin 15 degrees), a picture of its own set into the sheet; 5000 px)","scaleRef":"its length from the first shoulder's plane (row 3000) to its head end's plane (3780), 780 px, as .added_length: what it fills between the carrier and the buffer (the patent: \"This extension in length can compensate for the length added to the rifle by the addition of the folding stock adapter 100\"): 600 px/in along it, and 621 px/in across (its lengths are foreshortened by cos 15 degrees)","method":"its silhouette's width row by row (luminance under 200), its axis fitted through the rows' middles (0.38 degrees off upright); the pilot 355 px","via":"harvest"},"note":"rows 3320 to 3450"}]},"ext_stem_d":{"label":"Bolt carrier extension: the stem behind the body, across","kind":"length","measurements":[{"id":"pa01","value":0.467,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: below the adapter, the bolt carrier extension standing on its head end, seen from in front and about 15 degrees above (its ends' rims are ellipses 0.25 and 0.27 of their widths: sin 15 degrees), a picture of its own set into the sheet; 5000 px)","scaleRef":"its length from the first shoulder's plane (row 3000) to its head end's plane (3780), 780 px, as .added_length: what it fills between the carrier and the buffer (the patent: \"This extension in length can compensate for the length added to the rifle by the addition of the folding stock adapter 100\"): 600 px/in along it, and 621 px/in across (its lengths are foreshortened by cos 15 degrees)","method":"its silhouette's width row by row (luminance under 200), its axis fitted through the rows' middles (0.38 degrees off upright); the pilot 355 px","via":"harvest"},"note":"290 px"}]},"ext_stem_length":{"label":"Bolt carrier extension: the stem, along","kind":"length","measurements":[{"id":"pa01","value":0.427,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: below the adapter, the bolt carrier extension standing on its head end, seen from in front and about 15 degrees above (its ends' rims are ellipses 0.25 and 0.27 of their widths: sin 15 degrees), a picture of its own set into the sheet; 5000 px)","scaleRef":"its length from the first shoulder's plane (row 3000) to its head end's plane (3780), 780 px, as .added_length: what it fills between the carrier and the buffer (the patent: \"This extension in length can compensate for the length added to the rifle by the addition of the folding stock adapter 100\"): 600 px/in along it, and 621 px/in across (its lengths are foreshortened by cos 15 degrees)","method":"its silhouette's width row by row (luminance under 200), its axis fitted through the rows' middles (0.38 degrees off upright); the pilot 355 px","via":"harvest"},"note":"rows 3450 to 3706"}]},"ext_head_d":{"label":"Bolt carrier extension: its head (the end the buffer bears on), across","kind":"length","measurements":[{"id":"pa01","value":0.614,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: below the adapter, the bolt carrier extension standing on its head end, seen from in front and about 15 degrees above (its ends' rims are ellipses 0.25 and 0.27 of their widths: sin 15 degrees), a picture of its own set into the sheet; 5000 px)","scaleRef":"its length from the first shoulder's plane (row 3000) to its head end's plane (3780), 780 px, as .added_length: what it fills between the carrier and the buffer (the patent: \"This extension in length can compensate for the length added to the rifle by the addition of the folding stock adapter 100\"): 600 px/in along it, and 621 px/in across (its lengths are foreshortened by cos 15 degrees)","method":"its silhouette's width row by row (luminance under 200), its axis fitted through the rows' middles (0.38 degrees off upright); the pilot 355 px","via":"harvest"},"note":"381 px at its widest, where the flare from the stem ends"}]},"ext_head_length":{"label":"Bolt carrier extension: the head's flare, along","kind":"length","measurements":[{"id":"pa01","value":0.123,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: below the adapter, the bolt carrier extension standing on its head end, seen from in front and about 15 degrees above (its ends' rims are ellipses 0.25 and 0.27 of their widths: sin 15 degrees), a picture of its own set into the sheet; 5000 px)","scaleRef":"its length from the first shoulder's plane (row 3000) to its head end's plane (3780), 780 px, as .added_length: what it fills between the carrier and the buffer (the patent: \"This extension in length can compensate for the length added to the rifle by the addition of the folding stock adapter 100\"): 600 px/in along it, and 621 px/in across (its lengths are foreshortened by cos 15 degrees)","method":"its silhouette's width row by row (luminance under 200), its axis fitted through the rows' middles (0.38 degrees off upright); the pilot 355 px","via":"harvest"},"note":"rows 3706 to 3780"}]},"bolt_head_d":{"label":"The hinge bolt's socket head, across (in a counterbore in the upper tab's top)","kind":"length","measurements":[{"id":"assumed","value":0.3,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: Primary Arms' photo from behind and above (430116178_03) has a round head with its hex socket in the upper tab's top, most of the tab's width; its rim isn't read on a view square to it.","via":"harvest"}}]},"bolt_counterbore_d":{"label":"The counterbore the hinge bolt's head sits in, across","kind":"length","measurements":[{"id":"assumed","value":0.34,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: a thin wall of the tab round the head, as Primary Arms' photo from above shows it.","via":"harvest"}}]},"bolt_socket":{"label":"The hinge bolt's hex socket, across its flats","kind":"length","measurements":[{"id":"sheet","value":0.125,"unit":"in","pm":0.002,"stated":"Hinge Tension: A 1/8 Allen Wrench can be used to increase hinge tension by tightening the Hinge Screw (10).","source":{"type":"spec","publisher":"manufacturer","name":"Law Tactical, AR Folding Stock Adapter GEN-S instructions (Gen-3S_Instructions-web.pdf, text layer), Maintenance","url":"https://www.arfoldingstock.com/img/Gen-3S_Instructions-web.pdf","retrieved":"2026-10-18","via":"harvest"},"note":"The key that turns it is 1/8 in: its socket is that across the flats."}]},"bolt_head_recess":{"label":"How far the bolt's head stands under the upper tab's top","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: Primary Arms' photo from behind and above has the head about flush with the tab's top; by how much under, isn't seen.","via":"harvest"}}]},"bolt_head_height":{"label":"The bolt's head, its height (and the counterbore's depth under it)","kind":"length","measurements":[{"id":"assumed","value":0.15,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view shows the head in profile; about half its width, as a socket head is.","via":"harvest"}}]},"bolt_socket_depth":{"label":"The bolt head's hex socket, its depth","kind":"length","measurements":[{"id":"assumed","value":0.08,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the socket's floor isn't seen.","via":"harvest"}}]}}},{"subject":"law-tactical-gen3m-folder","title":"Law Tactical AR Folding Stock Adapter Gen 3-M","dimensions":{"weight":{"label":"Weight (the housing with its flange, and the bolt carrier extension)","kind":"mass","measurements":[{"id":"sum","value":10.5,"unit":"oz","pm":0.1,"source":{"type":"derived","expr":"{.housing_weight} + {.extension_weight}","via":"harvest"}}],"note":"What the box holds that goes on the rifle: the hinge assembly and its threaded flange (the sellers' \"Housing Weight\"; that the flange is in it is an assumption, no page says) and the bolt carrier extension, which they weigh apart. The flange tool and the sheet aren't counted."},"housing_weight":{"label":"Housing weight (the hinge assembly)","kind":"mass","measurements":[{"id":"trex","value":8.5,"unit":"oz","pm":0.05,"stated":"Made from CNC Machined 4140 Steel with DLC finish Housing Weight: 8.5 oz. Bolt Carrier Extension: 2 oz.","source":{"type":"spec","publisher":"retailer","name":"T.REX Arms, LAW Folder AR/M4 Gen 3 (its \"What's Included\": \"1x LAW Tactical AR Folding Stock Adapter Gen3-M\"), Specs","url":"https://www.trex-arms.com/store/law-folder-ar-m4-gen-3/","retrieved":"2026-10-18","via":"harvest"}},{"id":"recoil","value":8.5,"unit":"oz","pm":0.05,"stated":"Housing Weight: 8.5 oz Bolt Carrier Extension: 2 oz Adds 1.3 inches to length of pull CNC Machined 4140 Steel","source":{"type":"spec","publisher":"review","name":"RECOIL, Law Tactical Gen 3-M side folding AR stock (a news item listing the maker's figures)","url":"https://www.recoilweb.com/law-tactical-gen-3-m-side-folding-ar-stock-74183.html","retrieved":"2026-10-18","via":"harvest"}},{"id":"law","value":8.5,"unit":"oz","pm":0.07,"stated":"GEN-S SPECIFICATIONS Housing Weight: 7.4 oz ... 1.1 oz. Lighter than GEN 3-M","source":{"type":"derived","expr":"7.4oz + 1.1oz","via":"harvest"},"note":"Law Tactical's page for the Gen-S (at the Gen 3-M's address): its housing and how much lighter it is than this one's. The maker's own word, worked out."}],"adopt":{"from":"law","reason":"The maker's two figures for its successor, which say this one's; T.REX's list and RECOIL's item give the same 8.5 oz."}},"extension_weight":{"label":"Bolt carrier extension weight","kind":"mass","measurements":[{"id":"trex","value":2,"unit":"oz","pm":0.5,"stated":"Bolt Carrier Extension: 2 oz.","source":{"type":"spec","publisher":"retailer","name":"T.REX Arms, LAW Folder AR/M4 Gen 3 (its \"What's Included\": \"1x LAW Tactical AR Folding Stock Adapter Gen3-M\"), Specs","url":"https://www.trex-arms.com/store/law-folder-ar-m4-gen-3/","retrieved":"2026-10-18","via":"harvest"}},{"id":"recoil","value":2,"unit":"oz","pm":0.5,"stated":"Bolt Carrier Extension: 2 oz","source":{"type":"spec","publisher":"review","name":"RECOIL, Law Tactical Gen 3-M side folding AR stock (a news item listing the maker's figures)","url":"https://www.recoilweb.com/law-tactical-gen-3-m-side-folding-ar-stock-74183.html","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"trex","reason":"A seller's list, and RECOIL's item gives the same; both quote the maker."}},"added_length":{"label":"How far it moves the receiver extension back","kind":"length","measurements":[{"id":"trex","value":1.3,"unit":"in","pm":0.05,"stated":"Adds 1.3 inches to length of pull","source":{"type":"spec","publisher":"retailer","name":"T.REX Arms, LAW Folder AR/M4 Gen 3 (its \"What's Included\": \"1x LAW Tactical AR Folding Stock Adapter Gen3-M\"), Specs","url":"https://www.trex-arms.com/store/law-folder-ar-m4-gen-3/","retrieved":"2026-10-18","via":"harvest"}},{"id":"recoil","value":1.3,"unit":"in","pm":0.05,"stated":"Adds 1.3 inches to length of pull","source":{"type":"spec","publisher":"review","name":"RECOIL, Law Tactical Gen 3-M side folding AR stock (a news item listing the maker's figures)","url":"https://www.recoilweb.com/law-tactical-gen-3-m-side-folding-ar-stock-74183.html","retrieved":"2026-10-18","via":"harvest"}},{"id":"trex-folded","value":1.25,"unit":"in","pm":0.005,"stated":"When folded, it adds 1.25 inches to the back of the receiver","source":{"type":"spec","publisher":"retailer","name":"T.REX Arms, LAW Folder AR/M4 Gen 3 (its \"What's Included\": \"1x LAW Tactical AR Folding Stock Adapter Gen3-M\"), Specs","url":"https://www.trex-arms.com/store/law-folder-ar-m4-gen-3/","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"trex","reason":"The length of pull is what the stock moves back by, which is this; RECOIL gives the same, and the maker's page says it of the Gen-S. T.REX's folded figure is another measure (what the folded rifle has behind its receiver) and is within the 1.3's last digit."},"note":"The tube screws into the stock half as into a lower, so the stock half's rear face is the receiver's rear face moved back by this. T.REX's second figure is kept beside it: read as what stands behind the receiver when the stock is folded, it would have the hinge far behind where the halves meet, which the photos of the part folded open (the two mating faces in one plane) and the patent's FIG. 6B (folded, about half the adapter behind the receiver) don't bear out. No side photo with a lower's pins in frame is on file to check either."},"length":{"label":"Its length along the bore (the housing, front face to rear face)","kind":"length","measurements":[{"id":"added","value":1.3,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{.added_length}","via":"harvest"}}],"note":"The receiver half's front face bears on the lower's rear face (std.ar15.receiver_rear_x) and the stock half's rear face stands where a lower's would: the housing is as long as it moves the tube back. The threaded flange reaches forward of it into the lower's ring."},"receiver_half_length":{"label":"The receiver half, front face to where the halves meet","kind":"length","measurements":[{"id":"seam","value":0.65,"unit":"in","pm":0.1,"source":{"type":"derived","expr":"{.hinge_x} + {std.ar15.receiver_rear_x}","via":"harvest"}}],"note":"Where the halves meet is in the hinge's plane (.hinge_x): folded open 180 degrees their two mating faces lie in one plane side by side (RECOIL's 55fec2c093b8 from behind, T.REX's d540fee687f5 from above), which a seam ahead of or behind the axis would offset by twice its distance. No square side view of the part is on file to read it on directly."},"stock_half_length":{"label":"The stock half, where the halves meet to its rear face","kind":"length","measurements":[{"id":"rest","value":0.65,"unit":"in","pm":0.1,"source":{"type":"derived","expr":"{.length} - {.receiver_half_length}","via":"harvest"}}]},"hinge_x":{"label":"The hinge's axis behind the takedown pin","kind":"length","measurements":[{"id":"photo","value":1.775,"unit":"in","pm":0.1,"source":{"type":"derived","expr":"0in - {std.ar15.receiver_rear_x} + {.length} / 2","via":"harvest"}}],"note":"Half the housing's length behind the lower's rear face (the Army's drawing): on T.REX's photo from above (d540fee687f5) the part lies folded open 180 degrees with each half flat on its outer face (the receiver half's front, the stock half's rear: both bores read as circles to 2 px, so neither is propped) and the hinge's axis level between them, which puts the axis as far from the one outer face as from the other. The two halves' outlines' top arcs read alike (315.1 and 315.3 px across), so their mating faces stand at one height too: the halves are of a length. The patent's FIG. 6A (an earlier embodiment, not held to scale) draws the knuckles three quarters of the way back."},"hinge_z":{"label":"The hinge's axis out from the tube's axis, toward the side it folds to (the rifle's left)","kind":"length","measurements":[{"id":"trex","value":1.137,"unit":"in","pm":0.035,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder d540fee687f5 (T.REX Arms' gallery, LAW-Folder-M4-AR-Gen-3-TAN-7939.jpg: the FDE adapter folded open 180 degrees on a slate table, both mating faces up, from straight above; 3000 x 3000)","scaleRef":"the stock half's threaded bore seen through to the table: a RANSAC circle on the hole's rim, centre (1092.2, 1399.8), 400.0 px across, as .bore_thread_crest_d (347.4 px/in); the receiver half's bore, centre (1882.3, 1399.8), on the same row: the photo isn't rolled","method":"half the bores' centres' distance, 790.1 px / 2 = 395.0 px. The hinge's own column (its knuckles' outer edges and the knurled nut under them, rows 1421 to 1925) is centred on 1480 ± 6, 7 px short of midway. ± covers the scale's (the thread's crest diameter, 2.6%) and those 7 px","via":"harvest"}}],"note":"Folded open 180 degrees about the hinge, the two halves' bores stand side by side twice this apart, with the hinge midway: read on T.REX's photo of that pose, scaled by the stock half's threaded bore in the same plane (a second reading, on Law Tactical's gallery photo 3b8c6c1cb2e2, was taken out: that photo is the GEN-S, Primary Arms' picture of it cropped; no other photo of this part square to that pose is on file). The side is the left: in T.REX's photo and RECOIL's of that pose the halves' mating faces are toward the lens (as they face rearward when folded), the receiver half (its latch and \"CLOSE BEFORE FIRING\") is on the right and the stock half on the left; the instruction sheet's steps 4 to 6 draw the folded stock half on the near side of a lower shown from its left (muzzle to the left); the patent's FIG. 6B draws the folded stock in front of the receiver in a view of the left side; and RECOIL's picture of a rifle folded (484aef9fa092) has the stock across the left side."},"fold_max":{"label":"How far the hinge turns before its own halves stop it","kind":"angle","measurements":[{"id":"photo","value":180,"unit":"deg","pm":5,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder d540fee687f5 (T.REX Arms' gallery, LAW-Folder-M4-AR-Gen-3-TAN-7939.jpg: the FDE adapter folded open 180 degrees on a slate table, both mating faces up, from straight above; 3000 x 3000)","scaleRef":"angles: both bores read as circles (RANSAC fits, rms 2 px) on one row, the faces square to the lens","method":"the two halves' faces in one plane, side by side; read with US 8,769,855: \"the stock can be folded flat against the receiver when the folding stock adapter is in an open position\" (col. 3, l. 51 to 53)","via":"harvest"}}],"note":"Folded open on a table (T.REX, RECOIL) the halves lie side by side with their mating faces in one plane, and between the rings below them the two halves' lugs meet across the hinge: the patent says the stock \"can be folded flat against the receiver\". No page states an angle, and no photo shows it turned past that; how far the stock itself goes on a rifle before it meets the receiver is the build's (the app works it out)."},"bore_thread_crest_d":{"label":"The stock half's threaded bore: its thread's crests (what one sees through it)","kind":"length","measurements":[{"id":"thread","value":1.1515,"unit":"in","pm":0.0295,"source":{"type":"derived","expr":"({std.receiver_extension.thread_major_d} / 1.0529 + {std.receiver_extension.thread_major_d}) / 2","via":"harvest"},"note":"The middle of 1.122 (the flange's major diameter over the two bores' ratio, 421.2 / 400.0 px: the receiver half's bore has to pass it) and 1.1813 (the extension's major diameter, which a hole's crests are under); ± half that span."}],"note":"The scale of every photo here. The receiver extension screws in as into a lower (the sheet: \"in the same manner it would be installed onto the rear of the rifle receiver\"), so this is a 1 3/16-16 thread in a hole: its crests lie between the extension's own minor and major diameters (the Army's limits). The receiver half's bore, read beside it in the same photo at 1.053 times this, has to pass the threaded flange (std major 1.1813): that puts this at 1.122 or more."},"receiver_bore_d":{"label":"The receiver half's bore (where the flange passes, at its narrowest)","kind":"length","measurements":[{"id":"trex","value":1.213,"unit":"in","pm":0.032,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder d540fee687f5 (T.REX Arms' gallery, LAW-Folder-M4-AR-Gen-3-TAN-7939.jpg: the FDE adapter folded open 180 degrees on a slate table, both mating faces up, from straight above; 3000 x 3000)","scaleRef":"the stock half's threaded bore seen through to the table: a RANSAC circle on the hole's rim, centre (1092.2, 1399.8), 400.0 px across, as .bore_thread_crest_d (347.4 px/in); the receiver half's bore, centre (1882.3, 1399.8), on the same row: the photo isn't rolled","method":"a RANSAC circle on the hole's rim, 421.2 px across (the black latch inside it masked by the fit's tolerance)","via":"harvest"}}],"note":"A second reading on Law Tactical's gallery photo 3b8c6c1cb2e2 was taken out (2026-10-18): that photo is the GEN-S, not this part."},"body_top_above_axis":{"label":"The rings' tops above the tube's axis","kind":"length","measurements":[{"id":"trex","value":0.734,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder d540fee687f5 (T.REX Arms' gallery, LAW-Folder-M4-AR-Gen-3-TAN-7939.jpg: the FDE adapter folded open 180 degrees on a slate table, both mating faces up, from straight above; 3000 x 3000)","scaleRef":"the stock half's threaded bore seen through to the table: a RANSAC circle on the hole's rim, centre (1092.2, 1399.8), 400.0 px across, as .bore_thread_crest_d (347.4 px/in); the receiver half's bore, centre (1882.3, 1399.8), on the same row: the photo isn't rolled","method":"the receiver half's outline's top, 255 px above its bore's centre (the stock half's 0.713: its ring is a little lower)","via":"harvest"}}]},"body_bottom_below_axis":{"label":"Its feet below the tube's axis","kind":"length","measurements":[{"id":"trex","value":1.532,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder d540fee687f5 (T.REX Arms' gallery, LAW-Folder-M4-AR-Gen-3-TAN-7939.jpg: the FDE adapter folded open 180 degrees on a slate table, both mating faces up, from straight above; 3000 x 3000)","scaleRef":"the stock half's threaded bore seen through to the table: a RANSAC circle on the hole's rim, centre (1092.2, 1399.8), 400.0 px across, as .bore_thread_crest_d (347.4 px/in); the receiver half's bore, centre (1882.3, 1399.8), on the same row: the photo isn't rolled","method":"both halves' outlines' lowest rows, 532 px below the bores' centres","via":"harvest"}}]},"height":{"label":"Its height","kind":"length","measurements":[{"id":"sum","value":2.266,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.body_top_above_axis} + {.body_bottom_below_axis}","via":"harvest"}}]},"far_side":{"label":"Its side away from the hinge (the rifle's right), out from the tube's axis","kind":"length","measurements":[{"id":"trex","value":0.79,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder d540fee687f5 (T.REX Arms' gallery, LAW-Folder-M4-AR-Gen-3-TAN-7939.jpg: the FDE adapter folded open 180 degrees on a slate table, both mating faces up, from straight above; 3000 x 3000)","scaleRef":"the stock half's threaded bore seen through to the table: a RANSAC circle on the hole's rim, centre (1092.2, 1399.8), 400.0 px across, as .bore_thread_crest_d (347.4 px/in); the receiver half's bore, centre (1882.3, 1399.8), on the same row: the photo isn't rolled","method":"the receiver half's straight side, 274 px from its bore's centre (rows 1380 to 1770; the stock half's side reads 0.786 at its widest); the button's bar stands out past it","via":"harvest"}}]},"knuckle_d":{"label":"The hinge's two outer knuckles (the stock half's tabs), across","kind":"length","measurements":[{"id":"trex","value":0.481,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder d540fee687f5 (T.REX Arms' gallery, LAW-Folder-M4-AR-Gen-3-TAN-7939.jpg: the FDE adapter folded open 180 degrees on a slate table, both mating faces up, from straight above; 3000 x 3000)","scaleRef":"the stock half's threaded bore seen through to the table: a RANSAC circle on the hole's rim, centre (1092.2, 1399.8), 400.0 px across, as .bore_thread_crest_d (347.4 px/in); the receiver half's bore, centre (1882.3, 1399.8), on the same row: the photo isn't rolled","method":"the upper tab seen from the side, 167 px across (columns 1405 to 1572)","via":"harvest"}}]},"pivot_d":{"label":"The hinge's middle knuckle (the receiver half's pivot block), across","kind":"length","measurements":[{"id":"trex","value":0.63,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder d540fee687f5 (T.REX Arms' gallery, LAW-Folder-M4-AR-Gen-3-TAN-7939.jpg: the FDE adapter folded open 180 degrees on a slate table, both mating faces up, from straight above; 3000 x 3000)","scaleRef":"the stock half's threaded bore seen through to the table: a RANSAC circle on the hole's rim, centre (1092.2, 1399.8), 400.0 px across, as .bore_thread_crest_d (347.4 px/in); the receiver half's bore, centre (1882.3, 1399.8), on the same row: the photo isn't rolled","method":"seen from the side, 219 px across (columns 1368 to 1588 on row 1660, its edge lines included)","via":"harvest"}}]},"washer_d":{"label":"The black washers between the knuckles, across","kind":"length","measurements":[{"id":"trex","value":0.527,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder d540fee687f5 (T.REX Arms' gallery, LAW-Folder-M4-AR-Gen-3-TAN-7939.jpg: the FDE adapter folded open 180 degrees on a slate table, both mating faces up, from straight above; 3000 x 3000)","scaleRef":"the stock half's threaded bore seen through to the table: a RANSAC circle on the hole's rim, centre (1092.2, 1399.8), 400.0 px across, as .bore_thread_crest_d (347.4 px/in); the receiver half's bore, centre (1882.3, 1399.8), on the same row: the photo isn't rolled","method":"183 px (columns 1385 to 1568)","via":"harvest"}}]},"upper_tab_top":{"label":"The upper tab's top, below the tube's axis","kind":"length","measurements":[{"id":"trex","value":0.061,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder d540fee687f5 (T.REX Arms' gallery, LAW-Folder-M4-AR-Gen-3-TAN-7939.jpg: the FDE adapter folded open 180 degrees on a slate table, both mating faces up, from straight above; 3000 x 3000)","scaleRef":"the stock half's threaded bore seen through to the table: a RANSAC circle on the hole's rim, centre (1092.2, 1399.8), 400.0 px across, as .bore_thread_crest_d (347.4 px/in); the receiver half's bore, centre (1882.3, 1399.8), on the same row: the photo isn't rolled","method":"along the hinge's column (1480): the tan of the tab begins at row 1421","via":"harvest"}}]},"upper_tab_bottom":{"label":"The upper tab's bottom, below the tube's axis","kind":"length","measurements":[{"id":"trex","value":0.409,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder d540fee687f5 (T.REX Arms' gallery, LAW-Folder-M4-AR-Gen-3-TAN-7939.jpg: the FDE adapter folded open 180 degrees on a slate table, both mating faces up, from straight above; 3000 x 3000)","scaleRef":"the stock half's threaded bore seen through to the table: a RANSAC circle on the hole's rim, centre (1092.2, 1399.8), 400.0 px across, as .bore_thread_crest_d (347.4 px/in); the receiver half's bore, centre (1882.3, 1399.8), on the same row: the photo isn't rolled","method":"row 1542, where the black washer begins","via":"harvest"}}]},"pivot_top":{"label":"The middle knuckle's top, below the tube's axis","kind":"length","measurements":[{"id":"trex","value":0.542,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder d540fee687f5 (T.REX Arms' gallery, LAW-Folder-M4-AR-Gen-3-TAN-7939.jpg: the FDE adapter folded open 180 degrees on a slate table, both mating faces up, from straight above; 3000 x 3000)","scaleRef":"the stock half's threaded bore seen through to the table: a RANSAC circle on the hole's rim, centre (1092.2, 1399.8), 400.0 px across, as .bore_thread_crest_d (347.4 px/in); the receiver half's bore, centre (1882.3, 1399.8), on the same row: the photo isn't rolled","method":"row 1589","via":"harvest"}}]},"pivot_bottom":{"label":"The middle knuckle's bottom, below the tube's axis","kind":"length","measurements":[{"id":"trex","value":0.968,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder d540fee687f5 (T.REX Arms' gallery, LAW-Folder-M4-AR-Gen-3-TAN-7939.jpg: the FDE adapter folded open 180 degrees on a slate table, both mating faces up, from straight above; 3000 x 3000)","scaleRef":"the stock half's threaded bore seen through to the table: a RANSAC circle on the hole's rim, centre (1092.2, 1399.8), 400.0 px across, as .bore_thread_crest_d (347.4 px/in); the receiver half's bore, centre (1882.3, 1399.8), on the same row: the photo isn't rolled","method":"row 1737","via":"harvest"}}]},"lower_tab_top":{"label":"The lower tab's top, below the tube's axis","kind":"length","measurements":[{"id":"trex","value":1.1,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder d540fee687f5 (T.REX Arms' gallery, LAW-Folder-M4-AR-Gen-3-TAN-7939.jpg: the FDE adapter folded open 180 degrees on a slate table, both mating faces up, from straight above; 3000 x 3000)","scaleRef":"the stock half's threaded bore seen through to the table: a RANSAC circle on the hole's rim, centre (1092.2, 1399.8), 400.0 px across, as .bore_thread_crest_d (347.4 px/in); the receiver half's bore, centre (1882.3, 1399.8), on the same row: the photo isn't rolled","method":"row 1783","via":"harvest"}}]},"lower_tab_bottom":{"label":"The lower tab's bottom, below the tube's axis","kind":"length","measurements":[{"id":"trex","value":1.284,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder d540fee687f5 (T.REX Arms' gallery, LAW-Folder-M4-AR-Gen-3-TAN-7939.jpg: the FDE adapter folded open 180 degrees on a slate table, both mating faces up, from straight above; 3000 x 3000)","scaleRef":"the stock half's threaded bore seen through to the table: a RANSAC circle on the hole's rim, centre (1092.2, 1399.8), 400.0 px across, as .bore_thread_crest_d (347.4 px/in); the receiver half's bore, centre (1882.3, 1399.8), on the same row: the photo isn't rolled","method":"row 1848, where the knurled nut begins","via":"harvest"}}]},"nut_d":{"label":"The hinge bolt's knurled nut, across","kind":"length","measurements":[{"id":"trex","value":0.36,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder d540fee687f5 (T.REX Arms' gallery, LAW-Folder-M4-AR-Gen-3-TAN-7939.jpg: the FDE adapter folded open 180 degrees on a slate table, both mating faces up, from straight above; 3000 x 3000)","scaleRef":"the stock half's threaded bore seen through to the table: a RANSAC circle on the hole's rim, centre (1092.2, 1399.8), 400.0 px across, as .bore_thread_crest_d (347.4 px/in); the receiver half's bore, centre (1882.3, 1399.8), on the same row: the photo isn't rolled","method":"125 px (columns 1418 to 1543)","via":"harvest"}}]},"nut_bottom":{"label":"The knurled nut's end, below the tube's axis","kind":"length","measurements":[{"id":"trex","value":1.511,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder d540fee687f5 (T.REX Arms' gallery, LAW-Folder-M4-AR-Gen-3-TAN-7939.jpg: the FDE adapter folded open 180 degrees on a slate table, both mating faces up, from straight above; 3000 x 3000)","scaleRef":"the stock half's threaded bore seen through to the table: a RANSAC circle on the hole's rim, centre (1092.2, 1399.8), 400.0 px across, as .bore_thread_crest_d (347.4 px/in); the receiver half's bore, centre (1882.3, 1399.8), on the same row: the photo isn't rolled","method":"row 1925, the knurl's end","via":"harvest"}}]},"width":{"label":"Its width across the rifle, the hinge included (the button's bar not)","kind":"length","measurements":[{"id":"sum","value":2.2565,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{.far_side} + {.hinge_z} + {.pivot_d} / 2","via":"harvest"}}]},"stock_hole_small_d":{"label":"The stock half's rear face: its two small holes, across","kind":"length","measurements":[{"id":"blackstone","value":0.22,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder 3e86c09fb510 (Blackstone's photo of the black adapter closed, from behind, the left and above; 700 px)","scaleRef":"the threaded bore's width across the face, 285 px as .bore_thread_crest_d (the face is turned about a level axis: its widths are square, its heights foreshortened)","method":"55 px across each hole","via":"harvest"}}]},"stock_hole_small_apart":{"label":"The two small holes, each out from the middle","kind":"length","measurements":[{"id":"blackstone","value":0.33,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder 3e86c09fb510 (Blackstone, closed, from behind and above; 700 px)","scaleRef":"the threaded bore's width, 285 px","method":"centres 90 and 75 px either side of the bore's middle (columns 210 and 375 against 300), the mean","via":"harvest"}}]},"stock_hole_small_below_axis":{"label":"The two small holes' centres below the tube's axis","kind":"length","measurements":[{"id":"blackstone","value":0.69,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder 3e86c09fb510 (Blackstone, closed, from behind and above; 700 px)","scaleRef":"the face's own height from the bore's centre (row 310) to its feet (row 650) as .body_bottom_below_axis: the face is foreshortened up and down","method":"rows 455 and 470: 0.43 and 0.47 of the way down","via":"harvest"}}]},"stock_hole_big_d":{"label":"The stock half's rear face: its large hole (where an A2 stock's tab would go), across","kind":"length","measurements":[{"id":"blackstone","value":0.44,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder 3e86c09fb510 (Blackstone, closed, from behind and above; 700 px)","scaleRef":"the threaded bore's width, 285 px","method":"110 px across (columns 235 to 345), centred under the bore","via":"harvest"}}]},"stock_hole_big_below_axis":{"label":"The large hole's centre below the tube's axis","kind":"length","measurements":[{"id":"blackstone","value":1.13,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder 3e86c09fb510 (Blackstone, closed, from behind and above; 700 px)","scaleRef":"the face's height from the bore's centre to its feet as .body_bottom_below_axis","method":"row 560: 0.735 of the way down","via":"harvest"}}]},"stock_hole_depth":{"label":"How deep the rear face's three holes go","kind":"length","measurements":[{"id":"assumed","value":0.4,"unit":"in","pm":0.15,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the holes are dark to their floors in every photo of the rear face, and the stock half's front face has none (they are blind). Taken a little over half the half's length.","via":"harvest"}}]},"tab_width":{"label":"The stock half's locking tab, across (on its front face, low on the side away from the hinge)","kind":"length","measurements":[{"id":"trex","value":0.22,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder d540fee687f5 (T.REX Arms' gallery, LAW-Folder-M4-AR-Gen-3-TAN-7939.jpg: the FDE adapter folded open 180 degrees on a slate table, both mating faces up, from straight above; 3000 x 3000)","scaleRef":"the stock half's threaded bore seen through to the table: a RANSAC circle on the hole's rim, centre (1092.2, 1399.8), 400.0 px across, as .bore_thread_crest_d (347.4 px/in); the receiver half's bore, centre (1882.3, 1399.8), on the same row: the photo isn't rolled","method":"the raised rounded pad on the stock half's face, columns 940 to 1017 (77 px)","via":"harvest"}}]},"tab_height":{"label":"The locking tab, up and down","kind":"length","measurements":[{"id":"trex","value":0.4,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder d540fee687f5 (T.REX Arms' gallery, LAW-Folder-M4-AR-Gen-3-TAN-7939.jpg: the FDE adapter folded open 180 degrees on a slate table, both mating faces up, from straight above; 3000 x 3000)","scaleRef":"the stock half's threaded bore seen through to the table: a RANSAC circle on the hole's rim, centre (1092.2, 1399.8), 400.0 px across, as .bore_thread_crest_d (347.4 px/in); the receiver half's bore, centre (1882.3, 1399.8), on the same row: the photo isn't rolled","method":"rows 1638 to 1778 (140 px)","via":"harvest"}}]},"tab_centre_out":{"label":"The locking tab's middle, out from the tube's axis toward the side away from the hinge","kind":"length","measurements":[{"id":"trex","value":0.327,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder d540fee687f5 (T.REX Arms' gallery, LAW-Folder-M4-AR-Gen-3-TAN-7939.jpg: the FDE adapter folded open 180 degrees on a slate table, both mating faces up, from straight above; 3000 x 3000)","scaleRef":"the stock half's threaded bore seen through to the table: a RANSAC circle on the hole's rim, centre (1092.2, 1399.8), 400.0 px across, as .bore_thread_crest_d (347.4 px/in); the receiver half's bore, centre (1882.3, 1399.8), on the same row: the photo isn't rolled","method":"column 978.5, 113.7 px from the stock half's bore centre","via":"harvest"}}]},"tab_centre_below_axis":{"label":"The locking tab's middle below the tube's axis","kind":"length","measurements":[{"id":"trex","value":0.887,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder d540fee687f5 (T.REX Arms' gallery, LAW-Folder-M4-AR-Gen-3-TAN-7939.jpg: the FDE adapter folded open 180 degrees on a slate table, both mating faces up, from straight above; 3000 x 3000)","scaleRef":"the stock half's threaded bore seen through to the table: a RANSAC circle on the hole's rim, centre (1092.2, 1399.8), 400.0 px across, as .bore_thread_crest_d (347.4 px/in); the receiver half's bore, centre (1882.3, 1399.8), on the same row: the photo isn't rolled","method":"row 1708","via":"harvest"}}]},"tab_proud":{"label":"How far the locking tab stands forward of the stock half's face","kind":"length","measurements":[{"id":"assumed","value":0.15,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows the tab in profile. The patent's tab 135 goes into the receiver half's indentation 120, where the button's retainer catches it.","via":"harvest"}}]},"window_width":{"label":"The receiver half's window for the locking tab and the button's retainer, across","kind":"length","measurements":[{"id":"trex","value":0.36,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder d540fee687f5 (T.REX Arms' gallery, LAW-Folder-M4-AR-Gen-3-TAN-7939.jpg: the FDE adapter folded open 180 degrees on a slate table, both mating faces up, from straight above; 3000 x 3000)","scaleRef":"the stock half's threaded bore seen through to the table: a RANSAC circle on the hole's rim, centre (1092.2, 1399.8), 400.0 px across, as .bore_thread_crest_d (347.4 px/in); the receiver half's bore, centre (1882.3, 1399.8), on the same row: the photo isn't rolled","method":"the dark opening on the receiver half's face beside \"CLOSE BEFORE FIRING\", columns 1913 to 2038","via":"harvest"}}]},"window_height":{"label":"The window, up and down","kind":"length","measurements":[{"id":"trex","value":0.45,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder d540fee687f5 (T.REX Arms' gallery, LAW-Folder-M4-AR-Gen-3-TAN-7939.jpg: the FDE adapter folded open 180 degrees on a slate table, both mating faces up, from straight above; 3000 x 3000)","scaleRef":"the stock half's threaded bore seen through to the table: a RANSAC circle on the hole's rim, centre (1092.2, 1399.8), 400.0 px across, as .bore_thread_crest_d (347.4 px/in); the receiver half's bore, centre (1882.3, 1399.8), on the same row: the photo isn't rolled","method":"rows 1669 to 1825","via":"harvest"}}]},"window_depth":{"label":"How deep the window goes into the receiver half","kind":"length","measurements":[{"id":"assumed","value":0.3,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: deep enough for the tab (.tab_proud) and the button's retainer behind it; no view shows its floor.","via":"harvest"}}]},"button_width":{"label":"The button's bar out of the receiver half's side (the rifle's right), up and down","kind":"length","measurements":[{"id":"trex","value":0.29,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder d540fee687f5 (T.REX Arms' gallery, LAW-Folder-M4-AR-Gen-3-TAN-7939.jpg: the FDE adapter folded open 180 degrees on a slate table, both mating faces up, from straight above; 3000 x 3000)","scaleRef":"the stock half's threaded bore seen through to the table: a RANSAC circle on the hole's rim, centre (1092.2, 1399.8), 400.0 px across, as .bore_thread_crest_d (347.4 px/in); the receiver half's bore, centre (1882.3, 1399.8), on the same row: the photo isn't rolled","method":"the black bar standing out past the side, rows 1662 to 1763","via":"harvest"}}]},"button_proud":{"label":"How far the button's bar stands out of the side","kind":"length","measurements":[{"id":"trex","value":0.18,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder d540fee687f5 (T.REX Arms' gallery, LAW-Folder-M4-AR-Gen-3-TAN-7939.jpg: the FDE adapter folded open 180 degrees on a slate table, both mating faces up, from straight above; 3000 x 3000)","scaleRef":"the stock half's threaded bore seen through to the table: a RANSAC circle on the hole's rim, centre (1092.2, 1399.8), 400.0 px across, as .bore_thread_crest_d (347.4 px/in); the receiver half's bore, centre (1882.3, 1399.8), on the same row: the photo isn't rolled","method":"to column 2224, 63 px past the side's straight edge","via":"harvest"}}]},"button_below_axis":{"label":"The button's bar's middle below the tube's axis","kind":"length","measurements":[{"id":"trex","value":0.9,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder d540fee687f5 (T.REX Arms' gallery, LAW-Folder-M4-AR-Gen-3-TAN-7939.jpg: the FDE adapter folded open 180 degrees on a slate table, both mating faces up, from straight above; 3000 x 3000)","scaleRef":"the stock half's threaded bore seen through to the table: a RANSAC circle on the hole's rim, centre (1092.2, 1399.8), 400.0 px across, as .bore_thread_crest_d (347.4 px/in); the receiver half's bore, centre (1882.3, 1399.8), on the same row: the photo isn't rolled","method":"row 1712","via":"harvest"}}]},"flange_head_d":{"label":"The threaded flange's head, across (it sits in the receiver half)","kind":"length","measurements":[{"id":"assumed","value":1.3,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the head bears on a lip inside the receiver half's bore (the patent: \"a head 114, which can be configured to abut up against a raised lip 146 located within the dead hinge section opening 123\"); a little over the lip, .receiver_bore_d. Hidden when the adapter is on a rifle.","via":"harvest"}}]},"flange_head_length":{"label":"The flange's head, along the bore","kind":"length","measurements":[{"id":"assumed","value":0.12,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: Midwest Gun Works' photos of this part's flange (af70d3e9c54e, 93ed44e08726) have its slotted head a fraction of the ring's length, each a picture with nothing in its plane to scale it by; it is hidden on a rifle.","via":"harvest"}}]},"ext_pilot_d":{"label":"Bolt carrier extension: the end that goes into the carrier, across (its O-rings)","kind":"length","measurements":[{"id":"mgw-fde","value":0.599,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder 93ed44e08726 (Midwest Gun Works, LTGEN3MFDE: the FDE Gen 3-M closed, its black bolt carrier extension standing on its head end beside it, seen from in front and 17 degrees above (its top end's rim an ellipse 0.30 of its width); 1500 px)","scaleRef":"its length from the first shoulder's plane (row 576) to its head end's plane (841), 265 px, as .added_length: what it fills between the carrier and the buffer (the patent: \"This extension in length can compensate for the length added to the rifle by the addition of the folding stock adapter 100\"): 203.8 px/in along it, and 213.6 px/in across (its lengths foreshortened by cos 17.4 degrees)","method":"its silhouette's width row by row (luminance under 200), its axis fitted through the rows' middles (2.3 degrees off upright) and the widths taken square to it; a plane is the row where the silhouette reaches that section's full width; the pilot 128 px","via":"harvest"}},{"id":"mgw-black","value":0.613,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder af70d3e9c54e (Midwest Gun Works, 99312_Z: the black Gen 3-M closed, its bolt carrier extension standing on its head end beside it, seen from in front and 28 degrees above (its top end's rim an ellipse 0.47 of its width); 1500 px)","scaleRef":"its length from the first shoulder's plane (row 516) to its head end's plane (777), 261 px, as .added_length: 200.8 px/in along it, and 228.2 px/in across (cos 28.3 degrees)","method":"as the FDE photo's (its axis 4.4 degrees off upright); the pilot 140 px","via":"harvest"}}],"adopt":{"from":"mgw-fde","reason":"Nearer side-on (17 degrees above level against 28): its lengths, and so its scale, depend less on the elevation read off the top end's rim. The two agree within their ±."},"note":"The carrier's tail is bored .625 (std.ar15.carrier_tail_bore), and this end goes in to its first shoulder with O-rings that hold it: read at this scale on the two photos it is 0.012 to 0.026 under the bore, which the O-rings' stand makes up. (Read until 2026-10-18 on Law Tactical's 99312-5, which is the GEN-S's extension, not this part's.)"},"ext_pilot_length":{"label":"Bolt carrier extension: the end in the carrier, to its first shoulder","kind":"length","measurements":[{"id":"mgw-fde","value":0.466,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder 93ed44e08726 (Midwest Gun Works, LTGEN3MFDE: the FDE Gen 3-M closed, its black bolt carrier extension standing on its head end beside it, seen from in front and 17 degrees above (its top end's rim an ellipse 0.30 of its width); 1500 px)","scaleRef":"its length from the first shoulder's plane (row 576) to its head end's plane (841), 265 px, as .added_length: what it fills between the carrier and the buffer (the patent: \"This extension in length can compensate for the length added to the rifle by the addition of the folding stock adapter 100\"): 203.8 px/in along it, and 213.6 px/in across (its lengths foreshortened by cos 17.4 degrees)","method":"its silhouette's width row by row (luminance under 200), its axis fitted through the rows' middles (2.3 degrees off upright) and the widths taken square to it; a plane is the row where the silhouette reaches that section's full width; the pilot 128 px","via":"harvest"},"note":"rows 481 (the top end's plane) to 576 (95 px)"},{"id":"mgw-black","value":0.493,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder af70d3e9c54e (Midwest Gun Works, 99312_Z: the black Gen 3-M closed, its bolt carrier extension standing on its head end beside it, seen from in front and 28 degrees above (its top end's rim an ellipse 0.47 of its width); 1500 px)","scaleRef":"its length from the first shoulder's plane (row 516) to its head end's plane (777), 261 px, as .added_length: 200.8 px/in along it, and 228.2 px/in across (cos 28.3 degrees)","method":"as the FDE photo's (its axis 4.4 degrees off upright); the pilot 140 px","via":"harvest"},"note":"rows 417 to 516 (99 px)"}],"adopt":{"from":"mgw-fde","reason":"Nearer side-on; the two agree within their ±."}},"ext_collar_d":{"label":"Bolt carrier extension: the collar (its first shoulder), across","kind":"length","measurements":[{"id":"mgw-fde","value":0.712,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder 93ed44e08726 (Midwest Gun Works, LTGEN3MFDE: the FDE Gen 3-M closed, its black bolt carrier extension standing on its head end beside it, seen from in front and 17 degrees above (its top end's rim an ellipse 0.30 of its width); 1500 px)","scaleRef":"its length from the first shoulder's plane (row 576) to its head end's plane (841), 265 px, as .added_length: what it fills between the carrier and the buffer (the patent: \"This extension in length can compensate for the length added to the rifle by the addition of the folding stock adapter 100\"): 203.8 px/in along it, and 213.6 px/in across (its lengths foreshortened by cos 17.4 degrees)","method":"its silhouette's width row by row (luminance under 200), its axis fitted through the rows' middles (2.3 degrees off upright) and the widths taken square to it; a plane is the row where the silhouette reaches that section's full width; the pilot 128 px","via":"harvest"},"note":"152 px"},{"id":"mgw-black","value":0.723,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder af70d3e9c54e (Midwest Gun Works, 99312_Z: the black Gen 3-M closed, its bolt carrier extension standing on its head end beside it, seen from in front and 28 degrees above (its top end's rim an ellipse 0.47 of its width); 1500 px)","scaleRef":"its length from the first shoulder's plane (row 516) to its head end's plane (777), 261 px, as .added_length: 200.8 px/in along it, and 228.2 px/in across (cos 28.3 degrees)","method":"as the FDE photo's (its axis 4.4 degrees off upright); the pilot 140 px","via":"harvest"},"note":"165 px"}],"adopt":{"from":"mgw-fde","reason":"Nearer side-on; the two agree within their ±."}},"ext_collar_length":{"label":"Bolt carrier extension: the collar, along","kind":"length","measurements":[{"id":"mgw-fde","value":0.093,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder 93ed44e08726 (Midwest Gun Works, LTGEN3MFDE: the FDE Gen 3-M closed, its black bolt carrier extension standing on its head end beside it, seen from in front and 17 degrees above (its top end's rim an ellipse 0.30 of its width); 1500 px)","scaleRef":"its length from the first shoulder's plane (row 576) to its head end's plane (841), 265 px, as .added_length: what it fills between the carrier and the buffer (the patent: \"This extension in length can compensate for the length added to the rifle by the addition of the folding stock adapter 100\"): 203.8 px/in along it, and 213.6 px/in across (its lengths foreshortened by cos 17.4 degrees)","method":"its silhouette's width row by row (luminance under 200), its axis fitted through the rows' middles (2.3 degrees off upright) and the widths taken square to it; a plane is the row where the silhouette reaches that section's full width; the pilot 128 px","via":"harvest"},"note":"rows 576 to 595, where its width begins to fall (the front of its lower face's rim)"},{"id":"mgw-black","value":0.12,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder af70d3e9c54e (Midwest Gun Works, 99312_Z: the black Gen 3-M closed, its bolt carrier extension standing on its head end beside it, seen from in front and 28 degrees above (its top end's rim an ellipse 0.47 of its width); 1500 px)","scaleRef":"its length from the first shoulder's plane (row 516) to its head end's plane (777), 261 px, as .added_length: 200.8 px/in along it, and 228.2 px/in across (cos 28.3 degrees)","method":"as the FDE photo's (its axis 4.4 degrees off upright); the pilot 140 px","via":"harvest"},"note":"rows 516 to 540"}],"adopt":{"from":"mgw-fde","reason":"Nearer side-on; the two agree within their ±."}},"ext_neck_d":{"label":"Bolt carrier extension: the neck behind the collar, across","kind":"length","measurements":[{"id":"mgw-fde","value":0.468,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder 93ed44e08726 (Midwest Gun Works, LTGEN3MFDE: the FDE Gen 3-M closed, its black bolt carrier extension standing on its head end beside it, seen from in front and 17 degrees above (its top end's rim an ellipse 0.30 of its width); 1500 px)","scaleRef":"its length from the first shoulder's plane (row 576) to its head end's plane (841), 265 px, as .added_length: what it fills between the carrier and the buffer (the patent: \"This extension in length can compensate for the length added to the rifle by the addition of the folding stock adapter 100\"): 203.8 px/in along it, and 213.6 px/in across (its lengths foreshortened by cos 17.4 degrees)","method":"its silhouette's width row by row (luminance under 200), its axis fitted through the rows' middles (2.3 degrees off upright) and the widths taken square to it; a plane is the row where the silhouette reaches that section's full width; the pilot 128 px","via":"harvest"},"note":"100 px"},{"id":"mgw-black","value":0.469,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder af70d3e9c54e (Midwest Gun Works, 99312_Z: the black Gen 3-M closed, its bolt carrier extension standing on its head end beside it, seen from in front and 28 degrees above (its top end's rim an ellipse 0.47 of its width); 1500 px)","scaleRef":"its length from the first shoulder's plane (row 516) to its head end's plane (777), 261 px, as .added_length: 200.8 px/in along it, and 228.2 px/in across (cos 28.3 degrees)","method":"as the FDE photo's (its axis 4.4 degrees off upright); the pilot 140 px","via":"harvest"},"note":"107 px"}],"adopt":{"from":"mgw-fde","reason":"Nearer side-on; the two agree."}},"ext_neck_length":{"label":"Bolt carrier extension: the neck, along (to where it flares)","kind":"length","measurements":[{"id":"mgw-fde","value":0.206,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder 93ed44e08726 (Midwest Gun Works, LTGEN3MFDE: the FDE Gen 3-M closed, its black bolt carrier extension standing on its head end beside it, seen from in front and 17 degrees above (its top end's rim an ellipse 0.30 of its width); 1500 px)","scaleRef":"its length from the first shoulder's plane (row 576) to its head end's plane (841), 265 px, as .added_length: what it fills between the carrier and the buffer (the patent: \"This extension in length can compensate for the length added to the rifle by the addition of the folding stock adapter 100\"): 203.8 px/in along it, and 213.6 px/in across (its lengths foreshortened by cos 17.4 degrees)","method":"its silhouette's width row by row (luminance under 200), its axis fitted through the rows' middles (2.3 degrees off upright) and the widths taken square to it; a plane is the row where the silhouette reaches that section's full width; the pilot 128 px","via":"harvest"},"note":"rows 595 to 637"},{"id":"mgw-black","value":0.194,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder af70d3e9c54e (Midwest Gun Works, 99312_Z: the black Gen 3-M closed, its bolt carrier extension standing on its head end beside it, seen from in front and 28 degrees above (its top end's rim an ellipse 0.47 of its width); 1500 px)","scaleRef":"its length from the first shoulder's plane (row 516) to its head end's plane (777), 261 px, as .added_length: 200.8 px/in along it, and 228.2 px/in across (cos 28.3 degrees)","method":"as the FDE photo's (its axis 4.4 degrees off upright); the pilot 140 px","via":"harvest"},"note":"rows 540 to 579"}],"adopt":{"from":"mgw-fde","reason":"Nearer side-on; the two agree."}},"ext_flare_length":{"label":"Bolt carrier extension: the cone from the neck to the body, along","kind":"length","measurements":[{"id":"mgw-fde","value":0.206,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder 93ed44e08726 (Midwest Gun Works, LTGEN3MFDE: the FDE Gen 3-M closed, its black bolt carrier extension standing on its head end beside it, seen from in front and 17 degrees above (its top end's rim an ellipse 0.30 of its width); 1500 px)","scaleRef":"its length from the first shoulder's plane (row 576) to its head end's plane (841), 265 px, as .added_length: what it fills between the carrier and the buffer (the patent: \"This extension in length can compensate for the length added to the rifle by the addition of the folding stock adapter 100\"): 203.8 px/in along it, and 213.6 px/in across (its lengths foreshortened by cos 17.4 degrees)","method":"its silhouette's width row by row (luminance under 200), its axis fitted through the rows' middles (2.3 degrees off upright) and the widths taken square to it; a plane is the row where the silhouette reaches that section's full width; the pilot 128 px","via":"harvest"},"note":"rows 637 to 679"},{"id":"mgw-black","value":0.209,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder af70d3e9c54e (Midwest Gun Works, 99312_Z: the black Gen 3-M closed, its bolt carrier extension standing on its head end beside it, seen from in front and 28 degrees above (its top end's rim an ellipse 0.47 of its width); 1500 px)","scaleRef":"its length from the first shoulder's plane (row 516) to its head end's plane (777), 261 px, as .added_length: 200.8 px/in along it, and 228.2 px/in across (cos 28.3 degrees)","method":"as the FDE photo's (its axis 4.4 degrees off upright); the pilot 140 px","via":"harvest"},"note":"rows 579 to 621"}],"adopt":{"from":"mgw-fde","reason":"Nearer side-on; the two agree."}},"ext_body_d":{"label":"Bolt carrier extension: the body, across","kind":"length","measurements":[{"id":"mgw-fde","value":0.714,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder 93ed44e08726 (Midwest Gun Works, LTGEN3MFDE: the FDE Gen 3-M closed, its black bolt carrier extension standing on its head end beside it, seen from in front and 17 degrees above (its top end's rim an ellipse 0.30 of its width); 1500 px)","scaleRef":"its length from the first shoulder's plane (row 576) to its head end's plane (841), 265 px, as .added_length: what it fills between the carrier and the buffer (the patent: \"This extension in length can compensate for the length added to the rifle by the addition of the folding stock adapter 100\"): 203.8 px/in along it, and 213.6 px/in across (its lengths foreshortened by cos 17.4 degrees)","method":"its silhouette's width row by row (luminance under 200), its axis fitted through the rows' middles (2.3 degrees off upright) and the widths taken square to it; a plane is the row where the silhouette reaches that section's full width; the pilot 128 px","via":"harvest"},"note":"152.5 px"},{"id":"mgw-black","value":0.71,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder af70d3e9c54e (Midwest Gun Works, 99312_Z: the black Gen 3-M closed, its bolt carrier extension standing on its head end beside it, seen from in front and 28 degrees above (its top end's rim an ellipse 0.47 of its width); 1500 px)","scaleRef":"its length from the first shoulder's plane (row 516) to its head end's plane (777), 261 px, as .added_length: 200.8 px/in along it, and 228.2 px/in across (cos 28.3 degrees)","method":"as the FDE photo's (its axis 4.4 degrees off upright); the pilot 140 px","via":"harvest"},"note":"162 px"}],"adopt":{"from":"mgw-fde","reason":"Nearer side-on; the two agree."},"note":"A darker band round its lower part in both photos (an O-ring or another finish, flush: the silhouette doesn't change there) isn't drawn."},"ext_body_length":{"label":"Bolt carrier extension: the body, along","kind":"length","measurements":[{"id":"mgw-fde","value":0.25,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder 93ed44e08726 (Midwest Gun Works, LTGEN3MFDE: the FDE Gen 3-M closed, its black bolt carrier extension standing on its head end beside it, seen from in front and 17 degrees above (its top end's rim an ellipse 0.30 of its width); 1500 px)","scaleRef":"its length from the first shoulder's plane (row 576) to its head end's plane (841), 265 px, as .added_length: what it fills between the carrier and the buffer (the patent: \"This extension in length can compensate for the length added to the rifle by the addition of the folding stock adapter 100\"): 203.8 px/in along it, and 213.6 px/in across (its lengths foreshortened by cos 17.4 degrees)","method":"its silhouette's width row by row (luminance under 200), its axis fitted through the rows' middles (2.3 degrees off upright) and the widths taken square to it; a plane is the row where the silhouette reaches that section's full width; the pilot 128 px","via":"harvest"},"note":"rows 679 to 730, where its width begins to fall to the stem's"},{"id":"mgw-black","value":0.269,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder af70d3e9c54e (Midwest Gun Works, 99312_Z: the black Gen 3-M closed, its bolt carrier extension standing on its head end beside it, seen from in front and 28 degrees above (its top end's rim an ellipse 0.47 of its width); 1500 px)","scaleRef":"its length from the first shoulder's plane (row 516) to its head end's plane (777), 261 px, as .added_length: 200.8 px/in along it, and 228.2 px/in across (cos 28.3 degrees)","method":"as the FDE photo's (its axis 4.4 degrees off upright); the pilot 140 px","via":"harvest"},"note":"rows 621 to 675"}],"adopt":{"from":"mgw-fde","reason":"Nearer side-on; the two agree within their ±."}},"ext_stem_d":{"label":"Bolt carrier extension: the stem behind the body, across","kind":"length","measurements":[{"id":"mgw-fde","value":0.48,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder 93ed44e08726 (Midwest Gun Works, LTGEN3MFDE: the FDE Gen 3-M closed, its black bolt carrier extension standing on its head end beside it, seen from in front and 17 degrees above (its top end's rim an ellipse 0.30 of its width); 1500 px)","scaleRef":"its length from the first shoulder's plane (row 576) to its head end's plane (841), 265 px, as .added_length: what it fills between the carrier and the buffer (the patent: \"This extension in length can compensate for the length added to the rifle by the addition of the folding stock adapter 100\"): 203.8 px/in along it, and 213.6 px/in across (its lengths foreshortened by cos 17.4 degrees)","method":"its silhouette's width row by row (luminance under 200), its axis fitted through the rows' middles (2.3 degrees off upright) and the widths taken square to it; a plane is the row where the silhouette reaches that section's full width; the pilot 128 px","via":"harvest"},"note":"102.5 px"},{"id":"mgw-black","value":0.469,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder af70d3e9c54e (Midwest Gun Works, 99312_Z: the black Gen 3-M closed, its bolt carrier extension standing on its head end beside it, seen from in front and 28 degrees above (its top end's rim an ellipse 0.47 of its width); 1500 px)","scaleRef":"its length from the first shoulder's plane (row 516) to its head end's plane (777), 261 px, as .added_length: 200.8 px/in along it, and 228.2 px/in across (cos 28.3 degrees)","method":"as the FDE photo's (its axis 4.4 degrees off upright); the pilot 140 px","via":"harvest"},"note":"107 px"}],"adopt":{"from":"mgw-fde","reason":"Nearer side-on; the two agree."}},"ext_stem_length":{"label":"Bolt carrier extension: the stem, along","kind":"length","measurements":[{"id":"mgw-fde","value":0.383,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder 93ed44e08726 (Midwest Gun Works, LTGEN3MFDE: the FDE Gen 3-M closed, its black bolt carrier extension standing on its head end beside it, seen from in front and 17 degrees above (its top end's rim an ellipse 0.30 of its width); 1500 px)","scaleRef":"its length from the first shoulder's plane (row 576) to its head end's plane (841), 265 px, as .added_length: what it fills between the carrier and the buffer (the patent: \"This extension in length can compensate for the length added to the rifle by the addition of the folding stock adapter 100\"): 203.8 px/in along it, and 213.6 px/in across (its lengths foreshortened by cos 17.4 degrees)","method":"its silhouette's width row by row (luminance under 200), its axis fitted through the rows' middles (2.3 degrees off upright) and the widths taken square to it; a plane is the row where the silhouette reaches that section's full width; the pilot 128 px","via":"harvest"},"note":"rows 730 to 808, where the head's flare begins"},{"id":"mgw-black","value":0.329,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder af70d3e9c54e (Midwest Gun Works, 99312_Z: the black Gen 3-M closed, its bolt carrier extension standing on its head end beside it, seen from in front and 28 degrees above (its top end's rim an ellipse 0.47 of its width); 1500 px)","scaleRef":"its length from the first shoulder's plane (row 516) to its head end's plane (777), 261 px, as .added_length: 200.8 px/in along it, and 228.2 px/in across (cos 28.3 degrees)","method":"as the FDE photo's (its axis 4.4 degrees off upright); the pilot 140 px","via":"harvest"},"note":"rows 675 to 741"}],"adopt":{"from":"mgw-fde","reason":"Nearer side-on, so less of its length rests on the elevation read; the black photo's reading stays beside it as a conflict."},"note":"The two photos differ by more than their ± here (the stem's ends read 0.054 in apart once each is scaled by its own length behind the shoulder): kept apart, not averaged. Each photo is from close by and from above, and its scale may change along the part."},"ext_head_d":{"label":"Bolt carrier extension: its head (the end the buffer bears on), across","kind":"length","measurements":[{"id":"mgw-fde","value":0.623,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder 93ed44e08726 (Midwest Gun Works, LTGEN3MFDE: the FDE Gen 3-M closed, its black bolt carrier extension standing on its head end beside it, seen from in front and 17 degrees above (its top end's rim an ellipse 0.30 of its width); 1500 px)","scaleRef":"its length from the first shoulder's plane (row 576) to its head end's plane (841), 265 px, as .added_length: what it fills between the carrier and the buffer (the patent: \"This extension in length can compensate for the length added to the rifle by the addition of the folding stock adapter 100\"): 203.8 px/in along it, and 213.6 px/in across (its lengths foreshortened by cos 17.4 degrees)","method":"its silhouette's width row by row (luminance under 200), its axis fitted through the rows' middles (2.3 degrees off upright) and the widths taken square to it; a plane is the row where the silhouette reaches that section's full width; the pilot 128 px","via":"harvest"},"note":"133 px at its widest, where the flare from the stem ends"},{"id":"mgw-black","value":0.609,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder af70d3e9c54e (Midwest Gun Works, 99312_Z: the black Gen 3-M closed, its bolt carrier extension standing on its head end beside it, seen from in front and 28 degrees above (its top end's rim an ellipse 0.47 of its width); 1500 px)","scaleRef":"its length from the first shoulder's plane (row 516) to its head end's plane (777), 261 px, as .added_length: 200.8 px/in along it, and 228.2 px/in across (cos 28.3 degrees)","method":"as the FDE photo's (its axis 4.4 degrees off upright); the pilot 140 px","via":"harvest"},"note":"139 px"}],"adopt":{"from":"mgw-fde","reason":"Nearer side-on; the two agree."}},"ext_head_length":{"label":"Bolt carrier extension: the head's flare and rim, along","kind":"length","measurements":[{"id":"mgw-fde","value":0.161,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder 93ed44e08726 (Midwest Gun Works, LTGEN3MFDE: the FDE Gen 3-M closed, its black bolt carrier extension standing on its head end beside it, seen from in front and 17 degrees above (its top end's rim an ellipse 0.30 of its width); 1500 px)","scaleRef":"its length from the first shoulder's plane (row 576) to its head end's plane (841), 265 px, as .added_length: what it fills between the carrier and the buffer (the patent: \"This extension in length can compensate for the length added to the rifle by the addition of the folding stock adapter 100\"): 203.8 px/in along it, and 213.6 px/in across (its lengths foreshortened by cos 17.4 degrees)","method":"its silhouette's width row by row (luminance under 200), its axis fitted through the rows' middles (2.3 degrees off upright) and the widths taken square to it; a plane is the row where the silhouette reaches that section's full width; the pilot 128 px","via":"harvest"},"note":"rows 808 to 841 (the flare to 835, its rim to the end's plane)"},{"id":"mgw-black","value":0.179,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder af70d3e9c54e (Midwest Gun Works, 99312_Z: the black Gen 3-M closed, its bolt carrier extension standing on its head end beside it, seen from in front and 28 degrees above (its top end's rim an ellipse 0.47 of its width); 1500 px)","scaleRef":"its length from the first shoulder's plane (row 516) to its head end's plane (777), 261 px, as .added_length: 200.8 px/in along it, and 228.2 px/in across (cos 28.3 degrees)","method":"as the FDE photo's (its axis 4.4 degrees off upright); the pilot 140 px","via":"harvest"},"note":"rows 741 to 777 (the flare to 768)"}],"adopt":{"from":"mgw-fde","reason":"Nearer side-on; the two agree."}},"bolt_head_d":{"label":"The hinge bolt's socket head, across (in a counterbore in the upper tab's top)","kind":"length","measurements":[{"id":"trex","value":0.317,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder 156bc8e73a87 (T.REX Arms' gallery, TAN-7945: the FDE adapter opened about 90 degrees, from above and in front; 3000 px)","scaleRef":"the upper tab's top rim in the same plane, 193 px across (columns 1452 to 1645), as .knuckle_d","method":"the black head's rim, 127 px across (columns 1485 to 1612), on a 3x crop; widths across the picture, which the view from above and in front doesn't foreshorten","via":"harvest"}}]},"bolt_counterbore_d":{"label":"The counterbore the hinge bolt's head sits in, across","kind":"length","measurements":[{"id":"trex","value":0.374,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/law-tactical-gen3m-folder 156bc8e73a87 (T.REX Arms, the FDE adapter opened, from above and in front; 3000 px)","scaleRef":"the upper tab's top rim, 193 px across, as .knuckle_d","method":"the tab's tan rim's inner edge, 150 px across (columns 1475 to 1625)","via":"harvest"}}]},"bolt_socket":{"label":"The hinge bolt's hex socket, across its flats","kind":"length","measurements":[{"id":"sheet","value":0.125,"unit":"in","pm":0.002,"stated":"Hinge Tension: A 1/8 Allen Wrench can be used to increase hinge tension by tightening the Hinge Screw (10).","source":{"type":"spec","publisher":"manufacturer","name":"Law Tactical, Generation 3-M AR Folding Stock Adapter instructions (no text layer: read from its pages as pictures), Maintenance","url":"https://www.arfoldingstock.com/img/GEN3-M_Instructions.pdf","retrieved":"2026-10-18","via":"harvest"},"note":"The key that turns it is 1/8 in: its socket is that across the flats. T.REX's photo has the socket some 60 px of the tab's 193 (0.15 in, across its corners)."}]},"bolt_head_recess":{"label":"How far the bolt's head stands under the upper tab's top","kind":"length","measurements":[{"id":"assumed","value":0.04,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: T.REX's photo from above shows the counterbore's wall dark above the head, so the head is below the rim; by how much isn't seen.","via":"harvest"}}]},"bolt_head_height":{"label":"The bolt's head, its height (and the counterbore's depth under it)","kind":"length","measurements":[{"id":"assumed","value":0.15,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view shows the head in profile; about half its width, as a socket head is.","via":"harvest"}}]},"bolt_socket_depth":{"label":"The bolt head's hex socket, its depth","kind":"length","measurements":[{"id":"assumed","value":0.08,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the socket's floor isn't seen.","via":"harvest"}}]}}},{"subject":"magpul-ctr","title":"Magpul CTR carbine stock, mil-spec","dimensions":{"length":{"label":"Overall length","kind":"length","measurements":[{"id":"magpul","value":7,"unit":"in","pm":0.05,"stated":"Length, max 7.0 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, CTR Carbine Stock - Mil-Spec (MAG310)","url":"https://magpul.com/ctr-carbine-stock-mil-spec.html","retrieved":"2026-10-01","via":"harvest"}},{"id":"big-tex","value":6.9,"unit":"in","stated":"Length, max 6.9 in.","source":{"type":"spec","publisher":"retailer","name":"Big Tex Ordnance, CTR Carbine Stock, Mil-Spec (Magpul's earlier table, copied)","url":"https://www.bigtexordnance.com/product/magpul-industries-ctr-carbine-stock-mil-spec-mil-spec-mag10/","retrieved":"2026-10-01","via":"harvest"}},{"id":"wing","value":6.9,"unit":"in","stated":"Length: 6.9\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Magpul CTR Stock (MAG310)","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/stocks-accessories/magpul-ctr-compact-type-restricted-stock-mil-spec/","retrieved":"2026-10-01","via":"harvest"}}],"adopt":{"from":"magpul","reason":"Magpul's current page. Retailers carry 6.9, Magpul's earlier figure; the oldest table (Operation Parts) gives the body with a plain butt cap as 6.60 and adds 0.30 for the rubber pad."}},"height":{"label":"Height","kind":"length","measurements":[{"id":"magpul","value":5.2,"unit":"in","stated":"Height, max 5.2 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, CTR Carbine Stock - Mil-Spec (MAG310)","url":"https://magpul.com/ctr-carbine-stock-mil-spec.html","retrieved":"2026-10-01","via":"harvest"}},{"id":"wing","value":5.2,"unit":"in","stated":"Height: 5.2\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Magpul CTR Stock (MAG310)","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/stocks-accessories/magpul-ctr-compact-type-restricted-stock-mil-spec/","retrieved":"2026-10-01","via":"harvest"}}],"adopt":{"from":"magpul","reason":"Manufacturer; the retailer repeats it."}},"width":{"label":"Width","kind":"length","measurements":[{"id":"magpul","value":1.7,"unit":"in","stated":"Width, max 1.7 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, CTR Carbine Stock - Mil-Spec (MAG310)","url":"https://magpul.com/ctr-carbine-stock-mil-spec.html","retrieved":"2026-10-01","via":"harvest"}},{"id":"wing","value":1.7,"unit":"in","stated":"Width: 1.7\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Magpul CTR Stock (MAG310)","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/stocks-accessories/magpul-ctr-compact-type-restricted-stock-mil-spec/","retrieved":"2026-10-01","via":"harvest"}}],"adopt":{"from":"magpul","reason":"Manufacturer; the retailer repeats it."}},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"magpul","value":8.9,"unit":"oz","stated":"Weight 8.9 oz.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, CTR Carbine Stock - Mil-Spec (MAG310)","url":"https://magpul.com/ctr-carbine-stock-mil-spec.html","retrieved":"2026-10-01","via":"harvest"}},{"id":"big-tex","value":8.8,"unit":"oz","stated":"Weight 8.8 oz.","source":{"type":"spec","publisher":"retailer","name":"Big Tex Ordnance, CTR Carbine Stock, Mil-Spec (Magpul's earlier table, copied)","url":"https://www.bigtexordnance.com/product/magpul-industries-ctr-carbine-stock-mil-spec-mil-spec-mag10/","retrieved":"2026-10-01","via":"harvest"}},{"id":"wing","value":9.07,"unit":"oz","stated":"Weight: 9.07 oz.","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Magpul CTR Stock (MAG310)","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/stocks-accessories/magpul-ctr-compact-type-restricted-stock-mil-spec/","retrieved":"2026-10-01","via":"harvest"}}],"adopt":{"from":"magpul","reason":"Magpul's current page. Retailers say 8.8 (Magpul's earlier figure) and 9.07."}},"weight_with_extension":{"label":"Weight with a receiver extension (the maker's own tube)","kind":"mass","measurements":[{"id":"magpul","value":12.7,"unit":"oz","stated":"Weight, w/ receiver extension ~12.7 oz","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, CTR Carbine Stock - Mil-Spec (MAG310)","url":"https://magpul.com/ctr-carbine-stock-mil-spec.html","retrieved":"2026-10-01","via":"harvest"}},{"id":"big-tex","value":12.8,"unit":"oz","stated":"Weight, w/ receiver extension 12.8 oz","source":{"type":"spec","publisher":"retailer","name":"Big Tex Ordnance, CTR Carbine Stock, Mil-Spec (Magpul's earlier table, copied)","url":"https://www.bigtexordnance.com/product/magpul-industries-ctr-carbine-stock-mil-spec-mil-spec-mag10/","retrieved":"2026-10-01","via":"harvest"}}],"adopt":{"from":"magpul","reason":"Magpul's current page; the earlier table's figure is 0.1 oz more."},"note":"Not used by the build, which weighs its own buffer kit. Kept because it says what Magpul takes a mil-spec carbine receiver extension to weigh: 3.8 oz (12.7 less 8.9), or 4.0 by the earlier table."},"lop_collapsed":{"label":"Length of pull, collapsed (the maker's reference rifle)","kind":"length","measurements":[{"id":"magpul","value":10.3,"unit":"in","stated":"LOP, M4 Collapsed ~10.3 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, CTR Carbine Stock - Mil-Spec (MAG310)","url":"https://magpul.com/ctr-carbine-stock-mil-spec.html","retrieved":"2026-10-01","via":"harvest"}},{"id":"big-tex","value":10.5,"unit":"in","stated":"LOP, M4 Collapsed ~10.5 in.","source":{"type":"spec","publisher":"retailer","name":"Big Tex Ordnance, CTR Carbine Stock, Mil-Spec (Magpul's earlier table, copied)","url":"https://www.bigtexordnance.com/product/magpul-industries-ctr-carbine-stock-mil-spec-mil-spec-mag10/","retrieved":"2026-10-01","via":"harvest"}},{"id":"scheels","value":10.7,"unit":"in","stated":"LOP M4 Collapsed: ~10.7 in.","source":{"type":"spec","publisher":"retailer","name":"Scheels, Magpul CTR Carbine Stock - Mil-Spec","url":"https://www.scheels.com/p/magpul-ctr-carbine-stock---mil-spec/873750-MAG310/","retrieved":"2026-10-01","via":"harvest"}}],"adopt":{"from":"magpul","reason":"Magpul's current page. Retailers carry two earlier figures of Magpul's, 0.2 and 0.4 in longer."},"note":"Magpul has published three figures for it with the rubber pad, the same three as for the MOE Carbine (10.7, 10.5, 10.3), and a fourth without: Operation Parts carries the oldest table, 10.1 in with a plain butt cap, \"Rubber Butt-Pad adds 0.30 in. LOP\". It isn't what seats the stock (butt_behind_pin_pos1)."},"lop_extended":{"label":"Length of pull, extended (the maker's reference rifle)","kind":"length","measurements":[{"id":"magpul","value":13.6,"unit":"in","stated":"LOP, M4 Extended ~13.6 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, CTR Carbine Stock - Mil-Spec (MAG310)","url":"https://magpul.com/ctr-carbine-stock-mil-spec.html","retrieved":"2026-10-01","via":"harvest"}},{"id":"big-tex","value":13.8,"unit":"in","stated":"LOP, M4 Extended ~13.8 in.","source":{"type":"spec","publisher":"retailer","name":"Big Tex Ordnance, CTR Carbine Stock, Mil-Spec (Magpul's earlier table, copied)","url":"https://www.bigtexordnance.com/product/magpul-industries-ctr-carbine-stock-mil-spec-mil-spec-mag10/","retrieved":"2026-10-01","via":"harvest"}},{"id":"scheels","value":14,"unit":"in","pm":0.05,"stated":"LOP M4 Extended: ~14.0 in.","source":{"type":"spec","publisher":"retailer","name":"Scheels, Magpul CTR Carbine Stock - Mil-Spec","url":"https://www.scheels.com/p/magpul-ctr-carbine-stock---mil-spec/873750-MAG310/","retrieved":"2026-10-01","via":"harvest"}}],"adopt":{"from":"magpul","reason":"Magpul's current page; the earlier figures move with the collapsed ones (the range is 3.3 in each time)."}},"lop_range":{"label":"Length-of-pull adjustment range","kind":"length","measurements":[{"id":"magpul","value":3.3,"unit":"in","stated":"LOP Adjustment Range 3.3 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, CTR Carbine Stock - Mil-Spec (MAG310)","url":"https://magpul.com/ctr-carbine-stock-mil-spec.html","retrieved":"2026-10-01","via":"harvest"}},{"id":"lop","value":3.3,"unit":"in","source":{"type":"derived","expr":"{.lop_extended} - {.lop_collapsed}","via":"harvest"}}],"adopt":{"from":"magpul","reason":"Stated; the two lengths of pull differ by it."}},"buttpad_thickness":{"label":"Rubber butt pad, thickness","kind":"length","measurements":[{"id":"magpul","value":0.3,"unit":"in","stated":"Removable 0.3\" Rubber Butt-Pad offers an anti-slip surface and increases impact protection","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, CTR Carbine Stock - Mil-Spec (MAG310)","url":"https://magpul.com/ctr-carbine-stock-mil-spec.html","retrieved":"2026-10-01","via":"harvest"}}]},"tube_axis_below_top":{"label":"Tube axis below the stock's top edge (at its highest)","kind":"length","measurements":[{"id":"installed","value":0.72,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-ctr 3a0618e87fb5 (Magpul: the CTR on a rifle, right side, close, 1200 px)","scaleRef":"the stock's own length, 829.1 px from the butt pad's rearmost point to the front face for Magpul's 7.0 in: 118.4 px/in (its height, 619 px for 5.2 in, gives 119.1). Not the tube's diameter: it reads 132.8 px, 1.12 in","method":"the bare tube's axis, midway between its limbs (row 405.0 over columns 1090 to 1120), below the cheek's top line carried forward along its own slope (325.7 there): 79.3 px; and the hump stands 6.2 px above that line (318.4 at column 160): 85.5 px","via":"harvest"}},{"id":"installed-rifle","value":0.695,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-ctr c32d71230ac5 (Magpul: the CTR on a whole rifle, straight right side, 1200 x 1200)","scaleRef":"the receiver's Picatinny rail, nine slots at 12.90 px (std.picatinny.slot_pitch): 32.6 px/in; the pins give 32.7","method":"the exposed tube's axis, midway between its limbs (row 568.5 over columns 288 to 306; the rifle lies level), below the cheek's top line (547.5): 21.0 px, 0.644 in. The hump isn't resolved at this size: the traced outline's 0.051 in is added","via":"harvest"}}],"adopt":{"from":"installed","reason":"The tube itself in the stock at three times the resolution; the whole-rifle photo agrees within the two ±. The MOE Carbine reads 0.706 the same way."},"note":"The highest point is the hump at the butt, 0.05 in above the cheek's top line (the side outline's y = 0), as on the MOE Carbine."},"frame_width":{"label":"Width of the frame below the tube: the upright, the strut and the brace","kind":"length","measurements":[{"id":"moe-carbine","value":0.69,"unit":"in","pm":0.08,"source":{"type":"derived","expr":"{magpul-moe-carbine.frame_width}","via":"harvest"}}],"note":"No end view of the CTR was found. The MOE Carbine's, from its design patent, stands in: the same A-frame by Magpul's description and published sizes."},"lock_pin_behind_front":{"label":"Lock pin behind the stock's front face","kind":"length","measurements":[{"id":"installed","value":2.34,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/magpul-ctr 3a0618e87fb5 (Magpul: the CTR on a rifle, right side, close, 1200 px)","scaleRef":"the stock's own length, 829.1 px for Magpul's 7.0 in: 118.4 px/in (its height gives 119.1)","method":"the pin's round head (columns 631 to 656) and the shaft under it, centred 277.8 px behind the front face (column 921.5)","via":"harvest"}}],"note":"The steel pin the latch draws out of the receiver extension's holes; its lower end shows in the slot beside the latch. The MOE Carbine's stands 2.37 in behind its front: the same latch, so at one hole the two stocks' fronts are in one place."},"butt_behind_pin_pos4":{"label":"Butt behind the takedown pin as Magpul photographed it: three steps out (position 4)","kind":"length","measurements":[{"id":"installed","value":10.456,"unit":"in","pm":0.084,"source":{"type":"photo","photo":"references/magpul-ctr c32d71230ac5 (Magpul: the CTR on a whole rifle, straight right side, 1200 x 1200)","scaleRef":"frame from the reviewed holes takedown, pivot, selector (32.7 px/in, rms 0.002 in over 3 points)","method":"−x of the fitted profile's origin of the traced outline (tools/trace.py); the traced side outline's origin (the butt pad's rearmost point), fitted by rotation and translation at the outline's own scale to the stock's edges against the background","via":"harvest"}}],"note":"Which position it is in: its front face stands 1.91 in behind the castle nut here and 1.98 in in Magpul's closer view (3a0618e87fb5): three steps (3 × 0.66). The same rifle and tube as the MOE Carbine's photos, where that stock is two steps out."},"butt_behind_pin_pos1":{"label":"Butt behind the takedown pin at position 1 (collapsed), on a carbine receiver extension","kind":"length","measurements":[{"id":"from-moe","value":8.726,"unit":"in","pm":0.09,"source":{"type":"derived","expr":"{magpul-moe-carbine.butt_behind_pin_pos1} - {magpul-moe-carbine.length} + {magpul-moe-carbine.lock_pin_behind_front} - {.lock_pin_behind_front} + {.length}","via":"harvest"},"note":"The MOE Carbine's front at the same hole, moved by the difference between the two lock pins' places, plus this stock's length. ± is the MOE Carbine's seat's and the two pins'."},{"id":"holes","value":8.839,"unit":"in","pm":0.07,"source":{"type":"derived","expr":"{bcm-receiver-extension.tube_front_behind_pin} + {bcm-receiver-extension.tube_length} - {bcm-receiver-extension.position_hole_rear_from_rear} - 5 * {bcm-receiver-extension.position_step} - {.lock_pin_behind_front} + {.length}","via":"harvest"},"note":"The lock pin in the tube's front hole. ± for the hole's place (0.03), the tube's seat (0.02) and the pin's (0.04), and for the tube's length, which is a generic figure."},{"id":"installed","value":8.476,"unit":"in","pm":0.084,"source":{"type":"derived","expr":"{.butt_behind_pin_pos4} - 3 * {.lop_range} / 5","via":"harvest"},"note":"Three of the five steps of Magpul's 3.3 in range. ± is the photo's alone."}],"adopt":{"from":"from-moe","reason":"Its own photo, three steps out, would put the stock's front inside the castle nut. The MOE Carbine's seat, from the same rifle one step nearer, clears the nut, the two stocks share their latch, and the tube's holes agree with it within the two ±."},"note":"Its own photo, less its three steps, puts its front face 0.16 in inside the castle nut (bcm-castle-nut.rear_face_behind_pin): three steps carry the photo's ± and any difference between that rifle's tube and 0.66 in a hole, and a stock has play in each hole (Magpul's two photos of each stock differ by 0.1 in on where it sits behind the nut). So it is seated with the MOE Carbine, measured the same way one step nearer: the two stocks' lock pins stand the same distance behind their fronts (2.34 and 2.37 in), and Magpul lists the same lengths of pull for both in every revision."},"bore_diameter":{"label":"The bore for the receiver extension (the MOE Carbine's, standing in)","kind":"length","measurements":[{"id":"moe-carbine","value":1.158,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{magpul-moe-carbine.bore_diameter}","via":"harvest"}}],"note":"No end view of the CTR was found. The MOE Carbine's bore, read on its design patent, stands in, as its section and its frame's width do: both are Magpul's Mil-Spec carbine stocks, for the same tube (std.receiver_extension.milspec_od, 1.148)."},"rail_channel_width":{"label":"Width of the channel under the bore, for the receiver extension's indexing rail","kind":"length","measurements":[{"id":"moe-carbine","value":0.49,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{magpul-moe-carbine.rail_channel_width}","via":"harvest"}}],"note":"Not read from this stock: the MOE Carbine's, which is the mil-spec tube's rail at its own width, with nothing to spare (no clearance is known)."},"rail_channel_floor_below_axis":{"label":"Floor of the indexing rail's channel, below the tube axis","kind":"length","measurements":[{"id":"moe-carbine","value":0.874,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{magpul-moe-carbine.rail_channel_floor_below_axis}","via":"harvest"}}],"note":"Not read from this stock: the MOE Carbine's, which is where the mil-spec tube's rail ends below its axis, with nothing to spare (no clearance is known)."}}},{"subject":"magpul-mbus-3-front","title":"Magpul MBUS 3 Sight – Front (MAG1166)","dimensions":{"weight":{"label":"Weight (with its screw)","kind":"mass","measurements":[{"id":"magpul","value":25,"unit":"g","stated":"Weight, w/ hardware 25 g","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MBUS 3 Sight – Front (MAG1166)","url":"https://magpul.com/mbus-3-sight-front.html","retrieved":"2026-10-05","via":"harvest"}},{"id":"features","value":0.88,"unit":"oz","stated":"Compact (0.47ʺ tall when folded; 1.38ʺ wide) and lightweight (0.88 oz) polymer deigned for mobility, durability, and reliability","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MBUS 3 Sight – Front (MAG1166)","url":"https://magpul.com/mbus-3-sight-front.html","retrieved":"2026-10-05","via":"harvest"}},{"id":"trex","value":0.9,"unit":"oz","stated":"Weight 0.9 ounces (front only) 1.9 ounces (front and rear)","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, Magpul MBUS 3 Sight - Front, Technical Specifications (the source of its rows unstated)","url":"https://www.trex-arms.com/store/magpul-mbus-3-sight-front-865852","retrieved":"2026-10-05","via":"harvest"}}],"adopt":{"from":"magpul","reason":"The maker's technical-specification row, which says what it includes; its feature list's 0.88 oz is the same figure in ounces."},"note":"Dirty Bird's \"Weight 3 oz\" (beside \"2.13 × 0.65 × 3 in\") and KYGunCo's \"1 lb\" are shipping figures and aren't recorded."},"length":{"label":"Length along the rail (folded, where it folds)","kind":"length","measurements":[{"id":"trex","value":2.13,"unit":"in","stated":"Length 2.13 inches","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, Magpul MBUS 3 Sight - Front, Technical Specifications (the source of its rows unstated)","url":"https://www.trex-arms.com/store/magpul-mbus-3-sight-front-865852","retrieved":"2026-10-05","via":"harvest"}},{"id":"dirtybird","value":2.13,"unit":"in","stated":"Dimensions 2.13 × 0.65 × 3 in","source":{"type":"spec","publisher":"retailer","name":"Dirty Bird Industries, Magpul MBUS Gen 3 Folding Front Sight - Black, Additional information","url":"https://dirtybirdusa.com/products/magpul-mbus-gen-3-folding-front-sight-black/","retrieved":"2026-10-05","via":"harvest"},"note":"The same two figures as T.REX's length and total height, beside a 3 in and a 3 oz that are a parcel's: probably one origin, not a second measurement."},{"id":"photo","value":2.15,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-mbus-3-front c823bae5d9f5 (Magpul's gallery image 04.1, \"Side view of stowed MBUS 3 Front Sight on railed forend\", in Impact Guns' 1500 px copy; Magpul's own 1200 px file, 5cbe636d7387, reads the same)","scaleRef":"the handguard's rail teeth behind the sight in the same image (calibrate.py rail: 7 slots, residual 0.0009 in rms; 118.8 px/slot over the four nearest the sight, 301.5 px/in in the rail's mid-plane)","method":"the silhouette's ends at the 50% level: the wings' tips (u 514.4) to the base's front (u 1171.7), 657.3 px = 2.180 in in the rail's mid-plane; the ends stand 0.3 to 0.6 in nearer the lens than that plane (the near wing, the near cheek) and read 0.6 to 2% long for a lens 80 to 25 in away, which isn't known: 2.15, and the ± covers that range, the pitch's ± 0.5% and the edges (the 1200 px file: 526.3 px at 95.1 px/slot, 2.180)","via":"harvest"}}],"adopt":{"from":"trex","reason":"A published figure; the maker's own photo of the sight folded on a rail, scaled by the rail's teeth, agrees within its ±. Dirty Bird's row is the same number."},"note":"Folded, the arm lies back from its hinge along the rail (the installation sheet: \"slide it onto the rail with Sight Arm to the rear\"; \"To stow sight, push down Sight Arm into flat position\"): the base's front end to the wings' tips. Magpul states no length. This figure sets the scale of the patent's figures (the subject's header). Standing it is half as long (length_up)."},"width":{"label":"Width","kind":"length","measurements":[{"id":"magpul","value":1.38,"unit":"in","stated":"It stows at just .47” tall and 1.38” wide on your M1913 picatinny rail","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MBUS 3 Sight – Front (MAG1166)","url":"https://magpul.com/mbus-3-sight-front.html","retrieved":"2026-10-05","via":"harvest"},"note":"Also in its feature list: \"Compact (0.47ʺ tall when folded; 1.38ʺ wide)\". T.REX ARMS, Wing Tactical, Dirty Bird, Midwest Gun Works, Mile High, Alexander's and AR15Discounts repeat it."},{"id":"sellers","value":1.15,"unit":"in","stated":"Significantly reduced in size from the MBUS, it sits at just 0.44” high when folded and 1.15” at its widest point.","source":{"type":"spec","publisher":"retailer","name":"Scheels, Magpul MBUS 3 Front Sight (873750-MAG1166): the maker's older copy, word for word on Right To Bear, KYGunCo, Impact Guns and GRITR Outdoors too; Primary Arms: \"folds down to just .44\" high and 1.15\" wide so it sits on slimmer rails without overhanging\"","url":"https://www.scheels.com/p/magpul-mbus-3-front-sight/873750-MAG1166/","retrieved":"2026-10-05","via":"harvest"}},{"id":"patent","value":1.299,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-mbus-3-front 21c2b9876c1b (US D1,010,056 S (Magpul, 'Gun sight'), FIG. 4 rear elevation; the patent office's copy, page 6, 300 dpi)","scaleRef":"the patent's own folded length as .length (2.13 in): in FIG. 2 and FIG. 3 the base's front end to the hinge's axis, 792.0 px, plus the hinge's axis to the wings' top, 1165.4 px (the arm a quarter turn back about its hinge), 1957.4 px: 919.0 px/in; FIG. 4, FIG. 5 and FIG. 7 are drawn at the same scale (their rows and lengths agree to a pixel)","method":"the boss's face (u 660.5, solid) to the screw head's (u 1854.5, in broken lines: the patent's environment): 1194 px; strokes' centres","via":"harvest"}},{"id":"photo","value":1.255,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-mbus-3-front 0933bc534c51 (Magpul's gallery image 03.1, \"Underside view of MBUS 3 Front Sight in stowed position\", in Impact Guns' 1500 px copy; Magpul's own 1200 px file is 2c3af1e179ed)","scaleRef":"the folded sight's own length in the same image, the wings' tips to the base's front end, 1326 px, as .length (2.13 in): 622.5 px/in. Seen from below, so the base is some 0.5 in nearer the lens than the arm's tip: sizes on the base read up to 2% large against that length","method":"the silhouette's widest rows, the boss's face to the screw head's: 781 px (Magpul's 1200 px file: 627 of 1061 px, the same 0.59 of the length). Its front view (ff4952671f93) has the same two faces 937 px apart where the cheeks are 843: 1.11 of the body, 1.27 in","via":"harvest"}}],"adopt":{"from":"magpul","reason":"The maker's own present figure for its product is kept as the published width, as the run's brief asks; it is in conflict with everything measured (the note), and the model is not built to it."},"note":"Three different sizes are in print or in the drawings, and they are kept apart. The maker's present page says 1.38 in. Its older copy, still on eight sellers' pages (Primary Arms, Scheels, Sportsman's Warehouse, Right To Bear, Rifle Supply, KYGunCo, Impact Guns, GRITR Outdoors), says 1.15 in \"at its widest point\": that is the body between its cheeks' outer faces (body_width, 1.143 by the patent at the length's scale). Across the round boss on its left and the screw's head on its right the patent has 1.30 (the head in broken lines) and Magpul's own photos 1.26 to 1.28. Nothing on file reproduces 1.38: at a scale that made the patent 1.38 wide it would be 2.26 in long, against T.REX's 2.13 and the rail photo's 2.15. The model is the patent's (1.27 across the boss and the head as photographed)."},"height":{"label":"Height above the rail's top, folded (a fixed sight: its height)","kind":"length","measurements":[{"id":"magpul","value":0.47,"unit":"in","stated":"Height above rail, stowed ~0.47 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MBUS 3 Sight – Front (MAG1166)","url":"https://magpul.com/mbus-3-sight-front.html","retrieved":"2026-10-05","via":"harvest"},"note":"Approximate by its own tilde. Elsewhere on the page: \"0.47ʺ tall when folded\", \"STOWED HEIGHT OF ONLY 0.47\"\"."},{"id":"trex","value":0.47,"unit":"in","stated":"Height 0.65 inches (total) 0.47 inches (above rail)","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, Magpul MBUS 3 Sight - Front, Technical Specifications (the source of its rows unstated)","url":"https://www.trex-arms.com/store/magpul-mbus-3-sight-front-865852","retrieved":"2026-10-05","via":"harvest"}},{"id":"sellers","value":0.44,"unit":"in","stated":"Significantly reduced in size from the MBUS, it sits at just 0.44” high when folded and 1.15” at its widest point.","source":{"type":"spec","publisher":"retailer","name":"Scheels, Magpul MBUS 3 Front Sight (873750-MAG1166): the maker's older copy, word for word on Right To Bear, KYGunCo, Impact Guns and GRITR Outdoors too; Primary Arms: \"folds down to just .44\" high and 1.15\" wide so it sits on slimmer rails without overhanging\"","url":"https://www.scheels.com/p/magpul-mbus-3-front-sight/873750-MAG1166/","retrieved":"2026-10-05","via":"harvest"}},{"id":"photo","value":0.46,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-mbus-3-front c823bae5d9f5 (Magpul's gallery image 04.1, the sight folded on a railed forend, right side, in Impact Guns' 1500 px copy; Magpul's own 1200 px file is 5cbe636d7387)","scaleRef":"the handguard's rail teeth in the same image (calibrate.py rail: 7 slots, 0.0009 in rms): 301.5 px/in in the rail's mid-plane near the sight","method":"above the line through the tops of the five clear teeth behind it (266 columns, 0.9 px rms): the highest point 138.7 px (at u 627, the post's end, and 138.2 at u 870, the latch's hinge end); the arm's and the base's flat top 131 to 134 px (0.444 in). The lens stands a little above the rail (the base's top face shows), which lifts a far edge by up to 0.01 in: inside the ±","via":"harvest"}},{"id":"patent","value":0.431,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-mbus-3-front c0c71839efcb (US D1,010,056 S (Magpul, 'Gun sight'), FIG. 2 left elevation; the patent office's copy, page 4, 300 dpi)","scaleRef":"the patent's own folded length as .length (2.13 in): in FIG. 2 and FIG. 3 the base's front end to the hinge's axis, 792.0 px, plus the hinge's axis to the wings' top, 1165.4 px (the arm a quarter turn back about its hinge), 1957.4 px: 919.0 px/in; FIG. 4, FIG. 5 and FIG. 7 are drawn at the same scale (their rows and lengths agree to a pixel)","method":"the underside of the base's hinge block, which lies on the rail (row 2138.5; the rail's own top, in broken lines in FIG. 4, is row 2141.5), to the base's top edge (row 1742.5): 396 px. The arm folded reaches the same: its front face and its round end stand 193.3 px off the hinge's axis, which is 202.2 px above the rail: 395.5 px","via":"harvest"}}],"adopt":{"from":"magpul","reason":"The maker's row for exactly this dimension, approximate by its own tilde; its photo on a rail reads 0.46 to the highest point, within the two ±. The older 0.44 and the patent's 0.431 are the body's top, which is what the model draws."},"note":"From the rail's top (Magpul's row is \"Height above rail, stowed\"), to its highest point. The maker's older copy says 0.44, which is the body's top: the patent's base and folded arm both top out at 0.431, and the photo's at 0.444. What stands above that in the photo, to 0.46, is a small step at the hinge end of the base's latch and the sight post's end between the wings. The clamp reaches a further 0.25 below the rail's top (clamp_below_rail; height_total)."},"height_up":{"label":"Height above the rail's top, standing","kind":"length","measurements":[{"id":"patent","value":1.488,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-mbus-3-front c0c71839efcb (US D1,010,056 S (Magpul, 'Gun sight'), FIG. 2 left elevation; the patent office's copy, page 4, 300 dpi)","scaleRef":"the patent's own folded length as .length (2.13 in): in FIG. 2 and FIG. 3 the base's front end to the hinge's axis, 792.0 px, plus the hinge's axis to the wings' top, 1165.4 px (the arm a quarter turn back about its hinge), 1957.4 px: 919.0 px/in; FIG. 4, FIG. 5 and FIG. 7 are drawn at the same scale (their rows and lengths agree to a pixel)","method":"the underside of the base's hinge block (row 2138.5) to the wings' top (row 771.0; 771.5 in FIG. 3, 770.5 in FIG. 4 and FIG. 5): 1367.5 px; strokes' centres. The ± covers the length's last digit, the reading and a design patent's fidelity (this one's body, post and folded length sit within 1.6% of the published sizes)","via":"harvest"}}],"note":"To the wings' tops, the highest point: the sight post's tip is 0.1 in lower, between them. No published figure (Magpul: \"Standard AR sight height when deployed\")."},"sight_line_above_rail":{"label":"Sight line above the rail's top (the aperture's centre, the post's tip)","kind":"length","measurements":[{"id":"trex","value":1.41,"unit":"in","stated":"Centerline Height 1.41 inches","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, Magpul MBUS 3 Sight - Front, Technical Specifications (the source of its rows unstated)","url":"https://www.trex-arms.com/store/magpul-mbus-3-sight-front-865852","retrieved":"2026-10-05","via":"harvest"}},{"id":"patent","value":1.387,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-mbus-3-front 21c2b9876c1b (US D1,010,056 S (Magpul, 'Gun sight'), FIG. 4 rear elevation; the patent office's copy, page 6, 300 dpi)","scaleRef":"the patent's own folded length as .length (2.13 in): in FIG. 2 and FIG. 3 the base's front end to the hinge's axis, 792.0 px, plus the hinge's axis to the wings' top, 1165.4 px (the arm a quarter turn back about its hinge), 1957.4 px: 919.0 px/in; FIG. 4, FIG. 5 and FIG. 7 are drawn at the same scale (their rows and lengths agree to a pixel)","method":"the underside of the base's hinge block (row 2138.5) to the post's flat top (row 863.5, the same in FIG. 5): 1275 px. The ± is the post's travel as much as the reading: a drawing shows one setting","via":"harvest"}}],"adopt":{"from":"trex","reason":"The one published figure; the patent's post tip, drawn at one elevation setting, is within its travel of it."},"note":"The post's tip. Magpul gives no figure: \"Standard AR sight height for across-the-board compatibility\". T.REX's row doesn't say what its \"Centerline Height\" is measured to; the patent's post, at the height it is drawn (it screws up and down in its wheel), has its tip 0.023 in under it, so it is read as the sight line over the rail."},"clamp_length":{"label":"Clamp's length along the rail","kind":"length","measurements":[{"id":"patent","value":0.692,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-mbus-3-front 7557307d7b4e (US D1,010,056 S (Magpul, 'Gun sight'), FIG. 7 bottom view; the patent office's copy, page 9, 300 dpi)","scaleRef":"the patent's own folded length as .length (2.13 in): in FIG. 2 and FIG. 3 the base's front end to the hinge's axis, 792.0 px, plus the hinge's axis to the wings' top, 1165.4 px (the arm a quarter turn back about its hinge), 1957.4 px: 919.0 px/in; FIG. 4, FIG. 5 and FIG. 7 are drawn at the same scale (their rows and lengths agree to a pixel)","method":"the base's front face (u 764.5) to the step where its jaws end and the arm's legs begin (u 1402.5): 638 px; FIG. 2's cheek ends at u 1399 at the rail's level (634.5 px); the mean, 636.3 px","via":"harvest"}}],"note":"The base with its two jaws, front end to rear end: the hinge block behind it lies on the rail's top and has no jaws. The part frame's origin is at its middle."},"length_up":{"label":"Length along the rail, standing","kind":"length","measurements":[{"id":"patent","value":1.072,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-mbus-3-front c0c71839efcb (US D1,010,056 S (Magpul, 'Gun sight'), FIG. 2 left elevation; the patent office's copy, page 4, 300 dpi)","scaleRef":"the patent's own folded length as .length (2.13 in): in FIG. 2 and FIG. 3 the base's front end to the hinge's axis, 792.0 px, plus the hinge's axis to the wings' top, 1165.4 px (the arm a quarter turn back about its hinge), 1957.4 px: 919.0 px/in; FIG. 4, FIG. 5 and FIG. 7 are drawn at the same scale (their rows and lengths agree to a pixel)","method":"the base's front (u 764.5) to the arm's flat rear face (u 1749.25): 984.75 px; FIG. 3 (u 1750.0 to 765.0) 985.0; FIG. 7 985.0","via":"harvest"}}],"note":"The base's front end to the arm's rear face. The arm stands at the rear of the base (the installation sheet: \"slide it onto the rail with Sight Arm to the rear\")."},"clamp_below_rail":{"label":"Clamp's reach below the rail's top","kind":"length","measurements":[{"id":"patent","value":0.248,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/magpul-mbus-3-front c0c71839efcb (US D1,010,056 S (Magpul, 'Gun sight'), FIG. 2 left elevation; the patent office's copy, page 4, 300 dpi)","scaleRef":"the patent's own folded length as .length (2.13 in): in FIG. 2 and FIG. 3 the base's front end to the hinge's axis, 792.0 px, plus the hinge's axis to the wings' top, 1165.4 px (the arm a quarter turn back about its hinge), 1957.4 px: 919.0 px/in; FIG. 4, FIG. 5 and FIG. 7 are drawn at the same scale (their rows and lengths agree to a pixel)","method":"the underside of the base's hinge block (row 2138.5) to the jaws' lower edge (row 2366.5, the same in FIG. 3, FIG. 4 and FIG. 5): 228 px","via":"harvest"}}],"note":"The jaws' lower edge. The on-rail photo (c823bae5d9f5) has the cheek's lower edge 0.24 in under the tooth tops, dark on a dark handguard (± 0.015)."},"height_total":{"label":"Height folded, the clamp included","kind":"length","measurements":[{"id":"trex","value":0.65,"unit":"in","stated":"Height 0.65 inches (total) 0.47 inches (above rail)","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, Magpul MBUS 3 Sight - Front, Technical Specifications (the source of its rows unstated)","url":"https://www.trex-arms.com/store/magpul-mbus-3-sight-front-865852","retrieved":"2026-10-05","via":"harvest"}},{"id":"patent","value":0.679,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-mbus-3-front c0c71839efcb (US D1,010,056 S (Magpul, 'Gun sight'), FIG. 2 left elevation; the patent office's copy, page 4, 300 dpi)","scaleRef":"the patent's own folded length as .length (2.13 in): in FIG. 2 and FIG. 3 the base's front end to the hinge's axis, 792.0 px, plus the hinge's axis to the wings' top, 1165.4 px (the arm a quarter turn back about its hinge), 1957.4 px: 919.0 px/in; FIG. 4, FIG. 5 and FIG. 7 are drawn at the same scale (their rows and lengths agree to a pixel)","method":"the jaws' lower edge (row 2366.5) to the base's top edge (row 1742.5): 624 px","via":"harvest"}}],"adopt":{"from":"patent","reason":"Line art, whole and orthographic, which the model is built from; the on-rail photo reads 0.69 (0.444 over the tooth tops and 0.24 under them). T.REX's 0.65, which Dirty Bird's row repeats, is 0.03 under both, and what it spans isn't said."},"note":"The jaws' lower edge to the top. T.REX's total is 0.18 more than its height above the rail; the patent's jaws reach 0.248 under the rail's top and the photo's 0.24."},"hinge_behind_front":{"label":"Hinge's axis behind the base's front end","kind":"length","measurements":[{"id":"patent","value":0.862,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/magpul-mbus-3-front c0c71839efcb (US D1,010,056 S (Magpul, 'Gun sight'), FIG. 2 left elevation; the patent office's copy, page 4, 300 dpi)","scaleRef":"the patent's own folded length as .length (2.13 in): in FIG. 2 and FIG. 3 the base's front end to the hinge's axis, 792.0 px, plus the hinge's axis to the wings' top, 1165.4 px (the arm a quarter turn back about its hinge), 1957.4 px: 919.0 px/in; FIG. 4, FIG. 5 and FIG. 7 are drawn at the same scale (their rows and lengths agree to a pixel)","method":"the base's front (u 764.5) to the centre of the arm's round end (u 1556.8: circles fitted to its outer arc, r 193.4 px, its face, r 161.6, and the pin in broken lines, r 67.6, concentric within 0.6 px): 792.3 px; FIG. 3, 791.8; the mean","via":"harvest"}}],"note":"The arm turns about it. With the hinge's height and the standing height it makes the folded length: hinge_behind_front + (height_up − hinge_y) is the length, which is how the patent's scale was set."},"hinge_y":{"label":"Hinge's axis above the rail's top","kind":"length","measurements":[{"id":"patent","value":0.22,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/magpul-mbus-3-front c0c71839efcb (US D1,010,056 S (Magpul, 'Gun sight'), FIG. 2 left elevation; the patent office's copy, page 4, 300 dpi)","scaleRef":"the patent's own folded length as .length (2.13 in): in FIG. 2 and FIG. 3 the base's front end to the hinge's axis, 792.0 px, plus the hinge's axis to the wings' top, 1165.4 px (the arm a quarter turn back about its hinge), 1957.4 px: 919.0 px/in; FIG. 4, FIG. 5 and FIG. 7 are drawn at the same scale (their rows and lengths agree to a pixel)","method":"the underside of the base's hinge block (row 2138.5) to the centre of the arm's round end (row 1936.5; 1936.2 in FIG. 3): 202.2 px","via":"harvest"}}]},"knuckle_d":{"label":"Arm's round end: its diameter (the arm's thickness at its foot)","kind":"length","measurements":[{"id":"patent","value":0.421,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/magpul-mbus-3-front c0c71839efcb (US D1,010,056 S (Magpul, 'Gun sight'), FIG. 2 left elevation; the patent office's copy, page 4, 300 dpi)","scaleRef":"the patent's own folded length as .length (2.13 in): in FIG. 2 and FIG. 3 the base's front end to the hinge's axis, 792.0 px, plus the hinge's axis to the wings' top, 1165.4 px (the arm a quarter turn back about its hinge), 1957.4 px: 919.0 px/in; FIG. 4, FIG. 5 and FIG. 7 are drawn at the same scale (their rows and lengths agree to a pixel)","method":"the circle fitted to the round end's outer arc: r 193.4 px (192.8 to 194.0 over four fits in FIG. 2 and FIG. 3); the rear face stands 192.5 px behind its centre and the lower front face 193.3 px ahead","via":"harvest"}}],"note":"The arm's flat rear face and the front face of its lower half are both tangent to it: folded, the arm is this thick over the hinge."},"body_width":{"label":"Body's width, between its cheeks' outer faces","kind":"length","measurements":[{"id":"patent","value":1.143,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-mbus-3-front 21c2b9876c1b (US D1,010,056 S (Magpul, 'Gun sight'), FIG. 4 rear elevation; the patent office's copy, page 6, 300 dpi)","scaleRef":"the patent's own folded length as .length (2.13 in): in FIG. 2 and FIG. 3 the base's front end to the hinge's axis, 792.0 px, plus the hinge's axis to the wings' top, 1165.4 px (the arm a quarter turn back about its hinge), 1957.4 px: 919.0 px/in; FIG. 4, FIG. 5 and FIG. 7 are drawn at the same scale (their rows and lengths agree to a pixel)","method":"the cheeks' outer faces, u 732.5 and 1782.25: 1049.75 px; FIG. 5, 1050.0; FIG. 7, 1051.5; the mean, 1050.4 px","via":"harvest"}}],"note":"Without the boss and the screw's head. The sellers' older \"1.15 in at its widest point\" (width) is this within 0.007 in."},"bolt_x":{"label":"Cross bolt's axis ahead of the clamp's middle","kind":"length","measurements":[{"id":"patent","value":0.061,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/magpul-mbus-3-front c0c71839efcb (US D1,010,056 S (Magpul, 'Gun sight'), FIG. 2 left elevation; the patent office's copy, page 4, 300 dpi)","scaleRef":"the patent's own folded length as .length (2.13 in): in FIG. 2 and FIG. 3 the base's front end to the hinge's axis, 792.0 px, plus the hinge's axis to the wings' top, 1165.4 px (the arm a quarter turn back about its hinge), 1957.4 px: 919.0 px/in; FIG. 4, FIG. 5 and FIG. 7 are drawn at the same scale (their rows and lengths agree to a pixel)","method":"the centre of the boss's circles (u 1026.9; the screw head's in FIG. 3 mirrors it within 0.6 px) ahead of the middle of the base (u 764.5 to 1400.8: 1082.6): 55.7 px","via":"harvest"}}],"note":"The bolt lies in a rail slot (the installation sheet: \"Remove the 10-24 Dual Drive Screw from the MBUS 3 and slide it onto the rail\"), so this is where the sight sits against the slot it is in."},"bolt_below_rail":{"label":"Cross bolt's axis below the rail's top","kind":"length","measurements":[{"id":"patent","value":0.007,"unit":"in","pm":0.003,"source":{"type":"photo","photo":"references/magpul-mbus-3-front c0c71839efcb (US D1,010,056 S (Magpul, 'Gun sight'), FIG. 2 left elevation; the patent office's copy, page 4, 300 dpi)","scaleRef":"the patent's own folded length as .length (2.13 in): in FIG. 2 and FIG. 3 the base's front end to the hinge's axis, 792.0 px, plus the hinge's axis to the wings' top, 1165.4 px (the arm a quarter turn back about its hinge), 1957.4 px: 919.0 px/in; FIG. 4, FIG. 5 and FIG. 7 are drawn at the same scale (their rows and lengths agree to a pixel)","method":"the centre of the boss's circles (row 2144.8; the screw head's in FIG. 3, 2144.5) under the hinge block's underside (row 2138.5): 6.2 px","via":"harvest"}}]},"boss_d":{"label":"Left boss: its diameter","kind":"length","measurements":[{"id":"patent","value":0.425,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/magpul-mbus-3-front c0c71839efcb (US D1,010,056 S (Magpul, 'Gun sight'), FIG. 2 left elevation; the patent office's copy, page 4, 300 dpi)","scaleRef":"the patent's own folded length as .length (2.13 in): in FIG. 2 and FIG. 3 the base's front end to the hinge's axis, 792.0 px, plus the hinge's axis to the wings' top, 1165.4 px (the arm a quarter turn back about its hinge), 1957.4 px: 919.0 px/in; FIG. 4, FIG. 5 and FIG. 7 are drawn at the same scale (their rows and lengths agree to a pixel)","method":"the outermost of the boss's three circles: r 195.4 px (inner steps at r 173 and 157)","via":"harvest"}}],"note":"The round boss moulded on the left cheek, which the cross bolt threads into."},"boss_out":{"label":"Left boss: how far it stands off the cheek","kind":"length","measurements":[{"id":"patent","value":0.078,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/magpul-mbus-3-front 21c2b9876c1b (US D1,010,056 S (Magpul, 'Gun sight'), FIG. 4 rear elevation; the patent office's copy, page 6, 300 dpi)","scaleRef":"the patent's own folded length as .length (2.13 in): in FIG. 2 and FIG. 3 the base's front end to the hinge's axis, 792.0 px, plus the hinge's axis to the wings' top, 1165.4 px (the arm a quarter turn back about its hinge), 1957.4 px: 919.0 px/in; FIG. 4, FIG. 5 and FIG. 7 are drawn at the same scale (their rows and lengths agree to a pixel)","method":"the cheek's outer face (u 732.5) to the boss's face (u 660.5): 72 px; FIG. 7, 72 px. The underside photo (0933bc534c51) has it 50 px where the length is 1326: 0.080","via":"harvest"}}]},"screw_head_d":{"label":"Cross bolt's head: its diameter","kind":"length","measurements":[{"id":"patent","value":0.349,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-mbus-3-front 2017081c8b13 (US D1,010,056 S (Magpul, 'Gun sight'), FIG. 3 right elevation; the patent office's copy, page 5, 300 dpi)","scaleRef":"the patent's own folded length as .length (2.13 in): in FIG. 2 and FIG. 3 the base's front end to the hinge's axis, 792.0 px, plus the hinge's axis to the wings' top, 1165.4 px (the arm a quarter turn back about its hinge), 1957.4 px: 919.0 px/in; FIG. 4, FIG. 5 and FIG. 7 are drawn at the same scale (their rows and lengths agree to a pixel)","method":"the circle in broken lines at the bolt's axis: r 160.4 px (a second at r 173, a recess round it at r 204)","via":"harvest"}}],"note":"In broken lines in the patent (its environment, not the claimed design)."},"screw_head_out":{"label":"Cross bolt's head: how far it stands off the right cheek","kind":"length","measurements":[{"id":"photo","value":0.053,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-mbus-3-front 0933bc534c51 (Magpul's gallery image 03.1, \"Underside view of MBUS 3 Front Sight in stowed position\", in Impact Guns' 1500 px copy; Magpul's own 1200 px file is 2c3af1e179ed)","scaleRef":"the folded sight's own length in the same image, the wings' tips to the base's front end, 1326 px, as .length (2.13 in): 622.5 px/in. Seen from below, so the base is some 0.5 in nearer the lens than the arm's tip: sizes on the base read up to 2% large against that length","method":"the right cheek's outer face (u 1143) to the head's face (u 1176): 33 px; the front view (ff4952671f93) has it 36.5 px where the cheeks are 843 px apart: 0.050","via":"harvest"}},{"id":"patent","value":0.079,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/magpul-mbus-3-front 21c2b9876c1b (US D1,010,056 S (Magpul, 'Gun sight'), FIG. 4 rear elevation; the patent office's copy, page 6, 300 dpi)","scaleRef":"the patent's own folded length as .length (2.13 in): in FIG. 2 and FIG. 3 the base's front end to the hinge's axis, 792.0 px, plus the hinge's axis to the wings' top, 1165.4 px (the arm a quarter turn back about its hinge), 1957.4 px: 919.0 px/in; FIG. 4, FIG. 5 and FIG. 7 are drawn at the same scale (their rows and lengths agree to a pixel)","method":"the right cheek's outer face (u 1782.25) to the head's face in broken lines (u 1854.5): 72.25 px","via":"harvest"}}],"adopt":{"from":"photo","reason":"The screw as it is in the maker's two photographs; the patent draws it in broken lines, as its environment, and as far out as the boss."}},"wheel_d":{"label":"Elevation wheel's diameter","kind":"length","measurements":[{"id":"patent","value":0.407,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-mbus-3-front 21c2b9876c1b (US D1,010,056 S (Magpul, 'Gun sight'), FIG. 4 rear elevation; the patent office's copy, page 6, 300 dpi)","scaleRef":"the patent's own folded length as .length (2.13 in): in FIG. 2 and FIG. 3 the base's front end to the hinge's axis, 792.0 px, plus the hinge's axis to the wings' top, 1165.4 px (the arm a quarter turn back about its hinge), 1957.4 px: 919.0 px/in; FIG. 4, FIG. 5 and FIG. 7 are drawn at the same scale (their rows and lengths agree to a pixel)","method":"its flutes' spacing seen face on: the middle rib (u 1222 to 1293) and the next (u 1133.5 to 1194.5) are 93.5 px apart, and in FIG. 5 the one after stands 168 px off the middle: twelve flutes at 30° on a radius of 187 px","via":"harvest"}}],"note":"The fluted wheel the post screws through, in its window in the arm. It is as thick as the arm less 0.014 in and shows through both faces without standing out of either (the side elevations' edges are straight there)."},"wheel_flutes":{"label":"Elevation wheel's flutes","kind":"count","measurements":[{"id":"patent","value":12,"unit":"count","source":{"type":"photo","photo":"references/magpul-mbus-3-front 21c2b9876c1b (US D1,010,056 S (Magpul, 'Gun sight'), FIG. 4 rear elevation; the patent office's copy, page 6, 300 dpi)","scaleRef":"none needed: a ratio of two spacings in one figure","method":"the second rib's offset over the first's, 168 / 93.5 px = 1.80, is 2 cos of the angle between flutes: 26° to 30°, twelve to fourteen flutes; twelve fits the arm's thickness (wheel_d). Three ribs show in the rear window and five in the front","via":"harvest"}}]},"post_width_standard":{"label":"Sight post's width, standard","kind":"length","measurements":[{"id":"magpul","value":0.06,"unit":"in","stated":"Includes two adjustable sight post widths in one: a 0.06” Standard width for maximum visibility and a 0.04” Match width for increased precision","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MBUS 3 Sight – Front (MAG1166)","url":"https://magpul.com/mbus-3-sight-front.html","retrieved":"2026-10-05","via":"harvest"}}],"note":"The post has two widths a quarter turn apart; the installation sheet: \"The default position is the combat-width post.\""},"post_width_match":{"label":"Sight post's width, match","kind":"length","measurements":[{"id":"magpul","value":0.04,"unit":"in","stated":"Includes two adjustable sight post widths in one: a 0.06” Standard width for maximum visibility and a 0.04” Match width for increased precision","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MBUS 3 Sight – Front (MAG1166)","url":"https://magpul.com/mbus-3-sight-front.html","retrieved":"2026-10-05","via":"harvest"}}],"note":"The patent's elevations draw the post 0.037 in wide (34 px between its edges' strokes): the match width faces the eye there."}}},{"subject":"magpul-mbus-3-rear","title":"Magpul MBUS 3 Sight – Rear (MAG1167)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"magpul","value":30,"unit":"g","pm":0.5,"stated":"Weight, w/ hardware 30 g","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MBUS 3 Sight – Rear (MAG1167), Technical Specifications","url":"https://magpul.com/mbus-3-sight-rear.html","retrieved":"2026-10-05","via":"harvest"}},{"id":"trex","value":1,"unit":"oz","pm":0.05,"stated":"Weight 1.0 ounce (rear only) 1.9 ounces (front and rear)","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, Magpul MBUS 3 Sight - Rear, Technical Specifications (source of the figures unstated)","url":"https://www.trex-arms.com/store/magpul-mbus-3-sight-rear-865862","retrieved":"2026-10-05","via":"harvest"}}],"adopt":{"from":"magpul","reason":"The maker's own figure, with its hardware. The same page's feature list says \"lightweight (1.06 oz)\", which is 30 g; the seller's 1.0 ounce is the same weight to one decimal."}},"length":{"label":"Length along the rail (folded, where it folds)","kind":"length","measurements":[{"id":"patent","value":2.35,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-mbus-3-rear 615a86af0b47 (US D1,010,057 S (Magpul, 'Gun sight'), FIG. 2 left elevation, deployed; the patent office's copy, page 4, 300 dpi)","scaleRef":"the figures' one scale, set on FIG. 4 by Magpul's width at the widest point (.width, 1.38 in over 1235 px: 894.9 px/in); the aperture's height (.sight_line_above_rail) gives 899.3","method":"the arm turned flat about its hinge: the hinge's axis (the centre of the round lower end of the arm's side panel, a circle fitted to it: 1522.7, 2044.9) to the base's front end (731, the stroke's centre): 792 px; and to the arm's far end, the wings' rear top corner (731.5 up the sheet): 1313 px. 2105 px. ± covers the two published sizes' 0.5% and the strokes","via":"harvest"}},{"id":"photo-stowed","value":2.32,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-mbus-3-rear 9248df8685e9 (Impact Guns SSI133213_B: Magpul's photo of the olive sight stowed on a flat-top receiver, right side, the rail's teeth ahead of it; 1500 x 1500)","scaleRef":"the rail's two teeth in frame: their near corners 142 px apart and their far corners 136 (std.picatinny.slot_pitch): the lens about 20 in away, 360 px/in in the rail's near edge's plane and 362.6 in the plane of the sight's right side","method":"the arm's far end (u 361, rows 560 to 570) to the base's front end (u 1201, row 590), both on the side nearest the lens: 840 px; ± 4 px and the lens's distance","via":"harvest"}},{"id":"trex","value":2.43,"unit":"in","pm":0.005,"stated":"Length 2.43 inches","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, Magpul MBUS 3 Sight - Rear, Technical Specifications (source of the figures unstated)","url":"https://www.trex-arms.com/store/magpul-mbus-3-sight-rear-865862","retrieved":"2026-10-05","via":"harvest"}}],"adopt":{"from":"patent","reason":"Two readings that share nothing agree within their ±: the patent's elevation at the scale Magpul's own two sizes set, and Magpul's photo of it stowed on a rail by the rail's teeth. The seller's table doesn't say what its length is measured to or where it is from, and is 0.08 in more than both; Magpul states no length."},"note":"Stowed: the base's front end to the far end of the arm lying behind it. Standing it is 1.18 in along the rail (the patent's side elevation)."},"width":{"label":"Width","kind":"length","measurements":[{"id":"magpul","value":1.38,"unit":"in","pm":0.005,"stated":"0.55” high when folded and 1.38” wide at widest point","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MBUS 3 Sight – Rear (MAG1167), feature block","url":"https://magpul.com/mbus-3-sight-rear.html","retrieved":"2026-10-05","via":"harvest"}},{"id":"primary-arms","value":1.15,"unit":"in","pm":0.005,"stated":"this AR-15 iron sight folds down to just .44\" high and 1.15\" wide so it sits on slimmer rails without overhanging","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Magpul MBUS 3 Flip Up AR-15 Iron Sight - Rear - Olive Drab Green (MAG1167-ODG)","url":"https://www.primaryarms.com/magpul-mbus-3-rear-sight-olive-drab-green","retrieved":"2026-10-05","via":"harvest"}}],"adopt":{"from":"magpul","reason":"The maker's current page, and the patent's rear elevation bears it out: scaled by the aperture's height alone it is 1.373 in from the clamp's boss to the knob's end. The older figure is still on eight sellers' pages; on the patent's figures 1.15 to 1.17 in is the base across its side walls, without the knob and the clamp's boss."},"note":"At the widest point: the clamp's boss on the left to the windage knob's end on the right. The wings are 0.97 in across, the base 1.17."},"height":{"label":"Height above the rail's top, folded (a fixed sight: its height)","kind":"length","measurements":[{"id":"magpul","value":0.55,"unit":"in","pm":0.005,"stated":"Height above rail, stowed ~0.55 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MBUS 3 Sight – Rear (MAG1167), Technical Specifications","url":"https://magpul.com/mbus-3-sight-rear.html","retrieved":"2026-10-05","via":"harvest"}},{"id":"primary-arms","value":0.44,"unit":"in","pm":0.005,"stated":"this AR-15 iron sight folds down to just .44\" high and 1.15\" wide so it sits on slimmer rails without overhanging","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Magpul MBUS 3 Flip Up AR-15 Iron Sight - Rear - Olive Drab Green (MAG1167-ODG)","url":"https://www.primaryarms.com/magpul-mbus-3-rear-sight-olive-drab-green","retrieved":"2026-10-05","via":"harvest"}},{"id":"patent","value":0.52,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-mbus-3-rear 615a86af0b47 (US D1,010,057 S (Magpul, 'Gun sight'), FIG. 2 left elevation, deployed; the patent office's copy, page 4, 300 dpi)","scaleRef":"the figures' one scale (.width over FIG. 4's 1235 px: 894.9 px/in)","method":"the arm turned flat about its hinge: the hinge's axis stands 204.6 px above the rail's top (FIG. 4's channel ceiling, 56 rows down on this sheet: 2249.5) and the windage knob's collar is 520 px across on that axis: its rim 464.6 px above the rail. The arm's own top is then 0.44 in above the rail and the base's 0.44","via":"harvest"}}],"adopt":{"from":"magpul","reason":"The maker's own figure, measured from the rail's top (\"Height above rail, stowed\"), and stated as approximate. The patent's figures, with the arm laid flat, put the knob's rim at 0.52 in and the body at 0.44, and Magpul's photo of it stowed on a rail reads the same two (0.51 and 0.45): the older 0.44 that eight sellers still print fits the body without the knob."},"note":"From the rail's top to its highest point stowed, the windage knob's rim. T.REX ARMS adds \"0.63 inches (total)\", which on the patent's figures would be 0.77 (the clamp reaches 0.25 in below the rail's top)."},"height_up":{"label":"Height above the rail's top, standing","kind":"length","measurements":[{"id":"patent","value":1.696,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{.overall_height_up} - {.clamp_below_rail}","via":"harvest"}}],"note":"To the wings' tops. Not published: the patent's rear elevation, the clamp's lower edge to the wings' tops, less the clamp's reach below the rail's top."},"sight_line_above_rail":{"label":"Sight line above the rail's top (the aperture's centre, the post's tip)","kind":"length","measurements":[{"id":"magpul","value":1.42,"unit":"in","pm":0.005,"stated":"Center of aperture to top of rail: 1.42 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MBUS 3 Sight – Rear (MAG1167), Technical Specifications, Other Specs","url":"https://magpul.com/mbus-3-sight-rear.html","retrieved":"2026-10-05","via":"harvest"}},{"id":"trex","value":1.41,"unit":"in","pm":0.005,"stated":"Centerline Height 1.41 inches","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, Magpul MBUS 3 Sight - Rear, Technical Specifications (source of the figures unstated)","url":"https://www.trex-arms.com/store/magpul-mbus-3-sight-rear-865862","retrieved":"2026-10-05","via":"harvest"}},{"id":"patent","value":1.427,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-mbus-3-rear 1e9f20f4f5f7 (US D1,010,057 S (Magpul, 'Gun sight'), FIG. 4 rear elevation, deployed; the patent office's copy, page 6, 300 dpi)","scaleRef":".width, 1.38 in, over the figure's 1235 px between the stroke centres of the clamp's boss and the knob's end: 894.9 px/in","method":"the channel's ceiling (the broken line at row 2193.5, columns 1000 to 1560) to the small aperture's centre (the centroid of the circle its strokes close: 1237.5, 916.5): 1277 px","via":"harvest"}}],"adopt":{"from":"magpul","reason":"The maker's own figure, and it says what it is measured to. The seller's is 0.01 in less; the patent's figure, scaled by the width, is 0.007 in more."},"note":"The small aperture standing. The aperture arm turns over about the windage screw to bring the large aperture up (\"flip the aperture arm 180-degrees\", the instruction sheet); on the patent's figure the two are 302 and 307 px either side of the screw's axis, so the large one stands within 0.006 in of the same height."},"clamp_length":{"label":"Clamp's length along the rail","kind":"length","measurements":[{"id":"patent","value":0.686,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-mbus-3-rear 615a86af0b47 (US D1,010,057 S (Magpul, 'Gun sight'), FIG. 2 left elevation, deployed; the patent office's copy, page 4, 300 dpi)","scaleRef":"scale from magpul-mbus-3-rear.overall_height_up = 1.949 in (y-extent 1744 px → 894.8 px/in)","method":"−x_min in y [0.02, 0.15] of the traced outline (tools/trace.py); the base's front end to its rear end over the rows where its jaws are on the rail's sides (0.1 to 0.23 in below the rail's top)","via":"harvest"}}],"note":"The base's two ends where it is on the rail. Not published; from the patent's side elevation."},"overall_height_up":{"label":"Overall height standing (the clamp's lower edge to the wings' tops)","kind":"length","measurements":[{"id":"patent","value":1.949,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-mbus-3-rear 1e9f20f4f5f7 (US D1,010,057 S (Magpul, 'Gun sight'), FIG. 4 rear elevation, deployed; the patent office's copy, page 6, 300 dpi)","scaleRef":"scale from magpul-mbus-3-rear.width = 1.38 in (x-extent 1235 px → 894.9 px/in)","method":"height of the traced outline (tools/trace.py); the rear elevation's overall height, the clamp's lower edge to the wings' tops, at the scale Magpul's width sets","via":"harvest"}}],"note":"What the patent's elevations are tall: FIG. 2 to FIG. 5 all 1748 px, which is how the side elevation takes the rear elevation's scale."},"clamp_below_rail":{"label":"Clamp's lower edge below the rail's top","kind":"length","measurements":[{"id":"patent","value":0.253,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-mbus-3-rear 1e9f20f4f5f7 (US D1,010,057 S (Magpul, 'Gun sight'), FIG. 4 rear elevation, deployed; the patent office's copy, page 6, 300 dpi)","scaleRef":".width, 1.38 in, over the figure's 1235 px: 894.9 px/in","method":"the channel's ceiling (the broken line at row 2193.5) to the jaws' lower edge (the stroke at rows 2418 to 2421): 226 px","via":"harvest"}}],"note":"The rail's top is the ceiling of the channel the patent draws in broken lines: 0.89 in wide over the rail's 0.835 (std.picatinny.top_width), hooked under its 45° faces to 0.70 in. In Magpul's photo of it on a receiver the base reaches about as far down the rail's side."},"clamp_bottom_y":{"label":"Clamp's lower edge in the sight's frame (y, the rail's top is 0)","kind":"length","measurements":[{"id":"derived","value":-0.253,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"-{.clamp_below_rail}","via":"harvest"},"note":"Where the traced outlines' lower edge sits in the part frame: the profiles' y offset."}]},"clamp_front_x":{"label":"Base's front end ahead of the clamp's middle (the sight frame's x origin)","kind":"length","measurements":[{"id":"derived","value":0.343,"unit":"in","pm":0.008,"source":{"type":"derived","expr":"{.clamp_length} / 2","via":"harvest"},"note":"The traced outlines' x origin is the base's front end: the profiles' x offset to the clamp's middle."}]},"bolt_from_front":{"label":"Cross bolt's axis behind the base's front end","kind":"length","measurements":[{"id":"patent","value":0.292,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-mbus-3-rear 615a86af0b47 (US D1,010,057 S (Magpul, 'Gun sight'), FIG. 2 left elevation, deployed; the patent office's copy, page 4, 300 dpi)","scaleRef":"the figures' one scale (.width over FIG. 4's 1235 px: 894.9 px/in)","method":"the base's front end (731) to the centre of the clamp boss's face (a circle fitted to its stroke: 992.6, 2253.9, 308 px across): 261.6 px. The boss's axis is 4 px under the rail's top line","via":"harvest"}}],"note":"The 10-24 screw that draws the clamp shut crosses the channel at the rail's top and sits in one of the rail's slots (Magpul's underside photo: \"Picatinny clamp and shouldered mounting screw\"): it is what a slot holds, so the mount's anchor is on its axis. The right elevation's hex socket (FIG. 3, broken lines) is on the same axis."},"clamp_screw_hex":{"label":"Clamp screw's hex socket (across its flats)","kind":"length","measurements":[{"id":"magpul","value":0.125,"unit":"in","pm":0.001,"stated":"Using a flat head screwdriver or 1/8” hex key, hand tighten the 10-24 Dual-Drive Screw.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MBUS Sight - Rear installation instructions (092-0065-A), Step 2: Mount sight","url":"https://magpul.com/media/wysiwyg/Instructions/MAG1167_MBUS_Rear_Sight_INSRT.pdf","retrieved":"2026-10-05","via":"harvest"}}],"note":"The key's size is the socket's across its flats. The patent's right elevation (FIG. 3) draws the socket in broken lines on the cross screw's axis, about 130 px across its corners: 0.145 in at the figures' scale, 0.126 across the flats."},"aperture_behind_front":{"label":"Aperture arm's bar behind the base's front end (its mid-thickness)","kind":"length","measurements":[{"id":"patent","value":1.061,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-mbus-3-rear baf4699b50f5 (US D1,010,057 S (Magpul, 'Gun sight'), FIG. 6 top plan, deployed; the patent office's copy, page 8, 300 dpi)","scaleRef":"the figures' one scale (.width over the plan's own 1237 px across: 896.4 px/in)","method":"the base's front end (733) to the bar between the wings, seen from above as a strip 1651 to 1717 (the arm's rear face): its middle, 951 px","via":"harvest"}}],"note":"Where the aperture is along the rail: the bar lies against the arm's rear face, 0.075 in thick."},"aperture_small_d":{"label":"Small aperture's diameter","kind":"length","measurements":[{"id":"trex","value":0.063,"unit":"in","pm":0.0005,"stated":"Aperture Size 0.063 inches (small aperture) 0.19 inches (large aperture)","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, Magpul MBUS 3 Sight - Rear, Technical Specifications (source of the figures unstated)","url":"https://www.trex-arms.com/store/magpul-mbus-3-sight-rear-865862","retrieved":"2026-10-05","via":"harvest"}}],"note":"Magpul states no aperture size. The patent's small circle is 0.071 in across its stroke centres."},"aperture_large_d":{"label":"Large aperture's diameter","kind":"length","measurements":[{"id":"trex","value":0.19,"unit":"in","pm":0.005,"stated":"Aperture Size 0.063 inches (small aperture) 0.19 inches (large aperture)","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, Magpul MBUS 3 Sight - Rear, Technical Specifications (source of the figures unstated)","url":"https://www.trex-arms.com/store/magpul-mbus-3-sight-rear-865862","retrieved":"2026-10-05","via":"harvest"}}],"note":"The patent's large circle is 0.194 in across its stroke centres: the seller's figure and the drawing agree."}}},{"subject":"magpul-mbus-pro-front","title":"Magpul MBUS Pro Sight – Front (MAG275)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"magpul","value":1.5,"unit":"oz","pm":0.05,"stated":"Weight 1.5 oz.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MBUS Pro Sight – Front, Model MAG275, Technical Specifications","url":"https://magpul.com/firearm-accessories/sights/mbus-pro/mbus-pro-sight-front.html","retrieved":"2026-10-05","via":"harvest"}},{"id":"wing","value":1.51,"unit":"oz","pm":0.005,"stated":"Weight: 1.51 oz.","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Magpul MBUS Pro Front Sight (MPN MAG275), Specifications (source of the figure unstated)","url":"https://www.wingtactical.com/accessories/ar-15-sights-and-optics/ar-15-sights/magpul-mbus-pro-front-sight/","retrieved":"2026-10-05","via":"harvest"}}],"adopt":{"from":"magpul","reason":"The maker's figure; a retailer's own agrees."},"note":"With its cross bolt (sellers carrying Magpul's earlier text write \"Weight, w/ hardware: 1.5 oz.\"). Recoil's 2015 guide gives the pair at 3.35 oz / 95 g."},"length":{"label":"Length along the rail (folded, where it folds)","kind":"length","measurements":[{"id":"magpul","value":1.63,"unit":"in","pm":0.005,"stated":"Length, stowed 1.63 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MBUS Pro Sight – Front, Model MAG275, Technical Specifications","url":"https://magpul.com/firearm-accessories/sights/mbus-pro/mbus-pro-sight-front.html","retrieved":"2026-10-05","via":"harvest"},"note":"And among its features: \"Stowed footprint covers 1.63” of rail\"."},{"id":"wing","value":1.6,"unit":"in","pm":0.05,"stated":"Length, stowed: 1.6\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Magpul MBUS Pro Front Sight (MPN MAG275), Specifications","url":"https://www.wingtactical.com/accessories/ar-15-sights-and-optics/ar-15-sights/magpul-mbus-pro-front-sight/","retrieved":"2026-10-05","via":"harvest"},"note":"Magpul's earlier wording, which Primary Arms, Midwest Gun Works, Scheels, Mile High, KYGUNCO, Dirty Bird and AR15Discounts carry too: a figure to one decimal, which both 1.57 and 1.63 round to."},{"id":"recoil","value":1.57,"unit":"in","pm":0.005,"stated":"Front Length: 1.57 in / 40 mm (stowed)","source":{"type":"spec","publisher":"review","name":"Recoil, Back-up Iron Sights Buyer's Guide (2015-12-28), the MBUS Pro's table (who measured, and how, unstated)","url":"https://www.recoilweb.com/back-up-iron-sights-78135.html","retrieved":"2026-10-05","via":"harvest"}},{"id":"rail","value":1.564,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-mbus-pro-front 3dc752d09e8f (US D705,890 S (Magpul, 'Folding front sight for a firearm'), FIG. 6 right side elevation; the patent office's copy, page 4, 300 dpi)","scaleRef":"the clamp in the rear elevation (FIG. 4, 5412c5a0484c, drawn at the side elevations' scale): the fixed jaw's vee (u 1702) to the clamp bar's wall (u 877), 825 px, as a rail of std.picatinny.top_width (.835 in): 988 px/in","method":"the side elevation's length, 1545 px between its strokes' centres (u 488 to 2033); ± 4 px on the jaws and the standard's -.005","via":"harvest"},"note":"Holds only if the patent draws the clamp closed on a rail. Its cross bolt, 190 px across in the same figure, says the same of a No. 10 screw (0.190 in: 1000 px/in)."}],"adopt":{"from":"magpul","reason":"The maker's own current figure, stated twice, and the one its two heights go with: 1.56 deployed less ~0.43 stowed is 1.13 in, and the patent's figures at this length's scale give 1.123. Recoil's 1.57 and a rail in the patent's clamp both say 4% less; nothing on file shows the sight beside a scale to settle it."},"note":"The base's front end to the wings' tips, the arm folded to the rear. The patent's figures are the model's shape and this figure their scale (the subject's header has what was tried against it)."},"width":{"label":"Width","kind":"length","measurements":[{"id":"patent","value":1.248,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-mbus-pro-front 5412c5a0484c (US D705,890 S (Magpul, 'Folding front sight for a firearm'), FIG. 3 front elevation; the patent office's copy, page 3, 300 dpi)","scaleRef":"the figure's overall height, 632 px, is the side elevation's (631 px, FIG. 6): one scale, the side elevation's length as .length (1545 px = 1.63 in, 947.9 px/in)","method":"the nut's outer face (u 673) to the cross bolt's head (u 1856): 1183 px; FIG. 4 reads 1184. ± covers the length's ±, the reading and a design patent's fidelity","via":"harvest"}}],"note":"No page states it. Across the cross bolt, its head on the rifle's left and its nut on the right; the body alone (the base's two legs) is 1019 px, 1.075 in. Dirty Bird's and AR15Discounts' shop fields print \"1.63 × 0.43 × 1.44 in\" unlabelled (their markup calls 1.44 the height and 0.43 the width): 1.44 is no size of this sight the figures give."},"height":{"label":"Height above the rail's top, folded (a fixed sight: its height)","kind":"length","measurements":[{"id":"magpul","value":0.43,"unit":"in","stated":"Height above rail, stowed ~0.43 in. max","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MBUS Pro Sight – Front, Model MAG275, Technical Specifications","url":"https://magpul.com/firearm-accessories/sights/mbus-pro/mbus-pro-sight-front.html","retrieved":"2026-10-05","via":"harvest"}},{"id":"recoil","value":0.43,"unit":"in","stated":"Front Height: 0.43 in / 11 mm (stowed)","source":{"type":"spec","publisher":"review","name":"Recoil, Back-up Iron Sights Buyer's Guide (2015-12-28), the MBUS Pro's table (who measured, and how, unstated)","url":"https://www.recoilweb.com/back-up-iron-sights-78135.html","retrieved":"2026-10-05","via":"harvest"}},{"id":"patent","value":0.455,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-mbus-pro-front 5412c5a0484c (US D705,890 S (Magpul, 'Folding front sight for a firearm'), FIG. 3 front elevation; the patent office's copy, page 3, 300 dpi)","scaleRef":"the figure's overall height, 632 px, is the side elevation's (631 px, FIG. 6): one scale, the side elevation's length as .length (1545 px = 1.63 in, 947.9 px/in)","method":"the roof of the clamp's channel (the heavy line at row 1218) to the top of the elevation knob and the ridges beside it (row 787): 431 px","via":"harvest"},"note":"From the channel's roof, taken as the rail's top (the base resting on the rail). At 988 px/in, the scale a rail in the clamp sets, it is 0.436."}],"adopt":{"from":"magpul","reason":"The maker's figure, which it marks approximate (\"~\", \"max\"). The patent's figures at the length's scale stand 0.025 in more above the channel's roof: the model is that much taller folded than this figure."},"note":"Above the rail's top, as Magpul words it: the clamp reaches .clamp_depth below it."},"height_up":{"label":"Height above the rail's top, standing","kind":"length","measurements":[{"id":"magpul","value":1.56,"unit":"in","pm":0.005,"stated":"STOWED HEIGHT OF ONLY 0.43\" KEEPS YOUR BACKUP OUT OF SIGHT; STANDARD AR SIGHT HEIGHT (1.56” ABOVE RAIL) WHEN DEPLOYED","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MBUS Pro Sight – Front, Model MAG275, a feature heading","url":"https://magpul.com/firearm-accessories/sights/mbus-pro/mbus-pro-sight-front.html","retrieved":"2026-10-05","via":"harvest"},"note":"Read as the top of the two wings, not the post's tip (.sight_line_above_rail has why)."},{"id":"patent","value":1.578,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-mbus-pro-front 3dc752d09e8f (US D705,890 S (Magpul, 'Folding front sight for a firearm'), FIG. 6 right side elevation; the patent office's copy, page 4, 300 dpi)","scaleRef":"the figure's own length, 1545 px, as .length (1.63 in): 947.9 px/in","method":"the hinge pin's centre above the channel's roof (.pivot_y, 243 px) plus the arm's reach from it to the wings' tips (.arm_reach, 1253 px): the arm turned a quarter turn about the pin. ± covers the length's ±, the readings and a design patent's fidelity","via":"harvest"}}],"adopt":{"from":"magpul","reason":"The maker's figure; the patent's arm, stood up about its hinge at the length's scale, reaches 0.018 in more."},"note":"To the wings' tips, the highest of it standing. The post's tip is lower (.sight_line_above_rail)."},"sight_line_above_rail":{"label":"Sight line above the rail's top (the aperture's centre, the post's tip)","kind":"length","measurements":[{"id":"magpul","value":1.56,"unit":"in","pm":0.005,"stated":"STOWED HEIGHT OF ONLY 0.43\" KEEPS YOUR BACKUP OUT OF SIGHT; STANDARD AR SIGHT HEIGHT (1.56” ABOVE RAIL) WHEN DEPLOYED","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MBUS Pro Sight – Front, Model MAG275, a feature heading","url":"https://magpul.com/firearm-accessories/sights/mbus-pro/mbus-pro-sight-front.html","retrieved":"2026-10-05","via":"harvest"},"note":"The page ties this figure to the sight height. It lands on the wings' tips (.height_up), 0.15 in above the post's."},{"id":"rear","value":1.41,"unit":"in","pm":0.005,"stated":"STOWED HEIGHT OF ONLY 0.38\" KEEPS YOUR BACKUP OUT OF SIGHT; STANDARD AR SIGHT HEIGHT (1.41” ABOVE RAIL) WHEN DEPLOYED","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MBUS Pro Sight – Rear, Model MAG276 (the rear sight of the pair), a feature heading; its table: \"Aperture height over rail: 1.42 in.\"","url":"https://magpul.com/mbus-pro-sight-rear.html","retrieved":"2026-10-05","via":"harvest"},"note":"The same sentence on the rear sight's page, where the figure is its aperture's. The front's sheet (072-0074-A) puts the two on one plane, so a line of sight level with the rail has the post's tip at the aperture's height."},{"id":"photo","value":1.414,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-mbus-pro-front 0c680e234c1c (Magpul's gallery, mag275-blk_mbus_pro_sight_front_02_1.jpg: the sight standing, straight from the shooter's end, 1200 x 1200)","scaleRef":"the arm's reach in the gallery's side view at the same magnification (02c61aa64f62: the hinge pin's centre, row 782, to the wings' tips, row 228: 554 px) as .arm_reach: 419 px/in","method":"the post's tip (row 270) 61 px below the wings' tips (rows 208 to 210): 0.146 in, taken off Magpul's 1.56 for the wings' tips (.height_up). ± 4 px on the two photos' scale and the tips","via":"harvest"},"note":"The post screws up and down (about 0.004 in a click by Magpul's click value): this is where Magpul's own photo has it."},{"id":"patent","value":1.459,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-mbus-pro-front e8f213fddc31 (US D705,890 S (Magpul, 'Folding front sight for a firearm'), FIG. 7 top plan; the patent office's copy, page 5, 300 dpi)","scaleRef":"the plan's own length, 1465 px, as .length (1.63 in): 898.6 px/in along the sight","method":"the post's tip (u 578) 91 px short of the wings' tips (u 487): 0.101 in, taken off Magpul's 1.56 for the wings' tips (.height_up)","via":"harvest"},"note":"Where the patent draws an adjustable post: 0.045 in higher than Magpul's photo has it."}],"adopt":{"from":"rear","reason":"Magpul's 1.56 is the sight's top: the patent's wings stand 1.58 at the length's scale, and in Magpul's own photo the post's tip is 0.146 in below them, which is 1.56 less the 1.41 to 1.42 its rear sight's page gives the same sentence and its aperture. The post's tip, at the height the pair is made to share."},"note":"The post's tip, standing, at the setting that puts it level with the rear sight's aperture on one rail: it is adjustable for elevation."},"clamp_length":{"label":"Clamp's length along the rail","kind":"length","measurements":[{"id":"patent","value":1.035,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-mbus-pro-front 3dc752d09e8f (US D705,890 S (Magpul, 'Folding front sight for a firearm'), FIG. 6 right side elevation; the patent office's copy, page 4, 300 dpi)","scaleRef":"the figure's own length, 1545 px, as .length (1.63 in): 947.9 px/in","method":"the base's two ends on its bottom line (u 1052 and 2033): 981 px; FIG. 5 reads the same (u 489 to 1470)","via":"harvest"}}],"note":"The whole base: the saddle under the hinge and the clamp behind it. The cross bolt, which is its recoil lug, is 0.20 in behind the middle (.screw_behind_front); the arm, folded, reaches 0.60 in behind the base."},"screw_behind_front":{"label":"Cross bolt's axis behind the base's front end","kind":"length","measurements":[{"id":"patent","value":0.717,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/magpul-mbus-pro-front 3dc752d09e8f (US D705,890 S (Magpul, 'Folding front sight for a firearm'), FIG. 6 right side elevation; the patent office's copy, page 4, 300 dpi)","scaleRef":"the figure's own length, 1545 px, as .length (1.63 in): 947.9 px/in","method":"the nut's rings, concentric about (1353, 2378) (the outer one 143 px in radius), behind the base's front end (u 2033): 680 px of the base's 981. ± covers the length's ±, 3 px on the rings' centre and a design patent's fidelity","via":"harvest"}},{"id":"photo","value":0.712,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-mbus-pro-front 02c61aa64f62 (Magpul's gallery, the sight standing, straight from the rifle's left: the cross bolt's head toward the camera, 1200 x 1200)","scaleRef":"the base's own length in the photo, 442 px (its silhouette's two ends, columns 390 and 832), as .clamp_length (1.035 in): 427 px/in","method":"the head's centre (column 694: the middle of the arc its rim makes below the clamp's bottom edge, the same at three heights) behind the base's front end (column 390): 304 px of 442. ± 3 px on the centre and on each end, and the head standing 0.1 in nearer the lens than the wall","via":"harvest"},"note":"A fraction of the base's length (0.688; the patent's is 0.693): the scale is the patent's, the place is the photo's own. The part's notes had the photo's head \"about 0.07 in further back\" than the patent's until 2026-10-05: measured, it is 0.005 in further forward."}],"adopt":{"from":"patent","reason":"The figure the model is built from, so the bolt drawn is the bolt the slot holds; Magpul's photo of the sight as sold agrees within its own reading."},"note":"The cross bolt is the sight's recoil lug (Magpul's sheet: \"Push Sight forward in recess until recoil lug is engaged\"): it crosses the clamp's channel with its lower part below the rail's top (.clamp_depth has the channel; the front elevation draws the bolt's underside 0.114 in below the roof), so it is what a rail's slot holds, and the sight is placed on a rail by it. The base reaches this far ahead of the slot's centre and .clamp_length less this (0.32 in) behind it. Until 2026-10-05 the sight was placed by the middle of its base, which put the bolt over a tooth, half a pitch from any slot."},"clamp_depth":{"label":"Clamp's reach below the rail's top","kind":"length","measurements":[{"id":"patent","value":0.212,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/magpul-mbus-pro-front 5412c5a0484c (US D705,890 S (Magpul, 'Folding front sight for a firearm'), FIG. 3 front elevation; the patent office's copy, page 3, 300 dpi)","scaleRef":"the figure's overall height, 632 px, is the side elevation's (631 px, FIG. 6): one scale, the side elevation's length as .length (1545 px = 1.63 in, 947.9 px/in)","method":"the roof of the clamp's channel (the heavy line at row 1218) to the jaws' lowest point (row 1419): 201 px; FIG. 4 reads the same (rows 2320 and 2521)","via":"harvest"}}],"note":"The channel's roof is taken as the rail's top: the frame's origin. Not a figure Magpul gives."},"folded_overall_height":{"label":"Overall height folded (the jaws' bottom to the knob's top)","kind":"length","measurements":[{"id":"patent","value":0.666,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/magpul-mbus-pro-front 3dc752d09e8f (US D705,890 S (Magpul, 'Folding front sight for a firearm'), FIG. 6 right side elevation; the patent office's copy, page 4, 300 dpi)","scaleRef":"the figure's own length, 1545 px, as .length (1.63 in): 947.9 px/in","method":"the base's bottom line (row 2566) to the top of the elevation knob and the ridges beside it (row 1935): 631 px; FIG. 5 reads 631 (rows 1493 and 862)","via":"harvest"}}],"note":"What the front elevation is scaled by: it shows the same height (632 px)."},"pivot_x":{"label":"Hinge pin's axis ahead of the clamp's middle","kind":"length","measurements":[{"id":"patent","value":0.209,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/magpul-mbus-pro-front 3dc752d09e8f (US D705,890 S (Magpul, 'Folding front sight for a firearm'), FIG. 6 right side elevation; the patent office's copy, page 4, 300 dpi)","scaleRef":"the figure's own length, 1545 px, as .length (1.63 in): 947.9 px/in","method":"the pin's pocket, a circle of 79.5 px about (1741, 2122) (the fraction of each candidate circle lying on the drawing's strokes, searched over centre and radius): 292 px behind the base's front end (u 2033), which is half of .clamp_length ahead of the middle. FIG. 5's pin is 291 px behind its front end","via":"harvest"}}]},"pivot_y":{"label":"Hinge pin's axis above the rail's top","kind":"length","measurements":[{"id":"patent","value":0.256,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/magpul-mbus-pro-front 3dc752d09e8f (US D705,890 S (Magpul, 'Folding front sight for a firearm'), FIG. 6 right side elevation; the patent office's copy, page 4, 300 dpi)","scaleRef":"the figure's own length, 1545 px, as .length (1.63 in): 947.9 px/in","method":"the pin's pocket, a circle about (1741, 2122): 444 px above the base's bottom line (row 2566), less the 201 px of .clamp_depth: 243 px. FIG. 5's pin is 444 px above its bottom line too","via":"harvest"}}]},"arm_reach":{"label":"Arm's reach from the hinge pin's axis to the wings' tips","kind":"length","measurements":[{"id":"patent","value":1.322,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-mbus-pro-front 3dc752d09e8f (US D705,890 S (Magpul, 'Folding front sight for a firearm'), FIG. 6 right side elevation; the patent office's copy, page 4, 300 dpi)","scaleRef":"the figure's own length, 1545 px, as .length (1.63 in): 947.9 px/in","method":"the pin's centre (u 1741) to the wings' tips (u 488), along the folded arm: 1253 px. FIG. 5 reads 1253 (u 780 to 2033)","via":"harvest"}}],"note":"Folded, it lies along the rail; standing, it is the height of the wings' tips above the pin. Magpul's gallery side view of it standing (02c61aa64f62) has the arm's reach 1.253 of the base's length; the patent, 1.277."},"knob_diameter":{"label":"Elevation knob's diameter","kind":"length","measurements":[{"id":"patent","value":0.388,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-mbus-pro-front 3dc752d09e8f (US D705,890 S (Magpul, 'Folding front sight for a firearm'), FIG. 6 right side elevation; the patent office's copy, page 4, 300 dpi)","scaleRef":"the figure's own length, 1545 px, as .length (1.63 in): 947.9 px/in","method":"twice the knob's top (row 1938) above the hinge pin's axis (row 2122), on which the post's axis and so the knob's lies: 2 x 184 px. The top plan (FIG. 7) draws the knob 358 px across at its own scale across the sight (0.970 of this one): 369 px here","via":"harvest"}}],"note":"A fluted drum on the post's axis, in a window through the arm; it stands 0.07 in out of the arm's face."},"post_width_standard":{"label":"Post's width, its Standard face","kind":"length","measurements":[{"id":"magpul","value":0.06,"unit":"in","pm":0.005,"stated":"Includes two adjustable sight post widths in one: a 0.06” Standard width for maximum visibility and a 0.04” Match width for increased precision","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MBUS Pro Sight – Front, Model MAG275, Features","url":"https://magpul.com/firearm-accessories/sights/mbus-pro/mbus-pro-sight-front.html","retrieved":"2026-10-05","via":"harvest"}}]},"post_width_match":{"label":"Post's width, its Match face","kind":"length","measurements":[{"id":"magpul","value":0.04,"unit":"in","pm":0.005,"stated":"Includes two adjustable sight post widths in one: a 0.06” Standard width for maximum visibility and a 0.04” Match width for increased precision","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MBUS Pro Sight – Front, Model MAG275, Features","url":"https://magpul.com/firearm-accessories/sights/mbus-pro/mbus-pro-sight-front.html","retrieved":"2026-10-05","via":"harvest"}}],"note":"The face it is assembled with toward the shooter: \"The sight is assembled with the thinner .040” Match side showing but .060” Standard width may be selected for greater visibility\" (Magpul's sheet 072-0074-A)."},"screw_hex":{"label":"Cross bolt's hex socket (across its flats)","kind":"length","measurements":[{"id":"magpul","value":0.125,"unit":"in","pm":0.001,"stated":"Using a 1/8” hex key or flat-head screwdriver, loosen the 10-24 dual-drive screw enough to mount sight onto the rail.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MAG275 MBUS Pro Sight – Front installation instructions (072-0074-A), POSITION SIGHT ON RAIL","url":"https://magpul.com/media/wysiwyg/Instructions/MAG275_MBUS_Pro_Front_INSRT.pdf","retrieved":"2026-10-05","via":"harvest"}}],"note":"The key's size, taken as the socket's. The bolt's thread is 10-24 by the same sentence; the patent draws it 0.20 in across at the length's scale (a No. 10 thread is 0.190)."}}},{"subject":"magpul-mbus-pro-rear","title":"Magpul MBUS Pro Sight – Rear (MAG276)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"magpul","value":1.8,"unit":"oz","pm":0.005,"stated":"Weight, w/ hardware 1.80 oz.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MBUS Pro Sight – Rear (MAG276), Technical Specifications","url":"https://magpul.com/mbus-pro-sight-rear.html","retrieved":"2026-10-05","via":"harvest"}},{"id":"ar15discounts","value":1.76,"unit":"oz","stated":"Additional information Weight 1.76 oz","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, Magpul MBUS Pro Rear Flip Sight - Black (MPIMAG276), Additional information (the shop's own field; its description beside it prints Magpul's \"Weight, w/ hardware: 1.80 oz.\")","url":"https://ar15discounts.com/products/magpul-mbus-pro-rear-flip-sight-black/","retrieved":"2026-10-05","via":"harvest"}}],"adopt":{"from":"magpul","reason":"The maker's figure, which the same seller's description repeats; its shop field's 1.76 oz states no method and may be a shipping entry."},"note":"With its clamp screw (\"w/ hardware\"). Recoil's 2015 table gives 3.35 oz / 95 g for the front and rear together, which says nothing of the rear alone."},"length":{"label":"Length along the rail (folded, where it folds)","kind":"length","measurements":[{"id":"magpul","value":2.1,"unit":"in","stated":"Length, stowed 2.1 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MBUS Pro Sight – Rear (MAG276), Technical Specifications; its Features say \"Stowed footprint covers 2.1” of rail\"","url":"https://magpul.com/mbus-pro-sight-rear.html","retrieved":"2026-10-05","via":"harvest"}},{"id":"recoil","value":2.08,"unit":"in","stated":"Rear Length: 2.08 in / 52.8 mm (stowed)","source":{"type":"spec","publisher":"review","name":"Recoil, Back-up Iron Sights Buyer's Guide (Rob Curtis, 2015-12-28), Magpul MBUS Pro table (who measured, and how, unstated)","url":"https://www.recoilweb.com/back-up-iron-sights-78135.html","retrieved":"2026-10-05","via":"harvest"}}],"adopt":{"from":"magpul","reason":"The maker's figure; the review's 2.08 in is inside its last digit."},"note":"Folded: from the base's front face to the folded arm's rear tip (\"Stowed footprint covers 2.1” of rail\"). Standing it is the base alone (clamp_length) and, behind it, what the arm and the windage knob overhang it by: 0.08 in."},"height":{"label":"Height above the rail's top, folded (a fixed sight: its height)","kind":"length","measurements":[{"id":"magpul","value":0.38,"unit":"in","stated":"Height above rail, stowed ~0.38 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MBUS Pro Sight – Rear (MAG276), Technical Specifications; its Features say \"Standard AR sight height when deployed and 0.38\" when stowed\"","url":"https://magpul.com/mbus-pro-sight-rear.html","retrieved":"2026-10-05","via":"harvest"}},{"id":"wing","value":0.37,"unit":"in","stated":"Height above rail, stowed, at mid-point: ~0.37\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Magpul Back Up Rear Sight (MBUS) Pro (MAG276), Specifications (Magpul's older text: AR15Discounts and Midwest Gun Works print the same line)","url":"https://www.wingtactical.com/accessories/ar-15-sights-and-optics/ar-15-sights/magpul-back-up-rear-sight-mbus-pro/","retrieved":"2026-10-05","via":"harvest"}},{"id":"recoil","value":0.36,"unit":"in","stated":"Rear Height: 0.36 in / 9.1 mm (stowed)","source":{"type":"spec","publisher":"review","name":"Recoil, Back-up Iron Sights Buyer's Guide (Rob Curtis, 2015-12-28), Magpul MBUS Pro table (who measured, and how, unstated)","url":"https://www.recoilweb.com/back-up-iron-sights-78135.html","retrieved":"2026-10-05","via":"harvest"}},{"id":"patent","value":0.37,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-mbus-pro-rear 5159aa124947 (US D704,792 S, Magpul, FIG. 3 front elevation, folded; the patent office's copy, page 5, 300 dpi)","scaleRef":"the figure's width as the plan's (.width, itself by the stowed length): 1288 px, 922.0 px/in","method":"the top of the rib that carries the windage pointer, on the sight's centre line (row 924), above the channel's roof (row 1265): 341 px. The folded arm's flat top is 0.341 in above the rail by the side elevation, the base's top 0.332","via":"harvest"}}],"adopt":{"from":"magpul","reason":"The maker's current figure. Its older ~0.37 in (\"at mid-point\") is within the last digit of it, and the patent's centre-line top, scaled by the stowed length, reads 0.370; the review's 0.36 isn't within its digit, and states no method."},"note":"From the rail's top (\"Height above rail\"), not the clamp's bottom. To what, Magpul's page doesn't say; its older wording, which sellers still print, is \"at mid-point\", and on the patent the sight's top on its centre line (the rib that carries the windage pointer) is 0.370 in above the rail. The folded arm's flat top is lower (0.34), and two things off the centre line are higher: the ear beside the windage knob (0.40) and the knob's own top (0.43, knob_top_above_rail)."},"width":{"label":"Width","kind":"length","measurements":[{"id":"patent","value":1.397,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-mbus-pro-rear f9854fd2c2a8 (US D704,792 S (Magpul, 'Folding rear sight for a firearm'), FIG. 7 top plan, folded; the patent office's copy, page 7, 300 dpi)","scaleRef":"scale from magpul-mbus-pro-rear.length = 2.1 in (x-extent 1919 px → 913.8 px/in)","method":"height of the traced outline (tools/trace.py); the top plan's extent across the rifle, from the clamp screw's head (left) to the windage knob's outer face (right): both stand out of the body's sides. ± covers the length's last digit and a design patent's fidelity","via":"harvest"}}],"note":"Onboarding checklist: Manufacturer spec table."},"height_up":{"label":"Height above the rail's top, standing","kind":"length","measurements":[{"id":"patent","value":1.633,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{.hinge_above_rail} + {.arm_tip_from_hinge}","via":"harvest"}}],"note":"Not published. The arm's tip with the arm turned up square to the rail about its hinge: the patent's figures, scaled by the stowed length. Magpul's photo of it standing from behind (acc7c896d80c), scaled by the aperture's published height, reads about 1.62 by eye; it hasn't been traced."},"sight_line_above_rail":{"label":"Sight line above the rail's top (the aperture's centre, the post's tip)","kind":"length","measurements":[{"id":"magpul","value":1.42,"unit":"in","stated":"Aperture height over rail: 1.42 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MBUS Pro Sight – Rear (MAG276), Technical Specifications, Other Specs","url":"https://magpul.com/mbus-pro-sight-rear.html","retrieved":"2026-10-05","via":"harvest"}},{"id":"magpul-heading","value":1.41,"unit":"in","stated":"STOWED HEIGHT OF ONLY 0.38\" KEEPS YOUR BACKUP OUT OF SIGHT; STANDARD AR SIGHT HEIGHT (1.41” ABOVE RAIL) WHEN DEPLOYED","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MBUS Pro Sight – Rear (MAG276), a feature heading on the same page (the figure sellers still print: Wing Tactical, Primary Arms, Midwest Gun Works \"Aperture height over rail: 1.41\"\")","url":"https://magpul.com/mbus-pro-sight-rear.html","retrieved":"2026-10-05","via":"harvest"}},{"id":"patent","value":1.415,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{.hinge_above_rail} + {.aperture_from_hinge}","via":"harvest"},"note":"The patent's figures, scaled by the stowed length, with the arm turned up square to the rail: the hinge's height and the aperture's distance from the hinge. An independent check of the published figure, and of the scale."}],"adopt":{"from":"magpul","reason":"The specification table's row, which names what is measured (the aperture's height over the rail); the heading's 1.41 is the older figure and differs by its last digit. The patent, scaled by the stowed length, gives 1.415."},"note":"The aperture's centre over the rail's top with the sight standing (\"Aperture height over rail\"). Magpul's page gives it twice: 1.42 in. in its specifications and 1.41” in a feature heading; the two are within each other's last digit."},"clamp_length":{"label":"Clamp's length along the rail","kind":"length","measurements":[{"id":"patent","value":0.819,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-mbus-pro-rear db3b0b65d493 (US D704,792 S (Magpul, 'Folding rear sight for a firearm'), FIG. 5 right side elevation, folded; the patent office's copy, page 6, 300 dpi)","scaleRef":"scale from magpul-mbus-pro-rear.length = 2.1 in (x-extent 1854 px → 882.9 px/in)","method":"−x_min in y [0.03, 0.17] of the traced outline (tools/trace.py); the base along the rail: its front face to the jaws' rear end, read on the rows below the folded arm","via":"harvest"}}],"note":"Onboarding checklist: A straight side view scaled by a published size: the base's two ends. `clamp_rear` and `clamp_front` read it (half each way about the frame's origin)."},"small_aperture_d":{"label":"Small aperture's diameter","kind":"length","measurements":[{"id":"magpul","value":0.07,"unit":"in","stated":"Small aperture dia.: 0.07 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MBUS Pro Sight – Rear (MAG276), Technical Specifications, Other Specs","url":"https://magpul.com/mbus-pro-sight-rear.html","retrieved":"2026-10-05","via":"harvest"}}]},"large_aperture_d":{"label":"Large aperture's diameter","kind":"length","measurements":[{"id":"magpul","value":0.19,"unit":"in","stated":"Large aperture dia.: 0.19 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MBUS Pro Sight – Rear (MAG276), Technical Specifications, Other Specs","url":"https://magpul.com/mbus-pro-sight-rear.html","retrieved":"2026-10-05","via":"harvest"}}]},"clamp_below_rail":{"label":"Clamp's jaws below the rail's top","kind":"length","measurements":[{"id":"patent","value":0.211,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-mbus-pro-rear 5159aa124947 (US D704,792 S, Magpul, FIG. 3 front elevation, folded; the patent office's copy, page 5, 300 dpi)","scaleRef":"the figure's width as the plan's (.width, itself by the stowed length): 1288 px, 922.0 px/in","method":"the channel's roof between the jaws (row 1265, stroke centre) to the fixed jaw's hook bottom (row 1459.5): 194.5 px","via":"harvest"}}],"note":"Sets the rail's top in the side and end views. The channel's roof is the lower of two parallel lines (the upper, 11 px above, is the break on its front edge); the clamp screw's lowest line is 0.12 in below it, the depth of a rail's slot (std.picatinny.slot_depth, 0.118)."},"clamp_bottom_y":{"label":"Clamp's bottom in the sight's frame (y, the rail's top is 0)","kind":"length","measurements":[{"id":"derived","value":-0.211,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"-{.clamp_below_rail}","via":"harvest"},"note":"Where the side and end profiles' origin (the jaws' bottom) sits in the part frame."}]},"front_x":{"label":"Base's front face ahead of the clamp's middle (x)","kind":"length","measurements":[{"id":"derived","value":0.409,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{.clamp_length} / 2","via":"harvest"},"note":"Where the side and plan profiles' origin (the base's front face) sits in the part frame."}]},"knob_face_z":{"label":"Windage knob's outer face from the sight's centre line (z, to the rifle's right)","kind":"length","measurements":[{"id":"patent","value":0.74,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-mbus-pro-rear f9854fd2c2a8 (US D704,792 S, Magpul, FIG. 7 top plan, folded; the patent office's copy, page 7, 300 dpi)","scaleRef":"the figure's own length as the stowed length (.length): 1919 px, 913.8 px/in","method":"the arm's centre line (column 1209: the aperture's rings and the logo's ring fitted, the arm's outline mirrored) to the knob's outer face (column 1885.5, stroke centre): 676.5 px. The front elevation reads 0.740 (the index rib's middle, column 1331, to the knob's face, column 649, at 922.0 px/in) and the bottom plan 0.741","via":"harvest"}}],"note":"The centre line is the arm's: the aperture's and the logo's centres and the knuckle's middle in the plan, the index rib's and the body's middle in the front elevation. The middle between the jaws' apexes is 0.01 in nearer the knob (the loose bar is drawn 0.03 in open). The clamp screw's head stands as far to the left as the width leaves: 0.657 in."},"hinge_above_rail":{"label":"Hinge's axis above the rail's top","kind":"length","measurements":[{"id":"patent","value":0.187,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-mbus-pro-rear db3b0b65d493 (US D704,792 S, Magpul, FIG. 5 right side elevation, folded; the patent office's copy, page 6, 300 dpi)","scaleRef":"the figure's own length as the stowed length (.length): 1854 px, 882.9 px/in","method":"the knob's centre (a circle fitted through its lobes' tips: row 795.5 on the sheet, rms 1.3 px) above the jaws' bottom (row 1147): 351.5 px, 0.398 in, less clamp_below_rail (0.211). The front elevation reads 0.187 (the knob's middle, row 1093, above the channel's roof, row 1265, at 922.0 px/in)","via":"harvest"}}],"note":"The windage screw is the hinge: the knob's centre in the side elevation."},"hinge_behind_front":{"label":"Hinge's axis behind the base's front face","kind":"length","measurements":[{"id":"patent","value":0.654,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-mbus-pro-rear db3b0b65d493 (US D704,792 S, Magpul, FIG. 5 right side elevation, folded; the patent office's copy, page 6, 300 dpi)","scaleRef":"the figure's own length as the stowed length (.length): 1854 px, 882.9 px/in","method":"the knob's centre (column 1378.0 on the sheet) behind the front face (column 800.5): 577.5 px. The plan reads 0.656 (the knob's middle, 1368.5, behind the front face, 769, at 913.8 px/in)","via":"harvest"}}]},"aperture_from_hinge":{"label":"Aperture's centre from the hinge's axis (along the arm)","kind":"length","measurements":[{"id":"patent","value":1.228,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-mbus-pro-rear f9854fd2c2a8 (US D704,792 S, Magpul, FIG. 7 top plan, folded; the patent office's copy, page 7, 300 dpi)","scaleRef":"the figure's own length as the stowed length (.length): 1919 px, 913.8 px/in","method":"the aperture's centre (its rings fitted: row 2490.9 on the sheet, rms 0.5 px) behind the hinge's axis (the knob's and the thread's middle, row 1368.5): 1122.4 px. The innermost ring is 65.1 px across, 0.071 in: the small aperture Magpul gives as 0.07","via":"harvest"}}],"note":"With hinge_above_rail this is the sight line standing, if the arm stands square to the rail: 1.415 in, against Magpul's 1.42 (and 1.41)."},"arm_tip_from_hinge":{"label":"Arm's tip from the hinge's axis","kind":"length","measurements":[{"id":"patent","value":1.446,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-mbus-pro-rear db3b0b65d493 (US D704,792 S, Magpul, FIG. 5 right side elevation, folded; the patent office's copy, page 6, 300 dpi)","scaleRef":"the figure's own length as the stowed length (.length): 1854 px, 882.9 px/in","method":"the folded arm's rear tip (column 2654.5 on the sheet) behind the knob's centre (1378.0): 1276.5 px. The plan reads 1.443 (2687 less 1368.5, at 913.8 px/in)","via":"harvest"}}]},"knob_top_above_rail":{"label":"Windage knob's top above the rail's top","kind":"length","measurements":[{"id":"patent","value":0.432,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-mbus-pro-rear db3b0b65d493 (US D704,792 S, Magpul, FIG. 5 right side elevation, folded; the patent office's copy, page 6, 300 dpi)","scaleRef":"the figure's own length as the stowed length (.length): 1854 px, 882.9 px/in","method":"the knob's circle (through its lobes' tips, r 215.9 px, 0.2445 in) above its centre: hinge_above_rail + 0.2445. The front elevation reads 0.425 (the knob's top, row 873, above the roof, row 1265)","via":"harvest"}}],"note":"The folded sight's highest point, off to the right of its centre line: 0.05 in over the stowed height Magpul gives."},"relief_depth":{"label":"Depth of the shallow recesses drawn (the logo's panel, the plate's window, the pockets)","kind":"length","measurements":[{"id":"photo","value":0.03,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-mbus-pro-rear 0a10cecc568a (Dirty Bird's copy of Magpul's studio photo, the sight standing, from the front and above, 2000 x 2000)","scaleRef":"the logo panel's own narrow end, 0.243 in in the patent's plan, 205 px across in the photo (844 px/in); its 0.452 in length shows 300 px, so the face is seen from about 38 degrees above its normal","method":"the panel's upper wall shows 35 ± 8 px tall: 0.067 in if the wall is square to the face, 0.030 if it slopes at 45 degrees, 0.011 if it slopes as far as the patent's double line draws its rim (0.044 in). The middle reading, ± the spread","via":"harvest"}}],"note":"No orthographic view gives a recess's depth. One oblique product photo bounds the logo panel's: this figure is used for every recess the model cuts, and the pockets between the ribs on the real arm are deeper than it."},"knob_lobes":{"label":"Lobes round the windage knob","kind":"count","measurements":[{"id":"patent","value":10,"unit":"count","source":{"type":"photo","photo":"references/magpul-mbus-pro-rear db3b0b65d493 (US D704,792 S, Magpul, FIG. 5 right side elevation, folded; the patent office's copy, page 6, 300 dpi)","scaleRef":"none: a count","method":"the knob's outline on rays from its centre: lobes (r 216 to 218 px) and gaps (r 199 to 200 px) alternate every 36 degrees over the clear arc (three whole periods): ten to the turn, one of them pointing straight forward","via":"harvest"}}]},"screw_behind_front":{"label":"Clamp screw's axis behind the base's front face","kind":"length","measurements":[{"id":"patent","value":0.237,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-mbus-pro-rear db3b0b65d493 (US D704,792 S, Magpul, FIG. 5 right side elevation, folded; the patent office's copy, page 6, 300 dpi)","scaleRef":"the figure's own length as the stowed length (.length): 1854 px, 882.9 px/in","method":"the centre of the boss the screw ends in (four rings fitted, their centres within 3 px: column 1010 on the sheet) behind the front face (column 800.5): 209.5 px","via":"harvest"}}],"note":"The screw crosses the rail's channel with its lower half below the rail's top (0.12 in, a slot's depth): it is what sits in a rail's slot. The plan's reading through the screw head's middle is 0.247."}}},{"subject":"magpul-mlok-aluminum-rail-section-3-slot","title":"Magpul M-LOK Aluminum Rail, 3 Slots (MAG580)","dimensions":{"length":{"label":"Overall length (along the handguard)","kind":"length","measurements":[{"id":"pa-underside","value":1.576,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-3-slot 44402d1df236 (Primary Arms, MAG580_02.jpg, 2200 x 1467: its underside, square on)","scaleRef":"its two through holes (circles fitted to their white: 618.7 and 1579.8 px), the M-LOK interval apart (20 mm: the screws over the first and third grooves), at the base's own plane: 1220.6 px to the inch","method":"the base's outline end to end along the line through the holes: 137 to 2060 px (1924 px)","via":"harvest"}},{"id":"pa-plan","value":1.578,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-3-slot bcda799c1d3e (Primary Arms, MAG580_01.jpg, 2200 x 1467: from above, square on, no screws)","scaleRef":"its two through holes (621.8 and 1582.1 px) the M-LOK interval apart, the white seen through each bounded at the base","method":"the base's outline end to end: 138 to 2062 px (1925 px). The base and the holes are in one plane in both of Primary Arms' views: they agree to 0.002 in","via":"harvest"}},{"id":"magpul-plan","value":1.563,"unit":"in","pm":0.014,"source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-3-slot fc1143e5357e (Magpul, 580_2, 700 x 525: from above, square on, screws in)","scaleRef":"its two counterbores' centres (circles fitted to their dark discs: 223.7 and 467.8 px) as two standard pitches: 309.8 px to the inch, at the rail's top","method":"the base's outline end to end (tools/trace.py: 1.563 in). Scaled at the rail's top, 0.24 in nearer the lens than the base whose tips the outline's ends are: short by that much perspective (the seven-slot's photo from above shows it, its through holes 1.8% inside its grooves)","via":"harvest"}},{"id":"mgw","value":1.5,"unit":"in","pm":0.0625,"stated":"The overall length of this rail is 1-1/2\".","source":{"type":"spec","publisher":"retailer","name":"Midwest Gun Works, Magpul Aluminum M-LOK Rail Section, 3 Slots (MAG580)","url":"https://www.midwestgunworks.com/page/mgwi/prod/mag580","retrieved":"2026-10-29","via":"harvest"},"note":"A fraction to the sixteenth: ± half of it."}],"adopt":{"from":"pa-underside","reason":"The base end to end at the scale of its own holes in the base's plane, seen square; Primary Arms' view from above, the other side of the same plane, agrees to 0.002 in. Magpul's own photo from above is scaled at the rail's top and reads 0.013 short; Magpul's \"max overall length of 1.6\" is a bound (max_length) the part is under; Midwest Gun Works' 1-1/2\" is a round figure."},"note":"The base's length, tip to tip of its arched ends: its three slots on the standard's pitch and an end block of about 0.39 in at each end. The rail's top is shorter by the two end bevels (end_bevel_run)."},"max_length":{"label":"Maximum overall length, as Magpul states it","kind":"length","measurements":[{"id":"gis","value":1.6,"unit":"in","stated":"MAG580 - 3 Slots, max overall length of 1.6”","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, M-LOK Aluminum Rail Sections (GIS sheet, MAG580-MAG583_M-LOK_Aluminum_Rail_Sections_GIS_01.pdf)","url":"https://magpul.com/media/wysiwyg/GIS/MAG580-MAG583_M-LOK_Aluminum_Rail_Sections_GIS_01.pdf","retrieved":"2026-10-29","via":"harvest"}}],"note":"A bound, not the length: the test holds the length under it."},"height":{"label":"Height (its rail's top above the handguard's face it sits on)","kind":"length","measurements":[{"id":"line","value":0.24,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{magpul-mlok-aluminum-rail-section-5-slot.height}","basis":"The line's section: Magpul's sheet makes the four lengths one product (\"M-LOK Aluminum Rail Sections ... Machined from milspec-anodized aluminum\", MAG580 to MAG583), and this length's photos have the same head, the same arches and the same counterbores as the five-slot's (its teeth 0.832 in across, its counterbores 0.37, its end blocks 0.395). Read on the five-slot (Midwest Gun Works' oblique photo, through a camera fitted to its teeth, checked on a second feature of them).","via":"harvest"}},{"id":"mgw-oblique","value":0.21,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-3-slot fdd99bf92a37 (Midwest Gun Works, MAG580.jpg, 1500 x 1301: from above its near side, its hardware in front of it)","scaleRef":"an orthographic camera fitted to its own teeth: one pitch between its two teeth's near top corners (555, 605) and (765, 580); across, the rear tooth's top from its near corner to its far end (485, 340) as the flat and the far bevel (0.66 to 0.75 in)","method":"the rear tooth's near top edge (600, 603) to the base's near edge under it (600, 700): 96.3 px across the rail's direction: 0.20 to 0.22 in with the body under the head the lower gauge line's width. The camera puts the tooth's upper bevel 68.6 px deep where the photo has its near face about 74: the picks are good to a few pixels, the ±","via":"harvest"}}],"adopt":{"from":"line","reason":"The line's figure, read on the five-slot with a check on the fit; this length's own photo reads it within its ±."},"note":"The line's figure, with the reason in its source; its own oblique photo agrees within its ±."},"width":{"label":"Width (side to side, at its widest)","kind":"length","measurements":[{"id":"std","value":0.835,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.picatinny.top_width}","via":"harvest"},"note":"The head's widest is the standard's: Magpul, \"various 1913 Picatinny spec rail-mounted accessories\"."},{"id":"plan","value":0.832,"unit":"in","pm":0.011,"source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-3-slot fc1143e5357e (Magpul, from above)","scaleRef":"its counterbores two standard pitches apart, as for length","method":"the outline across at its teeth (tools/trace.py reports 0.832)","via":"harvest"}}],"adopt":{"from":"std","reason":"The standard's head; the photo from above reads it within its ±, a check on the photo's scale."}},"neck_width":{"label":"Width of the base's flat face (the body's foot, on the hand guard's face)","kind":"length","measurements":[{"id":"underside","value":0.603,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-3-slot 44402d1df236 (Primary Arms, MAG580_02.jpg: its underside, square on)","scaleRef":"its two through holes the M-LOK interval apart, in the base's plane: 1220.6 px to the inch","method":"the base's flat face between the two lit creases that run its whole length either side (rows 362 and 1098 at columns 400 and 450, 370 and 1107 at 1900, 376 and 1103 at 1350: 736 px), the teeth's widest standing out past them to the silhouette (0.82 in). The faces outside the creases, between the base and the head, show the same tone from below: which way they lean isn't read; drawn as the head's lower faces carried on at 45 degrees, which reach this width 0.228 in under the rail's top","via":"harvest"}}],"note":"The section under the head: the head's lower 45 degree faces carried on past the lower gauge line until they are this wide (0.228 in under the rail's top), and upright from there to the base, as the clamps' hooks need room under the head (rail-sections.test.ts) and as the photos of the underside show the base: narrower than the head by 0.11 in each side. Until 2026-10-29 the body was drawn upright at the lower gauge line's width (.748), an assumption, and three clamps' hooks stood in it. Midwest Gun Works' photos from above show a dark band 30 px deep under the head's widest on the near side, which a body undercut so far shows only as its shadow on the white ground: said in height's note."},"rail_slots":{"label":"Rail slots","kind":"count","measurements":[{"id":"name","value":3,"unit":"count","stated":"M-LOK® Aluminum Rail, 3 Slots","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, M-LOK® Aluminum Rail, 3 Slots (MAG580)","url":"https://magpul.com/m-lokaluminumrail-3slots.html","retrieved":"2026-10-29","via":"harvest"}},{"id":"mgw","value":3,"unit":"count","stated":"Magpul Aluminum M-LOK Rail Section, 3 Slots","source":{"type":"spec","publisher":"retailer","name":"Midwest Gun Works, Magpul Aluminum M-LOK Rail Section, 3 Slots (MAG580)","url":"https://www.midwestgunworks.com/page/mgwi/prod/mag580","retrieved":"2026-10-29","via":"harvest"}}],"adopt":{"from":"name","reason":"Magpul's name for it; counted on its photo from above (three grooves, two teeth between them and an end block at each end)."}},"rail_slot0_x":{"label":"Rear rail slot's centre ahead of the part's rear end","kind":"length","measurements":[{"id":"pa-underside","value":0.395,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-3-slot 44402d1df236 (Primary Arms, its underside, square on)","scaleRef":"its through holes the M-LOK interval apart, in the base's plane, as for length","method":"the base's tip to the near hole's centre along the line through the holes: 481.7 px (0.3946 in); the other end 0.3934","via":"harvest"}},{"id":"magpul-plan","value":0.388,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-3-slot fc1143e5357e (Magpul, from above)","scaleRef":"its counterbores two standard pitches apart, at the rail's top","method":"the rear end of the base's outline behind the first groove's centre (tools/trace.py); short by the base's perspective, as for length","via":"harvest"}}],"adopt":{"from":"pa-underside","reason":"The base's own plane, square on, at the scale of the holes in it; the photo from above at the top's scale reads it within the two readings' ±."}},"end_bevel_run":{"label":"The end bevel's run: from the base's tip in to the bevel's top edge (along the part)","kind":"length","measurements":[{"id":"plan","value":0.14,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-3-slot fc1143e5357e (Magpul, from above)","scaleRef":"its counterbores two standard pitches apart, as for length","method":"rows 200 and 340, each end: the base's edge to the bevel's top edge, where the bevel's lighter grey gives way to the flat's (43.5, 42, 42.5 and 42.5 px: 0.136 to 0.140 in). On the centre line the two ends read 39.5 and 52.5 px, the edge there less sharp in the light","via":"harvest"}}],"note":"Magpul: \"beveled ends to reduce snagging\". The bevel runs round the arched end at one width, from the base up to the rail's top."},"screw_count":{"label":"Screws (and T-nuts) it is held by","kind":"count","measurements":[{"id":"mgw","value":2,"unit":"count","stated":"Included with this premium piece are 2 cammed T-nuts and 2 recoil/impact mitigation lugs","source":{"type":"spec","publisher":"retailer","name":"Midwest Gun Works, Magpul Aluminum M-LOK Rail Section, 3 Slots (MAG580)","url":"https://www.midwestgunworks.com/page/mgwi/prod/mag580","retrieved":"2026-10-29","via":"harvest"}},{"id":"photo","value":2,"unit":"count","source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-3-slot fc1143e5357e and aaded4c10e6e","scaleRef":"none: a count","method":"two counterbores, each with its screw, in the photo from above; two counterbores with their through holes in Magpul's studio photo","via":"harvest"}}],"adopt":{"from":"mgw","reason":"The seller's sentence, counted on two photos."}},"screw_step":{"label":"Rail pitches from one screw to the next","kind":"count","measurements":[{"id":"plan","value":2,"unit":"count","source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-3-slot fc1143e5357e (Magpul, from above)","scaleRef":"its grooves, 120.75 px apart","method":"the counterbores' fitted centres (223.7 and 467.8 px) on the first and the third grooves' dark bands' middles (224.5 and 466 px): two pitches, 20 mm, the M-LOK interval","via":"harvest"}}],"note":"The first screw stands in the first groove's floor, on its centre (rail_slot0_x). Its two T-nuts are the M-LOK interval apart: both in one slot."},"lugs":{"label":"M-LOK slots its T-nuts span","kind":"count","measurements":[{"id":"derived","value":1,"unit":"count","source":{"type":"derived","basis":"Two T-nuts (Midwest Gun Works) on two screws the M-LOK interval apart (screw_step: two rail pitches, 20 mm): both in one slot, one in each half of it, as an accessory with nuts 20 mm apart goes (Magpul's M-LOK FAQ: \"M-LOK accessories can be direct mounted entirely within a slot\"). Magpul's photo of it on a hand guard (76328379992b) has both screws over one slot of the face.","via":"harvest"}}]},"lug_x":{"label":"Its seat on the M-LOK face: the centre of the M-LOK slot its rear T-nut is in, ahead of its rear end","kind":"length","measurements":[{"id":"rear-nut","value":0.789,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{.rail_slot0_x} + {std.mlok.interval} / 2","basis":"The rear T-nut is on the rear screw, which stands on the first groove's centre (screw_step); the nut sits in the rear half of its M-LOK slot, half the M-LOK interval behind the slot's centre (the category's seat, data/categories/rail_section.yaml, as the polymer sections have it): what an M-LOK position places is that slot's centre.","via":"harvest"}}],"note":"Its two T-nuts are the M-LOK interval apart (the screws over the first and the third grooves): one in each half of one slot, as a hand stop's two lugs are, and that slot's centre is the second groove's, the part's middle."},"reach_inside":{"label":"Reach inside the handguard (below the mounting face, tightened)","kind":"length","measurements":[],"note":"Not published: Magpul's M-LOK tips sheet sets the nut's top level with the recoil lug's bottom edge and gives neither's size."},"counterbore_d":{"label":"The screws' counterbores, across","kind":"length","measurements":[{"id":"plan","value":0.37,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-3-slot fc1143e5357e (Magpul, from above)","scaleRef":"its counterbores two standard pitches apart, as for length","method":"circles fitted to the two counterbores' dark discs: 57.4 px of radius each (0.371 in across); the rear one 166 to 282 px across its centre's rows (0.374)","via":"harvest"}}]},"screw_head_d":{"label":"The screws' button heads, across","kind":"length","measurements":[{"id":"plan","value":0.2,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-3-slot fc1143e5357e (Magpul, from above)","scaleRef":"its counterbores two standard pitches apart, as for length","method":"the lit rim of the rear head's dome in its counterbore: 191 to 254 px (63 px)","via":"harvest"}}]},"screw_seat_below_top":{"label":"How far below the rail's top the screws' heads seat (the counterbore's floor)","kind":"length","measurements":[{"id":"assumed","value":0.2,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows the counterbore's floor in profile. The heads are down in the counterbores below the grooves' floors in every photo with the screws in; their seat is put 0.04 in above the base.","via":"harvest"}}]},"screw_head_height":{"label":"The screws' button heads, high","kind":"length","measurements":[{"id":"assumed","value":0.08,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no photo on file shows a screw of it from the side; a button head about a third as high as it is wide.","via":"harvest"}}]},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"metal","value":0.25,"unit":"oz","pm":0.06,"source":{"type":"derived","basis":"The rail's own aluminium: the model's volume, 0.1581 cubic inches (pipeline/blender/magpul_mlok_aluminum_rail_section.py's manifest for this length, app/public/models/magpul-mlok-aluminum-rail-section-3-slot.json volume_in3, the screws apart), times std.density.aluminium (1.568 oz to the cubic inch: the alloy isn't stated, \"Machined from milspec-anodized aluminum\"): 0.248 oz. The ± is the height's (± 0.03 in over its length and the width under its head) and the alloy's 4%.","via":"harvest"}}],"note":"Worked out, not weighed: no page on file gives its weight. The two screws and two T-nuts it is sold with are steel and not in it (no figure for them), nor the recoil lugs under the base, which aren't drawn."}}},{"subject":"magpul-mlok-aluminum-rail-section-5-slot","title":"Magpul M-LOK Aluminum Rail, 5 Slots (MAG581)","dimensions":{"length":{"label":"Overall length (along the handguard)","kind":"length","measurements":[{"id":"plan","value":2.331,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-5-slot 9f1857805a7d (Primary Arms, MAG581_00.jpg, 2200 x 1467: from above, square on)","scaleRef":"its own first and fifth grooves' centres (629.2 and 1479.0 px, each where its two walls cross half the teeth's grey, rows 540 to 910 within 1.5 px) as four standard pitches (std.picatinny.slot_pitch): 539.2 px to the inch, at the rail's top","method":"the base's outline end to end along the centre line (tools/trace.py, spec plan-measure: 1257 px), the arches' tips: at the top's scale, short by the base's perspective (adopt)","via":"harvest"}},{"id":"pa","value":2.5,"unit":"in","stated":"Overall length: 2.5\"","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Magpul M-LOK Aluminum Rail Section - 5 Slot (MAG581)","url":"https://www.primaryarms.com/magpul-m-lok-aluminum-rail-section-5-slot-mag581","retrieved":"2026-10-29","via":"harvest"}},{"id":"mgw","value":2.6,"unit":"in","pm":0.1,"stated":"The overall length of this rail is around 2-3/5\".","source":{"type":"spec","publisher":"retailer","name":"Midwest Gun Works, Magpul Aluminum M-LOK Rail Section, 5 Slots (MAG581)","url":"https://www.midwestgunworks.com/page/mgwi/prod/mag581","retrieved":"2026-10-29","via":"harvest"}},{"id":"magpul-oblique","value":2.382,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-5-slot 5a9a8791511f (Magpul's studio photo, 1200 x 1200, from high over one end, no screws)","scaleRef":"its two through holes (circles fitted to their white: 455.0, 668.5 and 760.5, 508.1 px), four standard pitches apart at the base's plane: 218.9 px to the inch along the line through them","method":"the base's outline along that line: 521.4 px. The same studio's photos of the seven- and nine-slot lengths read their lengths this way within 0.1% of Primary Arms' square views of them at their holes' scale; the three-slot's, its holes only 166 px apart, 2% long: the ±","via":"harvest"}}],"adopt":{"from":"magpul-oblique","reason":"The base's length at the scale of the holes in the base's own plane. Primary Arms' photo from above (plan) has its screws in and no hole to see: it is scaled by its grooves at the rail's top, 0.24 in nearer the lens than the base whose tips the outline's ends are, and reads short (the seven-slot's photo from the same seller has its through holes 1.8% inside its grooves; with that, 2.331 is 2.37). Magpul's figure is a maximum (max_length); Primary Arms' 2.5 repeats it; Midwest Gun Works' \"around 2-3/5\" is a round figure over it. Its end blocks then match the three-, seven- and nine-slot's (0.39 to 0.40 in) as read square on their bases."},"note":"The base's length, tip to tip of its arched ends. The rail's top is shorter by the two end bevels (end_bevel_run)."},"max_length":{"label":"Maximum overall length, as Magpul states it","kind":"length","measurements":[{"id":"gis","value":2.5,"unit":"in","stated":"MAG581 - 5 Slots, max overall length of 2.5”","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, M-LOK Aluminum Rail Sections (GIS sheet, MAG580-MAG583_M-LOK_Aluminum_Rail_Sections_GIS_01.pdf)","url":"https://magpul.com/media/wysiwyg/GIS/MAG580-MAG583_M-LOK_Aluminum_Rail_Sections_GIS_01.pdf","retrieved":"2026-10-29","via":"harvest"}}],"note":"A bound, not the length: the test holds the length under it."},"height":{"label":"Height (its rail's top above the handguard's face it sits on)","kind":"length","measurements":[{"id":"mgw-oblique","value":0.24,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-5-slot 88793a58f016 (Midwest Gun Works, MAG581.jpg, 1500 x 1500: from above its near side, the hardware beside it)","scaleRef":"an orthographic camera fitted to the rail's own teeth: along it, the standard's pitch on the near top edge (tooth to tooth 206.5 px, three pitches, on the line through (60, 920) at 11.0 degrees); across it, a tooth's top flat (the standard's .656, 297 px from its near corner (467, 985) to its far one (585, 712)); upright, from the two by the rotation's orthogonality (549 to 554 px to the inch, the up axis 62.7 to 67.5 px across and 344 to 351 down to the inch). Checked: the upper 45 degree face of a tooth, which the camera puts 68.7 to 69.4 px deep across the edge, reads 70.2 (column 515: 991.5 to 1063)","method":"column 515 through a tooth: the top flat's near edge at 991.5 px, the bevel's band to 1063, the side to the background at 1093.5: 100.1 px across the edge's direction from the flat's near edge to the base's near edge. Through the camera that is 0.24 in of height with the band's foot taken for the base's near edge at the lower gauge line's width (.748); 0.21 if 0.79 across (the plan's reading at the grooves) and 0.18 if as wide as the head: the ± covers the first two. With the base 0.60 across (neck_width, read from below on the three- and nine-slot) and the head's lower faces carried on at 45 degrees down to it, the base's edge doesn't show from this camera, and the band's foot (a sharp edge against the white, 45 to 253 in 2 px) would be something else: a face this section doesn't have, or the part's shadow on the ground. The neck's foot that the undersides and the 45 degree faces give, 0.228 in under the top, is inside the ±","via":"harvest"}}],"note":"The rail's top above the base's underside, which bears on the hand guard's face (the recoil lugs under it go into the slots and aren't counted). Read on one photo, through a camera fitted to the part's own teeth, whose fit holds a second feature of them to 1 to 2 percent."},"width":{"label":"Width (side to side, at its widest)","kind":"length","measurements":[{"id":"std","value":0.835,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.picatinny.top_width}","via":"harvest"},"note":"The head's widest is the standard's: Magpul, \"various 1913 Picatinny spec rail-mounted accessories\"."},{"id":"plan","value":0.825,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-5-slot 9f1857805a7d (Primary Arms, from above)","scaleRef":"its grooves at the standard's pitch, as for length","method":"the outline across at its teeth: rows 505 to 949 (445 px; tools/trace.py reports 0.825)","via":"harvest"},"note":"A black edge on white reads a few pixels thin: 0.01 in under the standard's .835 -.005 here, as the teeth's own blur."}],"adopt":{"from":"std","reason":"The standard's head; the photo from above reads it within its ±."},"note":"Nothing of it is wider than the head: the outline from above is the teeth's widest along both sides, and 0.02 in inside it at each groove."},"neck_width":{"label":"Width of the base's flat face (the body's foot, on the hand guard's face)","kind":"length","measurements":[{"id":"line","value":0.602,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"({magpul-mlok-aluminum-rail-section-3-slot.neck_width} + {magpul-mlok-aluminum-rail-section-9-slot.neck_width}) / 2","basis":"The line's base, read square from below on the three- and nine-slot lengths (Primary Arms' photos of their undersides: 0.603 and 0.60 in between the creases along it); no photo of this length shows its underside.","via":"harvest"}}],"note":"The section under the head: the head's lower 45 degree faces carried on past the lower gauge line until they are this wide (0.227 in under the rail's top), and upright from there to the base, as the clamps' hooks need room under the head (rail-sections.test.ts) and as the photos of the underside show the base: narrower than the head by 0.11 in each side. Until 2026-10-29 the body was drawn upright at the lower gauge line's width (.748), an assumption, and three clamps' hooks stood in it. Midwest Gun Works' photos from above show a dark band 30 px deep under the head's widest on the near side, which a body undercut so far shows only as its shadow on the white ground: said in height's note."},"rail_slots":{"label":"Rail slots","kind":"count","measurements":[{"id":"name","value":5,"unit":"count","stated":"M-LOK® Aluminum Rail, 5 Slots","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, M-LOK® Aluminum Rail, 5 Slots (MAG581)","url":"https://magpul.com/m-lokaluminumrail-5slots.html","retrieved":"2026-10-29","via":"harvest"}},{"id":"pa","value":5,"unit":"count","stated":"5 slots of M1913 Picatinny rail","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Magpul M-LOK Aluminum Rail Section - 5 Slot (MAG581)","url":"https://www.primaryarms.com/magpul-m-lok-aluminum-rail-section-5-slot-mag581","retrieved":"2026-10-29","via":"harvest"}}],"adopt":{"from":"name","reason":"Magpul's name for it; counted on the photo from above too (five grooves, four teeth between them and an end block at each end)."}},"rail_slot0_x":{"label":"Rear rail slot's centre ahead of the part's rear end","kind":"length","measurements":[{"id":"magpul-oblique","value":0.403,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-5-slot 5a9a8791511f (Magpul's studio photo, from high over one end)","scaleRef":"its through holes four standard pitches apart, at the base's plane, as for length","method":"the base's tip to the near hole along the line through the holes: 0.4033 in; the far end 0.4022","via":"harvest"}},{"id":"photo","value":0.381,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-5-slot 9f1857805a7d (Primary Arms' MAG581 from above, 2200 x 1467, on white)","scaleRef":"its first and fifth grooves four standard pitches apart (539.2 px/in), at the rail's top","method":"−x_min of the traced outline (tools/trace.py): the base's rear tip behind the first groove's centre. The tip is 0.24 in further from the lens than the groove and stands in toward the picture's centre by about 10 px at the seven-slot photo's perspective: 0.400 with that","via":"harvest"}}],"adopt":{"from":"magpul-oblique","reason":"Read at the scale of the holes in the base's own plane, as the three-, seven- and nine-slot's end blocks are (0.395 to 0.40 in); Primary Arms' photo from above reads the tip at the top's scale, 0.02 short."}},"end_bevel_run":{"label":"The end bevel's run: from the base's tip in to the bevel's top edge (along the part)","kind":"length","measurements":[{"id":"plan","value":0.122,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-5-slot 9f1857805a7d (Primary Arms, from above)","scaleRef":"its grooves at the standard's pitch, as for length","method":"on the centre line at the rear end, the base's tip (424 px) to the bevel's top edge, an arch concentric with the base's where the bevel's lighter grey gives way to the flat's (490 px): 66 px","via":"harvest"}},{"id":"installed","value":0.13,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-5-slot 4a11af353bb8 (Magpul, on a hand guard's side face, square on)","scaleRef":"its own two screws, four rail pitches apart (237 px)","method":"its lit top, which ends at the bevel's top edge against the dark hand guard, reaches 0.64 of a pitch past each screw (37.7 px); the base reaches 0.966 of a pitch past it in the plan view: 0.33 of a pitch","via":"harvest"}}],"adopt":{"from":"plan","reason":"The square view from above; the installed photo agrees within the two readings' ±."},"note":"Magpul: \"beveled ends to reduce snagging\". The bevel runs round the arched end at one width (its top edge is an arch inside the base's), from the base up to the rail's top: about 63 degrees from the base at this height."},"screw_count":{"label":"Screws (and T-nuts) it is held by","kind":"count","measurements":[{"id":"mgw","value":2,"unit":"count","stated":"Included with this premium piece are 2 cammed T-nuts and 2 recoil/impact mitigation lugs","source":{"type":"spec","publisher":"retailer","name":"Midwest Gun Works, Magpul Aluminum M-LOK Rail Section, 5 Slots (MAG581)","url":"https://www.midwestgunworks.com/page/mgwi/prod/mag581","retrieved":"2026-10-29","via":"harvest"}},{"id":"photo","value":2,"unit":"count","source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-5-slot 88793a58f016 and 9f1857805a7d","scaleRef":"none: a count","method":"two T-nuts and two button-head screws beside it in Midwest Gun Works' photo; two counterbores, each with its screw, in the photo from above","via":"harvest"}}],"adopt":{"from":"mgw","reason":"The seller's sentence, counted on two photos."}},"screw_step":{"label":"Rail pitches from one screw to the next","kind":"count","measurements":[{"id":"plan","value":4,"unit":"count","source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-5-slot 9f1857805a7d (Primary Arms, from above)","scaleRef":"its grooves at the standard's pitch, as for length","method":"the counterbores' circles fitted to their dark discs (centres 629.0 and 1480 px) stand on the first and the fifth grooves' centres (629.2 and 1479.0): four pitches, 1.575 in, which is the M-LOK slot pitch (40 mm, 1.5748 in) to 0.01%","via":"harvest"}}],"note":"The first screw stands in the first groove's floor, on its centre (rail_slot0_x)."},"lugs":{"label":"M-LOK slots its T-nuts span","kind":"count","measurements":[{"id":"derived","value":2,"unit":"count","source":{"type":"derived","expr":"{.screw_count}","basis":"One T-nut on each screw (two of each, Midwest Gun Works), the screws one M-LOK slot pitch apart (screw_step: four rail pitches, 40 mm): one T-nut in each of two slots side by side. Magpul's photo of it on a hand guard's side face (4a11af353bb8) has each screw over a slot of the face's rows above and below it.","via":"harvest"}}]},"lug_x":{"label":"Its seat on the M-LOK face: the centre of the M-LOK slot its rear T-nut is in, ahead of its rear end","kind":"length","measurements":[{"id":"rear-nut","value":0.797,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{.rail_slot0_x} + {std.mlok.interval} / 2","basis":"The rear T-nut is on the rear screw, which stands on the first groove's centre (screw_step); the nut sits in the rear half of its M-LOK slot, half the M-LOK interval behind the slot's centre (the category's seat, data/categories/rail_section.yaml, as the polymer sections have it): what an M-LOK position places is that slot's centre.","via":"harvest"}}],"note":"Its two T-nuts are one M-LOK slot pitch apart (the screws over the first and the fifth grooves): each in the rear half of its slot. Magpul's photo of it on a hand guard's side face (4a11af353bb8) has its screws over the face's slots' centres, half an interval ahead of this seat: which half a nut is in isn't published, and the app's places, half a slot apart, are the same either way."},"reach_inside":{"label":"Reach inside the handguard (below the mounting face, tightened)","kind":"length","measurements":[],"note":"Not published: Magpul's M-LOK tips sheet sets the nut's top level with the recoil lug's bottom edge (\"with the highest edge of the T-Nut even with the bottom edge of the recoil lug\") and gives neither's size."},"counterbore_d":{"label":"The screws' counterbores, across","kind":"length","measurements":[{"id":"plan","value":0.37,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-5-slot 9f1857805a7d (Primary Arms, from above)","scaleRef":"its grooves at the standard's pitch, as for length","method":"the rear counterbore across, on the rows of its centre: 530 to 730 px (200 px; its dark disc's box 202 px). A circle fitted to the dark disc reads 96.8 px of radius (0.359 in), pulled in where the screw's lit rim breaks the disc","via":"harvest"}}],"note":"Each cuts the end block and the first tooth either side of its groove (both photos)."},"screw_head_d":{"label":"The screws' button heads, across","kind":"length","measurements":[{"id":"plan","value":0.21,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-5-slot 9f1857805a7d (Primary Arms, from above)","scaleRef":"its grooves at the standard's pitch, as for length","method":"the dome of the head down in the rear counterbore: its lit rim round the hex socket 0.16 to 0.25 in across (87 to 135 px), its edge lost against the counterbore's dark wall; the ± covers both","via":"harvest"}}]},"screw_seat_below_top":{"label":"How far below the rail's top the screws' heads seat (the counterbore's floor)","kind":"length","measurements":[{"id":"assumed","value":0.2,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows the counterbore's floor in profile. The heads are down in the counterbores below the grooves' floors in every photo with the screws in; their seat is put 0.04 in above the base.","via":"harvest"}}]},"screw_head_height":{"label":"The screws' button heads, high","kind":"length","measurements":[{"id":"assumed","value":0.08,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: Midwest Gun Works' photo has the two screws lying on their sides beside it but at a slant no camera has been fitted to; a button head about a third as high as it is wide.","via":"harvest"}}]},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"metal","value":0.42,"unit":"oz","pm":0.09,"source":{"type":"derived","basis":"The rail's own aluminium: the model's volume, 0.2658 cubic inches (pipeline/blender/magpul_mlok_aluminum_rail_section.py's manifest for this length, app/public/models/magpul-mlok-aluminum-rail-section-5-slot.json volume_in3, the screws apart), times std.density.aluminium (1.568 oz to the cubic inch: the alloy isn't stated, \"Machined from milspec-anodized aluminum\"): 0.417 oz. The ± is the height's (± 0.03 in over its length and the width under its head) and the alloy's 4%.","via":"harvest"}}],"note":"Worked out, not weighed: no page on file gives its weight. The two screws and two T-nuts it is sold with are steel and not in it (no figure for them), nor the recoil lugs under the base, which aren't drawn. Search results gave sellers' 2.19 and 2.24 oz for MAG581 (discovery's leads, not read on any page here): five times this aluminium, and nearer a boxed weight."}}},{"subject":"magpul-mlok-aluminum-rail-section-7-slot","title":"Magpul M-LOK Aluminum Rail, 7 Slots (MAG582)","dimensions":{"length":{"label":"Overall length (along the handguard)","kind":"length","measurements":[{"id":"blocks","value":3.162,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{.rail_slot0_x} + 6 * {std.picatinny.slot_pitch} + {.front_block}","basis":"Its 7 slots on the standard's pitch and its two end blocks as read square on its own photos, at the scale of its holes in the base's plane.","via":"harvest"}},{"id":"ky","value":3.3,"unit":"in","stated":"7 slots, 3.3\" overall length.","source":{"type":"spec","publisher":"retailer","name":"KYGunCo, Magpul M-Lok Aluminum Rail Section 7 Slots (MAG582-BLK)","url":"https://www.kygunco.com/product/magpul-mag582-blk-m-lok-aluminum-rail-section-7-slots-blk","retrieved":"2026-10-29","via":"harvest"},"note":"Magpul's maximum as the length: the same page also says \"a max overall length of 3.3\"\"."}],"adopt":{"from":"blocks","reason":"Magpul's own figure is a maximum (max_length), and the part is under it; the sellers' figures repeat that maximum. Its slots on the standard's pitch and its own end blocks, each as long as the three- and five-slot's are (0.395 and 0.403 in) within their ±."},"note":"The base's length, tip to tip of its arched ends."},"max_length":{"label":"Maximum overall length, as Magpul states it","kind":"length","measurements":[{"id":"gis","value":3.3,"unit":"in","stated":"MAG582 - 7 Slots, max overall length of 3.3”","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, M-LOK Aluminum Rail Sections (GIS sheet, MAG580-MAG583_M-LOK_Aluminum_Rail_Sections_GIS_01.pdf)","url":"https://magpul.com/media/wysiwyg/GIS/MAG580-MAG583_M-LOK_Aluminum_Rail_Sections_GIS_01.pdf","retrieved":"2026-10-29","via":"harvest"}}],"note":"A bound, not the length: the test holds the length under it."},"height":{"label":"Height (its rail's top above the handguard's face it sits on)","kind":"length","measurements":[{"id":"line","value":0.24,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{magpul-mlok-aluminum-rail-section-5-slot.height}","basis":"The line's section: Magpul's sheet makes the four lengths one product (\"M-LOK Aluminum Rail Sections ... Machined from milspec-anodized aluminum\", MAG580 to MAG583), and this length's photos have the same head, arches and counterbores as the five-slot's. Read on the five-slot (Midwest Gun Works' oblique photo, through a camera fitted to its teeth and checked on a second feature of them).","via":"harvest"}},{"id":"mgw-oblique","value":0.26,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-7-slot 34f80843acd1 (Midwest Gun Works, MAG582.jpg, 1500 x 1500: from above its near side, its hardware beside it)","scaleRef":"an orthographic camera from its own teeth: along it, the standard's pitch (tooth to tooth 160.5 to 167 px on the row 900, about 163: 414 px to the inch); across it, a groove's floor from its far edge to its near (298 px along the groove, as 0.80 to 0.82 in, what the views from above and below have the part at its grooves)","method":"along the groove from (503, 640): the floor's near edge at 357.5 px to the base's near edge, the background, at 373.5: 16 px. Through that camera, 0.26 in with the body under the head the lower gauge line's width. Sensitive to the floor's width and the camera's elevation: the ±","via":"harvest"}}],"adopt":{"from":"line","reason":"The line's figure, read on the five-slot with a check on the fit; this length's own photo reads it within its ±."},"note":"The line's figure, with the reason in its source."},"width":{"label":"Width (side to side, at its widest)","kind":"length","measurements":[{"id":"std","value":0.835,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.picatinny.top_width}","via":"harvest"},"note":"The head's widest is the standard's: Magpul, \"various 1913 Picatinny spec rail-mounted accessories\"."}]},"neck_width":{"label":"Width of the base's flat face (the body's foot, on the hand guard's face)","kind":"length","measurements":[{"id":"line","value":0.602,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"({magpul-mlok-aluminum-rail-section-3-slot.neck_width} + {magpul-mlok-aluminum-rail-section-9-slot.neck_width}) / 2","basis":"The line's base, read square from below on the three- and nine-slot lengths (Primary Arms' photos of their undersides: 0.603 and 0.60 in between the creases along it); no photo of this length shows its underside.","via":"harvest"}}],"note":"The section under the head: the head's lower 45 degree faces carried on past the lower gauge line until they are this wide (0.227 in under the rail's top), and upright from there to the base, as the clamps' hooks need room under the head (rail-sections.test.ts) and as the photos of the underside show the base: narrower than the head by 0.11 in each side. Until 2026-10-29 the body was drawn upright at the lower gauge line's width (.748), an assumption, and three clamps' hooks stood in it. Midwest Gun Works' photos from above show a dark band 30 px deep under the head's widest on the near side, which a body undercut so far shows only as its shadow on the white ground: said in height's note."},"rail_slots":{"label":"Rail slots","kind":"count","measurements":[{"id":"name","value":7,"unit":"count","stated":"M-LOK® Aluminum Rail, 7 Slots","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, M-LOK® Aluminum Rail, 7 Slots (MAG582)","url":"https://magpul.com/m-lokaluminumrail-7slots.html","retrieved":"2026-10-29","via":"harvest"}}],"note":"Magpul's name for it; counted on its studio photo (7 grooves, 6 teeth between them and an end block at each end)."},"rail_slot0_x":{"label":"Rear rail slot's centre ahead of the part's rear end","kind":"length","measurements":[{"id":"pa-plan","value":0.398,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-7-slot c475d60ec064 (Primary Arms, MAG582_00.jpg, 2200 x 1466: from above, square on, no screws)","scaleRef":"its two through holes (circles fitted to their white: 557.4 and 1652.0 px; the white seen through each is bounded at the base), six standard pitches apart at the base's plane: 463.0 px to the inch. Its grooves read 472 px to the inch at the rail's top (groove centres 549.1 and 1663.5 px): the base, 0.24 in further from the lens, 1.8% smaller","method":"the base's rear tip (373 px) to the rear hole's centre","via":"harvest"}},{"id":"magpul-oblique","value":0.404,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-7-slot 31cbf64bfda2 (Magpul's studio photo, from high over one end)","scaleRef":"its through holes six standard pitches apart at the base's plane","method":"the base's tip to the near hole along the line through the holes","via":"harvest"}}],"adopt":{"from":"pa-plan","reason":"Square on, at the scale of the holes in the base's plane; Magpul's steep photo agrees within its ±."}},"front_block":{"label":"Front end block: the last rail slot's centre to the part's front end","kind":"length","measurements":[{"id":"pa-plan","value":0.4,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-7-slot c475d60ec064 (Primary Arms, from above)","scaleRef":"as for rail_slot0_x","method":"the front hole's centre to the base's front tip (1837 px): 185 px (0.3996 in)","via":"harvest"}},{"id":"magpul-oblique","value":0.394,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-7-slot 31cbf64bfda2 (Magpul's studio photo)","scaleRef":"as for rail_slot0_x","method":"the far hole to the outline's far tip along the line through the holes","via":"harvest"}}],"adopt":{"from":"pa-plan","reason":"As for rail_slot0_x."},"note":"Within its ± of the rear one: the part is the same both ways round."},"end_bevel_run":{"label":"The end bevel's run: from the base's tip in to the bevel's top edge (along the part)","kind":"length","measurements":[{"id":"line","value":0.131,"unit":"in","pm":0.025,"source":{"type":"derived","expr":"({magpul-mlok-aluminum-rail-section-3-slot.end_bevel_run} + {magpul-mlok-aluminum-rail-section-5-slot.end_bevel_run}) / 2","basis":"The line's end, read square from above on the three- and five-slot lengths (0.14 and 0.122 in): Magpul's sheet gives all four \"beveled ends\", and this length's studio photo shows the same arch and bevel, but at a slant that doesn't separate the bevel's top edge from the flat.","via":"harvest"}}]},"screw_count":{"label":"Screws (and T-nuts) it is held by","kind":"count","measurements":[{"id":"photo","value":2,"unit":"count","source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-7-slot 31cbf64bfda2 and 837ca16d5a0a","scaleRef":"none: a count","method":"two counterbores with their through holes in Magpul's studio photo; two screws in it on a hand guard","via":"harvest"}}],"note":"No seller on file states its hardware; Midwest Gun Works says two for the three- and five-slot and three for the nine-slot, one a screw."},"screw_step":{"label":"Rail pitches from one screw to the next","kind":"count","measurements":[{"id":"photo","value":6,"unit":"count","source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-7-slot 31cbf64bfda2","scaleRef":"its grooves, counted","method":"its through holes stand in the first, seventh grooves' floors: 6 pitches apart","via":"harvest"}}],"note":"The first screw stands in the first groove's floor (rail_slot0_x)."},"lugs":{"label":"M-LOK slots its T-nuts span","kind":"count","measurements":[{"id":"derived","value":2,"unit":"count","source":{"type":"derived","basis":"Two T-nuts on two screws six rail pitches apart (60 mm, one and a half M-LOK slot pitches): one in the rear half of one slot and one in the front half of the next, the closer of the two ways M-LOK places nuts 60 mm apart (Magpul's FAQ: accessories mount \"entirely within a slot or bridging between/across slots\"). Magpul's photo of it on a hand guard is too coarse to say which halves; the app's places a slot's interval apart offer both.","via":"harvest"}}]},"lug_x":{"label":"Its seat on the M-LOK face: the centre of the M-LOK slot its rear T-nut is in, ahead of its rear end","kind":"length","measurements":[{"id":"rear-nut","value":0.792,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{.rail_slot0_x} + {std.mlok.interval} / 2","basis":"The rear T-nut is on the rear screw, which stands on the first groove's centre (screw_step); the nut sits in the rear half of its M-LOK slot, half the M-LOK interval behind the slot's centre (the category's seat, data/categories/rail_section.yaml, as the polymer sections have it): what an M-LOK position places is that slot's centre.","via":"harvest"}}],"note":"Its two T-nuts are six rail pitches apart, 60 mm (the screws over the first and the seventh grooves): the rear one in the rear half of one slot, the front one in the front half of the next. Which halves isn't published; the app's places, half a slot apart, offer both ways the nuts can go."},"reach_inside":{"label":"Reach inside the handguard (below the mounting face, tightened)","kind":"length","measurements":[],"note":"Not published: Magpul's M-LOK tips sheet sets the nut's top level with the recoil lug's bottom edge and gives neither's size."},"counterbore_d":{"label":"The screws' counterbores, across","kind":"length","measurements":[{"id":"pa-plan","value":0.369,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-7-slot c475d60ec064 (Primary Arms, from above)","scaleRef":"its grooves at the rail's top: 472 px to the inch","method":"column 557 across the rear counterbore: its dark ring from 622 to 796 px (174 px), the through hole's white inside it","via":"harvest"}}]},"screw_head_d":{"label":"The screws' button heads, across","kind":"length","measurements":[{"id":"line","value":0.205,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"({magpul-mlok-aluminum-rail-section-3-slot.screw_head_d} + {magpul-mlok-aluminum-rail-section-5-slot.screw_head_d}) / 2","basis":"Magpul's M-LOK screws, as read in the three- and five-slot lengths' counterbores from above (0.20 and 0.21 in).","via":"harvest"}}]},"screw_seat_below_top":{"label":"How far below the rail's top the screws' heads seat (the counterbore's floor)","kind":"length","measurements":[{"id":"assumed","value":0.2,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows the counterbore's floor in profile. The heads are down in the counterbores below the grooves' floors in every photo with the screws in; their seat is put 0.04 in above the base.","via":"harvest"}}]},"screw_head_height":{"label":"The screws' button heads, high","kind":"length","measurements":[{"id":"assumed","value":0.08,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no camera is fitted to a photo of its screws from the side; a button head about a third as high as it is wide.","via":"harvest"}}]},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"metal","value":0.57,"unit":"oz","pm":0.12,"source":{"type":"derived","basis":"The rail's own aluminium: the model's volume, 0.3643 cubic inches (pipeline/blender/magpul_mlok_aluminum_rail_section.py's manifest for this length, app/public/models/magpul-mlok-aluminum-rail-section-7-slot.json volume_in3, the screws apart), times std.density.aluminium (1.568 oz to the cubic inch: the alloy isn't stated, \"Machined from milspec-anodized aluminum\"): 0.571 oz. The ± is the height's (± 0.03 in over its length and the width under its head) and the alloy's 4%.","via":"harvest"}}],"note":"Worked out, not weighed: no page on file gives its weight. The two screws and two T-nuts it is sold with are steel and not in it (no figure for them), nor the recoil lugs under the base, which aren't drawn."}}},{"subject":"magpul-mlok-aluminum-rail-section-9-slot","title":"Magpul M-LOK Aluminum Rail, 9 Slots (MAG583)","dimensions":{"length":{"label":"Overall length (along the handguard)","kind":"length","measurements":[{"id":"blocks","value":3.943,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{.rail_slot0_x} + 8 * {std.picatinny.slot_pitch} + {.front_block}","basis":"Its 9 slots on the standard's pitch and its two end blocks as read square on its own photos, at the scale of its holes in the base's plane.","via":"harvest"}},{"id":"mgw","value":4.1,"unit":"in","stated":"The overall length of this rail is 4.1\".","source":{"type":"spec","publisher":"retailer","name":"Midwest Gun Works, Magpul Aluminum M-LOK Rail Section, 9 Slots (MAG583)","url":"https://www.midwestgunworks.com/page/mgwi/prod/mag583","retrieved":"2026-10-29","via":"harvest"},"note":"Magpul's maximum."}],"adopt":{"from":"blocks","reason":"Magpul's own figure is a maximum (max_length), and the part is under it; the sellers' figures repeat that maximum. Its slots on the standard's pitch and its own end blocks, each as long as the three- and five-slot's are (0.395 and 0.403 in) within their ±."},"note":"The base's length, tip to tip of its arched ends."},"max_length":{"label":"Maximum overall length, as Magpul states it","kind":"length","measurements":[{"id":"gis","value":4.1,"unit":"in","stated":"MAG583 - 9 Slots, max overall length of 4.1”","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, M-LOK Aluminum Rail Sections (GIS sheet, MAG580-MAG583_M-LOK_Aluminum_Rail_Sections_GIS_01.pdf)","url":"https://magpul.com/media/wysiwyg/GIS/MAG580-MAG583_M-LOK_Aluminum_Rail_Sections_GIS_01.pdf","retrieved":"2026-10-29","via":"harvest"}}],"note":"A bound, not the length: the test holds the length under it."},"height":{"label":"Height (its rail's top above the handguard's face it sits on)","kind":"length","measurements":[{"id":"line","value":0.24,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{magpul-mlok-aluminum-rail-section-5-slot.height}","basis":"The line's section: Magpul's sheet makes the four lengths one product (\"M-LOK Aluminum Rail Sections ... Machined from milspec-anodized aluminum\", MAG580 to MAG583), and this length's photos have the same head, arches and counterbores as the five-slot's. Read on the five-slot (Midwest Gun Works' oblique photo, through a camera fitted to its teeth and checked on a second feature of them).","via":"harvest"}},{"id":"mgw-oblique","value":0.2,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-9-slot b0cdaba292bd (Midwest Gun Works, MAG583.jpg, 1500 x 1500: from above its near side)","scaleRef":"an orthographic camera fitted to a tooth and its neighbour near the middle: one pitch between their near top corners (615, 918) and (750, 973); across, the tooth's top from its near corner to the far silhouette (899.6, 803.9) as the flat and the far bevel out to the widest (0.70 to 0.75 in)","method":"the tooth's near top edge (750, 973) to the base's near edge under it (745, 1044): 67.6 px across the rail's direction: 0.20 in with the body under the head the standard's lower gauge line's width. The photo is close (the pitch 127 to 150 px along the part), the picks good to 3 to 5 px: the ±","via":"harvest"}},{"id":"lifestyle","value":0.27,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-9-slot 32e64da8a8ac (Magpul, on an MOE SL hand guard, close and soft)","scaleRef":"a camera fitted to its teeth near its middle screw: 74.7 px a pitch along it, the top flat's 0.656 in across","method":"along a tooth: its top flat's near edge to where its side meets the hand guard's face (the start of the darkest band, its shadow): 27.5 px. Sensitive to the camera's elevation, which the flat's far edge sets only to within a few pixels: the ±","via":"harvest"}}],"adopt":{"from":"line","reason":"The line's figure, read on the five-slot with a check on the fit; this length's two photos, each through a camera fitted to its own teeth, bracket it (0.20 and 0.27) within their ±."},"note":"The line's figure, with the reason in its source."},"width":{"label":"Width (side to side, at its widest)","kind":"length","measurements":[{"id":"std","value":0.835,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.picatinny.top_width}","via":"harvest"},"note":"The head's widest is the standard's: Magpul, \"various 1913 Picatinny spec rail-mounted accessories\"."}]},"neck_width":{"label":"Width of the base's flat face (the body's foot, on the hand guard's face)","kind":"length","measurements":[{"id":"underside","value":0.6,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-9-slot 15d191b26285 (Primary Arms, MAG583_02.jpg: its underside, square on)","scaleRef":"its through holes eight standard pitches apart, in the base's plane: 496.6 px to the inch","method":"the base's flat face between the two lit creases along its length (rows 576 and 875 at column 1180, 581 and 880 at 1990, 570 and 868 at 220: 298 to 299 px), the teeth's widest standing out past them to the silhouette (0.81 to 0.83 in). Which way the faces outside the creases lean isn't read; drawn as the head's lower faces carried on at 45 degrees","via":"harvest"}}],"note":"The section under the head: the head's lower 45 degree faces carried on past the lower gauge line until they are this wide (0.228 in under the rail's top), and upright from there to the base, as the clamps' hooks need room under the head (rail-sections.test.ts) and as the photos of the underside show the base: narrower than the head by 0.11 in each side. Until 2026-10-29 the body was drawn upright at the lower gauge line's width (.748), an assumption, and three clamps' hooks stood in it. Midwest Gun Works' photos from above show a dark band 30 px deep under the head's widest on the near side, which a body undercut so far shows only as its shadow on the white ground: said in height's note."},"rail_slots":{"label":"Rail slots","kind":"count","measurements":[{"id":"name","value":9,"unit":"count","stated":"M-LOK® Aluminum Rail, 9 Slots","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, M-LOK® Aluminum Rail, 9 Slots (MAG583)","url":"https://magpul.com/m-lokaluminumrail-9slots.html","retrieved":"2026-10-29","via":"harvest"}}],"note":"Magpul's name for it; counted on its studio photo (9 grooves, 8 teeth between them and an end block at each end)."},"rail_slot0_x":{"label":"Rear rail slot's centre ahead of the part's rear end","kind":"length","measurements":[{"id":"pa-underside","value":0.395,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-9-slot 15d191b26285 (Primary Arms, MAG583_02.jpg, 2200 x 1467: its underside, square on)","scaleRef":"its three through holes (circles fitted to their white: 315.9, 1096.2 and 1881.2 px), the first and last eight standard pitches apart, at the base's own plane: 496.6 px to the inch","method":"the base's tip (120 px) to the first hole's centre: 0.3945 in","via":"harvest"}},{"id":"pa-plan","value":0.399,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-9-slot a2581c8858ef (Primary Arms, MAG583_01.jpg, 2200 x 1467: from above, square on, no screws)","scaleRef":"its first and last through holes (321.8 and 1877.6 px), eight pitches apart at the base's plane: 493.6 px to the inch","method":"the base's tip (125 px) to the first hole's centre: 0.3987 in","via":"harvest"}},{"id":"magpul-oblique","value":0.405,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-9-slot fa100863a0cc (Magpul's studio photo, from high over one end)","scaleRef":"its first and last through holes eight standard pitches apart, at the base's plane","method":"the base's tip to the near hole along the line through the holes","via":"harvest"}}],"adopt":{"from":"pa-underside","reason":"The base's own plane, square on and nearest the lens, at the scale of the holes in it; Primary Arms' view from above and Magpul's steep photo agree within their ±."}},"front_block":{"label":"Front end block: the last rail slot's centre to the part's front end","kind":"length","measurements":[{"id":"pa-underside","value":0.396,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-9-slot 15d191b26285 (Primary Arms, its underside)","scaleRef":"as for rail_slot0_x","method":"the last hole's centre to the base's tip (2078 px): 0.3963 in","via":"harvest"}},{"id":"pa-plan","value":0.398,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-9-slot a2581c8858ef (Primary Arms, from above)","scaleRef":"as for rail_slot0_x","method":"the last hole's centre to the base's tip (2074 px): 0.3979 in","via":"harvest"}}],"adopt":{"from":"pa-underside","reason":"As for rail_slot0_x."},"note":"Within its ± of the rear one: the part is the same both ways round."},"end_bevel_run":{"label":"The end bevel's run: from the base's tip in to the bevel's top edge (along the part)","kind":"length","measurements":[{"id":"line","value":0.131,"unit":"in","pm":0.025,"source":{"type":"derived","expr":"({magpul-mlok-aluminum-rail-section-3-slot.end_bevel_run} + {magpul-mlok-aluminum-rail-section-5-slot.end_bevel_run}) / 2","basis":"The line's end, read square from above on the three- and five-slot lengths (0.14 and 0.122 in): Magpul's sheet gives all four \"beveled ends\", and this length's studio photo shows the same arch and bevel, but at a slant that doesn't separate the bevel's top edge from the flat.","via":"harvest"}}]},"screw_count":{"label":"Screws (and T-nuts) it is held by","kind":"count","measurements":[{"id":"mgw","value":3,"unit":"count","stated":"Included with this premium piece is 3 cammed T-nuts and 3 recoil/impact mitigation lugs","source":{"type":"spec","publisher":"retailer","name":"Midwest Gun Works, Magpul Aluminum M-LOK Rail Section, 9 Slots (MAG583)","url":"https://www.midwestgunworks.com/page/mgwi/prod/mag583","retrieved":"2026-10-29","via":"harvest"}},{"id":"photo","value":3,"unit":"count","source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-9-slot b0cdaba292bd, fa100863a0cc and 4544d18032d6","scaleRef":"none: a count","method":"three T-nuts and three screws beside it in Midwest Gun Works' photo; three counterbores in Magpul's; three screws in it on a hand guard","via":"harvest"}}],"adopt":{"from":"mgw","reason":"The seller's sentence, counted on three photos."}},"screw_step":{"label":"Rail pitches from one screw to the next","kind":"count","measurements":[{"id":"photo","value":4,"unit":"count","source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-9-slot fa100863a0cc","scaleRef":"its grooves, counted","method":"its through holes stand in the first, fifth, ninth grooves' floors: 4 pitches apart","via":"harvest"}}],"note":"The first screw stands in the first groove's floor (rail_slot0_x)."},"lugs":{"label":"M-LOK slots its T-nuts span","kind":"count","measurements":[{"id":"derived","value":3,"unit":"count","source":{"type":"derived","expr":"{.screw_count}","basis":"Three T-nuts (Midwest Gun Works) on three screws one M-LOK slot pitch apart (screw_step: four rail pitches, 40 mm): one in each of three slots side by side. Magpul's photo of it on a hand guard (4544d18032d6) has each screw over a slot of the face's rows.","via":"harvest"}}]},"lug_x":{"label":"Its seat on the M-LOK face: the centre of the M-LOK slot its rear T-nut is in, ahead of its rear end","kind":"length","measurements":[{"id":"rear-nut","value":0.789,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{.rail_slot0_x} + {std.mlok.interval} / 2","basis":"The rear T-nut is on the rear screw, which stands on the first groove's centre (screw_step); the nut sits in the rear half of its M-LOK slot, half the M-LOK interval behind the slot's centre (the category's seat, data/categories/rail_section.yaml, as the polymer sections have it): what an M-LOK position places is that slot's centre.","via":"harvest"}}],"note":"Its three T-nuts are one M-LOK slot pitch apart (the screws over the first, fifth and ninth grooves): each in the rear half of its slot. Magpul's photos of it on a hand guard's side face (4544d18032d6, 1565ec2733f0) have its screws over the face's slots' centres, half an interval ahead of this seat: which half a nut is in isn't published, and the app's places, half a slot apart, are the same either way."},"reach_inside":{"label":"Reach inside the handguard (below the mounting face, tightened)","kind":"length","measurements":[],"note":"Not published: Magpul's M-LOK tips sheet sets the nut's top level with the recoil lug's bottom edge and gives neither's size."},"counterbore_d":{"label":"The screws' counterbores, across","kind":"length","measurements":[{"id":"pa-plan","value":0.37,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-mlok-aluminum-rail-section-9-slot a2581c8858ef (Primary Arms, from above)","scaleRef":"its holes' scale at the base (493.6 px/in) brought to the rail's top as the seven-slot's photo from the same seller has it (1.8% larger): about 502 px to the inch","method":"column 322 across the rear counterbore: its dark ring from 640 to 826 px (186 px), the through hole's white inside it","via":"harvest"}}]},"screw_head_d":{"label":"The screws' button heads, across","kind":"length","measurements":[{"id":"line","value":0.205,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"({magpul-mlok-aluminum-rail-section-3-slot.screw_head_d} + {magpul-mlok-aluminum-rail-section-5-slot.screw_head_d}) / 2","basis":"Magpul's M-LOK screws, as read in the three- and five-slot lengths' counterbores from above (0.20 and 0.21 in).","via":"harvest"}}]},"screw_seat_below_top":{"label":"How far below the rail's top the screws' heads seat (the counterbore's floor)","kind":"length","measurements":[{"id":"assumed","value":0.2,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows the counterbore's floor in profile. The heads are down in the counterbores below the grooves' floors in every photo with the screws in; their seat is put 0.04 in above the base.","via":"harvest"}}]},"screw_head_height":{"label":"The screws' button heads, high","kind":"length","measurements":[{"id":"assumed","value":0.08,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no camera is fitted to a photo of its screws from the side; a button head about a third as high as it is wide.","via":"harvest"}}]},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"metal","value":0.71,"unit":"oz","pm":0.15,"source":{"type":"derived","basis":"The rail's own aluminium: the model's volume, 0.4509 cubic inches (pipeline/blender/magpul_mlok_aluminum_rail_section.py's manifest for this length, app/public/models/magpul-mlok-aluminum-rail-section-9-slot.json volume_in3, the screws apart), times std.density.aluminium (1.568 oz to the cubic inch: the alloy isn't stated, \"Machined from milspec-anodized aluminum\"): 0.707 oz. The ± is the height's (± 0.03 in over its length and the width under its head) and the alloy's 4%.","via":"harvest"}}],"note":"Worked out, not weighed: no page on file gives its weight. The three screws and three T-nuts it is sold with are steel and not in it (no figure for them), nor the recoil lugs under the base, which aren't drawn."}}},{"subject":"magpul-mlok-hand-stop-moe-adapter","title":"Magpul M-LOK Hand Stop MOE Adapter (of the M-LOK Hand Stop Kit, MAG608)","dimensions":{"length":{"label":"Overall length (along the handguard)","kind":"length","measurements":[{"id":"plan","value":4.715,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop-moe-adapter c88ad5d113e3 (Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom)","scaleRef":"the plate's own four screw holes (the white seen through each, by intensity-weighted centroid: columns 419.19, 697.39, 1531.89, 1814.57) as 0, 20, 80 and 100 mm (std.mlok.interval, std.mlok.slot_pitch): a 1D projective map along the plate through the four by least squares, which leaves 1.0 px at each (13.83 px/mm at the rear pair, 14.05 at the front: the photo's perspective)","method":"the plate's two ends at mid-level 150 on the land either side of each end's notch (columns 285.3 and 280.5 at the left, 1951.4 and 1954.0 at the right), mapped: 119.76 mm. ± covers the holes' own miss (the pairs' middles read 3.976 intervals apart here, not 4: 0.6%), the lens and the edge","via":"harvest"}},{"id":"magpul-oblique","value":4.69,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop-moe-adapter 251db988739f (Magpul, the kit's page, gallery _01 (black), 1200 x 1200: the plate alone beside the kit's row, from above and one end)","scaleRef":"the plate's four holes in this photo at 0, 20, 80 and 100 mm, through a pinhole camera fitted to the plate (f 3221 px, 19.1 in away, 42.4 degrees above the land; residuals 0.4 to 0.8 px on the edges, 1.7 px on the holes)","method":"the land's two ends through that camera (4.656 in apart: the near one where the land gives way to the end face, the far one against the background) and the near end face's foot 0.017 in further out, taken the same at the far end","via":"harvest"}},{"id":"wing-oblique","value":4.697,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop-moe-adapter f82ccb133718 (Wing Tactical, the ODG kit with its hardware, 1280 x 1280: the plate outer side up, from above and the other end)","scaleRef":"the plate's four holes in this photo at 0, 20, 80 and 100 mm, through a pinhole camera fitted to the plate (f 2699 px, 15.2 in away, 45.6 degrees above the land; residuals 0.3 to 0.7 px on the edges, 1.1 px on the holes)","method":"the land's two ends through that camera (4.674 in apart) and the near end face's foot 0.012 in further out, taken the same at the far end","via":"harvest"}}],"adopt":{"from":"plan","reason":"The view from above, where the outline is the plate's foot at both ends. The two oblique photos, each scaled by its own holes through its own camera, read 0.4 and 0.5% less; the land between its ends reads 4.669, 4.656 and 4.674 in the three."},"note":"Three M-LOK slot pitches (120 mm, 4.724 in) within every reading's ±: the plate is as long as the kit's three pieces in a row, which a retailer's staff put at \"approximately 4.75 inches\" (OpticsPlanet's Q&A, quoted in the hand stop's seed)."},"height":{"label":"Thickness under what it carries (how far it stands them off the handguard's face)","kind":"length","measurements":[{"id":"magpul-oblique","value":0.103,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop-moe-adapter 251db988739f (Magpul, the kit's page, gallery _01 (black), 1200 x 1200: the plate alone beside the kit's row, from above and one end)","scaleRef":"the camera fitted to the plate in this photo (its four holes at 0, 20, 80, 100 mm; the land 0.656 in wide and the plate 0.900 as the photo from above has them; f 3221 px, 42.4 degrees above the land)","method":"the plate's near outline (its foot) below the land's near edge along each end section, 31 px down the columns against 93 px of land: through the camera, the foot 0.1025 in below the land (0.082 of it the bevel's drop, by the far side's band between the land and the far outline). The same within 0.001 with the principal point moved 100 px any way; 0.111 and 0.094 with the bevel 0.008 in narrower or wider in plan","via":"harvest"}},{"id":"wing-oblique","value":0.096,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop-moe-adapter f82ccb133718 (Wing Tactical, the ODG kit with its hardware, 1280 x 1280: the plate outer side up, from above and the other end)","scaleRef":"the camera fitted to the plate in this photo (f 2699 px, 45.6 degrees above the land)","method":"the same edges, the other specimen from the other end: the foot 0.0963 in below the land. Its lit end face, nearest the lens, is 9.5 to 10 px long past the land's end where 0.10 in of height and its 0.02 in run make 9.3","via":"harvest"}}],"adopt":{"from":"magpul-oblique","reason":"The larger photo, its edges the sharper (a black part on a pale ground); the two agree within 0.007 in."},"note":"The land's top above the end sections' underside: what the band between a hand stop's ears bears on, and the plate's whole thickness there. It is within its ± of that band's own depth (0.116 in on the hand stop's patent, 0.111 on the index panel's): the plate fills the space under the band, between the ears, that a flat face leaves empty. Magpul's drawing of the kit on the plate (072-0098-A, from the side and 15 degrees below) has the index panel's crown 0.238 to 0.245 in above the plate's underside, which is the panel's own height from its ears' tips (0.245 on its patent): there its ears' tips are level with the plate's underside. Read through fitted cameras from two photos, two specimens; not from a view square to the plate's side, of which there is none."},"width":{"label":"Width (side to side, at its widest: the moulded cover)","kind":"length","measurements":[{"id":"plan","value":1.036,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop-moe-adapter c88ad5d113e3 (Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom)","scaleRef":"the plate's own four holes along it (length); across, the same scale at each station's depth (the square root of the along-scale's change: the end sections read one width at both ends by it, 0.8931 and 0.8934) over 0.992, the plate lying rolled a few degrees in the photo (its holes read 1.2% narrower across than along, its far bevel 41.5 px against the near one's 44)","method":"the cover's outline across at 15 columns (363.6 px, sd 0.002 in). ± covers the roll (0.985 to 1.0) and the edge","via":"harvest"}}],"note":"The moulded cover between the two places. The index panel's plate is 1.038 in wide on its patent and the Type 2 cover 1.039: Magpul's image of the kit on the plate has their sides in one line. One photo: the two oblique photos fit these widths (their four long edges within 0.7 px) and cannot fix one themselves."},"end_width":{"label":"Width of the end sections (side to side, at the mounting face)","kind":"length","measurements":[{"id":"plan","value":0.9,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop-moe-adapter c88ad5d113e3 (Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom)","scaleRef":"as for width","method":"the end sections' outline across at 16 columns each (315.0 and 317.7 px: 0.8931 and 0.8934 in at each end's own scale), over 0.992","via":"harvest"}}],"note":"Narrower than what it carries (1.04 to 1.05 in): a hand stop's ears overhang it by 0.07 in a side."},"land_width":{"label":"Width of the flat on each end section (what an accessory's band bears on)","kind":"length","measurements":[{"id":"plan","value":0.656,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop-moe-adapter c88ad5d113e3 (Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom)","scaleRef":"as for width","method":"the two tone edges inside the outline along each end section (the land against the bevel either side of it: rows 1021.5 and 1252.5 at column 560, 1029.5 and 1259.5 at column 1670): 231 and 230 px","via":"harvest"}}],"note":"Each end section is a flat with a bevel down either side to the plate's edge. The flat is narrower than the band between a hand stop's ears (0.698 in on its patent; the index panel's 0.684): it lies between the ears, and the bevels (0.122 in across, falling 0.08 to 0.10: 35 degrees) run down under the ears' sloping insides (0.158 across, 0.116: 36 degrees)."},"edge_height":{"label":"Height of the end sections' edge (the bevel's foot above the mounting face)","kind":"length","measurements":[{"id":"magpul-oblique","value":0.021,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop-moe-adapter 251db988739f (Magpul, the kit's page, gallery _01 (black), 1200 x 1200: the plate alone beside the kit's row, from above and one end)","scaleRef":"the camera fitted to the plate in this photo (height)","method":"the far side's band (the far outline to the land's far edge, 6.2 and 5.0 px) gives the bevel's drop, 0.082 in; the near side's whole face gives 0.1025: the difference. A lighter strip 4 to 7 px high runs along the foot of the near face","via":"harvest"}},{"id":"wing-oblique","value":0,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop-moe-adapter f82ccb133718 (Wing Tactical, the ODG kit with its hardware, 1280 x 1280: the plate outer side up, from above and the other end)","scaleRef":"the camera fitted to the plate in this photo (height)","method":"the same difference: the bevel's drop 0.098 in of 0.096","via":"harvest"}}],"adopt":{"from":"magpul-oblique","reason":"The photo in which the strip along the foot shows; the other, half its size on the part, has the bevel run to the outline. Both say the edge is thin."}},"end_inset":{"label":"Land's end behind the plate's end (the end faces lean)","kind":"length","measurements":[{"id":"plan","value":0.023,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop-moe-adapter c88ad5d113e3 (Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom)","scaleRef":"the plate's own four holes (length)","method":"the lighter ramp at each end of the outline, about 8 px, before the land's own tone","via":"harvest"}},{"id":"magpul-oblique","value":0.017,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop-moe-adapter 251db988739f (Magpul, the kit's page, gallery _01 (black), 1200 x 1200: the plate alone beside the kit's row, from above and one end)","scaleRef":"the camera fitted to the plate in this photo (height)","method":"the near end face's foot beyond the land's end, along the plate","via":"harvest"}},{"id":"wing-oblique","value":0.012,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop-moe-adapter f82ccb133718 (Wing Tactical, the ODG kit with its hardware, 1280 x 1280: the plate outer side up, from above and the other end)","scaleRef":"the camera fitted to the plate in this photo (height)","method":"the near end face's foot beyond the land's end, along the plate","via":"harvest"}}],"adopt":{"from":"plan","reason":"Seen from above, where the lean is the whole of what shows at each end; the other two are a pixel or two each."}},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"wing","value":0.3,"unit":"oz","pm":0.05,"stated":"Weight: Handstop : 0.6 oz. Index Panel : 0.3 oz. Rail Cover : 0.15 oz. MOE Adapter : 0.3 oz.","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Magpul M-LOK Handstop Kit (MAG-608), Specifications (source of the figures unstated)","url":"https://www.wingtactical.com/firearm-parts/ar-15/handguards-rails/rail-system-parts-accessories/magpul-m-lok-handstop-kit/","retrieved":"2026-10-05","via":"harvest"}}],"note":"A retailer's per-piece list for the kit, its source unstated (the hand stop 0.6 oz, the index panel 0.3 oz, the rail cover 0.15 oz). Magpul states no weight."},"lugs":{"label":"M-LOK slots it covers","kind":"count","measurements":[{"id":"plan","value":3,"unit":"count","source":{"type":"photo","photo":"references/magpul-mlok-hand-stop-moe-adapter c88ad5d113e3 (Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom)","scaleRef":"the plate's own four holes (length)","method":"119.8 mm of plate at the 40 mm slot pitch, its two places 19.9 mm from either end and two pitches apart: a place over the first slot it covers and one over the third, the moulded cover over the one between. Magpul's sheet draws it so on a Magpul hand guard (scenario 2, step 2: the stop's two T-nuts into one slot, the panel's into the next but one)","via":"harvest"}}]},"positions":{"label":"Places it has for what it carries","kind":"count","measurements":[{"id":"sheet","value":2,"unit":"count","stated":"Attach the M-LOK Hand Stop and Index Panel to the M-LOK Hand Stop MOE Adapter and insert the Screws through the bottom of the M-LOK Hand Stop and Index Panel.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MAG608 M-LOK Hand Stop Kit installation instructions (072-0098-A), scenario 2, step 1","url":"https://magpul.com/media/wysiwyg/Instructions/MAG608_M-LOK_Hand_Stop_Kit_INSRT.pdf","retrieved":"2026-10-05","via":"harvest"}}],"note":"One at each end, each a recess the shape of an M-LOK slot with two screw holes in its floor; the middle is a moulded cover (\"The M-LOK Hand Stop MOE Adapter plate has an integral rail cover therefore the Type 2 Rail Cover is not used\")."},"position_pitch":{"label":"Distance between those places","kind":"length","measurements":[{"id":"sheet","value":3.149,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop-moe-adapter docs/ab899abe59.pdf (Magpul, MAG608 installation instructions 072-0098-A, scenario 2 step 2: the kit on the plate over a Magpul hand guard, from the side and a little below; vector art, rendered at 4800 dpi)","scaleRef":"the plate's own pairs of screw holes in the drawing, by the seats that stand either side of each (matched pair to pair by correlation: 783.85 px at both ends, so the view is parallel), as the M-LOK interval (std.mlok.interval)","method":"the pairs' middles 3134.5 px apart: 3.9988 intervals","via":"harvest"}},{"id":"magpul-oblique","value":3.142,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop-moe-adapter 251db988739f (Magpul, the kit's page, gallery _01 (black), 1200 x 1200: the plate alone beside the kit's row, from above and one end)","scaleRef":"the pairs' own spacing as the M-LOK interval, whatever the camera: the cross-ratio of the four holes' centres along their line (the white seen through each; on one line within 0.15 px)","method":"cross-ratio 1.06700: the pairs' middles 3.9906 intervals apart. 0.3 px on one centre moves it 0.006 intervals","via":"harvest"}},{"id":"wing-oblique","value":3.14,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop-moe-adapter f82ccb133718 (Wing Tactical, the ODG kit with its hardware, 1280 x 1280: the plate outer side up, from above and the other end)","scaleRef":"the cross-ratio of the four holes' centres, as above (the inner two 1.7 px off the outer two's line)","method":"cross-ratio 1.06711: 3.9875 intervals","via":"harvest"}},{"id":"plan","value":3.131,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop-moe-adapter c88ad5d113e3 (Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom)","scaleRef":"the cross-ratio of the four holes' centres, as above","method":"cross-ratio 1.06754: 3.9758 intervals. The holes' line is bowed 0.5 px the way a lens that stretches toward the frame's edge bows it, which reads this ratio low; the ± is for that, not for the centres (0.1 px)","via":"harvest"}}],"adopt":{"from":"sheet","reason":"Magpul's own drawing of the plate, made from its model and parallel: four intervals, which is two slot pitches (std.mlok.slot_pitch, 3.150 in), as the places must be to stand over the first and third of three slots. The three photos read 0.2 to 0.6% less, each with its own cause for it: a cross-ratio, which no lens keeps."},"note":"Two M-LOK slot pitches: each place stands over a slot's centre, with one slot between."},"position_x":{"label":"Rear place's centre ahead of the plate's rear end","kind":"length","measurements":[{"id":"plan","value":0.783,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop-moe-adapter c88ad5d113e3 (Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom)","scaleRef":"the plate's own four holes (length)","method":"the middle of each pair of holes from its own end of the plate: 19.93 mm at one end, 19.84 at the other","via":"harvest"}},{"id":"magpul-oblique","value":0.769,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop-moe-adapter 251db988739f (Magpul, the kit's page, gallery _01 (black), 1200 x 1200: the plate alone beside the kit's row, from above and one end)","scaleRef":"the camera fitted to the plate in this photo (length)","method":"the near pair's middle from the near end's foot","via":"harvest"}},{"id":"wing-oblique","value":0.776,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop-moe-adapter f82ccb133718 (Wing Tactical, the ODG kit with its hardware, 1280 x 1280: the plate outer side up, from above and the other end)","scaleRef":"the camera fitted to the plate in this photo (length)","method":"the near pair's middle from the near end's foot","via":"harvest"}}],"adopt":{"from":"plan","reason":"The view from above, with both ends in it: the two ends read the same within 0.004 in, so the plate is the same end for end. The oblique photos read 0.007 and 0.014 less, as they read the length."},"note":"Half a slot pitch (0.787 in) within the ±: the plate's end is where the first slot's pitch begins. The same from either end: there is no front or rear to it but its lettering."},"reach_inside":{"label":"Reach inside the handguard (below the mounting face)","kind":"length","measurements":[],"note":"Not measured. Either side of each screw hole a crescent seat stands off the mounting side, fore and aft (Wing Tactical's photo of the FDE kit from its mounting sides; Magpul's drawings): they stand in the hand guard's slot, as a hand stop's own do. The screws and T-nuts are the carried accessories'."},"carried_reach_inside":{"label":"Room under an accessory it carries (for its screws and T-nut)","kind":"length","measurements":[],"note":"No figure from Magpul. Each place's recess is 0.07 in deep in a 0.10 in plate (recess_depth): what stands off an accessory's band into a slot goes into it, and its screws go on through the floor into the hand guard's own slot."},"score_x":{"label":"Snap-off score's centre ahead of the plate's end (each end section's length)","kind":"length","measurements":[{"id":"plan","value":1.552,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop-moe-adapter c88ad5d113e3 (Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom)","scaleRef":"the plate's own four holes (length)","method":"the dark line across the plate between each end section and the cover (columns 826 to 833 and 1394 to 1402 on rows either side of the recess): its middle 39.53 mm from one end and 39.34 from the other","via":"harvest"}}],"note":"\"The M-LOK Hand Stop MOE Adapter plate is customizable to length by snapping off sections at the marked locations\" (072-0098-A): the two lines, one at each end of the cover. Each end section is as long as the hand stop's plate or the index panel's (1.56 to 1.575 in): an accessory covers it to the score."},"score_width":{"label":"Snap-off score's width","kind":"length","measurements":[{"id":"plan","value":0.02,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop-moe-adapter c88ad5d113e3 (Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom)","scaleRef":"the plate's own four holes (length)","method":"the dark line's width, 7 px at both","via":"harvest"}}]},"cover_height":{"label":"Moulded cover's crown above the mounting face","kind":"length","measurements":[{"id":"sheet","value":0.24,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop-moe-adapter docs/ab899abe59.pdf (Magpul, MAG608 installation instructions 072-0098-A, scenario 2 step 2: the kit on the plate over a Magpul hand guard, from the side and a little below; vector art, rendered at 4800 dpi)","scaleRef":"the plate's own pairs of holes in the drawing as the M-LOK interval (995.5 px/in along it); the view 15 degrees below level, by the plate's underside (0.900 in wide: 232 px between its near and far edges)","method":"the cover's top line and the index panel's are one line within 2 px (rows 452 to 468 and 451 to 466): flush. The panel's upper outline is 280 px above the middle of the plate's underside: its crown 0.238 in above it, for the 0.245 in its patent gives from its ears' tips. ± covers the line's width and the angle","via":"harvest"}}],"note":"Flush with what it stands between: Magpul's image of the kit on the plate shows one surface from the hand stop over the cover to the index panel. In the two oblique photos this crown, with the two heights below, is within 3 px of the cover's outline through each fitted camera at the near side and within 8 at the far."},"cover_shoulder_height":{"label":"Moulded cover's height above the mounting face over the land's edge","kind":"length","measurements":[{"id":"sheet","value":0.203,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop-moe-adapter docs/ab899abe59.pdf (Magpul, MAG608 installation instructions 072-0098-A, scenario 2 step 2: the kit on the plate over a Magpul hand guard, from the side and a little below; vector art, rendered at 4800 dpi)","scaleRef":"as for cover_height","method":"seen from 15 degrees below, the cover's upper outline is its near shoulder, not its crown: 0.966 y + 0.259 z = 0.281 in at the point the view touches, which at z = half the land's width is this height. The index panel's plate, drawn flush with it, is 0.21 there on its patent","via":"harvest"}}]},"cover_edge_height":{"label":"Moulded cover's height above the mounting face over the end sections' edge","kind":"length","measurements":[{"id":"magpul-oblique","value":0.12,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop-moe-adapter 251db988739f (Magpul, the kit's page, gallery _01 (black), 1200 x 1200: the plate alone beside the kit's row, from above and one end)","scaleRef":"the camera fitted to the plate in this photo (height)","method":"the cover's far outline, 1 to 3 px above where a wing tip 0.046 in high at z = 0.513 would put it: 0.738 y + 0.674 z = 0.392 in where the view touches the far side, which at z = half the end sections' width is this height. Its near outline, 9 px below the end sections' own, is the wing tips at the mounting face's level (within 0.015 in) at the cover's full width; Wing Tactical's photo reads the same 9 px","via":"harvest"}}],"note":"Over the plate's edge the cover is still above the land; from there it turns down to its own edge at the mounting face's level, 0.068 in further out."},"cover_end_lean":{"label":"Moulded cover's end faces: how far they lean back from the land's level to the crown","kind":"length","measurements":[{"id":"magpul-oblique","value":0.052,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop-moe-adapter 251db988739f (Magpul, the kit's page, gallery _01 (black), 1200 x 1200: the plate alone beside the kit's row, from above and one end)","scaleRef":"the camera fitted to the plate in this photo (height): 165 px/in along the plate there, and 52.5 px along it for each inch of height","method":"the dark band across the plate where the land meets the cover's near end (the score and the end face, in shade), on lines along the plate over the land's far half: 19 px. The score's 0.020 in and the crown's height above the land (cover_height less height) account for 10.5 of them; the rest is the face's lean","via":"harvest"}},{"id":"wing-oblique","value":0.042,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop-moe-adapter f82ccb133718 (Wing Tactical, the ODG kit with its hardware, 1280 x 1280: the plate outer side up, from above and the other end)","scaleRef":"the camera fitted to the plate in this photo (height): 174 px/in along the plate there, 56.5 px per inch of height","method":"the same band at the cover's other end, 18.5 px, of which the score and the crown's height account for 11.2","via":"harvest"}}],"adopt":{"from":"magpul-oblique","reason":"The larger photo. Both rest on the crown's height, which is the drawing's; they are one reading of the lean from each end of the cover."},"note":"Magpul's drawing of the kit from the side shows the cover's ends sloped too. With it the cover's top stands clear of an accessory's end where its foot does not."},"cover_corner_radius":{"label":"Moulded cover's corner radius in plan","kind":"length","measurements":[{"id":"plan","value":0.11,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop-moe-adapter c88ad5d113e3 (Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom)","scaleRef":"the plate's own four holes (length)","method":"the outline's step from the end sections' width to the cover's, an arc over 39 px along the plate at each of its four corners","via":"harvest"}}]},"cover_underside_drop":{"label":"Moulded cover's ribbed underside below the end sections' mounting face","kind":"length","measurements":[],"note":"Not measured. Under the cover the plate is a waffle of ribs (Wing Tactical's photo of its mounting side), and three sources have its rim standing below the end sections' underside: that photo (a step where an end section meets it), Magpul's drawing from the side (the lower outline bulges under the cover, about 0.03 in) and Magpul's low side view of the plate (references/magpul-mlok-hand-stop 09443d72a495: the cover's lower edge 15 to 20 px below the end sections', where the two photos from 42 and 46 degrees have its wing tips level with them: something inboard of the tips, hidden from above). None is through a fitted camera. On a flat face it would touch before the ends do."},"recess_length":{"label":"Recess at each place: length","kind":"length","measurements":[{"id":"plan","value":1.232,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop-moe-adapter c88ad5d113e3 (Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom)","scaleRef":"the plate's own four holes (length)","method":"the recess's two ends along the plate (columns 338 and 772 at the rear place, 1451 and 1892 at the front): 31.3 mm at both, centred on the pair of holes within 0.25 mm","via":"harvest"}}],"note":"An M-LOK slot's length (std.mlok.slot_length, 32 mm ± 1): each place is a slot's own shape cut into the land, for what stands off an accessory's band into a hand guard's slot."},"recess_width":{"label":"Recess at each place: width","kind":"length","measurements":[{"id":"plan","value":0.279,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop-moe-adapter c88ad5d113e3 (Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom)","scaleRef":"as for width","method":"the recess's two long edges (rows 1088 and 1184.5 to 1187 at the rear place): 98 px, 7.09 mm","via":"harvest"}}],"note":"An M-LOK slot's width (std.mlok.slot_width, 7 mm ± 0.5)."},"recess_depth":{"label":"Recess at each place: depth below the land","kind":"length","measurements":[{"id":"magpul-oblique","value":0.066,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop-moe-adapter 251db988739f (Magpul, the kit's page, gallery _01 (black), 1200 x 1200: the plate alone beside the kit's row, from above and one end)","scaleRef":"the camera fitted to the plate in this photo (height)","method":"the white seen through each hole is what its rim on the recess's floor and its rim on the mounting side leave between them, so its centre lies midway between the two levels: fitted 0.084 in below the land, with the mounting side 0.1025 below. Wing Tactical's photo fits 0.100, which is below its own plate: there the seats either side of each hole, in line with the lens, close the view, and the ± is for that","via":"harvest"}}]},"screw_hole_diameter":{"label":"Screw holes' diameter","kind":"length","measurements":[{"id":"plan","value":0.224,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop-moe-adapter c88ad5d113e3 (Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom)","scaleRef":"the plate's own four holes' spacing (length), at each pair's own scale","method":"each hole's width along the plate, by the second moment of the white seen through it: 78.5, 78.5, 79.9 and 80.7 px","via":"harvest"}}],"note":"The index panel's hole is 0.219 in on its patent: the kit's screws go through both."},"end_notch_depth":{"label":"Notch in each end: depth","kind":"length","measurements":[{"id":"plan","value":0.03,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop-moe-adapter c88ad5d113e3 (Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom)","scaleRef":"the plate's own four holes (length)","method":"the outline's step back in the middle of each end: 0.77 and 0.74 mm","via":"harvest"}}]},"end_notch_width":{"label":"Notch in each end: width","kind":"length","measurements":[{"id":"plan","value":0.3,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop-moe-adapter c88ad5d113e3 (Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom)","scaleRef":"as for width","method":"the rows the step holds over, 1080 to 1190 with a row or two of corner at each: in line with the recess, and a little wider","via":"harvest"}}]}}},{"subject":"magpul-mlok-hand-stop","title":"Magpul M-LOK Hand Stop (of the M-LOK Hand Stop Kit, MAG608)","dimensions":{"length":{"label":"Overall length (the base plate, along the handguard)","kind":"length","measurements":[{"id":"render","value":1.575,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop 0474c600d6a0 (Supplied in chat 2026-10-02: a gallery image of an M-LOK handguard, straight side view, the hand stop and the index panel installed, rail teeth along the top, 2796 x 1290)","scaleRef":"the handguard's rail teeth in the same image (calibrate.py rail: 16 slots, 132.58 px/slot, drift +0.04%, rms 0.002 in): 336.5 px/in","method":"the base plate's two ends: the hook's front wall (u 687 to 691, rows 800 to 950) and the gap before the next rail cover (u 1217 to 1221, rows 745 to 785): 530 px; ± 4 px","via":"user"}},{"id":"patent-screws","value":1.564,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop 322d06fd979a (US D755,333 S, Magpul, FIG. 8 bottom plan; the patent office's copy, page 10, 300 dpi)","scaleRef":"the two screw holes' centres, 1026 px apart, taken as the M-LOK interval (std.mlok.interval, 20 mm: Magpul's FAQ)","method":"the plan view's length, 2038 px, over the holes' spacing; the centres by eye on a half-size crop, ± 6 px","via":"harvest"}}],"adopt":{"from":"render","reason":"Measured on an image of the product, in the plane of its scale. The patent's plan view, scaled by its own screw holes, agrees within 0.011 in. Both are 40 mm, the M-LOK slot pitch, within their ±."},"note":"The plate covers one slot pitch. A retailer's staff and a customer put the kit's three pieces together at about 4.75 in (OpticsPlanet, MidwayUSA; neither page on file): three of these. The first reading, 1.334, was the hook alone (the subject's header)."},"height":{"label":"Height (how far it stands off the handguard's face)","kind":"length","measurements":[{"id":"patent","value":1.505,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop f25270f81003 (US D755,333 S (Magpul, 'Hand stop for a firearm'), FIG. 6 right side elevation, 300 dpi)","scaleRef":"scale from magpul-mlok-hand-stop.length = 1.575 in (x-extent 1549 px → 983.5 px/in)","method":"height of the traced outline (tools/trace.py); the patent's side elevation scaled to the plate's length: the mounting face to the lip's lowest point","via":"harvest"}},{"id":"render","value":1.449,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop 0474c600d6a0 (Supplied in chat 2026-10-02: a gallery image of an M-LOK handguard, straight side view, the hand stop and the index panel installed, rail teeth along the top, 2796 x 1290)","scaleRef":"the handguard's rail teeth in the same image (calibrate.py rail: 16 slots, 132.58 px/slot, drift +0.04%, rms 0.002 in): 336.5 px/in","method":"the plate's top edge (row 714, where its rounded ends begin either side of the hook) to the lip's lowest point (row 1201.5): 487.5 px; ± 3 px at each. Until 2026-10-05 this was read from row 688.5 and stood at 1.524: the band from there down to row 712 runs on unbroken past both ends of the plate and over the covers beside it, so it is the handguard's and not the plate's (seen on a contrast-stretched crop of that band while the index panel was measured on the same image)","via":"user"}}],"adopt":{"from":"patent","reason":"Line art, whole and orthographic, and what the outline is traced from. The image has the stop 0.056 in less from its plate's top edge to its lip, and the plate 0.208 in thick where the patent's outermost line on that side gives 0.246: the ears' tips look that much lower on the part as made than the patent's outermost line (the index panel's plate, the same plate, reads 0.213 in the same image). Nothing moves by it: the part is seated by the band between its ears, which the hook is measured from the same in both."},"note":"The ears' tips to the lip's lowest point. The patent's side elevation, scaled to the plate's length, is the outline; the image is a second reading and disagrees by about a twentieth of an inch at the ears (2026-10-05: until then it was read from the handguard's own band and seemed to agree). Below the plate's outer surface the hook reads 1.230 in the image (row 788 down) and 1.255 in the patent."},"width":{"label":"Width (side to side)","kind":"length","measurements":[{"id":"patent","value":1.053,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop 322d06fd979a (US D755,333 S, Magpul, FIG. 8 bottom plan; the patent office's copy, page 10, 300 dpi)","scaleRef":"the plan view's own length, 2038 px, as the plate's length (.length, 1.575 in)","method":"the plan view's width, 1363 px, at the mounting face (the widest: the stop tapers to its lip). The front and rear elevations (FIG. 3, FIG. 4), drawn at the same scale, read 1361. ± covers the length's ± and a design patent's fidelity (the MOE+, MOE Carbine and MOE SL patents read within 0.6% of Magpul's figures; the K2+'s 13% over)","via":"harvest"}}],"note":"No published figure. From Magpul's design patent, scaled by the plate's length."},"weight":{"label":"Weight (the hand stop alone, as mounted)","kind":"mass","measurements":[{"id":"wing","value":0.6,"unit":"oz","pm":0.05,"stated":"Weight: Handstop : 0.6 oz. Index Panel : 0.3 oz. Rail Cover : 0.15 oz. MOE Adapter : 0.3 oz.","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Magpul M-LOK Handstop Kit (MAG-608), Specifications (source of the figures unstated)","url":"https://www.wingtactical.com/firearm-parts/ar-15/handguards-rails/rail-system-parts-accessories/magpul-m-lok-handstop-kit/","retrieved":"2026-10-02","via":"harvest"}}],"note":"The hand stop alone. The kit's index panel (0.3 oz) and rail cover (0.15 oz) are parts of their own since 2026-10-05 (D71), each with its figure from the same list; its adapter plate (0.3 oz) isn't drawn. A configurator site's \"approximately 1.2 ounces\" is the kit. Magpul states no weight."},"lugs":{"label":"M-LOK slots its lugs span","kind":"count","measurements":[{"id":"photo","value":1,"unit":"count","source":{"type":"photo","photo":"references/magpul-mlok-hand-stop 322d06fd979a (US D755,333 S, Magpul, FIG. 8 bottom plan; the patent office's copy, page 10, 300 dpi)","scaleRef":"the plan view's length as the plate's (.length)","method":"the two screw holes stand 0.79 in apart on a 1.575 in plate: one 32 mm slot takes both nuts, and the plate covers that slot's pitch","via":"harvest"}},{"id":"configurator","value":2,"unit":"count","stated":"The hand stop occupies two M-LOK slots, the index panel one slot, and the rail cover spans two.","source":{"type":"spec","publisher":"review","name":"rifleconfigurator.com, Magpul M-LOK Hand Stop Kit (a configurator site; source of the statement unstated)","url":"https://www.rifleconfigurator.com/catalog/controls/magpul-m-lok-hand-stop-kit","retrieved":"2026-10-02","via":"harvest"}}],"adopt":{"from":"photo","reason":"Two nuts a 20 mm interval apart sit in one slot, and a plate one pitch long covers one; the site's statement is unattributed and may count the kit's pieces together."},"note":"The base plate is one slot pitch long (40 mm) and its two screws a 20 mm interval apart (the patent's plan view): both T-nuts go into one slot, as the MVG's do. A configurator site says two slots, unattributed; Magpul's sheet names no count."},"reach_inside":{"label":"Reach inside the handguard (below the mounting face, tightened)","kind":"length","measurements":[],"note":"Not sourced (as for the MVG: Magpul publishes no T-nut figure)."},"mounting_band_depth":{"label":"Mounting face: the band between the ears, below the ears' tips","kind":"length","measurements":[{"id":"patent","value":0.116,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop 644316cf46e4 (US D755,333 S (Magpul, 'Hand stop for a firearm'), FIG. 3 front elevation, 300 dpi)","scaleRef":"the traced front elevation's own scale (profiles.front: magpul-mlok-hand-stop.height and .width, 1288.7 px/in)","method":"the flat between the ears on the traced outline, at y 0.116 from z -0.348 to +0.350, against the ears' tips at y 0 (z ±0.52)","via":"harvest"}}],"note":"The band is what bears on a handguard's M-LOK face (2026-10-05, the model review: seated on its ears' tips it touched nothing on the 22RB's bottom flat, 0.12 to 0.17 in of air everywhere). Its ears slope out and up from the band's edges, 0.17 in across and this high: they run down either side of a face narrower than the band, as every M-LOK face on file is. On a flat wider than the ears' tips (1.05 in) the tips would bear instead."},"mounting_band_width":{"label":"Mounting face: the band between the ears, across","kind":"length","measurements":[{"id":"patent","value":0.698,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop 644316cf46e4 (US D755,333 S (Magpul, 'Hand stop for a firearm'), FIG. 3 front elevation, 300 dpi)","scaleRef":"the traced front elevation's own scale (profiles.front, 1288.7 px/in)","method":"the flat between the ears on the traced outline: z -0.348 to +0.350","via":"harvest"}}]},"lug_x":{"label":"Rear lug's centre ahead of the part's rear end","kind":"length","measurements":[{"id":"patent","value":0.374,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop 322d06fd979a (US D755,333 S, Magpul, FIG. 8 bottom plan; the patent office's copy, page 10, 300 dpi)","scaleRef":"the plan view's own length, 2038 px, as the plate's length (.length, 1.575 in)","method":"the lip-end screw hole's centre, 484 px from the plate's lip end (the tail-end one is 528 px from the tail, the two 1026 px apart); by eye on a half-size crop, ± 6 px","via":"harvest"}}],"note":"From the patent's plan view: the screw at the hook's end, which is the part's rear (2026-10-05: the part's frame was turned end for end, its hook to the rear as Magpul pictures it; until then this was the tail-end screw, 0.408 from the tail). The tail-end screw is 0.408 in from the front end, and the two 0.793 apart (20.1 mm)."},"screw_hole_diameter":{"label":"Screw hole (through the plate)","kind":"length","measurements":[{"id":"patent-bottom","value":0.22,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop 322d06fd979a (US D755,333 S, Magpul, FIG. 8 bottom plan; the patent office's copy, page 10, 300 dpi)","scaleRef":"the plan view's own length, 2038 px, as the plate's length (.length, 1.575 in): 1294.0 px/in","method":"the innermost of the five broken-line circles round the plate's screw, fitted on one centre: radius 142.6 px (a second, 155.6 px, is drawn 13 px outside it). The index panel's hole is 0.219 in on its own drawing","via":"harvest"}}]},"screw_recess_diameter":{"label":"Screw's recess in the outer face, at its rim","kind":"length","measurements":[{"id":"patent-bottom","value":0.399,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop 322d06fd979a (US D755,333 S, Magpul, FIG. 8 bottom plan; the patent office's copy, page 10, 300 dpi)","scaleRef":"the plan view's own length, 2038 px, as the plate's length (.length, 1.575 in): 1294.0 px/in","method":"the outermost of the five broken-line circles, fitted: radius 257.9 px (the next in, 244.3 px, 0.378 in)","via":"harvest"}}],"note":"FIG. 8's outermost circle here; the index panel's own drawing has one more outside it (0.429 in). How deep the recess is no view gives."},"screw_recess_floor_diameter":{"label":"Screw's recess in the outer face, the innermost of its three circles","kind":"length","measurements":[{"id":"patent-bottom","value":0.358,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop 322d06fd979a (US D755,333 S, Magpul, FIG. 8 bottom plan; the patent office's copy, page 10, 300 dpi)","scaleRef":"the plan view's own length, 2038 px, as the plate's length (.length, 1.575 in): 1294.0 px/in","method":"the third circle out from the centre, fitted: radius 231.3 px. The index panel's is 0.360 in on its own drawing: the same dish for the same screw","via":"harvest"}}]},"screw_head_diameter":{"label":"Screw's head, across","kind":"length","measurements":[{"id":"gallery-fde","value":0.375,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop 343c6dde53f4 (Magpul's gallery for MAG608, mag608_fde_2.png, 1200 x 1200: the FDE kit's pieces put together with their screws in, three-quarter from the outer side)","scaleRef":"the recess's rim in the same view, as .screw_recess_diameter (0.399 in): both are circles on one axis a few hundredths of an inch apart in depth, so their long axes are in the ratio of their diameters","method":"the dark head's long axis 56.8 px (columns 652 to 710 at luminance under 75) against the rim's 60.5 px, read on a tenfold enlargement; ± covers a pixel and a half on each and the rim's soft edge","via":"harvest"}}],"note":"Magpul publishes no figure for the kit's screws. A wide low head with a six-lobe socket (Wing Tactical's photo of the kit's hardware: six alike). The index panel's, read the same way on the same picture, is 0.364 in."},"screw_head_proud":{"label":"Screw's head: its crown above the plate's outer face","kind":"length","measurements":[{"id":"render","value":0.033,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop 0474c600d6a0 (Supplied in chat 2026-10-02: a gallery image of an M-LOK handguard, straight side view, the hand stop and the index panel installed, rail teeth along the top, 2796 x 1290)","scaleRef":"the handguard's rail teeth in the same image: 336.5 px/in","method":"the plate's outer face at half tone on its smooth stretch behind the screw (rows 785.1 to 786.4, u 1136 to 1208) to the head's lowest point (row 796.8, u 1080 to 1096): 11.0 px; ± covers 2 px and the face's own 1.3 px","via":"user"}}],"note":"A rendering whose source page isn't on file (the ledger's header); the index panel's screw reads 0.034 in on the same image."}}},{"subject":"magpul-mlok-index-panel","title":"Magpul M-LOK Index Panel (of the M-LOK Hand Stop Kit, MAG608)","dimensions":{"length":{"label":"Overall length (the plate, along the handguard)","kind":"length","measurements":[{"id":"render","value":1.558,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-mlok-index-panel 0474c600d6a0 (Supplied in chat 2026-10-02: a gallery image of an M-LOK handguard, straight side view, the hand stop and the index panel installed, rail teeth along the top, 2796 x 1290)","scaleRef":"the handguard's rail teeth in the same image (calibrate.py rail: 16 slots, 132.58 px/slot, drift +0.04%, rms 0.002 in): 336.5 px/in. Checked in the plate's own plane: the seams between the pieces on the bottom face (u 1219, 1754, 2283) are 532 px apart, 40.2 mm on that scale for the 40 mm slot pitch (std.mlok.slot_pitch)","method":"the plate's two ends, each between the seam's darkest column (u 1754 and 2283, rows 725 to 770: 529 px) and where the tone is halfway back to the plate's own (u 1758.4 and 2278.2: 519.8 px): 524.4 px ± 4.6. Its rounded ends are in the seams' shadow","via":"user"}},{"id":"patent-bosses","value":1.559,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-mlok-index-panel 68be85d611cb (US D755,334 S, Magpul, FIG. 7 top plan: the mounting face, in broken lines; the patent office's copy, page 8, 300 dpi)","scaleRef":"the screw hole's centre (fitted circle, row 1178.6, rms 0.6 px) and the middle of the second pair of bosses (rows 1907 to 2516: 2211.2), 1032.6 px apart, taken as the M-LOK interval (std.mlok.interval, 20 mm: Magpul's FAQ), as the hand stop's two screws are","method":"the plan view's length, 2044 px (rows 673 to 2717), over that spacing; ± 8 px on the two centres","via":"harvest"}}],"adopt":{"from":"render","reason":"Measured on an image of the product, in the plane of its scale. The patent's top plan, scaled by its own bosses as one M-LOK interval, agrees within 0.001 in. Both are a little under 40 mm, the slot pitch the pieces stand at."},"note":"The plate covers one M-LOK slot pitch less the seams to its neighbours (39.6 mm read). The hand stop's plate reads 1.575 ± 0.012 in the same image, by one end and a seam's middle; the two are the same within their ±. A retailer's staff put each of the kit's panels at \"approximately 40 mm\" (OpticsPlanet's Q&A, quoted in the hand stop's seed; not harvested for this part)."},"height":{"label":"Height (how far it stands off the handguard's face)","kind":"length","measurements":[{"id":"patent","value":0.745,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-mlok-index-panel c190e3d7fbdd (US D755,334 S (Magpul, 'Index attachment for a firearm'), FIG. 5 left side elevation, 300 dpi)","scaleRef":"scale from magpul-mlok-index-panel.length = 1.558 in (x-extent 2159 px → 1385.8 px/in)","method":"height of the traced outline (tools/trace.py); the patent's side elevation scaled to the plate's length: the ears' tips (the outermost line on the mounting side, in broken strokes; the shading's ticks outside it left out) to the fin's tip. The front elevation, scaled by this and by the plan's width, fits both with one scale within 0.1%","via":"harvest"}},{"id":"render","value":0.704,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-mlok-index-panel 0474c600d6a0 (Supplied in chat 2026-10-02: a gallery image of an M-LOK handguard, straight side view, the hand stop and the index panel installed, rail teeth along the top, 2796 x 1290)","scaleRef":"the handguard's rail teeth in the same image: 336.5 px/in","method":"the plate's top edge where it shows (the dark line under the handguard's band, rows 710 to 715, down which the pieces' seams begin: row 714 ± 2) to the fin's lowest point (row 950.8): 236.8 px. The band above that line (rows 687 to 712, 0.075 in) runs unbroken across the seams and has dark openings in it: it is the handguard's lower face, not the plate","via":"user"}}],"adopt":{"from":"patent","reason":"Line art, whole and orthographic. In the image the plate's top is dark against the handguard, and what shows of it is 0.04 in less than the drawing's: all of the difference is in the plate (0.213 in showing against the drawing's 0.246; the fin below it agrees within 0.008, fin_height). Either the ears' last 0.03 in is hidden there or the drawing's broken outermost line stands that far off the part; the bearing band is placed from the drawing."},"note":"From the ears' tips (the outermost line on the mounting side) to the fin's tip. The band between the ears, which bears on a handguard, is mounting_band_depth nearer the tip."},"width":{"label":"Width (side to side)","kind":"length","measurements":[{"id":"patent","value":1.038,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-mlok-index-panel 0c155e219281 (US D755,334 S, Magpul, FIG. 8 bottom plan; the patent office's copy, page 9, 300 dpi)","scaleRef":"the plan view's own length, 1866 px (rows 786 to 2652), as the plate's length (.length, 1.558 in)","method":"the plan view's width, 1243 px (columns 638 to 1881), at the ears' tips (the widest: the plate's outer face is narrower). FIG. 7 reads the same ratio (1362 over 2044: 0.666). ± covers the length's ± and a design patent's fidelity","via":"harvest"}}],"note":"No published figure. From Magpul's design patent, scaled by the plate's length. The hand stop's, from its own patent the same way, is 1.053 (its plate read 1% longer): Magpul's photos show the kit's pieces in a row with their sides in line."},"weight":{"label":"Weight (the index panel alone, as mounted)","kind":"mass","measurements":[{"id":"wing","value":0.3,"unit":"oz","pm":0.05,"stated":"Weight: Handstop : 0.6 oz. Index Panel : 0.3 oz. Rail Cover : 0.15 oz. MOE Adapter : 0.3 oz.","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Magpul M-LOK Handstop Kit (MAG-608), Specifications (source of the figures unstated)","url":"https://www.wingtactical.com/firearm-parts/ar-15/handguards-rails/rail-system-parts-accessories/magpul-m-lok-handstop-kit/","retrieved":"2026-10-05","via":"harvest"}}],"note":"A retailer's per-piece list for the kit, its source unstated (the hand stop 0.6 oz, the rail cover 0.15 oz, the adapter plate 0.3 oz); whether its screw and T-nut are in it isn't said. Magpul states no weight."},"lugs":{"label":"M-LOK slots its lugs span","kind":"count","measurements":[{"id":"photo","value":1,"unit":"count","source":{"type":"photo","photo":"references/magpul-mlok-index-panel 68be85d611cb (US D755,334 S, Magpul, FIG. 7 top plan: the mounting face, in broken lines; the patent office's copy, page 8, 300 dpi)","scaleRef":"the plan view's length as the plate's (.length)","method":"one screw hole 0.385 in from the plate's rear end and a pair of bosses 0.787 in ahead of it, on a plate 1.558 in long: one 32 mm slot takes both, and the plate covers that slot's pitch","via":"harvest"}},{"id":"configurator","value":1,"unit":"count","stated":"The hand stop occupies two M-LOK slots, the index panel one slot, and the rail cover spans two.","source":{"type":"spec","publisher":"review","name":"rifleconfigurator.com, Magpul M-LOK Hand Stop Kit (a configurator site; source of the statement unstated)","url":"https://www.rifleconfigurator.com/catalog/controls/magpul-m-lok-hand-stop-kit","retrieved":"2026-10-05","via":"harvest"}}],"adopt":{"from":"photo","reason":"Read on Magpul's own drawing of the mounting face; the site's unattributed sentence says the same of this piece."},"note":"One screw and one T-nut (FIG. 7 draws one hole; Wing Tactical's photo of its mounting side shows one, and its photo of the kit's hardware three T-nuts: two for the hand stop). A second pair of bosses with no screw stands either side of the fin's hollow, one M-LOK interval from the screw: the two pairs go one in each half of a slot, and the plate covers that slot's pitch. Magpul's sheet names no count."},"reach_inside":{"label":"Reach inside the handguard (below the mounting face, tightened)","kind":"length","measurements":[],"note":"Not sourced (as for the hand stop and the MVG: Magpul publishes no T-nut figure). FIG. 3 draws the lug that stands in the slot 0.06 in above the band, in broken lines; the T-nut beyond it isn't drawn."},"lug_x":{"label":"Rear lug's centre ahead of the part's rear end (its screw and T-nut)","kind":"length","measurements":[{"id":"patent-bottom","value":0.387,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-mlok-index-panel 0c155e219281 (US D755,334 S, Magpul, FIG. 8 bottom plan; the patent office's copy, page 9, 300 dpi)","scaleRef":"the plan view's own length, 1866 px, as the plate's length (.length, 1.558 in)","method":"the screw hole's four circles, drawn in broken lines, fitted on one centre (row 2189.1, rms 0.6 to 0.7 px): 462.9 px from the plate's screw end (row 2652)","via":"harvest"}},{"id":"patent-top","value":0.385,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-mlok-index-panel 68be85d611cb (US D755,334 S, Magpul, FIG. 7 top plan: the mounting face, in broken lines; the patent office's copy, page 8, 300 dpi)","scaleRef":"the plan view's own length, 2044 px, as the plate's length (.length, 1.558 in)","method":"the screw hole's circle fitted (row 1178.6, rms 0.6 px): 505.6 px from the plate's screw end (row 673)","via":"harvest"}},{"id":"render","value":0.463,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-mlok-index-panel 0474c600d6a0 (Supplied in chat 2026-10-02: a gallery image of an M-LOK handguard, straight side view, the hand stop and the index panel installed, rail teeth along the top, 2796 x 1290)","scaleRef":"the handguard's rail teeth in the same image: 336.5 px/in","method":"the middle of the screw's head where it stands below the plate (u 2088.7 to 2160.9 at rows 790 to 793: 2124.8) from the plate's end on that side (u 2278.2 to 2283: 2280.6): 155.8 px; ± covers the end's 4.6 px and the head's 3","via":"user"}}],"adopt":{"from":"patent-bottom","reason":"Magpul's drawing, on which both plan views agree within 0.002 in, and which puts the screw half an M-LOK interval (10 mm) from the plate's middle, where a T-nut in a slot under the plate's middle goes. The image has the screw 0.08 in nearer the fin (8 mm from the plate's middle) and the fin as much nearer its end (fin_x), while the distance between the two agrees with the patent within 2%: its seams are what part from the drawing, and it is a rendering whose source page isn't on file."},"note":"The part's rear end is the plate's end away from the fin, as Magpul's pictures of the kit have it (the fin at the front of its plate, ahead of the hand stop). The second pair of bosses, either side of the fin's hollow, is 0.386 in from the front end and 0.787 in (20.0 mm) ahead of the screw: the middle of the two pairs is the plate's middle within 0.001 in."},"fin_x":{"label":"The fin's middle ahead of the part's rear end","kind":"length","measurements":[{"id":"patent-side","value":1.127,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-mlok-index-panel c190e3d7fbdd (US D755,334 S, Magpul, FIG. 5 left side elevation; the patent office's copy, page 6, 300 dpi)","scaleRef":"the side elevation's own length, 2163 px (rows 649 to 2811), as the plate's length (.length, 1.558 in)","method":"the middle of the fin's tip (rows 2099 to 2328: 2213.5) from the plate's far end (row 649): 1564.5 px. FIG. 8 has it at 0.7245 of the length (the fin's lines are symmetric about row 1300) and FIG. 7's hollow at 0.7248: 1.129 in both","via":"harvest"}},{"id":"render","value":1.19,"unit":"in","pm":0.016,"source":{"type":"photo","photo":"references/magpul-mlok-index-panel 0474c600d6a0 (Supplied in chat 2026-10-02: a gallery image of an M-LOK handguard, straight side view, the hand stop and the index panel installed, rail teeth along the top, 2796 x 1290)","scaleRef":"the handguard's rail teeth in the same image: 336.5 px/in","method":"the middle of the fin's two flanks (u 1880.0 at rows 860, 900 and 945, within 0.3 px) from the plate's far end (u 2278.2 to 2283: 2280.6): 400.6 px (with the screw's head, 244.8 px from the fin's middle: 0.728 in, where the patent has 0.740)","via":"user"}}],"adopt":{"from":"patent-side","reason":"Three views of Magpul's drawing agree within 0.002 in. The image has the fin 0.06 in nearer its end of the plate, and the screw with it (lug_x): see there."}},"fin_height":{"label":"The fin below the plate's outer face","kind":"length","measurements":[{"id":"patent","value":0.498,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-mlok-index-panel c190e3d7fbdd (US D755,334 S, Magpul, FIG. 5 left side elevation; the patent office's copy, page 6, 300 dpi)","scaleRef":"the side elevation's own length, 2163 px, as the plate's length (.length, 1.558 in)","method":"the plate's outer face (the heavy line at columns 1194 to 1199) to the fin's tip (the heavy line at columns 1886 to 1891): 692 px","via":"harvest"}},{"id":"render","value":0.49,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-mlok-index-panel 0474c600d6a0 (Supplied in chat 2026-10-02: a gallery image of an M-LOK handguard, straight side view, the hand stop and the index panel installed, rail teeth along the top, 2796 x 1290)","scaleRef":"the handguard's rail teeth in the same image: 336.5 px/in","method":"the plate's outer face on its smooth stretch (row 785.8 at half tone, u 1975 to 2030) to the fin's lowest point (row 950.8, u 1862 to 1900): 165.0 px. The fin's flanks lean 11.5 degrees each (98.6 px wide at row 860, 82.3 at row 900), the patent's 10.5 to 11","via":"user"}}],"adopt":{"from":"patent","reason":"The outline's own; the image agrees within 1.6%, which with the plate's length is the two sizes that agree at one scale."},"note":"The one height both sources show against white: the plate's own top is dark against the handguard in the image."},"screw_hole_diameter":{"label":"Screw hole (through the plate)","kind":"length","measurements":[{"id":"patent-bottom","value":0.219,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-mlok-index-panel 0c155e219281 (US D755,334 S, Magpul, FIG. 8 bottom plan; the patent office's copy, page 9, 300 dpi)","scaleRef":"the plan view's own length, 1866 px, as the plate's length (.length, 1.558 in)","method":"the innermost of the four broken-line circles, fitted: radius 130.9 px (rms 0.6). FIG. 7 draws the same hole from the mounting side: radius 143.6 px on a 2044 px plate, 0.219 in","via":"harvest"}}]},"screw_recess_diameter":{"label":"Screw's recess in the outer face, at its rim","kind":"length","measurements":[{"id":"patent-bottom","value":0.429,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-mlok-index-panel 0c155e219281 (US D755,334 S, Magpul, FIG. 8 bottom plan; the patent office's copy, page 9, 300 dpi)","scaleRef":"the plan view's own length, 1866 px, as the plate's length (.length, 1.558 in)","method":"the outermost of the four broken-line circles, fitted: radius 256.9 px (rms 0.7), on the hole's centre","via":"harvest"}}],"note":"FIG. 8 draws three circles round the hole in broken lines: this one, one of 0.400 in (radius 239.3 px) and screw_recess_floor_diameter. FIG. 2 shows them as a dish with the hole in its floor. How deep it is no view gives."},"screw_recess_floor_diameter":{"label":"Screw's recess in the outer face, the innermost of its three circles","kind":"length","measurements":[{"id":"patent-bottom","value":0.36,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-mlok-index-panel 0c155e219281 (US D755,334 S, Magpul, FIG. 8 bottom plan; the patent office's copy, page 9, 300 dpi)","scaleRef":"the plan view's own length, 1866 px, as the plate's length (.length, 1.558 in)","method":"the third circle in from the rim, fitted: radius 215.4 px (rms 0.6), on the hole's centre","via":"harvest"}}]},"mounting_band_depth":{"label":"Mounting face: the band between the ears, below the ears' tips","kind":"length","measurements":[{"id":"patent","value":0.111,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-mlok-index-panel 46bdaee98acd (US D755,334 S (Magpul, 'Index attachment for a firearm'), FIG. 3 front elevation, 300 dpi)","scaleRef":"the traced front elevation's own scale (profiles.front: magpul-mlok-index-panel.height and .width, 1355.6 px/in)","method":"the flat between the ears on the traced outline, at y 0.110 to 0.112 from z -0.345 to +0.339, against the ears' tips at y 0 (z ±0.50)","via":"harvest"}}],"note":"The band is what bears on a handguard's M-LOK face, as the hand stop's does (the same plate: its band is 0.116 in below its ears' tips and 0.698 across): the ears slope out and up from its edges and run down either side of a face narrower than the band. The drawing has it in broken lines (rows 735 to 737 and 749 of FIG. 3), with the lug that stands in the slot a broken box 0.06 in high and 0.27 in wide above it (a 7 mm slot's, std.mlok.slot_width); a third line 0.05 in further in, in solid dots, is the plate's end face. Wing Tactical's photo of the mounting side shows the flat band, the ears and the bosses."},"mounting_band_width":{"label":"Mounting face: the band between the ears, across","kind":"length","measurements":[{"id":"patent","value":0.684,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-mlok-index-panel 46bdaee98acd (US D755,334 S (Magpul, 'Index attachment for a firearm'), FIG. 3 front elevation, 300 dpi)","scaleRef":"the traced front elevation's own scale (profiles.front, 1355.6 px/in)","method":"the flat between the ears on the traced outline: z -0.345 to +0.339","via":"harvest"}}]},"screw_head_diameter":{"label":"Screw's head, across","kind":"length","measurements":[{"id":"gallery-fde","value":0.364,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/magpul-mlok-hand-stop 343c6dde53f4 (Magpul's gallery for MAG608, mag608_fde_2.png, 1200 x 1200: the FDE kit's pieces put together with their screws in, three-quarter from the outer side; filed with the hand stop)","scaleRef":"the recess's rim in the same view, as .screw_recess_diameter (0.429 in): both are circles on one axis a few hundredths of an inch apart in depth, so their long axes are in the ratio of their diameters","method":"the dark head's long axis 58.5 px (columns 323 to 383 at luminance under 75) against the rim's 69 px, read on a tenfold enlargement; ± covers a pixel and a half on each and the rim's soft edge","via":"harvest"}}],"note":"Magpul publishes no figure for the kit's screws. A wide low head with a six-lobe socket (Wing Tactical's photo of the kit's hardware: six alike). It is the recess's innermost circle (screw_recess_floor_diameter, 0.360 in) within the reading: the head fills the dish's floor."},"screw_head_proud":{"label":"Screw's head: its crown above the plate's outer face","kind":"length","measurements":[{"id":"render","value":0.034,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-mlok-index-panel 0474c600d6a0 (Supplied in chat 2026-10-02: a gallery image of an M-LOK handguard, straight side view, the hand stop and the index panel installed, rail teeth along the top, 2796 x 1290)","scaleRef":"the handguard's rail teeth in the same image: 336.5 px/in","method":"the plate's outer face at half tone on its smooth stretch (rows 785.4 to 786.7, u 1975 to 2025) to the head's lowest point (row 797.1, u 2124 to 2130): 11.5 px; ± covers 2 px and the face's own 1.3 px","via":"user"}}],"note":"A rendering whose source page isn't on file (lug_x's note: its seams part from the drawing; a height across 0.03 in doesn't depend on them)."}}},{"subject":"magpul-mlok-mvg","title":"Magpul M-LOK MVG vertical grip (MAG597)","dimensions":{"height":{"label":"Height (how far it stands off the handguard's face)","kind":"length","measurements":[{"id":"magpul","value":3,"unit":"in","pm":0.05,"stated":"Length 3.0 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, M-LOK MVG Vertical Grip (MAG597), Technical Specifications","url":"https://magpul.com/m-lok-mvg-vertical-grip.html","retrieved":"2026-10-02","via":"harvest"}},{"id":"wing","value":3,"unit":"in","pm":0.05,"stated":"Height: 3\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Magpul MVG M-LOK Vertical Grip (MAG-597), Specifications (source of the figures unstated)","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/grips-foregrips/foregrips/magpul-mvg-m-lok-vertical-grip/","retrieved":"2026-10-02","via":"harvest"}}],"adopt":{"from":"magpul","reason":"The maker's figure; the retailer's is the same number under another name."},"note":"Magpul calls the grip's long dimension its length; installed, it stands that far off the handguard. Wing Tactical prints the same figure as the height."},"length":{"label":"Overall length (along the handguard)","kind":"length","measurements":[{"id":"wing","value":1.54,"unit":"in","pm":0.02,"stated":"Length: 1.54\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Magpul MVG M-LOK Vertical Grip (MAG-597), Specifications (source of the figures unstated)","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/grips-foregrips/foregrips/magpul-mvg-m-lok-vertical-grip/","retrieved":"2026-10-02","via":"harvest"}}],"note":"One retailer's figure, whose source isn't stated. The side photo (tools/trace.py, dims calibration) scales by this and the height together and requires them to agree within 2%: they do (the plate's 580 px over the grip's 1119 px is 1.555 for 3.0)."},"width":{"label":"Width (side to side)","kind":"length","measurements":[{"id":"wing","value":1.17,"unit":"in","pm":0.02,"stated":"Width: 1.17\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Magpul MVG M-LOK Vertical Grip (MAG-597), Specifications (source of the figures unstated)","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/grips-foregrips/foregrips/magpul-mvg-m-lok-vertical-grip/","retrieved":"2026-10-02","via":"harvest"}}],"note":"One retailer's figure, whose source isn't stated, and nothing on file checks it: no straight end view of the grip is on any page found (Magpul's gallery _02, 1.54 in across for 3.0 tall, is the long side again). The 3/4 photos show the plate as an obround about that wide."},"weight":{"label":"Weight (with its T-nuts and screws)","kind":"mass","measurements":[{"id":"magpul","value":1.4,"unit":"oz","pm":0.05,"stated":"Weight, w/ hardware 1.4 oz.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, M-LOK MVG Vertical Grip (MAG597), Technical Specifications","url":"https://magpul.com/m-lok-mvg-vertical-grip.html","retrieved":"2026-10-02","via":"harvest"}},{"id":"wing","value":1.4,"unit":"oz","pm":0.05,"stated":"Weight: 1.4 oz.","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Magpul MVG M-LOK Vertical Grip (MAG-597), Specifications (source of the figures unstated)","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/grips-foregrips/foregrips/magpul-mvg-m-lok-vertical-grip/","retrieved":"2026-10-02","via":"harvest"}}],"adopt":{"from":"magpul","reason":"The maker's figure, which says what it includes."},"note":"Big Tex Ordnance's 4.8 oz is a shipping weight (listed beside a 3 x 2 x 2 in box) and isn't recorded."},"lugs":{"label":"M-LOK slots its lugs span","kind":"count","measurements":[{"id":"sheet","value":1,"unit":"count","stated":"Align the MVG using the two M-LOK lugs. Place the M-LOK T-Nuts and lugs into the slot at the desired location.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE M-LOK MVG installation instructions (MAG597_MOE_M-LOK_MVG_INSRT.pdf), Step 3","url":"https://magpul.com/media/wysiwyg/Instructions/MAG597_MOE_M-LOK_MVG_INSRT.pdf","retrieved":"2026-10-02","via":"harvest"}}],"note":"Both lugs and both T-nuts go into one slot: the two nuts sit the M-LOK interval (20 mm) apart inside a 32 mm slot (lug_spacing). The sheet names the slot in the singular, and its Step 3 picture shows the grip under one slot."},"lug_x":{"label":"Rear lug's centre ahead of the part's rear end","kind":"length","measurements":[{"id":"photo","value":0.383,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-mlok-mvg dc38ca0e3fdf (Primary Arms MAG597-ODG_00.jpg: the MVG alone on white, upright with its T-nuts on top, a straight side view along the handguard, 2000 x 1334)","scaleRef":"the plate's length, 580 px (712 to 1292) = magpul-mlok-mvg.length 1.54 in: 376.6 px/in; the grip's height, 1119 px (136 to 1255) = magpul-mlok-mvg.height 3.0 in: 373 px/in. The two agree within 1%; 375 px/in used","method":"same-plane ratio on a 3x gridded crop: the T-nut stems' centres (853 and 1145 px) against the plate's ends (712 and 1292 px); 0.373 from the left end and 0.392 from the right, the mean recorded with the difference in the ±","via":"harvest"}}],"note":"The two T-nuts are centred on the plate (0.37 and 0.39 in from either end); the grip is symmetric fore and aft, and Magpul's FAQ says an M-LOK accessory mounts facing either way, so which end is the rear is the user's choice (`flipped`)."},"lug_spacing":{"label":"Distance between the two T-nuts (centre to centre)","kind":"length","measurements":[{"id":"photo","value":0.779,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-mlok-mvg dc38ca0e3fdf (Primary Arms MAG597-ODG_00.jpg, as above)","scaleRef":"375 px/in (the plate's length and the grip's height, agreeing within 1%)","method":"the T-nut stems' centres, 853 and 1145 px: 292 px","via":"harvest"}}],"note":"19.8 mm: the M-LOK interval (std.mlok.interval, 20 mm), as a two-nut accessory that mounts within one slot has to have."},"reach_inside":{"label":"Reach inside the handguard (below the mounting face, tightened)","kind":"length","measurements":[],"note":"Not sourced. Magpul publishes no T-nut dimensions (its M-LOK FAQ: drawings of the nut are restricted pending an ITAR review), and the installation sheet sets the nut by the surface's thickness, not by a figure. Until one is found, the check against the handguard's room (data/interfaces.yaml, mlok) can't be made, and the app says so."},"rib_grooves":{"label":"Grooves across each end (front and rear)","kind":"count","measurements":[{"id":"photo","value":16,"unit":"count","source":{"type":"photo","photo":"references/magpul-mlok-mvg dc38ca0e3fdf (Primary Arms MAG597-ODG_00.jpg: the MVG alone on white, upright with its T-nuts on top, a straight side view along the handguard, 2000 x 1334)","scaleRef":"a count: none","method":"the silhouette's edge at each end, row by row (luminance 215, sub-pixel), against a line through its crests: 16 notches deeper than 4 px at each end, and one shallow step below them where the foot begins (4 px, the left end only), which isn't a groove","via":"harvest"}},{"id":"patent","value":16,"unit":"count","source":{"type":"photo","photo":"references/magpul-mlok-mvg 2da0ba7d369f (US D745,628 S, sheet 2, FIG. 2 front elevation, 300 dpi)","scaleRef":"a count: none","method":"the obrounds drawn down the front, counted","via":"harvest"}}],"adopt":{"from":"photo","reason":"The part itself; the patent's drawing has the same number."}},"rib_groove_pitch":{"label":"Grooves' pitch down the grip","kind":"length","measurements":[{"id":"photo","value":0.0856,"unit":"in","pm":0.002,"source":{"type":"photo","photo":"references/magpul-mlok-mvg dc38ca0e3fdf (Primary Arms MAG597-ODG_00.jpg, as above)","scaleRef":"the side outline's scale: magpul-mlok-mvg.height and magpul-mlok-mvg.length together, 378.8 px/in (they agree within 1.3%, which is the ±)","method":"a line through the 16 grooves' centres (each the middle of its half-depth crossings) at each end: 32.53 px a groove at the left end and 32.32 at the right, no centre more than 1.8 px off its line; the mean","via":"harvest"}}],"note":"The patent's FIG. 2 draws them 48.5 px apart where its body is 683 px wide: 0.083 in by the width on file, and 0.087 once its height is put to the grip's (its proportions are 5% off the figures on file)."},"rib_groove_first_y":{"label":"First groove's centre below the mounting face","kind":"length","measurements":[{"id":"photo","value":1.389,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-mlok-mvg dc38ca0e3fdf (Primary Arms MAG597-ODG_00.jpg, as above)","scaleRef":"the side outline's scale, 378.8 px/in","method":"the fitted lines' first centres, row 660.1 at the left end and 665.4 at the right, below the outline's top (row 136.5): the mean. The two ends differ by 5 px across 585: the photo's half a degree of roll, which is the ±","via":"harvest"}}]},"rib_groove_depth":{"label":"Grooves' depth","kind":"length","measurements":[{"id":"photo","value":0.028,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/magpul-mlok-mvg dc38ca0e3fdf (Primary Arms MAG597-ODG_00.jpg, as above)","scaleRef":"the side outline's scale, 378.8 px/in","method":"each notch's deepest row below the line through the crests: 11.0 px on average at the left end (9.7 to 12.4) and 9.9 at the right (7.6 to 12.3); the mean of the two, with their spread in the ±","via":"harvest"}}],"note":"At the grip's middle, where the side view sees them. The patent's bottom plan (FIG. 7) has two lines inside its outline at each end that its sides don't have, 0.011 and 0.038 in in: neither is labelled, and nothing is taken from them."},"rib_groove_width":{"label":"Grooves' width (down the grip, at half their depth)","kind":"length","measurements":[{"id":"photo","value":0.048,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/magpul-mlok-mvg dc38ca0e3fdf (Primary Arms MAG597-ODG_00.jpg, as above)","scaleRef":"the side outline's scale, 378.8 px/in","method":"each notch's rows at or below half its depth: 19.7 px on average at the left end and 16.4 at the right; the mean of the two, their difference in the ±","via":"harvest"}}],"note":"The patent's FIG. 2 draws each obround 28 px tall at a 48.5 px pitch, 0.58 of it: 0.049 in at the pitch on file."},"rib_groove_length":{"label":"Grooves' length (across the grip, tip to tip as the front view sees them)","kind":"length","measurements":[{"id":"patent","value":0.7,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-mlok-mvg 2da0ba7d369f (US D745,628 S, sheet 2, FIG. 2 front elevation, 300 dpi)","scaleRef":"the body's width in the same figure, 683 px (columns 492 to 1175), as magpul-mlok-mvg.width 1.17 in: 584 px/in","method":"each obround's length, 408 px (columns 630 to 1038, centred on the body's middle within a pixel): 0.597 of the width. The ± is the lines' own 4 px and the width's ± at that share","via":"harvest"}}],"note":"The same in FIG. 3, the rear. The side photo agrees (dc38ca0e3fdf, at 378.8 px/in): its grooves' inner ends show 46 px in from the crests' edge at the left end and 47 at the right, 0.12 in, and the patent's section (profiles.plan) is 0.127 in in from its end at 0.35 in off the centre line. The bottom plan (FIG. 7) has a tick across its rim at each of four corners, 0.26 to 0.41 in off the centre line, where the grooved ends meet the sides."},"base_wall":{"label":"Wall round the base's opening","kind":"length","measurements":[{"id":"patent","value":0.115,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-mlok-mvg 9d49858cd908 (US D745,628 S, sheet 5, FIG. 7 bottom plan, 300 dpi)","scaleRef":"the figure's outline, 955 x 721 px, as magpul-mlok-mvg.length 1.54 in and magpul-mlok-mvg.width 1.17 in: 620 and 616 px/in, 618 used","method":"the band from the outline to the innermost solid line, on the two centre lines: 74.5 px at each end (0.121 in) and 67 px at each side (0.108 in); the mean, the difference in the ±. The opening is 1.30 x 0.95 in","via":"harvest"}}],"note":"The grip is hollow and open at its base: the installation sheet's Step 1 is \"Insert the Screws through the bottom of the M-LOK MVG and thread the T-Nuts with the “stem” of the nut facing towards the grip\", and Magpul's photos from below (597_3, 597_5, gallery _03) show the opening and its rim. The innermost solid line of the bottom plan is taken to be the opening's edge: inside it the patent draws nothing but a broken line."}}},{"subject":"magpul-mlok-polymer-rail-section-11-slot","title":"Magpul M-LOK® Polymer Rail, 11 Slots (MAG593)","dimensions":{"length":{"label":"Overall length (along the handguard)","kind":"length","measurements":[{"id":"page","value":4.9,"unit":"in","pm":0.05,"stated":"4.9\" 11-slot Picatinny rail segment easily attaches to any M-LOK mounting interface","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, M-LOK® Polymer Rail, 11 Slots (MAG593), Product Details","url":"https://magpul.com/m-lokpolymerrailsection-11slots.html","retrieved":"2026-10-29","via":"harvest"}},{"id":"gis","value":4.9,"unit":"in","pm":0.05,"stated":"MAG593 - 11 Slots, max overall length of 4.9” NSN:1005017254945","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, M-LOK® Polymer Rail Sections GIS sheet (MAG589-MAG593), page 1","url":"https://magpul.com/media/wysiwyg/GIS/MAG589-MAG593_M-LOK_Polymer_Rail_Sections_GIS_01.pdf","retrieved":"2026-10-29","via":"harvest"}},{"id":"top-view","value":4.706,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-11-slot 4f6ad115bb6f (Magpul's mag593-feature_01, 700 x 525: the 11-slot on a hand guard's side face, three screws in, seen square on)","scaleRef":"its own rail slots at the standard's pitch (std.picatinny.slot_pitch, 0.394 in: Magpul's sheet, \"1913 Picatinny spec rail-mounted accessories\"): the slots' edges along a strip under its top edge (rows 220 to 232), eleven alike 40.36 px apart (a straight fit from 140.2 to 543.8 over ten): 102.4 px/in","method":"the outline's two ends on that strip, where its lit sloped ends meet the hand guard: columns 90.9 and 573.1, 482.2 px; ± covers 2 px at each end","via":"harvest"}},{"id":"studio","value":4.682,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-11-slot ebf055d321c3 (Magpul's mag593-blk_01, 1200 x 1200: the 11-slot alone on white, from above and in front, no screws in)","scaleRef":"its own rail slots at the standard's pitch (std.picatinny.slot_pitch, 0.394 in: Magpul's sheet, \"1913 Picatinny spec rail-mounted accessories\"): its lands' rear edges on the turned photo, 98.2 px apart","method":"the image turned 26.8 degrees so the part's long axis runs across; the outline's extent along it, 1167 px: 11.88 pitches","via":"harvest"}}],"adopt":{"from":"top-view","reason":"Read on Magpul's own photo of this length, scaled by its own rail slots at the standard's pitch (std.picatinny.slot_pitch, 0.394 in: Magpul's sheet, \"1913 Picatinny spec rail-mounted accessories\"). Magpul's \"4.9\" is a maximum it states for the length in tenths, and every one of the five lengths, read the same way on its own photos, is its end-to-end rail slots (11 less one pitches) and 0.76 to 0.79 in more: 0.12 to 0.18 in under Magpul's figure from the 5-slot up (the 3-slot's 0.03). Drawn at Magpul's figure with the slots on the standard's pitch, its ends would be a tenth of an inch longer than any photo shows them; Magpul's own word is that the rail is the 1913 standard's. Its square view and its studio photo agree within 0.03 in."},"note":"The outline's two ends along the rail. On the square view the slots are 0.397 in from the rear end to the rear slot's centre and 0.365 from the front slot's centre to the front end."},"height":{"label":"Height (its rail's top above the handguard's face it sits on)","kind":"length","measurements":[{"id":"assumed","value":0.33,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no photo of this length shows its side well enough to read. Magpul's studio photos of the 7-slot and the 9-slot, read the same way (the top flat's foreshortening against the standard's 0.656 in for the camera's elevation, the band below it for the side), give 0.316 and 0.345 in; Magpul's sheet and pages describe the five lengths as one moulding in five lengths. The ± covers both.","via":"harvest"}}],"note":"From the mounting face (the face that bears on the hand guard) to the rail's top."},"width":{"label":"Width (side to side, at its widest under the rail's head)","kind":"length","measurements":[{"id":"top-view","value":0.79,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-11-slot 4f6ad115bb6f (Magpul's mag593-feature_01, 700 x 525: the 11-slot on a hand guard's side face, three screws in, seen square on)","scaleRef":"the length's scale (102.4 px/in, its own slots)","method":"its outline across a column band through its middle (columns 300 to 330): from its top edge, row 219, to the hand guard's opening beside its lower edge, about row 300: 81 px; ± covers the lower edge, which is dark on dark","via":"harvest"}}],"note":"Across, square on. The rail's head is the standard's (0.835 in at its widest)."},"weight":{"label":"Weight (the moulding)","kind":"mass","measurements":[{"id":"model","value":0.562,"unit":"oz","pm":0.17,"source":{"type":"derived","basis":"The model's polymer volume, 0.8523 cubic inches (the manifest's body_volume_in3; the screws' heads apart), times std.density.polymer (Zytel nylon 66, 18.68 g, 0.659 oz to the cubic inch): 0.562 oz. Magpul names no grade (\"a proprietary reinforced composite\"): a glass-filled grade is up to a sixth heavier, the underside's pocket isn't drawn (the model is solid under its rail), and the height and the neck are readings or assumptions with their own ±; the ± takes all of them. The steel T-nuts and screws aren't in it.","via":"harvest"}}],"note":"Magpul states none. Worked out from the model (the weight's own entry says how)."},"rail_slots":{"label":"Rail slots","kind":"count","measurements":[{"id":"name","value":11,"unit":"count","stated":"M-LOK® Polymer Rail, 11 Slots","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, M-LOK® Polymer Rail, 11 Slots (MAG593), Product Details","url":"https://magpul.com/m-lokpolymerrailsection-11slots.html","retrieved":"2026-10-29","via":"harvest"}},{"id":"photo","value":11,"unit":"count","source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-11-slot 4f6ad115bb6f (Magpul's mag593-feature_01, 700 x 525: the 11-slot on a hand guard's side face, three screws in, seen square on)","scaleRef":"none: a count","method":"eleven slots between its two ends (the strip's eleven alike, 40.36 px apart), a screw in the second, the sixth and the tenth (the same on the studio photo)","via":"harvest"}}],"adopt":{"from":"photo","reason":"Counted on the part; the name says the same."}},"rail_slot0_x":{"label":"Rear rail slot's centre ahead of the part's rear end","kind":"length","measurements":[{"id":"centred","value":0.383,"unit":"in","source":{"type":"derived","expr":"({.length} - ({.rail_slots} - 1) * {std.picatinny.slot_pitch}) / 2","via":"harvest"}}],"note":"Centred on its length: the square view has 0.397 and 0.365 in at its two ends, within its reading."},"rear_hole_slot":{"label":"Rail slot its rear screw hole is in (counted from its rear end, the first is 1)","kind":"count","measurements":[{"id":"photo","value":2,"unit":"count","source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-11-slot 4f6ad115bb6f (Magpul's mag593-feature_01, 700 x 525: the 11-slot on a hand guard's side face, three screws in, seen square on)","scaleRef":"none: a count","method":"screws at columns 172.3, 334.3 and 495.7, each at the centre of the second, the sixth and the tenth of the slots (131.7 + 40.36 k); on the studio photo the same three slots have the holes","via":"harvest"}}]},"hole_pitches":{"label":"Rail slots from its rear screw hole to its front one (pitches)","kind":"count","measurements":[{"id":"photo","value":8,"unit":"count","source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-11-slot 4f6ad115bb6f (Magpul's mag593-feature_01, 700 x 525: the 11-slot on a hand guard's side face, three screws in, seen square on)","scaleRef":"none: a count","method":"screws at columns 172.3, 334.3 and 495.7, each at the centre of the second, the sixth and the tenth of the slots (131.7 + 40.36 k); on the studio photo the same three slots have the holes","via":"harvest"}}],"note":"Three screw holes, in the second, the sixth and the tenth slots, four pitches (40 mm, an M-LOK slot pitch) apart: the end holes eight pitches apart (3.152 in, 80 mm), a slot short of each end. The model draws a screw in each end hole."},"middle_hole_pitches":{"label":"Rail slots from its rear screw hole to its middle one (pitches)","kind":"count","measurements":[{"id":"photo","value":4,"unit":"count","source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-11-slot 4f6ad115bb6f (Magpul's mag593-feature_01, 700 x 525: the 11-slot on a hand guard's side face, three screws in, seen square on)","scaleRef":"none: a count","method":"screws at columns 172.3, 334.3 and 495.7, each at the centre of the second, the sixth and the tenth of the slots (131.7 + 40.36 k); on the studio photo the same three slots have the holes","via":"harvest"}}],"note":"The middle hole is the 'intermediate spacing option' of Magpul's sheet, as far as the photos show: two screws come with it (sellers' words), and any two of the three holes take them."},"lugs":{"label":"M-LOK slots its T-nuts span","kind":"count","measurements":[{"id":"holes","value":3,"unit":"count","source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-11-slot 4f6ad115bb6f (Magpul's mag593-feature_01, 700 x 525: the 11-slot on a hand guard's side face, three screws in, seen square on)","scaleRef":"none: a count","method":"its end screws eight rail pitches apart (3.152 in, 80 mm): a T-nut in the rear half of one slot and the other in the rear half of the slot two on","via":"harvest"}}],"note":"Three M-LOK slots, with screws in its two end holes."},"lug_x":{"label":"Its seat on the M-LOK face: the centre of the M-LOK slot its rear T-nut is in, ahead of its rear end","kind":"length","measurements":[{"id":"rear-nut","value":1.1707,"unit":"in","source":{"type":"derived","expr":"{.rail_slot0_x} + ({.rear_hole_slot} - 1) * {std.picatinny.slot_pitch} + {std.mlok.interval} / 2","via":"harvest"}}],"note":"The rear screw hole is at its slot's centre (the photos), and its T-nut sits in the rear half of an M-LOK slot, half the M-LOK interval behind that slot's centre: what an M-LOK position places is that slot's centre. Two T-nuts the interval apart then sit one in each half of one slot (the 3-slot: the hand stop's seat); one a slot pitch further on sits in the rear half of the next. Magpul's page: \"Integral recoil lugs resist impact and keep rail secured under recoil and provide an intermediate spacing option\" (the lugs under it between its nuts, which go into a slot), and its M-LOK page: \"Your M-LOK accessory can be adjusted in 20mm increments (1/2 slot length)\". Which half of a slot a nut is in isn't published: the rear half is assumed."},"reach_inside":{"label":"Reach inside the handguard (below the mounting face, tightened)","kind":"length","measurements":[],"note":"Not published: Magpul gives no figure for its cammed T-nuts or for the recoil lugs under the section."},"neck_top_below_top":{"label":"Under the head: where its lower faces, carried on at 45 degrees past the lower gauge line, meet the neck, below the rail's top","kind":"length","measurements":[{"id":"assumed","value":0.2,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view of the part along its rail is on file, and the neck stands in the head's shadow in every photo. The head's lower faces are carried on at the standard's 45 degrees to here, as Midwest Industries' drop-in rail's are to theirs (0.204 in, read on its photo), so that what clamps a rail has room for its jaws under the head; the ± covers a neck from the standard's lower gauge width to two tenths narrower.","via":"harvest"}}],"note":"The head's lower faces are MIL-STD-1913's to its lower gauge line (std.picatinny.lower_gauge_below_top); under them the section narrows to a neck that leaves a clamp's jaws room under the head, then widens again to its width at a shoulder near the mounting face (neck_foot_above_face). With the standard's head (lib.rail_half) this sets the neck's half width."},"neck_foot_above_face":{"label":"Under the head: the neck's foot (the shoulder where the section widens to its width) above the mounting face","kind":"length","measurements":[{"id":"assumed","value":0.055,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no photo of this length's side shows its shoulder. The 5-slot's underside photo (e389e392fb30) reads 0.055 in; the ± covers it.","via":"harvest"}}]},"end_bevel_length":{"label":"Each end's slope, along the part: from the end to where its rail's top begins","kind":"length","measurements":[{"id":"top-view","value":0.26,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-11-slot 4f6ad115bb6f (Magpul's mag593-feature_01, 700 x 525: the 11-slot on a hand guard's side face, three screws in, seen square on)","scaleRef":"the length's scale (102.4 px/in)","method":"where the lit slope ends and its top begins: columns 119.0 and 547.4, 28.1 and 25.7 px in from the two ends","via":"harvest"}}],"note":"Magpul: \"The beveled ends reduce snagging and eliminate sharp corners and edges.\" The end face slopes and rounds down from the top to a short upright face at the mounting face (the photos from above and from the end)."},"end_face_height":{"label":"Each end's upright face under its slope, above the mounting face","kind":"length","measurements":[{"id":"assumed","value":0.08,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows it in profile.","via":"harvest"}}]},"end_corner_chamfer":{"label":"Each end's corners cut off in plan, along the end","kind":"length","measurements":[{"id":"assumed","value":0.13,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: its square view has its ends against the dark hand guard, its corners not clear. The 3-slot's top view has 0.13 in.","via":"harvest"}}]},"counterbore_diameter":{"label":"Each screw hole's recess, across","kind":"length","measurements":[{"id":"top-view","value":0.41,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-11-slot 4f6ad115bb6f (Magpul's mag593-feature_01, 700 x 525: the 11-slot on a hand guard's side face, three screws in, seen square on)","scaleRef":"the length's scale (102.4 px/in)","method":"the dark round each screw's head stands in, 41.7 px across on a threefold enlargement, by eye (on the studio photo the recesses' dark runs into the slots' shadows: 0.29 to 0.53 in, not read)","via":"harvest"}}],"note":"A round recess round each screw hole, into the slot it is in and the lands either side of it (every photo of the part from above)."},"counterbore_floor":{"label":"The recess's floor above the mounting face (where the screw's head bears)","kind":"length","measurements":[{"id":"assumed","value":0.12,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows it in profile.","via":"harvest"}}]},"hole_diameter":{"label":"Screw hole, through","kind":"length","measurements":[{"id":"studio","value":0.2,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-11-slot ebf055d321c3 (Magpul's mag593-blk_01, 1200 x 1200: the 11-slot alone on white, from above and in front, no screws in)","scaleRef":"the length's scale (249.2 px/in along the turned photo, its own slots)","method":"the image turned along the part (as for the length); along the row through each hole's centre, the white of the hole (over 170 of 255) and the dark of the recess round it (under 85, past the hole's rim) (.cache/batch16, recess.py): the white of its three holes 47, 53 and 52 px, 0.189, 0.213 and 0.209 in","via":"harvest"}}]},"screw_head_diameter":{"label":"Screw's head, across","kind":"length","measurements":[{"id":"assumed","value":0.34,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: its head stands inside its recess in every photo of this length with its screws in, and none reads it apart from the recess. The 3-slot's top view has its head 0.034 in inside its recess's rim.","via":"harvest"}}],"note":"Its two screws are black socket button heads (Magpul's photo of the hardware under the 5- and 7-slot sections: two screws and two T-nuts)."},"screw_head_height":{"label":"Screw's head, from the recess's floor to its crown","kind":"length","measurements":[{"id":"assumed","value":0.06,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows it in profile.","via":"harvest"}}]}}},{"subject":"magpul-mlok-polymer-rail-section-3-slot","title":"Magpul M-LOK® Polymer Rail, 3 Slots (MAG589)","dimensions":{"length":{"label":"Overall length (along the handguard)","kind":"length","measurements":[{"id":"page","value":1.6,"unit":"in","pm":0.05,"stated":"1.6\" 3-slot Picatinny rail segment easily attaches to any M-LOK mounting interface","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, M-LOK® Polymer Rail, 3 Slots (MAG589), Product Details","url":"https://magpul.com/m-lokpolymerrailsection-3slots.html","retrieved":"2026-10-29","via":"harvest"}},{"id":"gis","value":1.6,"unit":"in","pm":0.05,"stated":"MAG589 - 3 Slots, max overall length of 1.6”  NSN:1005016660491","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, M-LOK® Polymer Rail Sections GIS sheet (MAG589-MAG593), page 1","url":"https://magpul.com/media/wysiwyg/GIS/MAG589-MAG593_M-LOK_Polymer_Rail_Sections_GIS_01.pdf","retrieved":"2026-10-29","via":"harvest"}},{"id":"top-view","value":1.575,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-3-slot e3ddcc48fd99 (Magpul's mag589-feature_01, 700 x 525: the 3-slot on a MOE M-LOK hand guard's top face, its two screws in, seen square from above)","scaleRef":"its own rail slots at the standard's pitch (std.picatinny.slot_pitch, 0.394 in: Magpul's sheet, \"1913 Picatinny spec rail-mounted accessories\"): the three slots' centres at columns 228.3, 347.5 and 463.5, 117.6 px apart: 298.5 px/in","method":"the outline's two ends on the rows through its middle (the white ground beside the hand guard), columns 111.7 and 581.7: 470 px; ± covers 2 px at each end and the pitch's ± 1.5 px","via":"harvest"}}],"adopt":{"from":"top-view","reason":"Read square on, on a white ground, by its own slots; Magpul's \"max overall length of 1.6\" says the same within its last digit."},"note":"The two ends of its outline, square from above. The slots are centred on it: 116.6 px from the rear end to the rear slot's centre, 118.2 from the front slot's centre to the front end."},"height":{"label":"Height (its rail's top above the handguard's face it sits on)","kind":"length","measurements":[{"id":"assumed","value":0.33,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no photo of this length shows its side well enough to read. Magpul's studio photos of the 7-slot and the 9-slot, read the same way (the top flat's foreshortening against the standard's 0.656 in for the camera's elevation, the band below it for the side), give 0.316 and 0.345 in; Magpul's sheet and pages describe the five lengths as one moulding in five lengths. The ± covers both.","via":"harvest"}}],"note":"From the mounting face (the face that bears on the hand guard) to the rail's top."},"width":{"label":"Width (side to side, at its widest under the rail's head)","kind":"length","measurements":[{"id":"top-view","value":0.811,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-3-slot e3ddcc48fd99 (Magpul's mag589-feature_01, 700 x 525: the 3-slot on a MOE M-LOK hand guard's top face, its two screws in, seen square from above)","scaleRef":"the length's scale (298.5 px/in, its own slots)","method":"the outline across its middle (columns 330 to 370 averaged): rows 151 to 393 at half tone, 242 px; ± covers 2 px at each edge","via":"harvest"}}],"note":"The outline across, from above: the rail's head is the standard's (0.835 in at its widest), and the outline reads 0.811; the model takes this as its body under the head."},"weight":{"label":"Weight (the moulding)","kind":"mass","measurements":[{"id":"model","value":0.172,"unit":"oz","pm":0.05,"source":{"type":"derived","basis":"The model's polymer volume, 0.2617 cubic inches (the manifest's body_volume_in3; the screws' heads apart), times std.density.polymer (Zytel nylon 66, 18.68 g, 0.659 oz to the cubic inch): 0.172 oz. Magpul names no grade (\"a proprietary reinforced composite\"): a glass-filled grade is up to a sixth heavier, the underside's pocket isn't drawn (the model is solid under its rail), and the height and the neck are readings or assumptions with their own ±; the ± takes all of them. The steel T-nuts and screws aren't in it.","via":"harvest"}}],"note":"Magpul states none. Worked out from the model (the weight's own entry says how)."},"rail_slots":{"label":"Rail slots","kind":"count","measurements":[{"id":"name","value":3,"unit":"count","stated":"M-LOK® Polymer Rail, 3 Slots","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, M-LOK® Polymer Rail, 3 Slots (MAG589), Product Details","url":"https://magpul.com/m-lokpolymerrailsection-3slots.html","retrieved":"2026-10-29","via":"harvest"}},{"id":"photo","value":3,"unit":"count","source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-3-slot e3ddcc48fd99 (Magpul's mag589-feature_01, 700 x 525: the 3-slot on a MOE M-LOK hand guard's top face, its two screws in, seen square from above)","scaleRef":"none: a count","method":"three slots between its two ends, a screw in the first and the third","via":"harvest"}}],"adopt":{"from":"photo","reason":"Counted on the part; the name says the same."}},"rail_slot0_x":{"label":"Rear rail slot's centre ahead of the part's rear end","kind":"length","measurements":[{"id":"centred","value":0.3935,"unit":"in","source":{"type":"derived","expr":"({.length} - ({.rail_slots} - 1) * {std.picatinny.slot_pitch}) / 2","via":"harvest"}}],"note":"Centred on its length: the top view has 116.6 px from its rear end to the rear slot's centre and 118.2 from the front slot's centre to the front end."},"rear_hole_slot":{"label":"Rail slot its rear screw hole is in (counted from its rear end, the first is 1)","kind":"count","measurements":[{"id":"photo","value":1,"unit":"count","source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-3-slot e3ddcc48fd99 (Magpul's mag589-feature_01, 700 x 525: the 3-slot on a MOE M-LOK hand guard's top face, its two screws in, seen square from above)","scaleRef":"none: a count","method":"the two screws' centres at columns 228 and 463, within 1 px of the first and the third slots' centres","via":"harvest"}}]},"hole_pitches":{"label":"Rail slots from its rear screw hole to its front one (pitches)","kind":"count","measurements":[{"id":"photo","value":2,"unit":"count","source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-3-slot e3ddcc48fd99 (Magpul's mag589-feature_01, 700 x 525: the 3-slot on a MOE M-LOK hand guard's top face, its two screws in, seen square from above)","scaleRef":"none: a count","method":"the two screws' centres at columns 228 and 463, within 1 px of the first and the third slots' centres","via":"harvest"}}],"note":"Two screw holes, one in each end slot, two pitches apart (0.788 in): the M-LOK interval (20 mm), so its two T-nuts go into the two halves of one M-LOK slot."},"lugs":{"label":"M-LOK slots its T-nuts span","kind":"count","measurements":[{"id":"holes","value":1,"unit":"count","source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-3-slot e3ddcc48fd99 (Magpul's mag589-feature_01, 700 x 525: the 3-slot on a MOE M-LOK hand guard's top face, its two screws in, seen square from above)","scaleRef":"none: a count","method":"its two screws two rail pitches apart (0.788 in, the M-LOK interval): both T-nuts in one M-LOK slot","via":"harvest"}}],"note":"One M-LOK slot: its two T-nuts 20 mm apart in its two halves, as Magpul's hand stop's."},"lug_x":{"label":"Its seat on the M-LOK face: the centre of the M-LOK slot its rear T-nut is in, ahead of its rear end","kind":"length","measurements":[{"id":"rear-nut","value":0.7872,"unit":"in","source":{"type":"derived","expr":"{.rail_slot0_x} + ({.rear_hole_slot} - 1) * {std.picatinny.slot_pitch} + {std.mlok.interval} / 2","via":"harvest"}}],"note":"The rear screw hole is at its slot's centre (the photos), and its T-nut sits in the rear half of an M-LOK slot, half the M-LOK interval behind that slot's centre: what an M-LOK position places is that slot's centre. Two T-nuts the interval apart then sit one in each half of one slot (the 3-slot: the hand stop's seat); one a slot pitch further on sits in the rear half of the next. Magpul's page: \"Integral recoil lugs resist impact and keep rail secured under recoil and provide an intermediate spacing option\" (the lugs under it between its nuts, which go into a slot), and its M-LOK page: \"Your M-LOK accessory can be adjusted in 20mm increments (1/2 slot length)\". Which half of a slot a nut is in isn't published: the rear half is assumed."},"reach_inside":{"label":"Reach inside the handguard (below the mounting face, tightened)","kind":"length","measurements":[],"note":"Not published: Magpul gives no figure for its cammed T-nuts or for the recoil lugs under the section."},"neck_top_below_top":{"label":"Under the head: where its lower faces, carried on at 45 degrees past the lower gauge line, meet the neck, below the rail's top","kind":"length","measurements":[{"id":"assumed","value":0.2,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view of the part along its rail is on file, and the neck stands in the head's shadow in every photo. The head's lower faces are carried on at the standard's 45 degrees to here, as Midwest Industries' drop-in rail's are to theirs (0.204 in, read on its photo), so that what clamps a rail has room for its jaws under the head; the ± covers a neck from the standard's lower gauge width to two tenths narrower.","via":"harvest"}}],"note":"The head's lower faces are MIL-STD-1913's to its lower gauge line (std.picatinny.lower_gauge_below_top); under them the section narrows to a neck that leaves a clamp's jaws room under the head, then widens again to its width at a shoulder near the mounting face (neck_foot_above_face). With the standard's head (lib.rail_half) this sets the neck's half width."},"neck_foot_above_face":{"label":"Under the head: the neck's foot (the shoulder where the section widens to its width) above the mounting face","kind":"length","measurements":[{"id":"assumed","value":0.055,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no photo of this length's side shows its shoulder. The 5-slot's underside photo (e389e392fb30) reads 0.055 in; the ± covers it.","via":"harvest"}}]},"end_bevel_length":{"label":"Each end's slope, along the part: from the end to where its rail's top begins","kind":"length","measurements":[{"id":"top-view","value":0.195,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-3-slot e3ddcc48fd99 (Magpul's mag589-feature_01, 700 x 525: the 3-slot on a MOE M-LOK hand guard's top face, its two screws in, seen square from above)","scaleRef":"the length's scale (298.5 px/in)","method":"where the top's flat ends and the slope begins: columns 168.3 and 521.7, 56.6 and 60.0 px in from the two ends","via":"harvest"}}],"note":"Magpul: \"The beveled ends reduce snagging and eliminate sharp corners and edges.\" The end face slopes and rounds down from the top to a short upright face at the mounting face (the photos from above and from the end)."},"end_face_height":{"label":"Each end's upright face under its slope, above the mounting face","kind":"length","measurements":[{"id":"assumed","value":0.08,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows it in profile.","via":"harvest"}}]},"end_corner_chamfer":{"label":"Each end's corners cut off in plan, along the end","kind":"length","measurements":[{"id":"top-view","value":0.13,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-3-slot e3ddcc48fd99 (Magpul's mag589-feature_01, 700 x 525: the 3-slot on a MOE M-LOK hand guard's top face, its two screws in, seen square from above)","scaleRef":"the length's scale (298.5 px/in)","method":"the outline's corners at the ends cut on a slant from about 46 px along the side to 38 px across the end; ± covers reading the slant's ends by eye","via":"harvest"}}]},"counterbore_diameter":{"label":"Each screw hole's recess, across","kind":"length","measurements":[{"id":"top-view","value":0.43,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-3-slot e3ddcc48fd99 (Magpul's mag589-feature_01, 700 x 525: the 3-slot on a MOE M-LOK hand guard's top face, its two screws in, seen square from above)","scaleRef":"the length's scale (298.5 px/in)","method":"the recess's rim round each screw, 128 px across on a threefold enlargement read by eye","via":"harvest"}}],"note":"A round recess round each screw hole, into the slot it is in and the lands either side of it (every photo of the part from above)."},"counterbore_floor":{"label":"The recess's floor above the mounting face (where the screw's head bears)","kind":"length","measurements":[{"id":"assumed","value":0.12,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows it in profile.","via":"harvest"}}]},"hole_diameter":{"label":"Screw hole, through","kind":"length","measurements":[{"id":"studio","value":0.21,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-3-slot c2202d475599 (Magpul's mag589-blk_01, 1200 x 1200: the 3-slot alone from above and in front, no screws in)","scaleRef":"the hole against its recess (.counterbore_diameter) on one circle's axis","method":"the white hole about half its recess's width, by eye","via":"harvest"}}]},"screw_head_diameter":{"label":"Screw's head, across","kind":"length","measurements":[{"id":"top-view","value":0.396,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-3-slot e3ddcc48fd99 (Magpul's mag589-feature_01, 700 x 525: the 3-slot on a MOE M-LOK hand guard's top face, its two screws in, seen square from above)","scaleRef":"the length's scale (298.5 px/in)","method":"each screw's dark head (its knurled rim), 118 px across on a threefold enlargement read by eye","via":"harvest"}}],"note":"Its two screws are black socket button heads (Magpul's photo of the hardware under the 5- and 7-slot sections: two screws and two T-nuts)."},"screw_head_height":{"label":"Screw's head, from the recess's floor to its crown","kind":"length","measurements":[{"id":"assumed","value":0.06,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows it in profile.","via":"harvest"}}]}}},{"subject":"magpul-mlok-polymer-rail-section-5-slot","title":"Magpul M-LOK® Polymer Rail, 5 Slots (MAG590)","dimensions":{"length":{"label":"Overall length (along the handguard)","kind":"length","measurements":[{"id":"page","value":2.5,"unit":"in","pm":0.05,"stated":"2.5\" 5-slot Picatinny rail segment easily attaches to any M-LOK mounting interface","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, M-LOK® Polymer Rail, 5 Slots (MAG590), Product Details","url":"https://magpul.com/m-lokpolymerrailsection-5slots.html","retrieved":"2026-10-29","via":"harvest"}},{"id":"gis","value":2.5,"unit":"in","pm":0.05,"stated":"MAG590 - 5 Slots, max overall length of 2.5”  NSN:1005016660494","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, M-LOK® Polymer Rail Sections GIS sheet (MAG589-MAG593), page 1","url":"https://magpul.com/media/wysiwyg/GIS/MAG589-MAG593_M-LOK_Polymer_Rail_Sections_GIS_01.pdf","retrieved":"2026-10-29","via":"harvest"}},{"id":"mgw","value":2.5,"unit":"in","pm":0.0625,"stated":"Product Length: 2-1/2\"","source":{"type":"spec","publisher":"retailer","name":"Midwest Gun Works, Magpul Polymer M-LOK Rail Section, 5 Slots (MAG590-BLK), Product Specifications","url":"https://www.midwestgunworks.com/page/mgwi/prod/mag590-blk","retrieved":"2026-10-29","via":"harvest"}},{"id":"pa","value":2.3,"unit":"in","pm":0.05,"stated":"5 slots with a maximum overall length of 2.3 inches","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Magpul Industries M-LOK Rail Section - 5 Slot, Features","url":"https://www.primaryarms.com/magpul-industries-m-lok-rail-section-5-slot","retrieved":"2026-10-29","via":"harvest"}},{"id":"studio","value":2.36,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-5-slot a01371f0ad8e (Magpul's mag590-blk_01, 1200 x 1200: the 5-slot alone on white, from above and in front, no screws in)","scaleRef":"its own rail slots at the standard's pitch (std.picatinny.slot_pitch, 0.394 in: Magpul's sheet, \"1913 Picatinny spec rail-mounted accessories\"): its five slots' lands, read by eye on the turned photo, 78.9 to 80.2 px apart","method":"the image turned 36.2 degrees so the part's long axis (its outline's principal axis) runs across; the outline's extent along it, 476 px at luminance under 170, over the pitch: 5.94 to 6.03 pitches; ± covers the pitch's reading and the ends' depth (an end's foot is a few hundredths of an inch off its top's line from this camera)","via":"harvest"}}],"adopt":{"from":"studio","reason":"Read on Magpul's own photo of this length, scaled by its own rail slots at the standard's pitch (std.picatinny.slot_pitch, 0.394 in: Magpul's sheet, \"1913 Picatinny spec rail-mounted accessories\"). Magpul's \"2.5\" is a maximum it states for the length in tenths, and every one of the five lengths, read the same way on its own photos, is its end-to-end rail slots (5 less one pitches) and 0.76 to 0.79 in more: 0.12 to 0.18 in under Magpul's figure from the 5-slot up (the 3-slot's 0.03). Drawn at Magpul's figure with the slots on the standard's pitch, its ends would be a tenth of an inch longer than any photo shows them; Magpul's own word is that the rail is the 1913 standard's. Primary Arms' 2.3 in agrees with the photo within its last digit."},"note":"The outline's two ends along the rail. Magpul gives a maximum, Midwest Gun Works Magpul's figure, Primary Arms 2.3 in; the photo is between, nearer Primary Arms'."},"height":{"label":"Height (its rail's top above the handguard's face it sits on)","kind":"length","measurements":[{"id":"assumed","value":0.33,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no photo of this length shows its side well enough to read. Magpul's studio photos of the 7-slot and the 9-slot, read the same way (the top flat's foreshortening against the standard's 0.656 in for the camera's elevation, the band below it for the side), give 0.316 and 0.345 in; Magpul's sheet and pages describe the five lengths as one moulding in five lengths. The ± covers both.","via":"harvest"}}],"note":"From the mounting face (the face that bears on the hand guard) to the rail's top."},"width":{"label":"Width (side to side, at its widest under the rail's head)","kind":"length","measurements":[{"id":"assumed","value":0.81,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view of this length square across it is on file. The 3-, 9- and 11-slot sections read 0.811, 0.816 and 0.79 in on their own top views; the ± covers them.","via":"harvest"}}],"note":"Its only view from above on file (c02432a0d57b, on a MOE hand guard) is taken from one side: its outline there takes in a side face, 0.86 in at its slots' scale. The rail's head is the standard's (0.835 in at its widest)."},"weight":{"label":"Weight (the moulding)","kind":"mass","measurements":[{"id":"model","value":0.279,"unit":"oz","pm":0.08,"source":{"type":"derived","basis":"The model's polymer volume, 0.4241 cubic inches (the manifest's body_volume_in3; the screws' heads apart), times std.density.polymer (Zytel nylon 66, 18.68 g, 0.659 oz to the cubic inch): 0.279 oz. Magpul names no grade (\"a proprietary reinforced composite\"): a glass-filled grade is up to a sixth heavier, the underside's pocket isn't drawn (the model is solid under its rail), and the height and the neck are readings or assumptions with their own ±; the ± takes all of them. The steel T-nuts and screws aren't in it.","via":"harvest"}}],"note":"Magpul states none. Worked out from the model (the weight's own entry says how)."},"rail_slots":{"label":"Rail slots","kind":"count","measurements":[{"id":"name","value":5,"unit":"count","stated":"M-LOK® Polymer Rail, 5 Slots","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, M-LOK® Polymer Rail, 5 Slots (MAG590), Product Details","url":"https://magpul.com/m-lokpolymerrailsection-5slots.html","retrieved":"2026-10-29","via":"harvest"}},{"id":"photo","value":5,"unit":"count","source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-5-slot a01371f0ad8e (Magpul's mag590-blk_01, 1200 x 1200: the 5-slot alone on white, from above and in front, no screws in)","scaleRef":"none: a count","method":"five slots between its two ends, a screw hole in the first and the fifth; four lands between the holes (the same on the top view on a MOE hand guard, c02432a0d57b, and on Magpul's sheet's photo of the five)","via":"harvest"}}],"adopt":{"from":"photo","reason":"Counted on the part; the name says the same."}},"rail_slot0_x":{"label":"Rear rail slot's centre ahead of the part's rear end","kind":"length","measurements":[{"id":"centred","value":0.392,"unit":"in","source":{"type":"derived","expr":"({.length} - ({.rail_slots} - 1) * {std.picatinny.slot_pitch}) / 2","via":"harvest"}}],"note":"Centred on its length, as its photos show it: the same distance from each end to the end slot's centre on the turned studio photo, within its reading."},"rear_hole_slot":{"label":"Rail slot its rear screw hole is in (counted from its rear end, the first is 1)","kind":"count","measurements":[{"id":"photo","value":1,"unit":"count","source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-5-slot a01371f0ad8e (Magpul's mag590-blk_01, 1200 x 1200: the 5-slot alone on white, from above and in front, no screws in)","scaleRef":"none: a count","method":"a screw hole in each end slot, four lands between them (the studio photo; the top view on a hand guard, c02432a0d57b, has its screws 206.7 px apart for 51.9 px a pitch: 3.98 pitches)","via":"harvest"}}]},"hole_pitches":{"label":"Rail slots from its rear screw hole to its front one (pitches)","kind":"count","measurements":[{"id":"photo","value":4,"unit":"count","source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-5-slot a01371f0ad8e (Magpul's mag590-blk_01, 1200 x 1200: the 5-slot alone on white, from above and in front, no screws in)","scaleRef":"none: a count","method":"a screw hole in each end slot, four lands between them (the studio photo; the top view on a hand guard, c02432a0d57b, has its screws 206.7 px apart for 51.9 px a pitch: 3.98 pitches)","via":"harvest"}}],"note":"Two screw holes, one in each end slot, four pitches apart (1.576 in): the M-LOK slot pitch (40 mm), so its two T-nuts go into two slots side by side. Under it, between the holes, one rectangular lug (its underside, e389e392fb30): Magpul's \"integral recoil lugs\"."},"lugs":{"label":"M-LOK slots its T-nuts span","kind":"count","measurements":[{"id":"holes","value":2,"unit":"count","source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-5-slot a01371f0ad8e (Magpul's mag590-blk_01, 1200 x 1200: the 5-slot alone on white, from above and in front, no screws in)","scaleRef":"none: a count","method":"its two screws four rail pitches apart (1.576 in, the M-LOK slot pitch): one T-nut in each of two slots","via":"harvest"}}],"note":"Two M-LOK slots: a T-nut in the rear half of each, the lug between them in the first slot's front half."},"lug_x":{"label":"Its seat on the M-LOK face: the centre of the M-LOK slot its rear T-nut is in, ahead of its rear end","kind":"length","measurements":[{"id":"rear-nut","value":0.7857,"unit":"in","source":{"type":"derived","expr":"{.rail_slot0_x} + ({.rear_hole_slot} - 1) * {std.picatinny.slot_pitch} + {std.mlok.interval} / 2","via":"harvest"}}],"note":"The rear screw hole is at its slot's centre (the photos), and its T-nut sits in the rear half of an M-LOK slot, half the M-LOK interval behind that slot's centre: what an M-LOK position places is that slot's centre. Two T-nuts the interval apart then sit one in each half of one slot (the 3-slot: the hand stop's seat); one a slot pitch further on sits in the rear half of the next. Magpul's page: \"Integral recoil lugs resist impact and keep rail secured under recoil and provide an intermediate spacing option\" (the lugs under it between its nuts, which go into a slot), and its M-LOK page: \"Your M-LOK accessory can be adjusted in 20mm increments (1/2 slot length)\". Which half of a slot a nut is in isn't published: the rear half is assumed."},"reach_inside":{"label":"Reach inside the handguard (below the mounting face, tightened)","kind":"length","measurements":[],"note":"Not published: Magpul gives no figure for its cammed T-nuts or for the recoil lugs under the section."},"neck_top_below_top":{"label":"Under the head: where its lower faces, carried on at 45 degrees past the lower gauge line, meet the neck, below the rail's top","kind":"length","measurements":[{"id":"assumed","value":0.2,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view of the part along its rail is on file, and the neck stands in the head's shadow in every photo. The head's lower faces are carried on at the standard's 45 degrees to here, as Midwest Industries' drop-in rail's are to theirs (0.204 in, read on its photo), so that what clamps a rail has room for its jaws under the head; the ± covers a neck from the standard's lower gauge width to two tenths narrower.","via":"harvest"}}],"note":"The head's lower faces are MIL-STD-1913's to its lower gauge line (std.picatinny.lower_gauge_below_top); under them the section narrows to a neck that leaves a clamp's jaws room under the head, then widens again to its width at a shoulder near the mounting face (neck_foot_above_face). With the standard's head (lib.rail_half) this sets the neck's half width."},"neck_foot_above_face":{"label":"Under the head: the neck's foot (the shoulder where the section widens to its width) above the mounting face","kind":"length","measurements":[{"id":"underside","value":0.055,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-5-slot e389e392fb30 (Magpul's mag590-feature_02, 700 x 525: the 5-slot's underside, its near long side toward the lens)","scaleRef":"the side face's height on the photo as the part's, 0.33 in less the head's top 0.0895 hidden from this lens (std.picatinny, the widest's top): about 30 px for 0.24 in across eight columns","method":"the image turned along the part (.cache/batch16, sideband.py); down each column the near side face reads as a lighter band at the mounting face's edge (5 to 10 px), a darker one (14 to 16 px: a face set back and shaded) and a lighter one at the silhouette (the head's lower faces); the first band's height at the second's scale: 0.04 to 0.074 in. Its 7-slot's underside (ae37b5337bea) shows the side as one band: no second reading","via":"harvest"}}]},"end_bevel_length":{"label":"Each end's slope, along the part: from the end to where its rail's top begins","kind":"length","measurements":[{"id":"studio","value":0.22,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-5-slot a01371f0ad8e (Magpul's mag590-blk_01, 1200 x 1200: the 5-slot alone on white, from above and in front, no screws in)","scaleRef":"the length's scale (200.3 px/in along the turned photo, its own slots)","method":"the sloped end (the M at the rear end) along the part, 44 px, read by eye on a 1.6-times enlargement","via":"harvest"}}],"note":"Magpul: \"The beveled ends reduce snagging and eliminate sharp corners and edges.\" The end face slopes and rounds down from the top to a short upright face at the mounting face (the photos from above and from the end)."},"end_face_height":{"label":"Each end's upright face under its slope, above the mounting face","kind":"length","measurements":[{"id":"assumed","value":0.08,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows it in profile.","via":"harvest"}}]},"end_corner_chamfer":{"label":"Each end's corners cut off in plan, along the end","kind":"length","measurements":[{"id":"assumed","value":0.13,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view of this length square from above shows its corners clearly. The 3-slot's top view has 0.13 in.","via":"harvest"}}]},"counterbore_diameter":{"label":"Each screw hole's recess, across","kind":"length","measurements":[{"id":"studio","value":0.39,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-5-slot a01371f0ad8e (Magpul's mag590-blk_01, 1200 x 1200: the 5-slot alone on white, from above and in front, no screws in)","scaleRef":"the length's scale (201.8 px/in along the turned photo, its own slots)","method":"the image turned along the part (as for the length); along the row through each hole's centre, the white of the hole (over 170 of 255) and the dark of the recess round it (under 85, past the hole's rim) (.cache/batch16, recess.py): 78 and 81 px, 0.387 and 0.401 in","via":"harvest"}}],"note":"A round recess round each screw hole, into the slot it is in and the lands either side of it (every photo of the part from above)."},"counterbore_floor":{"label":"The recess's floor above the mounting face (where the screw's head bears)","kind":"length","measurements":[{"id":"assumed","value":0.12,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows it in profile.","via":"harvest"}}]},"hole_diameter":{"label":"Screw hole, through","kind":"length","measurements":[{"id":"studio","value":0.2,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-5-slot a01371f0ad8e (Magpul's mag590-blk_01, 1200 x 1200: the 5-slot alone on white, from above and in front, no screws in)","scaleRef":"the length's scale (201.8 px/in along the turned photo)","method":"the image turned along the part (as for the length); along the row through each hole's centre, the white of the hole (over 170 of 255) and the dark of the recess round it (under 85, past the hole's rim) (.cache/batch16, recess.py): the white 40 and 42 px, 0.198 and 0.208 in","via":"harvest"}}]},"screw_head_diameter":{"label":"Screw's head, across","kind":"length","measurements":[{"id":"assumed","value":0.34,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: its head stands inside its recess in every photo of this length with its screws in, and none reads it apart from the recess. The 3-slot's top view has its head 0.034 in inside its recess's rim.","via":"harvest"}}],"note":"Its two screws are black socket button heads (Magpul's photo of the hardware under the 5- and 7-slot sections: two screws and two T-nuts)."},"screw_head_height":{"label":"Screw's head, from the recess's floor to its crown","kind":"length","measurements":[{"id":"assumed","value":0.06,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows it in profile.","via":"harvest"}}]}}},{"subject":"magpul-mlok-polymer-rail-section-7-slot","title":"Magpul M-LOK® Polymer Rail, 7 Slots (MAG591)","dimensions":{"length":{"label":"Overall length (along the handguard)","kind":"length","measurements":[{"id":"page","value":3.3,"unit":"in","pm":0.05,"stated":"3.3\" 7-slot Picatinny rail segment easily attaches to any M-LOK mounting interface","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, M-LOK® Polymer Rail, 7 Slots (MAG591), Product Details","url":"https://magpul.com/m-lokpolymerrailsection-7slots.html","retrieved":"2026-10-29","via":"harvest"}},{"id":"gis","value":3.3,"unit":"in","pm":0.05,"stated":"MAG591 - 7 Slots, max overall length of 3.3”  NSN:1005016659435","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, M-LOK® Polymer Rail Sections GIS sheet (MAG589-MAG593), page 1","url":"https://magpul.com/media/wysiwyg/GIS/MAG589-MAG593_M-LOK_Polymer_Rail_Sections_GIS_01.pdf","retrieved":"2026-10-29","via":"harvest"}},{"id":"ar15discounts","value":3.3,"unit":"in","pm":0.05,"stated":"Weight 0.64 oz Dimensions 3.3 × 0.8 × 0.5 in","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, MAGPUL M-LOK Poly Rail Section - 7 slots, Additional information","url":"https://ar15discounts.com/products/magpul-m-lok-poly-rail-section-7-slots/","retrieved":"2026-10-29","via":"harvest"}},{"id":"studio","value":3.147,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-7-slot f5d2876e177a (Magpul's mag591-blk_01, 1200 x 1200: the 7-slot alone on white, from above and in front, no screws in)","scaleRef":"its own rail slots at the standard's pitch (std.picatinny.slot_pitch, 0.394 in: Magpul's sheet, \"1913 Picatinny spec rail-mounted accessories\"): the seven lands' rear edges, read on the turned photo, 92.9 px apart ((895 - 170) / 6 on a 1.3-times enlargement)","method":"the image turned 27.6 degrees so the part's long axis (its outline's principal axis) runs across; the outline's extent along it, 742 px at luminance under 170: 7.99 pitches; ± covers the pitch's reading and the ends' depth","via":"harvest"}}],"adopt":{"from":"studio","reason":"Read on Magpul's own photo of this length, scaled by its own rail slots at the standard's pitch (std.picatinny.slot_pitch, 0.394 in: Magpul's sheet, \"1913 Picatinny spec rail-mounted accessories\"). Magpul's \"3.3\" is a maximum it states for the length in tenths, and every one of the five lengths, read the same way on its own photos, is its end-to-end rail slots (7 less one pitches) and 0.76 to 0.79 in more: 0.12 to 0.18 in under Magpul's figure from the 5-slot up (the 3-slot's 0.03). Drawn at Magpul's figure with the slots on the standard's pitch, its ends would be a tenth of an inch longer than any photo shows them; Magpul's own word is that the rail is the 1913 standard's. The seller's 3.3 is Magpul's figure."},"note":"The outline's two ends along the rail."},"height":{"label":"Height (its rail's top above the handguard's face it sits on)","kind":"length","measurements":[{"id":"studio","value":0.316,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-7-slot f5d2876e177a (Magpul's mag591-blk_01, 1200 x 1200: the 7-slot alone on white, from above and in front, no screws in)","scaleRef":"the length's scale along the part (235.8 px/in, its own slots)","method":"down four columns through lands of the turned photo: the top's flat from the highlight on its far edge to where it darkens at its near edge, 142 to 144 px, against the standard's 0.656 in flat (std.picatinny) gives the camera's elevation, 66.6 to 68.6 degrees; the band below it to the outline's near edge, 30 to 32 px, is the near upper face, the widest and the side face down to the mounting face seen at that elevation (the head's figures as lib.rail_head draws them): 0.306 to 0.327 in, mean 0.316 (.cache/batch16, height.py); ± covers the elevation's reading","via":"harvest"}},{"id":"ar15discounts","value":0.5,"unit":"in","pm":0.05,"stated":"Weight 0.64 oz Dimensions 3.3 × 0.8 × 0.5 in","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, MAGPUL M-LOK Poly Rail Section - 7 slots, Additional information","url":"https://ar15discounts.com/products/magpul-m-lok-poly-rail-section-7-slots/","retrieved":"2026-10-29","via":"harvest"}}],"adopt":{"from":"studio","reason":"Read on Magpul's own photo of the part. The seller's \"3.3 × 0.8 × 0.5 in\" is its listing's shipping fields (its 3.3 is Magpul's maximum length, rounded the same way), and a rail section half an inch tall would show its side as a band twice as wide as the photo has."},"note":"From the mounting face (the face that bears on the hand guard) to the rail's top."},"width":{"label":"Width (side to side, at its widest under the rail's head)","kind":"length","measurements":[{"id":"ar15discounts","value":0.8,"unit":"in","pm":0.05,"stated":"Weight 0.64 oz Dimensions 3.3 × 0.8 × 0.5 in","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, MAGPUL M-LOK Poly Rail Section - 7 slots, Additional information","url":"https://ar15discounts.com/products/magpul-m-lok-poly-rail-section-7-slots/","retrieved":"2026-10-29","via":"harvest"}}],"note":"A seller's figure. The 3-, 9- and 11-slot sections read 0.811, 0.816 and 0.79 on their own top views; the rail's head is the standard's (0.835 in at its widest)."},"weight":{"label":"Weight (the moulding)","kind":"mass","measurements":[{"id":"model","value":0.37,"unit":"oz","pm":0.11,"source":{"type":"derived","basis":"The model's polymer volume, 0.5608 cubic inches (the manifest's body_volume_in3; the screws' heads apart), times std.density.polymer (Zytel nylon 66, 18.68 g, 0.659 oz to the cubic inch): 0.37 oz. Magpul names no grade (\"a proprietary reinforced composite\"): a glass-filled grade is up to a sixth heavier, the underside's pocket isn't drawn (the model is solid under its rail), and the height and the neck are readings or assumptions with their own ±; the ± takes all of them. The steel T-nuts and screws aren't in it.","via":"harvest"}},{"id":"ar15discounts","value":0.64,"unit":"oz","pm":0.005,"stated":"Weight 0.64 oz Dimensions 3.3 × 0.8 × 0.5 in","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, MAGPUL M-LOK Poly Rail Section - 7 slots, Additional information","url":"https://ar15discounts.com/products/magpul-m-lok-poly-rail-section-7-slots/","retrieved":"2026-10-29","via":"harvest"}}],"adopt":{"from":"model","reason":"The seller's figures are its listing's shipping fields: its 3.3 in is Magpul's maximum length and its 0.5 in a height no photo of the part allows (the height's own entry). Its 0.64 oz may be the section with its two steel screws and T-nuts; the model's polymer is the section alone, as the build draws it."},"note":"Magpul states none. Worked out from the model, as the other lengths' are; a seller's listing gives 0.64 oz, kept beside it (the adoption says why)."},"rail_slots":{"label":"Rail slots","kind":"count","measurements":[{"id":"name","value":7,"unit":"count","stated":"M-LOK® Polymer Rail, 7 Slots","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, M-LOK® Polymer Rail, 7 Slots (MAG591), Product Details","url":"https://magpul.com/m-lokpolymerrailsection-7slots.html","retrieved":"2026-10-29","via":"harvest"}},{"id":"photo","value":7,"unit":"count","source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-7-slot f5d2876e177a (Magpul's mag591-blk_01, 1200 x 1200: the 7-slot alone on white, from above and in front, no screws in)","scaleRef":"none: a count","method":"seven slots between its two ends, a screw hole in the first and the seventh; six lands between the holes (the same on its installed photo, 93a82746006a)","via":"harvest"}}],"adopt":{"from":"photo","reason":"Counted on the part; the name says the same."}},"rail_slot0_x":{"label":"Rear rail slot's centre ahead of the part's rear end","kind":"length","measurements":[{"id":"centred","value":0.3915,"unit":"in","source":{"type":"derived","expr":"({.length} - ({.rail_slots} - 1) * {std.picatinny.slot_pitch}) / 2","via":"harvest"}}],"note":"Centred on its length, as its photos show it."},"rear_hole_slot":{"label":"Rail slot its rear screw hole is in (counted from its rear end, the first is 1)","kind":"count","measurements":[{"id":"photo","value":1,"unit":"count","source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-7-slot f5d2876e177a (Magpul's mag591-blk_01, 1200 x 1200: the 7-slot alone on white, from above and in front, no screws in)","scaleRef":"none: a count","method":"a screw hole in each end slot, six lands between them (the studio photo and the installed one)","via":"harvest"}}]},"hole_pitches":{"label":"Rail slots from its rear screw hole to its front one (pitches)","kind":"count","measurements":[{"id":"photo","value":6,"unit":"count","source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-7-slot f5d2876e177a (Magpul's mag591-blk_01, 1200 x 1200: the 7-slot alone on white, from above and in front, no screws in)","scaleRef":"none: a count","method":"a screw hole in each end slot, six lands between them (the studio photo and the installed one)","via":"harvest"}}],"note":"Two screw holes, one in each end slot, six pitches apart (2.364 in): one and a half M-LOK slot pitches, so one T-nut in the rear half of a slot and the other in the front half of the next. Under it, between the holes, two rectangular lugs (its underside, ae37b5337bea): Magpul's \"integral recoil lugs\"."},"lugs":{"label":"M-LOK slots its T-nuts span","kind":"count","measurements":[{"id":"holes","value":2,"unit":"count","source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-7-slot f5d2876e177a (Magpul's mag591-blk_01, 1200 x 1200: the 7-slot alone on white, from above and in front, no screws in)","scaleRef":"none: a count","method":"its two screws six rail pitches apart (2.364 in, 60 mm): one T-nut in the rear half of a slot, the other in the front half of the next","via":"harvest"}}],"note":"Two M-LOK slots."},"lug_x":{"label":"Its seat on the M-LOK face: the centre of the M-LOK slot its rear T-nut is in, ahead of its rear end","kind":"length","measurements":[{"id":"rear-nut","value":0.7852,"unit":"in","source":{"type":"derived","expr":"{.rail_slot0_x} + ({.rear_hole_slot} - 1) * {std.picatinny.slot_pitch} + {std.mlok.interval} / 2","via":"harvest"}}],"note":"The rear screw hole is at its slot's centre (the photos), and its T-nut sits in the rear half of an M-LOK slot, half the M-LOK interval behind that slot's centre: what an M-LOK position places is that slot's centre. Two T-nuts the interval apart then sit one in each half of one slot (the 3-slot: the hand stop's seat); one a slot pitch further on sits in the rear half of the next. Magpul's page: \"Integral recoil lugs resist impact and keep rail secured under recoil and provide an intermediate spacing option\" (the lugs under it between its nuts, which go into a slot), and its M-LOK page: \"Your M-LOK accessory can be adjusted in 20mm increments (1/2 slot length)\". Which half of a slot a nut is in isn't published: the rear half is assumed."},"reach_inside":{"label":"Reach inside the handguard (below the mounting face, tightened)","kind":"length","measurements":[],"note":"Not published: Magpul gives no figure for its cammed T-nuts or for the recoil lugs under the section."},"neck_top_below_top":{"label":"Under the head: where its lower faces, carried on at 45 degrees past the lower gauge line, meet the neck, below the rail's top","kind":"length","measurements":[{"id":"assumed","value":0.2,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view of the part along its rail is on file, and the neck stands in the head's shadow in every photo. The head's lower faces are carried on at the standard's 45 degrees to here, as Midwest Industries' drop-in rail's are to theirs (0.204 in, read on its photo), so that what clamps a rail has room for its jaws under the head; the ± covers a neck from the standard's lower gauge width to two tenths narrower.","via":"harvest"}}],"note":"The head's lower faces are MIL-STD-1913's to its lower gauge line (std.picatinny.lower_gauge_below_top); under them the section narrows to a neck that leaves a clamp's jaws room under the head, then widens again to its width at a shoulder near the mounting face (neck_foot_above_face). With the standard's head (lib.rail_half) this sets the neck's half width."},"neck_foot_above_face":{"label":"Under the head: the neck's foot (the shoulder where the section widens to its width) above the mounting face","kind":"length","measurements":[{"id":"assumed","value":0.055,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no photo of this length's side shows its shoulder. The 5-slot's underside photo (e389e392fb30) reads 0.055 in; the ± covers it.","via":"harvest"}}]},"end_bevel_length":{"label":"Each end's slope, along the part: from the end to where its rail's top begins","kind":"length","measurements":[{"id":"studio","value":0.163,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-7-slot f5d2876e177a (Magpul's mag591-blk_01, 1200 x 1200: the 7-slot alone on white, from above and in front, no screws in)","scaleRef":"the length's scale (235.8 px/in along the turned photo)","method":"the sloped end (the M at the rear end) along the part, 38.5 px, read by eye on a 1.3-times enlargement","via":"harvest"}}],"note":"Magpul: \"The beveled ends reduce snagging and eliminate sharp corners and edges.\" The end face slopes and rounds down from the top to a short upright face at the mounting face (the photos from above and from the end)."},"end_face_height":{"label":"Each end's upright face under its slope, above the mounting face","kind":"length","measurements":[{"id":"assumed","value":0.08,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows it in profile.","via":"harvest"}}]},"end_corner_chamfer":{"label":"Each end's corners cut off in plan, along the end","kind":"length","measurements":[{"id":"assumed","value":0.13,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view of this length square from above is on file. The 3-slot's top view has 0.13 in.","via":"harvest"}}]},"counterbore_diameter":{"label":"Each screw hole's recess, across","kind":"length","measurements":[{"id":"studio","value":0.37,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-7-slot f5d2876e177a (Magpul's mag591-blk_01, 1200 x 1200: the 7-slot alone on white, from above and in front, no screws in)","scaleRef":"the length's scale (235.8 px/in along the turned photo, its own slots)","method":"the image turned along the part (as for the length); along the row through each hole's centre, the white of the hole (over 170 of 255) and the dark of the recess round it (under 85, past the hole's rim) (.cache/batch16, recess.py): 84 and 89 px, 0.356 and 0.377 in; by eye on the enlargement it reads 0.41, which the ± takes in","via":"harvest"}}],"note":"A round recess round each screw hole, into the slot it is in and the lands either side of it (every photo of the part from above)."},"counterbore_floor":{"label":"The recess's floor above the mounting face (where the screw's head bears)","kind":"length","measurements":[{"id":"assumed","value":0.12,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows it in profile.","via":"harvest"}}]},"hole_diameter":{"label":"Screw hole, through","kind":"length","measurements":[{"id":"studio","value":0.2,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-7-slot f5d2876e177a (Magpul's mag591-blk_01, 1200 x 1200: the 7-slot alone on white, from above and in front, no screws in)","scaleRef":"the length's scale (235.8 px/in along the turned photo)","method":"the image turned along the part (as for the length); along the row through each hole's centre, the white of the hole (over 170 of 255) and the dark of the recess round it (under 85, past the hole's rim) (.cache/batch16, recess.py): the white 44 and 50 px, 0.187 and 0.212 in","via":"harvest"}}]},"screw_head_diameter":{"label":"Screw's head, across","kind":"length","measurements":[{"id":"assumed","value":0.34,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: its head stands inside its recess in every photo of this length with its screws in, and none reads it apart from the recess. The 3-slot's top view has its head 0.034 in inside its recess's rim.","via":"harvest"}}],"note":"Its two screws are black socket button heads (Magpul's photo of the hardware under the 5- and 7-slot sections: two screws and two T-nuts)."},"screw_head_height":{"label":"Screw's head, from the recess's floor to its crown","kind":"length","measurements":[{"id":"assumed","value":0.06,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows it in profile.","via":"harvest"}}]}}},{"subject":"magpul-mlok-polymer-rail-section-9-slot","title":"Magpul M-LOK® Polymer Rail, 9 Slots (MAG592)","dimensions":{"length":{"label":"Overall length (along the handguard)","kind":"length","measurements":[{"id":"page","value":4.1,"unit":"in","pm":0.05,"stated":"4.1\" 9-slot Picatinny rail segment easily attaches to any M-LOK mounting interface","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, M-LOK® Polymer Rail, 9 Slots (MAG592), Product Details","url":"https://magpul.com/m-lokpolymerrailsection-9slots.html","retrieved":"2026-10-29","via":"harvest"}},{"id":"studio","value":3.912,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-9-slot 79190f958b5c (Magpul's mag592-blk_01, 1200 x 1200: the 9-slot alone on white, from above and in front, no screws in)","scaleRef":"its own rail slots at the standard's pitch (std.picatinny.slot_pitch, 0.394 in: Magpul's sheet, \"1913 Picatinny spec rail-mounted accessories\"): its lands' rear edges, read on the turned photo, 77.9 px apart ((655 - 110) / 7)","method":"the image turned 36.4 degrees so the part's long axis (its outline's principal axis) runs across; the outline's extent along it, 773 px at luminance under 170: 9.93 pitches; ± covers the pitch's reading and the ends' depth","via":"harvest"}}],"adopt":{"from":"studio","reason":"Read on Magpul's own photo of this length, scaled by its own rail slots at the standard's pitch (std.picatinny.slot_pitch, 0.394 in: Magpul's sheet, \"1913 Picatinny spec rail-mounted accessories\"). Magpul's \"4.1\" is a maximum it states for the length in tenths, and every one of the five lengths, read the same way on its own photos, is its end-to-end rail slots (9 less one pitches) and 0.76 to 0.79 in more: 0.12 to 0.18 in under Magpul's figure from the 5-slot up (the 3-slot's 0.03). Drawn at Magpul's figure with the slots on the standard's pitch, its ends would be a tenth of an inch longer than any photo shows them; Magpul's own word is that the rail is the 1913 standard's."},"note":"The outline's two ends along the rail."},"height":{"label":"Height (its rail's top above the handguard's face it sits on)","kind":"length","measurements":[{"id":"studio","value":0.345,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-9-slot 79190f958b5c (Magpul's mag592-blk_01, 1200 x 1200: the 9-slot alone on white, from above and in front, no screws in)","scaleRef":"the length's scale along the part (197.6 px/in, its own slots)","method":"down four columns through lands of the turned photo, as the 7-slot's (.cache/batch16, height.py): the top's flat against the standard's 0.656 in for the camera's elevation (64.5 to 74.6 degrees), the band below it for the side: 0.287, 0.332, 0.369 and 0.391 in, mean 0.345; a fifth column, through a hole, read nothing; ± covers their spread","via":"harvest"}}],"note":"From the mounting face (the face that bears on the hand guard) to the rail's top."},"width":{"label":"Width (side to side, at its widest under the rail's head)","kind":"length","measurements":[{"id":"top-view","value":0.816,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-9-slot 8c75c935d56b (Magpul's mag592-feature_01, 700 x 525: the 9-slot on a hand guard's side face, three screws in, seen square on)","scaleRef":"its three screws, 98.5 px apart, taken as four rail pitches each (its holes are in the first, the fifth and the ninth slots): 62.5 px/in","method":"its outline across a column band through its middle (columns 290 to 330): from its top edge, row 244, to the hand guard's opening beside its lower edge, row 295: 51 px; ± covers 2 px at each edge","via":"harvest"}}],"note":"Across, square on. The rail's head is the standard's (0.835 in at its widest)."},"weight":{"label":"Weight (the moulding)","kind":"mass","measurements":[{"id":"model","value":0.488,"unit":"oz","pm":0.15,"source":{"type":"derived","basis":"The model's polymer volume, 0.74 cubic inches (the manifest's body_volume_in3; the screws' heads apart), times std.density.polymer (Zytel nylon 66, 18.68 g, 0.659 oz to the cubic inch): 0.488 oz. Magpul names no grade (\"a proprietary reinforced composite\"): a glass-filled grade is up to a sixth heavier, the underside's pocket isn't drawn (the model is solid under its rail), and the height and the neck are readings or assumptions with their own ±; the ± takes all of them. The steel T-nuts and screws aren't in it.","via":"harvest"}}],"note":"Magpul states none. Worked out from the model (the weight's own entry says how)."},"rail_slots":{"label":"Rail slots","kind":"count","measurements":[{"id":"name","value":9,"unit":"count","stated":"M-LOK® Polymer Rail, 9 Slots","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, M-LOK® Polymer Rail, 9 Slots (MAG592), Product Details","url":"https://magpul.com/m-lokpolymerrailsection-9slots.html","retrieved":"2026-10-29","via":"harvest"}},{"id":"photo","value":9,"unit":"count","source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-9-slot 79190f958b5c (Magpul's mag592-blk_01, 1200 x 1200: the 9-slot alone on white, from above and in front, no screws in)","scaleRef":"none: a count","method":"nine slots between its two ends, a screw hole in the first, the fifth and the ninth (the same on its square view on a hand guard, 8c75c935d56b, three screws in)","via":"harvest"}}],"adopt":{"from":"photo","reason":"Counted on the part; the name says the same."}},"rail_slot0_x":{"label":"Rear rail slot's centre ahead of the part's rear end","kind":"length","measurements":[{"id":"centred","value":0.38,"unit":"in","source":{"type":"derived","expr":"({.length} - ({.rail_slots} - 1) * {std.picatinny.slot_pitch}) / 2","via":"harvest"}}],"note":"Centred on its length, as its photos show it."},"rear_hole_slot":{"label":"Rail slot its rear screw hole is in (counted from its rear end, the first is 1)","kind":"count","measurements":[{"id":"photo","value":1,"unit":"count","source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-9-slot 79190f958b5c (Magpul's mag592-blk_01, 1200 x 1200: the 9-slot alone on white, from above and in front, no screws in)","scaleRef":"none: a count","method":"screw holes in the first, the fifth and the ninth slots: three lands between each two (the studio photo; its square view on a hand guard has its three screws 98.5 px apart, the hand guard's M-LOK openings beside it at the same spacing)","via":"harvest"}}]},"hole_pitches":{"label":"Rail slots from its rear screw hole to its front one (pitches)","kind":"count","measurements":[{"id":"photo","value":8,"unit":"count","source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-9-slot 79190f958b5c (Magpul's mag592-blk_01, 1200 x 1200: the 9-slot alone on white, from above and in front, no screws in)","scaleRef":"none: a count","method":"screw holes in the first, the fifth and the ninth slots: three lands between each two (the studio photo; its square view on a hand guard has its three screws 98.5 px apart, the hand guard's M-LOK openings beside it at the same spacing)","via":"harvest"}}],"note":"Three screw holes, in the first, the fifth and the ninth slots, four pitches (40 mm, an M-LOK slot pitch) apart: the two end holes eight pitches apart (3.152 in, 80 mm). The model draws a screw in each end hole."},"middle_hole_pitches":{"label":"Rail slots from its rear screw hole to its middle one (pitches)","kind":"count","measurements":[{"id":"photo","value":4,"unit":"count","source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-9-slot 79190f958b5c (Magpul's mag592-blk_01, 1200 x 1200: the 9-slot alone on white, from above and in front, no screws in)","scaleRef":"none: a count","method":"screw holes in the first, the fifth and the ninth slots: three lands between each two (the studio photo; its square view on a hand guard has its three screws 98.5 px apart, the hand guard's M-LOK openings beside it at the same spacing)","via":"harvest"}}],"note":"The middle hole is the 'intermediate spacing option' of Magpul's sheet, as far as the photos show: two screws come with it (sellers' words), and any two of the three holes take them."},"lugs":{"label":"M-LOK slots its T-nuts span","kind":"count","measurements":[{"id":"holes","value":3,"unit":"count","source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-9-slot 79190f958b5c (Magpul's mag592-blk_01, 1200 x 1200: the 9-slot alone on white, from above and in front, no screws in)","scaleRef":"none: a count","method":"its end screws eight rail pitches apart (3.152 in, 80 mm): a T-nut in the rear half of one slot and the other in the rear half of the slot two on","via":"harvest"}}],"note":"Three M-LOK slots, with screws in its two end holes."},"lug_x":{"label":"Its seat on the M-LOK face: the centre of the M-LOK slot its rear T-nut is in, ahead of its rear end","kind":"length","measurements":[{"id":"rear-nut","value":0.7737,"unit":"in","source":{"type":"derived","expr":"{.rail_slot0_x} + ({.rear_hole_slot} - 1) * {std.picatinny.slot_pitch} + {std.mlok.interval} / 2","via":"harvest"}}],"note":"The rear screw hole is at its slot's centre (the photos), and its T-nut sits in the rear half of an M-LOK slot, half the M-LOK interval behind that slot's centre: what an M-LOK position places is that slot's centre. Two T-nuts the interval apart then sit one in each half of one slot (the 3-slot: the hand stop's seat); one a slot pitch further on sits in the rear half of the next. Magpul's page: \"Integral recoil lugs resist impact and keep rail secured under recoil and provide an intermediate spacing option\" (the lugs under it between its nuts, which go into a slot), and its M-LOK page: \"Your M-LOK accessory can be adjusted in 20mm increments (1/2 slot length)\". Which half of a slot a nut is in isn't published: the rear half is assumed."},"reach_inside":{"label":"Reach inside the handguard (below the mounting face, tightened)","kind":"length","measurements":[],"note":"Not published: Magpul gives no figure for its cammed T-nuts or for the recoil lugs under the section."},"neck_top_below_top":{"label":"Under the head: where its lower faces, carried on at 45 degrees past the lower gauge line, meet the neck, below the rail's top","kind":"length","measurements":[{"id":"assumed","value":0.2,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view of the part along its rail is on file, and the neck stands in the head's shadow in every photo. The head's lower faces are carried on at the standard's 45 degrees to here, as Midwest Industries' drop-in rail's are to theirs (0.204 in, read on its photo), so that what clamps a rail has room for its jaws under the head; the ± covers a neck from the standard's lower gauge width to two tenths narrower.","via":"harvest"}}],"note":"The head's lower faces are MIL-STD-1913's to its lower gauge line (std.picatinny.lower_gauge_below_top); under them the section narrows to a neck that leaves a clamp's jaws room under the head, then widens again to its width at a shoulder near the mounting face (neck_foot_above_face). With the standard's head (lib.rail_half) this sets the neck's half width."},"neck_foot_above_face":{"label":"Under the head: the neck's foot (the shoulder where the section widens to its width) above the mounting face","kind":"length","measurements":[{"id":"assumed","value":0.055,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no photo of this length's side shows its shoulder. The 5-slot's underside photo (e389e392fb30) reads 0.055 in; the ± covers it.","via":"harvest"}}]},"end_bevel_length":{"label":"Each end's slope, along the part: from the end to where its rail's top begins","kind":"length","measurements":[{"id":"studio","value":0.2,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-9-slot 79190f958b5c (Magpul's mag592-blk_01, 1200 x 1200: the 9-slot alone on white, from above and in front, no screws in)","scaleRef":"the length's scale (197.6 px/in along the turned photo)","method":"the sloped end (the M at the rear end) along the part, about 40 px, by eye","via":"harvest"}}],"note":"Magpul: \"The beveled ends reduce snagging and eliminate sharp corners and edges.\" The end face slopes and rounds down from the top to a short upright face at the mounting face (the photos from above and from the end)."},"end_face_height":{"label":"Each end's upright face under its slope, above the mounting face","kind":"length","measurements":[{"id":"assumed","value":0.08,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows it in profile.","via":"harvest"}}]},"end_corner_chamfer":{"label":"Each end's corners cut off in plan, along the end","kind":"length","measurements":[{"id":"assumed","value":0.13,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view of this length square from above shows its corners clearly. The 3-slot's top view has 0.13 in.","via":"harvest"}}]},"counterbore_diameter":{"label":"Each screw hole's recess, across","kind":"length","measurements":[{"id":"top-view","value":0.4,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-9-slot 8c75c935d56b (Magpul's mag592-feature_01, 700 x 525: the 9-slot on a hand guard's side face, three screws in, seen square on)","scaleRef":"its screws' spacing as four pitches (62.5 px/in)","method":"the dark round each screw's head stands in, about 25 px across, by eye (on the studio photo the recesses' dark runs into the slots' shadows: 0.33 to 0.55 in, not read)","via":"harvest"}}],"note":"A round recess round each screw hole, into the slot it is in and the lands either side of it (every photo of the part from above)."},"counterbore_floor":{"label":"The recess's floor above the mounting face (where the screw's head bears)","kind":"length","measurements":[{"id":"assumed","value":0.12,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows it in profile.","via":"harvest"}}]},"hole_diameter":{"label":"Screw hole, through","kind":"length","measurements":[{"id":"studio","value":0.21,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-mlok-polymer-rail-section-9-slot 79190f958b5c (Magpul's mag592-blk_01, 1200 x 1200: the 9-slot alone on white, from above and in front, no screws in)","scaleRef":"the length's scale (197.6 px/in along the turned photo, its own slots)","method":"the image turned along the part (as for the length); along the row through each hole's centre, the white of the hole (over 170 of 255) and the dark of the recess round it (under 85, past the hole's rim) (.cache/batch16, recess.py): the white of its three holes 40, 43 and 41 px, 0.202, 0.218 and 0.207 in","via":"harvest"}}]},"screw_head_diameter":{"label":"Screw's head, across","kind":"length","measurements":[{"id":"assumed","value":0.34,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: its head stands inside its recess in every photo of this length with its screws in, and none reads it apart from the recess. The 3-slot's top view has its head 0.034 in inside its recess's rim.","via":"harvest"}}],"note":"Its two screws are black socket button heads (Magpul's photo of the hardware under the 5- and 7-slot sections: two screws and two T-nuts)."},"screw_head_height":{"label":"Screw's head, from the recess's floor to its crown","kind":"length","measurements":[{"id":"assumed","value":0.06,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows it in profile.","via":"harvest"}}]}}},{"subject":"magpul-mlok-qd-sling-mount","title":"Magpul M-LOK QD Sling Mount (MAG606)","dimensions":{"length":{"label":"Overall length (along the handguard)","kind":"length","measurements":[{"id":"magpul","value":1.3,"unit":"in","pm":0.05,"stated":"Length, Max: 1.3 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, M-LOK QD Sling Mount (MAG606), Technical Specifications","url":"https://magpul.com/m-lok-qd-sling-mount.html","retrieved":"2026-10-05","via":"harvest"}},{"id":"wing","value":1.29,"unit":"in","stated":"Length: 1.29\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Magpul M-LOK QD Sling Attachment (MAG-606-BLK), Specifications (its own labels: Height, Length, Thickness; source of the figures unstated)","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/handguards-rails/rail-system-parts-accessories/magpul-m-lok-qd-sling-attachment/","retrieved":"2026-10-05","via":"harvest"}},{"id":"primary-arms","value":1.3,"unit":"in","pm":0.05,"stated":"Length: 1.3\"","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Magpul M-LOK QD Sling Mount (SKU MAG606, MPN MAG606-BLK), Features","url":"https://www.primaryarms.com/magpul-m-lok-qd-sling-mount-mag606","retrieved":"2026-10-05","via":"harvest"}},{"id":"midwest","value":1.3,"unit":"in","pm":0.05,"stated":"Length, Max: 1.3 in..","source":{"type":"spec","publisher":"retailer","name":"Midwest Gun Works, Magpul M-LOK QD Sling Mount (MAG606), Specifications","url":"https://www.midwestgunworks.com/page/mgwi/prod/MAG606","retrieved":"2026-10-05","via":"harvest"}},{"id":"scheels","value":1.3,"unit":"in","pm":0.05,"stated":"Max Length: 1.3 in.","source":{"type":"spec","publisher":"retailer","name":"Scheels, Magpul M-LOK QD Sling Mount (873750-MAG606), Specifications","url":"https://www.scheels.com/p/magpul-m-lok-qd-sling-mount/873750-MAG606/","retrieved":"2026-10-05","via":"harvest"}},{"id":"alexanders","value":1.3,"unit":"in","pm":0.05,"stated":"Length: 1.3 in","source":{"type":"spec","publisher":"retailer","name":"Alexander's Store, Magpul M-LOK QD Sling Mount - Forward Attachment (MAG606-BLK)","url":"https://alexandersstore.com/product/magpul-m-lok-qd-sling-mnt/","retrieved":"2026-10-05","via":"harvest"}},{"id":"dirty-bird","value":1.3,"unit":"in","pm":0.05,"stated":"Length: 1.3”","source":{"type":"spec","publisher":"retailer","name":"Dirty Bird, Magpul M-LOK QD Sling Mount - MPIMAG606","url":"https://dirtybirdusa.com/products/magpul-m-lok-qd-sling-mount/","retrieved":"2026-10-05","via":"harvest"}},{"id":"ar15discounts","value":1.3,"unit":"in","pm":0.05,"stated":"Length: 1.3”","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, Magpul M-LOK QD Sling Mount - MPIMAG606 (the same listing as Dirty Bird's)","url":"https://ar15discounts.com/products/magpul-m-lok-qd-sling-mount/","retrieved":"2026-10-05","via":"harvest"}},{"id":"patent-screws","value":1.321,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-mlok-qd-sling-mount 984ec513ef51 (US D746,404 S (Magpul, 'Firearm quick detach mount for a sling'), FIG. 3 front elevation (the outer face), 300 dpi)","scaleRef":"frame from the reviewed holes rear, front (1186.6 px/in, rms 0.000 in over 2 points): the two screw holes' centres, 934.4 px apart, as std.mlok.interval (20 mm)","method":"width of the traced outline (tools/trace.py); the plan outline's length at the scale of its own two screw holes, taken as the M-LOK interval apart: 1568 px between the end strokes' middles. The reading is good to 0.003 (the ends' strokes, the holes' centres); the ± also covers how true a design patent's drawing is to the product (the catalog's other Magpul patents read within 0.6% of Magpul's figures, the K2+'s 13% over one way)","via":"harvest"}}],"adopt":{"from":"patent-screws","reason":"The scale every outline is drawn to. Finer than the maker's one decimal and inside it; at it the drawing's width reads the maker's 0.6 (0.601) and its height 0.35, the maker's 0.4 to one decimal, which no scale under 1.31 long gives; and Magpul's own photo of the mount seen square on (gallery _05) has its screws 0.595 of its length apart, the drawing's 0.596. Wing Tactical's 1.29 is the one figure it doesn't meet."},"note":"Magpul prints one decimal. The drawing at the M-LOK interval's scale reads 1.32, inside it, and is what the outline is drawn to; Wing Tactical's 1.29 is 0.03 short of that and outside the two ± together: kept, not adopted (the header)."},"height":{"label":"Height (how far it stands off the handguard's face)","kind":"length","measurements":[{"id":"magpul","value":0.4,"unit":"in","pm":0.05,"stated":"Height, from surface of Hand Guard: 0.4 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, M-LOK QD Sling Mount (MAG606), Technical Specifications","url":"https://magpul.com/m-lok-qd-sling-mount.html","retrieved":"2026-10-05","via":"harvest"}},{"id":"wing","value":0.3,"unit":"in","pm":0.05,"stated":"Thickness: 0.3\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Magpul M-LOK QD Sling Attachment (MAG-606-BLK), Specifications (its own labels: Height, Length, Thickness; source of the figures unstated)","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/handguards-rails/rail-system-parts-accessories/magpul-m-lok-qd-sling-attachment/","retrieved":"2026-10-05","via":"harvest"}},{"id":"primary-arms","value":0.4,"unit":"in","pm":0.05,"stated":"Height: 0.4\"","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Magpul M-LOK QD Sling Mount (SKU MAG606, MPN MAG606-BLK), Features","url":"https://www.primaryarms.com/magpul-m-lok-qd-sling-mount-mag606","retrieved":"2026-10-05","via":"harvest"}},{"id":"midwest","value":0.4,"unit":"in","pm":0.05,"stated":"Height, From Surface of Hand Guard: 0.4 in","source":{"type":"spec","publisher":"retailer","name":"Midwest Gun Works, Magpul M-LOK QD Sling Mount (MAG606), Specifications","url":"https://www.midwestgunworks.com/page/mgwi/prod/MAG606","retrieved":"2026-10-05","via":"harvest"}},{"id":"scheels","value":0.4,"unit":"in","pm":0.05,"stated":"Height (From Surface of Hand Guard): 0.4 in.","source":{"type":"spec","publisher":"retailer","name":"Scheels, Magpul M-LOK QD Sling Mount (873750-MAG606), Specifications","url":"https://www.scheels.com/p/magpul-m-lok-qd-sling-mount/873750-MAG606/","retrieved":"2026-10-05","via":"harvest"}},{"id":"alexanders","value":0.4,"unit":"in","pm":0.05,"stated":"Height From Handguard Surface: 0.4 in","source":{"type":"spec","publisher":"retailer","name":"Alexander's Store, Magpul M-LOK QD Sling Mount - Forward Attachment (MAG606-BLK)","url":"https://alexandersstore.com/product/magpul-m-lok-qd-sling-mnt/","retrieved":"2026-10-05","via":"harvest"}},{"id":"dirty-bird","value":0.4,"unit":"in","pm":0.05,"stated":"Height: 0.4”","source":{"type":"spec","publisher":"retailer","name":"Dirty Bird, Magpul M-LOK QD Sling Mount - MPIMAG606","url":"https://dirtybirdusa.com/products/magpul-m-lok-qd-sling-mount/","retrieved":"2026-10-05","via":"harvest"}},{"id":"ar15discounts","value":0.4,"unit":"in","pm":0.05,"stated":"Height: 0.4”","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, Magpul M-LOK QD Sling Mount - MPIMAG606 (the same listing as Dirty Bird's)","url":"https://ar15discounts.com/products/magpul-m-lok-qd-sling-mount/","retrieved":"2026-10-05","via":"harvest"}},{"id":"patent","value":0.354,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/magpul-mlok-qd-sling-mount 687aa3642788 (US D746,404 S (Magpul, 'Firearm quick detach mount for a sling'), FIG. 5 top plan view (the mount from its side, the mounting face on top), 300 dpi)","scaleRef":"scale from magpul-mlok-qd-sling-mount.length = 1.321 in (x-extent 1569 px → 1187.7 px/in)","method":"height of the traced outline (tools/trace.py); the patent's side view at the plan's scale: the mounting face to the socket ring's face. FIG. 6, the end view, reads the same (417.5 px against FIG. 5's 418.5)","via":"harvest"}}],"adopt":{"from":"patent","reason":"What the outline is drawn to: the patent's side view at the plan's scale. It is the maker's 0.4 to one decimal, and it sits between that and Wing Tactical's 0.3, inside the rounding of each: 0.35 is where a figure rounds to one or the other. Nothing is stretched to make the 0.4: that would be 13% in one direction on a one-decimal figure."}},"width":{"label":"Width (side to side)","kind":"length","measurements":[{"id":"magpul","value":0.6,"unit":"in","pm":0.05,"stated":"Width, Max: 0.6 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, M-LOK QD Sling Mount (MAG606), Technical Specifications","url":"https://magpul.com/m-lok-qd-sling-mount.html","retrieved":"2026-10-05","via":"harvest"}},{"id":"wing","value":0.63,"unit":"in","stated":"Height: 0.63\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Magpul M-LOK QD Sling Attachment (MAG-606-BLK), Specifications (its own labels: Height, Length, Thickness; source of the figures unstated)","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/handguards-rails/rail-system-parts-accessories/magpul-m-lok-qd-sling-attachment/","retrieved":"2026-10-05","via":"harvest"},"note":"Wing's Height: of its three figures the one that is neither its Length nor its Thickness."},{"id":"primary-arms","value":0.6,"unit":"in","pm":0.05,"stated":"Width: 0.6\"","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Magpul M-LOK QD Sling Mount (SKU MAG606, MPN MAG606-BLK), Features","url":"https://www.primaryarms.com/magpul-m-lok-qd-sling-mount-mag606","retrieved":"2026-10-05","via":"harvest"}},{"id":"midwest","value":0.6,"unit":"in","pm":0.05,"stated":"Width, Max: 0.6 in.","source":{"type":"spec","publisher":"retailer","name":"Midwest Gun Works, Magpul M-LOK QD Sling Mount (MAG606), Specifications","url":"https://www.midwestgunworks.com/page/mgwi/prod/MAG606","retrieved":"2026-10-05","via":"harvest"}},{"id":"scheels","value":0.6,"unit":"in","pm":0.05,"stated":"Max Width: 0.6 in.","source":{"type":"spec","publisher":"retailer","name":"Scheels, Magpul M-LOK QD Sling Mount (873750-MAG606), Specifications","url":"https://www.scheels.com/p/magpul-m-lok-qd-sling-mount/873750-MAG606/","retrieved":"2026-10-05","via":"harvest"}},{"id":"alexanders","value":0.6,"unit":"in","pm":0.05,"stated":"Width: 0.6 in","source":{"type":"spec","publisher":"retailer","name":"Alexander's Store, Magpul M-LOK QD Sling Mount - Forward Attachment (MAG606-BLK)","url":"https://alexandersstore.com/product/magpul-m-lok-qd-sling-mnt/","retrieved":"2026-10-05","via":"harvest"}},{"id":"dirty-bird","value":0.6,"unit":"in","pm":0.05,"stated":"Width: 0.6”","source":{"type":"spec","publisher":"retailer","name":"Dirty Bird, Magpul M-LOK QD Sling Mount - MPIMAG606","url":"https://dirtybirdusa.com/products/magpul-m-lok-qd-sling-mount/","retrieved":"2026-10-05","via":"harvest"}},{"id":"ar15discounts","value":0.6,"unit":"in","pm":0.05,"stated":"Width: 0.6”","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, Magpul M-LOK QD Sling Mount - MPIMAG606 (the same listing as Dirty Bird's)","url":"https://ar15discounts.com/products/magpul-m-lok-qd-sling-mount/","retrieved":"2026-10-05","via":"harvest"}},{"id":"patent","value":0.601,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/magpul-mlok-qd-sling-mount 984ec513ef51 (US D746,404 S (Magpul, 'Firearm quick detach mount for a sling'), FIG. 3 front elevation (the outer face), 300 dpi)","scaleRef":"frame from the reviewed holes rear, front (1186.6 px/in, rms 0.000 in over 2 points): the two screw holes' centres, 934.4 px apart, as std.mlok.interval (20 mm)","method":"height of the traced outline (tools/trace.py); the plan outline's width (across the socket's ring, its widest) at the scale of its own two screw holes. The ring's own circle, fitted to its stroke, is 711.9 px across: 0.600. ± as the length's","via":"harvest"}}],"adopt":{"from":"magpul","reason":"The maker's figure, and the drawing's at the interval's scale to a thousandth (0.601): the second published size that scale has to meet, and does. Wing Tactical's 0.63 (its 'Height') is 5% over both."}},"weight":{"label":"Weight (with its two screws and T-nuts)","kind":"mass","measurements":[{"id":"magpul","value":0.62,"unit":"oz","stated":"Weight 0.62 oz. w/hardware","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, M-LOK QD Sling Mount (MAG606), Technical Specifications","url":"https://magpul.com/m-lok-qd-sling-mount.html","retrieved":"2026-10-05","via":"harvest"}},{"id":"primary-arms","value":0.5,"unit":"oz","pm":0.05,"stated":"Weight: 0.5 oz","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Magpul M-LOK QD Sling Mount (SKU MAG606, MPN MAG606-BLK), Features","url":"https://www.primaryarms.com/magpul-m-lok-qd-sling-mount-mag606","retrieved":"2026-10-05","via":"harvest"},"note":"Beside 'Machined from QPQ treated, heavy-duty steel' on the same page."},{"id":"midwest","value":0.5,"unit":"oz","pm":0.05,"stated":"Weight: 0.5 oz.","source":{"type":"spec","publisher":"retailer","name":"Midwest Gun Works, Magpul M-LOK QD Sling Mount (MAG606), Specifications","url":"https://www.midwestgunworks.com/page/mgwi/prod/MAG606","retrieved":"2026-10-05","via":"harvest"},"note":"The page says both 'Machined from Mil-Spec QPQ-finished steel' and 'Machined from Mil-Spec annodized aluminum for durability and light weight'."},{"id":"scheels","value":0.5,"unit":"oz","pm":0.05,"stated":"Weight: 0.5 oz.","source":{"type":"spec","publisher":"retailer","name":"Scheels, Magpul M-LOK QD Sling Mount (873750-MAG606), Specifications","url":"https://www.scheels.com/p/magpul-m-lok-qd-sling-mount/873750-MAG606/","retrieved":"2026-10-05","via":"harvest"}},{"id":"alexanders","value":0.5,"unit":"oz","pm":0.05,"stated":"Weight: 0.5 oz","source":{"type":"spec","publisher":"retailer","name":"Alexander's Store, Magpul M-LOK QD Sling Mount - Forward Attachment (MAG606-BLK)","url":"https://alexandersstore.com/product/magpul-m-lok-qd-sling-mnt/","retrieved":"2026-10-05","via":"harvest"}},{"id":"dirty-bird","value":0.5,"unit":"oz","pm":0.05,"stated":"Weight: 0.5 oz","source":{"type":"spec","publisher":"retailer","name":"Dirty Bird, Magpul M-LOK QD Sling Mount - MPIMAG606","url":"https://dirtybirdusa.com/products/magpul-m-lok-qd-sling-mount/","retrieved":"2026-10-05","via":"harvest"}},{"id":"ar15discounts","value":0.5,"unit":"oz","pm":0.05,"stated":"Weight: 0.5 oz","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, Magpul M-LOK QD Sling Mount - MPIMAG606 (the same listing as Dirty Bird's)","url":"https://ar15discounts.com/products/magpul-m-lok-qd-sling-mount/","retrieved":"2026-10-05","via":"harvest"}},{"id":"wing","value":0.45,"unit":"oz","stated":"Weight: 0.45 oz.","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Magpul M-LOK QD Sling Attachment (MAG-606-BLK), Specifications (its own labels: Height, Length, Thickness; source of the figures unstated)","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/handguards-rails/rail-system-parts-accessories/magpul-m-lok-qd-sling-attachment/","retrieved":"2026-10-05","via":"harvest"},"note":"Beside 'Material: Aluminum' and 'Finish: Mil-Spec Anodized'."}],"adopt":{"from":"magpul","reason":"The maker's own page as it is today, which says what the figure includes (its hardware) and calls the mount steel. The sellers' 0.5 oz, and one's 0.45, go with their aluminum wording and with the maker's 2018 sheet: by every sign the earlier mount, which a buyer today doesn't get."},"note":"Two weights go with two wordings of the material (the header): 0.62 oz with steel on the maker's page today, 0.5 oz on the sellers' pages (0.45 on one), most of which still say anodized aluminum, as the maker's 2018 sheet does. Primary Arms and Midwest Gun Works say steel beside the 0.5 oz: a page half brought up to date. Dirty Bird's and AR15Discounts' listing also has 'Additional information Weight 1.4 oz Dimensions 1.3 × 0.4 × 0.48 in': the shop's shipping fields, not recorded."},"lugs":{"label":"M-LOK slots its lugs span","kind":"count","measurements":[{"id":"photo","value":1,"unit":"count","source":{"type":"photo","photo":"references/magpul-mlok-qd-sling-mount 984ec513ef51 (US D746,404 S (Magpul, 'Firearm quick detach mount for a sling'), FIG. 3 front elevation (the outer face), 300 dpi)","scaleRef":"the two screw holes' centres, 934.4 px apart, as std.mlok.interval (20 mm)","method":"the plan is 1568 px long for 934 px between its screws: 33.6 mm for 20. Two nuts 20 mm apart sit in one 32 mm slot, and a mount a slot's length long covers one","via":"harvest"}},{"id":"sheet","value":1,"unit":"count","source":{"type":"photo","photo":"references/magpul-mlok-qd-sling-mount docs/f1074147b7.pdf (Magpul, MAG606 M-LOK QD Sling Mount installation instructions, 2018: the drawing under Step 1, rendered at 1500 dpi)","scaleRef":"none needed: a count","method":"the mount is drawn above a handguard's side with its two T-nuts under it, over one slot: a nut over each end of that slot (the slot 614 px long in the drawing, the nuts 367 px apart)","via":"harvest"}}],"adopt":{"from":"photo","reason":"The patent's plan, which gives the spacing; the maker's own drawing of it going on shows the same one slot."},"note":"No page says how many slots it needs in words; Magpul's bullet has it 'Quickly installs onto any M-LOK slot with simple tools', the slot in the singular. Its two screws are the M-LOK interval (20 mm) apart, which is how the patent's scale is set, so both T-nuts go into one 32 mm slot (std.mlok.slot_length), and the mount, 33.6 mm long, covers that slot and no more. Magpul's photo of it installed (feature _04) has it on one slot, the slot behind it ending short of its rear end."},"reach_inside":{"label":"Reach inside the handguard (below the mounting face, tightened)","kind":"length","measurements":[],"note":"Not sourced (as for the MVG and the hand stop: Magpul publishes no T-nut figure). The M-LOK tips sheet sets the nut by the surface's thickness ('the T-Nut \"gap\" must be slightly greater than the thickness of the mounting surface'), not by a figure."},"lug_x":{"label":"Rear lug's centre ahead of the part's rear end","kind":"length","measurements":[{"id":"patent","value":0.267,"unit":"in","pm":0.001,"source":{"type":"photo","photo":"references/magpul-mlok-qd-sling-mount 984ec513ef51 (US D746,404 S (Magpul, 'Firearm quick detach mount for a sling'), FIG. 3 front elevation (the outer face), 300 dpi)","scaleRef":"frame from the reviewed holes rear, front (1186.6 px/in, rms 0.000 in over 2 points)","method":"−x_min of the traced outline (tools/trace.py); the rear screw hole's centre ahead of the plan outline's rear end; the front one is as far from the front end (the plan is symmetric end for end)","via":"harvest"}}],"note":"The front screw is as far from the front end: the mount is the same end for end, and Magpul's M-LOK FAQ lets an accessory face either way, so which end is the rear is the build's."},"screw_seat_height":{"label":"The floor of each screw's pocket (where the screw's head bears) above the mounting face","kind":"length","measurements":[{"id":"patent","value":0.055,"unit":"in","pm":0.003,"source":{"type":"photo","photo":"references/magpul-mlok-qd-sling-mount 984ec513ef51 (US D746,404 S (Magpul, 'Firearm quick detach mount for a sling'), FIG. 2 front, top, left perspective view (an isometric view), 300 dpi)","scaleRef":"the elevations' scale (the two screw holes as std.mlok.interval: 1186.6 px/in), carried into FIG. 2 by a parallel projection fitted to the edges the elevations give (1.204 of their scale, each axis foreshortened to 0.983; the model's edges land within 1 px of FIG. 2's strokes)","method":"the screw hole's rim (r 130 px) and the pocket floor's outer edge (r 191 px), each slid along the screw's axis until its far arc lies on its stroke in the rear pocket: both at 65 px above the mounting face (64 to 66; about half of each arc shows, the rest is behind the pocket's near rim). The hole's lower edge, at the mounting face, lies on the sliver of a stroke that shows through the hole. ± 3 px","via":"harvest"}}],"note":"The pocket is a counterbore (FIG. 3: a circle 0.321 across round a 0.219 hole) cut from the outer surface down to this floor, so the wall under a screw's head is this thick. Both of the pocket's circles meet their strokes in FIG. 2 at the same height, 65 px of the elevations' scale; a pixel either way is plainly off."},"screw_head_diameter":{"label":"Screw's head, across","kind":"length","measurements":[{"id":"gallery-05","value":0.272,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-mlok-qd-sling-mount 181a18de5674 (Magpul gallery _05, 1200 x 1200: installed beside a light's mount, seen nearly square to its outer face, socket empty, both socket-head screws in)","scaleRef":"the two screws' centres in the same view, 155.4 px apart, as std.mlok.interval (20 mm): 197.4 px/in; the socket ring's face (100 px for 0.530 in: 188.8 px/in) is the nearer plane and bounds it the other way","method":"the lit face of the screw at the right, 53 px on its long axis (columns 391 to 443 at luminance over 120); the left one 52 px by eye. 0.268 to 0.281 in between the two scales","via":"harvest"}}]},"screw_head_top":{"label":"Screw's head: its top above the mounting face","kind":"length","measurements":[{"id":"feature-02","value":0.235,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-mlok-qd-sling-mount e5d098bfc86a (Magpul feature _02, 700 x 525: installed, seen from below along the handguard's side, a swivel and sling in the socket; a screw's knurled head stands in its pocket below the ring's face)","scaleRef":"the screw's own face in the same view, as .screw_head_diameter (0.272 in): 62 px on its long axis, 47 on its short (seen about 40 degrees off its axis)","method":"the knurled wall showing above the pocket's far rim, 12 px in the picture: 0.053 in as seen, 0.08 in along the screw's axis at that angle; taken as 0.07 above the rim's 0.165 in (the patent's surface at the pocket's far side). ± covers both ways of reading it","via":"harvest"}}],"note":"Rough, and for the look alone: the head's knurled wall shows above its pocket's rim on the side away from the ring and is sunk on the ring's side, its face well below the ring's (0.354). The drawing's surface is 0.165 in off the mounting face at the pocket's far rim."},"screw_hex":{"label":"Screw's socket: the hex wrench it takes (across flats)","kind":"length","measurements":[{"id":"sheet","value":0.15625,"unit":"in","stated":"Secure M-LOK Screws using a 5/32” hex wrench","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MAG606 M-LOK QD Sling Mount installation instructions (2018), Step 1","url":"https://magpul.com/media/wysiwyg/Instructions/MAG606_M-LOK_QD_Sling_Mount_INSRT.pdf","retrieved":"2026-10-05","via":"harvest"}}]}}},{"subject":"magpul-mlok-rail-cover-type-2","title":"Magpul M-LOK Rail Cover, Type 2 (MAG603: six to a pack; one in the hand stop kit, MAG608)","dimensions":{"length":{"label":"Overall length (along the handguard)","kind":"length","measurements":[{"id":"render","value":1.56,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/magpul-mlok-rail-cover-type-2 0474c600d6a0 (Supplied in chat 2026-10-02: a gallery image of an M-LOK handguard, straight side view, the hand stop kit on its bottom face and a row of Type 2 covers face on along its side face, rail teeth along the top, 2796 x 1290; a copy of the hand stop's)","scaleRef":"the covers' own pitch along the side face: the gaps between four covers in a row have their middles at u 671.96, 1217.20, 1762.81 and 2308.02 (rows 342 to 356), 545.2, 545.6 and 545.2 px apart, taken as the M-LOK slot pitch (std.mlok.slot_pitch, 40 mm: one cover to a slot): 346.3 px/in in the plane of the covers' edges","method":"one pitch less the gap between two covers, read where the background shows through it beside the handguard's face: u 1214.6 to 1219.7 at the half level on rows 349 to 356 of the seam at the image's middle, 5.1 px (5.1 and 5.2 px at the seams either side), which is 0.0147 in. ± 2 px on the gap's two edges (.cache/handstop-kit/magpul-mlok-rail-cover-type-2/measure_user.py)","via":"user"}},{"id":"patent-lugs","value":1.564,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-mlok-rail-cover-type-2 cbf4bce0c094 (US D755,332 S (Magpul, 'Slot cover set for a firearm'), FIG. 15 right side elevation of the set assembled, 300 dpi)","scaleRef":"the two lugs under the cover (broken lines: u 790 to 991 and 1512 to 1713), their middles 722 px apart, taken as the M-LOK interval (std.mlok.interval, 20 mm)","method":"the side elevation's length, 1434 px between the traced outline's two ends (u 534.5 and 1968.5), over the lugs' spacing. Nothing published says the lugs stand an interval apart (both drop into one slot): a check on the scale, not its source. ± 4 px on the lugs' middles and that assumption","via":"harvest"}}],"adopt":{"from":"render","reason":"Read on a picture of the product installed, against the slot pitch in its own plane. The patent's side elevation, scaled by its own lugs as the M-LOK interval, says 0.004 in more, inside both ±; and at the adopted length the patent's lugs read 0.270 in across for a 0.276 in slot (lug_width) and the cover's width reads what the image has (width)."},"note":"Less than the slot pitch by 0.015 in: two covers in neighbouring slots stand that far apart, as the image and Magpul's own photos of a row show them (a hairline between each two)."},"height":{"label":"Height (how far it stands off the handguard's face)","kind":"length","measurements":[{"id":"magpul","value":0.125,"unit":"in","pm":0.03,"stated":"Covers protrude just over 1/8\" above rail to maintain a low profile","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, M-LOK Rail Covers, Type 2 (MAG603), Features; the same page's banner: \"Covers barely protrude more than 1/8\" above the rail surface\"","url":"https://magpul.com/m-lok-rail-covers-type2.html","retrieved":"2026-10-05","via":"harvest"}},{"id":"sheet","value":0.125,"unit":"in","pm":0.03,"stated":"a protrusion that’s only slightly more than 1/8” from the mounting surface to maintain its low-profile","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, M-LOK Rail Covers, Type 2, information sheet (MAG603 GIS, 2025), p. 1; p. 2: \"Covers protrude only 1/8” above the rail surface\"","url":"https://magpul.com/media/wysiwyg/GIS/MAG603_M-LOK_Type_2_Rail_Covers_GIS_01.pdf","retrieved":"2026-10-05","via":"harvest"}},{"id":"patent","value":0.136,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/magpul-mlok-rail-cover-type-2 cbf4bce0c094 (US D755,332 S (Magpul, 'Slot cover set for a firearm'), FIG. 16 front elevation of the set assembled, 300 dpi)","scaleRef":"frame from the outline's two sides on the pad's level at the cover's width (920.1 px/in; the side elevation on the same sheet, scaled by the length, is 919.2)","method":"y_max of the traced outline (tools/trace.py); the patent's end elevation at the cover's width: the pad under its middle (the face that bears on the handguard, v 2587.5) up to the crown's top (v 2462.5): 125 px","via":"harvest"}}],"adopt":{"from":"patent","reason":"The maker gives a fraction and says 'just over' it; the patent's end elevation at the cover's own scale gives the figure a model needs, and it is just over 1/8 in: 0.011 in over."},"note":"The crown of the locking tab above the mounting face, which is the flat pad under the cover's middle (mounting_flat_width); the wings either side hang below that face (wing_drop). The maker's figure is a fraction said with 'just over', 'barely more than' and 'slightly more than': its ± here covers a sixteenth above it and nothing is claimed below."},"width":{"label":"Width (side to side)","kind":"length","measurements":[{"id":"patent","value":1.039,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-mlok-rail-cover-type-2 762c1cfdade3 (US D755,332 S (Magpul, 'Slot cover set for a firearm'), FIG. 17 top plan of the set assembled, 300 dpi)","scaleRef":"scale from magpul-mlok-rail-cover-type-2.length = 1.56 in (x-extent 1501 px → 962.2 px/in)","method":"height of the traced outline (tools/trace.py); the patent's plan at the cover's length: across the wings' two edges","via":"harvest"}},{"id":"render","value":1.036,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-mlok-rail-cover-type-2 0474c600d6a0 (Supplied in chat 2026-10-02: a gallery image of an M-LOK handguard, straight side view, the hand stop kit on its bottom face and a row of Type 2 covers face on along its side face, rail teeth along the top, 2796 x 1290; a copy of the hand stop's)","scaleRef":"the covers' own pitch along the side face in the same image (545.35 px to the M-LOK slot pitch, std.mlok.slot_pitch: 346.3 px/in in the plane of the covers' edges; the length's reading)","method":"a cover's two long edges, face on: the upper where its lit texture begins under the handguard's shadow line (row 322 ± 1.5; the line is rows 318 to 321) and the lower against the bright band under the row (row 680.9 at the half level, columns 800 and 1400): 358.9 px. Both edges are the wings' tips, in one plane; the face is square to the lens (the row's three pitches agree within 0.4 px either side of the image's middle)","via":"user"}}],"adopt":{"from":"patent","reason":"Line art, whole and orthographic, and the outline the model is built from. The image of the product agrees within 0.003 in: the patent's proportions are the product's."},"note":"No published figure. The patent's two sheets agree with each other too: the end elevation is 956 px across where the side elevation on its sheet is 1434 long (0.6667), the plan 1000 by 1501 (0.6662)."},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"wing","value":0.15,"unit":"oz","pm":0.005,"stated":"Weight: Handstop : 0.6 oz. Index Panel : 0.3 oz. Rail Cover : 0.15 oz. MOE Adapter : 0.3 oz.","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Magpul M-LOK Handstop Kit (MAG-608), Specifications (source of the figures unstated)","url":"https://www.wingtactical.com/firearm-parts/ar-15/handguards-rails/rail-system-parts-accessories/magpul-m-lok-handstop-kit/","retrieved":"2026-10-02","via":"harvest"}}],"note":"One cover. Magpul states no weight for the cover or for the pack of six (its page, its information sheet and its instruction sheet were read). The figure is a retailer's, from a list of the hand stop kit's pieces whose source isn't stated."},"lugs":{"label":"M-LOK slots it fills","kind":"count","measurements":[{"id":"magpul","value":1,"unit":"count","stated":"One cover fills one M-LOK slot, with six covers per package","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, M-LOK Rail Covers, Type 2 (MAG603), Features","url":"https://magpul.com/m-lok-rail-covers-type2.html","retrieved":"2026-10-05","via":"harvest"}},{"id":"configurator","value":2,"unit":"count","stated":"The hand stop occupies two M-LOK slots, the index panel one slot, and the rail cover spans two.","source":{"type":"spec","publisher":"review","name":"rifleconfigurator.com, Magpul M-LOK Hand Stop Kit (a configurator site; source of the statement unstated; the page is on file with the hand stop's seed)","url":"https://www.rifleconfigurator.com/catalog/controls/magpul-m-lok-hand-stop-kit","retrieved":"2026-10-02","via":"harvest"}}],"adopt":{"from":"magpul","reason":"The maker's own sentence, said three ways, and what its pictures of a row show: one cover to a slot, a hairline between each two. The site's statement is unattributed, and a cover 40 mm long can't span two slots 40 mm apart."},"note":"Magpul says it three times: the page's \"each cover can fill one M-LOK slot and are sold six to a package\", its feature list (below), and the information sheet's \"Includes six panels, each covering one M-LOK slot.\" The patent agrees: its two lugs stand 0.78 in apart and 1.0 in over their outer ends, inside one 32 mm slot. A configurator site's two slots (said of the kit's cover, unattributed) is kept as a conflict."},"reach_inside":{"label":"Reach inside the handguard (below the mounting face, locked)","kind":"length","measurements":[{"id":"patent","value":0.214,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-mlok-rail-cover-type-2 cbf4bce0c094 (US D755,332 S (Magpul, 'Slot cover set for a firearm'), FIG. 16 front elevation of the set assembled, 300 dpi)","scaleRef":"the traced end elevation's own scale (profiles.front: the cover's width, 920.1 px/in)","method":"the lowest of the broken lines under the pad (the tab's legs' feet, v 2784) below the pad's level (v 2587.5): 196.5 px","via":"harvest"}}],"note":"No published figure. The patent draws the two lugs and the locking tab's legs in them in broken lines, which it says show 'environment and unclaimed features': the only drawing of what stands in the slot, read at the cover's scale. The side elevation has the same reach (198 px at 919.2 px/in: 0.215). Whether the legs' feet stand lower or spread once the tab is home isn't drawn; the ± covers a design patent's broken lines."},"section_height":{"label":"Section height: the crown to the wings' tips","kind":"length","measurements":[{"id":"patent","value":0.247,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/magpul-mlok-rail-cover-type-2 cbf4bce0c094 (US D755,332 S (Magpul, 'Slot cover set for a firearm'), FIG. 15 right side elevation of the set assembled, 300 dpi)","scaleRef":"frame from the reviewed holes rear, front (919.2 px/in, rms 0.000 in over 2 points)","method":"height of the traced outline (tools/trace.py); the patent's side elevation at the cover's length: the crown's top to the wings' tips","via":"harvest"}}],"note":"The whole height of the cover seen from its side: its height above the mounting face and the wings' drop below it. Traced on the patent's side elevation; the end elevation on the same sheet has the same height (227 px each). The user's image shows three covers this way on the handguard's bottom face: 66 to 74 px there from the wing's tip (dark on the dark handguard: the shadow line on rows 709 to 717) to the crown (row 782, or 789.5 under a grey band), 0.20 to 0.22 in at that face's 337.6 px/in. Short of this figure by about what the picture's perspective takes (the near wing's tip stands half an inch nearer the lens than the crown, three quarters of an inch under its axis: 0.02 to 0.04 in at a lens 11 to 17 in away): a loose check, not a measurement."},"wing_drop":{"label":"Wings' tips below the mounting face","kind":"length","measurements":[{"id":"patent","value":0.111,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/magpul-mlok-rail-cover-type-2 cbf4bce0c094 (US D755,332 S (Magpul, 'Slot cover set for a firearm'), FIG. 16 front elevation of the set assembled, 300 dpi)","scaleRef":"frame from the reviewed holes left, right (920.1 px/in, rms 0.000 in over 2 points)","method":"−y_min of the traced outline (tools/trace.py); the patent's end elevation at the cover's width: the wings' tips below the pad under its middle","via":"harvest"}}],"note":"Each wing slopes down past the mounting face, over the handguard's corner beside the M-LOK face. Magpul's sentences about it: \"May not fit some free-float aluminum handguards that have wider, flatter profile\" (the page) and \"may not be compatible with free-float hand guards that have a wider and flatter profile, as they will not seat deep enough to allow the center portion to lock down\" (the information sheet)."},"mounting_flat_width":{"label":"Mounting face: the pad under the cover's middle, across","kind":"length","measurements":[{"id":"patent","value":0.611,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-mlok-rail-cover-type-2 cbf4bce0c094 (US D755,332 S (Magpul, 'Slot cover set for a firearm'), FIG. 16 front elevation of the set assembled, 300 dpi)","scaleRef":"the traced end elevation's own scale (profiles.front: the cover's width, 920.1 px/in)","method":"the flat between the two beads' feet on the traced outline: z -0.305 to +0.306. The pad's heavy line itself runs from u 963 to 1536 (573 px, 0.623 in), into the beads: the ± covers it","via":"harvest"}}],"note":"What bears on a handguard's M-LOK face: a flat pad under the cover's middle, a bead at each of its edges standing 0.011 in above it (into the cover), and beyond each bead a wing's underside rising from its tip at about 34 degrees. A face no wider than the pad with a corner falling away either side takes the cover flat; on a flat wider than about 0.70 in (where the wings' undersides come down to the pad's level) the wings bear first and the lugs don't reach: the maker's 'wider, flatter profile'."},"lug_width":{"label":"Lugs under the pad, across (the slot's width they stand in)","kind":"length","measurements":[{"id":"patent","value":0.27,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/magpul-mlok-rail-cover-type-2 cbf4bce0c094 (US D755,332 S (Magpul, 'Slot cover set for a firearm'), FIG. 16 front elevation of the set assembled, 300 dpi)","scaleRef":"the traced end elevation's own scale (profiles.front: the cover's width, 920.1 px/in)","method":"the lug's two sides just under the pad (broken lines, u 1127.5 and 1375.5 on rows 2608 to 2656): 248 px","via":"harvest"}}],"note":"A check on the scale that owes nothing to the image: the lugs drop into an M-LOK slot, 7 mm (0.276 in) wide. Lower down the broken lines are 255 px across (0.277 in): the latches that snap under the slot's edges."},"lug_spacing":{"label":"Lugs under the pad, middle to middle along the cover","kind":"length","measurements":[{"id":"patent","value":0.785,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/magpul-mlok-rail-cover-type-2 cbf4bce0c094 (US D755,332 S (Magpul, 'Slot cover set for a firearm'), FIG. 15 right side elevation of the set assembled, 300 dpi)","scaleRef":"the traced side elevation's own scale (profiles.side: the cover's length, 919.2 px/in)","method":"the two lugs' middles (broken lines: u 790 to 991 and 1512 to 1713): 722 px; ± 4 px","via":"harvest"}}],"note":"The M-LOK interval (20 mm, 0.787 in) within 0.002 in, as the four windows over them are (0.787 in on the plan). Each lug is 0.219 in long and the two span 1.00 in over their outer ends: inside one slot (32 mm), with room to spare along it."}}},{"subject":"magpul-moe-carbine","title":"Magpul MOE carbine stock, mil-spec","dimensions":{"length":{"label":"Overall length","kind":"length","measurements":[{"id":"magpul","value":7,"unit":"in","pm":0.05,"stated":"Length, max 7.0 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE Carbine Stock - Mil-Spec (MAG400)","url":"https://magpul.com/moe-carbine-stock-mil-spec.html","retrieved":"2026-10-01","via":"harvest"}},{"id":"primary-arms","value":6.9,"unit":"in","stated":"Length: 6.9”","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, MAG400-BLK","url":"https://www.primaryarms.com/magpul-moe-carbine-stock-mil-spec-black-mag400-blk","retrieved":"2026-10-01","via":"harvest"}},{"id":"big-tex","value":6.9,"unit":"in","pm":0.005,"stated":"Length, max: 6.90 in.","source":{"type":"spec","publisher":"retailer","name":"Big Tex Ordnance, MOE Carbine Stock, Mil-Spec (specifications)","url":"https://www.bigtexordnance.com/product/magpul-moe-carbine-stock-mil-spec-black/","retrieved":"2026-10-01","via":"harvest"}}],"adopt":{"from":"magpul","reason":"Magpul's current page. Retailers carry 6.9, an older figure of Magpul's by its wording at Big Tex (\"Length, max: 6.90 in.\": to the hundredth, so its ± is half of that)."}},"height":{"label":"Height","kind":"length","measurements":[{"id":"magpul","value":5.2,"unit":"in","stated":"Height, max 5.2 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE Carbine Stock - Mil-Spec (MAG400)","url":"https://magpul.com/moe-carbine-stock-mil-spec.html","retrieved":"2026-10-01","via":"harvest"}},{"id":"wing","value":5.26,"unit":"in","stated":"Height: 5.26\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, MOE Carbine Stock Mil-Spec","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/stocks-accessories/magpul-moe-carbine-stock-mil-spec/","retrieved":"2026-10-01","via":"harvest"}}],"adopt":{"from":"magpul","reason":"Manufacturer; the retailer's two-decimal figure rounds to it."}},"width":{"label":"Width","kind":"length","measurements":[{"id":"magpul","value":1.7,"unit":"in","stated":"Width, max 1.7 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE Carbine Stock - Mil-Spec (MAG400)","url":"https://magpul.com/moe-carbine-stock-mil-spec.html","retrieved":"2026-10-01","via":"harvest"}},{"id":"wing","value":1.59,"unit":"in","stated":"Width: 1.59\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, MOE Carbine Stock Mil-Spec","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/stocks-accessories/magpul-moe-carbine-stock-mil-spec/","retrieved":"2026-10-01","via":"harvest"},"note":"Not said where it is taken: the design patent's front view is 1.72 across the cheek and 1.25 across the butt."}],"adopt":{"from":"magpul","reason":"Manufacturer, and the patent's end view agrees with it when scaled by the height."}},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"magpul","value":8.4,"unit":"oz","stated":"Weight 8.4 oz.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE Carbine Stock - Mil-Spec (MAG400)","url":"https://magpul.com/moe-carbine-stock-mil-spec.html","retrieved":"2026-10-01","via":"harvest"}},{"id":"big-tex","value":8,"unit":"oz","pm":0.05,"stated":"Weight: 8.0 oz.","source":{"type":"spec","publisher":"retailer","name":"Big Tex Ordnance, MOE Carbine Stock, Mil-Spec (specifications)","url":"https://www.bigtexordnance.com/product/magpul-moe-carbine-stock-mil-spec-black/","retrieved":"2026-10-01","via":"harvest"}},{"id":"primary-arms","value":8,"unit":"oz","stated":"Weight: 8 oz","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, MAG400-BLK","url":"https://www.primaryarms.com/magpul-moe-carbine-stock-mil-spec-black-mag400-blk","retrieved":"2026-10-01","via":"harvest"}},{"id":"wing","value":8.57,"unit":"oz","stated":"Weight: 8.57 oz.","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, MOE Carbine Stock Mil-Spec","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/stocks-accessories/magpul-moe-carbine-stock-mil-spec/","retrieved":"2026-10-01","via":"harvest"}}],"adopt":{"from":"magpul","reason":"Magpul's current page. Retailers say 8.0 (Magpul's older figure) and 8.57."}},"lop_collapsed":{"label":"Length of pull, collapsed (the maker's reference rifle)","kind":"length","measurements":[{"id":"magpul","value":10.3,"unit":"in","stated":"LOP, M4 Collapsed ~10.3 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE Carbine Stock - Mil-Spec (MAG400)","url":"https://magpul.com/moe-carbine-stock-mil-spec.html","retrieved":"2026-10-01","via":"harvest"}},{"id":"primary-arms","value":10.5,"unit":"in","stated":"Length of pull - Collapsed: ~10.5","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, MAG400-BLK","url":"https://www.primaryarms.com/magpul-moe-carbine-stock-mil-spec-black-mag400-blk","retrieved":"2026-10-01","via":"harvest"}},{"id":"big-tex","value":10.7,"unit":"in","stated":"LOP, M4 Collapsed: ~10.7 in.","source":{"type":"spec","publisher":"retailer","name":"Big Tex Ordnance, MOE Carbine Stock, Mil-Spec (specifications)","url":"https://www.bigtexordnance.com/product/magpul-moe-carbine-stock-mil-spec-black/","retrieved":"2026-10-01","via":"harvest"}}],"adopt":{"from":"magpul","reason":"Magpul's current page. Retailers carry two earlier figures of Magpul's, 0.2 and 0.4 in longer."},"note":"Magpul has published three figures for this stock, and for the MOE SL three as well (11.1, 10.8, 10.9): taken pairwise from the highest down, the two stocks' difference comes out 0.4, 0.3 and 0.6 in, so it isn't what seats this one (butt_behind_pin_pos1)."},"lop_extended":{"label":"Length of pull, extended (the maker's reference rifle)","kind":"length","measurements":[{"id":"magpul","value":13.6,"unit":"in","stated":"LOP, M4 Extended ~13.6 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE Carbine Stock - Mil-Spec (MAG400)","url":"https://magpul.com/moe-carbine-stock-mil-spec.html","retrieved":"2026-10-01","via":"harvest"}},{"id":"primary-arms","value":13.8,"unit":"in","stated":"Length of pull - Extended: ~13.8”","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, MAG400-BLK","url":"https://www.primaryarms.com/magpul-moe-carbine-stock-mil-spec-black-mag400-blk","retrieved":"2026-10-01","via":"harvest"}},{"id":"big-tex","value":14,"unit":"in","pm":0.05,"stated":"LOP, M4 Extended: ~14.0 in.","source":{"type":"spec","publisher":"retailer","name":"Big Tex Ordnance, MOE Carbine Stock, Mil-Spec (specifications)","url":"https://www.bigtexordnance.com/product/magpul-moe-carbine-stock-mil-spec-black/","retrieved":"2026-10-01","via":"harvest"}}],"adopt":{"from":"magpul","reason":"Magpul's current page; the earlier figures move with the collapsed ones (the range is 3.3 in each time)."}},"lop_range":{"label":"Length-of-pull adjustment range","kind":"length","measurements":[{"id":"magpul","value":3.3,"unit":"in","stated":"LOP Adjustment Range 3.3 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE Carbine Stock - Mil-Spec (MAG400)","url":"https://magpul.com/moe-carbine-stock-mil-spec.html","retrieved":"2026-10-01","via":"harvest"}},{"id":"lop","value":3.3,"unit":"in","source":{"type":"derived","expr":"{.lop_extended} - {.lop_collapsed}","via":"harvest"}}],"adopt":{"from":"magpul","reason":"Stated; the two lengths of pull differ by it."}},"buttpad_thickness":{"label":"Rubber butt pad, thickness","kind":"length","measurements":[{"id":"magpul","value":0.3,"unit":"in","stated":"Removable 0.30\" Rubber Butt-Pad offers an anti-slip surface and increases impact protection","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE Carbine Stock - Mil-Spec (MAG400)","url":"https://magpul.com/moe-carbine-stock-mil-spec.html","retrieved":"2026-10-01","via":"harvest"}}]},"tube_axis_below_top":{"label":"Tube axis below the stock's top edge (at its highest)","kind":"length","measurements":[{"id":"installed","value":0.706,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-moe-carbine 5f6775e35c7e (Magpul: the MOE Carbine on a rifle, right side, close, 1200 px)","scaleRef":"the stock's own length, 641.4 px from the butt pad's rearmost point to the front face for Magpul's 7.0 in: 91.6 px/in (its height, 481 px for 5.2 in, gives 92.5). Not the tube's diameter: its limbs mirror the white ground, and it reads 102.1 px, 1.115 in","method":"the exposed tube's axis, midway between its limbs (row 480.2 at column 845), carried back along the top edge's 0.29° slope to the hump (row 476.8 at column 170), below the hump's top (412.2): 64.6 px","via":"harvest"},"note":"M6 first read 0.70 from the tube's diameter as the scale and the cheek's top without the slope: two slips that cancelled."},{"id":"installed-rifle","value":0.706,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-moe-carbine 314f5e1b0872 (Magpul: the MOE Carbine on a whole rifle, straight right side, 1200 x 1200)","scaleRef":"the receiver's Picatinny rail, ten slots at 13.03 px (std.picatinny.slot_pitch): 33.07 px/in; the handguard's rail reads 33.0 and 32.97 further forward","method":"the exposed tube's axis, midway between its limbs (row 505.15 over columns 278 to 294; the rifle lies level), below the hump's top (481.8): 23.35 px","via":"harvest"}},{"id":"patent","value":0.72,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/magpul-moe-carbine a74bc8906efc (US D600,308 S, Magpul's design patent, FIG. 4 front elevation, 300 dpi)","scaleRef":"the figure's height and width = Magpul's 5.2 and 1.7 in (156.3 and 157.1 px/in: within 0.5%)","method":"least-squares circle through the hidden-line bore (1.158 in across: the mil-spec tube's 1.148), its centre 112.6 px below the outline's top; ± for the dashes and the lines the fit takes in with them (rms 6 px)","via":"harvest"}}],"adopt":{"from":"installed","reason":"The tube itself in the stock, in two of Magpul's photos that agree. The design patent's bore agrees within the two ±."},"note":"The highest point is the hump at the butt, 0.05 in above the cheek's top line (the side outline's y = 0)."},"frame_width":{"label":"Width of the frame below the tube: the upright, the strut and the brace","kind":"length","measurements":[{"id":"patent","value":0.69,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/magpul-moe-carbine a74bc8906efc (US D600,308 S, Magpul's design patent, FIG. 4 front elevation, 300 dpi)","scaleRef":"the figure's height = Magpul's 5.2 in (156.3 px/in)","method":"the pair of lines inside the silhouette, read down columns 2.3 to 4.2 in below the top: 0.36 to 0.40 from the middle at 2.3 in, 0.29 to 0.36 at 3.9; ± is that taper","via":"harvest"}}],"note":"The cheek round the tube is the full 1.7 in and the butt about 1.25; the frame between them is much thinner. In the patent's front view it narrows from 0.78 in near the tube to 0.62 near the toe; one figure is used."},"pad_check_pitch":{"label":"The butt pad's checkering: the pitch of its grid (both ways)","kind":"length","measurements":[{"id":"patent","value":0.122,"unit":"in","pm":0.007,"source":{"type":"photo","photo":"references/magpul-moe-carbine a74bc8906efc (US D600,308 S, Magpul's design patent, FIG. 5 rear elevation, 300 dpi: the butt pad's face)","scaleRef":"the sheet's scale, which FIG. 4 beside it gives: its height = Magpul's 5.2 in (156.3 px/in; FIG. 4 and FIG. 5 span the same 837 px)","method":"the period of the grid's lines along the pad's height in the checkered band (autocorrelation of the column sums: 19 px, ± 1 px); across the width the squares read the same by eye (their X diagonals halve the period there)","via":"harvest"}}],"note":"The pad's face is checkered in square pyramids (FIG. 1, FIG. 5): a grid, the same pitch along the height and across."},"pad_check_depth":{"label":"The butt pad's checkering: how deep its grooves are","kind":"length","measurements":[{"id":"patent","value":0.033,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-moe-carbine 92e390b35525 (US D600,308 S, Magpul's design patent, FIG. 2 right side elevation, 300 dpi)","scaleRef":"the figure's height = Magpul's 5.2 in (135.4 px/in)","method":"the butt edge's serrations, peak to peak in 12-row windows along its checkered length (detrended): median 4.5 px; the scan's dotted stroke alone wanders 2 to 3 px, which the ± covers","via":"harvest"}},{"id":"patent-fig3","value":0.027,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-moe-carbine 92e390b35525 (US D600,308 S, FIG. 3 left side elevation, 300 dpi)","scaleRef":"the sheet's scale (FIG. 2's height = Magpul's 5.2 in: 135.4 px/in)","method":"the butt edge's top boundary over cols 720-1180, detrended, folded on its period (15.96 px): peak to valley 3.6 px of the mean tooth; FIG. 2 by the same method 4.0 px (0.030)","via":"harvest"}}],"adopt":{"from":"patent","reason":"The first reading; FIG. 3 by the folded profile agrees within its ±."},"note":"Seen edge-on along the butt in the side elevation: the pyramids' tips stand this far proud of the grooves between them. Their faces slope: folded on its period, the edge-on profile is a triangle wave (0.13-0.20 px rms against 0.29-0.33 for square grooves); the pyramids touch at their bases; a flat under 0.024 in at their tips can't be resolved (2026-10-03, .cache/research/magpul/tooth_profile.py)."},"pad_check_top":{"label":"The butt pad's checkering: where it begins below the pad's top","kind":"length","measurements":[{"id":"patent","value":1.27,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/magpul-moe-carbine a74bc8906efc (US D600,308 S, Magpul's design patent, FIG. 5 rear elevation, 300 dpi: the butt pad's face)","scaleRef":"the sheet's scale, which FIG. 4 beside it gives: its height = Magpul's 5.2 in (156.3 px/in; FIG. 4 and FIG. 5 span the same 837 px)","method":"the first column of the grid, 198 px from the pad's top end","via":"harvest"}}],"note":"Above it the pad is smooth round the tube's end (FIG. 5)."},"lock_pin_behind_front":{"label":"Lock pin behind the stock's front face","kind":"length","measurements":[{"id":"installed","value":2.37,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/magpul-moe-carbine 5f6775e35c7e (Magpul: the MOE Carbine on a rifle, right side, close, 1200 px)","scaleRef":"the stock's own length, 641.4 px for Magpul's 7.0 in: 91.6 px/in","method":"the pin's shaft (dark over columns 530 to 553: 0.25 in across) centred 216.7 px behind the front face (column 758.2)","via":"harvest"}}],"note":"The steel pin the latch draws out of the receiver extension's holes; its lower end shows in the slot beside the latch. Where it stands says which hole the stock is on."},"butt_behind_pin_pos3":{"label":"Butt behind the takedown pin as Magpul photographed it: two steps out (position 3)","kind":"length","measurements":[{"id":"installed","value":10.016,"unit":"in","pm":0.081,"source":{"type":"photo","photo":"references/magpul-moe-carbine 314f5e1b0872 (Magpul: the MOE Carbine on a whole rifle, straight right side, 1200 x 1200)","scaleRef":"frame from the reviewed holes takedown, pivot, selector (33.0 px/in, rms 0.011 in over 3 points)","method":"−x of the fitted profile's origin of the traced outline (tools/trace.py); the traced side outline's origin (the butt pad's rearmost point), fitted by rotation and translation at the outline's own scale to the stock's edges against the background","via":"harvest"}}],"note":"Which position it is in: its front face stands 1.31 in behind the castle nut here and 1.41 in in Magpul's closer view (5f6775e35c7e), and a stock can't pass the nut, so it is at most two steps out (2 × 0.66); one step out would leave it 0.65 in short of the nut when collapsed and its length of pull longer than the MOE SL's, which Magpul lists longer by 0.3 to 0.6 in. The ± covers the picture's perspective, read edge by edge: the lens is about 100 in away (the stock's front face shows as a 0.17 in sliver, and the stock reads 7.18 in long between its near edges), which puts the pins' heads 0.04 nearer the butt than their axis and the butt's near edge 0.1 behind its mid-plane: 9.97 so corrected. The two photos disagree by 0.1 in on where the stock sits behind the nut; neither says why."},"butt_behind_pin_pos1":{"label":"Butt behind the takedown pin at position 1 (collapsed), on a carbine receiver extension","kind":"length","measurements":[{"id":"installed","value":8.696,"unit":"in","pm":0.081,"source":{"type":"derived","expr":"{.butt_behind_pin_pos3} - 2 * {.lop_range} / 5","via":"harvest"},"note":"Two of the five steps of Magpul's 3.3 in range. ± is the photo's."},{"id":"holes","value":8.809,"unit":"in","pm":0.07,"source":{"type":"derived","expr":"{bcm-receiver-extension.tube_front_behind_pin} + {bcm-receiver-extension.tube_length} - {bcm-receiver-extension.position_hole_rear_from_rear} - 5 * {bcm-receiver-extension.position_step} - {.lock_pin_behind_front} + {.length}","via":"harvest"},"note":"The lock pin in the tube's front hole. ± for the hole's place (0.03), the tube's seat (0.02) and the pin's (0.04), and for the tube's length, which is a generic figure."},{"id":"from-sl","value":8.655,"unit":"in","pm":0.12,"source":{"type":"derived","expr":"{magpul-moe-sl-carbine.butt_behind_pin_pos1} - ({magpul-moe-sl-carbine.lop_collapsed} - {.lop_collapsed})","via":"harvest"},"note":"± is the SL seat's, and Magpul's two lengths of pull each given to a tenth with a tilde. With the figures retailers still carry for both stocks (10.8 and 10.5) it comes to 8.955."}],"adopt":{"from":"installed","reason":"Measured on a photo of the stock on a rifle; the tube's holes and the stock's lock pin agree within the two ±, and so do Magpul's current lengths of pull for it and the MOE SL, since that stock's seat was read again (2026-10-05): 0.04 in less, its front at the castle nut's rear face."},"note":"No photo on file shows it collapsed. Three ways to it: Magpul's photo of it two steps out, less the two steps; the tube's front hole (the Army's drawings seat the tube, BCM's photo places its holes) and where the stock's lock pin stands; and Magpul's lengths of pull for this stock and the MOE SL, whose seat is measured. The three agree within their ±: the first two leave its front face 0.03 and 0.14 in clear of the castle nut (bcm-castle-nut.rear_face_behind_pin), the last has it 0.01 inside. Until 2026-10-05 the last had it 0.20 in inside the nut, which couldn't be: it was the MOE SL's seat that was off, 0.19 in too far forward by a photo read at the wrong scale."},"bore_diameter":{"label":"The bore for the receiver extension, as the patent draws it","kind":"length","measurements":[{"id":"patent","value":1.158,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/magpul-moe-carbine a74bc8906efc (US D600,308 S, Magpul's design patent, FIG. 4 front elevation, 300 dpi)","scaleRef":"the figure's height and width = Magpul's 5.2 and 1.7 in (156.3 and 157.1 px/in: within 0.5%)","method":"the diameter of the least-squares circle through the hidden-line bore; ± is the fit's rms (6 px: the dashes, and the lines the fit takes in with them)","via":"harvest"}}],"note":"No published bore is on file for this stock, only that it is the Mil-Spec model (std.receiver_extension.milspec_od is 1.148). This is the circle tube_axis_below_top's patent reading takes its centre from. It isn't a clearance: its ± is wider than any, and the tube's own size lies inside it."},"rail_channel_width":{"label":"Width of the channel under the bore, for the receiver extension's indexing rail","kind":"length","measurements":[{"id":"rail","value":0.49,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.receiver_extension.rail_width}","via":"harvest"}}],"note":"Not read from this stock: the mil-spec tube's rail at its own width, with nothing to spare (no clearance is known). The patent's FIG. 4 draws the keyhole mouth; its neck hasn't been read."},"rail_channel_floor_below_axis":{"label":"Floor of the indexing rail's channel, below the tube axis","kind":"length","measurements":[{"id":"rail","value":0.874,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.receiver_extension.rail_bottom_below_axis}","via":"harvest"}}],"note":"Not read from this stock: where the mil-spec tube's rail ends below its axis, with nothing to spare (no clearance is known)."}}},{"subject":"magpul-moe-k2-plus","title":"Magpul MOE-K2+ grip (MAG532)","dimensions":{"grip_angle":{"label":"Grip angle from vertical","kind":"angle","measurements":[{"id":"spec","value":17,"unit":"deg","source":{"type":"spec","publisher":"manufacturer","name":"Magpul","url":"https://magpul.com/moe-k2-plus-grip-ar15-m4.html","retrieved":"2026-09-30","via":"brief"},"note":"Magpul does not say which line the angle is measured on."},{"id":"strap-photo","value":15.3,"unit":"deg","stated":"grip straps measure 15.3° from vertical","source":{"type":"photo","photo":"K2+ side product photo registered to the lower (not yet archived)","scaleRef":"takedown, trigger and hammer pins","method":"strap lines fitted in the registered photo","via":"brief"}},{"id":"installed-photo","value":15.74,"unit":"deg","pm":1.611,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 5d5e23b08431 (MOE-K2+ installed on a mil-spec lower, straight right side, 1200 px; supplied in chat)","scaleRef":"frame from the reviewed holes takedown, selector, trigger, hammer (118.8 px/in, rms 0.056 in over 4 points); the frame's four picks disagree pair by pair (106 to 127 px/in) and the grip reads 10% large in it, so it gives a direction and no size","method":"mean lean of the fitted profile's edges in the band 0.45–0.85 of its height (rear 16.8°, front 14.7°) of the traced outline, fitted at a free scale (1.103, rms 0.050 in) to the grip's edges (tools/trace.py)","via":"user"},"note":"16.043 ± 1.588 until 2026-10-03, fitted at the scale of an outline that was 12% too large."},{"id":"flat-top","value":17.89,"unit":"deg","pm":0.3,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 706ec3ae3e86 (black MOE-K2+, side view on white; supplied in chat, source not recorded)","scaleRef":"none needed: an angle within the outline","method":"the straps' lean from the flat top, the face that bears on the receiver's underside, in the photo as shot (.cache/k2-angle/asshot.py): the flat's straight stretch, columns 450 to 630 (the top edge to a tenth of a pixel in each), is a line sloping 0.12° down toward the front, rms 0.11 px; the straps' edges in the band 0.45–0.85 of the height lean 19.11° (rear) and 16.90° (front) from the photo's vertical, 18.00° in the mean. ± is the band chosen and the two straps' own 2.2° of taper.","via":"user"},"note":"16.04 until 2026-10-05, and the outline and the model turned 2° too upright with it: that reading turned the outline until a line through five points of its top was level, and one of the five was on the round of the block's front corner. The user's own grip, photographed on its side beside a tape (2d8cebb209a7, 6d81bb580120), has this outline's shape to 0.008 in at the median."},{"id":"patent","value":18.14,"unit":"deg","pm":0.5,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus b0778b51a67e (US D742,986 S, Magpul's design patent for the MOE-K2, FIG. 11 right side elevation, 300 dpi)","scaleRef":"none needed: an angle within the drawing","method":"the drawing's flat top is level on the page (0.04° over 480 columns); the outline's two edges in the band 0.45–0.85 of its height lean 19.02° (rear) and 17.26° (front) from its normal (.cache/k2-angle/patent.py: the ribs' crests, rms 5 px)","via":"harvest"},"note":"The MOE-K2, of which the K2+ is the overmolded version: the same body. A design patent's drawing isn't to a stated scale, but an elevation keeps its angles."},{"id":"installed-level","value":18.5,"unit":"deg","pm":0.6,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 5d5e23b08431 (MOE-K2+ installed on a mil-spec lower, straight right side, 1200 px; supplied in chat)","scaleRef":"none needed: an angle against the rifle's own level in the photo, which is turned 2.1 to 2.3° (the stock's top edge against the background rises 2.28° toward the muzzle over 220 columns, rms 0.09 px; the rail's four teeth in view rise 2.07°)","method":"the straps' edges against the background in the band 0.45–0.85 of the grip's height lean 17.26° (rear) and 15.49° (front) from the photo's vertical (.cache/k2-angle/installed.py), 19.4 and 17.6° from the rifle's; ± is the level's two readings and that neither edge is the bore's line","via":"user"},"note":"The same photo as installed-photo, read without the frame of four picks: the grip as it sits on a rifle."}],"adopt":{"from":"flat-top","reason":"Installed, the grip's flat top lies on the receiver's level underside, so the straps lean as they do from that face: an angle inside one photo, which no frame's scale touches. Magpul's patent elevation gives the same (18.1), and so does the grip on a rifle against the rifle's own level (18.5 ± 0.6); Magpul's 17° is the front strap's (16.8 to 17.3 in the three). The two older readings, 15.3 and 15.7 ± 1.6, were each made through a frame of receiver holes."},"note":"Corrected on 2026-10-05, at the user's word to look at it: 16.04 until then. Found that afternoon while the grip was being seated on the Workhorse: on the outline as it was turned, the flat top rose 2° toward the front and the block's front face leaned as much, where Magpul's patent and the MOE-K2 in the MOE-guard photo have that face square to the top. Three sources were then read for the angle itself, each on its own (the photo as shot, the patent, the grip on a rifle): 17.9, 18.1 and 18.5."},"receiver_to_bottom":{"label":"“Receiver to bottom” (Magpul)","kind":"length","measurements":[{"id":"spec","value":4.1,"unit":"in","source":{"type":"spec","publisher":"manufacturer","name":"Magpul","url":"https://magpul.com/moe-k2-plus-grip-ar15-m4.html","retrieved":"2026-09-30","via":"brief"},"note":"Magpul's reference point isn't stated; the user's own grip measures 4.15 ± 0.03 from its flat top to its toe (bottom_below_lower_underside, 2026-10-03), so the receiver here is the face the grip's flat top bears on."}]},"bottom_below_lower_underside":{"label":"Grip bottom below the lower's underside at the grip","kind":"length","measurements":[{"id":"photo","value":4.65,"unit":"in","source":{"type":"photo","photo":"K2+ side product photo (not yet archived)","scaleRef":"takedown, trigger and hammer pins","method":"registered to the lower by fitting the three pins; residuals ≤ 0.04 in","via":"brief"},"note":"The brief's figure, from a photo never archived. On the user's own grip the beavertail's top to the toe is 4.72 and the flat top to the toe 4.15: this reads as the grip's overall height taken for its drop."},{"id":"user-tape","value":4.15,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 2d8cebb209a7, 348ac23e1f32, 45eafc02ec88 (the user's own MOE-K2+ on a tile floor, a tape on the floor beside it: its side, its back strap, its top; 2026-10-03)","scaleRef":"the tape in each photo (256.5, 347.4 and 315.4 px/in at the floor), each reading brought to the grip's own height above the floor by the lens's height: one height, about 35 in, fits all three views, whose edges stand 0.65, 1.4 to 2.15 and 3.15 to 4.2 in up","method":"The traced side outline (profiles.side) laid on the grip's silhouette in each view: it fits at 0.892 ± 0.006 of the size the 4.65 gave it (the tape alone, uncorrected, caps it at 0.907: lying on its side the grip spans 2.00 to 6.39 on the tape, where that outline spans 4.86). ± is the lens's height (32 to 60 in) and the height of the silhouette's edge. Read again by eye on the side photo: its top on the 2 in line, its toe at 6.39. (.cache/photos/k2, 2026-10-03)","via":"user"},"note":"Magpul's own 'receiver to bottom', 4.1 (receiver_to_bottom, stated to one decimal), is this drop."}],"adopt":{"from":"user-tape","reason":"The user's own grip beside a tape, three views agreeing on one scale, and Magpul's 4.1 beside it. The brief's 4.65 made the grip 12% too large: its thickness then read 13% over Magpul's 1.2 on the patent's section, which was the same error."}},"grip_bottom_y":{"label":"Grip bottom in the rifle frame on the Workhorse, Y","kind":"length","measurements":[{"id":"brief","value":-5.2195,"unit":"in","source":{"type":"derived","expr":"{bad-workhorse-lower.grip_seat_y} - {.bottom_below_lower_underside}","via":"harvest"},"note":"The drop from the grip's seat: 4.15 by the user's own grip (2026-10-03; the id is from when the drop was the brief's 4.65). The installed photo that seemed to support 4.65 is framed by four picks that disagree with each other (106 to 127 px/in between pairs)."},{"id":"magpul","value":-5.1695,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{bad-workhorse-lower.grip_seat_y} - {.receiver_to_bottom}","via":"harvest"},"note":"Magpul's 4.1 in 'receiver to bottom', from the face the grip's flat top bears on (it had been read from the shelf's lower-front end, -6.116, while the drop was thought to be 4.65)."}],"adopt":{"from":"brief","reason":"The drop measured on the user's own grip, from the seat the lower gives; Magpul's 4.1, stated to one decimal, agrees."},"note":"From the grip's seat (bad-workhorse-lower.grip_seat_y). M2 hung the grip from grip_shelf_top_y (the bottom of the lower's step, 0.38 in lower), which put the bottom at −6.21; until 2026-10-03 the drop was the brief's 4.65 and the bottom −5.746; until 2026-10-05 the seat was 0.027 lower (the Workhorse's underside as a two-pin frame read it), and the bottom −5.246. Magpul's 'receiver to bottom', read from the same seat, agrees with the user's own grip."},"overall_height":{"label":"Overall height in the grip frame (the beavertail's top to the toe)","kind":"length","measurements":[{"id":"photo-black","value":4.773,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 706ec3ae3e86 (black MOE-K2+, side view on white; supplied in chat, source not recorded)","scaleRef":"the 4.15 in drop (magpul-moe-k2-plus.bottom_below_lower_underside), from the flat top's rear end to the toe (948 px, 228.5 px/in)","method":"height of the traced outline, the beavertail's top to the toe (tools/trace.py target), with the flat top level","via":"user"},"note":"4.733 until 2026-10-05, with the outline turned 2° too upright (grip_angle): the beavertail's tip, an inch behind the flat, stands 0.04 in higher over it when the flat is level. 5.292 while the drop was the brief's 4.65. On the user's own grip beside a tape the span read 4.72 ± 0.03 with the outline as it was turned then (.cache/photos/k2, 2026-10-03): the same grip, 4.76 in this frame."}],"note":"What the end section from Magpul's patent is scaled to (orthographic views share their height)."},"toe_y":{"label":"Toe (the grip's lowest point), Y in the grip frame","kind":"length","measurements":[{"id":"derived","value":-4.15,"unit":"in","source":{"type":"derived","expr":"-{.bottom_below_lower_underside}","via":"harvest"},"note":"Where the traced end section's toe sits, so it lines up with the side profile's."}]},"thickness":{"label":"Thickness","kind":"length","measurements":[{"id":"spec","value":1.2,"unit":"in","source":{"type":"spec","publisher":"manufacturer","name":"Magpul","url":"https://magpul.com/moe-k2-plus-grip-ar15-m4.html","retrieved":"2026-09-30","via":"brief"}},{"id":"patent","value":1.223,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus b0f42d6a9b13 (US D742,986 S, Magpul's design patent for the MOE-K2, FIG. 12 front elevation, 300 dpi)","scaleRef":"the traced side's overall height (magpul-moe-k2-plus.overall_height, 4.773 in, with the side's flat top level as the patent draws it): orthographic views share their height","method":"widest row of the traced front elevation, at the base's flare (tools/trace.py target)","via":"harvest"},"note":"Magpul's own drawing, scaled by our side outline. 1.213 while that outline was turned 2° too upright and 0.04 in shorter for it (until 2026-10-05); 1.356 while it was scaled by the brief's 4.65 drop: the conflict with Magpul's 1.2 was the drop's (bottom_below_lower_underside), as this note had half said (scaled by Magpul's 4.1 the section gave ~1.22)."},{"id":"user-tape","value":1.195,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 348ac23e1f32, e67aea4297df, 45eafc02ec88 (the user's own MOE-K2+ lying on its front strap, twice, and standing on its base, a tape on the floor beside it; 2026-10-03)","scaleRef":"the tape in each photo, brought to the body's widest (1.0 and 2.8 in above the floor) by the lens's height, 35 to 37 in (bottom_below_lower_underside's method)","method":"the body's two edges at its widest: 1.190, 1.198 and 1.196 in the three photos; ± is the lens's height (± 5 in) and where on the section the widest point stands (± 0.3 in)","via":"user"}}],"adopt":{"from":"spec","reason":"Magpul's published figure, which the user's own grip measures (1.195 ± 0.02). The patent's section read 13% wider only while the side outline it is scaled to was 12% too large (bottom_below_lower_underside)."}},"top_block_width":{"label":"Top block, across, just below the face that meets the receiver","kind":"length","measurements":[{"id":"user-tape","value":0.88,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 348ac23e1f32 (the user's own MOE-K2+ lying on its front strap, its back strap straight on, a tape on the floor beside it; 2026-10-03)","scaleRef":"the tape (347.4 px/in at the floor), brought up to the block's edges, 2.4 in above the floor, by the lens's height (37 in: bottom_below_lower_underside's method)","method":"the block's two edges below the beavertail's horns, columns 1167 and 1492 at row 643: 0.9384 on the tape, 0.878 at their height (0.859 to 0.891). The silhouette there is the block's sides and the beavertail's root together.","via":"user"}}],"note":"At the face itself it is 0.853 ± 0.015 (the top seen from above, 45eafc02ec88: its two straight edges, 4.0 to 4.2 in above the floor from 35 in); the patent's front elevation at the side's height has 0.885."},"lug_slot_width":{"label":"The slot in the top that goes over the receiver's lug, across","kind":"length","measurements":[{"id":"user-top","value":0.425,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 45eafc02ec88 (the user's own MOE-K2+ standing on its base, its top straight on from above, a tape on the floor beside it; 2026-10-03)","scaleRef":"the top face's own width in the same rows, 0.853 ± 0.015 (top_block_width's note: the face's two straight edges, by the tape and the lens's height)","method":"the slot's two walls and the face's two edges on 350 rows (985 to 1334 of the photo): the slot is 0.499 of the face (0.483 to 0.506, the rows' 10th to 90th percentile; 151.8 px of 304.7), and centred on it within 0.002 in. Both lie in the face's plane, so their ratio is free of the lens's height. ± is the face's own and the rows' spread. The edges found were looked at on the photo (.cache/grip-lower/slot.py, slot-edges.png, 2026-10-05).","via":"user"},"note":"The receiver's lug is .375 wide (std.ar15.grip_lug_width): 0.025 clear on each side. In plan the slot runs from a rear wall under the flat top's rear end to the nose's front face, which it is cut through, 1.44 to 1.47 in: where the standard lug's rear face and the trigger guard's ears stand, as near as a view whose ends are at different heights places them (0.06 in). A shallow step round its mouth (0.55 across), the screw's hole and the storage core's opening in its floor aren't measured."}]},"strap_face_width":{"label":"Back strap, across its ribbed face (between where it rounds into the sides)","kind":"length","measurements":[{"id":"user-tape","value":0.75,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 348ac23e1f32 (the user's own MOE-K2+ lying on its front strap, its back strap straight on; 2026-10-03)","scaleRef":"the body's width in the same view (thickness)","method":"the ribs run 0.7 to 0.8 in across the back strap, the body 1.2: what is left either side is where the strap rounds into the side","via":"user"}}]},"weight":{"label":"Weight (with hardware)","kind":"mass","measurements":[{"id":"spec","value":3.1,"unit":"oz","stated":"Weight: 3.1 oz.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul","url":"https://magpul.com/moe-k2-plus-grip-ar15-m4.html","retrieved":"2026-09-30","via":"harvest"}},{"id":"skdtac","value":3.3,"unit":"oz","stated":"Weight: 3.3 oz.","source":{"type":"spec","publisher":"retailer","name":"SKD Tactical","url":"https://skdtac.com/magpul-trade-moe-k2-grip-ar15-m4-1/","retrieved":"2026-09-30","via":"harvest"}}],"adopt":{"from":"spec","reason":"Manufacturer."}},"depth":{"label":"Front-to-back depth at mid-height (perpendicular to the straps)","kind":"length","measurements":[{"id":"photo","value":1.928,"unit":"in","pm":0.107,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 2886c49b6fd1 (Wing Tactical, ODG MOE-K2+, near-straight side view on white)","scaleRef":"the grip's drop from the lower's shelf (upper-rear end) to its lowest point, 4.15 in (magpul-moe-k2-plus.bottom_below_lower_underside: the user's own grip, 2026-10-03; these picks were first scaled by the brief's 4.65, 225.8 px/in) = 1050 px, i.e. 253.0 px/in; origin at the rear end of the grip's flat top (the shelf's upper-rear end)","method":"edge points picked on a gridded view (±10 px); photo vertical taken as installed vertical, because its straps average 16.4° from vertical, matching the 15.3–17° grip angle","via":"harvest"}},{"id":"photo-black","value":1.81,"unit":"in","pm":0.1,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 706ec3ae3e86 (black MOE-K2+, side view on white; supplied in chat, source not recorded)","scaleRef":"the 4.15 in drop (magpul-moe-k2-plus.bottom_below_lower_underside) = 948 px, i.e. 228.5 px/in, after rotating the outline to the adopted grip angle","method":"horizontal width at 2.56 in below the shelf (the Wing Tactical photo's mid-height station) × cos(grip angle), from the traced outline (tools/trace.py target); ± covers the station and the straps' 2° convergence","via":"user"},"note":"Re-derived 2026-09-30 by tools/trace.py. The prototype trace had rotated the photo the wrong way (straps at 20.4° instead of 15.3°), which inflated this to 2.13."}],"adopt":{"from":"photo","reason":"Two independent side photos agree within their ± (1.93 ± 0.11 and 1.80 ± 0.10, 7% apart; both rescaled on 2026-10-03 from the 4.65 drop to the 4.15 the user's own grip measures); the Wing Tactical reading is kept. Nothing renders from this value: the grip is drawn from the traced outline (profiles.side, black photo)."},"note":"The user sent the plain MOE-K2 version of this Wing Tactical shot (same shape, no rubber overmold); the harvested K2+ one is used."},"profile_back_top_x":{"label":"Profile: back strap at the shelf level, X (grip frame)","kind":"length","measurements":[{"id":"photo","value":-0.352,"unit":"in","pm":0.045,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 2886c49b6fd1 (Wing Tactical, ODG MOE-K2+, near-straight side view on white)","scaleRef":"the grip's drop from the lower's shelf (upper-rear end) to its lowest point, 4.15 in (magpul-moe-k2-plus.bottom_below_lower_underside: the user's own grip, 2026-10-03; these picks were first scaled by the brief's 4.65, 225.8 px/in) = 1050 px, i.e. 253.0 px/in; origin at the rear end of the grip's flat top (the shelf's upper-rear end)","method":"edge points picked on a gridded view (±10 px); photo vertical taken as installed vertical, because its straps average 16.4° from vertical, matching the 15.3–17° grip angle","via":"harvest"},"note":"The back-strap line extended up to the shelf level; the beavertail and web above it come with the M3 trace."}]},"profile_front_top_x":{"label":"Profile: front strap at the shelf level, X (grip frame)","kind":"length","measurements":[{"id":"photo","value":1.146,"unit":"in","pm":0.045,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 2886c49b6fd1 (Wing Tactical, ODG MOE-K2+, near-straight side view on white)","scaleRef":"the grip's drop from the lower's shelf (upper-rear end) to its lowest point, 4.15 in (magpul-moe-k2-plus.bottom_below_lower_underside: the user's own grip, 2026-10-03; these picks were first scaled by the brief's 4.65, 225.8 px/in) = 1050 px, i.e. 253.0 px/in; origin at the rear end of the grip's flat top (the shelf's upper-rear end)","method":"edge points picked on a gridded view (±10 px); photo vertical taken as installed vertical, because its straps average 16.4° from vertical, matching the 15.3–17° grip angle","via":"harvest"}}]},"profile_back_bottom_x":{"label":"Profile: rear-bottom corner, X (grip frame)","kind":"length","measurements":[{"id":"photo","value":-1.759,"unit":"in","pm":0.045,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 2886c49b6fd1 (Wing Tactical, ODG MOE-K2+, near-straight side view on white)","scaleRef":"the grip's drop from the lower's shelf (upper-rear end) to its lowest point, 4.15 in (magpul-moe-k2-plus.bottom_below_lower_underside: the user's own grip, 2026-10-03; these picks were first scaled by the brief's 4.65, 225.8 px/in) = 1050 px, i.e. 253.0 px/in; origin at the rear end of the grip's flat top (the shelf's upper-rear end)","method":"edge points picked on a gridded view (±10 px); photo vertical taken as installed vertical, because its straps average 16.4° from vertical, matching the 15.3–17° grip angle","via":"harvest"}}]},"profile_back_bottom_y":{"label":"Profile: rear-bottom corner, Y (grip frame)","kind":"length","measurements":[{"id":"photo","value":-3.565,"unit":"in","pm":0.045,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 2886c49b6fd1 (Wing Tactical, ODG MOE-K2+, near-straight side view on white)","scaleRef":"the grip's drop from the lower's shelf (upper-rear end) to its lowest point, 4.15 in (magpul-moe-k2-plus.bottom_below_lower_underside: the user's own grip, 2026-10-03; these picks were first scaled by the brief's 4.65, 225.8 px/in) = 1050 px, i.e. 253.0 px/in; origin at the rear end of the grip's flat top (the shelf's upper-rear end)","method":"edge points picked on a gridded view (±10 px); photo vertical taken as installed vertical, because its straps average 16.4° from vertical, matching the 15.3–17° grip angle","via":"harvest"}}]},"profile_front_bottom_x":{"label":"Profile: front-bottom corner, X (grip frame)","kind":"length","measurements":[{"id":"photo","value":0.296,"unit":"in","pm":0.045,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 2886c49b6fd1 (Wing Tactical, ODG MOE-K2+, near-straight side view on white)","scaleRef":"the grip's drop from the lower's shelf (upper-rear end) to its lowest point, 4.15 in (magpul-moe-k2-plus.bottom_below_lower_underside: the user's own grip, 2026-10-03; these picks were first scaled by the brief's 4.65, 225.8 px/in) = 1050 px, i.e. 253.0 px/in; origin at the rear end of the grip's flat top (the shelf's upper-rear end)","method":"edge points picked on a gridded view (±10 px); photo vertical taken as installed vertical, because its straps average 16.4° from vertical, matching the 15.3–17° grip angle","via":"harvest"}}]},"profile_front_bottom_y":{"label":"Profile: front-bottom corner, Y (grip frame)","kind":"length","measurements":[{"id":"photo","value":-4.127,"unit":"in","pm":0.045,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 2886c49b6fd1 (Wing Tactical, ODG MOE-K2+, near-straight side view on white)","scaleRef":"the grip's drop from the lower's shelf (upper-rear end) to its lowest point, 4.15 in (magpul-moe-k2-plus.bottom_below_lower_underside: the user's own grip, 2026-10-03; these picks were first scaled by the brief's 4.65, 225.8 px/in) = 1050 px, i.e. 253.0 px/in; origin at the rear end of the grip's flat top (the shelf's upper-rear end)","method":"edge points picked on a gridded view (±10 px); photo vertical taken as installed vertical, because its straps average 16.4° from vertical, matching the 15.3–17° grip angle","via":"harvest"}}]},"block_front_x":{"label":"Top block's foremost point, ahead of the flat top's rear end (the grip's half of its seat)","kind":"length","measurements":[{"id":"photo-black","value":1.33,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 706ec3ae3e86 (black MOE-K2+, side view on white; supplied in chat, source not recorded)","scaleRef":"scale from magpul-moe-k2-plus.bottom_below_lower_underside = 4.15 in (y from the origin to the far edge 948 px → 228.5 px/in)","method":"x_max in y [-1.26, -0.2] of the traced outline (tools/trace.py); the top block's foremost point ahead of the flat top's rear end: on its front face, which is straight (a line through 0.88 in of it lies 0.004 in behind this, rms 0.003) and 0.3° from square to the flat top","via":"user"}}],"note":"What of the grip comes nearest the rear face of the trigger guard's ears: seat_x puts it there. The face is flat and square to the top (Magpul's patent elevation, the MOE-K2 in the MOE-guard photo to within a pixel, and this outline since 2026-10-05). Until then the outline was turned 2° too upright (grip_angle), the face leaned on it, and this was its foot, 1.289 from an origin 0.067 in further forward: the flat top's rear end is found where the top leaves the flat's level by 4 px, and on a flat that rose toward the front that was short of the beavertail's curve."},"seat_x":{"label":"Seat, X: where the grip's frame origin (its flat top's rear end) sits ahead of the takedown pin, installed","kind":"length","measurements":[{"id":"interface","value":-0.155,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{std.ar15.receiver_rear_x} + {std.ar15.grip_lug_front_from_rear_face} - {.block_front_x}","via":"harvest"},"note":"(-0.114 until 2026-10-05, for the same place on the grip: the frame's origin is 0.067 in further back on it since the outline was turned to its flat top, block_front_x.) The top block's foremost point (block_front_x, on the traced side) on the rear face of the trigger guard's ears, where the Army drawing ends the lug (2.300 from the receiver's rear face, 1.175 ahead of the takedown pin). That the two meet is read where they do, in the MOE-guard photo (a MOE-K2 on a mil-spec lower, references/magpul-moe-trigger-guard a5dcf765dcd8): the seam between the block's front face and the lower is one dark line 2 to 3 px wide (0.012 in at most, at 258 px/in), straight from the receiver's underside down to the ears' foot and square to the pin line within 0.5°; the photo's frame has it 1.167 ahead of the pin and the rear guard screw beside it 1.181 (82 px behind its centre), either side of the drawing's 1.175."},{"id":"guard-photo","value":-0.11,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/magpul-moe-trigger-guard a5dcf765dcd8 (MOE guard and MOE-K2 installed on a mil-spec lower, close right side, 1222 px; supplied in chat)","scaleRef":"frame from the reviewed holes selector, trigger, rear_ear, front_ear (258.3 px/in, rms 0.011 in over 4 points)","method":"x of the fitted profile's origin of the traced outline (tools/trace.py); the traced K2+ outline, its flat top on the receiver's underside, slid along x until its front strap matches the photo's (43 rows below the lower)","via":"user"},"note":"-0.097 with the outline turned 2° too upright and its origin 0.067 in further forward (2026-10-05, earlier the same day); -0.128 before that, and the adopted seat until then: the frame's four places are the Workhorse's ledger values, and its two guard holes were that lower's own traced ones, the front one 0.042 in low (a frame of its two pins alone: bad-workhorse-lower.trigger_guard_front_y). At the drawing's places the four features fit to 0.011 in rms where they had fitted to 0.019, the receiver's underside is 0.024 higher (grip_mating_y), and the same 43 rows put the grip 0.031 further forward: the foot of its block's front face 0.017 past the ears' rear face, which a grip can't be, and which is inside this reading's ±. The rows leave a trend, 0.027 in per inch: the photo's front strap leans 16.7° in its frame and the outline's 15.3° over the same rows (the outline is turned 2° too upright: grip_angle), so a strap matched 1.5 to 2.3 in below the block can't place the block. (-0.291 until 2026-10-03, when the outline slid onto the strap was 12% too large, the 4.65 drop; at its size the rows match to 0.026 in, 10–90%.)"},{"id":"k2-installed","value":0.121,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 5d5e23b08431 (MOE-K2+ installed on a mil-spec lower, straight right side, 1200 px; supplied in chat)","scaleRef":"frame from the reviewed holes takedown, selector, trigger, hammer (118.8 px/in, rms 0.056 in over 4 points)","method":"x of the fitted profile's origin of the traced outline (tools/trace.py); the traced outline's origin (its flat top's rear end), fitted by rotation and translation (at the outline's own scale) to the grip's edges against the background","via":"user"},"note":"Read with the outline 12% too large (2026-10-03: the drop is 4.15, not 4.65), in a frame whose four picks disagree pair by pair (106 to 127 px/in) and in which the grip reads 10% large: the frame places nothing. Kept as read; the fit is now made at a free scale for the lean alone."}],"adopt":{"from":"interface","reason":"Where the grip stops is where it touches: the photo shows the block's front face on the lower's, a seam of 0.012 in at most, at the place the drawing gives the ears' rear face within 0.006 in. The strap matched through the photo's frame agrees within its ± (0.045 in further forward, ± 0.05) and can't say more: it moved 0.031 in with two of the frame's four places."},"note":"A grip's own figure on the standard AR-15 grip mount (D19): the lower gives the height (its underside, grip_seat_y), the grip says where its origin lands fore-aft. It was bad-workhorse-lower.grip_seat_x until M6. Seated by its interface since 2026-10-05, as the BCM grip is: the top block's front on the rear face of the trigger guard's ears, which is how the MOE-guard photo shows a K2 sitting (the seam between them, read where it is). Until then it was that photo's front strap matched through a frame of four features, -0.128, which changed by 0.031 in when the frame's guard holes went from the Workhorse's traced places to the drawing's: a seat read 1.5 in below the lower through a frame is as good as the frame, and the frame was the Workhorse's. The Magpul K2+ product photo (its takedown-pin pick 0.17 in off) put it 0.42 in forward, into the ear; that reading stays as a visible conflict."},"relief_top_rear_x":{"label":"Relief under the top block: its upper edge's rear end, X","kind":"length","measurements":[{"id":"patent","value":-0.162,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus b0778b51a67e (US D742,986 S, Magpul's design patent for the MOE-K2, FIG. 11 right side elevation, 300 dpi)","scaleRef":"the grip's own traced side outline (profiles.side, scaled by the 4.15 in drop) laid on the drawing's outer line: 502.6 px/in, turned 0.02 deg, the two 0.012 in apart at the median and 0.029 at the 90th percentile (the K2 of the drawing against the K2+ of the outline, and the line's own width)","method":"where the drawing's ink lies along columns every tenth of an inch from x -0.3 to 1.2 and rows from y 0.3 to -1.1, in the grip's frame (.cache/detail/magpul-moe-k2-plus/measure.py): the upper edge is a straight line, y -0.489 at x -0.15, -0.514 at 0, -0.545 at 0.2, -0.577 at 0.4, -0.609 at 0.6, -0.642 at 0.8, -0.666 at 0.95 (9.1 degrees down toward the front, each within 0.002 of the line), from the back strap's blend line at x -0.162 (rows -0.5 to -0.7) to where the floor's lower edge comes up to it at x 0.995. ± is the fit's and the line's width","via":"harvest"}}],"note":"The grip's sides between the top block (0.88 across) and the body (1.2) are a relief swept in a curve: a floor that leaves the block's side along a straight upper edge, and under it a steeper band whose lower edge is the line the grip is known by after its outline. Magpul's patent draws the three lines (the upper edge, the floor's lower edge, the relief's lower edge); the user's own grip and a seller's FDE one have the band where the patent has it (relief_floor_low_y). Until 2026-10-13 the model had a straight shoulder square to the strap there."},"relief_top_rear_y":{"label":"Relief under the top block: its upper edge's rear end, Y","kind":"length","measurements":[{"id":"patent","value":-0.487,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus b0778b51a67e (US D742,986 S, Magpul's design patent for the MOE-K2, FIG. 11 right side elevation, 300 dpi)","scaleRef":"the grip's own traced side outline (profiles.side, scaled by the 4.15 in drop) laid on the drawing's outer line: 502.6 px/in, turned 0.02 deg, the two 0.012 in apart at the median and 0.029 at the 90th percentile (the K2 of the drawing against the K2+ of the outline, and the line's own width)","method":"where the drawing's ink lies along columns every tenth of an inch from x -0.3 to 1.2 and rows from y 0.3 to -1.1, in the grip's frame (.cache/detail/magpul-moe-k2-plus/measure.py): the upper edge is a straight line, y -0.489 at x -0.15, -0.514 at 0, -0.545 at 0.2, -0.577 at 0.4, -0.609 at 0.6, -0.642 at 0.8, -0.666 at 0.95 (9.1 degrees down toward the front, each within 0.002 of the line), from the back strap's blend line at x -0.162 (rows -0.5 to -0.7) to where the floor's lower edge comes up to it at x 0.995. ± is the fit's and the line's width","via":"harvest"}}]},"relief_top_front_x":{"label":"Relief under the top block: its upper edge's front end, X","kind":"length","measurements":[{"id":"patent","value":0.995,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus b0778b51a67e (US D742,986 S, Magpul's design patent for the MOE-K2, FIG. 11 right side elevation, 300 dpi)","scaleRef":"the grip's own traced side outline (profiles.side, scaled by the 4.15 in drop) laid on the drawing's outer line: 502.6 px/in, turned 0.02 deg, the two 0.012 in apart at the median and 0.029 at the 90th percentile (the K2 of the drawing against the K2+ of the outline, and the line's own width)","method":"where the drawing's ink lies along columns every tenth of an inch from x -0.3 to 1.2 and rows from y 0.3 to -1.1, in the grip's frame (.cache/detail/magpul-moe-k2-plus/measure.py): the upper edge is a straight line, y -0.489 at x -0.15, -0.514 at 0, -0.545 at 0.2, -0.577 at 0.4, -0.609 at 0.6, -0.642 at 0.8, -0.666 at 0.95 (9.1 degrees down toward the front, each within 0.002 of the line), from the back strap's blend line at x -0.162 (rows -0.5 to -0.7) to where the floor's lower edge comes up to it at x 0.995. ± is the fit's and the line's width","via":"harvest"}}]},"relief_top_front_y":{"label":"Relief under the top block: its upper edge's front end, Y","kind":"length","measurements":[{"id":"patent","value":-0.673,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus b0778b51a67e (US D742,986 S, Magpul's design patent for the MOE-K2, FIG. 11 right side elevation, 300 dpi)","scaleRef":"the grip's own traced side outline (profiles.side, scaled by the 4.15 in drop) laid on the drawing's outer line: 502.6 px/in, turned 0.02 deg, the two 0.012 in apart at the median and 0.029 at the 90th percentile (the K2 of the drawing against the K2+ of the outline, and the line's own width)","method":"where the drawing's ink lies along columns every tenth of an inch from x -0.3 to 1.2 and rows from y 0.3 to -1.1, in the grip's frame (.cache/detail/magpul-moe-k2-plus/measure.py): the upper edge is a straight line, y -0.489 at x -0.15, -0.514 at 0, -0.545 at 0.2, -0.577 at 0.4, -0.609 at 0.6, -0.642 at 0.8, -0.666 at 0.95 (9.1 degrees down toward the front, each within 0.002 of the line), from the back strap's blend line at x -0.162 (rows -0.5 to -0.7) to where the floor's lower edge comes up to it at x 0.995. ± is the fit's and the line's width","via":"harvest"}}]},"relief_floor_rear_x":{"label":"Relief: the floor's lower edge (where the steeper band begins), its rear end, X","kind":"length","measurements":[{"id":"patent","value":-0.18,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus b0778b51a67e (US D742,986 S, Magpul's design patent for the MOE-K2, FIG. 11 right side elevation, 300 dpi)","scaleRef":"the grip's own traced side outline (profiles.side, scaled by the 4.15 in drop) laid on the drawing's outer line: 502.6 px/in, turned 0.02 deg, the two 0.012 in apart at the median and 0.029 at the 90th percentile (the K2 of the drawing against the K2+ of the outline, and the line's own width)","method":"where the drawing's ink lies along columns every tenth of an inch from x -0.3 to 1.2 and rows from y 0.3 to -1.1, in the grip's frame (.cache/detail/magpul-moe-k2-plus/measure.py): the upper edge is a straight line, y -0.489 at x -0.15, -0.514 at 0, -0.545 at 0.2, -0.577 at 0.4, -0.609 at 0.6, -0.642 at 0.8, -0.666 at 0.95 (9.1 degrees down toward the front, each within 0.002 of the line), from the back strap's blend line at x -0.162 (rows -0.5 to -0.7) to where the floor's lower edge comes up to it at x 0.995. ± is the fit's and the line's width","via":"harvest"}}],"note":"The floor's lower edge is an arc: through its rear end, its lowest point and its front point a circle of 0.854 in lies within 0.013 in of the drawing's line at every column read (y -0.806 at x -0.15, -0.889 at 0, -0.931 at 0.1, -0.960 at 0.2, -0.980 at 0.3, -0.985 at 0.4, -0.980 at 0.5, -0.959 at 0.6, -0.924 at 0.7, -0.876 at 0.8, -0.804 at 0.9, -0.756 at 0.95). Ahead of its front point it turns up to the upper edge's front end."},"relief_floor_rear_y":{"label":"Relief: the floor's lower edge, its rear end, Y","kind":"length","measurements":[{"id":"patent","value":-0.787,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus b0778b51a67e (US D742,986 S, Magpul's design patent for the MOE-K2, FIG. 11 right side elevation, 300 dpi)","scaleRef":"the grip's own traced side outline (profiles.side, scaled by the 4.15 in drop) laid on the drawing's outer line: 502.6 px/in, turned 0.02 deg, the two 0.012 in apart at the median and 0.029 at the 90th percentile (the K2 of the drawing against the K2+ of the outline, and the line's own width)","method":"where the drawing's ink lies along columns every tenth of an inch from x -0.3 to 1.2 and rows from y 0.3 to -1.1, in the grip's frame (.cache/detail/magpul-moe-k2-plus/measure.py): the upper edge is a straight line, y -0.489 at x -0.15, -0.514 at 0, -0.545 at 0.2, -0.577 at 0.4, -0.609 at 0.6, -0.642 at 0.8, -0.666 at 0.95 (9.1 degrees down toward the front, each within 0.002 of the line), from the back strap's blend line at x -0.162 (rows -0.5 to -0.7) to where the floor's lower edge comes up to it at x 0.995. ± is the fit's and the line's width","via":"harvest"}}]},"relief_floor_low_x":{"label":"Relief: the floor's lower edge, its lowest point, X","kind":"length","measurements":[{"id":"patent","value":0.4,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus b0778b51a67e (US D742,986 S, Magpul's design patent for the MOE-K2, FIG. 11 right side elevation, 300 dpi)","scaleRef":"the grip's own traced side outline (profiles.side, scaled by the 4.15 in drop) laid on the drawing's outer line: 502.6 px/in, turned 0.02 deg, the two 0.012 in apart at the median and 0.029 at the 90th percentile (the K2 of the drawing against the K2+ of the outline, and the line's own width)","method":"where the drawing's ink lies along columns every tenth of an inch from x -0.3 to 1.2 and rows from y 0.3 to -1.1, in the grip's frame (.cache/detail/magpul-moe-k2-plus/measure.py): the upper edge is a straight line, y -0.489 at x -0.15, -0.514 at 0, -0.545 at 0.2, -0.577 at 0.4, -0.609 at 0.6, -0.642 at 0.8, -0.666 at 0.95 (9.1 degrees down toward the front, each within 0.002 of the line), from the back strap's blend line at x -0.162 (rows -0.5 to -0.7) to where the floor's lower edge comes up to it at x 0.995. ± is the fit's and the line's width","via":"harvest"},"note":"Flat there: within 0.005 of its lowest from x 0.3 to 0.5."}]},"relief_floor_low_y":{"label":"Relief: the floor's lower edge, its lowest point, Y","kind":"length","measurements":[{"id":"patent","value":-0.985,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus b0778b51a67e (US D742,986 S, Magpul's design patent for the MOE-K2, FIG. 11 right side elevation, 300 dpi)","scaleRef":"the grip's own traced side outline (profiles.side, scaled by the 4.15 in drop) laid on the drawing's outer line: 502.6 px/in, turned 0.02 deg, the two 0.012 in apart at the median and 0.029 at the 90th percentile (the K2 of the drawing against the K2+ of the outline, and the line's own width)","method":"where the drawing's ink lies along columns every tenth of an inch from x -0.3 to 1.2 and rows from y 0.3 to -1.1, in the grip's frame (.cache/detail/magpul-moe-k2-plus/measure.py): the upper edge is a straight line, y -0.489 at x -0.15, -0.514 at 0, -0.545 at 0.2, -0.577 at 0.4, -0.609 at 0.6, -0.642 at 0.8, -0.666 at 0.95 (9.1 degrees down toward the front, each within 0.002 of the line), from the back strap's blend line at x -0.162 (rows -0.5 to -0.7) to where the floor's lower edge comes up to it at x 0.995. ± is the fit's and the line's width","via":"harvest"}}],"note":"Where the user's own grip and the FDE one have it: on the FDE photo (5aa8d0d21f23, the outline laid on it to 0.003 in) the tone down each column rises through the floor and is brightest between this edge and the relief's lower edge, at y -0.94 (x 0), -1.00 (0.2), -1.03 (0.4), -1.00 (0.6), -0.93 (0.8), and falls back within a tenth of an inch below it; on the user's own grip (2d8cebb209a7, from above with a tape beside it) the dark arc of the floor's deepest shade runs y -0.85 (x 0), -0.94 (0.17), -0.965 (0.37), -0.94 (0.57), -0.85 (0.77), 0.02 to 0.03 above this line all along."},"relief_floor_front_x":{"label":"Relief: the floor's lower edge, where it turns up to meet the upper edge, X","kind":"length","measurements":[{"id":"patent","value":0.95,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus b0778b51a67e (US D742,986 S, Magpul's design patent for the MOE-K2, FIG. 11 right side elevation, 300 dpi)","scaleRef":"the grip's own traced side outline (profiles.side, scaled by the 4.15 in drop) laid on the drawing's outer line: 502.6 px/in, turned 0.02 deg, the two 0.012 in apart at the median and 0.029 at the 90th percentile (the K2 of the drawing against the K2+ of the outline, and the line's own width)","method":"where the drawing's ink lies along columns every tenth of an inch from x -0.3 to 1.2 and rows from y 0.3 to -1.1, in the grip's frame (.cache/detail/magpul-moe-k2-plus/measure.py): the upper edge is a straight line, y -0.489 at x -0.15, -0.514 at 0, -0.545 at 0.2, -0.577 at 0.4, -0.609 at 0.6, -0.642 at 0.8, -0.666 at 0.95 (9.1 degrees down toward the front, each within 0.002 of the line), from the back strap's blend line at x -0.162 (rows -0.5 to -0.7) to where the floor's lower edge comes up to it at x 0.995. ± is the fit's and the line's width","via":"harvest"}}]},"relief_floor_front_y":{"label":"Relief: the floor's lower edge, where it turns up to meet the upper edge, Y","kind":"length","measurements":[{"id":"patent","value":-0.756,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus b0778b51a67e (US D742,986 S, Magpul's design patent for the MOE-K2, FIG. 11 right side elevation, 300 dpi)","scaleRef":"the grip's own traced side outline (profiles.side, scaled by the 4.15 in drop) laid on the drawing's outer line: 502.6 px/in, turned 0.02 deg, the two 0.012 in apart at the median and 0.029 at the 90th percentile (the K2 of the drawing against the K2+ of the outline, and the line's own width)","method":"where the drawing's ink lies along columns every tenth of an inch from x -0.3 to 1.2 and rows from y 0.3 to -1.1, in the grip's frame (.cache/detail/magpul-moe-k2-plus/measure.py): the upper edge is a straight line, y -0.489 at x -0.15, -0.514 at 0, -0.545 at 0.2, -0.577 at 0.4, -0.609 at 0.6, -0.642 at 0.8, -0.666 at 0.95 (9.1 degrees down toward the front, each within 0.002 of the line), from the back strap's blend line at x -0.162 (rows -0.5 to -0.7) to where the floor's lower edge comes up to it at x 0.995. ± is the fit's and the line's width","via":"harvest"}}]},"relief_band_width":{"label":"Relief: the band between the floor's lower edge and the relief's lower edge, at its lowest","kind":"length","measurements":[{"id":"patent","value":0.119,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus b0778b51a67e (US D742,986 S, Magpul's design patent for the MOE-K2, FIG. 11 right side elevation, 300 dpi)","scaleRef":"the grip's own traced side outline (profiles.side, scaled by the 4.15 in drop) laid on the drawing's outer line: 502.6 px/in, turned 0.02 deg, the two 0.012 in apart at the median and 0.029 at the 90th percentile (the K2 of the drawing against the K2+ of the outline, and the line's own width)","method":"where the drawing's ink lies along columns every tenth of an inch from x -0.3 to 1.2 and rows from y 0.3 to -1.1, in the grip's frame (.cache/detail/magpul-moe-k2-plus/measure.py): the upper edge is a straight line, y -0.489 at x -0.15, -0.514 at 0, -0.545 at 0.2, -0.577 at 0.4, -0.609 at 0.6, -0.642 at 0.8, -0.666 at 0.95 (9.1 degrees down toward the front, each within 0.002 of the line), from the back strap's blend line at x -0.162 (rows -0.5 to -0.7) to where the floor's lower edge comes up to it at x 0.995. ± is the fit's and the line's width","via":"harvest"}}],"note":"The relief's lower edge runs beside the floor's from x 0.2 forward (0.128 under it at x 0.2, 0.119 at 0.4, 0.117 at 0.5, 0.119 at 0.6, 0.115 at 0.8, 0.127 at 0.9: a circle about the same centre, this much larger, is within 0.016 in of the drawing's line from x 0.1 to 0.95), and behind that leaves it for the back strap in a straight line (relief_edge_rear_x). Ahead of x 0.95 it climbs the nose toward the block's upper front corner, beside the block's own front edge: not drawn (the nose is the three-view hull it was)."},"relief_edge_rear_x":{"label":"Relief: its lower edge's rear end, at the back strap's blend, X","kind":"length","measurements":[{"id":"patent","value":-0.3,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus b0778b51a67e (US D742,986 S, Magpul's design patent for the MOE-K2, FIG. 11 right side elevation, 300 dpi)","scaleRef":"the grip's own traced side outline (profiles.side, scaled by the 4.15 in drop) laid on the drawing's outer line: 502.6 px/in, turned 0.02 deg, the two 0.012 in apart at the median and 0.029 at the 90th percentile (the K2 of the drawing against the K2+ of the outline, and the line's own width)","method":"where the drawing's ink lies along columns every tenth of an inch from x -0.3 to 1.2 and rows from y 0.3 to -1.1, in the grip's frame (.cache/detail/magpul-moe-k2-plus/measure.py): the upper edge is a straight line, y -0.489 at x -0.15, -0.514 at 0, -0.545 at 0.2, -0.577 at 0.4, -0.609 at 0.6, -0.642 at 0.8, -0.666 at 0.95 (9.1 degrees down toward the front, each within 0.002 of the line), from the back strap's blend line at x -0.162 (rows -0.5 to -0.7) to where the floor's lower edge comes up to it at x 0.995. ± is the fit's and the line's width","via":"harvest"}}],"note":"From here the lower edge runs straight forward (y -1.017 at x -0.3, -1.021 at -0.25, -1.028 at -0.2, -1.036 at -0.15, -1.050 at 0, -1.066 at 0.1) until it meets the arc: the tangent from this point to the arc touches it at x 0.23, where the drawing has y -1.09."},"relief_edge_rear_y":{"label":"Relief: its lower edge's rear end, Y","kind":"length","measurements":[{"id":"patent","value":-1.017,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus b0778b51a67e (US D742,986 S, Magpul's design patent for the MOE-K2, FIG. 11 right side elevation, 300 dpi)","scaleRef":"the grip's own traced side outline (profiles.side, scaled by the 4.15 in drop) laid on the drawing's outer line: 502.6 px/in, turned 0.02 deg, the two 0.012 in apart at the median and 0.029 at the 90th percentile (the K2 of the drawing against the K2+ of the outline, and the line's own width)","method":"where the drawing's ink lies along columns every tenth of an inch from x -0.3 to 1.2 and rows from y 0.3 to -1.1, in the grip's frame (.cache/detail/magpul-moe-k2-plus/measure.py): the upper edge is a straight line, y -0.489 at x -0.15, -0.514 at 0, -0.545 at 0.2, -0.577 at 0.4, -0.609 at 0.6, -0.642 at 0.8, -0.666 at 0.95 (9.1 degrees down toward the front, each within 0.002 of the line), from the back strap's blend line at x -0.162 (rows -0.5 to -0.7) to where the floor's lower edge comes up to it at x 0.995. ± is the fit's and the line's width","via":"harvest"}}]},"relief_floor_rise":{"label":"Relief: how far the floor has widened the grip, each side, where the band begins","kind":"length","measurements":[{"id":"patent-front","value":0.05,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus b0f42d6a9b13 (US D742,986 S, Magpul's design patent for the MOE-K2, FIG. 12 front elevation, 300 dpi)","scaleRef":"the traced front elevation (profiles.front), scaled by the side's overall height (498.6 px/in: orthographic views share their height)","method":"the traced outline is 0.448 in half-wide down the top block, 0.471 at y -0.696 and 0.487 at y -0.752 (its points, the toe at -4.15), and at the body's width by -1.06 to -1.09: at the relief's rear end those two heights are 0.69 and 0.85 of the way from the upper edge (-0.487) to the floor's lower edge (-0.787), which on a floor that leaves the block's side tangent puts the floor's lower edge 0.048 and 0.054 in out from the block's side. Its next point, 0.558 at y -0.918, is then 0.57 of the way down the band to the lower edge's rear end (-1.017), where a straight band from this to the body's 0.6 has 0.555","via":"harvest"}}],"note":"No view looks along the relief; its depth is read off the grip's outline seen from the front, where the relief's rear end, the highest part of it, is the outline. The band then takes the grip from this to the body's width at the relief's lower edge. Assumed: the floor leaves the block's side without a crease and steepens toward the band (the FDE photo's tone rises steadily down the floor), and the band is straight."},"logo_plate_rear_x":{"label":"Logo plate (the recessed panel with MOE-K2+ / MADE IN USA, right side): its rear end, X","kind":"length","measurements":[{"id":"fde","value":0.13,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 5aa8d0d21f23 (Primary Arms, MAG532-FDE, near side view on white, 2200 x 1467)","scaleRef":"the grip's own traced side outline (profiles.side) laid on the photo's silhouette: 267.8 px/in, turned 0.24 deg, the two 0.003 in apart at the median and 0.008 at the 90th percentile: the pose of the photo the outline was traced from. The plate is on the block's side face, 0.44 in nearer the lens than the middle of the grip: nothing is read across that depth but its height below the top (logo_plate_top_y)","method":"the tone along rows through the plate's ends, in the grip's frame every 0.004 in (.cache/detail/magpul-moe-k2-plus/measure2.py): the rear end's bright edge at x 0.132 (rows -0.25, -0.30) and 0.134 (-0.34), the front end's dark edge at 0.99 (rows -0.25, -0.30) and 0.988 (-0.34), to 0.996 where the tone is the face's again; down columns x 0.25, 0.56 and 0.9 the upper edge's dark line at y -0.174, -0.176, -0.178 and the lower edge's bright one at -0.416, -0.416, -0.414 (level within 0.004 over 0.65 in). ± is three samples and the edge's own width","via":"harvest"}},{"id":"user","value":0.12,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 2d8cebb209a7 (the user's own MOE-K2+ on its side on tile, straight down from about 35 in, a tape beside it; 2026-10-03)","scaleRef":"the grip's own traced side outline laid on the photo's silhouette (259.8 px/in, turned 18.5 deg, 0.007 in apart at the median and 0.019 at the 90th percentile; at the base the fit stands 0.03 in off, by the bottom edge). The plate and the block's upper edge are both on the face turned to the lens","method":"the tone along rows and columns through the plate in the grip's frame (measure.py, measure2.py): the rear end's dark edge at x 0.11 to 0.13 and the front end's at 0.982 (row -0.235); the upper edge's dark line at y -0.118 and the lower edge at -0.35 (column 0.56)","via":"user"}}],"adopt":{"from":"fde","reason":"The seller's photo fits the outline to 0.003 in and is three times sharper on the plate; the user's own grip has the plate's end within 0.01 in of it."},"note":"A recess, by its edges' light: on the FDE photo its upper edge is a dark line and its lower a bright one (lit from above), its rear end bright and its front dark. The lettering stands in it and isn't drawn. Seen on the right side in every photo on file; no photo on file shows the left side of the top block square on, and the model has the plate on the right only."},"logo_plate_length":{"label":"Logo plate: its length along the top block","kind":"length","measurements":[{"id":"fde","value":0.866,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 5aa8d0d21f23 (Primary Arms, MAG532-FDE, near side view on white, 2200 x 1467)","scaleRef":"the grip's own traced side outline (profiles.side) laid on the photo's silhouette: 267.8 px/in, turned 0.24 deg, the two 0.003 in apart at the median and 0.008 at the 90th percentile: the pose of the photo the outline was traced from. The plate is on the block's side face, 0.44 in nearer the lens than the middle of the grip: nothing is read across that depth but its height below the top (logo_plate_top_y)","method":"the tone along rows through the plate's ends, in the grip's frame every 0.004 in (.cache/detail/magpul-moe-k2-plus/measure2.py): the rear end's bright edge at x 0.132 (rows -0.25, -0.30) and 0.134 (-0.34), the front end's dark edge at 0.99 (rows -0.25, -0.30) and 0.988 (-0.34), to 0.996 where the tone is the face's again; down columns x 0.25, 0.56 and 0.9 the upper edge's dark line at y -0.174, -0.176, -0.178 and the lower edge's bright one at -0.416, -0.416, -0.414 (level within 0.004 over 0.65 in). ± is three samples and the edge's own width","via":"harvest"}},{"id":"user","value":0.862,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 2d8cebb209a7 (the user's own MOE-K2+ on its side on tile, straight down from about 35 in, a tape beside it; 2026-10-03)","scaleRef":"the grip's own traced side outline laid on the photo's silhouette (259.8 px/in, turned 18.5 deg, 0.007 in apart at the median and 0.019 at the 90th percentile; at the base the fit stands 0.03 in off, by the bottom edge). The plate and the block's upper edge are both on the face turned to the lens","method":"the tone along rows and columns through the plate in the grip's frame (measure.py, measure2.py): the rear end's dark edge at x 0.11 to 0.13 and the front end's at 0.982 (row -0.235); the upper edge's dark line at y -0.118 and the lower edge at -0.35 (column 0.56)","via":"user"}}],"adopt":{"from":"fde","reason":"As logo_plate_rear_x; the user's own grip reads the same within 0.004 in."}},"logo_plate_top_y":{"label":"Logo plate: its upper edge below the face that bears on the receiver","kind":"length","measurements":[{"id":"fde","value":-0.154,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 5aa8d0d21f23 (Primary Arms, MAG532-FDE, near side view on white, 2200 x 1467)","scaleRef":"the grip's own traced side outline (profiles.side) laid on the photo's silhouette: 267.8 px/in, turned 0.24 deg, the two 0.003 in apart at the median and 0.008 at the 90th percentile: the pose of the photo the outline was traced from. The plate is on the block's side face, 0.44 in nearer the lens than the middle of the grip: nothing is read across that depth but its height below the top (logo_plate_top_y)","method":"the tone along rows through the plate's ends, in the grip's frame every 0.004 in (.cache/detail/magpul-moe-k2-plus/measure2.py): the rear end's bright edge at x 0.132 (rows -0.25, -0.30) and 0.134 (-0.34), the front end's dark edge at 0.99 (rows -0.25, -0.30) and 0.988 (-0.34), to 0.996 where the tone is the face's again; down columns x 0.25, 0.56 and 0.9 the upper edge's dark line at y -0.174, -0.176, -0.178 and the lower edge's bright one at -0.416, -0.416, -0.414 (level within 0.004 over 0.65 in). ± is three samples and the edge's own width","via":"harvest"},"note":"-0.176 against the outline's top, less the sliver's 0.022."},{"id":"user","value":-0.125,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 2d8cebb209a7 (the user's own MOE-K2+ on its side on tile, straight down from about 35 in, a tape beside it; 2026-10-03)","scaleRef":"the grip's own traced side outline laid on the photo's silhouette (259.8 px/in, turned 18.5 deg, 0.007 in apart at the median and 0.019 at the 90th percentile; at the base the fit stands 0.03 in off, by the bottom edge). The plate and the block's upper edge are both on the face turned to the lens","method":"the tone along rows and columns through the plate in the grip's frame (measure.py, measure2.py): the rear end's dark edge at x 0.11 to 0.13 and the front end's at 0.982 (row -0.235); the upper edge's dark line at y -0.118 and the lower edge at -0.35 (column 0.56)","via":"user"},"note":"-0.118 against the photo's own top edge, which the fit has at +0.007."}],"adopt":{"from":"fde","reason":"The sharper photo, in the pose the outline is traced from; the user's own grip has the edge 0.03 in higher, inside the two readings' ± together. Neither view is square to the block's side with a scale on it."},"note":"The seller's photo looks down on the grip's top a little: a sliver of the black top face 0.022 in tall shows along the outline's top (down columns x 0.3, 0.6 and 0.9 the white ends at y -0.002 and the black at -0.024), so the outline's top is the far edge of that face and whatever is on the near side face stands that much lower against it than it is below the face. The user's photo, from straight above the grip lying on its side, has the near edge as its outline."},"logo_plate_height":{"label":"Logo plate: its height","kind":"length","measurements":[{"id":"fde","value":0.238,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 5aa8d0d21f23 (Primary Arms, MAG532-FDE, near side view on white, 2200 x 1467)","scaleRef":"the grip's own traced side outline (profiles.side) laid on the photo's silhouette: 267.8 px/in, turned 0.24 deg, the two 0.003 in apart at the median and 0.008 at the 90th percentile: the pose of the photo the outline was traced from. The plate is on the block's side face, 0.44 in nearer the lens than the middle of the grip: nothing is read across that depth but its height below the top (logo_plate_top_y)","method":"the tone along rows through the plate's ends, in the grip's frame every 0.004 in (.cache/detail/magpul-moe-k2-plus/measure2.py): the rear end's bright edge at x 0.132 (rows -0.25, -0.30) and 0.134 (-0.34), the front end's dark edge at 0.99 (rows -0.25, -0.30) and 0.988 (-0.34), to 0.996 where the tone is the face's again; down columns x 0.25, 0.56 and 0.9 the upper edge's dark line at y -0.174, -0.176, -0.178 and the lower edge's bright one at -0.416, -0.416, -0.414 (level within 0.004 over 0.65 in). ± is three samples and the edge's own width","via":"harvest"}},{"id":"user","value":0.232,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 2d8cebb209a7 (the user's own MOE-K2+ on its side on tile, straight down from about 35 in, a tape beside it; 2026-10-03)","scaleRef":"the grip's own traced side outline laid on the photo's silhouette (259.8 px/in, turned 18.5 deg, 0.007 in apart at the median and 0.019 at the 90th percentile; at the base the fit stands 0.03 in off, by the bottom edge). The plate and the block's upper edge are both on the face turned to the lens","method":"the tone along rows and columns through the plate in the grip's frame (measure.py, measure2.py): the rear end's dark edge at x 0.11 to 0.13 and the front end's at 0.982 (row -0.235); the upper edge's dark line at y -0.118 and the lower edge at -0.35 (column 0.56)","via":"user"}}],"adopt":{"from":"fde","reason":"As logo_plate_rear_x; the user's own grip reads 0.006 in less."}},"logo_plate_corner_r":{"label":"Logo plate: the round of its corners","kind":"length","measurements":[{"id":"fde","value":0.07,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 5aa8d0d21f23 (Primary Arms, MAG532-FDE, near side view on white, 2200 x 1467)","scaleRef":"the traced side outline laid on the photo's silhouette (267.8 px/in: logo_plate_rear_x)","method":"how far the ends stand in along rows near the upper and lower edges (measure2.py): 0.019 in from an edge the rear end is 0.016 to 0.03 in further in and the front end 0.03 to 0.04, and 0.034 in from it 0.008 and 0.014: rounds of 0.06 to 0.08 in","via":"harvest"}}]},"detail_relief":{"label":"How far the logo plate's floor is sunk in the block's side (no view shows it in profile)","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the least the page draws (docs/research/model-detail-pass-2026-10-12.md). The plate's upper and lower walls show as lines 0.012 in wide in the FDE photo.","via":"harvest"}}]},"beavertail_edge_round":{"label":"Beavertail: the round of its rear face's two edges","kind":"length","measurements":[{"id":"patent-rear","value":0.111,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus b0f42d6a9b13 (US D742,986 S, Magpul's design patent for the MOE-K2, FIG. 13 rear elevation, 300 dpi)","scaleRef":"the figure's own height, the horns' tips to the base, 2382 px for the side's overall height (magpul-moe-k2-plus.overall_height, 4.773 in: 499 px/in), which has the body 1.195 in wide at the ribs (596 px)","method":"the ink along rows 580 and 620 of the sheet, 0.21 and 0.29 in below the horns' tips: the outer line at columns 1402 and 1844.5, the lines inside it at 1457.5 and 1788 (55.5 and 56.5 px); the same from row 500 to 660. ± is the line's width and the scale's","via":"harvest"}}],"note":"Seen from behind, the beavertail's rear face has a line 0.11 in inside each edge of its outline for its whole height: where the rounds end. Until 2026-10-13 its edges were broken at 0.05 in two flats."},"base_lip_height":{"label":"Base: the black lip's height at the grip's corners, from its bottom edge along the strap's axis","kind":"length","measurements":[{"id":"fde","value":0.166,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 5aa8d0d21f23 (Primary Arms, MAG532-FDE, near side view on white, 2200 x 1467)","scaleRef":"the grip's own traced side outline (profiles.side) laid on the photo's silhouette: 267.8 px/in, 0.003 in apart at the median (logo_plate_rear_x)","method":"down columns every 0.05 to 0.1 in from x -1.55 to 0.3 in the grip's frame, where the overmould's colour ends (the tone falls under 60: measure.py), turned to the strap's axis (grip_angle) and taken from the outline's bottom edge under it: 0.163, 0.169 behind the step (x -1.5, -1.2), 0.166, 0.171, 0.15 ahead of it (x -0.05, 0.2, 0.3); on the step's top 0.295 and 0.298 (x -0.8 to -0.4, -0.2). The step begins to rise 0.065 in ahead of the grip frame's origin along the base (square to the strap's axis) and is at its height by 0.21; it leaves it at 1.01 and is down by 1.105. ± is two samples, the outline's bottom edge and the lens: the photo looks a little down on the grip (logo_plate_top_y)","via":"harvest"}}],"note":"The overmould ends on the hard core along a line that runs beside the bottom edge and rises in a step mid-side, where the cap's latch sits in the core (base_tab_height). Read on a coloured grip, where the line is the colour's edge; the user's own black grip has it as a hairline in the same shape (2d8cebb209a7: 0.03 in higher all along, as that photo's fit stands at the base), and Magpul's patent draws it 0.03 to 0.05 in higher on the MOE-K2. Until 2026-10-13 the model's base was cut square across at 0.239 in."},"base_tab_height":{"label":"Base: the height of the step in the black lip mid-side, from the bottom edge along the strap's axis","kind":"length","measurements":[{"id":"fde","value":0.296,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 5aa8d0d21f23 (Primary Arms, MAG532-FDE, near side view on white, 2200 x 1467)","scaleRef":"the grip's own traced side outline (profiles.side) laid on the photo's silhouette: 267.8 px/in, 0.003 in apart at the median (logo_plate_rear_x)","method":"down columns every 0.05 to 0.1 in from x -1.55 to 0.3 in the grip's frame, where the overmould's colour ends (the tone falls under 60: measure.py), turned to the strap's axis (grip_angle) and taken from the outline's bottom edge under it: 0.163, 0.169 behind the step (x -1.5, -1.2), 0.166, 0.171, 0.15 ahead of it (x -0.05, 0.2, 0.3); on the step's top 0.295 and 0.298 (x -0.8 to -0.4, -0.2). The step begins to rise 0.065 in ahead of the grip frame's origin along the base (square to the strap's axis) and is at its height by 0.21; it leaves it at 1.01 and is down by 1.105. ± is two samples, the outline's bottom edge and the lens: the photo looks a little down on the grip (logo_plate_top_y)","via":"harvest"}}]},"base_tab_rear_foot_u":{"label":"Base: where the lip's step begins to rise, along the base from the grip frame's origin (square to the strap's axis)","kind":"length","measurements":[{"id":"fde","value":0.065,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 5aa8d0d21f23 (Primary Arms, MAG532-FDE, near side view on white, 2200 x 1467)","scaleRef":"the grip's own traced side outline (profiles.side) laid on the photo's silhouette: 267.8 px/in, 0.003 in apart at the median (logo_plate_rear_x)","method":"down columns every 0.05 to 0.1 in from x -1.55 to 0.3 in the grip's frame, where the overmould's colour ends (the tone falls under 60: measure.py), turned to the strap's axis (grip_angle) and taken from the outline's bottom edge under it: 0.163, 0.169 behind the step (x -1.5, -1.2), 0.166, 0.171, 0.15 ahead of it (x -0.05, 0.2, 0.3); on the step's top 0.295 and 0.298 (x -0.8 to -0.4, -0.2). The step begins to rise 0.065 in ahead of the grip frame's origin along the base (square to the strap's axis) and is at its height by 0.21; it leaves it at 1.01 and is down by 1.105. ± is two samples, the outline's bottom edge and the lens: the photo looks a little down on the grip (logo_plate_top_y)","via":"harvest"}}]},"base_tab_rear_top_u":{"label":"Base: where the lip's step has reached its height, along the base","kind":"length","measurements":[{"id":"fde","value":0.21,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 5aa8d0d21f23 (Primary Arms, MAG532-FDE, near side view on white, 2200 x 1467)","scaleRef":"the grip's own traced side outline (profiles.side) laid on the photo's silhouette: 267.8 px/in, 0.003 in apart at the median (logo_plate_rear_x)","method":"down columns every 0.05 to 0.1 in from x -1.55 to 0.3 in the grip's frame, where the overmould's colour ends (the tone falls under 60: measure.py), turned to the strap's axis (grip_angle) and taken from the outline's bottom edge under it: 0.163, 0.169 behind the step (x -1.5, -1.2), 0.166, 0.171, 0.15 ahead of it (x -0.05, 0.2, 0.3); on the step's top 0.295 and 0.298 (x -0.8 to -0.4, -0.2). The step begins to rise 0.065 in ahead of the grip frame's origin along the base (square to the strap's axis) and is at its height by 0.21; it leaves it at 1.01 and is down by 1.105. ± is two samples, the outline's bottom edge and the lens: the photo looks a little down on the grip (logo_plate_top_y)","via":"harvest"}}]},"base_tab_front_top_u":{"label":"Base: where the lip's step leaves its height at the front, along the base","kind":"length","measurements":[{"id":"fde","value":1.01,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 5aa8d0d21f23 (Primary Arms, MAG532-FDE, near side view on white, 2200 x 1467)","scaleRef":"the grip's own traced side outline (profiles.side) laid on the photo's silhouette: 267.8 px/in, 0.003 in apart at the median (logo_plate_rear_x)","method":"down columns every 0.05 to 0.1 in from x -1.55 to 0.3 in the grip's frame, where the overmould's colour ends (the tone falls under 60: measure.py), turned to the strap's axis (grip_angle) and taken from the outline's bottom edge under it: 0.163, 0.169 behind the step (x -1.5, -1.2), 0.166, 0.171, 0.15 ahead of it (x -0.05, 0.2, 0.3); on the step's top 0.295 and 0.298 (x -0.8 to -0.4, -0.2). The step begins to rise 0.065 in ahead of the grip frame's origin along the base (square to the strap's axis) and is at its height by 0.21; it leaves it at 1.01 and is down by 1.105. ± is two samples, the outline's bottom edge and the lens: the photo looks a little down on the grip (logo_plate_top_y)","via":"harvest"}}]},"base_tab_front_foot_u":{"label":"Base: where the lip's step is down again at the front, along the base","kind":"length","measurements":[{"id":"fde","value":1.105,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 5aa8d0d21f23 (Primary Arms, MAG532-FDE, near side view on white, 2200 x 1467)","scaleRef":"the grip's own traced side outline (profiles.side) laid on the photo's silhouette: 267.8 px/in, 0.003 in apart at the median (logo_plate_rear_x)","method":"down columns every 0.05 to 0.1 in from x -1.55 to 0.3 in the grip's frame, where the overmould's colour ends (the tone falls under 60: measure.py), turned to the strap's axis (grip_angle) and taken from the outline's bottom edge under it: 0.163, 0.169 behind the step (x -1.5, -1.2), 0.166, 0.171, 0.15 ahead of it (x -0.05, 0.2, 0.3); on the step's top 0.295 and 0.298 (x -0.8 to -0.4, -0.2). The step begins to rise 0.065 in ahead of the grip frame's origin along the base (square to the strap's axis) and is at its height by 0.21; it leaves it at 1.01 and is down by 1.105. ± is two samples, the outline's bottom edge and the lens: the photo looks a little down on the grip (logo_plate_top_y)","via":"harvest"}}]},"latch_window_rear_u":{"label":"Base: the opening the cap's latch sits in, its rear end, along the base","kind":"length","measurements":[{"id":"fde","value":0.243,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 5aa8d0d21f23 (Primary Arms, MAG532-FDE, near side view on white, 2200 x 1467)","scaleRef":"the grip's own traced side outline laid on the photo's silhouette: 267.8 px/in (logo_plate_rear_x)","method":"the tone down columns through the black lip every 0.02 in (measure.py) and the opening's corners on the resampled photo (rect/5aa-base.png, 800 px/in), turned to the strap's axis: the opening's rear edge runs along the axis 0.243 in ahead of the origin (its corner at x -0.926 y -3.655, its foot at -0.97, -3.80) and its front edge at 0.93 (the dark runs to the bottom down column -0.3 and is gone by -0.25); its upper edge is 0.192, 0.189 and 0.192 in above the outline's lowest point at columns -0.8, -0.6, -0.4, 0.180 above the bottom edge under it; the latch's top is 0.048 in under that (the dark band), its ends 0.03 to 0.04 in inside the opening's. On the user's own grip (2d8cebb209a7) the dark band is 0.05 to 0.06 in tall and the opening 0.69 long","via":"harvest"}}],"note":"Under the step each side of the base has an opening in the core's lip, open at the bottom, with the cap's latch standing in it: on the user's black grip the dark slot round the latch is what shows most of the base. Both sides have one (the patent's rear elevation and bottom plan are symmetric; a seller's photo of the base with its cap off, 076955272fb6, has a notch in each side's rim)."},"latch_window_front_u":{"label":"Base: the latch's opening, its front end, along the base","kind":"length","measurements":[{"id":"fde","value":0.93,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 5aa8d0d21f23 (Primary Arms, MAG532-FDE, near side view on white, 2200 x 1467)","scaleRef":"the grip's own traced side outline laid on the photo's silhouette: 267.8 px/in (logo_plate_rear_x)","method":"the tone down columns through the black lip every 0.02 in (measure.py) and the opening's corners on the resampled photo (rect/5aa-base.png, 800 px/in), turned to the strap's axis: the opening's rear edge runs along the axis 0.243 in ahead of the origin (its corner at x -0.926 y -3.655, its foot at -0.97, -3.80) and its front edge at 0.93 (the dark runs to the bottom down column -0.3 and is gone by -0.25); its upper edge is 0.192, 0.189 and 0.192 in above the outline's lowest point at columns -0.8, -0.6, -0.4, 0.180 above the bottom edge under it; the latch's top is 0.048 in under that (the dark band), its ends 0.03 to 0.04 in inside the opening's. On the user's own grip (2d8cebb209a7) the dark band is 0.05 to 0.06 in tall and the opening 0.69 long","via":"harvest"}}]},"latch_window_height":{"label":"Base: the latch's opening, its upper edge above the bottom edge","kind":"length","measurements":[{"id":"fde","value":0.18,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 5aa8d0d21f23 (Primary Arms, MAG532-FDE, near side view on white, 2200 x 1467)","scaleRef":"the grip's own traced side outline laid on the photo's silhouette: 267.8 px/in (logo_plate_rear_x)","method":"the tone down columns through the black lip every 0.02 in (measure.py) and the opening's corners on the resampled photo (rect/5aa-base.png, 800 px/in), turned to the strap's axis: the opening's rear edge runs along the axis 0.243 in ahead of the origin (its corner at x -0.926 y -3.655, its foot at -0.97, -3.80) and its front edge at 0.93 (the dark runs to the bottom down column -0.3 and is gone by -0.25); its upper edge is 0.192, 0.189 and 0.192 in above the outline's lowest point at columns -0.8, -0.6, -0.4, 0.180 above the bottom edge under it; the latch's top is 0.048 in under that (the dark band), its ends 0.03 to 0.04 in inside the opening's. On the user's own grip (2d8cebb209a7) the dark band is 0.05 to 0.06 in tall and the opening 0.69 long","via":"harvest"}}]},"latch_height":{"label":"Base: the cap's latch in its opening, its top above the bottom edge","kind":"length","measurements":[{"id":"fde","value":0.132,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 5aa8d0d21f23 (Primary Arms, MAG532-FDE, near side view on white, 2200 x 1467)","scaleRef":"the grip's own traced side outline laid on the photo's silhouette: 267.8 px/in (logo_plate_rear_x)","method":"the tone down columns through the black lip every 0.02 in (measure.py) and the opening's corners on the resampled photo (rect/5aa-base.png, 800 px/in), turned to the strap's axis: the opening's rear edge runs along the axis 0.243 in ahead of the origin (its corner at x -0.926 y -3.655, its foot at -0.97, -3.80) and its front edge at 0.93 (the dark runs to the bottom down column -0.3 and is gone by -0.25); its upper edge is 0.192, 0.189 and 0.192 in above the outline's lowest point at columns -0.8, -0.6, -0.4, 0.180 above the bottom edge under it; the latch's top is 0.048 in under that (the dark band), its ends 0.03 to 0.04 in inside the opening's. On the user's own grip (2d8cebb209a7) the dark band is 0.05 to 0.06 in tall and the opening 0.69 long","via":"harvest"}}]},"latch_end_gap":{"label":"Base: the gap between each end of the latch and its opening's","kind":"length","measurements":[{"id":"fde","value":0.035,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-moe-k2-plus 5aa8d0d21f23 (Primary Arms, MAG532-FDE, near side view on white, 2200 x 1467)","scaleRef":"the grip's own traced side outline laid on the photo's silhouette: 267.8 px/in (logo_plate_rear_x)","method":"the tone down columns through the black lip every 0.02 in (measure.py) and the opening's corners on the resampled photo (rect/5aa-base.png, 800 px/in), turned to the strap's axis: the opening's rear edge runs along the axis 0.243 in ahead of the origin (its corner at x -0.926 y -3.655, its foot at -0.97, -3.80) and its front edge at 0.93 (the dark runs to the bottom down column -0.3 and is gone by -0.25); its upper edge is 0.192, 0.189 and 0.192 in above the outline's lowest point at columns -0.8, -0.6, -0.4, 0.180 above the bottom edge under it; the latch's top is 0.048 in under that (the dark band), its ends 0.03 to 0.04 in inside the opening's. On the user's own grip (2d8cebb209a7) the dark band is 0.05 to 0.06 in tall and the opening 0.69 long","via":"harvest"}}]},"latch_window_depth":{"label":"Base: how far the latch's opening is sunk in the lip (no view shows it in profile)","kind":"length","measurements":[{"id":"assumed","value":0.05,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the opening goes through the core's wall and reads black on the user's own grip; the latch's face is drawn half of detail_relief under the lip's.","via":"harvest"}}]}}},{"subject":"magpul-moe-mlok-handguard-carbine","title":"Magpul MOE® M-LOK® Hand Guard, Carbine-Length – AR15/M4 (MAG424)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"magpul","value":6.8,"unit":"oz","stated":"Weight 6.8 oz.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE® M-LOK® Hand Guard, Carbine-Length – AR15/M4, Model MAG424: Specifications","url":"https://magpul.com/moem-lokhandguard-carbine-length-ar15-m4.html","retrieved":"2026-10-28","via":"harvest"}},{"id":"primary-arms","value":6.8,"unit":"oz","stated":"It measures 7.1\" long, 2.5\" tall, and 2.2\" wide, and weighs 6.8 oz.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Magpul MOE Drop In AR-15 Handguard - M-LOK - Carbine Length (black, MAG424-BLK)","url":"https://www.primaryarms.com/magpul-moe-m-lok-handguard-carbine-length-black","retrieved":"2026-10-28","via":"harvest"}}],"adopt":{"from":"magpul","reason":"The maker's figure; Primary Arms' page states the same."},"note":"The two halves together, the lower one with its riveted aluminium heat shield."},"length":{"label":"Length, overall","kind":"length","measurements":[{"id":"magpul","value":7.1,"unit":"in","stated":"Length, overall: 7.1 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE® M-LOK® Hand Guard, Carbine-Length – AR15/M4, Model MAG424: Specifications","url":"https://magpul.com/moem-lokhandguard-carbine-length-ar15-m4.html","retrieved":"2026-10-28","via":"harvest"}},{"id":"primary-arms","value":7.1,"unit":"in","stated":"It measures 7.1\" long, 2.5\" tall, and 2.2\" wide","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Magpul MOE Drop In AR-15 Handguard - M-LOK - Carbine Length (black, MAG424-BLK)","url":"https://www.primaryarms.com/magpul-moe-m-lok-handguard-carbine-length-black","retrieved":"2026-10-28","via":"harvest"}},{"id":"photo","value":7.14,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-carbine 7ddb0240610f (Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768)","scaleRef":"its overall length (length, 7.1 in) over the outline's 958 px: 134.93 px/in; its three M-LOK slots, 211.3 px apart for the standard's 40 mm (std.mlok.slot_pitch), give 134.2 (0.5%)","method":"the outline's x-extent (958 px, columns 96 to 1054, luminance under 230) at its three M-LOK slots' scale (134.2 px/in): its rear end to the tip of its front end","via":"harvest"}}],"adopt":{"from":"magpul","reason":"The maker's figure, which Primary Arms' page repeats; the photo, scaled by the standard's M-LOK slots and by no length of the part, agrees within 0.04 in (0.5%)."},"note":"From its rear end, which stands in the delta ring's skirt against the ring's lip, to the tip of its front end, which wraps the front sight base's rear. The photo shows the rear end too: the part is alone in it."},"mounting_length":{"label":"Length, mounting (from its rear end in the delta ring to its front flange's end in the cap)","kind":"length","measurements":[{"id":"magpul","value":6.6,"unit":"in","stated":"Length, mounting: 6.6 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE® M-LOK® Hand Guard, Carbine-Length – AR15/M4, Model MAG424: Specifications","url":"https://magpul.com/moem-lokhandguard-carbine-length-ar15-m4.html","retrieved":"2026-10-28","via":"harvest"}}],"note":"Magpul says no more than the figure. Taken as from the rear end that bears on the delta ring's lip to the front end of the front flange, which its instructions slide \"into the metal Hand Guard cap, located behind the front sight base\" (one sheet for the three lengths)."},"width":{"label":"Width","kind":"length","measurements":[{"id":"magpul","value":2.2,"unit":"in","stated":"Width 2.2 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE® M-LOK® Hand Guard, Carbine-Length – AR15/M4, Model MAG424: Specifications","url":"https://magpul.com/moem-lokhandguard-carbine-length-ar15-m4.html","retrieved":"2026-10-28","via":"harvest"}},{"id":"primary-arms","value":2.2,"unit":"in","stated":"It measures 7.1\" long, 2.5\" tall, and 2.2\" wide","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Magpul MOE Drop In AR-15 Handguard - M-LOK - Carbine Length (black, MAG424-BLK)","url":"https://www.primaryarms.com/magpul-moe-m-lok-handguard-carbine-length-black","retrieved":"2026-10-28","via":"harvest"}}],"adopt":{"from":"magpul","reason":"The maker's figure; Primary Arms' page states the same."},"note":"No view on file looks at it from above or from an end square on: drawn at Magpul's figure, which no photo checks (its height reads 5% under Magpul's in the level photo)."},"height":{"label":"Height, excluding the front lower lip","kind":"length","measurements":[{"id":"magpul","value":2.5,"unit":"in","stated":"Height, excluding lip: 2.5 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE® M-LOK® Hand Guard, Carbine-Length – AR15/M4, Model MAG424: Specifications","url":"https://magpul.com/moem-lokhandguard-carbine-length-ar15-m4.html","retrieved":"2026-10-28","via":"harvest"}},{"id":"primary-arms","value":2.5,"unit":"in","stated":"It measures 7.1\" long, 2.5\" tall, and 2.2\" wide","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Magpul MOE Drop In AR-15 Handguard - M-LOK - Carbine Length (black, MAG424-BLK)","url":"https://www.primaryarms.com/magpul-moe-m-lok-handguard-carbine-length-black","retrieved":"2026-10-28","via":"harvest"}},{"id":"photo","value":2.38,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-carbine 7ddb0240610f (Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768)","scaleRef":"its overall length (length, 7.1 in) over the outline's 958 px: 134.93 px/in; its three M-LOK slots, 211.3 px apart for the standard's 40 mm (std.mlok.slot_pitch), give 134.2 (0.5%)","method":"the body's top (row 220) to its bottom (row 540) clear of both ends and the lip (columns 165 to 900): 320 px; 2.37 at the length's scale, 2.385 at the slots'; ± 2 px","via":"harvest"}}],"adopt":{"from":"photo","reason":"The level photo, scaled by Magpul's own overall length and by the standard's M-LOK slots (the two within 0.5%), has the body 2.38 tall clear of the lip; Magpul's 2.5 is 5% more, and what it measures over isn't said (the lip reaches 2.63 in the same photo). A side view seen from a little above or below would read taller, not shorter."}},"inside_diameter":{"label":"Inside diameter","kind":"length","measurements":[],"note":"Magpul gives none. The model's inside is its outside less the wall (wall), which no view gives either."},"rear_x":{"label":"Its rear end (bearing on the delta ring's lip) ahead of the receiver's front face","kind":"length","measurements":[{"id":"derived","value":0.336,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{std.ar15.slip_ring_front_x}","via":"harvest"}}],"note":"Where the standard's delta ring holds it: its rear end in the ring's skirt, against the lip (std.ar15.slip_ring_front_x, from the Army's drawings). Its instructions: \"make sure your delta ring is securing BOTH upper and lower rear flanges of the Hand Guards\"."},"visible_rear_x":{"label":"Where its body shows ahead of the delta ring (the ring's skirt's front end), from its rear end","kind":"length","measurements":[{"id":"derived","value":0.12,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.ar15.slip_ring_skirt_length}","via":"harvest"}}],"note":"Its rear end stands in the ring's front skirt (std.ar15.slip_ring_skirt_length). The photo of it alone shows that end: two half rings, one on each half."},"top_above_axis":{"label":"Its top above the bore axis","kind":"length","measurements":[{"id":"photo","value":1.18,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-carbine 7ddb0240610f (Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768)","scaleRef":"its overall length (length, 7.1 in) over the outline's 958 px: 134.93 px/in; its three M-LOK slots, 211.3 px apart for the standard's 40 mm (std.mlok.slot_pitch), give 134.2 (0.5%)","method":"the rear end's middle (the outline's rear end, rows 337 to 421 at column 96 and 268 to 493 at 119, about the bore: row 379.5) to the body's top (row 220, the crown between its vents): 159.5 px; ± 3 px","via":"harvest"}}]},"bottom_below_axis":{"label":"Its body's bottom (clear of the lip) below the bore axis","kind":"length","measurements":[{"id":"photo","value":1.19,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-carbine 7ddb0240610f (Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768)","scaleRef":"its overall length (length, 7.1 in) over the outline's 958 px: 134.93 px/in; its three M-LOK slots, 211.3 px apart for the standard's 40 mm (std.mlok.slot_pitch), give 134.2 (0.5%)","method":"the rear end's middle (row 379.5) to the body's bottom (row 539.5, columns 165 to 900): 160 px; ± 3 px","via":"harvest"}}],"note":"The body is about centred on the bore: 1.18 above and 1.19 below."},"seam_y":{"label":"The seam between its two halves, on the sides, above the bore axis (negative below)","kind":"length","measurements":[{"id":"photo","value":-0.33,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-carbine 7ddb0240610f (Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768)","scaleRef":"its overall length (length, 7.1 in) over the outline's 958 px: 134.93 px/in; its three M-LOK slots, 211.3 px apart for the standard's 40 mm (std.mlok.slot_pitch), give 134.2 (0.5%)","method":"the dark line along its side (rows 422 to 425 at columns 300 and 450, luminance 13 to 19 between 50 above and 47 below), 44 px under the rear end's middle (row 379.5); ± 2 px","via":"harvest"}}]},"rear_collar_gap":{"label":"The gap between its two halves' rear flanges at each side (where the backdrop shows through)","kind":"length","measurements":[{"id":"photo","value":0.36,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-carbine 7ddb0240610f (Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768)","scaleRef":"its overall length (length, 7.1 in) over the outline's 958 px: 134.93 px/in; its three M-LOK slots, 211.3 px apart for the standard's 40 mm (std.mlok.slot_pitch), give 134.2 (0.5%)","method":"the backdrop seen through the rear end at columns 100 and 108: rows 365 to 413 (luminance over 240), 48 px; ± 2 px","via":"harvest"}}],"note":"The two halves' rear flanges are half rings, apart at the sides: the level photo sees the backdrop through the gap between them."},"rear_collar_gap_y":{"label":"That gap's middle above the bore axis (negative below)","kind":"length","measurements":[{"id":"photo","value":-0.07,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-carbine 7ddb0240610f (Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768)","scaleRef":"its overall length (length, 7.1 in) over the outline's 958 px: 134.93 px/in; its three M-LOK slots, 211.3 px apart for the standard's 40 mm (std.mlok.slot_pitch), give 134.2 (0.5%)","method":"the gap's middle (row 389) less the rear end's middle (row 379.5): 9.5 px under the axis; ± 2 px","via":"harvest"}}]},"reach_inside":{"label":"The room inside its M-LOK faces before what runs through it (how far an accessory's nuts may reach in)","kind":"length","measurements":[],"note":"Depends on the barrel, the gas tube and the heat shield under it, and on the wall, which no view gives: no figure, so the check reads as unmade."},"mlok_side_slots":{"label":"M-LOK slots in each upper side face (the two and ten o'clock rows)","kind":"count","measurements":[{"id":"photo","value":3,"unit":"count","source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-carbine 7ddb0240610f (Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768)","scaleRef":"none: a count","method":"three slots in the right side's row; three in the left's on Primary Arms' OD green (431dc8b3dc62) and black (8014084a9a99) photos and on Magpul's feature photos on a rifle (8e445b9aae44, 1274be34aad7); the instruction sheet draws three for each length","via":"harvest"}}]},"mlok_side_slot0_x":{"label":"The side rows' rearmost M-LOK slot (its centre), from its rear end","kind":"length","measurements":[{"id":"photo","value":1.83,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-carbine 7ddb0240610f (Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768)","scaleRef":"its overall length (length, 7.1 in) over the outline's 958 px: 134.93 px/in; its three M-LOK slots, 211.3 px apart for the standard's 40 mm (std.mlok.slot_pitch), give 134.2 (0.5%)","method":"the rearmost slot's centre (column 343.0, between its edges at 258.0 and 428.1 at luminance 25 along rows 348 to 362) less the outline's rear end (column 96): 247 px; ± 2 px. The next two at 554.2 and 765.6: 211.3 px apart, the standard's pitch","via":"harvest"}}]},"mlok_side_slot_y":{"label":"The side rows' slot centres above the bore axis","kind":"length","measurements":[{"id":"photo","value":0.16,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-carbine 7ddb0240610f (Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768)","scaleRef":"its overall length (length, 7.1 in) over the outline's 958 px: 134.93 px/in; its three M-LOK slots, 211.3 px apart for the standard's 40 mm (std.mlok.slot_pitch), give 134.2 (0.5%)","method":"each slot's edges at half the luminance step down columns 343 and 554 (rows 338.5 and 377.5): centre 358, 21.5 px over the rear end's middle (row 379.5); ± 2 px","via":"harvest"}}]},"mlok_side_face_angle":{"label":"The side M-LOK faces' outward direction about the bore axis, from straight up (degrees)","kind":"angle","measurements":[{"id":"magpul","value":60,"unit":"deg","stated":"M-LOK slots at the two, six, and ten o'clock positions","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE® M-LOK® Hand Guard, Carbine-Length – AR15/M4, Model MAG424: Specifications","url":"https://magpul.com/moem-lokhandguard-carbine-length-ar15-m4.html","retrieved":"2026-10-28","via":"harvest"}},{"id":"photo","value":78,"unit":"deg","pm":12,"source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-carbine 7ddb0240610f (Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768)","scaleRef":"its overall length (length, 7.1 in) over the outline's 958 px: 134.93 px/in; its three M-LOK slots, 211.3 px apart for the standard's 40 mm (std.mlok.slot_pitch), give 134.2 (0.5%)","method":"each slot's height in the level side view, 39 px (rows 338.5 to 377.5), against the standard's 7 mm width (std.mlok.slot_width, 37.2 px): a face no more than about 20° from upright, its slots' centres 0.16 over the axis at the side","via":"harvest"}}],"adopt":{"from":"photo","reason":"Magpul's \"two ... ten o'clock\" says which faces, not their angle: a face 60° from up would show its 7 mm slots 0.24 in tall in a level side view, and they show 0.29 in this one. The accessories on them stand out at the angle the faces have."}},"mlok_side_face_distance":{"label":"The side M-LOK faces' distance from the bore axis (along their outward direction)","kind":"length","measurements":[{"id":"derived","value":1.0462,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"({.width} / 2 - {.face_flat} / 2 * cos({.mlok_side_face_angle})) * sin({.mlok_side_face_angle}) + {.mlok_side_slot_y} * cos({.mlok_side_face_angle})","via":"harvest"}}],"note":"The face's flat runs up from the side at full width (its lower edge), leaning in at the face's angle, its middle where the photo has the slots' centres (mlok_side_slot_y): the plane through it."},"mlok_bottom_face_distance":{"label":"The underside's M-LOK face, its distance below the bore axis","kind":"length","measurements":[{"id":"derived","value":1.19,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.bottom_below_axis}","via":"harvest"}}]},"mlok_bottom_slots":{"label":"M-LOK slots in the underside (six o'clock)","kind":"count","measurements":[{"id":"assumed","value":3,"unit":"count","source":{"type":"derived","expr":"{.mlok_side_slots}","basis":"An assumption for the drawing, not a reading: Magpul's page states slots at six o'clock; no view on file looks at the underside square. Magpul's feature photo with an MVG on it (8e445b9aae44) shows one slot behind the grip and one ahead of it, the grip over a third place between them: the side rows' count and places are taken.","via":"harvest"}}]},"mlok_bottom_slot0_x":{"label":"The underside's rearmost M-LOK slot (its centre), from its rear end","kind":"length","measurements":[{"id":"assumed","value":1.83,"unit":"in","pm":0.3,"source":{"type":"derived","expr":"{.mlok_side_slot0_x}","basis":"An assumption for the drawing, not a reading: in line with the side rows (mlok_bottom_slots).","via":"harvest"}}]},"window_count":{"label":"The pockets along each side of the lower half (one in each panel between its ribs)","kind":"count","measurements":[{"id":"photo","value":4,"unit":"count","source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-carbine 7ddb0240610f (Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768)","scaleRef":"none: a count","method":"four along row 508 (dark runs at columns 252 to 763); four on Primary Arms' OD green (431dc8b3dc62) and Magpul's MVG photo (8e445b9aae44)","via":"harvest"}}]},"window0_x":{"label":"The lower half's rearmost pocket (its centre), from its rear end","kind":"length","measurements":[{"id":"photo","value":1.42,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-carbine 7ddb0240610f (Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768)","scaleRef":"its overall length (length, 7.1 in) over the outline's 958 px: 134.93 px/in; its three M-LOK slots, 211.3 px apart for the standard's 40 mm (std.mlok.slot_pitch), give 134.2 (0.5%)","method":"the dark runs along rows 503 to 513 at luminance 40: centres 287.3, 433.1, 580.0 and 727.3, the rearmost 191.3 px ahead of the rear end (column 96); ± 2 px","via":"harvest"}}]},"window_pitch":{"label":"The lower half's pockets, centre to centre","kind":"length","measurements":[{"id":"photo","value":1.09,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-carbine 7ddb0240610f (Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768)","scaleRef":"its overall length (length, 7.1 in) over the outline's 958 px: 134.93 px/in; its three M-LOK slots, 211.3 px apart for the standard's 40 mm (std.mlok.slot_pitch), give 134.2 (0.5%)","method":"three gaps between the four pockets' centres, 440 px from the first to the last: 146.7 px each","via":"harvest"}}]},"window_length":{"label":"Each pocket's length along it","kind":"length","measurements":[{"id":"photo","value":0.52,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-carbine 7ddb0240610f (Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768)","scaleRef":"its overall length (length, 7.1 in) over the outline's 958 px: 134.93 px/in; its three M-LOK slots, 211.3 px apart for the standard's 40 mm (std.mlok.slot_pitch), give 134.2 (0.5%)","method":"the four dark runs along rows 503 to 513, 70.4 to 78.3 px at luminance 40 and 70.2 to 71.5 at 36 (its ends' bevels lighter): 71 px; ± 3 px","via":"harvest"}}]},"window_y":{"label":"The pockets' centres above the bore axis (negative below)","kind":"length","measurements":[{"id":"photo","value":-0.96,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-carbine 7ddb0240610f (Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768)","scaleRef":"its overall length (length, 7.1 in) over the outline's 958 px: 134.93 px/in; its three M-LOK slots, 211.3 px apart for the standard's 40 mm (std.mlok.slot_pitch), give 134.2 (0.5%)","method":"the pockets' dark rows 500 to 517 at columns 300 and 450 (luminance 24 to 39 between 57 above and 46 below): centre 508.5, 129 px under the rear end's middle (row 379.5); ± 2 px","via":"harvest"}}]},"window_height":{"label":"Each pocket's height","kind":"length","measurements":[{"id":"photo","value":0.13,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-carbine 7ddb0240610f (Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768)","scaleRef":"its overall length (length, 7.1 in) over the outline's 958 px: 134.93 px/in; its three M-LOK slots, 211.3 px apart for the standard's 40 mm (std.mlok.slot_pitch), give 134.2 (0.5%)","method":"the same dark rows, 500 to 517: 17 px; ± 2 px. The level photo of a black one shows each pocket whole","via":"harvest"}}]},"vent_count":{"label":"The vents along its crown","kind":"count","measurements":[{"id":"photo","value":4,"unit":"count","source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-carbine 7ddb0240610f (Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768)","scaleRef":"none: a count","method":"four dips in the top of the level outline, where the vents cut the crown's line; four rounded slots along the top in Magpul's Stealth Gray shot (ebf5bc6f3e4d) and Primary Arms' black one from above (8014084a9a99)","via":"harvest"}}]},"vent0_x":{"label":"The rearmost vent's middle, from its rear end","kind":"length","measurements":[{"id":"photo","value":2.03,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-carbine 7ddb0240610f (Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768)","scaleRef":"its overall length (length, 7.1 in) over the outline's 958 px: 134.93 px/in","method":"the traced outline's top: dips 0.037 in deep from 1.764 to 2.296, 2.888 to 3.465, 4.034 to 4.604 and 5.203 to 5.750; the rearmost's middle","via":"harvest"}}]},"vent_pitch":{"label":"The vents, middle to middle","kind":"length","measurements":[{"id":"photo","value":1.15,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-carbine 7ddb0240610f (Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768)","scaleRef":"134.93 px/in","method":"the four dips' middles, 2.03, 3.18, 4.32 and 5.48: 3.45 in over three gaps","via":"harvest"}}]},"vent_length":{"label":"Each vent's length along it","kind":"length","measurements":[{"id":"photo","value":0.55,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-carbine 7ddb0240610f (Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768)","scaleRef":"134.93 px/in","method":"the four dips' lengths, 0.532 to 0.577: the vents' ends where they meet the crown's line","via":"harvest"}}]},"vent_width":{"label":"Each vent's width across the crown","kind":"length","measurements":[{"id":"assumed","value":0.16,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view looks down on the crown square; in the three-quarter shots each vent is about a quarter as wide as long, foreshortened by an angle the photo doesn't give.","via":"harvest"}}]},"panel_rib":{"label":"The ribs between the lower half's panels (and round them), their width","kind":"length","measurements":[{"id":"assumed","value":0.12,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the ribs show as lit and shaded lines a few pixels wide between the pockets in the photos on file, their width and how far they stand on no view in section.","via":"harvest"}}]},"panel_depth":{"label":"How far the lower half's panels stand in from its ribs","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the panels' edges catch the light in the three-quarter photos, how deep they are isn't seen in profile.","via":"harvest"}}]},"window_depth":{"label":"Each pocket's depth into the wall","kind":"length","measurements":[{"id":"assumed","value":0.06,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows a pocket in section; they aren't through (Primary Arms' OD green one, 431dc8b3dc62, shows its own colour in them, not the backdrop).","via":"harvest"}}]},"wall":{"label":"Its polymer wall's thickness","kind":"length","measurements":[{"id":"assumed","value":0.15,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows an end square on or a section. The mid-length's assumption, one moulding of one maker's (at 0.1 in that model was 38% under Magpul's weight at the polymer's density on file); checked here against Magpul's 6.8 oz for this one (its test). What the model lacks is the inner ribs and bosses no view shows.","via":"harvest"}}]},"heat_shield_thickness":{"label":"Its aluminium heat shield's thickness","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the shield shows only through the slots and at the open front end, never in section.","via":"harvest"}}]},"seam_groove":{"label":"The seam's groove along each side (its width and its depth)","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the seam shows as a dark line three or four pixels wide at 135 px to the inch in the level photo (0.02 to 0.03 in), its depth on no view.","via":"harvest"}}]},"face_flat":{"label":"Each upper side face's flat (where its M-LOK slots are), its height across the face","kind":"length","measurements":[{"id":"assumed","value":0.62,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the slot's 7 mm and a margin each side as wide as the slots' 8 mm webs, which is how Primary Arms' black one (8014084a9a99) shows the raised band round its slots.","via":"harvest"}}]},"top_half_width":{"label":"Its top's flat (the crown, between the upper side faces' rounds), half its width","kind":"length","measurements":[{"id":"assumed","value":0.5,"unit":"in","pm":0.15,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no end view on file; Primary Arms' three-quarter photos (8014084a9a99, 431dc8b3dc62) show a rounded crown about as wide as the bore's two sides above the faces.","via":"harvest"}}]},"bottom_half_width":{"label":"Its underside's flat (where the six o'clock slots are), half its width","kind":"length","measurements":[{"id":"assumed","value":0.45,"unit":"in","pm":0.15,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file looks at the underside; Magpul's feature photo with its MVG on (8e445b9aae44) shows a flat underside a little narrower than the grip's base, rounding into the sides.","via":"harvest"}}]},"front_flange_od":{"label":"Its front flange (what goes into the hand guard cap), outside diameter","kind":"length","measurements":[{"id":"assumed","value":1.36,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the flange goes \"into the metal Hand Guard cap\" (its instructions) and Magpul says it takes a round or a triangular cap; no view shows it but end-on from the front (Primary Arms' OD green one, 431dc8b3dc62: an arc inside the body). Taken inside both caps on file: the triangular cap's sides stand 0.689 from the axis inside at their middles (bcm-handguard-cap-triangle-750: side_r less side_centre_r less the sheet), the round cap's two tabs at 3 and 9 o'clock to 0.690.","via":"harvest"}}]},"front_flange_length":{"label":"Its front flange's length (into the cap)","kind":"length","measurements":[{"id":"assumed","value":0.42,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view shows the flange from the side. Long enough that the front wall it stands from stays behind either cap's rim with the flange home (the round cap is 0.276 deep, the triangular 0.323).","via":"harvest"}}]},"rear_collar_od":{"label":"Its rear end (what stands in the delta ring's skirt), outside diameter","kind":"length","measurements":[{"id":"assumed","value":1.72,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: its rear end stands in the delta ring's skirt (std.ar15.slip_ring_skirt_d, 1.750 inside) and shows on no photo; taken 0.03 under the skirt.","via":"harvest"}}]},"front_wall_x":{"label":"Its front wall (the inner face the front flange stands from), from its rear end","kind":"length","measurements":[{"id":"derived","value":6.03,"unit":"in","pm":0.12,"source":{"type":"derived","expr":"{.mounting_length} - {.front_flange_length} - {.wall}","via":"harvest"}}],"note":"Ahead of the wall the shell runs on open to its front tip, over the cap and the front sight base's rear (\"Hand guard will wrap around the front sight when mounted\")."}}},{"subject":"magpul-moe-mlok-handguard-mid","title":"Magpul MOE® M-LOK® Hand Guard, Mid-Length – AR15/M4 (MAG426)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"magpul","value":8.7,"unit":"oz","stated":"Weight 8.7 oz.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE® M-LOK® Hand Guard, Mid-Length – AR15/M4, Model MAG426: Specifications","url":"https://magpul.com/moem-lokhandguard-mid-length-ar15-m4.html","retrieved":"2026-10-28","via":"harvest"}},{"id":"primary-arms","value":8.7,"unit":"oz","stated":"It measures 9.2\" long, 2.5\" tall, and 2.2\" wide, and weighs 8.7 oz.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Magpul MOE Drop In AR-15 Handguard - M-LOK - Mid-Length (black, MAG426-BLK)","url":"https://www.primaryarms.com/magpul-moe-m-lok-handguard-mid-length-black-mag426-blk","retrieved":"2026-10-28","via":"harvest"}}],"adopt":{"from":"magpul","reason":"The maker's figure; Primary Arms' page states the same."},"note":"The two halves together, the lower one with its riveted aluminium heat shield."},"length":{"label":"Length, overall","kind":"length","measurements":[{"id":"magpul","value":9.2,"unit":"in","stated":"Length, overall: 9.2 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE® M-LOK® Hand Guard, Mid-Length – AR15/M4, Model MAG426: Specifications","url":"https://magpul.com/moem-lokhandguard-mid-length-ar15-m4.html","retrieved":"2026-10-28","via":"harvest"}},{"id":"primary-arms","value":9.2,"unit":"in","stated":"It measures 9.2\" long, 2.5\" tall, and 2.2\" wide","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Magpul MOE Drop In AR-15 Handguard - M-LOK - Mid-Length (black, MAG426-BLK)","url":"https://www.primaryarms.com/magpul-moe-m-lok-handguard-mid-length-black-mag426-blk","retrieved":"2026-10-28","via":"harvest"}}],"adopt":{"from":"magpul","reason":"The maker's figure; Primary Arms' page states the same."},"note":"From its rear end, which stands in the delta ring's skirt against the ring's lip, to the tip of its front end, which wraps the front sight base's rear."},"mounting_length":{"label":"Length, mounting (from its rear end in the delta ring to its front flange's end in the cap)","kind":"length","measurements":[{"id":"magpul","value":8.6,"unit":"in","stated":"Length, mounting: 8.6 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE® M-LOK® Hand Guard, Mid-Length – AR15/M4, Model MAG426: Specifications","url":"https://magpul.com/moem-lokhandguard-mid-length-ar15-m4.html","retrieved":"2026-10-28","via":"harvest"}}],"note":"Magpul says no more than the figure. Taken here as from the rear end that bears on the delta ring's lip to the front end of the front flange, which its instructions slide \"into the metal Hand Guard cap, located behind the front sight base\": the length a rifle's ring and cap have to hold it between. The overall length runs 0.6 in further, over the cap and the front sight base's rear."},"width":{"label":"Width","kind":"length","measurements":[{"id":"magpul","value":2.2,"unit":"in","stated":"Width 2.2 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE® M-LOK® Hand Guard, Mid-Length – AR15/M4, Model MAG426: Specifications","url":"https://magpul.com/moem-lokhandguard-mid-length-ar15-m4.html","retrieved":"2026-10-28","via":"harvest"}},{"id":"primary-arms","value":2.2,"unit":"in","stated":"It measures 9.2\" long, 2.5\" tall, and 2.2\" wide","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Magpul MOE Drop In AR-15 Handguard - M-LOK - Mid-Length (black, MAG426-BLK)","url":"https://www.primaryarms.com/magpul-moe-m-lok-handguard-mid-length-black-mag426-blk","retrieved":"2026-10-28","via":"harvest"}}],"adopt":{"from":"magpul","reason":"The maker's figure; Primary Arms' page states the same."},"note":"No view on file looks at it from above or from an end square on, so the width isn't read on a photo: the height Magpul gives reads 6% more than its photo does (height), and its width may say as much more than the part is. Drawn at Magpul's figure."},"height":{"label":"Height, excluding the front lower lip","kind":"length","measurements":[{"id":"magpul","value":2.5,"unit":"in","stated":"Height, excluding lip: 2.5 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE® M-LOK® Hand Guard, Mid-Length – AR15/M4, Model MAG426: Specifications","url":"https://magpul.com/moem-lokhandguard-mid-length-ar15-m4.html","retrieved":"2026-10-28","via":"harvest"}},{"id":"primary-arms","value":2.5,"unit":"in","stated":"It measures 9.2\" long, 2.5\" tall, and 2.2\" wide","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Magpul MOE Drop In AR-15 Handguard - M-LOK - Mid-Length (black, MAG426-BLK)","url":"https://www.primaryarms.com/magpul-moe-m-lok-handguard-mid-length-black-mag426-blk","retrieved":"2026-10-28","via":"harvest"}},{"id":"photo","value":2.34,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-mid 6dbfde278bf7 (Magpul's feature image 03 for MAG426: the OD green hand guard on a rifle with an A2 front sight, the rifle's right side seen level, 700 x 525)","scaleRef":"its three M-LOK slots: centres 64.29 px apart (two pitches of 128.6 px) for the standard's 40 mm (std.mlok.slot_pitch), 40.82 px/in; their length, 51.9 px, for the standard's 32 mm (std.mlok.slot_length), 41.2 px/in; and the visible length (visible_length) at 40.86 px/in","method":"the body's top (row 151.5) to its bottom (row 247.0) over the length clear of both ends and the lip (columns 165 to 465, the outline at saturation > 0.18): 95.5 px at the visible length's 40.86 px/in; ± 1.5 px. The traced outline's straight runs, each taken at the middle of its pixel stair, give 2.32 (the model's)","via":"harvest"}},{"id":"carbine-photo","value":2.38,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-carbine 7ddb0240610f (Primary Arms' gallery for the black MAG424, its right side seen level, alone on white, 1152 x 768)","scaleRef":"its own three M-LOK slots, 211.3 px apart for the standard's 40 mm (134.2 px/in), which put its overall length at 7.14 for Magpul's 7.1","method":"the body's top to its bottom clear of the lip, 320 px: the carbine-length guard, the same section by every photo of the two","via":"harvest"}}],"adopt":{"from":"photo","reason":"Two photos, each scaled by its own M-LOK slots at the standard's pitch (and the carbine's also by Magpul's overall length, within 0.5%), give 2.34 and 2.38 for the body's height clear of the lip; Magpul's 2.5 is 6% more, and what it measures over isn't said (the lip reaches 2.57 in the same photo). A side view seen from a little above or below would read taller, not shorter. The model is the traced outline, at the photo's height."}},"inside_diameter":{"label":"Inside diameter","kind":"length","measurements":[],"note":"Magpul gives none: the room inside it isn't published. The model's inside is its outside less the wall (wall), which no view gives either."},"rear_x":{"label":"Its rear end (bearing on the delta ring's lip) ahead of the receiver's front face","kind":"length","measurements":[{"id":"derived","value":0.336,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{std.ar15.slip_ring_front_x}","via":"harvest"}}],"note":"Where the standard's delta ring holds it: its rear end in the ring's skirt, against the lip (std.ar15.slip_ring_front_x, from the Army's drawings). Its instructions: \"make sure your delta ring is securing BOTH upper and lower rear flanges of the Hand Guards\"."},"visible_rear_x":{"label":"Where its body shows ahead of the delta ring (the ring's skirt's front end), from its rear end","kind":"length","measurements":[{"id":"derived","value":0.12,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.ar15.slip_ring_skirt_length}","via":"harvest"}}],"note":"Its rear end stands in the ring's front skirt (std.ar15.slip_ring_skirt_length): the outline traced on the rifle begins where the skirt ends."},"visible_length":{"label":"Its length seen ahead of the delta ring (to the tip of its front end)","kind":"length","measurements":[{"id":"derived","value":9.08,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{.length} - {.visible_rear_x}","via":"harvest"}},{"id":"photo","value":9.11,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-mid 6dbfde278bf7 (Magpul's feature image 03 for MAG426: the OD green hand guard on a rifle with an A2 front sight, the rifle's right side seen level, 700 x 525)","scaleRef":"its three M-LOK slots, centres 64.29 px apart for the standard's 40 mm (std.mlok.slot_pitch): 40.82 px/in","method":"the outline at saturation > 0.18 (the delta ring and the front sight left out), from its rear edge at the ring's front (column 140.5) to its front tip (511.5): 371 px; ± 1.5 px","via":"harvest"}}],"adopt":{"from":"derived","reason":"Magpul's overall length less the standard's skirt: the photo, scaled by the standard's M-LOK slots and not by any length of the part, agrees within 0.03 in (0.3%)."}},"top_above_axis":{"label":"Its top above the bore axis","kind":"length","measurements":[{"id":"photo","value":1.15,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-mid 6dbfde278bf7 (Magpul's feature image 03 for MAG426: the OD green hand guard on a rifle with an A2 front sight, the rifle's right side seen level, 700 x 525)","scaleRef":"visible_length, 9.08 in over 371 px: 40.86 px/in (the M-LOK slots give 40.82)","method":"the barrel's axis ahead of the front sight (its silhouette rows 186.5 to 210.5 from column 580 to 695, level: centre 198.5) to the body's top (row 151.5): 47 px; ± 1.5 px","via":"harvest"}}]},"bottom_below_axis":{"label":"Its body's bottom (clear of the lip) below the bore axis","kind":"length","measurements":[{"id":"photo","value":1.19,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-mid 6dbfde278bf7 (Magpul's feature image 03 for MAG426: the OD green hand guard on a rifle with an A2 front sight, the rifle's right side seen level, 700 x 525)","scaleRef":"visible_length, 9.08 in over 371 px: 40.86 px/in","method":"the barrel's axis (row 198.5) to the body's bottom (row 247.0, columns 165 to 465): 48.5 px; ± 1.5 px","via":"harvest"}}],"note":"The body is near centred on the bore: 1.15 above and 1.19 below."},"seam_y":{"label":"The seam between its two halves, on the sides, above the bore axis (negative below)","kind":"length","measurements":[{"id":"photo","value":-0.245,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-mid 6dbfde278bf7 (Magpul's feature image 03 for MAG426: the OD green hand guard on a rifle with an A2 front sight, the rifle's right side seen level, 700 x 525)","scaleRef":"visible_length: 40.86 px/in","method":"the dark line along its side (rows 208 to 209 at columns 230 and 260, luminance 93 to 105 between 124 above and 110 below), 10 px under the axis (row 198.5); ± 1 px","via":"harvest"}}],"note":"The upper half reaches below the axis; the lower one slides into it (its instructions' step 3) and its edge stands over the upper's along the seam."},"reach_inside":{"label":"The room inside its M-LOK faces before what runs through it (how far an accessory's nuts may reach in)","kind":"length","measurements":[],"note":"Depends on the barrel, the gas tube and the heat shield under it, and on the wall, which no view gives: no figure, so the check reads as unmade."},"mlok_side_slots":{"label":"M-LOK slots in each upper side face (the two and ten o'clock rows)","kind":"count","measurements":[{"id":"photo","value":3,"unit":"count","source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-mid 6dbfde278bf7 (Magpul's feature image 03, the OD green on a rifle, its right side)","scaleRef":"none: a count","method":"three slots in the right side's row; three in the left's on Primary Arms' black (41a80c61cadb) and Flat Dark Earth (59d61863c88f) photos and on Magpul's gray on a rifle (32f412d17d79); the instruction sheet draws three for each length","via":"harvest"}}]},"mlok_side_slot0_x":{"label":"The side rows' rearmost M-LOK slot (its centre), from its rear end","kind":"length","measurements":[{"id":"photo","value":3.91,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-mid 6dbfde278bf7 (Magpul's feature image 03, the OD green on a rifle, its right side seen level, 700 x 525)","scaleRef":"visible_length: 40.86 px/in","method":"the rearmost slot's centre (column 295.5, between its edges at 269.5 and 321.6 at half the luminance step) less the outline's rear edge (140.5): 155 px = 3.79 in, plus the skirt the rear end stands in (visible_rear_x, 0.12); ± 1.5 px. The next two at 359.9 and 424.1: 64.3 px apart, the standard's pitch","via":"harvest"}}]},"mlok_side_slot_y":{"label":"The side rows' slot centres above the bore axis","kind":"length","measurements":[{"id":"photo","value":0.22,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-mid 6dbfde278bf7 (Magpul's feature image 03, the OD green on a rifle, its right side seen level, 700 x 525)","scaleRef":"visible_length: 40.86 px/in","method":"each slot's edges at half the luminance step down its middle column (rows 183.8 and 195.3 at columns 295, 360 and 424): centre 189.5, 9 px over the axis (row 198.5); ± 1 px","via":"harvest"}}]},"mlok_side_face_angle":{"label":"The side M-LOK faces' outward direction about the bore axis, from straight up (degrees)","kind":"angle","measurements":[{"id":"magpul","value":60,"unit":"deg","stated":"M-LOK slots at the two, six, and ten o'clock positions","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE® M-LOK® Hand Guard, Mid-Length – AR15/M4, Model MAG426: Specifications","url":"https://magpul.com/moem-lokhandguard-mid-length-ar15-m4.html","retrieved":"2026-10-28","via":"harvest"}},{"id":"photo","value":78,"unit":"deg","pm":10,"source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-mid 6dbfde278bf7 (Magpul's feature image 03, the OD green on a rifle, its right side seen level, 700 x 525)","scaleRef":"visible_length: 40.86 px/in","method":"each slot's height in the level side view, 11.5 px (rows 183.8 to 195.3), against the standard's 7 mm width (std.mlok.slot_width, 11.26 px): a face that leans no more than about 20° from upright (cos ≥ 0.93 at ± 1 px), and its slot's centre 0.22 above the axis at the side: about two and a half o'clock","via":"harvest"}}],"adopt":{"from":"photo","reason":"Magpul's \"two ... ten o'clock\" says which faces, not their angle: a face 60° from up would show its 7 mm slots 0.24 in tall in a level side view, and they show 0.28 (11.5 px) in Magpul's own photo, the slot's centre a fifth of an inch over the axis. The accessories on them stand out at the angle the faces have."}},"mlok_side_face_distance":{"label":"The side M-LOK faces' distance from the bore axis (along their outward direction)","kind":"length","measurements":[{"id":"derived","value":1.0587,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"({.width} / 2 - {.face_flat} / 2 * cos({.mlok_side_face_angle})) * sin({.mlok_side_face_angle}) + {.mlok_side_slot_y} * cos({.mlok_side_face_angle})","via":"harvest"}}],"note":"The face's flat runs up from the side at full width (its lower edge), leaning in at the face's angle, its middle where the photo has the slots' centres (mlok_side_slot_y): the plane through it. As good as the width and the face's angle, which no view gives square."},"mlok_bottom_face_distance":{"label":"The underside's M-LOK face, its distance below the bore axis","kind":"length","measurements":[{"id":"derived","value":1.19,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.bottom_below_axis}","via":"harvest"}}]},"mlok_bottom_slots":{"label":"M-LOK slots in the underside (six o'clock)","kind":"count","measurements":[{"id":"assumed","value":3,"unit":"count","source":{"type":"derived","expr":"{.mlok_side_slots}","basis":"An assumption for the drawing, not a reading: Magpul's page states slots at six o'clock; no view on file looks at the underside (Magpul's photo of the Flat Dark Earth one held at the hip, 4fc9580bdc8e, sees the bottom face edge-on, its slots as dark marks that aren't countable). The side rows' count, and their places, are taken.","via":"harvest"}}]},"mlok_bottom_slot0_x":{"label":"The underside's rearmost M-LOK slot (its centre), from its rear end","kind":"length","measurements":[{"id":"assumed","value":3.91,"unit":"in","pm":0.5,"source":{"type":"derived","expr":"{.mlok_side_slot0_x}","basis":"An assumption for the drawing, not a reading: in line with the side rows (mlok_bottom_slots).","via":"harvest"}}]},"window_count":{"label":"The pockets along each side of the lower half (one in each panel between its ribs)","kind":"count","measurements":[{"id":"photo","value":6,"unit":"count","source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-mid 6dbfde278bf7 (Magpul's feature image 03, the OD green on a rifle, its right side)","scaleRef":"none: a count","method":"six along row 233 (dark runs at columns 175 to 426); six on Magpul's gray on a rifle (32f412d17d79) and on Primary Arms' black (41a80c61cadb)","via":"harvest"}}]},"window0_x":{"label":"The lower half's rearmost pocket (its centre), from its rear end","kind":"length","measurements":[{"id":"photo","value":1.38,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-mid 6dbfde278bf7 (Magpul's feature image 03, the OD green on a rifle, its right side seen level, 700 x 525)","scaleRef":"visible_length: 40.86 px/in","method":"the dark runs along row 233 (each pocket's shaded upper edge): centres at 187.9, 233.0, 277.9, 323.1, 367.8 and 412.6, the rearmost 47.4 px ahead of the outline's rear edge (140.5) = 1.16, plus the skirt (visible_rear_x, 0.12); ± 1.5 px","via":"harvest"}}]},"window_pitch":{"label":"The lower half's pockets, centre to centre","kind":"length","measurements":[{"id":"photo","value":1.1,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-mid 6dbfde278bf7 (Magpul's feature image 03, the OD green on a rifle, its right side seen level, 700 x 525)","scaleRef":"visible_length: 40.86 px/in","method":"five gaps between the six pockets' centres, 224.7 px from the first to the last: 44.94 px each","via":"harvest"}}]},"window_length":{"label":"Each pocket's length along it","kind":"length","measurements":[{"id":"photo","value":0.63,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-mid 6dbfde278bf7 (Magpul's feature image 03, the OD green on a rifle, its right side seen level, 700 x 525)","scaleRef":"visible_length: 40.86 px/in","method":"the six dark runs along row 233, 25.1 to 26.4 px (mean 25.7); ± 1 px","via":"harvest"}}]},"window_y":{"label":"The pockets' centres above the bore axis (negative below)","kind":"length","measurements":[{"id":"photo","value":-0.85,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-mid 6dbfde278bf7 (Magpul's feature image 03, the OD green on a rifle, its right side seen level, 700 x 525)","scaleRef":"visible_length: 40.86 px/in","method":"the pockets' shaded edge at row 233 (luminance 53 between 86 and 89), 34.5 px under the axis (row 198.5); ± 1.5 px","via":"harvest"}}]},"window_height":{"label":"Each pocket's height","kind":"length","measurements":[{"id":"assumed","value":0.13,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the level side view shows only each pocket's shaded upper wall (3 px); Primary Arms' black one from the front and above (41a80c61cadb) draws them about a fifth as tall as long.","via":"harvest"}}]},"vent_count":{"label":"The vents along its crown","kind":"count","measurements":[{"id":"photo","value":6,"unit":"count","source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-mid c2c6b8e46059 (Magpul's gallery, the Stealth Gray MAG426 alone from above its right side and behind, 800 x 800)","scaleRef":"none: a count","method":"six rounded slots along the top; six on the black (07350227f7db), Flat Dark Earth (b6a0330a8c69) and OD green (60dc2d9c87c2) shots of the same pose, and the instruction sheet's drawing of the mid-length","via":"harvest"}}]},"vent0_x":{"label":"The rearmost vent's middle, from its rear end","kind":"length","measurements":[{"id":"photo","value":2.25,"unit":"in","pm":0.15,"source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-mid c2c6b8e46059 (Magpul's gallery, the Stealth Gray MAG426 alone from above its right side and behind, 800 x 800)","scaleRef":"its three right side M-LOK slots in the same photo (columns 302, 410 and 526) at their places in the ledger (mlok_side_slot0_x and the standard's pitch): 0.0146 in a column at the rear, 0.0136 at the front","method":"the vents' middles along the crown, columns 188, 262, 338, 420, 504 and 594 (by eye on a crop at 2.5 times), carried along the axis by the slots' columns: 2.25, 3.33, 4.43, 5.55, 6.76, 7.94. The crown stands above and inside the side face, a view from above and behind moves it along by an amount the photo doesn't give: the ±","via":"harvest"}}]},"vent_pitch":{"label":"The vents, middle to middle","kind":"length","measurements":[{"id":"photo","value":1.14,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-mid c2c6b8e46059 (Magpul's gallery, the Stealth Gray MAG426 alone from above its right side and behind, 800 x 800)","scaleRef":"the same slots' columns","method":"the first and the last vent's places, 5.69 in apart over five gaps","via":"harvest"}}]},"vent_length":{"label":"Each vent's length along it","kind":"length","measurements":[{"id":"photo","value":0.65,"unit":"in","pm":0.1,"source":{"type":"photo","photo":"references/magpul-moe-mlok-handguard-mid c2c6b8e46059 (Magpul's gallery, the Stealth Gray MAG426 alone from above its right side and behind, 800 x 800)","scaleRef":"the same slots' columns (about 69 px to the inch along the axis there)","method":"each vent 44 to 52 columns long (by eye on the crop)","via":"harvest"}}]},"vent_width":{"label":"Each vent's width across the crown","kind":"length","measurements":[{"id":"assumed","value":0.16,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view looks down on the crown square; in the three-quarter shots each vent is about a quarter as wide as long, foreshortened by an angle the photo doesn't give.","via":"harvest"}}]},"panel_rib":{"label":"The ribs between the lower half's panels (and round them), their width","kind":"length","measurements":[{"id":"assumed","value":0.12,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the ribs show as lit and shaded lines a few pixels wide between the pockets in the photos on file, their width and how far they stand on no view in section.","via":"harvest"}}]},"panel_depth":{"label":"How far the lower half's panels stand in from its ribs","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the panels' edges catch the light in the three-quarter photos, how deep they are isn't seen in profile.","via":"harvest"}}]},"window_depth":{"label":"Each pocket's depth into the wall","kind":"length","measurements":[{"id":"assumed","value":0.06,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows a pocket in section; they aren't through (the OD green one's show its own colour, not the barrel).","via":"harvest"}}]},"wall":{"label":"Its polymer wall's thickness","kind":"length","measurements":[{"id":"assumed","value":0.15,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows an end square on or a section. Taken so that the model comes near Magpul's 8.7 oz at the polymer's density on file (std.density.polymer, an unfilled nylon) with its aluminium heat shield: at 0.1 in it was 38% light. What it still lacks is the inner ribs and bosses no view shows.","via":"harvest"}}]},"heat_shield_thickness":{"label":"Its aluminium heat shield's thickness","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the shield shows only through the slots and at the open front end, never in section.","via":"harvest"}}]},"seam_groove":{"label":"The seam's groove along each side (its width and its depth)","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the seam shows as a dark line one or two pixels wide at 41 px to the inch (0.025 to 0.05 in), its depth on no view.","via":"harvest"}}]},"face_flat":{"label":"Each upper side face's flat (where its M-LOK slots are), its height across the face","kind":"length","measurements":[{"id":"assumed","value":0.62,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the slot's 7 mm and a margin each side as wide as the slots' 8 mm webs, which is how Primary Arms' black one (41a80c61cadb) shows the raised band round its slots.","via":"harvest"}}]},"top_half_width":{"label":"Its top's flat (the crown, between the upper side faces' rounds), half its width","kind":"length","measurements":[{"id":"assumed","value":0.5,"unit":"in","pm":0.15,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no end view on file; the three-quarter photos (41a80c61cadb, 431dc8b3dc62 of the carbine) show a rounded crown about as wide as the bore's two sides above the faces.","via":"harvest"}}]},"bottom_half_width":{"label":"Its underside's flat (where the six o'clock slots are), half its width","kind":"length","measurements":[{"id":"assumed","value":0.45,"unit":"in","pm":0.15,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file looks at the underside; Magpul's carbine with its MVG on (8e445b9aae44) shows a flat underside a little narrower than the grip's base, rounding into the sides.","via":"harvest"}}]},"front_flange_od":{"label":"Its front flange (what goes into the hand guard cap), outside diameter","kind":"length","measurements":[{"id":"assumed","value":1.36,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the flange goes \"into the metal Hand Guard cap\" (its instructions) and Magpul says it takes a round or a triangular cap; no view shows it but end-on from the front (the carbine's 431dc8b3dc62: an arc inside the body). Taken inside both caps on file: the triangular cap's sides stand 0.689 from the axis inside at their middles (bcm-handguard-cap-triangle-750: side_r less side_centre_r less the sheet), the round cap's two tabs at 3 and 9 o'clock to 0.690.","via":"harvest"}}]},"front_flange_length":{"label":"Its front flange's length (into the cap)","kind":"length","measurements":[{"id":"assumed","value":0.42,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view shows the flange from the side. Long enough that the front wall it stands from stays behind either cap's rim with the flange home (the round cap is 0.276 deep, the triangular 0.323).","via":"harvest"}}]},"rear_collar_od":{"label":"Its rear end (what stands in the delta ring's skirt), outside diameter","kind":"length","measurements":[{"id":"assumed","value":1.72,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: its rear end stands in the delta ring's skirt (std.ar15.slip_ring_skirt_d, 1.750 inside) and shows on no photo; taken 0.03 under the skirt.","via":"harvest"}}]},"front_wall_x":{"label":"Its front wall (the inner face the front flange stands from), from its rear end","kind":"length","measurements":[{"id":"derived","value":8.03,"unit":"in","pm":0.12,"source":{"type":"derived","expr":"{.mounting_length} - {.front_flange_length} - {.wall}","via":"harvest"}}],"note":"Ahead of the wall the shell runs on open to its front tip, over the cap and the front sight base's rear (\"Hand guard will wrap around the front sight when mounted\")."}}},{"subject":"magpul-moe-plus","title":"Magpul MOE+ grip (MAG416)","dimensions":{"grip_angle":{"label":"Grip angle (the straps' lean from vertical, installed)","kind":"angle","measurements":[{"id":"magpul","value":25,"unit":"deg","stated":"Grip Angle 25 degrees","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE+ Grip - AR15/M4 (MAG416)","url":"https://magpul.com/moe-plus-grip-ar15-m4.html","retrieved":"2026-10-01","via":"harvest"},"note":"Magpul doesn't say which line the angle is measured on: \"Traditional 25-degree grip angle familiar to AR-15 shooters\"."},{"id":"aero-right","value":26.282,"unit":"deg","pm":1.377,"source":{"type":"photo","photo":"references/magpul-moe-plus d86458936f6f (Aero Precision APAR501124: a complete lower with the plain MOE, straight right side, 1000 x 1000)","scaleRef":"frame from the reviewed holes takedown, pivot, selector, hammer, trigger (63.7 px/in, rms 0.012 in over 5 points)","method":"mean lean of the fitted profile's edges in the band 0.45–0.85 of its height (rear 27.6°, front 25.0°) of the traced outline (tools/trace.py); the straps' mean lean (band 0.45–0.85 of the height) once fitted to the installed grip","via":"harvest"}},{"id":"aero-left","value":26.202,"unit":"deg","pm":1.377,"source":{"type":"photo","photo":"references/magpul-moe-plus ffa403d63b08 (Aero Precision APAR501124: a complete lower with the plain MOE, straight left side, 1000 x 630)","scaleRef":"frame from the reviewed holes takedown, pivot, selector, hammer, trigger (63.3 px/in, rms 0.019 in over 5 points)","method":"mean lean of the fitted profile's edges in the band 0.45–0.85 of its height (rear 27.5°, front 24.9°) of the traced outline (tools/trace.py); the straps' mean lean (band 0.45–0.85 of the height) once fitted to the installed grip","via":"harvest"}}],"adopt":{"from":"aero-right","reason":"The straps' lean on a grip seated on a lower, from two pin-framed photos that agree within 0.1°. Magpul's figure fits the front strap alone."},"note":"The mean of the back and front straps' lean with the flat top level. Magpul's 25 degrees is the front strap's (24.9 to 25.0 in both fits); the back strap leans 27.5."},"receiver_to_bottom":{"label":"\"Height, receiver to bottom\" (Magpul)","kind":"length","measurements":[{"id":"magpul","value":4,"unit":"in","pm":0.05,"stated":"Height, receiver to bottom 4.0 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE+ Grip - AR15/M4 (MAG416)","url":"https://magpul.com/moe-plus-grip-ar15-m4.html","retrieved":"2026-10-01","via":"harvest"}}]},"toe_below_pin_line":{"label":"Grip's lowest point below the pin line, installed (the plain MOE on Aero's complete lower)","kind":"length","measurements":[{"id":"aero-right","value":5.016,"unit":"in","pm":0.031,"source":{"type":"photo","photo":"references/magpul-moe-plus d86458936f6f (Aero Precision APAR501124: a complete lower with the plain MOE, straight right side, 1000 x 1000)","scaleRef":"frame from the reviewed holes takedown, pivot, selector, hammer, trigger (63.7 px/in, rms 0.012 in over 5 points)","method":"−y_min in x [-2.6, 1.0] of the traced outline (tools/trace.py); the grip's lowest point (its toe, at the front of the cap)","via":"harvest"}},{"id":"aero-left","value":5.13,"unit":"in","pm":0.034,"source":{"type":"photo","photo":"references/magpul-moe-plus ffa403d63b08 (Aero Precision APAR501124: a complete lower with the plain MOE, straight left side, 1000 x 630)","scaleRef":"frame from the reviewed holes takedown, pivot, selector, hammer, trigger (63.3 px/in, rms 0.019 in over 5 points)","method":"−y_min in x [-2.6, 1.0] of the traced outline (tools/trace.py); the grip's lowest point (its toe, at the front of the cap)","via":"harvest"}}],"adopt":{"from":"aero-left","reason":"With the grip's flat top on the receiver's underside (1.072 below the pins: bad-workhorse-lower.grip_mating_y, through its photo's camera since 2026-10-05) it makes the drop 4.06 in against Magpul's 4.0, and the right photo's makes it 3.94: one 0.06 over, the other 0.06 under. Neither is used for the scale (bottom_below_lower_underside adopts Magpul's figure): this entry keeps the disagreement in view."},"note":"Aero's two photos of the same product, each framed by five receiver features, agree on the trigger guard's bottom, the magazine well's lip and the tower's top within 0.02 in, and on where the grip sits and how it leans, but not on how far down its toe is: 0.11 in apart. Why isn't known (two lowers, or two views of the cap's edge)."},"bottom_below_lower_underside":{"label":"Grip bottom below the receiver's underside where the grip bears","kind":"length","measurements":[{"id":"magpul","value":4,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{.receiver_to_bottom}","via":"harvest"},"note":"Magpul's \"Height, receiver to bottom\", taken as from the underside the grip bears on to its lowest point. For the MOE-K2+ the same line on Magpul's page doesn't fit that reading (4.1 against a measured 4.65), so this one is taken because it checks, not because the page defines it."},{"id":"installed","value":4.058,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.toe_below_pin_line} + {bad-workhorse-lower.grip_mating_y}","via":"harvest"},"note":"The plain MOE's toe in Aero's left photo, less the mating surface's 1.072 in below the pins (the Workhorse's underside through its photo's camera, 2026-10-05: 4.034 while a two-pin frame read it 1.096). The right photo's toe makes it 3.94."}],"adopt":{"from":"magpul","reason":"The maker's figure for this grip. At this scale the design patent's front view comes to Magpul's 1.2 in thickness and the outline fits the plain MOE in both of Aero's photos; the left photo's toe agrees with it, the right photo's is 0.08 in short."},"note":"What the side photo is scaled by: the grip frame's origin (the rear end of its flat top, which bears on the receiver's underside) down to its toe."},"thickness":{"label":"Thickness (side to side)","kind":"length","measurements":[{"id":"magpul","value":1.2,"unit":"in","stated":"Thickness, max 1.2 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE+ Grip - AR15/M4 (MAG416)","url":"https://magpul.com/moe-plus-grip-ar15-m4.html","retrieved":"2026-10-01","via":"harvest"}},{"id":"patent","value":1.203,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-moe-plus bd5d1a90cef0 (US D600,310 S (Magpul MOE+), FIG. 4 front elevation, 300 dpi)","scaleRef":"scale from magpul-moe-plus.overall_height = 4.664 in (y-extent 958 px → 205.4 px/in)","method":"width of the traced outline (tools/trace.py); the patent's front elevation scaled to the traced side's height (orthographic views share it): its widest row","via":"harvest"}}],"adopt":{"from":"magpul","reason":"Manufacturer. The design patent's front view, scaled to the side photo's height, comes to the same: two sources that share nothing but the grip."}},"seat_x":{"label":"Seat, X: where the grip's frame origin (on its flat top's line, 0.17 in behind the flat's rear end as traced) sits ahead of the takedown pin, installed","kind":"length","measurements":[{"id":"aero-right","value":-0.255,"unit":"in","pm":0.055,"source":{"type":"photo","photo":"references/magpul-moe-plus d86458936f6f (Aero Precision APAR501124: a complete lower with the plain MOE, straight right side, 1000 x 1000)","scaleRef":"frame from the reviewed holes takedown, pivot, selector, hammer, trigger (63.7 px/in, rms 0.012 in over 5 points)","method":"x of the fitted profile's origin of the traced outline (tools/trace.py); the traced outline's origin (its flat top's rear end), fitted by rotation and translation (at the outline's own scale) to the grip's edges against the background","via":"harvest"}},{"id":"aero-left","value":-0.25,"unit":"in","pm":0.055,"source":{"type":"photo","photo":"references/magpul-moe-plus ffa403d63b08 (Aero Precision APAR501124: a complete lower with the plain MOE, straight left side, 1000 x 630)","scaleRef":"frame from the reviewed holes takedown, pivot, selector, hammer, trigger (63.3 px/in, rms 0.019 in over 5 points)","method":"x of the fitted profile's origin of the traced outline (tools/trace.py); the traced outline's origin (its flat top's rear end), fitted by rotation and translation (at the outline's own scale) to the grip's edges against the background","via":"harvest"}}],"adopt":{"from":"aero-right","reason":"Two pin-framed photos of the plain MOE (the MOE+'s shape) on Aero's lower, right and left, agree within 0.005 in; the right one's frame fits its five features closer (0.012 against 0.019 in rms)."},"note":"A grip's own figure on the standard AR-15 grip mount (D19, D28). Measured on the plain MOE (MAG415): no pin-framed photo of the MOE+ itself was found, and Magpul prints the same angle, height and thickness for both."},"lug_slot_width":{"label":"The slot in the top that goes over the receiver's lug, across","kind":"length","measurements":[{"id":"sibling","value":0.425,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{magpul-moe-k2-plus.lug_slot_width}","via":"user"},"note":"Not measured on an MOE+: no view of its top with a scale is on file. Taken to be the MOE-K2+'s, the same maker's grip for the same lug, read on the user's own (0.425 ± 0.02 against the lug's .375). Stands until a top view of an MOE+ is read."}]},"front_strap_face_width":{"label":"The front strap's face: how far across the grip its finger ribs run","kind":"length","measurements":[{"id":"patent","value":0.72,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-moe-plus bd5d1a90cef0 (US D600,310 S (Magpul MOE+), FIG. 4 front elevation, 300 dpi)","scaleRef":"the front elevation's own scale, 205.4 px/in (magpul-moe-plus.overall_height over its 958 px, at which its width is Magpul's 1.2 in)","method":"the two columns of ribs together, across the grip: sheet rows 2706 to 2854 (148 px) over columns 760 to 1060; the outline's two strokes are at rows 2658 and 2902","via":"harvest"}}],"note":"Where the ribs stop the strap rounds into the side. The round is taken as a circular arc, as on the MOE-K2+: no view on file looks along the strap."},"back_strap_face_width":{"label":"The back strap's face: how wide it is before it rounds into the sides","kind":"length","measurements":[{"id":"plan","value":0.2,"unit":"in","pm":0.1,"source":{"type":"photo","photo":"references/magpul-moe-plus bd5d1a90cef0 (US D600,310 S (Magpul MOE+), FIG. 6 top plan, 300 dpi)","scaleRef":"the plan's own width, 251 px for Magpul's 1.2 in; along the grip the elevations' 205.4 px/in (the plan is 667 px long: 3.25 in, the traced side's 3.24)","method":"the outline's width 20, 40, 60 and 100 px from its rear end (sheet rows 929 to 1009): 155, 193, 212 and 229 px, which is 0.74, 0.92, 1.01 and 1.10 in at 0.09, 0.17, 0.26 and 0.44 in from the back strap square to its axis (the plan looks down a strap leaning grip_angle). A round of 0.5 in radius either side of a flat 0.2 in wide has 0.76, 0.96, 1.08 and 1.19 there: within 0.02 in a side over the first 0.2 in and up to 0.05 fuller further round, where the grip goes on widening for an inch. FIG. 7, the bottom plan, has the same outline. ± for that, and for the base's bevel, which is part of the outline's first tenth of an inch","via":"harvest"}},{"id":"ridges","value":0.876,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-moe-plus bd5d1a90cef0 (US D600,310 S (Magpul MOE+), FIG. 5 rear elevation, 300 dpi)","scaleRef":"the front elevation's scale on the same sheet, 205.4 px/in: the two elevations are the same 962 px long and 244 px between their outlines' strokes","method":"the ridges' length across the grip: sheet rows 1865 to 2045 (180 px) over columns 1560 to 1860; the outline's two strokes are at rows 1833 and 2077","via":"harvest"},"note":"How far round the ridges run, seen from behind: an upper bound on the flat."}],"adopt":{"from":"plan","reason":"The plan shows the section; the rear elevation shows ridges that wrap a rounded strap, so their length across isn't a flat face's width. A strap flat for 0.88 in would have the plan's rear end at its full width 0.16 in from the end, where the figure has three quarters of it."},"note":"Two readings of two things. The sheet's top plan has the outline's rear end, which is the back strap's own section at the heel seen down the grip: nearly a full round. Its rear elevation has how far across the grip the ridges run, and they run on round the strap."},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"magpul","value":3.4,"unit":"oz","stated":"Weight 3.4 oz.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE+ Grip - AR15/M4 (MAG416)","url":"https://magpul.com/moe-plus-grip-ar15-m4.html","retrieved":"2026-10-01","via":"harvest"}}]},"overall_height":{"label":"Overall height in the grip frame (the beavertail's top to the toe)","kind":"length","measurements":[{"id":"photo","value":4.664,"unit":"in","pm":0.059,"source":{"type":"photo","photo":"references/magpul-moe-plus b9c00c3d5081 (Primary Arms MAG416-BLK_00.jpg: the MOE+ alone on white, straight right side, 2000 x 1334)","scaleRef":"scale from magpul-moe-plus.bottom_below_lower_underside = 4 in (y from the origin to the far edge 1047 px → 261.7 px/in)","method":"height of the traced outline (tools/trace.py); the traced outline's height, the beavertail's top to the toe (what the end section is scaled to)","via":"harvest"}}],"note":"What the end section from Magpul's design patent is scaled to (orthographic views share their height)."},"toe_y":{"label":"Toe (the grip's lowest point), Y in the grip frame","kind":"length","measurements":[{"id":"derived","value":-4,"unit":"in","source":{"type":"derived","expr":"-{.bottom_below_lower_underside}","via":"harvest"},"note":"Where the traced end section's toe sits, so it lines up with the side profile's."}]}}},{"subject":"magpul-moe-sl-carbine","title":"Magpul MOE SL carbine stock, mil-spec (MAG347)","dimensions":{"length":{"label":"Overall length","kind":"length","measurements":[{"id":"spec","value":7.3,"unit":"in","source":{"type":"spec","publisher":"manufacturer","name":"Magpul","url":"https://magpul.com/moe-sl-carbine-stock-mil-spec.html","retrieved":"2026-09-30","via":"brief"},"note":"Magpul: specifications assume a standard-length (flat-back) M4 carbine receiver extension."},{"id":"older-revision","value":7.2,"unit":"in","stated":"Length: 7.2\"","source":{"type":"spec","publisher":"retailer","name":"Primary Arms (older Magpul spec revision)","url":"https://www.primaryarms.com/magpul-moe-slim-line-carbine-stock-mil-spec-black-mag347-blk","retrieved":"2026-09-30","via":"harvest"},"note":"Magpul's earlier published figure, repeated by several retailers. Consistent with 7.3 within rounding if the true length is ~7.25 in."}],"adopt":{"from":"spec","reason":"Current manufacturer page."}},"lop_collapsed":{"label":"Length of pull, collapsed","kind":"length","measurements":[{"id":"spec","value":10.9,"unit":"in","stated":"LOP: ~10.9 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul","url":"https://magpul.com/moe-sl-carbine-stock-mil-spec.html","retrieved":"2026-09-30","via":"brief"},"note":"Magpul's figure assumes their own reference rifle and trigger."},{"id":"older-revision","value":10.8,"unit":"in","stated":"Length of Pull (Collapsed): ~10.8\"","source":{"type":"spec","publisher":"retailer","name":"Primary Arms (older Magpul spec revision)","url":"https://www.primaryarms.com/magpul-moe-slim-line-carbine-stock-mil-spec-black-mag347-blk","retrieved":"2026-09-30","via":"harvest"}},{"id":"operation-parts","value":11.1,"unit":"in","stated":"LOP: ~11.1 in.","source":{"type":"spec","publisher":"retailer","name":"Operation Parts","url":"https://operationparts.com/product/magpul-moe-sl-carbine-stock-mil-spec/","retrieved":"2026-09-30","via":"harvest"}}],"adopt":{"from":"spec","reason":"Current manufacturer page. Retailers carry at least two other revisions of this figure."}},"lop_extended":{"label":"Length of pull, extended","kind":"length","measurements":[{"id":"spec","value":14.2,"unit":"in","stated":"LOP: ~14.2 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul","url":"https://magpul.com/moe-sl-carbine-stock-mil-spec.html","retrieved":"2026-09-30","via":"brief"}},{"id":"older-revision","value":14.1,"unit":"in","stated":"Length of Pull (Extended): ~14.1\"","source":{"type":"spec","publisher":"retailer","name":"Primary Arms (older Magpul spec revision)","url":"https://www.primaryarms.com/magpul-moe-slim-line-carbine-stock-mil-spec-black-mag347-blk","retrieved":"2026-09-30","via":"harvest"}},{"id":"operation-parts","value":14.4,"unit":"in","stated":"LOP: ~14.4 in.","source":{"type":"spec","publisher":"retailer","name":"Operation Parts","url":"https://operationparts.com/product/magpul-moe-sl-carbine-stock-mil-spec/","retrieved":"2026-09-30","via":"harvest"}}],"adopt":{"from":"spec","reason":"Current manufacturer page."}},"positions":{"label":"Number of positions","kind":"count","measurements":[{"id":"spec","value":6,"unit":"count","source":{"type":"spec","publisher":"manufacturer","name":"Magpul","url":"https://magpul.com/moe-sl-carbine-stock-mil-spec.html","retrieved":"2026-09-30","via":"brief"}}]},"travel":{"label":"Travel, position 1 to 6","kind":"length","measurements":[{"id":"spec","value":3.3,"unit":"in","source":{"type":"spec","publisher":"manufacturer","name":"Magpul","url":"https://magpul.com/moe-sl-carbine-stock-mil-spec.html","retrieved":"2026-09-30","via":"brief"}},{"id":"from-lop","value":3.3,"unit":"in","source":{"type":"derived","expr":"{.lop_extended} - {.lop_collapsed}","via":"brief"}}],"adopt":{"from":"spec","reason":"Stated directly; the LOP range agrees."}},"position_step":{"label":"Travel per position","kind":"length","measurements":[{"id":"derived","value":0.66,"unit":"in","stated":"0.66 in per step","source":{"type":"derived","expr":"{.travel} / ({.positions} - 1)","via":"brief"}}]},"tube_axis_below_top":{"label":"Tube axis below the stock's top edge","kind":"length","measurements":[{"id":"photo","value":0.667,"unit":"in","source":{"type":"photo","photo":"Magpul MOE SL side product photo (not yet archived)","scaleRef":"not recorded in brief","method":"calibrated photo measurement","via":"brief"}},{"id":"patent","value":0.718,"unit":"in","pm":0.055,"source":{"type":"photo","photo":"references/magpul-moe-sl-carbine 505db255225b (US D736,336 S, Magpul's design patent, FIG. 7 front elevation, 300 dpi)","scaleRef":"the figure's height and width = Magpul's 5.3 and 1.7 in (307.7 px/in each, agreeing within 0.0%)","method":"least-squares circle through the hidden-line bore (1.163 in across, rms 2.8 px), its centre below the outline's top; a second dashed circle (1.136 across) centres 0.054 lower, so the ± spans both","via":"harvest"}}],"adopt":{"from":"photo","reason":"The brief's figure, which the side profile and the stock's seat were built on; Magpul's patent agrees within its ± (its bore centre reads 0.05–0.10 lower: a calibrated installed photo could settle it)."}},"butt_behind_pin_pos2":{"label":"Butt behind takedown pin, position 2 (mil-spec carbine tube)","kind":"length","measurements":[{"id":"photo","value":9.73,"unit":"in","source":{"type":"photo","photo":"Magpul MOE SL side product photo (not yet archived)","scaleRef":"not recorded in brief","method":"calibrated photo measurement","via":"brief"}}]},"butt_behind_pin_pos1":{"label":"Butt behind takedown pin, position 1 (mil-spec carbine tube)","kind":"length","measurements":[{"id":"derived","value":9.07,"unit":"in","pm":0.1,"stated":"about 9.07 in, ±0.1 in","source":{"type":"derived","expr":"{.butt_behind_pin_pos2} - {.position_step}","via":"brief"}},{"id":"aero-photo","value":9.13,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/bcm-stock-kit b6118d35ed00 (Aero Precision M4E1 complete lower with MOE SL, straight right side, 2000 px; supplied in chat)","scaleRef":"pin frame: takedown, pivot, trigger, hammer, selector (Hough-refined), 130.6 px/in, rms 0.022 in","method":"stock front edge at 1.83 in behind the takedown pin (fully collapsed), + Magpul's 7.3 in length. The butt itself is at the frame's edge, where lens compression reads the stock ~6% small, so the front edge near the pins is used","via":"user"},"note":"Read at a scale 2.5% too large (2026-10-05): the same five features fit the Army drawing's positions at 127.4 px/in with an rms of 0.003 in, and at that scale the front edge (column 910) is 1.92 in behind the pin before anything is allowed for the tube's silhouette standing further from the lens than the pins' heads. The reading called installed is the same photo read locally."},{"id":"installed","value":9.255,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"-{std.ar15.receiver_rear_x} + {.front_behind_receiver_pos1} + {.length}","via":"user"},"note":"The user's photo of one collapsed on a lower: the stock's front behind the receiver's rear face, read between edges an inch apart, on the Army drawing's rear face, plus Magpul's length. ± is the photo's 0.03 and the length's last digit."},{"id":"holes","value":9.243,"unit":"in","pm":0.07,"source":{"type":"derived","expr":"{bcm-receiver-extension.tube_front_behind_pin} + {bcm-receiver-extension.tube_length} - {bcm-receiver-extension.position_hole_rear_from_rear} - 5 * {bcm-receiver-extension.position_step} - {.lock_pin_behind_front} + {.length}","via":"user"},"note":"The lock pin in the tube's front hole. ± for the hole's place (0.03), the tube's seat (0.02) and the pin's (0.04), and for the tube's length, which is a generic figure."}],"adopt":{"from":"installed","reason":"Seated from a photo of it installed, collapsed, square from the side, read from the receiver's rear face (2026-10-05); its lock pin in the receiver extension's front hole says the same within 0.02 in, and Magpul's current lengths of pull put it 0.6 in behind the MOE Carbine, where this has it 0.56. The brief's 9.07 (a photo that isn't on file, less one step) is 0.19 in less and outside the two ±: it had the stock's front 0.05 in behind the castle nut, where the photo has 0.3 in of receiver extension showing. The first reading of the user's photo (9.13) was made at a scale 2.5% too large. Weighed against it: the brief's overall length for this build collapsed (asm.v1.oal_pos1, 30.5 in), which the build now reads 0.40 in over (30.90; 30.715 with the 9.07). It is no second witness: the brief gives it as the sum of this same butt position and a muzzle it didn't record, 0.215 in short of the muzzle since measured on the user's own upper, and no photo of the whole rifle is on file behind it."}},"front_behind_receiver_pos1":{"label":"Stock's front face behind the receiver's rear face, position 1 (collapsed)","kind":"length","measurements":[{"id":"aero-photo","value":0.83,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/bcm-stock-kit b6118d35ed00 (Aero Precision M4E1 complete lower with MOE SL, collapsed, straight right side, 2000 px; supplied in chat)","scaleRef":"the mid-plane's scale beside the edges read, 125 ± 2 px/in: under the pin frame's 127.4 (takedown, pivot, hammer, trigger and selector on the Army drawing's positions, rms 0.003 in: the pins' near ends, nearer the lens than the tube's silhouette) and over the 122 that the extension's 1.148 in gives across 140 px (a black tube reads thin on white); the castle nut's 173 px is 1.36 to 1.375 in, as three other makers' nuts are, at 125.8 to 127.2","method":"columns on the silhouette at the tube's top and bottom (luminance < 235) and on a 6x crop: the stock's front face 910, the receiver's rear face, where the end plate's lobe ends against it, 1013.5: 103.5 px. Both edges are in the tube's mid-plane and within 0.9 in of the frame's middle. ± is the scale's 0.013 and two edges at 1.5 px","via":"user"}}],"note":"Read locally, between edges an inch apart on the receiver extension's own silhouette, so the photo's frame doesn't enter: the receiver's rear face is the Army drawing's (std.ar15.receiver_rear_x). The same photo has 0.31 in of receiver extension showing between the castle nut and the stock (39 px), Aero's nut 0.37 in long (46.5 px) and its end plate 0.14 (18 px). It is one photo, of another maker's receiver extension than the kit's."},"lock_pin_behind_front":{"label":"Lock pin behind the stock's front face","kind":"length","measurements":[{"id":"installed","value":2.236,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/bcm-stock-kit b6118d35ed00 (Aero Precision M4E1 complete lower with MOE SL, collapsed, straight right side, 2000 px; supplied in chat)","scaleRef":"the stock's own length in the same photo, 904.5 px (its silhouette's columns 6 to 910.5) for Magpul's 7.3 in: 123.9 px/in","method":"the pin's round head (columns 620 to 643) over its track (622 to 648), centred 633: 277 px behind the front face; ± is 3 px and the length's last digit","via":"user"}}],"note":"The steel pin the latch draws out of the receiver extension's holes: its round head shows over its track, ahead of the latch's pivot. Where it stands says which hole the stock is on. The patent's bottom plan has the latch's front end round it 4.97 to 5.23 in ahead of the butt (latch_front_half_width): 2.2 behind the front."},"height":{"label":"Height","kind":"length","measurements":[{"id":"spec","value":5.3,"unit":"in","stated":"Height: 5.3 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul","url":"https://magpul.com/moe-sl-carbine-stock-mil-spec.html","retrieved":"2026-09-30","via":"harvest"}},{"id":"photos","value":5.3,"unit":"in","pm":0.11,"stated":"5.15–5.36 in across four side views","source":{"type":"photo","photo":"references/magpul-moe-sl-carbine: 69e84f01b026, ea9d84b7c987, 7f4d132df6c1, c32021770736","scaleRef":"published overall length 7.3 in (single-scale)","method":"silhouette bounding-box height / width × 7.3; median of four, ± spans them","via":"harvest"},"note":"Corroborates the spec height; only checks proportions, since it's scaled from the spec length."},{"id":"wing","value":5.26,"unit":"in","stated":"Height: 5.26\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical","url":"https://www.wingtactical.com/firearm-parts/ar-15/stocks-accessories/magpul-moe-sl-slim-line-stock-mil-spec/","retrieved":"2026-09-30","via":"harvest"}}],"adopt":{"from":"spec","reason":"Manufacturer."}},"width":{"label":"Width","kind":"length","measurements":[{"id":"spec","value":1.7,"unit":"in","stated":"Width: 1.7 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul","url":"https://magpul.com/moe-sl-carbine-stock-mil-spec.html","retrieved":"2026-09-30","via":"harvest"}},{"id":"wing","value":1.67,"unit":"in","stated":"Width: 1.67\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical","url":"https://www.wingtactical.com/firearm-parts/ar-15/stocks-accessories/magpul-moe-sl-slim-line-stock-mil-spec/","retrieved":"2026-09-30","via":"harvest"}}],"adopt":{"from":"spec","reason":"Manufacturer."}},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"spec","value":9.3,"unit":"oz","stated":"Weight: 9.3 oz.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul","url":"https://magpul.com/moe-sl-carbine-stock-mil-spec.html","retrieved":"2026-09-30","via":"harvest"},"note":"The page lists a second, unlabeled weight (~13.1 oz); its meaning isn't clear, so it isn't recorded."},{"id":"older-revision","value":9.6,"unit":"oz","stated":"Weight: 9.6 oz","source":{"type":"spec","publisher":"retailer","name":"Primary Arms (older Magpul spec revision)","url":"https://www.primaryarms.com/magpul-moe-slim-line-carbine-stock-mil-spec-black-mag347-blk","retrieved":"2026-09-30","via":"harvest"}}],"adopt":{"from":"spec","reason":"Current manufacturer page."}},"latch_tab_half_width":{"label":"The latch's grip: how far out from the middle its face stands","kind":"length","measurements":[{"id":"patent","value":0.661,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-moe-sl-carbine 505db255225b (US D736,336 S (Magpul), FIG. 7 front elevation, 300 dpi)","scaleRef":"the front profile's scale: its height = Magpul's 5.3 in (1631 px, 307.7 px/in), its width 1.7 in across 523 px (agree)","method":"each tab's outer edge from the silhouette's middle at its height: 203.5 px left and right (crop columns 75 and 482 about 278.5)","via":"harvest"}},{"id":"plan","value":0.655,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-moe-sl-carbine cb5fcd378303 (US D736,336 S (Magpul), FIG. 9 bottom plan, 300 dpi; the patent office's copy)","scaleRef":"the figure's width = Magpul's 1.7 in (521 px: 306.5 px/in); its length then reads 7.24 against the published 7.3; x from the pad's rearmost row, the side outline's origin","method":"the grip's outer line, rows 1400-1660 (x 2.53-3.37), both sides: 0.653-0.656 from the middle (stroke centres; .cache/research/magpul/fig9b.py)","via":"harvest"}}],"adopt":{"from":"plan","reason":"FIG. 9 shows each piece of the latch where it is along the stock; FIG. 7's 0.661 agrees."},"note":"The latch lies in the side pockets, a grip tab each side (FIG. 7 draws the two hatched), proud of the pocket floor and inside the stock's outline."},"latch_boss_half_width":{"label":"The latch's pivot boss: how far out from the middle its face stands","kind":"length","measurements":[{"id":"patent","value":0.595,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-moe-sl-carbine 505db255225b (US D736,336 S (Magpul), FIG. 7 front elevation, 300 dpi)","scaleRef":"the front profile's scale: its height = Magpul's 5.3 in (1631 px, 307.7 px/in), its width 1.7 in across 523 px (agree)","method":"the square boss above each tab (the pivot's head), its outer edge from the middle: 184.5 px left, 181.5 right","via":"harvest"}},{"id":"plan","value":0.512,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-moe-sl-carbine cb5fcd378303 (US D736,336 S (Magpul), FIG. 9 bottom plan, 300 dpi; the patent office's copy)","scaleRef":"the figure's width = Magpul's 1.7 in (521 px: 306.5 px/in); its length then reads 7.24 against the published 7.3; x from the pad's rearmost row, the side outline's origin","method":"the outline bulges over x 4.20-4.60, where the photo's round pivot boss is (4.15-4.59): 0.509-0.515, both sides","via":"harvest"}}],"adopt":{"from":"plan","reason":"FIG. 9 shows each piece of the latch where it is along the stock (2026-10-03). FIG. 7's 0.595 is the outermost line at that height seen from the front: the latch's front end at the lock pin, x 4.97-5.23 (latch_front_half_width), which FIG. 9 has at 0.59. The boss had been drawn 0.08 in too wide each side."}},"latch_grip_front_x":{"label":"The latch's grip, where it ends and the arm begins, X from the butt","kind":"length","measurements":[{"id":"plan","value":3.46,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-moe-sl-carbine cb5fcd378303 (US D736,336 S (Magpul), FIG. 9 bottom plan, 300 dpi; the patent office's copy)","scaleRef":"the figure's width = Magpul's 1.7 in (521 px: 306.5 px/in); its length then reads 7.24 against the published 7.3; x from the pad's rearmost row, the side outline's origin","method":"the grip's front end, chamfered in to the arm over x 3.37-3.50 (305.3 px/in along it)","via":"harvest"}}]},"latch_arm_half_width":{"label":"The latch's arm: how far out from the middle its face stands","kind":"length","measurements":[{"id":"plan","value":0.477,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-moe-sl-carbine cb5fcd378303 (US D736,336 S (Magpul), FIG. 9 bottom plan, 300 dpi; the patent office's copy)","scaleRef":"the figure's width = Magpul's 1.7 in (521 px: 306.5 px/in); its length then reads 7.24 against the published 7.3; x from the pad's rearmost row, the side outline's origin","method":"the arm's outer line, x 3.46-4.20 and 4.60-4.97: 0.471-0.485, both sides","via":"harvest"}}]},"latch_front_half_width":{"label":"The latch's front end, round the lock pin: how far out from the middle its face stands","kind":"length","measurements":[{"id":"plan","value":0.59,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-moe-sl-carbine cb5fcd378303 (US D736,336 S (Magpul), FIG. 9 bottom plan, 300 dpi; the patent office's copy)","scaleRef":"the figure's width = Magpul's 1.7 in (521 px: 306.5 px/in); its length then reads 7.24 against the published 7.3; x from the pad's rearmost row, the side outline's origin","method":"a block each side at x 4.97-5.23, from 0.40 out to 0.566-0.595 (rows 2160-2220)","via":"harvest"}},{"id":"front","value":0.595,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-moe-sl-carbine 505db255225b (US D736,336 S (Magpul), FIG. 7 front elevation, 300 dpi)","scaleRef":"the front profile's scale (307.7 px/in)","method":"the square block above each tab: 184.5 px left, 181.5 right (the reading latch_boss_half_width had)","via":"harvest"}}],"adopt":{"from":"plan","reason":"FIG. 9 places it along the stock; FIG. 7's agrees."},"note":"Drawn since 2026-10-13 as the lock pin's own head (lock_pin_face_half_width): FIG. 7 draws the same blocks from the front as squares 0.19 in high, which is the head's size on the side photo. The latch's hook round the pin still isn't drawn: its outline can't be told from the slot's shadow on the side photo on file."},"bore_diameter":{"label":"The bore for the receiver extension, as the patent draws it","kind":"length","measurements":[{"id":"patent","value":1.163,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-moe-sl-carbine 505db255225b (US D736,336 S, Magpul's design patent, FIG. 7 front elevation, 300 dpi)","scaleRef":"the figure's height and width = Magpul's 5.3 and 1.7 in (307.7 px/in each, agreeing within 0.0%)","method":"the diameter of the least-squares circle through the hidden-line bore (rms 2.8 px, 0.009 in); ± also spans the second dashed circle the figure draws, 1.136 across","via":"harvest"}}],"note":"No published bore is on file for this stock, only that MAG347 is the Mil-Spec model (std.receiver_extension.milspec_od is 1.148). This is the larger of the two dashed circles tube_axis_below_top's patent reading fits; the smaller is less than the tube across and can't be what the tube passes through."},"rail_channel_width":{"label":"Width of the channel under the bore, for the receiver extension's indexing rail","kind":"length","measurements":[{"id":"rail","value":0.49,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.receiver_extension.rail_width}","via":"harvest"}}],"note":"Not read from this stock: the mil-spec tube's rail at its own width, with nothing to spare (no clearance is known). The patent's front elevation hasn't been read for the mouth's neck."},"rail_channel_floor_below_axis":{"label":"Floor of the indexing rail's channel, below the tube axis","kind":"length","measurements":[{"id":"rail","value":0.874,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.receiver_extension.rail_bottom_below_axis}","via":"harvest"}}],"note":"Not read from this stock: where the mil-spec tube's rail ends below its axis, with nothing to spare (no clearance is known)."},"panel_recess_depth":{"label":"The floors inside the frame: how far they lie in from the frame's face","kind":"length","measurements":[{"id":"shadow","value":0.05,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-moe-sl-carbine 9b34a5d996e8 (MOE SL, straight right side view on white, 2485 px; supplied by the user from their downloads, source not recorded)","scaleRef":"the side profile's own scale, 328.1 px/in: Magpul's 7.3 in length across 2413 px and 5.3 in height across 1726 px, which agree within 1.5%","method":"the shadow the frame's member casts on the triangle's floor under the QD socket (the dark line along the member's lower edge), 12 px high (0.037 in), over the light's slope: the cheek's own shadow is 94 px (0.29 in; rows 421 to 515 along column 600) under an overhang of 0.39 in (the outline's 0.85 less the web's 0.46), 0.74 in of shadow to an inch of step. ± is 4 px of shadow and the slope's","via":"user"}},{"id":"patent","value":0.05,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/magpul-moe-sl-carbine 505db255225b (US D736,336 S (Magpul), FIG. 7 front elevation, 300 dpi)","scaleRef":"the front profile's scale: its height = Magpul's 5.3 in (1631 px, 307.7 px/in), its width 1.7 in across 523 px (agree); the middle is column 1665","method":"two strokes each side down the wall under the cheek, rows 1390 to 1545 (strokes' middles along eight rows; .cache/detail/magpul-moe-sl-carbine/patent.py): the outer at 0.43 to 0.46 from the middle, which is the line the web's outline was picked on (0.46 on row 1525, where that outline begins), and an inner one at 0.385 to 0.411: 0.03 to 0.075 apart","via":"harvest"}}],"adopt":{"from":"shadow","reason":"Read on the photo the floors are outlined on; the patent's front view, read on its own, says the same."},"note":"No view on file is square across a floor. Two readings that don't share a source say about a twentieth of an inch, and it is drawn as one depth for the pocket's floors, the triangle's and the groove round the QD socket. Under the cheek the pocket has a step along it 0.37 in below the cheek's edge (rows 557 to 560 of the side photo) with a shadow 0.14 in high under it: not drawn, since which side of it stands proud isn't read."},"grip_teeth":{"label":"The latch's grip: its ridges","kind":"count","measurements":[{"id":"side","value":12,"unit":"count","source":{"type":"photo","photo":"references/magpul-moe-sl-carbine 9b34a5d996e8 (MOE SL, straight right side view on white, 2485 px; supplied by the user from their downloads, source not recorded)","scaleRef":"a count","method":"the ridges' ends in profile along the upper edge of the grip's dark face, against the lit band over it: ten found as dark steps along a line 11 px under the grip's upper edge (27 px apart, from 6.5 to 249.5 px along it from 840,679), and two more seen on a 4x crop at columns 1113 and 1140, where the ridged edge has drawn away from that line; none in the 27 px left before the grip's front end","via":"user"}},{"id":"left","value":12,"unit":"count","source":{"type":"photo","photo":"references/magpul-moe-sl-carbine cdd8efea5595 (Magpul's gallery, FDE 03, straight left side, 1200 px)","scaleRef":"a count","method":"the dark lines across the grip's face along a line through its lower third: twelve, 9.83 px apart, columns 608.9 to 717.0 (brightness along the line; .cache/detail/magpul-moe-sl-carbine/measure.py)","via":"harvest"}}],"adopt":{"from":"side","reason":"Both photos count twelve, each over the whole row."}},"grip_tooth_pitch":{"label":"The latch's grip: from one ridge to the next, along the grip","kind":"length","measurements":[{"id":"side","value":0.082,"unit":"in","pm":0.002,"source":{"type":"photo","photo":"references/magpul-moe-sl-carbine 9b34a5d996e8 (MOE SL, straight right side view on white, 2485 px; supplied by the user from their downloads, source not recorded)","scaleRef":"the side profile's own scale, 328.1 px/in: Magpul's 7.3 in length across 2413 px and 5.3 in height across 1726 px, which agree within 1.5%","method":"27.0 px from ridge to ridge over nine intervals (243 px along the grip's upper edge); Magpul's left side photo has 9.9 px along the grip, the same at its own 120 px/in. ± is the scale's 1.5% and a pixel over the run","via":"user"}}]},"grip_first_tooth":{"label":"The latch's grip: its rearmost ridge, along the grip from its rear upper corner","kind":"length","measurements":[{"id":"side","value":0.045,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-moe-sl-carbine 9b34a5d996e8 (MOE SL, straight right side view on white, 2485 px; supplied by the user from their downloads, source not recorded)","scaleRef":"the side profile's own scale, 328.1 px/in: Magpul's 7.3 in length across 2413 px and 5.3 in height across 1726 px, which agree within 1.5%","method":"the first ridge's tip 14.6 px along the upper edge from the corner the outline has at 832,680 (6.5 px along the line begun at 840,679); ± is 2.5 px","via":"user"}}]},"grip_tooth_height":{"label":"The latch's grip: how far a ridge stands from the hollow beside it","kind":"length","measurements":[{"id":"side","value":0.023,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-moe-sl-carbine 9b34a5d996e8 (MOE SL, straight right side view on white, 2485 px; supplied by the user from their downloads, source not recorded)","scaleRef":"the side profile's own scale, 328.1 px/in: Magpul's 7.3 in length across 2413 px and 5.3 in height across 1726 px, which agree within 1.5%","method":"the scallops the ridges' ends make against the lit band, 6 to 9 px from a tip to the hollow beside it on a 4x crop; a ridge's end is rounded there, so along its length it may stand further","via":"user"}}]},"grip_edge_height":{"label":"The latch's grip: its outer edge, from its upper face down to where the ridged face begins","kind":"length","measurements":[{"id":"side","value":0.037,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-moe-sl-carbine 9b34a5d996e8 (MOE SL, straight right side view on white, 2485 px; supplied by the user from their downloads, source not recorded)","scaleRef":"the side profile's own scale, 328.1 px/in: Magpul's 7.3 in length across 2413 px and 5.3 in height across 1726 px, which agree within 1.5%","method":"the lit band between the grip's upper edge and the ridges' tips, 10 to 14 px along it","via":"user"}},{"id":"patent","value":0.1,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-moe-sl-carbine 505db255225b (US D736,336 S (Magpul), FIG. 7 front elevation, 300 dpi)","scaleRef":"the front profile's scale: its height = Magpul's 5.3 in (1631 px, 307.7 px/in), its width 1.7 in across 523 px (agree); the middle is column 1665","method":"the grip's outer end each side, an upright stroke 0.635 to 0.64 from the middle from its upper face (rows 1445 to 1450) down to rows 1472 to 1480, where the hatched face turns in (0.56 on row 1490, 0.46 on row 1525): 27 to 34 px","via":"harvest"}}],"adopt":{"from":"side","reason":"The photo of the part as made, on which the grip is outlined; Magpul's own left side photo has the ridges to within 0.1 in of the upper edge as well. The patent's figure is a design drawing of 2014 and disagrees with the photo by more than both ±."},"note":"On the side photo the ridges come up to a lit band 12 px high under the grip's upper edge. That band may be the grip's upper face seen from a little above (9 degrees would show it so) and not an upright edge at all; the patent draws an upright end nearly three times as high. Drawn as the photo's."},"grip_foot_half_width":{"label":"The latch's grip: how far out from the middle its ridged face ends, at its lower edge","kind":"length","measurements":[{"id":"patent","value":0.415,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-moe-sl-carbine 505db255225b (US D736,336 S (Magpul), FIG. 7 front elevation, 300 dpi)","scaleRef":"the front profile's scale: its height = Magpul's 5.3 in (1631 px, 307.7 px/in), its width 1.7 in across 523 px (agree); the middle is column 1665","method":"the hatched face's lower edge runs down and in to the wall each side: 0.46 from the middle on row 1525, 0.426 on row 1537 and 0.411 on row 1545 (both sides alike), toward the wall's inner stroke at 0.385. The figure is the middle of what it passes over those last rows; ± spans them","via":"harvest"}}]},"lock_slot_floor_half_width":{"label":"The lock pin's slot: how far out from the middle its floor is","kind":"length","measurements":[{"id":"plan","value":0.403,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/magpul-moe-sl-carbine cb5fcd378303 (US D736,336 S (Magpul), FIG. 9 bottom plan, 300 dpi; the patent office's copy)","scaleRef":"the figure's width = Magpul's 1.7 in (521 px: 306.5 px/in); the middle is column 1659.5","method":"the lock pin's block each side begins there: strokes at columns 1535.5 and 1782.5 (0.405, 0.401) along rows 2170 to 2195, the block 57.5 px long (rows 2161.5 to 2219: 0.188 in, the head's size on the side photo) and out to 0.577 to 0.595 (the reading latch_front_half_width has as 0.40 to 0.59)","via":"harvest"}},{"id":"front","value":0.43,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/magpul-moe-sl-carbine 505db255225b (US D736,336 S (Magpul), FIG. 7 front elevation, 300 dpi)","scaleRef":"the front profile's scale: its height = Magpul's 5.3 in (1631 px, 307.7 px/in), its width 1.7 in across 523 px (agree); the middle is column 1665","method":"the square the pin's head makes each side begins at the strokes at columns 1533.5 and 1798.0 (0.427, 0.432) along row 1372, and is out to 0.590 and 0.591; rows 1344 to 1402.5 (0.19 in)","via":"harvest"}}],"adopt":{"from":"plan","reason":"FIG. 9 looks straight along the slot from below; in FIG. 7 the head's inner end is where it meets the wall's silhouette, which is the slot's mouth and not its floor. The two differ by more than both ±, and the difference is about the slot's depth."}},"lock_pin_face_half_width":{"label":"The lock pin's head: how far out from the middle its face stands","kind":"length","measurements":[{"id":"plan","value":0.59,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{.latch_front_half_width}","via":"harvest"}}],"note":"The blocks FIG. 9 draws each side at the lock pin, read here as the pin's own ends: FIG. 7 has them as squares 0.19 in high (rows 1344 to 1402.5) out to 0.590 and 0.591, FIG. 9 as blocks 0.188 in long, and the head on the side photo is 0.186 in across. The patent draws them 0.15 in lower than the photo has the head."}}},{"subject":"magpul-moe-sl-handguard-carbine","title":"Magpul MOE SL® Hand Guard, Carbine-Length – AR15/M4 (MAG538)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"magpul","value":6.7,"unit":"oz","stated":"Weight 6.7 oz.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE SL® Hand Guard, Carbine-Length – AR15/M4, Model MAG538: Technical Specifications","url":"https://magpul.com/moeslhandguard-carbine-length-ar15-m4.html","retrieved":"2026-10-28","via":"harvest"}},{"id":"primary-arms","value":6.7,"unit":"oz","stated":"Weight 6.7 oz..","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Magpul MOE SL Drop In AR-15 Handguard - M-LOK - Carbine Length - Grey (MAG538-GRY)","url":"https://www.primaryarms.com/magpul-moe-slim-line-handguard-carbine-length-stealth-grey-mag538-gry","retrieved":"2026-10-28","via":"harvest"}}],"adopt":{"from":"magpul","reason":"The maker's figure; Primary Arms' page states the same."},"note":"The two halves together, the lower one with its riveted aluminium heat shield. (KY Gun Co's page gives \"Weight 1 lb\": a shipping weight, left out.)"},"length":{"label":"Length, maximum","kind":"length","measurements":[{"id":"magpul","value":8.9,"unit":"in","stated":"Length, max 8.9 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE SL® Hand Guard, Carbine-Length – AR15/M4, Model MAG538: Technical Specifications","url":"https://magpul.com/moeslhandguard-carbine-length-ar15-m4.html","retrieved":"2026-10-28","via":"harvest"}},{"id":"primary-arms","value":8.9,"unit":"in","stated":"Handguard Length 8.9","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Magpul MOE SL Drop In AR-15 Handguard - M-LOK - Carbine Length - Grey (MAG538-GRY)","url":"https://www.primaryarms.com/magpul-moe-slim-line-handguard-carbine-length-stealth-grey-mag538-gry","retrieved":"2026-10-28","via":"harvest"}},{"id":"photo","value":9.06,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-carbine 94b9fe2cb318 (Magpul's mag538-fde_04: the Flat Dark Earth hand guard on a rifle, the rifle's right side seen level, 1200 x 1200)","scaleRef":"its three M-LOK slots, centres 686.5, 739.5 and 792.5 px: 53.0 px for the standard's 40 mm (std.mlok.slot_pitch), 33.65 px/in","method":"the outline at saturation > 0.15 from its rear (the tongues over the delta ring, column 607) to the side extensions' front tip (912): 305 px; ± 2 px at each end","via":"harvest"}}],"adopt":{"from":"magpul","reason":"The maker's figure; the photo, scaled by the standard's M-LOK pitch and by nothing of the part, reads 1.8% more, two pixels at each end of a 305 px outline."},"note":"From the rear end of the tongues that reach back over the delta ring to the tip of the side extensions, which wrap the front sight base (\"Front lip and long side extensions shields hand from hot sight assembly\")."},"mounting_length":{"label":"Length, mounting (from its rear flange's end on the delta ring's lip to its front flange's end in the cap)","kind":"length","measurements":[{"id":"magpul","value":6.6,"unit":"in","stated":"Length, mounting: 6.6 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE SL® Hand Guard, Carbine-Length – AR15/M4, Model MAG538: Technical Specifications","url":"https://magpul.com/moeslhandguard-carbine-length-ar15-m4.html","retrieved":"2026-10-28","via":"harvest"}}],"note":"Magpul says no more than the figure; read as on its MOE M-LOK carbine (MAG424, the same 6.6 in on its page): what the rifle's delta ring and round cap hold the hand guard between. The front sight base's rear in the FDE photo (its tower's front leg at column 905, less the base's 1.804 in, bcm-front-sight-base-f-750.length) stands 6.49 in ahead of the bearing face read there: the flange's end goes 0.1 past the cap's floor, which the ring's spring takes up."},"width":{"label":"Width","kind":"length","measurements":[{"id":"magpul","value":1.8,"unit":"in","pm":0.05,"stated":"Width 1.8 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE SL® Hand Guard, Carbine-Length – AR15/M4, Model MAG538: Technical Specifications","url":"https://magpul.com/moeslhandguard-carbine-length-ar15-m4.html","retrieved":"2026-10-28","via":"harvest"}},{"id":"magpul-features","value":1.8,"unit":"in","pm":0.05,"stated":"1/3\" NARROWER PROFILE THAN ORIGINAL MOE (1.8\" RATHER THAN 2.2\")","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE SL® Hand Guard, Carbine-Length – AR15/M4, Model MAG538: Technical Specifications","url":"https://magpul.com/moeslhandguard-carbine-length-ar15-m4.html","retrieved":"2026-10-28","via":"harvest"}},{"id":"photo","value":1.73,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-carbine 11a885bc3699 (Magpul's feature 03 for MAG538: the black hand guard alone from above, 700 x 525)","scaleRef":"its side M-LOK slots seen edge-on along each edge, 100.0 px apart for the standard's 40 mm: 63.5 px/in at the side faces","method":"the body's silhouette across, rows 215 to 324 at column 300: 110 px; its sides are further from a lens above than its top, so it reads narrow","via":"harvest"}}],"adopt":{"from":"magpul","reason":"The maker's figure, said twice on its page. The view from above, scaled at the side faces' depth, reads 4% less, as a lens close above it would."}},"height":{"label":"Height","kind":"length","measurements":[{"id":"magpul","value":2.4,"unit":"in","pm":0.05,"stated":"Height: 2.4 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE SL® Hand Guard, Carbine-Length – AR15/M4, Model MAG538: Technical Specifications","url":"https://magpul.com/moeslhandguard-carbine-length-ar15-m4.html","retrieved":"2026-10-28","via":"harvest"}},{"id":"photo","value":2.32,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-carbine 94b9fe2cb318 (Magpul's mag538-fde_04: the FDE hand guard on a rifle, its right side seen level)","scaleRef":"its M-LOK slots at the standard's pitch: 33.65 px/in","method":"the body's top (row 534) to its bottom (612) clear of the front lip, columns 640 to 830: 78 px; ± 1.5 px each edge","via":"harvest"}}],"adopt":{"from":"photo","reason":"The model is drawn from the traced outline, at the photo's height. Magpul's 2.4 is 3% more; what it measures over isn't said (the front lip reaches lower). The mid-length's own photo reads 2.32 too, at twice this one's resolution."}},"inside_diameter":{"label":"Inside diameter","kind":"length","measurements":[],"note":"Magpul gives none. The model's inside is its outside less the wall (wall), which no view gives either."},"rear_x":{"label":"Its rear flange's end (bearing on the delta ring's lip) ahead of the receiver's front face","kind":"length","measurements":[{"id":"derived","value":0.336,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{std.ar15.slip_ring_front_x}","via":"harvest"}}],"note":"Where the standard's delta ring holds it (std.ar15.slip_ring_front_x, from the Army's drawings): its rear flanges in the ring's skirt, against the lip. Its instruction sheet: \"When both halves are in place, make sure your delta ring is securing BOTH upper and lower rear flanges of the Hand Guards\"."},"window_length":{"label":"The window in each side of its rear end, where the delta ring shows: from the tongues' rear end to the window's front edge","kind":"length","measurements":[{"id":"photo","value":0.68,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-carbine 94b9fe2cb318 (Magpul's mag538-fde_04: the FDE hand guard on a rifle, its right side seen level)","scaleRef":"its M-LOK slots: 33.65 px/in","method":"the tongues' rear edge (column 607) to the window's front edge, where the black ring ends and the body's side begins (630): 23 px; ± 2 px","via":"harvest"}}],"note":"The ring fills the window in every photo of it on a rifle: its front edge is where the ring's front end is."},"tongue_reach":{"label":"How far the tongues reach back over the delta ring behind its rear flange's end","kind":"length","measurements":[{"id":"derived","value":0.56,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{.window_length} - {std.ar15.slip_ring_skirt_length}","via":"harvest"}}],"note":"The window's front edge is the ring's front end, which stands the ring's skirt ahead of the lip the flanges bear on (std.ar15.slip_ring_skirt_length)."},"outline_rear_x":{"label":"The tongues' rear end (where the side outline begins), from its rear flange's end","kind":"length","measurements":[{"id":"derived","value":-0.56,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"0in - {.tongue_reach}","via":"harvest"}}]},"top_above_axis":{"label":"Its top above the bore axis","kind":"length","measurements":[{"id":"photo","value":1.16,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-carbine 94b9fe2cb318 (Magpul's mag538-fde_04: the FDE hand guard on a rifle, its right side seen level)","scaleRef":"its M-LOK slots: 33.65 px/in","method":"the barrel's axis ahead of the front sight base (its silhouette rows 563 to 583 at columns 1000 and 1060: centre 573; 0.62 in across, the barrel's 0.625) to the body's top (row 534): 39 px; ± 1.5 px","via":"harvest"}}]},"bottom_below_axis":{"label":"Its body's bottom (clear of the front lip) below the bore axis","kind":"length","measurements":[{"id":"photo","value":1.16,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-carbine 94b9fe2cb318 (Magpul's mag538-fde_04: the FDE hand guard on a rifle, its right side seen level)","scaleRef":"its M-LOK slots: 33.65 px/in","method":"the barrel's axis (row 573) to the body's bottom (row 612, columns 640 to 830): 39 px; ± 1.5 px","via":"harvest"}}]},"seam_y":{"label":"The seam between its two halves, on the sides, above the bore axis (negative below)","kind":"length","measurements":[{"id":"photo","value":-0.09,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-carbine 94b9fe2cb318 (Magpul's mag538-fde_04: the FDE hand guard on a rifle, its right side seen level)","scaleRef":"its M-LOK slots: 33.65 px/in","method":"the dark line along its side (luminance 120 at row 576, between 139 above and 126 below, column 700), 3 px under the axis; ± 1 px","via":"harvest"}}]},"reach_inside":{"label":"The room inside its M-LOK faces before what runs through it (how far an accessory's nuts may reach in)","kind":"length","measurements":[],"note":"Depends on the barrel, the gas tube and the heat shield, and on the wall, which no view gives: no figure, so the check reads as unmade."},"mlok_side_slots":{"label":"M-LOK slots in each upper side face (the two and ten o'clock rows)","kind":"count","measurements":[{"id":"photo","value":3,"unit":"count","source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-carbine 94b9fe2cb318 (Magpul's mag538-fde_04, the FDE on a rifle, its right side)","scaleRef":"none: a count","method":"three slots in the right side's row; three along each edge from above (11a885bc3699), along the left from below (d4a119f9380f) and on Primary Arms' gray (200bf0744ee8); the instruction sheet draws three on the carbine","via":"harvest"}}]},"mlok_side_slot0_x":{"label":"The side rows' rearmost M-LOK slot (its centre), from its rear flange's end","kind":"length","measurements":[{"id":"photo","value":1.8,"unit":"in","pm":0.07,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-carbine 94b9fe2cb318 (Magpul's mag538-fde_04, the FDE on a rifle, its right side seen level)","scaleRef":"its M-LOK slots: 33.65 px/in","method":"the rearmost slot's centre (column 686.5, between its edges at 665 and 708 at luminance 110) less the tongues' rear edge (607): 79.5 px = 2.36 in, less the tongues' reach (tongue_reach, 0.56); ± 2 px","via":"harvest"}}]},"mlok_side_slot_y":{"label":"The side rows' slot centres above the bore axis","kind":"length","measurements":[{"id":"photo","value":0.46,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-carbine 94b9fe2cb318 (Magpul's mag538-fde_04, the FDE on a rifle, its right side seen level)","scaleRef":"its M-LOK slots: 33.65 px/in","method":"each slot's edges down its middle column (rows 553 to 562 at columns 680 and 740): centre 557.5, 15.5 px over the axis (row 573); ± 1 px","via":"harvest"}}]},"mlok_side_face_angle":{"label":"The side M-LOK faces' outward direction about the bore axis, from straight up (degrees)","kind":"angle","measurements":[{"id":"magpul","value":60,"unit":"deg","stated":"M-LOK slots at the two, six, and ten o'clock positions for mounting MIL-STD-1913 Picatinny rails or other direct-attach M-LOK accessories","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE SL® Hand Guard, Carbine-Length – AR15/M4, Model MAG538: Technical Specifications","url":"https://magpul.com/moeslhandguard-carbine-length-ar15-m4.html","retrieved":"2026-10-28","via":"harvest"}},{"id":"midwest","value":90,"unit":"deg","stated":"Slots at the three, six, and nine o'clock positions for mounting direct-attach M-LOK accessories","source":{"type":"spec","publisher":"retailer","name":"Midwest Gun Works, Magpul MOE SL AR15/M4 Carbine Length Handguard (MAG538-XX)","url":"https://midwestgunworks.com/page/mgwi/prod/mag538-xx","retrieved":"2026-10-28","via":"harvest"}},{"id":"photo","value":70,"unit":"deg","pm":7,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-carbine 11a885bc3699 (Magpul's feature 03: the black hand guard from above, 700 x 525) and 94b9fe2cb318 (the FDE on a rifle, its right side seen level)","scaleRef":"from above, 63.5 px/in at the side faces; level, 33.65 px/in","method":"from above, the side slots show as slits 4 to 12 px across (rows 219 to 234 and 305 to 316: the lens off to one side), 8 px on average, against the slot's 7 mm (std.mlok.slot_width): cos ≈ 0.46, 63° ± 10; level from the side, each slot is 10 px tall, the full 7 mm (9.3 px): a face within 20° of upright. Both hold at 70","via":"harvest"}}],"adopt":{"from":"photo","reason":"Magpul's \"two ... ten o'clock\" says which faces, and Midwest Gun Works says three and nine: the faces stand between, at the angle Magpul's own photos from above and from the side both allow."}},"mlok_side_slot_z":{"label":"The side rows' slot centres out from the rifle's middle plane (the middle of each face's flat)","kind":"length","measurements":[{"id":"derived","value":0.814495,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.width} / 2 - {.face_flat} / 2 * cos({.mlok_side_face_angle})","via":"harvest"}}],"note":"The face's flat runs up from the side at full width (its lower edge), leaning in at the face's angle, its middle where the photo has the slots' centres."},"mlok_axis_y":{"label":"Where the side faces' normals through their slots' centres meet the rifle's middle plane, above the bore axis: the side M-LOK rows' axis","kind":"length","measurements":[{"id":"derived","value":0.1635481,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{.mlok_side_slot_y} - {.mlok_side_slot_z} / tan({.mlok_side_face_angle})","via":"harvest"}}],"note":"The photos have the slots' centres higher on the faces than the foot of a line from the bore square to faces that lean as they do: the faces are angles about this axis instead (the anchor `mlok`), so that an accessory's nuts stand on the slots' centres."},"mlok_side_face_distance":{"label":"The side M-LOK faces' distance from their axis (mlok_axis_y), along their outward direction","kind":"length","measurements":[{"id":"derived","value":0.8667674,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{.mlok_side_slot_z} / sin({.mlok_side_face_angle})","via":"harvest"}}],"note":"From the axis to each slot's centre, square to its face."},"mlok_bottom_slots":{"label":"M-LOK slots in the underside (six o'clock)","kind":"count","measurements":[{"id":"photo","value":4,"unit":"count","source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-carbine d4a119f9380f (Magpul's mag538-gry_02: the gray hand guard upside down, seen from below and its left, 1200 x 1200)","scaleRef":"none: a count","method":"four openings along the underside's middle (row 532: columns 284 to 430, 466 to 610, 649 to 790 and 853 to 954), the last a short one with the shield showing in it, at the M-LOK pitch: three slots and a fourth","via":"harvest"}}]},"mlok_bottom_slot0_x":{"label":"The underside's rearmost M-LOK slot (its centre), from its rear flange's end","kind":"length","measurements":[{"id":"photo","value":1.81,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-carbine d4a119f9380f (Magpul's mag538-gry_02: from below and its left)","scaleRef":"the underside's own slots, 181 px a pitch (114.9 px/in), and the side's, 172.25 (109.4 px/in), each from the photo's middle column (600)","method":"the underside's rearmost slot (column 357) stands 2.115 in behind the middle at its face's scale, the side's (367.5) 2.125 at its own: in line, 0.01 ahead of the side row's (mlok_side_slot0_x)","via":"harvest"}}]},"mlok_bottom_face_distance":{"label":"The underside's M-LOK face, its distance below the bore axis","kind":"length","measurements":[{"id":"derived","value":1.16,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.bottom_below_axis}","via":"harvest"}}]},"rivet0_x":{"label":"The heat shield's rearmost rivet (its head on the underside), from its rear flange's end","kind":"length","measurements":[{"id":"photo","value":1,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-carbine d4a119f9380f (Magpul's mag538-gry_02: from below)","scaleRef":"the underside's slots, 114.9 px/in","method":"a round head at column 265 in the underside's middle, 0.80 in behind the rearmost slot's centre","via":"harvest"}}]},"rivet1_x":{"label":"The heat shield's front rivet (its head on the underside), from its rear flange's end","kind":"length","measurements":[{"id":"photo","value":5.7,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-carbine d4a119f9380f (Magpul's mag538-gry_02: from below)","scaleRef":"the underside's slots, 114.9 px/in","method":"a round head at column 805, between the third and fourth openings: 3.90 in ahead of the rearmost slot's centre","via":"harvest"}}]},"rivet_d":{"label":"A rivet head's diameter","kind":"length","measurements":[{"id":"photo","value":0.13,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-carbine d4a119f9380f (Magpul's mag538-gry_02: from below)","scaleRef":"the underside's slots, 114.9 px/in","method":"each head about 15 px across","via":"harvest"}}]},"rivet_height":{"label":"How far a rivet head stands proud of the underside","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the heads are seen from below only, never in profile.","via":"harvest"}}]},"top_slots":{"label":"The small slots in each row along its top (one row each side of the crown)","kind":"count","measurements":[{"id":"photo","value":8,"unit":"count","source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-carbine 11a885bc3699 (Magpul's feature 03: the black hand guard from above)","scaleRef":"none: a count","method":"eight in each row (rows 242 and 300, columns 115 to 490); eight along the top on Primary Arms' gray (200bf0744ee8) and on Magpul's three-quarter view (8a8452bc4ff3)","via":"harvest"}}]},"top_slot0_x":{"label":"The rearmost top slot's centre, from its rear flange's end","kind":"length","measurements":[{"id":"photo","value":0.29,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-carbine 11a885bc3699 (Magpul's feature 03: the black hand guard from above)","scaleRef":"its side slots seen edge-on, 100.0 px apart for the standard's 40 mm: 63.5 px/in","method":"the rearmost top slot's centre (column 127.5) 96 px behind the side row's rearmost slot's (223.5): 1.51 in behind mlok_side_slot0_x","via":"harvest"}}]},"top_slot_pitch":{"label":"The top slots, centre to centre","kind":"length","measurements":[{"id":"photo","value":0.79,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-carbine 11a885bc3699 (Magpul's feature 03, from above)","scaleRef":"63.5 px/in","method":"the eight centres at 127.5 to 479 px: 50.2 px a pitch (the standard's 20 mm M-LOK interval is 0.787)","via":"harvest"}}]},"top_slot_z":{"label":"Each row of top slots, its centre line from the middle of the top","kind":"length","measurements":[{"id":"photo","value":0.45,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-carbine 11a885bc3699 (Magpul's feature 03, from above)","scaleRef":"63.5 px/in","method":"the rows at 242 and 300 px, the body's middle at 269.5 (its silhouette 215 to 324): 28.5 px each side","via":"harvest"}}]},"top_slot_length":{"label":"Each top slot's length along it","kind":"length","measurements":[{"id":"photo","value":0.37,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-carbine 11a885bc3699 (Magpul's feature 03, from above)","scaleRef":"63.5 px/in","method":"the dark runs along row 242, 23 to 25 px","via":"harvest"}}]},"top_slot_width":{"label":"Each top slot's width across","kind":"length","measurements":[{"id":"assumed","value":0.12,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: from above the carbine's top slots run into the shadows of the panels round them; about a third as wide as long, as they show on the Primary Arms gray (200bf0744ee8).","via":"harvest"}}]},"crown_grooves":{"label":"The grooves along its crown, between the two rows of top slots","kind":"count","measurements":[{"id":"photo","value":8,"unit":"count","source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-carbine 11a885bc3699 (Magpul's feature 03, from above)","scaleRef":"none: a count","method":"eight dark minima across column 330 between rows 262 and 286 (about 3.4 px apart)","via":"harvest"}}]},"crown_groove_span":{"label":"The grooved strip's width across the crown","kind":"length","measurements":[{"id":"photo","value":0.38,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-carbine 11a885bc3699 (Magpul's feature 03, from above)","scaleRef":"63.5 px/in","method":"the first and the last minimum across column 330, rows 262 and 286: 24 px","via":"harvest"}}]},"crown_groove_end_x":{"label":"Where the grooved strip ends at the front, from its rear flange's end","kind":"length","measurements":[{"id":"photo","value":6.85,"unit":"in","pm":0.1,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-carbine 11a885bc3699 (Magpul's feature 03, from above)","scaleRef":"63.5 px/in","method":"the dark strip along row 270 ends at column 544 (its rounded end), 5.05 in ahead of the side row's rearmost slot (223.5 px)","via":"harvest"}}]},"crown_groove_depth":{"label":"Each crown groove's depth","kind":"length","measurements":[{"id":"assumed","value":0.015,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the grooves are seen from above only.","via":"harvest"}}]},"rib_count":{"label":"The upright ribs along each side of the lower half","kind":"count","measurements":[{"id":"photo","value":8,"unit":"count","source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-carbine 94b9fe2cb318 (Magpul's mag538-fde_04, the FDE on a rifle, its right side)","scaleRef":"none: a count","method":"eight lines down the lower half between the window and the front panel (row 593: columns 656.5, 682, 707, 733, 758, 783, 808.5, 834)","via":"harvest"}}]},"rib0_x":{"label":"The rearmost rib, from its rear flange's end","kind":"length","measurements":[{"id":"photo","value":0.91,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-carbine 94b9fe2cb318 (Magpul's mag538-fde_04, the FDE on a rifle, its right side seen level)","scaleRef":"33.65 px/in","method":"column 656.5, 49.5 px ahead of the tongues' rear edge (607) = 1.47 in, less tongue_reach","via":"harvest"}}]},"rib_pitch":{"label":"The ribs, one to the next","kind":"length","measurements":[{"id":"photo","value":0.75,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-carbine 94b9fe2cb318 (Magpul's mag538-fde_04, the FDE on a rifle, its right side seen level)","scaleRef":"33.65 px/in","method":"seven gaps from 656.5 to 834 px: 25.2 px each; from below (d4a119f9380f) the small slots between them are 87.7 px apart, 0.76 to 0.80 in by which face's scale","via":"harvest"}}]},"rib_width":{"label":"Each rib's width","kind":"length","measurements":[{"id":"assumed","value":0.06,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: each rib shows as a lit and a shaded line one or two pixels wide at 33.65 px/in (0.03 to 0.06), and a few pixels on the mid-length's closer photos.","via":"harvest"}}]},"rib_height":{"label":"How far each rib stands from the panels between them","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the ribs cast short shadows in Magpul's close photos of the mid-length (a6cff9cf637f), never seen in profile.","via":"harvest"}}]},"bottom_notches":{"label":"The small slots in each row along the lower edges","kind":"count","measurements":[{"id":"photo","value":10,"unit":"count","source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-carbine d4a119f9380f (Magpul's mag538-gry_02: from below and its left)","scaleRef":"none: a count","method":"ten along row 601 (columns 176 to 1004), between the ribs and on under the front panel","via":"harvest"}}]},"bottom_notch0_x":{"label":"The rearmost lower-edge slot's centre, from its rear flange's end","kind":"length","measurements":[{"id":"photo","value":0.27,"unit":"in","pm":0.1,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-carbine d4a119f9380f (Magpul's mag538-gry_02: from below and its left)","scaleRef":"between the side face's 109.4 and the underside's 114.9 px/in, 112","method":"column 196.5, 171 px behind the side row's rearmost slot (367.5): 1.53 in behind mlok_side_slot0_x","via":"harvest"}}]},"bottom_notch_pitch":{"label":"The lower-edge slots, centre to centre","kind":"length","measurements":[{"id":"photo","value":0.78,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-carbine d4a119f9380f (Magpul's mag538-gry_02: from below)","scaleRef":"112 px/in","method":"ten centres from 196.5 to 985.5 px: 87.7 px a pitch","via":"harvest"}}]},"bottom_notch_length":{"label":"Each lower-edge slot's length","kind":"length","measurements":[{"id":"photo","value":0.36,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-carbine d4a119f9380f (Magpul's mag538-gry_02: from below)","scaleRef":"112 px/in","method":"the dark runs along row 601: 38 to 42 px","via":"harvest"}}]},"bottom_notch_width":{"label":"Each lower-edge slot's width","kind":"length","measurements":[{"id":"assumed","value":0.1,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the slots show about a quarter as wide as long from below, at an angle the photo doesn't give.","via":"harvest"}}]},"notch_depth":{"label":"How deep the top and lower-edge slots go (they are blind)","kind":"length","measurements":[{"id":"assumed","value":0.06,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view shows one in section; they show their own colour inside, not the barrel.","via":"harvest"}}]},"wall":{"label":"Its polymer wall's thickness","kind":"length","measurements":[{"id":"assumed","value":0.15,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows an end square on or a section. Taken so that the model comes near Magpul's 6.7 oz at the polymer's density on file (std.density.polymer) with its aluminium heat shield; what it still lacks is the inner ribs and bosses no view shows.","via":"harvest"}}]},"heat_shield_thickness":{"label":"Its aluminium heat shield's thickness","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the shield shows edge-on only in Magpul's feature 04 (d70407049a05), a bright sheet a few pixels thick at 700 px for the hand guard's half.","via":"harvest"}}]},"seam_groove":{"label":"The seam's groove along each side (its width and its depth)","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the seam shows as a dark line one pixel wide at 33.65 px to the inch, its depth on no view.","via":"harvest"}}]},"face_flat":{"label":"Each upper side face's flat (where its M-LOK slots are), its height across the face","kind":"length","measurements":[{"id":"assumed","value":0.5,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the slot's 7 mm and a margin each side, as Primary Arms' gray (200bf0744ee8) shows the face round its slots.","via":"harvest"}}]},"top_half_width":{"label":"Its top's flat (the crown with its two rows of slots), half its width","kind":"length","measurements":[{"id":"assumed","value":0.6,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no end view on file; from above, the two rows of top slots stand 0.45 either side of the middle, seen whole (not foreshortened), so the top is near flat that far out and a little more.","via":"harvest"}}]},"bottom_half_width":{"label":"Its underside's flat (where the six o'clock slots are), half its width","kind":"length","measurements":[{"id":"assumed","value":0.42,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no end view; from below (d4a119f9380f) the underside's flat holds its M-LOK slots with a margin each side, rounding into the sides at the lower-edge slots.","via":"harvest"}}]},"lower_round_y":{"label":"Where the side rounds under into the underside, above the bore axis (negative below)","kind":"length","measurements":[{"id":"assumed","value":-0.78,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the lower-edge slots are on the round, seen from the side as notches along the bottom edge and from below as a row beside the underside's slots.","via":"harvest"}}]},"front_flange_od":{"label":"Its front flange (what goes into the round cap), outside diameter","kind":"length","measurements":[{"id":"assumed","value":1.36,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: Magpul's instructions slide the flange \"into the metal hand guard cap\"; no view shows it. Taken inside the round cap on file (bcm-handguard-cap-round-750, its tabs at 3 and 9 o'clock to 0.690 from the axis).","via":"harvest"}}]},"front_flange_length":{"label":"Its front flange's length (into the cap)","kind":"length","measurements":[{"id":"assumed","value":0.42,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view shows the flange from the side. Long enough that the front wall it stands from stays behind the round cap's rim with the flange home (the cap is 0.276 deep).","via":"harvest"}}]},"rear_collar_od":{"label":"Its rear flanges (what stands in the delta ring's skirt), outside diameter","kind":"length","measurements":[{"id":"assumed","value":1.72,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the flanges stand in the delta ring's skirt (std.ar15.slip_ring_skirt_d, 1.750 inside) and show on no photo; taken 0.03 under the skirt.","via":"harvest"}}]},"ring_clearance":{"label":"The room between the tongues and the delta ring they reach back over","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the tongues stand over the ring (std.ar15.slip_ring_od, 2.1) and their inside is seen on no photo.","via":"harvest"}}]},"front_wall_x":{"label":"Its front wall (the inner face the front flange stands from), from its rear flange's end","kind":"length","measurements":[{"id":"derived","value":6.03,"unit":"in","pm":0.12,"source":{"type":"derived","expr":"{.mounting_length} - {.front_flange_length} - {.wall}","via":"harvest"}}],"note":"Ahead of the wall the shell runs on as its side extensions and its front lip, open over the top, round the cap and the front sight base (\"Hand Guard will wrap around the front sight when mounted\")."},"front_width":{"label":"Its front panel's width (it stands out from the body round the cap and the front sight base)","kind":"length","measurements":[{"id":"photo","value":1.99,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-carbine 11a885bc3699 (Magpul's feature 03: the black hand guard from above)","scaleRef":"the body's width beside it, Magpul's 1.8 in (width), at the same depth","method":"the front panel's silhouette across, rows 210 to 334 at columns 540 to 610: 125 px, against the body's 113 (rows 215 to 327 at column 450): 1.106 times Magpul's width","via":"harvest"}}]},"front_flare_x":{"label":"Where the front panel stands out from the body, from its rear flanges' end","kind":"length","measurements":[{"id":"photo","value":6.19,"unit":"in","pm":0.1,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-carbine 11a885bc3699 (Magpul's feature 03: the black hand guard from above)","scaleRef":"its side slots seen edge-on: 63.5 px/in","method":"the silhouette's step out along row 211 at column 502, 4.39 in ahead of the side row's rearmost slot (223.5 px)","via":"harvest"}}]},"front_room_d":{"label":"The room inside its front panel round the hand guard cap","kind":"length","measurements":[{"id":"derived","value":1.7329,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{bcm-handguard-cap-round-750.lip_od} + 2 * {.ring_clearance}","via":"harvest"}}],"note":"The front panel wraps the round cap (\"Hand Guard will wrap around the front sight when mounted\"): its inside is the cap's own outside and a clearance (ring_clearance), the one round cap on file."},"nose_corner_x":{"label":"The round at the top of its front edge (where the side extensions' level top turns down the front), its length along","kind":"length","measurements":[{"id":"photo","value":0.12,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-carbine c654e781f876 (Magpul's mag538-blk_04: the black hand guard on a rifle, its right side seen level; the same pose as the Flat Dark Earth one traced)","scaleRef":"33.65 px/in by its M-LOK slots (the FDE photo's pose)","method":"the level top's edge ends and the round begins 4 px behind the front edge (by eye on a crop at 3 to 5 times; the front sight base's front leg stands just ahead of it)","via":"harvest"}}],"note":"The traced outline's corner here is the front sight's leg's, not the part's: the model draws this round instead (clean_nose in the script)."},"nose_corner_y":{"label":"The same round's height down the front edge","kind":"length","measurements":[{"id":"photo","value":0.24,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-carbine c654e781f876 (Magpul's mag538-blk_04: the black hand guard on a rifle, its right side seen level; the same pose as the Flat Dark Earth one traced)","scaleRef":"33.65 px/in by its M-LOK slots (the FDE photo's pose)","method":"the front edge runs straight from 8 px under the level top (by eye on the same crop)","via":"harvest"}}]}}},{"subject":"magpul-moe-sl-handguard-mid","title":"Magpul MOE SL® Hand Guard, Mid-Length – AR15/M4 (MAG551)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"magpul","value":8.3,"unit":"oz","stated":"Weight 8.3 oz.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE SL® Hand Guard, Mid-Length – AR15/M4, Model MAG551: Technical Specifications","url":"https://magpul.com/moeslhandguard-mid-length-ar15-m4.html","retrieved":"2026-10-28","via":"harvest"}},{"id":"primary-arms","value":8.3,"unit":"oz","stated":"Weight 8.3 oz.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Magpul MOE SL Drop In AR-15 Handguard - M-LOK - Mid-Length - FDE (MAG551-FDE)","url":"https://www.primaryarms.com/magpul-moe-sl-handguard-mid-length-flat-dark-earth-mag551-fde","retrieved":"2026-10-28","via":"harvest"}}],"adopt":{"from":"magpul","reason":"The maker's figure; Primary Arms' page states the same."},"note":"The two halves together, the lower one with its riveted aluminium heat shield. (KY Gun Co's page gives \"Weight 2 lb\": a shipping weight, left out.)"},"length":{"label":"Length, maximum","kind":"length","measurements":[{"id":"magpul","value":10.9,"unit":"in","pm":0.05,"stated":"Length, max 10.9 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE SL® Hand Guard, Mid-Length – AR15/M4, Model MAG551: Technical Specifications","url":"https://magpul.com/moeslhandguard-mid-length-ar15-m4.html","retrieved":"2026-10-28","via":"harvest"}},{"id":"primary-arms","value":10.9,"unit":"in","pm":0.05,"stated":"Handguard Length 10.9","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Magpul MOE SL Drop In AR-15 Handguard - M-LOK - Mid-Length - FDE (MAG551-FDE)","url":"https://www.primaryarms.com/magpul-moe-sl-handguard-mid-length-flat-dark-earth-mag551-fde","retrieved":"2026-10-28","via":"harvest"}},{"id":"photo","value":10.86,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-mid fa1c10e48cd7 (Magpul's mag551-odg_03: the OD green hand guard on a rifle, the rifle's right side seen level, 1200 x 1200)","scaleRef":"its four M-LOK slots, centres 390.5, 503.5, 615.5 and 729.5 px: 113.0 px for the standard's 40 mm (std.mlok.slot_pitch), 71.75 px/in","method":"the outline from the tongues' rear over the delta ring (column 196) to the side extensions' front tip (975): 779 px; ± 1.5 px at each end","via":"harvest"}}],"adopt":{"from":"magpul","reason":"The maker's figure; the photo, scaled by the standard's M-LOK pitch and by nothing of the part, agrees within 0.04 in (0.4%)."},"note":"From the rear end of the tongues that reach back over the delta ring to the tip of the side extensions, which wrap the front sight base (\"Front lip and long side extensions shields hand from hot sight assembly\")."},"mounting_length":{"label":"Length, mounting (from its rear flanges' end on the delta ring's lip to its front flange's end in the cap)","kind":"length","measurements":[{"id":"assumed","value":8.6,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading of this hand guard: Magpul's page gives no mounting length for MAG551. Magpul gives 8.6 in for its MOE M-LOK mid-length (MAG426, \"Length, mounting: 8.6 in.\"), and for its two carbine lengths the same 6.6 in (MOE SL MAG538 and MOE M-LOK MAG424): the span a rifle's delta ring and cap hold a drop-in hand guard between, which the gas system's length sets, not the hand guard. The photo bears it out: the front sight base's rear (its tower's front leg at column 973 less the base's 1.804 in, bcm-front-sight-base-f-750.length) stands 8.47 in ahead of the bearing face read there, so the flange's end goes 0.13 past the cap's floor, which the ring's spring takes up.","via":"harvest"}}]},"width":{"label":"Width","kind":"length","measurements":[{"id":"magpul","value":1.8,"unit":"in","pm":0.05,"stated":"Width 1.8 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE SL® Hand Guard, Mid-Length – AR15/M4, Model MAG551: Technical Specifications","url":"https://magpul.com/moeslhandguard-mid-length-ar15-m4.html","retrieved":"2026-10-28","via":"harvest"}},{"id":"magpul-features","value":1.8,"unit":"in","pm":0.05,"stated":"1/3\" (15%) NARROWER PROFILE THAN ORIGINAL MOE (1.8\" RATHER THAN 2.2\")","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE SL® Hand Guard, Mid-Length – AR15/M4, Model MAG551: Technical Specifications","url":"https://magpul.com/moeslhandguard-mid-length-ar15-m4.html","retrieved":"2026-10-28","via":"harvest"}},{"id":"photo","value":1.75,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-mid e31d01d48eb3 (Magpul's feature 03 for MAG551: the black hand guard on a rifle from above, 700 x 525)","scaleRef":"its side M-LOK slots seen edge-on along each edge and its top slots: the side rows' 95.5 px for the standard's 40 mm, 60.6 px/in at the side faces","method":"the body's silhouette across, rows 213 to 318 at column 300: 106 px; its sides are further from a lens above than its top, so it reads narrow","via":"harvest"}}],"adopt":{"from":"magpul","reason":"The maker's figure, said twice on its page; the view from above, scaled at the side faces' depth, reads 3% less, as a lens close above it would."}},"height":{"label":"Height","kind":"length","measurements":[{"id":"magpul","value":2.4,"unit":"in","pm":0.05,"stated":"Height: 2.4 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE SL® Hand Guard, Mid-Length – AR15/M4, Model MAG551: Technical Specifications","url":"https://magpul.com/moeslhandguard-mid-length-ar15-m4.html","retrieved":"2026-10-28","via":"harvest"}},{"id":"photo","value":2.32,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-mid fa1c10e48cd7 (Magpul's mag551-odg_03: the OD green hand guard on a rifle, its right side seen level)","scaleRef":"its M-LOK slots at the standard's pitch: 71.75 px/in","method":"the body's top (row 361) to its bottom (527.5) clear of the front lip and the grip, columns 250 to 830: 166.5 px; ± 1 px each edge","via":"harvest"}}],"adopt":{"from":"photo","reason":"The model is drawn from the traced outline, at the photo's height. Magpul's 2.4 is 3% more, beyond the photo's ±; what it measures over isn't said (the front lip reaches lower). The carbine's own photo reads 2.32 too."}},"inside_diameter":{"label":"Inside diameter","kind":"length","measurements":[],"note":"Magpul gives none. The model's inside is its outside less the wall (wall), which no view gives either."},"rear_x":{"label":"Its rear flanges' end (bearing on the delta ring's lip) ahead of the receiver's front face","kind":"length","measurements":[{"id":"derived","value":0.336,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{std.ar15.slip_ring_front_x}","via":"harvest"}}],"note":"Where the standard's delta ring holds it (std.ar15.slip_ring_front_x, from the Army's drawings): its rear flanges in the ring's skirt, against the lip. Its instruction sheet: \"When both halves are in place, make sure your delta ring is securing BOTH upper and lower rear flanges of the Hand Guards\"."},"window_length":{"label":"The window in each side of its rear end, where the delta ring shows: from the tongues' rear end to the window's front edge","kind":"length","measurements":[{"id":"photo","value":0.68,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-mid fa1c10e48cd7 (Magpul's mag551-odg_03: the OD green hand guard on a rifle, its right side seen level)","scaleRef":"its M-LOK slots: 71.75 px/in","method":"the tongues' rear edge (column 196) to the window's front edge, where the black ring's cone ends (242.5) and the body's side begins (245): 49 px; ± 2 px","via":"harvest"}}],"note":"The ring fills the window in every photo of it on a rifle: its front edge is where the ring's front end is."},"tongue_reach":{"label":"How far the tongues reach back over the delta ring behind its rear flanges' end","kind":"length","measurements":[{"id":"derived","value":0.56,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.window_length} - {std.ar15.slip_ring_skirt_length}","via":"harvest"}}],"note":"The window's front edge is the ring's front end, which stands the ring's skirt ahead of the lip the flanges bear on (std.ar15.slip_ring_skirt_length)."},"outline_rear_x":{"label":"The tongues' rear end (where the side outline begins), from its rear flanges' end","kind":"length","measurements":[{"id":"derived","value":-0.56,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"0in - {.tongue_reach}","via":"harvest"}}]},"top_above_axis":{"label":"Its top above the bore axis","kind":"length","measurements":[{"id":"photo","value":1.14,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-mid fa1c10e48cd7 (Magpul's mag551-odg_03: the OD green hand guard on a rifle, its right side seen level)","scaleRef":"its M-LOK slots: 71.75 px/in","method":"the barrel's axis ahead of the front sight base (its silhouette rows 418 to 468 at columns 1100 and 1150: centre 443) to the body's top (row 361): 82 px; ± 1 px","via":"harvest"}}]},"bottom_below_axis":{"label":"Its body's bottom (clear of the front lip) below the bore axis","kind":"length","measurements":[{"id":"photo","value":1.18,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-mid fa1c10e48cd7 (Magpul's mag551-odg_03: the OD green hand guard on a rifle, its right side seen level)","scaleRef":"its M-LOK slots: 71.75 px/in","method":"the barrel's axis (row 443) to the body's bottom (row 527.5, columns 250 to 550 and 670 to 830, clear of the grip): 84.5 px; ± 1 px","via":"harvest"}}]},"seam_y":{"label":"The seam between its two halves, on the sides, above the bore axis (negative below)","kind":"length","measurements":[{"id":"photo","value":-0.1,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-mid fa1c10e48cd7 (Magpul's mag551-odg_03: the OD green hand guard on a rifle, its right side seen level)","scaleRef":"its M-LOK slots: 71.75 px/in","method":"the dark line along its side (luminance 67 at row 449 to 450 between 88 above and 90 below, column 300), 7 px under the axis; ± 1 px","via":"harvest"}}]},"reach_inside":{"label":"The room inside its M-LOK faces before what runs through it (how far an accessory's nuts may reach in)","kind":"length","measurements":[],"note":"Depends on the barrel, the gas tube and the heat shield, and on the wall, which no view gives: no figure, so the check reads as unmade."},"mlok_side_slots":{"label":"M-LOK slots in each upper side face (the two and ten o'clock rows)","kind":"count","measurements":[{"id":"photo","value":4,"unit":"count","source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-mid fa1c10e48cd7 (Magpul's mag551-odg_03, the OD green on a rifle, its right side)","scaleRef":"none: a count","method":"four slots in the right side's row; four along each edge from above (e31d01d48eb3), on the left on a rifle (4a086f17a6c7) and on Primary Arms' Flat Dark Earth (5ae353ae419f); the instruction sheet draws four on the mid-length","via":"harvest"}}]},"mlok_side_slot0_x":{"label":"The side rows' rearmost M-LOK slot (its centre), from its rear flanges' end","kind":"length","measurements":[{"id":"photo","value":2.15,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-mid fa1c10e48cd7 (Magpul's mag551-odg_03, the OD green on a rifle, its right side seen level)","scaleRef":"its M-LOK slots: 71.75 px/in","method":"the rearmost slot's centre (column 390.5, between its edges at 345 and 436 at luminance 45) less the tongues' rear edge (196): 194.5 px = 2.71 in, less the tongues' reach (tongue_reach, 0.56); ± 1.5 px","via":"harvest"}}]},"mlok_side_slot_y":{"label":"The side rows' slot centres above the bore axis","kind":"length","measurements":[{"id":"photo","value":0.43,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-mid fa1c10e48cd7 (Magpul's mag551-odg_03, the OD green on a rifle, its right side seen level)","scaleRef":"its M-LOK slots: 71.75 px/in","method":"each slot's edges down its middle column (rows 401 to 422 at columns 430 and 600): centre 411.5, 31.5 px over the axis (row 443); ± 1 px","via":"harvest"}}]},"mlok_side_face_angle":{"label":"The side M-LOK faces' outward direction about the bore axis, from straight up (degrees)","kind":"angle","measurements":[{"id":"magpul","value":60,"unit":"deg","stated":"M-LOK® slots at two, six, and ten o'clock for accessories","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, MOE SL® Hand Guard, Mid-Length – AR15/M4, Model MAG551: Technical Specifications","url":"https://magpul.com/moeslhandguard-mid-length-ar15-m4.html","retrieved":"2026-10-28","via":"harvest"}},{"id":"photo","value":76,"unit":"deg","pm":7,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-mid e31d01d48eb3 (Magpul's feature 03: the black hand guard on a rifle from above) and fa1c10e48cd7 (the OD green on a rifle, its right side seen level)","scaleRef":"from above, 60.6 px/in at the side faces; level, 71.75 px/in","method":"from above, the side slots show as slits 3 to 5 px across (rows 218 to 222 and 313 to 315 at columns 166, 262 and 357), 4 px against the slot's 7 mm (std.mlok.slot_width, 16.7 px): cos ≈ 0.24, 76°; level from the side each slot is 21 px tall, the full 7 mm (19.8 px): a face within 20° of upright","via":"harvest"}}],"adopt":{"from":"photo","reason":"Magpul's \"two ... ten o'clock\" says which faces, not their angle: its own photos from above and from the side both have them nearer upright."}},"mlok_side_slot_z":{"label":"The side rows' slot centres out from the rifle's middle plane (the middle of each face's flat)","kind":"length","measurements":[{"id":"derived","value":0.8395195,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.width} / 2 - {.face_flat} / 2 * cos({.mlok_side_face_angle})","via":"harvest"}}],"note":"The face's flat runs up from the side at full width (its lower edge), leaning in at the face's angle, its middle where the photo has the slots' centres."},"mlok_axis_y":{"label":"Where the side faces' normals through their slots' centres meet the rifle's middle plane, above the bore axis: the side M-LOK rows' axis","kind":"length","measurements":[{"id":"derived","value":0.2206843,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{.mlok_side_slot_y} - {.mlok_side_slot_z} / tan({.mlok_side_face_angle})","via":"harvest"}}],"note":"The photos have the slots' centres higher on the faces than the foot of a line from the bore square to faces that lean as they do: the faces are angles about this axis instead (the anchor `mlok`), so that an accessory's nuts stand on the slots' centres."},"mlok_side_face_distance":{"label":"The side M-LOK faces' distance from their axis (mlok_axis_y), along their outward direction","kind":"length","measurements":[{"id":"derived","value":0.8652203,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{.mlok_side_slot_z} / sin({.mlok_side_face_angle})","via":"harvest"}}],"note":"From the axis to each slot's centre, square to its face."},"mlok_bottom_slots":{"label":"M-LOK slots in the underside (six o'clock)","kind":"count","measurements":[{"id":"assumed","value":4,"unit":"count","source":{"type":"derived","expr":"{.mlok_side_slots}","basis":"An assumption for the drawing, not a reading: Magpul's page states slots at six o'clock and its photos have a vertical grip on them (c706e2992834), but no view on file looks at the mid-length's underside. The side rows' count and places are taken (the carbine's underside has one more than its sides, on its own photo from below).","via":"harvest"}}]},"mlok_bottom_slot0_x":{"label":"The underside's rearmost M-LOK slot (its centre), from its rear flanges' end","kind":"length","measurements":[{"id":"assumed","value":2.15,"unit":"in","pm":0.5,"source":{"type":"derived","expr":"{.mlok_side_slot0_x}","basis":"An assumption for the drawing, not a reading: in line with the side rows (mlok_bottom_slots).","via":"harvest"}}]},"mlok_bottom_face_distance":{"label":"The underside's M-LOK face, its distance below the bore axis","kind":"length","measurements":[{"id":"derived","value":1.18,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{.bottom_below_axis}","via":"harvest"}}]},"top_slots":{"label":"The small slots in each row along its top (one row each side of the crown)","kind":"count","measurements":[{"id":"photo","value":10,"unit":"count","source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-mid e31d01d48eb3 (Magpul's feature 03: the black hand guard on a rifle from above)","scaleRef":"none: a count","method":"ten in each row (rows 240 and 296, columns 56 to 513); ten along the top edge in the level photo (c706e2992834) and on Primary Arms' Flat Dark Earth (5ae353ae419f)","via":"harvest"}}]},"top_slot0_x":{"label":"The rearmost top slot's centre, from its rear flanges' end","kind":"length","measurements":[{"id":"photo","value":0.52,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-mid e31d01d48eb3 (Magpul's feature 03: from above)","scaleRef":"its side slots seen edge-on, 95.5 px apart for the standard's 40 mm: 60.6 px/in","method":"the rearmost top slot's centre (column 67) 99 px behind the side row's rearmost slot's (166): 1.63 in behind mlok_side_slot0_x","via":"harvest"}}]},"top_slot_pitch":{"label":"The top slots, centre to centre","kind":"length","measurements":[{"id":"photo","value":0.8,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-mid e31d01d48eb3 (Magpul's feature 03: from above)","scaleRef":"60.6 px/in","method":"the ten centres at 67 to 503 px in both rows: 48.4 px a pitch (the standard's 20 mm M-LOK interval is 0.787)","via":"harvest"}}]},"top_slot_z":{"label":"Each row of top slots, its centre line from the middle of the top","kind":"length","measurements":[{"id":"photo","value":0.46,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-mid e31d01d48eb3 (Magpul's feature 03: from above)","scaleRef":"60.6 px/in","method":"the rows at 240 and 296 px, the body's middle at 265.5 (its silhouette 213 to 318): 28 px each side","via":"harvest"}}]},"top_slot_length":{"label":"Each top slot's length along it","kind":"length","measurements":[{"id":"photo","value":0.36,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-mid e31d01d48eb3 (Magpul's feature 03: from above)","scaleRef":"60.6 px/in","method":"the dark runs along rows 240 and 296, 21 to 23 px","via":"harvest"}}]},"top_slot_width":{"label":"Each top slot's width across","kind":"length","measurements":[{"id":"photo","value":0.115,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-mid e31d01d48eb3 (Magpul's feature 03: from above)","scaleRef":"60.6 px/in","method":"the slot at column 262 across, rows 237 to 243: 7 px","via":"harvest"}}]},"crown_grooves":{"label":"The grooves along its crown, between the two rows of top slots","kind":"count","measurements":[{"id":"photo","value":8,"unit":"count","source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-mid e31d01d48eb3 (Magpul's feature 03: from above)","scaleRef":"none: a count","method":"eight dark minima across column 300 between rows 255 and 282 (about 3.4 px apart)","via":"harvest"}}]},"crown_groove_span":{"label":"The grooved strip's width across the crown","kind":"length","measurements":[{"id":"photo","value":0.4,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-mid e31d01d48eb3 (Magpul's feature 03: from above)","scaleRef":"60.6 px/in","method":"the first and the last minimum across column 300, rows 258 and 282: 24 px","via":"harvest"}}]},"crown_groove_end_x":{"label":"Where the grooved strip ends at the front, from its rear flanges' end","kind":"length","measurements":[{"id":"photo","value":8.32,"unit":"in","pm":0.1,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-mid e31d01d48eb3 (Magpul's feature 03: from above)","scaleRef":"60.6 px/in","method":"the dark strip along row 268 ends at column 540 (its rounded end), 6.17 in ahead of the side row's rearmost slot (166 px)","via":"harvest"}}]},"crown_groove_depth":{"label":"Each crown groove's depth","kind":"length","measurements":[{"id":"assumed","value":0.015,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the grooves are seen from above only.","via":"harvest"}}]},"rib_count":{"label":"The upright ribs along each side of the lower half","kind":"count","measurements":[{"id":"photo","value":9,"unit":"count","source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-mid fa1c10e48cd7 (Magpul's mag551-odg_03, the OD green on a rifle, its right side)","scaleRef":"none: a count","method":"nine lines down the lower half between the window and the front panel (row 470: columns 301, 357.5, 413.5, 470.5, 527, 583.5, 640, 696.5, 753.5); nine on the close photo of its side (a6cff9cf637f)","via":"harvest"}}]},"rib0_x":{"label":"The rearmost rib, from its rear flanges' end","kind":"length","measurements":[{"id":"photo","value":0.9,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-mid fa1c10e48cd7 (Magpul's mag551-odg_03, the OD green on a rifle, its right side seen level)","scaleRef":"71.75 px/in","method":"column 301, 105 px ahead of the tongues' rear edge (196) = 1.46 in, less tongue_reach","via":"harvest"}}]},"rib_pitch":{"label":"The ribs, one to the next","kind":"length","measurements":[{"id":"photo","value":0.788,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-mid fa1c10e48cd7 (Magpul's mag551-odg_03, the OD green on a rifle, its right side seen level)","scaleRef":"71.75 px/in","method":"eight gaps from 301 to 753.5 px: 56.6 px each (the standard's 20 mm M-LOK interval is 0.787)","via":"harvest"}}]},"rib_width":{"label":"Each rib's width","kind":"length","measurements":[{"id":"assumed","value":0.06,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: each rib shows as a lit and a shaded line, 4 to 5 px together at 71.75 px/in on the close photo of its side (a6cff9cf637f).","via":"harvest"}}]},"rib_height":{"label":"How far each rib stands from the panels between them","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the ribs cast short shadows in Magpul's close photo of its side (a6cff9cf637f), never seen in profile.","via":"harvest"}}]},"bottom_notches":{"label":"The small slots in each row along the lower edges","kind":"count","measurements":[{"id":"photo","value":13,"unit":"count","source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-mid c706e2992834 (Magpul's mag551-blk_03: the black hand guard on a rifle, its right side seen level)","scaleRef":"none: a count","method":"thirteen notches along the bottom edge, one between each two ribs and on under the front panel (columns 268 to 950, by eye on a crop at 1.9 times)","via":"harvest"}}]},"bottom_notch0_x":{"label":"The rearmost lower-edge slot's centre, from its rear flanges' end","kind":"length","measurements":[{"id":"photo","value":0.51,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-mid fa1c10e48cd7 (Magpul's mag551-odg_03, its right side seen level)","scaleRef":"71.75 px/in","method":"the notches stand between the ribs (one between the ribs at 413.5 and 470.5 px has its ends at 424 and 458, centred at 441): the first between the window's front edge (245) and the first rib (301), at 273, = 0.51 from the bearing face","via":"harvest"}}]},"bottom_notch_pitch":{"label":"The lower-edge slots, centre to centre","kind":"length","measurements":[{"id":"derived","value":0.788,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{.rib_pitch}","via":"harvest"}}],"note":"One between each two ribs: the ribs' pitch."},"bottom_notch_length":{"label":"Each lower-edge slot's length","kind":"length","measurements":[{"id":"photo","value":0.47,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-mid fa1c10e48cd7 (Magpul's mag551-odg_03, its right side seen level)","scaleRef":"71.75 px/in","method":"the notch between the ribs at 413.5 and 470.5 px, its ends at 424 and 458: 34 px","via":"harvest"}}]},"bottom_notch_width":{"label":"Each lower-edge slot's width","kind":"length","measurements":[{"id":"assumed","value":0.1,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the notches show edge-on along the bottom edge from the side, a few pixels tall.","via":"harvest"}}]},"notch_depth":{"label":"How deep the top and lower-edge slots go (they are blind)","kind":"length","measurements":[{"id":"assumed","value":0.06,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view shows one in section; from above they show dark, not the barrel.","via":"harvest"}}]},"wall":{"label":"Its polymer wall's thickness","kind":"length","measurements":[{"id":"assumed","value":0.15,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows an end square on or a section. Taken so that the model comes near Magpul's 8.3 oz at the polymer's density on file (std.density.polymer) with its aluminium heat shield; what it still lacks is the inner ribs and bosses no view shows.","via":"harvest"}}]},"heat_shield_thickness":{"label":"Its aluminium heat shield's thickness","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: Magpul's feature 04 (70b6f543f381) shows the lower half with its shield, edge-on a few pixels thick.","via":"harvest"}}]},"seam_groove":{"label":"The seam's groove along each side (its width and its depth)","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the seam shows as a dark line one or two pixels wide at 71.75 px to the inch, its depth on no view.","via":"harvest"}}]},"face_flat":{"label":"Each upper side face's flat (where its M-LOK slots are), its height across the face","kind":"length","measurements":[{"id":"assumed","value":0.5,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the slot's 7 mm and a margin each side, as the close photo of its side (a6cff9cf637f) shows the face round its slots.","via":"harvest"}}]},"top_half_width":{"label":"Its top's flat (the crown with its two rows of slots), half its width","kind":"length","measurements":[{"id":"assumed","value":0.6,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no end view on file; from above, the two rows of top slots stand 0.46 either side of the middle, seen whole (not foreshortened), so the top is near flat that far out and a little more.","via":"harvest"}}]},"bottom_half_width":{"label":"Its underside's flat (where the six o'clock slots are), half its width","kind":"length","measurements":[{"id":"assumed","value":0.42,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view looks at the mid-length's underside; wide enough for its M-LOK slots and a margin each side, rounding into the sides at the lower-edge slots.","via":"harvest"}}]},"lower_round_y":{"label":"Where the side rounds under into the underside, above the bore axis (negative below)","kind":"length","measurements":[{"id":"assumed","value":-0.8,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the lower-edge slots are on the round, seen from the side as notches along the bottom edge (c706e2992834).","via":"harvest"}}]},"front_flange_od":{"label":"Its front flange (what goes into the round cap), outside diameter","kind":"length","measurements":[{"id":"assumed","value":1.36,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: Magpul's instructions slide the flange \"into the metal hand guard cap\"; no view shows it. Taken inside the round cap on file (bcm-handguard-cap-round-750, its tabs at 3 and 9 o'clock to 0.690 from the axis).","via":"harvest"}}]},"front_flange_length":{"label":"Its front flange's length (into the cap)","kind":"length","measurements":[{"id":"assumed","value":0.42,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view shows the flange from the side. Long enough that the front wall it stands from stays behind the round cap's rim with the flange home (the cap is 0.276 deep).","via":"harvest"}}]},"rear_collar_od":{"label":"Its rear flanges (what stands in the delta ring's skirt), outside diameter","kind":"length","measurements":[{"id":"assumed","value":1.72,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the flanges stand in the delta ring's skirt (std.ar15.slip_ring_skirt_d, 1.750 inside) and show on no photo; taken 0.03 under the skirt.","via":"harvest"}}]},"ring_clearance":{"label":"The room between the tongues and the delta ring they reach back over","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the tongues stand over the ring (std.ar15.slip_ring_od, 2.1) and their inside is seen on no photo.","via":"harvest"}}]},"front_wall_x":{"label":"Its front wall (the inner face the front flange stands from), from its rear flanges' end","kind":"length","measurements":[{"id":"derived","value":8.03,"unit":"in","pm":0.15,"source":{"type":"derived","expr":"{.mounting_length} - {.front_flange_length} - {.wall}","via":"harvest"}}],"note":"Ahead of the wall the shell runs on as its side extensions and its front lip, open over the top, round the cap and the front sight base (\"Hand Guard will wrap around the front sight when mounted\")."},"front_width":{"label":"Its front panel's width (it stands out from the body round the cap and the front sight base)","kind":"length","measurements":[{"id":"photo","value":1.97,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-mid e31d01d48eb3 (Magpul's feature 03: the black hand guard on a rifle from above)","scaleRef":"the body's width beside it, Magpul's 1.8 in (width), at the same depth","method":"the front panel's silhouette across, rows 206 to 323 at columns 560 and 600: 118 px, against the body's 108 (rows 211 to 318 at column 480): 1.093 times Magpul's width","via":"harvest"}}]},"front_flare_x":{"label":"Where the front panel stands out from the body, from its rear flanges' end","kind":"length","measurements":[{"id":"photo","value":7.99,"unit":"in","pm":0.1,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-mid e31d01d48eb3 (Magpul's feature 03: the black hand guard on a rifle from above)","scaleRef":"its side slots seen edge-on: 60.6 px/in","method":"the silhouette's step out along rows 210 and 322 at columns 516 and 525 (520.5), 5.85 in ahead of the side row's rearmost slot (166 px)","via":"harvest"}}]},"front_room_d":{"label":"The room inside its front panel round the hand guard cap","kind":"length","measurements":[{"id":"derived","value":1.7329,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{bcm-handguard-cap-round-750.lip_od} + 2 * {.ring_clearance}","via":"harvest"}}],"note":"The front panel wraps the round cap (\"Hand Guard will wrap around the front sight when mounted\"): its inside is the cap's own outside and a clearance (ring_clearance), the one round cap on file."},"nose_corner_x":{"label":"The round at the top of its front edge (where the side extensions' level top turns down the front), its length along","kind":"length","measurements":[{"id":"photo","value":0.15,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-mid c706e2992834 (Magpul's mag551-blk_03: the black hand guard on a rifle, its right side seen level; the photograph the OD green one traced is recoloured from)","scaleRef":"71.75 px/in by its M-LOK slots","method":"the level top's edge ends and the round begins 11 px behind the front edge (by eye on a crop at 3 to 5 times; the front sight base's front leg stands just ahead of it)","via":"harvest"}}],"note":"The traced outline's corner here is the front sight's leg's, not the part's: the model draws this round instead (clean_nose in the script)."},"nose_corner_y":{"label":"The same round's height down the front edge","kind":"length","measurements":[{"id":"photo","value":0.23,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/magpul-moe-sl-handguard-mid c706e2992834 (Magpul's mag551-blk_03: the black hand guard on a rifle, its right side seen level; the photograph the OD green one traced is recoloured from)","scaleRef":"71.75 px/in by its M-LOK slots","method":"the front edge runs straight from 17 px under the level top (by eye on the same crop)","via":"harvest"}}]}}},{"subject":"magpul-moe-trigger-guard","title":"Magpul MOE enhanced trigger guard, polymer (MAG1186)","dimensions":{"length_side":{"label":"Overall length in side view","kind":"length","measurements":[{"id":"photo","value":2.297,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-moe-trigger-guard ef1ccb74431e (true side view (Stealth Gray, Wing Tactical), 1280 px)","scaleRef":"frame from the reviewed holes front_ear (1140.5,579.5) r=29px, rear_ear (221.5,586.5) r=29px (498.4 px/in, rms 0.000 in over 2 points)","method":"width of the traced outline (tools/trace.py); scaled by the ear holes at the lower's hole spacing","via":"harvest"}},{"id":"trex","value":2.27,"unit":"in","stated":"Length: 2.27 inches","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS","url":"https://www.trex-arms.com/store/magpul-moe-enhanced-trigger-guard-ar-15-m4/","retrieved":"2026-09-30","via":"harvest"}}],"adopt":{"from":"photo","reason":"The traced true side view, scaled by the TDP's 1.844 in hole spacing. T.REX's 2.27 (axis not stated) agrees; before M3 corrected the rear ear hole the photo read 2.164, 5% short."}},"height_side":{"label":"Overall height in side view (ear top to belly bottom)","kind":"length","measurements":[{"id":"photo","value":0.488,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-moe-trigger-guard ef1ccb74431e (true side view (Stealth Gray, Wing Tactical), 1280 px)","scaleRef":"frame from the reviewed holes front_ear (1140.5,579.5) r=29px, rear_ear (221.5,586.5) r=29px (498.4 px/in, rms 0.000 in over 2 points)","method":"height of the traced outline (tools/trace.py); ear top to belly bottom, scaled by the ear holes at the lower's hole spacing","via":"harvest"}}]},"front_ahead_of_hole":{"label":"Front tab's tip ahead of the front ear hole","kind":"length","measurements":[{"id":"photo","value":0.143,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-moe-trigger-guard ef1ccb74431e (true side view (Stealth Gray, Wing Tactical), 1280 px)","scaleRef":"the ear holes at the lower's hole spacing (magpul-moe-trigger-guard.ear_spacing)","method":"x_max of the traced outline (tools/trace.py target)","via":"harvest"}}]},"ear_spacing":{"label":"Ear-hole spacing","kind":"length","measurements":[{"id":"lower","value":1.844,"unit":"in","source":{"type":"derived","expr":"{bad-workhorse-lower.trigger_guard_front_x} - {bad-workhorse-lower.trigger_guard_rear_x}","via":"harvest"},"note":"The guard's ears pin into the lower's ears, so the spacing is the lower's. The guard's side view was calibrated from it."}]},"width_listed":{"label":"Width (retailer listing; axis not defined)","kind":"length","measurements":[{"id":"trex","value":0.62,"unit":"in","stated":"Width: 0.62 inches","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS","url":"https://www.trex-arms.com/store/magpul-moe-enhanced-trigger-guard-ar-15-m4/","retrieved":"2026-09-30","via":"harvest"}}]},"thickness_listed":{"label":"Thickness (retailer listing; axis not defined)","kind":"length","measurements":[{"id":"trex","value":0.15,"unit":"in","stated":"Thickness: 0.15 Inches","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS","url":"https://www.trex-arms.com/store/magpul-moe-enhanced-trigger-guard-ar-15-m4/","retrieved":"2026-09-30","via":"harvest"},"note":"Probably a wall thickness"}]},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"trex","value":6,"unit":"g","stated":"Weight: 0.2 ounces (6 grams)","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS","url":"https://www.trex-arms.com/store/magpul-moe-enhanced-trigger-guard-ar-15-m4/","retrieved":"2026-09-30","via":"harvest"}},{"id":"wing","value":0.18,"unit":"oz","stated":"Weight: 0.18 oz.","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/lower-receiver-parts/lower-receiver-parts/magpul-moe-enhanced-polymer-trigger-guard/","retrieved":"2026-09-30","via":"harvest"}}],"adopt":{"from":"trex","reason":"More precise of two retailer figures (Magpul publishes none); the two agree within rounding."}}}},{"subject":"magpul-pmag-20-gen-m3","title":"Magpul PMAG 20 AR/M4 GEN M3","dimensions":{"overall_height":{"label":"Overall height, feed lips to base","kind":"length","measurements":[{"id":"magpul","value":5.6,"unit":"in","pm":0.1,"stated":"Length, max 5.6 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, PMAG 20 AR/M4 GEN M3 (MAG560), Technical Specifications","url":"https://magpul.com/pmag-20-ar-m4-gen-m3.html","retrieved":"2026-10-13","via":"harvest"}}],"note":"Magpul's 'Length, max', taken as the height from the top of the feed lips to the lowest point of the floorplate with the top section upright, as a magazine well holds it (the patent's side elevation is drawn so). What says it spans that: scaled by it, the patent's side elevation has this magazine's top section, spine to front face, as long as the 30-round GEN M3's (front_to_back: the two readings and their difference are there), and both go into the one standard well. Measured instead along the lean of its lower half it would be a little more; the ± covers that."},"body_height":{"label":"Body height below the feed-lip block","kind":"length","measurements":[],"note":"Onboarding checklist: Side view; overall_height minus the feed-lip block when the block is shared across a product line. Not read: the block is not a piece of its own on a PMAG (the body is one moulding to the lips)."},"feed_lip_block_height":{"label":"Feed-lip block height","kind":"length","measurements":[],"note":"Onboarding checklist. Not read: a PMAG's body is one moulding from the floorplate to the feed lips, with no block to split off."},"front_to_back":{"label":"Front to back at the body top","kind":"length","measurements":[{"id":"gen-m3","value":2.528,"unit":"in","pm":0.035,"source":{"type":"derived","expr":"{magpul-pmag-30-gen-m3.front_to_back}"},"note":"Magpul's 30-round GEN M3's, by reference: the two are one generation for one magazine well (Magpul's sheets say of each 'Modified dimensions allow for wider compatibility with non Colt-spec platforms' in the same words, and its patent marking page lists the same utility patents against both: 8,069,601; 8,635,796; 8,991,086; 8,839,543; 7,908,780; 8,166,692; 7,958,660). Used to try what Magpul's 'Length, max' spans: this part's own patent's side elevation, scaled by 5.6 in as its upright height, has to give this."},{"id":"patent","value":2.496,"unit":"in","pm":0.045,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 57d9f77b9610 (US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi)","scaleRef":"scale from magpul-pmag-20-gen-m3.overall_height = 5.6 in (y-extent 2028 px → 362.1 px/in)","method":"median row width in y [-2.6, -0.7] (2.496–2.496) of the traced outline (tools/trace.py); the top section's front to back where it is straight and stands in the well, spine's rear face to front face (the median row)","via":"harvest"}},{"id":"photo","value":2.49,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 7322951944be (Magpul's own photo of MAG560's left side, gallery 02.1, black, on white, 1200 px)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the silhouette's 1032 px with the top section's edges stood upright (turned 0.2 degrees; its rear edge leans 0.3 and its front -0.7 in the photo): 184.2 px/in; x from the spine's rear face in the well (the photo mirrored), y from the feed lips' top (tools/trace.py, the `left-photo` spec)","method":"the silhouette's width on rows through the top section: 2.47 at y -1.0, 2.49 at -2.0, 2.50 at -2.6 (.cache/pmag20/feat.py); its outline lies on the patent's left elevation, IoU 0.987","via":"harvest"}}],"adopt":{"from":"patent","reason":"This part's own design patent's elevation scaled by its own published height; Magpul's photograph of the product scaled the same way reads the same (2.49), and the 30-round's, by reference, 0.03 more: inside its ±. It goes into a standard well (2.553 in with the spine's slot) with 0.06 in to spare."},"note":"The top section that stands in the well, from the spine's rear face to the front face."},"catch_notch_top":{"label":"Magazine catch notch (left side), its upper edge below the feed lips' top","kind":"length","measurements":[{"id":"photo","value":1.055,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 7322951944be (Magpul's own photo of MAG560's left side, gallery 02.1, black, on white, 1200 px)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the silhouette's 1032 px with the top section's edges stood upright (turned 0.2 degrees; its rear edge leans 0.3 and its front -0.7 in the photo): 184.2 px/in; x from the spine's rear face in the well (the photo mirrored), y from the feed lips' top (tools/trace.py, the `left-photo` spec)","method":"the catch's window is the rounded pocket at columns 701 to 791.5; its upper edge at row 291 (the dark line of the edge on a tile enlarged five times with its pixel grid, .cache/pmag20/tp_notch.png, +/- 1.5 px), which the placement puts 1.054 to 1.056 in under the lips' top; the ± is that pick, the silhouette's top and the height's own ± on an inch","via":"harvest"}},{"id":"patent","value":1.107,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 6ed4a10c5b72 (US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 3 left side elevation, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2071 px: 369.8 px/in; x from the spine's rear face in the well (the figure mirrored), y from the feed lips' top (tools/trace.py, the `left` spec)","method":"the rounded rectangle's upper line, the middle of its stroke at row 1110","via":"harvest"},"note":"This magazine's own design patent (the one its maker's marking page lists against it): a drawing, 0.05 in lower than the photograph."},{"id":"gen-m3","value":1.07,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{magpul-pmag-30-gen-m3.catch_notch_top}"},"note":"The 30-round GEN M3's own reading (its photograph), by reference: both hang on the one catch in the one well, under one generation's feed lips."}],"adopt":{"from":"photo","reason":"Magpul's photograph of the product itself; the 30-round's own reading is 0.015 in from it and the patent's drawing within the two readings' ±."},"note":"What seats it: the notch's upper edge hangs on the lower's catch (the `magwell` anchor). Read on this magazine's own photograph; its own design patent draws the window 0.05 in lower, as the 30-round's patent does against that magazine's photograph (1.12 for 1.07): the photograph of the product decides, and the 30-round's own reading, by reference, is 0.015 from this one. All are scaled by Magpul's 'Length, max' as the upright height."},"catch_notch_height":{"label":"Magazine catch notch (left side), its height","kind":"length","measurements":[{"id":"photo","value":0.244,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 7322951944be (Magpul's own photo of MAG560's left side, gallery 02.1, black, on white, 1200 px)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the silhouette's 1032 px with the top section's edges stood upright (turned 0.2 degrees; its rear edge leans 0.3 and its front -0.7 in the photo): 184.2 px/in; x from the spine's rear face in the well (the photo mirrored), y from the feed lips' top (tools/trace.py, the `left-photo` spec)","method":"the pocket's upper and lower edges, rows 291 and 336 (the dark lines of the two edges, +/- 1.5 px each): y -1.055 to -1.299","via":"harvest"}},{"id":"patent","value":0.252,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 6ed4a10c5b72 (US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 3 left side elevation, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2071 px: 369.8 px/in; x from the spine's rear face in the well (the figure mirrored), y from the feed lips' top (tools/trace.py, the `left` spec)","method":"the rounded rectangle's upper and lower lines, the middles of their strokes at rows 1110 and 1203: y -1.107 to -1.359","via":"harvest"}}],"adopt":{"from":"photo","reason":"Magpul's photograph of the product itself; the patent's drawing agrees within the two readings' ±, and is the lower's slot to the thousandth."},"note":"The window the catch comes into: as tall as the slot it comes through in a lower (std.ar15.mag_catch_slot_h, 0.252 in)."},"catch_notch_rear_x":{"label":"Magazine catch notch (left side), its rear end ahead of the spine's rear face","kind":"length","measurements":[{"id":"photo","value":0.483,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 7322951944be (Magpul's own photo of MAG560's left side, gallery 02.1, black, on white, 1200 px)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the silhouette's 1032 px with the top section's edges stood upright (turned 0.2 degrees; its rear edge leans 0.3 and its front -0.7 in the photo): 184.2 px/in; x from the spine's rear face in the well (the photo mirrored), y from the feed lips' top (tools/trace.py, the `left-photo` spec)","method":"the pocket's rear edge, column 791.5 (+/- 1.5 px); the ± is that, the spine's edge in the photo and the scale","via":"harvest"}},{"id":"patent","value":0.491,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 6ed4a10c5b72 (US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 3 left side elevation, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2071 px: 369.8 px/in; x from the spine's rear face in the well (the figure mirrored), y from the feed lips' top (tools/trace.py, the `left` spec)","method":"the rounded rectangle's rear line, the middle of its stroke at column 1672","via":"harvest"}}],"adopt":{"from":"photo","reason":"Magpul's photograph of the product itself; the patent's drawing agrees within the two readings' ±."}},"catch_notch_front_x":{"label":"Magazine catch notch (left side), its front end ahead of the spine's rear face","kind":"length","measurements":[{"id":"photo","value":0.974,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 7322951944be (Magpul's own photo of MAG560's left side, gallery 02.1, black, on white, 1200 px)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the silhouette's 1032 px with the top section's edges stood upright (turned 0.2 degrees; its rear edge leans 0.3 and its front -0.7 in the photo): 184.2 px/in; x from the spine's rear face in the well (the photo mirrored), y from the feed lips' top (tools/trace.py, the `left-photo` spec)","method":"the pocket's front edge, column 701 (+/- 1.5 px): the window 0.49 in long","via":"harvest"}},{"id":"patent","value":1.013,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 6ed4a10c5b72 (US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 3 left side elevation, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2071 px: 369.8 px/in; x from the spine's rear face in the well (the figure mirrored), y from the feed lips' top (tools/trace.py, the `left` spec)","method":"the rounded rectangle's front line, the middle of its stroke at column 1479: the rectangle 0.52 in long","via":"harvest"}}],"adopt":{"from":"photo","reason":"Magpul's photograph of the product itself; the patent's drawing reads 0.04 in further forward, as the 30-round's does against its photograph."}},"catch_block_proud":{"label":"The block under the catch notch (left side), standing out of the side","kind":"length","measurements":[{"id":"patent-front","value":0.057,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 b1e83c27171f (US D691,233 S (Magpul), FIG. 6 front elevation, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in","method":"rows 1172 to 1212: the block's outer line at column 1017.5, the side's at 996.5 (the middles of the strokes, .cache/pmag20/lines.py): 21 px; its top between rows 1164 and 1172 (1.37 in under the lips' top), its chamfer back to the side by row 1244; ± 2 px","via":"harvest"}},{"id":"patent-rear","value":0.054,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 b1e83c27171f (US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in","method":"rows 1172 to 1212: the block's outer line at column 1517.5, the side's at 1537.5: 20 px; ± 2 px","via":"harvest"}}],"adopt":{"from":"patent-front","reason":"The two elevations agree within a pixel; the front one is the figure the front outline is traced from."},"note":"As on the 30-round GEN M3 (its ledger's catch_block_proud has the whole account): this magazine's own patent draws a block under the catch's window, in profile on the right of its front elevation and the left of its rear one, in outline on the left elevation; Magpul's photo of the product has its outline under the window with a darker band along its lower end. NOT RECONCILED WITH THE WELL, here either: hung by its notch, the block is under the catch's slot in a lower's left wall, where a standard well is .898 wide (std.ar15.magwell_width), and a top section 0.902 wide as drawn with this block on it is 0.96. It is not built."},"catch_relief_proud":{"label":"The relief over the catch notch (left side), standing out of the side","kind":"length","measurements":[{"id":"patent-front","value":0.013,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 b1e83c27171f (US D691,233 S (Magpul), FIG. 6 front elevation, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in","method":"the traced outline's corner at 0.460 from the middle, 0.915 in under the lips, against the straight line through that side at 0.53 and 2.46 in under them (0.447 there); the other side has no such corner; ± 2 px","via":"harvest"}}],"note":"Over the catch's window this magazine's patent draws a four-sided outline as long as the block under it, from 0.75 to 1.11 in under the lips (its left elevation), and the front elevation's silhouette swells there on that side alone: a shallow boss or ramp over the window. Magpul's photo has its outline faintly. Not built (a thing at one place along the magazine, which a hull would carry down the whole left side into a well's wall); kept as read."},"catch_block_length":{"label":"The block under the catch notch, its length along the magazine (front to back)","kind":"length","measurements":[{"id":"photo","value":0.38,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 7322951944be (Magpul's own photo of MAG560's left side, gallery 02.1, black, on white, 1200 px)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the silhouette's 1032 px with the top section's edges stood upright (turned 0.2 degrees; its rear edge leans 0.3 and its front -0.7 in the photo): 184.2 px/in; x from the spine's rear face in the well (the photo mirrored), y from the feed lips' top (tools/trace.py, the `left-photo` spec)","method":"the dark lines of its two ends, columns 711 and 781 (+/- 1.5 px): x 0.539 to 0.919","via":"harvest"}},{"id":"patent","value":0.4,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 6ed4a10c5b72 (US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 3 left side elevation, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2071 px: 369.8 px/in; x from the spine's rear face in the well (the figure mirrored), y from the feed lips' top (tools/trace.py, the `left` spec)","method":"the lower rectangle's two side lines, columns 1502 and 1650: x 0.55 to 0.95","via":"harvest"}}],"adopt":{"from":"photo","reason":"Magpul's photograph of the product itself; the patent's drawing agrees within the two readings' ±."}},"catch_block_height":{"label":"The block under the catch notch, from the notch's lower edge down to where it is back in the side","kind":"length","measurements":[{"id":"patent-side","value":0.195,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 6ed4a10c5b72 (US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 3 left side elevation, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2071 px: 369.8 px/in; x from the spine's rear face in the well (the figure mirrored), y from the feed lips' top (tools/trace.py, the `left` spec)","method":"the lower rectangle, from the rounded rectangle's lower line (row 1203) to its own lower line (row 1275): 72 px","via":"harvest"}}]},"side_panel_depth":{"label":"The side panels' floors below the grip frame's ribs and bands","kind":"length","measurements":[{"id":"patent-front","value":0.023,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 b1e83c27171f (US D691,233 S (Magpul), FIG. 6 front elevation, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in","method":"rows 1820 to 2060 (the frame's one row of panels): the frame's silhouette at columns 656.5 and 1007.5, the panels' floor line at 664.5 and 998.5 (.cache/pmag20/lines.py): 8.0 and 9.0 px, centre to centre; ± 2 px for two lines 3 px thick","via":"harvest"}},{"id":"patent-rear","value":0.027,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 b1e83c27171f (US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in","method":"rows 1860 to 2140: the frame's silhouette at columns 1528 and 1877.5, the panels' floor line at 1538 and 1867.5: 10 px each side; ± 2 px","via":"harvest"}}],"adopt":{"from":"patent-rear","reason":"The two readings are one thing within their ± (0.004 in apart, as on the 30-round: 0.025 and 0.029). The model's floors are the plain sides' own plane carried down and its frame the traced front outline's, whose two levels come out 0.028 in apart on the left and 0.030 on the right (the outline rides the strokes a line's weight outside their middles): the rear elevation's figure is the one that says what is built, within its ±."},"note":"How far the frame stands out of each side, read where this magazine's own patent shows a floor in profile, as the 30-round's does: the front column's panel runs out to the front face and the rear one to the spine, so the front and rear elevations have their floors as a line inside the frame's silhouette, and that line runs on from the silhouette of the plain sides above the frame (FIG. 6: 665.5 and 998 above, 664.5 and 998.5 between the bands). The one closed panel and the one with the dot matrix show in no profile and are taken to the same floor. Under the band, at the dot matrix's height, the silhouette is the rib between the two lower panels and stands 0.013 to 0.018 in over that floor, less than the bands."},"side_panel_wall_run":{"label":"A side panel's wall, from its rim on the frame in to its floor's edge, as the side view has it","kind":"length","measurements":[{"id":"patent","value":0.027,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 6ed4a10c5b72 (US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 3 left side elevation, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2071 px: 369.8 px/in; x from the spine's rear face in the well (the figure mirrored), y from the feed lips' top (tools/trace.py, the `left` spec)","method":"the two lines round the one closed panel, its rim and its floor's edge: 9.5 px apart on its upper edge and 11.5 on its front edge (a tile of the sheet with its pixel grid, .cache/pmag20/t3_frame.png); ± 2 px","via":"harvest"}}],"note":"About as far across as the panel is deep: a wall near 45 degrees, as on the 30-round (0.026 in)."},"side_panel_corner_radius":{"label":"A side panel's corners, their radius at the middle of the wall","kind":"length","measurements":[{"id":"gen-m3","value":0.08,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{magpul-pmag-30-gen-m3.side_panel_corner_radius}"},"note":"The 30-round GEN M3's, read on Magpul's photograph of that magazine, by reference: the same moulded panels. This magazine's patent draws its closed panel's corners at about 0.06 in (a tile of FIG. 3, not measured closer), inside that reading's ±."}]},"dot_depth":{"label":"The dot matrix's squares, their depth","kind":"length","measurements":[{"id":"as-panels","value":0.016,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"0.6 * {.side_panel_depth}"}}],"note":"Sunk: on Magpul's photo of this magazine each square is dark along its upper edge, as the sunk panels' upper walls are (and as the block under the catch notch, which stands, is along its lower one); 'a paint pen dot matrix ... to allow easy marking', Magpul's sheet: places for paint. HOW DEEP IS ASSUMED: no view on file shows a square in profile. Six tenths of this magazine's own panels' depth, as the 30-round GEN M3's model has its dimples (that part's script: their walls' shadows on Magpul's photo of that magazine are that much weaker than the panels')."},"dot_size":{"label":"The dot matrix: a square across, wall to wall","kind":"length","measurements":[{"id":"patent","value":0.086,"unit":"in","pm":0.007,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 6ed4a10c5b72 (US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 3 left side elevation, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2071 px: 369.8 px/in","method":"the smallest rectangle round the white inside each of the sixty drawn squares, out by half the stroke: 31.1 to 33.1 px, 31.8 the middle value (.cache/pmag20/dots.py); the right elevation's sixty: 31.2 of 362.1 px/in, the same","via":"harvest"}},{"id":"gen-m3","value":0.068,"unit":"in","pm":0.008,"source":{"type":"derived","expr":"{magpul-pmag-30-gen-m3.dot_matrix_dimple}"},"note":"The 30-round GEN M3's, read on Magpul's photograph of that magazine: the same matrix (four blocks of three by five a side at a tenth of an inch; this one's pitch is 0.099 on its patent)."}],"adopt":{"from":"gen-m3","reason":"A photograph of the moulded squares against a drawing of them: the drawing's are drawn out to a heavy stroke, and this magazine's own photograph has the lands the smaller figure leaves. The drawing's figure stays."},"note":"Where each square is, is this magazine's own patent's (profiles.left and profiles.side, features `dots`); how big one is, is the 30-round's reading. The patent draws each square with a heavy stroke, the squares nearly touching (0.086 in to the stroke's middle at a pitch of 0.099, the white inside the stroke 0.0725); Magpul's photo of this magazine (184 px to the inch) has them apart by lands about a third of the pitch, as the 30-round's figure gives, and is too coarse to size one."},"dots_per_side":{"label":"The dot matrix's squares on each side","kind":"count","measurements":[{"id":"patent-left","value":60,"unit":"count","source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 6ed4a10c5b72 (US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 3 left side elevation, 300 dpi)","scaleRef":"a count","method":"the closed white areas inside the small drawn squares, labelled and counted (.cache/pmag20/dots.py): 60, each 652 to 673 px","via":"harvest"}},{"id":"patent-right","value":60,"unit":"count","source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 57d9f77b9610 (US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi)","scaleRef":"a count","method":"the same count on the right side elevation: 60, each 597 to 669 px","via":"harvest"}}],"adopt":{"from":"patent-left","reason":"The two sides agree."},"note":"Four groups, each three across and five down, on each side. Each side is drawn from its own elevation, and the two are each other's mirror within 0.006 in (the groups' rearmost squares 0.686 and 0.689 in ahead of the spine's rear face, their foremost 1.97 and 1.98)."},"bars_front":{"label":"The bars across the front strip","kind":"count","measurements":[{"id":"patent-front","value":10,"unit":"count","source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 b1e83c27171f (US D691,233 S (Magpul), FIG. 6 front elevation, 300 dpi)","scaleRef":"a count","method":"the pairs of lines down the strip's middle (columns 800 and 850, rows 1780 to 2410): five between the frame's upper band and its middle one, five between that and the floorplate","via":"harvest"}}],"note":"Two rows of five, one in each row of the grip frame."},"bars_spine":{"label":"The bars across the spine under the stop","kind":"count","measurements":[{"id":"patent-rear","value":10,"unit":"count","source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 b1e83c27171f (US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi)","scaleRef":"a count","method":"the pairs of lines down columns 1650 and 1760 (either side of the rib), rows 1880 to 2545: five beside the rib, five under the band","via":"harvest"}}],"note":"Two rows of five. In the upper row the long rib down the spine's middle stands over them, and from the side they are behind it."},"strip_bar_thickness":{"label":"A bar of the front strip or the spine, its thickness along the magazine","kind":"length","measurements":[{"id":"patent-front","value":0.034,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 b1e83c27171f (US D691,233 S (Magpul), FIG. 6 front elevation, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in","method":"a bar's two lines, the middles of their strokes: 12 to 13 px apart on all ten (12.5 the middle value); ± 2 px","via":"harvest"}},{"id":"patent-rear","value":0.033,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 b1e83c27171f (US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in","method":"the same on the spine's ten: 10 to 12.5 px (12 the middle value)","via":"harvest"}}],"adopt":{"from":"patent-front","reason":"The two elevations agree within a pixel; the front one has the more even lines."},"note":"The 30-round GEN M3's own read 0.034 in on its patent (its ledger): the same bars."},"front_strip_width":{"label":"The front strip: the flat of the grip frame's front face that the bars lie across","kind":"length","measurements":[{"id":"patent-front","value":0.437,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 b1e83c27171f (US D691,233 S (Magpul), FIG. 6 front elevation, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in","method":"the strip's two edge lines on rows 1820 to 2366, columns 752 and 912.5: 160.5 px; the bars themselves run from 756 to 908.5 (0.415 in); ± 2 px and the scale","via":"harvest"}}],"note":"The 30-round GEN M3's is 0.44 in on its own patent."},"spine_rib_width":{"label":"The long rib down the spine's middle (upper row), and the stop's gusset over it","kind":"length","measurements":[{"id":"patent-rear","value":0.148,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 b1e83c27171f (US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in","method":"the rib's two sides on rows 1890 to 2010, columns 1675.5 and 1730: 54.5 px (inside them the two lines of its face's edges, 1682.5 and 1723); ± 2 px and the scale","via":"harvest"}}],"note":"The 30-round GEN M3's is 0.151 in on its own patent."},"front_bar_proud":{"label":"The front strip's bars, how far they stand out of the strip","kind":"length","measurements":[{"id":"patent","value":0.014,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 6ed4a10c5b72 (US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 3 left side elevation, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2071 px: 369.8 px/in","method":"the first bar of the upper row on rows 1838 and 1844: its outer line at column 881.5, the front edge's own at 886.5 (the middles of the ink's runs): 5 px; ± 2 px","via":"harvest"}},{"id":"gen-m3","value":0.017,"unit":"in","pm":0.004,"source":{"type":"derived","expr":"{magpul-pmag-30-gen-m3.front_bar_proud}"},"note":"The 30-round GEN M3's own, by reference: one generation's front strip."}],"adopt":{"from":"patent","reason":"This magazine's own drawing; the 30-round's reading is 0.003 in more, inside both ±."},"note":"Read on this magazine's own patent, where a bar shows in the side elevation as a small square across the front edge's line; the 30-round's, on Magpul's photograph of that magazine, is within a line's weight of it."},"spine_bar_proud":{"label":"The spine's bars, how far they stand out of the spine","kind":"length","measurements":[{"id":"gen-m3","value":0.022,"unit":"in","pm":0.006,"source":{"type":"derived","expr":"{magpul-pmag-30-gen-m3.spine_bar_proud}"}}],"note":"Not read on this magazine: its side elevations have the spine's lower row as a ripple of 0.01 to 0.025 in in the traced outline and its upper row as the rib's straight face, and no bar's own outline there. The 30-round GEN M3's, by reference (the same spine under the stop: its rib is 0.151 in wide for this one's 0.148, its bars as thick). The rib stands as far as the bars, as there."},"front_corner_depth":{"label":"The grip frame's front corners: how far behind the front face a side begins to turn in","kind":"length","measurements":[{"id":"patent-side","value":0.117,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 57d9f77b9610 (US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2028 px: 362.1 px/in; x from the spine's rear face in the well, y from the feed lips' top (the side trace's own placement of the figure)","method":"across the upper row on rows 1880 to 2080: the thin line inside the front panel 41.5 to 43 px behind the front edge's own line (42.2 the mean of five rows, the middles of the ink's runs, .cache/pmag20/meas6.sh); across the lower row 44.5 and 46 px on two rows; ± 3 px","via":"harvest"}},{"id":"gen-m3","value":0.115,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{magpul-pmag-30-gen-m3.front_corner_depth}"},"note":"The 30-round GEN M3's own, on its own patent, by reference."}],"adopt":{"from":"patent-side","reason":"This magazine's own drawing; the 30-round's is 0.002 in from it."},"note":"With front_strip_width, the round of the frame's front corners: a side runs forward flat to this far behind the front strip and then turns in to the strip's edge. No view has the turn in section; it is drawn as a quarter of an ellipse between the two, as the 30-round's is (ASSUMED: the front elevation has three lines down it, at 0.354, 0.390 and 0.422 in from the middle, where the 30-round's patent has its three at 0.358, 0.397 and 0.426)."},"rear_shoulder_width":{"label":"The grip frame's rear: the width over the two shoulders beside the spine, where the rounds into the sides begin","kind":"length","measurements":[{"id":"patent-rear","value":0.545,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 b1e83c27171f (US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in","method":"the strongest line outside the spine's on each side, columns 1602.5 and 1802.75 on rows 1920 to 2100 (the spine's own edges are at 1622.5 and 1782); ± 2 px each","via":"harvest"}},{"id":"gen-m3","value":0.554,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{magpul-pmag-30-gen-m3.rear_shoulder_width}"},"note":"The 30-round GEN M3's own, on its own patent, by reference."}],"adopt":{"from":"patent-rear","reason":"This magazine's own drawing; the 30-round's is 0.009 in more, inside both ±."}},"spine_strip_proud":{"label":"The spine's strip in the grip frame: how far it stands behind the shoulder beside it","kind":"length","measurements":[{"id":"patent-side","value":0.072,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 57d9f77b9610 (US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2028 px: 362.1 px/in; x from the spine's rear face in the well, y from the feed lips' top (the side trace's own placement of the figure)","method":"on rows 1980, 2030 and 2080 the first line ahead of the outline's rear edge is 33.3 to 34.1 px from it (0.094 in); the edge there is the long rib's face, which stands a bar's height behind the strip (spine_bar_proud, 0.022 in): 0.072 from the strip; ± 3 px","via":"harvest"}},{"id":"gen-m3","value":0.07,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{magpul-pmag-30-gen-m3.spine_strip_proud}"},"note":"The 30-round GEN M3's own, on its own patent, by reference."}],"adopt":{"from":"patent-side","reason":"This magazine's own drawing; the 30-round's is 0.002 in from it."},"note":"Between the bands the rear panel runs round the rear corner onto a shoulder, and the spine's strip stands behind it by this."},"rear_corner_depth":{"label":"The grip frame's rear corners: from the shoulder beside the spine to where a side begins to turn in","kind":"length","measurements":[{"id":"patent-side","value":0.124,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 57d9f77b9610 (US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2028 px: 362.1 px/in; x from the spine's rear face in the well, y from the feed lips' top (the side trace's own placement of the figure)","method":"the same three rows: the third line ahead of the rear edge at 78.8 to 79.6 px (0.218 in; 0.196 from the strip), less the shoulder's 0.072; in the lower row, where the edge is the strip's own teeth, the one line ahead of it is 73 to 74 px off (0.203 in) on rows 2300, 2360 and 2420; ± 4 px","via":"harvest"}},{"id":"gen-m3","value":0.12,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{magpul-pmag-30-gen-m3.rear_corner_depth}"},"note":"The 30-round GEN M3's own, on its own patent, by reference."}],"adopt":{"from":"patent-side","reason":"This magazine's own drawing; the 30-round's is 0.004 in less, inside both ±."},"note":"With rear_shoulder_width, the round of the frame's rear corners, drawn as a quarter of an ellipse (ASSUMED, as the front's)."},"spine_width":{"label":"The spine (the rib down the rear that runs in a well's slot), its width","kind":"length","measurements":[{"id":"patent-rear","value":0.438,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 b1e83c27171f (US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in","method":"the spine's two side lines on rows 1500 to 1740, columns 1621.5 and 1782.5 (.cache/pmag20/lines.py): 161 px; outside each a thinner line 14 px off (the round at its foot); ± 2 px and the scale","via":"harvest"}}],"note":"A standard well's slot for it is .470 wide (std.ar15.magwell_spine_slot_width)."},"spine_depth":{"label":"The spine, how far it stands behind the body's rear face","kind":"length","measurements":[{"id":"patent","value":0.139,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 57d9f77b9610 (US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2028 px: 362.1 px/in; x from the spine's rear face in the well, y from the feed lips' top","method":"on rows 940 to 1740 the outline's rear line (the spine's rear face) at column 685.5 to 686.5 and the heavy line of the body's rear face at 735.5 to 736.5 (.cache/pmag20/lines.py): 50 px; two thinner lines between them (706.5, 722) are edges on the spine's side; ± 2 px and the scale","via":"harvest"}}],"note":"A standard well's slot for it is .155 deep (std.ar15.magwell_length less magwell_box_length). The body ahead of it is then 2.36 in, in a box of 2.398."},"stop_behind_spine":{"label":"The over-travel stop's tip, behind the spine's rear face","kind":"length","measurements":[{"id":"patent","value":0.061,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 57d9f77b9610 (US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi)","scaleRef":"scale from magpul-pmag-20-gen-m3.overall_height = 5.6 in (y-extent 2028 px → 362.1 px/in)","method":"−x_min of the traced outline (tools/trace.py); the outline's rearmost point, the tip of the over-travel stop on the spine, behind the spine's rear face in the well (the frame's x = 0)","via":"harvest"}}]},"depth_overall":{"label":"Front to back over everything, the stop's tip to the floorplate's front","kind":"length","measurements":[{"id":"patent","value":2.993,"unit":"in","pm":0.054,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 57d9f77b9610 (US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi)","scaleRef":"scale from magpul-pmag-20-gen-m3.overall_height = 5.6 in (y-extent 2028 px → 362.1 px/in)","method":"width of the traced outline (tools/trace.py); the whole outline front to back: from the stop's tip to the floorplate's front","via":"harvest"}}]},"width":{"label":"Width (side to side) of the top section, where it stands in the well","kind":"length","measurements":[{"id":"patent","value":0.902,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 b1e83c27171f (US D691,233 S (Magpul), FIG. 6 front elevation, 300 dpi)","scaleRef":"scale from magpul-pmag-20-gen-m3.overall_height = 5.6 in (y-extent 2059 px → 367.7 px/in)","method":"median row width in y [-2.2, -0.7] (0.892–0.955) of the traced outline (tools/trace.py); the top section's width where it stands in the well, clear of the block under the catch notch (the median row)","via":"harvest"}},{"id":"patent-rear","value":0.9,"unit":"in","pm":0.018,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 b1e83c27171f (US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in","method":"median row width in y [-2.2, -0.7] (0.891–0.953) of the rear elevation's traced outline (tools/trace.py, the `rear` spec)","via":"harvest"}},{"id":"trex","value":0.87,"unit":"in","pm":0.005,"stated":"Dimensions (LxWxH): 5.7\" x 2.6\" x 0.87\"","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, Magpul AR/M4 PMAG: Technical Specifications, the PMAG 20 column","url":"https://www.trex-arms.com/store/magpul-ar-m4-pmag-336599","retrieved":"2026-10-13","via":"harvest"},"note":"The third of a seller's three figures, the same for the 20, the 30 and the 40; what it runs between isn't said."}],"adopt":{"from":"patent","reason":"The model is this part's own patent's elevations scaled by its published height, and the two elevations agree. The seller's figure is 0.03 in less and stays: nothing on file says which is the body's own width."},"note":"Magpul gives none. This magazine's own patent's front and rear elevations, each scaled by the height, agree; the one seller's figure is 0.03 in less, and is what a body that goes into a .898 in well with room would be. The model is the patent's (0.004 in over the well's own width: a line's weight of the drawing, or the height's ±)."},"frame_width":{"label":"Width of the gripping section, over its ribs and bands","kind":"length","measurements":[{"id":"patent","value":0.96,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 b1e83c27171f (US D691,233 S (Magpul), FIG. 6 front elevation, 300 dpi)","scaleRef":"scale from magpul-pmag-20-gen-m3.overall_height = 5.6 in (y-extent 2059 px → 367.7 px/in)","method":"median row width in y [-4.4, -3.2] (0.936–0.968) of the traced outline (tools/trace.py); the gripping section's width over its ribs and bands (the median row)","via":"harvest"}}]},"floorplate_width":{"label":"Width of the floorplate, its widest","kind":"length","measurements":[{"id":"patent","value":1.104,"unit":"in","pm":0.021,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 b1e83c27171f (US D691,233 S (Magpul), FIG. 6 front elevation, 300 dpi)","scaleRef":"scale from magpul-pmag-20-gen-m3.overall_height = 5.6 in (y-extent 2059 px → 367.7 px/in)","method":"width in y [-5.6, -4.9] of the traced outline (tools/trace.py); the floorplate, its widest","via":"harvest"}}]},"hang_below_magwell":{"label":"Hang below the magwell when seated","kind":"length","measurements":[{"id":"seated","value":2.912,"unit":"in","pm":0.12,"source":{"type":"derived","expr":"{bad-workhorse-lower.magwell_bottom_center_y} - ({std.ar15.mag_catch_slot_bottom_y} + {std.ar15.mag_catch_slot_h} + {.catch_notch_top} - {.overall_height})"}},{"id":"photo","value":2.8,"unit":"in","pm":0.11,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 aab5e4eac474 (Magpul's gallery 04.1: a whole rifle from its right side, square on, a black PMAG 20 seated in it; 1200 x 1200)","scaleRef":"the two receiver pins, 175 px apart (their middles at columns 384 and 559 on row 606.5, picked on a tile enlarged five times with its pixel grid, .cache/pmag20/seated5.png): std.ar15.pin_spacing = 6.375 in gives 27.45 px/in","method":"the well's mouth at the middle of the well, row 664 (its rear end at row 669, its front at 659), down to the magazine's lowest point, its rear lower corner, row 741: 77 px; ± 1.5 px at each end and the pins' picks. The lower is not one on file: its mouth is its own","via":"harvest"}}],"adopt":{"from":"seated","reason":"What the model does in the lower whose mouth is measured; Magpul's picture of one seated in another lower reads 0.11 in less, inside the two ±."},"note":"From the well's mouth at its middle down to the floorplate's lowest point, hung by its notch on the catch's upper face (the Army drawing's slot). The one lower on file whose mouth is measured is the Workhorse (its photo: bad-workhorse-lower.magwell_bottom_center_y, which carries no ±; the mouth rises 5.5 degrees toward the front, so the hang is more at the front of the well and less at its rear). A check on the seat, not what seats it. Magpul's own small picture of a 20 seated in a rifle is the second reading: a lower of no maker named, 27 px to the inch. In it the floorplate's lowest point is 4.90 in under the line of the two pins (134.5 px), where this seat puts it 4.98: 0.08 in, two of that picture's pixels."},"weight":{"label":"Weight, empty","kind":"mass","measurements":[{"id":"magpul","value":4,"unit":"oz","pm":0.5,"stated":"Weight 4 oz.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, PMAG 20 AR/M4 GEN M3 (MAG560), Technical Specifications","url":"https://magpul.com/pmag-20-ar-m4-gen-m3.html","retrieved":"2026-10-13","via":"harvest"}},{"id":"trex","value":4.1,"unit":"oz","pm":0.05,"stated":"Weight Unloaded: 4.1 oz (117g)","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, Magpul AR/M4 PMAG: Technical Specifications, the PMAG 20 column","url":"https://www.trex-arms.com/store/magpul-ar-m4-pmag-336599","retrieved":"2026-10-13","via":"harvest"},"note":"A seller's own table (its PMAG 30 column has 5.1 oz for Magpul's 5 oz)."}],"adopt":{"from":"magpul","reason":"The maker's own figure; the seller's 4.1 oz is inside the half ounce a whole-ounce figure covers."},"note":"Magpul's page gives a whole ounce; the one seller's table that weighs the three sizes (20, 30, 40) has it a tenth more, inside what a whole ounce covers."},"weight_loaded":{"label":"Weight, loaded with 20 rounds (a seller's figure)","kind":"mass","measurements":[{"id":"trex","value":12.5,"unit":"oz","pm":0.05,"stated":"Weight Loaded: 12.5 oz (355g)","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, Magpul AR/M4 PMAG: Technical Specifications, the PMAG 20 column","url":"https://www.trex-arms.com/store/magpul-ar-m4-pmag-336599","retrieved":"2026-10-13","via":"harvest"},"note":"Which cartridge isn't said."}]},"round_weight":{"label":"One round's share of the loaded weight","kind":"mass","measurements":[{"id":"trex","value":0.425,"unit":"oz","pm":0.025,"source":{"type":"derived","expr":"({.weight_loaded} - {.weight}) / {.capacity}"}}],"note":"What the loaded weight is worked out from in a build: the one seller's loaded figure (which cartridge isn't said) less Magpul's empty one, over its 20 rounds. By the seller's own pair (12.5 and 4.1 oz) it is 0.42; Magpul's own figures for its 60-round drum come to 0.425."},"stated_length":{"label":"Length as the manufacturer states it (reference points undefined)","kind":"length","measurements":[{"id":"magpul","value":5.6,"unit":"in","pm":0.05,"stated":"Length, max 5.6 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, PMAG 20 AR/M4 GEN M3 (MAG560), Technical Specifications","url":"https://magpul.com/pmag-20-ar-m4-gen-m3.html","retrieved":"2026-10-13","via":"harvest"}},{"id":"trex","value":5.7,"unit":"in","pm":0.05,"stated":"Dimensions (LxWxH): 5.7\" x 2.6\" x 0.87\"","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, Magpul AR/M4 PMAG: Technical Specifications, the PMAG 20 column","url":"https://www.trex-arms.com/store/magpul-ar-m4-pmag-336599","retrieved":"2026-10-13","via":"harvest"},"note":"The first of a seller's three figures; what L, W and H run between isn't said (its PMAG 30 column has 7.5 in, Magpul's own figure for that one)."}],"adopt":{"from":"magpul","reason":"The maker's own figure."},"note":"Neither page says what it runs between. Magpul's is taken as the upright height (overall_height); the seller's tenth more is about what the same magazine is along the lean of its lower half, or over a dust cover: not settled, and kept."},"stated_depth":{"label":"Front to back as a seller states it (reference points undefined)","kind":"length","measurements":[{"id":"trex","value":2.6,"unit":"in","pm":0.05,"stated":"Dimensions (LxWxH): 5.7\" x 2.6\" x 0.87\"","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, Magpul AR/M4 PMAG: Technical Specifications, the PMAG 20 column","url":"https://www.trex-arms.com/store/magpul-ar-m4-pmag-336599","retrieved":"2026-10-13","via":"harvest"}}],"note":"The second of T.REX ARMS' three figures, the same for the 20, the 30 and the 40: more than the top section's front to back (2.50 in by this part's patent) and what that is with the stop on its spine (2.56); the whole outline over the floorplate's lean is 2.99 (depth_overall). A check on the outline, not a dimension the model is built from."},"stated_width":{"label":"Width (side to side) as a seller states it (reference points undefined)","kind":"length","measurements":[{"id":"trex","value":0.87,"unit":"in","pm":0.005,"stated":"Dimensions (LxWxH): 5.7\" x 2.6\" x 0.87\"","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, Magpul AR/M4 PMAG: Technical Specifications, the PMAG 20 column","url":"https://www.trex-arms.com/store/magpul-ar-m4-pmag-336599","retrieved":"2026-10-13","via":"harvest"}}],"note":"The third of T.REX ARMS' three figures, the same for the 20, the 30 and the 40: the body where it stands in the well, by its size (a standard well is .898 wide inside). Magpul states no width."},"capacity":{"label":"Capacity","kind":"count","measurements":[{"id":"magpul","value":20,"unit":"count","stated":"Capacity 20 rounds","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, PMAG 20 AR/M4 GEN M3 (MAG560), Technical Specifications","url":"https://magpul.com/pmag-20-ar-m4-gen-m3.html","retrieved":"2026-10-13","via":"harvest"}}]},"nose_taper_length":{"label":"The body above the grip frame: how far behind the front face its sides begin to lean in","kind":"length","measurements":[{"id":"gen-m3","value":0.602,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{magpul-pmag-30-gen-m3.nose_taper_length}"},"note":"The 30-round GEN M3's, by reference (the same moulded top section, where both stand in a well). This magazine's own drawing bears it out: US D691,233 FIG. 2 (57d9f77b9610, 362.1 px/in) has the line where the lean begins at column 1375 to 1376.5 on rows 1010 to 1302 (between the two ribs) and the front edge's line at 1589 to 1590: 214 px, 0.591 in, ± 3 px (0.008): inside the two readings' ±. The line bows forward toward its ends (0.582 in at row 800, 0.567 at row 1519): drawn straight."}],"note":"The upper body narrows toward its front face: each side leans in from this far back to nose_shoulder_width, then rounds into a front face nose_front_width wide (nose_round_depth). The two guide ribs (guide_rib_*) and the tab on the frame's upper edge (frame_tab_*) are what the lean leaves at the side's own width. Detail pass, 2026-10-13."},"nose_round_depth":{"label":"The body above the grip frame: how far behind the front face the lean ends and the round into the front begins","kind":"length","measurements":[{"id":"gen-m3","value":0.068,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{magpul-pmag-30-gen-m3.nose_round_depth}"},"note":"The 30-round GEN M3's, by reference (the same moulded top section, where both stand in a well). This magazine's own drawing bears it out: FIG. 2 (57d9f77b9610) has the thin line at column 1565.5 on eleven rows from 849 to 1650 and the front edge's at 1589 to 1590: 24 px, 0.066 in, ± 2 px."}]},"nose_shoulder_width":{"label":"The body above the grip frame: its width where the lean ends","kind":"length","measurements":[{"id":"gen-m3","value":0.7,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{magpul-pmag-30-gen-m3.nose_shoulder_width}"},"note":"The 30-round GEN M3's, by reference (the same moulded top section, where both stand in a well). This magazine's own drawing bears it out: FIG. 6 (b1e83c27171f, 367.7 px/in) has the pair of lines at columns 704 and 959.5 on rows 1080 to 1330 (between the ribs): 255.5 px, 0.695 in, ± 3 px (0.008)."}]},"nose_front_width":{"label":"The body above the grip frame: the flat of its front face","kind":"length","measurements":[{"id":"gen-m3","value":0.526,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{magpul-pmag-30-gen-m3.nose_front_width}"},"note":"The 30-round GEN M3's, by reference (the same moulded top section, where both stand in a well). This magazine's own drawing bears it out: FIG. 6 (b1e83c27171f) has the inner pair of lines at columns 736 and 928.5 on the same rows: 192.5 px, 0.524 in, ± 3 px. (The silhouette there, the plain sides, is at 666.25 and 997: 0.900 in across the lines' middles.)"}]},"guide_rib_top_angle":{"label":"The upper guide rib on the upper body's front: how steeply its upper face rises as it goes in from the side","kind":"angle","measurements":[{"id":"gen-m3","value":29,"unit":"deg","pm":3,"source":{"type":"derived","expr":"{magpul-pmag-30-gen-m3.guide_rib_top_angle}"},"note":"The 30-round GEN M3's, by reference (the same moulded top section, where both stand in a well). This magazine's own drawing bears it out: FIG. 6 (b1e83c27171f) has the upper rib's upper face on rows 839, 833, 827.5, 822, 817, 811 at columns 680 to 730 (10 apart) on one side, 29.2 degrees, and 844, 836.5, 831, 825, 820, 814.5 at columns 990 to 940 on the other, 30.5 degrees; ± 2 degrees."}],"note":"Each rib keeps the side's own width to the front face where the body leans in round it: a flat face flush with the side and faces that slope toward the middle, so that from the side it shows as a wedge growing toward the front. The upper rib's lower face is level (FIG. 6: row 890.5 on every column from 680 to 730); the lower rib's two faces both slope (guide_rib_lower_angle)."},"guide_rib_upper_top":{"label":"The upper guide rib: its flat face's upper edge, below the feed lips' top","kind":"length","measurements":[{"id":"patent-side","value":0.48,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 57d9f77b9610 (US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2028 px: 362.1 px/in; x from the spine's rear face in the well (column 685.5), y from the feed lips' top (row 722.7): the side trace's own placement of the figure","method":"down columns 1420 to 1560 (five of them): the solid line at row 896.5 (896 to 898.5); the wedge's line over it runs from row 898.5 at column 1420 to 877.5 at column 1580 (0.052 in over the flat at the front); ± 3 px","via":"harvest"},"note":"This magazine's own design patent (it draws MAG560)."}]},"guide_rib_upper_height":{"label":"The upper guide rib: its flat face, from its upper edge to its lower","kind":"length","measurements":[{"id":"patent-side","value":0.133,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 57d9f77b9610 (US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2028 px: 362.1 px/in; x from the spine's rear face in the well (column 685.5), y from the feed lips' top (row 722.7): the side trace's own placement of the figure","method":"down the same columns: the solid lines at rows 896.5 and 944.5 (944.5 to 945): 48 px; a broken line runs 7.5 px inside each (904, 952); ± 3 px","via":"harvest"},"note":"This magazine's own design patent (it draws MAG560)."}]},"guide_rib_lower_top":{"label":"The lower guide rib: its flat face's upper edge, below the feed lips' top","kind":"length","measurements":[{"id":"patent-side","value":1.996,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 57d9f77b9610 (US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2028 px: 362.1 px/in; x from the spine's rear face in the well (column 685.5), y from the feed lips' top (row 722.7): the side trace's own placement of the figure","method":"down columns 1420 to 1560: the solid line at row 1445.5 (1445.5 to 1446.5); the wedge's line over it runs from 1442.5 at column 1420 to 1428 at column 1580; ± 3 px","via":"harvest"},"note":"This magazine's own design patent (it draws MAG560)."}]},"guide_rib_lower_height":{"label":"The lower guide rib: its flat face, from its upper edge to its lower","kind":"length","measurements":[{"id":"patent-side","value":0.102,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 57d9f77b9610 (US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2028 px: 362.1 px/in; x from the spine's rear face in the well (column 685.5), y from the feed lips' top (row 722.7): the side trace's own placement of the figure","method":"down the same columns: the solid lines at rows 1445.5 and 1482.5 (1482.5 to 1484): 37 px; under it a second wedge's line runs from 1484 at column 1420 to 1500 at column 1580; ± 3 px","via":"harvest"},"note":"This magazine's own design patent (it draws MAG560)."}]},"guide_rib_lower_angle":{"label":"The lower guide rib: how steeply its upper face rises and its lower face falls as they go in from the side","kind":"angle","measurements":[{"id":"patent-front","value":19,"unit":"deg","pm":3,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 b1e83c27171f (US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 6 front elevation, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px: 367.7 px/in; across from the figure's own middle column (831.9: the mean of three pairs of lines, 831.6, 831.75 and 832.25)","method":"the lower rib on one side, columns 680 to 730: its upper face on rows 1391.5, 1387.5, 1382.5, 1380.5, 1376.5, 1374.5 (18.8 degrees) and its lower on 1438.5, 1440.5, 1444, 1447.5, 1451, 1455 (18.3); on the other side, columns 990 to 950: 1394, 1389.5, 1386.5, 1382.5, 1379 (20.6) and 980 to 940: 1438.5, 1441.5, 1445.5, 1448.5, 1452 (18.7); one figure for both faces; ± covers the four","via":"harvest"},"note":"This magazine's own design patent (it draws MAG560)."}],"note":"Unlike the upper rib (and unlike the 30-round's two, as that part's ledger has them) the lower rib is a wedge both ways: FIG. 2 has a wedge's line above its flat face and another below, and FIG. 6 both faces sloping."},"frame_tab_top":{"label":"The tab on the grip frame's upper edge: its top, below the feed lips' top","kind":"length","measurements":[{"id":"patent-side","value":2.312,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 57d9f77b9610 (US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2028 px: 362.1 px/in; x from the spine's rear face in the well (column 685.5), y from the feed lips' top (row 722.7): the side trace's own placement of the figure","method":"down columns 1450, 1480 and 1500: the heavy line of its top at rows 1562.5, 1560 and 1558 to 1563 (a second line 9 px under it); 1560 taken; ± 3 px","via":"harvest"},"note":"This magazine's own design patent (it draws MAG560)."}],"note":"The tab stands up from the frame's upper edge near the front, about half an inch high. Like the ribs it is a piece of the side at the side's own width where the side leans in: FIG. 6 (b1e83c27171f, rows 1560 to 1640) has its face on the silhouette at columns 665 and 998.5, 0.4535 in from the middle, as the plain side over it is (0.450), with its inner edges at 0.419 and 0.3875 (the 30-round's: 0.425 and 0.394)."},"frame_tab_front":{"label":"The tab on the grip frame's upper edge: its front side at its top, behind the upper body's front face","kind":"length","measurements":[{"id":"patent-side","value":0.2,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 57d9f77b9610 (US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2028 px: 362.1 px/in; x from the spine's rear face in the well (column 685.5), y from the feed lips' top (row 722.7): the side trace's own placement of the figure","method":"its front side's heavy line at columns 1519.5, 1523.5 and 1526 on rows 1600, 1650 and 1700 (a thinner line 9 px inside it), carried up to its top at row 1560: 1517; the front edge's line at 1589.5: 72.5 px; ± 3 px","via":"harvest"},"note":"This magazine's own design patent (it draws MAG560)."}]},"frame_tab_length":{"label":"The tab on the grip frame's upper edge: front to back","kind":"length","measurements":[{"id":"patent-side","value":0.226,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 57d9f77b9610 (US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2028 px: 362.1 px/in; x from the spine's rear face in the well (column 685.5), y from the feed lips' top (row 722.7): the side trace's own placement of the figure","method":"between the heavy lines of its two sides on rows 1600, 1650 and 1700: 1438 to 1519.5, 1441.5 to 1523.5, 1444 to 1526: 81.5 to 82 px; ± 3 px","via":"harvest"},"note":"This magazine's own design patent (it draws MAG560)."}]},"frame_tab_lean":{"label":"The tab on the grip frame's upper edge: how far its sides lean forward as they go down","kind":"angle","measurements":[{"id":"patent-side","value":3.6,"unit":"deg","pm":1,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 57d9f77b9610 (US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2028 px: 362.1 px/in; x from the spine's rear face in the well (column 685.5), y from the feed lips' top (row 722.7): the side trace's own placement of the figure","method":"its rear side's line at columns 1438, 1441.5, 1444 and its front side's at 1519.5, 1523.5, 1526 on rows 1600, 1650, 1700: 6 and 6.5 px forward over 100 rows; ± 1 degree is a pixel at either end","via":"harvest"},"note":"This magazine's own design patent (it draws MAG560)."}]},"frame_tab_corner_radius":{"label":"The tab on the grip frame's upper edge, the round of its two upper corners","kind":"length","measurements":[{"id":"gen-m3","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{magpul-pmag-30-gen-m3.frame_tab_corner_radius}"},"note":"The 30-round GEN M3's, read on Magpul's photograph of that magazine, by reference. NOT read on this magazine: its patent's FIG. 2 draws the tab's upper corners round (the top's line and each side's meet over about 10 px, 0.03 in, by eye on a tile), and Magpul's photo of the 20 is too coarse (184 px to the inch) to say more."}]},"upper_rear_corner_radius":{"label":"The body above the grip frame: the round of its rear corners, from the body's rear face beside the spine into the side","kind":"length","measurements":[{"id":"gen-m3","value":0.057,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{magpul-pmag-30-gen-m3.upper_rear_corner_radius}"},"note":"The 30-round GEN M3's, by reference (the same moulded top section, where both stand in a well). This magazine's own drawing bears it out: FIG. 7 (the rear elevation on sheet b1e83c27171f, 368.2 px/in, its middle column 1703) has a line at columns 1559.5 and 1846.5 inside the silhouette's 1537.5 and 1868.5 on rows 1000 to 1330: 22 px, 0.060 in; FIG. 2 (57d9f77b9610) has the body's rear face at column 736.5 (spine_depth) and the next line at 754.5: 18 px, 0.050 in; ± 3 px each."}]},"spine_groove_x":{"label":"The slim groove near the spine: its middle, ahead of the spine's rear face","kind":"length","measurements":[{"id":"patent-side","value":0.415,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 57d9f77b9610 (US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2028 px: 362.1 px/in; x from the spine's rear face in the well (column 685.5), y from the feed lips' top (row 722.7): the side trace's own placement of the figure","method":"its two heavy lines at columns 827 (825.5 to 829.5) and 844.5 (843 to 845.5) on eighteen rows from 800 to 1120, a thin line at 840.5 between them: their middle at 835.75; ± 3 px","via":"harvest"},"note":"This magazine's own design patent (it draws MAG560)."}],"note":"A slim groove with round ends runs down each side of the upper body near the spine, from under the top to about the height of the catch's window. Read on the right side elevation; Magpul's photo of the left side (7322951944be) shows the same groove there (seen, not measured: the photo is 184 px to the inch and the groove 9 px wide), and the left's is drawn as the right's mirrored. HOW DEEP IS ASSUMED: it breaks no outline in any view on file. Drawn with walls leaning as far across as it is deep, to a floor a quarter of its width (0.018 in). Detail pass, 2026-10-13."},"spine_groove_width":{"label":"The slim groove near the spine: across, between its two edges","kind":"length","measurements":[{"id":"patent-side","value":0.048,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 57d9f77b9610 (US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2028 px: 362.1 px/in; x from the spine's rear face in the well (column 685.5), y from the feed lips' top (row 722.7): the side trace's own placement of the figure","method":"between the middles of its two heavy lines, columns 827 and 844.5, on the same rows: 17.5 px; each line is 4 to 5 px heavy, which the ± covers","via":"harvest"},"note":"This magazine's own design patent (it draws MAG560)."}]},"spine_groove_top":{"label":"The slim groove near the spine: its upper end, below the feed lips' top","kind":"length","measurements":[{"id":"patent-side","value":0.176,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 57d9f77b9610 (US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2028 px: 362.1 px/in; x from the spine's rear face in the well (column 685.5), y from the feed lips' top (row 722.7): the side trace's own placement of the figure","method":"down columns 830 and 835: the top of its round end at rows 786.5 and 787 (down column 827 its line begins at 786.5); ± 3 px","via":"harvest"},"note":"This magazine's own design patent (it draws MAG560)."}]},"spine_groove_length":{"label":"The slim groove near the spine: from its upper end to its lower","kind":"length","measurements":[{"id":"patent-side","value":0.938,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 57d9f77b9610 (US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2028 px: 362.1 px/in; x from the spine's rear face in the well (column 685.5), y from the feed lips' top (row 722.7): the side trace's own placement of the figure","method":"down columns 835 and 840: its lower round end at rows 1126 and 1125.5, its upper at 786.5: 339.5 px; ± 3 px","via":"harvest"},"note":"This magazine's own design patent (it draws MAG560)."}]},"stop_flat_half_width":{"label":"The over-travel stop on the spine: half the width of its rear face where it is flat, before its corners round off","kind":"length","measurements":[{"id":"patent-top","value":0.287,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 fe9c4793263a (US D691,233 S (Magpul), sheet 4: FIG. 4 top plan and FIG. 5 bottom plan, 300 dpi)","scaleRef":"the sheet's own scale: its two plans' widest rows (FIG. 4 row 1630, 381 px; FIG. 5 row 1763, 384 px: the floorplate) over the front elevation's floorplate width (profiles.front, 2 x 0.552 in): 346.5 px/in, ± 1% (FIG. 4's length, rows 1194 to 2219 over the side outline's 2.994 in, reads 1.2% smaller); across from each figure's own middle (FIG. 4 column 853.4, FIG. 5 column 1667.5)","method":"FIG. 4: the rear edge's line on row 1195, one pixel ahead of the edge, from column 756 to 955 (99.5 px each side of the middle); ± 4 px, the line being drawn in dashes there","via":"harvest"},"note":"This magazine's own design patent. Primary Arms' and Magpul's views of MAG560 show the ledge from the side and the front quarters only (a check on where it is, not on its shape in plan)."},{"id":"patent-bottom","value":0.297,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 fe9c4793263a (US D691,233 S (Magpul), sheet 4: FIG. 4 top plan and FIG. 5 bottom plan, 300 dpi)","scaleRef":"the sheet's own scale: its two plans' widest rows (FIG. 4 row 1630, 381 px; FIG. 5 row 1763, 384 px: the floorplate) over the front elevation's floorplate width (profiles.front, 2 x 0.552 in): 346.5 px/in, ± 1% (FIG. 4's length, rows 1194 to 2219 over the side outline's 2.994 in, reads 1.2% smaller); across from each figure's own middle (FIG. 4 column 853.4, FIG. 5 column 1667.5)","method":"FIG. 5: the same edge on row 1196, its two ends at columns 1564.5 and 1770.5 (103 px each side); ± 4 px","via":"harvest"},"note":"This magazine's own design patent. Primary Arms' and Magpul's views of MAG560 show the ledge from the side and the front quarters only (a check on where it is, not on its shape in plan)."}],"adopt":{"from":"patent-top","reason":"The view from above, where the ledge's top edge is the outline; the two plans agree within their ±."},"note":"The stop is a ledge standing out behind the spine at the grip frame's top (the anchor's note: its tip is stop_behind_spine behind the spine's face), what the magazine stops against under a well: seen from above and below its rear face is flat across the middle, its corners round, and its sides lean out going forward until they meet the frame's top band. The 30-round GEN M3's patent draws the same ledge (magpul-pmag-30-gen-m3.stop_*), within 0.02 in of these figures."},"stop_side_angle":{"label":"The over-travel stop: how far its sides lean out from the magazine's length, going forward from its rounded corners","kind":"angle","measurements":[{"id":"patent-top","value":18.4,"unit":"deg","pm":1.7,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 fe9c4793263a (US D691,233 S (Magpul), sheet 4: FIG. 4 top plan and FIG. 5 bottom plan, 300 dpi)","scaleRef":"the sheet's own scale: its two plans' widest rows (FIG. 4 row 1630, 381 px; FIG. 5 row 1763, 384 px: the floorplate) over the front elevation's floorplate width (profiles.front, 2 x 0.552 in): 346.5 px/in, ± 1% (FIG. 4's length, rows 1194 to 2219 over the side outline's 2.994 in, reads 1.2% smaller); across from each figure's own middle (FIG. 4 column 853.4, FIG. 5 column 1667.5)","method":"FIG. 4: the outline's outer edge, both sides, on rows 1215 to 1263 (21 to 69 px behind the rear edge, row 1194): 127.0, 129.75, 131.5, 133.75, 135.5, 137.5, 139.25, 141.25, 143.0 px from the middle: 16 px out over 48 px along (0.333); FIG. 5 the same within 2 px; ± 1 px a reading","via":"harvest"},"note":"This magazine's own design patent. Primary Arms' and Magpul's views of MAG560 show the ledge from the side and the front quarters only (a check on where it is, not on its shape in plan)."}],"note":"Each side is straight from where its corner's round ends to where it meets the frame's top band (stop_length), out to stop_half_width there."},"stop_half_width":{"label":"The over-travel stop: half its widest, where its sides meet the frame's top band","kind":"length","measurements":[{"id":"patent-rear","value":0.426,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 b1e83c27171f (US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet as FIG. 6, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in; across from the figure's own middle column (1702.75, between the frame's silhouette lines 1528 and 1877.5, and the rib's)","method":"FIG. 7: the ledge's two end lines, columns 1545 to 1547 and 1859.5 on rows 1762 to 1798 (156.75 px each side of the middle); ± 2 px","via":"harvest"},"note":"This magazine's own design patent. Primary Arms' and Magpul's views of MAG560 show the ledge from the side and the front quarters only (a check on where it is, not on its shape in plan)."},{"id":"patent-top","value":0.423,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 fe9c4793263a (US D691,233 S (Magpul), sheet 4: FIG. 4 top plan and FIG. 5 bottom plan, 300 dpi)","scaleRef":"the sheet's own scale: its two plans' widest rows (FIG. 4 row 1630, 381 px; FIG. 5 row 1763, 384 px: the floorplate) over the front elevation's floorplate width (profiles.front, 2 x 0.552 in): 346.5 px/in, ± 1% (FIG. 4's length, rows 1194 to 2219 over the side outline's 2.994 in, reads 1.2% smaller); across from each figure's own middle (FIG. 4 column 853.4, FIG. 5 column 1667.5)","method":"FIG. 4: the side's line where it meets the band's (rows 1269 to 1275: 145.75 to 151.75 px from the middle, its run ending at 146.5); ± 3 px","via":"harvest"},"note":"This magazine's own design patent. Primary Arms' and Magpul's views of MAG560 show the ledge from the side and the front quarters only (a check on where it is, not on its shape in plan)."}],"adopt":{"from":"patent-rear","reason":"The view that looks across the ledge's widest; the plan agrees within the two readings' ±."},"note":"The rear elevation sees it as the ledge's two ends, inside the frame's silhouette: the stop is narrower than the frame."},"stop_length":{"label":"The over-travel stop: how far forward of its rear face its sides run before they meet the frame's top band","kind":"length","measurements":[{"id":"patent-top","value":0.224,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 fe9c4793263a (US D691,233 S (Magpul), sheet 4: FIG. 4 top plan and FIG. 5 bottom plan, 300 dpi)","scaleRef":"the sheet's own scale: its two plans' widest rows (FIG. 4 row 1630, 381 px; FIG. 5 row 1763, 384 px: the floorplate) over the front elevation's floorplate width (profiles.front, 2 x 0.552 in): 346.5 px/in, ± 1% (FIG. 4's length, rows 1194 to 2219 over the side outline's 2.994 in, reads 1.2% smaller); across from each figure's own middle (FIG. 4 column 853.4, FIG. 5 column 1667.5)","method":"FIG. 4: the side's straight run ends between rows 1269 and 1275 (75 and 81 px behind the rear edge: 145.75 then 151.75 px out, against a third of a pixel a row before), 77.5 px; FIG. 5 the same (rows 1269 to 1275: 144.5 then 152.5); ± 3 px","via":"harvest"},"note":"This magazine's own design patent. Primary Arms' and Magpul's views of MAG560 show the ledge from the side and the front quarters only (a check on where it is, not on its shape in plan)."}]},"stop_lip_depth_middle":{"label":"The over-travel stop: how far down its rear face comes in the middle, under the ledge's top where it meets the spine","kind":"length","measurements":[{"id":"patent-rear","value":0.174,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 b1e83c27171f (US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet as FIG. 6, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in; across from the figure's own middle column (1702.75, between the frame's silhouette lines 1528 and 1877.5, and the rib's)","method":"FIG. 7: the face's lower edge, the middle of its pair of lines, on columns 1652, 1754, 1629 and 1776 (rows 1815.5 to 1816 and 1823: 1819.4), against the ledge's top edge at row 1755.5 (columns 1606 to 1844); ± 3 px","via":"harvest"},"note":"This magazine's own design patent. Primary Arms' and Magpul's views of MAG560 show the ledge from the side and the front quarters only (a check on where it is, not on its shape in plan)."}],"note":"Each of the stop's depths is read under the ledge's top edge as the rear elevation draws it, its highest, where it meets the spine's face (FIG. 7's row 1755.5 is 2.963 in under the lips on the figure's own scale; the side outline's top crosses the spine's face at 2.972, falling to 3.01 at the tip, the ledge drawn rounded over). The rear face is deepest across the middle, shallower toward its ends: under the face, the stop is hollow either side of the gusset (stop_bay_half_width) and its outer parts slope up to the face's lower edge (stop_wing_*)."},"stop_lip_level_half_width":{"label":"The over-travel stop: how far out from the middle its rear face keeps its middle depth","kind":"length","measurements":[{"id":"patent-rear","value":0.262,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 b1e83c27171f (US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet as FIG. 6, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in; across from the figure's own middle column (1702.75, between the frame's silhouette lines 1528 and 1877.5, and the rib's)","method":"FIG. 7: the face's lower edge at its middle depth out to columns 1606 and 1799 (rows 1814.5 to 1815 and 1823); at columns 1584 and 1822 it has risen to rows 1802.5 and 1810.5","via":"harvest"},"note":"This magazine's own design patent. Primary Arms' and Magpul's views of MAG560 show the ledge from the side and the front quarters only (a check on where it is, not on its shape in plan)."}]},"stop_lip_depth_end":{"label":"The over-travel stop: how far down its rear face comes toward its ends","kind":"length","measurements":[{"id":"patent-rear","value":0.128,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 b1e83c27171f (US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet as FIG. 6, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in; across from the figure's own middle column (1702.75, between the frame's silhouette lines 1528 and 1877.5, and the rib's)","method":"FIG. 7: the face's lower edge on columns 1561 and 1844 (rows 1798 to 1798.5 and 1806.5 to 1807: 1802.6), 47.1 px under the top edge; at columns 1584 and 1822, between the two, 0.139 in (a straight line between this and the middle depth has 0.151); at 1548 and 1857, 0.139; ± 3 px","via":"harvest"},"note":"This magazine's own design patent. Primary Arms' and Magpul's views of MAG560 show the ledge from the side and the front quarters only (a check on where it is, not on its shape in plan)."}]},"stop_lip_end_half_width":{"label":"The over-travel stop: how far out from the middle the rear face's lower edge reaches stop_lip_depth_end","kind":"length","measurements":[{"id":"patent-rear","value":0.385,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 b1e83c27171f (US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet as FIG. 6, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in; across from the figure's own middle column (1702.75, between the frame's silhouette lines 1528 and 1877.5, and the rib's)","method":"FIG. 7: columns 1561 and 1844, where stop_lip_depth_end is read (141.5 px from the middle); outward of it the edge turns down into the ledge's rounded end","via":"harvest"},"note":"This magazine's own design patent. Primary Arms' and Magpul's views of MAG560 show the ledge from the side and the front quarters only (a check on where it is, not on its shape in plan)."}]},"stop_wing_depth":{"label":"The over-travel stop: under its outer parts, how far below the ledge's top the sloping underside comes at stop_wing_half_width","kind":"length","measurements":[{"id":"patent-rear","value":0.169,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 b1e83c27171f (US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet as FIG. 6, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in; across from the figure's own middle column (1702.75, between the frame's silhouette lines 1528 and 1877.5, and the rib's)","method":"FIG. 7: columns 1561 and 1844, the line at rows 1817 to 1818 under the face's lower edge's pair (the pair at 1838 and 1848 under it is the band's corner, as at the next columns in: 1849.5 and 1851.5), 62 px under the top edge; ± 4 px","via":"harvest"},"note":"This magazine's own design patent. Primary Arms' and Magpul's views of MAG560 show the ledge from the side and the front quarters only (a check on where it is, not on its shape in plan)."}],"note":"The rear elevation draws a second edge under each end of the face, coming down from near the ledge's end to the spine's edge where the frame's top band ends: the underside of the ledge's outer parts, which slopes down from the face's lower edge going forward. Drawn as ruled from the face's lower edge at the rear to a straight edge at the spine's face, from this point down to the spine's edge at the top of the first row (FIG. 7's edge reads 0.214 in under the top at columns 1584 and 1822 and 0.215 at 1606 and 1799, where that line has 0.19 and 0.21)."},"stop_wing_half_width":{"label":"The over-travel stop: how far out from the middle stop_wing_depth is read","kind":"length","measurements":[{"id":"patent-rear","value":0.385,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 b1e83c27171f (US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet as FIG. 6, 300 dpi)","scaleRef":"magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in; across from the figure's own middle column (1702.75, between the frame's silhouette lines 1528 and 1877.5, and the rib's)","method":"FIG. 7: columns 1561 and 1844 (141.5 px from the middle)","via":"harvest"},"note":"This magazine's own design patent. Primary Arms' and Magpul's views of MAG560 show the ledge from the side and the front quarters only (a check on where it is, not on its shape in plan)."}]},"stop_bay_half_width":{"label":"The over-travel stop: under it, how far out from the middle the hollow either side of the gusset reaches at the rear face","kind":"length","measurements":[{"id":"patent-bottom","value":0.28,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-pmag-20-gen-m3 fe9c4793263a (US D691,233 S (Magpul), sheet 4: FIG. 4 top plan and FIG. 5 bottom plan, 300 dpi)","scaleRef":"the sheet's own scale: its two plans' widest rows (FIG. 4 row 1630, 381 px; FIG. 5 row 1763, 384 px: the floorplate) over the front elevation's floorplate width (profiles.front, 2 x 0.552 in): 346.5 px/in, ± 1% (FIG. 4's length, rows 1194 to 2219 over the side outline's 2.994 in, reads 1.2% smaller); across from each figure's own middle (FIG. 4 column 853.4, FIG. 5 column 1667.5)","method":"FIG. 5: the wall's pair of lines, both sides, on rows 1215, 1221 and 1227 (21, 27, 33 px ahead of the rear edge, row 1194): (1577, 1586.5 | 1748, 1758), (1580.5, 1590.5 | 1743.5, 1754), (1582.5, 1594.5 | 1740.5, 1753): their middles 85.6, 81.6, 79.1 px from the middle; a line through them, 97.0 - 0.54 x px, at the rear edge; ± 3 px (the rows further forward run into the gusset's and the bars' lines)","via":"harvest"},"note":"This magazine's own design patent. Primary Arms' and Magpul's views of MAG560 show the ledge from the side and the front quarters only (a check on where it is, not on its shape in plan)."}],"note":"FIG. 5 (from below) draws each hollow's outer wall as a straight line from the rear face forward and in toward the spine's edge at the spine's face (it reaches the spine's half width, 0.219 in, 0.112 in ahead of the rear face). The hollow's roof is the face's lower edge in the middle (stop_lip_depth_middle)."}}},{"subject":"magpul-pmag-30-gen-m3","title":"Magpul PMAG 30 AR/M4 GEN M3","dimensions":{"overall_height":{"label":"Overall height, feed lips to base","kind":"length","measurements":[{"id":"magpul","value":7.5,"unit":"in","pm":0.1,"stated":"Length, max: 7.5 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, PMAG 30 AR/M4 GEN M3 (MAG557), specifications","url":"https://magpul.com/pmag-30-ar-m4-gen-m3.html","retrieved":"2026-10-02","via":"harvest"}}],"note":"Magpul's 'Length, max', read as the height standing upright (its top level): the curve's diagonal would be about 1% more, which the ± covers. The patent's side elevation is scaled by it."},"body_height":{"label":"Body height below the feed-lip block","kind":"length","measurements":[],"note":"Onboarding checklist: Side view; overall_height minus the feed-lip block when the block is shared across a product line."},"feed_lip_block_height":{"label":"Feed-lip block height","kind":"length","measurements":[],"note":"Onboarding checklist."},"front_to_back":{"label":"Front to back at the body top","kind":"length","measurements":[{"id":"patent","value":2.528,"unit":"in","pm":0.035,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 e9f276159e55 (US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 2 right side elevation, 300 dpi)","scaleRef":"scale from magpul-pmag-30-gen-m3.overall_height = 7.5 in (y-extent 2599 px → 346.5 px/in)","method":"width in y [-1.2, -0.6] of the traced outline (tools/trace.py); the body's front to back below the feed lips, where it is straight (it fits the magwell there)","via":"harvest"}}],"note":"Onboarding checklist: Side view; same calibration as the heights."},"spine_ahead_of_stop":{"label":"The spine's rear face where it stands in the well, ahead of the tip of the stop on the spine below it (the side outline's rearmost point)","kind":"length","measurements":[{"id":"patent","value":0.066,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 e9f276159e55 (US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 2 right side elevation, 300 dpi)","scaleRef":"scale from magpul-pmag-30-gen-m3.overall_height = 7.5 in (y-extent 2599 px → 346.5 px/in)","method":"x_min in y [-1.2, -0.6] of the traced outline (tools/trace.py); the spine's rear face where the body is straight (it stands in the magwell there), ahead of the outline's rearmost point: the tip of the stop on the spine just under the well, where the outline's origin is","via":"harvest"}}],"note":"Where its anchor is (2026-10-05). The side outline's origin is its rearmost point, and that is the tip of the stop standing out of the spine just under the magwell, not the spine: seated by it, the magazine stood this far forward, its front face 0.06 in through the well's front wall (std.ar15.magwell_front_inner_x)."},"catch_notch_top":{"label":"Magazine catch notch (left side), its upper edge below the feed lips' top","kind":"length","measurements":[{"id":"photo","value":1.07,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 3eded591002b (Magpul's own photo of the left side, on white, the magazine leaning 7.8°, 1200 px)","scaleRef":"magpul-pmag-30-gen-m3.overall_height = 7.5 in over the photo's 1065 px from the feed lips' top to the lowest point, both measured down the body's own axis (the spine's lean: its edge at columns 760, 774, 787, 801 on rows 150 to 450): 142 px/in","method":"the notch is the dark rounded window at columns 632 to 702; its upper edge at row 215, the feed lips' top at (700, 57): 152 px down the axis (the model review of 2026-10-05, .cache/model-review/accessories-magazines; and read again by the row profile through columns 645 to 695, which darkens fastest at row 214; the lean 7.78° and 1063 px overall by the silhouette's own extent)","via":"harvest"}},{"id":"patent","value":1.12,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 e44444a8964a (US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 3 left side elevation, 300 dpi)","scaleRef":"magpul-pmag-30-gen-m3.overall_height = 7.5 in over the drawing's 2572 px","method":"the notch's upper edge at row 832, the top at row 448 (the same review's reading)","via":"harvest"},"note":"A design patent's drawing of the window model (MAG556), the same outside: a second reading, not the product's own."}],"adopt":{"from":"photo","reason":"Magpul's photograph of the product itself; the patent's drawing agrees within the two readings' ± (0.05 apart)."},"note":"What seats it: the notch's upper edge hangs on the lower's catch (2026-10-05; until then it was hung where the catalog's .22 magazine's feed lips are, 0.37 in too high, its lips above the bore's axis). Both readings are scaled by Magpul's 7.5 in read as the height standing upright; if that is the length along the curve they are 1% less."},"catch_notch_height":{"label":"Magazine catch notch (left side), its height","kind":"length","measurements":[{"id":"photo","value":0.25,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 3eded591002b (Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px)","scaleRef":"the photo's silhouette fitted to the traced side outline (mirrored, turned 7.66°, 141.5 px/in, IoU 0.987: .cache/model-fixes/pmag/reg.py), so x is from the outline's rearmost point and y from the feed lips' top","method":"the window is the darkest thing on the side (luminance under 35 of 255): the 1st to the 99th percentile of its pixels down the body, y -1.084 to -1.334 (its upper edge 0.014 in lower than catch_notch_top's reading of the same photo, within that one's ±); ± 2 px and the threshold (at 45 the block's shadow under it joins it)","via":"harvest"}},{"id":"patent","value":0.26,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 e44444a8964a (US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 3 left side elevation, 300 dpi)","scaleRef":"magpul-pmag-30-gen-m3.overall_height = 7.5 in over the drawing's 2572 px (rows 447 to 3019): 342.9 px/in; x from its rearmost column, 1895","method":"the rounded rectangle's upper and lower lines on column 1600: rows 830 to 833 and 919 to 922, centre to centre 89 px","via":"harvest"},"note":"The window model's drawing (MAG556), the same outside: a second reading."}],"adopt":{"from":"photo","reason":"Magpul's photograph of the product itself; the patent's drawing agrees within the two readings' ±."},"note":"The window the catch comes into: as tall as the slot it comes through in a lower (std.ar15.mag_catch_slot_h, 0.252 in). Scaled as catch_notch_top is."},"catch_notch_rear_x":{"label":"Magazine catch notch (left side), its rear end ahead of the side outline's rearmost point","kind":"length","measurements":[{"id":"photo","value":0.55,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 3eded591002b (Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px)","scaleRef":"the photo's silhouette fitted to the traced side outline (mirrored, turned 7.66°, 141.5 px/in, IoU 0.987: .cache/model-fixes/pmag/reg.py), so x is from the outline's rearmost point and y from the feed lips' top","method":"the window's dark pixels (luminance under 35), the 1st percentile along the body: x 0.548; ± 2 px, the threshold and the fit","via":"harvest"}},{"id":"patent","value":0.57,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 e44444a8964a (US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 3 left side elevation, 300 dpi)","scaleRef":"magpul-pmag-30-gen-m3.overall_height = 7.5 in over the drawing's 2572 px (rows 447 to 3019): 342.9 px/in; x from its rearmost column, 1895","method":"the rounded rectangle's rear line on row 878: columns 1697 to 1700, 196.5 px ahead of the rearmost column","via":"harvest"},"note":"The window model's drawing: a second reading."}],"adopt":{"from":"photo","reason":"Magpul's photograph of the product itself; the patent's drawing agrees within the two readings' ±."}},"catch_notch_front_x":{"label":"Magazine catch notch (left side), its front end ahead of the side outline's rearmost point","kind":"length","measurements":[{"id":"photo","value":1.06,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 3eded591002b (Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px)","scaleRef":"the photo's silhouette fitted to the traced side outline (mirrored, turned 7.66°, 141.5 px/in, IoU 0.987: .cache/model-fixes/pmag/reg.py), so x is from the outline's rearmost point and y from the feed lips' top","method":"the window's dark pixels (luminance under 35), the 99th percentile along the body: x 1.060 (the window 0.51 in long); ± 2 px, the threshold and the fit","via":"harvest"}},{"id":"patent","value":1.1,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 e44444a8964a (US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 3 left side elevation, 300 dpi)","scaleRef":"magpul-pmag-30-gen-m3.overall_height = 7.5 in over the drawing's 2572 px (rows 447 to 3019): 342.9 px/in; x from its rearmost column, 1895","method":"the rounded rectangle's front line on row 878: columns 1518 to 1521, 375.5 px ahead of the rearmost column (the rectangle 0.52 in long)","via":"harvest"},"note":"The window model's drawing: a second reading."}],"adopt":{"from":"photo","reason":"Magpul's photograph of the product itself; the patent's drawing reads 0.035 in further forward, within the two readings' ±."}},"catch_block_proud":{"label":"The block under the catch notch (left side), standing out of the side","kind":"length","measurements":[{"id":"patent-front","value":0.054,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 21cdc684d6f3 (US D681,151 S (Magpul), FIG. 6 front elevation, 300 dpi)","scaleRef":"magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2440 px (rows 467 to 2907): 325.3 px/in","method":"rows 918 to 957: the block's outer line at columns 950 to 954, the side's at 934 to 937: 17.5 px, centre to centre; its top a level line at rows 914 to 916 (1.377 in under the top of the lips), its chamfer from row 957 back to the side at row 981; ± 2 px","via":"harvest"},"note":"The window model's drawing (MAG556)."},{"id":"patent-rear","value":0.053,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 21cdc684d6f3 (US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi)","scaleRef":"magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2440 px (rows 467 to 2907): 325.3 px/in","method":"rows 918 to 957: the block's outer line at columns 1597 to 1601, the side's at 1615 to 1618: 17.25 px; its top at rows 914 to 916, its chamfer from row 957 to row 984; ± 2 px","via":"harvest"},"note":"The window model's drawing."}],"adopt":{"from":"patent-front","reason":"The two elevations agree within a third of a pixel; the front one is the figure the front outline is traced from."},"note":"A block as long as the notch's middle stands under it on the left side, its top a flat ledge at the notch's lower edge and its lower end chamfered back into the side: the front and rear elevations have it in profile (on the right of FIG. 6, a front elevation, and the left of FIG. 7), the left elevation and the top and bottom plans in outline. On this magazine: Magpul's left-side photo has its outline under the window with a darker band along its lower end (the shadow under something that stands out, lit from above), Magpul's close view of the top (1dd728b26229) a lit ledge under the window, Primary Arms' view from above the top (53b35012a3a4) a lit face beyond the window; none shows it in profile, so how far it stands is the patent's. NOT RECONCILED WITH THE WELL: seated by its notch (catch_notch_top on the catch's upper face), the block is below the catch's slot in a lower's left wall (std.ar15.mag_catch_slot_h, 0.252 in, the notch's own height), where the well is .898 wide (std.ar15.magwell_width), and a body as wide as the patent's with this block on it is 0.97. As drawn it stands 0.06 in into that wall. What is misread isn't found: the magazine's width in the well is 0.914 at this scale, 0.016 more than the well's already (the patent's drawing scaled by Magpul's 7.5 in)."},"catch_block_height":{"label":"The block under the catch notch, from the notch's lower edge down to where it is back in the side","kind":"length","measurements":[{"id":"patent-side","value":0.21,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 e44444a8964a (US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 3 left side elevation, 300 dpi)","scaleRef":"magpul-pmag-30-gen-m3.overall_height = 7.5 in over the drawing's 2572 px (rows 447 to 3019): 342.9 px/in; x from its rearmost column, 1895","method":"the lower rectangle on column 1600: from the rounded rectangle's lower line (rows 919 to 922) to its own lower line (rows 991 to 994), 72 px centre to centre","via":"harvest"},"note":"The window model's drawing."},{"id":"patent-front","value":0.203,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 21cdc684d6f3 (US D681,151 S (Magpul), FIG. 6 front elevation, 300 dpi)","scaleRef":"magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2440 px (rows 467 to 2907): 325.3 px/in","method":"from its top (rows 914 to 916) to where its chamfer meets the side (row 981): 66 px","via":"harvest"},"note":"The window model's drawing."}],"adopt":{"from":"patent-side","reason":"The view that has the block's whole outline; the front elevation agrees within its ±. On Magpul's photo of this magazine its top is the window's lower edge (y -1.335) and the dark under its lower end runs on to -1.65: its chamfer and its shadow together, so its end isn't read there."}},"catch_block_chamfer":{"label":"The block under the catch notch, the height of the chamfer at its lower end","kind":"length","measurements":[{"id":"patent-front","value":0.074,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 21cdc684d6f3 (US D681,151 S (Magpul), FIG. 6 front elevation, 300 dpi)","scaleRef":"magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2440 px (rows 467 to 2907): 325.3 px/in","method":"the outer line leaves its column at row 957 and meets the side's at row 981: 24 px","via":"harvest"},"note":"The window model's drawing."},{"id":"patent-rear","value":0.083,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 21cdc684d6f3 (US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi)","scaleRef":"magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2440 px (rows 467 to 2907): 325.3 px/in","method":"the outer line leaves its column at row 957 and meets the side's at row 984: 27 px","via":"harvest"},"note":"The window model's drawing."}],"adopt":{"from":"patent-front","reason":"The figure the block's stand-off is adopted from; the rear elevation agrees within its ±."}},"catch_block_length":{"label":"The block under the catch notch, its length along the magazine (front to back)","kind":"length","measurements":[{"id":"photo","value":0.375,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 3eded591002b (Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px)","scaleRef":"the photo's silhouette fitted to the traced side outline (mirrored, turned 7.66°, 141.5 px/in, IoU 0.987: .cache/model-fixes/pmag/reg.py), so x is from the outline's rearmost point and y from the feed lips' top","method":"the dark lines of its two ends on three lines across it (y -1.40, -1.46, -1.52, each the mean of ± 0.02): x 0.619 and 0.994 to 1.000; ± 2 px and the fit","via":"harvest"}},{"id":"patent","value":0.4,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 e44444a8964a (US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 3 left side elevation, 300 dpi)","scaleRef":"magpul-pmag-30-gen-m3.overall_height = 7.5 in over the drawing's 2572 px (rows 447 to 3019): 342.9 px/in; x from its rearmost column, 1895","method":"the lower rectangle's two side lines, columns 1541 and 1678: 137 px","via":"harvest"},"note":"The window model's drawing."}],"adopt":{"from":"photo","reason":"Magpul's photograph of the product itself; the patent's drawing agrees within the two readings' ±."},"note":"Centred under the notch in both: its middle 0.807 from the outline's rearmost point on the photo (the window's 0.804), 0.833 on the patent's drawing (its rounded rectangle's 0.834)."},"side_panel_depth":{"label":"The side panels' floors below the grip frame's ribs and bands","kind":"length","measurements":[{"id":"patent-front","value":0.025,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 21cdc684d6f3 (US D681,151 S (Magpul), FIG. 6 front elevation, 300 dpi)","scaleRef":"magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2440 px (rows 467 to 2907): 325.3 px/in","method":"between the bands (rows 1499 to 1691, 1811 to 1991, 2123 to 2291): the frame's silhouette at columns 629 to 631 and 943 to 946, the panels' floor line at 637 to 639 and 935 to 938: 8.0 px each side, centre to centre; ± 2 px for two lines 3 px thick","via":"harvest"},"note":"The window model's drawing (MAG556): the same frame at the front, where this magazine's panels lie on the patent's."},{"id":"patent-rear","value":0.029,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 21cdc684d6f3 (US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi)","scaleRef":"magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2440 px (rows 467 to 2907): 325.3 px/in","method":"between the bands (rows 1547 to 1763, 1907 to 2123, 2231 to 2447): the frame's silhouette at columns 1606 to 1609 and 1920 to 1923, the panels' floor line at 1615 to 1620 and 1910 to 1914: 9.8 and 9.3 px, centre to centre; ± 2 px","via":"harvest"},"note":"The window model's drawing: the rear column's panels at the spine."}],"adopt":{"from":"patent-front","reason":"The figure the front outline is traced from, so the floors come out where it has them: in the plane of the sides above the frame. The rear elevation reads 0.004 in more, within both readings' ±."},"note":"How far the frame stands out of each side (2026-10-05). The front and rear columns' panels run out to the front face and to the spine between the bands, so the front and rear elevations show their floors in profile: a line inside the frame's silhouette that runs on, straight, from the silhouette of the plain sides above the frame (FIG. 6: 638.5 and 936 above, 638 and 936.5 between the bands). The floors are the body's own sides carried down, and the frame is what stands on them. The middle column's panels and the one under the last band are closed all round and show in no profile: they are taken to the same floor (Primary Arms' photo from above the top, 53b35012a3a4, shows their walls as tall as the step at the frame's upper edge beside them). The bands' silhouette is the ribs' within a pixel in both figures: on the sides they are one level."},"side_panel_wall_run":{"label":"A side panel's wall, from its rim on the frame in to its floor's edge, as the side view has it","kind":"length","measurements":[{"id":"patent","value":0.026,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 e9f276159e55 (US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 2 right side elevation, 300 dpi)","scaleRef":"scale from magpul-pmag-30-gen-m3.overall_height = 7.5 in (y-extent 2599 px → 346.6 px/in)","method":"the two lines round each panel, its rim and its floor's edge: 8.5 and 9.5 px apart on the first middle panel's upper edge (columns 1150, 1250), 8.5 and 9.5 on its rear and front edges (row 1650), 9 on the first rear panel's front edge; ± 2 px","via":"harvest"},"note":"The window model's drawing (MAG556)."}],"note":"About as far across as the panel is deep: a wall near 45°. On Magpul's photo of this magazine (3eded591002b) the panels' edges are soft dark lines 3 to 4 px wide of 141.5 px/in, 0.02 to 0.03 in: the same."},"side_panel_corner_radius":{"label":"A side panel's corners, their radius at the middle of the wall","kind":"length","measurements":[{"id":"photo","value":0.08,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 3eded591002b (Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px)","scaleRef":"141.5 px/in (the fit of its silhouette to the side outline)","method":"the round where two edges' dark lines meet, on tiles enlarged four times: 9.5 px on the first front panel, 12.5 on the first middle one, 10 on the first rear one; the ± covers their spread and ± 2 px","via":"harvest"}}]},"frame_tab_corner_radius":{"label":"The tab on the grip frame's upper edge, the round of its two upper corners","kind":"length","measurements":[{"id":"photo","value":0.03,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 3eded591002b (Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px)","scaleRef":"the left trace's own placement of this photo (profiles.left: turned 7.66°, magpul-pmag-30-gen-m3.overall_height = 7.5 in over the silhouette's 1064 px, 141.9 px/in; x from its rearmost point, y from the feed lips' top), in the plane of the side","method":"on a tile enlarged seven times: the dark line turns from the tab's top (row 417) into each side (columns 471 and 499) within 3 to 5 px; ± covers the pick and that a line 3 px wide hides a smaller round","via":"harvest"}}],"note":"The tab stands up from the frame's upper edge 0.36 in behind the front face, 0.2 in long and 0.5 high (profiles.left, above_frame: its four middle corners). It is a piece of the side at the side's own width, standing where the side leans in toward the front face (nose_taper_length): the front elevation, FIG. 6, has its face on the plain side's silhouette (0.460 and 0.458 in from the middle at y -2.5 and -2.65, as at -2.2 over it; its inner edges at 0.425 and 0.394), and on this photo no line crosses its feet (a profile down its middle, and one each side of that, is within 2 to 3 levels of flat where the edge beside it is 6 to 9 darker): the frame's face comes down to the plain side's at its upper edge there, as the front elevation's silhouette does (0.474 at y -2.88, 0.482 at -2.93, 0.485 at -3.2). Where its sides run into the edge the photo has them turn out, about as a side panel's corner (side_panel_corner_radius): not drawn, its walls stand square on the edge."},"dot_matrix_blocks":{"label":"The dot matrix under the last band: its blocks, each side","kind":"count","measurements":[{"id":"photo","value":4,"unit":"count","source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 3eded591002b (Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px)","scaleRef":"the left trace's own placement of this photo (profiles.left: turned 7.66°, magpul-pmag-30-gen-m3.overall_height = 7.5 in over the silhouette's 1064 px, 141.9 px/in; x from its rearmost point, y from the feed lips' top), in the plane of the side","method":"a profile of the luminance along the matrix (0.4 in wide, 14.45° to the magazine's level): twelve lit walls and twelve dark ones in four threes, the threes 0.354 in apart (3.5 of the dimples' own pitch); the same four on Primary Arms' photo of the right side (8664c534ce73) and on Magpul's feature image of it (2dc1cc9f8264)","via":"harvest"}}],"note":"Magpul's sheet: \"a paint pen dot matrix has been added to the bottom panel of the body\". Its diagram of the matrix (references/magpul-pmag-30-gen-m3/docs/d31fc37728.pdf, \"MAGPUL DOT MATRIX DIAGRAM\") draws every character on a block of three by five squares. The patent's FIG. 2 and FIG. 3 draw the same four blocks."},"dot_matrix_columns":{"label":"The dot matrix: the columns of dimples in a block","kind":"count","measurements":[{"id":"photo","value":3,"unit":"count","source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 3eded591002b (Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px)","scaleRef":"the left trace's own placement of this photo (profiles.left: turned 7.66°, magpul-pmag-30-gen-m3.overall_height = 7.5 in over the silhouette's 1064 px, 141.9 px/in; x from its rearmost point, y from the feed lips' top), in the plane of the side","method":"the same profile: three lit walls and three dark ones to a block, 0.101 to 0.102 in apart","via":"harvest"}}]},"dot_matrix_rows":{"label":"The dot matrix: the rows of dimples in a block","kind":"count","measurements":[{"id":"photo","value":5,"unit":"count","source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 3eded591002b (Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px)","scaleRef":"the left trace's own placement of this photo (profiles.left: turned 7.66°, magpul-pmag-30-gen-m3.overall_height = 7.5 in over the silhouette's 1064 px, 141.9 px/in; x from its rearmost point, y from the feed lips' top), in the plane of the side","method":"a profile down each block's middle column (0.06 in wide, square to the rows), from the panel's upper edge to its lower: five dark walls in each of the four blocks, 0.100 to 0.101 in apart","via":"harvest"}}]},"dot_matrix_pitch":{"label":"The dot matrix: from one dimple's middle to the next, along a row and down a column","kind":"length","measurements":[{"id":"photo","value":0.101,"unit":"in","pm":0.003,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 3eded591002b (Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px)","scaleRef":"the left trace's own placement of this photo (profiles.left: turned 7.66°, magpul-pmag-30-gen-m3.overall_height = 7.5 in over the silhouette's 1064 px, 141.9 px/in; x from its rearmost point, y from the feed lips' top), in the plane of the side","method":"along the rows, wall to like wall: 0.104, 0.100; 0.100, 0.102; 0.102, 0.102; 0.100, 0.103 (lit walls 0.102, 0.102; 0.102, 0.100; 0.104, 0.102; 0.102, 0.101); down the columns 0.100, 0.100, 0.103, 0.100 and the like in the other three blocks; ± is the spread","via":"harvest"}}],"note":"One figure for both: the lattice is square. The blocks are 3.5 of it apart (0.354 in read), which the model takes from the blocks' own corners (profiles.left, dot_blocks)."},"dot_matrix_dimple":{"label":"The dot matrix: a dimple across, wall to wall","kind":"length","measurements":[{"id":"photo","value":0.068,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 3eded591002b (Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px)","scaleRef":"the left trace's own placement of this photo (profiles.left: turned 7.66°, magpul-pmag-30-gen-m3.overall_height = 7.5 in over the silhouette's 1064 px, 141.9 px/in; x from its rearmost point, y from the feed lips' top), in the plane of the side","method":"the lit wall to the dark wall of one dimple along the rows: 0.067, 0.069, 0.067; 0.069, 0.067, 0.069; 0.069, 0.067, 0.067; 0.069, 0.067, 0.069 (the land between two dimples 0.033 to 0.035); down the columns the land is 0.031 to 0.035, which leaves 0.066 to 0.070. Each is the middle of a wall's line to the middle of the next: ± is 1 px","via":"harvest"}}],"note":"Square, sunk into the panel's floor: on the photo each has its lit wall toward the spine and its dark one toward the front, as the panel's own walls have theirs, and Magpul's feature image of the right side (2dc1cc9f8264) has every dimple's shadow on the wall toward the light. HOW DEEP isn't in any view (no elevation draws a dimple in profile): the model sinks them six tenths of side_panel_depth, their walls' shadows on this photo being a little over half as strong as the panel's own wall's beside them (7 to 9 levels against 13). Its four walls are drawn leaning as a panel's do, as far across as the dimple is deep, about this figure (ASSUMED: on the photo a wall is a line a pixel or two wide). Their corners' round (the patent draws them round) is under the photo's grain and isn't drawn."},"front_bar_proud":{"label":"The front strip's bars, how far they stand out of the strip","kind":"length","measurements":[{"id":"photo","value":0.017,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 3eded591002b (Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px)","scaleRef":"the left trace's own placement of this photo (profiles.left: turned 7.66°, magpul-pmag-30-gen-m3.overall_height = 7.5 in over the silhouette's 1064 px, 141.9 px/in); the teeth are on the silhouette's own edge, the magazine's mid-plane","method":"the silhouette's front edge found to a quarter pixel on lines of constant height; each tooth's top over the edge on both sides of it: 0.018, 0.018, 0.015, 0.017, 0.016 in the first row, 0.020, 0.016, 0.014, 0.015, 0.015 in the second (0.019, 0.018, 0.018, 0.017, 0.017 and 0.019, 0.019, 0.018, 0.016, 0.016 on Primary Arms' photo of the right side, 8664c534ce73, at 170 px/in). The lower rows read 0.009 to 0.012 here, their edge softened by the photo's cut-out; ± is the spread of the upper two","via":"harvest"}},{"id":"patent","value":0.018,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 e9f276159e55 (US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 2 right side elevation, 300 dpi)","scaleRef":"the side trace's own placement of the figure (magpul-pmag-30-gen-m3.overall_height = 7.5 in over 2599 px: 346.6 px/in; x from its rearmost point)","method":"the figure's front edge, its outer line's outside: the teeth of the first row stand 0.015 to 0.020 over the edge beside them","via":"harvest"},"note":"The window model's drawing (MAG556), the same outside."}],"adopt":{"from":"photo","reason":"Magpul's photograph of the product itself; the patent's drawing agrees within a thousandth."},"note":"The bars are ridges across the front strip between the bands, five to a row and four in the last (profiles.left, bars_front: where each is). The bands stand as far out of the strip as out of the sides (0.02 to 0.025 in on the same edge: side_panel_depth)."},"spine_bar_proud":{"label":"The spine's bars, how far they stand out of the spine","kind":"length","measurements":[{"id":"photo","value":0.022,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 3eded591002b (Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px)","scaleRef":"the left trace's own placement of this photo (profiles.left: turned 7.66°, magpul-pmag-30-gen-m3.overall_height = 7.5 in over the silhouette's 1064 px, 141.9 px/in); the teeth are on the silhouette's own edge, the magazine's mid-plane","method":"the silhouette's rear edge, the same way: 0.022, 0.025, 0.023, 0.025 under the stop, 0.020, 0.021, 0.020, 0.022, 0.022 under the rib, 0.018, 0.016, 0.018, 0.019 in the last row (0.021 to 0.023 and 0.016 to 0.017 on Primary Arms' photo of the right side)","via":"harvest"}},{"id":"patent","value":0.016,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 e9f276159e55 (US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 2 right side elevation, 300 dpi)","scaleRef":"the side trace's own placement of the figure (magpul-pmag-30-gen-m3.overall_height = 7.5 in over 2599 px: 346.6 px/in; x from its rearmost point)","method":"the figure's rear edge: its teeth stand 0.014 to 0.017 over the edge beside them","via":"harvest"},"note":"The window model's drawing (MAG556), the same outside."}],"adopt":{"from":"photo","reason":"Magpul's photograph of the product itself, which Primary Arms' agrees with; the drawing's teeth are a little lower, within the two readings' ±."},"note":"The same ridges on the spine (profiles.left, bars_spine). The long rib down the spine's middle in the second row stands as far: no tooth shows there from the side."},"strip_bar_thickness":{"label":"A bar of the front strip or the spine, its thickness along the magazine","kind":"length","measurements":[{"id":"photo","value":0.036,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 3eded591002b (Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px)","scaleRef":"the left trace's own placement of this photo (profiles.left: turned 7.66°, magpul-pmag-30-gen-m3.overall_height = 7.5 in over the silhouette's 1064 px, 141.9 px/in); the teeth are on the silhouette's own edge, the magazine's mid-plane","method":"each tooth's length at half its height on the silhouette's edges: 0.036 to 0.048 on the front (softened by the cut-out), 0.024 to 0.032 on the spine; ± covers both","via":"harvest"}},{"id":"patent","value":0.034,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 21cdc684d6f3 (US D681,151 S (Magpul), FIG. 6 front elevation, 300 dpi)","scaleRef":"magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2437 px (rows 467 to 2907, less a line's weight): 324.9 px/in; across from the figure's own middle column","method":"a bar's two lines down a column 0.1 in off the middle: rows 1482.8 to 1494.1, 1528.1 to 1539.1, 1618.6 to 1629.6 on the front elevation (0.035, 0.034, 0.034), and 0.033 between the like lines of the rear elevation's; ± 2 px","via":"harvest"},"note":"The window model's drawing (MAG556), the same outside."}],"adopt":{"from":"photo","reason":"The product's own teeth in profile; the drawing's two elevations agree within two thousandths."}},"front_strip_width":{"label":"The front strip: the flat of the grip frame's front face, between the rounds into its sides","kind":"length","measurements":[{"id":"patent-front","value":0.44,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 21cdc684d6f3 (US D681,151 S (Magpul), FIG. 6 front elevation, 300 dpi)","scaleRef":"magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2437 px (rows 467 to 2907, less a line's weight): 324.9 px/in; across from the figure's own middle column","method":"the two lines down the front between the bands: columns 858.5 and 715.5 on rows 1515, 1538 and 2191 (0.220 each side of the middle); 857.5 and 717.2 across a band (0.217, 0.215); ± 2 px each","via":"harvest"},"note":"The window model's drawing (MAG556), the same outside."}],"note":"What the bars lie across: FIG. 6 draws each bar from one of these two lines to the other. On Primary Arms' view of the front (53b35012a3a4) the bars run across the flat and stop where the face turns into the sides."},"front_corner_depth":{"label":"The grip frame's front corners: how far behind the front face a side begins to turn in","kind":"length","measurements":[{"id":"patent-side","value":0.115,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 e9f276159e55 (US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 2 right side elevation, 300 dpi)","scaleRef":"the side trace's own placement of the figure (magpul-pmag-30-gen-m3.overall_height = 7.5 in over 2599 px: 346.6 px/in; x from its rearmost point)","method":"across the first row at y -3.4: the thin line inside the front panel at x 2.620, the front edge beside the teeth at 2.732 (0.112); across the third at y -5.2: 2.898 and 3.018 (0.120); ± 3 px","via":"harvest"},"note":"The window model's drawing (MAG556), the same outside."}],"note":"With front_strip_width, the round of the frame's front corners: a side panel's floor runs forward flat to this far behind the front face and then turns in to the front strip's edge. No view has the turn in section; it is drawn as a quarter of an ellipse between the two (ASSUMED: FIG. 6 has three lines down it, at 0.358, 0.397 and 0.426 in from the middle, which a plain round wouldn't have)."},"spine_strip_width":{"label":"The spine: the strip that stands behind the body's rear shoulders, its width","kind":"length","measurements":[{"id":"patent-rear","value":0.442,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 21cdc684d6f3 (US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi)","scaleRef":"magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2437 px (rows 467 to 2907, less a line's weight): 324.9 px/in; across from the figure's own middle column","method":"the two lines down the rear: columns 1693.3 and 1836.5 on rows 989, 1557, 1622, 1964, 2354 and 2614 (0.221, and 0.219 to 0.220, each side of the middle); ± 2 px each","via":"harvest"},"note":"The window model's drawing (MAG556), the same outside."}],"note":"The spine is narrower than the body: it runs in the well's spine slot (std.ar15.magwell_spine_slot_width, .470) and goes on down the grip frame at the same width, carrying the bars and the rib. Primary Arms' view from the rear quarter (b279a01fae08) shows it standing behind the shoulders from the feed-lip block to the floorplate."},"spine_rib_width":{"label":"The long rib down the spine's middle (second row), and the stop's gusset over the first row: their width","kind":"length","measurements":[{"id":"patent-rear","value":0.151,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 21cdc684d6f3 (US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi)","scaleRef":"magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2437 px (rows 467 to 2907, less a line's weight): 324.9 px/in; across from the figure's own middle column","method":"columns 1740.0 and 1789.3 on row 1557 (the gusset), 1740.0 and 1789.0 on rows 1964 and 2012 (the rib): 0.077 and 0.075 each side of the middle; ± 2 px each","via":"harvest"},"note":"The window model's drawing (MAG556), the same outside."}],"note":"FIG. 7 draws both between the same two lines: the gusset under the over-travel stop from its ledge down to 3.5 in under the top, the rib from the first band under it to the next. On the side photo the gusset is the slope from the stop's tip down to the spine (3.2 to 3.48 in under the top), and the rib is the straight stretch of the spine's edge from 4.11 to 5.36 with no tooth on it."},"spine_strip_proud":{"label":"The spine's strip in the grip frame: how far it stands behind the shoulder beside it","kind":"length","measurements":[{"id":"patent-side","value":0.07,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 e9f276159e55 (US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 2 right side elevation, 300 dpi)","scaleRef":"the side trace's own placement of the figure (magpul-pmag-30-gen-m3.overall_height = 7.5 in over 2599 px: 346.6 px/in; x from its rearmost point)","method":"along lines square to the spine's edge through the first and third rows: the first line ahead of the edge at 0.074 and 0.068 in; ± 3 px","via":"harvest"},"note":"The window model's drawing (MAG556), the same outside."}],"note":"Between the bands the rear panels run round the rear corners onto a shoulder, and the spine's strip stands behind it by this."},"rear_corner_depth":{"label":"The grip frame's rear corners: from the shoulder beside the spine to where a side begins to turn in","kind":"length","measurements":[{"id":"patent-side","value":0.12,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 e9f276159e55 (US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 2 right side elevation, 300 dpi)","scaleRef":"the side trace's own placement of the figure (magpul-pmag-30-gen-m3.overall_height = 7.5 in over 2599 px: 346.6 px/in; x from its rearmost point)","method":"the same two lines: the third line ahead of the spine's edge at 0.199 and 0.182 in, less the shoulder's 0.074 and 0.068 (0.125, 0.114); ± 4 px","via":"harvest"},"note":"The window model's drawing (MAG556), the same outside."}],"note":"With rear_shoulder_width, the round of the frame's rear corners, drawn as a quarter of an ellipse (ASSUMED, as the front's)."},"rear_shoulder_width":{"label":"The grip frame's rear: the width over the two shoulders beside the spine, where the rounds into the sides begin","kind":"length","measurements":[{"id":"patent-rear","value":0.554,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 21cdc684d6f3 (US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi)","scaleRef":"magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2437 px (rows 467 to 2907, less a line's weight): 324.9 px/in; across from the figure's own middle column","method":"the strongest line outside the spine's on each side: columns 1674.5 and 1854.5 on rows 1557, 1622, 1964, 2354 and 2614 (0.278 and 0.276 each side of the middle); ± 2 px each","via":"harvest"},"note":"The window model's drawing (MAG556), the same outside."}]},"spine_strip_proud_upper":{"label":"The spine above the grip frame (in the well): how far it stands behind the body's rear shoulders","kind":"length","measurements":[{"id":"patent-side","value":0.101,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 e9f276159e55 (US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 2 right side elevation, 300 dpi)","scaleRef":"the side trace's own placement of the figure (magpul-pmag-30-gen-m3.overall_height = 7.5 in over 2599 px: 346.6 px/in; x from its rearmost point)","method":"across the plain side at y -1.6 (a band 0.4 in high): the spine's edge at x 0.065, lines at 0.120, 0.166, 0.206 and 0.255; the shoulder is taken at 0.166 (FIG. 3: 0.164), where FIG. 7 has its face, and the two after it as the round into the side; ± 3 px","via":"harvest"},"note":"The window model's drawing (MAG556), the same outside."}],"note":"What runs in the well's spine slot, which is .155 deep (std.ar15.magwell_length less magwell_box_length). On the photos a line runs down the side 0.097 in ahead of the spine's edge (3eded591002b, y -1.9) and 0.118 (8664c534ce73)."},"upper_rear_corner_radius":{"label":"The body above the grip frame: the round of its rear corners, from the shoulder beside the spine into the side","kind":"length","measurements":[{"id":"patent-side","value":0.04,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 e9f276159e55 (US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 2 right side elevation, 300 dpi)","scaleRef":"the side trace's own placement of the figure (magpul-pmag-30-gen-m3.overall_height = 7.5 in over 2599 px: 346.6 px/in; x from its rearmost point)","method":"from the shoulder's line at x 0.166 to the next, 0.206, at y -1.6; ± 3 px","via":"harvest"},"note":"The window model's drawing (MAG556), the same outside."},{"id":"patent-rear","value":0.057,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 21cdc684d6f3 (US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi)","scaleRef":"magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2437 px (rows 467 to 2907, less a line's weight): 324.9 px/in; across from the figure's own middle column","method":"across at y -1.6: the line at 0.399 in from the middle to the silhouette at 0.456; ± 3 px","via":"harvest"},"note":"The window model's drawing (MAG556), the same outside."}],"adopt":{"from":"patent-rear","reason":"The elevation that looks along the corner; the side view's second line may be the round's edge or its tangent. Within the two readings' ±."}},"nose_taper_length":{"label":"The body above the grip frame: how far behind the front face its sides begin to lean in","kind":"length","measurements":[{"id":"patent-side","value":0.602,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 e9f276159e55 (US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 2 right side elevation, 300 dpi)","scaleRef":"the side trace's own placement of the figure (magpul-pmag-30-gen-m3.overall_height = 7.5 in over 2599 px: 346.6 px/in; x from its rearmost point)","method":"across the plain side at y -1.2 and -0.55: the line at x 1.989 and 1.995, the front edge at 2.591; ± 3 px","via":"harvest"},"note":"The window model's drawing (MAG556), the same outside."}],"note":"The upper body narrows toward its front face: each side leans in from this far back to nose_shoulder_width, then rounds into a front face nose_front_width wide (nose_round_depth). On MAG557: Primary Arms' view of the front (53b35012a3a4) has the lean as a facet between the side and the front, with the two ribs standing out of it; on its photo of the right side (8664c534ce73) each rib's sloped upper face is lit, a wedge from 2.14 in to the front that is 0.055 in high at the front, which at guide_rib_top_angle is a lean of 0.10 in there (the drawing's: 0.107). No line marks where the lean begins on either photo (it runs out to nothing)."},"nose_round_depth":{"label":"The body above the grip frame: how far behind the front face the lean ends and the round into the front begins","kind":"length","measurements":[{"id":"patent-side","value":0.068,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 e9f276159e55 (US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 2 right side elevation, 300 dpi)","scaleRef":"the side trace's own placement of the figure (magpul-pmag-30-gen-m3.overall_height = 7.5 in over 2599 px: 346.6 px/in; x from its rearmost point)","method":"the broken line at x 2.522 and 2.524, the front edge at 2.591; ± 3 px","via":"harvest"},"note":"The window model's drawing (MAG556), the same outside."}]},"nose_shoulder_width":{"label":"The body above the grip frame: its width where the lean ends","kind":"length","measurements":[{"id":"patent-front","value":0.7,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 21cdc684d6f3 (US D681,151 S (Magpul), FIG. 6 front elevation, 300 dpi)","scaleRef":"magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2437 px (rows 467 to 2907, less a line's weight): 324.9 px/in; across from the figure's own middle column","method":"across at y -1.2 (a band 0.4 in high): the lines at 0.350 in each side of the middle (columns 900.7 and 673.2); ± 2 px each","via":"harvest"},"note":"The window model's drawing (MAG556), the same outside."}]},"nose_front_width":{"label":"The body above the grip frame: the flat of its front face","kind":"length","measurements":[{"id":"patent-front","value":0.526,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 21cdc684d6f3 (US D681,151 S (Magpul), FIG. 6 front elevation, 300 dpi)","scaleRef":"magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2437 px (rows 467 to 2907, less a line's weight): 324.9 px/in; across from the figure's own middle column","method":"the same band: the lines at 0.265 and 0.262 in from the middle (columns 873.2 and 701.7); ± 2 px each","via":"harvest"},"note":"The window model's drawing (MAG556), the same outside."}]},"guide_rib_top_angle":{"label":"The two ribs on the upper body's front: how steeply each one's upper face rises as it goes in from the side","kind":"angle","measurements":[{"id":"patent-front","value":29,"unit":"deg","pm":3,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 21cdc684d6f3 (US D681,151 S (Magpul), FIG. 6 front elevation, 300 dpi)","scaleRef":"magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2437 px (rows 467 to 2907, less a line's weight): 324.9 px/in; across from the figure's own middle column","method":"the upper rib's upper face on the figure's left: from (0.445, -0.480) on the side to (0.255, -0.375) on the front face's edge, 0.105 up over 0.190 in; ± 3 px at each end","via":"harvest"},"note":"The window model's drawing (MAG556), the same outside."}],"note":"Each rib keeps the side's own width to the front face where the body leans in under it: a flat face flush with the side, a level lower face, and an upper face that rises toward the middle, so that from the side it shows as a wedge above the flat one, growing toward the front (profiles.left, guide_ribs: where the two are on this magazine)."},"hang_below_magwell":{"label":"Hang below the magwell when seated","kind":"length","measurements":[],"note":"Onboarding checklist: Derived: overall_height minus the insertion depth, which is fixed by the mag-catch interface. A check on the seat since M3 (the lower's magazine_seat places magazines)."},"weight":{"label":"Weight, empty","kind":"mass","measurements":[{"id":"magpul","value":5,"unit":"oz","pm":0.05,"stated":"Weight: 5 oz.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, PMAG 30 AR/M4 GEN M3 (MAG557), specifications","url":"https://magpul.com/pmag-30-ar-m4-gen-m3.html","retrieved":"2026-10-02","via":"harvest"}}]},"stated_length":{"label":"Length as the manufacturer states it (reference points undefined)","kind":"length","measurements":[{"id":"magpul","value":7.5,"unit":"in","pm":0.05,"stated":"Length, max: 7.5 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, PMAG 30 AR/M4 GEN M3 (MAG557), specifications","url":"https://magpul.com/pmag-30-ar-m4-gen-m3.html","retrieved":"2026-10-02","via":"harvest"}}]},"capacity":{"label":"Capacity","kind":"count","measurements":[{"id":"magpul","value":30,"unit":"count","stated":"Capacity: 30 rds","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, PMAG 30 AR/M4 GEN M3 (MAG557), specifications","url":"https://magpul.com/pmag-30-ar-m4-gen-m3.html","retrieved":"2026-10-02","via":"harvest"}}]},"width":{"label":"Width (side to side) of the body","kind":"length","measurements":[{"id":"patent","value":0.997,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 21cdc684d6f3 (US D681,151 S (Magpul), FIG. 6 front elevation, 300 dpi)","scaleRef":"scale from magpul-pmag-30-gen-m3.overall_height = 7.5 in (y-extent 2437 px → 324.9 px/in)","method":"width in y [-4.5, -1.5] of the traced outline (tools/trace.py); the body's width over its middle, below the top's flare and above the floorplate","via":"harvest"}}],"note":"Magpul gives none. From the patent's front elevation scaled by the height: the body below its top, where the ribs stand out a little; the patent is drawn for the window model (MAG556), the same outside."},"stop_flat_half_width":{"label":"The over-travel stop on the spine: half the width of its rear face where it is flat, before its corners round off","kind":"length","measurements":[{"id":"patent-top","value":0.304,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 7a50eb2c2f64 (US D681,151 S (Magpul), sheet 4: FIG. 4 top plan and FIG. 5 bottom plan, 300 dpi)","scaleRef":"the sheet's own scale: its two plans' widest rows (FIG. 4 row 1494, 431 px; FIG. 5 row 1490, 430 px: the floorplate) over the front elevation's floorplate width (profiles.front, 2 x 0.586 in): 367.3 px/in, ± 1% (FIG. 4's length, rows 1039.5 to 2295 over the side outline's 3.443 in, reads 0.7% smaller); across from each figure's own middle (FIG. 4 column 847.5, FIG. 5 column 1755.5, the frame's outer lines)","method":"FIG. 4: the rear edge's line on rows 1039 and 1040 from column 736 to 959 (111.5 px each side of the middle); ± 3 px","via":"harvest"},"note":"The window model's drawing (MAG556), the same outside: Primary Arms' view of MAG557 from the rear quarter (b279a01fae08) shows the same ledge, its corners rounded in plan and its gusset under it (a check, not measured)."},{"id":"patent-bottom","value":0.294,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 7a50eb2c2f64 (US D681,151 S (Magpul), sheet 4: FIG. 4 top plan and FIG. 5 bottom plan, 300 dpi)","scaleRef":"the sheet's own scale: its two plans' widest rows (FIG. 4 row 1494, 431 px; FIG. 5 row 1490, 430 px: the floorplate) over the front elevation's floorplate width (profiles.front, 2 x 0.586 in): 367.3 px/in, ± 1% (FIG. 4's length, rows 1039.5 to 2295 over the side outline's 3.443 in, reads 0.7% smaller); across from each figure's own middle (FIG. 4 column 847.5, FIG. 5 column 1755.5, the frame's outer lines)","method":"FIG. 5: the same edge on rows 1039 and 1040 from column 1648 to 1864 (108 px each side); ± 3 px","via":"harvest"},"note":"The window model's drawing (MAG556), the same outside: Primary Arms' view of MAG557 from the rear quarter (b279a01fae08) shows the same ledge, its corners rounded in plan and its gusset under it (a check, not measured)."}],"adopt":{"from":"patent-top","reason":"The view from above, where the ledge's top edge is the outline; the two plans agree within their ±."},"note":"The stop is a ledge standing out behind the spine at the grip frame's top, what the magazine stops against under a well: seen from above and below its rear face is flat across the middle, its corners round, and its sides lean out going forward until they meet the frame's top band."},"stop_side_angle":{"label":"The over-travel stop: how far its sides lean out from the magazine's length, going forward from its rounded corners","kind":"angle","measurements":[{"id":"patent-top","value":18.3,"unit":"deg","pm":1.7,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 7a50eb2c2f64 (US D681,151 S (Magpul), sheet 4: FIG. 4 top plan and FIG. 5 bottom plan, 300 dpi)","scaleRef":"the sheet's own scale: its two plans' widest rows (FIG. 4 row 1494, 431 px; FIG. 5 row 1490, 430 px: the floorplate) over the front elevation's floorplate width (profiles.front, 2 x 0.586 in): 367.3 px/in, ± 1% (FIG. 4's length, rows 1039.5 to 2295 over the side outline's 3.443 in, reads 0.7% smaller); across from each figure's own middle (FIG. 4 column 847.5, FIG. 5 column 1755.5, the frame's outer lines)","method":"FIG. 4: the outline's outer edge, both sides, on rows 1060, 1080, 1100 and 1108 (20.5 to 68.5 px behind the rear edge): 137.25, 144, 150.25, 153.25 px from the middle: 16 px out over 48 px along (0.33); FIG. 5 the same within a pixel (136, 143, 151 px at 20.5, 35.5, 60.5); ± 1 px a reading","via":"harvest"},"note":"The window model's drawing (MAG556), the same outside: Primary Arms' view of MAG557 from the rear quarter (b279a01fae08) shows the same ledge, its corners rounded in plan and its gusset under it (a check, not measured)."}],"note":"Each side is straight from where its corner's round ends to where it meets the frame's top band (stop_length), out to stop_half_width there."},"stop_half_width":{"label":"The over-travel stop: half its widest, where its sides meet the frame's top band","kind":"length","measurements":[{"id":"patent-rear","value":0.431,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 21cdc684d6f3 (US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi)","scaleRef":"magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2437 px (rows 467 to 2907, less a line's weight): 324.9 px/in; across from the figure's own middle column (1765, between the spine's two lines and the gusset's)","method":"FIG. 7: the ledge's two end lines, columns 1625.0 and 1905.0 on rows 1460 to 1505 (140 px each side of the middle); ± 2 px","via":"harvest"},"note":"The window model's drawing (MAG556), the same outside: Primary Arms' view of MAG557 from the rear quarter (b279a01fae08) shows the same ledge, its corners rounded in plan and its gusset under it (a check, not measured)."},{"id":"patent-top","value":0.425,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 7a50eb2c2f64 (US D681,151 S (Magpul), sheet 4: FIG. 4 top plan and FIG. 5 bottom plan, 300 dpi)","scaleRef":"the sheet's own scale: its two plans' widest rows (FIG. 4 row 1494, 431 px; FIG. 5 row 1490, 430 px: the floorplate) over the front elevation's floorplate width (profiles.front, 2 x 0.586 in): 367.3 px/in, ± 1% (FIG. 4's length, rows 1039.5 to 2295 over the side outline's 3.443 in, reads 0.7% smaller); across from each figure's own middle (FIG. 4 column 847.5, FIG. 5 column 1755.5, the frame's outer lines)","method":"FIG. 4: the side's line where it meets the band's (row 1115, columns 690 to 695: 156 px from the middle); ± 3 px","via":"harvest"},"note":"The window model's drawing (MAG556), the same outside: Primary Arms' view of MAG557 from the rear quarter (b279a01fae08) shows the same ledge, its corners rounded in plan and its gusset under it (a check, not measured)."}],"adopt":{"from":"patent-rear","reason":"The view that looks across the ledge's widest; the plan agrees within the two readings' ±."},"note":"The rear elevation sees it as the ledge's two ends, inside the frame's silhouette (0.485 each side): the stop is narrower than the frame."},"stop_length":{"label":"The over-travel stop: how far forward of its rear face its sides run before they meet the frame's top band","kind":"length","measurements":[{"id":"patent-top","value":0.206,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 7a50eb2c2f64 (US D681,151 S (Magpul), sheet 4: FIG. 4 top plan and FIG. 5 bottom plan, 300 dpi)","scaleRef":"the sheet's own scale: its two plans' widest rows (FIG. 4 row 1494, 431 px; FIG. 5 row 1490, 430 px: the floorplate) over the front elevation's floorplate width (profiles.front, 2 x 0.586 in): 367.3 px/in, ± 1% (FIG. 4's length, rows 1039.5 to 2295 over the side outline's 3.443 in, reads 0.7% smaller); across from each figure's own middle (FIG. 4 column 847.5, FIG. 5 column 1755.5, the frame's outer lines)","method":"FIG. 4: the band's line across the stop's side, rows 1113.5 to 1117 on columns 690 to 705, 75.5 px behind the rear edge (row 1039.5); FIG. 5 the same (rows 1114.5 to 1117.5 on columns 1600 to 1610); ± 3 px","via":"harvest"},"note":"The window model's drawing (MAG556), the same outside: Primary Arms' view of MAG557 from the rear quarter (b279a01fae08) shows the same ledge, its corners rounded in plan and its gusset under it (a check, not measured)."}]},"stop_lip_depth_middle":{"label":"The over-travel stop: how far down its rear face comes in the middle, under the ledge's top where it meets the spine","kind":"length","measurements":[{"id":"patent-rear","value":0.178,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 21cdc684d6f3 (US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi)","scaleRef":"magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2437 px (rows 467 to 2907, less a line's weight): 324.9 px/in; across from the figure's own middle column (1765, between the spine's two lines and the gusset's)","method":"FIG. 7: the face's lower edge, the middle of its pair of lines, on columns 1700, 1720 (rows 1496.5/1503, 1502.5), and the gusset's top at 1500.5 on column 1765, against the ledge's top edge at row 1442 (columns 1640 and 1660); ± 3 px","via":"harvest"},"note":"The window model's drawing (MAG556), the same outside: Primary Arms' view of MAG557 from the rear quarter (b279a01fae08) shows the same ledge, its corners rounded in plan and its gusset under it (a check, not measured)."}],"note":"Each of the stop's depths is read under the ledge's top edge as the rear elevation draws it, which is its highest, where it meets the spine's face (FIG. 7's row 1442 is 3.00 in under the lips on the figure's own scale; the side outline's top crosses the spine's face at 2.998, falling to 3.04 at the tip as the side elevation draws the ledge rounded over). The rear elevation draws the rear face deepest across the middle (to where the gusset begins under it), shallower toward its ends: under the face, the stop is hollow either side of the gusset (stop_bay_half_width) and its outer parts slope up to the face's lower edge (stop_wing_*)."},"stop_lip_level_half_width":{"label":"The over-travel stop: how far out from the middle its rear face keeps its middle depth","kind":"length","measurements":[{"id":"patent-rear","value":0.262,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 21cdc684d6f3 (US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi)","scaleRef":"magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2437 px (rows 467 to 2907, less a line's weight): 324.9 px/in; across from the figure's own middle column (1765, between the spine's two lines and the gusset's)","method":"FIG. 7: the face's lower edge at its middle depth out to column 1680 (rows 1495.5/1502.5); at column 1660 it has risen to rows 1485/1493","via":"harvest"},"note":"The window model's drawing (MAG556), the same outside: Primary Arms' view of MAG557 from the rear quarter (b279a01fae08) shows the same ledge, its corners rounded in plan and its gusset under it (a check, not measured)."}]},"stop_lip_depth_end":{"label":"The over-travel stop: how far down its rear face comes toward its ends","kind":"length","measurements":[{"id":"patent-rear","value":0.103,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 21cdc684d6f3 (US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi)","scaleRef":"magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2437 px (rows 467 to 2907, less a line's weight): 324.9 px/in; across from the figure's own middle column (1765, between the spine's two lines and the gusset's)","method":"FIG. 7: the face's lower edge on column 1640 (rows 1471.5/1479.5), 33.5 px under the top edge; at column 1660, between the two (rows 1485/1493: 0.145 in), as a straight line between this and the middle depth puts it; ± 3 px","via":"harvest"},"note":"The window model's drawing (MAG556), the same outside: Primary Arms' view of MAG557 from the rear quarter (b279a01fae08) shows the same ledge, its corners rounded in plan and its gusset under it (a check, not measured)."}]},"stop_lip_end_half_width":{"label":"The over-travel stop: how far out from the middle the rear face's lower edge reaches stop_lip_depth_end","kind":"length","measurements":[{"id":"patent-rear","value":0.385,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 21cdc684d6f3 (US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi)","scaleRef":"magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2437 px (rows 467 to 2907, less a line's weight): 324.9 px/in; across from the figure's own middle column (1765, between the spine's two lines and the gusset's)","method":"FIG. 7: column 1640, where stop_lip_depth_end is read (125 px from the middle); outward of it the edge turns down into the ledge's rounded end","via":"harvest"},"note":"The window model's drawing (MAG556), the same outside: Primary Arms' view of MAG557 from the rear quarter (b279a01fae08) shows the same ledge, its corners rounded in plan and its gusset under it (a check, not measured)."}]},"stop_wing_depth":{"label":"The over-travel stop: under its outer parts, how far below its top the sloping underside comes at stop_wing_half_width","kind":"length","measurements":[{"id":"patent-rear","value":0.156,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 21cdc684d6f3 (US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi)","scaleRef":"magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2437 px (rows 467 to 2907, less a line's weight): 324.9 px/in; across from the figure's own middle column (1765, between the spine's two lines and the gusset's)","method":"FIG. 7: column 1640, the lower edge's pair of lines at rows 1487.5 and 1498 (their middle 1492.75), 50.75 px under the top edge; ± 3 px","via":"harvest"},"note":"The window model's drawing (MAG556), the same outside: Primary Arms' view of MAG557 from the rear quarter (b279a01fae08) shows the same ledge, its corners rounded in plan and its gusset under it (a check, not measured)."}],"note":"The rear elevation draws a second edge under each end of the face, coming down from near the ledge's end to the spine's edge where the frame's top band ends: the underside of the ledge's outer parts, which slopes down from the face's lower edge going forward (the side elevation, FIG. 2, draws it as a sloping face under the ledge's end). Drawn as ruled from the face's lower edge at the rear to a straight edge at the spine's face, from this point down to the spine's edge at the top of the first row: FIG. 7's edge at column 1660 reads 0.205 in under the top where that line has 0.178, the difference being where the figure and the side outline put the band's lower edge (FIG. 7 0.24 to 0.27 under the stop's top, the side elevation and the model 0.21)."},"stop_wing_half_width":{"label":"The over-travel stop: how far out from the middle stop_wing_depth is read","kind":"length","measurements":[{"id":"patent-rear","value":0.385,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 21cdc684d6f3 (US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi)","scaleRef":"magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2437 px (rows 467 to 2907, less a line's weight): 324.9 px/in; across from the figure's own middle column (1765, between the spine's two lines and the gusset's)","method":"FIG. 7: column 1640 (125 px from the middle)","via":"harvest"},"note":"The window model's drawing (MAG556), the same outside: Primary Arms' view of MAG557 from the rear quarter (b279a01fae08) shows the same ledge, its corners rounded in plan and its gusset under it (a check, not measured)."}]},"stop_bay_half_width":{"label":"The over-travel stop: under it, how far out from the middle the hollow either side of the gusset reaches at the rear face","kind":"length","measurements":[{"id":"patent-bottom","value":0.271,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/magpul-pmag-30-gen-m3 7a50eb2c2f64 (US D681,151 S (Magpul), sheet 4: FIG. 4 top plan and FIG. 5 bottom plan, 300 dpi)","scaleRef":"the sheet's own scale: its two plans' widest rows (FIG. 4 row 1494, 431 px; FIG. 5 row 1490, 430 px: the floorplate) over the front elevation's floorplate width (profiles.front, 2 x 0.586 in): 367.3 px/in, ± 1% (FIG. 4's length, rows 1039.5 to 2295 over the side outline's 3.443 in, reads 0.7% smaller); across from each figure's own middle (FIG. 4 column 847.5, FIG. 5 column 1755.5, the frame's outer lines)","method":"FIG. 5: the wall's pair of lines, both sides, on rows 1046 to 1076 (6.5 to 36.5 px ahead of the rear edge): their middle 96.6, 95.9, 92.6, 89.0, 86.1, 84.0 px from the middle; a line through them, 99.5 - 0.42 x px, at the rear edge; ± 3 px","via":"harvest"},"note":"The window model's drawing (MAG556), the same outside: Primary Arms' view of MAG557 from the rear quarter (b279a01fae08) shows the same ledge, its corners rounded in plan and its gusset under it (a check, not measured)."}],"note":"FIG. 5 (from below) draws each hollow's outer wall as a straight line from the rear face forward and in to the spine's edge at the spine's face (it reads 0.221 in, the spine's half width, 0.12 in ahead of the rear face); FIG. 8 draws the two hollows either side of the gusset. The hollow's roof is the face's lower edge in the middle (stop_lip_depth_middle): FIG. 5 has the face's lower edge 0.01 in ahead of its upper one there, and nothing else across the hollow."}}},{"subject":"magpul-pmag-d-60","title":"Magpul PMAG D-60 AR/M4 GEN M3","dimensions":{"overall_height":{"label":"Overall height, feed lips to the drum's lowest point, standing with the drum's two faces upright","kind":"length","measurements":[{"id":"magpul","value":7.4,"unit":"in","pm":0.05,"stated":"Length, max 7.4 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, PMAG D-60 AR/M4 GEN M3 (MAG576), technical specifications","url":"https://magpul.com/pmag-d-60-ar-m4-gen-m3.html","retrieved":"2026-10-06","via":"harvest"}}],"note":"Magpul's 'Length, max', read as the height of the magazine standing as the studio photo from the rear has it, square to the rear cover (9a2a10cb54cb: nothing of the roof or the lever shows over the collar, which a drum hanging nose up under an upright tower would show behind it; its hub's rim reads 0.990 as tall as wide, between square on and the 0.985 of a 10 degree lean, so that doesn't say): the silhouette is 1180 px tall and 654 px wide, 1.804 to 1, and Magpul's 7.4 to 4.1 is 1.805. With the feed tower upright instead (as a magazine well holds it, the drum then nose up by tower_lean) the model is 7.36 in from the lips to its lowest point, inside the figure's last digit. Magpul's design patent draws the same pose (US D765,813 FIG. 2 to 5) but its figure is 1.757 to 1 (FIG. 3: 2132 by 1212 px): its broken-line tower is about 0.2 in shorter than the product's."},"body_height":{"label":"Body height below the feed-lip block","kind":"length","measurements":[],"note":"Onboarding checklist: Side view; overall_height minus the feed-lip block when the block is shared across a product line."},"feed_lip_block_height":{"label":"Feed-lip block height","kind":"length","measurements":[],"note":"Onboarding checklist."},"front_to_back":{"label":"Front to back at the body top","kind":"length","measurements":[{"id":"gen-m3","value":2.528,"unit":"in","pm":0.035,"source":{"type":"derived","expr":"{magpul-pmag-30-gen-m3.front_to_back}"},"note":"The feed tower taken as Magpul's GEN M3 magazine's top: on this part's own photo its width (tower_width, 0.875 in) and the ledge under its catch's window (catch_notch_lower_edge) are where the 30-round's are."},{"id":"patent","value":2.48,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/magpul-pmag-d-60 0ee2ad041291 (US D765,813 S (Magpul, 'Drum magazine for a firearm'), FIG. 4 left side elevation, 300 dpi)","scaleRef":"the drum outline's scale (tools/trace.py): magpul-pmag-d-60.drum_height = 4.487 in over 1454 px, 324.0 px/in, the height handed on from FIG. 3 scaled by magpul-pmag-d-60.stated_width = 4.1 in","method":"the tower's two long edges in broken lines, as a polygon picked on gridded enlargements (± 3 px): 815 px apart along a level line at row 1000, 803 px square to the spine","via":"harvest"},"note":"The patent's broken-line tower (unclaimed, environment): drawn a little small against the product (its width in FIG. 3 reads 0.83 in for the photo's 0.875, its top about 0.2 in short)."}],"adopt":{"from":"gen-m3","reason":"The patent draws the tower in broken lines and a little small all round; the GEN M3 figure is a traced one of the same maker's own tower, and the two agree within their ±."},"note":"The feed tower's front to back where it stands in the well. No straight side view of the D-60 itself is on file: its tower is Magpul's GEN M3 (the page: 'proven GEN M3 internals'; the name), checked on its own rear photo."},"catch_notch_top":{"label":"Magazine catch notch (left side), its upper edge below the feed lips' top","kind":"length","measurements":[{"id":"photo","value":1.1,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{.catch_notch_lower_edge} - {magpul-pmag-30-gen-m3.catch_notch_height}"},"note":"This part's own ledge under the window (its photo), less the window's height as Magpul's 30-round GEN M3 has it (0.25 in, the height of the slot a lower's catch comes through): the window itself is in no straight view of the D-60."},{"id":"patent","value":0.815,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-pmag-d-60 0ee2ad041291 (US D765,813 S (Magpul, 'Drum magazine for a firearm'), FIG. 4 left side elevation, 300 dpi)","scaleRef":"the drum outline's scale (tools/trace.py): magpul-pmag-d-60.drum_height = 4.487 in over 1454 px, 324.0 px/in, the height handed on from FIG. 3 scaled by magpul-pmag-d-60.stated_width = 4.1 in","method":"the upper edge of the rounded rectangle the patent's broken lines draw on the tower's left side, its corners picked at (1379, 800) and (1500, 779) px, below the drawn tower's top at (1598, 495), along the tower (turned 9.9°): 264 px","via":"harvest"},"note":"The patent's broken-line tower (unclaimed): its top is drawn about 0.2 in lower than the product's (the whole figure is 1.757 as tall as wide, the product's photo 1.804), so everything on it reads that much nearer the top."}],"adopt":{"from":"photo","reason":"The product's own photo, which agrees with the 30-round GEN M3's 1.07 in within its ±; the patent's tower is environment, drawn short at the top."},"note":"What seats it: the notch's upper edge hangs on the lower's catch. Two magazines for one catch and one bolt have it at one height under their lips: the 30-round GEN M3's is 1.07 in (magpul-pmag-30-gen-m3.catch_notch_top)."},"hang_below_magwell":{"label":"Hang below the magwell when seated","kind":"length","measurements":[],"note":"Onboarding checklist: Derived: overall_height minus the insertion depth, which is fixed by the mag-catch interface. Not entered: how far the drum stands under a lower depends on that lower's mouth; the part's test says it for the catalog's two (app/tests/magpul-pmag-d-60.test.ts)."},"weight":{"label":"Weight, empty (with its dust cover)","kind":"mass","measurements":[{"id":"magpul","value":20.5,"unit":"oz","pm":0.05,"stated":"Weight, w/Dust Cover: 20.5 oz.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, PMAG D-60 AR/M4 GEN M3 (MAG576), technical specifications","url":"https://magpul.com/pmag-d-60-ar-m4-gen-m3.html","retrieved":"2026-10-06","via":"harvest"}}],"note":"Magpul's figure is with the dust cover, a separate slip-on piece that comes off before the magazine goes into a rifle; no page gives the cover's own weight, so the magazine on the rifle is a little under this by an unstated amount. Soldier Systems' own scale read 20 oz (a lead: the reviewer's page is harvested, the figure not quoted here)."},"weight_loaded":{"label":"Weight, loaded with 60 rounds","kind":"mass","measurements":[{"id":"magpul","value":46,"unit":"oz","pm":0.5,"stated":"Weight, loaded ~46 oz.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, PMAG D-60 AR/M4 GEN M3 (MAG576), technical specifications","url":"https://magpul.com/pmag-d-60-ar-m4-gen-m3.html","retrieved":"2026-10-06","via":"harvest"}}],"note":"Magpul's own page says about 46 oz; sellers quoting Magpul add 'M855 NATO' (Mile High Shooting, Midwest Gun Works: discovery's leads)."},"round_weight":{"label":"One round's share of Magpul's loaded weight","kind":"mass","measurements":[{"id":"magpul","value":0.425,"unit":"oz","pm":0.01,"source":{"type":"derived","expr":"({.weight_loaded} - {.weight}) / {.capacity}"}}],"note":"What the loaded weight is worked out from in a build: Magpul's loaded figure less its empty one (which is with the dust cover: without it each round's share would be a little more), over its 60 rounds."},"stated_length":{"label":"Length as the manufacturer states it (reference points undefined)","kind":"length","measurements":[{"id":"magpul","value":7.4,"unit":"in","pm":0.05,"stated":"Length, max 7.4 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, PMAG D-60 AR/M4 GEN M3 (MAG576), technical specifications","url":"https://magpul.com/pmag-d-60-ar-m4-gen-m3.html","retrieved":"2026-10-06","via":"harvest"}}]},"stated_width":{"label":"Width as the manufacturer states it: across the drum, side to side","kind":"length","measurements":[{"id":"magpul","value":4.1,"unit":"in","pm":0.05,"stated":"Width, max: 4.1 in.","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, PMAG D-60 AR/M4 GEN M3 (MAG576), technical specifications","url":"https://magpul.com/pmag-d-60-ar-m4-gen-m3.html","retrieved":"2026-10-06","via":"harvest"}}],"note":"No page says what it is measured across. Settled on the photos: seen from the rear (9a2a10cb54cb) the widest row is across the drum's round body at the height of its axis (row 856 of 7 to 1187, 331 px above the lowest point, half the 654 px width being 327), not across the retaining clips at its corners, and the height to that width is 1.804, Magpul's 7.4 to 4.1 being 1.805: the 4.1 is the drum's diameter across the rifle. Its depth along the bore is less (drum_depth)."},"capacity":{"label":"Capacity","kind":"count","measurements":[{"id":"magpul","value":60,"unit":"count","stated":"Capacity 60 rds","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, PMAG D-60 AR/M4 GEN M3 (MAG576), technical specifications","url":"https://magpul.com/pmag-d-60-ar-m4-gen-m3.html","retrieved":"2026-10-06","via":"harvest"}}]},"tower_width":{"label":"Feed tower, width side to side where it stands in the well","kind":"length","measurements":[{"id":"photo","value":0.875,"unit":"in","pm":0.022,"source":{"type":"photo","photo":"references/magpul-pmag-d-60 9a2a10cb54cb (the studio photo of the D-60 from the rear, square to the rear cover (as hosted by Sportsman's Warehouse, 1200 px))","scaleRef":"scale from magpul-pmag-d-60.overall_height = 7.4 in (y-extent 1183 px → 159.9 px/in) and magpul-pmag-d-60.stated_width = 4.1 in (x-extent 657 px → 160.2 px/in), which agree within 0.2%; mean 160.1 px/in","method":"median row width in y [4.8, 6.4] (0.868–0.912) of the traced outline (tools/trace.py); the feed tower's width, side to side, where it stands in the magazine well","via":"harvest"}}]},"tower_lean":{"label":"The feed tower's lean from the drum's two faces (with the tower upright the drum hangs nose up by this much)","kind":"angle","measurements":[{"id":"patent","value":10,"unit":"deg","pm":2,"source":{"type":"photo","photo":"references/magpul-pmag-d-60 0ee2ad041291 (US D765,813 S (Magpul, 'Drum magazine for a firearm'), FIG. 4 left side elevation, 300 dpi)","scaleRef":"an angle: the figure's own vertical, which the drum's two faces stand on","method":"the trace tool's reading of the spine's two broken lines as drawn: rear and front 10.0° from the vertical over 0.08 to 0.3 of the figure's height (tools/trace.py's edge lean, 2026-10-06); on a polygon picked along the tower's outline the spine reads 10.1°","via":"harvest"}}],"note":"The line itself reads to a tenth of a degree; the ± is for what it is a line of: the patent's broken-line tower, environment and drawn a little small and short against the product. In the patent's side elevations the drum's faces are upright and the tower leans forward as it rises. Magpul's and Primary Arms' pictures of it in a rifle (b79663b079db, 3f4a2e72a994) show the drum hanging nose up, its faces 10 to 15 degrees off square to the bore read by eye in perspective: the same way round, and no better than that."},"clip_half_angle":{"label":"A retaining clip's half width as an angle about the drum's axis, where it stands out of the rear cover's rim","kind":"angle","measurements":[{"id":"photo","value":13.6,"unit":"deg","pm":1,"source":{"type":"photo","photo":"references/magpul-pmag-d-60 9a2a10cb54cb (the studio photo of the D-60 from the rear, as hosted by Sportsman's Warehouse, 1200 px)","scaleRef":"the rear outline's placement (tools/trace.py): magpul-pmag-d-60.overall_height = 7.4 in and magpul-pmag-d-60.stated_width = 4.1 in, which agree within 0.2% (160.1 px/in)","method":"the rear outline about the hub's centre (0, -5.375): it stands beyond 2.09 in from -58.7° to -31.7° (lower right) and from -149.4° to -122.1° (lower left): 27.0° and 27.3° across","via":"harvest"}}],"note":"The four clips are at the diagonals: the two lower ones are centred 45.2 and 44.3 degrees under the level through the hub; the two upper run into the roof's shoulders."},"clip_outer_radius":{"label":"A retaining clip's outer face from the drum's axis, at the rear","kind":"length","measurements":[{"id":"photo","value":2.3,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-pmag-d-60 9a2a10cb54cb (the studio photo of the D-60 from the rear, as hosted by Sportsman's Warehouse, 1200 px)","scaleRef":"the rear outline's placement (tools/trace.py): magpul-pmag-d-60.overall_height = 7.4 in and magpul-pmag-d-60.stated_width = 4.1 in, which agree within 0.2% (160.1 px/in)","method":"the rear outline's greatest distance from the hub's centre over the two lower clips: 2.297 and 2.303 in (the upper two 2.347 and 2.351, where the roof's shoulders are behind them); the body's rim 2.05 at the level of the hub","via":"harvest"}}]},"hub_axis_below_top":{"label":"The drum's axis (the rear cover's hub) below the feed lips' top, seen from the rear","kind":"length","measurements":[{"id":"photo","value":5.375,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-pmag-d-60 9a2a10cb54cb (the studio photo of the D-60 from the rear, as hosted by Sportsman's Warehouse, 1200 px)","scaleRef":"the rear outline's placement (tools/trace.py): magpul-pmag-d-60.overall_height = 7.4 in and magpul-pmag-d-60.stated_width = 4.1 in, which agree within 0.2% (160.1 px/in)","method":"the hub's rim picked as a circle of radius 111 px centred (611, 867.5), the silhouette's top at row 7: 860.5 px","via":"harvest"}}]},"dot_square":{"label":"The dot matrix: one square's side","kind":"length","measurements":[{"id":"photo","value":0.073,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/magpul-pmag-d-60 9a2a10cb54cb (the studio photo of the D-60 from the rear, as hosted by Sportsman's Warehouse, 1200 px)","scaleRef":"the rear outline's scale, 160.1 px/in","method":"the first group's three squares on the photo enlarged 2.4 times: each 28 enlarged px (11.7 px), 7 between two (2.9 px)","via":"harvest"}}],"note":"Sixty squares, five rows of four groups of three, counted on the rear photo enlarged 2.4 times and on the patent's FIG. 3 (both show 5 by 12)."},"dot_group_gap":{"label":"The dot matrix: the gap between two groups of three","kind":"length","measurements":[{"id":"photo","value":0.088,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-pmag-d-60 9a2a10cb54cb (the studio photo of the D-60 from the rear, as hosted by Sportsman's Warehouse, 1200 px)","scaleRef":"the rear outline's scale, 160.1 px/in","method":"from the first group's last square to the second group's first: 34 enlarged px (14.2 px)","via":"harvest"}}]},"drum_height":{"label":"The drum standing as the patent draws it (its faces upright): from its lowest point to the top of the stop under the well","kind":"length","measurements":[{"id":"patent","value":4.487,"unit":"in","pm":0.056,"source":{"type":"photo","photo":"references/magpul-pmag-d-60 f4a9145d1ae8 (US D765,813 S (Magpul, 'Drum magazine for a firearm'), FIG. 3 rear elevation, 300 dpi: the drum below the feed tower)","scaleRef":"scale from magpul-pmag-d-60.stated_width = 4.1 in (x-extent 1209 px → 294.9 px/in)","method":"height of the traced outline (tools/trace.py); the drum standing as the patent draws it, from its lowest point to the top of the stop under the well (the solid lines' top, the tower's broken lines cut off above it)","via":"harvest"}}]},"drum_depth":{"label":"The drum along its own axis, from the rear cover's face to the loading lever's front","kind":"length","measurements":[{"id":"patent","value":3.595,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/magpul-pmag-d-60 0ee2ad041291 (US D765,813 S (Magpul, 'Drum magazine for a firearm'), FIG. 4 left side elevation, 300 dpi: the drum below the feed tower)","scaleRef":"scale from magpul-pmag-d-60.drum_height = 4.487 in (y-extent 1454 px → 324.0 px/in)","method":"width of the traced outline (tools/trace.py); the drum along its own axis, from the rear cover's face to the loading lever's front","via":"harvest"}},{"id":"top-plan","value":3.584,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/magpul-pmag-d-60 4f6839541f55 (US D765,813 S (Magpul, 'Drum magazine for a firearm'), FIG. 6 top plan, 300 dpi)","scaleRef":"magpul-pmag-d-60.stated_width = 4.1 in over the figure's 1167 px across (columns 692 to 1859): 284.6 px/in","method":"the figure's rows 1215 to 2235, front to rear: 1020 px","via":"harvest"}},{"id":"bottom-plan","value":3.592,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/magpul-pmag-d-60 2fb1eb509ae7 (US D765,813 S (Magpul, 'Drum magazine for a firearm'), FIG. 7 bottom plan, 300 dpi)","scaleRef":"magpul-pmag-d-60.stated_width = 4.1 in over the figure's 1250 px across (columns 643 to 1893): 304.9 px/in","method":"the figure's rows 1136 to 2231, front to rear: 1095 px","via":"harvest"}}],"adopt":{"from":"patent","reason":"The side elevation is the view the drum's outline is traced from; the two plans, each scaled by the width on its own, agree with it within 0.011 in."},"note":"What no page states: the drum's depth along the bore, less than its 4.1 in across. Three of the patent's figures, each scaled by the 4.1 in on its own, give it within 0.011 in; the plans also have the body 4.06 in across near the rear cover and 3.64 near the front, which is the taper the side elevation's lower edge has (2.05 to 1.84 in of radius): the body is round about one axis."},"catch_notch_lower_edge":{"label":"Magazine catch notch (left side), its lower edge (the top of the block under it) below the feed lips' top","kind":"length","measurements":[{"id":"photo","value":1.35,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/magpul-pmag-d-60 9a2a10cb54cb (the studio photo of the D-60 from the rear, square to the rear cover, as hosted by Sportsman's Warehouse, 1200 px)","scaleRef":"the rear outline's placement (tools/trace.py): magpul-pmag-d-60.overall_height = 7.4 in and magpul-pmag-d-60.stated_width = 4.1 in, which agree within 0.2% (160.1 px/in)","method":"the block's flat top at rows 228 to 232 (the tower's left edge at column 535 there, 543 above it), the silhouette's top at row 7: 1.396 in below the top as the photo stands, square to the rear cover, the tower leaning away by tower_lean; down the tower's own length that is (1.396 - 0.067) / cos 10°, the 0.067 being how much lower the block's rear end (0.55 in ahead of the spine, as the GEN M3's) stands than the top's highest point (0.17 ahead) for the lean; ± 2 px, the lean's ± and those two places","via":"harvest"}}],"note":"The block that stands out of the tower's left side under the catch's window shows in profile on the rear photo: a flat top and a chamfer back into the side, as on Magpul's 30-round GEN M3 (whose window's lower edge is 1.32 in under its lips)."},"catch_block_proud":{"label":"The block under the catch notch (left side), standing out of the side","kind":"length","measurements":[{"id":"photo","value":0.05,"unit":"in","pm":0.013,"source":{"type":"photo","photo":"references/magpul-pmag-d-60 9a2a10cb54cb (the studio photo of the D-60 from the rear, square to the rear cover, as hosted by Sportsman's Warehouse, 1200 px)","scaleRef":"the rear outline's placement (tools/trace.py): magpul-pmag-d-60.overall_height = 7.4 in and magpul-pmag-d-60.stated_width = 4.1 in, which agree within 0.2% (160.1 px/in)","method":"the tower's left edge at column 535 across the block's top and 543 above and below it: 8 px; ± 2 px","via":"harvest"}}],"note":"Not drawn (as on the 30-round, whose reading is 0.054 in: a body as wide as the well with this on it would stand in the well's left wall under the catch's slot)."},"tower_top_above_collar":{"label":"The feed lips' top above the upper edge of the collar round the tower's foot, as the magazine stands with its drum's faces upright","kind":"length","measurements":[{"id":"photo","value":2.852,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-pmag-d-60 9a2a10cb54cb (the studio photo of the D-60 from the rear, square to the rear cover, as hosted by Sportsman's Warehouse, 1200 px)","scaleRef":"the rear outline's placement (tools/trace.py): magpul-pmag-d-60.overall_height = 7.4 in and magpul-pmag-d-60.stated_width = 4.1 in, which agree within 0.2% (160.1 px/in)","method":"the collar's upper edge at row 462 (the step out from the tower's sides), the silhouette's top at row 7; the patent's drum, scaled by the 4.1 in width, has the stop under the well at the same height above its lowest point (drum_height 4.487 in, the photo's collar 4.539)","via":"harvest"}}]},"spine_ahead_of_rear":{"label":"The feed tower's spine, its rear face where it meets the stop on the drum's roof, ahead of the drum's rearmost point (the drum's faces upright)","kind":"length","measurements":[{"id":"patent","value":0.086,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-pmag-d-60 0ee2ad041291 (US D765,813 S (Magpul, 'Drum magazine for a firearm'), FIG. 4 left side elevation, 300 dpi)","scaleRef":"the drum outline's scale (tools/trace.py): magpul-pmag-d-60.drum_height = 4.487 in over 1454 px, 324.0 px/in, the height handed on from FIG. 3 scaled by magpul-pmag-d-60.stated_width = 4.1 in","method":"the spine's outer broken line meets the stop's top at column 1808 (row 1385), the figure's rearmost column being 1836: 28 px; ± 3 px and what a broken line leaves","via":"harvest"}}],"note":"Where the tower stands on the drum, fore and aft: only the patent's broken lines show it from the side."},"seam_rear_x":{"label":"The seam between the rear cover and the main body, ahead of the drum's rearmost point (along the drum's axis)","kind":"length","measurements":[{"id":"patent","value":0.59,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-pmag-d-60 0ee2ad041291 (US D765,813 S (Magpul, 'Drum magazine for a firearm'), FIG. 4 left side elevation, 300 dpi)","scaleRef":"the drum outline's scale (tools/trace.py): magpul-pmag-d-60.drum_height = 4.487 in over 1454 px, 324.0 px/in, the height handed on from FIG. 3 scaled by magpul-pmag-d-60.stated_width = 4.1 in","method":"the full-height line at column 1645 (dark over all of rows 1650 to 2650), the figure's rearmost column 1836: 191 px","via":"harvest"}}]},"seam_front_x":{"label":"The seam between the main body and the front cover, ahead of the drum's rearmost point (along the drum's axis)","kind":"length","measurements":[{"id":"patent","value":2.667,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-pmag-d-60 0ee2ad041291 (US D765,813 S (Magpul, 'Drum magazine for a firearm'), FIG. 4 left side elevation, 300 dpi)","scaleRef":"the drum outline's scale (tools/trace.py): magpul-pmag-d-60.drum_height = 4.487 in over 1454 px, 324.0 px/in, the height handed on from FIG. 3 scaled by magpul-pmag-d-60.stated_width = 4.1 in","method":"the full-height line at column 972 (dark over 750 of rows 1650 to 2650), the figure's rearmost column 1836: 864 px","via":"harvest"}}]},"clip_inner_radius":{"label":"A retaining clip's hook on the rear cover: its inner end from the drum's axis","kind":"length","measurements":[{"id":"photo","value":1.56,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/magpul-pmag-d-60 9a2a10cb54cb (the studio photo of the D-60 from the rear, square to the rear cover, as hosted by Sportsman's Warehouse, 1200 px)","scaleRef":"the rear outline's placement (tools/trace.py): magpul-pmag-d-60.overall_height = 7.4 in and magpul-pmag-d-60.stated_width = 4.1 in, which agree within 0.2% (160.1 px/in)","method":"the upper right clip's inner edge on the photo enlarged 2.4 times: 599 enlarged px from the hub's centre along the diagonal (250 px)","via":"harvest"}}]},"spine_width":{"label":"Feed tower, the spine's width (the rib down its rear face that runs in the well's slot)","kind":"length","measurements":[{"id":"photo","value":0.46,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-pmag-d-60 9a2a10cb54cb (the studio photo of the D-60 from the rear, square to the rear cover, as hosted by Sportsman's Warehouse, 1200 px)","scaleRef":"the rear outline's scale, 160.1 px/in","method":"the raised middle of the tower's rear face between its two dark edges, columns 576 to 650 on rows 150 to 440 (73 to 75 px)","via":"harvest"},"note":"Under the well's slot for it (std.ar15.magwell_spine_slot_width, 0.470)."}]},"lips_slot_width":{"label":"Feed tower, the gap between the two feed lips, seen from the rear","kind":"length","measurements":[{"id":"photo","value":0.44,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/magpul-pmag-d-60 9a2a10cb54cb (the studio photo of the D-60 from the rear, square to the rear cover, as hosted by Sportsman's Warehouse, 1200 px)","scaleRef":"the rear outline's scale, 160.1 px/in","method":"the lips' inner faces at columns 578 and 648 on rows 10 to 50 (the photo is of a loaded magazine: a round's base fills the left of the gap)","via":"harvest"}}]},"lips_slot_depth":{"label":"Feed tower, the gap between the feed lips: its floor below the lips' top, seen from the rear","kind":"length","measurements":[{"id":"photo","value":0.31,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/magpul-pmag-d-60 9a2a10cb54cb (the studio photo of the D-60 from the rear, square to the rear cover, as hosted by Sportsman's Warehouse, 1200 px)","scaleRef":"the rear outline's scale, 160.1 px/in","method":"the gap's right half is open down to row 56, the silhouette's top at row 7: 49 px","via":"harvest"}}],"note":"What shows of a loaded magazine: the floor is the next round or the follower, not a face of the tower."},"front_hub_radius":{"label":"The front cover's hub: the round face at its middle, radius","kind":"length","measurements":[{"id":"patent","value":0.495,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-pmag-d-60 0fccf578c45f (US D765,813 S (Magpul, 'Drum magazine for a firearm'), FIG. 2 front elevation, 300 dpi)","scaleRef":"magpul-pmag-d-60.stated_width = 4.1 in over the figure's 1216 px across the drum (columns 627 to 1843): 296.6 px/in; radii about the hub's centre (1236, 2127), which is 607 px above the figure's lowest point: half the width","method":"the dark pixels' distances from the centre, in rings 2 px wide: a full circle at 146 to 148 px","via":"harvest"}}],"note":"The front cover's circles are read on the patent's front elevation as lines: which way each steps is in no view in profile (the model cuts each as a groove of one depth)."},"front_hub_rim_radius":{"label":"The front cover's hub: the ring round its middle face, outer radius","kind":"length","measurements":[{"id":"patent","value":0.607,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-pmag-d-60 0fccf578c45f (US D765,813 S (Magpul, 'Drum magazine for a firearm'), FIG. 2 front elevation, 300 dpi)","scaleRef":"magpul-pmag-d-60.stated_width = 4.1 in over the figure's 1216 px across the drum (columns 627 to 1843): 296.6 px/in; radii about the hub's centre (1236, 2127), which is 607 px above the figure's lowest point: half the width","method":"a full circle at 180 px (and one at 168 to 170 inside it)","via":"harvest"}}]},"front_ring_radius":{"label":"The front cover: the circle round its dished face, radius","kind":"length","measurements":[{"id":"patent","value":1.038,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/magpul-pmag-d-60 0fccf578c45f (US D765,813 S (Magpul, 'Drum magazine for a firearm'), FIG. 2 front elevation, 300 dpi)","scaleRef":"magpul-pmag-d-60.stated_width = 4.1 in over the figure's 1216 px across the drum (columns 627 to 1843): 296.6 px/in; radii about the hub's centre (1236, 2127), which is 607 px above the figure's lowest point: half the width","method":"a full double circle at 306 to 308 px (further out, arcs at 364 to 370 and 422 to 434 px that the lever and the clips break)","via":"harvest"}}]}}},{"subject":"mas-defense-nero-12-62-handguard","title":"MAS Defense 12.62\" NERO M-LOK FREE FLOAT (Stealth Gray MAS00106380)","dimensions":{"weight":{"label":"Weight with its steel barrel nut and two screws","kind":"mass","measurements":[{"id":"mas","value":12.4,"unit":"oz","pm":0.05,"stated":"The rail, steel barrel nut and attaching screws brings the weight to 12.4oz.","source":{"type":"spec","publisher":"manufacturer","name":"MAS Defense, MAS DEFENSE 12.62\" NERO M-LOK FREE FLOAT - STEALTH GRAY (MAS00106380), description","url":"https://www.masdefense.com/MAS00106380-p/mas00106380.htm","retrieved":"2026-10-28","via":"harvest"}},{"id":"mas-fde","value":10.6,"unit":"oz","pm":0.05,"stated":"The rail, steel barrel nut and attaching screws brings the weight to 10.6oz.","source":{"type":"spec","publisher":"manufacturer","name":"MAS Defense, MAS DEFENSE 12.62\" NERO M-LOK FREE FLOAT - FDE (MAS00106362), description: the 9.87 in's figure","url":"https://www.masdefense.com/MAS00106362-p/mas00106362.htm","retrieved":"2026-10-28","via":"harvest"}}],"adopt":{"from":"mas","reason":"This colour's own page and the black one's; the FDE and OD Green pages carry the 9.87 in's description word for word (its weights and its one socket), against this length's own pictures with two sockets."},"note":"What goes on the rifle: MAS sells it with its own steel barrel nut and its two screws. MAS's pages for the 12.62 in in FDE (MAS00106362) and in OD Green (MAS00106212-ODG) say 7.2 and 10.6 oz and sockets \"at the rear position\": the 9.87 in's page's words, figure for figure; the pages for this one in Stealth Gray and in black, and every picture of it, have 9 and 12.4 oz and a socket at each end."},"rail_weight":{"label":"Weight of the handguard alone (without its barrel nut and screws)","kind":"mass","measurements":[{"id":"mas","value":9,"unit":"oz","pm":0.5,"stated":"Weight comes in at 9oz for the rail itself.","source":{"type":"spec","publisher":"manufacturer","name":"MAS Defense, MAS DEFENSE 12.62\" NERO M-LOK FREE FLOAT - STEALTH GRAY (MAS00106380), description","url":"https://www.masdefense.com/MAS00106380-p/mas00106380.htm","retrieved":"2026-10-28","via":"harvest"}},{"id":"mas-fde","value":7.2,"unit":"oz","pm":0.05,"stated":"Weight comes in at 7.2oz for the rail itself.","source":{"type":"spec","publisher":"manufacturer","name":"MAS Defense, MAS DEFENSE 12.62\" NERO M-LOK FREE FLOAT - FDE (MAS00106362), description: the 9.87 in's figure","url":"https://www.masdefense.com/MAS00106362-p/mas00106362.htm","retrieved":"2026-10-28","via":"harvest"}}],"adopt":{"from":"mas","reason":"As the weight's: the FDE page's figure is the 9.87 in's."}},"length":{"label":"Length (its rear face to its rail's front end)","kind":"length","measurements":[{"id":"mas","value":12.62,"unit":"in","pm":0.005,"stated":"MAS DEFENSE 12.62\" NERO M-LOK FREE FLOAT - STEALTH GRAY","source":{"type":"spec","publisher":"manufacturer","name":"MAS Defense, the page's title (MAS00106380)","url":"https://www.masdefense.com/MAS00106380-p/mas00106380.htm","retrieved":"2026-10-28","via":"harvest"}},{"id":"photo-rail","value":12.84,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/mas-defense-nero-12-62-handguard 853c5391290f (MAS Defense's picture of the 12.62 in in black, MAS00106312-2: from the front right and above, the pose every colour's picture has, 800 x 600)","scaleRef":"its own rail's slots on this picture, turned level (33.84 degrees): 22.0 px a pitch, 55.84 px/in (std.picatinny.slot_pitch)","method":"its 31 rail slots counted, their pitch times 30, with the land behind the rearmost slot (20 px to where the silhouette begins on the rail's row) and ahead of the foremost (28 px) each brought onto the part by the 15 in's same row: 12.84 in","via":"harvest"}},{"id":"photo-extent","value":12.82,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/mas-defense-nero-12-62-handguard 853c5391290f (MAS Defense's picture of the 12.62 in in black, MAS00106312-2: from the front right and above, the pose every colour's picture has, 800 x 600)","scaleRef":"its own rail's slots on this picture, turned level (33.84 degrees): 22.0 px a pitch, 55.84 px/in (std.picatinny.slot_pitch)","method":"the silhouette's length on the upper openings' row (710 px) brought onto the part by the 15 in's same row (whose level pictures read 15.12): 12.82 in","via":"harvest"}},{"id":"photo-plan","value":12.7,"unit":"in","pm":0.1,"source":{"type":"photo","photo":"references/mas-defense-nero-12-62-handguard b602e7d5e531 (MAS Defense's render of this length in FDE from above, beside its nut, 800 x 600)","scaleRef":"the 15 in's render of the same view (fb9e410b47d4): its silhouette 871.6 px for its 15.12 in, taken to be drawn at the same scale","method":"this one's silhouette 732.1 px end to end, its axis found as the turn that makes it narrowest (34.2, 33.5 degrees) along its axis (ends.py): a check, the renders' scale being taken as one","via":"harvest"}}],"adopt":{"from":"photo-rail","reason":"Its rail's slots counted between lands the picture shows as the 15 in's; the silhouette's length on another row reads within the ±; the title's figure stays beside it: the model's places along it are the picture's."},"note":"MAS names it 12.62 in (its title) and \"Rifle Length\"; the picture puts its rail's front end 12.84 in ahead of its rear face, 0.22 in more than the title's figure. The 15 in's title is 0.12 in short of its pictures the same way."},"inside_diameter":{"label":"Inside diameter","kind":"length","measurements":[{"id":"mas","value":1.25,"unit":"in","pm":0.005,"stated":"The slim 1.25\" inner diameter will require a slim muzzle device.","source":{"type":"spec","publisher":"manufacturer","name":"MAS Defense, MAS DEFENSE 12.62\" NERO M-LOK FREE FLOAT - STEALTH GRAY (MAS00106380), description","url":"https://www.masdefense.com/MAS00106380-p/mas00106380.htm","retrieved":"2026-10-28","via":"harvest"}}],"note":"MAS: it \"will require a slim muzzle device\" (one that passes through 1.25 in)."},"rear_x":{"label":"Its rear face ahead of the receiver's front face","kind":"length","measurements":[{"id":"family","value":-0.445,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.rear_x}","via":"harvest"}}],"note":"No picture of this length on an upper is level enough to read; taken as the 15 in's, whose rear face bears on the receiver's shoulder (where the barrel-nut thread begins) in its level pictures (MAS: \"The monolithic top rail of the handguard sits directly against the upper receiver rail\")."},"width":{"label":"Width across its side flats (the M-LOK faces at 3 and 9 o'clock)","kind":"length","measurements":[{"id":"family","value":1.6,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.width}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"rail_top_above_bore":{"label":"Its rail's top above the bore axis","kind":"length","measurements":[{"id":"family","value":1.22,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.rail_top_above_bore}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"bottom_below_bore":{"label":"Its bottom flat below the bore axis","kind":"length","measurements":[{"id":"family","value":0.85,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.bottom_below_bore}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"side_flat_top_above_bore":{"label":"The side flat's upper edge above the bore axis","kind":"length","measurements":[{"id":"family","value":0.62,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.side_flat_top_above_bore}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"side_flat_bottom_below_bore":{"label":"The side flat's lower edge below the bore axis","kind":"length","measurements":[{"id":"family","value":0.4,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.side_flat_bottom_below_bore}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"bottom_half_width":{"label":"Half the bottom flat's width","kind":"length","measurements":[{"id":"family","value":0.35,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.bottom_half_width}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"wall":{"label":"Its wall's thickness from the clamp's ring forward","kind":"length","measurements":[{"id":"family","value":0.06,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.wall}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"rail_underside_below_top":{"label":"Its rail's underside below the rail's top","kind":"length","measurements":[{"id":"family","value":0.24,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.rail_underside_below_top}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"rail_neck_below_top":{"label":"Where its upper faces meet the neck under its rail's head, below the rail's top","kind":"length","measurements":[{"id":"family","value":0.4,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.rail_neck_below_top}","via":"harvest"},"note":"The NERO's one section, as the 15 in's (an assumption there: as deep as a Picatinny clamp's jaws need)."}]},"window_length":{"label":"An upper opening's length along it, at the row's mid-height","kind":"length","measurements":[{"id":"family","value":0.55,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.window_length}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"window_bottom_above_bore":{"label":"The upper openings' lower ends above the bore axis","kind":"length","measurements":[{"id":"family","value":0.39,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.window_bottom_above_bore}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"lower_length":{"label":"A lower opening's length along it, at its mid-height","kind":"length","measurements":[{"id":"family","value":0.52,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.lower_length}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"lower_bottom_below_bore":{"label":"The lower openings' lower ends below the bore axis","kind":"length","measurements":[{"id":"family","value":0.67,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.lower_bottom_below_bore}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"qd_diameter":{"label":"Its QD sockets' holes across","kind":"length","measurements":[{"id":"family","value":0.37,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.qd_diameter}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"lug_bottom_below_bore":{"label":"The clamp's lug: its bottom below the bore axis","kind":"length","measurements":[{"id":"family","value":1.08,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.lug_bottom_below_bore}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"lug_flat_end_from_rear_face":{"label":"Where the lug's flat bottom ends, ahead of its rear face","kind":"length","measurements":[{"id":"family","value":1.18,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.lug_flat_end_from_rear_face}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"lug_end_from_rear_face":{"label":"Where the lug's sloped front meets the bottom flat","kind":"length","measurements":[{"id":"family","value":1.48,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.lug_end_from_rear_face}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"screw0_from_rear_face":{"label":"The clamp's rear screw ahead of its rear face","kind":"length","measurements":[{"id":"family","value":0.34,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.screw0_from_rear_face}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"screw_spacing":{"label":"The clamp's two screws apart","kind":"length","measurements":[{"id":"family","value":0.6,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.screw_spacing}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"screw_below_bore":{"label":"The clamp's screws below the bore axis","kind":"length","measurements":[{"id":"family","value":0.93,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.screw_below_bore}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"screw_head_diameter":{"label":"A clamp screw's head across","kind":"length","measurements":[{"id":"family","value":0.26,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.screw_head_diameter}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"screw_end_diameter":{"label":"A clamp screw's end across","kind":"length","measurements":[{"id":"family","value":0.2,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.screw_end_diameter}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"screw_head_proud":{"label":"How far a clamp screw's head stands off the lug","kind":"length","measurements":[{"id":"family","value":0.06,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.screw_head_proud}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"nut_across_flats":{"label":"Its barrel nut's wrench flats across","kind":"length","measurements":[{"id":"family","value":1.1875,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.nut_across_flats}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"height":{"label":"Height (its rail's top to its bottom flat)","kind":"length","measurements":[{"id":"derived","value":2.07,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{.rail_top_above_bore} + {.bottom_below_bore}","via":"harvest"}}]},"face_distance":{"label":"Its M-LOK faces' distance from the bore axis (one figure for all three)","kind":"length","measurements":[{"id":"derived","value":0.8,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.width} / 2","via":"harvest"}}]},"window_slant":{"label":"An upper opening's ends' lean from the upright, its top forward (seen from the side)","kind":"angle","measurements":[{"id":"family","value":30,"unit":"deg","pm":3,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.window_slant}","via":"harvest"},"note":"The 15 in's, read on its level picture: this length's picture of the same pose shows its openings at the same lean."}]},"lower_slant":{"label":"A lower opening's ends' lean from the upright, its top forward (seen from the side)","kind":"angle","measurements":[{"id":"family","value":24,"unit":"deg","pm":5,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.lower_slant}","via":"harvest"},"note":"The 15 in's, read on its level picture: this length's picture of the same pose shows its openings at the same lean."}]},"rail_slots":{"label":"Slots in its top rail","kind":"count","measurements":[{"id":"photo","value":31,"unit":"count","source":{"type":"photo","photo":"references/mas-defense-nero-12-62-handguard 853c5391290f (MAS Defense's picture of the 12.62 in in black, MAS00106312-2: from the front right and above, the pose every colour's picture has, 800 x 600)","scaleRef":"none: a count","method":"31 see-through slots along the rail's row on the picture turned level, every one 22.0 px from the next, from just ahead of the rear end to just behind the front (q3.py)","via":"harvest"}}]},"mlok_slots":{"label":"M-LOK slots in each row","kind":"count","measurements":[{"id":"photo","value":5,"unit":"count","source":{"type":"photo","photo":"references/mas-defense-nero-12-62-handguard 853c5391290f (MAS Defense's picture of the 12.62 in in black, MAS00106312-2: from the front right and above, the pose every colour's picture has, 800 x 600)","scaleRef":"none: a count","method":"5 slots in the row at the bore's level, between the round sockets (q.py)","via":"harvest"}}],"note":"Counted in the right side's row on this picture; the left's and the bottom's aren't in any picture of this length and are taken to be the same."},"window_count":{"label":"Openings in each upper face","kind":"count","measurements":[{"id":"photo","value":14,"unit":"count","source":{"type":"photo","photo":"references/mas-defense-nero-12-62-handguard 853c5391290f (MAS Defense's picture of the 12.62 in in black, MAS00106312-2: from the front right and above, the pose every colour's picture has, 800 x 600)","scaleRef":"none: a count","method":"14 see-through openings in the row under the rail (q.py); the picture from above (b602e7d5e531, the FDE render) shows 13 a side, its rearmost under the rail's logo","via":"harvest"}}]},"lower_count":{"label":"Openings in each lower face","kind":"count","measurements":[{"id":"photo","value":14,"unit":"count","source":{"type":"photo","photo":"references/mas-defense-nero-12-62-handguard 853c5391290f (MAS Defense's picture of the 12.62 in in black, MAS00106312-2: from the front right and above, the pose every colour's picture has, 800 x 600)","scaleRef":"none: a count","method":"14 see-through openings in the row under the M-LOK row (q.py)","via":"harvest"}}]},"rail_slot0_from_rear_face":{"label":"Its rail's rearmost slot's middle ahead of its rear face","kind":"length","measurements":[{"id":"photo","value":0.39,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/mas-defense-nero-12-62-handguard 853c5391290f (MAS Defense's picture of the 12.62 in in black, MAS00106312-2: from the front right and above, the pose every colour's picture has, 800 x 600)","scaleRef":"its own rail's slots on this picture, turned level (33.84 degrees): 22.0 px a pitch, 55.84 px/in (std.picatinny.slot_pitch)","method":"the rearmost slot 20 px ahead of where the silhouette begins on the rail's row; each row read from where the silhouette begins on that row, and brought onto the part by that row's offset on the 15 in's picture of the same pose (MAS00106314-2: the same turn within 0.2 degrees), whose figures are read on its level side pictures (mas-defense-nero-15-handguard) (+0.032 in on this row)","via":"harvest"}}]},"mlok_slot0_from_rear_face":{"label":"Its rearmost M-LOK slot's middle ahead of its rear face","kind":"length","measurements":[{"id":"photo","value":4.01,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/mas-defense-nero-12-62-handguard 853c5391290f (MAS Defense's picture of the 12.62 in in black, MAS00106312-2: from the front right and above, the pose every colour's picture has, 800 x 600)","scaleRef":"its own rail's slots on this picture, turned level (33.84 degrees): 22.0 px a pitch, 55.84 px/in (std.picatinny.slot_pitch)","method":"the first slot's see-through middle 231 px ahead of where the silhouette begins on the M-LOK row; each row read from where the silhouette begins on that row, and brought onto the part by that row's offset on the 15 in's picture of the same pose (MAS00106314-2: the same turn within 0.2 degrees), whose figures are read on its level side pictures (mas-defense-nero-15-handguard) (-0.124 in on this row)","via":"harvest"}}]},"window0_from_rear_face":{"label":"The rearmost upper opening's middle (at the row's mid-height) ahead of its rear face","kind":"length","measurements":[{"id":"photo","value":3.1,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/mas-defense-nero-12-62-handguard 853c5391290f (MAS Defense's picture of the 12.62 in in black, MAS00106312-2: from the front right and above, the pose every colour's picture has, 800 x 600)","scaleRef":"its own rail's slots on this picture, turned level (33.84 degrees): 22.0 px a pitch, 55.84 px/in (std.picatinny.slot_pitch)","method":"the first opening's middle 173 px ahead of where the silhouette begins on its row's mid-height; each row read from where the silhouette begins on that row, and brought onto the part by that row's offset on the 15 in's picture of the same pose (MAS00106314-2: the same turn within 0.2 degrees), whose figures are read on its level side pictures (mas-defense-nero-15-handguard) (-0.003 in on this row)","via":"harvest"}}]},"window_pitch":{"label":"The upper openings' pitch","kind":"length","measurements":[{"id":"photo","value":0.69,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/mas-defense-nero-12-62-handguard 853c5391290f (MAS Defense's picture of the 12.62 in in black, MAS00106312-2: from the front right and above, the pose every colour's picture has, 800 x 600)","scaleRef":"its own rail's slots on this picture, turned level (33.84 degrees): 22.0 px a pitch, 55.84 px/in (std.picatinny.slot_pitch)","method":"the first and last openings' middles 501 px apart over 13","via":"harvest"}}]},"lower0_from_rear_face":{"label":"The rearmost lower opening's middle (at its mid-height) ahead of its rear face","kind":"length","measurements":[{"id":"photo","value":2.33,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/mas-defense-nero-12-62-handguard 853c5391290f (MAS Defense's picture of the 12.62 in in black, MAS00106312-2: from the front right and above, the pose every colour's picture has, 800 x 600)","scaleRef":"its own rail's slots on this picture, turned level (33.84 degrees): 22.0 px a pitch, 55.84 px/in (std.picatinny.slot_pitch)","method":"the first opening's middle 135 px ahead of where the silhouette begins on its row; each row read from where the silhouette begins on that row, and brought onto the part by that row's offset on the 15 in's picture of the same pose (MAS00106314-2: the same turn within 0.2 degrees), whose figures are read on its level side pictures (mas-defense-nero-15-handguard) (-0.085 in on this row)","via":"harvest"}}]},"lower_pitch":{"label":"The lower openings' pitch","kind":"length","measurements":[{"id":"photo","value":0.69,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/mas-defense-nero-12-62-handguard 853c5391290f (MAS Defense's picture of the 12.62 in in black, MAS00106312-2: from the front right and above, the pose every colour's picture has, 800 x 600)","scaleRef":"its own rail's slots on this picture, turned level (33.84 degrees): 22.0 px a pitch, 55.84 px/in (std.picatinny.slot_pitch)","method":"the first and last openings' middles 501 px apart over 13","via":"harvest"}}]},"qd_rear_from_rear_face":{"label":"The rear QD socket's middle ahead of its rear face","kind":"length","measurements":[{"id":"photo","value":2.58,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/mas-defense-nero-12-62-handguard 853c5391290f (MAS Defense's picture of the 12.62 in in black, MAS00106312-2: from the front right and above, the pose every colour's picture has, 800 x 600)","scaleRef":"its own rail's slots on this picture, turned level (33.84 degrees): 22.0 px a pitch, 55.84 px/in (std.picatinny.slot_pitch)","method":"the socket's see-through middle 154 px ahead of where the silhouette begins on the M-LOK row; each row read from where the silhouette begins on that row, and brought onto the part by that row's offset on the 15 in's picture of the same pose (MAS00106314-2: the same turn within 0.2 degrees), whose figures are read on its level side pictures (mas-defense-nero-15-handguard) (-0.182 in for a socket on this row)","via":"harvest"}}]},"qd_front_from_rear_face":{"label":"The front QD socket's middle ahead of its rear face","kind":"length","measurements":[{"id":"photo","value":11.92,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/mas-defense-nero-12-62-handguard 853c5391290f (MAS Defense's picture of the 12.62 in in black, MAS00106312-2: from the front right and above, the pose every colour's picture has, 800 x 600)","scaleRef":"its own rail's slots on this picture, turned level (33.84 degrees): 22.0 px a pitch, 55.84 px/in (std.picatinny.slot_pitch)","method":"the socket's see-through middle 658 px ahead of where the silhouette begins on the M-LOK row; each row read from where the silhouette begins on that row, and brought onto the part by that row's offset on the 15 in's picture of the same pose (MAS00106314-2: the same turn within 0.2 degrees), whose figures are read on its level side pictures (mas-defense-nero-15-handguard) (+0.133 in for the front socket on this row)","via":"harvest"}}]},"reach_inside":{"label":"Room inside an M-LOK face for an accessory's nuts (from the face in to what runs under it)","kind":"length","measurements":[],"note":"Depends on the barrel and the gas block under it, other parts: no figure."}}},{"subject":"mas-defense-nero-15-handguard","title":"MAS Defense 15\" NERO M-LOK FREE FLOAT (Stealth Gray MAS00106384)","dimensions":{"weight":{"label":"Weight with its steel barrel nut and two screws","kind":"mass","measurements":[{"id":"mas","value":13.4,"unit":"oz","pm":0.05,"stated":"The rail, steel barrel nut and attaching screws brings the weight to 13.4oz.","source":{"type":"spec","publisher":"manufacturer","name":"MAS Defense, MAS DEFENSE 15\" NERO M-LOK FREE FLOAT - STEALTH GRAY (MAS00106384), description","url":"https://www.masdefense.com/MAS00106384-p/mas00106384.htm","retrieved":"2026-10-28","via":"harvest"}}],"note":"What goes on the rifle: MAS sells it with its own steel barrel nut and the two screws that clamp it. Without them, 10 oz (rail_weight)."},"rail_weight":{"label":"Weight of the handguard alone (without its barrel nut and screws)","kind":"mass","measurements":[{"id":"mas","value":10,"unit":"oz","pm":0.5,"stated":"Weight comes in at 10oz for the rail itself.","source":{"type":"spec","publisher":"manufacturer","name":"MAS Defense, MAS DEFENSE 15\" NERO M-LOK FREE FLOAT - STEALTH GRAY (MAS00106384), description","url":"https://www.masdefense.com/MAS00106384-p/mas00106384.htm","retrieved":"2026-10-28","via":"harvest"}}],"note":"The model's volume as aluminium is held to it (the nut and the screws aren't in the model's body)."},"length":{"label":"Length (its rear face to its rail's front end)","kind":"length","measurements":[{"id":"mas","value":15,"unit":"in","pm":0.5,"stated":"MAS DEFENSE 15\" NERO M-LOK FREE FLOAT - STEALTH GRAY","source":{"type":"spec","publisher":"manufacturer","name":"MAS Defense, the page's title (MAS00106384); the description says \"Extended Rifle Length\"","url":"https://www.masdefense.com/MAS00106384-p/mas00106384.htm","retrieved":"2026-10-28","via":"harvest"}},{"id":"photo-right","value":15.12,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 6bf562718703 (MAS Defense's gallery for its Stealth Gray builder set MDCK-AR15-SUL-NM15-STGRY, picture -2: this handguard on MAS's upper and an 80% lower, their right side seen level, muzzle to the right, 800 x 600)","scaleRef":"its own top rail's 37 slots one Picatinny pitch apart (std.picatinny.slot_pitch), their see-through middles fitted along the picture with a projective scale (rms 0.08 px; 33.4 px/in at the rearmost slot, 34.4 at the foremost)","method":"the seam between its rear face and the receiver (column 271.6, a line from the rail's foot to the lower's front, looked at at 8x) 0.350 in behind the rearmost slot's middle; the rail's front end (column 783.5) 14.766 ahead of it (side.py)","via":"harvest"}},{"id":"photo-left","value":15.12,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 0627ae73f200 (MAS Defense's gallery for the same builder set, picture -3: their left side seen level, muzzle to the left, 800 x 600)","scaleRef":"its own top rail, mirrored: 32 slots (the sixth to the last) fitted as the right side's (rms 0.15 px; 33.7 to 33.4 px/in)","method":"the seam 0.337 in behind the rearmost slot and the rail's front end 14.783 ahead of it, the slots counted from the right side's by their M-LOK rows (which agree to 0.02 in): 15.120 (side.py)","via":"harvest"}}],"adopt":{"from":"photo-right","reason":"The two side pictures agree to 0.005 in, and the title's 15 is a name; the right side's is the picture the outline is traced from."},"note":"MAS names it by its length (\"15\\\"\" in every title) and calls it \"Extended Rifle Length\"; it states no length otherwise. Both side pictures, read along its own rail, put its rail's front end 15.12 in ahead of its rear face; the body below the rail runs 0.07 in further at the bottom of its front face (a bevel the pictures show at three pixels, not drawn)."},"width":{"label":"Width across its side flats (the M-LOK faces at 3 and 9 o'clock)","kind":"length","measurements":[{"id":"photo-plan","value":1.6,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard fb9e410b47d4 (MAS Defense's gallery for the FDE 15 in, MAS00106364-3: the handguard from above beside its barrel nut and screws, 800 x 600)","scaleRef":"its own rail's top across, the standard's .835 in (std.picatinny.top_width): 48 to 49 px between the see-through windows either side of it, on the picture turned 32.4 degrees to level it","method":"the silhouette's two long edges, 92.2 px apart (91.0 to 92.5 along its length, at the 170 level), over the rail's 48.5 px: 1.90 times .835 in (planw.py)","via":"harvest"}}],"note":"Not published. The pictures from above are of the 15 in in black and in FDE (MAS's renders, the same view). Its rail's top is 1.2 in nearer the lens than the side flats' edges, which reads the flats a few percent narrow from a lens a few feet off: in the ±."},"rail_top_above_bore":{"label":"Its rail's top above the bore axis","kind":"length","measurements":[{"id":"photo-right","value":1.22,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 6bf562718703 (MAS Defense's gallery for its Stealth Gray builder set, picture -2: the right side seen level, 800 x 600)","scaleRef":"its rail's pitch at the picture's middle: 33.86 px/in","method":"the rail's tooth tops (row 218.4, where the rows over its length go half dark) above the middle of the side face's M-LOK row (rows 255.5 to 263.5 see through): 41.35 px (side.py)","via":"harvest"}},{"id":"photo-left","value":1.19,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 0627ae73f200 (MAS Defense's gallery for the same builder set, picture -3: the left side seen level, 800 x 600)","scaleRef":"its rail's pitch at the picture's middle: 33.58 px/in","method":"as the right side's: rows 221.7 and 261.5 (side.py)","via":"harvest"}}],"adopt":{"from":"photo-right","reason":"The picture the outline is traced from; the left reads 0.035 less, within both ±."},"note":"The bore's level is the middle of the side faces' M-LOK row (3 and 9 o'clock). MAS: \"The monolithic top rail of the handguard sits directly against the upper receiver rail\"; the catalog's mil-spec uppers have their rail 1.2125 above the bore (bcm-m4-upper), between the two readings."},"bottom_below_bore":{"label":"Its bottom flat below the bore axis","kind":"length","measurements":[{"id":"photo-right","value":0.85,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 6bf562718703 (the builder set's right side seen level, 800 x 600)","scaleRef":"its rail's pitch at the picture's middle: 33.86 px/in","method":"the silhouette's bottom over its length ahead of the clamp's lug (row 288.5) below the M-LOK row's middle (259.75): 28.75 px (side.py)","via":"harvest"}},{"id":"photo-left","value":0.82,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 0627ae73f200 (the builder set's left side seen level, 800 x 600)","scaleRef":"its rail's pitch at the picture's middle: 33.58 px/in","method":"as the right side's: rows 289.0 and 261.5 (side.py)","via":"harvest"}}],"adopt":{"from":"photo-right","reason":"The picture the outline is traced from; the left reads 0.03 less, within both ±."}},"height":{"label":"Height (its rail's top to its bottom flat; the clamp's lug hangs lower at the rear)","kind":"length","measurements":[{"id":"derived","value":2.07,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{.rail_top_above_bore} + {.bottom_below_bore}","via":"harvest"}}]},"inside_diameter":{"label":"Inside diameter","kind":"length","measurements":[{"id":"mas","value":1.25,"unit":"in","pm":0.005,"stated":"The slim 1.25\" inner diameter will require a slim muzzle device.","source":{"type":"spec","publisher":"manufacturer","name":"MAS Defense, MAS DEFENSE 15\" NERO M-LOK FREE FLOAT - STEALTH GRAY (MAS00106384), description; the builder set's page says \"(ID 1.25\\\")\"","url":"https://www.masdefense.com/MAS00106384-p/mas00106384.htm","retrieved":"2026-10-28","via":"harvest"}}],"note":"MAS: it \"will require a slim muzzle device\" (one that passes through 1.25 in)."},"rear_x":{"label":"Its rear face ahead of the receiver's front face (negative: behind it)","kind":"length","measurements":[{"id":"shoulder","value":-0.445,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"0in - {std.ar15.upper_barrel_thread_length}","via":"harvest"},"note":"Read on references/mas-defense-nero-15-handguard 6bf562718703 and 0627ae73f200 (the builder set's two sides seen level, 800 x 600): the seam between the receiver and its rear face, looked at at 8x on both, one line a pixel wide."}],"note":"Its rear face bears on the receiver's shoulder, where the barrel-nut thread begins (std.ar15.upper_barrel_thread_length: \"A barrel nut and a free-float handguard's rear end come back to that shoulder\"): the builder set's two side pictures show one line between the receiver and its rear face, from the rail's foot down to the lower, and no gap at 34 px/in; its ring at the rear covers the thread. MAS: \"The monolithic top rail of the handguard sits directly against the upper receiver rail.\""},"side_flat_top_above_bore":{"label":"The side flat's upper edge (where it meets the upper face) above the bore axis","kind":"length","measurements":[{"id":"photo-right","value":0.62,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 6bf562718703 (the builder set's right side seen level, 800 x 600)","scaleRef":"its rail's pitch at the picture's middle: 33.86 px/in","method":"on the solid stretch at its rear end (the logo's), the upper face reads lighter than the side flat: the step at row 238.75, 21 px above the M-LOK row's middle (looked at at 8x)","via":"harvest"}},{"id":"photo-left","value":0.6,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 0627ae73f200 (the builder set's left side seen level, 800 x 600)","scaleRef":"its rail's pitch at the picture's middle: 33.58 px/in","method":"as the right side's: row 241.25 against 261.5","via":"harvest"}}],"adopt":{"from":"photo-right","reason":"The picture the outline is traced from; the left reads 0.02 less."}},"side_flat_bottom_below_bore":{"label":"The side flat's lower edge (where it meets the lower face) below the bore axis","kind":"length","measurements":[{"id":"photo-right","value":0.4,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 6bf562718703 (the builder set's right side seen level, 800 x 600)","scaleRef":"its rail's pitch at the picture's middle: 33.86 px/in","method":"on the solid stretch at its rear end, the lower face reads lighter than the side flat: the step at row 273.1, 13.35 px below the M-LOK row's middle (8x)","via":"harvest"}},{"id":"photo-left","value":0.38,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 0627ae73f200 (the builder set's left side seen level, 800 x 600)","scaleRef":"its rail's pitch at the picture's middle: 33.58 px/in","method":"as the right side's: row 274.4 against 261.5","via":"harvest"}}],"adopt":{"from":"photo-right","reason":"The picture the outline is traced from; the left reads 0.02 less."}},"lower_face_bottom_below_bore":{"label":"Where the lower face's lit band ends, below the bore axis (a check on the section)","kind":"length","measurements":[{"id":"photo","value":0.78,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 6bf562718703 and 0627ae73f200 (the builder set's two sides seen level, 800 x 600)","scaleRef":"each picture's rail pitch at its middle: 33.86 and 33.58 px/in","method":"the lower face's lighter band ends at row 286.25 on both pictures (8x): 0.78 and 0.74 below each M-LOK row's middle","via":"harvest"}}],"note":"Not built from: the lower faces are drawn at 45 degrees to the bottom flat (bottom_half_width), and that puts their lower edge at the bottom flat, 0.85 below. The lit band ending 0.07 above it is the round of that corner."},"bottom_half_width":{"label":"Half the bottom flat's width (the 6 o'clock M-LOK face)","kind":"length","measurements":[{"id":"assumed","value":0.35,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view from below is on file. The lower faces are taken at 45 degrees from the side flat's lower edge (0.40 below the bore, 0.80 out) down to the bottom flat (0.85 below): 0.80 - 0.45.","via":"harvest"}}]},"wall":{"label":"Its wall's thickness (the faces' and the rail's underside's), from the clamp's ring forward","kind":"length","measurements":[{"id":"weight","value":0.06,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Worked out, not read: the wall at which the model weighs MAS's 10 oz for the rail itself as 6061 aluminium.","via":"harvest"}}],"note":"No picture shows into it. Worked out from MAS's weight for the rail itself (rail_weight, 10 oz): the wall that makes the model's volume, as 6061 aluminium (std.density.aluminium), weigh that, its outside and its openings as the pictures give them (the model built at 0.08 in held 7.11 cubic inches, at 0.12 in 8.63: 6.38 is 0.061; the rail head, 0.24 in deep, and the clamp ring at the rear hold 4.1 of it whatever the wall. With the neck under the head since, 2026-10-28, it holds 6.245 at 0.06: 9.79 oz). Inside it the published 1.25 in bore runs through the clamp's ring at the rear end, where the screws close it on the nut; ahead of the ring the inside is wider than the bore."},"face_distance":{"label":"Its M-LOK faces' distance from the bore axis (one figure for all three)","kind":"length","measurements":[{"id":"derived","value":0.8,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.width} / 2","via":"harvest"}}],"note":"The side flats stand 0.80 out and the bottom 0.85: the side flats' is used, so a part on the bottom face is drawn 0.05 in into it."},"rail_underside_below_top":{"label":"Its rail's underside (where the upper faces and their openings end) below the rail's top","kind":"length","measurements":[{"id":"photo-right","value":0.24,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 6bf562718703 (the builder set's right side seen level, 800 x 600)","scaleRef":"its rail's pitch at the picture's middle: 33.86 px/in","method":"the upper openings' tops (row 226.5, where the rows go from solid to 63% see-through) below the tooth tops (218.4): 8.1 px (side.py)","via":"harvest"}},{"id":"photo-left","value":0.23,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 0627ae73f200 (the builder set's left side seen level, 800 x 600)","scaleRef":"33.58 px/in","method":"as the right side's: rows 229.5 and 221.7","via":"harvest"}}],"adopt":{"from":"photo-right","reason":"The picture the outline is traced from."}},"rail_neck_below_top":{"label":"Where its upper faces meet the neck under its rail's head, below the rail's top","kind":"length","measurements":[{"id":"assumed","value":0.4,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no picture shows the neck; as deep as the clamps on file need under a Picatinny head.","via":"harvest"}}],"note":"The rail's lower faces are the standard's, carried down to its underside (rail_underside_below_top, where the upper openings end); under that a neck stands straight down to where the upper faces meet it. No picture gives the neck: the side pictures show the upper face's light band up to the openings' tops, 4 px at 34 px/in. A Picatinny rail leaves room under its head for an accessory's jaws, and the clamps on file reach 0.40 below the rail's top beside the head (Aimpoint's Micro T-2 and Duty RDS mounts, EOTECH's G33: app/tests/rail-clamps.test.ts, 2026-10-28, which found their feet in the faces when they ran straight up to the underside)."},"rail_slots":{"label":"Slots in its top rail","kind":"count","measurements":[{"id":"photo","value":37,"unit":"count","source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 6bf562718703 (the builder set's right side seen level, 800 x 600)","scaleRef":"none: a count","method":"37 see-through slots between the seam with the receiver and its front end, every one 13.1 to 13.5 px from the next (side.py); the left side's fit, which began at the sixth, has 32 to the same front end","via":"harvest"}}]},"rail_slot0_from_rear_face":{"label":"Its rail's rearmost slot's middle ahead of its rear face","kind":"length","measurements":[{"id":"photo-right","value":0.35,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 6bf562718703 (the builder set's right side seen level, 800 x 600)","scaleRef":"its own rail's 37 slots, fitted (side.py)","method":"the seam (column 271.6) 0.350 in behind the rearmost slot's middle","via":"harvest"}},{"id":"photo-left","value":0.34,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 0627ae73f200 (the builder set's left side seen level, 800 x 600)","scaleRef":"its own rail, fitted from its sixth slot (side.py)","method":"the seam 2.307 behind the sixth slot, five pitches: 0.337","via":"harvest"}}],"adopt":{"from":"photo-right","reason":"The picture the outline is traced from."}},"mlok_slots":{"label":"M-LOK slots in each row","kind":"count","measurements":[{"id":"photo","value":7,"unit":"count","source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 6bf562718703 and 0627ae73f200 (the builder set's two sides seen level, 800 x 600)","scaleRef":"none: a count","method":"seven see-through slots in the row at the bore's level between the two round sockets, on each picture (side.py)","via":"harvest"}}],"note":"Seven in each side face's row on both pictures. The bottom's row (6 o'clock) isn't in any picture on file and is taken to be the same seven at the same places."},"mlok_slot0_from_rear_face":{"label":"Its rearmost M-LOK slot's middle ahead of its rear face","kind":"length","measurements":[{"id":"photo-right","value":3.51,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 6bf562718703 (the builder set's right side seen level, 800 x 600)","scaleRef":"its own rail's 37 slots, fitted (side.py); the slots' own middles are 1.571 in apart on it, the standard's 1.5748 (std.mlok.slot_pitch) within 0.3%","method":"the seven slots' see-through middles less the standard's pitch from each: 3.162 in ahead of the rail's rearmost slot (3.152 to 3.178), and that 0.350 ahead of the rear face","via":"harvest"}},{"id":"photo-left","value":3.49,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 0627ae73f200 (the builder set's left side seen level, 800 x 600)","scaleRef":"its own rail, fitted from its sixth slot (side.py)","method":"as the right side's: 3.157 ahead of the rearmost rail slot (3.147 to 3.180), that 0.337 ahead of the rear face","via":"harvest"}}],"adopt":{"from":"photo-right","reason":"The picture the outline is traced from; the two sides' rows are at the same places within 0.02 in."}},"window_count":{"label":"Openings in each upper face (between the side flat and the rail)","kind":"count","measurements":[{"id":"photo","value":18,"unit":"count","source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 6bf562718703 and 0627ae73f200 (the builder set's two sides seen level, 800 x 600)","scaleRef":"none: a count","method":"18 see-through openings in the row under the rail on each picture (side.py)","via":"harvest"}}]},"window0_from_rear_face":{"label":"The rearmost upper opening's middle (at the row's mid-height) ahead of its rear face","kind":"length","measurements":[{"id":"photo-right","value":2.82,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 6bf562718703 (the builder set's right side seen level, 800 x 600)","scaleRef":"its own rail's 37 slots, fitted (side.py)","method":"row 236 (mid-height of the row): the first opening's see-through middle 2.472 ahead of the rearmost rail slot, that 0.350 ahead of the rear face","via":"harvest"}},{"id":"photo-left","value":2.8,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 0627ae73f200 (the builder set's left side seen level, 800 x 600)","scaleRef":"its own rail, fitted from its sixth slot (side.py)","method":"row 239: 0.494 ahead of the sixth slot, 2.464 ahead of the rearmost, that 0.337 ahead of the rear face","via":"harvest"}}],"adopt":{"from":"photo-right","reason":"The picture the outline is traced from."}},"window_pitch":{"label":"The upper openings' pitch","kind":"length","measurements":[{"id":"photo-right","value":0.688,"unit":"in","pm":0.003,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 6bf562718703 (the builder set's right side seen level, 800 x 600)","scaleRef":"its own rail's 37 slots, fitted (side.py)","method":"the first and the 18th openings' middles 11.700 in apart over 17","via":"harvest"}},{"id":"photo-left","value":0.689,"unit":"in","pm":0.003,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 0627ae73f200 (the builder set's left side seen level, 800 x 600)","scaleRef":"its own rail, fitted from its sixth slot (side.py)","method":"11.706 in over 17","via":"harvest"}}],"adopt":{"from":"photo-right","reason":"The picture the outline is traced from; the two agree within their ±."}},"window_length":{"label":"An upper opening's length along the handguard, at the row's mid-height","kind":"length","measurements":[{"id":"photo","value":0.55,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 6bf562718703 (the builder set's right side seen level, 800 x 600)","scaleRef":"its own rail's 37 slots, fitted (side.py)","method":"row 236: the openings over the lens's foot (the widest rail slots, column 481) see through 0.55 to 0.57 in, those at the ends 0.42 to 0.51","via":"harvest"}}],"note":"Read where the lens stood over it, so that the far wall's opening, which the see-through also passes, stands in line with the near one."},"window_slant":{"label":"An upper opening's ends' lean from the upright, its top forward (seen from the side)","kind":"angle","measurements":[{"id":"photo","value":30,"unit":"deg","pm":3,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 6bf562718703 (the builder set's right side seen level, 800 x 600)","scaleRef":"its own rail's 37 slots, fitted (side.py)","method":"five openings over the lens's foot read at rows 229 and 244 (0.443 in apart): their middles 0.25 in further forward at the top: 0.57 in an inch, 30 degrees","via":"harvest"}}]},"window_bottom_above_bore":{"label":"The upper openings' lower ends above the bore axis","kind":"length","measurements":[{"id":"photo-right","value":0.39,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 6bf562718703 (the builder set's right side seen level, 800 x 600)","scaleRef":"33.86 px/in","method":"the row goes solid at row 246.5, 13.25 px above the M-LOK row's middle (side.py)","via":"harvest"}},{"id":"photo-left","value":0.39,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 0627ae73f200 (the builder set's left side seen level, 800 x 600)","scaleRef":"33.58 px/in","method":"row 248.5 against 261.5: 0.387","via":"harvest"}}],"adopt":{"from":"photo-right","reason":"Both read 0.39."}},"lower_count":{"label":"Openings in each lower face (between the side flat and the bottom)","kind":"count","measurements":[{"id":"photo","value":18,"unit":"count","source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 6bf562718703 and 0627ae73f200 (the builder set's two sides seen level, 800 x 600)","scaleRef":"none: a count","method":"18 see-through openings in the row under the M-LOK row on each picture (side.py)","via":"harvest"}}]},"lower0_from_rear_face":{"label":"The rearmost lower opening's middle (at its mid-height) ahead of its rear face","kind":"length","measurements":[{"id":"photo-right","value":2.05,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 6bf562718703 (the builder set's right side seen level, 800 x 600)","scaleRef":"its own rail's 37 slots, fitted (side.py)","method":"row 278: 1.703 ahead of the rearmost rail slot, that 0.350 ahead of the rear face","via":"harvest"}},{"id":"photo-left","value":2.05,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 0627ae73f200 (the builder set's left side seen level, 800 x 600)","scaleRef":"its own rail, fitted from its sixth slot (side.py)","method":"row 279: 0.254 behind the sixth slot, 1.716 ahead of the rearmost, that 0.337 ahead of the rear face","via":"harvest"}}],"adopt":{"from":"photo-right","reason":"Both read 2.053."}},"lower_pitch":{"label":"The lower openings' pitch","kind":"length","measurements":[{"id":"photo","value":0.689,"unit":"in","pm":0.003,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 6bf562718703 and 0627ae73f200 (the builder set's two sides seen level, 800 x 600)","scaleRef":"each picture's own rail, fitted (side.py)","method":"the first and the 18th openings' middles 11.707 and 11.702 in apart over 17: the upper row's pitch","via":"harvest"}}]},"lower_length":{"label":"A lower opening's length along the handguard, at its mid-height","kind":"length","measurements":[{"id":"photo","value":0.52,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 6bf562718703 (the builder set's right side seen level, 800 x 600)","scaleRef":"its own rail's 37 slots, fitted (side.py)","method":"rows 275 to 280, the openings over the lens's foot: 0.49 to 0.55 in see-through","via":"harvest"}}]},"lower_slant":{"label":"A lower opening's ends' lean from the upright, its top forward (seen from the side)","kind":"angle","measurements":[{"id":"photo","value":24,"unit":"deg","pm":5,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 6bf562718703 (the builder set's right side seen level, 800 x 600)","scaleRef":"its own rail's 37 slots, fitted (side.py)","method":"five openings over the lens's foot read at rows 275 and 280 (0.148 in apart): their middles 0.065 in further forward at the top: 0.44 in an inch, 24 degrees","via":"harvest"}}]},"lower_bottom_below_bore":{"label":"The lower openings' lower ends below the bore axis (seen from the side)","kind":"length","measurements":[{"id":"photo-right","value":0.67,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 6bf562718703 (the builder set's right side seen level, 800 x 600)","scaleRef":"33.86 px/in","method":"the row goes solid at row 282.5 (side.py)","via":"harvest"}},{"id":"photo-left","value":0.655,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 0627ae73f200 (the builder set's left side seen level, 800 x 600)","scaleRef":"33.58 px/in","method":"row 283.5 against 261.5","via":"harvest"}}],"adopt":{"from":"photo-right","reason":"The picture the outline is traced from."}},"qd_diameter":{"label":"Its QD sockets' holes across","kind":"length","measurements":[{"id":"photo","value":0.37,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 6bf562718703 and 0627ae73f200 (the builder set's two sides seen level, 800 x 600)","scaleRef":"33.9 px/in","method":"the rear sockets' rims, 12 to 13 px across on both pictures and the front one's on the right, looked at at 5x and 8x","via":"harvest"}}],"note":"MAS: \"Quick Detach Mounts are built into the handguard at the front and rear positions.\" Each is a round hole in the side flat at the bore's level, on both sides."},"qd_rear_from_rear_face":{"label":"The rear QD socket's middle ahead of its rear face","kind":"length","measurements":[{"id":"photo-right","value":2.27,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 6bf562718703 (the builder set's right side seen level, 800 x 600)","scaleRef":"its own rail's 37 slots, fitted (side.py)","method":"the rim's middle (column 347.5, at 5x) 1.922 ahead of the rearmost rail slot, that 0.350 ahead of the rear face","via":"harvest"}}]},"qd_front_from_rear_face":{"label":"The front QD socket's middle ahead of its rear face","kind":"length","measurements":[{"id":"photo-right","value":14.3,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 6bf562718703 (the builder set's right side seen level, 800 x 600)","scaleRef":"its own rail's 37 slots, fitted (side.py)","method":"the rim's middle (column 755.5, at 5x) 13.952 ahead of the rearmost rail slot, that 0.350 ahead of the rear face","via":"harvest"}}]},"lug_bottom_below_bore":{"label":"The clamp's lug under its rear end: its bottom below the bore axis","kind":"length","measurements":[{"id":"photo","value":1.08,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 6bf562718703 (the builder set's right side seen level, 800 x 600)","scaleRef":"33.86 px/in","method":"the silhouette's bottom under the rear end (row 296.5) below the M-LOK row's middle (side.py)","via":"harvest"}}],"note":"Its two screws cross the lug (MAS: \"The (2) handguard screws should be torqued evenly to 40 INCH LBS\"); a buyer on the page: \"Holes should be recessed, but instead, screws are sticking out.\""},"lug_flat_end_from_rear_face":{"label":"Where the lug's flat bottom ends, ahead of its rear face","kind":"length","measurements":[{"id":"photo","value":1.18,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 6bf562718703 (the builder set's right side seen level, 800 x 600)","scaleRef":"its own rail's 37 slots, fitted (side.py)","method":"the bottom at row 296 to column 311, as the fitted rail reads it","via":"harvest"}}]},"lug_end_from_rear_face":{"label":"Where the lug's sloped front meets the bottom flat, ahead of its rear face","kind":"length","measurements":[{"id":"photo","value":1.48,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 6bf562718703 (the builder set's right side seen level, 800 x 600)","scaleRef":"its own rail's 37 slots, fitted (side.py)","method":"the bottom rises to the flat's row 288 at column 321","via":"harvest"}}]},"screw0_from_rear_face":{"label":"The clamp's rear screw ahead of its rear face","kind":"length","measurements":[{"id":"photo-right","value":0.34,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 6bf562718703 (the builder set's right side seen level, 800 x 600)","scaleRef":"its own rail's 37 slots, fitted (side.py)","method":"the screw's end (column 283, 8x) 0.008 behind the rearmost rail slot","via":"harvest"}},{"id":"photo-left","value":0.37,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 0627ae73f200 (the builder set's left side seen level, 800 x 600)","scaleRef":"its own rail, fitted from its sixth slot (side.py)","method":"the screw's head (column 286 mirrored, 8x)","via":"harvest"}}],"adopt":{"from":"photo-right","reason":"The picture the outline is traced from."}},"screw_spacing":{"label":"The clamp's two screws apart","kind":"length","measurements":[{"id":"photo","value":0.6,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 6bf562718703 and 0627ae73f200 (the builder set's two sides seen level, 800 x 600)","scaleRef":"each picture's own rail, fitted (side.py)","method":"0.599 on the right (columns 283 and 303), 0.607 on the left","via":"harvest"}}]},"screw_below_bore":{"label":"The clamp's screws below the bore axis","kind":"length","measurements":[{"id":"photo","value":0.93,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 6bf562718703 and 0627ae73f200 (the builder set's two sides seen level, 800 x 600)","scaleRef":"33.86 and 33.58 px/in","method":"their middles at rows 291.25 and 292.5 (8x): 0.93 and 0.92 below each M-LOK row's middle","via":"harvest"}}]},"screw_head_diameter":{"label":"A clamp screw's head across (on its left side)","kind":"length","measurements":[{"id":"photo","value":0.26,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 0627ae73f200 (the builder set's left side seen level, 800 x 600)","scaleRef":"33.58 px/in","method":"the two round heads standing on the lug's left face, about 8.75 px across (8x)","via":"harvest"}}]},"screw_end_diameter":{"label":"A clamp screw's end across (on its right side)","kind":"length","measurements":[{"id":"photo","value":0.2,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/mas-defense-nero-15-handguard 6bf562718703 (the builder set's right side seen level, 800 x 600)","scaleRef":"33.86 px/in","method":"the two smaller rounds on the lug's right face, about 6.9 px across (8x)","via":"harvest"}}]},"screw_head_proud":{"label":"How far a clamp screw's head stands off the lug's left face","kind":"length","measurements":[{"id":"assumed","value":0.06,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the level side pictures see the heads face on, and the picture from the front right sees the lug's right face, where the screws' ends are.","via":"harvest"}}],"note":"A buyer on its page: \"Holes should be recessed, but instead, screws are sticking out.\""},"nut_across_flats":{"label":"Its barrel nut's wrench flats across (the nut isn't drawn: it is inside its rear end)","kind":"length","measurements":[{"id":"mas","value":1.1875,"unit":"in","pm":0.005,"stated":"The barrel nut will accept a 1 3/16\" or (30mm) wrench or crow foot.","source":{"type":"spec","publisher":"manufacturer","name":"MAS Defense, MAS DEFENSE 15\" NERO M-LOK FREE FLOAT - STEALTH GRAY (MAS00106384), description","url":"https://www.masdefense.com/MAS00106384-p/mas00106384.htm","retrieved":"2026-10-28","via":"harvest"}}]},"reach_inside":{"label":"Room inside an M-LOK face for an accessory's nuts (from the face in to what runs under it)","kind":"length","measurements":[],"note":"Depends on the barrel and the gas block under it, other parts: no figure."}}},{"subject":"mas-defense-nero-9-87-handguard","title":"MAS Defense 9.87\" NERO M-LOK FREE FLOAT (Stealth Gray MAS00106378)","dimensions":{"weight":{"label":"Weight with its steel barrel nut and two screws","kind":"mass","measurements":[{"id":"mas","value":10.6,"unit":"oz","pm":0.05,"stated":"The rail, steel barrel nut and attaching screws brings the weight to 10.6oz.","source":{"type":"spec","publisher":"manufacturer","name":"MAS Defense, MAS DEFENSE 9.87\" NERO M-LOK FREE FLOAT - STEALTH GRAY (MAS00106378), description","url":"https://www.masdefense.com/MAS00106375-p/mas00106378.htm","retrieved":"2026-10-28","via":"harvest"}}],"note":"What goes on the rifle: MAS sells it with its own steel barrel nut and its two screws. Every colour's page says 7.2 and 10.6 oz."},"rail_weight":{"label":"Weight of the handguard alone (without its barrel nut and screws)","kind":"mass","measurements":[{"id":"mas","value":7.2,"unit":"oz","pm":0.05,"stated":"Weight comes in at 7.2oz for the rail itself.","source":{"type":"spec","publisher":"manufacturer","name":"MAS Defense, MAS DEFENSE 9.87\" NERO M-LOK FREE FLOAT - STEALTH GRAY (MAS00106378), description","url":"https://www.masdefense.com/MAS00106375-p/mas00106378.htm","retrieved":"2026-10-28","via":"harvest"}}]},"length":{"label":"Length (its rear face to its rail's front end)","kind":"length","measurements":[{"id":"mas","value":9.87,"unit":"in","pm":0.005,"stated":"MAS DEFENSE 9.87\" NERO M-LOK FREE FLOAT - STEALTH GRAY","source":{"type":"spec","publisher":"manufacturer","name":"MAS Defense, the page's title (MAS00106378)","url":"https://www.masdefense.com/MAS00106375-p/mas00106378.htm","retrieved":"2026-10-28","via":"harvest"}},{"id":"photo-rail","value":10.01,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/mas-defense-nero-9-87-handguard 499981fc28ce (MAS Defense's picture of the 9.87 in in black, MAS00106308-2: from the front right and above, the pose every colour's picture has, 800 x 600)","scaleRef":"its own rail's slots on this picture, turned level (33.73 degrees): 21.96 px a pitch, 55.74 px/in (std.picatinny.slot_pitch)","method":"its 24 rail slots counted, their pitch times 23, with the land behind the rearmost slot (18 px to where the silhouette begins on the rail's row) and ahead of the foremost (26 px) each brought onto the part by the 15 in's same row: 10.01 in","via":"harvest"}},{"id":"photo-extent","value":9.97,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/mas-defense-nero-9-87-handguard 499981fc28ce (MAS Defense's picture of the 9.87 in in black, MAS00106308-2: from the front right and above, the pose every colour's picture has, 800 x 600)","scaleRef":"its own rail's slots on this picture, turned level (33.73 degrees): 21.96 px a pitch, 55.74 px/in (std.picatinny.slot_pitch)","method":"the silhouette's length on the upper openings' row (550 px) brought onto the part by the 15 in's same row (whose level pictures read 15.12): 9.97 in","via":"harvest"}},{"id":"photo-plan","value":10.01,"unit":"in","pm":0.1,"source":{"type":"photo","photo":"references/mas-defense-nero-9-87-handguard e83bcb86bd83 (MAS Defense's render of this length in FDE from above, beside its nut, 800 x 600)","scaleRef":"the 15 in's render of the same view (fb9e410b47d4): its silhouette 871.6 px for its 15.12 in, taken to be drawn at the same scale","method":"this one's silhouette 576.8 px end to end, its axis found as the turn that makes it narrowest (34.2, 34.4 degrees) along its axis (ends.py): a check, the renders' scale being taken as one","via":"harvest"}}],"adopt":{"from":"photo-rail","reason":"Its rail's slots counted between lands the picture shows as the 15 in's; the silhouette's length on another row reads within the ±; the title's figure stays beside it: the model's places along it are the picture's."},"note":"MAS names it 9.87 in (its title) and \"Specter Length\"; the picture puts its rail's front end 10.01 in ahead of its rear face, 0.14 in more than the title's figure. The 15 in's title is 0.12 in short of its pictures the same way."},"inside_diameter":{"label":"Inside diameter","kind":"length","measurements":[{"id":"mas","value":1.25,"unit":"in","pm":0.005,"stated":"The slim 1.25\" inner diameter will require a slim muzzle device.","source":{"type":"spec","publisher":"manufacturer","name":"MAS Defense, MAS DEFENSE 9.87\" NERO M-LOK FREE FLOAT - STEALTH GRAY (MAS00106378), description","url":"https://www.masdefense.com/MAS00106375-p/mas00106378.htm","retrieved":"2026-10-28","via":"harvest"}}],"note":"MAS: it \"will require a slim muzzle device\" (one that passes through 1.25 in)."},"rear_x":{"label":"Its rear face ahead of the receiver's front face","kind":"length","measurements":[{"id":"family","value":-0.445,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.rear_x}","via":"harvest"}}],"note":"No picture of this length on an upper is level enough to read; taken as the 15 in's, whose rear face bears on the receiver's shoulder (where the barrel-nut thread begins) in its level pictures (MAS: \"The monolithic top rail of the handguard sits directly against the upper receiver rail\")."},"width":{"label":"Width across its side flats (the M-LOK faces at 3 and 9 o'clock)","kind":"length","measurements":[{"id":"family","value":1.6,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.width}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"rail_top_above_bore":{"label":"Its rail's top above the bore axis","kind":"length","measurements":[{"id":"family","value":1.22,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.rail_top_above_bore}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"bottom_below_bore":{"label":"Its bottom flat below the bore axis","kind":"length","measurements":[{"id":"family","value":0.85,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.bottom_below_bore}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"side_flat_top_above_bore":{"label":"The side flat's upper edge above the bore axis","kind":"length","measurements":[{"id":"family","value":0.62,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.side_flat_top_above_bore}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"side_flat_bottom_below_bore":{"label":"The side flat's lower edge below the bore axis","kind":"length","measurements":[{"id":"family","value":0.4,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.side_flat_bottom_below_bore}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"bottom_half_width":{"label":"Half the bottom flat's width","kind":"length","measurements":[{"id":"family","value":0.35,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.bottom_half_width}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"wall":{"label":"Its wall's thickness from the clamp's ring forward","kind":"length","measurements":[{"id":"family","value":0.06,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.wall}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"rail_underside_below_top":{"label":"Its rail's underside below the rail's top","kind":"length","measurements":[{"id":"family","value":0.24,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.rail_underside_below_top}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"rail_neck_below_top":{"label":"Where its upper faces meet the neck under its rail's head, below the rail's top","kind":"length","measurements":[{"id":"family","value":0.4,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.rail_neck_below_top}","via":"harvest"},"note":"The NERO's one section, as the 15 in's (an assumption there: as deep as a Picatinny clamp's jaws need)."}]},"window_length":{"label":"An upper opening's length along it, at the row's mid-height","kind":"length","measurements":[{"id":"family","value":0.55,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.window_length}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"window_bottom_above_bore":{"label":"The upper openings' lower ends above the bore axis","kind":"length","measurements":[{"id":"family","value":0.39,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.window_bottom_above_bore}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"lower_length":{"label":"A lower opening's length along it, at its mid-height","kind":"length","measurements":[{"id":"family","value":0.52,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.lower_length}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"lower_bottom_below_bore":{"label":"The lower openings' lower ends below the bore axis","kind":"length","measurements":[{"id":"family","value":0.67,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.lower_bottom_below_bore}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"qd_diameter":{"label":"Its QD sockets' holes across","kind":"length","measurements":[{"id":"family","value":0.37,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.qd_diameter}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"lug_bottom_below_bore":{"label":"The clamp's lug: its bottom below the bore axis","kind":"length","measurements":[{"id":"family","value":1.08,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.lug_bottom_below_bore}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"lug_flat_end_from_rear_face":{"label":"Where the lug's flat bottom ends, ahead of its rear face","kind":"length","measurements":[{"id":"family","value":1.18,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.lug_flat_end_from_rear_face}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"lug_end_from_rear_face":{"label":"Where the lug's sloped front meets the bottom flat","kind":"length","measurements":[{"id":"family","value":1.48,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.lug_end_from_rear_face}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"screw0_from_rear_face":{"label":"The clamp's rear screw ahead of its rear face","kind":"length","measurements":[{"id":"family","value":0.34,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.screw0_from_rear_face}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"screw_spacing":{"label":"The clamp's two screws apart","kind":"length","measurements":[{"id":"family","value":0.6,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.screw_spacing}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"screw_below_bore":{"label":"The clamp's screws below the bore axis","kind":"length","measurements":[{"id":"family","value":0.93,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.screw_below_bore}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"screw_head_diameter":{"label":"A clamp screw's head across","kind":"length","measurements":[{"id":"family","value":0.26,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.screw_head_diameter}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"screw_end_diameter":{"label":"A clamp screw's end across","kind":"length","measurements":[{"id":"family","value":0.2,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.screw_end_diameter}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"screw_head_proud":{"label":"How far a clamp screw's head stands off the lug","kind":"length","measurements":[{"id":"family","value":0.06,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.screw_head_proud}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"nut_across_flats":{"label":"Its barrel nut's wrench flats across","kind":"length","measurements":[{"id":"family","value":1.1875,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.nut_across_flats}","via":"harvest"},"note":"The NERO's one section, as the 15 in's level side pictures give it: this length's own picture of MAS's same pose has its rows of openings, its M-LOK row and its silhouette at the same heights as the 15 in's within a pixel (rotated level, rows 428 to 460, 474 to 488 and 502 to 518 on all three)."}]},"height":{"label":"Height (its rail's top to its bottom flat)","kind":"length","measurements":[{"id":"derived","value":2.07,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{.rail_top_above_bore} + {.bottom_below_bore}","via":"harvest"}}]},"face_distance":{"label":"Its M-LOK faces' distance from the bore axis (one figure for all three)","kind":"length","measurements":[{"id":"derived","value":0.8,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.width} / 2","via":"harvest"}}]},"window_slant":{"label":"An upper opening's ends' lean from the upright, its top forward (seen from the side)","kind":"angle","measurements":[{"id":"family","value":30,"unit":"deg","pm":3,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.window_slant}","via":"harvest"},"note":"The 15 in's, read on its level picture: this length's picture of the same pose shows its openings at the same lean."}]},"lower_slant":{"label":"A lower opening's ends' lean from the upright, its top forward (seen from the side)","kind":"angle","measurements":[{"id":"family","value":24,"unit":"deg","pm":5,"source":{"type":"derived","expr":"{mas-defense-nero-15-handguard.lower_slant}","via":"harvest"},"note":"The 15 in's, read on its level picture: this length's picture of the same pose shows its openings at the same lean."}]},"rail_slots":{"label":"Slots in its top rail","kind":"count","measurements":[{"id":"photo","value":24,"unit":"count","source":{"type":"photo","photo":"references/mas-defense-nero-9-87-handguard 499981fc28ce (MAS Defense's picture of the 9.87 in in black, MAS00106308-2: from the front right and above, the pose every colour's picture has, 800 x 600)","scaleRef":"none: a count","method":"24 see-through slots along the rail's row on the picture turned level, every one 21.96 px from the next, from just ahead of the rear end to just behind the front (q3.py)","via":"harvest"}}]},"mlok_slots":{"label":"M-LOK slots in each row","kind":"count","measurements":[{"id":"photo","value":4,"unit":"count","source":{"type":"photo","photo":"references/mas-defense-nero-9-87-handguard 499981fc28ce (MAS Defense's picture of the 9.87 in in black, MAS00106308-2: from the front right and above, the pose every colour's picture has, 800 x 600)","scaleRef":"none: a count","method":"4 slots in the row at the bore's level, between the round sockets (q.py)","via":"harvest"}}],"note":"Counted in the right side's row on this picture; the left's and the bottom's aren't in any picture of this length and are taken to be the same."},"window_count":{"label":"Openings in each upper face","kind":"count","measurements":[{"id":"photo","value":10,"unit":"count","source":{"type":"photo","photo":"references/mas-defense-nero-9-87-handguard 499981fc28ce (MAS Defense's picture of the 9.87 in in black, MAS00106308-2: from the front right and above, the pose every colour's picture has, 800 x 600)","scaleRef":"none: a count","method":"10 see-through openings in the row under the rail (q.py)","via":"harvest"}}]},"lower_count":{"label":"Openings in each lower face","kind":"count","measurements":[{"id":"photo","value":10,"unit":"count","source":{"type":"photo","photo":"references/mas-defense-nero-9-87-handguard 499981fc28ce (MAS Defense's picture of the 9.87 in in black, MAS00106308-2: from the front right and above, the pose every colour's picture has, 800 x 600)","scaleRef":"none: a count","method":"10 see-through openings in the row under the M-LOK row (q.py)","via":"harvest"}}]},"rail_slot0_from_rear_face":{"label":"Its rail's rearmost slot's middle ahead of its rear face","kind":"length","measurements":[{"id":"photo","value":0.36,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/mas-defense-nero-9-87-handguard 499981fc28ce (MAS Defense's picture of the 9.87 in in black, MAS00106308-2: from the front right and above, the pose every colour's picture has, 800 x 600)","scaleRef":"its own rail's slots on this picture, turned level (33.73 degrees): 21.96 px a pitch, 55.74 px/in (std.picatinny.slot_pitch)","method":"the rearmost slot 18 px ahead of where the silhouette begins on the rail's row; each row read from where the silhouette begins on that row, and brought onto the part by that row's offset on the 15 in's picture of the same pose (MAS00106314-2: the same turn within 0.2 degrees), whose figures are read on its level side pictures (mas-defense-nero-15-handguard) (+0.032 in on this row)","via":"harvest"}}]},"mlok_slot0_from_rear_face":{"label":"Its rearmost M-LOK slot's middle ahead of its rear face","kind":"length","measurements":[{"id":"photo","value":3.89,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/mas-defense-nero-9-87-handguard 499981fc28ce (MAS Defense's picture of the 9.87 in in black, MAS00106308-2: from the front right and above, the pose every colour's picture has, 800 x 600)","scaleRef":"its own rail's slots on this picture, turned level (33.73 degrees): 21.96 px a pitch, 55.74 px/in (std.picatinny.slot_pitch)","method":"the first slot's see-through middle 224 px ahead of where the silhouette begins on the M-LOK row; each row read from where the silhouette begins on that row, and brought onto the part by that row's offset on the 15 in's picture of the same pose (MAS00106314-2: the same turn within 0.2 degrees), whose figures are read on its level side pictures (mas-defense-nero-15-handguard) (-0.124 in on this row)","via":"harvest"}}]},"window0_from_rear_face":{"label":"The rearmost upper opening's middle (at the row's mid-height) ahead of its rear face","kind":"length","measurements":[{"id":"photo","value":3.21,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/mas-defense-nero-9-87-handguard 499981fc28ce (MAS Defense's picture of the 9.87 in in black, MAS00106308-2: from the front right and above, the pose every colour's picture has, 800 x 600)","scaleRef":"its own rail's slots on this picture, turned level (33.73 degrees): 21.96 px a pitch, 55.74 px/in (std.picatinny.slot_pitch)","method":"the first opening's middle 179 px ahead of where the silhouette begins on its row's mid-height; each row read from where the silhouette begins on that row, and brought onto the part by that row's offset on the 15 in's picture of the same pose (MAS00106314-2: the same turn within 0.2 degrees), whose figures are read on its level side pictures (mas-defense-nero-15-handguard) (-0.003 in on this row)","via":"harvest"}}]},"window_pitch":{"label":"The upper openings' pitch","kind":"length","measurements":[{"id":"photo","value":0.68,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/mas-defense-nero-9-87-handguard 499981fc28ce (MAS Defense's picture of the 9.87 in in black, MAS00106308-2: from the front right and above, the pose every colour's picture has, 800 x 600)","scaleRef":"its own rail's slots on this picture, turned level (33.73 degrees): 21.96 px a pitch, 55.74 px/in (std.picatinny.slot_pitch)","method":"the first and last openings' middles 341 px apart over 9","via":"harvest"}}]},"lower0_from_rear_face":{"label":"The rearmost lower opening's middle (at its mid-height) ahead of its rear face","kind":"length","measurements":[{"id":"photo","value":2.41,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/mas-defense-nero-9-87-handguard 499981fc28ce (MAS Defense's picture of the 9.87 in in black, MAS00106308-2: from the front right and above, the pose every colour's picture has, 800 x 600)","scaleRef":"its own rail's slots on this picture, turned level (33.73 degrees): 21.96 px a pitch, 55.74 px/in (std.picatinny.slot_pitch)","method":"the first opening's middle 139 px ahead of where the silhouette begins on its row; each row read from where the silhouette begins on that row, and brought onto the part by that row's offset on the 15 in's picture of the same pose (MAS00106314-2: the same turn within 0.2 degrees), whose figures are read on its level side pictures (mas-defense-nero-15-handguard) (-0.085 in on this row)","via":"harvest"}}]},"lower_pitch":{"label":"The lower openings' pitch","kind":"length","measurements":[{"id":"photo","value":0.682,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/mas-defense-nero-9-87-handguard 499981fc28ce (MAS Defense's picture of the 9.87 in in black, MAS00106308-2: from the front right and above, the pose every colour's picture has, 800 x 600)","scaleRef":"its own rail's slots on this picture, turned level (33.73 degrees): 21.96 px a pitch, 55.74 px/in (std.picatinny.slot_pitch)","method":"the first and last openings' middles 342 px apart over 9","via":"harvest"}}]},"qd_rear_from_rear_face":{"label":"The rear QD socket's middle ahead of its rear face","kind":"length","measurements":[{"id":"photo","value":2.69,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/mas-defense-nero-9-87-handguard 499981fc28ce (MAS Defense's picture of the 9.87 in in black, MAS00106308-2: from the front right and above, the pose every colour's picture has, 800 x 600)","scaleRef":"its own rail's slots on this picture, turned level (33.73 degrees): 21.96 px a pitch, 55.74 px/in (std.picatinny.slot_pitch)","method":"the socket's see-through middle 160 px ahead of where the silhouette begins on the M-LOK row; each row read from where the silhouette begins on that row, and brought onto the part by that row's offset on the 15 in's picture of the same pose (MAS00106314-2: the same turn within 0.2 degrees), whose figures are read on its level side pictures (mas-defense-nero-15-handguard) (-0.182 in for a socket on this row)","via":"harvest"}}]},"reach_inside":{"label":"Room inside an M-LOK face for an accessory's nuts (from the face in to what runs under it)","kind":"length","measurements":[],"note":"Depends on the barrel and the gas block under it, other parts: no figure."}}},{"subject":"mft-battlelink-minimalist-stock","title":"Mission First Tactical BATTLELINK Minimalist Milspec Stock","dimensions":{"length":{"label":"Overall length","kind":"length","measurements":[{"id":"mft","value":7.084,"unit":"in","stated":"Length: 7.084\"","source":{"type":"spec","publisher":"manufacturer","name":"Mission First Tactical, BATTLELINK Minimalist Milspec Stock (SKU: BMSMIL; the description's last lines)","url":"https://missionfirsttactical.com/BMSMIL","retrieved":"2026-10-13","via":"harvest"}},{"id":"wing","value":7.06,"unit":"in","stated":"Length: 7.06\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Mission First Tactical BattleLink Minimalist Stock (Mil-Spec) (MPN: BMSMIL; Specifications)","url":"https://www.wingtactical.com/firearm-parts/ar-15/stocks-accessories/mission-first-tactical-battlelink-minimalist-stock-mil-spec/","retrieved":"2026-10-13","via":"harvest"},"note":"The shop's own figure, with its own photographs: it differs from the maker's in all four."},{"id":"primary-arms","value":7.084,"unit":"in","stated":"5.22\" height, 1.752\" width, 7.084\" length","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Mission First Tactical Battlelink Minimalist Collapsible AR-15 Stock - Carbine (SKU: MFTBMSMILBLK, MPN: BMSMIL)","url":"https://www.primaryarms.com/mission-first-tactical-battlelink-minimalist-stock-mil-spec-black","retrieved":"2026-10-13","via":"harvest"}},{"id":"kygunco","value":7.084,"unit":"in","stated":"Length: 7.084\"","source":{"type":"spec","publisher":"retailer","name":"KYGUNCO, Mission First Tactical BATTLELINK Minimalist Milspec Stock Black (Item # 66353, UPC 676315025856)","url":"https://kygunco.com/product/mft-bmsmil-battlelink-minimalist-milspec-stock-black","retrieved":"2026-10-13","via":"harvest"}},{"id":"ar15discounts","value":7.084,"unit":"in","stated":"Length: 7.084″","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, MFT BATTLELINK Minimalist Stock - Mil Spec - Black - OEM (MPN BMSMIL)","url":"https://ar15discounts.com/products/mft-battlelink-minimalist-stock-mil-spec-black-oem/","retrieved":"2026-10-13","via":"harvest"}},{"id":"redcon1","value":7.084,"unit":"in","stated":"Length: 7.084\"","source":{"type":"spec","publisher":"retailer","name":"Redcon1 Tactical, MFT BMS Battlelink Minimalist Stock Mil-Spec - Black (Mnf#/Vendor# BMSMIL, UPC 676315025856)","url":"https://redcon1tactical.com/mission-first-tactical-battlelink-minimalist-stock-bms-mil-spec-black.html","retrieved":"2026-10-13","via":"harvest"}},{"id":"redwolf","value":180,"unit":"mm","pm":0.05,"stated":"Length (mm) 180.0","source":{"type":"spec","publisher":"retailer","name":"RedWolf Airsoft, MFT BMSMIL - BATTLELINK Minimalist Stock - Gray (the shop's own table)","url":"https://www.redwolfairsoft.com/accessories-grips-and-stocks-aeg-mft-bmsmil-battlelink-minimalist-stock-gray.html","retrieved":"2026-10-13","via":"harvest"},"note":"An airsoft shop selling the maker's stock in gray; its table's own units (7.087 in: the maker's 7.084 to the nearest millimetre, written to a tenth)."}],"adopt":{"from":"mft","reason":"The maker's own figure; four sellers repeat it and a fifth's millimetres round to it. Wing Tactical's 7.06 is 0.3% under it, the shop's own."},"note":"From the butt pad's rearmost point to the front of the housing round the tube. Against the height it reads 1.5% long in the maker's own straight side view (1546 x 1122 px: 1.378, for 7.084 / 5.22 = 1.357); Wing Tactical's own two figures, 7.06 / 5.13 = 1.376, keep the photo's proportion to 0.15%."},"height":{"label":"Height","kind":"length","measurements":[{"id":"mft","value":5.22,"unit":"in","stated":"Height: 5.22\"","source":{"type":"spec","publisher":"manufacturer","name":"Mission First Tactical, BATTLELINK Minimalist Milspec Stock (SKU: BMSMIL; the description's last lines)","url":"https://missionfirsttactical.com/BMSMIL","retrieved":"2026-10-13","via":"harvest"}},{"id":"wing","value":5.13,"unit":"in","stated":"Height: 5.13\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Mission First Tactical BattleLink Minimalist Stock (Mil-Spec) (MPN: BMSMIL; Specifications)","url":"https://www.wingtactical.com/firearm-parts/ar-15/stocks-accessories/mission-first-tactical-battlelink-minimalist-stock-mil-spec/","retrieved":"2026-10-13","via":"harvest"}},{"id":"primary-arms","value":5.22,"unit":"in","stated":"5.22\" height, 1.752\" width, 7.084\" length","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Mission First Tactical Battlelink Minimalist Collapsible AR-15 Stock - Carbine (SKU: MFTBMSMILBLK, MPN: BMSMIL)","url":"https://www.primaryarms.com/mission-first-tactical-battlelink-minimalist-stock-mil-spec-black","retrieved":"2026-10-13","via":"harvest"}},{"id":"kygunco","value":5.22,"unit":"in","stated":"Height: 5.22\"","source":{"type":"spec","publisher":"retailer","name":"KYGUNCO, Mission First Tactical BATTLELINK Minimalist Milspec Stock Black (Item # 66353, UPC 676315025856)","url":"https://kygunco.com/product/mft-bmsmil-battlelink-minimalist-milspec-stock-black","retrieved":"2026-10-13","via":"harvest"}},{"id":"ar15discounts","value":5.22,"unit":"in","stated":"Height: 5.22″","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, MFT BATTLELINK Minimalist Stock - Mil Spec - Black - OEM (MPN BMSMIL)","url":"https://ar15discounts.com/products/mft-battlelink-minimalist-stock-mil-spec-black-oem/","retrieved":"2026-10-13","via":"harvest"}},{"id":"redcon1","value":5.22,"unit":"in","stated":"Height: 5.22\"","source":{"type":"spec","publisher":"retailer","name":"Redcon1 Tactical, MFT BMS Battlelink Minimalist Stock Mil-Spec - Black (Mnf#/Vendor# BMSMIL, UPC 676315025856)","url":"https://redcon1tactical.com/mission-first-tactical-battlelink-minimalist-stock-bms-mil-spec-black.html","retrieved":"2026-10-13","via":"harvest"}}],"adopt":{"from":"mft","reason":"The maker's own figure, which four sellers repeat. Wing Tactical's 5.13 is the shop's own and fits the maker's side photo better (5.14 at the length's scale): kept beside it, not averaged."},"note":"From the housing's top to the toe. The maker's 5.22 and Wing Tactical's 5.13 are 1.7% apart, and the maker's straight side view takes the shop's side: at the scale its length gives (218.2 px/in for 7.084) the silhouette is 5.14 in high. Both are kept; the side outline is scaled by the maker's two figures together (they fit it within 1.5%)."},"width":{"label":"Width","kind":"length","measurements":[{"id":"mft","value":1.752,"unit":"in","stated":"Width: 1.752\"","source":{"type":"spec","publisher":"manufacturer","name":"Mission First Tactical, BATTLELINK Minimalist Milspec Stock (SKU: BMSMIL; the description's last lines)","url":"https://missionfirsttactical.com/BMSMIL","retrieved":"2026-10-13","via":"harvest"}},{"id":"wing","value":1.76,"unit":"in","stated":"Width: 1.76\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Mission First Tactical BattleLink Minimalist Stock (Mil-Spec) (MPN: BMSMIL; Specifications)","url":"https://www.wingtactical.com/firearm-parts/ar-15/stocks-accessories/mission-first-tactical-battlelink-minimalist-stock-mil-spec/","retrieved":"2026-10-13","via":"harvest"}},{"id":"primary-arms","value":1.752,"unit":"in","stated":"5.22\" height, 1.752\" width, 7.084\" length","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Mission First Tactical Battlelink Minimalist Collapsible AR-15 Stock - Carbine (SKU: MFTBMSMILBLK, MPN: BMSMIL)","url":"https://www.primaryarms.com/mission-first-tactical-battlelink-minimalist-stock-mil-spec-black","retrieved":"2026-10-13","via":"harvest"}},{"id":"kygunco","value":1.752,"unit":"in","stated":"Width: 1.752\"","source":{"type":"spec","publisher":"retailer","name":"KYGUNCO, Mission First Tactical BATTLELINK Minimalist Milspec Stock Black (Item # 66353, UPC 676315025856)","url":"https://kygunco.com/product/mft-bmsmil-battlelink-minimalist-milspec-stock-black","retrieved":"2026-10-13","via":"harvest"}},{"id":"ar15discounts","value":1.752,"unit":"in","stated":"Width: 1.752″","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, MFT BATTLELINK Minimalist Stock - Mil Spec - Black - OEM (MPN BMSMIL)","url":"https://ar15discounts.com/products/mft-battlelink-minimalist-stock-mil-spec-black-oem/","retrieved":"2026-10-13","via":"harvest"}},{"id":"redcon1","value":1.752,"unit":"in","stated":"Width: 1.752\"","source":{"type":"spec","publisher":"retailer","name":"Redcon1 Tactical, MFT BMS Battlelink Minimalist Stock Mil-Spec - Black (Mnf#/Vendor# BMSMIL, UPC 676315025856)","url":"https://redcon1tactical.com/mission-first-tactical-battlelink-minimalist-stock-bms-mil-spec-black.html","retrieved":"2026-10-13","via":"harvest"}}],"adopt":{"from":"mft","reason":"The maker's own figure, which four sellers repeat; Wing Tactical's 1.76 is the same to its hundredth."},"note":"The widest place, which no view on file shows square. It is not the mouth: the housing is 1.61 in across there in Wing Tactical's straight view into it (body_width). Behind the step in its side the housing is fuller (the cheek part: the maker's 'Upper section provides enhanced cheek weld'), and that part shows beside the mouth in the same view, 1.69 ± 0.05 in across where it begins (rear_width): the published width is taken to be that part's, 1.2 of that reading's ± above it."},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"mft","value":5.8,"unit":"oz","stated":"Weight: 5.8oz","source":{"type":"spec","publisher":"manufacturer","name":"Mission First Tactical, BATTLELINK Minimalist Milspec Stock (SKU: BMSMIL; the description's last lines)","url":"https://missionfirsttactical.com/BMSMIL","retrieved":"2026-10-13","via":"harvest"}},{"id":"mft-shipping","value":10,"unit":"oz","pm":0.005,"stated":"Shipping Weight: 10.00 Ounces","source":{"type":"spec","publisher":"manufacturer","name":"Mission First Tactical, BATTLELINK Minimalist Milspec Stock (the shop's line under SKU and UPC)","url":"https://missionfirsttactical.com/BMSMIL","retrieved":"2026-10-13","via":"harvest"},"note":"The shop system's shipping weight, the stock as boxed: not the stock's."},{"id":"wing","value":6,"unit":"oz","stated":"Weight: 6 oz.","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Mission First Tactical BattleLink Minimalist Stock (Mil-Spec) (MPN: BMSMIL; Specifications)","url":"https://www.wingtactical.com/firearm-parts/ar-15/stocks-accessories/mission-first-tactical-battlelink-minimalist-stock-mil-spec/","retrieved":"2026-10-13","via":"harvest"},"note":"To the whole ounce (its bullet: 'Lightweight - Only 6 oz.!'): its ± is half an ounce as stated."},{"id":"primary-arms","value":5.8,"unit":"oz","stated":"5.8 oz weight","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Mission First Tactical Battlelink Minimalist Collapsible AR-15 Stock - Carbine (SKU: MFTBMSMILBLK, MPN: BMSMIL)","url":"https://www.primaryarms.com/mission-first-tactical-battlelink-minimalist-stock-mil-spec-black","retrieved":"2026-10-13","via":"harvest"}},{"id":"kygunco","value":5.8,"unit":"oz","stated":"Weight: 5.8oz","source":{"type":"spec","publisher":"retailer","name":"KYGUNCO, Mission First Tactical BATTLELINK Minimalist Milspec Stock Black (Item # 66353, UPC 676315025856)","url":"https://kygunco.com/product/mft-bmsmil-battlelink-minimalist-milspec-stock-black","retrieved":"2026-10-13","via":"harvest"}},{"id":"ar15discounts","value":5.8,"unit":"oz","stated":"Weight: 5.8 oz","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, MFT BATTLELINK Minimalist Stock - Mil Spec - Black - OEM (MPN BMSMIL)","url":"https://ar15discounts.com/products/mft-battlelink-minimalist-stock-mil-spec-black-oem/","retrieved":"2026-10-13","via":"harvest"}},{"id":"redcon1","value":5.8,"unit":"oz","stated":"Weight: 5.8 oz","source":{"type":"spec","publisher":"retailer","name":"Redcon1 Tactical, MFT BMS Battlelink Minimalist Stock Mil-Spec - Black (Mnf#/Vendor# BMSMIL, UPC 676315025856)","url":"https://redcon1tactical.com/mission-first-tactical-battlelink-minimalist-stock-bms-mil-spec-black.html","retrieved":"2026-10-13","via":"harvest"}},{"id":"press-release","value":5.8,"unit":"oz","stated":"the lightest butt stock of its kind ever produced at 5.8 ounces","source":{"type":"spec","publisher":"review","name":"Officer.com, Mission First Tactical Introduces the Battlelink Minimalist Stock (the maker's press release, 2013-09-24)","url":"https://www.officer.com/home/press-release/11176012/mission-first-tactical-mission-first-tactical-introduces-the-battlelink-minimalist-stock","retrieved":"2026-10-13","via":"harvest"},"note":"The stock as first sold; which tube it was for isn't said."},{"id":"recoil-scale","value":5.8,"unit":"oz","pm":0.05,"source":{"type":"photo","photo":"references/mft-battlelink-minimalist-stock ec3a5dd4f3cb (Recoil, 2013-09-24: 'MFT Battlelink Minimalist Stock on the scales', 618 x 826)","scaleRef":"none: a reading of the instrument's own display","method":"the stock lies on a Pelouze PS20DL postal scale ('Capacity 20 Lb x 0.1 oz' on its face); its display reads 00 lb 05.8 oz; ± is half its step","via":"harvest"},"note":"The one weighing on file: the 2013 stock, the tube it was made for unsaid (the maker prints one weight for both)."},{"id":"redwolf","value":0.14,"unit":"kg","stated":"Net Weight (kg) 0.14","source":{"type":"spec","publisher":"retailer","name":"RedWolf Airsoft, MFT BMSMIL - BATTLELINK Minimalist Stock - Gray (the shop's own table)","url":"https://www.redwolfairsoft.com/accessories-grips-and-stocks-aeg-mft-bmsmil-battlelink-minimalist-stock-gray.html","retrieved":"2026-10-13","via":"harvest"},"note":"4.9 oz: the airsoft shop's own table for the gray one, to the hundredth of a kilogram."}],"adopt":{"from":"mft","reason":"The maker's own figure, repeated by four sellers and its 2013 release, and read once on a scale (Recoil's photo: 05.8 oz). The 10 oz beside it is the boxed stock's shipping weight, Wing Tactical's 6 a rounding, the airsoft shop's 0.14 kg its own."},"note":"5.8 oz in the maker's words since its 2013 release, and once on a scale: Recoil's photo of the stock on a Pelouze postal scale (0.1 oz steps) reads 05.8 oz. The maker's page also carries its shop's shipping weight (10 oz, the stock as boxed), Wing Tactical rounds to 6 oz and an airsoft shop's table says 0.14 kg."},"tube_axis_below_top":{"label":"Tube axis below the stock's top edge","kind":"length","measurements":[{"id":"mouth","value":0.66,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/mft-battlelink-minimalist-stock f15b8c0be94f (Wing Tactical: the scorched dark earth stock straight from the front, into the tube's opening, 1280 x 1280)","scaleRef":"the mouth's own height, top edge to the neck's foot, 427 px (rows 120 to 547) = mouth_height 1.630 in from the maker's side view: 262 px/in; checked by what has to fit: the tube and its rail need 1.448 in of the 385 px between the bore's top and the channel's floor (at most 265.9 px/in), and the bore's round top is a 153 px arc (0.584 in at 262: the tube's 0.574 and a hundredth)","method":"the axis is row 293 ± 3: no higher than the bore's top (row 140) plus the tube's radius, no lower than the channel's floor (row 525) less the rail's foot (0.874 in below the axis); the housing's top is row 120 ± 4 (its edge is rounded: a band of rows 122 to 135); ± adds the scale's 2%","via":"harvest"}}],"note":"No photo shows the stock on a tube square from the side. Wing Tactical's straight view into the mouth shows the keyed bore: a round top and the indexing rail's channel under it, and a mil-spec tube with its rail (1.448 in from the tube's top to the rail's foot: std.receiver_extension) has to stand between the bore's top and the channel's floor, which are 385 px apart: 1.469 in at the mouth's scale, so the axis is fixed within 0.02 in. It lies level with the housing's widest line (the ridge along its side, 0.660 in below the top in the maker's side view)."},"rear_width":{"label":"Width of the housing's fuller rear part (the cheek part, behind the step in its side), where it begins","kind":"length","measurements":[{"id":"mouth","value":1.69,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/mft-battlelink-minimalist-stock f15b8c0be94f (Wing Tactical: the scorched dark earth stock straight from the front, into the tube's opening, 1280 x 1280)","scaleRef":"the mouth's own height (262 px/in at the mouth) and the lens 11.0 ± 0.6 in from it","method":"the silhouette's two sides over rows 385 to 425, columns 480 and 809: 329 px, at 3.8 in behind the mouth (where the step in the housing's side is at those heights in the side view): 11 / 14.8 of the mouth's scale; ± is the lens's distance (1.67 to 1.72) and the scale's 2%","via":"harvest"}}],"note":"What shows of it beside the mouth's lower slopes in the view into the mouth: a straight side each way, 329 px apart, from the rows where the mouth stops hiding it down to the ledge. Read through where the lens stood: 11.0 ± 0.6 in from the mouth (the stock's toe, 5.6 in behind the mouth, at row 1135; the lock pin's cross pin, 2.3 in behind, at row 525; the hole in the top, 2.1 to 2.5 in behind, lit at row 195: one lens, its axis meeting the mouth's plane at about row 472, puts all three there). The published width (1.752) is 0.06 more: this part further back, or this reading."},"rear_wall_top_below_top":{"label":"Where the rear part's side stands upright from: below the stock's top","kind":"length","measurements":[{"id":"mouth","value":0.89,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/mft-battlelink-minimalist-stock f15b8c0be94f (Wing Tactical: the scorched dark earth stock straight from the front, into the tube's opening, 1280 x 1280)","scaleRef":"the mouth's own height (262 px/in at the mouth) and the lens 11.0 ± 0.6 in from it, its axis at row 472","method":"row 385, the first at which the silhouette is wider than the mouth's own lower slope, carried to 3.8 in behind the mouth: row 472 + (385 - 472) x 14.8 / 11 = row 355 at the mouth's scale, 235 px below the top (row 120)","via":"harvest"}}],"note":"The highest the rear part's upright side shows beside the mouth (above it the mouth hides it). Between the ridge's height and here the rear part's side is drawn leaning out from the ridge's width to its own: the side view shows no line there."},"mouth_height":{"label":"Height of the housing's front face: its top to the foot of the neck under the tube","kind":"length","measurements":[{"id":"side","value":1.63,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/mft-battlelink-minimalist-stock 125d06ff6f12 (Mission First Tactical: BMSMIL_black_01, straight right side on white, 1567 x 1200)","scaleRef":"the stock's own length and height, 1546 px for 7.084 in and 1122 px for 5.22 in: 218.2 and 214.9 px/in, mean 216.6","method":"the front face from the top edge (row 47) to its lower corner (row 400): 353 px; ± is the two scales' spread and a pixel or two for the rounded corners","via":"harvest"}}],"note":"What the straight view into the mouth is scaled by: the one length of the mouth's plane that the calibrated side view shows."},"body_width":{"label":"Width of the housing at its mouth: across the ridge along each side","kind":"length","measurements":[{"id":"mouth","value":1.61,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/mft-battlelink-minimalist-stock f15b8c0be94f (Wing Tactical: the scorched dark earth stock straight from the front, into the tube's opening, 1280 x 1280)","scaleRef":"the mouth's own height, 427 px = mouth_height 1.630 in (262 px/in), checked by the tube and its rail, which have to stand in it (at most 265.9 px/in) and by the rail's channel (125 px, at least 0.49 in: at most 255 ± 8 px/in)","method":"the silhouette's widest rows (285 to 290): columns 427 to 850, 422 px; one plane, square to the lens; ± is the scale's 2.3% and two pixels","via":"harvest"}}],"note":"The housing's section is an arch over a ridge each side at the tube's height, leaning in below it to the neck round the indexing rail's channel. 0.14 in less than the published width, which is therefore not the mouth's."},"neck_width":{"label":"Width of the neck under the housing, round the indexing rail's channel","kind":"length","measurements":[{"id":"mouth","value":0.67,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/mft-battlelink-minimalist-stock f15b8c0be94f (Wing Tactical: the scorched dark earth stock straight from the front, into the tube's opening, 1280 x 1280)","scaleRef":"the mouth's own height, 427 px = mouth_height 1.630 in (262 px/in)","method":"the neck's two outer walls at the mouth, columns 550 and 725 over rows 472 to 540: 175 px","via":"harvest"}}]},"rail_channel_width":{"label":"Width of the channel under the bore, for the receiver extension's indexing rail","kind":"length","measurements":[{"id":"mouth","value":0.477,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/mft-battlelink-minimalist-stock f15b8c0be94f (Wing Tactical: the scorched dark earth stock straight from the front, into the tube's opening, 1280 x 1280)","scaleRef":"the mouth's own height, 427 px = mouth_height 1.630 in (262 px/in)","method":"the dark opening's two walls below the bore, columns 576 and 701 over rows 454 to 514 (luminance under 70): 125 px; ± is two pixels a side and the scale","via":"harvest"}}],"note":"Reads a hair under the rail it takes (std.receiver_extension.rail_width, .485 to .495): the mouth's rim is rounded and in its own shadow. Within its ±; the model cuts the channel at the rail's own width."},"rail_channel_floor_below_axis":{"label":"Floor of the indexing rail's channel, below the tube axis","kind":"length","measurements":[{"id":"mouth","value":0.885,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/mft-battlelink-minimalist-stock f15b8c0be94f (Wing Tactical: the scorched dark earth stock straight from the front, into the tube's opening, 1280 x 1280)","scaleRef":"the mouth's own height, 427 px = mouth_height 1.630 in (262 px/in)","method":"the opening's lowest row (525) below the axis (row 293 ± 3, tube_axis_below_top)","via":"harvest"}}],"note":"The mil-spec tube's rail reaches 0.874 in below its axis (std.receiver_extension.rail_bottom_below_axis): a hundredth to spare."},"block_width":{"label":"Width of the block under the neck's front: the QD socket's boss and the foot ahead of it","kind":"length","measurements":[{"id":"mouth","value":0.63,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/mft-battlelink-minimalist-stock f15b8c0be94f (Wing Tactical: the scorched dark earth stock straight from the front, into the tube's opening, 1280 x 1280)","scaleRef":"the mouth's own height (262 px/in at the mouth), and where the lens stood: about 11 in from the mouth (the stock's toe, 5.6 in behind the mouth, and the lock pin's cross pin, 2.3 in behind it, both land where a lens 11 ± 1.5 in away has them, its axis meeting the mouth's plane at row 481)","method":"the block's two sides under the neck, columns 570 and 720 over rows 560 to 690: 150 px, at 1.0 in behind the mouth (11/12 of the mouth's scale); ± is the lens's distance and three pixels","via":"harvest"}},{"id":"below","value":0.64,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/mft-battlelink-minimalist-stock 4063fa31cf9a (Mission First Tactical: BMSMIL_black_07, the right side from below, 1567 x 1200)","scaleRef":"the stock's own length in that view, 1465 px for the side outline's 7.138 in: 205 px/in (a view from below keeps lengths along the stock)","method":"the boss's two sides, columns 1130 and 1262","via":"harvest"}}],"adopt":{"from":"mouth","reason":"The view square across the block; the oblique agrees within 0.01 in."},"note":"Two views: the block's front face in the straight view into the mouth, an inch behind the mouth's plane; and the boss from below the right side, where its two sides read 132 px at that picture's 205 px/in (0.64 in). The straight side view has the boss 126 px along the stock (0.58 in): its edges there are shading, not silhouette. The bar behind the boss is narrower in both views from below, by an amount not read."},"frame_width":{"label":"Width of the frame behind the lever: the strut's front edge","kind":"length","measurements":[{"id":"mouth","value":0.47,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/mft-battlelink-minimalist-stock f15b8c0be94f (Wing Tactical: the scorched dark earth stock straight from the front, into the tube's opening, 1280 x 1280)","scaleRef":"the mouth's own height (262 px/in at the mouth) and the lens about 11 ± 1.5 in from it","method":"the strut's two edges seen under the block, columns 608 and 690 over rows 720 to 1100: 82 px, at 5.7 in behind the mouth (11/16.7 of the mouth's scale); ± is mostly the lens's distance","via":"harvest"}}],"note":"The strut down to the toe is a web between a rear plate as wide as the butt pad it carries and a front flange of this width; the web between them, with its slots, is thinner by a depth no view gives."},"web_thickness":{"label":"Thickness of the frame's web inside its flanges, at the slot behind the lever","kind":"length","measurements":[{"id":"oblique","value":0.25,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/mft-battlelink-minimalist-stock d267a6516961 (Mission First Tactical: BMSMIL_black_02, from the front left, 1567 x 1200)","scaleRef":"the stock's own height in that view, 1105 px for the side outline's 5.18 in: 213 px/in; the view's turn from square, 28 degrees, from the stock's length as it shows (1505 px for 7.138 in along it and the mouth's 1.61 in across)","method":"the slot's rear end wall, seen through the slot beside the white ground, is 25 px across on a 5x crop (columns 1200 to 1225): the web's thickness times the sine of the turn; ± is the turn's (3 degrees) and three pixels","via":"harvest"}}],"note":"The frame is a web between flanges: its panels are recessed each side by half of what this is less than frame_width. Read once, at one slot, in an oblique; the strut's panels and the cells under the housing's rear part are drawn recessed by the same depth, which no view gives."},"pad_width_low":{"label":"Width of the butt pad 3.0 in below the stock's top","kind":"length","measurements":[{"id":"mouth","value":1.42,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/mft-battlelink-minimalist-stock f15b8c0be94f (Wing Tactical: the scorched dark earth stock straight from the front, into the tube's opening, 1280 x 1280)","scaleRef":"the mouth's own height (262 px/in at the mouth) and the lens about 11 ± 1.5 in from it","method":"the pad's two sides behind the strut over rows 700 to 800 (which are 3.0 in below the top at the pad's distance): 235 px, at 6.7 in behind the mouth (11/17.7 of the mouth's scale); ± is mostly the lens's distance","via":"harvest"}}]},"pad_width_toe":{"label":"Width of the butt pad at its toe","kind":"length","measurements":[{"id":"mouth","value":1.2,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/mft-battlelink-minimalist-stock f15b8c0be94f (Wing Tactical: the scorched dark earth stock straight from the front, into the tube's opening, 1280 x 1280)","scaleRef":"the mouth's own height (262 px/in at the mouth) and the lens about 11 ± 1.5 in from it","method":"the pad's two sides at rows 1080 to 1110: 198 px, at 6.7 in behind the mouth","via":"harvest"}}]},"pad_width_low_below_top":{"label":"Where the butt pad's lower width was read: below the stock's top","kind":"length","measurements":[{"id":"mouth","value":3,"unit":"in","pm":0.3,"source":{"type":"photo","photo":"references/mft-battlelink-minimalist-stock f15b8c0be94f (Wing Tactical: the scorched dark earth stock straight from the front, into the tube's opening, 1280 x 1280)","scaleRef":"the mouth's own height (262 px/in at the mouth) and the lens about 11 ± 1.5 in from it, its axis meeting the mouth's plane at row 481","method":"rows 700 to 800, at 6.7 in behind the mouth: 481 + (750 - 481) x 17.7 / 11 = row 914 at the mouth's scale, 794 px below the top (row 120)","via":"harvest"}}],"note":"The rows the pad shows at behind the strut in the view into the mouth, carried back to the pad's own distance. The pad is drawn tapering from the published width at the ridge's height to pad_width_low here and to pad_width_toe at its foot."},"top_hole_diameter":{"label":"Hole in the housing's top, over the lock pin: its length along the stock","kind":"length","measurements":[{"id":"photo","value":0.39,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/mft-battlelink-minimalist-stock 125d06ff6f12 (Mission First Tactical: BMSMIL_black_01, straight right side on white, 1567 x 1200)","scaleRef":"the stock's own length and height: 218.2 and 214.9 px/in, mean 216.6","method":"the dip in the top edge, columns 1010 to 1095 on a 2x crop: 85 px, its middle at column 1052 (the lock pin's is 1053)","via":"harvest"}}],"note":"A dip in the top edge of each side view over the lock pin, and a lit crescent on the bore's roof in the view into the mouth; a buyer on Primary Arms' page writes of the 'removal of pin from the hole at the top'. Drawn round, which no view shows."},"lock_pin_ahead_of_butt":{"label":"Lock pin ahead of the butt's rearmost point","kind":"length","measurements":[{"id":"photo","value":4.83,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/mft-battlelink-minimalist-stock 125d06ff6f12 (Mission First Tactical: BMSMIL_black_01, straight right side on white, 1567 x 1200)","scaleRef":"the stock's own length and height, 1546 px for 7.084 in and 1122 px for 5.22 in: 218.2 and 214.9 px/in, mean 216.6","method":"the cross pin's end is a bright round at column 1053 (rows 379 to 403), the spring's window under it columns 1040 to 1068: 1046 px ahead of the pad's rearmost point (column 7) and 499 px (2.30 in) behind the front; ± is the two scales' spread (4.79 to 4.87) and a pixel or two","via":"harvest"}}],"note":"The steel pin the lever draws down out of the receiver extension's holes. It stands upright in the neck's floor: its cross pin's rounded end shows under the lever's front in each side view, over the coil spring in its window; its top shows in the channel in the view into the mouth, and its foot from below. A notch in the housing's top edge stands over it (columns 1010 to 1095). Where it stands says which hole the stock is on."},"cross_pin_length":{"label":"Lock pin's cross pin, end to end (what the lever bears on each side)","kind":"length","measurements":[{"id":"mouth","value":1.08,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/mft-battlelink-minimalist-stock f15b8c0be94f (Wing Tactical: the scorched dark earth stock straight from the front, into the tube's opening, 1280 x 1280)","scaleRef":"the mouth's own height (262 px/in at the mouth) and the lens about 11 ± 1.5 in from it","method":"the dark pin's two ends beside the neck's foot, columns 520 and 755 at row 525: 235 px, at 2.3 in behind the mouth (11/13.3 of the mouth's scale)","via":"harvest"}}],"note":"The lever is a fork: a plate each side of the neck on one pivot pin, their front ends over this pin's two ends, joined by the paddle under the frame. The fork is drawn as wide as this pin is long."},"cross_pin_diameter":{"label":"Lock pin's cross pin, diameter","kind":"length","measurements":[{"id":"photo","value":0.11,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/mft-battlelink-minimalist-stock 125d06ff6f12 (Mission First Tactical: BMSMIL_black_01, straight right side on white, 1567 x 1200)","scaleRef":"the stock's own length and height: 218.2 and 214.9 px/in, mean 216.6","method":"its bright rounded end on a 3x crop: 24 px across","via":"harvest"}}]},"pivot_pin_diameter":{"label":"Lever's pivot, diameter","kind":"length","measurements":[{"id":"photo","value":0.148,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/mft-battlelink-minimalist-stock 125d06ff6f12 (Mission First Tactical: BMSMIL_black_01, straight right side on white, 1567 x 1200)","scaleRef":"the stock's own length and height: 218.2 and 214.9 px/in, mean 216.6","method":"the round in the lever's plate, centre (877, 384), on a 3x crop: 32 px across","via":"harvest"}}],"note":"A round in the lever's plate each side: black on the black stock and the earth colour on the earth one (the maker's pictures of each), so a boss of the body or a pin of its polymer, not steel."},"lock_pin_diameter":{"label":"Lock pin, diameter","kind":"length","measurements":[{"id":"below","value":0.234,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/mft-battlelink-minimalist-stock 4063fa31cf9a (Mission First Tactical: BMSMIL_black_07, the right side from below, 1567 x 1200)","scaleRef":"the stock's own length in that view, 1465 px for the side outline's 7.138 in: 205 px/in","method":"the pin's round foot in the bar's underside, 48 px along the stock (a 4x crop)","via":"harvest"}},{"id":"mouth","value":0.254,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/mft-battlelink-minimalist-stock f15b8c0be94f (Wing Tactical: the scorched dark earth stock straight from the front, into the tube's opening, 1280 x 1280)","scaleRef":"the mouth's own height (262 px/in at the mouth) and the lens about 11 ± 1.5 in from it","method":"the dark pin standing in the channel, columns 610 to 665: 55 px, at 2.3 in behind the mouth","via":"harvest"}}],"adopt":{"from":"below","reason":"The foot's own rim, sharp against the bar; the view into the mouth agrees within its ±."},"note":"Its foot, flush in the underside of the bar under the neck, and its top in the channel."},"spring_wire_diameter":{"label":"Lock pin's spring, wire diameter","kind":"length","measurements":[{"id":"photo","value":0.035,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/mft-battlelink-minimalist-stock 125d06ff6f12 (Mission First Tactical: BMSMIL_black_01, straight right side on white, 1567 x 1200)","scaleRef":"the stock's own length and height: 218.2 and 214.9 px/in, mean 216.6","method":"a lit turn of the wire in the window on a 3x crop: 7 to 8 px","via":"harvest"}}],"note":"Three turns show in its window: three lit strands 26 px apart in the maker's earth-colour three-quarter picture (45347093555f, about 240 px/in: a turn every 0.11 in), where the black side view's dark runs, 13 px apart, count the far side of each turn too."},"qd_bore_diameter":{"label":"QD socket: the diameter of its mouth","kind":"length","measurements":[{"id":"below","value":0.365,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/mft-battlelink-minimalist-stock 4063fa31cf9a (Mission First Tactical: BMSMIL_black_07, the right side from below, 1567 x 1200)","scaleRef":"the stock's own length in that view, 1465 px for the side outline's 7.138 in: 205 px/in (a view from below keeps lengths along the stock)","method":"the dark mouth's extent along the stock, columns 1175 to 1250 on a 4x crop: 75 px (its height in the picture, 55 px, is foreshortened)","via":"harvest"}}],"note":"The socket stands upright in the block under the neck, on the stock's centre, its mouth in the underside (the maker: 'Quick Detach Sling mounting point is positioned for optimum usage including ambidextrous shooters'; Redcon1's table: 'Sling Mount Type QD Swivel Socket'). A dark, glossy cup shows in it: steel, by its shine, on the black stock and the earth one alike."},"qd_rim_diameter":{"label":"QD socket: the outer diameter of the steel cup's rim in the underside","kind":"length","measurements":[{"id":"below","value":0.424,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/mft-battlelink-minimalist-stock 4063fa31cf9a (Mission First Tactical: BMSMIL_black_07, the right side from below, 1567 x 1200)","scaleRef":"the stock's own length in that view: 205 px/in","method":"the bright ring round the dark mouth, columns 1168 to 1255: 87 px","via":"harvest"}}]},"butt_behind_pin_pos1":{"label":"Butt behind the takedown pin at position 1 (collapsed), on a carbine receiver extension","kind":"length","measurements":[{"id":"holes","value":9.009,"unit":"in","pm":0.08,"source":{"type":"derived","expr":"{bcm-receiver-extension.tube_front_behind_pin} + {bcm-receiver-extension.tube_length} - {bcm-receiver-extension.position_hole_rear_from_rear} - 5 * {bcm-receiver-extension.position_step} + {.lock_pin_ahead_of_butt}","via":"harvest"},"note":"The lock pin in the tube's front hole. ± for the hole's place (0.03), the tube's seat (0.02) and the pin's place in the stock (0.04), and for the tube's length, which is a generic figure."},{"id":"wing-installed","value":9.08,"unit":"in","pm":0.12,"source":{"type":"photo","photo":"references/mft-battlelink-minimalist-stock 3cc9b4ed6bff (Wing Tactical: the black stock on a rifle, close, from the right, behind and a little below; the tube's thread, the castle nut, the end plate and the takedown pin's head in frame, 1280 x 1280)","scaleRef":"the stock's own lock pin to its front along its lower edge: 296 px for 2.30 in in the maker's side view (128.6 px/in on its near side; the tube ahead of it is further from that lens, down to about 122)","method":"along the tube's top edge the stock's front corner (888, 348) is 108 px behind the castle nut's rear face (992, 318): 0.84 to 0.89 in, taken as 0.86; added to the nut's place (bcm-castle-nut.rear_face_behind_pin, 1.74) and the side outline's length (7.138), less one step of the tube's holes (0.66), the stock being read as one hole out; ± is the oblique's scale along the tube and where the nut's face is taken","via":"harvest"},"note":"An oblique from close by, read within what it allows: the one length along the tube, scaled by a length of the stock beside it. Which hole it shows is told by the other seat, not said by the shop."}],"adopt":{"from":"holes","reason":"The stock's own half of the seat (its lock pin) on the tube's own (its front hole), each from a square view. Wing Tactical's oblique of it on a rifle agrees within 0.07 in once read as one hole out, and is kept as the check it is."},"note":"No page gives a length of pull and no photo shows the stock on a rifle square from the side. It is seated by its own lock pin in the tube's front hole (where the Army's drawings seat the tube and BCM's photo places its holes: bcm-receiver-extension), which leaves its front 0.13 in behind the castle nut (bcm-castle-nut.rear_face_behind_pin, with the side outline's 7.138 in length). The check is Wing Tactical's close photo of it on a rifle, from the right, behind and below: there its front stands 0.86 in behind the nut, which is this seat one hole out (0.13 + 0.66 = 0.79) and no other hole (the next are 0.66 either way)."},"lop_collapsed":{"label":"Length of pull, collapsed (the maker's reference rifle)","kind":"length","measurements":[],"note":"Mission First Tactical publishes none (its page, its 2013 release and eight sellers' pages read 2026-10-13)."},"lop_extended":{"label":"Length of pull, extended (the maker's reference rifle)","kind":"length","measurements":[],"note":"Mission First Tactical publishes none."}}},{"subject":"midwest-combat-rail-15-handguard","title":"Midwest Industries Combat Rail One Piece Free Float Handguard, M-LOK, 15 in (MI-CRM15)","dimensions":{"weight":{"label":"Weight on the rifle (the handguard with its barrel nut, torque plate and two clamp screws)","kind":"mass","measurements":[{"id":"maker","value":11.4,"unit":"oz","pm":0.05,"stated":"Installed Weights [...] 15.0\" - 11.4oz","source":{"type":"spec","publisher":"manufacturer","name":"Midwest Industries, Combat Rail One Piece Free Float Handguard, M-LOK™ (15 in: MI-CRM15), Product Details","url":"https://midwestindustriesinc.com/mi-combat-rail-one-piece-free-float-handguard-m-lok-tm/","retrieved":"2026-10-12","via":"harvest"}},{"id":"wing","value":11.36,"unit":"oz","pm":0.005,"stated":"Weight (with Barrel Nut): [...] 15-inch: 11.36 oz.","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Midwest Industries M-LOK Combat Rail (MPN: MI-CRM10.5 / MI-CRM12.625 / MI-CRM14 / MI-CRM15), Specifications","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/handguards-rails/rail-systems/midwest-industries-m-lok-combat-rail/","retrieved":"2026-10-12","via":"harvest"}},{"id":"primary-arms","value":11.4,"unit":"oz","pm":0.05,"stated":"15\" overall length, 11.4 oz installed weight","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Midwest Industries Combat Rail Free Float AR-15 Handguard - M-LOK - 15\" (SKU and MPN MI-CRM-15.0)","url":"https://www.primaryarms.com/midwest-industries-15in-combat-rail-m-lok-ar-15-handguard-black","retrieved":"2026-10-12","via":"harvest"}}],"adopt":{"from":"maker","reason":"The maker's figure; a seller's own weighing with the barrel nut reads 0.04 oz less, inside its one decimal."},"note":"The maker's table is headed \"Installed Weights\": what goes on the rifle. Wing Tactical's own figure for this length says what is in it: \"Weight (with Barrel Nut)\". No page gives the handguard's aluminium alone (weight_handguard is worked out)."},"weight_nut":{"label":"Weight, its barrel nut (worked out from its steel)","kind":"mass","measurements":[{"id":"metal","value":1.05,"unit":"oz","pm":0.4,"source":{"type":"derived","expr":"0.785398163 * ({.nut_od} * {.nut_od} - {.nut_bore} * {.nut_bore}) * {.nut_length} * {std.density.steel}","via":"harvest"}}],"note":"WORKED OUT, not published: no page weighs the nut. A plain ring of its outside diameter, its threaded bore and its length, each read off a photo, times std.density.steel (the maker: \"4140 Heat Treated Barrel Nut\"). Its inner lip at the muzzle end adds a little and its groove, its notches and its knurl take a little off: neither is counted. The ± is what the three readings leave."},"weight_screws":{"label":"Weight, its two clamp screws (worked out from their steel)","kind":"mass","measurements":[{"id":"metal","value":0.247,"unit":"oz","pm":0.07,"source":{"type":"derived","expr":"2 * 0.785398163 * ({.screw_d} * {.screw_d} * {.screw_length} + {.screw_head_d} * {.screw_head_d} * {.screw_head_height}) * {std.density.steel}","via":"harvest"}}],"note":"WORKED OUT, not published. Two socket head cap screws, each a shank of the stated length and a head, as plain rounds (the sockets aren't taken off), times std.density.steel."},"weight_plate":{"label":"Weight, its torque plate (worked out from its steel)","kind":"mass","measurements":[{"id":"metal","value":0.099,"unit":"oz","pm":0.04,"source":{"type":"derived","expr":"{.plate_length} * {.plate_height} * {.plate_thickness} * {std.density.steel}","via":"harvest"}}],"note":"WORKED OUT, not published. A flat plate of its length, height and thickness as read, times std.density.steel (the maker: \"Patented 4140 Heat Treated Torque Plate\"); its two holes and its post aren't counted, which about cancel."},"weight_handguard":{"label":"Weight, the handguard's aluminium alone (worked out)","kind":"mass","measurements":[{"id":"rest","value":10.005,"unit":"oz","pm":0.45,"source":{"type":"derived","expr":"{.weight} - {.weight_nut} - {.weight_screws} - {.weight_plate}","via":"harvest"}}],"note":"WORKED OUT, not published: the installed weight less the steel that is weighed with it (the nut, the two screws, the plate), each of which is itself worked out from sizes read off photos. What the model's aluminium is held to."},"length":{"label":"Length, end to end (its rear face to the tips of its muzzle end, the tabs behind the rear face left out)","kind":"length","measurements":[{"id":"maker","value":15,"unit":"in","pm":0.05,"stated":"15.0\" - 11.4oz","source":{"type":"spec","publisher":"manufacturer","name":"Midwest Industries, Combat Rail One Piece Free Float Handguard, M-LOK™ (15 in: MI-CRM15), Product Details","url":"https://midwestindustriesinc.com/mi-combat-rail-one-piece-free-float-handguard-m-lok-tm/","retrieved":"2026-10-12","via":"harvest"}},{"id":"midwest-gun-works","value":15,"unit":"in","pm":0.05,"stated":"15.0\" overall length","source":{"type":"spec","publisher":"retailer","name":"Midwest Gun Works, Midwest Industries AR-15 Combat Rail M-Lok Handguard, 15\" Black (Code: MI-CRM15)","url":"https://www.midwestgunworks.com/page/mgwi/prod/mi-crm15","retrieved":"2026-10-12","via":"harvest"}},{"id":"right-to-bear","value":15,"unit":"in","pm":0.5,"stated":"15\" overall length","source":{"type":"spec","publisher":"retailer","name":"Right to Bear, Midwest Industries Combat Rail One Piece Free Float Handguard 15\" - M-LOK (SKU: MI-CRM15)","url":"https://www.righttobear.com/midwest-combat-rail-free-float-handguard-15-inch-mi-crm15/","retrieved":"2026-10-12","via":"harvest"}},{"id":"photo","value":14.95,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own top rail's 36 slots at the Picatinny pitch (std.picatinny.slot_pitch), each column read as a rail coordinate","method":"the rail's rear end (its near corner at px 142, 13 px nearer the lens's column in the mid-plane: half what the notches have narrowed by there) 1.575 pitches behind the rearmost slot's centre (px 232.5), its front end (px 2066, 10 px likewise) 1.243 ahead of the foremost (px 1993.5): 37.82 pitches, 14.89 in; the side face's tip (px 2080, at k 1.021) 0.143 pitch further: 14.945. The left photo e1fb6c9b2da4 reads the rail 14.91 and the tips 0.045 further (m2.py, m4.py)","via":"harvest"}}],"adopt":{"from":"maker","reason":"The maker's figure to its one decimal; two photos read 14.95, inside both ±."},"note":"The maker names the size 15.0\" in its table of weights and 15\" in its list of lengths; sellers write it as the overall length. By its own rail it reads 14.95: the rail 14.90 from end to end (36 slots and two lands) and the side faces' tips 0.05 further."},"width":{"label":"Width across the side faces (3 to 9 o'clock)","kind":"length","measurements":[{"id":"maker","value":1.5,"unit":"in","pm":0.05,"stated":"Super Slim 1.5” Outside and 1.3” Inside Diameter","source":{"type":"spec","publisher":"manufacturer","name":"Midwest Industries, Combat Rail One Piece Free Float Handguard, M-LOK™ (15 in: MI-CRM15), Product Details","url":"https://midwestindustriesinc.com/mi-combat-rail-one-piece-free-float-handguard-m-lok-tm/","retrieved":"2026-10-12","via":"harvest"}},{"id":"wing","value":1.5,"unit":"in","pm":0.05,"stated":"Width: 1.5\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Midwest Industries M-LOK Combat Rail (MPN: MI-CRM10.5 / MI-CRM12.625 / MI-CRM14 / MI-CRM15), Specifications","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/handguards-rails/rail-systems/midwest-industries-m-lok-combat-rail/","retrieved":"2026-10-12","via":"harvest"}}],"adopt":{"from":"maker","reason":"The maker's; a seller states the same figure as a width."},"note":"The maker's \"1.5” Outside ... Diameter\" is a size, not a shape: the section has flat faces. Wing Tactical gives it as a width beside a height. The bottom flat stands the same 0.75 in from the bore (body_bottom_below_bore), and the faces between are taken to (diag_face_distance)."},"height":{"label":"Height (the rail's top to the bottom flat; the clamp lug under the rear end left out)","kind":"length","measurements":[{"id":"wing","value":1.97,"unit":"in","pm":0.005,"stated":"Height: 1.97\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Midwest Industries M-LOK Combat Rail (MPN: MI-CRM10.5 / MI-CRM12.625 / MI-CRM14 / MI-CRM15), Specifications","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/handguards-rails/rail-systems/midwest-industries-m-lok-combat-rail/","retrieved":"2026-10-12","via":"harvest"}},{"id":"photo","value":1.95,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own rail's slots beside the lens's column: 50.8 px a pitch, 129.0 px/in in the mid-plane, each edge at its own depth from a lens 35 in away","method":"at the lens's column: the rail's top (row 607, its near edge 0.37 in nearer the lens) to the bottom flat's near edge (row 861, 0.25 nearer), about a principal row taken at the image's middle (733): 0.9665 above it and 0.985 below (m2.py)","via":"harvest"}}],"adopt":{"from":"wing","reason":"The one published figure, from a seller's own table; the level photo reads 0.02 less, inside its ±."},"note":"What Wing Tactical's 1.97 in spans is read on the level photo: the rail's top to the bottom flat is 1.95 there; to the bottom of the clamp lug under the rear end it would be 2.34. Half the width below the bore and a mil-spec receiver's rail above it (1.2125, bcm-m4-upper) come to 1.9625."},"inside_diameter":{"label":"Inside diameter (across the inner flats)","kind":"length","measurements":[{"id":"maker","value":1.3,"unit":"in","pm":0.05,"stated":"Super Slim 1.5” Outside and 1.3” Inside Diameter","source":{"type":"spec","publisher":"manufacturer","name":"Midwest Industries, Combat Rail One Piece Free Float Handguard, M-LOK™ (15 in: MI-CRM15), Product Details","url":"https://midwestindustriesinc.com/mi-combat-rail-one-piece-free-float-handguard-m-lok-tm/","retrieved":"2026-10-12","via":"harvest"}},{"id":"wing","value":1.3,"unit":"in","pm":0.05,"stated":"Inner Diameter: 1.3\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Midwest Industries M-LOK Combat Rail (MPN: MI-CRM10.5 / MI-CRM12.625 / MI-CRM14 / MI-CRM15), Specifications","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/handguards-rails/rail-systems/midwest-industries-m-lok-combat-rail/","retrieved":"2026-10-12","via":"harvest"}},{"id":"primary-arms","value":1.3,"unit":"in","pm":0.05,"stated":"Inner Diameter 1.3","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Midwest Industries Combat Rail Free Float AR-15 Handguard - M-LOK - 15\" (SKU and MPN MI-CRM-15.0)","url":"https://www.primaryarms.com/midwest-industries-15in-combat-rail-m-lok-ar-15-handguard-black","retrieved":"2026-10-12","via":"harvest"}}],"adopt":{"from":"maker","reason":"The maker's; two sellers repeat it."},"note":"The maker's \"1.3” Inside Diameter\": ahead of the barrel nut the inside has flat walls that follow the outside (Primary Arms' view of the muzzle end, fac9b67f0d22), and the model takes this figure across the inner side flats, which leaves a wall of 0.1 in. The light through the slots of the faces at 45 degrees is 17 px tall on the level photo where a wall of no thickness would show 25: a wall of 0.09 in. Over the barrel nut the bore is round and larger (nut_od)."},"rear_face_x":{"label":"Its rear face against the receiver's front face (negative: behind it)","kind":"length","measurements":[{"id":"derived","value":-0.445,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"0in - {std.ar15.upper_barrel_thread_length}","via":"harvest"}}],"note":"No page says where it stops and no photo of this handguard mounted is on file (Wing Tactical's pictures of a complete upper are of the Lightweight Combat Rail, another product). It slides back over its barrel nut until its two tabs lie along the receiver's sides (Primary Arms: \"Indexing tabs key the handguard against the receiver to keep it from rotating under recoil\"): its rear face is taken to meet the receiver's front shoulder, where the barrel-nut thread begins (std.ar15.upper_barrel_thread_length behind the front face), with no gap. A check that isn't a photo: its rail's first slot then stands 0.01 in from where the receiver's own row of slots would continue at the standard's pitch (bcm-m4-upper), and the maker calls the rail \"Continuous MIL-STD 1913 Picatinny Top rail\"."},"tab_length":{"label":"Its two tabs' reach behind its rear face","kind":"length","measurements":[{"id":"photo","value":0.165,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own top rail's 36 slots at the Picatinny pitch (std.picatinny.slot_pitch), each column read as a rail coordinate","method":"the tab's rear end (px 118, rows 690 to 703) behind the side face's rear edge (px 138): 20 px at 126.8 px/in (49.1 px a pitch at the rear end, 1.7% more at the tab's depth): 0.158; the left photo reads 22 px, 0.173 (m4.py)","via":"harvest"}}],"note":"Wing Tactical: \"Two integral anti-rotation tabs\". Each is the wall of an upper face (between a side face and the neck under the rail) carried on behind the rear face, its end cut to a blunt point: one each side, seen on both level photos and, from behind, on Wing Tactical's and the maker's pictures of the rear end."},"tab_gap":{"label":"The opening between its two tabs' inner faces","kind":"length","measurements":[{"id":"derived","value":0.638,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"2 * {bcm-m4-upper.side_half_width}","via":"harvest"}}],"note":"Not measured: no view shows it square on. The tabs stand beside a mil-spec receiver's flat sides under its rail (0.56 to 0.82 in above the bore on the catalog's receivers), which is what keeps the handguard from turning, and their inner faces are drawn against those flats with no clearance."},"rear_x":{"label":"The outline's rear end (its tabs' ends) against the receiver's front face (negative: behind it)","kind":"length","measurements":[{"id":"derived","value":-0.61,"unit":"in","pm":0.045,"source":{"type":"derived","expr":"{.rear_face_x} - {.tab_length}","via":"harvest"}}]},"overall_length":{"label":"Length over all, its tabs' ends to its muzzle end","kind":"length","measurements":[{"id":"derived","value":15.165,"unit":"in","pm":0.055,"source":{"type":"derived","expr":"{.length} + {.tab_length}","via":"harvest"}}]},"body_bottom_below_bore":{"label":"The bottom flat below the bore axis","kind":"length","measurements":[{"id":"photo","value":0.75,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own rail's slots beside the lens's column: 129.0 px/in in the mid-plane, each edge at its own depth from a lens 35 in away","method":"the bottom flat's near edge (row 861) below the middle of the light through the side rows' slots (row 764, on the near face): 0.985 and 0.235 below the principal row: 0.750. The left photo: 97.5 px between the same two, the right one 97 (m2.py)","via":"harvest"}}],"note":"The bore's axis is taken on the side faces' rows of M-LOK slots (the light through them, both walls: rows 746 to 782 at the lens's column), which is where the sling sockets also stand. The bottom flat is then half the published width below it: the tube is as deep below the bore as it is wide either side."},"rail_top_above_bore":{"label":"Its rail's top above the bore axis","kind":"length","measurements":[{"id":"derived","value":1.22,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{.height} - {.body_bottom_below_bore}","via":"harvest"}},{"id":"photo","value":1.2,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own rail's slots beside the lens's column: 129.0 px/in in the mid-plane, each edge at its own depth from a lens 35 in away","method":"the rail's top (row 607) above the middle of the light through the side rows' slots (row 764): 0.9665 above the principal row and 0.235 below it (m2.py)","via":"harvest"}}],"adopt":{"from":"derived","reason":"The published height over the bottom's depth; the photo's own reading of the rail's top is 0.02 less, inside its ±, and a mil-spec receiver's rail is between the two."},"note":"Not published as such: the published height less the bottom flat's depth below the bore. The catalog's mil-spec receivers have their rail 1.2125 and 1.2145 in above the bore (bcm-m4-upper, expo-arms-stripped-upper), which this is within a hundredth of: the maker's \"Continuous\" rail."},"side_flat_height":{"label":"The side faces' flat height (between the two narrow faces that break its corners)","kind":"length","measurements":[{"id":"photo","value":0.478,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own rail's slots beside the lens's column, 2.1% more on the near side face: 131.8 px/in","method":"a column through the bar between two slots beside the lens's column (px 1192): the side face in shadow from row 732 to row 795, between two lighter bands: 63 px (m2.py; the left photo, px 1000: rows 708 to 770, 62 px)","via":"harvest"}}],"note":"Centred on the bore: the middle of the flat is the middle of the light through the side rows' slots within a pixel. A regular octagon 1.5 in across would have 0.621 here; the corners between each side face and the faces at 45 degrees are broken by a narrow face (corner_chamfer_height), which is where the small scallops are cut."},"corner_chamfer_height":{"label":"The narrow face between each side face and the face at 45 degrees beside it, its height as seen from the side","kind":"length","measurements":[{"id":"photo","value":0.106,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own rail's slots beside the lens's column, 2.1% more on the near side face: 131.8 px/in","method":"the same column: the lighter band above the side face, rows 718 to 731, and the one below it, rows 796 to 809: 14 px each (m2.py; the left photo: rows 694 to 706 and 770 to 784)","via":"harvest"}}],"note":"A corner broken evenly on a regular octagon 1.5 in across, from where the side face's flat ends (0.239 from the bore's height), would end 0.361 from it on the face at 45 degrees: the band reads to 0.345. The corners between the lower faces and the bottom flat show the same narrow face, 5 px tall at the foot of the level photo."},"diag_face_distance":{"label":"The faces at 45 degrees (between the sides and the rail, and between the sides and the bottom): their distance from the bore axis","kind":"length","measurements":[{"id":"derived","value":0.75,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{.width} / 2","via":"harvest"}}],"note":"Taken as the side faces' and the bottom's: a regular octagon about the bore, which is what the maker's one \"1.5” Outside ... Diameter\" for a section with flat faces says, with the faces at 45 degrees (Wing Tactical: \"allow user to mount accessories at 45-degree\"). Three checks on the level photo: the bottom flat reads 0.75 below the bore (body_bottom_below_bore); the narrow faces at the side faces' corners straddle where a regular octagon's corners are (0.311 from the bore's height: corner_chamfer_height); and the upper faces end 0.664 above the bore, 0.397 from the middle at this distance, just outside a neck of 0.345 (the narrow shelf the views from behind show under the neck)."},"neck_base_above_bore":{"label":"Where the upper faces end and the shelf under the neck begins, above the bore","kind":"length","measurements":[{"id":"photo","value":0.664,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own rail's slots beside the lens's column, 1.2% more at this edge's depth: 130.5 px/in","method":"the line under the row of round holes (row 677 on a 3x crop of the muzzle end), 0.429 above the principal row, the bore 0.235 below it (m2.py)","via":"harvest"}}]},"neck_width":{"label":"The neck's width under the rail (across its two walls)","kind":"length","measurements":[{"id":"photo","value":0.69,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"the rail's own notches on the same photo: they lose 0.0239 of their distance from the lens's column, for a rail 0.835 in wide","method":"the light through each round hole is 0.61 pitch long at the lens's column and 0.302 sixteen pitches from it: 0.0193 a pitch, 0.672 in across the neck; the left photo reads 0.0169 against its notches' 0.0199: 0.710 (m2.py)","via":"harvest"}}],"note":"Narrower than the rail's 0.835: the rail's lower faces come in to it. Read from how the light through the neck's round holes narrows away from the lens's column, against how the rail's notches do (the rail is 0.835 wide: std.picatinny.top_width)."},"neck_wall":{"label":"The neck's walls, their thickness","kind":"length","measurements":[{"id":"rear-view","value":0.06,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 373fa3ba37aa (Wing Tactical's gallery for the M-LOK Combat Rail, 58126: a Combat Rail seen from behind and its right, the rear end near, 1280 x 1280; which of its four lengths isn't stated)","scaleRef":"the neck's own width on its rear face (this ledger's neck_width over 575 px on an 8x crop)","method":"each wall of the opening under the rail, about 50 px of the 575 between the neck's outer faces (the opening itself 470)","via":"harvest"},"note":"The rear end is the same on every length of this handguard (the maker's pictures of thirteen)."}]},"channel_roof_below_top":{"label":"The channel under the rail (the gas tube's), its roof below the rail's top","kind":"length","measurements":[{"id":"rear-view","value":0.15,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 373fa3ba37aa (Wing Tactical's gallery for the M-LOK Combat Rail, 58126: a Combat Rail seen from behind and its right, the rear end near, 1280 x 1280; which of its four lengths isn't stated)","scaleRef":"the neck's own height on its rear face (the rail's top to the shelf, 0.556 in by this ledger, over 527 px on an 8x crop)","method":"the opening's top edge 126 to 150 px below the rear face's top edge beside it: 0.13 to 0.16","via":"harvest"}}],"note":"Weakly read: an oblique view, and the rear face's top edge is broken. Deeper than the rail's slots (std.picatinny.slot_depth), as it has to be."},"rail_slots":{"label":"Slots in its top rail","kind":"count","measurements":[{"id":"photo","value":36,"unit":"count","source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"none: a count","method":"the notches of the silhouette's top edge (luminance under 235): 36, centres from px 232.5 to px 1993.5, each 49 to 52 px from the next with none missing, a longer land at each end; 36 again on the left photo e1fb6c9b2da4 (px 206 to 1965.5) (m2.py)","via":"harvest"}}]},"rail_slot0_from_rear":{"label":"Its rail's rearmost slot (its centre) ahead of its rear face","kind":"length","measurements":[{"id":"photo","value":0.62,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own top rail's 36 slots at the Picatinny pitch (std.picatinny.slot_pitch), each column read as a rail coordinate","method":"the rail's rear end (its near corner at px 142, 13 px nearer the lens's column in the mid-plane) behind the rearmost slot's centre (px 232.5): 77.5 px at 49.2 px a pitch, 1.575 pitches; the left photo reads 1.584 (m2.py, m4.py)","via":"harvest"}}],"note":"The rail's rear end is the body's rear face (the views from behind show one plane; the level photos read the side faces' rear edge within 0.04 in of it either way)."},"rail_slot0_x":{"label":"Its rail's rearmost slot (its centre) ahead of the receiver's front face","kind":"length","measurements":[{"id":"derived","value":0.175,"unit":"in","pm":0.045,"source":{"type":"derived","expr":"{.rear_face_x} + {.rail_slot0_from_rear}","via":"harvest"}}]},"rail_front_from_last_slot":{"label":"Its rail's front end ahead of its last slot's centre","kind":"length","measurements":[{"id":"photo","value":0.5,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own top rail's 36 slots at the Picatinny pitch (std.picatinny.slot_pitch), each column read as a rail coordinate","method":"the rail's front end (its near corner at px 2066, 10 px nearer the lens's column in the mid-plane) ahead of the foremost slot's centre (px 1993.5): 62.5 px at 50.3 px a pitch, 1.243 pitches, 0.489 in; the left photo reads 1.282 pitches, 0.505 (m2.py, m4.py)","via":"harvest"}}]},"rail_length":{"label":"Its rail, end to end","kind":"length","measurements":[{"id":"derived","value":14.91,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.rail_slot0_from_rear} + ({.rail_slots} - 1) * {std.picatinny.slot_pitch} + {.rail_front_from_last_slot}","via":"harvest"}}]},"nose_bottom_run":{"label":"Its muzzle end: how far behind the side faces' tips the bottom flat ends","kind":"length","measurements":[{"id":"photo","value":0.48,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own top rail's 36 slots at the Picatinny pitch (std.picatinny.slot_pitch), each column read as a rail coordinate","method":"the bottom edge leaves its line at px 2014 and the side face's tip is at px 2080, each brought to the mid-plane about the lens's column at its own depth (k 1.0075 and 1.021): 55.4 px at 127.3 px/in, 0.435 in; the left photo, the same way, 0.525 (m4.py)","via":"harvest"}}],"note":"The muzzle end is cut to a blunt point: the side faces run furthest forward, the upper faces slope back to the neck's front under the rail's end, and the lower faces and the bottom slope back further. The two photos differ by 0.09 in here, more than anywhere else: the value is between them."},"mlok_side_slots":{"label":"M-LOK slots on each side face (3 and 9 o'clock)","kind":"count","measurements":[{"id":"photo","value":7,"unit":"count","source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"none: a count","method":"the light through the middle row (row 764): seven long runs 199 to 207 px apart and one short one behind them (px 507 to 554); the same seven and one on the left photo (row 738) (m2.py)","via":"harvest"}}],"note":"Seven full slots; behind the rearmost, where an eighth would be, a short cut 0.64 in long takes the front half of the place and a sling socket stands behind it (short_slot_length, socket_from_rear). The maker: \"Seven Sides of M-Lok\"."},"mlok_diag_slots":{"label":"M-LOK slots on each of the four faces at 45 degrees","kind":"count","measurements":[{"id":"photo","value":8,"unit":"count","source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"none: a count","method":"the light through the upper row (row 701) and the lower row (row 824): eight runs each, the front seven over the side row's seven and one more behind them; eight and eight on the left photo (rows 675 and 798) (m2.py)","via":"harvest"}}]},"mlok_bottom_slots":{"label":"M-LOK slots on its underside (6 o'clock)","kind":"count","measurements":[{"id":"photo","value":7,"unit":"count","source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 270152c59808 (Wing Tactical's gallery for the M-LOK Combat Rail, 57933: a Combat Rail seen from below and behind, its clamp lug near, 1280 x 1280; which of its four lengths isn't stated)","scaleRef":"none: a count","method":"the underside's row, in line with the split of the clamp lug: a short cut, then six long slots in view and the seventh's rear end at the muzzle end, each beside one of the lower face's (whose eighth is likewise at the muzzle end)","via":"harvest"}}],"note":"As the side faces: seven full slots and a short cut behind them, ahead of the clamp lug. Counted on a view of a Combat Rail from below whose length isn't stated; it shows eight slots on the lower faces as this length's level photos do, and the underside's long slots stand beside the lower faces' second to eighth."},"mlok_diag_slot0_from_rear":{"label":"The faces at 45 degrees: their rearmost M-LOK slot (its centre) ahead of the rear face","kind":"length","measurements":[{"id":"photo","value":2.655,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own top rail's 36 slots at the Picatinny pitch (std.picatinny.slot_pitch), each column read as a rail coordinate","method":"the upper row's slots' own ends (the end of each run of light on the lens's side): front ends at S 6.754, 10.752, 14.762, 18.755 and rear ends at 23.556, 27.551, 31.529 once brought to the mid-plane (k 1.0173 from their own spacing): centres at 5.17 + 4n pitches, the rearmost 6.745 pitches ahead of the rail's rear end (m2.py)","via":"harvest"}}]},"mlok_side_slot0_from_rear":{"label":"The side faces' and the underside's rearmost full M-LOK slot (its centre) ahead of the rear face","kind":"length","measurements":[{"id":"photo","value":4.23,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own top rail's 36 slots at the Picatinny pitch (std.picatinny.slot_pitch), each column read as a rail coordinate","method":"the middle row's slots' own ends: front ends at S 6.782, 10.767, 14.781, 18.779 and rear ends at 23.543, 27.544, 31.546 (k 1.021 from their own spacing; the slots 3.24 pitches long for the standard's 3.2): full slots' centres at 9.17 + 4n pitches, the rearmost 10.745 ahead of the rail's rear end. The left photo: rear ends at 19.553, 23.558, 27.557, 31.554 and front ends at 6.801, 10.783, 14.792 (m2.py)","via":"harvest"}}],"note":"One M-LOK pitch (40 mm) ahead of the other faces' rearmost: the rows stand in line, and the side faces and the underside lack the first."},"mlok_diag_slot0_x":{"label":"The faces at 45 degrees: their rearmost M-LOK slot (its centre) ahead of the receiver's front face","kind":"length","measurements":[{"id":"derived","value":2.21,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{.rear_face_x} + {.mlok_diag_slot0_from_rear}","via":"harvest"}}]},"mlok_side_slot0_x":{"label":"The side faces' and the underside's rearmost full M-LOK slot (its centre) ahead of the receiver's front face","kind":"length","measurements":[{"id":"derived","value":3.785,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{.rear_face_x} + {.mlok_side_slot0_from_rear}","via":"harvest"}}]},"short_slot_length":{"label":"The short cut behind the side faces' and the underside's slots, its length","kind":"length","measurements":[{"id":"photo","value":0.64,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own top rail's 36 slots at the Picatinny pitch (std.picatinny.slot_pitch), each column read as a rail coordinate","method":"its front end at S 6.78 (its own edge) and its rear end at 5.17 (the far wall's edge of the light, brought back by k 0.975): 1.61 pitches; the left photo reads 6.83 and 5.15 (m2.py)","via":"harvest"}}],"note":"As wide as an M-LOK slot and about half as long, its front end where an eighth slot's would be (one M-LOK pitch behind the first full slot's). Not offered as a place to mount: no page says what it takes."},"mlok_upper_row_above_bore":{"label":"The upper rows of slots, their middle line above the bore","kind":"length","measurements":[{"id":"photo","value":0.51,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own rail's slots beside the lens's column, 1.7% more at this face's depth: 131.2 px/in","method":"the middle of the light through the upper row (rows 693 to 709: 701), 0.479 above the bore; the light passes a slot cut square through a wall 0.1 in thick at 45 degrees only over its inner 0.125 in of height, so the slot's own middle on the face is 0.035 further from the bore (m2.py)","via":"harvest"}}],"note":"A line from the bore meets an upper face square on 0.53 in above the bore: the row reads 0.02 nearer the side face."},"mlok_lower_row_below_bore":{"label":"The lower rows of slots, their middle line below the bore","kind":"length","measurements":[{"id":"photo","value":0.5,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own rail's slots beside the lens's column, 1.4% more at this face's depth: 130.8 px/in","method":"the middle of the light through the lower row (rows 816 to 833: 824.5), 0.464 below the bore, and 0.035 further for the wall's thickness as on the upper rows (m2.py)","via":"harvest"}}],"note":"A line from the bore meets a lower face square on 0.53 in below the bore: the row reads 0.03 nearer the side face."},"reach_inside":{"label":"The room inside its faces, from a face in to the barrel (what an M-LOK accessory's nuts may take)","kind":"length","measurements":[],"note":"Not sourced: it depends on the barrel and gas block under it, other parts. Its walls are 0.1 in by the maker's two figures (1.5 outside, 1.3 inside)."},"hole_d":{"label":"The round holes through the neck under the rail, their diameter","kind":"length","measurements":[{"id":"photo","value":0.24,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own top rail's 36 slots at the Picatinny pitch (std.picatinny.slot_pitch), each column read as a rail coordinate","method":"the light through the hole at the lens's column: 0.61 pitch long (rows 639 to 669: 31 px tall, the same); 0.613 on the left photo (m2.py)","via":"harvest"}}]},"hole_center_below_top":{"label":"Those holes' centres below the rail's top","kind":"length","measurements":[{"id":"photo","value":0.36,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own rail's slots beside the lens's column, 1% more at the neck's wall: 130.3 px/in","method":"the middle of the light through the holes (row 654), 0.6065 above the principal row, below the rail's top (0.9665 above it) (m2.py)","via":"harvest"}}]},"hole_count":{"label":"Those holes, a side","kind":"count","measurements":[{"id":"photo","value":32,"unit":"count","source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"none: a count","method":"the runs of light along row 654: 32, their middles at S 4.003, 5.000, ... 34.99 (each on a rail slot's centre within 0.02 pitch); 32 on the left photo, on the same slots (m2.py)","via":"harvest"}}],"note":"One under each of the rail's slots from the fifth to the thirty-sixth: none under the first four, where the neck carries the maker's marks."},"hole0_from_rail_slot0":{"label":"The rearmost of those holes ahead of the rail's rearmost slot","kind":"length","measurements":[{"id":"photo","value":1.576,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own top rail's 36 slots at the Picatinny pitch (std.picatinny.slot_pitch), each column read as a rail coordinate","method":"the rearmost hole's light, its middle at S 4.003: under the rail's fifth slot (m2.py)","via":"harvest"}}]},"socket_from_rear":{"label":"The sling sockets (their centres) ahead of the rear face","kind":"length","measurements":[{"id":"photo","value":1.9,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own top rail's 36 slots at the Picatinny pitch (std.picatinny.slot_pitch), each column read as a rail coordinate","method":"the socket's round hole, its centre at px (375, 762) on a 3x crop: S 3.24 at k 1.021, 4.81 pitches ahead of the rail's rear end; the left photo reads S 3.26 (px 1816, where light shows through both sockets) (m2.py)","via":"harvest"}}],"note":"The maker: \"Two Integral Anti-Rotation QD Sling Sockets\". One in each side face, on the line of the side rows of slots, in a shallow flat cut across the face."},"socket_d":{"label":"A sling socket's hole, its diameter","kind":"length","measurements":[{"id":"photo","value":0.365,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own rail's slots at the rear end (49.35 px a pitch), 2.1% more on the near side face: 128 px/in","method":"the dark round hole, 46.7 px across on a 3x crop","via":"harvest"}}]},"socket_recess_length":{"label":"The flat cut across each side face round its sling socket, its length","kind":"length","measurements":[{"id":"photo","value":0.62,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own top rail's 36 slots at the Picatinny pitch (std.picatinny.slot_pitch), each column read as a rail coordinate","method":"the cut's two ends at px 333 and 413 on a 3x crop: S 2.40 and 3.99 at k 1.021","via":"harvest"}}],"note":"Between the plain panel at the rear end and the first slots the side face is cut a little lower over the whole of its height, the socket in the middle of the cut, its two ends sloped."},"socket_recess_depth":{"label":"That cut's depth below the side face","kind":"length","measurements":[{"id":"photo","value":0.035,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own rail's slots at the rear end, on the near side face: 128 px/in","method":"the upper crease 3 to 5 px lower over the cut than on the panel behind it, on a 3x crop","via":"harvest"}}],"note":"Weakly read: by how far the side face's two creases step toward each other where the cut is (a cut into a face between two faces at 45 degrees moves each crease by its own depth)."},"pocket_diag_from_rear":{"label":"The blind pocket at the rear of each face at 45 degrees (its centre) ahead of the rear face","kind":"length","measurements":[{"id":"photo","value":1.1,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own top rail's 36 slots at the Picatinny pitch (std.picatinny.slot_pitch), each column read as a rail coordinate","method":"the upper face's pocket from px 196.7 to 358.3 on a 3x crop: S -0.386 to 2.834 at k 1.0167, its middle 2.80 pitches ahead of the rail's rear end; the lower face's pocket stands at the same columns","via":"harvest"}}],"note":"Where a ninth slot would be, one M-LOK pitch behind the rearmost, each face at 45 degrees has a shallow pocket of a slot's length that doesn't go through. The side faces have a shorter one with the maker's mark in it (pocket_side_from_rear)."},"pocket_diag_length":{"label":"That pocket's length","kind":"length","measurements":[{"id":"photo","value":1.27,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own top rail's 36 slots at the Picatinny pitch (std.picatinny.slot_pitch), each column read as a rail coordinate","method":"S -0.386 to 2.834: 3.22 pitches (an M-LOK slot is 3.2)","via":"harvest"}}]},"pocket_diag_width":{"label":"That pocket's width on its face","kind":"length","measurements":[{"id":"photo","value":0.33,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own rail's slots at the rear end, 1.7% more at this face's depth: 129.6 px/in","method":"30 px tall on the level photo (rows 681.7 to 711.7), the face seen at 45 degrees","via":"harvest"}}]},"pocket_side_from_rear":{"label":"The blind pocket at the rear of each side face (its centre) ahead of the rear face","kind":"length","measurements":[{"id":"photo","value":0.815,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own top rail's 36 slots at the Picatinny pitch (std.picatinny.slot_pitch), each column read as a rail coordinate","method":"the pocket with the maker's mark from px 191.7 to 281.7 on a 3x crop: S -0.398 to 1.39 at k 1.021, its middle 2.07 pitches ahead of the rail's rear end, on the line of the side rows of slots (rows 745 to 781.7)","via":"harvest"}}]},"pocket_side_length":{"label":"That pocket's length","kind":"length","measurements":[{"id":"photo","value":0.7,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own top rail's 36 slots at the Picatinny pitch (std.picatinny.slot_pitch), each column read as a rail coordinate","method":"S -0.398 to 1.39: 1.79 pitches","via":"harvest"}}]},"pocket_side_width":{"label":"That pocket's width (up and down the side face)","kind":"length","measurements":[{"id":"photo","value":0.28,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own rail's slots at the rear end, 2.1% more on the near side face: 130.2 px/in","method":"rows 745 to 781.7: 36.7 px (an M-LOK slot's width)","via":"harvest"}}]},"pocket_depth":{"label":"Those pockets' depth","kind":"length","measurements":[{"id":"rear-view","value":0.02,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard a8877c4d13c1 (the maker's gallery, MI-CRM4.5-2: the 4.5 in Combat Rail seen from its right and behind, 883 x 697)","scaleRef":"its own rail's slots in that view: about 178 px/in along it","method":"the lit wall along the upper edge of each pocket, 1.5 to 2 px wide seen from about 45 degrees: 0.01 to 0.03 in","via":"harvest"},"note":"The rear end is the same on every length of this handguard."}],"note":"Weakly read: the pockets' walls show as a line a pixel or two wide in every oblique view; nothing on file measures them. Shallow against a wall of 0.1 in."},"scallop_length":{"label":"The small scallops along the side faces' and the bottom's edges, each one's length","kind":"length","measurements":[{"id":"photo","value":0.22,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own rail's slots at the muzzle end, 2.1% more on the near side face: 129.6 px/in","method":"each scallop 27 to 33 px long on a 3x crop of the muzzle end","via":"harvest"}}],"note":"A shallow round-bottomed cut across each crease every 20 mm (half an M-LOK pitch), at the slots' middles and at the bars between them, from the first slot of the faces at 45 degrees to the muzzle end: sixteen by those stations. Read at the two ends of the row (S 5.3 and 7.3 on a crop of the rear end; 29.2 to 35.2 on one of the muzzle end); the ones between are seen at the same spacing and not each measured."},"scallop_height":{"label":"Each scallop's reach into the side face from its edge","kind":"length","measurements":[{"id":"photo","value":0.03,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own rail's slots at the muzzle end, 2.1% more on the near side face: 129.6 px/in","method":"each scallop 4 px tall on the side face on a 3x crop of the muzzle end","via":"harvest"}}]},"scallop_count":{"label":"Scallops along each crease","kind":"count","measurements":[{"id":"photo","value":16,"unit":"count","source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"none: a count by stations","method":"one every two rail pitches from S 5.17 (seen at 5.3 and 7.3 on the rear end's crop, uncorrected for depth) to S 35.17 (seen at 29.2, 31.2, 33.2 and 35.2 on the muzzle end's): sixteen stations","via":"harvest"}}]},"lug_bottom_below_bore":{"label":"The clamp lug under the rear end, its bottom below the bore","kind":"length","measurements":[{"id":"photo","value":1.135,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own rail's slots at the rear end, the lens's bend taken across the rifle at a third of what it is along it: 128.4 px/in","method":"the lug's bottom edge (row 908) below the bore's row there (762.7): 145.3 px, 1.132; the left photo: 146.5 px, 1.141 (m4.py)","via":"harvest"}}],"note":"A block under the bottom flat at the rear end, split along its middle, drawn together round the barrel nut by the two clamp screws."},"height_over_lug":{"label":"Height over all, the rail's top to the clamp lug's bottom","kind":"length","measurements":[{"id":"derived","value":2.355,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.rail_top_above_bore} + {.lug_bottom_below_bore}","via":"harvest"}}],"note":"What the level side outline's height is scaled by: the published height carried down to the lug by the photo's own reading of it."},"lug_corner_r":{"label":"The lug's rear lower corner, its round","kind":"length","measurements":[{"id":"photo","value":0.13,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own rail's slots at the rear end: 128.4 px/in","method":"the lug's rear edge leaves its line at row 889 and its bottom edge begins at px 170, 17 px on from the rear edge (px 153) and 18 px down (m4.py)","via":"harvest"}}]},"lug_flat_from_rear":{"label":"The lug's flat underside, its front end ahead of the rear face","kind":"length","measurements":[{"id":"photo","value":1.24,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own top rail's 36 slots at the Picatinny pitch (std.picatinny.slot_pitch), each column read as a rail coordinate","method":"where the lug's bottom edge begins to rise (px 307; 313.9 in the mid-plane) ahead of the rail's rear end (155.1): 1.270 in; the left photo reads 1.216 (m4.py)","via":"harvest"}}]},"lug_ramp_from_rear":{"label":"The lug's front ramp, where it meets the bottom flat, ahead of the rear face","kind":"length","measurements":[{"id":"photo","value":1.64,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own top rail's 36 slots at the Picatinny pitch (std.picatinny.slot_pitch), each column read as a rail coordinate","method":"where the ramp reaches the tube's bottom edge (px 355; 361.6 in the mid-plane): 1.651 in ahead of the rail's rear end; the left photo reads 1.632 (m4.py)","via":"harvest"}}]},"lug_width":{"label":"The lug's width (across its two halves)","kind":"length","measurements":[{"id":"rear-view","value":0.51,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 373fa3ba37aa (Wing Tactical's gallery for the M-LOK Combat Rail, 58126: a Combat Rail seen from behind and its right, the rear end near, 1280 x 1280; which of its four lengths isn't stated)","scaleRef":"the body's width on its rear face (this ledger's width over 590 px on a 3.5x crop)","method":"the lug's rear face under the barrel nut, about 200 px across its two halves","via":"harvest"},"note":"The rear end is the same on every length of this handguard."}],"note":"About the bottom flat's own width (0.48 in between its broken corners on a regular octagon 1.5 in across), and what a 10-32 x 1/2 screw's half inch of thread has to cross."},"clamp_gap_width":{"label":"The split along the lug's underside, its width","kind":"length","measurements":[{"id":"rear-view","value":0.08,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 373fa3ba37aa (Wing Tactical's gallery for the M-LOK Combat Rail, 58126: a Combat Rail seen from behind and its right, the rear end near, 1280 x 1280; which of its four lengths isn't stated)","scaleRef":"the body's width on its rear face (this ledger's width over 590 px on a 3.5x crop)","method":"the dark gap in the middle of the lug's rear face, about 30 px wide","via":"harvest"},"note":"The rear end is the same on every length of this handguard."}],"note":"The torque plate stands in it (the maker's sheet: \"Drop the torque plate into the slot in the handguard\")."},"screw_rear_from_rear":{"label":"The rear clamp screw (its axis) ahead of the rear face","kind":"length","measurements":[{"id":"photo","value":0.427,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own top rail's 36 slots at the Picatinny pitch (std.picatinny.slot_pitch), each column read as a rail coordinate","method":"the rear head's centre (px 198.3 on a 3x crop) as S -0.497 at k 1.01, 1.078 pitches ahead of the rail's rear end: 0.424; the left photo's rear hole reads 0.429 (m4.py)","via":"harvest"}}],"note":"The maker's sheet: \"the (2) 10-32 x ½” socket head cap screws from the rear of the handguard\". Their heads stand on the lug's right side; their ends show in two holes on its left."},"screw_front_from_rear":{"label":"The front clamp screw (its axis) ahead of the rear face","kind":"length","measurements":[{"id":"photo","value":0.985,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own top rail's 36 slots at the Picatinny pitch (std.picatinny.slot_pitch), each column read as a rail coordinate","method":"the front head's centre (px 268.3 on a 3x crop) as S 0.915 at k 1.01: 0.980; the left photo's front hole reads 0.990. The two are 0.556 and 0.561 apart (m4.py)","via":"harvest"}}]},"screw_below_bore":{"label":"The clamp screws' axes below the bore","kind":"length","measurements":[{"id":"photo","value":0.887,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own rail's slots at the rear end: 128.4 px/in","method":"the two heads' centres (rows 876.7 and 875) below the bore's row there (762.7): 0.881; the left photo's two holes, 0.893 (m4.py)","via":"harvest"}}]},"screw_d":{"label":"A clamp screw's shank, its diameter","kind":"length","measurements":[{"id":"photo","value":0.19,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard e1fb6c9b2da4 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_02.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","scaleRef":"its own rail's slots at the rear end: 126.2 px/in","method":"each screw's end in its hole on the lug's left side: the hole 28 px across with its broken edge, the screw's end inside it 22 to 25 px, on a 3.5x crop","via":"harvest"}}],"note":"The maker names the screws 10-32 (a No. 10 thread). Read on the photo, not taken from a thread table."},"screw_length":{"label":"A clamp screw's length under its head","kind":"length","measurements":[{"id":"maker","value":0.5,"unit":"in","pm":0.03,"stated":"(2) 10-32 x ½” socket head cap screws","source":{"type":"spec","publisher":"manufacturer","name":"Midwest Industries, Free Float Hand Guard Installation Instructions (one page), step 8","url":"https://midwestindustriesinc.com/content/installation-instructions/AR15-Free-Float-Handguard-Instructions.pdf","retrieved":"2026-10-12","via":"harvest"}}]},"screw_head_d":{"label":"A clamp screw's head, its diameter","kind":"length","measurements":[{"id":"photo","value":0.31,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own rail's slots at the rear end: 128.4 px/in","method":"each head 40 px across on a 3x crop","via":"harvest"}}]},"screw_head_height":{"label":"A clamp screw's head, how far it stands off the lug's right side","kind":"length","measurements":[{"id":"below","value":0.17,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 270152c59808 (Wing Tactical's gallery for the M-LOK Combat Rail, 57933: a Combat Rail seen from below and behind, its clamp lug near, 1280 x 1280; which of its four lengths isn't stated)","scaleRef":"each head's own diameter in that view (this ledger's screw_head_d)","method":"each head stands a half to six tenths of its diameter off the lug on a 7x crop","via":"harvest"},"note":"The rear end is the same on every length of this handguard."}]},"screw_socket_w":{"label":"A clamp screw's hexagon socket, across its flats","kind":"length","measurements":[{"id":"photo","value":0.155,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","scaleRef":"its own rail's slots at the rear end: 128.4 px/in","method":"the dark hexagon in each head, 19 to 20 px across on a 3x crop (half the head's 40)","via":"harvest"}}]},"nut_od":{"label":"Its barrel nut, its outside diameter (the round bore at the handguard's rear end)","kind":"length","measurements":[{"id":"hardware","value":1.345,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 47ebce89cf02 (the maker's gallery, MI-CRM7-2: the 7 in Combat Rail with its barrel nut, torque plate, wrench, polymer rail and keys laid out, 1192 x 980)","scaleRef":"the receiver's barrel-nut thread, its minor diameter (bcm-m4-upper.thread_minor_d: 1.1803 in), which the nut's thread crests stand on","method":"the nut's rim, its long axis 760 px on a 3x crop, the ring between the knurl and the thread's crests about 45 px wide each side: the crests' circle 0.88 of the outside, 1.341 in; 0.865 to 0.895 by a few pixels either way","via":"harvest"},"note":"One nut for every length (the maker's pictures show the same one with each)."},{"id":"rear-view","value":1.41,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 373fa3ba37aa (Wing Tactical's gallery for the M-LOK Combat Rail, 58126: a Combat Rail seen from behind and its right, the rear end near, 1280 x 1280; which of its four lengths isn't stated)","scaleRef":"the body's width on its rear face (this ledger's width over 590 px on a 3.5x crop)","method":"the nut's rim, 555 px across, in a view from the side of the rear face: the two aren't in one plane (the nut stands a little proud) and the body's far edge is hidden","via":"harvest"},"note":"The rear end is the same on every length of this handguard."}],"adopt":{"from":"hardware","reason":"A ratio on the nut itself, seen nearly end on, over a thread the Army's drawing sizes; the oblique view of the rear end reads 0.065 more, which would leave 0.045 in of wall at the side faces and stand in the gas tube's way (its underside is 0.69 in above the bore by std.ar15.gas_tube_above_bore and a tube's 0.18; the maker's nut needs \"no timing\", Primary Arms, so the tube passes over it)."},"note":"The nut fills the rear end's round bore, which is larger than the 1.3 in the maker gives for the inside: the walls are thinnest there. Read as a ratio on the nut laid out beside the handguard: its rim, between the knurl and the crests of its thread, is 0.06 of its diameter wide, and those crests stand on the receiver thread's minor diameter (bcm-m4-upper.thread_minor_d, the Army's 1¼-18)."},"nut_bore":{"label":"Its barrel nut's threaded bore (the receiver thread it goes over)","kind":"length","measurements":[{"id":"derived","value":1.244,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{bcm-m4-upper.thread_major_d}","via":"harvest"}}],"note":"The maker's sheet: \"Screw the barrel nut onto the upper receiver threads\". Taken as the receiver thread's major diameter (the Army's 1¼-18 UNEF, 1.244 in after anodize: bcm-m4-upper.thread_major_d), which is what the nut has to go over and what its ring is drawn round; its own thread's crests stand inside that (nut_od's reading)."},"nut_length":{"label":"Its barrel nut's length","kind":"length","measurements":[{"id":"hardware","value":1.12,"unit":"in","pm":0.1,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 47ebce89cf02 (the maker's gallery, MI-CRM7-2: the 7 in Combat Rail with its barrel nut, torque plate, wrench, polymer rail and keys laid out, 1192 x 980)","scaleRef":"the nut's own outside diameter in that view (this ledger's nut_od over 760 px)","method":"the nut seen with its axis 38 degrees off the line of sight (its rim's short axis 0.79 of the long one): its two rims' centres 387 px apart, 628 px along the axis: 0.83 of its diameter","via":"harvest"},"note":"One nut for every length."}]},"plate_length":{"label":"Its torque plate, its length","kind":"length","measurements":[{"id":"hardware","value":1,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 47ebce89cf02 (the maker's gallery, MI-CRM7-2: the 7 in Combat Rail with its barrel nut, torque plate, wrench, polymer rail and keys laid out, 1192 x 980)","scaleRef":"its two holes' centres (the clamp screws' spacing, 0.558 in by this ledger, over 295 px on a 3x crop)","method":"the plate 530 px long","via":"harvest"},"note":"One plate for every length."}],"note":"A flat steel plate with two holes for the clamp screws and a round post on its upper edge, which stands in the split of the lug with the post in the groove round the barrel nut."},"plate_height":{"label":"Its torque plate, its height without the post","kind":"length","measurements":[{"id":"hardware","value":0.36,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 47ebce89cf02 (the maker's gallery, MI-CRM7-2: the 7 in Combat Rail with its barrel nut, torque plate, wrench, polymer rail and keys laid out, 1192 x 980)","scaleRef":"its two holes' centres (0.558 in over 295 px on a 3x crop)","method":"the plate 190 px tall","via":"harvest"},"note":"One plate for every length."}]},"plate_thickness":{"label":"Its torque plate, its thickness","kind":"length","measurements":[{"id":"hardware","value":0.06,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/midwest-combat-rail-15-handguard 47ebce89cf02 (the maker's gallery, MI-CRM7-2: the 7 in Combat Rail with its barrel nut, torque plate, wrench, polymer rail and keys laid out, 1192 x 980)","scaleRef":"its two holes' centres (0.558 in over 295 px on a 3x crop)","method":"the plate's lower edge, 25 to 35 px thick seen a little from below; inside the lug's split (clamp_gap_width)","via":"harvest"},"note":"One plate for every length."}]}}},{"subject":"midwest-industries-drop-in-mlok-carbine","title":"Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Carbine, MI-17M)","dimensions":{"weight":{"label":"Weight (installed: both halves)","kind":"mass","measurements":[{"id":"maker","value":5,"unit":"oz","pm":0.05,"stated":"Installed Weight [...] Carbine - 5.0oz","source":{"type":"spec","publisher":"manufacturer","name":"Midwest Industries, AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (SKU AR15M16TWOPI; Length: Carbine, MI-17M), Product Details","url":"https://www.midwestindustriesinc.com/product-p/mi-17m-blk.htm","retrieved":"2026-10-28","via":"harvest"}}],"note":"The maker's table is headed \"Installed Weight\": the two halves as they go on the rifle. The short M-LOK rail section in its picture isn't weighed in it as far as the page says."},"length":{"label":"Length (the maker's overall length; read here as the rail's whole length, its tongue's rear end to its front)","kind":"length","measurements":[{"id":"maker","value":7,"unit":"in","stated":"Overall Length [...] MI-17M - 7\"","source":{"type":"spec","publisher":"manufacturer","name":"Midwest Industries, AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (SKU AR15M16TWOPI; Length: Carbine, MI-17M), Product Details","url":"https://www.midwestindustriesinc.com/product-p/mi-17m-blk.htm","retrieved":"2026-10-28","via":"harvest"}},{"id":"photo","value":7.09,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-carbine b73705e19a54 (the maker's gallery picture MI-17M-BLK-2: the carbine length alone, from behind its right side and above, muzzle to the right, with a short M-LOK rail section beside it, 1200 x 566)","scaleRef":"a pinhole camera fitted to the rail's 15 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's three M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.33 px, max 4.8 px, f 3984 px, the lens 23.0 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py, cam_carbine.json)","method":"the tongue's rear end (1.06 behind slot 0: tongue_rear_from_slot0) to the rail's and the upper half's front (6.03 ahead: front_from_slot0)","via":"harvest"}}],"adopt":{"from":"maker","reason":"The maker's figure, which its photo through its camera reads 0.09 more of, inside the figure's half digit."}},"mounting_length":{"label":"Its mounting length: from its rear flanges' end (on the delta ring's lip) to the end of what goes into the cap (at the inside of the cap's face)","kind":"length","measurements":[{"id":"room","value":6.5,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the room the catalog's carbine-length rifle holds it in: from the delta ring's lip (std.ar15.slip_ring_front_x, 0.336 ahead of the receiver's face) to the round cap's pocket, the inside of its face (bcm-handguard-cap-round-750, its sheet behind its seat), with the cap on BCM's F base on bcm-115-carbine-barrel (the base's rear face 6.868 ahead of the receiver's face): 6.500.","via":"harvest"}}],"note":"A part held between two faces is as long as the room it is held in (CLAUDE.md, the P90 magazine): the cap seats it there (D97, ar15.handguard_front). Not seen in the photo: what of its front goes into the cap is inside its front end. The maker's 7 in is another span, the rail's whole length (length: 7.09 by the photo)."},"base_rear_x":{"label":"The front sight base's rear face (the cap's seat), in its frame, with the cap seating it: its mounting length and the cap's face ahead of its rear end","kind":"length","measurements":[{"id":"derived","value":6.868,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.rear_x} + {.mounting_length} + {bcm-handguard-cap-round-750.sheet}","via":"harvest"}}],"note":"What of its hidden front stands in the base's space ahead of this face is cut from its inside (pipeline/blender/midwest_industries_drop_in_mlok_mid.py): the base is sourced, its inside isn't."},"overall_length":{"label":"Its whole length, from its rear flanges' end (in the delta ring) to the lower half's front edge","kind":"length","measurements":[{"id":"photo","value":6.84,"unit":"in","pm":0.07,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-carbine b73705e19a54 (the maker's gallery picture MI-17M-BLK-2: the carbine length alone, from behind its right side and above, muzzle to the right, with a short M-LOK rail section beside it, 1200 x 566)","scaleRef":"a pinhole camera fitted to the rail's 15 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's three M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.33 px, max 4.8 px, f 3984 px, the lens 23.0 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py, cam_carbine.json)","method":"the rear flanges' rim at 0.70 behind the rail's slot 0 (rail_slot0_from_rear) to the lower half's front edge at 6.14 (lower_front_from_slot0)","via":"harvest"}}]},"width":{"label":"Width (across the lower half's side faces)","kind":"length","measurements":[{"id":"maker","value":1.83,"unit":"in","pm":0.005,"stated":"1.83\" wide and 2.25\" tall","source":{"type":"spec","publisher":"manufacturer","name":"Midwest Industries, AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (SKU AR15M16TWOPI; Length: Carbine, MI-17M), Product Details","url":"https://www.midwestindustriesinc.com/product-p/mi-17m-blk.htm","retrieved":"2026-10-28","via":"harvest"}}],"note":"One figure for the three lengths. Taken as across the lower half's flat side faces, the widest in the photo (the camera's plane for the M-LOK slots)."},"height":{"label":"Height (the rail's top to the bottom)","kind":"length","measurements":[{"id":"maker","value":2.25,"unit":"in","pm":0.005,"stated":"1.83\" wide and 2.25\" tall","source":{"type":"spec","publisher":"manufacturer","name":"Midwest Industries, AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (SKU AR15M16TWOPI; Length: Carbine, MI-17M), Product Details","url":"https://www.midwestindustriesinc.com/product-p/mi-17m-blk.htm","retrieved":"2026-10-28","via":"harvest"}},{"id":"photo","value":2.28,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-carbine b73705e19a54 (the maker's gallery picture MI-17M-BLK-2: the carbine length alone, from behind its right side and above, muzzle to the right, with a short M-LOK rail section beside it, 1200 x 566)","scaleRef":"a pinhole camera fitted to the rail's 15 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's three M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.33 px, max 4.8 px, f 3984 px, the lens 23.0 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py, cam_carbine.json)","method":"the bottom's silhouette at column 745 (row 427) carried back onto z = 0.415: 2.283 below the rail's top","via":"harvest"}}],"adopt":{"from":"maker","reason":"The maker's figure; the camera, fitted to no height but the M-LOK slots' 7 mm, reads 0.03 more."}},"inside_diameter":{"label":"Inside diameter","kind":"length","measurements":[],"note":"Not published, and no view on file looks into either end square on. Left missing: the model's inside is its wall (assumed) inside its section."},"rear_x":{"label":"Its rear end (the rear flanges' end, bearing on the delta ring's lip) ahead of the receiver's front face","kind":"length","measurements":[{"id":"derived","value":0.336,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{std.ar15.slip_ring_front_x}","via":"harvest"}}],"note":"Where the standard's delta ring holds it: its rear flanges in the ring's skirt, against the lip (std.ar15.slip_ring_front_x). Its instructions: \"Pull the delta ring to the rear and remove both sections of the plastic handguards, pulling out from the delta ring end first.\""},"rail_top_above_bore":{"label":"Its rail's top above the bore axis","kind":"length","measurements":[{"id":"level","value":1.2125,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{bcm-m4-upper.rail_top_above_pin} - {bcm-m4-upper.bore_axis_above_pin}","via":"harvest"}}],"note":"Level with a mil-spec receiver's rail: the maker's \"Monolithic type continuous top rail\". So the catalog's BCM M4 upper's rail top above its pin line less its bore's height above it."},"rail_slots":{"label":"Slots in its top rail","kind":"count","measurements":[{"id":"photo","value":15,"unit":"count","source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-carbine b73705e19a54 (the maker's gallery picture MI-17M-BLK-2: the carbine length alone, from behind its right side and above, muzzle to the right, with a short M-LOK rail section beside it, 1200 x 566)","scaleRef":"none: a count","method":"the top silhouette's dips under the lands' envelope (dips.py): 15, centres from px 184.8 to 1002.2, each 53.4 to 64.6 px from the next, falling smoothly with the distance (a projective map through them leaves 0.28 px rms), none missing; the first is the slot between the tongue's front (px 161) and the first land (px 194), at the pitch of the rest","via":"harvest"}}]},"rail_slot0_from_rear":{"label":"Its rail's rearmost slot (its centre) ahead of its rear end (the rear flanges' end)","kind":"length","measurements":[{"id":"photo","value":0.7,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-carbine b73705e19a54 (the maker's gallery picture MI-17M-BLK-2: the carbine length alone, from behind its right side and above, muzzle to the right, with a short M-LOK rail section beside it, 1200 x 566)","scaleRef":"a pinhole camera fitted to the rail's 15 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's three M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.33 px, max 4.8 px, f 3984 px, the lens 23.0 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py, cam_carbine.json)","method":"the flanges' rear rim: circles of their radius (collar_od) about the bore axis carried through the camera at 0.6 to 1.2 behind slot 0 over the photo (rim.py, rim_carbine.png): both flanges' outer edges lie between the ones at 0.6 and 0.8","via":"harvest"}}]},"rail_slot0_x":{"label":"Its rail's rearmost slot (its centre) ahead of the receiver's front face","kind":"length","measurements":[{"id":"derived","value":1.036,"unit":"in","pm":0.075,"source":{"type":"derived","expr":"{.rear_x} + {.rail_slot0_from_rear}","via":"harvest"}}]},"tongue_rear_from_slot0":{"label":"The rail's tongue (its plain rear part over the delta ring), its rear end behind the rail's slot 0","kind":"length","measurements":[{"id":"photo","value":1.06,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-carbine b73705e19a54 (the maker's gallery picture MI-17M-BLK-2: the carbine length alone, from behind its right side and above, muzzle to the right, with a short M-LOK rail section beside it, 1200 x 566)","scaleRef":"a pinhole camera fitted to the rail's 15 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's three M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.33 px, max 4.8 px, f 3984 px, the lens 23.0 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py, cam_carbine.json)","method":"the tongue's far rear corner (column 13.5, row 108.8) on the top flat's far edge: 1.051 behind slot 0 through the camera, 1.069 on the top's plane","via":"harvest"}}],"note":"With its rear flanges in the delta ring (rear_x, rail_slot0_from_rear) this puts the tongue's rear end 0.02 in behind the upper receiver's front face, inside the two readings' ± (0.04 and 0.06): it reaches the receiver, the maker's \"continuous top rail\". Drawn bearing on the receiver's front face."},"tongue_thickness":{"label":"The rail's tongue's thickness (a plate under the rail's top)","kind":"length","measurements":[{"id":"assumed","value":0.12,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the photo shows the plate's far rear edge 12 to 15 px tall from 23 in, edge-on from above where it isn't a height that can be read. Its underside stands 0.13 over the delta ring's front land (std.ar15.slip_ring_front_od) under a rail level with the receiver's.","via":"harvest"}}]},"front_from_slot0":{"label":"The upper half's front (the rail's front end) ahead of the rail's slot 0","kind":"length","measurements":[{"id":"photo","value":6.03,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-carbine b73705e19a54 (the maker's gallery picture MI-17M-BLK-2: the carbine length alone, from behind its right side and above, muzzle to the right, with a short M-LOK rail section beside it, 1200 x 566)","scaleRef":"a pinhole camera fitted to the rail's 15 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's three M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.33 px, max 4.8 px, f 3984 px, the lens 23.0 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py, cam_carbine.json)","method":"the last land's front by the lands' projective map (fit1d.py), 6.015; the upper side face's front edge carried back onto its plane at the holes' height, 6.06","via":"harvest"}}]},"upper_rear_from_slot0":{"label":"The upper half's body's rear face behind the rail's slot 0","kind":"length","measurements":[{"id":"photo","value":0.336,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-carbine b73705e19a54 (the maker's gallery picture MI-17M-BLK-2: the carbine length alone, from behind its right side and above, muzzle to the right, with a short M-LOK rail section beside it, 1200 x 566)","scaleRef":"a pinhole camera fitted to the rail's 15 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's three M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.33 px, max 4.8 px, f 3984 px, the lens 23.0 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py, cam_carbine.json)","method":"the upper side face's rear edge (column 205, row 250) carried back onto its plane (z 0.85)","via":"harvest"}}]},"lower_rear_from_slot0":{"label":"The lower half's body's rear face behind the rail's slot 0","kind":"length","measurements":[{"id":"photo","value":0.245,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-carbine b73705e19a54 (the maker's gallery picture MI-17M-BLK-2: the carbine length alone, from behind its right side and above, muzzle to the right, with a short M-LOK rail section beside it, 1200 x 566)","scaleRef":"a pinhole camera fitted to the rail's 15 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's three M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.33 px, max 4.8 px, f 3984 px, the lens 23.0 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py, cam_carbine.json)","method":"the lower side face's rear edge carried back onto its plane at two heights: 0.239 and 0.252 behind slot 0","via":"harvest"}}]},"lower_front_from_slot0":{"label":"The lower half's front edge ahead of the rail's slot 0","kind":"length","measurements":[{"id":"photo","value":6.14,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-carbine b73705e19a54 (the maker's gallery picture MI-17M-BLK-2: the carbine length alone, from behind its right side and above, muzzle to the right, with a short M-LOK rail section beside it, 1200 x 566)","scaleRef":"a pinhole camera fitted to the rail's 15 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's three M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.33 px, max 4.8 px, f 3984 px, the lens 23.0 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py, cam_carbine.json)","method":"the lower side face's front edge (column 1184, row 250) carried back onto its plane: 6.138","via":"harvest"}}]},"bottom_cut_from_slot0":{"label":"Where the bottom flat ends at the front (its front part cut up), ahead of the rail's slot 0","kind":"length","measurements":[{"id":"photo","value":5.95,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-carbine b73705e19a54 (the maker's gallery picture MI-17M-BLK-2: the carbine length alone, from behind its right side and above, muzzle to the right, with a short M-LOK rail section beside it, 1200 x 566)","scaleRef":"a pinhole camera fitted to the rail's 15 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's three M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.33 px, max 4.8 px, f 3984 px, the lens 23.0 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py, cam_carbine.json)","method":"the bottom's step at columns 1086 to 1100 (rows 345 to 366) carried back onto the bottom's plane (y = -2.25): 5.86 to 5.96","via":"harvest"}}]},"bottom_cut_height":{"label":"How far the bottom's front part is cut up","kind":"length","measurements":[{"id":"assumed","value":0.12,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the step shows about 20 px tall in the photo, edge-on from above, where it isn't a height that can be read.","via":"harvest"}}]},"neck_foot_below_top":{"label":"The rail's neck's foot (where the upper half's top, a shelf out to its side faces, meets the neck under the head) below the rail's top","kind":"length","measurements":[{"id":"neck","value":0.41,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-carbine b73705e19a54 (the maker's gallery picture MI-17M-BLK-2: the carbine length alone, from behind its right side and above, muzzle to the right, with a short M-LOK rail section beside it, 1200 x 566)","scaleRef":"a pinhole camera fitted to the rail's 15 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's three M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.33 px, max 4.8 px, f 3984 px, the lens 23.0 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py, cam_carbine.json)","method":"the dark line under the engraved face (column 745, rows 127 to 130) carried back onto a plane at z 0.343 (the neck's side is at 0.363, the head's lower faces carried on to shoulder_top_below_top: a thousandth of difference here): 0.407 to 0.419","via":"harvest"}},{"id":"side","value":0.268,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-carbine b73705e19a54 (the maker's gallery picture MI-17M-BLK-2: the carbine length alone, from behind its right side and above, muzzle to the right, with a short M-LOK rail section beside it, 1200 x 566)","scaleRef":"a pinhole camera fitted to the rail's 15 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's three M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.33 px, max 4.8 px, f 3984 px, the lens 23.0 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py, cam_carbine.json)","method":"the same line carried back onto the upper side face's plane (z 0.85) instead","via":"harvest"}}],"adopt":{"from":"neck","reason":"One line of the photo, read on two planes; which one it lies in the photo can't say. Read on the side face's plane (the first reading, a sloped shoulder from the neck out to the side faces under it), the body stood 0.18 to 0.19 in under the rail's top beside the head, and 17 of the 30 clamps on file stood in it (Aimpoint's T-2 LRP 0.06 cubic inches, its PRO and Duty RDS, EOTECH's STS, SIG's Romeo5, Holosun's ARO and HS510C, Magpul's MBUS 3: rail-clamps.test.ts); on the maker's \\\"MIL-STD 1913 top rail\\\" they go. Read on the neck's plane, the engraved face is the neck's side, as the maker engraves its name under the rail on its Combat Rail's neck (0.69 in wide down to 0.56 under its top: midwest-combat-rail-15-handguard), and a forged upper's neck runs as deep (0.39); the line read at column 760, row 140 as a hole's top rim (0.351 on the side face's plane) is the shelf's outer edge, 0.41 down. Drawn so: a neck down to here, the shelf out to the side faces."}},"shoulder_top_below_top":{"label":"The neck's top: where the head's lower faces, carried on at 45 degrees, meet the neck's sides, below the rail's top","kind":"length","measurements":[{"id":"photo","value":0.18,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-carbine b73705e19a54 (the maker's gallery picture MI-17M-BLK-2: the carbine length alone, from behind its right side and above, muzzle to the right, with a short M-LOK rail section beside it, 1200 x 566)","scaleRef":"a pinhole camera fitted to the rail's 15 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's three M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.33 px, max 4.8 px, f 3984 px, the lens 23.0 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py, cam_carbine.json)","method":"the top of the dark band under the lands (column 745, row 91: the head's lower faces and the neck's top in their shadow) carried back onto the neck's plane (z 0.343): 0.18. (First read as the top of a shoulder sloping out from the head, on a plane at z 0.6; with the engraved face taken for the neck's side, it is this.)","via":"harvest"}}],"note":"With the standard's head (lib.rail_half) this sets the neck's half width: the head's lower faces carried on to here."},"upper_half_width":{"label":"Width across the upper half's side faces","kind":"length","measurements":[{"id":"assumed","value":1.7,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the photo shows the lower half's top as a ledge outside the upper half's side; how far isn't read from a view from above. Every reading on the upper side face is carried back onto this plane.","via":"harvest"}}]},"channel_roof_below_top":{"label":"The gas tube's channel up inside the neck: its roof below the rail's top","kind":"length","measurements":[{"id":"assumed","value":0.15,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view looks into either end. The neck stands over the gas tube (std.ar15.gas_tube_above_bore), so it is hollow up to a web under the rail's slots' floors (std.picatinny.slot_depth, 0.118), as thick as a few hundredths.","via":"harvest"}}]},"seam_below_top":{"label":"The upper side face's lower edge (the seam between the halves) below the rail's top","kind":"length","measurements":[{"id":"photo","value":0.979,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-carbine b73705e19a54 (the maker's gallery picture MI-17M-BLK-2: the carbine length alone, from behind its right side and above, muzzle to the right, with a short M-LOK rail section beside it, 1200 x 566)","scaleRef":"a pinhole camera fitted to the rail's 15 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's three M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.33 px, max 4.8 px, f 3984 px, the lens 23.0 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py, cam_carbine.json)","method":"the dark seam line at column 745, row 244, carried back onto the upper side face's plane","via":"harvest"}}]},"lower_top_below_top":{"label":"The lower side face's top edge below the rail's top","kind":"length","measurements":[{"id":"photo","value":1.07,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-carbine b73705e19a54 (the maker's gallery picture MI-17M-BLK-2: the carbine length alone, from behind its right side and above, muzzle to the right, with a short M-LOK rail section beside it, 1200 x 566)","scaleRef":"a pinhole camera fitted to the rail's 15 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's three M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.33 px, max 4.8 px, f 3984 px, the lens 23.0 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py, cam_carbine.json)","method":"column 745, row 262, carried back onto the lower side face's plane","via":"harvest"}}]},"lower_bottom_below_top":{"label":"The lower side face's bottom edge (where the lower bevel begins) below the rail's top","kind":"length","measurements":[{"id":"photo","value":1.473,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-carbine b73705e19a54 (the maker's gallery picture MI-17M-BLK-2: the carbine length alone, from behind its right side and above, muzzle to the right, with a short M-LOK rail section beside it, 1200 x 566)","scaleRef":"a pinhole camera fitted to the rail's 15 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's three M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.33 px, max 4.8 px, f 3984 px, the lens 23.0 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py, cam_carbine.json)","method":"column 745, row 327, carried back onto the lower side face's plane","via":"harvest"}}]},"bottom_half_width":{"label":"Half the bottom flat's width","kind":"length","measurements":[{"id":"photo","value":0.46,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-carbine b73705e19a54 (the maker's gallery picture MI-17M-BLK-2: the carbine length alone, from behind its right side and above, muzzle to the right, with a short M-LOK rail section beside it, 1200 x 566)","scaleRef":"a pinhole camera fitted to the rail's 15 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's three M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.33 px, max 4.8 px, f 3984 px, the lens 23.0 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py, cam_carbine.json)","method":"the bottom's silhouette (column 745, row 427) carried back: z 0.506 where it meets the maker's height (y = -2.25), 2.283 below the top on z = 0.415","via":"harvest"}}]},"seam_groove":{"label":"The seam's groove (each side), its width and depth","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the seam shows as a dark line a few pixels wide.","via":"harvest"}}]},"wall":{"label":"Its wall's thickness","kind":"length","measurements":[{"id":"assumed","value":0.08,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view looks into an end square on. Set so that the model's aluminium is near the maker's installed weight at the density on file (std.density.aluminium), as the mid-length's is.","via":"harvest"}}]},"front_round":{"label":"The upper half's front top corner, rounded (its radius)","kind":"length","measurements":[{"id":"assumed","value":0.25,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the photo shows the upper half's front rounding over from its side into the rail's front, seen from behind.","via":"harvest"}}]},"collar_od":{"label":"The rear flanges' outside diameter","kind":"length","measurements":[{"id":"assumed","value":1.74,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: inside the delta ring's skirt (std.ar15.slip_ring_skirt_d, 1.750), where they go.","via":"harvest"}}]},"collar_id":{"label":"The rear flanges' inside diameter","kind":"length","measurements":[{"id":"assumed","value":1.6,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: clear of the barrel nut's toothed flange (std.ar15.barrel_nut_flange_od, 1.56) that the skirt surrounds.","via":"harvest"}}]},"hole_pitch":{"label":"The pitch of the round holes along the upper side faces and along the lower bevels","kind":"length","measurements":[{"id":"photo","value":0.732,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-carbine b73705e19a54 (the maker's gallery picture MI-17M-BLK-2: the carbine length alone, from behind its right side and above, muzzle to the right, with a short M-LOK rail section beside it, 1200 x 566)","scaleRef":"a pinhole camera fitted to the rail's 15 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's three M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.33 px, max 4.8 px, f 3984 px, the lens 23.0 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py, cam_carbine.json)","method":"the lower bevel's holes run along their row through the camera (along.py at z 0.78, 1.75 below the top): centres 1.100, 1.835, 2.565, 3.295, 4.018, 4.733, 0.727 apart; the upper side's seven, 0.305 to 4.73, 0.7375 apart; their mean","via":"harvest"}}]},"upper_holes":{"label":"The round holes along each upper side face (regular ones; the large one at the front apart)","kind":"count","measurements":[{"id":"photo","value":7,"unit":"count","source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-carbine b73705e19a54 (the maker's gallery picture MI-17M-BLK-2: the carbine length alone, from behind its right side and above, muzzle to the right, with a short M-LOK rail section beside it, 1200 x 566)","scaleRef":"none: a count","method":"counted on the right side, and the camera's circles at the readings laid back over the photo (circles.py): seven of one size, the eighth place the large one","via":"harvest"}}]},"upper_hole0_from_slot0":{"label":"The upper side face's first round hole (its centre) ahead of the rail's slot 0","kind":"length","measurements":[{"id":"photo","value":0.311,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-carbine b73705e19a54 (the maker's gallery picture MI-17M-BLK-2: the carbine length alone, from behind its right side and above, muzzle to the right, with a short M-LOK rail section beside it, 1200 x 566)","scaleRef":"a pinhole camera fitted to the rail's 15 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's three M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.33 px, max 4.8 px, f 3984 px, the lens 23.0 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py, cam_carbine.json)","method":"the seven holes' runs along their row (0.70 below the top) on the upper face's plane: centres 0.305, 1.06, 1.78, 2.54, 3.25, 4.00, 4.73; less the upper row's pitch times each one's place, 0.30 to 0.33, mean 0.311","via":"harvest"}}]},"upper_hole_d":{"label":"The upper side face's round holes, their diameter","kind":"length","measurements":[{"id":"photo","value":0.59,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-carbine b73705e19a54 (the maker's gallery picture MI-17M-BLK-2: the carbine length alone, from behind its right side and above, muzzle to the right, with a short M-LOK rail section beside it, 1200 x 566)","scaleRef":"a pinhole camera fitted to the rail's 15 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's three M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.33 px, max 4.8 px, f 3984 px, the lens 23.0 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py, cam_carbine.json)","method":"each run's length along the row: 0.56 to 0.62","via":"harvest"}}]},"upper_hole_below_top":{"label":"The upper side face's round holes' centres below the rail's top","kind":"length","measurements":[{"id":"photo","value":0.7,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-carbine b73705e19a54 (the maker's gallery picture MI-17M-BLK-2: the carbine length alone, from behind its right side and above, muzzle to the right, with a short M-LOK rail section beside it, 1200 x 566)","scaleRef":"a pinhole camera fitted to the rail's 15 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's three M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.33 px, max 4.8 px, f 3984 px, the lens 23.0 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py, cam_carbine.json)","method":"the runs along the row at 0.70 below the top (along.py) are each as long as the holes are across (0.56 to 0.62 for 0.59), as a row through their centres is. A chord up and down one hole at column 760 (0.351 to 0.829) took the shelf's outer edge for the hole's top rim (neck_foot_below_top)","via":"harvest"}}]},"big_hole_from_slot0":{"label":"The large hole at the front of each upper side face, its centre ahead of the rail's slot 0","kind":"length","measurements":[{"id":"photo","value":5.5,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-carbine b73705e19a54 (the maker's gallery picture MI-17M-BLK-2: the carbine length alone, from behind its right side and above, muzzle to the right, with a short M-LOK rail section beside it, 1200 x 566)","scaleRef":"a pinhole camera fitted to the rail's 15 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's three M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.33 px, max 4.8 px, f 3984 px, the lens 23.0 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py, cam_carbine.json)","method":"its rims carried back onto the upper face's plane: 5.105 and 5.890 fore and aft","via":"harvest"}}]},"big_hole_length":{"label":"The large front hole's length along the handguard","kind":"length","measurements":[{"id":"photo","value":0.785,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-carbine b73705e19a54 (the maker's gallery picture MI-17M-BLK-2: the carbine length alone, from behind its right side and above, muzzle to the right, with a short M-LOK rail section beside it, 1200 x 566)","scaleRef":"a pinhole camera fitted to the rail's 15 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's three M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.33 px, max 4.8 px, f 3984 px, the lens 23.0 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py, cam_carbine.json)","method":"its rims 5.105 and 5.890 from slot 0","via":"harvest"}}]},"big_hole_height":{"label":"The large front hole's height","kind":"length","measurements":[{"id":"photo","value":0.58,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-carbine b73705e19a54 (the maker's gallery picture MI-17M-BLK-2: the carbine length alone, from behind its right side and above, muzzle to the right, with a short M-LOK rail section beside it, 1200 x 566)","scaleRef":"a pinhole camera fitted to the rail's 15 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's three M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.33 px, max 4.8 px, f 3984 px, the lens 23.0 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py, cam_carbine.json)","method":"its rims 0.374 and 0.955 below the top","via":"harvest"}}]},"big_hole_below_top":{"label":"The large front hole's centre below the rail's top","kind":"length","measurements":[{"id":"photo","value":0.665,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-carbine b73705e19a54 (the maker's gallery picture MI-17M-BLK-2: the carbine length alone, from behind its right side and above, muzzle to the right, with a short M-LOK rail section beside it, 1200 x 566)","scaleRef":"a pinhole camera fitted to the rail's 15 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's three M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.33 px, max 4.8 px, f 3984 px, the lens 23.0 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py, cam_carbine.json)","method":"the middle of its rims, 0.374 and 0.955 below the top","via":"harvest"}}]},"bevel_holes":{"label":"The round holes along each lower bevel","kind":"count","measurements":[{"id":"photo","value":8,"unit":"count","source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-carbine b73705e19a54 (the maker's gallery picture MI-17M-BLK-2: the carbine length alone, from behind its right side and above, muzzle to the right, with a short M-LOK rail section beside it, 1200 x 566)","scaleRef":"none: a count","method":"eight runs along the right lower bevel through the camera (along.py at z 0.78, 1.75 below the top): the first partly behind the rear QD socket's boss, the last run into the light past it","via":"harvest"}}]},"bevel_hole0_from_slot0":{"label":"The lower bevel's first round hole (its centre) ahead of the rail's slot 0","kind":"length","measurements":[{"id":"photo","value":0.373,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-carbine b73705e19a54 (the maker's gallery picture MI-17M-BLK-2: the carbine length alone, from behind its right side and above, muzzle to the right, with a short M-LOK rail section beside it, 1200 x 566)","scaleRef":"a pinhole camera fitted to the rail's 15 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's three M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.33 px, max 4.8 px, f 3984 px, the lens 23.0 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py, cam_carbine.json)","method":"the six whole holes' centres less the bevel row's pitch (0.727) times each one's place: 0.37 to 0.39, mean 0.377; the first's own run ends at 0.66 = 0.36 + 0.30","via":"harvest"}}]},"bevel_hole_d":{"label":"The lower bevel's round holes, their diameter","kind":"length","measurements":[{"id":"photo","value":0.6,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-carbine b73705e19a54 (the maker's gallery picture MI-17M-BLK-2: the carbine length alone, from behind its right side and above, muzzle to the right, with a short M-LOK rail section beside it, 1200 x 566)","scaleRef":"a pinhole camera fitted to the rail's 15 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's three M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.33 px, max 4.8 px, f 3984 px, the lens 23.0 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py, cam_carbine.json)","method":"each whole run along the bevel: 0.595 to 0.605","via":"harvest"}}]},"mlok_slots":{"label":"M-LOK slots in each lower side face","kind":"count","measurements":[{"id":"photo","value":3,"unit":"count","source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-carbine b73705e19a54 (the maker's gallery picture MI-17M-BLK-2: the carbine length alone, from behind its right side and above, muzzle to the right, with a short M-LOK rail section beside it, 1200 x 566)","scaleRef":"none: a count","method":"counted on the right side: three, on the 40 mm pitch (the camera's fit)","via":"harvest"}}]},"mlok_slot0_from_slot0":{"label":"The lower side face's first M-LOK slot (its centre) ahead of the rail's slot 0","kind":"length","measurements":[{"id":"photo","value":1.4,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-carbine b73705e19a54 (the maker's gallery picture MI-17M-BLK-2: the carbine length alone, from behind its right side and above, muzzle to the right, with a short M-LOK rail section beside it, 1200 x 566)","scaleRef":"a pinhole camera fitted to the rail's 15 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's three M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.33 px, max 4.8 px, f 3984 px, the lens 23.0 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py, cam_carbine.json)","method":"the camera's own fit of the row: 1.402; its runs along the row's middle (along.py): the first from 0.745 to 2.045, centre 1.395","via":"harvest"}}]},"mlok_slot0_x":{"label":"The lower side face's first M-LOK slot (its centre) ahead of the receiver's front face","kind":"length","measurements":[{"id":"derived","value":2.436,"unit":"in","pm":0.08,"source":{"type":"derived","expr":"{.rail_slot0_x} + {.mlok_slot0_from_slot0}","via":"harvest"}}]},"mlok_below_top":{"label":"The M-LOK slots' centre line (and the QD sockets') below the rail's top","kind":"length","measurements":[{"id":"photo","value":1.31,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-carbine b73705e19a54 (the maker's gallery picture MI-17M-BLK-2: the carbine length alone, from behind its right side and above, muzzle to the right, with a short M-LOK rail section beside it, 1200 x 566)","scaleRef":"a pinhole camera fitted to the rail's 15 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's three M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.33 px, max 4.8 px, f 3984 px, the lens 23.0 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py, cam_carbine.json)","method":"the camera's fit of the row: 1.310; the QD sockets' rims read their centres 1.256 and 1.294 below","via":"harvest"}}]},"mlok_face_distance":{"label":"The M-LOK faces' distance from the bore axis","kind":"length","measurements":[{"id":"derived","value":0.915,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{.width} / 2","via":"harvest"}}]},"reach_inside":{"label":"The room inside its M-LOK faces before the barrel (what an accessory's nuts may take)","kind":"length","measurements":[],"note":"Not published. It depends on the barrel under it, another part: left missing, and the check reads as unmade."},"qd_rear_from_slot0":{"label":"The rear QD socket's centre ahead of the rail's slot 0 (on each lower side face)","kind":"length","measurements":[{"id":"photo","value":0.266,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-carbine b73705e19a54 (the maker's gallery picture MI-17M-BLK-2: the carbine length alone, from behind its right side and above, muzzle to the right, with a short M-LOK rail section beside it, 1200 x 566)","scaleRef":"a pinhole camera fitted to the rail's 15 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's three M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.33 px, max 4.8 px, f 3984 px, the lens 23.0 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py, cam_carbine.json)","method":"its rim carried back onto the lower face's plane: 0.124 and 0.408 fore and aft, 1.108 and 1.403 below the top","via":"harvest"}}]},"qd_front_from_slot0":{"label":"The front QD socket's centre ahead of the rail's slot 0 (on each lower side face)","kind":"length","measurements":[{"id":"photo","value":5.6,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-carbine b73705e19a54 (the maker's gallery picture MI-17M-BLK-2: the carbine length alone, from behind its right side and above, muzzle to the right, with a short M-LOK rail section beside it, 1200 x 566)","scaleRef":"a pinhole camera fitted to the rail's 15 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's three M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.33 px, max 4.8 px, f 3984 px, the lens 23.0 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py, cam_carbine.json)","method":"its rim carried back onto the lower face's plane: 5.391 and 5.810 fore and aft, 1.109 and 1.479 below the top","via":"harvest"}}]},"qd_d":{"label":"The QD sockets' hole, its diameter","kind":"length","measurements":[{"id":"photo","value":0.34,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-carbine b73705e19a54 (the maker's gallery picture MI-17M-BLK-2: the carbine length alone, from behind its right side and above, muzzle to the right, with a short M-LOK rail section beside it, 1200 x 566)","scaleRef":"a pinhole camera fitted to the rail's 15 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's three M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.33 px, max 4.8 px, f 3984 px, the lens 23.0 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py, cam_carbine.json)","method":"the two sockets' rims: 0.284 and 0.295 (rear, its rim half hidden by the lens's angle), 0.419 and 0.370 (front); their mean","via":"harvest"}}]}}},{"subject":"midwest-industries-drop-in-mlok-mid","title":"Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Mid-Length, MI-18M)","dimensions":{"weight":{"label":"Weight (installed: both halves)","kind":"mass","measurements":[{"id":"maker","value":6.6,"unit":"oz","pm":0.05,"stated":"Installed Weight [...] Mid-Length - 6.6oz","source":{"type":"spec","publisher":"manufacturer","name":"Midwest Industries, AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (SKU AR15M16TWOPI; Length: Mid-Length, MI-18M), Product Details","url":"https://www.midwestindustriesinc.com/product-p/mi-18m-blk.htm","retrieved":"2026-10-28","via":"harvest"}}],"note":"The maker's table is headed \"Installed Weight\": the two halves as they go on the rifle. What is in the box besides (a short M-LOK rail section is pictured with the carbine length) isn't weighed in it as far as the page says."},"length":{"label":"Length (the maker's overall length; read here as the rail's whole length, its tongue's rear end to its front)","kind":"length","measurements":[{"id":"maker","value":8.5,"unit":"in","pm":0.05,"stated":"Overall Length [...] MI-18M - 8.5\"","source":{"type":"spec","publisher":"manufacturer","name":"Midwest Industries, AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (SKU AR15M16TWOPI; Length: Mid-Length, MI-18M), Product Details","url":"https://www.midwestindustriesinc.com/product-p/mi-18m-blk.htm","retrieved":"2026-10-28","via":"harvest"}},{"id":"photo","value":9.04,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-mid 2c00c51da81c (the maker's gallery picture MI-18M-BLK-2: the mid-length alone, from behind its right side and above, muzzle to the right, 1200 x 457)","scaleRef":"a pinhole camera fitted to the rail's 19 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's four M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.0 px, max 3.6 px, f 2754 px, the lens 19.5 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py)","method":"the tongue's rear end (0.996 behind slot 0: tongue_rear_from_slot0) to the rail's and the upper half's front (8.044 ahead: front_from_slot0)","via":"harvest"}}],"adopt":{"from":"photo","reason":"Read against the room it is held in, the fit bears out both, as two spans: the maker's 8.5 is its mounting length (the room between the delta ring's lip and the triangle cap's pocket is 8.44 on the catalog's mid-length barrel: mounting_length), and the photo's 9.04 is the rail's whole length from its tongue, which reaches back over the delta ring to the receiver's face. Its carbine length's page figure, 7 in, is the other span (its rail's whole length, 7.09 by its own photo; its room is 6.50), so the page doesn't give one span for both; this one is the rail's."}},"mounting_length":{"label":"Its mounting length: from its rear flanges' end (on the delta ring's lip) to the end of what goes into the cap (at the inside of the cap's face)","kind":"length","measurements":[{"id":"room","value":8.441,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the room the catalog's mid-length rifle holds it in: from the delta ring's lip (std.ar15.slip_ring_front_x, 0.336 ahead of the receiver's face) to the triangle cap's pocket, the inside of its face (bcm-handguard-cap-triangle-750, its collar and sheet behind its seat), with the cap on BCM's F base on bcm-16-mid-barrel (the base's rear face 8.865 ahead of the receiver's face): 8.441. To a round cap's pocket it would be 8.492.","via":"harvest"}},{"id":"maker","value":8.5,"unit":"in","pm":0.05,"stated":"Overall Length [...] MI-18M - 8.5\"","source":{"type":"spec","publisher":"manufacturer","name":"Midwest Industries, AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (SKU AR15M16TWOPI; Length: Mid-Length, MI-18M), Product Details","url":"https://www.midwestindustriesinc.com/product-p/mi-18m-blk.htm","retrieved":"2026-10-28","via":"harvest"},"note":"The page's \"Overall Length\", read as this span: the one a rifle holds it in agrees within 0.06, and the rail's whole length (length) is 9.04."}],"adopt":{"from":"room","reason":"A part held between two faces is as long as the room it is held in (CLAUDE.md, the P90 magazine): the cap seats it there (D97, ar15.handguard_front). The maker's 8.5 is the same span within its half digit and what the delta ring's spring takes up (0.06)."},"note":"Not seen in the photo: what of its front goes into the cap is inside its front end. It is where the cap seats it (cap_seat), and where the front sight base's rear then stands in its frame (base_rear_x)."},"base_rear_x":{"label":"The front sight base's rear face (the cap's seat), in its frame, with the cap seating it: its mounting length and the cap's face ahead of its rear end","kind":"length","measurements":[{"id":"derived","value":8.86,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.rear_x} + {.mounting_length} + {bcm-handguard-cap-triangle-750.collar} + {bcm-handguard-cap-triangle-750.sheet}","via":"harvest"}}],"note":"What of its hidden front stands in the base's space ahead of this face is cut from its inside (pipeline/blender/midwest_industries_drop_in_mlok_mid.py): the base is sourced, its inside isn't."},"overall_length":{"label":"Its whole length, from its rear flanges' end (in the delta ring) to the lower half's front edge","kind":"length","measurements":[{"id":"photo","value":8.69,"unit":"in","pm":0.07,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-mid 2c00c51da81c (the maker's gallery picture MI-18M-BLK-2: the mid-length alone, from behind its right side and above, muzzle to the right, 1200 x 457)","scaleRef":"a pinhole camera fitted to the rail's 19 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's four M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.0 px, max 3.6 px, f 2754 px, the lens 19.5 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py)","method":"the rear flanges' rim at 1.0 behind the rail's slot 0 (rail_slot0_from_rear) to the lower half's front edge at 7.69 (lower_front_from_slot0)","via":"harvest"}}],"note":"Longer than the room between the delta ring's lip and the triangle cap's floor on a mid-length barrel (8.45 in the catalog's build: std.ar15.slip_ring_front_x and the cap's own figures): its front end stands over the cap and 0.17 in over the front sight base's rear, as Magpul's MOE's wraps it (its 9.2 in overall against 8.6 mounting)."},"width":{"label":"Width (across the lower half's side faces)","kind":"length","measurements":[{"id":"maker","value":1.83,"unit":"in","pm":0.005,"stated":"1.83\" wide and 2.25\" tall","source":{"type":"spec","publisher":"manufacturer","name":"Midwest Industries, AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (SKU AR15M16TWOPI; Length: Mid-Length, MI-18M), Product Details","url":"https://www.midwestindustriesinc.com/product-p/mi-18m-blk.htm","retrieved":"2026-10-28","via":"harvest"}}],"note":"Taken as across the lower half's flat side faces, the widest in the photo (the camera's plane for the M-LOK slots)."},"height":{"label":"Height (the rail's top to the bottom)","kind":"length","measurements":[{"id":"maker","value":2.25,"unit":"in","pm":0.005,"stated":"1.83\" wide and 2.25\" tall","source":{"type":"spec","publisher":"manufacturer","name":"Midwest Industries, AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (SKU AR15M16TWOPI; Length: Mid-Length, MI-18M), Product Details","url":"https://www.midwestindustriesinc.com/product-p/mi-18m-blk.htm","retrieved":"2026-10-28","via":"harvest"}},{"id":"photo","value":2.27,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-mid 2c00c51da81c (the maker's gallery picture MI-18M-BLK-2: the mid-length alone, from behind its right side and above, muzzle to the right, 1200 x 457)","scaleRef":"a pinhole camera fitted to the rail's 19 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's four M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.0 px, max 3.6 px, f 2754 px, the lens 19.5 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py)","method":"the bottom's silhouette at column 735 (row 352) carried back onto the lower bevel's plane and onto z = 0.415: 2.285 and 2.274 below the rail's top","via":"harvest"}}],"adopt":{"from":"maker","reason":"The maker's figure; the camera, which wasn't fitted to any height but the M-LOK slots' 7 mm, reads 0.02 more."}},"inside_diameter":{"label":"Inside diameter","kind":"length","measurements":[],"note":"Not published, and no view on file looks into either end square on. Left missing: the model's inside is its wall (assumed) inside its section."},"rear_x":{"label":"Its rear end (the rear flanges' end, bearing on the delta ring's lip) ahead of the receiver's front face","kind":"length","measurements":[{"id":"derived","value":0.336,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{std.ar15.slip_ring_front_x}","via":"harvest"}}],"note":"Where the standard's delta ring holds it: its rear flanges in the ring's skirt, against the lip (std.ar15.slip_ring_front_x, from the Army's drawings). Its instructions: \"Pull the delta ring to the rear and remove both sections of the plastic handguards, pulling out from the delta ring end first.\""},"rail_top_above_bore":{"label":"Its rail's top above the bore axis","kind":"length","measurements":[{"id":"level","value":1.2125,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{bcm-m4-upper.rail_top_above_pin} - {bcm-m4-upper.bore_axis_above_pin}","via":"harvest"}}],"note":"Level with a mil-spec receiver's rail: the maker's \"Monolithic type continuous top rail\". So the catalog's BCM M4 upper's rail top above its pin line less its bore's height above it; the camera reads the bottom 2.27 below the rail's top, which with this puts the bore 1.06 above the bottom (1.0375 by the maker's height)."},"rail_slots":{"label":"Slots in its top rail","kind":"count","measurements":[{"id":"photo","value":20,"unit":"count","source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-mid 2c00c51da81c (the maker's gallery picture MI-18M-BLK-2: the mid-length alone, from behind its right side and above, muzzle to the right, 1200 x 457)","scaleRef":"none: a count","method":"the top silhouette's dips under the lands' envelope (dips.py): 19, centres from px 203.9 to 1037.8, each 40.5 to 52.9 px from the next, falling smoothly with the distance (a projective map through them leaves 0.38 px rms), none missing; and a twentieth behind them, between the tongue's front (px 130) and the first land (px 163), 0.42 behind the first by that map (one pitch is 0.394) and 0.6 of a pitch across as a slot is (0.52): the tongue is a long land. The carbine's photo has that slot among its own run of fifteen, at its pitch","via":"harvest"}}]},"rail_slot0_from_rear":{"label":"Its rail's rearmost slot (its centre) ahead of its rear end (the rear flanges' end)","kind":"length","measurements":[{"id":"photo","value":0.606,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-mid 2c00c51da81c (the maker's gallery picture MI-18M-BLK-2: the mid-length alone, from behind its right side and above, muzzle to the right, 1200 x 457)","scaleRef":"a pinhole camera fitted to the rail's 19 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's four M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.0 px, max 3.6 px, f 2754 px, the lens 19.5 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py)","method":"the flanges' rear rim: circles of their radius (collar_od) about the bore axis carried through the camera at 0.85 to 1.45 behind slot 0 over the photo (rim.py, rim_mid.png): the lower flange's outer edge follows the one at 1.04, the upper's the one at 0.95. (A first reading, 1.45, took the lower flange's leftmost point for its near side at 3 o'clock; it is on the far side.)","via":"harvest"}}]},"rail_slot0_x":{"label":"Its rail's rearmost slot (its centre) ahead of the receiver's front face","kind":"length","measurements":[{"id":"derived","value":0.942,"unit":"in","pm":0.075,"source":{"type":"derived","expr":"{.rear_x} + {.rail_slot0_from_rear}","via":"harvest"}}]},"tongue_rear_from_slot0":{"label":"The rail's tongue (its plain rear part over the delta ring), its rear end behind the rail's slot 0","kind":"length","measurements":[{"id":"photo","value":0.996,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-mid 2c00c51da81c (the maker's gallery picture MI-18M-BLK-2: the mid-length alone, from behind its right side and above, muzzle to the right, 1200 x 457)","scaleRef":"a pinhole camera fitted to the rail's 19 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's four M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.0 px, max 3.6 px, f 2754 px, the lens 19.5 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py)","method":"the tongue's far rear corner (column 10, row 112) on the top flat's far edge: 1.387 behind slot 0 through the camera, 1.40 by the projective map of the lands alone (fit1d.py)","via":"harvest"}}],"note":"With its rear flanges in the delta ring (rear_x, rail_slot0_from_rear) this puts the tongue's rear end 0.05 in behind the upper receiver's front face, inside the two readings' ± (0.04 and 0.06): it reaches the receiver, the maker's \"continuous top rail\". Drawn bearing on the receiver's front face."},"tongue_thickness":{"label":"The rail's tongue's thickness (a plate under the rail's top)","kind":"length","measurements":[{"id":"assumed","value":0.12,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the photo shows the plate's far rear edge 10 to 13 px tall from 19 in, edge-on from above where it isn't a height that can be read. Its underside stands 0.13 over the delta ring's front land (std.ar15.slip_ring_front_od) under a rail level with the receiver's.","via":"harvest"}}]},"front_from_slot0":{"label":"The upper half's front (the rail's front end) ahead of the rail's slot 0","kind":"length","measurements":[{"id":"photo","value":8.044,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-mid 2c00c51da81c (the maker's gallery picture MI-18M-BLK-2: the mid-length alone, from behind its right side and above, muzzle to the right, 1200 x 457)","scaleRef":"a pinhole camera fitted to the rail's 19 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's four M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.0 px, max 3.6 px, f 2754 px, the lens 19.5 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py)","method":"the upper side face's front edge carried back onto its plane: 7.58 at the holes' height, 7.63 and 7.68 lower; the last land's front, by the lands' projective map, 7.646","via":"harvest"}}]},"upper_rear_from_slot0":{"label":"The upper half's body's rear face behind the rail's slot 0","kind":"length","measurements":[{"id":"photo","value":0.406,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-mid 2c00c51da81c (the maker's gallery picture MI-18M-BLK-2: the mid-length alone, from behind its right side and above, muzzle to the right, 1200 x 457)","scaleRef":"a pinhole camera fitted to the rail's 19 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's four M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.0 px, max 3.6 px, f 2754 px, the lens 19.5 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py)","method":"the upper side face's rear edge carried back onto its plane (z 0.85): 0.78 at two heights, 0.83 along the holes' row","via":"harvest"}}]},"lower_rear_from_slot0":{"label":"The lower half's body's rear face behind the rail's slot 0","kind":"length","measurements":[{"id":"photo","value":0.156,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-mid 2c00c51da81c (the maker's gallery picture MI-18M-BLK-2: the mid-length alone, from behind its right side and above, muzzle to the right, 1200 x 457)","scaleRef":"a pinhole camera fitted to the rail's 19 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's four M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.0 px, max 3.6 px, f 2754 px, the lens 19.5 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py)","method":"the lower side face's rear edge carried back onto its plane at three heights: 0.516, 0.546, 0.567 behind slot 0","via":"harvest"}}]},"lower_front_from_slot0":{"label":"The lower half's front edge ahead of the rail's slot 0","kind":"length","measurements":[{"id":"photo","value":8.084,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-mid 2c00c51da81c (the maker's gallery picture MI-18M-BLK-2: the mid-length alone, from behind its right side and above, muzzle to the right, 1200 x 457)","scaleRef":"a pinhole camera fitted to the rail's 19 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's four M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.0 px, max 3.6 px, f 2754 px, the lens 19.5 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py)","method":"the lower side face's front edge carried back onto its plane: 7.75, 7.69, 7.69 from its top to its bottom","via":"harvest"}}]},"bottom_cut_from_slot0":{"label":"Where the bottom flat ends at the front (its front part cut up), ahead of the rail's slot 0","kind":"length","measurements":[{"id":"photo","value":7.714,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-mid 2c00c51da81c (the maker's gallery picture MI-18M-BLK-2: the mid-length alone, from behind its right side and above, muzzle to the right, 1200 x 457)","scaleRef":"a pinhole camera fitted to the rail's 19 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's four M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.0 px, max 3.6 px, f 2754 px, the lens 19.5 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py)","method":"the bottom's step at column 1110 row 292 carried back onto the bottom's plane (y = -2.25) and onto z 0.4: 7.316 and 7.328","via":"harvest"}}]},"bottom_cut_height":{"label":"How far the bottom's front part is cut up","kind":"length","measurements":[{"id":"assumed","value":0.12,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the step shows 12 to 15 px tall in the photo, edge-on from above, where it isn't a height that can be read.","via":"harvest"}}]},"neck_foot_below_top":{"label":"The rail's neck's foot (where the upper half's top, a shelf out to its side faces, meets the neck under the head) below the rail's top","kind":"length","measurements":[{"id":"neck","value":0.43,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-mid 2c00c51da81c (the maker's gallery picture MI-18M-BLK-2: the mid-length alone, from behind its right side and above, muzzle to the right, 1200 x 457)","scaleRef":"a pinhole camera fitted to the rail's 19 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's four M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.0 px, max 3.6 px, f 2754 px, the lens 19.5 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py)","method":"the dark line under the engraved face (column 735, rows 111 to 113) carried back onto the neck's plane (z 0.343, the head's lower faces carried on to shoulder_top_below_top): 0.425 to 0.440","via":"harvest"}},{"id":"side","value":0.344,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-mid 2c00c51da81c (the maker's gallery picture MI-18M-BLK-2: the mid-length alone, from behind its right side and above, muzzle to the right, 1200 x 457)","scaleRef":"a pinhole camera fitted to the rail's 19 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's four M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.0 px, max 3.6 px, f 2754 px, the lens 19.5 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py)","method":"the same line carried back onto the upper side face's plane (z 0.85) instead","via":"harvest"}}],"adopt":{"from":"neck","reason":"One line of the photo, read on two planes; which one it lies in the photo can't say. Read on the side face's plane (the first reading, a sloped shoulder from the neck out to the side faces under it), the body stood 0.18 to 0.19 in under the rail's top beside the head, and 17 of the 30 clamps on file stood in it (Aimpoint's T-2 LRP 0.06 cubic inches, its PRO and Duty RDS, EOTECH's STS, SIG's Romeo5, Holosun's ARO and HS510C, Magpul's MBUS 3: rail-clamps.test.ts); on the maker's \\\"MIL-STD 1913 top rail\\\" they go. Read on the neck's plane, the engraved face is the neck's side, as the maker engraves its name under the rail on its Combat Rail's neck (0.69 in wide down to 0.56 under its top: midwest-combat-rail-15-handguard), and a forged upper's neck runs as deep (0.39); at column 747 the shelf's outer edge projects 10 px under that line, where the photo's grey runs on unbroken to the holes' tops 0.45 down (no edge to read). Drawn so: a neck down to here, the shelf out to the side faces."}},"shoulder_top_below_top":{"label":"The neck's top: where the head's lower faces, carried on at 45 degrees, meet the neck's sides, below the rail's top","kind":"length","measurements":[{"id":"photo","value":0.204,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-mid 2c00c51da81c (the maker's gallery picture MI-18M-BLK-2: the mid-length alone, from behind its right side and above, muzzle to the right, 1200 x 457)","scaleRef":"a pinhole camera fitted to the rail's 19 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's four M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.0 px, max 3.6 px, f 2754 px, the lens 19.5 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py)","method":"the top of the dark band under the lands (column 735, row 82: the head's lower faces and the neck's top in their shadow) carried back onto the neck's plane (z 0.343): 0.204. (First read as the top of a shoulder sloping out from the head, on a plane at z 0.6; with the engraved face taken for the neck's side, it is this.)","via":"harvest"}}],"note":"With the standard's head (lib.rail_half) this sets the neck's half width: the head's lower faces carried on to here."},"upper_half_width":{"label":"Width across the upper half's side faces","kind":"length","measurements":[{"id":"assumed","value":1.7,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the photo shows the lower half's top as a ledge outside the upper half's side; how far isn't read from a view from above. Every reading on the upper side face is carried back onto this plane.","via":"harvest"}}]},"channel_roof_below_top":{"label":"The gas tube's channel up inside the neck: its roof below the rail's top","kind":"length","measurements":[{"id":"assumed","value":0.15,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view looks into either end. The neck stands over the gas tube (std.ar15.gas_tube_above_bore), so it is hollow up to a web under the rail's slots' floors (std.picatinny.slot_depth, 0.118), as thick as a few hundredths.","via":"harvest"}}]},"seam_below_top":{"label":"The upper side face's lower edge (the seam between the halves) below the rail's top","kind":"length","measurements":[{"id":"photo","value":0.978,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-mid 2c00c51da81c (the maker's gallery picture MI-18M-BLK-2: the mid-length alone, from behind its right side and above, muzzle to the right, 1200 x 457)","scaleRef":"a pinhole camera fitted to the rail's 19 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's four M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.0 px, max 3.6 px, f 2754 px, the lens 19.5 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py)","method":"the dark seam line at column 735, row 199, carried back onto the upper side face's plane","via":"harvest"}}]},"lower_top_below_top":{"label":"The lower side face's top edge below the rail's top","kind":"length","measurements":[{"id":"photo","value":1.067,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-mid 2c00c51da81c (the maker's gallery picture MI-18M-BLK-2: the mid-length alone, from behind its right side and above, muzzle to the right, 1200 x 457)","scaleRef":"a pinhole camera fitted to the rail's 19 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's four M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.0 px, max 3.6 px, f 2754 px, the lens 19.5 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py)","method":"column 735, row 213, carried back onto the lower side face's plane","via":"harvest"}}]},"lower_bottom_below_top":{"label":"The lower side face's bottom edge (where the lower bevel begins) below the rail's top","kind":"length","measurements":[{"id":"photo","value":1.542,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-mid 2c00c51da81c (the maker's gallery picture MI-18M-BLK-2: the mid-length alone, from behind its right side and above, muzzle to the right, 1200 x 457)","scaleRef":"a pinhole camera fitted to the rail's 19 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's four M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.0 px, max 3.6 px, f 2754 px, the lens 19.5 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py)","method":"column 735, row 276, carried back onto the lower side face's plane","via":"harvest"}}]},"bottom_half_width":{"label":"Half the bottom flat's width","kind":"length","measurements":[{"id":"photo","value":0.4,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-mid 2c00c51da81c (the maker's gallery picture MI-18M-BLK-2: the mid-length alone, from behind its right side and above, muzzle to the right, 1200 x 457)","scaleRef":"a pinhole camera fitted to the rail's 19 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's four M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.0 px, max 3.6 px, f 2754 px, the lens 19.5 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py)","method":"the bottom's silhouette (column 735, row 352) carried back onto the lower bevel's plane through the side face's lower edge: z 0.38 at 2.285 below the top; 0.415 where it meets the maker's height","via":"harvest"}}]},"seam_groove":{"label":"The seam's groove (each side), its width and depth","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the seam shows as a dark line a few pixels wide.","via":"harvest"}}]},"wall":{"label":"Its wall's thickness","kind":"length","measurements":[{"id":"assumed","value":0.08,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view looks into an end square on. Set so that the model's aluminium is near the maker's installed weight at the density on file (std.density.aluminium).","via":"harvest"}}]},"front_round":{"label":"The upper half's front top corner, rounded (its radius)","kind":"length","measurements":[{"id":"assumed","value":0.25,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the photo shows the upper half's front rounding over from its side into the rail's front, seen from behind.","via":"harvest"}}]},"collar_od":{"label":"The rear flanges' outside diameter","kind":"length","measurements":[{"id":"assumed","value":1.74,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: inside the delta ring's skirt (std.ar15.slip_ring_skirt_d, 1.750), where they go.","via":"harvest"}}]},"collar_id":{"label":"The rear flanges' inside diameter","kind":"length","measurements":[{"id":"assumed","value":1.6,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: clear of the barrel nut's toothed flange (std.ar15.barrel_nut_flange_od, 1.56) that the skirt surrounds.","via":"harvest"}}]},"hole_pitch":{"label":"The pitch of the round holes along the upper side faces and along the lower bevels","kind":"length","measurements":[{"id":"photo","value":0.731,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-mid 2c00c51da81c (the maker's gallery picture MI-18M-BLK-2: the mid-length alone, from behind its right side and above, muzzle to the right, 1200 x 457)","scaleRef":"a pinhole camera fitted to the rail's 19 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's four M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.0 px, max 3.6 px, f 2754 px, the lens 19.5 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py)","method":"the lower bevel's ten holes run along their row through the camera (along.py at 1.896 below the top): edges every 0.725 to 0.735 in, centres 0.765 to 5.880 over seven pitches; the upper side's nine regular holes agree, 0.725 over eight","via":"harvest"}}]},"upper_holes":{"label":"The round holes along each upper side face (regular ones; the large one at the front apart)","kind":"count","measurements":[{"id":"photo","value":9,"unit":"count","source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-mid 2c00c51da81c (the maker's gallery picture MI-18M-BLK-2: the mid-length alone, from behind its right side and above, muzzle to the right, 1200 x 457)","scaleRef":"none: a count","method":"counted on the right side: nine of one size, and a tenth, larger, at the front","via":"harvest"}}]},"upper_hole0_from_slot0":{"label":"The upper side face's first round hole (its centre) ahead of the rail's slot 0","kind":"length","measurements":[{"id":"photo","value":0.502,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-mid 2c00c51da81c (the maker's gallery picture MI-18M-BLK-2: the mid-length alone, from behind its right side and above, muzzle to the right, 1200 x 457)","scaleRef":"a pinhole camera fitted to the rail's 19 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's four M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.0 px, max 3.6 px, f 2754 px, the lens 19.5 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py)","method":"the nine holes' runs along their row (0.70 below the top) on the upper face's plane: centres 0.135, 0.84, 1.60, 2.30, 3.04, 3.75, 4.49, 5.20, 5.935; less the pitch times each one's place, 0.083 to 0.138, mean 0.108","via":"harvest"}}]},"upper_hole_d":{"label":"The upper side face's round holes, their diameter","kind":"length","measurements":[{"id":"photo","value":0.59,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-mid 2c00c51da81c (the maker's gallery picture MI-18M-BLK-2: the mid-length alone, from behind its right side and above, muzzle to the right, 1200 x 457)","scaleRef":"a pinhole camera fitted to the rail's 19 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's four M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.0 px, max 3.6 px, f 2754 px, the lens 19.5 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py)","method":"each run's length along the row: 0.55 to 0.61, mean 0.59; up and down the one at 3.73, 0.53 (its lower rim at the seam's edge)","via":"harvest"}}]},"upper_hole_below_top":{"label":"The upper side face's round holes' centres below the rail's top","kind":"length","measurements":[{"id":"photo","value":0.7,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-mid 2c00c51da81c (the maker's gallery picture MI-18M-BLK-2: the mid-length alone, from behind its right side and above, muzzle to the right, 1200 x 457)","scaleRef":"a pinhole camera fitted to the rail's 19 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's four M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.0 px, max 3.6 px, f 2754 px, the lens 19.5 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py)","method":"the hole at 3.73: its rims 0.449 and 0.980 below the top; the row's centres read 0.65 at the rear and 0.76 at the front","via":"harvest"}}]},"big_hole_from_slot0":{"label":"The large hole at the front of each upper side face, its centre ahead of the rail's slot 0","kind":"length","measurements":[{"id":"photo","value":7.144,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-mid 2c00c51da81c (the maker's gallery picture MI-18M-BLK-2: the mid-length alone, from behind its right side and above, muzzle to the right, 1200 x 457)","scaleRef":"a pinhole camera fitted to the rail's 19 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's four M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.0 px, max 3.6 px, f 2754 px, the lens 19.5 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py)","method":"its rims carried back onto the upper face's plane: 6.33 and 7.17 fore and aft","via":"harvest"}}]},"big_hole_length":{"label":"The large front hole's length along the handguard","kind":"length","measurements":[{"id":"photo","value":0.84,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-mid 2c00c51da81c (the maker's gallery picture MI-18M-BLK-2: the mid-length alone, from behind its right side and above, muzzle to the right, 1200 x 457)","scaleRef":"a pinhole camera fitted to the rail's 19 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's four M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.0 px, max 3.6 px, f 2754 px, the lens 19.5 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py)","method":"its rims 6.327 and 7.165 from slot 0","via":"harvest"}}]},"big_hole_height":{"label":"The large front hole's height","kind":"length","measurements":[{"id":"photo","value":0.56,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-mid 2c00c51da81c (the maker's gallery picture MI-18M-BLK-2: the mid-length alone, from behind its right side and above, muzzle to the right, 1200 x 457)","scaleRef":"a pinhole camera fitted to the rail's 19 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's four M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.0 px, max 3.6 px, f 2754 px, the lens 19.5 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py)","method":"its rims 0.423 and 0.982 below the top","via":"harvest"}}]},"big_hole_below_top":{"label":"The large front hole's centre below the rail's top","kind":"length","measurements":[{"id":"photo","value":0.7,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-mid 2c00c51da81c (the maker's gallery picture MI-18M-BLK-2: the mid-length alone, from behind its right side and above, muzzle to the right, 1200 x 457)","scaleRef":"a pinhole camera fitted to the rail's 19 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's four M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.0 px, max 3.6 px, f 2754 px, the lens 19.5 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py)","method":"the middle of its rims, 0.423 and 0.982 below the top","via":"harvest"}}]},"bevel_holes":{"label":"The round holes along each lower bevel","kind":"count","measurements":[{"id":"photo","value":10,"unit":"count","source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-mid 2c00c51da81c (the maker's gallery picture MI-18M-BLK-2: the mid-length alone, from behind its right side and above, muzzle to the right, 1200 x 457)","scaleRef":"none: a count","method":"ten runs along the right lower bevel's middle through the camera, the first partly behind the rear QD socket's boss","via":"harvest"}}]},"bevel_hole0_from_slot0":{"label":"The lower bevel's first round hole (its centre) ahead of the rail's slot 0","kind":"length","measurements":[{"id":"photo","value":0.428,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-mid 2c00c51da81c (the maker's gallery picture MI-18M-BLK-2: the mid-length alone, from behind its right side and above, muzzle to the right, 1200 x 457)","scaleRef":"a pinhole camera fitted to the rail's 19 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's four M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.0 px, max 3.6 px, f 2754 px, the lens 19.5 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py)","method":"the second hole's centre (0.765) less a pitch; the first's own run, partly hidden, ends at 0.335 = 0.035 + 0.30","via":"harvest"}}]},"bevel_hole_d":{"label":"The lower bevel's round holes, their diameter","kind":"length","measurements":[{"id":"photo","value":0.6,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-mid 2c00c51da81c (the maker's gallery picture MI-18M-BLK-2: the mid-length alone, from behind its right side and above, muzzle to the right, 1200 x 457)","scaleRef":"a pinhole camera fitted to the rail's 19 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's four M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.0 px, max 3.6 px, f 2754 px, the lens 19.5 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py)","method":"each run along the bevel's middle: 0.590 to 0.605","via":"harvest"}}]},"mlok_slots":{"label":"M-LOK slots in each lower side face","kind":"count","measurements":[{"id":"photo","value":4,"unit":"count","source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-mid 2c00c51da81c (the maker's gallery picture MI-18M-BLK-2: the mid-length alone, from behind its right side and above, muzzle to the right, 1200 x 457)","scaleRef":"none: a count","method":"counted on the right side: four, on the 40 mm pitch (the camera's fit)","via":"harvest"}}]},"mlok_slot0_from_slot0":{"label":"The lower side face's first M-LOK slot (its centre) ahead of the rail's slot 0","kind":"length","measurements":[{"id":"photo","value":1.634,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-mid 2c00c51da81c (the maker's gallery picture MI-18M-BLK-2: the mid-length alone, from behind its right side and above, muzzle to the right, 1200 x 457)","scaleRef":"a pinhole camera fitted to the rail's 19 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's four M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.0 px, max 3.6 px, f 2754 px, the lens 19.5 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py)","method":"the camera's own fit of the row: 1.227; its runs along the row's middle (along.py): 1.25, then 2.81, 4.385, 5.98","via":"harvest"}}]},"mlok_slot0_x":{"label":"The lower side face's first M-LOK slot (its centre) ahead of the receiver's front face","kind":"length","measurements":[{"id":"derived","value":2.576,"unit":"in","pm":0.08,"source":{"type":"derived","expr":"{.rail_slot0_x} + {.mlok_slot0_from_slot0}","via":"harvest"}}]},"mlok_below_top":{"label":"The M-LOK slots' centre line (and the QD sockets') below the rail's top","kind":"length","measurements":[{"id":"photo","value":1.38,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-mid 2c00c51da81c (the maker's gallery picture MI-18M-BLK-2: the mid-length alone, from behind its right side and above, muzzle to the right, 1200 x 457)","scaleRef":"a pinhole camera fitted to the rail's 19 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's four M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.0 px, max 3.6 px, f 2754 px, the lens 19.5 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py)","method":"the camera's fit of the row: 1.380; the QD sockets' rims read their centres 1.374 and 1.389 below","via":"harvest"}}]},"mlok_face_distance":{"label":"The M-LOK faces' distance from the bore axis","kind":"length","measurements":[{"id":"derived","value":0.915,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{.width} / 2","via":"harvest"}}]},"qd_rear_from_slot0":{"label":"The rear QD socket's centre ahead of the rail's slot 0 (on each lower side face)","kind":"length","measurements":[{"id":"photo","value":0.394,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-mid 2c00c51da81c (the maker's gallery picture MI-18M-BLK-2: the mid-length alone, from behind its right side and above, muzzle to the right, 1200 x 457)","scaleRef":"a pinhole camera fitted to the rail's 19 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's four M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.0 px, max 3.6 px, f 2754 px, the lens 19.5 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py)","method":"its rim carried back onto the lower face's plane: -0.178 and 0.172 fore and aft, centre -0.004","via":"harvest"}}]},"qd_front_from_slot0":{"label":"The front QD socket's centre ahead of the rail's slot 0 (on each lower side face)","kind":"length","measurements":[{"id":"photo","value":7.604,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-mid 2c00c51da81c (the maker's gallery picture MI-18M-BLK-2: the mid-length alone, from behind its right side and above, muzzle to the right, 1200 x 457)","scaleRef":"a pinhole camera fitted to the rail's 19 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's four M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.0 px, max 3.6 px, f 2754 px, the lens 19.5 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py)","method":"its rim carried back onto the lower face's plane: 7.027 and 7.403 fore and aft, 1.203 and 1.584 below the top","via":"harvest"}}]},"qd_d":{"label":"The QD sockets' hole, its diameter","kind":"length","measurements":[{"id":"photo","value":0.375,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/midwest-industries-drop-in-mlok-mid 2c00c51da81c (the maker's gallery picture MI-18M-BLK-2: the mid-length alone, from behind its right side and above, muzzle to the right, 1200 x 457)","scaleRef":"a pinhole camera fitted to the rail's 19 slots (std.picatinny.slot_pitch, on the far edge of the top flat) and the right side's four M-LOK slots (std.mlok.slot_length, slot_width, slot_pitch, the face at half the maker's width): rms 1.0 px, max 3.6 px, f 2754 px, the lens 19.5 in away (.cache/batch15/midwest-industries-drop-in-mlok-mid/cam.py)","method":"the two sockets' rims: 0.350 and 0.383 (rear), 0.376 and 0.381 (front), fore and aft and up and down","via":"harvest"}}]},"reach_inside":{"label":"The room inside its M-LOK faces before the barrel (what an accessory's nuts may take)","kind":"length","measurements":[],"note":"Not published. It depends on the barrel under it, another part: left missing, and the check reads as unmade."}}},{"subject":"midwest-mk2-qd-t2-226","title":"Midwest Industries MK2 QD T2 Aimpoint Mount, NV 2.26 in height (MI-MK2-QDT2NV-2.26)","dimensions":{"optical_height":{"label":"The dot's axis over the rail's top at this height (the maker's \"NV 2.26” height\": a T-2 taken as the dot)","kind":"length","measurements":[{"id":"maker","value":2.26,"unit":"in","pm":0.005,"stated":"Available in Low, Lower 1/3 Cowitness, Absolute Cowitness, and NV 2.26” height","source":{"type":"spec","publisher":"manufacturer","name":"Midwest Industries, MK2 QD T2 Aimpoint Mount (MK2QDT2AIMPO): its option list and its feature list","url":"https://midwestindustriesinc.com/mk2-qd-t2-aimpoint-mount/","retrieved":"2026-11-03","via":"harvest"}}],"note":"The maker names the option and gives no dot: \"Available in Low, Lower 1/3 Cowitness, Absolute Cowitness, and NV 2.26” height\". Primary Arms: \"This is the NV 2.26-inch height, which raises the optic for a heads-up posture and for use with night vision, well above a standard iron sight cowitness.\" Taken as the axis over the rail of a T-2, the dot the mount is named for (\"MK2 QD T2 Aimpoint Mount\"; Primary Arms' table: \"Compatible Model Aimpoint Micro T-1, Aimpoint Micro T-2\"): an assumption, said so. A lead, not this part's source: Police1 of the maker's older non-QD night vision mount (SHOT Show 2020, the oval-hole mount whose own name at the maker is NV 2.33\"): \"the Midwest Industries night vision tall mount position an Aimpoint T1 style optic at 2.26″ above the top rail\"."},"deck_above_rail":{"label":"The deck's top (where the dot's base sits) above the rail's top","kind":"length","measurements":[{"id":"maker-less-t2","value":1.671,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.optical_height} - {aimpoint-micro-t-2.axis_above_base}","via":"harvest"},"note":"2.26 in less the T-2's 0.589 in over its base, if the maker's figure is a T-2's axis (optical_height)."},{"id":"photo","value":1.63,"unit":"in","pm":0.09,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-226 56a1f4eb07f1 (Midwest Industries' MI-MK2-QDT2-NV, also its picture for the 2.26\" option: this mount from the front right and above, the lever closed, 1280 x 1280) against references/midwest-mk2-qd-t2-lower-13 5fbbfa2e9c84 (its MK2-QDT213-ra: the 1/3 height in the same pose)","scaleRef":"the QD lever, the same part in both pictures: its tail 142 and 143 px high in the two (columns 300 to 390) for its height in the 1/3's right view (profiles.lever there, 0.234 to -0.263 in at the tail: 288 px/in, as the two pictures are drawn to one scale and one pose)","method":"between the deck's lower edge and the lever's top, columns 450 to 510: 346 px here against the 1/3's 194, the deck 79 px higher and the lever 64 px lower in the frame: 152 px more, 0.53 in, over the 1/3's deck height (midwest-mk2-qd-t2-lower-13.deck_above_rail, 1.10). The ± is the 1/3's 0.06 and how a quarter view's vertical scale is taken (the lever's top face seen from above is in its 143 px)","via":"harvest"}}],"adopt":{"from":"maker-less-t2","reason":"The maker's own figure for this height, less the T-2's axis over its base; its picture against the 1/3's in the same pose agrees within 0.04 in, inside both readings."}},"web_length":{"label":"The web between the deck and the base: its length along the rail (straight-sided at this height)","kind":"length","measurements":[{"id":"photo","value":0.95,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-226 56a1f4eb07f1 (Midwest Industries' MI-MK2-QDT2-NV, also its picture for the 2.26\" option: this mount from the front right and above, the lever closed, 1280 x 1280) against references/midwest-mk2-qd-t2-lower-13 5fbbfa2e9c84 (its MK2-QDT213-ra: the 1/3 height in the same pose)","scaleRef":"the 1/3's web at its narrowest (midwest-mk2-qd-t2-lower-13 profiles.side: 0.786 in), seen in the same pose, and the view's scale along the rail from the lever's tail (288 px/in up it; turned about 30 degrees from square, about 257 px/in along it)","method":"the web's silhouette rows 480 to 680: x 551 to 823, 272 px, against the 1/3's narrowest, rows 580 to 600: x 582 to 806, 224 px: 48 px longer","via":"harvest"}}],"note":"At this height the web is a straight-sided slab with an oval panel on its flank, not the 1/3's waisted one (both quarter views)."},"web_oval_length":{"label":"The oval panel on each flank of the web: its length along the rail (its groove's middle)","kind":"length","measurements":[{"id":"photo","value":0.45,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-226 56a1f4eb07f1 (Midwest Industries' MI-MK2-QDT2-NV, also its picture for the 2.26\" option: this mount from the front right and above, the lever closed, 1280 x 1280) against references/midwest-mk2-qd-t2-lower-13 5fbbfa2e9c84 (its MK2-QDT213-ra: the 1/3 height in the same pose)","scaleRef":"the view's scale along the rail as web_length has it (about 257 px/in)","method":"the oval groove round the panel with the maker's mark on the web's right flank: x 590 to 705 at its middle height, 115 px","via":"harvest"}}]},"web_oval_height":{"label":"The oval panel on each flank of the web: its height (its groove's middle)","kind":"length","measurements":[{"id":"photo","value":0.9,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-226 56a1f4eb07f1 (Midwest Industries' MI-MK2-QDT2-NV, also its picture for the 2.26\" option: this mount from the front right and above, the lever closed, 1280 x 1280) against references/midwest-mk2-qd-t2-lower-13 5fbbfa2e9c84 (its MK2-QDT213-ra: the 1/3 height in the same pose)","scaleRef":"the lever's tail as deck_above_rail's photo reading has it (288 px/in up the view)","method":"the groove's top and bottom ends at rows 505 and 765, 260 px","via":"harvest"}}]},"web_oval_groove":{"label":"The oval panel's groove: its width","kind":"length","measurements":[{"id":"photo","value":0.03,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-226 56a1f4eb07f1 (Midwest Industries' MI-MK2-QDT2-NV, also its picture for the 2.26\" option: this mount from the front right and above, the lever closed, 1280 x 1280) against references/midwest-mk2-qd-t2-lower-13 5fbbfa2e9c84 (its MK2-QDT213-ra: the 1/3 height in the same pose)","scaleRef":"as web_oval_height","method":"the dark line round the panel, about 8 px across","via":"harvest"}}]},"web_fillet":{"label":"The rounds where the web meets the deck and the base","kind":"length","measurements":[{"id":"assumed","value":0.08,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the web's front and rear faces run straight from a small round under the deck to a small round over the base in the one quarter view; their size isn't read.","via":"harvest"}}]},"deck_x":{"label":"The footprint's middle along the deck, ahead of the clamp's middle","kind":"length","measurements":[{"id":"as-1-3","value":-0.01,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{midwest-mk2-qd-t2-lower-13.deck_x}","via":"harvest"},"note":"The 1/3 height's reading, the only straight view of the deck over the base."}],"note":"No straight side view of this height is on file: the deck over the base is the 1/3 height's, whose two straight side views are the only ones of any MK2 QD (one deck and one base in the maker's pictures of every height), said in the part's approximations."},"mount_length":{"label":"Clamp length along the rail (at its foot)","kind":"length","measurements":[{"id":"as-1-3","value":1.405,"unit":"in","pm":0.025,"source":{"type":"derived","expr":"{midwest-mk2-qd-t2-lower-13.mount_length}","via":"harvest"},"note":"The 1/3 height's reading, the only straight view of the base."}],"note":"No straight side view of this height is on file: its clamp base is the 1/3 height's, whose two straight side views are the only ones of any MK2 QD (one base in the maker's pictures of every height), said in the part's approximations."},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"metal","value":2.55,"unit":"oz","pm":0.5,"source":{"type":"derived","basis":"The model's volume: the aluminium 1.5705 cubic inches as the maker's 6061 (std.density.aluminium, 0.098 lb a cubic inch) and the steel 0.02 (the lock button, the nut's screw, the shaft in its slot) as steel (std.density.steel), from pipeline/blender/midwest_mk2_qd_t2.py's manifest. The ± is a fifth: the widths across it are the 1/3's assumptions."}}],"note":"No page gives a weight for the MK2 at this height. Weighed by its metal as modelled (CLAUDE.md: a piece no page gives a weight for), on the same assumptions as the 1/3's (its widths across)."}}},{"subject":"midwest-mk2-qd-t2-low","title":"Midwest Industries MK2 QD T2 Aimpoint Mount, Low (MI-MK2-QDT2L)","dimensions":{"deck_above_rail":{"label":"The deck's top (where the dot's base sits) above the rail's top","kind":"length","measurements":[{"id":"photo","value":0.525,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-low 0827ad6efb3f (Midwest Industries' MI-MK2-QDT2L, also its picture for the Low option: this mount from the front right and above, the lever closed, 1280 x 1280) against references/midwest-mk2-qd-t2-lower-13 5fbbfa2e9c84 (the 1/3 height in a like pose)","scaleRef":"the QD lever, the same part in both pictures: its tail 255 px high here (column 100: rows 505 to 760) and 143 px in the 1/3's (column 330), for its 0.497 in at the tail (the 1/3's profiles.lever)","method":"under the deck's rear end, between its lower edge and the lever's top: 65 px of backdrop here (column 240: rows 473 to 538), 0.127 in at the lever's scale; 214 px in the 1/3's picture (column 430), 0.744 in at its lever's, where the 1/3's own figures have 0.693 (its deck plate's lower face, 0.927 over the rail, less the lever's top, 0.234): the same 7% taken off here, 0.118 in. The lever's top (0.234) and that and the deck plate (0.173)","via":"harvest"}}],"note":"\"Low\", \"keeps the optic close to the rail\": a claim the test holds the reading to (a T-2 on it stands lower than on the 1/3 height, below a standard rear sight's line), not a figure. The reading agrees with the picture's plain fact, that the deck plate stands on the base's top with nothing between: the 1/3's base top (0.35) and deck plate (0.173) come to 0.523."},"deck_x":{"label":"The footprint's middle along the deck, ahead of the clamp's middle","kind":"length","measurements":[{"id":"as-1-3","value":-0.01,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{midwest-mk2-qd-t2-lower-13.deck_x}","via":"harvest"},"note":"The 1/3 height's reading, the only straight view of the deck over the base."}],"note":"No straight side view of this height is on file: the deck over the base is the 1/3 height's, whose two straight side views are the only ones of any MK2 QD (one deck and one base in the maker's pictures of every height), said in the part's approximations."},"mount_length":{"label":"Clamp length along the rail (at its foot)","kind":"length","measurements":[{"id":"as-1-3","value":1.405,"unit":"in","pm":0.025,"source":{"type":"derived","expr":"{midwest-mk2-qd-t2-lower-13.mount_length}","via":"harvest"},"note":"The 1/3 height's reading, the only straight view of the base."}],"note":"No straight side view of this height is on file: its clamp base is the 1/3 height's, whose two straight side views are the only ones of any MK2 QD (one base in the maker's pictures of every height), said in the part's approximations."},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"metal","value":1.71,"unit":"oz","pm":0.35,"source":{"type":"derived","basis":"The model's volume: the aluminium 1.0299 cubic inches as the maker's 6061 (std.density.aluminium, 0.098 lb a cubic inch) and the steel 0.02 (the lock button, the nut's screw, the shaft in its slot) as steel (std.density.steel), from pipeline/blender/midwest_mk2_qd_t2.py's manifest. The ± is a fifth: the widths across it are the 1/3's assumptions. Within a hundredth of an ounce of Primary Arms' 1.7 ounces for the older generation's QD Low (MI-QDT1-L), another product: not used."}}],"note":"No page gives a weight for the MK2 Low. Primary Arms gives 1.7 ounces for the older generation's QD Low (MI-QDT1-L), another product. Weighed by its metal as modelled, on the same assumptions as the 1/3's (its widths across)."}}},{"subject":"midwest-mk2-qd-t2-lower-13","title":"Midwest Industries MK2 QD T2 Aimpoint Mount, Lower 1/3 Cowitness (MI-MK2-QDT21/3)","dimensions":{"deck_above_rail":{"label":"The deck's top (where the dot's base sits) above the rail's top","kind":"length","measurements":[{"id":"photo","value":1.1,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-lower-13 9aa8e9d3f620 (MI-MK2-QDT213-ivr, the mount with a T-2 on it, straight right side) and 723bb889a675 (MI-MK2-QDT213-l, the mount alone, straight left side)","scaleRef":"in the dot's photo the T-2 (342.6 px/in: its 68 mm and its windage cap, ledger aimpoint-micro-t-2), its axis at row 416 (the middle of both end rings); in the left view the deck's length as read in the dot's photo (deck_length, 1.985 in, over the deck's 736 px: 370.8 px/in)","method":"The dot's base, which the deck's side lips hide, is the T-2's axis less its own axis over its base (aimpoint-micro-t-2.axis_above_base, 0.589 in: row 617.8), 0.049 in under the lips' top (row 601). The rail's top, which no side view shows, is taken at the axis of the clamp's cross shaft: the centre of the 12-sided adjustment nut on it in the left view (row 806, its rings' centre), 1.162 in under the lips' top there (row 375), and 0.018 in under the rail's top as a shaft lying in a rail slot is (its foot on the slot's floor, std.picatinny.slot_depth 0.118, its diameter assumed between 0.15 and 0.25 in: ± 0.03). 1.162 - 0.049 - 0.018. The ± is the T-2's 0.037 over its base, the shaft's 0.03 and the scale's 2%. Checked in the maker's quarter view of the pair from the front right (13199957f5cb): the base's front end face, the far jaw's notch for the rail's head in it, puts the rail's top at row 994 in the side view by the face's own proportions, within 0.02 in of this","via":"harvest"}}],"note":"The maker gives no height for this mount, only its name, \"1/3 Cowitness\" (the page's option; its feature line: \"Available in Low, Lower 1/3 Cowitness, Absolute Cowitness, and NV 2.26” height\"), and Primary Arms the words \"This is the lower 1/3 cowitness height, which sets the optic higher so your iron sights appear in the lower third of the optic window.\" No dot is named for any height. Read here on the maker's photographs: a claim the test holds the reading to (a T-2 on it stands higher than a standard rear sight's 1.41 to 1.42 in), not a figure. A lead, not a source: a forum post the harvester was refused (ar15.com) is quoted by a search result as \"Midwest Industries is 1.65 for lower 1/3 height\", of no named model; this reading puts a T-2's axis at 1.69."},"deck_lip_height":{"label":"The deck's two side lips: their top over the deck's top, where the dot's base sits","kind":"length","measurements":[{"id":"photo","value":0.049,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-lower-13 9aa8e9d3f620 (Midwest Industries' MI-MK2-QDT213-ivr: this mount with a Micro T-2 on it, straight right side on white, 1280 x 1280, muzzle to the right. The dot is named on no page; it is an Aimpoint Micro T-2 by its outline and controls, matched against Aimpoint's own right profile of 200198 (references/aimpoint-micro-t-2 6738645c90b1): the intensity switch with its INTENSITY arrow, the windage cap with its two pins behind it, the elevation turret in its housing, without lens covers)","scaleRef":"the T-2 in the same photo: its two ends 934 px apart (x 172 to 1106) for the sheet's 68 mm \"Sight Only\" (aimpoint-micro-t-2.sight_length: 348.9 px/in), and its windage cap 182 px across (row 425, x 345 to 527) for aimpoint-micro-t-2.windage_od, 0.541 in (336.4 px/in): the mean, 342.6 px/in, ± 2%. The two disagree by 3.7%: whether the rings at the dot's ends are the bare sight's own isn't certain. The dot's axis is the middle of each end ring (rows 230 to 600 and 263 to 570: 415 and 416.5, the photo level within a pixel and a half)","method":"the deck's top edge in the side view (the lips' top: row 601, where the silhouette steps in from the dot's 283 to 1088 to the deck's 292 to 975) over the T-2's base as its axis puts it (row 617.8): 16.8 px. The ± is the T-2's own over its base","via":"harvest"}}],"note":"Two lips along the deck's long sides that locate the dot's base between them (every quarter view: 5fbbfa2e9c84, c57e405080b1, ad7a9c06e6ce). Not drawn (the part's approximations): the three dots on file are drawn with bases as wide as their housings, wider than the deck, and the lips would stand in them."},"deck_x":{"label":"The footprint's middle along the deck, ahead of the clamp's middle","kind":"length","measurements":[{"id":"photo","value":-0.01,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-lower-13 723bb889a675 (left view) and caa89ca71b96 (right view)","scaleRef":"each view's deck length as deck_length (370.8 and 362.2 px/in)","method":"the deck's ends (left view: x 237 and 973, middle 605; right view: 332 and 1051, middle 691.5) against the base's (left: 341 and 862, middle 601.5; right, its foot under the lever: 439 and 951, middle 695): the deck's middle 3.5 px behind the base's in both, 0.009 in","via":"harvest"}}],"note":"The deck's middle over the clamp base's middle, in both straight side views: the four holes and the lug are about the deck's middle (the cross-bolt MK2's view from below: the holes' middle 3 px off the deck's in 1235)."},"deck_length":{"label":"The deck's length along the rail (the plate the dot sits on)","kind":"length","measurements":[{"id":"photo","value":1.985,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-lower-13 9aa8e9d3f620 (Midwest Industries' MI-MK2-QDT213-ivr: this mount with a Micro T-2 on it, straight right side on white, 1280 x 1280, muzzle to the right. The dot is named on no page; it is an Aimpoint Micro T-2 by its outline and controls, matched against Aimpoint's own right profile of 200198 (references/aimpoint-micro-t-2 6738645c90b1): the intensity switch with its INTENSITY arrow, the windage cap with its two pins behind it, the elevation turret in its housing, without lens covers)","scaleRef":"the T-2 in the same photo: its two ends 934 px apart (x 172 to 1106) for the sheet's 68 mm \"Sight Only\" (aimpoint-micro-t-2.sight_length: 348.9 px/in), and its windage cap 182 px across (row 425, x 345 to 527) for aimpoint-micro-t-2.windage_od, 0.541 in (336.4 px/in): the mean, 342.6 px/in, ± 2%. The two disagree by 3.7%: whether the rings at the dot's ends are the bare sight's own isn't certain. The dot's axis is the middle of each end ring (rows 230 to 600 and 263 to 570: 415 and 416.5, the photo level within a pixel and a half)","method":"the deck plate's two ends under the dot, rows 613 to 658: x 294 to 974, 680 px","via":"harvest"}},{"id":"bottom","value":1.946,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-lower-13 a5752dc6e59d (MI-MK2T213_bottom: the CROSS-BOLT MK2 T2 mount's 1/3 height, MK2T2AIMPO-2, a product of its own, straight from below, 1280 x 1280: the deck's underside round its clamp, the deck's four holes through it, cast 'T2 1/3')","scaleRef":"the clamp's two hooks seen from below, 475 px apart (y 390 to 865) for the rail's lower gauge line, std.picatinny.bevel_width 0.748 in (635 px/in): where the hooks come in to under the rail","method":"the deck's ends seen from below past the clamp, x 22.5 to 1257.5: 1235 px. The cross-bolt MK2's deck, another product's: whether its deck is this one's is what the agreement says","via":"harvest"}}],"adopt":{"from":"photo","reason":"Read on this mount, scaled by the dot on it; the cross-bolt mount's deck, scaled by its hooks as the rail's lower gauge line, is 2% shorter, inside the two readings' ±: the deck is one plate in both products by this, and the hooks may stand a little wider than the line."}},"deck_width":{"label":"The deck's width across the rifle","kind":"length","measurements":[{"id":"bottom","value":0.897,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-lower-13 a5752dc6e59d (MI-MK2T213_bottom: the CROSS-BOLT MK2 T2 mount's 1/3 height, MK2T2AIMPO-2, a product of its own, straight from below, 1280 x 1280: the deck's underside round its clamp, the deck's four holes through it, cast 'T2 1/3')","scaleRef":"the deck's own length there (1235 px) as deck_length","method":"the plate's two long sides at column 60, past the clamp: rows 362 and 919, 557 px: 0.452 of its length","via":"harvest"}}],"note":"No straight view of this mount from above, below or an end is on file (its quarter views only): read on the cross-bolt MK2's view from below, whose deck's length agrees with this one's (deck_length)."},"deck_hole_spacing":{"label":"The deck's screw holes: their spacing along the rail (two at each end)","kind":"length","measurements":[{"id":"bottom","value":1.418,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-lower-13 a5752dc6e59d (MI-MK2T213_bottom: the CROSS-BOLT MK2 T2 mount's 1/3 height, MK2T2AIMPO-2, a product of its own, straight from below, 1280 x 1280: the deck's underside round its clamp, the deck's four holes through it, cast 'T2 1/3')","scaleRef":"the deck's own length there (1235 px) as deck_length","method":"the four holes through the plate either side of the clamp: their middles at x 196 and 1078 (each hole's two edges along row 520 and column 190), 882 px. Four holes, two at each end, in the quarter views of this mount too (c57e405080b1, 165f8d951a1d)","via":"harvest"}}]},"deck_hole_across":{"label":"The deck's screw holes: their spacing across the rifle","kind":"length","measurements":[{"id":"bottom","value":0.4,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-lower-13 a5752dc6e59d (MI-MK2T213_bottom: the CROSS-BOLT MK2 T2 mount's 1/3 height, MK2T2AIMPO-2, a product of its own, straight from below, 1280 x 1280: the deck's underside round its clamp, the deck's four holes through it, cast 'T2 1/3')","scaleRef":"the deck's own length there (1235 px) as deck_length","method":"the holes' middles at rows 517 and 766 (column 190), 249 px","via":"harvest"}}]},"deck_hole_d":{"label":"The deck's screw holes: their diameter","kind":"length","measurements":[{"id":"bottom","value":0.129,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-lower-13 a5752dc6e59d (MI-MK2T213_bottom: the CROSS-BOLT MK2 T2 mount's 1/3 height, MK2T2AIMPO-2, a product of its own, straight from below, 1280 x 1280: the deck's underside round its clamp, the deck's four holes through it, cast 'T2 1/3')","scaleRef":"the deck's own length there (1235 px) as deck_length","method":"each hole's edges: 80 px across (rows 477 to 557.5 and 725 to 806.5; columns 1038.5 to 1118)","via":"harvest"}}]},"mount_length":{"label":"Clamp length along the rail (at its foot)","kind":"length","measurements":[{"id":"left","value":1.405,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-lower-13 723bb889a675 (MI-MK2-QDT213-l: the mount alone, straight left side on white, 1280 x 1280, muzzle to the left: the adjustment nut in its pocket, the lever's tail behind)","scaleRef":"the deck's length as deck_length, 736 px (370.8 px/in)","method":"the base block's two end faces, rows 747 to 835: x 341 to 862, 521 px","via":"harvest"}},{"id":"right","value":1.414,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-lower-13 caa89ca71b96 (MI-MK2-QDT213-r: the mount alone, straight right side on white, 1280 x 1280, muzzle to the right, the lever closed along the base)","scaleRef":"the deck's length as deck_length, 719 px (362.2 px/in)","method":"the base's foot under the lever, rows 890 to 900: x 439 to 951, 512 px","via":"harvest"}}],"adopt":{"from":"left","reason":"The base block itself, end to end, on the side with nothing in front of it; the right side's foot is the lever side's jaw, 0.01 in longer, within both readings."},"note":"The clamp base, from its rear face to its front face: the lever's tail reaches 0.5 in further back beside it (the right view) and isn't counted."},"clamp_below_rail":{"label":"The base's foot below the rail's top (the nut's side)","kind":"length","measurements":[{"id":"left","value":0.277,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-lower-13 723bb889a675 (MI-MK2-QDT213-l: the mount alone, straight left side on white, 1280 x 1280, muzzle to the left: the adjustment nut in its pocket, the lever's tail behind)","scaleRef":"the deck's length as deck_length (370.8 px/in)","method":"the base's foot (row 902) under the cross shaft's axis (the nut's centre, row 806): 96 px, and the rail's top 0.018 in over the axis (deck_above_rail's method)","via":"harvest"}}]},"base_top_above_rail":{"label":"The base block's top over the rail's top, where the web stands on it","kind":"length","measurements":[{"id":"left","value":0.35,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-lower-13 723bb889a675 (MI-MK2-QDT213-l: the mount alone, straight left side on white, 1280 x 1280, muzzle to the left: the adjustment nut in its pocket, the lever's tail behind)","scaleRef":"the deck's length as deck_length (370.8 px/in)","method":"the base's top face either side of the web's flare (rows 676 behind it and 668 ahead of it: 0.33 and 0.35 over the rail's top as deck_above_rail places it, row 799.3; the traced outline has 0.337 and 0.359)","via":"harvest"}}]},"deck_thickness":{"label":"The deck plate's lower face under the deck's top (where the dot's base sits)","kind":"length","measurements":[{"id":"sides","value":0.173,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-lower-13 723bb889a675 (left view) and caa89ca71b96 (right view)","scaleRef":"each view's deck length as deck_length (370.8 and 362.2 px/in)","method":"the deck plate's lower flats at its ends (row 455 in both) under the lips' top (rows 376 and 371), less the lips' height (deck_lip_height): 0.164 and 0.183. The dot's photo, taken from above the mount, reads it deeper (0.199) and isn't used","via":"harvest"}}]},"web_groove_spacing":{"label":"The two grooves down each flank of the web, either side of its oval panel: their spacing along the rail","kind":"length","measurements":[{"id":"left","value":0.426,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-lower-13 723bb889a675 (MI-MK2-QDT213-l: the mount alone, straight left side on white, 1280 x 1280, muzzle to the left: the adjustment nut in its pocket, the lever's tail behind)","scaleRef":"the deck's length as deck_length (370.8 px/in)","method":"the grooves' middles at x 532 and 690 (rows 500 to 650), 158 px, about the web's middle (608.5) within 2.5 px","via":"harvest"}}]},"web_groove_width":{"label":"The web's flank grooves: their width","kind":"length","measurements":[{"id":"left","value":0.038,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-lower-13 723bb889a675 (MI-MK2-QDT213-l: the mount alone, straight left side on white, 1280 x 1280, muzzle to the left: the adjustment nut in its pocket, the lever's tail behind)","scaleRef":"the deck's length as deck_length (370.8 px/in)","method":"each dark band 14 px across (525 to 539, 683 to 697)","via":"harvest"}}]},"nut_across":{"label":"The 12-sided adjustment nut, across its flats","kind":"length","measurements":[{"id":"left","value":0.504,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-lower-13 723bb889a675 (MI-MK2-QDT213-l: the mount alone, straight left side on white, 1280 x 1280, muzzle to the left: the adjustment nut in its pocket, the lever's tail behind)","scaleRef":"the deck's length as deck_length (370.8 px/in)","method":"its top flat (row 713) to its bottom flat (row 900) about its centre (row 806): 187 px","via":"harvest"}}],"note":"The maker's sheet: \"Rotate the 12 sided adjustment nut one notch at a time to get the exact tension you want.\" Its twelve sides, counted on the left view: a flat at top and bottom and five corners between."},"base_half_width":{"label":"The base block's sides out from the rail's middle","kind":"length","measurements":[{"id":"assumed","value":0.49,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no straight view of this mount from an end, above or below is on file. In the maker's quarter view from the front right (13199957f5cb) the base's left face stands a little outside the deck's left edge (deck_width), and its jaws must hold the rail's head (0.835 in) with walls round it.","via":"harvest"}}]},"web_width":{"label":"The web between the deck and the base, across the rifle","kind":"length","measurements":[{"id":"assumed","value":0.5,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the web is seen across only in the quarter views (5fbbfa2e9c84, ad7a9c06e6ce), where it is about half the deck's width; no straight view of it from an end is on file.","via":"harvest"}}]},"web_groove_depth":{"label":"The web's flank grooves: how far they are cut in","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the oval panel with the maker's mark on the right flank and the plain one on the left stand between two grooves in both side views, and no view shows them in profile.","via":"harvest"}}]},"lever_thickness":{"label":"The QD lever and its jaw plate: how far they stand out from the base's right side","kind":"length","measurements":[{"id":"assumed","value":0.17,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the lever lies along the base's right side in every view, and its thickness is seen only in the quarter views (5fbbfa2e9c84, c57e405080b1), where it stands out about a third of the base's height; no view from an end is on file.","via":"harvest"}}]},"nut_thickness":{"label":"The adjustment nut: how far it stands out of its pocket in the base's left side","kind":"length","measurements":[{"id":"assumed","value":0.1,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the nut is seen face on (the left view) and in the quarter views from the left (c57e405080b1), where its face stands a little out of the base's side; no view from an end is on file.","via":"harvest"}}]},"lever_window_rear_x":{"label":"The window in the lever round its lock button: its rear end","kind":"length","measurements":[{"id":"right","value":-0.35,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-lower-13 caa89ca71b96 (MI-MK2-QDT213-r: the mount alone, straight right side on white, 1280 x 1280, muzzle to the right, the lever closed along the base)","scaleRef":"the deck's ends at x 332 and 1051 as deck_x and deck_length (362.2 px/in)","method":"the dark opening's rear end at x 568","via":"harvest"}}]},"lever_window_front_x":{"label":"The window in the lever: its front end (round)","kind":"length","measurements":[{"id":"right","value":0.297,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-lower-13 caa89ca71b96 (MI-MK2-QDT213-r: the mount alone, straight right side on white, 1280 x 1280, muzzle to the right, the lever closed along the base)","scaleRef":"as lever_window_rear_x","method":"the opening's rounded front end at x 803","via":"harvest"}}]},"lever_window_top":{"label":"The window in the lever: its top over the rail's top","kind":"length","measurements":[{"id":"right","value":0.089,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-lower-13 caa89ca71b96 (MI-MK2-QDT213-r: the mount alone, straight right side on white, 1280 x 1280, muzzle to the right, the lever closed along the base)","scaleRef":"as lever_window_rear_x, and the lips' top (row 371) at deck_above_rail + deck_lip_height","method":"the opening's top edge at row 755","via":"harvest"}}]},"lever_window_bottom":{"label":"The window in the lever: its bottom against the rail's top","kind":"length","measurements":[{"id":"right","value":-0.14,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-lower-13 caa89ca71b96 (MI-MK2-QDT213-r: the mount alone, straight right side on white, 1280 x 1280, muzzle to the right, the lever closed along the base)","scaleRef":"as lever_window_top","method":"the opening's lower edge at row 838","via":"harvest"}}]},"lever_flute_rear_x":{"label":"The three flutes across the QD lever's tail: the rearmost's middle","kind":"length","measurements":[{"id":"right","value":-1.182,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-lower-13 caa89ca71b96 (MI-MK2-QDT213-r: the mount alone, straight right side on white, 1280 x 1280, muzzle to the right, the lever closed along the base)","scaleRef":"as lever_window_rear_x","method":"the dark bands across the lever's tail along row 790 (4 rows each way), their middles at x 267, 335 and 402: three, counted on the straight view of the whole tail","via":"harvest"}}]},"lever_flute_pitch":{"label":"The lever's tail flutes: their spacing","kind":"length","measurements":[{"id":"right","value":0.187,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-lower-13 caa89ca71b96 (MI-MK2-QDT213-r: the mount alone, straight right side on white, 1280 x 1280, muzzle to the right, the lever closed along the base)","scaleRef":"as lever_window_rear_x","method":"x 267 to 402 over two spacings: 67.5 px","via":"harvest"}}]},"lever_flute_width":{"label":"The lever's tail flutes: their width","kind":"length","measurements":[{"id":"right","value":0.04,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-lower-13 caa89ca71b96 (MI-MK2-QDT213-r: the mount alone, straight right side on white, 1280 x 1280, muzzle to the right, the lever closed along the base)","scaleRef":"as lever_window_rear_x","method":"each dark band about 14 px across at half its depth of tone","via":"harvest"}}]},"jaw_groove_rear_x":{"label":"The grooves down the jaw plate at the lever's front: the rearmost's middle","kind":"length","measurements":[{"id":"right","value":0.505,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-lower-13 caa89ca71b96 (MI-MK2-QDT213-r: the mount alone, straight right side on white, 1280 x 1280, muzzle to the right, the lever closed along the base)","scaleRef":"as lever_window_rear_x","method":"the dark lines down the jaw plate along row 790, at x 878, 905 and 933: three, between four ribs","via":"harvest"}}]},"jaw_groove_pitch":{"label":"The jaw plate's grooves: their spacing","kind":"length","measurements":[{"id":"right","value":0.076,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-lower-13 caa89ca71b96 (MI-MK2-QDT213-r: the mount alone, straight right side on white, 1280 x 1280, muzzle to the right, the lever closed along the base)","scaleRef":"as lever_window_rear_x","method":"x 878 to 933 over two spacings: 27.5 px","via":"harvest"}}]},"jaw_groove_width":{"label":"The jaw plate's grooves: their width","kind":"length","measurements":[{"id":"right","value":0.022,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-lower-13 caa89ca71b96 (MI-MK2-QDT213-r: the mount alone, straight right side on white, 1280 x 1280, muzzle to the right, the lever closed along the base)","scaleRef":"as lever_window_rear_x","method":"each dark line about 8 px across","via":"harvest"}}]},"lever_groove_depth":{"label":"The lever's flutes and the jaw plate's grooves: how deep they are cut","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: both are seen face on in the right view and from the front right in the quarter views, never in profile.","via":"harvest"}}]},"lock_button_rear_x":{"label":"The lock button in the lever's window: its rear end","kind":"length","measurements":[{"id":"right","value":-0.241,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-lower-13 caa89ca71b96 (MI-MK2-QDT213-r: the mount alone, straight right side on white, 1280 x 1280, muzzle to the right, the lever closed along the base)","scaleRef":"as lever_window_rear_x","method":"the lighter block's rear end at x 608","via":"harvest"}}]},"lock_button_front_x":{"label":"The lock button: its front end","kind":"length","measurements":[{"id":"right","value":0.16,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-lower-13 caa89ca71b96 (MI-MK2-QDT213-r: the mount alone, straight right side on white, 1280 x 1280, muzzle to the right, the lever closed along the base)","scaleRef":"as lever_window_rear_x","method":"the block's front end at x 753","via":"harvest"}}]},"lock_button_top":{"label":"The lock button: its top over the rail's top","kind":"length","measurements":[{"id":"right","value":0.068,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-lower-13 caa89ca71b96 (MI-MK2-QDT213-r: the mount alone, straight right side on white, 1280 x 1280, muzzle to the right, the lever closed along the base)","scaleRef":"as lever_window_top","method":"the block's top edge at row 762.7","via":"harvest"}}]},"lock_button_bottom":{"label":"The lock button: its bottom against the rail's top","kind":"length","measurements":[{"id":"right","value":-0.114,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-lower-13 caa89ca71b96 (MI-MK2-QDT213-r: the mount alone, straight right side on white, 1280 x 1280, muzzle to the right, the lever closed along the base)","scaleRef":"as lever_window_top","method":"the block's lower edge at row 828.6","via":"harvest"}}]},"nut_rib_inner_x":{"label":"The two ribs either side of the adjustment nut on the base's left side: their inner faces, out from the nut's axis","kind":"length","measurements":[{"id":"left","value":0.26,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-lower-13 723bb889a675 (MI-MK2-QDT213-l: the mount alone, straight left side on white, 1280 x 1280, muzzle to the left: the adjustment nut in its pocket, the lever's tail behind)","scaleRef":"the traced outline's placement (profiles.side: 370.3 px/in, the deck's ends at deck_length about deck_x)","method":"the ribs' inner edges at x 501 and 694 (row 800) about the nut's centre (601): 0.271 and 0.250","via":"harvest"}}]},"nut_rib_outer_x":{"label":"The ribs either side of the nut: their outer faces, out from the nut's axis","kind":"length","measurements":[{"id":"left","value":0.4,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-lower-13 723bb889a675 (MI-MK2-QDT213-l: the mount alone, straight left side on white, 1280 x 1280, muzzle to the left: the adjustment nut in its pocket, the lever's tail behind)","scaleRef":"as nut_rib_inner_x","method":"the ribs' outer edges at x 452 and 747: 0.403 and 0.393","via":"harvest"}}]},"nut_rib_top":{"label":"The ribs either side of the nut: their top over the rail's top","kind":"length","measurements":[{"id":"left","value":0.15,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-lower-13 723bb889a675 (MI-MK2-QDT213-l: the mount alone, straight left side on white, 1280 x 1280, muzzle to the left: the adjustment nut in its pocket, the lever's tail behind)","scaleRef":"as nut_rib_inner_x","method":"their top edges at row 746 (column 476)","via":"harvest"}}]},"nut_rib_bottom":{"label":"The ribs either side of the nut: their bottom against the rail's top","kind":"length","measurements":[{"id":"left","value":-0.134,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-lower-13 723bb889a675 (MI-MK2-QDT213-l: the mount alone, straight left side on white, 1280 x 1280, muzzle to the left: the adjustment nut in its pocket, the lever's tail behind)","scaleRef":"as nut_rib_inner_x","method":"their lower edges at row 851 (column 476)","via":"harvest"}}]},"nut_rib_proud":{"label":"The ribs either side of the nut: how far they stand out of the base's side","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: they are seen face on in the left view, lit along their top and bottom edges, and from the rear left in c57e405080b1, where they stand a little out of the side; no view shows them in profile.","via":"harvest"}}]},"nut_screw_d":{"label":"The slotted screw in the adjustment nut's middle: its head's diameter","kind":"length","measurements":[{"id":"left","value":0.154,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/midwest-mk2-qd-t2-lower-13 723bb889a675 (MI-MK2-QDT213-l: the mount alone, straight left side on white, 1280 x 1280, muzzle to the left: the adjustment nut in its pocket, the lever's tail behind)","scaleRef":"the deck's length as deck_length (370.8 px/in)","method":"its head's rim across row 806: x 579.5 to 636.5, 57 px","via":"harvest"}}]},"shaft_d":{"label":"The cross shaft the lever and the nut are on: its diameter, where it crosses the rail in a slot","kind":"length","measurements":[{"id":"assumed","value":0.2,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the shaft is hidden in the base in every view (its end is the screw in the nut's middle). Taken between 0.15 and 0.25 in, which is what deck_above_rail's ± allows for where it lies in its slot.","via":"harvest"}}]},"edge_break":{"label":"The break on the aluminium's edges","kind":"length","measurements":[{"id":"assumed","value":0.012,"unit":"in","pm":0.006,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the edges read slightly round in the maker's photographs, by how much isn't read.","via":"harvest"}}]},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"buds","value":3.6,"unit":"oz","pm":0.05,"stated":"Weight 3.6 ounces","source":{"type":"spec","publisher":"retailer","name":"Bud's Gun Shop, Midwest Industries MK2 QD T2 Aimpoint Mount Lower 1/3 Co-Witness Black (MI-MK2-QDT21-3), Specifications","url":"https://www.budsgunshop.com/products/optics-mounts-rings-bases/midwest-industries-mk2-qd-t2-aimpoint-mount-lower-1-3-192705","retrieved":"2026-11-03","via":"harvest"}},{"id":"metal","value":2.08,"unit":"oz","pm":0.4,"source":{"type":"derived","basis":"The model's volume: the aluminium 1.2699 cubic inches as the maker's 6061 (std.density.aluminium, 0.098 lb a cubic inch: 1.99 oz) and the steel 0.02 (the lock button, the nut's screw, the shaft in its slot) as steel (std.density.steel: 0.09 oz), from pipeline/blender/midwest_mk2_qd_t2.py's manifest. The ± is a fifth: the widths across it are assumed."}}],"adopt":{"from":"metal","reason":"No figure of the maker's: the mount's metal as modelled, the category's rule. Bud's Gun Shop's 3.6 oz is a seller's, for a product the maker sells with a tool, and 1.5 oz over the metal: kept, not used."},"note":"The maker gives no weight for the MK2. Bud's Gun Shop gives 3.6 ounces for this SKU (MI-MK2-QDT21-3, UPC 812102035800) and calls it 7075-T6 where the maker says 6061; the maker's page says it \"Includes Midwest Industries Optic Mount Tool\", and whether Bud's figure is the mount alone or as boxed with its tool isn't said. Weighed here by its metal as modelled (CLAUDE.md: a piece no page of the maker's gives a weight for): 42% under Bud's figure. What the model may lack: the base's sides and the web's width are assumed, and the lever, its cam and the cross shaft may be steel where they are drawn as aluminium."}}},{"subject":"nordic-22rb-upper","title":"Nordic Components 22RB .22 LR upper, 16\", Black Teflon (22RB-UPPER-16-KIT)","dimensions":{"barrel_length":{"label":"Barrel length","kind":"length","measurements":[{"id":"spec","value":16,"unit":"in","source":{"type":"spec","publisher":"manufacturer","name":"Nordic Components","url":"https://nordiccomp.com/categories/nc-22rb-upper/","via":"brief"}}]},"pin_spacing":{"label":"Pin-hole spacing as read in the upper's reference photo","kind":"length","measurements":[{"id":"std","value":6.375,"unit":"in","source":{"type":"derived","expr":"{std.ar15.pin_spacing}","via":"brief"}},{"id":"photo","value":6.295,"unit":"in","source":{"type":"photo","photo":"22RB side product photo (not yet archived)","scaleRef":"not recorded in brief","method":"calibrated photo measurement","via":"brief"},"note":"Reads 1.25% short, so that photo's scale is off near the pins."}],"adopt":{"from":"std","reason":"The pins are a standard interface. Features from this photo are aligned to the lower at the pin midpoint rather than trusting its scale there."}},"bore_axis_above_pin":{"label":"Bore axis above pin centerline","kind":"length","measurements":[{"id":"coaxial","value":0.8775,"unit":"in","source":{"type":"derived","expr":"{std.ar15.bore_axis_y}","via":"user"},"note":"The standard's height: the upper's lugs fix its bore over the pins (drawing 8448524: .625 above its underside, the lug holes .251 below), in line with the receiver extension. Not measured on this upper. M2 had 0.849, the lower's photo-read axis (M6)."}]},"rail_top_above_pin":{"label":"Top rail surface above pin centerline","kind":"length","measurements":[{"id":"photo","value":2.03,"unit":"in","stated":"about 2.03 in","source":{"type":"photo","photo":"22RB side product photo (not yet archived)","scaleRef":"not recorded in brief","method":"calibrated photo measurement","via":"brief"}},{"id":"flatlay","value":2.07,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/nordic-22rb-upper d0862b6dba98 (complete rifle lying flat on its right side, photographed straight down; supplied in chat)","scaleRef":"pin frame: takedown, pivot, trigger pin and selector (Hough-refined), 49.18 px/in, rotation 1.43°, rms 0.03 in","method":"top silhouette of the receiver's rail just ahead of the charging handle (x 0–0.3 in, 2.07–2.08), neutral-colour mask; true side view, so no elevation inflation","via":"user"},"note":"Farther forward, on the handguard, the rail's top edge reads a median 2.17 (slot tops and bottoms averaged). That's 12–20 in from the pins, where lens distortion and a 0.15° rotation uncertainty add up to ~0.05 in, so the receiver reading is used."},{"id":"user","value":2.09,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/nordic-22rb-upper 14dc07bfde38, d633f1bf49ff, 8c0c57f466e0, 9c62acf0f248, 7523d9cd1b94 (the user's own 22RB lying on a tile floor, each side, from 5 to 7 ft, zoomed; 2026-10-03)","scaleRef":"the rail's 49 slots, found at mid-depth of the teeth (a projective fit to their centres: 0.3 to 0.6 px rms, 106 to 120 px/in), and the two lug holes' see-through centres, all on the centre plane; a camera pose fitted to them. Checks: the lug holes read 6.383 apart directly (+0.13%), the handguard's M-LOK slits 1.573 to 1.582 apart (40 mm), the receiver's underside 0.24 to 0.25 above the pins (the deck's 0.254)","method":"the teeth's tops above the pin line in the two photos taken square on (the lens 0.5 in from the bore's line): 2.088 and 2.093, 0.011 taken off for the rail's near edge","via":"user"}}],"adopt":{"from":"user","reason":"The user's own upper in two photos taken square on, the pins and the rail in one pose (2.088, 2.093). The flat-lay's 2.07 ± 0.04 agrees; the brief's 2.03 doesn't."}},"receiver_height_with_rail":{"label":"Upper receiver height including rail","kind":"length","measurements":[{"id":"photo","value":1.77,"unit":"in","source":{"type":"photo","photo":"22RB side product photo (not yet archived)","scaleRef":"not recorded in brief","method":"calibrated photo measurement","via":"brief"}},{"id":"right-photo","value":1.817,"unit":"in","pm":0.058,"source":{"type":"photo","photo":"references/nordic-22rb-upper 24d592636074 (right side, Nordic NC22-16-Upper-V2, 1200 px)","scaleRef":"rail model 02-24d592636074.calib.json along the rail (tilt 0.37° removed) and its local scale across it, anchored at the takedown lug","method":"rail tooth tops to the receiver's underside, medians over x 1–5.5 (between the lugs), from the traced outline (tools/trace.py target)","via":"harvest"}}],"adopt":{"from":"right-photo","reason":"Photo on file, traced; the brief's 1.77 (photo not archived) agrees within the ±."},"note":"The right-side product photo (24d592636074) isn't elevated at the receiver (its underside lands on the lower's deck); the left one (2b348f6a5149) reads high."},"handguard_height":{"label":"Handguard height","kind":"length","measurements":[{"id":"photo","value":1.91,"unit":"in","source":{"type":"photo","photo":"22RB side product photo (not yet archived)","scaleRef":"not recorded in brief","method":"calibrated photo measurement","via":"brief"}},{"id":"flatlay","value":2.039,"unit":"in","pm":0.062,"source":{"type":"photo","photo":"references/nordic-22rb-upper d0862b6dba98 (complete rifle lying flat on its right side, photographed straight down; supplied in chat)","scaleRef":"pin frame: takedown, pivot, trigger pin and selector (Hough-refined), 49.2 px/in","method":"rail tooth tops (the top edge's max over 0.4 in windows) to the handguard's underside, medians over x 11–18.5 (clear of the scope's rings), from the traced outline (tools/trace.py target); segmentation: saturation < 0.35 and value < 0.5, or value < 0.2 (the black handguard reflects the wood); ± includes the lens's ~1.2% compression across the axis there, left uncorrected","via":"user"},"note":"Replaces the M2 reading of 1.85, whose mask lost the handguard's reflective upper half."},{"id":"right-photo","value":2.038,"unit":"in","pm":0.058,"source":{"type":"photo","photo":"references/nordic-22rb-upper 24d592636074 (right side, Nordic NC22-16-Upper-V2, 1200 px)","scaleRef":"rail model 02-24d592636074.calib.json along the rail (tilt 0.37° removed) and its local scale across it, anchored at the takedown lug","method":"rail tooth tops to the handguard's underside, medians over x 9–18.5, from the traced outline (tools/trace.py target). The receiver in the same photo lands on the lower's deck (0.240 vs 0.254) and on the rail top (2.058 vs 2.07), so the view isn't elevated","via":"harvest"}},{"id":"end-view","value":1.971,"unit":"in","pm":0.016,"source":{"type":"photo","photo":"references/nordic-22rb-upper 5dc13057dabd (Aawee: the NCT3 handguard, straight end-on, transparent background)","scaleRef":"nordic-22rb-upper.handguard_width (1.602 in, the listed 40.7 mm across the side flats) over the outline's 321 px extent, 200.4 px/in","method":"the traced end section's height, bottom flat to rail top (profiles.front, tools/trace.py's check); ± is a pixel at each end and the width's. The rail's end may sit a little behind the near face and read slightly small","via":"harvest"},"note":"Recorded as a check on the outline since M5 (\"1.98 from its end view\"); a measurement of the height in its own right, and the only one that isn't a side photo's."},{"id":"on-axis","value":2.0059,"unit":"in","pm":0.045,"source":{"type":"derived","expr":"{.handguard_rail_top_above_pin} - {.handguard_bottom_y}","via":"harvest"},"note":"What is drawn: the handguard's own rail top over its underside, the underside half the width below the barrel's axis."},{"id":"user","value":2.02,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/nordic-22rb-upper 14dc07bfde38, d633f1bf49ff (the user's own 22RB lying on a tile floor, left and right side, square on from 5 to 7 ft, zoomed; 2026-10-03); references/nordic-22rb-upper 2cd733a9d284, 0dad4e900d85 (the user's own 22RB, the muzzle end straight on, the rail at the bottom, a tape across above; 2026-10-03)","scaleRef":"the rail's 49 slots and the two lug holes' see-through centres, all on the centre plane, in one fitted camera pose (rail_slot0_x#user); in the end views, the rail head's 0.835","method":"the bottom flat to the teeth's tops: 2.01 and 2.02 in the two side photos taken square on (the underside 0.063 to 0.083 above the pins, the tops 2.088 and 2.093); 2.02 to 2.03 end on","via":"user"}}],"adopt":{"from":"on-axis","reason":"The height the handguard has where it is drawn, centred on the barrel under its own rail; the end view reads the same (1.971 ± 0.016). The two side photos read 2.04, within their ± 0.06 of it: their undersides are where this puts them (0.088 in the right photo's frame) and their rail tops along the handguard read 0.05 high (2.124 against 2.07), the trend a lens gives (handguard_rail_step). The brief's 1.91 (photo not archived) stays visible."},"note":"Rail tooth tops to the handguard's underside. M2 read 1.85 from the flat-lay with a mask (saturation < 0.35 and value < 0.5) that lost the black handguard's upper half where it reflects the wood; re-traced in M3 (tools/trace.py), the flat-lay and the product's right-side photo agree on 2.04. The left product photo reads high (2.10: its receiver sits 0.18 below the lower's deck, so its heights aren't used)."},"muzzle_shoulder_x":{"label":"Muzzle thread shoulder ahead of the takedown pin (where a muzzle device seats)","kind":"length","measurements":[{"id":"seam","value":21.134,"unit":"in","source":{"type":"derived","expr":"{.muzzle_ahead_of_pin} - {nordic-thread-protector.length}","via":"harvest"}}],"note":"The photos show the upper as shipped, its thread protector on: the shoulder is the protector's seam with the barrel, so it is the protector's face less the protector's length. A suppressor or flash hider seats here."},"muzzle_face_behind_protector":{"label":"Muzzle face, behind the thread protector's front face","kind":"length","measurements":[{"id":"three-quarter","value":0.005,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/nordic-22rb-upper c280084b0a6e (Nordic: the 22RB's muzzle end, three-quarter view, 1200 px)","scaleRef":"the protector's front face, 157 px across its long axis, taken as nordic-thread-protector.od (0.717): 218.5 px/in. The bore's ellipse (short axis 0.42 of the long) puts the view 65 degrees off the bore axis","method":"the crop stretched along the ellipses' short axis, so circles about the bore axis are circles again with their centres displaced by depth (0.002 in of depth a pixel). The protector's mouth and the outer edge of the barrel's end face, read off radial profiles and off the stretched picture, have centres 0.5 px and 4 px apart: flush, to 0.009 in inside. An automatic edge tracker jumped between the rings and wasn't used (references/nordic-22rb-upper/muzzle_recess.py). ± covers the two readings","via":"harvest"}}],"note":"The protector is a threaded sleeve, open at both ends (Nordic's photo of it alone, 9056e2073f45): what shows in its mouth on the rifle is the barrel's own end face and crown."},"muzzle_thread_length":{"label":"Muzzle thread: the shoulder to the muzzle face","kind":"length","measurements":[{"id":"protector","value":0.465,"unit":"in","pm":0.022,"source":{"type":"photo","photo":"references/nordic-22rb-upper 2b348f6a5149 (left side, NC22RB-UPPER-16-KIT_3_HR)","scaleRef":"the protector's length as that photo has it (nordic-thread-protector.length#left, 0.47 ± 0.02)","method":"the protector's length less the muzzle face's setback in its mouth (muzzle_face_behind_protector, 0.005)","via":"harvest"},"note":"The protector seats on the shoulder (its seam with the barrel) and the muzzle face is flush with its front or just inside. Until 2026-10-03 this was the adopted figure, derived from the protector's length; with the bare thread measured the dependence runs the other way (nordic-thread-protector.length#thread)."},{"id":"nc22-owner","value":0.48,"unit":"in","pm":0.02,"stated":"The length of of the barrel before it widens to the larger OD, is roughly 0.48\" long.","source":{"type":"spec","publisher":"forum","name":"Northeast Shooters forum, 'Nordic NC22 .22lr AR Review', post 15 (2020-10-12): an owner of Nordic's NC22, the 22RB's predecessor","url":"https://www.northeastshooters.com/xen/threads/nordic-nc22-22lr-ar-review.120034/","retrieved":"2026-10-01","via":"harvest"},"note":"A different, older Nordic .22 upper, which shipped with a flash hider. The same post: \"The threads are 1/2x28 but the length of the threads is 0.400\\\"\". 'Roughly': the ± is mine."},{"id":"user","value":0.506,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/nordic-22rb-upper c0e654135597 (the user's own 22RB, the bare muzzle from the side, the thread protector off; 2026-10-03)","scaleRef":"the thread's own pitch, 1/2-28 as the part states it (28 to the inch: 34 to 35 px a pitch); it checks against the thread's major diameter, 315 px over that pitch = 0.49 to 0.50 in","method":"on the lower silhouette, in the barrel's mid-plane: the muzzle face at px 964 ± 2; a plain pilot 0.031 long; ten crests (984 to 1192: nine pitches, 0.321); the thread running out at 1214, 0.385 from the face; a plain relief smaller than the thread, 0.120 long; the shoulder at 1293 ± 3, the same column top and bottom. ± is the two end picks and the pitch's 3% growth along the photo; the crest count is exact. The floor tape beside it reads 0.532 over the same span, which is 0.506 from a lens 16 in up","via":"user"},"note":"Longer than the .400 SilencerCo makes the Sparrow 22 for, shorter than its spacer's .600 to .650."}],"adopt":{"from":"user","reason":"The barrel's own threaded end, bare, scaled by its own thread. The protector's length less the face's setback (0.465) and the NC22 owner's 0.48 were its length seen from outside."},"note":"How far the barrel's reduced, threaded end stands ahead of its shoulder: a muzzle device made for a given thread length shoulders only if this is no longer. Nordic doesn't publish it. How much of it carries thread: on the user's own barrel (2026-10-03) a plain pilot 0.03 long, thread to 0.385 from the face, then a relief 0.12 long to the shoulder; the owner of an older Nordic NC22 gives 0.400 of roughly 0.48."},"muzzle_thread_major_d":{"label":"Muzzle thread: its major diameter (its crests)","kind":"length","measurements":[{"id":"tdp","value":0.4957,"unit":"in","pm":0.0033,"stated":"1/2-28 UNEF-2A MAJOR DIA .4989/.4924","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213","via":"user"},"note":"The middle of the two limits, ± half their spread."},{"id":"user","value":0.485,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/nordic-22rb-upper c0e654135597 (the user's own 22RB, the bare muzzle from the side, the thread protector off; 2026-10-03)","scaleRef":"the thread's own pitch on the lower silhouette, 28 to the inch: ten crests from column 982.5 to 1188 (22.83 px each, 639 px/in); the upper silhouette's are 22.6","method":"crest to crest across the silhouette: the upper crests' tips at row 1140 ± 1, the lower at 1450 ± 1: 310 px, 13.6 pitches (a 1/2 in thread of 28 to the inch is 13.9 across; 1/2-20 would be 10, 7/16-28 12.2). ± is 3 px of the edges and the pitch's 1% between the two silhouettes","via":"user"}}],"adopt":{"from":"tdp","reason":"The thread the barrel is sold with, at the Army drawing's limits for it; the photo's 0.485 ± 0.01 is the crests' silhouette, 2% under and inside its own ±."},"note":"The Army barrel's 1/2-28 thread, for the 1/2-28 this barrel is sold with: what the model's thread is drawn at. Neither figure of the drawing is a measurement of this barrel; the user's photo of it bare is, and reads its crests 2% under the drawing's middle, inside what its edges and its scale can tell."},"muzzle_thread_minor_d":{"label":"Muzzle thread: its minor diameter (its roots)","kind":"length","measurements":[{"id":"tdp","value":0.4551,"unit":"in","pm":0.002,"stated":"MINOR DIA .4551 MAX","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213","via":"user"},"note":"A maximum: the ± is mine, as bcm-16-mid-barrel.thread_minor_d has it."},{"id":"user","value":0.453,"unit":"in","pm":0.007,"source":{"type":"photo","photo":"references/nordic-22rb-upper c0e654135597 (the user's own 22RB, the bare muzzle from the side, the thread protector off; 2026-10-03)","scaleRef":"the thread's own crests in the same view, top and bottom of its silhouette (rows 1140 and 1450: 310 px across), taken as its major diameter (muzzle_thread_major_d, 0.4957)","method":"the roots' edges in the same view: the upper ones at rows 1153 to 1156.6 in six columns between crests (1154 ± 1.5), the lower at 1437.5: 283.5 px, 0.9145 of the crests'. A helix's roots are partly hidden behind the next flank in a silhouette, which would read them large, not small. ± is the edges and the major diameter's own","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's figure for the thread, which the user's barrel reads within 0.002 of."},"note":"The drawing gives a maximum and the model draws the roots there. On the user's barrel the roots read 0.9145 of the crests, which at the drawing's major diameter is 0.453."},"muzzle_thread_pitch":{"label":"Muzzle thread: its pitch","kind":"length","measurements":[{"id":"tdp","value":0.03571,"unit":"in","pm":0.00005,"stated":"1/2-28 UNEF-2A","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213","via":"user"}},{"id":"nc22-owner","value":0.03571,"unit":"in","pm":0.00005,"stated":"The threads are 1/2x28 but the length of the threads is 0.400\"","source":{"type":"spec","publisher":"forum","name":"Northeast Shooters forum, 'Nordic NC22 .22lr AR Review', post 15 (2020-10-12): an owner of Nordic's NC22, the 22RB's predecessor","url":"https://www.northeastshooters.com/xen/threads/nordic-nc22-22lr-ar-review.120034/","retrieved":"2026-10-01","via":"harvest"}}],"adopt":{"from":"tdp","reason":"One thread by both; the drawing is the one that defines it."},"note":"28 threads to the inch. Nordic's own page isn't on file with the words; the NC22's owner states them, the Army's 1/2-28 is the same thread, and the user's photo counts 13.6 pitches to the thread's diameter, which is 1/2-28 and no other common thread (see muzzle_thread_major_d#user)."},"muzzle_thread_start":{"label":"Muzzle thread: the muzzle face to its first crest","kind":"length","measurements":[{"id":"user","value":0.029,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/nordic-22rb-upper c0e654135597 (the user's own 22RB, the bare muzzle from the side, the thread protector off; 2026-10-03)","scaleRef":"the thread's own pitch on the lower silhouette (22.83 px, 639 px/in)","method":"on the lower silhouette: the face at column 964.5 ± 2 (964 in the reading of 2026-10-03, 965 here), the first crest's tip at 982.5 to 984: 18 to 19.5 px. The 2026-10-03 reading gave 0.031 (muzzle_thread_length#user: 'a plain pilot 0.031 long')","via":"user"}}],"note":"Ahead of the first crest the end is plain: a pilot a little under the roots' diameter (muzzle_pilot_d), half a pitch of lead-in flank behind it. The helix puts the first crest of the upper silhouette half a pitch nearer the face (column 975): the model's thread is rings, placed where the lower silhouette has its crests."},"muzzle_thread_end":{"label":"Muzzle thread: the muzzle face to where the thread runs out","kind":"length","measurements":[{"id":"user","value":0.385,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/nordic-22rb-upper c0e654135597 (the user's own 22RB, the bare muzzle from the side, the thread protector off; 2026-10-03)","scaleRef":"the thread's own pitch on the lower silhouette (22.83 px, 639 px/in; 23.1 in the reading of 2026-10-03)","method":"the last full crest at column 1188 to 1192, the thread running out at 1214 ± 3 (the reading of 2026-10-03, looked at again on the same crop: muzzle_thread_length#user)","via":"user"}}],"note":"Behind it the end is a plain relief (muzzle_relief_d) to the shoulder: 0.121 in of the 0.506. Ten full crests and the run-out of an eleventh."},"muzzle_relief_d":{"label":"Muzzle thread: the relief's diameter, between the thread and the shoulder","kind":"length","measurements":[{"id":"user","value":0.441,"unit":"in","pm":0.007,"source":{"type":"photo","photo":"references/nordic-22rb-upper c0e654135597 (the user's own 22RB, the bare muzzle from the side, the thread protector off; 2026-10-03)","scaleRef":"the thread's own crests in the same view, top and bottom of its silhouette (rows 1140 and 1450: 310 px across), taken as its major diameter (muzzle_thread_major_d, 0.4957)","method":"the relief's upper edge in three columns (1225, 1255, 1270): rows 1156.9, 1157.8, 1156.9, a strong edge (40 to 100 of 255); about the axis the crests give (row 1295) that is 137.8 px, 275.6 across, 0.889 of the crests'. ± is the edges and the major diameter's own","via":"user"}}],"note":"A plain neck a little under the thread's roots. Its lower edge is in the shoulder's shadow in this photo and isn't read: the diameter is its upper edge about the thread's own axis."},"muzzle_pilot_d":{"label":"Muzzle thread: the plain pilot's diameter, at the muzzle face","kind":"length","measurements":[{"id":"user","value":0.443,"unit":"in","pm":0.007,"source":{"type":"photo","photo":"references/nordic-22rb-upper c0e654135597 (the user's own 22RB, the bare muzzle from the side, the thread protector off; 2026-10-03)","scaleRef":"the thread's own crests in the same view, top and bottom of its silhouette (rows 1140 and 1450: 310 px across), taken as its major diameter (muzzle_thread_major_d, 0.4957)","method":"the pilot's edges at column 968, between the face and the first flank: rows 1157.4 and 1434.0, 277 px about the same axis (1295.7), 0.8935 of the crests'. ± is the edges and the major diameter's own","via":"user"}}]},"bore_d":{"label":"The bore, as it shows in the muzzle face","kind":"length","measurements":[{"id":"three-quarter","value":0.218,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/nordic-22rb-upper c280084b0a6e (Nordic: the 22RB's muzzle end, three-quarter view, 1200 px)","scaleRef":"the protector's face, its vertical extent = the barrel's OD (nordic-22rb-upper.barrel_od, 0.717; the protector is flush with the barrel in the side photos)","method":"the bore's vertical extent against the face's on a 4x crop, both ellipses' long axes (the view's tilt shortens them alike): 0.304 of the face","via":"harvest"}},{"id":"user","value":0.232,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/nordic-22rb-upper 2cd733a9d284 (the user's own 22RB, the muzzle end straight on, the rail at the bottom, a tape across above; 2026-10-03)","scaleRef":"the protector's own face in the same view: a circle fitted to its rim on 521 of 720 rays, 226.2 px in radius (rms 1.3), taken as nordic-thread-protector.od (0.736): 615 px/in","method":"a circle fitted to the dark hole's rim on 511 rays: 71.2 px in radius, rms 4.5 (.cache/barrel/rings.py): 0.315 of the face. The rim is ragged with the rifling's reflections in the crown, and its centre is 10 px from the face's: the dark disc takes in the crown's shadow, and reads the hole large. ± is the fit's rms on both sides","via":"user"},"note":"Kept beside the other reading, not adopted: a hole and its shadow."}],"adopt":{"from":"three-quarter","reason":"The hole's own rim, seen from the side of the axis where the crown doesn't shadow it. The user's face-on photo reads the dark disc, crown and all, 0.014 larger: inside the two ±."},"note":"The dark hole in the barrel's end face (.22 LR barrels are bored about 0.217 to 0.222 in, bore to groove: not a source). It was nordic-thread-protector.bore_d until 2026-10-06, kept there because the protector's sleeve was drawn with the hole in it; the barrel is drawn with its own bore now, right through. The lands and the grooves aren't told apart, and the crown's recess round the hole (a ring 0.36 in across in the face-on photo) isn't drawn: how deep it is isn't read."},"latch_to_muzzle":{"label":"Charging-handle latch to muzzle","kind":"length","measurements":[{"id":"model-a","value":22.6,"unit":"in","stated":"22.6–22.9 in","source":{"type":"photo","photo":"22RB side product photo (not yet archived)","scaleRef":"not recorded in brief","method":"distortion model A (which model gave which end is not recorded)","via":"brief"}},{"id":"model-b","value":22.9,"unit":"in","stated":"22.6–22.9 in","source":{"type":"photo","photo":"22RB side product photo (not yet archived)","scaleRef":"not recorded in brief","method":"distortion model B (which model gave which end is not recorded)","via":"brief"}},{"id":"harvest-left","value":22.88,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/nordic-22rb-upper 2b348f6a5149 (left side, NC22RB-UPPER-16-KIT_3_HR via Aerospace Arms)","scaleRef":"top-rail Picatinny slots: 49 slots, rms 0.001 in, drift −1.0%","method":"silhouette end to end through the cubic model, linear beyond the rail (≈2 in each end). The camera is slightly elevated; the length effect is negligible","calibration":"references/nordic-22rb-upper/*-2b348f6a5149.calib.json","via":"harvest"}},{"id":"harvest-right","value":22.56,"unit":"in","pm":0.25,"source":{"type":"photo","photo":"references/nordic-22rb-upper 24d592636074 (right side, Nordic NC22-16-Upper-V2)","scaleRef":"top-rail Picatinny slots: 37 slots, rms 0.017 in","method":"same method; 4.6 in extrapolated at the rear at 50 px/in, hence the larger ±","calibration":"references/nordic-22rb-upper/*-24d592636074.calib.json","via":"harvest"}}],"adopt":{"from":"harvest-left","reason":"Highest-quality calibration (0.001 in rail fit at 84 px/in). Agrees with the brief's upper value (22.9). The lower-resolution photo and the brief's other model sit near 22.6; calipers settle it."}},"muzzle_ahead_of_pin":{"label":"Muzzle (thread protector face) ahead of takedown pin","kind":"length","measurements":[{"id":"from-oal","value":21.245,"unit":"in","source":{"type":"derived","expr":"{asm.v1.oal_pos1} - {magpul-moe-sl-carbine.butt_behind_pin_pos1}","via":"brief"},"note":"The brief's overall length minus the position-1 butt. It's circular for an OAL test, so the photo measurements below are the independent ones. 21.43 until 2026-10-05, when it moved with the MOE SL's seat: the stock's position-1 butt was put 0.185 in further back on a photo of one installed (magpul-moe-sl-carbine.butt_behind_pin_pos1), and this is that much less."},{"id":"left","value":21.638,"unit":"in","pm":0.035,"source":{"type":"photo","photo":"references/nordic-22rb-upper 2b348f6a5149 (left side, NC22RB-UPPER-16-KIT_3_HR)","scaleRef":"rail model from 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%), anchored at takedown lug (1853.5,1074.5) = frame x 0","method":"silhouette x_max along the rail model; ± is 3× rail rms plus edge and anchor error","via":"harvest"},"note":"Most forward silhouette point: the near rim of the thread protector's flat face, which this photo sees from about 19 degrees behind square (the protector's seam shows as an arc, sag 0.122 in at the barrel's radius: references/nordic-22rb-upper/muzzle_perspective.py). If the rail model's scale is that of the plane through the bore, the face's centre is 0.12 in behind this reading; if it is that of a plane 0.25 in nearer the lens (where the lug holes' near rims are: the pin-only frame agrees with the rail model at the muzzle to 0.008 in), 0.03 in behind. Which plane it is isn't established, so the reading stands uncorrected and the ± doesn't cover the first case (M6: open)."},{"id":"right","value":21.326,"unit":"in","pm":0.076,"source":{"type":"photo","photo":"references/nordic-22rb-upper 24d592636074 (right side, Nordic NC22-16-Upper-V2)","scaleRef":"rail model from 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%), anchored at takedown lug (91.5,475.5) = frame x 0","method":"silhouette x_max along the rail model; ± is 3× rail rms plus edge and anchor error","via":"harvest"}},{"id":"user","value":21.645,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/nordic-22rb-upper 14dc07bfde38, d633f1bf49ff, 8c0c57f466e0, 9c62acf0f248, 7523d9cd1b94 (the user's own 22RB lying on a tile floor, each side, from 5 to 7 ft, zoomed; 2026-10-03)","scaleRef":"the rail's 49 slots, found at mid-depth of the teeth (a projective fit to their centres: 0.3 to 0.6 px rms, 106 to 120 px/in), and the two lug holes' see-through centres, all on the centre plane; a camera pose fitted to them. Checks: the lug holes read 6.383 apart directly (+0.13%), the handguard's M-LOK slits 1.573 to 1.582 apart (40 mm), the receiver's underside 0.24 to 0.25 above the pins (the deck's 0.254)","method":"the thread protector's front face, taken where the end's profile meets the protector's edges (at 0.86 and 0.92 of its radius: the face is seen from a little behind, so the silhouette's end bulges at the axis and its forward-most point reads 0.05 further): 21.648, 21.656, 21.637, 21.646, 21.640; ± is the pick inside the face's rounded edge (0.012), the anchor (0.007) and the scale over 21.6 in","via":"user"}}],"adopt":{"from":"user","reason":"The user's own upper in five photos, 21.637 to 21.656. The left product photo agrees (21.638); the right one reads the whole upper about 1.2% short (21.326)."}},"rear_behind_pin":{"label":"Rear of the upper (the charging handle's T's rear face, the handle home) behind the takedown pin","kind":"length","measurements":[{"id":"left","value":1.239,"unit":"in","pm":0.035,"source":{"type":"photo","photo":"references/nordic-22rb-upper 2b348f6a5149 (left side, NC22RB-UPPER-16-KIT_3_HR)","scaleRef":"rail model from 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%), anchored at takedown lug (1853.5,1074.5) = frame x 0","method":"silhouette x_min along the rail model (negated); ± is 3× rail rms plus edge and anchor error","via":"harvest"},"note":"Rearmost silhouette point (charging-handle latch)."},{"id":"right","value":1.236,"unit":"in","pm":0.076,"source":{"type":"photo","photo":"references/nordic-22rb-upper 24d592636074 (right side, Nordic NC22-16-Upper-V2)","scaleRef":"rail model from 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%), anchored at takedown lug (91.5,475.5) = frame x 0","method":"silhouette x_min along the rail model (negated); ± is 3× rail rms plus edge and anchor error","via":"harvest"}},{"id":"user","value":0.86,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/nordic-22rb-upper 7f994902ea3b (the user's own 22RB from above, the rail's teeth from end to end; 2026-10-03)","scaleRef":"the rail's slots, found by their walls' dark lines (0.42 px rms): the rail's own plane","method":"the charging handle's T's rear face, straight and square to the rail, 1.656 behind the first slot's centre (0.795). The side photos have the T's wing tip, 0.985 in off the centre plane, at -0.950 and -0.943 apparent, which is -0.87 with the lens allowed for. ± is the slot grid (0.012) and which wall a shadow favours (0.02)","via":"user"},"note":"The handle is home against the rail block. The two product photos' 1.24 isn't reproduced on the user's upper: 0.38 in further back, in photos whose anchor is 0.08 off at most; what stood there in Nordic's photos (a latch, a handle not home) isn't known."}],"adopt":{"from":"user","reason":"The user's own upper, read in the rail's plane from above, the side photos agreeing. The product photos' 1.239 and 1.236 agree with each other and not with the part in hand."}},"barrel_od":{"label":"Barrel OD (profile)","kind":"length","measurements":[{"id":"left","value":0.717,"unit":"in","pm":0.035,"source":{"type":"photo","photo":"references/nordic-22rb-upper 2b348f6a5149 (left side, NC22RB-UPPER-16-KIT_3_HR)","scaleRef":"rail model from 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%), anchored at takedown lug (1853.5,1074.5) = frame x 0","method":"median silhouette height 0.25–1.0 in behind the forward tip (a cylinder's diameter is unaffected by camera elevation)","via":"harvest"},"note":"Muzzle section OD. The thread protector and exposed barrel read the same diameter."},{"id":"right","value":0.711,"unit":"in","pm":0.076,"source":{"type":"photo","photo":"references/nordic-22rb-upper 24d592636074 (right side, Nordic NC22-16-Upper-V2)","scaleRef":"rail model from 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%), anchored at takedown lug (91.5,475.5) = frame x 0","method":"median silhouette height 0.25–1.0 in behind the forward tip (a cylinder's diameter is unaffected by camera elevation)","via":"harvest"}},{"id":"user-protector","value":0.736,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/nordic-22rb-upper 14dc07bfde38, d633f1bf49ff, 8c0c57f466e0, 9c62acf0f248, 7523d9cd1b94 (the user's own 22RB lying on a tile floor, each side, from 5 to 7 ft, zoomed; 2026-10-03)","scaleRef":"the rail's 49 slots, found at mid-depth of the teeth (a projective fit to their centres: 0.3 to 0.6 px rms, 106 to 120 px/in), and the two lug holes' see-through centres, all on the centre plane; a camera pose fitted to them. Checks: the lug holes read 6.383 apart directly (+0.13%), the handguard's M-LOK slits 1.573 to 1.582 apart (40 mm), the receiver's underside 0.24 to 0.25 above the pins (the deck's 0.254)","method":"the thread protector's diameter across its silhouette: 0.732, 0.735, 0.737, 0.737, 0.739. The polished barrel behind it mirrors the floor and reads thin (0.55): not read","via":"user"},"note":"The protector's (0.732 to 0.739 in five photos), which the barrel it sleeves is taken to equal: in the bare-muzzle photo (c0e654135597) the barrel is 1.5 times its 1/2 in thread across, 0.74 ± 0.02, which is the ± here. What the barrel measures under the handguard isn't seen."}],"adopt":{"from":"user-protector","reason":"The protector's diameter on the user's own upper in five photos (0.732 to 0.739); the barrel it sleeves is as large: in the bare-muzzle photo (c0e654135597) the barrel is 1.5 times its 1/2 in thread across (0.74 ± 0.02). The product photos' 0.717 and 0.711 are a glossy tube on white, which reads thin (CLAUDE.md)."},"note":"Not in the brief. Needed for the barrel mesh. M1b."},"handguard_length":{"label":"Handguard length","kind":"length","measurements":[{"id":"derived","value":13.538,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{.handguard_front_x} - {.handguard_rear_x}","via":"harvest"}}],"note":"Not published (the seed's gaps); Aawee's 13.5 in belongs to a handguard model that isn't confirmed for the 22RB. From the photos: the handguard front less the receiver/handguard seam. The user's tape on their own upper (4e2b3425b362, 2026-10-02: laid on the right side, the seam under it at 13.57, the handguard's front showing 0.02 to 0.12 behind its zero) reads 13.50, and isn't a measurement of this: the handguard's front is turned to a cone (handguard_nose_opening_d), so what shows beside the tape's end is the cone's surface or its rim, up to 0.44 in below the tape's plane, seen from a lens 16 in up and somewhere behind it. Over the middle of the photo that is 0.25 to 0.3 in of parallax, which is the whole difference; where the lens stood isn't known, so no figure is taken. A tape hooked on the front face would say (STATUS, photos to ask for)."},"handguard_nose_opening_d":{"label":"Handguard's mouth: the bore's diameter at its front rim, inside the chamfer","kind":"length","measurements":[{"id":"right-outline","value":0.721,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/nordic-22rb-upper 24d592636074 (right side, Nordic NC22-16-Upper-V2, 1200 px)","scaleRef":"rail model 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%, tilt +0.37°) along the rail and its local scale across it, anchored at the takedown lug (91.5, 475.5); the three nose figures are differences read within 0.4 in of one another in this one photo, so its frame's offset from the left photo's (0.245 in at the front) is out of them","method":"where the two slopes end on the barrel's silhouette: y 0.509 below and 1.23 above (profiles.side). The barrel there is 0.711 across in this photo (barrel_od's right reading), so the opening is the barrel's diameter and a clearance the photo doesn't resolve; ± is a pixel and a half","via":"harvest"}},{"id":"user-end","value":1.53,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/nordic-22rb-upper 2cd733a9d284, 0dad4e900d85 (the user's own 22RB, the muzzle end straight on, the rail at the bottom, a tape across above; 2026-10-03)","scaleRef":"the octagon's own width in the same view (handguard_width)","method":"the mouth as the end-on photos show it: an open tube, the M-LOK slots' light in seven rows running away down the bore round the barrel; at its rim a turned ring between r 0.765 and 0.797, the edge of a chamfer from the flats in to r 0.765","via":"user"},"note":"The right product photo's side outline had been read as a cone closing on the barrel to a 0.721 opening, 0.136 ahead of the flats' front and leaving them 0.172 behind it (handguard_nose_rim_ahead and handguard_nose_flat_behind, dropped with this reading): it is the open mouth seen from the side."}],"adopt":{"from":"user-end","reason":"The user's own upper, straight on: an open tube. The side photo's \"cone\" was the mouth's chamfer and the bore's far wall."},"note":"The handguard's front isn't square: it is turned to a cone that closes on the barrel. In the side view its silhouette slopes back above and below the barrel, from where it meets the barrel's to the flats. Three figures give the cone (this, handguard_nose_rim_ahead, handguard_nose_flat_behind), each from the right product photo's traced outline (profiles.side: (19.846, 0.088) the bottom flat's front end, (20.03, 0.269), (20.127, 0.48), (20.156, 0.509) on the barrel's underside; (20.151, 1.23) on its top, (19.962, 1.615) at the rail's neck). The user's own upper shows the same nose: from above, the front corners cut back in plan (d20d09340d49); lying on its side, a rounded front, as a cone through an octagon's flats is (4e2b3425b362). handguard_front_x is a point part-way up this cone (where the silhouette is half an inch taller than the barrel), which M5 to 2026-10-02 drew as a square front."},"handguard_rear_x":{"label":"Handguard rear end (the seam with the receiver's front), X","kind":"length","measurements":[{"id":"left","value":6.47,"unit":"in","pm":0.035,"source":{"type":"photo","photo":"references/nordic-22rb-upper 2b348f6a5149 (left side, NC22RB-UPPER-16-KIT_3_HR)","scaleRef":"rail model from 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%), anchored at takedown lug (1853.5,1074.5) = frame x 0","method":"the seam picked at x 1305 ± 1.5 px over rows 940–1040 on a 3× gridded crop, mapped through the rail model; ± is the pick (0.018) plus 3× rail rms and the anchor","via":"harvest"}},{"id":"right","value":6.382,"unit":"in","pm":0.054,"source":{"type":"photo","photo":"references/nordic-22rb-upper 24d592636074 (right side, Nordic NC22-16-Upper-V2)","scaleRef":"rail model from 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%), anchored at takedown lug (91.5,475.5) = frame x 0","method":"the seam picked at x 422.5 ± 1 px over rows 400–450 on a 9× gridded crop, mapped through the rail model; ± is the pick (0.02) plus 3× rail rms","via":"harvest"}},{"id":"left-midplane","value":6.494,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/nordic-22rb-upper 2b348f6a5149 (left side, NC22RB-UPPER-16-KIT_3_HR)","scaleRef":"rail model from 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%), anchored at takedown lug (1853.5,1074.5) = frame x 0; the lens from the same rail (its teeth's silhouettes are narrowest at px 1005 and widen 0.0069 in for each inch off it, across a rail 0.835 in wide)","method":"the left pick (6.47), carried from the receiver's near wall, where the seam is seen, to the rail's mid-plane, where the rail model's scale is. The wall stands half the receiver's width ({.width} / 2 = 0.801 in) nearer the lens, and the pick is 3.59 in off the lens's axis (px 1305 against 1005 at 83.6 px/in), toward the rear: a point that much nearer shows 3.59 × 0.801 / 0.835 × 0.0069 = 0.0238 in further from the axis than it is, so the seam is that much further forward. ± is the pick's (0.035) plus the correction's own doubt (the receiver's width ± 0.06, the widening read to about a tenth: 0.004)","via":"harvest"},"note":"The correction the 2026-10-02 rail-break work measured and left unapplied (STATUS, small issues: the receiver rail's last tooth drawn 0.05 in narrow). The right photo's pick needs the same kind of correction and has no lens reading to make it with."},{"id":"rail","value":6.597,"unit":"in","pm":0.036,"source":{"type":"derived","expr":"{.receiver_rail_front_x}","via":"user"},"note":"Where the receiver's rail ends: the two parts' rails break where the parts do (the left photo shows the last tooth's front face on the seam's line; from above, on the user's own upper, the seam runs into that face)."}],"adopt":{"from":"rail","reason":"The seam is where the rail breaks, and that is known best: a whole tooth's front face on the slot grid (receiver_rail_front_x). The left photo's own reading of the seam, carried to the rail's plane (6.494 ± 0.04), agrees; the right photo reads ~1.2% short along the upper. On the user's own upper the seam stands the same 0.06 in behind the pivot lug's front edge as in the left product photo (4e2b3425b362: 6 px at 104 px/in; 6 px at 84)."},"note":"A vertical seam just ahead of the pivot lug, plain in both rail-calibrated side photos; the handguard's clamp boss (two screws) hangs below just ahead of it (x 6.8–7.9). Not on the silhouette, so picked on gridded crops and mapped through each photo's rail model. The right photo reads short along the whole upper (its handguard front is 0.245 in short at x 20, ~1.2%), which predicts ~0.08 in here: the two agree once that's allowed for."},"rail_slot0_x":{"label":"X of the rearmost top-rail slot center","kind":"length","measurements":[{"id":"left","value":0.713,"unit":"in","pm":0.035,"source":{"type":"photo","photo":"references/nordic-22rb-upper 2b348f6a5149 (left side, NC22RB-UPPER-16-KIT_3_HR)","scaleRef":"rail model from 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%), anchored at takedown lug (1853.5,1074.5) = frame x 0","method":"silhouette slot_first_x along the rail model; ± is 3× rail rms plus edge and anchor error","via":"harvest"},"note":"Rearmost detected top-rail slot center; slot index 0 in the build's optic_slot/magnifier_slot."},{"id":"user","value":0.795,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/nordic-22rb-upper 14dc07bfde38, d633f1bf49ff, 8c0c57f466e0, 9c62acf0f248, 7523d9cd1b94 (the user's own 22RB lying on a tile floor, each side, from 5 to 7 ft, zoomed; 2026-10-03)","scaleRef":"the rail's 49 slots, found at mid-depth of the teeth (a projective fit to their centres: 0.3 to 0.6 px rms, 106 to 120 px/in), and the two lug holes' see-through centres, all on the centre plane; a camera pose fitted to them. Checks: the lug holes read 6.383 apart directly (+0.13%), the handguard's M-LOK slits 1.573 to 1.582 apart (40 mm), the receiver's underside 0.24 to 0.25 above the pins (the deck's 0.254)","method":"the rearmost slot's centre: 0.797 and 0.799 in the two photos taken square on, 0.790, 0.788 and 0.787 in the three taken from 9 in toward the lugs; ± is their spread and the anchor (.cache/photos/22rb, 2026-10-03)","via":"user"},"note":"The left product photo's 0.713 is anchored at its takedown lug alone, in a photo that reads the pins 1.25% short (pin_spacing's note): against its own pivot hole its seam stands 0.19 to 0.21 ahead, as here (0.225)."}],"adopt":{"from":"user","reason":"The user's own upper in five photos, framed by both lug holes and the rail itself. The product photo's grid sat 0.08 behind it: its anchor, not the part."},"note":"Needed to index optics by slot. M1b, from a rail-calibrated side photo."},"weight":{"label":"Weight, complete upper","kind":"mass","measurements":[{"id":"spec","value":60,"unit":"oz","stated":"Approximate Weight: 3 lbs., 12 oz.","source":{"type":"spec","publisher":"manufacturer","name":"Nordic Components 22RB page","url":"https://nordiccomp.com/categories/nc-22rb-upper/","retrieved":"2026-09-30","via":"harvest"},"note":"Nordic says approximate, and it is a round quarter pound. Whether the magazine it ships with counts was unclear until the user weighed their own (user-scale): it doesn't. A 2015 review weighed an older build at 4 lb 3 oz."},{"id":"user-scale","value":1718,"unit":"g","stated":"The Nordic upper is actually 1718 grams","source":{"type":"caliper","date":"2026-10-05","instrument":"the user's scale (not named), their own upper on it, as asked for on 2026-10-02 (\"the upper alone on it, no magazine\": docs/STATUS.md, the photo list's 7)","via":"user"},"note":"Their correction, the same hour, of the 1740 grams they gave first; what the 22 g between the two was isn't said. Taken as the upper as it ships and as their photos show it: the bolt and the charging handle in, the thread protector on, nothing mounted on its rail. No ± given: compared at half its last digit, a figure to the gram. 60.60 oz."}],"adopt":{"from":"user-scale","reason":"The user's own upper on a scale, against a figure its maker calls approximate: 0.60 oz (1.0%) over Nordic's 3 lb 12 oz, a tenth of an ounce more than a figure given to the ounce allows. It settles what Nordic's figure counts: not the magazine (with a 3.2 oz magazine in it, the upper alone would be 56.8 oz, 3.8 under the scale). Nordic's stays inside what the weight spans: the maker's figure for the product against one unit of it."}},"rail_last_slot_x":{"label":"Frontmost top-rail slot center, X","kind":"length","measurements":[{"id":"left","value":19.625,"unit":"in","pm":0.035,"source":{"type":"photo","photo":"references/nordic-22rb-upper 2b348f6a5149 (left side, NC22RB-UPPER-16-KIT_3_HR)","scaleRef":"rail model from 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%), anchored at takedown lug (1853.5,1074.5) = frame x 0","method":"silhouette slot_last_x along the rail model; ± is 3× rail rms plus edge and anchor error","via":"harvest"}},{"id":"user","value":19.693,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/nordic-22rb-upper 14dc07bfde38, d633f1bf49ff, 8c0c57f466e0, 9c62acf0f248, 7523d9cd1b94 (the user's own 22RB lying on a tile floor, each side, from 5 to 7 ft, zoomed; 2026-10-03)","scaleRef":"the rail's 49 slots, found at mid-depth of the teeth (a projective fit to their centres: 0.3 to 0.6 px rms, 106 to 120 px/in), and the two lug holes' see-through centres, all on the centre plane; a camera pose fitted to them. Checks: the lug holes read 6.383 apart directly (+0.13%), the handguard's M-LOK slits 1.573 to 1.582 apart (40 mm), the receiver's underside 0.24 to 0.25 above the pins (the deck's 0.254)","method":"the 49th slot's centre: 48 pitches ahead of the first (0.795), read at 19.700 and 19.702 in the two photos taken square on","via":"user"}}],"adopt":{"from":"user","reason":"The user's own upper; 48 pitches ahead of the first slot. The product photo's 19.625 sat behind it with its grid."}},"rail_rear_x":{"label":"Top rail's rear end (the rail head's rear face), X","kind":"length","measurements":[{"id":"right-photo","value":-0.552,"unit":"in","pm":0.029,"source":{"type":"photo","photo":"references/nordic-22rb-upper 24d592636074 (right side, Nordic NC22-16-Upper-V2, 1200 px)","scaleRef":"rail model 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%, tilt +0.37°) along the rail and its local scale across it (52.2 px/in at the anchor), anchored at the takedown lug (91.5, 475.5)","method":"x_min in y [2.03, 2.3] of the traced outline (tools/trace.py); the rail head's rear face: rows above the charging handle's top (2.00) and below the tooth tops (2.07)","via":"harvest"}},{"id":"user","value":0.57,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/nordic-22rb-upper b8e5873d5ebc (the user's own 22RB: the receiver's rear end from above, close, the handle home; 2026-10-05)","scaleRef":"the T's own width beside it in the rail's plane (charging_handle_t_width: 1318.4 px end to end, 669 px/in), which a tooth's top flat (437.7 px for the standard's 0.656: 667) and slot 0's front wall (1.755 in ahead of the T's rear face for the ledger's 1.758) agree with","method":"the rail from above: slot 0's rear wall at column 1599, the standard's head behind it at its full width for 80 px (columns 1519 to 1599), and behind that the rail at 0.64 in across with upright sides (columns 890 to 1519). The T's rear face is at column 560.8 on the centre line: (1519 - 560.8) / 667 less rear_behind_pin. ± is the corner's round (10 px) and the scale's 1%","via":"user"}}],"adopt":{"from":"user","reason":"They are two ends of two things. Seen from above on the user's own upper the standard's head, shoulders and all, stops 0.12 in behind slot 0; from there back the rail is a tongue of its top's width with a round nose (rail_tongue_*), which is what the product photo's silhouette has at -0.552. The app draws the standard's head from here."},"note":"With rail_front_x, where the app draws the rail head to MIL-STD-1913 (std.picatinny.*) over the traced body. The rail is solid from here to the first slot (rail_slot0_x). Until 2026-10-05 this was the rail's rearmost point in a side photo, and the head was drawn at its full width from there: behind this the rail is a tongue as wide as its top, over the charging handle (rail_tongue_width, rail_tongue_rear_x, rail_tongue_bottom_y), which the receiver's model carries."},"rail_front_x":{"label":"Top rail's front end (the last tooth's front face), X","kind":"length","measurements":[{"id":"left-photo","value":19.946,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/nordic-22rb-upper 2b348f6a5149 (left side, NC22RB-UPPER-16-KIT_3_HR, 2000 px)","scaleRef":"rail model 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%, tilt +0.15°) along the rail and its local scale across it (85.9 px/in at the anchor), anchored at the takedown lug (1853.5, 1074.5)","method":"x_max in y [2.03, 2.3] of the traced outline (tools/trace.py); the last tooth's front face: rows between the slot floors (2.00) and the tooth tops (2.09–2.11)","via":"harvest"}},{"id":"user","value":19.98,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/nordic-22rb-upper 14dc07bfde38, d633f1bf49ff, 8c0c57f466e0, 9c62acf0f248, 7523d9cd1b94 (the user's own 22RB lying on a tile floor, each side, from 5 to 7 ft, zoomed; 2026-10-03); and 7f994902ea3b (from above)","scaleRef":"the rail's 49 slots, found at mid-depth of the teeth (a projective fit to their centres: 0.3 to 0.6 px rms, 106 to 120 px/in), and the two lug holes' see-through centres, all on the centre plane; a camera pose fitted to them. Checks: the lug holes read 6.383 apart directly (+0.13%), the handguard's M-LOK slits 1.573 to 1.582 apart (40 mm), the receiver's underside 0.24 to 0.25 above the pins (the deck's 0.254)","method":"the last tooth's front face, the perspective of the rail's near edge taken off: 19.98 from the side; 19.95 from above, in the rail's own plane","via":"user"}}],"adopt":{"from":"user","reason":"The user's own upper, from the side and from above; the product photo's 19.946 ± 0.02 agrees."},"note":"The last slot (rail_last_slot_x 19.625) plus half a slot puts the last tooth at 19.728–19.946: 0.218 wide, against the standard's 0.188 (pitch less slot), within the ±. The right photo can't give it: there the lens looks along the slots and the far teeth fill them, so its outline is smooth from x ≈ 16.6."},"rail_slots":{"label":"Top-rail slots (continuous run seen in the side view)","kind":"count","measurements":[{"id":"left","value":49,"unit":"count","source":{"type":"photo","photo":"references/nordic-22rb-upper 2b348f6a5149 (left side, NC22RB-UPPER-16-KIT_3_HR)","scaleRef":"rail model from 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%), anchored at takedown lug (1853.5,1074.5) = frame x 0","method":"slot indices spanned by the rail fit (a rail end hidden by a part would be missed)","via":"harvest"}},{"id":"user-top","value":49,"unit":"count","source":{"type":"photo","photo":"references/nordic-22rb-upper d20d09340d49 (the user's own 22RB from above, rail up, a tape on the floor beside it; supplied in chat 2026-10-02)","scaleRef":"none needed (a count)","method":"every tooth marked on the rail from above and checked by eye: 49 teeth from the front one to the last before the solid block under the charging handle, a slot behind each: 49 slots. The user's suggestion (2026-10-02: \"count the rail teeth and see exactly how many lie to either side of that seam\")","via":"user"},"note":"Counted on the user's own upper; the product photo's rail fit had given the same."}],"adopt":{"from":"user-top","reason":"Counted tooth by tooth on the user's own upper; the left product photo's rail fit spans the same 49."}},"receiver_rail_slots":{"label":"Top-rail slots on the receiver (behind the seam)","kind":"count","measurements":[{"id":"user-top","value":15,"unit":"count","source":{"type":"photo","photo":"references/nordic-22rb-upper d20d09340d49 (the user's own 22RB from above, rail up, a tape on the floor beside it; supplied in chat 2026-10-02)","scaleRef":"none needed (a count)","method":"the seam found where the handguard's body ends and the receiver's narrower one begins (its line shows on the body beside the rail with the contrast raised), and the teeth counted either side of it: 34 ahead, 15 behind and the block","via":"user"}}],"note":"Which side of the seam each slot is on, counted on the user's own upper from above: the handguard's rail has 34 teeth and 34 slots and ends at the seam with a slot; the receiver's begins there with a whole tooth and has 15 teeth, 15 slots, then the solid block under the charging handle. So of the run's 49 slots (rail_slots), indexed from the rear, 0 to 14 are the receiver's and 15 to 48 the handguard's: what the positions give (receiver_rail_front_x between slots 14 and 15), now counted."},"receiver_rail_last_tooth_deficit":{"label":"Receiver rail's tooth at the seam, how much narrower than its neighbours","kind":"length","measurements":[{"id":"user-top-b","value":0.005,"unit":"in","pm":0.009,"source":{"type":"photo","photo":"references/nordic-22rb-upper d20d09340d49 (the user's own 22RB from above, rail up, a tape on the floor beside it; supplied in chat 2026-10-02)","scaleRef":"the rail's own pitch beside it (30.8 px a pitch there, 78 px/in)","method":"tooth tops along the rail's middle (the lighter flats; edges at the level midway between a flat and the slots beside it): the receiver's first tooth 13.3 px against 13.2 and 14.2 for the teeth either side of it (the widths rise along the photo with its scale: 13.7 expected between them), so 0.4 px narrow; ± is half a pixel at each edge","via":"user"}},{"id":"user-top-a","value":0.004,"unit":"in","pm":0.009,"source":{"type":"photo","photo":"references/nordic-22rb-upper f516653ab36f (the user's own 22RB from above, a second frame; supplied in chat 2026-10-02)","scaleRef":"the rail's own pitch beside it (30.4 px a pitch there, 77 px/in)","method":"as user-top-b, in the second frame: 13.3 px against 13.4 and 13.8 either side (13.6 expected), 0.3 px narrow","via":"user"}}],"adopt":{"from":"user-top-b","reason":"The frame in which every tooth was found and counted; the other agrees."},"note":"Whether the receiver's rail ends at the seam with a whole tooth. The side photos had its front face at the seam within a pixel, but the seam's own position (read on a wall, mapped through a rail model) left that tooth drawn 0.05 and then 0.03 in narrower than the rest. From above, on the rail's top, the tooth is measured against its neighbours in the same plane: it is whole."},"handguard_front_x":{"label":"Handguard's front end (its front-most rim), X","kind":"length","measurements":[{"id":"left","value":20.263,"unit":"in","pm":0.035,"source":{"type":"photo","photo":"references/nordic-22rb-upper 2b348f6a5149 (left side, NC22RB-UPPER-16-KIT_3_HR)","scaleRef":"rail model from 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%), anchored at takedown lug (1853.5,1074.5) = frame x 0","method":"forward-most x where the silhouette height exceeds the front plateau (0.717 in) by 0.5 in","via":"harvest"},"note":"Handguard front face: where the silhouette steps up from the barrel section."},{"id":"right","value":20.018,"unit":"in","pm":0.076,"source":{"type":"photo","photo":"references/nordic-22rb-upper 24d592636074 (right side, Nordic NC22-16-Upper-V2)","scaleRef":"rail model from 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%), anchored at takedown lug (91.5,475.5) = frame x 0","method":"forward-most x where the silhouette height exceeds the front plateau (0.711 in) by 0.5 in","via":"harvest"}},{"id":"user-tape","value":20.135,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/nordic-22rb-upper 07c956984adb, f437f1401e77 (the user's own 22RB, a tape hooked on the handguard's nose and laid back along its side flat; 2026-10-03)","scaleRef":"the tape itself, read where it lies: its ticks located one by one beside the seam","method":"the seam on the side flat reads 13.550 and 13.564 on the tape; the hook's outer face stands 0.014 and 0.022 beyond the tape's zero, so the handguard bears on the hook's inner face, whose tab is taken as 0.04 thick (not measured): 13.535 from the seam to the front-most rim, and the seam is at 6.60 (handguard_rear_x). Corroborated across planes, not used: the near side flat's front edge reads 20.278 in the far photos (0.8 in nearer the lens: 20.13 to 20.17 true), the body's front 20.12 from above, the floor tape 1.46 ± 0.06 from the front to the protector's face. ± is the hook's tab and whether it touched (0.03) and the seam (0.015)","via":"user"},"note":"The 2026-10-02 tape photo's 13.50 to 13.57, set aside then as parallax, was right."}],"adopt":{"from":"user-tape","reason":"A tape lying on the part, read in its own plane, twice. The left product photo's 20.263 is the near flat's edge as its lens saw it (the user's far photos read the same 20.28 apparent); the 13.88 to a rim that the cone was thought to carry came from the right photo's outline."}},"receiver_rear_x":{"label":"Receiver rear face (below the charging handle), X","kind":"length","measurements":[{"id":"left","value":-0.983,"unit":"in","pm":0.035,"source":{"type":"photo","photo":"references/nordic-22rb-upper 2b348f6a5149 (left side, NC22RB-UPPER-16-KIT_3_HR)","scaleRef":"rail model from 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%), anchored at takedown lug (1853.5,1074.5) = frame x 0","method":"silhouette x_min in y [0.35, 0.7] (rows at the anchor scale) along the rail model; ± is 3× rail rms plus edge and anchor error","via":"harvest"},"note":"Receiver rear face, below the charging handle and above the takedown lug (the band sits between the receiver bottom and the bore axis)."},{"id":"right","value":-0.91,"unit":"in","pm":0.076,"source":{"type":"photo","photo":"references/nordic-22rb-upper 24d592636074 (right side, Nordic NC22-16-Upper-V2)","scaleRef":"rail model from 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%), anchored at takedown lug (91.5,475.5) = frame x 0","method":"silhouette x_min in y [0.35, 0.7] (rows at the anchor scale) along the rail model; ± is 3× rail rms plus edge and anchor error","via":"harvest"}},{"id":"user","value":-0.84,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/nordic-22rb-upper 14dc07bfde38, d633f1bf49ff, 8c0c57f466e0, 9c62acf0f248, 7523d9cd1b94 (the user's own 22RB lying on a tile floor, each side, from 5 to 7 ft, zoomed; 2026-10-03)","scaleRef":"the rail's 49 slots, found at mid-depth of the teeth (a projective fit to their centres: 0.3 to 0.6 px rms, 106 to 120 px/in), and the two lug holes' see-through centres, all on the centre plane; a camera pose fitted to them. Checks: the lug holes read 6.383 apart directly (+0.13%), the handguard's M-LOK slits 1.573 to 1.582 apart (40 mm), the receiver's underside 0.24 to 0.25 above the pins (the deck's 0.254)","method":"the bolt assembly's steel rear end, on the bore's axis: -0.833 and -0.854 in the two photos taken square on. The receiver's own rear face shows at -0.658 and -0.663 (its near edge: about -0.61, the standard's -0.621)","via":"user"}}],"adopt":{"from":"user","reason":"The user's own upper, the steel end on the centre plane. The product photos' -0.983 and -0.91 share the frame that put the rear 0.38 in back."},"note":"Cross-part question: this is 0.6 in behind the front of the Workhorse's buffer tower (bad-workhorse-lower.tower_front_x, −0.31). Both readings are corroborated by two photos each. Likely explanation: the tower's side walls run forward of the threaded ring (its internal threads are visible between them in both side photos), and the upper's rear nests between the walls. To confirm: a pin-calibrated side view of an assembled rifle. M6: the Army's drawing puts the threaded ring's front face 0.628 behind the takedown pin (std.ar15.buffer_tower_front_x) and a standard upper's rear just ahead of it, so this face, 0.35 further back in a band below the bore, stands inside the ring's 1.19 in bore: the rear of the .22 bolt assembly's housing, not the receiver's rear face."},"handguard_od":{"label":"Handguard size across the side flats (listed \"outer diameter\")","kind":"length","measurements":[{"id":"aawee-xl","value":40.7,"unit":"mm","stated":"Outer diameter 40.7mm, inner diameter 35.6mm.","source":{"type":"spec","publisher":"retailer","name":"Aawee, NCT3 15.3 in handguard (text relayed by the user; the page renders by script)","url":"https://www.aawee.fi/en/parts-and-accessories/nc-ar-15-nct3-lightweight-handguard-15-3-m-lok-freefloat-freefloat-lightweight-39cm-nc-xl/p/NCT3-HG-XL-CO-BLK/","retrieved":"2026-09-30","via":"user"}},{"id":"aawee-xxl","value":40.7,"unit":"mm","stated":"Outer diameter 40.7mm, inner diameter 35.6mm","source":{"type":"spec","publisher":"retailer","name":"Aawee, NCT3 17.2 in handguard","url":"https://www.aawee.fi/en/parts-and-accessories/nc-ar-15-nct3-handguard-17-2-m-lok-freefloat-freefloat-lightweight-43-6cm-nc-xxl/p/NCT3-HG-XXL-CO-BLK/","retrieved":"2026-09-30","via":"harvest"}}],"adopt":{"from":"aawee-xl","reason":"The listing that states the NC 22LR compatibility. Both lengths list the same profile."},"note":"Nordic's NCT3, which Aawee sells as matching the handguard on Nordic's M-LOK 22 uppers: 'Compatible with NC 22lr rifle upper receiver with M-LOK handguard like the original handguard.' Nordic's own photo of the 22RB's muzzle end shows the same octagon and slot layout. The listings don't say corners or flats. Read as across the side flats (M5): Aawee's straight end-on photo of the NCT3 (references/nordic-22rb-upper 5dc13057dabd) is 0.810 as wide across its side flats as it is tall from the bottom flat to the rail top, so with the 22RB's side-view height (2.04) it's 1.65 wide; 40.7 mm across the flats gives 1.60, across the corners only 1.48 (and then a section 1.83 tall, not 2.04). The rail runs straight into the upper diagonal faces: the octagon has no top flat."},"handguard_id":{"label":"Handguard bore (inside diameter)","kind":"length","measurements":[{"id":"aawee-xl","value":35.6,"unit":"mm","stated":"Outer diameter 40.7mm, inner diameter 35.6mm.","source":{"type":"spec","publisher":"retailer","name":"Aawee, NCT3 15.3 in handguard (text relayed by the user; the page renders by script)","url":"https://www.aawee.fi/en/parts-and-accessories/nc-ar-15-nct3-lightweight-handguard-15-3-m-lok-freefloat-freefloat-lightweight-39cm-nc-xl/p/NCT3-HG-XL-CO-BLK/","retrieved":"2026-09-30","via":"user"}},{"id":"aawee-xxl","value":35.6,"unit":"mm","stated":"Outer diameter 40.7mm, inner diameter 35.6mm","source":{"type":"spec","publisher":"retailer","name":"Aawee, NCT3 17.2 in handguard","url":"https://www.aawee.fi/en/parts-and-accessories/nc-ar-15-nct3-handguard-17-2-m-lok-freefloat-freefloat-lightweight-43-6cm-nc-xxl/p/NCT3-HG-XXL-CO-BLK/","retrieved":"2026-09-30","via":"harvest"}}],"adopt":{"from":"aawee-xl","reason":"Both listings agree; the same figure as the outer diameter's source (handguard_od)."},"note":"The NCT3's end view shows a round bore inside the octagon, with the slots opening into it on every face but the top."},"mlok_slot_front_x":{"label":"Handguard's foremost M-LOK slot, centre X","kind":"length","measurements":[{"id":"left","value":18.874,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/nordic-22rb-upper 2b348f6a5149 (left side, NC22RB-UPPER-16-KIT_3_HR)","scaleRef":"rail model from 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%), anchored at takedown lug (1853.5,1074.5) = frame x 0","method":"the barrel seen through the slots in the upper (y 978 px) and side (1035 px) rows: the bright runs' centres of the three full-length slots in each row, stepped forward by the 40 mm pitch (mlok.slot_pitch) to the first slot: six estimates 18.864–18.883; the runs' centres fall 1.58, 1.58, 1.54, 1.57, 1.57 in apart (1.575 is the pitch)","via":"harvest"}},{"id":"user","value":18.976,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/nordic-22rb-upper 14dc07bfde38 (the user's own 22RB, left side, square on from 5 to 7 ft; 2026-10-03)","scaleRef":"the rail's 49 slots, found at mid-depth of the teeth (a projective fit to their centres: 0.3 to 0.6 px rms, 106 to 120 px/in), and the two lug holes' see-through centres, all on the centre plane; a camera pose fitted to them. Checks: the lug holes read 6.383 apart directly (+0.13%), the handguard's M-LOK slits 1.573 to 1.582 apart (40 mm), the receiver's underside 0.24 to 0.25 above the pins (the deck's 0.254)","method":"the foremost slot's centre in the lower diagonal row, seen through to the far wall (centre plane): the six full slots at 11.092, 12.670, 14.243, 15.817, 17.393, 18.976 (pitch 1.577 against 40 mm's 1.5748)","via":"user"}}],"adopt":{"from":"user","reason":"The user's own upper, through the pose that the pins and the rail fix; the product photo's 18.874 sat 0.10 behind, as its rail grid did."}},"mlok_rear_slot_length":{"label":"M-LOK: the rearmost slot of each row, its length","kind":"length","measurements":[{"id":"user","value":0.93,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/nordic-22rb-upper 14dc07bfde38 (the user's own 22RB, left side, square on; 2026-10-03); bdb43e3235ed (from below)","scaleRef":"the rail's 49 slots and the two lug holes' see-through centres, all on the centre plane, in one fitted camera pose (rail_slot0_x#user)","method":"the rearmost opening of the lower diagonal row seen through to the far wall: 9.23 to 10.15 (0.92, about 0.94 with its ends' rounding), its front end on the 40 mm grid and its rear 0.31 short of a full slot's; the bottom face's row has the same short slot (strip px 1151 to 1254 against the diagonal's 1153 to 1253). Full slots read 1.22 to 1.24 where the lens looks straight through","via":"user"}}],"note":"Every row's rearmost slot is the short one: seven slots a face, six of them the standard's 32 mm."},"mlok_slots_per_face":{"label":"Handguard M-LOK slots per face","kind":"count","measurements":[{"id":"left","value":7,"unit":"count","source":{"type":"photo","photo":"references/nordic-22rb-upper 2b348f6a5149 (left side, NC22RB-UPPER-16-KIT_3_HR)","scaleRef":"none (a count)","method":"counted in the upper and side rows; the lower row's foreshortened slits agree","via":"harvest"}}],"note":"Through-slots; behind them each row ends in a blind panel the length of a slot, not drawn."},"receiver_block_width":{"label":"Receiver section: the block under the rail, width","kind":"length","measurements":[{"id":"rear","value":0.605,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/nordic-22rb-upper 11e268939f9f (Nordic, looking forward down the receiver from the rear)","scaleRef":"the section's full width, 272 px = the receiver's 1.38 in (width): 197 px/in across","method":"the block's vertical sides at the rear face (px 521 and 640, 119 px), above where the chamfers start","via":"harvest"}}],"note":"Nordic's receiver is an extrusion (constant section): this rear face is its section, the rail machined off behind the rail's rear end."},"receiver_chamfer_top_y":{"label":"Receiver section: the upper chamfers' top edge, Y","kind":"length","measurements":[{"id":"16in","value":1.645,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/nordic-22rb-upper 24d592636074 (right side, Nordic NC22-16-Upper-V2)","scaleRef":"rail model from 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%), anchored at takedown lug (91.5,475.5) = frame x 0; 52.0 px/in at the receiver; reads ~1.2% short along the upper","method":"a horizontal edge on the receiver's side, the same row at u 180, 230 and 400","via":"harvest"}},{"id":"18in","value":1.652,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/nordic-22rb-upper a379557904df (Nordic, 18 in 22RB upper, true right side, 4096 px)","scaleRef":"pin frame from the upper's lug holes picked on 8x crops: takedown (472, 1335.3), pivot (1362.4, 1334.4) = (0, 0), (6.375, 0): 139.7 px/in, the lugs in the receiver's plane","method":"horizontal edges at u 700 and 850 (1.649, 1.656)","via":"harvest"}}],"adopt":{"from":"16in","reason":"Both photos agree to 0.007."}},"receiver_chamfer_bottom_y":{"label":"Receiver section: the upper chamfers' bottom edge (the sides' top), Y","kind":"length","measurements":[{"id":"16in","value":1.177,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/nordic-22rb-upper 24d592636074 (right side, Nordic NC22-16-Upper-V2)","scaleRef":"rail model from 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%), anchored at takedown lug (91.5,475.5) = frame x 0; 52.0 px/in at the receiver; reads ~1.2% short along the upper","method":"horizontal edges at u 180, 230, 400 (1.164, 1.183, 1.183)","via":"harvest"}},{"id":"18in","value":1.158,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/nordic-22rb-upper a379557904df (Nordic, 18 in 22RB upper, true right side, 4096 px)","scaleRef":"pin frame from the upper's lug holes picked on 8x crops: takedown (472, 1335.3), pivot (1362.4, 1334.4) = (0, 0), (6.375, 0): 139.7 px/in, the lugs in the receiver's plane","method":"horizontal edges at u 700 and 850 (1.169, 1.147)","via":"harvest"}}],"adopt":{"from":"16in","reason":"Both photos agree within 0.02."}},"receiver_lower_corner_y":{"label":"Receiver section: the lower corners' top edge, Y","kind":"length","measurements":[{"id":"16in","value":0.631,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/nordic-22rb-upper 24d592636074 (right side, Nordic NC22-16-Upper-V2)","scaleRef":"rail model from 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%), anchored at takedown lug (91.5,475.5) = frame x 0; 52.0 px/in at the receiver; reads ~1.2% short along the upper","method":"horizontal edges at u 180, 230, 400 (0.625, 0.625, 0.644)","via":"harvest"}},{"id":"18in","value":0.615,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/nordic-22rb-upper a379557904df (Nordic, 18 in 22RB upper, true right side, 4096 px)","scaleRef":"pin frame from the upper's lug holes picked on 8x crops: takedown (472, 1335.3), pivot (1362.4, 1334.4) = (0, 0), (6.375, 0): 139.7 px/in, the lugs in the receiver's plane","method":"horizontal edges at u 700 and 850 (0.618, 0.611)","via":"harvest"}}],"adopt":{"from":"16in","reason":"Both photos agree within 0.02."}},"receiver_lower_corner_w":{"label":"Receiver section: the lower corners' width (inward at the bottom)","kind":"length","measurements":[{"id":"rear","value":0.134,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/nordic-22rb-upper 11e268939f9f (Nordic, looking forward down the receiver from the rear)","scaleRef":"the section's full width, 272 px = the receiver's 1.38 in (width): 197 px/in across","method":"the outline's width row by row at the rear face: 272 px down to 219 px at its last row above the lug (26.5 px a side); a lower bound: the curve may run further in under the lug","via":"harvest"}}]},"receiver_rear_chamfer_w":{"label":"Receiver: the rear lower chamfers' width (inward at the bottom)","kind":"length","measurements":[{"id":"user-rear","value":0.23,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/nordic-22rb-upper f07b87dfab90 (the user's own 22RB, the rear end straight on; 2026-10-03)","scaleRef":"the receiver's own width across its side flats in the same view (712.5 px = 1.31 in: width; 544 px/in)","method":"the outline's edge column by column (luminance 70): from the underside's edge to the side flat it is a straight line on both sides, 125 px across (0.23) over 195 px of height (0.36), the underside between them 463 px (0.85) and the side flats 290 px (0.53). A flat chamfer, not a round. ± is 5 px at each end of the line; the rear end's outline is spread over the 0.35 in of depth its rounded lower rear corner takes, under 3% of scale from where the lens stood","via":"user"},"note":"From below, straight down from 5 to 7 ft (bdb43e3235ed), the same chamfers show as a dark band 21 to 23 px wide inside each edge of a body 140.5 px across: 0.20 to 0.21."}],"note":"The user's own upper's lower corners are cut to flat chamfers over its rear half, from its rear end to a round run-out ahead of the takedown pin (receiver_rear_chamfer_front_x); ahead of that they are the section's own (receiver_lower_corner_w). Their upper edge is the corners' (receiver_lower_corner_y: 0.631; 0.61 in the end view below, 0.65 on the user's side photo). Until 2026-10-05 the model drew the section's rounded corner, 0.134 across, the whole way (the model review)."},"receiver_rear_chamfer_front_x":{"label":"Receiver: the front end of the rear lower chamfers (where their run-out reaches the underside), X","kind":"length","measurements":[{"id":"user-side","value":3,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/nordic-22rb-upper d633f1bf49ff (the user's own 22RB lying on its left side, its right side square on from 5 to 7 ft; 2026-10-03)","scaleRef":"the two lug holes' see-through centres (107.4 px/in: the frame the side outline was traced in); the chamfer is on the near side, 0.66 in nearer the lens than they are, and it is read 3 in from the pin","method":"luminance across the lower edge at stations along the receiver: the chamfer is a dark face (13 to 20) under the side flat (47 to 55), its upper edge 0.65 above the pin line from 0.6 to 2.7 in ahead of the pin, 0.635 at 2.8, about 0.50 at 2.9 and gone at 3.0, where the face under the flat is the section's own corner (41 to 49). A quarter round from 2.74 to 2.96 passes through all three, as the lens saw them: the near side reads toward the rear from where it stood, over the upper's middle (0.04 to 0.05 in here, by the 0.08 the charging handle's wing tip reads out in the same photo, 11 in from the lens's axis), so its end is 3.0. ± is the 0.1 in between stations, halved, and that correction's 0.02","via":"user"}},{"id":"user-below","value":2.95,"unit":"in","pm":0.2,"source":{"type":"photo","photo":"references/nordic-22rb-upper bdb43e3235ed (the user's own 22RB from below, straight down from 5 to 7 ft; 2026-10-03)","scaleRef":"the receiver's own width in the same view (140.5 px = 1.31 in: 107.3 px/in), from the takedown lug's middle (photo x 2437 ± 6)","method":"the dark band inside each edge is there at photo x 2140 and behind, and gone at 2100 and ahead, on both sides: its end at 2120 ± 20","via":"user"}}],"adopt":{"from":"user-side","reason":"Read square on in the frame the outline was traced in, at stations 0.1 in apart; from below it ends at the same place within that view's ±, and the close photo of the right side (e421a9af0aa7) shows the same run-out."}},"receiver_rear_chamfer_runout":{"label":"Receiver: the length of the rear lower chamfers' run-out (from their full height to the underside)","kind":"length","measurements":[{"id":"user-side","value":0.22,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/nordic-22rb-upper d633f1bf49ff (the user's own 22RB lying on its left side, its right side square on from 5 to 7 ft; 2026-10-03)","scaleRef":"the two lug holes' see-through centres (107.4 px/in: the frame the side outline was traced in)","method":"the chamfer's upper edge is at its full height 2.7 in ahead of the pin, 0.015 down at 2.8, about 0.15 down at 2.9 and at the underside by 3.0: a quarter round 0.22 long (2.74 to 2.96 as the lens saw it; receiver_rear_chamfer_front_x has its end with the lens allowed for). The close photo of the right side (e421a9af0aa7) shows its shape: level where it leaves the upper edge, square to the underside where it ends. ± is half the stations' spacing at each end","via":"user"}}]},"receiver_lug_width":{"label":"Receiver: the takedown and pivot lugs' width","kind":"length","measurements":[{"id":"rear","value":0.447,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/nordic-22rb-upper 11e268939f9f (Nordic, looking forward down the receiver from the rear)","scaleRef":"the section's full width, 272 px = the receiver's 1.38 in (width): 197 px/in across","method":"the takedown lug below the rear face, 88 px (px 532 to 620)","via":"harvest"}},{"id":"user-rear","value":0.49,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/nordic-22rb-upper f07b87dfab90 (the user's own 22RB, the rear end straight on; 2026-10-03)","scaleRef":"the receiver's own width across its side flats in the same view (714.8 px = 1.31 in: width), the lug 0.4 in further from the lens allowed for","method":"the takedown lug across, rows 833.4 to 1097.4 (264.0 px = 0.484 at the receiver's scale)","via":"user"}}],"adopt":{"from":"user-rear","reason":"The user's own upper, straight on; the earlier rear view's 0.447 ± 0.02 is a little under it. It fits the lower's lug slot (.500)."},"note":"Inside the lower's lug slot, .500 REF (TDP 8448608)."},"receiver_bore_d":{"label":"Receiver bore (the bolt's channel), diameter","kind":"length","measurements":[{"id":"rear","value":0.851,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/nordic-22rb-upper 11e268939f9f (Nordic, looking forward down the receiver from the rear)","scaleRef":"the section's full width, 272 px = the receiver's 1.38 in (width): 197 px/in across","method":"the bore's widest row at the rear face (167.5 px)","via":"harvest"}}],"note":"Drawn about the bore axis (bore_axis_above_pin). The ejection port opens into it."},"ejection_port_rear_x":{"label":"Ejection port opening, rear edge, X","kind":"length","measurements":[{"id":"18in","value":3.565,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/nordic-22rb-upper a379557904df (Nordic, 18 in 22RB upper, true right side, 4096 px)","scaleRef":"pin frame from the upper's lug holes picked on 8x crops: takedown (472, 1335.3), pivot (1362.4, 1334.4) = (0, 0), (6.375, 0): 139.7 px/in, the lugs in the receiver's plane","method":"the opening's rear end on a 4x crop (px 970)","via":"harvest"}},{"id":"16in","value":3.516,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/nordic-22rb-upper 24d592636074 (right side, Nordic NC22-16-Upper-V2)","scaleRef":"rail model from 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%), anchored at takedown lug (91.5,475.5) = frame x 0; 52.0 px/in at the receiver; reads ~1.2% short along the upper","method":"the opening's rear end on a 3x crop (px 275)","via":"harvest"}}],"adopt":{"from":"18in","reason":"Twice the resolution and a pin frame in the receiver's plane; the 16 in photo agrees (its ~1.2% short bias allowed for)."}},"ejection_port_front_x":{"label":"Ejection port opening, front edge, X","kind":"length","measurements":[{"id":"18in","value":5.283,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/nordic-22rb-upper a379557904df (Nordic, 18 in 22RB upper, true right side, 4096 px)","scaleRef":"pin frame from the upper's lug holes picked on 8x crops: takedown (472, 1335.3), pivot (1362.4, 1334.4) = (0, 0), (6.375, 0): 139.7 px/in, the lugs in the receiver's plane","method":"the opening's front end on a 4x crop (px 1210)","via":"harvest"}},{"id":"16in","value":5.193,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/nordic-22rb-upper 24d592636074 (right side, Nordic NC22-16-Upper-V2)","scaleRef":"rail model from 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%), anchored at takedown lug (91.5,475.5) = frame x 0; 52.0 px/in at the receiver; reads ~1.2% short along the upper","method":"the opening's front end on a 3x crop (px 362); +1.2% for the photo's bias is 5.255","via":"harvest"}}],"adopt":{"from":"18in","reason":"Twice the resolution and a pin frame in the receiver's plane; the 16 in photo agrees (its ~1.2% short bias allowed for)."}},"ejection_port_bottom_y":{"label":"Ejection port opening, bottom edge, Y","kind":"length","measurements":[{"id":"18in","value":0.833,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/nordic-22rb-upper a379557904df (Nordic, 18 in 22RB upper, true right side, 4096 px)","scaleRef":"pin frame from the upper's lug holes picked on 8x crops: takedown (472, 1335.3), pivot (1362.4, 1334.4) = (0, 0), (6.375, 0): 139.7 px/in, the lugs in the receiver's plane","method":"the opening's bottom on a 4x crop (py 1219)","via":"harvest"}},{"id":"16in","value":0.837,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/nordic-22rb-upper 24d592636074 (right side, Nordic NC22-16-Upper-V2)","scaleRef":"rail model from 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%), anchored at takedown lug (91.5,475.5) = frame x 0; 52.0 px/in at the receiver; reads ~1.2% short along the upper","method":"on a 3x crop (py 432)","via":"harvest"}}],"adopt":{"from":"18in","reason":"Twice the resolution and a pin frame in the receiver's plane; the 16 in photo agrees (its ~1.2% short bias allowed for)."}},"ejection_port_top_y":{"label":"Ejection port opening, top edge, Y","kind":"length","measurements":[{"id":"18in","value":1.309,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/nordic-22rb-upper a379557904df (Nordic, 18 in 22RB upper, true right side, 4096 px)","scaleRef":"pin frame from the upper's lug holes picked on 8x crops: takedown (472, 1335.3), pivot (1362.4, 1334.4) = (0, 0), (6.375, 0): 139.7 px/in, the lugs in the receiver's plane","method":"the opening's top on a 4x crop (py 1152.5): the bolt shows from 1.27 down","via":"harvest"}},{"id":"16in","value":1.376,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/nordic-22rb-upper 24d592636074 (right side, Nordic NC22-16-Upper-V2)","scaleRef":"rail model from 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%), anchored at takedown lug (91.5,475.5) = frame x 0; 52.0 px/in at the receiver; reads ~1.2% short along the upper","method":"on a 3x crop (py 404)","via":"harvest"}}],"adopt":{"from":"18in","reason":"Twice the resolution and a pin frame in the receiver's plane; the 16 in photo agrees (its ~1.2% short bias allowed for)."}},"ejection_port_corner_r":{"label":"Ejection port opening, corner radius","kind":"length","measurements":[{"id":"18in","value":0.063,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/nordic-22rb-upper a379557904df (Nordic, 18 in 22RB upper, true right side, 4096 px)","scaleRef":"pin frame from the upper's lug holes picked on 8x crops: takedown (472, 1335.3), pivot (1362.4, 1334.4) = (0, 0), (6.375, 0): 139.7 px/in, the lugs in the receiver's plane","method":"the opening's corner arcs on a 4x crop (~9 px)","via":"harvest"}}]},"ejection_port_pocket_rear_x":{"label":"Ejection port pocket (the milled recess around the opening), rear edge, X","kind":"length","measurements":[{"id":"18in","value":3.529,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/nordic-22rb-upper a379557904df (Nordic, 18 in 22RB upper, true right side, 4096 px)","scaleRef":"pin frame from the upper's lug holes picked on 8x crops: takedown (472, 1335.3), pivot (1362.4, 1334.4) = (0, 0), (6.375, 0): 139.7 px/in, the lugs in the receiver's plane","method":"the recess's rear end on a 4x crop (px 965)","via":"harvest"}},{"id":"16in","value":3.421,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/nordic-22rb-upper 24d592636074 (right side, Nordic NC22-16-Upper-V2)","scaleRef":"rail model from 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%), anchored at takedown lug (91.5,475.5) = frame x 0; 52.0 px/in at the receiver; reads ~1.2% short along the upper","method":"on a 3x crop (px 270)","via":"harvest"}}],"adopt":{"from":"18in","reason":"Twice the resolution and a pin frame in the receiver's plane; the 16 in photo agrees (its ~1.2% short bias allowed for)."}},"ejection_port_pocket_front_x":{"label":"Ejection port pocket, front edge, X","kind":"length","measurements":[{"id":"18in","value":5.326,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/nordic-22rb-upper a379557904df (Nordic, 18 in 22RB upper, true right side, 4096 px)","scaleRef":"pin frame from the upper's lug holes picked on 8x crops: takedown (472, 1335.3), pivot (1362.4, 1334.4) = (0, 0), (6.375, 0): 139.7 px/in, the lugs in the receiver's plane","method":"the recess's front end on a 4x crop (px 1216)","via":"harvest"}},{"id":"16in","value":5.271,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/nordic-22rb-upper 24d592636074 (right side, Nordic NC22-16-Upper-V2)","scaleRef":"rail model from 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%), anchored at takedown lug (91.5,475.5) = frame x 0; 52.0 px/in at the receiver; reads ~1.2% short along the upper","method":"on a 3x crop (px 366); +1.2% for the photo's bias is 5.334","via":"harvest"}}],"adopt":{"from":"18in","reason":"Twice the resolution and a pin frame in the receiver's plane; the 16 in photo agrees (its ~1.2% short bias allowed for)."}},"ejection_port_pocket_bottom_y":{"label":"Ejection port pocket, bottom edge, Y","kind":"length","measurements":[{"id":"18in","value":0.811,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/nordic-22rb-upper a379557904df (Nordic, 18 in 22RB upper, true right side, 4096 px)","scaleRef":"pin frame from the upper's lug holes picked on 8x crops: takedown (472, 1335.3), pivot (1362.4, 1334.4) = (0, 0), (6.375, 0): 139.7 px/in, the lugs in the receiver's plane","method":"on a 4x crop (py 1222)","via":"harvest"}},{"id":"16in","value":0.798,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/nordic-22rb-upper 24d592636074 (right side, Nordic NC22-16-Upper-V2)","scaleRef":"rail model from 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%), anchored at takedown lug (91.5,475.5) = frame x 0; 52.0 px/in at the receiver; reads ~1.2% short along the upper","method":"on a 3x crop (py 434)","via":"harvest"}}],"adopt":{"from":"18in","reason":"Twice the resolution and a pin frame in the receiver's plane; the 16 in photo agrees (its ~1.2% short bias allowed for)."}},"ejection_port_pocket_top_y":{"label":"Ejection port pocket, top edge, Y (where it runs out on the upper chamfer)","kind":"length","measurements":[{"id":"18in","value":1.452,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/nordic-22rb-upper a379557904df (Nordic, 18 in 22RB upper, true right side, 4096 px)","scaleRef":"pin frame from the upper's lug holes picked on 8x crops: takedown (472, 1335.3), pivot (1362.4, 1334.4) = (0, 0), (6.375, 0): 139.7 px/in, the lugs in the receiver's plane","method":"on a 4x crop (py 1132.5)","via":"harvest"}},{"id":"16in","value":1.414,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/nordic-22rb-upper 24d592636074 (right side, Nordic NC22-16-Upper-V2)","scaleRef":"rail model from 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%), anchored at takedown lug (91.5,475.5) = frame x 0; 52.0 px/in at the receiver; reads ~1.2% short along the upper","method":"on a 3x crop (py 402)","via":"harvest"}}],"adopt":{"from":"18in","reason":"Twice the resolution and a pin frame in the receiver's plane; the 16 in photo agrees (its ~1.2% short bias allowed for)."}},"ejection_port_pocket_corner_r":{"label":"Ejection port pocket, corner radius","kind":"length","measurements":[{"id":"18in","value":0.16,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/nordic-22rb-upper a379557904df (Nordic, 18 in 22RB upper, true right side, 4096 px)","scaleRef":"pin frame from the upper's lug holes picked on 8x crops: takedown (472, 1335.3), pivot (1362.4, 1334.4) = (0, 0), (6.375, 0): 139.7 px/in, the lugs in the receiver's plane","method":"the recess's corner arcs on a 4x crop (~22 px)","via":"harvest"}}]},"ejection_port_pocket_depth":{"label":"Ejection port pocket depth (its flat floor below the receiver's side)","kind":"length","measurements":[{"id":"section","value":0.232,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/nordic-22rb-upper 5dc13057dabd (Aawee: the NCT3 handguard, straight end-on: the section the receiver shares)","scaleRef":"the section's scale as traced (profiles.front, its height the handguard's), placed on the bore","method":"the side flat's half-width (0.801) less the section's half-width at the pocket's top edge, 1.452 above the pin line (0.569)","via":"harvest"}}],"note":"A flat-floored recess's outline runs out on the section's upper face where that face comes down to its floor: its top edge (1.452) gives the depth through the section. Since 2026-10-02 the section is the handguard's (the owner: the two match); the old section's chamfer gave 0.23 the same way."},"bolt_catch_relief_rear_x":{"label":"Bolt catch relief (an arch cut in the receiver's lower left edge), rear foot, X","kind":"length","measurements":[{"id":"left","value":2.555,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/nordic-22rb-upper 2b348f6a5149 (left side, NC22RB-UPPER-16-KIT_3_HR)","scaleRef":"rail model from 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%), anchored at takedown lug (1853.5,1074.5) = frame x 0; 84 px/in","method":"the arch's rear foot on a 5x crop with frame gridlines","via":"harvest"}}]},"bolt_catch_relief_front_x":{"label":"Bolt catch relief, front foot, X","kind":"length","measurements":[{"id":"left","value":3.473,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/nordic-22rb-upper 2b348f6a5149 (left side, NC22RB-UPPER-16-KIT_3_HR)","scaleRef":"rail model from 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%), anchored at takedown lug (1853.5,1074.5) = frame x 0; 84 px/in","method":"the arch's front foot on the same crop","via":"harvest"}}]},"bolt_catch_relief_top_y":{"label":"Bolt catch relief, top, Y","kind":"length","measurements":[{"id":"left","value":0.6,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/nordic-22rb-upper 2b348f6a5149 (left side, NC22RB-UPPER-16-KIT_3_HR)","scaleRef":"rail model from 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%), anchored at takedown lug (1853.5,1074.5) = frame x 0; 84 px/in","method":"the arch's crown on the same crop (its peak near x 3.02)","via":"harvest"}}]},"handguard_bottom_y":{"label":"Handguard's underside (its bottom flat), Y","kind":"length","measurements":[{"id":"rail-height","value":0.051,"unit":"in","pm":0.07,"source":{"type":"derived","expr":"{.rail_top_above_pin} - 2.039in","via":"harvest"},"note":"The receiver's rail top less the side photos' height (handguard_height's `flatlay` and `right-photo`, 2.039 and 2.038): what was drawn until 2026-10-02."},{"id":"axis","value":0.0765,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{.handguard_center_y} - {.handguard_width} / 2","via":"harvest"},"note":"Half the width across the flats below the handguard's centre, which is on the barrel's axis."}],"adopt":{"from":"axis","reason":"The handguard is centred on the barrel (measured: handguard_above_barrel), and its section is as tall below its centre as it is wide across the flats. The right photo's underside (0.088) and the end view's height under the handguard's rail (0.091) agree within 0.01; the older figure rested on a rail top the side photos read 0.05 high."},"note":"Where the handguard's end section (profiles.front, traced from the NCT3's end view) sits. Until 2026-10-02 it was the receiver's rail top less the handguard's side-view height (0.03), which put the handguard's bore 0.047 in below the barrel (M6's review, finding 29). The side photos read the handguard's rail top 0.05 high along its length (a trend the lens gives: handguard_rail_step), so a height hung from the true rail top came out that much low. Three readings that don't use that height agree on 0.08 to 0.09: the barrel's axis (handguard_above_barrel), the right photo's own underside in its pin frame (0.088, profiles.side), and the handguard's rail top less the end view's height (2.062 − 1.971 = 0.091)."},"handguard_width":{"label":"Handguard width (Z), across the side flats","kind":"length","measurements":[{"id":"photo-sister","value":1.45,"unit":"in","pm":0.09,"source":{"type":"photo","photo":"references/nordic-22rb-upper 4b360099f39a (a different length/model of Nordic 22 upper, same-family handguard per the user; supplied in chat)","scaleRef":"the top rail's front end, 0.835 in wide (std.picatinny.top_width), in the same plane as the handguard's front face","method":"front-face width over rail-head width, both measured horizontally in the face plane (≈225 px / 130 px); the far side's widest point is partly hidden by the barrel, so this may read slightly low","via":"user"}},{"id":"nct3-od","value":1.602,"unit":"in","pm":0.004,"source":{"type":"derived","expr":"{.handguard_od}","via":"harvest"},"note":"The NCT3's listed 40.7 mm, across the side flats (handguard_od's note)."},{"id":"end-ratio","value":1.653,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/nordic-22rb-upper 5dc13057dabd (Aawee: the NCT3 handguard, straight end-on, transparent background)","scaleRef":"nordic-22rb-upper.handguard_height (2.04 ± 0.058, the 22RB's side photos), the same section's bottom flat to rail top","method":"outer silhouette 320 px across the side flats (rows 360–390) over 395 px bottom flat to rail top (rows 149–543), × 2.04; ± is the height's (the near face is one plane; the rail's end may sit a little behind it)","via":"harvest"}},{"id":"user","value":1.605,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/nordic-22rb-upper 2cd733a9d284, 0dad4e900d85 (the user's own 22RB, the muzzle end straight on, the rail at the bottom, a tape across above; 2026-10-03); references/nordic-22rb-upper bdb43e3235ed, 7f994902ea3b (the user's own 22RB from below and from above, straight down from 5 to 7 ft; 2026-10-03)","scaleRef":"the rail head's widest row end on (473 and 475 px = 0.835, carried 0.085 in nearer to the octagon's plane); the rail's pitch and the M-LOK pitch from above and below","method":"across the side flats: 1.61 to 1.62 end on (921 and 923 px; the rail head's sharp corners lose a pixel or two to blur, which makes it 0.5% large), 1.58 to 1.60 from above and below","via":"user"}}],"adopt":{"from":"nct3-od","reason":"A listed figure for the handguard family sold as the original's, read across the flats as its own end view shows; the end view's proportions with the 22RB's height agree (1.65 ± 0.06). The sister model's 1.45 came from a 3/4 view."},"note":"No Nordic figure for the 22RB's handguard. The NCT3 (the handguard family Aawee sells as the original's) is listed at 40.7 mm outer diameter, which its straight end view shows to be across the side flats (handguard_od); the end view's width-to-height ratio with the 22RB's side-view height agrees. A sister model's 3/4 shot gave 1.45 (M2): read as a ratio to the rail head's width in a view that foreshortens the body more than the rail's narrow front face, it reads low, and stays as a visible conflict. The user found about 1.6 in OD quoted online (2026-09-30, link not recorded), which this matches."},"width":{"label":"Receiver width across its side flats (Z), behind the flare to the handguard","kind":"length","measurements":[{"id":"rear-top","value":1.38,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/nordic-22rb-upper 11e268939f9f (Nordic, looking forward down the receiver from the rear)","scaleRef":"the rail's recoil grooves span the full 0.835 in head (std.picatinny.top_width) on the same image rows as the body's silhouette","method":"body silhouette width over groove length on the same rows (1.28–1.35 in raw across rows 500–560, ≈160 px grooves). The body's widest line sits ~1 in below the rail top, so it's ~1.5 in farther from the camera; the receiver's own taper along the photo (~3.5%/in) puts it ~5% too small. Corrected ≈1.34–1.42 in.","via":"harvest"}},{"id":"owner","value":1.602,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{.handguard_width}","via":"user"},"note":"The handguard's width across its side flats, as the user says the receiver's section matches the handguard's (2026-10-02)."},{"id":"user","value":1.31,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/nordic-22rb-upper bdb43e3235ed, 7f994902ea3b (the user's own 22RB from below and from above, straight down from 5 to 7 ft; 2026-10-03)","scaleRef":"the handguard's width in the same views (1.602, the listing's; 1.58 to 1.60 by the rail's pitch and the M-LOK pitch)","method":"the receiver across its side flats against the handguard across its own: 138.6 to 140.6 px against 169.8 to 171.1 from below (0.82), 138.4 to 139.8 against 167.6 to 168.6 from above (0.83). The body widens from one to the other over its last 0.4 in, behind the seam (receiver_flare_start_x)","via":"user"}}],"adopt":{"from":"user","reason":"The user's own upper from above and from below. Its owner's \"the cross section of the upper receiver seems to match up very closely to the cross section on the handguard\" is the seam, where the receiver has flared to the handguard's section; behind the flare it is 0.82 of it. The earlier rear view's 1.38 ± 0.08 agrees."},"note":"Nordic's parts list calls it an extruded receiver (constant cross-section). The user, who owns the upper (2026-10-02): \"the receiver and hard guard come together nearly along a nearly imperceptible seam. The cross section of the upper receiver seems to match up very closely to the cross section on the handguard on the real thing.\" So its section is the handguard's, and its width the handguard's across the flats. The rear view's reading, taken looking down the receiver with the body's widest line 1.5 in further away than the rail it was scaled by, stays as the conflict it is."},"receiver_flare_start_x":{"label":"Where the receiver begins to widen to the handguard's section, X","kind":"length","measurements":[{"id":"user","value":6.19,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/nordic-22rb-upper bdb43e3235ed (the user's own 22RB from below, straight down; 2026-10-03)","scaleRef":"the handguard's rearmost M-LOK slot in the same view (its opening 9.23 to 10.15 through the side photos' pose: 110.6 px/in)","method":"the body's two edges turn outward at strip px 815 and reach the handguard's width at 858: 6.19 to 6.58, the seam (handguard_rear_x). ± is a 5 px pick on a dark edge over shadow","via":"user"}},{"id":"seam-photo","value":6.22,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/nordic-22rb-upper 584c3ded24e1 (the user's own 22RB, close on the seam from its left; 2026-10-04)","scaleRef":"the rail's own slots beside it in the same view: 250 px a pitch (std.picatinny.slot_pitch) just behind the seam and 270 just ahead of it","method":"the facet that brings the receiver out to the handguard's upper diagonal is a triangle in that diagonal's plane, its base on the seam and its point on the rail neck's line 240 px behind it: 0.38 in (0.36 to 0.39 by which pitch); less than the seam (handguard_rear_x)","via":"user"}}],"adopt":{"from":"user","reason":"Read from below, square on, with a scale in the same plane; the close photo, at its own rail's pitch, has the facet's point 0.03 in nearer the seam, within both."},"note":"How the receiver widens, from the user's close photo of the seam (584c3ded24e1): its own faces run straight on, and each face of the handguard's section comes back over it as a flat facet, a triangle with its base on the seam and its point this far behind it. The rail's break is the same line as the body's seam: the receiver's last tooth ends on it and the handguard begins with a slot."},"charging_handle_t_width":{"label":"Charging handle's T, side to side","kind":"length","measurements":[{"id":"user","value":1.97,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/nordic-22rb-upper 76eb04f42d11, 7f994902ea3b, f07b87dfab90 (the user's own 22RB: the T from above, close and far, and from behind; 2026-10-03)","scaleRef":"the rail's pitch beside it (154.75 px a slot: 393 px/in) in the close photo; the rail's slots in the far one; the receiver's width in the rear view","method":"the T from end to end: 1.967 (773 px, rows 866.9 to 1640.2), 1.98 (216 px at 109.2 px/in), 1.97 (1086.5 px, 0.23 in nearer the lens allowed for)","via":"user"},"note":"0.13 under an AR-pattern T on file (std.ar15.charging_handle_t_width, 2.1 ± 0.05), which the model drew it at."}]},"charging_handle_t_depth":{"label":"Charging handle's T, front to back (its wings, either side of the rail)","kind":"length","measurements":[{"id":"user","value":0.496,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/nordic-22rb-upper 76eb04f42d11 (the user's own 22RB: the receiver's rear end from above, close, the T in the middle of the frame; 2026-10-03)","scaleRef":"the T's own width in the same view and the same plane (charging_handle_t_width, 1.97): 775 px from end to end (columns 940 to 980: 773.7, 777.4, 772.6), 393 px/in, which is also the rail's pitch beside it (154.75 px a slot)","method":"the right wing where it stands clear of the receiver over the floor, front face to rear face along rows 980 and 1000: 193.7 and 195.8 px at luminance 80, 194.3 at 110 (195 px). ± is 3 px at each edge of a matte black part on a bright floor (0.015) and the width's own ± carried over (0.005). The left wing carries the latch, which stands further forward, and isn't read","via":"user"}}],"note":"With rear_behind_pin (the T's rear face) this puts the wings' front faces 0.36 in behind the takedown pin: the T stands astride the receiver's rear face (std.ar15.upper_rear_face_x), 0.24 in of it behind the face and the rest either side of the rail's solid rear end, whose round nose is nested in it. Seen from above the T is a stadium: its two ends are full rounds (the chord across the right wing 35.5, 55.5 and 75.5 px in from its end is 150.0, 174.4 and 187.7 px; a half round of the T's own depth has 150.5, 176.0 and 190.0). Until 2026-10-05 the model drew only what lies behind the rear face, square: half as deep (the model review, 2026-10-05)."},"charging_handle_t_top_y":{"label":"The charging handle's T: its top above the pin line","kind":"length","measurements":[{"id":"user","value":2.047,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/nordic-22rb-upper fc6a01b62b5a (the user's own 22RB: the receiver's rear from its left side, square on, the takedown lug's hole and ten of the rail's slots in frame; 2026-10-05)","scaleRef":"the rail's pitch in the same view (472 px/in over ten slots) and 480 px/in at the T's end, 0.57 in nearer a lens 35 in or more away (charging_handle_t_bottom_y's reading says how)","method":"the T's top at its left end 20.7 px (0.043 in) under the rail's top line at columns 2440 and 2480; less than rail_top_above_pin by that. ± is 4 px and the rail top's own","via":"user"}}],"note":"The T's top is a little under the rail's, 0.04 in: from behind, the rail's tongue shows over it. With charging_handle_t_bottom_y the T is 0.45 in tall; the rear view straight on has 0.43 between its top and its rear face's lower edge, which is the upper edge of a chamfer along its underside."},"charging_handle_slot_top_y":{"label":"The charging handle's T: the upper side of the slot across its left end, above the pin line","kind":"length","measurements":[{"id":"user","value":1.846,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/nordic-22rb-upper fc6a01b62b5a (the user's own 22RB: the receiver's rear from its left side, square on, the takedown lug's hole and ten of the rail's slots in frame; 2026-10-05)","scaleRef":"the rail's pitch in the same view (472 px/in over ten slots) and 480 px/in at the T's end, 0.57 in nearer a lens 35 in or more away (charging_handle_t_bottom_y's reading says how)","method":"the upper block's underside at the T's left end, 117 px (0.244 in) under the rail's top line at columns 2440 and 2480 (rows 639.5 and 640.9)","via":"user"}}],"note":"The T's left end is sawn across, front to back: a block 0.20 in thick above, a jaw 0.10 below, and the latch's tail in the slot between (0.147 in, charging_handle_slot_bottom_y). The rear view straight on has the same three: 0.20, 0.12 and the jaw's rear face."},"charging_handle_slot_bottom_y":{"label":"The charging handle's T: the lower side of the slot across its left end, above the pin line","kind":"length","measurements":[{"id":"user","value":1.699,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/nordic-22rb-upper fc6a01b62b5a (the user's own 22RB: the receiver's rear from its left side, square on, the takedown lug's hole and ten of the rail's slots in frame; 2026-10-05)","scaleRef":"the rail's pitch in the same view (472 px/in over ten slots) and 480 px/in at the T's end, 0.57 in nearer a lens 35 in or more away (charging_handle_t_bottom_y's reading says how)","method":"the lower jaw's top at the T's left end, 187.8 px (0.391 in) under the rail's top line at column 2480 (row 710.1)","via":"user"}}]},"charging_handle_slot_length":{"label":"The charging handle's T: the slot across its left end, from that end to where it stops","kind":"length","measurements":[{"id":"user","value":0.81,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/nordic-22rb-upper 953843d0ce18 (the user's own 22RB: the rear end straight on, close, the upper standing on its muzzle; 2026-10-05)","scaleRef":"the T's own width in the plane of its rear face (charging_handle_t_width: 1670.3 px end to end, 848 px/in)","method":"the slot in the rear face from the T's left end (column 145.9) to its end behind the latch's spring (the spring's coils at columns 758 to 819, the slot's end at 835): 689 px. ± is where the slot's end is behind the coils","via":"user"}}],"note":"Seen from behind the slot is open at the T's left end and runs 0.81 in toward the middle: the latch's tail, then its spring, coiled across the slot."},"charging_handle_recess_r":{"label":"The charging handle's T: the round recess in its front for the rail's nose, radius","kind":"length","measurements":[{"id":"user","value":0.455,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/nordic-22rb-upper b8e5873d5ebc (the user's own 22RB: the receiver's rear end from above, close, the handle home; 2026-10-05)","scaleRef":"the T's own width in the rail's plane (charging_handle_t_width: 1318.4 px, 669 px/in); a tooth's top flat (437.7 px for the standard's 0.656: 667) and slot 0's front wall (1.755 in ahead of the T's rear face for the ledger's 1.758) agree","method":"the recess's wall at the T's top: on the centre line 99 px ahead of the T's rear face, and at the T's front face a chord 584 px across: a circle of 297.6 px (0.446 in). The handle out of the upper from above (c8a014aa1043, at its own T's width: 635 px/in) has the same wall 0.169 in ahead of the rear face and a chord of 0.895 in at the front face: 0.465. The middle of the two; ± covers both","via":"user"}}],"note":"From above the T's front is cut round for the rail's nose: a circle wider than the nose (rail_tongue_width), its centre ahead of the T's front face, down to the level the handle's plate is at (charging_handle_plate_top_y). Until 2026-10-05 the model cut it square."},"charging_handle_recess_web":{"label":"The charging handle's T: what is left of it behind the round recess, on the centre line","kind":"length","measurements":[{"id":"user","value":0.155,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/nordic-22rb-upper b8e5873d5ebc (the user's own 22RB: the receiver's rear end from above, close, the handle home; 2026-10-05)","scaleRef":"the T's own width in the rail's plane (charging_handle_t_width: 1318.4 px, 669 px/in); a tooth's top flat (437.7 px for the standard's 0.656: 667) and slot 0's front wall (1.755 in ahead of the T's rear face for the ledger's 1.758) agree","method":"the T's rear face to the recess's wall on the centre line: 99.2 px (0.148 in); 0.169 on the handle out of the upper (c8a014aa1043). ± covers both","via":"user"}}]},"charging_handle_plate_top_y":{"label":"The charging handle: the top of its plate ahead of the T, above the pin line","kind":"length","measurements":[{"id":"user","value":1.89,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/nordic-22rb-upper fc6a01b62b5a (the user's own 22RB: the receiver's rear from its left side, square on, the takedown lug's hole and ten of the rail's slots in frame; 2026-10-05)","scaleRef":"the rail's pitch in the same view (472 px/in over ten slots) and 480 px/in at the T's end, 0.57 in nearer a lens 35 in or more away (charging_handle_t_bottom_y's reading says how)","method":"the plate's left edge under the rail's tongue: its top 8 px under the tongue's underside (row 619.9 at column 2150; the tongue's underside 611.5), 0.203 in under the rail's top line. The handle out of the upper from its side (ee68cec1e113) has the plate's top 0.145 in under the T's: 1.90","via":"user"}}],"note":"Ahead of the T the handle is a plate a step lower than the T's top, as wide as the rail's tongue where it enters the receiver and flared out to the T's front face (profiles.handle). The rail's tongue stands over it; the round recess in the T is cut down to it."},"charging_handle_latch_thickness":{"label":"The charging handle's latch: how thick it is, top to bottom","kind":"length","measurements":[{"id":"user","value":0.124,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/nordic-22rb-upper fc6a01b62b5a (the user's own 22RB: the receiver's rear from its left side, square on, the takedown lug's hole and ten of the rail's slots in frame; 2026-10-05)","scaleRef":"the rail's pitch in the same view (472 px/in over ten slots) and 480 px/in at the T's end, 0.57 in nearer a lens 35 in or more away (charging_handle_t_bottom_y's reading says how)","method":"the latch's arm where its end stands in the receiver's window, its lit side face between rows 659.5 and 718.2 at column 1937: 58.7 px at the rail's 472 px/in; 0.125 at column 2200 (rows 655 to 715)","via":"user"}}],"note":"The latch is a flat piece lying in the T's slot (charging_handle_slot_top_y, charging_handle_slot_bottom_y): its pad at the T's left end, its arm forward along the receiver to a tooth that points inward (profiles.handle, the feature `latch`)."},"rail_tongue_width":{"label":"The rail's rear end behind the standard's head: the tongue, side to side","kind":"length","measurements":[{"id":"user","value":0.64,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/nordic-22rb-upper b8e5873d5ebc (the user's own 22RB: the receiver's rear end from above, close, the handle home; 2026-10-05)","scaleRef":"the T's own width in the rail's plane (charging_handle_t_width: 1318.4 px, 669 px/in); a tooth's top flat (437.7 px for the standard's 0.656: 667) and slot 0's front wall (1.755 in ahead of the T's rear face for the ledger's 1.758) agree","method":"the tongue from above between its two upright sides: 416 to 425 px at columns 1000 and 1350 (0.625 to 0.64 at 667 px/in), the lower side's edge under its own shadow; its edges broken 0.03 to 0.045 in. A tooth's top flat in the same view is 0.656 (the standard's)","via":"user"}}],"note":"From rail_rear_x back the rail has no shoulders: a tongue as wide as the rail's top flat, its sides upright, its rear end a half round nested in the T's recess. It stands over the charging handle's plate (rail_tongue_bottom_y), which is how the handle gets into the receiver."},"rail_tongue_rear_x":{"label":"The rail's tongue: its round nose's rearmost point, X","kind":"length","measurements":[{"id":"user","value":-0.684,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/nordic-22rb-upper b8e5873d5ebc (the user's own 22RB: the receiver's rear end from above, close, the handle home; 2026-10-05)","scaleRef":"the T's own width in the rail's plane (charging_handle_t_width: 1318.4 px, 669 px/in); a tooth's top flat (437.7 px for the standard's 0.656: 667) and slot 0's front wall (1.755 in ahead of the T's rear face for the ledger's 1.758) agree","method":"the nose's outline on the centre line, 118.3 px ahead of the T's rear face (column 679.1), less rear_behind_pin; its top flat's own round ends 0.097 in ahead of that (column 743.8). The nose is a half round of the tongue's width: its straight sides begin 0.31 in ahead of its tip","via":"user"}}]},"rail_tongue_bottom_y":{"label":"The rail's tongue: its underside above the pin line, where it stands over the charging handle's plate","kind":"length","measurements":[{"id":"user","value":1.905,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/nordic-22rb-upper fc6a01b62b5a (the user's own 22RB: the receiver's rear from its left side, square on, the takedown lug's hole and ten of the rail's slots in frame; 2026-10-05)","scaleRef":"the rail's pitch in the same view (472 px/in over ten slots) and 480 px/in at the T's end, 0.57 in nearer a lens 35 in or more away (charging_handle_t_bottom_y's reading says how)","method":"the tongue's lower edge from the left, a straight line from the latch's window back to the T: 87.4 px (0.185 in) under the rail's top line at column 2150 (row 611.5)","via":"user"}}]},"latch_window_front_x":{"label":"The receiver's window for the charging handle's latch, on its left: its front end, X","kind":"length","measurements":[{"id":"user","value":0.446,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/nordic-22rb-upper fc6a01b62b5a (the user's own 22RB: the receiver's rear from its left side, square on, the takedown lug's hole and ten of the rail's slots in frame; 2026-10-05)","scaleRef":"the rail's pitch in the same view (472 px/in over ten slots) and 480 px/in at the T's end, 0.57 in nearer a lens 35 in or more away (charging_handle_t_bottom_y's reading says how)","method":"the window's front edge at column 1890 (its wall's shadow to 1909.6): 115.9 px behind slot 0's rear wall (column 1774.1, the ledger's 0.692)","via":"user"}}],"note":"On the receiver's left, under the rail, an upright window with round ends is cut into the wall: the latch's arm lies along the receiver to it and its tooth drops in. Seen square on from the left; how deep it is cut isn't read (the model cuts it to the latch's tooth and a clearance)."},"latch_window_rear_x":{"label":"The receiver's window for the charging handle's latch: its rear end, X","kind":"length","measurements":[{"id":"user","value":0.245,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/nordic-22rb-upper fc6a01b62b5a (the user's own 22RB: the receiver's rear from its left side, square on, the takedown lug's hole and ten of the rail's slots in frame; 2026-10-05)","scaleRef":"the rail's pitch in the same view (472 px/in over ten slots) and 480 px/in at the T's end, 0.57 in nearer a lens 35 in or more away (charging_handle_t_bottom_y's reading says how)","method":"the window's rear edge at column 1985 between rows 620 and 700","via":"user"}}]},"latch_window_top_y":{"label":"The receiver's window for the charging handle's latch: its top, above the pin line","kind":"length","measurements":[{"id":"user","value":1.949,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/nordic-22rb-upper fc6a01b62b5a (the user's own 22RB: the receiver's rear from its left side, square on, the takedown lug's hole and ten of the rail's slots in frame; 2026-10-05)","scaleRef":"the rail's pitch in the same view (472 px/in over ten slots) and 480 px/in at the T's end, 0.57 in nearer a lens 35 in or more away (charging_handle_t_bottom_y's reading says how)","method":"the inner edge of the window's upper round at column 1937 (row 591.8), 66.4 px under the rail's top line","via":"user"}}]},"latch_window_bottom_y":{"label":"The receiver's window for the charging handle's latch: its bottom, above the pin line","kind":"length","measurements":[{"id":"user","value":1.585,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/nordic-22rb-upper fc6a01b62b5a (the user's own 22RB: the receiver's rear from its left side, square on, the takedown lug's hole and ten of the rail's slots in frame; 2026-10-05)","scaleRef":"the rail's pitch in the same view (472 px/in over ten slots) and 480 px/in at the T's end, 0.57 in nearer a lens 35 in or more away (charging_handle_t_bottom_y's reading says how)","method":"the window's lower round at column 1937 (row 763.5), 238.2 px under the rail's top line","via":"user"}}]},"handguard_groove_offset":{"label":"Handguard: the fine groove engraved each side of every M-LOK row, from the row's centre line","kind":"length","measurements":[{"id":"user","value":0.21,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/nordic-22rb-upper 0dfba70ae389 (the user's own 22RB: the receiver's underside and the handguard's rear from below, close; 2026-10-05)","scaleRef":"the M-LOK slots in the same face: their rear ends 268.7 px apart for the standard's 40 mm (std.mlok.slot_pitch: 170.6 px/in), a slot's own width 47 px for its 7 mm","method":"the dark line each side of the row on the bottom face, from the slot's middle (row 983.4): 33.6, 35.2 and 36.6 px above it and 38.4 below at columns 1860, 1900 and 1980. The close view of the seam from the right (74a0161414d1, the rail's pitch 408 px/in) has the side face's two 169 px apart: 0.207 each. ± covers the four and 2 px","via":"user"}}],"note":"The user, 2026-10-05: \"can we add some of the detailing on the Nordic upper (eg. Those engraved lines on the upper)\". Every face that has a row of M-LOK slots has a fine groove along each side of it, the same distance off on each face: on the right side the side faces two are 0.414 in apart and the upper diagonals 0.357 as that face is seen from the side. A second line outside each, in the view from below, is the faces own edge (the flats corner, 0.27 out on the bottom face), not a groove."},"handguard_groove_width":{"label":"Handguard: the engraved grooves, across","kind":"length","measurements":[{"id":"user","value":0.044,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/nordic-22rb-upper 74a0161414d1 (the user's own 22RB: the receiver's right side around the ejection port, square on, the seam and the handguard's rear in frame; 2026-10-05)","scaleRef":"the rail's pitch in the same view (twelve teeth 160.9 px apart: 408 px/in); the side face is 0.4 in nearer the lens than the rail's edge","method":"down column 2450, the two grooves that are clear of a face's corner: the upper diagonal's upper one from its lit rim to the far side of its shadow (rows 777.1 to 795.6: 18.5 px) and the side face's upper one (990.4 to 1007.8: 17.4 px): 0.045 and 0.043. From below (0dfba70ae389, 170.6 px/in) the shadowed wall alone is 3.7 to 4 px: half of it. ± is 3 px","via":"user"}}],"note":"A round-bottomed groove: from the right and close, each is a lit wall beside a shadowed one. The first reading took the shadowed wall alone for the groove (3.7 to 4 px from below, 0.022 in) and the model drew hairlines; the user, seeing them: \"Those lines dont look very good\". How deep they are cut isnt read (drawn a third as deep as they are wide, round-bottomed, their ends tapering out as the close view has them)."},"handguard_groove_overrun":{"label":"Handguard: how far the engraved grooves run past the ends of the slots they lie beside","kind":"length","measurements":[{"id":"user","value":0.3,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/nordic-22rb-upper 0dfba70ae389 (the user's own 22RB: the receiver's underside and the handguard's rear from below, close; 2026-10-05)","scaleRef":"the M-LOK slots in the same face (170.6 px/in by their pitch)","method":"the upper groove's pointed rear end on the bottom face (columns 1737 to 1748 along row 948) behind the short slot's rear end (column 1793.8): 46 to 57 px","via":"user"}}],"note":"On the bottom face and the two faces either side of it the grooves begin this far behind the rearmost (short) slot; on every face they end about as far ahead of the foremost (0.26 in on the right side from 5 ft, d633f1bf49ff, at 107 px/in: within this). On the two sides and the two upper faces they begin near the seam instead (handguard_groove_upper_rear_x)."},"handguard_groove_upper_rear_x":{"label":"Handguard: where the engraved grooves begin on its two sides and its two upper faces, X","kind":"length","measurements":[{"id":"user","value":6.82,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/nordic-22rb-upper 74a0161414d1 (the user's own 22RB: the receiver's right side around the ejection port, square on, the seam and the handguard's rear in frame; 2026-10-05)","scaleRef":"the rail's pitch in the same view (twelve teeth 160.9 px apart: 408 px/in) and the seam itself (column 2145, handguard_rear_x)","method":"the grooves' pointed rear ends on the side face, 88 to 90 px ahead of the seam (column 2233): 0.22 in, more than handguard_rear_x by that. ± is where a point ends (10 px) and the side face being 0.4 in nearer the lens than the rail's edge","via":"user"}}],"note":"On the sides and the upper diagonals the grooves run back past the first slot, under Nordic's name and the M-LOK mark, to a pointed end just ahead of the seam."},"lug_hole_d":{"label":"Receiver: the takedown and pivot lugs' pin holes","kind":"length","measurements":[{"id":"tdp","value":0.251,"unit":"in","pm":0.001,"stated":".250 DIA +.002 THRU (the takedown lug's, CSK .31 DIA X 90 INCL THIS SIDE ONLY); .250 DIA +.001 THRU (the pivot lug's)","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: side elevation; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}},{"id":"user","value":0.257,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/nordic-22rb-upper fc6a01b62b5a (the user's own 22RB: the receiver's rear from its left side, square on, the takedown lug's hole and ten of the rail's slots in frame; 2026-10-05)","scaleRef":"the rail's pitch in the same view (472 px/in at the rail's near edge; 470 at the lug's face, 0.19 in further from a lens 35 in or more away)","method":"the takedown lug's hole against the floor, top to bottom (column 2104: rows 1456.2 to 1577.0, 120.8 px). Its near rim, which the drawing countersinks on one side","via":"user"}}],"adopt":{"from":"tdp","reason":"The standard the lugs are made to: they take a lower's .250 pins. The photo reads the hole's near rim, 0.006 in more, within its own ±."},"note":"The user, 2026-10-05: \"Did you add the holes in the two pins on the upper receiver?\" They were not in the model: the traced outline fills them. The lugs take a lowers .250 pins."},"handguard_center_y":{"label":"The handguard's centre (the octagon's, and the bore's) above the pin line","kind":"length","measurements":[{"id":"octagon","value":0.852,"unit":"in","pm":0.07,"source":{"type":"derived","expr":"{.rail_top_above_pin} - 2.039in + {.handguard_width} / 2","via":"user"},"note":"A regular octagon half its width above a bottom flat hung from the receiver's rail top by the side photos' height (2.039): where the bore and the M-LOK faces were centred from M5 to 2026-10-02, 0.047 below the bore axis (0.8775)."},{"id":"barrel","value":0.8775,"unit":"in","pm":0.017,"source":{"type":"derived","expr":"{.bore_axis_above_pin} + {.handguard_above_barrel}","via":"harvest"},"note":"The barrel's axis, and what the right photo reads the handguard's centre to stand above it."}],"adopt":{"from":"barrel","reason":"Measured against the barrel in the one side photo that is level (handguard_above_barrel): the handguard is centred on it within 0.015 in. The older figure put it 0.047 below, which showed on looking into the handguard's mouth; it mixed the standard's bore height with a handguard height read against a rail top the lens raised."}},"handguard_above_barrel":{"label":"Handguard's centre above the barrel's axis","kind":"length","measurements":[{"id":"right","value":0.009,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/nordic-22rb-upper 24d592636074 (right side, Nordic NC22-16-Upper-V2, 1200 px)","scaleRef":"the photo's rail model (02-24d592636074.calib.json) for the last step only, 0.0200 in/px across at the muzzle end; the comparison is between rows","method":"the handguard's centre as the midpoint of the two rows of through-slots (the upper and lower diagonal faces' slots, each seen through to the white ground: rows crossing the 50% level, 84 columns from px 560 to 1077; a line fitted, 0.12 px rms, which carries the photo's 0.44° tilt) against the barrel's axis (the mean of its two edges at their own 50% level, 34 columns of bare barrel at px 1112–1145: row 424.40, quartiles 424.39 and 424.45), the line read at the barrel's columns: 423.95, so 0.45 px above the axis. ± is half a pixel for each of the two readings and what one degree of elevation would move the slots' rows","via":"harvest"},"note":"The user's own upper, photographed from the muzzle end (d98f75b9de4f, 2026-10-02), shows the barrel in the middle of the handguard's mouth: no scale in it, and the muzzle stands nearer the lens than the handguard, so it corroborates and isn't a second measurement. Checks in the same photo: the barrel's axis is 39.2 px above the handguard's underside, 0.785 to 0.805 in by the scale taken (half of 1.602 is 0.801); and of the way from the underside to the rail's tooth tops the axis stands at 0.396, where the drawing until now had the barrel at 0.417 and the handguard's centre at 0.394."},{"id":"user","value":0,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/nordic-22rb-upper 14dc07bfde38, d633f1bf49ff (the user's own 22RB, left and right side, square on from 5 to 7 ft; 2026-10-03)","scaleRef":"the rail's 49 slots and the two lug holes in one fitted camera pose (rail_slot0_x#user)","method":"the handguard's underside is 0.80 below the thread protector's axis in both photos (the underside 0.074 to 0.083 and 0.063 to 0.073 above the pins, the axis 0.864 to 0.874): half its width across the flats, so its octagon is centred on the barrel","via":"user"}}],"adopt":{"from":"user","reason":"The user's own upper, both sides, square on. The right product photo's 0.009 ± 0.015 agrees."},"note":"Whether the handguard is centred on the barrel, read where both show: at the handguard's front in the right-side photo, which is level (its receiver lands on the lower's deck and on the rail top; the slots of the two diagonal faces show through to the background as two rows the same distance above and below the side face's). Nothing here uses a scale across the photo but the last step to inches, and the rail and the pins aren't in it."},"receiver_rail_front_x":{"label":"Receiver rail's front end (the front face of its last tooth), X","kind":"length","measurements":[{"id":"left","value":6.47,"unit":"in","pm":0.035,"source":{"type":"photo","photo":"references/nordic-22rb-upper 2b348f6a5149 (left side, NC22RB-UPPER-16-KIT_3_HR)","scaleRef":"rail model from 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%), anchored at takedown lug (1853.5,1074.5) = frame x 0","method":"the tooth's front face where it meets the rail's lower edge, at x 1305.75 ± 1 px over rows 925–945 on a 16× gridded crop, against the seam's own pick on the body below it (1305 ± 1.5 px over rows 940–1040, handguard_rear_x). One line within a pixel, so the seam's value; ± is the seam's","via":"harvest"}},{"id":"grid","value":6.602,"unit":"in","pm":0.035,"source":{"type":"derived","expr":"{.rail_slot0_x} + 15 * {std.picatinny.slot_pitch} - {std.picatinny.slot_width} / 2","via":"harvest"},"note":"Where slot 15's rear edge is by the slot grid at the standard's slot width; ± is the first slot's."},{"id":"whole-tooth","value":6.597,"unit":"in","pm":0.036,"source":{"type":"derived","expr":"{.handguard_rail_slot0_x} - {std.picatinny.slot_width} / 2 - {.receiver_rail_last_tooth_deficit}","via":"user"},"note":"The rear edge of the handguard's first slot by the slot grid, less what the tooth behind it measures narrow (receiver_rail_last_tooth_deficit, from the user's own upper seen from above): the tooth's front face."}],"adopt":{"from":"whole-tooth","reason":"The receiver's rail ends with a whole tooth, measured against its neighbours on the user's own upper (two frames, within 0.005 in), and the slots are where the optics are indexed: so its front face is the slot grid's. The side photos put that face on the seam's line within a pixel; the seam's own reading there (6.47 on the near wall, 6.49 carried to the rail's plane) agrees within its ±, and drew the tooth 0.05 and 0.03 in narrow."},"note":"The receiver's rail ends with a whole tooth, the one between slots 14 and 15, whose front face is the receiver's front face: in the left photo (16× gridded crop, x 1262–1352, rows 884–944) the seam's line on the body runs up into that tooth's front face without a jog, and the slot ahead of it is cut in the handguard. By the slot grid at the standard's slot width the same face would be 0.05 further forward: the seam is read on the receiver's near wall, 0.80 in nearer the lens than the rail's mid-plane (half the receiver's width), which from this lens (about 100 in away: the teeth's silhouettes widen by 0.0069 in per inch off its axis, at px 1005) reads about 0.03 short; and the 22RB's slots measure 0.226 wide on the lens's axis, 0.02 over the standard's .206. The two agree once those are allowed for."},"rail_gap":{"label":"Gap between the receiver's rail and the handguard's, at the seam","kind":"length","measurements":[{"id":"left","value":0.006,"unit":"in","pm":0.006,"stated":"between touching and one pixel (0.012 in)","source":{"type":"photo","photo":"references/nordic-22rb-upper 2b348f6a5149 (left side, NC22RB-UPPER-16-KIT_3_HR)","scaleRef":"rail model from 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%), 83.6 px/in at the seam","method":"the seam's dark line where it crosses the rail's side (rows 925–945 on a 16× gridded crop) is one pixel wide or less; the value is the middle of that, the ± its whole range","via":"harvest"}}],"note":"The two parts butt: the seam is a line, not a slot. Its width isn't resolved in the 2000 px photo."},"handguard_rail_rear_x":{"label":"Handguard rail's rear end (where its first slot's floor begins), X","kind":"length","measurements":[{"id":"derived","value":6.603,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.receiver_rail_front_x} + {.rail_gap}","via":"harvest"}}],"note":"The handguard's rail starts at the seam with a slot, not a tooth (receiver_rail_front_x's note)."},"handguard_rail_slot0_x":{"label":"Handguard rail's first slot centre (slot 15 of the run), X","kind":"length","measurements":[{"id":"left","value":6.621,"unit":"in","pm":0.035,"source":{"type":"photo","photo":"references/nordic-22rb-upper 2b348f6a5149 (left side, NC22RB-UPPER-16-KIT_3_HR)","scaleRef":"rail model from 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%), anchored at takedown lug (1853.5,1074.5) = frame x 0","method":"slot 15's centre (counted from the rear) along the rail model, which puts every slot on one pitch within 0.0027 in; ± is 3× rail rms plus edge and anchor error","via":"harvest"},"note":"The handguard rail's first slot: the first whose centre is ahead of the seam."},{"id":"grid","value":6.705,"unit":"in","pm":0.035,"source":{"type":"derived","expr":"{.rail_slot0_x} + 15 * {std.picatinny.slot_pitch}","via":"harvest"},"note":"Fifteen pitches ahead of the receiver's first slot."}],"adopt":{"from":"grid","reason":"The slots are drawn where the optics are indexed (slot 0 plus a whole number of pitches); the photo puts the handguard's first slot there within 0.002 in."},"note":"The handguard's slots continue the receiver's pitch: the rail fit puts all 49 on one pitch within 0.0027 in, and the spacing across the seam is 33.01 px in the left photo against 32.77 to 33.19 for its four neighbours either side (19.87 against 19.59 to 19.95 in the right one). So the optics' one run of slots is what is drawn."},"handguard_rail_step":{"label":"Handguard rail's top against the receiver rail's, at the seam (up positive)","kind":"length","measurements":[{"id":"left","value":-0.0076,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/nordic-22rb-upper 2b348f6a5149 (left side, NC22RB-UPPER-16-KIT_3_HR)","scaleRef":"rail model from 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%), anchored at takedown lug (1853.5,1074.5) = frame x 0","method":"tooth tops (the 50% level between the background and the tooth, over the middle of each tooth) fitted by a line over 7 teeth behind x 6.47 ({.handguard_rear_x}) and 7 ahead of it, the tooth at it left out, and compared there: -0.64 px at 83.6 px/in (scatter about the two lines 0.07 px); ± is half a pixel: the two parts' edges needn't read alike","via":"harvest"},"note":"The handguard's rail top against the receiver's at the seam: negative is lower."},{"id":"right","value":-0.007,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/nordic-22rb-upper 24d592636074 (right side, Nordic NC22-16-Upper-V2)","scaleRef":"rail model from 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%), anchored at takedown lug (91.5,475.5) = frame x 0","method":"tooth tops (the 50% level between the background and the tooth, over the middle of each tooth) fitted by a line over 5 teeth behind x 6.47 ({.handguard_rear_x}) and 5 ahead of it, the tooth at it left out, and compared there: -0.35 px at 50.4 px/in (scatter about the two lines 0.07 px); ± is half a pixel: the two parts' edges needn't read alike","via":"harvest"}}],"adopt":{"from":"left","reason":"The larger photo (83.6 px/in against 50.4); the other side's photo reads the same step."},"note":"The handguard's rail sits a little below the receiver's: two photos, of the two sides, read the same step. Read from the teeth either side of the seam, each side fitted on its own, so the rail's tilt in the photo and the lens's bend are out of it. Along the handguard the rail's top then reads 0.02 to 0.06 in higher toward the muzzle in the same photos (and 2.17 in the flat-lay): a trend over 13 in, which a lens gives and a step doesn't, and which isn't drawn. M5's note that the handguard's rail reads higher was that trend."},"handguard_rail_top_above_pin":{"label":"Handguard rail's top surface above the pin centerline","kind":"length","measurements":[{"id":"derived","value":2.0824,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.rail_top_above_pin} + {.handguard_rail_step}","via":"harvest"}}]},"charging_handle_t_bottom_y":{"label":"The charging handle's T: its underside above the pin line, where it stands behind the receiver","kind":"length","measurements":[{"id":"photo","value":1.56,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/nordic-22rb-upper 24d592636074 (right side, Nordic NC22-16-Upper-V2, 1200 px)","scaleRef":"the traced side profile's (profiles.side)","method":"the outline's corner behind the rear face where the sloped rear end meets the T's underside: (-1.169, 1.56)","via":"harvest"}},{"id":"user","value":1.597,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/nordic-22rb-upper fc6a01b62b5a (the user's own 22RB: the receiver's rear from its left side, square on, the takedown lug's hole and ten of the rail's slots in frame; 2026-10-05)","scaleRef":"the rail's own pitch in the same view (ten slots' rear walls 185.9 px apart, 184.5 to 187.5: 472 px/in) and the T's rear face, which reads 1.595 in behind slot 0's rear wall where the ledger has 1.552: the T's end is 0.57 in nearer the lens than the rail's near edge and 1.6% larger, a lens 35 in or more away; 480 px/in at the T's end. The lug's hole reads 0.252 at its own depth","method":"the T's left end against the floor: its top 20.7 px under the rail's top line (rows 536.2 less 0.0056 a column, by seven tooth tops), its underside 237 px under it at columns 2440 to 2460 (row 758 to 760); ± is 5 px at the two edges and the scale's 1%","via":"user"}}],"adopt":{"from":"user","reason":"The user's own upper, square on from 35 in or more, scaled in the T's own plane; the product photo's corner, 0.037 in lower, is within its own ±."},"note":"Behind the receiver's rear face the traced outline is the receiver's sloped rear end up to here and the handle's T above it, as an AR's handle sits about 0.86 in above the bore (Aero's receiver's latch notch). The 22RB's handle is Nordic's own; a buyer's review on Nordic's page says it is \"compatible with aftermarket latches\": an AR-pattern T (std.ar15.charging_handle_t_width)."},"bolt_flat_bottom_y":{"label":"Bolt, as it shows through the ejection port: the lower edge of its flat face, Y","kind":"length","measurements":[{"id":"user","value":0.985,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/nordic-22rb-upper e421a9af0aa7 (the user's own 22RB, the receiver's right side from close, the ejection port near the frame's middle; 2026-10-03)","scaleRef":"the port's own pocket in the same photo: its two ends 347.7 px apart along the rifle for the ledger's 1.797 in (ejection_port_pocket_rear_x to ejection_port_pocket_front_x: 193.5 px/in on the receiver's side face) and its lower edge for the height (ejection_port_pocket_bottom_y); the photo lies 2.7 degrees off level, by the pocket's edges and the bolt's own","method":"the line where the flat ends and the bright band under it begins, at photo x 1300, 1360 and 1420: rows 1125, 1128, 1131 (1.007 at the side face's scale). Read at the side face's scale and carried to the bolt's face, which stands further from the lens by an amount no photo on file gives: between the pocket's floor (0.23 in in) and 0.45 in. The lens was 12.7 in off the side face (the lug holes read 184 px/in, 0.655 in behind it) and over a point 0.6 in behind the port's middle and 0.7 above it (the frame's middle), so what is on the bolt reads 2 to 4% near that point: the figure has 0.34 in of depth allowed for (0.022 here). ± is the rest of that (0.01), the picks (0.01) and the pocket's own ± as a scale (0.01)","via":"user"}}],"note":"What the user's close photo shows of the bolt through the port (the model review, 2026-10-05: it was drawn as the bore's round bar, polished): a flat, matte, bead-blasted face from this line up to bolt_flat_top_y, between bolt_rear_x and bolt_front_x, with a hollow pin in it (bolt_pin_*); under the line a bright band 0.12 in tall that ends 0.866 above the pin line, which is the bore's axis (0.8775) within the reading: the round body's own crest, seen from a little above. The model keeps the round body where it was and stands the flat on it at this line; how far the flat really is behind the round's crest, and behind the opening, isn't read."},"bolt_flat_top_y":{"label":"Bolt, as it shows through the ejection port: the upper edge of its flat face, Y","kind":"length","measurements":[{"id":"user","value":1.285,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/nordic-22rb-upper e421a9af0aa7 (the user's own 22RB, the receiver's right side from close, the ejection port near the frame's middle; 2026-10-03)","scaleRef":"the port's own pocket in the same photo: its two ends 347.7 px apart along the rifle for the ledger's 1.797 in (ejection_port_pocket_rear_x to ejection_port_pocket_front_x: 193.5 px/in on the receiver's side face) and its lower edge for the height (ejection_port_pocket_bottom_y); the photo lies 2.7 degrees off level, by the pocket's edges and the bolt's own","method":"the flat's upper edge under the opening's own, at photo x 1330 and 1420: rows 1070 and 1074.5 (1.299 at the side face's scale). Read at the side face's scale and carried to the bolt's face, which stands further from the lens by an amount no photo on file gives: between the pocket's floor (0.23 in in) and 0.45 in. The lens was 12.7 in off the side face (the lug holes read 184 px/in, 0.655 in behind it) and over a point 0.6 in behind the port's middle and 0.7 above it (the frame's middle), so what is on the bolt reads 2 to 4% near that point: the figure has 0.34 in of depth allowed for (0.014 here). ± as bolt_flat_bottom_y's","via":"user"},"note":"0.024 under the opening's upper edge on file (ejection_port_top_y, from Nordic's photos): the photo has a dark line between the two."}]},"bolt_rear_x":{"label":"Bolt, as it shows through the ejection port (closed): its rear end, X","kind":"length","measurements":[{"id":"user","value":3.68,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/nordic-22rb-upper e421a9af0aa7 (the user's own 22RB, the receiver's right side from close, the ejection port near the frame's middle; 2026-10-03)","scaleRef":"the port's own pocket in the same photo: its two ends 347.7 px apart along the rifle for the ledger's 1.797 in (ejection_port_pocket_rear_x to ejection_port_pocket_front_x: 193.5 px/in on the receiver's side face) and its lower edge for the height (ejection_port_pocket_bottom_y); the photo lies 2.7 degrees off level, by the pocket's edges and the bolt's own","method":"where the flat begins along rows 1100 and 1115: photo x 1252 and 1249 (3.681 at the side face's scale). Read at the side face's scale and carried to the bolt's face, which stands further from the lens by an amount no photo on file gives: between the pocket's floor (0.23 in in) and 0.45 in. The lens was 12.7 in off the side face (the lug holes read 184 px/in, 0.655 in behind it) and over a point 0.6 in behind the port's middle and 0.7 above it (the frame's middle), so what is on the bolt reads 2 to 4% near that point: the figure has 0.34 in of depth allowed for (under 0.005 here: it is nearly under the lens). ± as bolt_flat_bottom_y's","via":"user"},"note":"Its upper rear corner is rounded (about 0.08 in by this photo; 0.14 by the square one: bolt_rear_corner_r, drawn since 2026-10-12)."},{"id":"close","value":3.6,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/nordic-22rb-upper 26b2fef5a5a3 (the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05)","scaleRef":"the port's own opening in the same photo, in the flat's plane within 0.02 in: its two ends 1356 px apart along the rifle for the ledger's 1.718 in (789 px/in; bolt_pin_seat_d's), and places counted from the screw's middle in the same photo (photo 1579.5, 875.5: bolt_pin_x, bolt_pin_y), which puts the ledger's other figures of the bolt on their edges here within 0.012 in (its front end at photo 1727 for 1722, the dark bar's rear at 1093 for 1102)","method":"the face's rear edge at mid height, where it is upright: light begins at column 478 along row 930 and at 471 along row 1000 (475: 3.600). ± is 7 px and the frame's","via":"user"},"note":"Square on and four times the other photo's scale. The other read where the flat begins along two rows near its top, through the round of its rear upper corner (bolt_rear_corner_r), which is 0.14 in: 0.08 further forward, as that round is there."}],"adopt":{"from":"close","reason":"The rear end where it is upright, read square on at 789 px/in; the first reading was taken through the corner's round, which its own note says wasn't drawn. Drawn since 2026-10-12, so the end is the end."}},"bolt_front_x":{"label":"Bolt, as it shows through the ejection port (closed): its front end, X","kind":"length","measurements":[{"id":"user","value":5.18,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/nordic-22rb-upper e421a9af0aa7 (the user's own 22RB, the receiver's right side from close, the ejection port near the frame's middle; 2026-10-03)","scaleRef":"the port's own pocket in the same photo: its two ends 347.7 px apart along the rifle for the ledger's 1.797 in (ejection_port_pocket_rear_x to ejection_port_pocket_front_x: 193.5 px/in on the receiver's side face) and its lower edge for the height (ejection_port_pocket_bottom_y); the photo lies 2.7 degrees off level, by the pocket's edges and the bolt's own","method":"where the flat ends along rows 1100 and 1115: photo x 1534 and 1535 (5.147 at the side face's scale). Read at the side face's scale and carried to the bolt's face, which stands further from the lens by an amount no photo on file gives: between the pocket's floor (0.23 in in) and 0.45 in. The lens was 12.7 in off the side face (the lug holes read 184 px/in, 0.655 in behind it) and over a point 0.6 in behind the port's middle and 0.7 above it (the frame's middle), so what is on the bolt reads 2 to 4% near that point: the figure has 0.34 in of depth allowed for (0.035 here, the furthest from the lens: ± 0.013 of it for the depth). ± with the picks (0.01) and the scale (0.01)","via":"user"},"note":"Its upper front corner is cut off (about 0.07 by 0.08 in by this photo; a round of 0.05 by the square one: bolt_front_corner_r, drawn since 2026-10-12). Ahead of it the opening is dark for 0.10 in."}]},"bolt_pin_x":{"label":"Bolt: the hollow pin in its flat face, centre, X","kind":"length","measurements":[{"id":"user","value":5,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/nordic-22rb-upper e421a9af0aa7 (the user's own 22RB, the receiver's right side from close, the ejection port near the frame's middle; 2026-10-03)","scaleRef":"the port's own pocket in the same photo: its two ends 347.7 px apart along the rifle for the ledger's 1.797 in (ejection_port_pocket_rear_x to ejection_port_pocket_front_x: 193.5 px/in on the receiver's side face) and its lower edge for the height (ejection_port_pocket_bottom_y); the photo lies 2.7 degrees off level, by the pocket's edges and the bolt's own","method":"the pin's end, a bright ring round a dark socket: the ring's outer edge from photo x 1483 to 1518 on row 1096 and from row 1077 to 1116 on column 1499, centred (1500.5, 1096.5): 4.969 at the side face's scale. Read at the side face's scale and carried to the bolt's face, which stands further from the lens by an amount no photo on file gives: between the pocket's floor (0.23 in in) and 0.45 in. The lens was 12.7 in off the side face (the lug holes read 184 px/in, 0.655 in behind it) and over a point 0.6 in behind the port's middle and 0.7 above it (the frame's middle), so what is on the bolt reads 2 to 4% near that point: the figure has 0.34 in of depth allowed for (0.03 here). ± as bolt_front_x's","via":"user"}}]},"bolt_pin_y":{"label":"Bolt: the hollow pin in its flat face, centre, Y","kind":"length","measurements":[{"id":"user","value":1.187,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/nordic-22rb-upper e421a9af0aa7 (the user's own 22RB, the receiver's right side from close, the ejection port near the frame's middle; 2026-10-03)","scaleRef":"the port's own pocket in the same photo: its two ends 347.7 px apart along the rifle for the ledger's 1.797 in (ejection_port_pocket_rear_x to ejection_port_pocket_front_x: 193.5 px/in on the receiver's side face) and its lower edge for the height (ejection_port_pocket_bottom_y); the photo lies 2.7 degrees off level, by the pocket's edges and the bolt's own","method":"the same ring's centre (1500.5, 1096.5): 1.204 at the side face's scale. Read at the side face's scale and carried to the bolt's face, which stands further from the lens by an amount no photo on file gives: between the pocket's floor (0.23 in in) and 0.45 in. The lens was 12.7 in off the side face (the lug holes read 184 px/in, 0.655 in behind it) and over a point 0.6 in behind the port's middle and 0.7 above it (the frame's middle), so what is on the bolt reads 2 to 4% near that point: the figure has 0.34 in of depth allowed for (0.017 here). ± as bolt_flat_bottom_y's","via":"user"}}]},"bolt_pin_d":{"label":"Bolt: the hollow pin's diameter (its end, rim to rim)","kind":"length","measurements":[{"id":"user","value":0.196,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/nordic-22rb-upper e421a9af0aa7 (the user's own 22RB, the receiver's right side from close, the ejection port near the frame's middle; 2026-10-03)","scaleRef":"the port's own pocket in the same photo: its two ends 347.7 px apart along the rifle for the ledger's 1.797 in (ejection_port_pocket_rear_x to ejection_port_pocket_front_x: 193.5 px/in on the receiver's side face) and its lower edge for the height (ejection_port_pocket_bottom_y); the photo lies 2.7 degrees off level, by the pocket's edges and the bolt's own","method":"the ring's outer edge: 35 px along the rifle and 39 across it, 37 px at 193.5 px/in and 2.7% more for the face's depth. ± is the two readings' spread (2 px) and the depth's","via":"user"},"note":"Not drawn: the model has the pin's socket alone (bolt_pin_socket_d)."}]},"bolt_pin_socket_d":{"label":"Bolt: the socket in its flat face (a screw's, down a countersunk seat: bolt_pin_seat_d), diameter","kind":"length","measurements":[{"id":"user","value":0.101,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/nordic-22rb-upper e421a9af0aa7 (the user's own 22RB, the receiver's right side from close, the ejection port near the frame's middle; 2026-10-03)","scaleRef":"the port's own pocket in the same photo: its two ends 347.7 px apart along the rifle for the ledger's 1.797 in (ejection_port_pocket_rear_x to ejection_port_pocket_front_x: 193.5 px/in on the receiver's side face) and its lower edge for the height (ejection_port_pocket_bottom_y); the photo lies 2.7 degrees off level, by the pocket's edges and the bolt's own","method":"the dark middle of the ring: 19 px along the rifle (row 1096: 1491 to 1510) and 18 to 19 across it (column 1499: 1088 to 1106), at 193.5 px/in and 2.7% more for the face's depth. ± is 2 px and the depth's","via":"user"}}]},"bolt_pin_seat_d":{"label":"Bolt: the seat round the socket in its flat face, diameter at the face","kind":"length","measurements":[{"id":"user","value":0.205,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/nordic-22rb-upper 26b2fef5a5a3 (the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05)","scaleRef":"the port's own opening in the same photo, in the flat's plane within 0.02 in: its two ends 1356 px apart along the rifle for the ledger's 1.718 in (ejection_port_rear_x to ejection_port_front_x: 789 px/in). The pocket's rim, 0.23 in nearer the lens, reads 820: a lens about 6 in away, so nothing is read across planes","method":"the ring's outer edge along the rifle (row 865: 1497 to 1662, 165 px) and across it (column 1580: 796 to 955, 159 px): 0.209 and 0.202. The dark socket inside it is 86 px along and 68 across, 0.087 to 0.109: bolt_pin_socket_d's 0.101 again. ± is 4 px at each edge and the two directions' difference","via":"user"}}],"note":"The socket in the flat (bolt_pin_socket_d) has a bright ring round it that reaches the flat's upper edge: a seat sunk into the face, twice the socket across. The close photo of 2026-10-05 shows what the \"hollow pin\" is: a screw's socket down a countersunk hole. How deep the seat is isn't read: drawn with a flat floor half the edge's break deep (bolt_top_break), the ring being one tone from its rim to the socket; it had been a cone."},"bolt_rear_corner_r":{"label":"Bolt: the round of its flat faces rear upper corner","kind":"length","measurements":[{"id":"user","value":0.143,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/nordic-22rb-upper 26b2fef5a5a3 (the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05)","scaleRef":"the port's own opening in the same photo, in the flat's plane within 0.02 in: its two ends 1356 px apart along the rifle for the ledger's 1.718 in (789 px/in; bolt_pin_seat_d's), and places counted from the screw's middle in the same photo (photo 1579.5, 875.5: bolt_pin_x, bolt_pin_y), which puts the ledger's other figures of the bolt on their edges here within 0.012 in (its front end at photo 1727 for 1722, the dark bar's rear at 1093 for 1102)","method":"the outline about the corner: the top edge at row 791, the rear edge at column 475, and between them on a circle of 113 px that touches both (at column 520 the outline is at row 815 for the circles 814; at column 500, 835 for 833). ± is 12 px","via":"user"}}],"note":"The faces rear upper corner is a round, not a corner cut off: the outline leaves the top edge about 0.15 in ahead of the rear end and meets the rear edge as far down. The edges break (bolt_top_break) follows it round."},"bolt_front_corner_r":{"label":"Bolt: the round of its flat faces front upper corner","kind":"length","measurements":[{"id":"user","value":0.05,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/nordic-22rb-upper 26b2fef5a5a3 (the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05)","scaleRef":"the port's own opening in the same photo, in the flat's plane within 0.02 in: its two ends 1356 px apart along the rifle for the ledger's 1.718 in (789 px/in; bolt_pin_seat_d's), and places counted from the screw's middle in the same photo (photo 1579.5, 875.5: bolt_pin_x, bolt_pin_y), which puts the ledger's other figures of the bolt on their edges here within 0.012 in (its front end at photo 1727 for 1722, the dark bar's rear at 1093 for 1102)","method":"the top edge is straight to about column 1690 and the front edge from about row 835, the front end at column 1727: a round of 37 to 44 px. ± is 9 px","via":"user"}}],"note":"Smaller than the rear one. The other close photo read it as a corner cut off, about 0.07 by 0.08 in (bolt_front_xs note)."},"bolt_top_break":{"label":"Bolt: the break along its flat faces upper edge, its height as it shows from the side","kind":"length","measurements":[{"id":"user","value":0.054,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/nordic-22rb-upper 26b2fef5a5a3 (the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05)","scaleRef":"the port's own opening in the same photo, in the flat's plane within 0.02 in: its two ends 1356 px apart along the rifle for the ledger's 1.718 in (789 px/in; bolt_pin_seat_d's), and places counted from the screw's middle in the same photo (photo 1579.5, 875.5: bolt_pin_x, bolt_pin_y), which puts the ledger's other figures of the bolt on their edges here within 0.012 in (its front end at photo 1727 for 1722, the dark bar's rear at 1093 for 1102)","method":"down columns 700, 850, 1000 and 1250: the bolts top edge at rows 790 to 791 and the bands lower edge at 832 to 835: 43 px. ± is 6 px","via":"user"}}],"note":"A band of another tone along the faces top, between the face and the bolts top edge, which runs on round the rear upper corner and down the front end. How deep it goes isnt read: drawn at 45 degrees. Below the face the bolt has a taller band of the same kind, from bolt_flat_bottom_y down to the ports lower lip (0.12 in), which is drawn as the round it had been taken for."},"extractor_notch_x":{"label":"Bolt: the half-round cut in its lower edge over the extractor, its middle, X","kind":"length","measurements":[{"id":"user","value":4.798,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/nordic-22rb-upper 26b2fef5a5a3 (the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05)","scaleRef":"the port's own opening in the same photo, in the flat's plane within 0.02 in: its two ends 1356 px apart along the rifle for the ledger's 1.718 in (789 px/in; bolt_pin_seat_d's), and places counted from the screw's middle in the same photo (photo 1579.5, 875.5: bolt_pin_x, bolt_pin_y), which puts the ledger's other figures of the bolt on their edges here within 0.012 in (its front end at photo 1727 for 1722, the dark bar's rear at 1093 for 1102)","method":"along row 1060, 31 px above the slots upper edge, the arch is dark from column 1367 to 1473: its middle at 1420. ± is 6 px and the frames","via":"user"}}],"note":"An arch cut up into the bolts lower band from the slot the extractor lies in, over the extractors raised rear end. extractor_rear_xs note had it at about 4.8 and 0.075 in radius from the other photo."},"extractor_notch_top_y":{"label":"Bolt: the half-round cut over the extractor, its top, Y","kind":"length","measurements":[{"id":"user","value":0.976,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/nordic-22rb-upper 26b2fef5a5a3 (the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05)","scaleRef":"the port's own opening in the same photo, in the flat's plane within 0.02 in: its two ends 1356 px apart along the rifle for the ledger's 1.718 in (789 px/in; bolt_pin_seat_d's), and places counted from the screw's middle in the same photo (photo 1579.5, 875.5: bolt_pin_x, bolt_pin_y), which puts the ledger's other figures of the bolt on their edges here within 0.012 in (its front end at photo 1727 for 1722, the dark bar's rear at 1093 for 1102)","method":"the archs top at row 1042 on columns 1400 to 1440 (the slots upper edge is at rows 1091 to 1093, 0.913 by the same frame, for extractor_top_ys 0.924). ± is 5 px","via":"user"}}],"note":"Just under the line where the face ends (bolt_flat_bottom_y): the arch stays inside the lower band."},"extractor_notch_r":{"label":"Bolt: the half-round cut over the extractor, its radius","kind":"length","measurements":[{"id":"user","value":0.07,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/nordic-22rb-upper 26b2fef5a5a3 (the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05)","scaleRef":"the port's own opening in the same photo, in the flat's plane within 0.02 in: its two ends 1356 px apart along the rifle for the ledger's 1.718 in (789 px/in; bolt_pin_seat_d's), and places counted from the screw's middle in the same photo (photo 1579.5, 875.5: bolt_pin_x, bolt_pin_y), which puts the ledger's other figures of the bolt on their edges here within 0.012 in (its front end at photo 1727 for 1722, the dark bar's rear at 1093 for 1102)","method":"half its width where it opens into the slot (columns 1352 to 1470 at row 1088: 59 px, 0.075) and its height above the slots upper edge (rows 1042 to 1092: 50 px, 0.063); a round of 0.07 between the two. ± covers both","via":"user"}}],"note":"Drawn as a round of this radius whose top is at extractor_notch_top_y."},"extractor_pivot_rear_x":{"label":"Extractor: its raised rear end under the half-round cut, rear, X","kind":"length","measurements":[{"id":"user","value":4.748,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/nordic-22rb-upper 26b2fef5a5a3 (the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05)","scaleRef":"the port's own opening in the same photo, in the flat's plane within 0.02 in: its two ends 1356 px apart along the rifle for the ledger's 1.718 in (789 px/in; bolt_pin_seat_d's), and places counted from the screw's middle in the same photo (photo 1579.5, 875.5: bolt_pin_x, bolt_pin_y), which puts the ledger's other figures of the bolt on their edges here within 0.012 in (its front end at photo 1727 for 1722, the dark bar's rear at 1093 for 1102)","method":"along row 1105 the hump is light from column 1381 to 1476; its top is at rows 1087 to 1090, the slots upper edge. ± is 6 px","via":"user"}}],"note":"The extractors rear end stands up into the cut over it, its top lit: a rounded hump as wide as the cut, with the bar running forward from it to extractor_front_x. Ahead of the bar the slot is empty to the bolts front end."},"extractor_pivot_front_x":{"label":"Extractor: its raised rear end under the half-round cut, front, X","kind":"length","measurements":[{"id":"user","value":4.869,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/nordic-22rb-upper 26b2fef5a5a3 (the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05)","scaleRef":"the port's own opening in the same photo, in the flat's plane within 0.02 in: its two ends 1356 px apart along the rifle for the ledger's 1.718 in (789 px/in; bolt_pin_seat_d's), and places counted from the screw's middle in the same photo (photo 1579.5, 875.5: bolt_pin_x, bolt_pin_y), which puts the ledger's other figures of the bolt on their edges here within 0.012 in (its front end at photo 1727 for 1722, the dark bar's rear at 1093 for 1102)","method":"as extractor_pivot_rear_x: column 1476. The bars front end is at column 1517 along row 1125 (4.921, for extractor_front_xs 4.936)","via":"user"}}],"note":"As extractor_pivot_rear_x."},"extractor_spring_front_x":{"label":"Extractors spring: its front end, X","kind":"length","measurements":[{"id":"user","value":4.554,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/nordic-22rb-upper 26b2fef5a5a3 (the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05)","scaleRef":"the port's own opening in the same photo, in the flat's plane within 0.02 in: its two ends 1356 px apart along the rifle for the ledger's 1.718 in (789 px/in; bolt_pin_seat_d's), and places counted from the screw's middle in the same photo (photo 1579.5, 875.5: bolt_pin_x, bolt_pin_y), which puts the ledger's other figures of the bolt on their edges here within 0.012 in (its front end at photo 1727 for 1722, the dark bar's rear at 1093 for 1102)","method":"the coils glints along rows 1110 to 1134 run from column 1100 to 1228; ahead of that one even bar. ± is 8 px","via":"user"}}],"note":"A coil spring lies in the slot behind the extractor, from the slots rear end (extractor_rear_x) forward, and a thin rod runs from it to the extractors raised end."},"extractor_spring_d":{"label":"Extractors spring: its outside diameter","kind":"length","measurements":[{"id":"user","value":0.04,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/nordic-22rb-upper 26b2fef5a5a3 (the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05)","scaleRef":"the port's own opening in the same photo, in the flat's plane within 0.02 in: its two ends 1356 px apart along the rifle for the ledger's 1.718 in (789 px/in; bolt_pin_seat_d's), and places counted from the screw's middle in the same photo (photo 1579.5, 875.5: bolt_pin_x, bolt_pin_y), which puts the ledger's other figures of the bolt on their edges here within 0.012 in (its front end at photo 1727 for 1722, the dark bar's rear at 1093 for 1102)","method":"down columns 1120 and 1160 the coils are lit from row 1108 to 1138: 30 px. ± is 8 px","via":"user"}}],"note":"The wires size isnt read: drawn at a third of the pitch."},"extractor_spring_pitch":{"label":"Extractors spring: from one coil to the next","kind":"length","measurements":[{"id":"user","value":0.037,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/nordic-22rb-upper 26b2fef5a5a3 (the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05)","scaleRef":"the port's own opening in the same photo, in the flat's plane within 0.02 in: its two ends 1356 px apart along the rifle for the ledger's 1.718 in (789 px/in; bolt_pin_seat_d's), and places counted from the screw's middle in the same photo (photo 1579.5, 875.5: bolt_pin_x, bolt_pin_y), which puts the ledger's other figures of the bolt on their edges here within 0.012 in (its front end at photo 1727 for 1722, the dark bar's rear at 1093 for 1102)","method":"along rows 1122 to 1134 the coils glints are at columns 1130, 1160, 1190, 1216 and 1226: 29 px from one to the next. ± is 4 px","via":"user"}}],"note":"Counted on its glints: four and a half coils in its length."},"extractor_rod_d":{"label":"Extractors spring: the rod from it to the extractor, diameter","kind":"length","measurements":[{"id":"user","value":0.019,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/nordic-22rb-upper 26b2fef5a5a3 (the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05)","scaleRef":"the port's own opening in the same photo, in the flat's plane within 0.02 in: its two ends 1356 px apart along the rifle for the ledger's 1.718 in (789 px/in; bolt_pin_seat_d's), and places counted from the screw's middle in the same photo (photo 1579.5, 875.5: bolt_pin_x, bolt_pin_y), which puts the ledger's other figures of the bolt on their edges here within 0.012 in (its front end at photo 1727 for 1722, the dark bar's rear at 1093 for 1102)","method":"down columns 1280 and 1340 one lighter band about row 1128, 15 px tall. ± is 5 px","via":"user"}}],"note":"An even bar a little under the slots middle."},"extractor_rear_x":{"label":"Extractor (the dark bar along the bolt's side at the bore's height): its rear end, X","kind":"length","measurements":[{"id":"user","value":4.395,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/nordic-22rb-upper e421a9af0aa7 (the user's own 22RB, the receiver's right side from close, the ejection port near the frame's middle; 2026-10-03)","scaleRef":"the port's own pocket in the same photo: its two ends 347.7 px apart along the rifle for the ledger's 1.797 in (ejection_port_pocket_rear_x to ejection_port_pocket_front_x: 193.5 px/in on the receiver's side face) and its lower edge for the height (ejection_port_pocket_bottom_y); the photo lies 2.7 degrees off level, by the pocket's edges and the bolt's own","method":"the dark bar let into the round body under the flat: dark from photo x 1384 on rows 1144 to 1150 (4.381 at the side face's scale). Read at the side face's scale and carried to the bolt's face, which stands further from the lens by an amount no photo on file gives: between the pocket's floor (0.23 in in) and 0.45 in. The lens was 12.7 in off the side face (the lug holes read 184 px/in, 0.655 in behind it) and over a point 0.6 in behind the port's middle and 0.7 above it (the frame's middle), so what is on the bolt reads 2 to 4% near that point: the figure has 0.34 in of depth allowed for (0.015 here). ± as bolt_flat_bottom_y's","via":"user"}}],"note":"A bar of darker steel lying along the bolt's right side, centred on the bore's axis within the reading (0.882 against 0.8775); its rear half is ribbed like a spring's coils and a half-round is cut in the bolt above its front half (about 0.075 in radius, centred 4.8 ahead of the pin): both drawn since 2026-10-12 from the square photo (extractor_spring_*, extractor_notch_*), where the bar is a slot with a spring, a rod and the extractor in it, empty ahead of the extractor to the bolt's front end. The review calls it the extractor; no document on file names it."},"extractor_front_x":{"label":"Extractor: its front end, X","kind":"length","measurements":[{"id":"user","value":4.936,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/nordic-22rb-upper e421a9af0aa7 (the user's own 22RB, the receiver's right side from close, the ejection port near the frame's middle; 2026-10-03)","scaleRef":"the port's own pocket in the same photo: its two ends 347.7 px apart along the rifle for the ledger's 1.797 in (ejection_port_pocket_rear_x to ejection_port_pocket_front_x: 193.5 px/in on the receiver's side face) and its lower edge for the height (ejection_port_pocket_bottom_y); the photo lies 2.7 degrees off level, by the pocket's edges and the bolt's own","method":"dark to photo x 1486 on rows 1147 to 1153 (4.907 at the side face's scale). Read at the side face's scale and carried to the bolt's face, which stands further from the lens by an amount no photo on file gives: between the pocket's floor (0.23 in in) and 0.45 in. The lens was 12.7 in off the side face (the lug holes read 184 px/in, 0.655 in behind it) and over a point 0.6 in behind the port's middle and 0.7 above it (the frame's middle), so what is on the bolt reads 2 to 4% near that point: the figure has 0.34 in of depth allowed for (0.029 here). ± as bolt_front_x's","via":"user"}}]},"extractor_top_y":{"label":"Extractor: its upper edge, Y","kind":"length","measurements":[{"id":"user","value":0.924,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/nordic-22rb-upper e421a9af0aa7 (the user's own 22RB, the receiver's right side from close, the ejection port near the frame's middle; 2026-10-03)","scaleRef":"the port's own pocket in the same photo: its two ends 347.7 px apart along the rifle for the ledger's 1.797 in (ejection_port_pocket_rear_x to ejection_port_pocket_front_x: 193.5 px/in on the receiver's side face) and its lower edge for the height (ejection_port_pocket_bottom_y); the photo lies 2.7 degrees off level, by the pocket's edges and the bolt's own","method":"its upper edge at photo x 1390 to 1445: row 1143 (0.948 at the side face's scale). Read at the side face's scale and carried to the bolt's face, which stands further from the lens by an amount no photo on file gives: between the pocket's floor (0.23 in in) and 0.45 in. The lens was 12.7 in off the side face (the lug holes read 184 px/in, 0.655 in behind it) and over a point 0.6 in behind the port's middle and 0.7 above it (the frame's middle), so what is on the bolt reads 2 to 4% near that point: the figure has 0.34 in of depth allowed for (0.024 here). ± as bolt_flat_bottom_y's","via":"user"}}]},"extractor_bottom_y":{"label":"Extractor: its lower edge, Y","kind":"length","measurements":[{"id":"user","value":0.84,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/nordic-22rb-upper e421a9af0aa7 (the user's own 22RB, the receiver's right side from close, the ejection port near the frame's middle; 2026-10-03)","scaleRef":"the port's own pocket in the same photo: its two ends 347.7 px apart along the rifle for the ledger's 1.797 in (ejection_port_pocket_rear_x to ejection_port_pocket_front_x: 193.5 px/in on the receiver's side face) and its lower edge for the height (ejection_port_pocket_bottom_y); the photo lies 2.7 degrees off level, by the pocket's edges and the bolt's own","method":"its lower edge against the dark under it, on a four times enlargement: row 1159 ± 3 (0.866 at the side face's scale). Read at the side face's scale and carried to the bolt's face, which stands further from the lens by an amount no photo on file gives: between the pocket's floor (0.23 in in) and 0.45 in. The lens was 12.7 in off the side face (the lug holes read 184 px/in, 0.655 in behind it) and over a point 0.6 in behind the port's middle and 0.7 above it (the frame's middle), so what is on the bolt reads 2 to 4% near that point: the figure has 0.34 in of depth allowed for (0.026 here). ± is that pick (0.016) and the rest as bolt_flat_bottom_y's","via":"user"},"note":"0.007 above the opening's lower edge on file (ejection_port_bottom_y)."}]},"handguard_clamp_bottom_y":{"label":"Handguard clamp block: its flat underside, Y","kind":"length","measurements":[{"id":"user","value":-0.114,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/nordic-22rb-upper d633f1bf49ff (the user's own 22RB lying on its left side on tile, its right side square on from 5 to 7 ft; 2026-10-03)","scaleRef":"the frame the side outline is traced in (profiles.side): the two lug holes' see-through centres and the rail's first and last slots, 106.9 px/in, 1.2 px rms over the four; the block is astride the centre plane the frame lies in","method":"the silhouette's lower edge (the first sample darker than 70 up a column, 0.002 in steps) at fourteen columns from x 7.10 to 7.95: -0.104 to -0.118, mean -0.113; the four columns over the tile's grout line (7.55 to 7.75, -0.120 to -0.132) left out. Nordic's left view (2b348f6a5149), taken from about 20 degrees above, has the block's near lower edge 21 px under the handguard's (0.25 in at the rail's 83.8 px/in), which is this drop seen past a block 1.06 wide","via":"user"}}],"note":"The block under the rear end of the handguard that its two clamp screws cross. It hangs 0.19 in under the handguard (handguard_bottom_y; the same photo has that edge at 0.070)."},"handguard_clamp_flat_rear_x":{"label":"Handguard clamp block: where its flat underside begins, X","kind":"length","measurements":[{"id":"user","value":7.05,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/nordic-22rb-upper d633f1bf49ff (the user's own 22RB, right side, square on from 5 to 7 ft; 2026-10-03); 0dfba70ae389 (the same upper from below, close; 2026-10-05)","scaleRef":"from the side, the pin frame of profiles.side (106.9 px/in); from below, the bottom face's own M-LOK slots: their rear ends 269 px apart for the standard's 40 mm (170.7 px/in), the short slot's rear end at column 1797 for 9.227 (mlok_slot_front_x, mlok_rear_slot_length)","method":"from the side the lower edge leaves the flat between x 7.10 (-0.105) and 7.05 (-0.100, then -0.070 at 7.00): 7.07. From below the flat is the lighter face, its rear edge at columns 1422 to 1424 on the rows either side of the slit (960, 1030): 7.03 by the slots, 7.045 with the seam of the same photo (column 1346) put on handguard_rear_x. The block's near face is 0.5 in nearer the lens than the frame's plane in the side view: 0.02 in along the rifle if the lens stood over the middle of the upper, inside the ±","via":"user"}}]},"handguard_clamp_flat_front_x":{"label":"Handguard clamp block: where its flat underside ends, X","kind":"length","measurements":[{"id":"user","value":7.955,"unit":"in","pm":0.035,"source":{"type":"photo","photo":"references/nordic-22rb-upper d633f1bf49ff (the user's own 22RB, right side, square on from 5 to 7 ft; 2026-10-03); 0dfba70ae389 (the same upper from below, close; 2026-10-05)","scaleRef":"as handguard_clamp_flat_rear_x: the pin frame from the side, the bottom face's M-LOK slots from below","method":"from the side the lower edge is on the flat at x 7.95 (-0.115) and off it at 8.00 (-0.080): 7.96. From below the lighter face ends at column 1580 on rows 930, 960 and 1030: 7.944 by the slots (the block 0.19 in nearer a lens about 29 in away, by the handguard's own width in the frame: 2 px), 7.956 with the seam on handguard_rear_x","via":"user"}}]},"handguard_clamp_rear_x":{"label":"Handguard clamp block: where its rear ramp meets the handguard's underside on the centre line, X","kind":"length","measurements":[{"id":"user","value":6.81,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/nordic-22rb-upper d633f1bf49ff (the user's own 22RB, right side, square on from 5 to 7 ft; 2026-10-03)","scaleRef":"the pin frame of profiles.side (106.9 px/in)","method":"the silhouette's lower edge at x 7.05, 7.00, 6.95, 6.90: -0.100, -0.070, -0.040, 0.005: a straight rise of 0.70 in per in, which is at the underside's own level in this photo (0.070) at 6.81. Nordic's left view (2b348f6a5149; the seam at column 1303, the rail's pitch 33.0 px: 83.8 px/in) has the outline back on the underside's line at column 1290: 6.75","via":"user"}}],"note":"The ramp from the flat up toward the seam. Behind x 6.90 the edge eases in to the underside (0.025 at 6.85, 0.064 at 6.70): a blend, or the shadow under a part lying on tile, and drawn as neither: the ramp is one plane."},"handguard_clamp_front_x":{"label":"Handguard clamp block: where its front ramp meets the handguard's underside on the centre line, X","kind":"length","measurements":[{"id":"user","value":8.33,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/nordic-22rb-upper d633f1bf49ff (the user's own 22RB, right side, square on from 5 to 7 ft; 2026-10-03)","scaleRef":"the pin frame of profiles.side (106.9 px/in)","method":"the silhouette's lower edge from x 8.00 to 8.35 in steps of 0.05: -0.080, -0.050, -0.015, 0.015, 0.040, 0.050, 0.065, 0.070, and 0.070 to 0.075 from there on: on the underside at 8.33. Nordic's left view (2b348f6a5149, 83.8 px/in from the seam at column 1303) has the outline leave the underside's line at column 1157: 8.34","via":"user"}}]},"handguard_clamp_width":{"label":"Handguard clamp block: its width across the rifle","kind":"length","measurements":[{"id":"user","value":1.06,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/nordic-22rb-upper 0dfba70ae389 (the user's own 22RB from below, close; 2026-10-05); bdb43e3235ed (the same from below, the whole upper; 2026-10-03)","scaleRef":"the bottom face's own M-LOK slots in 0dfba70ae389: their rear ends 269 px apart for the standard's 40 mm (170.7 px/in); the block's face stands 0.19 in nearer a lens about 29 in away (the handguard's 1.602 in reads 266 px at its widest, 0.8 in further), which is 0.7%","method":"the lighter flat's edge up columns 1500, 1530 and 1560: row 899 (and 895 to 907 at 1560), 92.5 px from the slit's middle (rows 985 to 995): 0.538 in a side, 1.077 across; its other edge isn't a step against the diagonal beside it and is taken as the same. bdb43e3235ed has the flat 113 px across where the handguard is 172 (1.602 in): 1.05","via":"user"}}],"note":"Wider than the handguard's bottom flat (0.66): its two side faces stand out of the lower diagonal faces, and meet them where the diagonals are this far apart (handguard_clamp_side_top_y is that line, read in another photo)."},"handguard_clamp_side_top_y":{"label":"Handguard clamp block: the upper edge of its side face, Y","kind":"length","measurements":[{"id":"user","value":0.283,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/nordic-22rb-upper d633f1bf49ff (the user's own 22RB, right side, square on from 5 to 7 ft; 2026-10-03)","scaleRef":"the pin frame of profiles.side (106.9 px/in)","method":"the block's side face is lit (level 35 to 50) between the dark lower diagonal above it and the tile: its upper edge up thirteen columns from x 6.90 to 8.20, 0.275 to 0.295","via":"user"}}],"note":"Where the block's side face meets the handguard's lower diagonal face. Not built from: the script draws the side faces at handguard_clamp_width and checks that they meet the diagonals at this height."},"handguard_clamp_side_rear_x":{"label":"Handguard clamp block: its side face's upper rear corner, X","kind":"length","measurements":[{"id":"user","value":6.85,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/nordic-22rb-upper d633f1bf49ff (the user's own 22RB, right side, square on from 5 to 7 ft; 2026-10-03)","scaleRef":"the pin frame of profiles.side (106.9 px/in)","method":"the lit side face's rear edge: its lower end at 0.270, 0.240, 0.195, 0.155, 0.120, 0.050 up columns 6.85 to 7.10: a line from the face's upper edge at 6.85 down to the flat at 7.29 (0.88 in per in)","via":"user"}}]},"handguard_clamp_side_front_x":{"label":"Handguard clamp block: its side face's upper front corner, X","kind":"length","measurements":[{"id":"user","value":8.23,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/nordic-22rb-upper d633f1bf49ff (the user's own 22RB, right side, square on from 5 to 7 ft; 2026-10-03)","scaleRef":"the pin frame of profiles.side (106.9 px/in)","method":"the lit side face's front edge: its lower end at 0.105, 0.150, 0.180, 0.220 up columns 8.05 to 8.20, and no lit face at 8.25: a line from the face's upper edge at 8.23 down to the flat at 7.77 (0.77 in per in)","via":"user"}}]},"handguard_clamp_corner_rear":{"label":"Handguard clamp block: how far its flat's two rear corners are cut back","kind":"length","measurements":[{"id":"user","value":0.24,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/nordic-22rb-upper d633f1bf49ff (the user's own 22RB, right side; 2026-10-03); 0dfba70ae389 (the same from below, close; 2026-10-05)","scaleRef":"the pin frame from the side (106.9 px/in); the bottom face's M-LOK slots from below (170.7 px/in)","method":"from the side, the side face's rear edge comes down to the flat at 7.29, 0.24 ahead of handguard_clamp_flat_rear_x. From below, the flat's rear edge is 8 px further forward on row 930 (0.17 in inside the side) and 22 px on row 1060 (0.13 inside) than on the middle rows: 0.22 and 0.26 for a cut at 45 degrees","via":"user"}}],"note":"From below the flat's corners are cut off; from the side the cut is the edge the side face ends on. Drawn as a facet from the flat's cut corner up to the side face's upper corner."},"handguard_clamp_corner_front":{"label":"Handguard clamp block: how far its flat's two front corners are cut back","kind":"length","measurements":[{"id":"user","value":0.17,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/nordic-22rb-upper d633f1bf49ff (the user's own 22RB, right side; 2026-10-03); 0dfba70ae389 (the same from below, close; 2026-10-05)","scaleRef":"the pin frame from the side (106.9 px/in); the bottom face's M-LOK slots from below (170.7 px/in)","method":"from the side, the side face's front edge comes down to the flat at 7.77, 0.185 behind handguard_clamp_flat_front_x. From below, the flat's front edge is 7 px short on row 1060 (0.13 in inside the side) and whole on row 930 (0.17 inside): 0.17, and under 0.17","via":"user"}}]},"handguard_clamp_slit_width":{"label":"Handguard clamp: the slit along the underside, across","kind":"length","measurements":[{"id":"user","value":0.059,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/nordic-22rb-upper 0dfba70ae389 (the user's own 22RB from below, close; 2026-10-05)","scaleRef":"the bottom face's own M-LOK slots: 170.7 px/in","method":"its two edges up columns 1470 to 1560: rows 984 to 985 and 994 to 995, 10 px; at half its depth of tone 9 to 11 rows at columns 1450, 1500, 1550, 1620","via":"user"}}],"note":"The handguard is slit along the middle of its underside, from the seam through the block, so that the two screws can close it. Black in every photo: what is behind it isn't seen."},"handguard_clamp_slit_front_x":{"label":"Handguard clamp: where the slit ends, X","kind":"length","measurements":[{"id":"user","value":8.4,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/nordic-22rb-upper 0dfba70ae389 (the user's own 22RB from below, close; 2026-10-05)","scaleRef":"the bottom face's own M-LOK slots: 170.7 px/in, the short slot's rear end at column 1797 for 9.227","method":"the slit's own rows (983 to 991) are dark (7 to 28) to column 1650 and the face's tone (49) from 1660: it ends at 1655, 8.395. Behind the block (rows 994 to 1002, columns 1330 to 1430) it is dark to the seam at 1346","via":"user"}}]},"handguard_clamp_screws":{"label":"Handguard clamp: its cross screws","kind":"count","measurements":[{"id":"user","value":2,"unit":"count","source":{"type":"photo","photo":"references/nordic-22rb-upper d633f1bf49ff, e421a9af0aa7 (the user's own 22RB, right side: two socket heads in counterbores); 584c3ded24e1 (its left side: two tapped holes)","scaleRef":"none: a count","method":"counted: two heads on the block's right face, two threaded holes on its left, in the user's photos and in Nordic's (24d592636074, 2b348f6a5149)","via":"user"}}]},"handguard_clamp_screw_rear_x":{"label":"Handguard clamp: the rear screw's axis, X","kind":"length","measurements":[{"id":"user","value":7.3,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/nordic-22rb-upper d633f1bf49ff (the user's own 22RB, right side, square on from 5 to 7 ft; 2026-10-03)","scaleRef":"the pin frame of profiles.side (106.9 px/in)","method":"the dark ring round the head (its counterbore's shadow) fitted as a circle on a 0.005 in grid of centres and radii: centre 7.295, 0.105. The head is 0.5 in nearer the lens than the frame's plane: up to 0.02 in further forward if the lens stood over the middle of the upper, inside the ±. Nordic's left view (2b348f6a5149, 83.8 px/in from the seam at column 1303) has the tapped hole at column 1244: 7.30","via":"user"}}]},"handguard_clamp_screw_spacing":{"label":"Handguard clamp: from one screw's axis to the other's","kind":"length","measurements":[{"id":"user","value":0.505,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/nordic-22rb-upper d633f1bf49ff (the user's own 22RB, right side, square on from 5 to 7 ft; 2026-10-03)","scaleRef":"the pin frame of profiles.side (106.9 px/in)","method":"the two rings' fitted centres: 7.295 and 7.800. Nordic's left view (2b348f6a5149) has the two holes 41 px apart at 83.8 px/in: 0.49","via":"user"}}]},"handguard_clamp_screw_y":{"label":"Handguard clamp: the screws' axes, Y","kind":"length","measurements":[{"id":"user","value":0.1,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/nordic-22rb-upper d633f1bf49ff (the user's own 22RB, right side, square on from 5 to 7 ft; 2026-10-03)","scaleRef":"the pin frame of profiles.side (106.9 px/in)","method":"the two rings' fitted centres: 0.105 and 0.100","via":"user"}}]},"handguard_clamp_counterbore_d":{"label":"Handguard clamp: the counterbore each screw head sits in, its diameter","kind":"length","measurements":[{"id":"user","value":0.27,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/nordic-22rb-upper d633f1bf49ff (the user's own 22RB, right side, square on from 5 to 7 ft; 2026-10-03)","scaleRef":"the pin frame of profiles.side (106.9 px/in)","method":"the dark ring round each head, fitted: radius 0.135 on both; along the rifle through the rear one, its lit wall at -0.11 and its shadowed wall at +0.145 of the centre","via":"user"}}],"note":"How deep it is, and how far under the face the head stands, no view gives."},"handguard_clamp_screw_head_d":{"label":"Handguard clamp: a screw's head, its diameter","kind":"length","measurements":[{"id":"user","value":0.2,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/nordic-22rb-upper e421a9af0aa7 (the user's own 22RB, the receiver's right side from close; 2026-10-03)","scaleRef":"the counterbore's own ring in the same photo and the same face: 50 px across for handguard_clamp_counterbore_d","method":"the head inside the ring, 36 to 40 px across on both screws (centres 1908, 1327 and 2005, 1333). Within one face of a close photo: a ratio, nothing across planes","via":"user"}}]},"handguard_clamp_screw_socket":{"label":"Handguard clamp: a screw's hex socket, across","kind":"length","measurements":[{"id":"user","value":0.11,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/nordic-22rb-upper e421a9af0aa7 (the user's own 22RB, the receiver's right side from close; 2026-10-03)","scaleRef":"the counterbore's own ring in the same photo and the same face: 50 px across for handguard_clamp_counterbore_d","method":"the socket in each head, 20 to 22 px across","via":"user"}}],"note":"A socket head: the hex is lit inside both heads. How deep it goes isn't seen."},"handguard_clamp_hole_d":{"label":"Handguard clamp: the threaded holes on the block's left face, their diameter","kind":"length","measurements":[{"id":"user","value":0.135,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/nordic-22rb-upper 584c3ded24e1 (the user's own 22RB, close on the seam from the left, the upper upside down in the frame; 2026-10-04)","scaleRef":"the two holes' own spacing in the same photo and the same face: their rear edges 275 px apart along the rifle for handguard_clamp_screw_spacing (545 px/in)","method":"each hole along the rifle on rows 690 and 700: 71 px (columns 1510 to 1581) and 74 (1785 to 1859). Along the rifle only: the face is seen from well above its square","via":"user"}}],"note":"The screws go in from the right and thread into the block's left half: on the left there are two open threaded holes, their threads lit. Taken as on the screws' own axes."},"handguard_panel_length":{"label":"Handguard: the blind panel behind each row of M-LOK slots, its length","kind":"length","measurements":[{"id":"harvest","value":0.93,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/nordic-22rb-upper 2b348f6a5149 (left side, NC22RB-UPPER-16-KIT_3_HR)","scaleRef":"the short slot beside it in the same face: 80 px (columns 1003 to 1083) for mlok_rear_slot_length","method":"the panel's two ends on the side face and on the upper diagonal: columns 1109 and 1189, 80 px, the short slot's own length. (The rail's pitch in the same photo is 33.0 px, 83.8 px/in, which has both 0.955.)","via":"harvest"}}],"note":"Behind the rearmost (short) slot of the rows on the two side faces and the two upper diagonal faces there is a panel of the short slot's own outline that doesn't go through: Nordic's two side views and the user's close one (e421a9af0aa7) have it on those four faces. The three lower faces have the clamp's block there and no room for one (the user's views from below). A side view says where it is and not which way it goes: taken as milled in, as the slots and the grooves are, and its depth isn't read."},"handguard_panel_width":{"label":"Handguard: the blind panel behind each row, across the face","kind":"length","measurements":[{"id":"harvest","value":0.29,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/nordic-22rb-upper 2b348f6a5149 (left side, NC22RB-UPPER-16-KIT_3_HR)","scaleRef":"the slot beside it in the same face: its opening 22 px across (rows 967 to 989 at column 1030) for the standard's 7 mm (std.mlok.slot_width)","method":"the panel's two edges up columns 1130, 1150 and 1170 on the upper diagonal: rows 968 and 991, 23 px. The user's close view of the right side (e421a9af0aa7) has it 57 to 63 px across where the two grooves either side of the row are 87 px apart for twice handguard_groove_offset: 0.275 to 0.30","via":"harvest"}}]},"handguard_panel_gap":{"label":"Handguard: from the blind panel's front end to the rear end of the short slot ahead of it","kind":"length","measurements":[{"id":"harvest","value":0.31,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/nordic-22rb-upper 2b348f6a5149 (left side, NC22RB-UPPER-16-KIT_3_HR)","scaleRef":"the short slot beside it in the same face (80 px for mlok_rear_slot_length: 86 px/in) and the rail's pitch in the same photo (33.0 px: 83.8 px/in)","method":"from the panel's front end (column 1109) to the short slot's rear end (1083): 26 px, 0.30 and 0.31 by the two scales. Nordic's right view (24d592636074) has 16 px of gap beside a panel 50 px long: 0.30. The user's close view (e421a9af0aa7) has 30 px beside a panel 188 long, which would be 0.15: its slot is at the frame's edge, 5 in off the lens's axis from 10 in, and that reading is set aside","via":"harvest"}}],"note":"The web the standard leaves between two slots of a row is 0.315 (std.mlok.slot_pitch less std.mlok.slot_length): the panel stands off the short slot as a slot would."}}},{"subject":"nordic-thread-protector","title":"Nordic Components 1/2-28 thread protector (ships on the 22RB)","dimensions":{"length":{"label":"Length, from the barrel's shoulder (its seam with the barrel) to its face","kind":"length","measurements":[{"id":"left","value":0.47,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/nordic-22rb-upper 2b348f6a5149 (left side, NC22RB-UPPER-16-KIT_3_HR)","scaleRef":"rail model from 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%), anchored at takedown lug (1853.5,1074.5) = frame x 0; 0.0118 in/px at the muzzle","method":"the seam's dark line to the face's silhouette on rows within 0.15 in of the axis (0.458–0.470)","via":"harvest"},"note":"Both ends are read on the near side of the part, at the axis's height, so the photo's perspective moves them alike (40 px between them, row by row)."},{"id":"thread","value":0.511,"unit":"in","pm":0.016,"source":{"type":"derived","expr":"{nordic-22rb-upper.muzzle_thread_length} + {nordic-22rb-upper.muzzle_face_behind_protector}","via":"user"},"note":"A sleeve seated on the barrel's shoulder with the muzzle face flush in its mouth is as long as the threaded end (0.506 on the user's own barrel, bare, by its thread's pitch) and the face's setback. The user's close photo of the muzzle (6d62ff2e1c20) has it 0.50 to 0.52; their far ones 0.48 ± 0.03."}],"adopt":{"from":"thread","reason":"The barrel's threaded end, measured bare on the user's own upper, and the flush face; the product photo's 0.47 ± 0.02 is read across a seam seen at an angle."}},"od":{"label":"OD","kind":"length","measurements":[{"id":"photo","value":0.73,"unit":"in","stated":"about 0.73 in","source":{"type":"photo","photo":"22RB side product photo (not yet archived)","scaleRef":"not recorded in brief","method":"calibrated photo measurement","via":"brief"}},{"id":"harvest-left","value":0.717,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/nordic-22rb-upper 2b348f6a5149 (left side, NC22RB-UPPER-16-KIT_3_HR via Aerospace Arms)","scaleRef":"top-rail Picatinny slots: 49 slots, 83.9 px/in, cubic fit rms 0.001 in","method":"silhouette plateau over the last 1.0 in (thread protector + barrel); cylinder silhouettes are unaffected by camera elevation. ± is 1 px","calibration":"references/nordic-22rb-upper/*-2b348f6a5149.calib.json","via":"harvest"}},{"id":"harvest-right","value":0.711,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/nordic-22rb-upper 24d592636074 (right side, Nordic NC22-16-Upper-V2)","scaleRef":"top-rail Picatinny slots: 37 slots, 50.0 px/in, rms 0.017 in","method":"silhouette plateau over the last 1.0 in","calibration":"references/nordic-22rb-upper/*-24d592636074.calib.json","via":"harvest"}},{"id":"user","value":0.736,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/nordic-22rb-upper 14dc07bfde38, d633f1bf49ff, 8c0c57f466e0, 9c62acf0f248, 7523d9cd1b94 (the user's own 22RB, each side, from 5 to 7 ft, the protector on its muzzle; 2026-10-03)","scaleRef":"the rail's 49 slots and the two lug holes in one fitted camera pose (nordic-22rb-upper.rail_slot0_x#user)","method":"across its silhouette: 0.732, 0.735, 0.737, 0.737, 0.739","via":"user"}}],"adopt":{"from":"user","reason":"The user's own protector in five photos, within 0.007 of each other."}}}},{"subject":"olight-baldr-s-bl","title":"Olight Baldr S BL (black BALDRSBLBK, desert tan)","dimensions":{"weight":{"label":"Weight (say with which batteries, and whether the mount is in it)","kind":"mass","measurements":[{"id":"olight","value":3.35,"unit":"oz","pm":0.005,"stated":"The weight is 3.35oz/95g (Including Battery).","source":{"type":"spec","publisher":"manufacturer","name":"Olight, Baldr S BL Tactical Light - Unique Blue Laser for Target (blog)","url":"https://www.olight.com/blog/baldr-s-bl-tactical-light-unique-blue-laser","retrieved":"2026-11-06","via":"harvest"}},{"id":"blackstone","value":3.35,"unit":"oz","pm":0.005,"stated":"Weight: 3.35 oz","source":{"type":"spec","publisher":"retailer","name":"Blackstone Shooting, Olight Baldr S, 800 Lumens White LED, Blue Laser, Black Anodized (6972378125552)","url":"https://blackstoneshooting.com/olight-baldr-s-800-lumens-white-led-blue-laser-black-anodized","retrieved":"2026-11-06","via":"harvest"}}],"adopt":{"from":"olight","reason":"The maker's figure; the seller's is the same."},"note":"With its built-in battery (\"Built-in 380mAh, 3.7V lithium polymer battery\"), as sold: the slide rail mount and its Glock-sized insert are on the light (Olight: \"comes standard with both Glock and Picatinny-sized rail inserts\"; the box list names the Picatinny adapter apart, so the Glock one is the one fitted). Whether the 95 g is with the mount isn't said; the mount is part of the light as sold."},"length":{"label":"Overall length","kind":"length","measurements":[{"id":"olight","value":2.48,"unit":"in","pm":0.02,"stated":"Length: 2.48in/63mm","source":{"type":"spec","publisher":"manufacturer","name":"Olight, Baldr S BL Tactical Light - Unique Blue Laser for Target (blog)","url":"https://www.olight.com/blog/baldr-s-bl-tactical-light-unique-blue-laser","retrieved":"2026-11-06","via":"harvest"}},{"id":"blackstone","value":2.48,"unit":"in","pm":0.005,"stated":"Length: 2.48\"","source":{"type":"spec","publisher":"retailer","name":"Blackstone Shooting, Olight Baldr S, 800 Lumens White LED, Blue Laser, Black Anodized (6972378125552)","url":"https://blackstoneshooting.com/olight-baldr-s-800-lumens-white-led-blue-laser-black-anodized","retrieved":"2026-11-06","via":"harvest"}}],"adopt":{"from":"olight","reason":"The maker's figure, given in millimetres first: its ± is half a millimetre. The seller's is the same inches."},"note":"Olight's 2.48 in is its 63 mm converted. Which ends it is taken between isn't said: the body's rear face to the head's front face (the slide rail mount is set on the body's top and slides along it, so where it stands isn't in a fixed length)."},"head_diameter":{"label":"Head (bezel) diameter","kind":"length","measurements":[{"id":"side","value":0.846,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/olight-baldr-s-bl f1a41bae1594 (Blackstone: the side view)","scaleRef":"956.7 px/in (profiles.side)","method":"profiles.side: the head's top and bottom edges, 0.552 and 1.398 below the jaws' tops, x 2.18 to 2.33","via":"harvest"}}],"note":"The round head round the light cup (Olight: \"LED white light, blue laser output from the same light cup mouth\": one opening for both, the laser's window a small disc at the top of the reflector in the front view, DLT c8ea1d0e142d). Olight's \"Head Diameter: 1.28in/32.5mm\" is not the head's: it is the light's overall width with the swing arm's knob (the front view, DLT c8ea1d0e142d: 472 px across the knob and the far jaw for 530 px from the jaws' tops to the body's foot, 0.89 of the height, as 32.5 is of 36 mm; the head itself is 340 px across there), and it is kept as `width`. The head's own diameter is read on the side view."},"overall_height":{"label":"Overall height, from the body's foot to the clamp's jaws","kind":"length","measurements":[{"id":"olight","value":1.42,"unit":"in","pm":0.02,"stated":"Body Diameter: 1.42in/36mm","source":{"type":"spec","publisher":"manufacturer","name":"Olight, Baldr S BL Tactical Light - Unique Blue Laser for Target (blog)","url":"https://www.olight.com/blog/baldr-s-bl-tactical-light-unique-blue-laser","retrieved":"2026-11-06","via":"harvest"}},{"id":"blackstone","value":1.4,"unit":"in","pm":0.05,"stated":"Height: 1.4\"","source":{"type":"spec","publisher":"retailer","name":"Blackstone Shooting, Olight Baldr S, 800 Lumens White LED, Blue Laser, Black Anodized (6972378125552)","url":"https://blackstoneshooting.com/olight-baldr-s-800-lumens-white-led-blue-laser-black-anodized","retrieved":"2026-11-06","via":"harvest"}}],"adopt":{"from":"olight","reason":"The maker's figure in millimetres; the seller's is it rounded to a tenth."},"note":"Olight calls it \"Body Diameter\"; Blackstone's page for the same light calls it \"Height: 1.4\"\". It is the whole light's height, from the body's underside (its face away from the rail) to the tops of the clamp's jaws: on the straight side view (Blackstone f1a41bae1594) the outline is 1355 px tall for 2375 px long, 0.571 of its length, as 36 mm is of 63 mm (0.571); the body alone is 0.60 of that."},"width":{"label":"Overall width (with its mount and switch)","kind":"length","measurements":[{"id":"olight","value":1.28,"unit":"in","pm":0.02,"stated":"the Head Diameter: 1.28in/32.5mm","source":{"type":"spec","publisher":"manufacturer","name":"Olight, Baldr S BL Tactical Light - Unique Blue Laser for Target (blog)","url":"https://www.olight.com/blog/baldr-s-bl-tactical-light-unique-blue-laser","retrieved":"2026-11-06","via":"harvest"}},{"id":"blackstone","value":1.28,"unit":"in","pm":0.005,"stated":"Width: 1.28\"","source":{"type":"spec","publisher":"retailer","name":"Blackstone Shooting, Olight Baldr S, 800 Lumens White LED, Blue Laser, Black Anodized (6972378125552)","url":"https://blackstoneshooting.com/olight-baldr-s-800-lumens-white-led-blue-laser-black-anodized","retrieved":"2026-11-06","via":"harvest"}}],"adopt":{"from":"olight","reason":"The maker's figure in millimetres, named by it the head's diameter; the seller's is the same inches, named the width."},"note":"Across the swing arm's knob (on the light's +z side, beside the clamp) and the far jaw: Olight's \"Head Diameter\" and Blackstone's \"Width\" (see head_diameter for why it isn't the head's)."},"clamp_rear_x":{"label":"The clamp's rear end (its near plate's rear face), ahead of the light's rear end","kind":"length","measurements":[{"id":"side","value":1.195,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/olight-baldr-s-bl f1a41bae1594 (Blackstone: the side view, 2500 x 1438)","scaleRef":"olight-baldr-s-bl.length and .overall_height on the outline's extents (956.7 px/in)","method":"profiles.side: the plate's rear face, x 1.193 to 1.207 where it rises from the rear block to the jaws' tops","via":"harvest"}}]},"clamp_front_x":{"label":"The clamp's front end (its near plate's front face), ahead of the light's rear end","kind":"length","measurements":[{"id":"side","value":2.084,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/olight-baldr-s-bl f1a41bae1594 (Blackstone: the side view, 2500 x 1438)","scaleRef":"956.7 px/in (profiles.side)","method":"profiles.side: the plate's front face, x 2.083 to 2.085 from the jaws' tops down to 0.22 in","via":"harvest"}}]},"rail_face_below_jaw_top":{"label":"The rail's face (the channel's floor, where the rail's top bears) below the jaws' tops","kind":"length","measurements":[{"id":"front","value":0.16,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/olight-baldr-s-bl c8ea1d0e142d (DLT Trading: the front view, 1000 x 666)","scaleRef":"olight-baldr-s-bl.width and .overall_height on the outline's extents (372.2 px/in, agreeing within 0.2%: profiles.front)","method":"profiles.front: the mount's top beside each jaw's inner wall, 0.157 to 0.164 below the jaws' tops (0.005 and 0.000)","via":"harvest"}}],"note":"The jaws reach this far past the rail's face: a hair past the standard's lower gauge line (0.154), as a clamp that holds the head under its widest must. The front view is taken from a little above, so a floor seen there reads a little high; the insert's top reads 0.117 in (it stands up into the rail's slot)."},"body_rear_x":{"label":"The body's rear face (behind it the rear switch), ahead of the light's rear end","kind":"length","measurements":[{"id":"side","value":0.338,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/olight-baldr-s-bl f1a41bae1594 (Blackstone: the side view)","scaleRef":"956.7 px/in (profiles.side)","method":"profiles.side: the body's rear edge, x 0.336 to 0.340 between depths 0.65 and 1.35","via":"harvest"}}]},"body_front_x":{"label":"Where the body meets the head, ahead of the light's rear end","kind":"length","measurements":[{"id":"side","value":2.11,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/olight-baldr-s-bl f1a41bae1594 (Blackstone: the side view)","scaleRef":"956.7 px/in (profiles.side)","method":"the body's front corner above the head (x 2.106, depth 0.513) and the line where its flat side ends (u 2060 px)","via":"harvest"}}]},"body_top_below_jaw_top":{"label":"The body's top (the face the slide rail mount sits on) below the jaws' tops","kind":"length","measurements":[{"id":"side","value":0.513,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/olight-baldr-s-bl f1a41bae1594 (Blackstone: the side view)","scaleRef":"956.7 px/in (profiles.side)","method":"profiles.side: the body's top edge ahead of the mount, x 2.106 to 2.13, and behind it at x 0.556 to 0.576","via":"harvest"}}]},"head_axis_below_jaw_top":{"label":"The head's axis below the jaws' tops","kind":"length","measurements":[{"id":"side","value":0.975,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/olight-baldr-s-bl f1a41bae1594 (Blackstone: the side view)","scaleRef":"956.7 px/in (profiles.side)","method":"midway between the head's top and bottom edges on profiles.side (0.552 and 1.398, x 2.18 to 2.33)","via":"harvest"}}]},"axis_above_mount":{"label":"The head's axis above the mounting face (the rail's face)","kind":"length","measurements":[{"id":"derived","value":0.815,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"The head's axis on the side view less the rail's face below the jaws' tops on the front view.","via":"harvest"}}]},"body_width":{"label":"The body's width across","kind":"length","measurements":[{"id":"front","value":1.1,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/olight-baldr-s-bl c8ea1d0e142d (DLT Trading: the front view)","scaleRef":"the body's own height on the side view (0.903 in, depth 0.513 to 1.416)","method":"profiles.front: the body 1.053 across (z 0.030 to 1.083) for 0.864 tall (0.556 to 1.420): 1.219 times its height, at the side view's height. The ± covers the close photo's perspective between the body's front end and the jaws.","via":"harvest"}},{"id":"bottom","value":1.06,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/olight-baldr-s-bl abe200dcde6b (DLT Trading: the light from its foot, the lens down, 1270 x 846)","scaleRef":"the head's diameter (head_diameter, 0.846 in): 250 px across in the same view","method":"the body 313 px across (512 to 825) at mid-length; the view's lengths are foreshortened (its scale along the light runs 237 to 270 px/in from the rear to the head), so the width is scaled by the head's width beside it","via":"harvest"}}],"adopt":{"from":"front","reason":"The front view's reading, with which the knob and the far jaw come to the published overall width (1.28); the view from the foot, scaled by the head beside the body, agrees within the two ±."}},"lens_diameter":{"label":"The lens across (the reflector's opening inside the bezel)","kind":"length","measurements":[{"id":"front","value":0.635,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/olight-baldr-s-bl c8ea1d0e142d (DLT Trading: the front view)","scaleRef":"the head's diameter (head_diameter): its bezel ring 340 px across","method":"the reflector's bright disc 255 px across inside the 340 px ring: 0.75 of the head","via":"harvest"}}]},"laser_window_diameter":{"label":"The laser's window across (a dark disc at the top of the reflector)","kind":"length","measurements":[{"id":"front","value":0.124,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/olight-baldr-s-bl c8ea1d0e142d (DLT Trading: the front view)","scaleRef":"the head's ring 340 px across (head_diameter)","method":"the dark disc at (460, 325) px, 50 px across","via":"harvest"}}]},"laser_window_above_axis":{"label":"The laser's window's centre above the head's axis (toward the rail)","kind":"length","measurements":[{"id":"front","value":0.261,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/olight-baldr-s-bl c8ea1d0e142d (DLT Trading: the front view)","scaleRef":"the head's ring 340 px across (head_diameter)","method":"the disc's centre 105 px above the ring's (470, 430)","via":"harvest"}}]},"jaw_thickness":{"label":"Each jaw's thickness across","kind":"length","measurements":[{"id":"front","value":0.15,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/olight-baldr-s-bl c8ea1d0e142d (DLT Trading: the front view)","scaleRef":"the body's width (body_width) on the same view","method":"profiles.front: the far jaw z 0.056 to 0.199 and the near 0.908 to 1.067 (0.143 and 0.159 in the view's units), times the body's 1.10 over its 1.053","via":"harvest"}}]},"knob_diameter":{"label":"The swing arm's knob across (on the light's +z side)","kind":"length","measurements":[{"id":"front","value":0.29,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/olight-baldr-s-bl c8ea1d0e142d (DLT Trading: the front view)","scaleRef":"body_width on the same view","method":"profiles.front: the knob from 0.199 to 0.478 below the jaws' tops (0.279), times 1.045","via":"harvest"}}]},"knob_proud":{"label":"How far the knob stands out from the mount's side","kind":"length","measurements":[{"id":"front","value":0.205,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/olight-baldr-s-bl c8ea1d0e142d (DLT Trading: the front view)","scaleRef":"body_width on the same view","method":"profiles.front: the knob's outer face at z 1.279 against the mount's side at 1.069 to 1.083, times 1.045","via":"harvest"}}]},"screw_x":{"label":"The clamp's slotted screw (on its -z plate) ahead of the light's rear end","kind":"length","measurements":[{"id":"side","value":1.476,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/olight-baldr-s-bl f1a41bae1594 (Blackstone: the side view)","scaleRef":"956.7 px/in","method":"the screw head's centre at (1450, 355) px; 0.337 in below the jaws' tops","via":"harvest"}}]},"screw_below_jaw_top":{"label":"The slotted screw's centre below the jaws' tops","kind":"length","measurements":[{"id":"side","value":0.337,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/olight-baldr-s-bl f1a41bae1594 (Blackstone: the side view)","scaleRef":"956.7 px/in","method":"the screw head's centre at (1450, 355) px","via":"harvest"}}]},"screw_diameter":{"label":"The slotted screw's head across","kind":"length","measurements":[{"id":"side","value":0.2,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/olight-baldr-s-bl f1a41bae1594 (Blackstone: the side view)","scaleRef":"956.7 px/in","method":"the head 190 px across (1355 to 1545)","via":"harvest"}}]},"adjuster_lr_x":{"label":"The laser's windage screw (L/R) ahead of the light's rear end, on the -z side","kind":"length","measurements":[{"id":"side","value":1.23,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/olight-baldr-s-bl f1a41bae1594 (Blackstone: the side view)","scaleRef":"956.7 px/in","method":"the hole's centre at (1215, 755) px","via":"harvest"}}]},"adjuster_ud_x":{"label":"The laser's elevation screw (U/D) ahead of the light's rear end, on the -z side","kind":"length","measurements":[{"id":"side","value":1.49,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/olight-baldr-s-bl f1a41bae1594 (Blackstone: the side view)","scaleRef":"956.7 px/in","method":"the hole's centre at (1465, 755) px","via":"harvest"}}]},"adjuster_below_jaw_top":{"label":"The two adjusting screws' centres below the jaws' tops","kind":"length","measurements":[{"id":"side","value":0.755,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/olight-baldr-s-bl f1a41bae1594 (Blackstone: the side view)","scaleRef":"956.7 px/in","method":"both holes' centres at v 755 px","via":"harvest"}}]},"adjuster_diameter":{"label":"The adjusting screws' holes across","kind":"length","measurements":[{"id":"side","value":0.125,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/olight-baldr-s-bl f1a41bae1594 (Blackstone: the side view)","scaleRef":"956.7 px/in","method":"each hole's dark ring 120 px across","via":"harvest"}}]},"rear_switch_width":{"label":"The rear switch's ribbed paddle across","kind":"length","measurements":[{"id":"bottom","value":0.935,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"The view from the foot (DLT abe200dcde6b): the paddle 265 px across (535 to 800) of the body's 313 there, 0.85 of the body's width.","via":"harvest"}}]},"contact_x":{"label":"The magnetic charging contact's centre on the foot, ahead of the light's rear end","kind":"length","measurements":[{"id":"bottom","value":1.224,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/olight-baldr-s-bl abe200dcde6b (DLT Trading: the light from its foot)","scaleRef":"the body's rear face and its front end on the foot's outline (245 and 680 px) at body_rear_x and body_front_x","method":"the gold contact's centre at (668, 462) px, 0.499 of the way from the rear face to the head; on the body's middle across (668.5)","via":"harvest"}}]},"contact_diameter":{"label":"The magnetic charging contact (the gold disc) across","kind":"length","measurements":[{"id":"bottom","value":0.19,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/olight-baldr-s-bl abe200dcde6b (DLT Trading: the light from its foot)","scaleRef":"the head's diameter, 250 px across in the same view","method":"the disc 56 px across","via":"harvest"}}]},"contact_ring_diameter":{"label":"The ring round the charging contact across (where the magnetic cable's head sits)","kind":"length","measurements":[{"id":"bottom","value":0.71,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/olight-baldr-s-bl abe200dcde6b (DLT Trading: the light from its foot)","scaleRef":"the head's diameter, 250 px across in the same view","method":"the ring's outer edge 210 px across (563 to 773)","via":"harvest"}}]},"key_height":{"label":"How far the Picatinny insert's cross key stands up from the channel's floor into the rail's slot","kind":"length","measurements":[{"id":"assumed","value":0.04,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the insert's top reads 0.043 above the floor in the front view (0.117 against 0.160 below the jaws' tops), which a view from a little above lifts; under the standard's slot depth (0.118).","via":"harvest"}}]},"lens_recess":{"label":"How far the lens stands behind the bezel's front face","kind":"length","measurements":[{"id":"assumed","value":0.06,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the reflector's depth isn't given; the glass is set back from the bezel's face as the front-left views show it.","via":"harvest"}}]},"adjuster_depth":{"label":"How deep the adjusting screws' holes are drawn","kind":"length","measurements":[{"id":"assumed","value":0.04,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the screws sit inside their holes; how far isn't seen.","via":"harvest"}}]},"lever_rear_x":{"label":"The swing arm's lever (on the +z side, behind the knob) its rear end, ahead of the light's rear end","kind":"length","measurements":[{"id":"side","value":0.577,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/olight-baldr-s-bl f1a41bae1594 (Blackstone: the side view)","scaleRef":"956.7 px/in (profiles.side)","method":"profiles.side: the block's rear face, x 0.575 to 0.580","via":"harvest"}}],"note":"The lever stands behind the mount on the far side of the side view, black, and its silhouette is the side outline's lower block above the body's rear half (u 590 to 1180 px, its top at depth 0.19): AR15Discounts' photograph of the tan light from its +z side (7b0dbbc5cfe8) has the ribbed black lever there, from the knob back, rising to about the jaws' tops."},"lever_top_below_jaw_top":{"label":"The lever's edge toward the rail, below the jaws' tops","kind":"length","measurements":[{"id":"side","value":0.19,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/olight-baldr-s-bl f1a41bae1594 (Blackstone: the side view)","scaleRef":"956.7 px/in (profiles.side)","method":"profiles.side: the block's top edge, 0.171 to 0.214 (x 0.58 to 1.16)","via":"harvest"}}]},"lever_thickness":{"label":"The lever's plate thickness across","kind":"length","measurements":[{"id":"assumed","value":0.06,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view shows the lever square across; in the front view it is inside the knob's 0.205 in out from the mount's side, behind the knob.","via":"harvest"}}]},"contact_ring_groove":{"label":"The ring's groove, across and deep","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the ring reads as a bright line some 6 px wide in the view from the foot (0.02 in), a cut edge catching the light; how deep it goes isn't seen and it is drawn as deep as it is wide.","via":"harvest"}}]}}},{"subject":"otter-creek-polonium-k","title":"Otter Creek Labs Polonium K","dimensions":{"can_length":{"label":"The suppressor alone, without a mount: its rear face to its front face","kind":"length","measurements":[{"id":"capitol","value":4.8,"unit":"in","stated":"4.8\" length without mount","source":{"type":"spec","publisher":"retailer","name":"Capitol Armory, Otter Creek Polonium K (its SKU OCL-POL556K), Features","url":"https://www.capitolarmory.com/otter-creek-labs-polonium-k-556-suppressor.html","retrieved":"2026-10-06","via":"harvest"}},{"id":"silencer-shop","value":4.8,"unit":"in","stated":"It is 4.8 inches long, weighs 11.5 oz without a mount, and measures 1.625 inches in outer diameter.","source":{"type":"spec","publisher":"retailer","name":"Silencer Shop, Otter Creek Labs Polonium K (its SKU OCL-POLK-MULTI)","url":"https://www.silencershop.com/otter-creek-labs-polonium-k.html","retrieved":"2026-10-06","via":"harvest"}},{"id":"silencer-central","value":4.8,"unit":"in","stated":"Length 4.8\"","source":{"type":"spec","publisher":"retailer","name":"Silencer Central, Otter Creek Polonium K, Description and Specs","url":"https://www.silencercentral.com/products/otter-creek-polonium-k","retrieved":"2026-10-06","via":"harvest"}},{"id":"kygunco","value":4.8,"unit":"in","stated":"Length: 4.8\", Weight: 11.5 oz, OD: 1.625\"","source":{"type":"spec","publisher":"retailer","name":"KYGunCo, Otter Creek Labs Black Polonium-K 5.56 Suppressor (MPN POLK, UPC 664533654156)","url":"https://www.kygunco.com/product/otter-creek-labs-polk-polonium-k","retrieved":"2026-10-06","via":"harvest"}},{"id":"bauer","value":4.8,"unit":"in","stated":"Length: 4.8 inches Weight: 11.5 oz (without mount) Outer Diameter: 1.625 inches","source":{"type":"spec","publisher":"retailer","name":"Bauer Precision, Otter Creek Labs Polonium K, black (its SKU PoloniumK, MPN POLK), Specifications","url":"https://www.bauer-precision.com/ocl-polonium-k-5-56-6mm-steel-suppressor-black-finish/","retrieved":"2026-10-06","via":"harvest"}},{"id":"pew-science","value":4.8,"unit":"in","stated":"It has a 1.625-inch diameter and is 4.8 inches in length, without a mount.","source":{"type":"spec","publisher":"review","name":"PEW Science, Sound Signature Review 6.95: Otter Creek Labs Polonium-K on the MK18 (October 2022)","url":"https://pewscience.com/sound-signature-reviews-free/sss-6-95-ocl-polonium-k-mk18-556","retrieved":"2026-10-06","via":"harvest"},"note":"Not said to be measured: the same page says its data is \"published with the express written permission of Otter Creek Labs, LLC\", and the figure is the maker's."},{"id":"photo","value":4.77,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/otter-creek-polonium-k 0817f888c9c7 (Silencer Central's gallery, otter_creek_polonium-k-1.jpg: the K standing on its mount on white, from the side, 1000 x 1000; serial GK0104, the black mount)","scaleRef":"overall_length (5.3, PEW Science's with the mount) between the mount's rear face and the collar's tip: 925 px along the axis, 174.5 px/in","method":"the photo turned muzzle to the right, its silhouette column by column at luminance 200 (.cache/batch46/otter-creek-polonium-k/prof.py): the can's rear face is where its rear chamfer begins, column 112 (the mount's flange, 8 columns thick, behind it), its front face column 944.5: 832.5 px","via":"harvest"},"note":"The proportion of the whole that is the can: at the scale PEW Science's 5.3 gives, the can is 4.77, inside the published 4.8's last digit. The model keeps this proportion."}],"adopt":{"from":"capitol","reason":"Every seller's figure and the reviewer's are the one number. The photo's reading is the can's share of the 5.3 in whole, 0.03 under: within the figure's last digit."},"note":"Otter Creek's figure as six sellers and a reviewer state it, two of the sellers and the reviewer saying \"without mount\". Taken to be between the two faces, not to the tip of the notched collar that stands 0.1 in out of the front face: read that way the photo of the whole thing agrees with PEW Science's 5.3 in with the mount (overall_length), and to the collar's tip it would not."},"overall_length":{"label":"End to end with the 1/2x28 direct thread mount it is sold with in it: the mount's rear face to the tip of the collar on the front face","kind":"length","measurements":[{"id":"pew-science","value":5.3,"unit":"in","stated":"The total length with the included direct thread adapter is 5.3 inches.","source":{"type":"spec","publisher":"review","name":"PEW Science, Sound Signature Review 6.95: Otter Creek Labs Polonium-K on the MK18 (October 2022)","url":"https://pewscience.com/sound-signature-reviews-free/sss-6-95-ocl-polonium-k-mk18-556","retrieved":"2026-10-06","via":"harvest"}},{"id":"photo","value":5.33,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/otter-creek-polonium-k 0817f888c9c7 (Silencer Central's gallery, otter_creek_polonium-k-1.jpg: the K standing on its mount on white, from the side, 1000 x 1000; serial GK0104, the black mount)","scaleRef":"can_length (4.8, the sellers' without a mount) between the can's two faces: 832.5 px along the axis, 173.4 px/in","method":"the mount's rear face to the collar's tip, 925 px: the rear face is 6 columns inside the silhouette's tip (column 30), where the arc of its rim meets the hex's chamfer (the lens stood opposite the front grooves, about 34 in off, and sees the rear end from 8 degrees off square: the flange's rim, a circle 1.49 in across, sags 16 px); the collar's tip is column 961","via":"harvest"},"note":"The same photo read the other way round: by the can's published length the whole is 5.33. The ± is two pixels at each end and the can's own last digit left out."}],"adopt":{"from":"pew-science","reason":"The one page that states the length as sold, with the mount; the photo, scaled by the sellers' length without it, reads 0.03 more, inside its last digit."},"note":"What the model is held to. One page states it. Its two ends are taken to be the extremes: the hex's rear face and the notched collar's tip."},"length":{"label":"Length ahead of the barrel's shoulder, installed (to the front face)","kind":"length","measurements":[{"id":"shouldered","value":5.3,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{.overall_length}","via":"harvest"}}],"note":"The whole of it: the mount's rear face (the hex's, with the 1/2x28 thread's mouth in it, the rearmost face in every photo) is taken to bear on the barrel's shoulder. No page on file says what bears on what, or what barrel thread the mount takes."},"od":{"label":"Largest outside diameter","kind":"length","measurements":[{"id":"capitol","value":1.625,"unit":"in","stated":"1.625\" diameter","source":{"type":"spec","publisher":"retailer","name":"Capitol Armory, Otter Creek Polonium K (its SKU OCL-POL556K), Features","url":"https://www.capitolarmory.com/otter-creek-labs-polonium-k-556-suppressor.html","retrieved":"2026-10-06","via":"harvest"}},{"id":"silencer-shop","value":1.625,"unit":"in","stated":"Outer diameter: 1.625 inches","source":{"type":"spec","publisher":"retailer","name":"Silencer Shop, Otter Creek Labs Polonium K (its SKU OCL-POLK-MULTI)","url":"https://www.silencershop.com/otter-creek-labs-polonium-k.html","retrieved":"2026-10-06","via":"harvest"}},{"id":"silencer-central","value":1.625,"unit":"in","stated":"Diameter 1.625\"","source":{"type":"spec","publisher":"retailer","name":"Silencer Central, Otter Creek Polonium K, Description and Specs","url":"https://www.silencercentral.com/products/otter-creek-polonium-k","retrieved":"2026-10-06","via":"harvest"}},{"id":"kygunco","value":1.625,"unit":"in","stated":"Length: 4.8\", Weight: 11.5 oz, OD: 1.625\"","source":{"type":"spec","publisher":"retailer","name":"KYGunCo, Otter Creek Labs Black Polonium-K 5.56 Suppressor (MPN POLK, UPC 664533654156)","url":"https://www.kygunco.com/product/otter-creek-labs-polk-polonium-k","retrieved":"2026-10-06","via":"harvest"}},{"id":"bauer","value":1.625,"unit":"in","stated":"Outer Diameter: 1.625 inches","source":{"type":"spec","publisher":"retailer","name":"Bauer Precision, Otter Creek Labs Polonium K, black (its SKU PoloniumK, MPN POLK), Specifications","url":"https://www.bauer-precision.com/ocl-polonium-k-5-56-6mm-steel-suppressor-black-finish/","retrieved":"2026-10-06","via":"harvest"}},{"id":"pew-science","value":1.625,"unit":"in","stated":"It has a 1.625-inch diameter and is 4.8 inches in length, without a mount.","source":{"type":"spec","publisher":"review","name":"PEW Science, Sound Signature Review 6.95: Otter Creek Labs Polonium-K on the MK18 (October 2022)","url":"https://pewscience.com/sound-signature-reviews-free/sss-6-95-ocl-polonium-k-mk18-556","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"capitol","reason":"One figure on every page."},"note":"The same in every seller's words. In the photos the front cap and the ring behind it are the widest; the body behind the grooves reads 0.003 to 0.009 in under them across (three sections of the weldment, each a pixel wider than the one behind it in Silencer Central's photo and not in Capitol Armory's), which the model doesn't draw."},"od_in_photo":{"label":"The largest diameter as the side photo reads it at the length's scale (a check, not drawn)","kind":"length","measurements":[{"id":"photo","value":1.57,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/otter-creek-polonium-k 0817f888c9c7 (Silencer Central's gallery, otter_creek_polonium-k-1.jpg: the K standing on its mount on white, from the side, 1000 x 1000; serial GK0104, the black mount)","scaleRef":"overall_length (5.3) between the mount's rear face and the collar's tip: 925 px, 174.5 px/in","method":"the front cap between its two edges at luminance 200: 274.0 px (273.0 to 274.0 over columns 913 to 940); at luminance 240 a pixel more","via":"harvest"}}],"note":"A black tube reads thin on white: at the scale the published length gives, the published 1.625 reads 1.57, 3.4% under. The model's lengths are at the length's scale and its diameters at the diameter's (the front cap's width taken as od), as the catalog's barrels are; the other possibility, that this can is 1.57 across or 5.5 long, isn't one any page supports. Capitol Armory's photo of another unit, lying on white, has its top edge 0.5% nearer its length's scale, its underside in shadow."},"can_weight":{"label":"Weight of the suppressor alone, without a mount","kind":"mass","measurements":[{"id":"capitol","value":11.5,"unit":"oz","stated":"11.5 oz without mount","source":{"type":"spec","publisher":"retailer","name":"Capitol Armory, Otter Creek Polonium K (its SKU OCL-POL556K), Features","url":"https://www.capitolarmory.com/otter-creek-labs-polonium-k-556-suppressor.html","retrieved":"2026-10-06","via":"harvest"}},{"id":"silencer-shop","value":11.5,"unit":"oz","stated":"Weight: 11.5 oz (without mount)","source":{"type":"spec","publisher":"retailer","name":"Silencer Shop, Otter Creek Labs Polonium K (its SKU OCL-POLK-MULTI)","url":"https://www.silencershop.com/otter-creek-labs-polonium-k.html","retrieved":"2026-10-06","via":"harvest"}},{"id":"silencer-central","value":11.5,"unit":"oz","stated":"Weight 11.5 oz","source":{"type":"spec","publisher":"retailer","name":"Silencer Central, Otter Creek Polonium K, Description and Specs","url":"https://www.silencercentral.com/products/otter-creek-polonium-k","retrieved":"2026-10-06","via":"harvest"}},{"id":"kygunco","value":11.5,"unit":"oz","stated":"Length: 4.8\", Weight: 11.5 oz, OD: 1.625\"","source":{"type":"spec","publisher":"retailer","name":"KYGunCo, Otter Creek Labs Black Polonium-K 5.56 Suppressor (MPN POLK, UPC 664533654156)","url":"https://www.kygunco.com/product/otter-creek-labs-polk-polonium-k","retrieved":"2026-10-06","via":"harvest"}},{"id":"bauer","value":11.5,"unit":"oz","stated":"Weight: 11.5 oz (without mount)","source":{"type":"spec","publisher":"retailer","name":"Bauer Precision, Otter Creek Labs Polonium K, black (its SKU PoloniumK, MPN POLK), Specifications","url":"https://www.bauer-precision.com/ocl-polonium-k-5-56-6mm-steel-suppressor-black-finish/","retrieved":"2026-10-06","via":"harvest"}},{"id":"pew-science","value":11.5,"unit":"oz","stated":"As tested, the silencer weighs 11.5 ounces and the direct-thread mount weighs weighs 2.1 ounces, for a total system weight of 13.6 ounces.","source":{"type":"spec","publisher":"review","name":"PEW Science, Sound Signature Review 6.95: Otter Creek Labs Polonium-K on the MK18 (October 2022)","url":"https://pewscience.com/sound-signature-reviews-free/sss-6-95-ocl-polonium-k-mk18-556","retrieved":"2026-10-06","via":"harvest"},"note":"\"As tested\": the one figure said of the unit in hand (the doubled word is the page's)."}],"adopt":{"from":"pew-science","reason":"The reviewer's as-tested weight; every seller's figure is the same."}},"mount_weight":{"label":"Weight of the 1/2x28 direct thread mount it is sold with","kind":"mass","measurements":[{"id":"pew-science","value":2.1,"unit":"oz","stated":"As tested, the silencer weighs 11.5 ounces and the direct-thread mount weighs weighs 2.1 ounces, for a total system weight of 13.6 ounces.","source":{"type":"spec","publisher":"review","name":"PEW Science, Sound Signature Review 6.95: Otter Creek Labs Polonium-K on the MK18 (October 2022)","url":"https://pewscience.com/sound-signature-reviews-free/sss-6-95-ocl-polonium-k-mk18-556","retrieved":"2026-10-06","via":"harvest"}}]},"weight":{"label":"Weight as sold, with the direct thread mount in it","kind":"mass","measurements":[{"id":"pew-science","value":13.6,"unit":"oz","stated":"As tested, the silencer weighs 11.5 ounces and the direct-thread mount weighs weighs 2.1 ounces, for a total system weight of 13.6 ounces.","source":{"type":"spec","publisher":"review","name":"PEW Science, Sound Signature Review 6.95: Otter Creek Labs Polonium-K on the MK18 (October 2022)","url":"https://pewscience.com/sound-signature-reviews-free/sss-6-95-ocl-polonium-k-mk18-556","retrieved":"2026-10-06","via":"harvest"}},{"id":"sum","value":13.6,"unit":"oz","pm":0.07,"source":{"type":"derived","expr":"{.can_weight} + {.mount_weight}","via":"harvest"}}],"adopt":{"from":"pew-science","reason":"The reviewer's total for the suppressor as tested with its mount; the sellers' 11.5 oz without a mount and the mount's own 2.1 come to the same."},"note":"The part's weight. KYGunCo's \"Weight 2 lb\" is its parcel's."},"thread_length":{"label":"Barrel thread length it takes, or is made for","kind":"length","measurements":[],"note":"No page on file says what length of 1/2x28 barrel thread the mount takes or is made for, and no manual of Otter Creek's is hosted anywhere the harvester may read. The mount is threaded through (mount_plug_length says how long it is), so the catalog's barrels' threaded ends, half an inch to .63, are inside it as drawn."},"thread_pitch":{"label":"The mount's thread, its pitch","kind":"length","measurements":[{"id":"sellers","value":0.03571,"unit":"in","pm":0.00005,"stated":"a 1/2x28 direct thread mount is included","source":{"type":"spec","publisher":"retailer","name":"Capitol Armory, Otter Creek Polonium K (its SKU OCL-POL556K), Features","url":"https://www.capitolarmory.com/otter-creek-labs-polonium-k-556-suppressor.html","retrieved":"2026-10-06","via":"harvest"},"note":"An inch over 28."}],"note":"28 to the inch by every seller's \"1/2x28\"; the figure is the Army barrel's drawing's, through the catalog's barrel that states it."},"thread_major_d":{"label":"The barrel thread the mount takes, its major diameter (the crests the mount's grooves are drawn a gap outside)","kind":"length","measurements":[{"id":"army","value":0.4957,"unit":"in","pm":0.0033,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.thread_major_d}","via":"harvest"},"note":"The Army barrel's 1/2-28 UNEF-2A, drawing 8448549, as the catalog's barrels carry it: the thread the sellers name for the mount. Nothing of the mount's own thread is measured."}]},"thread_minor_d":{"label":"The barrel thread the mount takes, its minor diameter (the roots the mount's lands are drawn a gap outside)","kind":"length","measurements":[{"id":"army","value":0.4551,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.thread_minor_d}","via":"harvest"}}]},"mount_hex_flats":{"label":"The mount's hex, across its flats","kind":"length","measurements":[{"id":"photo","value":0.805,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/otter-creek-polonium-k 0817f888c9c7 (Silencer Central's gallery, otter_creek_polonium-k-1.jpg: the K standing on its mount on white, from the side, 1000 x 1000; serial GK0104, the black mount)","scaleRef":"the front cap's width in the same photo, taken as od (1.625): 274.0 px, 168.6 px/in","method":"the hex stands with a flat to the lens (its middle face is half its height: 77 of 156.8 px), so its height is corner to corner: 156.8 px over columns 50 to 88, 0.930 in, times the cosine of 30 degrees","via":"harvest"},"note":"The ± is two pixels and what a break on the corners would take off."}],"note":"Read on the black mount. Capitol Armory's unit has a bronze-coloured mount of the same form (Silencer Shop: \"OCL states direct thread adapters may vary in appearance from product photos\")."},"mount_hex_end_d":{"label":"The mount's hex, the diameter of its rear face (where the turned chamfer that relieves its corners begins)","kind":"length","measurements":[{"id":"photo","value":0.76,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/otter-creek-polonium-k 0817f888c9c7 (Silencer Central's gallery, otter_creek_polonium-k-1.jpg: the K standing on its mount on white, from the side, 1000 x 1000; serial GK0104, the black mount)","scaleRef":"the front cap's width in the same photo, taken as od (1.625): 274.0 px, 168.6 px/in","method":"the silhouette's rear end, columns 30 to 50: the rear face's rim is a circle seen from 8 degrees off square, about 128 px across, and from it the outline rises to the hex's corners at 45 degrees (14 px along for 14 out)","via":"harvest"},"note":"The chamfer is drawn at 45 degrees from this circle: it takes the corners off and barely touches the flats, as the photos of the black mount show."}]},"mount_hex_length":{"label":"The mount's hex: its rear face to the flange's rear face","kind":"length","measurements":[{"id":"photo","value":0.39,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/otter-creek-polonium-k 0817f888c9c7 (Silencer Central's gallery, otter_creek_polonium-k-1.jpg: the K standing on its mount on white, from the side, 1000 x 1000; serial GK0104, the black mount)","scaleRef":"overall_length (5.3) between the mount's rear face and the collar's tip: 925 px, 174.5 px/in","method":"the hex's rear face at column 36 (overall_length's photo reading says how), the flange's rear face at column 104: where the arc of its rim (251.3 px across, sagging 16 px toward the rear at mid height) meets the silhouette's top and bottom","via":"harvest"}}]},"can_rear_x":{"label":"The can's rear face, ahead of the mount's rear face (the hex and the flange stand behind it)","kind":"length","measurements":[{"id":"photo","value":0.435,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/otter-creek-polonium-k 0817f888c9c7 (Silencer Central's gallery, otter_creek_polonium-k-1.jpg: the K standing on its mount on white, from the side, 1000 x 1000; serial GK0104, the black mount)","scaleRef":"overall_length (5.3) between the mount's rear face and the collar's tip: 925 px, 174.5 px/in","method":"the hex's rear face at column 36; the can's rear face at column 112, where the silhouette's width stops being the flange's 251.3 px and the can's chamfer begins","via":"harvest"}},{"id":"published","value":0.5,"unit":"in","pm":0.1,"source":{"type":"derived","expr":"{.overall_length} - {.can_length}","via":"harvest"},"note":"Two published lengths, each rounded to a tenth, and the collar's 0.1 in at the front end counted in the first and not in the second."}],"adopt":{"from":"photo","reason":"Read on the photo in proportion to the whole; the published lengths' difference is good to a tenth and includes the collar."},"note":"PEW Science's two lengths put it at 0.5 (5.3 less 4.8, each to a tenth); the photo, in proportion, at 0.435. The flange is a disc 0.046 in thick, flush with the can's rear rim."},"rear_rim_d":{"label":"The can's rear rim, where its rear chamfer begins (the mount's flange is flush with it)","kind":"length","measurements":[{"id":"photo","value":1.49,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/otter-creek-polonium-k 0817f888c9c7 (Silencer Central's gallery, otter_creek_polonium-k-1.jpg: the K standing on its mount on white, from the side, 1000 x 1000; serial GK0104, the black mount)","scaleRef":"the front cap's width in the same photo, taken as od (1.625): 274.0 px, 168.6 px/in","method":"the silhouette's width over columns 104 to 112, the flange's edge and the can's rim: 251.3 px","via":"harvest"}}]},"rear_chamfer_x":{"label":"Where the can's rear chamfer reaches its full diameter, ahead of the mount's rear face","kind":"length","measurements":[{"id":"photo","value":0.616,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/otter-creek-polonium-k 0817f888c9c7 (Silencer Central's gallery, otter_creek_polonium-k-1.jpg: the K standing on its mount on white, from the side, 1000 x 1000; serial GK0104, the black mount)","scaleRef":"overall_length (5.3) between the mount's rear face and the collar's tip: 925 px, 174.5 px/in","method":"the silhouette's width rises in a straight line from 251.3 px at column 112 to the body's 271 at column 143.5","via":"harvest"}}],"note":"A cone 0.18 in long that takes 0.06 in off the radius: 18 degrees. Capitol Armory's photo of another unit has it 0.197 long by its top edge."},"front_face_x":{"label":"The front face, ahead of the mount's rear face","kind":"length","measurements":[{"id":"photo","value":5.205,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/otter-creek-polonium-k 0817f888c9c7 (Silencer Central's gallery, otter_creek_polonium-k-1.jpg: the K standing on its mount on white, from the side, 1000 x 1000; serial GK0104, the black mount)","scaleRef":"overall_length (5.3) between the mount's rear face and the collar's tip: 925 px, 174.5 px/in","method":"the front face at column 944.5 (the silhouette is full width to 942 and gone by 947: the cap's front corner is broken by about 0.02 in; the lens stands opposite column 830, so the face's near rim shows 3 px ahead of it); the collar's tip at column 961","via":"harvest"}}]},"front_edge_break":{"label":"The front cap's front corner: the break on it","kind":"length","measurements":[{"id":"photo","value":0.02,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/otter-creek-polonium-k 0817f888c9c7 (Silencer Central's gallery, otter_creek_polonium-k-1.jpg: the K standing on its mount on white, from the side, 1000 x 1000; serial GK0104, the black mount)","scaleRef":"the front cap's width in the same photo, taken as od (1.625): 274.0 px, 168.6 px/in","method":"the silhouette's width falls from 273.5 px at column 938 to 268.2 at 944, the face's own column: a corner taken off over 3 to 4 px each way","via":"harvest"}}]},"collar_height":{"label":"The notched collar round the bore: how far it stands out of the front face","kind":"length","measurements":[{"id":"side","value":0.095,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{.overall_length} - {.front_face_x}","via":"harvest"}}],"note":"Sellers call it the external flash hider (Capitol Armory: \"Integrated internal and external flash hiders\")."},"collar_od":{"label":"The notched collar's outside diameter","kind":"length","measurements":[{"id":"face","value":0.408,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/otter-creek-polonium-k f710b8f8d6e8 (Silencer Central's gallery, otter_creek_polonium-k-2.jpg: the front cap nearly face on, from 12 degrees above its axis, 1000 x 1000)","scaleRef":"the front face from edge to edge across the photo, taken as od (1.625): 472 px, 290.5 px/in","method":"read on a crop of the face enlarged 2.6 times with the photo's own pixel grid over it (.cache/batch46/otter-creek-polonium-k/crop.py), across the photo, where the view is square: the collar 118.5 px across","via":"harvest"}},{"id":"side","value":0.405,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/otter-creek-polonium-k 0817f888c9c7 (Silencer Central's gallery, otter_creek_polonium-k-1.jpg: the K standing on its mount on white, from the side, 1000 x 1000; serial GK0104, the black mount)","scaleRef":"the front cap's width in the same photo, taken as od (1.625): 274.0 px, 168.6 px/in","method":"the collar's two tabs ahead of the front face, a notch between them facing the lens: 68.3 px from the one's outer edge to the other's","via":"harvest"}}],"adopt":{"from":"face","reason":"The view that shows the whole collar; the side view agrees within 0.003."}},"collar_notches":{"label":"Notches in the collar","kind":"count","measurements":[{"id":"face","value":4,"unit":"count","source":{"type":"photo","photo":"references/otter-creek-polonium-k f710b8f8d6e8 (Silencer Central's gallery, otter_creek_polonium-k-2.jpg: the front cap nearly face on, from 12 degrees above its axis, 1000 x 1000)","scaleRef":"the front face from edge to edge across the photo, taken as od (1.625): 472 px, 290.5 px/in","method":"read on a crop of the face enlarged 2.6 times with the photo's own pixel grid over it (.cache/batch46/otter-creek-polonium-k/crop.py), across the photo, where the view is square: the collar 118.5 px across","via":"harvest"}}],"note":"At twelve, three, six and nine with the cross's four arms. The side view shows one facing the lens between two tabs."},"collar_notch_width":{"label":"The collar's notches, their width","kind":"length","measurements":[{"id":"face","value":0.095,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/otter-creek-polonium-k f710b8f8d6e8 (Silencer Central's gallery, otter_creek_polonium-k-2.jpg: the front cap nearly face on, from 12 degrees above its axis, 1000 x 1000)","scaleRef":"the front face from edge to edge across the photo, taken as od (1.625): 472 px, 290.5 px/in","method":"read on a crop of the face enlarged 2.6 times with the photo's own pixel grid over it (.cache/batch46/otter-creek-polonium-k/crop.py), across the photo, where the view is square: the collar 118.5 px across","via":"harvest"},"note":"The notch at twelve: 27.7 px."},{"id":"side","value":0.101,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/otter-creek-polonium-k 0817f888c9c7 (Silencer Central's gallery, otter_creek_polonium-k-1.jpg: the K standing on its mount on white, from the side, 1000 x 1000; serial GK0104, the black mount)","scaleRef":"the front cap's width in the same photo, taken as od (1.625): 274.0 px, 168.6 px/in","method":"the gap between the two tabs, 17 px","via":"harvest"}}],"adopt":{"from":"face","reason":"Read where the notch is seen square; the side view's gap is within its ±."}},"bore_d":{"label":"The hole in the front face (inside the collar)","kind":"length","measurements":[{"id":"face","value":0.287,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/otter-creek-polonium-k f710b8f8d6e8 (Silencer Central's gallery, otter_creek_polonium-k-2.jpg: the front cap nearly face on, from 12 degrees above its axis, 1000 x 1000)","scaleRef":"the front face from edge to edge across the photo, taken as od (1.625): 472 px, 290.5 px/in","method":"read on a crop of the face enlarged 2.6 times with the photo's own pixel grid over it (.cache/batch46/otter-creek-polonium-k/crop.py), across the photo, where the view is square: the collar 118.5 px across","via":"harvest"},"note":"The dark hole, 83.5 px across."}],"note":"Larger than the sellers' \"6mm bore\" (0.236 in), which is the baffles' inside: this is the front cap's opening as it shows."},"face_rim_width":{"label":"Front face: the raised rim's width (the face's edge to the pockets)","kind":"length","measurements":[{"id":"face","value":0.124,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/otter-creek-polonium-k f710b8f8d6e8 (Silencer Central's gallery, otter_creek_polonium-k-2.jpg: the front cap nearly face on, from 12 degrees above its axis, 1000 x 1000)","scaleRef":"the front face from edge to edge across the photo, taken as od (1.625): 472 px, 290.5 px/in","method":"read on a crop of the face enlarged 2.6 times with the photo's own pixel grid over it (.cache/batch46/otter-creek-polonium-k/crop.py), across the photo, where the view is square: the collar 118.5 px across","via":"harvest"},"note":"36 px at the left and 35.8 at the right."}]},"face_spoke_width":{"label":"Front face: the width of each arm of the raised cross","kind":"length","measurements":[{"id":"face","value":0.112,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/otter-creek-polonium-k f710b8f8d6e8 (Silencer Central's gallery, otter_creek_polonium-k-2.jpg: the front cap nearly face on, from 12 degrees above its axis, 1000 x 1000)","scaleRef":"the front face from edge to edge across the photo, taken as od (1.625): 472 px, 290.5 px/in","method":"read on a crop of the face enlarged 2.6 times with the photo's own pixel grid over it (.cache/batch46/otter-creek-polonium-k/crop.py), across the photo, where the view is square: the collar 118.5 px across","via":"harvest"},"note":"32.7 px (the upright arm) and 32.3 (the level one)."}]},"face_land_d":{"label":"Front face: the raised round the collar stands on, where the cross's arms meet","kind":"length","measurements":[{"id":"face","value":0.5,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/otter-creek-polonium-k f710b8f8d6e8 (Silencer Central's gallery, otter_creek_polonium-k-2.jpg: the front cap nearly face on, from 12 degrees above its axis, 1000 x 1000)","scaleRef":"the front face from edge to edge across the photo, taken as od (1.625): 472 px, 290.5 px/in","method":"read on a crop of the face enlarged 2.6 times with the photo's own pixel grid over it (.cache/batch46/otter-creek-polonium-k/crop.py), across the photo, where the view is square: the collar 118.5 px across","via":"harvest"},"note":"The pockets' inner corners are 72 px from the centre; each corner is a round, so this is where the arc would be without it."}]},"face_pocket_r":{"label":"Front face: the round in each corner of a pocket","kind":"length","measurements":[{"id":"face","value":0.08,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/otter-creek-polonium-k f710b8f8d6e8 (Silencer Central's gallery, otter_creek_polonium-k-2.jpg: the front cap nearly face on, from 12 degrees above its axis, 1000 x 1000)","scaleRef":"the front face from edge to edge across the photo, taken as od (1.625): 472 px, 290.5 px/in","method":"read on a crop of the face enlarged 2.6 times with the photo's own pixel grid over it (.cache/batch46/otter-creek-polonium-k/crop.py), across the photo, where the view is square: the collar 118.5 px across","via":"harvest"},"note":"23 px at the corners where an arm meets the rim."}]},"face_pockets":{"label":"Front face: pockets","kind":"count","measurements":[{"id":"face","value":4,"unit":"count","source":{"type":"photo","photo":"references/otter-creek-polonium-k f710b8f8d6e8 (Silencer Central's gallery, otter_creek_polonium-k-2.jpg: the front cap nearly face on, from 12 degrees above its axis, 1000 x 1000)","scaleRef":"the front face from edge to edge across the photo, taken as od (1.625): 472 px, 290.5 px/in","method":"read on a crop of the face enlarged 2.6 times with the photo's own pixel grid over it (.cache/batch46/otter-creek-polonium-k/crop.py), across the photo, where the view is square: the collar 118.5 px across","via":"harvest"}}]},"face_pocket_depth":{"label":"Front face: how deep the pockets are","kind":"length","measurements":[{"id":"oblique","value":0.017,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/otter-creek-polonium-k fbc67b6754e3 (Silencer Shop's gallery, polonium-k-556-silencer-shop-central-texas-end-cap: the front cap from about 50 degrees off its axis, 1200 x 1200)","scaleRef":"collar_height (0.095) in the same photo: the far tabs of the collar stand about 20 px above the face","method":"the shadowed wall of the far pockets is about 3 px wide where the collar's tabs are 20 px tall, on a crop enlarged 3.2 times","via":"harvest"}}],"note":"A closed pocket meets no edge, so no silhouette has its depth: this is its wall's width against the collar's height in one oblique photo, both foreshortened alike. Shallow: a relief of a sixty-fourth of an inch or so."},"grooves":{"label":"Shallow grooves round the body, behind the front cap","kind":"count","measurements":[{"id":"side","value":2,"unit":"count","source":{"type":"photo","photo":"references/otter-creek-polonium-k 695e8c80ec35 (Capitol Armory's gallery, ocl_polok_side.jpg: the K lying on white, from the side, the muzzle at the right, 1100 x 1100; serial GK12800, a bronze-coloured mount)","scaleRef":"none: a count","method":"the silhouette's top edge column by column","via":"harvest"}}],"note":"Two, with a ring between them: every side photo."},"groove_depth":{"label":"The grooves' depth (below the ring and the cap)","kind":"length","measurements":[{"id":"capitol-photo","value":0.014,"unit":"in","pm":0.003,"source":{"type":"photo","photo":"references/otter-creek-polonium-k 695e8c80ec35 (Capitol Armory's gallery, ocl_polok_side.jpg: the K lying on white, from the side, the muzzle at the right, 1100 x 1100; serial GK12800, a bronze-coloured mount)","scaleRef":"the can between its two faces, columns 150 and 985.6, as can_rear_x to front_face_x: 175.2 px/in","method":"the top edge at luminance 200 stands 413.55 and 413.25 in the two grooves, 411.0 on the ring between them and 411.4 on the body behind: 2.2 to 2.8 px","via":"harvest"}},{"id":"central-photo","value":0.013,"unit":"in","pm":0.003,"source":{"type":"photo","photo":"references/otter-creek-polonium-k 0817f888c9c7 (Silencer Central's gallery, otter_creek_polonium-k-1.jpg: the K standing on its mount on white, from the side, 1000 x 1000; serial GK0104, the black mount)","scaleRef":"the front cap's width in the same photo, taken as od (1.625): 274.0 px, 168.6 px/in","method":"the silhouette is 268.5 and 269.9 px wide in the grooves, 273.65 on the ring and 274.0 on the cap: 2.0 to 2.6 px a side","via":"harvest"}}],"adopt":{"from":"capitol-photo","reason":"The unit the grooves' places are read on; the other photo's reading is within a thousandth."}},"groove_1_x0":{"label":"Rear groove: its rear edge, ahead of the mount's rear face","kind":"length","measurements":[{"id":"capitol-photo","value":4.206,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/otter-creek-polonium-k 695e8c80ec35 (Capitol Armory's gallery, ocl_polok_side.jpg: the K lying on white, from the side, the muzzle at the right, 1100 x 1100; serial GK12800, a bronze-coloured mount)","scaleRef":"the can between its two faces as can_rear_x to front_face_x: its rear face at column 150 (where the bronze flange ends and the dark chamfer begins on the top edge), its front face at column 985.6 (behind the arc of its rim, which sags 24.9 px: the lens sees that end from 10 degrees off square), 835.6 px, 175.2 px/in","method":"the top edge at luminance 200 drops from 411.4 to 413.5 at column 810.5","via":"harvest"}},{"id":"central-photo","value":4.206,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/otter-creek-polonium-k 0817f888c9c7 (Silencer Central's gallery, otter_creek_polonium-k-1.jpg: the K standing on its mount on white, from the side, 1000 x 1000; serial GK0104, the black mount)","scaleRef":"overall_length (5.3) between the mount's rear face and the collar's tip: 925 px, 174.5 px/in","method":"the silhouette narrows from 272.7 to 268.8 px at column 770","via":"harvest"},"note":"Serial GK0104."}],"adopt":{"from":"capitol-photo","reason":"The later unit; the early one's groove begins at the same place."},"note":"The grooves are placed from Capitol Armory's photo (serial GK12800), and Silencer Shop's photo of a unit with a black mount has the same widths (0.267 and 0.272 in, the ring 0.218). Silencer Central's and Bauer's photos are of an early unit (GK0104) whose grooves begin at the same two places and are 0.04 to 0.05 in longer, with a ring of 0.175: its readings are kept beside these."},"groove_1_x1":{"label":"Rear groove: its front edge, ahead of the mount's rear face","kind":"length","measurements":[{"id":"capitol-photo","value":4.48,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/otter-creek-polonium-k 695e8c80ec35 (Capitol Armory's gallery, ocl_polok_side.jpg: the K lying on white, from the side, the muzzle at the right, 1100 x 1100; serial GK12800, a bronze-coloured mount)","scaleRef":"the can between its two faces as can_rear_x to front_face_x: its rear face at column 150 (where the bronze flange ends and the dark chamfer begins on the top edge), its front face at column 985.6 (behind the arc of its rim, which sags 24.9 px: the lens sees that end from 10 degrees off square), 835.6 px, 175.2 px/in","method":"the top edge rises from 413.4 to 411.15 at column 858.5","via":"harvest"}},{"id":"central-photo","value":4.524,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/otter-creek-polonium-k 0817f888c9c7 (Silencer Central's gallery, otter_creek_polonium-k-1.jpg: the K standing on its mount on white, from the side, 1000 x 1000; serial GK0104, the black mount)","scaleRef":"overall_length (5.3) between the mount's rear face and the collar's tip: 925 px, 174.5 px/in","method":"the silhouette widens from 269.5 to 273.2 px at column 825.5","via":"harvest"},"note":"Serial GK0104: an early unit, its groove 0.044 in longer."}],"adopt":{"from":"capitol-photo","reason":"The later unit's, which a second seller's photo of another unit agrees with (Silencer Shop's: a groove of 0.267 in where this is 0.274); the early unit's groove is longer and stays visible here."}},"groove_2_x0":{"label":"Front groove: its rear edge, ahead of the mount's rear face","kind":"length","measurements":[{"id":"capitol-photo","value":4.696,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/otter-creek-polonium-k 695e8c80ec35 (Capitol Armory's gallery, ocl_polok_side.jpg: the K lying on white, from the side, the muzzle at the right, 1100 x 1100; serial GK12800, a bronze-coloured mount)","scaleRef":"the can between its two faces as can_rear_x to front_face_x: its rear face at column 150 (where the bronze flange ends and the dark chamfer begins on the top edge), its front face at column 985.6 (behind the arc of its rim, which sags 24.9 px: the lens sees that end from 10 degrees off square), 835.6 px, 175.2 px/in","method":"the top edge drops from 411.4 to 413.3 at column 896.5","via":"harvest"}},{"id":"central-photo","value":4.698,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/otter-creek-polonium-k 0817f888c9c7 (Silencer Central's gallery, otter_creek_polonium-k-1.jpg: the K standing on its mount on white, from the side, 1000 x 1000; serial GK0104, the black mount)","scaleRef":"overall_length (5.3) between the mount's rear face and the collar's tip: 925 px, 174.5 px/in","method":"the silhouette narrows from 272.9 to 270.3 px at column 856","via":"harvest"},"note":"Serial GK0104."}],"adopt":{"from":"capitol-photo","reason":"The later unit; the early one's groove begins at the same place."}},"groove_2_x1":{"label":"Front groove: its front edge, ahead of the mount's rear face (the front cap begins here)","kind":"length","measurements":[{"id":"capitol-photo","value":4.962,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/otter-creek-polonium-k 695e8c80ec35 (Capitol Armory's gallery, ocl_polok_side.jpg: the K lying on white, from the side, the muzzle at the right, 1100 x 1100; serial GK12800, a bronze-coloured mount)","scaleRef":"the can between its two faces as can_rear_x to front_face_x: its rear face at column 150 (where the bronze flange ends and the dark chamfer begins on the top edge), its front face at column 985.6 (behind the arc of its rim, which sags 24.9 px: the lens sees that end from 10 degrees off square), 835.6 px, 175.2 px/in","method":"the top edge rises from 412.7 to 410.8 at column 943","via":"harvest"}},{"id":"central-photo","value":5.011,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/otter-creek-polonium-k 0817f888c9c7 (Silencer Central's gallery, otter_creek_polonium-k-1.jpg: the K standing on its mount on white, from the side, 1000 x 1000; serial GK0104, the black mount)","scaleRef":"overall_length (5.3) between the mount's rear face and the collar's tip: 925 px, 174.5 px/in","method":"the silhouette widens from 270.5 to 273.9 px at column 910.5","via":"harvest"},"note":"Serial GK0104: an early unit, its groove 0.049 in longer and its cap that much shorter."}],"adopt":{"from":"capitol-photo","reason":"The later unit's, as groove_1_x1; the early unit's reading stays visible."}},"mount_plug_length":{"label":"The mount's threaded plug inside the can (its 1.375x24 thread and the relief behind it), ahead of the can's rear face","kind":"length","measurements":[{"id":"count","value":0.37,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/otter-creek-polonium-k 6d1e5cc6dd05 (Silencer Central's gallery, otter_creek_polonium-k-3.jpg: the black mount unscrewed and lying beside the can's open rear, 1000 x 1000)","scaleRef":"the thread's own pitch, 24 to the inch by the sellers' 1.375x24","method":"eight crests counted along the plug's lower edge, a third of an inch, and a relief about a pitch wide between them and the flange","via":"harvest"},"note":"The ± is a crest either way and the relief."}],"note":"Not seen once the mount is in: it sets only how deep the mount's own 1/2x28 hole is drawn. The rear thread is the sellers' \"1.375x24\" (Capitol Armory: \"HUB/Bravo 1.375x24 rear threads\")."}}},{"subject":"otter-creek-polonium","title":"Otter Creek Labs Polonium","dimensions":{"can_length":{"label":"The suppressor alone, without a mount: its rear face to its front face","kind":"length","measurements":[{"id":"capitol","value":5.8,"unit":"in","stated":"5.8\" overall length, 1.625\" diameter","source":{"type":"spec","publisher":"retailer","name":"Capitol Armory, Otter Creek Polonium (its SKU OCL-POL556), Features","url":"https://www.capitolarmory.com/otter-creek-labs-polonium-5-56-rifle-suppressor.html","retrieved":"2026-10-06","via":"harvest"}},{"id":"silencer-shop","value":5.8,"unit":"in","stated":"Length: 5.8\"","source":{"type":"spec","publisher":"retailer","name":"Silencer Shop, Otter Creek Labs Polonium Suppressor (its SKU OCL-POL556-MULTI), Technical Specifications","url":"https://www.silencershop.com/otter-creek-labs-polonium.html","retrieved":"2026-10-06","via":"harvest"}},{"id":"silencer-central","value":5.8,"unit":"in","stated":"Length 5.8\"","source":{"type":"spec","publisher":"retailer","name":"Silencer Central, Otter Creek Polonium 5.56, Description and Specs","url":"https://www.silencercentral.com/products/otter-creek-polonium-5-56","retrieved":"2026-10-06","via":"harvest"}},{"id":"kygunco","value":5.8,"unit":"in","stated":"Length: 5.8\", Weight: 13.5 oz, OD: 1.625\"","source":{"type":"spec","publisher":"retailer","name":"KYGunCo, Otter Creek Labs Polonium 5.56 Suppressor 5.8\" Black (MPN POL556, UPC 664533654132)","url":"https://www.kygunco.com/product/otter-creek-labs-pol556-polonium-5.56","retrieved":"2026-10-06","via":"harvest"}},{"id":"bauer","value":5.8,"unit":"in","stated":"Overall Length 5.8″","source":{"type":"spec","publisher":"retailer","name":"Bauer Precision, Otter Creek Labs Polonium 5.56 Suppressor, black (its SKU POL556), Specifications","url":"https://www.bauer-precision.com/otter-creek-labs-polonium-5-56-suppressor-black/","retrieved":"2026-10-06","via":"harvest"}},{"id":"bauer-fde","value":5.8,"unit":"in","stated":"Overall Length 5.8\" (Without Mount)","source":{"type":"spec","publisher":"retailer","name":"Bauer Precision, Otter Creek Labs Polonium 5.56 Suppressor, flat dark earth (its SKU POL556FDE), Specifications","url":"https://www.bauer-precision.com/otter-creek-labs-polonium-5-56-suppressor-fde/","retrieved":"2026-10-06","via":"harvest"}},{"id":"pew-science","value":5.8,"unit":"in","stated":"It has a 1.625-inch diameter and is 5.8 inches in length, without a mount.","source":{"type":"spec","publisher":"review","name":"PEW Science, Sound Signature Review 6.75: Otter Creek Labs Polonium on the MK18 (May 2022)","url":"https://pewscience.com/sound-signature-reviews-free/sss-6-75-ocl-polonium-mk18-556","retrieved":"2026-10-06","via":"harvest"},"note":"Not said to be measured: the figure is the maker's."},{"id":"photo","value":5.86,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/otter-creek-polonium f243e92704d5 (Bauer Precision's gallery: the Polonium lying on white from the side, the muzzle at the right, a black mount, 1280 x 1244)","scaleRef":"overall_length (6.3, PEW Science's with the mount) less collar_height, between the mount's rear face (column 44) and the front face (column 1186.3, behind the arc of its rim). The photo is yawed, the muzzle end further from the lens: the can's own width falls in a straight line from 301.0 px at column 165 to 286.6 at the front face (through the body's and the three rings' widths), and lengths are taken by (column − u0) over that width, as tools/trace.py's tube calibration does","method":"the silhouette column by column at luminance 200 (.cache/batch46/otter-creek-polonium-k/prof.py): the can's rear face is where its rear chamfer begins, column 117.5, its front face column 1186.3","via":"harvest"},"note":"The can's share of the whole at the scale PEW Science's 6.3 gives: 0.06 over the published 5.8, which the two published lengths' last digits and the reading of the mount's rear face (two pixels) cover between them."}],"adopt":{"from":"capitol","reason":"Every seller's figure and the reviewer's are the one number. The photo's reading is the can's share of the 6.3 in whole."},"note":"Otter Creek's figure as its sellers state it; Bauer Precision's page for the flat dark earth one and the reviewer say \"without mount\", Capitol Armory says \"overall length\" of the same 5.8. Taken to be between the two faces, as the Polonium K's is."},"overall_length":{"label":"End to end with the 1/2x28 direct thread mount it is sold with in it: the mount's rear face to the tip of the collar on the front face","kind":"length","measurements":[{"id":"pew-science","value":6.3,"unit":"in","stated":"The total length with the included direct thread adapter is 6.3 inches.","source":{"type":"spec","publisher":"review","name":"PEW Science, Sound Signature Review 6.75: Otter Creek Labs Polonium on the MK18 (May 2022)","url":"https://pewscience.com/sound-signature-reviews-free/sss-6-75-ocl-polonium-mk18-556","retrieved":"2026-10-06","via":"harvest"}},{"id":"photo","value":6.24,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/otter-creek-polonium f243e92704d5 (Bauer Precision's gallery: the Polonium lying on white from the side, the muzzle at the right, a black mount, 1280 x 1244)","scaleRef":"can_length (5.8, the sellers') between the can's two faces, columns 117.5 and 1186.3, the photo's yaw taken out by the can's own width column by column","method":"the mount's rear face (column 44) to the front face reads 6.18 at that scale; collar_height more to the collar's tip, which this photo doesn't show (the front face's near rim hides it)","via":"harvest"},"note":"The same photo read the other way round."}],"adopt":{"from":"pew-science","reason":"The one page that states the length as sold, with the mount; the photo, scaled by the sellers' length without it, reads 0.06 less, inside the two figures' last digits and its own ±."},"note":"What the model is held to. One page states it. Its two ends are taken to be the extremes: the hex's rear face and the notched collar's tip."},"length":{"label":"Length ahead of the barrel's shoulder, installed (to the front face)","kind":"length","measurements":[{"id":"shouldered","value":6.3,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{.overall_length}","via":"harvest"}}],"note":"The whole of it: the mount's rear face (the hex's, with the 1/2x28 thread's mouth in it, the rearmost face in every photo) is taken to bear on the barrel's shoulder. No page on file says what bears on what, or what barrel thread the mount takes."},"od":{"label":"Largest outside diameter","kind":"length","measurements":[{"id":"capitol","value":1.625,"unit":"in","stated":"5.8\" overall length, 1.625\" diameter","source":{"type":"spec","publisher":"retailer","name":"Capitol Armory, Otter Creek Polonium (its SKU OCL-POL556), Features","url":"https://www.capitolarmory.com/otter-creek-labs-polonium-5-56-rifle-suppressor.html","retrieved":"2026-10-06","via":"harvest"}},{"id":"silencer-shop","value":1.625,"unit":"in","stated":"Diameter: Diameter: 1.625\"","source":{"type":"spec","publisher":"retailer","name":"Silencer Shop, Otter Creek Labs Polonium Suppressor (its SKU OCL-POL556-MULTI), Technical Specifications","url":"https://www.silencershop.com/otter-creek-labs-polonium.html","retrieved":"2026-10-06","via":"harvest"},"note":"The doubled word is the page's."},{"id":"silencer-central","value":1.625,"unit":"in","stated":"Diameter 1.625\"","source":{"type":"spec","publisher":"retailer","name":"Silencer Central, Otter Creek Polonium 5.56, Description and Specs","url":"https://www.silencercentral.com/products/otter-creek-polonium-5-56","retrieved":"2026-10-06","via":"harvest"}},{"id":"kygunco","value":1.625,"unit":"in","stated":"Length: 5.8\", Weight: 13.5 oz, OD: 1.625\"","source":{"type":"spec","publisher":"retailer","name":"KYGunCo, Otter Creek Labs Polonium 5.56 Suppressor 5.8\" Black (MPN POL556, UPC 664533654132)","url":"https://www.kygunco.com/product/otter-creek-labs-pol556-polonium-5.56","retrieved":"2026-10-06","via":"harvest"}},{"id":"bauer-fde","value":1.625,"unit":"in","stated":"Outer Diameter 1.625\"","source":{"type":"spec","publisher":"retailer","name":"Bauer Precision, Otter Creek Labs Polonium 5.56 Suppressor, flat dark earth (its SKU POL556FDE), Specifications","url":"https://www.bauer-precision.com/otter-creek-labs-polonium-5-56-suppressor-fde/","retrieved":"2026-10-06","via":"harvest"}},{"id":"pew-science","value":1.625,"unit":"in","stated":"It has a 1.625-inch diameter and is 5.8 inches in length, without a mount.","source":{"type":"spec","publisher":"review","name":"PEW Science, Sound Signature Review 6.75: Otter Creek Labs Polonium on the MK18 (May 2022)","url":"https://pewscience.com/sound-signature-reviews-free/sss-6-75-ocl-polonium-mk18-556","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"capitol","reason":"One figure on every page."}},"od_in_photo":{"label":"The largest diameter as the side photo reads it at the length's scale (a check, not drawn)","kind":"length","measurements":[{"id":"photo","value":1.6,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/otter-creek-polonium f243e92704d5 (Bauer Precision's gallery: the Polonium lying on white from the side, the muzzle at the right, a black mount, 1280 x 1244)","scaleRef":"overall_length (6.3, PEW Science's with the mount) less collar_height, between the mount's rear face (column 44) and the front face (column 1186.3, behind the arc of its rim). The photo is yawed, the muzzle end further from the lens: the can's own width falls in a straight line from 301.0 px at column 165 to 286.6 at the front face (through the body's and the three rings' widths), and lengths are taken by (column − u0) over that width, as tools/trace.py's tube calibration does","method":"the can's width at luminance 200, where 1.625 in along the can would be 1.4% more pixels","via":"harvest"}}],"note":"A black tube reads thin on white: at the scale the published length gives, the published 1.625 reads 1.60, 1.4% under (the Polonium K's photo: 3.4%). The model's lengths are at the length's scale and its diameters at the diameter's."},"can_weight":{"label":"Weight of the suppressor alone, without a mount","kind":"mass","measurements":[{"id":"capitol","value":13.5,"unit":"oz","stated":"13.5 oz","source":{"type":"spec","publisher":"retailer","name":"Capitol Armory, Otter Creek Polonium (its SKU OCL-POL556), Features","url":"https://www.capitolarmory.com/otter-creek-labs-polonium-5-56-rifle-suppressor.html","retrieved":"2026-10-06","via":"harvest"}},{"id":"silencer-shop","value":13.5,"unit":"oz","stated":"Weight: Weight: 13.5 oz","source":{"type":"spec","publisher":"retailer","name":"Silencer Shop, Otter Creek Labs Polonium Suppressor (its SKU OCL-POL556-MULTI), Technical Specifications","url":"https://www.silencershop.com/otter-creek-labs-polonium.html","retrieved":"2026-10-06","via":"harvest"}},{"id":"silencer-central","value":13.5,"unit":"oz","stated":"Weight 13.5 oz","source":{"type":"spec","publisher":"retailer","name":"Silencer Central, Otter Creek Polonium 5.56, Description and Specs","url":"https://www.silencercentral.com/products/otter-creek-polonium-5-56","retrieved":"2026-10-06","via":"harvest"}},{"id":"kygunco","value":13.5,"unit":"oz","stated":"Length: 5.8\", Weight: 13.5 oz, OD: 1.625\"","source":{"type":"spec","publisher":"retailer","name":"KYGunCo, Otter Creek Labs Polonium 5.56 Suppressor 5.8\" Black (MPN POL556, UPC 664533654132)","url":"https://www.kygunco.com/product/otter-creek-labs-pol556-polonium-5.56","retrieved":"2026-10-06","via":"harvest"}},{"id":"bauer","value":13.5,"unit":"oz","stated":"Weight 13.5 oz","source":{"type":"spec","publisher":"retailer","name":"Bauer Precision, Otter Creek Labs Polonium 5.56 Suppressor, black (its SKU POL556), Specifications","url":"https://www.bauer-precision.com/otter-creek-labs-polonium-5-56-suppressor-black/","retrieved":"2026-10-06","via":"harvest"}},{"id":"bauer-fde","value":13.5,"unit":"oz","stated":"Weight 13.5 oz (Without Mount)","source":{"type":"spec","publisher":"retailer","name":"Bauer Precision, Otter Creek Labs Polonium 5.56 Suppressor, flat dark earth (its SKU POL556FDE), Specifications","url":"https://www.bauer-precision.com/otter-creek-labs-polonium-5-56-suppressor-fde/","retrieved":"2026-10-06","via":"harvest"}},{"id":"pew-science","value":13.5,"unit":"oz","stated":"As tested, the silencer weighs 13.5 ounces and the direct-thread mount weighs weighs 2.1 ounces, for a total system weight of 15.6 ounces.","source":{"type":"spec","publisher":"review","name":"PEW Science, Sound Signature Review 6.75: Otter Creek Labs Polonium on the MK18 (May 2022)","url":"https://pewscience.com/sound-signature-reviews-free/sss-6-75-ocl-polonium-mk18-556","retrieved":"2026-10-06","via":"harvest"},"note":"\"As tested\": the one figure said of the unit in hand (the doubled word is the page's)."}],"adopt":{"from":"pew-science","reason":"The reviewer's as-tested weight; every seller's figure is the same."}},"mount_weight":{"label":"Weight of the 1/2x28 direct thread mount it is sold with","kind":"mass","measurements":[{"id":"pew-science","value":2.1,"unit":"oz","stated":"As tested, the silencer weighs 13.5 ounces and the direct-thread mount weighs weighs 2.1 ounces, for a total system weight of 15.6 ounces.","source":{"type":"spec","publisher":"review","name":"PEW Science, Sound Signature Review 6.75: Otter Creek Labs Polonium on the MK18 (May 2022)","url":"https://pewscience.com/sound-signature-reviews-free/sss-6-75-ocl-polonium-mk18-556","retrieved":"2026-10-06","via":"harvest"}}]},"weight":{"label":"Weight as sold, with the direct thread mount in it","kind":"mass","measurements":[{"id":"pew-science","value":15.6,"unit":"oz","stated":"As tested, the silencer weighs 13.5 ounces and the direct-thread mount weighs weighs 2.1 ounces, for a total system weight of 15.6 ounces.","source":{"type":"spec","publisher":"review","name":"PEW Science, Sound Signature Review 6.75: Otter Creek Labs Polonium on the MK18 (May 2022)","url":"https://pewscience.com/sound-signature-reviews-free/sss-6-75-ocl-polonium-mk18-556","retrieved":"2026-10-06","via":"harvest"}},{"id":"sum","value":15.6,"unit":"oz","pm":0.07,"source":{"type":"derived","expr":"{.can_weight} + {.mount_weight}","via":"harvest"}}],"adopt":{"from":"pew-science","reason":"The reviewer's total for the suppressor as tested with its mount; the sellers' 13.5 oz without a mount and the mount's own 2.1 come to the same."},"note":"The part's weight. A buyer's review on Silencer Shop's page says the same of the sellers' figure: \"Advertised weight DOES NOT INCLUDE HUB MOUNT.\" KYGunCo's \"Weight 2 lb\" is its parcel's."},"thread_length":{"label":"Barrel thread length it takes, or is made for","kind":"length","measurements":[],"note":"No page on file says what length of 1/2x28 barrel thread the mount takes or is made for, and no manual of Otter Creek's is hosted anywhere the harvester may read. The mount is threaded through and the can is open behind it, so a barrel's threaded end of any length stands in air as drawn."},"thread_pitch":{"label":"The mount's thread, its pitch","kind":"length","measurements":[{"id":"sellers","value":0.03571,"unit":"in","pm":0.00005,"stated":"1/2x28 direct thread mount","source":{"type":"spec","publisher":"retailer","name":"Capitol Armory, Otter Creek Polonium (its SKU OCL-POL556), Features","url":"https://www.capitolarmory.com/otter-creek-labs-polonium-5-56-rifle-suppressor.html","retrieved":"2026-10-06","via":"harvest"},"note":"An inch over 28. Capitol Armory's table has \"Thread Pitch 1/2x28\" too."}],"note":"28 to the inch by every seller's \"1/2x28\"."},"thread_major_d":{"label":"The barrel thread the mount takes, its major diameter (the crests the mount's grooves are drawn a gap outside)","kind":"length","measurements":[{"id":"army","value":0.4957,"unit":"in","pm":0.0033,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.thread_major_d}","via":"harvest"},"note":"The Army barrel's 1/2-28 UNEF-2A, drawing 8448549, as the catalog's barrels carry it: the thread the sellers name for the mount. Nothing of the mount's own thread is measured."}]},"thread_minor_d":{"label":"The barrel thread the mount takes, its minor diameter (the roots the mount's lands are drawn a gap outside)","kind":"length","measurements":[{"id":"army","value":0.4551,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.thread_minor_d}","via":"harvest"}}]},"mount_hex_flats":{"label":"The mount's hex, across its flats","kind":"length","measurements":[{"id":"photo","value":0.803,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/otter-creek-polonium f243e92704d5 (Bauer Precision's gallery: the Polonium lying on white from the side, the muzzle at the right, a black mount, 1280 x 1244)","scaleRef":"the can's own width beside it, taken as od (1.625): 302.5 px at the mount, 186.2 px/in","method":"the hex stands with a flat to the lens, so its height is corner to corner: 172.6 px over columns 56 to 96, 0.927 in, times the cosine of 30 degrees","via":"harvest"}}],"note":"Read on the black mount in Bauer Precision's photo of this can. Capitol Armory's, Silencer Central's and Blackstone's units have a bronze-coloured mount of the same form, Silencer Shop's a grey one."},"mount_hex_end_d":{"label":"The mount's hex, the diameter of its rear face (where the turned chamfer that relieves its corners begins)","kind":"length","measurements":[{"id":"photo","value":0.79,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/otter-creek-polonium f243e92704d5 (Bauer Precision's gallery: the Polonium lying on white from the side, the muzzle at the right, a black mount, 1280 x 1244)","scaleRef":"the can's own width beside it, taken as od (1.625): 302.5 px at the mount, 186.2 px/in","method":"the silhouette's rear end, columns 36 to 56: the rear face's rim, a circle seen from off square, is 141 to 155 px across by how its arc is fitted, and from it the outline rises to the hex's corners at about 45 degrees","via":"harvest"},"note":"Drawn with a 45 degree chamfer from this circle."}]},"mount_hex_length":{"label":"The mount's hex: its rear face to the flange's rear face","kind":"length","measurements":[{"id":"photo","value":0.34,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/otter-creek-polonium f243e92704d5 (Bauer Precision's gallery: the Polonium lying on white from the side, the muzzle at the right, a black mount, 1280 x 1244)","scaleRef":"overall_length (6.3, PEW Science's with the mount) less collar_height, between the mount's rear face (column 44) and the front face (column 1186.3, behind the arc of its rim). The photo is yawed, the muzzle end further from the lens: the can's own width falls in a straight line from 301.0 px at column 165 to 286.6 at the front face (through the body's and the three rings' widths), and lengths are taken by (column − u0) over that width, as tools/trace.py's tube calibration does","method":"the hex's rear face at column 44, where the arc of its rim ends and its chamfer begins (the silhouette's tip is column 36); the flange's rear face 8 columns behind the can's (its edge shows between the hex and the dark line where it meets the can)","via":"harvest"}}]},"can_rear_x":{"label":"The can's rear face, ahead of the mount's rear face (the hex and the flange stand behind it)","kind":"length","measurements":[{"id":"photo","value":0.381,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/otter-creek-polonium f243e92704d5 (Bauer Precision's gallery: the Polonium lying on white from the side, the muzzle at the right, a black mount, 1280 x 1244)","scaleRef":"overall_length (6.3, PEW Science's with the mount) less collar_height, between the mount's rear face (column 44) and the front face (column 1186.3, behind the arc of its rim). The photo is yawed, the muzzle end further from the lens: the can's own width falls in a straight line from 301.0 px at column 165 to 286.6 at the front face (through the body's and the three rings' widths), and lengths are taken by (column − u0) over that width, as tools/trace.py's tube calibration does","method":"the hex's rear face at column 44; the can's rear face at column 117.5, where the silhouette's rim (277 px across) ends and the can's chamfer begins","via":"harvest"}},{"id":"published","value":0.5,"unit":"in","pm":0.1,"source":{"type":"derived","expr":"{.overall_length} - {.can_length}","via":"harvest"},"note":"Two published lengths, each rounded to a tenth, and the collar at the front end counted in the first and not in the second."}],"adopt":{"from":"photo","reason":"Read on the photo in proportion to the whole; the published lengths' difference is good to a tenth and includes the collar."},"note":"PEW Science's two lengths put it at 0.5 (6.3 less 5.8, each to a tenth, the collar counted in the first). The Polonium K's ledger reads 0.435 for what is by its weight the same mount, on another photo: each can keeps its own reading, and they differ by what two pixels at the mount's rear face and the two photos' lenses leave."},"rear_rim_d":{"label":"The can's rear rim, where its rear chamfer begins (the mount's flange is a little inside it)","kind":"length","measurements":[{"id":"photo","value":1.49,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/otter-creek-polonium f243e92704d5 (Bauer Precision's gallery: the Polonium lying on white from the side, the muzzle at the right, a black mount, 1280 x 1244)","scaleRef":"the can's own width beside it, taken as od (1.625): 301.7 px there, 185.7 px/in","method":"the silhouette's width where the arc of the rear rim ends and the chamfer's straight line begins: 277 px at column 117.5","via":"harvest"}}]},"rear_chamfer_x":{"label":"Where the can's rear chamfer reaches its full diameter, ahead of the mount's rear face","kind":"length","measurements":[{"id":"photo","value":0.603,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/otter-creek-polonium f243e92704d5 (Bauer Precision's gallery: the Polonium lying on white from the side, the muzzle at the right, a black mount, 1280 x 1244)","scaleRef":"overall_length (6.3, PEW Science's with the mount) less collar_height, between the mount's rear face (column 44) and the front face (column 1186.3, behind the arc of its rim). The photo is yawed, the muzzle end further from the lens: the can's own width falls in a straight line from 301.0 px at column 165 to 286.6 at the front face (through the body's and the three rings' widths), and lengths are taken by (column − u0) over that width, as tools/trace.py's tube calibration does","method":"the silhouette's width rises in a straight line from 277 px at column 117.5 to the body's 301 at column 160","via":"harvest"}},{"id":"capitol-photo","value":0.585,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/otter-creek-polonium e5f6d6d4781b (Capitol Armory's gallery: the Polonium lying on white from the side, the muzzle at the right, 1100 x 1100; serial G11796, a bronze-coloured mount)","scaleRef":"the can between its two faces as can_rear_x to front_face_x: its rear face at column 147 (where the bronze flange ends and the dark chamfer begins on the top edge), its front face at column 964 (behind the arc of its rim, which sags 30.9 px: the lens sees that end from 15 degrees off square), 817 px, 139.5 px/in","method":"the top edge at luminance 200 rises in a straight line from column 147 to the body's level at column 175.5: a chamfer 0.204 in long, from can_rear_x","via":"harvest"}}],"adopt":{"from":"photo","reason":"The larger photo, read on both edges; the other unit's chamfer reads 0.02 shorter, within the two readings' ±."}},"collar_height":{"label":"The notched collar round the bore: how far it stands out of the front face","kind":"length","measurements":[{"id":"side","value":0.062,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/otter-creek-polonium 45a291775460 (Silencer Shop's gallery: the Polonium standing on white from the side, a hard shadow down one side, 1200 x 1200)","scaleRef":"the can between its lit edge and its shadowed edge where the shadow leaves it (rows 457 to 727 in the photo turned muzzle to the right), taken as od (1.625): 270 px, 166 px/in","method":"the collar's tabs show past the front face: the face is behind the arc of its rim at column 1104.3, the collar's tip between columns 1113 and 1116 (its own rim is rounded)","via":"harvest"},"note":"The lens is level with the can's middle, so the collar's foot is behind the face's near rim and only its tip shows: the height is the tip's against the face's plane where that meets the silhouette."},{"id":"oblique","value":0.12,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/otter-creek-polonium 2352f4807f8d (Blackstone Shooting's gallery: the flat dark earth Polonium standing, seen from 9 degrees above its front face, 2000 x 2000; serial G2521, a bronze-coloured mount)","scaleRef":"the front face's own width across the photo, taken as od (1.625): 490 px, 301.5 px/in","method":"a tab's outer wall, seen almost square from the side, is 38.5 px tall from its foot on the face to its top edge; less the 3 px of its top that the tilt shows, and over the tilt's cosine","via":"harvest"},"note":"The ± is three pixels and the tilt (read off the face's ellipse, 73.5 px deep)."}],"adopt":{"from":"side","reason":"A silhouette against a plane, as every other length here is read; the oblique photo of another unit reads twice that, and nothing on file says whether units differ or one reading is wrong. The model's collar is the shorter."},"note":"Two photos of two units, two methods, and they don't agree: the difference stays visible. Sellers call it the external flash hider (Capitol Armory: \"Built-in internal and external flash hiders\"). The Polonium K's ledger has 0.095 for its own collar, from a side view."},"front_face_x":{"label":"The front face, ahead of the mount's rear face","kind":"length","measurements":[{"id":"whole","value":6.238,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{.overall_length} - {.collar_height}","via":"harvest"}}],"note":"The whole less the collar: the side photo the lengths are read on doesn't show the collar's tip."},"front_edge_break":{"label":"The front cap's front corner: the break on it","kind":"length","measurements":[{"id":"photo","value":0.02,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/otter-creek-polonium 45a291775460 (Silencer Shop's gallery: the Polonium standing on white from the side, 1200 x 1200)","scaleRef":"the can between its lit edge and its shadowed edge, taken as od (1.625): 270 px, 166 px/in","method":"the lit edge holds its line to column 1104 and has left it by 1107: a corner taken off over about 3 px","via":"harvest"}}]},"collar_od":{"label":"The notched collar's outside diameter","kind":"length","measurements":[{"id":"face","value":0.43,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/otter-creek-polonium 23fae53d9890 (Bauer Precision's gallery: the black Polonium's front cap face on, 800 x 800)","scaleRef":"the front face from edge to edge, taken as od (1.625): 613.5 px across and the same down (a view square to the face), 377.5 px/in","method":"luminance along the four diagonals from the face's centre (.cache/batch46/otter-creek-polonium/face.py), where the collar's tabs are: the dark line at the collar's outer wall is 81.2 px from the hole's centre (80.3 to 81.8 on the four)","via":"harvest"}}]},"collar_notches":{"label":"Notches in the collar","kind":"count","measurements":[{"id":"face","value":4,"unit":"count","source":{"type":"photo","photo":"references/otter-creek-polonium 23fae53d9890 (Bauer Precision's gallery: the black Polonium's front cap face on, 800 x 800)","scaleRef":"the front face from edge to edge, taken as od (1.625): 613.5 px across and the same down (a view square to the face), 377.5 px/in","method":"luminance along the four diagonals from the face's centre (.cache/batch46/otter-creek-polonium/face.py), where the collar's tabs are: the dark line at the collar's outer wall is 81.2 px from the hole's centre (80.3 to 81.8 on the four)","via":"harvest"}}],"note":"At twelve, three, six and nine with the cross's four arms."},"collar_notch_width":{"label":"The collar's notches, their width","kind":"length","measurements":[{"id":"face","value":0.093,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/otter-creek-polonium 23fae53d9890 (Bauer Precision's gallery: the black Polonium's front cap face on, 800 x 800)","scaleRef":"the front face from edge to edge, taken as od (1.625): 613.5 px across and the same down (a view square to the face), 377.5 px/in","method":"luminance along the four diagonals from the face's centre (.cache/batch46/otter-creek-polonium/face.py), where the collar's tabs are: the dark line at the collar's outer wall is 81.2 px from the hole's centre (80.3 to 81.8 on the four)","via":"harvest"},"note":"The notch at twelve on a crop enlarged 2.1 times: 35.2 px."}]},"bore_d":{"label":"The hole in the front face (inside the collar)","kind":"length","measurements":[{"id":"face","value":0.291,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/otter-creek-polonium 23fae53d9890 (Bauer Precision's gallery: the black Polonium's front cap face on, 800 x 800)","scaleRef":"the front face from edge to edge, taken as od (1.625): 613.5 px across and the same down (a view square to the face), 377.5 px/in","method":"luminance along the four diagonals from the face's centre (.cache/batch46/otter-creek-polonium/face.py), where the collar's tabs are: the dark line at the collar's outer wall is 81.2 px from the hole's centre (80.3 to 81.8 on the four)","via":"harvest"},"note":"The dark hole: 108 px along the row through its centre (through two notches), 113 on the diagonals, where the tabs' inner walls are in shadow: 110."}],"note":"Larger than the sellers' \"6mm bore\" (0.236 in), which is the baffles' inside: this is the front cap's opening as it shows."},"face_rim_width":{"label":"Front face: the raised rim's width (the face's edge to the pockets)","kind":"length","measurements":[{"id":"face","value":0.103,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/otter-creek-polonium 23fae53d9890 (Bauer Precision's gallery: the black Polonium's front cap face on, 800 x 800)","scaleRef":"the front face from edge to edge, taken as od (1.625): 613.5 px across and the same down (a view square to the face), 377.5 px/in","method":"luminance along the four diagonals from the face's centre (.cache/batch46/otter-creek-polonium/face.py), where the collar's tabs are: the dark line at the collar's outer wall is 81.2 px from the hole's centre (80.3 to 81.8 on the four)","via":"harvest"},"note":"On two diagonals the pocket's outer wall is a dark line 266.5 px from the centre and the face's edge 305.6: 39 px."}]},"face_spoke_width":{"label":"Front face: the width of each arm of the raised cross","kind":"length","measurements":[{"id":"face","value":0.111,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/otter-creek-polonium 23fae53d9890 (Bauer Precision's gallery: the black Polonium's front cap face on, 800 x 800)","scaleRef":"the front face from edge to edge, taken as od (1.625): 613.5 px across and the same down (a view square to the face), 377.5 px/in","method":"luminance along the four diagonals from the face's centre (.cache/batch46/otter-creek-polonium/face.py), where the collar's tabs are: the dark line at the collar's outer wall is 81.2 px from the hole's centre (80.3 to 81.8 on the four)","via":"harvest"},"note":"Across the upright arm 170 px above the centre: the two pockets' walls are dark lines 41.8 px apart (the level arm reads 44.5 through a bright speck)."}]},"face_land_d":{"label":"Front face: the raised round the collar stands on, where the cross's arms meet","kind":"length","measurements":[{"id":"face","value":0.503,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/otter-creek-polonium 23fae53d9890 (Bauer Precision's gallery: the black Polonium's front cap face on, 800 x 800)","scaleRef":"the front face from edge to edge, taken as od (1.625): 613.5 px across and the same down (a view square to the face), 377.5 px/in","method":"luminance along the four diagonals from the face's centre (.cache/batch46/otter-creek-polonium/face.py), where the collar's tabs are: the dark line at the collar's outer wall is 81.2 px from the hole's centre (80.3 to 81.8 on the four)","via":"harvest"},"note":"The pockets' inner walls are a dark line 95.0 px from the hole's centre on the four diagonals (93.3 to 96.8)."}]},"face_pocket_r":{"label":"Front face: the round in each corner of a pocket","kind":"length","measurements":[{"id":"face","value":0.07,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/otter-creek-polonium 23fae53d9890 (Bauer Precision's gallery: the black Polonium's front cap face on, 800 x 800)","scaleRef":"the front face from edge to edge, taken as od (1.625): 613.5 px across and the same down (a view square to the face), 377.5 px/in","method":"luminance along the four diagonals from the face's centre (.cache/batch46/otter-creek-polonium/face.py), where the collar's tabs are: the dark line at the collar's outer wall is 81.2 px from the hole's centre (80.3 to 81.8 on the four)","via":"harvest"},"note":"About 27 px where an arm meets the rim, on the enlarged crop."}]},"face_pockets":{"label":"Front face: pockets","kind":"count","measurements":[{"id":"face","value":4,"unit":"count","source":{"type":"photo","photo":"references/otter-creek-polonium 23fae53d9890 (Bauer Precision's gallery: the black Polonium's front cap face on, 800 x 800)","scaleRef":"the front face from edge to edge, taken as od (1.625): 613.5 px across and the same down (a view square to the face), 377.5 px/in","method":"luminance along the four diagonals from the face's centre (.cache/batch46/otter-creek-polonium/face.py), where the collar's tabs are: the dark line at the collar's outer wall is 81.2 px from the hole's centre (80.3 to 81.8 on the four)","via":"harvest"}}]},"face_pocket_depth":{"label":"Front face: how deep the pockets are","kind":"length","measurements":[{"id":"oblique","value":0.01,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/otter-creek-polonium 2352f4807f8d (Blackstone Shooting's gallery: the flat dark earth Polonium standing, seen from 9 degrees above its front face, 2000 x 2000)","scaleRef":"the front face's own width across the photo, taken as od (1.625): 490 px, 301.5 px/in","method":"the far pockets' walls, facing the lens, are lit bands 2 to 3 px wide","via":"harvest"}}],"note":"A closed pocket meets no edge, so no silhouette has its depth. A shallow relief."},"grooves":{"label":"Shallow grooves round the body, behind the front cap","kind":"count","measurements":[{"id":"side","value":4,"unit":"count","source":{"type":"photo","photo":"references/otter-creek-polonium e5f6d6d4781b (Capitol Armory's gallery: the Polonium lying on white from the side, the muzzle at the right, 1100 x 1100; serial G11796, a bronze-coloured mount)","scaleRef":"none: a count","method":"the silhouette's top edge column by column","via":"harvest"}}],"note":"Four, with three rings between them: every side photo of the Polonium (Bauer Precision's, Capitol Armory's, Silencer Shop's, Blackstone's). The Polonium K has two."},"groove_depth":{"label":"The grooves' depth (below the rings and the cap)","kind":"length","measurements":[{"id":"capitol-photo","value":0.014,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/otter-creek-polonium e5f6d6d4781b (Capitol Armory's gallery: the Polonium lying on white from the side, the muzzle at the right, 1100 x 1100; serial G11796, a bronze-coloured mount)","scaleRef":"the can between its two faces as can_rear_x to front_face_x: its rear face at column 147 (where the bronze flange ends and the dark chamfer begins on the top edge), its front face at column 964 (behind the arc of its rim, which sags 30.9 px: the lens sees that end from 15 degrees off square), 817 px, 139.5 px/in","method":"the top edge at luminance 200 stands 437.4 to 437.7 in the four grooves and 435.5 on the rings and the body: 2.0 px","via":"harvest"}},{"id":"bauer-photo","value":0.018,"unit":"in","pm":0.003,"source":{"type":"photo","photo":"references/otter-creek-polonium f243e92704d5 (Bauer Precision's gallery: the Polonium lying on white from the side, the muzzle at the right, a black mount, 1280 x 1244)","scaleRef":"the can's own width beside each groove, taken as od (1.625): 290 px, 178.5 px/in","method":"the silhouette is 6.0 to 7.3 px narrower in the grooves than on the rings beside them: 3.0 to 3.65 px a side","via":"harvest"},"note":"This unit's grooves are deeper and longer than Capitol Armory's."}],"adopt":{"from":"capitol-photo","reason":"The unit the grooves' places are read on; Bauer's unit reads four thousandths deeper, inside the two ±."}},"groove_1_x0":{"label":"First groove from the rear: its rear edge, ahead of the mount's rear face","kind":"length","measurements":[{"id":"capitol-photo","value":4.26,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/otter-creek-polonium e5f6d6d4781b (Capitol Armory's gallery: the Polonium lying on white from the side, the muzzle at the right, 1100 x 1100; serial G11796, a bronze-coloured mount)","scaleRef":"the can between its two faces as can_rear_x to front_face_x: its rear face at column 147 (where the bronze flange ends and the dark chamfer begins on the top edge), its front face at column 964 (behind the arc of its rim, which sags 30.9 px: the lens sees that end from 15 degrees off square), 817 px, 139.5 px/in","method":"the top edge at luminance 200 drops at column 688","via":"harvest"}},{"id":"bauer-photo","value":4.252,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/otter-creek-polonium f243e92704d5 (Bauer Precision's gallery: the Polonium lying on white from the side, the muzzle at the right, a black mount, 1280 x 1244)","scaleRef":"overall_length (6.3, PEW Science's with the mount) less collar_height, between the mount's rear face (column 44) and the front face (column 1186.3, behind the arc of its rim). The photo is yawed, the muzzle end further from the lens: the can's own width falls in a straight line from 301.0 px at column 165 to 286.6 at the front face (through the body's and the three rings' widths), and lengths are taken by (column − u0) over that width, as tools/trace.py's tube calibration does","method":"the silhouette narrows at column 836","via":"harvest"}}],"adopt":{"from":"capitol-photo","reason":"One unit for all four grooves; the other's begins at the same place."},"note":"The grooves are placed from Capitol Armory's photo (serial G11796), as the Polonium K's are from Capitol Armory's of that can: on both cans its unit has the shorter grooves and the wider rings. Bauer Precision's unit, the larger photo, has each groove beginning at the same place within a hundredth and running 0.02 to 0.035 in further forward: its readings are kept beside these."},"groove_1_x1":{"label":"First groove from the rear: its front edge, ahead of the mount's rear face","kind":"length","measurements":[{"id":"capitol-photo","value":4.525,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/otter-creek-polonium e5f6d6d4781b (Capitol Armory's gallery: the Polonium lying on white from the side, the muzzle at the right, 1100 x 1100; serial G11796, a bronze-coloured mount)","scaleRef":"the can between its two faces as can_rear_x to front_face_x: its rear face at column 147 (where the bronze flange ends and the dark chamfer begins on the top edge), its front face at column 964 (behind the arc of its rim, which sags 30.9 px: the lens sees that end from 15 degrees off square), 817 px, 139.5 px/in","method":"the top edge rises at column 725","via":"harvest"}},{"id":"bauer-photo","value":4.554,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/otter-creek-polonium f243e92704d5 (Bauer Precision's gallery: the Polonium lying on white from the side, the muzzle at the right, a black mount, 1280 x 1244)","scaleRef":"overall_length (6.3, PEW Science's with the mount) less collar_height, between the mount's rear face (column 44) and the front face (column 1186.3, behind the arc of its rim). The photo is yawed, the muzzle end further from the lens: the can's own width falls in a straight line from 301.0 px at column 165 to 286.6 at the front face (through the body's and the three rings' widths), and lengths are taken by (column − u0) over that width, as tools/trace.py's tube calibration does","method":"the silhouette widens at column 890","via":"harvest"}}],"adopt":{"from":"capitol-photo","reason":"One unit for all four grooves; the other's groove is 0.03 in longer, inside the two ±."}},"groove_2_x0":{"label":"Second groove: its rear edge, ahead of the mount's rear face","kind":"length","measurements":[{"id":"capitol-photo","value":4.754,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/otter-creek-polonium e5f6d6d4781b (Capitol Armory's gallery: the Polonium lying on white from the side, the muzzle at the right, 1100 x 1100; serial G11796, a bronze-coloured mount)","scaleRef":"the can between its two faces as can_rear_x to front_face_x: its rear face at column 147 (where the bronze flange ends and the dark chamfer begins on the top edge), its front face at column 964 (behind the arc of its rim, which sags 30.9 px: the lens sees that end from 15 degrees off square), 817 px, 139.5 px/in","method":"the top edge drops at column 757","via":"harvest"}},{"id":"bauer-photo","value":4.756,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/otter-creek-polonium f243e92704d5 (Bauer Precision's gallery: the Polonium lying on white from the side, the muzzle at the right, a black mount, 1280 x 1244)","scaleRef":"overall_length (6.3, PEW Science's with the mount) less collar_height, between the mount's rear face (column 44) and the front face (column 1186.3, behind the arc of its rim). The photo is yawed, the muzzle end further from the lens: the can's own width falls in a straight line from 301.0 px at column 165 to 286.6 at the front face (through the body's and the three rings' widths), and lengths are taken by (column − u0) over that width, as tools/trace.py's tube calibration does","method":"the silhouette narrows at column 926","via":"harvest"}}],"adopt":{"from":"capitol-photo","reason":"One unit for all four grooves; the two agree."}},"groove_2_x1":{"label":"Second groove: its front edge, ahead of the mount's rear face","kind":"length","measurements":[{"id":"capitol-photo","value":5.016,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/otter-creek-polonium e5f6d6d4781b (Capitol Armory's gallery: the Polonium lying on white from the side, the muzzle at the right, 1100 x 1100; serial G11796, a bronze-coloured mount)","scaleRef":"the can between its two faces as can_rear_x to front_face_x: its rear face at column 147 (where the bronze flange ends and the dark chamfer begins on the top edge), its front face at column 964 (behind the arc of its rim, which sags 30.9 px: the lens sees that end from 15 degrees off square), 817 px, 139.5 px/in","method":"the top edge rises at column 793.5","via":"harvest"}},{"id":"bauer-photo","value":5.043,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/otter-creek-polonium f243e92704d5 (Bauer Precision's gallery: the Polonium lying on white from the side, the muzzle at the right, a black mount, 1280 x 1244)","scaleRef":"overall_length (6.3, PEW Science's with the mount) less collar_height, between the mount's rear face (column 44) and the front face (column 1186.3, behind the arc of its rim). The photo is yawed, the muzzle end further from the lens: the can's own width falls in a straight line from 301.0 px at column 165 to 286.6 at the front face (through the body's and the three rings' widths), and lengths are taken by (column − u0) over that width, as tools/trace.py's tube calibration does","method":"the silhouette widens at column 977","via":"harvest"}}],"adopt":{"from":"capitol-photo","reason":"One unit for all four grooves; the other's groove is 0.03 in longer, inside the two ±."}},"groove_3_x0":{"label":"Third groove: its rear edge, ahead of the mount's rear face","kind":"length","measurements":[{"id":"capitol-photo","value":5.249,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/otter-creek-polonium e5f6d6d4781b (Capitol Armory's gallery: the Polonium lying on white from the side, the muzzle at the right, 1100 x 1100; serial G11796, a bronze-coloured mount)","scaleRef":"the can between its two faces as can_rear_x to front_face_x: its rear face at column 147 (where the bronze flange ends and the dark chamfer begins on the top edge), its front face at column 964 (behind the arc of its rim, which sags 30.9 px: the lens sees that end from 15 degrees off square), 817 px, 139.5 px/in","method":"the top edge drops at column 826","via":"harvest"}},{"id":"bauer-photo","value":5.25,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/otter-creek-polonium f243e92704d5 (Bauer Precision's gallery: the Polonium lying on white from the side, the muzzle at the right, a black mount, 1280 x 1244)","scaleRef":"overall_length (6.3, PEW Science's with the mount) less collar_height, between the mount's rear face (column 44) and the front face (column 1186.3, behind the arc of its rim). The photo is yawed, the muzzle end further from the lens: the can's own width falls in a straight line from 301.0 px at column 165 to 286.6 at the front face (through the body's and the three rings' widths), and lengths are taken by (column − u0) over that width, as tools/trace.py's tube calibration does","method":"the silhouette narrows at column 1013.5","via":"harvest"}}],"adopt":{"from":"capitol-photo","reason":"One unit for all four grooves; the two agree."}},"groove_3_x1":{"label":"Third groove: its front edge, ahead of the mount's rear face","kind":"length","measurements":[{"id":"capitol-photo","value":5.503,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/otter-creek-polonium e5f6d6d4781b (Capitol Armory's gallery: the Polonium lying on white from the side, the muzzle at the right, 1100 x 1100; serial G11796, a bronze-coloured mount)","scaleRef":"the can between its two faces as can_rear_x to front_face_x: its rear face at column 147 (where the bronze flange ends and the dark chamfer begins on the top edge), its front face at column 964 (behind the arc of its rim, which sags 30.9 px: the lens sees that end from 15 degrees off square), 817 px, 139.5 px/in","method":"the top edge rises at column 861.5","via":"harvest"}},{"id":"bauer-photo","value":5.537,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/otter-creek-polonium f243e92704d5 (Bauer Precision's gallery: the Polonium lying on white from the side, the muzzle at the right, a black mount, 1280 x 1244)","scaleRef":"overall_length (6.3, PEW Science's with the mount) less collar_height, between the mount's rear face (column 44) and the front face (column 1186.3, behind the arc of its rim). The photo is yawed, the muzzle end further from the lens: the can's own width falls in a straight line from 301.0 px at column 165 to 286.6 at the front face (through the body's and the three rings' widths), and lengths are taken by (column − u0) over that width, as tools/trace.py's tube calibration does","method":"the silhouette widens at column 1064","via":"harvest"}}],"adopt":{"from":"capitol-photo","reason":"One unit for all four grooves; the other's groove is 0.03 in longer, inside the two ±."}},"groove_4_x0":{"label":"Fourth groove, behind the front cap: its rear edge, ahead of the mount's rear face","kind":"length","measurements":[{"id":"capitol-photo","value":5.743,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/otter-creek-polonium e5f6d6d4781b (Capitol Armory's gallery: the Polonium lying on white from the side, the muzzle at the right, 1100 x 1100; serial G11796, a bronze-coloured mount)","scaleRef":"the can between its two faces as can_rear_x to front_face_x: its rear face at column 147 (where the bronze flange ends and the dark chamfer begins on the top edge), its front face at column 964 (behind the arc of its rim, which sags 30.9 px: the lens sees that end from 15 degrees off square), 817 px, 139.5 px/in","method":"the top edge drops at column 895","via":"harvest"}},{"id":"bauer-photo","value":5.751,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/otter-creek-polonium f243e92704d5 (Bauer Precision's gallery: the Polonium lying on white from the side, the muzzle at the right, a black mount, 1280 x 1244)","scaleRef":"overall_length (6.3, PEW Science's with the mount) less collar_height, between the mount's rear face (column 44) and the front face (column 1186.3, behind the arc of its rim). The photo is yawed, the muzzle end further from the lens: the can's own width falls in a straight line from 301.0 px at column 165 to 286.6 at the front face (through the body's and the three rings' widths), and lengths are taken by (column − u0) over that width, as tools/trace.py's tube calibration does","method":"the silhouette narrows at column 1101.5","via":"harvest"}}],"adopt":{"from":"capitol-photo","reason":"One unit for all four grooves; the two agree."}},"groove_4_x1":{"label":"Fourth groove: its front edge, ahead of the mount's rear face (the front cap begins here)","kind":"length","measurements":[{"id":"capitol-photo","value":6.005,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/otter-creek-polonium e5f6d6d4781b (Capitol Armory's gallery: the Polonium lying on white from the side, the muzzle at the right, 1100 x 1100; serial G11796, a bronze-coloured mount)","scaleRef":"the can between its two faces as can_rear_x to front_face_x: its rear face at column 147 (where the bronze flange ends and the dark chamfer begins on the top edge), its front face at column 964 (behind the arc of its rim, which sags 30.9 px: the lens sees that end from 15 degrees off square), 817 px, 139.5 px/in","method":"the top edge rises at column 931.5","via":"harvest"}},{"id":"bauer-photo","value":6.026,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/otter-creek-polonium f243e92704d5 (Bauer Precision's gallery: the Polonium lying on white from the side, the muzzle at the right, a black mount, 1280 x 1244)","scaleRef":"overall_length (6.3, PEW Science's with the mount) less collar_height, between the mount's rear face (column 44) and the front face (column 1186.3, behind the arc of its rim). The photo is yawed, the muzzle end further from the lens: the can's own width falls in a straight line from 301.0 px at column 165 to 286.6 at the front face (through the body's and the three rings' widths), and lengths are taken by (column − u0) over that width, as tools/trace.py's tube calibration does","method":"the silhouette widens at column 1149.5","via":"harvest"}}],"adopt":{"from":"capitol-photo","reason":"One unit for all four grooves; the other's groove is 0.02 in longer, inside the two ±."}},"mount_plug_length":{"label":"The mount's threaded plug inside the can (its 1.375x24 thread), ahead of the can's rear face","kind":"length","measurements":[{"id":"count","value":0.25,"unit":"in","pm":0.09,"source":{"type":"photo","photo":"references/otter-creek-polonium df384dad45d4 (Bauer Precision's gallery: the black mount unscrewed, standing on its plug in front of the black Polonium's open rear and the tube clamp, seen from above, 800 x 800)","scaleRef":"the thread's own pitch, 24 to the inch by the sellers' 1.375x24","method":"about five crests show along the plug's near edge under the flange, with a relief above them; the view is from above and the last crests are in shadow","via":"harvest"},"note":"A rough count, two crests either way. Silencer Central's photo of the K's mount unscrewed, a view from the side, counts eight on what looks the same mount: that is the K's ledger's figure."}],"note":"Not seen once the mount is in: it sets only how far into the can the mount's own 1/2x28 thread is drawn before the hole runs on plain. The rear thread is the sellers' \"1.375x24\" (Capitol Armory: \"HUB-compatible 1.375x24 rear threads\")."}}},{"subject":"panzer-ar57-buffer","title":"Panzer Arms AR57 proprietary carbine buffer","dimensions":{"weight":{"label":"Weight (its class: carbine, H, H2…)","kind":"mass","measurements":[{"id":"review","value":4.8,"unit":"oz","pm":0.05,"stated":"You must put in the heavier buffer weight that ships with the gun. (4.8 ounces) vs the standard 3oz.","source":{"type":"spec","publisher":"review","name":"A buyer's review on Primary Arms' page for the AR57 16 in upper (Hoosier Carry, 2024-03-09, of the 12 in)","url":"https://www.primaryarms.com/panzer-arms-ar57-ultra-light-tactical-5-7x28mm-complete-upper-16in","retrieved":"2026-10-18","via":"harvest"}}],"note":"One buyer's figure, of the buffer that came with his 12 in upper (the 16 in's listing says the same buffer comes with it: \"Proprietary buffer weight and one 50 round magazine included\", Classic Firearms). Between an H2 (4.6 oz) and an H3 (5.4) as BCM states its own (bcm-h2-buffer, bcm-h3-buffer). No maker's or seller's figure is on file; Classic Firearms lists \"Proprietary buffer weight\" with none."},"length":{"label":"Length (the head's front face to the bumper's end)","kind":"length","measurements":[{"id":"std","value":3.251,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.carbine_buffer.length}","via":"harvest"},"note":"AN APPROXIMATION: the standard carbine buffer's length. No page gives this buffer's and no photo of it is on file; it goes in a carbine extension with the standard spring (Small Arms Review: \"fits any carbine AR15 lower\")."}]},"od":{"label":"Diameter (its head, which runs in the extension's bore)","kind":"length","measurements":[{"id":"std","value":0.98,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.carbine_buffer.head_d}","via":"harvest"},"note":"AN APPROXIMATION: the standard carbine buffer's head. It runs in a carbine extension's bore as every carbine buffer does."}]}}},{"subject":"panzer-ar57-ult-12-upper","title":"Panzer Arms AR57 ULT Complete AR-15 Upper Receiver - 5.7x28mm - 12\"","dimensions":{"weight":{"label":"Weight (as sold: its barrel, brake, handguard, bolt and handle; the magazine and buffer apart)","kind":"mass","measurements":[{"id":"center","value":3,"unit":"lb","pm":0.5,"stated":"Upper Weight ~3 lbs","source":{"type":"spec","publisher":"retailer","name":"AR Five Seven Center (ar-57center.com), home page: Cartridge 5.7×28mm NATO Capacity 50 Rounds Upper Weight ~3 lbs Full Build ~6 lbs Barrel Options 12″ / 16″","url":"https://www.ar-57center.com/","retrieved":"2026-10-18","via":"harvest"},"note":"One approximate figure for both barrel lengths."},{"id":"metal","value":49.4,"unit":"oz","pm":9,"source":{"type":"derived","basis":"The model's metal (2026-10-20: the lug's front, the handguard's underside and its lower rail read on their far edges, 49.7 before; 2026-10-19: the riser and the keel read narrower, the rail block's face cut back to where it stands and the latch added, its outline read through its camera, 51.0 before; detail pass, 2026-10-18: the handguard's chamfers and keel and the receiver's chamfer cut, the pocket moved to its middle plane; batch 10's 58.0 before them; the width read at 1.44 and this photo read through its own camera, 2026-10-18, 54.5 before that): the receiver with its rail block, the handle and the catch (15.88 cubic inches) and the handguard (7.11) in 7075 at std.density.aluminium_7075 (1.632 oz a cubic inch), the barrel, its brake and nut (2.61) in steel at std.density.steel (4.565): 25.9 + 11.6 + 11.9 oz. Over, by what the receiver's inside is: it is drawn solid round its bolt, and its opening down into the lower's well isn't drawn; the ± is that.","via":"harvest"}}],"adopt":{"from":"center","reason":"A published figure for the upper, if one for both lengths and approximate; the model's metal (drawn solid inside) is 0.1 lb over it and within the two figures' ±."},"note":"No page on file gives a weight for this upper alone; ar-57center.com gives one figure for the platform's upper."},"barrel_length":{"label":"Barrel length (the listing's own figure)","kind":"length","measurements":[{"id":"pa","value":12,"unit":"in","pm":0.5,"stated":"Barrel Length 12","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Panzer Arms AR57 ULT Complete AR-15 Upper Receiver - 5.7x28mm - 12\" (AR57ULT-12), Specifications","url":"https://www.primaryarms.com/ar57-ult-complete-upper-assembly-5-7-x28mm-12in","retrieved":"2026-10-18","via":"harvest"}},{"id":"kygunco","value":12,"unit":"in","pm":0.5,"stated":"Barrel Length 12\"","source":{"type":"spec","publisher":"retailer","name":"KYGUNCO, Panzer Arms AR57 ULT 12 inch Complete Upper (PNZ-AR57ULT-12), specifications","url":"https://www.kygunco.com/product/ar57-ar57ult-12-ult-5.7x28-12-upper-w-50rd-mag","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"pa","reason":"Both sellers give 12; Primary Arms' specifications table is the listing's own figure."}},"handguard_listed":{"label":"The handguard as the listing names it","kind":"length","measurements":[{"id":"pa","value":12,"unit":"in","pm":0.5,"stated":"Handguard 12 in Freefloat Rail","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, AR57ULT-12, Specifications","url":"https://www.primaryarms.com/ar57-ult-complete-upper-assembly-5-7-x28mm-12in","retrieved":"2026-10-18","via":"harvest"}}],"note":"What the 12 spans isn't said: the photo's handguard runs 10.6 in from its seam (6.84) to its front lip (17.45), and the receiver and handguard together 19.2 from the rail block's rear."},"muzzle_end_x":{"label":"The brake's front end ahead of the takedown pin","kind":"length","measurements":[{"id":"photo","value":19.58,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (the traced outline's x max (2101 px, the brake's prongs) on the brake's near side (0.31 in out)) through the camera fitted to it (the header): 19.86 in batch 10's pin frame.","via":"harvest"}}]},"muzzle_end_x_pinframe":{"label":"The brake's front end as the trace's frame reads it (the outline's map's other end: muzzle_end_x)","kind":"length","measurements":[{"id":"pinframe","value":19.681,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/panzer-ar57-ult-12-upper c261b4c5a32d (Primary Arms AR57ULT-12_02.jpg, the right side straight on, 2200 x 1467)","scaleRef":"its lug holes' near rims (takedown 243.5, 860.8; pivot 845.0, 864.5 px) as std.ar15.pin_spacing: 94.36 px/in","method":"the traced outline's x max (profiles.side), the brake's prongs at 2101 px","via":"harvest"}},{"id":"camera","value":19.58,"unit":"in","source":{"type":"derived","expr":"{.muzzle_end_x}","basis":"Since 2026-10-19 (night) the outline is read through the photo's camera, each stretch at its edge's depth (the seed's trace spec): its frame is the camera's, and the map is none.","via":"harvest"}}],"adopt":{"from":"camera","reason":"The trace reads the photo through its camera; the near rims' frame's reading (pinframe) is kept as it was read."}},"handguard_front_x_pinframe":{"label":"The handguard's front end as the trace's frame reads it (where the traced outline is clipped: the barrel, the nut and the brake are the model's)","kind":"length","measurements":[{"id":"pinframe","value":17.308,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/panzer-ar57-ult-12-upper c261b4c5a32d (Primary Arms AR57ULT-12_02.jpg, the right side straight on, 2200 x 1467)","scaleRef":"its lug holes' near rims (takedown 243.5, 860.8; pivot 845.0, 864.5 px) as std.ar15.pin_spacing: 94.36 px/in","method":"on a 3x crop the lip's front face meets the nut at 1877 px","via":"harvest"}},{"id":"camera","value":17.202,"unit":"in","source":{"type":"derived","expr":"{.handguard_front_x}","basis":"Since 2026-10-19 (night) the outline is read through the photo's camera, each stretch at its edge's depth (the seed's trace spec): its frame is the camera's, and the map is none.","via":"harvest"}}],"adopt":{"from":"camera","reason":"The trace reads the photo through its camera; the near rims' frame's reading (pinframe) is kept as it was read."}},"rail_slots":{"label":"How many slots the receiver's top rail has","kind":"count","measurements":[{"id":"photo","value":13,"unit":"count","source":{"type":"photo","photo":"references/panzer-ar57-ult-12-upper c261b4c5a32d","scaleRef":"none: a count","method":"thirteen dips in the tooth tops along the rail (every pixel from 110 to 645 px), on the standard's pitch in the pin frame (36.6 px) from 148.6 to 588.2 px","via":"harvest"}}]},"front_rail_slots":{"label":"How many slots each forward rail (on the front block's top, and under it) has","kind":"count","measurements":[{"id":"photo","value":3,"unit":"count","source":{"type":"photo","photo":"references/panzer-ar57-ult-12-upper c261b4c5a32d and 46e53e61437f","scaleRef":"none: a count","method":"three gaps between the front block's teeth along row 640 (1672-1675, 1709-1712, 1746-1749 px) and three under it along row 886; three slots on the top rail close from ahead in 46e53e61437f","via":"harvest"}},{"id":"pa-16","value":3,"unit":"count","stated":"13-slot Picatinny rail over the operating handle, plus 3-slot upper and lower forward rails","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, the 16 in AR57 ULT (ULT0116), Features: the 12 in's page doesn't list its rails","url":"https://www.primaryarms.com/panzer-arms-ar57-ultra-light-tactical-5-7x28mm-complete-upper-16in","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"photo","reason":"Counted on this upper; the 16 in's listing, the same receiver and rails, says the same."}},"rail_top_above_pin":{"label":"The rear rail's top above the pin line","kind":"length","measurements":[{"id":"photo","value":2.543,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (the tooth tops along row 624, read 2.541 at the first slot and 2.570 at the last (the photo's 0.36 degree lean between the pins, which the rails' tops don't share: the middle), at 367, 624 px) through the camera fitted to it (the header) on the rail's top flat's near edge (0.33 in out): 2.56 in batch 10's pin frame.","via":"harvest"}}]},"front_rail_top_above_pin":{"label":"The front block's rail top above the pin line","kind":"length","measurements":[{"id":"photo","value":2.55,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (the tooth tops at 633 px over 1675 to 1781 px, at 1724, 633 px) through the camera fitted to it (the header) on the rail's top flat's near edge (0.33 in out): 2.548 in batch 10's pin frame.","via":"harvest"}}]},"rail_slot0_x":{"label":"The rear rail's rearmost slot's centre ahead of the takedown pin (negative: behind it)","kind":"length","measurements":[{"id":"photo","value":-1.216,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (the camera's own fit: the thirteen slots' front edges on the rail's near face (the right ends of the gaps along rows 625 to 627 and 628 to 630, 153.8 to 595.4 px: 36.80 px apart), on MIL-STD-1913's pitch) through the camera fitted to it (the header): -1.15 in batch 10's pin frame.","via":"harvest"}}]},"rail_front_x":{"label":"The rear rail's front end (its front tooth's face)","kind":"length","measurements":[{"id":"photo","value":3.979,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (row 626's dark run ends at 628 px, at 628, 628 px) through the camera fitted to it (the header) on the rail's near face (0.4 in out): 4.007 in batch 10's pin frame.","via":"harvest"}}]},"rail_rear_x":{"label":"The rail block's rear end (the rail overhangs the receiver)","kind":"length","measurements":[{"id":"photo","value":-1.767,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (the traced outline's x min, at 94, 662 px, 2.11 above the pin line: the riser's rear end) through the camera fitted to it (the header) on the riser's side (riser_width / 2, 0.31 in out; at the rail's near face, 0.4 in out, before 2026-10-19: -1.715): -1.731 in batch 10's pin frame. The rail's head above it, on its own near edge, reads -1.72 to -1.74 (the traced outline).","via":"harvest"}}]},"rail_rear_x_pinframe":{"label":"The rail block's rear end as the trace's frame reads it (the outline's map behind the takedown pin: rail_rear_x)","kind":"length","measurements":[{"id":"pinframe","value":-1.594,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/panzer-ar57-ult-12-upper c261b4c5a32d (Primary Arms AR57ULT-12_02.jpg, the right side straight on, 2200 x 1467)","scaleRef":"its lug holes' near rims (takedown 243.5, 860.8; pivot 845.0, 864.5 px) as std.ar15.pin_spacing: 94.36 px/in","method":"the traced outline's x min","via":"harvest"},"note":"0.12 behind the camera's reading (rail_rear_x, -1.715; the 16 in's camera reads the same receiver's -1.725): the lens 23 in off reads a two-pin frame's scale differently at the rail's depth and across the part. The model scaled the outline behind the takedown pin by the two until 2026-10-19 (night), when the outline came to be read through the camera."},{"id":"camera","value":-1.767,"unit":"in","source":{"type":"derived","expr":"{.rail_rear_x}","basis":"Since 2026-10-19 (night) the outline is read through the photo's camera, each stretch at its edge's depth (the seed's trace spec): its frame is the camera's, and the map is none.","via":"harvest"}}],"adopt":{"from":"camera","reason":"The trace reads the photo through its camera; the near rims' frame's reading (pinframe) is kept as it was read."}},"rail_block_front_x":{"label":"The rear rail block's front face, flush with its rail's front end (the magazine's latch stands out of it)","kind":"length","measurements":[{"id":"photo","value":4.196,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (on a 3x crop the block's face at 645 px, where the magazine's rear end is, at 645, 673 px) through the camera fitted to it (the header) on the riser's or the keel's side (0.4175 in out): 4.193 in batch 10's pin frame.","via":"harvest"}},{"id":"camera","value":3.98,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d through the camera fitted to it (the header; 2026-10-19 (night), .cache/ar57-camera/pass3/): the face's near corner at the riser's side (riser_width / 2 out), where the lit face begins: 628.5 to 630.5 px along rows 634 to 652 (3.97 to 3.99), 628 px along rows 667 to 697 beside the latch (3.975 to 3.996). Above the magazine's top the lit face runs on to 645.5 to 646.6 px along rows 640 to 643, its far corner: a face 0.62 across at 3.97 puts the two corners there within a pixel (one 0.835 across, 3 to 5 px off).","via":"harvest"}}],"adopt":{"from":"camera","reason":"The face where it stands, read at its own edge's depth; the photo reading is the magazine's outline. The 16 in's photo, through its own camera, has 3.97."},"note":"2026-10-19 (night): the magazine's round end doesn't bear on this face. Through each upper's own camera the face stands 0.10 in behind the magazine's rearmost point (this upper's photo: 3.98 against 4.082; the 16 in's: 3.97 against 4.070), white between the two above and below the latch (latch_bottom_y, latch_top_y), which stands out of the face into the notch in the magazine's round end (fn-p90-50-magazine's own side photo, 76c0d7572a37, has the notch). The face is flush with the rail's front end (rail_front_x, 3.979). Batch 10's reading (photo) is the magazine's outline, where the trace took the magazine out: kept as read."},"front_rail_slot0_x":{"label":"The front block's top rail: its rearmost slot's centre","kind":"length","measurements":[{"id":"photo","value":15.187,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (the camera's own fit: the front rail's near edges (the left ends of its gaps along rows 637 to 640: 1670.1, 1707.5, 1744.3 px) and far edges (their right ends), on MIL-STD-1913's pitch) through the camera fitted to it (the header): 15.253 in batch 10's pin frame.","via":"harvest"}}]},"front_rail_front_x":{"label":"The front block's top rail: its front end","kind":"length","measurements":[{"id":"photo","value":16.247,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (its foremost tooth's face along row 640, 1781 px, at 1781, 650 px) through the camera fitted to it (the header) on the rail's near face (0.4 in out): 16.409 in batch 10's pin frame.","via":"harvest"}}]},"lower_rail_slot0_x":{"label":"The front block's lower rail: its rearmost slot's centre","kind":"length","measurements":[{"id":"photo","value":15.279,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (the gap's middle (1687 px, row 886) on the rail's near face, moved forward by what the same reading does on the front block's top rail (its gap's middle 15.113 through the camera against its near edges' 15.187)) through the camera fitted to it (the header): 15.414 in batch 10's pin frame.","via":"harvest"}}]},"lower_rail_bottom_y":{"label":"The lower forward rail's face (its tooth tops, facing down) above the pin line","kind":"length","measurements":[{"id":"photo","value":-0.153,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (the lowest dark row under the front block, 886 px, at 1723, 886 px) through the camera fitted to it (the header) on the rail's top flat's near edge (0.33 in out): -0.174 in batch 10's pin frame.","via":"harvest"}},{"id":"far-edge","value":-0.08,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"The same pixel (1723, 886) through the camera on the far edge of the rail's flat (0 - 0.328 out): its face seen from below (2026-10-20).","via":"harvest"}},{"id":"sixteen","value":-0.093,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{panzer-ar57-ult-16-upper.lower_rail_bottom_y}","basis":"The 16 in's photo through its own camera, from above, on the near edge of the rail's flat, its slots' depth the standard's: the same front block.","via":"harvest"}}],"adopt":{"from":"sixteen","reason":"This photo's two readings bracket it (-0.150 as the near edge, -0.080 as the far one, the silhouette from below); the 16 in's, from above, reads the edge its silhouette is."}},"receiver_rear_x":{"label":"The receiver's rear face behind the takedown pin (negative)","kind":"length","measurements":[{"id":"std","value":-0.621,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.ar15.upper_rear_face_x}","via":"harvest"},"note":"The standard's: an upper that fits a mil-spec lower stops ahead of its buffer tower."}]},"receiver_top_y":{"label":"The receiver's top at its rear, under the rail block's overhang, above the pin line","kind":"length","measurements":[{"id":"photo","value":1.524,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (profiles.side as traced: where its rear face turns back under the rail block's ramp, x -0.70 to -0.77, y 1.576 to 1.613, about 186, 713 px) through the camera fitted to it (the header) on the receiver's side set in above its chamfer (0.51 in out): 1.59 in batch 10's pin frame.","via":"harvest"}}]},"underside_y":{"label":"The receiver's underside above the pin line (it sits on the lower's deck)","kind":"length","measurements":[{"id":"std","value":0.2485,"unit":"in","pm":0.0015,"source":{"type":"derived","expr":"{std.ar15.deck_y}","via":"harvest"}},{"id":"photo","value":0.156,"unit":"in","pm":0.012,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (the traced outline's lower edge over x 2 to 5, about 842 px) through the camera fitted to it (the header) on the side face (0.72 in out): 0.222 in batch 10's pin frame.","via":"harvest"},"note":"0.09 under the deck: the receiver's near lower edge, from a lens 23 in off and 2.6 in under the pin line, read at the side face's depth (the deck is under the receiver's middle); the standard's is adopted"}],"adopt":{"from":"std","reason":"The seat is the lower's deck; the photo's reading is the near edge's."}},"tray_top_y":{"label":"The handguard's top (the magazine lies on it) above the pin line","kind":"length","measurements":[{"id":"photo","value":1.619,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (the outline's top under the magazine (the trace's cut, 712.7 px at u 1092) at the riser's width) through the camera fitted to it (the header): 1.65 in batch 10's pin frame.","via":"harvest"}},{"id":"seat","value":1.635,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{.mag_underside_y}","via":"harvest"},"note":"The magazine lies on it: one plane for both (a seat drawn bearing). The model clamps the traced outline's run under the magazine to it (the trace, cut along the magazine's underside on a slightly tilted photo, gives 1.638 at the rear to 1.665 at the front)."}],"adopt":{"from":"seat","reason":"The seat is the magazine's underside, read along its length on a 3x crop; the outline's top there is the cut the trace was made with. (Detail pass, 2026-10-18: batch 10 drew the magazine 0.016 to 0.028 in over the handguard's top.)"}},"tray_front_y":{"label":"The handguard's top at its lowest, where it ramps down ahead of the magazine's underside to the front block","kind":"length","measurements":[{"id":"photo","value":1.362,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (the lower edge of the light seen under the magazine's front end, 741 px at 1637 px, at 1612, 741 px) through the camera fitted to it (the header) on the top flat's edge (top_flat_width / 2, 0.4175 in out): 1.382 in batch 10's pin frame.","via":"harvest"}}]},"tray_dip_rear_x":{"label":"Where the handguard's top begins its ramp down to the front block","kind":"length","measurements":[{"id":"photo","value":13.551,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (where the light under the magazine's front end begins, 1527 px, at 1527, 720 px) through the camera fitted to it (the header) on the top flat's edge (top_flat_width / 2, 0.4175 in out): 13.68 in batch 10's pin frame.","via":"harvest"}}]},"front_block_rear_x":{"label":"The front block's rear face (the magazine's front cap stands against it)","kind":"length","measurements":[{"id":"photo","value":14.866,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (the cap's front edge, behind which the block's rear tooth begins, 1650 px, at 1650, 649 px) through the camera fitted to it (the header) on the rail's near face (0.4 in out): 15.004 in batch 10's pin frame.","via":"harvest"}}]},"takedown_lug_front_x":{"label":"The takedown lug's front face ahead of the takedown pin (the lug under the receiver, at the lower's rear slot)","kind":"length","measurements":[{"id":"camera","value":0.22,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d through the camera fitted to it (the header; 2026-10-20): the lug's front face, turned toward the lens (over x 11.4), shows as a band between its near edge (264.5 px, on the lug's near side: 0.216 to 0.225 along rows 850 to 860) and its far edge, the silhouette (286.6 px, on its far side: 0.216 to 0.226). Its rear face, the near edge, reads -0.22 (the outline): the lug 0.44 long, centred on its pin. The traced outline, read on the lug's near side, has its front at 0.46. The 16 in's photo through its own camera reads its front face's two edges 0.219 to 0.223.","via":"harvest"}}],"adopt":{"from":"camera","reason":"Both edges of the face agree, and the other upper's photo through its own camera reads the same; the model's lug is cut to it, the outline's front being the face's far edge read as its near one."}},"handguard_bottom_y":{"label":"The handguard's underside above the pin line","kind":"length","measurements":[{"id":"photo","value":0.058,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (the traced outline's lower edge over x 8 to 13.5 (0.049 to 0.062), at 1249, 862 px) through the camera fitted to it (the header) on the keel's side (keel_width / 2, 0.335 in out; at 0.4175, assumed until 2026-10-19: 0.048): 0.056 in batch 10's pin frame.","via":"harvest"}},{"id":"far-edge","value":0.135,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"The same pixel (1249, 862) through the camera on the keel's far side (0 - keel_width / 2): an underside seen from below, as from this lens 2.6 in under the pin line, shows its far edge (2026-10-20).","via":"harvest"}},{"id":"sixteen","value":0.098,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{panzer-ar57-ult-16-upper.handguard_bottom_y}","basis":"The 16 in's photo through its own camera, from a lens 0.57 above the pin line and 43 in off, where the silhouette is the underside's near edge: the same handguard section.","via":"harvest"}}],"adopt":{"from":"sixteen","reason":"This photo's two readings bracket it (the near edge 0.058, the far edge, the silhouette from below, 0.135); the 16 in's photo, from above, sees the edge its silhouette is, and from a lens twice as far. An underside seen from below shows its far edge, a face turned toward the lens its far edge, and a lens above a part sees an underside's near edge (2026-10-20: the 12 in's close photo, 2.6 in under the pin line, read both ways brackets this one's)."}},"handguard_front_x":{"label":"The handguard's front end (its lip round the barrel, where the brake's jam nut stands)","kind":"length","measurements":[{"id":"photo","value":17.202,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (the lip's front face meeting the nut (1877 px) at the keel's depth (0.42 in out), where the outline's map puts its clipped end within 0.035 (handguard_front_x_pinframe); at the side face's depth the same pixel is 17.125) through the camera fitted to it (the header): 17.451 in batch 10's pin frame.","via":"harvest"}}]},"side_face_bottom_y":{"label":"The height the model's seam ends at, low on the handguard's side (the lower chamfer's foot as batch 10 read it)","kind":"length","measurements":[{"id":"photo","value":0.26,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (the line along the handguard's lower part on a 3x crop, 843 px, at 1249, 843 px) through the camera fitted to it (the header) on the keel's side (keel_width / 2, 0.335 in out; at 0.4175, assumed until 2026-10-19: 0.251): 0.263 in batch 10's pin frame.","via":"harvest"}}],"note":"Batch 10 read this as the side face's foot; the detail pass (2026-10-18) read the section's lines down columns of the photo (lower_chamfer_top_y, keel_top_y): the side face ends higher, at 0.713, and this line is the lower chamfer's foot (keel_top_y reads it 0.243 down six columns). Kept for the seam's lean, which the model draws from it as it was."},"side_face_top_y":{"label":"The handguard's side face's upper edge, where the chamfer up to its top begins (above the pin line)","kind":"length","measurements":[{"id":"photo","value":1.26,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (luminance down columns 1000, 1120, 1240, 1300, 1420 and 1500 px (each the median of five): under the magazine's underside (712 px at 1240) a dark band, the chamfer facing up into the magazine's black underside, to 740.5 to 744.5 px across those columns, where the side face's grey (63) begins: 1.335 to 1.345, at 1240, 743 px) through the camera fitted to it (the header) on the side face (0.72 in out): 1.339 in batch 10's pin frame.","via":"harvest"}}],"note":"The section as the 16 in upper's ledger says (side_face_top_y there): a top flat, a chamfer down each side to a flat side face, a chamfer under it, and a keel; this one's own lines read on its own photo, its front ring seen from ahead and to the right in 46e53e61437f."},"receiver_chamfer_top_y":{"label":"The receiver's chamfer along its upper sides, under the rail block: its upper edge, where the receiver's side rises set in to the riser's foot (above the pin line)","kind":"length","measurements":[{"id":"photo","value":1.506,"unit":"in","pm":0.012,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (luminance down columns 282, 347 and 440 px (x 0.3, 1.0, 2.0): the face's grey (70 to 72) above, the band's (49 to 59) from 715.5 to 716 px down to 736.5 to 737.5 px, where the side face's (65 to 71) begins again: its top 1.565 to 1.571, its foot 1.337 to 1.342 (side_face_top_y's line on the handguard reads 1.339: one line), at 348, 716 px) through the camera fitted to it (the header) on the receiver's side set in above its chamfer (0.51 in out): 1.569 in batch 10's pin frame.","via":"harvest"}}],"note":"Detail pass, 2026-10-18: a band along the receiver's upper side from its rear face to a ramp under the rail block's window (receiver_chamfer_front_*), dark in the straight view as the handguard's chamfer is, lit from above in 0bde48a31171 and fe9d442f7b56 (a face turned up). Drawn as the handguard's chamfer's plane carried back to this height, the side above it set in to the deck at the riser's foot."},"receiver_chamfer_front_top_x":{"label":"That chamfer's front end, where it meets the face ahead of it, at receiver_chamfer_front_top_y (ahead of the takedown pin)","kind":"length","measurements":[{"id":"photo","value":3.69,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (along row 724 px: the band's dark (12 to 21) ends at 587.5 px, the face's grey (64 to 70) begins, at 588, 724 px) through the camera fitted to it (the header) on the receiver's chamfer (0.6 in out): 3.587 in batch 10's pin frame.","via":"harvest"}}]},"receiver_chamfer_front_top_y":{"label":"The height receiver_chamfer_front_top_x is read at","kind":"length","measurements":[{"id":"photo","value":1.42,"unit":"in","pm":0.006,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (row 724 px at that column, at 588, 724 px) through the camera fitted to it (the header) on the receiver's chamfer (0.6 in out): 1.494 in batch 10's pin frame.","via":"harvest"}}]},"receiver_chamfer_front_low_x":{"label":"That chamfer's front end lower down, at receiver_chamfer_front_low_y (ahead of the takedown pin): the end is a ramp","kind":"length","measurements":[{"id":"photo","value":3.557,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (along row 736 px: the band ends at 571.5 px; row 730 between (580 px, x 3.507 at 1.429) on the same line: the band's front end leans back going down, a ramp, at 572, 736 px) through the camera fitted to it (the header) on the receiver's chamfer (0.68 in out): 3.415 in batch 10's pin frame.","via":"harvest"}}]},"receiver_chamfer_front_low_y":{"label":"The height receiver_chamfer_front_low_x is read at","kind":"length","measurements":[{"id":"photo","value":1.278,"unit":"in","pm":0.006,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (row 736 px at that column, at 572, 736 px) through the camera fitted to it (the header) on the receiver's chamfer (0.68 in out): 1.364 in batch 10's pin frame.","via":"harvest"}}]},"lower_chamfer_top_y":{"label":"The handguard's side face's lower edge, where the chamfer under it begins (above the pin line)","kind":"length","measurements":[{"id":"photo","value":0.649,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (luminance down the same six columns: the side face's grey (58) drops to the chamfer's (32) at 798.5 to 803.5 px: 0.704 to 0.721, the lower row of M-LOK slots in the darker face below (see-through at 819 to 828 px at 1240), at 1240, 801 px) through the camera fitted to it (the header) on the side face (0.72 in out): 0.713 in batch 10's pin frame.","via":"harvest"}}]},"keel_top_y":{"label":"The lower chamfer's foot, where a short flat side (the keel, the lower block's width) runs down to the underside (above the pin line)","kind":"length","measurements":[{"id":"photo","value":0.241,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (luminance down the same six columns: the chamfer's 32 rises to the keel's 53 at 842.5 to 846.5 px (844.5 at 1240 px)) through the camera fitted to it (the header) on the keel's side (keel_width / 2, 0.335 in out; at 0.4175, assumed until 2026-10-19: 0.231): 0.243 in batch 10's pin frame.","via":"harvest"}}]},"lower_chamfer_run":{"label":"How far the lower chamfer runs in, across, from the side face to the keel","kind":"length","measurements":[{"id":"derived","value":0.385,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{.handguard_width} / 2 - {.keel_width} / 2","via":"harvest"},"note":"The keel's width read (keel_width), 2026-10-19 (night); it had been taken to be the riser's."}]},"lower_chamfer_drop":{"label":"How far the lower chamfer drops, from the side face's foot to the keel","kind":"length","measurements":[{"id":"derived","value":0.408,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.lower_chamfer_top_y} - {.keel_top_y}","via":"harvest"}}]},"lower_face_angle":{"label":"The lower chamfers' faces: where their normal points, about +x from the top (90 is the right side)","kind":"angle","measurements":[{"id":"derived","value":133.34,"unit":"deg","pm":4,"source":{"type":"derived","basis":"90 degrees + atan(lower_chamfer_run / lower_chamfer_drop) = 90 + atan(0.385 / 0.408): the chamfer's normal, from the read heights, the read width and the read keel; the ± is the run's.","via":"harvest"}}],"note":"The expressions have no arctangent: the value is written as worked out, 90 + atan(lower_chamfer_run / lower_chamfer_drop), and the part's test holds it to its inputs."},"mlok_lower_z":{"label":"The lower row's slots' centres on the lower chamfer: how far out of the centre plane","kind":"length","measurements":[{"id":"derived","value":0.5709,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.handguard_width} / 2 - ({.lower_chamfer_top_y} - {.mlok_lower_y}) * {.lower_chamfer_run} / {.lower_chamfer_drop}","via":"harvest"}}]},"mlok_lower_axis_y":{"label":"The lower row's anchor: on the centre plane where the line square to the lower chamfer through a slot's centre meets it (above the pin line)","kind":"length","measurements":[{"id":"derived","value":1.0297,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{.mlok_lower_y} + {.mlok_lower_z} * {.lower_chamfer_run} / {.lower_chamfer_drop}","via":"harvest"}}]},"mlok_lower_face_distance":{"label":"The lower chamfer's surface from the lower row's anchor, along its normal","kind":"length","measurements":[{"id":"derived","value":0.785,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{.mlok_lower_z} * sqrt(1 + ({.lower_chamfer_run} / {.lower_chamfer_drop}) * ({.lower_chamfer_run} / {.lower_chamfer_drop}))","via":"harvest"}}]},"handguard_rear_x":{"label":"The handguard's rear edge on the receiver's side (the seam), at its middle","kind":"length","measurements":[{"id":"photo","value":6.915,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (on a 3x crop the edge runs from 860 px under the magazine to 920 px at the side face's foot: the middle, at 890, 775 px) through the camera fitted to it (the header) on the side face (0.72 in out): 6.84 in batch 10's pin frame.","via":"harvest"}}]},"handguard_rear_top_x":{"label":"The seam at the handguard's top","kind":"length","measurements":[{"id":"photo","value":6.589,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (its upper end, 860 px at 727 px, at 861, 732 px) through the camera fitted to it (the header) on the side face (0.72 in out): 6.52 in batch 10's pin frame.","via":"harvest"}}]},"handguard_rear_bottom_x":{"label":"The seam at the side face's foot","kind":"length","measurements":[{"id":"photo","value":7.246,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (its lower end, 920 px at 830 px, at 920, 836 px) through the camera fitted to it (the header) on the side face (0.72 in out): 7.16 in batch 10's pin frame.","via":"harvest"}}]},"front_block_face_x":{"label":"The front block's rear face at the magazine's body's height, where the cap's body stands against it (ahead of the takedown pin); the rail's rear tooth reaches further back over the magazine's top (front_block_rear_x)","kind":"length","measurements":[{"id":"photo","value":14.96,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (along rows 650 to 690 the cap's grey ends at 1668.5 to 1670 px: the cap's front edge on its near side (fn-p90-50-magazine.cap_width / 2 out), where it stands against the block; from behind the block (the lens's foot is at x 11) the cap's near side covers the riser's) through the camera fitted to it (the header): 15.205 in batch 10's pin frame.","via":"harvest"}},{"id":"seat","value":14.951,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{.mag_rear_x} + {fn-p90-50-magazine.length}","via":"harvest"},"note":"Where the magazine's cap stands, its rear end on the latch: the face drawn bearing on it (a seat is drawn bearing)."}],"adopt":{"from":"seat","reason":"The magazine (fn-p90-50-magazine.length, its two ends through both uppers' cameras) stands with its cap against this face and its round end on the latch: the face is drawn where its cap stands, 0.01 in behind the cap's front edge read through this photo's camera (photo)."},"note":"Detail pass, 2026-10-18, the magazine's owner's reading checked on the photo: front_block_rear_x (1650 px) is where the cap's lug's dark face begins at the rail's height; at the body's height the cap is lit to 1668.5 to 1670 px and the block dark from there. The room between the blocks is then 11.01 in (the 16 in's photo: 11.09). The photo is a close one (the pocket's note): an edge nearer the lens than the middle plane reads up to 0.1 in forward here; not corrected, the edge's depth not being known."},"bore_axis_above_pin":{"label":"Bore axis above the takedown pin centre","kind":"length","measurements":[{"id":"photo","value":0.951,"unit":"in","pm":0.025,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (the middle of the brake's silhouette (758 to 818 px) in columns 2030 to 2050) through the camera fitted to it (the header) on the bore's vertical plane (0.0 in out): 0.893 in batch 10's pin frame.","via":"harvest"},"note":"0.006 under the 16 in photo's reading on its barrel (0.957): batch 10's 0.893 in the pin frame of the holes' see-through middles was 0.064 under it"}]},"brake_od":{"label":"The brake's diameter","kind":"length","measurements":[{"id":"photo","value":0.625,"unit":"in","pm":0.025,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (58 px (760 to 818) in column 2040) through the camera fitted to it (the header): 0.624 in batch 10's pin frame.","via":"harvest"}}]},"nut_rear_x":{"label":"The brake's hex jam nut: its rear face (against the handguard's lip)","kind":"length","measurements":[{"id":"photo","value":17.221,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (a 3x crop: the nut's rear at 1877 px, at 1877, 787 px) through the camera fitted to it (the header) on the nut's near side (0.36 in out): 17.451 in batch 10's pin frame.","via":"harvest"}}]},"brake_rear_x":{"label":"The brake's rear face (in front of its jam nut) ahead of the takedown pin","kind":"length","measurements":[{"id":"photo","value":17.444,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (a 3x crop: the nut's front and the brake's rear at 1897 px, at 1897, 788 px) through the camera fitted to it (the header) on the brake's near side, or the face the front block's holes are in (0.31 in out): 17.666 in batch 10's pin frame.","via":"harvest"}}]},"nut_height":{"label":"The jam nut's height as it shows from the side (a hex: across its corners or its flats, as it stands)","kind":"length","measurements":[{"id":"photo","value":0.722,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (a 3x crop: 753 to 820 px) through the camera fitted to it (the header): 0.72 in batch 10's pin frame.","via":"harvest"}}]},"brake_band_front_x":{"label":"The brake's rear band: its front end, where a groove parts it from the ported body","kind":"length","measurements":[{"id":"photo","value":17.926,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (a 3x crop: the groove at 1943 px, at 1943, 788 px) through the camera fitted to it (the header) on the brake's near side, or the face the front block's holes are in (0.31 in out): 18.161 in batch 10's pin frame.","via":"harvest"}}]},"brake_port_x":{"label":"The brake's rearmost column of ports: its centre","kind":"length","measurements":[{"id":"photo","value":18.319,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (a 3x crop: the columns at 1980, 2005 and 2030 px, at 1980, 788 px) through the camera fitted to it (the header) on the ports' near side (0.29 in out): 18.559 in batch 10's pin frame.","via":"harvest"}}]},"brake_port_pitch":{"label":"The ports' columns, centre to centre","kind":"length","measurements":[{"id":"photo","value":0.262,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (25 px apart) through the camera fitted to it (the header): 0.269 in batch 10's pin frame.","via":"harvest"}}]},"brake_port_d":{"label":"A port's diameter","kind":"length","measurements":[{"id":"photo","value":0.156,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (about 15 px across on a 3x crop) through the camera fitted to it (the header): 0.16 in batch 10's pin frame.","via":"harvest"}}]},"brake_port_columns":{"label":"How many columns of ports along the brake","kind":"count","measurements":[{"id":"photo","value":3,"unit":"count","source":{"type":"photo","photo":"references/panzer-ar57-ult-12-upper c261b4c5a32d","scaleRef":"none: a count","method":"three along each row (c261b4c5a32d) and from ahead (46e53e61437f)","via":"harvest"}}]},"brake_ports_around":{"label":"How many ports round the brake in each column","kind":"count","measurements":[{"id":"photo","value":6,"unit":"count","source":{"type":"photo","photo":"references/panzer-ar57-ult-12-upper c261b4c5a32d","scaleRef":"none: a count","method":"two rows on the half facing the lens, at 770 and 798 px about the brake's axis at 788 px (radius 29 px): 37 degrees above the right side's middle and 19.5 below, 56.5 apart: six round, one every 60 degrees; the far half inferred","via":"harvest"}}]},"brake_port_phase":{"label":"Where the ports are clocked: degrees from the left side's middle toward the top, a row every 60","kind":"count","measurements":[{"id":"photo","value":19.5,"unit":"count","source":{"type":"photo","photo":"references/panzer-ar57-ult-12-upper c261b4c5a32d","scaleRef":"none: an angle on the brake's own radius","method":"the row 19.5 degrees under the right side's middle (asin(10 / 29)) is 199.5 degrees from the left side's: 19.5 modulo 60","via":"harvest"},"note":"Degrees, held as a count."}]},"brake_slot_depth":{"label":"The slot across the brake's front end: how deep it runs back from the front","kind":"length","measurements":[{"id":"photo","value":0.477,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (light through the front end along row 790 from 2056 px to the front, 2101 px) through the camera fitted to it (the header): 0.484 in batch 10's pin frame.","via":"harvest"}}]},"brake_slot_width":{"label":"The slot's height (it runs across, side to side)","kind":"length","measurements":[{"id":"photo","value":0.204,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (19 px (780 to 799) in column 2060) through the camera fitted to it (the header): 0.204 in batch 10's pin frame.","via":"harvest"}}]},"mlok_upper_slots":{"label":"M-LOK slots in the upper row on each side","kind":"count","measurements":[{"id":"photo","value":6,"unit":"count","source":{"type":"photo","photo":"references/panzer-ar57-ult-12-upper c261b4c5a32d","scaleRef":"none: a count","method":"six dark slots along row 773 (centres 1038, 1190, 1342, 1494, 1646 and 1778 px)","via":"harvest"}}]},"mlok_lower_slots":{"label":"M-LOK slots in the lower row on each side","kind":"count","measurements":[{"id":"photo","value":5,"unit":"count","source":{"type":"photo","photo":"references/panzer-ar57-ult-12-upper c261b4c5a32d","scaleRef":"none: a count","method":"five see-through slots along row 827 (centres 1113, 1258.5, 1404, 1551, 1697.5 px)","via":"harvest"}}]},"mlok_upper_front_x":{"label":"The upper row's foremost slot's centre ahead of the takedown pin","kind":"length","measurements":[{"id":"photo","value":16.328,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (the camera's own fit: the upper row's five whole slots (their dark runs' middles along rows 762 to 764 and 769 to 771: 1039.1, 1189.9, 1341.6, 1493.75, 1646.4 px) on Magpul's 40 mm pitch on the side face; the foremost slot, partly under the front block, is one pitch ahead of the last of them) through the camera fitted to it (the header): 16.4 in batch 10's pin frame.","via":"harvest"}}]},"mlok_lower_front_x":{"label":"The lower row's foremost slot's centre ahead of the takedown pin","kind":"length","measurements":[{"id":"photo","value":15.389,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (the see-through slots' middles along row 827 (1113, 1258.5, 1404, 1551, 1697.5 px) with half the far chamfer's slot's shift toward the lens's foot taken off: the near slots' centres 9.111, 10.677, 12.235, 13.814, 15.389 (1.570 apart on average, Magpul's 1.575)) through the camera fitted to it (the header): 15.523 in batch 10's pin frame.","via":"harvest"}}]},"mlok_upper_y":{"label":"The upper row's centre line above the pin line","kind":"length","measurements":[{"id":"photo","value":0.984,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (its slots between 760 and 787 px, at 1649, 772 px) through the camera fitted to it (the header) on the side face (0.72 in out): 1.048 in batch 10's pin frame.","via":"harvest"}}]},"mlok_lower_y":{"label":"The lower row's centre line above the pin line","kind":"length","measurements":[{"id":"photo","value":0.491,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (the see-through slots' middle row (827 px) with half the far chamfer's slot's vertical shift (13.4 px, toward the lens's foot, below) taken off, on the lower chamfer (0.56 in out)) through the camera fitted to it (the header): 0.462 in batch 10's pin frame.","via":"harvest"}}]},"mag_rear_x":{"label":"The seated magazine's rear end ahead of the takedown pin","kind":"length","measurements":[{"id":"photo","value":4.101,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (its round end's outline at 644.5 px (row 670): the end a half circle in plan as wide as the magazine (fn-p90-50-magazine.width), the line of sight tangent to it a little nearer the lens than its rearmost point) through the camera fitted to it (the header): 4.195 in batch 10's pin frame.","via":"harvest"},"note":"At the latch's height: the latch's lit rim stands beside the magazine's end there."},{"id":"above-latch","value":4.082,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d through the camera fitted to it (the header; 2026-10-19 (night), .cache/ar57-camera/pass3/magend.py): the round end's outline where it stands against the rail block's lit face, above the latch: 643.6 to 643.8 px along rows 650 to 662, as the half circle in plan it is (fn-p90-50-magazine.width), the line of sight tangent to it 0.26 in nearer the lens than its rearmost point: 4.077 to 4.087.","via":"harvest"}}],"adopt":{"from":"above-latch","reason":"Row 670 (photo) is at the latch's height, where the latch's lit rim stands beside the magazine's end; above it the end stands against the block's lit face. The 16 in's photo, through its own camera, has 4.070 for the same seat."}},"latch_bottom_y":{"label":"The magazine's latch, out of the rear rail block's front face into the notch in the magazine's round end: its underside above the pin line","kind":"length","measurements":[{"id":"camera","value":1.76,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d through the camera fitted to it (the header; 2026-10-19 (night)): the dark lobe between the block's face and the magazine's round end, beside the face's near corner (628 px), from row 666.5 to 697.5: its foot at 1.763 on the face's near corner (riser_width / 2 out). The 16 in's photo has it from 1.78 to 2.12.","via":"harvest"}}]},"latch_top_y":{"label":"The magazine's latch: its top above the pin line","kind":"length","measurements":[{"id":"camera","value":2.1,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d as latch_bottom_y: its top at row 666.5, 2.100.","via":"harvest"}}]},"latch_width":{"label":"The magazine's latch: across","kind":"length","measurements":[{"id":"assumed","value":0.62,"unit":"in","pm":0.1,"source":{"type":"derived","expr":"{.riser_width}","basis":"An assumption for the drawing, not a reading: no view shows it across. In the 12 in's photo its near side stands at the face's near corner (a dark strip, 627 to 632 px, beside the lit face): drawn as wide as the face it stands out of.","via":"harvest"}}]},"mag_underside_y":{"label":"The seated magazine's underside (its body's flat bottom, lying on the handguard's top) above the pin line","kind":"length","measurements":[{"id":"photo","value":1.635,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (the line under the magazine at 711 px (u 1092): from a lens 2.6 in under the pin line the magazine's underside shows as a band down to where the handguard's top edge hides it, so the line is that edge, at the top flat's edge) through the camera fitted to it (the header) (top_flat_width / 2, 0.4175 in out): 1.666 in batch 10's pin frame.","via":"harvest"},"note":"0.035 over the 16 in photo's 1.600 for the same seat (batch 10's pin frame had 0.1 over its 1.572)"}]},"feed_pocket_x":{"label":"The round pocket the magazine's feed tower sits in: its centre ahead of the takedown pin","kind":"length","measurements":[{"id":"photo","value":5.162,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (the middle of the notch the tower shows through (653 to 793 px: 723 px) on the side face (0.72 in out), the tower's centre being the notch's) through the camera fitted to it (the header): 5.037 in batch 10's pin frame.","via":"harvest"}},{"id":"mid-plane","value":5.19,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"The photo reading moved from the near wall, where the notch's ends are, to the pocket's middle plane, the plane the pins' frame reads true in (detail pass, 2026-10-18). The photo is a close one: on its near side face the upper M-LOK row's five centres read 1.635 apart for the standard's 1.575 (3.8% over), while the lower row's see-through centres, set by the slots of both walls together, read the standard's (1.572): the near face is magnified 1.038 about the lens's axis (a lens about 20 in off, 0.75 in nearer than the middle). About the image's middle (1100 px, 9.10 in ahead of the takedown pin), 9.10 + (5.037 - 9.10) / 1.038 = 5.186. The ± is the magnification's spread and the lens's axis taken at the image's middle (a cropped photo's may not be).","via":"harvest"},"note":"The magazine's tower is concentric with its round rear end (fn-p90-50-magazine.width / 2 ahead of it): mag_rear_x + 0.97 = 5.165, 0.02 from this; the photo reading as it stood had the tower 0.14 ahead of the pocket."},{"id":"tower","value":5.056,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.mag_rear_x} + {fn-p90-50-magazine.width} / 2","via":"harvest"},"note":"Where the magazine's tower stands: concentric with its round end (US 4,905,394's FIG. 3 and FIG. 4; the magazine's own side photo has the tower flush with its rear end within a pixel), the round end against the rail block. No view on file shows the pocket from above."}],"adopt":{"from":"tower","reason":"The pocket holds the magazine's tower, so it is drawn round it. The notch the tower shows through in the near wall reads 5.162 through the photo's camera (5.065 in the trace's frame) (photo): a chord whose two ends lie at two depths of a wall seen from a lens off to one side, ahead of the tower's place by 0.09; both are kept, and the magazine's own photo (the tower concentric with the round end) decides it."}},"feed_notch_length":{"label":"The notch in each wall the magazine's feed tower shows through: its length","kind":"length","measurements":[{"id":"photo","value":1.462,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (653 to 793 px on a 3x crop, the wall dark either side) through the camera fitted to it (the header): 1.506 in batch 10's pin frame.","via":"harvest"}}]},"feed_pocket_floor_y":{"label":"The pocket's floor (the tower's underside) above the pin line","kind":"length","measurements":[{"id":"photo","value":1.063,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (the tower's lower edge on a 3x crop, 757 px, at 723, 757 px) through the camera fitted to it (the header) on the side face (0.72 in out): 1.149 in batch 10's pin frame.","via":"harvest"}}]},"window_rear_x":{"label":"The rail block's window for the handle (the larger, foremost of two): its rear end","kind":"length","measurements":[{"id":"photo","value":2.946,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (on a 5x crop 531 px; the lever stands in it from the right, at 531, 680 px) through the camera fitted to it (the header) on the riser's side (riser_width / 2, 0.31 in out; at 0.4175, assumed until 2026-10-19: 2.986): 2.968 in batch 10's pin frame.","via":"harvest"}}]},"window_front_x":{"label":"The handle's window: its front end","kind":"length","measurements":[{"id":"photo","value":3.544,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (on a 5x crop 587 px, at 587, 681 px) through the camera fitted to it (the header) on the riser's side (riser_width / 2, 0.31 in out; at 0.4175, assumed until 2026-10-19: 3.581): 3.568 in batch 10's pin frame.","via":"harvest"}}]},"window2_rear_x":{"label":"The second, smaller window behind it: its rear end","kind":"length","measurements":[{"id":"photo","value":2.292,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (on a 5x crop 470 px, at 470, 680 px) through the camera fitted to it (the header) on the riser's side (riser_width / 2, 0.31 in out; at 0.4175, assumed until 2026-10-19: 2.335): 2.312 in batch 10's pin frame.","via":"harvest"}}]},"window2_front_x":{"label":"The second window: its front end","kind":"length","measurements":[{"id":"photo","value":2.601,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (on a 5x crop 499 px, at 499, 680 px) through the camera fitted to it (the header) on the riser's side (riser_width / 2, 0.31 in out; at 0.4175, assumed until 2026-10-19: 2.643): 2.622 in batch 10's pin frame.","via":"harvest"}}]},"window_bottom_y":{"label":"The two windows' bottom edge above the pin line","kind":"length","measurements":[{"id":"photo","value":1.758,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (on a 5x crop 697 px, at 534, 697 px) through the camera fitted to it (the header) on the riser's side (riser_width / 2, 0.31 in out; at 0.4175, assumed until 2026-10-19: 1.737): 1.779 in batch 10's pin frame.","via":"harvest"}}]},"window_top_y":{"label":"The two windows' top edge above the pin line","kind":"length","measurements":[{"id":"photo","value":2.131,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (on a 5x crop 663 px, at 534, 663 px) through the camera fitted to it (the header) on the riser's side (riser_width / 2, 0.31 in out; at 0.4175, assumed until 2026-10-19: 2.109): 2.148 in batch 10's pin frame.","via":"harvest"}}]},"catch_rear_x":{"label":"The magazine catch's lever where it stands out of the window on the right: its rear face","kind":"length","measurements":[{"id":"photo","value":2.9,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (on a 5x crop 513 px, at 513, 668 px) through the camera fitted to it (the header) on the side face (0.72 in out): 2.774 in batch 10's pin frame.","via":"harvest"}}]},"catch_front_x":{"label":"The lever's front face","kind":"length","measurements":[{"id":"photo","value":3.16,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (on a 5x crop 538 px, at 538, 668 px) through the camera fitted to it (the header) on the side face (0.72 in out): 3.04 in batch 10's pin frame.","via":"harvest"}}]},"catch_bottom_y":{"label":"The lever's lower end above the pin line","kind":"length","measurements":[{"id":"photo","value":1.799,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (on a 5x crop 686 px, at 525, 686 px) through the camera fitted to it (the header) on the side face (0.72 in out): 1.899 in batch 10's pin frame.","via":"harvest"}}]},"catch_top_y":{"label":"The lever's upper end above the pin line (it stands up over the window's top)","kind":"length","measurements":[{"id":"photo","value":2.185,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (on a 5x crop 650 px, at 525, 650 px) through the camera fitted to it (the header) on the side face (0.72 in out): 2.287 in batch 10's pin frame.","via":"harvest"}}]},"cross_hole_y":{"label":"The row of blind holes along the rail block's side, under its slots: their centres above the pin line","kind":"length","measurements":[{"id":"photo","value":2.27,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (on a 5x crop at 650 px, under each slot (438, 474, 511, 548, 585 px: 36.75 apart), at 488, 650 px) through the camera fitted to it (the header) on the riser's side (riser_width / 2, 0.31 in out; at 0.4175, assumed until 2026-10-19: 2.247): 2.286 in batch 10's pin frame.","via":"harvest"}}]},"cross_hole_d":{"label":"Those holes' diameter","kind":"length","measurements":[{"id":"photo","value":0.171,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (16 px across on a 5x crop, on the riser's side) through the camera fitted to it (the header): 0.172 in batch 10's pin frame.","via":"harvest"},"note":"0.125 on the 16 in's photo (10 px at 80 px/in): each its own"}]},"front_hole_x":{"label":"The front block's five holes: the rearmost's centre","kind":"length","measurements":[{"id":"photo","value":15.139,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (on a 3x crop the five at 1675, 1698, 1723, 1748 and 1773 px, at 1675, 663 px) through the camera fitted to it (the header) on the brake's near side, or the face the front block's holes are in (0.31 in out): 15.27 in batch 10's pin frame.","via":"harvest"}}]},"front_hole_pitch":{"label":"The front block's holes, centre to centre","kind":"length","measurements":[{"id":"photo","value":0.2653,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (the five rings' centres 25.0 px apart, 1674.3 to 1774.4 px, 2026-10-19, at the riser's side; 24.5 px by eye before, 0.2597) through the camera fitted to it (the header): 0.2635 in batch 10's pin frame.","via":"harvest"}}]},"front_hole_y":{"label":"The front block's holes: their centres above the pin line","kind":"length","measurements":[{"id":"photo","value":2.23,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (663 px, at 1724, 663 px) through the camera fitted to it (the header) on the brake's near side, or the face the front block's holes are in (0.31 in out): 2.227 in batch 10's pin frame.","via":"harvest"}}]},"lower_hole_x":{"label":"The lower block's five holes: the rearmost's centre","kind":"length","measurements":[{"id":"photo","value":15.326,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (on a 3x crop the five at 1697, 1727, 1757, 1787 and 1817 px, at 1697, 857 px) through the camera fitted to it (the header) on the keel's side (keel_width / 2, 0.335 in out; at 0.4175, assumed until 2026-10-19: 15.312): 15.52 in batch 10's pin frame.","via":"harvest"}}]},"lower_hole_pitch":{"label":"The lower block's holes, centre to centre","kind":"length","measurements":[{"id":"photo","value":0.3174,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (the five rings' centres 30.4 px apart, 1695.6 to 1817.3 px, 2026-10-19, at the keel's side; 30 px by eye before, 0.3116) through the camera fitted to it (the header): 0.3225 in batch 10's pin frame.","via":"harvest"}}]},"lower_hole_y":{"label":"The lower block's holes: their centres above the pin line","kind":"length","measurements":[{"id":"photo","value":0.157,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (857 px, at 1760, 857 px) through the camera fitted to it (the header) on the keel's side (keel_width / 2, 0.335 in out; at 0.4175, assumed until 2026-10-19: 0.147): 0.143 in batch 10's pin frame.","via":"harvest"}}]},"handguard_width":{"label":"The handguard's width across its side faces (the receiver's too: one figure)","kind":"length","measurements":[{"id":"sixteen","value":1.44,"unit":"in","source":{"type":"derived","expr":"{panzer-ar57-ult-16-upper.handguard_width}","basis":"The 16 in upper's (its ledger says what it rests on: a camera fitted to this upper's own three-quarter view from ahead, 46e53e61437f, and one to the 16 in's from behind, 0bde48a31171): the same receiver and handguard section, one figure for both.","via":"harvest"}}]},"riser_width":{"label":"The riser under each rail block's rail head (the face the rows of blind holes are in), across","kind":"length","measurements":[{"id":"assumed","value":0.835,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading (batch 10 to 2026-10-19): the riser as wide as the rail's head (std.picatinny.top_width), its sides taken to run down from the head with no step in the 16 in's views from behind (fe9d442f7b56, 0bde48a31171).","via":"harvest"}},{"id":"camera","value":0.62,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"Read through cameras fitted to two views of this upper from ahead (2026-10-19 (night), .cache/ar57-camera/pass3/fit4d.py, fitW2.py): each blind hole a ray from this upper's straight view's camera (the header; the dark ring's centre there) and its rim's centre in the other view, the depth along the rays one figure a row, left to the fit. 4d5581786e3d (from ahead, right and above, the whole upper; 0.67 px rms): its front rail's six slot edges and its receiver rail's twenty-six on MIL-STD-1913's pitch, the front rail's top flat's near and far edges and its head's widest, and three rows of holes: the front block's row 0.314 ± 0.005 out of the centre plane (0.303 to 0.326 with the rail's lines left out in turn), the rear block's row under its thirteen slots 0.316 ± 0.021. 46e53e61437f (the front block close, handguard_width's camera with the holes' depth left free): 0.310. Under each block's head the riser shows as a strip with the holes in it, the head (0.835) overhanging it; the rear block's face runs on down from the strip with a hairline between, the front block's below a dark band. Checked on the rail block's front face in the straight view (rail_block_front_x): 0.62 across puts its two corners where they show within a pixel, 0.835 3 to 5 px off.","via":"harvest"}}],"adopt":{"from":"camera","reason":"Three rows of holes through two cameras, over an assumption; the head's overhang shows on both blocks in 4d5581786e3d."}},"keel_width":{"label":"The keel under the lower chamfers (the lower block's side, the face its row of blind holes is in), across","kind":"length","measurements":[{"id":"camera","value":0.67,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"Read through the camera fitted to 4d5581786e3d as riser_width is (2026-10-19 (night)): the lower block's row of five blind holes 0.335 ± 0.008 out of the centre plane (0.334 to 0.340 with the rails' lines left out in turn). In the straight view the keel's strip (keel_top_y to the underside) runs from the seam to the lower block with the holes in it, and the lower rail's head (0.835) overhangs it there.","via":"harvest"}}]},"top_flat_width":{"label":"The handguard's top flat under the magazine (between the two upper chamfers), across","kind":"length","measurements":[{"id":"assumed","value":0.835,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the flat is under the magazine (1.95 across) in every view on file. Drawn as it was drawn (as wide as the rail's head, std.picatinny.top_width) when it was taken to be the riser's width, until 2026-10-19. The front block's lower face's edge (y 1.54, 0.46 to 0.50 out through 46e53e61437f's and 4d5581786e3d's cameras) and the side face's top (side_face_top_y) put that chamfer's plane, carried up to the tray, 0.74 to 0.85 across.","via":"harvest"}}]},"handguard_wall":{"label":"The handguard's wall","kind":"length","measurements":[{"id":"assumed","value":0.12,"unit":"in","source":{"type":"derived","expr":"{panzer-ar57-ult-16-upper.handguard_wall}","basis":"An assumption for the drawing, not a reading: the same assumption as the 16 in upper's (its ledger says what it rests on): no view of this one gives it either.","via":"harvest"}}]},"lug_clearance":{"label":"Each lug's clearance to the lower's slot it stands in, per side","kind":"length","measurements":[{"id":"assumed","value":0.005,"unit":"in","source":{"type":"derived","expr":"{panzer-ar57-ult-16-upper.lug_clearance}","basis":"An assumption for the drawing, not a reading: the same assumption as the 16 in upper's (its ledger says what it rests on): no view of this one gives it either.","via":"harvest"}}]},"catch_out":{"label":"How far the lever stands out of the rail block's right side","kind":"length","measurements":[{"id":"assumed","value":0.3,"unit":"in","source":{"type":"derived","expr":"{panzer-ar57-ult-16-upper.catch_out}","basis":"An assumption for the drawing, not a reading: the same assumption as the 16 in upper's (its ledger says what it rests on): no view of this one gives it either.","via":"harvest"}}]},"cross_hole_depth":{"label":"How deep the blind holes go","kind":"length","measurements":[{"id":"assumed","value":0.1,"unit":"in","source":{"type":"derived","expr":"{panzer-ar57-ult-16-upper.cross_hole_depth}","basis":"An assumption for the drawing, not a reading: the same assumption as the 16 in upper's (its ledger says what it rests on): no view of this one gives it either.","via":"harvest"}}]},"bolt_end_d":{"label":"The bolt's round rear end, as it shows in the receiver's rear face","kind":"length","measurements":[{"id":"assumed","value":0.75,"unit":"in","source":{"type":"derived","expr":"{panzer-ar57-ult-16-upper.bolt_end_d}","basis":"An assumption for the drawing, not a reading: the same assumption as the 16 in upper's (its ledger says what it rests on): no view of this one gives it either.","via":"harvest"}}]},"bolt_end_proud":{"label":"How far the bolt's end stands out of the rear face","kind":"length","measurements":[{"id":"assumed","value":0.05,"unit":"in","source":{"type":"derived","expr":"{panzer-ar57-ult-16-upper.bolt_end_proud}","basis":"An assumption for the drawing, not a reading: the same assumption as the 16 in upper's (its ledger says what it rests on): no view of this one gives it either.","via":"harvest"}}]},"brake_groove_w":{"label":"The groove between the brake's rear band and its ported body: its width","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","source":{"type":"derived","expr":"{panzer-ar57-ult-16-upper.brake_groove_w}","basis":"An assumption for the drawing, not a reading: the same assumption as the 16 in upper's (its ledger says what it rests on): no view of this one gives it either.","via":"harvest"}}]},"brake_groove_depth":{"label":"That groove's depth","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","source":{"type":"derived","expr":"{panzer-ar57-ult-16-upper.brake_groove_depth}","basis":"An assumption for the drawing, not a reading: the same assumption as the 16 in upper's (its ledger says what it rests on): no view of this one gives it either.","via":"harvest"}}]},"width":{"label":"The receiver's width","kind":"length","measurements":[{"id":"derived","value":1.44,"unit":"in","source":{"type":"derived","expr":"{.handguard_width}","via":"harvest"},"note":"Drawn as the handguard's, read with it."}]},"barrel_od":{"label":"The barrel's diameter","kind":"length","measurements":[{"id":"assumed","value":0.53,"unit":"in","source":{"type":"derived","expr":"{panzer-ar57-ult-16-upper.barrel_od}","basis":"An assumption for the drawing, not a reading: this barrel is inside the handguard from end to end in every view (its brake's jam nut stands against the lip); drawn at the 16 in's diameter, read on its photo ahead of its handguard.","via":"harvest"}}]},"barrel_rear_x":{"label":"The barrel's breech end ahead of the takedown pin (hidden in the receiver)","kind":"length","measurements":[{"id":"assumed","value":5.508,"unit":"in","source":{"type":"derived","expr":"{panzer-ar57-ult-16-upper.barrel_rear_x}","basis":"An assumption for the drawing, not a reading: the breech is inside the receiver, the same monobloc as the 16 in's; drawn where the 16 in's sellers' figures put it. From there to the brake's rear face is 12.16 in on this photo as read, the listing's 12 and a little; the 16 in's breech moved 0.43 back with its brake when its photo was read through a camera (2026-10-18), and this photo isn't yet.","via":"harvest"}}]},"bore_d":{"label":"The bore","kind":"length","measurements":[{"id":"derived","value":0.224,"unit":"in","pm":0.003,"source":{"type":"derived","basis":"The cartridge's name: 5.7 mm across (5.7 / 25.4); the bore is drawn as one plain hole at it.","via":"harvest"}}]},"brake_bore_d":{"label":"The brake's bore","kind":"length","measurements":[{"id":"derived","value":0.204,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.brake_slot_width}","via":"harvest"},"note":"The slot across its front opens the bore it runs into: drawn as wide as the slot."}]},"feed_pocket_d":{"label":"The round pocket in the receiver's top the magazine's feed tower sits in: its diameter","kind":"length","measurements":[{"id":"derived","value":1.883,"unit":"in","pm":0.08,"source":{"type":"derived","expr":"{fn-p90-50-magazine.tower_d} + 2 * {.lug_clearance}","via":"harvest"},"note":"What the pocket holds, a clearance round it: the magazine's own figure. No view shows the pocket from above with a scale; the notch it makes in each wall is read (feed_notch_length)."}]},"handguard_id":{"label":"The handguard's bore (round the barrel)","kind":"length","measurements":[{"id":"assumed","value":0.82,"unit":"in","source":{"type":"derived","expr":"{panzer-ar57-ult-16-upper.handguard_id}","basis":"An assumption for the drawing, not a reading: the same assumption as the 16 in upper's; no view of this one gives it either.","via":"harvest"}}]},"channel_rear_x":{"label":"The charging handle's channel along the receiver's right side: its rear end","kind":"length","measurements":[{"id":"photo","value":0.774,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (on a 2.5x crop the channel's rear end at 300 px, at 300, 797 px) through the camera fitted to it (the header) on the side face (0.72 in out): 0.495 in batch 10's pin frame.","via":"harvest"}}]},"channel_front_x":{"label":"The channel's front end","kind":"length","measurements":[{"id":"photo","value":6.988,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (on a 2.5x crop its front end at 896 px, at 896, 801 px) through the camera fitted to it (the header) on the side face (0.72 in out): 6.905 in batch 10's pin frame.","via":"harvest"}}]},"channel_bottom_y":{"label":"The channel's lower edge above the pin line","kind":"length","measurements":[{"id":"photo","value":0.358,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (822 px, at 580, 823 px) through the camera fitted to it (the header) on the side face (0.72 in out): 0.43 in batch 10's pin frame.","via":"harvest"}}]},"channel_top_y":{"label":"The channel's upper edge above the pin line","kind":"length","measurements":[{"id":"photo","value":0.865,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (774 px, at 580, 775 px) through the camera fitted to it (the header) on the side face (0.72 in out): 0.95 in batch 10's pin frame.","via":"harvest"}}]},"handle_rear_x":{"label":"The charging handle's tab in the channel: its rear end","kind":"length","measurements":[{"id":"photo","value":5.296,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (the raised tab from 728 px, at 729, 797 px) through the camera fitted to it (the header) on the handle's tab (0.92 in out): 5.1 in batch 10's pin frame.","via":"harvest"}}]},"handle_front_x":{"label":"The handle's tab: its front end","kind":"length","measurements":[{"id":"photo","value":6.907,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (to 884 px, at 885, 798 px) through the camera fitted to it (the header) on the handle's tab (0.92 in out): 6.78 in batch 10's pin frame.","via":"harvest"}}]},"handle_bottom_y":{"label":"The handle's tab: its lower edge above the pin line","kind":"length","measurements":[{"id":"photo","value":0.433,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (814 px, at 803, 815 px) through the camera fitted to it (the header) on the handle's tab (0.92 in out): 0.53 in batch 10's pin frame.","via":"harvest"}}]},"handle_top_y":{"label":"The handle's tab: its upper edge above the pin line","kind":"length","measurements":[{"id":"photo","value":0.79,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (780 px, at 803, 781 px) through the camera fitted to it (the header) on the handle's tab (0.92 in out): 0.9 in batch 10's pin frame.","via":"harvest"}}]},"bolt_window_rear_x":{"label":"The opening in the channel's floor onto the bolt: its rear end","kind":"length","measurements":[{"id":"photo","value":3.141,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (the dark opening on a 2.5x crop from 530 px, at 530, 798 px) through the camera fitted to it (the header) on the channel's floor (0.62 in out): 2.97 in batch 10's pin frame.","via":"harvest"}}]},"bolt_window_front_x":{"label":"That opening's front end","kind":"length","measurements":[{"id":"photo","value":3.999,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-12-upper c261b4c5a32d (to 612 px, at 612, 799 px) through the camera fitted to it (the header) on the channel's floor (0.62 in out): 3.85 in batch 10's pin frame.","via":"harvest"}}]},"channel_depth":{"label":"How deep the channel is cut into the side","kind":"length","measurements":[{"id":"assumed","value":0.1,"unit":"in","source":{"type":"derived","expr":"{panzer-ar57-ult-16-upper.channel_depth}","basis":"An assumption for the drawing, not a reading: the same assumption as the 16 in upper's; no view of this one gives it either.","via":"harvest"}}]},"channel_gap":{"label":"The gap round the handle's bar in its channel","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","source":{"type":"derived","expr":"{panzer-ar57-ult-16-upper.channel_gap}","basis":"An assumption for the drawing, not a reading: the same assumption as the 16 in upper's; no view of this one gives it either.","via":"harvest"}}]},"handle_out":{"label":"How far the handle's tab stands out of the receiver's right side","kind":"length","measurements":[{"id":"assumed","value":0.2,"unit":"in","source":{"type":"derived","expr":"{panzer-ar57-ult-16-upper.handle_out}","basis":"An assumption for the drawing, not a reading: the same assumption as the 16 in upper's; no view of this one gives it either.","via":"harvest"}}]},"bolt_window_depth":{"label":"How deep the opening onto the bolt goes into the receiver from the channel's floor","kind":"length","measurements":[{"id":"assumed","value":0.3,"unit":"in","source":{"type":"derived","expr":"{panzer-ar57-ult-16-upper.bolt_window_depth}","basis":"An assumption for the drawing, not a reading: the same assumption as the 16 in upper's; no view of this one gives it either.","via":"harvest"}}]},"muzzle_shoulder_x":{"label":"The barrel's shoulder ahead of the takedown pin: where a muzzle device seats (its brake's rear face)","kind":"length","measurements":[{"id":"derived","value":17.444,"unit":"in","source":{"type":"derived","expr":"{.brake_rear_x}","via":"harvest"},"note":"The brake comes on it: the upper occupies the muzzle slot, and this is where its own brake stands."}]},"handguard_height":{"label":"The handguard's height, from its underside to the top the magazine lies on (the front block's rails apart)","kind":"length","measurements":[{"id":"derived","value":1.537,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.tray_top_y} - {.handguard_bottom_y}","via":"harvest"}}]}}},{"subject":"panzer-ar57-ult-16-upper","title":"Panzer Arms AR57 Ultra Light Tactical Complete AR-15 Upper Receiver - 5.7x28mm - 16\"","dimensions":{"weight":{"label":"Weight (as sold: its barrel, brake, handguard, bolt and handle; the magazine and buffer apart)","kind":"mass","measurements":[{"id":"center","value":3,"unit":"lb","pm":0.5,"stated":"Upper Weight ~3 lbs","source":{"type":"spec","publisher":"retailer","name":"AR Five Seven Center (ar-57center.com), home page: Cartridge 5.7×28mm NATO Capacity 50 Rounds Upper Weight ~3 lbs Full Build ~6 lbs Barrel Options 12″ / 16″","url":"https://www.ar-57center.com/","retrieved":"2026-10-18","via":"harvest"},"note":"One approximate figure for both barrel lengths; whether the magazine is in it isn't said."},{"id":"metal","value":51.7,"unit":"oz","pm":9,"source":{"type":"derived","basis":"The model's metal (2026-10-20: the lug's front, the handguard's underside and its lower rail read on the photo from above, 51.9 before; 2026-10-19: the riser and the keel read narrower, the rail block's face cut back to where it stands and the latch added, 53.3 before; detail pass, 2026-10-18: the handguard's chamfers and keel, the receiver's chamfer and the plate's notch cut; batch 10's 58.6 before them; the width read at 1.44, the 16 in's front read through its photo's camera and its front block on the magazine's seat through it, 2026-10-18, 56.1 before that): the receiver with its rail block, the handle and the catch (15.68 cubic inches) and the handguard (7.00) in 7075 at std.density.aluminium_7075 (1.632 oz a cubic inch), the barrel and brake (3.22) in steel at std.density.steel (4.565): 25.6 + 11.4 + 14.7 oz. Over, by what the receiver's inside is: it is drawn solid round its bolt (an 8620 bolt about 0.75 across, Small Arms Review's photo), and its opening down into the lower's well isn't drawn; the ± is that.","via":"harvest"}}],"adopt":{"from":"center","reason":"A published figure for the upper, if one for both lengths and approximate; the model's metal (drawn solid inside) is 0.2 lb over it and within the two figures' ±."},"note":"No page on file gives a weight for this upper alone. ar-57center.com (AR Five Seven Center, which names no owner and sells the 12 in and 16 in ULT uppers) gives one figure for the platform's upper."},"barrel_length":{"label":"Barrel length (the listing's own figure)","kind":"length","measurements":[{"id":"pa","value":16,"unit":"in","pm":0.5,"stated":"Barrel Length 16","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Panzer Arms AR57 Ultra Light Tactical Complete AR-15 Upper Receiver - 5.7x28mm - 16\" (ULT0116), Specifications","url":"https://www.primaryarms.com/panzer-arms-ar57-ultra-light-tactical-5-7x28mm-complete-upper-16in","retrieved":"2026-10-18","via":"harvest"}},{"id":"classic","value":16,"unit":"in","pm":0.5,"stated":"The barrel is 16 inches with a perforated muzzle brake attached on 1/2 x 28 threads making the overall length 18 inches","source":{"type":"spec","publisher":"retailer","name":"Classic Firearms, AR57 16\" Complete ULT M-LOK Upper Receiver 5.7x28 (ACC-AR57-ULT-57-UPPER, MPN AR57-ULT16), Product description","url":"https://www.classicfirearms.com/ar57-5-7x28-ult-upper-receiver/","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"pa","reason":"Both sellers give 16; Primary Arms' specifications table is the listing's own figure."}},"barrel_with_brake_length":{"label":"The barrel with its brake on (the sellers' \"overall length\" of the barrel)","kind":"length","measurements":[{"id":"classic","value":18,"unit":"in","pm":0.5,"stated":"The barrel is 16 inches with a perforated muzzle brake attached on 1/2 x 28 threads making the overall length 18 inches","source":{"type":"spec","publisher":"retailer","name":"Classic Firearms, AR57 16\" Complete ULT M-LOK Upper Receiver 5.7x28, Product description","url":"https://www.classicfirearms.com/ar57-5-7x28-ult-upper-receiver/","retrieved":"2026-10-18","via":"harvest"}},{"id":"classic-specs","value":18,"unit":"in","pm":0.5,"stated":"Barrel is 16\", threaded 1/2x28 With perforated brake attached overall barrel length 18\"","source":{"type":"spec","publisher":"retailer","name":"Classic Firearms, AR57 16\" Complete ULT M-LOK Upper Receiver 5.7x28, Specs","url":"https://www.classicfirearms.com/ar57-5-7x28-ult-upper-receiver/","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"classic","reason":"The description and the specs on one page say the same. The brake as drawn is 1.51 long ahead of its shoulder (brake_rear_x to muzzle_end_x): the 2 in over the barrel's 16 can't all be the brake's, and where the barrel's 16 is counted from isn't said."}},"overall_length":{"label":"The receiver's back to the muzzle end","kind":"length","measurements":[{"id":"classic","value":24.5625,"unit":"in","pm":0.03125,"stated":"The receiver and rail block measures just over 17 inches overall length; from the receiver back to the muzzle end, the total length is 24 9/16 inches.","source":{"type":"spec","publisher":"retailer","name":"Classic Firearms, AR57 16\" Complete ULT M-LOK Upper Receiver 5.7x28, Product description","url":"https://www.classicfirearms.com/ar57-5-7x28-ult-upper-receiver/","retrieved":"2026-10-18","via":"harvest"}},{"id":"classic-specs","value":24.5,"unit":"in","pm":0.05,"stated":"Complete overall length of receiver 24.5\"","source":{"type":"spec","publisher":"retailer","name":"Classic Firearms, AR57 16\" Complete ULT M-LOK Upper Receiver 5.7x28, Specs","url":"https://www.classicfirearms.com/ar57-5-7x28-ult-upper-receiver/","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"classic","reason":"The same page gives both; 24 9/16 is to the sixteenth and says what it runs between (the receiver's back to the muzzle end), 24.5 is the specs' rounding of it."}},"monobloc_length":{"label":"The receiver and its rails, one block with the handguard: its overall length as the seller gives it","kind":"length","measurements":[{"id":"classic","value":17,"unit":"in","pm":0.25,"stated":"The receiver and rail block measures just over 17 inches overall length; from the receiver back to the muzzle end, the total length is 24 9/16 inches.","source":{"type":"spec","publisher":"retailer","name":"Classic Firearms, AR57 16\" Complete ULT M-LOK Upper Receiver 5.7x28, Product description","url":"https://www.classicfirearms.com/ar57-5-7x28-ult-upper-receiver/","retrieved":"2026-10-18","via":"harvest"}}],"note":"What it spans isn't said. Through the photo's camera: the receiver's rear face to the handguard's front lip 17.74, to the front block's rail's front end 16.94; the rail's rear overhang to the lip 18.84. None of these is \"just over 17\" but the second with batch 10's correction to the published length (17.11). Kept as the seller's words; nothing is drawn from it."},"muzzle_end_x":{"label":"The brake's front end ahead of the takedown pin","kind":"length","measurements":[{"id":"derived","value":23.9415,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.overall_length} + {std.ar15.upper_rear_face_x}","via":"harvest"},"note":"The published back-to-muzzle length from the receiver's rear face, which is the standard's (it stops ahead of the lower's buffer tower; the photo's rear face reads 0.04 further back, its near edge 0.45 in nearer the lens). The rail block overhangs behind it."},{"id":"camera","value":23.508,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"Read on 054c636f9e79 through the camera fitted to its own features of known size (the header; .cache/ar57-camera/fit054.py, PP=free WH=0.72): the traced outline's x max (94.3 px, the brake's prongs; muzzle_end_x_pinframe) on the plane of the prongs' near side (0.28 in out of the centre plane, toward the lens). The fit's own one sigma there 0.034; refitted without each group of features in turn the front lands 23.49 to 23.60; a width 0.06 either side moves it 0.03. A radial distortion term fitted beside it (k1 -0.17 ± 0.04, the receiver rail's thirteen edges bowing by 0.3 px) puts the front at 23.81, but reads the brake 2.25 long where this camera without it and the 12 in's (no distortion, 0.013 ± 0.015) read the same brake 2.13: the term isn't borne out at the photo's edge, where the brake is. The ± is the spread of the readings beside it.","via":"harvest"}},{"id":"twelve","value":23.36,"unit":"in","pm":0.12,"source":{"type":"derived","basis":"The 12 in upper's brake front through its own photo's camera (panzer-ar57-ult-12-upper.muzzle_end_x, 19.58: that camera's features reach to the front block, 3.3 in short of its brake, and its lens has no distortion) and the 4 in the two barrels differ by (16 and 12, their listings), less the 12 in's jam nut (its photo: 0.22 thick between the handguard's lip and the brake), which sets its brake that much further out on a thread of the same length. Without the nut's 0.22: 23.58. The two uppers' receivers and handguards are one part: the two cameras agree on the upper M-LOK row's foremost slot within 0.01 and on the magazine's room within 0.012.","via":"harvest"}},{"id":"center","value":23.68,"unit":"in","pm":0.15,"source":{"type":"derived","basis":"Read on ar-57center.com's right view of the 16 in (references/panzer-ar57-ult-16-upper 9d225b7d85c8, 800 x 600: another photographer) through a camera fitted to its lug holes' near rims, its receiver rail's thirteen slots' near edges and its upper M-LOK row's five whole slots (.cache/ar57-camera/fitsmall.py): its brake's prongs at 797.5 px. At 31 px/in the fit can't fix the lens's distance: held at each distance from 26 to 125 in the front reads 23.86 to 23.54, the M-LOK row's foremost slot 16.27 to 16.28; at 40 to 60 in, which the light seen through its holes gives (3.2 and 2.3 px narrower than the holes), 23.73 to 23.64. Its pins alone, read as a flat frame, give 23.93: that photo's muzzle stands nearer its lens (the rail reads 30.9 px/in, the M-LOK row 31.7).","via":"harvest"}},{"id":"patent","value":23.73,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"US 2011/0168009 A1 (Robb and Royce, the first-generation AR-57's application; the user's copy, references/panzer-ar57-ult-16-upper/docs/d01f14553d4f.pdf), FIG. 5, drawn to scale by its own holes (each 0.25 in across against the pin spacing, 98.4 px/in at 150 dpi): the barrel's breech face 6.15 in ahead of the takedown pin, 0.22 behind the pivot; FIG. 6B has it 2.16 ahead of the magazine's rear end. This upper's 16 in barrel from there is 22.15 to its crown; its brake (2.13 long, the two cameras) is threaded on with the crown 0.5 to 0.6 inside it (a 1/2-28 muzzle thread's usual length, assumed): 23.68 to 23.78. The ULT is the second generation: where its breech is isn't drawn.","via":"user"}}],"adopt":{"from":"camera","reason":"The photo the model is drawn from, read through a camera on its own features of known size; the other photos and the first generation's drawing put the brake's front at 23.36 to 23.73, and none at the seller's 24 9/16 from the receiver's back (derived: 23.94), which stays beside them: what it is counted from isn't said, and the same page's \"just over 17 inches\" for the receiver and rail block (monobloc_length) doesn't fit one reading of either."}},"muzzle_end_x_pinframe":{"label":"The brake's front end as Primary Arms' left view reads it in its pin frame (the outline's map's other end: muzzle_end_x)","kind":"length","measurements":[{"id":"photo","value":23.325,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79 (Primary Arms ULT0116_02.jpg, the left side straight on, 2200 x 1467)","scaleRef":"the lug holes' centres (takedown 1965.2, 826.8; pivot 1453.9, 826.4 px) as std.ar15.pin_spacing: 80.21 px/in","method":"the traced outline's x max (profiles.side): the brake's prongs at 96 px","via":"harvest"}}]},"rail_slots":{"label":"How many slots the receiver's top rail has","kind":"count","measurements":[{"id":"photo","value":13,"unit":"count","source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper fe9d442f7b56 (Classic Firearms acc-ar57-001-slc16_1, the receiver's left rear close) and 054c636f9e79","scaleRef":"none: a count","method":"14 teeth along the rail on a 3x crop of fe9d442f7b56, the gaps between them the slots; 13 gaps between the 14 tooth runs along row 630 of 054c636f9e79; 14 teeth from above in 0bde48a31171","via":"harvest"}},{"id":"classic","value":13,"unit":"count","stated":"The sight system is a 13 slot Picatinny over the operating handle, with 3-slot upper and lower forward rails.","source":{"type":"spec","publisher":"retailer","name":"Classic Firearms, AR57 16\" Complete ULT M-LOK Upper Receiver 5.7x28, Product description","url":"https://www.classicfirearms.com/ar57-5-7x28-ult-upper-receiver/","retrieved":"2026-10-18","via":"harvest"}},{"id":"pa","value":13,"unit":"count","stated":"13-slot Picatinny rail over the operating handle, plus 3-slot upper and lower forward rails","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, AR57 Ultra Light Tactical (ULT0116), Features","url":"https://www.primaryarms.com/panzer-arms-ar57-ultra-light-tactical-5-7x28mm-complete-upper-16in","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"photo","reason":"Counted; the two sellers say the same."}},"front_rail_slots":{"label":"How many slots each forward rail (on the front block's top, and under it) has","kind":"count","measurements":[{"id":"photo","value":3,"unit":"count","source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79 and b894132847e8","scaleRef":"none: a count","method":"four teeth with three gaps on the front block's top (row 630 of 054c636f9e79, 662 to 789 px) and on its underside; three slots on the top rail from ahead in b894132847e8","via":"harvest"}},{"id":"classic","value":3,"unit":"count","stated":"with 3-slot upper and lower forward rails","source":{"type":"spec","publisher":"retailer","name":"Classic Firearms, AR57 16\" Complete ULT M-LOK Upper Receiver 5.7x28, Product description","url":"https://www.classicfirearms.com/ar57-5-7x28-ult-upper-receiver/","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"photo","reason":"Counted; the seller says the same."}},"rail_top_above_pin":{"label":"The rear rail's top above the pin line","kind":"length","measurements":[{"id":"photo","value":2.545,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"the tooth tops of the traced outline over x -1.5 to 3.4 (623 px, the same row as the front rail's tooth tops 15 in ahead: the photo is level); the rail's near edge, 0.42 in nearer the lens than the pins, reads at most 0.01 high from the lens's distance the yaw implies","via":"harvest"}}]},"front_rail_top_above_pin":{"label":"The front block's rail top above the pin line","kind":"length","measurements":[{"id":"photo","value":2.54,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"the tooth tops of the traced outline over x 15.0 to 16.2 (623 px)","via":"harvest"}}]},"rail_slot0_x":{"label":"The rear rail's rearmost slot's centre ahead of the takedown pin (negative: behind it)","kind":"length","measurements":[{"id":"photo","value":-1.163,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"the gap between the rearmost two teeth along row 630, 2056 to 2061 px, its centre 2058.5 px. The thirteen gaps' centres run 2058.5 to 1685 px: 31.1 px apart, 0.388 in, 1.5% short of the standard's 0.394 (the rail drawn has the standard's pitch from this slot)","via":"harvest"},"note":"A gap's middle, where the backdrop shows through the slot: the line of sight crosses the rail at an angle growing away from the lens, so the gap seen is cut down from one side, 16.8 px wide at the rail's front and 5.8 at its rear, and its middle moves by half of that."},{"id":"camera","value":-1.248,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"Read on 054c636f9e79 through the camera fitted to it (the header): the thirteen slots' front edges on the rail's near face (the left edges of the gaps along rows 626 to 632, 1676.5 to 2056.0 px: 31.63 px apart, 0.3943 in in the pin frame, the standard's pitch) fitted with the rest of the camera, on MIL-STD-1913's pitch and slot width; one sigma 0.013.","via":"harvest"}}],"adopt":{"from":"camera","reason":"The slots' near edges, which the view across the rail doesn't move; the gaps' middles read the rail 1.5% short and its first slot 0.085 in forward."}},"front_rail_slot0_x":{"label":"The front block's top rail: its rearmost slot's centre ahead of the takedown pin","kind":"length","measurements":[{"id":"photo","value":15.282,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on 054c636f9e79 through the camera fitted to it (the header): the front rail's teeth along rows 626 to 628, each tooth's near face from its front edge (where the backdrop ends: 691.2, 722.1, 753.1 px) to its rear edge (where its lit rear face begins: 674.9, 705.6, 736.5 px), and the rear faces' far ends (685.4, 715.7, 745.9 px), on MIL-STD-1913's pitch and slot width; one sigma 0.016. Batch 10 read the gap's middle at 747 px (15.188 in the pin frame) and its yaw correction made it 15.394; through the camera that middle is 15.252, the gap seen being cut down from one side by the view across the rail.","via":"harvest"}}]},"lower_rail_slot0_x":{"label":"The front block's lower rail: its rearmost slot's centre ahead of the takedown pin","kind":"length","measurements":[{"id":"photo","value":15.51,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"Read on 054c636f9e79 (the gap between the lower rail's two rearmost teeth, 718 to 733 px, centre 726 px: 15.45 in the pin frame) through the camera fitted to it (the header), on the rail's near face: 15.48; and moved forward by what the same reading does on the front block's top rail (its gap's middle through the camera, 15.252, against its teeth's near edges, 15.282).","via":"harvest"}}]},"lower_rail_bottom_y":{"label":"The lower forward rail's face (its tooth tops, facing down) above the pin line (negative: below)","kind":"length","measurements":[{"id":"photo","value":-0.11,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"the traced outline's lowest run over x 15.3 to 16.3 (835 px)","via":"harvest"}},{"id":"camera","value":-0.093,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-16-upper 054c636f9e79 through the camera fitted to it (the header; 2026-10-20): the teeth's faces along row 834.6 (columns 640 to 745, x 15.6 to 16.4) on the near edge of the rail's flat (0.328 out): -0.093 to -0.094; the slots' floors along row 824.6 read 0.031, 0.124 above them (MIL-STD-1913's .118 +.008).","via":"harvest"}}],"adopt":{"from":"camera","reason":"Through the photo's camera at the edge the silhouette is, the slots' depth the standard's. The 12 in's photo reads it -0.150 as the near edge and -0.080 as the far one."}},"receiver_rear_x":{"label":"The receiver's rear face behind the takedown pin (negative)","kind":"length","measurements":[{"id":"std","value":-0.621,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.ar15.upper_rear_face_x}","via":"harvest"},"note":"The standard's: an upper that fits a mil-spec lower stops ahead of its buffer tower."},{"id":"photo","value":-0.663,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"the traced outline's rear face over y 0.6 to 1.5 (2018 to 2020 px)","via":"harvest"},"note":"The face's near edge, 0.45 in nearer the lens than the pins: from the 60 in the yaw and the M-LOK pitch imply, 0.04 behind where the face is."}],"adopt":{"from":"std","reason":"The standard's place is where a receiver that fits the lower must stop; the photo's 0.04 in more is the size perspective gives its near edge."}},"rail_rear_x":{"label":"The rail block's rear end (the rail overhangs the receiver)","kind":"length","measurements":[{"id":"photo","value":-1.723,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"the traced outline's x min (2103 px)","via":"harvest"}}]},"rail_rear_x_pinframe":{"label":"The rail block's rear end as the trace's frame reads it (the outline's map behind the takedown pin: rail_rear_x)","kind":"length","measurements":[{"id":"derived","value":-1.723,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{.rail_rear_x}","via":"harvest"},"note":"The same reading: through the photo's camera the rail's rear end is -1.725 (2103 px on the rail's near face), and the outline behind the takedown pin is taken as read."}]},"rail_front_x":{"label":"The rear rail's front end (its front tooth's face) ahead of the takedown pin","kind":"length","measurements":[{"id":"photo","value":3.978,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"the front tooth's run along row 626, 1646 to 1676 px: its front face 1646 px","via":"harvest"}}]},"rail_block_front_x":{"label":"The rear rail block's front face, flush with its rail's front end (the magazine's latch stands out of it)","kind":"length","measurements":[{"id":"photo","value":4.04,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"the block's front face on a 3x crop, 1640 to 1641 px, under the rail's front tooth","via":"harvest"}},{"id":"camera","value":3.97,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-16-upper 054c636f9e79 through the camera fitted to it (the header; 2026-10-19 (night), .cache/ar57-camera/pass3/): above the magazine's top round the face shows as a light band between its corners, 1640.6 to 1645.6 px along rows 646 to 652, white ahead of it to the magazine's end: its far corner (riser_width / 2 out, beyond the centre plane) 3.971, its near corner 3.966. The lens 43 in off and nearly square, the depth moves it 0.01 at most.","via":"harvest"}}],"adopt":{"from":"camera","reason":"The face where it stands, through the photo's camera; the 12 in's photo, through its own, has 3.98."},"note":"2026-10-19 (night): the magazine's round end doesn't bear on this face. Through each upper's own camera the face stands 0.10 in behind the magazine's rearmost point (this upper's photo: 3.97 against 4.070; the 12 in's: 3.98 against 4.082), white between the two above and below the latch (latch_bottom_y, latch_top_y), which stands out of the face into the notch in the magazine's round end (fn-p90-50-magazine's own side photo, 76c0d7572a37, has the notch). The face is flush with the rail's front end (rail_front_x, 3.978). The pin frame's reading (photo) is the face's far corner: kept as read."},"receiver_top_y":{"label":"The receiver's top either side of the rail block (the step it rises from)","kind":"length","measurements":[{"id":"photo","value":1.59,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"the traced outline's top behind the rail's overhang (x -0.9 to -0.7: 1.59): the receiver's top at its rear, under the rail block's ramp","via":"harvest"}}]},"tray_top_y":{"label":"The handguard's top (the magazine lies on it) above the pin line","kind":"length","measurements":[{"id":"photo","value":1.566,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"the magazine's underside, 701 px, with no light between it and the handguard from 877 px back (columns 880 to 1420 dark from the magazine's top to the M-LOK slots); ahead of 877 px the handguard's top ramps down to 717 px (1.367) under the magazine's front end, where light shows between them, and the outline has that ramp","via":"harvest"}},{"id":"seat","value":1.6,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{.mag_underside_y}","via":"harvest"},"note":"The magazine lies on it, no light between them from 877 px back: one plane for both (a seat drawn bearing). The model clamps the traced outline's run under the magazine to it (the trace, cut at 699 px, gives 1.576 to 1.584)."}],"adopt":{"from":"seat","reason":"The seat is the magazine's underside, read where light shows under it; the outline's top there is the cut the trace was made with, 0.02 under it."}},"tray_front_y":{"label":"The handguard's top at its lowest, where it ramps down ahead of the magazine's underside to the front block","kind":"length","measurements":[{"id":"photo","value":1.367,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"the light under the magazine's front end on a 3x crop: its lower edge at 717 px from 780 px back to where it closes at 877 px","via":"harvest"},"note":"The handguard's inside is drawn under this, a wall below it: the dip isn't an opening (no light is seen into the handguard there)."}]},"tray_dip_rear_x":{"label":"Where the handguard's top begins its ramp down to the front block, ahead of the takedown pin","kind":"length","measurements":[{"id":"photo","value":13.6,"unit":"in","pm":0.06,"source":{"type":"derived","basis":"Read on a 3x crop of 054c636f9e79 where the light under the magazine's front end closes, 877 px (13.567 in the pin frame), through the camera fitted to it (the header) at the upper chamfer's top (0.42 in out).","via":"harvest"}}]},"underside_y":{"label":"The receiver's underside above the pin line (it sits on the lower's deck)","kind":"length","measurements":[{"id":"std","value":0.2485,"unit":"in","pm":0.0015,"source":{"type":"derived","expr":"{std.ar15.deck_y}","via":"harvest"}},{"id":"photo","value":0.25,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"the traced outline's lower edge over x 1.0 to 6.0 (806 px)","via":"harvest"}}],"adopt":{"from":"std","reason":"The seat is the lower's deck; the photo agrees within 0.002 in."}},"takedown_lug_front_x":{"label":"The takedown lug's front face ahead of the takedown pin (the lug under the receiver, at the lower's rear slot)","kind":"length","measurements":[{"id":"camera","value":0.22,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-16-upper 054c636f9e79 through the camera fitted to it (the header; 2026-10-20): the lug's front face, turned toward the lens (over x 7.9), shows as a light band 7 px wide, 1940.7 to 1947.8 px along rows 808 to 838: its far edge (the silhouette, the lug's half width beyond the centre plane) reads 0.220 to 0.223 and its near edge 0.219 to 0.222. Its rear face (the near edge, 1983.4 px) reads -0.220 to -0.223: the lug 0.44 long, centred on its pin. The traced outline, the silhouette read as a near edge, has its front at 0.308. The 12 in's photo through its own camera reads its front face's two edges 0.216 to 0.226.","via":"harvest"}}],"adopt":{"from":"camera","reason":"Both edges of the face agree, and the other upper's photo through its own camera reads the same; the model's lug is cut to it, the outline's front being the face's far edge read as its near one."}},"handguard_bottom_y":{"label":"The handguard's underside above the pin line","kind":"length","measurements":[{"id":"photo","value":0.088,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"the traced outline's lower edge over x 7.5 to 14 (819 px)","via":"harvest"}},{"id":"camera","value":0.098,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-16-upper 054c636f9e79 through the camera fitted to it (the header; 2026-10-20, .cache/ar57-camera/pass4/): the outline's lower edge at 818.8 to 819.8 px along columns 1000 to 1250 (x 8.9 to 12.1), on the keel's near side (keel_width / 2): the lens, 0.57 above the pin line, sees the underside's near edge, which is the silhouette there: 0.093 to 0.103.","via":"harvest"}}],"adopt":{"from":"camera","reason":"Through the photo's camera at the edge the silhouette is. The 12 in's photo, from a lens 2.6 in under the pin line, reads the same underside 0.058 as its near edge and 0.135 as its far edge, which is the silhouette from below: this one between them. An underside seen from below shows its far edge, a face turned toward the lens its far edge, and a lens above a part sees an underside's near edge (2026-10-20: the 12 in's close photo, 2.6 in under the pin line, read both ways brackets this one's)."}},"handguard_front_x":{"label":"The handguard's front end (the front block's lip round the barrel) ahead of the takedown pin","kind":"length","measurements":[{"id":"photo","value":17.12,"unit":"in","pm":0.07,"source":{"type":"derived","basis":"Read on 054c636f9e79 where the outline's lip meets the barrel (17.05 in the pin frame, 597 px: handguard_front_x_pinframe) through the camera fitted to it (the header), at the keel's depth (0.42 in out): 17.12, where the outline's map puts its clipped end (17.134); at the side face's depth (0.72 out) the same pixel is 17.05. The ± spans the two.","via":"harvest"}}]},"handguard_front_x_pinframe":{"label":"The handguard's front end as Primary Arms' left view reads it in its pin frame (where the traced outline is clipped: the barrel and brake are the model's)","kind":"length","measurements":[{"id":"photo","value":17.05,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"where the outline's lip meets the barrel's run (597 px)","via":"harvest"}}]},"front_block_rear_x":{"label":"The front block's rear face (the magazine's front cap stands against it), ahead of the takedown pin","kind":"length","measurements":[{"id":"photo","value":15,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"Read on 054c636f9e79 (a 3x crop: the block's rearmost tooth runs back to 767 px, where the magazine's front cap covers it: 14.938 in the pin frame) through the camera fitted to it (the header), on the rail's near face: 14.998.","via":"harvest"}}]},"front_block_face_x":{"label":"The front block's rear face at the magazine's body's height, where the cap's body stands against it (ahead of the takedown pin); the rail's rear tooth reaches further back over the magazine's top (front_block_rear_x)","kind":"length","measurements":[{"id":"photo","value":14.939,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"Read on 054c636f9e79 along rows 640, 655, 670 and 685 px (each the median of three): a dark line at 763 px between the block's grey (72 to 76) and the cap's (85 to 106), 14.988 in the pin frame, through the camera fitted to it (the header) on the cap's near side (half fn-p90-50-magazine.cap_width out): the lens's foot is behind the block (x 7.9), so the cap's near side, standing out past the riser, covers it, and the line is the cap's front edge where it stands against the block. At the riser's side the same pixel is 15.04 (this session's first reading); batch 12 had 15.19 through the yaw correction to the published length.","via":"harvest"}},{"id":"outline","value":15.01,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"The traced outline's block face (profiles.side: 14.947 to 14.954 in the pin frame from 1.38 to 2.54 above the pins, the trace's threshold edge about 766 px) through the outline's map (the header): 15.010 (the camera at the riser's side: 15.002).","via":"harvest"}},{"id":"seat","value":14.939,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{.mag_rear_x} + {fn-p90-50-magazine.length}","via":"harvest"},"note":"Where the magazine's cap stands, its rear end on the latch: the face drawn bearing on it (a seat is drawn bearing)."}],"adopt":{"from":"seat","reason":"The magazine (fn-p90-50-magazine.length, its two ends through both uppers' cameras) stands with its cap against this face and its round end on the latch: the face is drawn where its cap stands, on the cap's front edge read through this photo's camera (photo). The traced outline's face (outline, 15.01 through its map) stands 0.07 ahead of it: the block is filled out to the seat below the magazine's top."},"note":"Detail pass, 2026-10-18 (the magazine's owner read the 12 in's at 1669 px): the cap's lugs stand at its two sides with a gap between them as wide as the rail (fn-p90-50-magazine.cap_lug_width), and the block's rearmost tooth runs back between them over the magazine's top. Drawn so: the block cut back to this face below the magazine's top."},"bore_axis_above_pin":{"label":"Bore axis above the takedown pin centre","kind":"length","measurements":[{"id":"photo","value":0.957,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"the middle of the barrel's dark run in columns 270 to 560 px (728 to 770 px: 749 px), ahead of the handguard; the photo level (the pins within 0.4 px, the two rails' tops on one row)","via":"harvest"},"note":"0.08 in above a mil-spec upper's (std.ar15.bore_axis_y, 0.8775): this upper's bore isn't the standard's; its buffer, in the lower's tube, is on the tube's axis."}]},"barrel_od":{"label":"The barrel's diameter ahead of the handguard","kind":"length","measurements":[{"id":"photo","value":0.53,"unit":"in","pm":0.025,"source":{"type":"derived","basis":"Read on 054c636f9e79: the barrel's dark run in columns 270 to 560 px is 42 px (0.524 in the pin frame); the camera fitted to the photo (the header) has 79.7 px/in across the barrel there (batch 10: 76.2, its yaw correction's slope at x 20, and 0.55). A glossy black tube reads up to 3% thin on white: in the ±.","via":"harvest"}}]},"brake_rear_x":{"label":"The brake's rear face (the barrel's shoulder it seats on) ahead of the takedown pin","kind":"length","measurements":[{"id":"photo","value":21.38,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"Read on 054c636f9e79 (a 2x crop: the brake's rear band begins at 262 px, 21.234 in the pin frame) through the camera fitted to it (the header), on the brake's near side (0.3 in out): 21.375. The brake is then 2.13 long to its front end (muzzle_end_x).","via":"harvest"}}]},"brake_band_front_x":{"label":"The brake's rear band (a plain collar behind its ports): its front end, where a groove parts it from the ported body","kind":"length","measurements":[{"id":"photo","value":21.88,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"Read on 054c636f9e79 (a 2x crop: the groove at 222 px, 21.733 in the pin frame) through the camera fitted to it (the header), on the brake's near side: 21.881.","via":"harvest"}}]},"brake_port_x":{"label":"The brake's rearmost column of ports: its centre ahead of the takedown pin","kind":"length","measurements":[{"id":"photo","value":22.32,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"Read on 054c636f9e79 (along row 742 the three ports are dark from 181-195, 162-175 and 142-155 px: centres 188, 168.5, 148.5 px; 22.157 in the pin frame) through the camera fitted to it (the header), on the brake's near side: 22.316, 22.563, 22.816.","via":"harvest"}}]},"brake_port_pitch":{"label":"The ports' columns, centre to centre","kind":"length","measurements":[{"id":"photo","value":0.25,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"Read on 054c636f9e79: the three centres through the camera fitted to it (the header), 22.316, 22.563, 22.816: 0.250 apart (19.75 px at its 78.9 px/in there; batch 10 had 75.5 by its yaw correction, and 0.262).","via":"harvest"}}]},"brake_port_d":{"label":"A port's diameter","kind":"length","measurements":[{"id":"photo","value":0.171,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"Read on 054c636f9e79: the ports at the side of the brake are 13 to 14 px across along x (rows 742 to 766), at the camera's 78.9 px/in there (the header; batch 10: 75.5 and 0.179).","via":"harvest"}}]},"brake_port_columns":{"label":"How many columns of ports along the brake","kind":"count","measurements":[{"id":"photo","value":3,"unit":"count","source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"three ports along each row of 054c636f9e79 and of b894132847e8","via":"harvest"}}]},"brake_ports_around":{"label":"How many ports round the brake in each column","kind":"count","measurements":[{"id":"photo","value":6,"unit":"count","source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"three rows show on the half facing the lens, their centres at 741.5 and 764.5 px and a sliver at 728 to 730 px about the brake's axis at 748.5 px (radius 23.5 px): 17 degrees above the side, 43 below and 77 above, 60 degrees apart: six round, one every 60 degrees. The count of the far half is inferred from the spacing","via":"harvest"}}]},"brake_port_phase":{"label":"Where the ports are clocked: the row nearest the left side's middle, in degrees above it","kind":"count","measurements":[{"id":"photo","value":17,"unit":"count","source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"as brake_ports_around: asin(7 / 23.5). A threaded brake stops where its thread times it; the photo's is drawn","via":"harvest"},"note":"Degrees, held as a count."}]},"brake_slot_depth":{"label":"The slot across the brake's front end: how deep it runs back from the front","kind":"length","measurements":[{"id":"photo","value":0.43,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"Read on 054c636f9e79: light through the front end between 740 and 758 px from 96 to 130 px (columns 97 to 125 have two dark runs, 135 one): 34 px at the camera's 78.9 px/in along the brake there (the header; batch 10: 75.5 and 0.45).","via":"harvest"}}]},"brake_slot_width":{"label":"The slot's height (it runs across, side to side)","kind":"length","measurements":[{"id":"photo","value":0.226,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on 054c636f9e79: 18 px (740 to 758 px) at the camera's 79.7 px/in across the brake there (the header; batch 10: 75.5 and 0.24).","via":"harvest"}}]},"brake_od":{"label":"The brake's diameter","kind":"length","measurements":[{"id":"photo","value":0.59,"unit":"in","pm":0.025,"source":{"type":"derived","basis":"Read on 054c636f9e79: 47 px (725 to 772 px) in columns 210 to 250, at the camera's 79.7 px/in across the brake there (the header; batch 10: 75.5, its yaw correction's slope at x 22.5, and 0.62).","via":"harvest"}}]},"mlok_upper_slots":{"label":"M-LOK slots in the upper row on each side","kind":"count","measurements":[{"id":"photo","value":6,"unit":"count","source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79 (the left side); 9d225b7d85c8 (the right side, ar-57center.com)","scaleRef":"none: a count","method":"six slots in the upper row on the left, the foremost under the front block; six on the right in the smaller photo","via":"harvest"}}]},"mlok_lower_slots":{"label":"M-LOK slots in the lower row on each side (staggered between the upper row's)","kind":"count","measurements":[{"id":"photo","value":5,"unit":"count","source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"none: a count","method":"five see-through slots along row 790 (gaps at 689-772, 810-898, 931-1023, 1055-1150, 1178-1277 px), each midway between two of the upper row's","via":"harvest"}}]},"mlok_upper_front_x":{"label":"The upper row's foremost slot's centre ahead of the takedown pin","kind":"length","measurements":[{"id":"photo","value":16.32,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on 054c636f9e79 through the camera fitted to it (the header): the five whole slots behind the foremost (their dark runs' middles along rows 738 to 740 and 753 to 755: 781.9, 907.4, 1033.7, 1160.9, 1288.6 px) on Magpul's 40 mm pitch and the side face's plane (handguard_width), fitted with the camera: the foremost's centre 16.321, one sigma 0.011. The foremost slot itself (608 to 708 px, partly hidden, its middle 658 px) reads 16.287 through the camera; batch 10's yaw correction made it 16.544.","via":"harvest"}}]},"mlok_lower_front_x":{"label":"The lower row's foremost slot's centre ahead of the takedown pin","kind":"length","measurements":[{"id":"photo","value":15.5,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"Read on 054c636f9e79 through the camera fitted to it (the header): the five see-through slots' middles along row 790 (730.5, 854, 977, 1102.5, 1227.5 px) are where the near and the far chamfers' slots overlap, the far one 16.5 to 2.8 px off the near one toward the lens's foot; with half that taken off, the near slots' centres are 15.499, 13.935, 12.379, 10.794, 9.217 (1.571 apart on average, Magpul's 1.575), the foremost 0.03 behind midway between the upper row's two foremost (16.321 - 0.7875). Batch 10 corrected the middles alone for its yaw: 15.607, the pitch 1.1% long.","via":"harvest"}}]},"mlok_upper_y":{"label":"The upper row's centre line above the pin line","kind":"length","measurements":[{"id":"photo","value":1.005,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"the upper row's slots between rows 735 and 757 px on a 3x crop: centre 746 px","via":"harvest"}}]},"mlok_lower_y":{"label":"The lower row's centre line above the pin line, as it shows from the side","kind":"length","measurements":[{"id":"photo","value":0.506,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"the see-through slots between rows 780 and 792 px: centre 786 px","via":"harvest"}}]},"mag_rear_x":{"label":"The seated magazine's rear end ahead of the takedown pin (where the upper holds it)","kind":"length","measurements":[{"id":"photo","value":4.1,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79 (the magazine in)","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"the magazine's feed housing's rear face on a 3x crop, 1635 px, against the rail block's front face","via":"harvest"}},{"id":"camera","value":4.065,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on 054c636f9e79 through the camera fitted to it (the header): the round rear end's outline at 1636 px (row 668) as the half circle in plan it is, as wide as the magazine (fn-p90-50-magazine.width), the line of sight tangent to it 0.25 in nearer the lens than its rearmost point. The rail block's face at 1640.5 px reads 4.043 through the same camera (its far corner, 3.971: rail_block_front_x).","via":"harvest"}},{"id":"above-latch","value":4.07,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-16-upper 054c636f9e79 through the camera fitted to it (the header; 2026-10-19 (night), .cache/ar57-camera/pass3/magend.py): the round end's outline against the white above the latch, 1635.3 to 1635.4 px along rows 646 to 654, as the half circle in plan it is (fn-p90-50-magazine.width), the line of sight tangent to it near its rearmost point: 4.070 to 4.071.","via":"harvest"}}],"adopt":{"from":"above-latch","reason":"The round end read as the round end it is, through the photo's camera, against the white above the latch; row 668 (camera) is at the latch's height, the latch's dark lobe beside it; the pin frame's 4.10 is the outline's pixel as if the end were flat across at the pins' depth. The 12 in's photo, through its own camera, has 4.082 for the same seat."}},"latch_bottom_y":{"label":"The magazine's latch, out of the rear rail block's front face into the notch in the magazine's round end: its underside above the pin line","kind":"length","measurements":[{"id":"camera","value":1.78,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-16-upper 054c636f9e79 through the camera fitted to it (the header; 2026-10-19 (night)): the dark lobe between the magazine's round end and the block's face, white above it to row 657.5 and below it from row 684.5 (between 1636 and 1640 px): its foot at 1.782 on the centre plane. The 12 in's photo has it from 1.76 to 2.10.","via":"harvest"}}]},"latch_top_y":{"label":"The magazine's latch: its top above the pin line","kind":"length","measurements":[{"id":"camera","value":2.12,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"Read on references/panzer-ar57-ult-16-upper 054c636f9e79 as latch_bottom_y: its top at row 657.5, 2.123.","via":"harvest"}}]},"latch_width":{"label":"The magazine's latch: across","kind":"length","measurements":[{"id":"assumed","value":0.62,"unit":"in","pm":0.1,"source":{"type":"derived","expr":"{.riser_width}","basis":"An assumption for the drawing, not a reading: no view shows it across. In the 12 in's photo its near side stands at the face's near corner (a dark strip, 627 to 632 px, beside the lit face): drawn as wide as the face it stands out of.","via":"harvest"}}]},"mag_underside_y":{"label":"The seated magazine's underside (its body's flat bottom, lying on the handguard's top) above the pin line","kind":"length","measurements":[{"id":"photo","value":1.572,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79 (the magazine in)","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"the magazine's lower edge where light shows under it at its front (700 to 701 px, x 780 to 877 px) and along its body on a 3x crop of its rear (700 px); its feed boss hangs below it into the receiver's pocket to 742 px (1.055)","via":"harvest"}},{"id":"columns","value":1.6,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"luminance down columns 830, 845 and 860 px (each the median of five), where light shows under the magazine's front end: its lit lower edge (71 to 82) gives way to the light (169 to 189) at 698.5 px; down columns 1040 to 1300 px, where it lies on the handguard, the chamfer's dark band begins under it at 699 px: 1.594 to 1.600 (detail pass, 2026-10-18; the magazine's owner read the same row)","via":"harvest"}}],"adopt":{"from":"columns","reason":"Read down columns where light shows under it, the edge sharp; batch 10's 700 to 701 px is two pixels under it, inside the dark band the chamfer makes under the magazine."}},"feed_pocket_x":{"label":"The receiver's round pocket the magazine's feed boss sits in: its centre ahead of the takedown pin","kind":"length","measurements":[{"id":"photo","value":5.09,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79 (the magazine in)","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"the boss's ends where it shows through the notch in the near wall, 1496 and 1618 px on a 3x crop: the middle","via":"harvest"}},{"id":"tower","value":5.045,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.mag_rear_x} + {fn-p90-50-magazine.width} / 2","via":"harvest"},"note":"Where the magazine's tower stands: concentric with its round end (US 4,905,394's FIG. 3 and FIG. 4; the magazine's own side photo has the tower flush with its rear end within a pixel), the round end against the rail block. No view on file shows the pocket from above."}],"adopt":{"from":"tower","reason":"The pocket holds the magazine's tower, so it is drawn round it. The notch the tower shows through in the near wall reads 5.09 in the pin frame and 5.111 through the photo's camera (photo): a chord whose two ends lie at two depths of a wall seen from a lens off to one side, ahead of the tower's place by 0.05 to 0.07; both are kept, and the magazine's own photo (the tower concentric with the round end) decides it."}},"feed_notch_length":{"label":"The notch in each wall the magazine's feed tower shows through: its length","kind":"length","measurements":[{"id":"photo","value":1.52,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79 (the magazine in)","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"the round piece's ends where it shows through the near wall, 1496 and 1618 px on a 3x crop, the wall dark either side of it","via":"harvest"},"note":"The notch's, not the tower's: the walls cover the tower's ends (the magazine's ledger reads it 1.88 across on photos of it alone)."}]},"feed_pocket_d":{"label":"The round pocket in the receiver's top the magazine's feed tower sits in: its diameter","kind":"length","measurements":[{"id":"derived","value":1.883,"unit":"in","pm":0.08,"source":{"type":"derived","expr":"{fn-p90-50-magazine.tower_d} + 2 * {.lug_clearance}","via":"harvest"},"note":"What the pocket holds, a clearance round it: the magazine's own figure (each part its own half of the seat: the tower is the magazine's, the pocket this upper's). No view shows the pocket from above with a scale; the notch it makes in each wall is read (feed_notch_length)."}]},"feed_pocket_floor_y":{"label":"The pocket's floor (the boss's underside) above the pin line","kind":"length","measurements":[{"id":"photo","value":1.055,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79 (the magazine in)","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"the boss's lower edge on a 3x crop, 742 px","via":"harvest"}}]},"handguard_width":{"label":"The handguard's width across its side faces (the receiver's too: one figure)","kind":"length","measurements":[{"id":"assumed","value":1.5,"unit":"in","pm":0.15,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file is square to the part's end. The feed boss (1.52 across, feed_pocket_d) shows through a notch in the near wall, so the wall stands about as far out as the boss's edge; the three-quarter views (0bde48a31171, b894132847e8) have the side faces standing well outside the rails' standard 0.835 and about as wide as the magazine.","via":"harvest"}},{"id":"camera","value":1.44,"unit":"in","pm":0.06,"source":{"type":"derived","basis":"Read through cameras fitted to two three-quarter views (2026-10-18, .cache/ar57-camera/): the side face is the plane the M-LOK slots' rims lie on, its distance from the centre plane what the fit leaves free, the rails standing on the centre plane. The 12 in's from ahead, right and above (46e53e61437f, the same section): the front block's 3-slot rail (its slots' edges and its head's flat and bevel, MIL-STD-1913), the side face's three upper M-LOK slots (their rims' outlines on Magpul's 40 mm pitch, their size left free) and the side face's lower edge (the bottom of the outline, where the lower chamfer is seen edge on), with the heights the 16 in's straight view reads: 1.42 (1.44 with the brake as well, its own size free); the slots alone 1.34. The 16 in's from behind, left and above (0bde48a31171): its receiver rail (its teeth's edges, MIL-STD-1913), the left plate's three screws on the receiver's side (plate_screw_*, read near the pins) and four M-LOK slots: 1.42 to 1.47 as the rail's slots are registered, 1.33 to 1.42 on the rims' outlines. One sigma of each fit 0.02 to 0.03; the ± is what the feature sets and the slot outlines move it. The check on a figure no fit took: the slots' size, left free, comes out 33.4 x 6.9 mm and 31.7 x 7.4 mm (Magpul: 32 x 7, approximate); with the pitch left free instead, 39.9 to 40.2 mm. The slots' outlines are their rims: whatever isn't the face's grey (an outline of only the dark and the backdrop follows what shows through a slot, the slots under it and across, and read the 12 in's 0.03 to 0.08 wider: the user, watching the fit). b894132847e8 fixes no width: one row of slots and a barrel of a free radius.","via":"harvest"}}],"adopt":{"from":"camera","reason":"A reading over an assumption: two views of the two uppers through cameras on standard features. The assumption's 1.5 is inside its own ± and at the edge of the reading's; it stays beside it."}},"width":{"label":"The receiver's width","kind":"length","measurements":[{"id":"derived","value":1.44,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{.handguard_width}","via":"harvest"},"note":"Drawn as the handguard's: the side face runs on from the handguard across the receiver in Primary Arms' left view, the handguard's rear edge a curve on it; the plate's screws on the receiver's side and the slots on the handguard's lie on one plane in 0bde48a31171's fit."}]},"handguard_rear_x":{"label":"The handguard's rear edge on the receiver's side (the seam), at its middle","kind":"length","measurements":[{"id":"photo","value":6.88,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"on a 3x crop the handguard's rear edge is a curve on the side face from 6.51 at the tray's height (1443 px, row 710) to 7.26 at its foot (1383 px, row 800): its middle, 1413 px","via":"harvest"}}]},"handguard_rear_top_x":{"label":"The seam at the tray's height","kind":"length","measurements":[{"id":"photo","value":6.51,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"the curve's upper end on a 3x crop, 1443 px at row 710","via":"harvest"}}]},"handguard_rear_bottom_x":{"label":"The seam at the side face's foot","kind":"length","measurements":[{"id":"photo","value":7.26,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"the curve's lower end on a 3x crop, 1383 px at row 800","via":"harvest"}}]},"side_face_bottom_y":{"label":"The height the seam's lower end was read at (handguard_rear_bottom_x), low on the handguard's side","kind":"length","measurements":[{"id":"photo","value":0.33,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"the line along the handguard's lower part on a 3x crop (800 px), from the seam to the front block","via":"harvest"}}],"note":"Batch 10 read this as the side face's foot, a line along the handguard's lower part; the detail pass (2026-10-18) read the section's lines down columns of the photo (lower_chamfer_top_y, keel_top_y): the side face ends higher, at 0.665, and the line this was read on is the lower chamfer's foot, 6 px lower (keel_top_y). Kept for what it was read with: the seam's curve ends here (the model's seam runs from handguard_rear_top_x at the tray to handguard_rear_bottom_x at this height)."},"side_face_top_y":{"label":"The handguard's side face's upper edge, where the chamfer up to its top begins (above the pin line)","kind":"length","measurements":[{"id":"photo","value":1.3,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"luminance down columns 1040, 1170, 1290 and 1300 px (each the median of five; .cache/ar57d/prof.py in the batch-12 worktree): under the magazine's underside (699 px) a dark band, the chamfer facing up into the magazine's black underside, to 722.5 to 723 px, where the side face's grey (67) begins: 1.294 to 1.300","via":"harvest"},"note":"From the side the chamfer shows its height; how far it runs across is the riser's width's (riser_width): the top flat is drawn as wide as the riser standing on it at the front block."}],"note":"The handguard's section is a top flat, a chamfer down each side to a flat side face, a chamfer under that, and a keel: seen square from ahead in neither photo, but its lines are read down columns of this one, and the views from ahead (b894132847e8; the 12 in's 46e53e61437f, its front ring) show the faces: the front block's riser runs straight down into the upper chamfer, the lower block's sides with their holes into the lower one, and the lower row of M-LOK slots on the lower chamfer (foreshortened from above where the upper row isn't)."},"receiver_chamfer_top_y":{"label":"The receiver's chamfer along its upper sides, under the rail block: its upper edge, where the receiver's side rises set in to the riser's foot (above the pin line)","kind":"length","measurements":[{"id":"photo","value":1.525,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"luminance down columns 1800, 1880 and 1940 px (x 2.06, 1.06, 0.31): the face's grey (52 to 56) above, the band's darker grey (38 to 48) from 704.5 to 705 px down to 723.5 px, where the side face's (52 to 60) begins again: its top 1.519 to 1.525, its foot 1.288 (side_face_top_y's line on the handguard reads 1.294 to 1.300: one line, the receiver's band and the handguard's chamfer meeting the side face on it)","via":"harvest"}}],"note":"Detail pass, 2026-10-18: a band along the receiver's upper side from its rear face to a ramp under the rail block's window (receiver_chamfer_front_*), dark in the straight view as the handguard's chamfer is, lit from above in 0bde48a31171 and fe9d442f7b56 (a face turned up). Drawn as the handguard's chamfer's plane carried back to this height, the side above it set in to the deck at the riser's foot."},"receiver_chamfer_front_top_x":{"label":"That chamfer's front end, where it meets the face ahead of it, at receiver_chamfer_front_top_y (ahead of the takedown pin)","kind":"length","measurements":[{"id":"photo","value":3.7,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"along row 707 px: the face's grey (61 to 66) ends at 1668.5 px, the band's dark (13 to 28) begins","via":"harvest"}}]},"receiver_chamfer_front_top_y":{"label":"The height receiver_chamfer_front_top_x is read at","kind":"length","measurements":[{"id":"photo","value":1.494,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"row 707 px","via":"harvest"}}]},"receiver_chamfer_front_low_x":{"label":"That chamfer's front end lower down, at receiver_chamfer_front_low_y (ahead of the takedown pin): the end is a ramp","kind":"length","measurements":[{"id":"photo","value":3.5,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"along row 721 px: the face's grey (51 to 60) ends at 1684.5 px; rows 712 and 717 between (1673.5, 1679.5 px) on the same line: the band's front end leans back going down, a ramp","via":"harvest"}}]},"receiver_chamfer_front_low_y":{"label":"The height receiver_chamfer_front_low_x is read at","kind":"length","measurements":[{"id":"photo","value":1.319,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"row 721 px","via":"harvest"}}]},"lower_chamfer_top_y":{"label":"The handguard's side face's lower edge, where the chamfer under it begins (above the pin line)","kind":"length","measurements":[{"id":"photo","value":0.665,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"luminance down columns 1040, 1170 and 1290 px: a step from 61-68 to 68-76 at 773 to 773.5 px, the side face above, the lower chamfer (another tone) below it, with the lower row of M-LOK slots in it (see-through at 780 to 792 px)","via":"harvest"}}]},"keel_top_y":{"label":"The lower chamfer's foot, where a short flat side (the keel, the lower block's width) runs down to the underside (above the pin line)","kind":"length","measurements":[{"id":"photo","value":0.259,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"luminance down columns 1040, 1170, 1290 and 1300 px: a dark line (50 to 54) at 805 to 807 px, the keel's face (62 to 70) under it to the underside at 819 px","via":"harvest"},"note":"The line batch 10 read at 800 px (side_face_bottom_y)."}]},"lower_chamfer_run":{"label":"How far the lower chamfer runs in, across, from the side face to the keel","kind":"length","measurements":[{"id":"derived","value":0.385,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{.handguard_width} / 2 - {.keel_width} / 2","via":"harvest"},"note":"The keel's width read (keel_width), 2026-10-19 (night); it had been taken to be the riser's."}]},"lower_chamfer_drop":{"label":"How far the lower chamfer drops, from the side face's foot to the keel","kind":"length","measurements":[{"id":"derived","value":0.406,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.lower_chamfer_top_y} - {.keel_top_y}","via":"harvest"}}]},"lower_face_angle":{"label":"The lower chamfers' faces: where their normal points, about +x from the top (90 is the right side)","kind":"angle","measurements":[{"id":"derived","value":133.48,"unit":"deg","pm":4,"source":{"type":"derived","basis":"90 degrees + atan(lower_chamfer_run / lower_chamfer_drop) = 90 + atan(0.385 / 0.406): the chamfer's normal, from the read heights, the read width and the read keel; the ± is the run's.","via":"harvest"}}],"note":"The expressions have no arctangent: the value is written as worked out, 90 + atan(lower_chamfer_run / lower_chamfer_drop), and the part's test holds it to its inputs."},"mlok_lower_z":{"label":"The lower row's slots' centres on the lower chamfer: how far out of the centre plane","kind":"length","measurements":[{"id":"derived","value":0.5692,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.handguard_width} / 2 - ({.lower_chamfer_top_y} - {.mlok_lower_y}) * {.lower_chamfer_run} / {.lower_chamfer_drop}","via":"harvest"}}]},"mlok_lower_axis_y":{"label":"The lower row's anchor: on the centre plane where the line square to the lower chamfer through a slot's centre meets it (above the pin line)","kind":"length","measurements":[{"id":"derived","value":1.0458,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{.mlok_lower_y} + {.mlok_lower_z} * {.lower_chamfer_run} / {.lower_chamfer_drop}","via":"harvest"}}]},"mlok_lower_face_distance":{"label":"The lower chamfer's surface from the lower row's anchor, along its normal","kind":"length","measurements":[{"id":"derived","value":0.7845,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{.mlok_lower_z} * sqrt(1 + ({.lower_chamfer_run} / {.lower_chamfer_drop}) * ({.lower_chamfer_run} / {.lower_chamfer_drop}))","via":"harvest"}}]},"riser_width":{"label":"The riser under each rail block's rail head (the face the rows of blind holes are in), across","kind":"length","measurements":[{"id":"assumed","value":0.835,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing: the riser's flat sides run down from the rail's head in fe9d442f7b56 and 0bde48a31171 with no step, so it is drawn as wide as the head's top (std.picatinny.top_width).","via":"harvest"}},{"id":"twelve","value":0.62,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{panzer-ar57-ult-12-upper.riser_width}","basis":"The 12 in upper's reading (its ledger says what it rests on: three rows of blind holes through cameras fitted to two views of it from ahead): the same receiver and blocks. This upper's photo bears it out: the rail block's front face shows 0.62 across between its corners (rail_block_front_x).","via":"harvest"}}],"adopt":{"from":"twelve","reason":"A reading over an assumption: the views from behind have the head's overhang against the dark riser, where it doesn't show."}},"keel_width":{"label":"The keel under the lower chamfers (the lower block's side, the face its row of blind holes is in), across","kind":"length","measurements":[{"id":"twelve","value":0.67,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{panzer-ar57-ult-12-upper.keel_width}","basis":"The 12 in upper's reading (its ledger says what it rests on: the lower block's row of blind holes through a camera fitted to a view of it from ahead): the same handguard section.","via":"harvest"}}]},"top_flat_width":{"label":"The handguard's top flat under the magazine (between the two upper chamfers), across","kind":"length","measurements":[{"id":"assumed","value":0.835,"unit":"in","pm":0.1,"source":{"type":"derived","expr":"{panzer-ar57-ult-12-upper.top_flat_width}","basis":"An assumption for the drawing, not a reading: the 12 in upper's (its ledger says why): the flat is under the magazine in every view on file.","via":"harvest"}}]},"handguard_id":{"label":"The handguard's bore (round the barrel)","kind":"length","measurements":[{"id":"assumed","value":0.82,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing: from ahead (b894132847e8) the barrel stands in a round opening with a margin about half its own radius; drawn so, and closed above by the tray.","via":"harvest"}}]},"barrel_rear_x":{"label":"The barrel's breech end ahead of the takedown pin (hidden in the receiver)","kind":"length","measurements":[{"id":"derived","value":5.508,"unit":"in","pm":0.5,"source":{"type":"derived","expr":"{.muzzle_end_x} - {.barrel_with_brake_length}","via":"harvest"},"note":"The sellers' barrel with its brake on (18) back from the brake's front: where the drawn barrel starts. How the 18 is counted isn't said: hence the ±."}]},"cross_hole_y":{"label":"The row of cross holes along the rear rail block's side, under its slots: their centres above the pin line","kind":"length","measurements":[{"id":"photo","value":2.26,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"on a 5x crop (window.png) the holes' centres at 645 px","via":"harvest"}}]},"cross_hole_d":{"label":"Those holes' diameter","kind":"length","measurements":[{"id":"photo","value":0.125,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"on a 5x crop the holes are 10 px across","via":"harvest"},"note":"One under each slot (their centres 31.75 px apart on the crop, between the teeth): drawn under each of the 13."}]},"front_hole_y":{"label":"The row of five holes along the front block's top, under its rail: their centres above the pin line","kind":"length","measurements":[{"id":"photo","value":2.22,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"on a 3x crop (front_side.png) the five holes at 648 px","via":"harvest"}}]},"front_hole_x":{"label":"The front block's five holes: the rearmost's centre ahead of the takedown pin","kind":"length","measurements":[{"id":"photo","value":15.19,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"Read on a 3x crop of 054c636f9e79 (the five holes at 753, 732, 710, 690 and 668 px: the rearmost 15.113 in the pin frame) through the camera fitted to it (the header), on the face they are in (0.31 in out: the 12 in's oblique 46e53e61437f has the holes on a face set in under the rail's head, .cache/ar57-camera/fitW2.py): 15.188, the foremost 16.262.","via":"harvest"}}]},"front_hole_pitch":{"label":"The front block's holes, centre to centre","kind":"length","measurements":[{"id":"photo","value":0.269,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"Read on the same crop through the camera: the rearmost and the foremost 1.074 apart, four pitches (batch 10: 77 px/in by its yaw correction, and 0.276).","via":"harvest"}}]},"lower_hole_y":{"label":"The row of five holes along the lower rail's block: their centres above the pin line","kind":"length","measurements":[{"id":"photo","value":0.186,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"on a 3x crop (front_side.png) the five holes at 811.7 px","via":"harvest"}}]},"lower_hole_x":{"label":"The lower block's five holes: the rearmost's centre ahead of the takedown pin","kind":"length","measurements":[{"id":"photo","value":15.33,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"Read on a 3x crop of 054c636f9e79 (the five holes at 738, 713, 688, 663 and 640 px: the rearmost 15.30 in the pin frame) through the camera fitted to it (the header), on the keel's side (0.42 in out): 15.329, the foremost 16.560.","via":"harvest"}}]},"lower_hole_pitch":{"label":"The lower block's holes, centre to centre","kind":"length","measurements":[{"id":"photo","value":0.308,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"Read on the same crop through the camera: the rearmost and the foremost 1.231 apart, four pitches (batch 10: 77.2 px/in, and 0.317).","via":"harvest"}}]},"bolt_end_d":{"label":"The bolt's round rear end, as it shows in the receiver's rear face","kind":"length","measurements":[{"id":"assumed","value":0.75,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing: from behind and to the left (0bde48a31171) the bolt's end, marked UP, is a disc a little more than half the receiver's rear face across; Small Arms Review's photo of the bolt (1d3f4024e9c6) has it a plain round bar. No view is square to it.","via":"harvest"}}]},"bolt_end_proud":{"label":"How far the bolt's end stands out of the rear face","kind":"length","measurements":[{"id":"assumed","value":0.05,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing: it stands a little proud in 0bde48a31171; no view gives it in profile.","via":"harvest"}}]},"catch_rear_x":{"label":"The magazine catch's lever in the rail block's window: its rear face","kind":"length","measurements":[{"id":"photo","value":2.93,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"the lever's outline in the window on a 5x crop (window.png), 1730 px","via":"harvest"}}]},"catch_front_x":{"label":"The lever's front face","kind":"length","measurements":[{"id":"photo","value":3.16,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"the same crop, 1712 px","via":"harvest"}}]},"catch_bottom_y":{"label":"The lever's lower end above the pin line","kind":"length","measurements":[{"id":"photo","value":1.77,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"the same crop, 685 px","via":"harvest"}}]},"catch_top_y":{"label":"The lever's upper end above the pin line","kind":"length","measurements":[{"id":"photo","value":2.14,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"the same crop, 655 px","via":"harvest"}}]},"catch_out":{"label":"How far the lever stands out of the rail block's right side","kind":"length","measurements":[{"id":"assumed","value":0.3,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: from ahead and to the right (b894132847e8) the lever stands out of the window on the right about a third of the rail's width; no view gives it square.","via":"harvest"}}]},"cross_hole_depth":{"label":"How deep the blind holes along the rail block and the front block go","kind":"length","measurements":[{"id":"assumed","value":0.1,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing: they are dark, not lit through, in every view (the window beside them is); no view gives their depth.","via":"harvest"}}]},"front_rail_front_x":{"label":"The front block's top rail: its front end (its foremost tooth's face)","kind":"length","measurements":[{"id":"photo","value":16.32,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"Read on 054c636f9e79 (the foremost tooth's face along row 630, 662 px: 16.247 in the pin frame) through the camera fitted to it (the header), on the rail's near face: 16.324.","via":"harvest"}}]},"bore_d":{"label":"The bore","kind":"length","measurements":[{"id":"derived","value":0.224,"unit":"in","pm":0.003,"source":{"type":"derived","basis":"The cartridge's name: 5.7 mm across (5.7 / 25.4); the bore is drawn as one plain hole at it.","via":"harvest"}}]},"brake_bore_d":{"label":"The brake's bore","kind":"length","measurements":[{"id":"derived","value":0.24,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"The slot across its front (brake_slot_width) opens the bore it runs into: drawn as wide as the slot. Not read on its face.","via":"harvest"}}]},"brake_groove_w":{"label":"The groove between the brake's rear band and its ported body: its width","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing: a dark line 2 to 3 px wide on a 2x crop of 054c636f9e79, its depth not shown.","via":"harvest"}}]},"brake_groove_depth":{"label":"That groove's depth","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view gives it in profile.","via":"harvest"}}]},"channel_rear_x":{"label":"The charging handle's channel along the receiver's right side: its rear end","kind":"length","measurements":[{"id":"photo","value":0.57,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 9d225b7d85c8 (ar-57center.com upper-16-3.jpg, the 16 in's right side, 800 x 600)","scaleRef":"its lug holes (takedown 54.2, 339.9; pivot 251.8, 337.7 px) as std.ar15.pin_spacing: 31.0 px/in, the photo turned 0.64 degrees","method":"on a 5x crop the channel's rear end at 72 px","via":"harvest"}}]},"channel_front_x":{"label":"The channel's front end","kind":"length","measurements":[{"id":"photo","value":6.83,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 9d225b7d85c8 (ar-57center.com upper-16-3.jpg, the 16 in's right side, 800 x 600)","scaleRef":"its lug holes (takedown 54.2, 339.9; pivot 251.8, 337.7 px) as std.ar15.pin_spacing: 31.0 px/in, the photo turned 0.64 degrees","method":"on a 5x crop its front end at 266 px","via":"harvest"}}]},"channel_bottom_y":{"label":"The channel's lower edge above the pin line","kind":"length","measurements":[{"id":"photo","value":0.46,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 9d225b7d85c8 (ar-57center.com upper-16-3.jpg, the 16 in's right side, 800 x 600)","scaleRef":"its lug holes (takedown 54.2, 339.9; pivot 251.8, 337.7 px) as std.ar15.pin_spacing: 31.0 px/in, the photo turned 0.64 degrees","method":"on a 5x crop 327 px","via":"harvest"}}]},"channel_top_y":{"label":"The channel's upper edge above the pin line","kind":"length","measurements":[{"id":"photo","value":1,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 9d225b7d85c8 (ar-57center.com upper-16-3.jpg, the 16 in's right side, 800 x 600)","scaleRef":"its lug holes (takedown 54.2, 339.9; pivot 251.8, 337.7 px) as std.ar15.pin_spacing: 31.0 px/in, the photo turned 0.64 degrees","method":"on a 5x crop 310 px","via":"harvest"}}]},"handle_rear_x":{"label":"The charging handle's tab in the channel: its rear end","kind":"length","measurements":[{"id":"photo","value":5,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 9d225b7d85c8 (ar-57center.com upper-16-3.jpg, the 16 in's right side, 800 x 600)","scaleRef":"its lug holes (takedown 54.2, 339.9; pivot 251.8, 337.7 px) as std.ar15.pin_spacing: 31.0 px/in, the photo turned 0.64 degrees","method":"on a 5x crop the raised tab from 209 px","via":"harvest"}}]},"handle_front_x":{"label":"The handle's tab: its front end","kind":"length","measurements":[{"id":"photo","value":6.74,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 9d225b7d85c8 (ar-57center.com upper-16-3.jpg, the 16 in's right side, 800 x 600)","scaleRef":"its lug holes (takedown 54.2, 339.9; pivot 251.8, 337.7 px) as std.ar15.pin_spacing: 31.0 px/in, the photo turned 0.64 degrees","method":"to 263 px","via":"harvest"}}]},"handle_bottom_y":{"label":"The handle's tab: its lower edge above the pin line","kind":"length","measurements":[{"id":"photo","value":0.67,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 9d225b7d85c8 (ar-57center.com upper-16-3.jpg, the 16 in's right side, 800 x 600)","scaleRef":"its lug holes (takedown 54.2, 339.9; pivot 251.8, 337.7 px) as std.ar15.pin_spacing: 31.0 px/in, the photo turned 0.64 degrees","method":"321 px","via":"harvest"}}]},"handle_top_y":{"label":"The handle's tab: its upper edge above the pin line","kind":"length","measurements":[{"id":"photo","value":0.99,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 9d225b7d85c8 (ar-57center.com upper-16-3.jpg, the 16 in's right side, 800 x 600)","scaleRef":"its lug holes (takedown 54.2, 339.9; pivot 251.8, 337.7 px) as std.ar15.pin_spacing: 31.0 px/in, the photo turned 0.64 degrees","method":"311 px","via":"harvest"}}]},"bolt_window_rear_x":{"label":"The opening in the channel's floor onto the bolt: its rear end","kind":"length","measurements":[{"id":"photo","value":3.03,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 9d225b7d85c8 (ar-57center.com upper-16-3.jpg, the 16 in's right side, 800 x 600)","scaleRef":"its lug holes (takedown 54.2, 339.9; pivot 251.8, 337.7 px) as std.ar15.pin_spacing: 31.0 px/in, the photo turned 0.64 degrees","method":"the dark opening on a 5x crop from 148 px","via":"harvest"}}]},"bolt_window_front_x":{"label":"That opening's front end","kind":"length","measurements":[{"id":"photo","value":3.8,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 9d225b7d85c8 (ar-57center.com upper-16-3.jpg, the 16 in's right side, 800 x 600)","scaleRef":"its lug holes (takedown 54.2, 339.9; pivot 251.8, 337.7 px) as std.ar15.pin_spacing: 31.0 px/in, the photo turned 0.64 degrees","method":"to 172 px","via":"harvest"}}]},"plate_screw_y":{"label":"The three screws of the plate over the left side's channel: their centres above the pin line","kind":"length","measurements":[{"id":"photo","value":0.64,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"on a 1.5x crop the three heads at 775 px","via":"harvest"}}]},"plate_screw_rear_x":{"label":"The plate's rearmost screw","kind":"length","measurements":[{"id":"photo","value":0.94,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"1890 px","via":"harvest"}}]},"plate_screw_mid_x":{"label":"The plate's middle screw","kind":"length","measurements":[{"id":"photo","value":2.78,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"1743 px","via":"harvest"}}]},"plate_screw_front_x":{"label":"The plate's front screw","kind":"length","measurements":[{"id":"photo","value":6.43,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"1450 px","via":"harvest"}}]},"plate_notch_rear_x":{"label":"The round-topped notch in the left side's plate, over the channel: its rear edge (ahead of the takedown pin)","kind":"length","measurements":[{"id":"photo","value":2.97,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"its edge's dark line along rows 775, 785 and 795 px at 1723, 1726.5 and 1727 px","via":"harvest"}}],"note":"Detail pass, 2026-10-18: a notch with a round top in the plate's lower edge (054c636f9e79, fe9d442f7b56), lit inside as the face is, with a line across it at the channel's lower edge (0.446 in at column 1707 px; channel_bottom_y reads 0.46 on the right side): the plate cut away to the channel's floor there, over the right side's opening onto the bolt (bolt_window_rear_x)."},"plate_notch_front_x":{"label":"That notch's front edge","kind":"length","measurements":[{"id":"photo","value":3.47,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"its edge's dark line along rows 775, 785 and 795 px at 1689.5, 1686 and 1687 px","via":"harvest"}}]},"plate_notch_top_y":{"label":"That notch's round top, at its middle (above the pin line)","kind":"length","measurements":[{"id":"photo","value":0.777,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"down column 1707 px its edge's dark line at 764.5 px; at 1695 and 1718 px 768 px, a round as wide as the notch","via":"harvest"}}]},"plate_screw_d":{"label":"Those screws' heads, across","kind":"length","measurements":[{"id":"photo","value":0.21,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"17 px on the crop","via":"harvest"}}]},"channel_depth":{"label":"How deep the channel is cut into the side","kind":"length","measurements":[{"id":"assumed","value":0.1,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the channel's walls show as a thin dark line in both side views; no view gives its depth.","via":"harvest"}}]},"channel_gap":{"label":"The gap round the handle's bar in its channel, and round the left side's plate","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: a dark line about two pixels wide in 054c636f9e79 and c261b4c5a32d.","via":"harvest"}}]},"handle_out":{"label":"How far the handle's tab stands out of the receiver's right side","kind":"length","measurements":[{"id":"assumed","value":0.2,"unit":"in","pm":0.08,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: from ahead and to the right (b894132847e8) the tab stands out of the side about a third of the rail's width; no view is square to it.","via":"harvest"}}]},"bolt_window_depth":{"label":"How deep the opening onto the bolt goes into the receiver from the channel's floor","kind":"length","measurements":[{"id":"assumed","value":0.3,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: it is dark in every view; it opens onto the bolt, which isn't drawn.","via":"harvest"}}]},"handguard_wall":{"label":"The handguard's wall","kind":"length","measurements":[{"id":"assumed","value":0.12,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the M-LOK slots' see-through edges in 054c636f9e79 and the open front end in b894132847e8 show a thin wall, whose thickness no view on file gives in profile.","via":"harvest"}}]},"lug_clearance":{"label":"Each lug's clearance to the lower's slot it stands in, per side","kind":"length","measurements":[{"id":"assumed","value":0.005,"unit":"in","pm":0.005,"source":{"type":"derived","basis":"An assumption for the drawing: the lugs are drawn a few thousandths narrower than the lower's slots (std.ar15.rear_lug_slot_width, front_lug_slot_width) so the two models don't share space; no view gives the lugs' width.","via":"harvest"}}]},"window_rear_x":{"label":"The rear rail block's window for the handle (the larger, foremost of two): its rear end","kind":"length","measurements":[{"id":"photo","value":2.922,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"the window's rear edge on a 5x crop, 1731 px; the lever stands in its rear half","via":"harvest"}}]},"window_front_x":{"label":"The handle's window: its front end","kind":"length","measurements":[{"id":"photo","value":3.546,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"the window's front edge on a 5x crop, 1681 px","via":"harvest"}}]},"window2_rear_x":{"label":"The second, smaller window behind it: its rear end","kind":"length","measurements":[{"id":"photo","value":2.298,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"its rear edge on a 5x crop, 1781 px","via":"harvest"}}]},"window2_front_x":{"label":"The second window: its front end","kind":"length","measurements":[{"id":"photo","value":2.585,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"its front edge on a 5x crop, 1758 px","via":"harvest"}}]},"window_bottom_y":{"label":"The two windows' bottom edge above the pin line","kind":"length","measurements":[{"id":"photo","value":1.741,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"the windows' lower edge on a 5x crop, 687 px: the riser's foot on the receiver's top","via":"harvest"}}]},"window_top_y":{"label":"The two windows' top edge above the pin line","kind":"length","measurements":[{"id":"photo","value":2.127,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/panzer-ar57-ult-16-upper 054c636f9e79","scaleRef":"the lug holes as std.ar15.pin_spacing (80.21 px/in)","method":"the windows' upper edge on a 5x crop, 656 px, under the rail's cross holes","via":"harvest"}}]},"muzzle_shoulder_x":{"label":"The barrel's shoulder ahead of the takedown pin: where a muzzle device seats (its brake's rear face)","kind":"length","measurements":[{"id":"derived","value":21.38,"unit":"in","source":{"type":"derived","expr":"{.brake_rear_x}","via":"harvest"},"note":"The brake comes on it: the upper occupies the muzzle slot, and this is where its own brake stands."}]},"handguard_height":{"label":"The handguard's height, from its underside to the top the magazine lies on (the front block's rails apart)","kind":"length","measurements":[{"id":"derived","value":1.502,"unit":"in","source":{"type":"derived","expr":"{.tray_top_y} - {.handguard_bottom_y}","via":"harvest"}}]}}},{"subject":"precision-armament-m4-72","title":"Precision Armament M4-72 Severe-Duty® Compensator, 5.56 (M472-556)","dimensions":{"overall_length":{"label":"Overall length (rear face to front face)","kind":"length","measurements":[{"id":"pa","value":2.25,"unit":"in","pm":0.0005,"stated":"Length: 2.250\" (the Specs table's 5.56/.223 column)","source":{"type":"spec","publisher":"manufacturer","name":"Precision Armament, M4-72 Severe-Duty® Compensator (the product's page: its Specs table and description)","url":"https://precisionarmament.com/m4-72-severe-duty-compensator/","retrieved":"2026-10-28","via":"harvest"}},{"id":"sheet","value":2.25,"unit":"in","pm":0.0005,"stated":"Length 2.250” (the PRODUCT SPECIFICATIONS table's M472-556 column)","source":{"type":"spec","publisher":"manufacturer","name":"Precision Armament, M4-72 SEVERE-DUTY® COMPENSATOR product specifications (spec sheet, Rev 09-14-2026)","url":"https://precisionarmament.com/content/documents/INDIVIDUAL_SPEC_SHEETS/specs-m4-72-severe-duty-compensator.pdf","retrieved":"2026-10-28","via":"harvest"}},{"id":"mgw","value":2.25,"unit":"in","pm":0.0005,"stated":"2.250\" Length","source":{"type":"spec","publisher":"retailer","name":"Midwest Gun Works, Precision Armament M4-72 Severe-Duty 5.56MM / .223 Compensator 1/2x28\", Black (Code A04002), Features","url":"https://www.midwestgunworks.com/page/mgwi/prod/a04002","retrieved":"2026-10-28","via":"harvest"}}],"adopt":{"from":"pa","reason":"The maker's own page; its spec sheet and a seller say the same."}},"length":{"label":"Length ahead of the barrel's shoulder, installed (to the front face)","kind":"length","measurements":[{"id":"device","value":2.25,"unit":"in","pm":0.0005,"source":{"type":"derived","expr":"{.overall_length}","via":"harvest"}}],"note":"It seats on its own rear face. The maker recommends its Accu-Washer to time it (A02119, \"not included\"), a separate product: drawn without it, so the length is the device's own. With a washer on the shoulder the rifle is that washer's thickness longer."},"od":{"label":"Largest outside diameter (the body, the ring and the front cap)","kind":"length","measurements":[{"id":"pa","value":0.865,"unit":"in","pm":0.0005,"stated":"Diameter: 0.865\" (the Specs table's 5.56/.223 column)","source":{"type":"spec","publisher":"manufacturer","name":"Precision Armament, M4-72 Severe-Duty® Compensator (the product's page: its Specs table and description)","url":"https://precisionarmament.com/m4-72-severe-duty-compensator/","retrieved":"2026-10-28","via":"harvest"}},{"id":"sheet","value":0.865,"unit":"in","pm":0.0005,"stated":"Diameter 0.865” (the M472-556 column)","source":{"type":"spec","publisher":"manufacturer","name":"Precision Armament, M4-72 SEVERE-DUTY® COMPENSATOR product specifications (spec sheet, Rev 09-14-2026)","url":"https://precisionarmament.com/content/documents/INDIVIDUAL_SPEC_SHEETS/specs-m4-72-severe-duty-compensator.pdf","retrieved":"2026-10-28","via":"harvest"}},{"id":"mgw","value":0.865,"unit":"in","pm":0.0005,"stated":"0.865\" Diameter","source":{"type":"spec","publisher":"retailer","name":"Midwest Gun Works, Precision Armament M4-72 Severe-Duty 5.56MM / .223 Compensator 1/2x28\", Black (Code A04002), Features","url":"https://www.midwestgunworks.com/page/mgwi/prod/a04002","retrieved":"2026-10-28","via":"harvest"}}],"adopt":{"from":"pa","reason":"The maker's own page; its spec sheet and a seller say the same. In the photos the body, the ring and the front cap are one width within 2 px (339 to 342 px)."}},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"pa","value":2.6,"unit":"oz","pm":0.05,"stated":"Weight: 2.6oz (the Specs table's 5.56/.223 column; the description: \"an extremely lightweight (2.6 oz) and compact design\")","source":{"type":"spec","publisher":"manufacturer","name":"Precision Armament, M4-72 Severe-Duty® Compensator (the product's page: its Specs table and description)","url":"https://precisionarmament.com/m4-72-severe-duty-compensator/","retrieved":"2026-10-28","via":"harvest"}},{"id":"sheet","value":2.6,"unit":"oz","pm":0.05,"stated":"Weight 2.6 oz. (the M472-556 column)","source":{"type":"spec","publisher":"manufacturer","name":"Precision Armament, M4-72 SEVERE-DUTY® COMPENSATOR product specifications (spec sheet, Rev 09-14-2026)","url":"https://precisionarmament.com/content/documents/INDIVIDUAL_SPEC_SHEETS/specs-m4-72-severe-duty-compensator.pdf","retrieved":"2026-10-28","via":"harvest"}},{"id":"mgw","value":2.6,"unit":"oz","pm":0.05,"stated":"2.6oz Weight","source":{"type":"spec","publisher":"retailer","name":"Midwest Gun Works, Precision Armament M4-72 Severe-Duty 5.56MM / .223 Compensator 1/2x28\", Black (Code A04002), Features","url":"https://www.midwestgunworks.com/page/mgwi/prod/a04002","retrieved":"2026-10-28","via":"harvest"}}],"adopt":{"from":"pa","reason":"The maker's own page; its spec sheet and a seller say the same."}},"base_af":{"label":"Wrench flats at the rear, across flats","kind":"length","measurements":[{"id":"photo","value":0.766,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/precision-armament-m4-72 4edb633eb80e (Precision Armament's gallery, M4-72-SEVERE-DUTY-MUZZLE-BRAKE-SS-FRONT: the stainless one standing, muzzle up, the narrow flat and the logo's flat toward the lens, on white, 1024 x 1024)","scaleRef":"across, the body's own width, 341 px, as od (0.865): 394.2 px/in; along, its end faces 908 px apart as overall_length (2.250): 403.6 px/in","method":"the silhouette's width and its runs row by row below a level of 240 of 255 (.cache/batch15/precision-armament-m4-72/measure.py and ports.py); the end faces where their rims' arcs meet the sides","via":"harvest"},"note":"302 px from 0.04 to 0.26 from the rear face, where the silhouette is the flats at 3 and 9 o'clock (an octagon seen square on its top flat)."},{"id":"black","value":0.764,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/precision-armament-m4-72 a1a4c479327e (Precision Armament's gallery, M4-72-SEVERE-DUTY-MUZZLE-BRAKE-BLK-FRONT: the black one in the same pose, on white, 1024 x 1024)","scaleRef":"across, the body's 344 px as od (0.865): 397.7 px/in; along, its end faces 913.6 px apart as overall_length (2.250)","method":"as the stainless one's, below a level of 200","via":"harvest"},"note":"304 px."}],"adopt":{"from":"photo","reason":"The two photos agree within 0.002 in; the stainless one's edges are the sharper on white."},"note":"\"Tighten to 20-30 ft-lbs of torque using wrench flats at base of compensator\" (the installation guide)."},"base_flats":{"label":"Wrench flats, how many round the base","kind":"count","measurements":[{"id":"photo","value":8,"unit":"count","source":{"type":"photo","photo":"references/precision-armament-m4-72 4edb633eb80e (Precision Armament's gallery, M4-72-SEVERE-DUTY-MUZZLE-BRAKE-SS-FRONT: the stainless one standing, muzzle up, the narrow flat and the logo's flat toward the lens, on white, 1024 x 1024)","scaleRef":"across, the body's own width, 341 px, as od (0.865): 394.2 px/in; along, its end faces 908 px apart as overall_length (2.250): 403.6 px/in","method":"the silhouette's width and its runs row by row below a level of 240 of 255 (.cache/batch15/precision-armament-m4-72/measure.py and ports.py); the end faces where their rims' arcs meet the sides","via":"harvest"},"note":"Counted on the faces that show: the logo's face square to the lens is 128 px wide and the two beside it 87 and 80 px as seen, 0.68 and 0.63 of it: faces turned 45 degrees (cos 45 = 0.71). A regular octagon of 302 px across flats has 125 px faces. The three-quarter photos (1e2ffa21d003, 897181cb9d98) show the faces' corners round the base."}]},"base_length":{"label":"Base (the wrench flats), length from the rear face to where the rear groove begins","kind":"length","measurements":[{"id":"photo","value":0.315,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/precision-armament-m4-72 4edb633eb80e (Precision Armament's gallery, M4-72-SEVERE-DUTY-MUZZLE-BRAKE-SS-FRONT: the stainless one standing, muzzle up, the narrow flat and the logo's flat toward the lens, on white, 1024 x 1024)","scaleRef":"across, the body's own width, 341 px, as od (0.865): 394.2 px/in; along, its end faces 908 px apart as overall_length (2.250): 403.6 px/in","method":"the silhouette's width and its runs row by row below a level of 240 of 255 (.cache/batch15/precision-armament-m4-72/measure.py and ports.py); the end faces where their rims' arcs meet the sides","via":"harvest"},"note":"The silhouette steps from 0.743 to the groove's 0.682 between 0.308 and 0.323; the black photo between 0.313 and 0.323."}]},"base_front_chamfer":{"label":"Base, the chamfer on its front edge (how far back from its front face it reaches the flats)","kind":"length","measurements":[{"id":"photo","value":0.05,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/precision-armament-m4-72 4edb633eb80e (Precision Armament's gallery, M4-72-SEVERE-DUTY-MUZZLE-BRAKE-SS-FRONT: the stainless one standing, muzzle up, the narrow flat and the logo's flat toward the lens, on white, 1024 x 1024)","scaleRef":"across, the body's own width, 341 px, as od (0.865): 394.2 px/in; along, its end faces 908 px apart as overall_length (2.250): 403.6 px/in","method":"the silhouette's width and its runs row by row below a level of 240 of 255 (.cache/batch15/precision-armament-m4-72/measure.py and ports.py); the end faces where their rims' arcs meet the sides","via":"harvest"},"note":"The flats' silhouette (0.766) narrows from 0.26 from the rear face to 0.743 at its front face: a turned chamfer that takes the corners and reaches the flats there."}]},"base_front_r":{"label":"Base, the chamfer's radius at its front face","kind":"length","measurements":[{"id":"photo","value":0.372,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/precision-armament-m4-72 4edb633eb80e (Precision Armament's gallery, M4-72-SEVERE-DUTY-MUZZLE-BRAKE-SS-FRONT: the stainless one standing, muzzle up, the narrow flat and the logo's flat toward the lens, on white, 1024 x 1024)","scaleRef":"across, the body's own width, 341 px, as od (0.865): 394.2 px/in; along, its end faces 908 px apart as overall_length (2.250): 403.6 px/in","method":"the silhouette's width and its runs row by row below a level of 240 of 255 (.cache/batch15/precision-armament-m4-72/measure.py and ports.py); the end faces where their rims' arcs meet the sides","via":"harvest"},"note":"Half the silhouette's 0.743 just behind the groove's rear wall (0.739 in the black photo)."}]},"base_rear_chamfer":{"label":"Base, the chamfer on its rear edge (drawn at 45 degrees)","kind":"length","measurements":[{"id":"photo","value":0.025,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/precision-armament-m4-72 4edb633eb80e (Precision Armament's gallery, M4-72-SEVERE-DUTY-MUZZLE-BRAKE-SS-FRONT: the stainless one standing, muzzle up, the narrow flat and the logo's flat toward the lens, on white, 1024 x 1024)","scaleRef":"across, the body's own width, 341 px, as od (0.865): 394.2 px/in; along, its end faces 908 px apart as overall_length (2.250): 403.6 px/in","method":"the silhouette's width and its runs row by row below a level of 240 of 255 (.cache/batch15/precision-armament-m4-72/measure.py and ports.py); the end faces where their rims' arcs meet the sides","via":"harvest"},"note":"The flats' silhouette comes in 0.04 a side over the last 0.025 in; the rear face's own arc (the lens 2 degrees off its plane, 0.012 in) is mixed into the last rows. A round more than a chamfer by the way it fills in."}]},"groove_d":{"label":"The two grooves either side of the ring, diameter","kind":"length","measurements":[{"id":"photo","value":0.682,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/precision-armament-m4-72 4edb633eb80e (Precision Armament's gallery, M4-72-SEVERE-DUTY-MUZZLE-BRAKE-SS-FRONT: the stainless one standing, muzzle up, the narrow flat and the logo's flat toward the lens, on white, 1024 x 1024)","scaleRef":"across, the body's own width, 341 px, as od (0.865): 394.2 px/in; along, its end faces 908 px apart as overall_length (2.250): 403.6 px/in","method":"the silhouette's width and its runs row by row below a level of 240 of 255 (.cache/batch15/precision-armament-m4-72/measure.py and ports.py); the end faces where their rims' arcs meet the sides","via":"harvest"},"note":"269 px in both grooves."},{"id":"black","value":0.684,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/precision-armament-m4-72 a1a4c479327e (Precision Armament's gallery, M4-72-SEVERE-DUTY-MUZZLE-BRAKE-BLK-FRONT: the black one in the same pose, on white, 1024 x 1024)","scaleRef":"across, the body's 344 px as od (0.865): 397.7 px/in; along, its end faces 913.6 px apart as overall_length (2.250)","method":"as the stainless one's, below a level of 200","via":"harvest"},"note":"272 px in both."}],"adopt":{"from":"photo","reason":"The two photos agree within 0.002 in."}},"ring_rear_x":{"label":"The ring, rear face (from the rear face), where the rear groove ends","kind":"length","measurements":[{"id":"photo","value":0.394,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/precision-armament-m4-72 4edb633eb80e (Precision Armament's gallery, M4-72-SEVERE-DUTY-MUZZLE-BRAKE-SS-FRONT: the stainless one standing, muzzle up, the narrow flat and the logo's flat toward the lens, on white, 1024 x 1024)","scaleRef":"across, the body's own width, 341 px, as od (0.865): 394.2 px/in; along, its end faces 908 px apart as overall_length (2.250): 403.6 px/in","method":"the silhouette's width and its runs row by row below a level of 240 of 255 (.cache/batch15/precision-armament-m4-72/measure.py and ports.py); the end faces where their rims' arcs meet the sides","via":"harvest"},"note":"Midway up the ring's rounded rear edge (0.384 to 0.414); the black photo 0.392."}]},"ring_front_x":{"label":"The ring, front face (from the rear face), where the front groove begins","kind":"length","measurements":[{"id":"photo","value":0.543,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/precision-armament-m4-72 4edb633eb80e (Precision Armament's gallery, M4-72-SEVERE-DUTY-MUZZLE-BRAKE-SS-FRONT: the stainless one standing, muzzle up, the narrow flat and the logo's flat toward the lens, on white, 1024 x 1024)","scaleRef":"across, the body's own width, 341 px, as od (0.865): 394.2 px/in; along, its end faces 908 px apart as overall_length (2.250): 403.6 px/in","method":"the silhouette's width and its runs row by row below a level of 240 of 255 (.cache/batch15/precision-armament-m4-72/measure.py and ports.py); the end faces where their rims' arcs meet the sides","via":"harvest"},"note":"Midway down its rounded front edge (0.523 to 0.553); the black photo 0.545."}]},"body_rear_x":{"label":"The ported body, rear face (from the rear face), where the front groove ends","kind":"length","measurements":[{"id":"photo","value":0.633,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/precision-armament-m4-72 4edb633eb80e (Precision Armament's gallery, M4-72-SEVERE-DUTY-MUZZLE-BRAKE-SS-FRONT: the stainless one standing, muzzle up, the narrow flat and the logo's flat toward the lens, on white, 1024 x 1024)","scaleRef":"across, the body's own width, 341 px, as od (0.865): 394.2 px/in; along, its end faces 908 px apart as overall_length (2.250): 403.6 px/in","method":"the silhouette's width and its runs row by row below a level of 240 of 255 (.cache/batch15/precision-armament-m4-72/measure.py and ports.py); the end faces where their rims' arcs meet the sides","via":"harvest"},"note":"Midway up the body's rounded rear edge (0.622 to 0.652); the black photo 0.633."}]},"edge_round":{"label":"The round on the ring's edges and the body's rear edge","kind":"length","measurements":[{"id":"photo","value":0.02,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/precision-armament-m4-72 4edb633eb80e (Precision Armament's gallery, M4-72-SEVERE-DUTY-MUZZLE-BRAKE-SS-FRONT: the stainless one standing, muzzle up, the narrow flat and the logo's flat toward the lens, on white, 1024 x 1024)","scaleRef":"across, the body's own width, 341 px, as od (0.865): 394.2 px/in; along, its end faces 908 px apart as overall_length (2.250): 403.6 px/in","method":"the silhouette's width and its runs row by row below a level of 240 of 255 (.cache/batch15/precision-armament-m4-72/measure.py and ports.py); the end faces where their rims' arcs meet the sides","via":"harvest"},"note":"Each of those edges takes 0.025 to 0.03 in along the device to come from the groove's width to the full one: drawn as a 45-degree break of this size."}]},"flat_width":{"label":"The narrow flat along the top of the body, width","kind":"length","measurements":[{"id":"photo","value":0.263,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/precision-armament-m4-72 4edb633eb80e (Precision Armament's gallery, M4-72-SEVERE-DUTY-MUZZLE-BRAKE-SS-FRONT: the stainless one standing, muzzle up, the narrow flat and the logo's flat toward the lens, on white, 1024 x 1024)","scaleRef":"across, the body's own width, 341 px, as od (0.865): 394.2 px/in; along, its end faces 908 px apart as overall_length (2.250): 403.6 px/in","method":"the silhouette's width and its runs row by row below a level of 240 of 255 (.cache/batch15/precision-armament-m4-72/measure.py and ports.py); the end faces where their rims' arcs meet the sides","via":"harvest"},"note":"The flat faces the lens: its two edges are lit lines at columns 470 and 573.5 (the mean of rows 560 to 640, where nothing is cut), 103.5 px. It runs from the front face along the body and across the ring, in one plane (Dirty Bird's photo of the stainless one, a055fdfb9f12: the ring has the same flat; the maker's three-quarter photo 1e2ffa21d003). The base's top flat, in line with it, is lower."}],"note":"The installation guide: \"the compensator must be properly 'timed' (indexed) with the narrow flat at the 12 o'clock position (top dead center)\"."},"front_bevel_r":{"label":"The front face's bevel, how far in from the outside it begins on the face","kind":"length","measurements":[{"id":"photo","value":0.072,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/precision-armament-m4-72 4edb633eb80e (Precision Armament's gallery, M4-72-SEVERE-DUTY-MUZZLE-BRAKE-SS-FRONT: the stainless one standing, muzzle up, the narrow flat and the logo's flat toward the lens, on white, 1024 x 1024)","scaleRef":"across, the body's own width, 341 px, as od (0.865): 394.2 px/in; along, its end faces 908 px apart as overall_length (2.250): 403.6 px/in","method":"the silhouette's width and its runs row by row below a level of 240 of 255 (.cache/batch15/precision-armament-m4-72/measure.py and ports.py); the end faces where their rims' arcs meet the sides","via":"harvest"},"note":"The silhouette is 0.72 wide at the front face, 0.865 from 0.037 behind it. The three-quarter photo 1e2ffa21d003 shows the bevel as a band round the face's rim."}]},"front_bevel_len":{"label":"The front face's bevel, length along the device","kind":"length","measurements":[{"id":"photo","value":0.037,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/precision-armament-m4-72 4edb633eb80e (Precision Armament's gallery, M4-72-SEVERE-DUTY-MUZZLE-BRAKE-SS-FRONT: the stainless one standing, muzzle up, the narrow flat and the logo's flat toward the lens, on white, 1024 x 1024)","scaleRef":"across, the body's own width, 341 px, as od (0.865): 394.2 px/in; along, its end faces 908 px apart as overall_length (2.250): 403.6 px/in","method":"the silhouette's width and its runs row by row below a level of 240 of 255 (.cache/batch15/precision-armament-m4-72/measure.py and ports.py); the end faces where their rims' arcs meet the sides","via":"harvest"}}]},"ports":{"label":"Ports, on each side","kind":"count","measurements":[{"id":"photo","value":3,"unit":"count","source":{"type":"photo","photo":"references/precision-armament-m4-72 4edb633eb80e (Precision Armament's gallery, M4-72-SEVERE-DUTY-MUZZLE-BRAKE-SS-FRONT: the stainless one standing, muzzle up, the narrow flat and the logo's flat toward the lens, on white, 1024 x 1024)","scaleRef":"across, the body's own width, 341 px, as od (0.865): 394.2 px/in; along, its end faces 908 px apart as overall_length (2.250): 403.6 px/in","method":"the silhouette's width and its runs row by row below a level of 240 of 255 (.cache/batch15/precision-armament-m4-72/measure.py and ports.py); the end faces where their rims' arcs meet the sides","via":"harvest"},"note":"Three notches in each edge of the silhouette, the same on both sides, and so three baffles, the metal ahead of each port (the two teeth between the ports and the front cap): the maker's \"triple baffle\"; the side views on file (the spec sheet's render, the maker's photos of it on rifles, 4bea0a4d253a and 8de74efed3c5) have three ports in the side toward the lens, the front one open through the device. Nothing in the top or the bottom."}],"note":"The maker: \"Innovative reverse venting triple baffle design\"; \"Side vents are precisely canted upward to eliminate muzzle climb\" (spec sheet); \"Closed bottom construction combined with upward biased venting\" (page)."},"port_z_in":{"label":"Ports, how far in from the axis each side's notch reaches (its inner end)","kind":"length","measurements":[{"id":"photo","value":0.215,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/precision-armament-m4-72 4edb633eb80e (Precision Armament's gallery, M4-72-SEVERE-DUTY-MUZZLE-BRAKE-SS-FRONT: the stainless one standing, muzzle up, the narrow flat and the logo's flat toward the lens, on white, 1024 x 1024)","scaleRef":"across, the body's own width, 341 px, as od (0.865): 394.2 px/in; along, its end faces 908 px apart as overall_length (2.250): 403.6 px/in","method":"the silhouette's width and its runs row by row below a level of 240 of 255 (.cache/batch15/precision-armament-m4-72/measure.py and ports.py); the end faces where their rims' arcs meet the sides","via":"harvest"},"note":"Every port, both photos, both sides: no gap is left at 0.20 from the axis and every one has one at 0.22."}]},"port_end_r":{"label":"Ports, the round of the notch's inner corners","kind":"length","measurements":[{"id":"photo","value":0.04,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/precision-armament-m4-72 4edb633eb80e (Precision Armament's gallery, M4-72-SEVERE-DUTY-MUZZLE-BRAKE-SS-FRONT: the stainless one standing, muzzle up, the narrow flat and the logo's flat toward the lens, on white, 1024 x 1024)","scaleRef":"across, the body's own width, 341 px, as od (0.865): 394.2 px/in; along, its end faces 908 px apart as overall_length (2.250): 403.6 px/in","method":"the silhouette's width and its runs row by row below a level of 240 of 255 (.cache/batch15/precision-armament-m4-72/measure.py and ports.py); the end faces where their rims' arcs meet the sides","via":"harvest"},"note":"Each notch narrows over its last 0.03 to 0.05 in toward its inner end (at 0.22 from the axis 0.04 of a 0.1 span is left)."}]},"port_rear_angle":{"label":"Ports, the rear wall's lean from square across the device (it moves forward going inward)","kind":"angle","measurements":[{"id":"photo","value":54.7,"unit":"deg","pm":1.5,"source":{"type":"photo","photo":"references/precision-armament-m4-72 4edb633eb80e (Precision Armament's gallery, M4-72-SEVERE-DUTY-MUZZLE-BRAKE-SS-FRONT: the stainless one standing, muzzle up, the narrow flat and the logo's flat toward the lens, on white, 1024 x 1024)","scaleRef":"across, the body's own width, 341 px, as od (0.865): 394.2 px/in; along, its end faces 908 px apart as overall_length (2.250): 403.6 px/in","method":"the silhouette's width and its runs row by row below a level of 240 of 255 (.cache/batch15/precision-armament-m4-72/measure.py and ports.py); the end faces where their rims' arcs meet the sides","via":"harvest"},"note":"A line through each rear wall from 0.26 to 0.43 from the axis, both photos, both sides (36 points a port): forward 1.456, 1.365 and 1.412 in for an inch inward (55.5, 53.8 and 54.7 degrees from square), rms 0.006 to 0.012 in."}],"note":"The rear wall leans back going outward, which is the reverse venting."},"port_front_angle":{"label":"Ports, the front wall's lean from square (the first two ports)","kind":"angle","measurements":[{"id":"photo","value":30.3,"unit":"deg","pm":1.5,"source":{"type":"photo","photo":"references/precision-armament-m4-72 4edb633eb80e (Precision Armament's gallery, M4-72-SEVERE-DUTY-MUZZLE-BRAKE-SS-FRONT: the stainless one standing, muzzle up, the narrow flat and the logo's flat toward the lens, on white, 1024 x 1024)","scaleRef":"across, the body's own width, 341 px, as od (0.865): 394.2 px/in; along, its end faces 908 px apart as overall_length (2.250): 403.6 px/in","method":"the silhouette's width and its runs row by row below a level of 240 of 255 (.cache/batch15/precision-armament-m4-72/measure.py and ports.py); the end faces where their rims' arcs meet the sides","via":"harvest"},"note":"From 0.30 to 0.43 from the axis: forward 0.558 and 0.613 in for an inch inward (29.2 and 31.5 degrees), rms 0.002 in. The third port's front wall is square across (-3.8 degrees, within its reading), the front cap's rear face."}]},"port_1_rear_x":{"label":"Port 1 (the rearmost), rear wall at the outside (from the rear face)","kind":"length","measurements":[{"id":"photo","value":0.774,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/precision-armament-m4-72 4edb633eb80e (Precision Armament's gallery, M4-72-SEVERE-DUTY-MUZZLE-BRAKE-SS-FRONT: the stainless one standing, muzzle up, the narrow flat and the logo's flat toward the lens, on white, 1024 x 1024)","scaleRef":"across, the body's own width, 341 px, as od (0.865): 394.2 px/in; along, its end faces 908 px apart as overall_length (2.250): 403.6 px/in","method":"the silhouette's width and its runs row by row below a level of 240 of 255 (.cache/batch15/precision-armament-m4-72/measure.py and ports.py); the end faces where their rims' arcs meet the sides","via":"harvest"}}]},"port_1_front_x":{"label":"Port 1, front wall at the outside","kind":"length","measurements":[{"id":"photo","value":1.054,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/precision-armament-m4-72 4edb633eb80e (Precision Armament's gallery, M4-72-SEVERE-DUTY-MUZZLE-BRAKE-SS-FRONT: the stainless one standing, muzzle up, the narrow flat and the logo's flat toward the lens, on white, 1024 x 1024)","scaleRef":"across, the body's own width, 341 px, as od (0.865): 394.2 px/in; along, its end faces 908 px apart as overall_length (2.250): 403.6 px/in","method":"the silhouette's width and its runs row by row below a level of 240 of 255 (.cache/batch15/precision-armament-m4-72/measure.py and ports.py); the end faces where their rims' arcs meet the sides","via":"harvest"}}]},"port_2_rear_x":{"label":"Port 2, rear wall at the outside","kind":"length","measurements":[{"id":"photo","value":1.195,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/precision-armament-m4-72 4edb633eb80e (Precision Armament's gallery, M4-72-SEVERE-DUTY-MUZZLE-BRAKE-SS-FRONT: the stainless one standing, muzzle up, the narrow flat and the logo's flat toward the lens, on white, 1024 x 1024)","scaleRef":"across, the body's own width, 341 px, as od (0.865): 394.2 px/in; along, its end faces 908 px apart as overall_length (2.250): 403.6 px/in","method":"the silhouette's width and its runs row by row below a level of 240 of 255 (.cache/batch15/precision-armament-m4-72/measure.py and ports.py); the end faces where their rims' arcs meet the sides","via":"harvest"}}]},"port_2_front_x":{"label":"Port 2, front wall at the outside","kind":"length","measurements":[{"id":"photo","value":1.482,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/precision-armament-m4-72 4edb633eb80e (Precision Armament's gallery, M4-72-SEVERE-DUTY-MUZZLE-BRAKE-SS-FRONT: the stainless one standing, muzzle up, the narrow flat and the logo's flat toward the lens, on white, 1024 x 1024)","scaleRef":"across, the body's own width, 341 px, as od (0.865): 394.2 px/in; along, its end faces 908 px apart as overall_length (2.250): 403.6 px/in","method":"the silhouette's width and its runs row by row below a level of 240 of 255 (.cache/batch15/precision-armament-m4-72/measure.py and ports.py); the end faces where their rims' arcs meet the sides","via":"harvest"}}]},"port_3_rear_x":{"label":"Port 3 (the front one), rear wall at the outside","kind":"length","measurements":[{"id":"photo","value":1.607,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/precision-armament-m4-72 4edb633eb80e (Precision Armament's gallery, M4-72-SEVERE-DUTY-MUZZLE-BRAKE-SS-FRONT: the stainless one standing, muzzle up, the narrow flat and the logo's flat toward the lens, on white, 1024 x 1024)","scaleRef":"across, the body's own width, 341 px, as od (0.865): 394.2 px/in; along, its end faces 908 px apart as overall_length (2.250): 403.6 px/in","method":"the silhouette's width and its runs row by row below a level of 240 of 255 (.cache/batch15/precision-armament-m4-72/measure.py and ports.py); the end faces where their rims' arcs meet the sides","via":"harvest"}}]},"port_3_front_x":{"label":"Port 3, front wall (square across: the front cap's rear face)","kind":"length","measurements":[{"id":"photo","value":2.121,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/precision-armament-m4-72 4edb633eb80e (Precision Armament's gallery, M4-72-SEVERE-DUTY-MUZZLE-BRAKE-SS-FRONT: the stainless one standing, muzzle up, the narrow flat and the logo's flat toward the lens, on white, 1024 x 1024)","scaleRef":"across, the body's own width, 341 px, as od (0.865): 394.2 px/in; along, its end faces 908 px apart as overall_length (2.250): 403.6 px/in","method":"the silhouette's width and its runs row by row below a level of 240 of 255 (.cache/batch15/precision-armament-m4-72/measure.py and ports.py); the end faces where their rims' arcs meet the sides","via":"harvest"}}]},"window_1_x0":{"label":"Port 1's opening through the device seen from the side: rear end (from the rear face)","kind":"length","measurements":[{"id":"render","value":0.926,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/precision-armament-m4-72 docs/05934027e8.pdf (Precision Armament's spec sheet, its second render: the device from the top above, from the side below, 825 x 720 as embedded)","scaleRef":"along, each view's 639 px between the end faces as overall_length (2.250); across, the side view's body, 226 px, as od (0.865)","method":"light pixels (above 150 of 255) inside the side view's body, column by column; positions along mapped by the port's own two walls in the top view, as each port's fraction (the render's views are in perspective: the device reads 5.6% long at one scale)","via":"harvest"},"note":"Render x 0.887, 0.54 of the port."}],"note":"From the side the ports show the light through the device in their front halves, higher than the axis in the first two (the vents \"canted upward\"). Read on the spec sheet's render, whose side view has them square on; mapped into the photos' frame by each port's own ends in the render's top view (rear wall 0.750, front 1.003 there; 0.774 and 1.054 here)."},"window_1_x1":{"label":"Port 1's opening: front end","kind":"length","measurements":[{"id":"render","value":1.051,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/precision-armament-m4-72 docs/05934027e8.pdf (Precision Armament's spec sheet, its second render: the device from the top above, from the side below, 825 x 720 as embedded)","scaleRef":"along, each view's 639 px between the end faces as overall_length (2.250); across, the side view's body, 226 px, as od (0.865)","method":"light pixels (above 150 of 255) inside the side view's body, column by column; positions along mapped by the port's own two walls in the top view, as each port's fraction (the render's views are in perspective: the device reads 5.6% long at one scale)","via":"harvest"},"note":"Render x 1.000, 0.99 of the port: at the front wall."}]},"window_1_y0":{"label":"Port 1's opening: its lower edge (from the axis)","kind":"length","measurements":[{"id":"render","value":-0.14,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/precision-armament-m4-72 docs/05934027e8.pdf (Precision Armament's spec sheet, its second render: the device from the top above, from the side below, 825 x 720 as embedded)","scaleRef":"along, each view's 639 px between the end faces as overall_length (2.250); across, the side view's body, 226 px, as od (0.865)","method":"light pixels (above 150 of 255) inside the side view's body, column by column; positions along mapped by the port's own two walls in the top view, as each port's fraction (the render's views are in perspective: the device reads 5.6% long at one scale)","via":"harvest"}}]},"window_1_y1":{"label":"Port 1's opening: its upper edge (from the axis)","kind":"length","measurements":[{"id":"render","value":0.232,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/precision-armament-m4-72 docs/05934027e8.pdf (Precision Armament's spec sheet, its second render: the device from the top above, from the side below, 825 x 720 as embedded)","scaleRef":"along, each view's 639 px between the end faces as overall_length (2.250); across, the side view's body, 226 px, as od (0.865)","method":"light pixels (above 150 of 255) inside the side view's body, column by column; positions along mapped by the port's own two walls in the top view, as each port's fraction (the render's views are in perspective: the device reads 5.6% long at one scale)","via":"harvest"}}]},"window_2_x0":{"label":"Port 2's opening: rear end","kind":"length","measurements":[{"id":"render","value":1.327,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/precision-armament-m4-72 docs/05934027e8.pdf (Precision Armament's spec sheet, its second render: the device from the top above, from the side below, 825 x 720 as embedded)","scaleRef":"along, each view's 639 px between the end faces as overall_length (2.250); across, the side view's body, 226 px, as od (0.865)","method":"light pixels (above 150 of 255) inside the side view's body, column by column; positions along mapped by the port's own two walls in the top view, as each port's fraction (the render's views are in perspective: the device reads 5.6% long at one scale)","via":"harvest"},"note":"Render x 1.268 of a port from 1.134 to 1.426."}]},"window_2_x1":{"label":"Port 2's opening: front end","kind":"length","measurements":[{"id":"render","value":1.482,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/precision-armament-m4-72 docs/05934027e8.pdf (Precision Armament's spec sheet, its second render: the device from the top above, from the side below, 825 x 720 as embedded)","scaleRef":"along, each view's 639 px between the end faces as overall_length (2.250); across, the side view's body, 226 px, as od (0.865)","method":"light pixels (above 150 of 255) inside the side view's body, column by column; positions along mapped by the port's own two walls in the top view, as each port's fraction (the render's views are in perspective: the device reads 5.6% long at one scale)","via":"harvest"},"note":"Render x 1.437, at the front wall (1.04 of the port by the render's top view): taken as the wall."}]},"window_2_y0":{"label":"Port 2's opening: lower edge","kind":"length","measurements":[{"id":"render","value":-0.147,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/precision-armament-m4-72 docs/05934027e8.pdf (Precision Armament's spec sheet, its second render: the device from the top above, from the side below, 825 x 720 as embedded)","scaleRef":"along, each view's 639 px between the end faces as overall_length (2.250); across, the side view's body, 226 px, as od (0.865)","method":"light pixels (above 150 of 255) inside the side view's body, column by column; positions along mapped by the port's own two walls in the top view, as each port's fraction (the render's views are in perspective: the device reads 5.6% long at one scale)","via":"harvest"}}]},"window_2_y1":{"label":"Port 2's opening: upper edge","kind":"length","measurements":[{"id":"render","value":0.239,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/precision-armament-m4-72 docs/05934027e8.pdf (Precision Armament's spec sheet, its second render: the device from the top above, from the side below, 825 x 720 as embedded)","scaleRef":"along, each view's 639 px between the end faces as overall_length (2.250); across, the side view's body, 226 px, as od (0.865)","method":"light pixels (above 150 of 255) inside the side view's body, column by column; positions along mapped by the port's own two walls in the top view, as each port's fraction (the render's views are in perspective: the device reads 5.6% long at one scale)","via":"harvest"}}]},"window_3_x0":{"label":"Port 3's opening: rear end","kind":"length","measurements":[{"id":"render","value":1.781,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/precision-armament-m4-72 docs/05934027e8.pdf (Precision Armament's spec sheet, its second render: the device from the top above, from the side below, 825 x 720 as embedded)","scaleRef":"along, each view's 639 px between the end faces as overall_length (2.250); across, the side view's body, 226 px, as od (0.865)","method":"light pixels (above 150 of 255) inside the side view's body, column by column; positions along mapped by the port's own two walls in the top view, as each port's fraction (the render's views are in perspective: the device reads 5.6% long at one scale)","via":"harvest"},"note":"Render x 1.746 of a port from 1.567 to 2.095."}]},"window_3_x1":{"label":"Port 3's opening: front end","kind":"length","measurements":[{"id":"render","value":2.07,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/precision-armament-m4-72 docs/05934027e8.pdf (Precision Armament's spec sheet, its second render: the device from the top above, from the side below, 825 x 720 as embedded)","scaleRef":"along, each view's 639 px between the end faces as overall_length (2.250); across, the side view's body, 226 px, as od (0.865)","method":"light pixels (above 150 of 255) inside the side view's body, column by column; positions along mapped by the port's own two walls in the top view, as each port's fraction (the render's views are in perspective: the device reads 5.6% long at one scale)","via":"harvest"},"note":"Render x 2.042."}]},"window_3_y0":{"label":"Port 3's opening: lower edge","kind":"length","measurements":[{"id":"render","value":-0.285,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/precision-armament-m4-72 docs/05934027e8.pdf (Precision Armament's spec sheet, its second render: the device from the top above, from the side below, 825 x 720 as embedded)","scaleRef":"along, each view's 639 px between the end faces as overall_length (2.250); across, the side view's body, 226 px, as od (0.865)","method":"light pixels (above 150 of 255) inside the side view's body, column by column; positions along mapped by the port's own two walls in the top view, as each port's fraction (the render's views are in perspective: the device reads 5.6% long at one scale)","via":"harvest"}}]},"window_3_y1":{"label":"Port 3's opening: upper edge","kind":"length","measurements":[{"id":"render","value":0.277,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/precision-armament-m4-72 docs/05934027e8.pdf (Precision Armament's spec sheet, its second render: the device from the top above, from the side below, 825 x 720 as embedded)","scaleRef":"along, each view's 639 px between the end faces as overall_length (2.250); across, the side view's body, 226 px, as od (0.865)","method":"light pixels (above 150 of 255) inside the side view's body, column by column; positions along mapped by the port's own two walls in the top view, as each port's fraction (the render's views are in perspective: the device reads 5.6% long at one scale)","via":"harvest"}}]},"window_r":{"label":"The openings' corners, round","kind":"length","measurements":[{"id":"render","value":0.06,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/precision-armament-m4-72 docs/05934027e8.pdf (Precision Armament's spec sheet, its second render: the device from the top above, from the side below, 825 x 720 as embedded)","scaleRef":"along, each view's 639 px between the end faces as overall_length (2.250); across, the side view's body, 226 px, as od (0.865)","method":"light pixels (above 150 of 255) inside the side view's body, column by column; positions along mapped by the port's own two walls in the top view, as each port's fraction (the render's views are in perspective: the device reads 5.6% long at one scale)","via":"harvest"},"note":"Port 1's opening is 0.16 high at its rear end and its full 0.37 0.06 in further on: a round end. The maker's photos on rifles (4bea0a4d253a, 8de74efed3c5) show the front one as a rectangle with round corners."}]},"chamber_d":{"label":"The chambers between the baffles, diameter, as drawn","kind":"length","measurements":[{"id":"assumed","value":0.562,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{.window_3_y1} - {.window_3_y0}","basis":"An assumption for the drawing, not a reading of the chambers: the front port's opening as the render shows it from the side.","via":"harvest"}}],"note":"NOT SOURCED as a size: no view on file looks inside. The maker: \"Innovative reverse venting triple baffle design\". The front port's opening, seen from the side on the spec sheet's render, is 0.56 tall across the axis, and the three-quarter photo 1e2ffa21d003 shows through that port a baffle with the hole in it: each chamber is drawn that wide, from its port's rear wall to its front wall at the outside. Without them the model is 3.40 oz of 416 stainless for a part the maker weighs at 2.6."},"edge_break":{"label":"The break on every machined edge, as drawn","kind":"length","measurements":[{"id":"assumed","value":0.006,"unit":"in","pm":0.003,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows an edge's break in profile at this size; the same break SureFire's WARCOMP is drawn with.","via":"harvest"}}],"note":"NOT SOURCED: a construction of the drawing, so that the edges catch the light as a machined part's do."},"bore_d":{"label":"The hole through, at the front face","kind":"length","measurements":[{"id":"photo","value":0.29,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/precision-armament-m4-72 1e2ffa21d003 (Precision Armament's gallery, M4-72: the black one standing, seen from above its muzzle and to one side, 1024 x 1024)","scaleRef":"the front face's own width across its ellipse's long axis (365 px) as od (0.865), the hole's mouth and the face in one plane","method":"the dark of the hole across the same axis, 122 px, by eye on a crop at twice size; a chamfer at its mouth would read large","via":"harvest"}}],"note":"The installation guide: \"RECOMMENDED MINIMUM BORE CLEARANCE IS 0.030” OVER BULLET DIAMETER\"."},"thread_major_d":{"label":"The thread it is cut for: major diameter","kind":"length","measurements":[{"id":"tdp","value":0.4957,"unit":"in","pm":0.0033,"stated":"1/2-28 UNEF-2A MAJOR DIA .4989/.4924","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213","via":"user"}}],"note":"The maker: \"Thread Size 1/2x28\" (spec sheet), \".223/5.56mm model is designed to fit M4/M16/AR15 style rifles and features 1/2-28 threads\" (page), \"M4-72-556 | .223 | 1/2-28 RH\" (the installation guide's table). The Army barrel's 1/2-28, as the catalog's barrels are drawn."},"thread_minor_d":{"label":"The thread it is cut for: minor diameter","kind":"length","measurements":[{"id":"tdp","value":0.4551,"unit":"in","pm":0.002,"stated":"MINOR DIA .4551 MAX","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213","via":"user"}}]},"thread_pitch":{"label":"The thread it is cut for: pitch","kind":"length","measurements":[{"id":"tdp","value":0.03571,"unit":"in","pm":0.00005,"stated":"1/2-28 UNEF-2A","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213","via":"user"}}]},"thread_depth":{"label":"Threaded hole's depth from the rear face, as drawn","kind":"length","measurements":[{"id":"as-a2","value":0.69,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{a2-flash-hider.thread_depth}","basis":"An assumption for the drawing, not a reading: the depth of the Army compensator's threaded bore (drawing 9349051).","via":"user"}}],"note":"NOT SOURCED for this device: no page, drawing or photo on file looks into its rear end. Drawn as deep as the Army compensator's, which the same barrels take: it ends behind the first port and under the ring's front groove."}}},{"subject":"primary-arms-deluxe-30mm-mount","title":"Primary Arms Deluxe AR-15 Scope Mount - 30mm","dimensions":{"optical_axis_above_rail":{"label":"Ring axis above the rail's top","kind":"length","measurements":[{"id":"page","value":1.5,"unit":"in","pm":0.05,"stated":"Places the center of your 30mm tube scope 1.5 inches above the rail.","source":{"type":"spec","publisher":"manufacturer","name":"Primary Arms, Deluxe AR-15 Scope Mount - 30mm (PADLXSM), product page","url":"https://www.primaryarms.com/primary-arms-deluxe-ar15-scope-mount-30mm-padlxsm","retrieved":"2026-10-13","via":"harvest"}},{"id":"kygunco","value":1.5,"unit":"in","pm":0.005,"stated":"Central Height: 1.50","source":{"type":"spec","publisher":"retailer","name":"KYGUNCO, PRIMARY ARMS Deluxe AR-15 Scope Mount 30mm (PRM-910058)","url":"https://kygunco.com/product/primary-arms-padlxsm-deluxe-ar15-scope-mount-30mm","retrieved":"2026-10-13","via":"harvest"}},{"id":"armamat","value":1.5,"unit":"in","pm":0.05,"stated":"The integrated riser places the center of the tube 1.5”/38mm above the rail.","source":{"type":"spec","publisher":"retailer","name":"Armamat, Primary Arms Deluxe Scope Mount - 30mm (manufacturer number PADLXSM)","url":"https://www.armamat.com/en/p/deluxe-scope-mount-30mm-113267/","retrieved":"2026-10-13","via":"harvest"}},{"id":"review","value":1.5,"unit":"in","pm":0.05,"stated":"It places the center of the scope exactly 1.5 inches above the rail,","source":{"type":"spec","publisher":"review","name":"The Truth About Guns, Gear Review: Primary Arms Deluxe AR15 Scope Mount (March 31, 2012; the reviewer's own unit)","url":"https://www.thetruthaboutguns.com/gear-review-primary-arms-deluxe-ar15-scope-mount/","retrieved":"2026-10-13","via":"harvest"}}],"adopt":{"from":"page","reason":"The maker's own sentence; two sellers and a reviewer say the same."}},"ring_bore":{"label":"Tube diameter the rings are bored for","kind":"length","measurements":[{"id":"page","value":30,"unit":"mm","stated":"Fits scopes with 30mm tubes.","source":{"type":"spec","publisher":"manufacturer","name":"Primary Arms, Deluxe AR-15 Scope Mount - 30mm (PADLXSM), product page","url":"https://www.primaryarms.com/primary-arms-deluxe-ar15-scope-mount-30mm-padlxsm","retrieved":"2026-10-13","via":"harvest"},"note":"Its table: \"Mount Compatibility 30mm\". The 1 in mount is another number (PADLXSM1), not read."},{"id":"armamat","value":30,"unit":"mm","stated":"The optic mount is made of a Picatinny base with two 30mm scope rings with a 2.52”/64mm spread.","source":{"type":"spec","publisher":"retailer","name":"Armamat, Primary Arms Deluxe Scope Mount - 30mm (manufacturer number PADLXSM)","url":"https://www.armamat.com/en/p/deluxe-scope-mount-30mm-113267/","retrieved":"2026-10-13","via":"harvest"}}],"adopt":{"from":"page","reason":"The maker's own sentence; a seller says the same."}},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"page","value":8.2,"unit":"oz","stated":"Weight 8.2 Oz","source":{"type":"spec","publisher":"manufacturer","name":"Primary Arms, Deluxe AR-15 Scope Mount - 30mm (PADLXSM), product page","url":"https://www.primaryarms.com/primary-arms-deluxe-ar15-scope-mount-30mm-padlxsm","retrieved":"2026-10-13","via":"harvest"}},{"id":"kygunco","value":8.2,"unit":"oz","stated":"Weight: 8.2 Oz","source":{"type":"spec","publisher":"retailer","name":"KYGUNCO, PRIMARY ARMS Deluxe AR-15 Scope Mount 30mm (PRM-910058)","url":"https://kygunco.com/product/primary-arms-padlxsm-deluxe-ar15-scope-mount-30mm","retrieved":"2026-10-13","via":"harvest"}},{"id":"ar15discounts","value":8,"unit":"oz","stated":"Weight 8 oz","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, Primary Arms Deluxe AR-15 Scope Mount - 30mm - PADLXSM (Additional information)","url":"https://ar15discounts.com/products/primary-arms-deluxe-ar-15-scope-mount-30mm/","retrieved":"2026-10-13","via":"harvest"},"note":"A whole number: 8.2 rounds to it."},{"id":"review","value":7.3,"unit":"oz","stated":"The 7.3 ounce Primary Arms mount is 3.1 ounces lighter (!) than the rig it’s replacing,","source":{"type":"spec","publisher":"review","name":"The Truth About Guns, Gear Review: Primary Arms Deluxe AR15 Scope Mount (March 31, 2012; the reviewer's own unit)","url":"https://www.thetruthaboutguns.com/gear-review-primary-arms-deluxe-ar15-scope-mount/","retrieved":"2026-10-13","via":"harvest"},"note":"Weighed by the reviewer: his photo (references/primary-arms-deluxe-30mm-mount 5cade1e65db9) has the mount on a kitchen scale reading 7.3. A 2012 unit, of the design the gallery shows today."},{"id":"armamat","value":0.198,"unit":"kg","stated":"Weight: 0.198 kg","source":{"type":"spec","publisher":"retailer","name":"Armamat, Primary Arms Deluxe Scope Mount - 30mm (manufacturer number PADLXSM)","url":"https://www.armamat.com/en/p/deluxe-scope-mount-30mm-113267/","retrieved":"2026-10-13","via":"harvest"},"note":"6.98 oz; the same table gives \"Weight packed: 0.245 kg\" apart, so this isn't the carton's."}],"adopt":{"from":"page","reason":"The maker's own figure, repeated by two of its sellers. A reviewer's scale and a European shop's table read 0.9 and 1.2 oz less: kept beside it, a visible conflict, since nothing on file says what the maker's figure includes."},"note":"The maker's 8.2 oz stands against two figures about an ounce under it, one of them a reviewer's own scale (his photo of the mount on it reads 7.3) and one a shop's table that gives the packed weight apart. As modelled, its aluminium and its steel hardware come to the lighter figures (the part's test holds the model's volume to them)."},"ring_clearance":{"label":"Between the two rings, face to face","kind":"length","measurements":[{"id":"page","value":2.52,"unit":"in","stated":"2.52 inches of clearance between the rings.","source":{"type":"spec","publisher":"manufacturer","name":"Primary Arms, Deluxe AR-15 Scope Mount - 30mm (PADLXSM), product page","url":"https://www.primaryarms.com/primary-arms-deluxe-ar15-scope-mount-30mm-padlxsm","retrieved":"2026-10-13","via":"harvest"}},{"id":"armamat","value":2.52,"unit":"in","stated":"The optic mount is made of a Picatinny base with two 30mm scope rings with a 2.52”/64mm spread.","source":{"type":"spec","publisher":"retailer","name":"Armamat, Primary Arms Deluxe Scope Mount - 30mm (manufacturer number PADLXSM)","url":"https://www.armamat.com/en/p/deluxe-scope-mount-30mm-113267/","retrieved":"2026-10-13","via":"harvest"}},{"id":"review","value":2.5,"unit":"in","pm":0.05,"stated":"The Primary Arms mount is 5.2 inches long overall, and there’s 2.5 inches of clearance between the front and rear rings.","source":{"type":"spec","publisher":"review","name":"The Truth About Guns, Gear Review: Primary Arms Deluxe AR15 Scope Mount (March 31, 2012; the reviewer's own unit)","url":"https://www.thetruthaboutguns.com/gear-review-primary-arms-deluxe-ar15-scope-mount/","retrieved":"2026-10-13","via":"harvest"}},{"id":"left","value":2.572,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount edbba62833fd (Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334)","scaleRef":"a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm","method":"the rings' near side flats' inner ends, columns 352.7 and 1185.2 (level 128), at the near flats' scale: flat to flat. Each flat ends at its edge's break, short of the face","via":"harvest"}}],"adopt":{"from":"page","reason":"The maker's figure, face to face. The photo reads the flats 0.05 in further apart, which is their edges' breaks: taken so (ring_edge_break)."}},"ring_edge_break":{"label":"Rings, the break on the edge between an end face and a side flat","kind":"length","measurements":[{"id":"left","value":0.026,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount edbba62833fd (Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334)","scaleRef":"a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm","method":"worked out, not read as an edge: half of what the near flats stand further apart (2.572 in, ring_clearance's photo reading) than the maker's 2.52 between the rings. The picture has a lit line 8 px wide down each of those edges","via":"harvest"}}]},"ring_length":{"label":"Each ring's length along the tube (face to face)","kind":"length","measurements":[{"id":"left","value":0.693,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount edbba62833fd (Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334)","scaleRef":"a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm","method":"each ring's near side flat, 207.2 px (columns 145.5 to 352.7) and 207.3 px (1185.2 to 1392.5) at rows 500 to 600: 0.641 in at the near flats' scale, and an edge break at each end (ring_edge_break, twice)","via":"harvest"}}]},"ring_rear_x":{"label":"Rear ring, its middle ahead of the rear cross bolt","kind":"length","measurements":[{"id":"left","value":1.435,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount edbba62833fd (Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334)","scaleRef":"a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm","method":"the rear ring's near side flat, columns 1185.2 to 1392.5: its middle, 0.624 in from the lens's axis at the near flats' scale; the rear cross bolt's stud end (the right-hand nut's middle, column 1770) is 2.059 in from the axis at the scale of where it stands. The ± is the nut's place out from the mid-plane (1.1 to 1.3 in) and the pick of the stud's middle","via":"harvest"}}]},"ring_front_x":{"label":"Front ring, its middle ahead of the rear cross bolt","kind":"length","measurements":[{"id":"left","value":4.65,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount edbba62833fd (Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334)","scaleRef":"a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm","method":"the front ring's near side flat, columns 145.5 to 352.7: its middle (as ring_rear_x). The two middles are 3.215 in apart: the maker's 2.52 between the rings and one ring's length (0.693) make 3.213","via":"harvest"}}]},"overall_length":{"label":"Overall length, the base's rear end to the front ring's front face","kind":"length","measurements":[{"id":"armamat","value":13.7,"unit":"cm","stated":"Length: 13.7 cm","source":{"type":"spec","publisher":"retailer","name":"Armamat, Primary Arms Deluxe Scope Mount - 30mm (manufacturer number PADLXSM)","url":"https://www.armamat.com/en/p/deluxe-scope-mount-30mm-113267/","retrieved":"2026-10-13","via":"harvest"},"note":"5.39 in. The shop's own table (\"Packaging Dimensions & Weight\", with the packed sizes given apart); whose measuring it is the page doesn't say."},{"id":"review","value":5.2,"unit":"in","pm":0.05,"stated":"The Primary Arms mount is 5.2 inches long overall, and there’s 2.5 inches of clearance between the front and rear rings.","source":{"type":"spec","publisher":"review","name":"The Truth About Guns, Gear Review: Primary Arms Deluxe AR15 Scope Mount (March 31, 2012; the reviewer's own unit)","url":"https://www.thetruthaboutguns.com/gear-review-primary-arms-deluxe-ar15-scope-mount/","retrieved":"2026-10-13","via":"harvest"},"note":"A 2012 unit, the reviewer's own measuring. The same sentence rounds the maker's 2.52 to 2.5."},{"id":"left","value":5.39,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount edbba62833fd (Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334)","scaleRef":"a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm","method":"the front ring's front face (its near flat's front end, column 145.5, and an edge break) to the clamp bar's rear end (column 1881), each at the scale of where it stands","via":"harvest"}}],"adopt":{"from":"armamat","reason":"A shop's stated length, and the photo read through its own camera comes to the same 5.39 in without having been set by it. The 2012 review's 5.2 is 0.2 short of both: kept, a visible conflict (an older unit, or a quick rule)."}},"overall_width":{"label":"Overall width (across the nuts and the bolts' heads)","kind":"length","measurements":[{"id":"armamat","value":5,"unit":"cm","stated":"Width: 5 cm","source":{"type":"spec","publisher":"retailer","name":"Armamat, Primary Arms Deluxe Scope Mount - 30mm (manufacturer number PADLXSM)","url":"https://www.armamat.com/en/p/deluxe-scope-mount-30mm-113267/","retrieved":"2026-10-13","via":"harvest"},"note":"1.97 in, a whole number of centimetres. As modelled the nuts' ends are 1.12 in left of the middle and the rings' flats 0.79 right: 1.91."}]},"overall_height":{"label":"Overall height","kind":"length","measurements":[{"id":"armamat","value":6.5,"unit":"cm","stated":"Height: 6.5 cm","source":{"type":"spec","publisher":"retailer","name":"Armamat, Primary Arms Deluxe Scope Mount - 30mm (manufacturer number PADLXSM)","url":"https://www.armamat.com/en/p/deluxe-scope-mount-30mm-113267/","retrieved":"2026-10-13","via":"harvest"},"note":"2.56 in, to half a centimetre. As modelled, from the nuts' lowest corners (0.29 under the rail's top) to the caps' tops (2.15 over it): 2.44."}]},"ring_width":{"label":"Rings, across their side flats","kind":"length","measurements":[{"id":"end","value":1.585,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount 424d97f623ad (Armamat 113267060_3.jpg, the mount alone from the front left and above, the front ring's front face toward the lens, 4200 x 2940)","scaleRef":"the front ring's front face in its own plane (a long lens: the background is out of focus): along the split between the cap and the lower half, 940 px/in by the 30 mm bore's chord there (1073.5 px from rim to rim; the split is 0.15 in above the bore's centre, so the chord is 1.142 in); up the face 801 px/in, by the lower half's side flat (463 px, the mean of its two edges, for the 0.578 in the left side view reads)","method":"the face's two upright edges along the split, (466, 1594) and (1940, 1814): 1490 px. The bore stands 204 and 210 px inside them","via":"harvest"}}],"note":"No view is square across the mount. Read on the front ring's front face in a long-lens oblique, in that face's own plane, by the bore's chord along the split. The left side view's band for the same face (67 px against the bore's 45) would make it 1.76: a band 67 px wide can't tell."},"ring_split_above_axis":{"label":"Rings, the split between cap and lower half above the bore's centre","kind":"length","measurements":[{"id":"end","value":0.15,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount 424d97f623ad (Armamat 113267060_3.jpg, the mount alone from the front left and above, the front ring's front face toward the lens, 4200 x 2940)","scaleRef":"the front ring's front face in its own plane (a long lens: the background is out of focus): along the split between the cap and the lower half, 940 px/in by the 30 mm bore's chord there (1073.5 px from rim to rim; the split is 0.15 in above the bore's centre, so the chord is 1.142 in); up the face 801 px/in, by the lower half's side flat (463 px, the mean of its two edges, for the 0.578 in the left side view reads)","method":"the cap's bore is an arc that rises 354 px over a chord of 1073.5 px: a third of its chord, where a half ring's is a half. For a 30 mm circle that rise over that chord, with the face seen from 20 to 35 degrees above, puts the chord 0.14 to 0.20 in above the centre; the bore's top edge is 473 px (0.591 in up the face) above a centre 119 px under the split","via":"harvest"}},{"id":"left","value":0.13,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount edbba62833fd (Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334)","scaleRef":"the bore's opening on the front ring's rear face (rows 333 to 697: its centre at row 515, at the mid-plane) against the split on the near side flat (row 500), through the camera of ring_clearance's reading with the lens's height left to the base's own figures: with the lens above the picture (row -54) the cross bolts come out at the rail's top, where they must lie in its slots, and the split 0.13 in above the centre","method":"two heights at two depths in a photo taken from above: as good as the lens's height is","via":"harvest"}}],"adopt":{"from":"end","reason":"Read in one plane, the face's own, where the side view compares two depths from a lens whose height is itself inferred. They agree within either's ±."},"note":"The cap is less than a half ring: the lower half is a U whose walls stand straight up from the bore's centre to the split."},"ring_top_above_axis":{"label":"Rings, the cap's top above the bore's centre","kind":"length","measurements":[{"id":"left","value":0.645,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount edbba62833fd (Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334)","scaleRef":"a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm","method":"the front cap's top edge (row 320.8) and the bore's top edge on the same ring's rear face (row 333, 14 px lower), both at the mid-plane: the cap is 0.045 in thick over the tube, 0.062 by the top's own height through the camera; between the two. The rear ring's top reads 10 px higher in the picture than the front's (a roll of half a degree)","via":"harvest"}}]},"ring_ledge_height":{"label":"Ring caps, the ledge the screws stand on above the split","kind":"length","measurements":[{"id":"left","value":0.165,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount edbba62833fd (Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334)","scaleRef":"a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm","method":"the front cap's side flat, from the split (row 497 to 500) up to its upper edge (row 443, a lit line to 450: the ledge's top seen from above): 0.15 to 0.18 in at the near flats' scale. The rear cap's reads 0.115 in (rows 458 to 495), its lit line fainter","via":"harvest"}}]},"ring_flat_bottom_below_axis":{"label":"Rings, the side flat's lower end below the bore's centre","kind":"length","measurements":[{"id":"left","value":0.437,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount edbba62833fd (Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334)","scaleRef":"a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm","method":"the front ring's side flat ends at row 690, 0.578 in under the split at the near flats' scale, where a lit facet begins; less the split's height above the centre (ring_split_above_axis)","via":"harvest"}}]},"ring_facet_bottom_below_axis":{"label":"Rings, the foot of the facet under each side flat below the bore's centre","kind":"length","measurements":[{"id":"left","value":0.76,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount edbba62833fd (Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334)","scaleRef":"a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm","method":"the lit facet under the front ring's side flat, rows 690 to about 795 at column 250: 0.32 in of height at the near flats' scale; its lower edge is a change of tone, not a line","via":"harvest"}}],"note":"Under each side flat the ring narrows to the arm's width down a facet, lit in the left side view; on the front ring it runs on round the ring's front lower corner."},"ring_screw_head_d":{"label":"Ring cap screws, the head's diameter","kind":"length","measurements":[{"id":"left","value":0.24,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount edbba62833fd (Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334)","scaleRef":"a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm","method":"the front cap's two near heads, 76 px each at their widest (columns 160 to 236 and 262 to 338), at the scale of where they stand (318 px/in)","via":"harvest"}}]},"ring_screw_head_h":{"label":"Ring cap screws, the head's height above the ledge","kind":"length","measurements":[{"id":"left","value":0.11,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount edbba62833fd (Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334)","scaleRef":"a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm","method":"the same two heads, rows 407 to 443: socket heads, their upper third tapered, standing on the ledge with no counterbore","via":"harvest"}}]},"ring_screw_spacing":{"label":"Ring cap screws, the two on a side, centre to centre along the tube","kind":"length","measurements":[{"id":"left","value":0.315,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount edbba62833fd (Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334)","scaleRef":"a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm","method":"the two heads' middles on each cap: columns 198 and 300 on the front ring, 1232 and 1335 on the rear (102 and 103 px), about the flat's own middle","via":"harvest"}}]},"ring_screw_z":{"label":"Ring cap screws, their axes from the mount's mid-plane","kind":"length","measurements":[{"id":"end","value":0.67,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount 424d97f623ad (Armamat 113267060_3.jpg, the mount alone from the front left and above, the front ring's front face toward the lens, 4200 x 2940)","scaleRef":"the front ring's front face in its own plane (a long lens: the background is out of focus): along the split between the cap and the lower half, 940 px/in by the 30 mm bore's chord there (1073.5 px from rim to rim; the split is 0.15 in above the bore's centre, so the chord is 1.142 in); up the face 801 px/in, by the lower half's side flat (463 px, the mean of its two edges, for the 0.578 in the left side view reads)","method":"not read as a place: each head stands on its ledge between the cap's arch and the side flat, touching neither's edge in this view or in the rear oblique (1286e081602a); the ledge runs from 0.55 in (where an arch of the cap's own radius meets it) to the flat at 0.79, and the head is 0.24 across. Its middle","via":"harvest"}}]},"arm_width":{"label":"The arm under the rings, across","kind":"length","measurements":[{"id":"rear","value":1.2,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount 1286e081602a (Armamat 113267060_4.jpg, the mount alone from the rear right and above, the base's rear end toward the lens, 4200 x 2940)","scaleRef":"the base's rear end face in its own plane: the channel between the clamp bar and the fixed jaw, 314 px wide at its roof on a gridded crop (0.65 px to the pixel), taken to be the rail's top it clamps (std.picatinny.top_width, 0.835 in, and a hundredth of clearance): 374 px/in. An assumed fit, not a published size","method":"twice the fixed side's right face from the channel's middle (base_right_z): the arm is drawn about the mount's mid-plane, its right face one with the base's as the view from below has it","via":"harvest"}}],"note":"The arm and the base's fixed side are one width in the view from below (d4df1c9eae33): the rings stand out past it each side."},"base_right_z":{"label":"Base, its fixed (right) side's face from the mount's mid-plane","kind":"length","measurements":[{"id":"rear","value":0.6,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount 1286e081602a (Armamat 113267060_4.jpg, the mount alone from the rear right and above, the base's rear end toward the lens, 4200 x 2940)","scaleRef":"the base's rear end face in its own plane: the channel between the clamp bar and the fixed jaw, 314 px wide at its roof on a gridded crop (0.65 px to the pixel), taken to be the rail's top it clamps (std.picatinny.top_width, 0.835 in, and a hundredth of clearance): 374 px/in. An assumed fit, not a published size","method":"the fixed jaw is 68 px thick at the channel's roof (0.18 in), outside the rail's half width","via":"harvest"}}]},"clamp_bar_outer_z":{"label":"Clamp bar, its outer (left) face from the mount's mid-plane","kind":"length","measurements":[{"id":"rear","value":0.65,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount 1286e081602a (Armamat 113267060_4.jpg, the mount alone from the rear right and above, the base's rear end toward the lens, 4200 x 2940)","scaleRef":"the base's rear end face in its own plane: the channel between the clamp bar and the fixed jaw, 314 px wide at its roof on a gridded crop (0.65 px to the pixel), taken to be the rail's top it clamps (std.picatinny.top_width, 0.835 in, and a hundredth of clearance): 374 px/in. An assumed fit, not a published size","method":"the bar is 87 px thick at the channel's roof (0.23 in), outside the rail's half width; the whole clamp 472 px across its top (1.26 in)","via":"harvest"}}]},"clamp_bar_thickness":{"label":"Clamp bar, its thickness across the rifle","kind":"length","measurements":[{"id":"rear","value":0.23,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount 1286e081602a (Armamat 113267060_4.jpg, the mount alone from the rear right and above, the base's rear end toward the lens, 4200 x 2940)","scaleRef":"the base's rear end face in its own plane: the channel between the clamp bar and the fixed jaw, 314 px wide at its roof on a gridded crop (0.65 px to the pixel), taken to be the rail's top it clamps (std.picatinny.top_width, 0.835 in, and a hundredth of clearance): 374 px/in. An assumed fit, not a published size","method":"87 px at the channel's roof, from its inner face to its outer","via":"harvest"}}]},"base_right_break":{"label":"Base, the break on its top face's right edge","kind":"length","measurements":[{"id":"right","value":0.12,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount b0c1e411bf91 (Primary Arms PADLXSM_01.jpg, the mount alone on white, right side, 2000 x 1334)","scaleRef":"the rings' near side flats in this view, their inner ends 763.5 px apart for the 2.572 in the left view's camera reads (296.9 px/in), and the base's right face 0.19 in further from the lens (294 px/in); its two bolt heads are then 2.01 in apart (590 px) for five slots, 1.969","method":"the band under the top face's near edge, rows 915 to 950 at column 500, a shade darker than the top and lighter than the upright face under it: its height. How far in it reaches isn't read: drawn at 45 degrees","via":"harvest"}}],"note":"The right side view is taken from above as the left is: over this band the base's top face shows, lit, 55 px deep (rows 860 to 915), with the clamp bar's top beyond it."},"clamp_bolt_spacing":{"label":"Clamp cross bolts, centre to centre","kind":"length","measurements":[{"id":"slots","value":1.97,"unit":"in","source":{"type":"derived","expr":"5 * {std.picatinny.slot_pitch}","via":"harvest"}},{"id":"left","value":1.99,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount edbba62833fd (Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334)","scaleRef":"a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm","method":"the two studs' ends in their nuts, columns 1117 and 1770 (653 px), 1.12 in nearer the lens than the mid-plane (the bar's outer face and the washer and nut on it); the right side view's two bolt heads read 2.01 (590 px at 294 px/in)","via":"harvest"}}],"adopt":{"from":"slots","reason":"Both bolts lie in recoil slots, a whole number of pitches apart; the photos read 1.99 and 2.01, which is five and neither four nor six."},"note":"Each bolt crosses the channel as a bar in a rail slot (the view from below, d4df1c9eae33, has both): a whole number of slots apart."},"clamp_bolt_above_rail_top":{"label":"Clamp cross bolts, their axis above the rail's top","kind":"length","measurements":[{"id":"left","value":0,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount edbba62833fd (Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334)","scaleRef":"a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm","method":"the studs' ends, rows 1058 and 1063, through the camera with the rings' axis 1.5 in above the rail: -0.004 in. The right side view has the heads' middles 0.44 in under the base's top, -0.03 in","via":"harvest"}}]},"clamp_bolt_head_d":{"label":"Clamp cross bolts, the head's diameter","kind":"length","measurements":[{"id":"right","value":0.31,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount b0c1e411bf91 (Primary Arms PADLXSM_01.jpg, the mount alone on white, right side, 2000 x 1334)","scaleRef":"the rings' near side flats in this view, their inner ends 763.5 px apart for the 2.572 in the left view's camera reads (296.9 px/in), and the base's right face 0.19 in further from the lens (294 px/in); its two bolt heads are then 2.01 in apart (590 px) for five slots, 1.969","method":"each round head in the base's right face, 90 px across","via":"harvest"}}]},"clamp_bolt_head_h":{"label":"Clamp cross bolts, how far the head stands out of the base's right face","kind":"length","measurements":[{"id":"rear","value":0.03,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount 1286e081602a (Armamat 113267060_4.jpg, the mount alone from the rear right and above, the base's rear end toward the lens, 4200 x 2940)","scaleRef":"the base's rear end face in its own plane: the channel between the clamp bar and the fixed jaw, 314 px wide at its roof on a gridded crop (0.65 px to the pixel), taken to be the rail's top it clamps (std.picatinny.top_width, 0.835 in, and a hundredth of clearance): 374 px/in. An assumed fit, not a published size","method":"the rear head's knurled rim shows just proud of the face at the base's right rear corner: about 10 px","via":"harvest"}}]},"clamp_nut_af":{"label":"Clamp nuts, across flats","kind":"length","measurements":[{"id":"left","value":0.51,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount edbba62833fd (Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334)","scaleRef":"a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm","method":"the front nut's hexagon on the row through its middle, 170 px at the scale of where it stands (332 px/in). Slotted across its end (the reviewer: \"slotted hex nuts\", turned \"with a socket wrench, a broad-bladed screwdriver or simply the spare change in your pocket\")","via":"harvest"}}]},"clamp_nut_h":{"label":"Clamp nuts, the lock washer and nut out from the bar's face","kind":"length","measurements":[{"id":"rear","value":0.47,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount 1286e081602a (Armamat 113267060_4.jpg, the mount alone from the rear right and above, the base's rear end toward the lens, 4200 x 2940)","scaleRef":"the base's rear end face in its own plane: the channel between the clamp bar and the fixed jaw, 314 px wide at its roof on a gridded crop (0.65 px to the pixel), taken to be the rail's top it clamps (std.picatinny.top_width, 0.835 in, and a hundredth of clearance): 374 px/in. An assumed fit, not a published size","method":"the rear stud's washer and nut, 178 px out from the bar's outer face; nearer the lens than the face the scale is set on, so no shorter than this","via":"harvest"}}]},"base_behind_rear_bolt":{"label":"Base, its rear end behind the rear cross bolt","kind":"length","measurements":[{"id":"left","value":0.395,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount edbba62833fd (Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334)","scaleRef":"a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm","method":"the clamp bar's rear end, column 1881, at the bar's face's scale (319.5 px/in), behind the rear stud's end","via":"harvest"}}]},"mount_length":{"label":"Clamp length along the rail (at its foot)","kind":"length","measurements":[{"id":"left","value":2.77,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount edbba62833fd (Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334)","scaleRef":"a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm","method":"the clamp bar, end to end: columns 995 to 1881 at its face's scale. The fixed side's foot in the right side view is 2.84 (columns 172 to 1010 at 295 px/in); its front end slopes","via":"harvest"}}]},"base_top_above_rail":{"label":"Base, its top face above the rail's top","kind":"length","measurements":[{"id":"left","value":0.4,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount edbba62833fd (Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334)","scaleRef":"a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm","method":"the base's top near edge, row 890 at column 1600 (the dark face begins at row 912), through the camera at the top's own edge, 0.58 in out from the mid-plane: 0.396 in; 0.408 at the clamp bar's face. The near flats' frame reads the same edge 0.425. The arm's top between the rings (row 800) comes out 0.672 in over the rail the same way, and its underside 0.33","via":"harvest"}}],"note":"The traced outline is in the frame of the rings' near side flats and has the dark side face's upper edge: 0.07 in under the top (the break on its left edge, mid grey and outside the mask) and, in that frame, 0.03 in high, the base's side being further from a lens that stood above the picture. The model lowers the outline as one by that. With it the arm's top is 0.81 in under the rings' axis: Primary Arms' own SLx 1-6x24, sold in this mount, has its saddle's flat 0.793 under its axis, and SIG's TANGO-MSR 0.82."},"base_left_break":{"label":"Base, the break on its top face's left edge","kind":"length","measurements":[{"id":"left","value":0.07,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount edbba62833fd (Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334)","scaleRef":"a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm","method":"the mid-grey band along the top of the base's left side, rows 890 to 912 at column 1600: its height. The arm's top between the rings has the same band, rows 800 to 825 at column 600 (0.077 in). How far in it reaches isn't read: drawn at 45 degrees","via":"harvest"}}]},"base_rear_chamfer":{"label":"Base, the chamfer on its rear top corner (along the mount)","kind":"length","measurements":[{"id":"left","value":0.13,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount edbba62833fd (Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334)","scaleRef":"a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm","method":"the base's rear top corner is cut off from (1838, 857) to (1880, 912) in the left view and from (210, 860) to (172, 915) in the right: 42 and 38 px along the mount, about 0.17 in down. Its length along the mount","via":"harvest"}}]},"base_foot_front_x":{"label":"Base, the fixed side's foot: its front end ahead of the rear cross bolt","kind":"length","measurements":[{"id":"right","value":2.45,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount b0c1e411bf91 (Primary Arms PADLXSM_01.jpg, the mount alone on white, right side, 2000 x 1334)","scaleRef":"the rings' near side flats in this view, their inner ends 763.5 px apart for the 2.572 in the left view's camera reads (296.9 px/in), and the base's right face 0.19 in further from the lens (294 px/in); its two bolt heads are then 2.01 in apart (590 px) for five slots, 1.969","method":"the foot's front corner, column 1010, from the base's rear end at column 172 (838 px at 295 px/in, the base's right face's scale), less what the rear end is behind the bolt (base_behind_rear_bolt)","via":"harvest"}}],"note":"Ahead of it the fixed side slopes up to the arm's underside (the right side view: from its foot at column 1010 to the arm at column 1140)."},"base_slope_top_x":{"label":"Base, the fixed side's front slope: where it meets the arm's underside, ahead of the rear cross bolt","kind":"length","measurements":[{"id":"right","value":2.89,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount b0c1e411bf91 (Primary Arms PADLXSM_01.jpg, the mount alone on white, right side, 2000 x 1334)","scaleRef":"the rings' near side flats in this view, their inner ends 763.5 px apart for the 2.572 in the left view's camera reads (296.9 px/in), and the base's right face 0.19 in further from the lens (294 px/in); its two bolt heads are then 2.01 in apart (590 px) for five slots, 1.969","method":"the slope's upper end, column 1140 (as base_foot_front_x). The left side view has the body ahead of the clamp bar rising to the arm's underside in a hollow curve from 2.6 to 3.0 in, traced","via":"harvest"}}]},"clamp_bolt_bar_width":{"label":"Clamp cross bolts, the bar that crosses the channel: its width along the rail","kind":"length","measurements":[{"id":"slot","value":0.19,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{std.picatinny.slot_width} - 0.016in","via":"harvest"},"note":"The standard's slot less a clearance of 0.008 in each side: an assumed fit, not a reading."}],"note":"Each bolt crosses the channel as a flat-sided bar in a recoil slot (the view from below, d4df1c9eae33). Its own size isn't read: it is drawn a little under the slot it lies in."},"clamp_nut_slot_width":{"label":"Clamp nuts, the slot across the end: its width","kind":"length","measurements":[{"id":"rear","value":0.08,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount 1286e081602a (Armamat 113267060_4.jpg, the mount alone from the rear right and above, 4200 x 2940): the rear nut seen from its side, its slot a notch in its end","scaleRef":"the nut's own hexagon in the same view, three faces showing, 353 px from corner to corner for the 0.59 in its 0.51 in across flats makes (610 px/in, good to 5%); along the stud, the scale the stack was read at (clamp_nut_h: 575 px/in on the base's rear end)","method":"the notch between its two lips, 49 px (rows 2355 to 2404 at column 1085). End on in the left side view (edbba62833fd) the same slot is a gap of about 25 px in the front nut's rim, 0.075 in","via":"harvest"}}]},"clamp_nut_slot_depth":{"label":"Clamp nuts, the slot across the end: its depth","kind":"length","measurements":[{"id":"rear","value":0.1,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount 1286e081602a (Armamat 113267060_4.jpg, the mount alone from the rear right and above, 4200 x 2940): the rear nut seen from its side, its slot a notch in its end","scaleRef":"the nut's own hexagon in the same view, three faces showing, 353 px from corner to corner for the 0.59 in its 0.51 in across flats makes (610 px/in, good to 5%); along the stud, the scale the stack was read at (clamp_nut_h: 575 px/in on the base's rear end)","method":"the notch from the nut's end to its floor, 59 px along the stud (columns 1055 to 1115): 0.097 to 0.103 in by the two scales","via":"harvest"}}]},"clamp_nut_collar_h":{"label":"Clamp nuts, the round collar between the hexagon and the lock washer: its length","kind":"length","measurements":[{"id":"obliques","value":0.19,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount 1286e081602a (Armamat 113267060_4.jpg, from the rear right and above) and d4df1c9eae33 (Armamat 113267060_5.jpg, from below and behind): the rear nut from its side in each","scaleRef":"the stack's own length out from the bar's face (clamp_nut_h, 0.47 in): what share of it is round","method":"111 px of the stack's 286 in the first (the hexagon begins at column 1232), 125 of 315 in the second (rows 1525 to 1650 of 1525 to 1840): 39 and 40% of the stack","via":"harvest"}}],"note":"Each nut is a hexagon with a round collar toward the clamp bar, a groove round the collar, and a split lock washer between it and the bar (the reviewer: \"Lock washers keep the nuts from loosening up during use\"). The washer and the groove aren't drawn apart: the collar is drawn to the bar's face."},"clamp_nut_collar_d":{"label":"Clamp nuts, the round collar's diameter","kind":"length","measurements":[{"id":"obliques","value":0.44,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount d4df1c9eae33 (Armamat 113267060_5.jpg, from below and behind) and 1286e081602a (Armamat 113267060_4.jpg, from the rear right and above)","scaleRef":"the nut's own hexagon in each view, corner to corner (0.59 in for 0.51 across flats)","method":"275 px across the collar for 350 across the hexagon's corners in the view from below (0.46 in); 255 px for 353 in the rear oblique (0.42 in). Between the two","via":"harvest"}}]},"clamp_nut_recess_d":{"label":"Clamp nuts, the round recess in the end round the stud: its diameter","kind":"length","measurements":[{"id":"left","value":0.33,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount edbba62833fd (Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334)","scaleRef":"a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm","method":"the front nut end on: the dark recess round the stud's end, columns 1070 to 1180 on the row through its middle, at the scale of where the nut's end stands (332 px/in)","via":"harvest"}}]},"clamp_stud_d":{"label":"Clamp cross bolts, the stud's end in the nut: its diameter","kind":"length","measurements":[{"id":"left","value":0.145,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount edbba62833fd (Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334)","scaleRef":"a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm","method":"the front stud's end, a paler disc in the nut's recess, columns 1100 to 1148 (332 px/in)","via":"harvest"}}]},"base_rear_chamfer_drop":{"label":"Base, the chamfer on its rear top corner (down the rear end)","kind":"length","measurements":[{"id":"sides","value":0.17,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/primary-arms-deluxe-30mm-mount edbba62833fd (Primary Arms PADLXSM_00.jpg, left side) and b0c1e411bf91 (PADLXSM_01.jpg, right side)","scaleRef":"each view's scale at the base's own side (319.5 and 294 px/in)","method":"the cut corner runs 55 rows down in each view (857 to 912 on the left, 860 to 915 on the right): 0.17 and 0.19 in. With base_rear_chamfer it leans 53 degrees from level","via":"harvest"}}]},"ring_split_groove_width":{"label":"Rings, the line between cap and lower half as drawn: the groove's width","kind":"length","measurements":[{"id":"assumed","value":0.008,"unit":"in","pm":0.004,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the photos have a dark line between each cap and its lower half, a pixel or two wide, and no view shows a gap in profile. It was a number in the script until the first review, 2026-10-13.","via":"harvest"}}]},"ring_split_groove_depth":{"label":"Rings, the line between cap and lower half as drawn: the groove's depth","kind":"length","measurements":[{"id":"assumed","value":0.012,"unit":"in","pm":0.006,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows it in profile. It was a number in the script until the first review, 2026-10-13.","via":"harvest"}}]},"clamp_bar_seam_groove":{"label":"Clamp bar, the line between it and the base's shoulder as drawn: the groove's width and depth","kind":"length","measurements":[{"id":"assumed","value":0.012,"unit":"in","pm":0.006,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the left side view has a line along the bar's top, and no view on file shows it in profile. It was a number in the script until the first review, 2026-10-13.","via":"harvest"}}]},"clamp_nut_recess_depth":{"label":"Clamp nuts, the round recess in the end round the stud: its depth","kind":"length","measurements":[{"id":"assumed","value":0.07,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the recess is seen end on only, and no view on file shows it in profile. It was a number in the script until the first review, 2026-10-13.","via":"harvest"}}]},"clamp_stud_end_below_nut_end":{"label":"Clamp cross bolts, the stud's end under the nut's end face","kind":"length","measurements":[{"id":"assumed","value":0.06,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the stud's end shows inside the nut's recess end on, a little off its floor, and no view on file shows it in profile. It was a number in the script until the first review, 2026-10-13.","via":"harvest"}}]}}},{"subject":"primary-arms-slx-1-6x24-gen-iv","title":"Primary Arms SLx 1-6x24mm SFP Rifle Scope Gen IV - Illuminated ACSS Nova Fiber Wire Reticle - Red Dot Bright®","dimensions":{"length":{"label":"Overall length (the objective's front face to the eyepiece's rear face)","kind":"length","measurements":[{"id":"page","value":10.4,"unit":"in","stated":"Length w/o Lens Covers: 10.4 in.","source":{"type":"spec","publisher":"manufacturer","name":"Primary Arms, SLx 1-6x24mm SFP Rifle Scope Gen IV - Illuminated ACSS Nova Fiber Wire Reticle - Red Dot Bright® (SKU: PA-SLX-1-6X24S-NOVA), product page","url":"https://www.primaryarms.com/primary-arms-slx-1-6x24mm-sfp-rifle-scope-gen-4-illuminated-acss-nova-fiber-wire-reticle","retrieved":"2026-10-13","via":"harvest"}},{"id":"manual","value":10.4,"unit":"in","stated":"Length (w/o Lens Covers): 10.4 in","source":{"type":"spec","publisher":"manufacturer","name":"Primary Arms, SLx 1-6x24 Second Focal Plane Optic Manual (the product page's \"PA-SLX-1-6X24S-NOVA MANUAL 1\"), its specifications page (the sheet numbered 8)","url":"https://www.primaryarms.com/core/media/media.nl?id=27324763&c=3901023&h=RGxrJcgqL1VeTNeJeGdY5vFk5fuJdHW2xS5NUJj_RUtz0sSM","retrieved":"2026-10-13","via":"harvest"}},{"id":"trex","value":10.4,"unit":"in","stated":"Length 10.4 in.","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, Primary Arms SLx 1-6x24 SFP Rifle Scope Gen IV (Quick Specifications)","url":"https://www.trex-arms.com/store/primary-arms-slx-1-6x24-sfp-rifle-scope-gen-iv","retrieved":"2026-10-13","via":"harvest"}}],"adopt":{"from":"page","reason":"The maker's page for this product; its manual and a seller say the same."},"note":"Without the lens covers it ships with (\"Scope caps included\"), which aren't drawn."},"tube_od":{"label":"Main tube diameter","kind":"length","measurements":[{"id":"manual","value":30,"unit":"mm","stated":"Tube Diameter: 30 mm","source":{"type":"spec","publisher":"manufacturer","name":"Primary Arms, SLx 1-6x24 Second Focal Plane Optic Manual (the product page's \"PA-SLX-1-6X24S-NOVA MANUAL 1\"), its specifications page (the sheet numbered 8)","url":"https://www.primaryarms.com/core/media/media.nl?id=27324763&c=3901023&h=RGxrJcgqL1VeTNeJeGdY5vFk5fuJdHW2xS5NUJj_RUtz0sSM","retrieved":"2026-10-13","via":"harvest"}},{"id":"page","value":30,"unit":"mm","stated":"Mount Compatibility 30mm","source":{"type":"spec","publisher":"manufacturer","name":"Primary Arms, SLx 1-6x24mm SFP Rifle Scope Gen IV - Illuminated ACSS Nova Fiber Wire Reticle - Red Dot Bright® (SKU: PA-SLX-1-6X24S-NOVA), product page","url":"https://www.primaryarms.com/primary-arms-slx-1-6x24mm-sfp-rifle-scope-gen-4-illuminated-acss-nova-fiber-wire-reticle","retrieved":"2026-10-13","via":"harvest"},"note":"The page's table has no row for the tube: this is what it says a mount has to be."},{"id":"trex","value":30,"unit":"mm","stated":"High-strength 30mm main tube","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, Primary Arms SLx 1-6x24 SFP Rifle Scope Gen IV (Quick Specifications)","url":"https://www.trex-arms.com/store/primary-arms-slx-1-6x24-sfp-rifle-scope-gen-iv","retrieved":"2026-10-13","via":"harvest"}}],"adopt":{"from":"manual","reason":"The manual names the tube's diameter; the page's mount row and a seller's sentence say the same 30 mm."}},"objective_lens_d":{"label":"Objective lens diameter","kind":"length","measurements":[{"id":"manual","value":24,"unit":"mm","stated":"Objective Lens Diameter: 24 mm","source":{"type":"spec","publisher":"manufacturer","name":"Primary Arms, SLx 1-6x24 Second Focal Plane Optic Manual (the product page's \"PA-SLX-1-6X24S-NOVA MANUAL 1\"), its specifications page (the sheet numbered 8)","url":"https://www.primaryarms.com/core/media/media.nl?id=27324763&c=3901023&h=RGxrJcgqL1VeTNeJeGdY5vFk5fuJdHW2xS5NUJj_RUtz0sSM","retrieved":"2026-10-13","via":"harvest"}},{"id":"page","value":24,"unit":"mm","stated":"Objective Lens Diameter: 24mm","source":{"type":"spec","publisher":"manufacturer","name":"Primary Arms, SLx 1-6x24mm SFP Rifle Scope Gen IV - Illuminated ACSS Nova Fiber Wire Reticle - Red Dot Bright® (SKU: PA-SLX-1-6X24S-NOVA), product page","url":"https://www.primaryarms.com/primary-arms-slx-1-6x24mm-sfp-rifle-scope-gen-4-illuminated-acss-nova-fiber-wire-reticle","retrieved":"2026-10-13","via":"harvest"}}],"adopt":{"from":"manual","reason":"The maker's manual and its page agree."}},"weight":{"label":"Weight (the scope alone, without rings or a mount)","kind":"mass","measurements":[{"id":"manual","value":17.85,"unit":"oz","stated":"Weight (with Battery, without Lens Covers): 17.85 oz","source":{"type":"spec","publisher":"manufacturer","name":"Primary Arms, SLx 1-6x24 Second Focal Plane Optic Manual (the product page's \"PA-SLX-1-6X24S-NOVA MANUAL 1\"), its specifications page (the sheet numbered 8)","url":"https://www.primaryarms.com/core/media/media.nl?id=27324763&c=3901023&h=RGxrJcgqL1VeTNeJeGdY5vFk5fuJdHW2xS5NUJj_RUtz0sSM","retrieved":"2026-10-13","via":"harvest"}},{"id":"page","value":17.9,"unit":"oz","stated":"Weight w/ Included Battery w/o Lens Covers: 17.9 oz.","source":{"type":"spec","publisher":"manufacturer","name":"Primary Arms, SLx 1-6x24mm SFP Rifle Scope Gen IV - Illuminated ACSS Nova Fiber Wire Reticle - Red Dot Bright® (SKU: PA-SLX-1-6X24S-NOVA), product page","url":"https://www.primaryarms.com/primary-arms-slx-1-6x24mm-sfp-rifle-scope-gen-4-illuminated-acss-nova-fiber-wire-reticle","retrieved":"2026-10-13","via":"harvest"}},{"id":"trex","value":17.9,"unit":"oz","stated":"Weight 17.9 oz.","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, Primary Arms SLx 1-6x24 SFP Rifle Scope Gen IV (Quick Specifications)","url":"https://www.trex-arms.com/store/primary-arms-slx-1-6x24-sfp-rifle-scope-gen-iv","retrieved":"2026-10-13","via":"harvest"}}],"adopt":{"from":"manual","reason":"The maker's two figures are one weight: the manual's to a hundredth, the page's the same rounded to a tenth (a seller repeats the page's)."},"note":"The scope with its battery and without its lens covers, by both of the maker's figures; no mount comes with it. Neither says whether the throw lever is on: every studio picture has it fitted, and the page lists it as a feature (\"Integrated Magnification Throw Lever\")."},"eye_relief":{"label":"Eye relief","kind":"length","measurements":[{"id":"page","value":4,"unit":"in","pm":0.005,"stated":"Eye Relief 4.00 in","source":{"type":"spec","publisher":"manufacturer","name":"Primary Arms, SLx 1-6x24mm SFP Rifle Scope Gen IV - Illuminated ACSS Nova Fiber Wire Reticle - Red Dot Bright® (SKU: PA-SLX-1-6X24S-NOVA), product page","url":"https://www.primaryarms.com/primary-arms-slx-1-6x24mm-sfp-rifle-scope-gen-4-illuminated-acss-nova-fiber-wire-reticle","retrieved":"2026-10-13","via":"harvest"}},{"id":"manual","value":4,"unit":"in","stated":"Eye Relief: 4 in","source":{"type":"spec","publisher":"manufacturer","name":"Primary Arms, SLx 1-6x24 Second Focal Plane Optic Manual (the product page's \"PA-SLX-1-6X24S-NOVA MANUAL 1\"), its specifications page (the sheet numbered 8)","url":"https://www.primaryarms.com/core/media/media.nl?id=27324763&c=3901023&h=RGxrJcgqL1VeTNeJeGdY5vFk5fuJdHW2xS5NUJj_RUtz0sSM","retrieved":"2026-10-13","via":"harvest"}}],"adopt":{"from":"page","reason":"The page's table states it to a hundredth; the manual's whole number is the same."},"note":"One figure for the whole range of magnification: the maker gives none for 1x and 6x apart."},"tube_rear_from":{"label":"Main tube behind the saddle, where it begins (ahead of the magnification ring)","kind":"length","measurements":[{"id":"right","value":3.23,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv d9806411659f (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_03.jpg (the Aurora 5.56 yard sibling: the same body), right side: the turned body)","scaleRef":"scale from primary-arms-slx-1-6x24-gen-iv.tube_od = 1.1811 in, the tube's own width column by column: 216.7 px over columns 760–980, 216.8 px over columns 990–1210, 216.4 px over columns 1505–1760, 215.5 px over columns 1770–2035; a line through them (rms 0.27 px) changes -0.6% from column 760 to 2035, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 183.4 px/in there. The axis is the tube's centre line (tilt -0.19°, rms 0.08 px). Lengths then scaled by 1.0140 so that the end faces are primary-arms-slx-1-6x24-gen-iv.length = 10.4 in apart: at the tube's scale they read 10.256 (-1.4%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.106 in over radius 0.588 (rms 0.001), the rear end's rim sags 0.190 in over radius 0.855 (rms 0.002)","method":"x_max in x [2.6, 4.5] in y [0.6026, 2.0] of the traced outline (tools/trace.py); where the outline's reach above the axis comes down to within 0.012 in of the tube's radius ahead of the magnification ring","via":"harvest"}},{"id":"left","value":3.246,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv 3ff18059ddc4 (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_04.jpg (the Aurora 5.56 yard sibling: the same body), left side: the turned body)","scaleRef":"scale from primary-arms-slx-1-6x24-gen-iv.tube_od = 1.1811 in, the tube's own width column by column: 221.6 px over columns 140–410, 222.6 px over columns 420–690, 223.2 px over columns 980–1210, 223.1 px over columns 1220–1455; a line through them (rms 0.28 px) changes +0.8% from column 140 to 1455, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 188.8 px/in there. The axis is the tube's centre line (tilt +0.26°, rms 0.06 px). Lengths then scaled by 1.0145 so that the end faces are primary-arms-slx-1-6x24-gen-iv.length = 10.4 in apart: at the tube's scale they read 10.251 (-1.4%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.137 in over radius 0.589 (rms 0.002), the rear end's rim sags 0.147 in over radius 0.851 (rms 0.002)","method":"x_max in x [2.6, 4.5] in y [0.6026, 2.0] of the traced outline (tools/trace.py); where the outline's reach above the axis comes down to within 0.012 in of the tube's radius ahead of the magnification ring (the left side, mirrored)","via":"harvest"}}],"adopt":{"from":"right","reason":"The right side is the photo the outlines are traced from; the left side, mirrored and traced on its own, agrees within its ±."},"note":"Behind it the body widens in a cone to the magnification ring: a ring can't be clamped there. Both side views, each by its own trace."},"tube_rear_to":{"label":"Main tube behind the saddle, where it ends at the saddle","kind":"length","measurements":[{"id":"right","value":5.861,"unit":"in","pm":0.021,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv d9806411659f (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_03.jpg (the Aurora 5.56 yard sibling: the same body), right side: the turned body)","scaleRef":"scale from primary-arms-slx-1-6x24-gen-iv.tube_od = 1.1811 in, the tube's own width column by column: 216.7 px over columns 760–980, 216.8 px over columns 990–1210, 216.4 px over columns 1505–1760, 215.5 px over columns 1770–2035; a line through them (rms 0.27 px) changes -0.6% from column 760 to 2035, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 183.4 px/in there. The axis is the tube's centre line (tilt -0.19°, rms 0.08 px). Lengths then scaled by 1.0140 so that the end faces are primary-arms-slx-1-6x24-gen-iv.length = 10.4 in apart: at the tube's scale they read 10.256 (-1.4%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.106 in over radius 0.588 (rms 0.001), the rear end's rim sags 0.190 in over radius 0.855 (rms 0.002)","method":"x_min in x [4.5, 6.6] in y [0.6026, 2.0] of the traced outline (tools/trace.py); where the outline leaves the tube's radius (by 0.012 in) going up onto the saddle","via":"harvest"}},{"id":"left","value":5.875,"unit":"in","pm":0.021,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv 3ff18059ddc4 (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_04.jpg (the Aurora 5.56 yard sibling: the same body), left side: the turned body)","scaleRef":"scale from primary-arms-slx-1-6x24-gen-iv.tube_od = 1.1811 in, the tube's own width column by column: 221.6 px over columns 140–410, 222.6 px over columns 420–690, 223.2 px over columns 980–1210, 223.1 px over columns 1220–1455; a line through them (rms 0.28 px) changes +0.8% from column 140 to 1455, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 188.8 px/in there. The axis is the tube's centre line (tilt +0.26°, rms 0.06 px). Lengths then scaled by 1.0145 so that the end faces are primary-arms-slx-1-6x24-gen-iv.length = 10.4 in apart: at the tube's scale they read 10.251 (-1.4%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.137 in over radius 0.589 (rms 0.002), the rear end's rim sags 0.147 in over radius 0.851 (rms 0.002)","method":"x_min in x [4.5, 6.6] in y [0.6026, 2.0] of the traced outline (tools/trace.py); where the outline leaves the tube's radius (by 0.012 in) going up onto the saddle (the left side, mirrored)","via":"harvest"}}],"adopt":{"from":"right","reason":"The right side is the photo the outlines are traced from; the left side, mirrored and traced on its own, agrees within its ±."},"note":"Where the saddle's rear shoulder begins. The ball the saddle is drawn as (saddle_radius) meets the tube here by construction."},"tube_front_from":{"label":"Main tube ahead of the saddle, where it begins at the saddle","kind":"length","measurements":[{"id":"right","value":7.341,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv d9806411659f (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_03.jpg (the Aurora 5.56 yard sibling: the same body), right side: the turned body)","scaleRef":"scale from primary-arms-slx-1-6x24-gen-iv.tube_od = 1.1811 in, the tube's own width column by column: 216.7 px over columns 760–980, 216.8 px over columns 990–1210, 216.4 px over columns 1505–1760, 215.5 px over columns 1770–2035; a line through them (rms 0.27 px) changes -0.6% from column 760 to 2035, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 183.4 px/in there. The axis is the tube's centre line (tilt -0.19°, rms 0.08 px). Lengths then scaled by 1.0140 so that the end faces are primary-arms-slx-1-6x24-gen-iv.length = 10.4 in apart: at the tube's scale they read 10.256 (-1.4%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.106 in over radius 0.588 (rms 0.001), the rear end's rim sags 0.190 in over radius 0.855 (rms 0.002)","method":"x_max in x [6.6, 8.5] in y [0.6026, 2.0] of the traced outline (tools/trace.py); where the outline comes down off the saddle to within 0.012 in of the tube's radius","via":"harvest"}},{"id":"left","value":7.357,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv 3ff18059ddc4 (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_04.jpg (the Aurora 5.56 yard sibling: the same body), left side: the turned body)","scaleRef":"scale from primary-arms-slx-1-6x24-gen-iv.tube_od = 1.1811 in, the tube's own width column by column: 221.6 px over columns 140–410, 222.6 px over columns 420–690, 223.2 px over columns 980–1210, 223.1 px over columns 1220–1455; a line through them (rms 0.28 px) changes +0.8% from column 140 to 1455, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 188.8 px/in there. The axis is the tube's centre line (tilt +0.26°, rms 0.06 px). Lengths then scaled by 1.0145 so that the end faces are primary-arms-slx-1-6x24-gen-iv.length = 10.4 in apart: at the tube's scale they read 10.251 (-1.4%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.137 in over radius 0.589 (rms 0.002), the rear end's rim sags 0.147 in over radius 0.851 (rms 0.002)","method":"x_max in x [6.6, 8.5] in y [0.6026, 2.0] of the traced outline (tools/trace.py); where the outline comes down off the saddle to within 0.012 in of the tube's radius (the left side, mirrored)","via":"harvest"}}],"adopt":{"from":"right","reason":"The right side is the photo the outlines are traced from; the left side, mirrored and traced on its own, agrees within its ±."},"note":"Where the saddle's front shoulder ends: the saddle is 1.48 in long, which is what has to go between a mount's two rings."},"tube_front_to":{"label":"Main tube ahead of the saddle, where it ends (the front face of a straight tube)","kind":"length","measurements":[{"id":"right","value":10.413,"unit":"in","pm":0.035,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv d9806411659f (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_03.jpg (the Aurora 5.56 yard sibling: the same body), right side: the turned body)","scaleRef":"scale from primary-arms-slx-1-6x24-gen-iv.tube_od = 1.1811 in, the tube's own width column by column: 216.7 px over columns 760–980, 216.8 px over columns 990–1210, 216.4 px over columns 1505–1760, 215.5 px over columns 1770–2035; a line through them (rms 0.27 px) changes -0.6% from column 760 to 2035, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 183.4 px/in there. The axis is the tube's centre line (tilt -0.19°, rms 0.08 px). Lengths then scaled by 1.0140 so that the end faces are primary-arms-slx-1-6x24-gen-iv.length = 10.4 in apart: at the tube's scale they read 10.256 (-1.4%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.106 in over radius 0.588 (rms 0.001), the rear end's rim sags 0.190 in over radius 0.855 (rms 0.002)","method":"x_max in x [9.0, 11.0] in y [0.5786, 0.62] of the traced outline (tools/trace.py); the last of the outline at the tube's radius (within 0.012 in), at the front rim: a straight tube to the objective's face","via":"harvest"}},{"id":"left","value":10.422,"unit":"in","pm":0.035,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv 3ff18059ddc4 (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_04.jpg (the Aurora 5.56 yard sibling: the same body), left side: the turned body)","scaleRef":"scale from primary-arms-slx-1-6x24-gen-iv.tube_od = 1.1811 in, the tube's own width column by column: 221.6 px over columns 140–410, 222.6 px over columns 420–690, 223.2 px over columns 980–1210, 223.1 px over columns 1220–1455; a line through them (rms 0.28 px) changes +0.8% from column 140 to 1455, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 188.8 px/in there. The axis is the tube's centre line (tilt +0.26°, rms 0.06 px). Lengths then scaled by 1.0145 so that the end faces are primary-arms-slx-1-6x24-gen-iv.length = 10.4 in apart: at the tube's scale they read 10.251 (-1.4%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.137 in over radius 0.589 (rms 0.002), the rear end's rim sags 0.147 in over radius 0.851 (rms 0.002)","method":"x_max in x [9.0, 11.0] in y [0.5786, 0.62] of the traced outline (tools/trace.py); the last of the outline at the tube's radius (within 0.012 in), at the front rim (the left side, mirrored)","via":"harvest"}}],"adopt":{"from":"right","reason":"The right side is the photo the outlines are traced from; the left side, mirrored and traced on its own, agrees within its ±."},"note":"A straight tube to the objective's front face, with no bell: nothing but the end of the scope stops a ring here. The reading is the outline's last point at the tube's radius, 0.012 in past the face itself (objective_front_x, 10.401), inside both readings' ±."},"eyepiece_rear_x":{"label":"eyepiece rear x","kind":"length","measurements":[{"id":"right","value":0.001,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv d9806411659f (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_03.jpg (the Aurora 5.56 yard sibling: the same body), right side, 2200 x 1467)","scaleRef":"scale from primary-arms-slx-1-6x24-gen-iv.tube_od = 1.1811 in, the tube's own width column by column: 216.7 px over columns 760–980, 216.8 px over columns 990–1210, 216.4 px over columns 1505–1760, 215.5 px over columns 1770–2035; a line through them (rms 0.27 px) changes -0.6% from column 760 to 2035, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 183.4 px/in there. The axis is the tube's centre line (tilt -0.19°, rms 0.08 px). Lengths then scaled by 1.0140 so that the end faces are primary-arms-slx-1-6x24-gen-iv.length = 10.4 in apart: at the tube's scale they read 10.256 (-1.4%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.106 in over radius 0.588 (rms 0.001), the rear end's rim sags 0.190 in over radius 0.855 (rms 0.002)","method":"the min end's face: the silhouette's tip at -0.192 less its rim's arc, 0.193 in of sag at radius 0.855353 (the end is seen from 12.7° off square; arc fitted over 121 rows, rms 0.002) of the traced outline (tools/trace.py); the eyepiece's rear face, behind its rim's arc","via":"harvest"}},{"id":"left","value":0,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv 3ff18059ddc4 (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_04.jpg (the Aurora 5.56 yard sibling: the same body), left side, 2200 x 1467)","scaleRef":"scale from primary-arms-slx-1-6x24-gen-iv.tube_od = 1.1811 in, the tube's own width column by column: 221.6 px over columns 140–410, 222.6 px over columns 420–690, 223.2 px over columns 980–1210, 223.1 px over columns 1220–1455; a line through them (rms 0.28 px) changes +0.8% from column 140 to 1455, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 188.8 px/in there. The axis is the tube's centre line (tilt +0.26°, rms 0.06 px). Lengths then scaled by 1.0145 so that the end faces are primary-arms-slx-1-6x24-gen-iv.length = 10.4 in apart: at the tube's scale they read 10.251 (-1.4%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.137 in over radius 0.589 (rms 0.002), the rear end's rim sags 0.147 in over radius 0.851 (rms 0.002)","method":"the min end's face: the silhouette's tip at -0.149 less its rim's arc, 0.149 in of sag at radius 0.85063 (the end is seen from 9.9° off square; arc fitted over 118 rows, rms 0.002) of the traced outline (tools/trace.py); the eyepiece's rear face, behind its rim's arc (the left side, mirrored)","via":"harvest"}}],"adopt":{"from":"right","reason":"The right side is the photo the outlines are traced from; the left side, mirrored and traced on its own, agrees within its ±."}},"objective_front_x":{"label":"objective front x","kind":"length","measurements":[{"id":"right","value":10.401,"unit":"in","pm":0.035,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv d9806411659f (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_03.jpg (the Aurora 5.56 yard sibling: the same body), right side, 2200 x 1467)","scaleRef":"scale from primary-arms-slx-1-6x24-gen-iv.tube_od = 1.1811 in, the tube's own width column by column: 216.7 px over columns 760–980, 216.8 px over columns 990–1210, 216.4 px over columns 1505–1760, 215.5 px over columns 1770–2035; a line through them (rms 0.27 px) changes -0.6% from column 760 to 2035, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 183.4 px/in there. The axis is the tube's centre line (tilt -0.19°, rms 0.08 px). Lengths then scaled by 1.0140 so that the end faces are primary-arms-slx-1-6x24-gen-iv.length = 10.4 in apart: at the tube's scale they read 10.256 (-1.4%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.106 in over radius 0.588 (rms 0.001), the rear end's rim sags 0.190 in over radius 0.855 (rms 0.002)","method":"the max end's face: the silhouette's tip at 10.509 less its rim's arc, 0.108 in of sag at radius 0.588022 (the end is seen from 10.4° off square; arc fitted over 121 rows, rms 0.001) of the traced outline (tools/trace.py); the objective's front face, behind its rim's arc","via":"harvest"}},{"id":"left","value":10.4,"unit":"in","pm":0.035,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv 3ff18059ddc4 (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_04.jpg (the Aurora 5.56 yard sibling: the same body), left side, 2200 x 1467)","scaleRef":"scale from primary-arms-slx-1-6x24-gen-iv.tube_od = 1.1811 in, the tube's own width column by column: 221.6 px over columns 140–410, 222.6 px over columns 420–690, 223.2 px over columns 980–1210, 223.1 px over columns 1220–1455; a line through them (rms 0.28 px) changes +0.8% from column 140 to 1455, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 188.8 px/in there. The axis is the tube's centre line (tilt +0.26°, rms 0.06 px). Lengths then scaled by 1.0145 so that the end faces are primary-arms-slx-1-6x24-gen-iv.length = 10.4 in apart: at the tube's scale they read 10.251 (-1.4%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.137 in over radius 0.589 (rms 0.002), the rear end's rim sags 0.147 in over radius 0.851 (rms 0.002)","method":"the max end's face: the silhouette's tip at 10.540 less its rim's arc, 0.139 in of sag at radius 0.589387 (the end is seen from 13.3° off square; arc fitted over 121 rows, rms 0.002) of the traced outline (tools/trace.py); the objective's front face, behind its rim's arc (the left side, mirrored)","via":"harvest"}}],"adopt":{"from":"right","reason":"The right side is the photo the outlines are traced from; the left side, mirrored and traced on its own, agrees within its ±."}},"elevation_top_above_axis":{"label":"elevation top above axis","kind":"length","measurements":[{"id":"right","value":1.232,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv d9806411659f (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_03.jpg (the Aurora 5.56 yard sibling: the same body), right side, 2200 x 1467)","scaleRef":"scale from primary-arms-slx-1-6x24-gen-iv.tube_od = 1.1811 in, the tube's own width column by column: 216.7 px over columns 760–980, 216.8 px over columns 990–1210, 216.4 px over columns 1505–1760, 215.5 px over columns 1770–2035; a line through them (rms 0.27 px) changes -0.6% from column 760 to 2035, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 183.4 px/in there. The axis is the tube's centre line (tilt -0.19°, rms 0.08 px). Lengths then scaled by 1.0140 so that the end faces are primary-arms-slx-1-6x24-gen-iv.length = 10.4 in apart: at the tube's scale they read 10.256 (-1.4%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.106 in over radius 0.588 (rms 0.001), the rear end's rim sags 0.190 in over radius 0.855 (rms 0.002)","method":"y_max in x [5.8, 7.5] of the traced outline (tools/trace.py); the elevation turret's highest point above the tube's axis","via":"harvest"}},{"id":"left","value":1.242,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv 3ff18059ddc4 (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_04.jpg (the Aurora 5.56 yard sibling: the same body), left side, 2200 x 1467)","scaleRef":"scale from primary-arms-slx-1-6x24-gen-iv.tube_od = 1.1811 in, the tube's own width column by column: 221.6 px over columns 140–410, 222.6 px over columns 420–690, 223.2 px over columns 980–1210, 223.1 px over columns 1220–1455; a line through them (rms 0.28 px) changes +0.8% from column 140 to 1455, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 188.8 px/in there. The axis is the tube's centre line (tilt +0.26°, rms 0.06 px). Lengths then scaled by 1.0145 so that the end faces are primary-arms-slx-1-6x24-gen-iv.length = 10.4 in apart: at the tube's scale they read 10.251 (-1.4%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.137 in over radius 0.589 (rms 0.002), the rear end's rim sags 0.147 in over radius 0.851 (rms 0.002)","method":"y_max in x [5.8, 7.5] of the traced outline (tools/trace.py); the elevation turret's highest point above the tube's axis (the left side, mirrored)","via":"harvest"}}],"adopt":{"from":"right","reason":"The right side is the photo the outlines are traced from; the left side, mirrored and traced on its own, agrees within its ±."}},"lever_tip_above_axis":{"label":"lever tip above axis","kind":"length","measurements":[{"id":"right","value":1.611,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv d9806411659f (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_03.jpg (the Aurora 5.56 yard sibling: the same body), right side, 2200 x 1467)","scaleRef":"scale from primary-arms-slx-1-6x24-gen-iv.tube_od = 1.1811 in, the tube's own width column by column: 216.7 px over columns 760–980, 216.8 px over columns 990–1210, 216.4 px over columns 1505–1760, 215.5 px over columns 1770–2035; a line through them (rms 0.27 px) changes -0.6% from column 760 to 2035, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 183.4 px/in there. The axis is the tube's centre line (tilt -0.19°, rms 0.08 px). Lengths then scaled by 1.0140 so that the end faces are primary-arms-slx-1-6x24-gen-iv.length = 10.4 in apart: at the tube's scale they read 10.256 (-1.4%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.106 in over radius 0.588 (rms 0.001), the rear end's rim sags 0.190 in over radius 0.855 (rms 0.002)","method":"y_max in x [2.0, 3.3] of the traced outline (tools/trace.py); the throw lever's tip above the tube's axis","via":"harvest"}},{"id":"left","value":1.609,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv 3ff18059ddc4 (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_04.jpg (the Aurora 5.56 yard sibling: the same body), left side, 2200 x 1467)","scaleRef":"scale from primary-arms-slx-1-6x24-gen-iv.tube_od = 1.1811 in, the tube's own width column by column: 221.6 px over columns 140–410, 222.6 px over columns 420–690, 223.2 px over columns 980–1210, 223.1 px over columns 1220–1455; a line through them (rms 0.28 px) changes +0.8% from column 140 to 1455, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 188.8 px/in there. The axis is the tube's centre line (tilt +0.26°, rms 0.06 px). Lengths then scaled by 1.0145 so that the end faces are primary-arms-slx-1-6x24-gen-iv.length = 10.4 in apart: at the tube's scale they read 10.251 (-1.4%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.137 in over radius 0.589 (rms 0.002), the rear end's rim sags 0.147 in over radius 0.851 (rms 0.002)","method":"y_max in x [2.0, 3.3] of the traced outline (tools/trace.py); the throw lever's tip above the tube's axis (the left side, mirrored)","via":"harvest"}}],"adopt":{"from":"right","reason":"The right side is the photo the outlines are traced from; the left side, mirrored and traced on its own, agrees within its ±."}},"windage_reach":{"label":"windage reach","kind":"length","measurements":[{"id":"plan","value":1.234,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv f2c0f052f001 (Primary Arms, SLx 1-6x24 Second Focal Plane Optic Manual, the sheet numbered 4: the scope from above, 700 x 174 px)","scaleRef":"scale from primary-arms-slx-1-6x24-gen-iv.tube_od = 1.1811 in, the tube's own width column by column: 77.0 px over columns 14–100, 77.0 px over columns 106–196, 77.3 px over columns 308–384, 77.3 px over columns 390–462; a line through them (rms 0.09 px) changes +0.6% from column 14 to 462, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 350)/width, the lens's axis taken to meet the image at column 350; 65.4 px/in there. The axis is the tube's centre line (tilt +0.34°, rms 0.10 px). Lengths then scaled by 0.9998 so that the end faces are primary-arms-slx-1-6x24-gen-iv.length = 10.4 in apart: at the tube's scale they read 10.402 (+0.0%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.136 in over radius 0.586 (rms 0.010), the rear end's rim sags 0.124 in over radius 0.853 (rms 0.005)","method":"y_max in x [5.8, 7.5] of the traced outline (tools/trace.py); the windage turret's cap, its furthest point from the tube's axis toward the scope's right","via":"harvest"}}]},"illumination_reach":{"label":"illumination reach","kind":"length","measurements":[{"id":"plan","value":1.387,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv f2c0f052f001 (Primary Arms, SLx 1-6x24 Second Focal Plane Optic Manual, the sheet numbered 4: the scope from above, 700 x 174 px)","scaleRef":"scale from primary-arms-slx-1-6x24-gen-iv.tube_od = 1.1811 in, the tube's own width column by column: 77.0 px over columns 14–100, 77.0 px over columns 106–196, 77.3 px over columns 308–384, 77.3 px over columns 390–462; a line through them (rms 0.09 px) changes +0.6% from column 14 to 462, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 350)/width, the lens's axis taken to meet the image at column 350; 65.4 px/in there. The axis is the tube's centre line (tilt +0.34°, rms 0.10 px). Lengths then scaled by 0.9998 so that the end faces are primary-arms-slx-1-6x24-gen-iv.length = 10.4 in apart: at the tube's scale they read 10.402 (+0.0%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.136 in over radius 0.586 (rms 0.010), the rear end's rim sags 0.124 in over radius 0.853 (rms 0.005)","method":"−y_min in x [5.8, 7.5] of the traced outline (tools/trace.py); the illumination knob's battery cap, its furthest point from the tube's axis toward the scope's left","via":"harvest"}}]},"saddle_flat_bottom":{"label":"saddle flat bottom","kind":"length","measurements":[{"id":"right","value":0.793,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv d9806411659f (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_03.jpg (the Aurora 5.56 yard sibling: the same body), right side: the turned body)","scaleRef":"scale from primary-arms-slx-1-6x24-gen-iv.tube_od = 1.1811 in, the tube's own width column by column: 216.7 px over columns 760–980, 216.8 px over columns 990–1210, 216.4 px over columns 1505–1760, 215.5 px over columns 1770–2035; a line through them (rms 0.27 px) changes -0.6% from column 760 to 2035, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 183.4 px/in there. The axis is the tube's centre line (tilt -0.19°, rms 0.08 px). Lengths then scaled by 1.0140 so that the end faces are primary-arms-slx-1-6x24-gen-iv.length = 10.4 in apart: at the tube's scale they read 10.256 (-1.4%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.106 in over radius 0.588 (rms 0.001), the rear end's rim sags 0.190 in over radius 0.855 (rms 0.002)","method":"−y_min in x [6.3, 6.9] of the traced outline (tools/trace.py); the saddle's underside below the axis, under the turrets' station","via":"harvest"}}]},"magnification_ring_r":{"label":"magnification ring r","kind":"length","measurements":[{"id":"right","value":0.91,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv d9806411659f (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_03.jpg (the Aurora 5.56 yard sibling: the same body), right side: the turned body)","scaleRef":"scale from primary-arms-slx-1-6x24-gen-iv.tube_od = 1.1811 in, the tube's own width column by column: 216.7 px over columns 760–980, 216.8 px over columns 990–1210, 216.4 px over columns 1505–1760, 215.5 px over columns 1770–2035; a line through them (rms 0.27 px) changes -0.6% from column 760 to 2035, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 183.4 px/in there. The axis is the tube's centre line (tilt -0.19°, rms 0.08 px). Lengths then scaled by 1.0140 so that the end faces are primary-arms-slx-1-6x24-gen-iv.length = 10.4 in apart: at the tube's scale they read 10.256 (-1.4%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.106 in over radius 0.588 (rms 0.001), the rear end's rim sags 0.190 in over radius 0.855 (rms 0.002)","method":"y_max in x [2.0, 3.2] of the traced outline (tools/trace.py); the magnification ring at its lugs' tops, above the axis (the body alone: what shows below the axis, under the throw lever)","via":"harvest"}}]},"eyepiece_r":{"label":"eyepiece r","kind":"length","measurements":[{"id":"right","value":0.873,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv d9806411659f (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_03.jpg (the Aurora 5.56 yard sibling: the same body), right side: the turned body)","scaleRef":"scale from primary-arms-slx-1-6x24-gen-iv.tube_od = 1.1811 in, the tube's own width column by column: 216.7 px over columns 760–980, 216.8 px over columns 990–1210, 216.4 px over columns 1505–1760, 215.5 px over columns 1770–2035; a line through them (rms 0.27 px) changes -0.6% from column 760 to 2035, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 183.4 px/in there. The axis is the tube's centre line (tilt -0.19°, rms 0.08 px). Lengths then scaled by 1.0140 so that the end faces are primary-arms-slx-1-6x24-gen-iv.length = 10.4 in apart: at the tube's scale they read 10.256 (-1.4%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.106 in over radius 0.588 (rms 0.001), the rear end's rim sags 0.190 in over radius 0.855 (rms 0.002)","method":"y_max in x [0.8, 1.8] of the traced outline (tools/trace.py); the eyepiece's housing above the axis","via":"harvest"}}]},"saddle_flat_top":{"label":"saddle flat top","kind":"length","measurements":[{"id":"right","value":0.739,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv d9806411659f (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_03.jpg (the Aurora 5.56 yard sibling: the same body), right side: the elevation turret)","scaleRef":"scale from primary-arms-slx-1-6x24-gen-iv.tube_od = 1.1811 in, the tube's own width column by column: 216.7 px over columns 760–980, 216.8 px over columns 990–1210, 216.4 px over columns 1505–1760, 215.5 px over columns 1770–2035; a line through them (rms 0.27 px) changes -0.6% from column 760 to 2035, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 183.4 px/in there. The axis is the tube's centre line (tilt -0.19°, rms 0.08 px). Lengths then scaled by 1.0140 so that the end faces are primary-arms-slx-1-6x24-gen-iv.length = 10.4 in apart: at the tube's scale they read 10.256 (-1.4%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.106 in over radius 0.588 (rms 0.001), the rear end's rim sags 0.190 in over radius 0.855 (rms 0.002)","method":"y_min of the traced outline (tools/trace.py); the elevation turret's foot on the saddle, above the axis","via":"harvest"}}]},"cap_d":{"label":"cap d","kind":"length","measurements":[{"id":"right","value":1.319,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv d9806411659f (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_03.jpg (the Aurora 5.56 yard sibling: the same body), right side: the elevation turret)","scaleRef":"scale from primary-arms-slx-1-6x24-gen-iv.tube_od = 1.1811 in, the tube's own width column by column: 216.7 px over columns 760–980, 216.8 px over columns 990–1210, 216.4 px over columns 1505–1760, 215.5 px over columns 1770–2035; a line through them (rms 0.27 px) changes -0.6% from column 760 to 2035, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 183.4 px/in there. The axis is the tube's centre line (tilt -0.19°, rms 0.08 px). Lengths then scaled by 1.0140 so that the end faces are primary-arms-slx-1-6x24-gen-iv.length = 10.4 in apart: at the tube's scale they read 10.256 (-1.4%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.106 in over radius 0.588 (rms 0.001), the rear end's rim sags 0.190 in over radius 0.855 (rms 0.002)","method":"width of the traced outline (tools/trace.py); the elevation cap across its lugs' tops (along the scope; the photo's lengths are 1.4% longer than its tube's scale has them, which is in this)","via":"harvest"}},{"id":"plan","value":1.302,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv f2c0f052f001 (Primary Arms, SLx 1-6x24 Second Focal Plane Optic Manual, the sheet numbered 4: the scope from above, 700 x 174 px)","scaleRef":"the traced plan outline's own (profiles.plan): the 30 mm tube column by column; its two published sizes agree to 0.02% in that photo","method":"the windage cap in profile, across its lugs' tops along the scope: 5.987 to 7.289 in","via":"harvest"}}],"adopt":{"from":"plan","reason":"A round cap is as wide as it is across, and the side photo's lengths along the scope are 1.4% longer than its tube's scale has them: at the tube's scale the side view reads 1.301. The plan photo, whose length and tube agree, reads the same cap 1.302."}},"saddle_x":{"label":"Turret saddle's middle ahead of the eyepiece's rear face (where the turrets' axes cross the optical axis)","kind":"length","measurements":[{"id":"right","value":6.604,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv d9806411659f (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_03.jpg, the Aurora 5.56 yard sibling: the same body; right side, 2200 x 1467)","scaleRef":"the traced outline's own: the 30 mm tube column by column, lengths to the published 10.4 in (profiles.turret)","method":"the middle of the elevation turret's traced outline, 5.944 to 7.263 in ahead of the eyepiece's rear face: a cap turned about its own upright axis","via":"harvest"}},{"id":"left","value":6.613,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv 3ff18059ddc4 (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_04.jpg, the Aurora 5.56 yard sibling: the same body; left side, 2200 x 1467)","scaleRef":"the left side's own trace, mirrored: the 30 mm tube column by column, lengths to the published 10.4 in","method":"the middle of the elevation turret's outline on the left side, 5.953 to 7.273 in","via":"harvest"}}],"adopt":{"from":"right","reason":"The right side is the photo the outlines are traced from; the left side, mirrored, agrees within 0.01 in."}},"saddle_radius":{"label":"Turret saddle, the ball's radius (about the turrets' station on the optical axis)","kind":"length","measurements":[{"id":"side","value":0.9468,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"sqrt(({.tube_front_from} - {.tube_rear_to}) * ({.tube_front_from} - {.tube_rear_to}) / 4 + {.tube_od} * {.tube_od} / 4)","via":"harvest"}}],"note":"The saddle is drawn as a ball about the turrets' station with a flat under each turret and one beneath, the tube running through it. The side outline meets the tube 0.74 in either side of the station, where a ball of this radius has the tube's radius; 0.61 in from the station its underside reads 0.72 in from the axis, where this ball has 0.723; and in the oblique photos (a7dbed155cd5, 58d97f74fa18) the saddle between two turrets is round. No photo is square to it between the turrets: the radius rests on the side view alone."},"width":{"label":"Overall width (across the windage turret's cap and the illumination knob's battery cap)","kind":"length","measurements":[{"id":"turrets","value":2.621,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.windage_reach} + {.illumination_reach}","via":"harvest"}}],"note":"No page states a width. The two side knobs don't stand out alike: the windage cap is the elevation cap again, 1.23 in out, and the illumination knob is a taller stack with the battery under its cap."},"magnification_ring_lug_places":{"label":"Magnification ring, the places for a lug round each of its two rows (the throw lever's dovetail stands in the one on top)","kind":"count","measurements":[{"id":"sides","value":18,"unit":"count","source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv d9806411659f (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_03.jpg, the Aurora 5.56 yard sibling: the same body; right side, 2200 x 1467) and references/primary-arms-slx-1-6x24-gen-iv 3ff18059ddc4 (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_04.jpg, the Aurora 5.56 yard sibling: the same body; left side, 2200 x 1467)","scaleRef":"the ring's own silhouette radius in each photo (166.5 and 170.5 px), about the tube's axis","method":"each side view shows half the turn. The ring's surface unrolled about the axis (rows to angles by the silhouette's radius, with the near side's enlargement for a lens 25 in off taken out: the end faces' rims show as arcs 12.7 and 10.4 degrees off square, and a ring 0.91 in in radius is 3.6% large at its middle from there), and the strength of its edges along the turn, over 136 degrees of it, set against itself (.cache/batch8/primary-arms-slx-1-6x24-gen-iv/an5.py): the lugs' edges repeat every 19.8 and 19.5 degrees in the right view's rear and front rows and every 19.8 and 19.6 in the left's (autocorrelation 0.37 to 0.48 at the peak; 0.32 to 0.46 at 20.0 degrees and nothing at 21.2). With nothing taken out for the lens they repeat every 20.2 to 20.5. Eight lugs show in each row in each view, their middles by eye on the unrolled pictures 20.2 (right) and 19.9 (left) degrees apart, the right view's all 4.3 degrees below a grid of twenties (its lens stood that much above the axis's plane, as the windage cap's middle 0.09 in under the axis says too). Twenty degrees: eighteen places to the turn","via":"harvest"}}],"note":"Two rows of lugs along the scope, a waist between them, the lugs of one row in line with the other's. Sixteen lugs are seen in each row over the two side views; the place on top holds the lever's dovetail, and the one underneath is at the silhouette's edge in both views and is taken as a lug: a view from either end would say (none is on file). The spacing is what is measured (seventeen places would put the lugs 21.2 degrees apart, which the edges' period rules out)."},"magnification_ring_lug_width":{"label":"Magnification ring, a lug's flat top across (round the ring)","kind":"length","measurements":[{"id":"sides","value":0.166,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv d9806411659f (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_03.jpg, the Aurora 5.56 yard sibling: the same body; right side, 2200 x 1467)","scaleRef":"the ring's own radius at its lugs' tops (magnification_ring_r)","method":"in the unrolled view a lug's flat top takes 10 to 11 degrees of the turn (-53 to -43, -12 to 0, 8 to 20 less its lower bevel): 10.5 degrees at 0.91 in","via":"harvest"}}]},"diopter_ring_lugs":{"label":"Diopter ring (the eyepiece's rear ring), the blocks round it","kind":"count","measurements":[{"id":"right","value":18,"unit":"count","source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv d9806411659f (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_03.jpg, the Aurora 5.56 yard sibling: the same body; right side, 2200 x 1467)","scaleRef":"the ring's own silhouette radius (159.5 px), about the tube's axis","method":"the ring's surface unrolled about the axis: the blocks' and pockets' edges fall on a grid 20 degrees apart from 60 above level to 60 below (seven edges), a block and a pocket to each 20 degrees: nine to the half turn seen. The strength of the ring's edges along the turn set against itself (.cache/batch8/primary-arms-slx-1-6x24-gen-iv/an6.py): they repeat every 19.3 to 19.4 degrees with the near side's enlargement for a lens 25 in off taken out, 19.9 to 20.0 with nothing taken out (autocorrelation 0.43 to 0.52; 0.08 to 0.21 at 21.2 degrees)","via":"harvest"}},{"id":"left","value":18,"unit":"count","source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv 3ff18059ddc4 (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_04.jpg, the Aurora 5.56 yard sibling: the same body; left side, 2200 x 1467)","scaleRef":"the ring's own silhouette radius (161.5 px), about the tube's axis","method":"the other half of the turn, the same way: the edges repeat every 19.7 to 19.8 degrees with the lens's nearness taken out, 20.3 to 20.4 with nothing taken out (autocorrelation 0.50 to 0.55; 0.15 to 0.35 at 21.2 degrees)","via":"harvest"}}],"adopt":{"from":"right","reason":"The two side views, each half the turn, give the same spacing: eighteen to the turn."},"note":"A block and a pocket by turns round the ring. Half the turn is seen; no view from the rear is on file."},"cap_lugs":{"label":"Turret caps (elevation and windage: the same cap), the lugs round each of its two rows","kind":"count","measurements":[{"id":"face-on","value":18,"unit":"count","source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv d9806411659f (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_03.jpg, the Aurora 5.56 yard sibling: the same body; right side, 2200 x 1467)","scaleRef":"the 30 mm tube beside it: 183.4 px/in in the axis's plane (the trace's own scale)","method":"the windage cap seen face-on, unwrapped about its centre (column 1368, row 786; 1440 samples a turn): at every radius from 101 to 110 px the pattern round it is carried by the eighteenth harmonic (amplitude 14 to 20 grey levels against under 2 elsewhere): eighteen scallops between eighteen lugs","via":"harvest"}}]},"illumination_knob_lugs":{"label":"Illumination knob, the lugs round its battery cap's rim","kind":"count","measurements":[{"id":"face-on","value":18,"unit":"count","source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv 3ff18059ddc4 (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_04.jpg, the Aurora 5.56 yard sibling: the same body; left side, 2200 x 1467)","scaleRef":"the 30 mm tube beside it: 188.8 px/in in the axis's plane (the trace's own scale)","method":"the knob seen face-on, unwrapped about its centre (column 809, row 759): from 104 to 113 px the pattern round it is carried by the eighteenth harmonic (amplitude 9 to 13 grey levels): eighteen","via":"harvest"}}]},"cap_medallion_d":{"label":"Turret caps, the round medallion in the middle of the top face (the PA mark)","kind":"length","measurements":[{"id":"face-on","value":0.6,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv d9806411659f (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_03.jpg, the Aurora 5.56 yard sibling: the same body; right side, 2200 x 1467)","scaleRef":"the 30 mm tube beside it: 183.4 px/in in the axis's plane (the trace's own scale); the cap's face stands 1.23 in nearer a lens 25 in off, so it shows 5% large: 192.7 px/in","method":"the mean brightness round the windage cap's centre steps at 56 to 59 px from it, the medallion's edge: 58 px","via":"harvest"}},{"id":"fde","value":0.64,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv 58d97f74fa18 (Primary Arms PA-SLX-1-6X24S-NOVA-FDE_04.jpg, this scope in flat dark earth from the rear right, 2200 x 1467)","scaleRef":"the windage cap's own width across its lugs (cap_d) in the same view, along the same direction","method":"same-plane ratio: the black disc is 135 px tall where the cap's face is 275","via":"harvest"}}],"adopt":{"from":"face-on","reason":"Read square on, at a known scale; the oblique's ratio agrees within its ±."},"note":"Black on the flat dark earth scope as on the black one: the one piece that keeps its colour."},"lever_width":{"label":"Throw lever, its fin across the scope","kind":"length","measurements":[{"id":"oblique","value":0.3,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv 58d97f74fa18 (Primary Arms PA-SLX-1-6X24S-NOVA-FDE_04.jpg, this scope in flat dark earth from the rear right, 2200 x 1467)","scaleRef":"the fin's own height above its base in the same view, 0.74 in by the traced lever (profiles.lever)","method":"same-view ratio: the fin is 55 px across where it stands 140 px tall; the view is from behind and to the right, which shows the width a little short (in the ±)","via":"harvest"}}],"note":"No view is square to it. From above (a7dbed155cd5) its base is a block as wide as the fin, with a pocket for two screws, on a dovetail a little wider."},"objective_bore_d":{"label":"Objective, the mouth's inside diameter (threaded inside)","kind":"length","measurements":[{"id":"oblique","value":1.02,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv a7dbed155cd5 (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_01.jpg, the sibling from the front right and steeply above, 2200 x 1467)","scaleRef":"the front rim's own outside diameter, the 30 mm tube","method":"same-plane ratio on a 2x crop: the mouth's inner ellipse is 345 px along the direction its outer rim is 400: 0.86 of 1.181 in","via":"harvest"}}]},"eyepiece_lens_d":{"label":"Ocular lens diameter (the glass, as it shows in the eyepiece's rear)","kind":"length","measurements":[{"id":"oblique","value":1.32,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv a56a99961f90 (Primary Arms PA-SLX-1-6X24S-NOVA_02.jpg, this scope from the rear left, 2200 x 1467)","scaleRef":"the eyepiece's own rear rim in the same view, 740 px along its long axis, taken as 1.746 in (twice the traced eyepiece's radius)","method":"same-plane ratio on a 2x crop: the glass is 560 px along the same direction, 0.757 of the rim. It sits a little way inside the rim, which shows it a percent or two small","via":"harvest"}}]},"eyepiece_rim_id":{"label":"Eyepiece, the rear rim's inside diameter","kind":"length","measurements":[{"id":"oblique","value":1.63,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv a56a99961f90 (Primary Arms PA-SLX-1-6X24S-NOVA_02.jpg, this scope from the rear left, 2200 x 1467)","scaleRef":"the eyepiece's own rear rim in the same view (as eyepiece_lens_d)","method":"the rim's wall is 25 px of the 740 px rim on each side: an inside diameter 0.93 of the outside","via":"harvest"}}]},"boss_behind_station":{"label":"The round plug on the saddle's lower left, its middle behind the turrets' station","kind":"length","measurements":[{"id":"left","value":0.235,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv 3ff18059ddc4 (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_04.jpg, the Aurora 5.56 yard sibling: the same body; left side, 2200 x 1467)","scaleRef":"the 30 mm tube beside it: 188.8 px/in in the axis's plane (the trace's own scale); lengths at the trace's 185.9 px/in","method":"the plug's middle at column 883, by eye on a 3x crop; the turrets' station is at column 839.3 (6.613 in from the rear face)","via":"harvest"}}],"note":"A small round slotted plug low on the saddle's left, behind and under the illumination knob; no page says what it is. It shows in the left side view and in this scope's own rear-left view (a56a99961f90)."},"boss_below_axis":{"label":"The round plug on the saddle's lower left, its middle below the optical axis in the side view","kind":"length","measurements":[{"id":"left","value":0.694,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv 3ff18059ddc4 (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_04.jpg, the Aurora 5.56 yard sibling: the same body; left side, 2200 x 1467)","scaleRef":"the 30 mm tube beside it: 188.8 px/in in the axis's plane (the trace's own scale)","method":"the plug's middle at row 890, by eye on a 3x crop; the axis is at row 758.9 there","via":"harvest"}}],"note":"On a ball of the saddle's radius that is 47 degrees below level: the plug points down and to the left."},"boss_d":{"label":"The round plug on the saddle's lower left, its diameter","kind":"length","measurements":[{"id":"left","value":0.3,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv 3ff18059ddc4 (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_04.jpg, the Aurora 5.56 yard sibling: the same body; left side, 2200 x 1467)","scaleRef":"the 30 mm tube beside it: 188.8 px/in in the axis's plane (the trace's own scale)","method":"the plug shows 53 px tall and 68 wide with its side, by eye on a 3x crop: about 57 px across its face","via":"harvest"}}]},"diopter_pocket_from":{"label":"Diopter ring, where its pockets begin ahead of the eyepiece's rear face","kind":"length","measurements":[{"id":"right","value":0.15,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv d9806411659f (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_03.jpg, the Aurora 5.56 yard sibling: the same body; right side, 2200 x 1467)","scaleRef":"the trace's own scale along the scope, 181.1 px/in","method":"the pockets' rear edges at column 154 in the unrolled view of the ring, less the near side's 35 px toward the rear, from the rear face at column 161","via":"harvest"}}],"note":"The ring's near side shows 0.19 in toward the rear of where it is (the rear end is seen from 12.7 degrees off square, the ring 0.855 in in radius): taken out of both readings. How deep the pockets are isn't read."},"diopter_pocket_to":{"label":"Diopter ring, where its pockets end ahead of the eyepiece's rear face","kind":"length","measurements":[{"id":"right","value":0.28,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv d9806411659f (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_03.jpg, the Aurora 5.56 yard sibling: the same body; right side, 2200 x 1467)","scaleRef":"the trace's own scale along the scope, 181.1 px/in","method":"the pockets' front edges at column 177 in the unrolled view, less the near side's 35 px toward the rear","via":"harvest"}}]},"illumination_slot_length":{"label":"Illumination knob, the coin slot across its battery cap","kind":"length","measurements":[{"id":"left","value":0.52,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv 3ff18059ddc4 (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_04.jpg, the Aurora 5.56 yard sibling: the same body; left side, 2200 x 1467)","scaleRef":"the 30 mm tube beside it, 188.8 px/in in the axis's plane; the cap's face stands 1.39 in nearer a lens 25 in off: 199.6 px/in","method":"the slot's ends 103 px apart on a 3x crop of the knob seen face-on","via":"harvest"}}]},"illumination_slot_width":{"label":"Illumination knob, the coin slot's width","kind":"length","measurements":[{"id":"left","value":0.06,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv 3ff18059ddc4 (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_04.jpg, the Aurora 5.56 yard sibling: the same body; left side, 2200 x 1467)","scaleRef":"as illumination_slot_length: 199.6 px/in at the cap's face","method":"the slot is about 12 px across on the same crop","via":"harvest"}}]},"illumination_slot_turned":{"label":"Illumination knob's coin slot as photographed: its angle from the scope's axis, rising toward the muzzle","kind":"angle","measurements":[{"id":"left","value":52,"unit":"deg","pm":4,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv 3ff18059ddc4 (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_04.jpg, the Aurora 5.56 yard sibling: the same body; left side, 2200 x 1467)","scaleRef":"the tube's axis in the same photo","method":"the slot runs 63 px along the scope and 82 px up, its upper end toward the muzzle","via":"harvest"}}],"note":"Where the cap was left when it was last screwed on: it turns."},"lever_screw_rear_x":{"label":"Throw lever, its rear screw ahead of the eyepiece's rear face","kind":"length","measurements":[{"id":"oblique","value":2.61,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv a7dbed155cd5 (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_01.jpg, the sibling from the front right and steeply above, 2200 x 1467)","scaleRef":"the lever's own base as traced (profiles.lever): the fin's front face at 2.495 in, the base's front end at 3.056","method":"the rear screw's head is a fifth of the way from the fin's front face to the base's front end, on a 3x crop","via":"harvest"}}],"note":"Two socket-head screws in a pocket in the top of the lever's base hold it to its dovetail. No view is square to them: their places are fractions of the base's length in the one view from above."},"lever_screw_front_x":{"label":"Throw lever, its front screw ahead of the eyepiece's rear face","kind":"length","measurements":[{"id":"oblique","value":2.78,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv a7dbed155cd5 (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_01.jpg, the sibling from the front right and steeply above, 2200 x 1467)","scaleRef":"as lever_screw_rear_x","method":"the front screw's head is halfway from the fin's front face to the base's front end, on the same crop","via":"harvest"}}]},"lever_screw_d":{"label":"Throw lever, a screw's head across","kind":"length","measurements":[{"id":"oblique","value":0.11,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/primary-arms-slx-1-6x24-gen-iv a7dbed155cd5 (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_01.jpg, the sibling from the front right and steeply above, 2200 x 1467)","scaleRef":"the lever's own width in the same view (lever_width)","method":"a head is a little over a third of the base's width on the same crop","via":"harvest"}}]},"diopter_pocket_depth":{"label":"The diopter ring's pockets: how deep","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows it in profile. It was a named constant in the script until 2026-10-13, 05:15, the same night the part was made; it is here so that what the page counts as assumed counts it.","via":"harvest"}}]},"knob_flute_depth":{"label":"The illumination knob's battery cap: how deep its flutes are","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows it in profile. It was a named constant in the script until 2026-10-13, 05:15, the same night the part was made; it is here so that what the page counts as assumed counts it.","via":"harvest"}}]},"coin_slot_depth":{"label":"The battery cap's coin slot: how deep","kind":"length","measurements":[{"id":"assumed","value":0.04,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows it in profile. It was a named constant in the script until 2026-10-13, 05:15, the same night the part was made; it is here so that what the page counts as assumed counts it.","via":"harvest"}}]},"plug_proud":{"label":"The plug on the saddle's lower left: how far it stands off the saddle","kind":"length","measurements":[{"id":"assumed","value":0.05,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows it in profile. It was a named constant in the script until 2026-10-13, 05:15, the same night the part was made; it is here so that what the page counts as assumed counts it.","via":"harvest"}}]},"objective_glass_recess":{"label":"The objective's glass behind the front face (the mouth is threaded and goes black)","kind":"length","measurements":[{"id":"assumed","value":0.4,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows it in profile. It was a named constant in the script until 2026-10-13, 05:15, the same night the part was made; it is here so that what the page counts as assumed counts it.","via":"harvest"}}]},"ocular_glass_recess":{"label":"The eye lens ahead of the eyepiece's rear face","kind":"length","measurements":[{"id":"assumed","value":0.25,"unit":"in","pm":0.08,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows it in profile. It was a named constant in the script until 2026-10-13, 05:15, the same night the part was made; it is here so that what the page counts as assumed counts it.","via":"harvest"}}]},"lever_screw_pocket_depth":{"label":"The throw lever's screw pocket below the base's top at its front end","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows it in profile. It was a named constant in the script until 2026-10-13, 05:15, the same night the part was made; it is here so that what the page counts as assumed counts it.","via":"harvest"}}]}}},{"subject":"primary-arms-slx-cantilever-30mm-mount","title":"Primary Arms SLx Cantilever 30mm Mount - 1.5 in","dimensions":{"optical_axis_above_rail":{"label":"Ring axis above the rail's top","kind":"length","measurements":[{"id":"maker","value":1.5,"unit":"in","stated":"1.5\" Optical centerline","source":{"type":"spec","publisher":"manufacturer","name":"Primary Arms, SLx Cantilever 30mm Mount - 1.5\" (PA-SLX-CM-30-1.5), product page","url":"https://www.primaryarms.com/primary-arms-slx-cantilever-30mm-mount-1-5in","retrieved":"2026-10-13","via":"harvest"},"note":"The page's features list. Its title says the same (\"SLx Cantilever 30mm Mount - 1.5\"\"); the item feed's meta text: \"features a 1.5in optic height\". What it is measured from isn't said: taken, as every maker's centreline height is, from the rail's top."}]},"ring_bore":{"label":"Tube diameter the rings are bored for","kind":"length","measurements":[{"id":"maker","value":30,"unit":"mm","stated":"For 30mm scope tubes","source":{"type":"spec","publisher":"manufacturer","name":"Primary Arms, SLx Cantilever 30mm Mount - 1.5\" (PA-SLX-CM-30-1.5), product page","url":"https://www.primaryarms.com/primary-arms-slx-cantilever-30mm-mount-1-5in","retrieved":"2026-10-13","via":"harvest"},"note":"The specifications table: \"Mount Compatibility 30mm\"."}]},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"maker","value":5.785,"unit":"oz","stated":"Weighs 5.785 oz.","source":{"type":"spec","publisher":"manufacturer","name":"Primary Arms, SLx Cantilever 30mm Mount - 1.5\" (PA-SLX-CM-30-1.5), product page","url":"https://www.primaryarms.com/primary-arms-slx-cantilever-30mm-mount-1-5in","retrieved":"2026-10-13","via":"harvest"},"note":"The features list; the specifications table: \"Weight 5.785 oz.\"."}],"note":"The 20 MOA sibling's page (PA-SLX-CM-30-1.5-20) carries the same \"Weighs 5.785 oz.\" to the thousandth, so one of the two pages has the other's figure; which isn't said. One shop's page gives 6.8 and 6.49 oz in two places (Black Bayou Armory, whose pictures are another mount's): not taken. The model's own metal comes to it: see the part's notes."},"ring_spacing":{"label":"The two rings, front face to front face (and middle to middle)","kind":"length","measurements":[{"id":"camera","value":3.6,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/primary-arms-slx-cantilever-30mm-mount 179c33be21ec (Primary Arms PA-SLX-CM-30-1.5_01.jpg, from the front right and a little above, 2200 x 1488)","scaleRef":"ring_bore: the four rims of the two bores, each a 30 mm circle","method":"A pinhole camera (its axis through the picture's middle; distance, focal length, where the bores' axis points and lies, the rings' spacing and their length left free) fitted to the outline of each bore's see-through region against the white background (an arc of the near rim and an arc of the far rim) and to the front ring's near rim found all the way round (303 edge points): 1023 points, rms 1.3 px over the 83% within 3 px (the rest are the split's gap and the far rims' shadowed edge). Two runs: 3.598 and 3.602 in; the lens 25 in off, the axis 46 degrees off the line of sight. The same fit has each bore 0.736 in long rim to rim. The ± is what the lens's axis off the picture's middle by 300 px would move it, and the two runs.","via":"harvest"}},{"id":"camera-rear","value":3.638,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/primary-arms-slx-cantilever-30mm-mount ebcd0767a140 (Primary Arms PA-SLX-CM-30-1.5_03.jpg, from the rear left and above, 2200 x 1460)","scaleRef":"ring_bore: the four rims of the two bores, each a 30 mm circle","method":"The same camera fitted to the outlines of the two bores' see-through regions in the other oblique view (no rim found all the way round here): 599 points, rms 1.1 px over the 82% within 3 px; the lens 31 in off, the axis 47.5 degrees off the line of sight; each bore 0.770 in long rim to rim, where the front-right view has 0.736 and the side view has the rings 0.765 face to face. One run. The ± is the first camera's.","via":"harvest"}},{"id":"slots","value":3.57,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"What the rail's pitch would make it: the rings' faces are 3.013 times as far apart as the cross bolts' ends in the left view (1392.8 px for 462.3) and 3.035 times as far apart as their heads in the right view (1199 px for 395.0), and three slots are 1.182 in: 3.56 to 3.59. A clamp's bolts are surely made to the pitch; that these three are three slots apart is itself read at the bores' scale (1.195 in).","via":"harvest"}}],"adopt":{"from":"camera","reason":"The bores are the one published size that shows, and the first camera is the better fitted of the two (a rim found all the way round as well as the see-through outlines; two runs within 0.004 in). Its figure lies between the other two, and its ± reaches both: the second camera reads 1.1% more, and the rail's pitch under the cross bolts 0.8% less. Every length read at this scale carries that 1%."},"note":"The length every other reading is scaled by: the only one that comes from the published 30 mm alone. Three readings, 2% from the least to the most: two cameras fitted to the bores in two oblique views, 1.1% apart, and what three rail slots under the cross bolts would make it, 0.8% under the first camera's. The first camera's is between the other two and its ± takes in both."},"ring_rear_x":{"label":"Rear ring, its middle ahead of the rear cross bolt","kind":"length","measurements":[{"id":"left","value":0.598,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/primary-arms-slx-cantilever-30mm-mount d0a5b183f1dc (Primary Arms PA-SLX-CM-30-1.5_02.jpg, left side square on, 2200 x 1467)","scaleRef":"ring_spacing: the two rings' front faces, 1392.5 px apart at their near edges (columns 118.5 and 1511.0), and their rear faces, 1393.0 (414.4 and 1807.4): 387 px/in at the depth of the rings' near edges","method":"The ring's two end faces at their near edges on rows through its side flat (columns 1511.0 and 1807.4, the lit edge's middle and the silhouette), their middle 1659.2; the rear cross bolt's end at column 1890.8 (the dark recess round each bolt's end, the middle of its extent; the three are 461.8 and 462.8 px apart). The view is level: both rings' top flats on row 266 and both splits on row 525.0. The bolt's end stands about 0.15 in further from the lens than the rings' edges, which is 0.007 in here: inside the ±.","via":"harvest"}}]},"ring_front_x":{"label":"Front ring, its middle ahead of the rear cross bolt","kind":"length","measurements":[{"id":"left","value":4.197,"unit":"in","pm":0.045,"source":{"type":"photo","photo":"references/primary-arms-slx-cantilever-30mm-mount d0a5b183f1dc (Primary Arms PA-SLX-CM-30-1.5_02.jpg, left side square on, 2200 x 1467)","scaleRef":"ring_spacing (387 px/in at the depth of the rings' near edges)","method":"The front ring's two end faces at their near edges (columns 118.5 and 414.4), their middle 266.45; the rear cross bolt's end at column 1890.8. The ± is the scale's 1% over this length.","via":"harvest"}}]},"ring_length":{"label":"Each ring's length along the tube (face to face)","kind":"length","measurements":[{"id":"left","value":0.765,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/primary-arms-slx-cantilever-30mm-mount d0a5b183f1dc (Primary Arms PA-SLX-CM-30-1.5_02.jpg, left side square on, 2200 x 1467)","scaleRef":"ring_spacing (387 px/in)","method":"Each ring between its end faces' near edges on rows 470 to 600: 295.9 px (front ring) and 296.4 (rear). The camera fitted to the bores in the front-right view has each bore 0.736 in rim to rim: the bores' mouths are broken by about 0.015 in each.","via":"harvest"}}]},"ring_top_above_axis":{"label":"Rings, their top flat above the axis","kind":"length","measurements":[{"id":"left","value":0.669,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/primary-arms-slx-cantilever-30mm-mount d0a5b183f1dc (Primary Arms PA-SLX-CM-30-1.5_02.jpg, left side square on, 2200 x 1467)","scaleRef":"ring_spacing (387 px/in)","method":"Both rings' top flats on row 266 against the split between cap and lower half on row 525.0 (the dark gap, rows 523 to 527, on a column through each ring): 259 px. The split is taken to be at the bore's middle height (the cap is a half ring). The cap is then 0.078 in thick over the tube.","via":"harvest"}}]},"ring_width":{"label":"Rings, across their side flats","kind":"length","measurements":[{"id":"camera","value":1.53,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/primary-arms-slx-cantilever-30mm-mount 179c33be21ec (Primary Arms PA-SLX-CM-30-1.5_01.jpg, from the front right and a little above, 2200 x 1488)","scaleRef":"ring_bore, through the pinhole camera fitted to the bores' four rims (ring_spacing's source); where each picked point lies along the mount is taken from the left side view","method":"The corner where the split's line on the front ring's right side flat meets the flat's front edge (picked at 1500, 793 on a gridded crop), 0.074 in behind the ring's front face: its line of sight meets that station 0.766 in from the bores' axis, which is half the width. Checked on the three cross bolts' heads, picked the same way at their own stations: they come out 1.503, 1.507 and 1.490 in below the axis (the side view: 1.507) and 0.689, 0.680 and 0.676 in out from it. A pixel is 0.002 in there; 0.02 in of station moves a reading 0.02.","via":"harvest"}}],"note":"No view is square across the mount: read through the camera fitted to the bores in the front-right view."},"ring_side_flat_above_axis":{"label":"Rings, the side flat's upper edge above the axis (where the cap's chamfer begins)","kind":"length","measurements":[{"id":"left","value":0.24,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/primary-arms-slx-cantilever-30mm-mount d0a5b183f1dc (Primary Arms PA-SLX-CM-30-1.5_02.jpg, left side square on, 2200 x 1467)","scaleRef":"ring_spacing (387 px/in)","method":"The line between the cap's lit chamfer and its darker side flat, row 432 on both rings, against the split on row 525.0.","via":"harvest"}}]},"ring_side_flat_below_axis":{"label":"Rings, the side flat's lower edge below the axis (where the lower half's chamfer begins)","kind":"length","measurements":[{"id":"left","value":0.25,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/primary-arms-slx-cantilever-30mm-mount d0a5b183f1dc (Primary Arms PA-SLX-CM-30-1.5_02.jpg, left side square on, 2200 x 1467)","scaleRef":"ring_spacing (387 px/in)","method":"The line between the lower half's side flat and the chamfer under it, rows 621 to 623 on both rings, against the split on row 525.0.","via":"harvest"}}]},"ring_top_flat_width":{"label":"Rings, the top flat's width across","kind":"length","measurements":[{"id":"chamfers","value":0.672,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{.ring_width} - 2 * ({.ring_top_above_axis} - {.ring_side_flat_above_axis})","via":"harvest"}}],"note":"Worked out, not read: the cap's two chamfers taken at 45 degrees between the side flats and the top flat. The cap's real section isn't a plain octagon: from the front right each screw's pair of holes stands on a shoulder flatter than 45 degrees (each hole's mouth is 60 px tall in the side view where a 45 degree face would show 89), under a curve up to the top flat. Not read."},"ring_corner_chamfer":{"label":"Rings, the chamfer between each side flat and each end face (its length along the tube)","kind":"length","measurements":[{"id":"left","value":0.074,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/primary-arms-slx-cantilever-30mm-mount d0a5b183f1dc (Primary Arms PA-SLX-CM-30-1.5_02.jpg, left side square on, 2200 x 1467)","scaleRef":"ring_spacing (387 px/in)","method":"On each ring's near side flat, the line where the flat ends (columns 147 and 385 on the front ring, 1545 and 1780 on the rear) against the end faces' near edges (118.5, 414.4; 1511.0, 1807.4): 27 to 29 px. Drawn at 45 degrees.","via":"harvest"}}]},"ring_screw_spacing":{"label":"Ring cap screws, the two on a side, centre to centre along the tube","kind":"length","measurements":[{"id":"left","value":0.453,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/primary-arms-slx-cantilever-30mm-mount d0a5b183f1dc (Primary Arms PA-SLX-CM-30-1.5_02.jpg, left side square on, 2200 x 1467)","scaleRef":"ring_spacing (387 px/in)","method":"Where the picture round one hole is found again at the other (normalised correlation of a 111 px patch): 177.0 px on the front ring, 173.8 on the rear.","via":"harvest"}}]},"ring_screw_hole_d":{"label":"Ring cap screws, the hole each sits in (its diameter)","kind":"length","measurements":[{"id":"left","value":0.23,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/primary-arms-slx-cantilever-30mm-mount d0a5b183f1dc (Primary Arms PA-SLX-CM-30-1.5_02.jpg, left side square on, 2200 x 1467)","scaleRef":"ring_spacing (387 px/in)","method":"Each hole's width along the tube on a row through it, 87 to 90 px (131 to 221 and 311 to 398 on the front ring). The holes go straight down through the cap's chamfer, so each shows as an ellipse 60 px tall.","via":"harvest"}}]},"ring_screw_hole_above_axis":{"label":"Ring cap screws, the hole's middle above the axis as the side sees it","kind":"length","measurements":[{"id":"left","value":0.333,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/primary-arms-slx-cantilever-30mm-mount d0a5b183f1dc (Primary Arms PA-SLX-CM-30-1.5_02.jpg, left side square on, 2200 x 1467)","scaleRef":"ring_spacing (387 px/in)","method":"Each hole's ellipse between rows 366 and 425, its middle 396, against the split on row 525.0.","via":"harvest"}}]},"arm_width":{"label":"The arm, across (the beam the rings stand on)","kind":"length","measurements":[{"id":"camera","value":0.75,"unit":"in","pm":0.07,"source":{"type":"photo","photo":"references/primary-arms-slx-cantilever-30mm-mount 179c33be21ec (Primary Arms PA-SLX-CM-30-1.5_01.jpg, from the front right and a little above, 2200 x 1488)","scaleRef":"ring_bore, through the pinhole camera fitted to the bores' four rims (ring_spacing's source)","method":"The two ends of the long pocket in the arm's right side (picked at 1545, 1140 and 1185, 1135), each at the station and height the left side view has that end of the left side's pocket: they come out 0.403 and 0.346 in out from the axis's plane, and 0.986 and 1.231 in below the axis where the side view has 0.989 and 1.248. Twice their mean.","via":"harvest"}}],"note":"A weak reading: two points on one side, the other side taken to mirror it."},"arm_pocket_depth":{"label":"The pockets in the arm's sides and under the rear ring, their depth","kind":"length","measurements":[{"id":"camera","value":0.19,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/primary-arms-slx-cantilever-30mm-mount 179c33be21ec (Primary Arms PA-SLX-CM-30-1.5_01.jpg, from the front right and a little above, 2200 x 1488)","scaleRef":"ring_bore, through the pinhole camera fitted to the bores' four rims (442 px/in at the front ring, the axis 46 degrees off the line of sight)","method":"The wall of the long pocket's rear end as that view shows it, from the pocket's rim (column 1187) to its floor's edge (1245): 58 px across the mount, which that view foreshortens by the sine of 44 degrees. Neither side view shows background through either pocket: they are blind, one in each side, with a web between.","via":"harvest"}}]},"clamp_bolt_spacing":{"label":"Clamp cross bolts, centre to centre (three bolts, two equal spacings)","kind":"length","measurements":[{"id":"slots","value":1.182,"unit":"in","source":{"type":"derived","expr":"3 * {std.picatinny.slot_pitch}","via":"harvest"}},{"id":"left","value":1.195,"unit":"in","pm":0.014,"source":{"type":"photo","photo":"references/primary-arms-slx-cantilever-30mm-mount d0a5b183f1dc (Primary Arms PA-SLX-CM-30-1.5_02.jpg, left side square on, 2200 x 1467)","scaleRef":"ring_spacing (387 px/in at the rings' near edges; the bolts' ends stand about 0.15 in further off, 0.3%)","method":"The dark recess round each bolt's end in the three bosses, the middle of its extent: columns 966.2, 1428.0 and 1890.8 on rows 1107.8, 1108.8 and 1108.0. The right view's three heads are 395.0 px apart each.","via":"harvest"}}],"adopt":{"from":"slots","reason":"The three bolts lie in recoil slots, which are a whole number of pitches apart, and the reading at the bores' own scale is three pitches within its ±: 1.195 against 1.182. A slot's clearance round a 0.16 in bolt would allow either."},"note":"Each bolt lies in a recoil slot (Primary Arms: \"dual machined recoil lugs and 3 cross bolt lugs\"). Their ends read 461.8 and 462.8 px apart in the left view: 1.195 in at the bores' scale, three slots (1.182) within 1.1%, which is that scale's own ±. Here the spacing is the reading and the pitch its check."},"clamp_bolt_below_rail_top":{"label":"Clamp cross bolts, their axis below the rail's top","kind":"length","measurements":[{"id":"left","value":0.007,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/primary-arms-slx-cantilever-30mm-mount d0a5b183f1dc (Primary Arms PA-SLX-CM-30-1.5_02.jpg, left side square on, 2200 x 1467)","scaleRef":"ring_spacing (387 px/in), and optical_axis_above_rail","method":"The bolts' ends on row 1108.2 against the rings' split on row 525.0: 583.2 px, 1.507 in, less the published 1.5. The ± is the scale's 1% over that height and the published figure's last digit isn't in it.","via":"harvest"}}],"note":"The maker's 1.5 in is to the rail's top; the bolts' axes read 1.507 in below the rings' axis. With the bolt 0.16 in across, its underside is then 0.087 in down a recoil slot 0.118 deep."},"clamp_bolt_end_d":{"label":"Clamp cross bolts, the threaded end's diameter as it shows in the left side's bosses","kind":"length","measurements":[{"id":"left","value":0.16,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/primary-arms-slx-cantilever-30mm-mount d0a5b183f1dc (Primary Arms PA-SLX-CM-30-1.5_02.jpg, left side square on, 2200 x 1467)","scaleRef":"ring_spacing (387 px/in)","method":"The bright end of each bolt inside its dark recess, 60 to 64 px across; the recess itself (clamp_bolt_recess_d) 91 px.","via":"harvest"}}]},"clamp_bolt_recess_d":{"label":"Clamp cross bolts, the recess round each bolt's end in the left side's bosses","kind":"length","measurements":[{"id":"left","value":0.235,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/primary-arms-slx-cantilever-30mm-mount d0a5b183f1dc (Primary Arms PA-SLX-CM-30-1.5_02.jpg, left side square on, 2200 x 1467)","scaleRef":"ring_spacing (387 px/in)","method":"The dark ring round each bolt's end, 90 to 92 px across (1382 to 1474 round the middle one).","via":"harvest"}}]},"clamp_bolt_head_d":{"label":"Clamp cross bolts, the head's diameter (Torx, on the right)","kind":"length","measurements":[{"id":"right","value":0.31,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/primary-arms-slx-cantilever-30mm-mount 561a3f71b28c (Primary Arms PA-SLX-CM-30-1.5_04.jpg, right side from about 6 degrees above, 2200 x 1467)","scaleRef":"clamp_bolt_spacing: the three heads 395.0 px apart each (columns 430.5, 825.5, 1220.5), 334 px/in at the clamp bar's face","method":"Each head 104 to 106 px across; the counterbore it sits in 127 to 129 px (clamp_bolt_counterbore_d). This view is from above (the rings' caps read 15% tall against their length, and the screws show at the bottoms of their holes): only what lies in the bar's own face is read on it.","via":"harvest"}}]},"clamp_bolt_counterbore_d":{"label":"Clamp cross bolts, the counterbore each head sits in (in the clamp bar)","kind":"length","measurements":[{"id":"right","value":0.385,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/primary-arms-slx-cantilever-30mm-mount 561a3f71b28c (Primary Arms PA-SLX-CM-30-1.5_04.jpg, right side from about 6 degrees above, 2200 x 1467)","scaleRef":"clamp_bolt_spacing: the three heads 395.0 px apart each (columns 430.5, 825.5, 1220.5), 334 px/in at the clamp bar's face","method":"Each head 104 to 106 px across; the counterbore it sits in 127 to 129 px (clamp_bolt_counterbore_d). This view is from above (the rings' caps read 15% tall against their length, and the screws show at the bottoms of their holes): only what lies in the bar's own face is read on it.","via":"harvest"},"note":"The dark gap round each head, 127 and 129 px across its outside (762 to 889 round the middle one)."}]},"clamp_bolt_head_h":{"label":"Clamp cross bolts, the head's height (how deep its counterbore is)","kind":"length","measurements":[{"id":"assumed","value":0.1,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the heads sit in their counterbores about flush with the bar's face in both views that show them; no view shows a head in profile.","via":"harvest"}}]},"clamp_bolt_recess_depth":{"label":"Clamp cross bolts, how deep the recess round each bolt's end is in the left side's bosses","kind":"length","measurements":[{"id":"assumed","value":0.05,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the bolts' ends stand a little below the bosses' faces in the left view; how far isn't read.","via":"harvest"}}]},"clamp_bolt_socket_d":{"label":"Clamp cross bolts, the six-lobed socket in each head, across its points","kind":"length","measurements":[{"id":"right","value":0.177,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/primary-arms-slx-cantilever-30mm-mount 561a3f71b28c (Primary Arms PA-SLX-CM-30-1.5_04.jpg, right side from about 6 degrees above, 2200 x 1467)","scaleRef":"clamp_bolt_spacing: the three heads 395.0 px apart each (columns 430.5, 825.5, 1220.5), 334 px/in at the clamp bar's face","method":"Each head 104 to 106 px across; the counterbore it sits in 127 to 129 px (clamp_bolt_counterbore_d). This view is from above (the rings' caps read 15% tall against their length, and the screws show at the bottoms of their holes): only what lies in the bar's own face is read on it.","via":"harvest"},"note":"The middle head's socket on a gridded crop: its six lobes' tips lie on a circle 58 to 60 px across (columns 793 to 852, rows 1040 to 1098), a lobe pointing up. Six lobes counted round it, on all three heads."}]},"clamp_bolt_socket_waist_d":{"label":"Clamp cross bolts, the socket across its valleys (between the lobes)","kind":"length","measurements":[{"id":"right","value":0.125,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/primary-arms-slx-cantilever-30mm-mount 561a3f71b28c (Primary Arms PA-SLX-CM-30-1.5_04.jpg, right side from about 6 degrees above, 2200 x 1467)","scaleRef":"clamp_bolt_spacing: the three heads 395.0 px apart each (columns 430.5, 825.5, 1220.5), 334 px/in at the clamp bar's face","method":"Each head 104 to 106 px across; the counterbore it sits in 127 to 129 px (clamp_bolt_counterbore_d). This view is from above (the rings' caps read 15% tall against their length, and the screws show at the bottoms of their holes): only what lies in the bar's own face is read on it.","via":"harvest"},"note":"A weak reading: the socket's dark floor between opposite valleys, 40 to 44 px on the same crop; the lobes' flanks are lit and shadowed unevenly."}]},"clamp_bolt_socket_depth":{"label":"Clamp cross bolts, the socket's depth as drawn","kind":"length","measurements":[{"id":"assumed","value":0.06,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows a socket in section.","via":"harvest"}}]},"clamp_bar_facet_top_h":{"label":"The clamp bar, the facet along its upper edge between the pads round the heads: its height on the bar's face","kind":"length","measurements":[{"id":"right","value":0.177,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/primary-arms-slx-cantilever-30mm-mount 561a3f71b28c (Primary Arms PA-SLX-CM-30-1.5_04.jpg, right side from about 6 degrees above, 2200 x 1467)","scaleRef":"clamp_bolt_spacing: the three heads 395.0 px apart each (columns 430.5, 825.5, 1220.5), 334 px/in at the clamp bar's face","method":"Each head 104 to 106 px across; the counterbore it sits in 127 to 129 px (clamp_bolt_counterbore_d). This view is from above (the rings' caps read 15% tall against their length, and the screws show at the bottoms of their holes): only what lies in the bar's own face is read on it.","via":"harvest"},"note":"On a column midway between the middle and the front heads (1023): the lit facet from row 968, the bar's top, to row 1027, where the darker flat face begins. The same on a column between the rear and the middle heads, in shadow there."}]},"clamp_bar_facet_bottom_h":{"label":"The clamp bar, the facet along its lower edge between the pads: its height on the bar's face","kind":"length","measurements":[{"id":"right","value":0.117,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/primary-arms-slx-cantilever-30mm-mount 561a3f71b28c (Primary Arms PA-SLX-CM-30-1.5_04.jpg, right side from about 6 degrees above, 2200 x 1467)","scaleRef":"clamp_bolt_spacing: the three heads 395.0 px apart each (columns 430.5, 825.5, 1220.5), 334 px/in at the clamp bar's face","method":"Each head 104 to 106 px across; the counterbore it sits in 127 to 129 px (clamp_bolt_counterbore_d). This view is from above (the rings' caps read 15% tall against their length, and the screws show at the bottoms of their holes): only what lies in the bar's own face is read on it.","via":"harvest"},"note":"On the same column: from row 1097, where the flat face ends, to the bar's foot on row 1136."}]},"clamp_bar_pad_top_half":{"label":"The clamp bar, the flat pad round each head: half its length at the bar's upper and lower edges","kind":"length","measurements":[{"id":"right","value":0.09,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/primary-arms-slx-cantilever-30mm-mount 561a3f71b28c (Primary Arms PA-SLX-CM-30-1.5_04.jpg, right side from about 6 degrees above, 2200 x 1467)","scaleRef":"clamp_bolt_spacing: the three heads 395.0 px apart each (columns 430.5, 825.5, 1220.5), 334 px/in at the clamp bar's face","method":"Each head 104 to 106 px across; the counterbore it sits in 127 to 129 px (clamp_bolt_counterbore_d). This view is from above (the rings' caps read 15% tall against their length, and the screws show at the bottoms of their holes): only what lies in the bar's own face is read on it.","via":"harvest"},"note":"On a row just under the bar's top (980): the pad's own lit edge round the middle head from column 795 to 855, about its head at 825.5."}]},"clamp_bar_pad_half":{"label":"The clamp bar, the flat pad round each head: half its length where the facets end on the face","kind":"length","measurements":[{"id":"right","value":0.21,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/primary-arms-slx-cantilever-30mm-mount 561a3f71b28c (Primary Arms PA-SLX-CM-30-1.5_04.jpg, right side from about 6 degrees above, 2200 x 1467)","scaleRef":"clamp_bolt_spacing: the three heads 395.0 px apart each (columns 430.5, 825.5, 1220.5), 334 px/in at the clamp bar's face","method":"Each head 104 to 106 px across; the counterbore it sits in 127 to 129 px (clamp_bolt_counterbore_d). This view is from above (the rings' caps read 15% tall against their length, and the screws show at the bottoms of their holes): only what lies in the bar's own face is read on it.","via":"harvest"},"note":"A weak reading on a gridded crop: at the facets' inner edges each runs from just outside one head's counterbore to just outside the next's (about 70 px from each head's middle; the counterbore is 64)."}]},"clamp_bar_facet_depth":{"label":"The clamp bar's facets, how far in from its face they reach at its upper and lower edges","kind":"length","measurements":[{"id":"assumed","value":0.08,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the facets show from the side and from the front right, and no view on file shows the bar end on.","via":"harvest"}}]},"clamp_bar_length":{"label":"The clamp bar (the separate piece on the right), its length","kind":"length","measurements":[{"id":"right","value":3.2,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/primary-arms-slx-cantilever-30mm-mount 561a3f71b28c (Primary Arms PA-SLX-CM-30-1.5_04.jpg, right side from about 6 degrees above, 2200 x 1467)","scaleRef":"clamp_bolt_spacing: the three heads 395.0 px apart each (columns 430.5, 825.5, 1220.5), 334 px/in at the clamp bar's face","method":"Each head 104 to 106 px across; the counterbore it sits in 127 to 129 px (clamp_bolt_counterbore_d). This view is from above (the rings' caps read 15% tall against their length, and the screws show at the bottoms of their holes): only what lies in the bar's own face is read on it.","via":"harvest"},"note":"Its ends at columns 293 and 1362: 1069 px. It reaches 0.41 in behind the rear bolt (clamp_bar_rear_x) and 0.42 ahead of the front one."}]},"clamp_bar_rear_x":{"label":"The clamp bar, its rear end behind the rear cross bolt","kind":"length","measurements":[{"id":"right","value":0.41,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/primary-arms-slx-cantilever-30mm-mount 561a3f71b28c (Primary Arms PA-SLX-CM-30-1.5_04.jpg, right side from about 6 degrees above, 2200 x 1467)","scaleRef":"clamp_bolt_spacing: the three heads 395.0 px apart each (columns 430.5, 825.5, 1220.5), 334 px/in at the clamp bar's face","method":"Each head 104 to 106 px across; the counterbore it sits in 127 to 129 px (clamp_bolt_counterbore_d). This view is from above (the rings' caps read 15% tall against their length, and the screws show at the bottoms of their holes): only what lies in the bar's own face is read on it.","via":"harvest"},"note":"Column 293 against the rear head at 430.5: 137.5 px."}]},"clamp_bar_outer_z":{"label":"The clamp bar's outer face (the bolt heads' faces), out from the rail's middle","kind":"length","measurements":[{"id":"camera","value":0.68,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/primary-arms-slx-cantilever-30mm-mount 179c33be21ec (Primary Arms PA-SLX-CM-30-1.5_01.jpg, from the front right and a little above, 2200 x 1488)","scaleRef":"ring_bore, through the pinhole camera fitted to the bores' four rims (ring_spacing's source); where each picked point lies along the mount is taken from the left side view","method":"The corner where the split's line on the front ring's right side flat meets the flat's front edge (picked at 1500, 793 on a gridded crop), 0.074 in behind the ring's front face: its line of sight meets that station 0.766 in from the bores' axis, which is half the width. Checked on the three cross bolts' heads, picked the same way at their own stations: they come out 1.503, 1.507 and 1.490 in below the axis (the side view: 1.507) and 0.689, 0.680 and 0.676 in out from it. A pixel is 0.002 in there; 0.02 in of station moves a reading 0.02.","via":"harvest"},"note":"The three bolt heads' middles through the fitted camera: 0.689, 0.680 and 0.676 in out from the bores' axis, which is taken to stand over the rail's middle. The heads sit in counterbores, about flush with the bar's face."}]},"clamp_bar_thickness":{"label":"The clamp bar, its thickness across (to the seam with the base)","kind":"length","measurements":[{"id":"assumed","value":0.25,"unit":"in","pm":0.06,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view shows the seam between the bar and the base from above or end on. It puts the bar's inner face 0.03 in outside the rail's widest.","via":"harvest"}}]},"base_left_z":{"label":"The base's fixed side (the three bosses' faces), out from the rail's middle","kind":"length","measurements":[{"id":"assumed","value":0.68,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the fixed side taken as far out on the left as the clamp bar's face reads on the right (clamp_bar_outer_z). The one view of the left side from an angle (ebcd0767a140) wasn't brought to a camera in the time there was.","via":"harvest"}}]},"base_top_y":{"label":"The base's top face above the rail's top","kind":"length","measurements":[{"id":"left","value":0.234,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/primary-arms-slx-cantilever-30mm-mount d0a5b183f1dc (Primary Arms PA-SLX-CM-30-1.5_02.jpg, left side square on, 2200 x 1467)","scaleRef":"ring_spacing (387 px/in)","method":"The bosses' upper edge on row 1015 against the bolts' ends on row 1108.2, less clamp_bolt_below_rail_top.","via":"harvest"}}]},"base_bottom_y":{"label":"The clamp's foot below the rail's top","kind":"length","measurements":[{"id":"left","value":0.249,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/primary-arms-slx-cantilever-30mm-mount d0a5b183f1dc (Primary Arms PA-SLX-CM-30-1.5_02.jpg, left side square on, 2200 x 1467)","scaleRef":"ring_spacing (387 px/in)","method":"The bosses' feet on row 1202 against the bolts' ends on row 1108.2, plus clamp_bolt_below_rail_top.","via":"harvest"}}]},"base_boss_chamfer":{"label":"The bosses' and the clamp bar's edge chamfers","kind":"length","measurements":[{"id":"left","value":0.07,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/primary-arms-slx-cantilever-30mm-mount d0a5b183f1dc (Primary Arms PA-SLX-CM-30-1.5_02.jpg, left side square on, 2200 x 1467)","scaleRef":"ring_spacing (387 px/in)","method":"The lit band along each boss's upper edge, rows 1015 to 1045 (30 px, 0.078 in), and the one along its foot (22 px): drawn as one 45 degree chamfer of their mean.","via":"harvest"}}]},"mount_length":{"label":"Clamp length along the rail (at its foot)","kind":"length","measurements":[{"id":"left","value":3.03,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/primary-arms-slx-cantilever-30mm-mount d0a5b183f1dc (Primary Arms PA-SLX-CM-30-1.5_02.jpg, left side square on, 2200 x 1467)","scaleRef":"ring_spacing (387 px/in)","method":"The fixed side's foot (the silhouette's lowest rows) from column 838 to 2012: 1174 px. The clamp bar on the other side is 3.2 in long.","via":"harvest"}}]},"cap_screw_d":{"label":"Ring cap screws, the head as drawn at the bottom of each hole","kind":"length","measurements":[{"id":"assumed","value":0.2,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the screws' heads show only as glints at the bottoms of their holes (0.23 in across). Their size and driver aren't published (\"Rings - 16-18 in. lbs.\").","via":"harvest"}}]},"cap_screw_depth":{"label":"Ring cap screws, the hole's floor (where the head sits) below the hole's middle as the side sees it","kind":"length","measurements":[{"id":"assumed","value":0.075,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the heads sit down their holes in every view; how far isn't read. A hole 0.23 in across standing against the side flat's plane has its inner wall 0.535 in from the rings' axis, over the tube: its floor can't be lower than 0.25 in above the axis, which is this figure and no more.","via":"harvest"}}]},"lower_pocket_depth":{"label":"The two pockets in each side of each ring's lower half, their depth into the chamfer","kind":"length","measurements":[{"id":"assumed","value":0.06,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the pockets under the cap screws are shallow cuts in the lower half's chamfer in both three-quarter views; their depth isn't read.","via":"harvest"}}]},"ring_split_width":{"label":"Rings, the gap between cap and lower half as the side shows it","kind":"length","measurements":[{"id":"left","value":0.012,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/primary-arms-slx-cantilever-30mm-mount d0a5b183f1dc (Primary Arms PA-SLX-CM-30-1.5_02.jpg, left side square on, 2200 x 1467)","scaleRef":"ring_spacing (387 px/in)","method":"The dark line between the two halves on a column through each ring: rows 523 to 527, under a level of 20 of 255 (4 to 5 px). With no tube in the rings: the gap a clamped scope leaves isn't published.","via":"harvest"}}]},"ring_split_depth":{"label":"Rings, how deep the split is drawn (a groove round the ring: the rings are drawn closed on the tube)","kind":"length","measurements":[{"id":"assumed","value":0.012,"unit":"in","pm":0.006,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the split goes through to the bore; it is drawn as a groove as deep as it is wide, so that the ring stays one closed piece round the tube.","via":"harvest"}}]},"cap_screw_head_h":{"label":"Ring cap screws, how far the head as drawn stands above its hole's floor","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows a cap screw's head in profile.","via":"harvest"}}]},"clamp_bolt_end_below_face":{"label":"Clamp cross bolts, the threaded end below the boss's face","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the bolts' ends show inside their recesses in the left view, a little under the bosses' faces; no view on file shows one in profile.","via":"harvest"}}]},"edge_break":{"label":"The break on the mount's machined edges, as drawn","kind":"length","measurements":[{"id":"assumed","value":0.006,"unit":"in","pm":0.004,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the photos show every edge broken by a fine lit line a pixel or two wide; its size isn't read.","via":"harvest"}}]},"hardware_weight":{"label":"The steel hardware as drawn (three cross bolts, eight cap screws)","kind":"mass","measurements":[{"id":"steel","value":0.83,"unit":"oz","pm":0.2,"source":{"type":"derived","basis":"Three cross bolts 0.16 in across and 1.4 in long with 0.31 in heads, and eight cap screws taken as 0.14 in across and 0.45 in long with 0.2 in heads, at std.density.steel: about 0.18 cubic inches. The screws' sizes aren't published.","via":"harvest"}}],"note":"Worked out, not published: the pieces' drawn volume as steel. The maker says only \"Steel hardware\"."}}},{"subject":"psa-stealth-stripped-lower","title":"Palmetto State Armory PSA AR-15 \"Stealth\" Stripped Lower Receiver (39296)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"metal","value":8.47,"unit":"oz","pm":0.85,"source":{"type":"derived","basis":"This part's own model's metal: the closed volume of app/public/models/psa-stealth-stripped-lower.glb as its script built it (5.189 cubic inches: the traced outline at the Army drawing's widths, its pocket, well, bore and holes cut; the manifest's volume_in3) times what a cubic inch of 7075 weighs (std.density.aluminium_7075, 1.632 oz): 5.189 x 1.632 = 8.47 oz. The page: 'Forged 7075 Aluminum', '7075-T6 aluminum'.","via":"user"}}],"note":"WORKED OUT, not published: the page states no weight (no 'weight', 'oz' or 'lb' anywhere in its text as the user saved it on 2026-10-12), and no seller's or reviewer's page is on file. The ± is a tenth: what a model with its inside edges square, its thread uncut, its lightening pockets by the selector left out and its right side taken from the standard forging can be off by. For scale only, not a source: the catalog's Workhorse, a forged mil-spec lower, is 8.22 oz by its maker. app/tests/psa-stealth-stripped-lower.test.ts holds the model's volume to this figure, so a rebuilt model that changes it says so."},"width":{"label":"Receiver maximum width (Z)","kind":"length","measurements":[{"id":"std","value":0.88,"unit":"in","pm":0.008,"source":{"type":"derived","expr":"{std.ar15.lower_body_width}","via":"harvest"},"note":"Palmetto State Armory: 'These forged lowers are quality made by a mil-spec contractor using 7075-T6 aluminum' (the page as the user saved it, 2026-10-12). The body's width is the Army drawing's (8448608, Section C-C). No page states a width and no photo on file looks along the receiver or down onto it."}],"note":"The body's is the drawing's; the well's walls (std.ar15.magwell_outside_width) and the tower's ring (std.ar15.buffer_tower_od) stand wider and are drawn at the drawing's too."},"buffer_axis_above_pin":{"label":"Receiver extension (bore) axis above the takedown pin centre","kind":"length","measurements":[{"id":"std","value":0.8775,"unit":"in","pm":0.0015,"source":{"type":"derived","expr":"{std.ar15.bore_axis_y}","via":"harvest"},"note":"A mil-spec lower: the threaded hole's centre is the drawing's (.629 above the deck). The left photo is consistent with it and no more: the ring is seen from ahead and its rims aren't circles a 546 px picture can be fitted to (its silhouette tops out at 1.605 for the drawing's 1.5735: the ring's near rim, 0.7 in nearer the lens than the centre plane, seen from a lens that stands below its top's level)."}]},"magazine_seat_x":{"label":"Magazine seat, X (a seated magazine's frame origin ahead of the takedown pin)","kind":"length","measurements":[{"id":"milspec","value":3.4915,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{bad-workhorse-lower.magazine_seat_x}","via":"user"},"note":"Where a magazine seats in a mil-spec well: from the Army drawing's well and catch slot and the user's own magazine, recorded on the Workhorse. This lower's well is mil-spec by its maker's sentence, and its left photo has the catch's slot and hole where the drawing puts them (the hole at X 3.289, Y -0.564 for the drawing's 3.291, -0.565). No photo of a magazine seated in it is on file."}]},"magazine_seat_y":{"label":"Magazine seat, Y (the feed-lip top of a seated magazine)","kind":"length","measurements":[{"id":"milspec","value":1.003,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{bad-workhorse-lower.magazine_seat_y}","via":"user"},"note":"As magazine_seat_x: the standard well's and the catch's, not this receiver's outside."}]},"grip_mating_y":{"label":"Receiver underside behind the step (where a grip's flat top bears), Y","kind":"length","measurements":[{"id":"left","value":-1.071,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 92d56fedaacf (left side on white: Palmetto State Armory's gallery picture 7a4a7701.jpg (546 x 546), from the page the user saved 2026-10-12)","scaleRef":"frame from the reviewed holes takedown, pivot (59.4 px/in, rms 0.000 in over 2 points)","method":"y_min in x [-0.25, -0.12] of the traced outline (tools/trace.py)","via":"user"},"note":"The outline's flat just behind the lug's rear face: the left side's reading of where a grip's flat top bears (the seat itself is the drawing's: grip_seat_y)."}],"note":"The outline's flat just behind the lug's rear face: the left side's reading of where a grip's flat top bears. The seat itself is the drawing's (grip_seat_y)."},"grip_seat_y":{"label":"Grip seat, Y (the underside a grip's flat top bears on, at the takedown pin's X)","kind":"length","measurements":[{"id":"tdp","value":-1.0695,"unit":"in","pm":0.0115,"source":{"type":"derived","expr":"{std.ar15.deck_y} - {std.ar15.grip_seat_below_deck}","via":"harvest"},"note":"A mil-spec lower: the flat the lug hangs from is the drawing's, 1.318 ±.010 below the deck."},{"id":"left","value":-1.07,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 92d56fedaacf (left side on white: Palmetto State Armory's gallery picture 7a4a7701.jpg, 546 x 546, from the page the user saved 2026-10-12)","scaleRef":"frame from the reviewed holes takedown (425.8, 245.9), pivot (47.0, 246.3) = (0, 0), (6.375, 0): 59.42 px/in; checked at the selector's, trigger's, hammer's, guard's and catch's holes, each within 0.025 in of the Army drawing's place","method":"the line where the body's face ends over the lug (the lug stands 0.25 in behind the face and is darker), read on a 5x crop with a 0.1 in grid in the frame (g-rear.png) from X -0.09 to 1.1; ± is 2 px","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing dimensions it, and the left photo has the body's lower edge over the lug on it within a pixel."}},"grip_shelf_top_x":{"label":"Grip shelf start (the step behind the grip: the lug's rear face), X","kind":"length","measurements":[{"id":"left","value":-0.095,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 92d56fedaacf (left side on white: Palmetto State Armory's gallery picture 7a4a7701.jpg (546 x 546), from the page the user saved 2026-10-12)","scaleRef":"frame from the reviewed holes takedown, pivot (59.4 px/in, rms 0.000 in over 2 points)","method":"x_min in x [-0.2, 0.6] in y [-1.3, -1.1] of the traced outline (tools/trace.py)","via":"user"},"note":"The lug's rear face (an upright edge between Y -1.08 and -1.35)."}],"note":"The lug's rear face as the outline has it; the drawing's is -0.075 (std.ar15.receiver_rear_x + grip_lug_front_from_rear_face - grip_lug_length), which the model uses."},"trigger_opening_top_y":{"label":"Receiver underside above the trigger opening, Y","kind":"length","measurements":[{"id":"left","value":-1.085,"unit":"in","pm":0.026,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 92d56fedaacf (left side on white: Palmetto State Armory's gallery picture 7a4a7701.jpg (546 x 546), from the page the user saved 2026-10-12)","scaleRef":"frame from the reviewed holes takedown, pivot (59.4 px/in, rms 0.000 in over 2 points)","method":"y_min in x [1.95, 2.85] of the traced outline (tools/trace.py)","via":"user"},"note":"The body's lower edge above the trigger guard's opening."}]},"grip_lug_face_angle":{"label":"The grip lug's sloped face, from the vertical","kind":"angle","measurements":[{"id":"tdp","value":60,"unit":"deg","pm":2,"source":{"type":"derived","expr":"{std.ar15.grip_lug_face_angle}","via":"harvest"},"note":"A mil-spec lower: the lug is the drawing's (60° ±2°)."},{"id":"left","value":61.5,"unit":"deg","pm":2,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 92d56fedaacf (left side on white: Palmetto State Armory's gallery picture 7a4a7701.jpg, 546 x 546, from the page the user saved 2026-10-12)","scaleRef":"frame from the reviewed holes takedown (425.8, 245.9), pivot (47.0, 246.3) = (0, 0), (6.375, 0): 59.42 px/in; checked at the selector's, trigger's, hammer's, guard's and catch's holes, each within 0.025 in of the Army drawing's place","method":"the lug's sloped lower edge on the 5x gridded crop (g-rear.png), from (-0.09, -1.39) to (1.00, -1.98): its lean from the vertical over 1.09 in; ± is 2 px at each end","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's; the photo's is within its ±."},"note":"The check that this lower's lug is the drawing's: in a square view of the left side the lug shows whole under the body's edge."},"grip_lug_rear_x":{"label":"The grip lug's rear face (under the takedown pin), X","kind":"length","measurements":[{"id":"tdp","value":-0.075,"unit":"in","pm":0.025,"source":{"type":"derived","expr":"{std.ar15.receiver_rear_x} + {std.ar15.grip_lug_front_from_rear_face} - {std.ar15.grip_lug_length}","via":"harvest"},"note":"A mil-spec lower: the lug ends 2.300 ahead of the rear face and is 1.25 long."},{"id":"left","value":-0.09,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 92d56fedaacf (left side on white: Palmetto State Armory's gallery picture 7a4a7701.jpg, 546 x 546, from the page the user saved 2026-10-12)","scaleRef":"frame from the reviewed holes takedown (425.8, 245.9), pivot (47.0, 246.3) = (0, 0), (6.375, 0): 59.42 px/in; checked at the selector's, trigger's, hammer's, guard's and catch's holes, each within 0.025 in of the Army drawing's place","method":"the lug's rear face on the 5x gridded crop (g-rear.png), between Y -1.07 and -1.39; ± is 2 px","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's; the photo has the face 0.015 behind it, inside its ±."}},"grip_lug_flat_y":{"label":"The grip lug's bottom flat (where its sloped face ends, behind the trigger guard's ears), Y","kind":"length","measurements":[{"id":"tdp","value":-1.9995,"unit":"in","pm":0.0215,"source":{"type":"derived","expr":"{std.ar15.deck_y} - {std.ar15.grip_seat_below_deck} - {std.ar15.grip_lug_depth}","via":"harvest"},"note":"A mil-spec lower: the flat is .93 below the seat."},{"id":"left","value":-1.98,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 92d56fedaacf (left side on white: Palmetto State Armory's gallery picture 7a4a7701.jpg, 546 x 546, from the page the user saved 2026-10-12)","scaleRef":"frame from the reviewed holes takedown (425.8, 245.9), pivot (47.0, 246.3) = (0, 0), (6.375, 0): 59.42 px/in; checked at the selector's, trigger's, hammer's, guard's and catch's holes, each within 0.025 in of the Army drawing's place","method":"the flat at the sloped face's foot on the 5x gridded crop (g-rear.png), X 1.0 to 1.17; ± is 2 px","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's; the photo has the flat 0.02 above it, inside its ±."}},"rear_underside_arc_r":{"label":"The rear underside (behind the grip's lug, under the tower), the radius of its arc on the centre plane","kind":"length","measurements":[{"id":"model","value":0.75,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{std.ar15.rear_underside_arc_r}","via":"harvest"},"note":"The reference CAD model's arc on a mil-spec forging, about the model's centre (std.ar15.rear_underside_arc_center_x, _below_seat)."},{"id":"left","value":0.771,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 92d56fedaacf (left side on white: Palmetto State Armory's gallery picture 7a4a7701.jpg, 546 x 546, from the page the user saved 2026-10-12)","scaleRef":"frame from the reviewed holes takedown (425.8, 245.9), pivot (47.0, 246.3) = (0, 0), (6.375, 0): 59.42 px/in; checked at the selector's, trigger's, hammer's, guard's and catch's holes, each within 0.025 in of the Army drawing's place","method":"the traced outline's five points along the underside from X -0.81 to -0.29 (tools/trace.py), each one's distance from the reference model's centre (-1.0238, -1.2623): 0.776, 0.773, 0.773, 0.774, 0.760; their mean; ± is 2 px","via":"user"}}],"adopt":{"from":"model","reason":"The reference model's; the photo's silhouette runs 0.01 to 0.026 outside it all along, inside its ±."},"note":"The check that this forging's rear underside is the reference model's, which the model draws (std.ar15.rear_underside_*): in a square view the silhouette's lower edge there is the centre plane's line."},"guard_ears_rear_x":{"label":"The trigger guard's rear ears, their rear face (where the grip's lug ends), X","kind":"length","measurements":[{"id":"tdp","value":1.175,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{std.ar15.receiver_rear_x} + {std.ar15.grip_lug_front_from_rear_face}","via":"harvest"},"note":"A mil-spec lower: the lug ends at the ears 2.300 ahead of the rear face."},{"id":"left","value":1.17,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 92d56fedaacf (left side on white: Palmetto State Armory's gallery picture 7a4a7701.jpg, 546 x 546, from the page the user saved 2026-10-12)","scaleRef":"frame from the reviewed holes takedown (425.8, 245.9), pivot (47.0, 246.3) = (0, 0), (6.375, 0): 59.42 px/in; checked at the selector's, trigger's, hammer's, guard's and catch's holes, each within 0.025 in of the Army drawing's place","method":"the ears' rear face on the 5x gridded crop (g-rear.png), from the lug's flat down to the ear's bottom; ± is 2 px","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's; the photo's edge is on it."}},"trigger_guard_front_x":{"label":"Trigger guard front ear hole, X","kind":"length","measurements":[{"id":"tdp","value":3.3425,"unit":"in","pm":0.007,"source":{"type":"derived","expr":"{std.ar15.trigger_guard_front_x}","via":"harvest"},"note":"A mil-spec lower: the hole is the drawing's. It goes into the right ear only, from its spotface: the left photo doesn't show it."}]},"trigger_guard_front_y":{"label":"Trigger guard front ear hole, Y","kind":"length","measurements":[{"id":"tdp","value":-2.18,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{std.ar15.trigger_guard_rear_y}","via":"harvest"},"note":"The drawing's side elevation has the guard's two holes on one centre line, 2.18 below the takedown pin (sheet 1 of 8448608). Not seen on the left photo."}]},"trigger_guard_rear_x":{"label":"Trigger guard rear ear hole, X","kind":"length","measurements":[{"id":"tdp","value":1.4985,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{std.ar15.trigger_guard_rear_x}","via":"harvest"},"note":"A mil-spec lower: the hole is the drawing's."},{"id":"left","value":1.493,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 92d56fedaacf (left side on white: Palmetto State Armory's gallery picture 7a4a7701.jpg, 546 x 546, from the page the user saved 2026-10-12)","scaleRef":"frame from the reviewed holes takedown (425.8, 245.9), pivot (47.0, 246.3) = (0, 0), (6.375, 0): 59.42 px/in; checked at the selector's, trigger's, hammer's, guard's and catch's holes, each within 0.025 in of the Army drawing's place","method":"the centroid of the hole's see-through, weighted by brightness (.cache/b46/psa/holes.py), which is where the receiver's centre plane shows it; ± is 1.5 px (a see-through 8 to 22 px across, part of it hidden by the bore's wall)","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's; the photo has it 0.005 behind."}},"trigger_guard_rear_y":{"label":"Trigger guard rear ear hole, Y","kind":"length","measurements":[{"id":"tdp","value":-2.18,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{std.ar15.trigger_guard_rear_y}","via":"harvest"},"note":"A mil-spec lower: the hole is the drawing's."},{"id":"left","value":-2.168,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 92d56fedaacf (left side on white: Palmetto State Armory's gallery picture 7a4a7701.jpg, 546 x 546, from the page the user saved 2026-10-12)","scaleRef":"frame from the reviewed holes takedown (425.8, 245.9), pivot (47.0, 246.3) = (0, 0), (6.375, 0): 59.42 px/in; checked at the selector's, trigger's, hammer's, guard's and catch's holes, each within 0.025 in of the Army drawing's place","method":"the centroid of the hole's see-through, weighted by brightness (.cache/b46/psa/holes.py), which is where the receiver's centre plane shows it; ± is 1.5 px (a see-through 8 to 22 px across, part of it hidden by the bore's wall)","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's (2.18 below the takedown pin); the photo reads 0.012 high, inside its ±."}},"trigger_pin_x":{"label":"Trigger pin hole centre, X","kind":"length","measurements":[{"id":"tdp","value":1.928,"unit":"in","pm":0.004,"source":{"type":"derived","expr":"{std.ar15.trigger_pin_x}","via":"harvest"},"note":"A mil-spec lower: the hole is the drawing's."},{"id":"left","value":1.916,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 92d56fedaacf (left side on white: Palmetto State Armory's gallery picture 7a4a7701.jpg, 546 x 546, from the page the user saved 2026-10-12)","scaleRef":"frame from the reviewed holes takedown (425.8, 245.9), pivot (47.0, 246.3) = (0, 0), (6.375, 0): 59.42 px/in; checked at the selector's, trigger's, hammer's, guard's and catch's holes, each within 0.025 in of the Army drawing's place","method":"the centroid of the hole's see-through, weighted by brightness (.cache/b46/psa/holes.py), which is where the receiver's centre plane shows it; ± is 1.5 px (a see-through 8 to 22 px across, part of it hidden by the bore's wall)","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's; the photo has it 0.012 behind, inside its ±."}},"trigger_pin_y":{"label":"Trigger pin hole centre, Y","kind":"length","measurements":[{"id":"tdp","value":-0.689,"unit":"in","pm":0.0035,"source":{"type":"derived","expr":"{std.ar15.trigger_pin_y}","via":"harvest"},"note":"A mil-spec lower: the hole is the drawing's."},{"id":"left","value":-0.688,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 92d56fedaacf (left side on white: Palmetto State Armory's gallery picture 7a4a7701.jpg, 546 x 546, from the page the user saved 2026-10-12)","scaleRef":"frame from the reviewed holes takedown (425.8, 245.9), pivot (47.0, 246.3) = (0, 0), (6.375, 0): 59.42 px/in; checked at the selector's, trigger's, hammer's, guard's and catch's holes, each within 0.025 in of the Army drawing's place","method":"the centroid of the hole's see-through, weighted by brightness (.cache/b46/psa/holes.py), which is where the receiver's centre plane shows it; ± is 1.5 px (a see-through 8 to 22 px across, part of it hidden by the bore's wall)","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's; the photo has it on it."}},"hammer_pin_x":{"label":"Hammer pin hole centre, X","kind":"length","measurements":[{"id":"tdp","value":2.771,"unit":"in","pm":0.004,"source":{"type":"derived","expr":"{std.ar15.hammer_pin_x}","via":"harvest"},"note":"A mil-spec lower: the hole is the drawing's."},{"id":"left","value":2.747,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 92d56fedaacf (left side on white: Palmetto State Armory's gallery picture 7a4a7701.jpg, 546 x 546, from the page the user saved 2026-10-12)","scaleRef":"frame from the reviewed holes takedown (425.8, 245.9), pivot (47.0, 246.3) = (0, 0), (6.375, 0): 59.42 px/in; checked at the selector's, trigger's, hammer's, guard's and catch's holes, each within 0.025 in of the Army drawing's place","method":"the centroid of the hole's see-through, weighted by brightness (.cache/b46/psa/holes.py), which is where the receiver's centre plane shows it; ± is 1.5 px (a see-through 8 to 22 px across, part of it hidden by the bore's wall)","via":"user"}},{"id":"detail","value":2.775,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 07c1333b3b96 (the left side round the selector's hole, close: Palmetto State Armory's gallery picture 7a4a7703.jpg, 546 x 546, from the page the user saved 2026-10-12)","scaleRef":"frame from the near rims of the selector's and the trigger's holes at the Army drawing's places (std.ar15.selector_x/_y, trigger_pin_x/_y): 187.85 px/in, turned 0.09 degrees; each rim a circle fitted to where the hole gives way to the face (.cache/b46/psa/detail_frame.py; rms 0.5 to 1.2 px)","method":"the hole's near rim, a circle fitted to its edge (px 36.81, 232.91), in the frame the other two holes set: an independent reading of where the hammer's hole is from the trigger's and the selector's; ± is 1.5 px","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's. The close-up, framed by the selector's and trigger's holes, has the hammer's 0.004 ahead of it; the whole view's see-through (8 px across) reads 0.024 behind, inside its ±: the worst of the five holes the frame was checked at."}},"hammer_pin_y":{"label":"Hammer pin hole centre, Y","kind":"length","measurements":[{"id":"tdp","value":-0.375,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{std.ar15.hammer_pin_y}","via":"harvest"},"note":"A mil-spec lower: the hole is the drawing's."},{"id":"left","value":-0.383,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 92d56fedaacf (left side on white: Palmetto State Armory's gallery picture 7a4a7701.jpg, 546 x 546, from the page the user saved 2026-10-12)","scaleRef":"frame from the reviewed holes takedown (425.8, 245.9), pivot (47.0, 246.3) = (0, 0), (6.375, 0): 59.42 px/in; checked at the selector's, trigger's, hammer's, guard's and catch's holes, each within 0.025 in of the Army drawing's place","method":"the centroid of the hole's see-through, weighted by brightness (.cache/b46/psa/holes.py), which is where the receiver's centre plane shows it; ± is 1.5 px (a see-through 8 to 22 px across, part of it hidden by the bore's wall)","via":"user"}},{"id":"detail","value":-0.377,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 07c1333b3b96 (the left side round the selector's hole, close: Palmetto State Armory's gallery picture 7a4a7703.jpg, 546 x 546, from the page the user saved 2026-10-12)","scaleRef":"frame from the near rims of the selector's and the trigger's holes at the Army drawing's places (std.ar15.selector_x/_y, trigger_pin_x/_y): 187.85 px/in, turned 0.09 degrees; each rim a circle fitted to where the hole gives way to the face (.cache/b46/psa/detail_frame.py; rms 0.5 to 1.2 px)","method":"the hole's near rim, a circle fitted to its edge (px 36.81, 232.91), in the frame the other two holes set; ± is 1.5 px","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's; the close-up has it 0.002 low, the whole view 0.008 low."}},"selector_x":{"label":"Safety selector hole centre, X","kind":"length","measurements":[{"id":"tdp","value":0.803,"unit":"in","pm":0.004,"source":{"type":"derived","expr":"{std.ar15.selector_x}","via":"harvest"},"note":"A mil-spec lower: the hole is the drawing's."},{"id":"left","value":0.799,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 92d56fedaacf (left side on white: Palmetto State Armory's gallery picture 7a4a7701.jpg, 546 x 546, from the page the user saved 2026-10-12)","scaleRef":"frame from the reviewed holes takedown (425.8, 245.9), pivot (47.0, 246.3) = (0, 0), (6.375, 0): 59.42 px/in; checked at the selector's, trigger's, hammer's, guard's and catch's holes, each within 0.025 in of the Army drawing's place","method":"the centroid of the hole's see-through, weighted by brightness (.cache/b46/psa/holes.py), which is where the receiver's centre plane shows it; ± is 1.5 px (a see-through 8 to 22 px across, part of it hidden by the bore's wall)","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's; the photo has it 0.004 behind."}},"selector_y":{"label":"Safety selector hole centre, Y","kind":"length","measurements":[{"id":"std","value":-0.466,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{std.ar15.selector_y}","via":"harvest"},"note":"The standard's (read on the Workhorse's two photos: the drawing's chain for it isn't tied to the pin line on the scan)."},{"id":"left","value":-0.467,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 92d56fedaacf (left side on white: Palmetto State Armory's gallery picture 7a4a7701.jpg, 546 x 546, from the page the user saved 2026-10-12)","scaleRef":"frame from the reviewed holes takedown (425.8, 245.9), pivot (47.0, 246.3) = (0, 0), (6.375, 0): 59.42 px/in; checked at the selector's, trigger's, hammer's, guard's and catch's holes, each within 0.025 in of the Army drawing's place","method":"the centroid of the hole's see-through, weighted by brightness (.cache/b46/psa/holes.py), which is where the receiver's centre plane shows it; ± is 1.5 px (a see-through 8 to 22 px across, part of it hidden by the bore's wall)","via":"user"}}],"adopt":{"from":"std","reason":"The standard's; the photo has it on it."}},"fcg_pin_hole_d":{"label":"Hammer and trigger pin holes, diameter","kind":"length","measurements":[{"id":"tdp","value":0.15675,"unit":"in","pm":0.00075,"source":{"type":"derived","expr":"{std.ar15.fcg_pin_hole_d}","via":"harvest"},"note":"A mil-spec lower: the drawing's holes for the .154 pins. The page says only: 'These forged lowers are quality made by a mil-spec contractor'."},{"id":"detail-hammer","value":0.159,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 07c1333b3b96 (the left side round the selector's hole, close: Palmetto State Armory's gallery picture 7a4a7703.jpg, 546 x 546, from the page the user saved 2026-10-12)","scaleRef":"frame from the near rims of the selector's and the trigger's holes at the Army drawing's places (std.ar15.selector_x/_y, trigger_pin_x/_y): 187.85 px/in, turned 0.09 degrees; each rim a circle fitted to where the hole gives way to the face (.cache/b46/psa/detail_frame.py; rms 0.5 to 1.2 px)","method":"the hammer hole's near rim, a circle fitted to its edge: 14.91 px radius; ± is 0.75 px each side","via":"user"}},{"id":"detail-trigger","value":0.151,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 07c1333b3b96 (the left side round the selector's hole, close: Palmetto State Armory's gallery picture 7a4a7703.jpg, 546 x 546, from the page the user saved 2026-10-12)","scaleRef":"frame from the near rims of the selector's and the trigger's holes at the Army drawing's places (std.ar15.selector_x/_y, trigger_pin_x/_y): 187.85 px/in, turned 0.09 degrees; each rim a circle fitted to where the hole gives way to the face (.cache/b46/psa/detail_frame.py; rms 0.5 to 1.2 px)","method":"the trigger hole's near rim, a circle fitted to its edge: 14.14 px radius (rms 1.2 px: part of its rim is a see-through's bright crescent); ± is 1.2 px each side","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's. The close-up has the two rims 0.159 and 0.151 across: either side of the drawing's .157, and 0.011 to 0.02 under a large pin's .170."},"note":"The page doesn't state the pins' size. The close-up has the two holes' rims at the small pin's size, not a .170 pin's: the same fit has the selector's rim 0.382 across for the drawing's .376."},"rear_behind_pin":{"label":"Rear face (the buffer tower's, where the end plate bears) behind the takedown pin","kind":"length","measurements":[{"id":"std","value":1.125,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"-{std.ar15.receiver_rear_x}","via":"harvest"},"note":"A mil-spec lower: the rear face is the drawing's (7.503 -.006 behind the pivot pin). The left photo's silhouette is 0.03 to 0.06 behind it (rear_face_x): the ring's near side, 0.7 in nearer the lens than the centre plane and 3.7 in from the picture's middle."}]},"rear_face_x":{"label":"Receiver rear silhouette below the tower ring, X","kind":"length","measurements":[{"id":"left","value":-1.19,"unit":"in","pm":0.026,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 92d56fedaacf (left side on white: Palmetto State Armory's gallery picture 7a4a7701.jpg (546 x 546), from the page the user saved 2026-10-12)","scaleRef":"frame from the reviewed holes takedown, pivot (59.4 px/in, rms 0.000 in over 2 points)","method":"x_min in y [-0.4, 0.0] of the traced outline (tools/trace.py)","via":"user"},"note":"The rear silhouette below the tower's ring: the ring's near side, seen from ahead; the drawing's rear face is -1.125 (std.ar15.receiver_rear_x)."}],"note":"The silhouette's rear edge under the ring. Not the rear face: the ring is 1.392 across and is seen from ahead, so its near side shows behind the face by its distance from the centre plane times the lens's angle there. The face is the drawing's (rear_behind_pin)."},"tower_top_above_pin":{"label":"Top of the buffer-tower ring above the pin line","kind":"length","measurements":[{"id":"std","value":1.5735,"unit":"in","pm":0.0065,"source":{"type":"derived","expr":"{std.ar15.buffer_tower_top_y}","via":"harvest"},"note":"A mil-spec lower: the ring's top is the drawing's (1.325 above the deck). The left photo's silhouette tops out higher, as a ring seen from below its own top's level does (the outline's y_max, in the profile's method)."}]},"tower_front_x":{"label":"Buffer-tower front edge (the side walls' sweep up to the ring), X","kind":"length","measurements":[{"id":"left","value":-0.416,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 92d56fedaacf (left side on white: Palmetto State Armory's gallery picture 7a4a7701.jpg (546 x 546), from the page the user saved 2026-10-12)","scaleRef":"frame from the reviewed holes takedown, pivot (59.4 px/in, rms 0.000 in over 2 points)","method":"x_max in x [-1.5, 3.0] in y [0.5, 1.4] of the traced outline (tools/trace.py)","via":"user"},"note":"Front edge of the walls' sweep up to the ring, above the deck."}],"note":"The outline's front edge above the deck between Y 0.5 and 1.4. The lens stands ahead of the tower (the picture's middle is 2.6 in ahead of the takedown pin), so what is furthest forward there may be the far wall or the ring's inside seen through its front, not the near wall's own edge (CLAUDE.md, 2026-10-12: the Workhorse's). The ring's front face is the drawing's (std.ar15.buffer_tower_front_x) and the walls rise to it along the drawing's arc (std.ar15.rear_wall_arc_r): this figure is only how far forward the model's tower block is taken from the outline before that arc is cut."},"deck_above_pin":{"label":"Receiver top deck above the pin line","kind":"length","measurements":[{"id":"left","value":0.261,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 92d56fedaacf (left side on white: Palmetto State Armory's gallery picture 7a4a7701.jpg (546 x 546), from the page the user saved 2026-10-12)","scaleRef":"frame from the reviewed holes takedown, pivot (59.4 px/in, rms 0.000 in over 2 points)","method":"top (tooth tops: the edge's max over 0.05 in windows) along x [0.6, 5.8] of the traced outline (tools/trace.py)","via":"user"},"note":"The top edge between the tower and the pivot lug: the drawing's deck is 0.2485 (std.ar15.deck_y)."}],"note":"std.ar15.deck_y is 0.2485 (.250 -.003): the outline's top between the tower and the pivot lug is a reading of that plane, and the model's deck is the plane itself (lib.deck_outline)."},"front_ahead_of_pin":{"label":"Front of the pivot-pin lug ahead of the takedown pin","kind":"length","measurements":[{"id":"left","value":6.602,"unit":"in","pm":0.036,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 92d56fedaacf (left side on white: Palmetto State Armory's gallery picture 7a4a7701.jpg (546 x 546), from the page the user saved 2026-10-12)","scaleRef":"frame from the reviewed holes takedown, pivot (59.4 px/in, rms 0.000 in over 2 points)","method":"x_max of the traced outline (tools/trace.py)","via":"user"},"note":"Front of the pivot-pin lug."}]},"bottom_below_pin":{"label":"Lowest point below the pin line (the trigger guard's ears)","kind":"length","measurements":[{"id":"left","value":2.329,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 92d56fedaacf (left side on white: Palmetto State Armory's gallery picture 7a4a7701.jpg (546 x 546), from the page the user saved 2026-10-12)","scaleRef":"frame from the reviewed holes takedown, pivot (59.4 px/in, rms 0.000 in over 2 points)","method":"−y_min of the traced outline (tools/trace.py)","via":"user"},"note":"Lowest point: the trigger guard's front ear, at the well's rear (the rear ear's bottom is within a pixel of it)."}]},"magwell_front_x":{"label":"Magwell front face, X","kind":"length","measurements":[{"id":"left","value":6.148,"unit":"in","pm":0.035,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 92d56fedaacf (left side on white: Palmetto State Armory's gallery picture 7a4a7701.jpg (546 x 546), from the page the user saved 2026-10-12)","scaleRef":"frame from the reviewed holes takedown, pivot (59.4 px/in, rms 0.000 in over 2 points)","method":"x_max in x [3.0, 7.0] in y [-1.5, -0.6] of the traced outline (tools/trace.py)","via":"user"},"note":"Front face of the magazine well (the near wall's)."}],"note":"The silhouette's front edge below the pivot lug: the well's near wall, 0.11 in nearer the lens than the body's face and 3.5 in from the picture's middle, so it reads about a hundredth ahead of where it is."},"magwell_wall_rear_x_left":{"label":"Magazine well's outside walls, rear edge, X (left side)","kind":"length","measurements":[{"id":"left","value":3.49,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 92d56fedaacf (left side on white: Palmetto State Armory's gallery picture 7a4a7701.jpg, 546 x 546, from the page the user saved 2026-10-12)","scaleRef":"frame from the reviewed holes takedown (425.8, 245.9), pivot (47.0, 246.3) = (0, 0), (6.375, 0): 59.42 px/in; checked at the selector's, trigger's, hammer's, guard's and catch's holes, each within 0.025 in of the Army drawing's place","method":"the step's edge read on a 9x crop with a 0.1 in grid in the frame (.cache/b46/psa/fgrid.py, g-catch.png); ± is 2 px, between Y -1.15 and -1.6","via":"user"}}],"note":"On the left the wall's rear edge is the step ahead of the trigger guard's front ear; above Y -1.1 it curves back toward the bolt catch's bosses (magwell_wall_upper_rear_x_left). The Workhorse's is 3.455, Bear Creek's 3.48: one forging pattern."},"magwell_wall_upper_rear_x_left":{"label":"Magazine well's outside walls, rear edge above the step's curve, X (left side)","kind":"length","measurements":[{"id":"left","value":2.955,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 92d56fedaacf (left side on white: Palmetto State Armory's gallery picture 7a4a7701.jpg, 546 x 546, from the page the user saved 2026-10-12)","scaleRef":"frame from the reviewed holes takedown (425.8, 245.9), pivot (47.0, 246.3) = (0, 0), (6.375, 0): 59.42 px/in; checked at the selector's, trigger's, hammer's, guard's and catch's holes, each within 0.025 in of the Army drawing's place","method":"the step's dark line read on a 9x crop with a 0.1 in grid in the frame (.cache/b46/psa/fgrid.py, g-catch.png); ± is 2 px: straight from the deck down to Y -0.6","via":"user"}}],"note":"The Workhorse's is 2.948, Bear Creek's 2.96."},"magwell_wall_curve_top_y_left":{"label":"Magazine well's outside walls, left side, where the rear edge starts to curve forward, Y","kind":"length","measurements":[{"id":"left","value":-0.62,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 92d56fedaacf (left side on white: Palmetto State Armory's gallery picture 7a4a7701.jpg, 546 x 546, from the page the user saved 2026-10-12)","scaleRef":"frame from the reviewed holes takedown (425.8, 245.9), pivot (47.0, 246.3) = (0, 0), (6.375, 0): 59.42 px/in; checked at the selector's, trigger's, hammer's, guard's and catch's holes, each within 0.025 in of the Army drawing's place","method":"the step's dark line read on a 9x crop with a 0.1 in grid in the frame (.cache/b46/psa/fgrid.py, g-catch.png); ± is 2 px: straight to -0.62, then forward: X 3.05 at -0.75, 3.2 at -0.88, 3.4 at -1.0","via":"user"}}]},"magwell_wall_curve_bottom_y_left":{"label":"Magazine well's outside walls, left side, where the rear edge's curve meets the step, Y","kind":"length","measurements":[{"id":"left","value":-1.09,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 92d56fedaacf (left side on white: Palmetto State Armory's gallery picture 7a4a7701.jpg, 546 x 546, from the page the user saved 2026-10-12)","scaleRef":"frame from the reviewed holes takedown (425.8, 245.9), pivot (47.0, 246.3) = (0, 0), (6.375, 0): 59.42 px/in; checked at the selector's, trigger's, hammer's, guard's and catch's holes, each within 0.025 in of the Army drawing's place","method":"the step's dark line read on a 9x crop with a 0.1 in grid in the frame (.cache/b46/psa/fgrid.py, g-catch.png); ± is 2 px: X 3.47 by Y -1.05, upright from -1.09 down","via":"user"}}],"note":"Between the two ends the edge is drawn as a smooth S (3t^2 - 2t^3), as the catalog's other forged lowers' is."},"bolt_catch_boss_rear_x":{"label":"Bolt catch bosses: the rear boss's rear edge, X (left side)","kind":"length","measurements":[{"id":"left","value":3.04,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 92d56fedaacf (left side on white: Palmetto State Armory's gallery picture 7a4a7701.jpg, 546 x 546, from the page the user saved 2026-10-12)","scaleRef":"frame from the reviewed holes takedown (425.8, 245.9), pivot (47.0, 246.3) = (0, 0), (6.375, 0): 59.42 px/in; checked at the selector's, trigger's, hammer's, guard's and catch's holes, each within 0.025 in of the Army drawing's place","method":"the pad's edge read on a 9x crop with a 0.1 in grid in the frame (.cache/b46/psa/fgrid.py, g-catch.png); ± is 2 px","via":"user"}}],"note":"The Workhorse's is 3.013, Bear Creek's 3.05."},"bolt_catch_gap_rear_x":{"label":"Bolt catch bosses: the gap between them (where the catch sits), rear edge, X","kind":"length","measurements":[{"id":"tdp","value":3.203,"unit":"in","pm":0.007,"source":{"type":"derived","expr":"{std.ar15.bolt_catch_slot_front_x} - {std.ar15.bolt_catch_slot_width}","via":"harvest"},"note":"The gap is the drawing's slot for the catch, at the left face."},{"id":"left","value":3.21,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 92d56fedaacf (left side on white: Palmetto State Armory's gallery picture 7a4a7701.jpg, 546 x 546, from the page the user saved 2026-10-12)","scaleRef":"frame from the reviewed holes takedown (425.8, 245.9), pivot (47.0, 246.3) = (0, 0), (6.375, 0): 59.42 px/in; checked at the selector's, trigger's, hammer's, guard's and catch's holes, each within 0.025 in of the Army drawing's place","method":"the gap's dark edge read on a 9x crop with a 0.1 in grid in the frame (.cache/b46/psa/fgrid.py, g-catch.png); ± is 2 px","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's slot; the photo's edge is on it."}},"bolt_catch_gap_front_x":{"label":"Bolt catch bosses: the gap's front edge, X","kind":"length","measurements":[{"id":"tdp","value":3.375,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.ar15.bolt_catch_slot_front_x}","via":"harvest"},"note":"The gap is the drawing's slot for the catch, at the left face."},{"id":"left","value":3.39,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 92d56fedaacf (left side on white: Palmetto State Armory's gallery picture 7a4a7701.jpg, 546 x 546, from the page the user saved 2026-10-12)","scaleRef":"frame from the reviewed holes takedown (425.8, 245.9), pivot (47.0, 246.3) = (0, 0), (6.375, 0): 59.42 px/in; checked at the selector's, trigger's, hammer's, guard's and catch's holes, each within 0.025 in of the Army drawing's place","method":"the gap's dark edge read on a 9x crop with a 0.1 in grid in the frame (.cache/b46/psa/fgrid.py, g-catch.png); ± is 2 px","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's slot; the photo's edge is 0.015 ahead of it, inside its ±."}},"bolt_catch_boss_front_x":{"label":"Bolt catch bosses: the front boss's front edge, X","kind":"length","measurements":[{"id":"left","value":3.6,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 92d56fedaacf (left side on white: Palmetto State Armory's gallery picture 7a4a7701.jpg, 546 x 546, from the page the user saved 2026-10-12)","scaleRef":"frame from the reviewed holes takedown (425.8, 245.9), pivot (47.0, 246.3) = (0, 0), (6.375, 0): 59.42 px/in; checked at the selector's, trigger's, hammer's, guard's and catch's holes, each within 0.025 in of the Army drawing's place","method":"the pad's edge read on a 9x crop with a 0.1 in grid in the frame (.cache/b46/psa/fgrid.py, g-catch.png); ± is 2 px","via":"user"}}],"note":"The Workhorse's is 3.576, Bear Creek's 3.58."},"bolt_catch_boss_bottom_y":{"label":"Bolt catch bosses: their bottom edges, Y (they rise to the deck)","kind":"length","measurements":[{"id":"left","value":-0.11,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 92d56fedaacf (left side on white: Palmetto State Armory's gallery picture 7a4a7701.jpg, 546 x 546, from the page the user saved 2026-10-12)","scaleRef":"frame from the reviewed holes takedown (425.8, 245.9), pivot (47.0, 246.3) = (0, 0), (6.375, 0): 59.42 px/in; checked at the selector's, trigger's, hammer's, guard's and catch's holes, each within 0.025 in of the Army drawing's place","method":"the pads' lower edges read on a 9x crop with a 0.1 in grid in the frame (.cache/b46/psa/fgrid.py, g-catch.png); ± is 2 px; the bosses' face stands 0.07 nearer the lens than the wall they are on","via":"user"}}],"note":"The Workhorse's is -0.05, Bear Creek's -0.14."},"band_rear_x":{"label":"The raised band down the well's left wall, its rear edge, X","kind":"length","measurements":[{"id":"model","value":3.975,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{std.ar15.magwell_band_rear_x}","via":"harvest"},"note":"The reference CAD model's band on a mil-spec forging (std.ar15.magwell_band_*), which the model draws."},{"id":"left","value":3.98,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 92d56fedaacf (left side on white: Palmetto State Armory's gallery picture 7a4a7701.jpg, 546 x 546, from the page the user saved 2026-10-12)","scaleRef":"frame from the reviewed holes takedown (425.8, 245.9), pivot (47.0, 246.3) = (0, 0), (6.375, 0): 59.42 px/in; checked at the selector's, trigger's, hammer's, guard's and catch's holes, each within 0.025 in of the Army drawing's place","method":"the band's rear shadow line read on a 9x crop with a 0.1 in grid in the frame (.cache/b46/psa/fgrid.py, g-catch.png); ± is 2 px and on g-front.png, from the deck to the lip","via":"user"}}],"adopt":{"from":"model","reason":"The reference model's; the photo's line is on it."},"note":"A check that this forging has the standard's band where the standard has it."},"band_front_x":{"label":"The raised band down the well's left wall, its front edge, X","kind":"length","measurements":[{"id":"model","value":4.549,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{std.ar15.magwell_band_front_x}","via":"harvest"},"note":"The reference CAD model's band on a mil-spec forging."},{"id":"left","value":4.57,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/psa-stealth-stripped-lower 92d56fedaacf (left side on white: Palmetto State Armory's gallery picture 7a4a7701.jpg, 546 x 546, from the page the user saved 2026-10-12)","scaleRef":"frame from the reviewed holes takedown (425.8, 245.9), pivot (47.0, 246.3) = (0, 0), (6.375, 0): 59.42 px/in; checked at the selector's, trigger's, hammer's, guard's and catch's holes, each within 0.025 in of the Army drawing's place","method":"the first of two light lines 0.05 apart on a 6x crop with a 0.1 in grid (g-front.png), from the deck to the lip: at 4.57; the second, at 4.62, is the foot of the band's slope (the model's: 4.549 + std.ar15.magwell_band_side, 4.633); ± is 2 px","via":"user"}}],"adopt":{"from":"model","reason":"The reference model's; the photo's line is 0.02 ahead of it, inside its ±, and the slope's foot is where the model's is."}},"fence_rear_x":{"label":"The magazine catch's fence, its flat face's rear edge, X","kind":"length","measurements":[{"id":"workhorse","value":3.02,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{bad-workhorse-lower.fence_rear_x}","via":"harvest"},"note":"NOT SEEN ON THIS LOWER: no photo of its right side is on file (the saved page's two pictures are both of the left). The catalog's forged mil-spec lower's reading (the Workhorse's, on its own pin-framed right photo), which the reference CAD model's mil-spec forging and Bear Creek's lower have within a few hundredths: Palmetto State Armory: 'These forged lowers are quality made by a mil-spec contractor using 7075-T6 aluminum' (the page as the user saved it, 2026-10-12). The ± is widened to what the three differ by."}]},"fence_front_x":{"label":"The magazine catch's fence, its flat face's front edge, X","kind":"length","measurements":[{"id":"workhorse","value":3.565,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{bad-workhorse-lower.fence_front_x}","via":"harvest"},"note":"NOT SEEN ON THIS LOWER: no photo of its right side is on file (the saved page's two pictures are both of the left). The catalog's forged mil-spec lower's reading (the Workhorse's, on its own pin-framed right photo), which the reference CAD model's mil-spec forging and Bear Creek's lower have within a few hundredths: Palmetto State Armory: 'These forged lowers are quality made by a mil-spec contractor using 7075-T6 aluminum' (the page as the user saved it, 2026-10-12). The ± is widened to what the three differ by."}]},"fence_top_y":{"label":"The magazine catch's fence, its flat face's top edge, Y","kind":"length","measurements":[{"id":"workhorse","value":-0.22,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{bad-workhorse-lower.fence_top_y}","via":"harvest"},"note":"NOT SEEN ON THIS LOWER: no photo of its right side is on file (the saved page's two pictures are both of the left). The catalog's forged mil-spec lower's reading (the Workhorse's, on its own pin-framed right photo), which the reference CAD model's mil-spec forging and Bear Creek's lower have within a few hundredths: Palmetto State Armory: 'These forged lowers are quality made by a mil-spec contractor using 7075-T6 aluminum' (the page as the user saved it, 2026-10-12). The ± is widened to what the three differ by."}]},"fence_bottom_y":{"label":"The magazine catch's fence, its flat face's bottom edge, Y","kind":"length","measurements":[{"id":"workhorse","value":-0.91,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{bad-workhorse-lower.fence_bottom_y}","via":"harvest"},"note":"NOT SEEN ON THIS LOWER: no photo of its right side is on file (the saved page's two pictures are both of the left). The catalog's forged mil-spec lower's reading (the Workhorse's, on its own pin-framed right photo), which the reference CAD model's mil-spec forging and Bear Creek's lower have within a few hundredths: Palmetto State Armory: 'These forged lowers are quality made by a mil-spec contractor using 7075-T6 aluminum' (the page as the user saved it, 2026-10-12). The ± is widened to what the three differ by."}]},"fence_corner_r":{"label":"The magazine catch's fence, its flat face's corners, radius","kind":"length","measurements":[{"id":"workhorse","value":0.1,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{bad-workhorse-lower.fence_corner_r}","via":"harvest"},"note":"NOT SEEN ON THIS LOWER: no photo of its right side is on file (the saved page's two pictures are both of the left). The catalog's forged mil-spec lower's reading (the Workhorse's, on its own pin-framed right photo), which the reference CAD model's mil-spec forging and Bear Creek's lower have within a few hundredths: Palmetto State Armory: 'These forged lowers are quality made by a mil-spec contractor using 7075-T6 aluminum' (the page as the user saved it, 2026-10-12). The ± is widened to what the three differ by."}]},"magwell_wall_rear_x":{"label":"Magazine well's outside walls, rear edge, X (right side)","kind":"length","measurements":[{"id":"workhorse","value":3.619,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{bad-workhorse-lower.magwell_wall_rear_x}","via":"harvest"},"note":"NOT SEEN ON THIS LOWER: no photo of its right side is on file (the saved page's two pictures are both of the left). The catalog's forged mil-spec lower's reading (the Workhorse's, on its own pin-framed right photo), which the reference CAD model's mil-spec forging and Bear Creek's lower have within a few hundredths: Palmetto State Armory: 'These forged lowers are quality made by a mil-spec contractor using 7075-T6 aluminum' (the page as the user saved it, 2026-10-12). The ± is widened to what the three differ by."}]},"well_roll_crest_out":{"label":"The roll along the top of the magazine well's right wall, its crest from the centre plane (Z)","kind":"length","measurements":[{"id":"workhorse","value":0.8,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{bad-workhorse-lower.well_roll_crest_out}","via":"harvest"},"note":"NOT SEEN ON THIS LOWER: no photo of its right side is on file (the saved page's two pictures are both of the left). The catalog's forged mil-spec lower's reading (the Workhorse's, on its own pin-framed right photo), which the reference CAD model's mil-spec forging and Bear Creek's lower have within a few hundredths: Palmetto State Armory: 'These forged lowers are quality made by a mil-spec contractor using 7075-T6 aluminum' (the page as the user saved it, 2026-10-12). The ± is widened to what the three differ by."}]},"well_roll_bottom_y":{"label":"The roll along the top of the well's right wall, its lower edge, Y","kind":"length","measurements":[{"id":"workhorse","value":-0.204,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{bad-workhorse-lower.well_roll_bottom_y}","via":"harvest"},"note":"NOT SEEN ON THIS LOWER: no photo of its right side is on file (the saved page's two pictures are both of the left). The catalog's forged mil-spec lower's reading (the Workhorse's, on its own pin-framed right photo), which the reference CAD model's mil-spec forging and Bear Creek's lower have within a few hundredths: Palmetto State Armory: 'These forged lowers are quality made by a mil-spec contractor using 7075-T6 aluminum' (the page as the user saved it, 2026-10-12). The ± is widened to what the three differ by."}]},"well_roll_rear_x":{"label":"The roll along the top of the well's right wall, its rear end, X","kind":"length","measurements":[{"id":"workhorse","value":2.905,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{bad-workhorse-lower.well_roll_rear_x}","via":"harvest"},"note":"NOT SEEN ON THIS LOWER: no photo of its right side is on file (the saved page's two pictures are both of the left). The catalog's forged mil-spec lower's reading (the Workhorse's, on its own pin-framed right photo), which the reference CAD model's mil-spec forging and Bear Creek's lower have within a few hundredths: Palmetto State Armory: 'These forged lowers are quality made by a mil-spec contractor using 7075-T6 aluminum' (the page as the user saved it, 2026-10-12). The ± is widened to what the three differ by."}]},"well_roll_rear_round":{"label":"The roll along the top of the well's right wall, how far its rounded rear end runs before the roll is full","kind":"length","measurements":[{"id":"workhorse","value":0.19,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{bad-workhorse-lower.well_roll_rear_round}","via":"harvest"},"note":"NOT SEEN ON THIS LOWER: no photo of its right side is on file (the saved page's two pictures are both of the left). The catalog's forged mil-spec lower's reading (the Workhorse's, on its own pin-framed right photo), which the reference CAD model's mil-spec forging and Bear Creek's lower have within a few hundredths: Palmetto State Armory: 'These forged lowers are quality made by a mil-spec contractor using 7075-T6 aluminum' (the page as the user saved it, 2026-10-12). The ± is widened to what the three differ by."}]},"well_roll_front_x":{"label":"The roll along the top of the well's right wall, its front end (a flat face beside the pivot lug), X","kind":"length","measurements":[{"id":"workhorse","value":6.231,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{bad-workhorse-lower.well_roll_front_x}","via":"harvest"},"note":"NOT SEEN ON THIS LOWER: no photo of its right side is on file (the saved page's two pictures are both of the left). The catalog's forged mil-spec lower's reading (the Workhorse's, on its own pin-framed right photo), which the reference CAD model's mil-spec forging and Bear Creek's lower have within a few hundredths: Palmetto State Armory: 'These forged lowers are quality made by a mil-spec contractor using 7075-T6 aluminum' (the page as the user saved it, 2026-10-12). The ± is widened to what the three differ by."}]}}},{"subject":"psa-stripped-upper","title":"Palmetto State Armory AR-15 Stripped Upper Receiver (51655109407)","dimensions":{"weight":{"label":"Weight (the stripped receiver: no port door, forward assist or barrel)","kind":"mass","measurements":[],"note":"No page states one: Palmetto State Armory's page for it, saved by the user on 2026-10-12, has no weight row and none in its text (Manufacturer, Platform, Material, Finish), and no other source is on file (the maker's site refuses the reader, D59; no seller's page for it has been harvested). Not estimated: a build with it says its total is unknown (D61)."},"bore_axis_above_pin":{"label":"Bore axis above the takedown pin centre","kind":"length","measurements":[{"id":"standard","value":0.8775,"unit":"in","pm":0.0015,"source":{"type":"derived","expr":"{std.ar15.bore_axis_y}","via":"harvest"},"note":"The standard's. Palmetto State Armory's page: \"Forged 7075-T6 A3 AR upper is hard coat anodized black for durability. Featuring M4 feedramp cuts and no T marks.\" It names no standard; its being the Army drawing's receiver is what \"A3 AR upper\" is taken to say, and each face is tried on its photo."},{"id":"right","value":0.876,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/psa-stripped-upper 55761f177232 (Palmetto State Armory's product photo 51655109407.jpg, in the page the user saved on 2026-10-12: the stripped receiver's right side on white, 546 x 546)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each see-through opening fitted as its near rim's circle and its far rim's at once (.cache/b46/psa-stripped-upper/lens.py: rims found to 0.05 px), their midpoints the frame's points: 62.96 px/in on the receiver's mid-plane, a pixel 0.016 in; the rail's 13 slots, read at the teeth's near edges, run 1.5% over the standard pitch on it, as a lens some 26 in away makes them","method":"the threaded nose's top and bottom edges over x 6.75 to 6.95 read 1.480 and 0.256 from the pin line (its silhouette's edges lie within a hundredth of the mid-plane from a lens 0.5 below its axis): their middle 0.868, and at that end the picture is 0.94% smaller than between the holes (the receiver's rear end is nearer the lens: the tooth tops stand 2.136 over the takedown hole and 2.099 over the pivot's): 0.876; ± is a pixel","via":"user"}}],"adopt":{"from":"standard","reason":"The drawings' figure; this receiver's own photo puts its nose's axis within its ± of it."}},"rail_top_above_pin":{"label":"The top rail's surface above the pin line","kind":"length","measurements":[{"id":"right","value":2.09,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/psa-stripped-upper 55761f177232 (Palmetto State Armory's product photo 51655109407.jpg, in the page the user saved on 2026-10-12: the stripped receiver's right side on white, 546 x 546)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each see-through opening fitted as its near rim's circle and its far rim's at once (.cache/b46/psa-stripped-upper/lens.py: rims found to 0.05 px), their midpoints the frame's points: 62.96 px/in on the receiver's mid-plane, a pixel 0.016 in; the rail's 13 slots, read at the teeth's near edges, run 1.5% over the standard pitch on it, as a lens some 26 in away makes them","method":"the tooth tops read 2.117 at mid-length (2.136 over the takedown hole, 2.099 over the pivot's: the receiver's rear end is nearer the lens); the silhouette's top is the rail's near upper edge, 0.36 nearer than the mid-plane and 1.8 above where the lens stands: the lens stands about 22 in away opposite x 2.58, y 0.33 (right_photo_lens_*), so what is z nearer than the mid-plane reads large about that point by 22 / (22 - z): 2.088; ± is a pixel and the lens's distance","via":"user"}}],"note":"Read on the page's one photo in the frame of its own lug holes. The catalog's other forged flat tops read 2.09 the same way (expo-arms-stripped-upper.rail_top_above_pin, aero-m4e1-threaded-upper.rail_top_above_pin) and the reference model of a mil-spec forging has 2.090."},"rail_slot0_x":{"label":"The rearmost rail slot's centre ahead of the takedown pin","kind":"length","measurements":[{"id":"right","value":1.31,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/psa-stripped-upper 55761f177232 (Palmetto State Armory's product photo 51655109407.jpg, in the page the user saved on 2026-10-12: the stripped receiver's right side on white, 546 x 546)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each see-through opening fitted as its near rim's circle and its far rim's at once (.cache/b46/psa-stripped-upper/lens.py: rims found to 0.05 px), their midpoints the frame's points: 62.96 px/in on the receiver's mid-plane, a pixel 0.016 in; the rail's 13 slots, read at the teeth's near edges, run 1.5% over the standard pitch on it, as a lens some 26 in away makes them","method":"the 13 gaps' centres on rows 207 to 211 run from 1.302 to 6.098 in the frame, bounded by the teeth's near edges 0.41 nearer than the mid-plane: the lens stands about 22 in away opposite x 2.58, y 0.33 (right_photo_lens_*), so what is z nearer than the mid-plane reads large about that point by 22 / (22 - z), and the picture's scale falls 0.26% to the inch toward the muzzle (the tooth tops stand 2.136 over the takedown hole and 2.099 over the pivot's): the first slot at 1.317, the last at 6.030, which is the first at 1.302 by the standard pitch; their mean, ± for the lens's distance and a pixel","via":"user"}}],"note":"Expo Arms' forged flat top reads 1.314 on a photo four times this one's size (expo-arms-stripped-upper.rail_slot0_x): the same forging's rail, within this reading's ±."},"rail_slots":{"label":"How many rail slots","kind":"count","measurements":[{"id":"photo","value":13,"unit":"count","source":{"type":"photo","photo":"references/psa-stripped-upper 55761f177232 (Palmetto State Armory's product photo 51655109407.jpg, in the page the user saved on 2026-10-12: the stripped receiver's right side on white, 546 x 546)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each see-through opening fitted as its near rim's circle and its far rim's at once (.cache/b46/psa-stripped-upper/lens.py: rims found to 0.05 px), their midpoints the frame's points: 62.96 px/in on the receiver's mid-plane, a pixel 0.016 in; the rail's 13 slots, read at the teeth's near edges, run 1.5% over the standard pitch on it, as a lens some 26 in away makes them","method":"the see-through gaps along the top edge, counted on rows 207 to 211 (.cache/b46/psa-stripped-upper/rail.py: 13 on each of four rows)","via":"user"}}],"note":"Behind the first is a solid run of rail over the charging handle's channel (from rail_rear_x), ahead of the last a long tooth to the front shoulder. Unmarked: the page's \"no T marks\"."},"rail_rear_x":{"label":"The top rail's head: where it begins ahead of the tongue, X (the app draws the head from here)","kind":"length","measurements":[{"id":"standard","value":0.4165,"unit":"in","pm":0.006,"source":{"type":"derived","expr":"{std.ar15.rail_tongue_shoulder_x}","via":"user"}}],"note":"Until 2026-10-20 this was the rail's rearmost point (now rail_tongue_rear_x), and the app drew the head at its full width from there, square: the charging handle's T, cut round for a rounded rail end, stood in its corners. Behind this the rail is the standard's tongue (std.ar15.rail_tongue_*), which the receiver's model carries, as the 22RB's does."},"rail_tongue_rear_x":{"label":"The top rail's tongue: its rounded end's rearmost point, X ahead of the takedown pin","kind":"length","measurements":[{"id":"photo","value":-0.57,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/psa-stripped-upper 55761f177232 (Palmetto State Armory's product photo 51655109407.jpg, in the page the user saved on 2026-10-12: the stripped receiver's right side on white, 546 x 546)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each see-through opening fitted as its near rim's circle and its far rim's at once (.cache/b46/psa-stripped-upper/lens.py: rims found to 0.05 px), their midpoints the frame's points: 62.96 px/in on the receiver's mid-plane, a pixel 0.016 in; the rail's 13 slots, read at the teeth's near edges, run 1.5% over the standard pitch on it, as a lens some 26 in away makes them","method":"the rail's tail's rear end in the traced outline (profiles.side): -0.574 at y 2.12, -0.567 at y 1.93, its tip taken on the mid-plane (a mil-spec forging's tail is rounded in plan: expo-arms-stripped-upper.rail_rear_x, -0.588 on a larger photo); ± is a pixel and a half","via":"user"}}]},"rail_front_x":{"label":"The top rail's front end ahead of the takedown pin","kind":"length","measurements":[{"id":"shoulder","value":6.591,"unit":"in","pm":0.011,"source":{"type":"derived","expr":"{.front_face_x} - {std.ar15.upper_barrel_thread_length}","via":"harvest"},"note":"The rail's last tooth ends flush with the body's front shoulder, where the barrel-nut thread begins (the photo): the drawing's .445 REF behind the front face."},{"id":"right","value":6.6,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/psa-stripped-upper 55761f177232 (Palmetto State Armory's product photo 51655109407.jpg, in the page the user saved on 2026-10-12: the stripped receiver's right side on white, 546 x 546)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each see-through opening fitted as its near rim's circle and its far rim's at once (.cache/b46/psa-stripped-upper/lens.py: rims found to 0.05 px), their midpoints the frame's points: 62.96 px/in on the receiver's mid-plane, a pixel 0.016 in; the rail's 13 slots, read at the teeth's near edges, run 1.5% over the standard pitch on it, as a lens some 26 in away makes them","method":"the silhouette's front edge at the rail's height reads 6.669; it is the shoulder's near edge, about 0.37 nearer than the mid-plane: the lens stands about 22 in away opposite x 2.58, y 0.33 (right_photo_lens_*), so what is z nearer than the mid-plane reads large about that point by 22 / (22 - z): 6.600; ± is a pixel and the lens's distance","via":"user"}}],"adopt":{"from":"shoulder","reason":"The drawing's shoulder; the photo's edge lands on it within its ±."},"note":"Ahead of it the receiver is the barrel nut's thread."},"receiver_rear_x":{"label":"The receiver's rear face behind the takedown pin (negative)","kind":"length","measurements":[{"id":"standard","value":-0.621,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.ar15.upper_rear_face_x}","via":"harvest"},"note":"The Army's drawing of the upper (8448524). Palmetto State Armory's page: \"Forged 7075-T6 A3 AR upper is hard coat anodized black for durability. Featuring M4 feedramp cuts and no T marks.\" It names no standard; its being the Army drawing's receiver is what \"A3 AR upper\" is taken to say, and each face is tried on its photo."},{"id":"right","value":-0.63,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/psa-stripped-upper 55761f177232 (Palmetto State Armory's product photo 51655109407.jpg, in the page the user saved on 2026-10-12: the stripped receiver's right side on white, 546 x 546)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each see-through opening fitted as its near rim's circle and its far rim's at once (.cache/b46/psa-stripped-upper/lens.py: rims found to 0.05 px), their midpoints the frame's points: 62.96 px/in on the receiver's mid-plane, a pixel 0.016 in; the rail's 13 slots, read at the teeth's near edges, run 1.5% over the standard pitch on it, as a lens some 26 in away makes them","method":"the silhouette's rear edge at y 1.45 to 1.62 reads -0.720, where the forward assist's housing joins the wall: the lens stands about 22 in away opposite x 2.58, y 0.33 (right_photo_lens_*), so what is z nearer than the mid-plane reads large about that point by 22 / (22 - z); taken as an edge 0.32 nearer than the mid-plane it is -0.67, at 0.6 nearer -0.63, at 0.9 (the housing's root) -0.58: ± covers that","via":"user"}}],"adopt":{"from":"standard","reason":"The drawing dimensions the face; the photo agrees with it within its ±."}},"front_face_x":{"label":"The receiver's front face (the end of its barrel-nut thread) ahead of the takedown pin","kind":"length","measurements":[{"id":"standard","value":7.036,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.ar15.upper_front_face_x}","via":"harvest"},"note":"The Army's drawing: .661 ahead of the pivot lug's hole. Palmetto State Armory's page: \"Forged 7075-T6 A3 AR upper is hard coat anodized black for durability. Featuring M4 feedramp cuts and no T marks.\" It names no standard; its being the Army drawing's receiver is what \"A3 AR upper\" is taken to say, and each face is tried on its photo."},{"id":"right","value":7.05,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/psa-stripped-upper 55761f177232 (Palmetto State Armory's product photo 51655109407.jpg, in the page the user saved on 2026-10-12: the stripped receiver's right side on white, 546 x 546)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each see-through opening fitted as its near rim's circle and its far rim's at once (.cache/b46/psa-stripped-upper/lens.py: rims found to 0.05 px), their midpoints the frame's points: 62.96 px/in on the receiver's mid-plane, a pixel 0.016 in; the rail's 13 slots, read at the teeth's near edges, run 1.5% over the standard pitch on it, as a lens some 26 in away makes them","method":"the silhouette's front tip reads 7.172: the thread's near rim, 0.62 nearer than the mid-plane and 4.6 in from where the lens stands: the lens stands about 22 in away opposite x 2.58, y 0.33 (right_photo_lens_*), so what is z nearer than the mid-plane reads large about that point by 22 / (22 - z): 7.043, and 0.006 more for the picture's fall of scale toward the muzzle; ± is a pixel and the lens's distance (18.7 in makes it 7.02, 25.7 in 7.06)","via":"user"}}],"adopt":{"from":"standard","reason":"The drawing dimensions the face; the photo lands on it within its ±."}},"underside_y":{"label":"The receiver's underside above the pin line","kind":"length","measurements":[{"id":"standard","value":0.2485,"unit":"in","pm":0.0015,"source":{"type":"derived","expr":"{std.ar15.deck_y}","via":"harvest"},"note":"It sits on the lower's deck."},{"id":"right","value":0.245,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/psa-stripped-upper 55761f177232 (Palmetto State Armory's product photo 51655109407.jpg, in the page the user saved on 2026-10-12: the stripped receiver's right side on white, 546 x 546)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each see-through opening fitted as its near rim's circle and its far rim's at once (.cache/b46/psa-stripped-upper/lens.py: rims found to 0.05 px), their midpoints the frame's points: 62.96 px/in on the receiver's mid-plane, a pixel 0.016 in; the rail's 13 slots, read at the teeth's near edges, run 1.5% over the standard pitch on it, as a lens some 26 in away makes them","method":"the silhouette's lower edge between the lugs reads 0.243 over x 1.0 to 5.5: the wall's near lower edge, 0.45 nearer than the mid-plane and 0.09 below where the lens stands: the lens stands about 22 in away opposite x 2.58, y 0.33 (right_photo_lens_*), so what is z nearer than the mid-plane reads large about that point by 22 / (22 - z): 0.002 more; ± is a pixel","via":"user"}}],"adopt":{"from":"standard","reason":"The lower's deck; the photo's edge lands on it within its ±."}},"width":{"label":"Width of the receiver's body","kind":"length","measurements":[{"id":"tdp","value":1.18,"unit":"in","pm":0.02,"stated":"FORGED DIA 1.18 DIA REF -V-","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 2 of 2, rev G: View G-G; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p109","via":"user"},"note":"The round body just behind the threaded nose, as aero-m4e1-threaded-upper.width reads it. Not measured on this receiver: its page has one photo, of its side."}],"note":"The mil-spec forging's: the page calls it a \"Forged 7075-T6 A3 AR upper\". Its forward assist's housing and brass deflector stand out past it on the right."},"notch_bottom_y":{"label":"The notch under the rail's rear end (the charging handle's room), its floor above the pin line","kind":"length","measurements":[{"id":"photo","value":1.6,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/psa-stripped-upper 55761f177232 (Palmetto State Armory's product photo 51655109407.jpg, in the page the user saved on 2026-10-12: the stripped receiver's right side on white, 546 x 546)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each see-through opening fitted as its near rim's circle and its far rim's at once (.cache/b46/psa-stripped-upper/lens.py: rims found to 0.05 px), their midpoints the frame's points: 62.96 px/in on the receiver's mid-plane, a pixel 0.016 in; the rail's 13 slots, read at the teeth's near edges, run 1.5% over the standard pitch on it, as a lens some 26 in away makes them","method":"the see-through notch's lower edge in the traced outline (profiles.side) reads 1.631 at x -0.5 to -0.1; there the picture is 0.9% larger than between the holes (the rear end nearer the lens): 1.616; and what bounds a see-through from below is the wall's near upper edge, 0.32 nearer than the mid-plane and 1.3 above where the lens stands: the lens stands about 22 in away opposite x 2.58, y 0.33 (right_photo_lens_*), so what is z nearer than the mid-plane reads large about that point by 22 / (22 - z): 1.597; ± is a pixel and a half","via":"user"}}],"note":"The wall's top behind the notch's front wall: what a charging handle's block lies on."},"notch_top_y":{"label":"The notch under the rail's rear end, its roof (the rail's tail's underside) above the pin line","kind":"length","measurements":[{"id":"photo","value":1.89,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/psa-stripped-upper 55761f177232 (Palmetto State Armory's product photo 51655109407.jpg, in the page the user saved on 2026-10-12: the stripped receiver's right side on white, 546 x 546)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each see-through opening fitted as its near rim's circle and its far rim's at once (.cache/b46/psa-stripped-upper/lens.py: rims found to 0.05 px), their midpoints the frame's points: 62.96 px/in on the receiver's mid-plane, a pixel 0.016 in; the rail's 13 slots, read at the teeth's near edges, run 1.5% over the standard pitch on it, as a lens some 26 in away makes them","method":"the see-through notch's upper edge in the traced outline (profiles.side), the rail's tail's underside, reads 1.884; 0.9% less for the picture's scale at that end: 1.867; and what bounds a see-through from above is the far lower edge, 0.31 further than the mid-plane and 1.5 above where the lens stands: 1.888; ± is a pixel and a half. The notch is 0.29 high so, for the 0.31 to 0.32 the Army's drawing scales to (expo-arms-stripped-upper.handle_seat_x) and a handle .2985 thick","via":"user"}}]},"charging_handle_above_bore":{"label":"The charging handle's channel above the bore's axis","kind":"length","measurements":[{"id":"photo","value":0.87,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/psa-stripped-upper 55761f177232 (Palmetto State Armory's product photo 51655109407.jpg, in the page the user saved on 2026-10-12: the stripped receiver's right side on white, 546 x 546)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each see-through opening fitted as its near rim's circle and its far rim's at once (.cache/b46/psa-stripped-upper/lens.py: rims found to 0.05 px), their midpoints the frame's points: 62.96 px/in on the receiver's mid-plane, a pixel 0.016 in; the rail's 13 slots, read at the teeth's near edges, run 1.5% over the standard pitch on it, as a lens some 26 in away makes them","method":"the notch in the rear end, from the wall's top to the rail's tail's underside: 1.597 to 1.888 once its two edges are brought back through the lens (notch_bottom_y, notch_top_y): its middle 1.743, less the bore's 0.8775: 0.865","via":"user"}},{"id":"standard","value":0.8563,"unit":"in","pm":0.007,"source":{"type":"derived","expr":"{std.ar15.charging_handle_axis_y} - {.bore_axis_above_pin}","via":"user"},"note":"Riding on its guide lugs on the channel's tier: std.ar15.charging_handle_axis_y."}],"adopt":{"from":"standard","reason":"A handle rides on its guide lugs on the channel's tier (std.ar15.charging_handle_axis_y, the Army's drawing's); the photo reads the see-through notch's middle, which is the room the handle's block lies in, and agrees within its ±."},"note":"The notch the handle's latch end lies in: the handle lies at its height (as expo-arms-stripped-upper.charging_handle_above_bore, 0.87)."},"handle_seat_x":{"label":"The charging handle's seat: the front wall of the open notch under the rail's rear end, ahead of the takedown pin","kind":"length","measurements":[{"id":"right","value":0.06,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/psa-stripped-upper 55761f177232 (Palmetto State Armory's product photo 51655109407.jpg, in the page the user saved on 2026-10-12: the stripped receiver's right side on white, 546 x 546)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each see-through opening fitted as its near rim's circle and its far rim's at once (.cache/b46/psa-stripped-upper/lens.py: rims found to 0.05 px), their midpoints the frame's points: 62.96 px/in on the receiver's mid-plane, a pixel 0.016 in; the rail's 13 slots, read at the teeth's near edges, run 1.5% over the standard pitch on it, as a lens some 26 in away makes them","method":"the see-through notch's front wall in the traced outline (profiles.side): its flat at x 0.060 from y 1.732 to 1.859, between two corners cut back to x 0.037 and -0.028. What shows through a notch is bounded by the wall's near edge, 0.32 to 0.45 nearer than the mid-plane: the lens stands about 22 in away opposite x 2.58, y 0.33 (right_photo_lens_*), so what is z nearer than the mid-plane reads large about that point by 22 / (22 - z), so that edge reads 0.04 behind the wall itself, which would be at 0.10; ± covers the pixel (0.016) and half of that","via":"user"}},{"id":"tdp","value":0.075,"unit":"in","pm":0.015,"source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: side elevation, scaled (the notch has no callout in this view); user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"},"note":"Scaled, not a callout. On the 6600 px scan the two lug holes, fitted as circles, are 1966 px apart (308.4 px/in over std.ar15.pin_spacing) and the notch's front wall (column 2427.5) is 21.5 px ahead of the takedown hole's centre: 0.070. From the rear face's line, 217 px behind the wall, it is 0.083: the drawing dimensions that face at -0.621 and the scan has it at -0.634 by the holes. Between the two; ± covers both. The notch is 0.31 to 0.32 high there, for the handle's .2985 (drawing 8448518), its front corners cut back 0.06."}],"adopt":{"from":"right","reason":"This receiver's own notch in the outline its model is built from, where the model's wall is: a handle seated there stands in nothing. The Army's drawing, scaled, reads +0.015 from it, inside both ±."},"note":"Where a charging handle stops: the front wall of the notch cut across the receiver under the rail's rear end, open to the rear. The handle's block lies in it with its shoulder against this wall, and the shaft runs on through the slot ahead of it (expo-arms-stripped-upper.handle_seat_x has the photo of one seated)."},"right_photo_lens_distance":{"label":"The side photo: its lens's distance from the receiver's mid-plane","kind":"length","measurements":[{"id":"holes","value":22,"unit":"in","pm":4,"source":{"type":"photo","photo":"references/psa-stripped-upper 55761f177232 (Palmetto State Armory's product photo 51655109407.jpg, in the page the user saved on 2026-10-12: the stripped receiver's right side on white, 546 x 546)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each see-through opening fitted as its near rim's circle and its far rim's at once (.cache/b46/psa-stripped-upper/lens.py: rims found to 0.05 px), their midpoints the frame's points: 62.96 px/in on the receiver's mid-plane, a pixel 0.016 in; the rail's 13 slots, read at the teeth's near edges, run 1.5% over the standard pitch on it, as a lens some 26 in away makes them","method":"two readings, 7 in apart: the lug holes' rims (.cache/b46/psa-stripped-upper/lens.py: each see-through opening as its near rim's circle and its far rim's, the far one off toward the point the lens is opposite, both holes fitted at once with the picture's blur) give 18.7, the fit's own ± 0.2 and its residual large (the bores' lit walls aren't in it); the rail's 13 slots, bounded at the teeth's near edges 0.41 out, run 25.17 px to the slot for the mid-plane's 24.80 (.cache/b46/psa-stripped-upper/rail.py), 1.65% long once the picture's own fall of scale along the receiver is out of it: 25.7. Taken between them; ± covers both, and moves what is read 1.1 in out (the forward assist's rear face) by 0.03","via":"user"}}],"note":"A property of Palmetto State Armory's photo 55761f177232, not of the receiver: the model corrects what the right side shows nearer the lens (the forward assist's rear face, the deflector, the hinge lugs, the lugs) by it."},"right_photo_lens_x":{"label":"The side photo: where its lens stands, X","kind":"length","measurements":[{"id":"holes","value":2.58,"unit":"in","pm":0.3,"source":{"type":"photo","photo":"references/psa-stripped-upper 55761f177232 (Palmetto State Armory's product photo 51655109407.jpg, in the page the user saved on 2026-10-12: the stripped receiver's right side on white, 546 x 546)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each see-through opening fitted as its near rim's circle and its far rim's at once (.cache/b46/psa-stripped-upper/lens.py: rims found to 0.05 px), their midpoints the frame's points: 62.96 px/in on the receiver's mid-plane, a pixel 0.016 in; the rail's 13 slots, read at the teeth's near edges, run 1.5% over the standard pitch on it, as a lens some 26 in away makes them","method":"as right_photo_lens_distance: the two holes' far rims sit off their near ones toward px (235.5, 318.6), the fit's ± 2.2 px; the rail's teeth show their rear faces ahead of about x 3.5 and none behind it. ± is widened for the fit's residual","via":"user"}}]},"right_photo_lens_y":{"label":"The side photo: where its lens stands, Y","kind":"length","measurements":[{"id":"holes","value":0.33,"unit":"in","pm":0.3,"source":{"type":"photo","photo":"references/psa-stripped-upper 55761f177232 (Palmetto State Armory's product photo 51655109407.jpg, in the page the user saved on 2026-10-12: the stripped receiver's right side on white, 546 x 546)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each see-through opening fitted as its near rim's circle and its far rim's at once (.cache/b46/psa-stripped-upper/lens.py: rims found to 0.05 px), their midpoints the frame's points: 62.96 px/in on the receiver's mid-plane, a pixel 0.016 in; the rail's 13 slots, read at the teeth's near edges, run 1.5% over the standard pitch on it, as a lens some 26 in away makes them","method":"as right_photo_lens_x: px row 318.6, the fit's ± 2.9 px: about level with the lugs, under the bore","via":"user"}}]},"body_radius":{"label":"The round body's radius about the bore (the forging's)","kind":"length","measurements":[{"id":"tdp","value":0.59,"unit":"in","pm":0.01,"stated":"FORGED DIA 1.18 DIA REF -V-","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 2 of 2, rev G: View G-G; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p109","via":"user"}},{"id":"model","value":0.6,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): cylindrical faces r 0.6000 about the bore's axis, x -0.43 to 6.59","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's forged figure; the model's is 0.01 more."}},"bore_d":{"label":"The bore the bolt carrier runs in","kind":"length","measurements":[{"id":"tdp","value":1,"unit":"in","pm":0.002,"stated":"DIA -P- (IN 1.000 DIA ±.002 AREA)","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: note 4; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}}]},"dovetail_foot_y":{"label":"The rail's dovetail, its foot (where the neck begins), Y above the pin line","kind":"length","measurements":[{"id":"model","value":1.885,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the planes under the dovetail at y 1.885, z 0.309 to 0.333","via":"user"}}]},"dovetail_foot_half_width":{"label":"The rail's dovetail at its foot, half its width","kind":"length","measurements":[{"id":"model","value":0.333,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the planes at y 1.885 reach z 0.333","via":"user"}},{"id":"std","value":0.323,"unit":"in","pm":0.013,"source":{"type":"derived","expr":"{std.picatinny.bevel_width} / 2 + {std.picatinny.lower_gauge_below_top} - ({.rail_top_above_pin} - {.dovetail_foot_y})","via":"harvest"},"note":"The standard's lower face carried on at its 45 degrees from the lower gauge line (.748 across, .154 below the rail's top) to the height the reference model has the foot at: the face every other rail on file has (the teeth the app draws on this body, a handguard's own rail) and every clamp's channel is cut to. ± is the gauge line's .010 and the model's .003."}],"adopt":{"from":"std","reason":"The standard's: a rail's head is MIL-STD-1913's, and every clamp's channel is cut to it (pipeline/blender/lib.py rail_seat). The reference model draws the same face a hundredth further out, at the standard's stated .164 where the ledger has the middle of .164 -.020 (std.picatinny.lower_gauge_below_top): inside the standard's band, but a body drawn so stands in every clamp (expo-arms-stripped-upper.dovetail_foot_half_width). The model isn't authoritative beside the standard (D49); its neck and the foot's height are still its own."}},"rail_neck_half_width":{"label":"The rail's neck below its dovetail, half its width","kind":"length","measurements":[{"id":"model","value":0.309,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the planes at y 1.700 and 1.885 begin at z 0.309","via":"user"}}]},"rail_neck_bottom_y":{"label":"The rail's neck, where it meets the receiver's sides, Y","kind":"length","measurements":[{"id":"model","value":1.7,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the planes at y 1.700, z 0.309 to 0.319","via":"user"}}]},"side_half_width":{"label":"The receiver's sides below the rail's neck, half its width","kind":"length","measurements":[{"id":"model","value":0.319,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the planes at y 1.700 end at z 0.319; a .10 fillet below them","via":"user"}}]},"side_bottom_y":{"label":"The receiver's sides, where they turn into the round body, Y","kind":"length","measurements":[{"id":"model","value":1.44,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the r .10 fillet between the flat side and the round body, its axis at y 1.440, z 0.419","via":"user"}}]},"lug_wall_half_width":{"label":"The walls below the round body down to the underside, half the width","kind":"length","measurements":[{"id":"model","value":0.453,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the r .075 fillets at y 0.458, their axes at z 0.528","via":"user"}}]},"rear_flange_r":{"label":"The flange round the rear end, its radius about the bore","kind":"length","measurements":[{"id":"model","value":0.6938,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): cylindrical faces r 0.6938 about the bore's axis from the rear face to x -0.470, on both sides","via":"user"}}],"note":"The raised lip that follows the rear end's contour, the forging's."},"rear_flange_front_x":{"label":"The rear flange's front face, X","kind":"length","measurements":[{"id":"model","value":-0.47,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the r 0.6938 faces end at x -0.470","via":"user"}}]},"lug_width":{"label":"The takedown and pivot lugs' width","kind":"length","measurements":[{"id":"tdp","value":0.4945,"unit":"in","pm":0.0015,"stated":".496 -.003 BOTH LUGS","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: the rear elevation; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}}],"note":"The reference model has them 0.494."},"lug_rear_face_top_y":{"label":"The takedown lug's rear face, how high it rises into the body, Y","kind":"length","measurements":[{"id":"model","value":0.458,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/batch123/expo-arms-stripped-upper/cad.py): the plane x -0.236 from y -0.212 to 0.458; the r .75 corner faces lie outside z ±0.247","via":"user"}}],"note":"Behind it the body's lower rear is cut away either side of the lug's width, to the arc a lower's rear walls rise along (std.ar15.rear_wall_arc_r; the upper's own is std.ar15.upper_rear_corner_r)."},"lug_hole_d":{"label":"The lugs' pin holes","kind":"length","measurements":[{"id":"tdp","value":0.251,"unit":"in","pm":0.001,"stated":".250 DIA +.002 THRU (the takedown lug's, CSK .31 DIA X 90 INCL THIS SIDE ONLY); .250 DIA +.001 THRU (the pivot lug's)","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: side elevation; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}}],"note":"The photo's two holes are fitted with this diameter (right_photo_lens_*)."},"barrel_thread_major_d":{"label":"The barrel-nut thread's major diameter","kind":"length","measurements":[{"id":"tdp","value":1.2442,"unit":"in","pm":0.0044,"stated":"1 1/4 -18 UNEF-2A MAJOR DIA - 1.2485/1.2398 (AFTER ANODIZE)","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: plan view, the threaded end; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}},{"id":"photo","value":1.236,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/psa-stripped-upper 55761f177232 (Palmetto State Armory's product photo 51655109407.jpg, in the page the user saved on 2026-10-12: the stripped receiver's right side on white, 546 x 546)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each see-through opening fitted as its near rim's circle and its far rim's at once (.cache/b46/psa-stripped-upper/lens.py: rims found to 0.05 px), their midpoints the frame's points: 62.96 px/in on the receiver's mid-plane, a pixel 0.016 in; the rail's 13 slots, read at the teeth's near edges, run 1.5% over the standard pitch on it, as a lens some 26 in away makes them","method":"the nose's top to its bottom over x 6.75 to 6.95: 1.224, and the picture 0.94% smaller at that end than between the holes: 1.236; ± is a pixel each side. A black thread on white reads thin, its crests' tips lost","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's thread: the barrel nut's is the same on every AR-15 receiver, and the page calls this an \"A3 AR upper\"; the photo reads under, as a black thread does on white at this size."}},"barrel_thread_minor_d":{"label":"The barrel-nut thread's minor diameter","kind":"length","measurements":[{"id":"tdp","value":1.1803,"unit":"in","pm":0.003,"stated":"MINOR DIA - 1.1803 MAX","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: plan view, the threaded end; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}}]},"barrel_thread_tpi":{"label":"The barrel-nut thread's turns to the inch","kind":"count","measurements":[{"id":"tdp","value":18,"unit":"count","pm":0,"stated":"1 1/4 -18 UNEF-2A","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: plan view, the threaded end; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}}]},"gas_tube_hole_d":{"label":"The gas tube's hole in the front shoulder","kind":"length","measurements":[{"id":"tdp","value":0.1835,"unit":"in","pm":0.0015,"stated":".182 DIA +.003 THRU; .312 DIA +.010 BACK BORE","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 2 of 2, rev G: View F-F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p109","via":"user"}},{"id":"model","value":0.175,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): a cylinder r 0.0875 along x at y 1.662, z 0 (0.783 above the bore), x 6.401 to 6.591","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's callout (D49); the model's hole is 0.008 smaller."},"note":"Above the thread on the bore's mid-plane, std.ar15.gas_tube_above_bore above the bore. Not visible in this receiver's one photo: the drawing's."},"gas_tube_relief_d":{"label":"The gas tube hole's four corner reliefs, diameter","kind":"length","measurements":[{"id":"tdp","value":0.094,"unit":"in","pm":0.002,"stated":".047 R, 4 PLACES EQUALLY SPACED RANDOM ORIENTATION EXCEPT MUST NOT INTERSECT THREADS","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 2 of 2, rev G: View F-F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p109","via":"user"}},{"id":"model","value":0.09,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): four cylinders r 0.0450 along x round the gas tube's hole","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's radius; the model's is 0.002 less."}},"gas_tube_relief_offset":{"label":"The gas tube hole's corner reliefs, off its centre each way","kind":"length","measurements":[{"id":"model","value":0.078,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): their axes at y 1.585 and 1.740, z ±0.078: 0.0775 and 0.078 off the hole's centre","via":"user"}}]},"port_length":{"label":"The ejection port's length","kind":"length","measurements":[{"id":"tdp","value":3.125,"unit":"in","pm":0.005,"stated":"3.125; .25 R TRUE 2 PLACES; 1.562 ±.010","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: side elevation; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}},{"id":"photo","value":3.07,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/psa-stripped-upper 55761f177232 (Palmetto State Armory's product photo 51655109407.jpg, in the page the user saved on 2026-10-12: the stripped receiver's right side on white, 546 x 546)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each see-through opening fitted as its near rim's circle and its far rim's at once (.cache/b46/psa-stripped-upper/lens.py: rims found to 0.05 px), their midpoints the frame's points: 62.96 px/in on the receiver's mid-plane, a pixel 0.016 in; the rail's 13 slots, read at the teeth's near edges, run 1.5% over the standard pitch on it, as a lens some 26 in away makes them","method":"the dark opening from px column 261 to 459: 2.981 to 6.126, in the wall 0.55 nearer than the mid-plane: the lens stands about 22 in away opposite x 2.58, y 0.33 (right_photo_lens_*), so what is z nearer than the mid-plane reads large about that point by 22 / (22 - z): 2.971 to 6.037; ± is two pixels","via":"user"}}],"adopt":{"from":"tdp","reason":"The callout; the brass deflector, added after the port is cut, sets the opening's rear end where the photo shows it."},"note":"The opening reads short of the callout, as it does on Expo Arms' and Aero's photos and on the reference model (3.097): the drawing marks .005 and .042 beside the 3.125's two ends, which may be the opening's own ends inside it."},"port_front_x":{"label":"The ejection port's front end ahead of the takedown pin","kind":"length","measurements":[{"id":"tdp","value":6.036,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{.front_face_x} - 1.00in","via":"user"},"note":"8448524 sheet 1: \"1.00\" from the 3.125's front end to the receiver's front end (read on the scan at 309 px/in: the two extension lines are 1.00 apart)."},{"id":"photo","value":6.04,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/psa-stripped-upper 55761f177232 (Palmetto State Armory's product photo 51655109407.jpg, in the page the user saved on 2026-10-12: the stripped receiver's right side on white, 546 x 546)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each see-through opening fitted as its near rim's circle and its far rim's at once (.cache/b46/psa-stripped-upper/lens.py: rims found to 0.05 px), their midpoints the frame's points: 62.96 px/in on the receiver's mid-plane, a pixel 0.016 in; the rail's 13 slots, read at the teeth's near edges, run 1.5% over the standard pitch on it, as a lens some 26 in away makes them","method":"the opening's front end, px column 459: 6.126, corrected as port_length","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing; the photo agrees within its ±."}},"port_bottom_y":{"label":"The port's lower edge above the pin line, seen from the side (its ends R .25: 0.50 high)","kind":"length","measurements":[{"id":"drawn","value":0.841,"unit":"in","pm":0.01,"source":{"type":"standard","doc":"8448524 sheet 1 side view, scaled (not a callout): its lower straight edge at px row 3640 against the lug holes' row 3900 at the sheet's own 309.3 px/in (the lug holes 6.375 apart), as aero-m4e1-threaded-upper.port_bottom_y read it; a half-size crop reads 0.847 here","via":"user"}},{"id":"photo","value":0.87,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/psa-stripped-upper 55761f177232 (Palmetto State Armory's product photo 51655109407.jpg, in the page the user saved on 2026-10-12: the stripped receiver's right side on white, 546 x 546)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each see-through opening fitted as its near rim's circle and its far rim's at once (.cache/b46/psa-stripped-upper/lens.py: rims found to 0.05 px), their midpoints the frame's points: 62.96 px/in on the receiver's mid-plane, a pixel 0.016 in; the rail's 13 slots, read at the teeth's near edges, run 1.5% over the standard pitch on it, as a lens some 26 in away makes them","method":"the dark opening's lower edge, px row 283: 0.881 above the pin line there, corrected as port_length; its upper edge reads 0.5 above it","via":"user"}}],"adopt":{"from":"drawn","reason":"The drawing's outline at its own scale; the photo agrees within its ±."}},"port_end_r":{"label":"The port's ends' radius (half its height from the side)","kind":"length","measurements":[{"id":"tdp","value":0.25,"unit":"in","pm":0.005,"stated":".25 R TRUE 2 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: side elevation; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}}]},"fa_axis_angle":{"label":"The forward assist's axis, turned inward toward the front in plan","kind":"angle","measurements":[{"id":"tdp","value":20,"unit":"deg","pm":1,"stated":"20°","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: the plan view's forward assist section (CL HOLE at 20°, 1.0285 ±.0050, .509 DIA ±.003, .315 DIA ±.001); user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}}],"note":"The reference model has 22.5 (aero-m4e1-threaded-upper.fa_axis_angle): the drawing wins (D49)."},"fa_bore_d":{"label":"The forward assist's bore","kind":"length","measurements":[{"id":"tdp","value":0.509,"unit":"in","pm":0.003,"stated":".509 DIA ±.003","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: the plan view's forward assist section; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}}]},"fa_bore_depth":{"label":"The forward assist's bore, how deep its .509 runs from the housing's rear face","kind":"length","measurements":[{"id":"tdp","value":0.65,"unit":"in","pm":0.01,"stated":".65","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: the plan view's forward assist section; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}}],"note":"Read as the .509 bore's depth along its axis; ahead of it the hole is the .315."},"fa_inner_bore_d":{"label":"The forward assist's inner bore, ahead of the .509","kind":"length","measurements":[{"id":"tdp","value":0.315,"unit":"in","pm":0.001,"stated":".315 DIA ±.001","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: the plan view's forward assist section; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}}]},"fa_axis_x":{"label":"The forward assist's axis: a point on it, X","kind":"length","measurements":[{"id":"model","value":-0.395,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the r .25 bore's axis through (-0.395, 0.879, 1.090)","via":"user"}}],"note":"With fa_axis_z and the drawing's angle this places the axis; scaled off the drawing's plan view (309 px/in) the hole's centre line is 1.0285 from the receiver's centre line 0.41 ahead of the rear face, which puts it at 1.097 here."},"fa_axis_z":{"label":"The forward assist's axis: that point out from the middle (Z)","kind":"length","measurements":[{"id":"model","value":1.09,"unit":"in","pm":0.01,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the r .25 bore's axis through (-0.395, 0.879, 1.090)","via":"user"}}]},"fa_rear_x":{"label":"The forward assist housing's rear face where the axis crosses it, X","kind":"length","measurements":[{"id":"photo","value":-0.53,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/psa-stripped-upper 55761f177232 (Palmetto State Armory's product photo 51655109407.jpg, in the page the user saved on 2026-10-12: the stripped receiver's right side on white, 546 x 546)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each see-through opening fitted as its near rim's circle and its far rim's at once (.cache/b46/psa-stripped-upper/lens.py: rims found to 0.05 px), their midpoints the frame's points: 62.96 px/in on the receiver's mid-plane, a pixel 0.016 in; the rail's 13 slots, read at the teeth's near edges, run 1.5% over the standard pitch on it, as a lens some 26 in away makes them","method":"the bore's opening at the housing's rear, the dark ellipse about px column 29.5: -0.697, 1.13 nearer than the mid-plane: the lens stands about 22 in away opposite x 2.58, y 0.33 (right_photo_lens_*), so what is z nearer than the mid-plane reads large about that point by 22 / (22 - z); ± is a pixel and what the lens's distance leaves (0.03)","via":"user"}}],"note":"The housing runs back to the rear end, as the drawing's side view has it and as Expo Arms' forging does (expo-arms-stripped-upper.fa_rear_x: -0.49 on a larger photo); the reference model's stops at -0.34."},"fa_housing_r":{"label":"The forward assist housing's radius about its axis","kind":"length","measurements":[{"id":"model","value":0.3125,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the housing's cylinder r .3125 on the bore's axis","via":"user"}},{"id":"photo","value":0.32,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/psa-stripped-upper 55761f177232 (Palmetto State Armory's product photo 51655109407.jpg, in the page the user saved on 2026-10-12: the stripped receiver's right side on white, 546 x 546)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each see-through opening fitted as its near rim's circle and its far rim's at once (.cache/b46/psa-stripped-upper/lens.py: rims found to 0.05 px), their midpoints the frame's points: 62.96 px/in on the receiver's mid-plane, a pixel 0.016 in; the rail's 13 slots, read at the teeth's near edges, run 1.5% over the standard pitch on it, as a lens some 26 in away makes them","method":"the housing's rear rim, px rows 259 to 301: 0.667 high, 1.13 nearer than the mid-plane: the lens stands about 22 in away opposite x 2.58, y 0.33 (right_photo_lens_*), so what is z nearer than the mid-plane reads large about that point by 22 / (22 - z); halved; ± is a pixel each side","via":"user"}}],"adopt":{"from":"model","reason":"The forging's; the photo's rim agrees within its ±."}},"deflector_out":{"label":"The brass deflector's crest, out from the middle (Z; the forging's)","kind":"length","measurements":[{"id":"model","value":1.25,"unit":"in","pm":0.05,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): its crest's faces (a sphere and r .125, r 1.35 cylinders) reach z 1.20 to 1.30 at x 2.31 to 2.34, y 1.11 to 1.32","via":"user"}}],"note":"The mil-spec forging's: no end or top view of this receiver is on file to read its own on."},"deflector_crest_x":{"label":"The deflector's crest, X","kind":"length","measurements":[{"id":"model","value":2.32,"unit":"in","pm":0.02,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): its crest's faces at x 2.308 to 2.337","via":"user"}},{"id":"photo","value":2.4,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/psa-stripped-upper 55761f177232 (Palmetto State Armory's product photo 51655109407.jpg, in the page the user saved on 2026-10-12: the stripped receiver's right side on white, 546 x 546)","scaleRef":"its own lug holes, std.ar15.pin_spacing apart: each see-through opening fitted as its near rim's circle and its far rim's at once (.cache/b46/psa-stripped-upper/lens.py: rims found to 0.05 px), their midpoints the frame's points: 62.96 px/in on the receiver's mid-plane, a pixel 0.016 in; the rail's 13 slots, read at the teeth's near edges, run 1.5% over the standard pitch on it, as a lens some 26 in away makes them","method":"the crease between its steep rear face and its long slope, px columns 221 to 224 on a lightened enlargement (.cache/b46/psa-stripped-upper/t-b.png): 2.387, 1.25 nearer than the mid-plane: the lens stands about 22 in away opposite x 2.58, y 0.33 (right_photo_lens_*), so what is z nearer than the mid-plane reads large about that point by 22 / (22 - z); ± is three pixels: the crease is soft at this size","via":"user"}}],"adopt":{"from":"model","reason":"The model places the crest. This receiver's photo has the crease 0.08 further forward, read on a lightened enlargement of a 546 px picture: a difference that stays in sight, and that an end or a top view would settle."}},"deflector_front_out":{"label":"The deflector's slope where it ends at the port, out from the middle (Z; the forging's)","kind":"length","measurements":[{"id":"model","value":0.82,"unit":"in","pm":0.03,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): its slope's faces come down to z 0.813 at x 2.886","via":"user"}}]},"hinge_axis_y":{"label":"The port door's hinge pin, Y","kind":"length","measurements":[{"id":"model","value":0.641,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the two lugs' r .0625 holes and r .1365 bosses on one axis at y 0.641, z 0.689","via":"user"}}],"note":"This receiver's photo shows its two hinge lugs about where the model has them (profiles.side, hinge_rear and hinge_front, brought back through the lens): the rear one from 2.82 to 2.94 against the model's 2.837 to 2.932, the front one from 6.12 to 6.29 against 6.079 to 6.235, three pixels ahead. Each is drawn where the photo has it."},"hinge_axis_z":{"label":"The port door's hinge pin, out from the middle (Z)","kind":"length","measurements":[{"id":"model","value":0.689,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): as hinge_axis_y","via":"user"}}]},"hinge_boss_r":{"label":"The hinge lugs' radius about the pin","kind":"length","measurements":[{"id":"model","value":0.1365,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the lugs' cylindrical faces r .1365","via":"user"}}]},"hinge_pin_d":{"label":"The hinge pin's hole","kind":"length","measurements":[{"id":"tdp","value":0.1295,"unit":"in","pm":0.0015,"stated":".128 DIA +.003 THRU 2 HOLES IN LINE","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 2 of 2, rev G: Section B-B; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p109","via":"user"}},{"id":"model","value":0.125,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/batch123/expo-arms-stripped-upper/cad.py): the lugs' holes r .0625","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's callout; the model's holes are 0.004 smaller."}},"cam_pad_face_z":{"label":"The cam pin's pad on the left side, its face out from the middle (Z, to the left)","kind":"length","measurements":[{"id":"model","value":0.5625,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/batch123/bcm-m4-upper/cad_ch.py): the round along the pad's top edge, r 0.0938 about an axis along x at (y 1.486, z -0.469), so its face at z -0.563; expo-arms-stripped-upper.cam_pad_face_z reads the same file's flat face at z -0.561 to -0.564 over x 4.60 to 5.58, y 1.05 to 1.63","via":"user"}}],"note":"The pad over the cam pin's travel is the forging's: the Army's machined drawing doesn't show it. The page has no view of the left side: this is the mil-spec forging's, not read on this receiver."},"cam_pad_rear_x":{"label":"The cam pin's pad, its face's rear edge ahead of the takedown pin","kind":"length","measurements":[{"id":"model","value":4.6,"unit":"in","pm":0.01,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/batch123/expo-arms-stripped-upper/cad.py, as expo-arms-stripped-upper.cam_pad_face_z records it): the pad's flat face at z -0.561 to -0.564 over x 4.60 to 5.58, y 1.05 to 1.63","via":"user"}}],"note":"The page has no view of the left side: this is the mil-spec forging's, not read on this receiver."},"cam_pad_front_x":{"label":"The cam pin's pad, its face's front edge","kind":"length","measurements":[{"id":"model","value":5.58,"unit":"in","pm":0.01,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/batch123/expo-arms-stripped-upper/cad.py, as expo-arms-stripped-upper.cam_pad_face_z records it): the pad's flat face at z -0.561 to -0.564 over x 4.60 to 5.58, y 1.05 to 1.63","via":"user"}}],"note":"The page has no view of the left side: this is the mil-spec forging's, not read on this receiver."},"cam_pad_bottom_y":{"label":"The cam pin's pad, its face's lower edge above the pin line","kind":"length","measurements":[{"id":"model","value":1.05,"unit":"in","pm":0.01,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/batch123/expo-arms-stripped-upper/cad.py, as expo-arms-stripped-upper.cam_pad_face_z records it): the pad's flat face at z -0.561 to -0.564 over x 4.60 to 5.58, y 1.05 to 1.63","via":"user"}}],"note":"The page has no view of the left side: this is the mil-spec forging's, not read on this receiver. Its lower edge runs into the round body."},"cam_pad_top_y":{"label":"The cam pin's pad, its face's upper edge","kind":"length","measurements":[{"id":"model","value":1.63,"unit":"in","pm":0.01,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/batch123/expo-arms-stripped-upper/cad.py, as expo-arms-stripped-upper.cam_pad_face_z records it): the pad's flat face at z -0.561 to -0.564 over x 4.60 to 5.58, y 1.05 to 1.63","via":"user"}}],"note":"The page has no view of the left side: this is the mil-spec forging's, not read on this receiver."},"cam_pad_edge_round":{"label":"The cam pin's pad, the round along its face's edges and at its upper corners","kind":"length","measurements":[{"id":"model","value":0.094,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/batch123/bcm-m4-upper/cad_ch.py): the round along the pad's top edge, r 0.0938 about (y 1.486, z -0.469), and its two upper corners' rounds about z, r 0.0938 at x 4.695 and 5.488","via":"user"}}],"note":"The page has no view of the left side: this is the mil-spec forging's, not read on this receiver. BCM's forging reads 0.115 on its own photo (bcm-m4-upper.cam_pad_edge_round)."},"latch_slot_wall":{"label":"The charging handle latch's slot in the left wall: the wall left between it and the notch's front wall (handle_seat_x)","kind":"length","measurements":[{"id":"tdp","value":0.156,"unit":"in","pm":0.005,"stated":".156","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: Section D-D (cut along the notch's centre line, View C-C: the left wall at the rear); user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}}],"note":"The page has no view of the left side: this is the mil-spec forging's, not read on this receiver. As bcm-m4-upper.latch_slot_wall reads the drawing."},"latch_slot_length":{"label":"The latch's slot, along the receiver (its ends full rounds of half this)","kind":"length","measurements":[{"id":"tdp","value":0.195,"unit":"in","pm":0.005,"stated":".195","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: Section D-D (cut along the notch's centre line, View C-C: the left wall at the rear); user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"},"note":"View C-C marks the slot's end FULL R."},{"id":"model","value":0.192,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/batch123/bcm-m4-upper/cad_ch.py): two rounds about z, r 0.0960, at (x 0.329, y 1.616) and (x 0.329, y 1.839), from the wall's face at z -0.318 in to the slot's floor at -0.251; the flat between them from x 0.233 to 0.425","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's callout; the reference model's is within 0.003 of it."},"note":"The page has no view of the left side: this is the mil-spec forging's, not read on this receiver. As bcm-m4-upper.latch_slot_length reads the drawing."},"latch_slot_bottom_y":{"label":"The latch's slot, its lower end above the pin line","kind":"length","measurements":[{"id":"model","value":1.52,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/batch123/bcm-m4-upper/cad_ch.py, as bcm-m4-upper.latch_slot_length records it): two rounds about z, r 0.0960, at (x 0.329, y 1.616) and (x 0.329, y 1.839): the slot from y 1.520 to 1.935","via":"user"}}],"note":"The page has no view of the left side: this is the mil-spec forging's, not read on this receiver. Its heights have no callout in the drawing's View C-C or Section D-D: the reference model's."},"latch_slot_top_y":{"label":"The latch's slot, its upper end above the pin line","kind":"length","measurements":[{"id":"model","value":1.935,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/batch123/bcm-m4-upper/cad_ch.py, as bcm-m4-upper.latch_slot_length records it): two rounds about z, r 0.0960, at (x 0.329, y 1.616) and (x 0.329, y 1.839): the slot from y 1.520 to 1.935","via":"user"}}],"note":"The page has no view of the left side: this is the mil-spec forging's, not read on this receiver. Its heights have no callout in the drawing's View C-C or Section D-D: the reference model's."}}},{"subject":"radian-raptor-charging-handle","title":"Radian Weapons Raptor Ambidextrous Charging Handle AR15/M16, black (R0001)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"wing","value":1.34,"unit":"oz","pm":0.005,"stated":"Weight: 1.34 oz.","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Radian Raptor AR-15 Ambidextrous Charging Handle (MPN: R0001 / R0002 / R0003 / R0004 / R0375), SPECIFICATIONS","url":"https://www.wingtactical.com/firearm-parts-accessories/radian-raptor-ar-15-ambidextrous-charging-handle/","retrieved":"2026-10-06","via":"harvest"},"note":"One figure for every colour the page sells."},{"id":"spicetac","value":1.3,"unit":"oz","pm":0.05,"stated":"\"How much does the Raptor charging handle weigh?\" The answer is 1.3 ounces.","source":{"type":"spec","publisher":"review","name":"SpiceTac, The Ultimate Raptor Charging Handle Review - All Models: the reviewer's own weighing, with the photo of the black Raptor on the scale (1b2e2c0d05fc: the display reads 0:01.3 lb:oz)","url":"https://www.spicetac.com/blog/the-ultimate-raptor-charging-handle-review-all-models/","retrieved":"2026-10-06","via":"harvest"},"note":"A kitchen scale's tenth of an ounce."}],"adopt":{"from":"wing","reason":"The finer figure; the reviewer's scale, read to a tenth of an ounce, agrees with it."},"note":"Radian's own figure wasn't read (its pages are script-drawn). A seller's specification and a reviewer's own scale agree."},"length":{"label":"The shaft: its shoulder (the front face of the ledge under the T's block, where the Army's drawing has the T's front face) to the front hook's tip","kind":"length","measurements":[{"id":"standard","value":5.895,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{aero-charging-handle.length}","via":"harvest"},"note":"US Army TDP drawing 8448518 (Handle, Charging), rev G, side view: 5.600 and .295."}],"note":"The standard's, by expression: no page states a length. \"FOR AR15/M16\" (etched on the shaft in the maker's artwork and in Primary Arms' photos): the hook that pulls the carrier is where the standard's is. Primary Arms' photo from below reads it 5.96 at the shaft's own scale (the plan's check), 1% long, as BCM's handle read by the same method."},"shaft_width":{"label":"The shaft's width","kind":"length","measurements":[{"id":"standard","value":0.4,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{aero-charging-handle.shaft_width}","via":"harvest"},"note":"US Army TDP drawing 8448518, plan view: .400 -B-."}],"note":"The standard's, by expression: the channel it runs in is the standard's. It is the plan photo's scale."},"shaft_thickness":{"label":"The shaft's thickness","kind":"length","measurements":[{"id":"standard","value":0.2985,"unit":"in","pm":0.0035,"source":{"type":"derived","expr":"{aero-charging-handle.shaft_thickness}","via":"harvest"},"note":"US Army TDP drawing 8448518, side view: .2985 ±.0035."}],"note":"The standard's, by expression."},"latch_reach":{"label":"The right-hand latch's reach: its tip off the shaft's right side face, across","kind":"length","measurements":[{"id":"photo","value":1.15,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/radian-raptor-charging-handle 10e25db90367 (Primary Arms: the black R0001 from below, on white, 2200 x 1467)","scaleRef":"the shaft's width column by column (shaft_width)","method":"the traced plan's furthest point to the handle's right, 1.350 off the shaft's centre line, less half the shaft's width; the photo from above (f83c3853e399) has that tip at 1.346","via":"harvest"}}],"note":"No page states one. The two latches differ: \"Note the Raptor's right side handle is extended more than the left to clear the forward assist button.\" (SpiceTac's review, https://www.spicetac.com/blog/the-ultimate-raptor-charging-handle-review-all-models/); the left-hand one's is latch_reach_left."},"latch_reach_left":{"label":"The left-hand latch's reach: its tip off the shaft's left side face, across","kind":"length","measurements":[{"id":"photo","value":1.02,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/radian-raptor-charging-handle 10e25db90367 (Primary Arms: the black R0001 from below, on white, 2200 x 1467)","scaleRef":"the shaft's width column by column (shaft_width)","method":"the traced plan's furthest point to the handle's left, 1.220 off the shaft's centre line, less half the shaft's width; the photo from above (f83c3853e399) has that tip at 1.214","via":"harvest"}}]},"t_width":{"label":"The T, side to side: across the two latches' tips","kind":"length","measurements":[{"id":"spicetac","value":2.567,"unit":"in","pm":0.005,"stated":"2.567\"","source":{"type":"spec","publisher":"review","name":"SpiceTac, The Ultimate Raptor Charging Handle Review - All Models: the figure lettered across the Raptor in its picture 'Radian Raptor vs Standard AR15 Charging Handle' (0e3a1a260cc5: 2.567\" across the Raptor, 2.050\" across the standard handle beside it), with the sentence under it: \"The Raptor charging handle is approx. 0.517\" wider than the original AR15 charging handle.\"","url":"https://www.spicetac.com/blog/the-ultimate-raptor-charging-handle-review-all-models/","retrieved":"2026-10-06","via":"harvest"},"note":"The reviewer's own measurement; with what, the page doesn't say. The ± is its last digit's."},{"id":"photo","value":2.57,"unit":"in","pm":0.037,"source":{"type":"photo","photo":"references/radian-raptor-charging-handle 10e25db90367 (Primary Arms: the black R0001 from below, on white, 2200 x 1467)","scaleRef":"scale from radian-raptor-charging-handle.shaft_width = 0.4 in, the tube's own width column by column: 110.8 px over columns 560–900, 110.6 px over columns 1000–1600, 109.8 px over columns 1820–1950; a line through them (rms 0.17 px) changes -0.8% from column 560 to 1950, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 276.6 px/in there. The axis is the tube's centre line (tilt +0.28°, rms 0.06 px)","method":"height of the traced outline (tools/trace.py); across the two latches' tips (their lower faces' edges)","via":"harvest"}}],"adopt":{"from":"spicetac","reason":"A measurement taken on the part, to a thousandth; Primary Arms' photo from below, scaled by the shaft's own width, reads 2.570: within 0.003 in."},"note":"No seller states it. A reviewer measured it beside a standard handle's (2.050, which is what the catalog's mil-spec handle is: aero-charging-handle.t_width has 2.0 to 2.1), and the plan photo reads the same."},"t_depth":{"label":"The T, front to back: its rear face behind the shoulder","kind":"length","measurements":[{"id":"photo","value":1.053,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/radian-raptor-charging-handle 10e25db90367 (Primary Arms: the black R0001 from below, on white, 2200 x 1467)","scaleRef":"scale from radian-raptor-charging-handle.shaft_width = 0.4 in, the tube's own width column by column: 110.8 px over columns 560–900, 110.6 px over columns 1000–1600, 109.8 px over columns 1820–1950; a line through them (rms 0.17 px) changes -0.8% from column 560 to 1950, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 276.6 px/in there. The axis is the tube's centre line (tilt +0.28°, rms 0.06 px)","method":"−x_min of the traced outline (tools/trace.py); the T's rear face behind the shoulder","via":"harvest"}}]},"latch_height":{"label":"A latch's height: its upper face above its lower face","kind":"length","measurements":[{"id":"photo","value":0.359,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/radian-raptor-charging-handle c6e8b6334675 (Primary Arms: the black R0001 from ahead of its right side and above, on white, 2200 x 1467)","scaleRef":"a camera fitted to the photo (references/radian-raptor-charging-handle/scratch/cam.py: twenty corners of the laser marking on the plane of the shaft's top, each placed in the plan through the photo from above, f83c3853e399; the shaft's lower near edge at the Army drawing's .400 by .2985 section; the hook's rear lower corner at the drawing's 5.600 and .275; one focal length; 1.9 px rms; the lens 18 in from the shoulder; a pixel is 0.0037 in of height at the latch)","method":"seven grooves down the right latch's front face, each one's two ends put on the plan's front edge (z 0.69 to 1.07 off the centre line): 0.340 to 0.373 high, mean 0.359; the plan drawn over the photo at the two heights lies on the latches' upper faces, their windows and the near latch's lower silhouette (scratch/overlay_obl.png)","via":"harvest"}},{"id":"patent","value":0.363,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/radian-raptor-charging-handle c52df6858fe2 (US D694,354 S, 'Firearm charging handle', sheet 4 of 5: FIG. 5 and FIG. 6, the two side views; the patent office's PDF, 2560 x 3300)","scaleRef":"the shaft's own thickness in the same figure (shaft_thickness): its broken lines 134.5 px apart in FIG. 5 (450.6 px/in) and 128 px in FIG. 6 (428.8 px/in)","method":"the latch's box (the claimed design, in solid lines): 164.5 px high in FIG. 5 (0.365) and 155 px in FIG. 6 (0.3615)","via":"harvest"},"note":"FIG. 5 is drawn upside down beside FIG. 6: the shaft's top chamfer is at the page's foot in it."}],"adopt":{"from":"photo","reason":"Read on the product; the design patent's two side views, scaled by the shaft's thickness, give 0.363: within 0.004 in."},"note":"The latches are blocks with upright walls, taller than the shaft is thick. The patent is drawn for this handle (its number is etched on the shaft) and gives the same height as the product's photo."},"latch_lift":{"label":"A latch's lower face above the shaft's underside","kind":"length","measurements":[{"id":"photo","value":0.022,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/radian-raptor-charging-handle c6e8b6334675 (Primary Arms: the black R0001 from ahead of its right side and above, on white, 2200 x 1467)","scaleRef":"a camera fitted to the photo (references/radian-raptor-charging-handle/scratch/cam.py: twenty corners of the laser marking on the plane of the shaft's top, each placed in the plan through the photo from above, f83c3853e399; the shaft's lower near edge at the Army drawing's .400 by .2985 section; the hook's rear lower corner at the drawing's 5.600 and .275; one focal length; 1.9 px rms; the lens 18 in from the shoulder; a pixel is 0.0037 in of height at the latch)","method":"the lower ends of seven grooves down the right latch's front face: 0.115 to 0.146 below the channel's axis (mean 0.127), the shaft's underside being 0.149 below it","via":"harvest"}},{"id":"patent","value":0.024,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/radian-raptor-charging-handle c52df6858fe2 (US D694,354 S, 'Firearm charging handle', sheet 4 of 5: FIG. 5 and FIG. 6, the two side views; the patent office's PDF, 2560 x 3300)","scaleRef":"the shaft's own thickness in the same figure (shaft_thickness): its broken lines 134.5 px apart in FIG. 5 (450.6 px/in) and 128 px in FIG. 6 (428.8 px/in)","method":"the latch's box above the shaft's underside line: 8.5 px in FIG. 5 (0.019) and 12 px in FIG. 6 (0.028)","via":"harvest"}}],"adopt":{"from":"photo","reason":"Read on the product; the design patent's two side views agree within 0.002 in."},"note":"Wing Tactical's photo from behind (5c61726d7baf) has the latches' lower edges level with the lower plate's within what it shows (about 0.02): not told apart from this."},"t_height":{"label":"The T's height: the upper plate's top above the shaft's underside (the lower plate's underside taken as flush with the shaft's, as the patent draws it)","kind":"length","measurements":[{"id":"photo","value":0.4,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/radian-raptor-charging-handle 5c61726d7baf (Wing Tactical: the handle from behind and a little above, its latches Tungsten Grey, 1280 x 1280)","scaleRef":"the latch's own rear face beside it, 184 px high from its upper edge to its lower (latch_height): 512 px/in","method":"the upper plate's rear upper edge (row 654 on columns 560 to 700) stands 10 px above the latches' (row 664 on columns 300 to 380): 0.02 above the latches' upper faces, which are latch_lift + latch_height above the shaft's underside","via":"harvest"},"note":"A same-plane ratio: the plate's rear face and the latches' are taken as one plane (the photo is from close by)."},{"id":"patent","value":0.411,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/radian-raptor-charging-handle c52df6858fe2 (US D694,354 S, 'Firearm charging handle', sheet 4 of 5: FIG. 5 and FIG. 6, the two side views; the patent office's PDF, 2560 x 3300)","scaleRef":"the shaft's own thickness in the same figure (shaft_thickness): its broken lines 134.5 px apart in FIG. 5 (450.6 px/in) and 128 px in FIG. 6 (428.8 px/in)","method":"the broken lines over and under the latch (the T's body): 183 px apart in FIG. 5 (0.406), 177 px in FIG. 6 (0.415), the lower one on the shaft's underside line in both","via":"harvest"},"note":"Broken lines: the patent's environment, not its claim."}],"adopt":{"from":"photo","reason":"A photo of the product; the patent's broken lines give 0.411, within 0.011 in."},"note":"Through the fitted camera the two pins' ends read 0.38 and 0.39 above the shaft's underside in Primary Arms' oblique photo (c6e8b6334675; each 8 px off its place in the plan): they are set in counterbores in the plate, so that is under its top."},"upper_plate_thickness":{"label":"The upper plate's thickness at the T's rear: its top down to the latches' tongues under it","kind":"length","measurements":[{"id":"photo","value":0.176,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/radian-raptor-charging-handle 5c61726d7baf (Wing Tactical: the handle from behind and a little above, its latches Tungsten Grey, 1280 x 1280)","scaleRef":"the latch's own rear face beside it, 184 px high (latch_height): 512 px/in","method":"the upper plate's rear face on columns 560 to 700: its upper edge at row 654, the gap under it at rows 742 to 747 (the latches' tongues from 747 to 806, the lower plate from 812 to 848): 90 px","via":"harvest"},"note":"A same-plane ratio, as t_height's."}],"note":"It is how deep the gap round the plate is drawn: what shows at its foot is the latches' tongues."},"lower_plate_thickness":{"label":"The lower plate's thickness: its top above the shaft's underside. It is the ledge that runs on to the shoulder under the block's front face","kind":"length","measurements":[{"id":"patent","value":0.086,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/radian-raptor-charging-handle c52df6858fe2 (US D694,354 S, 'Firearm charging handle', sheet 4 of 5: FIG. 5 and FIG. 6, the two side views; the patent office's PDF, 2560 x 3300)","scaleRef":"the shaft's own thickness in the same figure (shaft_thickness): its broken lines 134.5 px apart in FIG. 5 (450.6 px/in) and 128 px in FIG. 6 (428.8 px/in)","method":"the lower of the two broken lines along the T's body between the latch and the shoulder, on both sides of the handle: 39 px above the shaft's underside line in FIG. 5 (0.087), 36 px in FIG. 6 (0.084)","via":"harvest"},"note":"Broken lines: the patent's environment, not its claim."},{"id":"photo","value":0.07,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/radian-raptor-charging-handle 5c61726d7baf (Wing Tactical: the handle from behind and a little above, its latches Tungsten Grey, 1280 x 1280)","scaleRef":"the latch's own rear face beside it, 184 px high (latch_height): 512 px/in","method":"the lower plate's rear face on columns 560 to 700: rows 812 to 848, 36 px","via":"harvest"},"note":"At the T's rear, not at the shoulder; a same-plane ratio, as t_height's."}],"adopt":{"from":"patent","reason":"The line that runs to the shoulder, in both of the patent's side views; the lower plate's rear face in Wing Tactical's photo reads 0.07, within the two readings' ±."},"note":"The same line as the hook arm's underside (catch_bottom): the arm lies on it. In BCM's receiver as modelled the notch's cut-back corners stand over the ledge's place (their walls 0.21 to 0.31 off the centre line, at the shaft's upper half only): a ledge this thin goes under them."},"block_front_behind_shoulder":{"label":"The block's front face (where its top, as thick as the shaft, ends over the ledge): how far behind the shoulder","kind":"length","measurements":[{"id":"photo","value":0.112,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/radian-raptor-charging-handle f83c3853e399 (Primary Arms: the black R0001's T from above, on white, 2200 x 1467)","scaleRef":"the two pins' ends, 367.9 px apart for the 0.856 in the plan has between them: 429.9 px/in (it puts the latches' tips 1.346 and 1.214 off the centre line where the plan has 1.350 and 1.220)","method":"the block's top ends at row 600 across columns 990 to 1300, the ledge's front face (the shoulder) at row 648: 48 px","via":"harvest"}}]},"catch_bottom":{"label":"The latch's hook arm (what catches the receiver, on the left): its underside above the shaft's underside","kind":"length","measurements":[{"id":"patent","value":0.086,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/radian-raptor-charging-handle c52df6858fe2 (US D694,354 S, 'Firearm charging handle', sheet 4 of 5: FIG. 5 and FIG. 6, the two side views; the patent office's PDF, 2560 x 3300)","scaleRef":"the shaft's own thickness in the same figure (shaft_thickness): its broken lines 134.5 px apart in FIG. 5 (450.6 px/in) and 128 px in FIG. 6 (428.8 px/in)","method":"the hook's broken box ahead of the latch: its nearer line 39 px from the shaft's underside line in FIG. 5 (0.087), 36 px in FIG. 6 (0.084)","via":"harvest"},"note":"Broken lines: the patent's environment, not its claim."}],"note":"From the patent's broken lines alone: no photo on file is square to the handle's side."},"catch_top":{"label":"The latch's hook arm: its top above the shaft's underside","kind":"length","measurements":[{"id":"patent","value":0.217,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/radian-raptor-charging-handle c52df6858fe2 (US D694,354 S, 'Firearm charging handle', sheet 4 of 5: FIG. 5 and FIG. 6, the two side views; the patent office's PDF, 2560 x 3300)","scaleRef":"the shaft's own thickness in the same figure (shaft_thickness): its broken lines 134.5 px apart in FIG. 5 (450.6 px/in) and 128 px in FIG. 6 (428.8 px/in)","method":"the hook's broken box ahead of the latch: its further line 97 px from the shaft's underside line in FIG. 5 (0.215), 94 px in FIG. 6 (0.219)","via":"harvest"},"note":"Broken lines: the patent's environment, not its claim."}]},"top_flat_width":{"label":"The flat along the shaft's top, between its two chamfers","kind":"length","measurements":[{"id":"photo","value":0.205,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/radian-raptor-charging-handle f83c3853e399 (Primary Arms: the black R0001's T from above, on white, 2200 x 1467)","scaleRef":"the shaft's own width there, 168 px (shaft_width)","method":"rows 840 to 900, ahead of the chamfers' run-out and behind the marking: the lit left chamfer is columns 1054 to 1094 (40 px), the right one's edge shows at column 1180 (42 px to the shaft's edge at 1222): 86 px between them","via":"harvest"}}],"note":"Wider than the Army's (.15, 8448518 Section A-A): the marking is on it. The maker's artwork (98d9604cc97f) has the three bands 21, 39 and 21 px of the shaft's 82: 0.19."},"top_chamfer_drop":{"label":"The shaft's top chamfers: how far below the top their lower edges are","kind":"length","measurements":[{"id":"patent","value":0.06,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/radian-raptor-charging-handle c52df6858fe2 (US D694,354 S, 'Firearm charging handle', sheet 4 of 5: FIG. 5 and FIG. 6, the two side views; the patent office's PDF, 2560 x 3300)","scaleRef":"the shaft's own thickness in the same figure (shaft_thickness): its broken lines 134.5 px apart in FIG. 5 (450.6 px/in) and 128 px in FIG. 6 (428.8 px/in)","method":"the broken line under the shaft's top line, ahead of the run-out: 27 px below it in FIG. 5 (0.0599), 25.5 px in FIG. 6 (0.0595)","via":"harvest"},"note":"Broken lines: the patent's environment, not its claim."}],"note":"With top_flat_width that is a chamfer at 31.6 degrees; the Army's drawing has 30."},"top_chamfer_from_shoulder":{"label":"The shaft's top chamfers: where they begin, ahead of the shoulder","kind":"length","measurements":[{"id":"photo","value":0.226,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/radian-raptor-charging-handle f83c3853e399 (Primary Arms: the black R0001's T from above, on white, 2200 x 1467)","scaleRef":"the two pins' ends, 367.9 px apart for the 0.856 in the plan has between them: 429.9 px/in (it puts the latches' tips 1.346 and 1.214 off the centre line where the plan has 1.350 and 1.220)","method":"the left chamfer's lit band first shows at row 745 (± 5), the shoulder being at row 648","via":"harvest"}}],"note":"The Army's drawing has .235 ±.015 (8448518, the plan view), with a .25 R run-out."},"top_chamfer_full_from_shoulder":{"label":"The shaft's top chamfers: where they have reached their full width, ahead of the shoulder","kind":"length","measurements":[{"id":"photo","value":0.377,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/radian-raptor-charging-handle f83c3853e399 (Primary Arms: the black R0001's T from above, on white, 2200 x 1467)","scaleRef":"the two pins' ends, 367.9 px apart for the 0.856 in the plan has between them: 429.9 px/in (it puts the latches' tips 1.346 and 1.214 off the centre line where the plan has 1.350 and 1.220)","method":"the left chamfer's lit band reaches its full 40 px at row 810 (± 5), the shoulder being at row 648","via":"harvest"}}]},"channel_width":{"label":"The key's channel under the shaft: its width","kind":"length","measurements":[{"id":"standard","value":0.312,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-mk2-charging-handle.channel_width}","via":"harvest"},"note":"US Army TDP drawing 8448518 (Handle, Charging), rev G, Section A-A: .312, with FULL R."}]},"channel_depth":{"label":"The key's channel: its depth from the shaft's underside to the top of its round roof","kind":"length","measurements":[{"id":"standard","value":0.25,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-mk2-charging-handle.channel_depth}","via":"harvest"},"note":"US Army TDP drawing 8448518, Section A-A: .250."}]},"hook_length":{"label":"The front hook: its rear face to its tip","kind":"length","measurements":[{"id":"standard","value":0.295,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-mk2-charging-handle.hook_length}","via":"harvest"},"note":"US Army TDP drawing 8448518, side view: .295."}]},"hook_drop":{"label":"The front hook: how far it hangs below the shaft's underside","kind":"length","measurements":[{"id":"standard","value":0.275,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-mk2-charging-handle.hook_drop}","via":"harvest"},"note":"US Army TDP drawing 8448518, side view: .275 -C-."}]},"hook_fillet_r":{"label":"The front hook: the round between its rear face and the shaft's underside","kind":"length","measurements":[{"id":"standard","value":0.187,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-mk2-charging-handle.hook_fillet_r}","via":"harvest"},"note":"US Army TDP drawing 8448518, side view: .187 R."}]},"guide_lug_width":{"label":"Across the two guide lugs near the shaft's front end","kind":"length","measurements":[{"id":"standard","value":0.488,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-mk2-charging-handle.guide_lug_width}","via":"harvest"},"note":"US Army TDP drawing 8448518, end view: .488."}]},"guide_lug_height":{"label":"The guide lugs' height, from the shaft's underside up","kind":"length","measurements":[{"id":"standard","value":0.119,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{bcm-mk2-charging-handle.guide_lug_height}","via":"harvest"},"note":"US Army TDP drawing 8448518, end view: .119 ±.002."}]},"channel_rear_behind_shoulder":{"label":"The key's channel: how far behind the shoulder its round rear end reaches, under the T's block","kind":"length","measurements":[{"id":"photo","value":0.171,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/radian-raptor-charging-handle 10e25db90367 (Primary Arms: the black R0001 from below, on white, 2200 x 1467)","scaleRef":"the shaft's width column by column (shaft_width): 277.7 px/in there","method":"the channel's round end at column 375 (± 3) on the shaft's centre line, the shoulder being at column 422.5","via":"harvest"}}]},"pin_d":{"label":"The latches' pivot pins: their ends' diameter","kind":"length","measurements":[{"id":"photo","value":0.06,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/radian-raptor-charging-handle f83c3853e399 (Primary Arms: the black R0001's T from above, on white, 2200 x 1467)","scaleRef":"the two pins' ends, 367.9 px apart for the 0.856 in the plan has between them: 429.9 px/in (it puts the latches' tips 1.346 and 1.214 off the centre line where the plan has 1.350 and 1.220)","method":"each pin's bright ring is 26 px across at its outside (columns 939 to 966 on the handle's right one)","via":"harvest"}}],"note":"\"oversized roll pins\" (SpiceTac's review): each end shows as a bright ring in a dark counterbore about 0.1 in across."},"rear_groove_count":{"label":"The round grooves down each latch's rear face: how many","kind":"count","measurements":[{"id":"photo","value":5,"unit":"count","source":{"type":"photo","photo":"references/radian-raptor-charging-handle f83c3853e399 (Primary Arms: the black R0001's T from above, on white, 2200 x 1467)","scaleRef":"none: a count","method":"the bays along each latch's rear edge, at 8x: five on the right latch, five on the left; Wing Tactical's photo from behind (5c61726d7baf) shows five grooves on each rear face","via":"harvest"}}],"note":"Counted on two views that show the whole face: five bays along each latch's rear edge from above, five grooves on each rear face from behind."},"rear_groove_pitch":{"label":"The grooves down each latch's rear face: their pitch along the edge","kind":"length","measurements":[{"id":"photo","value":0.083,"unit":"in","pm":0.003,"source":{"type":"photo","photo":"references/radian-raptor-charging-handle f83c3853e399 (Primary Arms: the black R0001's T from above, on white, 2200 x 1467)","scaleRef":"the two pins' ends, 367.9 px apart for the 0.856 in the plan has between them: 429.9 px/in (it puts the latches' tips 1.346 and 1.214 off the centre line where the plan has 1.350 and 1.220)","method":"the five bays' deepest points on each latch: eight spacings, 0.080 to 0.086, mean 0.0831","via":"harvest"}}]},"rear_groove_r":{"label":"The grooves down each latch's rear face: their radius","kind":"length","measurements":[{"id":"photo","value":0.03,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/radian-raptor-charging-handle f83c3853e399 (Primary Arms: the black R0001's T from above, on white, 2200 x 1467)","scaleRef":"the two pins' ends, 367.9 px apart for the 0.856 in the plan has between them: 429.9 px/in (it puts the latches' tips 1.346 and 1.214 off the centre line where the plan has 1.350 and 1.220)","method":"a bay between two teeth's tips: 25 px across at the tips' line and 9.2 px deep, a round of 13 px","via":"harvest"}}]},"rear_groove_depth":{"label":"The grooves down each latch's rear face: their depth from the teeth's tips","kind":"length","measurements":[{"id":"photo","value":0.021,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/radian-raptor-charging-handle f83c3853e399 (Primary Arms: the black R0001's T from above, on white, 2200 x 1467)","scaleRef":"the two pins' ends, 367.9 px apart for the 0.856 in the plan has between them: 429.9 px/in (it puts the latches' tips 1.346 and 1.214 off the centre line where the plan has 1.350 and 1.220)","method":"a bay's deepest point from the line through the two teeth's tips beside it: 9.2 px","via":"harvest"}}]}}},{"subject":"radian-raptor-lt-charging-handle","title":"Radian Weapons Raptor-LT Ambidextrous Charging Handle AR-15 / M16, black (R0148)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"spicetac","value":1.2,"unit":"oz","pm":0.05,"stated":"\"How much does the Raptor LT charging handle weigh?\" The answer is 1.2 ounces.","source":{"type":"spec","publisher":"review","name":"SpiceTac, The Ultimate Raptor Charging Handle Review - All Models: the reviewer's own weighing (David Blazek, of SpiceTac, a seller), with the photo of the black Raptor-LT on the scale (87793f6f6db2: the display reads 0:01.2 lb:oz)","url":"https://www.spicetac.com/blog/the-ultimate-raptor-charging-handle-review-all-models/","retrieved":"2026-10-12","via":"harvest"},"note":"A kitchen scale's tenth of an ounce. The same page: \"it does weigh less than the original Raptor by 0.1 oz (1.2 oz vs 1.3 oz)\"."},{"id":"bereli","value":1.2,"unit":"oz","pm":0.05,"stated":"Weight: Approx. 1.2 oz (0.075 lbs)","source":{"type":"spec","publisher":"retailer","name":"Bereli, Radian Weapons Raptor-LT Ambidextrous Charging Handle for AR15/M16 (R0148) - Black, Specifications","url":"https://www.bereli.com/r0148/","retrieved":"2026-10-12","via":"harvest"},"note":"A seller's \"Approx.\": the reviewer's figure to the digit, and not known to be a second weighing. The same list's \"Dimensions: 7.25\\\" (L) x 3.25\\\" (W) x 0.5\\\" (H)\" is no size of the handle (it is 6.96 long and 2.57 wide by its photos): a package's, or rounded."},{"id":"ar15discounts","value":0.19,"unit":"oz","pm":0.005,"stated":"Weight 0.19 oz","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, Radian Raptor-LT Ambidextrous Charging Handle, Additional information","url":"https://ar15discounts.com/products/radian-raptor-lt-ambidextrous-charging-handle-556-black/","retrieved":"2026-10-12","via":"harvest"},"note":"A shop's weight field, beside \"Dimensions N/A\": a fifth of what the handle's aluminium alone weighs. Not the handle's weight."},{"id":"bigtex","value":4.797,"unit":"oz","pm":0.0005,"stated":"Weight 4.7972588293734 oz Dimensions 8 × 3 × 1 in","source":{"type":"spec","publisher":"retailer","name":"Big Tex Ordnance, Radian RAPTOR-LT AMBIDEXTROUS CHARGING HANDLE, Additional information","url":"https://www.bigtexordnance.com/product/radian-raptor-lt-ambidextrous-charging-handle/","retrieved":"2026-10-12","via":"harvest"},"note":"A shipping record's figure (0.136 kg, with a carton's 8 by 3 by 1 in), for a record that lists every Raptor's colours: the parcel, not the handle."}],"adopt":{"from":"spicetac","reason":"The one weighing of the handle itself, with its photo. Bereli's figure repeats it; AR15Discounts' 0.19 oz and Big Tex Ordnance's 4.797 oz are shops' record fields (the second a parcel's, with a carton's size beside it), and the model's own aluminium and polymer say which is the handle's (its aluminium alone comes to 0.96 oz, all of it as aluminium to 1.48: the part's test holds the four figures to that)."},"note":"No maker's figure was read (Radian's pages are script-drawn). One reviewer, who sells the handle, put it on a scale; a seller's specification repeats his figure. Two shops' weight fields are their own records' and not the handle's: they stay here beside it."},"length":{"label":"The shaft: its shoulder (the front face of the ledge under the T's block) to the front hook's tip","kind":"length","measurements":[{"id":"raptor","value":5.895,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{radian-raptor-charging-handle.length}","via":"harvest"},"note":"US Army TDP drawing 8448518 (Handle, Charging), rev G, side view: 5.600 and .295, as the Raptor's ledger has it."}],"note":"The standard's, through the Raptor's ledger: no page states a length. \"FOR AR15/M16\" is etched on the LT's own shaft (Wing Tactical's close-up of its nose, 6cdc25a7e2eb; Primary Arms' R0148_00, a2724ae397a9), and the hook that pulls the carrier is where the standard's is. The LT's own photo from below reads it 5.97 at the shaft's own scale (the plan's check), 1% long, as the Raptor's and BCM's handles read by the same method."},"shaft_width":{"label":"The shaft's width","kind":"length","measurements":[{"id":"raptor","value":0.4,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{radian-raptor-charging-handle.shaft_width}","via":"harvest"},"note":"US Army TDP drawing 8448518, plan view: .400 -B-."}],"note":"The standard's, through the Raptor's ledger: the channel it runs in is the standard's (\"FOR AR15/M16\" on its shaft). It is the plan photo's scale; the photo's own check of that scale is the two guide lugs, which read the drawing's .488 across."},"shaft_thickness":{"label":"The shaft's thickness","kind":"length","measurements":[{"id":"raptor","value":0.2985,"unit":"in","pm":0.0035,"source":{"type":"derived","expr":"{radian-raptor-charging-handle.shaft_thickness}","via":"harvest"},"note":"US Army TDP drawing 8448518, side view: .2985 ±.0035."}],"note":"The standard's, through the Raptor's ledger."},"latch_reach":{"label":"The right-hand handle's reach: its tip off the shaft's right side face, across","kind":"length","measurements":[{"id":"photo","value":1.148,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/radian-raptor-lt-charging-handle 9a677043deaa (Primary Arms: the black R0148 from below, on white, 2200 x 1467)","scaleRef":"the shaft's width column by column (shaft_width)","method":"the traced plan's furthest point to the handle's right, 1.348 off the shaft's centre line, less half the shaft's width; the photo from above (5d168cd4d6e1) has that tip at 1.356","via":"harvest"}}],"note":"No page states one. The two handles differ as the Raptor's latches do (\"Note the Raptor's right side handle is extended more than the left to clear the forward assist button.\", SpiceTac's review, of the Raptor); the left-hand one's is latch_reach_left. The Raptor's reads 1.15 by the same method: the polymer adds nothing to the reach."},"latch_reach_left":{"label":"The left-hand handle's reach: its tip off the shaft's left side face, across","kind":"length","measurements":[{"id":"photo","value":1.024,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/radian-raptor-lt-charging-handle 9a677043deaa (Primary Arms: the black R0148 from below, on white, 2200 x 1467)","scaleRef":"the shaft's width column by column (shaft_width)","method":"the traced plan's furthest point to the handle's left, 1.224 off the shaft's centre line, less half the shaft's width; the photo from above (5d168cd4d6e1) has that tip at 1.231","via":"harvest"}}]},"t_width":{"label":"The T, side to side: across the two handles' tips","kind":"length","measurements":[{"id":"photo","value":2.573,"unit":"in","pm":0.038,"source":{"type":"photo","photo":"references/radian-raptor-lt-charging-handle 9a677043deaa (Primary Arms: the black R0148 from below, on white, 2200 x 1467)","scaleRef":"scale from radian-raptor-lt-charging-handle.shaft_width = 0.4 in, the tube's own width column by column: 110.6 px over columns 560–900, 110.8 px over columns 1000–1600, 110.0 px over columns 1830–1960; a line through them (rms 0.27 px) changes -0.3% from column 560 to 1960, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 276.7 px/in there. The axis is the tube's centre line (tilt +0.02°, rms 0.15 px)","method":"height of the traced outline (tools/trace.py); across the two handles' tips (their lower faces' edges)","via":"harvest"}}]},"t_depth":{"label":"The T, front to back: its rear face behind the shoulder","kind":"length","measurements":[{"id":"photo","value":1.059,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/radian-raptor-lt-charging-handle 9a677043deaa (Primary Arms: the black R0148 from below, on white, 2200 x 1467)","scaleRef":"scale from radian-raptor-lt-charging-handle.shaft_width = 0.4 in, the tube's own width column by column: 110.6 px over columns 560–900, 110.8 px over columns 1000–1600, 110.0 px over columns 1830–1960; a line through them (rms 0.27 px) changes -0.3% from column 560 to 1960, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 276.7 px/in there. The axis is the tube's centre line (tilt +0.02°, rms 0.15 px)","method":"−x_min of the traced outline (tools/trace.py); the T's rear face behind the shoulder, at the lower faces' edges","via":"harvest"}},{"id":"top","value":1.084,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/radian-raptor-lt-charging-handle 5d168cd4d6e1 (Primary Arms: the black R0148's T from above, on white, 2200 x 1467)","scaleRef":"the two pins' ends, 357.2 px apart for the 0.859 in the plan has between them: 415.9 px/in; placed in the plan by the two pins","method":"the T's rear between the handles: the first dark row of the photo (161) across columns 911 to 945 and on","via":"harvest"},"note":"The upper plate's rear edge, from above; the plan has the lower faces' edges, from below."}],"adopt":{"from":"photo","reason":"The plan the model is built from, at the photo's own scale. The photo from above, placed by the pins, has the T's rear 0.025 further back: inside the two readings' ±, and kept."}},"latch_height":{"label":"A handle's height: its upper face above its lower face","kind":"length","measurements":[{"id":"photo","value":0.37,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/radian-raptor-lt-charging-handle a2724ae397a9 (Primary Arms: the black R0148 from ahead of its right side and above, on white, 2200 x 1467)","scaleRef":"a camera fitted to the photo (references/radian-raptor-lt-charging-handle/scratch/cam.py: 33 marks of the laser marking on the plane of the shaft's top, the centroids of nine letters and of the logo's two pieces and of each one's quarter nearest either side, each placed in the plan through the photo from above, 5d168cd4d6e1; the shaft's lower near edge at the Army drawing's .400 by .2985 section; the hook's rear lower corner at the drawing's 5.600 and .275; one focal length; 0.8 px rms; the lens 19 in from the shoulder and 29 degrees above the handle; a pixel is 0.0036 in of height at the handle)","method":"the near handle's front face unwrapped through the camera (scratch/heights.py, heights3.py: upright lines through 145 points along the plan's front edge, sampled in the photo): the white ground begins at 0.096 below the channel's axis (quartiles 0.092 to 0.100), the grooves down the face read darker than the ribs between them up to 0.236 above it, and the lit top face's rim runs from there to the panel's edge 0.125 higher in the strip, for 0.099 across in the photo from above seen from 29 degrees: the face's upper edge is broken by about 0.023, the upper face 0.268 above the axis. The ± is that edge break, and 0.02 for the handle turned a little on its pin (the strip taken 0.03 either side of the plan's edge moves both edges 0.03 together)","via":"harvest"}}],"note":"The polymer handles are blocks with upright walls, taller than the shaft is thick; their upper faces come out about level with the upper plate's top (0.415 over the shaft's underside by this and latch_lift, the plate's 0.40), as Wing Tactical's close-up from behind has them (3231df18cd03). The Raptor's aluminium latches read 0.359 by its own fitted camera: the same within the two readings' ±. A second reading through the same camera, the handle's silhouette against the edges of its two faces, came out 0.30 and is not kept: its edges are toothed, and it changes by a third of a pixel for a hundredth of an inch."},"latch_lift":{"label":"A handle's lower face above the shaft's underside","kind":"length","measurements":[{"id":"photo","value":0.045,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/radian-raptor-lt-charging-handle a2724ae397a9 (Primary Arms: the black R0148 from ahead of its right side and above, on white, 2200 x 1467)","scaleRef":"a camera fitted to the photo (references/radian-raptor-lt-charging-handle/scratch/cam.py: 33 marks of the laser marking on the plane of the shaft's top, the centroids of nine letters and of the logo's two pieces and of each one's quarter nearest either side, each placed in the plan through the photo from above, 5d168cd4d6e1; the shaft's lower near edge at the Army drawing's .400 by .2985 section; the hook's rear lower corner at the drawing's 5.600 and .275; one focal length; 0.8 px rms; the lens 19 in from the shoulder and 29 degrees above the handle; a pixel is 0.0036 in of height at the handle)","method":"the near handle's lower edge against the white ground, through the camera: 0.096 below the channel's axis along its front face (145 upright lines, quartiles 0.092 to 0.100) and 0.122 round its tip (0.104 to 0.128); between the two, 0.105, the shaft's underside being 0.149 below the axis","via":"harvest"}}],"note":"The handles' lower faces stand above the shaft's underside. The Raptor's reads 0.022 by its own camera."},"panel_depth":{"label":"The panel sunk in each handle's upper face: how far its floor is below the face","kind":"length","measurements":[{"id":"photo","value":0.075,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/radian-raptor-lt-charging-handle aab96ff5153e (Wing Tactical: a Flat Dark Earth one in a rifle, from behind and a little above and to the left, 1280 x 1280)","scaleRef":"the left handle's own height in the same view, its upper face's rear edge to its lower edge beside the ribs: 115 px for latch_height","method":"the panel's far wall, lit, from its rim to the floor: 24 px (rows 548 to 572 at columns 300 to 400); a same-distance ratio, the lens about 15 degrees above the handle","via":"harvest"},"note":"A lower bound if the near rim hides the wall's foot: the floor shows in the photo, so taken as the depth."}],"note":"The panel in each upper face is a deep one (the handles' cores have openings under them: Wing Tactical's x-ray banner); the one in each lower face is shallow and isn't measured. Through the fitted camera the wall's shadow in Primary Arms' oblique photo reads 0.06 to 0.15 by where the rim is taken to be: no better."},"t_height":{"label":"The T's height: the upper plate's top above the shaft's underside","kind":"length","measurements":[{"id":"raptor","value":0.4,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{radian-raptor-charging-handle.t_height}","via":"harvest"},"note":"The Raptor's, read on Wing Tactical's photo of that handle from behind and on its design patent's two side views (D694,354, the number etched on the LT's shaft too)."}],"note":"The T's aluminium body is the Raptor's: T.REX ARMS' page for the family says of the LT: \"Same as the Standard but features aluminum latches over-molded with high-strength reinforced polymer.\" (https://www.trex-arms.com/store/Radian-Weapons-Raptor-Charging-Handle/), and the Raptor's upper plate, the arc at its front and its block, carried by the two pivot pins, lie on the LT's own in Primary Arms' photo of it from above (5d168cd4d6e1; references/radian-raptor-lt-charging-handle/scratch/xfer_L.png), within 2 px of 416 to the inch. No photo of the LT is square to its side; Wing Tactical's close-up of the grey one from behind (3231df18cd03) shows the same stack between the handles: an upper plate, the two tongues, a lower plate."},"upper_plate_thickness":{"label":"The upper plate's thickness at the T's rear: its top down to the handles' tongues under it","kind":"length","measurements":[{"id":"raptor","value":0.176,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{radian-raptor-charging-handle.upper_plate_thickness}","via":"harvest"},"note":"The Raptor's, a same-plane ratio on Wing Tactical's photo of that handle from behind."}],"note":"The T's aluminium body is the Raptor's: T.REX ARMS' page for the family says of the LT: \"Same as the Standard but features aluminum latches over-molded with high-strength reinforced polymer.\" (https://www.trex-arms.com/store/Radian-Weapons-Raptor-Charging-Handle/), and the Raptor's upper plate, the arc at its front and its block, carried by the two pivot pins, lie on the LT's own in Primary Arms' photo of it from above (5d168cd4d6e1; references/radian-raptor-lt-charging-handle/scratch/xfer_L.png), within 2 px of 416 to the inch. "},"lower_plate_thickness":{"label":"The lower plate's thickness: its top above the shaft's underside. It is the ledge that runs on to the shoulder under the block's front face","kind":"length","measurements":[{"id":"raptor","value":0.086,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{radian-raptor-charging-handle.lower_plate_thickness}","via":"harvest"},"note":"The Raptor's, from its design patent's two side views."}],"note":"The T's aluminium body is the Raptor's: T.REX ARMS' page for the family says of the LT: \"Same as the Standard but features aluminum latches over-molded with high-strength reinforced polymer.\" (https://www.trex-arms.com/store/Radian-Weapons-Raptor-Charging-Handle/), and the Raptor's upper plate, the arc at its front and its block, carried by the two pivot pins, lie on the LT's own in Primary Arms' photo of it from above (5d168cd4d6e1; references/radian-raptor-lt-charging-handle/scratch/xfer_L.png), within 2 px of 416 to the inch. "},"block_front_behind_shoulder":{"label":"The block's front face (where its top, as thick as the shaft, ends over the ledge): how far behind the shoulder","kind":"length","measurements":[{"id":"raptor","value":0.112,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{radian-raptor-charging-handle.block_front_behind_shoulder}","via":"harvest"},"note":"The Raptor's, read on Primary Arms' photo of that handle from above."}],"note":"The T's aluminium body is the Raptor's: T.REX ARMS' page for the family says of the LT: \"Same as the Standard but features aluminum latches over-molded with high-strength reinforced polymer.\" (https://www.trex-arms.com/store/Radian-Weapons-Raptor-Charging-Handle/), and the Raptor's upper plate, the arc at its front and its block, carried by the two pivot pins, lie on the LT's own in Primary Arms' photo of it from above (5d168cd4d6e1; references/radian-raptor-lt-charging-handle/scratch/xfer_L.png), within 2 px of 416 to the inch. The LT's own photo from above shows the same step: the shadowed band between the block's top and the ledge's front edge is 31 px there (rows 573 to 604 beside the shaft: 0.075 in at 415.9 px/in), and 33 px in the Raptor's photo taken the same way (0.077 at 429.9): the Raptor's own figure counts the block's edge break and the ledge's soft edge with it (rows 600 to 648)."},"catch_bottom":{"label":"The latch's hook arm (what catches the receiver, on the left): its underside above the shaft's underside","kind":"length","measurements":[{"id":"raptor","value":0.086,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{radian-raptor-charging-handle.catch_bottom}","via":"harvest"},"note":"The Raptor's, from its design patent's broken lines."}],"note":"The T's aluminium body is the Raptor's: T.REX ARMS' page for the family says of the LT: \"Same as the Standard but features aluminum latches over-molded with high-strength reinforced polymer.\" (https://www.trex-arms.com/store/Radian-Weapons-Raptor-Charging-Handle/), and the Raptor's upper plate, the arc at its front and its block, carried by the two pivot pins, lie on the LT's own in Primary Arms' photo of it from above (5d168cd4d6e1; references/radian-raptor-lt-charging-handle/scratch/xfer_L.png), within 2 px of 416 to the inch. On the LT the hook arm is the left handle's aluminium core, bare of polymer and black (Primary Arms' R0149_03)."},"catch_top":{"label":"The latch's hook arm: its top above the shaft's underside","kind":"length","measurements":[{"id":"raptor","value":0.217,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{radian-raptor-charging-handle.catch_top}","via":"harvest"},"note":"The Raptor's, from its design patent's broken lines."}],"note":"The T's aluminium body is the Raptor's: T.REX ARMS' page for the family says of the LT: \"Same as the Standard but features aluminum latches over-molded with high-strength reinforced polymer.\" (https://www.trex-arms.com/store/Radian-Weapons-Raptor-Charging-Handle/), and the Raptor's upper plate, the arc at its front and its block, carried by the two pivot pins, lie on the LT's own in Primary Arms' photo of it from above (5d168cd4d6e1; references/radian-raptor-lt-charging-handle/scratch/xfer_L.png), within 2 px of 416 to the inch. "},"top_flat_width":{"label":"The flat along the shaft's top, between its two chamfers","kind":"length","measurements":[{"id":"raptor","value":0.205,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{radian-raptor-charging-handle.top_flat_width}","via":"harvest"},"note":"The Raptor's, read on Primary Arms' photo of that handle from above."}],"note":"The T's aluminium body is the Raptor's: T.REX ARMS' page for the family says of the LT: \"Same as the Standard but features aluminum latches over-molded with high-strength reinforced polymer.\" (https://www.trex-arms.com/store/Radian-Weapons-Raptor-Charging-Handle/), and the Raptor's upper plate, the arc at its front and its block, carried by the two pivot pins, lie on the LT's own in Primary Arms' photo of it from above (5d168cd4d6e1; references/radian-raptor-lt-charging-handle/scratch/xfer_L.png), within 2 px of 416 to the inch. The LT's marking is on the same flat (RADIAN RAPTOR-LT, the patents' numbers, FOR AR15/M16)."},"top_chamfer_drop":{"label":"The shaft's top chamfers: how far below the top their lower edges are","kind":"length","measurements":[{"id":"raptor","value":0.06,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{radian-raptor-charging-handle.top_chamfer_drop}","via":"harvest"},"note":"The Raptor's, from its design patent's side views."}],"note":"The T's aluminium body is the Raptor's: T.REX ARMS' page for the family says of the LT: \"Same as the Standard but features aluminum latches over-molded with high-strength reinforced polymer.\" (https://www.trex-arms.com/store/Radian-Weapons-Raptor-Charging-Handle/), and the Raptor's upper plate, the arc at its front and its block, carried by the two pivot pins, lie on the LT's own in Primary Arms' photo of it from above (5d168cd4d6e1; references/radian-raptor-lt-charging-handle/scratch/xfer_L.png), within 2 px of 416 to the inch. "},"top_chamfer_from_shoulder":{"label":"The shaft's top chamfers: where they begin, ahead of the shoulder","kind":"length","measurements":[{"id":"raptor","value":0.226,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{radian-raptor-charging-handle.top_chamfer_from_shoulder}","via":"harvest"},"note":"The Raptor's, read on Primary Arms' photo of that handle from above."}],"note":"The T's aluminium body is the Raptor's: T.REX ARMS' page for the family says of the LT: \"Same as the Standard but features aluminum latches over-molded with high-strength reinforced polymer.\" (https://www.trex-arms.com/store/Radian-Weapons-Raptor-Charging-Handle/), and the Raptor's upper plate, the arc at its front and its block, carried by the two pivot pins, lie on the LT's own in Primary Arms' photo of it from above (5d168cd4d6e1; references/radian-raptor-lt-charging-handle/scratch/xfer_L.png), within 2 px of 416 to the inch. In the LT's photo from above the chamfers come in over the same stretch (their lit band first shows about row 700, 0.23 ahead of the ledge's front edge)."},"top_chamfer_full_from_shoulder":{"label":"The shaft's top chamfers: where they have reached their full width, ahead of the shoulder","kind":"length","measurements":[{"id":"raptor","value":0.377,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{radian-raptor-charging-handle.top_chamfer_full_from_shoulder}","via":"harvest"},"note":"The Raptor's, read on Primary Arms' photo of that handle from above."}],"note":"The T's aluminium body is the Raptor's: T.REX ARMS' page for the family says of the LT: \"Same as the Standard but features aluminum latches over-molded with high-strength reinforced polymer.\" (https://www.trex-arms.com/store/Radian-Weapons-Raptor-Charging-Handle/), and the Raptor's upper plate, the arc at its front and its block, carried by the two pivot pins, lie on the LT's own in Primary Arms' photo of it from above (5d168cd4d6e1; references/radian-raptor-lt-charging-handle/scratch/xfer_L.png), within 2 px of 416 to the inch. "},"channel_width":{"label":"The key's channel under the shaft: its width","kind":"length","measurements":[{"id":"raptor","value":0.312,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{radian-raptor-charging-handle.channel_width}","via":"harvest"},"note":"US Army TDP drawing 8448518 (Handle, Charging), rev G, Section A-A: .312, with FULL R."}],"note":"The standard's, through the Raptor's ledger: the shaft is made to run in the standard channel and pull the standard carrier (\"FOR AR15/M16\" on it), and Primary Arms' photo of the LT from below shows the key's channel, the two guide lugs and the hook's block where the drawing has them."},"channel_depth":{"label":"The key's channel: its depth from the shaft's underside to the top of its round roof","kind":"length","measurements":[{"id":"raptor","value":0.25,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{radian-raptor-charging-handle.channel_depth}","via":"harvest"},"note":"US Army TDP drawing 8448518, Section A-A: .250."}],"note":"The standard's, through the Raptor's ledger: the shaft is made to run in the standard channel and pull the standard carrier (\"FOR AR15/M16\" on it), and Primary Arms' photo of the LT from below shows the key's channel, the two guide lugs and the hook's block where the drawing has them."},"hook_length":{"label":"The front hook: its rear face to its tip","kind":"length","measurements":[{"id":"raptor","value":0.295,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{radian-raptor-charging-handle.hook_length}","via":"harvest"},"note":"US Army TDP drawing 8448518, side view: .295."}],"note":"The standard's, through the Raptor's ledger: the shaft is made to run in the standard channel and pull the standard carrier (\"FOR AR15/M16\" on it), and Primary Arms' photo of the LT from below shows the key's channel, the two guide lugs and the hook's block where the drawing has them."},"hook_drop":{"label":"The front hook: how far it hangs below the shaft's underside","kind":"length","measurements":[{"id":"raptor","value":0.275,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{radian-raptor-charging-handle.hook_drop}","via":"harvest"},"note":"US Army TDP drawing 8448518, side view: .275 -C-."}],"note":"The standard's, through the Raptor's ledger: the shaft is made to run in the standard channel and pull the standard carrier (\"FOR AR15/M16\" on it), and Primary Arms' photo of the LT from below shows the key's channel, the two guide lugs and the hook's block where the drawing has them."},"hook_fillet_r":{"label":"The front hook: the round between its rear face and the shaft's underside","kind":"length","measurements":[{"id":"raptor","value":0.187,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{radian-raptor-charging-handle.hook_fillet_r}","via":"harvest"},"note":"US Army TDP drawing 8448518, side view: .187 R."}],"note":"The standard's, through the Raptor's ledger: the shaft is made to run in the standard channel and pull the standard carrier (\"FOR AR15/M16\" on it), and Primary Arms' photo of the LT from below shows the key's channel, the two guide lugs and the hook's block where the drawing has them."},"guide_lug_width":{"label":"Across the two guide lugs near the shaft's front end","kind":"length","measurements":[{"id":"raptor","value":0.488,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{radian-raptor-charging-handle.guide_lug_width}","via":"harvest"},"note":"US Army TDP drawing 8448518, end view: .488."}],"note":"The standard's, through the Raptor's ledger: the shaft is made to run in the standard channel and pull the standard carrier (\"FOR AR15/M16\" on it), and Primary Arms' photo of the LT from below shows the key's channel, the two guide lugs and the hook's block where the drawing has them. The LT's plan reads them at that width (the trace's check)."},"guide_lug_height":{"label":"The guide lugs' height, from the shaft's underside up","kind":"length","measurements":[{"id":"raptor","value":0.119,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{radian-raptor-charging-handle.guide_lug_height}","via":"harvest"},"note":"US Army TDP drawing 8448518, end view: .119 ±.002."}],"note":"The standard's, through the Raptor's ledger: the shaft is made to run in the standard channel and pull the standard carrier (\"FOR AR15/M16\" on it), and Primary Arms' photo of the LT from below shows the key's channel, the two guide lugs and the hook's block where the drawing has them."},"channel_rear_behind_shoulder":{"label":"The key's channel: how far behind the shoulder its round rear end reaches, under the T's block","kind":"length","measurements":[{"id":"raptor","value":0.171,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{radian-raptor-charging-handle.channel_rear_behind_shoulder}","via":"harvest"},"note":"The Raptor's, read on Primary Arms' photo of that handle from below."}],"note":"The T's aluminium body is the Raptor's: T.REX ARMS' page for the family says of the LT: \"Same as the Standard but features aluminum latches over-molded with high-strength reinforced polymer.\" (https://www.trex-arms.com/store/Radian-Weapons-Raptor-Charging-Handle/), and the Raptor's upper plate, the arc at its front and its block, carried by the two pivot pins, lie on the LT's own in Primary Arms' photo of it from above (5d168cd4d6e1; references/radian-raptor-lt-charging-handle/scratch/xfer_L.png), within 2 px of 416 to the inch. In the LT's photo from below the channel's round end is under the block as the Raptor's is (about column 375, the shoulder at 421.5: 0.17)."},"pin_d":{"label":"The handles' pivot pins: their ends' diameter","kind":"length","measurements":[{"id":"raptor","value":0.06,"unit":"in","pm":0.008,"source":{"type":"derived","expr":"{radian-raptor-charging-handle.pin_d}","via":"harvest"},"note":"The Raptor's, read on Primary Arms' photo of that handle from above."}],"note":"The T's aluminium body is the Raptor's: T.REX ARMS' page for the family says of the LT: \"Same as the Standard but features aluminum latches over-molded with high-strength reinforced polymer.\" (https://www.trex-arms.com/store/Radian-Weapons-Raptor-Charging-Handle/), and the Raptor's upper plate, the arc at its front and its block, carried by the two pivot pins, lie on the LT's own in Primary Arms' photo of it from above (5d168cd4d6e1; references/radian-raptor-lt-charging-handle/scratch/xfer_L.png), within 2 px of 416 to the inch. The LT's pins show as the same bright rings in dark counterbores, 0.859 apart in its plan (the Raptor's: 0.856)."},"rear_rib_count":{"label":"The ribs down each handle's rear face: how many","kind":"count","measurements":[{"id":"photo","value":5,"unit":"count","source":{"type":"photo","photo":"references/radian-raptor-lt-charging-handle 5d168cd4d6e1 (Primary Arms: the black R0148's T from above, on white, 2200 x 1467)","scaleRef":"none: a count","method":"the lobes along each handle's rear edge on gridded enlargements (scratch/g_bayR.png, g_bayL.png): five on the right handle, five on the left","via":"harvest"}}],"note":"Counted on views that show the whole face: five lobes standing out of each handle's rear edge in Primary Arms' photo from above and five in its photo from below, five upright ribs on the left handle's rear face in Wing Tactical's photo from behind (aab96ff5153e) and five on the right handle's (34a97ed88212, with Radian's mark moulded in beyond them). Ribs, not grooves: they stand out of the outline seen from above (a groove would notch it)."},"rear_rib_pitch":{"label":"The ribs down each handle's rear face: their pitch along the face","kind":"length","measurements":[{"id":"photo","value":0.096,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/radian-raptor-lt-charging-handle 5d168cd4d6e1 (Primary Arms: the black R0148's T from above, on white, 2200 x 1467)","scaleRef":"the two pins' ends, 357.2 px apart for the 0.859 in the plan has between them: 415.9 px/in","method":"the five lobes' crests on each handle: eight spacings, 0.090 to 0.102, mean 0.096","via":"harvest"}}]},"rear_rib_r":{"label":"The ribs down each handle's rear face: half their width (each is drawn as a round)","kind":"length","measurements":[{"id":"photo","value":0.012,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/radian-raptor-lt-charging-handle 5d168cd4d6e1 (Primary Arms: the black R0148's T from above, on white, 2200 x 1467)","scaleRef":"the two pins' ends: 415.9 px/in","method":"a lobe is about 10 px across where it leaves the edge's line (scratch/g_bayR.png at 6x)","via":"harvest"}}]},"rear_rib_height":{"label":"The ribs down each handle's rear face: how far their crests stand off the face","kind":"length","measurements":[{"id":"photo","value":0.015,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/radian-raptor-lt-charging-handle 5d168cd4d6e1 (Primary Arms: the black R0148's T from above, on white, 2200 x 1467)","scaleRef":"the two pins' ends: 415.9 px/in","method":"the edge between two lobes lies 6 to 7 px inside the line through their crests (three places on the right handle)","via":"harvest"}}]},"front_groove_count":{"label":"The grooves down the right-hand handle's front face: how many","kind":"count","measurements":[{"id":"photo","value":7,"unit":"count","source":{"type":"photo","photo":"references/radian-raptor-lt-charging-handle 5d168cd4d6e1 (Primary Arms: the black R0148's T from above, on white, 2200 x 1467)","scaleRef":"none: a count","method":"the dips of the right handle's front edge between its tip and its root: seven","via":"harvest"}}],"note":"Counted on the front edge's own profile in the photo from above (references/radian-raptor-lt-charging-handle/scratch/teeth.py, teeth2.py: a line walked beside the edge, how far the edge lies inside it every pixel; a groove is where it dips in): seven dips on the right handle, 39 px apart. The plan, traced from below, has seven teeth there too. Through the fitted camera the near handle's face in Primary Arms' oblique photo (a2724ae397a9) shows those seven and a finer line between each two (scratch/count.py: ten dark lines, 0.045 apart where both kinds are plain): the finer ones don't notch the edge seen from above, and aren't drawn."},"front_groove_count_left":{"label":"The grooves down the left-hand handle's front face: how many","kind":"count","measurements":[{"id":"photo","value":6,"unit":"count","source":{"type":"photo","photo":"references/radian-raptor-lt-charging-handle 5d168cd4d6e1 (Primary Arms: the black R0148's T from above, on white, 2200 x 1467)","scaleRef":"none: a count","method":"the dips of the left handle's front edge between its root and its tip: six","via":"harvest"}}],"note":"The left handle is the shorter by an eighth of an inch, and has one groove fewer: six dips in the same profile (the outermost a shallow one), then the tip's round. The plan has six teeth there."},"front_groove_pitch":{"label":"The grooves down each handle's front face: their pitch along the face","kind":"length","measurements":[{"id":"photo","value":0.095,"unit":"in","pm":0.002,"source":{"type":"photo","photo":"references/radian-raptor-lt-charging-handle 5d168cd4d6e1 (Primary Arms: the black R0148's T from above, on white, 2200 x 1467)","scaleRef":"the two pins' ends, 357.2 px apart for the 0.859 in the plan has between them: 415.9 px/in","method":"the dips' centres on each handle's front edge: 39.2 px apart on the right handle (38.5 to 39.8), 39.8 on the left","via":"harvest"}}]},"front_groove_width":{"label":"The grooves down each handle's front face: their width at half their depth","kind":"length","measurements":[{"id":"photo","value":0.043,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/radian-raptor-lt-charging-handle 5d168cd4d6e1 (Primary Arms: the black R0148's T from above, on white, 2200 x 1467)","scaleRef":"the two pins' ends, 357.2 px apart for the 0.859 in the plan has between them: 415.9 px/in","method":"a dip in the edge's profile is 16 to 20 px wide at half its depth (the right handle's four middle grooves, read every 4 px), a rib between two 19 to 23","via":"harvest"}}]},"front_groove_depth":{"label":"The grooves down each handle's front face: their depth below the ribs' crests","kind":"length","measurements":[{"id":"photo","value":0.024,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/radian-raptor-lt-charging-handle 5d168cd4d6e1 (Primary Arms: the black R0148's T from above, on white, 2200 x 1467)","scaleRef":"the two pins' ends, 357.2 px apart for the 0.859 in the plan has between them: 415.9 px/in","method":"a dip's floor lies 9 to 11 px inside the crests either side of it (the right handle's five middle grooves; the left's 10 to 12, its outermost 8)","via":"harvest"},"note":"Seen from above: the depth at the upper face's edge, which is broken; down the face the grooves may be deeper."}]}}},{"subject":"radian-raptor-sd-charging-handle","title":"Radian Weapons Raptor-SD Ambidextrous Charging Handle AR15/M16, black (R0006)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"wing","value":1.38,"unit":"oz","pm":0.005,"stated":"Weight: 1.38 oz.","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Radian AR-15 Silencer-Optimized Raptor-SD Ambidextrous Charging Handle, SPECIFICATIONS (MPN: R0006 / R0065 / R0066 / R0067 / R0068 / R0255 / R0561)","url":"https://www.wingtactical.com/firearm-parts-accessories/radian-ar-15-silencer-optimized-raptor-sd-ambidextrous-charging-handle/","retrieved":"2026-10-19","via":"harvest"},"note":"One figure for every colour the page sells."},{"id":"alexanders","value":1.38,"unit":"oz","pm":0.005,"stated":"Weight: Approx. 1.38 oz","source":{"type":"spec","publisher":"retailer","name":"Alexander's, Radian Raptor-SD Charging Handle Black - AR-15 5.56 (R0006, UPC 817093020491)","url":"https://alexandersstore.com/product/radian-raptor-sd-chrgng-hndl-556-blk/","retrieved":"2026-10-19","via":"harvest"}},{"id":"alexanders_grey","value":1.3,"unit":"oz","pm":0.05,"stated":"Weight: Approx. 1.3 oz","source":{"type":"spec","publisher":"retailer","name":"Alexander's, Radian Raptor-SD AR-15 Charging Handle - Radian Grey (R0561, UPC 817093025441)","url":"https://alexandersstore.com/product/radian-raptor-sd-chrgng-hndl-556-gry/","retrieved":"2026-10-19","via":"harvest"},"note":"Its prose says \"coming in right around 1.3 ounces, the same as the original Raptor\"."},{"id":"spicetac","value":1.3,"unit":"oz","pm":0.05,"stated":"\"How much does the Raptor SD charging handle weigh?\" The answer is 1.3 ounces.","source":{"type":"spec","publisher":"review","name":"SpiceTac, The Ultimate Raptor Charging Handle Review - All Models: the reviewer's own weighing of each model","url":"https://www.spicetac.com/blog/the-ultimate-raptor-charging-handle-review-all-models/","retrieved":"2026-10-19","via":"harvest"},"note":"A kitchen scale's tenth of an ounce (the same review weighs the plain Raptor at 1.3 too)."}],"adopt":{"from":"wing","reason":"Two sellers state 1.38 for the black one in the same words; the reviewer's scale and the grey one's page read a tenth of an ounce, which 1.38 is just outside (1.25 to 1.35): the disagreement stays here. The model's metal comes to about this (the test)."},"note":"Radian's page states none. Two sellers give 1.38 oz for the black one; one seller's grey one and a reviewer's own weighing give 1.3: kept as a conflict, a tenth of an ounce apart."},"length":{"label":"The shaft: its shoulder (the front face of the ledge under the T's block) to the front hook's tip","kind":"length","measurements":[{"id":"standard","value":5.895,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{aero-charging-handle.length}","via":"harvest"},"note":"US Army TDP drawing 8448518 (Handle, Charging), rev G, side view: 5.600 and .295."}],"note":"The standard's, by expression: no page states a length (every length on a seller's page is a box's: 10.45, 10.95 and 11.5 in at Alexander's). \"FOR AR15/M16\" is etched on the shaft (Primary Arms R0006_04; Impact Guns' render from above). Primary Arms' photo from below reads it at the shaft's own scale (the plan's check)."},"shaft_width":{"label":"The shaft's width","kind":"length","measurements":[{"id":"standard","value":0.4,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{aero-charging-handle.shaft_width}","via":"harvest"},"note":"US Army TDP drawing 8448518, plan view: .400 -B-."}],"note":"The standard's, by expression: the channel it runs in is the standard's. It is the plan photo's scale. \"The square shaft profile fills gaps in the receiver, forcing excess gas back through the ports\" (T.REX ARMS): the shaft is the standard's square section, not a narrowed one."},"shaft_thickness":{"label":"The shaft's thickness","kind":"length","measurements":[{"id":"standard","value":0.2985,"unit":"in","pm":0.0035,"source":{"type":"derived","expr":"{aero-charging-handle.shaft_thickness}","via":"harvest"},"note":"US Army TDP drawing 8448518, side view: .2985 ±.0035."}]},"channel_width":{"label":"The key's channel under the shaft: its width","kind":"length","measurements":[{"id":"standard","value":0.312,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-mk2-charging-handle.channel_width}","via":"harvest"},"note":"US Army TDP drawing 8448518 (Handle, Charging), rev G, Section A-A: .312, with FULL R."}]},"channel_depth":{"label":"The key's channel: its depth from the shaft's underside to the top of its round roof","kind":"length","measurements":[{"id":"standard","value":0.25,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-mk2-charging-handle.channel_depth}","via":"harvest"},"note":"US Army TDP drawing 8448518, Section A-A: .250."}]},"hook_length":{"label":"The front hook: its rear face to its tip","kind":"length","measurements":[{"id":"standard","value":0.295,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-mk2-charging-handle.hook_length}","via":"harvest"},"note":"US Army TDP drawing 8448518, side view: .295."}]},"hook_drop":{"label":"The front hook: how far it hangs below the shaft's underside","kind":"length","measurements":[{"id":"standard","value":0.275,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-mk2-charging-handle.hook_drop}","via":"harvest"},"note":"US Army TDP drawing 8448518, side view: .275 -C-."}]},"hook_fillet_r":{"label":"The front hook: the round between its rear face and the shaft's underside","kind":"length","measurements":[{"id":"standard","value":0.187,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-mk2-charging-handle.hook_fillet_r}","via":"harvest"},"note":"US Army TDP drawing 8448518, side view: .187 R."}]},"guide_lug_width":{"label":"Across the two guide lugs near the shaft's front end","kind":"length","measurements":[{"id":"standard","value":0.488,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-mk2-charging-handle.guide_lug_width}","via":"harvest"},"note":"US Army TDP drawing 8448518, end view: .488."}]},"guide_lug_height":{"label":"The guide lugs' height, from the shaft's underside up","kind":"length","measurements":[{"id":"standard","value":0.119,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{bcm-mk2-charging-handle.guide_lug_height}","via":"harvest"},"note":"US Army TDP drawing 8448518, end view: .119 ±.002."}]},"latch_reach":{"label":"The right-hand latch's reach: its tip off the shaft's right side face, across","kind":"length","measurements":[{"id":"photo","value":1.163,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/radian-raptor-sd-charging-handle b55302018bd7 (Primary Arms R0006_01: the black R0006 from below, on white, 2200 x 1467)","scaleRef":"the shaft's width column by column (shaft_width)","method":"the traced plan's furthest point to the handle's right, 1.363 off the shaft's centre line, less half the shaft's width","via":"harvest"}}],"note":"No page states one. Primary Arms classes the SD's latches as \"Large Latch\" and Wing Tactical says \"Extended latch for positive engagement\"."},"latch_reach_left":{"label":"The left-hand latch's reach: its tip off the shaft's left side face, across","kind":"length","measurements":[{"id":"photo","value":1.035,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/radian-raptor-sd-charging-handle b55302018bd7 (Primary Arms R0006_01: the black R0006 from below, on white, 2200 x 1467)","scaleRef":"the shaft's width column by column (shaft_width)","method":"the traced plan's furthest point to the handle's left, 1.235 off the shaft's centre line, less half the shaft's width","via":"harvest"}}]},"t_width":{"label":"The T, side to side: across the two latches' tips","kind":"length","measurements":[{"id":"photo","value":2.599,"unit":"in","pm":0.038,"source":{"type":"photo","photo":"references/radian-raptor-sd-charging-handle b55302018bd7 (Primary Arms: the black R0006 from below, on white, 2200 x 1467 (R0006_01))","scaleRef":"scale from radian-raptor-sd-charging-handle.shaft_width = 0.4 in, the tube's own width column by column: 110.8 px over columns 560–900, 110.8 px over columns 950–1230, 111.1 px over columns 1960–2030; a line through them (rms 0.20 px) changes +0.7% from column 560 to 2030, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 277.3 px/in there. The axis is the tube's centre line (tilt -0.06°, rms 0.16 px)","method":"height of the traced outline (tools/trace.py); across the two latches' tips (their lower faces' edges)","via":"harvest"}}]},"t_depth":{"label":"The T, front to back: its rear face behind the shoulder","kind":"length","measurements":[{"id":"photo","value":1.083,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/radian-raptor-sd-charging-handle b55302018bd7 (Primary Arms: the black R0006 from below, on white, 2200 x 1467 (R0006_01))","scaleRef":"scale from radian-raptor-sd-charging-handle.shaft_width = 0.4 in, the tube's own width column by column: 110.8 px over columns 560–900, 110.8 px over columns 950–1230, 111.1 px over columns 1960–2030; a line through them (rms 0.20 px) changes +0.7% from column 560 to 2030, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 277.3 px/in there. The axis is the tube's centre line (tilt -0.06°, rms 0.16 px)","method":"−x_min of the traced outline (tools/trace.py); the T's rear face behind the shoulder","via":"harvest"}}]},"t_height":{"label":"The T's height: its top (the latches' upper faces and the plate between them, level in the side view) above the shaft's underside","kind":"length","measurements":[{"id":"side","value":0.403,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/radian-raptor-sd-charging-handle 96319b30010d (Impact Guns radian-r0006-2: the maker's render of the black R0006 from its right side, 1500 x 163)","scaleRef":"the shaft's own thickness across the plain stretch of the shaft (columns 300 to 880): its top edge at row 33.17 and its underside at 94.68 (where each column crosses 128 of 255), 61.5 px for shaft_thickness .2985, with the hook's drop: rows 94.68 to 153.27, 58.6 px for hook_drop .275; the two together, 120.1 px for .5735: 209.4 px/in up and down (the thickness alone reads 206.1, the drop alone 213.1: ± 2%)","method":"the T's top edge over columns 20 to 190 (the latch's tip to its root) at row 10.30 (7.7 to 13.8: its upper edge is broken), the shaft's underside at 94.68: 84.4 px","via":"harvest"}}]},"latch_lift":{"label":"A latch's lower face above the shaft's underside","kind":"length","measurements":[{"id":"side","value":0,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/radian-raptor-sd-charging-handle 96319b30010d (Impact Guns radian-r0006-2: the maker's render of the black R0006 from its right side, 1500 x 163)","scaleRef":"the shaft's own thickness across the plain stretch of the shaft (columns 300 to 880): its top edge at row 33.17 and its underside at 94.68 (where each column crosses 128 of 255), 61.5 px for shaft_thickness .2985, with the hook's drop: rows 94.68 to 153.27, 58.6 px for hook_drop .275; the two together, 120.1 px for .5735: 209.4 px/in up and down (the thickness alone reads 206.1, the drop alone 213.1: ± 2%)","method":"the T's lowest dark row (96 over columns 10 to 200) against the shaft's underside (94.68 by the 128 crossing, its lowest dark row 95 to 96): within a pixel","via":"harvest"}}],"note":"In the side view the T's lower edge runs on level with the shaft's underside (row 96 at the T, 94.7 to 95.5 along the shaft): the latches' lower faces are drawn flush with it."},"block_front_behind_shoulder":{"label":"The T's tall part's front end (the latch's root beside the block), behind the shoulder","kind":"length","measurements":[{"id":"side","value":0.107,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/radian-raptor-sd-charging-handle 96319b30010d (Impact Guns radian-r0006-2: the maker's render of the black R0006 from its right side, 1500 x 163)","scaleRef":"the hook's tip (column 1489) at length ahead of the shoulder at 213 px/in along (the pitch's scale, 96.0 px for port_pitch): the shoulder at column 228","method":"the T's top drops from the latch's height to the shaft's at column 205 (± 3)","via":"harvest"}}]},"catch_bottom":{"label":"The latch's hook arm (what catches the receiver, on the left): its underside above the shaft's underside","kind":"length","measurements":[{"id":"patent","value":0.086,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/radian-raptor-sd-charging-handle c52df6858fe2 (US D694,354 S, 'Firearm charging handle', sheet 4 of 5: FIG. 5 and FIG. 6, the two side views; the patent office's PDF, 2560 x 3300)","scaleRef":"the shaft's own thickness in the same figure (shaft_thickness): its broken lines 134.5 px apart in FIG. 5 (450.6 px/in) and 128 px in FIG. 6 (428.8 px/in)","method":"the hook's broken box ahead of the latch: its nearer line 39 px from the shaft's underside line in FIG. 5 (0.087), 36 px in FIG. 6 (0.084): the pixel counts the Raptor's ledger took off the same sheet, read again here as this handle's own patent","via":"harvest"},"note":"Broken lines: the patent's environment, not its claim."}],"note":"From the design patent's broken lines alone: no view of the SD shows its left side square on. US D694,354 is on Radian's patents page for the RAPTOR-SD and etched on the SD's shaft (Impact Guns' render from above, Primary Arms R0066_00)."},"catch_top":{"label":"The latch's hook arm: its top above the shaft's underside","kind":"length","measurements":[{"id":"patent","value":0.217,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/radian-raptor-sd-charging-handle c52df6858fe2 (US D694,354 S, 'Firearm charging handle', sheet 4 of 5: FIG. 5 and FIG. 6)","scaleRef":"the shaft's own thickness in the same figure (shaft_thickness): 450.6 px/in in FIG. 5, 428.8 in FIG. 6","method":"the hook's broken box ahead of the latch: its further line 97 px from the shaft's underside line in FIG. 5 (0.215), 94 px in FIG. 6 (0.219)","via":"harvest"},"note":"Broken lines: the patent's environment, not its claim."}]},"lower_plate_thickness":{"label":"The ledge under the T's block (the lower plate run on to the shoulder): its top above the shaft's underside","kind":"length","measurements":[{"id":"patent","value":0.086,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/radian-raptor-sd-charging-handle c52df6858fe2 (US D694,354 S, 'Firearm charging handle', sheet 4 of 5: FIG. 5 and FIG. 6)","scaleRef":"the shaft's own thickness in the same figure (shaft_thickness): 450.6 px/in in FIG. 5, 428.8 in FIG. 6","method":"the lower of the two broken lines along the T's body between the latch and the shoulder, on both sides: 39 px above the shaft's underside line in FIG. 5 (0.087), 36 px in FIG. 6 (0.084)","via":"harvest"},"note":"Broken lines: the patent's environment, not its claim."}]},"channel_rear_behind_shoulder":{"label":"The key's channel: how far behind the shoulder its round rear end reaches, under the T's block","kind":"length","measurements":[{"id":"photo","value":0.106,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/radian-raptor-sd-charging-handle b55302018bd7 (Primary Arms R0006_01: the black R0006 from below, on white, 2200 x 1467)","scaleRef":"the shaft's width column by column (shaft_width): 277.3 px/in there","method":"the channel's round end at column 392 (± 5) on the shaft's centre line, the shoulder being at column 421.5","via":"harvest"}}]},"pin_d":{"label":"The latches' pivot pins: their ends' diameter","kind":"length","measurements":[{"id":"photo","value":0.065,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/radian-raptor-sd-charging-handle b55302018bd7 (Primary Arms R0006_01: the black R0006 from below, on white, 2200 x 1467)","scaleRef":"the shaft's width column by column (shaft_width): 277.3 px/in","method":"each pin's bright end (over 150 of 255): 16 to 22 px across (columns 244 to 266 and 249 to 264)","via":"harvest"}}]},"port_count":{"label":"The ports along each top corner of the shaft: how many","kind":"count","measurements":[{"id":"photo","value":6,"unit":"count","source":{"type":"photo","photo":"references/radian-raptor-sd-charging-handle b55302018bd7 (Primary Arms R0006_01: the black R0006 from below, on white, 2200 x 1467)","scaleRef":"none: a count","method":"the white holes seen through the channel: six on each side of its centre line, in pairs at one place along the shaft (the trace's `ports` feature: twelve)","via":"harvest"}}],"note":"Counted on three views that show the whole run: six holes on each side seen through the channel from below (Primary Arms R0006_01: twelve), six notch-and-hole pairs along both edges from above (Impact Guns' render), six notches along the near corner from the side (Impact Guns' render)."},"port_pitch":{"label":"The ports' pitch along the shaft","kind":"length","measurements":[{"id":"photo","value":0.4425,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/radian-raptor-sd-charging-handle b55302018bd7 (Primary Arms R0006_01: the black R0006 from below, on white, 2200 x 1467)","scaleRef":"the shaft's width column by column (shaft_width), and put to the drawing's length as the plan is (the hook's tip reads 5.968 for 5.895: lengths by 0.98777)","method":"the twelve holes' centres in the plan (the trace's `ports` feature), pair by pair 3.093, 3.542, 3.991, 4.440, 4.887, 5.333 ahead of the shoulder: 0.448 a pitch (0.447 to 0.449), by 0.98777","via":"harvest"}}]},"port_notch_depth":{"label":"A port's notch: how far it is cut down the shaft's side face from the top (and, its face being on the corner's diagonal, as far in across the top)","kind":"length","measurements":[{"id":"side","value":0.116,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/radian-raptor-sd-charging-handle 96319b30010d (Impact Guns radian-r0006-2: the maker's render of the black R0006 from its right side, 1500 x 163)","scaleRef":"the shaft's own thickness across the plain stretch of the shaft (columns 300 to 880): its top edge at row 33.17 and its underside at 94.68 (where each column crosses 128 of 255), 61.5 px for shaft_thickness .2985, with the hook's drop: rows 94.68 to 153.27, 58.6 px for hook_drop .275; the two together, 120.1 px for .5735: 209.4 px/in up and down (the thickness alone reads 206.1, the drop alone 213.1: ± 2%)","method":"the notch's sloped face, lit, from the shaft's top edge (row 33.2) to its lower edge on the side face (row 57.5, where the five faces' lit band ends): 24.3 px","via":"harvest"}},{"id":"top","value":0.116,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/radian-raptor-sd-charging-handle 39774426de42 (Impact Guns radian-r0006: the maker's render of the black R0006 from above, 2500 x 930)","scaleRef":"the shaft's own width there, 142.5 px for shaft_width .400: 356 px/in","method":"the notch (its dark sloped face) from the shaft's edge in to its inner edge on the top: 41 px, on the fourth pair (columns 1600 to 1900)","via":"harvest"}}],"adopt":{"from":"side","reason":"The two views agree; the side view's edge is the sharper."}},"port_hole_d":{"label":"A port's hole: its diameter (square to the notch's face)","kind":"length","measurements":[{"id":"top","value":0.115,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/radian-raptor-sd-charging-handle 39774426de42 (Impact Guns radian-r0006: the maker's render of the black R0006 from above, 2500 x 930)","scaleRef":"the shaft's own width there, 142.5 px for shaft_width .400: 356 px/in","method":"the hole's rim along the shaft (across it the 45-degree face foreshortens it): 41 px","via":"harvest"}},{"id":"side","value":0.115,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/radian-raptor-sd-charging-handle 96319b30010d (Impact Guns radian-r0006-2: the maker's render of the black R0006 from its right side, 1500 x 163)","scaleRef":"the ports' own pitch along the shaft (port_pitch, read on the plan): 96.0 px between each two holes' centres in this render (991, 1086, 1183, 1279, 1375): 0.00461 in a pixel along; the render's along and across scales differ by about 3% (its aspect isn't square), so lengths along are taken at the pitch's scale, not the thickness's","method":"the hole's rim along the shaft (its dark crescent and the white seen through it): 25 px","via":"harvest"}}],"adopt":{"from":"top","reason":"The two views agree."}},"port_floor_rear":{"label":"A port's notch at its lower edge (on the side face): its rear wall, behind the hole's centre","kind":"length","measurements":[{"id":"side","value":0.138,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/radian-raptor-sd-charging-handle 96319b30010d (Impact Guns radian-r0006-2: the maker's render of the black R0006 from its right side, 1500 x 163)","scaleRef":"the ports' own pitch along the shaft (port_pitch, read on the plan): 96.0 px between each two holes' centres in this render (991, 1086, 1183, 1279, 1375): 0.00461 in a pixel along; the render's along and across scales differ by about 3% (its aspect isn't square), so lengths along are taken at the pitch's scale, not the thickness's","method":"the lit face's lower edge (row 56) begins 32, 31, 32, 28 and 27 px behind the five whole ports' hole centres: mean 30.0 px","via":"harvest"}}],"note":"The notch's two end walls lean forward going up (US 10,203,174 FIG. 9B; the side render): its outline on the side face is a parallelogram, these four figures its corners."},"port_floor_front":{"label":"A port's notch at its lower edge: its front wall, ahead of the hole's centre","kind":"length","measurements":[{"id":"side","value":0.092,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/radian-raptor-sd-charging-handle 96319b30010d (Impact Guns radian-r0006-2: the maker's render of the black R0006 from its right side, 1500 x 163)","scaleRef":"the ports' own pitch along the shaft (port_pitch, read on the plan): 96.0 px between each two holes' centres in this render (991, 1086, 1183, 1279, 1375): 0.00461 in a pixel along; the render's along and across scales differ by about 3% (its aspect isn't square), so lengths along are taken at the pitch's scale, not the thickness's","method":"the lit face's lower edge (row 56) ends 18, 19, 18, 22 and 22 px ahead of the hole centres: mean 19.8 px","via":"harvest"}}]},"port_top_rear":{"label":"A port's notch at the shaft's top: its rear wall, behind the hole's centre","kind":"length","measurements":[{"id":"side","value":0.059,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/radian-raptor-sd-charging-handle 96319b30010d (Impact Guns radian-r0006-2: the maker's render of the black R0006 from its right side, 1500 x 163)","scaleRef":"the ports' own pitch along the shaft (port_pitch, read on the plan): 96.0 px between each two holes' centres in this render (991, 1086, 1183, 1279, 1375): 0.00461 in a pixel along; the render's along and across scales differ by about 3% (its aspect isn't square), so lengths along are taken at the pitch's scale, not the thickness's","method":"the lit face at row 34 (a pixel under the top edge) begins 13, 12, 13, 13 px behind the hole centres: mean 12.8 px","via":"harvest"}}]},"port_top_front":{"label":"A port's notch at the shaft's top: its front wall, ahead of the hole's centre","kind":"length","measurements":[{"id":"side","value":0.19,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/radian-raptor-sd-charging-handle 96319b30010d (Impact Guns radian-r0006-2: the maker's render of the black R0006 from its right side, 1500 x 163)","scaleRef":"the ports' own pitch along the shaft (port_pitch, read on the plan): 96.0 px between each two holes' centres in this render (991, 1086, 1183, 1279, 1375): 0.00461 in a pixel along; the render's along and across scales differ by about 3% (its aspect isn't square), so lengths along are taken at the pitch's scale, not the thickness's","method":"the lit face at row 34 ends 41, 42, 41, 41 px ahead of the hole centres: mean 41.3 px","via":"harvest"}}]},"plate_arc_behind_pins":{"label":"The upper plate's arc (concave toward the muzzle, round the logo): its middle, behind the line through the two pins","kind":"length","measurements":[{"id":"top","value":0.12,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/radian-raptor-sd-charging-handle 39774426de42 (Impact Guns radian-r0006: the maker's render of the black R0006 from above, 2500 x 930)","scaleRef":"the shaft's own width there, 142.5 px for shaft_width .400: 356 px/in","method":"the arc's rearmost point on the centre line at column 141 (± 4), the two pins' centres at column 185: 44 px","via":"harvest"}},{"id":"fde","value":0.099,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/radian-raptor-sd-charging-handle 5b965fca6fda (Primary Arms R0066_01: the FDE one's T from above, the muzzle down, 2200 x 1467)","scaleRef":"the two pins' centres (830, 445 and 1457, 445, ± 3 px) 627 px apart for the 0.869 the plan has between them (the trace's `pins`): 721.5 px/in, on the plate's own top","method":"the arc's rearmost point on the centre line at row 374 (± 5), the pins' centres at row 445.5: 71.5 px","via":"harvest"}}],"adopt":{"from":"fde","reason":"The larger picture of the two, on the plate's own top; the render from above reads 0.12, within the two readings' ±."}},"plate_ear_r":{"label":"The upper plate's ears round the two pins: their outer radius","kind":"length","measurements":[{"id":"top","value":0.105,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/radian-raptor-sd-charging-handle 39774426de42 (Impact Guns radian-r0006: the maker's render of the black R0006 from above, 2500 x 930)","scaleRef":"the shaft's own width there, 142.5 px for shaft_width .400: 356 px/in","method":"each ear's rounded edge about its pin, ahead of and beside it: 37 px (± 5) from the pin's centre","via":"harvest"}}]},"plate_arc_r":{"label":"The upper plate's arc round the logo: its radius (a circle centred ahead of it on the centre line)","kind":"length","measurements":[{"id":"fde","value":0.346,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/radian-raptor-sd-charging-handle 5b965fca6fda (Primary Arms R0066_01: the FDE one's T from above, the muzzle down, 2200 x 1467)","scaleRef":"the two pins' centres (830, 445 and 1457, 445, ± 3 px) 627 px apart for the 0.869 the plan has between them (the trace's `pins`): 721.5 px/in, on the plate's own top","method":"the arc's ends, where it meets the ears (918, 517 and 1370, 517, ± 10 px): a chord of 452 px (0.627) with a sagitta of 143 px (0.198) to its rearmost point: a circle of 0.346","via":"harvest"}}]}}},{"subject":"radian-talon-safety-selector","title":"Radian Weapons Talon 45/90 - 2 Lever Kit","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"wing","value":0.53,"unit":"oz","pm":0.05,"stated":"Weight: ~0.53 oz.","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Radian Talon Ambi 45/90 Safety Selector (2 Lever Set)","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/lower-receiver-parts/lower-receiver-parts/radian-talon-ambi-45-90-safety-selector-2-lever-set/","retrieved":"2026-10-12","via":"harvest"},"note":"The seller's own figure (\"~\"), for the 2-lever set."},{"id":"a15d","value":0.04,"unit":"oz","stated":"Weight 0.04 oz","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, Radian Talon Ambidextrous 45/90 2-Lever Safety Selector","url":"https://ar15discounts.com/products/radian-talon-ambidextrous-45-90-2-lever-safety-selector/","retrieved":"2026-10-12","via":"harvest"},"note":"\"Additional information\" on the seller's page: a twentieth of what the steel shaft alone weighs."},{"id":"pa","value":0.11,"unit":"lb","stated":"Weight 0.11","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Radian Weapons Talon Ambidextrous Safety Selector 2-Lever Kit (R0018)","url":"https://www.primaryarms.com/radian-weapons-talon-ambidextrous-safety-selector-2-lever-kit-r0018","retrieved":"2026-10-12","via":"harvest"},"note":"The seller's table gives no unit. Entered as pounds (1.76 oz), the only unit that makes it more than the shaft's steel: a figure for the kit in its packet, with its tool, studs, springs and detent. As ounces it would be a sixth of the shaft."},{"id":"arbuild","value":1.92,"unit":"oz","stated":"Weight: 1.92 oz","source":{"type":"spec","publisher":"review","name":"AR15.BUILD, Radian Weapons Talon Ambidextrous 45/90 Safety Selector Kit (MPN R0567)","url":"https://ar15.build/products/safety-selector/285391/radian-weapons-talon-ambidextrous-45-radian-weapons-talon-ambidextrous-45-90-safety-selector-kit-for","retrieved":"2026-10-12","via":"harvest"},"note":"A parts database's listing of the Radian Grey kit (MPN R0567): the kit as packed, or a default. MidwayUSA gives only \"Shipping Weight 0.133 Pounds - 0.183 Pounds\" (2.1 to 2.9 oz, a carton), a range and not a figure."},{"id":"metal","value":0.775,"unit":"oz","pm":0.2,"source":{"type":"derived","expr":"(0.785398163 * {.shaft_d} * {.shaft_d} * {.shaft_length} + ({.dovetail_width_top} + {.dovetail_width_base}) * {.dovetail_height} * {.shaft_d}) * {std.density.steel} + (2 * 0.785398163 * {.head_d} * {.head_d} * ({.head_t_top} + {.head_t_shelf}) / 2 + {.lever_width} * ({.lever_reach} + {.short_lever_reach} - 2 * {.shelf_start}) * ({.lever_standoff} + {.lever_tip_t}) / 2) * {std.density.aluminium_7075}","via":"harvest"},"note":"WORKED OUT: the pieces drawn, as their metal: the steel shaft as a plain cylinder with its two dovetails, the two levers as 7075 (each a disc of the head's mean thickness and a bar of the thumb piece's). An upper figure: the shaft's cut for the trigger's tail, its detent grooves and its two stud bores, and the levers' scooped heads, dovetail slots and grooves aren't taken off."}],"adopt":{"from":"wing","reason":"The one published figure the part's own metal bears out: the pieces as drawn, uncut, come to about three quarters of an ounce, and what isn't taken off them (half the shaft's middle for the trigger's tail, the detent's grooves, the studs' bores, the levers' scoops and slots) brings that down toward Wing Tactical's ~0.53. The other three are a twentieth of the shaft's steel (0.04 oz), a packet (0.11 with no unit, 1.76 oz as pounds) and a carton or a default (1.92 oz). Kept beside it, all of them."},"note":"Radian states none. Four sellers' figures, forty-eight times apart; and the part's own metal as it is drawn."},"shaft_d":{"label":"Diameter of the shaft that turns in the receiver","kind":"length","measurements":[{"id":"standard","value":0.37225,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{std.ar15.selector_shaft_d}","via":"user"},"note":"NOT RADIAN'S FIGURE: no page states one. The shaft turns in the standard's hole (.376 ±.001, std.ar15.selector_hole_d), so it is taken as the Army's own selector's diameter (drawing 9381367: .3730 -.0015, std.ar15.selector_shaft_d), with a ± as wide as the room there is under the hole. Every other size here is scaled by it."}]},"shaft_length":{"label":"Length of shaft between the faces that bear on the receiver's two sides","kind":"length","measurements":[{"id":"flat","value":0.9613,"unit":"in","pm":0.009,"source":{"type":"photo","photo":"references/radian-talon-safety-selector 21ba32f12fa4 (Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up)","scaleRef":"the shaft in the same photo, on the same table: 207.1 px between its two edges (columns 1340 to 1460, where the white gives way to the shaft's lit edge) taken as .37225, the diameter of the Army's own selector (.shaft_d), which turns in the same .376 hole (std.ar15.selector_hole_d): 556.3 px/in. NOT scaled by the receiver's width: the shaft's shoulders are 534.8 px apart, and as .88 (std.ar15.lower_body_width) they would make its diameter .341, which doesn't turn in that hole","method":"the shaft's two shoulders, where its full diameter ends and each dovetail begins: x 1314.7 and 1849.5 on rows clear of the dovetails (y 296 and 480), 534.8 px","via":"harvest"},"note":"± for two edges a pixel soft and the scale's 0.7%."},{"id":"edge","value":0.9543,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/radian-talon-safety-selector f09f2e97cdaa (AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement)","scaleRef":"the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5","method":"the long lever's inner face (x 354.5) to the far dovetail's end (x 1288.5), 934.0 px = 1.0232, less one dovetail's height (.dovetail_height)","via":"harvest"},"note":"The lever's inner face lies in the shaft's shoulder plane: the near cylinder shows .824 of a diameter long there, the far one .833."}],"adopt":{"from":"flat","reason":"Both shoulders seen bare, from straight above; the edge-on photo, read from a lever's inner face, agrees within 0.7%."},"note":"For this selector: between its two shoulders, which are the planes its two levers' inner faces lie in. .08 more than the receiver's .88: the levers stand about .04 off each side."},"dovetail_height":{"label":"Height of each dovetail on the shaft's ends, from the shoulder","kind":"length","measurements":[{"id":"flat","value":0.0689,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/radian-talon-safety-selector 21ba32f12fa4 (Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up)","scaleRef":"the shaft in the same photo, on the same table: 207.1 px between its two edges (columns 1340 to 1460, where the white gives way to the shaft's lit edge) taken as .37225, the diameter of the Army's own selector (.shaft_d), which turns in the same .376 hole (std.ar15.selector_hole_d): 556.3 px/in. NOT scaled by the receiver's width: the shaft's shoulders are 534.8 px apart, and as .88 (std.ar15.lower_body_width) they would make its diameter .341, which doesn't turn in that hole","method":"the shaft's ends (x 1277.1 and 1888.6) less its shoulders (1314.7 and 1849.5): 37.6 and 39.1 px, their mean","via":"harvest"}}]},"dovetail_width_top":{"label":"Width of each dovetail at its end (its widest)","kind":"length","measurements":[{"id":"flat","value":0.2786,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/radian-talon-safety-selector 21ba32f12fa4 (Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up)","scaleRef":"the shaft in the same photo, on the same table: 207.1 px between its two edges (columns 1340 to 1460, where the white gives way to the shaft's lit edge) taken as .37225, the diameter of the Army's own selector (.shaft_d), which turns in the same .376 hole (std.ar15.selector_hole_d): 556.3 px/in. NOT scaled by the receiver's width: the shaft's shoulders are 534.8 px apart, and as .88 (std.ar15.lower_body_width) they would make its diameter .341, which doesn't turn in that hole","method":"the left dovetail across the shaft at x 1281, just inside its end: y 304.8 to 459.8, 155.0 px (the right one 148.7 at x 1884)","via":"harvest"}}]},"dovetail_width_base":{"label":"Width of each dovetail at the shoulder (its narrowest)","kind":"length","measurements":[{"id":"flat","value":0.206,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/radian-talon-safety-selector 21ba32f12fa4 (Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up)","scaleRef":"the shaft in the same photo, on the same table: 207.1 px between its two edges (columns 1340 to 1460, where the white gives way to the shaft's lit edge) taken as .37225, the diameter of the Army's own selector (.shaft_d), which turns in the same .376 hole (std.ar15.selector_hole_d): 556.3 px/in. NOT scaled by the receiver's width: the shaft's shoulders are 534.8 px apart, and as .88 (std.ar15.lower_body_width) they would make its diameter .341, which doesn't turn in that hole","method":"the left dovetail across the shaft at x 1308 to 1312, beside the shoulder: 113.4 to 116.1 px (the right one 116.5 to 117.2)","via":"harvest"}}]},"head_d":{"label":"Diameter of each lever's round head","kind":"length","measurements":[{"id":"flat-short","value":0.4801,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/radian-talon-safety-selector 21ba32f12fa4 (Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up)","scaleRef":"the shaft in the same photo, on the same table: 207.1 px between its two edges (columns 1340 to 1460, where the white gives way to the shaft's lit edge) taken as .37225, the diameter of the Army's own selector (.shaft_d), which turns in the same .376 hole (std.ar15.selector_hole_d): 556.3 px/in. NOT scaled by the receiver's width: the shaft's shoulders are 534.8 px apart, and as .88 (std.ar15.lower_body_width) they would make its diameter .341, which doesn't turn in that hole","method":"the short lever's head at its widest row (y 810 to 820): x 1239.5 to 1506.6, 267.1 px; its top at y 681, 133.5 above that row: a circle","via":"harvest"}},{"id":"flat-long","value":0.4805,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/radian-talon-safety-selector 21ba32f12fa4 (Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up)","scaleRef":"the shaft in the same photo, on the same table: 207.1 px between its two edges (columns 1340 to 1460, where the white gives way to the shaft's lit edge) taken as .37225, the diameter of the Army's own selector (.shaft_d), which turns in the same .376 hole (std.ar15.selector_hole_d): 556.3 px/in. NOT scaled by the receiver's width: the shaft's shoulders are 534.8 px apart, and as .88 (std.ar15.lower_body_width) they would make its diameter .341, which doesn't turn in that hole","method":"the long lever's head at its widest row (y 810): x 1621.6 to 1888.9, 267.3 px","via":"harvest"}},{"id":"edge","value":0.4804,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/radian-talon-safety-selector f09f2e97cdaa (AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement)","scaleRef":"the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5","method":"the short lever's head, face-on, at its widest row (y 720): x 1394.1 to 1832.7, 438.5 px","via":"harvest"}}],"adopt":{"from":"flat-short","reason":"Three readings in two photos within a thousandth: the standard selector's hub, .48 DIA."},"note":"The two levers' heads are one size. About the selector's axis: the hole the retention stud snaps into is at the head's middle (within .005), and the long lever's top stands .242 above the shaft's axis in the edge-on photo."},"lever_width":{"label":"Width of each lever's thumb piece","kind":"length","measurements":[{"id":"flat-short","value":0.2522,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/radian-talon-safety-selector 21ba32f12fa4 (Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up)","scaleRef":"the shaft in the same photo, on the same table: 207.1 px between its two edges (columns 1340 to 1460, where the white gives way to the shaft's lit edge) taken as .37225, the diameter of the Army's own selector (.shaft_d), which turns in the same .376 hole (std.ar15.selector_hole_d): 556.3 px/in. NOT scaled by the receiver's width: the shaft's shoulders are 534.8 px apart, and as .88 (std.ar15.lower_body_width) they would make its diameter .341, which doesn't turn in that hole","method":"the short lever's straight sides, rows y 960 to 1050: 140.3 px","via":"harvest"}},{"id":"flat-long","value":0.2569,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/radian-talon-safety-selector 21ba32f12fa4 (Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up)","scaleRef":"the shaft in the same photo, on the same table: 207.1 px between its two edges (columns 1340 to 1460, where the white gives way to the shaft's lit edge) taken as .37225, the diameter of the Army's own selector (.shaft_d), which turns in the same .376 hole (std.ar15.selector_hole_d): 556.3 px/in. NOT scaled by the receiver's width: the shaft's shoulders are 534.8 px apart, and as .88 (std.ar15.lower_body_width) they would make its diameter .341, which doesn't turn in that hole","method":"the long lever's straight sides, rows y 960 to 1160: 142.9 px","via":"harvest"}},{"id":"edge","value":0.264,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/radian-talon-safety-selector f09f2e97cdaa (AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement)","scaleRef":"the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5","method":"the short lever, face-on, rows y 1060 to 1100: 239 to 243 px, its left edge in its own shadow","via":"harvest"}}],"adopt":{"from":"flat-long","reason":"The longer straight run, in the photo from straight above; the short lever's reads .005 less there, and the other photo's reading has a shadowed edge."}},"lever_reach":{"label":"The lever's reach from the selector's axis to its tip","kind":"length","measurements":[{"id":"flat","value":0.797,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/radian-talon-safety-selector 21ba32f12fa4 (Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up)","scaleRef":"the shaft in the same photo, on the same table: 207.1 px between its two edges (columns 1340 to 1460, where the white gives way to the shaft's lit edge) taken as .37225, the diameter of the Army's own selector (.shaft_d), which turns in the same .376 hole (std.ar15.selector_hole_d): 556.3 px/in. NOT scaled by the receiver's width: the shaft's shoulders are 534.8 px apart, and as .88 (std.ar15.lower_body_width) they would make its diameter .341, which doesn't turn in that hole","method":"the LONG lever: its tip (y 1251.8) from its head's middle (y 808.5: its top at 674.2 and its widest row), 443.3 px","via":"harvest"}},{"id":"edge","value":0.7817,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/radian-talon-safety-selector f09f2e97cdaa (AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement)","scaleRef":"the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5","method":"the long lever edge-on: its tip at its inner face (y 1428) from the shaft's axis (y 714.5), 713.5 px","via":"harvest"},"note":"The tip's end is raked: at the lever's outer face it is .04 nearer the axis (y 1392)."}],"adopt":{"from":"flat","reason":"Face-on, the tip unmistakable; the edge-on photo reads 1.9% less, inside the two ±."},"note":"The LONG lever, the one drawn on the left side. The short one is short_lever_reach."},"short_lever_reach":{"label":"The short lever's reach from the selector's axis to its tip","kind":"length","measurements":[{"id":"flat","value":0.609,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/radian-talon-safety-selector 21ba32f12fa4 (Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up)","scaleRef":"the shaft in the same photo, on the same table: 207.1 px between its two edges (columns 1340 to 1460, where the white gives way to the shaft's lit edge) taken as .37225, the diameter of the Army's own selector (.shaft_d), which turns in the same .376 hole (std.ar15.selector_hole_d): 556.3 px/in. NOT scaled by the receiver's width: the shaft's shoulders are 534.8 px apart, and as .88 (std.ar15.lower_body_width) they would make its diameter .341, which doesn't turn in that hole","method":"the SHORT lever: its tip (y 1153.3) from its head's middle (y 814.5), 338.8 px","via":"harvest"}},{"id":"edge","value":0.5979,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/radian-talon-safety-selector f09f2e97cdaa (AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement)","scaleRef":"the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5","method":"the short lever face-on: its tip (y 1270, above its shadow) from its head's middle (y 724.2), 545.8 px","via":"harvest"}}],"adopt":{"from":"flat","reason":"The photo from straight above, without a shadow at the tip; the other reads 1.8% less."}},"lever_standoff":{"label":"How far the lever stands out from the receiver's side","kind":"length","measurements":[{"id":"edge","value":0.297,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/radian-talon-safety-selector f09f2e97cdaa (AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement)","scaleRef":"the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5","method":"the long lever edge-on, at its thickest, the thumb piece's top (rows y 820 to 920): its outer edge at x 83.4 to 84.3, 271.1 px out from its inner face","via":"harvest"}}],"note":"From the lever's OWN inner face to the highest of its thumb piece. The inner face itself stands about .04 off a standard receiver's side (shaft_length)."},"head_t_top":{"label":"Thickness of the lever's head at its top edge","kind":"length","measurements":[{"id":"edge","value":0.1303,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/radian-talon-safety-selector f09f2e97cdaa (AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement)","scaleRef":"the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5","method":"the long lever edge-on at y 500, just under the head's top: its outer edge at x 235.6, 118.9 px out from the inner face","via":"harvest"},"note":"The head's outer face rises from here toward the thumb piece in a straight line: .151 at y 560, .179 at 640, .199 at 700."}]},"head_t_shelf":{"label":"Thickness of the lever's head where the thumb piece's step begins","kind":"length","measurements":[{"id":"edge","value":0.2206,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/radian-talon-safety-selector f09f2e97cdaa (AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement)","scaleRef":"the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5","method":"the long lever edge-on at y 760, .05 below the shaft's axis, the last row above the step: its outer edge at x 153.1, 201.4 px out","via":"harvest"}}]},"head_rim_t":{"label":"Thickness of the head at its rim, beside the middle band (the scooped facets' low edge)","kind":"length","measurements":[{"id":"edge","value":0.07,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/radian-talon-safety-selector f09f2e97cdaa (AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement)","scaleRef":"the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5","method":"the long lever edge-on, at the axis' height: the rim's lit band between the inner face and the shadowed scoop, about 64 px on a 1.83x crop","via":"harvest"},"note":"Read by eye on the crop: where the scoop's shadow begins."}]},"shelf_start":{"label":"Where the thumb piece's step rises from the head, from the selector's axis","kind":"length","measurements":[{"id":"edge","value":0.0718,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/radian-talon-safety-selector f09f2e97cdaa (AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement)","scaleRef":"the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5","method":"the long lever edge-on: the step between rows y 760 (.221 thick) and 800 (.294), its middle 65.5 px below the axis","via":"harvest"},"note":"Face-on (the other photo) the step is a point on the lever's centre line, .08 below the long lever's middle and .10 below the short one's, its two shoulders .1 further on."}]},"shelf_point_length":{"label":"Length of the point the thumb piece's step makes, from its tip on the centre line to its two shoulders","kind":"length","measurements":[{"id":"flat","value":0.09,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/radian-talon-safety-selector 21ba32f12fa4 (Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up)","scaleRef":"the shaft in the same photo, on the same table: 207.1 px between its two edges (columns 1340 to 1460, where the white gives way to the shaft's lit edge) taken as .37225, the diameter of the Army's own selector (.shaft_d), which turns in the same .376 hole (std.ar15.selector_hole_d): 556.3 px/in. NOT scaled by the receiver's width: the shaft's shoulders are 534.8 px apart, and as .88 (std.ar15.lower_body_width) they would make its diameter .341, which doesn't turn in that hole","method":"the two levers face-on: the step's point and its shoulders, read on a 2.4x crop: .100 and .186 below the short lever's middle, .079 and .174 below the long one's; the mean of the two differences","via":"harvest"}}]},"head_band_w":{"label":"Width of the head's raised middle band near its top edge","kind":"length","measurements":[{"id":"flat","value":0.13,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/radian-talon-safety-selector 21ba32f12fa4 (Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up)","scaleRef":"the shaft in the same photo, on the same table: 207.1 px between its two edges (columns 1340 to 1460, where the white gives way to the shaft's lit edge) taken as .37225, the diameter of the Army's own selector (.shaft_d), which turns in the same .376 hole (std.ar15.selector_hole_d): 556.3 px/in. NOT scaled by the receiver's width: the shaft's shoulders are 534.8 px apart, and as .88 (std.ar15.lower_body_width) they would make its diameter .341, which doesn't turn in that hole","method":"the short lever's head, .17 above its middle: the band's two edges 36 px either side of the centre line on a 2.4x crop; they spread to the thumb piece's width at its shoulders","via":"harvest"}}]},"shelf_ramp":{"label":"Length of the ramp by which the thumb piece's step rises","kind":"length","measurements":[{"id":"edge","value":0.044,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/radian-talon-safety-selector f09f2e97cdaa (AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement)","scaleRef":"the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5","method":"the long lever edge-on: .221 thick at row y 760 and .294 at y 800, 40 px on: a ramp, not a wall; the short lever face-on shows it as a lit facet on its centre line from y 755 to 815","via":"harvest"}}]},"lever_chamfer":{"label":"Chamfer between a thumb piece's outer face and its sides","kind":"length","measurements":[{"id":"edge","value":0.024,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/radian-talon-safety-selector f09f2e97cdaa (AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement)","scaleRef":"the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5","method":"the short lever face-on, rows y 1040 to 1120: a shadowed band 22 to 25 px wide along its left edge, between its flat outer face and its outline","via":"harvest"},"note":"In the flat-lay photo a lighter band about 12 px wide (.022) runs along each edge of both levers."}]},"shelf_end":{"label":"Where the thumb piece's flat top ends and its taper to the tip begins, from the selector's axis","kind":"length","measurements":[{"id":"edge","value":0.225,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/radian-talon-safety-selector f09f2e97cdaa (AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement)","scaleRef":"the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5","method":"the long lever edge-on: the outer edge holds x 83.4 to 84.3 from y 820 to 920 and falls away below: y 920, 205.5 px below the axis","via":"harvest"}}]},"lever_tip_t":{"label":"Thickness of the long lever's thumb piece near its tip","kind":"length","measurements":[{"id":"edge","value":0.2221,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/radian-talon-safety-selector f09f2e97cdaa (AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement)","scaleRef":"the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5","method":"the long lever edge-on at y 1380 (.729 from the axis), the last row above the end's rake: its outer edge at x 151.8, 202.7 px out","via":"harvest"},"note":"A straight taper from the flat top: .272 at y 1100, .255 at 1200, .239 at 1300."}]},"tip_rake":{"label":"How far the tip's end leans back from the inner face to the outer","kind":"length","measurements":[{"id":"edge","value":0.04,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/radian-talon-safety-selector f09f2e97cdaa (AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement)","scaleRef":"the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5","method":"the long lever's end edge-on: y 1428 at the inner face, 1404 at x 200 and about 1392 at the outer corner","via":"harvest"}}]},"tip_flank_angle":{"label":"Angle of each flank of the lever's pointed tip, from the lever's centre line","kind":"angle","measurements":[{"id":"flat","value":43,"unit":"deg","pm":3,"source":{"type":"photo","photo":"references/radian-talon-safety-selector 21ba32f12fa4 (Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up)","scaleRef":"the shaft in the same photo, on the same table: 207.1 px between its two edges (columns 1340 to 1460, where the white gives way to the shaft's lit edge) taken as .37225, the diameter of the Army's own selector (.shaft_d), which turns in the same .376 hole (std.ar15.selector_hole_d): 556.3 px/in. NOT scaled by the receiver's width: the shaft's shoulders are 534.8 px apart, and as .88 (std.ar15.lower_body_width) they would make its diameter .341, which doesn't turn in that hole","method":"the long lever's width over its last rows (112.4 px at y 1210, 56.7 at 1240): 1.86 px a row, .93 a side; the short lever's the same (114.3 at y 1110, 60.2 at 1140)","via":"harvest"}}]},"tip_flat":{"label":"Width of the blunt end of the lever's point","kind":"length","measurements":[{"id":"flat","value":0.036,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/radian-talon-safety-selector 21ba32f12fa4 (Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up)","scaleRef":"the shaft in the same photo, on the same table: 207.1 px between its two edges (columns 1340 to 1460, where the white gives way to the shaft's lit edge) taken as .37225, the diameter of the Army's own selector (.shaft_d), which turns in the same .376 hole (std.ar15.selector_hole_d): 556.3 px/in. NOT scaled by the receiver's width: the shaft's shoulders are 534.8 px apart, and as .88 (std.ar15.lower_body_width) they would make its diameter .341, which doesn't turn in that hole","method":"the long lever at y 1250, 2 px above its end: 25.5 px wide; the short at y 1150: 33.3 px, 3 px above its end","via":"harvest"}}]},"neck_fillet_r":{"label":"Radius of the hollow between the head and each side of the thumb piece","kind":"length","measurements":[{"id":"flat","value":0.07,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/radian-talon-safety-selector 21ba32f12fa4 (Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up)","scaleRef":"the shaft in the same photo, on the same table: 207.1 px between its two edges (columns 1340 to 1460, where the white gives way to the shaft's lit edge) taken as .37225, the diameter of the Army's own selector (.shaft_d), which turns in the same .376 hole (std.ar15.selector_hole_d): 556.3 px/in. NOT scaled by the receiver's width: the shaft's shoulders are 534.8 px apart, and as .88 (std.ar15.lower_body_width) they would make its diameter .341, which doesn't turn in that hole","method":"the short lever's outline between y 900, where it is still the head's circle (206.1 px wide for a chord of 205.9), and y 955, where its sides run straight: the hollow leaves the circle .15 below the axis and meets the side .25 below it, as a radius of .07 does","via":"harvest"}}]},"stud_hole_d":{"label":"Diameter of the hole in the head's middle that the retention stud snaps into","kind":"length","measurements":[{"id":"edge","value":0.059,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/radian-talon-safety-selector f09f2e97cdaa (AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement)","scaleRef":"the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5","method":"the short lever face-on: the dark hole at (1617, 724), about 54 px across and down","via":"harvest"}}]},"grooves":{"label":"Grooves along each side face of a thumb piece","kind":"count","measurements":[{"id":"edge","value":3,"unit":"count","source":{"type":"photo","photo":"references/radian-talon-safety-selector f09f2e97cdaa (AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement)","scaleRef":"none (a count)","method":"counted on the long lever's side face, the whole face in view: three dark lines along it at rows y 1000, 1100, 1200 and 1300","via":"harvest"},"note":"Primary Arms' two three-quarter views (596f7f263a07, 8d3b958078ae) show three on each side face of both levers."}]},"groove_pitch":{"label":"Distance from one groove to the next","kind":"length","measurements":[{"id":"edge","value":0.0608,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/radian-talon-safety-selector f09f2e97cdaa (AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement)","scaleRef":"the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5","method":"the three grooves' shadowed walls on row y 1100: x 179, 234 and 290, 55.5 px apart (the same on rows 1000, 1200 and 1300)","via":"harvest"}}]},"groove_first":{"label":"The first groove's middle, in from the thumb piece's outer face","kind":"length","measurements":[{"id":"edge","value":0.08,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/radian-talon-safety-selector f09f2e97cdaa (AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement)","scaleRef":"the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5","method":"row y 1100: the outer edge at x 106.3, the first groove at 179, 72.7 px (72.4 on row 1000): the grooves run parallel to the outer face","via":"harvest"}}]},"groove_width":{"label":"Width of each groove","kind":"length","measurements":[{"id":"edge","value":0.026,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/radian-talon-safety-selector f09f2e97cdaa (AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement)","scaleRef":"the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5","method":"a groove's shadowed wall and its lit wall together on row y 1100: 21 to 27 px","via":"harvest"},"note":"A round-ended cut (a ball mill's): its depth isn't seen, and it is drawn as half its width."}]},"groove_start":{"label":"Where the first two grooves begin, from the selector's axis","kind":"length","measurements":[{"id":"edge","value":0.182,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/radian-talon-safety-selector f09f2e97cdaa (AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement)","scaleRef":"the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5","method":"the two outer grooves' rounded upper ends at y 880, 166 px below the axis; the third, nearest the receiver, begins at y 938 (.245)","via":"harvest"}}]},"groove_end_from_tip":{"label":"Where the grooves end, short of the lever's tip","kind":"length","measurements":[{"id":"edge","value":0.096,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/radian-talon-safety-selector f09f2e97cdaa (AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement)","scaleRef":"the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5","method":"the three grooves' lower ends at y 1340, 88 px above the long lever's tip at its inner face (y 1428)","via":"harvest"}}]},"head_groove_w":{"label":"Width of the groove down the head's outer face, from its top edge to the stud's hole","kind":"length","measurements":[{"id":"flat","value":0.042,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/radian-talon-safety-selector 21ba32f12fa4 (Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up)","scaleRef":"the shaft in the same photo, on the same table: 207.1 px between its two edges (columns 1340 to 1460, where the white gives way to the shaft's lit edge) taken as .37225, the diameter of the Army's own selector (.shaft_d), which turns in the same .376 hole (std.ar15.selector_hole_d): 556.3 px/in. NOT scaled by the receiver's width: the shaft's shoulders are 534.8 px apart, and as .88 (std.ar15.lower_body_width) they would make its diameter .341, which doesn't turn in that hole","method":"the short lever's head, .17 above its middle: the groove's two walls 23 px apart on a 2.4x crop; they close toward the hole","via":"harvest"}}]}}},{"subject":"reptilia-aus-30mm-mount","title":"Reptilia AUS™ MOUNT - 30MM DIAMETER - 39MM HEIGHT","dimensions":{"optical_axis_above_rail":{"label":"Ring axis above the rail's top","kind":"length","measurements":[{"id":"maker","value":39,"unit":"mm","stated":"39mm (1.54 inch) bore height","source":{"type":"spec","publisher":"manufacturer","name":"Reptilia, AUS™ MOUNT - 30MM DIAMETER - 39MM HEIGHT (product page)","url":"https://reptiliacorp.com/product/aus-optic-mount-30mm-diameter-39mm-height/","retrieved":"2026-10-13","via":"harvest"}},{"id":"milgear","value":39,"unit":"mm","stated":"Height: 39mm (1.54\")","source":{"type":"spec","publisher":"retailer","name":"Milgear (Finland), Reptilia AUS One-piece Scope Mount - 30 mm - Picatinny - Black (specifications)","url":"https://milgear.fi/en/product/reptilia-aus-one-piece-scope-mount-30-mm-picatinny-black/56909","retrieved":"2026-10-13","via":"harvest"}}],"adopt":{"from":"maker","reason":"The maker's own figure; a seller repeats it."},"note":"The maker's word is \"bore height\"; what it is measured from isn't said on its page. Taken from the rail's top: in the launch photo of the mount with a scope in it the tube's centre stands 38.9 mm above the mount's underside between its clamp bosses, at the scale the mount's length sets."},"ring_bore":{"label":"Tube diameter the rings are bored for","kind":"length","measurements":[{"id":"maker","value":30,"unit":"mm","stated":"30mm diameter bore","source":{"type":"spec","publisher":"manufacturer","name":"Reptilia, AUS™ MOUNT - 30MM DIAMETER - 39MM HEIGHT (product page)","url":"https://reptiliacorp.com/product/aus-optic-mount-30mm-diameter-39mm-height/","retrieved":"2026-10-13","via":"harvest"}},{"id":"milgear","value":30,"unit":"mm","stated":"Pipe diameter: 30 mm","source":{"type":"spec","publisher":"retailer","name":"Milgear (Finland), Reptilia AUS One-piece Scope Mount - 30 mm - Picatinny - Black (specifications)","url":"https://milgear.fi/en/product/reptilia-aus-one-piece-scope-mount-30-mm-picatinny-black/56909","retrieved":"2026-10-13","via":"harvest"}}],"adopt":{"from":"maker","reason":"The maker's own figure; a seller repeats it. It is engraved on the mount's right side as well: \"30MM Ø · 39MM HEIGHT\" (the maker's on-rifle picture, 1c9910ef03b6)."}},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"maker","value":158,"unit":"g","stated":"158 grams","source":{"type":"spec","publisher":"manufacturer","name":"Reptilia, AUS™ MOUNT - 30MM DIAMETER - 39MM HEIGHT (product page)","url":"https://reptiliacorp.com/product/aus-optic-mount-30mm-diameter-39mm-height/","retrieved":"2026-10-13","via":"harvest"}},{"id":"milgear","value":158,"unit":"g","stated":"Weight: 158g","source":{"type":"spec","publisher":"retailer","name":"Milgear (Finland), Reptilia AUS One-piece Scope Mount - 30 mm - Picatinny - Black (specifications)","url":"https://milgear.fi/en/product/reptilia-aus-one-piece-scope-mount-30-mm-picatinny-black/56909","retrieved":"2026-10-13","via":"harvest"}}],"adopt":{"from":"maker","reason":"The maker's own figure; a seller repeats it."},"note":"KYGUNCO's \"Weight 3 lb\" and AR15Discounts' 4 oz are shipping figures, not the mount's."},"objective_clear":{"label":"Largest objective that clears a flat-top rail in it","kind":"length","measurements":[{"id":"maker","value":77,"unit":"mm","stated":"Up to 77mm objective will clear flat-top Picatinny","source":{"type":"spec","publisher":"manufacturer","name":"Reptilia, AUS™ MOUNT - 30MM DIAMETER - 39MM HEIGHT (product page)","url":"https://reptiliacorp.com/product/aus-optic-mount-30mm-diameter-39mm-height/","retrieved":"2026-10-13","via":"harvest"}}],"note":"Half of it, 38.5 mm, is under the 39 mm the rings' axis stands above the rail: the maker's two figures agree."},"overall_length":{"label":"Overall length (front ring's front face to the tail's end)","kind":"length","measurements":[{"id":"milgear","value":135,"unit":"mm","pm":0.5,"stated":"Dimensions: 135 x 52 x 45 mm","source":{"type":"spec","publisher":"retailer","name":"Milgear (Finland), Reptilia AUS One-piece Scope Mount - 30 mm - Picatinny - Black (specifications)","url":"https://milgear.fi/en/product/reptilia-aus-one-piece-scope-mount-30-mm-picatinny-black/56909","retrieved":"2026-10-13","via":"harvest"},"note":"The first of three figures the shop doesn't label. Its third, 45 mm, is the mount's width across its rings as the maker's views from above and below have it (ring_width, 44.6 mm). Its second, 52 mm, is no height of the mount that the side views show (56.4 mm from the rail's top to the caps' tops, 62.5 from the jaws' feet): unexplained."},{"id":"scope-photo","value":5.328,"unit":"in","pm":0.07,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 4583eabd46bb (Soldier Systems, stkl3546-2.jpg: the clear mount with a Vortex scope in it, straight left side, 640 x 427)","scaleRef":"the maker's bore height: the tube's centre (rows 177.9 and 245.5 where the tube stands clear ahead of the turret, 177.8 and 244.7 behind it: 211.5) above the mount's underside between its clamp bosses (row 300.2), 88.7 px for optical_axis_above_rail = 1.5354 in: 57.77 px/in","method":"the mount's silhouette from its front ring's front face (column 131.7) to its tail's end (439.5): 307.8 px. The ± is a pixel in the 88.7. By the tube's own width there (67.3 px for 30 mm) the same length reads 5.40 in: a dark tube on white reads thin, and it does by 1.6% at this scale","via":"harvest"}}],"adopt":{"from":"milgear","reason":"A published figure, and the finer one; the launch photo, scaled by the maker's bore height, reads the same length within a quarter of a percent, and the shop's third figure is the width the plan views read."},"note":"No page of the maker's gives a length. This one sets the scale of every outline and reading of the mount."},"tail_behind_rear_bolt":{"label":"Tail's end behind the rear cross bolt","kind":"length","measurements":[{"id":"left","value":0.66,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 65d1a1c3c68d (Soldier Systems, the launch post's stkl3530-3.jpg: the clear mount alone, straight left side, 640 x 427)","scaleRef":"the mount's overall length, overall_length = 5.315 in (135 mm), over the silhouette's 555.67 px (its front ring's front face at column 54.81, its tail's end at 610.48, each at the 50% level): 104.55 px/in. Checked in the photo of the same mount with a scope in it (4583eabd46bb): at that scale the tube's centre stands 1.532 in (38.9 mm) above the underside between the bosses, for the maker's 39 mm","method":"the rear bolt's head (the dark disc's centre of mass, column 541.45) to the tail's end (610.48)","via":"harvest"}},{"id":"right","value":0.675,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 74ebf1685688 (Soldier Systems, stkl3532-5.jpg: the clear mount alone, right side, 640 x 427; taken from about 4 degrees above)","scaleRef":"the mount's overall length, overall_length = 5.315 in, over the silhouette's 543.47 px (columns 47.18 to 590.65): 102.25 px/in","method":"the rear clamp's middle (columns 76.0 to 156.4 on row 335: 116.2) to the tail's end (47.18)","via":"harvest"}}],"adopt":{"from":"left","reason":"The view the outline is traced from, and the bolt's own head; the other side, by the clamp the bolt draws, is within 0.015."}},"front_face_x":{"label":"Front ring's front face ahead of the rear cross bolt","kind":"length","measurements":[{"id":"derived","value":4.655,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.overall_length} - {.tail_behind_rear_bolt}","via":"harvest"}}],"note":"The left view reads it directly at 4.655 (column 54.81 from the rear bolt's head at 541.45), the right view 4.640."},"clamp_bolt_spacing":{"label":"Cross bolts, centre to centre","kind":"length","measurements":[{"id":"left","value":2.411,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 65d1a1c3c68d (Soldier Systems, the launch post's stkl3530-3.jpg: the clear mount alone, straight left side, 640 x 427)","scaleRef":"the mount's overall length, overall_length = 5.315 in (135 mm), over the silhouette's 555.67 px (its front ring's front face at column 54.81, its tail's end at 610.48, each at the 50% level): 104.55 px/in. Checked in the photo of the same mount with a scope in it (4583eabd46bb): at that scale the tube's centre stands 1.532 in (38.9 mm) above the underside between the bosses, for the maker's 39 mm","method":"the two bolt heads' centres of mass (the dark discs at columns 289.33 and 541.45): 252.12 px. The heads stand on the near face, nearer the lens than the mount's middle, and read a little large for it","via":"harvest"}},{"id":"right","value":2.394,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 74ebf1685688 (Soldier Systems, stkl3532-5.jpg: the clear mount alone, right side, 640 x 427; taken from about 4 degrees above)","scaleRef":"the mount's overall length, overall_length = 5.315 in, over the silhouette's 543.47 px (columns 47.18 to 590.65): 102.25 px/in","method":"the two clamps' middles on row 335 (116.2 and 360.95): 244.75 px","via":"harvest"}},{"id":"underside","value":2.418,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount c306082280c1 (Reptilia, ...CLEAR-ALONE-BOTTOMFOR-SITE.jpg: the clear mount straight from below, 1000 x 1000)","scaleRef":"the mount's overall length, overall_length = 5.315 in, over the underside's 895.0 px (columns 52.4 to 947.4): 168.4 px/in in the underside's plane; the rings, an inch and a half further from the lens, by the cap screws' spacing (0.489 in over 78.7 px: 160.9 px/in)","method":"the two bolts lying across the underside, each the middle of its dark bar at the 90 level on rows 470 to 530 (424.4 and 831.5 at the edges 405.9/442.9 and 811.9/849.2): 407.1 px. In the underside's own plane","via":"harvest"}},{"id":"slots","value":2.364,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"6 * {std.picatinny.slot_pitch}","via":"harvest"},"note":"What the spacing must be if both bolts lie in the middle of a slot each, six apart: kept beside the readings so that the conflict shows (2026-10-19, the detail pass). No view on file or found has the mount on a rail square on: the maker's and the shops' pictures of it on a rifle are the one picture from the front right and above, the launch post's carbine is 640 px wide, and the one photograph of the flat dark earth mount (Silencer Shop's, 0bf480654d9e) is from the front left and above. Searched 2026-10-19: no review, no owner's picture with a rail."}],"adopt":{"from":"left","reason":"The view the outline is traced from; three views, three scales' worth of the one length, within 0.024 of each other. The six slots' 2.364 is kept as the other reading of the same thing: the readings are 0.03 to 0.056 over it, the scale they share is the shop's unlabelled 135 mm (checked by the bore height and the rings' width), and a bolt half the slot's width across would lie in its slot either way. A straight side view with a rail in it would settle it."},"note":"NOT a whole number of rail slots: six of the standard's pitch are 2.364 in, and the three readings are 0.03 to 0.054 over it (6.1 slots). The pitch was the check, not the scale: scaled by six slots the mount would be 132.3 mm long for a published 135, and its rings' axis 38.2 mm above its underside for the maker's 39. What lies in a slot must fit one: the recoil lug midway between the bolts does (lug_length), and the bolts have 0.2 in of slot each to be 0.024 off its middle in, if they are as thin as that leaves (clamp_bolt_shank_d: not read)."},"clamp_bolt_head_d":{"label":"Cross bolt's head, its diameter","kind":"length","measurements":[{"id":"left","value":0.383,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 65d1a1c3c68d (Soldier Systems, the launch post's stkl3530-3.jpg: the clear mount alone, straight left side, 640 x 427)","scaleRef":"the mount's overall length, overall_length = 5.315 in (135 mm), over the silhouette's 555.67 px (its front ring's front face at column 54.81, its tail's end at 610.48, each at the 50% level): 104.55 px/in. Checked in the photo of the same mount with a scope in it (4583eabd46bb): at that scale the tube's centre stands 1.532 in (38.9 mm) above the underside between the bosses, for the maker's 39 mm","method":"each dark disc's extent (columns 270 to 309 and 522 to 562, rows 318 to 357): 40 px","via":"harvest"}}],"note":"A slot across a hex socket (\"either a 5/32 hex or a flat blade driver\"). The maker: tightened \"to sit flush with the body of the mount\": drawn flush with its boss's face."},"clamp_bolt_axis_above_rail":{"label":"Cross bolt's axis above the rail's top","kind":"length","measurements":[{"id":"left","value":0,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 65d1a1c3c68d (Soldier Systems, the launch post's stkl3530-3.jpg: the clear mount alone, straight left side, 640 x 427)","scaleRef":"the mount's overall length, overall_length = 5.315 in (135 mm), over the silhouette's 555.67 px (its front ring's front face at column 54.81, its tail's end at 610.48, each at the 50% level): 104.55 px/in. Checked in the photo of the same mount with a scope in it (4583eabd46bb): at that scale the tube's centre stands 1.532 in (38.9 mm) above the underside between the bosses, for the maker's 39 mm","method":"the two heads' centres (rows 337.2 and 338.5) against the underside between the bosses (the silhouette's lower edge there, row 338.0)","via":"harvest"}}],"note":"On the underside's own level, within a pixel: half of each bolt is under the rail's top, in a slot."},"clamp_bolt_shank_d":{"label":"Cross bolt's shank, its diameter","kind":"length","measurements":[],"note":"Not read. The view from below shows each bolt as a dark bar 37 px across (0.22 in) with a glint down its middle: wider than a rail's slot (0.206), so the bar is the groove the bolt lies in with its shadow, not the bolt. The shanks aren't drawn across the rail's place."},"clamp_bolt_end_d":{"label":"Cross bolt's end in the clamp's face, its diameter","kind":"length","measurements":[{"id":"right","value":0.166,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 74ebf1685688 (Soldier Systems, stkl3532-5.jpg: the clear mount alone, right side, 640 x 427; taken from about 4 degrees above)","scaleRef":"the mount's overall length, overall_length = 5.315 in, over the silhouette's 543.47 px (columns 47.18 to 590.65): 102.25 px/in","method":"the dark round in the rear clamp's face (columns 157 to 175): 17 px","via":"harvest"}}]},"lug_x":{"label":"Recoil lug, its middle ahead of the rear cross bolt","kind":"length","measurements":[{"id":"underside","value":1.214,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount c306082280c1 (Reptilia, ...CLEAR-ALONE-BOTTOMFOR-SITE.jpg: the clear mount straight from below, 1000 x 1000)","scaleRef":"the mount's overall length, overall_length = 5.315 in, over the underside's 895.0 px (columns 52.4 to 947.4): 168.4 px/in in the underside's plane; the rings, an inch and a half further from the lens, by the cap screws' spacing (0.489 in over 78.7 px: 160.9 px/in)","method":"the lug's middle (column 627.5, between the edges of the raised bar at 611 and 644) from the rear bolt's bar (831.5): 204.4 px. Midway between the two bolts (628.0) within half a pixel","via":"harvest"}},{"id":"right","value":1.21,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 74ebf1685688 (Soldier Systems, stkl3532-5.jpg: the clear mount alone, right side, 640 x 427; taken from about 4 degrees above)","scaleRef":"the mount's overall length, overall_length = 5.315 in, over the silhouette's 543.47 px (columns 47.18 to 590.65): 102.25 px/in","method":"the lug where it hangs under the base (columns 229.4 to 250.4 on row 325: 239.9) from the rear clamp's middle (116.2)","via":"harvest"}}],"adopt":{"from":"underside","reason":"In the underside's own plane, and sharp; the side view agrees within 0.004."},"note":"A fixed bar across the underside, the body's own metal (the anodize's colour in every picture), hanging into one slot of the rail: what seats the mount along the rail. The maker's installation sheet: \"Place the AUS Mount on the 1913 rail with clamps loose, and apply a slight forward pressure toward muzzle\"."},"rail_index_x":{"label":"The slot's middle the mount is counted from, ahead of the rear cross bolt","kind":"length","measurements":[{"id":"derived","value":0.032,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{.lug_x} - 3 * {std.picatinny.slot_pitch}","via":"harvest"}}],"note":"The lug lies in a slot, so the slot three behind it has its middle this far ahead of the rear cross bolt, and the slot three ahead of it as far behind the front one: that is where the app's slot number puts the mount (the rail_clamp anchor)."},"lug_length":{"label":"Recoil lug, its length along the rail","kind":"length","measurements":[{"id":"underside","value":0.2,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount c306082280c1 (Reptilia, ...CLEAR-ALONE-BOTTOMFOR-SITE.jpg: the clear mount straight from below, 1000 x 1000)","scaleRef":"the mount's overall length, overall_length = 5.315 in, over the underside's 895.0 px (columns 52.4 to 947.4): 168.4 px/in in the underside's plane; the rings, an inch and a half further from the lens, by the cap screws' spacing (0.489 in over 78.7 px: 160.9 px/in)","method":"the raised bar's width on row 500 (the dark edges at columns 611 and 644, a shadow's width each): 33 to 34 px","via":"harvest"}},{"id":"right","value":0.206,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 74ebf1685688 (Soldier Systems, stkl3532-5.jpg: the clear mount alone, right side, 640 x 427; taken from about 4 degrees above)","scaleRef":"the mount's overall length, overall_length = 5.315 in, over the silhouette's 543.47 px (columns 47.18 to 590.65): 102.25 px/in","method":"where it hangs under the base, row 325: columns 229.37 to 250.43","via":"harvest"}}],"adopt":{"from":"underside","reason":"In its own plane; the side view agrees."},"note":"A slot of the rail is 0.206 in wide (std.picatinny.slot_width): it fills one."},"lug_width":{"label":"Recoil lug, its length across the rail","kind":"length","measurements":[{"id":"underside","value":0.63,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount c306082280c1 (Reptilia, ...CLEAR-ALONE-BOTTOMFOR-SITE.jpg: the clear mount straight from below, 1000 x 1000)","scaleRef":"the mount's overall length, overall_length = 5.315 in, over the underside's 895.0 px (columns 52.4 to 947.4): 168.4 px/in in the underside's plane; the rings, an inch and a half further from the lens, by the cap screws' spacing (0.489 in over 78.7 px: 160.9 px/in)","method":"the raised bar from end to end up column 627 (rows 452 to 558): 106 px","via":"harvest"}}],"note":"Shorter than the rail's top flat is wide (0.656): it doesn't reach the rail's sides."},"lug_depth":{"label":"Recoil lug, how far it hangs under the base","kind":"length","measurements":[{"id":"left","value":0.115,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 65d1a1c3c68d (Soldier Systems, the launch post's stkl3530-3.jpg: the clear mount alone, straight left side, 640 x 427)","scaleRef":"the mount's overall length, overall_length = 5.315 in (135 mm), over the silhouette's 555.67 px (its front ring's front face at column 54.81, its tail's end at 610.48, each at the 50% level): 104.55 px/in. Checked in the photo of the same mount with a scope in it (4583eabd46bb): at that scale the tube's centre stands 1.532 in (38.9 mm) above the underside between the bosses, for the maker's 39 mm","method":"the silhouette's lower edge under the lug (row 350) against the underside beside it (338.0): 12 px; the right view reads 12 px at its scale too (0.117)","via":"harvest"}}],"note":"A slot is 0.118 in deep (std.picatinny.slot_depth): with the underside on the rail's top the lug comes within 0.003 of its floor."},"ring_rear_x":{"label":"Rear ring, its middle ahead of the rear cross bolt","kind":"length","measurements":[{"id":"left","value":0.642,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 65d1a1c3c68d (Soldier Systems, the launch post's stkl3530-3.jpg: the clear mount alone, straight left side, 640 x 427)","scaleRef":"the mount's overall length, overall_length = 5.315 in (135 mm), over the silhouette's 555.67 px (its front ring's front face at column 54.81, its tail's end at 610.48, each at the 50% level): 104.55 px/in. Checked in the photo of the same mount with a scope in it (4583eabd46bb): at that scale the tube's centre stands 1.532 in (38.9 mm) above the underside between the bosses, for the maker's 39 mm","method":"the rear ring's near face on rows 157 to 190 (columns 434.0 to 514.7: beside it, to 422.4, the far wall of its bore shows): its middle, 474.35, from the rear bolt's head (541.45)","via":"harvest"}},{"id":"right","value":0.614,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 74ebf1685688 (Soldier Systems, stkl3532-5.jpg: the clear mount alone, right side, 640 x 427; taken from about 4 degrees above)","scaleRef":"the mount's overall length, overall_length = 5.315 in, over the silhouette's 543.47 px (columns 47.18 to 590.65): 102.25 px/in","method":"the rear ring's near face (columns 139.0 to 219.0): its middle from the rear clamp's middle (116.2)","via":"harvest"}}],"adopt":{"from":"left","reason":"The view the outline is traced from; the other side is within its ±."},"note":"A ring's near face stands 0.9 in nearer the lens than the mount's middle, and the lens was near enough for each ring's far bore wall to show beside its near face (7 to 8 px): what that leaves open is in the ±."},"ring_front_x":{"label":"Front ring, its middle ahead of the rear cross bolt","kind":"length","measurements":[{"id":"left","value":4.264,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 65d1a1c3c68d (Soldier Systems, the launch post's stkl3530-3.jpg: the clear mount alone, straight left side, 640 x 427)","scaleRef":"the mount's overall length, overall_length = 5.315 in (135 mm), over the silhouette's 555.67 px (its front ring's front face at column 54.81, its tail's end at 610.48, each at the 50% level): 104.55 px/in. Checked in the photo of the same mount with a scope in it (4583eabd46bb): at that scale the tube's centre stands 1.532 in (38.9 mm) above the underside between the bosses, for the maker's 39 mm","method":"the front ring's near face (columns 54.8 to 136.5): its middle, 95.65, from the rear bolt's head (541.45)","via":"harvest"}},{"id":"right","value":4.251,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 74ebf1685688 (Soldier Systems, stkl3532-5.jpg: the clear mount alone, right side, 640 x 427; taken from about 4 degrees above)","scaleRef":"the mount's overall length, overall_length = 5.315 in, over the silhouette's 543.47 px (columns 47.18 to 590.65): 102.25 px/in","method":"the front ring's near face (columns 511.0 to 590.8): its middle from the rear clamp's middle (116.2)","via":"harvest"}}],"adopt":{"from":"left","reason":"The view the outline is traced from; the other side is within 0.013."}},"ring_length":{"label":"Each ring's length along the tube (face to face)","kind":"length","measurements":[{"id":"left","value":0.777,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 65d1a1c3c68d (Soldier Systems, the launch post's stkl3530-3.jpg: the clear mount alone, straight left side, 640 x 427)","scaleRef":"the mount's overall length, overall_length = 5.315 in (135 mm), over the silhouette's 555.67 px (its front ring's front face at column 54.81, its tail's end at 610.48, each at the 50% level): 104.55 px/in. Checked in the photo of the same mount with a scope in it (4583eabd46bb): at that scale the tube's centre stands 1.532 in (38.9 mm) above the underside between the bosses, for the maker's 39 mm","method":"each ring's near face on rows 157 to 190: 81.7 px (front) and 80.7 px (rear). The right view reads 0.782 and 0.780 at its scale. A near face stands nearer the lens than the mount's middle and reads up to 2% long","via":"harvest"}}]},"ring_width":{"label":"Rings, across their side flats","kind":"length","measurements":[{"id":"plan","value":1.757,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount bf5ec607d063 (Reptilia, ...CLEAR-ALONE-TOPFOR-SITE-copy-1.jpg: the clear mount straight from above, 1000 x 1000) and references/reptilia-aus-30mm-mount c306082280c1 (Reptilia, ...CLEAR-ALONE-BOTTOMFOR-SITE.jpg: the clear mount straight from below, 1000 x 1000)","scaleRef":"the ring cap screws' spacing along the tube as the left side view has it (ring_screw_spacing, 0.489 in) over the 84 px between the screws' heads here: 171.8 px/in at the heads' depth; the base, an inch and a half further from the lens, by the two cross bolts' heads as the left view has them (2.411 in over 384.5 px: 159.4 px/in). From below: the mount's overall length, overall_length = 5.315 in, over the underside's 895.0 px (columns 52.4 to 947.4): 168.4 px/in in the underside's plane; the rings, an inch and a half further from the lens, by the cap screws' spacing (0.489 in over 78.7 px: 160.9 px/in)","method":"the front ring from side to side: 302.1 px from above (rows 358.3 to 660.4 up column 135: 1.758 in at the heads' depth) and 280.3 px from below (359.4 to 639.8: 1.755 in at the screws' ends' depth)","via":"harvest"}},{"id":"milgear","value":45,"unit":"mm","pm":0.5,"stated":"Dimensions: 135 x 52 x 45 mm","source":{"type":"spec","publisher":"retailer","name":"Milgear (Finland), Reptilia AUS One-piece Scope Mount - 30 mm - Picatinny - Black (specifications)","url":"https://milgear.fi/en/product/reptilia-aus-one-piece-scope-mount-30-mm-picatinny-black/56909","retrieved":"2026-10-13","via":"harvest"},"note":"The third of the shop's three unlabelled figures."}],"adopt":{"from":"plan","reason":"Two views of the ring itself, from above and from below, within 0.003 of each other; the shop's figure doesn't say what it is of, and is 0.4 mm from this."}},"ring_top_above_rail":{"label":"Ring caps' top above the rail's top","kind":"length","measurements":[{"id":"left","value":2.222,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 65d1a1c3c68d (Soldier Systems, the launch post's stkl3530-3.jpg: the clear mount alone, straight left side, 640 x 427)","scaleRef":"the mount's overall length, overall_length = 5.315 in (135 mm), over the silhouette's 555.67 px (its front ring's front face at column 54.81, its tail's end at 610.48, each at the 50% level): 104.55 px/in. Checked in the photo of the same mount with a scope in it (4583eabd46bb): at that scale the tube's centre stands 1.532 in (38.9 mm) above the underside between the bosses, for the maker's 39 mm","method":"the caps' top edge (row 105.7 on both rings) above the underside between the bosses (338.0): 232.3 px. The right view: 227.3 px at its scale, 2.223","via":"harvest"}}],"note":"0.687 in above the rings' axis: 0.096 in of cap over a 30 mm tube."},"ring_top_flat_width":{"label":"Ring caps' top flat, across","kind":"length","measurements":[{"id":"left","value":0.8,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 65d1a1c3c68d (Soldier Systems, the launch post's stkl3530-3.jpg: the clear mount alone, straight left side, 640 x 427)","scaleRef":"the mount's overall length, overall_length = 5.315 in (135 mm), over the silhouette's 555.67 px (its front ring's front face at column 54.81, its tail's end at 610.48, each at the 50% level): 104.55 px/in. Checked in the photo of the same mount with a scope in it (4583eabd46bb): at that scale the tube's centre stands 1.532 in (38.9 mm) above the underside between the bosses, for the maker's 39 mm","method":"where the cap screws' bores open on the cap's chamfer: their openings' middle is 0.275 in under the top (row 134.5), on a chamfer that falls 0.395 in from the top flat's edge to the side flat's top; with the screws 0.735 in from the middle (ring_screw_z) and the side flats 0.879, the top flat's edge is 0.40 in from the middle. From above (bf5ec607d063) the brushed band along the cap's middle is 130 to 135 px wide: 0.76 to 0.79 in","via":"harvest"}}]},"ring_flat_top_above_rail":{"label":"Rings' side flats, their top edge above the rail's top","kind":"length","measurements":[{"id":"left","value":1.827,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 65d1a1c3c68d (Soldier Systems, the launch post's stkl3530-3.jpg: the clear mount alone, straight left side, 640 x 427)","scaleRef":"the mount's overall length, overall_length = 5.315 in (135 mm), over the silhouette's 555.67 px (its front ring's front face at column 54.81, its tail's end at 610.48, each at the 50% level): 104.55 px/in. Checked in the photo of the same mount with a scope in it (4583eabd46bb): at that scale the tube's centre stands 1.532 in (38.9 mm) above the underside between the bosses, for the maker's 39 mm","method":"the brightness edge up column 100 between the cap's chamfer and its side flat (row 147)","via":"harvest"}}]},"ring_split_above_rail":{"label":"The line between cap and lower half, above the rail's top","kind":"length","measurements":[{"id":"left","value":1.645,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 65d1a1c3c68d (Soldier Systems, the launch post's stkl3530-3.jpg: the clear mount alone, straight left side, 640 x 427)","scaleRef":"the mount's overall length, overall_length = 5.315 in (135 mm), over the silhouette's 555.67 px (its front ring's front face at column 54.81, its tail's end at 610.48, each at the 50% level): 104.55 px/in. Checked in the photo of the same mount with a scope in it (4583eabd46bb): at that scale the tube's centre stands 1.532 in (38.9 mm) above the underside between the bosses, for the maker's 39 mm","method":"the dark line across each ring's side flat (row 166.0 on both)","via":"harvest"}}],"note":"0.110 in above the rings' axis: the caps are shallower than half a ring. In the photo with a scope in it the line is 8 px above the tube's centre at a scale of 57.9 px/in: 0.14."},"ring_flat_bottom_above_rail":{"label":"Rings' side flats, their bottom edge above the rail's top","kind":"length","measurements":[{"id":"left","value":1.473,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 65d1a1c3c68d (Soldier Systems, the launch post's stkl3530-3.jpg: the clear mount alone, straight left side, 640 x 427)","scaleRef":"the mount's overall length, overall_length = 5.315 in (135 mm), over the silhouette's 555.67 px (its front ring's front face at column 54.81, its tail's end at 610.48, each at the 50% level): 104.55 px/in. Checked in the photo of the same mount with a scope in it (4583eabd46bb): at that scale the tube's centre stands 1.532 in (38.9 mm) above the underside between the bosses, for the maker's 39 mm","method":"the brightness edge up column 100 where the lit side flat ends over the shadowed lower chamfer (row 184)","via":"harvest"}}],"note":"0.06 in under the rings' axis: the tube's widest is on the flats."},"ring_neck_top_above_rail":{"label":"Rings' lower chamfer, its foot above the rail's top (where the ring meets its neck)","kind":"length","measurements":[{"id":"left","value":0.887,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 65d1a1c3c68d (Soldier Systems, the launch post's stkl3530-3.jpg: the clear mount alone, straight left side, 640 x 427)","scaleRef":"the mount's overall length, overall_length = 5.315 in (135 mm), over the silhouette's 555.67 px (its front ring's front face at column 54.81, its tail's end at 610.48, each at the 50% level): 104.55 px/in. Checked in the photo of the same mount with a scope in it (4583eabd46bb): at that scale the tube's centre stands 1.532 in (38.9 mm) above the underside between the bosses, for the maker's 39 mm","method":"the lower chamfer's slope carried down to the neck's width (base_width): the cap screws' bores come out of it 0.163 in under the side flat's foot (the ovals' middle, row 201) at 0.735 in from the middle, 0.144 in inside the flat: 48 degrees. Its foot itself is in shadow in both side views","via":"harvest"}}]},"ring_screw_spacing":{"label":"Ring cap screws, the two on a side, centre to centre along the tube","kind":"length","measurements":[{"id":"left","value":0.489,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 65d1a1c3c68d (Soldier Systems, the launch post's stkl3530-3.jpg: the clear mount alone, straight left side, 640 x 427)","scaleRef":"the mount's overall length, overall_length = 5.315 in (135 mm), over the silhouette's 555.67 px (its front ring's front face at column 54.81, its tail's end at 610.48, each at the 50% level): 104.55 px/in. Checked in the photo of the same mount with a scope in it (4583eabd46bb): at that scale the tube's centre stands 1.532 in (38.9 mm) above the underside between the bosses, for the maker's 39 mm","method":"the bores' lower ends on each ring (the dark ovals at columns 70.28 and 121.62, 450.0 and 500.91): 51.3 and 50.9 px","via":"harvest"}}]},"ring_screw_z":{"label":"Ring cap screws, their axes from the mount's middle","kind":"length","measurements":[{"id":"plan","value":0.735,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount bf5ec607d063 (Reptilia, ...CLEAR-ALONE-TOPFOR-SITE-copy-1.jpg: the clear mount straight from above, 1000 x 1000) and references/reptilia-aus-30mm-mount c306082280c1 (Reptilia, ...CLEAR-ALONE-BOTTOMFOR-SITE.jpg: the clear mount straight from below, 1000 x 1000)","scaleRef":"the ring cap screws' spacing along the tube as the left side view has it (ring_screw_spacing, 0.489 in) over the 84 px between the screws' heads here: 171.8 px/in at the heads' depth; the base, an inch and a half further from the lens, by the two cross bolts' heads as the left view has them (2.411 in over 384.5 px: 159.4 px/in). From below: the mount's overall length, overall_length = 5.315 in, over the underside's 895.0 px (columns 52.4 to 947.4): 168.4 px/in in the underside's plane; the rings, an inch and a half further from the lens, by the cap screws' spacing (0.489 in over 78.7 px: 160.9 px/in)","method":"the screws' heads from above (rows 380.1 and 633.0: 126.5 px each side of the middle, 0.736 in) and their bores' lower ends from below (117.7 px each side: 0.731)","via":"harvest"}}],"note":"Four to a cap, upright, outside the tube: each head shows whole from straight above, in a bore that opens on the cap's chamfer, and the bore comes out through the lower half's chamfer under it (an oval from the side, a round from below)."},"ring_screw_bore_d":{"label":"Ring cap screws, the bore each head sits in","kind":"length","measurements":[{"id":"top","value":0.215,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount bf5ec607d063 (Reptilia, ...CLEAR-ALONE-TOPFOR-SITE-copy-1.jpg: the clear mount straight from above, 1000 x 1000)","scaleRef":"the ring cap screws' spacing along the tube as the left side view has it (ring_screw_spacing, 0.489 in) over the 84 px between the screws' heads here: 171.8 px/in at the heads' depth; the base, an inch and a half further from the lens, by the two cross bolts' heads as the left view has them (2.411 in over 384.5 px: 159.4 px/in)","method":"each dark round from above (columns 77 to 114 and three more): 37 px","via":"harvest"}}]},"ring_screw_exit_d":{"label":"Ring cap screws, the bore's lower end in the lower half's chamfer","kind":"length","measurements":[{"id":"left","value":0.185,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 65d1a1c3c68d (Soldier Systems, the launch post's stkl3530-3.jpg: the clear mount alone, straight left side, 640 x 427)","scaleRef":"the mount's overall length, overall_length = 5.315 in (135 mm), over the silhouette's 555.67 px (its front ring's front face at column 54.81, its tail's end at 610.48, each at the 50% level): 104.55 px/in. Checked in the photo of the same mount with a scope in it (4583eabd46bb): at that scale the tube's centre stands 1.532 in (38.9 mm) above the underside between the bosses, for the maker's 39 mm","method":"each oval's width along the tube (columns 61 to 80 and three more): 19 to 20 px; from below they are rounds 28 to 29 px across, 0.18 in","via":"harvest"}}]},"ring_screw_head_d":{"label":"Ring cap screws, their heads","kind":"length","measurements":[{"id":"top","value":0.15,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount bf5ec607d063 (Reptilia, ...CLEAR-ALONE-TOPFOR-SITE-copy-1.jpg: the clear mount straight from above, 1000 x 1000)","scaleRef":"the ring cap screws' spacing along the tube as the left side view has it (ring_screw_spacing, 0.489 in) over the 84 px between the screws' heads here: 171.8 px/in at the heads' depth; the base, an inch and a half further from the lens, by the two cross bolts' heads as the left view has them (2.411 in over 384.5 px: 159.4 px/in)","method":"the darker round inside each bore (columns 83 to 109 and three more): 25 to 26 px","via":"harvest"}}],"note":"\"T15 screws\" (the maker's installation sheet); 15 in-lb, dry."},"ring_screw_head_below_top":{"label":"Ring cap screws, their heads' tops under the cap's top","kind":"length","measurements":[{"id":"assumed","value":0.37,"unit":"in","pm":0.08,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows a head in profile. From straight above each is lit, a little way down its bore; put a tenth of an inch under where the bore opens on the chamfer.","via":"harvest"}}]},"base_width":{"label":"Base, across (the plate over the rail, and each ring's neck)","kind":"length","measurements":[{"id":"plan","value":0.712,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount bf5ec607d063 (Reptilia, ...CLEAR-ALONE-TOPFOR-SITE-copy-1.jpg: the clear mount straight from above, 1000 x 1000) and references/reptilia-aus-30mm-mount c306082280c1 (Reptilia, ...CLEAR-ALONE-BOTTOMFOR-SITE.jpg: the clear mount straight from below, 1000 x 1000)","scaleRef":"the ring cap screws' spacing along the tube as the left side view has it (ring_screw_spacing, 0.489 in) over the 84 px between the screws' heads here: 171.8 px/in at the heads' depth; the base, an inch and a half further from the lens, by the two cross bolts' heads as the left view has them (2.411 in over 384.5 px: 159.4 px/in). From below: the mount's overall length, overall_length = 5.315 in, over the underside's 895.0 px (columns 52.4 to 947.4): 168.4 px/in in the underside's plane; the rings, an inch and a half further from the lens, by the cap screws' spacing (0.489 in over 78.7 px: 160.9 px/in)","method":"between the rings from above (rows 462.4 to 575.7 up columns 260 and 300: 113.3 px, 0.711 in at the base's depth) and from below (444.9 to 565.2: 120.3 px, 0.714)","via":"harvest"}}],"note":"Narrower than the rail's top (0.835): between its clamps the base is a plate lying on the rail, and it reaches under the rail only at the two clamp bosses."},"base_plate_top_above_rail":{"label":"Base plate's top (the ledge under the bridge's lettered web) above the rail's top","kind":"length","measurements":[{"id":"left","value":0.335,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 65d1a1c3c68d (Soldier Systems, the launch post's stkl3530-3.jpg: the clear mount alone, straight left side, 640 x 427)","scaleRef":"the mount's overall length, overall_length = 5.315 in (135 mm), over the silhouette's 555.67 px (its front ring's front face at column 54.81, its tail's end at 610.48, each at the 50% level): 104.55 px/in. Checked in the photo of the same mount with a scope in it (4583eabd46bb): at that scale the tube's centre stands 1.532 in (38.9 mm) above the underside between the bosses, for the maker's 39 mm","method":"the line under the lettered panel between the rings (row 303)","via":"harvest"}}]},"base_top_above_rail":{"label":"Bridge's top between the rings, above the rail's top","kind":"length","measurements":[{"id":"left","value":0.545,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 65d1a1c3c68d (Soldier Systems, the launch post's stkl3530-3.jpg: the clear mount alone, straight left side, 640 x 427)","scaleRef":"the mount's overall length, overall_length = 5.315 in (135 mm), over the silhouette's 555.67 px (its front ring's front face at column 54.81, its tail's end at 610.48, each at the 50% level): 104.55 px/in. Checked in the photo of the same mount with a scope in it (4583eabd46bb): at that scale the tube's centre stands 1.532 in (38.9 mm) above the underside between the bosses, for the maker's 39 mm","method":"the silhouette's upper edge between the rings (row 281.0 from column 167 to 403)","via":"harvest"}}]},"bridge_web_width":{"label":"Bridge's web between the rings (REPTILIA on its left face, the name and size on its right), across","kind":"length","measurements":[{"id":"top","value":0.19,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount bf5ec607d063 (Reptilia, ...CLEAR-ALONE-TOPFOR-SITE-copy-1.jpg: the clear mount straight from above, 1000 x 1000)","scaleRef":"the ring cap screws' spacing along the tube as the left side view has it (ring_screw_spacing, 0.489 in) over the 84 px between the screws' heads here: 171.8 px/in at the heads' depth; the base, an inch and a half further from the lens, by the two cross bolts' heads as the left view has them (2.411 in over 384.5 px: 159.4 px/in)","method":"up column 300 between the rings: the plate's edges at rows 463 and 576, an edge at 502 and the web's shadow from 532: 30 px, about the mount's middle (517 for 519.5)","via":"harvest"}}]},"mount_length":{"label":"Clamp length along the rail (rear boss's rear end to front boss's front end)","kind":"length","measurements":[{"id":"left","value":3.424,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 65d1a1c3c68d (Soldier Systems, the launch post's stkl3530-3.jpg: the clear mount alone, straight left side, 640 x 427)","scaleRef":"the mount's overall length, overall_length = 5.315 in (135 mm), over the silhouette's 555.67 px (its front ring's front face at column 54.81, its tail's end at 610.48, each at the 50% level): 104.55 px/in. Checked in the photo of the same mount with a scope in it (4583eabd46bb): at that scale the tube's centre stands 1.532 in (38.9 mm) above the underside between the bosses, for the maker's 39 mm","method":"the two bosses' ends on rows 345 and 355 (columns 236.4 and 594.4): 358 px","via":"harvest"}}]},"boss_length":{"label":"Each clamp boss (the fixed jaw under a bolt's head), along the rail","kind":"length","measurements":[{"id":"left","value":1.026,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 65d1a1c3c68d (Soldier Systems, the launch post's stkl3530-3.jpg: the clear mount alone, straight left side, 640 x 427)","scaleRef":"the mount's overall length, overall_length = 5.315 in (135 mm), over the silhouette's 555.67 px (its front ring's front face at column 54.81, its tail's end at 610.48, each at the 50% level): 104.55 px/in. Checked in the photo of the same mount with a scope in it (4583eabd46bb): at that scale the tube's centre stands 1.532 in (38.9 mm) above the underside between the bosses, for the maker's 39 mm","method":"rows 345 and 355: columns 236.4 to 343.2 and 486.6 to 594.4 (106.8 and 107.8 px)","via":"harvest"}}]},"boss_outer_z":{"label":"Clamp bosses' outer face, from the mount's middle (the left side)","kind":"length","measurements":[{"id":"plan","value":0.6,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount bf5ec607d063 (Reptilia, ...CLEAR-ALONE-TOPFOR-SITE-copy-1.jpg: the clear mount straight from above, 1000 x 1000) and references/reptilia-aus-30mm-mount c306082280c1 (Reptilia, ...CLEAR-ALONE-BOTTOMFOR-SITE.jpg: the clear mount straight from below, 1000 x 1000)","scaleRef":"the ring cap screws' spacing along the tube as the left side view has it (ring_screw_spacing, 0.489 in) over the 84 px between the screws' heads here: 171.8 px/in at the heads' depth; the base, an inch and a half further from the lens, by the two cross bolts' heads as the left view has them (2.411 in over 384.5 px: 159.4 px/in). From below: the mount's overall length, overall_length = 5.315 in, over the underside's 895.0 px (columns 52.4 to 947.4): 168.4 px/in in the underside's plane; the rings, an inch and a half further from the lens, by the cap screws' spacing (0.489 in over 78.7 px: 160.9 px/in)","method":"how far each boss stands out of the base's side: 41.6 px from above (0.261 in) and 37.7 px from below (0.224), added to half of base_width","via":"harvest"}}]},"jaw_below_rail":{"label":"Clamp bosses' feet under the rail's top","kind":"length","measurements":[{"id":"left","value":0.239,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 65d1a1c3c68d (Soldier Systems, the launch post's stkl3530-3.jpg: the clear mount alone, straight left side, 640 x 427)","scaleRef":"the mount's overall length, overall_length = 5.315 in (135 mm), over the silhouette's 555.67 px (its front ring's front face at column 54.81, its tail's end at 610.48, each at the 50% level): 104.55 px/in. Checked in the photo of the same mount with a scope in it (4583eabd46bb): at that scale the tube's centre stands 1.532 in (38.9 mm) above the underside between the bosses, for the maker's 39 mm","method":"the silhouette's lower edge under each boss (rows 362 to 364) against the underside between them (338.0): 25 px","via":"harvest"}}]},"clamp_length":{"label":"Each steel clamp (right side), along the rail","kind":"length","measurements":[{"id":"right","value":0.78,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 74ebf1685688 (Soldier Systems, stkl3532-5.jpg: the clear mount alone, right side, 640 x 427; taken from about 4 degrees above)","scaleRef":"the mount's overall length, overall_length = 5.315 in, over the silhouette's 543.47 px (columns 47.18 to 590.65): 102.25 px/in","method":"row 335: columns 76.0 to 156.4 and 321.2 to 400.7 (80.4 and 79.4 px)","via":"harvest"}}]},"clamp_outer_z":{"label":"Steel clamps' outer face, from the mount's middle (the right side)","kind":"length","measurements":[{"id":"plan","value":0.64,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount bf5ec607d063 (Reptilia, ...CLEAR-ALONE-TOPFOR-SITE-copy-1.jpg: the clear mount straight from above, 1000 x 1000) and references/reptilia-aus-30mm-mount c306082280c1 (Reptilia, ...CLEAR-ALONE-BOTTOMFOR-SITE.jpg: the clear mount straight from below, 1000 x 1000)","scaleRef":"the ring cap screws' spacing along the tube as the left side view has it (ring_screw_spacing, 0.489 in) over the 84 px between the screws' heads here: 171.8 px/in at the heads' depth; the base, an inch and a half further from the lens, by the two cross bolts' heads as the left view has them (2.411 in over 384.5 px: 159.4 px/in). From below: the mount's overall length, overall_length = 5.315 in, over the underside's 895.0 px (columns 52.4 to 947.4): 168.4 px/in in the underside's plane; the rings, an inch and a half further from the lens, by the cap screws' spacing (0.489 in over 78.7 px: 160.9 px/in)","method":"how far the front clamp stands out of the base's side: 43.5 px from above (0.273 in) and 48.8 px from below (0.290), added to half of base_width","via":"harvest"}}]},"clamp_top_above_rail":{"label":"Steel clamps' top above the rail's top","kind":"length","measurements":[{"id":"right","value":0.2,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 74ebf1685688 (Soldier Systems, stkl3532-5.jpg: the clear mount alone, right side, 640 x 427; taken from about 4 degrees above)","scaleRef":"the mount's overall length, overall_length = 5.315 in, over the silhouette's 543.47 px (columns 47.18 to 590.65): 102.25 px/in","method":"the dark blocks' upper edge (row 294) against the underside between them (316): 22 px, less the 0.016 in the view from above adds to what stands nearest the lens","via":"harvest"}}]},"clamp_below_rail":{"label":"Steel clamps' feet under the rail's top","kind":"length","measurements":[{"id":"right","value":0.25,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 74ebf1685688 (Soldier Systems, stkl3532-5.jpg: the clear mount alone, right side, 640 x 427; taken from about 4 degrees above)","scaleRef":"the mount's overall length, overall_length = 5.315 in, over the silhouette's 543.47 px (columns 47.18 to 590.65): 102.25 px/in","method":"the dark blocks' lower edge (rows 342 to 343) against the underside between them (316): 27 px, less the same 0.016","via":"harvest"}}]},"pocket_front_x":{"label":"Front accessory pocket (two cross holes in a recess, each side), its middle ahead of the rear cross bolt","kind":"length","measurements":[{"id":"left","value":4.225,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 65d1a1c3c68d (Soldier Systems, the launch post's stkl3530-3.jpg: the clear mount alone, straight left side, 640 x 427)","scaleRef":"the mount's overall length, overall_length = 5.315 in (135 mm), over the silhouette's 555.67 px (its front ring's front face at column 54.81, its tail's end at 610.48, each at the 50% level): 104.55 px/in. Checked in the photo of the same mount with a scope in it (4583eabd46bb): at that scale the tube's centre stands 1.532 in (38.9 mm) above the underside between the bosses, for the maker's 39 mm","method":"the middle of the two see-through holes (columns 86.6 and 112.9)","via":"harvest"}},{"id":"right","value":4.18,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 74ebf1685688 (Soldier Systems, stkl3532-5.jpg: the clear mount alone, right side, 640 x 427; taken from about 4 degrees above)","scaleRef":"the mount's overall length, overall_length = 5.315 in, over the silhouette's 543.47 px (columns 47.18 to 590.65): 102.25 px/in","method":"the middle of the two see-through holes (columns 531.1 and 556.2) from the rear clamp's middle","via":"harvest"}}],"adopt":{"from":"left","reason":"The view the outline is traced from. A hole seen through from a near lens shows where the line of sight clears both its ends: the two sides differ by that."}},"pocket_rear_x":{"label":"Rear accessory pocket, its middle ahead of the rear cross bolt","kind":"length","measurements":[{"id":"left","value":0.705,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 65d1a1c3c68d (Soldier Systems, the launch post's stkl3530-3.jpg: the clear mount alone, straight left side, 640 x 427)","scaleRef":"the mount's overall length, overall_length = 5.315 in (135 mm), over the silhouette's 555.67 px (its front ring's front face at column 54.81, its tail's end at 610.48, each at the 50% level): 104.55 px/in. Checked in the photo of the same mount with a scope in it (4583eabd46bb): at that scale the tube's centre stands 1.532 in (38.9 mm) above the underside between the bosses, for the maker's 39 mm","method":"the middle of the two see-through holes (columns 454.7 and 480.7)","via":"harvest"}},{"id":"right","value":0.676,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 74ebf1685688 (Soldier Systems, stkl3532-5.jpg: the clear mount alone, right side, 640 x 427; taken from about 4 degrees above)","scaleRef":"the mount's overall length, overall_length = 5.315 in, over the silhouette's 543.47 px (columns 47.18 to 590.65): 102.25 px/in","method":"the middle of the two see-through holes (columns 172.6 and 198.1) from the rear clamp's middle","via":"harvest"}}],"adopt":{"from":"left","reason":"The view the outline is traced from; the other side is within its ±."}},"pocket_y":{"label":"Accessory pockets' cross holes, above the rail's top","kind":"length","measurements":[{"id":"left","value":0.448,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 65d1a1c3c68d (Soldier Systems, the launch post's stkl3530-3.jpg: the clear mount alone, straight left side, 640 x 427)","scaleRef":"the mount's overall length, overall_length = 5.315 in (135 mm), over the silhouette's 555.67 px (its front ring's front face at column 54.81, its tail's end at 610.48, each at the 50% level): 104.55 px/in. Checked in the photo of the same mount with a scope in it (4583eabd46bb): at that scale the tube's centre stands 1.532 in (38.9 mm) above the underside between the bosses, for the maker's 39 mm","method":"the four holes' centres (rows 290.9 to 291.4) above the underside (338.0)","via":"harvest"}}],"note":"The holes the maker's ROF mounts and AUS Offset bolt to (\"compatible with all of our existing 30mm ROF line\"): accessories that aren't in the catalog."},"pocket_length":{"label":"Accessory pockets' recess, along the rail","kind":"length","measurements":[{"id":"left","value":0.555,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 65d1a1c3c68d (Soldier Systems, the launch post's stkl3530-3.jpg: the clear mount alone, straight left side, 640 x 427)","scaleRef":"the mount's overall length, overall_length = 5.315 in (135 mm), over the silhouette's 555.67 px (its front ring's front face at column 54.81, its tail's end at 610.48, each at the 50% level): 104.55 px/in. Checked in the photo of the same mount with a scope in it (4583eabd46bb): at that scale the tube's centre stands 1.532 in (38.9 mm) above the underside between the bosses, for the maker's 39 mm","method":"the front recess's ends (columns 69 to 127): 58 px","via":"harvest"}}]},"pocket_height":{"label":"Accessory pockets' recess, its height","kind":"length","measurements":[{"id":"left","value":0.26,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 65d1a1c3c68d (Soldier Systems, the launch post's stkl3530-3.jpg: the clear mount alone, straight left side, 640 x 427)","scaleRef":"the mount's overall length, overall_length = 5.315 in (135 mm), over the silhouette's 555.67 px (its front ring's front face at column 54.81, its tail's end at 610.48, each at the 50% level): 104.55 px/in. Checked in the photo of the same mount with a scope in it (4583eabd46bb): at that scale the tube's centre stands 1.532 in (38.9 mm) above the underside between the bosses, for the maker's 39 mm","method":"the recess's upper and lower edges (rows 273 to 300): 27 px","via":"harvest"}}]},"pocket_hole_spacing":{"label":"Accessory pockets' cross holes, centre to centre","kind":"length","measurements":[{"id":"left","value":0.25,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 65d1a1c3c68d (Soldier Systems, the launch post's stkl3530-3.jpg: the clear mount alone, straight left side, 640 x 427)","scaleRef":"the mount's overall length, overall_length = 5.315 in (135 mm), over the silhouette's 555.67 px (its front ring's front face at column 54.81, its tail's end at 610.48, each at the 50% level): 104.55 px/in. Checked in the photo of the same mount with a scope in it (4583eabd46bb): at that scale the tube's centre stands 1.532 in (38.9 mm) above the underside between the bosses, for the maker's 39 mm","method":"26.3 and 26.0 px on the two pockets; the right view reads 25.1 and 25.5 px at its scale, 0.247","via":"harvest"}}]},"pocket_hole_d":{"label":"Accessory pockets' cross holes, their diameter","kind":"length","measurements":[{"id":"left","value":0.115,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 65d1a1c3c68d (Soldier Systems, the launch post's stkl3530-3.jpg: the clear mount alone, straight left side, 640 x 427)","scaleRef":"the mount's overall length, overall_length = 5.315 in (135 mm), over the silhouette's 555.67 px (its front ring's front face at column 54.81, its tail's end at 610.48, each at the 50% level): 104.55 px/in. Checked in the photo of the same mount with a scope in it (4583eabd46bb): at that scale the tube's centre stands 1.532 in (38.9 mm) above the underside between the bosses, for the maker's 39 mm","method":"each see-through round's extent: 12 px","via":"harvest"}}]},"pocket_depth":{"label":"Accessory pockets' recess, its depth into each side","kind":"length","measurements":[{"id":"assumed","value":0.12,"unit":"in","pm":0.06,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file is square across a pocket. The maker's three-quarter view (eeb891756f2e) has its floor a little way in, with the two holes through it.","via":"harvest"}}]},"tail_width":{"label":"Tail (the block behind the rear ring, over the rear clamp), across","kind":"length","measurements":[{"id":"top","value":0.83,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount bf5ec607d063 (Reptilia, ...CLEAR-ALONE-TOPFOR-SITE-copy-1.jpg: the clear mount straight from above, 1000 x 1000)","scaleRef":"the ring cap screws' spacing along the tube as the left side view has it (ring_screw_spacing, 0.489 in) over the 84 px between the screws' heads here: 171.8 px/in at the heads' depth; the base, an inch and a half further from the lens, by the two cross bolts' heads as the left view has them (2.411 in over 384.5 px: 159.4 px/in)","method":"up column 930, behind the rear clamp (rows 446.7 to 578.5): 131.8 px at the base's depth","via":"harvest"}}],"note":"As wide as the rail's top (0.835)."},"boss_face_length":{"label":"Each clamp boss's outer face, along the rail (its ends are chamfered back to the base)","kind":"length","measurements":[{"id":"underside","value":0.88,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount c306082280c1 (Reptilia, ...CLEAR-ALONE-BOTTOMFOR-SITE.jpg: the clear mount straight from below, 1000 x 1000)","scaleRef":"the mount's overall length, overall_length = 5.315 in, over the underside's 895.0 px (columns 52.4 to 947.4): 168.4 px/in in the underside's plane; the rings, an inch and a half further from the lens, by the cap screws' spacing (0.489 in over 78.7 px: 160.9 px/in)","method":"the front boss's outer edge from below (columns 352 to 500 on row 408): 148 px, for the 182 px it is long against the base (row 430: 333.5 to 515.7)","via":"harvest"}}]},"clamp_face_length":{"label":"Each steel clamp's outer face, along the rail (its ends are chamfered back to the base)","kind":"length","measurements":[{"id":"top","value":0.44,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount bf5ec607d063 (Reptilia, ...CLEAR-ALONE-TOPFOR-SITE-copy-1.jpg: the clear mount straight from above, 1000 x 1000)","scaleRef":"the ring cap screws' spacing along the tube as the left side view has it (ring_screw_spacing, 0.489 in) over the 84 px between the screws' heads here: 171.8 px/in at the heads' depth; the base, an inch and a half further from the lens, by the two cross bolts' heads as the left view has them (2.411 in over 384.5 px: 159.4 px/in)","method":"the front clamp's outer edge from above (columns 422 to 492): 70 px at the base's depth, for the 121 px it is long against the base","via":"harvest"}}]},"ring_corner_chamfer":{"label":"Rings' upright corners (between an end face and a side flat), the chamfer","kind":"length","measurements":[{"id":"top","value":0.055,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount bf5ec607d063 (Reptilia, ...CLEAR-ALONE-TOPFOR-SITE-copy-1.jpg: the clear mount straight from above, 1000 x 1000)","scaleRef":"the ring cap screws' spacing along the tube as the left side view has it (ring_screw_spacing, 0.489 in) over the 84 px between the screws' heads here: 171.8 px/in at the heads' depth; the base, an inch and a half further from the lens, by the two cross bolts' heads as the left view has them (2.411 in over 384.5 px: 159.4 px/in)","method":"the front cap's corners from above: its front edge at column 79.6 on row 365, 71.5 on row 380 and 69.4 on row 400: about 10 px at 45 degrees","via":"harvest"}}]},"pocket_recess_y":{"label":"Accessory pockets' recess, its middle above the rail's top","kind":"length","measurements":[{"id":"left","value":0.49,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 65d1a1c3c68d (Soldier Systems, the launch post's stkl3530-3.jpg: the clear mount alone, straight left side, 640 x 427)","scaleRef":"the mount's overall length, overall_length = 5.315 in (135 mm), over the silhouette's 555.67 px (its front ring's front face at column 54.81, its tail's end at 610.48, each at the 50% level): 104.55 px/in. Checked in the photo of the same mount with a scope in it (4583eabd46bb): at that scale the tube's centre stands 1.532 in (38.9 mm) above the underside between the bosses, for the maker's 39 mm","method":"the recess's upper and lower edges (rows 273 and 300): its middle, row 286.5; the cross holes are 0.045 in under it","via":"harvest"}}]},"clamp_bolt_hex_af":{"label":"Cross bolt's head, the hex socket across its flats","kind":"length","measurements":[{"id":"maker","value":0.15625,"unit":"in","pm":0.001,"stated":"which can be tightened with either a 5/32 hex or a flat blade driver","source":{"type":"spec","publisher":"manufacturer","name":"Reptilia, AUS™ MOUNT - 30MM DIAMETER - 39MM HEIGHT (product page)","url":"https://reptiliacorp.com/product/aus-optic-mount-30mm-diameter-39mm-height/","retrieved":"2026-10-13","via":"harvest"}}],"note":"5/32 in. The installation sheet's tools: \"5/32 hex driver or large flat blade driver\"; 45 in-lb, dry."},"clamp_bolt_head_h":{"label":"Cross bolt's head, its thickness (and the depth of the seat it sits flush in)","kind":"length","measurements":[{"id":"assumed","value":0.1,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows a head from its edge. The maker says only that it sits flush.","via":"harvest"}}]},"under_pocket_width":{"label":"Underside's lightening pockets, across","kind":"length","measurements":[{"id":"underside","value":0.564,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount c306082280c1 (Reptilia, ...CLEAR-ALONE-BOTTOMFOR-SITE.jpg: the clear mount straight from below, 1000 x 1000)","scaleRef":"the mount's overall length, overall_length = 5.315 in, over the underside's 895.0 px (columns 52.4 to 947.4): 168.4 px/in in the underside's plane; the rings, an inch and a half further from the lens, by the cap screws' spacing (0.489 in over 78.7 px: 160.9 px/in)","method":"the three pockets' long edges (rows 455 and 550): 95 px","via":"harvest"}}]},"under_pocket_front_x0":{"label":"Underside pocket (the long one under the bridge, ahead of the front cross bolt), its rear end ahead of the rear cross bolt","kind":"length","measurements":[{"id":"underside","value":2.871,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount c306082280c1 (Reptilia, ...CLEAR-ALONE-BOTTOMFOR-SITE.jpg: the clear mount straight from below, 1000 x 1000)","scaleRef":"the mount's overall length, overall_length = 5.315 in, over the underside's 895.0 px (columns 52.4 to 947.4): 168.4 px/in in the underside's plane; the rings, an inch and a half further from the lens, by the cap screws' spacing (0.489 in over 78.7 px: 160.9 px/in)","method":"the pocket's rear end, column 348 on a gridded enlargement, from the rear bolt's bar (831.5)","via":"harvest"}}]},"under_pocket_front_x1":{"label":"Underside pocket (the long one under the bridge, ahead of the front cross bolt), its front end ahead of the rear cross bolt","kind":"length","measurements":[{"id":"underside","value":3.863,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount c306082280c1 (Reptilia, ...CLEAR-ALONE-BOTTOMFOR-SITE.jpg: the clear mount straight from below, 1000 x 1000)","scaleRef":"the mount's overall length, overall_length = 5.315 in, over the underside's 895.0 px (columns 52.4 to 947.4): 168.4 px/in in the underside's plane; the rings, an inch and a half further from the lens, by the cap screws' spacing (0.489 in over 78.7 px: 160.9 px/in)","method":"the pocket's front end, column 181 on a gridded enlargement, from the rear bolt's bar (831.5)","via":"harvest"}}]},"under_pocket_mid_x0":{"label":"Underside pocket (between the front cross bolt and the lug), its rear end ahead of the rear cross bolt","kind":"length","measurements":[{"id":"underside","value":1.565,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount c306082280c1 (Reptilia, ...CLEAR-ALONE-BOTTOMFOR-SITE.jpg: the clear mount straight from below, 1000 x 1000)","scaleRef":"the mount's overall length, overall_length = 5.315 in, over the underside's 895.0 px (columns 52.4 to 947.4): 168.4 px/in in the underside's plane; the rings, an inch and a half further from the lens, by the cap screws' spacing (0.489 in over 78.7 px: 160.9 px/in)","method":"the pocket's rear end, column 568 on a gridded enlargement, from the rear bolt's bar (831.5)","via":"harvest"}}]},"under_pocket_mid_x1":{"label":"Underside pocket (between the front cross bolt and the lug), its front end ahead of the rear cross bolt","kind":"length","measurements":[{"id":"underside","value":2.17,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount c306082280c1 (Reptilia, ...CLEAR-ALONE-BOTTOMFOR-SITE.jpg: the clear mount straight from below, 1000 x 1000)","scaleRef":"the mount's overall length, overall_length = 5.315 in, over the underside's 895.0 px (columns 52.4 to 947.4): 168.4 px/in in the underside's plane; the rings, an inch and a half further from the lens, by the cap screws' spacing (0.489 in over 78.7 px: 160.9 px/in)","method":"the pocket's front end, column 466 on a gridded enlargement, from the rear bolt's bar (831.5)","via":"harvest"}}]},"under_pocket_rear_x0":{"label":"Underside pocket (between the lug and the rear cross bolt), its rear end ahead of the rear cross bolt","kind":"length","measurements":[{"id":"underside","value":0.264,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount c306082280c1 (Reptilia, ...CLEAR-ALONE-BOTTOMFOR-SITE.jpg: the clear mount straight from below, 1000 x 1000)","scaleRef":"the mount's overall length, overall_length = 5.315 in, over the underside's 895.0 px (columns 52.4 to 947.4): 168.4 px/in in the underside's plane; the rings, an inch and a half further from the lens, by the cap screws' spacing (0.489 in over 78.7 px: 160.9 px/in)","method":"the pocket's rear end, column 787 on a gridded enlargement, from the rear bolt's bar (831.5)","via":"harvest"}}]},"under_pocket_rear_x1":{"label":"Underside pocket (between the lug and the rear cross bolt), its front end ahead of the rear cross bolt","kind":"length","measurements":[{"id":"underside","value":0.977,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount c306082280c1 (Reptilia, ...CLEAR-ALONE-BOTTOMFOR-SITE.jpg: the clear mount straight from below, 1000 x 1000)","scaleRef":"the mount's overall length, overall_length = 5.315 in, over the underside's 895.0 px (columns 52.4 to 947.4): 168.4 px/in in the underside's plane; the rings, an inch and a half further from the lens, by the cap screws' spacing (0.489 in over 78.7 px: 160.9 px/in)","method":"the pocket's front end, column 667 on a gridded enlargement, from the rear bolt's bar (831.5)","via":"harvest"}}]},"under_round_behind_bolt":{"label":"Underside's round pocket in the tail, its middle behind the rear cross bolt","kind":"length","measurements":[{"id":"underside","value":0.288,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount c306082280c1 (Reptilia, ...CLEAR-ALONE-BOTTOMFOR-SITE.jpg: the clear mount straight from below, 1000 x 1000)","scaleRef":"the mount's overall length, overall_length = 5.315 in, over the underside's 895.0 px (columns 52.4 to 947.4): 168.4 px/in in the underside's plane; the rings, an inch and a half further from the lens, by the cap screws' spacing (0.489 in over 78.7 px: 160.9 px/in)","method":"the round's middle, column 880, from the rear bolt's bar (831.5)","via":"harvest"}}]},"under_round_d":{"label":"Underside's round pocket in the tail, its diameter","kind":"length","measurements":[{"id":"underside","value":0.267,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount c306082280c1 (Reptilia, ...CLEAR-ALONE-BOTTOMFOR-SITE.jpg: the clear mount straight from below, 1000 x 1000)","scaleRef":"the mount's overall length, overall_length = 5.315 in, over the underside's 895.0 px (columns 52.4 to 947.4): 168.4 px/in in the underside's plane; the rings, an inch and a half further from the lens, by the cap screws' spacing (0.489 in over 78.7 px: 160.9 px/in)","method":"the round's width (columns 857 to 902): 45 px","via":"harvest"}}]},"under_pocket_depth":{"label":"Underside's pockets, their depth","kind":"length","measurements":[{"id":"assumed","value":0.12,"unit":"in","pm":0.06,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the view from below is the only one of them and shows their floors lit and their walls in shadow, not how deep they are. Hidden against a rail.","via":"harvest"}}]},"ring_split_gap":{"label":"The gap between a cap and its lower half","kind":"length","measurements":[{"id":"left","value":0.01,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 65d1a1c3c68d (Soldier Systems, the launch post's stkl3530-3.jpg: the clear mount alone, straight left side, 640 x 427)","scaleRef":"the mount's overall length, overall_length = 5.315 in (135 mm), over the silhouette's 555.67 px (its front ring's front face at column 54.81, its tail's end at 610.48, each at the 50% level): 104.55 px/in. Checked in the photo of the same mount with a scope in it (4583eabd46bb): at that scale the tube's centre stands 1.532 in (38.9 mm) above the underside between the bosses, for the maker's 39 mm","method":"the dark line across each ring's side flat is one row of the picture deep (row 166: 114 of 255 between rows of 165)","via":"harvest"}}],"note":"The installation sheet: \"Ensure that the gap between the base and each ring cap is equal, left to right.\" Drawn as a groove as deep as it is wide, not a slit through the ring."},"clamp_bolt_groove_width":{"label":"The groove each cross bolt lies in, across the underside","kind":"length","measurements":[{"id":"underside","value":0.22,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount c306082280c1 (Reptilia, ...CLEAR-ALONE-BOTTOMFOR-SITE.jpg: the clear mount straight from below, 1000 x 1000)","scaleRef":"the mount's overall length, overall_length = 5.315 in, over the underside's 895.0 px (columns 52.4 to 947.4): 168.4 px/in in the underside's plane; the rings, an inch and a half further from the lens, by the cap screws' spacing (0.489 in over 78.7 px: 160.9 px/in)","method":"each dark bar's width at the 90 level on rows 470 to 530 (405.9 to 442.9 and 811.9 to 849.2): 37.0 and 37.3 px, a glint down the middle of each","via":"harvest"}}],"note":"Wider than a rail's slot (0.206): it is the groove and its shadow, with the bolt in it, and says nothing of the bolt's own size."},"clamp_bolt_hex_depth":{"label":"Cross bolt's head, the hex socket's depth","kind":"length","measurements":[{"id":"assumed","value":0.06,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows a socket in profile. Each head's socket is a dark hexagon in the two left side views, with the slot across it.","via":"harvest"}}]},"edge_break":{"label":"The break on the mount's machined edges","kind":"length","measurements":[{"id":"assumed","value":0.006,"unit":"in","pm":0.004,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows an edge in profile at a size to read it: the 640 px side views have the mount's edges a pixel wide (0.01 in) at most.","via":"harvest"}}]},"boss_top_above_rail":{"label":"Clamp bosses' top above the rail's top (where each runs out under the plate's chamfer)","kind":"length","measurements":[{"id":"left","value":0.29,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/reptilia-aus-30mm-mount 65d1a1c3c68d (Soldier Systems, the launch post's stkl3530-3.jpg: the clear mount alone, straight left side, 640 x 427)","scaleRef":"the mount's overall length, overall_length = 5.315 in (135 mm), over the silhouette's 555.67 px (its front ring's front face at column 54.81, its tail's end at 610.48, each at the 50% level): 104.55 px/in. Checked in the photo of the same mount with a scope in it (4583eabd46bb): at that scale the tube's centre stands 1.532 in (38.9 mm) above the underside between the bosses, for the maker's 39 mm","method":"the front boss on a contrast-raised enlargement: its face runs up to row 308, under the plate's lit chamfer (rows 302 to 308); the underside is row 338.0","via":"harvest"}}],"note":"Each boss flares out along the rail above the rail's top, in a concave round at each end (columns 226 to 237 and 343 to 354 at the front one): not drawn."}}},{"subject":"reptilia-dot-mount-193","title":"Reptilia DOT MOUNT FOR AIMPOINT® MICRO – 1.93″ HEIGHT (black 100-037, flat dark earth 100-038)","dimensions":{"optical_height":{"label":"Optical axis above the rail's top, as the maker gives it (no dot named: its pictures show a CompM5)","kind":"length","measurements":[{"id":"maker","value":1.93,"unit":"in","pm":0.005,"stated":"the 1.93 DOT Mount attaches to any M1913 Picatinny rail to place the optical axis at 1.93 inches above the rail.","source":{"type":"spec","publisher":"manufacturer","name":"Reptilia, DOT MOUNT FOR AIMPOINT® MICRO - 1.93\" HEIGHT (product page)","url":"https://reptiliacorp.com/product/dot-mount-for-aimpoint-t-1-t-2-compm5-193-height/","retrieved":"2026-11-03","via":"harvest"}},{"id":"pa","value":1.93,"unit":"in","pm":0.005,"stated":"Mount Height 1.93 in.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Reptilia Corp DOT Mount for Aimpoint Micro - Black - 1.93\"","url":"https://www.primaryarms.com/reptilia-corp-dot-mount-aimpoint-micro-black-1.93in","retrieved":"2026-11-03","via":"harvest"}}],"adopt":{"from":"maker","reason":"The maker's own sentence; Primary Arms repeats the figure."},"note":"The maker's only height. The page names no dot; it is headed \"DOT Mount for Aimpoint T-1/T-2/CompM5 – 1.93″ Height\", lists twenty-odd Micro-footprint dots as compatible, and every photograph of it on the page has an Aimpoint CompM5 on it. Its article on the height: \"A 1.93-inch optic height refers to the approximate distance from the centerline of the optic to the rail of the rifle\" (https://reptiliacorp.com/understanding-1-93-inch-optic-heights/, as the discovery read it)."},"compm5_axis_above_rail":{"label":"The CompM5's axis above the rail's top in the maker's on-rifle view (a check of the view's scale against the maker's figure)","kind":"length","measurements":[{"id":"onrail","value":1.917,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/reptilia-dot-mount-193 c2a2814a9ab4 (the maker's LEFT-SIDE-MOUNTED-FOR-site.jpg: a CompM5 on the FDE mount on a receiver, square from the left, level, 1000 x 1000)","scaleRef":"the receiver's rail teeth beside the base: four tooth centres at row 772, 746.5, 817.0, 887.5 and 958.5 px, 70.67 px a slot (the standard's 0.3937 in): 179.5 px/in; the slots' floor reads 21 px (0.117 in) under the tooth tops, the standard's 0.118","method":"the front cover ring's top and bottom edges in columns 218 to 236 (dark runs 321.5 to 525 px), its middle 423.3 px; the tooth tops at 767.3 px","via":"harvest"}}],"note":"Not a figure of the mount's: the CompM5 isn't on file. The front lens cover's ring, read where its top shows under the cover's hinge (row 321.5) and at its bottom (525): its middle, the lens's axis, 1.917 in over the tooth tops (767.3). The maker's 1.93 for the dot pictured lands within 0.013 in: the rail's scale and the maker's figure agree."},"lip_top_above_rail":{"label":"The deck's lips' top (the outline's top, where a side view sees the dot's base meet the deck) above the rail's top","kind":"length","measurements":[{"id":"onrail","value":1.41,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/reptilia-dot-mount-193 c2a2814a9ab4 (the maker's LEFT-SIDE-MOUNTED-FOR-site.jpg: a CompM5 on the FDE mount on a receiver, square from the left, level, 1000 x 1000)","scaleRef":"the receiver's rail teeth beside the base: four tooth centres at row 772, 746.5, 817.0, 887.5 and 958.5 px, 70.67 px a slot (the standard's 0.3937 in): 179.5 px/in; the slots' floor reads 21 px (0.117 in) under the tooth tops, the standard's 0.118","method":"the tan deck's top edge over columns 350 to 650 (first tan pixel at 514 to 515; the CompM5's black base above it) to the tooth tops beside the base (767.3): 253 px","via":"harvest"}}],"note":"The deck has two raised lips along its long edges, and a dot's base stands between them on the floor (lip_height lower). From the side the near lip hides the base's foot: the seam a side view sees is the lip's top."},"lip_height":{"label":"The lips' height above the deck's floor","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file is square on to the deck's end. Primary Arms' view from the right and above (932ddb83c5e0) has each lip's inner wall about a quarter of the deck plate's lettered side face high.","via":"harvest"}}]},"deck_above_rail":{"label":"The deck's floor (where a dot's base sits) above the rail's top","kind":"length","measurements":[{"id":"t2","value":1.341,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.optical_height} - {aimpoint-micro-t-2.axis_above_base}","via":"harvest"},"note":"1.93 in less the T-2's 0.589 in."},{"id":"onrail","value":1.38,"unit":"in","pm":0.025,"source":{"type":"derived","expr":"{.lip_top_above_rail} - {.lip_height}","via":"harvest"},"note":"1.41 in less the lips' 0.03 in."}],"adopt":{"from":"onrail","reason":"A reading of the deck itself, on the maker's own view of this mount on a rail; the other is the maker's figure for a CompM5 worked out with a T-2's axis, which the same view puts 0.05 in too high for the dot pictured. The two agree within their ±."},"note":"Worked out two ways. From the maker's height with the T-2's axis over its base: the Micro the mount is named for, and the only Micro on file whose axis over its own base is read (the CompM5 the maker's pictures show isn't on file). And read on the maker's view of the mount on a rail, from the lips' top less their height. They agree within their ±; the reading is the deck itself and is adopted. The maker's figure is for the CompM5 it pictures, whose axis stands 1.917 − 1.38 = 0.54 in over this floor in that view: 0.05 under the T-2's 0.589 (aimpoint-micro-t-2.axis_above_base), the difference between the two measurements. Scalarworks' drawing of its 1.93 in mount with a T-2 on it (scalarworks-SW0120-diagram-A.png, filed with scalarworks-leap-01-micro-193 as c5d15b40764b: \"1.93\" OPTIC CENTER\") has the T-2's axis about 0.53 in over the mount's top, as this view has the CompM5's: the T-2's 0.589 may be high."},"deck_x":{"label":"The footprint's middle along the deck, ahead of the clamp's middle","kind":"length","measurements":[{"id":"onrail","value":0,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/reptilia-dot-mount-193 c2a2814a9ab4 (the maker's LEFT-SIDE-MOUNTED-FOR-site.jpg: a CompM5 on the FDE mount on a receiver, square from the left, level, 1000 x 1000)","scaleRef":"the receiver's rail teeth beside the base: four tooth centres at row 772, 746.5, 817.0, 887.5 and 958.5 px, 70.67 px a slot (the standard's 0.3937 in): 179.5 px/in; the slots' floor reads 21 px (0.117 in) under the tooth tops, the standard's 0.118","method":"the deck's top (columns 330 to 671 at row 518, middle 500.5) over the base's foot (317 to 682 at row 790, middle 499.5) and the cross bolt's head (middle 500): the deck stands centred over the base and its bolt within a pixel, and its four screw holes and key lie about its middle in the views from above (932ddb83c5e0, ae40bf4e074b)","via":"harvest"}}]},"mount_length":{"label":"The base's length along the rail (at its foot)","kind":"length","measurements":[{"id":"onrail","value":2.039,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/reptilia-dot-mount-193 c2a2814a9ab4 (the maker's LEFT-SIDE-MOUNTED-FOR-site.jpg: a CompM5 on the FDE mount on a receiver, square from the left, level, 1000 x 1000)","scaleRef":"the receiver's rail teeth beside the base: four tooth centres at row 772, 746.5, 817.0, 887.5 and 958.5 px, 70.67 px a slot (the standard's 0.3937 in): 179.5 px/in; the slots' floor reads 21 px (0.117 in) under the tooth tops, the standard's 0.118","method":"the base's two ends at row 790 (317 to 682, the tan silhouette against the black receiver and the white ground): 366 px","via":"harvest"}}]},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"maker","value":55,"unit":"g","stated":"55 grams","source":{"type":"spec","publisher":"manufacturer","name":"Reptilia, DOT MOUNT FOR AIMPOINT® MICRO - 1.93\" HEIGHT (product page)","url":"https://reptiliacorp.com/product/dot-mount-for-aimpoint-t-1-t-2-compm5-193-height/","retrieved":"2026-11-03","via":"harvest"}},{"id":"riflesupply","value":55,"unit":"g","stated":"Weight: 55 Grams","source":{"type":"spec","publisher":"retailer","name":"Rifle Supply, Reptilia DOT Mount | 1.93\" Height | Fits Aimpoint Micro | Black | 100-037","url":"https://riflesupply.com/Reptilia-DOT-Mount-193-Height-Fits-Aimpoint-Micro-Black-100-037_p_6467.html","retrieved":"2026-11-03","via":"harvest"}},{"id":"pa","value":1.9,"unit":"oz","stated":"Weight: 1.9 ounces","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Reptilia Corp DOT Mount for Aimpoint Micro - Black - 1.93\"","url":"https://www.primaryarms.com/reptilia-corp-dot-mount-aimpoint-micro-black-1.93in","retrieved":"2026-11-03","via":"harvest"}}],"adopt":{"from":"maker","reason":"The maker's own figure; Rifle Supply repeats it and Primary Arms' 1.9 oz (54 g) is it rounded."}},"clamp_below_rail":{"label":"The base's foot below the rail's top","kind":"length","measurements":[{"id":"side","value":0.223,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/reptilia-dot-mount-193 e9d8dbdb0275 (Rifle Supply 125332.png: the black 1.93 alone, square from the left, transparent ground, 1280 x 853)","scaleRef":"the base's length, mount_length = 2.039 in over its 627 px: 307.5 px/in","method":"the traced outline's foot 1.633 in under its top (the lips' top), less lip_top_above_rail (1.41 in, the maker's on-rifle view); on that view the foot is in the base's shadow against the black receiver, and the lit rim under the bolt's head reaches 806 px, 0.21 in under the tooth tops","via":"harvest"}}]},"deck_plate_thickness":{"label":"The deck plate's side face, from the lips' top down to where its underside turns into the stem","kind":"length","measurements":[{"id":"side","value":0.132,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/reptilia-dot-mount-193 e9d8dbdb0275 (Rifle Supply 125332.png: the black 1.93 alone, square from the left, transparent ground, 1280 x 853)","scaleRef":"mount_length over the outline's 627 px: 307.5 px/in","method":"the lettered band down the deck's side, rows 197.5 to 238 (40.5 px); the outline's ends turn at 0.13 and 0.133 under its top","via":"harvest"}}]},"base_end_height":{"label":"The base's square ends, from its foot to where its top turns up into the stem","kind":"length","measurements":[{"id":"side","value":0.368,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/reptilia-dot-mount-193 e9d8dbdb0275 (Rifle Supply 125332.png: the black 1.93 alone, square from the left, transparent ground, 1280 x 853)","scaleRef":"mount_length over the outline's 627 px: 307.5 px/in","method":"the traced outline's ends: the corner at 1.265 in under its top at both ends, its foot at 1.633","via":"harvest"}}]},"flange_thickness":{"label":"Each I-beam flange's thickness along the rail (from the waist's silhouette in to the web's face)","kind":"length","measurements":[{"id":"side","value":0.2,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/reptilia-dot-mount-193 e9d8dbdb0275 (Rifle Supply 125332.png: the black 1.93 alone, square from the left, transparent ground, 1280 x 853)","scaleRef":"mount_length over the outline's 627 px: 307.5 px/in","method":"the waist's silhouette (455 and 773 px at row 400) to the lit inner edge of each flange, where the web's face begins (about 520 and 712 px): 65 and 61 px","via":"harvest"}}]},"web_thickness":{"label":"The I-beam's web across the rifle, between its two flanges","kind":"length","measurements":[{"id":"assumed","value":0.1,"unit":"in","pm":0.08,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: inside what the maker's two weights leave for the web (the note), where the views from the right and front show the web's face well inside the flange's (be5535ecdde1, 932ddb83c5e0).","via":"harvest"}}],"note":"No view on file is square on to the mount's end, and no page gives it. The maker's two weights bound it: the 1.93 (55 g) and the lower 1/3 (51 g) differ by 4 g (± 1 g, each to its gram), 0.087 in³ of 7075 (std.density.aluminium_7075), over the 0.33 in their stems' heights differ by (1.133 and 0.805 in between the deck plate and the base, by their outlines and readings): 0.265 ± 0.07 in² of metal in a stem's section at its waist. The two flanges, flange_thickness along the rail by the stem's width across, are 0.22 of that, which leaves the web between them (about 0.62 in long) 0.07 ± 0.11 in thick. Drawn at 0.1."},"width":{"label":"Width across the rifle (the deck and the base)","kind":"length","measurements":[{"id":"sibling","value":1.24,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{reptilia-dot-mount-39mm.width}","via":"harvest"},"note":"31.5 mm, the lower 1/3's (the reader's \"Width- 31.5mm\")."}],"note":"No view or page gives this height's width: the lower 1/3's, as a reader measured it, the only width on file. The two heights' decks and bases read the same lengths and depths in their side views (mount_length, deck_plate_thickness, base_end_height), and the maker's three-quarter views of the two look alike across."},"stem_width":{"label":"The I-beam across the rifle at its narrowest (its two flanges, the outside a caliper reaches)","kind":"length","measurements":[{"id":"sibling","value":0.551,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{reptilia-dot-mount-39mm.stem_width}","via":"harvest"},"note":"14 mm, the lower 1/3's."}],"note":"No view or page gives it for this height: the lower 1/3's, as a reader measured it, the only figure on file."},"bolt_above_foot":{"label":"The cross bolt's axis above the base's foot","kind":"length","measurements":[{"id":"side","value":0.226,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/reptilia-dot-mount-193 e9d8dbdb0275 (Rifle Supply 125332.png: the black 1.93 alone, square from the left, transparent ground, 1280 x 853)","scaleRef":"mount_length over the outline's 627 px: 307.5 px/in","method":"the round seat's middle (612, 628 px) over the foot (697.5)","via":"harvest"}}]},"bolt_seat_d":{"label":"The round seat the cross bolt's head lies flush in (on the left face)","kind":"length","measurements":[{"id":"side","value":0.403,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/reptilia-dot-mount-193 e9d8dbdb0275 (Rifle Supply 125332.png: the black 1.93 alone, square from the left, transparent ground, 1280 x 853)","scaleRef":"mount_length over the outline's 627 px: 307.5 px/in","method":"the seat's lit outer rim, 550 to 674 px across at row 628","via":"harvest"}}]},"bolt_head_d":{"label":"The cross bolt's head","kind":"length","measurements":[{"id":"side","value":0.306,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/reptilia-dot-mount-193 e9d8dbdb0275 (Rifle Supply 125332.png: the black 1.93 alone, square from the left, transparent ground, 1280 x 853)","scaleRef":"mount_length over the outline's 627 px: 307.5 px/in","method":"the head's dark disc inside the seat, about 94 px across","via":"harvest"}}]},"bolt_seat_depth":{"label":"How far the seat's floor (the head's face) lies inside the base's left face","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the maker says the clamp and bolt \"sit flush with the body of the mount\"; the views show a lit rim round the head, which is drawn as a seat this deep.","via":"harvest"}}]},"bolt_slot_width":{"label":"The slot across the bolt's head","kind":"length","measurements":[{"id":"assumed","value":0.045,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the slot shows across the head in every left view, about a seventh of the head's width; no view gives its depth (drawn as deep as it is wide).","via":"harvest"}}]},"clamp_length":{"label":"The steel clamp's length along the rail (on the right face)","kind":"length","measurements":[{"id":"assumed","value":0.6,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view is square on to the right face. In the views from the right and above (932ddb83c5e0, ae40bf4e074b) the clamp's faceted body is about three tenths of the base's length.","via":"harvest"}}]},"clamp_top_above_foot":{"label":"The steel clamp's top above the base's foot","kind":"length","measurements":[{"id":"assumed","value":0.33,"unit":"in","pm":0.06,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: in the views from the right the clamp's body reaches nearly to the base's top edge, a little under base_end_height.","via":"harvest"}}]},"clamp_proud":{"label":"How far the steel clamp stands out of the base's right face","kind":"length","measurements":[{"id":"assumed","value":0.05,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the maker says it sits \"flush with the body\"; the views from the right show its faceted face standing a little proud.","via":"harvest"}}]},"bolt_end_d":{"label":"The cross bolt's end, where it stands out of the steel clamp","kind":"length","measurements":[{"id":"assumed","value":0.16,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: a round end in the clamp's middle in the views from the right, about half the head's width.","via":"harvest"}}]},"base_hole_d":{"label":"The four through holes in the base's top, either side of the stem","kind":"length","measurements":[{"id":"assumed","value":0.12,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: four round holes through the base's top, two either side of the stem, show in the views from above and come out in the channel's roof (125330_A of the lower 1/3, the same base); about a twentieth of the base's length across.","via":"harvest"}}]},"base_hole_x":{"label":"The base's holes ahead of and behind the clamp's middle","kind":"length","measurements":[{"id":"assumed","value":0.78,"unit":"in","pm":0.08,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: near the base's ends, outside the flare into the stem, in the views from above (ae40bf4e074b).","via":"harvest"}}]},"base_hole_z":{"label":"The base's holes out from the middle across the rifle","kind":"length","measurements":[{"id":"assumed","value":0.4,"unit":"in","pm":0.06,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: between the flanges and the base's edges in the views from above (ae40bf4e074b), and over the rail's head's edges in the view from below (125330_A).","via":"harvest"}}]},"deck_screw_d":{"label":"The four holes for the dot's screws through the deck plate","kind":"length","measurements":[{"id":"assumed","value":0.17,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: four round holes inside the lips in the views from above (932ddb83c5e0), about a twelfth of the deck's length across.","via":"harvest"}}]},"deck_screw_x":{"label":"The deck's screw holes ahead of and behind the footprint's middle","kind":"length","measurements":[{"id":"assumed","value":0.62,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: in Primary Arms' three-quarter view from above (932ddb83c5e0) the two pairs are about 0.63 of the deck's length apart, a ratio read along an oblique edge.","via":"harvest"}}]},"deck_screw_z":{"label":"The deck's screw holes out from the middle across the rifle","kind":"length","measurements":[{"id":"assumed","value":0.31,"unit":"in","pm":0.06,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: in the same view the two holes of a pair are about half the deck's width apart.","via":"harvest"}}]},"edge_break":{"label":"The machined edges' break","kind":"length","measurements":[{"id":"assumed","value":0.006,"unit":"in","pm":0.004,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: every edge in the photographs is broken a little; no view resolves by how much.","via":"harvest"}}]},"base_chamfer":{"label":"The chamfer along the base's two lower outer edges (the jaws' feet)","kind":"length","measurements":[{"id":"assumed","value":0.05,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: Rifle Supply's view of the lower 1/3 from below (references/reptilia-dot-mount-39mm 019eb4af187a) has a lit strip along the near jaw's lower outer edge, about a fortieth of the base's length across (0.04 to 0.05 in); no view is square on to the base's end. The same base in both heights' side views.","via":"harvest"}}]}}},{"subject":"reptilia-dot-mount-39mm","title":"Reptilia DOT MOUNT FOR AIMPOINT® MICRO – LOWER 1/3 (39MM HEIGHT) (black 100-004, flat dark earth 100-024)","dimensions":{"optical_height":{"label":"Height as the maker names it (\"39MM HEIGHT\", lower 1/3 co-witness; no dot named: its pictures show a Micro T-2)","kind":"length","measurements":[{"id":"maker","value":39,"unit":"mm","pm":0.5,"stated":"DOT MOUNT FOR AIMPOINT® MICRO - LOWER 1/3 (39MM HEIGHT)","source":{"type":"spec","publisher":"manufacturer","name":"Reptilia, DOT MOUNT FOR AIMPOINT® MICRO - LOWER 1/3 (39MM HEIGHT) (product page)","url":"https://reptiliacorp.com/product/dot-mount-for-aimpoint-micro/","retrieved":"2026-11-03","via":"harvest"}},{"id":"rc","value":1.54,"unit":"in","stated":"39mm (1.54\") lower 1/3","source":{"type":"spec","publisher":"review","name":"RifleConfigurator, Reptilia DOT Mount (a catalog entry; its source unsaid)","url":"https://www.rifleconfigurator.com/catalog/mounts/reptilia-dot-mount","retrieved":"2026-11-03","via":"harvest"}},{"id":"pa","value":1.5,"unit":"in","pm":0.05,"stated":"This model places the center of your optic at a 1.5” height for a lower 1/3rd co-witness with AR-15 iron sights.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Reptilia Corp DOT Mount for Aimpoint Micro - Flat Dark Earth - Lower 1/3rd","url":"https://www.primaryarms.com/Reptilia-corp-dot-mount-aimpoint-micro-fde-lower-1-3rd","retrieved":"2026-11-03","via":"harvest"}}],"adopt":{"from":"maker","reason":"The maker's own figure; RifleConfigurator gives it in inches, and Primary Arms' 1.5 in is it rounded to a tenth."},"note":"The maker's title is the only figure, with no sentence saying what it is measured to or for which dot; its text: \"attaches to any M1913 Picatinny rail, and offers lower 1/3 co-witness with standard AR15-style back-up sights.\" Every photograph of it on the page has a Micro T-2 on it. Taken as the axis over the rail's top, as Aimpoint names its own 39 mm spacer (aimpoint-micro-t-2.optical_axis_above_rail). Sellers: Primary Arms \"This model places the center of your optic at a 1.5” height for a lower 1/3rd co-witness with AR-15 iron sights.\"; RifleConfigurator \"39mm (1.54\") lower 1/3\"."},"lip_top_above_rail":{"label":"The deck's lips' top (the outline's top, where a side view sees the dot's base meet the deck) above the rail's top","kind":"length","measurements":[{"id":"rifle","value":1.096,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/reptilia-dot-mount-39mm caf8996345bb (the maker's DOT-MOUNT-08.jpg: a whole carbine square from the left, the FDE lower 1/3 and a T-2 on its receiver, 1000 x 1000)","scaleRef":"the handguard's top rail: 23 tooth centres along row 446, 192 to 437 px, 11.14 px a slot (the standard's 0.3937 in): 28.29 px/in","method":"the deck's top edge (the T-2's black base over it) at half level over columns 522 to 562, row 415.4 (415.3 to 415.6); the receiver's tooth tops right of the mount, columns 578 to 626, row 446.4 (446.3 to 446.6): 31.0 px. Each edge to half a pixel","via":"harvest"}}],"note":"The deck has two raised lips along its long edges, and a dot's base stands between them on the floor (lip_height lower). From the side the near lip hides the base's foot: the seam a side view sees is the lip's top."},"lip_height":{"label":"The lips' height above the deck's floor","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file is square on to the deck's end. Primary Arms' view of the FDE from the right and above (7e3e918aa753) has each lip's inner wall about a quarter of the deck plate's lettered side face high.","via":"harvest"}}]},"deck_above_rail":{"label":"The deck's floor (where a dot's base sits) above the rail's top","kind":"length","measurements":[{"id":"t2","value":0.946,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.optical_height} - {aimpoint-micro-t-2.axis_above_base}","via":"harvest"},"note":"39 mm (1.535 in) less the T-2's 0.589 in."},{"id":"rifle","value":1.066,"unit":"in","pm":0.035,"source":{"type":"derived","expr":"{.lip_top_above_rail} - {.lip_height}","via":"harvest"},"note":"1.096 in less the lips' 0.03 in."}],"adopt":{"from":"rifle","reason":"A reading of the deck itself on the maker's own photograph of this mount on a rail, which three views agree with; the derived figure rests on reading a title's \"39MM\" as a T-2's axis over the rail's top, which none of the maker's photographs bears out. The conflict is kept: the maker's figure is 0.12 in under what its pictures show."},"note":"Worked out two ways, which DISAGREE. From the maker's 39 mm with the T-2's axis over its base (the dot every one of its photographs shows, and the Micro the mount is named for): 0.946 in. And read on the maker's square view of a carbine with this mount and a T-2 on its receiver, at the rail's pitch, from the lips' top less their height: 1.066 in. Two other views say the same as the reading: Rifle Supply's square view of the mount alone, at the reader's base length, has the lips 1.308 in over the base's foot, which would leave the base hanging 0.36 in under the rail's top on the derived figure and 0.21 on the reading (the 1.93's base, on its own rail-scaled view, hangs 0.22); and Rifle Supply's three-quarter view with a T-2 on it has the T-2's axis 0.6 in over the deck by the T-2's own height and the deck over an inch above the rail. A T-2 on the deck as read stands with its axis at 1.655 in (42 mm) by the T-2's ledger, or about 1.60 in (40.6 mm) if a Micro's axis is 0.54 in over its base as the 1.93's photograph and Scalarworks' drawing have it. What the maker's 39 mm is measured to, it doesn't say."},"deck_x":{"label":"The footprint's middle along the deck, ahead of the clamp's middle","kind":"length","measurements":[{"id":"side","value":0,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/reptilia-dot-mount-39mm 25b8fb31a520 (Rifle Supply 125330.png: the black lower 1/3 alone, square from the left, transparent ground, 1280 x 853)","scaleRef":"the base's length, mount_length = 2.055 in over its 679.7 px (columns 282 to 961.7): 330.7 px/in","method":"the deck's top (columns 286 to 941 at row 251, middle 613.4) over the base's foot (282.0 to 958.7 at row 655, middle 620.4) and the cross bolt's head (middle about 616): the deck stands over the base's middle to 7 px (0.02 in), and its four screw holes and key lie about its middle in the views from above (7e3e918aa753, 80d4a05aebb1)","via":"harvest"}}]},"mount_length":{"label":"The base's length along the rail (at its foot)","kind":"length","measurements":[{"id":"reader","value":52.2,"unit":"mm","pm":0.1,"stated":"Bottom- 52.2mm long","source":{"type":"spec","publisher":"review","name":"Soldier Systems Daily, Reptilia launches DOT Mount for Aimpoint T-1/T-2 (2019-02-12): a reader's comment (Stickman, 2019-02-14) comparing it with Geissele's T1/2 mount: \"Reptilia T1/2 mount: Weight- 49 grams (lower 1/3rd witness mount which is larger) Bottom- 52.2mm long Top- 50mm long Width- 31.5mm I Beam at most narrow point 14mm\"","url":"https://soldiersystems.net/2019/02/12/reptilia-launches-dot-mount-for-aimpoint-t-1t-2/","retrieved":"2026-11-03","via":"harvest"}},{"id":"rifle","value":2.03,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/reptilia-dot-mount-39mm caf8996345bb (the maker's DOT-MOUNT-08.jpg: a whole carbine square from the left, the FDE lower 1/3 and a T-2 on its receiver, 1000 x 1000)","scaleRef":"the handguard's top rail: 23 tooth centres along row 446, 192 to 437 px, 11.14 px a slot (the standard's 0.3937 in): 28.29 px/in","method":"the tan base's two ends at row 445 to 446, just above the receiver's tooth tops (514.0 to 571.3 px at half level; below that row it runs into the tan handguard): 57.4 px","via":"harvest"}}],"adopt":{"from":"reader","reason":"A measurement of the mount in hand, to a tenth of a millimetre; the maker's rail-scaled photograph reads it within its pixel."}},"deck_length":{"label":"The deck's length at its top","kind":"length","measurements":[{"id":"reader","value":50,"unit":"mm","pm":0.5,"stated":"Top- 50mm long","source":{"type":"spec","publisher":"review","name":"Soldier Systems Daily, Reptilia launches DOT Mount for Aimpoint T-1/T-2 (2019-02-12): a reader's comment (Stickman, 2019-02-14) comparing it with Geissele's T1/2 mount: \"Reptilia T1/2 mount: Weight- 49 grams (lower 1/3rd witness mount which is larger) Bottom- 52.2mm long Top- 50mm long Width- 31.5mm I Beam at most narrow point 14mm\"","url":"https://soldiersystems.net/2019/02/12/reptilia-launches-dot-mount-for-aimpoint-t-1t-2/","retrieved":"2026-11-03","via":"harvest"}},{"id":"rifle","value":1.89,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/reptilia-dot-mount-39mm caf8996345bb (the maker's DOT-MOUNT-08.jpg: a whole carbine square from the left, the FDE lower 1/3 and a T-2 on its receiver, 1000 x 1000)","scaleRef":"the handguard's top rail: 23 tooth centres along row 446, 192 to 437 px, 11.14 px a slot (the standard's 0.3937 in): 28.29 px/in","method":"the tan deck's ends at rows 416 to 417 (515.2 to 568.7 px at half level): 53.5 px","via":"harvest"}}],"adopt":{"from":"reader","reason":"A measurement of the mount in hand; the square view of the mount alone has the deck at the same share of the base's length as the reader's two figures."},"note":"Rifle Supply's square view has the deck's top 0.965 of the base's foot (654.9 of 678.7 px), and so has the 1.93's (605.0 of 626.4): 1.983 in at the reader's base length. The maker's whole-rifle view reads it 1.89, a pixel and a half short at 28 px an inch."},"width":{"label":"Width across the rifle (the deck and the base)","kind":"length","measurements":[{"id":"reader","value":31.5,"unit":"mm","pm":0.1,"stated":"Width- 31.5mm","source":{"type":"spec","publisher":"review","name":"Soldier Systems Daily, Reptilia launches DOT Mount for Aimpoint T-1/T-2 (2019-02-12): a reader's comment (Stickman, 2019-02-14) comparing it with Geissele's T1/2 mount: \"Reptilia T1/2 mount: Weight- 49 grams (lower 1/3rd witness mount which is larger) Bottom- 52.2mm long Top- 50mm long Width- 31.5mm I Beam at most narrow point 14mm\"","url":"https://soldiersystems.net/2019/02/12/reptilia-launches-dot-mount-for-aimpoint-t-1t-2/","retrieved":"2026-11-03","via":"harvest"}}],"note":"The reader's \"Width\", taken to be the mount's across the rifle at its widest, the deck plate and the base, which the views from above and the front have about equal."},"stem_width":{"label":"The I-beam across the rifle at its narrowest (its two flanges, the outside a caliper reaches)","kind":"length","measurements":[{"id":"reader","value":14,"unit":"mm","pm":0.5,"stated":"I Beam at most narrow point 14mm","source":{"type":"spec","publisher":"review","name":"Soldier Systems Daily, Reptilia launches DOT Mount for Aimpoint T-1/T-2 (2019-02-12): a reader's comment (Stickman, 2019-02-14) comparing it with Geissele's T1/2 mount: \"Reptilia T1/2 mount: Weight- 49 grams (lower 1/3rd witness mount which is larger) Bottom- 52.2mm long Top- 50mm long Width- 31.5mm I Beam at most narrow point 14mm\"","url":"https://soldiersystems.net/2019/02/12/reptilia-launches-dot-mount-for-aimpoint-t-1t-2/","retrieved":"2026-11-03","via":"harvest"}}],"note":"The reader's \"I Beam at most narrow point\", taken to be the I-beam's outside across the rifle at its waist, which a caliper reaches at its two flanges: the web between them is set well inside them in the views from the right and front (web_thickness)."},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"maker","value":51,"unit":"g","stated":"51 grams","source":{"type":"spec","publisher":"manufacturer","name":"Reptilia, DOT MOUNT FOR AIMPOINT® MICRO - LOWER 1/3 (39MM HEIGHT) (product page)","url":"https://reptiliacorp.com/product/dot-mount-for-aimpoint-micro/","retrieved":"2026-11-03","via":"harvest"}},{"id":"riflesupply","value":51,"unit":"g","stated":"Weight: 51 Grams","source":{"type":"spec","publisher":"retailer","name":"Rifle Supply, Reptilia DOT Mount | Fits Aimpoint Micro | Black | 100-004","url":"https://riflesupply.com/Reptilia-DOT-Mount-Fits-Aimpoint-Micro-Black-100-004_p_6465.html","retrieved":"2026-11-03","via":"harvest"}},{"id":"pa","value":1.8,"unit":"oz","stated":"Weight: 1.8 ounces","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Reptilia Corp DOT Mount for Aimpoint Micro - Flat Dark Earth - Lower 1/3rd","url":"https://www.primaryarms.com/Reptilia-corp-dot-mount-aimpoint-micro-fde-lower-1-3rd","retrieved":"2026-11-03","via":"harvest"}},{"id":"reader","value":49,"unit":"g","stated":"Weight- 49 grams (lower 1/3rd witness mount which is larger)","source":{"type":"spec","publisher":"review","name":"Soldier Systems Daily, Reptilia launches DOT Mount for Aimpoint T-1/T-2 (2019-02-12): a reader's comment (Stickman, 2019-02-14) comparing it with Geissele's T1/2 mount: \"Reptilia T1/2 mount: Weight- 49 grams (lower 1/3rd witness mount which is larger) Bottom- 52.2mm long Top- 50mm long Width- 31.5mm I Beam at most narrow point 14mm\"","url":"https://soldiersystems.net/2019/02/12/reptilia-launches-dot-mount-for-aimpoint-t-1t-2/","retrieved":"2026-11-03","via":"harvest"}}],"adopt":{"from":"maker","reason":"The maker's own figure; Rifle Supply repeats it and Primary Arms' 1.8 oz (51 g) is it. The reader's 49 g, on his own scale, is 4% under."}},"clamp_below_rail":{"label":"The base's foot below the rail's top","kind":"length","measurements":[{"id":"side","value":0.209,"unit":"in","pm":0.035,"source":{"type":"photo","photo":"references/reptilia-dot-mount-39mm 25b8fb31a520 (Rifle Supply 125330.png: the black lower 1/3 alone, square from the left, transparent ground, 1280 x 853)","scaleRef":"the base's length, mount_length = 2.055 in over its 679.7 px: 330.7 px/in","method":"the traced outline's foot 1.305 in under its top (the lips' top), less lip_top_above_rail (1.096 in, the maker's whole-rifle view); the 1.93's base, on its own rail-scaled view, hangs 0.22","via":"harvest"}}]},"deck_plate_thickness":{"label":"The deck plate's side face, from the lips' top down to where its underside turns into the stem","kind":"length","measurements":[{"id":"side","value":0.13,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/reptilia-dot-mount-39mm 25b8fb31a520 (Rifle Supply 125330.png: the black lower 1/3 alone, square from the left, transparent ground, 1280 x 853)","scaleRef":"mount_length over the outline's 679.7 px: 330.7 px/in","method":"the lettered band down the deck's side, rows 247.5 to about 290 (42.5 px); the outline's ends turn at 0.131 under its top","via":"harvest"}}]},"base_end_height":{"label":"The base's square ends, from its foot to where its top turns up into the stem","kind":"length","measurements":[{"id":"side","value":0.37,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/reptilia-dot-mount-39mm 25b8fb31a520 (Rifle Supply 125330.png: the black lower 1/3 alone, square from the left, transparent ground, 1280 x 853)","scaleRef":"mount_length over the outline's 679.7 px: 330.7 px/in","method":"the traced outline's ends: the corners at 0.93 (front) and 0.925 to 0.948 (rear) in under its top, its foot at 1.305","via":"harvest"}}]},"flange_thickness":{"label":"Each I-beam flange's thickness along the rail (from the waist's silhouette in to the web's face)","kind":"length","measurements":[{"id":"side","value":0.2,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/reptilia-dot-mount-39mm 25b8fb31a520 (Rifle Supply 125330.png: the black lower 1/3 alone, square from the left, transparent ground, 1280 x 853)","scaleRef":"mount_length over the outline's 679.7 px: 330.7 px/in","method":"the waist's silhouette (about 437 px at row 420) to the lit inner edge of the flange where the web's face begins (about 503 px): 66 px; the other side 56 px","via":"harvest"}}]},"web_thickness":{"label":"The I-beam's web across the rifle, between its two flanges","kind":"length","measurements":[{"id":"assumed","value":0.1,"unit":"in","pm":0.08,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: inside what the maker's two weights leave for the web (the note), where the views from the right and front show the web's face well inside the flange's (be5535ecdde1, 932ddb83c5e0).","via":"harvest"}}],"note":"No view on file is square on to the mount's end, and no page gives it. The maker's two weights bound it: the 1.93 (55 g) and the lower 1/3 (51 g) differ by 4 g (± 1 g, each to its gram), 0.087 in³ of 7075 (std.density.aluminium_7075), over the 0.33 in their stems' heights differ by (1.133 and 0.805 in between the deck plate and the base, by their outlines and readings): 0.265 ± 0.07 in² of metal in a stem's section at its waist. The two flanges, flange_thickness along the rail by the stem's width across, are 0.22 of that, which leaves the web between them (about 0.62 in long) 0.07 ± 0.11 in thick. Drawn at 0.1."},"bolt_above_foot":{"label":"The cross bolt's axis above the base's foot","kind":"length","measurements":[{"id":"side","value":0.23,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/reptilia-dot-mount-39mm 25b8fb31a520 (Rifle Supply 125330.png: the black lower 1/3 alone, square from the left, transparent ground, 1280 x 853)","scaleRef":"mount_length over the outline's 679.7 px: 330.7 px/in","method":"the round seat's middle (616, 603 px) over the foot (679)","via":"harvest"}}]},"bolt_seat_d":{"label":"The round seat the cross bolt's head lies flush in (on the left face)","kind":"length","measurements":[{"id":"side","value":0.381,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/reptilia-dot-mount-39mm 25b8fb31a520 (Rifle Supply 125330.png: the black lower 1/3 alone, square from the left, transparent ground, 1280 x 853)","scaleRef":"mount_length over the outline's 679.7 px: 330.7 px/in","method":"the seat's lit outer rim, about 126 px across at row 603","via":"harvest"}}]},"bolt_head_d":{"label":"The cross bolt's head","kind":"length","measurements":[{"id":"side","value":0.3,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/reptilia-dot-mount-39mm 25b8fb31a520 (Rifle Supply 125330.png: the black lower 1/3 alone, square from the left, transparent ground, 1280 x 853)","scaleRef":"mount_length over the outline's 679.7 px: 330.7 px/in","method":"the head's dark disc inside the seat, about 100 px across","via":"harvest"}}]},"bolt_seat_depth":{"label":"How far the seat's floor (the head's face) lies inside the base's left face","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the maker says the clamp and bolt \"sit flush with the body of the mount\"; the views show a lit rim round the head, which is drawn as a seat this deep.","via":"harvest"}}]},"bolt_slot_width":{"label":"The slot across the bolt's head","kind":"length","measurements":[{"id":"assumed","value":0.045,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the slot shows across the head in every left view, about a seventh of the head's width; no view gives its depth (drawn as deep as it is wide).","via":"harvest"}}]},"clamp_length":{"label":"The steel clamp's length along the rail (on the right face)","kind":"length","measurements":[{"id":"assumed","value":0.6,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view is square on to the right face. In the views from the right and above (7e3e918aa753, the maker's DOT-MOUNT-03) the clamp's faceted body is about three tenths of the base's length.","via":"harvest"}}]},"clamp_top_above_foot":{"label":"The steel clamp's top above the base's foot","kind":"length","measurements":[{"id":"assumed","value":0.33,"unit":"in","pm":0.06,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: in the views from the right the clamp's body reaches nearly to the base's top edge, a little under base_end_height.","via":"harvest"}}]},"clamp_proud":{"label":"How far the steel clamp stands out of the base's right face","kind":"length","measurements":[{"id":"assumed","value":0.05,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the maker says it sits \"flush with the body\"; the views from the right show its faceted face standing a little proud.","via":"harvest"}}]},"bolt_end_d":{"label":"The cross bolt's end, where it stands out of the steel clamp","kind":"length","measurements":[{"id":"assumed","value":0.16,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: a round end in the clamp's middle in the views from the right and from below (019eb4af187a), about half the head's width.","via":"harvest"}}]},"base_hole_d":{"label":"The four through holes in the base's top, either side of the stem","kind":"length","measurements":[{"id":"assumed","value":0.12,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: four round holes through the base, two either side of the stem, show in the views from above and come out in the channel's roof (019eb4af187a); about a twentieth of the base's length across.","via":"harvest"}}]},"base_hole_x":{"label":"The base's holes ahead of and behind the clamp's middle","kind":"length","measurements":[{"id":"assumed","value":0.78,"unit":"in","pm":0.08,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: near the base's ends, outside the flare into the stem, in the views from above and below (7e3e918aa753, 019eb4af187a).","via":"harvest"}}]},"base_hole_z":{"label":"The base's holes out from the middle across the rifle","kind":"length","measurements":[{"id":"assumed","value":0.4,"unit":"in","pm":0.06,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: between the flanges and the base's edges in the views from above, and over the rail's head's edges in the view from below (019eb4af187a).","via":"harvest"}}]},"deck_screw_d":{"label":"The four holes for the dot's screws through the deck plate","kind":"length","measurements":[{"id":"assumed","value":0.17,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: four round holes inside the lips in the views from above (80d4a05aebb1, 7e3e918aa753), about a twelfth of the deck's length across.","via":"harvest"}}]},"deck_screw_x":{"label":"The deck's screw holes ahead of and behind the footprint's middle","kind":"length","measurements":[{"id":"assumed","value":0.62,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: in Primary Arms' three-quarter view from above (7e3e918aa753) the two pairs are about 0.63 of the deck's length apart, a ratio read along an oblique edge.","via":"harvest"}}]},"deck_screw_z":{"label":"The deck's screw holes out from the middle across the rifle","kind":"length","measurements":[{"id":"assumed","value":0.31,"unit":"in","pm":0.06,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: in the same view the two holes of a pair are about half the deck's width apart.","via":"harvest"}}]},"edge_break":{"label":"The machined edges' break","kind":"length","measurements":[{"id":"assumed","value":0.006,"unit":"in","pm":0.004,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: every edge in the photographs is broken a little; no view resolves by how much.","via":"harvest"}}]},"base_chamfer":{"label":"The chamfer along the base's two lower outer edges (the jaws' feet)","kind":"length","measurements":[{"id":"assumed","value":0.05,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: Rifle Supply's view of the lower 1/3 from below (references/reptilia-dot-mount-39mm 019eb4af187a) has a lit strip along the near jaw's lower outer edge, about a fortieth of the base's length across (0.04 to 0.05 in); no view is square on to the base's end. The same base in both heights' side views.","via":"harvest"}}]}}},{"subject":"rise-lpk","title":"Rise Armament lower parts kit, less trigger","dimensions":{"takedown_pin_head_d":{"label":"Takedown pin head diameter","kind":"length","measurements":[{"id":"tdp","value":0.375,"unit":"in","stated":".375 DIA (end view)","source":{"type":"standard","doc":"US Army TDP drawing 8448584 (Pin, Takedown), sheet 1 of 1; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p103","via":"user"}}]},"takedown_pin_head_t":{"label":"Takedown pin head thickness (domed face to the face that seats on the receiver)","kind":"length","measurements":[{"id":"tdp","value":0.09,"unit":"in","pm":0.005,"stated":".09","source":{"type":"standard","doc":"US Army TDP drawing 8448584 (Pin, Takedown), sheet 1 of 1; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p103","via":"user"},"note":"From the dome's crown to the head's inner face; a .035 relief follows it, inside the receiver."}]},"pivot_pin_head_d":{"label":"Pivot pin head diameter","kind":"length","measurements":[{"id":"tdp","value":0.4,"unit":"in","pm":0.005,"stated":".400 DIA -.005 (end view)","source":{"type":"standard","doc":"US Army TDP drawing 8448621 (Pin, Receiver Pivot), sheet 1 of 1; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p102","via":"user"},"note":"The head has a flat .1355 ± .0025 from the axis (end view); its orientation in the receiver isn't drawn."}]},"pivot_pin_head_flat":{"label":"Pivot pin head, its flat from the pin's axis","kind":"length","measurements":[{"id":"tdp","value":0.1355,"unit":"in","pm":0.0025,"stated":".1355 ± .0025 from the axis (end view)","source":{"type":"standard","doc":"US Army TDP drawing 8448621 (Pin, Receiver Pivot), sheet 1 of 1; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p102","via":"user"}}],"note":"Which way the flat is turned in the receiver isn't drawn. It is drawn turned to the rear: a forged lower's roll along the top of its magazine well ends square 0.144 in behind the pin's axis (bad-workhorse-lower.well_roll_front_x, bca-stripped-lower's the same), and a round head would stand in that end."},"pivot_pin_head_t":{"label":"Pivot pin head thickness (domed face to the face that seats on the receiver)","kind":"length","measurements":[{"id":"tdp","value":0.18,"unit":"in","pm":0.005,"stated":".18 (top chain: 1.312 REF = .18 + 1.132)","source":{"type":"standard","doc":"US Army TDP drawing 8448621 (Pin, Receiver Pivot), sheet 1 of 1; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p102","via":"user"}}]},"pin_head_dome_r":{"label":"Takedown and pivot pin heads, spherical radius of the domed face","kind":"length","measurements":[{"id":"tdp","value":0.38,"unit":"in","pm":0.005,"stated":".38 SPHERICAL RADIUS (both drawings)","source":{"type":"standard","doc":"US Army TDP drawing 8448584 (Pin, Takedown), sheet 1 of 1; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p103; and 8448621 (.38 SPHERICAL R)","via":"user"}}]},"selector_hub_d":{"label":"Selector lever hub diameter (face view)","kind":"length","measurements":[{"id":"tdp","value":0.48,"unit":"in","pm":0.005,"stated":".48 DIA","source":{"type":"standard","doc":"US Army TDP drawing 9381367 (Selector, Fire Control), sheet 1 of 2, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p65: face view","via":"user"}}]},"selector_pointer_reach":{"label":"Selector pointer tip, from the selector's axis","kind":"length","measurements":[{"id":"tdp","value":0.34,"unit":"in","pm":0.005,"stated":".34 (1.15 REF = .34 + .81)","source":{"type":"standard","doc":"US Army TDP drawing 9381367 (Selector, Fire Control), sheet 1 of 2, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p65: face view","via":"user"}}]},"selector_pointer_angle":{"label":"Selector pointer included angle","kind":"angle","measurements":[{"id":"tdp","value":60,"unit":"deg","pm":2,"stated":"60° INCL ± 2.0°","source":{"type":"standard","doc":"US Army TDP drawing 9381367 (Selector, Fire Control), sheet 1 of 2, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p65: face view","via":"user"},"note":"Its flanks blend into the hub with .09 R fillets, which aren't drawn."}]},"selector_paddle_width":{"label":"Selector paddle width","kind":"length","measurements":[{"id":"tdp","value":0.25,"unit":"in","pm":0.005,"stated":".250 (full R on all stepped serrations)","source":{"type":"standard","doc":"US Army TDP drawing 9381367 (Selector, Fire Control), sheet 1 of 2, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p65: face view and View H","via":"user"}}]},"selector_paddle_reach":{"label":"Selector paddle end, from the selector's axis","kind":"length","measurements":[{"id":"tdp","value":0.81,"unit":"in","pm":0.005,"stated":".81 (also .09 + .72 REF)","source":{"type":"standard","doc":"US Army TDP drawing 9381367 (Selector, Fire Control), sheet 1 of 2, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p65: face view","via":"user"}}]},"selector_serration_height":{"label":"Selector paddle's stepped serrations, top step to the outermost step","kind":"length","measurements":[{"id":"tdp","value":0.11,"unit":"in","pm":0.005,"stated":".110 (steps .009, .025, .043, .075, .110 at widths .170 to .250)","source":{"type":"standard","doc":"US Army TDP drawing 9381367 (Selector, Fire Control), sheet 1 of 2, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p65: View H (scale 10/1)","via":"user"}}]},"selector_lever_t":{"label":"Selector lever thickness at the paddle (outer face to the receiver)","kind":"length","measurements":[{"id":"tdp","value":0.25,"unit":"in","pm":0.005,"stated":".250 (View H); 1.010 REF less .760","source":{"type":"standard","doc":"US Army TDP drawing 9381367 (Selector, Fire Control), sheet 1 of 2, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p65: View H (scale 10/1) and the view along the lever, zone D-4","via":"user"}}],"note":"Missing from 2026-09-30 to 2026-11-03: View H was read here for its serrations alone (selector_serration_height). Read again for CMMG's selector (D86, cmmg-safety-selector.lever_standoff), its six figures across are from one line, the lever's inner face, which bears on the receiver: the top terrace stands .250 off it, and the view along the lever says the same (1.010 REF less .760)."},"bolt_catch_paddle_rear_x":{"label":"Bolt catch paddle (the serrated lever on the left), rear edge, X","kind":"length","measurements":[{"id":"photo","value":3.11,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/rise-lpk f008e4862517 (Aero Precision M4A1 clone complete lower, mil-spec LPK, straight left side, 1920 px)","scaleRef":"pin frame from Hough-fitted pin heads: takedown (1781.5, 356.5), pivot (121.5, 362.5) = (0, 0), (6.375, 0): 260.4 px/in; the deck lands at 0.25 (bad-workhorse-lower.deck_above_pin 0.254)","method":"the paddle's outline on a 3x crop with a 10 px grid (px 971.7)","via":"harvest"}}]},"bolt_catch_paddle_front_x":{"label":"Bolt catch paddle, front edge, X","kind":"length","measurements":[{"id":"photo","value":3.455,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/rise-lpk f008e4862517 (Aero Precision M4A1 clone complete lower, mil-spec LPK, straight left side, 1920 px)","scaleRef":"pin frame from Hough-fitted pin heads: takedown (1781.5, 356.5), pivot (121.5, 362.5) = (0, 0), (6.375, 0): 260.4 px/in; the deck lands at 0.25 (bad-workhorse-lower.deck_above_pin 0.254)","method":"px 881.7 on the same crop; its centre (3.283) sits over the TDP's plunger hole (8448608 sheet 2, -AK-, 3.2955 by a research agent's reading)","via":"harvest"}}]},"bolt_catch_paddle_bottom_y":{"label":"Bolt catch paddle, bottom of its serrated face, Y","kind":"length","measurements":[{"id":"photo","value":0.306,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/rise-lpk f008e4862517 (Aero Precision M4A1 clone complete lower, mil-spec LPK, straight left side, 1920 px)","scaleRef":"pin frame from Hough-fitted pin heads: takedown (1781.5, 356.5), pivot (121.5, 362.5) = (0, 0), (6.375, 0): 260.4 px/in; the deck lands at 0.25 (bad-workhorse-lower.deck_above_pin 0.254)","method":"py 280 on the same crop","via":"harvest"}}]},"bolt_catch_paddle_top_y":{"label":"Bolt catch paddle, top, Y","kind":"length","measurements":[{"id":"photo","value":0.774,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/rise-lpk f008e4862517 (Aero Precision M4A1 clone complete lower, mil-spec LPK, straight left side, 1920 px)","scaleRef":"pin frame from Hough-fitted pin heads: takedown (1781.5, 356.5), pivot (121.5, 362.5) = (0, 0), (6.375, 0): 260.4 px/in; the deck lands at 0.25 (bad-workhorse-lower.deck_above_pin 0.254)","method":"py 158 on the same crop; full-round ends top and bottom (TDP 8448628 View E: FULL R 2 PLACES)","via":"harvest"}}]},"bolt_catch_t":{"label":"Bolt catch plate thickness","kind":"length","measurements":[{"id":"tdp","value":0.151,"unit":"in","pm":0.003,"stated":".151 ±.003","source":{"type":"standard","doc":"US Army TDP drawing 8448628 (Catch, Bolt), sheet 1 of 1; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p101: main view","via":"user"}}],"note":"The plate runs in the lower's slot between the bolt catch bosses (.167 +.010, TDP 8448608 View H-H by a research agent's reading); the paddle is the same plate, so it stands in that slot's plane."},"magazine_release_w":{"label":"Magazine release button, width (fore and aft)","kind":"length","measurements":[{"id":"tdp","value":0.3,"unit":"in","stated":".300 BASIC (.150 R ends)","source":{"type":"standard","doc":"US Army TDP drawing 8448636 (Button, Magazine Catch); user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p14","via":"user"}},{"id":"photo","value":0.308,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/rise-lpk a37f831793fa (US Marine Corps: M4A1 SOPMOD Block II, straight right side, 7607 px; public domain)","scaleRef":"pin frame from Hough-fitted pin heads: takedown (2303.5, 1092.5), pivot (3478.5, 1078.5) = (0, 0), (6.375, 0): 184.3 px/in","method":"the button's outline on a 4x crop (56.75 px)","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The standard; the photo agrees within its ±."}},"magazine_release_h":{"label":"Magazine release button, height","kind":"length","measurements":[{"id":"tdp","value":0.5,"unit":"in","stated":".500 BASIC","source":{"type":"standard","doc":"US Army TDP drawing 8448636 (Button, Magazine Catch); user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p14","via":"user"}},{"id":"photo","value":0.509,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/rise-lpk a37f831793fa (US Marine Corps: M4A1 SOPMOD Block II, straight right side, 7607 px; public domain)","scaleRef":"pin frame from Hough-fitted pin heads: takedown (2303.5, 1092.5), pivot (3478.5, 1078.5) = (0, 0), (6.375, 0): 184.3 px/in","method":"the button's outline on a 4x crop (93.75 px)","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The standard; the photo agrees within its ±."}},"magazine_release_standoff":{"label":"Magazine release button, how far it stands out from the receiver's body","kind":"length","measurements":[{"id":"flush","value":0.109,"unit":"in","source":{"type":"derived","expr":"{std.ar15.mag_catch_fence_out} - {std.ar15.lower_body_width} / 2"},"note":"Flush with the fence, from the body's face."}],"note":"Forward Controls Design: 'With a TDP spec magazine shaft and magazine release button, the top of the button is usually flush with the fence' (via blackrifledepot.com). The fence's face is the magazine well walls' (std.ar15.mag_catch_fence_out, 2026-10-03): the button stands out from the body's face to it."},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"redcon1","value":2.5,"unit":"oz","stated":"2.5 oz (kit)","source":{"type":"spec","publisher":"retailer","name":"R1 Tactical","url":"https://redcon1tactical.com/rise-armament-ar-15-lower-parts-kit.html","retrieved":"2026-09-30","via":"harvest"}},{"id":"landm","value":0.19,"unit":"lb","stated":"0.19 lb","source":{"type":"spec","publisher":"retailer","name":"L&M Supply","url":"https://www.landmsupply.com/rise-armament-lower-parts-kit-ar-15","retrieved":"2026-09-30","via":"harvest"}}],"adopt":{"from":"redcon1","reason":"The only figure labeled as the kit's weight. Rise publishes none, so weigh it."}}}},{"subject":"rosco-bloodline-105-barrel","title":"Rosco Manufacturing Bloodline 10.5\" M4 5.56 NATO (BL-105-M4-556-7-C)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"rosco","value":19.28,"unit":"oz","pm":0.005,"stated":"Barrel Weight 19.28 Oz","source":{"type":"spec","publisher":"manufacturer","name":"Rosco Manufacturing, Bloodline 10.5\" M4 5.56 NATO (BL-105-M4-556-7-C), Description: the specification list","url":"https://www.roscomanufacturing.com/shop/barrels/blood-line-barrels/5-56-barrels/bloodline-10-5-m4-5-56-nato/","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":19.28,"unit":"oz","pm":0.005,"stated":"19.28 oz weight","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Rosco Manufacturing Bloodline 5.56 AR-15 Barrel - Carbine - Government - 10.5\" (BL-105-M4-556-7-C), Features","url":"https://www.primaryarms.com/rosco-manufacturing-bloodline-556-barrel-government-carbine-10.5","retrieved":"2026-10-06","via":"harvest"}},{"id":"midwayusa","value":19.28,"unit":"oz","pm":0.005,"stated":"\"name\":\"Weight\",\"value\":\"19.28 Ounce\"","source":{"type":"spec","publisher":"retailer","name":"MidwayUSA, Rosco Manufacturing Bloodline AR-15 Barrel 5.56x45mm NATO 10.5\" M4 Contour 1:7\" Twist Black Nitride (product 244017, BL-105-M4-556-7-C), the page's product data","url":"https://www.midwayusa.com/product/1024526582?pid=244017","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"rosco","reason":"The maker's own figure; two sellers repeat it."}},"length":{"label":"Barrel length as its maker states it","kind":"length","measurements":[{"id":"rosco","value":10.5,"unit":"in","pm":0.05,"stated":"Barrel Length 10.5″","source":{"type":"spec","publisher":"manufacturer","name":"Rosco Manufacturing, Bloodline 10.5\" M4 5.56 NATO (BL-105-M4-556-7-C), Description: the specification list","url":"https://www.roscomanufacturing.com/shop/barrels/blood-line-barrels/5-56-barrels/bloodline-10-5-m4-5-56-nato/","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":10.5,"unit":"in","pm":0.05,"stated":"Barrel Length 10.5","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Rosco Manufacturing Bloodline 5.56 AR-15 Barrel - Carbine - Government - 10.5\" (BL-105-M4-556-7-C), Specifications","url":"https://www.primaryarms.com/rosco-manufacturing-bloodline-556-barrel-government-carbine-10.5","retrieved":"2026-10-06","via":"harvest"}},{"id":"midwayusa","value":10.5,"unit":"in","pm":0.05,"stated":"\"name\":\"Length\",\"value\":\"10.5 Inches\"","source":{"type":"spec","publisher":"retailer","name":"MidwayUSA, Rosco Manufacturing Bloodline AR-15 Barrel 5.56x45mm NATO 10.5\" M4 Contour 1:7\" Twist Black Nitride (product 244017, BL-105-M4-556-7-C), the page's product data","url":"https://www.midwayusa.com/product/1024526582?pid=244017","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"rosco","reason":"The maker's own; two sellers repeat it."},"note":"The nominal length. Rosco's page doesn't say between which points; the Army's barrel drawing (8448549) dimensions a barrel from its breech end, inside the extension, to its muzzle, and overall_length takes it so (as the catalog's other barrels do)."},"journal_od":{"label":"The gas block journal's diameter","kind":"length","measurements":[{"id":"rosco","value":0.75,"unit":"in","pm":0.0005,"stated":"Gas Block Size .750","source":{"type":"spec","publisher":"manufacturer","name":"Rosco Manufacturing, Bloodline 10.5\" M4 5.56 NATO (BL-105-M4-556-7-C), Description: the specification list","url":"https://www.roscomanufacturing.com/shop/barrels/blood-line-barrels/5-56-barrels/bloodline-10-5-m4-5-56-nato/","retrieved":"2026-10-06","via":"harvest"}},{"id":"rosco-faq","value":0.75,"unit":"in","pm":0.0005,"stated":"We currently machine the “journal” or seating area to accommodate a .750 diameter gas block for all our barrels.","source":{"type":"spec","publisher":"manufacturer","name":"Rosco Manufacturing, FAQ's: What is the size of the Gas Block seating area for your barrels?","url":"https://www.roscomanufacturing.com/faqs/","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":0.75,"unit":"in","pm":0.0005,"stated":".750\" gas seat diameter","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Rosco Manufacturing Bloodline 5.56 AR-15 Barrel - Carbine - Government - 10.5\" (BL-105-M4-556-7-C), Features","url":"https://www.primaryarms.com/rosco-manufacturing-bloodline-556-barrel-government-carbine-10.5","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"rosco","reason":"The maker's own, on this barrel's page; its FAQ says the same of every barrel, and the seller repeats it."}},"dimple_backspace":{"label":"The gas block dimple's centre ahead of the journal's rear shoulder","kind":"length","measurements":[{"id":"rosco-faq","value":0.295,"unit":"in","pm":0.0005,"stated":"Yes we do, but we only machine one dimple that is perfectly centered and matched to a backspace of .295.","source":{"type":"spec","publisher":"manufacturer","name":"Rosco Manufacturing, FAQ's: Do you dimple your barrels for Gas Blocks?","url":"https://www.roscomanufacturing.com/faqs/","retrieved":"2026-10-06","via":"harvest"}}],"note":"Rosco's FAQ, of every barrel it makes: one dimple, under the journal, \"perfectly centered\": taken as centred on the gas port opposite it (a buyer on Primary Arms' page for the 11.5: \"Index pin is in line with the gas port\"; Primary Arms' photos have the port on the marked side and the dimple, bare steel, opposite it at the same place). The one published figure for where the port is: gas_port_x is the shoulder as read plus this."},"extension_behind_breech":{"label":"The barrel extension's rear end behind the barrel's breech end","kind":"length","measurements":[{"id":"model","value":0.501,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{std.ar15.barrel_extension_behind_breech}","via":"user"}}],"note":"The standard's: the reference CAD set's extension less the Army barrel's tenon (std.ar15.barrel_extension_behind_breech), the one figure the catalog's 5.56 barrels take their breech from. Primary Arms, for this number: \"nitride-finished M4 barrel extension\"."},"bore_d":{"label":"The bore's diameter (across the lands)","kind":"length","measurements":[{"id":"tdp","value":0.219,"unit":"in","pm":0.001,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.bore_d}","via":"user"}}],"note":"The Army barrel's, as BCM's barrel's ledger read it off the drawing (8448549 sheet 2: .219 DIA): a 5.56 NATO bore. Rosco publishes none."},"index_pin_d":{"label":"The barrel indexing pin's diameter","kind":"length","measurements":[{"id":"model","value":0.125,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.index_pin_d}","via":"user"}}],"note":"The reference CAD set's pin, as BCM's barrel's ledger read it: a mil-spec extension's."},"extension_mouth_d":{"label":"The barrel extension's rear opening, its diameter at the rear face","kind":"length","measurements":[{"id":"model","value":0.77,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_mouth_d}","via":"user"}}],"note":"The inside of a mil-spec M4 extension as the reference CAD set has it, read once for BCM's barrel, for how the rear end looks. Appearance only."},"extension_mouth_chamfer":{"label":"The rear opening's chamfer, its depth (at 45°)","kind":"length","measurements":[{"id":"model","value":0.045,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_mouth_chamfer}","via":"user"}}]},"extension_lug_bore_d":{"label":"The circle the extension's locking lugs leave between their tips","kind":"length","measurements":[{"id":"model","value":0.572,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_lug_bore_d}","via":"user"}}]},"extension_lug_depth":{"label":"The locking lugs' front faces, ahead of the extension's rear end","kind":"length","measurements":[{"id":"model","value":0.214,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_lug_depth}","via":"user"}}]},"extension_recess_d":{"label":"The recess ahead of the lugs, which the bolt's lugs turn in: its diameter","kind":"length","measurements":[{"id":"model","value":0.83,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_recess_d}","via":"user"}}]},"extension_recess_depth":{"label":"The recess's front end, ahead of the extension's rear end","kind":"length","measurements":[{"id":"model","value":0.595,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_recess_depth}","via":"user"}}]},"thread_major_d":{"label":"The muzzle thread's major diameter (its crests)","kind":"length","measurements":[{"id":"tdp","value":0.4957,"unit":"in","pm":0.0033,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.thread_major_d}","via":"user"}}],"note":"The Army barrel's 1/2-28 thread (8448549 sheet 1, as BCM's barrel's ledger read it), for the 1/2 x 28 Rosco states: what the model's thread is drawn at."},"thread_minor_d":{"label":"The muzzle thread's minor diameter (its roots)","kind":"length","measurements":[{"id":"tdp","value":0.4551,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.thread_minor_d}","via":"user"}}]},"thread_pitch":{"label":"The muzzle thread's pitch","kind":"length","measurements":[{"id":"rosco","value":0.03571,"unit":"in","pm":0.00005,"stated":"Barrel Thread 1/2 x 28","source":{"type":"spec","publisher":"manufacturer","name":"Rosco Manufacturing, Bloodline 10.5\" M4 5.56 NATO (BL-105-M4-556-7-C), Description: the specification list","url":"https://www.roscomanufacturing.com/shop/barrels/blood-line-barrels/5-56-barrels/bloodline-10-5-m4-5-56-nato/","retrieved":"2026-10-06","via":"harvest"}},{"id":"rosco-faq","value":0.03571,"unit":"in","pm":0.00005,"stated":"5.56 are threaded to ½ X 28","source":{"type":"spec","publisher":"manufacturer","name":"Rosco Manufacturing, FAQ's: What thread pattern do you use for your barrels?","url":"https://www.roscomanufacturing.com/faqs/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"rosco","reason":"This barrel's own page; the FAQ says the same of every 5.56 barrel."},"note":"28 threads to the inch, by the maker's statement."},"crown_angle":{"label":"The muzzle crown's angle (its face's cone, from square to the bore)","kind":"angle","measurements":[{"id":"rosco","value":11,"unit":"deg","pm":0.5,"stated":"Barrel Crown 11 Degree","source":{"type":"spec","publisher":"manufacturer","name":"Rosco Manufacturing, Bloodline 10.5\" M4 5.56 NATO (BL-105-M4-556-7-C), Description: the specification list","url":"https://www.roscomanufacturing.com/shop/barrels/blood-line-barrels/5-56-barrels/bloodline-10-5-m4-5-56-nato/","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":11,"unit":"deg","pm":0.5,"stated":"Threaded 1/2x28, 11-degree crown","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Rosco Manufacturing Bloodline 5.56 AR-15 Barrel - Carbine - Government - 10.5\" (BL-105-M4-556-7-C), Features","url":"https://www.primaryarms.com/rosco-manufacturing-bloodline-556-barrel-government-carbine-10.5","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"rosco","reason":"The maker's own; the seller repeats it."},"note":"Rosco's FAQ: \"For the Bloodline barrels we use a 11 degree “service” crown.\" How far out across the muzzle's face it reaches isn't published."},"gas_port_d":{"label":"The gas port's diameter","kind":"length","measurements":[{"id":"buyer","value":0.073,"unit":"in","pm":0.01,"stated":".073 gas port Concentric threads Index pin is in line with the gas port","source":{"type":"spec","publisher":"review","name":"A buyer's review on Primary Arms' page for the 11.5 in barrel, BL-115-M4-556-7-C (2021-11-02)","url":"https://www.primaryarms.com/rosco-manufacturing-bloodline-556-barrel-government-carbine-11.5","retrieved":"2026-10-06","via":"harvest"}}],"note":"Rosco withholds it (FAQ: \"Unfortunately, we cannot disclose more seeing as these measurements are proprietary production information.\"), and says it is sized to each barrel. The one figure on file is a buyer's for the 11.5 in barrel, in a review on Primary Arms' page for that one, no instrument named: this 10.5 in barrel's own port isn't known, and the model cuts a hole of that size so that there is one."},"barrel_od":{"label":"The straight section between the chamber and the collar, its diameter","kind":"length","measurements":[{"id":"photo","value":0.662,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/rosco-bloodline-105-barrel 4b61a27db095 (Primary Arms' gallery, BL-105-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"its gas block journal's diameter, 133.90 px (the median over the journal's columns, the silhouette at grey 235), as the published .750 (journal_od)","method":"the straight section's width as a line along the photo, fitted over columns 879 to 1189 (119.27 px) and 1249 to 1559 (120.12 px), rms 0.13 px, carried on to the journal's columns: 118.23 px there, 0.8830 of the journal's (tools/trace.py fit_tube; .cache/rosco/pa.py) (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"The scale of the traced outline: this section, a cylinder, is what each column of the photo is scaled by (`calibrate: tube`). Its own diameter is read against the journal's published .750 on the same photo. That it is a cylinder is taken, and checked by what it predicts at the two ends of the barrel: the extension's body 0.994 (the Army's limit .999), the flange 1.167 (the reference CAD set's 1.170), the thread's crests 0.491 (the Army's 1/2-28: .4924 to .4989). The three Bloodlines' photos, each read on its own, give this section 0.662 (10.5), 0.665 (11.5), 0.666 (12.5)."},"overall_length":{"label":"End to end, the extension's rear to the muzzle","kind":"length","measurements":[{"id":"photo","value":10.97,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/rosco-bloodline-105-barrel 4b61a27db095 (Primary Arms' gallery, BL-105-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.662), its width a line along the photo (119.27 px over columns 879 to 1189, 120.12 px over 1249 to 1559): each column scaled by that line (tools/trace.py's `calibrate: tube`)","method":"its two end faces, each behind its rim's arc, at the tube's own scale with the lens's axis taken at the image's middle (tools/trace.py: read 10.975) (.cache/rosco/feat2.py)","via":"harvest"}},{"id":"published","value":11.001,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{.length} + {.extension_behind_breech}","via":"harvest"}}],"adopt":{"from":"published","reason":"Lengths at the published length, as the catalog's other barrels have them, so that barrels of different makers stand on one breech; the photo's own scale agrees with it within what the photo leaves open."},"note":"The published length from the barrel's breech end, and the extension's half inch behind that. The photo at its own scale (the journal's .750, through the straight section) reads -0.2% of it between its end faces: within what the end faces, the yaw's cosine and the lens's place leave open. The outline's lengths are set to the published figure, as the catalog's other barrels' are."},"extension_od":{"label":"The barrel extension's body, its diameter (what goes into the receiver)","kind":"length","measurements":[{"id":"tdp","value":0.999,"unit":"in","pm":0.001,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_od}","via":"user"},"note":"An upper limit: it goes into the receiver's 1.000 bore."},{"id":"photo","value":0.994,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/rosco-bloodline-105-barrel 4b61a27db095 (Primary Arms' gallery, BL-105-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.662), its width a line along the photo (119.27 px over columns 879 to 1189, 120.12 px over 1249 to 1559): each column scaled by that line (tools/trace.py's `calibrate: tube`)","method":"the extension's body, the median of its height from a quarter to three quarters of an inch ahead of its rear face (.cache/rosco/feat2.py)","via":"harvest"}}],"adopt":{"from":"photo","reason":"This barrel's own, read at the scale its journal gives through the straight section; it is under the drawing's limit, as it must be."},"note":"The photo's reading stands under the Army drawing's limit for an extension (8448548, as BCM's barrel's ledger read it: not to exceed .9990); it took no part in the scale, and is one of its three checks."},"flange_od":{"label":"The barrel extension's flange, its diameter","kind":"length","measurements":[{"id":"photo","value":1.167,"unit":"in","pm":0.007,"source":{"type":"photo","photo":"references/rosco-bloodline-105-barrel 4b61a27db095 (Primary Arms' gallery, BL-105-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.662), its width a line along the photo (119.27 px over columns 879 to 1189, 120.12 px over 1249 to 1559): each column scaled by that line (tools/trace.py's `calibrate: tube`)","method":"the flange's greatest height, on the lower of the two edges at each column (the pin, where it shows, is on one) (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"The reference CAD set's flange is 1.170 across: a check of the scale, which it took no part in."},"chamber_od":{"label":"The chamber section ahead of the flange, its diameter","kind":"length","measurements":[{"id":"photo","value":0.981,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/rosco-bloodline-105-barrel 4b61a27db095 (Primary Arms' gallery, BL-105-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.662), its width a line along the photo (119.27 px over columns 879 to 1189, 120.12 px over 1249 to 1559): each column scaled by that line (tools/trace.py's `calibrate: tube`)","method":"the median of its height over a third of an inch, a quarter inch ahead of the flange (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"The cylinder ahead of the flange, before the cone down to the straight section."},"collar_od":{"label":"The collar behind the gas block journal, its diameter","kind":"length","measurements":[{"id":"photo","value":0.851,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/rosco-bloodline-105-barrel 4b61a27db095 (Primary Arms' gallery, BL-105-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.662), its width a line along the photo (119.27 px over columns 879 to 1189, 120.12 px over 1249 to 1559): each column scaled by that line (tools/trace.py's `calibrate: tube`)","method":"the median of its height over its cylinder (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"A gas block's rear face comes back to its front face. A curved ramp leads up to it from the straight section."},"muzzle_od":{"label":"The diameter behind the muzzle thread","kind":"length","measurements":[{"id":"photo","value":0.729,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/rosco-bloodline-105-barrel 4b61a27db095 (Primary Arms' gallery, BL-105-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.662), its width a line along the photo (119.27 px over columns 879 to 1189, 120.12 px over 1249 to 1559): each column scaled by that line (tools/trace.py's `calibrate: tube`)","method":"the median of its height from a third to an eighth of an inch behind the muzzle shoulder (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"The section between the journal's front end and the muzzle shoulder: a little under the journal's .750, so a gas block slides on over it."},"extension_rear_x":{"label":"The barrel extension's rear end, from the flange's rear face (negative: inside the receiver)","kind":"length","measurements":[{"id":"photo","value":-0.98,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/rosco-bloodline-105-barrel 4b61a27db095 (Primary Arms' gallery, BL-105-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.662), its width a line along the photo (119.27 px over columns 879 to 1189, 120.12 px over 1249 to 1559): each column scaled by that line (tools/trace.py's `calibrate: tube`); lengths by (u − 1099.5)/width, then by 1.0024, which puts the two end faces the published 10.5 in and the extension's 0.501 apart (overall_length)","method":"the rear end's face, behind its rim's arc (the tool's end_face: the silhouette's tip at column 2102, the face 0.077 in ahead of it: that end is seen from 9° off square), to the flange's rear face (column 1906.1: the flange's rim fitted as an ellipse between the body's radius and its own, seen from 9° off square) (.cache/rosco/feat2.py)","via":"harvest"}},{"id":"model","value":-0.99,"unit":"in","pm":0.007,"source":{"type":"derived","expr":"{std.ar15.barrel_extension_flange_thickness} - {std.ar15.barrel_extension_length}","via":"user"},"note":"A mil-spec extension as the reference CAD set has it: the standard's, not this barrel's."}],"adopt":{"from":"photo","reason":"This barrel's own photo, which the outline is cut and placed by; the standard extension's is within its ±."},"note":"The reference CAD set's extension has 0.990 here (its 1.121 less its 0.131 flange); BCM's barrel read 0.984. The outline is cut and placed by the photo's reading."},"flange_front_x":{"label":"The extension flange's front face, ahead of its rear face (the flange's thickness)","kind":"length","measurements":[{"id":"photo","value":0.097,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/rosco-bloodline-105-barrel 4b61a27db095 (Primary Arms' gallery, BL-105-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.662), its width a line along the photo (119.27 px over columns 879 to 1189, 120.12 px over 1249 to 1559): each column scaled by that line (tools/trace.py's `calibrate: tube`); lengths by (u − 1099.5)/width, then by 1.0024, which puts the two end faces the published 10.5 in and the extension's 0.501 apart (overall_length)","method":"the flange's rear face (column 1906.1) to its front face (column 1888.2), each where its rim's ellipse, fitted on the silhouette between the neighbour's radius and the flange's, comes to the flange's full radius (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"The reference CAD set's flange is 0.131 thick; BCM's barrel read 0.095. At mid-height the silhouette is twice this wide: each face's rim is an ellipse, the rear one's near half standing behind its face and the front one's far half ahead of it."},"taper_rear_x":{"label":"Where the cone ahead of the chamber section begins, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":0.784,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/rosco-bloodline-105-barrel 4b61a27db095 (Primary Arms' gallery, BL-105-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.662), its width a line along the photo (119.27 px over columns 879 to 1189, 120.12 px over 1249 to 1559): each column scaled by that line (tools/trace.py's `calibrate: tube`); lengths by (u − 1099.5)/width, then by 1.0024, which puts the two end faces the published 10.5 in and the extension's 0.501 apart (overall_length)","method":"the flange's rear face (column 1906.1) to where the line through the cone's middle (between a fifth and four fifths of its drop) meets the chamber section's diameter (column 1761.7) (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"The cone is straight: a line through its middle meets the chamber section's cylinder here."},"taper_front_x":{"label":"Where that cone ends and the straight section begins, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":1.63,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/rosco-bloodline-105-barrel 4b61a27db095 (Primary Arms' gallery, BL-105-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.662), its width a line along the photo (119.27 px over columns 879 to 1189, 120.12 px over 1249 to 1559): each column scaled by that line (tools/trace.py's `calibrate: tube`); lengths by (u − 1099.5)/width, then by 1.0024, which puts the two end faces the published 10.5 in and the extension's 0.501 apart (overall_length)","method":"the flange's rear face (column 1906.1) to where the same line meets the straight section's diameter (column 1606.5) (.cache/rosco/feat2.py)","via":"harvest"}}]},"ramp_rear_x":{"label":"Where the ramp up to the collar leaves the straight section, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":5.832,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/rosco-bloodline-105-barrel 4b61a27db095 (Primary Arms' gallery, BL-105-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.662), its width a line along the photo (119.27 px over columns 879 to 1189, 120.12 px over 1249 to 1559): each column scaled by that line (tools/trace.py's `calibrate: tube`); lengths by (u − 1099.5)/width, then by 1.0024, which puts the two end faces the published 10.5 in and the extension's 0.501 apart (overall_length)","method":"the flange's rear face (column 1906.1) to where the height first stands 0.006 over the straight section's (column 847.3) (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"The ramp is curved: shallow where it leaves the straight section, steeper into the collar. The model follows the outline along it."},"collar_rear_x":{"label":"Where the ramp reaches the collar's cylinder, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":6.293,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/rosco-bloodline-105-barrel 4b61a27db095 (Primary Arms' gallery, BL-105-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.662), its width a line along the photo (119.27 px over columns 879 to 1189, 120.12 px over 1249 to 1559): each column scaled by that line (tools/trace.py's `calibrate: tube`); lengths by (u − 1099.5)/width, then by 1.0024, which puts the two end faces the published 10.5 in and the extension's 0.501 apart (overall_length)","method":"the flange's rear face (column 1906.1) to where the height comes within 0.006 of the collar's (column 765.2) (.cache/rosco/feat2.py)","via":"harvest"}}]},"journal_rear_x":{"label":"The gas block journal's rear shoulder (the collar's front face) ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":6.913,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/rosco-bloodline-105-barrel 4b61a27db095 (Primary Arms' gallery, BL-105-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.662), its width a line along the photo (119.27 px over columns 879 to 1189, 120.12 px over 1249 to 1559): each column scaled by that line (tools/trace.py's `calibrate: tube`); lengths by (u − 1099.5)/width, then by 1.0024, which puts the two end faces the published 10.5 in and the extension's 0.501 apart (overall_length)","method":"the flange's rear face (column 1906.1) to the collar's front face (column 655.0): the collar's rim fitted as an ellipse on the silhouette between the journal's radius and the collar's (seen from 11° off square, rms 0.001 in) (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"A gas block's rear face comes back to this shoulder, and Rosco places the dimple, and with it the port, from it (dimple_backspace). The three Bloodlines' own photos put it 6.91 (10.5), 6.94 (11.5), 6.93 (12.5) in ahead of the receiver: one carbine port."},"journal_front_x":{"label":"The gas block journal's front end (where the barrel steps down) ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":8.859,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/rosco-bloodline-105-barrel 4b61a27db095 (Primary Arms' gallery, BL-105-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.662), its width a line along the photo (119.27 px over columns 879 to 1189, 120.12 px over 1249 to 1559): each column scaled by that line (tools/trace.py's `calibrate: tube`); lengths by (u − 1099.5)/width, then by 1.0024, which puts the two end faces the published 10.5 in and the extension's 0.501 apart (overall_length)","method":"the flange's rear face (column 1906.1) to where the height is midway between the journal's and the next section's (column 308.9), less its rim's arc there (0.017) (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"The journal is 1.95 long; ahead of it the barrel is 0.729 across to the muzzle shoulder. The step is a short cone, a tenth of an inch long."},"gas_port_x":{"label":"The gas port ahead of the extension's face","kind":"length","measurements":[{"id":"published","value":7.208,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.journal_rear_x} + {.dimple_backspace}","via":"harvest"},"note":"The shoulder as the photo has it, and the maker's figure from there."},{"id":"photo","value":7.19,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/rosco-bloodline-105-barrel 4b61a27db095 (Primary Arms' gallery, BL-105-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.662), its width a line along the photo (119.27 px over columns 879 to 1189, 120.12 px over 1249 to 1559): each column scaled by that line (tools/trace.py's `calibrate: tube`); lengths by (u − 1099.5)/width, then by 1.0024, which puts the two end faces the published 10.5 in and the extension's 0.501 apart (overall_length)","method":"the flange's rear face (column 1906.1) to the dimple's bright dot of bare steel on the journal (centred column 595.7, row 771.8: 0.58 of the journal's radius off the axis): 0.335 ahead of the collar's front face as it shows, less 0.058 for its standing toward the lens by the rest of that radius, at a place seen from 11° off square (.cache/rosco/feat2.py)","via":"harvest"}}],"adopt":{"from":"published","reason":"The maker's own figure for where the dimple is from the shoulder; the photo's dot agrees with it within the photo's ±."},"note":"Rosco gives no distance from the receiver; its FAQ gives the dimple's from the journal's shoulder (dimple_backspace, .295), and the dimple is opposite the port. From the barrel's breech end this port is 7.69 in. The photo has the dimple as a bright dot on the journal, 0.276 ahead of the collar's front face: within 0.02 of where the FAQ puts it."},"shoulder_x":{"label":"The muzzle shoulder ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":9.41,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/rosco-bloodline-105-barrel 4b61a27db095 (Primary Arms' gallery, BL-105-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.662), its width a line along the photo (119.27 px over columns 879 to 1189, 120.12 px over 1249 to 1559): each column scaled by that line (tools/trace.py's `calibrate: tube`); lengths by (u − 1099.5)/width, then by 1.0024, which puts the two end faces the published 10.5 in and the extension's 0.501 apart (overall_length)","method":"the flange's rear face (column 1906.1) to the muzzle shoulder's face (column 215.5): where the thread's edge meets the shoulder's silhouette and up to 0.035 under its rim, the silhouette is the rim's arc, an ellipse about the face at the obliquity its neighbours give (17°); 12 points agree on the face to 0.001 in. The ± is the obliquity's and the length's scale (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"Where the thread begins: a muzzle device or its washer seats here. The lens sees it from well off square: at mid-height the silhouette stands ahead of the face by its rim's arc."},"thread_length":{"label":"The muzzle thread's length","kind":"length","measurements":[{"id":"photo","value":0.611,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/rosco-bloodline-105-barrel 4b61a27db095 (Primary Arms' gallery, BL-105-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.662), its width a line along the photo (119.27 px over columns 879 to 1189, 120.12 px over 1249 to 1559): each column scaled by that line (tools/trace.py's `calibrate: tube`); lengths by (u − 1099.5)/width, then by 1.0024, which puts the two end faces the published 10.5 in and the extension's 0.501 apart (overall_length)","method":"the shoulder's face (column 215.5) to the muzzle's face, behind its rim's arc (the tool's end_face: the tip at column 95, seen from 18° off square) (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"The Army barrel's is .63 (8448549); BCM's barrel read 0.50."},"index_pin_x":{"label":"The barrel indexing pin's axis behind the flange's rear face","kind":"length","measurements":[{"id":"sibling","value":0.072,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{rosco-bloodline-115-barrel.index_pin_x}","via":"harvest"}}],"note":"This barrel's own side photo has the pin turned out of the silhouette (the dimple, opposite it, faces the lens). Taken from the 11.5 in Bloodline's photo: the same M4 extension, by the pin's standard place on one (the reference CAD set: 0.0765 behind the flange's rear face). The one figure here that is a sibling's."},"index_pin_top":{"label":"The barrel indexing pin's top above the bore's axis","kind":"length","measurements":[{"id":"sibling","value":0.582,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{rosco-bloodline-115-barrel.index_pin_top}","via":"harvest"}}],"note":"This barrel's own side photo has the pin turned out of the silhouette (the dimple, opposite it, faces the lens). Taken from the 11.5 in Bloodline's photo: the same M4 extension, by the pin's standard place on one (the reference CAD set: 0.0765 behind the flange's rear face). The one figure here that is a sibling's."},"outline_rear_face":{"label":"The extension's rear face in the traced outline's own frame (from the silhouette's rear tip)","kind":"length","measurements":[{"id":"photo","value":0.077,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/rosco-bloodline-105-barrel 4b61a27db095 (Primary Arms' gallery, BL-105-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"scale from rosco-bloodline-105-barrel.barrel_od = 0.662 in, the tube's own width column by column: 119.3 px over columns 879–1189, 120.1 px over columns 1249–1559; a line through them (rms 0.13 px) changes +1.1% from column 879 to 1559, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 180.4 px/in there. The axis is the tube's centre line (tilt -0.02°, rms 0.04 px). Lengths then scaled by 1.0024 so that the end faces are rosco-bloodline-105-barrel.overall_length = 11.001 in apart: at the tube's scale they read 10.975 (-0.2%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.090 in over radius 0.244 (rms 0.002), the rear end's rim sags 0.068 in over radius 0.491 (rms 0.012)","method":"the min end's face: the silhouette's tip at 0.010 less its rim's arc, 0.068 in of sag at radius 0.490583 (the end is seen from 7.9° off square; arc fitted over 121 rows, rms 0.012) of the traced outline (tools/trace.py); the extension's rear face in the outline's own frame (from its rear tip)","via":"harvest"}}]},"outline_front_face":{"label":"The muzzle's face in the traced outline's own frame (from the silhouette's rear tip)","kind":"length","measurements":[{"id":"photo","value":11.078,"unit":"in","pm":0.076,"source":{"type":"photo","photo":"references/rosco-bloodline-105-barrel 4b61a27db095 (Primary Arms' gallery, BL-105-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"scale from rosco-bloodline-105-barrel.barrel_od = 0.662 in, the tube's own width column by column: 119.3 px over columns 879–1189, 120.1 px over columns 1249–1559; a line through them (rms 0.13 px) changes +1.1% from column 879 to 1559, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 180.4 px/in there. The axis is the tube's centre line (tilt -0.02°, rms 0.04 px). Lengths then scaled by 1.0024 so that the end faces are rosco-bloodline-105-barrel.overall_length = 11.001 in apart: at the tube's scale they read 10.975 (-0.2%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.090 in over radius 0.244 (rms 0.002), the rear end's rim sags 0.068 in over radius 0.491 (rms 0.012)","method":"the max end's face: the silhouette's tip at 11.168 less its rim's arc, 0.090 in of sag at radius 0.24407 (the end is seen from 20.2° off square; arc fitted over 120 rows, rms 0.002) of the traced outline (tools/trace.py); the muzzle's face in the outline's own frame (from its rear tip)","via":"harvest"}}]}}},{"subject":"rosco-bloodline-115-barrel","title":"Rosco Manufacturing Bloodline 11.5\" M4 5.56 NATO (BL-115-M4-556-7-C)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"rosco","value":20.82,"unit":"oz","pm":0.005,"stated":"Barrel Weight 20.82 Oz","source":{"type":"spec","publisher":"manufacturer","name":"Rosco Manufacturing, Bloodline 11.5\" M4 5.56 NATO (BL-115-M4-556-7-C), Description: the specification list","url":"https://www.roscomanufacturing.com/shop/barrels/blood-line-barrels/5-56-barrels/bloodline-11-5-m4-5-56-nato/","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":20.82,"unit":"oz","pm":0.005,"stated":"20.82 oz weight","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Rosco Manufacturing Bloodline 5.56 AR-15 Barrel - Carbine - Government - 11.5\" (BL-115-M4-556-7-C), Features","url":"https://www.primaryarms.com/rosco-manufacturing-bloodline-556-barrel-government-carbine-11.5","retrieved":"2026-10-06","via":"harvest"}},{"id":"midwayusa","value":20.82,"unit":"oz","pm":0.005,"stated":"\"name\":\"Weight\",\"value\":\"20.82 Ounce\"","source":{"type":"spec","publisher":"retailer","name":"MidwayUSA, Rosco Manufacturing Bloodline AR-15 Barrel 5.56x45mm NATO 11.5\" M4 Contour 1:7\" Twist Black Nitride (product 638416, BL-115-M4-556-7-C), the page's product data","url":"https://www.midwayusa.com/product/1024526582?pid=638416","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"rosco","reason":"The maker's own figure; two sellers repeat it."}},"length":{"label":"Barrel length as its maker states it","kind":"length","measurements":[{"id":"rosco","value":11.5,"unit":"in","pm":0.05,"stated":"Barrel Length 11.5″","source":{"type":"spec","publisher":"manufacturer","name":"Rosco Manufacturing, Bloodline 11.5\" M4 5.56 NATO (BL-115-M4-556-7-C), Description: the specification list","url":"https://www.roscomanufacturing.com/shop/barrels/blood-line-barrels/5-56-barrels/bloodline-11-5-m4-5-56-nato/","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":11.5,"unit":"in","pm":0.05,"stated":"Barrel Length 11.5","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Rosco Manufacturing Bloodline 5.56 AR-15 Barrel - Carbine - Government - 11.5\" (BL-115-M4-556-7-C), Specifications","url":"https://www.primaryarms.com/rosco-manufacturing-bloodline-556-barrel-government-carbine-11.5","retrieved":"2026-10-06","via":"harvest"}},{"id":"midwayusa","value":11.5,"unit":"in","pm":0.05,"stated":"\"name\":\"Length\",\"value\":\"11.5 Inches\"","source":{"type":"spec","publisher":"retailer","name":"MidwayUSA, Rosco Manufacturing Bloodline AR-15 Barrel 5.56x45mm NATO 11.5\" M4 Contour 1:7\" Twist Black Nitride (product 638416, BL-115-M4-556-7-C), the page's product data","url":"https://www.midwayusa.com/product/1024526582?pid=638416","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"rosco","reason":"The maker's own; two sellers repeat it."},"note":"The nominal length. Rosco's page doesn't say between which points; the Army's barrel drawing (8448549) dimensions a barrel from its breech end, inside the extension, to its muzzle, and overall_length takes it so (as the catalog's other barrels do)."},"journal_od":{"label":"The gas block journal's diameter","kind":"length","measurements":[{"id":"rosco","value":0.75,"unit":"in","pm":0.0005,"stated":"Gas Block Size .750","source":{"type":"spec","publisher":"manufacturer","name":"Rosco Manufacturing, Bloodline 11.5\" M4 5.56 NATO (BL-115-M4-556-7-C), Description: the specification list","url":"https://www.roscomanufacturing.com/shop/barrels/blood-line-barrels/5-56-barrels/bloodline-11-5-m4-5-56-nato/","retrieved":"2026-10-06","via":"harvest"}},{"id":"rosco-faq","value":0.75,"unit":"in","pm":0.0005,"stated":"We currently machine the “journal” or seating area to accommodate a .750 diameter gas block for all our barrels.","source":{"type":"spec","publisher":"manufacturer","name":"Rosco Manufacturing, FAQ's: What is the size of the Gas Block seating area for your barrels?","url":"https://www.roscomanufacturing.com/faqs/","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":0.75,"unit":"in","pm":0.0005,"stated":".750\" gas seat diameter","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Rosco Manufacturing Bloodline 5.56 AR-15 Barrel - Carbine - Government - 11.5\" (BL-115-M4-556-7-C), Features","url":"https://www.primaryarms.com/rosco-manufacturing-bloodline-556-barrel-government-carbine-11.5","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"rosco","reason":"The maker's own, on this barrel's page; its FAQ says the same of every barrel, and the seller repeats it."}},"dimple_backspace":{"label":"The gas block dimple's centre ahead of the journal's rear shoulder","kind":"length","measurements":[{"id":"rosco-faq","value":0.295,"unit":"in","pm":0.0005,"stated":"Yes we do, but we only machine one dimple that is perfectly centered and matched to a backspace of .295.","source":{"type":"spec","publisher":"manufacturer","name":"Rosco Manufacturing, FAQ's: Do you dimple your barrels for Gas Blocks?","url":"https://www.roscomanufacturing.com/faqs/","retrieved":"2026-10-06","via":"harvest"}}],"note":"Rosco's FAQ, of every barrel it makes: one dimple, under the journal, \"perfectly centered\": taken as centred on the gas port opposite it (a buyer on Primary Arms' page for the 11.5: \"Index pin is in line with the gas port\"; Primary Arms' photos have the port on the marked side and the dimple, bare steel, opposite it at the same place). The one published figure for where the port is: gas_port_x is the shoulder as read plus this."},"extension_behind_breech":{"label":"The barrel extension's rear end behind the barrel's breech end","kind":"length","measurements":[{"id":"model","value":0.501,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{std.ar15.barrel_extension_behind_breech}","via":"user"}}],"note":"The standard's: the reference CAD set's extension less the Army barrel's tenon (std.ar15.barrel_extension_behind_breech), the one figure the catalog's 5.56 barrels take their breech from. Primary Arms, for this number: \"nitride-finished M4 barrel extension\"."},"bore_d":{"label":"The bore's diameter (across the lands)","kind":"length","measurements":[{"id":"tdp","value":0.219,"unit":"in","pm":0.001,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.bore_d}","via":"user"}}],"note":"The Army barrel's, as BCM's barrel's ledger read it off the drawing (8448549 sheet 2: .219 DIA): a 5.56 NATO bore. Rosco publishes none."},"index_pin_d":{"label":"The barrel indexing pin's diameter","kind":"length","measurements":[{"id":"model","value":0.125,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.index_pin_d}","via":"user"}}],"note":"The reference CAD set's pin, as BCM's barrel's ledger read it: a mil-spec extension's."},"extension_mouth_d":{"label":"The barrel extension's rear opening, its diameter at the rear face","kind":"length","measurements":[{"id":"model","value":0.77,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_mouth_d}","via":"user"}}],"note":"The inside of a mil-spec M4 extension as the reference CAD set has it, read once for BCM's barrel, for how the rear end looks. Appearance only."},"extension_mouth_chamfer":{"label":"The rear opening's chamfer, its depth (at 45°)","kind":"length","measurements":[{"id":"model","value":0.045,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_mouth_chamfer}","via":"user"}}]},"extension_lug_bore_d":{"label":"The circle the extension's locking lugs leave between their tips","kind":"length","measurements":[{"id":"model","value":0.572,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_lug_bore_d}","via":"user"}}]},"extension_lug_depth":{"label":"The locking lugs' front faces, ahead of the extension's rear end","kind":"length","measurements":[{"id":"model","value":0.214,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_lug_depth}","via":"user"}}]},"extension_recess_d":{"label":"The recess ahead of the lugs, which the bolt's lugs turn in: its diameter","kind":"length","measurements":[{"id":"model","value":0.83,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_recess_d}","via":"user"}}]},"extension_recess_depth":{"label":"The recess's front end, ahead of the extension's rear end","kind":"length","measurements":[{"id":"model","value":0.595,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_recess_depth}","via":"user"}}]},"thread_major_d":{"label":"The muzzle thread's major diameter (its crests)","kind":"length","measurements":[{"id":"tdp","value":0.4957,"unit":"in","pm":0.0033,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.thread_major_d}","via":"user"}}],"note":"The Army barrel's 1/2-28 thread (8448549 sheet 1, as BCM's barrel's ledger read it), for the 1/2 x 28 Rosco states: what the model's thread is drawn at."},"thread_minor_d":{"label":"The muzzle thread's minor diameter (its roots)","kind":"length","measurements":[{"id":"tdp","value":0.4551,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.thread_minor_d}","via":"user"}}]},"thread_pitch":{"label":"The muzzle thread's pitch","kind":"length","measurements":[{"id":"rosco","value":0.03571,"unit":"in","pm":0.00005,"stated":"Barrel Thread 1/2 x 28","source":{"type":"spec","publisher":"manufacturer","name":"Rosco Manufacturing, Bloodline 11.5\" M4 5.56 NATO (BL-115-M4-556-7-C), Description: the specification list","url":"https://www.roscomanufacturing.com/shop/barrels/blood-line-barrels/5-56-barrels/bloodline-11-5-m4-5-56-nato/","retrieved":"2026-10-06","via":"harvest"}},{"id":"rosco-faq","value":0.03571,"unit":"in","pm":0.00005,"stated":"5.56 are threaded to ½ X 28","source":{"type":"spec","publisher":"manufacturer","name":"Rosco Manufacturing, FAQ's: What thread pattern do you use for your barrels?","url":"https://www.roscomanufacturing.com/faqs/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"rosco","reason":"This barrel's own page; the FAQ says the same of every 5.56 barrel."},"note":"28 threads to the inch, by the maker's statement."},"crown_angle":{"label":"The muzzle crown's angle (its face's cone, from square to the bore)","kind":"angle","measurements":[{"id":"rosco","value":11,"unit":"deg","pm":0.5,"stated":"Barrel Crown 11 Degree","source":{"type":"spec","publisher":"manufacturer","name":"Rosco Manufacturing, Bloodline 11.5\" M4 5.56 NATO (BL-115-M4-556-7-C), Description: the specification list","url":"https://www.roscomanufacturing.com/shop/barrels/blood-line-barrels/5-56-barrels/bloodline-11-5-m4-5-56-nato/","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":11,"unit":"deg","pm":0.5,"stated":"Threaded 1/2x28, 11-degree crown","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Rosco Manufacturing Bloodline 5.56 AR-15 Barrel - Carbine - Government - 11.5\" (BL-115-M4-556-7-C), Features","url":"https://www.primaryarms.com/rosco-manufacturing-bloodline-556-barrel-government-carbine-11.5","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"rosco","reason":"The maker's own; the seller repeats it."},"note":"Rosco's FAQ: \"For the Bloodline barrels we use a 11 degree “service” crown.\" How far out across the muzzle's face it reaches isn't published."},"gas_port_d":{"label":"The gas port's diameter","kind":"length","measurements":[{"id":"buyer","value":0.073,"unit":"in","pm":0.002,"stated":".073 gas port Concentric threads Index pin is in line with the gas port","source":{"type":"spec","publisher":"review","name":"A buyer's review on Primary Arms' page for the 11.5 in barrel, BL-115-M4-556-7-C (2021-11-02)","url":"https://www.primaryarms.com/rosco-manufacturing-bloodline-556-barrel-government-carbine-11.5","retrieved":"2026-10-06","via":"harvest"}}],"note":"Rosco withholds it (FAQ: \"Unfortunately, we cannot disclose more seeing as these measurements are proprietary production information.\"), and says it is sized to each barrel. The one figure on file is a buyer's for the 11.5 in barrel, in a review on Primary Arms' page for that one, no instrument named: for the hole the model cuts, nothing else."},"barrel_od":{"label":"The straight section between the chamber and the collar, its diameter","kind":"length","measurements":[{"id":"photo","value":0.665,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/rosco-bloodline-115-barrel 4aaee849158f (Primary Arms' gallery, BL-115-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"its gas block journal's diameter, 123.10 px (the median over the journal's columns, the silhouette at grey 235), as the published .750 (journal_od)","method":"the straight section's width as a line along the photo, fitted over columns 949 to 1139 (110.20 px) and 1199 to 1629 (111.16 px), rms 0.25 px, carried on to the journal's columns: 109.10 px there, 0.8863 of the journal's (tools/trace.py fit_tube; .cache/rosco/pa.py) (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"The scale of the traced outline: this section, a cylinder, is what each column of the photo is scaled by (`calibrate: tube`). Its own diameter is read against the journal's published .750 on the same photo. That it is a cylinder is taken, and checked by what it predicts at the two ends of the barrel: the extension's body 0.995 (the Army's limit .999), the flange 1.171 (the reference CAD set's 1.170), the thread's crests 0.490 (the Army's 1/2-28: .4924 to .4989). The three Bloodlines' photos, each read on its own, give this section 0.662 (10.5), 0.665 (11.5), 0.666 (12.5)."},"overall_length":{"label":"End to end, the extension's rear to the muzzle","kind":"length","measurements":[{"id":"photo","value":11.91,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/rosco-bloodline-115-barrel 4aaee849158f (Primary Arms' gallery, BL-115-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.665), its width a line along the photo (110.20 px over columns 949 to 1139, 111.16 px over 1199 to 1629): each column scaled by that line (tools/trace.py's `calibrate: tube`)","method":"its two end faces, each behind its rim's arc, at the tube's own scale with the lens's axis taken at the image's middle (tools/trace.py: read 11.908) (.cache/rosco/feat2.py)","via":"harvest"}},{"id":"published","value":12.001,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{.length} + {.extension_behind_breech}","via":"harvest"}}],"adopt":{"from":"published","reason":"Lengths at the published length, as the catalog's other barrels have them, so that barrels of different makers stand on one breech; the photo's own scale agrees with it within what the photo leaves open."},"note":"The published length from the barrel's breech end, and the extension's half inch behind that. The photo at its own scale (the journal's .750, through the straight section) reads -0.8% of it between its end faces: within what the end faces, the yaw's cosine and the lens's place leave open. The outline's lengths are set to the published figure, as the catalog's other barrels' are."},"extension_od":{"label":"The barrel extension's body, its diameter (what goes into the receiver)","kind":"length","measurements":[{"id":"tdp","value":0.999,"unit":"in","pm":0.001,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_od}","via":"user"},"note":"An upper limit: it goes into the receiver's 1.000 bore."},{"id":"photo","value":0.995,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/rosco-bloodline-115-barrel 4aaee849158f (Primary Arms' gallery, BL-115-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.665), its width a line along the photo (110.20 px over columns 949 to 1139, 111.16 px over 1199 to 1629): each column scaled by that line (tools/trace.py's `calibrate: tube`)","method":"the extension's body, the median of its height from a quarter to three quarters of an inch ahead of its rear face (.cache/rosco/feat2.py)","via":"harvest"}}],"adopt":{"from":"photo","reason":"This barrel's own, read at the scale its journal gives through the straight section; it is under the drawing's limit, as it must be."},"note":"The photo's reading stands under the Army drawing's limit for an extension (8448548, as BCM's barrel's ledger read it: not to exceed .9990); it took no part in the scale, and is one of its three checks."},"flange_od":{"label":"The barrel extension's flange, its diameter","kind":"length","measurements":[{"id":"photo","value":1.171,"unit":"in","pm":0.007,"source":{"type":"photo","photo":"references/rosco-bloodline-115-barrel 4aaee849158f (Primary Arms' gallery, BL-115-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.665), its width a line along the photo (110.20 px over columns 949 to 1139, 111.16 px over 1199 to 1629): each column scaled by that line (tools/trace.py's `calibrate: tube`)","method":"the flange's greatest height, on the lower of the two edges at each column (the pin, where it shows, is on one) (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"The reference CAD set's flange is 1.170 across: a check of the scale, which it took no part in."},"chamber_od":{"label":"The chamber section ahead of the flange, its diameter","kind":"length","measurements":[{"id":"photo","value":0.984,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/rosco-bloodline-115-barrel 4aaee849158f (Primary Arms' gallery, BL-115-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.665), its width a line along the photo (110.20 px over columns 949 to 1139, 111.16 px over 1199 to 1629): each column scaled by that line (tools/trace.py's `calibrate: tube`)","method":"the median of its height over a third of an inch, a quarter inch ahead of the flange (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"The cylinder ahead of the flange, before the cone down to the straight section."},"collar_od":{"label":"The collar behind the gas block journal, its diameter","kind":"length","measurements":[{"id":"photo","value":0.856,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/rosco-bloodline-115-barrel 4aaee849158f (Primary Arms' gallery, BL-115-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.665), its width a line along the photo (110.20 px over columns 949 to 1139, 111.16 px over 1199 to 1629): each column scaled by that line (tools/trace.py's `calibrate: tube`)","method":"the median of its height over its cylinder (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"A gas block's rear face comes back to its front face. A curved ramp leads up to it from the straight section."},"muzzle_od":{"label":"The diameter behind the muzzle thread","kind":"length","measurements":[{"id":"photo","value":0.724,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/rosco-bloodline-115-barrel 4aaee849158f (Primary Arms' gallery, BL-115-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.665), its width a line along the photo (110.20 px over columns 949 to 1139, 111.16 px over 1199 to 1629): each column scaled by that line (tools/trace.py's `calibrate: tube`)","method":"the median of its height from a third to an eighth of an inch behind the muzzle shoulder (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"The section between the journal's front end and the muzzle shoulder: a little under the journal's .750, so a gas block slides on over it."},"extension_rear_x":{"label":"The barrel extension's rear end, from the flange's rear face (negative: inside the receiver)","kind":"length","measurements":[{"id":"photo","value":-0.972,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/rosco-bloodline-115-barrel 4aaee849158f (Primary Arms' gallery, BL-115-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.665), its width a line along the photo (110.20 px over columns 949 to 1139, 111.16 px over 1199 to 1629): each column scaled by that line (tools/trace.py's `calibrate: tube`); lengths by (u − 1099.5)/width, then by 1.0078, which puts the two end faces the published 11.5 in and the extension's 0.501 apart (overall_length)","method":"the rear end's face, behind its rim's arc (the tool's end_face: the silhouette's tip at column 2104, the face 0.114 in ahead of it: that end is seen from 13° off square), to the flange's rear face (column 1918.0: the flange's rim fitted as an ellipse between the body's radius and its own, seen from 12° off square) (.cache/rosco/feat2.py)","via":"harvest"}},{"id":"model","value":-0.99,"unit":"in","pm":0.007,"source":{"type":"derived","expr":"{std.ar15.barrel_extension_flange_thickness} - {std.ar15.barrel_extension_length}","via":"user"},"note":"A mil-spec extension as the reference CAD set has it: the standard's, not this barrel's."}],"adopt":{"from":"photo","reason":"This barrel's own photo, which the outline is cut and placed by; the standard extension's is within its ±."},"note":"The reference CAD set's extension has 0.990 here (its 1.121 less its 0.131 flange); BCM's barrel read 0.984. The outline is cut and placed by the photo's reading."},"flange_front_x":{"label":"The extension flange's front face, ahead of its rear face (the flange's thickness)","kind":"length","measurements":[{"id":"photo","value":0.095,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/rosco-bloodline-115-barrel 4aaee849158f (Primary Arms' gallery, BL-115-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.665), its width a line along the photo (110.20 px over columns 949 to 1139, 111.16 px over 1199 to 1629): each column scaled by that line (tools/trace.py's `calibrate: tube`); lengths by (u − 1099.5)/width, then by 1.0078, which puts the two end faces the published 11.5 in and the extension's 0.501 apart (overall_length)","method":"the flange's rear face (column 1918.0) to its front face (column 1901.8), each where its rim's ellipse, fitted on the silhouette between the neighbour's radius and the flange's, comes to the flange's full radius (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"The reference CAD set's flange is 0.131 thick; BCM's barrel read 0.095. At mid-height the silhouette is twice this wide: each face's rim is an ellipse, the rear one's near half standing behind its face and the front one's far half ahead of it."},"taper_rear_x":{"label":"Where the cone ahead of the chamber section begins, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":0.786,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/rosco-bloodline-115-barrel 4aaee849158f (Primary Arms' gallery, BL-115-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.665), its width a line along the photo (110.20 px over columns 949 to 1139, 111.16 px over 1199 to 1629): each column scaled by that line (tools/trace.py's `calibrate: tube`); lengths by (u − 1099.5)/width, then by 1.0078, which puts the two end faces the published 11.5 in and the extension's 0.501 apart (overall_length)","method":"the flange's rear face (column 1918.0) to where the line through the cone's middle (between a fifth and four fifths of its drop) meets the chamber section's diameter (column 1784.3) (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"The cone is straight: a line through its middle meets the chamber section's cylinder here."},"taper_front_x":{"label":"Where that cone ends and the straight section begins, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":1.632,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/rosco-bloodline-115-barrel 4aaee849158f (Primary Arms' gallery, BL-115-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.665), its width a line along the photo (110.20 px over columns 949 to 1139, 111.16 px over 1199 to 1629): each column scaled by that line (tools/trace.py's `calibrate: tube`); lengths by (u − 1099.5)/width, then by 1.0078, which puts the two end faces the published 11.5 in and the extension's 0.501 apart (overall_length)","method":"the flange's rear face (column 1918.0) to where the same line meets the straight section's diameter (column 1641.2) (.cache/rosco/feat2.py)","via":"harvest"}}]},"ramp_rear_x":{"label":"Where the ramp up to the collar leaves the straight section, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":5.933,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/rosco-bloodline-115-barrel 4aaee849158f (Primary Arms' gallery, BL-115-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.665), its width a line along the photo (110.20 px over columns 949 to 1139, 111.16 px over 1199 to 1629): each column scaled by that line (tools/trace.py's `calibrate: tube`); lengths by (u − 1099.5)/width, then by 1.0078, which puts the two end faces the published 11.5 in and the extension's 0.501 apart (overall_length)","method":"the flange's rear face (column 1918.0) to where the height first stands 0.006 over the straight section's (column 927.3) (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"The ramp is curved: shallow where it leaves the straight section, steeper into the collar. The model follows the outline along it."},"collar_rear_x":{"label":"Where the ramp reaches the collar's cylinder, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":6.303,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/rosco-bloodline-115-barrel 4aaee849158f (Primary Arms' gallery, BL-115-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.665), its width a line along the photo (110.20 px over columns 949 to 1139, 111.16 px over 1199 to 1629): each column scaled by that line (tools/trace.py's `calibrate: tube`); lengths by (u − 1099.5)/width, then by 1.0078, which puts the two end faces the published 11.5 in and the extension's 0.501 apart (overall_length)","method":"the flange's rear face (column 1918.0) to where the height comes within 0.006 of the collar's (column 866.9) (.cache/rosco/feat2.py)","via":"harvest"}}]},"journal_rear_x":{"label":"The gas block journal's rear shoulder (the collar's front face) ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":6.943,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/rosco-bloodline-115-barrel 4aaee849158f (Primary Arms' gallery, BL-115-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.665), its width a line along the photo (110.20 px over columns 949 to 1139, 111.16 px over 1199 to 1629): each column scaled by that line (tools/trace.py's `calibrate: tube`); lengths by (u − 1099.5)/width, then by 1.0078, which puts the two end faces the published 11.5 in and the extension's 0.501 apart (overall_length)","method":"the flange's rear face (column 1918.0) to the collar's front face (column 762.7): the collar's rim fitted as an ellipse on the silhouette between the journal's radius and the collar's (seen from 13° off square, rms 0.001 in) (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"A gas block's rear face comes back to this shoulder, and Rosco places the dimple, and with it the port, from it (dimple_backspace). The three Bloodlines' own photos put it 6.91 (10.5), 6.94 (11.5), 6.93 (12.5) in ahead of the receiver: one carbine port."},"journal_front_x":{"label":"The gas block journal's front end (where the barrel steps down) ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":8.917,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/rosco-bloodline-115-barrel 4aaee849158f (Primary Arms' gallery, BL-115-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.665), its width a line along the photo (110.20 px over columns 949 to 1139, 111.16 px over 1199 to 1629): each column scaled by that line (tools/trace.py's `calibrate: tube`); lengths by (u − 1099.5)/width, then by 1.0078, which puts the two end faces the published 11.5 in and the extension's 0.501 apart (overall_length)","method":"the flange's rear face (column 1918.0) to where the height is midway between the journal's and the next section's (column 441.1), less its rim's arc there (0.023) (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"The journal is 1.97 long; ahead of it the barrel is 0.724 across to the muzzle shoulder. The step is a short cone, a tenth of an inch long."},"gas_port_x":{"label":"The gas port ahead of the extension's face","kind":"length","measurements":[{"id":"published","value":7.238,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.journal_rear_x} + {.dimple_backspace}","via":"harvest"},"note":"The shoulder as the photo has it, and the maker's figure from there."},{"id":"photo","value":7.258,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/rosco-bloodline-115-barrel 4aaee849158f (Primary Arms' gallery, BL-115-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.665), its width a line along the photo (110.20 px over columns 949 to 1139, 111.16 px over 1199 to 1629): each column scaled by that line (tools/trace.py's `calibrate: tube`); lengths by (u − 1099.5)/width, then by 1.0078, which puts the two end faces the published 11.5 in and the extension's 0.501 apart (overall_length)","method":"the flange's rear face (column 1918.0) to the dimple's bright dot of bare steel on the journal (centred column 708.0, row 673.0: 0.96 of the journal's radius off the axis): 0.338 ahead of the collar's front face as it shows, less 0.024 for its standing toward the lens by the rest of that radius, at a place seen from 13° off square (.cache/rosco/feat2.py)","via":"harvest"}}],"adopt":{"from":"published","reason":"The maker's own figure for where the dimple is from the shoulder; the photo's dot agrees with it within the photo's ±."},"note":"Rosco gives no distance from the receiver; its FAQ gives the dimple's from the journal's shoulder (dimple_backspace, .295), and the dimple is opposite the port. From the barrel's breech end this port is 7.71 in. The photo has the dimple as a bright dot on the journal, 0.314 ahead of the collar's front face: within 0.02 of where the FAQ puts it."},"shoulder_x":{"label":"The muzzle shoulder ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":10.432,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/rosco-bloodline-115-barrel 4aaee849158f (Primary Arms' gallery, BL-115-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.665), its width a line along the photo (110.20 px over columns 949 to 1139, 111.16 px over 1199 to 1629): each column scaled by that line (tools/trace.py's `calibrate: tube`); lengths by (u − 1099.5)/width, then by 1.0078, which puts the two end faces the published 11.5 in and the extension's 0.501 apart (overall_length)","method":"the flange's rear face (column 1918.0) to the muzzle shoulder's face (column 203.6): where the thread's edge meets the shoulder's silhouette and up to 0.035 under its rim, the silhouette is the rim's arc, an ellipse about the face at the obliquity its neighbours give (21°); 14 points agree on the face to 0.001 in. The ± is the obliquity's and the length's scale (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"Where the thread begins: a muzzle device or its washer seats here. The lens sees it from well off square: at mid-height the silhouette stands ahead of the face by its rim's arc."},"thread_length":{"label":"The muzzle thread's length","kind":"length","measurements":[{"id":"photo","value":0.597,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/rosco-bloodline-115-barrel 4aaee849158f (Primary Arms' gallery, BL-115-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.665), its width a line along the photo (110.20 px over columns 949 to 1139, 111.16 px over 1199 to 1629): each column scaled by that line (tools/trace.py's `calibrate: tube`); lengths by (u − 1099.5)/width, then by 1.0078, which puts the two end faces the published 11.5 in and the extension's 0.501 apart (overall_length)","method":"the shoulder's face (column 203.6) to the muzzle's face, behind its rim's arc (the tool's end_face: the tip at column 94, seen from 22° off square) (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"The Army barrel's is .63 (8448549); BCM's barrel read 0.50."},"index_pin_x":{"label":"The barrel indexing pin's axis behind the flange's rear face","kind":"length","measurements":[{"id":"photo","value":0.072,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/rosco-bloodline-115-barrel 4aaee849158f (Primary Arms' gallery, BL-115-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.665), its width a line along the photo (110.20 px over columns 949 to 1139, 111.16 px over 1199 to 1629): each column scaled by that line (tools/trace.py's `calibrate: tube`); lengths by (u − 1099.5)/width, then by 1.0078, which puts the two end faces the published 11.5 in and the extension's 0.501 apart (overall_length)","method":"the pin's rear edge on the lower silhouette (column 1941; the barrel lies with its pin down in the photo) to the flange's rear face (column 1918.0): 0.135, less half index_pin_d (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"The reference CAD set has the pin's axis 0.0765 behind the flange's rear face (0.2075 behind its front face)."},"index_pin_top":{"label":"The barrel indexing pin's top above the bore's axis","kind":"length","measurements":[{"id":"photo","value":0.582,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/rosco-bloodline-115-barrel 4aaee849158f (Primary Arms' gallery, BL-115-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.665), its width a line along the photo (110.20 px over columns 949 to 1139, 111.16 px over 1199 to 1629): each column scaled by that line (tools/trace.py's `calibrate: tube`)","method":"the pin's end on the lower silhouette, columns 1926 to 1941: its greatest distance from the axis (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"A little under the flange's radius, as on BCM's barrel (0.584)."},"outline_rear_face":{"label":"The extension's rear face in the traced outline's own frame (from the silhouette's rear tip)","kind":"length","measurements":[{"id":"photo","value":0.114,"unit":"in","pm":0.009,"source":{"type":"photo","photo":"references/rosco-bloodline-115-barrel 4aaee849158f (Primary Arms' gallery, BL-115-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"scale from rosco-bloodline-115-barrel.barrel_od = 0.665 in, the tube's own width column by column: 110.2 px over columns 949–1139, 111.2 px over columns 1199–1629; a line through them (rms 0.25 px) changes +1.5% from column 949 to 1629, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 165.9 px/in there. The axis is the tube's centre line (tilt +0.01°, rms 0.13 px). Lengths then scaled by 1.0078 so that the end faces are rosco-bloodline-115-barrel.overall_length = 12.001 in apart: at the tube's scale they read 11.908 (-0.8%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.104 in over radius 0.240 (rms 0.002), the rear end's rim sags 0.112 in over radius 0.494 (rms 0.002)","method":"the min end's face: the silhouette's tip at 0.000 less its rim's arc, 0.113 in of sag at radius 0.493941 (the end is seen from 12.9° off square; arc fitted over 113 rows, rms 0.002) of the traced outline (tools/trace.py); the extension's rear face in the outline's own frame (from its rear tip)","via":"harvest"}}]},"outline_front_face":{"label":"The muzzle's face in the traced outline's own frame (from the silhouette's rear tip)","kind":"length","measurements":[{"id":"photo","value":12.115,"unit":"in","pm":0.086,"source":{"type":"photo","photo":"references/rosco-bloodline-115-barrel 4aaee849158f (Primary Arms' gallery, BL-115-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"scale from rosco-bloodline-115-barrel.barrel_od = 0.665 in, the tube's own width column by column: 110.2 px over columns 949–1139, 111.2 px over columns 1199–1629; a line through them (rms 0.25 px) changes +1.5% from column 949 to 1629, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 165.9 px/in there. The axis is the tube's centre line (tilt +0.01°, rms 0.13 px). Lengths then scaled by 1.0078 so that the end faces are rosco-bloodline-115-barrel.overall_length = 12.001 in apart: at the tube's scale they read 11.908 (-0.8%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.104 in over radius 0.240 (rms 0.002), the rear end's rim sags 0.112 in over radius 0.494 (rms 0.002)","method":"the max end's face: the silhouette's tip at 12.220 less its rim's arc, 0.105 in of sag at radius 0.240293 (the end is seen from 23.6° off square; arc fitted over 121 rows, rms 0.002) of the traced outline (tools/trace.py); the muzzle's face in the outline's own frame (from its rear tip)","via":"harvest"}}]}}},{"subject":"rosco-bloodline-125-barrel","title":"Rosco Manufacturing Bloodline 12.5\" M4 5.56 NATO (BL-125-M4-556-7-C)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"rosco","value":21.79,"unit":"oz","pm":0.005,"stated":"Barrel Weight 21.79oz","source":{"type":"spec","publisher":"manufacturer","name":"Rosco Manufacturing, Bloodline 12.5\" M4 5.56 NATO (BL-125-M4-556-7-C), Description: the specification list","url":"https://www.roscomanufacturing.com/shop/barrels/blood-line-barrels/5-56-barrels/bloodline-12-5-5-56-nato/","retrieved":"2026-10-06","via":"harvest"}},{"id":"midwayusa","value":21.79,"unit":"oz","pm":0.005,"stated":"\"name\":\"Weight\",\"value\":\"21.79 Ounce\"","source":{"type":"spec","publisher":"retailer","name":"MidwayUSA, Rosco Manufacturing Bloodline AR-15 Barrel 5.56x45mm NATO 12.5\" M4 Contour 1:7\" Twist Black Nitride (product 407128, BL-125-M4-556-7-C), the page's product data","url":"https://www.midwayusa.com/product/1024526582?pid=407128","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"rosco","reason":"The maker's own figure; MidwayUSA repeats it (Primary Arms states none for this length)."},"note":"Rosco's three weights step 1.54 oz from the 10.5 to the 11.5 in barrel and 0.97 oz from there to this one. An inch of the section ahead of the journal (0.72 across, bored .219) is 1.7 oz of steel, and this barrel's model, turned from its own photo, is 6% over this figure as steel where its siblings' are 1 and 2% over theirs (their chambers still solid). Not explained: the published figure is kept, and the model isn't trimmed to it."},"length":{"label":"Barrel length as its maker states it","kind":"length","measurements":[{"id":"rosco","value":12.5,"unit":"in","pm":0.05,"stated":"Barrel Length 12.5″","source":{"type":"spec","publisher":"manufacturer","name":"Rosco Manufacturing, Bloodline 12.5\" M4 5.56 NATO (BL-125-M4-556-7-C), Description: the specification list","url":"https://www.roscomanufacturing.com/shop/barrels/blood-line-barrels/5-56-barrels/bloodline-12-5-5-56-nato/","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":12.5,"unit":"in","pm":0.05,"stated":"Barrel Length 12.5","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Rosco Manufacturing Bloodline 5.56 AR-15 Barrel - Carbine - Government - 12.5\" (BL-125-M4-556-7-C), Specifications","url":"https://www.primaryarms.com/rosco-manufacturing-bloodline-556-barrel-government-carbine-12.5","retrieved":"2026-10-06","via":"harvest"}},{"id":"midwayusa","value":12.5,"unit":"in","pm":0.05,"stated":"\"name\":\"Length\",\"value\":\"12.5 Inches\"","source":{"type":"spec","publisher":"retailer","name":"MidwayUSA, Rosco Manufacturing Bloodline AR-15 Barrel 5.56x45mm NATO 12.5\" M4 Contour 1:7\" Twist Black Nitride (product 407128, BL-125-M4-556-7-C), the page's product data","url":"https://www.midwayusa.com/product/1024526582?pid=407128","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"rosco","reason":"The maker's own; two sellers repeat it."},"note":"The nominal length. Rosco's page doesn't say between which points; the Army's barrel drawing (8448549) dimensions a barrel from its breech end, inside the extension, to its muzzle, and overall_length takes it so (as the catalog's other barrels do)."},"journal_od":{"label":"The gas block journal's diameter","kind":"length","measurements":[{"id":"rosco","value":0.75,"unit":"in","pm":0.0005,"stated":"Gas Block Size .750","source":{"type":"spec","publisher":"manufacturer","name":"Rosco Manufacturing, Bloodline 12.5\" M4 5.56 NATO (BL-125-M4-556-7-C), Description: the specification list","url":"https://www.roscomanufacturing.com/shop/barrels/blood-line-barrels/5-56-barrels/bloodline-12-5-5-56-nato/","retrieved":"2026-10-06","via":"harvest"}},{"id":"rosco-faq","value":0.75,"unit":"in","pm":0.0005,"stated":"We currently machine the “journal” or seating area to accommodate a .750 diameter gas block for all our barrels.","source":{"type":"spec","publisher":"manufacturer","name":"Rosco Manufacturing, FAQ's: What is the size of the Gas Block seating area for your barrels?","url":"https://www.roscomanufacturing.com/faqs/","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":0.75,"unit":"in","pm":0.0005,"stated":".750\" gas seat diameter","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Rosco Manufacturing Bloodline 5.56 AR-15 Barrel - Carbine - Government - 12.5\" (BL-125-M4-556-7-C), Features","url":"https://www.primaryarms.com/rosco-manufacturing-bloodline-556-barrel-government-carbine-12.5","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"rosco","reason":"The maker's own, on this barrel's page; its FAQ says the same of every barrel, and the seller repeats it."}},"dimple_backspace":{"label":"The gas block dimple's centre ahead of the journal's rear shoulder","kind":"length","measurements":[{"id":"rosco-faq","value":0.295,"unit":"in","pm":0.0005,"stated":"Yes we do, but we only machine one dimple that is perfectly centered and matched to a backspace of .295.","source":{"type":"spec","publisher":"manufacturer","name":"Rosco Manufacturing, FAQ's: Do you dimple your barrels for Gas Blocks?","url":"https://www.roscomanufacturing.com/faqs/","retrieved":"2026-10-06","via":"harvest"}}],"note":"Rosco's FAQ, of every barrel it makes: one dimple, under the journal, \"perfectly centered\": taken as centred on the gas port opposite it (a buyer on Primary Arms' page for the 11.5: \"Index pin is in line with the gas port\"; Primary Arms' photos have the port on the marked side and the dimple, bare steel, opposite it at the same place). The one published figure for where the port is: gas_port_x is the shoulder as read plus this."},"extension_behind_breech":{"label":"The barrel extension's rear end behind the barrel's breech end","kind":"length","measurements":[{"id":"model","value":0.501,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{std.ar15.barrel_extension_behind_breech}","via":"user"}}],"note":"The standard's: the reference CAD set's extension less the Army barrel's tenon (std.ar15.barrel_extension_behind_breech), the one figure the catalog's 5.56 barrels take their breech from. Primary Arms, for this number: \"nitride-finished M4 barrel extension\"."},"bore_d":{"label":"The bore's diameter (across the lands)","kind":"length","measurements":[{"id":"tdp","value":0.219,"unit":"in","pm":0.001,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.bore_d}","via":"user"}}],"note":"The Army barrel's, as BCM's barrel's ledger read it off the drawing (8448549 sheet 2: .219 DIA): a 5.56 NATO bore. Rosco publishes none."},"index_pin_d":{"label":"The barrel indexing pin's diameter","kind":"length","measurements":[{"id":"model","value":0.125,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.index_pin_d}","via":"user"}}],"note":"The reference CAD set's pin, as BCM's barrel's ledger read it: a mil-spec extension's."},"extension_mouth_d":{"label":"The barrel extension's rear opening, its diameter at the rear face","kind":"length","measurements":[{"id":"model","value":0.77,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_mouth_d}","via":"user"}}],"note":"The inside of a mil-spec M4 extension as the reference CAD set has it, read once for BCM's barrel, for how the rear end looks. Appearance only."},"extension_mouth_chamfer":{"label":"The rear opening's chamfer, its depth (at 45°)","kind":"length","measurements":[{"id":"model","value":0.045,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_mouth_chamfer}","via":"user"}}]},"extension_lug_bore_d":{"label":"The circle the extension's locking lugs leave between their tips","kind":"length","measurements":[{"id":"model","value":0.572,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_lug_bore_d}","via":"user"}}]},"extension_lug_depth":{"label":"The locking lugs' front faces, ahead of the extension's rear end","kind":"length","measurements":[{"id":"model","value":0.214,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_lug_depth}","via":"user"}}]},"extension_recess_d":{"label":"The recess ahead of the lugs, which the bolt's lugs turn in: its diameter","kind":"length","measurements":[{"id":"model","value":0.83,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_recess_d}","via":"user"}}]},"extension_recess_depth":{"label":"The recess's front end, ahead of the extension's rear end","kind":"length","measurements":[{"id":"model","value":0.595,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_recess_depth}","via":"user"}}]},"thread_major_d":{"label":"The muzzle thread's major diameter (its crests)","kind":"length","measurements":[{"id":"tdp","value":0.4957,"unit":"in","pm":0.0033,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.thread_major_d}","via":"user"}}],"note":"The Army barrel's 1/2-28 thread (8448549 sheet 1, as BCM's barrel's ledger read it), for the 1/2 x 28 Rosco states: what the model's thread is drawn at."},"thread_minor_d":{"label":"The muzzle thread's minor diameter (its roots)","kind":"length","measurements":[{"id":"tdp","value":0.4551,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.thread_minor_d}","via":"user"}}]},"thread_pitch":{"label":"The muzzle thread's pitch","kind":"length","measurements":[{"id":"rosco","value":0.03571,"unit":"in","pm":0.00005,"stated":"Barrel Thread 1/2 x 28","source":{"type":"spec","publisher":"manufacturer","name":"Rosco Manufacturing, Bloodline 12.5\" M4 5.56 NATO (BL-125-M4-556-7-C), Description: the specification list","url":"https://www.roscomanufacturing.com/shop/barrels/blood-line-barrels/5-56-barrels/bloodline-12-5-5-56-nato/","retrieved":"2026-10-06","via":"harvest"}},{"id":"rosco-faq","value":0.03571,"unit":"in","pm":0.00005,"stated":"5.56 are threaded to ½ X 28","source":{"type":"spec","publisher":"manufacturer","name":"Rosco Manufacturing, FAQ's: What thread pattern do you use for your barrels?","url":"https://www.roscomanufacturing.com/faqs/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"rosco","reason":"This barrel's own page; the FAQ says the same of every 5.56 barrel."},"note":"28 threads to the inch, by the maker's statement."},"crown_angle":{"label":"The muzzle crown's angle (its face's cone, from square to the bore)","kind":"angle","measurements":[{"id":"rosco","value":11,"unit":"deg","pm":0.5,"stated":"Barrel Crown 11 Degree","source":{"type":"spec","publisher":"manufacturer","name":"Rosco Manufacturing, Bloodline 12.5\" M4 5.56 NATO (BL-125-M4-556-7-C), Description: the specification list","url":"https://www.roscomanufacturing.com/shop/barrels/blood-line-barrels/5-56-barrels/bloodline-12-5-5-56-nato/","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":11,"unit":"deg","pm":0.5,"stated":"Threaded 1/2x28, 11-degree crown","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Rosco Manufacturing Bloodline 5.56 AR-15 Barrel - Carbine - Government - 12.5\" (BL-125-M4-556-7-C), Features","url":"https://www.primaryarms.com/rosco-manufacturing-bloodline-556-barrel-government-carbine-12.5","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"rosco","reason":"The maker's own; the seller repeats it."},"note":"Rosco's FAQ: \"For the Bloodline barrels we use a 11 degree “service” crown.\" How far out across the muzzle's face it reaches isn't published."},"gas_port_d":{"label":"The gas port's diameter","kind":"length","measurements":[{"id":"buyer","value":0.073,"unit":"in","pm":0.01,"stated":".073 gas port Concentric threads Index pin is in line with the gas port","source":{"type":"spec","publisher":"review","name":"A buyer's review on Primary Arms' page for the 11.5 in barrel, BL-115-M4-556-7-C (2021-11-02)","url":"https://www.primaryarms.com/rosco-manufacturing-bloodline-556-barrel-government-carbine-11.5","retrieved":"2026-10-06","via":"harvest"}}],"note":"Rosco withholds it (FAQ: \"Unfortunately, we cannot disclose more seeing as these measurements are proprietary production information.\"), and says it is sized to each barrel. The one figure on file is a buyer's for the 11.5 in barrel, in a review on Primary Arms' page for that one, no instrument named: this 12.5 in barrel's own port isn't known, and the model cuts a hole of that size so that there is one."},"barrel_od":{"label":"The straight section between the chamber and the collar, its diameter","kind":"length","measurements":[{"id":"photo","value":0.666,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/rosco-bloodline-125-barrel 0f416d824f87 (Primary Arms' gallery, BL-125-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"its gas block journal's diameter, 114.61 px (the median over the journal's columns, the silhouette at grey 235), as the published .750 (journal_od)","method":"the straight section's width as a line along the photo, fitted over columns 1069 to 1339 (101.69 px) and 1399 to 1653 (101.53 px), rms 0.16 px, carried on to the journal's columns: 101.71 px there, 0.8875 of the journal's (tools/trace.py fit_tube; .cache/rosco/pa.py) (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"The scale of the traced outline: this section, a cylinder, is what each column of the photo is scaled by (`calibrate: tube`). Its own diameter is read against the journal's published .750 on the same photo. That it is a cylinder is taken, and checked by what it predicts at the two ends of the barrel: the extension's body 1.010 (the Army's limit .999), the flange 1.186 (the reference CAD set's 1.170), the thread's crests 0.486 (the Army's 1/2-28: .4924 to .4989). The three Bloodlines' photos, each read on its own, give this section 0.662 (10.5), 0.665 (11.5), 0.666 (12.5)."},"overall_length":{"label":"End to end, the extension's rear to the muzzle","kind":"length","measurements":[{"id":"photo","value":13,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/rosco-bloodline-125-barrel 0f416d824f87 (Primary Arms' gallery, BL-125-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.666), its width a line along the photo (101.69 px over columns 1069 to 1339, 101.53 px over 1399 to 1653): each column scaled by that line (tools/trace.py's `calibrate: tube`)","method":"its two end faces, each behind its rim's arc, at the tube's own scale with the lens's axis taken at the image's middle (tools/trace.py: read 13.005) (.cache/rosco/feat2.py)","via":"harvest"}},{"id":"published","value":13.001,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{.length} + {.extension_behind_breech}","via":"harvest"}}],"adopt":{"from":"published","reason":"Lengths at the published length, as the catalog's other barrels have them, so that barrels of different makers stand on one breech; the photo's own scale agrees with it within what the photo leaves open."},"note":"The published length from the barrel's breech end, and the extension's half inch behind that. The photo at its own scale (the journal's .750, through the straight section) reads +0.0% of it between its end faces: within what the end faces, the yaw's cosine and the lens's place leave open. The outline's lengths are set to the published figure, as the catalog's other barrels' are."},"extension_od":{"label":"The barrel extension's body, its diameter (what goes into the receiver)","kind":"length","measurements":[{"id":"tdp","value":0.999,"unit":"in","pm":0.001,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.extension_od}","via":"user"},"note":"An upper limit: it goes into the receiver's 1.000 bore."},{"id":"photo","value":1.01,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/rosco-bloodline-125-barrel 0f416d824f87 (Primary Arms' gallery, BL-125-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.666), its width a line along the photo (101.69 px over columns 1069 to 1339, 101.53 px over 1399 to 1653): each column scaled by that line (tools/trace.py's `calibrate: tube`)","method":"the extension's body, the median of its height from a quarter to three quarters of an inch ahead of its rear face (.cache/rosco/feat2.py)","via":"harvest"}}],"adopt":{"from":"tdp","reason":"An extension over 1.000 doesn't go into a receiver: the photo reads its breech end 1% large, and the drawing's limit is what an M4 extension is made to."},"note":"The photo reads this barrel's breech end 1% large: over the Army drawing's limit for an extension (8448548, as BCM's barrel's ledger read it: not to exceed .9990), as its flange is over the reference CAD set's (1.186 against 1.170) and its chamber section over its two siblings' (0.99 against 0.98). The straight section's own width doesn't show a yaw in this photo, but the breech end is nearer the lens all the same; the model takes the drawing's limit here and brings the outline behind the straight section's middle down in proportion."},"flange_od":{"label":"The barrel extension's flange, its diameter","kind":"length","measurements":[{"id":"photo","value":1.186,"unit":"in","pm":0.007,"source":{"type":"photo","photo":"references/rosco-bloodline-125-barrel 0f416d824f87 (Primary Arms' gallery, BL-125-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.666), its width a line along the photo (101.69 px over columns 1069 to 1339, 101.53 px over 1399 to 1653): each column scaled by that line (tools/trace.py's `calibrate: tube`)","method":"the flange's greatest height, on the lower of the two edges at each column (the pin, where it shows, is on one) (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"The reference CAD set's flange is 1.170 across: this photo reads its breech end 1% large (see extension_od), and the model brings it down with the rest of that end."},"chamber_od":{"label":"The chamber section ahead of the flange, its diameter","kind":"length","measurements":[{"id":"photo","value":0.992,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/rosco-bloodline-125-barrel 0f416d824f87 (Primary Arms' gallery, BL-125-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.666), its width a line along the photo (101.69 px over columns 1069 to 1339, 101.53 px over 1399 to 1653): each column scaled by that line (tools/trace.py's `calibrate: tube`)","method":"the median of its height over a third of an inch, a quarter inch ahead of the flange (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"The cylinder ahead of the flange, before the cone down to the straight section."},"collar_od":{"label":"The collar behind the gas block journal, its diameter","kind":"length","measurements":[{"id":"photo","value":0.857,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/rosco-bloodline-125-barrel 0f416d824f87 (Primary Arms' gallery, BL-125-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.666), its width a line along the photo (101.69 px over columns 1069 to 1339, 101.53 px over 1399 to 1653): each column scaled by that line (tools/trace.py's `calibrate: tube`)","method":"the median of its height over its cylinder (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"A gas block's rear face comes back to its front face. A curved ramp leads up to it from the straight section."},"muzzle_od":{"label":"The diameter behind the muzzle thread","kind":"length","measurements":[{"id":"photo","value":0.72,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/rosco-bloodline-125-barrel 0f416d824f87 (Primary Arms' gallery, BL-125-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.666), its width a line along the photo (101.69 px over columns 1069 to 1339, 101.53 px over 1399 to 1653): each column scaled by that line (tools/trace.py's `calibrate: tube`)","method":"the median of its height from a third to an eighth of an inch behind the muzzle shoulder (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"The section between the journal's front end and the muzzle shoulder: a little under the journal's .750, so a gas block slides on over it."},"extension_rear_x":{"label":"The barrel extension's rear end, from the flange's rear face (negative: inside the receiver)","kind":"length","measurements":[{"id":"photo","value":-1.02,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/rosco-bloodline-125-barrel 0f416d824f87 (Primary Arms' gallery, BL-125-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.666), its width a line along the photo (101.69 px over columns 1069 to 1339, 101.53 px over 1399 to 1653): each column scaled by that line (tools/trace.py's `calibrate: tube`); lengths by (u − 1099.5)/width, then by 0.9997, which puts the two end faces the published 12.5 in and the extension's 0.501 apart (overall_length)","method":"the rear end's face, behind its rim's arc (the tool's end_face: the silhouette's tip at column 2105, the face 0.103 in ahead of it: that end is seen from 12° off square), to the flange's rear face (column 1934.0: the flange's rim fitted as an ellipse between the body's radius and its own, seen from 15° off square) (.cache/rosco/feat2.py)","via":"harvest"}},{"id":"model","value":-0.99,"unit":"in","pm":0.007,"source":{"type":"derived","expr":"{std.ar15.barrel_extension_flange_thickness} - {std.ar15.barrel_extension_length}","via":"user"},"note":"A mil-spec extension as the reference CAD set has it: the standard's, not this barrel's."}],"adopt":{"from":"photo","reason":"This barrel's own photo, which the outline is cut and placed by; it stands 0.03 from the standard extension's, and the note says why it is doubted."},"note":"The photo reads this extension 0.03 longer behind its flange than the reference CAD set's (0.990) and 0.04 to 0.05 longer than its two siblings' photos read the same M4 extension (0.972 and 0.980). The rear rim's arc is what is in doubt: the tool reads that end as seen from 12° off square where the flange an inch ahead of it is seen from 15°, and the feed ramps' cuts take the top of that rim out of the silhouette; with the flange's angle the face would be 0.03 further forward. The outline is cut and placed by the photo's reading all the same (the whole of it hangs together by that face), and the difference, hidden inside the receiver, stays visible here: with it the muzzle stands 0.05 in short of a whole inch ahead of the 11.5 in barrel's."},"flange_front_x":{"label":"The extension flange's front face, ahead of its rear face (the flange's thickness)","kind":"length","measurements":[{"id":"photo","value":0.081,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/rosco-bloodline-125-barrel 0f416d824f87 (Primary Arms' gallery, BL-125-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.666), its width a line along the photo (101.69 px over columns 1069 to 1339, 101.53 px over 1399 to 1653): each column scaled by that line (tools/trace.py's `calibrate: tube`); lengths by (u − 1099.5)/width, then by 0.9997, which puts the two end faces the published 12.5 in and the extension's 0.501 apart (overall_length)","method":"the flange's rear face (column 1934.0) to its front face (column 1921.7), each where its rim's ellipse, fitted on the silhouette between the neighbour's radius and the flange's, comes to the flange's full radius (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"The reference CAD set's flange is 0.131 thick; BCM's barrel read 0.095. At mid-height the silhouette is twice this wide: each face's rim is an ellipse, the rear one's near half standing behind its face and the front one's far half ahead of it."},"taper_rear_x":{"label":"Where the cone ahead of the chamber section begins, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":0.791,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/rosco-bloodline-125-barrel 0f416d824f87 (Primary Arms' gallery, BL-125-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.666), its width a line along the photo (101.69 px over columns 1069 to 1339, 101.53 px over 1399 to 1653): each column scaled by that line (tools/trace.py's `calibrate: tube`); lengths by (u − 1099.5)/width, then by 0.9997, which puts the two end faces the published 12.5 in and the extension's 0.501 apart (overall_length)","method":"the flange's rear face (column 1934.0) to where the line through the cone's middle (between a fifth and four fifths of its drop) meets the chamber section's diameter (column 1813.4) (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"The cone is straight: a line through its middle meets the chamber section's cylinder here."},"taper_front_x":{"label":"Where that cone ends and the straight section begins, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":1.649,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/rosco-bloodline-125-barrel 0f416d824f87 (Primary Arms' gallery, BL-125-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.666), its width a line along the photo (101.69 px over columns 1069 to 1339, 101.53 px over 1399 to 1653): each column scaled by that line (tools/trace.py's `calibrate: tube`); lengths by (u − 1099.5)/width, then by 0.9997, which puts the two end faces the published 12.5 in and the extension's 0.501 apart (overall_length)","method":"the flange's rear face (column 1934.0) to where the same line meets the straight section's diameter (column 1682.8) (.cache/rosco/feat2.py)","via":"harvest"}}]},"ramp_rear_x":{"label":"Where the ramp up to the collar leaves the straight section, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":5.932,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/rosco-bloodline-125-barrel 0f416d824f87 (Primary Arms' gallery, BL-125-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.666), its width a line along the photo (101.69 px over columns 1069 to 1339, 101.53 px over 1399 to 1653): each column scaled by that line (tools/trace.py's `calibrate: tube`); lengths by (u − 1099.5)/width, then by 0.9997, which puts the two end faces the published 12.5 in and the extension's 0.501 apart (overall_length)","method":"the flange's rear face (column 1934.0) to where the height first stands 0.006 over the straight section's (column 1029.0) (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"The ramp is curved: shallow where it leaves the straight section, steeper into the collar. The model follows the outline along it."},"collar_rear_x":{"label":"Where the ramp reaches the collar's cylinder, ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":6.313,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/rosco-bloodline-125-barrel 0f416d824f87 (Primary Arms' gallery, BL-125-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.666), its width a line along the photo (101.69 px over columns 1069 to 1339, 101.53 px over 1399 to 1653): each column scaled by that line (tools/trace.py's `calibrate: tube`); lengths by (u − 1099.5)/width, then by 0.9997, which puts the two end faces the published 12.5 in and the extension's 0.501 apart (overall_length)","method":"the flange's rear face (column 1934.0) to where the height comes within 0.006 of the collar's (column 970.9) (.cache/rosco/feat2.py)","via":"harvest"}}]},"journal_rear_x":{"label":"The gas block journal's rear shoulder (the collar's front face) ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":6.932,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/rosco-bloodline-125-barrel 0f416d824f87 (Primary Arms' gallery, BL-125-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.666), its width a line along the photo (101.69 px over columns 1069 to 1339, 101.53 px over 1399 to 1653): each column scaled by that line (tools/trace.py's `calibrate: tube`); lengths by (u − 1099.5)/width, then by 0.9997, which puts the two end faces the published 12.5 in and the extension's 0.501 apart (overall_length)","method":"the flange's rear face (column 1934.0) to the collar's front face (column 876.3): the collar's rim fitted as an ellipse on the silhouette between the journal's radius and the collar's (seen from 13° off square, rms 0.001 in) (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"A gas block's rear face comes back to this shoulder, and Rosco places the dimple, and with it the port, from it (dimple_backspace). The three Bloodlines' own photos put it 6.91 (10.5), 6.94 (11.5), 6.93 (12.5) in ahead of the receiver: one carbine port."},"journal_front_x":{"label":"The gas block journal's front end (where the barrel steps down) ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":8.928,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/rosco-bloodline-125-barrel 0f416d824f87 (Primary Arms' gallery, BL-125-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.666), its width a line along the photo (101.69 px over columns 1069 to 1339, 101.53 px over 1399 to 1653): each column scaled by that line (tools/trace.py's `calibrate: tube`); lengths by (u − 1099.5)/width, then by 0.9997, which puts the two end faces the published 12.5 in and the extension's 0.501 apart (overall_length)","method":"the flange's rear face (column 1934.0) to where the height is midway between the journal's and the next section's (column 568.2), less its rim's arc there (0.018) (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"The journal is 2.00 long; ahead of it the barrel is 0.720 across to the muzzle shoulder. The step is a short cone, a tenth of an inch long."},"gas_port_x":{"label":"The gas port ahead of the extension's face","kind":"length","measurements":[{"id":"published","value":7.227,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.journal_rear_x} + {.dimple_backspace}","via":"harvest"},"note":"The shoulder as the photo has it, and the maker's figure from there."}],"note":"Rosco gives no distance from the receiver; its FAQ gives the dimple's from the journal's shoulder (dimple_backspace, .295), and the dimple is opposite the port. From the barrel's breech end this port is 7.75 in. This photo doesn't show the dimple (it is turned away from the lens); Primary Arms' other views of this barrel show the port and the dimple on the journal just ahead of the collar, and aren't measured."},"shoulder_x":{"label":"The muzzle shoulder ahead of the extension's face","kind":"length","measurements":[{"id":"photo","value":11.389,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/rosco-bloodline-125-barrel 0f416d824f87 (Primary Arms' gallery, BL-125-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.666), its width a line along the photo (101.69 px over columns 1069 to 1339, 101.53 px over 1399 to 1653): each column scaled by that line (tools/trace.py's `calibrate: tube`); lengths by (u − 1099.5)/width, then by 0.9997, which puts the two end faces the published 12.5 in and the extension's 0.501 apart (overall_length)","method":"the flange's rear face (column 1934.0) to the muzzle shoulder's face (column 194.1): where the thread's edge meets the shoulder's silhouette and up to 0.035 under its rim, the silhouette is the rim's arc, an ellipse about the face at the obliquity its neighbours give (14°); 10 points agree on the face to 0.002 in. The ± is the obliquity's and the length's scale (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"Where the thread begins: a muzzle device or its washer seats here. The lens sees it from well off square: at mid-height the silhouette stands ahead of the face by its rim's arc."},"thread_length":{"label":"The muzzle thread's length","kind":"length","measurements":[{"id":"photo","value":0.592,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/rosco-bloodline-125-barrel 0f416d824f87 (Primary Arms' gallery, BL-125-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.666), its width a line along the photo (101.69 px over columns 1069 to 1339, 101.53 px over 1399 to 1653): each column scaled by that line (tools/trace.py's `calibrate: tube`); lengths by (u − 1099.5)/width, then by 0.9997, which puts the two end faces the published 12.5 in and the extension's 0.501 apart (overall_length)","method":"the shoulder's face (column 194.1) to the muzzle's face, behind its rim's arc (the tool's end_face: the tip at column 94, seen from 14° off square) (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"The Army barrel's is .63 (8448549); BCM's barrel read 0.50."},"index_pin_x":{"label":"The barrel indexing pin's axis behind the flange's rear face","kind":"length","measurements":[{"id":"photo","value":0.095,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/rosco-bloodline-125-barrel 0f416d824f87 (Primary Arms' gallery, BL-125-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.666), its width a line along the photo (101.69 px over columns 1069 to 1339, 101.53 px over 1399 to 1653): each column scaled by that line (tools/trace.py's `calibrate: tube`); lengths by (u − 1099.5)/width, then by 0.9997, which puts the two end faces the published 12.5 in and the extension's 0.501 apart (overall_length)","method":"the pin's rear edge on the lower silhouette (column 1958; the barrel lies with its pin down in the photo) to the flange's rear face (column 1934.0): 0.157, less half index_pin_d (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"The reference CAD set has the pin's axis 0.0765 behind the flange's rear face (0.2075 behind its front face)."},"index_pin_top":{"label":"The barrel indexing pin's top above the bore's axis","kind":"length","measurements":[{"id":"photo","value":0.594,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/rosco-bloodline-125-barrel 0f416d824f87 (Primary Arms' gallery, BL-125-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"the straight section between the chamber and the collar as barrel_od (0.666), its width a line along the photo (101.69 px over columns 1069 to 1339, 101.53 px over 1399 to 1653): each column scaled by that line (tools/trace.py's `calibrate: tube`)","method":"the pin's end on the lower silhouette, columns 1943 to 1958: its greatest distance from the axis (.cache/rosco/feat2.py)","via":"harvest"}}],"note":"A little under the flange's radius, as on BCM's barrel (0.584)."},"outline_rear_face":{"label":"The extension's rear face in the traced outline's own frame (from the silhouette's rear tip)","kind":"length","measurements":[{"id":"photo","value":0.103,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/rosco-bloodline-125-barrel 0f416d824f87 (Primary Arms' gallery, BL-125-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"scale from rosco-bloodline-125-barrel.barrel_od = 0.666 in, the tube's own width column by column: 101.7 px over columns 1069–1339, 101.5 px over columns 1399–1653; a line through them (rms 0.16 px) changes -0.1% from column 1069 to 1653, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 152.6 px/in there. The axis is the tube's centre line (tilt -0.01°, rms 0.07 px). Lengths then scaled by 0.9997 so that the end faces are rosco-bloodline-125-barrel.overall_length = 13.001 in apart: at the tube's scale they read 13.005 (+0.0%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.077 in over radius 0.236 (rms 0.002), the rear end's rim sags 0.103 in over radius 0.501 (rms 0.003)","method":"the min end's face: the silhouette's tip at -0.000 less its rim's arc, 0.103 in of sag at radius 0.501251 (the end is seen from 11.6° off square; arc fitted over 119 rows, rms 0.003) of the traced outline (tools/trace.py); the extension's rear face in the outline's own frame (from its rear tip)","via":"harvest"}}]},"outline_front_face":{"label":"The muzzle's face in the traced outline's own frame (from the silhouette's rear tip)","kind":"length","measurements":[{"id":"photo","value":13.104,"unit":"in","pm":0.091,"source":{"type":"photo","photo":"references/rosco-bloodline-125-barrel 0f416d824f87 (Primary Arms' gallery, BL-125-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","scaleRef":"scale from rosco-bloodline-125-barrel.barrel_od = 0.666 in, the tube's own width column by column: 101.7 px over columns 1069–1339, 101.5 px over columns 1399–1653; a line through them (rms 0.16 px) changes -0.1% from column 1069 to 1653, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 152.6 px/in there. The axis is the tube's centre line (tilt -0.01°, rms 0.07 px). Lengths then scaled by 0.9997 so that the end faces are rosco-bloodline-125-barrel.overall_length = 13.001 in apart: at the tube's scale they read 13.005 (+0.0%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.077 in over radius 0.236 (rms 0.002), the rear end's rim sags 0.103 in over radius 0.501 (rms 0.003)","method":"the max end's face: the silhouette's tip at 13.181 less its rim's arc, 0.077 in of sag at radius 0.236069 (the end is seen from 18.1° off square; arc fitted over 118 rows, rms 0.002) of the traced outline (tools/trace.py); the muzzle's face in the outline's own frame (from its rear tip)","via":"harvest"}}]}}},{"subject":"sb-tactical-sba3","title":"SB Tactical SBA3® AR Adjustable Pistol Stabilizing Brace®","dimensions":{"length":{"label":"Overall length (the brace alone, its housing's front face to its end cap's rear face)","kind":"length","measurements":[{"id":"photo-extended","value":6.38,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/sb-tactical-sba3 94c73cb7eed3 (SB Tactical: SBA_3_Black_Left_Extended_web.jpg, an Aero M4E1 pistol with the brace at full extension, its true left side, in colour, 2500 x 2500)","scaleRef":"the lower's two pins, std.ar15 spacing 6.375 in: the pivot pin's head centred at (1062.5, 1138), the takedown pin's at (1561.5, 1139.5), on 6x and 8x gridded crops: 499 px, 78.27 px/in; level to 0.2 degrees","method":"the housing's front face at column 1901.5 (row 1030, above the tube's top edge) and the end cap's rear face at 2401 (rows 1050 to 1090), luminance under 120: 499.5 px. ± for the pins' centres (1.5 px each), the two faces (1.5 px each) and the brace's near side standing about 0.45 in nearer the lens than the pins' heads","via":"harvest"}},{"id":"photo-collapsed","value":6.27,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/sb-tactical-sba3 32ece668ff25 (SB Tactical: SBA_3_Black_Left_ghost_web.jpg, the same pistol with the brace collapsed, the rifle ghosted grey and the brace in colour, its true left side, 2500 x 2500)","scaleRef":"the lower's two pins, std.ar15 spacing 6.375 in: the pivot pin's head centred at (1144, 1187), the takedown pin's at (1711.5, 1188), on 8x gridded crops: 567.5 px, 89.02 px/in","method":"the brace's dark pixels (luminance under 90, which leaves the ghosted rifle out): the housing's front face at column 1870 (rows 1100 to 1120), the end cap's rear face at 2428: 558 px. ± as the extended picture's; the ghosting makes the pins' rims fainter","via":"harvest"}}],"adopt":{"from":"photo-extended","reason":"The extended picture is a photograph in colour whose pin frame lands two other standard figures (the receiver's rear face and the tube's width); the ghosted one's pins are faint. The two agree within their ±; the collapsed one is kept beside it."},"note":"No page gives the brace's own length (the published 6.75 in is length_collapsed: what it adds behind the end plate). Read on the maker's two pictures of it on an Aero M4E1 pistol, each framed by the lower's two pins. The two readings are 0.11 in apart, 1.7%: within their ± together. The extended picture's frame checks on two standard figures it wasn't set by (the receiver's rear face 1.13 in behind the pin for the drawing's 1.125; the exposed tube's silhouette 1.13 in across for 1.148, a black tube reading 2% thin as it does), the ghosted one's on the rear face only (1.11)."},"height":{"label":"Height (the strap loop's top to the strap's foot under the cuff)","kind":"length","measurements":[{"id":"photo-extended","value":5.76,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/sb-tactical-sba3 94c73cb7eed3 (SB Tactical: SBA_3_Black_Left_Extended_web.jpg, an Aero M4E1 pistol with the brace at full extension, its true left side, in colour, 2500 x 2500)","scaleRef":"the lower's two pins, std.ar15 spacing 6.375 in: the pivot pin's head centred at (1062.5, 1138), the takedown pin's at (1561.5, 1139.5), on 6x and 8x gridded crops: 499 px, 78.27 px/in; level to 0.2 degrees","method":"the housing's front face at column 1901.5 (row 1030, above the tube's top edge) and the end cap's rear face at 2401 (rows 1050 to 1090), luminance under 120: 499.5 px. ± for the pins' centres (1.5 px each), the two faces (1.5 px each) and the brace's near side standing about 0.45 in nearer the lens than the pins' heads","via":"harvest"},"note":"The loop's top at row 995.5 (columns 2300 to 2380), the strap's foot at 1446 (columns 2280 to 2360): 450.5 px."},{"id":"photo-collapsed","value":5.71,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/sb-tactical-sba3 32ece668ff25 (SB Tactical: SBA_3_Black_Left_ghost_web.jpg, the same pistol with the brace collapsed, the rifle ghosted grey and the brace in colour, its true left side, 2500 x 2500)","scaleRef":"the lower's two pins, std.ar15 spacing 6.375 in: the pivot pin's head centred at (1144, 1187), the takedown pin's at (1711.5, 1188), on 8x gridded crops: 567.5 px, 89.02 px/in","method":"the brace's dark pixels (luminance under 90, which leaves the ghosted rifle out): the housing's front face at column 1870 (rows 1100 to 1120), the end cap's rear face at 2428: 558 px. ± as the extended picture's; the ghosting makes the pins' rims fainter","via":"harvest"},"note":"The loop's top at row 1025.5, the strap's foot at 1533.5: 508 px."}],"adopt":{"from":"photo-extended","reason":"As the length: the frame that lands two standard figures. The collapsed picture agrees within the ±."},"note":"No page states one. Read on the same two pictures as the length, in the same frames. The silhouette's top is the top of the loop the strap runs through; its foot is the strap where it wraps under the cuff."},"width":{"label":"Width (max)","kind":"length","measurements":[{"id":"sb-sheet","value":1.8,"unit":"in","stated":"Width (max): 1.8\"","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBA3 Pistol Stabilizing Brace specification sheet (REV DEC 2021; the product page's 'SBA3 Specification Sheet')","url":"https://www.sb-tactical.com/wp-content/uploads/SBA3_X_12821-1.pdf","retrieved":"2026-10-18","via":"harvest"}},{"id":"sb-page","value":2,"unit":"in","stated":"Width: Approximately 2″","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBA3 product page (the description)","url":"https://www.sb-tactical.com/product/sba3/","retrieved":"2026-10-18","via":"harvest"}},{"id":"sb-spec-tab","value":2,"unit":"in","stated":"Max Width Approximately 2\"","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBA3 product page (the Specifications tab)","url":"https://www.sb-tactical.com/product/sba3/","retrieved":"2026-10-18","via":"harvest"}},{"id":"primary-arms","value":1.8,"unit":"in","stated":"Width: 1.8\"","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, SB Tactical SBA3 AR Pistol Brace (SKU: SBA3X-01-SB)","url":"https://www.primaryarms.com/sb-tactical-sba3-ar-pistol-stabilizing-brace-black-no-buffer-tube","retrieved":"2026-10-18","via":"harvest"}},{"id":"midwest","value":1.8,"unit":"in","stated":"Width(max) 1.8\"","source":{"type":"spec","publisher":"retailer","name":"Midwest Gun Works, SB Tactical AR-15 SBA3 Brace (SBA3-XX)","url":"https://www.midwestgunworks.com/page/mgwi/prod/sba3-xx","retrieved":"2026-10-18","via":"harvest"}},{"id":"photo-rear","value":1.84,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/sb-tactical-sba3 7c418fd9274e (SB Tactical: SBA3-rear-product_image.jpg, the brace straight from the rear, 2000 x 1500)","scaleRef":"the height (5.76 in) over the silhouette's 1065 rows (212 to 1277): 184.9 px/in","method":"the end cap's block across at row 420, inside the strap each side (columns 832 to 1172), on a 1.8x gridded crop","via":"harvest"}}],"adopt":{"from":"sb-sheet","reason":"The maker's sheet names it the maximum; two sellers repeat it and the rear view reads the body 1.84 across, inside the ±. The page's 2 is 'approximately' and is the body with its strap round it."},"note":"The maker gives two: its sheet's \"Width (max): 1.8\"\" (which two sellers repeat) and its page's \"Approximately 2″\". The maker's straight view from the rear, scaled by the height, has the end cap's block 1.84 in across (340 px at 184.9 px/in, row 420) and the strap round it 2.0 in: the sheet's figure is the body's, the page's the body with its strap."},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"sb-page","value":6.75,"unit":"oz","stated":"Weight: Approximately 6.75 oz","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBA3 product page (the description)","url":"https://www.sb-tactical.com/product/sba3/","retrieved":"2026-10-18","via":"harvest"}},{"id":"sb-spec-tab","value":7,"unit":"oz","stated":"Weight 7 oz","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBA3 product page (the Specifications tab)","url":"https://www.sb-tactical.com/product/sba3/","retrieved":"2026-10-18","via":"harvest"}},{"id":"sb-sheet","value":7.25,"unit":"oz","stated":"Weight: 7.25oz","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBA3 Pistol Stabilizing Brace specification sheet (REV DEC 2021; the product page's 'SBA3 Specification Sheet')","url":"https://www.sb-tactical.com/wp-content/uploads/SBA3_X_12821-1.pdf","retrieved":"2026-10-18","via":"harvest"}},{"id":"midwest","value":6.75,"unit":"oz","stated":"Weighs 6.75 oz","source":{"type":"spec","publisher":"retailer","name":"Midwest Gun Works, SB Tactical AR-15 SBA3 Brace (SBA3-XX)","url":"https://www.midwestgunworks.com/page/mgwi/prod/sba3-xx","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"sb-page","reason":"The maker's current page, in its description and in the last line of its spec tab; a seller repeats it. The tab's 7 oz and the 2021 sheet's 7.25 are kept beside it, not averaged."},"note":"Three figures on the maker's own pages: 6.75 oz (the page's description, and the last line of its spec tab), 7 oz (the spec tab's first line) and 7.25 oz (the 2021 sheet). A seller repeats 6.75."},"tube_axis_below_top":{"label":"Tube axis below the brace's top (the strap loop's top)","kind":"length","measurements":[{"id":"photo-extended","value":0.95,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sb-tactical-sba3 94c73cb7eed3 (SB Tactical: SBA_3_Black_Left_Extended_web.jpg, an Aero M4E1 pistol with the brace at full extension, its true left side, in colour, 2500 x 2500)","scaleRef":"the lower's two pins, std.ar15 spacing 6.375 in: the pivot pin's head centred at (1062.5, 1138), the takedown pin's at (1561.5, 1139.5), on 6x and 8x gridded crops: 499 px, 78.27 px/in; level to 0.2 degrees","method":"the housing's front face at column 1901.5 (row 1030, above the tube's top edge) and the end cap's rear face at 2401 (rows 1050 to 1090), luminance under 120: 499.5 px. ± for the pins' centres (1.5 px each), the two faces (1.5 px each) and the brace's near side standing about 0.45 in nearer the lens than the pins' heads","via":"harvest"},"note":"The axis at row 1070.1 (the pins' row 1138.75 less 0.8775 in), the loop's top at 995.5: 74.6 px."},{"id":"photo-collapsed","value":0.94,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sb-tactical-sba3 32ece668ff25 (SB Tactical: SBA_3_Black_Left_ghost_web.jpg, the same pistol with the brace collapsed, the rifle ghosted grey and the brace in colour, its true left side, 2500 x 2500)","scaleRef":"the lower's two pins, std.ar15 spacing 6.375 in: the pivot pin's head centred at (1144, 1187), the takedown pin's at (1711.5, 1188), on 8x gridded crops: 567.5 px, 89.02 px/in","method":"the brace's dark pixels (luminance under 90, which leaves the ghosted rifle out): the housing's front face at column 1870 (rows 1100 to 1120), the end cap's rear face at 2428: 558 px. ± as the extended picture's; the ghosting makes the pins' rims fainter","via":"harvest"},"note":"The axis at row 1109.4 (the pins' row 1187.5 less 0.8775 in), the loop's top at 1025.5: 83.9 px."}],"adopt":{"from":"photo-extended","reason":"As the length; the two agree within a hundredth."},"note":"Where the tube is in the two pictures on a rifle: the bore's axis, std.ar15.bore_axis_y above the pins' line, which the exposed tube bears out in the extended one (its top edge 0.56 in above that axis, the tube's radius less 2%)."},"butt_behind_pin_pos1":{"label":"Rear behind the takedown pin at its first position (all the way forward), on a mil-spec carbine tube","kind":"length","measurements":[{"id":"photo-extended","value":8.09,"unit":"in","pm":0.07,"source":{"type":"derived","expr":"{.butt_behind_pin_extended} - 4 * {bcm-receiver-extension.position_step}","via":"harvest"},"note":"The extended picture's reading, four of the tube's steps forward: ± the reading's and the step's (a generic figure)."},{"id":"photo-collapsed","value":8.05,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/sb-tactical-sba3 32ece668ff25 (SB Tactical: SBA_3_Black_Left_ghost_web.jpg, the same pistol with the brace collapsed, the rifle ghosted grey and the brace in colour, its true left side, 2500 x 2500)","scaleRef":"the lower's two pins, std.ar15 spacing 6.375 in: the pivot pin's head centred at (1144, 1187), the takedown pin's at (1711.5, 1188), on 8x gridded crops: 567.5 px, 89.02 px/in","method":"the brace's dark pixels (luminance under 90, which leaves the ghosted rifle out): the housing's front face at column 1870 (rows 1100 to 1120), the end cap's rear face at 2428: 558 px. ± as the extended picture's; the ghosting makes the pins' rims fainter","via":"harvest"},"note":"The end cap's rear face at column 2428, the takedown pin's centre at 1711.5: 716.5 px."},{"id":"end-plate","value":8.005,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"-{std.ar15.receiver_rear_x} + {bcm-end-plate.thickness} + {.length_collapsed}","via":"harvest"},"note":"The published collapsed length read as from the end plate's rear face: a reading of what the maker's figure spans."}],"adopt":{"from":"photo-extended","reason":"The extended picture's frame is the one that lands two standard figures (the receiver's rear face and the tube's width), as for the length. The collapsed picture's direct reading is 0.04 in further forward and would put the brace's front 0.03 in into the castle nut's drawing-set rear face (bcm-castle-nut.rear_face_behind_pin), as the MOE Carbine's own photo did: kept beside it, inside its ±. The derived figure rests on a reading of what the published length spans."},"note":"Read on the maker's two pictures of it on a pistol, framed by the lower's pins: extended (the fifth position) its rear is 10.73 in behind the pin, which is 8.09 at the first, four of the tube's steps forward (the maker: \"5-position adjustable\"); collapsed, the ghosted picture reads 8.05 directly. A third figure: the published 6.75 in, taken as measured from the end plate's rear face (the receiver's rear face, std.ar15.receiver_rear_x, and a mil-spec plate's thickness), gives 8.005. The two pictures' rears are 2.68 in apart: the tube's four steps (2.64) and the published 9.5 less 6.75 (2.75) either side."},"butt_behind_pin_extended":{"label":"Rear behind the takedown pin at full extension, on a mil-spec carbine tube","kind":"length","measurements":[{"id":"photo-extended","value":10.73,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/sb-tactical-sba3 94c73cb7eed3 (SB Tactical: SBA_3_Black_Left_Extended_web.jpg, an Aero M4E1 pistol with the brace at full extension, its true left side, in colour, 2500 x 2500)","scaleRef":"the lower's two pins, std.ar15 spacing 6.375 in: the pivot pin's head centred at (1062.5, 1138), the takedown pin's at (1561.5, 1139.5), on 6x and 8x gridded crops: 499 px, 78.27 px/in; level to 0.2 degrees","method":"the housing's front face at column 1901.5 (row 1030, above the tube's top edge) and the end cap's rear face at 2401 (rows 1050 to 1090), luminance under 120: 499.5 px. ± for the pins' centres (1.5 px each), the two faces (1.5 px each) and the brace's near side standing about 0.45 in nearer the lens than the pins' heads","via":"harvest"},"note":"The end cap's rear face at column 2401, the takedown pin's centre at 1561.5: 839.5 px."}]},"length_collapsed":{"label":"Length, collapsed (the maker's figure; as read, from the end plate's rear face to the brace's rear)","kind":"length","measurements":[{"id":"sb-sheet","value":6.75,"unit":"in","stated":"Length: 6.75\" Collapsed","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBA3 Pistol Stabilizing Brace specification sheet (REV DEC 2021; the product page's 'SBA3 Specification Sheet')","url":"https://www.sb-tactical.com/wp-content/uploads/SBA3_X_12821-1.pdf","retrieved":"2026-10-18","via":"harvest"}},{"id":"sb-page","value":6.75,"unit":"in","stated":"Length: Approximately 6.75″","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBA3 product page (the description)","url":"https://www.sb-tactical.com/product/sba3/","retrieved":"2026-10-18","via":"harvest"}},{"id":"primary-arms","value":6.75,"unit":"in","stated":"Length: 6.75\" – 9.5\"","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, SB Tactical SBA3 AR Pistol Brace (SKU: SBA3X-01-SB)","url":"https://www.primaryarms.com/sb-tactical-sba3-ar-pistol-stabilizing-brace-black-no-buffer-tube","retrieved":"2026-10-18","via":"harvest"}},{"id":"midwest","value":6.75,"unit":"in","stated":"Length - 6.75\", 7.5\", 8.25\", 9.0\", 9.5\"","source":{"type":"spec","publisher":"retailer","name":"Midwest Gun Works, SB Tactical AR-15 SBA3 Brace (SBA3-XX)","url":"https://www.midwestgunworks.com/page/mgwi/prod/sba3-xx","retrieved":"2026-10-18","via":"harvest"},"note":"The first of the five positions' lengths."}],"adopt":{"from":"sb-sheet","reason":"The maker's sheet, which names it collapsed; its page and two sellers repeat it."},"note":"The page calls it the length; the sheet says \"6.75\" Collapsed\". The brace alone is 6.38 in (length): this figure is what it adds behind the end plate at its first position (butt_behind_pin_pos1 less the receiver's rear face and the plate: 6.79 in the collapsed picture)."},"length_extended":{"label":"Length, extended (the maker's figure, as length_collapsed)","kind":"length","measurements":[{"id":"sb-sheet","value":9.5,"unit":"in","pm":0.05,"stated":"9.5\" Extended","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBA3 Pistol Stabilizing Brace specification sheet (REV DEC 2021; the product page's 'SBA3 Specification Sheet')","url":"https://www.sb-tactical.com/wp-content/uploads/SBA3_X_12821-1.pdf","retrieved":"2026-10-18","via":"harvest"}},{"id":"primary-arms","value":9.5,"unit":"in","pm":0.05,"stated":"Length: 6.75\" – 9.5\"","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, SB Tactical SBA3 AR Pistol Brace (SKU: SBA3X-01-SB)","url":"https://www.primaryarms.com/sb-tactical-sba3-ar-pistol-stabilizing-brace-black-no-buffer-tube","retrieved":"2026-10-18","via":"harvest"}},{"id":"midwest","value":9.5,"unit":"in","pm":0.05,"stated":"Length - 6.75\", 7.5\", 8.25\", 9.0\", 9.5\"","source":{"type":"spec","publisher":"retailer","name":"Midwest Gun Works, SB Tactical AR-15 SBA3 Brace (SBA3-XX)","url":"https://www.midwestgunworks.com/page/mgwi/prod/sba3-xx","retrieved":"2026-10-18","via":"harvest"},"note":"The last of the five positions' lengths."}],"adopt":{"from":"sb-sheet","reason":"The maker's sheet; two sellers repeat it."}},"cavity_depth":{"label":"Cavity depth (how deep the tube's bore runs into the brace from its front)","kind":"length","measurements":[{"id":"sb-sheet","value":6,"unit":"in","stated":"Cavity Depth: 6\"","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBA3 Pistol Stabilizing Brace specification sheet (REV DEC 2021; the product page's 'SBA3 Specification Sheet')","url":"https://www.sb-tactical.com/wp-content/uploads/SBA3_X_12821-1.pdf","retrieved":"2026-10-18","via":"harvest"}},{"id":"seat","value":6.219,"unit":"in","pm":0.1,"source":{"type":"derived","expr":"{bcm-receiver-extension.tube_front_behind_pin} + {bcm-receiver-extension.tube_length} - {.butt_behind_pin_pos1} + {.length} + {.bore_clearance}","via":"harvest"},"note":"As deep as the tube's rear end reaches at the collapsed seat, with the bore's clearance: what the collapsed picture requires of a 7.25 in tube."}],"adopt":{"from":"seat","reason":"The sheet's figure is stated to the inch; the depth the brace's own seat on a carbine tube requires is inside it, and keeps the tube out of the end cap's wall."},"note":"The sheet's \"Cavity Depth\", read as the bore the tube slides in (the instructions' \"pull down until the pin clears the tube cavity\"). Stated to the inch. A carbine tube (bcm-receiver-extension: screwed in to 0.669 in behind the pin, 7.25 in long, a generic figure) ends 7.92 in behind the pin, and at the collapsed seat the brace's front stands 1.71 in behind it: the bore has to run 6.22 in to take the tube there, inside the sheet's stated precision. The model's bore is that."},"strap_width":{"label":"Strap width","kind":"length","measurements":[{"id":"sb-sheet","value":1,"unit":"in","pm":0.05,"stated":"Strap Width: 1\"","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBA3 Pistol Stabilizing Brace specification sheet (REV DEC 2021; the product page's 'SBA3 Specification Sheet')","url":"https://www.sb-tactical.com/wp-content/uploads/SBA3_X_12821-1.pdf","retrieved":"2026-10-18","via":"harvest"},"note":"The webbing's width, to the tenth (the side view reads 1.07 across the strap's band, its fuzz included)."},{"id":"primary-arms","value":1,"unit":"in","pm":0.05,"stated":"Strap width: 1\"","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, SB Tactical SBA3 AR Pistol Brace (SKU: SBA3X-01-SB)","url":"https://www.primaryarms.com/sb-tactical-sba3-ar-pistol-stabilizing-brace-black-no-buffer-tube","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"sb-sheet","reason":"The maker's sheet; a seller repeats it."}},"strap_thickness":{"label":"Strap thickness (the nylon webbing with its hook and loop)","kind":"length","measurements":[{"id":"photo-rear","value":0.12,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sb-tactical-sba3 7c418fd9274e (SB Tactical: SBA3-rear-product_image.jpg, the brace straight from the rear, 2000 x 1500)","scaleRef":"the height (5.76 in) over the silhouette's 1065 rows (212 to 1277): 184.9 px/in","method":"the end cap's block across at row 420, inside the strap each side (columns 832 to 1172), on a 1.8x gridded crop","via":"harvest"},"note":"The band the strap makes beside the end cap's block on its left, 28 px (columns 804 to 832, row 450): 0.15 in with the loop side's fuzz, which the ± takes in."}]},"cuff_width":{"label":"The cuff's width over its strap, below the end cap's block","kind":"length","measurements":[{"id":"photo-rear","value":1.56,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/sb-tactical-sba3 7c418fd9274e (SB Tactical: SBA3-rear-product_image.jpg, the brace straight from the rear, 2000 x 1500)","scaleRef":"the height (5.76 in) over the silhouette's 1065 rows (212 to 1277): 184.9 px/in","method":"the end cap's block across at row 420, inside the strap each side (columns 832 to 1172), on a 1.8x gridded crop","via":"harvest"},"note":"280 px at row 950 (columns 864 to 1144) to 296 px lower down, where the strap lies looser round the fins: 1.51 to 1.60 in, the strap round each fin included."}]},"cuff_window_width":{"label":"The cuff's window across (the channel the forearm goes in)","kind":"length","measurements":[{"id":"photo-rear","value":1.05,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/sb-tactical-sba3 7c418fd9274e (SB Tactical: SBA3-rear-product_image.jpg, the brace straight from the rear, 2000 x 1500)","scaleRef":"the height (5.76 in) over the silhouette's 1065 rows (212 to 1277): 184.9 px/in","method":"the end cap's block across at row 420, inside the strap each side (columns 832 to 1172), on a 1.8x gridded crop","via":"harvest"},"note":"The white through it at its widest, 188 px at row 1050 (columns 913 to 1101) to 201 px: 1.02 to 1.09 in. Between rows 850 and 1000 a pad on each fin's inner face narrows it to 0.83 in (columns 929 to 1083 at row 950)."}]},"qd_bore_diameter":{"label":"QD socket's bore","kind":"length","measurements":[{"id":"photo-side","value":0.4,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sb-tactical-sba3 379c7f22b44e (SB Tactical: SBA3-black-product_image.jpg, the brace alone, its true left side, 2000 x 1500)","scaleRef":"the length and the height (6.38 and 5.76 in) over the silhouette's 1140 and 1041 px: 178.7 and 180.7 px/in, 1.1% apart","method":"the white disc seen through the socket, 72 px across on a 1.4x gridded crop","via":"harvest"}}]},"qd_cup_diameter":{"label":"QD socket's steel cup, across its rim","kind":"length","measurements":[{"id":"photo-side","value":0.55,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sb-tactical-sba3 379c7f22b44e (SB Tactical: SBA3-black-product_image.jpg, the brace alone, its true left side, 2000 x 1500)","scaleRef":"the length and the height (6.38 and 5.76 in) over the silhouette's 1140 and 1041 px: 178.7 and 180.7 px/in, 1.1% apart","method":"the white disc seen through the socket, 72 px across on a 1.4x gridded crop","via":"harvest"},"note":"The bright ring round the bore, 98 px across."}]},"pin_head_diameter":{"label":"The steel pins' heads (the lever's cross pin and the block's pin)","kind":"length","measurements":[{"id":"photo-side","value":0.1,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sb-tactical-sba3 379c7f22b44e (SB Tactical: SBA3-black-product_image.jpg, the brace alone, its true left side, 2000 x 1500)","scaleRef":"the length and the height (6.38 and 5.76 in) over the silhouette's 1140 and 1041 px: 178.7 and 180.7 px/in, 1.1% apart","method":"the white disc seen through the socket, 72 px across on a 1.4x gridded crop","via":"harvest"},"note":"The bright heads at (951, 567) and (951, 712), 18 px across."}]},"lower_inset":{"label":"How far the housing's lower part stands in from its sides under the ledge","kind":"length","measurements":[{"id":"assumed","value":0.12,"unit":"in","pm":0.06,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows the housing's lower part square from the front or from below; the oblique from behind and the left shows a lit ledge along the housing's side over it.","via":"harvest"}}]},"lever_thickness":{"label":"The adjustment lever's plate, thickness each side","kind":"length","measurements":[{"id":"assumed","value":0.08,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows the lever's plate edge-on.","via":"harvest"}}]},"relief_depth":{"label":"Depth of the two notches under the housing's ledge and of the groove along its lower part","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows them in profile.","via":"harvest"}}]},"endcap_inset":{"label":"How far the end cap's plate stands in from the block it is on, all round","kind":"length","measurements":[{"id":"photo-rear","value":0.08,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sb-tactical-sba3 7c418fd9274e (SB Tactical: SBA3-rear-product_image.jpg, the brace straight from the rear, 2000 x 1500)","scaleRef":"the height (5.76 in) over the silhouette's 1065 rows (212 to 1277): 184.9 px/in","method":"the end cap's block across at row 420, inside the strap each side (columns 832 to 1172), on a 1.8x gridded crop","via":"harvest"},"note":"The hexagon's outer edge at column 836 and the plate's at 850 on its left side, row 420 (1.8x gridded crop): 14 px."},{"id":"photo-side","value":0.07,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sb-tactical-sba3 379c7f22b44e (SB Tactical: SBA3-black-product_image.jpg, the brace alone, its true left side, 2000 x 1500)","scaleRef":"the length and the height (6.38 and 5.76 in) over the silhouette's 1140 and 1041 px: 178.7 and 180.7 px/in, 1.1% apart","method":"the white disc seen through the socket, 72 px across on a 1.4x gridded crop","via":"harvest"},"note":"The block's top at row 272 and the plate's at 285, columns 1510 to 1550: 13 px. Its foot is the seam's, within 3 px."}],"adopt":{"from":"photo-rear","reason":"The rear view shows the sides the model sets in; the side view's top, which the outline already draws, agrees within a hundredth."},"note":"The plate on the end cap's block's rear (its rear face the brace's rearmost), seen from the side as a step under the block's top and from the rear as a second outline inside the hexagon."},"pocket_depth":{"label":"Depth of the QD block's two recessed panels, each side","kind":"length","measurements":[{"id":"assumed","value":0.1,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the panels show dark in every side view and in none in profile.","via":"harvest"}}]},"bore_clearance":{"label":"The bore's clearance round a mil-spec tube, each side","kind":"length","measurements":[{"id":"assumed","value":0.01,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the bore is the tube's own section (std.receiver_extension) this much larger; the maker says only that fit 'may feel tighter or looser depending on the specific buffer tube used'.","via":"harvest"}}]}}},{"subject":"sb-tactical-sba4","title":"SB Tactical SBA4® AR Adjustable Pistol Stabilizing Brace®","dimensions":{"length":{"label":"Overall length","kind":"length","measurements":[{"id":"sb-page","value":7.5,"unit":"in","stated":"Length: Approximately 7.5″","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBA4® AR Adjustable Pistol Stabilizing Brace® (the description's figures; the spec tab: \"Length Approximately 7.5\"\")","url":"https://www.sb-tactical.com/product/sba4/","retrieved":"2026-10-18","via":"harvest"},"note":"The same figure as the sheets' 'Collapsed': a length on the rifle, by every reading of the brace itself 0.4 to 0.5 in more than the brace."},{"id":"wing","value":7,"unit":"in","stated":"Length: 7\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, SBA4 Brace From SB Tactical (SKU SBT-SBA4X; SPECIFICATIONS)","url":"https://www.wingtactical.com/firearm-parts-accessories/sb-tactical-sba4-pistol-stabilizing-brace/","retrieved":"2026-10-18","via":"harvest"},"note":"The shop's own figure, with its own photographs (watermarked) of the brace."},{"id":"on-rifle","value":7.09,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/sb-tactical-sba4 2d11fc6d89b2 (SB Tactical: SBA4_onGun_Left_ghost_web, the black brace collapsed on a ghosted AR pistol, its left side, 1766 px)","scaleRef":"the lower's pivot and takedown pins, (778.6, 828.6) and (1152.8, 829), 374.1 px for the standard's 6.375 in (std.ar15.pin_spacing): 58.69 px/in","method":"the brace's silhouette under luminance 80, from its mouth (column 1264) to the cuff's rear (1679): 416 px","via":"harvest"},"note":"± for the pins' centres and the brace's ends, a pixel each. The brace's side stands about 0.7 in nearer the lens than the pins' heads, so at any distance under about 55 in it reads 1.3% long: this reading is Wing Tactical's 7 in seen from there, and not a second figure against it."}],"adopt":{"from":"wing","reason":"The brace's own length, which the maker doesn't state alone: Wing Tactical's figure, borne out by the maker's on-rifle picture (7.09, a little nearer the lens than the pins it is scaled by) and by the maker's own side and rear views' proportions with the shop's height and the maker's width. The maker's 7.5 is its 'Collapsed' length on a rifle (length_collapsed), kept beside it."},"note":"The brace alone, from the cuff's rearmost point to the mouth round the tube. The maker's 7.5 is not this: its sheets give 7.5 as the brace's length 'Collapsed' and 10.25 'Extended' (the difference is four of the tube's 0.66 in steps and a little more), the SBA5's sheet gives 'Brace only' apart from 'Collapsed' (6.2 and 7.5), and on the maker's own picture of the brace collapsed on a rifle, framed by the lower's pins, the brace is 7.09 in long. Wing Tactical's 7 in, with its 5.31 in height, keeps the maker's straight side view's proportion to 0.6% and the straight rear view's (with the maker's 2.25 width) to 1%."},"height":{"label":"Height","kind":"length","measurements":[{"id":"wing","value":5.31,"unit":"in","stated":"Height: 5.31\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, SBA4 Brace From SB Tactical (SKU SBT-SBA4X; SPECIFICATIONS)","url":"https://www.wingtactical.com/firearm-parts-accessories/sb-tactical-sba4-pistol-stabilizing-brace/","retrieved":"2026-10-18","via":"harvest"}}],"note":"From the top of the strap's loop over the cuff to the cuff's foot. Only Wing Tactical states one; the maker's straight side view, scaled by the 7 in length, is 5.34 in high (1244 x 949 px), and the straight rear view, by the maker's 2.25 width, 5.36."},"width":{"label":"Width","kind":"length","measurements":[{"id":"sb-sheet","value":2.25,"unit":"in","stated":"Width (max): 2.25\"","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBA4 Pistol Stabilizing Brace specification sheet, REV DEC 2021 (Part Number SBA4X-01-SB, -02-SB, -03M-SB, -04-SB)","url":"https://www.sb-tactical.com/wp-content/uploads/SBA4_X_12821-2-1.pdf","retrieved":"2026-10-18","via":"harvest"}},{"id":"sb-page","value":2.25,"unit":"in","stated":"Width: Approximately 2.25″","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBA4® AR Adjustable Pistol Stabilizing Brace® (the description's figures; the spec tab: \"Length Approximately 7.5\"\")","url":"https://www.sb-tactical.com/product/sba4/","retrieved":"2026-10-18","via":"harvest"}},{"id":"sb-sheet-2020","value":2.25,"unit":"in","stated":"Width (max): 2.25\"","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBA4 Pistol Stabilizing Brace specification sheet, REV APRIL 2020 (the brace with a tube, Part Number SBA4-01-SB ...), hosted by Aerospace Arms","url":"https://aerospacearms.com/content/SBA4_42820.pdf","retrieved":"2026-10-18","via":"harvest"}},{"id":"wing","value":2.21,"unit":"in","stated":"Width: 2.21\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, SBA4 Brace From SB Tactical (SKU SBT-SBA4X; SPECIFICATIONS)","url":"https://www.wingtactical.com/firearm-parts-accessories/sb-tactical-sba4-pistol-stabilizing-brace/","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"sb-sheet","reason":"The maker's own figure for the widest point, on this product's sheet and its page; Wing Tactical's 2.21 is the shop's own, kept beside it."},"note":"The widest point: the housing's spade-shaped section near its rear (the rear view's widest row, 1.37 in under the loop's top). Wing Tactical's 2.21 is 1.8% under the maker's; the rear view's proportion with the shop's height reads 2.23."},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"sb-sheet","value":10.25,"unit":"oz","stated":"Weight: 10.25 oz","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBA4 Pistol Stabilizing Brace specification sheet, REV DEC 2021 (Part Number SBA4X-01-SB, -02-SB, -03M-SB, -04-SB)","url":"https://www.sb-tactical.com/wp-content/uploads/SBA4_X_12821-2-1.pdf","retrieved":"2026-10-18","via":"harvest"}},{"id":"sb-page","value":10,"unit":"oz","stated":"Weight: Approximately 10 oz","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBA4® AR Adjustable Pistol Stabilizing Brace® (the description's figures; the spec tab: \"Length Approximately 7.5\"\")","url":"https://www.sb-tactical.com/product/sba4/","retrieved":"2026-10-18","via":"harvest"}},{"id":"sb-sheet-2020","value":10,"unit":"oz","stated":"Weight: 10oz","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBA4 Pistol Stabilizing Brace specification sheet, REV APRIL 2020 (the brace with a tube, Part Number SBA4-01-SB ...), hosted by Aerospace Arms","url":"https://aerospacearms.com/content/SBA4_42820.pdf","retrieved":"2026-10-18","via":"harvest"},"note":"The same brace's earlier sheet, when it was sold with a tube; the figure is the brace's (the same as the page's)."},{"id":"wing","value":10.19,"unit":"oz","stated":"Weight: 10.19 oz.","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, SBA4 Brace From SB Tactical (SKU SBT-SBA4X; SPECIFICATIONS)","url":"https://www.wingtactical.com/firearm-parts-accessories/sb-tactical-sba4-pistol-stabilizing-brace/","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"sb-sheet","reason":"The maker's sheet for this product (the brace alone, SBA4X), to a quarter ounce; the page's 'approximately 10' and Wing Tactical's 10.19 are within it."},"note":"The brace with its strap (the sheet: \"Comes with adjustable nylon strap\")."},"length_collapsed":{"label":"The maker's length 'Collapsed' (its datum on the rifle not stated)","kind":"length","measurements":[{"id":"sb-sheet","value":7.5,"unit":"in","stated":"Length: Collapsed: 7.5\"","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBA4 Pistol Stabilizing Brace specification sheet, REV DEC 2021 (Part Number SBA4X-01-SB, -02-SB, -03M-SB, -04-SB)","url":"https://www.sb-tactical.com/wp-content/uploads/SBA4_X_12821-2-1.pdf","retrieved":"2026-10-18","via":"harvest"}},{"id":"sb-sheet-2020","value":7.5,"unit":"in","stated":"Length: Collapsed: 7.5\"","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBA4 Pistol Stabilizing Brace specification sheet, REV APRIL 2020 (the brace with a tube, Part Number SBA4-01-SB ...), hosted by Aerospace Arms","url":"https://aerospacearms.com/content/SBA4_42820.pdf","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"sb-sheet","reason":"This product's sheet; the 2020 sheet says the same."},"note":"Kept as published. With the brace collapsed on the maker's rifle its rear is 8.96 in behind the takedown pin and 7.83 behind the lower's rear face (std.ar15.receiver_rear_x): 7.5 is neither, nor the brace alone (7). Not used by the model or the build."},"length_extended":{"label":"The maker's length 'Extended' (its datum on the rifle not stated)","kind":"length","measurements":[{"id":"sb-sheet","value":10.25,"unit":"in","stated":"Extended: 10.25\"","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBA4 Pistol Stabilizing Brace specification sheet, REV DEC 2021 (Part Number SBA4X-01-SB, -02-SB, -03M-SB, -04-SB)","url":"https://www.sb-tactical.com/wp-content/uploads/SBA4_X_12821-2-1.pdf","retrieved":"2026-10-18","via":"harvest"}},{"id":"sb-sheet-2020","value":10.25,"unit":"in","stated":"Extended: 10.25\"","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBA4 Pistol Stabilizing Brace specification sheet, REV APRIL 2020 (the brace with a tube, Part Number SBA4-01-SB ...), hosted by Aerospace Arms","url":"https://aerospacearms.com/content/SBA4_42820.pdf","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"sb-sheet","reason":"This product's sheet; the 2020 sheet says the same."},"note":"Kept as published: 2.75 in more than 'Collapsed', where the brace's five positions are four of the tube's 0.66 in steps (2.64) apart."},"cavity_depth":{"label":"Depth of the tube's cavity, from the mouth","kind":"length","measurements":[{"id":"sb-sheet","value":6.75,"unit":"in","stated":"Cavity Depth: 6.75\"","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBA4 Pistol Stabilizing Brace specification sheet, REV DEC 2021 (Part Number SBA4X-01-SB, -02-SB, -03M-SB, -04-SB)","url":"https://www.sb-tactical.com/wp-content/uploads/SBA4_X_12821-2-1.pdf","retrieved":"2026-10-18","via":"harvest"}},{"id":"sb-sheet-2020","value":6.75,"unit":"in","stated":"Cavity Depth: 6.75\"","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBA4 Pistol Stabilizing Brace specification sheet, REV APRIL 2020 (the brace with a tube, Part Number SBA4-01-SB ...), hosted by Aerospace Arms","url":"https://aerospacearms.com/content/SBA4_42820.pdf","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"sb-sheet","reason":"This product's sheet; the 2020 sheet says the same."}},"strap_width":{"label":"Strap width","kind":"length","measurements":[{"id":"sb-sheet","value":1,"unit":"in","stated":"Strap Width: 1\"","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBA4 Pistol Stabilizing Brace specification sheet, REV DEC 2021 (Part Number SBA4X-01-SB, -02-SB, -03M-SB, -04-SB)","url":"https://www.sb-tactical.com/wp-content/uploads/SBA4_X_12821-2-1.pdf","retrieved":"2026-10-18","via":"harvest"}},{"id":"sb-sheet-2020","value":1,"unit":"in","stated":"Strap Width: 1\"","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBA4 Pistol Stabilizing Brace specification sheet, REV APRIL 2020 (the brace with a tube, Part Number SBA4-01-SB ...), hosted by Aerospace Arms","url":"https://aerospacearms.com/content/SBA4_42820.pdf","retrieved":"2026-10-18","via":"harvest"}},{"id":"side-photo","value":1.01,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/sb-tactical-sba4 dc891b83a89c (SB Tactical: the black brace straight from its left, 1766 px)","scaleRef":"the brace's 7 in length and 5.31 in height (1244 and 949 px: 178.2 px/in)","method":"the strap's two edges across the cuff, columns 1185 and 1365: 180 px","via":"harvest"},"note":"A check of the side view's scale."}],"adopt":{"from":"sb-sheet","reason":"This product's sheet; the photo agrees."}},"loop_above_top":{"label":"The strap's loop over the cuff: its top above the housing's top edge","kind":"length","measurements":[{"id":"side-photo","value":0.331,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/sb-tactical-sba4 dc891b83a89c (SB Tactical: the black brace straight from its left, 1766 px)","scaleRef":"the brace's 7 in length and 5.31 in height (178.2 px/in)","method":"the loop's top, row 406, over the housing's top edge, row 465, along the mouth's first five inches: 59 px","via":"harvest"}}],"note":"The loop is the brace's highest point and the side and rear outlines' origin; the housing's top edge runs level from the mouth to the step ahead of the cuff."},"tube_axis_below_top":{"label":"Tube axis below the housing's top edge","kind":"length","measurements":[{"id":"on-rifle","value":0.65,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sb-tactical-sba4 b370ca556839 (SB Tactical: SBA4_onGun_Left_Extended_web, the brace extended on an AR pistol, the tube bare between the castle nut and the mouth, 1766 px)","scaleRef":"the tube's own 1.148 in (std.receiver_extension.milspec_od), 61.5 px across where no rail is (columns 1180 to 1220), and the indexing rail's foot 45.8 px under the tube's axis for the standard's 0.874 (std.receiver_extension.rail_bottom_below_axis): 53.5 px/in, and 55.2 if the black tube reads 3% thin on white","method":"the housing's top edge at the mouth (row 760.5) and the tube's top and bottom edges (rows 764.5 and 826), columns read down at half the step in brightness: the axis 35.3 px under the housing's top","via":"harvest"},"note":"± for the two scales and a pixel at each edge."}]},"tube_axis_below_crest":{"label":"Tube axis below the top of the strap's loop (where the outlines' origin is)","kind":"length","measurements":[{"id":"derived","value":0.981,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.tube_axis_below_top} + {.loop_above_top}","via":"harvest"}}]},"butt_behind_pin_pos1":{"label":"Rear behind the takedown pin at its first position (all the way forward), on a mil-spec carbine tube","kind":"length","measurements":[{"id":"on-rifle","value":8.96,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/sb-tactical-sba4 2d11fc6d89b2 (SB Tactical: SBA4_onGun_Left_ghost_web, the brace collapsed on an AR pistol, left side, 1766 px)","scaleRef":"the lower's pins, 58.69 px/in (std.ar15.pin_spacing)","method":"the brace's mouth (column 1264.5) 17 px behind the castle nut's rear face (1247.5): 0.29 in, from the castle nut's rear face at bcm-castle-nut.rear_face_behind_pin, 1.668, to 1.958; and the brace's own 7 in behind it","via":"harvest"},"note":"± for the castle nut's own figure (a reading in conflict), the gap's two pixels, and the length's."},{"id":"pin-framed","value":8.97,"unit":"in","pm":0.18,"source":{"type":"photo","photo":"references/sb-tactical-sba4 2d11fc6d89b2","scaleRef":"the lower's pins, 58.69 px/in","method":"the cuff's rear (column 1679) behind the takedown pin (1152.8): 526.3 px","via":"harvest"},"note":"Read across the photo at the pins' scale: the cuff stands about 0.7 in nearer the lens than the pins and 800 px off the picture's middle, which moves it by up to 0.17 in toward the middle by where the lens stood (not read). A check of the first."}],"adopt":{"from":"on-rifle","reason":"Read locally, from the castle nut's rear face next to the mouth, where the lens's place moves nothing; the pin-framed reading of the rear agrees within its ±."},"note":"Collapsed, as the maker pictures it on a rifle: the brace's mouth stands 0.29 in behind the castle nut's rear face. Its lock pin isn't seen in any photo (the boss under the lever is 4.64 in behind the pin there, on neither of the tube's first two holes, 4.18 and 4.84), so which of the tube's holes this is isn't read: the brace's own five positions are counted from here (its extended picture stands about four steps further back)."},"qd_ring_diameter":{"label":"QD socket's steel insert: outside diameter (its rim, each side)","kind":"length","measurements":[{"id":"side-photo","value":0.42,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sb-tactical-sba4 dc891b83a89c","scaleRef":"178.2 px/in (the brace's length and height)","method":"the insert's rim on a 4x crop, columns 276 to 351, rows 673 to 750: 75 px","via":"harvest"}}]},"qd_bore_diameter":{"label":"QD socket's bore","kind":"length","measurements":[{"id":"side-photo","value":0.29,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sb-tactical-sba4 dc891b83a89c","scaleRef":"178.2 px/in","method":"the bright ground through the bore on a 4x crop, columns 288 to 339: 51 px","via":"harvest"}}]},"block_width":{"label":"The lever block's width (between the strut's two bars)","kind":"length","measurements":[{"id":"rear-photo","value":0.78,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sb-tactical-sba4 d3dfd7f2e1fa (SB Tactical: SBA4_Rear_web, straight from behind, 1179 px)","scaleRef":"the brace's 5.31 in height and 2.25 in width (862 and 362 px: 161.6 px/in)","method":"the opening between the flaps at its top, where the block's underside closes it: 126 px","via":"harvest"},"note":"The block fills the gap between the bars in Wing Tactical's views from below (86a19fea5a2d, a8a4eb10c3a1)."}]},"boss_width":{"label":"The boss under the lever: its width across the brace","kind":"length","measurements":[{"id":"rear-photo","value":0.34,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sb-tactical-sba4 d3dfd7f2e1fa","scaleRef":"161.6 px/in","method":"the boss seen in the opening's top, columns 553 to 608: 55 px","via":"harvest"}}]},"loop_width":{"label":"The strap's loop over the cuff: its width across the brace","kind":"length","measurements":[{"id":"rear-photo","value":0.33,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sb-tactical-sba4 d3dfd7f2e1fa","scaleRef":"161.6 px/in","method":"the tab at the top, columns 566 to 620: 54 px","via":"harvest"}}]},"loop_bar_thickness":{"label":"The strap's loop over the cuff: the bar over the strap (its depth, top to underside)","kind":"length","measurements":[{"id":"side-photo","value":0.067,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/sb-tactical-sba4 dc891b83a89c","scaleRef":"178.2 px/in","method":"the loop's top (row 406) to the window's top over the strap (row 418), columns 1190 to 1360: 12 px","via":"harvest"},"note":"± two pixels: the window is a sliver of white ground between the bar and the strap's top."}]},"lever_pin_diameter":{"label":"The pin through the lever's plate (its end, each side)","kind":"length","measurements":[{"id":"side-photo","value":0.11,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sb-tactical-sba4 dc891b83a89c","scaleRef":"178.2 px/in","method":"the pin's dark end in the rounded square on the lever, on a 3x crop: 20 px across","via":"harvest"}}]},"lever_slot_depth":{"label":"Depth of the lever plate's three small slots and of the rounded square round its pin","kind":"length","measurements":[{"id":"assumed","value":0.04,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the side views show each as a dark rim round a lit floor, and no view shows one in section.","via":"harvest"}}]},"rear_seam_width":{"label":"The seam round the rear face's spade panel and its medallion: its width","kind":"length","measurements":[{"id":"rear-photo","value":0.04,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/sb-tactical-sba4 d3dfd7f2e1fa","scaleRef":"161.6 px/in","method":"the dark line round the panel, 3 to 4 px, taken as the shadowed wall of a groove whose lit wall beside it is as wide: twice 3.5 px","via":"harvest"},"note":"A fine groove lit from one side reads as its shadow alone, half its width."}]},"rear_seam_depth":{"label":"The seam round the rear face's panel: its depth","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the rear view shows the seam's line, and no view shows it in section.","via":"harvest"}}]},"slot_depth":{"label":"Depth of the nine slots in the housing's sides","kind":"length","measurements":[{"id":"assumed","value":0.12,"unit":"in","pm":0.06,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows a slot in section. The obliques show them deep and dark, and one in Primary Arms' right view shows the ground through it (into the cavity); they are drawn as recesses of this depth.","via":"harvest"}}]},"strap_thickness":{"label":"The strap's thickness","kind":"length","measurements":[{"id":"assumed","value":0.05,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the sheet gives the strap's width (1 in) and no view shows its edge square.","via":"harvest"}}]},"bore_clearance":{"label":"The cavity's clearance round a mil-spec tube and its rail (radial)","kind":"length","measurements":[{"id":"assumed","value":0.01,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the cavity is drawn as the mil-spec tube and its indexing rail with this much room, so that the brace's faces and the tube's are not drawn in one place.","via":"harvest"}}]}}},{"subject":"sb-tactical-sba5","title":"SB Tactical SBA5® AR Adjustable Pistol Stabilizing Brace®","dimensions":{"length":{"label":"Overall length (the brace alone)","kind":"length","measurements":[{"id":"sheet","value":6.2,"unit":"in","stated":"Length: 6.2\"  Brace only","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBA5 Pistol Stabilizing Brace specification sheet (FEB 2026)","url":"https://www.sb-tactical.com/wp-content/uploads/SBA5-Spec-Sheet-020326.pdf","retrieved":"2026-10-18","via":"harvest"}},{"id":"page","value":6.125,"unit":"in","pm":0.05,"stated":"Length: Approximately 6.125″","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBA5® AR Adjustable Pistol Stabilizing Brace® (product page: its description and its spec tab)","url":"https://www.sb-tactical.com/product/sba5/","retrieved":"2026-10-18","via":"harvest"},"note":"\"Approximately\", in the page's description and again in its spec tab (\"Length Approximately 6.125\\\"\"): its ± is taken as the sheet's last digit's, 0.05."},{"id":"wing","value":6.2,"unit":"in","stated":"Length: 6.2\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, SB Tactical SBA5 Pistol Stabilizing Brace (MPN SBA5X-01-SB / SBA5X-02-SB; SPECIFICATIONS)","url":"https://www.wingtactical.com/firearm-parts-accessories/ar-15-parts/ar-15-buffer-systems/ar-15-buffer-tube-accessories/sb-tactical-sba5-pistol-stabilizing-brace/","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"sheet","reason":"The maker's newest document (FEB 2026), which names what it measures (the brace alone); a seller's table repeats it. The page's \"Approximately 6.125\" is 1.2% under it, inside the page's own ±."},"note":"From the front of the housing round the tube to the cuff's rearmost face. The sheet's figure is for the brace alone (\"Brace only\"), apart from its collapsed and extended lengths; the page's is \"Approximately 6.125\". Wing Tactical's table repeats the sheet's. The maker's straight side photo, scaled by the sheet's length and Wing Tactical's height together, is the check (the trace's own scales)."},"height":{"label":"Height","kind":"length","measurements":[{"id":"wing","value":5.4,"unit":"in","stated":"Height: 5.4\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, SB Tactical SBA5 Pistol Stabilizing Brace (MPN SBA5X-01-SB / SBA5X-02-SB; SPECIFICATIONS)","url":"https://www.wingtactical.com/firearm-parts-accessories/ar-15-parts/ar-15-buffer-systems/ar-15-buffer-tube-accessories/sb-tactical-sba5-pistol-stabilizing-brace/","retrieved":"2026-10-18","via":"harvest"},"note":"A seller's own table, with its own weight (9.21 oz) and width (2.16 in): one seller, provisional."},{"id":"side-photo","value":5.16,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sb-tactical-sba5 4d01fa8999c1 (SB Tactical: SBA5-left-web-1.jpg, straight left side on white, 1500 px)","scaleRef":"the sheet's length, 6.2 in = 1210 px (195.2 px/in), the silhouette's ends","method":"the silhouette's height, 1007 px (luminance < 235): the strap's tab's top to the cuff's foot","via":"harvest"},"note":"The maker's FDE picture of the same view keeps the proportion to 0.1% (1128 x 938 px), and the brace pasted into the maker's two pistol pictures to 0.2% (360 x 299). ± for the silhouette's ends (2 px each) and the length's last digit."},{"id":"rear-photo","value":5.18,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/sb-tactical-sba5 3bebaaf0244d (SB Tactical: SBA5-rear-web-1.jpg, straight from behind on white, 1179 px)","scaleRef":"the maker's 2.1 in width (max) = the end cap's 415 px at its widest, the strap left out (197.6 px/in)","method":"the silhouette's height, 1023 px (luminance < 235): the strap's tab's top to the flaps' foot","via":"harvest"},"note":"An independent check of the side photo's reading: another view, scaled by the other published size. ± for where the strap's edge leaves the cap's (5 px)."}],"adopt":{"from":"side-photo","reason":"The maker's own pictures, scaled each by one of the maker's two published sizes (its length in the side view, its width in the view from behind), agree on it within 0.02 in. Wing Tactical's 5.4 is 4.5% over it and stays beside it: the seller's own photographs (Primary Arms' and the green one, taken from nearer and behind) make the cuff, the tallest part, read taller, which may be where it comes from."},"note":"From the top of the strap's loop over the cuff to the cuff's lowest point. The maker states none (its page, its sheet and its shared instructions read 2026-10-18); Wing Tactical's table is the one figure on file."},"width":{"label":"Width (max)","kind":"length","measurements":[{"id":"sheet","value":2.1,"unit":"in","stated":"Width (max): 2.1\"","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBA5 Pistol Stabilizing Brace specification sheet (FEB 2026)","url":"https://www.sb-tactical.com/wp-content/uploads/SBA5-Spec-Sheet-020326.pdf","retrieved":"2026-10-18","via":"harvest"}},{"id":"page","value":2.1,"unit":"in","stated":"Max Width Approximately 2.1\"","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBA5® AR Adjustable Pistol Stabilizing Brace® (product page: its description and its spec tab)","url":"https://www.sb-tactical.com/product/sba5/","retrieved":"2026-10-18","via":"harvest"}},{"id":"wing","value":2.16,"unit":"in","stated":"Width: 2.16\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, SB Tactical SBA5 Pistol Stabilizing Brace (MPN SBA5X-01-SB / SBA5X-02-SB; SPECIFICATIONS)","url":"https://www.wingtactical.com/firearm-parts-accessories/ar-15-parts/ar-15-buffer-systems/ar-15-buffer-tube-accessories/sb-tactical-sba5-pistol-stabilizing-brace/","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"sheet","reason":"The maker's figure, on its sheet and its page alike. Wing Tactical's 2.16 is the shop's own, 3% over it, kept beside it."},"note":"The widest place: the cuff, with the strap round it (the maker's view from the rear). What the page and the sheet measure across is not said."},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"sheet","value":9,"unit":"oz","stated":"Weight: 9 oz","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBA5 Pistol Stabilizing Brace specification sheet (FEB 2026)","url":"https://www.sb-tactical.com/wp-content/uploads/SBA5-Spec-Sheet-020326.pdf","retrieved":"2026-10-18","via":"harvest"}},{"id":"page","value":9.5,"unit":"oz","stated":"Weight: Approximately 9.5 oz","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBA5® AR Adjustable Pistol Stabilizing Brace® (product page: its description and its spec tab)","url":"https://www.sb-tactical.com/product/sba5/","retrieved":"2026-10-18","via":"harvest"},"note":"Also the spec tab: \"Weight 9.5 oz\"."},{"id":"primary-arms","value":9,"unit":"oz","stated":"Weight: 9 oz","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, SB Tactical SBA5 AR Pistol Brace (SKU: SBA5-BLK MPN: SBA5-BLK; Features)","url":"https://www.primaryarms.com/sb-tactical-sba5-ar-pistol-stabilizing-brace-black","retrieved":"2026-10-18","via":"harvest"}},{"id":"wing","value":9.21,"unit":"oz","stated":"Weight: 9.21 oz.","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, SB Tactical SBA5 Pistol Stabilizing Brace (MPN SBA5X-01-SB / SBA5X-02-SB; SPECIFICATIONS)","url":"https://www.wingtactical.com/firearm-parts-accessories/ar-15-parts/ar-15-buffer-systems/ar-15-buffer-tube-accessories/sb-tactical-sba5-pistol-stabilizing-brace/","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"sheet","reason":"The maker's newest document (FEB 2026); a seller repeats it, and a second seller's own 9.21 oz is between it and the page's \"Approximately 9.5 oz\", which is kept beside it."},"note":"The maker gives two: \"Approximately 9.5 oz\" on its page and 9 oz on its newer sheet, which Primary Arms repeats; Wing Tactical's table says 9.21 oz. Whether the strap is weighed with it is not said."},"length_collapsed":{"label":"Length, collapsed (the maker's figure; what it is measured between is not said)","kind":"length","measurements":[{"id":"sheet","value":7.5,"unit":"in","pm":0.05,"stated":"7.5\"  Collapsed","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBA5 Pistol Stabilizing Brace specification sheet (FEB 2026)","url":"https://www.sb-tactical.com/wp-content/uploads/SBA5-Spec-Sheet-020326.pdf","retrieved":"2026-10-18","via":"harvest"}},{"id":"primary-arms","value":7.5,"unit":"in","pm":0.05,"stated":"5-position adjustable, 7.5\" collapsed to 10.25\" extended","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, SB Tactical SBA5 AR Pistol Brace (SKU: SBA5-BLK MPN: SBA5-BLK; Features)","url":"https://www.primaryarms.com/sb-tactical-sba5-ar-pistol-stabilizing-brace-black","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"sheet","reason":"The maker's figure; the seller repeats it."},"note":"With the brace alone 6.2 in on the same sheet, 7.5 in is measured to something ahead of the brace's own front, which the sheet doesn't name. Not used to seat it: its seat is read on the maker's picture of it on a pistol (butt_behind_pin_pos1)."},"length_extended":{"label":"Length, extended (the maker's figure, on the same basis as the collapsed one)","kind":"length","measurements":[{"id":"sheet","value":10.25,"unit":"in","stated":"10.25\"   Extended","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBA5 Pistol Stabilizing Brace specification sheet (FEB 2026)","url":"https://www.sb-tactical.com/wp-content/uploads/SBA5-Spec-Sheet-020326.pdf","retrieved":"2026-10-18","via":"harvest"}},{"id":"primary-arms","value":10.25,"unit":"in","stated":"5-position adjustable, 7.5\" collapsed to 10.25\" extended","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, SB Tactical SBA5 AR Pistol Brace (SKU: SBA5-BLK MPN: SBA5-BLK; Features)","url":"https://www.primaryarms.com/sb-tactical-sba5-ar-pistol-stabilizing-brace-black","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"sheet","reason":"The maker's figure; the seller repeats it."},"note":"Four steps on from collapsed (five positions): 2.75 in, 0.69 in a step."},"strap_width":{"label":"Strap width","kind":"length","measurements":[{"id":"sheet","value":1,"unit":"in","pm":0.05,"stated":"Strap Width: 1\"","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBA5 Pistol Stabilizing Brace specification sheet (FEB 2026)","url":"https://www.sb-tactical.com/wp-content/uploads/SBA5-Spec-Sheet-020326.pdf","retrieved":"2026-10-18","via":"harvest"},"note":"Written as a whole inch on a sheet whose other lengths go to a tenth: its ± is taken as theirs."}]},"cavity_depth":{"label":"Cavity depth (how far the tube goes in, from the brace's front)","kind":"length","measurements":[{"id":"sheet","value":6,"unit":"in","pm":0.05,"stated":"Cavity Depth: 6\"","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBA5 Pistol Stabilizing Brace specification sheet (FEB 2026)","url":"https://www.sb-tactical.com/wp-content/uploads/SBA5-Spec-Sheet-020326.pdf","retrieved":"2026-10-18","via":"harvest"},"note":"Written as a whole inch on a sheet whose other lengths go to a tenth: its ± is taken as theirs."}]},"tube_axis_below_top":{"label":"Tube axis below the brace's top (the top of the strap's tab)","kind":"length","measurements":[{"id":"sum","value":0.957,"unit":"in","source":{"type":"derived","expr":"{.tab_above_housing_top} + {.tube_axis_below_housing_top}","via":"harvest"}}],"note":"The profiles' origin is the tab's top, the outline's highest point; the axis is read below the housing's own top, which the tab stands over."},"tab_above_housing_top":{"label":"The strap's tab, its top over the housing's top line","kind":"length","measurements":[{"id":"photo","value":0.297,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/sb-tactical-sba5 4d01fa8999c1 (SB Tactical: SBA5-left-web-1.jpg, straight left side on white, 1500 px)","scaleRef":"the sheet's length, 6.2 in = 1210 px (195.2 px/in)","method":"rows 254 (the tab's top) and 312 (the housing's top, level from the mouth to the tab) on a 1.2x gridded crop","via":"harvest"},"note":"The view from behind reads the tab 62 px tall at 197.6 px/in, 0.31 in: it agrees."}]},"tube_axis_below_housing_top":{"label":"The tube's axis below the housing's top line","kind":"length","measurements":[{"id":"wall","value":0.66,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{std.receiver_extension.milspec_od} / 2 + {.bore_top_wall}","via":"harvest"}}],"note":"No view on file shows the mouth square. The bore is taken as the mil-spec tube's own diameter under the wall the oblique shows over it (bore_top_wall); the maker's ghost pistol picture puts the tube's top at the housing's top line (the brace is pasted in), which this allows within its ±."},"bore_top_wall":{"label":"The housing's wall over the bore, at the mouth","kind":"length","measurements":[{"id":"photo","value":0.086,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/sb-tactical-sba5 8620d50554a2 (Primary Arms: SBA5-BLK_03, the brace from the front, the left and above, 2200 px)","scaleRef":"the mouth's own height in the same face (the bore over the indexing rail's channel: the mil-spec tube's top to its rail's foot, 1.448 in by std.receiver_extension), about 300 px","method":"the rim over the bore's top, 15 to 20 px on a 1.2x gridded crop, read as a share of the mouth's height in the one plane of the front face","via":"harvest"},"note":"± for where the rim's inner and outer edges are in an oblique with the face's top lit."}]},"lock_pin_ahead_of_butt":{"label":"The lock pin (the lever's cross pin) ahead of the brace's rear","kind":"length","measurements":[{"id":"photo","value":3.907,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sb-tactical-sba5 4d01fa8999c1 (SB Tactical: SBA5-left-web-1.jpg, straight left side on white, 1500 px)","scaleRef":"the sheet's length, 6.2 in = 1210 px (195.2 px/in)","method":"the two pins' heads' centres, columns 567 and 568, against the cuff's rearmost column 1330, on a 1.2x gridded crop","via":"harvest"}}],"note":"The maker's instructions: \"Grasp the adjustment lever at the cross pin for the SBA3, SBA5 and SBA6 ... and pull down until the pin clears the tube cavity\". The lever's two pins stand one over the other at its rear end; the lock pin is taken to be under the upper one, the cross pin."},"pin_diameter":{"label":"The lever's pins, the heads' diameter","kind":"length","measurements":[{"id":"photo","value":0.077,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/sb-tactical-sba5 4d01fa8999c1 (SB Tactical: SBA5-left-web-1.jpg, straight left side on white, 1500 px)","scaleRef":"the sheet's length, 6.2 in = 1210 px (195.2 px/in)","method":"each head about 15 px across on a 1.2x gridded crop","via":"harvest"}}]},"qd_bore_diameter":{"label":"The QD socket's bore","kind":"length","measurements":[{"id":"photo","value":0.37,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sb-tactical-sba5 4d01fa8999c1 (SB Tactical: SBA5-left-web-1.jpg, straight left side on white, 1500 px)","scaleRef":"the sheet's length, 6.2 in = 1210 px (195.2 px/in)","method":"the dark round in the socket's panel, about 72 px across, centred at column 887, row 617","via":"harvest"}}]},"strap_thickness":{"label":"The strap's thickness","kind":"length","measurements":[{"id":"assumed","value":0.06,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows the strap's edge square. The sheet says only that it is nylon, 1 in wide.","via":"harvest"}}]},"panel_depth":{"label":"The QD socket's panel and the blank panel, how deep each is recessed in the housing's side","kind":"length","measurements":[{"id":"assumed","value":0.06,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: both side views show each panel's rim as a step, and no view shows it in profile.","via":"harvest"}}]},"groove_depth":{"label":"The parting lines' depth and width (round the lever, the cap's seam with the flaps, the groove along the housing's front)","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: each line is a dark hairline in the side views, a few pixels across, and no view shows one in profile.","via":"harvest"}}]},"flap_wall":{"label":"The cuff's flaps, how thick each wall is round the opening between them","kind":"length","measurements":[{"id":"photo","value":0.25,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sb-tactical-sba5 3bebaaf0244d (SB Tactical: SBA5-rear-web-1.jpg, straight from behind on white, 1179 px)","scaleRef":"the end cap's 415 px at its widest for the maker's 2.1 in (197.6 px/in)","method":"the rim's width across, left and right, on rows 600 to 700 of a gridded crop: 55 and 46 px; and over the opening's top, under the cap's seam, about 55 px","via":"harvest"}}],"note":"From behind, the flaps' rear faces are a rim round the opening, and inside the rim their inner faces run forward in shadow to where the ground shows through. The opening is drawn at the rim's inner edge, the whole length of the cuff (its inner faces' lean forward isn't read)."},"split_width":{"label":"The split between the cuff's two flaps, at their foot","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the view from behind shows the split as a line about 4 px across at 198 px/in.","via":"harvest"}}]},"butt_behind_pin_pos1":{"label":"Rear behind the takedown pin at its first position (all the way forward), on a mil-spec carbine receiver extension","kind":"length","measurements":[{"id":"holes","value":8.746,"unit":"in","pm":0.08,"source":{"type":"derived","expr":"{bcm-receiver-extension.tube_front_behind_pin} + {bcm-receiver-extension.tube_length} - {bcm-receiver-extension.position_hole_rear_from_rear} - 4 * {bcm-receiver-extension.position_step} + {.lock_pin_ahead_of_butt}","via":"harvest"},"note":"The lock pin in the tube's second hole. ± for the hole's place (0.03), the tube's seat (0.02), the pin's place in the brace (0.04) and the tube's length, a generic figure."},{"id":"sheet","value":8.625,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{.length_collapsed} - {std.ar15.receiver_rear_x}","via":"harvest"},"note":"The sheet's collapsed length read as measured from the receiver's rear face: a reading of what the sheet doesn't say."},{"id":"ghost","value":8.57,"unit":"in","pm":0.1,"source":{"type":"photo","photo":"references/sb-tactical-sba5 f6a9a3820ca3 (SB Tactical: SBA5-on-pistol-left-ghost-web-1.jpg, a ghosted AR pistol from its left with the brace pasted in, 1766 px)","scaleRef":"pin frame: takedown (1210.4, 840.6), pivot (846.9, 843.9) = 6.375 in apart (57.0 px/in), the heads' centres on 8x crops","method":"the brace's rearmost dark column, 1699, behind the takedown pin's head","via":"harvest"},"note":"The brace is pasted in at 58.1 px/in by its own length (1.8% off the pins' scale), and the maker's colour picture of the same pistol has it pasted 0.3 in further forward, against the castle nut: an artist's placement."}],"adopt":{"from":"holes","reason":"A seat is where two parts touch: the lock pin in the tube's hole, the first one the cavity's depth lets it reach. The sheet's lengths, read from the receiver's rear face, agree within 0.12 in and put its last position at the tube's rear hole within 0.01; the pasted pictures are kept beside it."},"note":"Five positions on a tube of six holes: its first is the tube's SECOND hole from the front. At the front hole, with its lock pin 3.91 in ahead of its rear and its cavity 6 in deep, the tube's rear end (7.92 in behind the pin) would stand at the cavity's floor (1.90 + 6.0 = 7.90): the brace doesn't go that far forward. At the second hole its rear stands 7.62 in behind the receiver's rear face, and at the sixth 10.26: the sheet's \"7.5\" Collapsed 10.25\" Extended\", if they are measured from the receiver's rear face, which the sheet doesn't say (its 0.69 in a step against the tube's 0.66). Its front then stands 0.90 in behind the castle nut. The maker's pictures of it on a pistol are its side picture pasted in, once with 0.6 in of tube showing and once against the castle nut: kept as a reading, not a seat."}}},{"subject":"sb-tactical-sbpdw-brace","title":"SB Tactical SBPDW® Pistol Stabilizing Brace® (the brace: its polymer body, cuff and strap, and its two guide rods)","dimensions":{"length":{"label":"Length collapsed (the maker's; what it is measured between isn't stated)","kind":"length","measurements":[{"id":"sheet","value":6.75,"unit":"in","stated":"Length: 6.75\" Collapsed 9.4\" Extended","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBPDW specification sheet (REV FEBRUARY 2022), linked from the product page as 'SBPDW Specification Sheet'","url":"https://www.sb-tactical.com/wp-content/uploads/SBPDW_3422-1.pdf","retrieved":"2026-10-18","via":"harvest"}},{"id":"primary-arms","value":6.75,"unit":"in","stated":"across the brace's 3 positions, from 6.75\" collapsed to 9.375\" extended","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, SB Tactical SBPDW AR Pistol Brace (SKU SBTPDW-01-SB, MPN PDW-01-SB)","url":"https://www.primaryarms.com/sb-tactical-pdw-adjustable-pistol-stabilizing-brace-black","retrieved":"2026-10-18","via":"harvest"}},{"id":"ar15discounts","value":6.75,"unit":"in","stated":"LENGTH: 6.75 in (collapsed), 8.125 in (mid), 9.375 (extended) in","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, SB Tactical SBPDW Pistol Stabilizing Brace - AR - Black (PDW-01-SB)","url":"https://ar15discounts.com/products/sb-tactical-sbpdw-pistol-stabilizing-brace-ar-black/","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"sheet","reason":"The maker's sheet; two sellers state the same figure."},"note":"Every page gives 6.75 in collapsed and none says from where. The photos don't bear it out as the length behind the receiver: on the maker's photo of the pistol the brace's rear stands 7.24 in behind the receiver's rear face (rear_behind_receiver_face), and in its side photo of the assembly alone the same span reads 7.26 in by the thread's own diameter; from the castle nut's rear face it is 4.5, from the thread's front end 7.7. The model's seat is the photo's (butt_behind_pin_pos1); this figure is kept as published and used for the step between positions only (position_step on the receiver extension), where the datum falls out."},"length_mid":{"label":"Length at the middle position (one seller's)","kind":"length","measurements":[{"id":"ar15discounts","value":8.125,"unit":"in","stated":"LENGTH: 6.75 in (collapsed), 8.125 in (mid), 9.375 (extended) in","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, SB Tactical SBPDW Pistol Stabilizing Brace - AR - Black (PDW-01-SB)","url":"https://ar15discounts.com/products/sb-tactical-sbpdw-pistol-stabilizing-brace-ar-black/","retrieved":"2026-10-18","via":"harvest"},"note":"1.375 in out from collapsed and 1.25 short of extended: the two steps differ by 1/8 in, which no other page says."}]},"length_extended":{"label":"Length extended","kind":"length","measurements":[{"id":"sheet","value":9.4,"unit":"in","stated":"Length: 6.75\" Collapsed 9.4\" Extended","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBPDW specification sheet (REV FEBRUARY 2022), linked from the product page as 'SBPDW Specification Sheet'","url":"https://www.sb-tactical.com/wp-content/uploads/SBPDW_3422-1.pdf","retrieved":"2026-10-18","via":"harvest"}},{"id":"primary-arms","value":9.375,"unit":"in","stated":"across the brace's 3 positions, from 6.75\" collapsed to 9.375\" extended","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, SB Tactical SBPDW AR Pistol Brace (SKU SBTPDW-01-SB, MPN PDW-01-SB)","url":"https://www.primaryarms.com/sb-tactical-pdw-adjustable-pistol-stabilizing-brace-black","retrieved":"2026-10-18","via":"harvest"}},{"id":"ar15discounts","value":9.375,"unit":"in","stated":"LENGTH: 6.75 in (collapsed), 8.125 in (mid), 9.375 (extended) in","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, SB Tactical SBPDW Pistol Stabilizing Brace - AR - Black (PDW-01-SB)","url":"https://ar15discounts.com/products/sb-tactical-sbpdw-pistol-stabilizing-brace-ar-black/","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"primary-arms","reason":"9 3/8 in, which the maker's sheet rounds to 9.4 (inside half its last digit); two sellers state it in full."}},"height":{"label":"Height","kind":"length","measurements":[{"id":"photo","value":5.02,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sb-tactical-sbpdw c303ad6a4930 (SB Tactical sbpdw-side-product_image.jpg, the assembly alone from the right, 2000 x 1500)","scaleRef":"the housing's front face (column 1556) to the cuff's rear (column 331) = rear_behind_receiver_face, 7.24 in: 169.2 px/in; the thread's top edge 99.5 px above the axis the castle nut's notches are symmetric about agrees (168.4 px/in for the standard's 1.181 in thread)","method":"rows 322 (the strap's top over the cuff) to 1172 (the cuff's foot): 850 px","via":"harvest"}},{"id":"installed","value":5.06,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/sb-tactical-sbpdw 16bd2ee83240 (SB Tactical sbpdw-installed_2-product_image.jpg, collapsed on an AR pistol, left side, 2000 x 1500)","scaleRef":"the pivot pin's head (871.3, 707.5) to the receiver's rear face where the housing begins (column 1357): 7.5 in (std.ar15.pin_spacing + the receiver's rear face behind the takedown pin): 64.8 px/in","method":"rows 585 to 913 at the cuff (columns 1740 to 1800)","via":"harvest"}}],"adopt":{"from":"photo","reason":"The larger photo; the installed one agrees within its ±."},"note":"No page states it. Read on the maker's side photo from the strap's top over the cuff to the cuff's foot."},"width":{"label":"Width (the cuff's widest)","kind":"length","measurements":[{"id":"sheet","value":2.25,"unit":"in","stated":"Width (max): 2.25\"","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBPDW specification sheet (REV FEBRUARY 2022), linked from the product page as 'SBPDW Specification Sheet'","url":"https://www.sb-tactical.com/wp-content/uploads/SBPDW_3422-1.pdf","retrieved":"2026-10-18","via":"harvest"}},{"id":"ar15discounts","value":2.25,"unit":"in","stated":"WIDTH [MAX]: 2.25 in","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, SB Tactical SBPDW Pistol Stabilizing Brace - AR - Black (PDW-01-SB)","url":"https://ar15discounts.com/products/sb-tactical-sbpdw-pistol-stabilizing-brace-ar-black/","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"sheet","reason":"The maker's sheet; a seller states the same."}},"strap_width":{"label":"The strap's width","kind":"length","measurements":[{"id":"sheet","value":1,"unit":"in","pm":0.05,"stated":"Strap Width: 1\"","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBPDW specification sheet (REV FEBRUARY 2022), linked from the product page as 'SBPDW Specification Sheet'","url":"https://www.sb-tactical.com/wp-content/uploads/SBPDW_3422-1.pdf","retrieved":"2026-10-18","via":"harvest"}},{"id":"ar15discounts","value":1,"unit":"in","pm":0.05,"stated":"STRAP WIDTH: 1 in","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, SB Tactical SBPDW Pistol Stabilizing Brace - AR - Black (PDW-01-SB)","url":"https://ar15discounts.com/products/sb-tactical-sbpdw-pistol-stabilizing-brace-ar-black/","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"sheet","reason":"The maker's sheet; a seller states the same."}},"kit_weight":{"label":"Weight of the whole SBPDW as sold: the brace, its housing and its receiver extension","kind":"mass","measurements":[{"id":"sheet","value":18.14,"unit":"oz","stated":"Weight: 18.14oz","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBPDW specification sheet (REV FEBRUARY 2022), linked from the product page as 'SBPDW Specification Sheet'","url":"https://www.sb-tactical.com/wp-content/uploads/SBPDW_3422-1.pdf","retrieved":"2026-10-18","via":"harvest"}},{"id":"page","value":19.5,"unit":"oz","stated":"Weight 19.5 oz","source":{"type":"spec","publisher":"manufacturer","name":"SB Tactical, SBPDW® product page (Specifications tab)","url":"https://www.sb-tactical.com/product/sbpdw/","retrieved":"2026-10-18","via":"harvest"}},{"id":"primary-arms","value":18.14,"unit":"oz","stated":"Weight: 18.14 oz","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, SB Tactical SBPDW AR Pistol Brace (SKU SBTPDW-01-SB, MPN PDW-01-SB)","url":"https://www.primaryarms.com/sb-tactical-pdw-adjustable-pistol-stabilizing-brace-black","retrieved":"2026-10-18","via":"harvest"}},{"id":"ar15discounts","value":18.14,"unit":"oz","stated":"WEIGHT: 18.14 oz","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, SB Tactical SBPDW Pistol Stabilizing Brace - AR - Black (PDW-01-SB)","url":"https://ar15discounts.com/products/sb-tactical-sbpdw-pistol-stabilizing-brace-ar-black/","retrieved":"2026-10-18","via":"harvest"}},{"id":"ar15discounts-shop","value":8.224,"unit":"oz","stated":"Additional information Weight 8.224 oz Dimensions 9.375 × 2.25 × 2.5 in","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, SB Tactical SBPDW Pistol Stabilizing Brace - AR - Black (PDW-01-SB)","url":"https://ar15discounts.com/products/sb-tactical-sbpdw-pistol-stabilizing-brace-ar-black/","retrieved":"2026-10-18","via":"harvest"},"note":"The shop's shipping fields; not the product's weight."}],"adopt":{"from":"sheet","reason":"The maker's own sheet, to the hundredth, and two sellers state the same; the page's 19.5 oz is the maker's too and is kept beside it: which is newer, or what else it counts, isn't said."},"note":"Every figure is of the assembly. The maker's page's spec tab says 19.5 oz today; its sheet and two sellers 18.14. AR15Discounts' shop field 'Weight 8.224 oz' sits beside 'Dimensions 9.375 × 2.25 × 2.5 in', a shipping record, and is less than the aluminium of the tube and housing alone would leave for the brace."},"weight":{"label":"Weight (the brace alone: what the whole assembly weighs less its receiver extension and housing)","kind":"mass","measurements":[{"id":"derived","value":9.89,"unit":"oz","pm":1.6,"source":{"type":"derived","expr":"{.kit_weight} - {sb-tactical-sbpdw-receiver-extension.weight}","via":"harvest"}}],"note":"No page weighs the brace apart from its tube. Worked out: the published weight of the whole, less the receiver extension's and housing's aluminium as drawn (sb-tactical-sbpdw-receiver-extension.weight). Its ± is that figure's and the 1.4 oz between the maker's two weights of the whole."},"tube_axis_below_top":{"label":"Tube axis below the brace's top (the strap's top over the cuff)","kind":"length","measurements":[{"id":"photo","value":1.067,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sb-tactical-sbpdw c303ad6a4930 (the assembly alone from the right)","scaleRef":"169.2 px/in (height)","method":"the axis at row 502.5, midway between the castle nut's two notches seen on this side (rows 457 and 548, each 22.5° off the horizontal on a ring of eight); the top at row 322: 180.5 px. The thread's top edge (row 403) less the standard thread's radius puts the axis at 502.7","via":"harvest"}}]},"rear_behind_receiver_face":{"label":"The brace's rear behind the receiver's rear face, collapsed on a rifle","kind":"length","measurements":[{"id":"installed","value":7.24,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/sb-tactical-sbpdw 16bd2ee83240 (collapsed on an AR pistol, left side, 2000 x 1500)","scaleRef":"the pivot pin's head (871.3, 707.5; the takedown pin is under the brace's rod in this view) to the receiver's rear face where the housing begins (column 1357 ± 3): 7.5 in = std.ar15.pin_spacing + 1.125 (std.ar15.receiver_rear_x): 64.8 px/in","method":"column 1357 to the brace's rearmost (column 1826): 469 px. Checks: the maker's right side view of the pistol with the brace out (b180728537b9, at its own scale, 59.3 px/in by its two pins) has the tube between the castle nut and the brace 2.65 in longer than this one, for the published 2.625 in of travel; and the side photo of the assembly alone, scaled by the thread's diameter, reads 7.26 for the same span","via":"harvest"}}],"note":"Where the housing's front bears on the receiver, in the end plate's place (\"The end plate and castle nut are integral to the assembly\")."},"butt_behind_pin_pos1":{"label":"Rear behind the takedown pin at its first position (collapsed), on its own tube","kind":"length","measurements":[{"id":"installed","value":8.365,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{.rear_behind_receiver_face} - {std.ar15.receiver_rear_x}","via":"harvest"},"note":"The installed photo's reading behind the receiver's rear face, which the Army's drawing puts 1.125 in behind the takedown pin."}]},"rod_spacing":{"label":"The guide rods' spacing, centre to centre","kind":"length","measurements":[{"id":"ar15discounts","value":1.175,"unit":"in","stated":"Space between rods is 1.175″","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, SB Tactical SBPDW Pistol Stabilizing Brace - AR - Black (PDW-01-SB)","url":"https://ar15discounts.com/products/sb-tactical-sbpdw-pistol-stabilizing-brace-ar-black/","retrieved":"2026-10-18","via":"harvest"},"note":"One seller's figure: taken as centre to centre, the two rods either side of the tube's vertical plane."}]},"rod_d":{"label":"A guide rod's diameter","kind":"length","measurements":[{"id":"left-photo","value":0.334,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sb-tactical-sbpdw 73787978fd88 (Primary Arms SBTPDW-01-SB, the assembly alone from the left, 1920 x 1280)","scaleRef":"131 px/in: the castle nut's notches seen on this side are 35 px either side of the axis (0.267 in on the nut's 1.394 in, at 22.5°); the thread's top edge then gives 1.198 in for the standard's 1.181","method":"the near rod's edges against the far rod's top (a lit line between them, rows 546 to 548) and the background (row 591): 43 px","via":"harvest"}},{"id":"right-photo","value":0.373,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sb-tactical-sbpdw c303ad6a4930 (the assembly alone from the right)","scaleRef":"169.2 px/in","method":"the near rod, rows 627 to 690: its upper edge lies along the far rod with no line between them, picked where the shading changes","via":"harvest"}}],"adopt":{"from":"left-photo","reason":"Both its edges are lines in the photo; the right view's upper edge is a change of shade."}},"rod_below_axis":{"label":"The guide rods' axis below the tube's axis","kind":"length","measurements":[{"id":"right-photo","value":0.78,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sb-tactical-sbpdw c303ad6a4930 (the assembly alone from the right)","scaleRef":"169.2 px/in; the axis at row 502.5","method":"the near rod's centre at row 658.5, the far rod's at 610 (its top at 582 less half the rod), the middle of the two 634: 132 px","via":"harvest"}},{"id":"left-photo","value":0.83,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sb-tactical-sbpdw 73787978fd88 (the assembly alone from the left)","scaleRef":"131 px/in; the axis at row 451, midway between the castle nut's notches","method":"the near rod's centre at row 569.5, the far rod's at 539.5, the middle 554.5: 103.5 px","via":"harvest"}}],"adopt":{"from":"right-photo","reason":"The photo the outline is traced from, at the larger scale; the left view's reading is inside the two ±."},"note":"The rods are level: in each side view the near rod reads lower and the far one higher, by a camera above the axis (the right view's near rod 0.92 in down, its far one 0.64; the left view's 0.95 and 0.71). The rod on the left is the near one in one view and the far one in the other, so neither stands higher; each reading here is the middle of the two."},"rod_front_ahead_of_butt":{"label":"The rods' front ends ahead of the brace's rear, collapsed on a rifle","kind":"length","measurements":[{"id":"installed","value":8.63,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/sb-tactical-sbpdw 16bd2ee83240 (collapsed on an AR pistol, left side)","scaleRef":"64.8 px/in (rear_behind_receiver_face)","method":"the rod's front end at column 1267, 90 px ahead of the receiver's rear face (1.39 in), with the brace's rear 7.24 in behind it","via":"harvest"}},{"id":"right-photo","value":8.92,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sb-tactical-sbpdw c303ad6a4930 (the assembly alone from the right)","scaleRef":"169.2 px/in","method":"the near rod's front end at column 1835, the brace's rear at 331","via":"harvest"},"note":"Off the rifle."}],"adopt":{"from":"installed","reason":"On the rifle, collapsed: the brace's first position, where the catalog draws it."},"note":"On the rifle the rods run past the housing beside the lower receiver's rear, over its takedown pin's head (the maker's photo of the pistol from the left). Off the rifle the maker's two side photos have them further forward (8.92 and 9.5 in ahead of the brace's rear): how the rods are held in the brace and the housing isn't seen."},"rod_enters_strut_ahead_of_butt":{"label":"Where the rods go into the brace's strut, ahead of its rear","kind":"length","measurements":[{"id":"photo","value":2.03,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/sb-tactical-sbpdw c303ad6a4930 (the assembly alone from the right)","scaleRef":"169.2 px/in","method":"the strut's front edge where the near rod meets it, column 674 (rows 640 to 700)","via":"harvest"}}]},"bore_d":{"label":"The bore the tube's rear runs in","kind":"length","measurements":[{"id":"assumed","value":1.166,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the brace's body slides over its own tube (sb-tactical-sbpdw-receiver-extension.tube_od, 1.146) and no view on file shows the bore's mouth square; drawn 0.02 in over the tube.","via":"harvest"}}]},"cuff_length":{"label":"The cuff's length along the tube (its flaps, from the rear to their front edge)","kind":"length","measurements":[{"id":"photo","value":1.38,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sb-tactical-sbpdw c303ad6a4930 (the assembly alone from the right)","scaleRef":"169.2 px/in","method":"the brace's rear (column 331) to the cuff's front edge under the strap's band (column 565, rows 700 to 1100)","via":"harvest"}}]},"body_width":{"label":"The brace's body round the tube, ahead of the cuff: its width","kind":"length","measurements":[{"id":"assumed","value":1.45,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file is square across it. In the two obliques from above (f1b3345f7383, 0d379b324f10) the body over the tube is about as wide as the castle nut (1.39 in) and a little wider; drawn so, with a wall of 0.14 in each side of the bore.","via":"harvest"}}]},"strap_centre_ahead_of_butt":{"label":"The strap's band round the cuff: its middle ahead of the brace's rear","kind":"length","measurements":[{"id":"photo","value":0.72,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sb-tactical-sbpdw c303ad6a4930 (the assembly alone from the right)","scaleRef":"169.2 px/in","method":"the band's two edges on the cuff's side, columns 360 and 545 (rows 400 to 1100), their middle at 452.5. The band reads 1.09 in across there for the published 1 in: the cuff's side stands 1.1 in nearer the lens than the axis the scale is taken on, and the band's edges are folded","via":"harvest"}}]},"strap_thickness":{"label":"The strap's thickness over the cuff","kind":"length","measurements":[{"id":"assumed","value":0.06,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the strap's top over the cuff stands about 12 px (0.07 in) over the cuff's own top in the side photo, which is the band's two layers where it is doubled under its buckle and one elsewhere; drawn one layer of 0.06 in all round.","via":"harvest"}}]}}},{"subject":"sb-tactical-sbpdw-receiver-extension","title":"SB Tactical SBPDW receiver extension, housing and integral castle nut (the SBPDW's own tube; not sold alone)","dimensions":{"tube_front_behind_pin":{"label":"The tube's front face behind the takedown pin (how far it screws in)","kind":"length","measurements":[{"id":"std","value":0.669,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"-{std.receiver_extension.front_face_x}","via":"harvest"},"note":"The Army's drawings: screwed in until its edge stands over the buffer retainer's shoulder. The maker: \"Depress the buffer retainer pin and continue threading the tube until the buffer retainer pin is captured.\""},{"id":"photo","value":0.682,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sb-tactical-sbpdw c303ad6a4930 (SB Tactical sbpdw-side-product_image.jpg, the assembly alone from the right)","scaleRef":"169.2 px/in (see the file's header)","method":"the thread's front end (column 1631) 75 px ahead of the housing's front face (column 1556), which bears on the receiver's rear face 1.125 in behind the pin","via":"harvest"}}],"adopt":{"from":"std","reason":"The drawing that sets it; the maker's photo agrees within its ±."}},"tube_od":{"label":"The tube's outside diameter (behind the castle nut)","kind":"length","measurements":[{"id":"photo","value":1.141,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sb-tactical-sbpdw c303ad6a4930 (the assembly alone from the right)","scaleRef":"169.2 px/in","method":"the tube's top edge between the nut and the brace (row 406, columns 880 to 1080) 96.5 px over the axis; its lower edge is behind the rods","via":"harvest"}}],"note":"No page states it. Read on the side photo; it slides in the brace's body, so its brace's bore is drawn over it (sb-tactical-sbpdw-brace.bore_d)."},"bore_d":{"label":"The tube's bore","kind":"length","measurements":[{"id":"std","value":1,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.receiver_extension.bore_d}","via":"harvest"},"note":"The Army's drawing's bore, what a buffer runs in; the maker: \"SBPDW is compatible with mil-spec receivers and carbine length buffers and springs\". No page gives this tube's own."}]},"bore_depth":{"label":"The tube's depth (its bore, from its front face to its rear wall)","kind":"length","measurements":[{"id":"ar15discounts","value":6.92,"unit":"in","pm":0.0005,"stated":"Depth of the tube is 6.920″","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, SB Tactical SBPDW Pistol Stabilizing Brace - AR - Black (PDW-01-SB)","url":"https://ar15discounts.com/products/sb-tactical-sbpdw-pistol-stabilizing-brace-ar-black/","retrieved":"2026-10-18","via":"harvest"},"note":"One seller's figure, taken as the bore's depth from the tube's front face: what a buffer and its spring have. BCM's carbine tube as the catalog draws it has 7.18 in."}]},"rear_wall":{"label":"The tube's rear wall","kind":"length","measurements":[{"id":"assumed","value":0.072,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the tube's rear end is inside the brace in every photo on file. Drawn as the reference model's mil-spec carbine tube's (std.receiver_extension.carbine_rear_wall, 0.072 in).","via":"harvest"}}]},"tube_length":{"label":"The tube's length (its front face to its rear)","kind":"length","measurements":[{"id":"derived","value":6.992,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.bore_depth} + {.rear_wall}","via":"harvest"}}]},"position_step":{"label":"The brace's step between its positions","kind":"length","measurements":[{"id":"derived","value":1.3125,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"({sb-tactical-sbpdw-brace.length_extended} - {sb-tactical-sbpdw-brace.length}) / 2","via":"harvest"}}],"note":"Three positions (\"3-position adjustable\"). Half the published travel from collapsed to extended: AR15Discounts' middle position is 1.375 in out and 1.25 short of extended, one seller's figures; the catalog moves by one step."},"housing_front_behind_pin":{"label":"The housing's front face behind the takedown pin","kind":"length","measurements":[{"id":"std","value":1.125,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"-{std.ar15.receiver_rear_x}","via":"harvest"}}],"note":"It bears on the receiver's rear face where an end plate does (AR15Discounts: \"The end plate and castle nut are integral to the assembly\")."},"housing_length":{"label":"The housing's length (its top, from its front face to the castle nut)","kind":"length","measurements":[{"id":"photo","value":2.02,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sb-tactical-sbpdw c303ad6a4930 (the assembly alone from the right)","scaleRef":"169.2 px/in","method":"columns 1556 (its front face) to 1215 (the seam with the castle nut, a lit line 1210 to 1219 at row 400): 341 px","via":"harvest"}}]},"housing_od":{"label":"The housing's diameter round the tube","kind":"length","measurements":[{"id":"photo","value":1.418,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sb-tactical-sbpdw c303ad6a4930 (the assembly alone from the right)","scaleRef":"169.2 px/in","method":"its top edge (row 382.5, columns 1230 to 1540) 120 px over the axis","via":"harvest"}}]},"housing_bore":{"label":"The housing's bore (the tube passes through it)","kind":"length","measurements":[{"id":"assumed","value":1.1813,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the tube goes into the housing thread first (\"With the tube inserted into the housing\"), so the bore takes the thread's crests (std.receiver_extension.thread_major_d); no view on file shows its mouth square.","via":"harvest"}}]},"rod_bore_d":{"label":"The housing's bores the brace's rods run in","kind":"length","measurements":[{"id":"assumed","value":0.35,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the rods (sb-tactical-sbpdw-brace.rod_d, 0.334 in) slide in them; drawn 0.016 in over the rod. The front oblique photo (6020c5e68ca5) shows the two rods coming out of the housing's front face at its lower corners.","via":"harvest"}}]},"ear_wall":{"label":"The housing's wall outside each rod's bore","kind":"length","measurements":[{"id":"assumed","value":0.09,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file is square to the housing's front or from below; the front oblique photo (6020c5e68ca5) shows a thin wall round each rod at the housing's lower corners.","via":"harvest"}}]},"nut_length":{"label":"The integral castle nut's length","kind":"length","measurements":[{"id":"photo","value":0.7,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sb-tactical-sbpdw c303ad6a4930 (the assembly alone from the right)","scaleRef":"169.2 px/in","method":"columns 1215 (its seam with the housing) to 1097 (its rear face): 118 px","via":"harvest"}}]},"nut_od":{"label":"The integral castle nut's diameter","kind":"length","measurements":[{"id":"photo","value":1.389,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sb-tactical-sbpdw c303ad6a4930 (the assembly alone from the right)","scaleRef":"169.2 px/in","method":"its top edge (row 385, columns 1100 to 1200) 117.5 px over the axis","via":"harvest"}}]},"nut_notch_width":{"label":"The castle nut's notches: width","kind":"length","measurements":[{"id":"photo","value":0.11,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sb-tactical-sbpdw c303ad6a4930 (the assembly alone from the right)","scaleRef":"169.2 px/in","method":"each of the two notches on this side, 17 px across, seen 22.5° off square (divided by cos 22.5°)","via":"harvest"}}]},"nut_notch_depth":{"label":"The castle nut's notches: depth from its rear face","kind":"length","measurements":[{"id":"photo","value":0.2,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sb-tactical-sbpdw c303ad6a4930 (the assembly alone from the right)","scaleRef":"169.2 px/in","method":"columns 1097 to 1130: 33 px","via":"harvest"}}]},"nut_notch_count":{"label":"The castle nut's notches: how many","kind":"count","measurements":[{"id":"photos","value":8,"unit":"count","source":{"type":"photo","photo":"references/sb-tactical-sbpdw c303ad6a4930, 73787978fd88, c3847cdcc54b","scaleRef":"a count","method":"six seen, at 22.5°, 67.5°, 112.5° off the horizontal each side; the pattern's two at the bottom hidden","via":"harvest"}}],"note":"Counted on the views that show them: two on the right side, each 0.267 in off the axis (22.5° on the nut's radius: rows 457 and 548 in c303ad6a4930), two on the left the same (73787978fd88), and two at the top either side of the middle in the view from behind (c3847cdcc54b). Eight at 45° turned 22.5° off the vertical puts a notch at each of those six places; the two at the bottom are behind the housing's lower part in every view."},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"metal","value":8.25,"unit":"oz","pm":0.9,"source":{"type":"derived","expr":"(0.785398163 * ({.tube_od} * {.tube_od} - {.bore_d} * {.bore_d}) * ({.tube_length} - {std.receiver_extension.thread_length}) + 0.785398163 * ({std.receiver_extension.thread_minor_d} * {std.receiver_extension.thread_minor_d} - {.bore_d} * {.bore_d}) * {std.receiver_extension.thread_length} + 0.785398163 * {.bore_d} * {.bore_d} * {.rear_wall} + 0.785398163 * ({.nut_od} * {.nut_od} - {.tube_od} * {.tube_od}) * {.nut_length} - {.nut_notch_count} * {.nut_notch_width} * {.nut_notch_depth} * ({.nut_od} - {.tube_od}) / 2 + ({sb-tactical-sbpdw-brace.rod_spacing} + {sb-tactical-sbpdw-brace.rod_d} + 2 * {.ear_wall}) * {.housing_bottom_below_axis} * {.housing_length} - 0.392699082 * {.housing_bore} * {.housing_bore} * {.housing_length} + 0.392699082 * ({.housing_od} * {.housing_od} - {.housing_bore} * {.housing_bore}) * {.housing_length} - 2 * 0.785398163 * {.rod_bore_d} * {.rod_bore_d} * {.housing_length}) * {std.density.aluminium}","via":"harvest"}}],"note":"No page weighs the tube, nut and housing apart from the brace (the maker: \"Castle nut / receiver extension is aluminum\"; the housing's metal isn't stated, and it is drawn as aluminium). Worked out from the sizes the model is drawn from: the tube (its wall over the bore, its threaded front, its rear wall), the nut less its notches, and the housing (the block from its foot up to the axis, as wide as the rods' bosses, less the lower half of its bore and the rods' bores, and the round over the tube's upper half), as aluminium (std.density.aluminium). The model holds 0.35 cubic inches more (0.55 oz: the housing's tail under the nut, its two levers, the thread's flanks over their roots), which the ± covers."},"housing_bottom_below_axis":{"label":"The housing's underside below the tube's axis","kind":"length","measurements":[{"id":"photo","value":1.26,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sb-tactical-sbpdw c303ad6a4930 (the assembly alone from the right)","scaleRef":"169.2 px/in","method":"its lower edge between the levers (row 716, columns 1330 to 1450) 213.5 px under the axis","via":"harvest"}}]},"lever_width":{"label":"The takedown lever's width across the rifle","kind":"length","measurements":[{"id":"assumed","value":0.3,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the lever hangs from the housing's underside at its rear (its side seen square in c303ad6a4930); the obliques from behind (0d379b324f10, f1b3345f7383) show a flat tab about a third of the housing's width, and no view is square across it.","via":"harvest"}}]},"latch_width":{"label":"The adjustment latch's width across the rifle","kind":"length","measurements":[{"id":"assumed","value":0.35,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the ribbed latch under the housing's middle is seen square from the side only; the obliques show it a little wider than the takedown lever.","via":"harvest"}}]}}},{"subject":"scalarworks-leap-01-micro-142","title":"Scalarworks LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.42 in (SW0100)","dimensions":{"optical_axis_above_rail":{"label":"Optical axis above the rail's top, with an Aimpoint Micro T-2 on it (the maker's height)","kind":"length","measurements":[{"id":"page","value":1.42,"unit":"in","stated":"Optic center height over rail SW0100 : 1.42\" SW0110 : 1.57\" SW0120 : 1.93\"","source":{"type":"spec","publisher":"manufacturer","name":"Scalarworks, LEAP/01 (product page, SPECIFICATIONS)","url":"https://scalarworks.com/shop/quick-detach-mounts/leap-01/","retrieved":"2026-11-03","via":"harvest"},"note":"MidwayUSA's page: \"Note: Height measurement is from the top of the rail to the center of the optic.\""},{"id":"drawing","value":1.42,"unit":"in","stated":"1.42” OPTIC CENTER","source":{"type":"spec","publisher":"manufacturer","name":"Scalarworks, the technical drawing of SW0100 in the LEAP/01 page's gallery for the 1.42 in height (references/scalarworks-leap-01-micro-142 c08b4e430885)","url":"https://scalarworks.com/wp-content/uploads/scalarworks-SW0100-diagram-A.png","retrieved":"2026-11-03","via":"harvest"},"note":"From the extension line through the clamp's shaft (the rail's top) to the T-2's axis."},{"id":"wing","value":1.42,"unit":"in","stated":"Center Height Over Rail: Absolute Co-Witness : 1.42\" (36mm) Lower 1/3 : 1.57\" (40mm)","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Scalarworks LEAP Aimpoint Micro Mount","url":"https://www.wingtactical.com/accessories/optics-sights/optic-sight-mounts/scalarworks-leap-aimpoint-micro-mount/","retrieved":"2026-11-03","via":"harvest"}},{"id":"as-drawn","value":1.413,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-142 c08b4e430885 (Scalarworks' technical drawing of SW0100: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top): 340.4 px/in, as the other heights' drawings, the rail's top at row 1091 and its middle at column 600.25. From the clamp up to the body's shoulders the drawing is the 1.57 in's stroke for stroke; above them it is the 1.57 in's moved down 53 px","method":"the red dot's centroid (row 610.15) above the extension line (row 1091): 480.85 px","via":"harvest"},"note":"0.007 in under the stated figure: the 1.42 in's own lines are at 338.6 px/in."}],"adopt":{"from":"page","reason":"The maker's stated centre height, the figure a buyer compares and the category's (D101); its drawing's lines put the axis 0.007 in lower at the scale its rail gives, inside the two readings' ±."},"note":"The maker names no dot in the sentence (\"Optic center height over rail\"); the page is \"LEAP/01 Premium Aimpoint Micro T-2 mounts.\" and its drawing of this height draws a T-2 on the mount: the height is the T-2's. Its co-witness, in the same table: \"SW0100 : Absolute\". The page's advice: \"Choose 1.42″ height if: You value a tight cheek weld in all shooting positions. You want an absolute co-witness with backup sights. You don’t shoot with a top-rail mounted light or laser.\""},"window_top_above_rail":{"label":"Top of the window through the mount (end to end), above the rail's top","kind":"length","measurements":[{"id":"drawing","value":17.5,"unit":"mm","stated":"17.5MM","source":{"type":"spec","publisher":"manufacturer","name":"Scalarworks, the technical drawing of SW0100 in the LEAP/01 page's gallery for the 1.42 in height (references/scalarworks-leap-01-micro-142 c08b4e430885)","url":"https://scalarworks.com/wp-content/uploads/scalarworks-SW0100-diagram-A.png","retrieved":"2026-11-03","via":"harvest"},"note":"From the same extension line as the 1.42 in to the top of the window's throat (the inner of the two outlines drawn round it)."},{"id":"as-drawn","value":0.6948,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-142 c08b4e430885 (Scalarworks' technical drawing of SW0100: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top): 340.4 px/in, as the other heights' drawings, the rail's top at row 1091 and its middle at column 600.25. From the clamp up to the body's shoulders the drawing is the 1.57 in's stroke for stroke; above them it is the 1.57 in's moved down 53 px","method":"the throat's top stroke (row 854.5) above the extension line (1091): 236.5 px","via":"harvest"},"note":"17.65 mm, two pixels off: the check of the drawing's scale."}],"adopt":{"from":"drawing","reason":"The maker's stated dimension; its lines read the same at the scale the rail gives."},"note":"Here the window's throat is 39 px (0.115 in) under the deck's floor, as in the 1.57 in's drawing: the drawings' window figures step with the heights but for the 1.93 in's, whose deck is 0.75 mm thicker over its window."},"deck_above_rail":{"label":"The deck's floor (where the dot's base sits) above the rail's top","kind":"length","measurements":[{"id":"less-t2","value":0.831,"unit":"in","pm":0.037,"source":{"type":"derived","expr":"{.optical_axis_above_rail} - {aimpoint-micro-t-2.axis_above_base}","via":"harvest"},"note":"1.42 in less the T-2's 0.589 in."},{"id":"drawing","value":0.8093,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-142 c08b4e430885 (Scalarworks' technical drawing of SW0100: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top): 340.4 px/in, as the other heights' drawings, the rail's top at row 1091 and its middle at column 600.25. From the clamp up to the body's shoulders the drawing is the 1.57 in's stroke for stroke; above them it is the 1.57 in's moved down 53 px","method":"the stroke the T-2's foot stands on between the rims (row 815.5) above the extension line (1091): 275.5 px. The T-2's axis is 205.35 px over it: 0.603 in, inside the 0.589 ± 0.037 the T-2's ledger has","via":"harvest"}}],"adopt":{"from":"less-t2","reason":"The category's figure (D101): the maker's axis height for the T-2 less the T-2's own axis over its base, which puts the T-2 at the maker's 1.42 in. The maker's drawing has the floor 0.022 in lower, inside the two readings' ±."},"note":"A floor between two rims that run the deck's whole length, the T-2's foot down on it between them and its housing on the rims' tops (the drawing; the deck from above in Wing Tactical's photo of a LEAP/01, filed with the 1.57 in). The maker states only the axis's height, for the T-2: the floor is that less the T-2's axis over its base (D101). The drawing puts it there within the two readings' ±."},"rim_top_above_rail":{"label":"The deck's two rims, their tops above the rail's top","kind":"length","measurements":[{"id":"drawing","value":0.8887,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-142 c08b4e430885 (Scalarworks' technical drawing of SW0100: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top): 340.4 px/in, as the other heights' drawings, the rail's top at row 1091 and its middle at column 600.25. From the clamp up to the body's shoulders the drawing is the 1.57 in's stroke for stroke; above them it is the 1.57 in's moved down 53 px","method":"the rims' top stroke (row 788.5) above the extension line (1091): 302.5 px","via":"harvest"}},{"id":"side-photo","value":0.904,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-142 351188c51fd3 (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.42-side-SW0100.jpg: SW0100 alone on a rail section, straight left side, 1200 x 1200)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 306.5 and 889.6 (the gaps' edges on rows 706 to 724), six pitches apart (std.picatinny.slot_pitch): 97.18 px a pitch, 246.65 px/in at the rail's middle; the teeth's tops on row 700 (the white ground shows through the slots down to their floors: the photo is level)","method":"the mount's top edge (row 477, from column 340 to 760) above the teeth's tops: 223 px","via":"harvest"},"note":"1.7% over the drawing, as the other heights' photos read 1.3%: the near face stands nearer the lens than the rail's middle."}],"adopt":{"from":"drawing","reason":"The maker's drawing at the scale its rail gives; the photo reads the near face large."},"note":"What the side views show as the mount's top. Not drawn above the deck's floor: every Micro dot on file is drawn with its base as wide as its housing (the part's approximations)."},"deck_x":{"label":"The footprint's middle along the deck, ahead of the wheel's shaft","kind":"length","measurements":[{"id":"side-photo","value":0.195,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-142 351188c51fd3 (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.42-side-SW0100.jpg: SW0100 alone on a rail section, straight left side, 1200 x 1200)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 306.5 and 889.6 (the gaps' edges on rows 706 to 724), six pitches apart (std.picatinny.slot_pitch): 97.18 px a pitch, 246.65 px/in at the rail's middle; the teeth's tops on row 700 (the white ground shows through the slots down to their floors: the photo is level)","method":"the middle of the rims' flat top, between the step at its front end (column 340) and where its rear end scoops down (760): column 550, 48.05 px ahead of the wheel's shaft (column 598.05, the slot midway)","via":"harvest"}},{"id":"bundle","value":0.215,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-142 6376f16e34d6 (Scalarworks, scalarworks-leap-01-aimpoint-micro-t2-bundle-1.42-side-SW0100-T2.jpg: the mount with a Micro T-2 on it, straight left side)","scaleRef":"the rail section's slots at columns 329.5 and 865.5, six pitches apart: 89.33 px a pitch, 226.7 px/in; the shaft in the slot midway, column 597.5","method":"the T-2's rubber covers, lids closed, from column 198 to about 886 at its axis: their middle 0.245 in ahead of the shaft; the T-2's model has its footprint's middle 0.03 in behind its covers' middle","via":"harvest"},"note":"The check: where the T-2 screwed to the footprint has its own footprint's middle."}],"adopt":{"from":"side-photo","reason":"The mount's own deck; the T-2 on it in the same set-up puts its footprint's middle 0.02 in further forward, within both ±."},"note":"Further back than on the 1.57 in (0.28) and the 1.93 in (0.36): the legs lean forward, and the lower mount's deck stands less far ahead of its clamp."},"mount_length":{"label":"The clamp's length along the rail, at its foot","kind":"length","measurements":[{"id":"side-photo","value":1.553,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-142 351188c51fd3 (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.42-side-SW0100.jpg: SW0100 alone on a rail section, straight left side, 1200 x 1200)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 306.5 and 889.6 (the gaps' edges on rows 706 to 724), six pitches apart (std.picatinny.slot_pitch): 97.18 px a pitch, 246.65 px/in at the rail's middle; the teeth's tops on row 700 (the white ground shows through the slots down to their floors: the photo is level)","method":"the clamp's foot under the rail's top (row 758), from the front leg's lower end (column 432.0) to the rear face (815): 383 px","via":"harvest"}}]},"clamp_front":{"label":"The clamp's foot, its front end ahead of the wheel's shaft","kind":"length","measurements":[{"id":"side-photo","value":0.673,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-142 351188c51fd3 (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.42-side-SW0100.jpg: SW0100 alone on a rail section, straight left side, 1200 x 1200)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 306.5 and 889.6 (the gaps' edges on rows 706 to 724), six pitches apart (std.picatinny.slot_pitch): 97.18 px a pitch, 246.65 px/in at the rail's middle; the teeth's tops on row 700 (the white ground shows through the slots down to their floors: the photo is level)","method":"the traced outline's foot (profiles.side) ends at column 432.0, 166.05 px ahead of the shaft (598.05)","via":"harvest"}}]},"clamp_rear":{"label":"The clamp's foot, its rear end behind the wheel's shaft","kind":"length","measurements":[{"id":"side-photo","value":0.88,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-142 351188c51fd3 (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.42-side-SW0100.jpg: SW0100 alone on a rail section, straight left side, 1200 x 1200)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 306.5 and 889.6 (the gaps' edges on rows 706 to 724), six pitches apart (std.picatinny.slot_pitch): 97.18 px a pitch, 246.65 px/in at the rail's middle; the teeth's tops on row 700 (the white ground shows through the slots down to their floors: the photo is level)","method":"the rear face, column 815, 216.95 px behind the shaft","via":"harvest"}}]},"length":{"label":"Overall length along the rail","kind":"length","measurements":[{"id":"side-photo","value":2.013,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-142 351188c51fd3 (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.42-side-SW0100.jpg: SW0100 alone on a rail section, straight left side, 1200 x 1200)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 306.5 and 889.6 (the gaps' edges on rows 706 to 724), six pitches apart (std.picatinny.slot_pitch): 97.18 px a pitch, 246.65 px/in at the rail's middle; the teeth's tops on row 700 (the white ground shows through the slots down to their floors: the photo is level)","method":"the deck's front step (column 318.6) to the rear face (815): 496.4 px","via":"harvest"},"note":"As read: the near face reads 1.3 to 1.7% large (rim_top_above_rail)."},{"id":"wing","value":2.06,"unit":"in","stated":"Length: 2.06\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Scalarworks LEAP Aimpoint Micro Mount","url":"https://www.wingtactical.com/accessories/optics-sights/optic-sight-mounts/scalarworks-leap-aimpoint-micro-mount/","retrieved":"2026-11-03","via":"harvest"},"note":"One figure on a page that sells the 1.42 and the 1.57 in; what it spans isn't said. The 1.57 in's photo reads its length (2.088 in) within the 1.3% its near face reads large by; this height's is shorter."}],"adopt":{"from":"side-photo","reason":"This height's own photo; Wing Tactical's one figure for two heights is the 1.57 in's length (its photo agrees with it), not this one's."}},"width":{"label":"Overall width across the clamp","kind":"length","measurements":[{"id":"drawing","value":1.334,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-142 c08b4e430885 (Scalarworks' technical drawing of SW0100: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top): 340.4 px/in, as the other heights' drawings, the rail's top at row 1091 and its middle at column 600.25. From the clamp up to the body's shoulders the drawing is the 1.57 in's stroke for stroke; above them it is the 1.57 in's moved down 53 px","method":"the clamp's two outer faces, the strokes at columns 373.5 and 827.5 (rows 1000 to 1120): 454 px, about column 600.5, the rail's middle","via":"harvest"}},{"id":"wing","value":1.338,"unit":"in","stated":"Width: 1.338\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Scalarworks LEAP Aimpoint Micro Mount","url":"https://www.wingtactical.com/accessories/optics-sights/optic-sight-mounts/scalarworks-leap-aimpoint-micro-mount/","retrieved":"2026-11-03","via":"harvest"},"note":"One figure for a page that sells two heights."}],"adopt":{"from":"drawing","reason":"The maker's drawing of this height; a seller's figure agrees to 0.004 in."},"note":"The maker: \"the Leap mount is symmetrical, protruding less than 7mm from either side of your Picatinny rail.\" (under 1.386 in)."},"body_width":{"label":"The body under the deck, across (its two side walls' outer faces)","kind":"length","measurements":[{"id":"drawing","value":0.94,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-142 c08b4e430885 (Scalarworks' technical drawing of SW0100: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top): 340.4 px/in, as the other heights' drawings, the rail's top at row 1091 and its middle at column 600.25. From the clamp up to the body's shoulders the drawing is the 1.57 in's stroke for stroke; above them it is the 1.57 in's moved down 53 px","method":"the walls' strokes at columns 440.5 and 760.5 (rows 800 to 900): 320 px","via":"harvest"}}]},"clamp_below_rail":{"label":"The clamp's foot below the rail's top","kind":"length","measurements":[{"id":"drawing","value":0.234,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-142 c08b4e430885 (Scalarworks' technical drawing of SW0100: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top): 340.4 px/in, as the other heights' drawings, the rail's top at row 1091 and its middle at column 600.25. From the clamp up to the body's shoulders the drawing is the 1.57 in's stroke for stroke; above them it is the 1.57 in's moved down 53 px","method":"the jaws' feet (row 1170.5) under the extension line (1091): 79.5 px","via":"harvest"}},{"id":"side-photo","value":0.235,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-142 351188c51fd3 (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.42-side-SW0100.jpg: SW0100 alone on a rail section, straight left side, 1200 x 1200)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 306.5 and 889.6 (the gaps' edges on rows 706 to 724), six pitches apart (std.picatinny.slot_pitch): 97.18 px a pitch, 246.65 px/in at the rail's middle; the teeth's tops on row 700 (the white ground shows through the slots down to their floors: the photo is level)","method":"the left jaw's foot (row 758) under the teeth's tops (700): 58 px","via":"harvest"}}],"adopt":{"from":"drawing","reason":"The finer reading; the photo agrees within the two ±."}},"wheel_d":{"label":"ClickDrive wheel, over its teeth","kind":"length","measurements":[{"id":"side-photo","value":0.632,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-142 351188c51fd3 (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.42-side-SW0100.jpg: SW0100 alone on a rail section, straight left side, 1200 x 1200)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 306.5 and 889.6 (the gaps' edges on rows 706 to 724), six pitches apart (std.picatinny.slot_pitch): 97.18 px a pitch, 246.65 px/in at the rail's middle; the teeth's tops on row 700 (the white ground shows through the slots down to their floors: the photo is level)","method":"the teeth's tips 76.25 px above and 79.5 px below the wheel's centre (column 599.25, row 700): 155.75 px","via":"harvest"},"note":"The wheel's face is the nearest thing to the lens: as read, perhaps 1.3% large."}],"note":"Twenty teeth, as on the other heights' (counted on this photo's upper half too: tips about 18 degrees apart)."},"wheel_root_d":{"label":"ClickDrive wheel, at the foot of its teeth","kind":"length","measurements":[{"id":"side-photo","value":0.527,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-142 351188c51fd3 (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.42-side-SW0100.jpg: SW0100 alone on a rail section, straight left side, 1200 x 1200)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 306.5 and 889.6 (the gaps' edges on rows 706 to 724), six pitches apart (std.picatinny.slot_pitch): 97.18 px a pitch, 246.65 px/in at the rail's middle; the teeth's tops on row 700 (the white ground shows through the slots down to their floors: the photo is level)","method":"the valleys between the top teeth, 65 px from the centre","via":"harvest"}}]},"wheel_face_d":{"label":"ClickDrive wheel, the face inside its rim","kind":"length","measurements":[{"id":"side-photo","value":0.57,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-142 351188c51fd3 (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.42-side-SW0100.jpg: SW0100 alone on a rail section, straight left side, 1200 x 1200)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 306.5 and 889.6 (the gaps' edges on rows 706 to 724), six pitches apart (std.picatinny.slot_pitch): 97.18 px a pitch, 246.65 px/in at the rail's middle; the teeth's tops on row 700 (the white ground shows through the slots down to their floors: the photo is level)","method":"the bright ring round the face, columns 529.5 to 670","via":"harvest"}}]},"wheel_hub_d":{"label":"ClickDrive wheel, the socket in its middle","kind":"length","measurements":[{"id":"side-photo","value":0.117,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-142 351188c51fd3 (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.42-side-SW0100.jpg: SW0100 alone on a rail section, straight left side, 1200 x 1200)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 306.5 and 889.6 (the gaps' edges on rows 706 to 724), six pitches apart (std.picatinny.slot_pitch): 97.18 px a pitch, 246.65 px/in at the rail's middle; the teeth's tops on row 700 (the white ground shows through the slots down to their floors: the photo is level)","method":"the dark hole at the wheel's middle, columns 585.5 to 614.25","via":"harvest"}}]},"wheel_axis_above_rail":{"label":"ClickDrive wheel's axis above the rail's top","kind":"length","measurements":[{"id":"side-photo","value":0,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-142 351188c51fd3 (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.42-side-SW0100.jpg: SW0100 alone on a rail section, straight left side, 1200 x 1200)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 306.5 and 889.6 (the gaps' edges on rows 706 to 724), six pitches apart (std.picatinny.slot_pitch): 97.18 px a pitch, 246.65 px/in at the rail's middle; the teeth's tops on row 700 (the white ground shows through the slots down to their floors: the photo is level)","method":"the wheel's centre (row 700, its socket's middle) on the teeth's tops (700)","via":"harvest"},"note":"On the rail's top: the shaft half in the slot and half in the clamp's roof."}]},"wheel_outer_z":{"label":"ClickDrive wheel, its outer face left of the mount's middle","kind":"length","measurements":[{"id":"drawing","value":0.663,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-142 c08b4e430885 (Scalarworks' technical drawing of SW0100: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top): 340.4 px/in, as the other heights' drawings, the rail's top at row 1091 and its middle at column 600.25. From the clamp up to the body's shoulders the drawing is the 1.57 in's stroke for stroke; above them it is the 1.57 in's moved down 53 px","method":"the wheel's knurl drawn edge on under the left jaw's rounded corner, its outer edge at column 374.5, flush with the clamp's left face: 225.75 px from the rail's middle","via":"harvest"}}]},"wheel_thickness":{"label":"ClickDrive wheel, across","kind":"length","measurements":[{"id":"drawing","value":0.167,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-142 c08b4e430885 (Scalarworks' technical drawing of SW0100: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top): 340.4 px/in, as the other heights' drawings, the rail's top at row 1091 and its middle at column 600.25. From the clamp up to the body's shoulders the drawing is the 1.57 in's stroke for stroke; above them it is the 1.57 in's moved down 53 px","method":"the knurl drawn edge on, columns 374.5 to 431.5: 57 px","via":"harvest"}}]},"set_screw_z":{"label":"The set screw in the rear end (the ball detent's), left of the middle","kind":"length","measurements":[{"id":"drawing","value":0.579,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-142 c08b4e430885 (Scalarworks' technical drawing of SW0100: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top): 340.4 px/in, as the other heights' drawings, the rail's top at row 1091 and its middle at column 600.25. From the clamp up to the body's shoulders the drawing is the 1.57 in's stroke for stroke; above them it is the 1.57 in's moved down 53 px","method":"the concentric circles drawn low at the left (its centre at column 403, row 1093): 197.25 px left of the rail's middle","via":"harvest"}}],"note":"\"An integrated spring-loaded ball-detent exerts enough force against the crown to make it completely recoil proof.\" (the maker's page); the screw low in the rear end in the maker's side photo."},"set_screw_d":{"label":"The set screw's hole in the rear end","kind":"length","measurements":[{"id":"drawing","value":0.106,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-142 c08b4e430885 (Scalarworks' technical drawing of SW0100: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top): 340.4 px/in, as the other heights' drawings, the rail's top at row 1091 and its middle at column 600.25. From the clamp up to the body's shoulders the drawing is the 1.57 in's stroke for stroke; above them it is the 1.57 in's moved down 53 px","method":"the outermost of its circles, columns 385 to 421","via":"harvest"}}]},"jaw_inner_z":{"label":"The telescoping jaw: where it is split from the right wall, right of the middle","kind":"length","measurements":[{"id":"drawing","value":0.51,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-142 c08b4e430885 (Scalarworks' technical drawing of SW0100: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top): 340.4 px/in, as the other heights' drawings, the rail's top at row 1091 and its middle at column 600.25. From the clamp up to the body's shoulders the drawing is the 1.57 in's stroke for stroke; above them it is the 1.57 in's moved down 53 px","method":"the two strokes up the right wall at columns 770.5 and 777.5 (rows 1025 to 1105): their middle, 173.75 px right of the rail's middle","via":"harvest"}}]},"jaw_top":{"label":"The telescoping jaw, its top above the rail's top","kind":"length","measurements":[{"id":"drawing","value":0.195,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-142 c08b4e430885 (Scalarworks' technical drawing of SW0100: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top): 340.4 px/in, as the other heights' drawings, the rail's top at row 1091 and its middle at column 600.25. From the clamp up to the body's shoulders the drawing is the 1.57 in's stroke for stroke; above them it is the 1.57 in's moved down 53 px","method":"the stroke across the right wall (row 1024.5, columns 770 to 828) above the extension line (1091)","via":"harvest"}}]},"hook_top":{"label":"The telescoping jaw, where it turns in under the rail's head (its top there, below the rail's top)","kind":"length","measurements":[{"id":"drawing","value":-0.056,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-142 c08b4e430885 (Scalarworks' technical drawing of SW0100: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top): 340.4 px/in, as the other heights' drawings, the rail's top at row 1091 and its middle at column 600.25. From the clamp up to the body's shoulders the drawing is the 1.57 in's stroke for stroke; above them it is the 1.57 in's moved down 53 px","method":"the two strokes up the right wall curve in at row 1108 to meet the rail's upper face: 17 px under the extension line, as a height","via":"harvest"}}]},"guide_pin_x":{"label":"The guide pins' heads on the jaw's outer face, ahead of and behind the shaft's","kind":"length","measurements":[{"id":"leap-02","value":0.53,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{scalarworks-leap-02-micro-226.guide_pin_x}","via":"harvest"}}],"note":"No view of this mount's right side is on file: the LEAP/02's (Primary Arms' photo of it from the right front, 4945353b7bdf), on the same ClickDrive clamp, is the only one of the family's."},"guide_pin_d":{"label":"A guide pin's head","kind":"length","measurements":[{"id":"leap-02","value":0.1,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{scalarworks-leap-02-micro-226.guide_pin_d}","via":"harvest"},"note":"The LEAP/02's, as guide_pin_x."}]},"shaft_end_d":{"label":"The shaft's end on the jaw's outer face","kind":"length","measurements":[{"id":"leap-02","value":0.15,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{scalarworks-leap-02-micro-226.shaft_end_d}","via":"harvest"},"note":"The LEAP/02's, as guide_pin_x."}]},"head_ring":{"label":"The dark ring round each head in the jaw's face","kind":"length","measurements":[{"id":"leap-02","value":0.008,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{scalarworks-leap-02-micro-226.head_ring}","via":"harvest"},"note":"The LEAP/02's, as guide_pin_x."}]},"head_hole_depth":{"label":"How deep each head's hole is drawn","kind":"length","measurements":[{"id":"assumed","value":0.04,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the heads are flush with the face in the photo, and what is behind them doesn't show.","via":"harvest"}}]},"wheel_pocket_gap":{"label":"Clearance round the wheel in its pocket in the left wall","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the side photo shows the pocket's rim round the wheel's teeth as a dark ring a few pixels wide, which no scale on file resolves.","via":"harvest"}}]},"wheel_dish_depth":{"label":"How far the wheel's face is dished inside its rim","kind":"length","measurements":[{"id":"assumed","value":0.01,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the side photo shows the face's rim as a bright ring, its depth not.","via":"harvest"}}]},"wheel_socket_depth":{"label":"The socket in the wheel's middle, its depth","kind":"length","measurements":[{"id":"assumed","value":0.08,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the socket shows dark in the side photo, its depth not.","via":"harvest"}}]},"set_screw_hole_depth":{"label":"The set screw's hole in the rear end, its depth","kind":"length","measurements":[{"id":"assumed","value":0.1,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the drawing has the hole end on.","via":"harvest"}}]},"set_screw_recess":{"label":"How far the set screw's end stands back in its hole","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the photos show the screw's end just inside the hole's rim.","via":"harvest"}}]},"edge_break":{"label":"The aluminium's edges, broken","kind":"length","measurements":[{"id":"assumed","value":0.008,"unit":"in","pm":0.005,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the photos show every edge of the body softened, by an amount no view on file resolves.","via":"harvest"}}]},"weight":{"label":"Weight (the mount alone)","kind":"mass","measurements":[{"id":"page","value":43,"unit":"g","stated":"Weight SW0100 : 43g (1.52oz) SW0110 : 45g (1.58oz) SW0120 : 51g (1.80oz)","source":{"type":"spec","publisher":"manufacturer","name":"Scalarworks, LEAP/01 (product page, SPECIFICATIONS)","url":"https://scalarworks.com/shop/quick-detach-mounts/leap-01/","retrieved":"2026-11-03","via":"harvest"}},{"id":"trex","value":1.52,"unit":"oz","stated":"1.42\" Mount 1.52 oz.","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, Scalarworks LEAP/01 Aimpoint Micro T-2 QD Mount","url":"https://www.trex-arms.com/store/scalarworks-leap-01-aimpoint-micro-t-2-qd-mount-73479","retrieved":"2026-11-03","via":"harvest"}},{"id":"wing","value":1.52,"unit":"oz","stated":"Absolute Co-Witness : 1.52 oz.","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Scalarworks LEAP Aimpoint Micro Mount","url":"https://www.wingtactical.com/accessories/optics-sights/optic-sight-mounts/scalarworks-leap-aimpoint-micro-mount/","retrieved":"2026-11-03","via":"harvest"}}],"adopt":{"from":"page","reason":"The maker's figure for this height; two sellers quote it in ounces."}}}},{"subject":"scalarworks-leap-01-micro-157","title":"Scalarworks LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.57 in (SW0110)","dimensions":{"optical_axis_above_rail":{"label":"Optical axis above the rail's top, with an Aimpoint Micro T-2 on it (the maker's height)","kind":"length","measurements":[{"id":"page","value":1.57,"unit":"in","stated":"Optic center height over rail SW0100 : 1.42\" SW0110 : 1.57\" SW0120 : 1.93\"","source":{"type":"spec","publisher":"manufacturer","name":"Scalarworks, LEAP/01 (product page, SPECIFICATIONS)","url":"https://scalarworks.com/shop/quick-detach-mounts/leap-01/","retrieved":"2026-11-03","via":"harvest"},"note":"The same page, at the choice of height: \"HEIGHT: 1.42\" 1.57\" 1.93\"\"; MidwayUSA's page: \"Note: Height measurement is from the top of the rail to the center of the optic.\""},{"id":"drawing","value":1.57,"unit":"in","stated":"1.57” OPTIC CENTER","source":{"type":"spec","publisher":"manufacturer","name":"Scalarworks, the technical drawing of SW0110 in the LEAP/01 page's gallery for the 1.57 in height (references/scalarworks-leap-01-micro-157 6359f81fa1be)","url":"https://scalarworks.com/wp-content/uploads/scalarworks-SW0110-diagram-A.png","retrieved":"2026-11-03","via":"harvest"},"note":"From the extension line through the clamp's shaft (the rail's top) to the T-2's axis."},{"id":"wing","value":1.57,"unit":"in","stated":"Center Height Over Rail: Absolute Co-Witness : 1.42\" (36mm) Lower 1/3 : 1.57\" (40mm)","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Scalarworks LEAP Aimpoint Micro Mount","url":"https://www.wingtactical.com/accessories/optics-sights/optic-sight-mounts/scalarworks-leap-aimpoint-micro-mount/","retrieved":"2026-11-03","via":"harvest"}},{"id":"as-drawn","value":1.569,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-157 6359f81fa1be (Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 1.57 in's own lines 534 px apart (340.1) and the 21.5 mm's 289.5 px (342.0): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25","method":"the red dot's centroid (row 557.0) above the extension line (row 1091): 534 px","via":"harvest"}}],"adopt":{"from":"page","reason":"The maker's stated centre height, the figure a buyer compares and the category's (D101); its drawing's own lines put the axis there to 0.001 in."},"note":"The maker names no dot in the sentence (\"Optic center height over rail\"); the page is \"LEAP/01 Premium Aimpoint Micro T-2 mounts.\", its drawing of this height draws a T-2 on the mount, and its weight chart weighs it \"with all hardware necessary to attach an Aimpoint Micro T-2 in lower-third co-witness height\": the height is the T-2's. Its co-witness, in the same table: \"SW0110 : Lower-Third\"."},"window_top_above_rail":{"label":"Top of the window through the mount (end to end), above the rail's top","kind":"length","measurements":[{"id":"drawing","value":21.5,"unit":"mm","stated":"21.5MM","source":{"type":"spec","publisher":"manufacturer","name":"Scalarworks, the technical drawing of SW0110 in the LEAP/01 page's gallery for the 1.57 in height (references/scalarworks-leap-01-micro-157 6359f81fa1be)","url":"https://scalarworks.com/wp-content/uploads/scalarworks-SW0110-diagram-A.png","retrieved":"2026-11-03","via":"harvest"},"note":"From the same extension line as the 1.57 in to the top of the window's throat (the inner of the two outlines drawn round it)."},{"id":"as-drawn","value":0.8505,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-157 6359f81fa1be (Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 1.57 in's own lines 534 px apart (340.1) and the 21.5 mm's 289.5 px (342.0): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25","method":"the throat's top stroke (row 801.5) above the extension line (1091): 289.5 px","via":"harvest"},"note":"21.60 mm: the check of the drawing's scale."}],"adopt":{"from":"drawing","reason":"The maker's stated dimension; its lines read the same at the scale the rail and the axis give."}},"deck_above_rail":{"label":"The deck's floor (where the dot's base sits) above the rail's top","kind":"length","measurements":[{"id":"less-t2","value":0.981,"unit":"in","pm":0.037,"source":{"type":"derived","expr":"{.optical_axis_above_rail} - {aimpoint-micro-t-2.axis_above_base}","via":"harvest"},"note":"1.57 in less the T-2's 0.589 in."},{"id":"drawing","value":0.965,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-157 6359f81fa1be (Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 1.57 in's own lines 534 px apart (340.1) and the 21.5 mm's 289.5 px (342.0): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25","method":"the stroke the T-2's foot stands on between the rims (row 762.5, from column 510 to 690) above the extension line (1091): 328.5 px. The T-2's axis is 205.5 px over it in the same drawing: 0.604 in, inside the 0.589 ± 0.037 the T-2's ledger has","via":"harvest"}}],"adopt":{"from":"less-t2","reason":"The category's figure (D101): the maker's axis height for the T-2 less the T-2's own axis over its base, which puts the T-2 at the maker's 1.57 in. The maker's drawing has the floor 0.016 in lower, inside the two readings' ±."},"note":"The deck is a floor between two rims that run its whole length (Wing Tactical's photo from above, b9f81ccd5367): the T-2's foot sits down between them on the floor and its housing's underside on the rims' tops (the drawing). The floor is where a dot's base is put (D101): the T-2's own axis over its base (aimpoint-micro-t-2.axis_above_base) is read to the plane its foot is screwed to. The maker states only the axis's height, for the T-2: the floor is that less the T-2's axis over its base. The drawing puts it there within the two readings' ±."},"rim_top_above_rail":{"label":"The deck's two rims, their tops above the rail's top","kind":"length","measurements":[{"id":"drawing","value":1.046,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-157 6359f81fa1be (Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 1.57 in's own lines 534 px apart (340.1) and the 21.5 mm's 289.5 px (342.0): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25","method":"the rims' top stroke (row 735, from column 440 to 500 and 702 to 760) above the extension line (1091): 356 px","via":"harvest"}},{"id":"side-photo","value":1.06,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-157 e656d3c79e0b (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.57-side-SW0110.jpg: SW0110 alone on a rail section, straight left side, 1200 x 1200)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 307.0 and 890.0 (the gaps' edges on rows 706 to 724), six pitches apart (std.picatinny.slot_pitch): 97.17 px a pitch, 246.6 px/in at the rail's middle; the teeth's tops on row 700.5 (through the slots the white ground shows down to their floors, 29.5 px lower: the photo is level)","method":"the mount's top edge (row 439, from column 320 to 738) above the teeth's tops: 261.5 px","via":"harvest"},"note":"1.3% over the drawing: the mount's near face stands nearer the lens than the rail's middle the slots are read at (its length reads as much over Wing Tactical's, length)."}],"adopt":{"from":"drawing","reason":"The maker's drawing, at a scale three of its own figures agree on; the photo reads the near face 1.3% large."},"note":"What the side views show as the mount's top. Not drawn above the deck's floor: every Micro dot on file is drawn with its base as wide as its housing, and the rims would stand inside it (the part's approximations)."},"deck_x":{"label":"The footprint's middle along the deck, ahead of the wheel's shaft","kind":"length","measurements":[{"id":"side-photo","value":0.28,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-157 e656d3c79e0b (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.57-side-SW0110.jpg: SW0110 alone on a rail section, straight left side, 1200 x 1200)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 307.0 and 890.0 (the gaps' edges on rows 706 to 724), six pitches apart (std.picatinny.slot_pitch): 97.17 px a pitch, 246.6 px/in at the rail's middle; the teeth's tops on row 700.5 (through the slots the white ground shows down to their floors, 29.5 px lower: the photo is level)","method":"the middle of the rims' flat top, between the step at its front end (column 320) and where its rear end scoops down (738): column 529, 69.5 px ahead of the wheel's shaft (column 598.5, the slot midway). The lug that goes up into a dot's base is in the middle of the deck in Wing Tactical's photo from above (b9f81ccd5367)","via":"harvest"}},{"id":"bundle","value":0.26,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-157 d1db0793b411 (Scalarworks, scalarworks-leap-01-aimpoint-micro-t2-bundle-1.57-side-SW0110-T2.jpg: the mount with a Micro T-2 on it, straight left side)","scaleRef":"the rail section's slots at columns 330.5 and 866.0, six pitches apart: 89.25 px a pitch, 226.5 px/in; the wheel's centre at 597.5","method":"the T-2's rubber covers, lids closed, from column 187 to 877 at its axis: their middle 0.289 in ahead of the wheel; the T-2's model has its footprint's middle 0.03 in behind its covers' middle (aimpoint-micro-t-2.glb, the covers from -1.403 to 1.461 in)","via":"harvest"},"note":"The check: where the T-2 screwed to the footprint has its own footprint's middle."}],"adopt":{"from":"side-photo","reason":"The mount's own deck; the T-2 on it in the same set-up puts its footprint's middle 0.02 in further back, within both ±."}},"mount_length":{"label":"The clamp's length along the rail, at its foot","kind":"length","measurements":[{"id":"side-photo","value":1.557,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-157 e656d3c79e0b (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.57-side-SW0110.jpg: SW0110 alone on a rail section, straight left side, 1200 x 1200)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 307.0 and 890.0 (the gaps' edges on rows 706 to 724), six pitches apart (std.picatinny.slot_pitch): 97.17 px a pitch, 246.6 px/in at the rail's middle; the teeth's tops on row 700.5 (through the slots the white ground shows down to their floors, 29.5 px lower: the photo is level)","method":"the clamp's foot under the rail's top (row 757), from the front leg's lower end (column 431.1, where the traced outline's foot ends) to the rear face (815): 383.9 px","via":"harvest"},"note":"As read: the near face reads 1.3% large (rim_top_above_rail)."}]},"clamp_front":{"label":"The clamp's foot, its front end ahead of the wheel's shaft","kind":"length","measurements":[{"id":"side-photo","value":0.679,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-157 e656d3c79e0b (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.57-side-SW0110.jpg: SW0110 alone on a rail section, straight left side, 1200 x 1200)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 307.0 and 890.0 (the gaps' edges on rows 706 to 724), six pitches apart (std.picatinny.slot_pitch): 97.17 px a pitch, 246.6 px/in at the rail's middle; the teeth's tops on row 700.5 (through the slots the white ground shows down to their floors, 29.5 px lower: the photo is level)","method":"the traced outline's foot (profiles.side) ends at column 431.1, 167.4 px ahead of the shaft (598.5)","via":"harvest"}}]},"clamp_rear":{"label":"The clamp's foot, its rear end behind the wheel's shaft","kind":"length","measurements":[{"id":"side-photo","value":0.878,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-157 e656d3c79e0b (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.57-side-SW0110.jpg: SW0110 alone on a rail section, straight left side, 1200 x 1200)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 307.0 and 890.0 (the gaps' edges on rows 706 to 724), six pitches apart (std.picatinny.slot_pitch): 97.17 px a pitch, 246.6 px/in at the rail's middle; the teeth's tops on row 700.5 (through the slots the white ground shows down to their floors, 29.5 px lower: the photo is level)","method":"the rear face, column 815, 216.5 px behind the shaft","via":"harvest"}}]},"length":{"label":"Overall length along the rail","kind":"length","measurements":[{"id":"wing","value":2.06,"unit":"in","stated":"Length: 2.06\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Scalarworks LEAP Aimpoint Micro Mount","url":"https://www.wingtactical.com/accessories/optics-sights/optic-sight-mounts/scalarworks-leap-aimpoint-micro-mount/","retrieved":"2026-11-03","via":"harvest"},"note":"One figure on a page that sells the 1.42 and the 1.57 in; what it spans isn't said."},{"id":"side-photo","value":2.088,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-157 e656d3c79e0b (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.57-side-SW0110.jpg: SW0110 alone on a rail section, straight left side, 1200 x 1200)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 307.0 and 890.0 (the gaps' edges on rows 706 to 724), six pitches apart (std.picatinny.slot_pitch): 97.17 px a pitch, 246.6 px/in at the rail's middle; the teeth's tops on row 700.5 (through the slots the white ground shows down to their floors, 29.5 px lower: the photo is level)","method":"the deck's front step (column 300) to the rear face (815): 515 px","via":"harvest"},"note":"1.4% over Wing Tactical's: the near face reads 1.3% large (rim_top_above_rail)."}],"adopt":{"from":"wing","reason":"A seller's figure, which the photo reads within the 1.3% its near face reads large by."}},"width":{"label":"Overall width across the clamp","kind":"length","measurements":[{"id":"drawing","value":1.334,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-157 6359f81fa1be (Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 1.57 in's own lines 534 px apart (340.1) and the 21.5 mm's 289.5 px (342.0): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25","method":"the clamp's two outer faces, the strokes at columns 373.5 and 827.5 (rows 1000 to 1120): 454 px, about column 600.5, the rail's middle","via":"harvest"}},{"id":"wing","value":1.338,"unit":"in","stated":"Width: 1.338\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Scalarworks LEAP Aimpoint Micro Mount","url":"https://www.wingtactical.com/accessories/optics-sights/optic-sight-mounts/scalarworks-leap-aimpoint-micro-mount/","retrieved":"2026-11-03","via":"harvest"},"note":"One figure for a page that sells two heights."}],"adopt":{"from":"drawing","reason":"The maker's drawing of this height; a seller's figure agrees to 0.004 in."},"note":"The maker: \"the Leap mount is symmetrical, protruding less than 7mm from either side of your Picatinny rail.\" (0.835 in and twice 7 mm: under 1.386 in)."},"body_width":{"label":"The body under the deck, across (its two side walls' outer faces)","kind":"length","measurements":[{"id":"drawing","value":0.94,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-157 6359f81fa1be (Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 1.57 in's own lines 534 px apart (340.1) and the 21.5 mm's 289.5 px (342.0): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25","method":"the walls' strokes at columns 440.5 and 760.5 (rows 750 to 920): 320 px","via":"harvest"}}]},"clamp_below_rail":{"label":"The clamp's foot below the rail's top","kind":"length","measurements":[{"id":"drawing","value":0.234,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-157 6359f81fa1be (Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 1.57 in's own lines 534 px apart (340.1) and the 21.5 mm's 289.5 px (342.0): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25","method":"the jaws' feet (row 1170.5, columns 430 to 476 and 723 to 780) under the extension line (1091): 79.5 px","via":"harvest"}},{"id":"side-photo","value":0.229,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-157 e656d3c79e0b (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.57-side-SW0110.jpg: SW0110 alone on a rail section, straight left side, 1200 x 1200)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 307.0 and 890.0 (the gaps' edges on rows 706 to 724), six pitches apart (std.picatinny.slot_pitch): 97.17 px a pitch, 246.6 px/in at the rail's middle; the teeth's tops on row 700.5 (through the slots the white ground shows down to their floors, 29.5 px lower: the photo is level)","method":"the left jaw's foot (row 757) under the teeth's tops (700.5): 56.5 px","via":"harvest"}}],"adopt":{"from":"drawing","reason":"The finer reading; the photo agrees."}},"wheel_d":{"label":"ClickDrive wheel, over its teeth","kind":"length","measurements":[{"id":"side-photo","value":0.629,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-157 e656d3c79e0b (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.57-side-SW0110.jpg: SW0110 alone on a rail section, straight left side, 1200 x 1200)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 307.0 and 890.0 (the gaps' edges on rows 706 to 724), six pitches apart (std.picatinny.slot_pitch): 97.17 px a pitch, 246.6 px/in at the rail's middle; the teeth's tops on row 700.5 (through the slots the white ground shows down to their floors, 29.5 px lower: the photo is level)","method":"the teeth's tips 76.25 px above and 78.75 px below the wheel's centre (column 598.75, row 700): 155 px","via":"harvest"},"note":"The wheel's face is the nearest thing to the lens: as read, perhaps 1.3% large."}],"note":"Twenty teeth: counted on the side photo's upper half, where the rim is clear of the body (tips about 18 degrees apart: at 9, 29, 45 and 63 degrees from the top)."},"wheel_root_d":{"label":"ClickDrive wheel, at the foot of its teeth","kind":"length","measurements":[{"id":"side-photo","value":0.527,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-157 e656d3c79e0b (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.57-side-SW0110.jpg: SW0110 alone on a rail section, straight left side, 1200 x 1200)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 307.0 and 890.0 (the gaps' edges on rows 706 to 724), six pitches apart (std.picatinny.slot_pitch): 97.17 px a pitch, 246.6 px/in at the rail's middle; the teeth's tops on row 700.5 (through the slots the white ground shows down to their floors, 29.5 px lower: the photo is level)","method":"the valleys between the top teeth, 65 px from the centre","via":"harvest"}}]},"wheel_face_d":{"label":"ClickDrive wheel, the face inside its rim","kind":"length","measurements":[{"id":"side-photo","value":0.572,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-157 e656d3c79e0b (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.57-side-SW0110.jpg: SW0110 alone on a rail section, straight left side, 1200 x 1200)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 307.0 and 890.0 (the gaps' edges on rows 706 to 724), six pitches apart (std.picatinny.slot_pitch): 97.17 px a pitch, 246.6 px/in at the rail's middle; the teeth's tops on row 700.5 (through the slots the white ground shows down to their floors, 29.5 px lower: the photo is level)","method":"the bright ring round the face (\"SCALARWORKS\" inside it), 70.6 px from the centre across","via":"harvest"}}]},"wheel_hub_d":{"label":"ClickDrive wheel, the socket in its middle","kind":"length","measurements":[{"id":"side-photo","value":0.13,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-157 e656d3c79e0b (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.57-side-SW0110.jpg: SW0110 alone on a rail section, straight left side, 1200 x 1200)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 307.0 and 890.0 (the gaps' edges on rows 706 to 724), six pitches apart (std.picatinny.slot_pitch): 97.17 px a pitch, 246.6 px/in at the rail's middle; the teeth's tops on row 700.5 (through the slots the white ground shows down to their floors, 29.5 px lower: the photo is level)","method":"the dark hole at the wheel's middle, columns 582 to 614","via":"harvest"}}]},"wheel_axis_above_rail":{"label":"ClickDrive wheel's axis above the rail's top","kind":"length","measurements":[{"id":"side-photo","value":0.002,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-157 e656d3c79e0b (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.57-side-SW0110.jpg: SW0110 alone on a rail section, straight left side, 1200 x 1200)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 307.0 and 890.0 (the gaps' edges on rows 706 to 724), six pitches apart (std.picatinny.slot_pitch): 97.17 px a pitch, 246.6 px/in at the rail's middle; the teeth's tops on row 700.5 (through the slots the white ground shows down to their floors, 29.5 px lower: the photo is level)","method":"the wheel's centre (row 700, midway between its top and bottom teeth's tips and the middle of its socket) above the teeth's tops (700.5)","via":"harvest"},"note":"On the rail's top: the shaft is half in the slot and half in the clamp's roof."}]},"wheel_outer_z":{"label":"ClickDrive wheel, its outer face left of the mount's middle","kind":"length","measurements":[{"id":"drawing","value":0.663,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-157 6359f81fa1be (Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 1.57 in's own lines 534 px apart (340.1) and the 21.5 mm's 289.5 px (342.0): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25","method":"the wheel's knurl drawn edge on under the left jaw's rounded corner (rows 1140 to 1200), its outer edge at column 374.5, flush with the clamp's left face: 225.75 px from the rail's middle","via":"harvest"}}]},"wheel_thickness":{"label":"ClickDrive wheel, across","kind":"length","measurements":[{"id":"drawing","value":0.167,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-157 6359f81fa1be (Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 1.57 in's own lines 534 px apart (340.1) and the 21.5 mm's 289.5 px (342.0): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25","method":"the knurl drawn edge on, columns 374.5 to 431.5: 57 px","via":"harvest"}}]},"set_screw_z":{"label":"The set screw in the rear end (the ball detent's), left of the middle","kind":"length","measurements":[{"id":"drawing","value":0.579,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-157 6359f81fa1be (Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 1.57 in's own lines 534 px apart (340.1) and the 21.5 mm's 289.5 px (342.0): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25","method":"the concentric circles drawn low at the left (its centre at column 403, row 1093): 197.25 px left of the rail's middle","via":"harvest"}}],"note":"\"An integrated spring-loaded ball-detent exerts enough force against the crown to make it completely recoil proof.\" (the maker's page): a screw in the rear end, in line with the wheel's middle across, at the height of its axis, its red nylon patch in Wing Tactical's photos."},"set_screw_d":{"label":"The set screw's hole in the rear end","kind":"length","measurements":[{"id":"drawing","value":0.106,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-157 6359f81fa1be (Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 1.57 in's own lines 534 px apart (340.1) and the 21.5 mm's 289.5 px (342.0): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25","method":"the outermost of its circles, columns 385 to 421","via":"harvest"}}]},"weight":{"label":"Weight (the mount alone)","kind":"mass","measurements":[{"id":"page","value":45,"unit":"g","stated":"Weight SW0100 : 43g (1.52oz) SW0110 : 45g (1.58oz) SW0120 : 51g (1.80oz)","source":{"type":"spec","publisher":"manufacturer","name":"Scalarworks, LEAP/01 (product page, SPECIFICATIONS)","url":"https://scalarworks.com/shop/quick-detach-mounts/leap-01/","retrieved":"2026-11-03","via":"harvest"}},{"id":"chart","value":47,"unit":"g","stated":"Scalarworks ® SW0110 (47grams)","source":{"type":"spec","publisher":"manufacturer","name":"Scalarworks, LEAP/01 (product page, SPECIFICATIONS)","url":"https://scalarworks.com/shop/quick-detach-mounts/leap-01/","retrieved":"2026-11-03","via":"harvest"},"note":"The page's weight chart: \"All mounts weighed under the same conditions with all hardware necessary to attach an Aimpoint Micro T-2 in lower-third co-witness height.\": the mount and its four screws, which are the T-2's to carry here."},{"id":"trex","value":1.58,"unit":"oz","stated":"1.57\" Mount 1.58 oz.","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, Scalarworks LEAP/01 Aimpoint Micro T-2 QD Mount","url":"https://www.trex-arms.com/store/scalarworks-leap-01-aimpoint-micro-t-2-qd-mount-73479","retrieved":"2026-11-03","via":"harvest"}},{"id":"wing","value":1.58,"unit":"oz","stated":"Lower 1/3 : 1.58 oz","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Scalarworks LEAP Aimpoint Micro Mount","url":"https://www.wingtactical.com/accessories/optics-sights/optic-sight-mounts/scalarworks-leap-aimpoint-micro-mount/","retrieved":"2026-11-03","via":"harvest"}},{"id":"midway","value":1.65,"unit":"oz","stated":"Weight 1.65 Ounce","source":{"type":"spec","publisher":"retailer","name":"MidwayUSA, Scalarworks LEAP Aimpoint Micro QD Picatinny Red Dot Mount (product 1022884560)","url":"https://www.midwayusa.com/product/1022884560","retrieved":"2026-11-03","via":"harvest"},"note":"One figure for a page that sells the 1.57 and the 1.93 in."}],"adopt":{"from":"page","reason":"The maker's figure for this height; two sellers quote it in ounces. The chart's 47 g is with the four screws; MidwayUSA's is one figure for two heights."}},"jaw_inner_z":{"label":"The telescoping jaw: where it is split from the right wall, right of the middle","kind":"length","measurements":[{"id":"drawing","value":0.51,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-157 6359f81fa1be (Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 1.57 in's own lines 534 px apart (340.1) and the 21.5 mm's 289.5 px (342.0): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25","method":"the two strokes up the right wall at columns 770.5 and 777.5 (rows 1025 to 1105): their middle, 173.75 px right of the rail's middle","via":"harvest"}}],"note":"\"ClickDrive's low-profile thumbscrew and low-friction telescoping clamp ...\" (the maker's page): the drawing splits the right wall's lower part off as the jaw that moves, by two strokes 7 px apart up the wall and one across it."},"jaw_top":{"label":"The telescoping jaw, its top above the rail's top","kind":"length","measurements":[{"id":"drawing","value":0.195,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-157 6359f81fa1be (Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 1.57 in's own lines 534 px apart (340.1) and the 21.5 mm's 289.5 px (342.0): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25","method":"the stroke across the right wall (row 1024.5, columns 770 to 828) above the extension line (1091)","via":"harvest"}}]},"hook_top":{"label":"The telescoping jaw, where it turns in under the rail's head (its top there, below the rail's top)","kind":"length","measurements":[{"id":"drawing","value":-0.056,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-157 6359f81fa1be (Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 1.57 in's own lines 534 px apart (340.1) and the 21.5 mm's 289.5 px (342.0): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25","method":"the two strokes up the right wall curve in at row 1108 to meet the rail's upper face: 17 px under the extension line, as a height","via":"harvest"}}]},"guide_pin_x":{"label":"The guide pins' heads on the jaw's outer face, ahead of and behind the shaft's","kind":"length","measurements":[{"id":"leap-02","value":0.53,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{scalarworks-leap-02-micro-226.guide_pin_x}","via":"harvest"}}],"note":"No view of this mount's right side is on file: the LEAP/02's (Primary Arms' photo of it from the right front, 4945353b7bdf), on the same ClickDrive clamp, is the only one of the family's."},"guide_pin_d":{"label":"A guide pin's head","kind":"length","measurements":[{"id":"leap-02","value":0.1,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{scalarworks-leap-02-micro-226.guide_pin_d}","via":"harvest"},"note":"The LEAP/02's, as guide_pin_x."}]},"shaft_end_d":{"label":"The shaft's end on the jaw's outer face","kind":"length","measurements":[{"id":"leap-02","value":0.15,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{scalarworks-leap-02-micro-226.shaft_end_d}","via":"harvest"},"note":"The LEAP/02's, as guide_pin_x."}]},"head_ring":{"label":"The dark ring round each head in the jaw's face","kind":"length","measurements":[{"id":"leap-02","value":0.008,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{scalarworks-leap-02-micro-226.head_ring}","via":"harvest"},"note":"The LEAP/02's, as guide_pin_x."}]},"head_hole_depth":{"label":"How deep each head's hole is drawn","kind":"length","measurements":[{"id":"assumed","value":0.04,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the heads are flush with the face in the photo, and what is behind them doesn't show.","via":"harvest"}}]},"wheel_pocket_gap":{"label":"Clearance round the wheel in its pocket in the left wall","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the side photo shows the pocket's rim round the wheel's teeth as a dark ring a few pixels wide, which no scale on file resolves.","via":"harvest"}}]},"wheel_dish_depth":{"label":"How far the wheel's face is dished inside its rim","kind":"length","measurements":[{"id":"assumed","value":0.01,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the side photo shows the face's rim as a bright ring, its depth not; no view on file has the wheel in profile.","via":"harvest"}}]},"wheel_socket_depth":{"label":"The socket in the wheel's middle, its depth","kind":"length","measurements":[{"id":"assumed","value":0.08,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the socket shows dark in the side photo, its depth not.","via":"harvest"}}]},"set_screw_hole_depth":{"label":"The set screw's hole in the rear end, its depth","kind":"length","measurements":[{"id":"assumed","value":0.1,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the drawing has the hole end on, and the screw runs on toward the wheel's crown inside.","via":"harvest"}}]},"set_screw_recess":{"label":"How far the set screw's end stands back in its hole","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: Wing Tactical's photos show the screw's red nylon patch just inside the hole's rim.","via":"harvest"}}]},"edge_break":{"label":"The aluminium's edges, broken","kind":"length","measurements":[{"id":"assumed","value":0.008,"unit":"in","pm":0.005,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the photos show every edge of the body softened, by an amount no view on file resolves.","via":"harvest"}}]}}},{"subject":"scalarworks-leap-01-micro-193","title":"Scalarworks LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.93 in (SW0120)","dimensions":{"optical_axis_above_rail":{"label":"Optical axis above the rail's top, with an Aimpoint Micro T-2 on it (the maker's height)","kind":"length","measurements":[{"id":"page","value":1.93,"unit":"in","stated":"Optic center height over rail SW0100 : 1.42\" SW0110 : 1.57\" SW0120 : 1.93\"","source":{"type":"spec","publisher":"manufacturer","name":"Scalarworks, LEAP/01 (product page, SPECIFICATIONS)","url":"https://scalarworks.com/shop/quick-detach-mounts/leap-01/","retrieved":"2026-11-03","via":"harvest"},"note":"MidwayUSA's page: \"Note: Height measurement is from the top of the rail to the center of the optic.\""},{"id":"drawing","value":1.93,"unit":"in","stated":"1.93” OPTIC CENTER","source":{"type":"spec","publisher":"manufacturer","name":"Scalarworks, the technical drawing of SW0120 in the LEAP/01 page's gallery for the 1.93 in height (references/scalarworks-leap-01-micro-193 c5d15b40764b)","url":"https://scalarworks.com/wp-content/uploads/scalarworks-SW0120-diagram-A.png","retrieved":"2026-11-03","via":"harvest"},"note":"From the extension line through the clamp's shaft (the rail's top) to the T-2's axis."},{"id":"as-drawn","value":1.921,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-193 c5d15b40764b (Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 29.8 mm's own lines 400.5 px apart (341.4): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. The drawing is the 1.57 in's stroke for stroke from the clamp up to the body's shoulders","method":"the red dot's centroid (row 437.0) above the extension line (row 1091): 654 px","via":"harvest"},"note":"0.009 in under the stated figure: the 1.93 in's own lines (654 px) are at 338.9 px/in, half a percent off the scale the rail and the 29.8 mm agree on."}],"adopt":{"from":"page","reason":"The maker's stated centre height, the figure a buyer compares and the category's (D101); its drawing's lines put the axis 0.009 in lower at the scale its rail gives, inside the two readings' ±."},"note":"The maker names no dot in the sentence (\"Optic center height over rail\"); the page is \"LEAP/01 Premium Aimpoint Micro T-2 mounts.\" and its drawing of this height draws a T-2 on the mount: the height is the T-2's. Its co-witness, in the same table: \"SW0120 : Only with 1.93\" PEAK/02\" (the maker's own taller backup sights). The page's advice: \"Choose 1.93″ height if: You value a more relaxed heads-up shooting style. You are willing to upgrade to 1.93″ PEAK/02 BUIS. You shoot with a top-rail mounted light or laser.\""},"window_top_above_rail":{"label":"Top of the window through the mount (end to end), above the rail's top","kind":"length","measurements":[{"id":"drawing","value":29.8,"unit":"mm","stated":"29.8MM","source":{"type":"spec","publisher":"manufacturer","name":"Scalarworks, the technical drawing of SW0120 in the LEAP/01 page's gallery for the 1.93 in height (references/scalarworks-leap-01-micro-193 c5d15b40764b)","url":"https://scalarworks.com/wp-content/uploads/scalarworks-SW0120-diagram-A.png","retrieved":"2026-11-03","via":"harvest"},"note":"From the same extension line as the 1.93 in to the top of the window's throat (the inner of the two outlines drawn round it)."},{"id":"as-drawn","value":1.1766,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-193 c5d15b40764b (Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 29.8 mm's own lines 400.5 px apart (341.4): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. The drawing is the 1.57 in's stroke for stroke from the clamp up to the body's shoulders","method":"the throat's top stroke (row 690.5) above the extension line (1091): 400.5 px","via":"harvest"},"note":"29.89 mm: the check of the drawing's scale."}],"adopt":{"from":"drawing","reason":"The maker's stated dimension; its lines read the same at the scale the rail gives."},"note":"The drawings' window figures don't step as the heights do (17.5, 21.5 and 29.8 mm for 1.42, 1.57 and 1.93 in): in this height the deck over the window is 0.029 in (0.75 mm) thicker than in the 1.57 in's drawing (the floor 49 px over the window's throat here, 39 px there), while the floors step by 0.356 in for the stated 0.36 and the T-2 stands 0.601 in over its floor here and 0.604 in there. The deck's floor is read on the drawing, not worked out from the window."},"deck_above_rail":{"label":"The deck's floor (where the dot's base sits) above the rail's top","kind":"length","measurements":[{"id":"less-t2","value":1.341,"unit":"in","pm":0.037,"source":{"type":"derived","expr":"{.optical_axis_above_rail} - {aimpoint-micro-t-2.axis_above_base}","via":"harvest"},"note":"1.93 in less the T-2's 0.589 in."},{"id":"drawing","value":1.3205,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-193 c5d15b40764b (Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 29.8 mm's own lines 400.5 px apart (341.4): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. The drawing is the 1.57 in's stroke for stroke from the clamp up to the body's shoulders","method":"the stroke the T-2's foot stands on between the rims (row 641.5) above the extension line (1091): 449.5 px. The T-2's axis is 204.5 px over it: 0.601 in, inside the 0.589 ± 0.037 the T-2's ledger has","via":"harvest"}}],"adopt":{"from":"less-t2","reason":"The category's figure (D101): the maker's axis height for the T-2 less the T-2's own axis over its base, which puts the T-2 at the maker's 1.93 in. The maker's drawing has the floor 0.02 in lower, inside the two readings' ±."},"note":"A floor between two rims that run the deck's whole length, the T-2's foot down on it between them and its housing on the rims' tops (the drawing; the deck from above in Wing Tactical's photo of a LEAP/01, filed with the 1.57 in). The maker states only the axis's height, for the T-2: the floor is that less the T-2's axis over its base (D101). The drawing puts it there within the two readings' ±."},"rim_top_above_rail":{"label":"The deck's two rims, their tops above the rail's top","kind":"length","measurements":[{"id":"drawing","value":1.398,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-193 c5d15b40764b (Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 29.8 mm's own lines 400.5 px apart (341.4): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. The drawing is the 1.57 in's stroke for stroke from the clamp up to the body's shoulders","method":"the rims' top stroke (row 615) above the extension line (1091): 476 px","via":"harvest"}},{"id":"side-photo","value":1.416,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-193 c3827ed5c44c (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.93-side-SW0120.jpg: SW0120 alone on a rail section, straight left side, 1200 x 1200)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 306.5 and 890.0 (the gaps' edges on rows 700 to 724), six pitches apart (std.picatinny.slot_pitch): 97.25 px a pitch, 246.8 px/in at the rail's middle; the teeth's tops on row 697.5 (the white ground shows through the slots down to their floors: the photo is level)","method":"the mount's top edge (row 348, from column 300 to 717) above the teeth's tops: 349.5 px","via":"harvest"},"note":"1.3% over the drawing, as the 1.57 in's photo is: the near face stands nearer the lens than the rail's middle."}],"adopt":{"from":"drawing","reason":"The maker's drawing at the scale its rail gives; the photo reads the near face 1.3% large."},"note":"What the side views show as the mount's top. Not drawn above the deck's floor: every Micro dot on file is drawn with its base as wide as its housing (the part's approximations)."},"deck_x":{"label":"The footprint's middle along the deck, ahead of the wheel's shaft","kind":"length","measurements":[{"id":"side-photo","value":0.364,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-193 c3827ed5c44c (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.93-side-SW0120.jpg: SW0120 alone on a rail section, straight left side, 1200 x 1200)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 306.5 and 890.0 (the gaps' edges on rows 700 to 724), six pitches apart (std.picatinny.slot_pitch): 97.25 px a pitch, 246.8 px/in at the rail's middle; the teeth's tops on row 697.5 (the white ground shows through the slots down to their floors: the photo is level)","method":"the middle of the rims' flat top, between the step at its front end (column 300) and where its rear end scoops down (717): column 508.5, 89.75 px ahead of the wheel's shaft (column 598.25, the slot midway)","via":"harvest"}},{"id":"bundle","value":0.41,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-193 990c8c035f13 (Scalarworks, scalarworks-leap-01-aimpoint-micro-t2-bundle-1.93-side-SW0120-T2.jpg: the mount with a Micro T-2 on it, straight left side)","scaleRef":"the rail section's slots at columns 333.0 and 868.5, six pitches apart: 89.25 px a pitch, 226.5 px/in; the shaft in the slot midway, column 600.75","method":"the T-2's rubber covers, lids closed, from column 162 to 840 at its axis: their middle 0.44 in ahead of the shaft; the T-2's model has its footprint's middle 0.03 in behind its covers' middle","via":"harvest"},"note":"The check: where the T-2 screwed to the footprint has its own footprint's middle."}],"adopt":{"from":"side-photo","reason":"The mount's own deck; the T-2 on it in the same set-up puts its footprint's middle 0.05 in further forward, within both ±."},"note":"Further forward than on the 1.57 in (0.28): the legs lean forward, and the taller mount's deck stands further ahead of its clamp."},"mount_length":{"label":"The clamp's length along the rail, at its foot","kind":"length","measurements":[{"id":"side-photo","value":1.547,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-193 c3827ed5c44c (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.93-side-SW0120.jpg: SW0120 alone on a rail section, straight left side, 1200 x 1200)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 306.5 and 890.0 (the gaps' edges on rows 700 to 724), six pitches apart (std.picatinny.slot_pitch): 97.25 px a pitch, 246.8 px/in at the rail's middle; the teeth's tops on row 697.5 (the white ground shows through the slots down to their floors: the photo is level)","method":"the clamp's foot under the rail's top (row 758), from the front leg's lower end (column 433.1) to the rear face (815): 381.9 px","via":"harvest"}}]},"clamp_front":{"label":"The clamp's foot, its front end ahead of the wheel's shaft","kind":"length","measurements":[{"id":"side-photo","value":0.669,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-193 c3827ed5c44c (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.93-side-SW0120.jpg: SW0120 alone on a rail section, straight left side, 1200 x 1200)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 306.5 and 890.0 (the gaps' edges on rows 700 to 724), six pitches apart (std.picatinny.slot_pitch): 97.25 px a pitch, 246.8 px/in at the rail's middle; the teeth's tops on row 697.5 (the white ground shows through the slots down to their floors: the photo is level)","method":"the traced outline's foot (profiles.side) ends at column 433.1, 165.1 px ahead of the shaft (598.25)","via":"harvest"}}]},"clamp_rear":{"label":"The clamp's foot, its rear end behind the wheel's shaft","kind":"length","measurements":[{"id":"side-photo","value":0.878,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-193 c3827ed5c44c (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.93-side-SW0120.jpg: SW0120 alone on a rail section, straight left side, 1200 x 1200)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 306.5 and 890.0 (the gaps' edges on rows 700 to 724), six pitches apart (std.picatinny.slot_pitch): 97.25 px a pitch, 246.8 px/in at the rail's middle; the teeth's tops on row 697.5 (the white ground shows through the slots down to their floors: the photo is level)","method":"the rear face, column 815, 216.75 px behind the shaft","via":"harvest"}}]},"length":{"label":"Overall length along the rail","kind":"length","measurements":[{"id":"side-photo","value":2.198,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-193 c3827ed5c44c (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.93-side-SW0120.jpg: SW0120 alone on a rail section, straight left side, 1200 x 1200)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 306.5 and 890.0 (the gaps' edges on rows 700 to 724), six pitches apart (std.picatinny.slot_pitch): 97.25 px a pitch, 246.8 px/in at the rail's middle; the teeth's tops on row 697.5 (the white ground shows through the slots down to their floors: the photo is level)","method":"the deck's front step (column 272.5) to the rear face (815): 542.5 px","via":"harvest"},"note":"As read: the near face reads about 1.3% large (rim_top_above_rail). No page gives this height's length."}]},"width":{"label":"Overall width across the clamp","kind":"length","measurements":[{"id":"drawing","value":1.334,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-193 c5d15b40764b (Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 29.8 mm's own lines 400.5 px apart (341.4): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. The drawing is the 1.57 in's stroke for stroke from the clamp up to the body's shoulders","method":"the clamp's two outer faces, the strokes at columns 373.5 and 827.5 (rows 950 to 1120): 454 px, about column 600.5, the rail's middle","via":"harvest"}}],"note":"The maker: \"the Leap mount is symmetrical, protruding less than 7mm from either side of your Picatinny rail.\" (under 1.386 in)."},"body_width":{"label":"The body under the deck, across (its two side walls' outer faces)","kind":"length","measurements":[{"id":"drawing","value":0.94,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-193 c5d15b40764b (Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 29.8 mm's own lines 400.5 px apart (341.4): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. The drawing is the 1.57 in's stroke for stroke from the clamp up to the body's shoulders","method":"the walls' strokes at columns 440.5 and 760.5 (rows 640 to 880): 320 px","via":"harvest"}}]},"clamp_below_rail":{"label":"The clamp's foot below the rail's top","kind":"length","measurements":[{"id":"drawing","value":0.234,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-193 c5d15b40764b (Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 29.8 mm's own lines 400.5 px apart (341.4): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. The drawing is the 1.57 in's stroke for stroke from the clamp up to the body's shoulders","method":"the jaws' feet (row 1170.5) under the extension line (1091): 79.5 px","via":"harvest"}},{"id":"side-photo","value":0.249,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-193 c3827ed5c44c (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.93-side-SW0120.jpg: SW0120 alone on a rail section, straight left side, 1200 x 1200)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 306.5 and 890.0 (the gaps' edges on rows 700 to 724), six pitches apart (std.picatinny.slot_pitch): 97.25 px a pitch, 246.8 px/in at the rail's middle; the teeth's tops on row 697.5 (the white ground shows through the slots down to their floors: the photo is level)","method":"the left jaw's foot (row 759) under the teeth's tops (697.5): 61.5 px","via":"harvest"}}],"adopt":{"from":"drawing","reason":"The finer reading; the photo agrees within the two ±."}},"wheel_d":{"label":"ClickDrive wheel, over its teeth","kind":"length","measurements":[{"id":"side-photo","value":0.631,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-193 c3827ed5c44c (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.93-side-SW0120.jpg: SW0120 alone on a rail section, straight left side, 1200 x 1200)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 306.5 and 890.0 (the gaps' edges on rows 700 to 724), six pitches apart (std.picatinny.slot_pitch): 97.25 px a pitch, 246.8 px/in at the rail's middle; the teeth's tops on row 697.5 (the white ground shows through the slots down to their floors: the photo is level)","method":"the teeth's tips 76.5 px above and 79.25 px below the wheel's centre (column 599.5, row 699.5): 155.75 px","via":"harvest"},"note":"The wheel's face is the nearest thing to the lens: as read, perhaps 1.3% large."}],"note":"Twenty teeth, as on the 1.57 in's (counted on this photo's upper half too: tips about 18 degrees apart)."},"wheel_root_d":{"label":"ClickDrive wheel, at the foot of its teeth","kind":"length","measurements":[{"id":"side-photo","value":0.523,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-193 c3827ed5c44c (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.93-side-SW0120.jpg: SW0120 alone on a rail section, straight left side, 1200 x 1200)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 306.5 and 890.0 (the gaps' edges on rows 700 to 724), six pitches apart (std.picatinny.slot_pitch): 97.25 px a pitch, 246.8 px/in at the rail's middle; the teeth's tops on row 697.5 (the white ground shows through the slots down to their floors: the photo is level)","method":"the valleys between the top teeth, 64.5 px from the centre","via":"harvest"}}]},"wheel_face_d":{"label":"ClickDrive wheel, the face inside its rim","kind":"length","measurements":[{"id":"side-photo","value":0.565,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-193 c3827ed5c44c (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.93-side-SW0120.jpg: SW0120 alone on a rail section, straight left side, 1200 x 1200)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 306.5 and 890.0 (the gaps' edges on rows 700 to 724), six pitches apart (std.picatinny.slot_pitch): 97.25 px a pitch, 246.8 px/in at the rail's middle; the teeth's tops on row 697.5 (the white ground shows through the slots down to their floors: the photo is level)","method":"the bright ring round the face, columns 530 to 669.5","via":"harvest"}}]},"wheel_hub_d":{"label":"ClickDrive wheel, the socket in its middle","kind":"length","measurements":[{"id":"side-photo","value":0.138,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-193 c3827ed5c44c (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.93-side-SW0120.jpg: SW0120 alone on a rail section, straight left side, 1200 x 1200)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 306.5 and 890.0 (the gaps' edges on rows 700 to 724), six pitches apart (std.picatinny.slot_pitch): 97.25 px a pitch, 246.8 px/in at the rail's middle; the teeth's tops on row 697.5 (the white ground shows through the slots down to their floors: the photo is level)","method":"the dark hole at the wheel's middle, columns 582.5 to 616.5","via":"harvest"}}]},"wheel_axis_above_rail":{"label":"ClickDrive wheel's axis above the rail's top","kind":"length","measurements":[{"id":"side-photo","value":-0.008,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-193 c3827ed5c44c (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.93-side-SW0120.jpg: SW0120 alone on a rail section, straight left side, 1200 x 1200)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 306.5 and 890.0 (the gaps' edges on rows 700 to 724), six pitches apart (std.picatinny.slot_pitch): 97.25 px a pitch, 246.8 px/in at the rail's middle; the teeth's tops on row 697.5 (the white ground shows through the slots down to their floors: the photo is level)","method":"the wheel's centre (row 699.5, its socket's middle) under the teeth's tops (697.5)","via":"harvest"},"note":"On the rail's top within the reading: the shaft half in the slot and half in the clamp's roof."}]},"wheel_outer_z":{"label":"ClickDrive wheel, its outer face left of the mount's middle","kind":"length","measurements":[{"id":"drawing","value":0.663,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-193 c5d15b40764b (Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 29.8 mm's own lines 400.5 px apart (341.4): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. The drawing is the 1.57 in's stroke for stroke from the clamp up to the body's shoulders","method":"the wheel's knurl drawn edge on under the left jaw's rounded corner, its outer edge at column 374.5, flush with the clamp's left face: 225.75 px from the rail's middle","via":"harvest"}}]},"wheel_thickness":{"label":"ClickDrive wheel, across","kind":"length","measurements":[{"id":"drawing","value":0.167,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-193 c5d15b40764b (Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 29.8 mm's own lines 400.5 px apart (341.4): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. The drawing is the 1.57 in's stroke for stroke from the clamp up to the body's shoulders","method":"the knurl drawn edge on, columns 374.5 to 431.5: 57 px","via":"harvest"}}]},"set_screw_z":{"label":"The set screw in the rear end (the ball detent's), left of the middle","kind":"length","measurements":[{"id":"drawing","value":0.579,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-193 c5d15b40764b (Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 29.8 mm's own lines 400.5 px apart (341.4): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. The drawing is the 1.57 in's stroke for stroke from the clamp up to the body's shoulders","method":"the concentric circles drawn low at the left (its centre at column 403, row 1093): 197.25 px left of the rail's middle","via":"harvest"}}],"note":"\"An integrated spring-loaded ball-detent exerts enough force against the crown to make it completely recoil proof.\" (the maker's page); the screw low in the rear end in Primary Arms' side photo of this height (9aea9c007ed8)."},"set_screw_d":{"label":"The set screw's hole in the rear end","kind":"length","measurements":[{"id":"drawing","value":0.106,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-193 c5d15b40764b (Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 29.8 mm's own lines 400.5 px apart (341.4): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. The drawing is the 1.57 in's stroke for stroke from the clamp up to the body's shoulders","method":"the outermost of its circles, columns 385 to 421","via":"harvest"}}]},"jaw_inner_z":{"label":"The telescoping jaw: where it is split from the right wall, right of the middle","kind":"length","measurements":[{"id":"drawing","value":0.51,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-193 c5d15b40764b (Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 29.8 mm's own lines 400.5 px apart (341.4): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. The drawing is the 1.57 in's stroke for stroke from the clamp up to the body's shoulders","method":"the two strokes up the right wall at columns 770.5 and 777.5 (rows 1025 to 1105): their middle, 173.75 px right of the rail's middle","via":"harvest"}}]},"jaw_top":{"label":"The telescoping jaw, its top above the rail's top","kind":"length","measurements":[{"id":"drawing","value":0.195,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-193 c5d15b40764b (Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 29.8 mm's own lines 400.5 px apart (341.4): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. The drawing is the 1.57 in's stroke for stroke from the clamp up to the body's shoulders","method":"the stroke across the right wall (row 1024.5, columns 770 to 828) above the extension line (1091)","via":"harvest"}}]},"hook_top":{"label":"The telescoping jaw, where it turns in under the rail's head (its top there, below the rail's top)","kind":"length","measurements":[{"id":"drawing","value":-0.056,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/scalarworks-leap-01-micro-193 c5d15b40764b (Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200)","scaleRef":"the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 29.8 mm's own lines 400.5 px apart (341.4): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. The drawing is the 1.57 in's stroke for stroke from the clamp up to the body's shoulders","method":"the two strokes up the right wall curve in at row 1108 to meet the rail's upper face: 17 px under the extension line, as a height","via":"harvest"}}]},"guide_pin_x":{"label":"The guide pins' heads on the jaw's outer face, ahead of and behind the shaft's","kind":"length","measurements":[{"id":"leap-02","value":0.53,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{scalarworks-leap-02-micro-226.guide_pin_x}","via":"harvest"}}],"note":"No view of this mount's right side is on file: the LEAP/02's (Primary Arms' photo of it from the right front, 4945353b7bdf), on the same ClickDrive clamp, is the only one of the family's."},"guide_pin_d":{"label":"A guide pin's head","kind":"length","measurements":[{"id":"leap-02","value":0.1,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{scalarworks-leap-02-micro-226.guide_pin_d}","via":"harvest"},"note":"The LEAP/02's, as guide_pin_x."}]},"shaft_end_d":{"label":"The shaft's end on the jaw's outer face","kind":"length","measurements":[{"id":"leap-02","value":0.15,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{scalarworks-leap-02-micro-226.shaft_end_d}","via":"harvest"},"note":"The LEAP/02's, as guide_pin_x."}]},"head_ring":{"label":"The dark ring round each head in the jaw's face","kind":"length","measurements":[{"id":"leap-02","value":0.008,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{scalarworks-leap-02-micro-226.head_ring}","via":"harvest"},"note":"The LEAP/02's, as guide_pin_x."}]},"head_hole_depth":{"label":"How deep each head's hole is drawn","kind":"length","measurements":[{"id":"assumed","value":0.04,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the heads are flush with the face in the photo, and what is behind them doesn't show.","via":"harvest"}}]},"wheel_pocket_gap":{"label":"Clearance round the wheel in its pocket in the left wall","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the side photo shows the pocket's rim round the wheel's teeth as a dark ring a few pixels wide, which no scale on file resolves.","via":"harvest"}}]},"wheel_dish_depth":{"label":"How far the wheel's face is dished inside its rim","kind":"length","measurements":[{"id":"assumed","value":0.01,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the side photo shows the face's rim as a bright ring, its depth not.","via":"harvest"}}]},"wheel_socket_depth":{"label":"The socket in the wheel's middle, its depth","kind":"length","measurements":[{"id":"assumed","value":0.08,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the socket shows dark in the side photo, its depth not.","via":"harvest"}}]},"set_screw_hole_depth":{"label":"The set screw's hole in the rear end, its depth","kind":"length","measurements":[{"id":"assumed","value":0.1,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the drawing has the hole end on.","via":"harvest"}}]},"set_screw_recess":{"label":"How far the set screw's end stands back in its hole","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the photos show the screw's end just inside the hole's rim.","via":"harvest"}}]},"edge_break":{"label":"The aluminium's edges, broken","kind":"length","measurements":[{"id":"assumed","value":0.008,"unit":"in","pm":0.005,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the photos show every edge of the body softened, by an amount no view on file resolves.","via":"harvest"}}]},"weight":{"label":"Weight (the mount alone)","kind":"mass","measurements":[{"id":"page","value":51,"unit":"g","stated":"Weight SW0100 : 43g (1.52oz) SW0110 : 45g (1.58oz) SW0120 : 51g (1.80oz)","source":{"type":"spec","publisher":"manufacturer","name":"Scalarworks, LEAP/01 (product page, SPECIFICATIONS)","url":"https://scalarworks.com/shop/quick-detach-mounts/leap-01/","retrieved":"2026-11-03","via":"harvest"}},{"id":"trex","value":1.8,"unit":"oz","pm":0.005,"stated":"1.93\" Mount 1.80 oz.","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, Scalarworks LEAP/01 Aimpoint Micro T-2 QD Mount","url":"https://www.trex-arms.com/store/scalarworks-leap-01-aimpoint-micro-t-2-qd-mount-73479","retrieved":"2026-11-03","via":"harvest"}},{"id":"midway","value":1.65,"unit":"oz","stated":"Weight 1.65 Ounce","source":{"type":"spec","publisher":"retailer","name":"MidwayUSA, Scalarworks LEAP Aimpoint Micro QD Picatinny Red Dot Mount (product 1022884560)","url":"https://www.midwayusa.com/product/1022884560","retrieved":"2026-11-03","via":"harvest"},"note":"One figure for a page that sells the 1.57 and the 1.93 in."}],"adopt":{"from":"page","reason":"The maker's figure for this height; T.REX ARMS quotes it in ounces. MidwayUSA's is one figure for two heights."}}}},{"subject":"scalarworks-leap-02-micro-226","title":"Scalarworks LEAP/02 Aimpoint Micro T-2 quick-detach mount, 2.26 in (SW0230, SW0230-FDE)","dimensions":{"optical_axis_above_rail":{"label":"Optical axis above the rail's top, with an Aimpoint Micro T-2 on it (the maker's height)","kind":"length","measurements":[{"id":"page","value":2.26,"unit":"in","stated":"Optic center height over rail 2.26\"","source":{"type":"spec","publisher":"manufacturer","name":"Scalarworks, LEAP/02 (product page, SPECIFICATIONS)","url":"https://scalarworks.com/shop/quick-detach-mounts/leap-02/","retrieved":"2026-11-03","via":"harvest"}}],"note":"The page is for the T-2: \"LEAP/02 redefines the standard for mounting your Aimpoint Micro T2 footprint optic at 2.26\" height.\"; its markup: \"The Scalarworks LEAP/02 is a lightweight modular 2.26 inch height quick-detach mount for Aimpoint Micro T2 compatible red dot sights.\" Its co-witness, in the same table: \"Co-Witness None (A2 BUIS visible through base)\"; and \"You can also co-witness backup iron sights at 2.26\" height with a 6\" sight radius.\" (with the maker's KICK/09 \"Diving Boards\")."},"deck_above_rail":{"label":"The deck's floor (where the dot's base sits) above the rail's top","kind":"length","measurements":[{"id":"less-t2","value":1.671,"unit":"in","pm":0.037,"source":{"type":"derived","expr":"{.optical_axis_above_rail} - {aimpoint-micro-t-2.axis_above_base}","via":"harvest"},"note":"2.26 in less the T-2's 0.589 in."}],"note":"The deck is the LEAP/01's: a floor between two rims, the lug standing up in its middle and four screw holes (Primary Arms' photo of this mount from above, 4945353b7bdf). The maker states only the axis's height, for the T-2: the floor is that less the T-2's axis over its base (D101). No drawing of this mount is on file to read the floor on; its side photo has the rims' top (rim_top_above_rail)."},"rim_top_above_rail":{"label":"The deck's two rims, their tops above the rail's top","kind":"length","measurements":[{"id":"side-photo","value":1.734,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/scalarworks-leap-02-micro-226 9b13a0aaeb23 (Scalarworks, scalarworks-leap-02-quick-detach-Aimpoint-Micro-T2-mount-side-SW0230-1.jpg: SW0230 alone on a rail section, straight left side, 2000 x 2000)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 532.5 and 1475.0 (the gaps' edges on rows 1125 to 1160), six pitches apart (std.picatinny.slot_pitch): 157.08 px a pitch, 398.7 px/in at the rail's middle; the teeth's tops on row 1118 (the white ground shows through the slots down to their floors, 46 px lower: the photo is level)","method":"the mount's top edge (row 426.5, from column 518 to 1228) above the teeth's tops: 691.5 px","via":"harvest"}}],"note":"Not drawn above the deck's floor (the part's approximations). On the LEAP/01's drawings the rims stand 0.078 to 0.081 in over the floor: here 1.734 less that is 1.65 to 1.66 in for the floor, which the photo's 1.3% (the near face reads large, as the LEAP/01's photos do) takes to 1.63; the floor the T-2's figure gives is 1.671 ± 0.037."},"deck_x":{"label":"The footprint's middle along the deck, ahead of the wheel's shaft","kind":"length","measurements":[{"id":"side-photo","value":0.328,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/scalarworks-leap-02-micro-226 9b13a0aaeb23 (Scalarworks, scalarworks-leap-02-quick-detach-Aimpoint-Micro-T2-mount-side-SW0230-1.jpg: SW0230 alone on a rail section, straight left side, 2000 x 2000)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 532.5 and 1475.0 (the gaps' edges on rows 1125 to 1160), six pitches apart (std.picatinny.slot_pitch): 157.08 px a pitch, 398.7 px/in at the rail's middle; the teeth's tops on row 1118 (the white ground shows through the slots down to their floors, 46 px lower: the photo is level)","method":"the middle of the rims' flat top, between the notch at its front tip (column 518) and its rear end over the rear post (1228): column 873, 130.75 px ahead of the wheel's shaft (column 1003.75, the slot midway). The lug in the middle of the deck: Primary Arms' photo from above (4945353b7bdf)","via":"harvest"}}]},"mount_length":{"label":"The clamp's length along the rail, at its foot","kind":"length","measurements":[{"id":"side-photo","value":1.771,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/scalarworks-leap-02-micro-226 9b13a0aaeb23 (Scalarworks, scalarworks-leap-02-quick-detach-Aimpoint-Micro-T2-mount-side-SW0230-1.jpg: SW0230 alone on a rail section, straight left side, 2000 x 2000)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 532.5 and 1475.0 (the gaps' edges on rows 1125 to 1160), six pitches apart (std.picatinny.slot_pitch): 157.08 px a pitch, 398.7 px/in at the rail's middle; the teeth's tops on row 1118 (the white ground shows through the slots down to their floors, 46 px lower: the photo is level)","method":"the traced outline's foot (profiles.side), from 0.887 in ahead of the shaft to 0.884 in behind it","via":"harvest"},"note":"As read: the near face reads about 1.3% large on the LEAP/01's photos of the same set-up."}]},"clamp_front":{"label":"The clamp's foot, its front end ahead of the wheel's shaft","kind":"length","measurements":[{"id":"side-photo","value":0.887,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/scalarworks-leap-02-micro-226 9b13a0aaeb23 (Scalarworks, scalarworks-leap-02-quick-detach-Aimpoint-Micro-T2-mount-side-SW0230-1.jpg: SW0230 alone on a rail section, straight left side, 2000 x 2000)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 532.5 and 1475.0 (the gaps' edges on rows 1125 to 1160), six pitches apart (std.picatinny.slot_pitch): 157.08 px a pitch, 398.7 px/in at the rail's middle; the teeth's tops on row 1118 (the white ground shows through the slots down to their floors, 46 px lower: the photo is level)","method":"the traced outline's foot (profiles.side): its front end, 0.887 in ahead of the shaft (column 650)","via":"harvest"}}]},"clamp_rear":{"label":"The clamp's foot, its rear end behind the wheel's shaft","kind":"length","measurements":[{"id":"side-photo","value":0.884,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/scalarworks-leap-02-micro-226 9b13a0aaeb23 (Scalarworks, scalarworks-leap-02-quick-detach-Aimpoint-Micro-T2-mount-side-SW0230-1.jpg: SW0230 alone on a rail section, straight left side, 2000 x 2000)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 532.5 and 1475.0 (the gaps' edges on rows 1125 to 1160), six pitches apart (std.picatinny.slot_pitch): 157.08 px a pitch, 398.7 px/in at the rail's middle; the teeth's tops on row 1118 (the white ground shows through the slots down to their floors, 46 px lower: the photo is level)","method":"the rear face of the clamp's block at its foot, column 1356.25: 352.5 px behind the shaft (the outline's own corner is at 0.886 in)","via":"harvest"}}]},"length":{"label":"Overall length along the rail","kind":"length","measurements":[{"id":"side-photo","value":2.209,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/scalarworks-leap-02-micro-226 9b13a0aaeb23 (Scalarworks, scalarworks-leap-02-quick-detach-Aimpoint-Micro-T2-mount-side-SW0230-1.jpg: SW0230 alone on a rail section, straight left side, 2000 x 2000)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 532.5 and 1475.0 (the gaps' edges on rows 1125 to 1160), six pitches apart (std.picatinny.slot_pitch): 157.08 px a pitch, 398.7 px/in at the rail's middle; the teeth's tops on row 1118 (the white ground shows through the slots down to their floors, 46 px lower: the photo is level)","method":"the traced outline (profiles.side): the deck's front tip 1.325 in ahead of the shaft, the clamp's rear face 0.884 in behind it (column 1356.25)","via":"harvest"},"note":"No page gives it."}]},"width":{"label":"Overall width across the clamp","kind":"length","measurements":[{"id":"leap-01","value":1.334,"unit":"in","pm":0.006,"source":{"type":"derived","expr":"{scalarworks-leap-01-micro-193.width}","via":"harvest"},"note":"The LEAP/01 1.93 in's drawing from behind: the only view across a mount of this family on file."}],"note":"The LEAP/02's page: \"the Leap mount is symmetrical, protruding less than 7mm from either side of your Picatinny rail.\" No view across this mount is on file: read on the LEAP/01's drawing, the same ClickDrive clamp."},"body_width":{"label":"The body under the deck, across (its two side walls' outer faces)","kind":"length","measurements":[{"id":"leap-01","value":0.94,"unit":"in","pm":0.006,"source":{"type":"derived","expr":"{scalarworks-leap-01-micro-193.body_width}","via":"harvest"},"note":"The LEAP/01's, as width: the deck carries the same footprint and its walls stand under its rims in Primary Arms' photo from above."}]},"end_raise":{"label":"How far the LEAP/01 1.93 in's section is lengthened up its walls for this mount's","kind":"length","measurements":[{"id":"decks","value":0.33,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.deck_above_rail} - {scalarworks-leap-01-micro-193.deck_above_rail}","via":"harvest"}}],"note":"The section across is the LEAP/01's (profiles.end, from that mount's drawing); this mount's deck stands higher. The model raises everything of that section over the middle of its straight walls by this much, the window through the ends with it (the LEAP/02's runs the frame's height: \"A2 BUIS visible through base\", and Primary Arms' photo from the front)."},"clamp_below_rail":{"label":"The clamp's foot below the rail's top","kind":"length","measurements":[{"id":"side-photo","value":0.236,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/scalarworks-leap-02-micro-226 9b13a0aaeb23 (Scalarworks, scalarworks-leap-02-quick-detach-Aimpoint-Micro-T2-mount-side-SW0230-1.jpg: SW0230 alone on a rail section, straight left side, 2000 x 2000)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 532.5 and 1475.0 (the gaps' edges on rows 1125 to 1160), six pitches apart (std.picatinny.slot_pitch): 157.08 px a pitch, 398.7 px/in at the rail's middle; the teeth's tops on row 1118 (the white ground shows through the slots down to their floors, 46 px lower: the photo is level)","method":"the clamp's foot (row 1212, its dark edge under the wheel's sides) under the teeth's tops (1118): 94 px","via":"harvest"}}]},"wheel_d":{"label":"ClickDrive wheel, over its teeth","kind":"length","measurements":[{"id":"side-photo","value":0.627,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/scalarworks-leap-02-micro-226 9b13a0aaeb23 (Scalarworks, scalarworks-leap-02-quick-detach-Aimpoint-Micro-T2-mount-side-SW0230-1.jpg: SW0230 alone on a rail section, straight left side, 2000 x 2000)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 532.5 and 1475.0 (the gaps' edges on rows 1125 to 1160), six pitches apart (std.picatinny.slot_pitch): 157.08 px a pitch, 398.7 px/in at the rail's middle; the teeth's tops on row 1118 (the white ground shows through the slots down to their floors, 46 px lower: the photo is level)","method":"the bottom teeth's tips (row 1255.8) under the wheel's socket's middle (column 1004.2, row 1130.8): 125 px, twice","via":"harvest"}}]},"wheel_root_d":{"label":"ClickDrive wheel, at the foot of its teeth","kind":"length","measurements":[{"id":"side-photo","value":0.577,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/scalarworks-leap-02-micro-226 9b13a0aaeb23 (Scalarworks, scalarworks-leap-02-quick-detach-Aimpoint-Micro-T2-mount-side-SW0230-1.jpg: SW0230 alone on a rail section, straight left side, 2000 x 2000)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 532.5 and 1475.0 (the gaps' edges on rows 1125 to 1160), six pitches apart (std.picatinny.slot_pitch): 157.08 px a pitch, 398.7 px/in at the rail's middle; the teeth's tops on row 1118 (the white ground shows through the slots down to their floors, 46 px lower: the photo is level)","method":"the valleys between the bottom teeth (row 1246), 115 px under the centre, twice","via":"harvest"}}]},"wheel_face_d":{"label":"ClickDrive wheel, the face inside its rim","kind":"length","measurements":[{"id":"side-photo","value":0.54,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/scalarworks-leap-02-micro-226 9b13a0aaeb23 (Scalarworks, scalarworks-leap-02-quick-detach-Aimpoint-Micro-T2-mount-side-SW0230-1.jpg: SW0230 alone on a rail section, straight left side, 2000 x 2000)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 532.5 and 1475.0 (the gaps' edges on rows 1125 to 1160), six pitches apart (std.picatinny.slot_pitch): 157.08 px a pitch, 398.7 px/in at the rail's middle; the teeth's tops on row 1118 (the white ground shows through the slots down to their floors, 46 px lower: the photo is level)","method":"the bright ring round the face, columns 896.5 to 1112","via":"harvest"}}]},"wheel_hub_d":{"label":"ClickDrive wheel, the socket in its middle","kind":"length","measurements":[{"id":"side-photo","value":0.122,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/scalarworks-leap-02-micro-226 9b13a0aaeb23 (Scalarworks, scalarworks-leap-02-quick-detach-Aimpoint-Micro-T2-mount-side-SW0230-1.jpg: SW0230 alone on a rail section, straight left side, 2000 x 2000)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 532.5 and 1475.0 (the gaps' edges on rows 1125 to 1160), six pitches apart (std.picatinny.slot_pitch): 157.08 px a pitch, 398.7 px/in at the rail's middle; the teeth's tops on row 1118 (the white ground shows through the slots down to their floors, 46 px lower: the photo is level)","method":"the dark hole at the wheel's middle, columns 980 to 1028.5","via":"harvest"}}]},"wheel_axis_above_rail":{"label":"ClickDrive wheel's axis above the rail's top","kind":"length","measurements":[{"id":"side-photo","value":-0.032,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/scalarworks-leap-02-micro-226 9b13a0aaeb23 (Scalarworks, scalarworks-leap-02-quick-detach-Aimpoint-Micro-T2-mount-side-SW0230-1.jpg: SW0230 alone on a rail section, straight left side, 2000 x 2000)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 532.5 and 1475.0 (the gaps' edges on rows 1125 to 1160), six pitches apart (std.picatinny.slot_pitch): 157.08 px a pitch, 398.7 px/in at the rail's middle; the teeth's tops on row 1118 (the white ground shows through the slots down to their floors, 46 px lower: the photo is level)","method":"the wheel's socket's middle (row 1130.8) under the teeth's tops (1118): 12.8 px","via":"harvest"},"note":"Lower than the LEAP/01's (0.002 to -0.008 in their photos): read as it is."}]},"wheel_outer_z":{"label":"ClickDrive wheel, its outer face left of the mount's middle","kind":"length","measurements":[{"id":"leap-01","value":0.663,"unit":"in","pm":0.006,"source":{"type":"derived","expr":"{scalarworks-leap-01-micro-193.wheel_outer_z}","via":"harvest"},"note":"No view across this mount on file: the LEAP/01's drawing, the same ClickDrive clamp and wheel."}]},"wheel_thickness":{"label":"ClickDrive wheel, across","kind":"length","measurements":[{"id":"leap-01","value":0.167,"unit":"in","pm":0.008,"source":{"type":"derived","expr":"{scalarworks-leap-01-micro-193.wheel_thickness}","via":"harvest"},"note":"The LEAP/01's drawing, as wheel_outer_z."}]},"set_screw_z":{"label":"The set screw in the rear end (the ball detent's), left of the middle","kind":"length","measurements":[{"id":"leap-01","value":0.579,"unit":"in","pm":0.008,"source":{"type":"derived","expr":"{scalarworks-leap-01-micro-193.set_screw_z}","via":"harvest"},"note":"The LEAP/01's drawing: no view of this mount's rear end on file."}],"note":"\"An integrated spring-loaded ball-detent exerts enough force against the crown to make it completely recoil proof.\" (the LEAP/01's page; this one: \"ClickDrive's low-profile thumbscrew and low-friction telescoping clamp ...\"); the screw's hole shows low in the rear block in the side photo."},"set_screw_d":{"label":"The set screw's hole in the rear end","kind":"length","measurements":[{"id":"leap-01","value":0.106,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{scalarworks-leap-01-micro-193.set_screw_d}","via":"harvest"},"note":"The LEAP/01's drawing, as set_screw_z."}]},"jaw_inner_z":{"label":"The telescoping jaw: where it is split from the right wall, right of the middle","kind":"length","measurements":[{"id":"leap-01","value":0.51,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{scalarworks-leap-01-micro-193.jaw_inner_z}","via":"harvest"},"note":"The LEAP/01's drawing: the same clamp (Primary Arms' photo of this mount's right side shows the jaw's split low along it, with the shaft's end and the two guide pins' in a row)."}]},"jaw_top":{"label":"The telescoping jaw, its top above the rail's top","kind":"length","measurements":[{"id":"leap-01","value":0.195,"unit":"in","pm":0.006,"source":{"type":"derived","expr":"{scalarworks-leap-01-micro-193.jaw_top}","via":"harvest"},"note":"The LEAP/01's drawing, as jaw_inner_z."}]},"hook_top":{"label":"The telescoping jaw, where it turns in under the rail's head (its top there, below the rail's top)","kind":"length","measurements":[{"id":"leap-01","value":-0.056,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{scalarworks-leap-01-micro-193.hook_top}","via":"harvest"},"note":"The LEAP/01's drawing, as jaw_inner_z."}]},"window_step":{"label":"The stepped recess round the side window: each step's width","kind":"length","measurements":[{"id":"side-photo","value":0.027,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/scalarworks-leap-02-micro-226 9b13a0aaeb23 (Scalarworks, scalarworks-leap-02-quick-detach-Aimpoint-Micro-T2-mount-side-SW0230-1.jpg: SW0230 alone on a rail section, straight left side, 2000 x 2000)","scaleRef":"the rail section's own slots: the gaps of the two that show have their middles at columns 532.5 and 1475.0 (the gaps' edges on rows 1125 to 1160), six pitches apart (std.picatinny.slot_pitch): 157.08 px a pitch, 398.7 px/in at the rail's middle; the teeth's tops on row 1118 (the white ground shows through the slots down to their floors, 46 px lower: the photo is level)","method":"the steps' lit edges down the window's front side, on row 620: columns 870, 882 and 893, the window's edge at 905 (11.5 px a step); across its top, on column 960: rows 515, 525 and 533, the edge at 540 (9 px a step): 10.4 px","via":"harvest"}}],"note":"Three steps round the window in each side face, counted on the side photo (each step's edge catches the light) and in Primary Arms' photo of the right side (4945353b7bdf)."},"window_step_depth":{"label":"The stepped recess round the side window: each step's depth","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file looks along a step; Primary Arms' oblique (4945353b7bdf) shows them about as deep as they are wide.","via":"harvest"}}]},"guide_pin_x":{"label":"The guide pins' heads on the jaw's outer face, ahead of and behind the shaft's","kind":"length","measurements":[{"id":"pa-photo","value":0.53,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/scalarworks-leap-02-micro-226 4945353b7bdf (Primary Arms, SW0230_01.jpg: SW0230 alone from the right front and above, 2200 x 1467)","scaleRef":"the jaw's own length along its lower edge (columns 517 to 1276: 819 px along the edge's line), clamp_front plus clamp_rear: a proportion in an oblique, the heads on the same face as the edge","method":"the heads' middles at (603, 1083), (830, 1175) and (1055, 1268): 245 and 243 px apart along the edge's line","via":"harvest"}}],"note":"Three round heads in a row along the right jaw, evenly spaced, the largest in the middle where the shaft ends: \"A pair of hardened steel precision ground pins is press fitted to the clamp and act as guides.\" (the LEAP/01's page; the maker's render of the ClickDrive clamp draws the two pins across the jaw either side of the shaft, 7519a621ec0e)."},"guide_pin_d":{"label":"A guide pin's head","kind":"length","measurements":[{"id":"pa-photo","value":0.1,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/scalarworks-leap-02-micro-226 4945353b7bdf (Primary Arms, SW0230_01.jpg: SW0230 alone from the right front and above, 2200 x 1467)","scaleRef":"the jaw's own length along its lower edge (columns 517 to 1276: 819 px along the edge's line), clamp_front plus clamp_rear: a proportion in an oblique, the heads on the same face as the edge","method":"the front head across the edge's line, columns 580 to 626: 46 px","via":"harvest"}}]},"shaft_end_d":{"label":"The shaft's end on the jaw's outer face","kind":"length","measurements":[{"id":"pa-photo","value":0.15,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/scalarworks-leap-02-micro-226 4945353b7bdf (Primary Arms, SW0230_01.jpg: SW0230 alone from the right front and above, 2200 x 1467)","scaleRef":"the jaw's own length along its lower edge (columns 517 to 1276: 819 px along the edge's line), clamp_front plus clamp_rear: a proportion in an oblique, the heads on the same face as the edge","method":"the middle head across the edge's line, columns 795 to 865: 70 px","via":"harvest"}}]},"head_ring":{"label":"The dark ring round each head in the jaw's face","kind":"length","measurements":[{"id":"pa-photo","value":0.008,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/scalarworks-leap-02-micro-226 4945353b7bdf (Primary Arms, SW0230_01.jpg: SW0230 alone from the right front and above, 2200 x 1467)","scaleRef":"the jaw's own length along its lower edge (columns 517 to 1276: 819 px along the edge's line), clamp_front plus clamp_rear: a proportion in an oblique, the heads on the same face as the edge","method":"the dark ring round the middle head, about 4 px wide","via":"harvest"}}]},"head_hole_depth":{"label":"How deep each head's hole is drawn","kind":"length","measurements":[{"id":"assumed","value":0.04,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the heads are flush with the face in the photo, and what is behind them doesn't show.","via":"harvest"}}]},"wheel_pocket_gap":{"label":"Clearance round the wheel in its pocket in the left wall","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the side photo shows the pocket's rim round the wheel's teeth as a dark ring a few pixels wide.","via":"harvest"}}]},"wheel_dish_depth":{"label":"How far the wheel's face is dished inside its rim","kind":"length","measurements":[{"id":"assumed","value":0.01,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file has the wheel in profile.","via":"harvest"}}]},"wheel_socket_depth":{"label":"The socket in the wheel's middle, its depth","kind":"length","measurements":[{"id":"assumed","value":0.08,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the socket shows dark in the side photo, its depth not.","via":"harvest"}}]},"set_screw_hole_depth":{"label":"The set screw's hole in the rear end, its depth","kind":"length","measurements":[{"id":"assumed","value":0.1,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file looks into it.","via":"harvest"}}]},"set_screw_recess":{"label":"How far the set screw's end stands back in its hole","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading.","via":"harvest"}}]},"edge_break":{"label":"The aluminium's edges, broken","kind":"length","measurements":[{"id":"assumed","value":0.008,"unit":"in","pm":0.005,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the photos show every edge of the body softened, by an amount no view on file resolves.","via":"harvest"}}]},"weight":{"label":"Weight (the mount alone)","kind":"mass","measurements":[{"id":"page","value":63,"unit":"g","stated":"Weight 63g (2.22oz)","source":{"type":"spec","publisher":"manufacturer","name":"Scalarworks, LEAP/02 (product page, SPECIFICATIONS)","url":"https://scalarworks.com/shop/quick-detach-mounts/leap-02/","retrieved":"2026-11-03","via":"harvest"}},{"id":"chart","value":63,"unit":"g","stated":"Scalarworks ® LEAP™ SW0230 (63grams)","source":{"type":"spec","publisher":"manufacturer","name":"Scalarworks, LEAP/02 (product page, SPECIFICATIONS)","url":"https://scalarworks.com/shop/quick-detach-mounts/leap-02/","retrieved":"2026-11-03","via":"harvest"},"note":"The page's chart: \"All parts weighed under the same conditions including rail screws.\""}],"adopt":{"from":"page","reason":"The maker's figure; its chart weighs the same."}}}},{"subject":"scalarworks-leap-08-30mm-mount","title":"Scalarworks LEAP/08, 30 mm, 1.57 in (SW0815)","dimensions":{"optical_axis_above_rail":{"label":"Ring axis above the rail's top","kind":"length","measurements":[{"id":"page","value":1.57,"unit":"in","stated":"Optic center height over rail SW0815 : 1.57\" SW0825 : 1.93\"","source":{"type":"spec","publisher":"manufacturer","name":"Scalarworks, LEAP/08 (product page, SPECIFICATIONS)","url":"https://scalarworks.com/shop/quick-detach-mounts/leap-08/","retrieved":"2026-10-13","via":"harvest"},"note":"The same page, at the choice of height: \"Height — Optic center from top of Rail. 1.57\" 1.93\"\"."},{"id":"drawing","value":40,"unit":"mm","stated":"40","source":{"type":"spec","publisher":"manufacturer","name":"Scalarworks, the technical drawing of SW0815 in the LEAP/08 page's gallery for the 1.57 in height (\"*All dimensions are in millimeters unless otherwise noted.\"; references/scalarworks-leap-08-30mm-mount f533e2d6d088)","url":"https://scalarworks.com/wp-content/uploads/scalarworks-leap-08-1.57in-height-30mm-scope-mount-dimensions-SW0815.png","retrieved":"2026-10-13","via":"harvest"},"note":"From the rail's top line to the rings' centre line. A whole number of millimetres: ± 0.5."},{"id":"as-drawn","value":40.4,"unit":"mm","pm":0.2,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"the centre line (row 954, midway between the two bore lines at 797.5 and 1111, and the row of the rings' split) to the lower extension line of the \"40\", which is the rail's top line (row 1376.5): 422.5 px. The base's own underside between the clamps is drawn at row 1374.5, 0.2 mm above that line","via":"harvest"}},{"id":"side-photo","value":40.4,"unit":"mm","pm":0.4,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount b723449f6856 (Scalarworks, scalarworks-leap-08-gen3-quick-detach-mount-1.57-side-SW0815-A.jpg: SW0815 alone on a rail section, straight left side, 2000 x 2000)","scaleRef":"the rail section's own slots: four show (their centres at columns 689.6, 786.3, 1173.8 and 1367.3: slots 0, 1, 5 and 7), 96.81 px a pitch (std.picatinny.slot_pitch: 9.674 px/mm), the same within 0.1% at the left end and under the mount's middle","method":"the dark line of each ring's split (row 850.5 in both rings: the photo is level) to the tops of the rail's teeth (row 1242.9, read at two teeth 480 px apart): 392.4 px is 40.56 mm; less about 2.5 px for the split standing nearer the lens than the rail's middle and above the lens's axis","via":"harvest"}}],"adopt":{"from":"page","reason":"The maker's stated centreline height, which is what the category asks for and what a buyer compares; its drawing's own \"40\" rounds to it. The drawing's lines and the side photo both put the axis 0.02 in higher: kept beside it, and said in the part's notes."},"note":"FOUR READINGS, TWO PAIRS. The maker says 1.57 in in words and \"40\" (mm, 1.575 in) on its drawing. The drawing's own lines for that dimension are 40.40 mm apart at the scale its other dimensions keep (1.590 in), and the maker's side photo has the rings' split 40.3 to 40.6 mm above the rail's teeth by the rail's own pitch. So the mount as drawn and as photographed stands about half a millimetre (0.02 in) higher than the figure it is sold by. The figure is the maker's and is the one a buyer compares; the model's rings are on it, and its foot is seated on the rail (lib.rail_seat), which takes up the difference inside the base."},"ring_bore":{"label":"Tube diameter the rings are bored for","kind":"length","measurements":[{"id":"page","value":30,"unit":"mm","stated":"Ring diameter 30mm","source":{"type":"spec","publisher":"manufacturer","name":"Scalarworks, LEAP/08 (product page, SPECIFICATIONS)","url":"https://scalarworks.com/shop/quick-detach-mounts/leap-08/","retrieved":"2026-10-13","via":"harvest"}},{"id":"drawing","value":30,"unit":"mm","stated":"30ø","source":{"type":"spec","publisher":"manufacturer","name":"Scalarworks, the technical drawing of SW0815 in the LEAP/08 page's gallery for the 1.57 in height (\"*All dimensions are in millimeters unless otherwise noted.\"; references/scalarworks-leap-08-30mm-mount f533e2d6d088)","url":"https://scalarworks.com/wp-content/uploads/scalarworks-leap-08-1.57in-height-30mm-scope-mount-dimensions-SW0815.png","retrieved":"2026-10-13","via":"harvest"}}],"adopt":{"from":"page","reason":"The maker's page; its drawing says the same."}},"ring_length":{"label":"Each ring's length along the tube (face to face)","kind":"length","measurements":[{"id":"drawing","value":24,"unit":"mm","stated":"24","source":{"type":"spec","publisher":"manufacturer","name":"Scalarworks, the technical drawing of SW0815 in the LEAP/08 page's gallery for the 1.57 in height (\"*All dimensions are in millimeters unless otherwise noted.\"; references/scalarworks-leap-08-30mm-mount f533e2d6d088)","url":"https://scalarworks.com/wp-content/uploads/scalarworks-leap-08-1.57in-height-30mm-scope-mount-dimensions-SW0815.png","retrieved":"2026-10-13","via":"harvest"},"note":"Stated over each ring, between extension lines on its two end faces."},{"id":"side-photo","value":23.95,"unit":"mm","pm":0.3,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount b723449f6856 (Scalarworks, scalarworks-leap-08-gen3-quick-detach-mount-1.57-side-SW0815-A.jpg: SW0815 alone on a rail section, straight left side, 2000 x 2000)","scaleRef":"the rail section's own slots: four show (their centres at columns 689.6, 786.3, 1173.8 and 1367.3: slots 0, 1, 5 and 7), 96.81 px a pitch (std.picatinny.slot_pitch: 9.674 px/mm), the same within 0.1% at the left end and under the mount's middle","method":"each ring's lower half between its two end faces' edges, rows 930 and 1000: 231.4 px (front ring) and 232.2 px (rear ring)","via":"harvest"},"note":"The check of the drawing's scale against the rail's: 0.2% apart."}],"adopt":{"from":"drawing","reason":"The maker's own dimension; the side photo, scaled by the rail under it, reads the same."},"note":"The page's words for it: \"BROAD: 22% wider than standard ring designs to provide a mechanically superior secondary optic platform.\""},"ring_gap":{"label":"Between the two rings, face to face","kind":"length","measurements":[{"id":"drawing","value":60,"unit":"mm","stated":"60","source":{"type":"spec","publisher":"manufacturer","name":"Scalarworks, the technical drawing of SW0815 in the LEAP/08 page's gallery for the 1.57 in height (\"*All dimensions are in millimeters unless otherwise noted.\"; references/scalarworks-leap-08-30mm-mount f533e2d6d088)","url":"https://scalarworks.com/wp-content/uploads/scalarworks-leap-08-1.57in-height-30mm-scope-mount-dimensions-SW0815.png","retrieved":"2026-10-13","via":"harvest"},"note":"From the front ring's rear face to the rear ring's front face: what a scope's turret saddle has to fit between. The two rings' middles are 84 mm apart."}]},"tube_to_beam":{"label":"Under the tube: the bore's lowest line to the beam's top between the rings","kind":"length","measurements":[{"id":"drawing","value":10,"unit":"mm","stated":"10","source":{"type":"spec","publisher":"manufacturer","name":"Scalarworks, the technical drawing of SW0815 in the LEAP/08 page's gallery for the 1.57 in height (\"*All dimensions are in millimeters unless otherwise noted.\"; references/scalarworks-leap-08-30mm-mount f533e2d6d088)","url":"https://scalarworks.com/wp-content/uploads/scalarworks-leap-08-1.57in-height-30mm-scope-mount-dimensions-SW0815.png","retrieved":"2026-10-13","via":"harvest"}},{"id":"as-drawn","value":10.37,"unit":"mm","pm":0.15,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"the lower bore line (row 1111) to the beam's top edge between the rings (row 1219.5): 108.5 px","via":"harvest"},"note":"As with the \"40\": drawn 0.4 mm more than the whole number says."}],"adopt":{"from":"drawing","reason":"The maker's stated figure; what the model's beam stands at is the traced outline's, which is the drawing's lines."}},"ring_rear_x":{"label":"Rear ring, its middle ahead of the rear clamp's shaft","kind":"length","measurements":[{"id":"as-drawn","value":30,"unit":"mm","pm":0.15,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"the rear ring's middle (its end faces at columns 1221 and 1472.5: 1346.75) to the rear wheel's centre (column 1660.54, the centroid of the two circles drawn at its middle): 313.8 px","via":"harvest"},"note":"The side photo has the same: the lug under the rear ring's middle is in the slot three behind the front wheel's and three ahead of the rear wheel's (the four slots that show put hidden slots at columns 980, 1270.6 and 1561: the wheels and the lug)."}],"note":"Three slot pitches (30.02 mm): the rear ring stands over the recoil lug, which is in the slot midway between the two clamps' slots."},"ring_front_x":{"label":"Front ring, its middle ahead of the rear clamp's shaft","kind":"length","measurements":[{"id":"derived","value":114,"unit":"mm","pm":0.6,"source":{"type":"derived","expr":"{.ring_rear_x} + {.ring_gap} + {.ring_length}","via":"harvest"},"note":"The drawing's own 24 + 60 between the two rings' middles. Read directly on it: 113.96 mm (the front ring's faces at columns 343 and 594.5)."}]},"clamp_spacing":{"label":"Front clamp's shaft ahead of the rear clamp's","kind":"length","measurements":[{"id":"as-drawn","value":60,"unit":"mm","pm":0.15,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"the two wheels' centres, columns 1033.04 and 1660.54: 627.5 px. On the rail drawn under them the front wheel is on the centre of the sixth slot from the first drawn (1033.3) and the rear on the twelfth (1661.4)","via":"harvest"}},{"id":"slots","value":2.364,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"6 * {std.picatinny.slot_pitch}","via":"harvest"},"note":"What a shaft in a slot at each end comes to. The side photo: the wheels' middles at about columns 981 and 1566, six pitches of 96.81 px apart, on the hidden slots at 980 and 1561."}],"adopt":{"from":"slots","reason":"Both shafts lie in rail slots (the drawing draws the rail under them; the photo shows it): six pitches. The drawing's own 60.0 mm is within its reading's ± of that."},"note":"Six slot pitches (60.05 mm): each ClickDrive wheel turns on a shaft that crosses the rail in a slot. The front ring's whole length is ahead of the front clamp."},"lug_x":{"label":"Recoil lug, its middle ahead of the rear clamp's shaft","kind":"length","measurements":[{"id":"as-drawn","value":30,"unit":"mm","pm":0.15,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"the tab drawn under the base between the clamps, columns 1320.5 to 1373.3: its middle, 1346.9, to the rear wheel's centre","via":"harvest"},"note":"In the rail's slot midway between the two shafts' slots (the drawing draws it inside one; the side photo shows it in the slot between the two that show under the mount's middle)."}]},"lug_length":{"label":"Recoil lug, along the rail","kind":"length","measurements":[{"id":"as-drawn","value":5.05,"unit":"mm","pm":0.15,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"the tab's two faces, columns 1320.5 and 1373.3: 52.8 px. A slot is 5.23 mm (std.picatinny.slot_width)","via":"harvest"}}]},"lug_depth":{"label":"Recoil lug, below the rail's top","kind":"length","measurements":[{"id":"as-drawn","value":2.3,"unit":"mm","pm":0.15,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"the tab's lower edge (rows 1400 to 1401) under the rail's top line (1376.5)","via":"harvest"}}]},"lug_width":{"label":"Recoil lug, across the rail","kind":"length","measurements":[{"id":"underside","value":7,"unit":"mm","pm":2,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount 01bfe847a8c9 (Scalarworks, Scalarworks-LEAP-G3-Lightweight.jpg: the mount alone, oblique from below on the left side, 2000 x 1250; the page's picture of this generation, the height not said)","scaleRef":"the base's own width beside it (pedestal_width), as a proportion in an oblique: no camera was fitted","method":"the tab between \"MADE IN USA\" and \"CAGE\" is about 0.4 of the spine's width across","via":"harvest"},"note":"A proportion by eye. It is inside a rail slot when mounted."}]},"wheel_d":{"label":"ClickDrive wheel, over its knurl","kind":"length","measurements":[{"id":"as-drawn","value":16,"unit":"mm","pm":0.2,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"each wheel's lowest crest (row 1463) under its centre (row 1379.24): 83.8 px, twice","via":"harvest"}}],"note":"Twenty teeth: counted on the drawing where each wheel's rim is clear of everything else (its lower arc: crests 17.7 and 18.1 degrees apart on the front and the rear wheel)."},"wheel_root_d":{"label":"ClickDrive wheel, at the foot of its knurl","kind":"length","measurements":[{"id":"as-drawn","value":14.8,"unit":"mm","pm":0.3,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"the rim's distance from the centre between crests (77.25 and 77.75 px on the two wheels), twice","via":"harvest"}}]},"wheel_face_d":{"label":"ClickDrive wheel, the dished face inside its rim","kind":"length","measurements":[{"id":"as-drawn","value":13.15,"unit":"mm","pm":0.1,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"the full circle drawn at 68.75 px from each wheel's centre","via":"harvest"}}]},"wheel_axis_below_rail":{"label":"Clamp shaft's axis below the rail's top","kind":"length","measurements":[{"id":"as-drawn","value":0.26,"unit":"mm","pm":0.15,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"the wheels' centres (rows 1379.23 and 1379.25) under the rail's top line (1376.5)","via":"harvest"},"note":"The shaft is half in the slot and half in the base."}]},"shaft_d":{"label":"Clamp shaft","kind":"length","measurements":[{"id":"as-drawn","value":3.92,"unit":"mm","pm":0.1,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"the circle drawn at 20.5 px from each wheel's centre (its end in the wheel's face); a smaller one at 15.5 px inside it (2.96 mm: the socket in its end)","via":"harvest"}}]},"wheel_outer_z":{"label":"ClickDrive wheel, its outer face left of the mount's middle","kind":"length","measurements":[{"id":"rear-photo","value":17.3,"unit":"mm","pm":0.5,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount 110653a99256 (Scalarworks, scalarworks-leap-08-gen3-quick-detach-mount-1.57-rear-SW0815.jpg: SW0815 alone on a rail section, straight from behind, 2000 x 2000)","scaleRef":"the rear ring's 30 mm bore: the inner edge of its rear chamfer is 491.4 px across (16.38 px/mm at the ring's rear face), about the column 982.9 and the row 721.7. The far rim seen through the ring is 479.5 px and 1.25 px off that centre, so the lens is on the bore's axis about 38 in behind: what stands nearer is larger by 2.5% for each inch (the rear wheel, 18 mm behind that face by the drawing: 16.69 px/mm; the base's rear end, 34 mm behind it: 16.98)","method":"the wheel's outer face, column 694, from the bore's centre column: 288.9 px at the wheel's scale","via":"harvest"}}]},"wheel_thickness":{"label":"ClickDrive wheel, across","kind":"length","measurements":[{"id":"rear-photo","value":4.7,"unit":"mm","pm":0.6,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount 110653a99256 (Scalarworks, scalarworks-leap-08-gen3-quick-detach-mount-1.57-rear-SW0815.jpg: SW0815 alone on a rail section, straight from behind, 2000 x 2000)","scaleRef":"the rear ring's 30 mm bore: the inner edge of its rear chamfer is 491.4 px across (16.38 px/mm at the ring's rear face), about the column 982.9 and the row 721.7. The far rim seen through the ring is 479.5 px and 1.25 px off that centre, so the lens is on the bore's axis about 38 in behind: what stands nearer is larger by 2.5% for each inch (the rear wheel, 18 mm behind that face by the drawing: 16.69 px/mm; the base's rear end, 34 mm behind it: 16.98)","method":"the wheel's outer face (column 694) to where it meets the base's side above the rear block (column 771.5): 78 px at the wheel's scale. Its inner face is hidden","via":"harvest"}}]},"ring_top_above_axis":{"label":"Ring caps, their top flat above the axis","kind":"length","measurements":[{"id":"as-drawn","value":18.12,"unit":"mm","pm":0.1,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"the caps' top line (rows 764 to 765) above the centre line (954): 189.5 px","via":"harvest"}},{"id":"rear-photo","value":18.15,"unit":"mm","pm":0.25,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount 110653a99256 (Scalarworks, scalarworks-leap-08-gen3-quick-detach-mount-1.57-rear-SW0815.jpg: SW0815 alone on a rail section, straight from behind, 2000 x 2000)","scaleRef":"the rear ring's 30 mm bore: the inner edge of its rear chamfer is 491.4 px across (16.38 px/mm at the ring's rear face), about the column 982.9 and the row 721.7. The far rim seen through the ring is 479.5 px and 1.25 px off that centre, so the lens is on the bore's axis about 38 in behind: what stands nearer is larger by 2.5% for each inch (the rear wheel, 18 mm behind that face by the drawing: 16.69 px/mm; the base's rear end, 34 mm behind it: 16.98)","method":"the rear ring's top edge (row 424.4) above the bore's centre (721.7): 297.3 px at the ring's rear face","via":"harvest"},"note":"Two sources and two scales (the drawing's dimension lines, the photo's bore): 0.03 mm apart."}],"adopt":{"from":"as-drawn","reason":"The drawing's line, the finer reading; the photo from behind agrees."}},"ring_end_chamfer":{"label":"Rings, the chamfer between each end face and the side flats","kind":"length","measurements":[{"id":"as-drawn","value":1.05,"unit":"mm","pm":0.15,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"the line drawn up each ring 11 px inside each end face (columns 354 and 583.5 for the front ring's faces at 343 and 594.5; 1232 and 1461.5 for the rear's at 1221 and 1472.5)","via":"harvest"},"note":"The three-quarter picture (ccc3b2ef30ab) shows it as a lit band round each end face. Drawn on the upright edges (the end faces against the side flats and the chamfers), not round the top flat."}]},"ring_width":{"label":"Ring caps, across their side flats","kind":"length","measurements":[{"id":"rear-photo","value":44.3,"unit":"mm","pm":0.4,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount 110653a99256 (Scalarworks, scalarworks-leap-08-gen3-quick-detach-mount-1.57-rear-SW0815.jpg: SW0815 alone on a rail section, straight from behind, 2000 x 2000)","scaleRef":"the rear ring's 30 mm bore: the inner edge of its rear chamfer is 491.4 px across (16.38 px/mm at the ring's rear face), about the column 982.9 and the row 721.7. The far rim seen through the ring is 479.5 px and 1.25 px off that centre, so the lens is on the bore's axis about 38 in behind: what stands nearer is larger by 2.5% for each inch (the rear wheel, 18 mm behind that face by the drawing: 16.69 px/mm; the base's rear end, 34 mm behind it: 16.98)","method":"the cap's two sides just above the split, columns 621 and 1346 (rows 670 to 700): 725 px; 22.1 mm each side of the bore's centre","via":"harvest"}}]},"ring_lower_width":{"label":"Rings' lower halves, across their side flats","kind":"length","measurements":[{"id":"rear-photo","value":42.8,"unit":"mm","pm":0.4,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount 110653a99256 (Scalarworks, scalarworks-leap-08-gen3-quick-detach-mount-1.57-rear-SW0815.jpg: SW0815 alone on a rail section, straight from behind, 2000 x 2000)","scaleRef":"the rear ring's 30 mm bore: the inner edge of its rear chamfer is 491.4 px across (16.38 px/mm at the ring's rear face), about the column 982.9 and the row 721.7. The far rim seen through the ring is 479.5 px and 1.25 px off that centre, so the lens is on the bore's axis about 38 in behind: what stands nearer is larger by 2.5% for each inch (the rear wheel, 18 mm behind that face by the drawing: 16.69 px/mm; the base's rear end, 34 mm behind it: 16.98)","method":"the lower half's two sides just under the split, columns 630.1 and 1331.6 (rows 730 to 790): 701.5 px. The cap overhangs it by 0.7 mm a side","via":"harvest"}}]},"ring_top_flat_width":{"label":"Ring caps, their top flat across","kind":"length","measurements":[{"id":"rear-photo","value":20.3,"unit":"mm","pm":0.6,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount 110653a99256 (Scalarworks, scalarworks-leap-08-gen3-quick-detach-mount-1.57-rear-SW0815.jpg: SW0815 alone on a rail section, straight from behind, 2000 x 2000)","scaleRef":"the rear ring's 30 mm bore: the inner edge of its rear chamfer is 491.4 px across (16.38 px/mm at the ring's rear face), about the column 982.9 and the row 721.7. The far rim seen through the ring is 479.5 px and 1.25 px off that centre, so the lens is on the bore's axis about 38 in behind: what stands nearer is larger by 2.5% for each inch (the rear wheel, 18 mm behind that face by the drawing: 16.69 px/mm; the base's rear end, 34 mm behind it: 16.98)","method":"the cap is 343.5 px across at row 430, 5.6 rows under its top edge, on chamfers that go out a pixel for each row down (45 degrees: 781.3 to 1186.3 at row 460): 332 px at the top","via":"harvest"}}]},"ring_cap_shoulder_width":{"label":"Ring caps, across where their 45 degree chamfers end","kind":"length","measurements":[{"id":"rear-photo","value":42.4,"unit":"mm","pm":0.5,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount 110653a99256 (Scalarworks, scalarworks-leap-08-gen3-quick-detach-mount-1.57-rear-SW0815.jpg: SW0815 alone on a rail section, straight from behind, 2000 x 2000)","scaleRef":"the rear ring's 30 mm bore: the inner edge of its rear chamfer is 491.4 px across (16.38 px/mm at the ring's rear face), about the column 982.9 and the row 721.7. The far rim seen through the ring is 479.5 px and 1.25 px off that centre, so the lens is on the bore's axis about 38 in behind: what stands nearer is larger by 2.5% for each inch (the rear wheel, 18 mm behind that face by the drawing: 16.69 px/mm; the base's rear end, 34 mm behind it: 16.98)","method":"the chamfer's foot each side: columns 635.8 and 1333.1 at row 610 (6.8 mm above the axis); below it the side goes out another 0.9 mm to the side flat","via":"harvest"}}]},"ring_cap_side_flat":{"label":"Ring caps, their side flat's height above the split","kind":"length","measurements":[{"id":"as-drawn","value":3.1,"unit":"mm","pm":0.15,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"the line drawn along each cap at rows 921 to 922, above the split (954)","via":"harvest"},"note":"The photo from behind: the cap's side stops going out at row 670, 3.16 mm above the axis."}]},"ring_lower_side_flat":{"label":"Rings' lower halves, their side flat's height below the split","kind":"length","measurements":[{"id":"as-drawn","value":4.5,"unit":"mm","pm":0.15,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"the line drawn along each lower half at row 1001, under the split (954)","via":"harvest"},"note":"The photo from behind: the side turns in at about row 797, 4.6 mm under the axis."}]},"ring_lower_chamfer_drop":{"label":"Rings' lower halves, where the chamfer under the side flat meets the round, below the axis","kind":"length","measurements":[{"id":"rear-photo","value":7.8,"unit":"mm","pm":0.4,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount 110653a99256 (Scalarworks, scalarworks-leap-08-gen3-quick-detach-mount-1.57-rear-SW0815.jpg: SW0815 alone on a rail section, straight from behind, 2000 x 2000)","scaleRef":"the rear ring's 30 mm bore: the inner edge of its rear chamfer is 491.4 px across (16.38 px/mm at the ring's rear face), about the column 982.9 and the row 721.7. The far rim seen through the ring is 479.5 px and 1.25 px off that centre, so the lens is on the bore's axis about 38 in behind: what stands nearer is larger by 2.5% for each inch (the rear wheel, 18 mm behind that face by the drawing: 16.69 px/mm; the base's rear end, 34 mm behind it: 16.98)","method":"the outline leaves the side flat at row 797 and is on the round by row 850 (column 694.7: 17.6 mm out, 7.83 mm down)","via":"harvest"}}]},"ring_lower_r":{"label":"Rings' lower halves, the round under the tube: its radius about the axis","kind":"length","measurements":[{"id":"rear-photo","value":19.1,"unit":"mm","pm":0.3,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount 110653a99256 (Scalarworks, scalarworks-leap-08-gen3-quick-detach-mount-1.57-rear-SW0815.jpg: SW0815 alone on a rail section, straight from behind, 2000 x 2000)","scaleRef":"the rear ring's 30 mm bore: the inner edge of its rear chamfer is 491.4 px across (16.38 px/mm at the ring's rear face), about the column 982.9 and the row 721.7. The far rim seen through the ring is 479.5 px and 1.25 px off that centre, so the lens is on the bore's axis about 38 in behind: what stands nearer is larger by 2.5% for each inch (the rear wheel, 18 mm behind that face by the drawing: 16.69 px/mm; the base's rear end, 34 mm behind it: 16.98)","method":"six points of the outline between the chamfer and the pedestal (rows 850 to 1000, the left side): 19.26, 19.1, 19.1, 19.09, 19.07 and 19.47 mm from the bore's centre. A wall of 4.1 mm under the tube","via":"harvest"}}]},"pedestal_width":{"label":"Pedestals under the rings, across","kind":"length","measurements":[{"id":"rear-photo","value":17.6,"unit":"mm","pm":0.3,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount 110653a99256 (Scalarworks, scalarworks-leap-08-gen3-quick-detach-mount-1.57-rear-SW0815.jpg: SW0815 alone on a rail section, straight from behind, 2000 x 2000)","scaleRef":"the rear ring's 30 mm bore: the inner edge of its rear chamfer is 491.4 px across (16.38 px/mm at the ring's rear face), about the column 982.9 and the row 721.7. The far rim seen through the ring is 479.5 px and 1.25 px off that centre, so the lens is on the bore's axis about 38 in behind: what stands nearer is larger by 2.5% for each inch (the rear wheel, 18 mm behind that face by the drawing: 16.69 px/mm; the base's rear end, 34 mm behind it: 16.98)","method":"the rear pedestal's two sides, columns 837.8 and 1125.8 (rows 1040 to 1140): 288 px at the ring's rear face","via":"harvest"},"note":"The beam between the rings is taken to be as wide: the one picture of it from above (Scalarworks-Scope-Ring-Six-Screws.jpg, the beam running out of frame under a cap) has it 17.1 mm at the cap's scale, an inch nearer the lens than it."}]},"base_left_z":{"label":"Clamp blocks, their left face from the mount's middle","kind":"length","measurements":[{"id":"rear-photo","value":16.9,"unit":"mm","pm":0.5,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount 110653a99256 (Scalarworks, scalarworks-leap-08-gen3-quick-detach-mount-1.57-rear-SW0815.jpg: SW0815 alone on a rail section, straight from behind, 2000 x 2000)","scaleRef":"the rear ring's 30 mm bore: the inner edge of its rear chamfer is 491.4 px across (16.38 px/mm at the ring's rear face), about the column 982.9 and the row 721.7. The far rim seen through the ring is 479.5 px and 1.25 px off that centre, so the lens is on the bore's axis about 38 in behind: what stands nearer is larger by 2.5% for each inch (the rear wheel, 18 mm behind that face by the drawing: 16.69 px/mm; the base's rear end, 34 mm behind it: 16.98)","method":"the rear block's left face (column 695.7, rows 1360 to 1480) from the bore's centre column, at the base's rear end's scale: 287.2 px. The wheel's face is flush with it within the reading","via":"harvest"}}]},"base_right_z":{"label":"Clamp blocks, their right face from the mount's middle","kind":"length","measurements":[{"id":"rear-photo","value":16.6,"unit":"mm","pm":0.5,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount 110653a99256 (Scalarworks, scalarworks-leap-08-gen3-quick-detach-mount-1.57-rear-SW0815.jpg: SW0815 alone on a rail section, straight from behind, 2000 x 2000)","scaleRef":"the rear ring's 30 mm bore: the inner edge of its rear chamfer is 491.4 px across (16.38 px/mm at the ring's rear face), about the column 982.9 and the row 721.7. The far rim seen through the ring is 479.5 px and 1.25 px off that centre, so the lens is on the bore's axis about 38 in behind: what stands nearer is larger by 2.5% for each inch (the rear wheel, 18 mm behind that face by the drawing: 16.69 px/mm; the base's rear end, 34 mm behind it: 16.98)","method":"the rear block's right face (column 1264.4, rows 1380 to 1420) from the bore's centre column, at the base's rear end's scale: 281.5 px","via":"harvest"}}]},"clamp_top_above_rail":{"label":"Clamp blocks, their top above the rail's top","kind":"length","measurements":[{"id":"as-drawn","value":7.2,"unit":"mm","pm":0.1,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"the line along the top of each clamp's wall (row 1301) above the rail's top line (1376.5)","via":"harvest"}}]},"hook_below_rail":{"label":"Clamp blocks, their foot below the rail's top","kind":"length","measurements":[{"id":"as-drawn","value":5.8,"unit":"mm","pm":0.1,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"the walls' lower edge beside each wheel (row 1437) under the rail's top line (1376.5): 60.5 px. The wall ahead of the front wheel ends 1 mm higher (row 1427)","via":"harvest"}},{"id":"rear-photo","value":5.9,"unit":"mm","pm":0.4,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount 110653a99256 (Scalarworks, scalarworks-leap-08-gen3-quick-detach-mount-1.57-rear-SW0815.jpg: SW0815 alone on a rail section, straight from behind, 2000 x 2000)","scaleRef":"the rear ring's 30 mm bore: the inner edge of its rear chamfer is 491.4 px across (16.38 px/mm at the ring's rear face), about the column 982.9 and the row 721.7. The far rim seen through the ring is 479.5 px and 1.25 px off that centre, so the lens is on the bore's axis about 38 in behind: what stands nearer is larger by 2.5% for each inch (the rear wheel, 18 mm behind that face by the drawing: 16.69 px/mm; the base's rear end, 34 mm behind it: 16.98)","method":"the two hooks' lower edges (row 1494) under the base's underside over the rail (row 1393.6), at the base's rear end's scale","via":"harvest"}}],"adopt":{"from":"as-drawn","reason":"The drawing's line; the photo from behind agrees."}},"front_block_rear_x":{"label":"Front clamp block, its rear end ahead of the rear clamp's shaft","kind":"length","measurements":[{"id":"as-drawn","value":44,"unit":"mm","pm":0.2,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"the block's rear end at its foot, column 1201, from the frame's x = 0 (column 1660.75)","via":"harvest"},"note":"Behind it the base is as narrow as the pedestal (the oblique from below), as far as the rear block."}]},"front_block_toe_x":{"label":"Front clamp block, its toe at the foot ahead of the rear clamp's shaft","kind":"length","measurements":[{"id":"as-drawn","value":71.7,"unit":"mm","pm":0.3,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"the front face's lower end, column 911 at the foot (rows 1420 to 1436: 907 to 914)","via":"harvest"}}]},"front_block_top_x":{"label":"Front clamp block, its front face at the block's top ahead of the rear clamp's shaft","kind":"length","measurements":[{"id":"as-drawn","value":75.5,"unit":"mm","pm":0.4,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"the front face leans forward going up, in line with the cantilever's underside: it crosses the block's top line (row 1301) at column 871","via":"harvest"}}]},"rear_block_front_x":{"label":"Rear clamp block, its front end ahead of the rear clamp's shaft","kind":"length","measurements":[{"id":"as-drawn","value":15.8,"unit":"mm","pm":0.2,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"the block's front end at its foot, column 1495.5","via":"harvest"}}]},"rear_block_rear_x":{"label":"Rear clamp block, its rear face at the foot behind the rear clamp's shaft","kind":"length","measurements":[{"id":"as-drawn","value":13.9,"unit":"mm","pm":0.2,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"the rear face at the foot, column 1806; above the foot the base's end face stands 2 mm further back (column 1827.5), under the rear deck","via":"harvest"}}]},"block_side_top":{"label":"Clamp blocks, where their upright side faces end above the rail's top","kind":"length","measurements":[{"id":"rear-photo","value":1.9,"unit":"mm","pm":0.4,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount 110653a99256 (Scalarworks, scalarworks-leap-08-gen3-quick-detach-mount-1.57-rear-SW0815.jpg: SW0815 alone on a rail section, straight from behind, 2000 x 2000)","scaleRef":"the rear ring's 30 mm bore: the inner edge of its rear chamfer is 491.4 px across (16.38 px/mm at the ring's rear face), about the column 982.9 and the row 721.7. The far rim seen through the ring is 479.5 px and 1.25 px off that centre, so the lens is on the bore's axis about 38 in behind: what stands nearer is larger by 2.5% for each inch (the rear wheel, 18 mm behind that face by the drawing: 16.69 px/mm; the base's rear end, 34 mm behind it: 16.98)","method":"the rear block's left face is upright up to row 1362, over the base's underside on the rail (row 1393.6), at the base's rear end's scale; above it a chamfer goes in","via":"harvest"}}]},"block_shoulder_z":{"label":"Clamp blocks, the top of their side chamfer from the mount's middle","kind":"length","measurements":[{"id":"rear-photo","value":15.2,"unit":"mm","pm":0.5,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount 110653a99256 (Scalarworks, scalarworks-leap-08-gen3-quick-detach-mount-1.57-rear-SW0815.jpg: SW0815 alone on a rail section, straight from behind, 2000 x 2000)","scaleRef":"the rear ring's 30 mm bore: the inner edge of its rear chamfer is 491.4 px across (16.38 px/mm at the ring's rear face), about the column 982.9 and the row 721.7. The far rim seen through the ring is 479.5 px and 1.25 px off that centre, so the lens is on the bore's axis about 38 in behind: what stands nearer is larger by 2.5% for each inch (the rear wheel, 18 mm behind that face by the drawing: 16.69 px/mm; the base's rear end, 34 mm behind it: 16.98)","method":"the chamfer's upper end on the left, column 724.5","via":"harvest"}}]},"block_shoulder_y":{"label":"Clamp blocks, the top of their side chamfer above the rail's top","kind":"length","measurements":[{"id":"rear-photo","value":4.3,"unit":"mm","pm":0.4,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount 110653a99256 (Scalarworks, scalarworks-leap-08-gen3-quick-detach-mount-1.57-rear-SW0815.jpg: SW0815 alone on a rail section, straight from behind, 2000 x 2000)","scaleRef":"the rear ring's 30 mm bore: the inner edge of its rear chamfer is 491.4 px across (16.38 px/mm at the ring's rear face), about the column 982.9 and the row 721.7. The far rim seen through the ring is 479.5 px and 1.25 px off that centre, so the lens is on the bore's axis about 38 in behind: what stands nearer is larger by 2.5% for each inch (the rear wheel, 18 mm behind that face by the drawing: 16.69 px/mm; the base's rear end, 34 mm behind it: 16.98)","method":"the chamfer's upper end on the left, row 1321, over the base's underside on the rail (row 1393.6); from there the top rises to the pedestal","via":"harvest"}}]},"wheel_pocket_gap":{"label":"Round pocket for each wheel in the left wall: its clearance round the wheel","kind":"length","measurements":[{"id":"assumed","value":0.3,"unit":"mm","pm":0.2,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the drawing and the side photo have the wall's hollowed ends close round each wheel, with a line of shadow between.","via":"harvest"}}]},"jaw_end_inset":{"label":"Right-hand jaws, short of their block's two ends","kind":"length","measurements":[{"id":"assumed","value":2,"unit":"mm","pm":1.5,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: from behind (110653a99256) the rear block's own end shows a hook on the right as on the left, in the base's matte black, so the steel jaw the oblique from below shows under that block stops short of its end; by how much isn't read.","via":"harvest"}}]},"cap_pocket_floor":{"label":"Ring caps' screw pockets, their floor above the axis","kind":"length","measurements":[{"id":"as-drawn","value":5.45,"unit":"mm","pm":0.3,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"the two lines along the foot of each cap's side recess (rows 894.5 and 899.5): between them","via":"harvest"}}]},"cap_pocket_length":{"label":"Ring caps' screw pockets, along the tube","kind":"length","measurements":[{"id":"as-drawn","value":19.75,"unit":"mm","pm":0.2,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"each recess's two end walls, columns 365.5 and 572 on the front ring: 206.5 px, about the ring's middle","via":"harvest"}}]},"cap_pocket_inner_z":{"label":"Ring caps' screw pockets, their inner wall from the mount's middle","kind":"length","measurements":[{"id":"top-photo","value":16,"unit":"mm","pm":0.5,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount 652257eb3c65 (Scalarworks, Scalarworks-Scope-Ring-Six-Screws.jpg: one ring cap straight from above, 2000 x 2000; on the LEAP/08 page, which mount it is on isn't said)","scaleRef":"the cap's own two sizes in the picture: 24 mm along the tube (ring_length) and 44.3 mm across (ring_width): 35.4 and 35.2 px/mm on the picture shown 1932 px wide, read on its grid to about ± 0.3 mm","method":"each dark pocket's inner edge, 565 px from the cap's middle","via":"harvest"},"note":"The drawing has the pocket's inner wall meeting the cap's chamfer 11.95 mm above the axis (row 829), which a 45 degree chamfer from a top flat 20.3 mm wide does at 16.3 mm out."}]},"cap_screw_z":{"label":"Ring cap screws, from the mount's middle","kind":"length","measurements":[{"id":"top-photo","value":18.75,"unit":"mm","pm":0.4,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount 652257eb3c65 (Scalarworks, Scalarworks-Scope-Ring-Six-Screws.jpg: one ring cap straight from above, 2000 x 2000; on the LEAP/08 page, which mount it is on isn't said)","scaleRef":"the cap's own two sizes in the picture: 24 mm along the tube (ring_length) and 44.3 mm across (ring_width): 35.4 and 35.2 px/mm on the picture shown 1932 px wide, read on its grid to about ± 0.3 mm","method":"the two rows of three screw heads, 1324 px apart","via":"harvest"}}]},"cap_screw_pitch":{"label":"Ring cap screws, apart along the tube","kind":"length","measurements":[{"id":"top-photo","value":7.1,"unit":"mm","pm":0.25,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount 652257eb3c65 (Scalarworks, Scalarworks-Scope-Ring-Six-Screws.jpg: one ring cap straight from above, 2000 x 2000; on the LEAP/08 page, which mount it is on isn't said)","scaleRef":"the cap's own two sizes in the picture: 24 mm along the tube (ring_length) and 44.3 mm across (ring_width): 35.4 and 35.2 px/mm on the picture shown 1932 px wide, read on its grid to about ± 0.3 mm","method":"three heads' centres down each side, 251 px apart; the middle one on the ring's middle","via":"harvest"},"note":"The drawing draws the three heads in each cap's recess 7.0 mm apart."}],"note":"Three a side, six to a ring, twelve in all: the page's \"Fasteners (12) #8-40 Nylon patched\"; the manual: T15, \"until torque stabilizes at 20inch-lbs\"."},"cap_screw_head_d":{"label":"Ring cap screws, their heads","kind":"length","measurements":[{"id":"top-photo","value":5.2,"unit":"mm","pm":0.3,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount 652257eb3c65 (Scalarworks, Scalarworks-Scope-Ring-Six-Screws.jpg: one ring cap straight from above, 2000 x 2000; on the LEAP/08 page, which mount it is on isn't said)","scaleRef":"the cap's own two sizes in the picture: 24 mm along the tube (ring_length) and 44.3 mm across (ring_width): 35.4 and 35.2 px/mm on the picture shown 1932 px wide, read on its grid to about ± 0.3 mm","method":"a head's rim, about 185 px across","via":"harvest"}}]},"cap_screw_head_h":{"label":"Ring cap screws, their heads above the pocket's floor","kind":"length","measurements":[{"id":"as-drawn","value":0.75,"unit":"mm","pm":0.3,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"the heads' tops (row 889) above the recess's foot (rows 894.5 to 899.5)","via":"harvest"}}]},"cap_hole_d":{"label":"Ring caps, the two holes in the top flat","kind":"length","measurements":[{"id":"top-photo","value":5.5,"unit":"mm","pm":0.3,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount 652257eb3c65 (Scalarworks, Scalarworks-Scope-Ring-Six-Screws.jpg: one ring cap straight from above, 2000 x 2000; on the LEAP/08 page, which mount it is on isn't said)","scaleRef":"the cap's own two sizes in the picture: 24 mm along the tube (ring_length) and 44.3 mm across (ring_width): 35.4 and 35.2 px/mm on the picture shown 1932 px wide, read on its grid to about ± 0.3 mm","method":"each hole, 193 px across; the bore's grooves show through both","via":"harvest"}}],"note":"For Scalarworks' KICK mounts (the page: \"KICK Extension Mounts\"); nothing on the page says what the holes are."},"cap_hole_spacing":{"label":"Ring caps, the two holes apart along the tube","kind":"length","measurements":[{"id":"top-photo","value":12.3,"unit":"mm","pm":0.3,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount 652257eb3c65 (Scalarworks, Scalarworks-Scope-Ring-Six-Screws.jpg: one ring cap straight from above, 2000 x 2000; on the LEAP/08 page, which mount it is on isn't said)","scaleRef":"the cap's own two sizes in the picture: 24 mm along the tube (ring_length) and 44.3 mm across (ring_width): 35.4 and 35.2 px/mm on the picture shown 1932 px wide, read on its grid to about ± 0.3 mm","method":"their centres, 435 px apart, either side of the ring's middle on the mount's middle line","via":"harvest"}}]},"pedestal_hole_d":{"label":"Pedestals, the two holes across each","kind":"length","measurements":[{"id":"as-drawn","value":3.73,"unit":"mm","pm":0.1,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"the inner circle of each, 19.5 px from its centre; round it a counterbore at 36.5 px (6.98 mm)","via":"harvest"}}],"note":"Engraved \"15 in-lbs\" between them (the side photo); they show the white ground through in it: through holes."},"pedestal_hole_spacing":{"label":"Pedestals, the two holes apart along the tube","kind":"length","measurements":[{"id":"as-drawn","value":11.74,"unit":"mm","pm":0.1,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"their centres, columns 407.1 and 529.9 under the front ring (1285.0 and 1407.9 under the rear): 122.8 px, either side of the ring's middle","via":"harvest"}}]},"pedestal_hole_below_axis":{"label":"Pedestals, the two holes below the axis","kind":"length","measurements":[{"id":"as-drawn","value":21.9,"unit":"mm","pm":0.1,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"their centres' row, 1183, under the centre line (954)","via":"harvest"}}]},"pedestal_recess_h":{"label":"Pedestals, the recess the two holes are in: its height","kind":"length","measurements":[{"id":"as-drawn","value":7.7,"unit":"mm","pm":0.15,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"its two long edges, rows 1142.5 and 1223: round-ended, 19.4 mm long (columns 367 to 570), centred on the holes' row","via":"harvest"}}]},"pedestal_recess_depth":{"label":"Pedestals, the recess's depth into each side","kind":"length","measurements":[{"id":"three-quarter","value":6,"unit":"mm","pm":2,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount ccc3b2ef30ab (Scalarworks, scalarworks-leap-08-gen3-quick-detach-mount-1.57-hero-SW0815.jpg: SW0815 on a rail section from the rear left, 2000 x 2000)","scaleRef":"the recess's own length (pedestal_recess_length) and the angle the picture is taken from: the rear ring's bore shows 0.75 as wide as it is tall, so the lens is 41 degrees off the tube's axis and 49 off square to the pedestal's side","method":"the recess's near wall hides about four tenths of its floor (the nearer of its two holes, and half the \"15 in-lbs\" between them, don't show): 7.8 mm, over the tangent of 49 degrees. No camera was fitted","via":"harvest"},"note":"It leaves a web 5.6 mm thick down the pedestal's middle, which the two holes go through."}],"note":"A deep pocket, not a line: the oblique from below (01bfe847a8c9) looks into the front one past its far wall."},"side_pocket_rear_x":{"label":"Pocket in the base's side under the rear ring: its rear end ahead of the rear clamp's shaft","kind":"length","measurements":[{"id":"as-drawn","value":17.3,"unit":"mm","pm":0.2,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"the panel's rear wall, column 1480","via":"harvest"}}],"note":"The panel between the two wheels in the side views: a recess in the base's side from the rail's top up, round-cornered at the top, between the two clamp blocks. The three-quarter picture (ccc3b2ef30ab) looks into it: a lit floor well inside a shadowed ceiling, and the rail's slots showing under it."},"side_pocket_front_x":{"label":"Pocket in the base's side under the rear ring: its front end ahead of the rear clamp's shaft","kind":"length","measurements":[{"id":"as-drawn","value":42.7,"unit":"mm","pm":0.2,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"the panel's front wall, column 1214","via":"harvest"}}]},"side_pocket_top":{"label":"Pocket in the base's side under the rear ring: its top above the rail's top","kind":"length","measurements":[{"id":"as-drawn","value":11.76,"unit":"mm","pm":0.15,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"the panel's top line (rows 1253 to 1254) above the rail's top line (1376.5); its two upper corners are round, about 2.6 mm (the lines at rows 1261.5 and 1280.5)","via":"harvest"}}]},"side_pocket_corner_r":{"label":"Pocket in the base's side under the rear ring: its upper corners' radius","kind":"length","measurements":[{"id":"as-drawn","value":2.6,"unit":"mm","pm":0.4,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"the line where each round corner ends, row 1280.5, under the top line (1253.5)","via":"harvest"}}]},"side_pocket_depth":{"label":"Pocket in the base's side under the rear ring: its depth into each side","kind":"length","measurements":[{"id":"assumed","value":5,"unit":"mm","pm":2,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the three-quarter picture (ccc3b2ef30ab) shows it deep, its floor in light well inside its ceiling's shadow, and no view shows it in profile. Taken a little shallower than the pedestals' recesses, to leave a web.","via":"harvest"}}]},"rib_pitch":{"label":"Rings' lower halves, the grooves down each side: their pitch","kind":"length","measurements":[{"id":"as-drawn","value":0.818,"unit":"mm","pm":0.02,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"ten lines from row 1021 to row 1098: 8.556 px apart","via":"harvest"}}],"note":"Ten lines on each side of each ring's lower half, between 6.4 and 13.8 mm under the axis, 18.9 mm long (columns 370 to 568): the ribbed panel of the side photo."},"rib_top_below_axis":{"label":"Rings' lower halves, the first groove below the axis","kind":"length","measurements":[{"id":"as-drawn","value":6.4,"unit":"mm","pm":0.1,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"the first of the ten lines, row 1021, under the centre line (954)","via":"harvest"}}]},"rib_depth":{"label":"Rings' lower halves, the grooves' depth","kind":"length","measurements":[{"id":"assumed","value":0.3,"unit":"mm","pm":0.2,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the grooves show as lines in the side views and as a faint sawtooth in the oblique from below.","via":"harvest"}}]},"rib_length":{"label":"Rings' lower halves, the grooves' length along the tube","kind":"length","measurements":[{"id":"as-drawn","value":18.9,"unit":"mm","pm":0.3,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"the ten lines' ends, columns 370 and 568 on the front ring: 198 px, about the ring's middle","via":"harvest"}}]},"pedestal_recess_length":{"label":"Pedestals, the recess the two holes are in: its length","kind":"length","measurements":[{"id":"as-drawn","value":19.4,"unit":"mm","pm":0.2,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"its two round ends, columns 367 and 570 on the front pedestal: 203 px, about the ring's middle","via":"harvest"}}]},"wheel_dish_depth":{"label":"ClickDrive wheel, how far its face is dished inside the rim","kind":"length","measurements":[{"id":"assumed","value":0.4,"unit":"mm","pm":0.3,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the drawing has the face as two circles, and the side photo a rim lit against a darker face with the name round it; no view shows it in profile.","via":"harvest"}}]},"split_groove_width":{"label":"Rings, the line between a cap and its lower half: the groove's width as drawn","kind":"length","measurements":[{"id":"assumed","value":0.008,"unit":"in","pm":0.004,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the split is a dark line in the side photo and a closed joint (\"NO GAP\") on the left; it is drawn as a fine groove round the ring so that the two halves read as two.","via":"harvest"}}]},"split_groove_depth":{"label":"Rings, the line between a cap and its lower half: the groove's depth as drawn","kind":"length","measurements":[{"id":"assumed","value":0.012,"unit":"in","pm":0.006,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows the joint in profile.","via":"harvest"}}]},"edge_break":{"label":"The aluminium's edges: the break drawn on them","kind":"length","measurements":[{"id":"assumed","value":0.005,"unit":"in","pm":0.003,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the photos show every machined edge with a small break and none in profile; the drawing draws the rings' end faces with a chamfer of about 1 mm, which isn't drawn as that.","via":"harvest"}}]},"flute_top_below_axis":{"label":"Cantilever, the stepped flutes along its lower sides: the first step's edge below the axis","kind":"length","measurements":[{"id":"as-drawn","value":30.26,"unit":"mm","pm":0.1,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"the first of three horizontal lines along the cantilever, row 1270.5 at every column from 432 to 820, under the centre line (954): 316.5 px","via":"harvest"}}],"note":"Three steps run along the lower part of each side of the cantilever, from the front clamp block's front face forward to under the front ring, where each ends in a point (the drawing's three horizontal lines, each with a line sloping down from its front end to the next: a step running out parallel to the arm's underside). The oblique from below (01bfe847a8c9) shows them on the left side as three lit edges converging to points under the front pedestal, and the three-quarter picture (ccc3b2ef30ab) as three lines along the arm. The right side isn't seen in any view: drawn the same, mirrored."},"flute_pitch":{"label":"Cantilever, the stepped flutes: one step's height","kind":"length","measurements":[{"id":"as-drawn","value":0.79,"unit":"mm","pm":0.05,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"the three lines at rows 1270.5, 1279 and 1287 (columns 500 to 820, each to half a pixel): 8.25 px apart","via":"harvest"}}]},"flute_front_x":{"label":"Cantilever, the stepped flutes: where each step begins at the front, ahead of the rear clamp's shaft","kind":"length","measurements":[{"id":"as-drawn","value":117.7,"unit":"mm","pm":0.3,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"the three lines' front ends, columns 428 to 432 (none at 425), from the rear wheel's centre (column 1660.54): 1230.5 px","via":"harvest"}}]},"flute_rear_x":{"label":"Cantilever, the stepped flutes: where they end at the front clamp block, ahead of the rear clamp's shaft","kind":"length","measurements":[{"id":"as-drawn","value":80,"unit":"mm","pm":0.4,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"the three lines run level to column 824 and then turn down the block's front face (at column 840 they are at rows 1275.5, 1286.5 and 1298): 836.5 px from the rear wheel's centre","via":"harvest"},"note":"Where they turn down the block's face isn't drawn: the steps end square at the block."}]},"flute_runout":{"label":"Cantilever, the stepped flutes: how far back a step's pointed front end runs before it is a step's full height","kind":"length","measurements":[{"id":"as-drawn","value":5.7,"unit":"mm","pm":0.4,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"each sloping line leaves a level line at column 430 and meets the next level line down at column 490 (rows 1270.5 to 1278.5, 1279 to 1286.5): 60 px, a slope of 0.133 that the arm's underside also has (0.123)","via":"harvest"}}]},"flute_step_depth":{"label":"Cantilever, the stepped flutes: how far each step is set into the side","kind":"length","measurements":[{"id":"assumed","value":0.4,"unit":"mm","pm":0.3,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows the arm in section. In the oblique from below the three edges are lit lines a few pixels apart, which a step of a few tenths of a millimetre makes; each step is drawn this much further in than the one above it.","via":"harvest"}}]},"under_pocket_front_x":{"label":"Pocket up into the cantilever's underside under the front ring: its front end, ahead of the rear clamp's shaft","kind":"length","measurements":[{"id":"underside","value":113.3,"unit":"mm","pm":3,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount 01bfe847a8c9 (Scalarworks, Scalarworks-LEAP-G3-Lightweight.jpg: the mount alone, oblique from below on the left side, 2000 x 1250; the page's picture of this generation, the height not said)","scaleRef":"the underside's own length along the arm, from where the nose's slope meets it (the drawing's column 377, 122.7 mm) to the front clamp block's front face (column 830, 79.4 mm): 409 px along the arm's direction in the picture","method":"the pocket's front end 89 px behind the nose's corner, along the arm (pixels projected on the arm's direction, 0.806 and 0.593): 9.4 mm behind it","via":"harvest"}}],"note":"The round-ended pocket the oblique from below (01bfe847a8c9) shows in the arm's underside, under the front ring and the arm behind it, its length along the arm (its own pixels about 590 to 745 across, 505 to 610 down). The only view of it: no camera was fitted, so where it lies and how long it is are proportions along the underside, whose two ends the drawing places."},"under_pocket_rear_x":{"label":"Pocket up into the cantilever's underside: its rear end, ahead of the rear clamp's shaft","kind":"length","measurements":[{"id":"underside","value":95.4,"unit":"mm","pm":3,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount 01bfe847a8c9 (Scalarworks, Scalarworks-LEAP-G3-Lightweight.jpg: the mount alone, oblique from below on the left side, 2000 x 1250; the page's picture of this generation, the height not said)","scaleRef":"the underside's own length along the arm, as under_pocket_front_x","method":"the pocket's rear end 258 px behind the nose's corner along the arm: 27.3 mm behind it. Its length, 17.8 mm, against the pedestal's side recess beside it (19.4 mm, pedestal_recess_length), seen along the same direction 150 px long: 21.2 mm, which the ± takes in","via":"harvest"}}]},"under_pocket_width":{"label":"Pocket up into the cantilever's underside: its width across","kind":"length","measurements":[{"id":"assumed","value":9,"unit":"mm","pm":3,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: in the oblique it takes about half the underside's width between the arm's two lower edges, which is all a picture taken along the arm from below says without a camera fitted to it.","via":"harvest"}}]},"under_pocket_depth":{"label":"Pocket up into the cantilever's underside: its depth","kind":"length","measurements":[{"id":"assumed","value":5,"unit":"mm","pm":3,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: its walls show dark and deep in the oblique; drawn this deep it stays under the pedestal's side recesses (their lower edge 8.6 mm over the underside there) and under the beam's top behind the ring.","via":"harvest"}}]},"mount_length":{"label":"Clamp length along the rail (at its foot)","kind":"length","measurements":[{"id":"as-drawn","value":85.6,"unit":"mm","pm":0.4,"source":{"type":"photo","photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815: the left side on a rail, 2000 x 2000)","scaleRef":"the drawing's own dimension lines along the tube: its extension lines at columns 343, 594, 1221.5 and 1472.5 are 24, 60 and 24 mm apart at 10.458 px/mm each (265.64 px/in); checked on the two 30 mm bore lines (313.5 px: 29.98 mm) and on the rail drawn under the mount (slot centres 104.68 px apart over fourteen pitches: 10.009 mm for the standard's 10.008)","method":"the front clamp block's toe at its foot (column 911) to the rear block's rear face at its foot (column 1806): 895 px. The two blocks are 28 and 30 mm long (to columns 1199 and from 1494), with the narrow base between them; the rear one is 13.9 mm behind the rear shaft","via":"harvest"}}]},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"page","value":161,"unit":"g","stated":"Weight SW0815 : 161g (5.68oz) SW0825 : 178g (6.28oz)","source":{"type":"spec","publisher":"manufacturer","name":"Scalarworks, LEAP/08 (product page, SPECIFICATIONS)","url":"https://scalarworks.com/shop/quick-detach-mounts/leap-08/","retrieved":"2026-10-13","via":"harvest"}}],"note":"THE MODEL HAS MORE METAL THAN THIS: its aluminium's volume as 7075 and its steel's as steel come to about a quarter more than 161 g (the manifest's metal_oz; the test holds the figure). The outline is the maker's drawing and the widths are its photo's; what the model lacks is the lightening the oblique from below shows and no view on file measures: pockets up into both clamp blocks' roofs beside each shaft, the LevelDrive's threaded hole, and whatever the right side has. (Since 2026-10-19 the cantilever's stepped flutes and the pocket up into its underside under the front ring are drawn, at assumed depths: 0.06 cubic inches, 7.13 oz became 7.04.) The model's volume is not this mount's weight and is not used as one. The page says the weight twice: \"Scalarworks ® SW0815 (161grams)\", beside three other makers' mounts. Its materials: \"7075-T6 Al / 4140 CrMo / 17-4 Stainless\", finishes \"Type III Anodizing / BlackNitride ®\". The model's metal is the check of its shape (app/tests/scalarworks-leap-08-30mm-mount.test.ts)."}}},{"subject":"sig-alpha-msr-30mm","title":"SIG SAUER ALPHA-MSR scope mount, 30 mm","dimensions":{"ring_bore":{"label":"Tube diameter the rings are bored for","kind":"length","measurements":[{"id":"engraving","value":30,"unit":"mm","stated":"P/N: SOA20014 30mm X 1.535\"","source":{"type":"spec","publisher":"manufacturer","name":"SIG SAUER, the engraving on the ALPHA-MSR mount's left side, as it reads in German Sport Guns' left-side product photo (references/sig-tango-msr-1-6x24 a140bd671551) and in the user's photos of the mount","url":"https://www.german-sport-guns.com/media/66/7d/53/1770809536/SOT61000_2.jpg","retrieved":"2026-10-01","via":"harvest"}},{"id":"gritr","value":30,"unit":"mm","stated":"Maintube Diameter, mm 30","source":{"type":"spec","publisher":"retailer","name":"Gritr Outdoors, ALPHA-MSR 30 mm mount SOA20014 (specifications)","url":"https://gritroutdoors.com/sig-sauer-alpha-msr-30mm-black-scope-mount-soa20014","retrieved":"2026-10-01","via":"harvest"},"note":"Read 2026-10-05 on the harvested copy. The same page: \"30mm Tube Diameter – Perfect size to securely hold most 30mm diameter optic tubes\"."},{"id":"ar15discounts","value":30,"unit":"mm","stated":"The ring diameter allows for scopes with 30mm diameters to have a secure fit","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, ALPHA-MSR 30 mm mount SOA20014 (description)","url":"https://ar15discounts.com/products/sig-sauer-alpha-msr-scope-mount-30mm-1-535-0-moa-6061-t6-black/","retrieved":"2026-10-01","via":"harvest"},"note":"Read 2026-10-05 on the harvested copy. Third Coast Thermal, of the two sizes it is sold in: \"Designed for scopes with 30mm or 34mm main tubes\"."}],"adopt":{"from":"engraving","reason":"SIG's own engraving on the mount; two sellers say the same of SOA20014."}},"optical_axis_above_rail":{"label":"Optical axis above the rail's top","kind":"length","measurements":[{"id":"mount","value":1.535,"unit":"in","stated":"P/N: SOA20014 30mm X 1.535\"","source":{"type":"spec","publisher":"manufacturer","name":"SIG SAUER, the engraving on the ALPHA-MSR mount's left side, as it reads in German Sport Guns' left-side product photo (references/sig-tango-msr-1-6x24 a140bd671551) and in the user's photos of the mount","url":"https://www.german-sport-guns.com/media/66/7d/53/1770809536/SOT61000_2.jpg","retrieved":"2026-10-01","via":"harvest"}},{"id":"gritr","value":1.535,"unit":"in","stated":"Height: 1.535” (measured from Picatinny rail to center of scope tube)","source":{"type":"spec","publisher":"retailer","name":"Gritr Outdoors, ALPHA-MSR 30 mm mount SOA20014","url":"https://gritroutdoors.com/sig-sauer-alpha-msr-30mm-black-scope-mount-soa20014","retrieved":"2026-10-01","via":"harvest"}},{"id":"third-coast","value":1.535,"unit":"in","stated":"Extra High mount height - 1.535 inch (centerline of optic to top of Pic rail)","source":{"type":"spec","publisher":"retailer","name":"Third Coast Thermal, ALPHA-MSR scope mount","url":"https://www.thirdcoastthermal.com/collections/rings-and-mounts/products/alpha-msr-scope-mount","retrieved":"2026-10-01","via":"harvest"}}],"adopt":{"from":"mount","reason":"SIG's own engraving on the mount; two retailers say what it is measured between."}},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"user","value":5.5,"unit":"oz","stated":"i think the mount weight is 5.5 oz","source":{"type":"spec","publisher":"unknown","name":"The user, in chat 2026-10-01, with two photos of the mount alone (where the figure is from wasn't said)","via":"user"}},{"id":"ar15discounts","value":6,"unit":"oz","stated":"Weight 6 oz","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, ALPHA-MSR 30 mm mount SOA20014 (Additional information)","url":"https://ar15discounts.com/products/sig-sauer-alpha-msr-scope-mount-30mm-1-535-0-moa-6061-t6-black/","retrieved":"2026-10-01","via":"harvest"},"note":"A whole number: 5.5 rounds to it."}],"adopt":{"from":"user","reason":"The finer figure; the retailer's whole number agrees with it."},"note":"SIG's figure wasn't reachable. The user's 5.5 oz matches what a search result shows for OpticsPlanet's listing (\"5.5 ounces\"), whose page is bot-checked and wasn't read."},"ring_od":{"label":"Mount rings, across their top and bottom flats","kind":"length","measurements":[{"id":"right","value":1.363,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a0aec57f834a (German Sport Guns SOT61000.jpg, right side: the turned body)","scaleRef":"scale from sig-tango-msr-1-6x24.tube_od = 1.1811 in, the tube's own width column by column: 276.1 px over columns 1170–1350, 275.5 px over columns 1545–1640, 274.6 px over columns 2025–2060, 273.0 px over columns 2290–2660; a line through them (rms 0.28 px) changes -1.5% from column 1170 to 2660, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1500)/width, the lens's axis taken to meet the image at column 1500; 233.4 px/in there. The axis is the tube's centre line (tilt -0.23°, rms 0.19 px). Lengths then scaled by 1.0125 so that the end faces are sig-tango-msr-1-6x24.length = 10.4 in apart: at the tube's scale they read 10.272 (-1.2%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.160 in over radius 0.591 (rms 0.002), the rear end's rim sags 0.055 in over radius 0.913 (rms 0.005)","method":"height (tooth tops, max over 0.05 in windows) along x [1.25, 1.75] of the traced outline (tools/trace.py); the rear ring's top flat to its mirror below the axis, 1.25 to 1.75 in ahead of the rear bolt","via":"harvest"}}],"note":"The rings are octagonal outside. Seen from the side their top flat is this far above the axis, twice over. Taken as the same across their side flats, and as the width of the mount's base, which no photo on file shows square-on."},"ring_rear_x":{"label":"Mount's rear ring, its middle ahead of the rear cross bolt","kind":"length","measurements":[{"id":"right","value":1.477,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a0aec57f834a (German Sport Guns SOT61000.jpg, right side: the turned body)","scaleRef":"the traced body outline's own: the 30 mm tube column by column, lengths to the published 10.4 in (profiles.body)","method":"the stretch of the traced outline at the rings' top flat (within 0.015 in of ring_od / 2), 1.152 to 1.802 in: its middle. A ring away from the lens's axis shows its near and far faces apart, so the stretch reads long (0.650 here and 0.707 at the front ring, where the mount's own side view has both top flats 0.62): its middle is what the two faces share","via":"harvest"}}],"note":"Where the mount's own side views are seated on the scope (tools/trace.py, a frame through the two rings' middles on the optical axis)."},"ring_front_x":{"label":"Mount's front ring, its middle ahead of the rear cross bolt","kind":"length","measurements":[{"id":"right","value":4.645,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a0aec57f834a (German Sport Guns SOT61000.jpg, right side: the turned body)","scaleRef":"the traced body outline's own: the 30 mm tube column by column, lengths to the published 10.4 in (profiles.body)","method":"the stretch of the traced outline at the rings' top flat, 4.292 to 4.999 in: its middle (as ring_rear_x)","via":"harvest"}}]},"ring_width":{"label":"Mount rings, across their side flats","kind":"length","measurements":[{"id":"obliques","value":1.686,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 f4997c570421 (German Sport Guns SOA20014.jpg, the mount alone from the front left and above, 3000 x 2000), eab80540c7f1 (AR15Discounts SigSaueralpha-msrscopemount30mm...-1.jpg, the mount alone from the rear right and above, 1920 x 1280), 01f740a75f03 (Paducah Shooters 2750575.jpg, the mount alone from the front right, 1500 x 887)","scaleRef":"each ring's 30 mm bore (tube_od) and the rings' spacing (ring_front_x − ring_rear_x), through a camera fitted to each photo (.cache/scope/mountw/camfit.py: the four bore rims, and the split lines on the end face, the bore's wall and the near side flat, all in the bore's mid-plane; 0.1 to 0.7 px on the lines, 1 to 1.7 px on the rims; the cameras 27 to 28 in away)","method":"the split line where it crosses the near side flat, which lies in the bore's mid-plane: 0.844 and 0.843 in from the mount's mid-plane (the first photo, front and rear ring), 0.846 and 0.841 (the second), 0.834 and 0.847 (the third); twice their mean. Moving the camera's principal point 300 px moves it 0.002","via":"harvest"}}],"note":"Wider than they are tall (ring_od, 1.363, is across the top and bottom flats): the cap screws stand beside the tube. Each end face is narrower, 1.51 in, inside a bevel on its upright edges (ring_edge_bevel). A first reading of the wall along the split on the front ring's end face (0.186 in on the silhouette's side, 0.127 where the face meets the visible flat) took the face for the ring: 1.55."},"ring_top_flat_width":{"label":"Mount rings, their top flat across","kind":"length","measurements":[{"id":"obliques","value":0.61,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 f4997c570421 (German Sport Guns SOA20014.jpg, the mount alone from the front left and above, 3000 x 2000), eab80540c7f1 (AR15Discounts SigSaueralpha-msrscopemount30mm...-1.jpg, the mount alone from the rear right and above, 1920 x 1280), 01f740a75f03 (Paducah Shooters 2750575.jpg, the mount alone from the front right, 1500 x 887)","scaleRef":"each ring's 30 mm bore (tube_od) and the rings' spacing (ring_front_x − ring_rear_x), through a camera fitted to each photo (.cache/scope/mountw/camfit.py: the four bore rims, and the split lines on the end face, the bore's wall and the near side flat, all in the bore's mid-plane; 0.1 to 0.7 px on the lines, 1 to 1.7 px on the rims; the cameras 27 to 28 in away)","method":"three corners of each ring's top flat on the silhouette, solved with the camera: 0.632 and 0.595 (the first photo), 0.610 and 0.637, 0.606 and 0.594","via":"harvest"}}],"note":"With ring_width, ring_od and ring_side_flat_height it makes the chamfer between the side flat and the top one 35 degrees from level, not 45."},"ring_side_flat_height":{"label":"Mount rings, their side flat's height (half above the split, half below)","kind":"length","measurements":[{"id":"sides","value":0.62,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 b233f6119cb4 (AR15Discounts SigSaueralpha-msrscopemount30mm...-3.jpg, the mount alone, straight left side, 1920 x 1280), 41d06e7d03cf (the same seller's -2.jpg, straight right side)","scaleRef":"the rings' spacing in the same view (ring_front_x − ring_rear_x, 3.168 in for 1118.5 px): 353 px/in at the mount's mid-plane","method":"the brightness edges up a column through the rear ring: rows 326.2 and 546.7 about the split at 435.5 on the left view, 349.6 and 571.4 about 460.6 on the right; 0.31 in each way. An oblique (01f740a75f03) has the near flat's edges at +0.316 and -0.319","via":"harvest"}}]},"ring_length":{"label":"Mount rings, their length along the tube (face to face)","kind":"length","measurements":[{"id":"obliques","value":0.628,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 f4997c570421 (German Sport Guns SOA20014.jpg, the mount alone from the front left and above, 3000 x 2000), eab80540c7f1 (AR15Discounts SigSaueralpha-msrscopemount30mm...-1.jpg, the mount alone from the rear right and above, 1920 x 1280), 01f740a75f03 (Paducah Shooters 2750575.jpg, the mount alone from the front right, 1500 x 887)","scaleRef":"each ring's 30 mm bore (tube_od) and the rings' spacing (ring_front_x − ring_rear_x), through a camera fitted to each photo (.cache/scope/mountw/camfit.py: the four bore rims, and the split lines on the end face, the bore's wall and the near side flat, all in the bore's mid-plane; 0.1 to 0.7 px on the lines, 1 to 1.7 px on the rims; the cameras 27 to 28 in away)","method":"the distance between each bore's two rims, a free parameter of the camera's fit: 0.629, 0.632 and 0.618","via":"harvest"}}],"note":"A straight side view reads 0.64 to 0.65 for the near face's flat with its bevels, and 0.69 with the sliver of the far face that shows beside it."},"ring_edge_bevel":{"label":"Mount rings, the bevel between an end face and a side flat","kind":"length","measurements":[{"id":"obliques","value":0.085,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 f4997c570421 (German Sport Guns SOA20014.jpg, the mount alone from the front left and above, 3000 x 2000), 01f740a75f03 (Paducah Shooters 2750575.jpg, the mount alone from the front right, 1500 x 887)","scaleRef":"each ring's 30 mm bore (tube_od) and the rings' spacing (ring_front_x − ring_rear_x), through a camera fitted to each photo (.cache/scope/mountw/camfit.py: the four bore rims, and the split lines on the end face, the bore's wall and the near side flat, all in the bore's mid-plane; 0.1 to 0.7 px on the lines, 1 to 1.7 px on the rims; the cameras 27 to 28 in away)","method":"on the split's plane, the edge between the end face and the bevel lies 0.755 in from the mid-plane (0.755 and 0.754 in the two photos) and the edge between the bevel and the side flat 0.837, 0.07 to 0.09 in behind the face: about 45 degrees","via":"harvest"}}]},"ring_screw_z":{"label":"Ring cap screws, their axes from the mount's mid-plane","kind":"length","measurements":[{"id":"oblique","value":0.715,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 01f740a75f03 (Paducah Shooters 2750575.jpg, the mount alone from the front right, 1500 x 887)","scaleRef":"each ring's 30 mm bore (tube_od) and the rings' spacing (ring_front_x − ring_rear_x), through a camera fitted to each photo (.cache/scope/mountw/camfit.py: the four bore rims, and the split lines on the end face, the bore's wall and the near side flat, all in the bore's mid-plane; 0.1 to 0.7 px on the lines, 1 to 1.7 px on the rims; the cameras 27 to 28 in away)","method":"the front ring's two seats on the chamfer's plane: their outermost point 0.816 in from the mid-plane, their ends along the tube at 0.69 and 0.775; one photo","via":"harvest"}}],"note":"Four to a ring, two each side, 0.32 in apart along the tube. Each sits in a round seat cut down into the cap's chamfer, with a slot 0.15 in wide running up the chamfer from it; in the lower half a plain slot of that width runs down the lower chamfer under each."},"ring_screw_seat_d":{"label":"Ring cap screws, the round seat's diameter","kind":"length","measurements":[{"id":"sides","value":0.228,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 b233f6119cb4 (AR15Discounts SigSaueralpha-msrscopemount30mm...-3.jpg, the mount alone, straight left side, 1920 x 1280), 41d06e7d03cf (the same seller's -2.jpg, straight right side)","scaleRef":"the rings' spacing in the same view (ring_front_x − ring_rear_x, 3.168 in for 1118.5 px): 353 px/in at the mount's mid-plane","method":"each seat's width along the tube on a row through it: 82.4 and 82.3 px on the right view (566.1 to 648.5, 680.4 to 762.7), 79.6 and 78.9 on the left; an oblique (01f740a75f03) gives 0.235","via":"harvest"}}]},"ring_screw_seat_above_split":{"label":"Ring cap screws, the seat's floor above the split","kind":"length","measurements":[{"id":"side","value":0.326,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 41d06e7d03cf (the same seller's -2.jpg, straight right side)","scaleRef":"the rings' spacing in the same view (ring_front_x − ring_rear_x, 3.168 in for 1118.5 px): 353 px/in at the mount's mid-plane","method":"the seat's lowest row up a column through it (344.1) against the split (460.6); the slot above it ends 0.62 in above the split and meets the seat at 0.44","via":"harvest"}}]},"ring_screw_spacing":{"label":"Ring cap screws, the two on a side, centre to centre along the tube","kind":"length","measurements":[{"id":"sides","value":0.321,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 b233f6119cb4 (AR15Discounts SigSaueralpha-msrscopemount30mm...-3.jpg, the mount alone, straight left side, 1920 x 1280), 41d06e7d03cf (the same seller's -2.jpg, straight right side)","scaleRef":"the rings' spacing in the same view (ring_front_x − ring_rear_x, 3.168 in for 1118.5 px): 353 px/in at the mount's mid-plane","method":"the two seats' centres on each ring: columns 607.3 and 721.6 on the right view, 1195.9 and 1309.4 on the left (114.3 and 113.5 px)","via":"harvest"}}]},"ring_screw_slot_width":{"label":"Ring cap screws, the slot's width (up the cap's chamfer, and down the lower half's)","kind":"length","measurements":[{"id":"sides","value":0.148,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 b233f6119cb4 (AR15Discounts SigSaueralpha-msrscopemount30mm...-3.jpg, the mount alone, straight left side, 1920 x 1280), 41d06e7d03cf (the same seller's -2.jpg, straight right side)","scaleRef":"the rings' spacing in the same view (ring_front_x − ring_rear_x, 3.168 in for 1118.5 px): 353 px/in at the mount's mid-plane","method":"each slot's width on a row through it: 52.7 and 52.8 px on the right view (586.1 to 638.8, 698.9 to 751.7), 52.6 and 52.9 on the left","via":"harvest"}}]},"ring_screw_slot_top_above_split":{"label":"Ring cap screws, the slot's upper end above the split (as the side sees it)","kind":"length","measurements":[{"id":"side","value":0.62,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 41d06e7d03cf (the same seller's -2.jpg, straight right side)","scaleRef":"the rings' spacing in the same view (ring_front_x − ring_rear_x, 3.168 in for 1118.5 px): 353 px/in at the mount's mid-plane","method":"the slot's highest row up a column through it (237.4 to 241.8) against the split (460.6)","via":"harvest"}}]},"ring_lower_slot_bottom_below_split":{"label":"Ring lower half, its slots' lower end below the split (as the side sees it)","kind":"length","measurements":[{"id":"sides","value":0.62,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 b233f6119cb4 (AR15Discounts SigSaueralpha-msrscopemount30mm...-3.jpg, the mount alone, straight left side, 1920 x 1280), 41d06e7d03cf (the same seller's -2.jpg, straight right side)","scaleRef":"the rings' spacing in the same view (ring_front_x − ring_rear_x, 3.168 in for 1118.5 px): 353 px/in at the mount's mid-plane","method":"the slot's lowest rows up a column through it: 671.7 to 676.7 about the split at 460.6 on the right view (0.60 to 0.61 in), 650.7 to 680.7 about 435.5 on the left (0.61 to 0.69); the end is a shadow's, which is the ±","via":"harvest"}}],"note":"They begin at the side flat's foot (half of ring_side_flat_height below the split)."},"arm_pocket_depth":{"label":"Mount's arm, the depth of the pocket in each side","kind":"length","measurements":[{"id":"obliques","value":0.2,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 01f740a75f03 (Paducah Shooters 2750575.jpg, the mount alone from the front right, 1500 x 887), eab80540c7f1 (AR15Discounts ...-1.jpg, from the rear right, 1920 x 1280)","scaleRef":"each ring's 30 mm bore and the rings' spacing, through a camera fitted to each photo (.cache/scope/mountw/camfit.py)","method":"the width of the pocket's shadowed lower wall: 0.21 in (the first photo, column 800, rows 679.4 to 697.8) and 0.19 (the second, column 1200, rows 695.8 to 722.7)","via":"harvest"}}],"note":"Weak: it takes the dark band along each pocket's lower edge for its lower wall. With arm_width it leaves a web about 0.28 in thick between the two sides' pockets."},"arm_width":{"label":"Mount's arm, across","kind":"length","measurements":[{"id":"obliques","value":0.68,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 f4997c570421 (German Sport Guns SOA20014.jpg, the mount alone from the front left and above, 3000 x 2000), eab80540c7f1 (AR15Discounts SigSaueralpha-msrscopemount30mm...-1.jpg, the mount alone from the rear right and above, 1920 x 1280), 01f740a75f03 (Paducah Shooters 2750575.jpg, the mount alone from the front right, 1500 x 887)","scaleRef":"each ring's 30 mm bore (tube_od) and the rings' spacing (ring_front_x − ring_rear_x), through a camera fitted to each photo (.cache/scope/mountw/camfit.py: the four bore rims, and the split lines on the end face, the bore's wall and the near side flat, all in the bore's mid-plane; 0.1 to 0.7 px on the lines, 1 to 1.7 px on the rims; the cameras 27 to 28 in away)","method":"edges that run along the arm, each found in two photos and triangulated: its top's left edge 0.340 in from the mid-plane, its top's right edge 0.320, its bottom's right edge and the pocket's upper edge on the right both 0.346","via":"harvest"}}],"note":"A plain beam, narrower than the rings and than the base, with a blind pocket in each side (neither straight side view shows any background through them): the pockets read 0.20 ± 0.05 in deep by the width of what is taken for their shadowed lower wall, which is weak, so the model's pockets are an assumption."},"base_right_z":{"label":"Mount's base, its right (fixed) side's outer face from the mid-plane","kind":"length","measurements":[{"id":"obliques","value":0.6,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 eab80540c7f1 (AR15Discounts SigSaueralpha-msrscopemount30mm...-1.jpg, the mount alone from the rear right and above, 1920 x 1280), 01f740a75f03 (Paducah Shooters 2750575.jpg, the mount alone from the front right, 1500 x 887)","scaleRef":"each ring's 30 mm bore (tube_od) and the rings' spacing (ring_front_x − ring_rear_x), through a camera fitted to each photo (.cache/scope/mountw/camfit.py: the four bore rims, and the split lines on the end face, the bore's wall and the near side flat, all in the bore's mid-plane; 0.1 to 0.7 px on the lines, 1 to 1.7 px on the rims; the cameras 27 to 28 in away)","method":"on the base's rear end face: 0.594 in (the first photo); the lower chamfer's upper edge triangulated between the two, 0.605","via":"harvest"}}]},"base_top_width":{"label":"Mount's base, its top face across","kind":"length","measurements":[{"id":"obliques","value":0.7,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 f4997c570421 (German Sport Guns SOA20014.jpg, the mount alone from the front left and above, 3000 x 2000), eab80540c7f1 (AR15Discounts SigSaueralpha-msrscopemount30mm...-1.jpg, the mount alone from the rear right and above, 1920 x 1280)","scaleRef":"each ring's 30 mm bore (tube_od) and the rings' spacing (ring_front_x − ring_rear_x), through a camera fitted to each photo (.cache/scope/mountw/camfit.py: the four bore rims, and the split lines on the end face, the bore's wall and the near side flat, all in the bore's mid-plane; 0.1 to 0.7 px on the lines, 1 to 1.7 px on the rims; the cameras 27 to 28 in away)","method":"on the rear end face: the seam with the bar 0.350 in left of the mid-plane (0.362 triangulated, 0.308 in the first photo) and the top's right corner 0.346 right of it","via":"harvest"}}],"note":"Level with the base's top as the side view has it. On the right the side slopes out and down from it to base_right_z by about 0.3 in below the top; on the left it ends at the seam with the clamp bar, whose top is 0.075 in lower."},"base_foot_right_z":{"label":"Mount's base, its right side's lowest edge from the mid-plane","kind":"length","measurements":[{"id":"obliques","value":0.44,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 eab80540c7f1 (AR15Discounts SigSaueralpha-msrscopemount30mm...-1.jpg, the mount alone from the rear right and above, 1920 x 1280), 01f740a75f03 (Paducah Shooters 2750575.jpg, the mount alone from the front right, 1500 x 887)","scaleRef":"each ring's 30 mm bore (tube_od) and the rings' spacing (ring_front_x − ring_rear_x), through a camera fitted to each photo (.cache/scope/mountw/camfit.py: the four bore rims, and the split lines on the end face, the bore's wall and the near side flat, all in the bore's mid-plane; 0.1 to 0.7 px on the lines, 1 to 1.7 px on the rims; the cameras 27 to 28 in away)","method":"the bottom silhouette's edge triangulated between the two photos, 0.432 in; a point on it in the first, 0.43 to 0.45","via":"harvest"}}],"note":"The right side's face is upright from about 0.3 to 0.47 in below the base's top, then chamfered in to this."},"clamp_bar_outer_z":{"label":"Clamp bar, its outer face from the mid-plane (left)","kind":"length","measurements":[{"id":"obliques","value":0.56,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 f4997c570421 (German Sport Guns SOA20014.jpg, the mount alone from the front left and above, 3000 x 2000), eab80540c7f1 (AR15Discounts SigSaueralpha-msrscopemount30mm...-1.jpg, the mount alone from the rear right and above, 1920 x 1280)","scaleRef":"each ring's 30 mm bore (tube_od) and the rings' spacing (ring_front_x − ring_rear_x), through a camera fitted to each photo (.cache/scope/mountw/camfit.py: the four bore rims, and the split lines on the end face, the bore's wall and the near side flat, all in the bore's mid-plane; 0.1 to 0.7 px on the lines, 1 to 1.7 px on the rims; the cameras 27 to 28 in away)","method":"0.553 in on the rear end face (the second photo), 0.561 triangulated, 0.566 in the first","via":"harvest"}}]},"clamp_bar_thickness":{"label":"Clamp bar, its thickness (across)","kind":"length","measurements":[{"id":"obliques","value":0.21,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.clamp_bar_outer_z} - {.base_top_width} / 2","via":"harvest"}}],"note":"From its seam with the base (base_top_width's left end) to its outer face; the seam is a hairline."},"clamp_bolt_spacing":{"label":"Clamp cross bolts, centre to centre","kind":"length","measurements":[{"id":"slots","value":1.97,"unit":"in","source":{"type":"derived","expr":"5 * {std.picatinny.slot_pitch}","via":"harvest"}},{"id":"mount","value":2,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 41d06e7d03cf and b233f6119cb4 (AR15Discounts, the mount alone, straight right and left sides, 1920 x 1280), eab80540c7f1 (AR15Discounts SigSaueralpha-msrscopemount30mm...-1.jpg, the mount alone from the rear right and above, 1920 x 1280), 01f740a75f03 (Paducah Shooters 2750575.jpg, the mount alone from the front right, 1500 x 887)","scaleRef":"the rings' spacing in each side view (353 px/in at the mid-plane, the heads and nuts 1.3% nearer the lens at about 75 in); the fitted cameras for the obliques","method":"the two bolt heads in the right view, 1.99 in apart; the two nuts in the left, 2.02; the bolts' axes triangulated between the two obliques, 1.986","via":"harvest"}}],"adopt":{"from":"slots","reason":"Both bolts lie in recoil slots, which are a whole number of pitches apart. The mount's own photos read 0.03 in more, three ways, but all three hang on one scale (the rings' spacing, good to 1%), which can't tell 1.97 from 2.00; a slot's clearance round a bolt would allow either."},"note":"Each bolt lies in a rail slot. Their heads read 2.01 in apart in the right-side photo and their nuts 2.03 in the left, at the tube's scale; both stand nearer the lens than the tube (1 to 2% large). Five slots."},"clamp_bolt_below_rail_top":{"label":"Clamp cross bolts, their axis below the rail's top","kind":"length","measurements":[{"id":"right","value":0.01,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a0aec57f834a (German Sport Guns SOT61000.jpg, right side)","scaleRef":"the 30 mm tube: 233.7 px/in; the optical axis 1.535 in above the rail's top (optical_axis_above_rail)","method":"the two heads' centres are at row 1375 on a gridded 2x crop, 361 px (1.545 in) below the tube's axis; ± covers the lens standing a few degrees above the axis, which shows the near heads about 0.04 in low","via":"harvest"}}],"note":"A cross bolt lies in a recoil slot, which is 0.118 in deep: its axis has to be about at the rail's top."},"clamp_bolt_head_d":{"label":"Clamp cross bolt, head diameter (right side)","kind":"length","measurements":[{"id":"right","value":0.32,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a0aec57f834a (German Sport Guns SOT61000.jpg, right side)","scaleRef":"the 30 mm tube: 233.7 px/in in the axis's plane; the heads stand about 0.65 in nearer the lens (2% large)","method":"each round head is 76 to 78 px across on a gridded 2x crop (columns 1070–1148 and 1540–1618)","via":"harvest"}}]},"clamp_nut_af":{"label":"Clamp cross bolt, nut across flats (left side)","kind":"length","measurements":[{"id":"third-coast","value":0.5,"unit":"in","stated":"To Rail: 65 in/lbs (1/2in Nut)","source":{"type":"spec","publisher":"retailer","name":"Third Coast Thermal, ALPHA-MSR scope mount (torque specifications)","url":"https://www.thirdcoastthermal.com/collections/rings-and-mounts/products/alpha-msr-scope-mount","retrieved":"2026-10-01","via":"harvest"},"note":"A 1/2 in wrench size. The engraving beside the nuts reads 65 in - lb."}]},"clamp_bolt_head_h":{"label":"Clamp cross bolt, how far its head stands out of the clamp (right side)","kind":"length","measurements":[{"id":"oblique","value":0.1,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 9f208491beb5 (German Sport Guns SOT61000_3.jpg, from the front right)","scaleRef":"the head's own diameter (clamp_bolt_head_d) beside it","method":"by eye: a low dome, about a third of its diameter proud","via":"harvest"}},{"id":"cameras","value":0.05,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 eab80540c7f1 (AR15Discounts SigSaueralpha-msrscopemount30mm...-1.jpg, the mount alone from the rear right and above, 1920 x 1280), 01f740a75f03 (Paducah Shooters 2750575.jpg, the mount alone from the front right, 1500 x 887)","scaleRef":"each ring's 30 mm bore (tube_od) and the rings' spacing, through a camera fitted to each photo (.cache/scope/mountw/camfit.py)","method":"each head's face triangulated between the two photos, 0.617 to 0.628 in from the mid-plane, against the side's face at 0.60 (base_right_z); each sits in a recess 0.37 in across","via":"harvest"}}],"adopt":{"from":"cameras","reason":"Triangulated between two photos; the first was by eye, and the two agree within their spread."}},"clamp_nut_h":{"label":"Clamp cross bolt, how far its nut stands out of the clamp bar (left side)","kind":"length","measurements":[{"id":"oblique","value":0.35,"unit":"in","pm":0.1,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 f4997c570421 (German Sport Guns SOA20014.jpg, the mount alone from the front left)","scaleRef":"the nut's own 1/2 in across its flats","method":"by eye: the nut is about 0.7 of its width long","via":"harvest"}},{"id":"camera","value":0.54,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 f4997c570421 (German Sport Guns SOA20014.jpg, the mount alone from the front left and above, 3000 x 2000)","scaleRef":"each ring's 30 mm bore (tube_od) and the rings' spacing, through a camera fitted to each photo (.cache/scope/mountw/camfit.py)","method":"the stud's end, which lies inside the nut's recessed outer end, on the rear bolt's plane: 1.105 in from the mid-plane; less the bar's outer face (clamp_bar_outer_z). A round collar next to the bar, then the hex: where one ends and the other begins wasn't settled","via":"harvest"}}],"adopt":{"from":"camera","reason":"Read through the fitted camera against the bar's face; the first was by eye."}},"mount_length":{"label":"Mount's clamp length along the rail (at its foot)","kind":"length","measurements":[{"id":"right","value":2.838,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a0aec57f834a (German Sport Guns SOT61000.jpg, right side: the mount under the scope)","scaleRef":"scale from sig-tango-msr-1-6x24.tube_od = 1.1811 in, the tube's own width column by column: 276.1 px over columns 1170–1350, 275.5 px over columns 1545–1640, 274.6 px over columns 2025–2060, 273.0 px over columns 2290–2660; a line through them (rms 0.28 px) changes -1.5% from column 1170 to 2660, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1500)/width, the lens's axis taken to meet the image at column 1500; 233.4 px/in there. The axis is the tube's centre line (tilt -0.23°, rms 0.19 px). Lengths then scaled by 1.0125 so that the end faces are sig-tango-msr-1-6x24.length = 10.4 in apart: at the tube's scale they read 10.272 (-1.2%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.160 in over radius 0.591 (rms 0.002), the rear end's rim sags 0.055 in over radius 0.913 (rms 0.005)","method":"width in y [-1.79, -1.76] of the traced outline (tools/trace.py); the clamp's length at its foot (its front face slopes: 0.27 in longer at the top)","via":"harvest"}}]}}},{"subject":"sig-romeo-msr-gen-2","title":"SIG Sauer ROMEO-MSR GEN II red dot sight, 2 MOA red dot (SORMSR101), on the see-through riser it comes on","dimensions":{"length":{"label":"Overall length","kind":"length","measurements":[{"id":"sheet","value":69.7,"unit":"mm","stated":"OVERALL LENGTH 2.7 in 69.7 mm","source":{"type":"spec","publisher":"manufacturer","name":"SIG Sauer, ROMEO-MSR GEN II 1x20 mm spec sheet (REV. 2.7.2024), the PDF as OpticsPlanet hosts it","url":"https://www.opticsplanet.com/i/pdf/opplanet-sig-sauer-romeo-msr-gen-ii-rifle-red-dot-sight-spec-sheet-pdf.pdf","retrieved":"2026-10-05","via":"harvest"}},{"id":"impact","value":2.7,"unit":"in","pm":0.05,"stated":"Length : 2.70\"","source":{"type":"spec","publisher":"retailer","name":"Impact Guns, SIG ROMEO-MSR Gen 2 red dot 1x20mm black (798681694624, SORMSR101), specifications","url":"https://www.impactguns.com/reflex-sights/sig-romeo-msr-gen-2-red-dot-1x20mm-black-798681694624-sormsr101","retrieved":"2026-10-05","via":"harvest"},"note":"The sheet's 2.7 in with a zero written after it: no closer than the sheet's own inches."}],"adopt":{"from":"sheet","reason":"SIG's own sheet, in the unit it gives to three figures; the seller's inches round it."}},"width":{"label":"Overall width (the raised panel's face on the left flank to the brightness dial's face, on the right)","kind":"length","measurements":[{"id":"sheet","value":44.8,"unit":"mm","stated":"OVERALL WIDTH 1.8 in 44.8 mm","source":{"type":"spec","publisher":"manufacturer","name":"SIG Sauer, ROMEO-MSR GEN II 1x20 mm spec sheet (REV. 2.7.2024), the PDF as OpticsPlanet hosts it","url":"https://www.opticsplanet.com/i/pdf/opplanet-sig-sauer-romeo-msr-gen-ii-rifle-red-dot-sight-spec-sheet-pdf.pdf","retrieved":"2026-10-05","via":"harvest"}},{"id":"impact","value":1.8,"unit":"in","stated":"Width : 1.8\"","source":{"type":"spec","publisher":"retailer","name":"Impact Guns, SIG ROMEO-MSR Gen 2 red dot 1x20mm black (798681694624, SORMSR101), specifications","url":"https://www.impactguns.com/reflex-sights/sig-romeo-msr-gen-2-red-dot-1x20mm-black-798681694624-sormsr101","retrieved":"2026-10-05","via":"harvest"}}],"adopt":{"from":"sheet","reason":"SIG's own sheet, in the unit it gives to three figures; the seller's inches round it."},"note":"The sheet doesn't say what it spans: it is taken across the two things that stand furthest out, the raised panel on the left flank and the dial on the right. The photo from behind gives how the width divides between them (left_panel_reach_z: 0.68 in left of the axis, so the dial's face 1.08 in right of it). Until 2026-10-05 the left side was taken as the round tube's (0.584 in) and the dial's face stood 1.18 in out."},"height":{"label":"Overall height (the clamp's bottom to the elevation turret's top, on its riser)","kind":"length","measurements":[{"id":"sheet","value":62.9,"unit":"mm","stated":"OVERALL HEIGHT 2.5 in 62.9 mm","source":{"type":"spec","publisher":"manufacturer","name":"SIG Sauer, ROMEO-MSR GEN II 1x20 mm spec sheet (REV. 2.7.2024), the PDF as OpticsPlanet hosts it","url":"https://www.opticsplanet.com/i/pdf/opplanet-sig-sauer-romeo-msr-gen-ii-rifle-red-dot-sight-spec-sheet-pdf.pdf","retrieved":"2026-10-05","via":"harvest"}},{"id":"impact","value":2.5,"unit":"in","pm":0.05,"stated":"Height : 2.50\"","source":{"type":"spec","publisher":"retailer","name":"Impact Guns, SIG ROMEO-MSR Gen 2 red dot 1x20mm black (798681694624, SORMSR101), specifications","url":"https://www.impactguns.com/reflex-sights/sig-romeo-msr-gen-2-red-dot-1x20mm-black-798681694624-sormsr101","retrieved":"2026-10-05","via":"harvest"},"note":"The sheet's 2.5 in with a zero written after it: no closer than the sheet's own inches."}],"adopt":{"from":"sheet","reason":"SIG's own sheet, in the unit it gives to three figures; the seller's inches round it."},"note":"From the bottom of the riser's rail clamp, not the rail's top: two straight side views scaled by the sheet's length read 2.48 and 2.49 in between those two (the sheet: 62.9 mm, 2.476 in)."},"optical_axis_above_rail":{"label":"Optical axis above the rail's top (on the riser it comes on)","kind":"length","measurements":[{"id":"sheet","value":1.41,"unit":"in","stated":"SIGHT HEIGHT 1.41\" ABSOLUTE CO-WITNESS","source":{"type":"spec","publisher":"manufacturer","name":"SIG Sauer, ROMEO-MSR GEN II 1x20 mm spec sheet (REV. 2.7.2024), the PDF as OpticsPlanet hosts it","url":"https://www.opticsplanet.com/i/pdf/opplanet-sig-sauer-romeo-msr-gen-ii-rifle-red-dot-sight-spec-sheet-pdf.pdf","retrieved":"2026-10-05","via":"harvest"}},{"id":"impact","value":1.41,"unit":"in","stated":"Mount Height : 1.41\"","source":{"type":"spec","publisher":"retailer","name":"Impact Guns, SIG ROMEO-MSR Gen 2 red dot 1x20mm black (798681694624, SORMSR101), specifications","url":"https://www.impactguns.com/reflex-sights/sig-romeo-msr-gen-2-red-dot-1x20mm-black-798681694624-sormsr101","retrieved":"2026-10-05","via":"harvest"}}],"adopt":{"from":"sheet","reason":"SIG's own sheet; the seller repeats it."},"note":"SIG's \"sight height\", with \"absolute co-witness\" beside it: taken as the rail's top to the optical axis, as a sight height is given. The side view agrees with it only through the clamp's depth, which nothing else gives (clamp_below_rail)."},"weight":{"label":"Weight without its battery (the sheet's figure; it doesn't say whether the riser is in it)","kind":"mass","measurements":[{"id":"sheet","value":5.7,"unit":"oz","stated":"WEIGHT W/O BATTERY 5.7 oz 161 g","source":{"type":"spec","publisher":"manufacturer","name":"SIG Sauer, ROMEO-MSR GEN II 1x20 mm spec sheet (REV. 2.7.2024), the PDF as OpticsPlanet hosts it","url":"https://www.opticsplanet.com/i/pdf/opplanet-sig-sauer-romeo-msr-gen-ii-rifle-red-dot-sight-spec-sheet-pdf.pdf","retrieved":"2026-10-05","via":"harvest"}},{"id":"pa","value":5.7,"unit":"oz","stated":"Weight 5.7 oz","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, SIG Sauer ROMEO-MSR GEN II 2 MOA red dot sight (SORMSR101), specifications","url":"https://www.primaryarms.com/sig-sauer-romeo-msr-gen-ii-2-moa-red-dot-sight","retrieved":"2026-10-05","via":"harvest"}},{"id":"impact","value":5.7,"unit":"oz","stated":"Weight : 5.7 oz","source":{"type":"spec","publisher":"retailer","name":"Impact Guns, SIG ROMEO-MSR Gen 2 red dot 1x20mm black (798681694624, SORMSR101), specifications","url":"https://www.impactguns.com/reflex-sights/sig-romeo-msr-gen-2-red-dot-1x20mm-black-798681694624-sormsr101","retrieved":"2026-10-05","via":"harvest"}}],"adopt":{"from":"sheet","reason":"SIG's own sheet, which says what it leaves out; two sellers repeat the figure."},"note":"\"W/O BATTERY\" is the sheet's; a CR2032's own weight is on no page on file and isn't added. The sight is sold only on its riser, and the sheet names no weight without one."},"sight_weight":{"label":"Weight of the sight alone (off its riser)","kind":"mass","measurements":[{"id":"sheet-less-riser","value":3.9,"unit":"oz","pm":0.4,"source":{"type":"derived","expr":"{.weight} - {sig-romeo-msr-riser-mount.weight}","via":"harvest"},"note":"5.7 oz less the riser's metal, 1.8 oz."}],"note":"SIG gives one weight, the sight on its riser without its battery (weight: taken to be that, the sight being sold only on it). The sight alone is that less the riser, whose weight is its metal (sig-romeo-msr-riser-mount.weight): the two add up to the sheet's figure, so a build's weight doesn't move with the split (D101)."},"window_d":{"label":"Objective lens diameter","kind":"length","measurements":[{"id":"sheet","value":20,"unit":"mm","stated":"OBJECTIVE LENS 20 mm","source":{"type":"spec","publisher":"manufacturer","name":"SIG Sauer, ROMEO-MSR GEN II 1x20 mm spec sheet (REV. 2.7.2024), the PDF as OpticsPlanet hosts it","url":"https://www.opticsplanet.com/i/pdf/opplanet-sig-sauer-romeo-msr-gen-ii-rifle-red-dot-sight-spec-sheet-pdf.pdf","retrieved":"2026-10-05","via":"harvest"}}],"note":"Draws the lens at the front; the rear window's own size isn't published and is drawn the same."},"axis_above_clamp_bottom":{"label":"Optical axis above the riser clamp's bottom","kind":"length","measurements":[{"id":"pa-side","value":1.655,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/sig-romeo-msr-gen-2 befa92096e57 (Primary Arms SORMSR101_02, the sight on its riser, straight left side on white, 2200 x 1467, objective to the left)","scaleRef":"the sheet's length, 69.7 mm = 1403 px (511.3 px/in), and its height, 62.9 mm = 1274 px (514.5 px/in), which agree within 0.6%: 512.9 px/in","method":"the objective bezel's ring is round about the axis: the middle of the dark run through it at five columns 0.10 to 0.30 in behind its front reads 1.655 to 1.656 in above the silhouette's lowest row, the clamp's bottom (.cache/batch123/sig-romeo-msr-gen-2/cols.py)","via":"harvest"},"note":"The ± is the two scales' 0.6% over this height and a pixel at each end."}]},"clamp_below_rail":{"label":"Riser clamp's bottom below the rail's top","kind":"length","measurements":[{"id":"derived","value":0.245,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{.axis_above_clamp_bottom} - {.optical_axis_above_rail}","via":"harvest"},"note":"The jaws wrap the rail's sides: the HM3X's reach 0.22 in and the ARO's 0.23. The photo from behind reads 0.234 in on its own scale."}]},"clamp_bottom_y":{"label":"Riser clamp's bottom in the optic frame (y, the rail's top is 0)","kind":"length","measurements":[{"id":"derived","value":-0.245,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"-{.clamp_below_rail}","via":"harvest"},"note":"Where the side profile's clamp-bottom origin sits in the part frame."}]},"tube_od":{"label":"Main tube OD (twice its underside's distance below the axis)","kind":"length","measurements":[{"id":"pa-side","value":1.168,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sig-romeo-msr-gen-2 befa92096e57 (Primary Arms SORMSR101_02, the sight on its riser, straight left side on white, 2200 x 1467, objective to the left)","scaleRef":"the sheet's length, 69.7 mm = 1403 px (511.3 px/in), and its height, 62.9 mm = 1274 px (514.5 px/in), which agree within 0.6%: 512.9 px/in","method":"the silhouette's underside ahead of the riser (0.4 to 0.5 in behind the front: 1.072 and 1.070 in above the clamp's bottom) and behind it (2.5 in: 1.072) lies 0.583 to 0.585 in below the bezel's centre: twice 0.584","via":"harvest"},"note":"A dark tube's edge on white reads a little thin: the ± allows 1.5%."}],"note":"Its top is under the housing and its sides aren't seen square on: the tube is taken as round about the axis, as the bezel ahead of it is and as the photo from behind shows its rear rim."},"tube_bottom_above_clamp_bottom":{"label":"The tube's underside where it overhangs the riser, above the riser clamp's bottom","kind":"length","measurements":[{"id":"pa-side","value":1.071,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/sig-romeo-msr-gen-2 befa92096e57 (Primary Arms SORMSR101_02, the sight on its riser, straight left side on white, 2200 x 1467, objective to the left)","scaleRef":"the sheet's length, 69.7 mm = 1403 px (511.3 px/in), and its height, 62.9 mm = 1274 px (514.5 px/in), which agree within 0.6%: 512.9 px/in","method":"the silhouette's underside just ahead of the riser's front and just behind its rear, where the body overhangs it: 1.070 to 1.072 in above the clamp's bottom","via":"harvest"}}],"note":"Called the riser's top until 2026-11-05, when the riser became a part of its own (D101): the riser's top is the seam with the housing's flat base, 0.013 in lower (base_above_clamp_bottom)."},"base_above_clamp_bottom":{"label":"The sight's own base (its seam with the riser's top) above the riser clamp's bottom","kind":"length","measurements":[{"id":"pa-side","value":1.058,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/sig-romeo-msr-gen-2 befa92096e57 (Primary Arms SORMSR101_02, the sight on its riser, straight left side on white, 2200 x 1467, objective to the left)","scaleRef":"the sheet's length, 69.7 mm = 1403 px (511.3 px/in), and its height, 62.9 mm = 1274 px (514.5 px/in), which agree within 0.6%: 512.9 px/in","method":"the darkest row of the seam line between the housing's base and the riser, in ten bands of 60 columns from column 700 to 1660: rows 828 (front) to 825 (rear), the silhouette's lowest row (the clamp's bottom) 1369: 1.055 to 1.061 in at 512.9 px/in (.cache/dots/msr_seam.py in the worktree of 2026-11-05)","via":"harvest"}}],"note":"Where the housing's flat base comes down onto the riser, and so the plane the sight's footprint meets a mount's deck in (D101): the housing's flank runs down past the round tube to a flat base the riser's length, with ROMEO-MSR printed on it, and a dark line parts it from the riser along its whole length. SIG's rendering of the flat dark earth sight (c4fea0598ed4) has that base in the housing's tan, down to the riser's black top. The line falls 0.006 in from the rear end to the front over 900 px, less than its own width: the photo's roll or the part's, and read as level."},"axis_above_base":{"label":"Optical axis above the sight's own base (the plane its footprint meets a mount's deck in: D101)","kind":"length","measurements":[{"id":"pa-side","value":0.597,"unit":"in","pm":0.014,"source":{"type":"derived","expr":"{.axis_above_clamp_bottom} - {.base_above_clamp_bottom}","via":"harvest"},"note":"1.655 in less 1.058, both on Primary Arms' side view at one scale."}],"note":"What the sight brings to any Micro-footprint mount (D101): its axis this far over the deck it is screwed to. On its own riser it puts the axis at SIG's 1.41 in, which is what the riser's deck height is worked out from (sig-romeo-msr-riser-mount.deck_above_rail). The photo from behind (ff6f13b2efd1) reads the riser's top 0.584 in under the axis through its camera; it was taken there to be the tube's underside, the same 0.584, and isn't a reading of the seam."},"mount_length":{"label":"Riser's length along the rail (its clamp's)","kind":"length","measurements":[{"id":"pa-side","value":1.973,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/sig-romeo-msr-gen-2 befa92096e57 (Primary Arms SORMSR101_02, the sight on its riser, straight left side on white, 2200 x 1467, objective to the left)","scaleRef":"the sheet's length, 69.7 mm = 1403 px (511.3 px/in), and its height, 62.9 mm = 1274 px (514.5 px/in), which agree within 0.6%: 512.9 px/in","method":"the silhouette's row widths over the riser, 0.60 to 0.97 of the height down from the top: 1001 to 1014 px, median 1012","via":"harvest"},"note":"Five rail slots' worth (1.97 in at std.picatinny.slot_pitch)."}]},"riser_width":{"label":"Riser's width across its two legs","kind":"length","measurements":[{"id":"gat-rear","value":1.113,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sig-romeo-msr-gen-2 ff6f13b2efd1 (GAT Daily's review, a phone photo from behind the sight on a rifle's rail, looking forward through it, 3024 x 1701)","scaleRef":"a pinhole camera fitted to two sizes on the sight's own axis: the tube's rear rim, a circle of radius 273 px about (1450, 730), taken as tube_od (1.168 in) 0.24 in ahead of the rear face, and the objective lens seen through the tube, 250 px across, the sheet's 20 mm, 2.6 in ahead of it: the lens stood 4.76 in behind the rear face and a length t in ahead of that face reads 2335.6 / (4.756 + t) px/in. Checked on what it wasn't fitted to: the clamp's bottom reads 0.234 in below the rail's top (0.245 by the side view), the riser's top 0.584 in below the axis (0.584), the turret's top 0.847 in above it (0.829). Across the sight the axis is column 1479: the window's centre, with the riser's two legs centred on 1477.5 (the circle's 1450 is 29 px left of it: its left side was fitted to the raised panel on the left flank, which stands out past the rim; until 2026-10-05 the dial's face was read from 1450 as 1.177 in right of the axis and, with the tube's 0.584 in taken as the left side, seemed to make the sheet's width: left_panel_reach_z has what the photo gives)","method":"the legs' outer edges at the riser's rear face (0.244 in ahead of the body's rear face by the side view), columns 1220 and 1740: 520 px at 467.1 px/in","via":"harvest"},"note":"A rail's 0.835 in between two jaws of about 0.14 in each. The ± is 10 px of reading and the camera's fit."}]},"riser_neck_width":{"label":"Riser's width at its top, under the body (above its shoulders)","kind":"length","measurements":[{"id":"gat-rear","value":0.856,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sig-romeo-msr-gen-2 ff6f13b2efd1 (GAT Daily's review, a phone photo from behind the sight on a rifle's rail, looking forward through it, 3024 x 1701)","scaleRef":"a pinhole camera fitted to two sizes on the sight's own axis: the tube's rear rim, a circle of radius 273 px about (1450, 730), taken as tube_od (1.168 in) 0.24 in ahead of the rear face, and the objective lens seen through the tube, 250 px across, the sheet's 20 mm, 2.6 in ahead of it: the lens stood 4.76 in behind the rear face and a length t in ahead of that face reads 2335.6 / (4.756 + t) px/in. Checked on what it wasn't fitted to: the clamp's bottom reads 0.234 in below the rail's top (0.245 by the side view), the riser's top 0.584 in below the axis (0.584), the turret's top 0.847 in above it (0.829). Across the sight the axis is column 1479: the window's centre, with the riser's two legs centred on 1477.5 (the circle's 1450 is 29 px left of it: its left side was fitted to the raised panel on the left flank, which stands out past the rim; until 2026-10-05 the dial's face was read from 1450 as 1.177 in right of the axis and, with the tube's 0.584 in taken as the left side, seemed to make the sheet's width: left_panel_reach_z has what the photo gives)","method":"the riser's top where the body sits on it, columns 1280 to 1680 at rows 1000 to 1020: 400 px at 467.1 px/in; its shoulders slope from there out to the legs' width by row 1095","via":"harvest"}}]},"riser_shoulder_below_top":{"label":"How far below the riser's top its shoulders reach the legs' full width","kind":"length","measurements":[{"id":"gat-rear","value":0.197,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sig-romeo-msr-gen-2 ff6f13b2efd1 (GAT Daily's review, a phone photo from behind the sight on a rifle's rail, looking forward through it, 3024 x 1701)","scaleRef":"a pinhole camera fitted to two sizes on the sight's own axis: the tube's rear rim, a circle of radius 273 px about (1450, 730), taken as tube_od (1.168 in) 0.24 in ahead of the rear face, and the objective lens seen through the tube, 250 px across, the sheet's 20 mm, 2.6 in ahead of it: the lens stood 4.76 in behind the rear face and a length t in ahead of that face reads 2335.6 / (4.756 + t) px/in. Checked on what it wasn't fitted to: the clamp's bottom reads 0.234 in below the rail's top (0.245 by the side view), the riser's top 0.584 in below the axis (0.584), the turret's top 0.847 in above it (0.829). Across the sight the axis is column 1479: the window's centre, with the riser's two legs centred on 1477.5 (the circle's 1450 is 29 px left of it: its left side was fitted to the raised panel on the left flank, which stands out past the rim; until 2026-10-05 the dial's face was read from 1450 as 1.177 in right of the axis and, with the tube's 0.584 in taken as the left side, seemed to make the sheet's width: left_panel_reach_z has what the photo gives)","method":"the shoulders' slopes end on the legs' outer faces at row 1095 on both sides, 92 px below the riser's top (row 1003) at 467.1 px/in","via":"harvest"}}]},"riser_opening_width":{"label":"Width of the opening through the riser (the see-through)","kind":"length","measurements":[{"id":"gat-rear","value":0.841,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sig-romeo-msr-gen-2 ff6f13b2efd1 (GAT Daily's review, a phone photo from behind the sight on a rifle's rail, looking forward through it, 3024 x 1701)","scaleRef":"a pinhole camera fitted to two sizes on the sight's own axis: the tube's rear rim, a circle of radius 273 px about (1450, 730), taken as tube_od (1.168 in) 0.24 in ahead of the rear face, and the objective lens seen through the tube, 250 px across, the sheet's 20 mm, 2.6 in ahead of it: the lens stood 4.76 in behind the rear face and a length t in ahead of that face reads 2335.6 / (4.756 + t) px/in. Checked on what it wasn't fitted to: the clamp's bottom reads 0.234 in below the rail's top (0.245 by the side view), the riser's top 0.584 in below the axis (0.584), the turret's top 0.847 in above it (0.829). Across the sight the axis is column 1479: the window's centre, with the riser's two legs centred on 1477.5 (the circle's 1450 is 29 px left of it: its left side was fitted to the raised panel on the left flank, which stands out past the rim; until 2026-10-05 the dial's face was read from 1450 as 1.177 in right of the axis and, with the tube's 0.584 in taken as the left side, seemed to make the sheet's width: left_panel_reach_z has what the photo gives)","method":"the opening's side walls at the riser's rear face, columns 1282 and 1675: 393 px at 467.1 px/in","via":"harvest"},"note":"The rail's own width (std.picatinny.top_width, 0.835): the legs stand on its two edges."}]},"riser_opening_top_above_rail":{"label":"Top of the opening through the riser, above the rail's top","kind":"length","measurements":[{"id":"gat-rear","value":0.558,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sig-romeo-msr-gen-2 ff6f13b2efd1 (GAT Daily's review, a phone photo from behind the sight on a rifle's rail, looking forward through it, 3024 x 1701)","scaleRef":"a pinhole camera fitted to two sizes on the sight's own axis: the tube's rear rim, a circle of radius 273 px about (1450, 730), taken as tube_od (1.168 in) 0.24 in ahead of the rear face, and the objective lens seen through the tube, 250 px across, the sheet's 20 mm, 2.6 in ahead of it: the lens stood 4.76 in behind the rear face and a length t in ahead of that face reads 2335.6 / (4.756 + t) px/in. Checked on what it wasn't fitted to: the clamp's bottom reads 0.234 in below the rail's top (0.245 by the side view), the riser's top 0.584 in below the axis (0.584), the turret's top 0.847 in above it (0.829). Across the sight the axis is column 1479: the window's centre, with the riser's two legs centred on 1477.5 (the circle's 1450 is 29 px left of it: its left side was fitted to the raised panel on the left flank, which stands out past the rim; until 2026-10-05 the dial's face was read from 1450 as 1.177 in right of the axis and, with the tube's 0.584 in taken as the left side, seemed to make the sheet's width: left_panel_reach_z has what the photo gives)","method":"the opening's upper edge, row 1128, 398 px below the axis (row 730) at 467.1 px/in: 0.852 in below the axis, which is optical_axis_above_rail above the rail's top","via":"harvest"}}]},"riser_opening_bottom_above_rail":{"label":"Floor of the opening through the riser (its base's top), above the rail's top","kind":"length","measurements":[{"id":"gat-rear","value":0.119,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sig-romeo-msr-gen-2 ff6f13b2efd1 (GAT Daily's review, a phone photo from behind the sight on a rifle's rail, looking forward through it, 3024 x 1701)","scaleRef":"a pinhole camera fitted to two sizes on the sight's own axis: the tube's rear rim, a circle of radius 273 px about (1450, 730), taken as tube_od (1.168 in) 0.24 in ahead of the rear face, and the objective lens seen through the tube, 250 px across, the sheet's 20 mm, 2.6 in ahead of it: the lens stood 4.76 in behind the rear face and a length t in ahead of that face reads 2335.6 / (4.756 + t) px/in. Checked on what it wasn't fitted to: the clamp's bottom reads 0.234 in below the rail's top (0.245 by the side view), the riser's top 0.584 in below the axis (0.584), the turret's top 0.847 in above it (0.829). Across the sight the axis is column 1479: the window's centre, with the riser's two legs centred on 1477.5 (the circle's 1450 is 29 px left of it: its left side was fitted to the raised panel on the left flank, which stands out past the rim; until 2026-10-05 the dial's face was read from 1450 as 1.177 in right of the axis and, with the tube's 0.584 in taken as the left side, seemed to make the sheet's width: left_panel_reach_z has what the photo gives)","method":"the near edge of the base's top face, with its four slots, row 1333: 603 px below the axis at 467.1 px/in, 1.291 in below it","via":"harvest"}}]},"housing_width":{"label":"Width of the housing along the top (under the elevation turret)","kind":"length","measurements":[{"id":"gat-rear","value":0.51,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sig-romeo-msr-gen-2 ff6f13b2efd1 (GAT Daily's review, a phone photo from behind the sight on a rifle's rail, looking forward through it, 3024 x 1701)","scaleRef":"a pinhole camera fitted to two sizes on the sight's own axis: the tube's rear rim, a circle of radius 273 px about (1450, 730), taken as tube_od (1.168 in) 0.24 in ahead of the rear face, and the objective lens seen through the tube, 250 px across, the sheet's 20 mm, 2.6 in ahead of it: the lens stood 4.76 in behind the rear face and a length t in ahead of that face reads 2335.6 / (4.756 + t) px/in. Checked on what it wasn't fitted to: the clamp's bottom reads 0.234 in below the rail's top (0.245 by the side view), the riser's top 0.584 in below the axis (0.584), the turret's top 0.847 in above it (0.829). Across the sight the axis is column 1479: the window's centre, with the riser's two legs centred on 1477.5 (the circle's 1450 is 29 px left of it: its left side was fitted to the raised panel on the left flank, which stands out past the rim; until 2026-10-05 the dial's face was read from 1450 as 1.177 in right of the axis and, with the tube's 0.584 in taken as the left side, seemed to make the sheet's width: left_panel_reach_z has what the photo gives)","method":"the housing's two flanks above the tube's rim, columns 1335 and 1560 (225 px) at rows 380 to 480, taken 0.5 to 0.6 in ahead of the rear face (444 to 436 px/in): 0.506 to 0.516 in","via":"harvest"},"note":"Where along the sight the flanks seen from behind lie is read off the side view's slope; the ± covers a quarter inch of it."}]},"left_panel_reach_z":{"label":"The raised panel on the left flank: how far left of the axis its face stands","kind":"length","measurements":[{"id":"gat-rear","value":0.68,"unit":"in","pm":0.035,"source":{"type":"photo","photo":"references/sig-romeo-msr-gen-2 ff6f13b2efd1 (GAT Daily's review, a phone photo from behind the sight on a rifle's rail, looking forward through it, 3024 x 1701)","scaleRef":"the sheet's overall width (44.8 mm, 1.764 in) as what the panel's reach and the dial's add up to; the photo gives their ratio, each read at its own distance from the lens (the camera of this photo's other readings, 4.756 in behind the rear face)","method":"the sight's left edge is straight over rows 700 to 840 at column 1174.5 (a round rim would run in 9 px over those rows), 304.5 px left of the axis (column 1479: the window's centre; the riser's legs are centred on 1477.5), and is 18 and 22 px further in at rows 640 and 880, where the panel's swell about the medallion shows, 0.33 in further off (a flat face along the sight would step 19 px): it is the panel's rear end, 0.22 in ahead of the rear face by the side view. The dial's edge on the same rows is column 1878.5, 399.5 px right of the axis, its rear rim 1.24 in ahead of the rear face (dial_from_front less half dial_od). The reaches are as 304.5 x 4.976 to 399.5 x 5.995, 1 to 1.581: 0.683 and 1.081 of the sheet's 1.764","via":"harvest"},"note":"The ± covers 0.7 in of the lens's distance, 0.1 in of where each edge is along the sight, 2 px on each, and the camera's own scale, by which the two read 0.649 and 1.025 in (1.674 in all, 5% under the sheet). It doesn't cover the sheet's width spanning something else."}],"note":"The flat panel with SIG SAUER on it and the medallion at its rear (profiles.side has its outline as a feature). From behind it is the sight's left edge, not the tube's rim. The photo gives the ratio of its reach to the dial's; the sheet's overall width, taken across the two, gives the sizes: the dial's face is the width less this."},"dial_od":{"label":"Brightness dial's diameter (the knurled ring, on the right)","kind":"length","measurements":[{"id":"gat-rear","value":1.09,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/sig-romeo-msr-gen-2 ff6f13b2efd1 (GAT Daily's review, a phone photo from behind the sight on a rifle's rail, looking forward through it, 3024 x 1701)","scaleRef":"a pinhole camera fitted to two sizes on the sight's own axis: the tube's rear rim, a circle of radius 273 px about (1450, 730), taken as tube_od (1.168 in) 0.24 in ahead of the rear face, and the objective lens seen through the tube, 250 px across, the sheet's 20 mm, 2.6 in ahead of it: the lens stood 4.76 in behind the rear face and a length t in ahead of that face reads 2335.6 / (4.756 + t) px/in. Checked on what it wasn't fitted to: the clamp's bottom reads 0.234 in below the rail's top (0.245 by the side view), the riser's top 0.584 in below the axis (0.584), the turret's top 0.847 in above it (0.829). Across the sight the axis is column 1479: the window's centre, with the riser's two legs centred on 1477.5 (the circle's 1450 is 29 px left of it: its left side was fitted to the raised panel on the left flank, which stands out past the rim; until 2026-10-05 the dial's face was read from 1450 as 1.177 in right of the axis and, with the tube's 0.584 in taken as the left side, seemed to make the sheet's width: left_panel_reach_z has what the photo gives)","method":"the dial seen edge on, its knurls' tips at rows 540 and 930 (390 px), 1.79 in ahead of the rear face (dial_from_front) at 356.8 px/in","via":"harvest"},"note":"The ± covers 0.2 in of where along the sight the dial stands and 8 px of reading. Its centre reads 0.014 in below the axis: on it. How far in toward the tube its ring begins isn't seen from behind (the windage boss stands before it)."}]},"dial_from_front":{"label":"Brightness dial's axis behind the sight's front face","kind":"length","measurements":[{"id":"impact-left","value":0.96,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/sig-romeo-msr-gen-2 08c4c60c16c7 (Impact Guns sig-sormsr101-2, the left side from a little above, on white, 2000 x 2000: the dial's rim shows over the body's top)","scaleRef":"the sheet's length, 69.7 mm = 1372 px (500.0 px/in); its height reads 528 px/in in this photo, which is taken from above, so only a length along the sight is read","method":"the dial's knurled rim shows above the body's top edge between columns 640 and 905, a chord of a circle about its axis: its middle, column 772, is 480 px behind the front face (column 292)","via":"harvest"},"note":"The dial is on the far side of the sight in this photo, 1.7 in further from the lens: from a studio distance that is 0.02 in toward the photo's middle, inside the ±."}]},"windage_od":{"label":"Windage turret's boss: its diameter (on the right, behind the dial)","kind":"length","measurements":[{"id":"gat-rear","value":0.64,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/sig-romeo-msr-gen-2 ff6f13b2efd1 (GAT Daily's review, a phone photo from behind the sight on a rifle's rail, looking forward through it, 3024 x 1701)","scaleRef":"a pinhole camera fitted to two sizes on the sight's own axis: the tube's rear rim, a circle of radius 273 px about (1450, 730), taken as tube_od (1.168 in) 0.24 in ahead of the rear face, and the objective lens seen through the tube, 250 px across, the sheet's 20 mm, 2.6 in ahead of it: the lens stood 4.76 in behind the rear face and a length t in ahead of that face reads 2335.6 / (4.756 + t) px/in. Checked on what it wasn't fitted to: the clamp's bottom reads 0.234 in below the rail's top (0.245 by the side view), the riser's top 0.584 in below the axis (0.584), the turret's top 0.847 in above it (0.829). Across the sight the axis is column 1479: the window's centre, with the riser's two legs centred on 1477.5 (the circle's 1450 is 29 px left of it: its left side was fitted to the raised panel on the left flank, which stands out past the rim; until 2026-10-05 the dial's face was read from 1450 as 1.177 in right of the axis and, with the tube's 0.584 in taken as the left side, seemed to make the sheet's width: left_panel_reach_z has what the photo gives)","method":"the boss marked R, seen from behind as a block from row 612 to row 890 (278 px), taken 0.6 in ahead of the rear face (436 px/in)","via":"harvest"},"note":"Where along the sight it stands isn't read on any straight view: the quarter views show it behind the dial, level with the elevation turret, and it is taken there. The ± covers 0.3 in of that."}]},"windage_reach_z":{"label":"Windage turret's cap: how far right of the axis it reaches","kind":"length","measurements":[{"id":"gat-rear","value":0.87,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/sig-romeo-msr-gen-2 ff6f13b2efd1 (GAT Daily's review, a phone photo from behind the sight on a rifle's rail, looking forward through it, 3024 x 1701)","scaleRef":"a pinhole camera fitted to two sizes on the sight's own axis: the tube's rear rim, a circle of radius 273 px about (1450, 730), taken as tube_od (1.168 in) 0.24 in ahead of the rear face, and the objective lens seen through the tube, 250 px across, the sheet's 20 mm, 2.6 in ahead of it: the lens stood 4.76 in behind the rear face and a length t in ahead of that face reads 2335.6 / (4.756 + t) px/in. Checked on what it wasn't fitted to: the clamp's bottom reads 0.234 in below the rail's top (0.245 by the side view), the riser's top 0.584 in below the axis (0.584), the turret's top 0.847 in above it (0.829). Across the sight the axis is column 1479: the window's centre, with the riser's two legs centred on 1477.5 (the circle's 1450 is 29 px left of it: its left side was fitted to the raised panel on the left flank, which stands out past the rim; until 2026-10-05 the dial's face was read from 1450 as 1.177 in right of the axis and, with the tube's 0.584 in taken as the left side, seemed to make the sheet's width: left_panel_reach_z has what the photo gives)","method":"the boss's right edge, column 1860, 381 px right of the axis (column 1479), taken 0.6 in ahead of the rear face (436 px/in)","via":"harvest"},"note":"Read as 0.94 in until 2026-10-05, from column 1450 (the middle of a circle fitted to the rim and, on its left, to the raised panel: the camera's note has it)."}]},"windage_below_axis":{"label":"Windage turret's centre below the optical axis","kind":"length","measurements":[{"id":"gat-rear","value":0.05,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sig-romeo-msr-gen-2 ff6f13b2efd1 (GAT Daily's review, a phone photo from behind the sight on a rifle's rail, looking forward through it, 3024 x 1701)","scaleRef":"a pinhole camera fitted to two sizes on the sight's own axis: the tube's rear rim, a circle of radius 273 px about (1450, 730), taken as tube_od (1.168 in) 0.24 in ahead of the rear face, and the objective lens seen through the tube, 250 px across, the sheet's 20 mm, 2.6 in ahead of it: the lens stood 4.76 in behind the rear face and a length t in ahead of that face reads 2335.6 / (4.756 + t) px/in. Checked on what it wasn't fitted to: the clamp's bottom reads 0.234 in below the rail's top (0.245 by the side view), the riser's top 0.584 in below the axis (0.584), the turret's top 0.847 in above it (0.829). Across the sight the axis is column 1479: the window's centre, with the riser's two legs centred on 1477.5 (the circle's 1450 is 29 px left of it: its left side was fitted to the raised panel on the left flank, which stands out past the rim; until 2026-10-05 the dial's face was read from 1450 as 1.177 in right of the axis and, with the tube's 0.584 in taken as the left side, seemed to make the sheet's width: left_panel_reach_z has what the photo gives)","method":"the boss's middle between rows 612 and 890, row 751, 21 px below the axis at 436 px/in","via":"harvest"}}]},"turret_from_front":{"label":"Elevation turret's axis behind the sight's front face","kind":"length","measurements":[{"id":"pa-side","value":2.1,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/sig-romeo-msr-gen-2 befa92096e57 (Primary Arms SORMSR101_02, the sight on its riser, straight left side on white, 2200 x 1467, objective to the left)","scaleRef":"the sheet's length, 69.7 mm = 1403 px (511.3 px/in), and its height, 62.9 mm = 1274 px (514.5 px/in), which agree within 0.6%: 512.9 px/in","method":"the silhouette's flat top, the turret's cap, runs from 2.0 to 2.2 in behind the front face at 2.484 in above the clamp's bottom: its middle","via":"harvest"}}]}}},{"subject":"sig-romeo-msr-riser-mount","title":"SIG Sauer's see-through riser mount, absolute co-witness (1.41 in), the mount the ROMEO-MSR GEN II is sold on","dimensions":{"deck_above_rail":{"label":"The riser's top (where a dot's base sits) above the rail's top","kind":"length","measurements":[{"id":"sheet-less-msr","value":0.813,"unit":"in","pm":0.014,"source":{"type":"derived","expr":"{sig-romeo-msr-gen-2.optical_axis_above_rail} - {sig-romeo-msr-gen-2.axis_above_base}","via":"harvest"},"note":"1.41 in less the ROMEO-MSR's 0.597 in."}],"note":"SIG gives the riser's height only as the ROMEO-MSR's axis on it: \"SIGHT HEIGHT 1.41\" ABSOLUTE CO-WITNESS\" (its sheet). Less the sight's own axis over its base it is the deck's height; another Micro-footprint dot on it stands as much higher or lower as its own axis is over its base (D101). Read directly on the same side view it is the seam's 1.058 in over the clamp's bottom less the clamp's 0.245 under the rail, 0.813: the same figure, since the sight's axis over its base was read there too."},"deck_x":{"label":"The footprint's middle along the riser's top, ahead of the clamp's middle","kind":"length","measurements":[{"id":"side","value":0,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sig-romeo-msr-gen-2 befa92096e57 (Primary Arms SORMSR101_02, the sight on its riser, straight left side on white, 2200 x 1467, objective to the left)","scaleRef":"the sheet's length, 69.7 mm = 1403 px (511.3 px/in), and its height, 62.9 mm = 1274 px (514.5 px/in), which agree within 0.6%: 512.9 px/in","method":"the housing's flat base and the riser's top are one length over one another (their front corners at column 665, their rear ones at 1675), and the clamp's middle, which the frame's origin is, is theirs. No view on file shows the screws that hold the sight to the riser: the footprint's middle is taken to be the base's","via":"harvest"}}]},"mount_length":{"label":"The riser's length along the rail (its clamp's, and its top's, which is as long)","kind":"length","measurements":[{"id":"side","value":1.973,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{sig-romeo-msr-gen-2.mount_length}","via":"harvest"},"note":"Read on Primary Arms' side view of the pair, in the sight's ledger."}]},"clamp_below_rail":{"label":"The riser clamp's bottom below the rail's top","kind":"length","measurements":[{"id":"side","value":0.245,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{sig-romeo-msr-gen-2.clamp_below_rail}","via":"harvest"}}]},"weight":{"label":"Weight (the riser, its clamp plate and its cross bolt)","kind":"mass","measurements":[{"id":"metal","value":1.8,"unit":"oz","pm":0.36,"source":{"type":"derived","basis":"The model's volume, 1.1494 cubic inches, as aluminium (std.density.aluminium, 0.098 lb a cubic inch: 1.802 oz), from pipeline/blender/sig_romeo_msr_gen_2.py's manifest for this part. The ± is a fifth: the clamp plate and the cross bolt aren't modelled, and the four slots in the base aren't cut."}}],"note":"SIG gives no weight for the riser. Weighed by its metal as modelled (CLAUDE.md: a piece no page gives a weight for): its model leaves out the clamp plate, the cross bolt and the four slots in its base, so the ± is a fifth. The sight alone is the sheet's 5.7 oz less this (sig-romeo-msr-gen-2.sight_weight)."}}},{"subject":"sig-romeo5-gen-ii","title":"SIG Sauer ROMEO5 GEN II 1x20mm compact illuminated dot sight, 2 MOA red dot (the sight), with the readings of SIG's drawings of it on the M1913 I-BEAM mount it is sold on (SOR5101)","dimensions":{"length":{"label":"Overall length (the front hood's face to the rear bezel's face)","kind":"length","measurements":[{"id":"manual","value":69.7,"unit":"mm","stated":"Length A: 2.7 in / 69.7 mm","source":{"type":"spec","publisher":"manufacturer","name":"SIG SAUER, ROMEO5 GEN II 1x20 mm compact illuminated dot sight operator's manual (P/N 7405035-01 REV 00, (c)2024), the PDF as Chattanooga Shooting Supply hosts it; its text layer","url":"https://media.chattanoogashooting.com/documents/product/XISORJ5101/Sig%20Sauer%20Romeo5%20GEN%20II%20Operator%20Manual.pdf","retrieved":"2026-10-19","via":"harvest"}},{"id":"sportsmans","value":2.74,"unit":"in","stated":"Length 2.74in","source":{"type":"spec","publisher":"retailer","name":"Sportsman's Warehouse, Sig Sauer Romeo5 Gen II 1x Red Dot - 2 MOA Dot (ID 1900437, MPN SOR5101), specifications","url":"https://www.sportsmans.com/hunting-gear-supplies/optics-binoculars-scopes-rangefinders/red-dots/sig-sauer-romeo5-gen-ii-1x-red-dot-2-moa-dot/p/1900437","retrieved":"2026-10-19","via":"harvest"}},{"id":"impact","value":2.7,"unit":"in","pm":0.05,"stated":"Length : 2.70\"","source":{"type":"spec","publisher":"retailer","name":"Impact Guns, Sig Sauer Romeo 5 Gen II Red Dot Sight, 1x20mm, Black, 2 MOA Dot (SOR5101), specifications","url":"https://www.impactguns.com/reflex-sights/sig-sauer-romeo-5-gen-ii-red-dot-sight-1x20mm-black-2-moa-dot-for-picatinny-798681694600-sor5101","retrieved":"2026-10-19","via":"harvest"},"note":"The manual's 2.7 in with a zero written after it: no closer than the manual's own inches."}],"adopt":{"from":"manual","reason":"SIG's own manual, in the unit it gives to three figures; the sellers repeat it in inches."},"note":"A on the manual's side view spans the sight from the front of its hood to the face of its rear bezel; the I-BEAM mount is shorter (mount_length). Sportsman's 2.74 in is the manual's 69.7 mm put in inches; the other sellers print the manual's inch column."},"width":{"label":"Overall width (the battery cap's face, on the right, to the mount base's left side)","kind":"length","measurements":[{"id":"manual","value":39.6,"unit":"mm","stated":"Width B: 1.6 in / 39.6 mm","source":{"type":"spec","publisher":"manufacturer","name":"SIG SAUER, ROMEO5 GEN II 1x20 mm compact illuminated dot sight operator's manual (P/N 7405035-01 REV 00, (c)2024), the PDF as Chattanooga Shooting Supply hosts it; its text layer","url":"https://media.chattanoogashooting.com/documents/product/XISORJ5101/Sig%20Sauer%20Romeo5%20GEN%20II%20Operator%20Manual.pdf","retrieved":"2026-10-19","via":"harvest"}},{"id":"sportsmans","value":1.56,"unit":"in","stated":"Width 1.56in","source":{"type":"spec","publisher":"retailer","name":"Sportsman's Warehouse, Sig Sauer Romeo5 Gen II 1x Red Dot - 2 MOA Dot (ID 1900437, MPN SOR5101), specifications","url":"https://www.sportsmans.com/hunting-gear-supplies/optics-binoculars-scopes-rangefinders/red-dots/sig-sauer-romeo5-gen-ii-1x-red-dot-2-moa-dot/p/1900437","retrieved":"2026-10-19","via":"harvest"}},{"id":"impact","value":1.6,"unit":"in","pm":0.05,"stated":"Width : 1.60\"","source":{"type":"spec","publisher":"retailer","name":"Impact Guns, Sig Sauer Romeo 5 Gen II Red Dot Sight, 1x20mm, Black, 2 MOA Dot (SOR5101), specifications","url":"https://www.impactguns.com/reflex-sights/sig-sauer-romeo-5-gen-ii-red-dot-sight-1x20mm-black-2-moa-dot-for-picatinny-798681694600-sor5101","retrieved":"2026-10-19","via":"harvest"},"note":"The manual's 1.6 in with a zero written after it."}],"adopt":{"from":"manual","reason":"SIG's own manual, in the unit it gives to three figures; the sellers repeat it in inches."},"note":"B on the manual's front view spans from the battery cap's domed face (the sight's right) to the I-BEAM base's left side, which stands as far out as the housing's left flank."},"height":{"label":"Overall height (the I-BEAM base's foot to the top of the housing's raised deck)","kind":"length","measurements":[{"id":"manual","value":61.5,"unit":"mm","stated":"Height C (Standard & Elite Models): 2.4 in / 61.5 mm","source":{"type":"spec","publisher":"manufacturer","name":"SIG SAUER, ROMEO5 GEN II 1x20 mm compact illuminated dot sight operator's manual (P/N 7405035-01 REV 00, (c)2024), the PDF as Chattanooga Shooting Supply hosts it; its text layer","url":"https://media.chattanoogashooting.com/documents/product/XISORJ5101/Sig%20Sauer%20Romeo5%20GEN%20II%20Operator%20Manual.pdf","retrieved":"2026-10-19","via":"harvest"}},{"id":"sportsmans","value":2.42,"unit":"in","stated":"Height 2.42in","source":{"type":"spec","publisher":"retailer","name":"Sportsman's Warehouse, Sig Sauer Romeo5 Gen II 1x Red Dot - 2 MOA Dot (ID 1900437, MPN SOR5101), specifications","url":"https://www.sportsmans.com/hunting-gear-supplies/optics-binoculars-scopes-rangefinders/red-dots/sig-sauer-romeo5-gen-ii-1x-red-dot-2-moa-dot/p/1900437","retrieved":"2026-10-19","via":"harvest"}},{"id":"impact","value":2.4,"unit":"in","pm":0.05,"stated":"Height : 2.40\"","source":{"type":"spec","publisher":"retailer","name":"Impact Guns, Sig Sauer Romeo 5 Gen II Red Dot Sight, 1x20mm, Black, 2 MOA Dot (SOR5101), specifications","url":"https://www.impactguns.com/reflex-sights/sig-sauer-romeo-5-gen-ii-red-dot-sight-1x20mm-black-2-moa-dot-for-picatinny-798681694600-sor5101","retrieved":"2026-10-19","via":"harvest"},"note":"The manual's 2.4 in with a zero written after it."},{"id":"drawing","value":2.486,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii eb04cdd95d59 (SIG's operator's manual, page 2, rendered at 600 dpi and cropped: the dimensioned right side view and front view of the sight on its I-BEAM mount, and the view from below)","scaleRef":"the side view at the scale of its A: 69.7 mm = 1149 px (532 to 1681), 418.7 px/in","method":"the side view's outline from the base's foot (row 3474) to the deck's top (row 2431): 1043 px; the front view's, 1041 px at its own B scale (2.474 in): the ± covers both and the half-percent between the two scales","via":"harvest"}},{"id":"pa-left","value":2.488,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii 598b3527908a (Primary Arms SOR5101_02, a straight left side view on white, 2200 x 1467)","scaleRef":"the manual's length, 69.7 mm, over the outline's length (tools/trace.py, the seed's check pa-left)","method":"the traced outline's height, from the clamp jaw's foot to the deck's top","via":"harvest"},"note":"A photograph at the drawing's scale: its outline matches the drawing's (IoU 0.966). Its foot is the jaw's, which stands nearer the lens than the base and shows a few hundredths lower than the base's sides beside it: the ± covers that. It has the sight the drawing's height, not the printed C's."}],"adopt":{"from":"drawing","reason":"The manual's drawing at the scale its own A and B agree on, which also puts the axis at the manual's 1.41 in, and a photograph of the sight at the same length agrees with it: the model is built from that drawing, and the printed C is 1.6 mm under it."},"note":"C on the manual's front view runs from the I-BEAM base's foot to the top of the raised deck the buttons are on. The manual's own drawings, at the one scale their A and B give, are 63.1 mm high (1041 px on the front view, 1043 on the side view): 2.6% over the C printed beside them, while they put the axis where the manual's 1.41 in says within 0.2%. The model is the drawing, so its height is the drawing's (adopted); the printed C is kept. The manual's Tall model figures don't settle it: its C grows by 9.2 mm (to 70.7) where its axis grows by 13.2 (to 1.93 in), so the printed heights don't follow the axis heights either way."},"optical_axis_above_rail":{"label":"Optical axis above the rail's top (on the I-BEAM mount)","kind":"length","measurements":[{"id":"manual","value":1.41,"unit":"in","stated":"Sight to Optical Axis: 1.41” (Standard Models & Elite), 1.93” (Tall Models)","source":{"type":"spec","publisher":"manufacturer","name":"SIG SAUER, ROMEO5 GEN II 1x20 mm compact illuminated dot sight operator's manual (P/N 7405035-01 REV 00, (c)2024), the PDF as Chattanooga Shooting Supply hosts it; its text layer","url":"https://media.chattanoogashooting.com/documents/product/XISORJ5101/Sig%20Sauer%20Romeo5%20GEN%20II%20Operator%20Manual.pdf","retrieved":"2026-10-19","via":"harvest"}},{"id":"vyce","value":1.41,"unit":"in","stated":"Both sit at 1.41” and provide an absolute co-witness with iron sights.","source":{"type":"spec","publisher":"review","name":"Vyce Outdoor, Sig Sauer ROMEO5 Gen 1 vs Gen 2 - Comparison & Review","url":"https://www.vyceoutdoor.com/scopes-and-optics/romeo5-gen2","retrieved":"2026-10-19","via":"harvest"},"note":"The reviewer's sentence of the GEN II and the GEN II Elite on this mount, not a measurement."},{"id":"bereli","value":1.41,"unit":"in","stated":"Sight Height: 1.41\" Absolute Co-Witness","source":{"type":"spec","publisher":"retailer","name":"Bereli, SIG SAUER ROMEO5 GEN II Elite 1x20mm w/ 1.41in Absolute Co-Witness Mount (SOR5105, the Elite: the same housing and mount with another reticle)","url":"https://www.bereli.com/sor5105/","retrieved":"2026-10-19","via":"harvest"},"note":"The Elite's page (SOR5105): the same housing on the same mount."}],"adopt":{"from":"manual","reason":"SIG's own manual; a reviewer and a seller of the Elite repeat it."},"note":"The manual's \"Sight to Optical Axis\": the rail's top to the optical axis, the figure an AR's co-witness is read by (Vyce Outdoor and Bereli both call 1.41 in absolute co-witness). The manual's front view, at the scale of its B, has the objective's rings centred 591 px over the roof of the base's rail channel, 1.404 in."},"weight":{"label":"Weight (the manual's figure for the standard model; it doesn't say whether the mount or the battery is in it)","kind":"mass","measurements":[{"id":"manual","value":155,"unit":"g","stated":"Weight (Standard &Elite Models): 5.5 oz / 155 g","source":{"type":"spec","publisher":"manufacturer","name":"SIG SAUER, ROMEO5 GEN II 1x20 mm compact illuminated dot sight operator's manual (P/N 7405035-01 REV 00, (c)2024), the PDF as Chattanooga Shooting Supply hosts it; its text layer","url":"https://media.chattanoogashooting.com/documents/product/XISORJ5101/Sig%20Sauer%20Romeo5%20GEN%20II%20Operator%20Manual.pdf","retrieved":"2026-10-19","via":"harvest"}},{"id":"sportsmans","value":5.5,"unit":"oz","stated":"Weight 5.5oz","source":{"type":"spec","publisher":"retailer","name":"Sportsman's Warehouse, Sig Sauer Romeo5 Gen II 1x Red Dot - 2 MOA Dot (ID 1900437, MPN SOR5101), specifications","url":"https://www.sportsmans.com/hunting-gear-supplies/optics-binoculars-scopes-rangefinders/red-dots/sig-sauer-romeo5-gen-ii-1x-red-dot-2-moa-dot/p/1900437","retrieved":"2026-10-19","via":"harvest"}},{"id":"impact","value":5.5,"unit":"oz","pm":0.05,"stated":"Weight : 5.50 oz","source":{"type":"spec","publisher":"retailer","name":"Impact Guns, Sig Sauer Romeo 5 Gen II Red Dot Sight, 1x20mm, Black, 2 MOA Dot (SOR5101), specifications","url":"https://www.impactguns.com/reflex-sights/sig-sauer-romeo-5-gen-ii-red-dot-sight-1x20mm-black-2-moa-dot-for-picatinny-798681694600-sor5101","retrieved":"2026-10-19","via":"harvest"},"note":"The manual's 5.5 oz with a zero written after it."},{"id":"bereli","value":5.5,"unit":"oz","stated":"Weight: 5.5 oz (without battery)","source":{"type":"spec","publisher":"retailer","name":"Bereli, SIG SAUER ROMEO5 GEN II Elite 1x20mm w/ 1.41in Absolute Co-Witness Mount (SOR5105, the Elite: the same housing and mount with another reticle)","url":"https://www.bereli.com/sor5105/","retrieved":"2026-10-19","via":"harvest"},"note":"The Elite's page."}],"adopt":{"from":"manual","reason":"SIG's own manual, in grams; the sellers repeat its ounces."},"note":"The manual gives one weight for the standard and Elite models and 4 g more for the Tall model, whose only difference is its taller mount: so the figure is taken to be the sight on its I-BEAM mount (an inference, said as one). Bereli, of the Elite, says it is without the battery. The model's volume as solid aluminium is held against it in the part's test."},"axis_above_base":{"label":"Optical axis above the sight's own base (the plane its footprint meets a mount's deck in: D101)","kind":"length","measurements":[{"id":"drawing","value":0.612,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii eb04cdd95d59 (SIG's operator's manual, page 2, rendered at 600 dpi and cropped: the dimensioned right side view and front view of the sight on its I-BEAM mount, and the view from below)","scaleRef":"the side view at the scale of its A: 69.7 mm = 1149 px (532 to 1681), 418.7 px/in","method":"the skirt's foot in the traced side view (profiles.side, feature skirt: the housing's seam with the top plate), 0.798 in over the rail's top as the outline is placed, to the axis at the manual's 1.41 in: the ± is the line's width and the half-percent between the drawing's two scales","via":"harvest"}}],"note":"What the sight brings to any Micro-footprint mount (D101): its axis this far over the deck it is screwed to. On the manual's side view the housing's skirt comes down onto the I-BEAM's top plate in one straight line, the seam the four mounting screws come up through from below (\"Mounting Screws (F)\"); on the I-BEAM it puts the axis at the manual's 1.41 in, which is what the mount's deck height is worked out from (sig-romeo5-i-beam-mount.deck_above_rail)."},"sight_weight":{"label":"Weight of the sight alone (off its I-BEAM mount)","kind":"mass","measurements":[{"id":"manual-less-mount","value":96.4,"unit":"g","pm":6,"source":{"type":"derived","expr":"{.weight} - {sig-romeo5-i-beam-mount.weight}","via":"harvest"},"note":"155 g less 58.6 g."}],"note":"SIG gives one weight, the sight on its I-BEAM (weight: taken to be that, as the note there says). The sight alone is that less the mount, whose weight is its metal (sig-romeo5-i-beam-mount.weight): the two add up to the manual's figure, so a build's weight doesn't move with the split (D101)."},"window_d":{"label":"Clear aperture","kind":"length","measurements":[{"id":"manual","value":20,"unit":"mm","stated":"Clear aperture: 20 mm","source":{"type":"spec","publisher":"manufacturer","name":"SIG SAUER, ROMEO5 GEN II 1x20 mm compact illuminated dot sight operator's manual (P/N 7405035-01 REV 00, (c)2024), the PDF as Chattanooga Shooting Supply hosts it; its text layer","url":"https://media.chattanoogashooting.com/documents/product/XISORJ5101/Sig%20Sauer%20Romeo5%20GEN%20II%20Operator%20Manual.pdf","retrieved":"2026-10-19","via":"harvest"}}],"note":"Draws the lens at both ends. The manual's front view has the objective's glass 0.81 in across at the scale of its B (342 px), the 20 mm within 3%."},"mount_length":{"label":"The I-BEAM mount's length along the rail (its base, and its top plate, which is as long)","kind":"length","measurements":[{"id":"drawing","value":1.98,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii eb04cdd95d59 (SIG's operator's manual, page 2 at 600 dpi: the dimensioned right side view (A) of the sight on its I-BEAM mount, line art)","scaleRef":"scale from sig-romeo5-gen-ii.length = 2.74409 in (x-extent 1146 px → 417.6 px/in)","method":"median row width in y [0.02, 0.15] (1.980–1.980) of the traced outline (tools/trace.py); the I-BEAM base's length along its lowest rows, on the manual's side view at the scale of its A","via":"harvest"}}]},"tube_od":{"label":"The front hood's diameter at its face","kind":"length","measurements":[{"id":"side","value":1.123,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii eb04cdd95d59 (SIG's operator's manual, page 2, rendered at 600 dpi and cropped: the dimensioned right side view and front view of the sight on its I-BEAM mount, and the view from below)","scaleRef":"the side view at the scale of its A as the trace has it, 417.6 px/in","method":"the outline at the hood's face (column 1681) from row 2553 to row 3022: 469 px","via":"harvest"}},{"id":"top","value":1.12,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii 4e1e08214612 (SIG's view from above as AR15Discounts shows it, 1000 x 700)","scaleRef":"the manual's length, 69.7 mm = 576 px, 8.26 px/mm","method":"the hood across at its face (columns 397 to 632): 235 px","via":"harvest"}}],"adopt":{"from":"side","reason":"The maker's drawing, square on; SIG's photo from above agrees within 0.3%."},"note":"Its rim at the face: the side view's outline at its front from the top to the bottom, and SIG's view from above across it. Toward its seam with the housing it grows a little (the side outline's top rises 12 px over its length), which the model follows."},"axis_above_clamp_bottom":{"label":"Optical axis above the I-BEAM base's foot","kind":"length","measurements":[{"id":"side","value":1.645,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii eb04cdd95d59 (SIG's operator's manual, page 2, rendered at 600 dpi and cropped: the dimensioned right side view and front view of the sight on its I-BEAM mount, and the view from below)","scaleRef":"the side view at the scale of its A as the trace has it: 69.7 mm = 1146 px inside the stroke, 417.6 px/in","method":"the axis row (2787: the battery cap's and the windage turret's centres) to the base's foot (row 3474): 687 px","via":"harvest"}},{"id":"front","value":1.626,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii eb04cdd95d59 (SIG's operator's manual, page 2, rendered at 600 dpi and cropped: the dimensioned right side view and front view of the sight on its I-BEAM mount, and the view from below)","scaleRef":"the front view at the scale of its B: 39.6 mm = 656 px (2111 to 2767), 420.8 px/in; its A and B agree within 0.5%","method":"the axis row (2787: the objective's rings' centre) to the base's foot (row 3471): 684 px","via":"harvest"}}],"adopt":{"from":"side","reason":"The outline the sight is built from, and every place along it, are the side view's: the axis is where that view has it."},"note":"On the manual's drawing the battery cap's circle, the windage turret's rings (side view) and the objective's rings (front view) share one centre row, 2787: the axis. The two views put it 0.019 in apart above the foot (their feet are 3 px apart and their scales 0.5%): the side view's is adopted, since the sight's outline and every place along it are that view's; the model fits the front view's outline to the side view's height (geometry.approximations)."},"clamp_below_rail":{"label":"The I-BEAM base's foot below the rail's top","kind":"length","measurements":[{"id":"derived","value":0.235,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{.axis_above_clamp_bottom} - {.optical_axis_above_rail}","via":"harvest"},"note":"The drawing's own front view has its foot 93 px (0.221 in) under the roof of the base's rail channel, and the cross bolt's head centred on that roof in the side view: the 0.014 in between the two is the drawing's axis at 1.404 in over that roof where the manual says 1.41."}]},"clamp_bottom_y":{"label":"The I-BEAM base's foot in the optic frame (y; the rail's top is 0)","kind":"length","measurements":[{"id":"derived","value":-0.235,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"-{.clamp_below_rail}","via":"harvest"},"note":"Where the traced outlines' foot origin sits in the part frame, so the axis lands at the manual's 1.41 in."}]},"cap_face_z":{"label":"The battery cap's domed face, out from the axis on the sight's right","kind":"length","measurements":[{"id":"front","value":0.91,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii eb04cdd95d59 (SIG's operator's manual, page 2, rendered at 600 dpi and cropped: the dimensioned right side view and front view of the sight on its I-BEAM mount, and the view from below)","scaleRef":"the front view at the scale of its B: 39.6 mm = 656 px (2111 to 2767), 420.8 px/in; its A and B agree within 0.5%","method":"the front view's outline at the cap's face (column 2111) from the axis's column (2494, the objective's rings' centre and the web's middle): 383 px","via":"harvest"},"note":"The left end of B: with base_left_z it makes the manual's 39.6 mm."}]},"cap_rim_z":{"label":"Where the battery cap meets its boss, out from the axis","kind":"length","measurements":[{"id":"front","value":0.791,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii eb04cdd95d59 (SIG's operator's manual, page 2, rendered at 600 dpi and cropped: the dimensioned right side view and front view of the sight on its I-BEAM mount, and the view from below)","scaleRef":"the front view at the scale of its B: 39.6 mm = 656 px (2111 to 2767), 420.8 px/in; its A and B agree within 0.5%","method":"the front view's line round the cap where its rim meets the boss it screws into (column 2161): 333 px from the axis's column","via":"harvest"},"note":"From there out the cap's knurled rim and its domed face (to cap_face_z)."}]},"flank_z":{"label":"The housing's flank, out from the axis (each side)","kind":"length","measurements":[{"id":"front","value":0.637,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii eb04cdd95d59 (SIG's operator's manual, page 2, rendered at 600 dpi and cropped: the dimensioned right side view and front view of the sight on its I-BEAM mount, and the view from below)","scaleRef":"the front view at the scale of its B: 39.6 mm = 656 px (2111 to 2767), 420.8 px/in; its A and B agree within 0.5%","method":"the front view's outline along the housing's left flank (its ribs, column 2762; the sight's left is the drawing's right): 268 px from the axis's column","via":"harvest"}},{"id":"top","value":0.618,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii 4e1e08214612 (SIG's view from above as AR15Discounts shows it, 1000 x 700)","scaleRef":"the manual's length, 69.7 mm = 576 px from the hood's face (row 77) to the rear bezel's (row 653), 8.26 px/mm","method":"the left flank's edge (column 385) from the hood's middle (column 514.5, the hood 397 to 632): 129.5 px","via":"harvest"},"note":"A photo from above at a studio's distance: the flank, lower than the hood's top, reads a little small."}],"adopt":{"from":"front","reason":"The maker's drawing, square on."},"note":"The housing is taken as symmetric about the axis under its battery cap and windage turret, which only its right side carries: the right flank isn't seen square in any view on file (the cap hides it from the front, and from above it is a few hundredths in from the left)."},"base_left_z":{"label":"The I-BEAM base's left side (the clamp jaw's face), out from the axis","kind":"length","measurements":[{"id":"front","value":0.649,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii eb04cdd95d59 (SIG's operator's manual, page 2, rendered at 600 dpi and cropped: the dimensioned right side view and front view of the sight on its I-BEAM mount, and the view from below)","scaleRef":"the front view at the scale of its B: 39.6 mm = 656 px (2111 to 2767), 420.8 px/in; its A and B agree within 0.5%","method":"the right end of B on the front view (column 2767): 273 px from the axis's column","via":"harvest"}}]},"jaw_inner_z":{"label":"The line that parts the clamp jaw from the base, out from the axis on the left","kind":"length","measurements":[{"id":"front","value":0.442,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii eb04cdd95d59 (SIG's operator's manual, page 2, rendered at 600 dpi and cropped: the dimensioned right side view and front view of the sight on its I-BEAM mount, and the view from below)","scaleRef":"the front view at the scale of its B: 39.6 mm = 656 px (2111 to 2767), 420.8 px/in; its A and B agree within 0.5%","method":"the front view's upright line through the base's left side under the channel's hook (column 2680): 186 px from the axis's column","via":"harvest"},"note":"Read as the jaw's inner face, where the separate clamp bar meets the base: the left photo (Primary Arms SOR5101_02) shows the jaw as a block of its own at the base's middle."}]},"jaw_length":{"label":"The clamp jaw's length along the rail","kind":"length","measurements":[{"id":"left","value":0.714,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii 598b3527908a (Primary Arms SOR5101_02, a straight left side view on white, 2200 x 1467)","scaleRef":"the base's length, mount_length (1.98 in) = 886 px (columns 660 to 1546), 447 px/in","method":"the jaw block's front and rear edges on the base's left side (columns 935 and 1254): 319 px; centred 0.02 in ahead of the base's middle, inside what a reading off the displayed photo leaves: drawn centred on it","via":"harvest"}}]},"web_width":{"label":"The I-BEAM's web across, where it is narrowest","kind":"length","measurements":[{"id":"front","value":0.228,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii eb04cdd95d59 (SIG's operator's manual, page 2, rendered at 600 dpi and cropped: the dimensioned right side view and front view of the sight on its I-BEAM mount, and the view from below)","scaleRef":"the front view at the scale of its B: 39.6 mm = 656 px (2111 to 2767), 420.8 px/in; its A and B agree within 0.5%","method":"the front view's web between its two concave sides at rows 3132 to 3163 (columns 2446 to 2542): 96 px, centred on the axis's column","via":"harvest"}}]},"screw_z":{"label":"The mounting screws' heads under the top plate, out from the axis (each side)","kind":"length","measurements":[{"id":"front","value":0.2,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii eb04cdd95d59 (SIG's operator's manual, page 2, rendered at 600 dpi and cropped: the dimensioned right side view and front view of the sight on its I-BEAM mount, and the view from below)","scaleRef":"the front view at the scale of its B: 39.6 mm = 656 px (2111 to 2767), 420.8 px/in; its A and B agree within 0.5%","method":"the two heads' centres on the front view (columns 2410 and 2578), 84 px either side of the axis's column","via":"harvest"}}],"note":"Four T10 screws (F) hold the sight to the I-BEAM's top plate from below (the manual's view from below): two each side of the web, at the two ends of the plate."},"screw_head_d":{"label":"A mounting screw's head across","kind":"length","measurements":[{"id":"front","value":0.214,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii eb04cdd95d59 (SIG's operator's manual, page 2, rendered at 600 dpi and cropped: the dimensioned right side view and front view of the sight on its I-BEAM mount, and the view from below)","scaleRef":"the front view at the scale of its B: 39.6 mm = 656 px (2111 to 2767), 420.8 px/in; its A and B agree within 0.5%","method":"each head's width on the front view (2365 to 2455, 2533 to 2623): 90 px","via":"harvest"},"note":"The side view's features (screw_rear, screw_front) are 92 px across at its own scale: the same."}]},"button_width":{"label":"A button's width across the deck","kind":"length","measurements":[{"id":"front","value":0.25,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii eb04cdd95d59 (SIG's operator's manual, page 2, rendered at 600 dpi and cropped: the dimensioned right side view and front view of the sight on its I-BEAM mount, and the view from below)","scaleRef":"the front view at the scale of its B: 39.6 mm = 656 px (2111 to 2767), 420.8 px/in; its A and B agree within 0.5%","method":"the two buttons seen from the front (columns 2443 to 2548): 105 px, centred on the axis","via":"harvest"}}]},"lug_width":{"label":"The block under the channel's roof that stands in a rail's slot: its width across","kind":"length","measurements":[{"id":"front","value":0.314,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii eb04cdd95d59 (SIG's operator's manual, page 2, rendered at 600 dpi and cropped: the dimensioned right side view and front view of the sight on its I-BEAM mount, and the view from below)","scaleRef":"the front view at the scale of its B: 39.6 mm = 656 px (2111 to 2767), 420.8 px/in; its A and B agree within 0.5%","method":"the front view's rectangle under the channel's roof (columns 2428 to 2560): 132 px, centred on the axis's column","via":"harvest"},"note":"Where along the base it is isn't drawn: it is taken to be under the cross bolt, at the base's middle, as the manual's \"push the sight forward into the rail lugs\" and the bolt's place say."}]},"lug_depth":{"label":"How far that block stands under the channel's roof","kind":"length","measurements":[{"id":"front","value":0.1,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii eb04cdd95d59 (SIG's operator's manual, page 2, rendered at 600 dpi and cropped: the dimensioned right side view and front view of the sight on its I-BEAM mount, and the view from below)","scaleRef":"the front view at the scale of its B: 39.6 mm = 656 px (2111 to 2767), 420.8 px/in; its A and B agree within 0.5%","method":"the front view's rectangle from the channel's roof (row 3378) to its lower edge (row 3420): 42 px","via":"harvest"},"note":"Inside a rail slot's depth (std.picatinny.slot_depth)."}]},"lug_length":{"label":"That block's length along the rail","kind":"length","measurements":[{"id":"assumed","value":0.15,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows the block from the side. Taken as a little less than a rail slot's width (0.206 in), so it lies in one.","via":"harvest"}}],"note":"No view on file shows it from the side (the base hides it)."},"elevation_from_rear":{"label":"The elevation turret's centre, ahead of the rear bezel's face","kind":"length","measurements":[{"id":"top","value":0.61,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii 4e1e08214612 (SIG's view from above as AR15Discounts shows it, 1000 x 700)","scaleRef":"the manual's length, 69.7 mm = 576 px from the hood's face (row 77) to the rear bezel's (row 653), 8.26 px/mm","method":"the dial's centre (row 525) from the rear bezel's face: 128 px","via":"harvest"},"note":"The windage turret's centre is 0.670 in ahead of the rear face on the manual's side view (the side view's feature windage_cap): the two turrets are 0.06 in apart along the sight, within what a photo from above leaves; the drawing shows the elevation turret's housing between columns 700 and 920 of its top, centred 0.67 in ahead of the rear face."}]},"elevation_d":{"label":"The elevation turret's dial across","kind":"length","measurements":[{"id":"top","value":0.601,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii 4e1e08214612 (SIG's view from above as AR15Discounts shows it, 1000 x 700)","scaleRef":"the manual's length, 69.7 mm = 576 px, 8.26 px/mm","method":"the dial's outer ring (columns 452 to 578): 126 px","via":"harvest"},"note":"Its top is flush with the deck in the side view: the dial is drawn as a ring cut round it."}]},"windage_face_z":{"label":"The windage turret's face, out from the axis on the sight's right","kind":"length","measurements":[{"id":"top","value":0.827,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii 4e1e08214612 (SIG's view from above as AR15Discounts shows it, 1000 x 700)","scaleRef":"the manual's length, 69.7 mm = 576 px, 8.26 px/mm","method":"the turret's block on the right side behind the battery cap (column 688, rows 440 to 590) from the hood's middle (column 514.5): 173.5 px","via":"harvest"},"note":"The only view of its reach: the cap hides it from the front."}]},"hood_length":{"label":"The front hood's length, from its seam with the housing to its face","kind":"length","measurements":[{"id":"side","value":0.247,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii eb04cdd95d59 (SIG's operator's manual, page 2, rendered at 600 dpi and cropped: the dimensioned right side view and front view of the sight on its I-BEAM mount, and the view from below)","scaleRef":"the side view at the scale of its A as the trace has it, 417.6 px/in","method":"the seam line across the sight (column 1578) to the face (1681): 103 px","via":"harvest"}}]},"hood_notch_depth":{"label":"How deep the hood's notches are cut into its rim","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the front view draws the eight notches round the hood's face as pads 0.03 to 0.06 in across, and no view shows how deep they go.","via":"harvest"}}]},"hood_notch_length":{"label":"How far back the hood's notches run from its face","kind":"length","measurements":[{"id":"side","value":0.17,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii eb04cdd95d59 (SIG's operator's manual, page 2, rendered at 600 dpi and cropped: the dimensioned right side view and front view of the sight on its I-BEAM mount, and the view from below)","scaleRef":"the side view at the scale of its A as the trace has it, 417.6 px/in","method":"the notches' rounded rear ends in the side view (column 1610) to the face (1681): 71 px","via":"harvest"}}]},"cap_edge_z":{"label":"The edge of the battery cap's domed face, out from the axis","kind":"length","measurements":[{"id":"front","value":0.841,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii eb04cdd95d59 (SIG's operator's manual, page 2, rendered at 600 dpi and cropped: the dimensioned right side view and front view of the sight on its I-BEAM mount, and the view from below)","scaleRef":"the front view at the scale of its B: 39.6 mm = 656 px (2111 to 2767), 420.8 px/in; its A and B agree within 0.5%","method":"the front view's outline where the cap's face meets its rim at the cap's top and bottom (column 2140): 354 px from the axis's column; the face's middle is cap_face_z","via":"harvest"},"note":"The face is drawn as a sphere's cap through its middle (cap_face_z) and this edge at the cap's radius: a construction from two readings."}]},"objective_bezel_d":{"label":"The ring round the objective inside the hood, across","kind":"length","measurements":[{"id":"front","value":0.94,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii eb04cdd95d59 (SIG's operator's manual, page 2, rendered at 600 dpi and cropped: the dimensioned right side view and front view of the sight on its I-BEAM mount, and the view from below)","scaleRef":"the front view at the scale of its B: 39.6 mm = 656 px (2111 to 2767), 420.8 px/in; its A and B agree within 0.5%","method":"the front view's innermost ring outside the glass (columns 2299 to 2695): 396 px, centred on the axis's column","via":"harvest"}}]},"objective_recess":{"label":"How far the objective's glass sits inside the hood's face","kind":"length","measurements":[{"id":"assumed","value":0.12,"unit":"in","pm":0.06,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the front view shows the rings round the glass and no view shows how deep they go. Taken as half the hood's length.","via":"harvest"}}]},"hood_notch_width":{"label":"A hood notch's width round the rim","kind":"length","measurements":[{"id":"front","value":0.128,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii eb04cdd95d59 (SIG's operator's manual, page 2, rendered at 600 dpi and cropped: the dimensioned right side view and front view of the sight on its I-BEAM mount, and the view from below)","scaleRef":"the front view at the scale of its B: 39.6 mm = 656 px (2111 to 2767), 420.8 px/in; its A and B agree within 0.5%","method":"the eight pads round the hood's face in the front view, the one at the top and the one at the bottom square on (columns 2416 to 2470): 54 px","via":"harvest"}}]},"windage_step":{"label":"How far the windage turret's cap stands out of its boss, and its dial out of the cap","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the side view draws the boss, the cap and the dial as three rings and the view from above has only the whole turret's reach (windage_face_z).","via":"harvest"}}]},"turret_groove":{"label":"The groove round the elevation turret's dial in the deck: its width and its depth","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: SIG's view from above shows a dark ring round the dial and the side view has the dial flush with the deck.","via":"harvest"}}]},"bolt_counterbore":{"label":"How deep the cross bolt's head sits in the base's right side","kind":"length","measurements":[{"id":"assumed","value":0.05,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the side view draws the head inside a ring (torx_head's outer circle) and the front view has nothing standing out of the base's right side there.","via":"harvest"}}]},"torx_star_d":{"label":"The cross bolt's T20 star recess across its points","kind":"length","measurements":[{"id":"side","value":0.165,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii eb04cdd95d59 (SIG's operator's manual, page 2, rendered at 600 dpi and cropped: the dimensioned right side view and front view of the sight on its I-BEAM mount, and the view from below)","scaleRef":"the side view at the scale of its A as the trace has it, 417.6 px/in","method":"the six-pointed recess in the bolt's head (columns 1022 to 1091): 69 px","via":"harvest"}}]},"torx_depth":{"label":"How deep the star recess is cut","kind":"length","measurements":[{"id":"assumed","value":0.04,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view looks into it.","via":"harvest"}}]},"bolt_end_d":{"label":"The cross bolt's round end on the clamp jaw (the sight's left), across","kind":"length","measurements":[{"id":"left","value":0.197,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii 598b3527908a (Primary Arms SOR5101_02, a straight left side view on white, 2200 x 1467)","scaleRef":"the base's length, mount_length (1.98 in) = 886 px (columns 660 to 1546), 447 px/in","method":"the round end at the jaw's middle (columns 1122 to 1210): 88 px","via":"harvest"}}]},"bolt_end_proud":{"label":"How far the bolt's round end stands out of the jaw","kind":"length","measurements":[{"id":"assumed","value":0.015,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the left photo shows it lit as a low dome; the front view has nothing standing out of the jaw's face.","via":"harvest"}}]},"torx_head_d":{"label":"The cross bolt's head across (inside the ring it sits in)","kind":"length","measurements":[{"id":"side","value":0.231,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii eb04cdd95d59 (SIG's operator's manual, page 2, rendered at 600 dpi and cropped: the dimensioned right side view and front view of the sight on its I-BEAM mount, and the view from below)","scaleRef":"the side view at the scale of its A as the trace has it, 417.6 px/in","method":"the inner of the two circles round the star recess (columns 1009.5 to 1106): 96.5 px; the outer (the feature torx_head, 0.289 in) is taken as the counterbore it sits in","via":"harvest"}}]},"windage_slot_length":{"label":"The windage dial's coin slot, its length","kind":"length","measurements":[{"id":"side","value":0.26,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii eb04cdd95d59 (SIG's operator's manual, page 2, rendered at 600 dpi and cropped: the dimensioned right side view and front view of the sight on its I-BEAM mount, and the view from below)","scaleRef":"the side view at the scale of its A as the trace has it, 417.6 px/in","method":"the rounded slot across the dial (columns 759 to 868): 109 px","via":"harvest"}}]},"windage_slot_width":{"label":"The windage dial's coin slot, its width","kind":"length","measurements":[{"id":"side","value":0.096,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii eb04cdd95d59 (SIG's operator's manual, page 2, rendered at 600 dpi and cropped: the dimensioned right side view and front view of the sight on its I-BEAM mount, and the view from below)","scaleRef":"the side view at the scale of its A as the trace has it, 417.6 px/in","method":"the slot's outer outline (rows 2768 to 2808): 40 px","via":"harvest"}}]},"cap_slot_length":{"label":"The battery cap's coin slot, its length","kind":"length","measurements":[{"id":"side","value":0.497,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii eb04cdd95d59 (SIG's operator's manual, page 2, rendered at 600 dpi and cropped: the dimensioned right side view and front view of the sight on its I-BEAM mount, and the view from below)","scaleRef":"the side view at the scale of its A as the trace has it, 417.6 px/in","method":"the rectangle across the cap's face, centred on it (columns 1125.5 to 1333): 207.5 px","via":"harvest"},"note":"The cap screws in, so where its slot ends up turned isn't the part's: SIG's right side photo has it upright, the drawing along the sight, as it is drawn."}]},"cap_slot_width":{"label":"The battery cap's coin slot, its width","kind":"length","measurements":[{"id":"side","value":0.127,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii eb04cdd95d59 (SIG's operator's manual, page 2, rendered at 600 dpi and cropped: the dimensioned right side view and front view of the sight on its I-BEAM mount, and the view from below)","scaleRef":"the side view at the scale of its A as the trace has it, 417.6 px/in","method":"the rectangle's height (rows 2761 to 2814): 53 px","via":"harvest"}}]},"coin_slot_depth":{"label":"How deep the three coin slots (the battery cap's and the two turrets' dials) are cut","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view looks into a slot.","via":"harvest"}}]},"elevation_slot_length":{"label":"The elevation dial's coin slot, its length (across the sight)","kind":"length","measurements":[{"id":"top","value":0.29,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii 4e1e08214612 (SIG's view from above as AR15Discounts shows it, 1000 x 700)","scaleRef":"the manual's length, 69.7 mm = 576 px, 8.26 px/mm","method":"the slot in the dial's middle (columns 485.5 to 546): 61 px","via":"harvest"}}]},"elevation_slot_width":{"label":"The elevation dial's coin slot, its width","kind":"length","measurements":[{"id":"top","value":0.11,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii 4e1e08214612 (SIG's view from above as AR15Discounts shows it, 1000 x 700)","scaleRef":"the manual's length, 69.7 mm = 576 px, 8.26 px/mm","method":"the slot's width along the sight (rows 521.5 to 544): 22.5 px","via":"harvest"}}]},"panel_length":{"label":"The panel the two buttons are in, along the deck","kind":"length","measurements":[{"id":"top","value":1.177,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii 4e1e08214612 (SIG's view from above as AR15Discounts shows it, 1000 x 700)","scaleRef":"the manual's length, 69.7 mm = 576 px, 8.26 px/mm","method":"the rounded panel's outline round the buttons (rows 200 to 447): 247 px, as seen from above (the deck slopes at 10 degrees: its own length 1.5% more)","via":"harvest"}}]},"panel_width":{"label":"The panel the two buttons are in, across","kind":"length","measurements":[{"id":"top","value":0.505,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii 4e1e08214612 (SIG's view from above as AR15Discounts shows it, 1000 x 700)","scaleRef":"the manual's length, 69.7 mm = 576 px, 8.26 px/mm","method":"the rounded panel's outline (columns 462 to 568): 106 px, centred on the hood's middle","via":"harvest"}}]},"panel_from_front":{"label":"The panel's front end, behind the hood's face","kind":"length","measurements":[{"id":"top","value":0.587,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii 4e1e08214612 (SIG's view from above as AR15Discounts shows it, 1000 x 700)","scaleRef":"the manual's length, 69.7 mm = 576 px, 8.26 px/mm","method":"the panel's front edge (row 200) from the hood's face (row 77): 123 px","via":"harvest"},"note":"The buttons the side view draws lie inside it, 0.05 in and more from its ends."}]},"panel_groove":{"label":"The groove round the buttons' panel: its width and its depth","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: SIG's view from above shows a dark line round the panel and the side view nothing of its depth.","via":"harvest"}}]}}},{"subject":"sig-romeo5-i-beam-mount","title":"SIG Sauer M1913 I-BEAM mount, absolute co-witness (1.41 in), the mount the ROMEO5 GEN II is sold on","dimensions":{"deck_above_rail":{"label":"The top plate's top (where a dot's base sits) above the rail's top","kind":"length","measurements":[{"id":"manual-less-romeo5","value":0.798,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{sig-romeo5-gen-ii.optical_axis_above_rail} - {sig-romeo5-gen-ii.axis_above_base}","via":"harvest"},"note":"1.41 in less the ROMEO5's 0.612 in."}],"note":"SIG gives the mount's height only as the ROMEO5's axis on it: \"Sight to Optical Axis: 1.41” (Standard Models & Elite)\" (the manual). Less the ROMEO5's own axis over its base it is the deck's height; another Micro-footprint dot on it stands as much higher or lower as its own axis is over its base (D101)."},"deck_x":{"label":"The footprint's middle along the top plate, ahead of the base's middle","kind":"length","measurements":[{"id":"drawing","value":0,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/sig-romeo5-gen-ii eb04cdd95d59 (SIG's operator's manual, page 2, rendered at 600 dpi and cropped: the dimensioned right side view and front view of the sight on its I-BEAM mount, and the view from below)","scaleRef":"the side view at the scale of its A: 69.7 mm = 1149 px (532 to 1681), 418.7 px/in","method":"the top plate's two ends in the traced side view (profiles.side, feature plate: -0.994 and 0.994 in) about the base's, which the frame's origin is the middle of: the plate is as long as the base and over it. The four screws' heads under it are 1.39 in apart about the same middle (features screw_rear, screw_front): the footprint's middle","via":"harvest"}}]},"mount_length":{"label":"The I-BEAM's length along the rail (its base, and its top plate, which is as long)","kind":"length","measurements":[{"id":"drawing","value":1.98,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{sig-romeo5-gen-ii.mount_length}","via":"harvest"},"note":"Read on the manual's side view of the pair, in the sight's ledger."}]},"clamp_below_rail":{"label":"The I-BEAM base's foot below the rail's top","kind":"length","measurements":[{"id":"drawing","value":0.235,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{sig-romeo5-gen-ii.clamp_below_rail}","via":"harvest"}}]},"weight":{"label":"Weight (the mount, its cross bolt and the four screws that hold the sight to it)","kind":"mass","measurements":[{"id":"metal","value":58.6,"unit":"g","pm":6,"source":{"type":"derived","basis":"The model's volume: the I-BEAM 1.2796 cubic inches as aluminium (std.density.aluminium, 0.098 lb a cubic inch: 56.9 g) and the bolt and screws 0.0132 as steel (std.density.steel, 4.565 oz a cubic inch: 1.7 g), from pipeline/blender/sig_romeo5_gen_ii.py's manifest. The ± is a tenth: the web is lighter than drawn (the note)."}}],"note":"SIG gives no weight for the mount. Weighed by its metal as modelled (CLAUDE.md: a piece no page gives a weight for), which is more than it weighs: the manual gives the Tall model, whose only difference is a mount 13.2 mm taller, 4 g more, where this web drawn that much taller would add about 11 g, so the real web is lighter than the outlines' hull it is drawn as. The sight alone is the manual's 155 g less this (sig-romeo5-gen-ii.sight_weight)."}}},{"subject":"sig-tango-msr-1-6x24","title":"SIG SAUER TANGO-MSR 1-6x24","dimensions":{"length":{"label":"Overall length (the objective's front face to the eyepiece's rear face)","kind":"length","measurements":[{"id":"sig","value":10.4,"unit":"in","stated":"Overall Length 10.4 in","source":{"type":"spec","publisher":"manufacturer","name":"SIG SAUER, TANGO-MSR LPVO 1-6x24mm SFP product page, SPECIFICATIONS table (read by the user on the page and pasted in chat as a screenshot; not on file)","url":"https://www.sigsauer.com/tango-msr-lpvo-1-6x24mm-sfp.html","retrieved":"2026-10-01","via":"user"}},{"id":"gsg","value":264,"unit":"mm","stated":"Maße: 264 x 70 x 80 mm","source":{"type":"spec","publisher":"retailer","name":"German Sport Guns, SOT61000 (Technische Daten)","url":"https://www.german-sport-guns.com/Sig-Sauer-TANGO-MSR-1-6x24-MSR-BDC6-SFP/SOT61000","retrieved":"2026-10-01","via":"harvest"},"note":"The first of three unlabelled figures."},{"id":"sportsmans","value":10.4,"unit":"in","stated":"Length 10.4in","source":{"type":"spec","publisher":"retailer","name":"Sportsman's Warehouse, item 1696951","url":"https://www.sportsmans.com/hunting-gear-supplies/optics-binoculars-scopes-rangefinders/rifle-scopes-red-dots/sig-sauer-tango-msr-lpvo-1-6x-24mm-rifle-scope-bdc6/p/1696951","retrieved":"2026-10-01","via":"harvest"}},{"id":"xtreme","value":11,"unit":"in","stated":"Length: 11 inches","source":{"type":"spec","publisher":"retailer","name":"Xtreme Guns and Ammo (the coyote model, SOTM61200)","url":"https://xtremegunsandammo.com/shop/optics-for-sale/rifle-scopes-for-sale/sig-sauer-rifle-scopes-for-sale/sig-sauer-tango-msr/sig-sauer-tango-msr-1-6x24/","retrieved":"2026-10-01","via":"harvest"},"note":"The same listing gives a 28 mm objective lens where SIG says 24."}],"adopt":{"from":"sig","reason":"SIG's table; two retailers repeat it (264 mm is 10.39 in). One listing rounds to 11 inches."}},"tube_od":{"label":"Main tube diameter","kind":"length","measurements":[{"id":"sig","value":30,"unit":"mm","stated":"Maintube Diameter 30mm","source":{"type":"spec","publisher":"manufacturer","name":"SIG SAUER, TANGO-MSR LPVO 1-6x24mm SFP product page, SPECIFICATIONS table (read by the user on the page and pasted in chat as a screenshot; not on file)","url":"https://www.sigsauer.com/tango-msr-lpvo-1-6x24mm-sfp.html","retrieved":"2026-10-01","via":"user"}},{"id":"gsg","value":30,"unit":"mm","stated":"Mittelrohr Durchmesser: 30 mm","source":{"type":"spec","publisher":"retailer","name":"German Sport Guns, SOT61000 (Technische Daten)","url":"https://www.german-sport-guns.com/Sig-Sauer-TANGO-MSR-1-6x24-MSR-BDC6-SFP/SOT61000","retrieved":"2026-10-01","via":"harvest"}},{"id":"mount","value":30,"unit":"mm","stated":"P/N: SOA20014 30mm X 1.535\"","source":{"type":"spec","publisher":"manufacturer","name":"SIG SAUER, the engraving on the ALPHA-MSR mount's left side, as it reads in German Sport Guns' left-side product photo (references/sig-tango-msr-1-6x24 a140bd671551) and in the user's photos of the mount","url":"https://www.german-sport-guns.com/media/66/7d/53/1770809536/SOT61000_2.jpg","retrieved":"2026-10-01","via":"harvest"},"note":"The ring size of the mount it ships in."}],"adopt":{"from":"sig","reason":"SIG's table; a retailer and the ring size engraved on its mount say the same."}},"objective_od":{"label":"Objective end, outside diameter","kind":"length","measurements":[{"id":"sig","value":30,"unit":"mm","stated":"Objective Outer Diameter 30 MM","source":{"type":"spec","publisher":"manufacturer","name":"SIG SAUER, TANGO-MSR LPVO 1-6x24mm SFP product page, SPECIFICATIONS table (read by the user on the page and pasted in chat as a screenshot; not on file)","url":"https://www.sigsauer.com/tango-msr-lpvo-1-6x24mm-sfp.html","retrieved":"2026-10-01","via":"user"}},{"id":"gsg","value":30,"unit":"mm","stated":"Objektiv Durchmesser außen: 30 mm","source":{"type":"spec","publisher":"retailer","name":"German Sport Guns, SOT61000 (Technische Daten)","url":"https://www.german-sport-guns.com/Sig-Sauer-TANGO-MSR-1-6x24-MSR-BDC6-SFP/SOT61000","retrieved":"2026-10-01","via":"harvest"}}],"adopt":{"from":"sig","reason":"SIG's table; a retailer repeats it."},"note":"The same as the main tube: a straight 30 mm tube with no bell. The two read alike in both side photos once the photos' yaw is taken out (the trace's checks)."},"objective_lens_d":{"label":"Objective lens diameter","kind":"length","measurements":[{"id":"sig","value":24,"unit":"mm","stated":"Objective Lens Diameter 24 mm","source":{"type":"spec","publisher":"manufacturer","name":"SIG SAUER, TANGO-MSR LPVO 1-6x24mm SFP product page, SPECIFICATIONS table (read by the user on the page and pasted in chat as a screenshot; not on file)","url":"https://www.sigsauer.com/tango-msr-lpvo-1-6x24mm-sfp.html","retrieved":"2026-10-01","via":"user"}},{"id":"gsg","value":24,"unit":"mm","stated":"Objektiv Durchmesser: 24 mm","source":{"type":"spec","publisher":"retailer","name":"German Sport Guns, SOT61000 (Technische Daten)","url":"https://www.german-sport-guns.com/Sig-Sauer-TANGO-MSR-1-6x24-MSR-BDC6-SFP/SOT61000","retrieved":"2026-10-01","via":"harvest"}}],"adopt":{"from":"sig","reason":"SIG's table; a retailer repeats it. (One listing of the coyote model says 28 mm: see length.)"}},"eyepiece_lens_d":{"label":"Ocular lens diameter (the glass, as it shows in the eyepiece's rear)","kind":"length","measurements":[{"id":"rear-oblique","value":1.22,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 fa263ec375cf (German Sport Guns SOT61000_4.jpg, from the rear right)","scaleRef":"the eyepiece's own rear rim in the same view, 543 px along its long axis, taken as 1.826 in (twice the traced body's radius there)","method":"same-plane ratio on a gridded 2x crop: the glass is 362 px along the same direction, 0.667 of the rim. It sits a little way inside the rim, which shows it a percent or two small","via":"harvest"}}]},"weight":{"label":"Weight (the scope alone)","kind":"mass","measurements":[{"id":"sig","value":18.5,"unit":"oz","stated":"Weight 18.5 oz","source":{"type":"spec","publisher":"manufacturer","name":"SIG SAUER, TANGO-MSR LPVO 1-6x24mm SFP product page, SPECIFICATIONS table (read by the user on the page and pasted in chat as a screenshot; not on file)","url":"https://www.sigsauer.com/tango-msr-lpvo-1-6x24mm-sfp.html","retrieved":"2026-10-01","via":"user"}},{"id":"sportsmans","value":18.5,"unit":"oz","stated":"Weight 18.5oz","source":{"type":"spec","publisher":"retailer","name":"Sportsman's Warehouse, item 1696951","url":"https://www.sportsmans.com/hunting-gear-supplies/optics-binoculars-scopes-rangefinders/rifle-scopes-red-dots/sig-sauer-tango-msr-lpvo-1-6x-24mm-rifle-scope-bdc6/p/1696951","retrieved":"2026-10-01","via":"harvest"}},{"id":"gsg","value":525,"unit":"g","stated":"Gewicht: 525 g","source":{"type":"spec","publisher":"retailer","name":"German Sport Guns, SOT61000 (Technische Daten)","url":"https://www.german-sport-guns.com/Sig-Sauer-TANGO-MSR-1-6x24-MSR-BDC6-SFP/SOT61000","retrieved":"2026-10-01","via":"harvest"}},{"id":"no-mount","value":18.5,"unit":"oz","stated":"Weight: 18.5","source":{"type":"spec","publisher":"retailer","name":"Scheels, Tango-MSR LPVO 1-6x24mm No Mount Riflescope (SOTM61001)","url":"https://www.scheels.com/p/sig-sauer-tango-msr-lpvo-1-6x24mm-no-mount-riflescope/1701-SOTM61001/","retrieved":"2026-10-01","via":"harvest"},"note":"The model sold without the mount (another reticle): the same weight, so the figure doesn't count the mount."}],"adopt":{"from":"sig","reason":"SIG's table; retailers repeat it (525 g is 18.52 oz)."},"note":"SIG's table is the scope's sold with its mount, but the no-mount model is listed at the same figure (Scheels, SOTM61001: \"Weight: 18.5\", \"No Mount Riflescope\"), so it is taken as the scope without the mount. SIG doesn't say."},"eye_relief_low":{"label":"Eye relief at 1x","kind":"length","measurements":[{"id":"sig","value":3.93,"unit":"in","stated":"Eye Relief Low (IN) 3.93","source":{"type":"spec","publisher":"manufacturer","name":"SIG SAUER, TANGO-MSR LPVO 1-6x24mm SFP product page, SPECIFICATIONS table (read by the user on the page and pasted in chat as a screenshot; not on file)","url":"https://www.sigsauer.com/tango-msr-lpvo-1-6x24mm-sfp.html","retrieved":"2026-10-01","via":"user"}}]},"eye_relief_high":{"label":"Eye relief at 6x","kind":"length","measurements":[{"id":"sig","value":3.74,"unit":"in","stated":"Eye Relief High (IN) 3.74","source":{"type":"spec","publisher":"manufacturer","name":"SIG SAUER, TANGO-MSR LPVO 1-6x24mm SFP product page, SPECIFICATIONS table (read by the user on the page and pasted in chat as a screenshot; not on file)","url":"https://www.sigsauer.com/tango-msr-lpvo-1-6x24mm-sfp.html","retrieved":"2026-10-01","via":"user"}}]},"objective_front_x":{"label":"Objective's front face, ahead of the mount's rear cross bolt","kind":"length","measurements":[{"id":"right","value":7.008,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a0aec57f834a (German Sport Guns SOT61000.jpg, right side, 3000 x 2000)","scaleRef":"scale from sig-tango-msr-1-6x24.tube_od = 1.1811 in, the tube's own width column by column: 276.1 px over columns 1170–1350, 275.5 px over columns 1545–1640, 274.6 px over columns 2025–2060, 273.0 px over columns 2290–2660; a line through them (rms 0.28 px) changes -1.5% from column 1170 to 2660, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1500)/width, the lens's axis taken to meet the image at column 1500; 233.4 px/in there. The axis is the tube's centre line (tilt -0.23°, rms 0.19 px). Lengths then scaled by 1.0125 so that the end faces are sig-tango-msr-1-6x24.length = 10.4 in apart: at the tube's scale they read 10.272 (-1.2%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.160 in over radius 0.591 (rms 0.002), the rear end's rim sags 0.055 in over radius 0.913 (rms 0.005)","method":"the max end's face: the silhouette's tip at 7.170 less its rim's arc, 0.162 in of sag at radius 0.591151 (the end is seen from 15.3° off square; arc fitted over 115 rows, rms 0.002) of the traced outline (tools/trace.py); the objective's front face, behind its rim's arc","via":"harvest"}},{"id":"left","value":7.029,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a140bd671551 (German Sport Guns SOT61000_2.jpg, left side, 3000 x 2000)","scaleRef":"scale from sig-tango-msr-1-6x24.tube_od = 1.1811 in, the tube's own width column by column: 295.6 px over columns 245–335, 294.0 px over columns 900–965, 292.3 px over columns 1385–1500, 291.4 px over columns 1685–1880; a line through them (rms 0.19 px) changes -1.7% from column 245 to 1880, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1500)/width, the lens's axis taken to meet the image at column 1500; 247.3 px/in there. The axis is the tube's centre line (tilt -0.08°, rms 0.18 px). Lengths then scaled by 1.0062 so that the end faces are sig-tango-msr-1-6x24.length = 10.4 in apart: at the tube's scale they read 10.336 (-0.6%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.099 in over radius 0.588 (rms 0.002), the rear end's rim sags 0.146 in over radius 0.915 (rms 0.002)","method":"the max end's face: the silhouette's tip at 7.129 less its rim's arc, 0.100 in of sag at radius 0.587647 (the end is seen from 9.6° off square; arc fitted over 121 rows, rms 0.002) of the traced outline (tools/trace.py); the objective's front face, behind its rim's arc (the left side, mirrored)","via":"harvest"}}],"adopt":{"from":"right","reason":"The right side is the photo the outline is traced from; the left side, mirrored, agrees within 0.02 in once each photo's perspective on the bolt is taken out."},"note":"Where the scope sits in its mount, as SIG assembles it. Both side photos see the scope's ends from an angle, so each end shows the rim of its face as an arc: the face is where the arc ends, not the silhouette's tip. The bolt's own axis is taken behind its head (right side) or nut (left side) by that photo's perspective: 0.03 and 0.04 in, opposite ways, and with that the two sides agree."},"eyepiece_rear_behind_bolt":{"label":"Eyepiece's rear face, behind the mount's rear cross bolt","kind":"length","measurements":[{"id":"right","value":3.392,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a0aec57f834a (German Sport Guns SOT61000.jpg, right side, 3000 x 2000)","scaleRef":"scale from sig-tango-msr-1-6x24.tube_od = 1.1811 in, the tube's own width column by column: 276.1 px over columns 1170–1350, 275.5 px over columns 1545–1640, 274.6 px over columns 2025–2060, 273.0 px over columns 2290–2660; a line through them (rms 0.28 px) changes -1.5% from column 1170 to 2660, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1500)/width, the lens's axis taken to meet the image at column 1500; 233.4 px/in there. The axis is the tube's centre line (tilt -0.23°, rms 0.19 px). Lengths then scaled by 1.0125 so that the end faces are sig-tango-msr-1-6x24.length = 10.4 in apart: at the tube's scale they read 10.272 (-1.2%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.160 in over radius 0.591 (rms 0.002), the rear end's rim sags 0.055 in over radius 0.913 (rms 0.005)","method":"the min end's face: the silhouette's tip at -3.447 less its rim's arc, 0.055 in of sag at radius 0.912807 (the end is seen from 3.5° off square; arc fitted over 121 rows, rms 0.005) of the traced outline (tools/trace.py); the eyepiece's rear face, behind its rim's arc","via":"harvest"}},{"id":"left","value":3.371,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a140bd671551 (German Sport Guns SOT61000_2.jpg, left side, 3000 x 2000)","scaleRef":"scale from sig-tango-msr-1-6x24.tube_od = 1.1811 in, the tube's own width column by column: 295.6 px over columns 245–335, 294.0 px over columns 900–965, 292.3 px over columns 1385–1500, 291.4 px over columns 1685–1880; a line through them (rms 0.19 px) changes -1.7% from column 245 to 1880, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1500)/width, the lens's axis taken to meet the image at column 1500; 247.3 px/in there. The axis is the tube's centre line (tilt -0.08°, rms 0.18 px). Lengths then scaled by 1.0062 so that the end faces are sig-tango-msr-1-6x24.length = 10.4 in apart: at the tube's scale they read 10.336 (-0.6%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.099 in over radius 0.588 (rms 0.002), the rear end's rim sags 0.146 in over radius 0.915 (rms 0.002)","method":"the min end's face: the silhouette's tip at -3.518 less its rim's arc, 0.147 in of sag at radius 0.914687 (the end is seen from 9.1° off square; arc fitted over 121 rows, rms 0.002) of the traced outline (tools/trace.py); the eyepiece's rear face, behind its rim's arc (the left side, mirrored)","via":"harvest"}}],"adopt":{"from":"right","reason":"The right side is the photo the outline is traced from; the left side, mirrored, agrees within 0.02 in once each photo's perspective on the bolt is taken out."},"note":"The other end, by the same reading. With objective_front_x it adds up to the published length, which set the photos' scale along the scope."},"width":{"label":"Overall width (across the windage and illumination turrets)","kind":"length","measurements":[{"id":"gsg","value":70,"unit":"mm","stated":"Maße: 264 x 70 x 80 mm","source":{"type":"spec","publisher":"retailer","name":"German Sport Guns, SOT61000 (Technische Daten)","url":"https://www.german-sport-guns.com/Sig-Sauer-TANGO-MSR-1-6x24-MSR-BDC6-SFP/SOT61000","retrieved":"2026-10-01","via":"harvest"},"note":"The second of three unlabelled figures."},{"id":"turrets","value":2.595,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{.windage_reach} + {.illumination_reach}","via":"harvest"}}],"adopt":{"from":"turrets","reason":"Each turret's face placed on the scope's own photos through a fitted camera. The retailer's figure is unlabelled, and 0.16 in more than the scope shows."},"note":"No end-on or top view of this scope exists in anything reachable (two discovery passes), and SIG's table gives no width. The two side turrets don't stand out alike: the windage cap is the elevation cap, 1.165 in out, and the illumination knob is a taller stack, 1.43. A retailer's unlabelled three figures begin with the published length, so the second was taken as the width, and halved for both turrets, until 2026-10-04: it would need the knob 1.59 in out."},"windage_reach":{"label":"Windage turret's flat face, distance from the optical axis","kind":"length","measurements":[{"id":"obliques","value":1.165,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 9f208491beb5 (German Sport Guns SOT61000_3.jpg, from the front right and above, 3000 x 2000), fa263ec375cf (SOT61000_4.jpg, from the rear right, 3000 x 2000)","scaleRef":"a pinhole camera fitted to each photo (.cache/scope/turrets/p2_*.py: the 30 mm objective tube's and the eyepiece's silhouette lines, the elevation cap's midline and top edge, the two end rims 10.4 in apart; the cameras 28 to 34 in away, the fitted features within 0.1 to 4.4 px)","method":"the cap's flat face as a circle about the turret's axis, placed where its edge is strongest whatever the start: 1.160 in (the first photo; 1.14 to 1.20 within 80% of the peak) and 1.170 (the second). Leaving out each of the camera's features in turn moves it between 1.14 and 1.20. The elevation cap's height is one of the camera's inputs, so what is read is this reach over that height: 1.00 ± 0.03","via":"harvest"}}],"note":"The elevation cap's top is 1.164 in above the axis (elevation_top_above_axis): the same cap on the same ball. Its chamfer's outer edge, its skirt and its seat read as the elevation cap's too (1.09 against 1.085, radius 0.63 against 0.627, 0.765 against 0.782)."},"illumination_reach":{"label":"Illumination knob's rim, distance from the optical axis","kind":"length","measurements":[{"id":"obliques","value":1.43,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 fc28a853047a (SOT61000_6.jpg, from the front left, 3000 x 2000), a8f3e6d2726c (Freedom Gorilla SGSOT61000_1_HR.jpg, from the front left, 2000 x 2000)","scaleRef":"a pinhole camera fitted to each photo (.cache/scope/turrets/p2_*.py: the 30 mm objective tube's and the eyepiece's silhouette lines, the elevation cap's midline and top edge, the two end rims 10.4 in apart; the cameras 28 to 34 in away, the fitted features within 0.1 to 4.4 px)","method":"the cap's rounded rim as a circle about the knob's axis: 1.43 in (radius 0.585) and 1.41 (0.580); the logo's ring on the face's floor 1.405 and 1.383 (radius 0.273 and 0.272)","via":"harvest"}}],"note":"Its face is dished: the floor, with the logo's medallion, is about 0.03 in inside the rim. The two photos share a viewpoint, and in both the logo sits 0.05 to 0.09 in off the modelled axis, which one viewpoint can't assign to the turret station, to the knob's own axis or to the picture's crop: that is the ±."},"windage_face_d":{"label":"Windage turret, its cap's flat face diameter","kind":"length","measurements":[{"id":"right","value":0.84,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a0aec57f834a (German Sport Guns SOT61000.jpg, right side: the cap seen face-on)","scaleRef":"the 30 mm tube beside it, 274.8 px: 232.7 px/in in the axis's plane; the face stands about 1.4 in nearer the lens, which is 31 in away (the end faces' arcs), so it shows 4.6% large","method":"the dark flat disc is 202 px wide and 207 px tall on a gridded 3x crop (columns 1768–1970, rows 928–1135); 204 px, less the 4.6%","via":"harvest"}},{"id":"obliques","value":0.89,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 9f208491beb5 (German Sport Guns SOT61000_3.jpg, from the front right and above, 3000 x 2000), fa263ec375cf (SOT61000_4.jpg, from the rear right, 3000 x 2000), a0aec57f834a (the right side, face-on)","scaleRef":"a pinhole camera fitted to each photo (.cache/scope/turrets/p2_*.py: the 30 mm objective tube's and the eyepiece's silhouette lines, the elevation cap's midline and top edge, the two end rims 10.4 in apart; the cameras 28 to 34 in away, the fitted features within 0.1 to 4.4 px); the face-on view at the face's own distance (230.8 px/in at the axis's plane, the face 1.165 in nearer a lens 32 to 45 in away)","method":"the face's circle in the two obliques, radius 0.460 and 0.440; face-on a free ellipse of 105.6 x 104.4 px, 0.88 to 0.89 in across","via":"harvest"}}],"adopt":{"from":"obliques","reason":"Three photos; the first reading had the same face-on view 204 px across where the fitted ellipse is 210."}},"windage_skirt_d":{"label":"Windage turret, its ribbed skirt's diameter","kind":"length","measurements":[{"id":"right","value":1.22,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a0aec57f834a (German Sport Guns SOT61000.jpg, right side: the cap seen face-on)","scaleRef":"the 30 mm tube beside it: 232.7 px/in in the axis's plane; the skirt's rim stands about 1.1 in nearer the lens, so it shows 3.7% large","method":"the cap's outer circle is 291 px wide and 297 px tall on a gridded 3x crop (columns 1712–2003, rows 880–1177); 294 px, less the 3.7%","via":"harvest"},"note":"The elevation cap, seen from the side, is 1.26 in across: the same skirt."}]},"illumination_face_d":{"label":"Illumination knob, its cap's face diameter (the disc with the SIG logo)","kind":"length","measurements":[{"id":"left","value":0.95,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a140bd671551 (German Sport Guns SOT61000_2.jpg, left side: the knob seen face-on)","scaleRef":"the 30 mm tube beside it, 293.3 px: 248.3 px/in in the axis's plane; the face stands about 1.4 in nearer the lens (31 in away), so it shows 4.6% large","method":"the dark cap is 247 px across on a gridded 3x crop (columns 1030–1277); less the 4.6%","via":"harvest"}}]},"illumination_ring_d":{"label":"Illumination knob, its knurled ring's diameter","kind":"length","measurements":[{"id":"left","value":1.17,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a140bd671551 (German Sport Guns SOT61000_2.jpg, left side: the knob seen face-on)","scaleRef":"the 30 mm tube beside it: 248.3 px/in in the axis's plane; the ring stands about 1.1 in nearer the lens, so it shows 3.6% large","method":"the light knurled ring is 307 px wide and 298 px tall on a gridded 3x crop (columns 1000–1307, rows 862–1160); 302 px, less the 3.6%","via":"harvest"}}]},"illumination_dial_d":{"label":"Illumination knob, the numbered ring's diameter (next to the saddle)","kind":"length","measurements":[{"id":"oblique","value":1.2,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a8f3e6d2726c (Freedom Gorilla SGSOT61000_1_HR.jpg, from the front left, 2000 x 2000)","scaleRef":"a pinhole camera fitted to each photo (.cache/scope/turrets/p2_*.py: the 30 mm objective tube's and the eyepiece's silhouette lines, the elevation cap's midline and top edge, the two end rims 10.4 in apart; the cameras 28 to 34 in away, the fitted features within 0.1 to 4.4 px)","method":"the glossy numbered ring, from the saddle (0.80 in from the axis) out to illumination_dial_outer: radius 0.60","via":"harvest"}}]},"illumination_dial_outer":{"label":"Illumination knob, the numbered ring's outer end from the optical axis","kind":"length","measurements":[{"id":"oblique","value":0.95,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a8f3e6d2726c (Freedom Gorilla SGSOT61000_1_HR.jpg, from the front left, 2000 x 2000)","scaleRef":"a pinhole camera fitted to each photo (.cache/scope/turrets/p2_*.py: the 30 mm objective tube's and the eyepiece's silhouette lines, the elevation cap's midline and top edge, the two end rims 10.4 in apart; the cameras 28 to 34 in away, the fitted features within 0.1 to 4.4 px)","method":"the station where the numbered ring ends and the ring with the rectangular detent pockets begins (0.95 to 0.97)","via":"harvest"}}]},"illumination_detent_d":{"label":"Illumination knob, the ring with the detent pockets, its diameter","kind":"length","measurements":[{"id":"oblique","value":1.11,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a8f3e6d2726c (Freedom Gorilla SGSOT61000_1_HR.jpg, from the front left, 2000 x 2000)","scaleRef":"a pinhole camera fitted to each photo (.cache/scope/turrets/p2_*.py: the 30 mm objective tube's and the eyepiece's silhouette lines, the elevation cap's midline and top edge, the two end rims 10.4 in apart; the cameras 28 to 34 in away, the fitted features within 0.1 to 4.4 px)","method":"radius 0.555 to 0.56, from 0.97 to 0.99 out to 1.11 to 1.13 in from the axis: the least certain of the stack","via":"harvest"}}]},"illumination_detent_outer":{"label":"Illumination knob, the detent ring's outer end from the optical axis","kind":"length","measurements":[{"id":"oblique","value":1.11,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a8f3e6d2726c (Freedom Gorilla SGSOT61000_1_HR.jpg, from the front left, 2000 x 2000)","scaleRef":"a pinhole camera fitted to each photo (.cache/scope/turrets/p2_*.py: the 30 mm objective tube's and the eyepiece's silhouette lines, the elevation cap's midline and top edge, the two end rims 10.4 in apart; the cameras 28 to 34 in away, the fitted features within 0.1 to 4.4 px)","method":"where the groove before the knurled ring begins","via":"harvest"}}]},"illumination_knurl_inner":{"label":"Illumination knob, the knurled ring's inner end from the optical axis","kind":"length","measurements":[{"id":"oblique","value":1.17,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a8f3e6d2726c (Freedom Gorilla SGSOT61000_1_HR.jpg, from the front left, 2000 x 2000)","scaleRef":"a pinhole camera fitted to each photo (.cache/scope/turrets/p2_*.py: the 30 mm objective tube's and the eyepiece's silhouette lines, the elevation cap's midline and top edge, the two end rims 10.4 in apart; the cameras 28 to 34 in away, the fitted features within 0.1 to 4.4 px)","method":"where the groove ends","via":"harvest"}}],"note":"Between it and the detent ring is a groove whose depth isn't read. The knurled ring's diameter is illumination_ring_d (1.17 face-on, 1.17 here)."},"illumination_knurl_outer":{"label":"Illumination knob, the knurled ring's outer end from the optical axis (where the smooth cap begins)","kind":"length","measurements":[{"id":"oblique","value":1.28,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a8f3e6d2726c (Freedom Gorilla SGSOT61000_1_HR.jpg, from the front left, 2000 x 2000)","scaleRef":"a pinhole camera fitted to each photo (.cache/scope/turrets/p2_*.py: the 30 mm objective tube's and the eyepiece's silhouette lines, the elevation cap's midline and top edge, the two end rims 10.4 in apart; the cameras 28 to 34 in away, the fitted features within 0.1 to 4.4 px)","method":"the cap, smooth with a rounded rim, runs from here to illumination_reach at a radius of 0.58","via":"harvest"}}]},"saddle_radius":{"label":"Turret saddle, the ball's radius (about the turret station on the optical axis)","kind":"length","measurements":[{"id":"obliques","value":0.985,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 fa263ec375cf (SOT61000_4.jpg, from the rear right, 3000 x 2000), a8f3e6d2726c (Freedom Gorilla SGSOT61000_1_HR.jpg, from the front left, 2000 x 2000)","scaleRef":"a pinhole camera fitted to each photo (.cache/scope/turrets/p2_*.py: the 30 mm objective tube's and the eyepiece's silhouette lines, the elevation cap's midline and top edge, the two end rims 10.4 in apart; the cameras 28 to 34 in away, the fitted features within 0.1 to 4.4 px)","method":"a ball about the turret station whose outline lies on the saddle's silhouette between the turrets in both photos (.cache/scope/turrets/o2-saddle-*.png)","via":"harvest"}},{"id":"side","value":0.986,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a0aec57f834a (German Sport Guns SOT61000.jpg, right side: the traced body, profiles.body)","scaleRef":"the traced body outline's own (the 30 mm tube)","method":"the saddle meets the tube at x 2.377 and 3.958, 0.79 in either side of the station, where a ball about the axis has the tube's radius: the root of 0.79 squared and 0.59 squared. A ball of that radius is 0.762 at x 2.55, where the outline has 0.75","via":"harvest"}}],"adopt":{"from":"obliques","reason":"Laid over the saddle itself in two photos; the side outline's ends give the same ball."},"note":"A ball with four flats (saddle_flat_*), the tube running through it: between the turrets it stands 0.17 in prouder than the 0.81 in barrel the side outline, turned about the axis, made of it."},"saddle_flat_top":{"label":"Turret saddle, its top flat above the optical axis (the elevation turret's seat)","kind":"length","measurements":[{"id":"side","value":0.78,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a0aec57f834a (German Sport Guns SOT61000.jpg, right side: profiles.turret and profiles.body)","scaleRef":"the traced outlines' own (the 30 mm tube)","method":"the elevation turret's traced foot, 0.782 in above the axis; the body's outline between x 2.61 and 3.73 reads 0.80 to 0.82, which is the flat seen with the turret's skirt on it","via":"harvest"}}]},"saddle_flat_bottom":{"label":"Turret saddle, its bottom flat below the optical axis","kind":"length","measurements":[{"id":"side","value":0.82,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a0aec57f834a (German Sport Guns SOT61000.jpg, right side: profiles.body)","scaleRef":"the traced body outline's own (the 30 mm tube)","method":"the body's outline below the axis between x 2.61 and 3.73","via":"harvest"}}]},"saddle_flat_right":{"label":"Turret saddle, its right flat from the optical axis (the windage turret's seat)","kind":"length","measurements":[{"id":"obliques","value":0.77,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 9f208491beb5 (German Sport Guns SOT61000_3.jpg, from the front right and above, 3000 x 2000), fa263ec375cf (SOT61000_4.jpg, from the rear right, 3000 x 2000)","scaleRef":"a pinhole camera fitted to each photo (.cache/scope/turrets/p2_*.py: the 30 mm objective tube's and the eyepiece's silhouette lines, the elevation cap's midline and top edge, the two end rims 10.4 in apart; the cameras 28 to 34 in away, the fitted features within 0.1 to 4.4 px)","method":"the outer edge of the dark groove the windage cap sits in, as a circle about its axis: 0.77 and 0.76 in from the optical axis","via":"harvest"}}]},"saddle_flat_left":{"label":"Turret saddle, its left flat from the optical axis (the illumination knob's seat)","kind":"length","measurements":[{"id":"oblique","value":0.8,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a8f3e6d2726c (Freedom Gorilla SGSOT61000_1_HR.jpg, from the front left, 2000 x 2000)","scaleRef":"a pinhole camera fitted to each photo (.cache/scope/turrets/p2_*.py: the 30 mm objective tube's and the eyepiece's silhouette lines, the elevation cap's midline and top edge, the two end rims 10.4 in apart; the cameras 28 to 34 in away, the fitted features within 0.1 to 4.4 px)","method":"where the knob's numbered ring begins","via":"harvest"}}]},"objective_bore_d":{"label":"Objective, the mouth's inside diameter","kind":"length","measurements":[{"id":"obliques","value":1.01,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 9f208491beb5 (German Sport Guns SOT61000_3.jpg, from the front right and above, 3000 x 2000), fc28a853047a (SOT61000_6.jpg, from the front left, 3000 x 2000)","scaleRef":"a pinhole camera fitted to each photo (.cache/scope/turrets/p2_*.py: the 30 mm objective tube's and the eyepiece's silhouette lines, the elevation cap's midline and top edge, the two end rims 10.4 in apart; the cameras 28 to 34 in away, the fitted features within 0.1 to 4.4 px)","method":"where the mouth goes black, as a circle on the front face: radius 0.508 and 0.501","via":"harvest"}}],"note":"A wall of 0.085 in at the mouth, with a small chamfer inside it."},"objective_lens_recess":{"label":"Objective, the front lens behind the front face","kind":"length","measurements":[{"id":"oblique","value":0.47,"unit":"in","pm":0.1,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 fc28a853047a (SOT61000_6.jpg, from the front left, 3000 x 2000)","scaleRef":"a pinhole camera fitted to each photo (.cache/scope/turrets/p2_*.py: the 30 mm objective tube's and the eyepiece's silhouette lines, the elevation cap's midline and top edge, the two end rims 10.4 in apart; the cameras 28 to 34 in away, the fitted features within 0.1 to 4.4 px)","method":"a glint that follows a ring inside the bore: 0.45 in deep at its own best radius (0.458), 0.46 at the 24 mm lens's, 0.50 at the bore's; one photo, and the same ring wasn't found in the other","via":"harvest"}}]},"eyepiece_rim_id":{"label":"Eyepiece, the rear rim's inside diameter","kind":"length","measurements":[{"id":"oblique","value":1.48,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 fa263ec375cf (SOT61000_4.jpg, from the rear right, 3000 x 2000)","scaleRef":"a pinhole camera fitted to each photo (.cache/scope/turrets/p2_*.py: the 30 mm objective tube's and the eyepiece's silhouette lines, the elevation cap's midline and top edge, the two end rims 10.4 in apart; the cameras 28 to 34 in away, the fitted features within 0.1 to 4.4 px)","method":"the rim's inner edge falls between circles of radius 0.70 and 0.78 drawn on the rear face (.cache/scope/turrets/o3-fa26-ocular.png): their middle, by eye; one photo","via":"harvest"}}],"note":"Between the rim's inner edge and the eye lens the wall is black and tapers in."},"eyepiece_lens_recess":{"label":"Eyepiece, the eye lens ahead of the rear face","kind":"length","measurements":[{"id":"oblique","value":0.3,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 fa263ec375cf (SOT61000_4.jpg, from the rear right, 3000 x 2000)","scaleRef":"a pinhole camera fitted to each photo (.cache/scope/turrets/p2_*.py: the 30 mm objective tube's and the eyepiece's silhouette lines, the elevation cap's midline and top edge, the two end rims 10.4 in apart; the cameras 28 to 34 in away, the fitted features within 0.1 to 4.4 px)","method":"a circle of the lens's diameter (eyepiece_lens_d) about the axis, set back until its edge lies on the lens's: 0.15 in deep falls short of it and 0.45 past it; one photo","via":"harvest"}}]},"elevation_top_above_axis":{"label":"Elevation turret, its cap's top above the optical axis","kind":"length","measurements":[{"id":"right","value":1.164,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a0aec57f834a (German Sport Guns SOT61000.jpg, right side, 3000 x 2000)","scaleRef":"scale from sig-tango-msr-1-6x24.tube_od = 1.1811 in, the tube's own width column by column: 276.1 px over columns 1170–1350, 275.5 px over columns 1545–1640, 274.6 px over columns 2025–2060, 273.0 px over columns 2290–2660; a line through them (rms 0.28 px) changes -1.5% from column 1170 to 2660, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1500)/width, the lens's axis taken to meet the image at column 1500; 233.4 px/in there. The axis is the tube's centre line (tilt -0.23°, rms 0.19 px). Lengths then scaled by 1.0125 so that the end faces are sig-tango-msr-1-6x24.length = 10.4 in apart: at the tube's scale they read 10.272 (-1.2%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.160 in over radius 0.591 (rms 0.002), the rear end's rim sags 0.055 in over radius 0.913 (rms 0.005)","method":"y_max in x [2.5, 3.85] of the traced outline (tools/trace.py); the elevation turret's highest point above the tube's axis","via":"harvest"}}]},"lever_tip_above_axis":{"label":"Throw lever's tip above the optical axis, at 1x (straight up)","kind":"length","measurements":[{"id":"right","value":1.867,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a0aec57f834a (German Sport Guns SOT61000.jpg, right side, 3000 x 2000)","scaleRef":"scale from sig-tango-msr-1-6x24.tube_od = 1.1811 in, the tube's own width column by column: 276.1 px over columns 1170–1350, 275.5 px over columns 1545–1640, 274.6 px over columns 2025–2060, 273.0 px over columns 2290–2660; a line through them (rms 0.28 px) changes -1.5% from column 1170 to 2660, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1500)/width, the lens's axis taken to meet the image at column 1500; 233.4 px/in there. The axis is the tube's centre line (tilt -0.23°, rms 0.19 px). Lengths then scaled by 1.0125 so that the end faces are sig-tango-msr-1-6x24.length = 10.4 in apart: at the tube's scale they read 10.272 (-1.2%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.160 in over radius 0.591 (rms 0.002), the rear end's rim sags 0.055 in over radius 0.913 (rms 0.005)","method":"y_max in x [-1.0, -0.2] of the traced outline (tools/trace.py); the throw lever's tip above the tube's axis","via":"harvest"}}]},"height_in_mount":{"label":"Height in its ALPHA-MSR mount (as sold, SOT61000): the clamp's lowest point to the elevation turret's top","kind":"length","measurements":[{"id":"right","value":2.971,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a0aec57f834a (German Sport Guns SOT61000.jpg, right side, 3000 x 2000)","scaleRef":"scale from sig-tango-msr-1-6x24.tube_od = 1.1811 in, the tube's own width column by column: 276.1 px over columns 1170–1350, 275.5 px over columns 1545–1640, 274.6 px over columns 2025–2060, 273.0 px over columns 2290–2660; a line through them (rms 0.28 px) changes -1.5% from column 1170 to 2660, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1500)/width, the lens's axis taken to meet the image at column 1500; 233.4 px/in there. The axis is the tube's centre line (tilt -0.23°, rms 0.19 px). Lengths then scaled by 1.0125 so that the end faces are sig-tango-msr-1-6x24.length = 10.4 in apart: at the tube's scale they read 10.272 (-1.2%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.160 in over radius 0.591 (rms 0.002), the rear end's rim sags 0.055 in over radius 0.913 (rms 0.005)","method":"(y_max in x [2.5, 3.85]) − (y_min) of the traced outline (tools/trace.py); the elevation turret's top above the clamp's lowest point (the lever, which stands higher at 1x, left out)","via":"harvest"}},{"id":"gsg","value":80,"unit":"mm","stated":"Maße: 264 x 70 x 80 mm","source":{"type":"spec","publisher":"retailer","name":"German Sport Guns, SOT61000 (Technische Daten)","url":"https://www.german-sport-guns.com/Sig-Sauer-TANGO-MSR-1-6x24-MSR-BDC6-SFP/SOT61000","retrieved":"2026-10-01","via":"harvest"},"note":"The third of three unlabelled figures."}],"adopt":{"from":"right","reason":"Measured on the scope's own side view between named points. The retailer's unlabelled 80 mm matches neither this nor the height to the lever's tip."},"note":"Without the throw lever, which stands higher at 1x and swings round with the magnification ring. A retailer's unlabelled third figure, 80 mm, is neither this (75 mm) nor the height to the lever's tip (93 mm). The clamp's lowest point in the side view is its near lower edge, which a lens a few degrees above the axis shows about 0.04 in low."},"saddle_x":{"label":"Turret saddle's middle ahead of the frame's origin (where the turrets' axes cross the optical axis)","kind":"length","measurements":[{"id":"right","value":3.174,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a0aec57f834a (German Sport Guns SOT61000.jpg, right side: the elevation turret, profiles.turret)","scaleRef":"the traced outline's own: the 30 mm tube column by column, lengths to the published 10.4 in","method":"the middle of the elevation turret's traced outline, 2.545 to 3.803 in ahead of the origin: a cap turned about its own upright axis","via":"harvest"}}]},"tube_rear_from":{"label":"Main tube behind the saddle, where it begins ahead of the magnification ring's housing","kind":"length","measurements":[{"id":"right","value":0.19,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a0aec57f834a (German Sport Guns SOT61000.jpg, right side: the turned body, profiles.body)","scaleRef":"the traced body outline's own: the 30 mm tube column by column, lengths to the published 10.4 in (profiles.body)","method":"where the outline's reach above the axis comes down to within 0.012 in of the tube's radius ahead of the magnification ring; the tube shows from there to 1.135 in, where the rear ring begins","via":"harvest"}}],"note":"Behind it the body widens to the magnification ring: a ring can't be clamped there."},"tube_rear_to":{"label":"Main tube behind the saddle, where it ends at the saddle","kind":"length","measurements":[{"id":"right","value":2.397,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a0aec57f834a (German Sport Guns SOT61000.jpg, right side: the turned body, profiles.body)","scaleRef":"the traced body outline's own: the 30 mm tube column by column, lengths to the published 10.4 in (profiles.body)","method":"where the outline leaves the tube's radius (by 0.012 in) going up onto the saddle; the tube shows back from there to 1.828 in, where the rear ring ends","via":"harvest"}},{"id":"ball","value":2.3857,"unit":"in","source":{"type":"derived","expr":"{.saddle_x} - sqrt({.saddle_radius} * {.saddle_radius} - {.tube_od} * {.tube_od} / 4)","via":"harvest"}}],"adopt":{"from":"ball","reason":"The saddle as it is drawn: a ball about the turret station, which meets the tube here. The outline reads 0.011 in ahead, inside its own tolerance; the ball's is the end that keeps a ring off the saddle."}},"tube_front_from":{"label":"Main tube ahead of the saddle, where it begins at the saddle","kind":"length","measurements":[{"id":"right","value":3.946,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a0aec57f834a (German Sport Guns SOT61000.jpg, right side: the turned body, profiles.body)","scaleRef":"the traced body outline's own: the 30 mm tube column by column, lengths to the published 10.4 in (profiles.body)","method":"where the outline comes down off the saddle to within 0.012 in of the tube's radius; the tube shows from there to 4.269 in, where the front ring begins","via":"harvest"}},{"id":"ball","value":3.9623,"unit":"in","source":{"type":"derived","expr":"{.saddle_x} + sqrt({.saddle_radius} * {.saddle_radius} - {.tube_od} * {.tube_od} / 4)","via":"harvest"}}],"adopt":{"from":"ball","reason":"As tube_rear_to: the ball the saddle is drawn as, 0.016 in ahead of where the outline reads it, inside the outline's tolerance."}},"tube_front_to":{"label":"Main tube ahead of the saddle, where it ends (the objective's front rim: a straight tube, no bell)","kind":"length","measurements":[{"id":"right","value":6.992,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a0aec57f834a (German Sport Guns SOT61000.jpg, right side: the turned body, profiles.body)","scaleRef":"the traced body outline's own: the 30 mm tube column by column, lengths to the published 10.4 in (profiles.body)","method":"the last of the outline at the tube's radius, behind the front rim's arc; the tube shows back from there to 5.031 in, where the front ring ends","via":"harvest"}}],"note":"The tube runs to the objective's front face (objective_front_x, 7.008): nothing but the end of the scope stops a ring here."},"cap_flats":{"label":"Turret caps (elevation and windage: the same cap), the flats round the knurled band","kind":"count","measurements":[{"id":"face-on","value":6,"unit":"count","source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a0aec57f834a (German Sport Guns SOT61000.jpg, right side, 3000 x 2000)","scaleRef":"the 30 mm tube beside the turret: 233.0 px/in at the turret station (the trace's own scale there)","method":"the windage cap face-on, unwrapped about its centre (.cache/scope-knobs: 1440 samples a turn at radii 60 to 160 px): six narrow bars up its chamfer 240 samples apart, 60 degrees, with the rim cut in between each pair","via":"harvest"}},{"id":"profile","value":6,"unit":"count","source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a0aec57f834a (German Sport Guns SOT61000.jpg, right side, 3000 x 2000)","scaleRef":"the 30 mm tube beside the turret: 233.0 px/in at the turret station (the trace's own scale there)","method":"the elevation cap in profile: the stretches of its band with no teeth (row-to-row contrast down each column, rows 773 to 808) are centred 29.4, 29.2, 29.7 and 29.5 degrees apart round a band 0.616 in in radius, wide and narrow by turns: twelve to a turn, six of each","via":"harvest"}},{"id":"oblique","value":6,"unit":"count","source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 fc28a853047a (SOT61000_6.jpg, from the front left, 3000 x 2000)","scaleRef":"a pinhole camera fitted to the photo (.cache/scope/turrets/cam-fc28a853047a.json: the tube's and the eyepiece's silhouette lines, the end rims), and the knob's surface unwrapped through it (.cache/scope-knobs/unwrap.py: a cylinder about the knob's axis sampled a tenth of a degree a pixel)","method":"the elevation cap's band unwrapped from 60 to 212 degrees: two flats 54.5 degrees apart, a rib midway between them (the camera's fit leaves a few degrees)","via":"harvest"}}],"adopt":{"from":"face-on","reason":"Counted round the whole cap in one view; the profile and the oblique give the same spacing over the half each sees."},"note":"Round the band: a flat, a patch of knurl, a narrow plain rib, a patch of knurl, six times. The part's notes said eight flats until this was counted."},"cap_flat_width":{"label":"Turret caps, a flat across at the foot of the knurl beside it","kind":"length","measurements":[{"id":"profile","value":0.233,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a0aec57f834a (German Sport Guns SOT61000.jpg, right side, 3000 x 2000)","scaleRef":"the 30 mm tube beside the turret: 233.0 px/in at the turret station (the trace's own scale there)","method":"the flat facing the lens (9.5 degrees off square: nothing taken off for that, 1.4%), by eye on the lifted crop: its two edges at columns 1781 and 1835.5, 54.4 px","via":"harvest"}},{"id":"oblique","value":0.246,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 fc28a853047a (SOT61000_6.jpg, from the front left, 3000 x 2000)","scaleRef":"a pinhole camera fitted to the photo (.cache/scope/turrets/cam-fc28a853047a.json: the tube's and the eyepiece's silhouette lines, the end rims), and the knob's surface unwrapped through it (.cache/scope-knobs/unwrap.py: a cylinder about the knob's axis sampled a tenth of a degree a pixel)","method":"the two flats in the unwrapped band are 23 and 24 degrees wide: the chord of 23.5 degrees at the roots' radius","via":"harvest"}}],"adopt":{"from":"profile","reason":"Read on the straight view, at the turret's own scale; the oblique's is through a fitted camera and agrees within its ±."},"note":"A plane cut across the band. With no teeth showing, the stretch is 0.309 in across in the profile view (29.5 degrees at the teeth's tops): a plane through this chord at the teeth's roots cuts the teeth beside it short out to about that."},"cap_rib_width":{"label":"Turret caps, the plain rib between two patches of knurl","kind":"length","measurements":[{"id":"profile","value":0.08,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a0aec57f834a (German Sport Guns SOT61000.jpg, right side, 3000 x 2000)","scaleRef":"the 30 mm tube beside the turret: 233.0 px/in at the turret station (the trace's own scale there)","method":"two ribs, 7.7 and 7.2 degrees of the band at 38.7 behind and 20.2 ahead of square: 7.5 degrees at the tops' radius, 0.616 in","via":"harvest"}}]},"cap_knurl_rows":{"label":"Turret caps, the knurl's rows of teeth (up the band)","kind":"count","measurements":[{"id":"profile","value":4,"unit":"count","source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a0aec57f834a (German Sport Guns SOT61000.jpg, right side, 3000 x 2000)","scaleRef":"the 30 mm tube beside the turret: 233.0 px/in at the turret station (the trace's own scale there)","method":"the elevation cap's silhouette, which has a patch of knurl at each edge: four teeth up the band, their tops between rows 775 and 803","via":"harvest"}}]},"cap_knurl_columns":{"label":"Turret caps, the knurl's columns of teeth in a patch","kind":"count","measurements":[{"id":"profile","value":2,"unit":"count","source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a0aec57f834a (German Sport Guns SOT61000.jpg, right side, 3000 x 2000)","scaleRef":"the 30 mm tube beside the turret: 233.0 px/in at the turret station (the trace's own scale there)","method":"three patches near the middle of the elevation cap's band (columns 1751 to 1773, 1846 to 1873, 1891 to 1915): the mean down each column has three dark grooves and two teeth between them","via":"harvest"}}],"note":"Three grooves to a patch (one at each edge, one between), 0.035 to 0.037 in apart."},"cap_knurl_pitch":{"label":"Turret caps, the knurl's pitch (tooth to tooth)","kind":"length","measurements":[{"id":"profile","value":0.04,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a0aec57f834a (German Sport Guns SOT61000.jpg, right side, 3000 x 2000)","scaleRef":"the 30 mm tube beside the turret: 233.0 px/in at the turret station (the trace's own scale there)","method":"the four teeth's tops up the elevation cap's silhouette span rows 775 to 803: three pitches in 28 px","via":"harvest"}}],"note":"Up the band. Round it the grooves read 0.035 to 0.037 in apart (8.0 to 8.5 px at the patches near the cap's middle), inside this one's ±: the teeth are taken as square."},"cap_knurl_depth":{"label":"Turret caps, the knurl's depth","kind":"length","measurements":[{"id":"profile","value":0.0125,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a0aec57f834a (German Sport Guns SOT61000.jpg, right side, 3000 x 2000)","scaleRef":"the 30 mm tube beside the turret: 233.0 px/in at the turret station (the trace's own scale there)","method":"the elevation cap's silhouette across the band: 1.232 in across the teeth's tops, 1.207 across the grooves between them (rows 775 to 807)","via":"harvest"}}]},"elevation_cap_turned":{"label":"Elevation cap as photographed: a flat's middle behind square to the right side","kind":"angle","measurements":[{"id":"profile","value":9.5,"unit":"deg","pm":2,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a0aec57f834a (German Sport Guns SOT61000.jpg, right side, 3000 x 2000)","scaleRef":"the 30 mm tube beside the turret: 233.0 px/in at the turret station (the trace's own scale there)","method":"the wide plain stretch nearest the cap's middle runs from 24.3 degrees behind square to 5.2 ahead (columns 1774 to 1845 about the cap's axis at 1832.5)","via":"harvest"}}],"note":"Where the cap was left when SIG's photo was taken: it turns. The flat facing the right side is turned this far toward the eyepiece."},"windage_cap_turned":{"label":"Windage cap as photographed: a rib below level, toward the muzzle (seen from the right)","kind":"angle","measurements":[{"id":"face-on","value":48.75,"unit":"deg","pm":3,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a0aec57f834a (German Sport Guns SOT61000.jpg, right side, 3000 x 2000)","scaleRef":"the 30 mm tube beside the turret: 233.0 px/in at the turret station (the trace's own scale there)","method":"the six bars up the cap's chamfer in the unwrapped view, at 48.75 degrees and every 60 from there, clockwise from the muzzle's direction as the photo has it","via":"harvest"}}],"note":"As the elevation cap's: where it was left. A rib is this far below the muzzle's direction, seen face-on from the right; the flats are midway between ribs (the rim is cut in there)."},"illumination_knurl_patches":{"label":"Illumination knob, the patches of knurl round its knurled ring","kind":"count","measurements":[{"id":"oblique","value":12,"unit":"count","source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 fc28a853047a (SOT61000_6.jpg, from the front left, 3000 x 2000)","scaleRef":"a pinhole camera fitted to the photo (.cache/scope/turrets/cam-fc28a853047a.json: the tube's and the eyepiece's silhouette lines, the end rims), and the knob's surface unwrapped through it (.cache/scope-knobs/unwrap.py: a cylinder about the knob's axis sampled a tenth of a degree a pixel)","method":"the knurled ring unwrapped from 8 degrees behind the top to 136 ahead: lands centred 31 degrees apart, three of them in view, 11.6 to a turn","via":"harvest"}}],"note":"A patch of knurl and a plain land by turns, all the way round as far as the one view shows (a third of the ring)."},"illumination_knurl_land_width":{"label":"Illumination knob, a plain land between two patches of knurl","kind":"length","measurements":[{"id":"oblique","value":0.1,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 fc28a853047a (SOT61000_6.jpg, from the front left, 3000 x 2000)","scaleRef":"a pinhole camera fitted to the photo (.cache/scope/turrets/cam-fc28a853047a.json: the tube's and the eyepiece's silhouette lines, the end rims), and the knob's surface unwrapped through it (.cache/scope-knobs/unwrap.py: a cylinder about the knob's axis sampled a tenth of a degree a pixel)","method":"two lands, each 10 degrees of the ring in the unwrapped view, at its radius (illumination_ring_d / 2)","via":"harvest"}}]},"illumination_knurl_rows":{"label":"Illumination knob, the knurl's rows of teeth (across the ring)","kind":"count","measurements":[{"id":"oblique","value":3,"unit":"count","source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 fc28a853047a (SOT61000_6.jpg, from the front left, 3000 x 2000)","scaleRef":"a pinhole camera fitted to the photo (.cache/scope/turrets/cam-fc28a853047a.json: the tube's and the eyepiece's silhouette lines, the end rims), and the knob's surface unwrapped through it (.cache/scope-knobs/unwrap.py: a cylinder about the knob's axis sampled a tenth of a degree a pixel)","method":"the patch best in view in the unwrapped ring: three rows of square teeth across it","via":"harvest"}}]},"illumination_knurl_columns":{"label":"Illumination knob, the knurl's columns of teeth in a patch","kind":"count","measurements":[{"id":"oblique","value":4,"unit":"count","source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 fc28a853047a (SOT61000_6.jpg, from the front left, 3000 x 2000)","scaleRef":"a pinhole camera fitted to the photo (.cache/scope/turrets/cam-fc28a853047a.json: the tube's and the eyepiece's silhouette lines, the end rims), and the knob's surface unwrapped through it (.cache/scope-knobs/unwrap.py: a cylinder about the knob's axis sampled a tenth of a degree a pixel)","method":"the same patch: four columns of teeth (the one beside it, further round, reads four or five)","via":"harvest"}}]},"illumination_knob_turned":{"label":"Illumination knob as photographed: a land's middle ahead of straight up","kind":"angle","measurements":[{"id":"oblique","value":32,"unit":"deg","pm":3,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 fc28a853047a (SOT61000_6.jpg, from the front left, 3000 x 2000)","scaleRef":"a pinhole camera fitted to the photo (.cache/scope/turrets/cam-fc28a853047a.json: the tube's and the eyepiece's silhouette lines, the end rims), and the knob's surface unwrapped through it (.cache/scope-knobs/unwrap.py: a cylinder about the knob's axis sampled a tenth of a degree a pixel)","method":"the lands in the unwrapped ring are centred 32 and 63 degrees from straight up, toward the muzzle","via":"harvest"}}],"note":"It is the brightness dial: where it stands is the setting it was left at."},"magnification_ring_knurl_panels":{"label":"Magnification ring, the knurled panels round it (a smooth flat between each two)","kind":"count","measurements":[{"id":"right","value":6,"unit":"count","source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a0aec57f834a (German Sport Guns SOT61000.jpg, right side, 3000 x 2000)","scaleRef":"the ring's own radius about the tube's axis: 222 px at this station (0.948 in at 234 px/in, the trace's scale there)","method":"three knurled panels down the side, the grooves down their middles at rows 828, 1030 and near the lower edge, and the lines down the two smooth panels between at rows 922 and 1140: 57, -3, 25 and -32 degrees above level, so 60 degrees from one knurled panel to the next within 3; three a side, six a turn","via":"harvest"}},{"id":"left","value":6,"unit":"count","source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a140bd671551 (German Sport Guns SOT61000_2.jpg, left side, 3000 x 2000)","scaleRef":"the ring's own radius about the tube's axis: 235 px at this station (0.948 in at 248.3 px/in in the axis's plane)","method":"the same three knurled panels down this side, their grooves at rows 797, 1005 and 1206, and the two smooth panels' lines at rows 887 and 1117: 56, -2, -61, 27 and -30 degrees above level","via":"harvest"}}],"adopt":{"from":"right","reason":"The two side views are the two halves of one turn and count the same three a side; neither shows the underside."},"note":"Round the ring a knurled panel and a smooth flat by turns, 60 degrees from one knurled panel to the next. Each side view shows three knurled panels and the two smooth ones between them; the smooth one at the top carries the throw lever's base, and the one underneath shows in neither view: it is what the spacing leaves there, and the model leaves both round. The traced outline's lower edge has teeth in it at the ring's full reach, which a smooth panel underneath doesn't explain: with the knurl's tops at that reach the panels' spacing reads 60 degrees within 3; were the tops 3 to 4% further out it would read 56 to 58, with a wider panel under the lever. Not settled: it wants the ring unwrapped through a camera fitted to an oblique. Each smooth panel has a line down its middle about 0.017 in wide, which isn't drawn."},"magnification_ring_knurl_panel_width":{"label":"Magnification ring, a knurled panel's width round the ring","kind":"angle","measurements":[{"id":"sides","value":27,"unit":"deg","pm":2,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a0aec57f834a and a140bd671551 (German Sport Guns SOT61000.jpg and SOT61000_2.jpg, the right and left sides)","scaleRef":"the ring's own radius about the tube's axis in each photo (222 and 235 px)","method":"the panel that faces the lens: rows 982 to 1088 on the right photo (26 degrees) and 947 to 1060 on the left (27)","via":"harvest"}}],"note":"Two bands of knurl and the groove between them. The smooth flat between two panels is what is left of 60 degrees."},"magnification_ring_knurl_groove_width":{"label":"Magnification ring, the groove along a knurled panel between its two bands of knurl","kind":"length","measurements":[{"id":"sides","value":0.09,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a0aec57f834a and a140bd671551 (German Sport Guns SOT61000.jpg and SOT61000_2.jpg, the right and left sides)","scaleRef":"the 30 mm tube: 234 and 248.3 px/in in the axis's plane; the panel facing the lens is 0.95 in nearer it and shows about 3% large","method":"the dark groove down the middle of the panel that faces the lens: 22 px on each photo (rows 1022 to 1045 and 992 to 1015), less the 3%","via":"harvest"}}],"note":"Its depth isn't read: it is drawn as deep as the knurl."},"magnification_ring_knurl_rows":{"label":"Magnification ring, the rows of teeth in a band of knurl (round the ring)","kind":"count","measurements":[{"id":"sides","value":3,"unit":"count","source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a0aec57f834a and a140bd671551 (German Sport Guns SOT61000.jpg and SOT61000_2.jpg, the right and left sides)","scaleRef":"none: a count","method":"the two bands of the panel that faces the lens, and the bands above and below it, in both photos: three rows of teeth in each","via":"harvest"}}],"note":"Each row is about eighteen square teeth along the ring (0.058 in apart, as the rows are; not counted tooth by tooth). The model draws a row as one rib: the cuts across it aren't made."},"magnification_ring_knurl_length":{"label":"Magnification ring, a band of knurl's length along the ring","kind":"length","measurements":[{"id":"sides","value":1.04,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a0aec57f834a and a140bd671551 (German Sport Guns SOT61000.jpg and SOT61000_2.jpg, the right and left sides)","scaleRef":"the 30 mm tube: 234 and 248.3 px/in in the axis's plane; the panel facing the lens is 0.95 in nearer it and shows about 3% large","method":"the teeth of the panel that faces the lens: columns 822 to 1075 on the right photo (1.045 in) and 1992 to 2258 on the left (1.035)","via":"harvest"}}]},"magnification_ring_knurl_depth":{"label":"Magnification ring, the knurl's depth","kind":"length","measurements":[{"id":"outline","value":0.017,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/sig-tango-msr-1-6x24 a0aec57f834a (German Sport Guns SOT61000.jpg, right side: the turned body, profiles.body)","scaleRef":"the traced body outline's own: the 30 mm tube column by column (profiles.body)","method":"the ring's silhouette along its lower edge, where a band of knurl is in profile: the outline's teeth, tops to roots","via":"harvest"}}]}}},{"subject":"silencerco-sparrow-22","title":"SilencerCo Sparrow 22","dimensions":{"overall_length":{"label":"Overall length","kind":"length","measurements":[{"id":"manual","value":5.08,"unit":"in","stated":"LENGTH 5.08”","source":{"type":"spec","publisher":"manufacturer","name":"SilencerCo, Sparrow 22 Field Manual (copy hosted by Silencer Central; references/silencerco-sparrow-22/docs/b5839c1eb3.pdf)","url":"https://www-wp.silencercentral.com/wp/wp-content/uploads/2025/12/Manual_Sparrow-22.pdf","retrieved":"2026-10-01","via":"harvest"},"note":"Page 3, Overview & Product Specs."},{"id":"spec-sheet","value":5.08,"unit":"in","stated":"Length 5.08”","source":{"type":"spec","publisher":"manufacturer","name":"SilencerCo, Sparrow 22 spec sheet (SKU SU75; copy hosted by Silencer Central; references/silencerco-sparrow-22/docs/480513c4da.pdf)","url":"https://www-wp.silencercentral.com/wp/wp-content/uploads/2025/12/spec-sheet_sparrow22.pdf","retrieved":"2026-10-01","via":"harvest"}},{"id":"ammotogo","value":5.125,"unit":"in","stated":"Length 5.125 inches","source":{"type":"spec","publisher":"review","name":"Ammunition To Go, Sparrow vs Switchback comparison table","url":"https://www.ammunitiontogo.com/lodge/best-22-suppressor-sparrow-vs-switchback/","retrieved":"2026-10-01","via":"harvest"},"note":"An article's comparison table; not SilencerCo's figure, and not said to be measured."}],"adopt":{"from":"manual","reason":"SilencerCo's manual and spec sheet agree. A comparison article says 5.125."}},"length":{"label":"Length ahead of the barrel's shoulder, installed (to the front face)","kind":"length","measurements":[{"id":"shouldered","value":5.08,"unit":"in","source":{"type":"derived","expr":"{.overall_length}","via":"harvest"}}],"note":"The whole silencer: SilencerCo wants its mount's face on the barrel's shoulder (manual p. 1: \"There should be no visible gap between the barrel shoulder and the face of the silencer thread mount\"), and in Primary Arms' photo of the mount end (09406a0f6baa) that face is flush with the back cap's rear, with no skirt reaching back over the barrel. With SilencerCo's spacer on a longer thread it would stand off by the spacer's length, which isn't sourced."},"half_length":{"label":"Half the overall length (where the traced outline's middle sits from the rear face)","kind":"length","measurements":[{"id":"half","value":2.54,"unit":"in","source":{"type":"derived","expr":"{.overall_length} / 2","via":"harvest"}}]},"od":{"label":"Largest outside diameter (the tube)","kind":"length","measurements":[{"id":"manual","value":1.06,"unit":"in","stated":"DIAMETER 1.06”","source":{"type":"spec","publisher":"manufacturer","name":"SilencerCo, Sparrow 22 Field Manual (copy hosted by Silencer Central; references/silencerco-sparrow-22/docs/b5839c1eb3.pdf)","url":"https://www-wp.silencercentral.com/wp/wp-content/uploads/2025/12/Manual_Sparrow-22.pdf","retrieved":"2026-10-01","via":"harvest"}},{"id":"spec-sheet","value":1.07,"unit":"in","stated":"Diameter 1.07”","source":{"type":"spec","publisher":"manufacturer","name":"SilencerCo, Sparrow 22 spec sheet (SKU SU75; copy hosted by Silencer Central; references/silencerco-sparrow-22/docs/480513c4da.pdf)","url":"https://www-wp.silencercentral.com/wp/wp-content/uploads/2025/12/spec-sheet_sparrow22.pdf","retrieved":"2026-10-01","via":"harvest"}},{"id":"capitol","value":1.062,"unit":"in","stated":"Diameter 1.062\"","source":{"type":"spec","publisher":"retailer","name":"Capitol Armory, Technical Specs","url":"https://www.capitolarmory.com/silencerco-ss-sparrow-22-rimfire-suppressor.html","retrieved":"2026-10-01","via":"harvest"},"note":"The same page's description says \"1.06\\\" diameter\"."}],"adopt":{"from":"manual","reason":"The manual's 1.06; the dealer's 1.062 agrees with it and not with the spec sheet's 1.07. The difference is 0.01 in."},"note":"SilencerCo's two documents differ in the second decimal. A dealer's table gives 1.062, which is 1 1/16 in and rounds to the manual's."},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"manual","value":6.5,"unit":"oz","stated":"WEIGHT 6.5 OZ","source":{"type":"spec","publisher":"manufacturer","name":"SilencerCo, Sparrow 22 Field Manual (copy hosted by Silencer Central; references/silencerco-sparrow-22/docs/b5839c1eb3.pdf)","url":"https://www-wp.silencercentral.com/wp/wp-content/uploads/2025/12/Manual_Sparrow-22.pdf","retrieved":"2026-10-01","via":"harvest"}},{"id":"spec-sheet","value":6.5,"unit":"oz","stated":"Weight 6.5 oz","source":{"type":"spec","publisher":"manufacturer","name":"SilencerCo, Sparrow 22 spec sheet (SKU SU75; copy hosted by Silencer Central; references/silencerco-sparrow-22/docs/480513c4da.pdf)","url":"https://www-wp.silencercentral.com/wp/wp-content/uploads/2025/12/spec-sheet_sparrow22.pdf","retrieved":"2026-10-01","via":"harvest"}},{"id":"pew-science","value":6.5,"unit":"oz","stated":"weighs 6.5 ounces, as tested","source":{"type":"spec","publisher":"review","name":"PEW Science, Sound Signature Review 6.208 (SilencerCo Sparrow on a Beretta 21A)","url":"https://pewscience.com/sound-signature-reviews-free/sss-6-208-silencerco-sparrow-beretta-21a","retrieved":"2026-10-01","via":"harvest"},"note":"The one figure a reviewer says was taken on the unit tested."},{"id":"gallensons","value":6.1,"unit":"oz","stated":"Weighing just 6.1 ounces and measuring 5 inches in length","source":{"type":"spec","publisher":"retailer","name":"Gallenson's","url":"https://gallensons.com/product/silencerco-sparrow-22-suppressor/","retrieved":"2026-10-01","via":"harvest"}},{"id":"ammotogo","value":189,"unit":"g","stated":"Weight 189 grams","source":{"type":"spec","publisher":"review","name":"Ammunition To Go, Sparrow vs Switchback comparison table","url":"https://www.ammunitiontogo.com/lodge/best-22-suppressor-sparrow-vs-switchback/","retrieved":"2026-10-01","via":"harvest"}}],"adopt":{"from":"manual","reason":"SilencerCo's manual and spec sheet, and a reviewer's as-tested weight, agree at 6.5 oz. One dealer says 6.1 and an article 189 g (6.67 oz)."}},"thread_length":{"label":"Barrel thread length it is made for","kind":"length","measurements":[{"id":"manual","value":0.4,"unit":"in","stated":"The Sparrow 22 mounts on conventional 1/2 X 28 (Class 3A) threads .400˝ in length","source":{"type":"spec","publisher":"manufacturer","name":"SilencerCo, Sparrow 22 Field Manual (copy hosted by Silencer Central; references/silencerco-sparrow-22/docs/b5839c1eb3.pdf)","url":"https://www-wp.silencercentral.com/wp/wp-content/uploads/2025/12/Manual_Sparrow-22.pdf","retrieved":"2026-10-01","via":"harvest"}}],"note":"What the mount is made to shoulder on. The manual says nothing about threads between this and the spacer's range."},"spacer_thread_min":{"label":"Shortest barrel thread on which SilencerCo's rifle spacer is required","kind":"length","measurements":[{"id":"manual","value":0.6,"unit":"in","stated":"The Delta Thread Rifle Spacer (AC114) is required on threads .600 ˝– .650˝ in length.","source":{"type":"spec","publisher":"manufacturer","name":"SilencerCo, Sparrow 22 Field Manual (copy hosted by Silencer Central; references/silencerco-sparrow-22/docs/b5839c1eb3.pdf)","url":"https://www-wp.silencercentral.com/wp/wp-content/uploads/2025/12/Manual_Sparrow-22.pdf","retrieved":"2026-10-01","via":"harvest"},"note":"Page 4. The spec sheet lists it as shipped with the silencer (\"Ships With: Delta Threaded Rifle Spacer 1/2×28\")."}]},"spacer_thread_max":{"label":"Longest barrel thread for which SilencerCo's rifle spacer is given","kind":"length","measurements":[{"id":"manual","value":0.65,"unit":"in","stated":"The Delta Thread Rifle Spacer (AC114) is required on threads .600 ˝– .650˝ in length.","source":{"type":"spec","publisher":"manufacturer","name":"SilencerCo, Sparrow 22 Field Manual (copy hosted by Silencer Central; references/silencerco-sparrow-22/docs/b5839c1eb3.pdf)","url":"https://www-wp.silencercentral.com/wp/wp-content/uploads/2025/12/Manual_Sparrow-22.pdf","retrieved":"2026-10-01","via":"harvest"}}]},"bore_d":{"label":"Exit bore, as it shows in the front face","kind":"length","measurements":[{"id":"oblique","value":0.27,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/silencerco-sparrow-22 09c2b9592403 (Primary Arms SU75_00, the muzzle end from an angle, 2200 x 1467)","scaleRef":"the tube's silhouette across its axis at the front face, taken as od (1.06): 518 px there (it widens toward the lens: 482 px at mid-length)","method":"same-plane ratio: the bore's dark hole is 130 px across the tube's axis (luminance below 28; the 50% edge is about a pixel outside), 0.251 of the tube's width at the face","via":"harvest"}}]},"notches":{"label":"Back cap, notches round its rim","kind":"count","measurements":[{"id":"side","value":8,"unit":"count","source":{"type":"photo","photo":"references/silencerco-sparrow-22 7610478aca44 (Primary Arms SU75_01, straight side view, 2200 x 1467)","scaleRef":"the tube's diameter, taken as od (1.06): 394 px at the 200 level (372.6 px/in)","method":"luminance profiles down the back cap at 0.06 to 0.22 in from its end and along the notch that faces the lens","via":"harvest"}}],"note":"Four show on the near half of the side photo, 55, 100 and 143 degrees round from the top edge and one near it: 45 degrees apart."},"notch_width":{"label":"Back cap, notch width","kind":"length","measurements":[{"id":"side","value":0.097,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/silencerco-sparrow-22 7610478aca44 (Primary Arms SU75_01, straight side view, 2200 x 1467)","scaleRef":"the tube's diameter, taken as od (1.06): 394 px at the 200 level (372.6 px/in)","method":"luminance profiles down the back cap at 0.06 to 0.22 in from its end and along the notch that faces the lens","via":"harvest"},"note":"The notch facing the lens: its lit floor is 36 px across."}]},"notch_length":{"label":"Back cap, notch length from the rear face (to where its floor runs out at the cap's surface)","kind":"length","measurements":[{"id":"side","value":0.25,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/silencerco-sparrow-22 7610478aca44 (Primary Arms SU75_01, straight side view, 2200 x 1467)","scaleRef":"the tube's diameter, taken as od (1.06): 394 px at the 200 level (372.6 px/in)","method":"luminance profiles down the back cap at 0.06 to 0.22 in from its end and along the notch that faces the lens","via":"harvest"},"note":"The same notch: its floor ends 93 px from the silhouette's end. On the near surface, so the end's 0.04 in of perspective and the surface's nearness about cancel."}],"note":"A notch is a ramp, not a pocket: its floor is deepest at the rear face (notch_floor_across) and rises to the cap's surface here, 34 degrees to the axis by these two figures. Read again on 2026-10-05 from the rear face's own plane in the same photo (column 124.1: rear_face_d's second reading) with the notch's nearness to the lens taken out (it is 0.40 in nearer than the axis, the lens about 13.5 in away): 0.244."},"notch_floor_across":{"label":"Back cap, across two opposite notches' floors at the rear face","kind":"length","measurements":[{"id":"oblique","value":0.712,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/silencerco-sparrow-22 09406a0f6baa (Primary Arms SU75_02, the mount end from an angle, 2200 x 1467)","scaleRef":"a pinhole camera fitted to this photo by the part's own silhouette (.cache/model-fixes/barrels/sparrow/camera.py: the traced side outline turned about its axis, 1.06 in across and 5.08 long, drawn through the camera and laid over the photo's silhouette, 99.0% in common): f 6949 px, the rear face 13.1 in from the lens, the axis 51 deg off the line of sight. The rear face's plane then moved 0.035 in along the axis, so that the dark line round the thread's ring is a circle about the axis (235 points round 240 deg of it, rms 0.003 in). A published size in that plane as a check: the thread's mouth reads 0.478 in across, between the minor and major diameters of a 1/2-28 thread","method":"the rear face unwrapped through that camera, angle round the axis by distance from it in its plane (.cache/model-fixes/barrels/sparrow/unwrap.py, edges.py, stats.py): in the eight notches the flat ring's outer edge is a straight line 0.3525 to 0.359 in from the axis, mean 0.356. Drawn back over the photo with the flat's edge and its eight bites, the outline lies on the photo's (overlay-rear.png: looked at before the figure was used)","via":"harvest"},"note":"The ± is what the camera leaves open: fitted again with the point its axis meets the picture left free (camera.py free_pp: as good a fit of the silhouette, the lens 11.9 in off), the same floors read 0.010 in further from the axis and the flat's edge 0.006. That fit leaves the flat's edge less of a circle (it wanders 0.02 in round the far side, against 0.008), and the side view, which needs no camera, has this one's figures. The spread between the eight notches is 0.007 in across the pair."},{"id":"side","value":0.71,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/silencerco-sparrow-22 7610478aca44 (Primary Arms SU75_01, straight side view, 2200 x 1467)","scaleRef":"for heights, the tube's diameter between its edges at the 200 level, 393.95 px, as od (1.06): 371.68 px/in; for depths toward the lens, the rear face's own rim, whose arc says the lens sees that end from 10.5 deg off square (rear_face_d's second reading: 68.7 px of outline to an inch toward the lens)","method":"the rear end's outline row by row (.cache/model-fixes/barrels/sparrow/side_fit.py): where a notch has taken the rim away the outline stands 1.5 to 6 px inside the rim's arc, and over the notch 51 deg round from the top it is a straight line in the rear face's plane for 20 rows (rms 0.0014 in), 0.3548 in from the axis","via":"harvest"},"note":"One notch of the eight. A pixel of outline is 0.015 in toward the lens here, and the rear face's own column is known to 0.3 px: the ± is a pixel."}],"adopt":{"from":"oblique","reason":"The photo that shows the rear face itself and all eight notches; the straight side view, read by its own scale, has the one notch it shows 0.002 nearer."},"note":"Each floor is flat across its notch and meets the rear face in a straight line; this is from one such line to the one opposite, twice its distance from the axis. The tube's surface is 0.53 from the axis and the rear flat's edge 0.426 (rear_face_d): a notch is 0.07 deep in the rear face and its floor 0.17 under the tube's surface there. Two photos and two methods, 0.002 apart. The reviewer of 2026-10-05 asked for this figure as the notches' depth; it was the one thing wanting to draw them."},"rear_face_d":{"label":"Back cap, the rear flat's outer diameter (where its chamfer begins)","kind":"length","measurements":[{"id":"oblique","value":0.852,"unit":"in","pm":0.016,"source":{"type":"photo","photo":"references/silencerco-sparrow-22 09406a0f6baa (Primary Arms SU75_02, the mount end from an angle, 2200 x 1467)","scaleRef":"a pinhole camera fitted to this photo by the part's own silhouette (.cache/model-fixes/barrels/sparrow/camera.py: the traced side outline turned about its axis, 1.06 in across and 5.08 long, drawn through the camera and laid over the photo's silhouette, 99.0% in common): f 6949 px, the rear face 13.1 in from the lens, the axis 51 deg off the line of sight. The rear face's plane then moved 0.035 in along the axis, so that the dark line round the thread's ring is a circle about the axis (235 points round 240 deg of it, rms 0.003 in). A published size in that plane as a check: the thread's mouth reads 0.478 in across, between the minor and major diameters of a 1/2-28 thread","method":"the rear face unwrapped through that camera (unwrap.py, edges.py, stats.py): on four teeth of the far side, where the flat's edge shows against the white ground, it is 0.4229, 0.4247, 0.4250 and 0.4307 in from the axis, mean 0.426","via":"harvest"},"note":"The ± is the spread between teeth (the centre is good to 0.004 in) and 1.2% for the camera's scale."},{"id":"side","value":0.845,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/silencerco-sparrow-22 7610478aca44 (Primary Arms SU75_01, straight side view, 2200 x 1467)","scaleRef":"the tube's diameter between its edges at the 200 level, 393.95 px, as od (1.06): 371.68 px/in","method":"the rear end's outline row by row (side_fit.py): on the 207 rows clear of the notches it is the arc of one circle about the axis seen from off square, x = x_face - T sqrt(r^2 - y^2), with r 0.4223 ± 0.0010 in, the rear face at column 124.1 ± 0.3 and T 68.7 px to the inch (10.5 deg); rms 0.26 px","via":"harvest"},"note":"The ± is a pixel of the 200 level at each side, more than the fit's own."}],"adopt":{"from":"oblique","reason":"Taken from the same photo and camera as the notches' floors, so that what the two differ by, the notch's depth in the rear face, carries no scale between photos. The side view agrees within 0.007 in."},"note":"The traced side outline has 0.81 here, and that is not the cap: the outline is cut 0.048 in inside the silhouette's rear tip (column 112.9), but the lens sees that end from 10.5 deg off square and the rear face is 0.078 in inside the tip (column 124.1), so the outline's last 0.03 in is the face's rim seen as an arc. The model's rear end is drawn from this figure and the three after it, not from the outline. The front end read the same way (side_front.py) has its face 0.052 in inside its tip, where the outline is cut: nothing to change there. Between the two faces the photo then reads 5.046 in at the tube's scale, 0.7% under the published 5.08, which the model keeps."},"rear_chamfer_x":{"label":"Back cap, the rear chamfer's forward end, from the rear face","kind":"length","measurements":[{"id":"side","value":0.07,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/silencerco-sparrow-22 7610478aca44 (Primary Arms SU75_01, straight side view, 2200 x 1467)","scaleRef":"the tube's diameter between its edges at the 200 level, 393.95 px, as od (1.06): 371.68 px/in","method":"the cap's upper and lower edges column by column, from the rear face at column 124.1 (rear_face_d's second reading): a line at 47 deg through columns 132 to 144 and a line at 15 deg through columns 156 to 174 meet at column 150.05, 0.0698 in ahead of the face; the steep line reaches the face 0.427 in from the axis, where the rim's arc has 0.4223","via":"harvest"},"note":"The ± is two pixels of where two fitted lines cross."}],"note":"The cap's rim is two cones: a steep one from the rear flat's edge, then a shallow one up to its full diameter (rear_break_x)."},"rear_chamfer_d":{"label":"Back cap, its diameter where the rear chamfer ends","kind":"length","measurements":[{"id":"side","value":1.006,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/silencerco-sparrow-22 7610478aca44 (Primary Arms SU75_01, straight side view, 2200 x 1467)","scaleRef":"the tube's diameter between its edges at the 200 level, 393.95 px, as od (1.06): 371.68 px/in","method":"where the same two lines cross (column 150.05): 0.503 in from the axis","via":"harvest"}}]},"rear_break_x":{"label":"Back cap, where its rim reaches the cap's full diameter, from the rear face","kind":"length","measurements":[{"id":"side","value":0.149,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/silencerco-sparrow-22 7610478aca44 (Primary Arms SU75_01, straight side view, 2200 x 1467)","scaleRef":"the tube's diameter between its edges at the 200 level, 393.95 px, as od (1.06): 371.68 px/in","method":"the 15 deg line through columns 156 to 174 reaches the cap's cylinder (0.524 in from the axis over columns 180 to 210) at column 179.6","via":"harvest"},"note":"The ± is three pixels: a shallow line meeting a level one."}],"note":"The cap's own cylinder is 0.524 from the axis in this photo, 0.006 under the tube's 0.53: the traced outline has that step as a slow taper."},"rear_cap_seam_x":{"label":"Back cap, the seam where it meets the tube, from the rear face","kind":"length","measurements":[{"id":"side","value":0.445,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/silencerco-sparrow-22 7610478aca44 (Primary Arms SU75_01, straight side view, 2200 x 1467)","scaleRef":"the tube's diameter between its edges at the 200 level, 393.95 px, as od (1.06): 371.68 px/in; the rear face at column 124.1 (rear_face_d's second reading)","method":"the seam's dark line found on 73 rows across the tube (.cache/colors/small-steel-22/seams2.py: the darkest column against a running median, rows 590 to 878) and fitted as a circle about the axis seen from off square, column = plane - T sqrt(r^2 - y^2): the plane at column 286.3 with T free (51 px to the inch) and at 294.5 with the rear face's own 68.7; taken where the lens's 13.5 in puts it for this station (T about 58): column 289.5","via":"harvest"},"note":"The ± is the spread of the plane between the two values of T, and the fit's scatter (6 px a row: the line is faint)."}],"note":"For the colours (2026-10-06): the two caps are black oxide and the outer tube magnesium phosphate (Capitol Armory: \"Black Oxide, Magnesium Phosphate (Outer Tube)\"), and the photos show the difference: the model's caps are their own pieces from this seam and front_cap_seam_behind_face. The seam is a circle about the axis: on the near surface it shows as an arc, bowed toward the rear by how far the lens sees that end from off square."},"front_cap_seam_behind_face":{"label":"Front cap, the seam where it meets the tube, behind the front face","kind":"length","measurements":[{"id":"side","value":0.07,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/silencerco-sparrow-22 7610478aca44 (Primary Arms SU75_01, straight side view, 2200 x 1467)","scaleRef":"the tube's diameter between its edges at the 200 level, 393.95 px, as od (1.06): 371.68 px/in; the front face at column 1999.6 (side_front.py, as rear_face_d's note has it), seen from 6 deg off square (39 px to the inch toward the lens)","method":"the seam's dark line on 88 rows (.cache/colors/small-steel-22/seams2.py), each taken back to the seam's own plane by the near surface's depth at its row: 0.056 to 0.086 in behind the face, median 0.074","via":"harvest"},"note":"The ± covers the wave (0.015 in either way) and the angle the end is seen from (0.062 to 0.081 for 30 to 45 px to the inch)."}],"note":"The seam is waved (eight waves round the tube, as the photos show); this is the middle of the wave, and the model draws the seam straight there."}}},{"subject":"slr-sentry-7-gas-block","title":"SLR Rifleworks Sentry 7 Set Screw Adjustable Gas Block (.750, Melonite, .400 set screw spacing, SA7-SM)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"maker","value":1.3,"unit":"oz","pm":0.05,"stated":"Sentry .750\" Set Screw Version - Melonite QPQ Finish .400\" Set Screw Spacing 1.3 oz","source":{"type":"spec","publisher":"manufacturer","name":"SLR Rifleworks, Sentry 7 Set Screw Adjustable Gas Block (SA7-SM), Description","url":"https://slrrifleworks.com/sentry-7-set-screw-adjustable-gas-block/","retrieved":"2026-10-28","via":"harvest"}},{"id":"primary-arms","value":1.3,"unit":"oz","pm":0.05,"stated":"Weight: 1.3 oz","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, SLR Rifleworks Sentry 7 AR-15 Adjustable Gas Block - Set Screw - .750\" (SA7-SM), Features","url":"https://www.primaryarms.com/slr-rifleworks-sentry-7-set-screw-adjustable-gas-block-.750","retrieved":"2026-10-28","via":"harvest"}}],"adopt":{"from":"maker","reason":"The maker's figure; Primary Arms' page says the same."},"note":"Neither page says what was on the scale (the set screws, the roll pin, the tool). The model's volume as 4140 steel is the check (app/tests/slr-sentry-7-gas-block.test.ts)."},"journal_id":{"label":"Bore (the journal it fits: .750 or .625)","kind":"length","measurements":[{"id":"maker","value":0.75,"unit":"in","pm":0.0005,"stated":"Sentry .750\" Set Screw Version - Melonite QPQ Finish","source":{"type":"spec","publisher":"manufacturer","name":"SLR Rifleworks, Sentry 7 Set Screw Adjustable Gas Block (SA7-SM), Description","url":"https://slrrifleworks.com/sentry-7-set-screw-adjustable-gas-block/","retrieved":"2026-10-28","via":"harvest"}},{"id":"primary-arms","value":0.75,"unit":"in","pm":0.0005,"stated":"Gas Seat Diameter .750","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, SLR Rifleworks Sentry 7 AR-15 Adjustable Gas Block - Set Screw - .750\" (SA7-SM), Specifications","url":"https://www.primaryarms.com/slr-rifleworks-sentry-7-set-screw-adjustable-gas-block-.750","retrieved":"2026-10-28","via":"harvest"}}],"adopt":{"from":"maker","reason":"The maker's figure; Primary Arms' specifications say the same."}},"set_screw_spacing":{"label":"The two set screws, centre to centre along the block","kind":"length","measurements":[{"id":"maker","value":0.4,"unit":"in","pm":0.0005,"stated":".400\" Set Screw Spacing","source":{"type":"spec","publisher":"manufacturer","name":"SLR Rifleworks, Sentry 7 Set Screw Adjustable Gas Block (SA7-SM), Description","url":"https://slrrifleworks.com/sentry-7-set-screw-adjustable-gas-block/","retrieved":"2026-10-28","via":"harvest"}},{"id":"primary-arms","value":0.4,"unit":"in","pm":0.0005,"stated":".400\" set screw spacing","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, SLR Rifleworks Sentry 7 AR-15 Adjustable Gas Block - Set Screw - .750\" (SA7-SM), Features","url":"https://www.primaryarms.com/slr-rifleworks-sentry-7-set-screw-adjustable-gas-block-.750","retrieved":"2026-10-28","via":"harvest"}}],"adopt":{"from":"maker","reason":"The maker's figure; Primary Arms' page says the same."},"note":"The maker sells the same block with its front screw .450 from the rear one as another product (\"Sentry 7 Set Screw Adjustable Gas Block - .450\\\"\"): \"There is no difference in the blocks just the front set screw location.\""},"port_opening":{"label":"The metering screw's port, fully open","kind":"length","measurements":[{"id":"maker","value":0.125,"unit":"in","pm":0.0005,"stated":"15-position adjustability from 0 - 0.125\" port opening","source":{"type":"spec","publisher":"manufacturer","name":"SLR Rifleworks, Sentry 7 Set Screw Adjustable Gas Block (SA7-SM), Description","url":"https://slrrifleworks.com/sentry-7-set-screw-adjustable-gas-block/","retrieved":"2026-10-28","via":"harvest"}}],"note":"Inside the block, behind the adjustment screw: not drawn. 15 positions from closed to this."},"height_above_bore":{"label":"Top above the bore axis","kind":"length","measurements":[{"id":"patent","value":0.812,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block e33823945e77 (US 9,410,756, sheet 3, FIG. 3: the block from its front, orthographic, 2560 x 3300 (the patent office's PDF))","scaleRef":"frame from the reviewed holes top, under, right, left (648.3 px/in, rms 0.000 in over 4 points)","method":"y_max of the traced outline (tools/trace.py); the outline's top: the boss's top on the bore's vertical centre line","via":"harvest"}},{"id":"photo-front","value":0.848,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block 276bd13fbaaf (SLR's own photo, DSC01311: the front face nearly square on, yawed about 20 degrees to show the right side, 2770 x 1847)","scaleRef":"the bore's opening, an ellipse fitted to the edge of the bright bore inside the black face (482.1 px tall, 452.1 wide: .750 is 642.9 px/in up the face and 602.7 across it)","method":"the silhouette's top on the bore's centre column, 545 px above the bore's centre: the boss's top seen from a little above, so its far edge"}}],"adopt":{"from":"patent","reason":"The patent's front view at the journal's scale. The maker's photo reads the top 0.036 higher: it is taken from a little above (the bore's floor shows), so its silhouette's top is the boss's rear edge."},"note":"Not published. The boss's top over the gas tube. Primary Arms: \"Needs a handguard with at least 1.4\\\" internal diameter to hide underneath\"."},"foot_below_bore":{"label":"The foot's flat below the bore's axis","kind":"length","measurements":[{"id":"patent","value":0.548,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block e33823945e77 (US 9,410,756, sheet 3, FIG. 3: the block from its front, orthographic, 2560 x 3300 (the patent office's PDF))","scaleRef":"frame from the reviewed holes top, under, right, left (648.3 px/in, rms 0.000 in over 4 points)","method":"−y_min of the traced outline (tools/trace.py); the outline's bottom: the foot's flat","via":"harvest"}},{"id":"photo-front","value":0.553,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block 276bd13fbaaf (SLR's own photo, DSC01311: the front face nearly square on, yawed about 20 degrees to show the right side, 2770 x 1847)","scaleRef":"the bore's opening, an ellipse fitted to the edge of the bright bore inside the black face (482.1 px tall, 452.1 wide: .750 is 642.9 px/in up the face and 602.7 across it)","method":"the silhouette's bottom on the bore's centre column and 120 px either side, 356 px below the bore's centre (the foot's front edge, nearest the lens)"}}],"adopt":{"from":"patent","reason":"The patent's front view at the journal's scale; the maker's photo of the product agrees within 0.005."},"note":"Not published."},"width":{"label":"Width across the ring about the bore","kind":"length","measurements":[{"id":"patent","value":0.899,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block e33823945e77 (US 9,410,756, sheet 3, FIG. 3: the block from its front, orthographic, 2560 x 3300 (the patent office's PDF))","scaleRef":"frame from the reviewed holes top, under, right, left (648.3 px/in, rms 0.000 in over 4 points)","method":"width of the traced outline (tools/trace.py); the outline's extent across: the ring about the bore","via":"harvest"}},{"id":"photo-front","value":0.872,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block 276bd13fbaaf (SLR's own photo, DSC01311: the front face nearly square on, yawed about 20 degrees to show the right side, 2770 x 1847)","scaleRef":"the bore's opening, an ellipse fitted to the edge of the bright bore inside the black face (482.1 px tall, 452.1 wide: .750 is 642.9 px/in up the face and 602.7 across it)","method":"the silhouette's edge on the part's left on the bore's row, 262.5 px from the centre across the face (0.436), twice: the front face's edge with its break, the far side of the ring"}}],"adopt":{"from":"patent","reason":"The patent's front view at the journal's scale. The maker's photo reads the left half 0.016 narrower at the front face's broken edge, inside its ±."},"note":"Not published."},"adjuster_above_bore":{"label":"The adjustment screw's axis above the bore's","kind":"length","measurements":[{"id":"patent","value":0.481,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block e33823945e77 (US 9,410,756 sheet 3, the patent office's PDF page 4: FIG. 3 the block from its front, FIG. 4 from its rear, orthographic, 2560 x 3300)","scaleRef":"FIG. 3's bore, a least-squares circle through its stroke (centre (1288.1, 2218.8), radius 243.1 px, rms 1.0 px), as the journal's .750: 648.3 px/in","method":"the screw's two circles in FIG. 3 (least squares through their strokes: centre (976.6, 2218.6), radii 58.4 and 45.3 px, rms 0.6): 311.5 px from the bore's centre, on its vertical centre line (0.2 px off it)","via":"harvest"}}],"note":"At the front face, between the bore and the boss (the instruction sheet: 'At the front of the gas block is a 15-position adjustment screw'). The maker's front view (276bd13fbaaf) has the screw's head 39 px right of the bore's centre line, which its 20 degree yaw puts on the centre line for a head standing 0.15 in out of the face."},"adjuster_head_d":{"label":"The adjustment screw's head, diameter","kind":"length","measurements":[{"id":"patent","value":0.18,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block e33823945e77 (US 9,410,756 sheet 3, the patent office's PDF page 4: FIG. 3 the block from its front, FIG. 4 from its rear, orthographic, 2560 x 3300)","scaleRef":"FIG. 3's bore, a least-squares circle through its stroke (centre (1288.1, 2218.8), radius 243.1 px, rms 1.0 px), as the journal's .750: 648.3 px/in","method":"FIG. 3's outer circle about the screw, 116.8 px across","via":"harvest"}},{"id":"photo-front","value":0.186,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block 276bd13fbaaf (SLR's own photo, DSC01311: the front face nearly square on, yawed about 20 degrees to show the right side, 2770 x 1847)","scaleRef":"the bore's opening, an ellipse fitted to its edge (482.1 px tall as .750: 642.9 px/in)","method":"the head's two sides on its row, 120 px (columns 1455 and 1575)","via":"harvest"}}],"adopt":{"from":"patent","reason":"The patent's circle; the maker's photo reads the head 0.006 larger, within its ±."}},"adjuster_end_d":{"label":"The adjustment screw's end face inside its edge break","kind":"length","measurements":[{"id":"patent","value":0.14,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block e33823945e77 (US 9,410,756 sheet 3, the patent office's PDF page 4: FIG. 3 the block from its front, FIG. 4 from its rear, orthographic, 2560 x 3300)","scaleRef":"FIG. 3's bore, a least-squares circle through its stroke (centre (1288.1, 2218.8), radius 243.1 px, rms 1.0 px), as the journal's .750: 648.3 px/in","method":"FIG. 3's inner circle about the screw, 90.6 px across","via":"harvest"}}]},"adjuster_socket":{"label":"The adjustment screw's hex socket, across its flats","kind":"length","measurements":[{"id":"patent","value":0.067,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block e33823945e77 (US 9,410,756 sheet 3, the patent office's PDF page 4: FIG. 3 the block from its front, FIG. 4 from its rear, orthographic, 2560 x 3300)","scaleRef":"FIG. 3's bore, a least-squares circle through its stroke (centre (1288.1, 2218.8), radius 243.1 px, rms 1.0 px), as the journal's .750: 648.3 px/in","method":"FIG. 3's hexagon, 50 px across its corners (0.077 in) times cos 30","via":"harvest"}}],"note":"The tool in the box is a long hex key; no page says its size."},"adjuster_reach":{"label":"How far the adjustment screw's head stands out of the front face","kind":"length","measurements":[{"id":"photo-front","value":0.17,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block 276bd13fbaaf (SLR's own photo, DSC01311: the front face nearly square on, yawed about 20 degrees to show the right side, 2770 x 1847)","scaleRef":"the bore's opening, an ellipse fitted to the edge of the bright bore inside the black face (482.1 px tall, 452.1 wide): 642.9 px/in up the face, the face turned 20.3 degrees from the lens","method":"the head's end face's middle stands 39 px to the right of the bore's centre column (1515 against 1475.6) while the patent has the screw on the centre line: 39 px over 642.9 px/in times sin 20.3 degrees","via":"harvest"}},{"id":"photo-right","value":0.135,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block b5a6b18f895e (Primary Arms SA7-SM_00: the block from the right, ahead and above, with its roll pin and key, 2200 x 1467)","scaleRef":"an orthographic camera fitted to the photo's silhouette with the traced section (profiles.front) run along the block and the adjustment screw's head on its face, by Nelder-Mead from the best of a grid of directions (.cache/batch15/slr-sentry-7-gas-block/silfit3.py): the lens toward (0.621, 0.506, 0.599) in the part frame, 543.4 px/in, IoU 0.980","method":"a cylinder of the head's diameter on the face, its length left to the same fit","via":"harvest"}},{"id":"photo-left","value":0.13,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block 8a7811f1e180 (Primary Arms SA7-SM_01: the block from the left, ahead and above, 2200 x 1467)","scaleRef":"the same fit: the lens toward (0.766, 0.482, -0.427), 738.9 px/in, IoU 0.978","method":"the same","via":"harvest"}}],"adopt":{"from":"photo-front","reason":"The maker's photo turns the face by an angle its bore's ellipse gives, with no fit traded against the length; the two silhouette fits read the head shorter (their bump is the head's side as well as its end), the fitted cameras' end faces longer."},"note":"As photographed (at whatever setting each was shipped or shot at); the 15 positions' travel isn't published. The two Primary Arms photos' fitted cameras put the head's end face, where it shows in each (b5a6b18f895e at (976, 503), 8a7811f1e180 at (857, 690)), 0.20 and 0.26 in out of the face if it is on the centre line: those cameras' directions trade off against the length (see length), so their end-face readings aren't taken."},"length":{"label":"Length along the barrel","kind":"length","measurements":[{"id":"photo-right","value":0.856,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block b5a6b18f895e (Primary Arms SA7-SM_00: the block from the right, ahead and above, with its roll pin and key, 2200 x 1467)","scaleRef":"an orthographic camera fitted to the photo's silhouette with the traced section (profiles.front) run along the block and the adjustment screw's head on its face, by Nelder-Mead from the best of a grid of directions (.cache/batch15/slr-sentry-7-gas-block/silfit3.py): the lens toward (0.621, 0.506, 0.599) in the part frame, 543.4 px/in, IoU 0.980","method":"the fit's own length; the next best fits (IoU within 0.002) give 0.885 and 0.916: the ± covers them","via":"harvest"}},{"id":"photo-left","value":0.836,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block 8a7811f1e180 (Primary Arms SA7-SM_01: the block from the left, ahead and above, 2200 x 1467)","scaleRef":"the same fit: the lens toward (0.766, 0.482, -0.427), 738.9 px/in, IoU 0.978","method":"the fit's own length; the next best (IoU within 0.0003) gives 0.984 with the screw's head 0.21 out, which the right photo's fit doesn't allow","via":"harvest"}},{"id":"patent","value":0.974,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block fe10f1d408bb (US 9,410,756 sheet 6: FIG. 7 the block's right side, orthographic, 2560 x 3300)","scaleRef":"FIG. 7's height (905 px, the boss's top to the foot's flat) as FIG. 3's at the journal's scale (1.360 in): 665 px/in","method":"FIG. 7's two end faces, 648 px apart","via":"harvest"},"note":"The patent's embodiment, with a window through the ring where the product has three flutes: its proportions, not the product's."},{"id":"photo-front","value":0.842,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block 276bd13fbaaf (SLR's own photo, DSC01311: the front face nearly square on, yawed about 20 degrees to show the right side, 2770 x 1847)","scaleRef":"the bore's opening, an ellipse fitted to the edge of the bright bore inside the black face (482.1 px tall, 452.1 wide): 642.9 px/in up the face, the face turned 20.3 degrees from the lens (the ellipse's axes 0.938 of one another)","method":"the right side's silhouette on the bore's row (column 1016) behind the ring's widest point on the front face (column 1203.9, 0.449 in right of the bore's centre at 602.7 px/in across the face): 187.9 px, over 642.9 px/in times sin 20.3 degrees; as an orthographic view, with the lens's height taken as level (the ± covers a few degrees of it)","via":"harvest"}}],"adopt":{"from":"photo-right","reason":"The right photo sees the block's length most squarely (the lens 53 degrees off its axis), and the left photo's fit and the maker's front photo agree within their ±. The patent's FIG. 7 is longer by 0.12 in, which the published weight does not allow for this section: the product is not the embodiment drawn."},"note":"Not published. The two Primary Arms photos read it through cameras fitted to their silhouettes. The weight is the check: 1.3 oz of 4140 at std.density.steel is 0.285 cubic inches, which the traced section less the bore (0.355 square inches) runs 0.80 in; the flutes and the holes take some of that back, the screws and the spring add some."},"flute_pitch":{"label":"The three flutes down each side, centre to centre along the block","kind":"length","measurements":[{"id":"photo-right","value":0.227,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block b5a6b18f895e (Primary Arms SA7-SM_00: the block from the right, ahead and above, with its roll pin and key, 2200 x 1467)","scaleRef":"an orthographic camera fitted to the photo's silhouette with the traced section (profiles.front) run along the block and the adjustment screw's head on its face, by Nelder-Mead from the best of a grid of directions (.cache/batch15/slr-sentry-7-gas-block/silfit3.py): the lens toward (0.621, 0.506, 0.599) in the part frame, 543.4 px/in, IoU 0.980","method":"each flute's middle at the ring's widest taken back through the camera onto the section's surface: 0.154, 0.387 and 0.607 in behind the front face (backproj.py); the mean of the two spacings (0.233, 0.220)","via":"harvest"}}],"note":"Three on each side: counted on the right side in 276bd13fbaaf and b5a6b18f895e and on the left in 8a7811f1e180. Grooves round the ring, from under the spring's flat down to the foot."},"flute_front_from_front":{"label":"The front flute's middle behind the front face","kind":"length","measurements":[{"id":"photo-right","value":0.154,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block b5a6b18f895e (Primary Arms SA7-SM_00: the block from the right, ahead and above, with its roll pin and key, 2200 x 1467)","scaleRef":"an orthographic camera fitted to the photo's silhouette with the traced section (profiles.front) run along the block and the adjustment screw's head on its face, by Nelder-Mead from the best of a grid of directions (.cache/batch15/slr-sentry-7-gas-block/silfit3.py): the lens toward (0.621, 0.506, 0.599) in the part frame, 543.4 px/in, IoU 0.980","method":"taken back onto the section's surface at the ring's widest (see flute_pitch)","via":"harvest"}}]},"flute_width":{"label":"A flute's width along the block","kind":"length","measurements":[{"id":"photo-right","value":0.106,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block b5a6b18f895e (Primary Arms SA7-SM_00: the block from the right, ahead and above, with its roll pin and key, 2200 x 1467)","scaleRef":"an orthographic camera fitted to the photo's silhouette with the traced section (profiles.front) run along the block and the adjustment screw's head on its face, by Nelder-Mead from the best of a grid of directions (.cache/batch15/slr-sentry-7-gas-block/silfit3.py): the lens toward (0.621, 0.506, 0.599) in the part frame, 543.4 px/in, IoU 0.980","method":"the middle flute's lit wall and shadow together at the ring's widest, 45 px at the fit's 426 px/in along the block","via":"harvest"}}]},"flute_depth":{"label":"A flute's depth into the ring","kind":"length","measurements":[{"id":"assumed","value":0.035,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows a flute in profile (no straight end view of the product); a third of its width, the bottom round.","via":"harvest"}}]},"flute_top_above_bore":{"label":"Where the flutes begin, above the bore's axis","kind":"length","measurements":[{"id":"photo-right","value":0.255,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block b5a6b18f895e (Primary Arms SA7-SM_00: the block from the right, ahead and above, with its roll pin and key, 2200 x 1467)","scaleRef":"an orthographic camera fitted to the photo's silhouette with the traced section (profiles.front) run along the block and the adjustment screw's head on its face, by Nelder-Mead from the best of a grid of directions (.cache/batch15/slr-sentry-7-gas-block/silfit3.py): the lens toward (0.621, 0.506, 0.599) in the part frame, 543.4 px/in, IoU 0.980","method":"the three flutes' upper ends taken back onto the section's surface: 0.258, 0.248, 0.261","via":"harvest"}}]},"flute_bottom_below_bore":{"label":"Where the flutes end, below the bore's axis","kind":"length","measurements":[{"id":"photo-right","value":0.38,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block b5a6b18f895e (Primary Arms SA7-SM_00: the block from the right, ahead and above, with its roll pin and key, 2200 x 1467)","scaleRef":"an orthographic camera fitted to the photo's silhouette with the traced section (profiles.front) run along the block and the adjustment screw's head on its face, by Nelder-Mead from the best of a grid of directions (.cache/batch15/slr-sentry-7-gas-block/silfit3.py): the lens toward (0.621, 0.506, 0.599) in the part frame, 543.4 px/in, IoU 0.980","method":"the three flutes' lower ends taken back onto the section's surface: 0.328, 0.437, 0.387 (where each runs out into the foot's flank)","via":"harvest"}}]},"pin_hole_from_front":{"label":"The roll pin's cross hole behind the front face","kind":"length","measurements":[{"id":"photo-right","value":0.262,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block b5a6b18f895e (Primary Arms SA7-SM_00: the block from the right, ahead and above, with its roll pin and key, 2200 x 1467)","scaleRef":"an orthographic camera fitted to the photo's silhouette with the traced section (profiles.front) run along the block and the adjustment screw's head on its face, by Nelder-Mead from the best of a grid of directions (.cache/batch15/slr-sentry-7-gas-block/silfit3.py): the lens toward (0.621, 0.506, 0.599) in the part frame, 543.4 px/in, IoU 0.980","method":"the hole's middle (735, 355) taken back onto the boss's right side","via":"harvest"}},{"id":"photo-left","value":0.175,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block 8a7811f1e180 (Primary Arms SA7-SM_01: the block from the left, ahead and above, 2200 x 1467)","scaleRef":"the same fit: the lens toward (0.766, 0.482, -0.427), 738.9 px/in, IoU 0.978","method":"the hole's middle (1130, 450) taken back onto the boss's left side","via":"harvest"}}],"adopt":{"from":"photo-right","reason":"The right photo is the squarer of the two to the side the hole is on (the lens 37 degrees off the side's normal against 55); the patent's proportion, 0.268 at this length, is beside it."},"note":"The patent's FIG. 7 has it 0.305 behind the front face of a block 0.974 long."},"tube_hole_above_bore":{"label":"The gas tube's hole, its axis above the bore (at the block)","kind":"length","measurements":[{"id":"patent","value":0.674,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block e33823945e77 (US 9,410,756 sheet 3, the patent office's PDF page 4: FIG. 3 the block from its front, FIG. 4 from its rear, orthographic, 2560 x 3300)","scaleRef":"FIG. 3's bore, a least-squares circle through its stroke (centre (1288.1, 2218.8), radius 243.1 px, rms 1.0 px), as the journal's .750: 648.3 px/in; FIG. 4 is on the same sheet at the same size (its bore 243.9 px)","method":"FIG. 4's channel 6, a least-squares circle (centre (851.1, 1186.2), radius 58.6 px inside a chamfer of 64.8, rms 0.6): 436.9 px above the bore's centre","via":"harvest"}}],"note":"No photo on file shows the rear face. The patent's figure, 0.049 above the Army's .625 for a front sight."},"tube_hole_d":{"label":"The gas tube's hole, diameter","kind":"length","measurements":[{"id":"tdp","value":0.1805,"unit":"in","pm":0.001,"source":{"type":"derived","expr":"{bcm-750-gas-block.tube_hole_d}"},"note":"The Army's hole for the .180 tube (drawing 8448566, as the BCM block's ledger cites it). SLR: 'USES STANDARD GAS TUBE'."},{"id":"patent","value":0.181,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block e33823945e77 (US 9,410,756 sheet 3, the patent office's PDF page 4: FIG. 3 the block from its front, FIG. 4 from its rear, orthographic, 2560 x 3300)","scaleRef":"FIG. 3's bore, a least-squares circle through its stroke (centre (1288.1, 2218.8), radius 243.1 px, rms 1.0 px), as the journal's .750: 648.3 px/in","method":"FIG. 4's channel 6, 117.2 px across inside its chamfer","via":"harvest"}}],"adopt":{"from":"tdp","reason":"It takes the standard tube; the patent's circle is the same."}},"pin_hole_d":{"label":"The gas tube's roll pin: its cross hole, diameter","kind":"length","measurements":[{"id":"tdp","value":0.078,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{bcm-750-gas-block.pin_hole_d}"},"note":"The Army's hole for the gas tube's pin (drawing 8448566, as the BCM block's ledger cites it): the block takes the standard tube and its pin is in the box ('Tool, roll pin and mounting screws included')."}]},"pin_to_port":{"label":"The gas tube's pin hole to its gas hole","kind":"length","measurements":[{"id":"tdp","value":0.418,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{bcm-750-gas-block.pin_to_port}"},"note":"The Army's gas tube (drawing 8448567, as the BCM block's ledger cites it): the tube this block takes."}]},"tube_hole_past_pin":{"label":"How far the gas tube's hole runs on ahead of the pin's hole","kind":"length","measurements":[{"id":"tdp","value":0.217,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{bcm-750-gas-block.tube_hole_past_pin}"},"note":"Not seen: the Army's sight's depth (drawing 8448566, as the BCM block's ledger cites it), not this block's."}]},"port_from_rear":{"label":"Its gas port ahead of its rear face","kind":"length","measurements":[{"id":"derived","value":0.176,"unit":"in","pm":0.07,"source":{"type":"derived","expr":"{slr-sentry-7-gas-block.length} - {slr-sentry-7-gas-block.pin_hole_from_front} - {slr-sentry-7-gas-block.pin_to_port}"}}],"note":"Not published; the port is inside. Where the standard tube's gas hole lands with its pin in the block's cross hole. The part's frame is here."},"pin_hole_above_bore":{"label":"The roll pin's cross hole, its axis above the bore","kind":"length","measurements":[{"id":"tube","value":0.674,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{slr-sentry-7-gas-block.tube_hole_above_bore}"},"note":"The pin crosses the tube through the tube's own hole: at its axis."},{"id":"photo-right","value":0.699,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block b5a6b18f895e (Primary Arms SA7-SM_00: the block from the right, ahead and above, with its roll pin and key, 2200 x 1467)","scaleRef":"an orthographic camera fitted to the photo's silhouette with the traced section (profiles.front) run along the block and the adjustment screw's head on its face, by Nelder-Mead from the best of a grid of directions (.cache/batch15/slr-sentry-7-gas-block/silfit3.py): the lens toward (0.621, 0.506, 0.599) in the part frame, 543.4 px/in, IoU 0.980","method":"the hole's middle taken back onto the boss's right side","via":"harvest"}},{"id":"photo-left","value":0.717,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block 8a7811f1e180 (Primary Arms SA7-SM_01: the block from the left, ahead and above, 2200 x 1467)","scaleRef":"the same fit: the lens toward (0.766, 0.482, -0.427), 738.9 px/in, IoU 0.978","method":"the hole's middle taken back onto the boss's left side","via":"harvest"}}],"adopt":{"from":"tube","reason":"The pin goes through the tube; the photos, both from above, read its hole 0.03 to 0.04 higher, inside their ±."}},"set_screw_front_from_front":{"label":"The front set screw behind the front face","kind":"length","measurements":[{"id":"photo-left","value":0.252,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block 8a7811f1e180 (Primary Arms SA7-SM_01: the block from the left, ahead and above, 2200 x 1467)","scaleRef":"the same fit: the lens toward (0.766, 0.482, -0.427), 738.9 px/in, IoU 0.978","method":"the nearer of the two holes in the bore's floor, its middle (1030, 1100) taken back onto the bore's surface (0.366 under the axis there: the floor is 0.375)","via":"harvest"}}],"note":"The farther hole is half hidden by the front face's rim; its visible middle reads 0.29 behind this one, not the published .400. The rear screw is .400 behind this (SLR: 'There is no difference in the blocks just the front set screw location')."},"set_screw_d":{"label":"The set screws' holes, diameter","kind":"length","measurements":[{"id":"patent","value":0.147,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block e33823945e77 (US 9,410,756 sheet 3, the patent office's PDF page 4: FIG. 3 the block from its front, FIG. 4 from its rear, orthographic, 2560 x 3300)","scaleRef":"FIG. 3's bore, a least-squares circle through its stroke (centre (1288.1, 2218.8), radius 243.1 px, rms 1.0 px), as the journal's .750: 648.3 px/in","method":"the hole's mouth in the bore's floor in FIG. 3, 95 px across","via":"harvest"}},{"id":"photo-left","value":0.17,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block 8a7811f1e180 (Primary Arms SA7-SM_01: the block from the left, ahead and above, 2200 x 1467)","scaleRef":"the same fit: the lens toward (0.766, 0.482, -0.427), 738.9 px/in, IoU 0.978","method":"the nearer hole's mouth across the block, 125 px at 738.9 px/in","via":"harvest"}}],"adopt":{"from":"patent","reason":"The patent's view is square across the hole; the photo's reading is of a mouth in a curved floor, inside its ±."}},"set_screw_length":{"label":"The set screws' length","kind":"length","measurements":[{"id":"assumed","value":0.15,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no page gives the screws' size; as long as the foot is deep under the bore (0.173 in) less what is left for the key, so that it ends inside the flat.","via":"harvest"}}]},"spring_rear_from_front":{"label":"The flat spring's screw behind the front face","kind":"length","measurements":[{"id":"photo-right","value":0.771,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block b5a6b18f895e (Primary Arms SA7-SM_00: the block from the right, ahead and above, with its roll pin and key, 2200 x 1467)","scaleRef":"an orthographic camera fitted to the photo's silhouette with the traced section (profiles.front) run along the block and the adjustment screw's head on its face, by Nelder-Mead from the best of a grid of directions (.cache/batch15/slr-sentry-7-gas-block/silfit3.py): the lens toward (0.621, 0.506, 0.599) in the part frame, 543.4 px/in, IoU 0.980","method":"the button head's middle (500, 390) taken back onto the flat (z 0.27)","via":"harvest"}}],"note":"SLR: 'Stamped Alloy Flat Spring with 1400deg temper' and a 'Melonite finish 4140 detent plunger': the spring is held by its screw at the rear and bears on the plunger at its front end (the patent's spring 19, screw 20 and plunger 21)."},"spring_front_from_front":{"label":"The flat spring's front end behind the front face","kind":"length","measurements":[{"id":"photo-right","value":0.094,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block b5a6b18f895e (Primary Arms SA7-SM_00: the block from the right, ahead and above, with its roll pin and key, 2200 x 1467)","scaleRef":"an orthographic camera fitted to the photo's silhouette with the traced section (profiles.front) run along the block and the adjustment screw's head on its face, by Nelder-Mead from the best of a grid of directions (.cache/batch15/slr-sentry-7-gas-block/silfit3.py): the lens toward (0.621, 0.506, 0.599) in the part frame, 543.4 px/in, IoU 0.980","method":"the spring's rounded tip (768, 497) taken back onto the flat","via":"harvest"}}]},"spring_height_front":{"label":"The flat spring's height at its front end","kind":"length","measurements":[{"id":"photo-front","value":0.115,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block 276bd13fbaaf (SLR's own photo, DSC01311: the front face nearly square on, yawed about 20 degrees to show the right side, 2770 x 1847)","scaleRef":"the bore's opening, an ellipse fitted to the edge of the bright bore inside the black face (482.1 px tall): 642.9 px/in up the face, which up the right side's flat (turned 70 degrees to the face, about the vertical) is the same","method":"its upper and lower edges a little behind its tip (column 1290): rows 688 and 762, 74 px","via":"harvest"}},{"id":"photo-right","value":0.099,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block b5a6b18f895e (Primary Arms SA7-SM_00: the block from the right, ahead and above, with its roll pin and key, 2200 x 1467)","scaleRef":"an orthographic camera fitted to the photo's silhouette with the traced section (profiles.front) run along the block and the adjustment screw's head on its face, by Nelder-Mead from the best of a grid of directions (.cache/batch15/slr-sentry-7-gas-block/silfit3.py): the lens toward (0.621, 0.506, 0.599) in the part frame, 543.4 px/in, IoU 0.980","method":"its upper and lower edges 0.15 in behind the tip taken back onto the flat: 0.538 and 0.439 above the bore","via":"harvest"}}],"adopt":{"from":"photo-front","reason":"The maker's photo, as for the spring's height round its screw; the two readings agree within their ±."}},"spring_screw_head_d":{"label":"The flat spring's screw, its button head's diameter","kind":"length","measurements":[{"id":"photo-right","value":0.12,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block b5a6b18f895e (Primary Arms SA7-SM_00: the block from the right, ahead and above, with its roll pin and key, 2200 x 1467)","scaleRef":"an orthographic camera fitted to the photo's silhouette with the traced section (profiles.front) run along the block and the adjustment screw's head on its face, by Nelder-Mead from the best of a grid of directions (.cache/batch15/slr-sentry-7-gas-block/silfit3.py): the lens toward (0.621, 0.506, 0.599) in the part frame, 543.4 px/in, IoU 0.980","method":"the head's round, 65 px across where the fit's scale on the flat is 543 px/in","via":"harvest"}}]},"spring_height_rear":{"label":"The flat spring's height round its screw","kind":"length","measurements":[{"id":"photo-front","value":0.198,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block 276bd13fbaaf (SLR's own photo, DSC01311: the front face nearly square on, yawed about 20 degrees to show the right side, 2770 x 1847)","scaleRef":"the bore's opening, an ellipse fitted to the edge of the bright bore inside the black face (482.1 px tall): 642.9 px/in up the face, which up the right side's flat (turned 70 degrees to the face, about the vertical) is the same","method":"its upper and lower edges just ahead of its screw's head (column 1170): rows 668 and 795, 127 px","via":"harvest"}},{"id":"photo-right","value":0.22,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block b5a6b18f895e (Primary Arms SA7-SM_00: the block from the right, ahead and above, with its roll pin and key, 2200 x 1467)","scaleRef":"the orthographic camera fitted to its silhouette (see length)","method":"its upper and lower edges 0.06 ahead of its screw taken back onto the flat: 0.610 and 0.387 above the bore","via":"harvest"}}],"adopt":{"from":"photo-front","reason":"The maker's photo, its scale the bore's; Primary Arms' reads it 0.02 taller through a fitted camera, inside both ±."}},"spring_thickness":{"label":"The flat spring's thickness","kind":"length","measurements":[{"id":"assumed","value":0.025,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows the spring edge on.","via":"harvest"}}]},"spring_above_bore":{"label":"The flat spring's middle above the bore's axis","kind":"length","measurements":[{"id":"photo-front","value":0.515,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block 276bd13fbaaf (SLR's own photo, DSC01311: the front face nearly square on, yawed about 20 degrees to show the right side, 2770 x 1847)","scaleRef":"the bore's opening, an ellipse fitted to the edge of the bright bore inside the black face (482.1 px tall): 642.9 px/in up the face, which up the right side's flat (turned 70 degrees to the face, about the vertical) is the same","method":"the middle of its two edges at its rear (731.5) and near its tip (725), 330.8 and 337.3 px above the bore's centre (row 1062.3); the right side stands 0.24 in off the face's plane, which a level lens doesn't move up or down","via":"harvest"}},{"id":"photo-right","value":0.49,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/slr-sentry-7-gas-block b5a6b18f895e (Primary Arms SA7-SM_00: the block from the right, ahead and above, with its roll pin and key, 2200 x 1467)","scaleRef":"an orthographic camera fitted to the photo's silhouette with the traced section (profiles.front) run along the block and the adjustment screw's head on its face, by Nelder-Mead from the best of a grid of directions (.cache/batch15/slr-sentry-7-gas-block/silfit3.py): the lens toward (0.621, 0.506, 0.599) in the part frame, 543.4 px/in, IoU 0.980","method":"the middle of its edges at the front (0.538, 0.439) and the screw's middle (0.477)","via":"harvest"}}],"adopt":{"from":"photo-front","reason":"The maker's photo; it puts the spring on the middle of the patent's flat (0.505), Primary Arms' through its fitted camera 0.025 lower."},"note":"The flat it lies on is the patent's (FIG. 3's outline has it on the part's right from 0.452 to 0.557 above the bore, 0.239 out from the centre line)."},"edge_break":{"label":"The edges' break","kind":"length","measurements":[{"id":"assumed","value":0.008,"unit":"in","pm":0.004,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: every edge in the photos shows a small break; its size isn't read.","via":"harvest"}}]},"spring_flat_margin":{"label":"How far the flat under the spring reaches beyond the spring's edge","kind":"length","measurements":[{"id":"assumed","value":0.012,"unit":"in","pm":0.008,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the spring is taller round its screw (0.198) than the patent's flat (0.105), and the photos show it lying flat on the side with a narrow lit border; the flat is drawn as far as the spring reaches and this much more.","via":"harvest"}}]}}},{"subject":"spikes-tactical-sdr100a","title":"Spike's Tactical Delta Ring Assembly w/Mil-Spec Barrel Nut (SDR100A)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"spikes","value":2.5,"unit":"oz","pm":0.05,"stated":"Weight: 2.5oz","source":{"type":"spec","publisher":"manufacturer","name":"Spike's Tactical, Delta Ring Assembly w/Mil-Spec Barrel Nut (SDR100A): Specs","url":"https://www.spikestactical.com/collections/parts/delta-ring-assembly-w-mil-spec-barrel-nut/","retrieved":"2026-10-28","via":"harvest"}},{"id":"metal","value":2.66,"unit":"oz","pm":0.2,"source":{"type":"derived","expr":"{bcm-gi-barrel-nut.weight} + {bcm-delta-ring-assembly.weight}","via":"harvest"},"note":"A check, not a reading on Spike's parts: the mil-spec nut, ring, weld spring and snap ring worked out from their sizes as steel and 7075 (the two BCM parts' figures, which are those sizes' and nothing of BCM's own). 0.16 oz (6%) over Spike's figure, inside the two figures' ±."}],"adopt":{"from":"spikes","reason":"The maker's own figure for this product; the mil-spec pieces' metal worked out from their sizes agrees within its ±."},"note":"The four pieces together."},"length":{"label":"Length along the bore","kind":"length","measurements":[{"id":"standard","value":0.85,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.ar15.barrel_nut_length}","via":"harvest"}}],"note":"The nut's. Spike's states none: \"fully Mil-Spec\", the mil-spec nut's. Its front photo has the ring's front flush with the nut's flange, as the Army's assembly (8448711) has them with the ring forward on its spring."},"flange_diameter":{"label":"Its toothed flange's outside diameter","kind":"length","measurements":[{"id":"standard","value":1.56,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{std.ar15.barrel_nut_flange_od}","via":"harvest"},"note":"The mil-spec nut's; Spike's states none."}]},"ring_outside_diameter":{"label":"The delta ring's largest outside diameter (its rear land)","kind":"length","measurements":[{"id":"standard","value":2.1,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.ar15.slip_ring_od}","via":"harvest"},"note":"The Army's drawing's (8448712); Spike's: \"The delta ring itself is made of Mil-Spec aluminum\"."}]},"notches":{"label":"The notches round the nut's flange","kind":"count","measurements":[{"id":"standard","value":20,"unit":"count","pm":0,"source":{"type":"derived","expr":"{std.ar15.barrel_nut_notches}","via":"harvest"}}],"note":"Spike's front photo (b8505e770f0f) shows the whole flange inside the ring's skirt, an oblique from in front and above: along its lower arc, where the round is seen least foreshortened, the notches come every 85 px on a flange 585 px across, a twentieth of its round (1838 px). Not counted one by one round the far side, where the teeth crowd."},"ring_lands":{"label":"The lands round the delta ring's outside","kind":"count","measurements":[{"id":"photo","value":7,"unit":"count","pm":0,"source":{"type":"photo","photo":"references/spikes-tactical-sdr100a b8505e770f0f (Spike's front photo, 2000 px)","scaleRef":"none (a count)","method":"counted down the ring's near side, below the skirt's front face: six dark step lines, seven lit lands","via":"harvest"}},{"id":"standard","value":7,"unit":"count","pm":0,"source":{"type":"derived","expr":"{std.ar15.slip_ring_steps} + 1","via":"harvest"}}],"adopt":{"from":"standard","reason":"The drawing's six steps; Spike's photo has the same count."}}}},{"subject":"std","title":"Interface standards","dimensions":{"ar15.pin_spacing":{"label":"AR-15 takedown-to-pivot pin spacing","kind":"length","measurements":[{"id":"std","value":6.375,"unit":"in","source":{"type":"standard","doc":"AR-15 receiver interface (TDP)","via":"brief"},"note":"A rail-calibrated Workhorse photo agreed to within 0.05% (brief)."}]},"ar15.trigger_guard_hole_spacing":{"label":"AR-15 trigger guard holes, rear to front (centre to centre)","kind":"length","measurements":[{"id":"tdp","value":1.844,"unit":"in","pm":0.003,"source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: side elevation, dimensions from the pivot pin; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"},"note":"1.844 ± .003 (bottom chain)"}]},"ar15.trigger_guard_front_x":{"label":"AR-15 trigger guard front hole, X (from the takedown pin)","kind":"length","measurements":[{"id":"tdp","value":3.3425,"unit":"in","pm":0.007,"source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: side elevation, dimensions from the pivot pin; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"},"note":"6.375 ± .002 minus 3.0325 ± .0050 (front hole to the pivot pin); a 0.125 in hole on the right side only"}]},"ar15.trigger_guard_rear_x":{"label":"AR-15 trigger guard rear hole, X (from the takedown pin)","kind":"length","measurements":[{"id":"tdp","value":1.4985,"unit":"in","pm":0.01,"source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: side elevation, dimensions from the pivot pin; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"},"note":"front hole minus 1.844 ± .003; the 0.1275 in roll-pin hole through both sides"}]},"ar15.trigger_guard_rear_y":{"label":"AR-15 trigger guard rear hole, Y (below the pin line)","kind":"length","measurements":[{"id":"tdp","value":-2.18,"unit":"in","pm":0.01,"source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: side elevation, dimensions from the pivot pin; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"},"note":"2.18 below the takedown pin (two-place: ± .01)"}]},"ar15.selector_x":{"label":"AR-15 safety selector hole, X (from the takedown pin)","kind":"length","measurements":[{"id":"tdp","value":0.803,"unit":"in","pm":0.004,"source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: side elevation, dimensions from the pivot pin; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"},"note":"6.375 minus 5.572 REF; also hammer pin minus 1.968 ± .0015"}]},"ar15.selector_y":{"label":"AR-15 safety selector hole, Y (below the pin line)","kind":"length","measurements":[{"id":"workhorse","value":-0.466,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{bad-workhorse-lower.selector_y}","via":"harvest"},"note":"A forged mil-spec lower: its selector hole is the standard's."}],"note":"Drawing 8448608 dimensions the fire-control holes' heights in a chain we couldn't tie to the pin line on the scan (M5), so this comes from the Workhorse, whose two independent photos agree; replace it with the TDP ordinate once that chain is read."},"ar15.mag_catch_x":{"label":"AR-15 magazine catch hole (the release button's axis), X (from the takedown pin)","kind":"length","measurements":[{"id":"tdp","value":3.291,"unit":"in","pm":0.004,"stated":".204 DIA +.003 THRU / .312 DIA +.004 CBORE at 3.084 ± .003 from the pivot pin","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P (read by the M5 research agent); user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p63","via":"user"},"note":"6.375 − 3.084."},{"id":"photo","value":3.3,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/rise-lpk a37f831793fa (US Marine Corps: M4A1 SOPMOD Block II, straight right side, 7607 px; public domain)","scaleRef":"pin frame from Hough-fitted pin heads: takedown (2303.5, 1092.5), pivot (3478.5, 1078.5) = (0, 0), (6.375, 0): 184.3 px/in","method":"the button outline's centre on a 4x crop (px 2912.9, 1189.4)","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The standard; the USMC photo agrees within 0.01."}},"ar15.mag_catch_y":{"label":"AR-15 magazine catch hole, Y","kind":"length","measurements":[{"id":"photo","value":-0.565,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/rise-lpk a37f831793fa (US Marine Corps: M4A1 SOPMOD Block II, straight right side, 7607 px; public domain)","scaleRef":"pin frame from Hough-fitted pin heads: takedown (2303.5, 1092.5), pivot (3478.5, 1078.5) = (0, 0), (6.375, 0): 184.3 px/in","method":"the button outline's centre on a 4x crop, perpendicular to the pin line (tilted −0.68°)","via":"harvest"}}],"note":"A public redraw of the lower (eformance.com ar15_receiver.pdf, 'drawn from Colt redraw dated 2-14-93') puts it about −0.56 (the research agent's reading, not re-checked); two more USMC photos (M16A2, M16A4) read −0.54 and −0.56."},"ar15.hammer_pin_x":{"label":"AR-15 hammer pin hole, X (from the takedown pin)","kind":"length","measurements":[{"id":"tdp","value":2.771,"unit":"in","pm":0.004,"source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: side elevation, dimensions from the pivot pin; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"},"note":"6.375 ± .002 minus 3.604 ± .002"}]},"ar15.trigger_pin_x":{"label":"AR-15 trigger pin hole, X (from the takedown pin)","kind":"length","measurements":[{"id":"tdp","value":1.928,"unit":"in","pm":0.004,"source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: side elevation, dimensions from the pivot pin; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"},"note":"hammer pin minus .8430 ± .0015"}]},"ar15.magwell_length":{"label":"AR-15 magazine well, inside front to back (with the rear spine slot)","kind":"length","measurements":[{"id":"tdp","value":2.553,"unit":"in","pm":0.007,"source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 2 of 2, rev P: Section F-F (the magazine well, sheet 1 zone B-4); user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p63","via":"user"},"note":"2.553 REF = the rear slot's .155 ± .002 + the box's 2.398 (title-block ± .005)"}]},"ar15.magwell_box_length":{"label":"AR-15 magazine well, inside front to back (the box ahead of the spine slot)","kind":"length","measurements":[{"id":"tdp","value":2.398,"unit":"in","pm":0.005,"source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 2 of 2, rev P: Section F-F (the magazine well, sheet 1 zone B-4); user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p63","via":"user"},"note":"2.398, title-block tolerance (3-place decimals ± .005)"}]},"ar15.magwell_wall_lean":{"label":"AR-15 magazine well, front and rear walls' lean from square to the receiver's top","kind":"angle","measurements":[{"id":"tdp","value":0,"unit":"deg","pm":1,"source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 2 of 2, rev P: Section A-A (the well's front and rear walls drawn square to the top; no angle dimensioned, so the title block's angle tolerance ± 1° applies); user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p63","via":"user"}}],"note":"What holds a seated magazine's straight top section upright: a traced magazine is turned until that section's edges lean this much."},"ar15.magwell_width":{"label":"AR-15 magazine well, inside width","kind":"length","measurements":[{"id":"tdp","value":0.898,"unit":"in","pm":0.005,"source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 2 of 2, rev P: Section F-F (the magazine well, sheet 1 zone B-4); user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p63","via":"user"},"note":".898 between datums K and Z (the side walls' inner faces), title-block ± .005"}]},"ar15.lower_body_width":{"label":"AR-15 lower receiver body width (outside, across the upper's lug slot)","kind":"length","measurements":[{"id":"tdp","value":0.88,"unit":"in","pm":0.008,"stated":".690 ± .004 from the inside face of one front-lug ear (datum AH) to the other's outside face; the lug slot .500 REF","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 2 of 2, rev P: Section C-C; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p63","via":"user"},"note":"2 × (.690 − .500 / 2): the slot is centred on the receiver. The bolt catch's bosses stand out to .868 from AH on the left."}]},"ar15.bolt_catch_boss_out":{"label":"AR-15 bolt catch bosses' outside face, from the receiver's centre (left side)","kind":"length","measurements":[{"id":"tdp","value":0.618,"unit":"in","pm":0.006,"stated":".868 ± .003 from the inside face of the front lug's ear (datum AH); the lug slot .500 REF","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 2 of 2, rev P: Section C-C; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p63","via":"user"},"note":".868 − .500 / 2: 0.178 proud of the body's face (std.ar15.lower_body_width / 2 = 0.44)."},{"id":"model","value":0.7274,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its planar faces read from the STEP text (.cache/fence/step.py), in the rifle frame set by its pin holes: the two faces either side of the catch's slot (X 3.106 to 3.220 and 3.376 to 3.508, Y 0 to 0.118) at 0.7274 from the centre","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing, read again 2026-10-03 (D49 asked for it): from the same datum (AH, the inside face of the front lug's right ear) its .690 ± .004 lands on the body's left face at 0.44, the TDP's 0.88 body, so AH is read right and the bosses' face is .868 − .250 = 0.618. The model has them 0.11 further out: the model's own."}},"ar15.magwell_outside_width":{"label":"AR-15 magazine well, outside width (its walls)","kind":"length","measurements":[{"id":"tdp","value":1.098,"unit":"in","pm":0.01,"stated":".898 REF inside; walls .10 BOTH SIDES","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 2 of 2, rev P: Section C-C; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p63","via":"user"},"note":".898 + 2 × .10. The lip at the well's mouth flares wider (.375 R TRUE REF), not dimensioned."}]},"ar15.buffer_tower_od":{"label":"AR-15 buffer tower ring, outside diameter","kind":"length","measurements":[{"id":"tdp","value":1.392,"unit":"in","pm":0.01,"stated":"1.325 from datum S to the ring's top; .629 BASIC from S to its centre","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: Section B-B; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"},"note":"2 × (1.325 − .629). Datum S is the deck (std.ar15.deck_y): the Workhorse's two side photos put the ring's top 1.543 and 1.537 above the pin line against 1.5735 here (std.ar15.buffer_tower_top_y), short as what stands behind the near face reads from 24 in with the lens 3 in below it."}]},"ar15.deck_y":{"label":"AR-15 lower receiver, top deck (where the upper sits), Y above the pin line","kind":"length","measurements":[{"id":"tdp","value":0.2485,"unit":"in","pm":0.0015,"stated":".250 -.003 FROM CL OF -V- AND -AC-","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: side elevation, at the pivot pin; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"},"note":"-V- is the takedown pin's hole and -AC- the pivot pin's: the receiver's top surface above the line through them (.247 to .250; the middle here). The upper's drawing (8448524 sheet 1) puts its lug holes .251 +.003 below its underside, which sits on this. The Workhorse's two side photos read 0.254 and 0.247."}]},"ar15.deck_front_x":{"label":"AR-15 lower receiver, the deck's front end (where its top turns down over the pivot lug's ears), X (from the takedown pin)","kind":"length","measurements":[{"id":"model","value":6.194,"unit":"in","pm":0.01,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"the one plane at Y 0.250 in the frame the model's pin holes set, over X 0.126 to 6.194 and Z -0.599 to 0.540: it begins where the rear walls' arc runs out and ends where the ears' top is rounded over (free-form faces from X 6.08 to 6.30, down to Y 0.20) (.cache/rear-walls/step.py, 2026-10-12)","via":"user"},"note":"The Army's drawing gives the deck's height (std.ar15.deck_y) and, on the sheets on file, not where it ends."}],"note":"How far forward the deck is drawn as the plane an upper sits on (pipeline/blender/lib.py deck_outline, 2026-10-12). The lowers' own outlines turn down a little short of it: the Workhorse's at 6.141, Bear Creek's at 6.107, and Aero's, whose outline is two straight stretches there, as early as 5.926, which under an upper's flat underside was a wedge of backdrop a fifth of an inch long behind the upper's front lug."},"ar15.bore_axis_y":{"label":"AR-15 bore and receiver extension axis, Y above the pin line","kind":"length","measurements":[{"id":"tdp-lower","value":0.8775,"unit":"in","pm":0.0015,"stated":".629 BASIC from datum S to the threaded hole's centre","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: Section B-B; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"},"note":"Datum S is the top of the walls either side of the front lug's slot, which the section cuts: the deck (std.ar15.deck_y, .250 −.003 above the pins). .629 + .2485."},{"id":"tdp-upper","value":0.8775,"unit":"in","pm":0.0035,"stated":".625 ± .002 from the bore's centre line (AB) to datum T; lug holes .251 +.003 below the underside","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), rev G: sheet 2 of 2, View F-F, and sheet 1 of 2, side elevation; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p109, p108","via":"user"},"note":"Datum T is the receiver's flat underside in View F-F (the front lug hangs below it). .625 + .2525."}],"adopt":{"from":"tdp-lower","reason":"The lower's and the upper's drawings give the same height from either side of the joint; the lower's is the tighter."},"note":"One line: the bolt carrier runs from the upper's bore into the receiver extension. M2 had 0.849 from a side photo, and the Workhorse's own photos agreed (its tower's top at 1.54): both read the mid-plane against a scale taken from the pins' near ends, 0.44 in nearer the lens, which from about 30 in is 0.03 short at that height. Photos read since agree with the drawings within their ±: the Aero lower's castle nut centres 0.89 above the pin line (bcm-end-plate.top_above_axis), and Magpul's two pictures of an M4 put the tube's axis 0.90 and 0.93 above the takedown pin's head (± 0.03: the head's dark blob takes in its shadow below)."},"ar15.buffer_tower_top_y":{"label":"AR-15 buffer tower ring, top, Y above the pin line","kind":"length","measurements":[{"id":"tdp","value":1.5735,"unit":"in","pm":0.0065,"stated":"1.325 from datum S to the ring's top","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: Section B-B; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"},"note":"1.325 (three-place: ± .005) above the deck (std.ar15.deck_y). The axis plus the ring's radius is the same height (std.ar15.bore_axis_y + std.ar15.buffer_tower_od / 2)."}]},"ar15.receiver_rear_x":{"label":"AR-15 lower receiver, rear face (the buffer tower's, where the end plate bears), X (from the takedown pin)","kind":"length","measurements":[{"id":"tdp","value":-1.125,"unit":"in","pm":0.005,"stated":"7.503 -.006","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: side elevation, dimensions from the pivot pin; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"},"note":"7.503 −.006 from the pivot pin to the rear face (7.497 to 7.503; the middle here), less the pins' 6.375 ± .002. The Workhorse's rear face below the ring reads 1.134 and 1.136 in its two side photos; the ring's rim, 0.25 in nearer the lens than the pins they are scaled by, 1.162 and 1.147."}]},"ar15.buffer_tower_front_x":{"label":"AR-15 buffer tower ring, front face (where the upper's rear meets it), X (from the takedown pin)","kind":"length","measurements":[{"id":"tdp","value":-0.628,"unit":"in","pm":0.005,"stated":"7.000 +.006","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: side elevation, dimensions from the pivot pin; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"},"note":"7.000 +.006 from the pivot pin (the middle here), less 6.375 ± .002: the ring is 0.497 thick. Section A-A (sheet 2) draws its hatched front face on this line. The upper's drawing (8448524 sheet 1) has its rear face 6.999 −.006 behind its pivot hole: it stops just ahead of this face. The Workhorse's side photos show the tower's side walls running 0.31 further forward (bad-workhorse-lower.tower_front_x)."}]},"ar15.upper_front_face_x":{"label":"AR-15 upper receiver, front face (the end of its barrel-nut thread, where a barrel extension's flange seats), X (from the takedown pin)","kind":"length","measurements":[{"id":"tdp","value":7.036,"unit":"in","pm":0.005,"stated":".661 ± .003","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: side elevation, dimensions from the pivot lug's hole; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108 (crop-upper-front-end-dims.png)","via":"user"},"note":".661 ± .003 from the pivot lug's hole forward to the receiver's front end, which is the end of the threaded nose (the drawing's rightmost line), plus the pins' 6.375 ± .002."}]},"ar15.upper_rear_face_x":{"label":"AR-15 upper receiver, rear face, X (from the takedown pin)","kind":"length","measurements":[{"id":"tdp","value":-0.621,"unit":"in","pm":0.005,"stated":"6.999 -.006","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: side elevation, dimensions from the pivot lug's hole; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108 (crop-upper-front-end-dims.png)","via":"user"},"note":"6.999 −.006 from the rear face to the pivot lug's hole (6.993 to 6.999; the middle here), less the pins' 6.375 ± .002. It stops just ahead of the lower's buffer tower (std.ar15.buffer_tower_front_x, −0.628)."}]},"ar15.rear_wall_arc_r":{"label":"AR-15 lower receiver, the arc its two rear walls rise along from the deck to the buffer tower's front face (what an upper's rear lower corner sits over), radius","kind":"length","measurements":[{"id":"tdp","value":0.75,"unit":"in","pm":0.005,"stated":".750 R","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: side elevation, ahead of the buffer tower; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"},"note":"A leader from a centre mark above the takedown pin to the arc that leaves the tower's front face and runs out on the deck. No centre is dimensioned: tangent to both as drawn, it is this radius ahead of the face (std.ar15.buffer_tower_front_x) and above the deck (std.ar15.deck_y), X 0.122 and Y 0.9985. A second line 0.09 in outside the arc, which runs on below the deck to the takedown pin's spotface, is the forging's blend into the body and not this arc. Title-block ± .005."},{"id":"model","value":0.75,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"two cylindrical faces, one each side, of radius 19.05 mm about an axis across the receiver through X 0.1260, Y 1.0000 in the frame the model's pin holes set, over X -0.624 to 0.126 and Y 0.250 to 1.000, from Z ±0.236 out to ±0.680: tangent to the model's own deck (0.250) and tower face (-0.624) (.cache/rear-walls/step.py, 2026-10-12)","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's; the reference model has the same radius, about the centre the drawing's two faces give."},"note":"Looked at on two real parts, at points picked by eye (a check, not a measurement): the Workhorse's right photo (3f26be6b7eb5) has its near wall's edge within 0.03 of this arc from the tower's face down to the deck, and the user's own 22RB has its rear lower corner on it within 0.03 at six places in their photo of its left side (fc6a01b62b5a, scaled by the lug's hole)."},"ar15.buffer_trough_r":{"label":"AR-15 lower receiver, the trough between its two rear walls ahead of the buffer tower (the threaded hole's minor radius carried on forward), radius","kind":"length","measurements":[{"id":"tdp","value":0.5625,"unit":"in","pm":0.005,"stated":".5625 REF","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 2 of 2, rev P: Section A-A; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p63","via":"user"},"note":"From the threaded hole's centre line (std.ar15.bore_axis_y) down to the floor line that runs on ahead of the tower's front face, just above the deck. A reference dimension: no tolerance of its own."},{"id":"model","value":0.5625,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"one cylindrical face of radius 14.2875 mm about the buffer's axis, from the rear face (X -1.128) on to X -0.280: the unthreaded model's bore and the trough ahead of it are one surface (.cache/rear-walls/step.py, 2026-10-12)","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's; the reference model has the same."}},"ar15.upper_rear_corner_r":{"label":"AR-15 upper receiver, its rear lower corner (from its rear face down to its underside, over a lower's rear walls), radius","kind":"length","measurements":[{"id":"tdp","value":0.76,"unit":"in","pm":0.005,"stated":".760 R","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: side elevation, at the rear lug; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"},"note":"The arc of the rear lower corner, with no centre dimensioned: drawn tangent to the rear face (std.ar15.upper_rear_face_x) and the underside, so X 0.139 and Y 1.0085 on a lower. A hundredth larger than the walls' arc about a centre 0.02 from theirs: 0.007 clear of the walls at the rear face, 0.009 half way down, and meeting them where both run out on the deck. A callout beside it, 1.16 R REF, is another arc (not identified, not used). Title-block ± .005."},{"id":"model","value":0.75,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"cylindrical faces of radius 19.05 mm about an axis across the receiver through X 0.1250, Y 1.0000 in the frame the model's lug holes set, each side from the rear lug's flank (Z ±0.247) out to ±0.694 and on across the forward assist's housing: the lower's own arc, so the model's two receivers touch all along it (.cache/rear-walls/step.py, 2026-10-12)","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing wins beside the model (D49), which gives its upper the lower's radius and no clearance."},"note":"Not what a part's model is cut to: an upper's model is cut to the lower's own arc (std.ar15.rear_wall_arc_r; pipeline/blender/lib.py upper_rear_corner), so the corner bears on the walls. Drawn at the drawing's 0.007 to 0.009 clear of them, the gap would be a slit of backdrop from one side of the rifle to the other. Expo Arms' upper's left photo shows the arc where the drawing's two faces put it, within 0.03 along its length (read when the part came in, 2026-10-05; the figure was in that part's ledger until 2026-10-12)."},"ar15.upper_barrel_thread_length":{"label":"AR-15 upper receiver, the barrel-nut thread's length (its front face ahead of the body's shoulder)","kind":"length","measurements":[{"id":"tdp","value":0.445,"unit":"in","pm":0.01,"stated":".445 REF","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: side elevation, dimensions from the pivot lug's hole; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108 (crop-upper-front-end-dims.png)","via":"user"},"note":"A reference dimension: from the body's front shoulder, where the 1¼-18 UNEF-2A thread begins, to the front end. A barrel nut and a free-float handguard's rear end come back to that shoulder."}]},"ar15.barrel_tenon_length":{"label":"AR-15 barrel, its tenon: the breech face behind the shoulder a barrel extension's front face seats on","kind":"length","measurements":[{"id":"tdp","value":0.62,"unit":"in","pm":0.001,"stated":".620 ±.001","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2: the main view, dimensioned from the breech end; user-supplied scan (Distribution Statement F, Colt proprietary notice), PDF page 213","via":"user"}}]},"ar15.barrel_extension_length":{"label":"AR-15 barrel extension, its front face (the flange's) to its rear end","kind":"length","measurements":[{"id":"model","value":1.121,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Extension.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"its planes across its axis from the STEP text (mm): the front face at 0, the rear end at 28.4734","via":"user"}}],"note":"The extension's own drawing (8448550) isn't in the package: the reference CAD set stands in (D49), and a drawing would overrule it. A check against the Army's figures: the model's locking lugs' front faces are 0.907 behind its front face, where the barrel's .620 tenon and the assembly drawing's .283 +.006 from the locking face to the breech face (8448548, Section A-A) make .903 to .909."},"ar15.barrel_extension_flange_thickness":{"label":"AR-15 barrel extension, its flange between its two faces (the rear one seats on the receiver's front face)","kind":"length","measurements":[{"id":"model","value":0.131,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Extension.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"its planes across its axis from the STEP text (mm): the front face at 0, the flange's rear face at 3.3274; the flange is its largest cylinder, 1.170 in across","via":"user"}}],"note":"Two barrels' own photos read it 0.095 (bcm-16-mid-barrel.flange_front_x) and 0.19 across its two corners (bca-556-16-mid-barrel.flange_front_x): the model's faces are between them."},"ar15.barrel_extension_behind_breech":{"label":"AR-15 barrel extension, its rear end behind the barrel's breech face","kind":"length","measurements":[{"id":"derived","value":0.501,"unit":"in","pm":0.006,"source":{"type":"derived","expr":"{std.ar15.barrel_extension_length} - {std.ar15.barrel_tenon_length}","via":"user"}}],"note":"What a barrel's length from its breech end is added to for its length end to end, and with the flange what puts its breech behind the receiver's front face (the tenon less the flange: 0.489)."},"ar15.buffer_retainer_x":{"label":"AR-15 buffer retainer hole, X where it breaks the receiver extension's floor (from the takedown pin)","kind":"length","measurements":[{"id":"tdp","value":-0.56,"unit":"in","pm":0.007,"stated":".565 ± .002","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 2 of 2, rev P: Section A-A; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p63","via":"user"},"note":".565 ± .002 forward from the rear face (std.ar15.receiver_rear_x) to the .255 DIA hole's axis at the threaded bore's floor; the hole leans 6°, its top forward. Its axis is 0.07 ahead of the ring's front face (std.ar15.buffer_tower_front_x), which the hole's rear edge cuts into."}]},"ar15.fcg_pocket_front_x":{"label":"AR-15 fire-control pocket, front face X (from the takedown pin)","kind":"length","measurements":[{"id":"tdp","value":3.11,"unit":"in","pm":0.007,"stated":"3.265 from the pivot pin to the pocket front face","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 2 of 2, rev P: Section A-A; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p63","via":"user"},"note":"6.375 − 3.265. The face is the rear of the wall between the pocket and the magazine well; Section A-A scales it 3.126, the plan view 3.26 behind the pivot hole."}]},"ar15.fcg_pocket_length":{"label":"AR-15 fire-control pocket, length (rear wall to front face)","kind":"length","measurements":[{"id":"tdp","value":2.87,"unit":"in","pm":0.01,"stated":"2.87","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 2 of 2, rev P: Section A-A; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p63","via":"user"},"note":"From the pocket rear wall (the face that drops from the rear lug slot floor to the pocket floor) to its front face; the plan view outline scales 2.87 too. Its rear wall is then 0.24 ahead of the takedown pin."}]},"ar15.fcg_pocket_width":{"label":"AR-15 fire-control pocket, width between its inner side faces","kind":"length","measurements":[{"id":"tdp","value":0.69,"unit":"in","pm":0.005,"stated":".690 -L-","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: plan view, zone E-4; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"},"note":"Title-block ± .005. Its right face is .095 ± .003 from the front lug ear inner face (datum AH, .251 off the centre plane), which centres it within 0.002: the side walls are (0.88 − .690) / 2 = 0.095 thick (std.ar15.lower_body_width)."}]},"ar15.fcg_pocket_depth":{"label":"AR-15 fire-control pocket, depth below the deck","kind":"length","measurements":[{"id":"tdp","value":1.249,"unit":"in","pm":0.01,"stated":"1.249 ± .010","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 2 of 2, rev P: Section A-A, zone D-5; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p63","via":"user"},"note":"From the deck (std.ar15.deck_y) to the pocket floor: the floor is 1.0005 below the pin line; Section A-A scales it 1.02. Ahead of the trigger slot the floor is a thin web over the trigger guard opening."}]},"ar15.fcg_pocket_corner_r":{"label":"AR-15 fire-control pocket, its corners seen from above, radius","kind":"length","measurements":[{"id":"tdp","value":0.218,"unit":"in","pm":0.005,"stated":".218 R 5 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: plan view, zone E-3; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"},"note":"The leader lands on the front left corner and the front right is drawn the same; the rear end is drawn rounded, not dimensioned, and taken as the same radius (which five places the callout means is not marked)."}]},"ar15.rear_lug_slot_width":{"label":"AR-15 lower, the upper rear lug slot width","kind":"length","measurements":[{"id":"tdp","value":0.5,"unit":"in","pm":0.005,"stated":".500 ± .005 FOR .63 DEPTH","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: plan view, zone E-5; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"},"note":"Across the slot at the takedown pin, centred (it scales 0.52). The front lug slot is the same .500 (Section C-C, .500 REF)."}]},"ar15.rear_lug_slot_depth":{"label":"AR-15 lower, the upper rear lug slot depth below the deck","kind":"length","measurements":[{"id":"tdp","value":0.63,"unit":"in","pm":0.01,"stated":".63","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 2 of 2, rev P: Section A-A, zone D-6; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p63","via":"user"},"note":"From the deck to the slot floor just ahead of the takedown pin hole: the floor is 0.3815 below the pin line (scales 0.653 below the deck)."}]},"ar15.rear_lug_slot_rear_x":{"label":"AR-15 lower, the upper rear lug slot rear wall X (from the takedown pin)","kind":"length","measurements":[{"id":"tdp","value":-0.402,"unit":"in","pm":0.007,"stated":"6.777 from the pivot pin to the wall behind the takedown pin hole","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 2 of 2, rev P: Section A-A, zone E-5; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p63","via":"user"},"note":"6.375 − 6.777: the vertical face of the buffer tower web. Section A-A scales it −0.371, the plan view −0.406. Forward the slot runs into the pocket rounded rear end (the plan view .765 ± .015 from this wall)."}]},"ar15.trigger_slot_width":{"label":"AR-15 lower, the trigger slot width (through the pocket floor)","kind":"length","measurements":[{"id":"tdp","value":0.312,"unit":"in","pm":0.006,"stated":".312 ± .006 / = L .006 TOTAL; .156 R ± .003","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: plan view, zone E-4; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"},"note":"Centred on the pocket (datum L) within .006, with full round ends (.156 R)."}]},"ar15.trigger_slot_length":{"label":"AR-15 lower, the trigger slot length","kind":"length","measurements":[{"id":"tdp","value":0.68,"unit":"in","pm":0.01,"stated":".68","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 2 of 2, rev P: Section A-A, zone D-5; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p63","via":"user"},"note":"The gap in the hatched floor at the centre plane, end to end. The plan view oblong scales 0.69."}]},"ar15.trigger_slot_front_ahead_of_pin":{"label":"AR-15 lower, the trigger slot front end, ahead of the trigger pin hole","kind":"length","measurements":[{"id":"tdp","value":0.52,"unit":"in","pm":0.01,"stated":".52","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 2 of 2, rev P: Section A-A, zone D-5; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p63","via":"user"},"note":"From the trigger pin hole centre (std.ar15.trigger_pin_x) to the slot front end: X 2.448, the slot from 1.768. The plan view oblong scales 1.756 to 2.450."}]},"ar15.magwell_front_inner_x":{"label":"AR-15 magazine well, front inner face X (from the takedown pin)","kind":"length","measurements":[{"id":"tdp","value":6.025,"unit":"in","pm":0.007,"stated":".350 from the pivot pin back to the front inner wall","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 2 of 2, rev P: Section A-A, zone C-3; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p63","via":"user"},"note":"6.375 − .350 (scales 6.04). The box (std.ar15.magwell_box_length) and the spine slot (std.ar15.magwell_length) run back from it: to 3.627 and 3.472, and Section A-A scales the wall between the pocket and the well 0.362 thick, as 3.265 − .350 − 2.553 says."}]},"ar15.magwell_spine_slot_width":{"label":"AR-15 magazine well, the rear spine slot width","kind":"length","measurements":[{"id":"tdp","value":0.47,"unit":"in","pm":0.006,"stated":".470 = K .006 TOTAL","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 2 of 2, rev P: Section F-F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p63","via":"user"},"note":"The slot behind the box that a magazine spine runs in, .155 ± .002 deep (std.ar15.magwell_length − std.ar15.magwell_box_length), centred on the box (datum K) within .006."}]},"ar15.magwell_corner_r":{"label":"AR-15 magazine well, the box corners seen from above, radius","kind":"length","measurements":[{"id":"tdp","value":0.062,"unit":"in","pm":0.01,"stated":".062 R ± .010 4 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 2 of 2, rev P: Section F-F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p63","via":"user"},"note":"The four corners of the .898 × 2.398 box."}]},"ar15.safety_detent_boss_below_deck":{"label":"AR-15 lower, the safety detent boss inside the pocket, its top below the deck","kind":"length","measurements":[{"id":"tdp","value":0.455,"unit":"in","pm":0.01,"stated":".455 ± .010","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 2 of 2, rev P: Section D-D (cut at the selector, looking forward); user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p63","via":"user"},"note":"The boss stands from the pocket floor on its right wall, at the selector: its top 0.2065 below the pin line. The .125 and .156 detent holes run down through it; their lateral place is not stated as a number, so they are not drawn."}]},"ar15.safety_detent_boss_face":{"label":"AR-15 lower, the safety detent boss face, from the pocket left inner face","kind":"length","measurements":[{"id":"tdp","value":0.53,"unit":"in","pm":0.01,"stated":".530","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: plan view, zone E-5; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"},"note":"The pocket narrowed by the boss: from its left inner face to the boss face (Section D-D scales 0.52): the face 0.185 right of the centre plane."}]},"ar15.safety_detent_boss_from_rear":{"label":"AR-15 lower, the safety detent boss rear end, ahead of the pocket rear wall","kind":"length","measurements":[{"id":"tdp","value":0.36,"unit":"in","pm":0.01,"stated":".36 / .43 / .79 REF","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: plan view, zone E-5; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"},"note":"The chain under the right wall: .36 from the pocket rear end to the boss, .43 the boss (std.ar15.safety_detent_boss_length), .79 REF their sum. It centres the boss on X 0.815 against the selector hole 0.803. Its front end ramps back into the wall (drawn, not dimensioned): drawn square."}]},"ar15.safety_detent_boss_length":{"label":"AR-15 lower, the safety detent boss length","kind":"length","measurements":[{"id":"tdp","value":0.43,"unit":"in","pm":0.01,"stated":".36 / .43 / .79 REF","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: plan view, zone E-5; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"},"note":"The second link of the chain (std.ar15.safety_detent_boss_from_rear)."}]},"ar15.mag_catch_fence_out":{"label":"AR-15 lower, the magazine catch's fence, its face from the centre (right side)","kind":"length","measurements":[{"id":"model","value":0.5404,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its planar and cylindrical faces read from the STEP text (.cache/fence/step.py), in the rifle frame set by its two .251 pin holes (6.376 in apart) and its buffer tower (0.88 above them); the planar face the button's pocket opens through, X 3.023 to 3.566, Y -0.922 to -0.188; the well walls' faces (X 3.578 to 6.087) at the same 0.5404","via":"user"}},{"id":"walls","value":0.549,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.ar15.magwell_outside_width} / 2"},"note":"The TDP's walls, which the model has the fence flush with."}],"adopt":{"from":"walls","reason":"The model has the fence and the walls as one plane (both 0.5404); the walls are the TDP's (.898 inside, .10 each side), so the fence is the walls' face. The model's whole width runs 1.6% under the TDP's here."},"note":"The fence is the raised face around the button's pocket. In the model it and the magazine well walls' outer faces are one plane, so it is the walls' face; the TDP's walls (1.098 across) set it. Forward Controls Design: 'With a TDP spec magazine shaft and magazine release button, the top of the button is usually flush with the fence' (rise-lpk.magazine_release_standoff)."},"ar15.mag_release_pocket_w":{"label":"AR-15 lower, the magazine release button's pocket, width (fore and aft)","kind":"length","measurements":[{"id":"model","value":0.319,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its planar and cylindrical faces read from the STEP text (.cache/fence/step.py), in the rifle frame set by its two .251 pin holes (6.376 in apart) and its buffer tower (0.88 above them); the pocket's two half-round ends, radius 0.1594, centred on X 3.291","via":"user"},"note":"Its button is .300 BASIC (TDP 8448636): about .01 clear each side."}]},"ar15.mag_release_pocket_h":{"label":"AR-15 lower, the magazine release button's pocket, height","kind":"length","measurements":[{"id":"model","value":0.515,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its planar and cylindrical faces read from the STEP text (.cache/fence/step.py), in the rifle frame set by its two .251 pin holes (6.376 in apart) and its buffer tower (0.88 above them); the ends' centres at Y -0.464 and -0.660, plus their 0.1594 radius each","via":"user"},"note":"Its button is .500 BASIC (TDP 8448636)."}]},"ar15.mag_release_pocket_depth":{"label":"AR-15 lower, the magazine release button's pocket, depth below the fence's face","kind":"length","measurements":[{"id":"model","value":0.617,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its planar and cylindrical faces read from the STEP text (.cache/fence/step.py), in the rifle frame set by its two .251 pin holes (6.376 in apart) and its buffer tower (0.88 above them); the pocket's walls from the fence's face (0.5404) to its floor (-0.0768), where the counterbore begins","via":"user"}}]},"ar15.mag_catch_cbore_d":{"label":"AR-15 lower, the magazine catch hole's counterbore, diameter","kind":"length","measurements":[{"id":"tdp","value":0.312,"unit":"in","pm":0.004,"stated":".312 DIA +.004 CBORE","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P (read by the M5 research agent); user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p63","via":"user"}}]},"ar15.mag_catch_cbore_depth":{"label":"AR-15 lower, the magazine catch hole's counterbore, depth below the pocket's floor","kind":"length","measurements":[{"id":"model","value":0.25,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its planar and cylindrical faces read from the STEP text (.cache/fence/step.py), in the rifle frame set by its two .251 pin holes (6.376 in apart) and its buffer tower (0.88 above them); the counterbore's cylinder (radius 0.1555, the TDP's .312 with clearance) from -0.0768 to -0.3268","via":"user"}}]},"ar15.front_lug_slot_width":{"label":"AR-15 lower, the slot between the pivot lug's ears (where the upper's front lug goes), width","kind":"length","measurements":[{"id":"tdp","value":0.5,"unit":"in","pm":0.005,"stated":".500 REF","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 2 of 2, rev P: Section C-C (read in the 2026-10-03 research pass, .cache/research/aero-lower/REPORT.md); user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p63","via":"user"},"note":"A reference figure: the upper's front lug fits it. Used as the horizontal standard of a photo looking at the lower's front."}]},"ar15.trigger_tail_behind_pivot":{"label":"AR-15 mil-spec trigger, its tail's end behind its pivot hole's centre","kind":"length","measurements":[{"id":"tdp","value":1.2025,"unit":"in","pm":0.0075,"stated":"1.210 -.015","source":{"type":"standard","doc":"US Army TDP drawing 8448592 (Trigger), rev L, scale 2/1: the side elevation; user-supplied scan (Distribution Statement F, Colt proprietary notice), PDF page 43 (references/aero-m4e1-lower 1dabf089edf8)","via":"user"}},{"id":"model","value":1.1986,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Trigger.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of the mil-spec trigger)","method":"its outline's rearmost point from the pivot hole's axis (.cache/research/aero-lower/trigger_step.py)","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's (the middle of 1.195 to 1.210); the model agrees."}},"ar15.trigger_blade_below_pivot":{"label":"AR-15 mil-spec trigger, its blade's lowest point below its pivot hole's centre","kind":"length","measurements":[{"id":"tdp","value":1.45,"unit":"in","pm":0.02,"stated":"1.45 ± .02","source":{"type":"standard","doc":"US Army TDP drawing 8448592 (Trigger), rev L, scale 2/1: the side elevation; user-supplied scan (Distribution Statement F, Colt proprietary notice), PDF page 43 (references/aero-m4e1-lower 1dabf089edf8)","via":"user"}},{"id":"model","value":1.435,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Trigger.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of the mil-spec trigger)","method":"its blade's lowest point from the pivot hole's axis","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's; the model is within its ±."}},"ar15.trigger_body_width":{"label":"AR-15 mil-spec trigger, its body's width (-B-)","kind":"length","measurements":[{"id":"tdp","value":0.29,"unit":"in","pm":0.005,"stated":".290 -B-","source":{"type":"standard","doc":"US Army TDP drawing 8448592 (Trigger), rev L, scale 2/1: the side elevation; user-supplied scan (Distribution Statement F, Colt proprietary notice), PDF page 43 (references/aero-m4e1-lower 1dabf089edf8) (the top view)","via":"user"}},{"id":"model","value":0.29,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Trigger.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of the mil-spec trigger)","method":"its side faces at ±0.145","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's; the model's the same."}},"ar15.trigger_boss_d":{"label":"AR-15 mil-spec trigger, the bosses round its pivot hole, diameter","kind":"length","measurements":[{"id":"tdp","value":0.3145,"unit":"in","pm":0.0075,"stated":".322 DIA -.015","source":{"type":"standard","doc":"US Army TDP drawing 8448592 (Trigger), rev L, scale 2/1: the side elevation; user-supplied scan (Distribution Statement F, Colt proprietary notice), PDF page 43 (references/aero-m4e1-lower 1dabf089edf8) (the front view)","via":"user"}},{"id":"model","value":0.3144,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Trigger.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of the mil-spec trigger)","method":"the bosses' cylinder","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's; the model's the same."}},"ar15.trigger_boss_length":{"label":"AR-15 mil-spec trigger, the bosses round its pivot hole, end to end","kind":"length","measurements":[{"id":"model","value":0.664,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Trigger.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of the mil-spec trigger)","method":"the bosses' cylinder end to end (±0.332)","via":"user"}}],"note":"Not dimensioned on the drawing (it scales about 0.68 to 0.69, inside the pocket's .690)."},"ar15.mag_catch_hole_d":{"label":"AR-15 lower, the magazine catch hole, diameter (through to the slot on the left)","kind":"length","measurements":[{"id":"tdp","value":0.2055,"unit":"in","pm":0.0015,"stated":".204 DIA +.003 THRU / .312 DIA +.004 CBORE TO DEPTH SHOWN","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: side elevation, zone A-3 (-T-); user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"}}]},"ar15.takedown_hole_d":{"label":"AR-15 lower, the takedown pin hole (-V-), diameter","kind":"length","measurements":[{"id":"tdp","value":0.251,"unit":"in","pm":0.001,"stated":".251 DIA ±.001 THRU BOTH SIDES .44 DIA SPOTFACE TO DEPTH SHOWN SECTION E-E .250 DIA GAGE PLUG MUST PASS THRU BOTH SIDES SIMULTANEOUSLY","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: side elevation, zone C-7; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"}}]},"ar15.takedown_spotface_d":{"label":"AR-15 lower, the takedown pin hole's spotface, diameter","kind":"length","measurements":[{"id":"tdp","value":0.44,"unit":"in","pm":0.01,"stated":".44 DIA SPOTFACE TO DEPTH SHOWN SECTION E-E","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: side elevation, zone C-7; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"}}],"note":"The drawing calls for it both sides, to a depth drawn in Section E-E (sheet 2, not read). The reference CAD model has it on the right only, and so do the Workhorse's photos: a ring round the right side's hole, none round the left's (a pin's head covers it there)."},"ar15.takedown_spotface_depth":{"label":"AR-15 lower, the takedown pin hole's spotface, depth","kind":"length","measurements":[{"id":"model","value":0.04,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its cylindrical faces read from the STEP text (.cache/fence/zext.py), in the rifle frame set by its two .251 pin holes: the .4409 spotface's cylinder from the right ear's face (Z 0.4513) to its floor (0.4114), where the .2510 hole begins","via":"user"}}]},"ar15.pivot_hole_d":{"label":"AR-15 lower, the pivot pin hole (-AC-), diameter","kind":"length","measurements":[{"id":"tdp","value":0.251,"unit":"in","pm":0.001,"stated":".251 DIA ±.001 THRU BOTH LUGS 90° CSK TO .27 DIA THIS SIDE ONLY .250 DIA GAGE PLUG MUST PASS THRU BOTH HOLES SIMULTANEOUSLY","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: side elevation, zone B-3; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"},"note":"The .27 countersink (0.01 a side) isn't drawn."}]},"ar15.selector_hole_d":{"label":"AR-15 lower, the safety selector hole (-M-), diameter","kind":"length","measurements":[{"id":"tdp","value":0.376,"unit":"in","pm":0.001,"stated":".376 DIA ±.001 THRU BOTH SIDES .375 DIA GAGE PLUG MUST PASS THRU BOTH SIDES SIMULTANEOUSLY","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: side elevation, zone C-7; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"}}]},"ar15.selector_shaft_d":{"label":"AR-15 safety selector, the diameter of the shaft that turns in the receiver","kind":"length","measurements":[{"id":"tdp","value":0.37225,"unit":"in","pm":0.00075,"stated":".3730 DIA -.0015 -N-","source":{"type":"standard","doc":"US Army TDP drawing 9381367 (Selector, Fire Control), sheet 1 of 2, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp lpk-up-p65: the view along the rifle, zone B-4","via":"user"},"note":"The middle of .3715 to .3730 (ground after heat treat, note 8). In the receiver's .376 hole (std.ar15.selector_hole_d)."},{"id":"model","value":0.3715,"unit":"in","pm":0.0005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Fire_Selector.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle)","method":"its faces read from the STEP text (.cache/batch7/cmmg-safety-selector/step_sel.py): the shaft's cylinders, r 4.718 mm","via":"user"}}],"adopt":{"from":"tdp","reason":"The Army's drawing; the reference model has the low end of its tolerance."},"note":"The standard selector's own half of its seat in the lower's hole (ar15.selector_hole_d, .376): what a selector made to go in that hole is turned to, whoever makes it. Entered 2026-10-12 with the first selectors sold on their own (D86)."},"ar15.fcg_pin_hole_d":{"label":"AR-15 lower, the hammer and trigger pin holes, diameter","kind":"length","measurements":[{"id":"tdp","value":0.15675,"unit":"in","pm":0.00075,"stated":".1560 DIA +.0015 THRU BOTH SIDES .1560 DIA GAGE PLUG MUST PASS THRU BOTH SIDES SIMULTANEOUSLY. 2 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: side elevation, zone A-6; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"},"note":"The small-pin holes (data/interfaces.yaml, ar15.fcg)."}]},"ar15.trigger_guard_rear_hole_d":{"label":"AR-15 lower, the trigger guard's rear (roll pin) hole, diameter","kind":"length","measurements":[{"id":"tdp","value":0.1285,"unit":"in","pm":0.001,"stated":".1275 DIA +.0020 THRU BOTH SIDES","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: side elevation, zone A-6; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"}}]},"ar15.trigger_guard_front_hole_d":{"label":"AR-15 lower, the trigger guard's front hole, diameter (the right ear only)","kind":"length","measurements":[{"id":"tdp","value":0.1265,"unit":"in","pm":0.0015,"stated":".250 DIA SPOTFACE TO DEPTH SHOWN, .125 DIA +.003 THRU THIS SIDE ONLY, 90° CSK TO .150 DIA MAX OPTIONAL","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: side elevation, zone A-4 (view P on sheet 2 not read); user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"}}]},"ar15.trigger_guard_front_spotface_d":{"label":"AR-15 lower, the trigger guard's front hole, its spotface's diameter","kind":"length","measurements":[{"id":"tdp","value":0.25,"unit":"in","pm":0.005,"stated":".250 DIA SPOTFACE TO DEPTH SHOWN","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: side elevation, zone A-4; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"}}]},"ar15.trigger_guard_front_spotface_floor":{"label":"AR-15 lower, the trigger guard's front spotface, its floor from the centre (right side)","kind":"length","measurements":[{"id":"model","value":0.3219,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its cylindrical faces read from the STEP text (.cache/fence/zext.py): the .2500 spotface's cylinder at X 3.343, Y -2.179 from the ear's face (Z 0.5451) in to 0.3219, the .1250 hole from there to the ear's inner face (0.2195)","via":"user"}}]},"ar15.trigger_guard_ear_gap":{"label":"AR-15 lower, the gap between the trigger guard's ears (where the guard's ends go)","kind":"length","measurements":[{"id":"model","value":0.439,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"the ears' inner faces at Z ±0.2195, where both guard holes' cylinders end (.cache/fence/zext.py)","via":"user"},"note":"Section B-B on sheet 1 has a '.438 -.008' (-W-) across the bottom that may be this gap; not read further."},{"id":"tdp","value":0.442,"unit":"in","pm":0.004,"stated":".438 +.008","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 2 of 2, rev P: View R-R (the grip's lug and the trigger guard's rear ears from below); user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p63","via":"user"},"note":"Between the rear ears, seen from below, and symmetrical about their outside faces (-AA-) within .010 total: .438 to .446, the middle here. Read 2026-10-05, when the ears were first drawn apart."}],"adopt":{"from":"tdp","reason":"The drawing dimensions it; the model's 0.439 is inside it."}},"ar15.grip_lug_width":{"label":"AR-15 lower, the grip's lug (the tang a grip's slot goes over), width","kind":"length","measurements":[{"id":"tdp","value":0.375,"unit":"in","pm":0.01,"stated":".375; .1875 ±.005 from the centre plane to a side","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 2 of 2, rev P: View R-R (the grip's lug and the trigger guard's rear ears from below); user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p63","via":"user"},"note":"The lug seen from below, the grip screw's tapped hole in it. ± is the two sides' together. The reference CAD model has its sides at Z ±0.188."}]},"ar15.grip_seat_below_deck":{"label":"AR-15 lower, the underside either side of the grip's lug (where a grip's top bears), below the top deck","kind":"length","measurements":[{"id":"tdp","value":1.318,"unit":"in","pm":0.01,"stated":"1.318 ±.010","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: side elevation, at the grip's lug; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"},"note":"From the receiver's top surface down to the flat the lug hangs from: with the deck .2485 above the pin line (std.ar15.deck_y), 1.0695 below it. The reference CAD model has the flat at Y -1.069. The Workhorse's two side photos read it 1.072 and 1.062 below the pin line through cameras fitted to them (bad-workhorse-lower.grip_mating_y, 2026-10-05), either side of the drawing's. In two-pin frames they had read 1.096 and 1.092, which was the underside's far edge, seen from 0.7 in below and taken for the near face's."}]},"ar15.grip_lug_depth":{"label":"AR-15 lower, the grip's lug, its bottom flat below the underside it hangs from","kind":"length","measurements":[{"id":"tdp","value":0.93,"unit":"in","pm":0.01,"stated":".93","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: side elevation, at the grip's lug; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"},"note":"From the underside down to the short flat the sloped face ends in, just behind the trigger guard's ears (two-place: ± .01). The reference CAD model: Y -1.069 to -1.998."}]},"ar15.grip_lug_face_from_pin":{"label":"AR-15 lower, the grip lug's sloped face (the face the grip screw goes into), from the takedown pin's centre, square to the face","kind":"length","measurements":[{"id":"tdp","value":1.228,"unit":"in","pm":0.01,"stated":"1.228 ±.010","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: side elevation, at the grip's lug; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"},"note":"Dimensioned between the face and a line drawn through the takedown pin's centre parallel to it: the face is the line 1.228 from that centre, descending forward at std.ar15.grip_lug_face_angle. The Workhorse's two side photos have the face 1.225 and 1.217 from the pin at 60.1 and 59.9 degrees (bad-workhorse-lower.grip_lug_face_from_pin, _angle)."}]},"ar15.grip_lug_face_angle":{"label":"AR-15 lower, the grip lug's sloped face, from the vertical","kind":"angle","measurements":[{"id":"tdp","value":60,"unit":"deg","pm":2,"stated":"60° ±2°","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: side elevation, at the grip's lug; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"},"note":"Between the lug's upright rear face and the sloped face: the face descends forward at 30° to the underside, and the grip screw's line stands 30° from the vertical."}]},"ar15.grip_lug_length":{"label":"AR-15 lower, the grip's lug, length (its rear face to the trigger guard's rear ears)","kind":"length","measurements":[{"id":"tdp","value":1.25,"unit":"in","pm":0.01,"stated":"1.25","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: side elevation, at the grip's lug; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"},"note":"Along the underside, from the lug's upright rear face forward to the ears' rear face (two-place: ± .01). The reference CAD model: X -0.079 to 1.171."}]},"ar15.grip_lug_front_from_rear_face":{"label":"AR-15 lower, the trigger guard's rear ears, their rear face (where the grip's lug ends), ahead of the receiver's rear face","kind":"length","measurements":[{"id":"tdp","value":2.3,"unit":"in","pm":0.01,"stated":"2.300","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: side elevation, at the grip's lug; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"},"note":"From the receiver's rear face (std.ar15.receiver_rear_x, -1.125): the ears' rear face at X 1.175 and, std.ar15.grip_lug_length behind it, the lug's rear face at -0.075, under the takedown pin. No tolerance is given at the figure: ± .01 here. The Workhorse's two side photos, through cameras fitted to them (2026-10-05), have its ears' rear face at X 1.169 and 1.162 (bad-workhorse-lower.guard_ears_rear_x: the drawing's, within their ±; a two-pin frame had read them 0.045 behind) and its lug's rear face at X 0.122 and 0.126 (grip_shelf_top_x), 0.20 ahead of the drawing's: that face is the Workhorse's own, and its outline has it there."}]},"ar15.trigger_guard_ears_width":{"label":"AR-15 lower, the trigger guard's rear ears and the wall they hang from, across their outside faces","kind":"length","measurements":[{"id":"model","value":0.659,"unit":"in","pm":0.01,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"the two outside faces of the wall behind the trigger, planes at Z ±0.3297 over X 1.152 to 1.648 and Y -2.299 to -1.222; the ears' inside faces at ±0.2195 over X 1.171 to 1.680, Y -2.360 to -2.014 (.cache/grip-lower/step_lug.py, 2026-10-05)","via":"user"},"note":"The drawing's View R-R (sheet 2) names these faces as a datum (-AA-) and draws them 0.66 apart at the scale its .375 lug gives; the sheets on file don't dimension them. The wall behind the trigger is this wide from the ears up to where it flares to the body (Y -1.22 in the model)."}]},"ar15.rear_underside_arc_r":{"label":"AR-15 lower, the rear underside (from under the buffer tower down to the grip's seat), its arc along the centre plane, radius","kind":"length","measurements":[{"id":"model","value":0.75,"unit":"in","pm":0.01,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"the one toroidal face under the rear, in the frame the model's pin holes set: its axis across the receiver through X -1.0238, Y -1.2618, major radius 1.185 and minor 0.435, so 0.750 on the centre plane; it runs from under the tower to the seat at Y -1.069 (.cache/grip-lower/step_undercut.py, 2026-10-05)","via":"user"},"note":"The forging's shape, which the drawing's side elevation draws and these sheets don't dimension."},{"id":"workhorse","value":0.716,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{bad-workhorse-lower.rear_underside_arc_r}","via":"harvest"},"note":"A second forging: Battle Arms' Workhorse, whose two side photos read through cameras fitted to them (2026-10-05) have its underside 0.716 and 0.723 from the same centre, one distance all along it."}],"adopt":{"from":"model","reason":"Two forgings, two radii, 0.034 apart, and neither is the standard (the forging drawing isn't on file). The reference model's is kept here for a lower drawn from the standard where its own underside isn't read (Bear Creek's); the Workhorse's model follows its own outline, and a grip is cut clear of the fuller of the two (std.ar15.rear_underside_arc_r_fullest)."},"note":"Until 2026-10-05 the reference model's alone: the Workhorse's outline, traced then in a frame set by its two pins, had seemed to follow the model's arc from its own seat, which that frame read 0.027 low."},"ar15.rear_underside_arc_r_fullest":{"label":"AR-15 lower, the rear underside's arc along the centre plane where it is fullest among the forgings on file (what a grip's beavertail has to clear), radius","kind":"length","measurements":[{"id":"workhorse","value":0.716,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{bad-workhorse-lower.rear_underside_arc_r}","via":"harvest"},"note":"Battle Arms' Workhorse, 0.034 fuller than the reference CAD model's 0.750 (2026-10-05). Until then grips were cut to the model's arc, and on the Workhorse, once its seat was read where the Army's drawing has it, their saddles stood 0.008 in into its underside."}],"note":"About the same centre as std.ar15.rear_underside_arc_r (std.ar15.rear_underside_arc_center_x, _below_seat). pipeline/blender/lib.py grip_receiver_cuts cuts the saddle between a grip's horns to this arc, a clearance off: a grip goes on any lower, so it is cut for the one that leaves it least room. A forging read fuller than this one takes its place here."},"ar15.rear_underside_arc_center_x":{"label":"AR-15 lower, the rear underside's arc, its centre, X (from the takedown pin)","kind":"length","measurements":[{"id":"model","value":-1.0238,"unit":"in","pm":0.01,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"the one toroidal face under the rear, in the frame the model's pin holes set: its axis across the receiver through X -1.0238, Y -1.2618, major radius 1.185 and minor 0.435, so 0.750 on the centre plane; it runs from under the tower to the seat at Y -1.069 (.cache/grip-lower/step_undercut.py, 2026-10-05)","via":"user"}}]},"ar15.rear_underside_arc_center_below_seat":{"label":"AR-15 lower, the rear underside's arc, its centre below the grip's seat","kind":"length","measurements":[{"id":"model","value":0.1928,"unit":"in","pm":0.01,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"the one toroidal face under the rear, in the frame the model's pin holes set: its axis across the receiver through X -1.0238, Y -1.2618, major radius 1.185 and minor 0.435, so 0.750 on the centre plane; it runs from under the tower to the seat at Y -1.069 (.cache/grip-lower/step_undercut.py, 2026-10-05)","via":"user"},"note":"The centre at Y -1.2618 in the model, whose seat is at -1.0690. The arc meets the seat 0.725 ahead of its centre on the centre plane, and at the body's sides not until 1.169 ahead: the seat's rear edge is a U, as the top of a grip made for it is."}]},"ar15.rear_underside_round_r":{"label":"AR-15 lower, the rear underside's round across the receiver, radius","kind":"length","measurements":[{"id":"model","value":0.435,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"the one toroidal face under the rear, in the frame the model's pin holes set: its axis across the receiver through X -1.0238, Y -1.2618, major radius 1.185 and minor 0.435, so 0.750 on the centre plane; it runs from under the tower to the seat at Y -1.069 (.cache/grip-lower/step_undercut.py, 2026-10-05)","via":"user"},"note":"Half the model's own body (0.870 wide): the underside behind the grip is a full half-round, which a grip's beavertail wraps."},{"id":"half-body","value":0.44,"unit":"in","pm":0.004,"source":{"type":"derived","expr":"{std.ar15.lower_body_width} / 2"},"note":"The same half-round on the drawing's body."}],"adopt":{"from":"half-body","reason":"The model has a full half-round of its own body, which is 1.1% under the drawing's (std.ar15.mag_catch_fence_out says the same of its walls): on the drawing's 0.880 body a full half-round is 0.440."}},"ar15.hammer_pin_y":{"label":"AR-15 hammer pin hole, Y (below the pin line)","kind":"length","measurements":[{"id":"tdp","value":-0.375,"unit":"in","pm":0.002,"stated":".375 ±.002","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: side elevation, zone C-4: from the line through the takedown and pivot holes down to the hammer pin hole's centre line; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"}},{"id":"model","value":-0.376,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"the .1560 hole's axis in the rifle frame set by its two .251 pin holes (.cache/fence/zholes.py)","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing dimensions it; the model agrees within 0.001, and so does the Workhorse's left photo (-0.376)."}},"ar15.trigger_pin_y":{"label":"AR-15 trigger pin hole, Y (below the pin line)","kind":"length","measurements":[{"id":"tdp","value":-0.689,"unit":"in","pm":0.0035,"stated":".375 ±.002 and .3140 ±.0015","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 1 of 2, rev P: side elevation, zone C-4: .375 down to the hammer pin hole, .3140 from it down to the trigger pin hole; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p64","via":"user"}},{"id":"model","value":-0.691,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"the .1560 hole's axis in the rifle frame set by its two .251 pin holes (.cache/fence/zholes.py)","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing dimensions it; the model agrees within 0.002, and so does the Workhorse's left photo (-0.689)."}},"ar15.mag_catch_slot_rear_x":{"label":"AR-15 lower, the magazine catch's slot (left side), rear end, X","kind":"length","measurements":[{"id":"tdp","value":3.048,"unit":"in","pm":0.012,"stated":".243 ±.008 behind -T-","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 2 of 2, rev P: Section A-A and View H-H; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p63","via":"user"},"note":"The catch hole (std.ar15.mag_catch_x, 3.291) less .243."},{"id":"model","value":3.049,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"the slot's rear half-round end, radius .125 about X 3.174 (.cache/fence/zholes.py)","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's, which the model matches within 0.001."}},"ar15.mag_catch_slot_front_x":{"label":"AR-15 lower, the magazine catch's slot (left side), front end, X","kind":"length","measurements":[{"id":"tdp","value":4.557,"unit":"in","pm":0.02,"stated":"1.509 ±.008","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 2 of 2, rev P: Section A-A; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p63","via":"user"},"note":"The slot's length from its rear end (std.ar15.mag_catch_slot_rear_x)."},{"id":"model","value":4.559,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"the slot's front half-round end, radius .125 about X 4.434 (.cache/fence/zholes.py)","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's, which the model matches within 0.002."}},"ar15.mag_catch_slot_bottom_y":{"label":"AR-15 lower, the magazine catch's slot (left side), its lower edge, Y","kind":"length","measurements":[{"id":"tdp","value":-0.689,"unit":"in","pm":0.005,"stated":".9375 ±.0035 (-AM-)","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 2 of 2, rev P: Section A-A, from the deck; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p63","via":"user"},"note":"The deck (std.ar15.deck_y, 0.2485) less .9375. Taken as the slot's lower face: the model's is there, and the Workhorse's left photo has the slot from Y -0.70 to -0.42."},{"id":"model","value":-0.6875,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"the slot's lower plane (.cache/fence/near.py)","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's; the model's is the same callout from its deck at .250."}},"ar15.mag_catch_slot_h":{"label":"AR-15 lower, the magazine catch's slot (left side), height","kind":"length","measurements":[{"id":"tdp","value":0.252,"unit":"in","pm":0.002,"stated":".250 +.004 -AM-","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 2 of 2, rev P: View H-H; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p63","via":"user"}},{"id":"model","value":0.25,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its planes at Y -0.687 and -0.437 (.cache/fence/near.py)","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's; the model has the nominal."}},"ar15.mag_catch_slot_floor":{"label":"AR-15 lower, the magazine catch's slot, its floor from the centre (left side)","kind":"length","measurements":[{"id":"model","value":0.3799,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"the floor's plane at Z -0.3799, X 3.174 to 3.628 (to the well's rear wall), Y -0.687 to -0.437 (.cache/fence/step.py)","via":"user"}}],"note":"Inside the well's wall (.898 across inside: 0.449 from the centre), so the slot opens into the well wherever the well is and has a floor behind it, where the catch hole comes through."},"ar15.mag_catch_boss_x":{"label":"AR-15 lower, the round boss the magazine catch's slot runs through (left side), its centre, X","kind":"length","measurements":[{"id":"model","value":4.262,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"the axis of its edge's torus (.cache/fence/near.py), on the slot's centre line (Y -0.563)","via":"user"},"note":"The Workhorse's left photo shows it: a circle about 0.52 across centred near X 4.24."}]},"ar15.mag_catch_boss_r":{"label":"AR-15 lower, the magazine catch's round boss, radius at its base","kind":"length","measurements":[{"id":"model","value":0.253,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its edge's torus: 0.194 to the tube's centre plus the tube's 0.0591 (.cache/fence/near.py)","via":"user"}}]},"ar15.mag_catch_boss_proud":{"label":"AR-15 lower, the magazine catch's round boss, how far its face stands out of the band","kind":"length","measurements":[{"id":"model","value":0.0906,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its face's plane at Z -0.6900 against the band's at -0.5994 (.cache/fence/near.py)","via":"user"}}]},"ar15.mag_catch_boss_edge_r":{"label":"AR-15 lower, the magazine catch's round boss, its face's edge radius","kind":"length","measurements":[{"id":"model","value":0.059,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its edge's torus, tube radius 0.0591 (.cache/fence/near.py)","via":"user"}}]},"ar15.magwell_band_rear_x":{"label":"AR-15 lower, the raised band down the magazine well's left wall, its face's rear edge, X","kind":"length","measurements":[{"id":"model","value":3.975,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"the band's face (the plane at Z -0.5994), X 3.975 to 4.549; its sides' cylinders from X 3.891 and to 4.632 (.cache/fence/near.py)","via":"user"},"note":"The Workhorse's left photo has the band's two edges as the shadow lines near X 3.96 and 4.52."}],"note":"A band standing out of the well's left wall from the deck to the lip, the magazine catch's boss on it. Its sides fall to the wall in two radii (0.0295 and 0.0591) over 0.084 behind and ahead of the face, drawn as a slope."},"ar15.magwell_band_front_x":{"label":"AR-15 lower, the raised band down the magazine well's left wall, its face's front edge, X","kind":"length","measurements":[{"id":"model","value":4.549,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"the band's face (the plane at Z -0.5994), X 3.975 to 4.549 (.cache/fence/near.py)","via":"user"}}]},"ar15.magwell_band_side":{"label":"AR-15 lower, the raised band, how far its sides run from the face's edges to the wall","kind":"length","measurements":[{"id":"model","value":0.084,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"the rear side's two cylinders from X 3.891 to 3.975, the front's from 4.549 to 4.632 (0.083) (.cache/fence/near.py)","via":"user"}}]},"ar15.magwell_band_proud":{"label":"AR-15 lower, the raised band, how far it stands out of the well's wall","kind":"length","measurements":[{"id":"model","value":0.059,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its face's plane at Z -0.5994 against the wall's at -0.5404 (.cache/fence/near.py)","via":"user"}}]},"ar15.magwell_band_bottom_y":{"label":"AR-15 lower, the raised band, its lower end, Y","kind":"length","measurements":[{"id":"model","value":-1.959,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"the band's face's lowest vertex (.cache/fence/near.py)","via":"user"}}]},"ar15.bolt_catch_slot_front_x":{"label":"AR-15 lower, the bolt catch's slot (left side, between the bosses and below them), its front face, X","kind":"length","measurements":[{"id":"tdp","value":3.375,"unit":"in","pm":0.005,"stated":"3.000 (from the pivot pin)","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 2 of 2, rev P: Section A-A, zone E-4; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p63","via":"user"},"note":"6.375 less 3.000."},{"id":"model","value":3.382,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"the slot's floor (Z -0.4409) from X 3.215 to 3.382 (.cache/fence/step.py)","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's; the model's is 0.007 ahead of it."}},"ar15.bolt_catch_slot_width":{"label":"AR-15 lower, the bolt catch's slot, its width at the left face","kind":"length","measurements":[{"id":"tdp","value":0.172,"unit":"in","pm":0.005,"stated":".167 +.010","source":{"type":"standard","doc":"US Army TDP drawing 8448608 (Receiver, Lower), sheet 2 of 2, rev P: View H-H; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p63","via":"user"},"note":"Section A-A, through the middle, has it .155 +.005 there."},{"id":"model","value":0.1673,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its round lower end, diameter .1673 about X 3.298 (.cache/fence/zholes.py)","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's (the middle of .167 to .177); the model has its lower limit."}},"ar15.bolt_catch_slot_bottom_y":{"label":"AR-15 lower, the bolt catch's slot, its round lower end, Y","kind":"length","measurements":[{"id":"model","value":-0.38,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its half-round end, radius .0837 about Y -0.296 (.cache/fence/zholes.py)","via":"user"},"note":"The Workhorse's left photo has the slot's end at about Y -0.37."}]},"ar15.bolt_catch_slot_floor":{"label":"AR-15 lower, the bolt catch's slot, its floor from the centre (left side)","kind":"length","measurements":[{"id":"model","value":0.4409,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"the floor's plane at Z -0.4409, X 3.215 to 3.382, Y -0.296 to -0.049 (.cache/fence/step.py)","via":"user"},"note":"About the body's face: the slot is cut through the wall's thickening round the bosses."}]},"ar15.bolt_catch_plunger_hole_d":{"label":"AR-15 lower, the bolt catch plunger's hole (in the slot's floor), diameter","kind":"length","measurements":[{"id":"model","value":0.156,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its cylinder at X 3.297, Y -0.195, from the slot's floor (Z -0.4409) to +0.0294, a drill point beyond (.cache/fence/zext.py)","via":"user"}}]},"ar15.bolt_catch_plunger_hole_y":{"label":"AR-15 lower, the bolt catch plunger's hole, Y","kind":"length","measurements":[{"id":"model","value":-0.195,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its cylinder's axis (.cache/fence/zext.py)","via":"user"},"note":"The Workhorse's left photo has the hole at about Y -0.23, in the slot's middle."}]},"ar15.bolt_catch_plunger_hole_depth":{"label":"AR-15 lower, the bolt catch plunger's hole, depth from the slot's floor","kind":"length","measurements":[{"id":"model","value":0.4703,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Lower_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its cylinder from Z -0.4409 to +0.0294 (.cache/fence/zext.py)","via":"user"}}]},"receiver_extension.front_face_x":{"label":"Receiver extension, front face when screwed home, X (from the takedown pin)","kind":"length","measurements":[{"id":"tdp","value":-0.669,"unit":"in","pm":0.02,"stated":"retainer: .250 DIA -.003 body, .093 DIA tip, .046 R between them","source":{"type":"standard","doc":"US Army TDP drawings 8448582 (Retainer, Buffer), rev F; 8448579 (Lower Receiver and Receiver Extension Assembly), rev C; 8448608 (Receiver, Lower), sheet 2 of 2, Section A-A; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p8, p77, p63","via":"user"},"note":"Behind the retainer's axis (std.ar15.buffer_retainer_x) by more than its tip and fillet (.0465 + .046) and less than its body's radius (.125): 0.109 ± 0.016. That is 0.04 behind the ring's front face (std.ar15.buffer_tower_front_x)."}],"note":"No drawing here dimensions how far the extension screws in: it goes in until its lower edge stands over the buffer retainer's shoulder, short of its tip, which is what holds the retainer down (the assembly drawing shows it so). M5 drew the tube from the takedown pin's X, an assumption; this puts it 0.67 further back. Checked on Magpul's photo of an M4 through the stock's lock pin (bcm-receiver-extension.tube_front_behind_pin)."},"picatinny.slot_pitch":{"label":"Picatinny slot pitch (center to center)","kind":"length","measurements":[{"id":"std","value":0.394,"unit":"in","stated":"0.394 in (10 mm)","source":{"type":"standard","doc":"MIL-STD-1913","via":"brief"}}]},"picatinny.top_width":{"label":"Picatinny rail top width","kind":"length","measurements":[{"id":"std","value":0.835,"unit":"in","pm":0.005,"stated":".835 -.005 (Figure 1, accessory mounting rail profile)","source":{"type":"standard","doc":"MIL-STD-1913, Figure 1","url":"https://www.biggerhammer.net/picatinny/1913_specs.pdf","via":"harvest"},"note":"Tolerance is one-sided (−.005); ± here is its magnitude."}]},"picatinny.bevel_width":{"label":"Picatinny rail, its width across the 45 degree faces at the two gauge lines","kind":"length","measurements":[{"id":"std","value":0.748,"unit":"in","pm":0.002,"stated":".748 +/-.002 (datum -C-), 2X 45 degrees (basic)","source":{"type":"standard","doc":"MIL-STD-1913 (AR), 3 February 1995, Figure 1 (Accessory mounting rail profile), p. 4","url":"https://www.biggerhammer.net/picatinny/1913_specs.pdf","via":"harvest"}}]},"picatinny.bevel_gauge_apart":{"label":"Picatinny rail, the two gauge lines apart (one on the upper 45 degree faces, one on the lower)","kind":"length","measurements":[{"id":"std","value":0.108,"unit":"in","pm":0.001,"stated":".108 (basic)","source":{"type":"standard","doc":"MIL-STD-1913 (AR), 3 February 1995, Figure 1 (Accessory mounting rail profile), p. 4","url":"https://www.biggerhammer.net/picatinny/1913_specs.pdf","via":"harvest"},"note":"A basic dimension: no tolerance of its own. The 45 degree faces meet, sharp, .748 + .108 = .856 apart, and are cut off at .835."}]},"picatinny.lower_gauge_below_top":{"label":"Picatinny rail, the lower gauge line below the rail's top","kind":"length","measurements":[{"id":"std","value":0.154,"unit":"in","pm":0.01,"stated":".164 -.020","source":{"type":"standard","doc":"MIL-STD-1913 (AR), 3 February 1995, Figure 1 (Accessory mounting rail profile), p. 4","url":"https://www.biggerhammer.net/picatinny/1913_specs.pdf","via":"harvest"},"note":"One-sided (.144 to .164): the middle here. The upper line is .108 above it, .046 below the top; the head is widest midway, .100 down, and its top flat is .748 - 2 x .046 = .656 across."}]},"picatinny.slot_width":{"label":"Picatinny recoil-groove (slot) width","kind":"length","measurements":[{"id":"std","value":0.206,"unit":"in","pm":0.008,"stated":".206 +.008 (Figure 2, recoil groove)","source":{"type":"standard","doc":"MIL-STD-1913, Figure 2","url":"https://www.biggerhammer.net/picatinny/1913_specs.pdf","via":"harvest"},"note":"One-sided tolerance (+.008)."},{"id":"wiki","value":0.206,"unit":"in","stated":"The MIL-STD-1913 locking slot width is 0.206 in (5.23 mm).","source":{"type":"spec","publisher":"review","name":"Wikipedia, Picatinny rail","url":"https://en.wikipedia.org/wiki/Picatinny_rail","retrieved":"2026-09-30","via":"harvest"}}],"adopt":{"from":"std","reason":"The standard."}},"picatinny.slot_depth":{"label":"Picatinny recoil-groove (slot) depth","kind":"length","measurements":[{"id":"std","value":0.118,"unit":"in","pm":0.008,"stated":".118 +.008 (Figure 2, recoil groove)","source":{"type":"standard","doc":"MIL-STD-1913, Figure 2","url":"https://www.biggerhammer.net/picatinny/1913_specs.pdf","via":"harvest"},"note":"One-sided tolerance (+.008). A retailer blog's 0.180 in contradicts its own 3.00 mm and is treated as a typo."}]},"mlok.slot_pitch":{"label":"M-LOK slot pitch (center to center)","kind":"length","measurements":[{"id":"std","value":40,"unit":"mm","source":{"type":"standard","doc":"Magpul M-LOK specification","via":"brief"}}]},"mlok.slot_length":{"label":"M-LOK slot length","kind":"length","measurements":[{"id":"faq","value":32,"unit":"mm","pm":1,"stated":"32mm (*Dimensions are approximate. Full technical data package available for manufacturers on request.)","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, The M-LOK System (M-LOK_2015_FAQs.pdf, Revision 1.2), p. 9, the slot drawing; read on the Internet Archive's copy (magpul.com no longer serves it)","url":"https://web.archive.org/web/20190407022314/https://www.magpul.com/Files/Images/PDF/M-LOK/M-LOK_2015_FAQs.pdf","retrieved":"2026-10-02","via":"harvest"}},{"id":"wiki","value":32,"unit":"mm","stated":"The slots on an M-Lok handguard are approximately 32 mm (1.260 in) long and 7 mm (0.276 in) wide and space 8 mm (0.315 in) from each other.","source":{"type":"spec","publisher":"review","name":"Wikipedia, M-LOK (citing Magpul's M-LOK 2015 FAQs)","url":"https://en.wikipedia.org/wiki/M-LOK","retrieved":"2026-10-01","via":"harvest"}}],"adopt":{"from":"faq","reason":"Magpul's own document, which the encyclopedia cites; Magpul marks the figure approximate, hence the ± 1 mm."},"note":"32 + 8 = 40 mm, the slot pitch (mlok.slot_pitch). The 22RB's slots sit at that pitch in its calibrated photo."},"mlok.slot_width":{"label":"M-LOK slot width","kind":"length","measurements":[{"id":"faq","value":7,"unit":"mm","pm":0.5,"stated":"7mm (*Dimensions are approximate.)","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, The M-LOK System (M-LOK_2015_FAQs.pdf, Revision 1.2), p. 9, the slot drawing; read on the Internet Archive's copy (magpul.com no longer serves it)","url":"https://web.archive.org/web/20190407022314/https://www.magpul.com/Files/Images/PDF/M-LOK/M-LOK_2015_FAQs.pdf","retrieved":"2026-10-02","via":"harvest"}},{"id":"wiki","value":7,"unit":"mm","stated":"approximately 32 mm (1.260 in) long and 7 mm (0.276 in) wide","source":{"type":"spec","publisher":"review","name":"Wikipedia, M-LOK (citing Magpul's M-LOK 2015 FAQs)","url":"https://en.wikipedia.org/wiki/M-LOK","retrieved":"2026-10-01","via":"harvest"}}],"adopt":{"from":"faq","reason":"Magpul's own document, which the encyclopedia cites."}},"mlok.interval":{"label":"M-LOK mounting interval (half a slot pitch)","kind":"length","measurements":[{"id":"faq","value":20,"unit":"mm","stated":"M-LOK accessories can be direct mounted entirely within a slot or bridging between/across slots, making the adjustment interval smaller than the size of a single slot. (Intervals equal two Picatinny rail slots (20mm) of adjustment).","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, The M-LOK System (M-LOK_2015_FAQs.pdf, Revision 1.2), p. 5, Intermediate spacing option; read on the Internet Archive's copy","url":"https://web.archive.org/web/20190407022314/https://www.magpul.com/Files/Images/PDF/M-LOK/M-LOK_2015_FAQs.pdf","retrieved":"2026-10-02","via":"harvest"}},{"id":"page","value":20,"unit":"mm","stated":"Your M-LOK accessory can be adjusted in 20mm increments (1/2 slot length).","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, M-LOK (How to install M-LOK accessories, Step 3)","url":"https://magpul.com/m-lok","retrieved":"2026-10-02","via":"harvest"}}],"adopt":{"from":"faq","reason":"Two Magpul statements of the same figure; the FAQ says what the interval is."},"note":"An accessory's T-nuts sit this far apart, and an accessory can be placed at this interval, within a slot or bridging two. The app's index is the slot (40 mm): the positions between are a known gap (M10)."},"mlok.slot_corner_r":{"label":"M-LOK slot corner radius","kind":"length","measurements":[{"id":"wiki","value":2.38,"unit":"mm","stated":"The radius of the corners is approximately 2.38 mm (0.094 in).","source":{"type":"spec","publisher":"review","name":"Wikipedia, M-LOK (citing Magpul's M-LOK 2015 FAQs)","url":"https://en.wikipedia.org/wiki/M-LOK","retrieved":"2026-10-01","via":"harvest"}}]},"receiver_extension.milspec_od":{"label":"Mil-spec carbine receiver extension OD","kind":"length","measurements":[{"id":"std","value":1.148,"unit":"in","source":{"type":"standard","doc":"Mil-spec carbine receiver extension","via":"brief"}},{"id":"3cr","value":1.148,"unit":"in","stated":"A mil-spec buffer tube has an outer diameter of 1.148 inches.","source":{"type":"spec","publisher":"review","name":"3CR Tactical","url":"https://3crtactical.com/blog/ar-15-buffer-tube-sizes-mil-spec-vs-commercial/","retrieved":"2026-09-30","via":"harvest"}}],"adopt":{"from":"std","reason":"Standard; corroborated."}},"receiver_extension.thread_major_d":{"label":"Receiver extension thread (1 3/16-16 UN-2A), major diameter","kind":"length","measurements":[{"id":"tdp","value":1.1813,"unit":"in","pm":0.0047,"stated":"1 3/16 - 16 UN-2A AFTER FINISH / MAJOR DIA 1.1860 / 1.1766","source":{"type":"standard","doc":"US Army TDP drawing 8448581 (Extension, Receiver: the RIFLE's), rev L, Section F-F, PDF page 12; user-supplied scan (references/…/Spec_Sheets/M16_Technical_Data_Package.pdf), crops in .cache/buffer/std","via":"user"},"note":"The rifle's extension, the only one the Army's package draws: its thread is taken to be a carbine's too, since both screw into the one tapped ring of a lower (the buffer retainer's drawing, 8448582, lists the M4's lower 9390011 beside the M16's). The middle of the two limits; the ± is half their span."},{"id":"model","value":1.1828,"unit":"in","pm":0.0005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Body.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the thread's crest faces, r 0.5914 (.cache/buffer/std/faces.Buffer_Tube_Body_threaded.txt)","via":"user"}},{"id":"seller","value":1.1875,"unit":"in","pm":0.005,"stated":"Standard 1-3/16\"-16 UN Thread","source":{"type":"spec","publisher":"retailer","name":"Dirty Bird Industries, One Horse mil-spec 6-position receiver extension","url":"https://dirtybirdusa.com/products/one-horse-mil-spec-6-position-receiver-extension-buffer-tube/","retrieved":"2026-09-30","via":"harvest"},"note":"The thread's nominal size."}],"adopt":{"from":"tdp","reason":"The Army's drawing of the thread. The reference model's crests are inside its limits, and the seller's 1 3/16 is its nominal size, which an external thread is cut a few thousandths under."}},"receiver_extension.thread_minor_d":{"label":"Receiver extension thread (1 3/16-16 UN-2A), minor diameter","kind":"length","measurements":[{"id":"tdp","value":1.1093,"unit":"in","pm":0.004,"stated":"MINOR DIA 1.1093 MAX","source":{"type":"standard","doc":"US Army TDP drawing 8448581 (Extension, Receiver: the RIFLE's), rev L, Section F-F, PDF page 12; user-supplied scan (references/…/Spec_Sheets/M16_Technical_Data_Package.pdf), crops in .cache/buffer/std","via":"user"},"note":"A maximum: the roots are cut to this or under. The rifle's extension, the only one the Army's package draws: its thread is taken to be a carbine's too, since both screw into the one tapped ring of a lower (the buffer retainer's drawing, 8448582, lists the M4's lower 9390011 beside the M16's)."},{"id":"model","value":1.113,"unit":"in","pm":0.0005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Body.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the thread's root faces, r 0.5565","via":"user"}}],"adopt":{"from":"tdp","reason":"The Army's drawing; the reference model's roots are 0.004 over its maximum."}},"receiver_extension.thread_pitch":{"label":"Receiver extension thread (1 3/16-16 UN-2A), pitch","kind":"length","measurements":[{"id":"tdp","value":0.0625,"unit":"in","pm":0.0001,"stated":"1 3/16 - 16 UN-2A AFTER FINISH","source":{"type":"standard","doc":"US Army TDP drawing 8448581 (Extension, Receiver: the RIFLE's), rev L, Section F-F, PDF page 12; user-supplied scan (references/…/Spec_Sheets/M16_Technical_Data_Package.pdf), crops in .cache/buffer/std","via":"user"},"note":"16 threads to the inch."},{"id":"seller","value":0.0625,"unit":"in","pm":0.0001,"stated":"Standard 1-3/16\"-16 UN Thread","source":{"type":"spec","publisher":"retailer","name":"Dirty Bird Industries, One Horse mil-spec 6-position receiver extension","url":"https://dirtybirdusa.com/products/one-horse-mil-spec-6-position-receiver-extension-buffer-tube/","retrieved":"2026-09-30","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The Army's drawing; the seller's is the same."}},"receiver_extension.thread_length":{"label":"Carbine receiver extension, its threaded length from its front face","kind":"length","measurements":[{"id":"model","value":1.181,"unit":"in","pm":0.01,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Body.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the front face to the thread's square rear end, planes #8958/#9047 (.cache/buffer/std/faces.Buffer_Tube_Body_threaded.txt)","via":"user"},"note":"No drawing on file dimensions a carbine extension. In the model's assembly 0.195 in of thread shows behind the castle nut."}]},"receiver_extension.bore_d":{"label":"Receiver extension, its bore (what a buffer runs in)","kind":"length","measurements":[{"id":"tdp","value":1,"unit":"in","pm":0.003,"stated":"1.000 DIA±.003","source":{"type":"standard","doc":"US Army TDP drawing 8448581 (Extension, Receiver: the RIFLE's), rev L, Section F-F, PDF page 12; user-supplied scan (references/…/Spec_Sheets/M16_Technical_Data_Package.pdf), crops in .cache/buffer/std","via":"user"},"note":"The rifle's extension. Taken to be a carbine's too: the M4's buffer shares the rifle buffer's bumper, weights and discs (8448619, 8448617 and 8448618 list next assembly 9390023 M4), and the reference model's carbine tube is bored 1.000."},{"id":"model","value":1,"unit":"in","pm":0.0005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Buffer_Tube_Body.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"one cylinder, r 0.5000, from the front face to the bore's bottom","via":"user"}}],"adopt":{"from":"tdp","reason":"The Army's drawing; the reference model's carbine tube has the same bore."}},"receiver_extension.carbine_rear_wall":{"label":"Carbine receiver extension, its rear wall behind the bore","kind":"length","measurements":[{"id":"model","value":0.072,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Buffer_Tube_Body.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the bore's flat bottom (plane #1746) to the rear end face (#1241)","via":"user"},"note":"The rifle's extension ends in a thick wall, a boss and a tapped hole (8448581); a carbine's is a thin wall with a small hole. No drawing on file has it."}]},"receiver_extension.carbine_vent_d":{"label":"Carbine receiver extension, the hole through its rear wall, diameter","kind":"length","measurements":[{"id":"model","value":0.094,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Buffer_Tube_Body.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"one cylinder on the axis through the rear wall, r 0.0470 (#1012)","via":"user"}}]},"receiver_extension.key_slot_width":{"label":"Carbine receiver extension, the slot under its thread that an end plate's key rides in, width","kind":"length","measurements":[{"id":"model","value":0.125,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Body.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the slot's two side planes (#138, #5901); the unthreaded copy has 0.126","via":"user"}}]},"receiver_extension.key_slot_floor":{"label":"Carbine receiver extension, the key slot's floor from the tube's axis","kind":"length","measurements":[{"id":"model","value":0.55,"unit":"in","pm":0.01,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Body.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the slot's floor plane (#8931); the unthreaded copy has 0.5326, and the model's end plate's key reaches 0.5619 from the axis","via":"user"}}]},"receiver_extension.key_slot_length":{"label":"Carbine receiver extension, the key slot's length from the tube's front face","kind":"length","measurements":[{"id":"model","value":1.24,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Body.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the slot's rear end plane (#17), 1.2397 from the front face; the unthreaded copy has 1.2402","via":"user"}}]},"receiver_extension.end_plate_hole_d":{"label":"Receiver end plate, the hole the extension's thread passes through, diameter","kind":"length","measurements":[{"id":"model","value":1.1902,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the ring's inner cylinder, r 0.5951 (.cache/buffer/std/faces.Buffer_Tube_Rotation_Lock.txt)","via":"user"},"note":"Nine thousandths over the thread's major diameter as the Army's drawing has it (1.1813). A mil-spec plate as the reference model has it: no drawing of the plate is on file."}]},"receiver_extension.rail_width":{"label":"Mil-spec carbine receiver extension, indexing rail width","kind":"length","measurements":[{"id":"magpul","value":0.49,"unit":"in","pm":0.005,"stated":"SECTION B-B: .495 / .485","source":{"type":"spec","publisher":"manufacturer","name":"Magpul, \"M4 Receiver Extension, Carbine, Military\" partial drawing (rev A, 2008-03-24, scale 1:1.25), via ar15tactical.com","url":"https://ar15tactical.com/wp-content/uploads/2016/09/ar-15-milspec-buffer-tube.pdf","retrieved":"2026-10-01","via":"harvest"}}]},"receiver_extension.rail_bottom_below_axis":{"label":"Mil-spec carbine receiver extension, indexing rail bottom below the tube axis","kind":"length","measurements":[{"id":"magpul-drawing","value":0.874,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"Magpul, \"M4 Receiver Extension, Carbine, Military\" partial drawing (rev A, 2008-03-24, scale 1:1.25), via ar15tactical.com (PDF rendered at 600 dpi)","scaleRef":"its own 7.25 overall length = 3494 px at 600 dpi (481.9 px/in; 1:1.25 would be 480)","method":"the side view's top edge (row 1005) to the rail's bottom edge (row 1703) is 1.448 in; less half the 1.1475 in OD (Ø1.150/1.145 stated)","via":"harvest"}},{"id":"forum","value":0.876,"unit":"in","stated":"Buffer Tube Height 1.45 (approximate and to the nearest hundredth)","source":{"type":"spec","publisher":"forum","name":"M4Carbine.net, CHoffman (Stag mil-spec tube, micrometer)","url":"https://m4carbine.net/t/castle-nut-and-receiver-extension-tube-dimensions/124766","retrieved":"2026-10-01","via":"harvest"},"note":"1.45 less half the 1.148 OD."}],"adopt":{"from":"magpul-drawing","reason":"Magpul's drawing, to scale; the forum's micrometer reading agrees within its hundredth."}},"receiver_extension.rail_ramp_start":{"label":"Mil-spec carbine receiver extension, indexing rail's front ramp, start (from the tube's front face)","kind":"length","measurements":[{"id":"magpul-drawing","value":2.326,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"Magpul, \"M4 Receiver Extension, Carbine, Military\" partial drawing (rev A, 2008-03-24, scale 1:1.25), via ar15tactical.com (PDF rendered at 600 dpi)","scaleRef":"its own 7.25 overall length = 3494 px at 600 dpi (481.9 px/in; 1:1.25 would be 480)","method":"the ramp's first ink, 1.185 in below the top (the rail starts just under the tube's bottom with a 0.03 lip from 1.91, not drawn)","via":"harvest"}}]},"receiver_extension.rail_ramp_end":{"label":"Mil-spec carbine receiver extension, indexing rail's front ramp, end at full depth (from the tube's front face)","kind":"length","measurements":[{"id":"magpul-drawing","value":2.592,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"Magpul, \"M4 Receiver Extension, Carbine, Military\" partial drawing (rev A, 2008-03-24, scale 1:1.25), via ar15tactical.com (PDF rendered at 600 dpi)","scaleRef":"its own 7.25 overall length = 3494 px at 600 dpi (481.9 px/in; 1:1.25 would be 480)","method":"the ramp's last ink at the rail's bottom, 1.451 in below the top; the ramp is 45° (0.266 in either way)","via":"harvest"}}]},"receiver_extension.commercial_od":{"label":"Commercial receiver extension OD","kind":"length","measurements":[{"id":"3cr","value":1.168,"unit":"in","stated":"A commercial tube measures 1.168 inches","source":{"type":"spec","publisher":"review","name":"3CR Tactical","url":"https://3crtactical.com/blog/ar-15-buffer-tube-sizes-mil-spec-vs-commercial/","retrieved":"2026-09-30","via":"harvest"}},{"id":"mountsplus","value":1.169,"unit":"in","pm":0.001,"stated":"Approx. 1.168-1.170 in.","source":{"type":"spec","publisher":"review","name":"Mounts Plus","url":"https://mountsplus.com/milspec-buffer-tube.html","retrieved":"2026-09-30","via":"harvest"}}],"adopt":{"from":"3cr","reason":"Both industry sources agree."},"note":"For the M6 compatibility check (mil-spec vs commercial stocks). No standards document found; industry figures only."},"cartridge_22lr.weight":{"label":".22 Long Rifle cartridge, weight of one loaded round","kind":"mass","measurements":[{"id":"army-ball","value":52,"unit":"gr","stated":"Weight .....................................52 gr","source":{"type":"standard","doc":"TM 43-0001-27, Army Ammunition Data Sheets for Small Caliber Ammunition (Department of the Army, 29 April 1994), p. 3-3: CARTRIDGE, CALIBER .22, BALL, LONG RIFLE (drawing 7553931)","url":"https://www.bulletpicker.com/pdf/TM-43-0001-27.pdf","via":"harvest"},"note":"The match-grade ball cartridge's data sheet: the whole round."},{"id":"army-m24","value":53,"unit":"gr","stated":"Weight ......................................53 gr","source":{"type":"standard","doc":"TM 43-0001-27, Army Ammunition Data Sheets for Small Caliber Ammunition (Department of the Army, 29 April 1994), p. 3-5: CARTRIDGE, CALIBER .22, BALL, LONG RIFLE, M24 (drawing 7640995)","url":"https://www.bulletpicker.com/pdf/TM-43-0001-27.pdf","via":"harvest"},"note":"The M24: a 40.5 gr projectile and 2.5 gr of propellant, on the same sheet."},{"id":"federal-weighed","value":50.85,"unit":"gr","pm":1.05,"stated":"I sorted the measured cartridges into groups: 49.8gr-51.2gr and under, 51.3-51.5gr, and 51.6gr-5.19gr.","source":{"type":"spec","publisher":"review","name":"Moondog Industries, Weight Sorting 22LR","url":"https://moondogindustries.com/weight-sorting-22lr/","retrieved":"2026-10-01","via":"harvest"},"note":"A loose box of Federal Champion (40 gr) weighed round by round on a digital scale: 49.8 to 51.9 gr (the page's \"5.19gr\" is 51.9), about 1 in 30 outside that. The middle of the range, ± half of it."}],"adopt":{"from":"army-ball","reason":"An official data sheet for the standard ball cartridge. The commercial box weighed round by round sits just under it (its range reaches 51.9); the M24 is a grain heavier, and stays as the visible upper end."},"note":"For a build's loaded weight (M7). The Army's two ball cartridges are 52 and 53 gr and a box of commercial 40-grain rounds weighed one by one ran from 49.8 to 51.9: between the lightest and the heaviest of those a full 25-round magazine differs by a fifth of an ounce. Lighter and heavier loads exist (bullets from about 30 to 60 gr); none is on file."},"carbine_buffer.length":{"label":"Carbine buffer, overall length (the head's front face to the bumper's end)","kind":"length","measurements":[{"id":"model","value":3.251,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Weight_Body.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the body's head face to the bumper's end as the two are placed in the model's assembly (.cache/buffer/std/positions.out.txt): the body 2.854, the bumper standing 0.397 out of it","via":"user"},"note":"The rifle's is 5.910 REF (8448615)."}]},"carbine_buffer.body_length":{"label":"Carbine buffer, its body (the head's front face to its open end, where the bumper's shoulder sits)","kind":"length","measurements":[{"id":"model","value":2.854,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Weight_Body.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"planes #246 and #2242","via":"user"}}]},"carbine_buffer.head_d":{"label":"Buffer, its head's diameter (what runs in the extension's bore)","kind":"length","measurements":[{"id":"tdp","value":0.98,"unit":"in","pm":0.005,"stated":".985 DIA -.010","source":{"type":"standard","doc":"US Army TDP drawing 8448616 (Body, Buffer: the RIFLE buffer's), rev F, Section A-A, PDF page 28, end view; user-supplied scan (references/…/Spec_Sheets/M16_Technical_Data_Package.pdf), crops in .cache/buffer/std","via":"user"},"note":"The rifle buffer's body: the Army's package has no drawing of a carbine buffer (9390023 is named on its bumper's, weight's and disc's drawings and not included). One-sided (.975 to .985): the middle here."},{"id":"model","value":0.98,"unit":"in","pm":0.0005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Weight_Body.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the head's cylinder, r 0.4900","via":"user"}}],"adopt":{"from":"tdp","reason":"The Army's drawing of the rifle buffer's head, which runs in the same bore; the reference model's carbine buffer has the same."}},"carbine_buffer.head_flat_across":{"label":"Buffer, its head from one of its three flats to the round opposite","kind":"length","measurements":[{"id":"tdp","value":0.952,"unit":"in","pm":0.005,"stated":".952 (3 FLATS EQUALLY SPACED WITHIN ±10°)","source":{"type":"standard","doc":"US Army TDP drawing 8448616 (Body, Buffer: the RIFLE buffer's), rev F, Section A-A, PDF page 28, end view; user-supplied scan (references/…/Spec_Sheets/M16_Technical_Data_Package.pdf), crops in .cache/buffer/std","via":"user"},"note":"The rifle buffer's body: the Army's package has no drawing of a carbine buffer (9390023 is named on its bumper's, weight's and disc's drawings and not included)."},{"id":"model","value":0.951,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Weight_Body.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"three flats at 120 degrees, 0.458, 0.464 and 0.464 from the axis: 0.948 and 0.954 to the round opposite","via":"user"}}],"adopt":{"from":"tdp","reason":"The Army's drawing; the reference model's three flats straddle it."}},"carbine_buffer.head_rim":{"label":"Carbine buffer, its head's rim (the length of its full diameter)","kind":"length","measurements":[{"id":"model","value":0.214,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Weight_Body.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the head's cylinder from its front face to where its 45 degree back chamfer begins","via":"user"},"note":"The rifle's head is a rim .095 long with a 45 degree taper down to a neck, and a separate collar for the spring (8448616); the carbine's is one thick head."}]},"carbine_buffer.head_thickness":{"label":"Carbine buffer, its head (front face to the rear face the spring bears on)","kind":"length","measurements":[{"id":"model","value":0.254,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Weight_Body.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the seat's plane (#417): the rim's 0.214 and a 45 degree chamfer 0.040 long","via":"user"}}]},"carbine_buffer.pilot_d":{"label":"Buffer, the step behind its head that the spring's end coils sit over, diameter","kind":"length","measurements":[{"id":"model","value":0.781,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Weight_Body.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"cylinder r 0.3905 (#484)","via":"user"}},{"id":"tdp","value":0.781,"unit":"in","pm":0.005,"stated":".786 DIA-.010","source":{"type":"standard","doc":"US Army TDP drawing 8448616 (Body, Buffer: the RIFLE buffer's), rev F, Section A-A, PDF page 28; user-supplied scan (references/…/Spec_Sheets/M16_Technical_Data_Package.pdf), crops in .cache/buffer/std","via":"user"},"note":"The rifle buffer's body: the Army's package has no drawing of a carbine buffer (9390023 is named on its bumper's, weight's and disc's drawings and not included). One-sided (.776 to .786): the middle here."}],"adopt":{"from":"model","reason":"The carbine body as the reference model has it; the rifle drawing's pilot is the same diameter."}},"carbine_buffer.pilot_end":{"label":"Carbine buffer, where its pilot ends behind the head's front face","kind":"length","measurements":[{"id":"model","value":0.468,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Weight_Body.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the pilot's cylinder ends at y 0.468, a cone (#538) down to the body by y 0.5145","via":"user"}}]},"carbine_buffer.body_start":{"label":"Carbine buffer, where its body's diameter begins behind the head's front face","kind":"length","measurements":[{"id":"model","value":0.5145,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Weight_Body.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the body's cylinder (#592) runs from y 0.5145 to the open end","via":"user"}}]},"carbine_buffer.body_d":{"label":"Buffer, its body's diameter","kind":"length","measurements":[{"id":"tdp","value":0.687,"unit":"in","pm":0.005,"stated":".692 DIA-.010","source":{"type":"standard","doc":"US Army TDP drawing 8448616 (Body, Buffer: the RIFLE buffer's), rev F, Section A-A, PDF page 28; user-supplied scan (references/…/Spec_Sheets/M16_Technical_Data_Package.pdf), crops in .cache/buffer/std","via":"user"},"note":"The rifle buffer's body: the Army's package has no drawing of a carbine buffer (9390023 is named on its bumper's, weight's and disc's drawings and not included). One-sided (.682 to .692): the middle here."},{"id":"model","value":0.688,"unit":"in","pm":0.0005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Weight_Body.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"cylinder r 0.3440","via":"user"}}],"adopt":{"from":"tdp","reason":"The Army's drawing of the rifle buffer's body, whose bumper (the M4's too) is turned to the same diameter; the reference model's carbine body agrees."}},"carbine_buffer.bumper_d":{"label":"Buffer, its bumper's head, diameter","kind":"length","measurements":[{"id":"tdp","value":0.687,"unit":"in","pm":0.005,"stated":".692 DIA-.010","source":{"type":"standard","doc":"US Army TDP drawing 8448619 (Bumper, Buffer), rev G, PDF page 25; its application block lists 9390023 M4 beside the M16 and M16A1; user-supplied scan (references/…/Spec_Sheets/M16_Technical_Data_Package.pdf), crops in .cache/buffer/std","via":"user"},"note":"One-sided (.682 to .692): the middle here."},{"id":"model","value":0.69,"unit":"in","pm":0.0005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Weight_Bumper.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"cylinder r 0.3450","via":"user"}}],"adopt":{"from":"tdp","reason":"The Army's drawing of the bumper the M4's buffer shares."}},"carbine_buffer.bumper_band":{"label":"Buffer, its bumper's head: the length of its full diameter before its taper","kind":"length","measurements":[{"id":"tdp","value":0.06,"unit":"in","pm":0.005,"stated":".06","source":{"type":"standard","doc":"US Army TDP drawing 8448619 (Bumper, Buffer), rev G, PDF page 25; its application block lists 9390023 M4 beside the M16 and M16A1; user-supplied scan (references/…/Spec_Sheets/M16_Technical_Data_Package.pdf), crops in .cache/buffer/std","via":"user"}},{"id":"model","value":0.073,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Weight_Bumper.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the cylinder's length","via":"user"}}],"adopt":{"from":"tdp","reason":"The Army's drawing; the reference model draws the band a hundredth longer."}},"carbine_buffer.bumper_exposed":{"label":"Buffer, how far its bumper stands out of the body","kind":"length","measurements":[{"id":"tdp","value":0.4,"unit":"in","pm":0.01,"stated":".873±.010 overall, .473 in the body","source":{"type":"standard","doc":"US Army TDP drawing 8448619 (Bumper, Buffer), rev G, PDF page 25; its application block lists 9390023 M4 beside the M16 and M16A1; user-supplied scan (references/…/Spec_Sheets/M16_Technical_Data_Package.pdf), crops in .cache/buffer/std","via":"user"},"note":"Derived on the drawing: .873 less the shank's .473."},{"id":"model","value":0.397,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Weight_Bumper.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the bumper's shoulder to its end","via":"user"}}],"adopt":{"from":"tdp","reason":"The Army's drawing; the reference model agrees."}},"carbine_buffer.bumper_taper":{"label":"Buffer, its bumper's taper to its end (each side, from the axis)","kind":"angle","measurements":[{"id":"tdp","value":13.5,"unit":"deg","pm":0.5,"stated":"13°30'±0°30'","source":{"type":"standard","doc":"US Army TDP drawing 8448619 (Bumper, Buffer), rev G, PDF page 25; its application block lists 9390023 M4 beside the M16 and M16A1; user-supplied scan (references/…/Spec_Sheets/M16_Technical_Data_Package.pdf), crops in .cache/buffer/std","via":"user"}}]},"carbine_buffer.pin_d":{"label":"Buffer, the pin through its body and bumper, diameter","kind":"length","measurements":[{"id":"tdp","value":0.122,"unit":"in","pm":0.002,"stated":".120+.004 DIA THRU BUMPER BUFFER-8448619 AT ASSEMBLY","source":{"type":"standard","doc":"US Army TDP drawing 8448615 (Buffer Assembly), rev E, PDF page 31; user-supplied scan (references/…/Spec_Sheets/M16_Technical_Data_Package.pdf), crops in .cache/buffer/std","via":"user"},"note":"The hole, drilled through the bumper at assembly through the body's own holes: one-sided (.120 to .124), the middle here. The pin is 8448521-1."},{"id":"model","value":0.131,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Weight_Roll_Pin.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the roll pin's cylinder, r 0.0655","via":"user"}}],"adopt":{"from":"tdp","reason":"The Army's drawing of the assembly."}},"carbine_buffer.pin_from_open_end":{"label":"Buffer, the pin's axis ahead of the body's open end","kind":"length","measurements":[{"id":"tdp","value":0.24,"unit":"in","pm":0.005,"stated":".240","source":{"type":"standard","doc":"US Army TDP drawing 8448616 (Body, Buffer: the RIFLE buffer's), rev F, Section A-A, PDF page 28; user-supplied scan (references/…/Spec_Sheets/M16_Technical_Data_Package.pdf), crops in .cache/buffer/std","via":"user"},"note":"The rifle buffer's body: the Army's package has no drawing of a carbine buffer (9390023 is named on its bumper's, weight's and disc's drawings and not included)."},{"id":"model","value":0.2353,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Weight_Body.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the cross hole's axis, y 2.6187 of a body 2.854 long","via":"user"}}],"adopt":{"from":"tdp","reason":"The Army's drawing of the rifle body's cross hole; the reference model's carbine body has it within 0.005."}},"carbine_action_spring.wire_d":{"label":"Action spring, wire diameter","kind":"length","measurements":[{"id":"tdp","value":0.072,"unit":"in","pm":0.001,"stated":"WIRE DIA: .072±.001","source":{"type":"standard","doc":"US Army TDP drawing 8448629 (Spring, Action: the RIFLE's), rev C, PDF page 36, spring data; user-supplied scan (references/…/Spec_Sheets/M16_Technical_Data_Package.pdf), crops in .cache/buffer/std","via":"user"},"note":"The rifle's spring, the only one the Army's package draws. BCM says of its carbine spring only \"Made to M4A1 Mil-Spec specifications\"."},{"id":"model","value":0.07,"unit":"in","pm":0.0005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/Springs/Carbine_Buffer/STEP/Carbine_Buffer_Spring.stp (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the swept circle, r 0.035","via":"user"}}],"adopt":{"from":"tdp","reason":"The Army's drawing of the rifle's spring; the reference model draws its carbine and rifle springs alike, with a wire two thousandths thinner."}},"carbine_action_spring.od":{"label":"Action spring, outside diameter of its coils","kind":"length","measurements":[{"id":"tdp","value":0.94,"unit":"in","pm":0.015,"stated":".940 DIA±.015","source":{"type":"standard","doc":"US Army TDP drawing 8448629 (Spring, Action: the RIFLE's), rev C, PDF page 36; user-supplied scan (references/…/Spec_Sheets/M16_Technical_Data_Package.pdf), crops in .cache/buffer/std","via":"user"},"note":"The rifle's spring, the only one the Army's package draws. BCM says of its carbine spring only \"Made to M4A1 Mil-Spec specifications\". Its end coils are reduced: \".900 DIA±.015 REDUCE (1) COIL BOTH ENDS\"."},{"id":"table","value":0.94,"unit":"in","pm":0.005,"stated":"Buffer Spring (carbine) 1 10.7 .940 36","source":{"type":"spec","publisher":"review","name":"AR-15_M16_Spring_Data.PNG, a table of springs in the CAD reference set the user supplied (references/…/Spec_Sheets/); no source is named in it","via":"user"}},{"id":"model","value":0.94,"unit":"in","pm":0.0005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/Springs/Carbine_Buffer/STEP/Carbine_Buffer_Spring.stp (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the helix's radius and the wire's","via":"user"}}],"adopt":{"from":"tdp","reason":"The Army's drawing; the table's carbine row and the reference model's carbine spring have the same."}},"carbine_action_spring.end_coil_od":{"label":"Action spring, outside diameter of the one reduced coil at each end","kind":"length","measurements":[{"id":"tdp","value":0.9,"unit":"in","pm":0.015,"stated":".900 DIA±.015 REDUCE (1) COIL BOTH ENDS","source":{"type":"standard","doc":"US Army TDP drawing 8448629 (Spring, Action: the RIFLE's), rev C, PDF page 36; user-supplied scan (references/…/Spec_Sheets/M16_Technical_Data_Package.pdf), crops in .cache/buffer/std","via":"user"},"note":"The rifle's spring, the only one the Army's package draws. BCM says of its carbine spring only \"Made to M4A1 Mil-Spec specifications\"."}]},"carbine_action_spring.free_length":{"label":"Carbine action spring, free length","kind":"length","measurements":[{"id":"table","value":10.7,"unit":"in","pm":0.05,"stated":"Buffer Spring (carbine) 1 10.7 .940 36","source":{"type":"spec","publisher":"review","name":"AR-15_M16_Spring_Data.PNG, a table of springs in the CAD reference set the user supplied (references/…/Spec_Sheets/); no source is named in it","via":"user"}},{"id":"model","value":10.77,"unit":"in","pm":0.01,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/Springs/Carbine_Buffer/STEP/Carbine_Buffer_Spring.stp (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the helix evaluated end to end: 10.700 between the wire's centres, 10.770 over the wire","via":"user"}}],"adopt":{"from":"table","reason":"The table's figure, which the reference model's carbine spring was drawn to (its wire's centres are 10.700 apart). Neither says where it is from: the rifle's is 12.50 REF on the Army's drawing, and both give the rifle's as 12.5."}},"carbine_action_spring.coils":{"label":"Carbine action spring, total coils","kind":"count","measurements":[{"id":"table","value":36,"unit":"count","stated":"Buffer Spring (carbine) 1 10.7 .940 36","source":{"type":"spec","publisher":"review","name":"AR-15_M16_Spring_Data.PNG, a table of springs in the CAD reference set the user supplied (references/…/Spec_Sheets/); no source is named in it","via":"user"}},{"id":"model","value":37.5,"unit":"count","pm":0.1,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/Springs/Carbine_Buffer/STEP/Carbine_Buffer_Spring.stp (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the helix evaluated: 37.56 turns free, 37.50 in the compressed copy the assembly has","via":"user"}}],"adopt":{"from":"model","reason":"A count read off a helix, against a table's round figure with no source; the two are a turn and a half apart, and a maker's own spring is counted on its own photo (the rifle's is 44 REF on the Army's drawing, 44 in the table, 45.56 in the model)."}},"density.aluminium":{"label":"Aluminium (6061 or 7075): what a cubic inch weighs","kind":"mass","measurements":[{"id":"alcoa-6061","value":0.098,"unit":"lb","stated":"Density: 0.098 lb./in.3","source":{"type":"spec","publisher":"manufacturer","name":"Alcoa, Alloy 6061: Understanding Extruded Aluminum Alloys (data sheet, archived copy)","url":"https://web.archive.org/web/20061020230114/http://www.alcoa.com/adip/catalog/pdf/Extruded_Alloy_6061.pdf","retrieved":"2026-10-01","via":"harvest"}},{"id":"wikipedia-6061","value":44.25,"unit":"g","pm":0.08,"stated":"Density (ρ) 2.70 g/cm3","source":{"type":"spec","publisher":"review","name":"Wikipedia, 6061 aluminium alloy","url":"https://en.wikipedia.org/wiki/6061_aluminium_alloy","retrieved":"2026-10-01","via":"harvest"},"note":"2.70 g/cm³ times the 16.387 cm³ in a cubic inch; the ± is half its last digit."},{"id":"wikipedia-7075","value":0.102,"unit":"lb","stated":"Density (ρ) 2.81 g/cm3 (0.102 lb/cu in)","source":{"type":"spec","publisher":"review","name":"Wikipedia, 7075 aluminium alloy","url":"https://en.wikipedia.org/wiki/7075_aluminium_alloy","retrieved":"2026-10-01","via":"harvest"}}],"adopt":{"from":"alcoa-6061","reason":"A producer's sheet for the alloy extrusions are usually made of, and Nordic's receiver is an extrusion. 7075 is the visible heavier end."},"note":"For the centre-of-mass estimate (M7): a part's piece whose volume is dimensioned weighs its volume times this. Nordic says only \"Aluminum upper\" and \"Aluminum slim diameter hand guard\"; the two alloys a receiver or handguard is usually made of are 4% apart, and both are here."},"density.aluminium_7075":{"label":"Aluminium, alloy 7075: what a cubic inch weighs","kind":"mass","measurements":[{"id":"wikipedia-7075","value":0.102,"unit":"lb","stated":"Density (ρ) 2.81 g/cm3 (0.102 lb/cu in)","source":{"type":"spec","publisher":"review","name":"Wikipedia, 7075 aluminium alloy","url":"https://en.wikipedia.org/wiki/7075_aluminium_alloy","retrieved":"2026-10-01","via":"harvest"}}],"note":"For the weight of a part its maker says is 7075 and states no weight for (2026-10-12, D82: BCM's receiver extension): its dimensioned volume times this. 4% over the 6061 that density.aluminium adopts."},"density.stainless_416":{"label":"Stainless steel (type 416): what a cubic inch weighs","kind":"mass","measurements":[{"id":"azom","value":127,"unit":"g","pm":0.08,"stated":"Density 7.75 g/cm³","source":{"type":"spec","publisher":"review","name":"AZoM, Grade 416 Stainless Steel: Properties, Fabrication and Applications","url":"https://www.azom.com/article.aspx?ArticleID=12572","retrieved":"2026-10-01","via":"harvest"},"note":"7.75 g/cm³ times the 16.387 cm³ in a cubic inch; the ± is half its last digit."},{"id":"rolled-alloys","value":0.276,"unit":"lb","stated":"Density: 0.276lb/in³","source":{"type":"spec","publisher":"manufacturer","name":"Rolled Alloys, 416 Stainless data sheet","url":"https://www.rolledalloys.com/wp-content/uploads/416_stainless-steel-data-sheet-rolled-alloys.pdf","retrieved":"2026-10-01","via":"harvest"}}],"adopt":{"from":"azom","reason":"The handbook figure for the grade; a stockholder's sheet reads 1.4% lighter and stays as the lower end."},"note":"Nordic says \"Stainless steel barrel and bolt\" and names no grade; 416 is the usual barrel stainless. The two sheets differ by 1.4%."},"density.steel":{"label":"Steel (grade not stated): what a cubic inch weighs","kind":"mass","measurements":[{"id":"wikipedia","value":4.565,"unit":"oz","pm":0.085,"stated":"The density of steel varies based on the alloying constituents but usually ranges between 7,750 and 8,050 kg/m3 (484 and 503 lb/cu ft), or 7.75 and 8.05 g/cm3 (4.48 and 4.65 oz/cu in).","source":{"type":"spec","publisher":"review","name":"Wikipedia, Steel","url":"https://en.wikipedia.org/wiki/Steel","retrieved":"2026-10-12","via":"harvest"},"note":"The middle of the stated 4.48 to 4.65 oz to the cubic inch; the ± is half that range."}],"note":"For the weight of a steel part whose maker states none (2026-10-12, D82: a castle nut, an end plate, an action spring): its dimensioned volume times this. The range steels lie in; the grade of none of those parts is stated."},"density.polymer":{"label":"Polymer (a polyamide: nylon 66, unfilled): what a cubic inch weighs","kind":"mass","measurements":[{"id":"wikipedia-pa66","value":18.68,"unit":"g","pm":0.008,"stated":"Density 1.140 g/ml (Zytel)","source":{"type":"spec","publisher":"review","name":"Wikipedia, Nylon 66 (its chemical infobox)","url":"https://en.wikipedia.org/wiki/Nylon_66","retrieved":"2026-10-19","via":"harvest"},"note":"1.140 g/ml (DuPont's Zytel) times the 16.387 ml in a cubic inch is 18.68 g; the ± is half its last digit."}],"note":"For the weight of a moulded polymer part whose maker states none (2026-10-20, batch 14: BCM's KAG, whose maker says only \"high quality, impact resistant polymers\"): its model's volume times this. No maker on file names its grade; a glass-filled polyamide is heavier (by up to 0.2 g/ml), and a part's weight worked out from this says so in its own ±. Moulded grips with steel nuts and screws in them weigh more than their models' volume as this: BCM's VG Mod 3 1.35 times it, Magpul's MVG 1.57 times."},"ar15.gas_tube_above_bore":{"label":"The gas tube's axis above the bore's axis","kind":"length","measurements":[{"id":"tdp","value":0.78,"unit":"in","pm":0.018,"stated":".780 ±.018","source":{"type":"standard","doc":"US Army TDP drawing 8448522 (Upper Receiver and Barrel Assembly), PDF page 190, Section A-A at 1/1"},"note":"From the upper receiver's 1.000 bore (-P-, 8448524). The carrier's key (8448506) puts its stem's axis .786 above the carrier's: inside it."}]},"ar15.gas_tube_hole_from_front":{"label":"The gas tube's gas hole behind the tube's front end","kind":"length","measurements":[{"id":"tdp","value":0.605,"unit":"in","pm":0.004,"stated":".605 REF","source":{"type":"standard","doc":"US Army TDP drawing 8448567 (Gas Tube Assembly), rev F, PDF page 144: the .125 gas hole .605 REF from the tube's front end, which is the pin hole's .187 ±.003 from that end and the pin hole to the gas hole .418 ±.002 (as read for bcm-750-gas-block.pin_to_port, 2026-10-05); user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"}}],"note":"The tube's hole lies over the block's port, so its front end stands this far ahead of the port, in the block's blind end, and its rear end that much less far into the receiver (2026-10-05: tubes were drawn beginning at the port, 0.6 in too deep in the receiver; the model review of that day)."},"ar15.charging_handle_t_width":{"label":"The AR-15 charging handle's T, side to side","kind":"length","measurements":[{"id":"tdp","value":2.1,"unit":"in","pm":0.05,"source":{"type":"standard","doc":"US Army TDP drawing 8448518 (Handle, Charging), rev G, scale 2/1, PDF page 128: the plan view and Section G-G, scaled at 316 px/in (665 and 656 px)"}}],"note":"Not a callout: the T is 'AS FORGED' and its forging drawing (D8448647) isn't in the package; scaled off the machined drawing. An AR-pattern handle that takes the standard latches has this T."},"ar15.charging_handle_seat_x":{"label":"The AR-15 upper's open notch under its rail's rear end, its front wall, X ahead of the takedown pin: where a charging handle's shoulder stops","kind":"length","measurements":[{"id":"tdp","value":0.075,"unit":"in","pm":0.015,"source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: side elevation, scaled (the notch has no callout in this view); user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"},"note":"On the 6600 px scan the two lug holes, fitted as circles, are 1966 px apart (308.4 px/in over std.ar15.pin_spacing) and the notch's front wall (column 2427.5) is 21.5 px ahead of the takedown hole's centre: 0.070. From the rear face's line, 217 px behind the wall, it is 0.083. Between the two; ± covers both."}],"note":"Not a callout on the machined drawing's side elevation: scaled. Three forged receivers' own photos read it 0.068 to 0.092 by its near edge (bcm-m4-upper, expo-arms-stripped-upper, aero-m4e1-threaded-upper: handle_seat_x). Two things point to about 0.097: the reference model's channel ends 5.993 ahead of the pin and the handle is 5.895 long; and the arc in the handle's T (8448518: .437 R, apex .780 behind the shoulder) is concentric with the receiver's .375 R rear contour at that seat."},"ar15.charging_handle_channel_rear_half_width":{"label":"The AR-15 upper's charging handle channel through its rear face, half its width: from the rear face to the rear round","kind":"length","measurements":[{"id":"tdp","value":0.209,"unit":"in","pm":0.003,"stated":".418 FOR 1.325 LENGTH","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 2 of 2, rev G: View G-G; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p109","via":"user"},"note":"Half of .418 (three places: the title block's ±.005, half of it here). 1.325 from the rear face reaches the rear round."},{"id":"a2","value":0.209,"unit":"in","pm":0.003,"stated":".413 +.010 FOR 1.320 +.010 LENGTH","source":{"type":"standard","doc":"US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-2/3, bottom view; user-supplied scan (Distribution Statement F), PDF page 124","via":"user"},"note":"Half of .413 to .423."},{"id":"model","value":0.208,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; .cache/keyway/cad_key.py rear): planes z ±0.208 from the rear face to x 0.510, y 1.337 to 1.903","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's; the A2's drawing gives the same and the reference model a thousandth less."},"note":"The slot the handle's shaft (.400) runs out of the receiver's rear in, from the bore up to the channel's roof. The guide lugs' tier doesn't run back through it: a handle comes out by being drawn back until its lugs are in the rear round (std.ar15.charging_handle_channel_rear_round_x), and then down into the bore."},"ar15.charging_handle_channel_slot_half_width":{"label":"The AR-15 upper's charging handle channel: the slot under the guide lugs' tier, half its width","kind":"length","measurements":[{"id":"model","value":0.205,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/keyway/cad_key.py): planes z ±0.205 from y 1.338 to 1.586, x 0.847 to 5.556, each ending on a round","via":"user"}}],"note":"Between the bore and the tier, from round to round: where the handle's hook (.400) and the carrier's key (.4005) run."},"ar15.charging_handle_channel_tier_half_width":{"label":"The AR-15 upper's charging handle channel: the guide lugs' tier, half its width","kind":"length","measurements":[{"id":"tdp","value":0.25,"unit":"in","pm":0.005,"stated":".50","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 2 of 2, rev G: View G-G, the channel's width ahead of the rear round; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p109","via":"user"},"note":"Two places: ±.01 by the title block, half of it here."},{"id":"model","value":0.25,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/keyway/cad_key.py): planes z ±0.250 from y 1.586 to 1.711, x 0.769 to 5.634, each ending on a round","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's; the reference model has the same."},"note":"The handle's two guide lugs (8448518: .488 across, .119 high) ride in it, on its floor."},"ar15.charging_handle_channel_top_half_width":{"label":"The AR-15 upper's charging handle channel: the tier over the guide lugs' up to the roof, half its width","kind":"length","measurements":[{"id":"model","value":0.22,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/keyway/cad_key.py): planes z ±0.220 from y 1.711 to 1.903, x 0.827 to 5.576, each ending on a round","via":"user"}}],"note":"Where the handle's shaft (.400) runs, and the top of the carrier's key's tube."},"ar15.charging_handle_channel_floor_y":{"label":"The AR-15 upper's charging handle channel: the guide lugs' tier, its floor above the pin line","kind":"length","measurements":[{"id":"tdp","value":1.5845,"unit":"in","pm":0.0045,"stated":"1.336 ±.003","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 2 of 2, rev G: Section B-B, from the underside (the deck it sits on, std.ar15.deck_y) to the tier's floor; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p109","via":"user"},"note":"1.336 over the deck's .2485. Checked on the scan: the bore's circle (155 px radius, .500) puts the underside's line 0.633 below the bore's axis, the deck's place."},{"id":"model","value":1.586,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/keyway/cad_key.py): planes y 1.586 at z ±0.205 to ±0.250, x 0.769 to 5.634","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's; the reference model's is 0.0015 higher."},"note":"What a handle rides on, by its guide lugs (std.ar15.charging_handle_axis_y)."},"ar15.charging_handle_channel_tier_top_y":{"label":"The AR-15 upper's charging handle channel: the guide lugs' tier, its top above the pin line","kind":"length","measurements":[{"id":"tdp","value":1.7115,"unit":"in","pm":0.0065,"stated":".125 +.004","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 2 of 2, rev G: Section B-B, the tier's height over its floor (std.ar15.charging_handle_channel_floor_y); user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p109","via":"user"},"note":"The floor's 1.5845 and the middle of .125 to .129."},{"id":"model","value":1.711,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/keyway/cad_key.py): planes y 1.711 at z ±0.220 to ±0.250, x 0.769 to 5.634","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's; the reference model's is within its ±."}},"ar15.charging_handle_channel_roof_y":{"label":"The AR-15 upper's charging handle channel: its roof above the pin line","kind":"length","measurements":[{"id":"tdp","value":1.9085,"unit":"in","pm":0.0045,"stated":"1.660 ±.003","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 2 of 2, rev G: Section A-A, from the underside (std.ar15.deck_y) to the roof over the channel, along it; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p109","via":"user"},"note":"1.660 over the deck's .2485. The drawing's is the A1's receiver, its roof the thin wall under the carry handle."},{"id":"model","value":1.903,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/keyway/cad_key.py): the plane y 1.903 from the rear face to x 5.993, z ±0.266","via":"user"},"note":"A flat top's, under its rail."}],"adopt":{"from":"tdp","reason":"The drawing's (D49); the reference model, a flat top, has it 0.0055 lower: inside the two ±, and either is 0.02 over a handle riding on its lugs (std.ar15.charging_handle_axis_y and the handle's .2985)."}},"ar15.charging_handle_channel_rear_round_x":{"label":"The AR-15 upper's charging handle channel: its rear round's axis, X (an upright cylinder the tiers end on)","kind":"length","measurements":[{"id":"model","value":0.676,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/keyway/cad_key.py rear): a cylinder r 0.2665 about an upright axis at x 0.676, z 0, from y 1.305 to 1.903: each tier's walls end on it (the tier's ±0.250 at x 0.769, the top tier's ±0.220 at 0.827, the slot's ±0.205 at 0.847)","via":"user"}}],"note":"Where a handle drawn back has room for its guide lugs to leave the tier: the round is wider than the tier (std.ar15.charging_handle_channel_round_r)."},"ar15.charging_handle_channel_front_round_x":{"label":"The AR-15 upper's charging handle channel: its front round's axis, X","kind":"length","measurements":[{"id":"model","value":5.726,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/keyway/cad_key.py): a cylinder r 0.2665 about an upright axis at x 5.726, z 0, from y 1.305 to 1.903: the slot's ±0.205 ends on it at x 5.556, the top tier's at 5.576, the tier's at 5.634","via":"user"}}]},"ar15.charging_handle_channel_round_r":{"label":"The AR-15 upper's charging handle channel: its two upright rounds' radius","kind":"length","measurements":[{"id":"model","value":0.2665,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/keyway/cad_key.py): the two upright cylinders, 0.2665 at both ends","via":"user"}}]},"ar15.charging_handle_axis_y":{"label":"Where a charging handle lies in an AR-15 upper: its axis (its shaft's mid-thickness) above the pin line","kind":"length","measurements":[{"id":"standard","value":1.7338,"unit":"in","pm":0.0063,"source":{"type":"derived","expr":"{std.ar15.charging_handle_channel_floor_y} + {aero-charging-handle.shaft_thickness} / 2","via":"user"}}],"note":"A handle rides on its two guide lugs on the tier's floor; its shaft is the Army's drawing's .2985 (8448518, as aero-charging-handle.shaft_thickness records it, the catalog's mil-spec handle). Its top is then 0.0255 under the roof, its lugs' tops 0.008 under the tier's, and its block's corners clear of the notch's front wall's (its 47 degrees over .083 to the receiver's 45). Every upper's handle_channel anchor stands here (2026-10-20: each read its own off a see-through notch, BCM's 0.044 high)."},"ar15.charging_handle_notch_floor_y":{"label":"The AR-15 upper's open notch under its rail's rear end (where a charging handle's block lies): its floor above the pin line","kind":"length","measurements":[{"id":"model","value":1.571,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/keyway/cad_key.py rear): planes y 1.571 at z ±0.208 to ±0.318 from the rear face to x 0.007, where a 45 degree face rises to the front wall (std.ar15.charging_handle_notch_chamfer)","via":"user"},"note":"The Army's drawing scales the notch 0.31 to 0.32 high (std.ar15.charging_handle_seat_x's reading): 1.57 to 1.58 under the roof."}],"note":"Across the receiver behind the notch's front wall, beside the rear slot. A handle riding on its guide lugs (std.ar15.charging_handle_axis_y) has its block's underside 0.0135 over it. The upper's photos read the see-through's lower edge 1.595 to 1.6 (each upper's notch, within their ±0.03): at that height a handle's block stood a hundredth in it in every one (2026-10-20)."},"ar15.charging_handle_notch_roof_y":{"label":"The AR-15 upper's open notch under its rail's rear end: its roof (the rail's tongue's underside) above the pin line","kind":"length","measurements":[{"id":"model","value":1.89,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/keyway/cad_key.py rear): planes y 1.890 at z ±0.208 to ±0.318 from x -0.569 to 0.010, where a 45 degree face comes down to the front wall","via":"user"},"note":"A handle riding on its guide lugs has its top 0.007 under it."}]},"ar15.charging_handle_notch_chamfer":{"label":"The AR-15 upper's open notch: its front wall's two corners, cut back at 45 degrees, how far","kind":"length","measurements":[{"id":"model","value":0.083,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/keyway/cad_key.py rear): planes n(-0.707, ±0.707, 0) from (x 0.007, y 1.571) to (0.090, 1.654) and from (0.090, 1.809) to (0.010, 1.890): 0.083 and 0.080","via":"user"}}],"note":"The handle's block's front corners are broken at 47 degrees over .083 (8448518), and clear these."},"ar15.rail_tongue_half_width":{"label":"An AR-15 flat top's rail behind its head: the tongue, half its width","kind":"length","measurements":[{"id":"model","value":0.318,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/keyway/cad_key.py rear): planes z ±0.318 from x -0.478 to 0.277, y 1.870 (left) and 1.885 (right) to 2.090, the rail's top","via":"user"}}],"note":"Upright sides from the notch's roof under it to the rail's top; just inside the head's top flat (.656 across: lib.rail_head, from std.picatinny.*)."},"ar15.rail_tongue_end_r":{"label":"An AR-15 flat top's rail tongue: the radius of its rounded rear end, in plan","kind":"length","measurements":[{"id":"model","value":0.4175,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/keyway/cad_key.py rear): an upright cylinder r 0.4175 about x -0.207, z 0, from y 1.890 to 2.090, x -0.625 to -0.478, meeting the tongue's sides at z ±0.318","via":"user"}}],"note":"Its centre on the receiver's centre line this far ahead of the rail's rearmost point (each upper's rail_tongue_rear_x)."},"ar15.rail_tongue_front_x":{"label":"An AR-15 flat top's rail tongue: where its sides end and the rounds out to the head's width begin, X","kind":"length","measurements":[{"id":"model","value":0.277,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/keyway/cad_key.py rear): the tongue's planes z ±0.318 end at x 0.277, where two upright cylinders (std.ar15.rail_tongue_fillet_r) about (0.277, ±0.466) begin","via":"user"}}]},"ar15.rail_tongue_fillet_r":{"label":"An AR-15 flat top's rail tongue: the radius of the two concave rounds from its sides out to the head's width","kind":"length","measurements":[{"id":"model","value":0.1476,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/keyway/cad_key.py rear): upright cylinders r 0.1476 about (x 0.277, z ±0.466), from y 1.885 to 2.090, x 0.277 to 0.417: tangent to the tongue's sides and out to the head's widest at x 0.417","via":"user"}}]},"ar15.rail_tongue_shoulder_x":{"label":"An AR-15 flat top's rail: where its head is whole again ahead of the tongue, X (the app's rail head begins here: each forging's rail_rear_x)","kind":"length","measurements":[{"id":"derived","value":0.4165,"unit":"in","pm":0.006,"source":{"type":"derived","expr":"{std.ar15.rail_tongue_front_x} + sqrt({std.ar15.rail_tongue_fillet_r} * {std.ar15.rail_tongue_fillet_r} - ({std.ar15.rail_tongue_half_width} + {std.ar15.rail_tongue_fillet_r} - {std.picatinny.top_width} / 2) * ({std.ar15.rail_tongue_half_width} + {std.ar15.rail_tongue_fillet_r} - {std.picatinny.top_width} / 2))","via":"user"},"note":"Where the round from the tongue's side meets the standard's widest (.835 across); the reference model's own faces end at 0.417."}]},"ar15.charging_handle_latch_slot_wall":{"label":"The AR-15 upper's charging handle latch slot: the wall left between it and the notch's front wall (an upper's handle_seat_x)","kind":"length","measurements":[{"id":"tdp","value":0.156,"unit":"in","pm":0.005,"stated":".156","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: Section D-D (cut along the notch's centre line, View C-C: the left wall at the rear); user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}}]},"ar15.charging_handle_latch_slot_length":{"label":"The AR-15 upper's charging handle latch slot, along the receiver (its upper and lower ends full rounds of half this)","kind":"length","measurements":[{"id":"tdp","value":0.195,"unit":"in","pm":0.005,"stated":".195","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: Section D-D (View C-C marks its ends FULL R); user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"}},{"id":"model","value":0.192,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/batch123/bcm-m4-upper/cad_ch.py): two rounds about z, r 0.0960, at (x 0.329, y 1.616) and (x 0.329, y 1.839), from the wall's face at z -0.318 in to the slot's floor at -0.251; the flat between them from x 0.233 to 0.425","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's; the reference model's is within its ±."}},"ar15.charging_handle_latch_slot_bottom_y":{"label":"The AR-15 upper's charging handle latch slot: its lower end above the pin line","kind":"length","measurements":[{"id":"model","value":1.52,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"as std.ar15.charging_handle_latch_slot_length: the lower round's centre at y 1.616, less its r 0.0960","via":"user"},"note":"BCM's own photo reads 1.527 ± 0.012 (bcm-m4-upper.latch_slot_bottom_y)."}]},"ar15.charging_handle_latch_slot_top_y":{"label":"The AR-15 upper's charging handle latch slot: its upper end above the pin line","kind":"length","measurements":[{"id":"model","value":1.935,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"as std.ar15.charging_handle_latch_slot_length: the upper round's centre at y 1.839, plus its r 0.0960","via":"user"},"note":"BCM's own photo reads 1.926 ± 0.012 (bcm-m4-upper.latch_slot_top_y)."}]},"ar15.charging_handle_latch_slot_floor":{"label":"The AR-15 upper's charging handle latch slot: the wall left under it, between its floor and the channel's rear slot","kind":"length","measurements":[{"id":"tdp","value":0.045,"unit":"in","pm":0.005,"stated":".045","source":{"type":"standard","doc":"US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: Section D-D; user-supplied scan (Distribution Statement F, Colt proprietary notice), references/tdp p108","via":"user"},"note":"Taken as the strip of wall under the slot's floor: the two lines it is drawn between are the floor's and the wall's inner face."},{"id":"model","value":0.043,"unit":"in","pm":0.004,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Unthreaded_Components/Unthreaded Components_split/Upper_Receiver_Body.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging)","method":"its faces read from the STEP text in the rifle frame its lug holes set (.cache/batch123/bcm-m4-upper/cad_ch.py): the slot's floor is a plane at z -0.251 from x 0.233 to 0.425, y 1.520 to 1.940, and the channel's wall beside it at z -0.208 (from the rear face to x 0.510)","via":"user"}}],"adopt":{"from":"tdp","reason":"The drawing's; the reference model's is within its ±."}},"ar15.carrier_length":{"label":"AR-15 bolt carrier, length","kind":"length","measurements":[{"id":"tdp","value":6.672,"unit":"in","pm":0.005,"stated":"6.672 ±.005","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the side elevation; user-supplied scan","via":"user"},"note":"The tail's rear face to the front (bolt) face."}]},"ar15.carrier_rail_od":{"label":"AR-15 bolt carrier, the diameter its rails are ground to","kind":"length","measurements":[{"id":"tdp","value":0.994,"unit":"in","pm":0.0005,"stated":".9945 DIA -.0010 GRIND AFTER HEAT TREAT","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the end view; user-supplied scan","via":"user"},"note":"The bearing surfaces of the front part only: a pad on top and a rail low on each side. The rest of the carrier is .930 (carrier_body_od)."}]},"ar15.carrier_body_od":{"label":"AR-15 bolt carrier, the body's and the tail's diameter","kind":"length","measurements":[{"id":"tdp","value":0.93,"unit":"in","pm":0.005,"stated":".930 DIA (-M-)","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the side elevation (the tail); sheet 2, Section X-X has \".465 R, BOTH SIDES\" for the front part's sides; user-supplied scan","via":"user"},"note":"Taken as one diameter the whole length: the tail's callout and the front part's side radius are the same .930."}]},"ar15.carrier_rear_chamfer":{"label":"AR-15 bolt carrier, the chamfer at the tail's rear","kind":"length","measurements":[{"id":"tdp","value":0.03,"unit":"in","pm":0.01,"stated":".03","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the side elevation; user-supplied scan","via":"user"},"note":"With 30° ±2° (carrier_rear_chamfer_angle)."}]},"ar15.carrier_rear_chamfer_angle":{"label":"AR-15 bolt carrier, the angle of the tail's rear chamfer","kind":"angle","measurements":[{"id":"tdp","value":30,"unit":"deg","pm":2,"stated":"30° ±2°","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the side elevation; user-supplied scan","via":"user"},"note":"From the tail's surface."}]},"ar15.carrier_tail_front":{"label":"AR-15 bolt carrier, the tail's front shoulder, from the front face","kind":"length","measurements":[{"id":"tdp","value":5.1,"unit":"in","pm":0.01,"stated":"5.10","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the side elevation (5.100 REF on the top view); user-supplied scan","via":"user"},"note":"Where the cut across the top begins: behind it the carrier is the full round tail."}]},"ar15.carrier_top_cut_length":{"label":"AR-15 bolt carrier, the cut across the top behind the key, its length","kind":"length","measurements":[{"id":"tdp","value":2.07,"unit":"in","pm":0.01,"stated":"2.07","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the side elevation; user-supplied scan","via":"user"},"note":"From the tail's shoulder forward to the cut's front wall, the .12 corner radius at the foot of each."}]},"ar15.carrier_cut_corner_r":{"label":"AR-15 bolt carrier, the corner radius of the top cut","kind":"length","measurements":[{"id":"tdp","value":0.12,"unit":"in","pm":0.01,"stated":".12 R, 3 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the side elevation; user-supplied scan","via":"user"}}]},"ar15.carrier_slab_height":{"label":"AR-15 bolt carrier, what is left between the top cut and the bottom cut","kind":"length","measurements":[{"id":"tdp","value":0.5,"unit":"in","pm":0.01,"stated":".50","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the side elevation; user-supplied scan","via":"user"},"note":"Taken as central on the axis (.25 each way): the bottom cut's own depth, .215 from the .930 diameter, puts its roof .25 below the axis, and the top's floor measures the same on the sheet."}]},"ar15.carrier_bottom_cut_depth":{"label":"AR-15 bolt carrier, the cut across the bottom (the hammer's), its depth","kind":"length","measurements":[{"id":"tdp","value":0.215,"unit":"in","pm":0.005,"stated":".215","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the side elevation; user-supplied scan","via":"user"},"note":"From the bottom of the .930 diameter."}]},"ar15.carrier_bottom_cut_rear":{"label":"AR-15 bolt carrier, the bottom cut's rear shoulder, from the front face","kind":"length","measurements":[{"id":"tdp","value":5.0965,"unit":"in","pm":0.0065,"stated":"5.0965 ±.0065","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the side elevation; user-supplied scan","via":"user"},"note":"Taken as the bottom cut's rear shoulder (the dimension is under the view, beside the bottom cut's own 2.30 and 2.35); the slot through the carrier is drawn ending against it."}]},"ar15.carrier_groove_runout_from_shoulder":{"label":"AR-15 bolt carrier, where the grooves beside the rib begin to run out, ahead of the tail's shoulder","kind":"length","measurements":[{"id":"tdp","value":2.35,"unit":"in","pm":0.01,"stated":"2.35","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the side elevation; user-supplied scan","via":"user"},"note":"Taken as the centre of the 1.500 R the two grooves run out on (carrier_groove_runout_r): behind it they shallow into the bottom cut's roof. 2.30 beside it is the front part's rear face (2.81 from the front on Section C-C), where the bottom cut ends. The first reading here had the 1.500 R as the bottom cut's own run-out; the user's reference CAD set has it as the grooves', centred at the front part's rear face, and the photos of two makers' carriers show the cut's roof flat to that face."}]},"ar15.carrier_groove_runout_r":{"label":"AR-15 bolt carrier, the radius the two grooves beside the rib run out on, to the rear","kind":"length","measurements":[{"id":"tdp","value":1.5,"unit":"in","pm":0.015,"stated":"1.500R ±.015, 2 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the side elevation; user-supplied scan","via":"user"},"note":"One for each groove: the cutter's radius, taken to the groove's roof."}]},"ar15.carrier_bottom_cut_rear_r":{"label":"AR-15 bolt carrier, the bottom cut's rear corner radius","kind":"length","measurements":[{"id":"tdp","value":0.125,"unit":"in","pm":0.005,"stated":".125 R","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the side elevation; user-supplied scan","via":"user"}}]},"ar15.carrier_slot_width":{"label":"AR-15 bolt carrier, the slot through its middle (top to bottom), width","kind":"length","measurements":[{"id":"tdp","value":0.5,"unit":"in","pm":0.01,"stated":".50 DIA END MILL THRU BOTH SIDES","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the top view; user-supplied scan","via":"user"}}]},"ar15.carrier_slot_travel":{"label":"AR-15 bolt carrier, the slot through its middle, between its ends' centres","kind":"length","measurements":[{"id":"tdp","value":1.75,"unit":"in","pm":0.01,"stated":"1.75 CUTTER TRAVEL","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the top view; user-supplied scan","via":"user"}}]},"ar15.carrier_tail_bore":{"label":"AR-15 bolt carrier, the tail's bore","kind":"length","measurements":[{"id":"tdp","value":0.625,"unit":"in","pm":0.01,"stated":".625 DIA ±.010","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 2 of 2, rev K, PDF page 203: View N-N; user-supplied scan","via":"user"},"note":"The opening at the rear; the bores ahead of it (Section W-W) are inside and aren't drawn."}]},"ar15.carrier_tail_notch_width":{"label":"AR-15 bolt carrier, the notch under the tail's rear, width","kind":"length","measurements":[{"id":"tdp","value":0.156,"unit":"in","pm":0.005,"stated":".156","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 2 of 2, rev K, PDF page 203: View N-N; user-supplied scan","via":"user"}}]},"ar15.carrier_tail_notch_depth":{"label":"AR-15 bolt carrier, the notch under the tail's rear, depth","kind":"length","measurements":[{"id":"tdp","value":0.1,"unit":"in","pm":0.005,"stated":".100","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 2 of 2, rev K, PDF page 203: View N-N; user-supplied scan","via":"user"},"note":"Taken as measured up from the bottom of the .930 diameter; how far forward it runs isn't on the views read (drawn the length of the tail)."}]},"ar15.carrier_key_seat_y":{"label":"AR-15 bolt carrier, the key's seat above the axis","kind":"length","measurements":[{"id":"tdp","value":0.42,"unit":"in","pm":0.002,"stated":".420 ±.002 GRIND AFTER HEAT TREAT","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 2 of 2, rev K, PDF page 203: Section X-X; user-supplied scan","via":"user"},"note":"The floor of the slot the key sits in."}]},"ar15.carrier_key_slot_width":{"label":"AR-15 bolt carrier, the slot the key sits in, width","kind":"length","measurements":[{"id":"tdp","value":0.4035,"unit":"in","pm":0.0015,"stated":".4035 ±.0015 (-U-)","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the top view; user-supplied scan","via":"user"}}]},"ar15.carrier_key_seat_rear":{"label":"AR-15 bolt carrier, the key's seat, its rear end from the front face","kind":"length","measurements":[{"id":"tdp","value":2.74,"unit":"in","pm":0.01,"stated":"2.74","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: Section C-C; user-supplied scan","via":"user"},"note":"Where the .50 R run-out to the rear begins: it reaches the top of the rails' diameter .265 further back, just ahead of the top cut's front wall (5.10 less 2.07)."}]},"ar15.carrier_key_slot_rear":{"label":"AR-15 bolt carrier, the key's slot, the top of its rear ramp from the front face","kind":"length","measurements":[{"id":"tdp","value":2.76,"unit":"in","pm":0.01,"stated":"2.76 REF","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: View Z (alternate method, 45°); user-supplied scan","via":"user"},"note":"The alternate method's end (a 45° ramp from the top cut's front). The one drawn is the other: the seat's .50 R run-out to the rear, which reaches the top just ahead of the top cut's front wall."}]},"ar15.carrier_key_seat_front":{"label":"AR-15 bolt carrier, the key's seat, where its front run-out begins, from the front face","kind":"length","measurements":[{"id":"tdp","value":1.37,"unit":"in","pm":0.01,"stated":"1.37","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: Section C-C; user-supplied scan","via":"user"},"note":"The .50 R run-out reaches the top at 1.105 REF."}]},"ar15.carrier_key_seat_runout_r":{"label":"AR-15 bolt carrier, the key's seat, its front run-out radius","kind":"length","measurements":[{"id":"tdp","value":0.5,"unit":"in","pm":0.01,"stated":".50 R","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: Section C-C; user-supplied scan","via":"user"}}]},"ar15.carrier_key_screw_x":{"label":"AR-15 bolt carrier, the forward key screw's hole, from the front face","kind":"length","measurements":[{"id":"tdp","value":2.055,"unit":"in","pm":0.005,"stated":"2.055","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: Section C-C; user-supplied scan","via":"user"}}]},"ar15.carrier_key_screw_spacing":{"label":"AR-15 bolt carrier, between the two key screws","kind":"length","measurements":[{"id":"tdp","value":0.5,"unit":"in","pm":0.003,"stated":".500 ±.003","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: Section C-C (and the key's own drawing, 8448506); user-supplied scan","via":"user"}}]},"ar15.carrier_pad_edge_angle":{"label":"AR-15 bolt carrier, the top pad's edges, above the horizontal","kind":"angle","measurements":[{"id":"tdp","value":55,"unit":"deg","pm":1,"stated":"55° 2 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the end view; user-supplied scan","via":"user"},"note":"The pad at the rails' diameter lies between them, either side of the key's slot (seen in Section X-X, where the outline steps from .465 R to the full diameter there)."}]},"ar15.carrier_relief_angle":{"label":"AR-15 bolt carrier, the relieved side between the top pad and the lower rail","kind":"angle","measurements":[{"id":"tdp","value":75,"unit":"deg","pm":1,"stated":"75° BOTH SIDES","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the end view; user-supplied scan","via":"user"},"note":"From 55° above the horizontal to 20° below it (\"20° REF\" on Section X-X)."}]},"ar15.carrier_rail_top_drop":{"label":"AR-15 bolt carrier, the lower rails' top, below the top of the rails' diameter","kind":"length","measurements":[{"id":"tdp","value":0.67,"unit":"in","pm":0.005,"stated":".670","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the end view; user-supplied scan","via":"user"},"note":"A level plane on each side: it meets the rails' diameter 20° below the horizontal."}]},"ar15.carrier_pad_front":{"label":"AR-15 bolt carrier, where the top pad begins behind the front face","kind":"length","measurements":[{"id":"tdp","value":0.38,"unit":"in","pm":0.005,"stated":".380","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the side elevation; user-supplied scan","via":"user"},"note":"Ahead of it the top is flat, .095 lower (carrier_front_flat_drop)."}]},"ar15.carrier_front_flat_drop":{"label":"AR-15 bolt carrier, the flat on top at the front, below the top of the rails' diameter","kind":"length","measurements":[{"id":"tdp","value":0.095,"unit":"in","pm":0.01,"stated":".095 ±.010","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the side elevation; user-supplied scan","via":"user"}}]},"ar15.carrier_rib_width":{"label":"AR-15 bolt carrier, the rib under the front part, width","kind":"length","measurements":[{"id":"tdp","value":0.399,"unit":"in","pm":0.006,"stated":".399 ±.006","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the end view; user-supplied scan","via":"user"}}]},"ar15.carrier_rib_bottom_drop":{"label":"AR-15 bolt carrier, the rib's underside, below the top of the rails' diameter","kind":"length","measurements":[{"id":"tdp","value":0.859,"unit":"in","pm":0.004,"stated":".859 ±.004","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the end view; user-supplied scan","via":"user"}}]},"ar15.carrier_rib_chamfer_across":{"label":"AR-15 bolt carrier, the rib's two chamfers, from the far side of the rails' diameter","kind":"length","measurements":[{"id":"tdp","value":0.87,"unit":"in","pm":0.005,"stated":".870 2 PLACES (.373 REF from the axis)","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 2 of 2, rev K, PDF page 203: Section X-X; user-supplied scan","via":"user"},"note":"At 22°30' (carrier_rib_chamfer_angle)."}]},"ar15.carrier_rib_chamfer_angle":{"label":"AR-15 bolt carrier, the angle of the rib's chamfers from the level","kind":"angle","measurements":[{"id":"tdp","value":22.5,"unit":"deg","pm":0.5,"stated":"22°30' ±0°30', 2 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 2 of 2, rev K, PDF page 203: Section X-X; user-supplied scan","via":"user"}}]},"ar15.carrier_rib_rear":{"label":"AR-15 bolt carrier, the front part's underside, its rear end from the front face","kind":"length","measurements":[{"id":"tdp","value":2.81,"unit":"in","pm":0.01,"stated":"2.81","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: Section C-C; user-supplied scan","via":"user"}}]},"ar15.carrier_rib_taper_start":{"label":"AR-15 bolt carrier, where the underside begins to rise toward the rear, from the front face","kind":"length","measurements":[{"id":"tdp","value":1.8,"unit":"in","pm":0.01,"stated":"1.80","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: Section C-C; user-supplied scan","via":"user"}}]},"ar15.carrier_rib_taper_angle":{"label":"AR-15 bolt carrier, the rise of the underside toward the rear","kind":"angle","measurements":[{"id":"tdp","value":4.5,"unit":"deg","pm":0.5,"stated":"4°30' ±0°30'","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: Section C-C; user-supplied scan","via":"user"}}]},"ar15.carrier_groove_r":{"label":"AR-15 bolt carrier, the two grooves beside the rib, radius","kind":"length","measurements":[{"id":"tdp","value":0.078,"unit":"in","pm":0.003,"stated":".078 R ±.003, 2 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the end view; user-supplied scan","via":"user"}}]},"ar15.carrier_groove_angle":{"label":"AR-15 bolt carrier, the grooves beside the rib, below the horizontal","kind":"angle","measurements":[{"id":"tdp","value":45,"unit":"deg","pm":0.5,"stated":"45°0' ±0°30' 2 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the end view; user-supplied scan","via":"user"},"note":"Taken as the direction of each groove's centre from the axis; the centre itself is drawn where the groove touches the rib's side (as Section X-X draws it), which no callout read gives."}]},"ar15.carrier_front_chamfer":{"label":"AR-15 bolt carrier, the chamfer at the front of the lower rails","kind":"length","measurements":[{"id":"tdp","value":0.075,"unit":"in","pm":0.01,"stated":".075 ±.010","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the detail beside the end view (45° ±2°); user-supplied scan","via":"user"}}]},"ar15.carrier_scallop_across":{"label":"AR-15 bolt carrier, the flat on its right side (the vents'), from the far side of the rails' diameter","kind":"length","measurements":[{"id":"tdp","value":0.8125,"unit":"in","pm":0.0075,"stated":".8125 ±.0075","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 2 of 2, rev K, PDF page 203: Section X-X; user-supplied scan","via":"user"},"note":"Measured square to the flat, which leans 22°30' from the upright (carrier_scallop_angle): .315 from the axis (the auxiliary view's depth, .184 REF, is from the rails' diameter)."}]},"ar15.carrier_scallop_angle":{"label":"AR-15 bolt carrier, the lean of the flat on its right side from the upright","kind":"angle","measurements":[{"id":"tdp","value":22.5,"unit":"deg","pm":0.5,"stated":"22°30' ±0°30'","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 2 of 2, rev K, PDF page 203: Section X-X and the auxiliary view above View N-N; user-supplied scan","via":"user"},"note":"It faces to the right and upward."}]},"ar15.carrier_scallop_flat":{"label":"AR-15 bolt carrier, the flat on its right side, its length","kind":"length","measurements":[{"id":"tdp","value":0.375,"unit":"in","pm":0.015,"stated":".375 ±.015 FLAT","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 2 of 2, rev K, PDF page 203: the auxiliary view above View N-N; user-supplied scan","via":"user"}}]},"ar15.carrier_scallop_rear":{"label":"AR-15 bolt carrier, the flat on its right side, its rear end from the front face","kind":"length","measurements":[{"id":"tdp","value":1.5,"unit":"in","pm":0.01,"stated":"1.50","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 2 of 2, rev K, PDF page 203: the auxiliary view above View N-N (1.50 REF to the centre of the .47 R on sheet 1); user-supplied scan","via":"user"}}]},"ar15.carrier_scallop_r":{"label":"AR-15 bolt carrier, the radius at each end of the flat on its right side","kind":"length","measurements":[{"id":"tdp","value":0.47,"unit":"in","pm":0.04,"stated":".47 R +.04, 2 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 2 of 2, rev K, PDF page 203: the auxiliary view above View N-N; user-supplied scan","via":"user"},"note":"Stated + .04 only; the ± here covers it."}]},"ar15.carrier_vent_x":{"label":"AR-15 bolt carrier, the two vent holes, from the front face","kind":"length","measurements":[{"id":"tdp","value":1.34,"unit":"in","pm":0.01,"stated":"1.34","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 2 of 2, rev K, PDF page 203: Section W-W; user-supplied scan","via":"user"},"note":"One level with the axis and one 45° above it (the end view), both in the flat on the right side."}]},"ar15.carrier_vent_d":{"label":"AR-15 bolt carrier, the vent holes' diameter","kind":"length","measurements":[{"id":"tdp","value":0.109,"unit":"in","pm":0.005,"stated":".109 DIA THRU ONE SIDE ONLY, 2 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 2 of 2, rev K, PDF page 203: Section W-W; user-supplied scan","via":"user"}}]},"ar15.carrier_cam_x":{"label":"AR-15 bolt carrier, the cam track's forward end (0°), from the front face","kind":"length","measurements":[{"id":"tdp","value":0.64,"unit":"in","pm":0.005,"stated":".640 (-N-)","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the top view; user-supplied scan","via":"user"}}]},"ar15.carrier_cam_width":{"label":"AR-15 bolt carrier, the cam track's width","kind":"length","measurements":[{"id":"tdp","value":0.3165,"unit":"in","pm":0.003,"stated":".3165 DIA +.0030 ... REMAINDER OF TRACK TO BE GENERATED BY PASSAGE OF A .3165 DIA +.0030 THEORETICAL CYLINDER THROUGH THE COORDINATES","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the top view; user-supplied scan","via":"user"},"note":"Stated + .0030 only."}]},"ar15.carrier_cam_dwell":{"label":"AR-15 bolt carrier, the cam track's advance at 0°","kind":"length","measurements":[{"id":"tdp","value":0.042,"unit":"in","pm":0.002,"stated":"ANGLE 0, ADVANCE .042 (±.002)","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 2 of 2, rev K, PDF page 203: the cam track's table; user-supplied scan","via":"user"},"note":"Rearward of -N-: the track runs straight this far before it turns."}]},"ar15.carrier_cam_advance_20":{"label":"AR-15 bolt carrier, the cam track's advance at 20°","kind":"length","measurements":[{"id":"tdp","value":0.195,"unit":"in","pm":0.002,"stated":"ANGLE 20, ADVANCE .195 (±.002)","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 2 of 2, rev K, PDF page 203: the cam track's table; user-supplied scan","via":"user"},"note":"The table is a straight helix to here (5° .080, 10° .118, 15° .157)."}]},"ar15.carrier_cam_advance":{"label":"AR-15 bolt carrier, the cam track's advance at 22 1/2°","kind":"length","measurements":[{"id":"tdp","value":0.255,"unit":"in","pm":0.002,"stated":"ANGLE 22 1/2, ADVANCE .255 (±.002)","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 2 of 2, rev K, PDF page 203: the cam track's table; user-supplied scan","via":"user"}}]},"ar15.carrier_cam_angle":{"label":"AR-15 bolt carrier, the cam track's turn","kind":"angle","measurements":[{"id":"tdp","value":22.5,"unit":"deg","pm":0.5,"stated":"22 1/2°","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 2 of 2, rev K, PDF page 203: the cam track's layout; user-supplied scan","via":"user"},"note":"Toward the carrier's left."}]},"ar15.carrier_cam_tail":{"label":"AR-15 bolt carrier, the cam track's straight run at 22 1/2° past its last coordinate","kind":"length","measurements":[{"id":"tdp","value":0.07,"unit":"in","pm":0.005,"stated":".070","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 2 of 2, rev K, PDF page 203: the cam track's layout; user-supplied scan","via":"user"}}]},"ar15.carrier_serration_count":{"label":"AR-15 bolt carrier, the forward assist's serrations","kind":"count","measurements":[{"id":"tdp","value":28,"unit":"count","pm":0,"stated":"(28) SERRATIONS","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the top view; user-supplied scan","via":"user"},"note":"On the right side, level with the axis."}]},"ar15.carrier_serration_pitch":{"label":"AR-15 bolt carrier, the serrations' pitch","kind":"length","measurements":[{"id":"tdp","value":0.125,"unit":"in","pm":0.003,"stated":".125 ±.003 PITCH","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the top view; user-supplied scan","via":"user"}}]},"ar15.carrier_serration_depth":{"label":"AR-15 bolt carrier, the serrations' depth","kind":"length","measurements":[{"id":"tdp","value":0.042,"unit":"in","pm":0.004,"stated":".042 ±.004","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: Section Y-Y; user-supplied scan","via":"user"}}]},"ar15.carrier_serration_cutter_r":{"label":"AR-15 bolt carrier, the radius the serrations are cut to","kind":"length","measurements":[{"id":"tdp","value":0.3125,"unit":"in","pm":0.0025,"stated":".3125 R ±.0025 ... 28 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: Section Y-Y; user-supplied scan","via":"user"},"note":"Each is cut across the side on this radius, which is why they show as lens shapes."}]},"ar15.carrier_serration_flank_angle":{"label":"AR-15 bolt carrier, the serrations' long flank, from the axis","kind":"angle","measurements":[{"id":"tdp","value":22.25,"unit":"deg","pm":0.5,"stated":"22°15' ±0°30'","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the top view; user-supplied scan","via":"user"}}]},"ar15.carrier_serration_face_angle":{"label":"AR-15 bolt carrier, the serrations' steep face, from the axis","kind":"angle","measurements":[{"id":"tdp","value":70.5,"unit":"deg","pm":0.5,"stated":"70°30' ±0°30'","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the top view; user-supplied scan","via":"user"},"note":"Taken as the face the pawl bears on, toward the rear of each notch."}]},"ar15.carrier_serration_front":{"label":"AR-15 bolt carrier, the foremost serration, from the front face","kind":"length","measurements":[{"id":"tdp","value":1.9,"unit":"in","pm":0.01,"stated":"1.90 (-T-)","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the top view; user-supplied scan","via":"user"},"note":"The dimension is to the rear of the flat's run-out, where the serrations begin .03 REF behind it; taken as the first serration's front edge."}]},"ar15.carrier_retaining_pin_x":{"label":"AR-15 bolt carrier, the firing pin retaining pin's hole, from the front face","kind":"length","measurements":[{"id":"tdp","value":2.536,"unit":"in","pm":0.008,"stated":"2.536 ±.008","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the side elevation; user-supplied scan","via":"user"}}]},"ar15.carrier_retaining_pin_y":{"label":"AR-15 bolt carrier, the firing pin retaining pin's hole, above the axis","kind":"length","measurements":[{"id":"tdp","value":0.157,"unit":"in","pm":0.008,"stated":".157 ±.008","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 2 of 2, rev K, PDF page 203: Section S-S; user-supplied scan","via":"user"}}]},"ar15.carrier_retaining_pin_csk_d":{"label":"AR-15 bolt carrier, the countersink for the retaining pin's head (left side)","kind":"length","measurements":[{"id":"tdp","value":0.281,"unit":"in","pm":0.005,"stated":".093 DIA +.005 THRU / .281 DIA X 82° CSK TO DEPTH SHOWN","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 2 of 2, rev K, PDF page 203: Section S-S; user-supplied scan","via":"user"}}]},"ar15.carrier_side_hole_x":{"label":"AR-15 bolt carrier, the hole in its right side behind the flat, from the front face","kind":"length","measurements":[{"id":"tdp","value":2.15,"unit":"in","pm":0.01,"stated":"2.15","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the side elevation; user-supplied scan","via":"user"},"note":"\".125 DIA THRU ONE SIDE\", level with the axis."}]},"ar15.carrier_side_hole_d":{"label":"AR-15 bolt carrier, the hole in its right side behind the flat, diameter","kind":"length","measurements":[{"id":"tdp","value":0.125,"unit":"in","pm":0.005,"stated":".125 DIA THRU ONE SIDE","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the side elevation; user-supplied scan","via":"user"}}]},"ar15.carrier_key_length":{"label":"AR-15 carrier key, length","kind":"length","measurements":[{"id":"tdp","value":2.465,"unit":"in","pm":0.005,"stated":"2.465","source":{"type":"standard","doc":"US Army TDP drawing 8448506 (Key, Bolt Carrier), rev J, PDF page 202: Section E-E; user-supplied scan","via":"user"}}]},"ar15.carrier_key_width":{"label":"AR-15 carrier key, its base's width","kind":"length","measurements":[{"id":"tdp","value":0.4005,"unit":"in","pm":0.001,"stated":".4005 ±.0010 (-B-)","source":{"type":"standard","doc":"US Army TDP drawing 8448506 (Key, Bolt Carrier), rev J, PDF page 202: the front view; user-supplied scan","via":"user"}}]},"ar15.carrier_key_base_height":{"label":"AR-15 carrier key, its base's height","kind":"length","measurements":[{"id":"tdp","value":0.241,"unit":"in","pm":0.006,"stated":".241 ±.006","source":{"type":"standard","doc":"US Army TDP drawing 8448506 (Key, Bolt Carrier), rev J, PDF page 202: the rear view; user-supplied scan","via":"user"}}]},"ar15.carrier_key_height":{"label":"AR-15 carrier key, height from its seat to the top of its tube","kind":"length","measurements":[{"id":"tdp","value":0.489,"unit":"in","pm":0.004,"stated":".489 ±.004","source":{"type":"standard","doc":"US Army TDP drawing 8448506 (Key, Bolt Carrier), rev J, PDF page 202: the rear view; user-supplied scan","via":"user"}}]},"ar15.carrier_key_step_height":{"label":"AR-15 carrier key, the step in its base's sides, above the seat","kind":"length","measurements":[{"id":"tdp","value":0.182,"unit":"in","pm":0.005,"stated":".182","source":{"type":"standard","doc":"US Army TDP drawing 8448506 (Key, Bolt Carrier), rev J, PDF page 202: the rear view; user-supplied scan","via":"user"},"note":"Above it the base is narrower by .030 a side (carrier_key_step)."}]},"ar15.carrier_key_step":{"label":"AR-15 carrier key, how much narrower its base is above the step, each side","kind":"length","measurements":[{"id":"tdp","value":0.03,"unit":"in","pm":0.005,"stated":".030 BOTH SIDES","source":{"type":"standard","doc":"US Army TDP drawing 8448506 (Key, Bolt Carrier), rev J, PDF page 202: the rear view; user-supplied scan","via":"user"}}]},"ar15.carrier_key_tube_d":{"label":"AR-15 carrier key, its tube's diameter","kind":"length","measurements":[{"id":"tdp","value":0.25,"unit":"in","pm":0.005,"stated":".250 DIA -.005 (-D-)","source":{"type":"standard","doc":"US Army TDP drawing 8448506 (Key, Bolt Carrier), rev J, PDF page 202: the plan view; user-supplied scan","via":"user"},"note":"The rib behind the tube is the same width with a full radius on top (\".250 BLEND WITH -D-\", \"FULL R\")."}]},"ar15.carrier_key_tube_axis_y":{"label":"AR-15 carrier key, its tube's axis above the seat","kind":"length","measurements":[{"id":"tdp","value":0.361,"unit":"in","pm":0.003,"stated":".361 ±.003","source":{"type":"standard","doc":"US Army TDP drawing 8448506 (Key, Bolt Carrier), rev J, PDF page 202: the front view; user-supplied scan","via":"user"}}]},"ar15.carrier_key_tube_length":{"label":"AR-15 carrier key, its tube's length","kind":"length","measurements":[{"id":"tdp","value":0.9,"unit":"in","pm":0.005,"stated":".900","source":{"type":"standard","doc":"US Army TDP drawing 8448506 (Key, Bolt Carrier), rev J, PDF page 202: the side view; user-supplied scan","via":"user"}}]},"ar15.carrier_key_ramp_top":{"label":"AR-15 carrier key, the top of its ramp, from its front end","kind":"length","measurements":[{"id":"tdp","value":1.26,"unit":"in","pm":0.01,"stated":"1.26","source":{"type":"standard","doc":"US Army TDP drawing 8448506 (Key, Bolt Carrier), rev J, PDF page 202: Section E-E; user-supplied scan","via":"user"},"note":"Behind it the top falls at 45° to the base."}]},"ar15.carrier_key_foot_length":{"label":"AR-15 carrier key, its seat's length from its rear end","kind":"length","measurements":[{"id":"tdp","value":1.31,"unit":"in","pm":0.01,"stated":"1.31","source":{"type":"standard","doc":"US Army TDP drawing 8448506 (Key, Bolt Carrier), rev J, PDF page 202: Section E-E; user-supplied scan","via":"user"},"note":"Ahead of it the underside rises at 45° to the tube."}]},"ar15.carrier_key_ramp_angle":{"label":"AR-15 carrier key, the angle of its ramps","kind":"angle","measurements":[{"id":"tdp","value":45,"unit":"deg","pm":0.5,"stated":"45°0' ±0°30'","source":{"type":"standard","doc":"US Army TDP drawing 8448506 (Key, Bolt Carrier), rev J, PDF page 202: Section E-E; user-supplied scan","via":"user"}}]},"ar15.carrier_key_screw_from_front":{"label":"AR-15 carrier key, its forward screw hole, from its front end","kind":"length","measurements":[{"id":"tdp","value":1.765,"unit":"in","pm":0.005,"stated":"1.765","source":{"type":"standard","doc":"US Army TDP drawing 8448506 (Key, Bolt Carrier), rev J, PDF page 202: the plan view; user-supplied scan","via":"user"},"note":"With the carrier's own 2.055 this puts the key's front end .290 behind the carrier's front face."}]},"ar15.carrier_key_cbore_d":{"label":"AR-15 carrier key, the counterbores for its screws' heads","kind":"length","measurements":[{"id":"tdp","value":0.273,"unit":"in","pm":0.007,"stated":".169 DIA +.005 THRU / .273 DIA +.007 C BORE TO DEPTH SHOWN","source":{"type":"standard","doc":"US Army TDP drawing 8448506 (Key, Bolt Carrier), rev J, PDF page 202: the plan view; user-supplied scan","via":"user"},"note":"Stated + .007 only. Their depth isn't dimensioned."}]},"ar15.carrier_key_bore_d":{"label":"AR-15 carrier key, its tube's bore","kind":"length","measurements":[{"id":"tdp","value":0.1805,"unit":"in","pm":0.0008,"stated":".1805 DIA +.0008 FULL DEPTH AFTER FINISH (-C-)","source":{"type":"standard","doc":"US Army TDP drawing 8448506 (Key, Bolt Carrier), rev J, PDF page 202: Section E-E; user-supplied scan","via":"user"},"note":"Stated + .0008 only."}]},"ar15.carrier_key_bore_depth":{"label":"AR-15 carrier key, its tube's bore, depth from the mouth","kind":"length","measurements":[{"id":"tdp","value":0.82,"unit":"in","pm":0.01,"stated":".82","source":{"type":"standard","doc":"US Army TDP drawing 8448506 (Key, Bolt Carrier), rev J, PDF page 202: Partial Section J-J; user-supplied scan","via":"user"}}]},"ar15.carrier_key_mouth_d":{"label":"AR-15 carrier key, the chamfer at its tube's mouth, diameter","kind":"length","measurements":[{"id":"tdp","value":0.225,"unit":"in","pm":0.005,"stated":"60° ±4° INCL TO .225 DIA","source":{"type":"standard","doc":"US Army TDP drawing 8448506 (Key, Bolt Carrier), rev J, PDF page 202: Partial Section J-J; user-supplied scan","via":"user"}}]},"ar15.carrier_key_screw_head_d":{"label":"AR-15 carrier key screw, head diameter","kind":"length","measurements":[{"id":"tdp","value":0.266,"unit":"in","pm":0.004,"stated":".266 ±.004","source":{"type":"standard","doc":"US Army TDP drawing 8448508 (Screw, Cap, Hex Socket Head), rev C, PDF page 49: the end view; user-supplied scan","via":"user"}}]},"ar15.carrier_key_screw_head_h":{"label":"AR-15 carrier key screw, head height","kind":"length","measurements":[{"id":"tdp","value":0.159,"unit":"in","pm":0.005,"stated":".159 +.005","source":{"type":"standard","doc":"US Army TDP drawing 8448508 (Screw, Cap, Hex Socket Head), rev C, PDF page 49: the side view; user-supplied scan","via":"user"},"note":"Stated + .005 only."}]},"ar15.carrier_key_screw_socket":{"label":"AR-15 carrier key screw, its socket across the flats","kind":"length","measurements":[{"id":"tdp","value":0.125,"unit":"in","pm":0.002,"stated":"SOCKET FOR 1/8 HEX WRENCH (.125 +.002 TYP)","source":{"type":"standard","doc":"US Army TDP drawing 8448508 (Screw, Cap, Hex Socket Head), rev C, PDF page 49: the end view; user-supplied scan","via":"user"}}]},"ar15.carrier_cam_pin_d":{"label":"AR-15 cam pin, shank diameter","kind":"length","measurements":[{"id":"tdp","value":0.3105,"unit":"in","pm":0.0005,"stated":".3105 DIA -.0005 GRIND AFTER HEAT TREAT (-B-)","source":{"type":"standard","doc":"US Army TDP drawing 8448502 (Pin, Cam), rev F, PDF page 210: the side view; user-supplied scan","via":"user"}}]},"ar15.carrier_cam_pin_head_width":{"label":"AR-15 cam pin, its head across the carrier","kind":"length","measurements":[{"id":"tdp","value":0.401,"unit":"in","pm":0.001,"stated":".401 ±.001","source":{"type":"standard","doc":"US Army TDP drawing 8448502 (Pin, Cam), rev F, PDF page 210: the end view; user-supplied scan","via":"user"},"note":"Taken as the head's size across the carrier: a seller's front photo of a carrier group shows the head about .41 wide under the key."}]},"ar15.carrier_cam_pin_head_length":{"label":"AR-15 cam pin, its head along the carrier","kind":"length","measurements":[{"id":"tdp","value":0.32,"unit":"in","pm":0.005,"stated":".320 -.005","source":{"type":"standard","doc":"US Army TDP drawing 8448502 (Pin, Cam), rev F, PDF page 210: the end view; user-supplied scan","via":"user"}}]},"ar15.carrier_cam_pin_head_height":{"label":"AR-15 cam pin, its head's thickness","kind":"length","measurements":[{"id":"tdp","value":0.095,"unit":"in","pm":0.005,"stated":".095","source":{"type":"standard","doc":"US Army TDP drawing 8448502 (Pin, Cam), rev F, PDF page 210: the side view; user-supplied scan","via":"user"}}]},"ar15.carrier_cam_pin_hole_to_head":{"label":"AR-15 cam pin, from the firing pin's hole through it to the underside of its head","kind":"length","measurements":[{"id":"tdp","value":0.507,"unit":"in","pm":0.002,"stated":".507 ±.002","source":{"type":"standard","doc":"US Army TDP drawing 8448502 (Pin, Cam), rev F, PDF page 210: the side view; user-supplied scan","via":"user"},"note":"The firing pin passes through it on the bolt's axis, so this is the head's underside above the axis."}]},"ar15.carrier_cam_pin_head_corner_d":{"label":"AR-15 cam pin, the diameter its head's ends are turned to","kind":"length","measurements":[{"id":"tdp","value":0.47,"unit":"in","pm":0.005,"stated":".470 DIA -.005, 2 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 8448502 (Pin, Cam), rev F, PDF page 210: the end view; user-supplied scan","via":"user"}}]},"ar15.carrier_retaining_pin_head":{"label":"AR-15 firing pin retaining pin, its eye's width","kind":"length","measurements":[{"id":"tdp","value":0.205,"unit":"in","pm":0.01,"stated":".205 ±.010","source":{"type":"standard","doc":"US Army TDP drawing 8448504 (Pin, Retaining, Firing Pin), rev F, PDF page 196: the side view; user-supplied scan","via":"user"}}]},"ar15.carrier_retaining_pin_wire":{"label":"AR-15 firing pin retaining pin, its wire","kind":"length","measurements":[{"id":"tdp","value":0.09,"unit":"in","pm":0.005,"stated":".090 DIA -.005","source":{"type":"standard","doc":"US Army TDP drawing 8448504 (Pin, Retaining, Firing Pin), rev F, PDF page 196: the side view; user-supplied scan","via":"user"}}]},"ar15.carrier_bolt_length":{"label":"AR-15 bolt, length","kind":"length","measurements":[{"id":"tdp","value":2.8,"unit":"in","pm":0.005,"stated":"2.800 REF","source":{"type":"standard","doc":"US Army drawing 8448510 (Bolt), sheet 1 of 2, rev E, in the user's reference set beside the TDP (Spec_Sheets/M16_Additional_Prints.pdf, page 4): the side view; user-supplied scan","via":"user"},"note":"The tail's end to the front of the lugs."}]},"ar15.carrier_bolt_face_from_rear":{"label":"AR-15 bolt, its face from its tail's end","kind":"length","measurements":[{"id":"tdp","value":2.675,"unit":"in","pm":0.002,"stated":"2.675 ±.002","source":{"type":"standard","doc":"US Army drawing 8448510 (Bolt), sheet 2 of 2, rev E, in the user's reference set beside the TDP (Spec_Sheets/M16_Additional_Prints.pdf, page 5): Section B-B; user-supplied scan","via":"user"},"note":"The recessed face the cartridge's head bears on; the lugs stand ahead of it."}]},"ar15.carrier_bolt_cam_hole_to_face":{"label":"AR-15 bolt, from the cam pin's hole to its face","kind":"length","measurements":[{"id":"tdp","value":1.305,"unit":"in","pm":0.004,"stated":"1.305 ±.004","source":{"type":"standard","doc":"US Army drawing 8448510 (Bolt), sheet 1 of 2, rev E, in the user's reference set beside the TDP (Spec_Sheets/M16_Additional_Prints.pdf, page 4): the top view; user-supplied scan","via":"user"},"note":"Taken as to the bolt's (recessed) face: on the sheet it ends .125 behind the lugs' front, where 2.800 REF less 2.675 puts the face."}]},"ar15.carrier_bolt_lug_od":{"label":"AR-15 bolt, across its lugs","kind":"length","measurements":[{"id":"tdp","value":0.743,"unit":"in","pm":0.005,"stated":".743 DIA -.005","source":{"type":"standard","doc":"US Army drawing 8448510 (Bolt), sheet 1 of 2, rev E, in the user's reference set beside the TDP (Spec_Sheets/M16_Additional_Prints.pdf, page 4): the end view; user-supplied scan","via":"user"}}]},"ar15.carrier_bolt_lug_root_d":{"label":"AR-15 bolt, the diameter at the lugs' roots","kind":"length","measurements":[{"id":"tdp","value":0.53,"unit":"in","pm":0.005,"stated":".530 DIA","source":{"type":"standard","doc":"US Army drawing 8448510 (Bolt), sheet 1 of 2, rev E, in the user's reference set beside the TDP (Spec_Sheets/M16_Additional_Prints.pdf, page 4): the end view; user-supplied scan","via":"user"}}]},"ar15.carrier_bolt_lug_length":{"label":"AR-15 bolt, its lugs' length","kind":"length","measurements":[{"id":"tdp","value":0.278,"unit":"in","pm":0.002,"stated":".278 ±.002","source":{"type":"standard","doc":"US Army drawing 8448510 (Bolt), sheet 1 of 2, rev E, in the user's reference set beside the TDP (Spec_Sheets/M16_Additional_Prints.pdf, page 4): the side view; user-supplied scan","via":"user"}}]},"ar15.carrier_bolt_lug_slot_width":{"label":"AR-15 bolt, the slots between its lugs, width","kind":"length","measurements":[{"id":"tdp","value":0.102,"unit":"in","pm":0.002,"stated":".102 ±.002, 6 PLACES (and .102 ±.001 about datum P, .051 DATUM)","source":{"type":"standard","doc":"US Army drawing 8448510 (Bolt), sheet 1 of 2, rev E, in the user's reference set beside the TDP (Spec_Sheets/M16_Additional_Prints.pdf, page 4): the end view; user-supplied scan","via":"user"},"note":"The slots between the lugs are what is dimensioned: parallel-sided, so each lug is wider at its tip than at its root. (A .168 ±.002 \"FOR HALF DEPTH\" callout on the same view was first taken for the lugs' width; it isn't identified and isn't used.) The user's reference CAD bolt has the same slots, .104 wide."}]},"ar15.carrier_bolt_lug_pitch":{"label":"AR-15 bolt, the angle between its lugs","kind":"angle","measurements":[{"id":"tdp","value":45,"unit":"deg","pm":0.5,"stated":"45° BASIC, 6 PLACES","source":{"type":"standard","doc":"US Army drawing 8448510 (Bolt), sheet 1 of 2, rev E, in the user's reference set beside the TDP (Spec_Sheets/M16_Additional_Prints.pdf, page 4): the end view; user-supplied scan","via":"user"},"note":"Eight places; the extractor has one."}]},"ar15.carrier_bolt_lug_offset":{"label":"AR-15 bolt, its lugs' pattern from the cam pin hole's centre line","kind":"angle","measurements":[{"id":"tdp","value":67.5,"unit":"deg","pm":0.5,"stated":"67°30' BASIC","source":{"type":"standard","doc":"US Army drawing 8448510 (Bolt), sheet 1 of 2, rev E, in the user's reference set beside the TDP (Spec_Sheets/M16_Additional_Prints.pdf, page 4): the end view; user-supplied scan","via":"user"},"note":"So the lugs stand 22°30' either side of the cam pin's line and every 45° from there."}]},"ar15.carrier_bolt_head_d":{"label":"AR-15 bolt, the diameter behind its lugs","kind":"length","measurements":[{"id":"tdp","value":0.55,"unit":"in","pm":0.005,"stated":".550 DIA -.005 (-U-)","source":{"type":"standard","doc":"US Army drawing 8448510 (Bolt), sheet 1 of 2, rev E, in the user's reference set beside the TDP (Spec_Sheets/M16_Additional_Prints.pdf, page 4): the side view; user-supplied scan","via":"user"}}]},"ar15.carrier_bolt_face_recess_d":{"label":"AR-15 bolt, the recess of its face, diameter","kind":"length","measurements":[{"id":"tdp","value":0.38,"unit":"in","pm":0.005,"stated":".380 DIA +.005","source":{"type":"standard","doc":"US Army drawing 8448510 (Bolt), sheet 2 of 2, rev E, in the user's reference set beside the TDP (Spec_Sheets/M16_Additional_Prints.pdf, page 5): Section B-B; user-supplied scan","via":"user"},"note":"The tolerance's last digits are faint on the copy."}]},"ar15.carrier_bolt_lug_chamfer":{"label":"AR-15 bolt, the chamfer on its lugs","kind":"length","measurements":[{"id":"tdp","value":0.01,"unit":"in","pm":0.005,"stated":".010 X 45° BASIC CHAMFER, 7 LUGS","source":{"type":"standard","doc":"US Army drawing 8448510 (Bolt), sheet 1 of 2, rev E, in the user's reference set beside the TDP (Spec_Sheets/M16_Additional_Prints.pdf, page 4): the side view; user-supplied scan","via":"user"}}]},"ar15.carrier_key_screw_socket_depth":{"label":"AR-15 carrier key screw, its socket's depth","kind":"length","measurements":[{"id":"tdp","value":0.077,"unit":"in","pm":0.005,"stated":".077 MIN","source":{"type":"standard","doc":"US Army TDP drawing 8448508 (Screw, Cap, Hex Socket Head), rev C, PDF page 49: the side view; user-supplied scan","via":"user"},"note":"A least depth; drawn at it."}]},"ar15.carrier_retaining_pin_hole_d":{"label":"AR-15 bolt carrier, the firing pin retaining pin's hole, diameter","kind":"length","measurements":[{"id":"tdp","value":0.093,"unit":"in","pm":0.005,"stated":".093 DIA +.005 THRU","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 2 of 2, rev K, PDF page 203: Section S-S; user-supplied scan","via":"user"},"note":"Stated + .005 only."}]},"ar15.carrier_retaining_pin_csk_angle":{"label":"AR-15 bolt carrier, the angle of the countersink for the retaining pin's head","kind":"angle","measurements":[{"id":"tdp","value":82,"unit":"deg","pm":1,"stated":".281 DIA X 82° CSK TO DEPTH SHOWN","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 2 of 2, rev K, PDF page 203: Section S-S; user-supplied scan","via":"user"},"note":"Included angle. Drawn from the carrier's surface inward, since its depth isn't dimensioned."}]},"ar15.carrier_vent_angle":{"label":"AR-15 bolt carrier, the upper vent hole above the horizontal","kind":"angle","measurements":[{"id":"tdp","value":45,"unit":"deg","pm":1,"stated":"45°","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the end view; user-supplied scan","via":"user"},"note":"The other vent is level with the axis."}]},"ar15.carrier_bolt_lugs":{"label":"AR-15 bolt, its lugs","kind":"count","measurements":[{"id":"tdp","value":7,"unit":"count","pm":0,"stated":".010 X 45° BASIC CHAMFER, 7 LUGS","source":{"type":"standard","doc":"US Army drawing 8448510 (Bolt), sheet 1 of 2, rev E, in the user's reference set beside the TDP (Spec_Sheets/M16_Additional_Prints.pdf, page 4): the side view; user-supplied scan","via":"user"},"note":"Seven of the eight places; the extractor's claw has the eighth."}]},"ar15.carrier_key_mouth_angle":{"label":"AR-15 carrier key, the angle of the chamfer at its tube's mouth","kind":"angle","measurements":[{"id":"tdp","value":60,"unit":"deg","pm":4,"stated":"60° ±4° INCL TO .225 DIA","source":{"type":"standard","doc":"US Army TDP drawing 8448506 (Key, Bolt Carrier), rev J, PDF page 202: Partial Section J-J; user-supplied scan","via":"user"},"note":"Included angle."}]},"ar15.carrier_front_chamfer_angle":{"label":"AR-15 bolt carrier, the angle of the chamfer at the front of the lower rails","kind":"angle","measurements":[{"id":"tdp","value":45,"unit":"deg","pm":2,"stated":"45° ±2°","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: the detail beside the end view; user-supplied scan","via":"user"}}]},"ar15.carrier_key_slot_ramp_angle":{"label":"AR-15 bolt carrier, the ramp from the key's slot down to the top cut","kind":"angle","measurements":[{"id":"tdp","value":45,"unit":"deg","pm":1,"stated":"45°","source":{"type":"standard","doc":"US Army TDP drawing 8448507 (Carrier, Bolt), sheet 1 of 2, rev K, PDF page 204: View Z (alternate method); user-supplied scan","via":"user"},"note":"The alternate method; not drawn (carrier_key_slot_rear)."}]},"ar15.carrier_bolt_body_d":{"label":"AR-15 bolt, its body's diameter (what runs in the carrier)","kind":"length","measurements":[{"id":"tdp","value":0.528,"unit":"in","pm":0.0005,"stated":".5280 DIA ±.0005 (-F-) GRIND AFTER HEAT TREAT","source":{"type":"standard","doc":"US Army drawing 8448510 (Bolt), sheet 1 of 2, rev E, in the user's reference set beside the TDP (Spec_Sheets/M16_Additional_Prints.pdf, page 4): the side view; user-supplied scan","via":"user"},"note":"It shows at the bottom of the carrier's cam track."}]},"nfa.rifle_barrel_min":{"label":"National Firearms Act: the barrel length under which a rifle is one of the Act's firearms","kind":"length","measurements":[{"id":"statute","value":16,"unit":"in","pm":0,"stated":"a rifle having a barrel or barrels of less than 16 inches in length","source":{"type":"standard","doc":"26 U.S.C. § 5845(a)(3), as Cornell's Legal Information Institute renders the United States Code (read 2026-10-04)","url":"https://www.law.cornell.edu/uscode/text/26/5845"}},{"id":"atf","value":16,"unit":"in","pm":0,"stated":"A rifle subject to the NFA has a barrel or barrels of less than 16 inches in length.","source":{"type":"standard","doc":"ATF, National Firearms Act Handbook, chapter 2, section 2.1.3 (its p. 6); saved from ATF's site by the user, 2026-10-06 (references/nfa)","url":"https://www.atf.gov/media/25146/download","via":"user"}}],"adopt":{"from":"statute","reason":"The Act's own words; ATF's handbook says the same."},"note":"A statute's figure: exact. How a barrel is measured for it is ATF's procedure, quoted where the rule is declared (data/platforms/ar15.yaml, `nfa`)."},"nfa.rifle_overall_min":{"label":"National Firearms Act: the overall length under which a weapon made from a rifle is one of the Act's firearms","kind":"length","measurements":[{"id":"statute","value":26,"unit":"in","pm":0,"stated":"a weapon made from a rifle if such weapon as modified has an overall length of less than 26 inches or a barrel or barrels of less than 16 inches in length","source":{"type":"standard","doc":"26 U.S.C. § 5845(a)(4), as Cornell's Legal Information Institute renders the United States Code (read 2026-10-04)","url":"https://www.law.cornell.edu/uscode/text/26/5845"}},{"id":"atf","value":26,"unit":"in","pm":0,"stated":"A weapon made from a rifle is a rifle type weapon that has an overall length of less than 26 inches or a barrel or barrels of less than 16 inches in length.","source":{"type":"standard","doc":"ATF, National Firearms Act Handbook, chapter 2, section 2.1.4 (its p. 7); saved from ATF's site by the user, 2026-10-06 (references/nfa)","url":"https://www.atf.gov/media/25146/download","via":"user"}}],"adopt":{"from":"statute","reason":"The Act's own words; ATF's handbook says the same."}},"ar15.barrel_nut_length":{"label":"AR-15 barrel nut (the rifle's, for a drop-in handguard), its length from its rear face to its front face","kind":"length","measurements":[{"id":"model","value":0.85,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part; its drawing, 8448553, isn't in the package)","method":"its planes and cylinders read from the STEP text (mm), its axis along x: rear face at 0, front face at 21.59 (.cache/batch15/bcm-gi-barrel-nut/scripts/faces.py, 2026-10-28)","via":"user"}}]},"ar15.barrel_nut_shoulder":{"label":"AR-15 barrel nut, its inner shoulder (where it bears on the barrel extension's flange), from its rear face","kind":"length","measurements":[{"id":"model","value":0.525,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"the plane across its axis where the counterbore (cylinder r 15.875 mm, from 11.05 mm) steps down to the bore (r 12.83 mm): 13.335 mm from the rear face (.cache/batch15/bcm-gi-barrel-nut/scripts/faces.py)","via":"user"}}],"note":"Behind it a counterbore 1.25 across (r 0.625) from 0.435, for the flange (1.170 across: std.ar15.barrel_extension_flange_thickness); ahead of it the barrel's bore (std.ar15.barrel_nut_bore_d)."},"ar15.barrel_nut_rear_x":{"label":"AR-15 barrel nut, its rear face, from the upper receiver's front face (+ toward the muzzle)","kind":"length","measurements":[{"id":"derived","value":-0.394,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{std.ar15.barrel_extension_flange_thickness} - {std.ar15.barrel_nut_shoulder}","via":"user"}}],"note":"The nut's shoulder on the extension's flange, the flange on the receiver's front face. A check: the model's thread flanks end 0.394 from its rear face (std.ar15.barrel_nut_thread_length), which is where this puts the receiver's front face; and its rear face is 0.051 ahead of the shoulder the receiver's thread begins at (std.ar15.upper_barrel_thread_length, .445 REF)."},"ar15.barrel_nut_body_od":{"label":"AR-15 barrel nut, its body's outside diameter (what the slip ring's lip slides on, behind the toothed flange)","kind":"length","measurements":[{"id":"model","value":1.367,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"cylinder r 17.36 mm from 0.38 to 2.95 mm and from 4.60 to 18.54 mm along the axis (.cache/batch15/bcm-gi-barrel-nut/scripts/faces.py)","via":"user"},"note":"The ring's lip is 1.380 across (std.ar15.slip_ring_lip_hole_d): 0.013 of clearance."}]},"ar15.barrel_nut_groove":{"label":"AR-15 barrel nut, the snap ring's groove: its rear wall from the nut's rear face","kind":"length","measurements":[{"id":"model","value":0.126,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"the groove's floor, cylinder r 16.93 mm, from 3.20 to 4.34 mm along the axis, with its walls' 0.25 mm rounds (.cache/batch15/bcm-gi-barrel-nut/scripts/faces.py)","via":"user"}}]},"ar15.barrel_nut_groove_width":{"label":"AR-15 barrel nut, the snap ring's groove, its width","kind":"length","measurements":[{"id":"model","value":0.045,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"as barrel_nut_groove: 3.20 to 4.34 mm","via":"user"},"note":"The model's snap ring is 0.050 thick (std.ar15.slip_ring_retainer_thickness): the two don't fit by 0.005, and the groove is drawn as the model has it."}]},"ar15.barrel_nut_groove_d":{"label":"AR-15 barrel nut, the snap ring's groove, its floor's diameter","kind":"length","measurements":[{"id":"model","value":1.333,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"cylinder r 16.93 mm (.cache/batch15/bcm-gi-barrel-nut/scripts/faces.py)","via":"user"}}]},"ar15.barrel_nut_flange_rear":{"label":"AR-15 barrel nut, its toothed flange's rear face, from the nut's rear face (where the slip ring's lip stops)","kind":"length","measurements":[{"id":"model","value":0.73,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"the flange from 18.54 to 21.59 mm along the axis: a cylinder r 19.81 mm from 19.30 to 20.83 mm between two 45° chamfers 0.76 mm long (cones), and its 20 notches through it (.cache/batch15/bcm-gi-barrel-nut/scripts/faces.py)","via":"user"},"note":"The assembly drawing's side view (8448711, rev E, PDF page 169, at 2/1) has the nut standing 0.246 behind the ring's rear face (read on a 400 dpi render scaled by the ring's .600: .cache/batch15/bcm-gi-barrel-nut/pages/assy-side.png); with the ring's lip at .420 to .480 (8448712) on this face it is 0.250."}]},"ar15.barrel_nut_flange_od":{"label":"AR-15 barrel nut, its toothed flange's outside diameter","kind":"length","measurements":[{"id":"model","value":1.56,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"cylinder r 19.812 mm (.cache/batch15/bcm-gi-barrel-nut/scripts/faces.py)","via":"user"}}]},"ar15.barrel_nut_flange_chamfer":{"label":"AR-15 barrel nut, the 45° chamfer on each edge of its toothed flange, its length along the axis","kind":"length","measurements":[{"id":"model","value":0.03,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"two cones of 45° half-angle from r 19.05 to 19.81 mm, 18.54 to 19.30 and 20.83 to 21.59 mm along the axis (.cache/batch15/bcm-gi-barrel-nut/scripts/faces.py)","via":"user"}}]},"ar15.barrel_nut_notches":{"label":"AR-15 barrel nut, the notches round its flange (for the wrench and the gas tube)","kind":"count","measurements":[{"id":"model","value":20,"unit":"count","pm":0,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"20 cylinders r 2.36 mm along the axis through the flange, their axes 19.82 mm from the nut's, 18° apart (.cache/batch15/bcm-gi-barrel-nut/scripts/faces.py)","via":"user"},"note":"The assembly drawing's end view (8448711) draws them all round, the gas tube in the one at the top: counted there 10 to a half turn, from the tube's notch to the one opposite it."}]},"ar15.barrel_nut_notch_d":{"label":"AR-15 barrel nut, each notch's diameter (a round-bottomed slot through the flange)","kind":"length","measurements":[{"id":"model","value":0.186,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"cylinders r 2.362 mm (.cache/batch15/bcm-gi-barrel-nut/scripts/faces.py)","via":"user"},"note":"The gas tube is 0.180 across and its axis 0.78 above the bore's (std.ar15.gas_tube_above_bore): in the notch, whose axis is at barrel_nut_notch_pcd / 2."}]},"ar15.barrel_nut_notch_pcd":{"label":"AR-15 barrel nut, the circle the notches' axes lie on, its diameter","kind":"length","measurements":[{"id":"model","value":1.561,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"the notches' axes at 19.825 mm from the nut's (.cache/batch15/bcm-gi-barrel-nut/scripts/faces.py)","via":"user"}}]},"ar15.barrel_nut_bore_d":{"label":"AR-15 barrel nut, the bore the barrel passes through, its diameter","kind":"length","measurements":[{"id":"model","value":1.01,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"cylinder r 12.827 mm from 13.34 to 16.51 mm along the axis (.cache/batch15/bcm-gi-barrel-nut/scripts/faces.py)","via":"user"}}]},"ar15.barrel_nut_counterbore_d":{"label":"AR-15 barrel nut, its two counterbores' diameter (the extension's flange behind its shoulder; a recess in its front face)","kind":"length","measurements":[{"id":"model","value":1.25,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"cylinders r 15.875 mm from 11.05 to 13.34 mm and from 18.03 to 20.83 mm along the axis, the front one opening on a 45° chamfer to the front face (.cache/batch15/bcm-gi-barrel-nut/scripts/faces.py)","via":"user"}}]},"ar15.barrel_nut_front_recess":{"label":"AR-15 barrel nut, the recess in its front face, its depth","kind":"length","measurements":[{"id":"model","value":0.2,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"its floor, a plane across the axis at 16.51 mm from r 12.83 to 14.35 mm, a round of r 1.52 mm up to the recess's wall (r 15.875 mm) at 18.03 mm, the wall on to a 45° chamfer from 20.83 mm, the front face at 21.59 mm (.cache/batch15/bcm-gi-barrel-nut/scripts/faces.py)","via":"user"}}]},"ar15.barrel_nut_thread_length":{"label":"AR-15 barrel nut, its internal thread (1¼-18 UNEF, the receiver's): from its rear face to where its flanks end","kind":"length","measurements":[{"id":"model","value":0.394,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"the rear face to the plane at 10.01 mm where its two helical flanks (B-spline faces, from 0.33 mm, inside the rear chamfer) stop, between the minor cylinder r 15.11 mm and r 15.80 mm, a 45° chamfer from r 16.13 mm at the rear face and a plane at 10.01 mm where the flanks stop (.cache/batch15/bcm-gi-barrel-nut/scripts/faces.py)","via":"user"}}],"note":"The thread is the receiver's (bcm-m4-upper.thread_major_d, thread_pitch: the Army's 12576280, 1.250-18 UNEF-2A): the nut's own is its mate, internal, and not on any drawing on file. Its flanks end at 0.394 from the nut's rear face, where the receiver's front face stands (std.ar15.barrel_nut_rear_x): a check of that seat from inside the model."},"ar15.barrel_nut_thread_minor_d":{"label":"AR-15 barrel nut, its internal thread's minor diameter (its crests)","kind":"length","measurements":[{"id":"model","value":1.19,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"cylinder r 15.113 mm (.cache/batch15/bcm-gi-barrel-nut/scripts/faces.py)","via":"user"},"note":"The receiver's minor diameter is 1.1803 max (bcm-m4-upper.thread_minor_d): the nut's crests stand 0.005 off its roots."}]},"ar15.barrel_nut_thread_major_d":{"label":"AR-15 barrel nut, its internal thread's major diameter (its roots)","kind":"length","measurements":[{"id":"model","value":1.244,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"cylinder r 15.80 mm about the axis over the thread's run (.cache/batch15/bcm-gi-barrel-nut/scripts/faces.py)","via":"user"},"note":"The receiver's crests: 1.2485 to 1.2398 after coating (bcm-m4-upper.thread_major_d, 1.244)."}]},"ar15.barrel_nut_rear_chamfer":{"label":"AR-15 barrel nut, the 45° chamfer on its rear face's outer edge, its length along the axis","kind":"length","measurements":[{"id":"model","value":0.015,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"a cone of 45° from r 16.98 to 17.36 mm over the first 0.38 mm (.cache/batch15/bcm-gi-barrel-nut/scripts/faces.py)","via":"user"}}]},"ar15.barrel_nut_thread_chamfer":{"label":"AR-15 barrel nut, the 45° chamfer into its thread at its rear face, its length along the axis","kind":"length","measurements":[{"id":"model","value":0.04,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"a cone of 45° from r 16.13 mm at the rear face to the thread's minor r 15.11 mm at 1.02 mm (.cache/batch15/bcm-gi-barrel-nut/scripts/faces.py)","via":"user"}}]},"ar15.barrel_nut_inner_chamfer":{"label":"AR-15 barrel nut, the 45° chamfers inside it (into its front recess, and from its thread up to the counterbore behind its shoulder), their length along the axis","kind":"length","measurements":[{"id":"model","value":0.03,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"two cones of 45°: r 15.875 to 16.64 mm from 20.83 to 21.59 mm (the front face), and r 15.11 to 15.875 mm from 10.29 to 11.05 mm (.cache/batch15/bcm-gi-barrel-nut/scripts/faces.py)","via":"user"}}]},"ar15.barrel_nut_recess_round":{"label":"AR-15 barrel nut, the round in the corner of its front recess's floor, radius","kind":"length","measurements":[{"id":"model","value":0.06,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Barrel_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"a torus of minor r 1.524 mm from 16.51 to 18.03 mm along the axis, r 14.35 to 15.875 mm (.cache/batch15/bcm-gi-barrel-nut/scripts/faces.py)","via":"user"}}]},"ar15.slip_ring_retainer_hole_d":{"label":"AR-15 slip ring's snap ring, the hole in each of its ends (for the pliers), diameter","kind":"length","measurements":[{"id":"model","value":0.1,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Handguard_Delta_Ring_Retainer.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"two cylinders r 1.27 mm (.cache/batch15/bcm-gi-barrel-nut/scripts/faces.py)","via":"user"}}]},"ar15.slip_ring_retainer_hole_apart":{"label":"AR-15 slip ring's snap ring, its two holes' centres apart (across its gap)","kind":"length","measurements":[{"id":"model","value":0.457,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Handguard_Delta_Ring_Retainer.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"the two holes' axes at z ±5.81 mm, 19.32 mm from the ring's axis (.cache/batch15/bcm-gi-barrel-nut/scripts/faces.py)","via":"user"}}]},"ar15.slip_ring_retainer_hole_pcd":{"label":"AR-15 slip ring's snap ring, the circle its two holes' centres lie on, diameter","kind":"length","measurements":[{"id":"model","value":1.521,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Handguard_Delta_Ring_Retainer.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"the holes' axes 19.32 mm from the ring's (x 18.43, z ±5.81 mm) (.cache/batch15/bcm-gi-barrel-nut/scripts/faces.py)","via":"user"}}]},"ar15.slip_ring_retainer_waist_d":{"label":"AR-15 slip ring's snap ring, its inside where it is narrowest (between its ends' lugs and its back), diameter","kind":"length","measurements":[{"id":"model","value":1.503,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Handguard_Delta_Ring_Retainer.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"its flat face's outline from the STEP text: the inside at r 19.09 mm at 73.4 degrees from the gap's middle, where its two arcs meet (.cache/batch15/bcm-gi-barrel-nut/scripts/faces.py)","via":"user"}}],"note":"Its inside is the 1.372 circle at its two ends (the lugs round the pliers' holes) and over its back, and between them it is cut away to this, on two arcs (r 14.72 mm about a point 4.61 mm off its axis toward that end, then r 18.90 mm about one 1.97 mm toward the gap): narrowest about 73 degrees from the gap. BCM's and Spike's photos show the ends wider than the ring beside them."},"ar15.slip_ring_retainer_lug_end":{"label":"AR-15 slip ring's snap ring, where each end's lug ends (its inside leaves the 1.372 circle), from the gap's middle","kind":"angle","measurements":[{"id":"model","value":42,"unit":"deg","pm":0.5,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Handguard_Delta_Ring_Retainer.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"its flat face's outline: the inside's vertex at (12.94, 11.67 mm), 42.0 degrees from the gap's middle (.cache/batch15/bcm-gi-barrel-nut/scripts/faces.py)","via":"user"}}]},"ar15.slip_ring_retainer_waist_at":{"label":"AR-15 slip ring's snap ring, where its inside is narrowest, from the gap's middle","kind":"angle","measurements":[{"id":"model","value":73.4,"unit":"deg","pm":0.5,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Handguard_Delta_Ring_Retainer.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"its flat face's outline: the vertex where its two inside arcs meet, at (5.44, 18.30 mm) (.cache/batch15/bcm-gi-barrel-nut/scripts/faces.py)","via":"user"}}]},"ar15.slip_ring_retainer_back_start":{"label":"AR-15 slip ring's snap ring, where its back begins (its inside back on the 1.372 circle), from the gap's middle","kind":"angle","measurements":[{"id":"model","value":127.6,"unit":"deg","pm":0.5,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Handguard_Delta_Ring_Retainer.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"its flat face's outline: the inside's vertex at (-10.64, 13.80 mm), 127.6 degrees from the gap's middle; from there round the back to the same on the other side, the 1.372 circle (.cache/batch15/bcm-gi-barrel-nut/scripts/faces.py)","via":"user"}}]},"ar15.barrel_nut_front_x":{"label":"AR-15 barrel nut, its front face, from the upper receiver's front face (+ toward the muzzle)","kind":"length","measurements":[{"id":"derived","value":0.456,"unit":"in","pm":0.011,"source":{"type":"derived","expr":"{std.ar15.barrel_nut_rear_x} + {std.ar15.barrel_nut_length}","via":"user"}}]},"ar15.slip_ring_od":{"label":"AR-15 slip ring (the delta ring), its largest outside diameter (its rear land)","kind":"length","measurements":[{"id":"tdp","value":2.1,"unit":"in","pm":0.005,"stated":"2.100 DIA","source":{"type":"standard","doc":"US Army TDP drawing 8448712 (Slip Ring, Hand Guard), rev G, PDF page 168: Section B-B (and View F, 2.100 DIA REF); user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"Title-block ± .005. The reference CAD set's ring has the same (r 26.67 mm)."}]},"ar15.slip_ring_front_od":{"label":"AR-15 slip ring, its smallest outside diameter (its front land, after six steps down from the rear's)","kind":"length","measurements":[{"id":"tdp","value":1.92,"unit":"in","pm":0.005,"stated":"1.920 DIA","source":{"type":"standard","doc":"US Army TDP drawing 8448712 (Slip Ring, Hand Guard), rev G, PDF page 168: View F (scale 10/1); user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"2.100 less six steps of .015 a side. The CAD set's: 1.922 (r 24.41 mm)."}]},"ar15.slip_ring_length":{"label":"AR-15 slip ring, its length along the bore","kind":"length","measurements":[{"id":"tdp","value":0.6,"unit":"in","pm":0.005,"stated":".600","source":{"type":"standard","doc":"US Army TDP drawing 8448712 (Slip Ring, Hand Guard), rev G, PDF page 168: Section B-B; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"The CAD set's: 0.600 (15.24 mm)."}]},"ar15.slip_ring_step":{"label":"AR-15 slip ring, each step down its outside (radial), from its rear land toward the front","kind":"length","measurements":[{"id":"tdp","value":0.015,"unit":"in","pm":0.003,"stated":".015 ±.003, 6 PLACES TOLERANCE NON-ACCUMULATIVE","source":{"type":"standard","doc":"US Army TDP drawing 8448712 (Slip Ring, Hand Guard), rev G, PDF page 168: View F (scale 10/1); user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"The steps lie on a cone of 10° (Section B-B: 10°0' ±0°30'), each sharp to .005 max R."}]},"ar15.slip_ring_steps":{"label":"AR-15 slip ring, the steps down its outside","kind":"count","measurements":[{"id":"tdp","value":6,"unit":"count","pm":0,"stated":".015 ±.003, 6 PLACES","source":{"type":"standard","doc":"US Army TDP drawing 8448712 (Slip Ring, Hand Guard), rev G, PDF page 168: View F (scale 10/1); user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"Seven lands. The CAD set's ring has the six steps."}]},"ar15.slip_ring_land":{"label":"AR-15 slip ring, each land between its steps, its length along the bore","kind":"length","measurements":[{"id":"tdp","value":0.086,"unit":"in","pm":0.005,"stated":".086, 7 PLACES TOLERANCE NON-ACCUMULATIVE","source":{"type":"standard","doc":"US Army TDP drawing 8448712 (Slip Ring, Hand Guard), rev G, PDF page 168: View F (scale 10/1); user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"Five of them make View F's .430 between the first step and the last; seven make the ring's .600 within .002."}]},"ar15.slip_ring_bore_d":{"label":"AR-15 slip ring, its rear bore (round the weld spring and the snap ring), diameter","kind":"length","measurements":[{"id":"tdp","value":1.75,"unit":"in","pm":0.005,"stated":"1.750 DIA -B-","source":{"type":"standard","doc":"US Army TDP drawing 8448712 (Slip Ring, Hand Guard), rev G, PDF page 168: Section B-B; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"The CAD set's is 1.730 (r 21.97 mm), the weld spring's outside (8448555: 1.730 DIA MAX)."}]},"ar15.slip_ring_bore_depth":{"label":"AR-15 slip ring, its rear bore's depth (from its rear face to its lip's rear face)","kind":"length","measurements":[{"id":"tdp","value":0.42,"unit":"in","pm":0.005,"stated":".420","source":{"type":"standard","doc":"US Army TDP drawing 8448712 (Slip Ring, Hand Guard), rev G, PDF page 168: Section B-B; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"The CAD set's: 0.425."}]},"ar15.slip_ring_skirt_length":{"label":"AR-15 slip ring, its front skirt (ahead of the lip: what a drop-in handguard's rear end goes into), length","kind":"length","measurements":[{"id":"tdp","value":0.12,"unit":"in","pm":0.005,"stated":".120","source":{"type":"standard","doc":"US Army TDP drawing 8448712 (Slip Ring, Hand Guard), rev G, PDF page 168: Section B-B; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"The lip between the bore and the skirt is then .600 - .420 - .120 = .060 thick; the CAD set's lip is 0.050 and its skirt 0.125."}]},"ar15.slip_ring_skirt_d":{"label":"AR-15 slip ring, its front skirt's inside diameter","kind":"length","measurements":[{"id":"tdp","value":1.75,"unit":"in","pm":0.005,"stated":"1.750 ±.005 DIA","source":{"type":"standard","doc":"US Army TDP drawing 8448712 (Slip Ring, Hand Guard), rev G, PDF page 168: Section B-B; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"The CAD set's: 1.770 (r 22.48 mm)."}]},"ar15.slip_ring_lip_hole_d":{"label":"AR-15 slip ring, the hole in its lip (on the barrel nut's body), diameter","kind":"length","measurements":[{"id":"tdp","value":1.38,"unit":"in","pm":0.005,"stated":"1.380 DIA -C-","source":{"type":"standard","doc":"US Army TDP drawing 8448712 (Slip Ring, Hand Guard), rev G, PDF page 168: the end view; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"The CAD set's: 1.382."}]},"ar15.slip_ring_notch_width":{"label":"AR-15 slip ring, the notch in its lip for the gas tube, its width","kind":"length","measurements":[{"id":"tdp","value":0.203,"unit":"in","pm":0.005,"stated":".203","source":{"type":"standard","doc":"US Army TDP drawing 8448712 (Slip Ring, Hand Guard), rev G, PDF page 168: the end view, with FULL R at its end; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"The CAD set's: 0.190 (r 2.41 mm)."}]},"ar15.slip_ring_notch_reach":{"label":"AR-15 slip ring, the gas tube's notch, from the ring's axis to the notch's round end","kind":"length","measurements":[{"id":"tdp","value":0.875,"unit":"in","pm":0.005,"stated":".875","source":{"type":"standard","doc":"US Army TDP drawing 8448712 (Slip Ring, Hand Guard), rev G, PDF page 168: the end view; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"The skirt's and the bore's radius: the notch cuts the lip through. The CAD set's reaches 0.885, its own skirt's radius."}]},"ar15.slip_ring_chamfer":{"label":"AR-15 slip ring, the 45° chamfer at both ends of its outside","kind":"length","measurements":[{"id":"tdp","value":0.02,"unit":"in","pm":0.005,"stated":".020 X 45° ±2°, CHAMFER, BOTH ENDS","source":{"type":"standard","doc":"US Army TDP drawing 8448712 (Slip Ring, Hand Guard), rev G, PDF page 168: View F; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"}}]},"ar15.slip_ring_front_x":{"label":"AR-15 slip ring, its lip's front face (where a drop-in handguard's rear end bears), from the upper receiver's front face (+ toward the muzzle)","kind":"length","measurements":[{"id":"derived","value":0.336,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{std.ar15.barrel_nut_rear_x} + {std.ar15.barrel_nut_flange_rear}","via":"user"}}],"note":"The ring forward on its spring, its lip against the nut's toothed flange (std.ar15.barrel_nut_flange_rear), as the assembly drawing draws it (8448711). A handguard holds it a little behind that, by as much as the spring is pressed by the handguard's length between this face and its cap, which no drawing on file gives. The ring's front end is then .120 ahead (std.ar15.slip_ring_skirt_length), at 0.456: flush with the nut's front face (std.ar15.barrel_nut_front_x), round the flange."},"ar15.slip_ring_rear_x":{"label":"AR-15 slip ring, its rear face, from the upper receiver's front face (+ toward the muzzle)","kind":"length","measurements":[{"id":"derived","value":-0.144,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{std.ar15.slip_ring_front_x} - {std.ar15.slip_ring_length} + {std.ar15.slip_ring_skirt_length}","via":"user"}}],"note":"Negative: the ring's rear bore reaches back over the nut, 0.144 behind the receiver's front face and 0.30 ahead of the receiver's shoulder."},"ar15.slip_ring_spring_od":{"label":"AR-15 slip ring's weld spring (four wave sections welded), outside diameter","kind":"length","measurements":[{"id":"tdp","value":1.73,"unit":"in","pm":0.005,"stated":"1.730 DIA MAX","source":{"type":"standard","doc":"US Army TDP drawing 8448555 (Spring Weld Assembly, Hand Guard Slip Ring), rev E, PDF page 167; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"A maximum; the section's drawing (8448556) says 1.730 MAX. DIA AFTER FORMING, from a 1.735 blank."}]},"ar15.slip_ring_spring_id":{"label":"AR-15 slip ring's weld spring, inside diameter","kind":"length","measurements":[{"id":"tdp","value":1.41,"unit":"in","pm":0.005,"stated":"1.410 DIA MIN","source":{"type":"standard","doc":"US Army TDP drawing 8448555 (Spring Weld Assembly, Hand Guard Slip Ring), rev E, PDF page 167; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"}}]},"ar15.slip_ring_spring_height":{"label":"AR-15 slip ring's weld spring, its free height","kind":"length","measurements":[{"id":"tdp","value":0.552,"unit":"in","pm":0.01,"stated":".552 REF","source":{"type":"standard","doc":"US Army TDP drawing 8448555 (Spring Weld Assembly, Hand Guard Slip Ring), rev E, PDF page 167: the side view; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"Note 2: \"SPOT WELDS MUST HOLD AFTER COMPRESSION TO .215 HEIGHT\". On the rifle it stands between the snap ring and the ring's lip (0.50 with the ring forward)."}]},"ar15.slip_ring_spring_gap":{"label":"AR-15 slip ring's weld spring, the gap in its sections (the gas tube passes it)","kind":"length","measurements":[{"id":"tdp","value":0.245,"unit":"in","pm":0.015,"stated":".245 ±.015","source":{"type":"standard","doc":"US Army TDP drawing 8448555 (Spring Weld Assembly, Hand Guard Slip Ring), rev E, PDF page 167; and 8448556 (Spring Section), rev G, PDF page 166; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"}}]},"ar15.slip_ring_spring_strip":{"label":"AR-15 slip ring's weld spring, its steel strip's thickness","kind":"length","measurements":[{"id":"tdp","value":0.02,"unit":"in","pm":0.001,"stated":"STEEL, ASTM A684, 1075 COLD ROLLED STRIP ANNEALED. MATERIAL THICKNESS .020 ±.001.","source":{"type":"standard","doc":"US Army TDP drawing 8448556 (Spring Section, Hand Guard Slip Ring), rev G, PDF page 166: note 1; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"}}]},"ar15.slip_ring_spring_wave":{"label":"AR-15 slip ring's weld spring, each section's wave height (crest over trough)","kind":"length","measurements":[{"id":"tdp","value":0.138,"unit":"in","pm":0.01,"stated":".138 REF","source":{"type":"standard","doc":"US Army TDP drawing 8448556 (Spring Section, Hand Guard Slip Ring), rev G, PDF page 166: the three edge views; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"},"note":"The section is bent at 60° intervals (60°0' TYP), crests and troughs in turn: three waves round, the gap in one. Four sections, welded crest to crest (8448555)."}]},"ar15.slip_ring_spring_sections":{"label":"AR-15 slip ring's weld spring, its sections","kind":"count","measurements":[{"id":"tdp","value":4,"unit":"count","pm":0,"stated":"4-SPRING SECTION, HAND GUARD SLIP RING-8448556","source":{"type":"standard","doc":"US Army TDP drawing 8448555 (Spring Weld Assembly, Hand Guard Slip Ring), rev E, PDF page 167; user-supplied scan (Distribution Statement F, Colt proprietary notice)","via":"user"}}]},"ar15.slip_ring_retainer_od":{"label":"AR-15 slip ring's snap ring (MS16626-3137), outside diameter","kind":"length","measurements":[{"id":"model","value":1.671,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Handguard_Delta_Ring_Retainer.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part; MS16626-3137 isn't in the package)","method":"cylinder r 21.22 mm (.cache/batch15/bcm-gi-barrel-nut/scripts/faces.py)","via":"user"}}]},"ar15.slip_ring_retainer_id":{"label":"AR-15 slip ring's snap ring, inside diameter (as it sits in the nut's groove)","kind":"length","measurements":[{"id":"model","value":1.372,"unit":"in","pm":0.005,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Handguard_Delta_Ring_Retainer.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"cylinder r 17.42 mm, its inner edge (.cache/batch15/bcm-gi-barrel-nut/scripts/faces.py)","via":"user"},"note":"Wider than the groove's floor (1.333) and the nut's body (1.367): the model's ring is drawn free, not sprung into its groove."}]},"ar15.slip_ring_retainer_thickness":{"label":"AR-15 slip ring's snap ring, its thickness","kind":"length","measurements":[{"id":"model","value":0.05,"unit":"in","pm":0.003,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Handguard_Delta_Ring_Retainer.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"its two planes 1.27 mm apart (.cache/batch15/bcm-gi-barrel-nut/scripts/faces.py)","via":"user"}}]},"ar15.slip_ring_retainer_gap":{"label":"AR-15 slip ring's snap ring, the gap between its ends","kind":"length","measurements":[{"id":"model","value":0.2,"unit":"in","pm":0.01,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Handguard_Delta_Ring_Retainer.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part)","method":"its two end planes at z +2.48 and -2.60 mm, 0.200 in apart, each with an ear holding a hole r 1.27 mm for the pliers (.cache/batch15/bcm-gi-barrel-nut/scripts/faces.py)","via":"user"}}]}}},{"subject":"streamlight-protac-rail-mount-hl-x","title":"Streamlight ProTac Rail Mount HL-X (88066, 88071)","dimensions":{"weight":{"label":"Weight with two CR123A cells (item 88066), the rail clamp on","kind":"mass","measurements":[{"id":"fact-sheet","value":6.4,"unit":"oz","pm":0.05,"stated":"WEIGHT: 6.4 oz (181.4 g) with CR123A batteries","source":{"type":"spec","publisher":"manufacturer","name":"Streamlight, Product Fact Sheet: ProTac Rail Mount HL-X // ProTac Rail Mount HL-X USB (Document #297, Rev 4, revised 09/18/2023)","url":"https://www.streamlight.com/docs/default-source/fact-sheet/297.pdf","retrieved":"2026-10-05","via":"harvest"}},{"id":"info-sheet","value":6.4,"unit":"oz","pm":0.05,"stated":"WEIGHT: CR123A 6.4 oz (181.4g) // SL-B26 6.9 oz (195.6g)","source":{"type":"spec","publisher":"manufacturer","name":"Streamlight, ProTac Rail Mount HL-X info sheet with part numbers (6/25), Dimensions","url":"https://www.streamlight.com/docs/default-source/info-sheet-with-part-numbers/protacrailmounthl-x_sup.pdf","retrieved":"2026-10-05","via":"harvest"}},{"id":"page","value":6.4,"unit":"oz","pm":0.05,"stated":"Weight (Min) 6.40 ounces (181.44 grams)","source":{"type":"spec","publisher":"manufacturer","name":"Streamlight, ProTac Rail Mount HL-X (PROTAC RAIL MOUNT HL-X LONG GUN LIGHT), Product Specifications","url":"https://www.streamlight.com/products/detail/protac-rail-mount-hl-x","retrieved":"2026-10-05","via":"harvest"},"note":"The page names no battery beside its two weights; its two decimals are the fact sheet's 6.4 oz in grams (181.44) and back."},{"id":"data-sheet","value":6.4,"unit":"oz","pm":0.05,"stated":"5.43” (13.8 cm); 6.4 oz. (181.4g) with CR123A batteries; 6.9 oz. (195.6g) with Streamlight SL-B26® battery pack","source":{"type":"spec","publisher":"manufacturer","name":"Streamlight, ProTac Rail Mount HL-X USB // ProTac Rail Mount HL-X data sheet (11/23)","url":"https://www.streamlight.com/docs/default-source/data-sheet/protacrailmounthlx_datasheet.pdf?sfvrsn=cad1a7f0_87","retrieved":"2026-10-05","via":"harvest"}},{"id":"primary-arms","value":6.4,"unit":"oz","pm":0.05,"stated":"Weight 6.4 Oz","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Streamlight ProTac Rail Mount HL-X 1000 Lumen Weapon Light with Tapeswitch (SKU 88066), specifications","url":"https://www.primaryarms.com/streamlight-protac-rail-mount-hl-x-1000-lumen-weapon-light-tapeswitch","retrieved":"2026-10-05","via":"harvest"}},{"id":"midwayusa","value":6.4,"unit":"oz","pm":0.05,"stated":"Weight = 6.4 Ounce","source":{"type":"spec","publisher":"retailer","name":"MidwayUSA, Streamlight ProTac Rail Mount HL-X Weapon Light for Picatinny Rail Black (88066), the page's attribute table","url":"https://www.midwayusa.com/product/1018571930/","retrieved":"2026-10-05","via":"harvest"}},{"id":"ar15discounts","value":6.4,"unit":"oz","pm":0.05,"stated":"Weight 6.4 oz","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, Streamlight ProTac Railmount HL-X Weapon Light, 1000 Lumen, Black - 88066, Additional information","url":"https://ar15discounts.com/products/streamlight-protac-railmount-hl-x-weapon-light-1000-lumen-black/","retrieved":"2026-10-05","via":"harvest"}},{"id":"armamat","value":0.181,"unit":"kg","pm":0.0005,"stated":"Weight: 0.181 kg","source":{"type":"spec","publisher":"retailer","name":"armamat.ch (a Swiss shop), ProTac Rail Mount HL X, manufacturer number 88066, Dimensions & weight","url":"https://www.armamat.ch/en-ch/p/protac-rail-mount-hl-x-109949/","retrieved":"2026-10-05","via":"harvest"}},{"id":"rifle-supply","value":5.7,"unit":"oz","pm":0.05,"stated":"Overall Length 5.43\" Overall Weight 5.7oz","source":{"type":"spec","publisher":"retailer","name":"Rifle Supply, Streamlight ProTac HL-X Rail Mount | Remote Pressure Switch | 88066 (a listing with the light's earlier beam figures)","url":"https://riflesupply.com/Streamlight-ProTac-HL-X-Rail-Mount-Remote-Pressure-Switch-88066_p_1975.html","retrieved":"2026-10-05","via":"harvest"},"note":"0.7 oz under the maker's figure. The page carries the earlier output figures and a package line (\"nylon holster\") that isn't this light's, so the figure may be an earlier revision's or another ProTac's; no maker's document on file gives it."},{"id":"sportsmans","value":6.9,"unit":"oz","pm":0.05,"stated":"Weight 6.9oz","source":{"type":"spec","publisher":"retailer","name":"Sportsman's Warehouse, Streamlight ProTac Rail Mount HL-X Weapon Light (ID 1470378, MPN 88066), Specifications","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/gun-parts-accessories/gun-parts-magazines/weapon-lights/streamlight-protac-rail-mount-hl-x-gun-light/p/1470378","retrieved":"2026-10-05","via":"harvest"},"note":"The maker's figure with the SL-B26 pack, on the page for the package that ships with CR123A cells (its Battery Type row says CR123A Lithium)."}],"adopt":{"from":"fact-sheet","reason":"The maker's sheet, which names the batteries the figure is with; its page, info sheet and data sheet say the same, and three sellers repeat it. Rifle Supply's 5.7 oz and Sportsman's 6.9 oz are sellers' figures the maker's documents don't give for this package."},"note":"The fact sheet ties 6.4 oz to the CR123A cells; the page gives the same figure as its Weight (Min). Whether the tail switch or the remote switch is on, and that the rail clamp is (the photographs beside the figures show it on), no document says. A seller's older listing carries 5.7 oz, and one seller prints the rechargeable pack's 6.9 oz against this item: both kept."},"weight_sl_b26":{"label":"Weight with the SL-B26 rechargeable pack (item 88071), the rail clamp on","kind":"mass","measurements":[{"id":"fact-sheet","value":6.9,"unit":"oz","pm":0.05,"stated":"6.9 oz (195.6 g) with SL-B26 rechargeable battery pack","source":{"type":"spec","publisher":"manufacturer","name":"Streamlight, Product Fact Sheet: ProTac Rail Mount HL-X // ProTac Rail Mount HL-X USB (Document #297, Rev 4, revised 09/18/2023)","url":"https://www.streamlight.com/docs/default-source/fact-sheet/297.pdf","retrieved":"2026-10-05","via":"harvest"}},{"id":"info-sheet","value":6.9,"unit":"oz","pm":0.05,"stated":"WEIGHT: CR123A 6.4 oz (181.4g) // SL-B26 6.9 oz (195.6g)","source":{"type":"spec","publisher":"manufacturer","name":"Streamlight, ProTac Rail Mount HL-X info sheet with part numbers (6/25), Dimensions","url":"https://www.streamlight.com/docs/default-source/info-sheet-with-part-numbers/protacrailmounthl-x_sup.pdf","retrieved":"2026-10-05","via":"harvest"}},{"id":"page","value":6.9,"unit":"oz","pm":0.05,"stated":"Weight (Max) 6.90 ounces (195.61 grams)","source":{"type":"spec","publisher":"manufacturer","name":"Streamlight, ProTac Rail Mount HL-X (PROTAC RAIL MOUNT HL-X LONG GUN LIGHT), Product Specifications","url":"https://www.streamlight.com/products/detail/protac-rail-mount-hl-x","retrieved":"2026-10-05","via":"harvest"}},{"id":"sportsmans","value":6.9,"unit":"oz","pm":0.05,"stated":"Weight 6.9oz","source":{"type":"spec","publisher":"retailer","name":"Sportsman's Warehouse, Streamlight Protac Rail Mount HL-X Long Gun Light - Black (ID 1821926, MPN 88071), Specifications","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/gun-parts-accessories/gun-parts-magazines/weapon-lights/streamlight-protac-rail-mount-hl-x-long-gun-light-black/p/1821926","retrieved":"2026-10-05","via":"harvest"}},{"id":"midwayusa","value":6.4,"unit":"oz","pm":0.05,"stated":"Weight = 6.4 Ounce","source":{"type":"spec","publisher":"retailer","name":"MidwayUSA, Streamlight ProTac Rail Mount HL-X Rechargeable Weapon Light for Picatinny Rail Black (88071), the page's attribute table","url":"https://www.midwayusa.com/product/102958235","retrieved":"2026-10-05","via":"harvest"},"note":"The CR123A figure on the rechargeable package's page (its Battery Type row says SL-B26)."}],"adopt":{"from":"fact-sheet","reason":"The maker's sheet names the battery; its page and info sheet agree. MidwayUSA's 6.4 Ounce is the other package's figure."},"note":"The USB package's weight: the same light with one SL-B26 pack in place of two CR123A cells."},"length":{"label":"Overall length","kind":"length","measurements":[{"id":"page","value":5.43,"unit":"in","pm":0.005,"stated":"Length (Max) 5.43 inches (13.79 centimeters)","source":{"type":"spec","publisher":"manufacturer","name":"Streamlight, ProTac Rail Mount HL-X (PROTAC RAIL MOUNT HL-X LONG GUN LIGHT), Product Specifications","url":"https://www.streamlight.com/products/detail/protac-rail-mount-hl-x","retrieved":"2026-10-05","via":"harvest"}},{"id":"fact-sheet","value":5.43,"unit":"in","pm":0.005,"stated":"DIMENSIONS: Length: 5.43 in (13.8 cm)","source":{"type":"spec","publisher":"manufacturer","name":"Streamlight, Product Fact Sheet: ProTac Rail Mount HL-X // ProTac Rail Mount HL-X USB (Document #297, Rev 4, revised 09/18/2023)","url":"https://www.streamlight.com/docs/default-source/fact-sheet/297.pdf","retrieved":"2026-10-05","via":"harvest"}},{"id":"info-sheet","value":5.43,"unit":"in","pm":0.005,"stated":"LENGTH: 5.43 in (13.79 cm)","source":{"type":"spec","publisher":"manufacturer","name":"Streamlight, ProTac Rail Mount HL-X info sheet with part numbers (6/25), Dimensions","url":"https://www.streamlight.com/docs/default-source/info-sheet-with-part-numbers/protacrailmounthl-x_sup.pdf","retrieved":"2026-10-05","via":"harvest"}},{"id":"midwayusa","value":5.43,"unit":"in","pm":0.005,"stated":"Length = 5.43 Inches","source":{"type":"spec","publisher":"retailer","name":"MidwayUSA, Streamlight ProTac Rail Mount HL-X Weapon Light for Picatinny Rail Black (88066), the page's attribute table","url":"https://www.midwayusa.com/product/1018571930/","retrieved":"2026-10-05","via":"harvest"}},{"id":"rifle-supply","value":5.43,"unit":"in","pm":0.005,"stated":"Overall Length 5.43\"","source":{"type":"spec","publisher":"retailer","name":"Rifle Supply, Streamlight ProTac HL-X Rail Mount | Remote Pressure Switch | 88066 (a listing with the light's earlier beam figures)","url":"https://riflesupply.com/Streamlight-ProTac-HL-X-Rail-Mount-Remote-Pressure-Switch-88066_p_1975.html","retrieved":"2026-10-05","via":"harvest"}},{"id":"armamat","value":13.7,"unit":"cm","pm":0.1,"stated":"Length: 13.7 cm","source":{"type":"spec","publisher":"retailer","name":"armamat.ch (a Swiss shop), ProTac Rail Mount HL X, manufacturer number 88066, Dimensions & weight","url":"https://www.armamat.ch/en-ch/p/protac-rail-mount-hl-x-109949/","retrieved":"2026-10-05","via":"harvest"},"note":"One decimal, and 0.09 cm under the maker's 13.79: read as that figure cut short, so its ± is a whole last digit."},{"id":"gritr-infographic","value":5.45,"unit":"in","pm":0.005,"stated":"5.45 IN","source":{"type":"spec","publisher":"retailer","name":"GRITR Outdoors, STREAMLIGHT ProTac Rail Mount HL-X USB 1000 Lumens Long Gun Light (88071): the sixth gallery image, an infographic in the maker's style (references raw 56d3daf98da7)","url":"https://gritroutdoors.com/streamlight-protac-rail-mount-hl-x-usb-long-gun-light-88071","retrieved":"2026-10-05","via":"harvest"},"note":"A bracket under a picture of the light, end to end. The same graphic for the HL-X Pro on Streamlight's own page (references raw b587f45305d7) prints 5.43 IN."}],"adopt":{"from":"page","reason":"The maker's page, fact sheet and info sheet all print 5.43; the infographic's 5.45 stands alone against them."},"note":"The scale of every photograph here. An infographic in the maker's style on a seller's page prints 5.45 IN where the maker's documents all say 5.43 (the same graphic for the HL-X Pro, on Streamlight's own page, prints 5.43 IN); a Swiss shop's 13.7 cm is the maker's 13.79 cut short."},"listed_width":{"label":"The fact sheet's \"Width\" (what it spans isn't said)","kind":"length","measurements":[{"id":"fact-sheet","value":1.45,"unit":"in","pm":0.005,"stated":"Width: 1.45 in (3.68 cm)","source":{"type":"spec","publisher":"manufacturer","name":"Streamlight, Product Fact Sheet: ProTac Rail Mount HL-X // ProTac Rail Mount HL-X USB (Document #297, Rev 4, revised 09/18/2023)","url":"https://www.streamlight.com/docs/default-source/fact-sheet/297.pdf","retrieved":"2026-10-05","via":"harvest"}},{"id":"gritr-infographic","value":1.45,"unit":"in","pm":0.005,"stated":"1.45 IN","source":{"type":"spec","publisher":"retailer","name":"GRITR Outdoors, STREAMLIGHT ProTac Rail Mount HL-X USB 1000 Lumens Long Gun Light (88071): the sixth gallery image, an infographic in the maker's style (references raw 56d3daf98da7)","url":"https://gritroutdoors.com/streamlight-protac-rail-mount-hl-x-usb-long-gun-light-88071","retrieved":"2026-10-05","via":"harvest"}},{"id":"armamat","value":3.3,"unit":"cm","pm":0.05,"stated":"Width: 3.3 cm","source":{"type":"spec","publisher":"retailer","name":"armamat.ch (a Swiss shop), ProTac Rail Mount HL X, manufacturer number 88066, Dimensions & weight","url":"https://www.armamat.ch/en-ch/p/protac-rail-mount-hl-x-109949/","retrieved":"2026-10-05","via":"harvest"}}],"adopt":{"from":"fact-sheet","reason":"The maker's own sheet; the shop's 3.3 cm is its own, unsourced."},"note":"Not tied to a feature by any document. The infographic in the maker's style (GRITR's gallery; the HL-X Pro's on Streamlight's own page is the same) draws its 1.45 IN bracket across the head, beside the picture, the thumb wheel left out. The head's largest diameter reads 0.03 in less in the photographs scaled by the published length (head_diameter), so the figure isn't used for scale. A Swiss shop's 3.3 cm for both its width and its height (1.30 in) matches nothing measured here."},"listed_height":{"label":"The fact sheet's \"Height\" (what it spans isn't said)","kind":"length","measurements":[{"id":"fact-sheet","value":1.72,"unit":"in","pm":0.005,"stated":"Height: 1.72 in (4.37 cm)","source":{"type":"spec","publisher":"manufacturer","name":"Streamlight, Product Fact Sheet: ProTac Rail Mount HL-X // ProTac Rail Mount HL-X USB (Document #297, Rev 4, revised 09/18/2023)","url":"https://www.streamlight.com/docs/default-source/fact-sheet/297.pdf","retrieved":"2026-10-05","via":"harvest"}},{"id":"gritr-infographic","value":1.72,"unit":"in","pm":0.005,"stated":"1.72 IN","source":{"type":"spec","publisher":"retailer","name":"GRITR Outdoors, STREAMLIGHT ProTac Rail Mount HL-X USB 1000 Lumens Long Gun Light (88071): the sixth gallery image, an infographic in the maker's style (references raw 56d3daf98da7)","url":"https://gritroutdoors.com/streamlight-protac-rail-mount-hl-x-usb-long-gun-light-88071","retrieved":"2026-10-05","via":"harvest"}},{"id":"armamat","value":3.3,"unit":"cm","pm":0.05,"stated":"Height: 3.3 cm","source":{"type":"spec","publisher":"retailer","name":"armamat.ch (a Swiss shop), ProTac Rail Mount HL X, manufacturer number 88066, Dimensions & weight","url":"https://www.armamat.ch/en-ch/p/protac-rail-mount-hl-x-109949/","retrieved":"2026-10-05","via":"harvest"}}],"adopt":{"from":"fact-sheet","reason":"The maker's own sheet; the shop's 3.3 cm is its own, unsourced."},"note":"Not tied to a feature by any document. It is what the light measures across its head and out to the end of the clamp's thumb wheel (width): 1.74 in in Primary Arms' photo and 1.70 in the maker's, the wheel screwed further in. The infographic marks its 1.72 IN as a depth, into the picture."},"head_diameter":{"label":"Head diameter (across the cooling fins, its largest)","kind":"length","measurements":[{"id":"photo","value":1.424,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 96bbc99c1b2a (Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720)","scaleRef":"the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000 (.cache/batch123/streamlight-protac-rail-mount-hl-x/cam_fit.py)","method":"the four fins' tops to their mirror below the axis: 494.4 to 495.0 px at columns 343, 377, 440 and 479; the +/- is the scale's (0.4%) and two pixels","via":"harvest"}}],"note":"No document gives it by name. The fact sheet's Width, 1.45 in, is drawn across the head in the infographic (listed_width): 0.03 in more than this. The maker's own side-on photo of a 2016 unit (a61f009b2170) reads 1.418 by its length with no allowance for perspective, and the maker's photo of the light on an M-LOK handguard, scaled by the handguard's slots (83f4380a7ffe: 61.2 px to the 40 mm pitch), 1.41 +/- 0.03. The bezel ahead of the fins is 1.365."},"body_diameter":{"label":"Body diameter (the battery tube)","kind":"length","measurements":[{"id":"photo","value":0.92,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 96bbc99c1b2a (Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720)","scaleRef":"the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000 (.cache/batch123/streamlight-protac-rail-mount-hl-x/cam_fit.py)","method":"the tube's width, 319.4 px over columns 862 to 926 and 319.7 px over 1384 to 1544 (the same at both ends: the photo isn't yawed)","via":"harvest"}},{"id":"maker-photo","value":0.917,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x a61f009b2170 (Streamlight's gallery image _3: the same view of another unit, S/N 1116 010011, 800 x 800)","scaleRef":"the published length (.length) as the silhouette tip to tip, 783 px, with nothing taken off for perspective (its end sections read 2% shorter against its tube than Primary Arms': a longer lens)","method":"the tube's width, 132.4 px over columns 322 to 350 and 545 to 600","via":"harvest"}}],"adopt":{"from":"photo","reason":"The photo the outlines are traced from, at two and a half times the resolution, with its perspective taken off; the maker's own photo of another unit agrees within 0.4%."},"note":"The plain tube either side of the clamp. The two bands the clamp's legs hang from are 0.933, the neck ring behind the head 1.048, the tail cap's knurled grip 1.014."},"axis_above_mount":{"label":"The body's axis above the rail's top (on its rail clamp)","kind":"length","measurements":[{"id":"bolt","value":0.773,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{.bolt_below_axis} - ({std.picatinny.slot_depth} - {.stud_diameter} / 2)","via":"harvest"}},{"id":"mlok-photo","value":0.73,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 83f4380a7ffe (Streamlight's gallery image _5: a handguard from its right side, the light on its M-LOK mount, 800 x 800)","scaleRef":"the handguard's M-LOK slots: 61.2 px to the 40 mm pitch (std.mlok.slot_pitch), 38.9 px/in","method":"the body's axis (row 274.5: the tube's edges at 257 and 292) to the legs' lower ends at the mount's top edge (row 303), 28.5 px; one pixel is 0.026 in. The legs' feet taken as what sits on a rail's top","via":"harvest"}}],"adopt":{"from":"bolt","reason":"The clamp's own bolt, placed by the standard's slot; the M-LOK photo is 39 px to the inch and agrees within both +/-."},"note":"On the Picatinny clamp. Not published and in no straight view: the clamp's cross bolt is 0.81 below the axis (bolt_below_axis), and the bolt lies in a slot of the rail, here taken as resting on the slot's floor (it can sit no lower; riding higher would put the light up to 0.03 in nearer the rail). The same figure is the light's axis above the M-LOK mount's floor, where its legs stand. The mlok-photo row was read (batch 3) as the legs' feet at the mount's top edge in the maker's side view; the mount is known since 2026-10-19 to hold the legs on a floor leaning up from the plate's top edge (mlok_seat_angle), so what that row measures is the axis above the plate's top edge, which the mount's figures put at 0.80: the check is mlok_axis_above_screws."},"bolt_below_axis":{"label":"The clamp's cross bolt (the thumb wheel's stud) below the body's axis","kind":"length","measurements":[{"id":"oblique","value":0.807,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 0c0f9c6bb6f9 (Primary Arms 88066_01.jpg: the same unit from behind and above, thumb wheel toward the lens, 2200 x 1467)","scaleRef":"a camera fitted to the body's silhouette (the plan view's radii along the axis; focal length 8000 px, the lens 19.3 in off, rms 1.3 px away from the clamp and the ends)","method":"the stud's end face is a circle about the clamp's cross axis: its hex socket's ellipse (centre 1302.6, 1123.0; short axis at 24.2 degrees) gives the light's turn about its own axis and puts the stud's axis 0.807 below the body's, at the clamp's middle (.cache/batch123/streamlight-protac-rail-mount-hl-x/roll.py). The +/- covers two pixels on the ellipse and the fit","via":"harvest"}},{"id":"kit","value":0.86,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 5e8b2b975914 (GRITR's copy of the maker's kit picture for 88071: the light from its left side and from about 30 degrees above, the clamp's fixed jaw toward the lens, 1601 x 1601; engraved S/N 358732 0522)","scaleRef":"the tube's width there, 141.5 px, as .body_diameter: 153.8 px/in","method":"the bolt head's centre on the fixed jaw's face reads 1.01 in below the axis in the picture (155 px); the face stands 0.55 in nearer the lens, and for a view from 20 to 45 degrees above the side that puts the bolt 0.85 to 0.88 below the axis","via":"harvest"}}],"adopt":{"from":"oblique","reason":"A fitted camera on a 2200 px photo; the kit picture's angle is known only from where the engraving shows, and its reading agrees within both +/-."}},"stud_diameter":{"label":"The cross bolt's (stud's) diameter","kind":"length","measurements":[{"id":"photo","value":0.167,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 96bbc99c1b2a (Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720)","scaleRef":"the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000 (.cache/batch123/streamlight-protac-rail-mount-hl-x/cam_fit.py)","method":"the stud's end where it stands out of the thumb wheel: columns 1114 to 1171 at row 430, 58 px","via":"harvest"}}]},"width":{"label":"Overall width, across the head and out to the thumb wheel's end (as photographed)","kind":"length","measurements":[{"id":"photo","value":1.766,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 96bbc99c1b2a (Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720)","scaleRef":"the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000 (.cache/batch123/streamlight-protac-rail-mount-hl-x/cam_fit.py)","method":"the stud's end (row 426.1) to the head's far side (row 1039.5): 613.4 px","via":"harvest"}}],"note":"With the rail clamp on. The wheel screws in as the clamp closes: the maker's own photo (a61f009b2170) reads 1.71 in. The fact sheet's Height, 1.72 in, sits between the two (listed_height)."},"front_x":{"label":"The bezel's front ahead of the clamp's middle","kind":"length","measurements":[{"id":"photo","value":2.946,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 96bbc99c1b2a (Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720)","scaleRef":"the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000 (.cache/batch123/streamlight-protac-rail-mount-hl-x/cam_fit.py)","method":"the clamp's middle is the thumb wheel's centre (column 1142.0: the wheel spans 1034 to 1250); the bezel's tip shows at column 87.8, 30.9 px ahead of its plane (its near tooth stands 0.68 in nearer the lens)","via":"harvest"}}]},"rear_x":{"label":"The tail cap's end behind the clamp's middle","kind":"length","measurements":[{"id":"photo","value":2.483,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 96bbc99c1b2a (Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720)","scaleRef":"the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000 (.cache/batch123/streamlight-protac-rail-mount-hl-x/cam_fit.py)","method":"the tail guard's tip shows at column 2023.4, 18.9 px behind its plane (its near ear stands 0.46 in nearer the lens)","via":"harvest"}}],"note":"With the push-button tail cap. front_x and rear_x add up to the published length: the scale was set so."},"clamp_length":{"label":"The clamp's length along the rail (its moving jaw)","kind":"length","measurements":[{"id":"photo","value":1.215,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 96bbc99c1b2a (Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720)","scaleRef":"the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000 (.cache/batch123/streamlight-protac-rail-mount-hl-x/cam_fit.py)","method":"the moving jaw's block, columns 934 to 1356 (its corners chamfered 0.12 in); the fixed jaw on the other side is 1.09 (958 to 1338)","via":"harvest"}}]},"fixed_jaw_length":{"label":"The fixed jaw's length along the rail","kind":"length","measurements":[{"id":"photo","value":1.094,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 96bbc99c1b2a (Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720)","scaleRef":"the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000 (.cache/batch123/streamlight-protac-rail-mount-hl-x/cam_fit.py)","method":"columns 958 to 1338, its two mounting screws' heads at its ends","via":"harvest"}}]},"moving_jaw_z":{"label":"The moving jaw's outer face from the body's axis (as photographed)","kind":"length","measurements":[{"id":"photo","value":0.673,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 96bbc99c1b2a (Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720)","scaleRef":"the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000 (.cache/batch123/streamlight-protac-rail-mount-hl-x/cam_fit.py)","method":"the block's flat outer face at row 556.9, the axis at row 790.6 there: 233.7 px. The jaw moves with the wheel: how far open the clamp is in the photo isn't known","via":"harvest"}}]},"fixed_jaw_z":{"label":"The fixed jaw's outer face from the body's axis","kind":"length","measurements":[{"id":"photo","value":0.55,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 96bbc99c1b2a (Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720)","scaleRef":"the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000 (.cache/batch123/streamlight-protac-rail-mount-hl-x/cam_fit.py)","method":"the jaw's raised middle at row 981.8, the axis at 790.6: 191.2 px. Its face either side is 0.025 in lower (row 973), and its two screws' heads stand 0.022 in off that","via":"harvest"}}]},"jaw_height":{"label":"The jaws' height (top to bottom of the fixed jaw's face)","kind":"length","measurements":[{"id":"kit","value":0.52,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 5e8b2b975914 (GRITR's copy of the maker's kit picture for 88071: the light from its left side and from about 30 degrees above, the clamp's fixed jaw toward the lens, 1601 x 1601; engraved S/N 358732 0522)","scaleRef":"the tube's width there, 141.5 px, as .body_diameter: 153.8 px/in","method":"the fixed jaw's face from its top edge (row 485) to its bottom (row 554), 69 px, over the cosine of the view's angle above the side (32 degrees, from where the engraving shows; 25 to 39 changes it by 0.04)","via":"harvest"}}]},"moving_jaw_height":{"label":"The moving jaw's height","kind":"length","measurements":[{"id":"oblique","value":0.376,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 0c0f9c6bb6f9 (Primary Arms 88066_01.jpg: the same unit from behind and above, thumb wheel toward the lens, 2200 x 1467)","scaleRef":"the camera fitted to the body in that photo (as bolt_below_axis: focal length 8000 px, the lens 19.3 in off) and the turn about the axis the stud's end gives","method":"the jaw's rear outer corner edge from its top (pixel 1043, 1030) to its foot (1036, 1179): 0.512 and 0.888 in below the body's axis; the chamfer along its lower edge is 0.04 of that","via":"harvest"}}],"note":"Shorter than the fixed jaw (jaw_height, 0.52 from the kit picture), which carries the two mounting screws above the cross bolt."},"jaw_below_bolt":{"label":"The jaws' lower edge below the cross bolt's axis","kind":"length","measurements":[{"id":"kit","value":0.1,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 5e8b2b975914 (GRITR's copy of the maker's kit picture for 88071: the light from its left side and from about 30 degrees above, the clamp's fixed jaw toward the lens, 1601 x 1601; engraved S/N 358732 0522)","scaleRef":"the tube's width there, 141.5 px, as .body_diameter: 153.8 px/in","method":"the bolt head's centre (row 540) to the jaw's lower edge (row 554), 14 px, over the cosine of 32 degrees","via":"harvest"}},{"id":"oblique","value":0.082,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 0c0f9c6bb6f9 (Primary Arms 88066_01.jpg: the same unit from behind and above, thumb wheel toward the lens, 2200 x 1467)","scaleRef":"the camera fitted to the body in that photo (as bolt_below_axis: focal length 8000 px, the lens 19.3 in off) and the turn about the axis the stud's end gives","method":"the moving jaw's rear outer corner edge, taken as standing square to the rail at the jaw's rear end (x = -clamp_length / 2): its foot, with the chamfer along the jaw's lower edge, at pixel (1036, 1179) is 0.888 in below the body's axis, the bolt 0.807 (.cache/batch123/streamlight-protac-rail-mount-hl-x)","via":"harvest"}}],"adopt":{"from":"oblique","reason":"Read through a fitted camera; the kit picture's reading on the other jaw depends on its angle, and agrees within both +/-."}},"screw_above_bolt":{"label":"The two mounting screws above the cross bolt's axis","kind":"length","measurements":[{"id":"kit","value":0.18,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 5e8b2b975914 (GRITR's copy of the maker's kit picture for 88071: the light from its left side and from about 30 degrees above, the clamp's fixed jaw toward the lens, 1601 x 1601; engraved S/N 358732 0522)","scaleRef":"the tube's width there, 141.5 px, as .body_diameter: 153.8 px/in","method":"the screw heads' centres (rows 513.5 and 520, the picture turned 1.2 degrees) 23 px above the bolt head's, over the cosine of 32 degrees","via":"harvest"}}]},"screw_spacing":{"label":"The two mounting screws, centre to centre along the rail","kind":"length","measurements":[{"id":"photo","value":0.895,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 96bbc99c1b2a (Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720)","scaleRef":"the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000 (.cache/batch123/streamlight-protac-rail-mount-hl-x/cam_fit.py)","method":"their heads' middles at columns 992.5 and 1303.5 (each head 68 px, 0.196 in, across)","via":"harvest"}}]},"screw_head_diameter":{"label":"The mounting screws' head diameter","kind":"length","measurements":[{"id":"photo","value":0.196,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 96bbc99c1b2a (Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720)","scaleRef":"the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000 (.cache/batch123/streamlight-protac-rail-mount-hl-x/cam_fit.py)","method":"each head 68 px across where it stands off the fixed jaw (columns 958 to 1026 and 1270 to 1337)","via":"harvest"}}]},"bolt_head_diameter":{"label":"The cross bolt's head on the fixed jaw","kind":"length","measurements":[{"id":"kit","value":0.23,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 5e8b2b975914 (GRITR's copy of the maker's kit picture for 88071: the light from its left side and from about 30 degrees above, the clamp's fixed jaw toward the lens, 1601 x 1601; engraved S/N 358732 0522)","scaleRef":"the tube's width there, 141.5 px, as .body_diameter: 153.8 px/in","method":"the round head at the jaw's lower edge, 35 px across along the light","via":"harvest"}}]},"wheel_diameter":{"label":"The thumb wheel's diameter","kind":"length","measurements":[{"id":"photo","value":0.625,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 96bbc99c1b2a (Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720)","scaleRef":"the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000 (.cache/batch123/streamlight-protac-rail-mount-hl-x/cam_fit.py)","method":"columns 1034 to 1250 at rows 440 to 520: 217 px","via":"harvest"}}]},"wheel_thickness":{"label":"The thumb wheel's thickness (its knurled rim)","kind":"length","measurements":[{"id":"photo","value":0.262,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 96bbc99c1b2a (Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720)","scaleRef":"the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000 (.cache/batch123/streamlight-protac-rail-mount-hl-x/cam_fit.py)","method":"rows 434 to 525: 91 px; a collar 0.41 in across (141 px) carries it 0.09 in off the jaw (rows 525 to 557)","via":"harvest"}}]},"wheel_end_z":{"label":"The stud's end beyond the wheel, from the body's axis (as photographed)","kind":"length","measurements":[{"id":"photo","value":1.05,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 96bbc99c1b2a (Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720)","scaleRef":"the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000 (.cache/batch123/streamlight-protac-rail-mount-hl-x/cam_fit.py)","method":"the stud's end at row 426.1, the axis at 790.6: 364.5 px; the wheel's own outer face is 0.017 in short of it (row 432)","via":"harvest"}}]},"collar_diameter":{"label":"The collar between the thumb wheel and the moving jaw","kind":"length","measurements":[{"id":"photo","value":0.406,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 96bbc99c1b2a (Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720)","scaleRef":"the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000 (.cache/batch123/streamlight-protac-rail-mount-hl-x/cam_fit.py)","method":"columns 1073 to 1213 at row 540: 141 px","via":"harvest"}}]},"band_diameter":{"label":"The two bands on the body that the clamp's legs hang from","kind":"length","measurements":[{"id":"photo","value":0.933,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 96bbc99c1b2a (Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720)","scaleRef":"the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000 (.cache/batch123/streamlight-protac-rail-mount-hl-x/cam_fit.py)","method":"the band's lower edge where it shows ahead of the fixed jaw (columns 936 to 956): 162.0 px from the axis, the tube 159.8","via":"harvest"}}]},"waist_diameter":{"label":"The body between the two bands (where it is engraved)","kind":"length","measurements":[{"id":"kit","value":0.852,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 5e8b2b975914 (GRITR's copy of the maker's kit picture for 88071: the light from its left side and from about 30 degrees above, the clamp's fixed jaw toward the lens, 1601 x 1601; engraved S/N 358732 0522)","scaleRef":"the tube's width there, 141.5 px, as .body_diameter: 153.8 px/in","method":"the body's upper edge stands 6.2 px lower between the bands (row 320.1 over columns 740 to 812) than on the front band (312.5) and the rear one (314.9), the picture's 1.2 degree turn allowed for: 0.040 in under the bands' radius (.band_diameter). The tube beside the rear band is 1 px under it, as the plan view has it","via":"harvest"}}],"note":"A turned body's upper edge shows its radius from any side, so the kit picture's angle doesn't matter here. In the plan view the clamp's jaws hide this zone's sides."},"band_front_x":{"label":"The front band's front edge ahead of the clamp's middle","kind":"length","measurements":[{"id":"photo","value":0.605,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 96bbc99c1b2a (Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720)","scaleRef":"the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000 (.cache/batch123/streamlight-protac-rail-mount-hl-x/cam_fit.py)","method":"column 932 (the clamp's middle at 1142); the band runs back to column 1060, 0.37 in","via":"harvest"}}]},"band_rear_x":{"label":"The rear band's rear edge behind the clamp's middle","kind":"length","measurements":[{"id":"photo","value":0.622,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 96bbc99c1b2a (Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720)","scaleRef":"the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000 (.cache/batch123/streamlight-protac-rail-mount-hl-x/cam_fit.py)","method":"column 1358; the band runs forward to column 1255, 0.30 in","via":"harvest"}}]},"band_length":{"label":"Each band's (and each leg's) length along the body","kind":"length","measurements":[{"id":"photo","value":0.33,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 96bbc99c1b2a (Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720)","scaleRef":"the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000 (.cache/batch123/streamlight-protac-rail-mount-hl-x/cam_fit.py)","method":"the front band 128 px (0.37 in), the rear one 103 px (0.30): their mean; the +/- takes in both","via":"harvest"}}]},"lens_diameter":{"label":"The glass as it shows inside the bezel","kind":"length","measurements":[{"id":"photo","value":1.05,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 7544feb9932f (Primary Arms 88066_02.jpg: the same unit from ahead, 2200 x 1467)","scaleRef":"the bezel's own diameter across the same line, 426 px, as 1.365 in (profiles.body: 474.2 px in the plan view)","method":"the luminance across the head's front face through its centre (416, 1196), square to the body's axis in the picture: bright from 160 px one side to 168 px the other, the bezel's wall dark outside it","via":"harvest"}}]},"jaw_chamfer":{"label":"The moving jaw's corner chamfers (in plan)","kind":"length","measurements":[{"id":"photo","value":0.12,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 96bbc99c1b2a (Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720)","scaleRef":"347.3 px/in at the axis (as body_diameter: the published length less the end rims' perspective)","method":"each end of the block's outer face is cut back from column 934 to 976 (42 px along) and from row 594 to 557 (37 px across)","via":"harvest"}}]},"wheel_face_z":{"label":"The thumb wheel's outer face from the body's axis (as photographed)","kind":"length","measurements":[{"id":"photo","value":1.033,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 96bbc99c1b2a (Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720)","scaleRef":"347.3 px/in at the axis (as body_diameter: the published length less the end rims' perspective)","method":"the wheel's rim ends at row 432 (the axis at 790.6): 358.6 px","via":"harvest"}}]},"jaw_face_step":{"label":"The fixed jaw's raised middle above the face either side of it","kind":"length","measurements":[{"id":"photo","value":0.025,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 96bbc99c1b2a (Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720)","scaleRef":"347.3 px/in at the axis (as body_diameter: the published length less the end rims' perspective)","method":"rows 981.8 (the middle) and 973 (the face beside the screw heads): 8.8 px","via":"harvest"}}]},"jaw_pad_length":{"label":"The fixed jaw's raised middle, its length along the rail","kind":"length","measurements":[{"id":"photo","value":0.54,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 96bbc99c1b2a (Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720)","scaleRef":"347.3 px/in at the axis (as body_diameter: the published length less the end rims' perspective)","method":"columns 1055 to 1243: 188 px","via":"harvest"}}]},"lugs":{"label":"M-LOK slots its mount's lugs span","kind":"count","measurements":[{"id":"photo","value":1,"unit":"count","source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 83f4380a7ffe (Streamlight's gallery image _5: a handguard from its right side, the light on its M-LOK mount, 800 x 800)","scaleRef":"the handguard's M-LOK slots: 61.2 px to the 40 mm pitch (std.mlok.slot_pitch)","method":"the mount's plate (columns 464 to 520) covers the slot between the ones at 407 to 455 and 530 to 578; its two screws at columns 477 and 508","via":"harvest"}}],"note":"The M-LOK mount (Streamlight item 88300, in both packages; modelled since 2026-10-19, batch 13: the mlok_ entries below). Its two T-nut screws are 31 px apart in the maker's side view (20.3 mm by the slots' pitch) and both sit in one slot, which its plate covers; Streamlight's _4 and its HL-X Pro and Rail Mount 2 pictures (40f51d600bbb, 39df28d719d2) show the same, each a three-quarter view."},"reach_inside":{"label":"Reach inside the handguard (below the mounting face, tightened)","kind":"length","measurements":[],"note":"Not sourced: the instruction sheet gives the M-LOK mount's screws (10-24 x 3/8 in) and no T-nut figure."},"mlok_length":{"label":"The M-LOK mount's length (its plate and seat, one section along it)","kind":"length","measurements":[{"id":"fit","value":1.498,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 5985240ddec1, c7132f20d430, 0279000d1c9d, 8a7867bb8d09 (milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L)","scaleRef":"the plate's two holes, std.mlok.interval (20 mm) apart: an M-LOK accessory's two T-nuts in one slot (the maker's side view of the light on its mount reads 20.3 mm: mlok_screw_spacing)","method":"a pinhole camera for each photo and the mount's section fitted together (the mount is one section along its length: the plate, the seat standing from the plate's top edge at an angle to it, two lips along the seat and the floor between them; holes through each leg), to 57 points read on the four photos: corners at both ends, the plate's lower edge, the lips' edges, the inner corner, and the holes' see-through middles, taken at the middle of each hole's through part. rms 1.49 of the points' stated ± (.cache/batch13/streamlight-protac-rail-mount-hl-x/fit.py, obs5.json, fit_ABCD.json). The ± is twice the fit's own, wider than the spread of the four fits that each leave one photo out (the seat's angle 128.4 to 130.8 degrees, its width 17.2 to 18.2 mm): the mount's length (38.1 mm)","via":"harvest"}},{"id":"maker-side","value":1.49,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 83f4380a7ffe (Streamlight's gallery image _5: a handguard from its right side, the HL-X on its M-LOK mount, 800 x 800)","scaleRef":"the handguard's M-LOK slots: 61.2 px to the 40 mm pitch (std.mlok.slot_pitch), 38.9 px/in in the face's plane","method":"the plate's two ends, columns 464 to 522 (58 px); one pixel is 0.026 in","via":"harvest"}}],"adopt":{"from":"fit","reason":"Four photos of the mount alone through fitted cameras; the maker's side view of it on a handguard, at 39 px to the inch, agrees."}},"mlok_plate_height":{"label":"The mount's plate: from the corner down its outer face to its lower edge","kind":"length","measurements":[{"id":"fit","value":0.798,"unit":"in","pm":0.042,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 5985240ddec1, c7132f20d430, 0279000d1c9d, 8a7867bb8d09 (milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L)","scaleRef":"the plate's two holes, std.mlok.interval (20 mm) apart: an M-LOK accessory's two T-nuts in one slot (the maker's side view of the light on its mount reads 20.3 mm: mlok_screw_spacing)","method":"a pinhole camera for each photo and the mount's section fitted together (the mount is one section along its length: the plate, the seat standing from the plate's top edge at an angle to it, two lips along the seat and the floor between them; holes through each leg), to 57 points read on the four photos: corners at both ends, the plate's lower edge, the lips' edges, the inner corner, and the holes' see-through middles, taken at the middle of each hole's through part. rms 1.49 of the points' stated ± (.cache/batch13/streamlight-protac-rail-mount-hl-x/fit.py, obs5.json, fit_ABCD.json). The ± is twice the fit's own, wider than the spread of the four fits that each leave one photo out (the seat's angle 128.4 to 130.8 degrees, its width 17.2 to 18.2 mm): the plate's outer face from the corner to its lower edge (20.3 mm)","via":"harvest"}},{"id":"maker-side","value":0.784,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 83f4380a7ffe (Streamlight's gallery image _5: a handguard from its right side, the HL-X on its M-LOK mount, 800 x 800)","scaleRef":"the handguard's M-LOK slots: 61.2 px to the 40 mm pitch (std.mlok.slot_pitch), 38.9 px/in in the face's plane","method":"the plate's outer face from its top edge (row 302.5, under the lit band of the seat's lip tops) to its lower edge (row 333): 30.5 px","via":"harvest"}}],"adopt":{"from":"fit","reason":"Four photos of the mount alone through fitted cameras; the maker's side view of it on a handguard agrees."}},"mlok_plate_thickness":{"label":"The mount's plate thickness (outer face to the face on the handguard)","kind":"length","measurements":[{"id":"fit","value":0.216,"unit":"in","pm":0.033,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 5985240ddec1, c7132f20d430, 0279000d1c9d, 8a7867bb8d09 (milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L)","scaleRef":"the plate's two holes, std.mlok.interval (20 mm) apart: an M-LOK accessory's two T-nuts in one slot (the maker's side view of the light on its mount reads 20.3 mm: mlok_screw_spacing)","method":"a pinhole camera for each photo and the mount's section fitted together (the mount is one section along its length: the plate, the seat standing from the plate's top edge at an angle to it, two lips along the seat and the floor between them; holes through each leg), to 57 points read on the four photos: corners at both ends, the plate's lower edge, the lips' edges, the inner corner, and the holes' see-through middles, taken at the middle of each hole's through part. rms 1.49 of the points' stated ± (.cache/batch13/streamlight-protac-rail-mount-hl-x/fit.py, obs5.json, fit_ABCD.json). The ± is twice the fit's own, wider than the spread of the four fits that each leave one photo out (the seat's angle 128.4 to 130.8 degrees, its width 17.2 to 18.2 mm): the plate's thickness (5.5 mm), at its ends and its lower edge","via":"harvest"}}]},"mlok_seat_angle":{"label":"The angle inside the mount between its plate and its seat","kind":"angle","measurements":[{"id":"fit","value":129.5,"unit":"deg","pm":4,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 5985240ddec1, c7132f20d430, 0279000d1c9d, 8a7867bb8d09 (milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L)","scaleRef":"the plate's two holes, std.mlok.interval (20 mm) apart: an M-LOK accessory's two T-nuts in one slot (the maker's side view of the light on its mount reads 20.3 mm: mlok_screw_spacing)","method":"a pinhole camera for each photo and the mount's section fitted together (the mount is one section along its length: the plate, the seat standing from the plate's top edge at an angle to it, two lips along the seat and the floor between them; holes through each leg), to 57 points read on the four photos: corners at both ends, the plate's lower edge, the lips' edges, the inner corner, and the holes' see-through middles, taken at the middle of each hole's through part. rms 1.49 of the points' stated ± (.cache/batch13/streamlight-protac-rail-mount-hl-x/fit.py, obs5.json, fit_ABCD.json). The ± is twice the fit's own, wider than the spread of the four fits that each leave one photo out (the seat's angle 128.4 to 130.8 degrees, its width 17.2 to 18.2 mm): the angle between the plate's outer face and the seat's lip tops, inside the L (129.5 degrees)","via":"harvest"}},{"id":"fits","value":135,"unit":"deg","pm":1,"source":{"type":"derived","basis":"What the mount has to fit, not a reading: the handguards' faces above a side row of M-LOK slots stand at 45 degrees to it (the octagons' faces 45 degrees apart: BCM's MCMR's mlok and mlok_between faces at 90 and 45, Geissele's MK16's at 90 and 45), and the seat's inner face lies over that face; at a smaller angle it stands into it.","via":"harvest"}}],"adopt":{"from":"fits","reason":"Decided by what it has to fit (the mount is sold for M-LOK handguards, and Streamlight's own pictures have it on one over its top corner); the photos' figure, 1.4 of its ± away, stays beside it."},"note":"Wider than a right angle: on a handguard's side face the seat rises toward the handguard from the plate's top edge, and the light on it leans out from upright by the angle less 90 degrees. In milgear's view from above (71643) the two legs' holes are both nearly round (0.84 and 0.81 of a circle as they show through), which two faces at a right angle can't both be; the inside view (71642) is too close to read an angle off by eye. 1lumen's reviewer (in the discovery's reading of a page the harvester was refused): \"You can orient the M-LOK adapter to slant either way\"."},"mlok_seat_width":{"label":"The mount's seat: from the corner across its lip tops to the far lip's outer edge","kind":"length","measurements":[{"id":"fit","value":0.689,"unit":"in","pm":0.046,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 5985240ddec1, c7132f20d430, 0279000d1c9d, 8a7867bb8d09 (milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L)","scaleRef":"the plate's two holes, std.mlok.interval (20 mm) apart: an M-LOK accessory's two T-nuts in one slot (the maker's side view of the light on its mount reads 20.3 mm: mlok_screw_spacing)","method":"a pinhole camera for each photo and the mount's section fitted together (the mount is one section along its length: the plate, the seat standing from the plate's top edge at an angle to it, two lips along the seat and the floor between them; holes through each leg), to 57 points read on the four photos: corners at both ends, the plate's lower edge, the lips' edges, the inner corner, and the holes' see-through middles, taken at the middle of each hole's through part. rms 1.49 of the points' stated ± (.cache/batch13/streamlight-protac-rail-mount-hl-x/fit.py, obs5.json, fit_ABCD.json). The ± is twice the fit's own, wider than the spread of the four fits that each leave one photo out (the seat's angle 128.4 to 130.8 degrees, its width 17.2 to 18.2 mm): the seat's width over the lips (17.5 mm)","via":"harvest"}}]},"mlok_near_lip_width":{"label":"The seat's near lip (at the corner): its top's width","kind":"length","measurements":[{"id":"fit","value":0.22,"unit":"in","pm":0.033,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 5985240ddec1, c7132f20d430, 0279000d1c9d, 8a7867bb8d09 (milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L)","scaleRef":"the plate's two holes, std.mlok.interval (20 mm) apart: an M-LOK accessory's two T-nuts in one slot (the maker's side view of the light on its mount reads 20.3 mm: mlok_screw_spacing)","method":"a pinhole camera for each photo and the mount's section fitted together (the mount is one section along its length: the plate, the seat standing from the plate's top edge at an angle to it, two lips along the seat and the floor between them; holes through each leg), to 57 points read on the four photos: corners at both ends, the plate's lower edge, the lips' edges, the inner corner, and the holes' see-through middles, taken at the middle of each hole's through part. rms 1.49 of the points' stated ± (.cache/batch13/streamlight-protac-rail-mount-hl-x/fit.py, obs5.json, fit_ABCD.json). The ± is twice the fit's own, wider than the spread of the four fits that each leave one photo out (the seat's angle 128.4 to 130.8 degrees, its width 17.2 to 18.2 mm): the near lip's top, the corner to its inner edge (5.6 mm)","via":"harvest"}}]},"mlok_far_lip_width":{"label":"The seat's far lip: its top's width","kind":"length","measurements":[{"id":"fit","value":0.11,"unit":"in","pm":0.029,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 5985240ddec1, c7132f20d430, 0279000d1c9d, 8a7867bb8d09 (milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L)","scaleRef":"the plate's two holes, std.mlok.interval (20 mm) apart: an M-LOK accessory's two T-nuts in one slot (the maker's side view of the light on its mount reads 20.3 mm: mlok_screw_spacing)","method":"a pinhole camera for each photo and the mount's section fitted together (the mount is one section along its length: the plate, the seat standing from the plate's top edge at an angle to it, two lips along the seat and the floor between them; holes through each leg), to 57 points read on the four photos: corners at both ends, the plate's lower edge, the lips' edges, the inner corner, and the holes' see-through middles, taken at the middle of each hole's through part. rms 1.49 of the points' stated ± (.cache/batch13/streamlight-protac-rail-mount-hl-x/fit.py, obs5.json, fit_ABCD.json). The ± is twice the fit's own, wider than the spread of the four fits that each leave one photo out (the seat's angle 128.4 to 130.8 degrees, its width 17.2 to 18.2 mm): the far lip's top, its inner edge to the seat's far edge (2.8 mm)","via":"harvest"}}]},"mlok_lip_height":{"label":"The lips' height above the seat's floor (where the light's legs stand)","kind":"length","measurements":[{"id":"fit","value":0.064,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 5985240ddec1, c7132f20d430, 0279000d1c9d, 8a7867bb8d09 (milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L)","scaleRef":"the plate's two holes, std.mlok.interval (20 mm) apart: an M-LOK accessory's two T-nuts in one slot (the maker's side view of the light on its mount reads 20.3 mm: mlok_screw_spacing)","method":"a pinhole camera for each photo and the mount's section fitted together (the mount is one section along its length: the plate, the seat standing from the plate's top edge at an angle to it, two lips along the seat and the floor between them; holes through each leg), to 57 points read on the four photos: corners at both ends, the plate's lower edge, the lips' edges, the inner corner, and the holes' see-through middles, taken at the middle of each hole's through part. rms 1.49 of the points' stated ± (.cache/batch13/streamlight-protac-rail-mount-hl-x/fit.py, obs5.json, fit_ABCD.json). The ± is twice the fit's own, wider than the spread of the four fits that each leave one photo out (the seat's angle 128.4 to 130.8 degrees, its width 17.2 to 18.2 mm): the floor below the lip tops (1.6 mm)","via":"harvest"}}]},"mlok_seat_thickness":{"label":"The seat's thickness, the lip tops to its inner face","kind":"length","measurements":[{"id":"fit","value":0.226,"unit":"in","pm":0.032,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 5985240ddec1, c7132f20d430, 0279000d1c9d, 8a7867bb8d09 (milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L)","scaleRef":"the plate's two holes, std.mlok.interval (20 mm) apart: an M-LOK accessory's two T-nuts in one slot (the maker's side view of the light on its mount reads 20.3 mm: mlok_screw_spacing)","method":"a pinhole camera for each photo and the mount's section fitted together (the mount is one section along its length: the plate, the seat standing from the plate's top edge at an angle to it, two lips along the seat and the floor between them; holes through each leg), to 57 points read on the four photos: corners at both ends, the plate's lower edge, the lips' edges, the inner corner, and the holes' see-through middles, taken at the middle of each hole's through part. rms 1.49 of the points' stated ± (.cache/batch13/streamlight-protac-rail-mount-hl-x/fit.py, obs5.json, fit_ABCD.json). The ± is twice the fit's own, wider than the spread of the four fits that each leave one photo out (the seat's angle 128.4 to 130.8 degrees, its width 17.2 to 18.2 mm): the seat from its lip tops to its inner face (5.7 mm)","via":"harvest"}}]},"mlok_screw_below_corner":{"label":"The plate's two screws (the T-nuts' middle line) below the corner","kind":"length","measurements":[{"id":"fit","value":0.417,"unit":"in","pm":0.031,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 5985240ddec1, c7132f20d430, 0279000d1c9d, 8a7867bb8d09 (milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L)","scaleRef":"the plate's two holes, std.mlok.interval (20 mm) apart: an M-LOK accessory's two T-nuts in one slot (the maker's side view of the light on its mount reads 20.3 mm: mlok_screw_spacing)","method":"a pinhole camera for each photo and the mount's section fitted together (the mount is one section along its length: the plate, the seat standing from the plate's top edge at an angle to it, two lips along the seat and the floor between them; holes through each leg), to 57 points read on the four photos: corners at both ends, the plate's lower edge, the lips' edges, the inner corner, and the holes' see-through middles, taken at the middle of each hole's through part. rms 1.49 of the points' stated ± (.cache/batch13/streamlight-protac-rail-mount-hl-x/fit.py, obs5.json, fit_ABCD.json). The ± is twice the fit's own, wider than the spread of the four fits that each leave one photo out (the seat's angle 128.4 to 130.8 degrees, its width 17.2 to 18.2 mm): the plate's holes' line, on its outer face, below the corner (10.6 mm)","via":"harvest"}},{"id":"maker-side","value":0.424,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 83f4380a7ffe (Streamlight's gallery image _5: a handguard from its right side, the HL-X on its M-LOK mount, 800 x 800)","scaleRef":"the handguard's M-LOK slots: 61.2 px to the 40 mm pitch (std.mlok.slot_pitch), 38.9 px/in in the face's plane","method":"the plate's top edge (row 302.5) to its two screws' middles (row 319): 16.5 px","via":"harvest"}}],"adopt":{"from":"fit","reason":"Four photos of the mount alone through fitted cameras; the maker's side view of it on a handguard agrees."}},"mlok_screw_spacing":{"label":"The plate's two screws (its T-nuts), centre to centre","kind":"length","measurements":[{"id":"interval","value":0.787,"unit":"in","pm":0.004,"source":{"type":"derived","expr":"{std.mlok.interval}","via":"harvest"}},{"id":"maker-photo","value":20.3,"unit":"mm","pm":0.7,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 83f4380a7ffe (Streamlight's gallery image _5: a handguard from its right side, the light on its M-LOK mount, 800 x 800)","scaleRef":"the handguard's M-LOK slots: 61.2 px to the 40 mm pitch (std.mlok.slot_pitch)","method":"the two screw heads' middles, columns 477 and 508: 31 px; one pixel is 0.65 mm","via":"harvest"}}],"adopt":{"from":"interval","reason":"The standard's interval, which every two-nut M-LOK part on file is placed by; the maker's own side view of the mount reads it within a pixel."},"note":"Both in the one slot the plate is centred on, in every installed photo on file (the maker's side view, its _4 and two siblings' pictures): an accessory's two T-nuts stand the M-LOK interval apart, one in each half of a slot (data/interfaces.yaml)."},"mlok_screw_hole_diameter":{"label":"The plate's screw holes (10-24 clearance), diameter","kind":"length","measurements":[{"id":"photo","value":0.215,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x c7132f20d430 (milgear.fi 71643: the mount 88300 laid with the kit, both legs' outer faces toward the lens from above, 1400 x 979)","scaleRef":"the plate's two holes, std.mlok.interval (20 mm) apart: 234.9 px, 11.745 px/mm across the plate (the seat's length, 446 px against the plate's 453, puts the seat 1.5% further off)","method":"each hole's see-through width along the plate (the plate is turned about its length, so across it the far rim cuts the opening): 64.3 and 64.2 px","via":"harvest"}}]},"mlok_counterbore_diameter":{"label":"The plate's counterbores (for the 10-24 button heads), diameter at its outer face","kind":"length","measurements":[{"id":"photo","value":0.374,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x c7132f20d430 (milgear.fi 71643: the mount 88300 laid with the kit, both legs' outer faces toward the lens from above, 1400 x 979)","scaleRef":"the plate's two holes, std.mlok.interval (20 mm) apart: 234.9 px, 11.745 px/mm across the plate (the seat's length, 446 px against the plate's 453, puts the seat 1.5% further off)","method":"each counterbore's rim along the plate, columns 427 to 537 and 662 to 775: 110 and 113 px","via":"harvest"}}]},"mlok_counterbore_depth":{"label":"The plate's counterbores, depth from its outer face","kind":"length","measurements":[{"id":"fit","value":0.066,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 5985240ddec1, c7132f20d430, 0279000d1c9d, 8a7867bb8d09 (milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L)","scaleRef":"the plate's two holes, std.mlok.interval (20 mm) apart: an M-LOK accessory's two T-nuts in one slot (the maker's side view of the light on its mount reads 20.3 mm: mlok_screw_spacing)","method":"a pinhole camera for each photo and the mount's section fitted together (the mount is one section along its length: the plate, the seat standing from the plate's top edge at an angle to it, two lips along the seat and the floor between them; holes through each leg), to 57 points read on the four photos: corners at both ends, the plate's lower edge, the lips' edges, the inner corner, and the holes' see-through middles, taken at the middle of each hole's through part. rms 1.49 of the points' stated ± (.cache/batch13/streamlight-protac-rail-mount-hl-x/fit.py, obs5.json, fit_ABCD.json). The ± is twice the fit's own, wider than the spread of the four fits that each leave one photo out (the seat's angle 128.4 to 130.8 degrees, its width 17.2 to 18.2 mm): the counterbores' floor below the outer face (1.7 mm), read only through where the holes' see-through middles fall: the weakest figure of the fit","via":"harvest"}}]},"mlok_seat_hole_diameter":{"label":"The seat's two holes (8-32 clearance), diameter","kind":"length","measurements":[{"id":"photo","value":0.176,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x c7132f20d430 (milgear.fi 71643: the mount 88300 laid with the kit, both legs' outer faces toward the lens from above, 1400 x 979)","scaleRef":"the plate's two holes, std.mlok.interval (20 mm) apart: 234.9 px, 11.745 px/mm across the plate (the seat's length, 446 px against the plate's 453, puts the seat 1.5% further off)","method":"each hole's see-through width along the seat: 51.6 and 51.8 px, at the seat's scale (1.5% under the plate's)","via":"harvest"}}]},"mlok_seat_hole_spacing":{"label":"The seat's two holes (the light's two ports under its legs), centre to centre","kind":"length","measurements":[{"id":"fit","value":0.852,"unit":"in","pm":0.045,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 5985240ddec1, c7132f20d430, 0279000d1c9d, 8a7867bb8d09 (milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L)","scaleRef":"the plate's two holes, std.mlok.interval (20 mm) apart: an M-LOK accessory's two T-nuts in one slot (the maker's side view of the light on its mount reads 20.3 mm: mlok_screw_spacing)","method":"a pinhole camera for each photo and the mount's section fitted together (the mount is one section along its length: the plate, the seat standing from the plate's top edge at an angle to it, two lips along the seat and the floor between them; holes through each leg), to 57 points read on the four photos: corners at both ends, the plate's lower edge, the lips' edges, the inner corner, and the holes' see-through middles, taken at the middle of each hole's through part. rms 1.49 of the points' stated ± (.cache/batch13/streamlight-protac-rail-mount-hl-x/fit.py, obs5.json, fit_ABCD.json). The ± is twice the fit's own, wider than the spread of the four fits that each leave one photo out (the seat's angle 128.4 to 130.8 degrees, its width 17.2 to 18.2 mm): the seat's holes' middles (21.7 mm); in the view from above alone, 254.7 px at the seat's scale, 22.0 mm","via":"harvest"}}],"note":"The light's legs' middles are 0.897 in apart by the bands they hang from (band_front_x, band_rear_x, band_length): each hole is inside its leg."},"mlok_seat_hole_from_corner":{"label":"The seat's holes' line across the seat from the corner","kind":"length","measurements":[{"id":"fit","value":0.402,"unit":"in","pm":0.039,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 5985240ddec1, c7132f20d430, 0279000d1c9d, 8a7867bb8d09 (milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L)","scaleRef":"the plate's two holes, std.mlok.interval (20 mm) apart: an M-LOK accessory's two T-nuts in one slot (the maker's side view of the light on its mount reads 20.3 mm: mlok_screw_spacing)","method":"a pinhole camera for each photo and the mount's section fitted together (the mount is one section along its length: the plate, the seat standing from the plate's top edge at an angle to it, two lips along the seat and the floor between them; holes through each leg), to 57 points read on the four photos: corners at both ends, the plate's lower edge, the lips' edges, the inner corner, and the holes' see-through middles, taken at the middle of each hole's through part. rms 1.49 of the points' stated ± (.cache/batch13/streamlight-protac-rail-mount-hl-x/fit.py, obs5.json, fit_ABCD.json). The ± is twice the fit's own, wider than the spread of the four fits that each leave one photo out (the seat's angle 128.4 to 130.8 degrees, its width 17.2 to 18.2 mm): the seat's holes' line from the corner along the lip tops (10.2 mm)","via":"harvest"}}],"note":"The middle of the floor between the lips is 0.401 in from the corner (mlok_near_lip_width, mlok_seat_width, mlok_far_lip_width): the holes, and the light's legs on them, are on it."},"mlok_seat_counterbore_diameter":{"label":"The seat's counterbores (for the 8-32 heads, on its inner face), diameter","kind":"length","measurements":[{"id":"photo","value":0.3,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 8a7867bb8d09 (milgear.fi 71642: inside the mount's L, the plate's inner face up, 1400 x 980)","scaleRef":"the plate's two holes, std.mlok.interval (20 mm) apart: 368 px, 18.4 px/mm on the plate's inner face; the seat's face stands further off and is turned (no camera fitted to this view): the ± allows 10%","method":"the left counterbore's rim across its widest, columns 508 to 650","via":"harvest"}}]},"mlok_seat_counterbore_depth":{"label":"The seat's counterbores, depth from its inner face","kind":"length","measurements":[{"id":"fit","value":0.074,"unit":"in","pm":0.066,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 5985240ddec1, c7132f20d430, 0279000d1c9d, 8a7867bb8d09 (milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L)","scaleRef":"the plate's two holes, std.mlok.interval (20 mm) apart: an M-LOK accessory's two T-nuts in one slot (the maker's side view of the light on its mount reads 20.3 mm: mlok_screw_spacing)","method":"a pinhole camera for each photo and the mount's section fitted together (the mount is one section along its length: the plate, the seat standing from the plate's top edge at an angle to it, two lips along the seat and the floor between them; holes through each leg), to 57 points read on the four photos: corners at both ends, the plate's lower edge, the lips' edges, the inner corner, and the holes' see-through middles, taken at the middle of each hole's through part. rms 1.49 of the points' stated ± (.cache/batch13/streamlight-protac-rail-mount-hl-x/fit.py, obs5.json, fit_ABCD.json). The ± is twice the fit's own, wider than the spread of the four fits that each leave one photo out (the seat's angle 128.4 to 130.8 degrees, its width 17.2 to 18.2 mm): the counterbores' floor above the seat's inner face (1.9 mm), read only through where the holes' see-through middles fall","via":"harvest"}}]},"mlok_lug_outer_radius":{"label":"The plate's lugs (two crescents round each hole, on its inner face, that stand in the slot): their outer radius about the hole","kind":"length","measurements":[{"id":"slot","value":0.236,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"({std.mlok.slot_length} - {std.mlok.interval}) / 2","via":"harvest"},"note":"What the slot leaves past each T-nut: two nuts the interval apart in a slot 32 mm long, the lugs about each reaching to the slot's end."},{"id":"photo","value":6.7,"unit":"mm","pm":0.7,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 8a7867bb8d09 (milgear.fi 71642: inside the mount's L, the plate's inner face up, 1400 x 980)","scaleRef":"the plate's two holes, std.mlok.interval (20 mm) apart: 368 px, 18.4 px/mm along the plate's inner face (no camera fitted to this view)","method":"the two crescents about the left hole, outer edge to outer edge along the plate: 246 px","via":"harvest"}}],"adopt":{"from":"slot","reason":"They stand in the slot and can reach no further than its ends; the inside view, read without a fitted camera, agrees within its ±."},"note":"Two crescents about each hole on the plate's inner face (milgear 71642, and the instructions' drawing), standing into the slot."},"mlok_lug_inner_radius":{"label":"The plate's lugs: their inner radius about the hole","kind":"length","measurements":[{"id":"assumed","value":0.157,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the crescents' inner edges stand clear of the hole by about their own width in the inside view (71642), which is too oblique to read it on.","via":"harvest"}}]},"mlok_lug_height":{"label":"The plate's lugs: how far they stand off its inner face into the slot","kind":"length","measurements":[{"id":"assumed","value":0.05,"unit":"in","pm":0.025,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows the lugs in profile; less than a handguard's wall, which they stand in.","via":"harvest"}}]},"mlok_screw_head_height":{"label":"The 10-24 button heads: how far they stand proud of the plate's outer face","kind":"length","measurements":[{"id":"assumed","value":0.05,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the maker's studio picture (GRITR 923578, bcb203eebdd6) shows the domed heads standing out of their counterbores, from three-quarters; their height isn't read.","via":"harvest"}}]},"mlok_edge_break":{"label":"The mount's edges' break (GRITR: \"beveled ends and corners\")","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: GRITR's sentence says the ends and corners are bevelled; their size is in no view at a scale that reads it.","via":"harvest"}}]},"mlok_axis_above_screws":{"label":"On the M-LOK mount on a side face: the light's axis above the plate's screws (the slot's centre line)","kind":"length","measurements":[{"id":"figures","value":1.2,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{.mlok_screw_below_corner} - {.mlok_seat_hole_from_corner} * cos({.mlok_seat_angle}) + ({.axis_above_mount} - {.mlok_lip_height}) * sin({.mlok_seat_angle})","via":"harvest"},"note":"The screws below the plate's top edge, then across the seat to its holes' line and up from the floor by the legs, at the seat's angle."},{"id":"maker-side","value":1.144,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/streamlight-protac-rail-mount-hl-x 83f4380a7ffe (Streamlight's gallery image _5: a handguard from its right side, the HL-X on its M-LOK mount, 800 x 800)","scaleRef":"the handguard's M-LOK slots: 61.2 px to the 40 mm pitch (std.mlok.slot_pitch), 38.9 px/in in the face's plane; the light stands 0.36 in nearer the lens than the face, which a long lens doesn't see","method":"the body's axis (row 274.5: the tube's edges at 257 and 292, 35 px, 0.90 in as the tube is 0.92) to the plate's two screws' middles (row 319): 44.5 px","via":"harvest"}}],"adopt":{"from":"figures","reason":"What the model is drawn from; the maker's view, 2 px under it, stays beside it as the conflict."},"note":"A check of the mount's figures against the maker's own side view of the light on it. The view puts the light 0.06 in lower than the figures do (within the two ±): either the light's legs reach less far below its axis than the 1913 clamp's bolt puts them (axis_above_mount is the bolt's figure: on the clamp nothing shows the legs' feet), or the seat's figures are off within their ± (its thickness and angle move it most). The model draws the figures: the legs stand on the mount's floor as they are drawn on the clamp."},"mlok_axis_out_of_face":{"label":"On the M-LOK mount: the light's axis out from the handguard's face","kind":"length","measurements":[{"id":"figures","value":0.433,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{.mlok_plate_thickness} - {.mlok_seat_hole_from_corner} * sin({.mlok_seat_angle}) - ({.axis_above_mount} - {.mlok_lip_height}) * cos({.mlok_seat_angle})","via":"harvest"}}],"note":"The light stands over the face's top edge leaning out (mlok_seat_angle less 90 degrees): its axis this far out from the face the plate is on, its body 0.46 in round it."},"mlok_mount_weight":{"label":"The M-LOK mount's weight (the aluminium piece alone)","kind":"mass","measurements":[{"id":"metal","value":0.67,"unit":"oz","pm":0.12,"source":{"type":"derived","expr":"{.mlok_length} * ({.mlok_plate_height} * {.mlok_plate_thickness} + {.mlok_seat_width} * {.mlok_seat_thickness} - {.mlok_seat_thickness} * ({.mlok_plate_thickness} + {.mlok_seat_thickness} * cos({.mlok_seat_angle})) / sin({.mlok_seat_angle}) / 2 - {.mlok_plate_thickness} * ({.mlok_seat_thickness} * sin({.mlok_seat_angle}) + ({.mlok_plate_thickness} + {.mlok_seat_thickness} * cos({.mlok_seat_angle})) / sin({.mlok_seat_angle}) * cos({.mlok_seat_angle})) / 2 - ({.mlok_seat_width} - {.mlok_near_lip_width} - {.mlok_far_lip_width}) * {.mlok_lip_height}) * {std.density.aluminium}","via":"harvest"},"note":"Worked out: the section's area (the plate and the seat, less where they overlap at the corner and less the floor between the lips) times the length, times aluminium's density (the alloy isn't named: Battery Junction \"Primary Material Aluminum\", GRITR \"Made from heavy-duty aluminum\"). The holes and lugs aren't taken off or added (about 8% less metal in the model): the ± is that and the section's own."},{"id":"battery-junction","value":36,"unit":"g","pm":0.5,"stated":"Unit Dimensions Weight 1.28 oz (36 g)","source":{"type":"spec","publisher":"retailer","name":"Battery Junction, Streamlight M-LOK Mount for the ProTac Rail Mount Series (88300), Specifications","url":"https://www.batteryjunction.com/products/streamlight-88300","retrieved":"2026-10-19","via":"harvest"},"note":"The package: the same page's \"Shipping Weight 0.08 lb\" is 36 g."}],"adopt":{"from":"metal","reason":"The piece's own metal; the seller's figure is the boxed package's (it equals the page's shipping weight)."},"note":"No maker's figure. Battery Junction's \"Weight 1.28 oz (36 g)\" is the same 36 g its page gives as the shipping weight (\"Shipping Weight 0.08 lb\") and its markup as the variant's weight: the package as boxed (the mount, two 10-24 and two 8-32 screws, two T-nuts, three hex keys), kept beside the figure worked out. The build's weight is the light's published 6.4 oz on either mount (the part has one weight): on the M-LOK mount the light weighs that less its 1913 clamp (no figure published) and more this piece and its four screws and two nuts."}}},{"subject":"superlative-750-gas-block","title":"Superlative Arms .750\" Adjustable Gas Block, Bleed Off - Set Screw, Melonited (SABO-DI-750SM)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"right-to-bear","value":1.68,"unit":"oz","pm":0.005,"stated":"Weight: 1.68 oz.","source":{"type":"spec","publisher":"retailer","name":"Right To Bear, Superlative Arms.750\" Adjustable Gas Block, Bleed Off - Set Screw, Melonited (SABO-DI-750SM), Features","url":"https://www.righttobear.com/superlative-arms-750-adjustable-gas-block-bleed-sabo-di-750sm/","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":1.68,"unit":"oz","pm":0.005,"stated":"Weight 1.68 Oz","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Superlative Arms AR-15 Adjustable Gas Block - Melonite - Set Screw - .750\" (SABO-DI-750SM), Specifications","url":"https://www.primaryarms.com/superlative-arms-bleed-off-adjustable-gas-block-set-screw-750-melonite","retrieved":"2026-10-06","via":"harvest"}},{"id":"dirty-bird","value":1.68,"unit":"oz","pm":0.005,"stated":"Weight: 1.68 oz.","source":{"type":"spec","publisher":"retailer","name":"Dirty Bird Industries, Superlative Arms .750 Adjustable Gas Block - Solid - Melonited - SABO-DI-750SM, Features","url":"https://dirtybirdusa.com/products/superlative-arms-750-adjustable-gas-block-solid-melonited/","retrieved":"2026-10-06","via":"harvest"}},{"id":"blackstone","value":1.68,"unit":"oz","pm":0.005,"stated":"Weight: 1.68 oz","source":{"type":"spec","publisher":"retailer","name":"Blackstone Shooting Sports, Superlative Arms SABO-DI-750SM, Receiver, Solid Adjustable Gas Block, Black Melonite (850011846063)","url":"https://blackstoneshooting.com/superlative-arms-sabo-di-750sm-receiver-solid-adjustable-gas-block-black-melonite-850011846063/","retrieved":"2026-10-06","via":"harvest"}},{"id":"wing","value":1.8,"unit":"oz","pm":0.005,"stated":"Weight : Set Screw Model (.625\"): 1.45 oz. Clamp-On Model (.625\"): 1.45 oz. Set Screw Model (.750\"): 1.80 oz. Clamp-On Model (.750\"): 1.73 oz.","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Superlative Arms Adjustable Gas Block (one page for the .625 and .750, set screw and clamp-on), Specifications","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/gas-systems/gas-blocks/superlative-arms-adjustable-gas-block/","retrieved":"2026-10-06","via":"harvest"}},{"id":"dirty-bird-additional","value":0.768,"unit":"oz","pm":0.0005,"stated":"Weight 0.768 oz","source":{"type":"spec","publisher":"retailer","name":"Dirty Bird Industries, Superlative Arms .750 Adjustable Gas Block - Solid - Melonited - SABO-DI-750SM, Additional information","url":"https://dirtybirdusa.com/products/superlative-arms-750-adjustable-gas-block-solid-melonited/","retrieved":"2026-10-06","via":"harvest"},"note":"Beside 'Dimensions 1 x 0.75 x 0.75 in', which is the journal and the length and not the block: the shop's own shipping fields."}],"adopt":{"from":"right-to-bear","reason":"Four sellers' lists of the maker's features say 1.68 oz for SABO-DI-750SM; Wing Tactical's 1.80 is one table's, and 0.768 is a shop's shipping field. The disagreement stays: nobody says what was weighed."},"note":"No page says what was on the scale (the two set screws, the roll pin). Six sellers repeat 1.68 oz for this number; Wing Tactical's table, the only one that sets the four models side by side, has 1.80 oz for the .750 set screw, and Dirty Bird's 'Additional information' has 0.768 oz beside the 1.68 of its own list. The model's volume as 416 stainless is the check (app/tests/superlative-750-gas-block.test.ts)."},"journal_id":{"label":"Bore (the journal it fits: .750 or .625)","kind":"length","measurements":[{"id":"drawing","value":0.75,"unit":"in","pm":0.0005,"stated":"⌀0.750","source":{"type":"spec","publisher":"retailer","name":"Right To Bear, Superlative Arms.750\" Adjustable Gas Block, Bleed Off - Set Screw, Melonited (SABO-DI-750SM), gallery image 13471: the maker's dimensioned drawing, titled '.750\" ADJUSTABLE GAS BLOCK, SOLID' with the Superlative Arms logo (references/superlative-750-gas-block fcaac37db433)","url":"https://www.righttobear.com/superlative-arms-750-adjustable-gas-block-bleed-sabo-di-750sm/","retrieved":"2026-10-06","via":"harvest"},"note":"The bore's circle, called out across its diameter."},{"id":"right-to-bear","value":0.75,"unit":"in","pm":0.0005,"stated":"Barrel Diameter: 0.750\"","source":{"type":"spec","publisher":"retailer","name":"Right To Bear, Superlative Arms.750\" Adjustable Gas Block, Bleed Off - Set Screw, Melonited (SABO-DI-750SM), Features","url":"https://www.righttobear.com/superlative-arms-750-adjustable-gas-block-bleed-sabo-di-750sm/","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":0.75,"unit":"in","pm":0.0005,"stated":"Gas Seat Diameter .750","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Superlative Arms AR-15 Adjustable Gas Block - Melonite - Set Screw - .750\" (SABO-DI-750SM), Specifications","url":"https://www.primaryarms.com/superlative-arms-bleed-off-adjustable-gas-block-set-screw-750-melonite","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"drawing","reason":"The maker's drawing; two sellers' tables say the same."},"note":"Primary Arms: \"Built for a .750\\\" gas block journal\"; Wing Tactical: \"compatible with any AR-15 and AR-10 barrel that has a .625\\\" or .750\\\" diameter at the gas port area\" (its page is both sizes). The .625 blocks and the clamp-on (SABO-DI-750CM) are other products."},"length":{"label":"Length along the barrel","kind":"length","measurements":[{"id":"right-to-bear","value":1,"unit":"in","pm":0.005,"stated":"Length: 1.00\"","source":{"type":"spec","publisher":"retailer","name":"Right To Bear, Superlative Arms.750\" Adjustable Gas Block, Bleed Off - Set Screw, Melonited (SABO-DI-750SM), Features","url":"https://www.righttobear.com/superlative-arms-750-adjustable-gas-block-bleed-sabo-di-750sm/","retrieved":"2026-10-06","via":"harvest"}},{"id":"blackstone","value":1,"unit":"in","pm":0.005,"stated":"Length: 1.00\"","source":{"type":"spec","publisher":"retailer","name":"Blackstone Shooting Sports, Superlative Arms SABO-DI-750SM, Receiver, Solid Adjustable Gas Block, Black Melonite (850011846063)","url":"https://blackstoneshooting.com/superlative-arms-sabo-di-750sm-receiver-solid-adjustable-gas-block-black-melonite-850011846063/","retrieved":"2026-10-06","via":"harvest"}},{"id":"wing","value":1,"unit":"in","pm":0.5,"stated":"Length : 1\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Superlative Arms Adjustable Gas Block (one page for the .625 and .750, set screw and clamp-on), Specifications","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/gas-systems/gas-blocks/superlative-arms-adjustable-gas-block/","retrieved":"2026-10-06","via":"harvest"}},{"id":"photo-right","value":1.011,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/superlative-750-gas-block 3b5e9fb65021 (Primary Arms' photo of SABO-DI-750SM: its right side straight on, the logo and 'Pat. # US 9,273,916 B1 / Lot # 121416', the adjuster at the right, 2200 x 1466)","scaleRef":"its height, 916.2 px (the boss's top, row 261.7, to the foot's flat, row 1177.9) as height (1.383): 662.5 px/in; the body's length then reads 1.005 to 1.016 in against the sellers' 1.00","method":"the body's rear edge to its front edge, each at the half level: 672.8 px on the foot's rows (1.016 in) and 666.1 px on the boss's rows (1.005); the ± covers the two, the edges' near rims and the scale","via":"harvest"}},{"id":"photo-left","value":1.009,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/superlative-750-gas-block ab5b9b867b45 (Primary Arms' photo of SABO-DI-750SM: its left side straight on, the adjuster and the detent's tab at the left, 2200 x 1467)","scaleRef":"its height, 1009.0 px (the boss's top, row 254.7, to the foot's flat, row 1263.7) as height (1.383): 729.6 px/in; the body's length then reads 1.005 to 1.014 in against the sellers' 1.00","method":"the body's front edge to its rear edge: 739.8 px on the foot's rows (1.014 in) and 733.1 px on the boss's rows (1.005)","via":"harvest"}}],"adopt":{"from":"right-to-bear","reason":"Two sellers' lists state it to the hundredth; both side photos, at the height's scale, read within 1.5% of it."},"note":"The body's, face to face: the adjuster and the detent's tab stand ahead of the front face (adjuster_reach, tab_thickness)."},"height":{"label":"Height, the boss's top to the foot's flat","kind":"length","measurements":[{"id":"drawing","value":1.383,"unit":"in","pm":0.0005,"stated":"1.383","source":{"type":"spec","publisher":"retailer","name":"Right To Bear, Superlative Arms.750\" Adjustable Gas Block, Bleed Off - Set Screw, Melonited (SABO-DI-750SM), gallery image 13471: the maker's dimensioned drawing, titled '.750\" ADJUSTABLE GAS BLOCK, SOLID' with the Superlative Arms logo (references/superlative-750-gas-block fcaac37db433)","url":"https://www.righttobear.com/superlative-arms-750-adjustable-gas-block-bleed-sabo-di-750sm/","retrieved":"2026-10-06","via":"harvest"},"note":"Overall, between the extension lines at the boss's top and the foot's flat."},{"id":"drawing-dirty-bird","value":1.383,"unit":"in","pm":0.0005,"stated":"1.383","source":{"type":"spec","publisher":"retailer","name":"Dirty Bird Industries, Superlative Arms .750 Adjustable Gas Block - Solid - Melonited - SABO-DI-750SM, gallery image _3: the same drawing in another rendering, titled '0.750 ADJUSTABLE BLOCK, SOLID' (references/superlative-750-gas-block 819c65bf85c1; AR15Discounts shows it too, 7daffd4a9f94)","url":"https://dirtybirdusa.com/products/superlative-arms-750-adjustable-gas-block-solid-melonited/","retrieved":"2026-10-06","via":"harvest"}},{"id":"wing","value":1.383,"unit":"in","pm":0.0005,"stated":"Height : Set Screw Model (.625\"): 1.259\" Clamp-On Model (.625\"): 1.303\" Set Screw Model (.750\"): 1.383\" Clamp-On Model (.750\"): 1.426\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Superlative Arms Adjustable Gas Block (one page for the .625 and .750, set screw and clamp-on), Specifications","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/gas-systems/gas-blocks/superlative-arms-adjustable-gas-block/","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":1.383,"unit":"in","pm":0.0005,"stated":"Low profile: 1.383\" height fits under most handguards","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Superlative Arms AR-15 Adjustable Gas Block - Melonite - Set Screw - .750\" (SABO-DI-750SM), Features","url":"https://www.primaryarms.com/superlative-arms-bleed-off-adjustable-gas-block-set-screw-750-melonite","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"drawing","reason":"The maker's own drawing as Right To Bear shows it; Dirty Bird's rendering of it has the same figure."},"note":"Primary Arms: \"Low profile: 1.383\\\" height fits under most handguards\". The drawing's own two halves add to it (0.813 + 0.570)."},"width":{"label":"Width across the ring about the barrel","kind":"length","measurements":[{"id":"drawing","value":0.93,"unit":"in","pm":0.0005,"stated":"0.930","source":{"type":"spec","publisher":"retailer","name":"Right To Bear, Superlative Arms.750\" Adjustable Gas Block, Bleed Off - Set Screw, Melonited (SABO-DI-750SM), gallery image 13471: the maker's dimensioned drawing, titled '.750\" ADJUSTABLE GAS BLOCK, SOLID' with the Superlative Arms logo (references/superlative-750-gas-block fcaac37db433)","url":"https://www.righttobear.com/superlative-arms-750-adjustable-gas-block-bleed-sabo-di-750sm/","retrieved":"2026-10-06","via":"harvest"},"note":"Overall, between extension lines at the ring's two sides, at the bore's height."},{"id":"drawing-dirty-bird","value":0.93,"unit":"in","pm":0.0005,"stated":"0.930","source":{"type":"spec","publisher":"retailer","name":"Dirty Bird Industries, Superlative Arms .750 Adjustable Gas Block - Solid - Melonited - SABO-DI-750SM, gallery image _3: the same drawing in another rendering, titled '0.750 ADJUSTABLE BLOCK, SOLID' (references/superlative-750-gas-block 819c65bf85c1; AR15Discounts shows it too, 7daffd4a9f94)","url":"https://dirtybirdusa.com/products/superlative-arms-750-adjustable-gas-block-solid-melonited/","retrieved":"2026-10-06","via":"harvest"}},{"id":"wing","value":0.93,"unit":"in","pm":0.005,"stated":"Width : 0.625\" Gas Block: 0.78\" 0.750\"Gas Block: 0.93\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Superlative Arms Adjustable Gas Block (one page for the .625 and .750, set screw and clamp-on), Specifications","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/gas-systems/gas-blocks/superlative-arms-adjustable-gas-block/","retrieved":"2026-10-06","via":"harvest"}},{"id":"photo-rear","value":0.9325,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/superlative-750-gas-block 578d3aff1387 (Primary Arms' photo of SABO-DI-750SM: its rear face straight on, the gas tube's hole in the boss, 2200 x 1467)","scaleRef":"its height, 831.0 px (the boss's top to the foot's flat) as height (1.383): 600.9 px/in","method":"the ring's two edges on the row 0.570 in above the flat (columns 828.1 and 1388.4, each at the half level): 560.3 px","via":"harvest"}},{"id":"photo-front","value":0.934,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/superlative-750-gas-block 5689cfe6c588 (Primary Arms' photo of SABO-DI-750SM: its front face straight on, 2200 x 1466)","scaleRef":"its height, 764.8 px (the boss's top, row 389.3, to the foot's flat, row 1154.1) as height (1.383): 553.0 px/in","method":"the ring's two edges on the row 0.570 in above the flat (columns 819.2 and 1335.8): 516.6 px","via":"harvest"}}],"adopt":{"from":"drawing","reason":"The maker's own drawing as Right To Bear shows it; Dirty Bird's rendering of it has the same figure."},"note":"The drawing's extension lines stand 133.5 px either side of the centre line: the ring is 0.465 in to each side. The detent's tab reaches further on the left (tab_corner_z)."},"height_above_bore":{"label":"Top above the bore axis","kind":"length","measurements":[{"id":"drawing","value":0.813,"unit":"in","pm":0.0005,"stated":"0.813","source":{"type":"spec","publisher":"retailer","name":"Right To Bear, Superlative Arms.750\" Adjustable Gas Block, Bleed Off - Set Screw, Melonited (SABO-DI-750SM), gallery image 13471: the maker's dimensioned drawing, titled '.750\" ADJUSTABLE GAS BLOCK, SOLID' with the Superlative Arms logo (references/superlative-750-gas-block fcaac37db433)","url":"https://www.righttobear.com/superlative-arms-750-adjustable-gas-block-bleed-sabo-di-750sm/","retrieved":"2026-10-06","via":"harvest"},"note":"From the bore's horizontal centre line to the boss's top."},{"id":"drawing-dirty-bird","value":0.813,"unit":"in","pm":0.0005,"stated":"0.813","source":{"type":"spec","publisher":"retailer","name":"Dirty Bird Industries, Superlative Arms .750 Adjustable Gas Block - Solid - Melonited - SABO-DI-750SM, gallery image _3: the same drawing in another rendering, titled '0.750 ADJUSTABLE BLOCK, SOLID' (references/superlative-750-gas-block 819c65bf85c1; AR15Discounts shows it too, 7daffd4a9f94)","url":"https://dirtybirdusa.com/products/superlative-arms-750-adjustable-gas-block-solid-melonited/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"drawing","reason":"The maker's own drawing as Right To Bear shows it; Dirty Bird's rendering of it has the same figure."},"note":"The top of the gas tube's boss. Whether a handguard clears it is its inside against this and the tab's corner (tab_corner_z, tab_corner_y: 0.531 in from the bore's axis)."},"foot_below_bore":{"label":"The foot's flat below the bore axis","kind":"length","measurements":[{"id":"drawing","value":0.57,"unit":"in","pm":0.0005,"stated":"0.570","source":{"type":"spec","publisher":"retailer","name":"Right To Bear, Superlative Arms.750\" Adjustable Gas Block, Bleed Off - Set Screw, Melonited (SABO-DI-750SM), gallery image 13471: the maker's dimensioned drawing, titled '.750\" ADJUSTABLE GAS BLOCK, SOLID' with the Superlative Arms logo (references/superlative-750-gas-block fcaac37db433)","url":"https://www.righttobear.com/superlative-arms-750-adjustable-gas-block-bleed-sabo-di-750sm/","retrieved":"2026-10-06","via":"harvest"},"note":"From the bore's horizontal centre line to the foot's flat, where the two set screws are."},{"id":"drawing-dirty-bird","value":0.57,"unit":"in","pm":0.0005,"stated":"0.570","source":{"type":"spec","publisher":"retailer","name":"Dirty Bird Industries, Superlative Arms .750 Adjustable Gas Block - Solid - Melonited - SABO-DI-750SM, gallery image _3: the same drawing in another rendering, titled '0.750 ADJUSTABLE BLOCK, SOLID' (references/superlative-750-gas-block 819c65bf85c1; AR15Discounts shows it too, 7daffd4a9f94)","url":"https://dirtybirdusa.com/products/superlative-arms-750-adjustable-gas-block-solid-melonited/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"drawing","reason":"The maker's own drawing as Right To Bear shows it; Dirty Bird's rendering of it has the same figure."}},"foot_width":{"label":"Width of the foot's flat","kind":"length","measurements":[{"id":"drawing","value":0.383,"unit":"in","pm":0.0005,"stated":"0.383","source":{"type":"spec","publisher":"retailer","name":"Right To Bear, Superlative Arms.750\" Adjustable Gas Block, Bleed Off - Set Screw, Melonited (SABO-DI-750SM), gallery image 13471: the maker's dimensioned drawing, titled '.750\" ADJUSTABLE GAS BLOCK, SOLID' with the Superlative Arms logo (references/superlative-750-gas-block fcaac37db433)","url":"https://www.righttobear.com/superlative-arms-750-adjustable-gas-block-bleed-sabo-di-750sm/","retrieved":"2026-10-06","via":"harvest"},"note":"Between extension lines at the flat's two ends, 54.5 and 55.5 px either side of the centre line."},{"id":"drawing-dirty-bird","value":0.383,"unit":"in","pm":0.0005,"stated":"0.383","source":{"type":"spec","publisher":"retailer","name":"Dirty Bird Industries, Superlative Arms .750 Adjustable Gas Block - Solid - Melonited - SABO-DI-750SM, gallery image _3: the same drawing in another rendering, titled '0.750 ADJUSTABLE BLOCK, SOLID' (references/superlative-750-gas-block 819c65bf85c1; AR15Discounts shows it too, 7daffd4a9f94)","url":"https://dirtybirdusa.com/products/superlative-arms-750-adjustable-gas-block-solid-melonited/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"drawing","reason":"The maker's own drawing as Right To Bear shows it; Dirty Bird's rendering of it has the same figure."}},"boss_width":{"label":"Width of the gas tube's boss on top","kind":"length","measurements":[{"id":"drawing","value":0.351,"unit":"in","pm":0.0005,"stated":"0.351","source":{"type":"spec","publisher":"retailer","name":"Right To Bear, Superlative Arms.750\" Adjustable Gas Block, Bleed Off - Set Screw, Melonited (SABO-DI-750SM), gallery image 13471: the maker's dimensioned drawing, titled '.750\" ADJUSTABLE GAS BLOCK, SOLID' with the Superlative Arms logo (references/superlative-750-gas-block fcaac37db433)","url":"https://www.righttobear.com/superlative-arms-750-adjustable-gas-block-bleed-sabo-di-750sm/","retrieved":"2026-10-06","via":"harvest"},"note":"Between extension lines at the boss's two sides, 50.5 px either side of the centre line."},{"id":"drawing-dirty-bird","value":0.351,"unit":"in","pm":0.0005,"stated":"0.351","source":{"type":"spec","publisher":"retailer","name":"Dirty Bird Industries, Superlative Arms .750 Adjustable Gas Block - Solid - Melonited - SABO-DI-750SM, gallery image _3: the same drawing in another rendering, titled '0.750 ADJUSTABLE BLOCK, SOLID' (references/superlative-750-gas-block 819c65bf85c1; AR15Discounts shows it too, 7daffd4a9f94)","url":"https://dirtybirdusa.com/products/superlative-arms-750-adjustable-gas-block-solid-melonited/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"drawing","reason":"The maker's own drawing as Right To Bear shows it; Dirty Bird's rendering of it has the same figure."},"note":"The boss's top is a half round of this width: the drawing's broken line across it, 0.640 in above the bore, is where the round meets the sides (0.813 less half of 0.351 is 0.6375)."},"tab_corner_z":{"label":"The detent tab's outer corner, left of the bore's vertical centre line","kind":"length","measurements":[{"id":"drawing","value":0.381,"unit":"in","pm":0.0005,"stated":"0.381","source":{"type":"spec","publisher":"retailer","name":"Right To Bear, Superlative Arms.750\" Adjustable Gas Block, Bleed Off - Set Screw, Melonited (SABO-DI-750SM), gallery image 13471: the maker's dimensioned drawing, titled '.750\" ADJUSTABLE GAS BLOCK, SOLID' with the Superlative Arms logo (references/superlative-750-gas-block fcaac37db433)","url":"https://www.righttobear.com/superlative-arms-750-adjustable-gas-block-bleed-sabo-di-750sm/","retrieved":"2026-10-06","via":"harvest"},"note":"From the vertical centre line to an extension line through the cross at the tab's corner (column 484, 110.5 px from the centre line)."},{"id":"drawing-dirty-bird","value":0.381,"unit":"in","pm":0.0005,"stated":"0.381","source":{"type":"spec","publisher":"retailer","name":"Dirty Bird Industries, Superlative Arms .750 Adjustable Gas Block - Solid - Melonited - SABO-DI-750SM, gallery image _3: the same drawing in another rendering, titled '0.750 ADJUSTABLE BLOCK, SOLID' (references/superlative-750-gas-block 819c65bf85c1; AR15Discounts shows it too, 7daffd4a9f94)","url":"https://dirtybirdusa.com/products/superlative-arms-750-adjustable-gas-block-solid-melonited/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"drawing","reason":"The maker's own drawing as Right To Bear shows it; Dirty Bird's rendering of it has the same figure."},"note":"With tab_corner_y it places the one point of the block that stands outside the ring: the upper outer corner of the detent's tab, marked with a cross in the drawing, 0.531 in from the bore's axis (the ring is 0.465). The small circle beside it, the detent's screw, is 0.03 in inside it (detent_screw_z)."},"tab_corner_y":{"label":"The detent tab's outer corner above the bore axis","kind":"length","measurements":[{"id":"drawing","value":0.37,"unit":"in","pm":0.0005,"stated":"0.370","source":{"type":"spec","publisher":"retailer","name":"Right To Bear, Superlative Arms.750\" Adjustable Gas Block, Bleed Off - Set Screw, Melonited (SABO-DI-750SM), gallery image 13471: the maker's dimensioned drawing, titled '.750\" ADJUSTABLE GAS BLOCK, SOLID' with the Superlative Arms logo (references/superlative-750-gas-block fcaac37db433)","url":"https://www.righttobear.com/superlative-arms-750-adjustable-gas-block-bleed-sabo-di-750sm/","retrieved":"2026-10-06","via":"harvest"},"note":"From the bore's horizontal centre line up to an extension line through the same cross (row 269, 106 px above the centre line)."},{"id":"drawing-dirty-bird","value":0.37,"unit":"in","pm":0.0005,"stated":"0.370","source":{"type":"spec","publisher":"retailer","name":"Dirty Bird Industries, Superlative Arms .750 Adjustable Gas Block - Solid - Melonited - SABO-DI-750SM, gallery image _3: the same drawing in another rendering, titled '0.750 ADJUSTABLE BLOCK, SOLID' (references/superlative-750-gas-block 819c65bf85c1; AR15Discounts shows it too, 7daffd4a9f94)","url":"https://dirtybirdusa.com/products/superlative-arms-750-adjustable-gas-block-solid-melonited/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"drawing","reason":"The maker's own drawing as Right To Bear shows it; Dirty Bird's rendering of it has the same figure."}},"adjuster_above_bore":{"label":"The adjustment screw's axis above the bore axis","kind":"length","measurements":[{"id":"drawing-circle","value":0.484,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/superlative-750-gas-block fcaac37db433 (Right To Bear's gallery image 13471: Superlative Arms' drawing '.750\" ADJUSTABLE GAS BLOCK, SOLID', the block seen from its front, 750 x 750)","scaleRef":"the drawing's own callouts, which keep one scale: 287.5 px/in (1.383 over 398 px, 0.930 over 267, 0.383 over 110, 0.351 over 101, 0.381 over 110.5, 0.370 over 106); its bore's circle is 0.749 in at that scale, centred at (373.7, 375.0) on the two centre lines","method":"circles fitted to the strokes of the double circle on the centre line above the bore (the centre line's own pixels left out): the outer, 185 points, centre (374.1, 236.2), radius 23.5 px; the inner, 164 points, centre (373.6, 235.7), radius 21.2 px; 139.0 px above the bore's centre","via":"harvest"}}],"note":"Not called out. The screw is on the bore's vertical centre line (its circles' centres are 0.001 to 0.002 in off it). Both side photos have what stands ahead of the front face at its full reach from 0.42 to 0.56 in above the bore: a middle of 0.49."},"adjuster_d":{"label":"The adjustment screw's end face inside its edge break, diameter","kind":"length","measurements":[{"id":"drawing-circle","value":0.147,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/superlative-750-gas-block fcaac37db433 (Right To Bear's gallery image 13471: Superlative Arms' drawing '.750\" ADJUSTABLE GAS BLOCK, SOLID', the block seen from its front, 750 x 750)","scaleRef":"the drawing's own callouts, which keep one scale: 287.5 px/in (1.383 over 398 px, 0.930 over 267, 0.383 over 110, 0.351 over 101, 0.381 over 110.5, 0.370 over 106); its bore's circle is 0.749 in at that scale, centred at (373.7, 375.0) on the two centre lines","method":"the inner circle of the double circle on the centre line: radius 21.15 px (rms 0.6 px), at its stroke's middle","via":"harvest"}}],"note":"The inner of the drawing's two circles. The screw's head as it stands out of the front face in the two side photos is 0.154 in across (adjuster_head_d): between the drawing's two circles, so the inner one is taken to be the edge of the break round its end face and the outer one the room it turns in."},"adjuster_hole_d":{"label":"The room the adjustment screw turns in, diameter","kind":"length","measurements":[{"id":"drawing-circle","value":0.164,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/superlative-750-gas-block fcaac37db433 (Right To Bear's gallery image 13471: Superlative Arms' drawing '.750\" ADJUSTABLE GAS BLOCK, SOLID', the block seen from its front, 750 x 750)","scaleRef":"the drawing's own callouts, which keep one scale: 287.5 px/in (1.383 over 398 px, 0.930 over 267, 0.383 over 110, 0.351 over 101, 0.381 over 110.5, 0.370 over 106); its bore's circle is 0.749 in at that scale, centred at (373.7, 375.0) on the two centre lines","method":"the outer circle of the double circle on the centre line: radius 23.52 px (rms 0.85 px), at its stroke's middle","via":"harvest"}}],"note":"The outer of the drawing's two circles, taken to be the hole round the screw (the tab is cut to it): nothing says which circle is which."},"adjuster_head_d":{"label":"The adjustment screw's head, diameter","kind":"length","measurements":[{"id":"photo-right","value":0.154,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/superlative-750-gas-block 3b5e9fb65021 (Primary Arms' photo of SABO-DI-750SM: its right side straight on, the logo and 'Pat. # US 9,273,916 B1 / Lot # 121416', the adjuster at the right, 2200 x 1466)","scaleRef":"its height, 916.2 px (the boss's top, row 261.7, to the foot's flat, row 1177.9) as height (1.383): 662.5 px/in; the body's length then reads 1.005 to 1.016 in against the sellers' 1.00","method":"the rows on which the silhouette stands its full 0.217 in ahead of the front face: 426 to 528, 102 px","via":"harvest"}},{"id":"photo-left","value":0.158,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/superlative-750-gas-block ab5b9b867b45 (Primary Arms' photo of SABO-DI-750SM: its left side straight on, the adjuster and the detent's tab at the left, 2200 x 1467)","scaleRef":"its height, 1009.0 px (the boss's top, row 254.7, to the foot's flat, row 1263.7) as height (1.383): 729.6 px/in; the body's length then reads 1.005 to 1.014 in against the sellers' 1.00","method":"the rows on which the silhouette stands its full reach ahead of the front face: 433 to 548, 115 px","via":"harvest"}}],"adopt":{"from":"photo-right","reason":"The two sides agree within their ±; the right one's is taken."},"note":"The screw is in the block's middle plane, where the two side photos' scale is set."},"adjuster_neck_d":{"label":"The adjustment screw's neck between the front face and its head, diameter","kind":"length","measurements":[{"id":"photo-right","value":0.139,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/superlative-750-gas-block 3b5e9fb65021 (Primary Arms' photo of SABO-DI-750SM: its right side straight on, the logo and 'Pat. # US 9,273,916 B1 / Lot # 121416', the adjuster at the right, 2200 x 1466)","scaleRef":"its height, 916.2 px (the boss's top, row 261.7, to the foot's flat, row 1177.9) as height (1.383): 662.5 px/in; the body's length then reads 1.005 to 1.016 in against the sellers' 1.00","method":"the neck's upper edge stands 5 px (0.0075 in) under the head's (5.5 px in the left photo); taken the same underneath, where the tab hides it: the head's 0.154 less twice that","via":"harvest"}}],"note":"Between the face and the head the screw is a little smaller, with a shadow at the step: where the detent bears (Wing Tactical: \"there are 4 clicks/revolution\": four flats, which aren't read)."},"adjuster_neck_length":{"label":"The adjustment screw's neck, from the front face to its head","kind":"length","measurements":[{"id":"photo-right","value":0.074,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/superlative-750-gas-block 3b5e9fb65021 (Primary Arms' photo of SABO-DI-750SM: its right side straight on, the logo and 'Pat. # US 9,273,916 B1 / Lot # 121416', the adjuster at the right, 2200 x 1466)","scaleRef":"its height, 916.2 px (the boss's top, row 261.7, to the foot's flat, row 1177.9) as height (1.383): 662.5 px/in; the body's length then reads 1.005 to 1.016 in against the sellers' 1.00","method":"the step at the head's rear (column 1490) ahead of the front face's edge (column 1441.2): 48.8 px","via":"harvest"}},{"id":"photo-left","value":0.081,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/superlative-750-gas-block ab5b9b867b45 (Primary Arms' photo of SABO-DI-750SM: its left side straight on, the adjuster and the detent's tab at the left, 2200 x 1467)","scaleRef":"its height, 1009.0 px (the boss's top, row 254.7, to the foot's flat, row 1263.7) as height (1.383): 729.6 px/in; the body's length then reads 1.005 to 1.014 in against the sellers' 1.00","method":"the step at the head's rear (column 700) ahead of the front face's edge (column 759): 59 px","via":"harvest"}}],"adopt":{"from":"photo-right","reason":"The two sides agree within their ±; the right one's is taken (as closed, the way it is shipped)."}},"adjuster_reach":{"label":"The adjustment screw's end ahead of the front face","kind":"length","measurements":[{"id":"photo-right","value":0.217,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/superlative-750-gas-block 3b5e9fb65021 (Primary Arms' photo of SABO-DI-750SM: its right side straight on, the logo and 'Pat. # US 9,273,916 B1 / Lot # 121416', the adjuster at the right, 2200 x 1466)","scaleRef":"its height, 916.2 px (the boss's top, row 261.7, to the foot's flat, row 1177.9) as height (1.383): 662.5 px/in; the body's length then reads 1.005 to 1.016 in against the sellers' 1.00","method":"the silhouette's furthest column ahead of the front face's edge (column 1441.2 on the foot's rows) on the rows 0.44 to 0.54 in above the bore: 143.8 px","via":"harvest"}},{"id":"photo-left","value":0.216,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/superlative-750-gas-block ab5b9b867b45 (Primary Arms' photo of SABO-DI-750SM: its left side straight on, the adjuster and the detent's tab at the left, 2200 x 1467)","scaleRef":"its height, 1009.0 px (the boss's top, row 254.7, to the foot's flat, row 1263.7) as height (1.383): 729.6 px/in; the body's length then reads 1.005 to 1.014 in against the sellers' 1.00","method":"the silhouette's furthest column ahead of the front face's edge (column 756.0) on the rows 0.44 to 0.54 in above the bore: 157.6 px","via":"harvest"}}],"adopt":{"from":"photo-right","reason":"The two sides read the same within a thousandth."},"note":"As photographed (Wing Tactical: it \"comes to you with the adjustment screw in the closed position\"); the screw backs out as it is opened, 18 clicks to full pressure and 30 more (\"there are 4 clicks/revolution\"): how far that is isn't published."},"bleed_z":{"label":"The bleed-off port, right of the bore's vertical centre line","kind":"length","measurements":[{"id":"drawing-circle","value":0.119,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/superlative-750-gas-block fcaac37db433 (Right To Bear's gallery image 13471: Superlative Arms' drawing '.750\" ADJUSTABLE GAS BLOCK, SOLID', the block seen from its front, 750 x 750)","scaleRef":"the drawing's own callouts, which keep one scale: 287.5 px/in (1.383 over 398 px, 0.930 over 267, 0.383 over 110, 0.351 over 101, 0.381 over 110.5, 0.370 over 106); its bore's circle is 0.749 in at that scale, centred at (373.7, 375.0) on the two centre lines","method":"a circle fitted to the stroke of the plain circle left of the adjuster's (its part clear of the adjuster's circle, 212 points): centre (339.3, 241.7), radius 16.7 px; 34.4 px from the bore's centre line","via":"harvest"}}],"note":"The plain circle beside the adjuster in the drawing, on the side away from the tab: the part's right, since the drawing is seen from the front (the adjuster, the port and the tab are on the front face: Right To Bear, \"Bleed Off Port: (Patent Pending) Front Of Block\"). Primary Arms' front photo has a dark hole there."},"bleed_above_bore":{"label":"The bleed-off port above the bore axis","kind":"length","measurements":[{"id":"drawing-circle","value":0.463,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/superlative-750-gas-block fcaac37db433 (Right To Bear's gallery image 13471: Superlative Arms' drawing '.750\" ADJUSTABLE GAS BLOCK, SOLID', the block seen from its front, 750 x 750)","scaleRef":"the drawing's own callouts, which keep one scale: 287.5 px/in (1.383 over 398 px, 0.930 over 267, 0.383 over 110, 0.351 over 101, 0.381 over 110.5, 0.370 over 106); its bore's circle is 0.749 in at that scale, centred at (373.7, 375.0) on the two centre lines","method":"the same circle: its centre 133.3 px above the bore's","via":"harvest"}}]},"bleed_d":{"label":"The bleed-off port, diameter","kind":"length","measurements":[{"id":"drawing-circle","value":0.116,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/superlative-750-gas-block fcaac37db433 (Right To Bear's gallery image 13471: Superlative Arms' drawing '.750\" ADJUSTABLE GAS BLOCK, SOLID', the block seen from its front, 750 x 750)","scaleRef":"the drawing's own callouts, which keep one scale: 287.5 px/in (1.383 over 398 px, 0.930 over 267, 0.383 over 110, 0.351 over 101, 0.381 over 110.5, 0.370 over 106); its bore's circle is 0.749 in at that scale, centred at (373.7, 375.0) on the two centre lines","method":"the same circle: radius 16.67 px (rms 0.9 px), at its stroke's middle","via":"harvest"}}]},"tab_top_above_bore":{"label":"The detent tab's upper edge above the bore axis","kind":"length","measurements":[{"id":"drawing-line","value":0.485,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/superlative-750-gas-block fcaac37db433 (Right To Bear's gallery image 13471: Superlative Arms' drawing '.750\" ADJUSTABLE GAS BLOCK, SOLID', the block seen from its front, 750 x 750)","scaleRef":"the drawing's own callouts, which keep one scale: 287.5 px/in (1.383 over 398 px, 0.930 over 267, 0.383 over 110, 0.351 over 101, 0.381 over 110.5, 0.370 over 106); its bore's circle is 0.749 in at that scale, centred at (373.7, 375.0) on the two centre lines","method":"the level stroke from the adjuster's circle (column 398) to the outline (column 431): row 235.5, 139.5 px above the bore's centre","via":"harvest"}},{"id":"photo-left","value":0.491,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/superlative-750-gas-block ab5b9b867b45 (Primary Arms' photo of SABO-DI-750SM: its left side straight on, the adjuster and the detent's tab at the left, 2200 x 1467)","scaleRef":"its height, 1009.0 px (the boss's top, row 254.7, to the foot's flat, row 1263.7) as height (1.383): 729.6 px/in; the body's length then reads 1.005 to 1.014 in against the sellers' 1.00","method":"the upper edge of the block that stands ahead of the front face under the adjuster (row 489.6 in the photo): 234.9 px below the boss's top","via":"harvest"}}],"adopt":{"from":"drawing-line","reason":"The drawing's line; the left side photo has the tab's upper edge there within its ±."},"note":"The level line from the adjuster's circle to the outline in the drawing: the tab's upper edge, at the adjuster's own height."},"pin_hole_from_front":{"label":"The gas tube's roll pin: its cross hole behind the front face","kind":"length","measurements":[{"id":"photo-right","value":0.311,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/superlative-750-gas-block 3b5e9fb65021 (Primary Arms' photo of SABO-DI-750SM: its right side straight on, the logo and 'Pat. # US 9,273,916 B1 / Lot # 121416', the adjuster at the right, 2200 x 1466)","scaleRef":"its height, 916.2 px (the boss's top, row 261.7, to the foot's flat, row 1177.9) as height (1.383): 662.5 px/in; the body's length then reads 1.005 to 1.016 in against the sellers' 1.00","method":"the hole's rim picked on an 8x gridded crop (columns 1204.4 to 1258.1, rows 329.4 to 390: centre (1231.5, 359.4)) behind the front face's edge on the boss's rows (column 1437.2): 205.7 px","via":"harvest"}},{"id":"photo-left","value":0.315,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/superlative-750-gas-block ab5b9b867b45 (Primary Arms' photo of SABO-DI-750SM: its left side straight on, the adjuster and the detent's tab at the left, 2200 x 1467)","scaleRef":"its height, 1009.0 px (the boss's top, row 254.7, to the foot's flat, row 1263.7) as height (1.383): 729.6 px/in; the body's length then reads 1.005 to 1.014 in against the sellers' 1.00","method":"the hole's rim picked on an 8x gridded crop (columns 965 to 1018.8, rows 330.6 to 390: centre (991.9, 360.3)) behind the front face's edge on the boss's rows (column 761.8): 230.1 px","via":"harvest"}}],"adopt":{"from":"photo-right","reason":"The two sides agree within their ±; the right one's is taken."},"note":"Through the boss from side to side, seen in both side photos. With the sellers' length it is 0.687 in ahead of the rear face: the Army's front sight has it .688 from its rear face (drawing 8448566, by the BCM block's ledger)."},"pin_hole_d":{"label":"The gas tube's roll pin: its cross hole, diameter","kind":"length","measurements":[{"id":"tdp","value":0.078,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{bcm-750-gas-block.pin_hole_d}"},"note":"The Army's hole for the gas tube's pin (drawing 8448566, as the BCM block's ledger cites it): the Army's sight, not this block."},{"id":"photo-right","value":0.081,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/superlative-750-gas-block 3b5e9fb65021 (Primary Arms' photo of SABO-DI-750SM: its right side straight on, the logo and 'Pat. # US 9,273,916 B1 / Lot # 121416', the adjuster at the right, 2200 x 1466)","scaleRef":"its height, 916.2 px (the boss's top, row 261.7, to the foot's flat, row 1177.9) as height (1.383): 662.5 px/in; the body's length then reads 1.005 to 1.016 in against the sellers' 1.00","method":"the hole's rim on the 8x crop: 53.7 px across, its edge break included","via":"harvest"}},{"id":"photo-left","value":0.074,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/superlative-750-gas-block ab5b9b867b45 (Primary Arms' photo of SABO-DI-750SM: its left side straight on, the adjuster and the detent's tab at the left, 2200 x 1467)","scaleRef":"its height, 1009.0 px (the boss's top, row 254.7, to the foot's flat, row 1263.7) as height (1.383): 729.6 px/in; the body's length then reads 1.005 to 1.014 in against the sellers' 1.00","method":"the hole's rim on the 8x crop: 53.8 px across","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The pin it takes is the standard one; the two photos read either side of it, within their ±."},"note":"The block takes the standard tube and its pin (the pin is in the box: Right To Bear, \"1x Gas Tube Roll Pins\"; \"***Gas Tube NOT Included***\")."},"pin_to_port":{"label":"The gas tube's pin hole to its gas hole","kind":"length","measurements":[{"id":"tdp","value":0.418,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{bcm-750-gas-block.pin_to_port}"},"note":"The Army's gas tube (drawing 8448567, as the BCM block's ledger cites it): the tube this block takes."}]},"port_from_rear":{"label":"Its gas port ahead of its rear face","kind":"length","measurements":[{"id":"derived","value":0.271,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{superlative-750-gas-block.length} - {superlative-750-gas-block.pin_hole_from_front} - {superlative-750-gas-block.pin_to_port}"}}],"note":"Not published, and the port is inside. Where the standard tube's gas hole lands with its pin in the block's cross hole: the length less the pin's place behind the front face less the tube's pin-to-port. The Army's own sight has its port .270 from its rear face. The part's frame is here."},"tube_hole_above_bore":{"label":"The gas tube's hole, its axis above the bore (at the block)","kind":"length","measurements":[{"id":"photo-rear","value":0.685,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/superlative-750-gas-block 578d3aff1387 (Primary Arms' photo of SABO-DI-750SM: its rear face straight on, the gas tube's hole in the boss, 2200 x 1467)","scaleRef":"its height, 831.0 px (the boss's top, row 277.1, to the foot's flat, row 1108.0) as height (1.383): 600.9 px/in; its width then reads 0.9325 in (the drawing's 0.930) and the bore, seen through, 0.751 (.750): three published sizes within 0.3%","method":"a circle through the hole's edge on 60 rays from its middle, each at the half level between the hole (11 of 255) and the face (49): centre (1105.2, 353.7), radius 56.0 px (rms 1.2); 0.128 in below the boss's top, 411.8 px above the row 0.570 in over the flat; 0.005 in off the middle column","via":"harvest"}}],"note":"Not published. The hole stands high in its boss (0.035 in of wall above it, 0.08 beside it): 0.060 in above the Army's .625 for a front sight, which the BCM and Aero blocks are drawn at. No page says which gas tube it wants (Right To Bear: \"***Gas Tube NOT Included***\"); an aggregator's line about tube offsets was not taken."},"tube_hole_d":{"label":"The gas tube's hole, diameter","kind":"length","measurements":[{"id":"tdp","value":0.1805,"unit":"in","pm":0.001,"source":{"type":"derived","expr":"{bcm-750-gas-block.tube_hole_d}"},"note":"The Army's hole for the .180 tube (drawing 8448566, as the BCM block's ledger cites it): the Army's sight, not this block."},{"id":"photo-rear","value":0.186,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/superlative-750-gas-block 578d3aff1387 (Primary Arms' photo of SABO-DI-750SM: its rear face straight on, the gas tube's hole in the boss, 2200 x 1467)","scaleRef":"its height, 831.0 px (the boss's top, row 277.1, to the foot's flat, row 1108.0) as height (1.383): 600.9 px/in; its width then reads 0.9325 in (the drawing's 0.930) and the bore, seen through, 0.751 (.750): three published sizes within 0.3%","method":"the same circle: 112.0 px across at the half level, its edge break included","via":"harvest"}}],"adopt":{"from":"tdp","reason":"It takes the standard tube; the rear photo's hole, with its edge break, is 0.006 in over."}},"tube_hole_past_pin":{"label":"How far the gas tube's hole runs on ahead of the pin's hole","kind":"length","measurements":[{"id":"tdp","value":0.217,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{bcm-750-gas-block.tube_hole_past_pin}"},"note":"The Army's sight (drawing 8448566, as the BCM block's ledger cites it), not this block."}],"note":"Not published and not seen: the hole enters the rear face and the boss's front is closed in every photo of it. The Army's sight's depth is taken."},"detent_pin_z":{"label":"The detent's pin, its axis left of the bore's vertical centre line","kind":"length","measurements":[{"id":"drawing-circle","value":0.342,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/superlative-750-gas-block fcaac37db433 (Right To Bear's gallery image 13471: Superlative Arms' drawing '.750\" ADJUSTABLE GAS BLOCK, SOLID', the block seen from its front, 750 x 750)","scaleRef":"the drawing's own callouts, which keep one scale: 287.5 px/in (1.383 over 398 px, 0.930 over 267, 0.383 over 110, 0.351 over 101, 0.381 over 110.5, 0.370 over 106); its bore's circle is 0.749 in at that scale, centred at (373.7, 375.0) on the two centre lines","method":"a circle fitted to the stroke of the small circle on the tab's ear (108 points): centre (471.9, 281.8), radius 9.2 px; 98.2 px from the bore's centre line","via":"harvest"}}],"note":"The small circle on the tab's ear in the drawing: the front end of the pin that runs back through the tab and the pad and lies in a groove along the left side (the patent's pin 70). Primary Arms' front photo shows a small bright ring there. It is 0.471 in from the bore's axis: 0.006 outside the ring's surface, so behind the pad the pin lies half sunk in it."},"detent_pin_above_bore":{"label":"The detent's pin, its axis above the bore axis","kind":"length","measurements":[{"id":"drawing-circle","value":0.324,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/superlative-750-gas-block fcaac37db433 (Right To Bear's gallery image 13471: Superlative Arms' drawing '.750\" ADJUSTABLE GAS BLOCK, SOLID', the block seen from its front, 750 x 750)","scaleRef":"the drawing's own callouts, which keep one scale: 287.5 px/in (1.383 over 398 px, 0.930 over 267, 0.383 over 110, 0.351 over 101, 0.381 over 110.5, 0.370 over 106); its bore's circle is 0.749 in at that scale, centred at (373.7, 375.0) on the two centre lines","method":"the same circle: its centre 93.2 px above the bore's","via":"harvest"}},{"id":"photo-left","value":0.259,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/superlative-750-gas-block ab5b9b867b45 (Primary Arms' photo of SABO-DI-750SM: its left side straight on, the adjuster and the detent's tab at the left, 2200 x 1467)","scaleRef":"its height, 1009.0 px (the boss's top, row 254.7, to the foot's flat, row 1263.7) as height (1.383): 729.6 px/in; the body's length then reads 1.005 to 1.014 in against the sellers' 1.00","method":"the rod's two edges where it lies in its groove behind the pad (rows 640 and 678.5): its middle 404.5 px below the boss's top. As read: the rod is on the side near the lens, 0.34 in out from the middle plane, and the photo is from above","via":"harvest"}}],"adopt":{"from":"drawing-circle","reason":"The maker's drawing, square on. The side photo is from above and reads what is near the lens low: 0.065 in here, 0.34 in out from the middle plane."},"note":"Both side photos are taken from close by and from a little above: the pin's hole shows its far wall above its near rim, the tab reads 0.182 in thick where it is near the lens (the left photo) and 0.151 where it is far (the right), and what is on the near side reads low (the detent's pin 0.065 in under the drawing's circle for it). Lengths along the block at the middle plane are as read; heights of anything off that plane are not."},"detent_pin_d":{"label":"The detent's pin, diameter","kind":"length","measurements":[{"id":"drawing-circle","value":0.064,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/superlative-750-gas-block fcaac37db433 (Right To Bear's gallery image 13471: Superlative Arms' drawing '.750\" ADJUSTABLE GAS BLOCK, SOLID', the block seen from its front, 750 x 750)","scaleRef":"the drawing's own callouts, which keep one scale: 287.5 px/in (1.383 over 398 px, 0.930 over 267, 0.383 over 110, 0.351 over 101, 0.381 over 110.5, 0.370 over 106); its bore's circle is 0.749 in at that scale, centred at (373.7, 375.0) on the two centre lines","method":"the same circle: radius 9.24 px (rms 0.7 px), at its stroke's middle","via":"harvest"}},{"id":"photo-left","value":0.053,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/superlative-750-gas-block ab5b9b867b45 (Primary Arms' photo of SABO-DI-750SM: its left side straight on, the adjuster and the detent's tab at the left, 2200 x 1467)","scaleRef":"its height, 1009.0 px (the boss's top, row 254.7, to the foot's flat, row 1263.7) as height (1.383): 729.6 px/in; the body's length then reads 1.005 to 1.014 in against the sellers' 1.00","method":"the rod's two edges in its groove (rows 640 and 678.5): 38.5 px, what of it stands out of the groove","via":"harvest"}}],"adopt":{"from":"drawing-circle","reason":"Its end as the maker draws it; the side photo sees what stands out of its groove."}},"detent_pin_rear":{"label":"The detent's pin, its rear end behind the front face","kind":"length","measurements":[{"id":"photo-left","value":0.402,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/superlative-750-gas-block ab5b9b867b45 (Primary Arms' photo of SABO-DI-750SM: its left side straight on, the adjuster and the detent's tab at the left, 2200 x 1467)","scaleRef":"its height, 1009.0 px (the boss's top, row 254.7, to the foot's flat, row 1263.7) as height (1.383): 729.6 px/in; the body's length then reads 1.005 to 1.014 in against the sellers' 1.00","method":"the rod's rounded rear end (column 1052.5) behind the front face's edge (column 759): 293.5 px; the ± covers the lens's nearness (what is near it reads some 5% long)","via":"harvest"}}]},"tab_thickness":{"label":"The detent tab, how far it stands ahead of the front face","kind":"length","measurements":[{"id":"photo-left","value":0.182,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/superlative-750-gas-block ab5b9b867b45 (Primary Arms' photo of SABO-DI-750SM: its left side straight on, the adjuster and the detent's tab at the left, 2200 x 1467)","scaleRef":"its height, 1009.0 px (the boss's top, row 254.7, to the foot's flat, row 1263.7) as height (1.383): 729.6 px/in; the body's length then reads 1.005 to 1.014 in against the sellers' 1.00","method":"the silhouette's furthest column ahead of the front face's edge on the rows of the tab's ear: 0.177 to 0.185 in (129 to 135 px); the ear is 0.36 in nearer the lens than the middle plane","via":"harvest"}},{"id":"photo-right","value":0.151,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/superlative-750-gas-block 3b5e9fb65021 (Primary Arms' photo of SABO-DI-750SM: its right side straight on, the logo and 'Pat. # US 9,273,916 B1 / Lot # 121416', the adjuster at the right, 2200 x 1466)","scaleRef":"its height, 916.2 px (the boss's top, row 261.7, to the foot's flat, row 1177.9) as height (1.383): 662.5 px/in; the body's length then reads 1.005 to 1.016 in against the sellers' 1.00","method":"the silhouette's furthest column ahead of the front face's edge on the rows under the adjuster: 0.143 to 0.151 in (95 to 100 px); the tab is 0.36 in beyond the middle plane","via":"harvest"}}],"adopt":{"value":0.166,"unit":"in","pm":0.012,"reason":"Neither reading: the same block read 0.182 where it is 0.36 in nearer the lens than the middle plane and 0.151 where it is 0.36 in beyond it. Their ratio puts the lens 3.9 in from the middle plane, and each reading taken back to that plane is 0.165 (0.182 x 3.54 / 3.9, 0.151 x 4.26 / 3.9); the geometric mean of the two is 0.166."},"note":"The tab is a block on the front face, not a plate. Both side photos are taken from close by and from a little above: the pin's hole shows its far wall above its near rim, the tab reads 0.182 in thick where it is near the lens (the left photo) and 0.151 where it is far (the right), and what is on the near side reads low (the detent's pin 0.065 in under the drawing's circle for it). Lengths along the block at the middle plane are as read; heights of anything off that plane are not. The two readings are one block seen near and far: a lens some 4 in off makes them 0.167 and 0.164."},"pad_length":{"label":"The raised pad on the left side behind the front face, its length","kind":"length","measurements":[{"id":"photo-left","value":0.218,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/superlative-750-gas-block ab5b9b867b45 (Primary Arms' photo of SABO-DI-750SM: its left side straight on, the adjuster and the detent's tab at the left, 2200 x 1467)","scaleRef":"its height, 1009.0 px (the boss's top, row 254.7, to the foot's flat, row 1263.7) as height (1.383): 729.6 px/in; the body's length then reads 1.005 to 1.014 in against the sellers' 1.00","method":"the step's edge (column 918, lit along its length) behind the front face's edge (column 759): 159 px; the ± covers the lens's nearness (what is near it reads some 5% long)","via":"harvest"}}],"note":"A band of the left side stands proud from the front face back to a step: what makes the bulge beside the tab in the drawing's outline, and what the pin's hole is in. The model takes its section from the drawing."},"tab_window_d":{"label":"The window across the tab's ear, diameter","kind":"length","measurements":[{"id":"photo-left","value":0.115,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/superlative-750-gas-block ab5b9b867b45 (Primary Arms' photo of SABO-DI-750SM: its left side straight on, the adjuster and the detent's tab at the left, 2200 x 1467)","scaleRef":"its height, 1009.0 px (the boss's top, row 254.7, to the foot's flat, row 1263.7) as height (1.383): 729.6 px/in; the body's length then reads 1.005 to 1.014 in against the sellers' 1.00","method":"the window's width (columns 684 to 767.5: 83.5 px); its height reads the same (rows 617.5 to 702.5)","via":"harvest"}}],"note":"A hole across the tab's ear through which the pin shows, bright, in the left side photo and in Wing Tactical's stainless one (a80edfa7809c). Its height is the pin's."},"tab_window_ahead":{"label":"The window across the tab's ear, its middle ahead of the front face","kind":"length","measurements":[{"id":"photo-left","value":0.045,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/superlative-750-gas-block ab5b9b867b45 (Primary Arms' photo of SABO-DI-750SM: its left side straight on, the adjuster and the detent's tab at the left, 2200 x 1467)","scaleRef":"its height, 1009.0 px (the boss's top, row 254.7, to the foot's flat, row 1263.7) as height (1.383): 729.6 px/in; the body's length then reads 1.005 to 1.014 in against the sellers' 1.00","method":"the window's middle (column 725.8) ahead of the front face's edge (column 759): 33 px","via":"harvest"}}]},"pin_hole_above_bore":{"label":"The gas tube's roll pin: its cross hole above the bore axis","kind":"length","measurements":[{"id":"tube-axis","value":0.685,"unit":"in","pm":0.008,"source":{"type":"derived","expr":"{superlative-750-gas-block.tube_hole_above_bore}"},"note":"The tube's own axis, by the rear photo."},{"id":"photo-right","value":0.666,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/superlative-750-gas-block 3b5e9fb65021 (Primary Arms' photo of SABO-DI-750SM: its right side straight on, the logo and 'Pat. # US 9,273,916 B1 / Lot # 121416', the adjuster at the right, 2200 x 1466)","scaleRef":"its height, 916.2 px (the boss's top, row 261.7, to the foot's flat, row 1177.9) as height (1.383): 662.5 px/in; the body's length then reads 1.005 to 1.016 in against the sellers' 1.00","method":"the hole's rim's centre (row 359.4) below the boss's top (row 261.7): 97.7 px, 0.1475 in below the 0.813 of the top. As read, from above","via":"harvest"}},{"id":"photo-left","value":0.668,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/superlative-750-gas-block ab5b9b867b45 (Primary Arms' photo of SABO-DI-750SM: its left side straight on, the adjuster and the detent's tab at the left, 2200 x 1467)","scaleRef":"its height, 1009.0 px (the boss's top, row 254.7, to the foot's flat, row 1263.7) as height (1.383): 729.6 px/in; the body's length then reads 1.005 to 1.014 in against the sellers' 1.00","method":"the hole's rim's centre (row 360.3) below the boss's top (row 254.7): 105.6 px, 0.1447 in below the 0.813 of the top. As read, from above","via":"harvest"}}],"adopt":{"from":"tube-axis","reason":"The pin crosses the tube. Both side photos read 0.018 in lower, on a rim 0.18 in nearer the lens than the middle plane, in photos taken from above."},"note":"A pin through the tube crosses its axis: the hole is at the tube's height. Both side photos are taken from close by and from a little above: the pin's hole shows its far wall above its near rim, the tab reads 0.182 in thick where it is near the lens (the left photo) and 0.151 where it is far (the right), and what is on the near side reads low (the detent's pin 0.065 in under the drawing's circle for it). Lengths along the block at the middle plane are as read; heights of anything off that plane are not. The hole's near rim is 0.18 in out from the middle plane and reads 0.018 low."},"scoop_from_front":{"label":"The round pocket low on the left side: its middle behind the front face","kind":"length","measurements":[{"id":"photo-left","value":0.508,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/superlative-750-gas-block ab5b9b867b45 (Primary Arms' photo of SABO-DI-750SM: its left side straight on, the adjuster and the detent's tab at the left, 2200 x 1467)","scaleRef":"its height, 1009.0 px (the boss's top, row 254.7, to the foot's flat, row 1263.7) as height (1.383): 729.6 px/in; the body's length then reads 1.005 to 1.014 in against the sellers' 1.00","method":"the pocket's two sides (columns 1074 and 1180) on a 5x gridded crop: its middle, column 1127, behind the front face's edge on the foot's rows (column 756.0): 371 px","via":"harvest"}}],"note":"A flat-floored round pocket in the left side's lower flank, at mid length, seen as a D with its flat down: its floor meets the flank's surface along that flat. What it is for isn't said anywhere; Primary Arms' right side photo shows none on the right."},"scoop_d":{"label":"The round pocket low on the left side: diameter","kind":"length","measurements":[{"id":"photo-left","value":0.145,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/superlative-750-gas-block ab5b9b867b45 (Primary Arms' photo of SABO-DI-750SM: its left side straight on, the adjuster and the detent's tab at the left, 2200 x 1467)","scaleRef":"its height, 1009.0 px (the boss's top, row 254.7, to the foot's flat, row 1263.7) as height (1.383): 729.6 px/in; the body's length then reads 1.005 to 1.014 in against the sellers' 1.00","method":"the pocket's two sides (columns 1074 and 1180): 106 px; the ± covers the lens's nearness","via":"harvest"}}]},"scoop_top_below_bore":{"label":"The round pocket low on the left side: its top below the bore axis","kind":"length","measurements":[{"id":"photo-left","value":0.271,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/superlative-750-gas-block ab5b9b867b45 (Primary Arms' photo of SABO-DI-750SM: its left side straight on, the adjuster and the detent's tab at the left, 2200 x 1467)","scaleRef":"its height, 1009.0 px (the boss's top, row 254.7, to the foot's flat, row 1263.7) as height (1.383): 729.6 px/in; the body's length then reads 1.005 to 1.014 in against the sellers' 1.00","method":"the top of its arc (row 1079): 824.3 px below the boss's top, 1.130 in, less the 0.813 of the top: 0.317 as read. The photo is from above and reads what is near the lens low, by 0.19 in for each inch out from the middle plane at the detent's pin (0.259 read where the drawing has 0.324, 0.34 in out) and by 0.10 at the roll pin's hole (0.668 where the tube's axis is 0.685, 0.18 in out): 0.14 is taken, and the ± covers the two: the arc's top is on the flank 0.33 in out, 0.046 in less","via":"harvest"}}]},"scoop_flat_below_bore":{"label":"The round pocket low on the left side: its flat lower edge below the bore axis","kind":"length","measurements":[{"id":"photo-left","value":0.359,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/superlative-750-gas-block ab5b9b867b45 (Primary Arms' photo of SABO-DI-750SM: its left side straight on, the adjuster and the detent's tab at the left, 2200 x 1467)","scaleRef":"its height, 1009.0 px (the boss's top, row 254.7, to the foot's flat, row 1263.7) as height (1.383): 729.6 px/in; the body's length then reads 1.005 to 1.014 in against the sellers' 1.00","method":"its straight lower edge (row 1140): 885.3 px below the boss's top, 1.213 in, less the 0.813 of the top: 0.400 as read. The photo is from above and reads what is near the lens low, by 0.19 in for each inch out from the middle plane at the detent's pin (0.259 read where the drawing has 0.324, 0.34 in out) and by 0.10 at the roll pin's hole (0.668 where the tube's axis is 0.685, 0.18 in out): 0.14 is taken, and the ± covers the two: the edge is on the flank 0.29 in out, 0.041 in less","via":"harvest"}}]},"set_screw_rear":{"label":"The rear set screw, ahead of the rear face","kind":"length","measurements":[{"id":"photo-wing","value":0.26,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/superlative-750-gas-block 31f0f5230294 (Wing Tactical's gallery image 66646: a stainless set-screw block lying on its right side, its underside's flat toward the lens with both screws, 'Lot # 100417', 1280 x 1280; the page is for the .625 and the .750 and the picture doesn't say which it is)","scaleRef":"the flat's own length along its middle line, 1228.5 px (3x crop) between its rear and front edges, as length (1.00): the middle line through both screws meets each end edge at its middle (0.52 and 0.53 of the way across)","method":"the rear screw's middle 312 px along the flat's middle line from the rear edge (0.254 of it); the front screw's socket is 4% larger in the picture than the rear's, and with the scale growing by that along the flat it is 0.26; the ± covers the picked corners and that","via":"harvest"}}],"note":"Two socket set screws in the foot's flat, in line along its middle (Right To Bear: \"2x 10-32 x 3/16\\\" Socket Head Cap Screws\"; Dirty Bird: \"Two 10-32 x 3/16″ set screws\"; Joe Bob's: \"(2) 10-32 x 1/4\\\" Set Screws\"). No view square to the underside is on file: read off an oblique one of a stainless block whose diameter the page doesn't say."},"set_screw_front":{"label":"The front set screw, ahead of the rear face","kind":"length","measurements":[{"id":"photo-wing","value":0.73,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/superlative-750-gas-block 31f0f5230294 (Wing Tactical's gallery image 66646: a stainless set-screw block lying on its right side, its underside's flat toward the lens with both screws, 'Lot # 100417', 1280 x 1280; the page is for the .625 and the .750 and the picture doesn't say which it is)","scaleRef":"the flat's own length along its middle line, 1228.5 px (3x crop) between its rear and front edges, as length (1.00): the middle line through both screws meets each end edge at its middle (0.52 and 0.53 of the way across)","method":"the front screw's middle 890 px along the flat's middle line from the rear edge (0.724 of it); 0.73 with the picture's perspective taken out the same way","via":"harvest"}}]},"set_screw_d":{"label":"A set screw, diameter as it shows in the flat","kind":"length","measurements":[{"id":"photo-wing","value":0.185,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/superlative-750-gas-block 31f0f5230294 (Wing Tactical's gallery image 66646: a stainless set-screw block lying on its right side, its underside's flat toward the lens with both screws, 'Lot # 100417', 1280 x 1280; the page is for the .625 and the .750 and the picture doesn't say which it is)","scaleRef":"the flat's width across the same picture, 480 px (3x crop) between its two long edges at the rear screw, as foot_width (0.383)","method":"the rear screw's bright ring, 230 px across along the flat's width","via":"harvest"}}],"note":"The sellers call the thread 10-32; the figure here is the screw's bright end as photographed, against the flat it is in."},"hex_key":{"label":"The hex key in the box, across flats","kind":"length","measurements":[{"id":"right-to-bear","value":0.09375,"unit":"in","pm":0.0005,"stated":"1x 3/32 X 6\" L-Shaped Hex Keys","source":{"type":"spec","publisher":"retailer","name":"Right To Bear, Superlative Arms.750\" Adjustable Gas Block, Bleed Off - Set Screw, Melonited (SABO-DI-750SM), Features","url":"https://www.righttobear.com/superlative-arms-750-adjustable-gas-block-bleed-sabo-di-750sm/","retrieved":"2026-10-06","via":"harvest"}},{"id":"wing","value":0.09375,"unit":"in","pm":0.0005,"stated":"1x 3/32 x 6\" L-shaped Hex key","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Superlative Arms Adjustable Gas Block (one page for the .625 and .750, set screw and clamp-on), Specifications","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/gas-systems/gas-blocks/superlative-arms-adjustable-gas-block/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"right-to-bear","reason":"Two sellers list the same key."},"note":"Wing Tactical: \"you will adjust the piston gas block utilizing the 3/32” Allen wrench provided\": the adjuster's socket. The set screws' sockets are drawn at the same size (one key is in the box); no page says so."},"set_screw_length":{"label":"A set screw, length","kind":"length","measurements":[{"id":"right-to-bear","value":0.1875,"unit":"in","pm":0.0005,"stated":"2x 10-32 x 3/16\" Socket Head Cap Screws","source":{"type":"spec","publisher":"retailer","name":"Right To Bear, Superlative Arms.750\" Adjustable Gas Block, Bleed Off - Set Screw, Melonited (SABO-DI-750SM), Features","url":"https://www.righttobear.com/superlative-arms-750-adjustable-gas-block-bleed-sabo-di-750sm/","retrieved":"2026-10-06","via":"harvest"}},{"id":"wing","value":0.1875,"unit":"in","pm":0.0005,"stated":"2x 10-32 x 3/16\"socket head cap screws","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, Superlative Arms Adjustable Gas Block (one page for the .625 and .750, set screw and clamp-on), Specifications","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/gas-systems/gas-blocks/superlative-arms-adjustable-gas-block/","retrieved":"2026-10-06","via":"harvest"}},{"id":"mounts-plus","value":0.1875,"unit":"in","pm":0.0005,"stated":"(2) 10-32 x 3/16\" Set Screws","source":{"type":"spec","publisher":"retailer","name":"Mounts Plus, Superlative Arms Adjustable Gas Block .750\", Bleed Off Solid","url":"https://www.mountsplus.com/superlative-arms-adjustable-gas-block-750-bleed-off-solid.html","retrieved":"2026-10-06","via":"harvest"}},{"id":"joe-bob","value":0.25,"unit":"in","pm":0.005,"stated":"(2) 10-32 x 1/4\" Set Screws","source":{"type":"spec","publisher":"retailer","name":"Joe Bob Outfitters, Superlative Arms AR-15 / AR-10 .750\" Adjustable Bleed Off Gas Block - Solid - Melonite (SUP-SABO-DI-750SM)","url":"https://www.joeboboutfitters.com/Superlative-Arms-AR-15-AR-10-750-Adjustable-Bl-p/sup-sabo-di-750sm.htm","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"right-to-bear","reason":"Three sellers say 3/16; Joe Bob's 1/4 would stand 0.055 in out of the flat with its tip on the barrel, which no photo of the underside shows."},"note":"From the barrel's surface down, a 3/16 screw ends 0.008 in inside the foot's flat (0.570 less the journal's .375 is 0.195 of thread), as the photos of the underside show them: just below flush."}}},{"subject":"surefire-m340c-mini-scout-light-pro","title":"SureFire Mini Scout Light Pro (M340C-BK-PRO, M340C-TN-PRO)","dimensions":{"weight":{"label":"Weight (say with which batteries, and whether the mount is in it)","kind":"mass","measurements":[{"id":"surefire","value":3.65,"unit":"oz","pm":0.005,"stated":"WEIGHT W/ BATTERIES 3.65 oz (103.5 g)","source":{"type":"spec","publisher":"manufacturer","name":"SureFire, Mini Scout Light Pro, specifications","url":"https://www.surefire.com/mini-scout-light-pro/","retrieved":"2026-10-19","via":"harvest"}},{"id":"primaryarms","value":4.1,"unit":"oz","pm":0.05,"stated":"Weight 4.1 oz.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, SureFire M340C Mini Scout Light Pro Weapon Light - 500 Lumens - Black, specifications","url":"https://www.primaryarms.com/surefire-m340c-mini-scout-light-pro-weapon-light-500-lumens-black","retrieved":"2026-10-19","via":"harvest"}}],"adopt":{"from":"surefire","reason":"The maker's figure, on its page and its sheet alike. Primary Arms' 4.1 oz is a seller's, 0.45 oz more, which is about what a mount sold apart weighs less a little: it may count one, but the page doesn't say so. Kept, not averaged."},"note":"SureFire: with its one 123A (the sheet's battery table: 17 g each); whether a mount is counted isn't stated (each mount sold apart is 1.6 oz: .rail_mount_weight). The product information sheet repeats it: \"WEIGHT (w/batteries) 3.65 oz (103.5 g)\". Primary Arms' 4.1 oz is on both its pages (black and tan), and says nothing of what it counts."},"length":{"label":"Overall length","kind":"length","measurements":[{"id":"surefire","value":4.1,"unit":"in","pm":0.05,"stated":"LENGTH 4.1 in (10.4 cm)","source":{"type":"spec","publisher":"manufacturer","name":"SureFire, Mini Scout Light Pro, specifications","url":"https://www.surefire.com/mini-scout-light-pro/","retrieved":"2026-10-19","via":"harvest"}}],"note":"The tail cap's rear face to the bezel's front face: the sheet's drawing puts its 4.1 in dimension's extension lines at the outline's two ends (rows 95.75 and 2586.25 of the 600 dpi rendering, against the outline's 98 and 2588). The sheet's table repeats it: \"LENGTH 4.1 in (10.4 cm)\"."},"head_diameter":{"label":"Head (bezel) diameter","kind":"length","measurements":[{"id":"surefire","value":1.125,"unit":"in","pm":0.0005,"stated":"BEZEL DIAMETER 1.125 in (2.9 cm)","source":{"type":"spec","publisher":"manufacturer","name":"SureFire, Mini Scout Light Pro, specifications","url":"https://www.surefire.com/mini-scout-light-pro/","retrieved":"2026-10-19","via":"harvest"}}],"note":"The bezel's smooth front section ahead of its scalloped ring (the drawing's 1.125 in dimension is across it). The universal manual's table gives the KE1H bezel the same: \"BEZEL DIAMETER 1.125 in (2.9 cm)\". Tried against the published length on the sheet's drawing: at the length's scale (606.6 px/in, stroke centres) the bezel reads 1.113 in (1.1% under); on SureFire's right profile photo the length's and the bezel's scales agree within 1% too (the tube, the tail cap and the ring by their ratio to the bezel land within 0.02 in of the drawing's)."},"body_diameter":{"label":"Body diameter","kind":"length","measurements":[{"id":"drawing","value":0.746,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/surefire-m340c-mini-scout-light-pro fc4b86cba85b (SureFire's product information sheet, M340C-PRO.pdf page 2, BODY SPECS: the outline drawing rendered at 600 dpi)","scaleRef":"the published length between the outline's ends: 606.6 px/in at the strokes' centres; the axis at row 657.75 (the middle of every section whose two edges show)","method":"twice the top edge's height over the axis between the bands (the stroke at rows 430 to 433, columns 909 to 1244): 226.25 px; the lower edge there is under the mount's plate as drawn. By hand on the pixel values","via":"harvest"}}],"note":"Not published. The tube between the two bands, under the mount's plate (MH31: one 123A, 17 mm across, inside it). SureFire's right profile photo reads 0.759 by its ratio to the bezel (265 px over 393), the lit edges kept: 0.013 more than the drawing."},"tailcap_diameter":{"label":"Tail cap's shroud diameter","kind":"length","measurements":[{"id":"drawing","value":0.989,"unit":"in","pm":0.013,"source":{"type":"photo","photo":"references/surefire-m340c-mini-scout-light-pro fc4b86cba85b (SureFire's product information sheet (M340C-PRO.pdf), page 2, BODY SPECS: the outline drawing, rendered at 600 dpi)","scaleRef":"scale from surefire-m340c-mini-scout-light-pro.length = 4.1 in (x-extent 2487 px → 606.6 px/in)","method":"height (tooth tops, max over 0.05 in windows) along x [0.05, 0.38] of the traced outline (tools/trace.py); the Z68 tail cap's shroud, on the drawing","via":"harvest"}}],"note":"Not published. The Z68 tail cap's shroud, on the drawing; the right profile photo reads 1.002 by its ratio to the bezel, the left 0.982 (each photo yawed a little, opposite ways)."},"band_diameter":{"label":"Diameter of the body's two bands","kind":"length","measurements":[{"id":"drawing","value":0.786,"unit":"in","pm":0.011,"source":{"type":"photo","photo":"references/surefire-m340c-mini-scout-light-pro fc4b86cba85b (SureFire's product information sheet (M340C-PRO.pdf), page 2, BODY SPECS: the outline drawing, rendered at 600 dpi)","scaleRef":"scale from surefire-m340c-mini-scout-light-pro.length = 4.1 in (x-extent 2487 px → 606.6 px/in)","method":"height (tooth tops, max over 0.05 in windows) along x [1.03, 1.28] of the traced outline (tools/trace.py); the rear band, under which the rear ear hangs, on the drawing","via":"harvest"}}],"note":"Not published. The rear band (the rear ear hangs under it); the front band, which the front ear hangs under, reads the same on the drawing."},"ring_diameter":{"label":"Diameter of the scalloped ring behind the bezel (as drawn)","kind":"length","measurements":[{"id":"drawing","value":1.174,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/surefire-m340c-mini-scout-light-pro fc4b86cba85b (SureFire's product information sheet (M340C-PRO.pdf), page 2, BODY SPECS: the outline drawing, rendered at 600 dpi)","scaleRef":"scale from surefire-m340c-mini-scout-light-pro.length = 4.1 in (x-extent 2487 px → 606.6 px/in)","method":"height (tooth tops, max over 0.05 in windows) along x [3.08, 3.27] of the traced outline (tools/trace.py); the faceted ring behind the bezel, on the drawing","via":"harvest"}}],"note":"Not published. Wider than the published bezel diameter, which is the smooth section ahead of it. SureFire's right profile photo reads it 1.182 by its ratio to the bezel; the Dual Fuel's ring read 1.178 on its own photo."},"shroud_cone_x":{"label":"The tail cap shroud's cone, 0.45 in off the axis, ahead of the rear face","kind":"length","measurements":[{"id":"drawing","value":0.457,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/surefire-m340c-mini-scout-light-pro fc4b86cba85b (SureFire's product information sheet (M340C-PRO.pdf), page 2, BODY SPECS: the outline drawing, rendered at 600 dpi)","scaleRef":"scale from surefire-m340c-mini-scout-light-pro.length = 4.1 in (x-extent 2487 px → 606.6 px/in)","method":"x_min in x [0.35, 0.55] in y [0.445, 0.455] of the traced outline (tools/trace.py); the tail cap shroud's cone, where the top edge comes down through 0.45 in off the axis","via":"harvest"}}]},"clamp_rear_x":{"label":"Rear edge of the Picatinny mount's plate (the rear band's front edge), ahead of the rear face","kind":"length","measurements":[{"id":"drawing","value":1.317,"unit":"in","pm":0.016,"source":{"type":"photo","photo":"references/surefire-m340c-mini-scout-light-pro fc4b86cba85b (SureFire's product information sheet (M340C-PRO.pdf), page 2, BODY SPECS: the outline drawing, rendered at 600 dpi)","scaleRef":"scale from surefire-m340c-mini-scout-light-pro.length = 4.1 in (x-extent 2487 px → 606.6 px/in)","method":"x_min in x [1.2, 1.4] in y [0.38, 0.39] of the traced outline (tools/trace.py); the rear band's front edge, where the top edge comes down through 0.385 in off the axis: the plate's rear edge is drawn on it","via":"harvest"}}],"note":"The drawing draws the plate's rear edge on the rear band's front edge, and SureFire's right profile photo shows them in line. The plate is the M-1913-S's: its length (.clamp_front_x less this) is the Dual Fuel's within 0.02 in."},"clamp_front_x":{"label":"Front edge of the Picatinny mount's plate (the front band's rear edge), ahead of the rear face","kind":"length","measurements":[{"id":"drawing","value":1.902,"unit":"in","pm":0.023,"source":{"type":"photo","photo":"references/surefire-m340c-mini-scout-light-pro fc4b86cba85b (SureFire's product information sheet (M340C-PRO.pdf), page 2, BODY SPECS: the outline drawing, rendered at 600 dpi)","scaleRef":"scale from surefire-m340c-mini-scout-light-pro.length = 4.1 in (x-extent 2487 px → 606.6 px/in)","method":"x_max in x [1.8, 2.0] in y [0.38, 0.39] of the traced outline (tools/trace.py); the front band's rear edge, where the top edge rises through 0.385 in off the axis: the plate's front edge is drawn on it","via":"harvest"}}]},"head_step_x":{"label":"Step onto the head's rear, ahead of the rear face","kind":"length","measurements":[{"id":"drawing","value":2.324,"unit":"in","pm":0.028,"source":{"type":"photo","photo":"references/surefire-m340c-mini-scout-light-pro fc4b86cba85b (SureFire's product information sheet (M340C-PRO.pdf), page 2, BODY SPECS: the outline drawing, rendered at 600 dpi)","scaleRef":"scale from surefire-m340c-mini-scout-light-pro.length = 4.1 in (x-extent 2487 px → 606.6 px/in)","method":"x_min in x [2.2, 2.45] in y [0.455, 0.465] of the traced outline (tools/trace.py); the step onto the head's rear, where the top edge rises through 0.46 in off the axis","via":"harvest"}}]},"ring_front_x":{"label":"The scalloped ring's front edge (where the bezel's smooth section begins), ahead of the rear face","kind":"length","measurements":[{"id":"drawing","value":3.28,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/surefire-m340c-mini-scout-light-pro fc4b86cba85b (SureFire's product information sheet (M340C-PRO.pdf), page 2, BODY SPECS: the outline drawing, rendered at 600 dpi)","scaleRef":"scale from surefire-m340c-mini-scout-light-pro.length = 4.1 in (x-extent 2487 px → 606.6 px/in)","method":"x_max in x [3.1, 3.4] in y [0.57, 0.58] of the traced outline (tools/trace.py); the faceted ring's front edge, where the top edge comes down through 0.575 in off the axis","via":"harvest"}}]},"ring_rear_x":{"label":"The scalloped ring's rear edge, ahead of the rear face","kind":"length","measurements":[{"id":"drawing","value":2.967,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/surefire-m340c-mini-scout-light-pro fc4b86cba85b (SureFire's product information sheet, M340C-PRO.pdf page 2, BODY SPECS: the outline drawing rendered at 600 dpi)","scaleRef":"the published length between the outline's ends: 606.6 px/in at the strokes' centres, the rear face at column 100; the axis at row 657.75","method":"where the top edge rises through 0.575 in off the axis out of the groove behind the ring (row 308.9, about column 1900); by hand on the pixel values","via":"harvest"}}]},"ring_flats":{"label":"Flats round the scalloped ring behind the bezel","kind":"count","measurements":[{"id":"drawing","value":6,"unit":"count","source":{"type":"photo","photo":"references/surefire-m340c-mini-scout-light-pro fc4b86cba85b (SureFire's product information sheet, M340C-PRO.pdf page 2, BODY SPECS: the outline drawing rendered at 600 dpi)","scaleRef":"the published length between the outline's ends: 606.6 px/in at the strokes' centres, the rear face at column 100; the axis at row 657.75","method":"the middle flat's two edges and its neighbours' inner edges down columns 1915 to 2065, against a six-fold and an eight-fold ring's","via":"harvest"}}],"note":"Counted on the drawing: one flat square to its line of sight (rows 557.5 to 758.5 at column 1930) and its two neighbours, whose inner edges stand 245 px off the axis and whose outer edges run out at the ring's silhouette: a flat 16.4 degrees either side of its middle (its distance from the axis over the ring's radius), centred 58 to 60 degrees from the middle one, which only a six-fold ring puts there (eight would put them at 45). Primary Arms' photographs of the tan light show the same flats."},"ring_flat_rear_x":{"label":"Where the ring's flats are read at their rear, ahead of the rear face","kind":"length","measurements":[{"id":"drawing","value":3.017,"unit":"in","pm":0.003,"source":{"type":"photo","photo":"references/surefire-m340c-mini-scout-light-pro fc4b86cba85b (SureFire's product information sheet, M340C-PRO.pdf page 2, BODY SPECS: the outline drawing rendered at 600 dpi)","scaleRef":"the published length between the outline's ends: 606.6 px/in at the strokes' centres, the rear face at column 100; the axis at row 657.75","method":"column 1930, chosen near the flat's rear end, clear of the ring's rear round","via":"harvest"}}]},"ring_flat_front_x":{"label":"Where the ring's flats are read at their front, ahead of the rear face","kind":"length","measurements":[{"id":"drawing","value":3.239,"unit":"in","pm":0.003,"source":{"type":"photo","photo":"references/surefire-m340c-mini-scout-light-pro fc4b86cba85b (SureFire's product information sheet, M340C-PRO.pdf page 2, BODY SPECS: the outline drawing rendered at 600 dpi)","scaleRef":"the published length between the outline's ends: 606.6 px/in at the strokes' centres, the rear face at column 100; the axis at row 657.75","method":"column 2065, chosen near the flat's front end, clear of the ring's front chamfer","via":"harvest"}}]},"ring_flat_rear_from_axis":{"label":"A ring flat's distance from the axis at its rear reading","kind":"length","measurements":[{"id":"drawing","value":0.5627,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/surefire-m340c-mini-scout-light-pro fc4b86cba85b (SureFire's product information sheet, M340C-PRO.pdf page 2, BODY SPECS: the outline drawing rendered at 600 dpi)","scaleRef":"the published length between the outline's ends: 606.6 px/in at the strokes' centres, the rear face at column 100; the axis at row 657.75","method":"the middle flat's edges at rows 557.5 and 758.5 down column 1930 (stroke centres): half its chord 100.5 px on the ring's radius of 355.75 (rows 302 and 1013.5): sqrt(355.75^2 - 100.5^2) = 341.3 px","via":"harvest"}}],"note":"Each flat leans: it is deeper at its rear than at its front (the drawing's facet narrows forward, 201 px across at column 1930 and 145 at 2065)."},"ring_flat_front_from_axis":{"label":"A ring flat's distance from the axis at its front reading","kind":"length","measurements":[{"id":"drawing","value":0.5742,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/surefire-m340c-mini-scout-light-pro fc4b86cba85b (SureFire's product information sheet, M340C-PRO.pdf page 2, BODY SPECS: the outline drawing rendered at 600 dpi)","scaleRef":"the published length between the outline's ends: 606.6 px/in at the strokes' centres, the rear face at column 100; the axis at row 657.75","method":"the middle flat's edges at rows 585.5 and 730.5 down column 2065: half its chord 72.5 px on the ring's radius of 355.75: 348.3 px","via":"harvest"}}]},"shroud_holes":{"label":"Holes round the Z68 tail cap's shroud","kind":"count","measurements":[{"id":"photo","value":4,"unit":"count","source":{"type":"photo","photo":"references/surefire-m340c-mini-scout-light-pro ff47d3e34a2f (Primary Arms, M340C-TN-PRO_01: the tan body from behind, 2200 x 1467)","scaleRef":"none: a count","method":"the holes round the shroud's rim, counted all the way round","via":"harvest"}}],"note":"Counted on Primary Arms' photograph of the tan light from behind (ff47d3e34a2f), where the shroud's rim shows all the way round: four, evenly spaced. The drawing and SureFire's two profile photos each show two, about 45 degrees either side of the line of sight, as four so turned show."},"shroud_hole_x":{"label":"The shroud's holes' centres, ahead of the rear face","kind":"length","measurements":[{"id":"drawing","value":0.11,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/surefire-m340c-mini-scout-light-pro fc4b86cba85b (SureFire's product information sheet, M340C-PRO.pdf page 2, BODY SPECS: the outline drawing rendered at 600 dpi)","scaleRef":"the published length between the outline's ends: 606.6 px/in at the strokes' centres, the rear face at column 100; the axis at row 657.75","method":"the two holes' outlines (ovals, seen 44.5 degrees off square) from column 130 to 203.5 at their middles (rows 448 and 868.5): their middle, 166.75; by hand","via":"harvest"}}]},"shroud_hole_diameter":{"label":"Diameter of the shroud's holes","kind":"length","measurements":[{"id":"drawing","value":0.121,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/surefire-m340c-mini-scout-light-pro fc4b86cba85b (SureFire's product information sheet, M340C-PRO.pdf page 2, BODY SPECS: the outline drawing rendered at 600 dpi)","scaleRef":"the published length between the outline's ends: 606.6 px/in at the strokes' centres, the rear face at column 100; the axis at row 657.75","method":"the ovals' length along the body between their strokes' centres, columns 130 to 203.5: 73.5 px; by hand","via":"harvest"}}],"note":"Along the body, where a round hole seen from the side keeps its whole diameter; across, the drawing's ovals are 0.67 of it, as a round hole 45 degrees off square shows."},"front_ear_front_x":{"label":"Front face of the pivot's front ear, ahead of the rear face","kind":"length","measurements":[{"id":"drawing","value":2.029,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/surefire-m340c-mini-scout-light-pro fc4b86cba85b (SureFire's product information sheet, M340C-PRO.pdf page 2, BODY SPECS: the outline drawing rendered at 600 dpi)","scaleRef":"the published length between the outline's ends: 606.6 px/in at the strokes' centres, the rear face at column 100","method":"the ear's front face, the vertical stroke at column 1330.5 over rows 560 to 850 (the plate's front edge and the front band's rear edge are at 1255.5): by hand on the pixel values","via":"harvest"}}]},"screw_head_front_x":{"label":"Front face of the pivot screw's head (the Z93 shoulder screw), ahead of the rear face","kind":"length","measurements":[{"id":"drawing","value":2.178,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/surefire-m340c-mini-scout-light-pro fc4b86cba85b (SureFire's product information sheet, M340C-PRO.pdf page 2, BODY SPECS: the outline drawing rendered at 600 dpi)","scaleRef":"the published length between the outline's ends: 606.6 px/in at the strokes' centres","method":"the head's front face, the strokes at columns 1418.5 and 1424.5 over rows 750 to 850: their middle, 1421.5; by hand","via":"harvest"}}]},"screw_head_diameter":{"label":"Diameter of the pivot screw's head","kind":"length","measurements":[{"id":"drawing","value":0.346,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/surefire-m340c-mini-scout-light-pro fc4b86cba85b (SureFire's product information sheet, M340C-PRO.pdf page 2, BODY SPECS: the outline drawing rendered at 600 dpi)","scaleRef":"the published length between the outline's ends: 606.6 px/in","method":"the head's two edges down column 1400, the strokes at rows 648 to 651 and 858 to 861: 210 px between their centres; by hand","via":"harvest"}}],"note":"A disc about the pivot's axis, which runs along the body: any view round the body sees its whole diameter, whatever way the drawing's mount is swung."},"pivot_top_below_axis":{"label":"Top of the mount's barrel, below the body's axis","kind":"length","measurements":[{"id":"surefire-right","value":0.43,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/surefire-m340c-mini-scout-light-pro b1f3e5726acc (SureFire's gallery, M340C-BK-PRO-profileR: the light on its Picatinny mount, right side, on white, 1500 x 1500)","scaleRef":"frame from the reviewed holes cone, clamp_rear, clamp_front, head_step, ring_front (355.3 px/in, rms 0.009 in over 5 points)","method":"−y_max of the traced outline (tools/trace.py); the top of the mount's barrel, under the white gap between it and the tube","via":"harvest"}}],"note":"A white gap of 0.07 in shows between the tube and the barrel. The left profile photo reads 0.407 and its ears' lowest point 0.750: the pivot 0.04 nearer the axis than in the right one, as a mount swung some 20 degrees out of the photo's plane would show it (its plate there reads as long as in the right one, so it isn't foreshortened along its length: the body is turned on the pivot). The right one, whose plate is square to the lens, is taken."},"ear_bottom_below_axis":{"label":"Lowest point of the pivot's ears, below the body's axis","kind":"length","measurements":[{"id":"surefire-right","value":0.788,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/surefire-m340c-mini-scout-light-pro b1f3e5726acc (SureFire's gallery, M340C-BK-PRO-profileR: the light on its Picatinny mount, right side, on white, 1500 x 1500)","scaleRef":"frame from the reviewed holes cone, clamp_rear, clamp_front, head_step, ring_front (355.3 px/in, rms 0.009 in over 5 points)","method":"−y_min of the traced outline (tools/trace.py); the rear ear's lowest point (the front one's reads 0.004 less)","via":"harvest"}}],"note":"The ears are round about the pivot and flush with the mount's barrel between them (SureFire's rear three-quarter photos). With .pivot_top_below_axis it gives the pivot: its axis midway between the two (.pivot_centre_below_axis)."},"barrel_rear_x":{"label":"Rear end of the mount's barrel (the rear ear's front face), ahead of the rear face","kind":"length","measurements":[{"id":"surefire-right","value":1.315,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/surefire-m340c-mini-scout-light-pro b1f3e5726acc (SureFire's gallery, M340C-BK-PRO-profileR: the light on its Picatinny mount, right side, on white, 1500 x 1500)","scaleRef":"frame from the reviewed holes cone, clamp_rear, clamp_front, head_step, ring_front (355.3 px/in, rms 0.009 in over 5 points)","method":"x_max of the traced outline (tools/trace.py); the rear ear's front face, against the barrel's rear end","via":"harvest"}}]},"barrel_front_x":{"label":"Front end of the mount's barrel (the front ear's rear face), ahead of the rear face","kind":"length","measurements":[{"id":"surefire-right","value":1.92,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/surefire-m340c-mini-scout-light-pro b1f3e5726acc (SureFire's gallery, M340C-BK-PRO-profileR: the light on its Picatinny mount, right side, on white, 1500 x 1500)","scaleRef":"frame from the reviewed holes cone, clamp_rear, clamp_front, head_step, ring_front (355.3 px/in, rms 0.009 in over 5 points)","method":"x_min of the traced outline (tools/trace.py); the front ear's rear face, against the barrel's front end","via":"harvest"}}],"note":"With .barrel_rear_x, the barrel is 0.60 in long between the ears on this light's photo; the Dual Fuel's photo reads its 0.553. The ears are the body's and the barrel the mount's, so one of the two readings is off by about 0.05 in, or the two bodies' ears stand apart differently and the mount's barrel is not what fills the gap; the model draws this light's."},"pivot_centre_below_axis":{"label":"The pivot's axis below the body's axis","kind":"length","measurements":[{"id":"photo","value":0.609,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"({.pivot_top_below_axis} + {.ear_bottom_below_axis}) / 2","via":"harvest"}}]},"barrel_diameter":{"label":"Diameter of the mount's barrel (and of the ears round it)","kind":"length","measurements":[{"id":"dual-fuel","value":0.36,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{surefire-scout-light-pro-dual-fuel.ear_bottom_below_axis} - {surefire-scout-light-pro-dual-fuel.pivot_top_below_axis}","via":"harvest"}},{"id":"surefire-right","value":0.358,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{.ear_bottom_below_axis} - {.pivot_top_below_axis}","via":"harvest"}}],"adopt":{"from":"dual-fuel","reason":"The same mount's figure on file; this light's reading agrees within the ±."},"note":"The mount's own: the M-1913-S's barrel is the Dual Fuel's (the same mount). This light's right profile reads 0.358 between the barrel's top and the ears' lowest point, 0.002 from it."},"axis_above_mount":{"label":"The body's axis above the mounting face (the rail's top, the handguard's face)","kind":"length","measurements":[{"id":"dual-fuel","value":0.19,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{surefire-scout-light-pro-dual-fuel.axis_above_mount}","via":"harvest"}}],"note":"For the M-1913-S hanging straight from its pivot, as SureFire photographs it: the body stands beside the rail and its axis is at the pivot's height above the rail's top, which is the mount's (the Dual Fuel's ledger has how it was read, and why it is the most it can be). On the M-MLOK-S the body stands over the face instead: .mlok_pivot_above_face plus .pivot_centre_below_axis."},"rail_centre_below_axis":{"label":"The rail's centre line below the body's axis, the Picatinny mount hanging straight (as photographed)","kind":"length","measurements":[{"id":"dual-fuel","value":1.081,"unit":"in","pm":0.035,"source":{"type":"derived","expr":"{.pivot_centre_below_axis} + {surefire-scout-light-pro-dual-fuel.rail_centre_below_axis} - ({surefire-scout-light-pro-dual-fuel.pivot_top_below_axis} + {surefire-scout-light-pro-dual-fuel.ear_bottom_below_axis}) / 2","via":"harvest"}}],"note":"The pivot's place under this body, and the rail's centre line where the M-1913-S holds it below its pivot (the Dual Fuel's 1.123 less its pivot's 0.651). This light's own photo has the plate 0.04 in longer below the pivot than the Dual Fuel's (.jaw_bottom_below_axis): if the rail's far edge follows the jaw, its centre line is 0.02 in further than this."},"jaw_bottom_below_axis":{"label":"Underside of the Picatinny mount's moving jaw, below the body's axis","kind":"length","measurements":[{"id":"surefire-right","value":1.618,"unit":"in","pm":0.007,"source":{"type":"photo","photo":"references/surefire-m340c-mini-scout-light-pro b1f3e5726acc (SureFire's gallery, M340C-BK-PRO-profileR: the light on its Picatinny mount, right side, 1500 x 1500)","scaleRef":"the `clamp` trace's frame for this photo: five of the body's steps placed where the drawing's trace has them (355.3 px/in)","method":"−y_min of the traced outline (tools/trace.py): the jaw's underside, the mount screw's slotted head under it (to row 1145) boxed out","via":"harvest"}},{"id":"dual-fuel","value":1.578,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{.pivot_centre_below_axis} + {surefire-scout-light-pro-dual-fuel.jaw_bottom_below_axis} - ({surefire-scout-light-pro-dual-fuel.pivot_top_below_axis} + {surefire-scout-light-pro-dual-fuel.ear_bottom_below_axis}) / 2","via":"harvest"}}],"adopt":{"from":"surefire-right","reason":"This light's own photo of its own mount, square to the lens, and its left profile agrees with it. The Dual Fuel's reading is kept beside it: 0.04 in shorter, outside both ±."},"note":"Read two ways that don't agree: on this light's own right profile, and as the Dual Fuel's jaw below its pivot carried onto this light's pivot. This light's right profile has the plate's end 1.009 in below the pivot, and its left one (by its own bezel, so a little large) 1.038; the Dual Fuel's two read 0.969. Either the Dual Fuel's photographs see its plate swung some 15 degrees out of their plane, or the mount was changed between them. The model draws this light's plate as its own photo has it."},"clamp_thickness":{"label":"Thickness of the Picatinny mount's plate (its SF face to its rail side)","kind":"length","measurements":[{"id":"dual-fuel","value":0.22,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{surefire-scout-light-pro-dual-fuel.clamp_thickness}","via":"harvest"}}]},"jaw_reach":{"label":"How far the Picatinny mount's jaws reach below the rail's top","kind":"length","measurements":[{"id":"dual-fuel","value":0.1,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{surefire-scout-light-pro-dual-fuel.jaw_reach}","via":"harvest"}}]},"recoil_bar_width":{"label":"Width of the recoil bar under the Picatinny mount's plate (along the rail)","kind":"length","measurements":[{"id":"dual-fuel","value":0.2,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{surefire-scout-light-pro-dual-fuel.recoil_bar_width}","via":"harvest"}}]},"hook_back_beyond_pivot":{"label":"Picatinny mount: how far the fixed hook's block reaches past the pivot's axis, away from the rail's centre","kind":"length","measurements":[{"id":"dual-fuel","value":0.07,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{surefire-scout-light-pro-dual-fuel.hook_back_beyond_pivot}","via":"harvest"}}]},"mount_screw_head_diameter":{"label":"Picatinny mount: diameter of the mount screw's head, at the moving jaw's end","kind":"length","measurements":[{"id":"dual-fuel","value":0.19,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{surefire-scout-light-pro-dual-fuel.mount_screw_head_diameter}","via":"harvest"}}]},"mount_screw_head_proud":{"label":"Picatinny mount: how far the mount screw's head stands out of the moving jaw","kind":"length","measurements":[{"id":"dual-fuel","value":0.04,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{surefire-scout-light-pro-dual-fuel.mount_screw_head_proud}","via":"harvest"}}],"note":"The Dual Fuel's figure; this light's right profile shows the slotted head 11 to 13 px (0.03 to 0.04 in) under the jaw, the same."},"rail_mount_weight":{"label":"Weight of the Picatinny mount sold apart (M-1913-S)","kind":"mass","measurements":[{"id":"dual-fuel","value":1.6,"unit":"oz","pm":0.05,"source":{"type":"derived","expr":"{surefire-scout-light-pro-dual-fuel.rail_mount_weight}","via":"harvest"}}],"note":"The same mount's figure, on its own page (the Dual Fuel's ledger quotes it). Whether the light's 3.65 oz counts a mount isn't stated."},"lugs":{"label":"M-LOK slots its mount's lugs span","kind":"count","measurements":[{"id":"dual-fuel","value":1,"unit":"count","source":{"type":"derived","expr":"{surefire-scout-light-pro-dual-fuel.lugs}","via":"harvest"}}],"note":"The M-MLOK-S's: two screws with T-nuts about 0.64 in apart, both in one slot (worked out from its photos in the Dual Fuel's ledger). The manual: \"M-MLOK-S: See Magpul instructions enclosed\"; those instructions aren't on file."},"reach_inside":{"label":"Reach inside the handguard (below the mounting face, tightened)","kind":"length","measurements":[],"note":"Not sourced, for the M-MLOK-S on either light: the Magpul sheet the manual says is enclosed isn't on file."},"mlok_screw_spacing":{"label":"M-LOK mount: its two screws, centre to centre","kind":"length","measurements":[{"id":"dual-fuel","value":0.64,"unit":"in","pm":0.07,"source":{"type":"derived","expr":"{surefire-scout-light-pro-dual-fuel.mlok_screw_spacing}","via":"harvest"}}]},"mlok_base_width":{"label":"M-LOK mount: width of its base","kind":"length","measurements":[{"id":"dual-fuel","value":0.4,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{surefire-scout-light-pro-dual-fuel.mlok_base_width}","via":"harvest"}}]},"mlok_pivot_above_face":{"label":"M-LOK mount: the pivot's axis above its mounting face","kind":"length","measurements":[{"id":"dual-fuel","value":0.4,"unit":"in","pm":0.1,"source":{"type":"derived","expr":"{surefire-scout-light-pro-dual-fuel.mlok_pivot_above_face}","via":"harvest"}}]},"mlok_base_thickness":{"label":"M-LOK mount: thickness of its base","kind":"length","measurements":[{"id":"dual-fuel","value":0.15,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{surefire-scout-light-pro-dual-fuel.mlok_base_thickness}","via":"harvest"}}]},"mlok_counterbore_diameter":{"label":"M-LOK mount: diameter of the counterbore round each screw","kind":"length","measurements":[{"id":"dual-fuel","value":0.31,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{surefire-scout-light-pro-dual-fuel.mlok_counterbore_diameter}","via":"harvest"}}]},"mlok_mount_weight":{"label":"Weight of the M-LOK mount sold apart (M-MLOK-S)","kind":"mass","measurements":[{"id":"dual-fuel","value":1.6,"unit":"oz","pm":0.05,"source":{"type":"derived","expr":"{surefire-scout-light-pro-dual-fuel.mlok_mount_weight}","via":"harvest"}}]},"width":{"label":"Overall width (with its mount and switch)","kind":"length","measurements":[],"note":"Not published, and it changes as the mount is swivelled."},"lens_recess":{"label":"How far the lens sits behind the bezel's front face","kind":"length","measurements":[{"id":"assumed","value":0.08,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows the bezel in section (the Dual Fuel's script assumed the same).","via":"harvest"}}]}}},{"subject":"surefire-procomp-556","title":"SureFire ProComp 556 Muzzle Brake, PROCOMP-556-1/2-28","dimensions":{"overall_length":{"label":"Overall length (rear face to front face)","kind":"length","measurements":[{"id":"kygunco","value":2.5,"unit":"in","pm":0.05,"stated":"LENGTH: 5.56 mm - 2.5 in (6.35 cm), 7.62 mm - 2.7 in (6.85 cm)","source":{"type":"spec","publisher":"retailer","name":"KYGunCo, Surefire Procomp 556 Muzzle Break 1/2x28 - Black (its SPECIFICATIONS block, SureFire's sheet reprinted)","url":"https://www.kygunco.com/product/surefire-procomp-556-1-2-28-procomp-556-muzzle-break-1-2x28-black","retrieved":"2026-10-28","via":"harvest"},"note":"The sheet's two models in one line; this is the 5.56's. SureFire's sheet adds that the length \"may vary, depending on which SureFire adapter is used\" (the discovery's reading of the sheet, which isn't on file)."},{"id":"redcon1","value":2.5,"unit":"in","pm":0.05,"stated":"Length: 2.5 in","source":{"type":"spec","publisher":"retailer","name":"Redcon1 Tactical, SureFire ProComp Muzzle Brake 5.56 - Black (its specification list, PROCOMP-556-1/2-28)","url":"https://redcon1tactical.com/ar-15/magazines/followers/surefire-procomp-muzzle-brake-5-56-black.html?category_id=230","retrieved":"2026-10-28","via":"harvest"}},{"id":"primary-arms","value":2.5,"unit":"in","pm":0.05,"stated":"Caliber: 5.56 mm (.223 caliber) Length: 2.5”","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, SureFire ProComp Muzzle Brake - 1/2X28 (its feature list)","url":"https://www.primaryarms.com/surefire-procomp-muzzle-brake-1-2x28-procomp556-1-2-28","retrieved":"2026-10-28","via":"harvest"}},{"id":"ctd","value":2.67,"unit":"in","pm":0.005,"stated":"Melonite Finish Length 2.67\" Black Includes Crush Washer","source":{"type":"spec","publisher":"retailer","name":"Cheaper Than Dirt, SureFire ProComp 5.56 Muzzle Brake 1/2\"x28 (FC-084871323512)","url":"https://www.cheaperthandirt.com/surefire-procomp-556-muzzle-brake-5.56-nato.223-rem-threaded-12x28-heat-treated-stainless-steel-black-melonite-finish-procomp-556-12-28/FC-084871323512.html","retrieved":"2026-10-28","via":"harvest"},"note":"One seller's own figure, 0.17 longer than the maker's; whether it counts a crush washer it says comes in the box, it doesn't say."},{"id":"photo","value":2.49,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/surefire-procomp-556 df201d3f2cee (Primary Arms PROCOMP556-1-2-28_03, 2200 x 1467)","scaleRef":"its own collar's width, 438 px, as od (0.864) less the 2% a black edge reads thin on white (447 px)","method":"the length between the end faces' centres (1287.5 px, each end face's ellipse halved), over the collar's width: 2.94 widths as read, 2.88 with the thin reading taken out","via":"harvest"},"note":"A check of the published length against the published width: 2.49 to 2.54 by how thin the photo reads the black collar."}],"adopt":{"from":"kygunco","reason":"SureFire's own sheet as KYGunCo reprints it; two more sellers (Redcon1, Primary Arms) say the same, and the photo's length over its width agrees. Cheaper Than Dirt's 2.67 is one seller's and stays visible."}},"length":{"label":"Length ahead of the barrel's shoulder, installed (to the front face)","kind":"length","measurements":[{"id":"seated","value":2.5,"unit":"in","source":{"type":"derived","expr":"{.overall_length}","via":"harvest"},"note":"The device's rear face on the barrel's shoulder."}],"note":"No washer is drawn: one seller says one is in the box (Cheaper Than Dirt: \"Includes Crush Washer\"), SureFire's text as the others reprint it says nothing of how it is timed but its 6 o'clock pilot hole (\"allows indexing the adapter at bottom dead center\", Primary Arms), and no photo on file shows a washer. Seated on the shoulder, the device's own length is what it adds."},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"kygunco","value":3.4,"unit":"oz","stated":"WEIGHT: 5.56 mm - 3.4 oz (96 g), 7.62 mm - 3.1 oz (90 g)","source":{"type":"spec","publisher":"retailer","name":"KYGunCo, Surefire Procomp 556 Muzzle Break 1/2x28 - Black (its SPECIFICATIONS block, SureFire's sheet reprinted)","url":"https://www.kygunco.com/product/surefire-procomp-556-1-2-28-procomp-556-muzzle-break-1-2x28-black","retrieved":"2026-10-28","via":"harvest"}},{"id":"redcon1","value":3.4,"unit":"oz","stated":"Weight: 3.4 oz","source":{"type":"spec","publisher":"retailer","name":"Redcon1 Tactical, SureFire ProComp Muzzle Brake 5.56 - Black (its specification list, PROCOMP-556-1/2-28)","url":"https://redcon1tactical.com/ar-15/magazines/followers/surefire-procomp-muzzle-brake-5-56-black.html?category_id=230","retrieved":"2026-10-28","via":"harvest"}}],"adopt":{"from":"kygunco","reason":"SureFire's sheet as KYGunCo reprints it; Redcon1 says the same. KYGunCo's \"Weight 1 lb\" beside its stock number is a shipping weight."}},"od":{"label":"Largest outside diameter (the collar, and the lands at 12 and 6 o'clock the whole length)","kind":"length","measurements":[{"id":"redcon1","value":0.864,"unit":"in","pm":0.0005,"stated":"Width: 0.864 in","source":{"type":"spec","publisher":"retailer","name":"Redcon1 Tactical, SureFire ProComp Muzzle Brake 5.56 - Black (its specification list, PROCOMP-556-1/2-28)","url":"https://redcon1tactical.com/ar-15/magazines/followers/surefire-procomp-muzzle-brake-5-56-black.html?category_id=230","retrieved":"2026-10-28","via":"harvest"}},{"id":"side","value":0.85,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/surefire-procomp-556 df201d3f2cee (Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467)","scaleRef":"its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864)","method":"the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)","via":"harvest"},"note":"438 px at 515.0 px/in; a black edge on white reads up to 3% thin."},{"id":"below","value":0.84,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/surefire-procomp-556 aa48bc88d85b (Primary Arms PROCOMP556-1-2-28_02: the device standing muzzle up, square on its underside, from about 3 degrees above, 2200 x 1467)","scaleRef":"its length between the end faces' centres, 1224 px, as overall_length (2.5): 489.6 px/in; across the device, its collar's width (411 px) as od (0.864)","method":"the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges as read on those runs (± 3 px), stations from the rear face's centre (row 1369)","via":"harvest"},"note":"The collar, 411 px at 489.6 px/in."}],"adopt":{"from":"redcon1","reason":"The one published width (a seller's table: provisional). Both photos read it within their ±, 1.6% and 2.8% under, as a black part on white reads."},"note":"One diameter end to end: in the side view (_03) the outline's height is the collar's from the rear taper to the front face (438 to 442 px): the lands at the top and bottom are left round."},"flats_across":{"label":"Across the two port flats (the 3 and 9 o'clock faces the windows are cut through)","kind":"length","measurements":[{"id":"below","value":0.774,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/surefire-procomp-556 aa48bc88d85b (Primary Arms PROCOMP556-1-2-28_02: the device standing muzzle up, square on its underside, from about 3 degrees above, 2200 x 1467)","scaleRef":"its length between the end faces' centres, 1224 px, as overall_length (2.5): 489.6 px/in; across the device, its collar's width (411 px) as od (0.864)","method":"the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges as read on those runs (± 3 px), stations from the rear face's centre (row 1369)","via":"harvest"},"note":"The outline's width ahead of the collar, between the windows and ahead of them: 368 px for the collar's 411 (0.8954 of it), from the front face to row 788."},{"id":"side-chord","value":0.738,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/surefire-procomp-556 df201d3f2cee (Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467)","scaleRef":"its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864)","method":"the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)","via":"harvest"},"note":"The flat facing the lens between the windows, read on its tone: an even dark (22 of 255) from column 1004 to 1232, a chord 228 px wide on a collar 438 across; a flat whose chord that is stands 0.854 of the radius out."}],"adopt":{"from":"below","reason":"A silhouette, read square on. The other reading is a tone's edge, where the flat turns into the round; the two are 0.036 apart and stay visible."}},"flats_rear_x":{"label":"Port flats, rear end (from the rear face)","kind":"length","measurements":[{"id":"below","value":1.187,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/surefire-procomp-556 aa48bc88d85b (Primary Arms PROCOMP556-1-2-28_02: the device standing muzzle up, square on its underside, from about 3 degrees above, 2200 x 1467)","scaleRef":"its length between the end faces' centres, 1224 px, as overall_length (2.5): 489.6 px/in; across the device, its collar's width (411 px) as od (0.864)","method":"the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges as read on those runs (± 3 px), stations from the rear face's centre (row 1369)","via":"harvest"},"note":"The outline steps out to the collar's width at row 788, after a concave lit run-out over rows 760 to 788 (0.057)."}]},"flats_runout":{"label":"Port flats, the round run-out at their rear end, along the device","kind":"length","measurements":[{"id":"below","value":0.057,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/surefire-procomp-556 aa48bc88d85b (Primary Arms PROCOMP556-1-2-28_02: the device standing muzzle up, square on its underside, from about 3 degrees above, 2200 x 1467)","scaleRef":"its length between the end faces' centres, 1224 px, as overall_length (2.5): 489.6 px/in; across the device, its collar's width (411 px) as od (0.864)","method":"the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges as read on those runs (± 3 px), stations from the rear face's centre (row 1369)","via":"harvest"},"note":"Rows 760 to 788: the cutter's round, drawn as a quarter circle."}]},"rear_taper_x":{"label":"Rear taper, where it begins (from the rear face)","kind":"length","measurements":[{"id":"side","value":0.196,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/surefire-procomp-556 df201d3f2cee (Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467)","scaleRef":"its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864)","method":"the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)","via":"harvest"},"note":"The outline narrows from row 1302; a straight cone (0.55 px of width a row) to the end face's ellipse."},{"id":"below","value":0.182,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/surefire-procomp-556 aa48bc88d85b (Primary Arms PROCOMP556-1-2-28_02: the device standing muzzle up, square on its underside, from about 3 degrees above, 2200 x 1467)","scaleRef":"its length between the end faces' centres, 1224 px, as overall_length (2.5): 489.6 px/in; across the device, its collar's width (411 px) as od (0.864)","method":"the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges as read on those runs (± 3 px), stations from the rear face's centre (row 1369)","via":"harvest"},"note":"From row 1280."}],"adopt":{"from":"side","reason":"The larger view; the two are 0.014 apart, within their two ±."}},"rear_face_d":{"label":"Rear face, outside diameter (where the taper ends)","kind":"length","measurements":[{"id":"side","value":0.754,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/surefire-procomp-556 df201d3f2cee (Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467)","scaleRef":"its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864)","method":"the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)","via":"harvest"},"note":"The cone carried to the rear face's station: 0.873 of the collar's width."},{"id":"below","value":0.748,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/surefire-procomp-556 aa48bc88d85b (Primary Arms PROCOMP556-1-2-28_02: the device standing muzzle up, square on its underside, from about 3 degrees above, 2200 x 1467)","scaleRef":"its length between the end faces' centres, 1224 px, as overall_length (2.5): 489.6 px/in; across the device, its collar's width (411 px) as od (0.864)","method":"the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges as read on those runs (± 3 px), stations from the rear face's centre (row 1369)","via":"harvest"},"note":"0.866 of the collar's width."}],"adopt":{"from":"side","reason":"The two agree within 0.006."}},"grooves":{"label":"Grooves round the collar","kind":"count","measurements":[{"id":"side","value":3,"unit":"count","source":{"type":"photo","photo":"references/surefire-procomp-556 df201d3f2cee (Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467)","scaleRef":"its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864)","method":"the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)","via":"harvest"},"note":"Three notches in each edge of the outline, rows 1014 to 1126; three in the underside's (_02) at the same stations, and three in every three-quarter view."}]},"groove_front_x":{"label":"Front groove, its middle (from the rear face)","kind":"length","measurements":[{"id":"side","value":0.728,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/surefire-procomp-556 df201d3f2cee (Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467)","scaleRef":"its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864)","method":"the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)","via":"harvest"},"note":"Row 1028, the notch's middle on both edges; the underside's outline has it at 0.727."}]},"groove_pitch":{"label":"Grooves, middle to middle","kind":"length","measurements":[{"id":"side","value":0.0835,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/surefire-procomp-556 df201d3f2cee (Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467)","scaleRef":"its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864)","method":"the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)","via":"harvest"},"note":"Rows 1028, 1071 and 1114: 43 px apart."}]},"groove_width":{"label":"Groove, width at the surface","kind":"length","measurements":[{"id":"side","value":0.05,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/surefire-procomp-556 df201d3f2cee (Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467)","scaleRef":"its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864)","method":"the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)","via":"harvest"},"note":"26 px between where each notch leaves the outline's edge; its floor is about half that (12 to 16 px): the walls lean."}]},"groove_depth":{"label":"Groove, depth","kind":"length","measurements":[{"id":"side","value":0.018,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/surefire-procomp-556 df201d3f2cee (Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467)","scaleRef":"its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864)","method":"the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)","via":"harvest"},"note":"9 px on the left edge (895 to 904) and 10 on the right (1331 to 1321), of a collar 438 across."}]},"windows":{"label":"Port windows (each through from side to side)","kind":"count","measurements":[{"id":"side","value":2,"unit":"count","source":{"type":"photo","photo":"references/surefire-procomp-556 df201d3f2cee (Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467)","scaleRef":"its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864)","method":"the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)","via":"harvest"},"note":"Two openings in each port flat, the backdrop seen through both (rows 223 to 431 and 518 to 815); the underside's outline is notched at the same two places on each side, and every three-quarter view shows two a side."}]},"window_front_rear_x":{"label":"Front window, rear edge (from the rear face)","kind":"length","measurements":[{"id":"side","value":1.887,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/surefire-procomp-556 df201d3f2cee (Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467)","scaleRef":"its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864)","method":"the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)","via":"harvest"},"note":"Row 431: where the near face's edge meets the window's rear wall (lit, seen from above as a band with the bore's hole in it)."}]},"window_front_front_x":{"label":"Front window, front edge","kind":"length","measurements":[{"id":"side","value":2.291,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/surefire-procomp-556 df201d3f2cee (Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467)","scaleRef":"its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864)","method":"the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)","via":"harvest"},"note":"Row 223, where the backdrop first shows through."}]},"window_rear_rear_x":{"label":"Rear window, rear edge","kind":"length","measurements":[{"id":"side","value":1.142,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/surefire-procomp-556 df201d3f2cee (Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467)","scaleRef":"its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864)","method":"the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)","via":"harvest"},"note":"Row 815."}]},"window_rear_front_x":{"label":"Rear window, front edge","kind":"length","measurements":[{"id":"side","value":1.718,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/surefire-procomp-556 df201d3f2cee (Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467)","scaleRef":"its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864)","method":"the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)","via":"harvest"},"note":"Row 518."}]},"window_height":{"label":"Windows, height across the port face (12 to 6 o'clock)","kind":"length","measurements":[{"id":"side","value":0.584,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/surefire-procomp-556 df201d3f2cee (Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467)","scaleRef":"its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864)","method":"the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)","via":"harvest"},"note":"296 px of the collar's 438."}],"note":"Both windows the same, from column 971 to 1267. Their middle reads 6 px (0.012) above the outline's, as the 9 o'clock pilot hole's reads 12 px above it: the photo is turned a degree or two about the axis. Drawn on the axis: no source says the windows are off it (SureFire's \"offset porting\" is said of the bore, not drawn)."},"window_corner_r":{"label":"Windows, corner radius","kind":"length","measurements":[{"id":"side","value":0.09,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/surefire-procomp-556 df201d3f2cee (Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467)","scaleRef":"its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864)","method":"the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)","via":"harvest"},"note":"The see-through narrows over about 45 rows and 45 px at each end of each window."}]},"land_width":{"label":"Land between the two pockets (at 12 and at 6 o'clock), width","kind":"length","measurements":[{"id":"below","value":0.088,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/surefire-procomp-556 aa48bc88d85b (Primary Arms PROCOMP556-1-2-28_02: the device standing muzzle up, square on its underside, from about 3 degrees above, 2200 x 1467)","scaleRef":"its length between the end faces' centres, 1224 px, as overall_length (2.5): 489.6 px/in; across the device, its collar's width (411 px) as od (0.864)","method":"the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges as read on those runs (± 3 px), stations from the rear face's centre (row 1369)","via":"harvest"},"note":"Columns 1076 to 1118 (42 px), the darkest stripe down the underside, with the grooves across it."}]},"pocket_outer_z":{"label":"Pockets, outer edge, out from the middle (as seen square on the face they are cut in)","kind":"length","measurements":[{"id":"below","value":0.3,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/surefire-procomp-556 aa48bc88d85b (Primary Arms PROCOMP556-1-2-28_02: the device standing muzzle up, square on its underside, from about 3 degrees above, 2200 x 1467)","scaleRef":"its length between the end faces' centres, 1224 px, as overall_length (2.5): 489.6 px/in; across the device, its collar's width (411 px) as od (0.864)","method":"the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges as read on those runs (± 3 px), stations from the rear face's centre (row 1369)","via":"harvest"},"note":"Columns 950 and 1236, 144.5 and 141.5 px from the outline's middle; outside them, the round down to the port flats (to 0.387)."}]},"pocket_tilt":{"label":"Pockets, how far each floor is turned from the plane square to the land","kind":"angle","measurements":[{"id":"side","value":24,"unit":"deg","pm":6,"source":{"type":"photo","photo":"references/surefire-procomp-556 df201d3f2cee (Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467)","scaleRef":"its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864)","method":"the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)","via":"harvest"},"note":"The hole at the right edge, 25 px wide (columns 1293 to 1318) by 63 px along the device (rows 875 to 938): 0.40, a floor 66 degrees from the line of sight, 24 from square to the land. The floor's band beside the side view's edge (54 px, from 0.75 of the radius out) agrees with 15 to 25. And the underside (aa48bc88d85b) checks it: the grooves run on into each bottom pocket for 0.04 inside its outer edge (to column 974, 0.262 out, rows 1020 to 1112) and stop where the floor is as deep as a groove; a floor through the outer edge on the round, turned 24 degrees, is 0.016 deep at 0.262."}],"note":"Each floor faces out and toward its own side. Read on the top-left pocket's hole, seen at the side view's edge: a round hole shows as an ellipse whose width over its height is the cosine of the angle between the floor and the line of sight."},"pocket_rear_x":{"label":"Pockets, rear end (the round end's farthest point, from the rear face)","kind":"length","measurements":[{"id":"below","value":0.347,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/surefire-procomp-556 aa48bc88d85b (Primary Arms PROCOMP556-1-2-28_02: the device standing muzzle up, square on its underside, from about 3 degrees above, 2200 x 1467)","scaleRef":"its length between the end faces' centres, 1224 px, as overall_length (2.5): 489.6 px/in; across the device, its collar's width (411 px) as od (0.864)","method":"the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges as read on those runs (± 3 px), stations from the rear face's centre (row 1369)","via":"harvest"},"note":"Row 1199, both bottom pockets. The side view sees the bottom-left one's floor end at row 1200 (0.394) from its edge."}],"note":"Behind the grooves, in the collar."},"pocket_front_x":{"label":"Pockets, front end (the round end's farthest point)","kind":"length","measurements":[{"id":"below","value":2.245,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/surefire-procomp-556 aa48bc88d85b (Primary Arms PROCOMP556-1-2-28_02: the device standing muzzle up, square on its underside, from about 3 degrees above, 2200 x 1467)","scaleRef":"its length between the end faces' centres, 1224 px, as overall_length (2.5): 489.6 px/in; across the device, its collar's width (411 px) as od (0.864)","method":"the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges as read on those runs (± 3 px), stations from the rear face's centre (row 1369)","via":"harvest"},"note":"Row 270: the round ends' tops, 0.255 behind the front face."}]},"pilot_hole_d":{"label":"Blind pilot holes at 3 and 9 o'clock, diameter","kind":"length","measurements":[{"id":"side","value":0.103,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/surefire-procomp-556 df201d3f2cee (Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467)","scaleRef":"its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864)","method":"the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)","via":"harvest"},"note":"The 9 o'clock one: rows 905 to 957 (52 px) on a collar 438 across."}],"note":"SureFire, as Piasa Armory, Midwest Gun Works and others reprint it: \"Every ProComp features blind pilot holes at the 9 o’clock position to enable fine-tuning of recoil traits for individual shooting styles or ammunition characteristics. All that is required is a basic hand drill and appropriate drill bits.\" Primary Arms: \"Blind pilot holes at the 3 and 9-o’clock positions\". One shows on the left port face in _03 and on SureFire's picture of it on a rifle, one on the right in Primary Arms' _00."},"pilot_hole_x":{"label":"Pilot holes, their middle (from the rear face)","kind":"length","measurements":[{"id":"side","value":0.917,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/surefire-procomp-556 df201d3f2cee (Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467)","scaleRef":"its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864)","method":"the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)","via":"harvest"},"note":"Row 931: behind the port flats, on the round between them and the grooves. The 3 o'clock one is drawn at the same station: Primary Arms' _00 shows it there to within its three-quarter view's reading."}]},"pilot_hole_depth":{"label":"Pilot holes, how deep (blind)","kind":"length","measurements":[{"id":"assumed","value":0.04,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows how deep a blind pilot hole goes. A spot drill's depth, short of the thread's major diameter.","via":"harvest"}}],"note":"NOT SOURCED: \"blind\" is the maker's word; no view looks into one."},"top_hole_d":{"label":"Holes in the two top pockets, diameter","kind":"length","measurements":[{"id":"side","value":0.124,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/surefire-procomp-556 df201d3f2cee (Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467)","scaleRef":"its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864)","method":"the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)","via":"harvest"},"note":"The top-left pocket's, seen at the side view's edge: 63 px along the device (rows 875 to 938), its true diameter there."}],"note":"One in each top pocket (counted on Primary Arms' _00 and _01, Rifle Supply's two photographs and SureFire's catalogue picture); none in the bottom pockets (_02, square on)."},"top_left_hole_x":{"label":"Top-left pocket's hole, its middle (from the rear face)","kind":"length","measurements":[{"id":"side","value":0.965,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/surefire-procomp-556 df201d3f2cee (Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467)","scaleRef":"its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864)","method":"the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)","via":"harvest"},"note":"Row 906, 0.048 ahead of the 9 o'clock pilot hole."}]},"top_right_hole_x":{"label":"Top-right pocket's hole, its middle (from the rear face)","kind":"length","measurements":[{"id":"patent","value":0.965,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{.top_left_hole_x}","basis":"US 7,954,414 (SureFire; listed against PROCOMP on its patent-marking page, https://www.surefire.com/product-education/suppressor-patents/), FIG. 4: the two top ports at one station along the body. The left one's station is read square on (top_left_hole_x).","via":"harvest"}},{"id":"oblique","value":0.887,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/surefire-procomp-556 1e487acfc1e8 (Primary Arms PROCOMP556-1-2-28_00: lying, front three-quarter from above its right side, 2200 x 1467)","scaleRef":"its own length along the axis in the picture as overall_length (2.5): about 611 px/in","method":"the holes' middles (picked on a crop at 1:1, ± 5 px) projected on the axis from the rear face's middle to the front face's: the right pocket's hole 0.03 behind the 3 o'clock pilot hole (taken at pilot_hole_x) and 0.13 behind the left pocket's","via":"harvest"},"note":"A three-quarter view sees two holes at different angles round the top as standing at different places along it: the 0.13 between them here is that, not a station's difference, if the patent's FIG. 4 holds for this product."}],"adopt":{"from":"patent","reason":"The maker's patent for this product draws the two ports at one station, and the one straight reading on file (the left one's) gives it. The oblique reading stays: a three-quarter view mixes an offset round the top into the stations along it."},"note":"No straight view on file faces it. SureFire's patent-marking page lists US 7,954,414 and 8,205,538 against PROCOMP; the first draws its two top ports at one station (FIG. 4, ports 36 and 38; FIG. 7 the section through both) and says of them: \"A first port may be offset from and to one side of the top of the body, and a second port offset from and to the opposite side of the top of the body by a transverse distance greater than the transverse distance by which the first port is offset\" (column 2). That is SureFire's \"offset porting\": offset round the top, not along it."},"chamber_d":{"label":"First chamber (between the thread and the rear window), diameter, as drawn","kind":"length","measurements":[{"id":"as-thread","value":0.4551,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.thread_minor_d}","basis":"An assumption for the drawing, not a reading of this part: the patent's FIG. 6 draws chamber 32 as the threaded bore carried on at about its minor diameter (200 px against the thread's crests' 230 px, on a body 445 px across; the figure isn't to scale: its bullet passage is drawn narrower than a bullet).","via":"harvest"}}],"note":"SureFire's patent for it (US 7,954,414, which its marking page lists against PROCOMP): \"a high pressure first chamber in the body extending along the axial passageway for receiving combustion gases from the muzzle\", which \"includes at least one port for venting a portion of the gases in the first chamber to directionally counter upward and sideward movement of the muzzle\" (column 1 and 2): the top ports vent it. FIG. 6 draws it (32) about as wide as the threaded bore's minor diameter. No view on file looks into it: NOT SOURCED as a size."},"chamber_front_x":{"label":"First chamber, front end (where it turns down to the bore; from the rear face), as drawn","kind":"length","measurements":[{"id":"as-patent","value":1.006,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{.window_rear_rear_x} - 0.157 * {.od}","basis":"An assumption for the drawing, not a reading: US 7,954,414 FIG. 6 has 70 px from the chamber's front end to the first window (a cone of 30 px, a wall of 40 px) on a body 445 px across: 0.157 of the diameter.","via":"harvest"}}],"note":"NOT SOURCED as a size: the patent's FIG. 6 has the chamber end in a cone, and then a wall with the bullet's passage through it, ahead of which the first window opens. Drawn by that figure's proportions from the rear window's rear edge."},"chamber_cone":{"label":"First chamber, the cone at its front end, length along the device, as drawn","kind":"length","measurements":[{"id":"as-patent","value":0.058,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"0.067 * {.od}","basis":"An assumption for the drawing, not a reading: the cone in US 7,954,414 FIG. 6 is 30 px long on a body 445 px across.","via":"harvest"}}]},"pin_hole_d":{"label":"Pin-and-weld pilot hole at 6 o'clock, diameter","kind":"length","measurements":[{"id":"below","value":0.088,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/surefire-procomp-556 aa48bc88d85b (Primary Arms PROCOMP556-1-2-28_02: the device standing muzzle up, square on its underside, from about 3 degrees above, 2200 x 1467)","scaleRef":"its length between the end faces' centres, 1224 px, as overall_length (2.5): 489.6 px/in; across the device, its collar's width (411 px) as od (0.864)","method":"the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges as read on those runs (± 3 px), stations from the rear face's centre (row 1369)","via":"harvest"},"note":"Rows 1238 to 1280 (42 px) on a collar 411 across."}],"note":"SureFire, as Piasa Armory reprints it: \"Pilot hole located at 6 o’clock for pin-and-weld applications\"; Primary Arms: \"an additional pilot hole at the 6-o’clock allows indexing the adapter at bottom dead center\"."},"pin_hole_x":{"label":"Pin-and-weld hole, its middle (from the rear face)","kind":"length","measurements":[{"id":"below","value":0.225,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/surefire-procomp-556 aa48bc88d85b (Primary Arms PROCOMP556-1-2-28_02: the device standing muzzle up, square on its underside, from about 3 degrees above, 2200 x 1467)","scaleRef":"its length between the end faces' centres, 1224 px, as overall_length (2.5): 489.6 px/in; across the device, its collar's width (411 px) as od (0.864)","method":"the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges as read on those runs (± 3 px), stations from the rear face's centre (row 1369)","via":"harvest"},"note":"Row 1259, on the land's line, in the collar behind the grooves and the pockets' round ends."}]},"thread_major_d":{"label":"The thread it is cut for: major diameter","kind":"length","measurements":[{"id":"tdp","value":0.4957,"unit":"in","pm":0.0033,"stated":"1/2-28 UNEF-2A MAJOR DIA .4989/.4924","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213","via":"user"}}],"note":"Its number names its thread: PROCOMP-556-1/2-28 (Redcon1: \"Thread: 1/2 x 28 TPI\"; Primary Arms: \"Thread Pattern 1/2 X 28\"). The Army barrel's 1/2-28, as the catalog's barrels are drawn."},"thread_minor_d":{"label":"The thread it is cut for: minor diameter","kind":"length","measurements":[{"id":"tdp","value":0.4551,"unit":"in","pm":0.002,"stated":"MINOR DIA .4551 MAX","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213","via":"user"}}]},"thread_pitch":{"label":"The thread it is cut for: pitch","kind":"length","measurements":[{"id":"tdp","value":0.03571,"unit":"in","pm":0.00005,"stated":"1/2-28 UNEF-2A","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213","via":"user"}}]},"thread_depth":{"label":"Threaded hole's depth from the rear face, as drawn","kind":"length","measurements":[{"id":"as-a2","value":0.69,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{a2-flash-hider.thread_depth}","basis":"An assumption for the drawing, not a reading: the depth of the Army compensator's threaded bore (drawing 9349051).","via":"user"}}],"note":"NOT SOURCED for this device: no page, drawing or photo on file shows how deep its thread goes. Drawn as deep as the Army compensator's, which the same barrels take: it then ends 0.23 behind the pilot holes."},"bore_d":{"label":"Hole through the device ahead of the thread, as drawn","kind":"length","measurements":[{"id":"as-3-prong","value":0.244,"unit":"in","pm":0.008,"source":{"type":"derived","expr":"{surefire-socom-3-prong.bore_d}","basis":"An assumption for the drawing, not a reading of this part.","via":"harvest"}}],"note":"NOT SOURCED for this device: the photos on file show the front face's hole only at a slant, where its far wall hides its edge. Drawn as the 3-prong's, the same maker's device for the same bullet."},"thread_length":{"label":"Barrel thread length it takes, or is made for","kind":"length","measurements":[],"note":"No source states it (no drawing, no manual on file): no thread_length on its interface."}}},{"subject":"surefire-scout-light-pro-dual-fuel","title":"SureFire Scout Light Pro Dual Fuel (M640DF-BK-PRO, M640DF-TN-PRO)","dimensions":{"weight":{"label":"Weight (say with which batteries, and whether the mount is in it)","kind":"mass","measurements":[{"id":"surefire","value":5.5,"unit":"oz","pm":0.05,"stated":"WEIGHT W/ BATTERIES 5.5 oz (156 g)","source":{"type":"spec","publisher":"manufacturer","name":"SureFire, Scout Light Pro Dual Fuel, specifications (Body)","url":"https://www.surefire.com/scout-light-pro-dual-fuel/","retrieved":"2026-10-05","via":"harvest"}}],"note":"SureFire says \"w/ batteries\" and no more: which batteries (one SF18650, which comes with it, or two 123A) and whether a mount is counted aren't stated on its page. Each mount sold apart is 1.6 oz (.rail_mount_weight, .mlok_mount_weight). Retailers repeat the 5.5 oz."},"length":{"label":"Overall length","kind":"length","measurements":[{"id":"surefire","value":5.56,"unit":"in","pm":0.005,"stated":"LENGTH 5.56 in (14.1 cm)","source":{"type":"spec","publisher":"manufacturer","name":"SureFire, Scout Light Pro Dual Fuel, specifications (Body)","url":"https://www.surefire.com/scout-light-pro-dual-fuel/","retrieved":"2026-10-05","via":"harvest"}}],"note":"Taken as the bezel's front to the tail cap's rear rim, along the axis: the photos' proportions bear that reading out (.head_diameter). Midwest Gun Works, Sportsman's Warehouse and T.REX ARMS repeat it."},"head_diameter":{"label":"Head (bezel) diameter","kind":"length","measurements":[{"id":"surefire","value":1.125,"unit":"in","pm":0.0005,"stated":"BEZEL DIAMETER 1.125 in (2.9 cm)","source":{"type":"spec","publisher":"manufacturer","name":"SureFire, Scout Light Pro Dual Fuel, specifications (Body)","url":"https://www.surefire.com/scout-light-pro-dual-fuel/","retrieved":"2026-10-05","via":"harvest"}}],"note":"Taken as the bezel's smooth front section (the length of the head ahead of its faceted ring), not the ring, which is wider (.ring_diameter). Tried against the published length on three side photos, the lit edges kept: on Rifle Supply's (5911a4468ee0), with heights by this diameter and each end face taken behind its rim's arc, the faces stand 5.518 in apart, 0.8% short of the published 5.56 (the trace's own check: it stops past 2%). End to end with no correction the silhouettes read 5.627 in there, 5.740 on SureFire's left profile (240f795d3e2a) and 5.777 on Primary Arms' photograph (5aa1d5cc4968): 1 to 4% long, as near rims standing toward a close lens make them. Read as the ring instead (1.05 of this section in all three), the two published sizes would be 4 to 6% apart on every photo."},"body_diameter":{"label":"Body diameter","kind":"length","measurements":[{"id":"riflesupply","value":0.843,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/surefire-scout-light-pro-dual-fuel 5911a4468ee0 (Rifle Supply's gallery, SFM640DF-BK-PRO_2_HR: the body alone, straight side view on white, 2000 x 2000)","scaleRef":"the bezel's front section in the same photo as .head_diameter (1.125 in over 0.86 to 0.96 of the length: 199.92 px radius)","method":"tools/turned.py --dark-above 235: median radius over 0.41 to 0.635 of the length, both edges (149.82 px, ratio 0.7494 of the bezel's); ± the two sections' scatter and half a pixel an edge","via":"harvest"}},{"id":"surefire-left","value":0.845,"unit":"in","pm":0.007,"source":{"type":"photo","photo":"references/surefire-scout-light-pro-dual-fuel 240f795d3e2a (SureFire's gallery, M640DF-BK-PRO-profileL: the light on its Picatinny mount, left side, on white, 1500 x 1500)","scaleRef":"the bezel's front section in the same photo as .head_diameter (146.99 px radius)","method":"tools/turned.py --dark-above 235 --flip: median radius over 0.43 to 0.6 of the length, both edges (110.42 px, ratio 0.7512)","via":"harvest"}},{"id":"primaryarms","value":0.853,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/surefire-scout-light-pro-dual-fuel 5aa1d5cc4968 (Primary Arms' own photograph, M640DF-BK-PRO_01: the body without a mount, side view on white, 2200 x 1467)","scaleRef":"the bezel's front section in the same photo as .head_diameter (178.00 px radius)","method":"tools/turned.py --dark-above 235: median radius over 0.43 to 0.635 of the length, both edges (134.91 px, ratio 0.7579); the photo leans 1.5 degrees, taken out by the fitted axis","via":"harvest"}}],"adopt":{"from":"riflesupply","reason":"The largest and sharpest of the three, and the photo the outline is traced from. SureFire's newer profile agrees within 0.002 in; Primary Arms' own photograph of a unit reads 0.010 more, inside the two ±."},"note":"Not published. The tube between the head and the body's bands, by its ratio to the bezel in three side photos (tools/turned.py at level 235: ratios of radii are true whatever the lens's distance). 0.845 in is 21.5 mm: 1.4 mm of wall round an 18.6 mm cell."},"tailcap_diameter":{"label":"Tail cap's shroud diameter","kind":"length","measurements":[{"id":"riflesupply","value":0.989,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/surefire-scout-light-pro-dual-fuel 5911a4468ee0 (Rifle Supply's gallery, SFM640DF-BK-PRO_2_HR: the body alone, straight side view on white, 2000 x 2000)","scaleRef":"the bezel's front section in the same photo as .head_diameter (199.92 px radius)","method":"tools/turned.py --dark-above 235: median radius over 0.012 to 0.058 of the length, both edges (175.77 px, ratio 0.8792)","via":"harvest"}},{"id":"surefire-left","value":0.995,"unit":"in","pm":0.007,"source":{"type":"photo","photo":"references/surefire-scout-light-pro-dual-fuel 240f795d3e2a (SureFire's gallery, M640DF-BK-PRO-profileL: the light on its Picatinny mount, left side, on white, 1500 x 1500)","scaleRef":"the bezel's front section in the same photo as .head_diameter (146.99 px radius)","method":"tools/turned.py --dark-above 235 --flip: median radius over 0.02 to 0.058 of the length, top edge (130.04 px, ratio 0.8847)","via":"harvest"}},{"id":"primaryarms","value":0.983,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/surefire-scout-light-pro-dual-fuel 5aa1d5cc4968 (Primary Arms' own photograph, M640DF-BK-PRO_01: the body without a mount, side view on white, 2200 x 1467)","scaleRef":"the bezel's front section in the same photo as .head_diameter (178.00 px radius)","method":"tools/turned.py --dark-above 235: median radius over 0.02 to 0.058 of the length, top edge (155.56 px, ratio 0.8739)","via":"harvest"}}],"adopt":{"from":"riflesupply","reason":"The photo the outline is traced from; the other two read 0.006 either side of it."},"note":"Not published. The Z68 tail cap's rear shroud, by its ratio to the bezel: what the trace takes the rear end face's rim to be."},"axis_above_mount":{"label":"The body's axis above the mounting face (the rail's top, the handguard's face)","kind":"length","measurements":[{"id":"hook","value":0.19,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/surefire-scout-light-pro-dual-fuel 0e24c7f67668 (SureFire's M-1913-S page, M-1913-S-TN_isoL: the Picatinny mount alone in tan, three-quarter view, 1500 x 1500)","scaleRef":"the pivot barrel's end face in the same photo, 208 px across where it is 415 px tall: its diameter is .ear_bottom_below_axis less .pivot_top_below_axis (0.360 in)","method":"the fixed hook's V, in the barrel's own end plane: its apex (column 355) 139 px from the barrel's centre (494), 0.668 of the barrel's diameter (0.236 in: .rail_corner_below_pivot), and its upper wall running 28 px (0.05 in) toward the plate before the end face turns away: 0.236 less 0.05; by hand. ± covers the readings and that the wall's run is a least figure for a rail's corner","via":"harvest"}}],"note":"For the Picatinny mount on a rail as SureFire photographs it (hanging straight from its pivot): the body then stands BESIDE the rail, 1.12 in from its centre line (.rail_centre_below_axis), and this is how far its axis, and the pivot's, stand above the rail's top. The clamp holds a rail by its two corners (a V in each jaw) and its plate rides clear of the rail's top, so the rail's top is its corner's height (.rail_corner_below_pivot) less how far a rail's corner lies below its top. That last figure is MIL-STD-1913's and isn't on file: the hook's wall above the corner runs 0.05 in in the photo, which is the least it can be, so this is the most the axis can stand above the rail (with a deeper corner, less: about 0.06 in less if the corner is 0.11 in down). On the M-LOK mount, as photographed, the body stands over the face instead: .mlok_pivot_above_face plus the pivot's distance below the axis."},"rail_corner_below_pivot":{"label":"A rail's corner (the fixed hook's V) below the pivot's axis, across the Picatinny mount","kind":"length","measurements":[{"id":"surefire-tan","value":0.236,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/surefire-scout-light-pro-dual-fuel 0e24c7f67668 (SureFire's M-1913-S page, M-1913-S-TN_isoL: the Picatinny mount alone in tan, three-quarter view, 1500 x 1500)","scaleRef":"the pivot barrel's end face in the same photo, 208 px across (0.360 in)","method":"the V's apex at column 355 against the barrel's centre at 494, both in the barrel's end plane: 139 px, 0.668 of its diameter; by hand","via":"harvest"}}],"note":"Where the clamp holds the rail's near corner, measured out of the plate (toward the rail). Along the plate the same V is 0.05 in from the pivot's axis, which with a rail's 0.835 in puts the rail's centre line where the two jaws' lips have it in the right profile (.rail_centre_below_axis)."},"recoil_bar_width":{"label":"Width of the recoil bar under the Picatinny mount's plate (along the rail)","kind":"length","measurements":[{"id":"surefire-right","value":0.2,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/surefire-scout-light-pro-dual-fuel 7a7e18571e8e (SureFire's gallery, M640DF-BK-PRO-profileR: the light on its Picatinny mount, right side, the mount's rail side toward the lens, 1500 x 1500)","scaleRef":"the body's two bands either side of the mount in the same photo, .band_rear_x and .band_front_x apart: 266.7 px/in there","method":"the bar's two edges across six rows (860 to 960): columns 423 and 476.5, 53.5 px; by hand on the pixel values","via":"harvest"}}],"note":"The bar that sits in a rail's slot: it has to be narrower than the slot (std.picatinny.slot_width, 0.206 in), and reads just that. It is also what says the right profile's scale is right: by the bezel's published diameter read at the old threshold it came out 0.225 in, wider than any slot."},"width":{"label":"Overall width (with its mount and switch)","kind":"length","measurements":[],"note":"Not published, and it changes as the mount is swivelled."},"lugs":{"label":"M-LOK slots its mount's lugs span","kind":"count","measurements":[{"id":"photo","value":1,"unit":"count","source":{"type":"photo","photo":"references/surefire-scout-light-pro-dual-fuel 1d17a4f4ffe3 (SureFire's M-MLOK-S page, M-MLOK-S-BK_isoL: the M-LOK mount alone from above, 1500 x 1500)","scaleRef":"the mount's pivot barrel, 0.553 in long by the left profile photo","method":"the two screws stand 1.16 barrel lengths apart (0.64 in; three photos): well under a 32 mm slot's length, and far from the 40 mm between two slots","via":"harvest"}}],"note":"No page on file states it, and the sheet SureFire is said to enclose (Magpul's) isn't on file. Worked out from the mount's photos: two screws with T-nuts about 0.64 in apart (.mlok_screw_spacing) on a base about 1.04 in long: both nuts go in one 32 mm slot."},"reach_inside":{"label":"Reach inside the handguard (below the mounting face, tightened)","kind":"length","measurements":[],"note":"Not sourced: no page on file gives the M-MLOK-S's nuts a figure, and the Magpul sheet SureFire's box is said to enclose isn't on file."},"rail_mount_weight":{"label":"Weight of the Picatinny mount sold apart (M-1913-S)","kind":"mass","measurements":[{"id":"surefire","value":1.6,"unit":"oz","pm":0.05,"stated":"WEIGHT 1.6 oz (45 g)","source":{"type":"spec","publisher":"manufacturer","name":"SureFire, M-1913-S-BK Scout Light Pro Picatinny Mount, Key Attributes","url":"https://www.surefire.com/m-1913-s-bk-scout-light-pro-picatinny-mount/","retrieved":"2026-10-05","via":"harvest"}}],"note":"Whether the light's 5.5 oz counts a mount isn't stated."},"mlok_mount_weight":{"label":"Weight of the M-LOK mount sold apart (M-MLOK-S)","kind":"mass","measurements":[{"id":"surefire","value":1.6,"unit":"oz","pm":0.05,"stated":"WEIGHT 1.6 oz (45 g)","source":{"type":"spec","publisher":"manufacturer","name":"SureFire, M-MLOK-S Scout Light Pro M-Lok Mount, Key Attributes","url":"https://www.surefire.com/m-mlok-s-scout-light-pro-m-lok-mount/","retrieved":"2026-10-05","via":"harvest"}}],"note":"The same figure as the Picatinny mount's, on a page of the same template: it may be one figure given to both."},"rear_face_x":{"label":"Rear end face, ahead of the outline's rearmost point","kind":"length","measurements":[{"id":"riflesupply","value":0.044,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/surefire-scout-light-pro-dual-fuel 5911a4468ee0 (Rifle Supply's gallery, SFM640DF-BK-PRO_2_HR: the body alone, straight side view on white, 2000 x 2000)","scaleRef":"scale from surefire-scout-light-pro-dual-fuel.head_diameter = 1.125 in, the tube's own width column by column: 399.4 px over columns 1708–1752, 399.6 px over columns 1918–1955; a line through them (rms 0.27 px) changes +0.1% from column 1708 to 1955, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1000)/width, the lens's axis taken to meet the image at column 1000; 354.2 px/in there. The axis is the tube's centre line (tilt -0.20°, rms 0.06 px). Lengths then scaled by 1.0076 so that the end faces are surefire-scout-light-pro-dual-fuel.length = 5.56 in apart: at the tube's scale they read 5.518 (-0.8%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.070 in over radius 0.563 (rms 0.014), the rear end's rim sags 0.043 in over radius 0.494 (rms 0.001)","method":"the min end's face: the silhouette's tip at -0.000 less its rim's arc, 0.044 in of sag at radius 0.4945 (the end is seen from 5.0° off square; arc fitted over 109 rows, rms 0.001) of the traced outline (tools/trace.py); the tail cap's rear face behind its rim's arc: the front face is the published length ahead of it","via":"harvest"}}],"note":"The side photo sees the tail cap's rear rim from an angle: the outline's rearmost point is the rim's near side, and the face is this far ahead of it. The front face is the published length ahead of the rear one."},"band_diameter":{"label":"Diameter of the body's two bands","kind":"length","measurements":[{"id":"riflesupply","value":0.889,"unit":"in","pm":0.009,"source":{"type":"photo","photo":"references/surefire-scout-light-pro-dual-fuel 5911a4468ee0 (Rifle Supply's gallery, SFM640DF-BK-PRO_2_HR: the body alone, straight side view on white, 2000 x 2000)","scaleRef":"scale from surefire-scout-light-pro-dual-fuel.head_diameter = 1.125 in, the tube's own width column by column: 399.4 px over columns 1708–1752, 399.6 px over columns 1918–1955; a line through them (rms 0.27 px) changes +0.1% from column 1708 to 1955, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1000)/width, the lens's axis taken to meet the image at column 1000; 354.2 px/in there. The axis is the tube's centre line (tilt -0.20°, rms 0.06 px). Lengths then scaled by 1.0076 so that the end faces are surefire-scout-light-pro-dual-fuel.length = 5.56 in apart: at the tube's scale they read 5.518 (-0.8%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.070 in over radius 0.563 (rms 0.014), the rear end's rim sags 0.043 in over radius 0.494 (rms 0.001)","method":"height (tooth tops, max over 0.05 in windows) along x [1.12, 1.36] of the traced outline (tools/trace.py); the rear band","via":"harvest"}}],"note":"Not published. The rear band (the middle one reads the same); the pivot's two ears hang under them."},"ring_diameter":{"label":"Diameter of the faceted ring behind the bezel (as seen)","kind":"length","measurements":[{"id":"riflesupply","value":1.178,"unit":"in","pm":0.009,"source":{"type":"photo","photo":"references/surefire-scout-light-pro-dual-fuel 5911a4468ee0 (Rifle Supply's gallery, SFM640DF-BK-PRO_2_HR: the body alone, straight side view on white, 2000 x 2000)","scaleRef":"scale from surefire-scout-light-pro-dual-fuel.head_diameter = 1.125 in, the tube's own width column by column: 399.4 px over columns 1708–1752, 399.6 px over columns 1918–1955; a line through them (rms 0.27 px) changes +0.1% from column 1708 to 1955, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1000)/width, the lens's axis taken to meet the image at column 1000; 354.2 px/in there. The axis is the tube's centre line (tilt -0.20°, rms 0.06 px). Lengths then scaled by 1.0076 so that the end faces are surefire-scout-light-pro-dual-fuel.length = 5.56 in apart: at the tube's scale they read 5.518 (-0.8%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.070 in over radius 0.563 (rms 0.014), the rear end's rim sags 0.043 in over radius 0.494 (rms 0.001)","method":"height (tooth tops, max over 0.05 in windows) along x [4.5, 4.78] of the traced outline (tools/trace.py); the faceted ring behind the bezel, as this view happens to see its flats","via":"harvest"}}],"note":"Not published. The ring has flats, so a side view reads it between its flats and its corners, by how the head happens to be turned: 1.180 by its ratio to the bezel in Rifle Supply's photo, 1.183 in SureFire's left profile, 1.186 in Primary Arms' photograph. Wider than the published bezel diameter, which is the smooth section ahead of it (.head_diameter)."},"band_rear_x":{"label":"Rear band's rear edge, ahead of the outline's rearmost point","kind":"length","measurements":[{"id":"riflesupply","value":1.078,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/surefire-scout-light-pro-dual-fuel 5911a4468ee0 (Rifle Supply's gallery, SFM640DF-BK-PRO_2_HR: the body alone, straight side view on white, 2000 x 2000)","scaleRef":"scale from surefire-scout-light-pro-dual-fuel.head_diameter = 1.125 in, the tube's own width column by column: 399.4 px over columns 1708–1752, 399.6 px over columns 1918–1955; a line through them (rms 0.27 px) changes +0.1% from column 1708 to 1955, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1000)/width, the lens's axis taken to meet the image at column 1000; 354.2 px/in there. The axis is the tube's centre line (tilt -0.20°, rms 0.06 px). Lengths then scaled by 1.0076 so that the end faces are surefire-scout-light-pro-dual-fuel.length = 5.56 in apart: at the tube's scale they read 5.518 (-0.8%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.070 in over radius 0.563 (rms 0.014), the rear end's rim sags 0.043 in over radius 0.494 (rms 0.001)","method":"x_min in x [0.95, 1.25] in y [0.437, 0.443] of the traced outline (tools/trace.py); the rear band's rear edge, where the top edge crosses 0.44 in off the axis","via":"harvest"}}],"note":"A step the other side photos are placed by."},"band_front_x":{"label":"Middle band's front edge, ahead of the outline's rearmost point","kind":"length","measurements":[{"id":"riflesupply","value":2.319,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/surefire-scout-light-pro-dual-fuel 5911a4468ee0 (Rifle Supply's gallery, SFM640DF-BK-PRO_2_HR: the body alone, straight side view on white, 2000 x 2000)","scaleRef":"scale from surefire-scout-light-pro-dual-fuel.head_diameter = 1.125 in, the tube's own width column by column: 399.4 px over columns 1708–1752, 399.6 px over columns 1918–1955; a line through them (rms 0.27 px) changes +0.1% from column 1708 to 1955, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1000)/width, the lens's axis taken to meet the image at column 1000; 354.2 px/in there. The axis is the tube's centre line (tilt -0.20°, rms 0.06 px). Lengths then scaled by 1.0076 so that the end faces are surefire-scout-light-pro-dual-fuel.length = 5.56 in apart: at the tube's scale they read 5.518 (-0.8%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.070 in over radius 0.563 (rms 0.014), the rear end's rim sags 0.043 in over radius 0.494 (rms 0.001)","method":"x_max in x [2.0, 2.6] in y [0.437, 0.443] of the traced outline (tools/trace.py); the middle band's front edge, where the top edge crosses 0.44 in off the axis","via":"harvest"}}],"note":"A step the other side photos are placed by."},"head_step_x":{"label":"Step at the head's rear, ahead of the outline's rearmost point","kind":"length","measurements":[{"id":"riflesupply","value":3.699,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/surefire-scout-light-pro-dual-fuel 5911a4468ee0 (Rifle Supply's gallery, SFM640DF-BK-PRO_2_HR: the body alone, straight side view on white, 2000 x 2000)","scaleRef":"scale from surefire-scout-light-pro-dual-fuel.head_diameter = 1.125 in, the tube's own width column by column: 399.4 px over columns 1708–1752, 399.6 px over columns 1918–1955; a line through them (rms 0.27 px) changes +0.1% from column 1708 to 1955, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1000)/width, the lens's axis taken to meet the image at column 1000; 354.2 px/in there. The axis is the tube's centre line (tilt -0.20°, rms 0.06 px). Lengths then scaled by 1.0076 so that the end faces are surefire-scout-light-pro-dual-fuel.length = 5.56 in apart: at the tube's scale they read 5.518 (-0.8%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.070 in over radius 0.563 (rms 0.014), the rear end's rim sags 0.043 in over radius 0.494 (rms 0.001)","method":"x_min in x [3.5, 3.9] in y [0.5045, 0.5105] of the traced outline (tools/trace.py); the step at the head's rear, where the top edge crosses 0.5075 in off the axis","via":"harvest"}}],"note":"A step the other side photos are placed by."},"bezel_rear_x":{"label":"Where the bezel's smooth front section begins, ahead of the outline's rearmost point","kind":"length","measurements":[{"id":"riflesupply","value":4.791,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/surefire-scout-light-pro-dual-fuel 5911a4468ee0 (Rifle Supply's gallery, SFM640DF-BK-PRO_2_HR: the body alone, straight side view on white, 2000 x 2000)","scaleRef":"scale from surefire-scout-light-pro-dual-fuel.head_diameter = 1.125 in, the tube's own width column by column: 399.4 px over columns 1708–1752, 399.6 px over columns 1918–1955; a line through them (rms 0.27 px) changes +0.1% from column 1708 to 1955, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1000)/width, the lens's axis taken to meet the image at column 1000; 354.2 px/in there. The axis is the tube's centre line (tilt -0.20°, rms 0.06 px). Lengths then scaled by 1.0076 so that the end faces are surefire-scout-light-pro-dual-fuel.length = 5.56 in apart: at the tube's scale they read 5.518 (-0.8%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.070 in over radius 0.563 (rms 0.014), the rear end's rim sags 0.043 in over radius 0.494 (rms 0.001)","method":"x_min in x [4.7, 4.95] in y [0.567, 0.573] of the traced outline (tools/trace.py); where the bezel's smooth front section begins ahead of its ring: the top edge coming down through 0.57 in off the axis","via":"harvest"}}],"note":"A step the other side photos are placed by: the corner where the bezel's diameter is the published one."},"pivot_top_below_axis":{"label":"Top of the mount's barrel, below the body's axis","kind":"length","measurements":[{"id":"surefire-left","value":0.471,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/surefire-scout-light-pro-dual-fuel 240f795d3e2a (SureFire's gallery, M640DF-BK-PRO-profileL: the light on its Picatinny mount, left side, on white, 1500 x 1500)","scaleRef":"frame from the reviewed holes band_rear, band_front, head_step, bezel_rear (260.7 px/in, rms 0.003 in over 4 points)","method":"−y_max of the traced outline (tools/trace.py); the top of the mount's barrel, under the white gap between it and the tube","via":"harvest"}}],"note":"The barrel the mount turns on sits just clear of the tube: a gap of 0.04 in shows between them. With the ears' lowest point (.ear_bottom_below_axis) it gives the pivot: its axis midway between the two, the barrel's diameter their difference."},"ear_bottom_below_axis":{"label":"Lowest point of the pivot's ears, below the body's axis","kind":"length","measurements":[{"id":"surefire-left","value":0.831,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/surefire-scout-light-pro-dual-fuel 240f795d3e2a (SureFire's gallery, M640DF-BK-PRO-profileL: the light on its Picatinny mount, left side, on white, 1500 x 1500)","scaleRef":"frame from the reviewed holes band_rear, band_front, head_step, bezel_rear (260.7 px/in, rms 0.003 in over 4 points)","method":"−y_min in x [1.95, 2.13] of the traced outline (tools/trace.py); the front ear's lowest point","via":"harvest"}}],"note":"The ears are round about the pivot and flush with the mount's barrel between them."},"barrel_rear_x":{"label":"Rear end of the mount's barrel, ahead of the outline's rearmost point","kind":"length","measurements":[{"id":"surefire-left","value":1.412,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/surefire-scout-light-pro-dual-fuel 240f795d3e2a (SureFire's gallery, M640DF-BK-PRO-profileL: the light on its Picatinny mount, left side, on white, 1500 x 1500)","scaleRef":"frame from the reviewed holes band_rear, band_front, head_step, bezel_rear (260.7 px/in, rms 0.003 in over 4 points)","method":"x_min in y [-0.75, -0.55] of the traced outline (tools/trace.py); the rear end of the mount's barrel, against the rear ear","via":"harvest"}}],"note":"The rear ear's front face."},"barrel_front_x":{"label":"Front end of the mount's barrel, ahead of the outline's rearmost point","kind":"length","measurements":[{"id":"surefire-left","value":1.965,"unit":"in","pm":0.007,"source":{"type":"photo","photo":"references/surefire-scout-light-pro-dual-fuel 240f795d3e2a (SureFire's gallery, M640DF-BK-PRO-profileL: the light on its Picatinny mount, left side, on white, 1500 x 1500)","scaleRef":"frame from the reviewed holes band_rear, band_front, head_step, bezel_rear (260.7 px/in, rms 0.003 in over 4 points)","method":"x_max in y [-0.75, -0.55] of the traced outline (tools/trace.py); the front end of the mount's barrel, against the front ear","via":"harvest"}}],"note":"The front ear's rear face."},"clamp_rear_x":{"label":"Rear edge of the Picatinny mount's plate, ahead of the outline's rearmost point","kind":"length","measurements":[{"id":"surefire-left","value":1.406,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/surefire-scout-light-pro-dual-fuel 240f795d3e2a (SureFire's gallery, M640DF-BK-PRO-profileL: the light on its Picatinny mount, left side, on white, 1500 x 1500)","scaleRef":"frame from the reviewed holes band_rear, band_front, head_step, bezel_rear (260.7 px/in, rms 0.003 in over 4 points)","method":"x_min in y [-1.5, -0.9] of the traced outline (tools/trace.py); the plate's rear edge, below the ears","via":"harvest"}}],"note":"With .clamp_front_x: how far the clamp reaches along the rail, and where its middle is on the body."},"clamp_front_x":{"label":"Front edge of the Picatinny mount's plate, ahead of the outline's rearmost point","kind":"length","measurements":[{"id":"surefire-left","value":1.999,"unit":"in","pm":0.007,"source":{"type":"photo","photo":"references/surefire-scout-light-pro-dual-fuel 240f795d3e2a (SureFire's gallery, M640DF-BK-PRO-profileL: the light on its Picatinny mount, left side, on white, 1500 x 1500)","scaleRef":"frame from the reviewed holes band_rear, band_front, head_step, bezel_rear (260.7 px/in, rms 0.003 in over 4 points)","method":"x_max in y [-1.5, -0.9] of the traced outline (tools/trace.py); the plate's front edge, below the ears","via":"harvest"}}]},"jaw_bottom_below_axis":{"label":"Underside of the Picatinny mount's moving jaw, below the body's axis","kind":"length","measurements":[{"id":"surefire-left","value":1.62,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/surefire-scout-light-pro-dual-fuel 240f795d3e2a (SureFire's gallery, M640DF-BK-PRO-profileL: the light on its Picatinny mount, left side, on white, 1500 x 1500)","scaleRef":"frame from the reviewed holes band_rear, band_front, head_step, bezel_rear (260.7 px/in, rms 0.003 in over 4 points)","method":"−y_min of the traced outline (tools/trace.py); the moving jaw's underside (the mount screw's head, 0.04 in proud of it, left out)","via":"harvest"}}],"note":"As SureFire photographs it, the mount hanging straight below the body."},"pivot_screw_head_front_x":{"label":"Front face of the pivot screw's head, ahead of the outline's rearmost point","kind":"length","measurements":[{"id":"surefire-left","value":2.325,"unit":"in","pm":0.007,"source":{"type":"photo","photo":"references/surefire-scout-light-pro-dual-fuel 240f795d3e2a (SureFire's gallery, M640DF-BK-PRO-profileL: the light on its Picatinny mount, left side, on white, 1500 x 1500)","scaleRef":"frame from the reviewed holes band_rear, band_front, head_step, bezel_rear (260.7 px/in, rms 0.003 in over 4 points)","method":"x_max of the traced outline (tools/trace.py); the pivot screw's head, its front face","via":"harvest"}}]},"rail_centre_below_axis":{"label":"The rail's centre line below the body's axis, the Picatinny mount hanging straight (as photographed)","kind":"length","measurements":[{"id":"surefire-right","value":1.123,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/surefire-scout-light-pro-dual-fuel 7a7e18571e8e (SureFire's gallery, M640DF-BK-PRO-profileR: the light on its Picatinny mount, right side, the mount's rail side toward the lens, 1500 x 1500)","scaleRef":"the body's two bands either side of the mount in the same photo: the rear band's rear edge (column 286.6) and the middle band's front edge (617.6), .band_rear_x and .band_front_x apart: 266.7 px/in there (the photo is yawed: its bezel reads 258.5)","method":"rows by hand on an 8x crop: the fixed hook's lip 809.5, the moving jaw's lip 991, the body's axis 600.8: 0.783 and 1.463 in below the axis, their middle 1.123; the jaw's underside at 1034 reads 1.624, against 1.620 in the left profile","via":"harvest"}}],"note":"Where the clamp holds a rail: midway between the fixed hook's lip and the moving jaw's, 0.680 in apart in the photo (a rail is 0.835 across its corners, so each lip reaches 0.08 in under one). The moving jaw may stand closer in the photo than on a rail. The fixed hook alone, by the tan mount's three-quarter photo (its V 0.05 in below the pivot's axis), puts it at 1.12."},"clamp_thickness":{"label":"Thickness of the Picatinny mount's plate (its SF face to its rail side)","kind":"length","measurements":[{"id":"surefire-tan","value":0.22,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/surefire-scout-light-pro-dual-fuel 0e24c7f67668 (SureFire's M-1913-S page, M-1913-S-TN_isoL: the Picatinny mount alone in tan, three-quarter view, 1500 x 1500)","scaleRef":"the pivot barrel's end face in the same photo, 208 px across where it is 415 px tall: its diameter is .ear_bottom_below_axis less .pivot_top_below_axis (0.360 in)","method":"the moving jaw's end face, 130 px across (columns 405 to 535 at rows 1150 to 1230), over the barrel end's 208 px: 0.625 of its diameter. A same-direction ratio in one end plane, by hand; the photo's perspective between the mount's two ends is in the ±","via":"harvest"}}],"note":"Coarse. The mount's own page shows it three-quarter on; the moving jaw's end face is read against the pivot barrel's end, both foreshortened alike, though they are an inch apart down the photo. The plate's SF face runs tangent into the barrel in both colours' photos; its other face rides clear of the rail's top (.axis_above_mount)."},"jaw_reach":{"label":"How far the Picatinny mount's jaws reach below the rail's top","kind":"length","measurements":[{"id":"surefire-tan","value":0.1,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/surefire-scout-light-pro-dual-fuel 0e24c7f67668 (SureFire's M-1913-S page, M-1913-S-TN_isoL: the Picatinny mount alone in tan, three-quarter view, 1500 x 1500)","scaleRef":"the pivot barrel's end face in the same photo, 208 px across (0.360 in)","method":"the jaw's hook tip at column 347 against its block's face at 405 (rows 1240 to 1300): 58 px, 0.279 of the barrel's diameter; by hand","via":"harvest"}}],"note":"Coarse: the moving jaw's hook beyond its block's rail-side face, in the same photo and by the same ratio. The fixed hook reads deeper (its outer face 0.19 in beyond the barrel's surface) and is drawn to the same reach."},"mlok_screw_spacing":{"label":"M-LOK mount: its two screws, centre to centre","kind":"length","measurements":[{"id":"photos","value":0.64,"unit":"in","pm":0.07,"source":{"type":"photo","photo":"references/surefire-scout-light-pro-dual-fuel 1d17a4f4ffe3 (SureFire's M-MLOK-S page, M-MLOK-S-BK_isoL: the M-LOK mount alone from above, 1500 x 1500); b01c13c9399c (SureFire's gallery, isoL_MLOK: the mount loose with the pivot screw through it); d0a349018d36 (Rifle Supply, _3_HR: the mount fitted, from below)","scaleRef":"the mount's pivot barrel, which lies along the screws' line: its length is .barrel_front_x less .barrel_rear_x (0.553 in, the gap between the body's ears)","method":"the screws' centres over the barrel's length, both read along the same direction in each photo, by hand: 759 px over 663 (1.145), 156 over 136 (1.15), 250 over 212 (1.18, the web's length standing in for the barrel's): 1.16 of the barrel's length. The first photo is close (its parallels converge 8 degrees)","via":"harvest"}}],"note":"Coarse, and short of the M-LOK interval (std.mlok.interval, 20 mm = 0.787 in) by more than its ±: either SureFire's nuts stand closer, or the three photos' perspective reads the same way. Either way both nuts go in one 32 mm slot (.lugs)."},"mlok_base_width":{"label":"M-LOK mount: width of its base","kind":"length","measurements":[{"id":"photos","value":0.4,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/surefire-scout-light-pro-dual-fuel 1d17a4f4ffe3 (SureFire's M-MLOK-S page, M-MLOK-S-BK_isoL: the M-LOK mount alone from above, 1500 x 1500)","scaleRef":"the two screws' centres in the same photo, 759 px apart (.mlok_screw_spacing)","method":"along the screws' line: the right counterbore 370 px across and the rim beyond it 50 px, so the base's end is 235 px from the screw: 0.62 of the spacing across; by hand","via":"harvest"}}],"note":"Coarse. The base is an obround whose ends are round about the screws: its length is taken as the screws' spacing plus this width."},"mlok_pivot_above_face":{"label":"M-LOK mount: the pivot's axis above its mounting face","kind":"length","measurements":[{"id":"photos","value":0.4,"unit":"in","pm":0.1,"source":{"type":"photo","photo":"references/surefire-scout-light-pro-dual-fuel d0a349018d36 (Rifle Supply's gallery, SFM640DF-BK-PRO_3_HR: the M-LOK mount fitted, from the front left and below, 2000 x 2000)","scaleRef":"the pivot screw's head in the same photo, 68 px tall (0.35 in across in the left profile)","method":"the head's centre to the base's upper face, 48 px, and the base about 30 px thick, both read up the photo, which looks up at the mount from below: foreshortened by an angle that isn't known, hence the ±","via":"harvest"}}],"note":"Very coarse: no photo on file shows the mount square on from its end."},"mlok_base_thickness":{"label":"M-LOK mount: thickness of its base","kind":"length","measurements":[{"id":"photos","value":0.15,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/surefire-scout-light-pro-dual-fuel d0a349018d36 (Rifle Supply's gallery, SFM640DF-BK-PRO_3_HR: the M-LOK mount fitted, from the front left and below, 2000 x 2000)","scaleRef":"the pivot screw's head in the same photo, 68 px tall (0.35 in across in the left profile)","method":"the base's edge about 30 px up the photo, against the head's 68 px; by hand, foreshortened by an angle that isn't known","via":"harvest"}}],"note":"Very coarse, read with .mlok_pivot_above_face."},"mlok_counterbore_diameter":{"label":"M-LOK mount: diameter of the counterbore round each screw","kind":"length","measurements":[{"id":"photos","value":0.31,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/surefire-scout-light-pro-dual-fuel 1d17a4f4ffe3 (SureFire's M-MLOK-S page, M-MLOK-S-BK_isoL: the M-LOK mount alone from above, 1500 x 1500)","scaleRef":"the two screws' centres in the same photo, 759 px apart (.mlok_screw_spacing)","method":"the right counterbore along the screws' line, 370 px: 0.49 of the spacing; by hand","via":"harvest"}}],"note":"Coarse, read with .mlok_base_width."},"mount_screw_head_diameter":{"label":"Picatinny mount: diameter of the mount screw's head, at the moving jaw's end","kind":"length","measurements":[{"id":"surefire-left","value":0.19,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/surefire-scout-light-pro-dual-fuel 240f795d3e2a (SureFire's gallery, M640DF-BK-PRO-profileL: the light on its Picatinny mount, left side, on white, 1500 x 1500)","scaleRef":"the `clamp` trace's frame for this photo: four of the body's steps, 260.7 px/in (rms 0.003 in)","method":"the head's dark run just under the jaw (row 1032): columns 1016 to 1065, 49 px; by hand on the pixel values. It is centred on the plate (columns 968 to 1113 there)","via":"harvest"}}],"note":"The slotted screw that draws the jaw up; its head shows under the jaw in both profiles."},"mount_screw_head_proud":{"label":"Picatinny mount: how far the mount screw's head stands out of the moving jaw","kind":"length","measurements":[{"id":"surefire-left","value":0.04,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/surefire-scout-light-pro-dual-fuel 240f795d3e2a (SureFire's gallery, M640DF-BK-PRO-profileL: the light on its Picatinny mount, left side, on white, 1500 x 1500)","scaleRef":"the `clamp` trace's frame for this photo, 260.7 px/in","method":"rows 1031 (the jaw's underside) to 1041 (the head's end): 10 px; by hand","via":"harvest"}}]},"hook_back_beyond_pivot":{"label":"Picatinny mount: how far the fixed hook's block reaches past the pivot's axis, away from the rail's centre","kind":"length","measurements":[{"id":"surefire-tan","value":0.07,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/surefire-scout-light-pro-dual-fuel 0e24c7f67668 (SureFire's M-1913-S page, M-1913-S-TN_isoL: the Picatinny mount alone in tan, three-quarter view, 1500 x 1500)","scaleRef":"the pivot barrel's end face in the same photo, 415 px tall (0.360 in)","method":"the hook's block begins at row 190, 82 px above the barrel's centre (272), in the barrel's end plane: 0.198 of its diameter; by hand","via":"harvest"}}],"note":"The fixed hook hangs under the barrel: from this far past the pivot's axis on the body's side to its lip under the rail's corner."}}},{"subject":"surefire-socom-3-prong","title":"SureFire SOCOM 3-Prong Flash Hider, SF3P-556-1/2-28","dimensions":{"overall_length":{"label":"Overall length (rear face to the tines' front)","kind":"length","measurements":[{"id":"surefire","value":2.6,"unit":"in","pm":0.05,"stated":"LENGTH 2.6 in (6.6 cm)","source":{"type":"spec","publisher":"manufacturer","name":"SureFire, SOCOM 3-Prong Flash Hider (the product's page; its Key Attributes)","url":"https://www.surefire.com/socom-3-prong-flash-hider/","retrieved":"2026-10-06","via":"harvest"},"note":"One figure for the page, which sells two models (5.56 mm 1/2-28 and 7.62 mm 5/8-24)."},{"id":"trex","value":2.67,"unit":"in","stated":"Length 2.67\" (the table's column \"SureFire 3-Prong\")","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, SureFire SOCOM Flash Hider (one page for the 3-Prong, the Closed Tine and the 4-Prong)","url":"https://www.trex-arms.com/store/surefire-socom-flash-hider-1357594","retrieved":"2026-10-06","via":"harvest"}},{"id":"midway","value":2.67,"unit":"in","stated":"\"Length\", \"2.67 Inches\" (the attributes of the page's AR-15 item; its AR-10 item has 2.84)","source":{"type":"spec","publisher":"retailer","name":"MidwayUSA, Surefire SOCOM Flash Hider Suppressor Adapter","url":"https://www.midwayusa.com/product/1016579424","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"surefire","reason":"The maker's own page. Two sellers agree on 2.67, 2.7% more; neither says where its figure is from. The model is scaled by this one, and the patent's drawn thread is nearer 1/2 in by it."},"note":"The maker's page says 2.6 in; two sellers say 2.67. Kept apart: 2.67 is outside what 2.6 allows. By the patent's rear view the 1/2 in thread is drawn 0.506 across at 2.6 and 0.520 at 2.67; its flats are 0.731 across at 2.6 and 0.751 at 2.67. And Primary Arms' photos of this device and of the WARCOMP, whose flange the same suppressors lock onto, have the two flanges the same size only if this one is 2.63 to 2.65 long where the WARCOMP is its published 2.7 (253 px of 701 and 243 of 678 here, 253 of 721 and 256 of 727 there): between the two figures, and inside the maker's own ±."},"shim_stack":{"label":"Shims between the barrel's shoulder and the device's rear face, as installed","kind":"length","measurements":[{"id":"range","value":0.018,"unit":"in","pm":0.018,"source":{"type":"derived","basis":"Between no shim and one pitch of the 1/2-28 thread (1/28 in), from the manual's shim chart for 28 threads per inch (71-01-997 Rev E, pages 1 and 5; the copy T.REX ARMS hosts, references/surefire-socom-3-prong/docs/e3d676201d.pdf): the midpoint, ± half the range.","via":"harvest"}}],"note":"The device is timed with shims (\"To properly time the indexing tab on the adapter to bottom dead center (BDC) position, a combination of shims may be required\"), from a kit of three thicknesses: \".001\", \".005\", \".020\", worth \"1/36 Turn\", \"1/7 Turn\", \"2/3 Turn\" on 28 threads per inch. A whole turn is one pitch, .036: the stack is whatever that barrel needs within it. The value is the middle of that and the ± all of it."},"length":{"label":"Length ahead of the barrel's shoulder, installed (to the front face; the shims' thickness included)","kind":"length","measurements":[{"id":"stack","value":2.618,"unit":"in","source":{"type":"derived","expr":"{.shim_stack} + {.overall_length}","via":"harvest"},"note":"The shims against the shoulder, the device against the shims."}]},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"surefire","value":3.9,"unit":"oz","stated":"WEIGHT 3.9 oz (110.5 g)","source":{"type":"spec","publisher":"manufacturer","name":"SureFire, SOCOM 3-Prong Flash Hider (the product's page; its Key Attributes)","url":"https://www.surefire.com/socom-3-prong-flash-hider/","retrieved":"2026-10-06","via":"harvest"}},{"id":"trex","value":3.6,"unit":"oz","stated":"Weight 3.6 oz (the table's column \"SureFire 3-Prong\")","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, SureFire SOCOM Flash Hider (one page for the 3-Prong, the Closed Tine and the 4-Prong)","url":"https://www.trex-arms.com/store/surefire-socom-flash-hider-1357594","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"surefire","reason":"The maker's own page. T.REX ARMS' table has 0.3 oz less and doesn't say whose figure it is."}},"od":{"label":"Largest outside diameter (the flange at the rear)","kind":"length","measurements":[{"id":"patent","value":0.962,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/surefire-socom-3-prong 6ea6651fb575 (US D687,119 S, SureFire, FIG. 5 top plan; the patent office's copy, page 6, 2560 x 3300)","scaleRef":"the figure's own length, rear face to the tines' front, 1711 px (columns 396 to 2107), as overall_length (2.6): 658.1 px/in","method":"the outline's extent across the axis at each column, read at the strokes' outer edges (the drawing is in broken strokes: the envelope over neighbouring columns); the ± is the published length's own ± 0.05 and two pixels","via":"harvest"},"note":"633 px, columns 506 to 580."},{"id":"photo","value":0.938,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/surefire-socom-3-prong 30af9029c34b (Primary Arms' gallery, SF3P-556-1-2-28_02: the device standing, seen square from its underside, on white, 2000 x 1333)","scaleRef":"its own length in the photo, 701 px (rows 339 to 1039), as overall_length (2.6): 269.6 px/in","method":"the silhouette's width across the flange at a level of 200 of 255, 253 px; a black round part's lit edges read thin on white (the same photo has every round section 2.3 to 2.8% under the patent's and its flats equal to it)","via":"harvest"}}],"adopt":{"from":"patent","reason":"The line drawing has no lit edge to read thin. The photo's 2.5% less is what a black tube loses on white, and its flats, which have no such edge, are the patent's to 0.3%."}},"boss_od":{"label":"Rear boss (the short journal behind the flange), diameter","kind":"length","measurements":[{"id":"patent","value":0.685,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/surefire-socom-3-prong 6ea6651fb575 (US D687,119 S, SureFire, FIG. 5 top plan; the patent office's copy, page 6, 2560 x 3300)","scaleRef":"the figure's own length, rear face to the tines' front, 1711 px (columns 396 to 2107), as overall_length (2.6): 658.1 px/in","method":"the outline's extent across the axis at each column, read at the strokes' outer edges (the drawing is in broken strokes: the envelope over neighbouring columns); the ± is the published length's own ± 0.05 and two pixels","via":"harvest"},"note":"451 px, columns 396 to 505. The rear view (FIG. 8) has it 0.687 at the flange's 0.962."}]},"boss_length":{"label":"Rear boss, length (rear face to the flange's rear face)","kind":"length","measurements":[{"id":"patent","value":0.167,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/surefire-socom-3-prong 6ea6651fb575 (US D687,119 S, SureFire, FIG. 5 top plan; the patent office's copy, page 6, 2560 x 3300)","scaleRef":"the figure's own length, rear face to the tines' front, 1711 px (columns 396 to 2107), as overall_length (2.6): 658.1 px/in","method":"the outline's extent across the axis at each column, read at the strokes' outer edges (the drawing is in broken strokes: the envelope over neighbouring columns); the ± is the published length's own ± 0.05 and two pixels","via":"harvest"},"note":"110 px. FIG. 3 has 0.160 (119 px of 1928)."}]},"flange_length":{"label":"Flange, length of its cylinder (ahead of the boss, to where its front cone begins)","kind":"length","measurements":[{"id":"patent","value":0.112,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/surefire-socom-3-prong 6ea6651fb575 (US D687,119 S, SureFire, FIG. 5 top plan; the patent office's copy, page 6, 2560 x 3300)","scaleRef":"the figure's own length, rear face to the tines' front, 1711 px (columns 396 to 2107), as overall_length (2.6): 658.1 px/in","method":"the outline's extent across the axis at each column, read at the strokes' outer edges (the drawing is in broken strokes: the envelope over neighbouring columns); the ± is the published length's own ± 0.05 and two pixels","via":"harvest"},"note":"74 px, columns 506 to 580. Drawn in broken lines, as the boss and the flats are: the patent doesn't claim them, and draws the flange's rear corner square."},{"id":"photo","value":0.137,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/surefire-socom-3-prong 30af9029c34b (Primary Arms' gallery, SF3P-556-1-2-28_02: the device standing, seen square from its underside, on white, 2000 x 1333)","scaleRef":"its own length in the photo, 701 px (rows 339 to 1039), as overall_length (2.6): 269.6 px/in","method":"the silhouette's width row by row at a level of 200 of 255: where each section begins and ends along the device (positions along it don't suffer the lit edge that thins a black round's width)","via":"harvest"},"note":"37 px: the rear face at row 994.5 (its corner is rounded over nine rows, which the patent draws square), the cone's start at 957.5. The other photo (b963338c145d) has the same: 0.0767 to 0.1195 of its length at full width."}],"adopt":{"from":"photo","reason":"Where a feature is on the product is read on the product: both of Primary Arms' photos have the flange's full width running 0.025 in further forward than the patent draws it, the cone ahead of it that much shorter."}},"cone_length":{"label":"Cone ahead of the flange (from the flange's diameter down to the collar's), length","kind":"length","measurements":[{"id":"patent","value":0.068,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/surefire-socom-3-prong 6ea6651fb575 (US D687,119 S, SureFire, FIG. 5 top plan; the patent office's copy, page 6, 2560 x 3300)","scaleRef":"the figure's own length, rear face to the tines' front, 1711 px (columns 396 to 2107), as overall_length (2.6): 658.1 px/in","method":"the outline's extent across the axis at each column, read at the strokes' outer edges (the drawing is in broken strokes: the envelope over neighbouring columns); the ± is the published length's own ± 0.05 and two pixels","via":"harvest"},"note":"45 px, columns 580 to 625: from 633 px across to 579."},{"id":"photo","value":0.056,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/surefire-socom-3-prong 30af9029c34b (Primary Arms' gallery, SF3P-556-1-2-28_02: the device standing, seen square from its underside, on white, 2000 x 1333)","scaleRef":"its own length in the photo, 701 px (rows 339 to 1039), as overall_length (2.6): 269.6 px/in","method":"the silhouette's width row by row at a level of 200 of 255: where each section begins and ends along the device (positions along it don't suffer the lit edge that thins a black round's width)","via":"harvest"},"note":"15 px, rows 943 to 957: it ends 0.360 from the rear face."}],"adopt":{"from":"photo","reason":"With the flange's length, from the same photo: the cone then ends where the product has it."},"note":"The face a suppressor's back end would draw up against or cover: see suppressor_seat_x. The side view (FIG. 3) draws it longer, 0.086 (64 px of 1928), on the side away from the tab; the plan is used."},"collar_od":{"label":"Collar (the section the flats are cut in, and the lands either side of the two grooves), diameter","kind":"length","measurements":[{"id":"patent","value":0.88,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/surefire-socom-3-prong 6ea6651fb575 (US D687,119 S, SureFire, FIG. 5 top plan; the patent office's copy, page 6, 2560 x 3300)","scaleRef":"the figure's own length, rear face to the tines' front, 1711 px (columns 396 to 2107), as overall_length (2.6): 658.1 px/in","method":"the outline's extent across the axis at each column, read at the strokes' outer edges (the drawing is in broken strokes: the envelope over neighbouring columns); the ± is the published length's own ± 0.05 and two pixels","via":"harvest"},"note":"579 to 580 px: behind the flats (columns 625 to 686), ahead of them and on both lands. FIG. 3, where the flats face the lens, has the whole section at 652 px of a 1928 px length: 0.879."}]},"flats":{"label":"Wrench flats","kind":"count","measurements":[{"id":"patent","value":2,"unit":"count","source":{"type":"photo","photo":"references/surefire-socom-3-prong 6ea6651fb575 (US D687,119 S, SureFire, FIG. 5 top plan; the patent office's copy, page 6, 2560 x 3300)","scaleRef":"the figure's own length, rear face to the tines' front, 1711 px (columns 396 to 2107), as overall_length (2.6): 658.1 px/in","method":"the outline's extent across the axis at each column, read at the strokes' outer edges (the drawing is in broken strokes: the envelope over neighbouring columns); the ± is the published length's own ± 0.05 and two pixels","via":"harvest"},"note":"One each side: the plan's outline steps in on both sides over the same stretch (FIG. 5, FIG. 6), and FIG. 3 and FIG. 4 each show one face-on as a rectangle. T.REX ARMS' table: \"Wrench Flats Yes\"."}]},"flats_across":{"label":"Wrench flats, across","kind":"length","measurements":[{"id":"patent","value":0.731,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/surefire-socom-3-prong 6ea6651fb575 (US D687,119 S, SureFire, FIG. 5 top plan; the patent office's copy, page 6, 2560 x 3300)","scaleRef":"the figure's own length, rear face to the tines' front, 1711 px (columns 396 to 2107), as overall_length (2.6): 658.1 px/in","method":"the outline's extent across the axis at each column, read at the strokes' outer edges (the drawing is in broken strokes: the envelope over neighbouring columns); the ± is the published length's own ± 0.05 and two pixels","via":"harvest"},"note":"481 px, columns 687 to 866. Primary Arms' photo from below (30af9029c34b) has 0.2803 of the length, 0.729."}],"note":"The manual: \"Use a torque wrench and open-ended crow's foot, M16 wrench or 3-pronged adapter wrench\" (71-01-997 Rev E, step 6). The Army compensator's flats, which that wrench is for, are .75 -.02."},"flats_x":{"label":"Wrench flats, rear end (from the rear face)","kind":"length","measurements":[{"id":"patent","value":0.442,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/surefire-socom-3-prong 6ea6651fb575 (US D687,119 S, SureFire, FIG. 5 top plan; the patent office's copy, page 6, 2560 x 3300)","scaleRef":"the figure's own length, rear face to the tines' front, 1711 px (columns 396 to 2107), as overall_length (2.6): 658.1 px/in","method":"the outline's extent across the axis at each column, read at the strokes' outer edges (the drawing is in broken strokes: the envelope over neighbouring columns); the ± is the published length's own ± 0.05 and two pixels","via":"harvest"},"note":"Column 687, 291 px from the rear face. Primary Arms' photo from below has the flats from 0.464 to 0.719: their front end where the patent has it, their rear end 0.02 further forward."}]},"flats_length":{"label":"Wrench flats, length along the device","kind":"length","measurements":[{"id":"patent","value":0.274,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/surefire-socom-3-prong 6ea6651fb575 (US D687,119 S, SureFire, FIG. 5 top plan; the patent office's copy, page 6, 2560 x 3300)","scaleRef":"the figure's own length, rear face to the tines' front, 1711 px (columns 396 to 2107), as overall_length (2.6): 658.1 px/in","method":"the outline's extent across the axis at each column, read at the strokes' outer edges (the drawing is in broken strokes: the envelope over neighbouring columns); the ± is the published length's own ± 0.05 and two pixels","via":"harvest"},"note":"180 px, to column 866."}]},"seal_grooves":{"label":"Grooves of the labyrinth seal","kind":"count","measurements":[{"id":"patent","value":2,"unit":"count","source":{"type":"photo","photo":"references/surefire-socom-3-prong 6ea6651fb575 (US D687,119 S, SureFire, FIG. 5 top plan; the patent office's copy, page 6, 2560 x 3300)","scaleRef":"the figure's own length, rear face to the tines' front, 1711 px (columns 396 to 2107), as overall_length (2.6): 658.1 px/in","method":"the outline's extent across the axis at each column, read at the strokes' outer edges (the drawing is in broken strokes: the envelope over neighbouring columns); the ± is the published length's own ± 0.05 and two pixels","via":"harvest"},"note":"Two grooves, three lands counting the collar's ring behind them: FIG. 3 to FIG. 6 all, and both of Primary Arms' side photos."}],"note":"SureFire: \"Labyrinth seals mitigate gas leak from suppressor lock ring\". Primary Arms: \"A rear labyrinth seal minimizes potential carbon buildup in the indexing system\"."},"groove_1_x":{"label":"First groove's rear wall (from the rear face)","kind":"length","measurements":[{"id":"patent","value":0.766,"unit":"in","pm":0.016,"source":{"type":"photo","photo":"references/surefire-socom-3-prong 6ea6651fb575 (US D687,119 S, SureFire, FIG. 5 top plan; the patent office's copy, page 6, 2560 x 3300)","scaleRef":"the figure's own length, rear face to the tines' front, 1711 px (columns 396 to 2107), as overall_length (2.6): 658.1 px/in","method":"the outline's extent across the axis at each column, read at the strokes' outer edges (the drawing is in broken strokes: the envelope over neighbouring columns); the ± is the published length's own ± 0.05 and two pixels","via":"harvest"},"note":"Column 900, 504 px from the rear face."}]},"groove_width":{"label":"Grooves, width","kind":"length","measurements":[{"id":"patent","value":0.046,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/surefire-socom-3-prong 6ea6651fb575 (US D687,119 S, SureFire, FIG. 5 top plan; the patent office's copy, page 6, 2560 x 3300)","scaleRef":"the figure's own length, rear face to the tines' front, 1711 px (columns 396 to 2107), as overall_length (2.6): 658.1 px/in","method":"the outline's extent across the axis at each column, read at the strokes' outer edges (the drawing is in broken strokes: the envelope over neighbouring columns); the ± is the published length's own ± 0.05 and two pixels","via":"harvest"},"note":"31 and 30 px."}]},"groove_pitch":{"label":"Grooves, from one's rear wall to the next's","kind":"length","measurements":[{"id":"patent","value":0.084,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/surefire-socom-3-prong 6ea6651fb575 (US D687,119 S, SureFire, FIG. 5 top plan; the patent office's copy, page 6, 2560 x 3300)","scaleRef":"the figure's own length, rear face to the tines' front, 1711 px (columns 396 to 2107), as overall_length (2.6): 658.1 px/in","method":"the outline's extent across the axis at each column, read at the strokes' outer edges (the drawing is in broken strokes: the envelope over neighbouring columns); the ± is the published length's own ± 0.05 and two pixels","via":"harvest"},"note":"55 px (columns 900 and 955)."}]},"groove_d":{"label":"Grooves, diameter at their bottoms","kind":"length","measurements":[{"id":"patent","value":0.833,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/surefire-socom-3-prong 6ea6651fb575 (US D687,119 S, SureFire, FIG. 5 top plan; the patent office's copy, page 6, 2560 x 3300)","scaleRef":"the figure's own length, rear face to the tines' front, 1711 px (columns 396 to 2107), as overall_length (2.6): 658.1 px/in","method":"the outline's extent across the axis at each column, read at the strokes' outer edges (the drawing is in broken strokes: the envelope over neighbouring columns); the ± is the published length's own ± 0.05 and two pixels","via":"harvest"},"note":"548 px."}]},"seal_front_x":{"label":"Front of the last land, where the body begins (from the rear face)","kind":"length","measurements":[{"id":"patent","value":0.96,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/surefire-socom-3-prong 6ea6651fb575 (US D687,119 S, SureFire, FIG. 5 top plan; the patent office's copy, page 6, 2560 x 3300)","scaleRef":"the figure's own length, rear face to the tines' front, 1711 px (columns 396 to 2107), as overall_length (2.6): 658.1 px/in","method":"the outline's extent across the axis at each column, read at the strokes' outer edges (the drawing is in broken strokes: the envelope over neighbouring columns); the ± is the published length's own ± 0.05 and two pixels","via":"harvest"},"note":"Column 1028, 632 px from the rear face; the land's edge is chamfered over the last 9 px down to the body."}]},"body_od":{"label":"Body ahead of the seal, diameter (the cylinder the tines begin in)","kind":"length","measurements":[{"id":"patent","value":0.862,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/surefire-socom-3-prong 6ea6651fb575 (US D687,119 S, SureFire, FIG. 5 top plan; the patent office's copy, page 6, 2560 x 3300)","scaleRef":"the figure's own length, rear face to the tines' front, 1711 px (columns 396 to 2107), as overall_length (2.6): 658.1 px/in","method":"the outline's extent across the axis at each column, read at the strokes' outer edges (the drawing is in broken strokes: the envelope over neighbouring columns); the ± is the published length's own ± 0.05 and two pixels","via":"harvest"},"note":"567 px at column 1028, 565 at 1430: a cylinder within a pixel each side."}]},"taper_x":{"label":"Where the body begins to narrow (from the rear face)","kind":"length","measurements":[{"id":"patent","value":1.571,"unit":"in","pm":0.035,"source":{"type":"photo","photo":"references/surefire-socom-3-prong 6ea6651fb575 (US D687,119 S, SureFire, FIG. 5 top plan; the patent office's copy, page 6, 2560 x 3300)","scaleRef":"the figure's own length, rear face to the tines' front, 1711 px (columns 396 to 2107), as overall_length (2.6): 658.1 px/in","method":"the outline's extent across the axis at each column, read at the strokes' outer edges (the drawing is in broken strokes: the envelope over neighbouring columns); the ± is the published length's own ± 0.05 and two pixels","via":"harvest"},"note":"Column 1430, 1034 px from the rear face (0.604 of the length). Primary Arms' photo from below has its body one width to 0.595 of its length."}]},"step_x":{"label":"Step down ahead of the taper (from the rear face)","kind":"length","measurements":[{"id":"patent","value":1.992,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/surefire-socom-3-prong 6ea6651fb575 (US D687,119 S, SureFire, FIG. 5 top plan; the patent office's copy, page 6, 2560 x 3300)","scaleRef":"the figure's own length, rear face to the tines' front, 1711 px (columns 396 to 2107), as overall_length (2.6): 658.1 px/in","method":"the outline's extent across the axis at each column, read at the strokes' outer edges (the drawing is in broken strokes: the envelope over neighbouring columns); the ± is the published length's own ± 0.05 and two pixels","via":"harvest"},"note":"Columns 1707 to 1714, 1311 px from the rear face (0.766 of the length; FIG. 3 has it at 0.767, and both side photos show the line there)."}]},"step_rear_od":{"label":"Diameter just behind that step (the taper's small end)","kind":"length","measurements":[{"id":"patent","value":0.842,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/surefire-socom-3-prong 6ea6651fb575 (US D687,119 S, SureFire, FIG. 5 top plan; the patent office's copy, page 6, 2560 x 3300)","scaleRef":"the figure's own length, rear face to the tines' front, 1711 px (columns 396 to 2107), as overall_length (2.6): 658.1 px/in","method":"the outline's extent across the axis at each column, read at the strokes' outer edges (the drawing is in broken strokes: the envelope over neighbouring columns); the ± is the published length's own ± 0.05 and two pixels","via":"harvest"},"note":"554 px."}]},"step_front_od":{"label":"Diameter just ahead of that step","kind":"length","measurements":[{"id":"patent","value":0.83,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/surefire-socom-3-prong 6ea6651fb575 (US D687,119 S, SureFire, FIG. 5 top plan; the patent office's copy, page 6, 2560 x 3300)","scaleRef":"the figure's own length, rear face to the tines' front, 1711 px (columns 396 to 2107), as overall_length (2.6): 658.1 px/in","method":"the outline's extent across the axis at each column, read at the strokes' outer edges (the drawing is in broken strokes: the envelope over neighbouring columns); the ± is the published length's own ± 0.05 and two pixels","via":"harvest"},"note":"546 px."}]},"front_od":{"label":"Diameter where the tines' front corner begins to round","kind":"length","measurements":[{"id":"patent","value":0.81,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/surefire-socom-3-prong 6ea6651fb575 (US D687,119 S, SureFire, FIG. 5 top plan; the patent office's copy, page 6, 2560 x 3300)","scaleRef":"the figure's own length, rear face to the tines' front, 1711 px (columns 396 to 2107), as overall_length (2.6): 658.1 px/in","method":"the outline's extent across the axis at each column, read at the strokes' outer edges (the drawing is in broken strokes: the envelope over neighbouring columns); the ± is the published length's own ± 0.05 and two pixels","via":"harvest"},"note":"533 px at column 2035."}]},"nose_r":{"label":"Round of the tines' front outer corner, length along the device","kind":"length","measurements":[{"id":"patent","value":0.109,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/surefire-socom-3-prong 6ea6651fb575 (US D687,119 S, SureFire, FIG. 5 top plan; the patent office's copy, page 6, 2560 x 3300)","scaleRef":"the figure's own length, rear face to the tines' front, 1711 px (columns 396 to 2107), as overall_length (2.6): 658.1 px/in","method":"the outline's extent across the axis at each column, read at the strokes' outer edges (the drawing is in broken strokes: the envelope over neighbouring columns); the ± is the published length's own ± 0.05 and two pixels","via":"harvest"},"note":"72 px, columns 2035 to 2107 (the front). FIG. 3 has 88 px of 1928, 0.119. Primary Arms' photo from below rounds over its last 25 px, 0.093."}]},"tines":{"label":"Tines","kind":"count","measurements":[{"id":"patent","value":3,"unit":"count","source":{"type":"photo","photo":"references/surefire-socom-3-prong 44ef0da6caf8 (US D687,119 S, SureFire, FIG. 7 front elevation; the patent office's copy, page 8, 2560 x 3300)","scaleRef":"the figure's outer circle, the flange, 713 px across, as od (0.962): 741 px/in","method":"counted round the whole turn; circles' radii along the row and the column through the centre","via":"harvest"},"note":"Three tines and three slots, 120° apart, counted on the view from the front. One slot is at the top and one tine at the bottom: the plan (FIG. 5) has a slot along its middle, the bottom view (FIG. 6) a tine, and the tab, which the manual times to the bottom, is opposite that slot. The maker's name for it and Silencer Shop's photo from the front quarter (5f7e7e119295) say three."}]},"slot_width":{"label":"Slots between the tines, width","kind":"length","measurements":[{"id":"patent","value":0.298,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/surefire-socom-3-prong 6ea6651fb575 (US D687,119 S, SureFire, FIG. 5 top plan; the patent office's copy, page 6, 2560 x 3300)","scaleRef":"the figure's own length, rear face to the tines' front, 1711 px (columns 396 to 2107), as overall_length (2.6): 658.1 px/in","method":"the outline's extent across the axis at each column, read at the strokes' outer edges (the drawing is in broken strokes: the envelope over neighbouring columns); the ± is the published length's own ± 0.05 and two pixels","via":"harvest"},"note":"The slot that faces the plan: 196 px between its walls, centred on the axis within 2 px. FIG. 3, where that slot's edge is the outline's, puts it 19 px under the body's full radius of 319.5: a slot 0.293 wide."}]},"slot_root_x":{"label":"Slots, rear end (from the rear face)","kind":"length","measurements":[{"id":"patent","value":1.015,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/surefire-socom-3-prong 6ea6651fb575 (US D687,119 S, SureFire, FIG. 5 top plan; the patent office's copy, page 6, 2560 x 3300)","scaleRef":"the figure's own length, rear face to the tines' front, 1711 px (columns 396 to 2107), as overall_length (2.6): 658.1 px/in","method":"the outline's extent across the axis at each column, read at the strokes' outer edges (the drawing is in broken strokes: the envelope over neighbouring columns); the ± is the published length's own ± 0.05 and two pixels","via":"harvest"},"note":"The rearmost point of the slot's end, 668 px from the rear face, read on a crop at nine tenths size (± 4 px). In FIG. 3 the slot's edge leaves the body's outline at 1.017."}]},"slot_root_r":{"label":"Slots, round of the corners at their rear end","kind":"length","measurements":[{"id":"patent","value":0.075,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/surefire-socom-3-prong 6ea6651fb575 (US D687,119 S, SureFire, FIG. 5 top plan; the patent office's copy, page 6, 2560 x 3300)","scaleRef":"the figure's own length, rear face to the tines' front, 1711 px (columns 396 to 2107), as overall_length (2.6): 658.1 px/in","method":"the outline's extent across the axis at each column, read at the strokes' outer edges (the drawing is in broken strokes: the envelope over neighbouring columns); the ± is the published length's own ± 0.05 and two pixels","via":"harvest"},"note":"The walls are straight from 717 px on: the end is square with rounded corners, not a half round (which would be 0.149)."}]},"bore_d":{"label":"Hole through the device ahead of the thread","kind":"length","measurements":[{"id":"patent","value":0.244,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/surefire-socom-3-prong cd86d6e68268 (US D687,119 S, SureFire, FIG. 8 rear elevation; the patent office's copy, page 9, 2560 x 3300)","scaleRef":"the figure's outer circle, the flange, 711 px across, as od (0.962): 739 px/in","method":"circles' radii along the row and the column through the centre","via":"harvest"},"note":"The innermost circle, 90 px in radius in the rear view and in the front view both."}]},"bore_mouth_d":{"label":"That hole's mouth at the tines' roots, as the front view draws it","kind":"length","measurements":[{"id":"patent","value":0.308,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/surefire-socom-3-prong 44ef0da6caf8 (US D687,119 S, SureFire, FIG. 7 front elevation; the patent office's copy, page 8, 2560 x 3300)","scaleRef":"the figure's outer circle, the flange, 713 px across, as od (0.962): 741 px/in","method":"counted round the whole turn; circles' radii along the row and the column through the centre","via":"harvest"},"note":"The outer of two circles round the hole in the front view (102 and 114 px in radius): read as a chamfer on its mouth."}]},"thread_major_d":{"label":"The thread it is cut for: major diameter","kind":"length","measurements":[{"id":"tdp","value":0.4957,"unit":"in","pm":0.0033,"stated":"1/2-28 UNEF-2A MAJOR DIA .4989/.4924","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213","via":"user"}}],"note":"SureFire's number for it is its thread: SF3P-556-1/2-28. The Army barrel's 1/2-28, as the catalog's barrels are drawn. The patent's rear view draws the threaded hole's outer circle 0.506 across at this scale."},"thread_minor_d":{"label":"The thread it is cut for: minor diameter","kind":"length","measurements":[{"id":"tdp","value":0.4551,"unit":"in","pm":0.002,"stated":"MINOR DIA .4551 MAX","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213","via":"user"}}]},"thread_pitch":{"label":"The thread it is cut for: pitch","kind":"length","measurements":[{"id":"tdp","value":0.03571,"unit":"in","pm":0.00005,"stated":"1/2-28 UNEF-2A","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213","via":"user"}}]},"thread_depth":{"label":"Threaded hole's depth from the rear face, as drawn","kind":"length","measurements":[{"id":"as-a2","value":0.69,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{a2-flash-hider.thread_depth}","basis":"An assumption for the drawing, not a reading: the depth of the Army compensator's threaded bore (drawing 9349051).","via":"user"}}],"note":"NOT SOURCED for this device: no page, drawing or photo on file shows how deep its thread goes. The manual's Figure 4A has the adapter on shims on the barrel's shoulder, so the hole is at least as deep as the barrel's thread is long. Drawn as deep as the Army compensator's, which the same barrels take. Nothing but the model's inside reads it: the part gives no thread_length to the fit check."},"tab_width":{"label":"Indexing tab, width across the device","kind":"length","measurements":[{"id":"patent","value":0.12,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/surefire-socom-3-prong ac1eff606369 (US D687,119 S, SureFire, FIG. 6 bottom plan; the patent office's copy, page 7, 2560 x 3300)","scaleRef":"the figure's own length, 1719 px, as overall_length (2.6): 661 px/in","method":"edges picked by eye on a crop at 2.2 times size (± 3 px there, ± 0.002 in), stations counted from the rear face","via":"harvest"},"note":"80 px between the two pockets."}],"note":"The manual's \"indexing tab\", timed to the bottom: a block on the collar at the flange's front, between two pockets. Primary Arms' photo from below (30af9029c34b) shows it so, 0.11 wide and 0.15 long."},"tab_front_x":{"label":"Indexing tab, front end (from the rear face)","kind":"length","measurements":[{"id":"patent","value":0.401,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/surefire-socom-3-prong ac1eff606369 (US D687,119 S, SureFire, FIG. 6 bottom plan; the patent office's copy, page 7, 2560 x 3300)","scaleRef":"the figure's own length, 1719 px, as overall_length (2.6): 661 px/in","method":"edges picked by eye on a crop at 2.2 times size (± 3 px there, ± 0.002 in), stations counted from the rear face","via":"harvest"},"note":"265 px from the rear face. FIG. 3 has the tab's raised end at 0.374 to 0.406."}]},"tab_lip_length":{"label":"Indexing tab, length of the part that stands as high as the flange (back from its front end)","kind":"length","measurements":[{"id":"patent","value":0.029,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/surefire-socom-3-prong ac1eff606369 (US D687,119 S, SureFire, FIG. 6 bottom plan; the patent office's copy, page 7, 2560 x 3300)","scaleRef":"the figure's own length, 1719 px, as overall_length (2.6): 661 px/in","method":"edges picked by eye on a crop at 2.2 times size (± 3 px there, ± 0.002 in), stations counted from the rear face","via":"harvest"},"note":"19 px: the narrow face at the tab's front in the bottom view. FIG. 3: 24 px of 1928 at the flange's radius, 0.032."},{"id":"photo","value":0.104,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/surefire-socom-3-prong b963338c145d (Primary Arms' gallery, SF3P-556-1-2-28_03: the device standing, a wrench flat to the lens, its underside at the right edge, on white, 2000 x 1333)","scaleRef":"its own length in the photo, 678 px (rows 348 to 1025), as overall_length (2.6): 260.8 px/in","method":"the silhouette's right edge row by row at a level of 200 of 255: it stays at the flange's own (419 to 421 px) ahead of the flange while the left edge has come in to the collar's","via":"harvest"},"note":"27 rows ahead of the flange's front, then five more over which it comes down: its front end 0.42 from the rear face, against the patent's 0.401."}],"adopt":{"from":"photo","reason":"The product's own outline: the tab is a block as high as the flange from the flange's front to its end. The patent's drawing of this unclaimed end is the only thing that says otherwise."},"note":"The patent's side view has only the tab's last 0.03 in out at the flange's diameter, its top running down from the cone behind that. The product's photo has it that high all the way from the flange."},"pocket_width":{"label":"Pockets either side of the tab, width","kind":"length","measurements":[{"id":"patent","value":0.12,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/surefire-socom-3-prong ac1eff606369 (US D687,119 S, SureFire, FIG. 6 bottom plan; the patent office's copy, page 7, 2560 x 3300)","scaleRef":"the figure's own length, 1719 px, as overall_length (2.6): 661 px/in","method":"edges picked by eye on a crop at 2.2 times size (± 3 px there, ± 0.002 in), stations counted from the rear face","via":"harvest"},"note":"80 px each."}]},"pocket_rear_x":{"label":"Pockets, rear end (from the rear face)","kind":"length","measurements":[{"id":"patent","value":0.253,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/surefire-socom-3-prong ac1eff606369 (US D687,119 S, SureFire, FIG. 6 bottom plan; the patent office's copy, page 7, 2560 x 3300)","scaleRef":"the figure's own length, 1719 px, as overall_length (2.6): 661 px/in","method":"edges picked by eye on a crop at 2.2 times size (± 3 px there, ± 0.002 in), stations counted from the rear face","via":"harvest"},"note":"167 px from the rear face: they open through the flange's cone."}]},"pocket_front_x":{"label":"Pockets, front end (from the rear face)","kind":"length","measurements":[{"id":"patent","value":0.48,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/surefire-socom-3-prong ac1eff606369 (US D687,119 S, SureFire, FIG. 6 bottom plan; the patent office's copy, page 7, 2560 x 3300)","scaleRef":"the figure's own length, 1719 px, as overall_length (2.6): 661 px/in","method":"edges picked by eye on a crop at 2.2 times size (± 3 px there, ± 0.002 in), stations counted from the rear face","via":"harvest"},"note":"317 px from the rear face: a round end, in the collar."}]},"pocket_floor_d":{"label":"Pockets, diameter across their floors (at least this deep)","kind":"length","measurements":[{"id":"patent","value":0.817,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/surefire-socom-3-prong eabc794821ad (US D687,119 S, SureFire, FIG. 3 left side elevation; the patent office's copy, page 4, 2560 x 3300)","scaleRef":"the figure's own length, 1928 px, as overall_length (2.6): 741.5 px/in","method":"the outline's extent from the axis (the middle of the collar's two edges) row by row","via":"harvest"},"note":"303 px from the axis at rows 285 to 296 of the figure, against the collar's 326."}],"note":"Read where the side view's outline dips between the cone and the tab's raised end. What the outline shows there is the tab's own top, which hides the pockets behind it: they are this deep or deeper."},"suppressor_seat_x":{"label":"Where a SOCOM suppressor's rear face stands when locked on (from the barrel's shoulder)","kind":"length","measurements":[{"id":"suppressor","value":0.02,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{surefire-socom556-rc2.seat_ahead_of_device_rear}","via":"harvest"},"note":"SureFire's manual for its SOCOM suppressors draws the lock ring's rear face a hairline ahead of the barrel's end, with none of the adapter showing behind it (that part's ledger has the reading and what brackets it: the published lengths come to 0.0 on a bare adapter)."}],"note":"Not shown by any source on file for this device alone (its photos are of the device bare; its manual is its installation): the figure is the suppressor's own sources', its manual's drawings of the two locked together. Here, no photo, drawing or sentence on file for this device shows a suppressor on it (its photos are of the device alone; the patent's FIG. 9 has it on a rifle, bare; the manual is the adapter's installation). The rear end's features, from the rear face: boss to 0.167, flange to 0.304, its front cone to 0.360, collar ring to 0.442, flats to 0.716, ring to 0.766, the two seal grooves 0.766 to 0.812 and 0.850 to 0.896, last land to 0.960; the indexing tab, as high as the flange, from the flange to 0.401. Each is shim_stack further from the shoulder."}}},{"subject":"surefire-socom-4-prong","title":"SureFire SOCOM 4-Prong Flash Hider, FH556RC-1/2-28","dimensions":{"overall_length":{"label":"Overall length (rear face to the tines' front)","kind":"length","measurements":[{"id":"surefire","value":2.6,"unit":"in","pm":0.05,"stated":"LENGTH 2.6 in (6.4 cm)","source":{"type":"spec","publisher":"manufacturer","name":"SureFire, SOCOM 4-Prong Flash Hider (the product's page; its Key Attributes)","url":"https://www.surefire.com/socom-4-prong-flash-hider/","retrieved":"2026-10-06","via":"harvest"},"note":"One figure for the page, which sells two models (5.56 mm 1/2-28 and 7.62 mm 5/8-24)."},{"id":"trex","value":2.67,"unit":"in","stated":"Length 2.67\" (the table's column \"SureFire 4-Prong\")","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, SureFire SOCOM Flash Hider (one page for the 3-Prong, the Closed Tine and the 4-Prong)","url":"https://www.trex-arms.com/store/surefire-socom-flash-hider-1357594","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"surefire","reason":"The maker's own page, in inches. The seller's 2.67 is 2.7% more and doesn't say where it is from; the model is scaled by this one."},"note":"The maker's two figures don't agree with each other: 6.4 cm is 2.52 in. A seller says 2.67."},"shim_stack":{"label":"Shims between the barrel's shoulder and the device's rear face, as installed","kind":"length","measurements":[{"id":"range","value":0.018,"unit":"in","pm":0.018,"source":{"type":"derived","basis":"Between no shim and one pitch of the 1/2-28 thread (1/28 in), from the shim chart for 28 threads per inch in SureFire's adapter manual 71-01-997 Rev E (the copy T.REX ARMS hosts, references/surefire-socom-4-prong/docs/e3d676201d.pdf): the midpoint, ± half the range.","via":"harvest"}}],"note":"SureFire's adapters are timed with shims: the manual on file (71-01-997 Rev E, which names the flash hider adapters; this model's own, 71-01-828, wasn't to be had) has a kit of \".001\", \".005\", \".020\" shims worth \"1/36 Turn\", \"1/7 Turn\", \"2/3 Turn\" on 28 threads per inch. A whole turn is one pitch, .036: the value is the middle of that and the ± all of it."},"length":{"label":"Length ahead of the barrel's shoulder, installed (to the front face; the shims' thickness included)","kind":"length","measurements":[{"id":"stack","value":2.618,"unit":"in","source":{"type":"derived","expr":"{.shim_stack} + {.overall_length}","via":"harvest"},"note":"The shims against the shoulder, the device against the shims."}]},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"surefire","value":3.9,"unit":"oz","stated":"WEIGHT 3.9 oz (110.5 g)","source":{"type":"spec","publisher":"manufacturer","name":"SureFire, SOCOM 4-Prong Flash Hider (the product's page; its Key Attributes)","url":"https://www.surefire.com/socom-4-prong-flash-hider/","retrieved":"2026-10-06","via":"harvest"}},{"id":"trex","value":4,"unit":"oz","pm":0.05,"stated":"Weight 4.0 oz (the table's column \"SureFire 4-Prong\")","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, SureFire SOCOM Flash Hider (one page for the 3-Prong, the Closed Tine and the 4-Prong)","url":"https://www.trex-arms.com/store/surefire-socom-flash-hider-1357594","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"surefire","reason":"The maker's own page; the seller's table has a tenth of an ounce more."}},"od":{"label":"Largest outside diameter (the flange at the rear)","kind":"length","measurements":[{"id":"photo","value":0.945,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/surefire-socom-4-prong c9ac820f803b (Primary Arms' gallery, FH556RC-1-2-28_02: the device standing, seen square along one of its slots, on white, 2200 x 1467)","scaleRef":"its own length in the photo, 1276 px (rows 96 to 1371), as overall_length (2.6): 490.8 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a dark round reads up to 3% thin on white: not corrected), positions from the rear end's row; the slot's walls, the flat's ends and the slot's end picked by eye on a crop (± 5 px, ± 0.01 in)","via":"harvest"},"note":"464 px, 0.0745 to 0.116 of the length from the rear."}]},"boss_od":{"label":"Rear boss (the short journal behind the flange), diameter","kind":"length","measurements":[{"id":"photo","value":0.674,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/surefire-socom-4-prong c9ac820f803b (Primary Arms' gallery, FH556RC-1-2-28_02: the device standing, seen square along one of its slots, on white, 2200 x 1467)","scaleRef":"its own length in the photo, 1276 px (rows 96 to 1371), as overall_length (2.6): 490.8 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a dark round reads up to 3% thin on white: not corrected), positions from the rear end's row; the slot's walls, the flat's ends and the slot's end picked by eye on a crop (± 5 px, ± 0.01 in)","via":"harvest"},"note":"331 px."}]},"boss_length":{"label":"Rear boss, length (rear face to the flange's rear face)","kind":"length","measurements":[{"id":"photo","value":0.168,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/surefire-socom-4-prong c9ac820f803b (Primary Arms' gallery, FH556RC-1-2-28_02: the device standing, seen square along one of its slots, on white, 2200 x 1467)","scaleRef":"its own length in the photo, 1276 px (rows 96 to 1371), as overall_length (2.6): 490.8 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a dark round reads up to 3% thin on white: not corrected), positions from the rear end's row; the slot's walls, the flat's ends and the slot's end picked by eye on a crop (± 5 px, ± 0.01 in)","via":"harvest"},"note":"The boss holds its width to 0.0635 of the length; the flange's rounded rear corner begins the next row."}]},"flange_length":{"label":"Flange, length (its rear face to where its front cone begins)","kind":"length","measurements":[{"id":"photo","value":0.135,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/surefire-socom-4-prong c9ac820f803b (Primary Arms' gallery, FH556RC-1-2-28_02: the device standing, seen square along one of its slots, on white, 2200 x 1467)","scaleRef":"its own length in the photo, 1276 px (rows 96 to 1371), as overall_length (2.6): 490.8 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a dark round reads up to 3% thin on white: not corrected), positions from the rear end's row; the slot's walls, the flat's ends and the slot's end picked by eye on a crop (± 5 px, ± 0.01 in)","via":"harvest"},"note":"To 0.1165 of the length from the rear."}]},"cone_length":{"label":"Cone ahead of the flange (from the flange's diameter down to the collar's), length","kind":"length","measurements":[{"id":"photo","value":0.06,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/surefire-socom-4-prong c9ac820f803b (Primary Arms' gallery, FH556RC-1-2-28_02: the device standing, seen square along one of its slots, on white, 2200 x 1467)","scaleRef":"its own length in the photo, 1276 px (rows 96 to 1371), as overall_length (2.6): 490.8 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a dark round reads up to 3% thin on white: not corrected), positions from the rear end's row; the slot's walls, the flat's ends and the slot's end picked by eye on a crop (± 5 px, ± 0.01 in)","via":"harvest"},"note":"To 0.1395 of the length: it ends 0.363 from the rear face."}]},"collar_od":{"label":"Collar (the section the flats are cut in, and the lands either side of the two grooves), diameter","kind":"length","measurements":[{"id":"photo","value":0.862,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/surefire-socom-4-prong c9ac820f803b (Primary Arms' gallery, FH556RC-1-2-28_02: the device standing, seen square along one of its slots, on white, 2200 x 1467)","scaleRef":"its own length in the photo, 1276 px (rows 96 to 1371), as overall_length (2.6): 490.8 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a dark round reads up to 3% thin on white: not corrected), positions from the rear end's row; the slot's walls, the flat's ends and the slot's end picked by eye on a crop (± 5 px, ± 0.01 in)","via":"harvest"},"note":"423 px, 0.1395 to 0.3025 of the length, and on the lands."}]},"flats":{"label":"Wrench flats","kind":"count","measurements":[{"id":"trex","value":2,"unit":"count","stated":"Wrench Flats Yes (the table's column \"SureFire 4-Prong\"); taken as a pair","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, SureFire SOCOM Flash Hider (one page for the 3-Prong, the Closed Tine and the 4-Prong)","url":"https://www.trex-arms.com/store/surefire-socom-flash-hider-1357594","retrieved":"2026-10-06","via":"harvest"}}],"note":"One shows, at the left edge of the straight view, turned 45° from the lens; the other is taken to be opposite it."},"flats_across":{"label":"Wrench flats, across","kind":"length","measurements":[{"id":"photo","value":0.8,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/surefire-socom-4-prong c9ac820f803b (Primary Arms' gallery, FH556RC-1-2-28_02: the device standing, seen square along one of its slots, on white, 2200 x 1467)","scaleRef":"its own length in the photo, 1276 px (rows 96 to 1371), as overall_length (2.6): 490.8 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a dark round reads up to 3% thin on white: not corrected), positions from the rear end's row; the slot's walls, the flat's ends and the slot's end picked by eye on a crop (± 5 px, ± 0.01 in)","via":"harvest"}}],"note":"From one flat seen 45° off: its inner edge is 0.4 of the collar's radius from the middle of the view, which a flat this far from the axis gives. Rough."},"flats_x":{"label":"Wrench flats, rear end (from the rear face)","kind":"length","measurements":[{"id":"photo","value":0.457,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/surefire-socom-4-prong c9ac820f803b (Primary Arms' gallery, FH556RC-1-2-28_02: the device standing, seen square along one of its slots, on white, 2200 x 1467)","scaleRef":"its own length in the photo, 1276 px (rows 96 to 1371), as overall_length (2.6): 490.8 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a dark round reads up to 3% thin on white: not corrected), positions from the rear end's row; the slot's walls, the flat's ends and the slot's end picked by eye on a crop (± 5 px, ± 0.01 in)","via":"harvest"},"note":"0.1757 of the length, by eye on the crop."}]},"flats_length":{"label":"Wrench flats, length along the device","kind":"length","measurements":[{"id":"photo","value":0.295,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/surefire-socom-4-prong c9ac820f803b (Primary Arms' gallery, FH556RC-1-2-28_02: the device standing, seen square along one of its slots, on white, 2200 x 1467)","scaleRef":"its own length in the photo, 1276 px (rows 96 to 1371), as overall_length (2.6): 490.8 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a dark round reads up to 3% thin on white: not corrected), positions from the rear end's row; the slot's walls, the flat's ends and the slot's end picked by eye on a crop (± 5 px, ± 0.01 in)","via":"harvest"},"note":"To 0.2894 of the length, by eye on the crop."}]},"seal_grooves":{"label":"Grooves of the labyrinth seal","kind":"count","measurements":[{"id":"photo","value":2,"unit":"count","source":{"type":"photo","photo":"references/surefire-socom-4-prong c9ac820f803b (Primary Arms' gallery, FH556RC-1-2-28_02: the device standing, seen square along one of its slots, on white, 2200 x 1467)","scaleRef":"its own length in the photo, 1276 px (rows 96 to 1371), as overall_length (2.6): 490.8 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a dark round reads up to 3% thin on white: not corrected), positions from the rear end's row; the slot's walls, the flat's ends and the slot's end picked by eye on a crop (± 5 px, ± 0.01 in)","via":"harvest"},"note":"Two grooves ahead of the collar, in the straight view and both three-quarter views."}]},"groove_1_x":{"label":"First groove's rear wall (from the rear face)","kind":"length","measurements":[{"id":"photo","value":0.79,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/surefire-socom-4-prong c9ac820f803b (Primary Arms' gallery, FH556RC-1-2-28_02: the device standing, seen square along one of its slots, on white, 2200 x 1467)","scaleRef":"its own length in the photo, 1276 px (rows 96 to 1371), as overall_length (2.6): 490.8 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a dark round reads up to 3% thin on white: not corrected), positions from the rear end's row; the slot's walls, the flat's ends and the slot's end picked by eye on a crop (± 5 px, ± 0.01 in)","via":"harvest"},"note":"0.304 of the length."}]},"groove_width":{"label":"Grooves, width","kind":"length","measurements":[{"id":"photo","value":0.04,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/surefire-socom-4-prong c9ac820f803b (Primary Arms' gallery, FH556RC-1-2-28_02: the device standing, seen square along one of its slots, on white, 2200 x 1467)","scaleRef":"its own length in the photo, 1276 px (rows 96 to 1371), as overall_length (2.6): 490.8 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a dark round reads up to 3% thin on white: not corrected), positions from the rear end's row; the slot's walls, the flat's ends and the slot's end picked by eye on a crop (± 5 px, ± 0.01 in)","via":"harvest"},"note":"0.0155 of the length, with their rounded edges."}]},"groove_pitch":{"label":"Grooves, from one's rear wall to the next's","kind":"length","measurements":[{"id":"photo","value":0.08,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/surefire-socom-4-prong c9ac820f803b (Primary Arms' gallery, FH556RC-1-2-28_02: the device standing, seen square along one of its slots, on white, 2200 x 1467)","scaleRef":"its own length in the photo, 1276 px (rows 96 to 1371), as overall_length (2.6): 490.8 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a dark round reads up to 3% thin on white: not corrected), positions from the rear end's row; the slot's walls, the flat's ends and the slot's end picked by eye on a crop (± 5 px, ± 0.01 in)","via":"harvest"},"note":"0.0306 of the length."}]},"groove_d":{"label":"Grooves, diameter at their bottoms","kind":"length","measurements":[{"id":"photo","value":0.814,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/surefire-socom-4-prong c9ac820f803b (Primary Arms' gallery, FH556RC-1-2-28_02: the device standing, seen square along one of its slots, on white, 2200 x 1467)","scaleRef":"its own length in the photo, 1276 px (rows 96 to 1371), as overall_length (2.6): 490.8 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a dark round reads up to 3% thin on white: not corrected), positions from the rear end's row; the slot's walls, the flat's ends and the slot's end picked by eye on a crop (± 5 px, ± 0.01 in)","via":"harvest"},"note":"399 to 400 px."}]},"seal_front_x":{"label":"Front of the last land, where the body begins (from the rear face)","kind":"length","measurements":[{"id":"photo","value":0.962,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/surefire-socom-4-prong c9ac820f803b (Primary Arms' gallery, FH556RC-1-2-28_02: the device standing, seen square along one of its slots, on white, 2200 x 1467)","scaleRef":"its own length in the photo, 1276 px (rows 96 to 1371), as overall_length (2.6): 490.8 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a dark round reads up to 3% thin on white: not corrected), positions from the rear end's row; the slot's walls, the flat's ends and the slot's end picked by eye on a crop (± 5 px, ± 0.01 in)","via":"harvest"},"note":"0.370 of the length."}]},"body_od":{"label":"Body ahead of the seal, diameter (the cylinder the tines begin in)","kind":"length","measurements":[{"id":"photo","value":0.844,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/surefire-socom-4-prong c9ac820f803b (Primary Arms' gallery, FH556RC-1-2-28_02: the device standing, seen square along one of its slots, on white, 2200 x 1467)","scaleRef":"its own length in the photo, 1276 px (rows 96 to 1371), as overall_length (2.6): 490.8 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a dark round reads up to 3% thin on white: not corrected), positions from the rear end's row; the slot's walls, the flat's ends and the slot's end picked by eye on a crop (± 5 px, ± 0.01 in)","via":"harvest"},"note":"414 px, 0.373 to 0.5666 of the length."}]},"taper_x":{"label":"Where the body begins to narrow (from the rear face)","kind":"length","measurements":[{"id":"photo","value":1.473,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/surefire-socom-4-prong c9ac820f803b (Primary Arms' gallery, FH556RC-1-2-28_02: the device standing, seen square along one of its slots, on white, 2200 x 1467)","scaleRef":"its own length in the photo, 1276 px (rows 96 to 1371), as overall_length (2.6): 490.8 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a dark round reads up to 3% thin on white: not corrected), positions from the rear end's row; the slot's walls, the flat's ends and the slot's end picked by eye on a crop (± 5 px, ± 0.01 in)","via":"harvest"},"note":"0.5666 of the length."}]},"step_x":{"label":"Step down ahead of the taper (from the rear face)","kind":"length","measurements":[{"id":"photo","value":1.999,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/surefire-socom-4-prong c9ac820f803b (Primary Arms' gallery, FH556RC-1-2-28_02: the device standing, seen square along one of its slots, on white, 2200 x 1467)","scaleRef":"its own length in the photo, 1276 px (rows 96 to 1371), as overall_length (2.6): 490.8 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a dark round reads up to 3% thin on white: not corrected), positions from the rear end's row; the slot's walls, the flat's ends and the slot's end picked by eye on a crop (± 5 px, ± 0.01 in)","via":"harvest"},"note":"0.7688 of the length, where the photo shows the line across the tines."}]},"step_rear_od":{"label":"Diameter just behind that step (the taper's small end)","kind":"length","measurements":[{"id":"photo","value":0.825,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/surefire-socom-4-prong c9ac820f803b (Primary Arms' gallery, FH556RC-1-2-28_02: the device standing, seen square along one of its slots, on white, 2200 x 1467)","scaleRef":"its own length in the photo, 1276 px (rows 96 to 1371), as overall_length (2.6): 490.8 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a dark round reads up to 3% thin on white: not corrected), positions from the rear end's row; the slot's walls, the flat's ends and the slot's end picked by eye on a crop (± 5 px, ± 0.01 in)","via":"harvest"},"note":"405 px."}]},"step_front_od":{"label":"Diameter just ahead of that step","kind":"length","measurements":[{"id":"photo","value":0.805,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/surefire-socom-4-prong c9ac820f803b (Primary Arms' gallery, FH556RC-1-2-28_02: the device standing, seen square along one of its slots, on white, 2200 x 1467)","scaleRef":"its own length in the photo, 1276 px (rows 96 to 1371), as overall_length (2.6): 490.8 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a dark round reads up to 3% thin on white: not corrected), positions from the rear end's row; the slot's walls, the flat's ends and the slot's end picked by eye on a crop (± 5 px, ± 0.01 in)","via":"harvest"},"note":"395 px."}]},"front_od":{"label":"Diameter where the tines' front corner begins to round","kind":"length","measurements":[{"id":"photo","value":0.785,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/surefire-socom-4-prong c9ac820f803b (Primary Arms' gallery, FH556RC-1-2-28_02: the device standing, seen square along one of its slots, on white, 2200 x 1467)","scaleRef":"its own length in the photo, 1276 px (rows 96 to 1371), as overall_length (2.6): 490.8 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a dark round reads up to 3% thin on white: not corrected), positions from the rear end's row; the slot's walls, the flat's ends and the slot's end picked by eye on a crop (± 5 px, ± 0.01 in)","via":"harvest"},"note":"385.5 px at 0.953 of the length."}]},"nose_r":{"label":"Round of the tines' front outer corner, length along the device","kind":"length","measurements":[{"id":"photo","value":0.122,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/surefire-socom-4-prong c9ac820f803b (Primary Arms' gallery, FH556RC-1-2-28_02: the device standing, seen square along one of its slots, on white, 2200 x 1467)","scaleRef":"its own length in the photo, 1276 px (rows 96 to 1371), as overall_length (2.6): 490.8 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a dark round reads up to 3% thin on white: not corrected), positions from the rear end's row; the slot's walls, the flat's ends and the slot's end picked by eye on a crop (± 5 px, ± 0.01 in)","via":"harvest"},"note":"The last 0.047 of the length."}]},"tines":{"label":"Tines","kind":"count","measurements":[{"id":"photo","value":4,"unit":"count","source":{"type":"photo","photo":"references/surefire-socom-4-prong c9ac820f803b (Primary Arms' gallery, FH556RC-1-2-28_02: the device standing, seen square along one of its slots, on white, 2200 x 1467)","scaleRef":"its own length in the photo, 1276 px (rows 96 to 1371), as overall_length (2.6): 490.8 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a dark round reads up to 3% thin on white: not corrected), positions from the rear end's row; the slot's walls, the flat's ends and the slot's end picked by eye on a crop (± 5 px, ± 0.01 in)","via":"harvest"},"note":"The straight view looks through two slots in line, one facing the lens and one behind it (daylight shows in a slit down the middle), and has a third's edge at its right; with the fourth opposite that, four slots a quarter turn apart and four tines. Both three-quarter views (51578f23fa00, e009b94ff230) show four tine ends."}],"note":"The maker's name for it. No view on file is from the end."},"slot_width":{"label":"Slots between the tines, width","kind":"length","measurements":[{"id":"photo","value":0.19,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/surefire-socom-4-prong c9ac820f803b (Primary Arms' gallery, FH556RC-1-2-28_02: the device standing, seen square along one of its slots, on white, 2200 x 1467)","scaleRef":"its own length in the photo, 1276 px (rows 96 to 1371), as overall_length (2.6): 490.8 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a dark round reads up to 3% thin on white: not corrected), positions from the rear end's row; the slot's walls, the flat's ends and the slot's end picked by eye on a crop (± 5 px, ± 0.01 in)","via":"harvest"},"note":"The slot that faces the lens: its walls 83 px left and 10 px right of the body's middle."}]},"slot_offset":{"label":"Slots, how far each one's middle lies off the bore axis (all the same way round)","kind":"length","measurements":[{"id":"photo","value":0.074,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/surefire-socom-4-prong c9ac820f803b (Primary Arms' gallery, FH556RC-1-2-28_02: the device standing, seen square along one of its slots, on white, 2200 x 1467)","scaleRef":"its own length in the photo, 1276 px (rows 96 to 1371), as overall_length (2.6): 490.8 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a dark round reads up to 3% thin on white: not corrected), positions from the rear end's row; the slot's walls, the flat's ends and the slot's end picked by eye on a crop (± 5 px, ± 0.01 in)","via":"harvest"}}],"note":"The slots aren't cut toward the axis: seen from outside with the muzzle up, each lies to the left of it. Through two opposite slots only a slit as wide as their overlap shows daylight, 20 px in the photo, which this offset and width give."},"slot_root_x":{"label":"Slots, rear end (from the rear face)","kind":"length","measurements":[{"id":"photo","value":1.006,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/surefire-socom-4-prong c9ac820f803b (Primary Arms' gallery, FH556RC-1-2-28_02: the device standing, seen square along one of its slots, on white, 2200 x 1467)","scaleRef":"its own length in the photo, 1276 px (rows 96 to 1371), as overall_length (2.6): 490.8 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a dark round reads up to 3% thin on white: not corrected), positions from the rear end's row; the slot's walls, the flat's ends and the slot's end picked by eye on a crop (± 5 px, ± 0.01 in)","via":"harvest"},"note":"0.387 of the length."}]},"slot_root_r":{"label":"Slots, round of their rear end","kind":"length","measurements":[{"id":"photo","value":0.09,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/surefire-socom-4-prong c9ac820f803b (Primary Arms' gallery, FH556RC-1-2-28_02: the device standing, seen square along one of its slots, on white, 2200 x 1467)","scaleRef":"its own length in the photo, 1276 px (rows 96 to 1371), as overall_length (2.6): 490.8 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a dark round reads up to 3% thin on white: not corrected), positions from the rear end's row; the slot's walls, the flat's ends and the slot's end picked by eye on a crop (± 5 px, ± 0.01 in)","via":"harvest"},"note":"A round end nearly the slot's half width, by eye."}]},"bore_d":{"label":"Hole through the device ahead of the thread, as drawn","kind":"length","measurements":[{"id":"as-3-prong","value":0.244,"unit":"in","pm":0.008,"source":{"type":"derived","expr":"{surefire-socom-3-prong.bore_d}","basis":"An assumption for the drawing, not a reading of this part.","via":"harvest"}}],"note":"NOT SOURCED for this device: no view on file looks into either end. Drawn as the 3-prong's, the same maker's device for the same bullet."},"thread_major_d":{"label":"The thread it is cut for: major diameter","kind":"length","measurements":[{"id":"tdp","value":0.4957,"unit":"in","pm":0.0033,"stated":"1/2-28 UNEF-2A MAJOR DIA .4989/.4924","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213","via":"user"}}],"note":"SureFire's number for it is its thread: FH556RC-1/2-28. The Army barrel's 1/2-28, as the catalog's barrels are drawn."},"thread_minor_d":{"label":"The thread it is cut for: minor diameter","kind":"length","measurements":[{"id":"tdp","value":0.4551,"unit":"in","pm":0.002,"stated":"MINOR DIA .4551 MAX","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213","via":"user"}}]},"thread_pitch":{"label":"The thread it is cut for: pitch","kind":"length","measurements":[{"id":"tdp","value":0.03571,"unit":"in","pm":0.00005,"stated":"1/2-28 UNEF-2A","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213","via":"user"}}]},"thread_depth":{"label":"Threaded hole's depth from the rear face, as drawn","kind":"length","measurements":[{"id":"as-a2","value":0.69,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{a2-flash-hider.thread_depth}","basis":"An assumption for the drawing, not a reading: the depth of the Army compensator's threaded bore (drawing 9349051).","via":"user"}}],"note":"NOT SOURCED for this device. Drawn as deep as the Army compensator's, which the same barrels take."},"tab_width":{"label":"Indexing tab, width across the device, as drawn","kind":"length","measurements":[{"id":"as-3-prong","value":0.12,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{surefire-socom-3-prong.tab_width}","basis":"An assumption for the drawing, not a reading of this part.","via":"harvest"}}],"note":"NOT MEASURED on this device: the tab and a round pocket each side of it show in the rear three-quarter photo (51578f23fa00), in line with a tine, and not in the one straight view. Drawn as the 3-prong's, which the same suppressors index on."},"tab_front_x":{"label":"Indexing tab, front end (from the rear face), as drawn","kind":"length","measurements":[{"id":"as-3-prong","value":0.401,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{surefire-socom-3-prong.tab_front_x}","basis":"An assumption for the drawing, not a reading of this part.","via":"harvest"}}],"note":"NOT MEASURED on this device: see tab_width."},"pocket_width":{"label":"Pockets either side of the tab, width, as drawn","kind":"length","measurements":[{"id":"as-3-prong","value":0.12,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{surefire-socom-3-prong.pocket_width}","basis":"An assumption for the drawing, not a reading of this part.","via":"harvest"}}],"note":"NOT MEASURED on this device: see tab_width."},"pocket_rear_x":{"label":"Pockets, rear end (from the rear face), as drawn","kind":"length","measurements":[{"id":"as-3-prong","value":0.253,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{surefire-socom-3-prong.pocket_rear_x}","basis":"An assumption for the drawing, not a reading of this part.","via":"harvest"}}],"note":"NOT MEASURED on this device: see tab_width."},"pocket_front_x":{"label":"Pockets, front end (from the rear face), as drawn","kind":"length","measurements":[{"id":"as-3-prong","value":0.48,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{surefire-socom-3-prong.pocket_front_x}","basis":"An assumption for the drawing, not a reading of this part.","via":"harvest"}}],"note":"NOT MEASURED on this device: see tab_width."},"pocket_floor_d":{"label":"Pockets, diameter across their floors, as drawn","kind":"length","measurements":[{"id":"as-3-prong","value":0.817,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{surefire-socom-3-prong.pocket_floor_d}","basis":"An assumption for the drawing, not a reading of this part.","via":"harvest"}}],"note":"NOT MEASURED on this device: see tab_width."},"suppressor_seat_x":{"label":"Where a SOCOM suppressor's rear face stands when locked on (from the barrel's shoulder)","kind":"length","measurements":[{"id":"suppressor","value":0.02,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{surefire-socom556-rc2.seat_ahead_of_device_rear}","via":"harvest"},"note":"SureFire's manual for its SOCOM suppressors draws the lock ring's rear face a hairline ahead of the barrel's end, with none of the adapter showing behind it (that part's ledger has the reading and what brackets it: the published lengths come to 0.0 on a bare adapter)."}],"note":"Not shown by any source on file for this device alone (its photos are of the device bare; its manual is its installation): the figure is the suppressor's own sources', its manual's drawings of the two locked together. Here, no photo, drawing or sentence on file for this device shows a suppressor on it. The rear end's features, from the rear face: boss to 0.168, flange to 0.303, its front cone to 0.363, collar ring to 0.457, flats to 0.752, ring to 0.790, the two seal grooves 0.790 to 0.830 and 0.870 to 0.910, last land to 0.962. Each is shim_stack further from the shoulder. The 3-prong's are the same within 0.03."}}},{"subject":"surefire-socom556-rc2","title":"SureFire SOCOM556-RC2","dimensions":{"length":{"label":"Overall length, rear face to front face","kind":"length","measurements":[{"id":"surefire","value":6.4,"unit":"in","pm":0.05,"stated":"LENGTH 6.4 in (16.2 cm)","source":{"type":"spec","publisher":"manufacturer","name":"SureFire, SOCOM556-RC2 (product page, Key Attributes)","url":"https://www.surefire.com/socom556-rc2/","retrieved":"2026-10-06","via":"harvest"},"note":"The same page's features: \"6.4-inch overall length optimized for superior signature reduction\"."},{"id":"kygunco","value":6.4,"unit":"in","pm":0.05,"stated":"SPECIFICATIONS Diameter: 1.5in Length: 6.4in","source":{"type":"spec","publisher":"retailer","name":"KYGunCo, SureFire SOCOM556 RC2 5.56 NATO 6.4\" Silencer / Suppressor - Black","url":"https://www.kygunco.com/product/surefire-socom556-rc2-bk-socom-g2-5.56-suppressor-blk","retrieved":"2026-10-06","via":"harvest"},"note":"SureFire's own table repeated by a seller: not independent of it."},{"id":"capitol-armory","value":6.4,"unit":"in","pm":0.05,"stated":"SPECIFICATIONS Caliber: 5.56mm / .223 Length: 6.4 inches Diameter: 1.5 inches Weight: 17 ounces","source":{"type":"spec","publisher":"retailer","name":"Capitol Armory, SureFire Socom556-RC2","url":"https://www.capitolarmory.com/surefire-socom-556rc2-suppressor.html","retrieved":"2026-10-06","via":"harvest"},"note":"The same page's \"Technical Specs\" table says \"Length 6.2\" and its FEATURES list \"6.2\\\" long\": the page has both."},{"id":"primary-arms","value":6.2,"unit":"in","pm":0.05,"stated":"Length: 6.2”","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, SureFire SOCOM RC2 5.56 Sound Suppressor - Black (and the Dark Earth page: the same list)","url":"https://www.primaryarms.com/surefire-socom-2-qd-sound-suppressor-socom556-rc2-bk","retrieved":"2026-10-06","via":"harvest"}},{"id":"midwest-gun-works","value":6.2,"unit":"in","pm":0.05,"stated":"Specifications: Caliber: 5.56 mm (.223 caliber) Length: 6.2 inches Weight: 17.0 ounces Diameter: 1.5 inches","source":{"type":"spec","publisher":"retailer","name":"Midwest Gun Works, Surefire SOCOM RC Gen 2 5.56 Suppressor (SOCOM556-RC2-BK)","url":"https://www.midwestgunworks.com/page/mgwi/prod/SOCOM556-RC2-BK","retrieved":"2026-10-06","via":"harvest"}},{"id":"gun-digest","value":6.2,"unit":"in","pm":0.05,"stated":"Weight: 17 oz. Length: 6.2 in. Diameter: 1.5 in.","source":{"type":"spec","publisher":"review","name":"Gun Digest, SureFire SOCOM 556 RC-2 (specification box)","url":"https://gundigest.com/gear-ammo/surefire-socom-556-rc-2","retrieved":"2026-10-06","via":"harvest"},"note":"A specification box; not said to be measured."},{"id":"on-target","value":6.2,"unit":"in","pm":0.05,"stated":"At only 6.2-inches in length and 1.5-inches in diameter, the SOCOM556 RC2 remains one of the most-compact 5.56mm suppressor","source":{"type":"spec","publisher":"review","name":"On Target Magazine, SureFire SOCOM RC2 5.56mm Suppressor (April 2018)","url":"https://www.ontargetmagazine.com/2018/04/surefire-socom-rc2-5-56mm-suppressor/","retrieved":"2026-10-06","via":"harvest"},"note":"Not said to be measured."}],"adopt":{"from":"surefire","reason":"The maker's own figure, on its page today, and the one the photos bear out (the side view scaled by the 1.5 in tube reads 6.4 from the lock ring's rear face to the front rim). The 6.2 of three sellers and two 2017-18 articles is kept as it is printed: none says what it spans, and it matches nothing on the photos."},"note":"SureFire says 6.4 in on its page (twice); three sellers and two magazine pieces say 6.2. Nobody says between which ends. The straight side photos settle it: scaled by the tube's 1.5 in, the lock ring's rear face to the front rim is 6.4 (the `side` reading below), and no 6.2 in stretch of it ends on anything (the body's tube alone, without the ring, is 5.5)."},"od":{"label":"Largest outside diameter (the body's tube)","kind":"length","measurements":[{"id":"surefire","value":1.5,"unit":"in","pm":0.05,"stated":"DIAMETER 1.5 in (3.8 cm)","source":{"type":"spec","publisher":"manufacturer","name":"SureFire, SOCOM556-RC2 (product page, Key Attributes)","url":"https://www.surefire.com/socom556-rc2/","retrieved":"2026-10-06","via":"harvest"}},{"id":"primary-arms","value":1.5,"unit":"in","pm":0.05,"stated":"Diameter: 1.5”","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, SureFire SOCOM RC2 5.56 Sound Suppressor - Black (and the Dark Earth page: the same list)","url":"https://www.primaryarms.com/surefire-socom-2-qd-sound-suppressor-socom556-rc2-bk","retrieved":"2026-10-06","via":"harvest"}},{"id":"midwest-gun-works","value":1.5,"unit":"in","pm":0.05,"stated":"Diameter: 1.5 inches","source":{"type":"spec","publisher":"retailer","name":"Midwest Gun Works, Surefire SOCOM RC Gen 2 5.56 Suppressor (SOCOM556-RC2-BK)","url":"https://www.midwestgunworks.com/page/mgwi/prod/SOCOM556-RC2-BK","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"surefire","reason":"The maker's figure; every seller repeats it."},"note":"Taken as the tube's: in SureFire's manual's outline drawings and in the photos the lock ring's round is the tube's size within 0.02 in, and only the latch's housing stands outside it (ring_d, latch_housing_r)."},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"surefire","value":17,"unit":"oz","pm":0.05,"stated":"WEIGHT 17.0 oz (482 g)","source":{"type":"spec","publisher":"manufacturer","name":"SureFire, SOCOM556-RC2 (product page, Key Attributes)","url":"https://www.surefire.com/socom556-rc2/","retrieved":"2026-10-06","via":"harvest"}},{"id":"rainier","value":16.7,"unit":"oz","pm":0.05,"stated":"Weight: 1 lb 0.7 oz","source":{"type":"spec","publisher":"retailer","name":"Rainier Arms, SureFire SOCOM556 RC2 Sound Suppressor - Dark Earth","url":"https://www.rainierarms.com/surefire-socom556-rc2-sound-suppressor-dark-earth/","retrieved":"2026-10-06","via":"harvest"},"note":"A seller's own line under SureFire's text; whether weighed isn't said."},{"id":"capitol-armory","value":17,"unit":"oz","pm":0.5,"stated":"Weight 1lb 1oz","source":{"type":"spec","publisher":"retailer","name":"Capitol Armory, SureFire Socom556-RC2","url":"https://www.capitolarmory.com/surefire-socom-556rc2-suppressor.html","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"surefire","reason":"The maker's figure, to a tenth of an ounce; one seller prints 0.3 oz less and doesn't say it weighed one."},"note":"The suppressor alone (the muzzle device it locks onto is a part of its own: SureFire's 3-prong is 3.9 oz)."},"added_length":{"label":"What it adds to the weapon's length on the muzzle device it is measured with","kind":"length","measurements":[{"id":"surefire","value":3.8,"unit":"in","pm":0.05,"stated":"LENGTH ADDED TO WEAPON* 3.8 in (9.7 cm) *Actual length may vary, depending on which SureFire adapter is used","source":{"type":"spec","publisher":"manufacturer","name":"SureFire, SOCOM556-RC2 (product page, Key Attributes)","url":"https://www.surefire.com/socom556-rc2/","retrieved":"2026-10-06","via":"harvest"}}],"note":"SureFire names no adapter for the figure (\"*Actual length may vary, depending on which SureFire adapter is used\") and doesn't say from where it is taken. It is its own length less an adapter's: 6.4 - 2.6 (the SOCOM 3-prong's and 4-prong's \"LENGTH 2.6 in\" on SureFire's pages) = 3.8, which is the suppressor's rear face standing at the adapter's rear face, on the barrel's shoulder: what the manual's Figures 6 and 7A draw (seat_ahead_of_device_rear). On the WARCOMP (\"LENGTH 2.7 inches (6.8 cm)\", https://www.surefire.com/warcomp-flash-hider/) it would add 3.7; the 4-prong is 2.6 as the 3-prong is (https://www.surefire.com/socom-4-prong-flash-hider/). A check on the seat, not a dimension the model is drawn from."},"half_length":{"label":"Half the overall length (where the traced outline's middle sits from the rear face)","kind":"length","measurements":[{"id":"half","value":3.2,"unit":"in","pm":0.025,"source":{"type":"derived","expr":"{.length} / 2","via":"harvest"}}]},"seat_ahead_of_device_rear":{"label":"Locked on: its rear face ahead of the barrel's shoulder (where the muzzle device's frame has its origin)","kind":"length","measurements":[{"id":"manual-figure","value":0.02,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/surefire-socom556-rc2/docs/b02192f320.pdf (SureFire user manual 71-01-863 Rev G as Silencer Central hosts it), printed page 4, Figures 7A and 7B, rendered at 800 dpi","scaleRef":"Figure 7A's own scales: 235.6 px/in by the suppressor's length as `length`, 204 px/in by the barrel's stub against Figure 7B's adapter at its published 2.6 in","method":"Figure 7A: the barrel's end (its chamfer's end, column 4209.5) to the lock ring's rear face (column 4214 to 4216.5): 4.5 to 7 px, 0.02 to 0.03 in at either scale. Figure 7B gives what the barrel's end is: the adapter's rear boss begins there (columns 3898, then the flange at 3929.5)","via":"harvest"},"note":"A drawing's hairline between the ring and the barrel's end, not a dimension SureFire states."},{"id":"surefire-figures","value":0,"unit":"in","pm":0.09,"source":{"type":"derived","expr":"{.added_length} - {.length} + 2.6in","basis":"SureFire's three published figures: this suppressor's LENGTH 6.4 in and LENGTH ADDED TO WEAPON 3.8 in (https://www.surefire.com/socom556-rc2/), and the SOCOM 3-Prong Flash Hider's LENGTH 2.6 in (https://www.surefire.com/socom-3-prong-flash-hider/, read on the harvested copy 2026-10-06); each to a tenth of an inch","via":"harvest"},"note":"The 2.6 in is the adapter's, another part's figure: written here as a length until that part's ledger is in the catalog (the orchestrator's to join)."}],"adopt":{"from":"manual-figure","reason":"What SureFire draws: the ring's rear face a hairline ahead of the barrel's end. Its published figures come to 0.0 on a bare 2.6 in adapter and to 0.02 with the adapter's shims under it, and the photo of one on a rifle allows up to 0.08: all inside one another's ±."},"note":"Where it stands is the device's anchor (`suppressor_seat`); this is what the suppressor's own sources say that anchor is. The lock ring swallows the adapter whole: in the manual's Figures 6 and 7A (locked on) the barrel's plain tube runs straight into the lock ring's rear face, and none of the adapter that Figures 4 and 7B draw ahead of the barrel's chamfered end shows (its rear boss, its flange, its wrench flats). The same in On Target's photo of one locked on a rifle (0c69f586fa8c): under the ring there is a plain cylinder 0.70 in across (89 px of a ring 192 px across), the barrel or the adapter's 0.685 in rear boss, with a bright band 0.08 in tall at its top against the ring, and no flange. So the rear face stands between the shoulder and 0.08 in ahead of it. SureFire's figures bracket the same place: 6.4 long and adds 3.8, on an adapter 2.6 long, is 0.0; with the shims SureFire fits under its adapters (the 3-prong's own ledger has a stack of 0.018 in) it is 0.02. One caution on the figures of the manual: they are not one scale throughout (in Figure 7B the suppressor is drawn at 216.6 px/in by its own length and the adapter at 189 px/in by its 2.6 in), so only what lies at one place along a figure is read on it, as here."},"ring_length":{"label":"Lock ring: its length, rear face to its front edge","kind":"length","measurements":[{"id":"side","value":0.8,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/surefire-socom556-rc2 2ef29d436724 (Primary Arms SOCOM556-RC2-DE_01: the Dark Earth suppressor from its right side on white, 2000 x 1334)","scaleRef":"the tube's own width column by column as od (1.5 in): 352.7 px, 235.1 px/in (tools/trace.py, calibrate: tube); the end faces behind their rims' arcs come 6.39 in apart at that scale, and lengths are counted from the rear face so found (the silhouette trimmed to `length` about its middle)","method":"the traced side outline's stations (profiles.side)","via":"harvest"},"note":"Where the ring's front chamfer ends (the outline's 0.885 less the 0.0875 trimmed at the rear). The ± is the rear face's place behind its rim."},{"id":"manual-figure","value":0.84,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/surefire-socom556-rc2/docs/b02192f320.pdf (SureFire user manual 71-01-863 Rev G as Silencer Central hosts it), printed page 4, Figure 7B (the suppressor off the adapter, its latch toward the viewer), rendered at 800 dpi","scaleRef":"the suppressor's own length as `length`: 1386.5 px, 216.6 px/in (its tube's 327 px as od gives 218.0: the figure is in proportion within 0.6%)","method":"strokes crossed by scan lines along and across the figure (references/surefire-socom556-rc2/scratch/strokes.py, vstrokes.py)","via":"harvest"},"note":"Rear face at column 4644, the ring's front at 4825.5."}],"adopt":{"from":"side","reason":"The photograph of the product; SureFire's outline drawing has the ring 0.04 in longer, which is the photo's ± and a line's width in the drawing together. Kept beside it."}},"ring_d":{"label":"Lock ring: the diameter of its round (between its flutes, away from the latch)","kind":"length","measurements":[{"id":"manual-figure","value":1.5,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/surefire-socom556-rc2/docs/b02192f320.pdf (SureFire user manual 71-01-863 Rev G as Silencer Central hosts it), printed page 4, Figure 7B (the suppressor off the adapter, its latch toward the viewer), rendered at 800 dpi","scaleRef":"the suppressor's own length as `length`: 1386.5 px, 216.6 px/in (its tube's 327 px as od gives 218.0: the figure is in proportion within 0.6%)","method":"strokes crossed by scan lines along and across the figure (references/surefire-socom556-rc2/scratch/strokes.py, vstrokes.py)","via":"harvest"},"note":"The ring's outline 327.5 px across (rows 1962.5 to 2290) where the tube's is 327.0 (rows 1973.5 to 2300.5)."}],"note":"The same as the tube's in SureFire's drawing. In the photos the ring reads 0.02 to 0.08 in inside the tube's line on one side (5 to 12 px) and stands outside it on the other, differently in each view: the ring is unlocked there, and unlocked it sits off the body's axis (Figure 7B draws it 0.050 in off, 11 px, toward the top of that view, the latch toward the viewer; Figure 7A, locked, has its outline on the body's lines)."},"ring_rear_round":{"label":"Lock ring: the round on its rear outer edge (radius)","kind":"length","measurements":[{"id":"side","value":0.09,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/surefire-socom556-rc2 2ef29d436724 (Primary Arms SOCOM556-RC2-DE_01: the Dark Earth suppressor from its right side on white, 2000 x 1334)","scaleRef":"the tube's own width column by column as od (1.5 in): 352.7 px, 235.1 px/in (tools/trace.py, calibrate: tube); the end faces behind their rims' arcs come 6.39 in apart at that scale, and lengths are counted from the rear face so found (the silhouette trimmed to `length` about its middle)","method":"the traced side outline's stations (profiles.side)","via":"harvest"},"note":"The outline reaches the ring's full size 0.0935 in ahead of the rear face; an arc of 0.09 passes within 0.011 of its two points between."}]},"ring_front_chamfer":{"label":"Lock ring: the chamfer on its front outer edge (its length along the axis; as much across)","kind":"length","measurements":[{"id":"side","value":0.05,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/surefire-socom556-rc2 2ef29d436724 (Primary Arms SOCOM556-RC2-DE_01: the Dark Earth suppressor from its right side on white, 2000 x 1334)","scaleRef":"the tube's own width column by column as od (1.5 in): 352.7 px, 235.1 px/in (tools/trace.py, calibrate: tube); the end faces behind their rims' arcs come 6.39 in apart at that scale, and lengths are counted from the rear face so found (the silhouette trimmed to `length` about its middle)","method":"the traced side outline's stations (profiles.side)","via":"harvest"},"note":"The outline falls from the ring's full size at 0.7355 in to 0.04 in inside it at 0.7975 (0.062 along, 0.04 across): drawn as one chamfer at 45 degrees of the mean."}]},"rear_bore_d":{"label":"The opening in the lock ring's rear face (what the muzzle device goes into)","kind":"length","measurements":[{"id":"oblique","value":1.03,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/surefire-socom556-rc2 0b6cdb056ffe (Primary Arms SOCOM556-RC2-DE_02: the lock ring's end from behind and to the right, 2000 x 1333), turned 24.5 degrees so the axis is level (references/surefire-socom556-rc2/scratch/de02-rot.png)","scaleRef":"the tube's silhouette across the axis just ahead of the ring, 426 px, as od (1.5 in), less 2.3% for the ring's end standing about 0.7 in nearer the lens","method":"same-direction ratio: the opening's ellipse is 300 px across the axis (rows 255 to 555)","via":"harvest"}},{"id":"manual-figure","value":0.99,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/surefire-socom556-rc2/docs/b02192f320.pdf (SureFire user manual 71-01-863 Rev G as Silencer Central hosts it), printed page 3, Figure 5B (the suppressor's rear end seen from behind)","scaleRef":"the lock ring's outline across the same direction, as ring_d","method":"the opening's outermost circle against the ring's outline along their long axes: about 0.67 of it, by eye on a 250 dpi render","via":"harvest"}}],"adopt":{"from":"oblique","reason":"A photograph, read on a grid; SureFire's drawing agrees within 0.04 in. A second photo (the black one, a2f86f6ddb7e) reads 0.88 to 0.95 depending on where the tube's far edge, out of that picture, is taken to be."},"note":"For the device's fit: the adapter's largest diameter has to pass it. The opening's centre reads 0.07 in off the tube's axis in the photo (the ring unlocked: ring_d's note)."},"collar_d":{"label":"The toothed steel collar between the lock ring and the body, as it shows in the gap","kind":"length","measurements":[{"id":"side","value":1.26,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/surefire-socom556-rc2 2ef29d436724 (Primary Arms SOCOM556-RC2-DE_01: the Dark Earth suppressor from its right side on white, 2000 x 1334)","scaleRef":"the tube's own width column by column as od (1.5 in): 352.7 px, 235.1 px/in (tools/trace.py, calibrate: tube); the end faces behind their rims' arcs come 6.39 in apart at that scale, and lengths are counted from the rear face so found (the silhouette trimmed to `length` about its middle)","method":"the traced side outline's stations (profiles.side)","via":"harvest"},"note":"The outline's smallest radius in the gap, 0.629 at 0.826 in from the rear face: what shows between the ring's chamfer and the body's shoulder, so the collar is no larger than this."}]},"body_rear_x":{"label":"The body's rear end, from the suppressor's rear face (where its shoulder's round begins)","kind":"length","measurements":[{"id":"side","value":0.83,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/surefire-socom556-rc2 2ef29d436724 (Primary Arms SOCOM556-RC2-DE_01: the Dark Earth suppressor from its right side on white, 2000 x 1334)","scaleRef":"the tube's own width column by column as od (1.5 in): 352.7 px, 235.1 px/in (tools/trace.py, calibrate: tube); the end faces behind their rims' arcs come 6.39 in apart at that scale, and lengths are counted from the rear face so found (the silhouette trimmed to `length` about its middle)","method":"the traced side outline's stations (profiles.side)","via":"harvest"},"note":"The outline turns outward at 0.826 and reaches the tube's full size at 0.9185 (SureFire's Figure 7B has the tube's rear edge at 0.914)."}]},"body_shoulder_round":{"label":"The body's rear shoulder: its round (radius)","kind":"length","measurements":[{"id":"side","value":0.09,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/surefire-socom556-rc2 2ef29d436724 (Primary Arms SOCOM556-RC2-DE_01: the Dark Earth suppressor from its right side on white, 2000 x 1334)","scaleRef":"the tube's own width column by column as od (1.5 in): 352.7 px, 235.1 px/in (tools/trace.py, calibrate: tube); the end faces behind their rims' arcs come 6.39 in apart at that scale, and lengths are counted from the rear face so found (the silhouette trimmed to `length` about its middle)","method":"the traced side outline's stations (profiles.side)","via":"harvest"},"note":"body_rear_x to where the outline reaches the tube's size: 0.0925 in."}]},"front_corner_round":{"label":"The body's front corner: its round (radius)","kind":"length","measurements":[{"id":"side","value":0.075,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/surefire-socom556-rc2 2ef29d436724 (Primary Arms SOCOM556-RC2-DE_01: the Dark Earth suppressor from its right side on white, 2000 x 1334)","scaleRef":"the tube's own width column by column as od (1.5 in): 352.7 px, 235.1 px/in (tools/trace.py, calibrate: tube); the end faces behind their rims' arcs come 6.39 in apart at that scale, and lengths are counted from the rear face so found (the silhouette trimmed to `length` about its middle)","method":"the traced side outline's stations (profiles.side)","via":"harvest"},"note":"The outline leaves the tube's size 0.13 in behind the front face and is 0.006, 0.023 and 0.046 in inside it at 0.0645, 0.0215 and 0.0025 in from the face: an arc of 0.07 to 0.09."}]},"flutes":{"label":"Lock ring: finger flutes round it","kind":"count","measurements":[{"id":"views","value":6,"unit":"count","source":{"type":"photo","photo":"references/surefire-socom556-rc2 89bfa38440ab, 2b4e7d4cd0be, 35eefa9362ed, ceff8f4484c0 (Primary Arms SOCOM556-RC2-BK_03, -DE_03, -BK_04, -DE_04; references/surefire-socom556-rc2/scratch/rings.png puts the four rings side by side)","scaleRef":"each ring's own width in its view (an angle round the ring is the arcsine of a place across it)","method":"the flutes' and the latch's places across the ring in each view, turned into angles","via":"harvest"}}],"note":"Counted over four views that between them show the whole turn (Primary Arms' two standing views and its two pictures beside the pouch: 89bfa38440ab, 2b4e7d4cd0be, 35eefa9362ed, ceff8f4484c0): the flutes stand 45 degrees apart (three whole ones across the face of the standing black view, at -45, 0 and +45 degrees by their places across the ring; in each view with the latch in it the nearest flute is 63 to 65 degrees round from the latch). Eight places 45 degrees apart, the two either side of the latch taken by its housing: six flutes."},"flute_pitch":{"label":"Lock ring: the angle between neighbouring flutes","kind":"angle","measurements":[{"id":"views","value":45,"unit":"deg","pm":3,"source":{"type":"photo","photo":"references/surefire-socom556-rc2 89bfa38440ab (Primary Arms SOCOM556-RC2-BK_03, the black suppressor standing on its lock ring)","scaleRef":"the ring's width in the view, 224 px","method":"three flutes' middles at -75, 0 and +75 px of a radius of 112: 42 degrees apart by the arcsine, 45 with the ring's rounded edge allowed for","via":"harvest"}}]},"flute_width":{"label":"Lock ring: a flute's width","kind":"length","measurements":[{"id":"standing","value":0.41,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/surefire-socom556-rc2 89bfa38440ab (Primary Arms SOCOM556-RC2-BK_03, the black suppressor standing on its lock ring, 2000 x 1333)","scaleRef":"the ring's width in the view as ring_d, and its length as ring_length","method":"the flute that faces the lens","via":"harvest"},"note":"0.278 of the ring's width."}]},"flute_length":{"label":"Lock ring: a flute's length from the rear face to its rounded front end","kind":"length","measurements":[{"id":"standing","value":0.55,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/surefire-socom556-rc2 89bfa38440ab (Primary Arms SOCOM556-RC2-BK_03, the black suppressor standing on its lock ring, 2000 x 1333)","scaleRef":"the ring's width in the view as ring_d, and its length as ring_length","method":"the flute that faces the lens","via":"harvest"},"note":"0.67 of the ring's length, from the ring's rear rim to the flute's arch."},{"id":"manual-figure","value":0.61,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/surefire-socom556-rc2/docs/b02192f320.pdf (SureFire user manual 71-01-863 Rev G as Silencer Central hosts it), printed page 4, Figure 7A, rendered at 800 dpi","scaleRef":"the suppressor's own length in the figure as `length`: 1508 px","method":"the upper flute's front arch, 145 px ahead of the ring's rear face","via":"harvest"}}],"adopt":{"from":"manual-figure","reason":"A drawn outline with a clean rear face to count from; the photograph's rear rim is the ring's rounded edge seen from above, which shortens it."}},"flute_depth":{"label":"Lock ring: how far a flute's floor lies below the ring's round","kind":"length","measurements":[{"id":"shadow","value":0.03,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/surefire-socom556-rc2 89bfa38440ab (Primary Arms SOCOM556-RC2-BK_03, the black suppressor standing on its lock ring, 2000 x 1333)","scaleRef":"the ring's length in the view as ring_length","method":"the shadow under a flute's front arch, about a twenty-seventh of the ring's length tall, taken as the wall's height under a light from about 45 degrees above","via":"harvest"}}],"note":"The weakest figure here: no view is along a flute. A flute is a recess (every one has a shadow under its front arch and none casts one) with a wall all round it in every view, so its floor is taken to follow the ring's round: a flat floor this deep at its middle would have no wall left at its sides."},"latch_angle":{"label":"Lock ring, locked: the latch's place round the axis, from the top toward the rifle's right","kind":"angle","measurements":[{"id":"manual-figure","value":136,"unit":"deg","pm":8,"source":{"type":"photo","photo":"references/surefire-socom556-rc2/docs/b02192f320.pdf (SureFire user manual 71-01-863 Rev G as Silencer Central hosts it), printed page 4, Figure 7A (locked on), rendered at 800 dpi","scaleRef":"the lock ring's own outline in the figure","method":"the latch tab's middle 0.72 of the ring's radius below its centre line: 46 degrees below level on the side toward the viewer","via":"harvest"}}],"note":"As SureFire's Figures 6 and 7A draw the ring locked: the latch low on the side toward the viewer, which is the rifle's right (the muzzle is to the right, and the adapter's indexing tab, which the suppressor's slot seats on, is drawn at the bottom in the same views: Figure 5A). That is where SureFire has the tab put: \"To properly time the indexing tab on the adapter to bottom dead center (BDC) position, a combination of shims may be required\" (SureFire SOCOM Suppressor Adapter Installation Instructions, 71-01-997 Rev E, as T.REX ARMS hosts it: https://img.trex-arms.com/wp/uploads/2024/01/71-01-997_Suppressor-Adapter-Installation_Rev-E_print.pdf; references/surefire-socom-3-prong/docs/e3d676201d.pdf). A WARCOMP clocked for a right- or left-handed shooter turns the suppressor with it (\"the suppressor won't be indexed at the bottom-dead-center position\", the same manual)."},"latch_x0":{"label":"Latch tab: its rear end from the suppressor's rear face","kind":"length","measurements":[{"id":"manual-figure","value":0.4,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/surefire-socom556-rc2/docs/b02192f320.pdf (SureFire user manual 71-01-863 Rev G as Silencer Central hosts it), printed page 4, Figure 7B (the suppressor off the adapter, its latch toward the viewer), rendered at 800 dpi","scaleRef":"the suppressor's own length as `length`: 1386.5 px, 216.6 px/in (its tube's 327 px as od gives 218.0: the figure is in proportion within 0.6%)","method":"strokes crossed by scan lines along and across the figure (references/surefire-socom556-rc2/scratch/strokes.py, vstrokes.py)","via":"harvest"},"note":"The tab marked PUSH: columns 4730 to 4802 of a ring that begins at 4644."}]},"latch_x1":{"label":"Latch tab: its front end from the suppressor's rear face","kind":"length","measurements":[{"id":"manual-figure","value":0.73,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/surefire-socom556-rc2/docs/b02192f320.pdf (SureFire user manual 71-01-863 Rev G as Silencer Central hosts it), printed page 4, Figure 7B (the suppressor off the adapter, its latch toward the viewer), rendered at 800 dpi","scaleRef":"the suppressor's own length as `length`: 1386.5 px, 216.6 px/in (its tube's 327 px as od gives 218.0: the figure is in proportion within 0.6%)","method":"strokes crossed by scan lines along and across the figure (references/surefire-socom556-rc2/scratch/strokes.py, vstrokes.py)","via":"harvest"}}]},"latch_width":{"label":"Latch tab: its width round the ring","kind":"length","measurements":[{"id":"manual-figure","value":0.3,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/surefire-socom556-rc2/docs/b02192f320.pdf (SureFire user manual 71-01-863 Rev G as Silencer Central hosts it), printed page 4, Figure 7B (the suppressor off the adapter, its latch toward the viewer), rendered at 800 dpi","scaleRef":"the suppressor's own length as `length`: 1386.5 px, 216.6 px/in (its tube's 327 px as od gives 218.0: the figure is in proportion within 0.6%)","method":"strokes crossed by scan lines along and across the figure (references/surefire-socom556-rc2/scratch/strokes.py, vstrokes.py)","via":"harvest"},"note":"66 px tall in the figure, face on."}]},"latch_proud":{"label":"Latch tab: how far its top stands outside the tube's diameter","kind":"length","measurements":[{"id":"manual-figure","value":0.037,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/surefire-socom556-rc2/docs/b02192f320.pdf (SureFire user manual 71-01-863 Rev G as Silencer Central hosts it), printed page 4, Figure 7A (locked on), rendered at 800 dpi","scaleRef":"the lock ring's own outline in the figure","method":"the latch tab's middle 0.72 of the ring's radius below its centre line: 46 degrees below level on the side toward the viewer","via":"harvest"},"note":"The ring's outline on the latch's side reaches 9 px below the tube's lower line (rows 1696.5 and 1687.5)."}]},"bore_d":{"label":"Exit bore, as it shows in the front plate","kind":"length","measurements":[{"id":"oblique","value":0.35,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/surefire-socom556-rc2 c5a2d597da99 (Primary Arms SOCOM556-RC2-DE_00: the front plate from ahead and to the right, 2000 x 1333), turned 21.5 degrees so the axis is level (references/surefire-socom556-rc2/scratch/de00-rot.png)","scaleRef":"the tube's silhouette across the axis at the front, 460 px, as od (1.5 in): 307 px/in across the axis","method":"same-direction ratios across the axis, on a 20 px grid","via":"harvest"},"note":"The dark hole, 107 px."}]},"boss_d":{"label":"Front plate: the collar round the bore, its outside diameter","kind":"length","measurements":[{"id":"oblique","value":0.48,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/surefire-socom556-rc2 c5a2d597da99 (Primary Arms SOCOM556-RC2-DE_00: the front plate from ahead and to the right, 2000 x 1333), turned 21.5 degrees so the axis is level (references/surefire-socom556-rc2/scratch/de00-rot.png)","scaleRef":"the tube's silhouette across the axis at the front, 460 px, as od (1.5 in): 307 px/in across the axis","method":"same-direction ratios across the axis, on a 20 px grid","via":"harvest"},"note":"148 px."}]},"dish_d":{"label":"Front plate: the flat floor of its recess, its diameter","kind":"length","measurements":[{"id":"oblique","value":0.9,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/surefire-socom556-rc2 c5a2d597da99 (Primary Arms SOCOM556-RC2-DE_00: the front plate from ahead and to the right, 2000 x 1333), turned 21.5 degrees so the axis is level (references/surefire-socom556-rc2/scratch/de00-rot.png)","scaleRef":"the tube's silhouette across the axis at the front, 460 px, as od (1.5 in): 307 px/in across the axis","method":"same-direction ratios across the axis, on a 20 px grid","via":"harvest"},"note":"275 px, where the recess's wall meets its floor."}]},"crown_flats":{"label":"Front rim: the flats of its inner edge (the scallops of the crown)","kind":"count","measurements":[{"id":"surefire-picture","value":8,"unit":"count","source":{"type":"photo","photo":"references/surefire-socom556-rc2 1bcb5d46e08d (SureFire's product picture SOCOM556-RC2-BK-isoL, 1280 x 1280)","scaleRef":"none: a count","method":"the corners of the rim's inner edge, all the way round","via":"harvest"}}],"note":"Counted on SureFire's own picture, which shows the whole rim from ahead: eight corners round the rim's inner edge, four on the near half and four on the far half (references/surefire-socom556-rc2/scratch/sf-rot.png, at 140,95; 190,150; 215,260; 200,330; 150,375; 100,340; 90,230; 100,160)."},"crown_across_flats":{"label":"Front rim: its inner edge across two opposite flats, at the front face","kind":"length","measurements":[{"id":"oblique","value":1.19,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/surefire-socom556-rc2 c5a2d597da99 (Primary Arms SOCOM556-RC2-DE_00: the front plate from ahead and to the right, 2000 x 1333), turned 21.5 degrees so the axis is level (references/surefire-socom556-rc2/scratch/de00-rot.png)","scaleRef":"the tube's silhouette across the axis at the front, 460 px, as od (1.5 in): 307 px/in across the axis","method":"same-direction ratios across the axis, on a 20 px grid","via":"harvest"},"note":"365 px between the top flat and the bottom one."},{"id":"surefire-picture","value":1.24,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/surefire-socom556-rc2 1bcb5d46e08d (SureFire's product picture SOCOM556-RC2-BK-isoL, 1280 x 1280), turned 17.5 degrees so the axis is level","scaleRef":"the front end's silhouette across the axis, 312 px, as od","method":"280 px between the top corner and the bottom one: 1.346 across corners, times the cosine of 22.5 degrees","via":"harvest"}}],"adopt":{"value":1.22,"unit":"in","pm":0.04,"reason":"Between a photograph read across the flats and SureFire's picture read across the corners: neither is square to the face, and they differ by their own ±."}},"front_recess":{"label":"Front plate: how far the recess's floor lies behind the front face","kind":"length","measurements":[{"id":"oblique","value":0.16,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/surefire-socom556-rc2 c5a2d597da99 (Primary Arms SOCOM556-RC2-DE_00: the front plate from ahead and to the right, 2000 x 1333), turned 21.5 degrees so the axis is level (references/surefire-socom556-rc2/scratch/de00-rot.png)","scaleRef":"the tube's silhouette across the axis at the front, 460 px, as od (1.5 in): 307 px/in across the axis","method":"same-direction ratios across the axis, on a 20 px grid","via":"harvest"},"note":"The floor's circle and the rim's inner edge are ellipses whose centres stand 41 px apart along the axis in the picture; the collar's own ellipse (80 px along the axis for 148 across) says the face is seen from 57 degrees off its axis, so a depth shows at 0.84 of itself: 258.5 px/in."}]},"boss_height":{"label":"Front plate: how far the collar round the bore stands above the recess's floor","kind":"length","measurements":[{"id":"oblique","value":0.06,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/surefire-socom556-rc2 c5a2d597da99 (Primary Arms SOCOM556-RC2-DE_00: the front plate from ahead and to the right, 2000 x 1333), turned 21.5 degrees so the axis is level (references/surefire-socom556-rc2/scratch/de00-rot.png)","scaleRef":"the tube's silhouette across the axis at the front, 460 px, as od (1.5 in): 307 px/in across the axis","method":"same-direction ratios across the axis, on a 20 px grid","via":"harvest"},"note":"The collar's top is 26.5 px along the axis behind the rim's inner edge (0.10 in), the floor 41 px."}]},"latch_pocket_behind":{"label":"Lock ring: how far round from the latch tab's middle its pocket runs, on the side the latch's arm lies","kind":"angle","measurements":[{"id":"views","value":47,"unit":"deg","pm":8,"source":{"type":"photo","photo":"references/surefire-socom556-rc2 ceff8f4484c0 and 35eefa9362ed (Primary Arms SOCOM556-RC2-DE_04 and -BK_04, standing beside the pouch)","scaleRef":"each ring's own width in its view (an angle round the ring is the arcsine of a place across it)","method":"DE_04: the tab's middle at -23 degrees, the pocket's far wall lost in the flute at the silhouette; BK_04: the nearest flute's middle 63 degrees from the tab, its near edge 16 degrees nearer: the pocket ends at that flute's land, 47 degrees from the tab","via":"harvest"}}],"note":"The ring is cut away down to the toothed collar round the latch, between the flutes either side of it. Toward smaller angles (round from the top toward the rifle's right is positive): in the view beside the pouch the pocket runs left from the tab to the next flute."},"latch_pocket_ahead":{"label":"Lock ring: how far round from the latch tab's middle its pocket runs on the other side","kind":"angle","measurements":[{"id":"views","value":25,"unit":"deg","pm":8,"source":{"type":"photo","photo":"references/surefire-socom556-rc2 ceff8f4484c0 (Primary Arms SOCOM556-RC2-DE_04, standing beside the pouch, the latch toward the lens)","scaleRef":"the ring's own width in the view","method":"the tab's middle at -23 degrees and the pocket's wall beyond it at +2","via":"harvest"}}]},"latch_pocket_x":{"label":"Lock ring: the latch's pocket, its rear wall from the suppressor's rear face","kind":"length","measurements":[{"id":"installed","value":0.17,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/surefire-socom556-rc2 0c69f586fa8c (On Target Magazine, 1-SF-SOCOM-MainC.jpg: an RC2 locked on a rifle standing muzzle up, the latch toward the lens, 933 x 1400)","scaleRef":"the lock ring's own length in the view, 111 px, as ring_length (its width, 192 px, as ring_d gives the same scale within 4%)","method":"read on a crop enlarged 3.6 times (references/surefire-socom556-rc2/scratch/mounted.png)","via":"harvest"},"note":"The pocket's wall where it turns along the ring, 85 of the ring's 400 enlarged px above the rear face. The ring's rear rim is whole under it."}]},"latch_pocket_depth":{"label":"Lock ring: how far the latch's pocket's floor lies below the ring's round","kind":"length","measurements":[{"id":"installed","value":0.06,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/surefire-socom556-rc2 0c69f586fa8c (On Target Magazine, 1-SF-SOCOM-MainC.jpg: an RC2 locked on a rifle standing muzzle up, the latch toward the lens, 933 x 1400)","scaleRef":"the lock ring's own length in the view, 111 px, as ring_length (its width, 192 px, as ring_d gives the same scale within 4%)","method":"read on a crop enlarged 3.6 times (references/surefire-socom556-rc2/scratch/mounted.png)","via":"harvest"},"note":"A shaded band about 25 of the ring's 690 enlarged px across."}],"note":"Weak: the pocket's wall where it turns, taken as wide in the view as it is tall. The floor is the ring's own metal (lit as the ring is, no teeth on it): the toothed collar shows only ahead of the ring's front edge."},"latch_arm_width":{"label":"Latch: its arm's width along the axis (the arm runs round the ring's front edge from the tab to its pivot pin)","kind":"length","measurements":[{"id":"installed","value":0.15,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/surefire-socom556-rc2 0c69f586fa8c (On Target Magazine, 1-SF-SOCOM-MainC.jpg: an RC2 locked on a rifle standing muzzle up, the latch toward the lens, 933 x 1400)","scaleRef":"the lock ring's own length in the view, 111 px, as ring_length (its width, 192 px, as ring_d gives the same scale within 4%)","method":"read on a crop enlarged 3.6 times (references/surefire-socom556-rc2/scratch/mounted.png)","via":"harvest"},"note":"75 of the ring's 400 enlarged px, its front edge level with the tab's front end."}]}}},{"subject":"surefire-warcomp","title":"SureFire WARCOMP Flash Hider, WARCOMP-556-1/2-28","dimensions":{"overall_length":{"label":"Overall length (rear face to the tines' front)","kind":"length","measurements":[{"id":"surefire","value":2.7,"unit":"in","pm":0.05,"stated":"LENGTH 2.7 inches (6.8 cm)","source":{"type":"spec","publisher":"manufacturer","name":"SureFire, WARCOMP Flash Hider (the product's page; its Key Attributes)","url":"https://www.surefire.com/warcomp-flash-hider/","retrieved":"2026-10-06","via":"harvest"},"note":"One figure for the page, which sells two models (5.56 mm 1/2-28 and 7.62 mm 5/8-24)."},{"id":"trex","value":2.7,"unit":"in","pm":0.05,"stated":"Length 2.7\" (the table's column \"SureFire WARCOMP 3-Prong\")","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, SureFire WARCOMP Flash Hider (one page for the three-prong and the Closed Tine)","url":"https://www.trex-arms.com/store/surefire-warcomp-flash-hider/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"surefire","reason":"The maker's own page; the seller's table says the same."}},"shim_stack":{"label":"Shims between the barrel's shoulder and the device's rear face, as installed","kind":"length","measurements":[{"id":"range","value":0.018,"unit":"in","pm":0.018,"source":{"type":"derived","basis":"Between no shim and one pitch of the 1/2-28 thread (1/28 in), from the manual's shim chart for 28 threads per inch (71-01-997 Rev E, pages 1 and 5; the copy T.REX ARMS hosts, references/surefire-warcomp/docs/e3d676201d.pdf): the midpoint, ± half the range.","via":"harvest"}}],"note":"The device is timed with shims (\"To properly time the indexing tab on the adapter to bottom dead center (BDC) position, a combination of shims may be required\"), from a kit of three thicknesses: \".001\", \".005\", \".020\", worth \"1/36 Turn\", \"1/7 Turn\", \"2/3 Turn\" on 28 threads per inch. A whole turn is one pitch, .036: the stack is whatever that barrel needs within it. The value is the middle of that and the ± all of it."},"length":{"label":"Length ahead of the barrel's shoulder, installed (to the front face; the shims' thickness included)","kind":"length","measurements":[{"id":"stack","value":2.718,"unit":"in","source":{"type":"derived","expr":"{.shim_stack} + {.overall_length}","via":"harvest"},"note":"The shims against the shoulder, the device against the shims."}]},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"surefire","value":3.8,"unit":"oz","stated":"WEIGHT 3.8 ounces (107.7 g)","source":{"type":"spec","publisher":"manufacturer","name":"SureFire, WARCOMP Flash Hider (the product's page; its Key Attributes)","url":"https://www.surefire.com/warcomp-flash-hider/","retrieved":"2026-10-06","via":"harvest"}},{"id":"trex","value":3.8,"unit":"oz","stated":"Weight 3.8 oz (the table's column \"SureFire WARCOMP 3-Prong\")","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, SureFire WARCOMP Flash Hider (one page for the three-prong and the Closed Tine)","url":"https://www.trex-arms.com/store/surefire-warcomp-flash-hider/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"surefire","reason":"The maker's own page; the seller's table says the same."}},"od":{"label":"Largest outside diameter (the flange at the rear)","kind":"length","measurements":[{"id":"photo","value":0.947,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/surefire-warcomp b6910adbb177 (Primary Arms' gallery, WARCOMP-556-1-2-28_02: the device standing, seen square from its underside, on white, 2000 x 1333)","scaleRef":"its own length in the photo, 721 px (rows 297 to 1017), as overall_length (2.7): 267.0 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a black round reads up to 3% thin on white: not corrected), positions from the rear end's row","via":"harvest"},"note":"253 px, 0.0915 to 0.1318 of the length from the rear."},{"id":"side","value":0.951,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/surefire-warcomp 0b49401e457d (Primary Arms' gallery, WARCOMP-556-1-2-28_03: the device standing, seen square from its right side, the ports to the lens, its underside at the right edge, on white, 2000 x 1333)","scaleRef":"its own length in the photo, 727 px (rows 315 to 1041), as overall_length (2.7): 269.3 px/in","method":"the silhouette's width and its two edges row by row at a level of 200 of 255; hole centres and edges picked by eye on a crop at 1.8 times size (± 3 px there, ± 0.006 in)","via":"harvest"},"note":"256 px."}],"adopt":{"from":"photo","reason":"The view from below, where neither edge is the tab's. The side view agrees to 0.004."}},"boss_od":{"label":"Rear boss (the journal behind the flange), diameter","kind":"length","measurements":[{"id":"photo","value":0.678,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/surefire-warcomp b6910adbb177 (Primary Arms' gallery, WARCOMP-556-1-2-28_02: the device standing, seen square from its underside, on white, 2000 x 1333)","scaleRef":"its own length in the photo, 721 px (rows 297 to 1017), as overall_length (2.7): 267.0 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a black round reads up to 3% thin on white: not corrected), positions from the rear end's row","via":"harvest"},"note":"181 px; the side view has 182.5 of 727, 0.678."}]},"boss_length":{"label":"Rear boss, length (rear face to the flange's rear face)","kind":"length","measurements":[{"id":"photo","value":0.213,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/surefire-warcomp b6910adbb177 (Primary Arms' gallery, WARCOMP-556-1-2-28_02: the device standing, seen square from its underside, on white, 2000 x 1333)","scaleRef":"its own length in the photo, 721 px (rows 297 to 1017), as overall_length (2.7): 267.0 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a black round reads up to 3% thin on white: not corrected), positions from the rear end's row","via":"harvest"},"note":"The boss holds its width to 0.0777 of the length; the flange's rounded rear corner begins the next row, and reaches full width at 0.0915. The side view: 0.0812 and 0.0949."}],"note":"Longer than the 3-prong's (0.167) by about what this device is longer overall."},"flange_length":{"label":"Flange, length (its rear face to where its front cone begins)","kind":"length","measurements":[{"id":"photo","value":0.143,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/surefire-warcomp b6910adbb177 (Primary Arms' gallery, WARCOMP-556-1-2-28_02: the device standing, seen square from its underside, on white, 2000 x 1333)","scaleRef":"its own length in the photo, 721 px (rows 297 to 1017), as overall_length (2.7): 267.0 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a black round reads up to 3% thin on white: not corrected), positions from the rear end's row","via":"harvest"},"note":"To 0.1318 of the length from the rear (the side view: 0.1334)."}]},"cone_length":{"label":"Cone ahead of the flange (from the flange's diameter down to the collar's), length","kind":"length","measurements":[{"id":"photo","value":0.06,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/surefire-warcomp b6910adbb177 (Primary Arms' gallery, WARCOMP-556-1-2-28_02: the device standing, seen square from its underside, on white, 2000 x 1333)","scaleRef":"its own length in the photo, 721 px (rows 297 to 1017), as overall_length (2.7): 267.0 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a black round reads up to 3% thin on white: not corrected), positions from the rear end's row","via":"harvest"},"note":"0.1318 to 0.154 of the length: it ends 0.416 from the rear face."}]},"collar_od":{"label":"Ported collar (between the flange's cone and the body), diameter","kind":"length","measurements":[{"id":"photo","value":0.869,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/surefire-warcomp b6910adbb177 (Primary Arms' gallery, WARCOMP-556-1-2-28_02: the device standing, seen square from its underside, on white, 2000 x 1333)","scaleRef":"its own length in the photo, 721 px (rows 297 to 1017), as overall_length (2.7): 267.0 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a black round reads up to 3% thin on white: not corrected), positions from the rear end's row","via":"harvest"},"note":"232 px; the side view has 232 of 727, 0.862."}]},"collar_front_x":{"label":"Ported collar, front end, where it steps down to the body (from the rear face)","kind":"length","measurements":[{"id":"photo","value":1.019,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/surefire-warcomp b6910adbb177 (Primary Arms' gallery, WARCOMP-556-1-2-28_02: the device standing, seen square from its underside, on white, 2000 x 1333)","scaleRef":"its own length in the photo, 721 px (rows 297 to 1017), as overall_length (2.7): 267.0 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a black round reads up to 3% thin on white: not corrected), positions from the rear end's row","via":"harvest"},"note":"0.3773 of the length; the side view steps down between 0.3686 and 0.3796."}]},"flats":{"label":"Wrench flats","kind":"count","measurements":[{"id":"photo","value":0,"unit":"count","source":{"type":"photo","photo":"references/surefire-warcomp b6910adbb177 (Primary Arms' gallery, WARCOMP-556-1-2-28_02: the device standing, seen square from its underside, on white, 2000 x 1333)","scaleRef":"its own length in the photo, 721 px (rows 297 to 1017), as overall_length (2.7): 267.0 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a black round reads up to 3% thin on white: not corrected), positions from the rear end's row","via":"harvest"},"note":"None: the collar keeps one width from the cone to the body in both views, a quarter turn apart (a flat would step one of them in)."},{"id":"trex","value":0,"unit":"count","stated":"Wrench Flats No (the table's column \"SureFire WARCOMP 3-Prong\")","source":{"type":"spec","publisher":"retailer","name":"T.REX ARMS, SureFire WARCOMP Flash Hider (one page for the three-prong and the Closed Tine)","url":"https://www.trex-arms.com/store/surefire-warcomp-flash-hider/","retrieved":"2026-10-06","via":"harvest"}}],"adopt":{"from":"photo","reason":"Seen on the part's own photos; the seller's table says the same."},"note":"It is turned by its tines: the manual lists a \"3-Prong Wrench (as applies)\" in the box."},"body_od":{"label":"Body ahead of the collar, diameter","kind":"length","measurements":[{"id":"photo","value":0.839,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/surefire-warcomp b6910adbb177 (Primary Arms' gallery, WARCOMP-556-1-2-28_02: the device standing, seen square from its underside, on white, 2000 x 1333)","scaleRef":"its own length in the photo, 721 px (rows 297 to 1017), as overall_length (2.7): 267.0 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a black round reads up to 3% thin on white: not corrected), positions from the rear end's row","via":"harvest"},"note":"224 px, from 0.3773 to 0.7739 of the length: one width within two pixels."}]},"step_x":{"label":"Step down in the body (from the rear face)","kind":"length","measurements":[{"id":"photo","value":2.09,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/surefire-warcomp b6910adbb177 (Primary Arms' gallery, WARCOMP-556-1-2-28_02: the device standing, seen square from its underside, on white, 2000 x 1333)","scaleRef":"its own length in the photo, 721 px (rows 297 to 1017), as overall_length (2.7): 267.0 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a black round reads up to 3% thin on white: not corrected), positions from the rear end's row","via":"harvest"},"note":"0.7739 of the length; the side view shows the line there."}]},"step_front_od":{"label":"Diameter ahead of that step, to the tines' rounded front","kind":"length","measurements":[{"id":"photo","value":0.824,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/surefire-warcomp b6910adbb177 (Primary Arms' gallery, WARCOMP-556-1-2-28_02: the device standing, seen square from its underside, on white, 2000 x 1333)","scaleRef":"its own length in the photo, 721 px (rows 297 to 1017), as overall_length (2.7): 267.0 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a black round reads up to 3% thin on white: not corrected), positions from the rear end's row","via":"harvest"},"note":"220 px, to 0.9709 of the length."}]},"nose_r":{"label":"Round of the tines' front outer corner, length along the device","kind":"length","measurements":[{"id":"photo","value":0.079,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/surefire-warcomp b6910adbb177 (Primary Arms' gallery, WARCOMP-556-1-2-28_02: the device standing, seen square from its underside, on white, 2000 x 1333)","scaleRef":"its own length in the photo, 721 px (rows 297 to 1017), as overall_length (2.7): 267.0 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a black round reads up to 3% thin on white: not corrected), positions from the rear end's row","via":"harvest"},"note":"The last 0.0291 of the length."}]},"tines":{"label":"Tines","kind":"count","measurements":[{"id":"photo","value":3,"unit":"count","source":{"type":"photo","photo":"references/surefire-warcomp b6910adbb177 (Primary Arms' gallery, WARCOMP-556-1-2-28_02: the device standing, seen square from its underside, on white, 2000 x 1333)","scaleRef":"its own length in the photo, 721 px (rows 297 to 1017), as overall_length (2.7): 267.0 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a black round reads up to 3% thin on white: not corrected), positions from the rear end's row","via":"harvest"},"note":"The two views cover the turn: from below one tine faces the lens with a slot each side of it; from the right side the outline's top edge is a third slot's (the body reads 217 px there against 224 from below: a slot 0.29 wide at the top). Primary Arms' and Mile High's three-quarter views show three tine ends."}],"note":"T.REX ARMS calls it the \"WARCOMP 3-Prong\" beside the Closed Tine."},"slot_width":{"label":"Slots between the tines, width","kind":"length","measurements":[{"id":"photo","value":0.285,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/surefire-warcomp b6910adbb177 (Primary Arms' gallery, WARCOMP-556-1-2-28_02: the device standing, seen square from its underside, on white, 2000 x 1333)","scaleRef":"its own length in the photo, 721 px (rows 297 to 1017), as overall_length (2.7): 267.0 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a black round reads up to 3% thin on white: not corrected), positions from the rear end's row","via":"harvest"},"note":"The bottom tine's face between its two slots is 144 px wide (edges by eye on a crop, ± 3 px); with the slots 120° either side of the top and the body 224 px across, their walls are that far apart when each slot is 76 px wide. The side view's top edge gives 0.29."}]},"slot_root_x":{"label":"Slots, rear end (from the rear face)","kind":"length","measurements":[{"id":"photo","value":1.13,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/surefire-warcomp b6910adbb177 (Primary Arms' gallery, WARCOMP-556-1-2-28_02: the device standing, seen square from its underside, on white, 2000 x 1333)","scaleRef":"its own length in the photo, 721 px (rows 297 to 1017), as overall_length (2.7): 267.0 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a black round reads up to 3% thin on white: not corrected), positions from the rear end's row","via":"harvest"},"note":"0.420 of the length from below, 0.415 from the side: by eye on the crops."}]},"slot_root_r":{"label":"Slots, round of the corners at their rear end","kind":"length","measurements":[{"id":"photo","value":0.04,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/surefire-warcomp 0b49401e457d (Primary Arms' gallery, WARCOMP-556-1-2-28_03: the device standing, seen square from its right side, the ports to the lens, its underside at the right edge, on white, 2000 x 1333)","scaleRef":"its own length in the photo, 727 px (rows 315 to 1041), as overall_length (2.7): 269.3 px/in","method":"the silhouette's width and its two edges row by row at a level of 200 of 255; hole centres and edges picked by eye on a crop at 1.8 times size (± 3 px there, ± 0.006 in)","via":"harvest"},"note":"A square end with small rounds, by eye."}]},"port_rows":{"label":"Ports, rows round the collar","kind":"count","measurements":[{"id":"photo","value":2,"unit":"count","source":{"type":"photo","photo":"references/surefire-warcomp 0b49401e457d (Primary Arms' gallery, WARCOMP-556-1-2-28_03: the device standing, seen square from its right side, the ports to the lens, its underside at the right edge, on white, 2000 x 1333)","scaleRef":"its own length in the photo, 727 px (rows 315 to 1041), as overall_length (2.7): 269.3 px/in","method":"the silhouette's width and its two edges row by row at a level of 200 of 255; hole centres and edges picked by eye on a crop at 1.8 times size (± 3 px there, ± 0.006 in)","via":"harvest"},"note":"Two rows, the holes of one in line with the other's, in every view."}]},"port_columns":{"label":"Ports, columns (each a hole in both rows)","kind":"count","measurements":[{"id":"photo","value":6,"unit":"count","source":{"type":"photo","photo":"references/surefire-warcomp 6510c16e0122 (T.REX ARMS, Surefire-WARCOMP-4: WARCOMP-556-1/2-28 by the NSN lasered on it, standing, seen from its upper right, close, 2560 x 2560)","scaleRef":"none: a count","method":"counted across the collar, which shows all of them at once from this side: three columns, a wider land, three columns; then checked on the views that show the rest of the turn","via":"harvest"},"note":"The right side view (0b49401e457d) has the four on that side, the lowest 27° below the level; the view from below (b6910adbb177) has that one near its left edge and none anywhere else: nothing on the lower left. The unseen upper left can hold no seventh unless the pattern is lopsided about its own middle."}],"note":"Twelve holes in all, in two groups of three columns either side of a plane about 45° to the right of the top when the tab is at the bottom: SureFire's \"WARCOMP-556-1/2-28 can be timed for right- or left-handed shooters, or for neutral timing\", and the manual's drawing has the tab at the bottom as RIGHT HANDED, the ported arc from 36° left of the top to 121° right of it."},"port_d":{"label":"Ports, diameter","kind":"length","measurements":[{"id":"photo","value":0.159,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/surefire-warcomp 0b49401e457d (Primary Arms' gallery, WARCOMP-556-1-2-28_03: the device standing, seen square from its right side, the ports to the lens, its underside at the right edge, on white, 2000 x 1333)","scaleRef":"its own length in the photo, 727 px (rows 315 to 1041), as overall_length (2.7): 269.3 px/in","method":"the silhouette's width and its two edges row by row at a level of 200 of 255; hole centres and edges picked by eye on a crop at 1.8 times size (± 3 px there, ± 0.006 in)","via":"harvest"},"note":"The three holes that face the lens: 74 to 80 px across on the crop, 42.8 px."}]},"port_row_1_x":{"label":"Ports, the rear row's centres (from the rear face)","kind":"length","measurements":[{"id":"photo","value":0.596,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/surefire-warcomp 0b49401e457d (Primary Arms' gallery, WARCOMP-556-1-2-28_03: the device standing, seen square from its right side, the ports to the lens, its underside at the right edge, on white, 2000 x 1333)","scaleRef":"its own length in the photo, 727 px (rows 315 to 1041), as overall_length (2.7): 269.3 px/in","method":"the silhouette's width and its two edges row by row at a level of 200 of 255; hole centres and edges picked by eye on a crop at 1.8 times size (± 3 px there, ± 0.006 in)","via":"harvest"},"note":"Row 880.6 of the photo, 0.2206 of the length from the rear."}]},"port_row_pitch":{"label":"Ports, from the rear row's centres to the front row's","kind":"length","measurements":[{"id":"photo","value":0.206,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/surefire-warcomp 0b49401e457d (Primary Arms' gallery, WARCOMP-556-1-2-28_03: the device standing, seen square from its right side, the ports to the lens, its underside at the right edge, on white, 2000 x 1333)","scaleRef":"its own length in the photo, 727 px (rows 315 to 1041), as overall_length (2.7): 269.3 px/in","method":"the silhouette's width and its two edges row by row at a level of 200 of 255; hole centres and edges picked by eye on a crop at 1.8 times size (± 3 px there, ± 0.006 in)","via":"harvest"},"note":"55.6 px: the front row 0.802 from the rear face."}]},"port_center_angle":{"label":"Ports, the middle of their arc, from straight up toward the rifle's right (the tab at the bottom)","kind":"angle","measurements":[{"id":"photo","value":47,"unit":"deg","pm":5,"source":{"type":"photo","photo":"references/surefire-warcomp 0b49401e457d (Primary Arms' gallery, WARCOMP-556-1-2-28_03: the device standing, seen square from its right side, the ports to the lens, its underside at the right edge, on white, 2000 x 1333)","scaleRef":"its own length in the photo, 727 px (rows 315 to 1041), as overall_length (2.7): 269.3 px/in","method":"the silhouette's width and its two edges row by row at a level of 200 of 255; hole centres and edges picked by eye on a crop at 1.8 times size (± 3 px there, ± 0.006 in)","via":"harvest"},"note":"Midway between the two columns either side of the wider land, which the side view has 60° and 25° above the level (the upper one by its two edges near the outline). The manual's drawing has the NEUTRAL timing's tab 48° round from the bottom."}]},"port_group_gap":{"label":"Ports, between the two middle columns (across the wider land)","kind":"angle","measurements":[{"id":"photo","value":35,"unit":"deg","pm":5,"source":{"type":"photo","photo":"references/surefire-warcomp 0b49401e457d (Primary Arms' gallery, WARCOMP-556-1-2-28_03: the device standing, seen square from its right side, the ports to the lens, its underside at the right edge, on white, 2000 x 1333)","scaleRef":"its own length in the photo, 727 px (rows 315 to 1041), as overall_length (2.7): 269.3 px/in","method":"the silhouette's width and its two edges row by row at a level of 200 of 255; hole centres and edges picked by eye on a crop at 1.8 times size (± 3 px there, ± 0.006 in)","via":"harvest"}}]},"port_column_pitch":{"label":"Ports, between neighbouring columns within a group","kind":"angle","measurements":[{"id":"photo","value":26,"unit":"deg","pm":3,"source":{"type":"photo","photo":"references/surefire-warcomp 0b49401e457d (Primary Arms' gallery, WARCOMP-556-1-2-28_03: the device standing, seen square from its right side, the ports to the lens, its underside at the right edge, on white, 2000 x 1333)","scaleRef":"its own length in the photo, 727 px (rows 315 to 1041), as overall_length (2.7): 269.3 px/in","method":"the silhouette's width and its two edges row by row at a level of 200 of 255; hole centres and edges picked by eye on a crop at 1.8 times size (± 3 px there, ± 0.006 in)","via":"harvest"},"note":"The three that face the lens: 25° and 27° apart, by their centres' places across the collar."}]},"tab_width":{"label":"Indexing tab, width across the device","kind":"length","measurements":[{"id":"photo","value":0.136,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/surefire-warcomp b6910adbb177 (Primary Arms' gallery, WARCOMP-556-1-2-28_02: the device standing, seen square from its underside, on white, 2000 x 1333)","scaleRef":"its own length in the photo, 721 px (rows 297 to 1017), as overall_length (2.7): 267.0 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a black round reads up to 3% thin on white: not corrected), positions from the rear end's row","via":"harvest"},"note":"By eye on a crop at 1.8 times size: the two pockets' round ends are 66.7 px apart centre to centre and 30.6 px across, the tab what is left between them."}]},"tab_front_x":{"label":"Indexing tab, front end (from the rear face)","kind":"length","measurements":[{"id":"photo","value":0.468,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/surefire-warcomp 0b49401e457d (Primary Arms' gallery, WARCOMP-556-1-2-28_03: the device standing, seen square from its right side, the ports to the lens, its underside at the right edge, on white, 2000 x 1333)","scaleRef":"its own length in the photo, 727 px (rows 315 to 1041), as overall_length (2.7): 269.3 px/in","method":"the silhouette's width and its two edges row by row at a level of 200 of 255; hole centres and edges picked by eye on a crop at 1.8 times size (± 3 px there, ± 0.006 in)","via":"harvest"},"note":"0.1733 of the length."}],"note":"From the flange's front to here the tab stands as high as the flange: the side view's right edge stays at the flange's while its left has come in to the collar's."},"pocket_width":{"label":"Pockets either side of the tab, width","kind":"length","measurements":[{"id":"photo","value":0.114,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/surefire-warcomp b6910adbb177 (Primary Arms' gallery, WARCOMP-556-1-2-28_02: the device standing, seen square from its underside, on white, 2000 x 1333)","scaleRef":"its own length in the photo, 721 px (rows 297 to 1017), as overall_length (2.7): 267.0 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a black round reads up to 3% thin on white: not corrected), positions from the rear end's row","via":"harvest"},"note":"30.6 px, by eye on the crop."}]},"pocket_rear_x":{"label":"Pockets, rear end (from the rear face)","kind":"length","measurements":[{"id":"photo","value":0.282,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/surefire-warcomp b6910adbb177 (Primary Arms' gallery, WARCOMP-556-1-2-28_02: the device standing, seen square from its underside, on white, 2000 x 1333)","scaleRef":"its own length in the photo, 721 px (rows 297 to 1017), as overall_length (2.7): 267.0 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a black round reads up to 3% thin on white: not corrected), positions from the rear end's row","via":"harvest"},"note":"By eye on the crop: they open through the flange's cone into the flange."}]},"pocket_front_x":{"label":"Pockets, front end (from the rear face)","kind":"length","measurements":[{"id":"photo","value":0.543,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/surefire-warcomp b6910adbb177 (Primary Arms' gallery, WARCOMP-556-1-2-28_02: the device standing, seen square from its underside, on white, 2000 x 1333)","scaleRef":"its own length in the photo, 721 px (rows 297 to 1017), as overall_length (2.7): 267.0 px/in","method":"the silhouette's width row by row at a level of 200 of 255, each section where the width holds within two pixels; widths as read (a black round reads up to 3% thin on white: not corrected), positions from the rear end's row","via":"harvest"},"note":"By eye on the crop: a round end, in the collar."}]},"pocket_floor_d":{"label":"Pockets, diameter across their floors, as drawn","kind":"length","measurements":[{"id":"as-3-prong","value":0.817,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{surefire-socom-3-prong.pocket_floor_d}","basis":"An assumption for the drawing, not a reading of this part.","via":"harvest"}}],"note":"NOT SOURCED for this device: neither straight view shows how deep the pockets are. Drawn at the depth the 3-prong's patent shows beside its tab, the two devices' tabs being made for the same suppressors."},"bore_d":{"label":"Hole through the device ahead of the thread, as drawn","kind":"length","measurements":[{"id":"as-3-prong","value":0.244,"unit":"in","pm":0.008,"source":{"type":"derived","expr":"{surefire-socom-3-prong.bore_d}","basis":"An assumption for the drawing, not a reading of this part.","via":"harvest"}}],"note":"NOT SOURCED for this device: no view on file looks into either end. Drawn as the 3-prong's, the same maker's device for the same bullet."},"thread_major_d":{"label":"The thread it is cut for: major diameter","kind":"length","measurements":[{"id":"tdp","value":0.4957,"unit":"in","pm":0.0033,"stated":"1/2-28 UNEF-2A MAJOR DIA .4989/.4924","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213","via":"user"}}],"note":"SureFire's number for it is its thread: WARCOMP-556-1/2-28. The Army barrel's 1/2-28, as the catalog's barrels are drawn."},"thread_minor_d":{"label":"The thread it is cut for: minor diameter","kind":"length","measurements":[{"id":"tdp","value":0.4551,"unit":"in","pm":0.002,"stated":"MINOR DIA .4551 MAX","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213","via":"user"}}]},"thread_pitch":{"label":"The thread it is cut for: pitch","kind":"length","measurements":[{"id":"tdp","value":0.03571,"unit":"in","pm":0.00005,"stated":"1/2-28 UNEF-2A","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213","via":"user"}}]},"thread_depth":{"label":"Threaded hole's depth from the rear face, as drawn","kind":"length","measurements":[{"id":"as-a2","value":0.69,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{a2-flash-hider.thread_depth}","basis":"An assumption for the drawing, not a reading: the depth of the Army compensator's threaded bore (drawing 9349051).","via":"user"}}],"note":"NOT SOURCED for this device: no page, drawing or photo on file shows how deep its thread goes, nor what is inside the ported collar. The manual's Figure 4A has the adapter on shims on the barrel's shoulder, so the hole is at least as deep as the barrel's thread is long. Drawn as deep as the Army compensator's, which the same barrels take: the rear row of ports then lies over its last 0.17 in."},"suppressor_seat_x":{"label":"Where a SOCOM suppressor's rear face stands when locked on (from the barrel's shoulder)","kind":"length","measurements":[{"id":"suppressor","value":0.02,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{surefire-socom556-rc2.seat_ahead_of_device_rear}","via":"harvest"},"note":"SureFire's manual for its SOCOM suppressors draws the lock ring's rear face a hairline ahead of the barrel's end, with none of the adapter showing behind it (that part's ledger has the reading and what brackets it: the published lengths come to 0.0 on a bare adapter)."}],"note":"Not shown by any source on file for this device alone (its photos are of the device bare; its manual is its installation): the figure is the suppressor's own sources', its manual's drawings of the two locked together. Here, no photo, drawing or sentence on file for this device shows a suppressor on it. The rear end's features, from the rear face: boss to 0.213, flange to 0.356, its front cone to 0.416, the ported collar to 1.019 (the ports' rows centred 0.596 and 0.802, each hole 0.159 across); the indexing tab, as high as the flange, from the flange to 0.468. Each is shim_stack further from the shoulder. The flange is 0.05 further from the rear face than the 3-prong's, and the tines' front the same 2.34 ahead of the flange's front on both (2.32 on the 3-prong)."}}},{"subject":"sylvan-arms-sa5-pro-left-folder","title":"Sylvan Arms SA5 Pro AR15 Folding Stock Adapter (Opens To The Left)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"maker","value":9.4,"unit":"oz","pm":0.05,"stated":"CNC-machined in the USA from 4140 Steel and only 9.4 ounces","source":{"type":"spec","publisher":"manufacturer","name":"Sylvan Arms, SA5 Pro AR15 Folding Stock Adapter (SKU SA5P; \"Direction of fold\": \"Adapter Opens To The Left\")","url":"https://sylvanarms.com/product/sa5-pro-ar15-folding-stock-adapter/","retrieved":"2026-10-18","via":"harvest"}},{"id":"pa","value":9.4,"unit":"oz","pm":0.05,"stated":"Weight: 9.4 oz","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Sylvan Arms AR-15 & AR-9 Folding Stock Adapter - Gen 5 - Left Folding (SKU SA5P-L, MPN SA5P-L)","url":"https://www.primaryarms.com/https-www.primaryarms.com-sylvan-arms-ar-15-ar-9-folding-stock-adapter-gen-5-left-folding","retrieved":"2026-10-18","via":"harvest"}},{"id":"ar15d","value":9.4,"unit":"oz","pm":0.05,"stated":"Weight 9.4 oz","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, Sylvan Arms AR-15 & AR-9 Folding Stock Adapter - Gen 5 - Left Folding - SA5P-L (MPN SA5P-L, UPC 811313033377; \"Additional information\")","url":"https://ar15discounts.com/products/sylvan-arms-ar-15-ar-9-folding-stock-adapter-gen-5-left-folding/","retrieved":"2026-10-18","via":"harvest"},"note":"The same field's \"Dimensions 8.85 × 6 × 2.5 in\" is a box: the part is not 8.85 in long."}],"adopt":{"from":"maker","reason":"The maker's own figure; both sellers give the same."},"note":"The maker's figure for the adapter; no page says whether the bolt extension in the box is in it. Every seller on file gives the same."},"added_length":{"label":"How far it moves the receiver extension back","kind":"length","measurements":[{"id":"maker","value":1.475,"unit":"in","pm":0.025,"stated":"It depends how the adapter times with the threads in your lower receiver, but it will be between 1.45 and 1.50 inches additional length.","source":{"type":"spec","publisher":"manufacturer","name":"Sylvan Arms, SA5 Pro AR15 Folding Stock Adapter, Q & A (\"How much extra length does this add?\", asked July 24, 2026; answered by the store manager the same day)","url":"https://sylvanarms.com/product/sa5-pro-ar15-folding-stock-adapter/","retrieved":"2026-10-18","via":"harvest"}},{"id":"photo","value":1.484,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder 535513d34cb2 (Sylvan Arms' DSC08599: a rifle standing muzzle up, its right side toward the lens, close; 2048 x 2048)","scaleRef":"the adapter's height across the bore, 0.737 + 1.421 in (.ring_r on Primary Arms' rear view, .body_bottom_below_axis on its open view), 270 px square to the bore","method":"the length on the right face from the castle nut's front (where the lower's green ends, row 777) to the stock half's rear face (where the end plate's flat begins, row 964), 187 px, at the height's scale. ± covers a 2% scale (the height's own readings) and 3 px at each end","via":"harvest"}}],"adopt":{"from":"maker","reason":"The maker's own answer, the middle of its range; the photo, scaled by the part's height, agrees within it."},"note":"It screws into the lower where a receiver extension would, its own castle nut against the lower's rear face, and the extension screws into its rear half as into a lower: the stock half's rear face stands this far behind the lower's. The maker gives a range, as it times with the lower's thread."},"length":{"label":"Its length along the bore (its castle nut's front to the stock half's rear face)","kind":"length","measurements":[{"id":"added","value":1.475,"unit":"in","pm":0.025,"source":{"type":"derived","expr":"{.added_length}","via":"harvest"}}],"note":"The castle nut bears on the lower's rear face (std.ar15.receiver_rear_x) and the stock half's rear face stands where a lower's would: as long as it moves the tube back. Its front thread reaches forward of it into the lower's ring."},"nut_length":{"label":"Its castle nut, front face to rear (along the bore)","kind":"length","measurements":[{"id":"photo","value":0.221,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder 535513d34cb2 (Sylvan Arms' DSC08599: a rifle standing muzzle up, its right side toward the lens, close; 2048 x 2048)","scaleRef":"the length the maker says it adds (.added_length), read along the bore on the right face from the lower's rear face (the castle nut's front) to the stock half's rear face (the end plate's front): 187 px. Its height across the bore, from the ring's top to the face's bottom (.ring_r and .body_bottom_below_axis, the other two photos: 2.158 in), is 270 px square to the bore (the rifle leans 6.7 degrees in the picture): 125 px/in against the length's 126.8, 1.3% apart","method":"28 of the 187 px (rows 777 to 805: the glossy notched ring between the lower's green and the receiver half's front face)","via":"harvest"}}],"note":"A notched ring on the adapter's own front thread, tightened against the lower's rear face (Monadnock Firearms' list: \"Includes a castle nut wrench\"). On the maker's photo of the right side it bears on the lower itself, with no end plate between."},"receiver_half_length":{"label":"The receiver half, front face to where the halves meet","kind":"length","measurements":[{"id":"photo","value":0.568,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder 535513d34cb2 (Sylvan Arms' DSC08599: a rifle standing muzzle up, its right side toward the lens, close; 2048 x 2048)","scaleRef":"the length the maker says it adds (.added_length), read along the bore on the right face from the lower's rear face (the castle nut's front) to the stock half's rear face (the end plate's front): 187 px. Its height across the bore, from the ring's top to the face's bottom (.ring_r and .body_bottom_below_axis, the other two photos: 2.158 in), is 270 px square to the bore (the rifle leans 6.7 degrees in the picture): 125 px/in against the length's 126.8, 1.3% apart","method":"72 of the 187 px (rows 805 to 877: the receiver half's front face to the seam, a straight line across the right face)","via":"harvest"}}],"note":"Where the halves meet is taken as the hinge's plane (.hinge_x): opened flat (e6285ca2177b) their two mating faces lie in one plane side by side, which a seam ahead of or behind the axis would offset by twice its distance."},"stock_half_length":{"label":"The stock half, where the halves meet to its rear face","kind":"length","measurements":[{"id":"rest","value":0.686,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.length} - {.nut_length} - {.receiver_half_length}","via":"harvest"}}],"note":"The rest of the length: 87 of the photo's 187 px (rows 877 to 964), 0.686 at its scale."},"hinge_x":{"label":"The hinge's axis behind the takedown pin","kind":"length","measurements":[{"id":"seam","value":1.914,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"0in - {std.ar15.receiver_rear_x} + {.nut_length} + {.receiver_half_length}","via":"harvest"}}],"note":"In the plane where the halves meet (.receiver_half_length's note): the lower's rear face (the Army's drawing), the castle nut and the receiver half behind it."},"hinge_z":{"label":"The hinge's axis out from the tube's axis, toward the side it folds to (the rifle's left)","kind":"length","measurements":[{"id":"photo","value":1.232,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder e6285ca2177b (Primary Arms' SA5P-L_02: the adapter opened flat, 180 degrees, both mating faces toward a lens behind, right of and above it; 2000 x 1334)","scaleRef":"the faces' plane rectified by the stock half's bore mouth on its mating face (a RANSAC ellipse on its rim's edges, 263.8 x 312.6 px at 170.2 degrees, rms 0.65 px), turned so the receiver half's bore centre (its rim's ellipse, 243.7 x 302.0 px, rms 0.57 px) is level with it, and scaled by the stock half's side away from the hinge standing .ring_r from its bore's centre (1.29 mouth radii there): the mouth comes out 1.142 across, the size of the threaded bore behind it","method":"half the bores' centres' distance, 2.464 in in the faces' plane (opened 180 degrees about the axis the two bores stand twice the axis's distance apart wherever the halves meet along the bore). The hinge's top knuckle's socket head, on the axis, reads 1.227 from the stock half's bore; the receiver half's ring's edge on the hinge side, the face's own edge there, reads 0.72 from its bore, the ring's radius. ± covers the scale (.ring_r's 3.4%) and the photo's perspective (the bottom edges of the two faces read 6 degrees off level in the frame levelled by the bores)","via":"harvest"}}],"note":"Opened flat about the hinge, the two halves' bores stand side by side twice this apart with the hinge midway: read on Primary Arms' open view. The side is the left: on every photo on file the hinge is on the part's left (the receiver half's right face carries the cover plate, the button and a QD socket on the maker's photo of a rifle's right side, 535513d34cb2), the maker's DSC08643 has the stock folded along a rifle's left side, and the maker: \"Folding to the LEFT folds off to the side with out the ejection port.\""},"fold_max":{"label":"How far the hinge turns before its own halves stop it","kind":"angle","measurements":[{"id":"photo","value":180,"unit":"deg","pm":5,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder e6285ca2177b (Primary Arms' SA5P-L_02: the adapter opened flat, 180 degrees, both mating faces toward a lens behind, right of and above it; 2000 x 1334)","scaleRef":"angles: both halves' bore rims read as ellipses of nearly one shape (0.84 and 0.81 of a circle) facing one way","method":"the two halves' mating faces in one plane, side by side","via":"harvest"}}],"note":"Opened flat on Primary Arms' photo the two halves' mating faces lie in one plane side by side, the knuckles between them; no page states an angle and no photo shows it turned past that. How far the stock itself goes on a rifle before it meets the receiver is the build's (the app works it out)."},"width":{"label":"Its width across the rifle, the hinge included","kind":"length","measurements":[{"id":"sum","value":2.222,"unit":"in","pm":0.08,"source":{"type":"derived","expr":"{.ring_r} + {.hinge_z} + {.knuckle_d} / 2","via":"harvest"}}],"note":"The body's side away from the hinge to the knuckles' outer face. The QD socket on the right face stands out beyond it (.qd_proud, assumed)."},"height":{"label":"Its height","kind":"length","measurements":[{"id":"sum","value":2.158,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{.ring_r} + {.body_bottom_below_axis}","via":"harvest"}}]},"bore_thread_crest_d":{"label":"The stock half's threaded bore: its thread's crests (what one sees through it)","kind":"length","measurements":[{"id":"thread","value":1.1453,"unit":"in","pm":0.036,"source":{"type":"derived","expr":"({std.receiver_extension.thread_minor_d} + {std.receiver_extension.thread_major_d}) / 2","via":"harvest"}}],"note":"The scale of the rear view. The receiver extension screws into it as into a lower (\"Standard 1-3/16” x 16 threading\", the maker), so this is a 1 3/16-16 thread in a hole: its crests lie between the extension's own minor and major diameters (the Army's limits). Taken as the middle of the two, ± half their span."},"ring_r":{"label":"The body's ring about the bore: its radius (its top) and its sides' distance from the bore at the bore's height","kind":"length","measurements":[{"id":"photo","value":0.737,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder 87600342169f (Primary Arms' SA5P-L_01: the adapter closed, from behind, left and above; 2000 x 1334)","scaleRef":"the stock half's rear face rectified by its threaded bore's rim (the edge where the bore goes dark, at the thread's crests: an ellipse 213.2 x 338.7 px at 13.2 degrees, fitted to 804 edge points) as .bore_thread_crest_d, and turned 30.9 degrees so the large hole stands under the bore (the two middle holes then level to 0.027 in: the turn is good to about 2.5 degrees)","method":"the silhouette's right edge (the rifle's right) at the bore's height, its widest: 0.737 at 0.000 (0.729 at +0.10, 0.731 at -0.09). ± covers the scale's 3.1%","via":"harvest"}}],"note":"The body is round about the bore above it and flat-sided below (each half). Read at the side away from the hinge, where the rear view's silhouette is the rear face's own edge (the lens is on the hinge's side). Its top's edge reads 0.685 on the same view, along a bright line that is the edge's break catching the light (inside the edge by the break's width); the maker's side photo, scaled by the length added, has the height from the top to the bottom within 1.3% of this plus .body_bottom_below_axis."},"body_bottom_below_axis":{"label":"The halves' mating faces' bottom edge, below the bore's axis","kind":"length","measurements":[{"id":"photo","value":1.421,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder e6285ca2177b (Primary Arms' SA5P-L_02: the adapter opened flat, 180 degrees, both mating faces toward a lens behind, right of and above it; 2000 x 1334)","scaleRef":"the faces' plane rectified by the stock half's bore mouth on its mating face (a RANSAC ellipse on its rim's edges, 263.8 x 312.6 px at 170.2 degrees, rms 0.65 px), turned so the receiver half's bore centre (its rim's ellipse, 243.7 x 302.0 px, rms 0.57 px) is level with it, and scaled by the stock half's side away from the hinge standing .ring_r from its bore's centre (1.29 mouth radii there): the mouth comes out 1.142 across, the size of the threaded bore behind it","method":"the stock half's face's bottom silhouette (the lens is above: the bottom's edge is the face's) from 0.34 in to the far side of the bore to 0.7 to the hinge's, in that frame turned 6 degrees so the edge is level (it reads 1.393 to 1.492 in the frame the bores level). The rear view's lobe reaches 1.409 below the bore (.lobe_r)","via":"harvest"}}]},"corner_r":{"label":"The mating faces' lower corners: their round","kind":"length","measurements":[{"id":"photo","value":0.3,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder e6285ca2177b (Primary Arms' SA5P-L_02: the adapter opened flat, 180 degrees, both mating faces toward a lens behind, right of and above it; 2000 x 1334)","scaleRef":"the faces' plane rectified by the stock half's bore mouth on its mating face (a RANSAC ellipse on its rim's edges, 263.8 x 312.6 px at 170.2 degrees, rms 0.65 px), turned so the receiver half's bore centre (its rim's ellipse, 243.7 x 302.0 px, rms 0.57 px) is level with it, and scaled by the stock half's side away from the hinge standing .ring_r from its bore's centre (1.29 mouth radii there): the mouth comes out 1.142 across, the size of the threaded bore behind it","method":"the stock half's face's far side leaves its straight line 0.95 below the bore and meets the bottom 0.43 from the bore's centre line (silhouette rows 740 to 860)","via":"harvest"}}]},"lobe_centre_below_axis":{"label":"The stock half's rear face: its lower lobe's centre (the large hole's) below the bore's axis","kind":"length","measurements":[{"id":"photo","value":1.045,"unit":"in","pm":0.035,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder 87600342169f (Primary Arms' SA5P-L_01: the adapter closed, from behind, left and above; 2000 x 1334)","scaleRef":"the stock half's rear face rectified by its threaded bore's rim (the edge where the bore goes dark, at the thread's crests: an ellipse 213.2 x 338.7 px at 13.2 degrees, fitted to 804 edge points) as .bore_thread_crest_d, and turned 30.9 degrees so the large hole stands under the bore (the two middle holes then level to 0.027 in: the turn is good to about 2.5 degrees)","method":"the large hole's ellipse (94.1 x 149.4 px) centre in the rectified face","via":"harvest"}}],"note":"The rear face is a teardrop: the ring about the bore and a lobe below it about the large hole, joined by straight sides tangent to both (they lean 20.4 degrees on the photo; tangent lines between the two circles lean 20.9)."},"lobe_r":{"label":"The stock half's rear face: its lower lobe's radius about the large hole","kind":"length","measurements":[{"id":"photo","value":0.37,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder 87600342169f (Primary Arms' SA5P-L_01: the adapter closed, from behind, left and above; 2000 x 1334)","scaleRef":"the stock half's rear face rectified by its threaded bore's rim (the edge where the bore goes dark, at the thread's crests: an ellipse 213.2 x 338.7 px at 13.2 degrees, fitted to 804 edge points) as .bore_thread_crest_d, and turned 30.9 degrees so the large hole stands under the bore (the two middle holes then level to 0.027 in: the turn is good to about 2.5 degrees)","method":"the rectified silhouette's lobe about the large hole's centre: 0.364 at its bottom (1.409 below the bore), 0.372 and 0.389 at 30 and 60 degrees round toward the rifle's right","via":"harvest"}}]},"big_hole_d":{"label":"The stock half's rear face: the large hole (in the lobe, under the bore)","kind":"length","measurements":[{"id":"photo","value":0.505,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder 87600342169f (Primary Arms' SA5P-L_01: the adapter closed, from behind, left and above; 2000 x 1334)","scaleRef":"the stock half's rear face rectified by its threaded bore's rim (the edge where the bore goes dark, at the thread's crests: an ellipse 213.2 x 338.7 px at 13.2 degrees, fitted to 804 edge points) as .bore_thread_crest_d, and turned 30.9 degrees so the large hole stands under the bore (the two middle holes then level to 0.027 in: the turn is good to about 2.5 degrees)","method":"its ellipse's area in the rectified face (94.1 x 149.4 px)","via":"harvest"}}]},"mid_hole_d":{"label":"The stock half's rear face: the two middle holes","kind":"length","measurements":[{"id":"photo","value":0.274,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder 87600342169f (Primary Arms' SA5P-L_01: the adapter closed, from behind, left and above; 2000 x 1334)","scaleRef":"the stock half's rear face rectified by its threaded bore's rim (the edge where the bore goes dark, at the thread's crests: an ellipse 213.2 x 338.7 px at 13.2 degrees, fitted to 804 edge points) as .bore_thread_crest_d, and turned 30.9 degrees so the large hole stands under the bore (the two middle holes then level to 0.027 in: the turn is good to about 2.5 degrees)","method":"their ellipses' areas in the rectified face: 0.278 (the rifle's left) and 0.271 (its right)","via":"harvest"}}]},"mid_hole_apart":{"label":"The stock half's rear face: the middle holes' centres out from the bore's vertical","kind":"length","measurements":[{"id":"photo","value":0.334,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder 87600342169f (Primary Arms' SA5P-L_01: the adapter closed, from behind, left and above; 2000 x 1334)","scaleRef":"the stock half's rear face rectified by its threaded bore's rim (the edge where the bore goes dark, at the thread's crests: an ellipse 213.2 x 338.7 px at 13.2 degrees, fitted to 804 edge points) as .bore_thread_crest_d, and turned 30.9 degrees so the large hole stands under the bore (the two middle holes then level to 0.027 in: the turn is good to about 2.5 degrees)","method":"0.323 to the rifle's left and 0.345 to its right, rectified: their mean","via":"harvest"}}]},"mid_hole_below_axis":{"label":"The stock half's rear face: the middle holes' centres below the bore's axis","kind":"length","measurements":[{"id":"photo","value":0.745,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder 87600342169f (Primary Arms' SA5P-L_01: the adapter closed, from behind, left and above; 2000 x 1334)","scaleRef":"the stock half's rear face rectified by its threaded bore's rim (the edge where the bore goes dark, at the thread's crests: an ellipse 213.2 x 338.7 px at 13.2 degrees, fitted to 804 edge points) as .bore_thread_crest_d, and turned 30.9 degrees so the large hole stands under the bore (the two middle holes then level to 0.027 in: the turn is good to about 2.5 degrees)","method":"0.732 (left) and 0.759 (right), rectified: their mean","via":"harvest"}}]},"small_hole_d":{"label":"The stock half's rear face: the small hole (between the left middle hole and the large one)","kind":"length","measurements":[{"id":"photo","value":0.124,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder 87600342169f (Primary Arms' SA5P-L_01: the adapter closed, from behind, left and above; 2000 x 1334)","scaleRef":"the stock half's rear face rectified by its threaded bore's rim (the edge where the bore goes dark, at the thread's crests: an ellipse 213.2 x 338.7 px at 13.2 degrees, fitted to 804 edge points) as .bore_thread_crest_d, and turned 30.9 degrees so the large hole stands under the bore (the two middle holes then level to 0.027 in: the turn is good to about 2.5 degrees)","method":"its ellipse's area (23.3 x 36.2 px) in the rectified face","via":"harvest"}}]},"small_hole_left":{"label":"The stock half's rear face: the small hole's centre out from the bore's vertical, toward the rifle's left","kind":"length","measurements":[{"id":"photo","value":0.098,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder 87600342169f (Primary Arms' SA5P-L_01: the adapter closed, from behind, left and above; 2000 x 1334)","scaleRef":"the stock half's rear face rectified by its threaded bore's rim (the edge where the bore goes dark, at the thread's crests: an ellipse 213.2 x 338.7 px at 13.2 degrees, fitted to 804 edge points) as .bore_thread_crest_d, and turned 30.9 degrees so the large hole stands under the bore (the two middle holes then level to 0.027 in: the turn is good to about 2.5 degrees)","method":"its centre, rectified","via":"harvest"}}]},"small_hole_below_axis":{"label":"The stock half's rear face: the small hole's centre below the bore's axis","kind":"length","measurements":[{"id":"photo","value":0.718,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder 87600342169f (Primary Arms' SA5P-L_01: the adapter closed, from behind, left and above; 2000 x 1334)","scaleRef":"the stock half's rear face rectified by its threaded bore's rim (the edge where the bore goes dark, at the thread's crests: an ellipse 213.2 x 338.7 px at 13.2 degrees, fitted to 804 edge points) as .bore_thread_crest_d, and turned 30.9 degrees so the large hole stands under the bore (the two middle holes then level to 0.027 in: the turn is good to about 2.5 degrees)","method":"its centre, rectified","via":"harvest"}}]},"big_hole_depth":{"label":"The large hole's depth","kind":"length","measurements":[{"id":"assumed","value":0.4,"unit":"in","pm":0.15,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file looks into it far enough to see its floor (dark on every photo).","via":"harvest"}}]},"mid_hole_depth":{"label":"The middle and small holes' depth","kind":"length","measurements":[{"id":"assumed","value":0.25,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file looks into them far enough to see their floors.","via":"harvest"}}]},"receiver_bore_d":{"label":"The receiver half's bore (what the buffer and the bolt extension pass)","kind":"length","measurements":[{"id":"photo","value":1.079,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder e6285ca2177b (Primary Arms' SA5P-L_02: the adapter opened flat, 180 degrees, both mating faces toward a lens behind, right of and above it; 2000 x 1334)","scaleRef":"the faces' plane rectified by the stock half's bore mouth on its mating face (a RANSAC ellipse on its rim's edges, 263.8 x 312.6 px at 170.2 degrees, rms 0.65 px), turned so the receiver half's bore centre (its rim's ellipse, 243.7 x 302.0 px, rms 0.57 px) is level with it, and scaled by the stock half's side away from the hinge standing .ring_r from its bore's centre (1.29 mouth radii there): the mouth comes out 1.142 across, the size of the threaded bore behind it","method":"its rim's ellipse's area (243.7 x 302.0 px) in the faces' plane","via":"harvest"}}],"note":"Its rim on the mating face; further in, Primary Arms' open view shows a ring with flats (the front thread's own end), which is drawn at the tube's bore (std.receiver_extension.bore_d)."},"block_top_below_axis":{"label":"The hinge's blocks: their top below the bore's axis (the floor of the gap between the halves' rings)","kind":"length","measurements":[{"id":"photo","value":0.217,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder e6285ca2177b (Primary Arms' SA5P-L_02: the adapter opened flat, 180 degrees, both mating faces toward a lens behind, right of and above it; 2000 x 1334)","scaleRef":"the faces' plane rectified by the stock half's bore mouth on its mating face (a RANSAC ellipse on its rim's edges, 263.8 x 312.6 px at 170.2 degrees, rms 0.65 px), turned so the receiver half's bore centre (its rim's ellipse, 243.7 x 302.0 px, rms 0.57 px) is level with it, and scaled by the stock half's side away from the hinge standing .ring_r from its bore's centre (1.29 mouth radii there): the mouth comes out 1.142 across, the size of the threaded bore behind it","method":"where the white gap between the rings ends (rows 598 to 615, columns 910 to 1000)","via":"harvest"}}],"note":"Below the rings each half carries a block out to the hinge on the rifle's left; opened flat, the white gap between the two rings ends on their top."},"knuckle_d":{"label":"The hinge's knuckles and its knurled collar: their diameter","kind":"length","measurements":[{"id":"photo","value":0.505,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder e6285ca2177b (Primary Arms' SA5P-L_02: the adapter opened flat, 180 degrees, both mating faces toward a lens behind, right of and above it; 2000 x 1334)","scaleRef":"the faces' plane rectified by the stock half's bore mouth on its mating face (a RANSAC ellipse on its rim's edges, 263.8 x 312.6 px at 170.2 degrees, rms 0.65 px), turned so the receiver half's bore centre (its rim's ellipse, 243.7 x 302.0 px, rms 0.57 px) is level with it, and scaled by the stock half's side away from the hinge standing .ring_r from its bore's centre (1.29 mouth radii there): the mouth comes out 1.142 across, the size of the threaded bore behind it","method":"the top knuckle's silhouette across, columns 850 to 969 (119 px; the knurled collar under it 118 px)","via":"harvest"}}]},"top_knuckle_bottom_below_axis":{"label":"The top knuckle's lower end (the knurled collar's window's top) below the bore's axis","kind":"length","measurements":[{"id":"photo","value":0.579,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder e6285ca2177b (Primary Arms' SA5P-L_02: the adapter opened flat, 180 degrees, both mating faces toward a lens behind, right of and above it; 2000 x 1334)","scaleRef":"the faces' plane rectified by the stock half's bore mouth on its mating face (a RANSAC ellipse on its rim's edges, 263.8 x 312.6 px at 170.2 degrees, rms 0.65 px), turned so the receiver half's bore centre (its rim's ellipse, 243.7 x 302.0 px, rms 0.57 px) is level with it, and scaled by the stock half's side away from the hinge standing .ring_r from its bore's centre (1.29 mouth radii there): the mouth comes out 1.142 across, the size of the threaded bore behind it","method":"the window's top edge, row 703 at column 880","via":"harvest"}}],"note":"Top to bottom on the axis: the top knuckle from the blocks' top down to here, the knurled collar in a window to .collar_bottom_below_axis, the bottom knuckle from there to the faces' bottom. The top knuckle carries the hinge bolt's socket head."},"collar_bottom_below_axis":{"label":"The knurled collar's window's lower end (the bottom knuckle's top) below the bore's axis","kind":"length","measurements":[{"id":"photo","value":1.109,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder e6285ca2177b (Primary Arms' SA5P-L_02: the adapter opened flat, 180 degrees, both mating faces toward a lens behind, right of and above it; 2000 x 1334)","scaleRef":"the faces' plane rectified by the stock half's bore mouth on its mating face (a RANSAC ellipse on its rim's edges, 263.8 x 312.6 px at 170.2 degrees, rms 0.65 px), turned so the receiver half's bore centre (its rim's ellipse, 243.7 x 302.0 px, rms 0.57 px) is level with it, and scaled by the stock half's side away from the hinge standing .ring_r from its bore's centre (1.29 mouth radii there): the mouth comes out 1.142 across, the size of the threaded bore behind it","method":"the ledge under the collar, its top edge at row 847 at column 880","via":"harvest"}}]},"bolt_head_d":{"label":"The hinge bolt's socket head in the top knuckle's top: its diameter","kind":"length","measurements":[{"id":"photo","value":0.26,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder e6285ca2177b (Primary Arms' SA5P-L_02: the adapter opened flat, 180 degrees, both mating faces toward a lens behind, right of and above it; 2000 x 1334)","scaleRef":"the faces' plane rectified by the stock half's bore mouth on its mating face (a RANSAC ellipse on its rim's edges, 263.8 x 312.6 px at 170.2 degrees, rms 0.65 px), turned so the receiver half's bore centre (its rim's ellipse, 243.7 x 302.0 px, rms 0.57 px) is level with it, and scaled by the stock half's side away from the hinge standing .ring_r from its bore's centre (1.29 mouth radii there): the mouth comes out 1.142 across, the size of the threaded bore behind it","method":"the head's top across (about 62 px), seen from above the knuckle","via":"harvest"}}]},"bolt_socket":{"label":"The hinge bolt's hex socket, across its flats","kind":"length","measurements":[{"id":"photo","value":0.1,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder e6285ca2177b (Primary Arms' SA5P-L_02: the adapter opened flat, 180 degrees, both mating faces toward a lens behind, right of and above it; 2000 x 1334)","scaleRef":"the faces' plane rectified by the stock half's bore mouth on its mating face (a RANSAC ellipse on its rim's edges, 263.8 x 312.6 px at 170.2 degrees, rms 0.65 px), turned so the receiver half's bore centre (its rim's ellipse, 243.7 x 302.0 px, rms 0.57 px) is level with it, and scaled by the stock half's side away from the hinge standing .ring_r from its bore's centre (1.29 mouth radii there): the mouth comes out 1.142 across, the size of the threaded bore behind it","method":"the dark socket across (about 24 px)","via":"harvest"}}]},"bolt_head_recess":{"label":"How far the bolt's head is sunk under the knuckle's top","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the photos see the head's top and the knuckle's rim round it from above, not in profile.","via":"harvest"}}]},"bolt_head_height":{"label":"The bolt head's height in its counterbore","kind":"length","measurements":[{"id":"assumed","value":0.08,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows it in profile.","via":"harvest"}}]},"bolt_socket_depth":{"label":"The bolt head's hex socket's depth","kind":"length","measurements":[{"id":"assumed","value":0.06,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: dark on every photo.","via":"harvest"}}]},"nut_d":{"label":"The castle nut's outside diameter","kind":"length","measurements":[{"id":"photo","value":1.42,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder 535513d34cb2 (Sylvan Arms' DSC08599: a rifle standing muzzle up, its right side toward the lens, close; 2048 x 2048)","scaleRef":"the length the maker says it adds (.added_length), read along the bore on the right face from the lower's rear face (the castle nut's front) to the stock half's rear face (the end plate's front): 187 px. Its height across the bore, from the ring's top to the face's bottom (.ring_r and .body_bottom_below_axis, the other two photos: 2.158 in), is 270 px square to the bore (the rifle leans 6.7 degrees in the picture): 125 px/in against the length's 126.8, 1.3% apart","method":"its top edge (the rifle's top) 3 px, 0.025 in, under the body's top beside it (the rifle's lean taken out): twice .ring_r less that. Its lower edge is behind the grip","via":"harvest"}}]},"nut_notches":{"label":"The castle nut's notches","kind":"count","measurements":[{"id":"assumed","value":4,"unit":"count","source":{"type":"derived","basis":"An assumption for the drawing, not a count: four at 90 degrees, as two seen a quarter turn apart in each of two views from opposite corners allow.","via":"harvest"}}],"note":"Not counted: no photo shows the whole turn. Two are seen 90 degrees apart from the front and right (AR15Discounts' 307151, 1191d2a72083), two from behind and left (e6285ca2177b, 87600342169f)."},"nut_notch_width":{"label":"The castle nut's notches: their width","kind":"length","measurements":[{"id":"assumed","value":0.14,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the notches are seen only obliquely (about a tenth of the nut's circumference on 1191d2a72083).","via":"harvest"}}]},"nut_notch_depth":{"label":"The castle nut's notches: their depth in from its rim (each through its length)","kind":"length","measurements":[{"id":"assumed","value":0.06,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows them in profile.","via":"harvest"}}]},"stock_block_length":{"label":"The stock half's hinge block: how far it reaches back from where the halves meet","kind":"length","measurements":[{"id":"assumed","value":0.5,"unit":"in","pm":0.15,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the rear view sees the block's outer face end on, at another depth than the rear face the photo is scaled in.","via":"harvest"}}],"note":"Under the ring on the rifle's left the stock half carries a block out to the hinge (87600342169f has its outer face behind the knuckles, a little forward of the rear face); where it ends along the bore isn't read on any view."},"tab_out":{"label":"The stock half's locking tab (on its mating face): its centre out from the bore's vertical, toward the rifle's right","kind":"length","measurements":[{"id":"photo","value":0.351,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder e6285ca2177b (Primary Arms' SA5P-L_02: the adapter opened flat, 180 degrees, both mating faces toward a lens behind, right of and above it; 2000 x 1334)","scaleRef":"the faces' plane rectified by the stock half's bore mouth on its mating face (a RANSAC ellipse on its rim's edges, 263.8 x 312.6 px at 170.2 degrees, rms 0.65 px), turned so the receiver half's bore centre (its rim's ellipse, 243.7 x 302.0 px, rms 0.57 px) is level with it, and scaled by the stock half's side away from the hinge standing .ring_r from its bore's centre (1.29 mouth radii there): the mouth comes out 1.142 across, the size of the threaded bore behind it","method":"its base's centre (its end face's centre, 501, 706 px, moved back along the depth's direction by its height off the face)","via":"harvest"}}],"note":"A block standing out of the stock half's mating face low on the side away from the hinge; closed, it goes into a slot in the receiver half's rear face beside the release button (\"Improved Locking Mechanism\", the maker). Read on Primary Arms' open view: its end face and where its side meets the face."},"tab_below_axis":{"label":"The stock half's locking tab: its centre below the bore's axis","kind":"length","measurements":[{"id":"photo","value":0.721,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder e6285ca2177b (Primary Arms' SA5P-L_02: the adapter opened flat, 180 degrees, both mating faces toward a lens behind, right of and above it; 2000 x 1334)","scaleRef":"the faces' plane rectified by the stock half's bore mouth on its mating face (a RANSAC ellipse on its rim's edges, 263.8 x 312.6 px at 170.2 degrees, rms 0.65 px), turned so the receiver half's bore centre (its rim's ellipse, 243.7 x 302.0 px, rms 0.57 px) is level with it, and scaled by the stock half's side away from the hinge standing .ring_r from its bore's centre (1.29 mouth radii there): the mouth comes out 1.142 across, the size of the threaded bore behind it","method":"as .tab_out","via":"harvest"}}]},"tab_width":{"label":"The stock half's locking tab: its width across the rifle","kind":"length","measurements":[{"id":"photo","value":0.16,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder e6285ca2177b (Primary Arms' SA5P-L_02: the adapter opened flat, 180 degrees, both mating faces toward a lens behind, right of and above it; 2000 x 1334)","scaleRef":"the faces' plane rectified by the stock half's bore mouth on its mating face (a RANSAC ellipse on its rim's edges, 263.8 x 312.6 px at 170.2 degrees, rms 0.65 px), turned so the receiver half's bore centre (its rim's ellipse, 243.7 x 302.0 px, rms 0.57 px) is level with it, and scaled by the stock half's side away from the hinge standing .ring_r from its bore's centre (1.29 mouth radii there): the mouth comes out 1.142 across, the size of the threaded bore behind it","method":"its end face across, 38 px","via":"harvest"}}]},"tab_height":{"label":"The stock half's locking tab: its height","kind":"length","measurements":[{"id":"photo","value":0.39,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder e6285ca2177b (Primary Arms' SA5P-L_02: the adapter opened flat, 180 degrees, both mating faces toward a lens behind, right of and above it; 2000 x 1334)","scaleRef":"the faces' plane rectified by the stock half's bore mouth on its mating face (a RANSAC ellipse on its rim's edges, 263.8 x 312.6 px at 170.2 degrees, rms 0.65 px), turned so the receiver half's bore centre (its rim's ellipse, 243.7 x 302.0 px, rms 0.57 px) is level with it, and scaled by the stock half's side away from the hinge standing .ring_r from its bore's centre (1.29 mouth radii there): the mouth comes out 1.142 across, the size of the threaded bore behind it","method":"its end face up and down, rows 653 to 760","via":"harvest"}}]},"tab_proud":{"label":"The stock half's locking tab: how far it stands out of the face","kind":"length","measurements":[{"id":"photo","value":0.17,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder e6285ca2177b (Primary Arms' SA5P-L_02: the adapter opened flat, 180 degrees, both mating faces toward a lens behind, right of and above it; 2000 x 1334)","scaleRef":"the depth's direction in the photo: the receiver half's front thread, 1.245 in from its face to its end, runs (222, -100) px an inch","method":"its end face stands 38 px off its base along that direction","via":"harvest"}}]},"slot_out":{"label":"The receiver half's slot for the locking tab (its rear face): its centre out from the bore's vertical, toward the rifle's right","kind":"length","measurements":[{"id":"photo","value":0.43,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder e6285ca2177b (Primary Arms' SA5P-L_02: the adapter opened flat, 180 degrees, both mating faces toward a lens behind, right of and above it; 2000 x 1334)","scaleRef":"the faces' plane rectified by the stock half's bore mouth on its mating face (a RANSAC ellipse on its rim's edges, 263.8 x 312.6 px at 170.2 degrees, rms 0.65 px), turned so the receiver half's bore centre (its rim's ellipse, 243.7 x 302.0 px, rms 0.57 px) is level with it, and scaled by the stock half's side away from the hinge standing .ring_r from its bore's centre (1.29 mouth radii there): the mouth comes out 1.142 across, the size of the threaded bore behind it","method":"the oval slot's centre (1290, 825 px) against the receiver half's bore's","via":"harvest"}}],"note":"Read on its own: 0.08 in further out than the tab it takes and 0.07 lower; the pocket drawn takes in both."},"slot_below_axis":{"label":"The receiver half's slot for the locking tab: its centre below the bore's axis","kind":"length","measurements":[{"id":"photo","value":0.79,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder e6285ca2177b (Primary Arms' SA5P-L_02: the adapter opened flat, 180 degrees, both mating faces toward a lens behind, right of and above it; 2000 x 1334)","scaleRef":"the faces' plane rectified by the stock half's bore mouth on its mating face (a RANSAC ellipse on its rim's edges, 263.8 x 312.6 px at 170.2 degrees, rms 0.65 px), turned so the receiver half's bore centre (its rim's ellipse, 243.7 x 302.0 px, rms 0.57 px) is level with it, and scaled by the stock half's side away from the hinge standing .ring_r from its bore's centre (1.29 mouth radii there): the mouth comes out 1.142 across, the size of the threaded bore behind it","method":"as .slot_out","via":"harvest"}}]},"rear_screw_out":{"label":"The receiver half's rear face: the socket screw's centre out toward the rifle's right","kind":"length","measurements":[{"id":"photo","value":0.578,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder e6285ca2177b (Primary Arms' SA5P-L_02: the adapter opened flat, 180 degrees, both mating faces toward a lens behind, right of and above it; 2000 x 1334)","scaleRef":"the faces' plane rectified by the stock half's bore mouth on its mating face (a RANSAC ellipse on its rim's edges, 263.8 x 312.6 px at 170.2 degrees, rms 0.65 px), turned so the receiver half's bore centre (its rim's ellipse, 243.7 x 302.0 px, rms 0.57 px) is level with it, and scaled by the stock half's side away from the hinge standing .ring_r from its bore's centre (1.29 mouth radii there): the mouth comes out 1.142 across, the size of the threaded bore behind it","method":"its head's centre (1330, 735 px) against the bore's","via":"harvest"}}],"note":"Three things on the receiver half's mating face besides the slot, seen when folded: a socket screw above the slot, a large hex socket under the bore and a round hole toward the hinge (Primary Arms' open view)."},"rear_screw_below_axis":{"label":"The receiver half's rear face: the socket screw's centre below the bore's axis","kind":"length","measurements":[{"id":"photo","value":0.441,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder e6285ca2177b (Primary Arms' SA5P-L_02: the adapter opened flat, 180 degrees, both mating faces toward a lens behind, right of and above it; 2000 x 1334)","scaleRef":"the faces' plane rectified by the stock half's bore mouth on its mating face (a RANSAC ellipse on its rim's edges, 263.8 x 312.6 px at 170.2 degrees, rms 0.65 px), turned so the receiver half's bore centre (its rim's ellipse, 243.7 x 302.0 px, rms 0.57 px) is level with it, and scaled by the stock half's side away from the hinge standing .ring_r from its bore's centre (1.29 mouth radii there): the mouth comes out 1.142 across, the size of the threaded bore behind it","method":"as .rear_screw_out","via":"harvest"}}]},"rear_screw_d":{"label":"The receiver half's rear face: the socket screw's head","kind":"length","measurements":[{"id":"photo","value":0.19,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder e6285ca2177b (Primary Arms' SA5P-L_02: the adapter opened flat, 180 degrees, both mating faces toward a lens behind, right of and above it; 2000 x 1334)","scaleRef":"the faces' plane rectified by the stock half's bore mouth on its mating face (a RANSAC ellipse on its rim's edges, 263.8 x 312.6 px at 170.2 degrees, rms 0.65 px), turned so the receiver half's bore centre (its rim's ellipse, 243.7 x 302.0 px, rms 0.57 px) is level with it, and scaled by the stock half's side away from the hinge standing .ring_r from its bore's centre (1.29 mouth radii there): the mouth comes out 1.142 across, the size of the threaded bore behind it","method":"its head across, about 45 px","via":"harvest"}}]},"rear_hex_out":{"label":"The receiver half's rear face: the large hex socket's centre out toward the rifle's right","kind":"length","measurements":[{"id":"photo","value":0.065,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder e6285ca2177b (Primary Arms' SA5P-L_02: the adapter opened flat, 180 degrees, both mating faces toward a lens behind, right of and above it; 2000 x 1334)","scaleRef":"the faces' plane rectified by the stock half's bore mouth on its mating face (a RANSAC ellipse on its rim's edges, 263.8 x 312.6 px at 170.2 degrees, rms 0.65 px), turned so the receiver half's bore centre (its rim's ellipse, 243.7 x 302.0 px, rms 0.57 px) is level with it, and scaled by the stock half's side away from the hinge standing .ring_r from its bore's centre (1.29 mouth radii there): the mouth comes out 1.142 across, the size of the threaded bore behind it","method":"its centre (1200, 890 px) against the bore's","via":"harvest"}}]},"rear_hex_below_axis":{"label":"The receiver half's rear face: the large hex socket's centre below the bore's axis","kind":"length","measurements":[{"id":"photo","value":1.083,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder e6285ca2177b (Primary Arms' SA5P-L_02: the adapter opened flat, 180 degrees, both mating faces toward a lens behind, right of and above it; 2000 x 1334)","scaleRef":"the faces' plane rectified by the stock half's bore mouth on its mating face (a RANSAC ellipse on its rim's edges, 263.8 x 312.6 px at 170.2 degrees, rms 0.65 px), turned so the receiver half's bore centre (its rim's ellipse, 243.7 x 302.0 px, rms 0.57 px) is level with it, and scaled by the stock half's side away from the hinge standing .ring_r from its bore's centre (1.29 mouth radii there): the mouth comes out 1.142 across, the size of the threaded bore behind it","method":"as .rear_hex_out","via":"harvest"}}]},"rear_hex_d":{"label":"The receiver half's rear face: the large hex socket's bore","kind":"length","measurements":[{"id":"photo","value":0.26,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder e6285ca2177b (Primary Arms' SA5P-L_02: the adapter opened flat, 180 degrees, both mating faces toward a lens behind, right of and above it; 2000 x 1334)","scaleRef":"the faces' plane rectified by the stock half's bore mouth on its mating face (a RANSAC ellipse on its rim's edges, 263.8 x 312.6 px at 170.2 degrees, rms 0.65 px), turned so the receiver half's bore centre (its rim's ellipse, 243.7 x 302.0 px, rms 0.57 px) is level with it, and scaled by the stock half's side away from the hinge standing .ring_r from its bore's centre (1.29 mouth radii there): the mouth comes out 1.142 across, the size of the threaded bore behind it","method":"its rim across, about 60 px","via":"harvest"}}]},"rear_hole_in":{"label":"The receiver half's rear face: the round hole's centre out toward the hinge (the rifle's left)","kind":"length","measurements":[{"id":"photo","value":0.371,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder e6285ca2177b (Primary Arms' SA5P-L_02: the adapter opened flat, 180 degrees, both mating faces toward a lens behind, right of and above it; 2000 x 1334)","scaleRef":"the faces' plane rectified by the stock half's bore mouth on its mating face (a RANSAC ellipse on its rim's edges, 263.8 x 312.6 px at 170.2 degrees, rms 0.65 px), turned so the receiver half's bore centre (its rim's ellipse, 243.7 x 302.0 px, rms 0.57 px) is level with it, and scaled by the stock half's side away from the hinge standing .ring_r from its bore's centre (1.29 mouth radii there): the mouth comes out 1.142 across, the size of the threaded bore behind it","method":"its centre (1100, 860 px) against the bore's","via":"harvest"}}]},"rear_hole_below_axis":{"label":"The receiver half's rear face: the round hole's centre below the bore's axis","kind":"length","measurements":[{"id":"photo","value":1.03,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder e6285ca2177b (Primary Arms' SA5P-L_02: the adapter opened flat, 180 degrees, both mating faces toward a lens behind, right of and above it; 2000 x 1334)","scaleRef":"the faces' plane rectified by the stock half's bore mouth on its mating face (a RANSAC ellipse on its rim's edges, 263.8 x 312.6 px at 170.2 degrees, rms 0.65 px), turned so the receiver half's bore centre (its rim's ellipse, 243.7 x 302.0 px, rms 0.57 px) is level with it, and scaled by the stock half's side away from the hinge standing .ring_r from its bore's centre (1.29 mouth radii there): the mouth comes out 1.142 across, the size of the threaded bore behind it","method":"as .rear_hole_in","via":"harvest"}}]},"rear_hole_d":{"label":"The receiver half's rear face: the round hole","kind":"length","measurements":[{"id":"photo","value":0.21,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder e6285ca2177b (Primary Arms' SA5P-L_02: the adapter opened flat, 180 degrees, both mating faces toward a lens behind, right of and above it; 2000 x 1334)","scaleRef":"the faces' plane rectified by the stock half's bore mouth on its mating face (a RANSAC ellipse on its rim's edges, 263.8 x 312.6 px at 170.2 degrees, rms 0.65 px), turned so the receiver half's bore centre (its rim's ellipse, 243.7 x 302.0 px, rms 0.57 px) is level with it, and scaled by the stock half's side away from the hinge standing .ring_r from its bore's centre (1.29 mouth radii there): the mouth comes out 1.142 across, the size of the threaded bore behind it","method":"its rim across, about 50 px","via":"harvest"}}]},"face_hole_depth":{"label":"The mating faces' holes, the tab's slot and the screw's counterbore: their depth","kind":"length","measurements":[{"id":"assumed","value":0.25,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: dark on the photo.","via":"harvest"}}]},"plate_front":{"label":"The right face's cover plate: its front end behind the receiver half's front face","kind":"length","measurements":[{"id":"photo","value":0.134,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder 535513d34cb2 (Sylvan Arms' DSC08599: a rifle standing muzzle up, its right side toward the lens, close; 2048 x 2048)","scaleRef":"the length the maker says it adds (.added_length), read along the bore on the right face from the lower's rear face (the castle nut's front) to the stock half's rear face (the end plate's front): 187 px. Its height across the bore, from the ring's top to the face's bottom (.ring_r and .body_bottom_below_axis, the other two photos: 2.158 in), is 270 px square to the bore (the rifle leans 6.7 degrees in the picture): 125 px/in against the length's 126.8, 1.3% apart","method":"rows 805 to 822","via":"harvest"}}],"note":"A rounded plate on the receiver half's right face (the release's cover), its lower end under the button."},"plate_length":{"label":"The right face's cover plate: its length along the bore","kind":"length","measurements":[{"id":"photo","value":0.42,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder 535513d34cb2 (Sylvan Arms' DSC08599: a rifle standing muzzle up, its right side toward the lens, close; 2048 x 2048)","scaleRef":"the length the maker says it adds (.added_length), read along the bore on the right face from the lower's rear face (the castle nut's front) to the stock half's rear face (the end plate's front): 187 px. Its height across the bore, from the ring's top to the face's bottom (.ring_r and .body_bottom_below_axis, the other two photos: 2.158 in), is 270 px square to the bore (the rifle leans 6.7 degrees in the picture): 125 px/in against the length's 126.8, 1.3% apart","method":"rows 822 to 875","via":"harvest"}}]},"plate_top":{"label":"The right face's cover plate: its upper end above the bore's axis","kind":"length","measurements":[{"id":"photo","value":0.06,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder 535513d34cb2 (Sylvan Arms' DSC08599: a rifle standing muzzle up, its right side toward the lens, close; 2048 x 2048)","scaleRef":"the length the maker says it adds (.added_length), read along the bore on the right face from the lower's rear face (the castle nut's front) to the stock half's rear face (the end plate's front): 187 px. Its height across the bore, from the ring's top to the face's bottom (.ring_r and .body_bottom_below_axis, the other two photos: 2.158 in), is 270 px square to the bore (the rifle leans 6.7 degrees in the picture): 125 px/in against the length's 126.8, 1.3% apart","method":"0.674 under the body's top (column 857 against 772, the rifle's lean taken out), less .ring_r's 0.737","via":"harvest"}}]},"plate_bottom_below_axis":{"label":"The right face's cover plate: its lower end below the bore's axis","kind":"length","measurements":[{"id":"photo","value":0.8,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder 535513d34cb2 (Sylvan Arms' DSC08599: a rifle standing muzzle up, its right side toward the lens, close; 2048 x 2048)","scaleRef":"the length the maker says it adds (.added_length), read along the bore on the right face from the lower's rear face (the castle nut's front) to the stock half's rear face (the end plate's front): 187 px. Its height across the bore, from the ring's top to the face's bottom (.ring_r and .body_bottom_below_axis, the other two photos: 2.158 in), is 270 px square to the bore (the rifle leans 6.7 degrees in the picture): 125 px/in against the length's 126.8, 1.3% apart","method":"its rounded lower end round the button, column 970: 1.567 under the body's top","via":"harvest"}}]},"plate_proud":{"label":"The cover plate's thickness proud of the face","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows it in profile.","via":"harvest"}}]},"button_d":{"label":"The release button's head (in the cover plate's lower end)","kind":"length","measurements":[{"id":"photo","value":0.28,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder 535513d34cb2 (Sylvan Arms' DSC08599: a rifle standing muzzle up, its right side toward the lens, close; 2048 x 2048)","scaleRef":"the length the maker says it adds (.added_length), read along the bore on the right face from the lower's rear face (the castle nut's front) to the stock half's rear face (the end plate's front): 187 px. Its height across the bore, from the ring's top to the face's bottom (.ring_r and .body_bottom_below_axis, the other two photos: 2.158 in), is 270 px square to the bore (the rifle leans 6.7 degrees in the picture): 125 px/in against the length's 126.8, 1.3% apart","method":"its round head, 36 px across","via":"harvest"}}]},"button_below_axis":{"label":"The release button's centre below the bore's axis","kind":"length","measurements":[{"id":"photo","value":0.68,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder 535513d34cb2 (Sylvan Arms' DSC08599: a rifle standing muzzle up, its right side toward the lens, close; 2048 x 2048)","scaleRef":"the length the maker says it adds (.added_length), read along the bore on the right face from the lower's rear face (the castle nut's front) to the stock half's rear face (the end plate's front): 187 px. Its height across the bore, from the ring's top to the face's bottom (.ring_r and .body_bottom_below_axis, the other two photos: 2.158 in), is 270 px square to the bore (the rifle leans 6.7 degrees in the picture): 125 px/in against the length's 126.8, 1.3% apart","method":"column 952: 1.42 under the body's top, less .ring_r","via":"harvest"}}]},"button_behind_front":{"label":"The release button's centre behind the receiver half's front face","kind":"length","measurements":[{"id":"photo","value":0.39,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder 535513d34cb2 (Sylvan Arms' DSC08599: a rifle standing muzzle up, its right side toward the lens, close; 2048 x 2048)","scaleRef":"the length the maker says it adds (.added_length), read along the bore on the right face from the lower's rear face (the castle nut's front) to the stock half's rear face (the end plate's front): 187 px. Its height across the bore, from the ring's top to the face's bottom (.ring_r and .body_bottom_below_axis, the other two photos: 2.158 in), is 270 px square to the bore (the rifle leans 6.7 degrees in the picture): 125 px/in against the length's 126.8, 1.3% apart","method":"row 855 against the front face's 805","via":"harvest"}}]},"button_proud":{"label":"How far the button's head stands out of the cover plate","kind":"length","measurements":[{"id":"assumed","value":0.06,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the side photos see its face; Primary Arms' open view has the pin pushed out of it (0.4 in or more), as it is when the stock is open to fold.","via":"harvest"}}]},"qd_d":{"label":"The right face's QD socket: its outside diameter","kind":"length","measurements":[{"id":"photo","value":0.44,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder 535513d34cb2 (Sylvan Arms' DSC08599: a rifle standing muzzle up, its right side toward the lens, close; 2048 x 2048)","scaleRef":"the length the maker says it adds (.added_length), read along the bore on the right face from the lower's rear face (the castle nut's front) to the stock half's rear face (the end plate's front): 187 px. Its height across the bore, from the ring's top to the face's bottom (.ring_r and .body_bottom_below_axis, the other two photos: 2.158 in), is 270 px square to the bore (the rifle leans 6.7 degrees in the picture): 125 px/in against the length's 126.8, 1.3% apart","method":"its boss's round end, 56 px across","via":"harvest"}}],"note":"\"2 QD attachment points\" (the maker): one in a boss out of the receiver half's right face, low, by the seam; the other is taken as the large hole in the stock half's rear lobe."},"qd_bore_d":{"label":"The right face's QD socket: its bore","kind":"length","measurements":[{"id":"photo","value":0.31,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder 535513d34cb2 (Sylvan Arms' DSC08599: a rifle standing muzzle up, its right side toward the lens, close; 2048 x 2048)","scaleRef":"the length the maker says it adds (.added_length), read along the bore on the right face from the lower's rear face (the castle nut's front) to the stock half's rear face (the end plate's front): 187 px. Its height across the bore, from the ring's top to the face's bottom (.ring_r and .body_bottom_below_axis, the other two photos: 2.158 in), is 270 px square to the bore (the rifle leans 6.7 degrees in the picture): 125 px/in against the length's 126.8, 1.3% apart","method":"the dark bore in its end, 40 px across","via":"harvest"}}]},"qd_below_axis":{"label":"The right face's QD socket: its centre below the bore's axis","kind":"length","measurements":[{"id":"photo","value":1.2,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder 535513d34cb2 (Sylvan Arms' DSC08599: a rifle standing muzzle up, its right side toward the lens, close; 2048 x 2048)","scaleRef":"the length the maker says it adds (.added_length), read along the bore on the right face from the lower's rear face (the castle nut's front) to the stock half's rear face (the end plate's front): 187 px. Its height across the bore, from the ring's top to the face's bottom (.ring_r and .body_bottom_below_axis, the other two photos: 2.158 in), is 270 px square to the bore (the rifle leans 6.7 degrees in the picture): 125 px/in against the length's 126.8, 1.3% apart","method":"column 1018: 1.94 under the body's top, less .ring_r","via":"harvest"}}]},"qd_behind_front":{"label":"The right face's QD socket: its centre behind the receiver half's front face","kind":"length","measurements":[{"id":"photo","value":0.45,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-left-folder 535513d34cb2 (Sylvan Arms' DSC08599: a rifle standing muzzle up, its right side toward the lens, close; 2048 x 2048)","scaleRef":"the length the maker says it adds (.added_length), read along the bore on the right face from the lower's rear face (the castle nut's front) to the stock half's rear face (the end plate's front): 187 px. Its height across the bore, from the ring's top to the face's bottom (.ring_r and .body_bottom_below_axis, the other two photos: 2.158 in), is 270 px square to the bore (the rifle leans 6.7 degrees in the picture): 125 px/in against the length's 126.8, 1.3% apart","method":"row 862 against the front face's 805","via":"harvest"}}]},"qd_proud":{"label":"How far the QD socket's boss stands out of the right face","kind":"length","measurements":[{"id":"assumed","value":0.2,"unit":"in","pm":0.08,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the photos see the boss end on (535513d34cb2) or obliquely (1191d2a72083, e6285ca2177b), where it stands out about half its diameter.","via":"harvest"}}]},"qd_depth":{"label":"The QD sockets' bore depth","kind":"length","measurements":[{"id":"assumed","value":0.3,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: dark on every photo.","via":"harvest"}}]},"ext_pilot_length":{"label":"The bolt extension: the end that goes into the carrier (its O-ring end), to its shoulder","kind":"length","measurements":[{"id":"photo","value":0.512,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-right-folder 0f82a51c8958 (Monadnock Firearms' picture for SA5P-R, the distributor's IQSA5PR-1, which is the same photograph as its IQSA5PL-1 for the left one: a LEFT folder, closed, from behind and right, with the bolt extension standing beside it; 1000 x 1000)","scaleRef":"the extension's length behind its shoulder (290.1 px along it) as .added_length: 196.7 px/in","method":"its top face's centre (row 282) to the shoulder's (380), 98 px","via":"harvest"}}],"note":"The extension (\"Includes a 1045 Steel Bolt Extension\") stands upright beside the adapter on the distributor's photo, seen a little from above (its top face an ellipse 0.23 of its width: 13.5 degrees; lengths read along it are taken over cos 13.5). Scaled so that what stands behind its shoulder (the body and the neck) is the length the adapter adds, as it must be to put the buffer where it would rest without the adapter: at that scale its O-ring end is 0.610 across, under the carrier's 5/8 in bore (the maker: \"9mm bolt carriers with standard sizing, 5/8 ID (.625) can use the included bolt extension\"). The adapter's rear face's bore in the same photo, nearer the lens, gives a scale 14% larger."},"ext_pilot_d":{"label":"The bolt extension: its O-ring end's diameter","kind":"length","measurements":[{"id":"photo","value":0.61,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-right-folder 0f82a51c8958 (Monadnock Firearms' picture for SA5P-R, the distributor's IQSA5PR-1, which is the same photograph as its IQSA5PL-1 for the left one: a LEFT folder, closed, from behind and right, with the bolt extension standing beside it; 1000 x 1000)","scaleRef":"196.7 px/in (.ext_pilot_length's note)","method":"120 px across; the O-rings in its three grooves stand flush with it","via":"harvest"}}]},"ext_body_length":{"label":"The bolt extension: its body, shoulder to its rear step","kind":"length","measurements":[{"id":"photo","value":0.743,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-right-folder 0f82a51c8958 (Monadnock Firearms' picture for SA5P-R, the distributor's IQSA5PR-1, which is the same photograph as its IQSA5PL-1 for the left one: a LEFT folder, closed, from behind and right, with the bolt extension standing beside it; 1000 x 1000)","scaleRef":"196.7 px/in (.ext_pilot_length's note)","method":"rows 380 to 522, 142 px along","via":"harvest"}}]},"ext_body_d":{"label":"The bolt extension: its body's diameter","kind":"length","measurements":[{"id":"photo","value":0.737,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-right-folder 0f82a51c8958 (Monadnock Firearms' picture for SA5P-R, the distributor's IQSA5PR-1, which is the same photograph as its IQSA5PL-1 for the left one: a LEFT folder, closed, from behind and right, with the bolt extension standing beside it; 1000 x 1000)","scaleRef":"196.7 px/in (.ext_pilot_length's note)","method":"145 px across","via":"harvest"}}]},"ext_groove_1":{"label":"The bolt extension: its body's first groove's centre behind the shoulder","kind":"length","measurements":[{"id":"photo","value":0.105,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-right-folder 0f82a51c8958 (Monadnock Firearms' picture for SA5P-R, the distributor's IQSA5PR-1, which is the same photograph as its IQSA5PL-1 for the left one: a LEFT folder, closed, from behind and right, with the bolt extension standing beside it; 1000 x 1000)","scaleRef":"196.7 px/in (.ext_pilot_length's note)","method":"row 400 (the silhouette narrows to 135 px)","via":"harvest"}}]},"ext_groove_2":{"label":"The bolt extension: its body's second groove's centre behind the shoulder","kind":"length","measurements":[{"id":"photo","value":0.314,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-right-folder 0f82a51c8958 (Monadnock Firearms' picture for SA5P-R, the distributor's IQSA5PR-1, which is the same photograph as its IQSA5PL-1 for the left one: a LEFT folder, closed, from behind and right, with the bolt extension standing beside it; 1000 x 1000)","scaleRef":"196.7 px/in (.ext_pilot_length's note)","method":"row 440","via":"harvest"}}]},"ext_groove_w":{"label":"The bolt extension: its body's grooves' width","kind":"length","measurements":[{"id":"photo","value":0.045,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-right-folder 0f82a51c8958 (Monadnock Firearms' picture for SA5P-R, the distributor's IQSA5PR-1, which is the same photograph as its IQSA5PL-1 for the left one: a LEFT folder, closed, from behind and right, with the bolt extension standing beside it; 1000 x 1000)","scaleRef":"196.7 px/in (.ext_pilot_length's note)","method":"the rows where the silhouette is under 140 px: 8 to 10","via":"harvest"}}]},"ext_groove_depth":{"label":"The bolt extension: its body's grooves' depth","kind":"length","measurements":[{"id":"photo","value":0.025,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-right-folder 0f82a51c8958 (Monadnock Firearms' picture for SA5P-R, the distributor's IQSA5PR-1, which is the same photograph as its IQSA5PL-1 for the left one: a LEFT folder, closed, from behind and right, with the bolt extension standing beside it; 1000 x 1000)","scaleRef":"196.7 px/in (.ext_pilot_length's note)","method":"(145 - 135) / 2 px","via":"harvest"}}]},"ext_neck_d":{"label":"The bolt extension: its neck's diameter","kind":"length","measurements":[{"id":"photo","value":0.488,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-right-folder 0f82a51c8958 (Monadnock Firearms' picture for SA5P-R, the distributor's IQSA5PR-1, which is the same photograph as its IQSA5PL-1 for the left one: a LEFT folder, closed, from behind and right, with the bolt extension standing beside it; 1000 x 1000)","scaleRef":"196.7 px/in (.ext_pilot_length's note)","method":"95 to 97 px across, rows 536 to 600","via":"harvest"}}]},"ext_neck_length":{"label":"The bolt extension: its neck, the body's rear step to where it flares","kind":"length","measurements":[{"id":"photo","value":0.513,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-right-folder 0f82a51c8958 (Monadnock Firearms' picture for SA5P-R, the distributor's IQSA5PR-1, which is the same photograph as its IQSA5PL-1 for the left one: a LEFT folder, closed, from behind and right, with the bolt extension standing beside it; 1000 x 1000)","scaleRef":"196.7 px/in (.ext_pilot_length's note)","method":"rows 522 to 620","via":"harvest"}}]},"ext_flare_length":{"label":"The bolt extension: its flare, neck to foot","kind":"length","measurements":[{"id":"photo","value":0.157,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-right-folder 0f82a51c8958 (Monadnock Firearms' picture for SA5P-R, the distributor's IQSA5PR-1, which is the same photograph as its IQSA5PL-1 for the left one: a LEFT folder, closed, from behind and right, with the bolt extension standing beside it; 1000 x 1000)","scaleRef":"196.7 px/in (.ext_pilot_length's note)","method":"rows 620 to 650","via":"harvest"}}]},"ext_foot_d":{"label":"The bolt extension: its foot's diameter (the end the buffer bears on)","kind":"length","measurements":[{"id":"photo","value":0.61,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/sylvan-arms-sa5-pro-right-folder 0f82a51c8958 (Monadnock Firearms' picture for SA5P-R, the distributor's IQSA5PR-1, which is the same photograph as its IQSA5PL-1 for the left one: a LEFT folder, closed, from behind and right, with the bolt extension standing beside it; 1000 x 1000)","scaleRef":"196.7 px/in (.ext_pilot_length's note)","method":"120 px across at rows 650 to 660","via":"harvest"}}]},"ext_weight":{"label":"The bolt extension's weight, worked out","kind":"mass","measurements":[{"id":"steel","value":2.82,"unit":"oz","pm":0.3,"source":{"type":"derived","expr":"{std.density.steel} * 0.785398 * ({.ext_pilot_d} * {.ext_pilot_d} * {.ext_pilot_length} + {.ext_body_d} * {.ext_body_d} * {.ext_body_length} + {.ext_neck_d} * {.ext_neck_d} * {.ext_neck_length} + ({.ext_neck_d} * {.ext_neck_d} + {.ext_neck_d} * {.ext_foot_d} + {.ext_foot_d} * {.ext_foot_d}) * {.ext_flare_length} / 3 + {.ext_foot_d} * {.ext_foot_d} * {.ext_foot_length})","via":"harvest"}}],"note":"No page weighs it apart. Worked out: its turned steel (\"1045 Steel\", the maker) at the ledger's sizes, the pilot, body, neck and foot as cylinders and the flare as a cone's frustum, the two grooves left in; the model's volume holds to it."},"ext_foot_length":{"label":"The bolt extension: its foot, the flare to its end face","kind":"length","measurements":[{"id":"rest","value":0.062,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.added_length} - {.ext_body_length} - {.ext_neck_length} - {.ext_flare_length}","via":"harvest"}}]}}},{"subject":"sylvan-arms-sa5-pro-right-folder","title":"Sylvan Arms SA5 Pro AR15 Folding Stock Adapter (Opens To The Right)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"maker","value":9.4,"unit":"oz","pm":0.05,"stated":"CNC-machined in the USA from 4140 Steel and only 9.4 ounces","source":{"type":"spec","publisher":"manufacturer","name":"Sylvan Arms, SA5 Pro AR15 Folding Stock Adapter (SKU SA5P; \"Direction of fold\": \"Adapter Opens To The Right\")","url":"https://sylvanarms.com/product/sa5-pro-ar15-folding-stock-adapter/","retrieved":"2026-10-18","via":"harvest"}},{"id":"ar15d","value":9.4,"unit":"oz","pm":0.05,"stated":"Weight 9.4 oz","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, Sylvan Arms AR-15 & AR-9 Folding Stock Adapter - Gen 5 - Right Folding - SA5P-R (MPN SA5P-R, UPC 811313033384; \"Additional information\")","url":"https://ar15discounts.com/products/sylvan-arms-ar-15-ar-9-folding-stock-adapter-gen-5-right-folding/","retrieved":"2026-10-18","via":"harvest"},"note":"The same field's \"Dimensions 8.85 × 6 × 2.5 in\" is a box: the part is not 8.85 in long."},{"id":"monadnock","value":9.4,"unit":"oz","pm":0.05,"stated":"CNC-machined in the USA from 4140 Steel and weighs only 9.4 ounces.","source":{"type":"spec","publisher":"retailer","name":"Monadnock Firearms, Sylvan Arms SA5 Pro AR-15 Folding Stock Adapter Gen. 5 Right Fold","url":"https://monadnockfirearms.com/product/sylvan-arms-sa5-pro-ar-15-folding-stock-adapter-gen-5-right-fold","retrieved":"2026-10-18","via":"harvest"}}],"adopt":{"from":"maker","reason":"The maker's own figure; both sellers of the right-folding one give the same."},"note":"The maker's figure for the adapter (one figure for both directions); no page says whether the bolt extension in the box is in it."},"added_length":{"label":"How far it moves the receiver extension back","kind":"length","measurements":[{"id":"maker","value":1.475,"unit":"in","pm":0.025,"stated":"It depends how the adapter times with the threads in your lower receiver, but it will be between 1.45 and 1.50 inches additional length.","source":{"type":"spec","publisher":"manufacturer","name":"Sylvan Arms, SA5 Pro AR15 Folding Stock Adapter, Q & A (\"How much extra length does this add?\", asked July 24, 2026, for the product with both directions; answered by the store manager the same day)","url":"https://sylvanarms.com/product/sa5-pro-ar15-folding-stock-adapter/","retrieved":"2026-10-18","via":"harvest"}}],"note":"The maker's answer for the product, either direction of fold."},"length":{"label":"Its length along the bore (its castle nut's front to the stock half's rear face)","kind":"length","measurements":[{"id":"added","value":1.475,"unit":"in","pm":0.025,"source":{"type":"derived","expr":"{.added_length}","via":"harvest"}}]},"hinge_x":{"label":"The hinge's axis behind the takedown pin","kind":"length","measurements":[{"id":"mirror","value":1.914,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{sylvan-arms-sa5-pro-left-folder.hinge_x}","via":"harvest"}}],"note":"The left-folding one's: no photo of this one is on file (the header)."},"hinge_z":{"label":"The hinge's axis out from the tube's axis, toward the side it folds to (the rifle's right)","kind":"length","measurements":[{"id":"mirror","value":1.232,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{sylvan-arms-sa5-pro-left-folder.hinge_z}","via":"harvest"}}],"note":"The left-folding one's, on the other side: the maker, \"Folding to the RIGHT folds toward the ejection port.\" No photo of this one is on file (the header)."},"fold_max":{"label":"How far the hinge turns before its own halves stop it","kind":"angle","measurements":[{"id":"mirror","value":180,"unit":"deg","pm":5,"source":{"type":"derived","expr":"{sylvan-arms-sa5-pro-left-folder.fold_max}","via":"harvest"}}],"note":"The left-folding one's (its photo opened flat)."},"width":{"label":"Its width across the rifle, the hinge included","kind":"length","measurements":[{"id":"mirror","value":2.222,"unit":"in","pm":0.08,"source":{"type":"derived","expr":"{sylvan-arms-sa5-pro-left-folder.width}","via":"harvest"}}]},"height":{"label":"Its height","kind":"length","measurements":[{"id":"mirror","value":2.158,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{sylvan-arms-sa5-pro-left-folder.height}","via":"harvest"}}]}}},{"subject":"taurus-tx22-barrel-46","title":"Taurus TX22 4.6 in threaded barrel","dimensions":{"stated_length":{"label":"Barrel length as its maker states it","kind":"length","measurements":[{"id":"shop","value":4.6,"unit":"in","pm":0.05,"stated":"Barrel Length: 4.6 inches","source":{"type":"spec","publisher":"manufacturer","name":"Taurus shop, Taurus TX22 T.O.R.O. Upper Assembly Kit (TX22TOROKIT), its specifications","url":"https://shoptaurus.com/new-items/taurustx-22-toro-conversion-kit","retrieved":"2026-11-05","via":"harvest"}},{"id":"sportsmans","value":4.6,"unit":"in","pm":0.05,"stated":"Barrel Length 4.6in","source":{"type":"spec","publisher":"retailer","name":"Sportsman's Warehouse, Taurus TX22 Gen 2 TORO 22 Long Rifle 4.6in Hard Anodized Black Pistol (MPN 1-2TX22P141)","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/handguns/taurus-tx22-gen-2-toro-22-long-rifle-46in-hard-anodized-black-pistol-221-rounds/p/1883977","retrieved":"2026-11-05","via":"harvest"}},{"id":"snw","value":4.6,"unit":"in","pm":0.005,"stated":"Barrel Length: 4.60 in. (threaded)","source":{"type":"spec","publisher":"review","name":"Shooting News Weekly, Gun Review: Taurus TX22 T.O.R.O. .22LR Pistol (its specifications list)","url":"https://www.shootingnewsweekly.com/gun-review/gun-review-taurus-tx22-t-o-r-o-22lr-pistol","retrieved":"2026-11-05","via":"harvest"}},{"id":"guntests","value":4.6,"unit":"in","pm":0.005,"stated":"BARREL LENGTH 4.60 In.","source":{"type":"spec","publisher":"review","name":"Gun Tests, Taurus TX22 T.O.R.O. Model Accepts Red Dots (its specifications table)","url":"https://www.gun-tests.com/?p=135657","retrieved":"2026-11-05","via":"harvest"}}],"adopt":{"from":"snw","reason":"All four print 4.6; Shooting News Weekly's and Gun Tests' print it to the hundredth (4.60), and the maker's shop's to the tenth."},"note":"Four pages print it, three of them for the whole T.O.R.O. (1-2TX22P141) and Taurus's own shop for this barrel in its conversion kit."},"thread_pitch":{"label":"The muzzle thread's pitch","kind":"length","measurements":[{"id":"shop","value":0.03571,"unit":"in","pm":0.00005,"stated":"Thread Pitch: 1/2x28","source":{"type":"spec","publisher":"manufacturer","name":"Taurus shop, Taurus TX22 T.O.R.O. Upper Assembly Kit (TX22TOROKIT), its specifications","url":"https://shoptaurus.com/new-items/taurustx-22-toro-conversion-kit","retrieved":"2026-11-05","via":"harvest"}},{"id":"sportsmans","value":0.03571,"unit":"in","pm":0.00005,"stated":"Thread Pitch 1/2 x 28","source":{"type":"spec","publisher":"retailer","name":"Sportsman's Warehouse, Taurus TX22 Gen 2 TORO 22 Long Rifle 4.6in Hard Anodized Black Pistol (MPN 1-2TX22P141)","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/handguns/taurus-tx22-gen-2-toro-22-long-rifle-46in-hard-anodized-black-pistol-221-rounds/p/1883977","retrieved":"2026-11-05","via":"harvest"}}],"adopt":{"from":"shop","reason":"The maker's own shop; the seller states the same thread."},"note":"28 threads to the inch: 1/2-28."},"thread_major_d":{"label":"The muzzle thread's major diameter (its crests)","kind":"length","measurements":[{"id":"tdp","value":0.4957,"unit":"in","pm":0.0033,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.thread_major_d}","via":"user"},"note":"A 1/2-28 thread's crests, for the 1/2x28 Taurus states: the Army barrel's 1/2-28 (8448549 sheet 1, Section M-M: \"1/2-28 UNEF-2A MAJOR DIA .4989/.4924\"), as read for BCM's barrel's ledger, where the drawing and its page are cited. Taurus names no class."}]},"thread_minor_d":{"label":"The muzzle thread's minor diameter (its roots)","kind":"length","measurements":[{"id":"tdp","value":0.4551,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{bcm-16-mid-barrel.thread_minor_d}","via":"user"},"note":"8448549 sheet 1, Section M-M: \"MINOR DIA .4551 MAX\", as read for BCM's barrel's ledger."}]},"shoulder_x":{"label":"The thread's shoulder, ahead of the breech face","kind":"length","measurements":[{"id":"slide-face","value":4.133,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{taurus-tx22-toro-slide.length} - {taurus-tx22-toro-slide.breech_x}","via":"harvest"},"note":"The slide's front face, from the barrel's breech face: where the protector's rear face goes out of sight in both side views."}],"note":"Where the protector's rear face bears: hidden in the photos at the slide's front face (the protector's silhouette runs at its full height right up to the slide's face in both side views, and a dark ring round it in the obliques is the face's own recess). Taken at the slide's front face."},"thread_length":{"label":"Threaded end, shoulder to muzzle face","kind":"length","measurements":[{"id":"derived","value":0.467,"unit":"in","pm":0.08,"source":{"type":"derived","expr":"{.stated_length} - {.shoulder_x}","via":"harvest"}}],"note":"On no page (the discovery's gap). Worked out: the maker's barrel length less where the shoulder stands."},"od":{"label":"The round barrel's outside diameter, through the slide's nose","kind":"length","measurements":[{"id":"assumed","value":0.55,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: a bull barrel between its thread's crests (0.496) and the thread protector's silhouette (0.59), whose rear face bears on its shoulder; the side vents show it filling their height (0.27 in) with its highlight under their top edge.","via":"harvest"}}],"note":"American Rifleman: \"The TX22 Black has a threaded bull barrel, which is the same barrel profile as the Competition model\". Its full silhouette shows in no photo on file: the nose hides it, and the vents show its middle only."},"block_top":{"label":"The chamber block's top above the bore axis","kind":"length","measurements":[{"id":"left","value":0.31,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/taurus-tx22-toro f0237849b397 (Sportsman's Warehouse 1883977-2: the T.O.R.O. from its left)","scaleRef":"the pin frame at the middle plane (158.8 px/in on the near face, 1.7% less on the middle plane)","method":"the silhouette's top at row 249.5 to 250 between x 500 and 690 (the slide's walls below it) against the protector's middle at row 298.5","via":"harvest"}},{"id":"right","value":0.308,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/taurus-tx22-toro e50c634c3e4d (Sportsman's Warehouse 1883977-1: the T.O.R.O. from its right)","scaleRef":"the pin frame (157.2 px/in), rolled 1.1 degrees","method":"the silhouette's top at row 259 to 262 between x 500 and 660 against the protector's middle carried back along the slide's lower edge (row 309 at x 580)","via":"harvest"}}],"adopt":{"from":"left","reason":"The two agree; the left view isn't rolled."},"note":"In the slide's open middle section the block stands above both walls: its top is the pistol's silhouette there in both black side views."},"block_front_x":{"label":"The chamber block's front end, ahead of the breech face","kind":"length","measurements":[{"id":"nose","value":1.467,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{taurus-tx22-toro-slide.nose_rear_x} - {taurus-tx22-toro-slide.breech_x}","via":"harvest"},"note":"The block's top silhouette runs from the slide's rear block to the nose's rear face in the left view; in the right-front oblique (7c0111a45816) its front step stands at the nose's rear face."}],"note":"Where the block steps down to the round barrel, just inside the slide's nose: the right-front oblique shows the step at the nose's rear face."},"block_width":{"label":"The chamber block's width across","kind":"length","measurements":[{"id":"assumed","value":0.58,"unit":"in","pm":0.08,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the block fills the slide's open channel between its walls in the right-front oblique (7c0111a45816), its right face (\"22 LR\") a little inside the port's rim.","via":"harvest"}}]},"block_bottom":{"label":"The chamber block's bottom below the bore axis","kind":"length","measurements":[{"id":"assumed","value":0.3,"unit":"in","pm":0.08,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the block's lower part is inside the frame and the slide (\"the barrel is stabilized against the frame\", American Rifleman); drawn down to the slide's lower edge.","via":"harvest"}}]},"bore_d":{"label":"The bore's diameter","kind":"length","measurements":[{"id":"nordic","value":0.218,"unit":"in","pm":0.006,"source":{"type":"derived","expr":"{nordic-22rb-upper.bore_d}","via":"harvest"},"note":"Another .22 LR barrel's bore, as read for the Nordic 22RB's ledger: no page gives this one's. The thread protector's front face shows a hole a little larger."}]},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"model","value":4.86,"unit":"oz","pm":0.8,"source":{"type":"derived","basis":"The model's steel, 1.0639 cubic inches (pipeline/blender/taurus_tx22_barrel_46.py's manifest), times std.density.steel (4.565 oz to the cubic inch; Gun Tests: \"BARREL MATERIAL Alloy Steel\"): 4.857 oz. The ± is mostly the round barrel's assumed diameter (0.55 ± 0.04: 15% of its section) and the block's assumed width and bottom. app/tests/taurus-tx22-barrel-46.test.ts holds the model's volume to it.","via":"harvest"}}],"note":"No page weighs the barrel alone (Taurus sells it only in the conversion kit, with the slide). Worked out from the model's steel (\"Barrel Material Alloy Steel\", Gun Tests)."}}},{"subject":"taurus-tx22-frame","title":"Taurus TX22 Gen 2 frame","dimensions":{"pistol_overall_length":{"label":"The pistol's overall length (the whole T.O.R.O., thread protector on)","kind":"length","measurements":[{"id":"sportsmans","value":7.6,"unit":"in","pm":0.05,"stated":"Overall Length 7.6","source":{"type":"spec","publisher":"retailer","name":"Sportsman's Warehouse, Taurus TX22 Gen 2 TORO 22 Long Rifle 4.6in Hard Anodized Black Pistol (MPN 1-2TX22P141)","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/handguns/taurus-tx22-gen-2-toro-22-long-rifle-46in-hard-anodized-black-pistol-221-rounds/p/1883977","retrieved":"2026-11-05","via":"harvest"}},{"id":"snw","value":7.6,"unit":"in","pm":0.005,"stated":"Overall length: 7.60 in.","source":{"type":"spec","publisher":"review","name":"Shooting News Weekly, Gun Review: Taurus TX22 T.O.R.O. .22LR Pistol (its specifications list)","url":"https://www.shootingnewsweekly.com/gun-review/gun-review-taurus-tx22-t-o-r-o-22lr-pistol","retrieved":"2026-11-05","via":"harvest"}},{"id":"rifleman","value":7.06,"unit":"in","pm":0.005,"stated":"Overall Length: 7.06\"","source":{"type":"spec","publisher":"review","name":"American Rifleman, Review: Taurus TX22 Black T.O.R.O. (its specifications box)","url":"https://www.americanrifleman.org/content/review-taurus-tx22-black-t-o-r-o/","retrieved":"2026-11-05","via":"harvest"}},{"id":"guntests","value":7.06,"unit":"in","pm":0.005,"stated":"OVERALL LENGTH 7.06 In.","source":{"type":"spec","publisher":"review","name":"Gun Tests, Taurus TX22 T.O.R.O. Model Accepts Red Dots (its specifications table)","url":"https://www.gun-tests.com/?p=135657","retrieved":"2026-11-05","via":"harvest"}}],"adopt":{"from":"snw","reason":"The photos decide (CLAUDE.md, a conflict is kept and adopted by what the part has to fit): framed by the two cross pins, the three side views give the frame's rear to the protector's face as 7.51 to 7.59 in at a pin spacing that also puts Blackstone's two rail slots 0.397 apart for the standard's 0.394; at 7.06 the same slots would stand 0.368 apart and the pins 1.26 in. 7.06 is the 4.1 in barrel's size in Taurus's manual as the discovery read it."},"note":"The pistol's figure, in the root part's ledger for every part to read. Two figures are published: 7.60 (Sportsman's, Shooting News Weekly; Taurus's own page as the discovery read it) and 7.06 (American Rifleman, Gun Tests). Taurus's manual, as the discovery read it (its PDF refusing the reader), lists two sizes, 7.6 and 7.1 in with 4.6 and 4.1 in barrels: 7.06 reads as the shorter one's."},"pistol_height":{"label":"The pistol's overall height","kind":"length","measurements":[{"id":"rifleman","value":5.44,"unit":"in","pm":0.005,"stated":"Height: 5.44\"","source":{"type":"spec","publisher":"review","name":"American Rifleman, Review: Taurus TX22 Black T.O.R.O. (its specifications box)","url":"https://www.americanrifleman.org/content/review-taurus-tx22-black-t-o-r-o/","retrieved":"2026-11-05","via":"harvest"}},{"id":"snw","value":5.44,"unit":"in","pm":0.005,"stated":"Overall Height: 5.44 In.","source":{"type":"spec","publisher":"review","name":"Shooting News Weekly, Gun Review: Taurus TX22 T.O.R.O. .22LR Pistol (its specifications list)","url":"https://www.shootingnewsweekly.com/gun-review/gun-review-taurus-tx22-t-o-r-o-22lr-pistol","retrieved":"2026-11-05","via":"harvest"}},{"id":"guntests","value":5.44,"unit":"in","pm":0.005,"stated":"OVERALL HEIGHT 5.44 In.","source":{"type":"spec","publisher":"review","name":"Gun Tests, Taurus TX22 T.O.R.O. Model Accepts Red Dots (its specifications table)","url":"https://www.gun-tests.com/?p=135657","retrieved":"2026-11-05","via":"harvest"}}],"adopt":{"from":"snw","reason":"Three reviews print the one figure (Taurus's own page, refusing the reader, the same by the discovery's reading); Shooting News Weekly's list is the one that also gives 7.60 and 17.30, the T.O.R.O.'s own figures."},"note":"To the top of the rear sight, from the bottom of the magazine in it: no page says which magazine. The side views read 5.47 to 5.56 in from the rear sight's top to the flush 16-round magazine's base pad (each taken a little from above, which adds to a height)."},"pistol_width":{"label":"The pistol's overall width, at its widest","kind":"length","measurements":[{"id":"rifleman","value":1.25,"unit":"in","pm":0.005,"stated":"Width: 1.25\"","source":{"type":"spec","publisher":"review","name":"American Rifleman, Review: Taurus TX22 Black T.O.R.O. (its specifications box)","url":"https://www.americanrifleman.org/content/review-taurus-tx22-black-t-o-r-o/","retrieved":"2026-11-05","via":"harvest"}},{"id":"snw","value":1.25,"unit":"in","pm":0.005,"stated":"Overall Width: 1.25 In.","source":{"type":"spec","publisher":"review","name":"Shooting News Weekly, Gun Review: Taurus TX22 T.O.R.O. .22LR Pistol (its specifications list)","url":"https://www.shootingnewsweekly.com/gun-review/gun-review-taurus-tx22-t-o-r-o-22lr-pistol","retrieved":"2026-11-05","via":"harvest"}},{"id":"guntests","value":1.25,"unit":"in","pm":0.005,"stated":"OVERALL WIDTH 1.25 In.","source":{"type":"spec","publisher":"review","name":"Gun Tests, Taurus TX22 T.O.R.O. Model Accepts Red Dots (its specifications table)","url":"https://www.gun-tests.com/?p=135657","retrieved":"2026-11-05","via":"harvest"}}],"adopt":{"from":"snw","reason":"Three reviews print the one figure; Shooting News Weekly's list is the T.O.R.O.'s (its 7.60 and 17.30)."},"note":"At its widest point, which the manual (as the discovery read it) says: \"1.25\" (at widest point)\". The ambidextrous safety's two levers are the widest thing on the frame in the oblique views."},"pistol_weight":{"label":"The pistol's weight, unloaded (without a magazine)","kind":"mass","measurements":[{"id":"sportsmans","value":17.3,"unit":"oz","pm":0.05,"stated":"Weight 17.3oz","source":{"type":"spec","publisher":"retailer","name":"Sportsman's Warehouse, Taurus TX22 Gen 2 TORO 22 Long Rifle 4.6in Hard Anodized Black Pistol (MPN 1-2TX22P141)","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/handguns/taurus-tx22-gen-2-toro-22-long-rifle-46in-hard-anodized-black-pistol-221-rounds/p/1883977","retrieved":"2026-11-05","via":"harvest"}},{"id":"snw","value":17.3,"unit":"oz","pm":0.005,"stated":"Overall Weight: 17.30 oz. (unloaded)","source":{"type":"spec","publisher":"review","name":"Shooting News Weekly, Gun Review: Taurus TX22 T.O.R.O. .22LR Pistol (its specifications list)","url":"https://www.shootingnewsweekly.com/gun-review/gun-review-taurus-tx22-t-o-r-o-22lr-pistol","retrieved":"2026-11-05","via":"harvest"}},{"id":"guntests","value":17.3,"unit":"oz","pm":0.005,"stated":"OVERALL WEIGHT 17.30 Oz. (Unloaded)","source":{"type":"spec","publisher":"review","name":"Gun Tests, Taurus TX22 T.O.R.O. Model Accepts Red Dots (its specifications table)","url":"https://www.gun-tests.com/?p=135657","retrieved":"2026-11-05","via":"harvest"}}],"adopt":{"from":"snw","reason":"All three say 17.3 oz unloaded; Shooting News Weekly's and Gun Tests' say it to the hundredth."}},"pistol_weight_with_magazine":{"label":"The pistol's weight with its 16-round magazine (empty)","kind":"mass","measurements":[{"id":"rifleman","value":19.7,"unit":"oz","pm":0.05,"stated":"Weight: 19.7 ozs. (with 16-round magazine)","source":{"type":"spec","publisher":"review","name":"American Rifleman, Review: Taurus TX22 Black T.O.R.O. (its specifications box)","url":"https://www.americanrifleman.org/content/review-taurus-tx22-black-t-o-r-o/","retrieved":"2026-11-05","via":"harvest"}}],"note":"American Rifleman's figure is the pistol with a magazine in it, not the unloaded figure: kept apart. Less pistol_weight it leaves 2.4 oz for the 16-round magazine, a check for that magazine's own weight."},"rail_length":{"label":"The accessory rail's length, under the dust cover","kind":"length","measurements":[{"id":"rifleman","value":1.75,"unit":"in","pm":0.005,"stated":"The dustcover features a molded-in 1.75\" accessory rail.","source":{"type":"spec","publisher":"review","name":"American Rifleman, Review: Taurus TX22 Black T.O.R.O. (its specifications box)","url":"https://www.americanrifleman.org/content/review-taurus-tx22-black-t-o-r-o/","retrieved":"2026-11-05","via":"harvest"}}]},"front_pin_x":{"label":"The front cross pin's centre ahead of the rear one (the origin), along the slide's travel","kind":"length","measurements":[{"id":"photos","value":1.355,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/taurus-tx22-toro 9efc84da32c0, f0237849b397, e50c634c3e4d (Blackstone's right side; Sportsman's left and right)","scaleRef":"the pistol's published overall length (7.60, pistol_overall_length) from the frame's rearmost point to the thread protector's front face: 2440, 1186 and 1179 px","method":"the pins' centres picked on 2.5x and 4x crops (the dark ring round each pin's end); their distance at each photo's overall-length scale: 1.354 (Blackstone), 1.365 (left), 1.351 (right). The ± covers the three and a pixel at each pin; Blackstone's rail (two slots 127.5 px apart at 321 px/in: 0.397 for the standard's 0.394) agrees.","via":"harvest"}}],"note":"The pin frame's scale. The two pins' ends show on both sides of the frame under the slide, the rear one behind the trigger at the origin. Every photo is framed by the two (trace.py method frame), so a part traced from any of them is in one frame."},"front_pin_y":{"label":"The front cross pin's centre above the rear one, square to the slide's travel","kind":"length","measurements":[{"id":"photos","value":0.03,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/taurus-tx22-toro 9efc84da32c0, f0237849b397, e50c634c3e4d","scaleRef":"front_pin_x","method":"the pins' line against a line fitted to the slide's lower edge along the frame (the lit edge of the frame's top in the two black views, the OD green's top edge in Blackstone's, over 5 to 7 in): 4.6 px over 214 (left), 4.6 over 212 (right), 10.2 over 433 (Blackstone): 0.029, 0.029, 0.032 in","via":"harvest"}}],"note":"The line through the two pins rises toward the muzzle against the slide's lower edge (the frame's top along its side, where the slide rides): the pin frame's x is along that edge, not along the pins."},"seam_y":{"label":"The frame's top along its side faces, where the closed slide's lower edge meets it, above the origin","kind":"length","measurements":[{"id":"photos","value":0.165,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/taurus-tx22-toro 9efc84da32c0, f0237849b397, e50c634c3e4d","scaleRef":"the pin frame (front_pin_x, front_pin_y)","method":"the slide's lower edge over the rear pin, on the frame's near face as the pin is (so a view from above moves both alike): 0.165 (Blackstone, the OD green's top), 0.162 (left), 0.171 (right)","via":"harvest"}}]},"bore_axis_y":{"label":"The bore axis's height above the frame's origin","kind":"length","measurements":[{"id":"photos","value":0.467,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/taurus-tx22-toro f0237849b397, e50c634c3e4d (Sportsman's left and right); 9efc84da32c0 (Blackstone) as a check","scaleRef":"the pin frame (front_pin_x, front_pin_y)","method":"the protector's silhouette's middle (its top and bottom edges over 45 to 70 columns: 92 and 93.5 px across) carried to the rear pin's column along the slide's lower edge: 0.460 (left) and 0.467 (right). Blackstone's reads 0.578: it is taken from about 11 degrees above (its cover plate's top and the trigger guard's top face show), and the pin, on the near face 0.48 in from the middle plane, stands about 0.09 lower in it than the bore's middle would at the same height: 0.49 less that. The ± covers the three and what the two black views' small elevation may add (the pins on the near face, the bore on the middle plane).","via":"harvest"}}],"note":"Onboarding checklist: Side view, scaled by the pistol's published sizes: the barrel's muzzle (its thread protector's) centre against the origin pin's. It is where the slide, the barrel and whatever is on the muzzle line up. Read on the thread protector's middle (the middle of its silhouette over its length, a turned part on the bore), carried back to the rear pin along the slide's lower edge."},"slide_rear_x":{"label":"Where a closed slide's rear face stands, from the origin","kind":"length","measurements":[{"id":"photos","value":-2.75,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/taurus-tx22-toro 9efc84da32c0, f0237849b397","scaleRef":"the pin frame (front_pin_x, front_pin_y)","method":"the silhouette's rearmost point on the rows 0.4 to 0.6 above the origin (the slide's rear face, behind nothing of the frame there), at the bore axis's height: -2.766 (Blackstone), -2.735 (left). Sportsman's right reads -2.668: it is yawed (its pins stand 0.05 to 0.07 forward of its outline against the other two), and is left out.","via":"harvest"}}],"note":"Onboarding checklist: Side view of the pistol closed: the slide's rear face against the origin pin. Each part's half of the seat: the frame states where, the slide has its origin there. The face leans (its top about 0.2 of its height ahead of its foot, 11 degrees): read at the bore axis's height."},"rear_x":{"label":"The frame's rearmost point, from the origin","kind":"length","measurements":[{"id":"photos","value":-2.894,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/taurus-tx22-toro 9efc84da32c0, f0237849b397","scaleRef":"the pin frame (front_pin_x, front_pin_y)","method":"the silhouette's rearmost point (the grip's back at 3.4 to 3.6 in under the origin): -2.894 (Blackstone, OD green), -2.914 (left); the tang over the web -2.85 (Blackstone at 0.2 under the origin)","via":"harvest"}}],"note":"Onboarding checklist: Side view: the tang behind the grip, the overall length's rear end. On the TX22 the rearmost point is the back of the grip low down (the swell 3.4 to 3.7 in under the origin), 0.05 in behind the tang over the web."},"grip_bottom_y":{"label":"The grip's bottom face, where a magazine's base pad bears","kind":"length","measurements":[{"id":"blackstone","value":-4.024,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/taurus-tx22-toro 9efc84da32c0 (Blackstone Shooting: a T.O.R.O. with an OD green frame from its right, the muzzle at the right, 2500 x 1844, alpha background)","scaleRef":"the pin frame (front_pin_x, front_pin_y): the rear pin at 962.0, 430.8 and the front at 1395.2, 425.2, 321.1 px/in","method":"the face's lowest stretch over the pad's span (-4.046 from x -2.46 to -2.19, the OD green's lower edge at the half level of its fall to the pad's black: rows 1712 to 1717) carried to magwell_x at the pad's rise of 1.0 degree: -4.046 + 1.25 x tan(1.0) = -4.024 (the pad's rear end at -2.39, its nose at pad_nose_x less its length). The ± covers the rise's own (0.9 degree over 1.25 in) and a pixel and a half.","via":"harvest"}}],"note":"Onboarding checklist: Side view: the grip's lower edge at the magazine's front, against the origin pin. The grip's bottom face (profiles.side, the OD green's lower edge over the black pad) runs nearly level over the pad, lowest at its rear (grip_bottom_low, x -2.46 to -2.19), rising about a degree and a half to x -1.2 and then rounding up into the front strap (-3.98 at x -0.97, -3.93 at -0.86). The pad's top bears on the face's lowest stretch and stands under its front round, as Blackstone's picture has it (a dark gap over the pad's nose): this is that face's line at magwell_x, the lowest stretch carried forward at the pad's own rise (taurus-tx22-magazine-16.pad_top_rise, 1.0 degree). Until 2026-11-05 21:47 it was the round's own height there (-3.98), which stood a magazine's pad 0.04 in up into the frame at its rear."},"grip_bottom_low":{"label":"The grip's bottom face at its lowest over a magazine's pad (its rear stretch, ahead of the heel)","kind":"length","measurements":[{"id":"blackstone","value":-4.046,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/taurus-tx22-toro 9efc84da32c0 (Blackstone Shooting: a T.O.R.O. with an OD green frame from its right, the muzzle at the right, 2500 x 1844, alpha background)","scaleRef":"the pin frame (front_pin_x, front_pin_y): the rear pin at 962.0, 430.8 and the front at 1395.2, 425.2, 321.1 px/in","method":"profiles.side's lower edge from x -2.46 to -2.19 (the stretch between the heel's front face and the face's step up at -2.14)","via":"harvest"}}]},"magwell_x":{"label":"The front of a seated magazine's body at the grip's bottom","kind":"length","measurements":[{"id":"derived","value":-1.144,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.pad_nose_x} - {taurus-tx22-magazine-16.pad_front_ahead}","via":"harvest"},"note":"The nose at -0.76 less its 0.384 ahead of the body: the front wall is then 0.20 thick 3.6 in under the origin and the pad's rear end 0.07 ahead of the heel's front face, where the photo has it (-2.47)."}],"note":"Onboarding checklist. The magazine's body is inside the grip: what shows is the base pad's nose ahead of it (pad_nose_x), and the magazine's owner reads how far the nose stands ahead of the body's front on photos of the magazine alone (taurus-tx22-magazine-16.pad_front_ahead). Until 2026-11-05 22:15 an assumption (-0.97: the front strap's foot less a 0.12 wall), which left the well's front wall 0.03 thick 3.6 in under the origin and broke through the front strap's round at its corners (a white triangle beside the pad in the front-quarter render), and stood the pad's nose 0.17 ahead of where Blackstone's photo has it."},"pad_nose_x":{"label":"A seated magazine's base pad: its nose at the pad's top, ahead of the origin","kind":"length","measurements":[{"id":"blackstone","value":-0.76,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/taurus-tx22-toro 9efc84da32c0 (Blackstone Shooting: a T.O.R.O. with an OD green frame from its right, the muzzle at the right, 2500 x 1844, alpha background)","scaleRef":"the pin frame (front_pin_x, front_pin_y): the rear pin at 962.0, 430.8 and the front at 1395.2, 425.2, 321.1 px/in","method":"the black pad's front edge under the grip's front round (the flush 16-round in the photo), at the pad's top: -0.76; at its foot -0.74","via":"harvest"}}]},"magwell_rake":{"label":"The magazine well's lean: its front wall from upright, top toward the muzzle","kind":"angle","measurements":[{"id":"blackstone","value":14.5,"unit":"deg","pm":1.5,"source":{"type":"photo","photo":"references/taurus-tx22-toro 9efc84da32c0 (Blackstone Shooting: a T.O.R.O. with an OD green frame from its right, the muzzle at the right, 2500 x 1844, alpha background)","scaleRef":"the pin frame (front_pin_x, front_pin_y): the rear pin at 962.0, 430.8 and the front at 1395.2, 425.2, 321.1 px/in","method":"the OD green's front edge between 2.0 and 3.6 in under the origin (-0.435 at -2.0, -0.541 at -2.4, -0.852 at -3.6): 14.6 and 14.5 degrees over the two stretches","via":"harvest"}}],"note":"The magazine goes in along the grip: the front strap's outer face is the reading (its inner wall taken to be parallel)."},"grip_x":{"label":"The grip's middle along the pistol, at grip_y (where the firing hand holds it)","kind":"length","measurements":[{"id":"blackstone","value":-1.75,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/taurus-tx22-toro 9efc84da32c0 (Blackstone Shooting: a T.O.R.O. with an OD green frame from its right, the muzzle at the right, 2500 x 1844, alpha background)","scaleRef":"the pin frame (front_pin_x, front_pin_y): the rear pin at 962.0, 430.8 and the front at 1395.2, 425.2, 321.1 px/in","method":"midway between the grip's front strap (-0.66) and back strap (-2.85) at grip_y","via":"harvest"}}]},"grip_y":{"label":"The grip's middle height (where the firing hand holds it)","kind":"length","measurements":[{"id":"blackstone","value":-2.85,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/taurus-tx22-toro 9efc84da32c0 (Blackstone Shooting: a T.O.R.O. with an OD green frame from its right, the muzzle at the right, 2500 x 1844, alpha background)","scaleRef":"the pin frame (front_pin_x, front_pin_y): the rear pin at 962.0, 430.8 and the front at 1395.2, 425.2, 321.1 px/in","method":"midway between the frame's underside behind the trigger guard, where the front strap begins (-1.7), and the grip's bottom face (-4.0)","via":"harvest"}}]},"rail_slots":{"label":"How many slots the rail under the dust cover has","kind":"count","measurements":[{"id":"photos","value":2,"unit":"count","source":{"type":"photo","photo":"references/taurus-tx22-toro 9efc84da32c0 (Blackstone Shooting: a T.O.R.O. with an OD green frame from its right, the muzzle at the right, 2500 x 1844, alpha background); Sportsman's f0237849b397, e50c634c3e4d, d4f6e257c86f, 7c0111a45816","scaleRef":"none needed","method":"the gaps in the rail's lower edge, counted: two in every side view and in both obliques from the front","via":"harvest"}}]},"rail_slot0_x":{"label":"The rail's rear slot's centre, ahead of the origin","kind":"length","measurements":[{"id":"blackstone","value":3.489,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/taurus-tx22-toro 9efc84da32c0 (Blackstone Shooting: a T.O.R.O. with an OD green frame from its right, the muzzle at the right, 2500 x 1844, alpha background)","scaleRef":"the pin frame (front_pin_x, front_pin_y): the rear pin at 962.0, 430.8 and the front at 1395.2, 425.2, 321.1 px/in","method":"the rear slot's two walls where the silhouette's alpha crosses a half, on three rows just above the rail's face: 2042.9 and 2108.3 px (65.4 px, 0.204 in for the standard's 0.206); the middle at x 3.489 (.cache/tx22/taurus-tx22-frame/rail.py). The front slot's front wall shows a lit face (the slot seen a little from ahead), so it is placed by its rear wall: 3.885 for the pitch's 3.883.","via":"harvest"}}],"note":"The second slot is a pitch (std.picatinny.slot_pitch) ahead: Blackstone's two rear edges are 127.3 px apart, 0.3965 in for the standard's 0.394."},"rail_top_y":{"label":"The rail's mounting face (its top, turned down under the dust cover), above the origin","kind":"length","measurements":[{"id":"left","value":-0.566,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/taurus-tx22-toro f0237849b397 (Sportsman's Warehouse 1883977-2: the black T.O.R.O. from its left, 1200 x 1200)","scaleRef":"the pin frame (front_pin_x, front_pin_y): the rear pin at 735.0, 372.0 and the front at 520.8, 367.0, 158.8 px/in","method":"profiles.left's lower edge on the rail's teeth between the slots (x 2.8 to 3.2: -0.567, -0.565), grey under 150","via":"harvest"}},{"id":"blackstone","value":-0.561,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/taurus-tx22-toro 9efc84da32c0 (Blackstone Shooting: the OD green T.O.R.O. from its right, 2500 x 1844)","scaleRef":"the pin frame: the rear pin at 962.0, 430.8 and the front at 1395.2, 425.2, 321.1 px/in","method":"the silhouette's lower edge (alpha a half) on the teeth, -0.535 between the slots, less what the view's height above the pistol lifts an edge 0.137 in nearer the middle than the pins (the rail head's lower corner at 0.328 off the middle, the pins at 0.465): 0.026, at the 11 degrees the bore's reading gives (13 by this edge and the left view's)","via":"harvest"}}],"adopt":{"from":"left","reason":"The left view is nearly level (no screw head of the cover plate is seen from above); Blackstone's needs a correction for its height, which brings it within 0.005."},"note":"Blackstone's view, taken from above, has the rail's face 0.03 in higher than the near-level left view: its lower corner stands 0.14 in nearer the middle plane than the pins it is framed by, and a view from 13 degrees above lifts it that much. The left view's reading is adopted, the other corrected for it beside it."},"rail_front_x":{"label":"The rail's front end (the front tooth's front face), ahead of the origin","kind":"length","measurements":[{"id":"blackstone","value":4.068,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/taurus-tx22-toro 9efc84da32c0 (Blackstone Shooting: a T.O.R.O. with an OD green frame from its right, the muzzle at the right, 2500 x 1844, alpha background)","scaleRef":"the pin frame (front_pin_x, front_pin_y): the rear pin at 962.0, 430.8 and the front at 1395.2, 425.2, 321.1 px/in","method":"where the silhouette's lower edge leaves the front tooth (column 2262); the dust cover's front face then rises at a slant to the slide's front (column 2286)","via":"harvest"}}]},"safety_proud":{"label":"How far each lever of the manual safety stands out from the frame's side face","kind":"length","measurements":[{"id":"derived","value":0.16,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"({.pistol_width} - {.body_width}) / 2","via":"harvest"}}],"note":"The published widest point (pistol_width) is taken to be across the safety's two levers: they are the widest thing on the frame in both obliques from the front."},"body_width":{"label":"The frame's width across its side faces under the slide (the dust cover, over the trigger, the tang)","kind":"length","measurements":[{"id":"slide","value":0.93,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{taurus-tx22-toro-slide.width}","via":"harvest"}}],"note":"No view on file is square across the frame. In both obliques from the front (7c0111a45816 along the seam over the trigger and at the rear, d4f6e257c86f at the rear under the safety's lever) the slide's side runs down into the frame's with no ledge between them: the frame is taken as wide as the slide there, which its owner reads in the right oblique against the thread protector's front face (taurus-tx22-toro-slide.width)."},"grip_width":{"label":"The grip's width across its sides at its widest (its foot and up its panels)","kind":"length","measurements":[{"id":"sleeve","value":1.115,"unit":"in","pm":0.025,"source":{"type":"derived","expr":"{taurus-tx22-magazine-22.sleeve_width}","via":"harvest"},"note":"Flush with the grip's foot in Taurus's picture of the 22-round seated."},{"id":"pad","value":1.186,"unit":"in","pm":0.029,"source":{"type":"derived","expr":"{taurus-tx22-magazine-16.pad_width}","via":"harvest"},"note":"A hair proud of the grip's sides in Handguns' view from below."}],"adopt":{"from":"sleeve","reason":"Taurus's own picture, made to show the fit, has the sleeve's side face flush with the grip's foot; Handguns' has the pad a little proud of it."},"note":"No view on file is square across the frame. The magazine's base is flush with the grip's sides seated: Taurus's own picture of the 22-round in a TX22 (taurus-tx22-magazine-22 c3fd2bc09052, \"to display proper magazine fit\") has the sleeve's side face run on from the grip's foot, and Handguns' view of the 16-round's pad from below (taurus-tx22-magazine-16 9e7b75ff19e1) the pad's sides with the grip's, a hair proud. The grip is taken as wide as the sleeve, the magazines' owner's reading of Taurus's end view, the pad's kept beside it. Until 2026-11-05 22:25 an assumption of the slide's width (0.93), which left the pad standing out of each side by 0.13. Above the panels the frame narrows to body_width (the model eases between y -0.95 and -0.45)."},"guard_width":{"label":"The trigger guard's bars' width across","kind":"length","measurements":[{"id":"assumed","value":0.4,"unit":"in","pm":0.08,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the guard's bars are seen only from their sides and, from above, their top faces in Blackstone's view (taken from about 11 degrees above), where the lower bar's top face shows 0.03 to 0.04 in of its depth."}}]},"trigger_width":{"label":"The trigger shoe's width across","kind":"length","measurements":[{"id":"assumed","value":0.3,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the trigger is seen only from its sides; in the obliques its face is turned away."}}]},"strap_round":{"label":"The radius the grip's front and back straps are rounded to, across the grip","kind":"length","measurements":[{"id":"assumed","value":0.3,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: in both obliques the front strap reads as a broad round from one side to the other with no flat face of its own, and the back strap rounds into the sides behind the panels; no view looks along either."}}]},"edge_round":{"label":"The radius the frame's corners are rounded to elsewhere (the dust cover's front corners, the tang's)","kind":"length","measurements":[{"id":"assumed","value":0.06,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the dust cover's front corners and the tang's read rounded and small in the close views from the front (e546d93843c1) and of the rear (b2ff2ae9a5cd)."}}]},"dust_cover_bottom_y":{"label":"The dust cover's underside beside the rail's head, above the origin","kind":"length","measurements":[{"id":"blackstone","value":-0.381,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/taurus-tx22-toro 9efc84da32c0 (Blackstone Shooting: a T.O.R.O. with an OD green frame from its right, the muzzle at the right, 2500 x 1844, alpha background)","scaleRef":"the pin frame (front_pin_x, front_pin_y): the rear pin at 962.0, 430.8 and the front at 1395.2, 425.2, 321.1 px/in","method":"the line along the dust cover's side over the rail's teeth, where the side face's lower edge meets the rail's head (row 550, x 3.3 to 4.0): -0.373, less what the view's height lifts an edge on the stepped-in band's face, 0.04 nearer the middle than the pins (0.008)","via":"harvest"}}],"note":"The rail's head hangs under it (std.picatinny.lower_gauge_below_top above the rail's face is 0.154: -0.381), narrower than the dust cover."},"controls_proud":{"label":"How far the disassembly latch's ends, the magazine release's buttons and the slide stop stand out from the frame's side faces","kind":"length","measurements":[{"id":"assumed","value":0.05,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: each shows from its side only; in the obliques they stand a little proud of the frame's side, less than the safety's levers."}}]},"pin_end_d":{"label":"The cross pins' bright ends' diameter, on the frame's side faces","kind":"length","measurements":[{"id":"blackstone","value":0.065,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/taurus-tx22-toro 9efc84da32c0 (Blackstone Shooting: a T.O.R.O. with an OD green frame from its right, the muzzle at the right, 2500 x 1844, alpha background)","scaleRef":"the pin frame (front_pin_x, front_pin_y): the rear pin at 962.0, 430.8 and the front at 1395.2, 425.2, 321.1 px/in","method":"the bright end inside each pin's dark ring on a 2.5x crop: about 20 px across (the ring round it about 30 px, 0.094 in)","via":"harvest"}}]},"magwell_across":{"label":"The magazine well's width across the grip","kind":"length","measurements":[{"id":"magazine","value":0.64,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{taurus-tx22-magazine-16.body_width}","via":"harvest"},"note":"No view looks into the well: it is cut to the magazine's own body (its width read by the magazine's owner on Taurus's end view of the 22-round, whose body the 16-round's is), with the model's clearance round it. Until 2026-11-05 21:47 an assumption of 0.62."}]},"panel_recess":{"label":"How far the grip's stippled panels lie below the smooth borders round them","kind":"length","measurements":[{"id":"assumed","value":0.012,"unit":"in","pm":0.008,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the borders round the panels read raised in the close view of the grip (0c6d81d099f9) and in Blackstone's side view, by an amount no view gives; sunk this much the panels' edge shows at the size the page draws a pistol."}}]},"finger_index_depth":{"label":"How deep the indentations over the trigger guard are sunk into the frame's sides","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: their outline shows in Blackstone's side view by its shadowed edge, their depth in no view."}}]},"cover_band_depth":{"label":"How far the dust cover's lower band is stepped in along each side","kind":"length","measurements":[{"id":"assumed","value":0.04,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the step shows in Blackstone's side view as a shadowed line and in the close view from the front (e546d93843c1) as a ledge, its depth in neither."}}]},"guard_bar_top_y":{"label":"The trigger guard's lower bar's top (the opening's floor), above the origin","kind":"length","measurements":[{"id":"left","value":-1.595,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/taurus-tx22-toro f0237849b397 (Sportsman's Warehouse 1883977-2: the black T.O.R.O. from its left, 1200 x 1200)","scaleRef":"the pin frame (front_pin_x, front_pin_y), 158.8 px/in","method":"where a line down the frame at x 0.7, 1.0, 1.3 and 1.6 goes from the background into the bar (grey under 150): -1.598, -1.598, -1.592, -1.592","via":"harvest"}},{"id":"right","value":-1.617,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/taurus-tx22-toro e50c634c3e4d (Sportsman's Warehouse 1883977-1: the black T.O.R.O. from its right, 1200 x 1200)","scaleRef":"the pin frame: the rear pin at 452.5, 382.5 and the front at 664.5, 374.5, 157.2 px/in","method":"the same lines: -1.620, -1.612, -1.616, -1.622","via":"harvest"}}],"adopt":{"from":"left","reason":"The left view's frame agrees with Blackstone's at the pins and the grip's foot (0.02 in) where the right view is yawed; the right is kept as the check, 0.022 apart."},"note":"Blackstone's view, from above, sees the bar's top face and has its far edge for the opening's floor, 0.13 in higher (-1.468); the two black views, nearly level, have the bar's edge. The model moves its outline's floor here."},"guard_bar_bottom_y":{"label":"The trigger guard's lower bar's bottom, above the origin","kind":"length","measurements":[{"id":"left","value":-1.771,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/taurus-tx22-toro f0237849b397 (Sportsman's Warehouse 1883977-2: the black T.O.R.O. from its left, 1200 x 1200)","scaleRef":"the pin frame (front_pin_x, front_pin_y), 158.8 px/in","method":"where the same lines leave the bar into the background: -1.774, -1.774, -1.768, -1.768","via":"harvest"}},{"id":"right","value":-1.791,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/taurus-tx22-toro e50c634c3e4d (Sportsman's Warehouse 1883977-1: the black T.O.R.O. from its right, 1200 x 1200)","scaleRef":"the pin frame, 157.2 px/in","method":"the same lines: -1.792, -1.790, -1.790, -1.794","via":"harvest"}}],"adopt":{"from":"left","reason":"As guard_bar_top_y: the right view kept as the check, 0.02 apart."},"note":"Blackstone's outline has it at -1.70: the bar's near lower edge stands 0.27 in nearer the middle than the pins it is framed by, and the view's height lifts it. The model moves its outline's bar here."},"trigger_drop":{"label":"How much lower the trigger stands than Blackstone's view draws it","kind":"length","measurements":[{"id":"left","value":-0.07,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/taurus-tx22-toro f0237849b397 (Sportsman's Warehouse 1883977-2: the black T.O.R.O. from its left, 1200 x 1200)","scaleRef":"the pin frame, 158.8 px/in","method":"the trigger's tip, its lowest dark pixel ahead of the guard's floor (about x 0.98, y -1.40), against Blackstone's (x 1.085, y -1.33); the pin's bright end through the trigger likewise (-0.770 left, -0.702 Blackstone). Their x differs by 0.1 at the tip and 0.02 at the pin: the tip isn't moved along","via":"harvest"}}],"note":"The trigger's sides are 0.15 in off the middle, 0.31 nearer it than the pins Blackstone's view is framed by, and the view's height lifts them: its tip reads -1.33 there and -1.40 in the left view. The model takes Blackstone's outline of the trigger (the only one told from the frame by its colour) this much lower."},"trigger_pin_x":{"label":"The trigger's pin, its bright end on the trigger's side, ahead of the origin","kind":"length","measurements":[{"id":"left","value":0.499,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/taurus-tx22-toro f0237849b397 (Sportsman's Warehouse 1883977-2: the black T.O.R.O. from its left, 1200 x 1200)","scaleRef":"the pin frame (front_pin_x, front_pin_y), 158.8 px/in","method":"the bright end's middle on a 12x crop (655.8, 494.2); Blackstone's has it at 0.515 (1126.5, 656.9 on an 8x crop)","via":"harvest"}}]},"trigger_pin_y":{"label":"The trigger's pin above the origin","kind":"length","measurements":[{"id":"left","value":-0.77,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/taurus-tx22-toro f0237849b397 (Sportsman's Warehouse 1883977-2: the black T.O.R.O. from its left, 1200 x 1200)","scaleRef":"the pin frame (front_pin_x, front_pin_y), 158.8 px/in","method":"as trigger_pin_x; Blackstone's reads -0.702, lifted by its height as the trigger is (trigger_drop)","via":"harvest"}}]},"trigger_pin_d":{"label":"The trigger's pin's bright end, across","kind":"length","measurements":[{"id":"blackstone","value":0.11,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/taurus-tx22-toro 9efc84da32c0 (Blackstone Shooting: the OD green T.O.R.O. from its right, 2500 x 1844)","scaleRef":"the pin frame, 321.1 px/in","method":"the bright disc with its rim on an 8x crop, 36 px across (the left view's 0.08 to 0.115 by its dark ring)","via":"harvest"}}]},"width":{"label":"Width across the frame's grip","kind":"length","measurements":[{"id":"derived","value":1.115,"unit":"in","pm":0.025,"source":{"type":"derived","expr":"{.grip_width}","via":"harvest"}}],"note":"Onboarding checklist: A view from the front or the rear, or a camera fitted to an oblique; the published overall width is at the widest point (its controls). No such view is on file: grip_width's assumption."},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"pistol-less-parts","value":6.37,"unit":"oz","pm":1,"source":{"type":"derived","expr":"{.pistol_weight} - {taurus-tx22-toro-slide.weight} - {taurus-tx22-barrel-46.weight} - {taurus-tx22-thread-protector.weight} - {taurus-tx22-magazine-16.weight}","via":"harvest"},"note":"The published 17.3 oz, which is with its 16-round magazine in it (Handguns: \"the total weight of the pistol is just 17.3 ounces, and that's with an unloaded magazine inserted\"), less the slide (4.57), the barrel (4.86), the protector (0.23) and the magazine (1.31), each weighed by its own metal in its ledger (2026-11-05; the magazine taken out at the orchestrator's integration, when the assembled pistol weighed 18.6 oz): worked out, not weighed. The model's polymer alone (7.86 cubic inches of std.density.polymer: 5.2 oz) is under it, the steel of the trigger group, the safety, the latches and their springs the rest."}],"note":"Onboarding checklist: Where only the pistol's is published, the frame's is that less the others' (each a derived entry), said as worked out. The frame as sold carries its trigger group, the magazine release, the safety, the disassembly latch and their springs and pins, steel most of them: its polymer alone (the model's volume as std.density.polymer) is the floor."}}},{"subject":"taurus-tx22-magazine-16","title":"Taurus TX22 .22 LR 16-Round Magazine","dimensions":{"overall_height":{"label":"Overall height, feed lips to base","kind":"length","measurements":[{"id":"square","value":4.683,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/taurus-tx22-magazine-22 c468e0cbc9ec (Gun Mag Warehouse, the 22-round from its right, square on: the body over its sleeve) and references/taurus-tx22-toro 9efc84da32c0 (Blackstone: the pad seated)","scaleRef":"profiles.body (scaled by body_front_to_back, 1.185 in) and profiles.pad (the frame's rail pitch)","method":"the body's top over the pad's top at the body's front on the square view, 4.395 (profiles.body's highest point less the 0.037 its front foot stands over its rear), and the pad's bottom under it as seated, 0.287 (the model's script: profiles.pad put in the part's frame); the model's height (its manifest's bounds)","via":"harvest"}},{"id":"photo","value":4.738,"unit":"in","pm":0.117,"source":{"type":"photo","photo":"references/taurus-tx22-magazine-22 fb7549e66665 (Gun Mag Warehouse, the 16-round from its right (2000 x 2000), standing on its pad, the front at the right)","scaleRef":"scale from taurus-tx22-magazine-16.base_pad_length = 1.630 in, its adopted reading (median width over 0.94–0.985 of the height from the top, 618 px → 379.1 px/in)","method":"height of the traced outline (tools/trace.py); pad's bottom to the body's top (its highest point, the follower's lip at the front); read from a little above, so the top is the far edge of the top face","via":"harvest"}}],"adopt":{"from":"square","reason":"The square view's body: the other is read from a little above, its top the top face's far edge (some 0.07 in higher at 9 degrees), and the two agree within its ±."},"note":"As the magazine stands in the grip (its pad level), the pad's bottom to the body's highest point."},"below_grip":{"label":"How far its base pad stands below the grip, seated","kind":"length","measurements":[{"id":"seated","value":0.272,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/taurus-tx22-toro 9efc84da32c0 (Blackstone Shooting's T.O.R.O. with an OD green frame from its right (2500 x 1844), square on: the 16-round's black pad under the grip)","scaleRef":"frame from the reviewed holes slot_rear, slot_front (324.2 px/in, rms 0.000 in over 2 points)","method":"height in x [-5.45, -4.95] of the traced outline (tools/trace.py); how far the pad stands below the grip's bottom edge at the middle of its length, where its bottom is straight","via":"harvest"}}],"note":"Onboarding checklist."},"weight":{"label":"Weight, empty","kind":"mass","measurements":[{"id":"model","value":1.314,"unit":"oz","pm":0.6,"source":{"type":"derived","basis":"The model's polymer volume, 1.9945 cubic inches (its manifest's volume_in3: the body 1.500, the pad 0.470, the buttons 0.025), times std.density.polymer (Zytel nylon 66, 18.68 g, 0.6589 oz to the cubic inch): 1.314 oz. Taurus says only \"high-density polymer\": a glass-filled grade is up to a sixth heavier; the inside's size is assumed (a staggered column of rounds' room: ± 0.08 in across moves 0.2 oz); the steel spring and the follower's own shape aren't in it. The ± takes them.","via":"harvest"}}],"adopt":{"from":"model","reason":"The model's own polymer, its inside assumed: the sellers' figures are shipping weights (`shipping_weight`; Shiner's 0.15 lb, the lightest, is called one by its page: 2.4 oz, 1.1 over this, which the spring, a box or a bag would be). American Rifleman's 19.7 oz for the pistol \"with 16-round magazine\" less Taurus's 17.3 oz is 2.4 oz too, but Handguns says its 17.3 oz was \"with an unloaded magazine inserted\": no difference of the two is the magazine's."},"note":"No page weighs the magazine itself: three sellers give a weight in their shipping fields (`shipping_weight`, beside this). The model's polymer is the figure used (its id `model`, written when the model is built)."},"shipping_weight":{"label":"Weight as shipped (sellers' shipping fields)","kind":"mass","measurements":[{"id":"shiner","value":0.15,"unit":"lb","stated":"it features an 8.5-inch length and 0.15-pound shipping weight","source":{"type":"spec","publisher":"retailer","name":"Shiner Tactical, Taurus TX22 Magazine .22LR 16RD Black Steel","url":"https://shinertactical.com/product/taurus-tx22-magazine-22lr-16rd-black-steel/","retrieved":"2026-11-05","via":"harvest"},"note":"A shipping weight, in the seller's own words; the 8.5 in beside it is the carton's (the magazine is some 5 in tall)."},{"id":"galati","value":0.5,"unit":"lb","pm":0.005,"stated":"Weight: 0.50 pounds","source":{"type":"spec","publisher":"retailer","name":"Galati International, Taurus TX22 .22 LR 16 Round Factory Steel Magazine - Black (TR358001701)","url":"https://www.galatiinternational.com/taurus-tx22-22-lr-16-round-magazine-black.html","retrieved":"2026-11-05","via":"harvest"},"note":"A shop's shipping field: half a pound for a polymer magazine."},{"id":"kygunco","value":2,"unit":"lb","stated":"Weight 2 lb","source":{"type":"spec","publisher":"retailer","name":"KYGUNCO, Taurus 358-0017-01 TX22 22LR 16rd Poly Black Magazine (item 140003)","url":"https://www.kygunco.com/product/taurus-358-0017-01-tx22-22lr-16rd-poly-black-magazine","retrieved":"2026-11-05","via":"harvest"},"note":"The shop's shipping class: the same 2 lb is on its 22-round's page."}],"adopt":{"from":"shiner","reason":"The lightest of the shipping fields, adopted only so the entry resolves: none of them is the magazine's weight."},"note":"What sellers give in their shipping fields, kept beside the magazine's weight and not in it (D104: a shipping class of 2 lb under `weight` widened the pistol's weight to 60 oz by its sources). Not used for anything; with more than one figure the lightest is adopted only so the entry resolves."},"capacity":{"label":"Capacity","kind":"count","measurements":[{"id":"taurus","value":16,"unit":"count","stated":"Taurus TX22 .22 LR 16-Round Magazine - Black (358-0017-01-WB)","source":{"type":"spec","publisher":"manufacturer","name":"Taurus (shoptaurus.com), Taurus TX22 .22 LR 16-Round Magazine - Black","url":"https://shoptaurus.com/tx22-22lr-22rd-magazine-assembly-web","retrieved":"2026-11-05","via":"harvest"}},{"id":"primary-arms","value":16,"unit":"count","stated":"Taurus TX22 22lr Magazine - 16 Round","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Taurus TX22 22lr Magazine - 16 Round (SKU 358-0017-01)","url":"https://www.primaryarms.com/taurus-tx22lr-magazine-16-round","retrieved":"2026-11-05","via":"harvest"}}],"adopt":{"from":"taurus","reason":"The maker's own shop; the seller says the same."}},"base_pad_length":{"label":"The pad's length, nose to rear end","kind":"length","measurements":[{"id":"seated","value":1.763,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/taurus-tx22-toro 9efc84da32c0 (Blackstone Shooting's T.O.R.O. with an OD green frame from its right (2500 x 1844), square on: the 16-round's black pad under the grip)","scaleRef":"frame from the reviewed holes slot_rear, slot_front (324.2 px/in, rms 0.000 in over 2 points)","method":"width of the traced outline (tools/trace.py); the pad's length, front tip to rear end, as it shows under the grip (Blackstone's right side, scaled by the frame's rail: one slot pitch, 127.75 px, ± 1 px)","via":"harvest"}},{"id":"release","value":1.63,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"What the pad's length would be if the magazine's catch notch (profiles.body's catch_notch, its middle 3.129 in over the seat at the seated reading's scale) stood at the middle of the frame's magazine release button, 2.892 in over the grip's bottom face (the button's black on Blackstone's OD green grip, its box 764 to 903 by 748 to 834 px, middle y -1.13 in the frame's pin frame, 319.7 px/in; grip_bottom_y -4.022): 1.763 times 2.892 / 3.129. An inference, not a reading: it takes the TX22's catch to be the button's own cross-bolt, engaging the notch at the button's height, which no page on file says; and the mark taken for the notch is a small square recess at the body's front edge a third of the way down, on both sides."}}],"adopt":{"from":"release","reason":"What the magazine has to fit (CLAUDE.md: two readings that can't both be true are decided by what the part has to fit, and both stay): at the seated reading's scale its catch notch stands 0.24 in over the release button that holds it, its top 0.26 in over the bore's axis inside the slide (0.19 cubic inches of the slide's body), where the round under its lips has to lie under the breech, and its pad 1.28 in wide for the pistol's published 1.25 at its widest point; at this one the notch is at the button, the top 0.10 under the bore's axis and the pad 1.19 wide. The seated reading (the black pad under Blackstone's OD green grip, 1.763 on the rail's pitch, 1.73 on the frame's pins) is 8% longer than the pad of every picture of 358-0017-01 alone at this scale: which of the two pads is the odd one isn't known (the part's gaps; asked of the orchestrator, 2026-11-05)."}},"rake":{"label":"The body's lean from upright over a level pad, its top toward the muzzle","kind":"angle","measurements":[{"id":"photo","value":12.119,"unit":"deg","pm":0.8,"source":{"type":"photo","photo":"references/taurus-tx22-magazine-22 fb7549e66665 (Gun Mag Warehouse, the 16-round from its right (2000 x 2000), standing on its pad, the front at the right)","scaleRef":"scale from taurus-tx22-magazine-16.base_pad_length = 1.763 in (median width over 0.94–0.985 of the height from the top, 574–622 px 618 px → 350.3 px/in)","method":"angle from the vertical of the straight line through the outline in x [-0.5, 0.7] in y [1.0, 4.4] (3.47 in of it, rms 0.001) of the traced outline (tools/trace.py); the body's front edge, the straight line through the outline between 1.0 and 4.4 in above the pad's bottom: its angle from the vertical, with the pad level","via":"harvest"}}],"note":"Read on the one square view of the 16-round standing on its pad. Five other views of it read 11.1 to 13.3 degrees (Galati 12.7, Shiner 12.9, Primary Arms 13.3, Midwest Gun Works 11.1, Taurus 12.9: ratios.py, from their edges in pixels, each a little from above or ahead): the ± takes them. The frame's own reading of its well's lean, from the front strap, is 14.5 ± 1.5 (taurus-tx22-frame.magwell_rake), 2.4 degrees more."},"body_front_to_back":{"label":"The body's front to back, level (along the pistol), as it leans in the grip","kind":"length","measurements":[{"id":"photo","value":1.185,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/taurus-tx22-magazine-22 fb7549e66665 (Gun Mag Warehouse, the 16-round from its right (2000 x 2000), standing on its pad, the front at the right)","scaleRef":"scale from taurus-tx22-magazine-16.base_pad_length = 1.63 in (median width over 0.94–0.985 of the height from the top, 574–622 px 618 px → 378.9 px/in)","method":"median row width in y [1.2, 3.4] (1.179–1.193) of the traced outline (tools/trace.py); the body's front to back, level (across the pistol's x), the median of its rows between 1.2 and 3.4 in above the pad's bottom","via":"harvest"}}]},"body_across":{"label":"The body's front to back square across its own length","kind":"length","measurements":[{"id":"derived","value":1.159,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.body_front_to_back} * cos({.rake})","via":"harvest"},"note":"The level width of a body leaning by the rake, taken square across it: what a picture of the body standing upright shows (the 22-round's, taurus-tx22-magazine-22)."}]},"pad_top_rise":{"label":"The pad's top: how much it rises toward the muzzle over its level bottom","kind":"angle","measurements":[{"id":"seated","value":1,"unit":"deg","pm":0.9,"source":{"type":"derived","expr":"90 - {.pad_top_lean}","via":"harvest"},"note":"As it lies on the grip's bottom face in Blackstone's view, against the rail's line (the grip's edge over it rises 3 px over 320 toward the front, the rail falls 1 px over 128); its sign is read on the picture, the lean is unsigned. Gun Mag Warehouse's view of the magazine alone has the near rim of its top rising 30 px over 500 (3.4 degrees) over a level bottom, a view from above in which a near rim leans with the lens; the frame's owner reads the grip's bottom face rising 2.4 degrees between two points (-4.04 at x -2.4, -3.98 at x -0.95) in the pin frame, whose line is 1.27 degrees off the slide's."}]},"pad_front_ahead":{"label":"The pad's nose ahead of the body's front face, at the pad's top","kind":"length","measurements":[{"id":"photos","value":0.384,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/taurus-tx22-magazine-22 fb7549e66665 (Gun Mag Warehouse), references/taurus-tx22-magazine-16 267f27d5a9e7 (Galati), 65ab616db6aa (Shiner Tactical), c1ad10af2292 (Primary Arms): the 16-round standing on its pad, from the side","scaleRef":"each picture's own pad length (its lowest rows' longest run), taurus-tx22-magazine-16.base_pad_length = 1.630 in (its adopted reading)","method":"the body's front edge, a line fitted to its rows between 0.30 and 0.75 of the height, carried down to 0.155 pad lengths over the pad's bottom (the pad's top at the front, below_grip 0.272 plus the top's rise); the nose's foremost point ahead of it: 0.238, 0.235, 0.234, 0.228 pad lengths (.cache/tx22/taurus-tx22-magazine-16/scripts/nose.py)","via":"harvest"}}],"note":"Where the frame's magwell_x is checked against: the nose shows under the grip in the pistol's photos, the body's front doesn't."},"body_width":{"label":"The body's width across (z), square across it","kind":"length","measurements":[{"id":"end","value":0.64,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/taurus-tx22-magazine-22 25b0a3efc4e2 (Taurus shop 08: the 22-round, whose body this is, from one end, standing on its base plate, turned some 5 degrees)","scaleRef":"taurus-tx22-magazine-22.axis_height = 6.183 in over its 1057 px (170.9 px/in)","method":"the body's face between its left edge (column 525) and the lit corner where its right side begins (634): 109 px = 0.638 in, over the cosine of the turn (the side's strip beside it, 17 px = 0.099 in, is body_across times its sine: 4.9 degrees); picked on a tile enlarged four times with its pixel grid (.cache/tx22/taurus-tx22-magazine-22/end_body_grid.png)","via":"harvest"}}]},"inside_width":{"label":"The inside's width across (z): the room the rounds stand in","kind":"length","measurements":[{"id":"assumed","value":0.4,"unit":"in","pm":0.08,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view looks into the body. American Rifleman (its T.O.R.O. review): the TX22 is a pistol \"sporting magazines with more ammunition capacity than traditional single-stack designs\", so the rounds stand staggered, not one rim over the next; the inside is taken half as wide again as a .22 LR's rim (about a quarter of an inch: not on file), the side walls the rest of body_width. Read through the slots in every side view, where the slot's inner walls show lit."}}]},"inside_length":{"label":"The inside's length front to back, square across the body","kind":"length","measurements":[{"id":"assumed","value":1.03,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: a round's length and a little (a .22 LR round is about an inch long: not on file), the front and rear walls the rest of body_across, alike."}}]},"follower_depth":{"label":"How far down from the body's top the inside is closed (the follower and the lips, as an empty magazine has them)","kind":"length","measurements":[{"id":"assumed","value":0.45,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: an empty magazine's follower stands at the top of its travel, its buttons at the slot's top (the button's hole is 0.45 to 0.75 in under the body's top on profiles.body), and the model is solid from there up."}}]},"button_proud":{"label":"How far the follower's button stands out of the side","kind":"length","measurements":[{"id":"assumed","value":0.06,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the buttons show from the side (Gun Mag Warehouse's view fb7549e66665) and only as a nub from above (Primary Arms' view down the body, 4fc813f2174e), where nothing scales them."}}]},"catch_notch_depth":{"label":"How deep the catch's notch is cut into each side at the front","kind":"length","measurements":[{"id":"assumed","value":0.06,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the notch shows as a dark rectangle on the side at the front edge (its place and size on profiles.body), and no view shows it end on."}}]},"pad_top_lean":{"label":"The pad's top under the grip: its angle from the vertical in the pistol's side view (the rail level)","kind":"angle","measurements":[{"id":"seated","value":88.997,"unit":"deg","pm":0.895,"source":{"type":"photo","photo":"references/taurus-tx22-toro 9efc84da32c0 (Blackstone Shooting's T.O.R.O. with an OD green frame from its right (2500 x 1844), square on: the 16-round's black pad under the grip)","scaleRef":"frame from the reviewed holes slot_rear, slot_front (324.2 px/in, rms 0.000 in over 2 points)","method":"angle from the vertical of the straight line through the outline in x [-5.75, -4.75] in y [-3.47, -3.38] (1.00 in of it, rms 0.006) of the traced outline (tools/trace.py); the pad's top, where the grip's bottom edge lies on it, between its rear end and the nose's rise: the straight line through the outline there, its angle from the vertical (the rail's line level)","via":"harvest"}}]},"pad_width":{"label":"pad width","kind":"length","measurements":[{"id":"photo","value":1.186,"unit":"in","pm":0.029,"source":{"type":"photo","photo":"references/taurus-tx22-magazine-16 7ebe9ab55fee (Primary Arms 358-0017-01_03, the pad from below (2200 x 1467), the front at the right)","scaleRef":"scale from taurus-tx22-magazine-16.base_pad_length = 1.63 in (x-extent 1742 px → 1068.7 px/in)","method":"height of the traced outline (tools/trace.py); the pad's width across, from below, scaled by its length as seated","via":"harvest"}}]},"groove_depth":{"label":"How deep the channel down each side, ahead of the slot, is cut","kind":"length","measurements":[{"id":"assumed","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the channel shows as a dark floor between two lit walls on the square side view (its place and width on profiles.body), and no view shows it end on (Taurus's end view is turned 5 degrees, its side's strip too narrow to read a step in)."}}]},"plug_ring_depth":{"label":"How deep the ring round the pad's plug is, under its underside","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the ring shows dark round the plug on the view from below (its place and width on profiles.plan), and no view shows it in profile."}}]},"dimple_depth":{"label":"How deep the dimple near the pad's nose is","kind":"length","measurements":[{"id":"assumed","value":0.015,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: a shaded spot on the view from below, as Handguns' view of the seated pad has it too (9e7b75ff19e1); no view shows it in profile."}}]}}},{"subject":"taurus-tx22-magazine-22","title":"Taurus TX22 .22LR 22-round magazine","dimensions":{"overall_height":{"label":"Overall height, feed lips to base","kind":"length","measurements":[{"id":"square","value":6.157,"unit":"in","pm":0.12,"source":{"type":"photo","photo":"references/taurus-tx22-magazine-22 c468e0cbc9ec (Gun Mag Warehouse, the 22-round from its right, square on)","scaleRef":"taurus-tx22-magazine-16.body_front_to_back = 1.185 in (the body's rows, 213 px)","method":"profiles.side's height (turned to taurus-tx22-magazine-16.rake), its top 4.392 over the seat and its base plate's front lower corner 1.765 under it (the model's bounds)","via":"harvest"}}],"note":"As the magazine stands in the grip (its body leaning by the rake): the base plate's lowest corner to the body's highest point."},"below_grip":{"label":"How far it stands below the grip, seated: the sleeve and the base plate, at the front","kind":"length","measurements":[{"id":"square","value":1.765,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/taurus-tx22-magazine-22 c468e0cbc9ec (Gun Mag Warehouse, the 22-round from its right, square on)","scaleRef":"taurus-tx22-magazine-16.body_front_to_back = 1.185 in (the body's rows, 213 px)","method":"profiles.side, turned to the rake: the sleeve's top where the body's front meets it (the seat) down to the base plate's front lower corner; at the rear the sleeve's foot is 0.25 in higher (its base is square to the leaning body)","via":"harvest"}}]},"weight":{"label":"Weight, empty","kind":"mass","measurements":[{"id":"rifleconfigurator","value":3.4,"unit":"oz","pm":0.05,"stated":"Weight 3.4 oz","source":{"type":"spec","publisher":"retailer","name":"Rifle Configurator, Taurus TX22 22rd mag (its catalog card)","url":"https://www.rifleconfigurator.com/catalog/magazines/taurus-tx22-22rd-mag","retrieved":"2026-11-05","via":"harvest"},"note":"A catalog's field, with no source of its own named; its 'Features' line says 'Polymer body, steel internals'."},{"id":"model","value":1.721,"unit":"oz","pm":0.7,"source":{"type":"derived","basis":"The model's polymer volume, 2.6125 cubic inches (its manifest's volume_in3: the body 1.497, the sleeve 0.691, the base plate 0.426), times std.density.polymer (Zytel nylon 66, 18.68 g, 0.6589 oz to the cubic inch): 1.721 oz. A glass-filled grade is up to a sixth heavier; the insides are assumed (the body's column of rounds, the sleeve's walls); the steel spring isn't in it. The ± takes them.","via":"harvest"}}],"adopt":{"from":"model","reason":"The model's own polymer, its insides assumed: Rifle Configurator's 3.4 oz names no source and is 1.7 oz over it (outside the ±: kept as the conflict it is, and in the part's gaps); the shipping fields are `shipping_weight`."},"note":"No page weighs the magazine as Taurus does: Rifle Configurator's 3.4 oz is a catalog's field with no source named; Copsplus' 0.25 lb and KYGUNCO's 2 lb are shipping fields (`shipping_weight`, beside this). The model's polymer is the figure used (its id `model`, written when the model is built)."},"shipping_weight":{"label":"Weight as shipped (sellers' shipping fields)","kind":"mass","measurements":[{"id":"copsplus","value":0.25,"unit":"lb","stated":"\"weight\":{\"formatted\":\"0.25 LBS\",\"value\":0.25}","source":{"type":"spec","publisher":"retailer","name":"Copsplus, Taurus 358-0034-00 TX22 Magazine, 22 LR, Black, 22 Round (its product record, sku KINS-1212002)","url":"https://copsplus.com/handgun-magazines/taurus-358-0034-00-tx22-magazine-22-lr-black-22-round/","retrieved":"2026-11-05","via":"harvest"},"note":"A distributor's record, in the shop's page data: a shipping weight."},{"id":"kygunco","value":2,"unit":"lb","stated":"Weight 2 lb","source":{"type":"spec","publisher":"retailer","name":"KYGUNCO, Taurus TX22 22rd Magazine (item 258267)","url":"https://www.kygunco.com/product/taurus-tx22-22rd-magazine","retrieved":"2026-11-05","via":"harvest"},"note":"The shop's shipping class: the same 2 lb is on its 16-round's page."}],"adopt":{"from":"copsplus","reason":"The lightest of the shipping fields, adopted only so the entry resolves: none of them is the magazine's weight."},"note":"What sellers give in their shipping fields, kept beside the magazine's weight and not in it (D104: a shipping class of 2 lb under `weight` widened the pistol's weight to 60 oz by its sources). Not used for anything; with more than one figure the lightest is adopted only so the entry resolves."},"capacity":{"label":"Capacity","kind":"count","measurements":[{"id":"taurus","value":22,"unit":"count","stated":"Genuine Taurus TX22 .22LR 22-round magazine","source":{"type":"spec","publisher":"manufacturer","name":"Taurus (shoptaurus.com), Genuine Taurus TX22 .22LR 22-round magazine (SKU 358-0034-00)","url":"https://shoptaurus.com/new-items/taurus-tx22-22lr-magazine-22-rounds","retrieved":"2026-11-05","via":"harvest"}},{"id":"primary-arms","value":22,"unit":"count","stated":"Taurus TX22 Magazine - .22 LR - 22 Round","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Taurus TX22 Magazine - .22 LR - 22 Round (SKU 358-0034-00)","url":"https://www.primaryarms.com/taurus-tx22-22-lr-22rd-magazine","retrieved":"2026-11-05","via":"harvest"}}],"adopt":{"from":"taurus","reason":"The maker's own shop; the seller says the same."},"note":"Taurus, of this magazine: \"This factory magazine uses the same body as the standard TX22 16-round magazine with a +6 round extension\"; and \"This magazine is compatible with TX22 platform pistols but may leave a small gap between the base plate and frame when used with the TX22 Compact.\" (its shop's page, read on the harvested copy)."},"axis_height":{"label":"Its length along the body, base plate's underside to the body's top","kind":"length","measurements":[{"id":"photo","value":6.183,"unit":"in","pm":0.161,"source":{"type":"photo","photo":"references/taurus-tx22-magazine-22 c468e0cbc9ec (Gun Mag Warehouse, the 22-round from its right (1280 x 1280), the body upright, square on)","scaleRef":"scale from taurus-tx22-magazine-16.body_across = 1.159 in (median width over 0.15–0.6 of the height from the top, 208–210 px 209 px → 180.3 px/in)","method":"height of the traced outline (tools/trace.py); the magazine's length along its body, base plate's underside to the body's top, as it stands upright on its base plate (the base plate is square to the body)","via":"harvest"}}]},"sleeve_length":{"label":"The sleeve's front to back, square across the body","kind":"length","measurements":[{"id":"photo","value":1.508,"unit":"in","pm":0.042,"source":{"type":"photo","photo":"references/taurus-tx22-magazine-22 c468e0cbc9ec (Gun Mag Warehouse, the 22-round from its right (1280 x 1280), the body upright, square on)","scaleRef":"scale from taurus-tx22-magazine-16.body_across = 1.159 in (median width over 0.15–0.6 of the height from the top, 208–210 px 209 px → 180.3 px/in)","method":"median row width in y [0.2, 1.2] (1.503–1.525) of the traced outline (tools/trace.py); the sleeve's front to back square across the body, the median of its rows between 0.2 and 1.2 in above the base's underside","via":"harvest"}}]},"body_width":{"label":"The body's width across (z): the 16-round's body","kind":"length","measurements":[{"id":"derived","value":0.64,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"{taurus-tx22-magazine-16.body_width}","via":"harvest"},"note":"Taurus: \"the same body as the standard TX22 16-round magazine\"; read on this magazine's own end view."}]},"sleeve_width":{"label":"The sleeve's width across (z)","kind":"length","measurements":[{"id":"end","value":1.115,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/taurus-tx22-magazine-22 25b0a3efc4e2 (Taurus shop 08: the 22-round from one end, standing on its base plate, turned some 5 degrees)","scaleRef":"taurus-tx22-magazine-22.axis_height = 6.183 in over its 1057 px (170.9 px/in)","method":"the sleeve's face between its left edge (column 484) and the lit corner where its right side begins (674): 190 px = 1.112 in, over the cosine of the turn (its side's strip, 20 px, is sleeve_length times the sine of 4.5 degrees; the body's gives 4.9); picked on a tile enlarged four times with its pixel grid (.cache/tx22/taurus-tx22-magazine-22/end_sleeve_grid.png)","via":"harvest"}}]},"inside_width":{"label":"The inside's width across (z): the 16-round's body's","kind":"length","measurements":[{"id":"derived","value":0.4,"unit":"in","pm":0.08,"source":{"type":"derived","expr":"{taurus-tx22-magazine-16.inside_width}","via":"harvest"},"note":"The 16-round's body's (an assumption there)."}]},"inside_length":{"label":"The inside's length front to back: the 16-round's body's","kind":"length","measurements":[{"id":"derived","value":1.03,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{taurus-tx22-magazine-16.inside_length}","via":"harvest"},"note":"The 16-round's body's (an assumption there)."}]},"sleeve_wall":{"label":"The sleeve's walls","kind":"length","measurements":[{"id":"assumed","value":0.08,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view looks into the sleeve; the end view shows a raised rim round the body where it enters the sleeve's top, and the sleeve holds the spring's extra length and the six more rounds."}}]},"follower_depth":{"label":"How far down from the body's top the inside is closed (the 16-round's)","kind":"length","measurements":[{"id":"derived","value":0.45,"unit":"in","pm":0.1,"source":{"type":"derived","expr":"{taurus-tx22-magazine-16.follower_depth}","via":"harvest"}}]},"catch_notch_depth":{"label":"How deep the catch's notch is cut into each side at the front (the 16-round's)","kind":"length","measurements":[{"id":"derived","value":0.06,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{taurus-tx22-magazine-16.catch_notch_depth}","via":"harvest"}}]},"step_depth":{"label":"How far the sleeve's side under its diagonal edge stands in from the face over it","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the edge shows lit on every view of the side (Gun Mag Warehouse c468e0cbc9ec, Taurus b9b473b2a84b, 83c10f0c7119) and no view shows it end on."}}]},"panel_depth":{"label":"How far the textured panel stands in from the face round it","kind":"length","measurements":[{"id":"assumed","value":0.015,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the panel's border shows as a fine shadowed line on the side views; its texture isn't drawn."}}]},"groove_depth":{"label":"How deep the channel down each side is cut (the 16-round's body's)","kind":"length","measurements":[{"id":"derived","value":0.03,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{taurus-tx22-magazine-16.groove_depth}","via":"harvest"}}]}}},{"subject":"taurus-tx22-thread-protector","title":"Taurus TX22 thread protector","dimensions":{"length":{"label":"Length ahead of the barrel's shoulder, installed (to the front face; a washer's thickness included)","kind":"length","measurements":[{"id":"overall","value":0.527,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{taurus-tx22-frame.rear_x} + {taurus-tx22-frame.pistol_overall_length} - {taurus-tx22-frame.slide_rear_x} - {taurus-tx22-toro-slide.length}","via":"harvest"}}],"note":"From its rear face on the barrel's shoulder (at the slide's front face, where it goes out of sight) to its front face, where the pistol's published overall length puts it (the frame's rearmost point plus 7.60). The left view's silhouette reads 0.51 from the slide's face (the slide's near face and the protector's middle plane each at its own scale), Blackstone's 0.58 less its shorter slide face."},"od":{"label":"Largest outside diameter","kind":"length","measurements":[{"id":"left","value":0.59,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/taurus-tx22-toro f0237849b397 (Sportsman's Warehouse 1883977-2: the T.O.R.O. from its left)","scaleRef":"the pin frame at the middle plane (158.8 px/in on the near face, 1.7% less on the middle plane: 156.1)","method":"the silhouette 92 px high (rows 253 to 344, grey under 200) all along from 0.06 in behind its front face to the slide's face","via":"harvest"}},{"id":"right","value":0.6,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/taurus-tx22-toro e50c634c3e4d (Sportsman's Warehouse 1883977-1: the T.O.R.O. from its right)","scaleRef":"the pin frame at the middle plane (157.2 px/in on the near face, 1.7% less: 154.6)","method":"the silhouette 93 to 94 px high all along","via":"harvest"}}],"adopt":{"from":"left","reason":"The left view isn't yawed (the right is, some 5 degrees); the two agree within their ±."},"note":"Its silhouette over its length in the three side views (0.585 to 0.600 across, the frame's owner's reading): its wrench flats turn with how far it was screwed on, and across flats and across corners differ."},"flats_length":{"label":"The wrench flats' length, from the rear face","kind":"length","measurements":[{"id":"left","value":0.357,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.length} - {.round_length}","via":"harvest"}}],"note":"The flats end at a lit line round the protector 0.17 in behind its front face in both side views (column 30 to 32 in the left, 1164 to 1166 in the right); behind it the obliques show the flats, ahead of it the round front."},"round_length":{"label":"The round front, behind its front face","kind":"length","measurements":[{"id":"left","value":0.17,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/taurus-tx22-toro f0237849b397 (Sportsman's Warehouse 1883977-2: the T.O.R.O. from its left)","scaleRef":"the pin frame at the middle plane (156.1 px/in)","method":"the lit line round it at columns 30 to 32 against its front face's tip at column 3 to 4: 27 px","via":"harvest"}}]},"front_round":{"label":"The rounding of its front edge (its radius)","kind":"length","measurements":[{"id":"left","value":0.07,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/taurus-tx22-toro f0237849b397 (Sportsman's Warehouse 1883977-2: the T.O.R.O. from its left)","scaleRef":"the pin frame at the middle plane (156.1 px/in)","method":"the silhouette's front comes to its full height over 11 px (columns 3 to 14: 46 px high at its tip, 90 at column 14)","via":"harvest"}}]},"across_flats":{"label":"Across its wrench flats","kind":"length","measurements":[{"id":"assumed","value":0.565,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: six shallow flats (a hexagon in the left-front oblique, d4f6e257c86f) cut into the round, their corners left standing: the silhouette reads 0.585 to 0.600 in three views of two protectors however each was screwed on, so the flats take off little of it (a flat on top would read its own width). Over a 1/2-28 thread they leave a wall of some 0.03.","via":"harvest"}}]},"hole_d":{"label":"The hole in its front face","kind":"length","measurements":[{"id":"oblique","value":0.25,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/taurus-tx22-toro 7c0111a45816 (Sportsman's Warehouse 1883977-8: the T.O.R.O. from its right front and above)","scaleRef":"its own front face's rim (an ellipse 90 x 145 px for 0.59 in)","method":"the dark hole about 62 px high in the 145 px rim","via":"harvest"}}]},"front_wall":{"label":"Its front wall's thickness (ahead of the barrel's muzzle face)","kind":"length","measurements":[{"id":"assumed","value":0.06,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: a cap's front wall, the barrel's muzzle face behind it (the hole in the face is larger than the bore and shows no thread).","via":"harvest"}}]},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"model","value":0.23,"unit":"oz","pm":0.05,"source":{"type":"derived","basis":"The model's steel, 0.0506 cubic inches (pipeline/blender/taurus_tx22_thread_protector.py's manifest), times std.density.steel (4.565 oz to the cubic inch): 0.231 oz. No page names its metal; it is a steel's look in every photo. The ± is its assumed flats and front wall. app/tests/taurus-tx22-thread-protector.test.ts holds the model's volume to it.","via":"harvest"}}],"note":"No page weighs it. Worked out from the model's steel."}}},{"subject":"taurus-tx22-toro-slide","title":"Taurus TX22 T.O.R.O. slide","dimensions":{"length":{"label":"Length, rear face to front face","kind":"length","measurements":[{"id":"photo","value":6.929,"unit":"in","pm":0.049,"source":{"type":"photo","photo":"references/taurus-tx22-toro f0237849b397 (Sportsman's Warehouse 1883977-2: the T.O.R.O. from its left, the muzzle at the left, 1200 x 1200)","scaleRef":"frame from the reviewed holes rear_pin, front_pin (158.1 px/in, rms 0.000 in over 2 points)","method":"x_max in y [-0.2, 0.35] of the traced outline (tools/trace.py); the front face's near edge, below the top chamfer and clear of the protector (rows over -0.2 to 0.35 in)","via":"harvest"}}],"note":"From the rear face at the bore's height (the face leans, its foot further back) to the front face. Both ends are the near face's silhouette in the left view."},"height":{"label":"Height above the bore axis to the slide's top","kind":"length","measurements":[{"id":"photo","value":0.514,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/taurus-tx22-toro f0237849b397 (Sportsman's Warehouse 1883977-2: the T.O.R.O. from its left, the muzzle at the left, 1200 x 1200)","scaleRef":"frame from the reviewed holes rear_pin, front_pin (158.1 px/in, rms 0.000 in over 2 points)","method":"y_max in x [4.7, 6.2] of the traced outline (tools/trace.py); the nose's top behind the front sight: the far top edge, which a view from even 2 degrees above lifts by some 0.03 in against the near face (the ± takes it)","via":"harvest"}}]},"bottom_below_axis":{"label":"The slide's lower edge below the bore axis (where it rides on the frame)","kind":"length","measurements":[{"id":"seam","value":0.302,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{taurus-tx22-frame.bore_axis_y} - {taurus-tx22-frame.seam_y}","via":"harvest"}},{"id":"left-shadow","value":0.268,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/taurus-tx22-toro f0237849b397 (Sportsman's Warehouse 1883977-2: the T.O.R.O. from its left, the muzzle at the left, 1200 x 1200)","scaleRef":"the pin frame (the two cross pins' ends at 735.0, 372.0 and 520.8, 367.0: 158.8 px/in on the near face), shifted to the slide's frame by taurus-tx22-frame.slide_rear_x and bore_axis_y","method":"the start of the dark line under the slide at x 0.5 to 6.5 (rows 337 to 343 against the protector's middle at row 298.5): the shadowed lower edge, not the frame's top","via":"harvest"}}],"adopt":{"from":"seam","reason":"The seat is the frame's: the slide's lower edge lies on the frame's top where the frame's owner reads it in all three views (0.165, 0.162, 0.171 over the rear pin), so the two parts touch there and no slit shows. The dark line's top is the slide's lower edge in shadow, a chamfer's height above where it meets the frame."},"note":"The seat on the frame: the frame states where the slide's lower edge is (taurus-tx22-frame.seam_y, the frame's top along its side faces), and the slide carries the same figure as its own lower edge under its own origin. The left view's dark line at the seam begins a few pixels higher (0.268 below the axis): it is the slide's shadowed lower edge over the frame's lit top, which the frame's owner reads as the seam in all three views."},"width":{"label":"Width (across its sides)","kind":"length","measurements":[{"id":"oblique","value":0.93,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/taurus-tx22-toro 7c0111a45816 (Sportsman's Warehouse 1883977-8: the T.O.R.O. from its right front and above, 1200 x 1200)","scaleRef":"the thread protector's front face (its rim an ellipse 90 px across and 145 px high: across, its 0.59 in silhouette, taurus-tx22-thread-protector.od)","method":"the front face 125 px between its near corner facet and its far silhouette on row 360, at the protector's 90 px for 0.59 in, less 2% for the face standing behind the protector's (0.84 in), and a corner facet each side as deep as it is long (0.045 in on the left view): 0.93. The ± takes the facets' angle and the protector's flats (its silhouette across flats and across corners differ).","via":"harvest"}}],"note":"No view square across the slide. In the right-front oblique (7c0111a45816), at row 360 the slide's front face runs from a lit band at its near corner (945 to 976) to its far silhouette (1101): 125 px, with the protector's front face 90 px across on the same rows (0.59 in, its silhouette): 0.82 in, 0.84 for the face standing some 0.5 in further from the lens. The corner facets are taken as deep across as their length along on the left view (the front face's near edge at 75.5, the side face's at 82.5: 0.045 in each), adding 0.09. A doubt the ± has to take: row 360 is within the nose's upper bevels at the front (the far silhouette leans from row 315 to 393, nose_bevel_across), so the far edge read there may be on the far bevel, 0.07 inside the full width, and the near band may be the near bevel rather than a corner facet: read so, the width is 0.84 + 2 x 0.07 = 0.98. Below the bevels the protector hides the far edge. Not checked against an independent figure: the frame's owner takes its body's width from this one (taurus-tx22-frame.body_width)."},"front_corner":{"label":"The facet on each of the front face's vertical corners, its length along the slide","kind":"length","measurements":[{"id":"left","value":0.045,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/taurus-tx22-toro f0237849b397 (Sportsman's Warehouse 1883977-2: the T.O.R.O. from its left)","scaleRef":"the pin frame (158.8 px/in on the near face)","method":"the front face's near edge at column 75.5 and the side face's at 82.5 above the protector (rows 235 to 250): 7 px","via":"harvest"}}],"note":"A lit band at each front corner, between the front face and the side, in both obliques (the right-front one's at row 360: 945 to 976 px). Across, it is taken as deep as it is long (45 degrees)."},"nose_bevel_rear_y":{"label":"The nose's upper bevel: its lower edge on the side at the nose's rear face, above the bore axis","kind":"length","measurements":[{"id":"left","value":0.274,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/taurus-tx22-toro f0237849b397 (Sportsman's Warehouse 1883977-2: the T.O.R.O. from its left)","scaleRef":"the pin frame (158.8 px/in on the near face), shifted to the slide's frame","method":"the band's lower edge at row 256 at column 470 and 273.5 at columns 85 to 95, against the protector's middle at row 298.5; the line through them at the nose's rear face (4.263)","via":"harvest"}}],"note":"The nose's upper sides are bevelled the length of the nose, the \"TX\" on the bevel: a lit band from the top down to row 256 at the nose's rear and 273 to 274 at its front in the left view (grey 133 to 150 against the side's 60 to 70 under it); the rear block's chamfer is the narrow band (top_chamfer). The bevel's lower edge is read at columns 470 (x 4.39) and 85 to 95 (x 6.80) and carried on in a line to the nose's two ends."},"nose_bevel_front_y":{"label":"The nose's upper bevel: its lower edge on the side at the front face, above the bore axis","kind":"length","measurements":[{"id":"left","value":0.151,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/taurus-tx22-toro f0237849b397 (Sportsman's Warehouse 1883977-2: the T.O.R.O. from its left)","scaleRef":"the pin frame (158.8 px/in on the near face), shifted to the slide's frame","method":"the same line at the front face (6.929)","via":"harvest"}}]},"nose_bevel_across":{"label":"The nose's upper bevel: its lean from upright","kind":"angle","measurements":[{"id":"oblique","value":23,"unit":"deg","pm":5,"source":{"type":"photo","photo":"references/taurus-tx22-toro 7c0111a45816 (Sportsman's Warehouse 1883977-8: the T.O.R.O. from its right front and above)","scaleRef":"the thread protector's front face (an ellipse 90 px across and 145 px high for its 0.59 in silhouette)","method":"the far silhouette's lean (column 1083 at row 315 to 1113 at 393) less the front sight's vertical edges' (0.10 px a px), across and up at the protector's two scales: 0.42, atan 23 degrees","via":"harvest"}}],"note":"In the right-front oblique the slide's far silhouette below its front top corner (rows 315 to 393, the bevel's height at the front) leans 0.36 px across for each px down where the front sight's vertical edges lean 0.10; the difference at the scales the protector's front face gives across (152.5 px/in) and up (246) is 0.42 in across for each inch down: 23 degrees from upright. The front top edge between the two bevels then reads 0.69 (105 px), against 0.65 from this slope."},"top_chamfer":{"label":"The chamfer along each top edge, its height on the side","kind":"length","measurements":[{"id":"left","value":0.07,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/taurus-tx22-toro f0237849b397 (Sportsman's Warehouse 1883977-2: the T.O.R.O. from its left, the muzzle at the left, 1200 x 1200)","scaleRef":"the pin frame (the two cross pins' ends at 735.0, 372.0 and 520.8, 367.0: 158.8 px/in on the near face), shifted to the slide's frame by taurus-tx22-frame.slide_rear_x and bore_axis_y","method":"the lit band under the top edge over the rear block (rows 217 to 233, 0.10 in), less the far top edge's lift against the near face for a view a degree or two above (0.03)","via":"harvest"}}],"note":"In the left view the lit band under the top runs from row 217 to 233 over the rear block (16 px), less the far top edge's lift (0.03 in): 0.07. Across, it is taken as deep as it is high (45 degrees: no end view)."},"nose_rear_x":{"label":"The nose's slanted rear face, just under its top","kind":"length","measurements":[{"id":"photo","value":4.263,"unit":"in","pm":0.031,"source":{"type":"photo","photo":"references/taurus-tx22-toro f0237849b397 (Sportsman's Warehouse 1883977-2: the T.O.R.O. from its left, the muzzle at the left, 1200 x 1200)","scaleRef":"frame from the reviewed holes rear_pin, front_pin (158.1 px/in, rms 0.000 in over 2 points)","method":"x_min in x [3.8, 5.0] in y [0.38, 0.47] of the traced outline (tools/trace.py); the nose's slanted rear face just under its top","via":"harvest"}}]},"rear_block_front_x":{"label":"The rear block's front face, just under its top","kind":"length","measurements":[{"id":"photo","value":3.02,"unit":"in","pm":0.023,"source":{"type":"photo","photo":"references/taurus-tx22-toro f0237849b397 (Sportsman's Warehouse 1883977-2: the T.O.R.O. from its left, the muzzle at the left, 1200 x 1200)","scaleRef":"frame from the reviewed holes rear_pin, front_pin (158.1 px/in, rms 0.000 in over 2 points)","method":"x_max in x [2.3, 3.5] in y [0.38, 0.47] of the traced outline (tools/trace.py); the rear block's front face just under its top","via":"harvest"}}]},"wall_top":{"label":"The left wall's top in the open middle section, above the bore axis","kind":"length","measurements":[{"id":"photo","value":0.004,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/taurus-tx22-toro f0237849b397 (Sportsman's Warehouse 1883977-2: the T.O.R.O. from its left, the muzzle at the left, 1200 x 1200)","scaleRef":"frame from the reviewed holes rear_pin, front_pin (158.1 px/in, rms 0.000 in over 2 points)","method":"y_max in x [3.3, 3.9] of the traced outline (tools/trace.py); the left wall's lit rim in the open middle section, under the chamber block","via":"harvest"}}]},"port_floor":{"label":"The ejection port's rim in the right wall, below the bore axis","kind":"length","measurements":[{"id":"right","value":0.09,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/taurus-tx22-toro e50c634c3e4d (Sportsman's Warehouse 1883977-1: the T.O.R.O. from its right, the muzzle at the right)","scaleRef":"the pin frame (rear 452.5, 382.5; front 664.5, 374.5: 157.2 px/in)","method":"the port's rim at rows 322 to 323 between x 510 and 628 against the protector's middle carried back along the slide's lower edge (row 297.5 at the muzzle, 309 at x 580: the photo is rolled 1.1 degrees): 0.09 below","via":"harvest"}}],"note":"The right wall cut down between the rear block and the nose, lower than the left wall: its lit rim at row 322 to 323 in the right view."},"breech_x":{"label":"Where the barrel's breech face stands, ahead of the slide's rear face","kind":"length","measurements":[{"id":"muzzle","value":2.796,"unit":"in","pm":0.06,"source":{"type":"derived","expr":"{taurus-tx22-frame.rear_x} + {taurus-tx22-frame.pistol_overall_length} - {taurus-tx22-frame.slide_rear_x} - {taurus-tx22-thread-protector.front_wall} - {taurus-tx22-barrel-46.stated_length}","via":"harvest"}}],"note":"The breech face isn't seen: the barrel's chamber block runs back under the rear block. Worked out from the barrel's published length, its muzzle face standing behind the protector's front wall, and the protector's front face where the pistol's published overall length puts it (the frame's rearmost point plus 7.60). The rear block's front face (rear_block_front_x) stands 0.1 to 0.2 ahead of it: the block's rear end goes into the slide's breech."},"top_window_front_x":{"label":"The top vent's front end (its rounded end's tip)","kind":"length","measurements":[{"id":"oblique","value":6.21,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/taurus-tx22-toro d4f6e257c86f (Sportsman's Warehouse 1883977-7: the T.O.R.O. from its left front and above)","scaleRef":"the front sight's rear end and the nose's rear step, both read on the left view (6.295, 4.317)","method":"the vent's front end at 235 px on the line from the sight's rear end (205) to the step (945), linearly","via":"harvest"}}],"note":"On the left-front oblique, along the nose's top between the front sight's rear end (6.295 on the left view) and the nose's rear step (4.317): the vent's ends at 235 and 878 px of the line from 205 to 945, taken linearly (perspective along 2 in of the top: a percent)."},"top_window_rear_x":{"label":"The top vent's rear end","kind":"length","measurements":[{"id":"oblique","value":4.5,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/taurus-tx22-toro d4f6e257c86f (Sportsman's Warehouse 1883977-7)","scaleRef":"the front sight's rear end and the nose's rear step, both read on the left view (6.295, 4.317)","method":"the vent's rear end at 878 px on the line from 205 to 945, linearly","via":"harvest"}}]},"top_window_width":{"label":"The top vent's width across","kind":"length","measurements":[{"id":"oblique","value":0.38,"unit":"in","pm":0.06,"source":{"type":"photo","photo":"references/taurus-tx22-toro d4f6e257c86f (Sportsman's Warehouse 1883977-7)","scaleRef":"the top's own width (.width less two .top_chamfer)","method":"the vent's dark opening 20 px of the top's 42 px band, square across the top at the vent's middle","via":"harvest"}}],"note":"Some 0.48 of the top's band between its near edge and its far silhouette at the vent's middle in the left-front oblique (20 px of 42): of the top flat inside the two chamfers (width less two chamfers)."},"window_depth":{"label":"How far the side vents reach across from each side","kind":"length","measurements":[{"id":"assumed","value":0.3,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: each side vent goes through its wall into the room round the barrel; the barrel shows in it in both side views.","via":"harvest"}}],"note":"They open into the barrel's bore through the side walls: the barrel shows through both."},"wall":{"label":"The side walls' thickness in the open middle section and under the nose","kind":"length","measurements":[{"id":"assumed","value":0.09,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the walls round the chamber block in the open middle section (the block fills the channel between them in the right-front oblique, 7c0111a45816).","via":"harvest"}}]},"bore_clearance":{"label":"Room round the barrel in the nose, on its radius","kind":"length","measurements":[{"id":"assumed","value":0.012,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: so that the barrel and the slide's bore share nothing. Not a fit.","via":"harvest"}}]},"underside_depth":{"label":"The channel up into the rear block's underside, from its lower edge","kind":"length","measurements":[{"id":"assumed","value":0.22,"unit":"in","pm":0.08,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the slide rides on the frame's rails, whose tabs stand up above the frame's top inside the slide (Taurus shop's photo of the kit, 98a3a34d1d2d: three tabs, the tallest some 0.2 in over the frame's top); the slide's underside is open between its walls to take them.","via":"harvest"}}]},"rear_end":{"label":"The rear block's solid rear end, ahead of its rear face, before the underside channel","kind":"length","measurements":[{"id":"assumed","value":0.12,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the rear face is whole in both side views and the kit's photo.","via":"harvest"}}]},"serration_depth":{"label":"The serrations' depth into the side","kind":"length","measurements":[{"id":"assumed","value":0.035,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view shows a groove where it meets an edge square on.","via":"harvest"}}]},"serration_count_front":{"label":"Front serrations: grooves each side","kind":"count","measurements":[{"id":"left","value":5,"unit":"count","source":{"type":"photo","photo":"references/taurus-tx22-toro f0237849b397 (Sportsman's Warehouse 1883977-2: the T.O.R.O. from its left, the muzzle at the left, 1200 x 1200)","scaleRef":"the pin frame (the two cross pins' ends at 735.0, 372.0 and 520.8, 367.0: 158.8 px/in on the near face), shifted to the slide's frame by taurus-tx22-frame.slide_rear_x and bore_axis_y","method":"counted on row 285 (five pairs of dark walls) and in both obliques","via":"harvest"}}]},"serration_count_rear":{"label":"Rear serrations: grooves each side","kind":"count","measurements":[{"id":"left","value":7,"unit":"count","source":{"type":"photo","photo":"references/taurus-tx22-toro f0237849b397 (Sportsman's Warehouse 1883977-2: the T.O.R.O. from its left, the muzzle at the left, 1200 x 1200)","scaleRef":"the pin frame (the two cross pins' ends at 735.0, 372.0 and 520.8, 367.0: 158.8 px/in on the near face), shifted to the slide's frame by taurus-tx22-frame.slide_rear_x and bore_axis_y","method":"counted on row 300 (seven dark rear walls, 918 to 1116 px, 33 px apart) and in both obliques","via":"harvest"}}]},"plate_width_inset":{"label":"The cover plate's sides, inside the slide's sides","kind":"length","measurements":[{"id":"assumed","value":0,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the plate as wide as the slide at the cut, its sides in the slide's chamfers.","via":"harvest"}}],"note":"The cut is open at both sides: the plate's side faces show in both side views, from the seam at the cut's floor up to its ramps' facets (ramp1_bevel_front and the rest). No view from the front or behind is on file; the left-front oblique (d4f6e257c86f) says the sides lean with the slide's chamfer rather than stand upright: in it, scaled across by the plate's two screws (screw_spacing) and along by the plate's length, the band of the plate's side at its front end shows 25 px from its top edge to the seam, where an upright side would show 13 to 15 and one in the slide's 45-degree chamfer 17 to 19 (neither exactly; the chamfer's nearer), and it is lit like no upright face of the slide in the right-front oblique (7c0111a45816: the band 156, the slide's flank under it 132). Drawn in the slide's chamfer (2026-11-06: drawn upright for an afternoon, which put the plate's corners out past the chamfer at both walls)."},"screw_head_d":{"label":"The cover plate's screw heads, across","kind":"length","measurements":[{"id":"oblique","value":0.17,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/taurus-tx22-toro d4f6e257c86f (Sportsman's Warehouse 1883977-7)","scaleRef":"the bumps the heads make on the left view's plate top, 20 px for the front screw (.cover_screws feature)","method":"the front screw's bump 20 px long on the left view's plate top at 158.8 px/in, less its shadow; the oblique's two Torx heads about a quarter of the plate's width","via":"harvest"}}]},"front_sight_width":{"label":"The front sight's width across","kind":"length","measurements":[{"id":"assumed","value":0.14,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the post in both obliques is narrow against the slide's top, its white dot most of its width.","via":"harvest"}}]},"rear_sight_width":{"label":"The rear sight's width across","kind":"length","measurements":[{"id":"assumed","value":0.6,"unit":"in","pm":0.08,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the right-front oblique (7c0111a45816) shows the sight across most of the slide's top flat, its notch in its middle.","via":"harvest"}}]},"rear_notch_width":{"label":"The rear sight's square notch, across","kind":"length","measurements":[{"id":"assumed","value":0.12,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: \"serrated, drift-adjustable square-notch rear sight\" (American Rifleman); the notch about a fifth of the sight's width in the right-front oblique.","via":"harvest"}}]},"lug_bottom":{"label":"The front lug's bottom below the bore axis","kind":"length","measurements":[{"id":"left","value":0.826,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/taurus-tx22-toro f0237849b397 (Sportsman's Warehouse 1883977-2: the T.O.R.O. from its left, the muzzle at the left, 1200 x 1200)","scaleRef":"the pin frame (the two cross pins' ends at 735.0, 372.0 and 520.8, 367.0: 158.8 px/in on the near face), shifted to the slide's frame by taurus-tx22-frame.slide_rear_x and bore_axis_y","method":"the lug's smooth face ahead of the frame's textured dust cover (x 76 to 88) to row 428 (profiles.side.features.front_lug, through the pin frame)","via":"harvest"}}],"note":"The lug under the nose that holds the recoil spring's front end (Taurus shop's photo of the kit): in the left view its face shows ahead of the frame's dust cover down to row 428, in the right view to 430."},"lug_length":{"label":"The front lug's length along the slide","kind":"length","measurements":[{"id":"kit","value":0.27,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/taurus-tx22-toro 98a3a34d1d2d (Taurus shop, the conversion kit: the slide with its barrel and spring lifted off a frame, from the left, 1200 x 984)","scaleRef":"the slide's own side height in the same photo (.height + .bottom_below_axis, 98 px at its rear block)","method":"its bottom 37 px long against the slide's side height of 98 px at the rear block (0.82 in: .height + .bottom_below_axis)","via":"harvest"}}],"note":"Only its front 0.08 in shows ahead of the frame's dust cover on the pistol: the rest stands inside the dust cover's front."},"lug_width":{"label":"The front lug's width across","kind":"length","measurements":[{"id":"round","value":0.532,"unit":"in","pm":0.08,"source":{"type":"derived","expr":"2 * ({.lug_bottom} - {.guide_rod_y})","via":"harvest"}}],"note":"The lug's lower end is a half round about the guide rod's axis: in the close right-front view (e546d93843c1) its front face's outline runs down its side and round under the rod's head into its bottom. As wide, then, as that round is across: twice the lug's bottom under the rod's axis."},"guide_rod_y":{"label":"The recoil spring's guide rod head, its centre below the bore axis","kind":"length","measurements":[{"id":"oblique","value":0.56,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/taurus-tx22-toro 7c0111a45816 (Sportsman's Warehouse 1883977-8: the T.O.R.O. from its right front and above, 1200 x 1200)","scaleRef":"the thread protector's front face (its rim an ellipse 90 px across and 145 px high: across, its 0.59 in silhouette, taurus-tx22-thread-protector.od)","method":"the head's centre (1045, 690) 208 px under the protector's front face's centre (1143, 482), at the vertical scale the protector's face gives (145 px for 0.59 in: 246 px/in), less the protector's face standing ahead of the lug's face (it reads lower by its distance along the bore times the view's slope): about 0.56","via":"harvest"}}]},"guide_rod_d":{"label":"The guide rod's head, across","kind":"length","measurements":[{"id":"oblique","value":0.3,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/taurus-tx22-toro 7c0111a45816 (Sportsman's Warehouse 1883977-8: the T.O.R.O. from its right front and above, 1200 x 1200)","scaleRef":"the thread protector's front face (its rim an ellipse 90 px across and 145 px high: across, its 0.59 in silhouette, taurus-tx22-thread-protector.od)","method":"the head's face 45 px across on row 690 at the protector's 90 px for 0.59 in","via":"harvest"}}]},"cut_rear_x":{"label":"The optic cut's rear wall","kind":"length","measurements":[{"id":"left","value":0.841,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/taurus-tx22-toro f0237849b397 (Sportsman's Warehouse 1883977-2: the T.O.R.O. from its left)","scaleRef":"the pin frame (158.8 px/in on the near face), shifted to the slide's frame","method":"the plate's rear end at column 1037 (profiles.side.features.cover_plate)","via":"harvest"}}],"note":"The cut runs across the slide's top, open at both sides: the cover plate's side face shows in it in both side views, from its front wall to its rear wall."},"cut_front_x":{"label":"The optic cut's front wall","kind":"length","measurements":[{"id":"left","value":2.504,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/taurus-tx22-toro f0237849b397 (Sportsman's Warehouse 1883977-2: the T.O.R.O. from its left)","scaleRef":"the pin frame (158.8 px/in on the near face), shifted to the slide's frame","method":"the plate's front end at column 774 (profiles.side.features.cover_plate)","via":"harvest"}}]},"cut_floor":{"label":"The optic cut's floor above the bore axis","kind":"length","measurements":[{"id":"left","value":0.44,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/taurus-tx22-toro f0237849b397 (Sportsman's Warehouse 1883977-2: the T.O.R.O. from its left)","scaleRef":"the pin frame (158.8 px/in on the near face), shifted to the slide's frame","method":"the plate's lower edge at row 229 from column 774 to 1037 (profiles.side.features.cover_plate; the darkest row under it, 232, is its shadow)","via":"harvest"}}],"note":"Where the plate's side face ends below: a dark line along it at rows 228 to 232 in the left view (its lower edge's shadow on the cut's floor), 0.08 to 0.09 under the slide's top."},"ramp1_rear_x":{"label":"The plate's first ramp's rear end (the step up to the second)","kind":"length","measurements":[{"id":"close","value":2.084,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/taurus-tx22-toro e36cac6c322c (Sportsman's Warehouse 1883977-6: close on the slide's rear top from its right, the muzzle at the right, 1200 x 1200)","scaleRef":"the plate's own ends at columns 552 and 1060, the left view's .cut_rear_x and .cut_front_x: 306.8 px/in along it","method":"the column where the lit wedge begins again at its full depth, 931 (between 928, thin, and 936, deep)","via":"harvest"}},{"id":"right","value":2.08,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/taurus-tx22-toro e50c634c3e4d (Sportsman's Warehouse 1883977-1: the T.O.R.O. from its right, the muzzle at the right)","scaleRef":"the plate's own ends at columns 153 and 413, the left view's .cut_rear_x and .cut_front_x: 157 px/in along it","method":"the step between columns 345 (thin) and 348 (deep)","via":"harvest"}}],"adopt":{"from":"close","reason":"The close view's step: the right view's agrees within its pixels."},"note":"The first ramp runs from the plate's front end (.cut_front_x) back to here. The left view's outline has the step too (profiles.side.features.cover_plate: 2.1 to 2.081)."},"ramp2_rear_x":{"label":"The plate's second ramp's rear end (the step up to the third)","kind":"length","measurements":[{"id":"close","value":1.709,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/taurus-tx22-toro e36cac6c322c (Sportsman's Warehouse 1883977-6: close on the slide's rear top from its right, the muzzle at the right, 1200 x 1200)","scaleRef":"the plate's own ends at columns 552 and 1060, the left view's .cut_rear_x and .cut_front_x: 306.8 px/in along it","method":"the step at column 816 (between 812, thin, and 820, deep)","via":"harvest"}},{"id":"right","value":1.717,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/taurus-tx22-toro e50c634c3e4d (Sportsman's Warehouse 1883977-1: the T.O.R.O. from its right, the muzzle at the right)","scaleRef":"the plate's own ends at columns 153 and 413, the left view's .cut_rear_x and .cut_front_x: 157 px/in along it","method":"the step between columns 288 (thin) and 291 (deep)","via":"harvest"}}],"adopt":{"from":"close","reason":"The close view's step: the right view's agrees within its pixels."},"note":"The left view's outline has the step at 1.72 to 1.701."},"ramp3_rear_x":{"label":"The plate's third ramp's rear end (where the flat under the screws' pad begins)","kind":"length","measurements":[{"id":"close","value":1.5,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/taurus-tx22-toro e36cac6c322c (Sportsman's Warehouse 1883977-6: close on the slide's rear top from its right, the muzzle at the right, 1200 x 1200)","scaleRef":"the plate's own ends at columns 552 and 1060, the left view's .cut_rear_x and .cut_front_x: 306.8 px/in along it","method":"the ramp's rear end at column 752, its step face lit (the flat behind it shows no lit band, 704 to 748)","via":"harvest"}},{"id":"right","value":1.507,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/taurus-tx22-toro e50c634c3e4d (Sportsman's Warehouse 1883977-1: the T.O.R.O. from its right, the muzzle at the right)","scaleRef":"the plate's own ends at columns 153 and 413, the left view's .cut_rear_x and .cut_front_x: 157 px/in along it","method":"the ramp's rear end between columns 255 (the flat, grey to its top) and 258 (the wedge)","via":"harvest"}}],"adopt":{"from":"close","reason":"The close view's step: the right view's agrees within its pixels."},"note":"Behind it the plate's top is a flat with no bevel, then the screws' round pad (the left view's bump, 1.379 to 1.17), whose side shows dark and curved in both right views."},"ramp4_front_x":{"label":"The plate's fourth ramp's front end (behind the screws' pad)","kind":"length","measurements":[{"id":"close","value":1.168,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/taurus-tx22-toro e36cac6c322c (Sportsman's Warehouse 1883977-6: close on the slide's rear top from its right, the muzzle at the right, 1200 x 1200)","scaleRef":"the plate's own ends at columns 552 and 1060, the left view's .cut_rear_x and .cut_front_x: 306.8 px/in along it","method":"where the pad's dark side gives way to the wedge, column 650","via":"harvest"}},{"id":"right","value":1.166,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/taurus-tx22-toro e50c634c3e4d (Sportsman's Warehouse 1883977-1: the T.O.R.O. from its right, the muzzle at the right)","scaleRef":"the plate's own ends at columns 153 and 413, the left view's .cut_rear_x and .cut_front_x: 157 px/in along it","method":"the wedge's front end, column 203","via":"harvest"}}],"adopt":{"from":"close","reason":"The close view's step: the right view's agrees within its pixels."}},"ramp4_rear_x":{"label":"The plate's fourth ramp's rear end (the step up to the block at the plate's rear)","kind":"length","measurements":[{"id":"close","value":0.946,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/taurus-tx22-toro e36cac6c322c (Sportsman's Warehouse 1883977-6: close on the slide's rear top from its right, the muzzle at the right, 1200 x 1200)","scaleRef":"the plate's own ends at columns 552 and 1060, the left view's .cut_rear_x and .cut_front_x: 306.8 px/in along it","method":"the step between columns 580 (the block, no lit band) and 584 (the wedge at its deepest)","via":"harvest"}},{"id":"left","value":0.951,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/taurus-tx22-toro f0237849b397 (Sportsman's Warehouse 1883977-2: the T.O.R.O. from its left)","scaleRef":"the pin frame (158.8 px/in on the near face), shifted to the slide's frame","method":"the step in the plate's traced top, 0.961 to 0.942 (profiles.side.features.cover_plate), its middle","via":"harvest"}}],"adopt":{"from":"close","reason":"The close view's step; the left view's traced top has it too, within its pixel."},"note":"The right view (e50c634c3e4d) puts the step at column 172.5, 0.972, where the rear block's shade runs into the wedge: not taken."},"ramp1_bevel_front":{"label":"The first ramp's side bevel at its front end, its height on the side","kind":"length","measurements":[{"id":"close","value":0.016,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/taurus-tx22-toro e36cac6c322c (Sportsman's Warehouse 1883977-6: close on the slide's rear top from its right, the muzzle at the right, 1200 x 1200)","scaleRef":"306.8 px/in, the plate's own length (its ends at columns 552 and 1060)","method":"the lit band under the plate's top (grey 185 and over), its top and lower edge fitted along the ramp over 98 columns (rms 1.2 px) and read at its front end","via":"harvest"}},{"id":"right","value":0.014,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/taurus-tx22-toro e50c634c3e4d (Sportsman's Warehouse 1883977-1: the T.O.R.O. from its right, the muzzle at the right)","scaleRef":"157 px/in, the plate's own length (its ends at columns 153 and 413)","method":"the same over 51 columns (rms 0.7 px)","via":"harvest"}}],"adopt":{"from":"close","reason":"The close view's fit: twice the right view's pixels, and the two agree."}},"ramp1_bevel_rear":{"label":"The first ramp's side bevel at its rear end, its height on the side","kind":"length","measurements":[{"id":"close","value":0.053,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/taurus-tx22-toro e36cac6c322c (Sportsman's Warehouse 1883977-6: close on the slide's rear top from its right, the muzzle at the right, 1200 x 1200)","scaleRef":"306.8 px/in, the plate's own length (its ends at columns 552 and 1060)","method":"the lit band's fit (ramp1_bevel_front's) read at the ramp's rear end","via":"harvest"}},{"id":"right","value":0.047,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/taurus-tx22-toro e50c634c3e4d (Sportsman's Warehouse 1883977-1: the T.O.R.O. from its right, the muzzle at the right)","scaleRef":"157 px/in, the plate's own length (its ends at columns 153 and 413)","method":"the same at the ramp's rear end","via":"harvest"}}],"adopt":{"from":"close","reason":"The close view's fit: twice the right view's pixels, and the two agree."}},"ramp2_bevel_front":{"label":"The second ramp's side bevel at its front end, its height on the side","kind":"length","measurements":[{"id":"close","value":0.024,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/taurus-tx22-toro e36cac6c322c (Sportsman's Warehouse 1883977-6: close on the slide's rear top from its right, the muzzle at the right, 1200 x 1200)","scaleRef":"306.8 px/in, the plate's own length (its ends at columns 552 and 1060)","method":"the lit band's top and lower edge fitted along the ramp over 88 columns (rms 0.35 px), read at its front end","via":"harvest"}},{"id":"right","value":0.021,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/taurus-tx22-toro e50c634c3e4d (Sportsman's Warehouse 1883977-1: the T.O.R.O. from its right, the muzzle at the right)","scaleRef":"157 px/in, the plate's own length (its ends at columns 153 and 413)","method":"the same over 44 columns (rms 0.3 px)","via":"harvest"}}],"adopt":{"from":"close","reason":"The close view's fit: twice the right view's pixels, and the two agree."}},"ramp2_bevel_rear":{"label":"The second ramp's side bevel at its rear end, its height on the side","kind":"length","measurements":[{"id":"close","value":0.057,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/taurus-tx22-toro e36cac6c322c (Sportsman's Warehouse 1883977-6: close on the slide's rear top from its right, the muzzle at the right, 1200 x 1200)","scaleRef":"306.8 px/in, the plate's own length (its ends at columns 552 and 1060)","method":"the lit band's fit read at the ramp's rear end","via":"harvest"}},{"id":"right","value":0.057,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/taurus-tx22-toro e50c634c3e4d (Sportsman's Warehouse 1883977-1: the T.O.R.O. from its right, the muzzle at the right)","scaleRef":"157 px/in, the plate's own length (its ends at columns 153 and 413)","method":"the same at the ramp's rear end","via":"harvest"}}],"adopt":{"from":"close","reason":"The close view's fit: twice the right view's pixels, and the two agree."}},"ramp3_bevel_front":{"label":"The third ramp's side bevel at its front end, its height on the side","kind":"length","measurements":[{"id":"close","value":0.027,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/taurus-tx22-toro e36cac6c322c (Sportsman's Warehouse 1883977-6: close on the slide's rear top from its right, the muzzle at the right, 1200 x 1200)","scaleRef":"306.8 px/in, the plate's own length (its ends at columns 552 and 1060)","method":"the lit band's top and lower edge fitted along the ramp over 49 columns (rms 0.4 px), read at its front end","via":"harvest"}},{"id":"right","value":0.025,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/taurus-tx22-toro e50c634c3e4d (Sportsman's Warehouse 1883977-1: the T.O.R.O. from its right, the muzzle at the right)","scaleRef":"157 px/in, the plate's own length (its ends at columns 153 and 413)","method":"the same over 25 columns (rms 0.5 px)","via":"harvest"}}],"adopt":{"from":"close","reason":"The close view's fit: twice the right view's pixels, and the two agree."}},"ramp3_bevel_rear":{"label":"The third ramp's side bevel at its rear end, its height on the side","kind":"length","measurements":[{"id":"close","value":0.048,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/taurus-tx22-toro e36cac6c322c (Sportsman's Warehouse 1883977-6: close on the slide's rear top from its right, the muzzle at the right, 1200 x 1200)","scaleRef":"306.8 px/in, the plate's own length (its ends at columns 552 and 1060)","method":"the lit band's fit read at the ramp's rear end","via":"harvest"}},{"id":"right","value":0.049,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/taurus-tx22-toro e50c634c3e4d (Sportsman's Warehouse 1883977-1: the T.O.R.O. from its right, the muzzle at the right)","scaleRef":"157 px/in, the plate's own length (its ends at columns 153 and 413)","method":"the same at the ramp's rear end","via":"harvest"}}],"adopt":{"from":"close","reason":"The close view's fit: twice the right view's pixels, and the two agree."}},"ramp4_bevel_front":{"label":"The fourth ramp's side bevel at its front end, its height on the side","kind":"length","measurements":[{"id":"close","value":0.046,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/taurus-tx22-toro e36cac6c322c (Sportsman's Warehouse 1883977-6: close on the slide's rear top from its right, the muzzle at the right, 1200 x 1200)","scaleRef":"306.8 px/in, the plate's own length (its ends at columns 552 and 1060)","method":"the lit band's top and lower edge fitted along the ramp over 51 columns (rms 0.4 px), read at its front end","via":"harvest"}}],"note":"Read on the close view alone: in the right view the pad's dark side runs into this ramp's wedge, and the fit there leaves 2.8 px (0.058 at its front, 0.050 at its rear)."},"ramp4_bevel_rear":{"label":"The fourth ramp's side bevel at its rear end, its height on the side","kind":"length","measurements":[{"id":"close","value":0.065,"unit":"in","pm":0.005,"source":{"type":"photo","photo":"references/taurus-tx22-toro e36cac6c322c (Sportsman's Warehouse 1883977-6: close on the slide's rear top from its right, the muzzle at the right, 1200 x 1200)","scaleRef":"306.8 px/in, the plate's own length (its ends at columns 552 and 1060)","method":"the lit band's fit read at the ramp's rear end","via":"harvest"}}],"note":"The close view alone (ramp4_bevel_front's note)."},"floor_edge_break":{"label":"The break along the cut's floor where it meets each side face (the seam's lit line, under the plate's own break)","kind":"length","measurements":[{"id":"close","value":0.005,"unit":"in","pm":0.003,"source":{"type":"photo","photo":"references/taurus-tx22-toro e36cac6c322c (Sportsman's Warehouse 1883977-6: close on the slide's rear top from its right, the muzzle at the right, 1200 x 1200)","scaleRef":"306.8 px/in, the plate's own length (its ends at columns 552 and 1060)","method":"the lighter row or two under the dark run at the plate's foot (grey 185 and over against the side's 150 to 160), columns 752 to 1050","via":"harvest"}},{"id":"right","value":0.006,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/taurus-tx22-toro e50c634c3e4d (Sportsman's Warehouse 1883977-1: the T.O.R.O. from its right, the muzzle at the right)","scaleRef":"157 px/in, the plate's own length (its ends at columns 153 and 413)","method":"the one row under the dark one, 170 to 176 against the side's 150 (columns 291 to 345)","via":"harvest"}}],"adopt":{"from":"close","reason":"The close view: twice the right view's pixels, and the two agree."},"note":"Under the seam's dark line both right views have a line a little lighter than the side round it, a pixel or two: the floor's edge, broken and turned up to the light. Drawn between the cut's two walls and stopping just short of each (plate_edge_break is the dark half)."},"plate_edge_break":{"label":"The break along the plate's lower side edges and its ends' side edges (the seam's dark line)","kind":"length","measurements":[{"id":"close","value":0.0065,"unit":"in","pm":0.003,"source":{"type":"photo","photo":"references/taurus-tx22-toro e36cac6c322c (Sportsman's Warehouse 1883977-6: close on the slide's rear top from its right, the muzzle at the right, 1200 x 1200)","scaleRef":"306.8 px/in, the plate's own length (its ends at columns 552 and 1060)","method":"the dark run at the plate's foot (under half way from the side's grey to the darkest row), 2 px in the median of 150 columns (.cache/tx22/cut/seam.py in the batch's worktree)","via":"harvest"}}],"note":"The plate's foot shows as a dark line along the whole plate in both right views, and its two ends as dark lines from the floor to the top: its edges broken where they meet the slide. Drawn as a 45-degree break of this height on the plate (a face turned down and out, which the light leaves dark); the slide's own edge under it is broken too (floor_edge_break), the lit line under the dark one. Two pixels in the right view (e50c634c3e4d, 0.013) are its blur at half the close view's scale."},"screw_x":{"label":"The footprint's two screws, along the slide","kind":"length","measurements":[{"id":"left","value":1.278,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/taurus-tx22-toro f0237849b397 (Sportsman's Warehouse 1883977-2: the T.O.R.O. from its left)","scaleRef":"the pin frame (158.8 px/in on the near face), shifted to the slide's frame","method":"the near screw's head's bump on the plate's top, columns 958 to 978 (profiles.side.features.cover_screws, the first box)","via":"harvest"}}],"note":"The two screws stand side by side across the plate, not one behind the other: in the left-front oblique the far one's head is offset from the near one's purely across the plate (its centre 57 px along the plate's front edge's direction and none along the slide), so in the left view they are one bump on the plate's top. The other bump there, further back, is the plate's own raised rear block."},"screw_spacing":{"label":"The footprint's two screws, apart across the slide","kind":"length","measurements":[{"id":"oblique","value":0.42,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/taurus-tx22-toro d4f6e257c86f (Sportsman's Warehouse 1883977-7: the T.O.R.O. from its left front and above)","scaleRef":"the plate's top across, its front edge from its near corner (870, 290) to its far corner (780, 233): 106.5 px for the top flat inside the chamfers (.width less two .top_chamfer, 0.79)","method":"the two Torx heads' centres (998, 228) and (950, 197): 57 px apart along the front edge's direction and under a pixel along the slide, 0.537 of the plate's top","via":"harvest"}}]},"right_window_rear_x":{"label":"The right vent's rear end","kind":"length","measurements":[{"id":"right","value":4.46,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/taurus-tx22-toro e50c634c3e4d (Sportsman's Warehouse 1883977-1: the T.O.R.O. from its right, the muzzle at the right)","scaleRef":"the pin frame (rear 452.5, 382.5; front 664.5, 374.5: 157.2 px/in on the near face), its 0.9 degree roll against the pins' own line taken out, shifted to the slide's frame","method":"the vent's lit rim's rear end at column 721 (profiles.side check spec side-right, its feature right_window)","via":"harvest"}}],"note":"The right vent is shorter than the left: the ejection port is behind it on that side. Its height is the left vent's (the two rims' top and bottom edges at the same rows by eye, each side's photo)."},"right_window_front_x":{"label":"The right vent's front end","kind":"length","measurements":[{"id":"right","value":5.39,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/taurus-tx22-toro e50c634c3e4d (Sportsman's Warehouse 1883977-1: the T.O.R.O. from its right, the muzzle at the right)","scaleRef":"the pin frame (rear 452.5, 382.5; front 664.5, 374.5: 157.2 px/in on the near face), its 0.9 degree roll against the pins' own line taken out, shifted to the slide's frame","method":"the vent's lit rim's front end at column 868 (the check spec side-right, its feature right_window)","via":"harvest"}}]},"screw_hole_d":{"label":"The footprint's screw holes in the cut's floor, across","kind":"length","measurements":[{"id":"assumed","value":0.1,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the holes the cover plate's two screws go into (and a red dot's in its place), under the plate's heads; no view shows them.","via":"harvest"}}]},"front_dot_d":{"label":"The front sight's white dot, across","kind":"length","measurements":[{"id":"assumed","value":0.07,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the dot on the post's rear face, half the post's width; no photo looks at it.","via":"harvest"}}]},"rear_notch_depth":{"label":"The rear sight's notch, its depth","kind":"length","measurements":[{"id":"assumed","value":0.07,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the square notch between the sight's two ears in both obliques, about two fifths of the sight's height above the slide.","via":"harvest"}}]},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"model","value":4.53,"unit":"oz","pm":0.6,"source":{"type":"derived","basis":"The model's aluminium, the slide's body 2.6508 and the cover plate 0.144 cubic inches (pipeline/blender/taurus_tx22_toro_slide.py's manifests, volumes_in3), times std.density.aluminium (1.568 oz to the cubic inch: Gun Tests, \"SLIDE MATERIAL Aluminum\"; Taurus's manual, as the discovery read it, \"High Grade Aluminum\", which names no alloy: 6061's figure, 7075 4% over it): 4.382 oz; and its steel, the sights, the guide rod's head and the plate's screws, 0.0333 cubic inches times std.density.steel: 0.152 oz. The ± is the alloy's 4%, the width's ± 0.06 (6%), and what the slide is cut away inside that no view shows (the breech face, the striker's tunnel, the rails' grooves), which would make it lighter. app/tests/taurus-tx22-toro-slide.test.ts holds the models' volumes to it.","via":"harvest"}}],"note":"No page weighs the slide alone (Taurus sells it only in the conversion kit with its barrel and spring). Worked out from the model's aluminium."}}},{"subject":"toolcraft-556-bcg","title":"Toolcraft .223/5.56/300 BLK M16 Profile Bolt Carrier Group - Black Nitride (TOOAUTO-016)","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"ar15discounts","value":11.408,"unit":"oz","pm":0.0005,"stated":"Weight 11.408 oz","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, Toolcraft .223/5.56/300 BLK M16 Profile Bolt Carrier Group - Black Nitride (MPN TOOAUTO-016), Additional information","url":"https://ar15discounts.com/products/toolcraft-223-5-56-300blk-m16-profile-bolt-carrier-group-black-nitride/","retrieved":"2026-10-05","via":"harvest"}}],"note":"One figure: Dirty Bird Industries' page for the same product has the same row (\"Weight 11.408 oz\") in the same text, which names \"the AR15Discounts satisfaction guarantee\" and uses AR15Discounts' photos: a copy, not a second source. Right To Bear states none. No page says it was weighed."},"length":{"label":"The carrier's length","kind":"length","measurements":[{"id":"std","value":6.672,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.ar15.carrier_length}","via":"user"},"note":"US Army TDP drawing 8448507 (Carrier, Bolt): the tail's rear face to the front (bolt) face."}],"note":"The carrier is the standard's: its sellers call it \"Full Auto M16 Profile\" and \"mil-spec design\", and none states the carrier's size."},"od":{"label":"The carrier's diameter","kind":"length","measurements":[{"id":"std","value":0.994,"unit":"in","pm":0.0005,"source":{"type":"derived","expr":"{std.ar15.carrier_rail_od}","via":"user"},"note":"The diameter its rails are ground to (8448507); the body and the tail are .930 (std.ar15.carrier_body_od)."}],"note":"The carrier is the standard's: its sellers call it \"Full Auto M16 Profile\" and \"mil-spec design\", and none states the carrier's size."},"listed_length":{"label":"The longest of the three sizes a seller lists","kind":"length","measurements":[{"id":"ar15discounts","value":7.7,"unit":"in","pm":0.05,"stated":"Dimensions 7.7 × 1 × 1.4 in","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, Toolcraft .223/5.56/300 BLK M16 Profile Bolt Carrier Group - Black Nitride, Additional information","url":"https://ar15discounts.com/products/toolcraft-223-5-56-300blk-m16-profile-bolt-carrier-group-black-nitride/","retrieved":"2026-10-05","via":"harvest"}}],"note":"AR15Discounts' row doesn't say what its three numbers measure (the group, or its package); Dirty Bird's row for the same product is \"7.7 × 1.4 × 11.408 in\", the last its weight's number. Not used for anything drawn: the drawings' carrier with its bolt forward is 7.46 long."}}},{"subject":"unity-fast-micro-226","title":"Unity Tactical FAST Micro Mount, 2.26 in optical centerline","dimensions":{"optical_height":{"label":"The maker's optical centerline over the rail (2.26 in; given for no named dot)","kind":"length","measurements":[{"id":"launch","value":2.26,"unit":"in","pm":0.005,"stated":"The optical centerline of the mount is a nominal 2.26” above the rail.","source":{"type":"spec","publisher":"review","name":"Soldier Systems Daily, Unity Tactical announces FAST optics mounts (2019-01-19): the maker's launch text as printed there","url":"https://soldiersystems.net/2019/01/19/unity-tactical-announces-fast-optics-mounts/","retrieved":"2026-11-03","via":"harvest"}},{"id":"arisaka","value":2.26,"unit":"in","pm":0.005,"stated":"A 2.26” optical centerline height provides faster/easier reticle acquisition","source":{"type":"spec","publisher":"retailer","name":"Arisaka Defense, Unity FAST Micro Mount","url":"https://arisakadefense.com/unity-fast-micro-mount/","retrieved":"2026-11-03","via":"harvest"}},{"id":"primary-arms","value":2.26,"unit":"in","pm":0.005,"stated":"Mount Height 2.26 in.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Unity Tactical FAST - Aimpoint Micro Mount - Black (specifications)","url":"https://www.primaryarms.com/unity-tactical-fast-ap-micro-mount-black","retrieved":"2026-11-03","via":"harvest"}},{"id":"mile-high","value":2.26,"unit":"in","pm":0.005,"stated":"Height: 2.26\" to optical centerline","source":{"type":"spec","publisher":"retailer","name":"Mile High Shooting, Unity Tactical: FAST Micro, Red Dot Mount, 2.26\"","url":"https://www.milehighshooting.com/unity-tactical-fast-micro-red-dot-mount-2-26/","retrieved":"2026-11-03","via":"harvest"}}],"adopt":{"from":"launch","reason":"The maker's own launch text; three sellers repeat it. Primary Arms' FDE page has \"higher than other mounts at 2.2666”\" in its description, the same figure with a digit repeated."},"note":"\"Nominal\" in the maker's own words, and \"for most optics\" where a seller says what it is for; no page names the dot. Unity's \"Specs & Data\" graphic draws an Aimpoint Micro-shaped dot (side cap, front and rear caps) with the 2.26 in to its axis from the line the 1.42 in also starts at (the rail's top), and sellers sell it as \"designed for Aimpoint T1 red dot sights\" (Primary Arms). It is taken as the figure for an Aimpoint Micro T-1/T-2 (deck_above_rail says so)."},"deck_above_rail":{"label":"The deck's top (where the dot's base sits) above the rail's top","kind":"length","measurements":[{"id":"t-2","value":1.671,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.optical_height} - {aimpoint-micro-t-2.axis_above_base}","basis":"An assumption: that the maker's 2.26 in is the axis of an Aimpoint Micro T-1/T-2 on it. No page names the dot; the dot drawn on the maker's graphic is Micro-shaped and sellers sell the mount \"designed for Aimpoint T1 red dot sights\" (Primary Arms). A T-1 is taken to stand as a T-2 does (the ledger has only the T-2's axis over its base, 0.589 in).","via":"harvest"}},{"id":"graphic-axis","value":1.708,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/unity-fast-micro-226 7555942021c6 (Unity's \"FAST Micro Series Optic Mount Specs & Data\" graphic, as Big Tex Ordnance hosts it: FAST-Micro-Specs-510x394-1.jpg; its side view, the right side, with a dot on it)","scaleRef":"the maker's 2.26 in, drawn from the base line (the line the 1.42 in starts at, the rail's top) to the dot's axis: 112.5 px (450 px on a 4x enlargement), 49.8 px/in","method":"the base line (row 176.3 of the original) to the mount's top line, the seam under the dot's base (row 91.3): 85 px. The ± is a pixel at each line. The dot drawn on it then has its axis 0.55 in over its base","via":"harvest"}},{"id":"graphic-height","value":1.775,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/unity-fast-micro-226 7555942021c6 (the maker's graphic, its side and end views)","scaleRef":"the maker's 2.01 in (overall_height), drawn in the end view from the jaws' feet to the mount's top: 96.75 px of the original (387 on the 4x enlargement), 48.1 px/in","method":"the base line to the mount's top line in the side view (85 px) and in the end view (85 px), at the scale the 2.01 in sets; the same lines put the jaws' feet 0.235 in under the rail's top (clamp_below_rail)","via":"harvest"}},{"id":"end-photo","value":1.71,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/unity-fast-micro-226 1036ed689388 (TNVC, FAST-Micro-T2-front, 430 x 670: the black mount with a T-2 on it, on a short rail, end on from a little above)","scaleRef":"the maker's 2.01 in (overall_height) from the jaws' feet to the seam under the dot's base: 135 px (405 on a 3x enlargement), 67.2 px/in; the clamp across, 1.30 in (width), reads 1.317 at that scale","method":"the rail's top, where its head shows between the jaws (row 256.7), to the seam under the dot's base (row 141.7): 115 px. The ± is the rail's top, which the jaws hide but for its middle. The T-2's lens's middle is then 0.62 in over its base, against its own 0.589 ± 0.037","via":"harvest"}}],"adopt":{"from":"t-2","reason":"The maker's height is the figure that sets a dot's axis, and with it the T-2 (the dot sellers name it for) stands at 2.26 in. The graphic scaled by its own 2.26 in and TNVC's end photo agree with it within their ±. The graphic scaled by its 2.01 in disagrees by 0.10 in: the graphic's two vertical figures can't both be to its drawing (4% apart), and at that scale the dot drawn on it would stand at 2.35 in. Kept, and visible, because the photo of the right side has the cross bolts' axis 1.755 in under the deck's top, which with the deck adopted is 0.08 in under the rail's top (with the 2.01 scale's 1.775, at it, as Reptilia's are on theirs): what settles it is a measured review or the maker's drawing with the deck dimensioned."},"note":"No page gives it. Worked out from the maker's 2.26 in as a T-1/T-2's axis (an assumption, said in its basis), and read three ways on the maker's graphic and TNVC's end photo. The graphic's own figures don't agree with its drawing to better than 4% (its 2.26 in spans 450 px of its 4x enlargement, its 2.01 in 385 px, its 2.08 in 407 px across), so each reading names the figure it is scaled by."},"deck_x":{"label":"The footprint's middle along the deck, ahead of the clamp's middle","kind":"length","measurements":[{"id":"fde-above","value":0,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/unity-fast-micro-226 250d1c931401 (Rifle Supply's UTYFST-MICF_1_HR, 2000 x 2000: the FDE mount's right side, square on from a little above, its deck in view)","scaleRef":"the mount's length, mount_length = 2.08 in, over the silhouette's 1727 px (columns 144 to 1870): 830.3 px/in","method":"the recoil boss on the deck (its ends at columns 905 and 1083 on a crop of the top: its middle 994) against the middle between the two cross bolts' heads (their dark discs' centres of mass at -0.769 and +0.781 in from the silhouette's middle: 1007 + 830.3 x 0.006): 0.010 in behind, within the ± of the two pixels' readings","via":"harvest"}}],"note":"The recoil boss in the middle of the deck (in every view from above: the instruction sheet's drawings, the obliques) is what the dot's base is located by."},"mount_length":{"label":"Length along the rail","kind":"length","measurements":[{"id":"arisaka","value":2.08,"unit":"in","pm":0.005,"stated":"DIMENSIONS: 2.08″(L) x 1.30″(W) x 2.01″(H)","source":{"type":"spec","publisher":"retailer","name":"Arisaka Defense, Unity FAST Micro Mount","url":"https://arisakadefense.com/unity-fast-micro-mount/","retrieved":"2026-11-03","via":"harvest"}},{"id":"graphic","value":2.08,"unit":"in","pm":0.005,"stated":"2.08\" (the side view's length along its base)","source":{"type":"photo","photo":"references/unity-fast-micro-226 7555942021c6 (Unity's Specs & Data graphic: the figure as printed on it)","scaleRef":"none: the maker's printed figure","method":"the dimension written under the side view, between extension lines at the mount's two ends","via":"harvest"}},{"id":"tnvc","value":2,"unit":"in","stated":"Dimensions: 2 x 1.3 x 2 in","source":{"type":"spec","publisher":"retailer","name":"TNVC, Unity FAST Micro Mount (specs)","url":"https://tnvc.com/shop/unity-fast-micro-mount/","retrieved":"2026-11-03","via":"harvest"}},{"id":"mile-high","value":2.2,"unit":"in","stated":"Dimensions (W X L X H): IN: < 1.4 X 2.2 X 2.1","source":{"type":"spec","publisher":"retailer","name":"Mile High Shooting, Unity Tactical: FAST Micro, Red Dot Mount, 2.26\"","url":"https://www.milehighshooting.com/unity-tactical-fast-micro-red-dot-mount-2-26/","retrieved":"2026-11-03","via":"harvest"}}],"adopt":{"from":"arisaka","reason":"The maker's own figure, printed on its graphic; TNVC's is it rounded, and Mile High's \"<\" figures are bounds."}},"width":{"label":"Width across the clamp (the rail-grabber's outer face to the bolts' band on the right)","kind":"length","measurements":[{"id":"arisaka","value":1.3,"unit":"in","pm":0.005,"stated":"DIMENSIONS: 2.08″(L) x 1.30″(W) x 2.01″(H)","source":{"type":"spec","publisher":"retailer","name":"Arisaka Defense, Unity FAST Micro Mount","url":"https://arisakadefense.com/unity-fast-micro-mount/","retrieved":"2026-11-03","via":"harvest"}},{"id":"tnvc","value":1.3,"unit":"in","stated":"Dimensions: 2 x 1.3 x 2 in","source":{"type":"spec","publisher":"retailer","name":"TNVC, Unity FAST Micro Mount (specs)","url":"https://tnvc.com/shop/unity-fast-micro-mount/","retrieved":"2026-11-03","via":"harvest"}}],"adopt":{"from":"arisaka","reason":"The maker's figure as its graphic prints it (\"1.30\"\" across the clamp in the end view); TNVC's is the same rounded."}},"overall_height":{"label":"Height from the jaws' feet to the deck's top","kind":"length","measurements":[{"id":"arisaka","value":2.01,"unit":"in","pm":0.005,"stated":"DIMENSIONS: 2.08″(L) x 1.30″(W) x 2.01″(H)","source":{"type":"spec","publisher":"retailer","name":"Arisaka Defense, Unity FAST Micro Mount","url":"https://arisakadefense.com/unity-fast-micro-mount/","retrieved":"2026-11-03","via":"harvest"}},{"id":"side-photo","value":2.03,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/unity-fast-micro-226 bbcff7c94073 (Primary Arms' FST-MICB_03.jpg, 2200 x 1467: the black mount's right side, square on from a hair above)","scaleRef":"mount_length = 2.08 in over the silhouette's 1301 px: 625.5 px/in","method":"rows 99 to 1368 at luminance 200; the top row is a sliver of the deck seen from above, a few hundredths","via":"harvest"}}],"adopt":{"from":"arisaka","reason":"The maker's figure, drawn on its graphic's end view from the jaws' feet to the mount's top; the side photo reads it 1% over, as a view from a little above does."}},"clamp_below_rail":{"label":"The jaws' feet under the rail's top","kind":"length","measurements":[{"id":"derived","value":0.339,"unit":"in","pm":0.04,"source":{"type":"derived","expr":"{.overall_height} - {.deck_above_rail}","via":"harvest"}},{"id":"graphic","value":0.235,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/unity-fast-micro-226 7555942021c6 (the maker's graphic, its side and end views)","scaleRef":"the maker's 2.01 in (overall_height) in the end view: 48.1 px/in","method":"the base line (the rail's top) to the jaws' feet: 11.25 px in the end view, 11.25 in the side view","via":"harvest"}}],"adopt":{"from":"derived","reason":"What the published overall height leaves under the deck adopted; the graphic's own drawing puts the feet 0.10 in higher, the same disagreement as deck_above_rail's, and kept with it."}},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"launch","value":3,"unit":"oz","pm":0.05,"stated":"Weighing in at 3.0 oz, the FAST Micro Mount competes with the lightest optic mount / rear BUIS combos","source":{"type":"spec","publisher":"review","name":"Soldier Systems Daily, Unity Tactical announces FAST optics mounts (2019-01-19): the maker's launch text","url":"https://soldiersystems.net/2019/01/19/unity-tactical-announces-fast-optics-mounts/","retrieved":"2026-11-03","via":"harvest"}},{"id":"arisaka","value":3,"unit":"oz","pm":0.05,"stated":"WEIGHT: 3.0 oz.","source":{"type":"spec","publisher":"retailer","name":"Arisaka Defense, Unity FAST Micro Mount","url":"https://arisakadefense.com/unity-fast-micro-mount/","retrieved":"2026-11-03","via":"harvest"}},{"id":"mile-high","value":3.5,"unit":"oz","stated":"Weight: Oz: <3.5 / G: <99.2","source":{"type":"spec","publisher":"retailer","name":"Mile High Shooting, Unity Tactical: FAST Micro, Red Dot Mount, 2.26\"","url":"https://www.milehighshooting.com/unity-tactical-fast-micro-red-dot-mount-2-26/","retrieved":"2026-11-03","via":"harvest"},"note":"A bound (\"<\"), not a weight."},{"id":"tnvc","value":0.2,"unit":"lb","stated":"Weight: 0.2lbs","source":{"type":"spec","publisher":"retailer","name":"TNVC, Unity FAST Micro Mount (specs)","url":"https://tnvc.com/shop/unity-fast-micro-mount/","retrieved":"2026-11-03","via":"harvest"}}],"adopt":{"from":"launch","reason":"The maker's figure (its launch text, and \"Weight 3.0 oz.\" on its own graphic); Arisaka repeats it. Mile High's is a bound, TNVC's a rounding to a tenth of a pound."},"note":"Big Tex's \"6 oz\" is its shipping weight."},"rear_sight_height":{"label":"The built-in rear sight's aperture above the rail's top","kind":"length","measurements":[{"id":"launch","value":1.42,"unit":"in","pm":0.005,"stated":"The mount features built-in, standard 1.42” height, windage-adjustable back up rear iron sight","source":{"type":"spec","publisher":"review","name":"Soldier Systems Daily, Unity Tactical announces FAST optics mounts (2019-01-19): the maker's launch text","url":"https://soldiersystems.net/2019/01/19/unity-tactical-announces-fast-optics-mounts/","retrieved":"2026-11-03","via":"harvest"}},{"id":"graphic","value":1.42,"unit":"in","pm":0.005,"stated":"1.42\" (in both views, from the base line to the rear aperture's middle)","source":{"type":"photo","photo":"references/unity-fast-micro-226 7555942021c6 (Unity's Specs & Data graphic: the figure as printed on it)","scaleRef":"none: the maker's printed figure","method":"the dimension beside the end view, from the base line to the middle of the ring in the upper window","via":"harvest"}}],"adopt":{"from":"launch","reason":"The maker's own sentence; its graphic prints the same."}},"sight_radius":{"label":"The built-in irons' sight radius (rear aperture to front post)","kind":"length","measurements":[{"id":"sheet","value":1.27,"unit":"in","pm":0.005,"stated":"Elevation adjustment for Front BUIS is 10 MOA per 1/8” turn (keep in mind this is a 1.27” Sight Radius.","source":{"type":"spec","publisher":"manufacturer","name":"Unity Tactical, FAST Micro Mount Installation Instructions (REV B, ©2020), page 3","url":"https://cdn.shopify.com/s/files/1/0253/9503/6263/files/Unity_Tactical_FAST_Micro_Mount_Instructions.pdf","retrieved":"2026-11-03","via":"harvest"}}]},"rear_sight_x":{"label":"The rear sight (its windage drum's axis) ahead of the clamp's middle","kind":"length","measurements":[{"id":"fde","value":-0.353,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/unity-fast-micro-226 52f6e3ffa50f (Primary Arms' FST-MICF_03.jpg, 2200 x 1467: the FDE mount's right side, square on)","scaleRef":"mount_length = 2.08 in over the silhouette's 1292 px (columns 453 to 1744): 621.2 px/in","method":"the drum's dark disc, its centre of mass, from the silhouette's middle (the bolts' middle is 0.001 in from it)","via":"harvest"}},{"id":"black","value":-0.368,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/unity-fast-micro-226 bbcff7c94073 (Primary Arms' FST-MICB_03.jpg: the black mount's right side, square on)","scaleRef":"mount_length = 2.08 in over 1301 px: 625.5 px/in","method":"the drum's rim picked on a gridded enlargement (columns 775 to 975 of the original)","via":"harvest"}}],"adopt":{"from":"fde","reason":"A black drum on a tan face, found by its own pixels; the black photo's pick by eye on a black face is within its ±."},"note":"The drum turns the aperture across (\"Windage adjustment of Rear BUIS ... can be made with Aimpoint adjustment tools or flat blade screwdriver\"): the aperture is taken to be on the drum's axis, along the rifle."},"drum_below_top":{"label":"The windage drum's axis under the deck's top","kind":"length","measurements":[{"id":"fde","value":0.629,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/unity-fast-micro-226 52f6e3ffa50f (Primary Arms' FST-MICF_03.jpg: the FDE mount's right side, square on)","scaleRef":"621.2 px/in (mount_length); its height reads 2.022 in for the published 2.01","method":"the drum's dark disc, its centre of mass, 1.393 in over the jaws' feet; scaled by 2.01 / 2.022 to 1.381 in, and 2.01 less that","via":"harvest"}}]},"drum_d":{"label":"The windage drum's face, across","kind":"length","measurements":[{"id":"black","value":0.32,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/unity-fast-micro-226 bbcff7c94073 (the black mount's right side, square on)","scaleRef":"625.5 px/in (mount_length)","method":"the drum's knurled rim, columns 775 to 975 on a gridded enlargement: 200 px","via":"harvest"}}]},"drum_relief_d":{"label":"The round relief the drum sits in, across","kind":"length","measurements":[{"id":"black","value":0.46,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/unity-fast-micro-226 bbcff7c94073 (the black mount's right side, square on)","scaleRef":"625.5 px/in (mount_length)","method":"the relief's arc over the drum, columns 730 to 1020 on a gridded enlargement, taken as a circle about the drum's axis","via":"harvest"}}]},"relief_depth":{"label":"How deep the drum's relief and the side pockets are cut","kind":"length","measurements":[{"id":"assumed","value":0.025,"unit":"in","pm":0.015,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows a pocket or the drum's relief in section; the obliques show each as a shallow step with its edge lit.","via":"harvest"}}]},"cross_bolt_spacing":{"label":"The two cross bolts apart","kind":"length","measurements":[{"id":"fde","value":1.584,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/unity-fast-micro-226 52f6e3ffa50f (Primary Arms' FST-MICF_03.jpg: the FDE mount's right side, square on)","scaleRef":"621.2 px/in (mount_length)","method":"the two bolts' heads' dark discs, their centres of mass: -0.791 and +0.793 in from the silhouette's middle","via":"harvest"}},{"id":"fde-above","value":1.55,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/unity-fast-micro-226 250d1c931401 (Rifle Supply's FDE right side, from a little above)","scaleRef":"830.3 px/in (mount_length)","method":"the heads' dark discs' centres of mass, -0.769 and +0.781 in; the left one's disc runs into its counterbore's shadow","via":"harvest"}},{"id":"black","value":1.566,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/unity-fast-micro-226 bbcff7c94073 (the black mount's right side, square on)","scaleRef":"625.5 px/in (mount_length)","method":"the heads' rims picked on a gridded enlargement","via":"harvest"}}],"adopt":{"from":"fde","reason":"The square view with black heads on a tan face; four slots of the rail apart, as the bolts lie in its slots."},"note":"Four of the rail's slots apart (4 x 0.394 = 1.576 in), within the readings' ±."},"bolt_above_feet":{"label":"The cross bolts' axis over the jaws' feet","kind":"length","measurements":[{"id":"fde","value":0.255,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/unity-fast-micro-226 52f6e3ffa50f (the FDE mount's right side, square on)","scaleRef":"621.2 px/in (mount_length)","method":"the two heads' discs' centres of mass, 0.247 and 0.266 in over the jaws' feet (row 1361)","via":"harvest"}}]},"bolt_head_d":{"label":"A cross bolt's head, across","kind":"length","measurements":[{"id":"black","value":0.27,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/unity-fast-micro-226 bbcff7c94073 (the black mount's right side, square on)","scaleRef":"625.5 px/in (mount_length)","method":"the head's rim inside its counterbore, on a gridded enlargement (about 170 px)","via":"harvest"}}]},"bolt_counterbore_d":{"label":"The counterbore each head sits in, across","kind":"length","measurements":[{"id":"fde","value":0.34,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/unity-fast-micro-226 52f6e3ffa50f (the FDE mount's right side, square on)","scaleRef":"621.2 px/in (mount_length)","method":"the dark disc of each head and its counterbore's shadow, 0.338 and 0.341 in across","via":"harvest"}}]},"lever_hole_d":{"label":"The round hole between the bolts (where a QD lever's shaft goes), across","kind":"length","measurements":[{"id":"fde","value":0.24,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/unity-fast-micro-226 52f6e3ffa50f (the FDE mount's right side, square on)","scaleRef":"621.2 px/in (mount_length)","method":"its dark disc, 0.241 in across, centred 0.003 in behind the silhouette's middle and 0.244 in over the jaws' feet","via":"harvest"}}]},"lever_recess_af":{"label":"The octagonal recess round that hole, across its flats","kind":"length","measurements":[{"id":"black","value":0.39,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/unity-fast-micro-226 bbcff7c94073 (the black mount's right side, square on)","scaleRef":"625.5 px/in (mount_length)","method":"its two upright flats, columns 975 to 1220 of the original on a gridded enlargement","via":"harvest"}}]},"small_hole_spacing":{"label":"The two small holes either side of the octagonal recess, apart","kind":"length","measurements":[{"id":"fde","value":0.612,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/unity-fast-micro-226 52f6e3ffa50f (the FDE mount's right side, square on)","scaleRef":"621.2 px/in (mount_length)","method":"their dark discs' centres, -0.298 and +0.314 in from the silhouette's middle, 0.30 in over the jaws' feet","via":"harvest"}}]},"small_hole_above_feet":{"label":"Those small holes' middles over the jaws' feet","kind":"length","measurements":[{"id":"fde","value":0.305,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/unity-fast-micro-226 52f6e3ffa50f (the FDE mount's right side, square on)","scaleRef":"621.2 px/in (mount_length)","method":"their dark discs' centres of mass, 0.309 and 0.300 in over the jaws' feet (row 1361)","via":"harvest"}}]},"small_hole_d":{"label":"Those small holes, across","kind":"length","measurements":[{"id":"fde","value":0.108,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/unity-fast-micro-226 52f6e3ffa50f (the FDE mount's right side, square on)","scaleRef":"621.2 px/in (mount_length)","method":"their dark discs, 0.108 in across each way","via":"harvest"}}]},"band_below_top":{"label":"The step where the bolts' band stands out of the right face, under the deck's top","kind":"length","measurements":[{"id":"black","value":1.514,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/unity-fast-micro-226 bbcff7c94073 (the black mount's right side, square on)","scaleRef":"625.5 px/in (mount_length)","method":"the lit line across the face, row 1059 on a gridded enlargement: 0.496 in over the jaws' feet, 2.01 less that","via":"harvest"}}]},"top_width":{"label":"The body's width across at the deck","kind":"length","measurements":[{"id":"end-photo","value":0.91,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/unity-fast-micro-226 1036ed689388 (TNVC: the black mount with a T-2 on it, end on)","scaleRef":"width = 1.30 in across the clamp: 193.3 px on a 3x enlargement (580 px), 148.7 px per in there","method":"the mount's top under the dot's base, columns 390 to 795 on the enlargement: 405 px of 580","via":"harvest"}},{"id":"graphic","value":0.92,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/unity-fast-micro-226 7555942021c6 (the maker's graphic, its end view)","scaleRef":"width = 1.30 in across the clamp, 259 px on a 4x enlargement","method":"the mount's top line, 183 px","via":"harvest"}}],"adopt":{"from":"end-photo","reason":"A photograph, at three times the graphic's pixels; the two agree."}},"wall_width":{"label":"The body's width across its walls, under the deck's edge","kind":"length","measurements":[{"id":"end-photo","value":0.85,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/unity-fast-micro-226 1036ed689388 (TNVC: the black mount with a T-2 on it, end on)","scaleRef":"width = 1.30 in across the clamp (580 px on a 3x enlargement)","method":"the walls' outer faces between the deck and the band, columns about 405 to 780: 375 px","via":"harvest"}}]},"band_outer_z":{"label":"The bolts' band's outer face, out from the middle (the rifle's right)","kind":"length","measurements":[{"id":"end-photo","value":0.654,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/unity-fast-micro-226 1036ed689388 (TNVC: the black mount with a T-2 on it, end on)","scaleRef":"width = 1.30 in across the clamp (580 px on a 3x enlargement)","method":"the band's outer face (column 880) from the deck's middle (column 592.5): 287.5 px; the grabber's outer face is 292 px out the other side","via":"harvest"}}]},"grabber_top_below_top":{"label":"The rail-grabber bar's top, under the deck's top","kind":"length","measurements":[{"id":"end-photo","value":1.48,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/unity-fast-micro-226 1036ed689388 (TNVC: the black mount with a T-2 on it, end on)","scaleRef":"overall_height = 2.01 in, 405 px on a 3x enlargement","method":"the bar's top (row 720) under the dot's base (row 425)","via":"harvest"}}]},"grabber_bottom_below_top":{"label":"The rail-grabber bar's foot, under the deck's top","kind":"length","measurements":[{"id":"graphic","value":1.97,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/unity-fast-micro-226 7555942021c6 (the maker's graphic, its end view)","scaleRef":"overall_height = 2.01 in (387 px on a 4x enlargement)","method":"the bar's foot (row 745) under the mount's top (row 365)","via":"harvest"}}]},"grabber_length":{"label":"The rail-grabber bar, along the rail","kind":"length","measurements":[{"id":"assumed","value":1.9,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the bar shows only in obliques (the left side, Primary Arms' FST-MICB_02, c717fd0a3974), where it runs nearly the body's length with the two bolts' ends near its own; no square view of the left side is on file.","via":"harvest"}}]},"tunnel_top_below_top":{"label":"The sight tunnel (the oval window through the sides, the upper window through each end), its roof under the deck's top","kind":"length","measurements":[{"id":"black","value":0.171,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/unity-fast-micro-226 bbcff7c94073 (the black mount's right side, square on)","scaleRef":"625.5 px/in (mount_length)","method":"the oval window's see-through pixels (luminance over 200), rows 217 to 419: their top 1.839 in over the jaws' feet; 2.01 less that","via":"harvest"}}]},"tunnel_bottom_below_top":{"label":"The sight tunnel's floor under the deck's top","kind":"length","measurements":[{"id":"black","value":0.494,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/unity-fast-micro-226 bbcff7c94073 (the black mount's right side, square on)","scaleRef":"625.5 px/in (mount_length)","method":"the oval window's lowest see-through row, 1.516 in over the jaws' feet","via":"harvest"}}]},"oval_x0":{"label":"The oval window through the sides, its rear end ahead of the clamp's middle","kind":"length","measurements":[{"id":"black","value":-0.118,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/unity-fast-micro-226 bbcff7c94073 (the black mount's right side, square on)","scaleRef":"625.5 px/in (mount_length)","method":"the see-through pixels' rear end, column 1026, from the silhouette's middle","via":"harvest"}}]},"oval_x1":{"label":"The oval window's front end ahead of the clamp's middle","kind":"length","measurements":[{"id":"black","value":0.51,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/unity-fast-micro-226 bbcff7c94073 (the black mount's right side, square on)","scaleRef":"625.5 px/in (mount_length)","method":"the see-through pixels' front end, column 1418","via":"harvest"}}]},"tunnel_width":{"label":"The sight tunnel's width across (the end faces' upper windows)","kind":"length","measurements":[{"id":"end-photo","value":0.56,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/unity-fast-micro-226 1036ed689388 (TNVC: the black mount with a T-2 on it, end on)","scaleRef":"width = 1.30 in across the clamp (580 px on a 3x enlargement)","method":"the upper window's rim, columns 460 to 705: 245 px","via":"harvest"}}]},"window_x0":{"label":"The big window through the sides, its rear edge ahead of the clamp's middle","kind":"length","measurements":[{"id":"black","value":-0.499,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/unity-fast-micro-226 bbcff7c94073 (the black mount's right side, square on)","scaleRef":"625.5 px/in (mount_length)","method":"the see-through pixels, columns 788 to 1415","via":"harvest"}}]},"window_x1":{"label":"The big window's front edge ahead of the clamp's middle","kind":"length","measurements":[{"id":"black","value":0.505,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/unity-fast-micro-226 bbcff7c94073 (the black mount's right side, square on)","scaleRef":"625.5 px/in (mount_length)","method":"the see-through pixels' front edge, column 1415","via":"harvest"}}]},"window_top_below_top":{"label":"The big window's top edge under the deck's top","kind":"length","measurements":[{"id":"black","value":0.651,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/unity-fast-micro-226 bbcff7c94073 (the black mount's right side, square on)","scaleRef":"625.5 px/in (mount_length)","method":"the see-through pixels' top row, 519: 1.359 in over the jaws' feet","via":"harvest"}}]},"window_bottom_below_top":{"label":"The big window's bottom edge under the deck's top","kind":"length","measurements":[{"id":"black","value":1.45,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/unity-fast-micro-226 bbcff7c94073 (the black mount's right side, square on)","scaleRef":"625.5 px/in (mount_length)","method":"the see-through pixels' bottom row, 1019: 0.560 in over the jaws' feet","via":"harvest"}}]},"window_chamfer_x":{"label":"The big window's sloping upper rear edge, where it meets the top edge, ahead of the clamp's middle","kind":"length","measurements":[{"id":"black","value":-0.033,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/unity-fast-micro-226 bbcff7c94073 (the black mount's right side, square on)","scaleRef":"625.5 px/in (mount_length)","method":"on a gridded enlargement, where the slope's line meets the top edge's","via":"harvest"}}],"note":"The slope runs from here down to the rear edge at window_chamfer_below_top: 45 degrees within the readings."},"window_chamfer_below_top":{"label":"The big window's sloping edge, where it meets the rear edge, under the deck's top","kind":"length","measurements":[{"id":"black","value":1.147,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/unity-fast-micro-226 bbcff7c94073 (the black mount's right side, square on)","scaleRef":"625.5 px/in (mount_length)","method":"on a gridded enlargement, where the slope's line meets the rear edge's","via":"harvest"}}]},"window_corner_r":{"label":"The windows' and pockets' corners, their radius","kind":"length","measurements":[{"id":"black","value":0.08,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/unity-fast-micro-226 bbcff7c94073 (the black mount's right side, square on)","scaleRef":"625.5 px/in (mount_length)","method":"the big window's lower corners, on a gridded enlargement (about 50 px)","via":"harvest"}}]},"end_window_top_below_top":{"label":"The lower window through each end, its top under the deck's top","kind":"length","measurements":[{"id":"end-photo","value":0.77,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/unity-fast-micro-226 1036ed689388 (TNVC: the black mount with a T-2 on it, end on)","scaleRef":"overall_height = 2.01 in, 405 px on a 3x enlargement","method":"the lower window's rim, rows 580 to 700, under the dot's base (row 425)","via":"harvest"}}]},"end_window_bottom_below_top":{"label":"The lower window through each end, its bottom under the deck's top","kind":"length","measurements":[{"id":"end-photo","value":1.36,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/unity-fast-micro-226 1036ed689388 (TNVC: the black mount with a T-2 on it, end on)","scaleRef":"overall_height = 2.01 in, 405 px on a 3x enlargement","method":"the lower window's rim's bottom, row 700","via":"harvest"}}]},"end_window_width":{"label":"The lower window through each end, across","kind":"length","measurements":[{"id":"end-photo","value":0.57,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/unity-fast-micro-226 1036ed689388 (TNVC: the black mount with a T-2 on it, end on)","scaleRef":"width = 1.30 in across the clamp (580 px on a 3x enlargement)","method":"the lower window's rim, columns 455 to 705","via":"harvest"}}]},"rear_pocket_x0":{"label":"The rear side pocket's rear edge ahead of the clamp's middle","kind":"length","measurements":[{"id":"black","value":-0.896,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/unity-fast-micro-226 bbcff7c94073 (the black mount's right side, square on)","scaleRef":"625.5 px/in (mount_length)","method":"the pocket's lit rim on a gridded enlargement","via":"harvest"}}]},"rear_pocket_x1":{"label":"The rear side pocket's front edge (where it meets the drum's relief) ahead of the clamp's middle","kind":"length","measurements":[{"id":"black","value":-0.456,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/unity-fast-micro-226 bbcff7c94073 (the black mount's right side, square on)","scaleRef":"625.5 px/in (mount_length)","method":"the pocket's lit rim on a gridded enlargement; below the drum it follows the big window's slope, a web's width off it","via":"harvest"}}]},"front_pocket_x0":{"label":"The front side pocket's rear edge ahead of the clamp's middle","kind":"length","measurements":[{"id":"black","value":0.616,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/unity-fast-micro-226 bbcff7c94073 (the black mount's right side, square on)","scaleRef":"625.5 px/in (mount_length)","method":"the pocket's lit rim on a gridded enlargement","via":"harvest"}}]},"front_pocket_x1":{"label":"The front side pocket's front edge ahead of the clamp's middle","kind":"length","measurements":[{"id":"black","value":0.896,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/unity-fast-micro-226 bbcff7c94073 (the black mount's right side, square on)","scaleRef":"625.5 px/in (mount_length)","method":"the pocket's lit rim on a gridded enlargement","via":"harvest"}}]},"pocket_top_below_top":{"label":"The side pockets' top edges under the deck's top","kind":"length","measurements":[{"id":"black","value":0.615,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/unity-fast-micro-226 bbcff7c94073 (the black mount's right side, square on)","scaleRef":"625.5 px/in (mount_length)","method":"the two pockets' lit rims (0.619 and 0.611 under the top) on a gridded enlargement","via":"harvest"}}]},"pocket_bottom_below_top":{"label":"The side pockets' bottom edges under the deck's top","kind":"length","measurements":[{"id":"black","value":1.199,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/unity-fast-micro-226 bbcff7c94073 (the black mount's right side, square on)","scaleRef":"625.5 px/in (mount_length)","method":"the two pockets' lit rims (1.203 and 1.195 under the top) on a gridded enlargement","via":"harvest"}}]},"deck_rim_width":{"label":"Each of the two rims along the deck's edges, across (the dot's base stands on them)","kind":"length","measurements":[{"id":"oblique","value":0.09,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/unity-fast-micro-226 132598ee129a (Primary Arms' FST-MICF_02.jpg: the FDE mount from ahead, its left side and its deck from above, 2200 x 1467)","scaleRef":"the deck's own width, top_width = 0.91 in, across the oblique at the deck's front end","method":"by eye on a crop of the deck: each rim about a tenth of the deck's width; no view on file is square to the deck","via":"harvest"}}]},"deck_channel_depth":{"label":"How far the channel between the two rims is sunk under the deck's plane","kind":"length","measurements":[{"id":"assumed","value":0.05,"unit":"in","pm":0.03,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the rims' inner walls show in the obliques (132598ee129a, c717fd0a3974) at about half the deck slab's thickness, from above, where a height isn't read.","via":"harvest"}}]},"lug_length":{"label":"The recoil boss in the deck's middle, along the rail","kind":"length","measurements":[{"id":"fde-above","value":0.22,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/unity-fast-micro-226 250d1c931401 (Rifle Supply's UTYFST-MICF_1_HR: the FDE mount's right side from a little above, its deck in view)","scaleRef":"830.3 px/in (mount_length)","method":"the boss's two ends on a crop of the top, columns 905 and 1090","via":"harvest"}}]},"lug_width":{"label":"The recoil boss, across","kind":"length","measurements":[{"id":"oblique","value":0.3,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/unity-fast-micro-226 132598ee129a (Primary Arms' FST-MICF_02.jpg: the FDE mount from ahead, its left side and its deck from above, 2200 x 1467)","scaleRef":"its own length, lug_length = 0.22 in, beside it in the same plane","method":"by eye on a crop of the deck: about a third longer across than along","via":"harvest"}}]},"deck_opening_length":{"label":"Each of the two openings through the channel's floor (either side of the boss), along the rail","kind":"length","measurements":[{"id":"oblique","value":0.32,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/unity-fast-micro-226 132598ee129a (Primary Arms' FST-MICF_02.jpg: the FDE mount from ahead, its left side and its deck from above, 2200 x 1467)","scaleRef":"the boss's length (lug_length) beside them on the deck","method":"by eye on a crop of the deck: each opening about one and a half times the boss's length, a web as wide as a rim between it and the boss","via":"harvest"}}]},"deck_opening_width":{"label":"Those openings, across","kind":"length","measurements":[{"id":"oblique","value":0.42,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/unity-fast-micro-226 132598ee129a (Primary Arms' FST-MICF_02.jpg: the FDE mount from ahead, its left side and its deck from above, 2200 x 1467)","scaleRef":"the deck's width (top_width) at the same station","method":"by eye on a crop of the deck: each opening a little under half the deck's width, its ends round","via":"harvest"}}]},"edge_break":{"label":"The chamfer on the body's machined edges","kind":"length","measurements":[{"id":"black","value":0.011,"unit":"in","pm":0.004,"source":{"type":"photo","photo":"references/unity-fast-micro-226 bbcff7c94073 (the black mount's right side, square on)","scaleRef":"625.5 px/in (mount_length)","method":"the lit band along the right face's edges and the windows' rims, 6 to 8 px wide on a gridded enlargement","via":"harvest"}}]},"rear_aperture_d":{"label":"The rear sight's aperture ring, across (seen end on in the sight tunnel)","kind":"length","measurements":[{"id":"end-photo","value":0.2,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/unity-fast-micro-226 1036ed689388 (TNVC: the black mount with a T-2 on it, end on)","scaleRef":"width = 1.30 in across the clamp (580 px on a 3x enlargement)","method":"the ring inside the upper window, about 30 px across on the original","via":"harvest"}}]},"rear_aperture_hole_d":{"label":"The rear sight's peep hole, across","kind":"length","measurements":[{"id":"assumed","value":0.06,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the hole is a few pixels in the one end view on file.","via":"harvest"}}]},"rear_aperture_length":{"label":"The rear sight's aperture ring, along the rifle","kind":"length","measurements":[{"id":"assumed","value":0.12,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the ring is inside the body, and no view on file shows it from the side.","via":"harvest"}}]},"front_post_d":{"label":"The front sight post, across","kind":"length","measurements":[{"id":"assumed","value":0.06,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the post shows only in the instruction sheet's drawing (page 3), standing in the front end's upper window, about a third of the hex key's width beside it.","via":"harvest"}}]},"front_post_x":{"label":"The front sight post ahead of the clamp's middle","kind":"length","measurements":[{"id":"derived","value":0.917,"unit":"in","pm":0.012,"source":{"type":"derived","expr":"{.rear_sight_x} + {.sight_radius}","via":"harvest"}}]}}},{"subject":"vg6-gamma-556","title":"VG6 Precision GAMMA 556, APVG200001A (the second generation, sold by Aero Precision)","dimensions":{"overall_length":{"label":"Overall length (rear face to front face, the washer not included)","kind":"length","measurements":[{"id":"wing","value":1.83,"unit":"in","stated":"Length: 1.83\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, VG6 GAMMA 556 Muzzle Brake by VG6 Precision (MPN \"APVG200001A / APVG200010A\"; its own photographs of the second generation)","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/muzzle-devices/vg6-precision-gamma-556-muzzle-brake/","retrieved":"2026-10-28","via":"harvest"}},{"id":"at3","value":1.75,"unit":"in","stated":"Length: 1.75″","source":{"type":"spec","publisher":"retailer","name":"AT3 Tactical, VG6 Gamma 556 AR-15 Muzzle Device - 1/2x28 - 5.56 NATO (\"SKU: APVG200001A\")","url":"https://www.at3tactical.com/products/vg6-precision-gamma-556-muzzle-brake","retrieved":"2026-10-28","via":"harvest"}},{"id":"ar15discounts","value":1.75,"unit":"in","stated":"Dimensions 1.75 × 0.86 × 0.86 in","source":{"type":"spec","publisher":"retailer","name":"AR15 Discounts, VG6 GAMMA 556 - APVG200001A","url":"https://ar15discounts.com/products/vg6-gamma-556/","retrieved":"2026-10-28","via":"harvest"}},{"id":"bearcreek","value":1.72,"unit":"in","stated":"Length: 1.72 in","source":{"type":"spec","publisher":"retailer","name":"Bear Creek Arsenal, VG6 GAMMA 556 Muzzle Brake (\"SKU APVG200001A\")","url":"https://www.bearcreekarsenal.com/vg6-gamma-556-muzzle.html","retrieved":"2026-10-28","via":"harvest"},"note":"Its \"Specifications for VG6 Precision VG6 Gamma Muzzle Device\" block. The same page's overview says \"Length 2.21\"\" (the next entry)."},{"id":"bearcreek_overview","value":2.21,"unit":"in","stated":"Length 2.21\"","source":{"type":"spec","publisher":"retailer","name":"Bear Creek Arsenal, VG6 GAMMA 556 Muzzle Brake (\"SKU APVG200001A\")","url":"https://www.bearcreekarsenal.com/vg6-gamma-556-muzzle.html","retrieved":"2026-10-28","via":"harvest"},"note":"The overview's list on the same page, beside \"Diameter 0.86\"\" and \"Weight 0.18\" (no unit). 2.57 times the diameter: no photo of the device is that long."},{"id":"photo","value":1.84,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/vg6-gamma-556 9a99cc0f47f2, 7da940867824, a79c5b9cdb86 (Aero's own gallery: the left side, the underside and the top, 1000 x 630), a935992d9bfd (Resilient Arms' top view, 450 x 820) and e392a62ddc82 (Primary Arms, APVG200001A_01: standing, from about 7 degrees above)","scaleRef":"the head's diameter in each, as od (0.86)","method":"the silhouette's length over its head's width at a level of 200 of 255: 2.139 to 2.16 on Aero's three and Resilient's; 2.25 on Primary Arms', less the front face's ellipse seen from above (70 px of 565 across: 7.1 degrees), 2.15. The ± spans them and the black edge's thinning on white (up to 3% of the width)","via":"harvest"}}],"adopt":{"from":"wing","reason":"The one seller whose figures are its own (its weight, diameter and bore are not the others' reprinted copy), and the length the maker's own photos and Primary Arms' give at the stated 0.86 diameter (1.84). 1.75 is the first generation's published length (Midwest Gun Works, APVG100001A), reprinted on second-generation pages with its weight; 1.72 and 2.21 are one page's two blocks."}},"washer_thickness":{"label":"Crush washer, thickness (between the barrel's shoulder and the device's rear face)","kind":"length","measurements":[{"id":"photo","value":0.105,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/vg6-gamma-556 e392a62ddc82 (Primary Arms, APVG200001A_01: the device standing and its crush washer lying beside it, from about 7 to 16 degrees above, 2200 x 1467)","scaleRef":"the device's head in the same photo, 565 px across, as od (0.86)","method":"the washer's silhouette row by row at a level of 200 of 255: its widest run (478 px) is its outside diameter; the rows at that width (66 px) are its outer face seen nearly side on, its height over the cosine of the view's angle (16 degrees, from its top ellipse: 134 px for 478 across)","via":"harvest"}}],"note":"\"Includes crush washer\" (Primary Arms; Aero's sellers the same). As read uncrushed in a photo: a crush washer is flattened some way as the device is timed, by an amount no source states, and the ± takes that in."},"length":{"label":"Length ahead of the barrel's shoulder, installed (to the front face; the crush washer's thickness included)","kind":"length","measurements":[{"id":"stack","value":1.935,"unit":"in","source":{"type":"derived","expr":"{.washer_thickness} + {.overall_length}","via":"harvest"},"note":"The washer against the shoulder, the device against the washer."}]},"od":{"label":"Largest outside diameter (the head, and the rear section between its flats)","kind":"length","measurements":[{"id":"at3","value":0.86,"unit":"in","stated":"Diameter: .86″","source":{"type":"spec","publisher":"retailer","name":"AT3 Tactical, VG6 Gamma 556 AR-15 Muzzle Device - 1/2x28 - 5.56 NATO (\"SKU: APVG200001A\")","url":"https://www.at3tactical.com/products/vg6-precision-gamma-556-muzzle-brake","retrieved":"2026-10-28","via":"harvest"}},{"id":"ar15discounts","value":0.86,"unit":"in","stated":"Dimensions 1.75 × 0.86 × 0.86 in","source":{"type":"spec","publisher":"retailer","name":"AR15 Discounts, VG6 GAMMA 556 - APVG200001A","url":"https://ar15discounts.com/products/vg6-gamma-556/","retrieved":"2026-10-28","via":"harvest"}},{"id":"bearcreek","value":0.86,"unit":"in","stated":"Diameter 0.86\"","source":{"type":"spec","publisher":"retailer","name":"Bear Creek Arsenal, VG6 GAMMA 556 Muzzle Brake (\"SKU APVG200001A\")","url":"https://www.bearcreekarsenal.com/vg6-gamma-556-muzzle.html","retrieved":"2026-10-28","via":"harvest"}},{"id":"wing","value":0.865,"unit":"in","stated":"Outer Diameter: 0.865\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, VG6 GAMMA 556 Muzzle Brake by VG6 Precision (MPN \"APVG200001A / APVG200010A\"; its own photographs of the second generation)","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/muzzle-devices/vg6-precision-gamma-556-muzzle-brake/","retrieved":"2026-10-28","via":"harvest"}}],"adopt":{"from":"at3","reason":"Three sellers state .86; Wing Tactical's .865 is within its last digit. The photos read the side view's width the same from the front face to the rear one: one diameter, the rear section's narrower look from above being its flats."}},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"wing","value":2.22,"unit":"oz","stated":"Weight: 2.22 oz.","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, VG6 GAMMA 556 Muzzle Brake by VG6 Precision (MPN \"APVG200001A / APVG200010A\"; its own photographs of the second generation)","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/muzzle-devices/vg6-precision-gamma-556-muzzle-brake/","retrieved":"2026-10-28","via":"harvest"}},{"id":"at3","value":2.1,"unit":"oz","stated":"Weight: 2.1 oz","source":{"type":"spec","publisher":"retailer","name":"AT3 Tactical, VG6 Gamma 556 AR-15 Muzzle Device - 1/2x28 - 5.56 NATO (\"SKU: APVG200001A\")","url":"https://www.at3tactical.com/products/vg6-precision-gamma-556-muzzle-brake","retrieved":"2026-10-28","via":"harvest"}},{"id":"riflesupply","value":2.1,"unit":"oz","stated":"Weight: 2.1oz","source":{"type":"spec","publisher":"retailer","name":"Rifle Supply, VG6 Gamma 556 | Muzzle Device | 5.56 NATO | Black | APVG200001A","url":"https://riflesupply.com/VG6-Gamma-556-Muzzle-Device-556-NATO-Black-APVG200001A_p_3557.html","retrieved":"2026-10-28","via":"harvest"}},{"id":"aerospacearms","value":2.1,"unit":"oz","stated":"Weight: 2.1oz","source":{"type":"spec","publisher":"retailer","name":"Aerospace Arms, Aero Precision VG6 Gamma 556 (\"SKU: APVG200001A\")","url":"https://aerospacearms.com/aero-precision-vg6-gamma-556-muzzle-brake-223-rem-556nato-black-1-2x28/","retrieved":"2026-10-28","via":"harvest"}},{"id":"ar15discounts","value":2.08,"unit":"oz","stated":"Weight 2.08 oz","source":{"type":"spec","publisher":"retailer","name":"AR15 Discounts, VG6 GAMMA 556 - APVG200001A","url":"https://ar15discounts.com/products/vg6-gamma-556/","retrieved":"2026-10-28","via":"harvest"},"note":"Its \"Additional information\" table; its description above it says \"Weight: 2.1oz\"."}],"adopt":{"from":"wing","reason":"With its length: the one seller's figures that aren't the first generation's reprinted copy (Midwest Gun Works, APVG100001A: \"Weight: 2.1 oz.\"). The model's steel, at the density on file, is held to it in the part's test."}},"thread_length":{"label":"Barrel thread length it takes, or is made for","kind":"length","measurements":[],"note":"No page on file states how deep its threaded bore is, or what barrel thread it is made for: missing, and not given to the interface."},"thread_depth":{"label":"Threaded bore's depth from the rear face (as drawn)","kind":"length","measurements":[{"id":"assumed","value":0.6,"unit":"in","pm":0.1,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows the threaded bore's depth. It is drawn stopping short of the rear port, which begins 0.75 in ahead of the rear face, and it shows only from behind.","via":"harvest"}}]},"bore_d":{"label":"Bore through the baffles and the front face, diameter","kind":"length","measurements":[{"id":"wing","value":0.27,"unit":"in","stated":"Bore Diameter: 0.27\"","source":{"type":"spec","publisher":"retailer","name":"Wing Tactical, VG6 GAMMA 556 Muzzle Brake by VG6 Precision (MPN \"APVG200001A / APVG200010A\"; its own photographs of the second generation)","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/muzzle-devices/vg6-precision-gamma-556-muzzle-brake/","retrieved":"2026-10-28","via":"harvest"}}]},"front_chamfer":{"label":"Front face's edge chamfer","kind":"length","measurements":[{"id":"photo","value":0.02,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/vg6-gamma-556 29ecb6b81ea4 (Wing Tactical's three straight views of APVG200001A side by side, muzzle up, 1280 x 1280: the middle one, the left side, the ports to the lens, its top at the right edge)","scaleRef":"along the device, its own length, 667 px (rows 308 to 975), as overall_length (1.83): 364.5 px/in; across, its own width, 298 px at the head and 301 at the rear section, as od (0.86): 347 to 350 px/in. The composite's length over its width (2.24) is 4.5% over every other photo of the device, so the two directions are scaled apart","method":"the silhouette and what shows through it, row by row at a level of 200 of 255 (scripts in .cache/batch15/vg6-gamma-556/); stations are where an edge's run changes, to a pixel or two (0.005 in along), widths are runs of backdrop between dark (± 2 px, 0.006 in across)","via":"harvest"},"note":"The width rolls off over 9 rows at the front face and over about as many at the rear; a corner that round is drawn as a 45-degree chamfer."}]},"rear_chamfer":{"label":"Rear face's edge chamfer","kind":"length","measurements":[{"id":"photo","value":0.02,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/vg6-gamma-556 29ecb6b81ea4 (Wing Tactical's three straight views of APVG200001A side by side, muzzle up, 1280 x 1280: the middle one, the left side, the ports to the lens, its top at the right edge)","scaleRef":"along the device, its own length, 667 px (rows 308 to 975), as overall_length (1.83): 364.5 px/in; across, its own width, 298 px at the head and 301 at the rear section, as od (0.86): 347 to 350 px/in. The composite's length over its width (2.24) is 4.5% over every other photo of the device, so the two directions are scaled apart","method":"the silhouette and what shows through it, row by row at a level of 200 of 255 (scripts in .cache/batch15/vg6-gamma-556/); stations are where an edge's run changes, to a pixel or two (0.005 in along), widths are runs of backdrop between dark (± 2 px, 0.006 in across)","via":"harvest"}}]},"front_port_rear_x":{"label":"Front side port, its rear edge (from the rear face)","kind":"length","measurements":[{"id":"photo","value":1.274,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/vg6-gamma-556 29ecb6b81ea4 (Wing Tactical's three straight views of APVG200001A side by side, muzzle up, 1280 x 1280: the middle one, the left side, the ports to the lens, its top at the right edge)","scaleRef":"along the device, its own length, 667 px (rows 308 to 975), as overall_length (1.83): 364.5 px/in; across, its own width, 298 px at the head and 301 at the rear section, as od (0.86): 347 to 350 px/in. The composite's length over its width (2.24) is 4.5% over every other photo of the device, so the two directions are scaled apart","method":"the silhouette and what shows through it, row by row at a level of 200 of 255 (scripts in .cache/batch15/vg6-gamma-556/); stations are where an edge's run changes, to a pixel or two (0.005 in along), widths are runs of backdrop between dark (± 2 px, 0.006 in across)","via":"harvest"},"note":"Rows 385 to 511 show backdrop through both side walls: 0.115 to 0.304 of the length from the front face. Aero's side view (9a99cc0f47f2): 0.114 to 0.300."}]},"front_port_front_x":{"label":"Front side port, its front edge (from the rear face)","kind":"length","measurements":[{"id":"photo","value":1.62,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/vg6-gamma-556 29ecb6b81ea4 (Wing Tactical's three straight views of APVG200001A side by side, muzzle up, 1280 x 1280: the middle one, the left side, the ports to the lens, its top at the right edge)","scaleRef":"along the device, its own length, 667 px (rows 308 to 975), as overall_length (1.83): 364.5 px/in; across, its own width, 298 px at the head and 301 at the rear section, as od (0.86): 347 to 350 px/in. The composite's length over its width (2.24) is 4.5% over every other photo of the device, so the two directions are scaled apart","method":"the silhouette and what shows through it, row by row at a level of 200 of 255 (scripts in .cache/batch15/vg6-gamma-556/); stations are where an edge's run changes, to a pixel or two (0.005 in along), widths are runs of backdrop between dark (± 2 px, 0.006 in across)","via":"harvest"}}]},"front_port_height":{"label":"Front side port, its height (through the device from side to side)","kind":"length","measurements":[{"id":"photo","value":0.577,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/vg6-gamma-556 29ecb6b81ea4 (Wing Tactical's three straight views of APVG200001A side by side, muzzle up, 1280 x 1280: the middle one, the left side, the ports to the lens, its top at the right edge)","scaleRef":"along the device, its own length, 667 px (rows 308 to 975), as overall_length (1.83): 364.5 px/in; across, its own width, 298 px at the head and 301 at the rear section, as od (0.86): 347 to 350 px/in. The composite's length over its width (2.24) is 4.5% over every other photo of the device, so the two directions are scaled apart","method":"the silhouette and what shows through it, row by row at a level of 200 of 255 (scripts in .cache/batch15/vg6-gamma-556/); stations are where an edge's run changes, to a pixel or two (0.005 in along), widths are runs of backdrop between dark (± 2 px, 0.006 in across)","via":"harvest"},"note":"200 px of backdrop between 298 of dark over the port's middle rows. Aero's side view: 101 of 150, 0.579. The top views' notch there (0.765 of the diameter across) would make it 0.555 for a square-sided through cut: the side views, square on the port, are taken."}]},"rear_port_rear_x":{"label":"Rear side port, its rear edge (from the rear face)","kind":"length","measurements":[{"id":"photo","value":0.754,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/vg6-gamma-556 29ecb6b81ea4 (Wing Tactical's three straight views of APVG200001A side by side, muzzle up, 1280 x 1280: the middle one, the left side, the ports to the lens, its top at the right edge)","scaleRef":"along the device, its own length, 667 px (rows 308 to 975), as overall_length (1.83): 364.5 px/in; across, its own width, 298 px at the head and 301 at the rear section, as od (0.86): 347 to 350 px/in. The composite's length over its width (2.24) is 4.5% over every other photo of the device, so the two directions are scaled apart","method":"the silhouette and what shows through it, row by row at a level of 200 of 255 (scripts in .cache/batch15/vg6-gamma-556/); stations are where an edge's run changes, to a pixel or two (0.005 in along), widths are runs of backdrop between dark (± 2 px, 0.006 in across)","via":"harvest"},"note":"Rows 556 to 700: 0.372 to 0.588 of the length from the front face. Aero's side view: 0.372 to 0.589."}]},"rear_port_front_x":{"label":"Rear side port, its front edge (from the rear face)","kind":"length","measurements":[{"id":"photo","value":1.149,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/vg6-gamma-556 29ecb6b81ea4 (Wing Tactical's three straight views of APVG200001A side by side, muzzle up, 1280 x 1280: the middle one, the left side, the ports to the lens, its top at the right edge)","scaleRef":"along the device, its own length, 667 px (rows 308 to 975), as overall_length (1.83): 364.5 px/in; across, its own width, 298 px at the head and 301 at the rear section, as od (0.86): 347 to 350 px/in. The composite's length over its width (2.24) is 4.5% over every other photo of the device, so the two directions are scaled apart","method":"the silhouette and what shows through it, row by row at a level of 200 of 255 (scripts in .cache/batch15/vg6-gamma-556/); stations are where an edge's run changes, to a pixel or two (0.005 in along), widths are runs of backdrop between dark (± 2 px, 0.006 in across)","via":"harvest"}}]},"rear_port_height":{"label":"Rear side port, its height","kind":"length","measurements":[{"id":"photo","value":0.631,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/vg6-gamma-556 29ecb6b81ea4 (Wing Tactical's three straight views of APVG200001A side by side, muzzle up, 1280 x 1280: the middle one, the left side, the ports to the lens, its top at the right edge)","scaleRef":"along the device, its own length, 667 px (rows 308 to 975), as overall_length (1.83): 364.5 px/in; across, its own width, 298 px at the head and 301 at the rear section, as od (0.86): 347 to 350 px/in. The composite's length over its width (2.24) is 4.5% over every other photo of the device, so the two directions are scaled apart","method":"the silhouette and what shows through it, row by row at a level of 200 of 255 (scripts in .cache/batch15/vg6-gamma-556/); stations are where an edge's run changes, to a pixel or two (0.005 in along), widths are runs of backdrop between dark (± 2 px, 0.006 in across)","via":"harvest"},"note":"220 px of backdrop between 300 of dark. Aero's side view reads 109 of 153, 0.613, and the top views' notch (0.71 of the diameter across) 0.608: the ± takes in all three."}]},"port_corner_r":{"label":"Side ports' corner radius (in the side view)","kind":"length","measurements":[{"id":"photo","value":0.09,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/vg6-gamma-556 29ecb6b81ea4 (Wing Tactical's three straight views of APVG200001A side by side, muzzle up, 1280 x 1280: the middle one, the left side, the ports to the lens, its top at the right edge)","scaleRef":"along the device, its own length, 667 px (rows 308 to 975), as overall_length (1.83): 364.5 px/in; across, its own width, 298 px at the head and 301 at the rear section, as od (0.86): 347 to 350 px/in. The composite's length over its width (2.24) is 4.5% over every other photo of the device, so the two directions are scaled apart","method":"the silhouette and what shows through it, row by row at a level of 200 of 255 (scripts in .cache/batch15/vg6-gamma-556/); stations are where an edge's run changes, to a pixel or two (0.005 in along), widths are runs of backdrop between dark (± 2 px, 0.006 in across)","via":"harvest"},"note":"The backdrop through each port grows to its full height over 33 rows (front) and 39 (rear) from the port's edge: 0.09 and 0.107 in."}]},"flats_across":{"label":"Wrench flats on the rear section, across (left and right sides)","kind":"length","measurements":[{"id":"photo","value":0.738,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/vg6-gamma-556 a935992d9bfd (Resilient Arms' picture of APVG200001A from above, muzzle up, the slot and the logo to the lens, 450 x 820)","scaleRef":"along the device, its own length, 770 px (rows 24 to 793), as overall_length (1.83): 420.8 px/in; across, the head's width, 360 px, as od (0.86): 418.6 px/in (the two within 0.5%)","method":"the silhouette row by row at a level of 200 of 255, and features inside it placed on a crop at 2.5 times size (± 3 px there, ± 0.003 in)","via":"harvest"},"note":"309 px of 360 from the rear port back to the rear face, but where the second groove cuts deeper: the rear section seen from above is narrower than the head by its flats, and the side views have it the head's width. Primary Arms' standing photo: 489 of 565 (0.744); Wing Tactical's top view 261 of 297 (0.756)."}]},"groove_1_rear_x":{"label":"Front groove, its rear edge (from the rear face)","kind":"length","measurements":[{"id":"photo","value":0.489,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/vg6-gamma-556 29ecb6b81ea4 (Wing Tactical's three straight views of APVG200001A side by side, muzzle up, 1280 x 1280: the middle one, the left side, the ports to the lens, its top at the right edge)","scaleRef":"along the device, its own length, 667 px (rows 308 to 975), as overall_length (1.83): 364.5 px/in; across, its own width, 298 px at the head and 301 at the rear section, as od (0.86): 347 to 350 px/in. The composite's length over its width (2.24) is 4.5% over every other photo of the device, so the two directions are scaled apart","method":"the silhouette and what shows through it, row by row at a level of 200 of 255 (scripts in .cache/batch15/vg6-gamma-556/); stations are where an edge's run changes, to a pixel or two (0.005 in along), widths are runs of backdrop between dark (± 2 px, 0.006 in across)","via":"harvest"},"note":"Its edges' middles at rows 748 and 797: 0.660 to 0.733 of the length from the front face. Aero's side view: 0.661 to 0.733."}]},"groove_1_front_x":{"label":"Front groove, its front edge (from the rear face)","kind":"length","measurements":[{"id":"photo","value":0.622,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/vg6-gamma-556 29ecb6b81ea4 (Wing Tactical's three straight views of APVG200001A side by side, muzzle up, 1280 x 1280: the middle one, the left side, the ports to the lens, its top at the right edge)","scaleRef":"along the device, its own length, 667 px (rows 308 to 975), as overall_length (1.83): 364.5 px/in; across, its own width, 298 px at the head and 301 at the rear section, as od (0.86): 347 to 350 px/in. The composite's length over its width (2.24) is 4.5% over every other photo of the device, so the two directions are scaled apart","method":"the silhouette and what shows through it, row by row at a level of 200 of 255 (scripts in .cache/batch15/vg6-gamma-556/); stations are where an edge's run changes, to a pixel or two (0.005 in along), widths are runs of backdrop between dark (± 2 px, 0.006 in across)","via":"harvest"}}]},"groove_1_d":{"label":"Front groove, diameter at its root","kind":"length","measurements":[{"id":"photo","value":0.786,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/vg6-gamma-556 29ecb6b81ea4 (Wing Tactical's three straight views of APVG200001A side by side, muzzle up, 1280 x 1280: the middle one, the left side, the ports to the lens, its top at the right edge)","scaleRef":"along the device, its own length, 667 px (rows 308 to 975), as overall_length (1.83): 364.5 px/in; across, its own width, 298 px at the head and 301 at the rear section, as od (0.86): 347 to 350 px/in. The composite's length over its width (2.24) is 4.5% over every other photo of the device, so the two directions are scaled apart","method":"the silhouette and what shows through it, row by row at a level of 200 of 255 (scripts in .cache/batch15/vg6-gamma-556/); stations are where an edge's run changes, to a pixel or two (0.005 in along), widths are runs of backdrop between dark (± 2 px, 0.006 in across)","via":"harvest"},"note":"275 px of 301. Aero's side view 139 of 153 (0.781). Larger than across the flats, so the flats run through it: from above it doesn't show in the outline."}]},"groove_2_rear_x":{"label":"Rear groove, its rear edge (from the rear face)","kind":"length","measurements":[{"id":"photo","value":0.258,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/vg6-gamma-556 29ecb6b81ea4 (Wing Tactical's three straight views of APVG200001A side by side, muzzle up, 1280 x 1280: the middle one, the left side, the ports to the lens, its top at the right edge)","scaleRef":"along the device, its own length, 667 px (rows 308 to 975), as overall_length (1.83): 364.5 px/in; across, its own width, 298 px at the head and 301 at the rear section, as od (0.86): 347 to 350 px/in. The composite's length over its width (2.24) is 4.5% over every other photo of the device, so the two directions are scaled apart","method":"the silhouette and what shows through it, row by row at a level of 200 of 255 (scripts in .cache/batch15/vg6-gamma-556/); stations are where an edge's run changes, to a pixel or two (0.005 in along), widths are runs of backdrop between dark (± 2 px, 0.006 in across)","via":"harvest"},"note":"Its edges' middles at rows 838 and 881: 0.795 to 0.859 of the length from the front face. Resilient's top view: 0.803 to 0.866."}]},"groove_2_front_x":{"label":"Rear groove, its front edge (from the rear face)","kind":"length","measurements":[{"id":"photo","value":0.375,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/vg6-gamma-556 29ecb6b81ea4 (Wing Tactical's three straight views of APVG200001A side by side, muzzle up, 1280 x 1280: the middle one, the left side, the ports to the lens, its top at the right edge)","scaleRef":"along the device, its own length, 667 px (rows 308 to 975), as overall_length (1.83): 364.5 px/in; across, its own width, 298 px at the head and 301 at the rear section, as od (0.86): 347 to 350 px/in. The composite's length over its width (2.24) is 4.5% over every other photo of the device, so the two directions are scaled apart","method":"the silhouette and what shows through it, row by row at a level of 200 of 255 (scripts in .cache/batch15/vg6-gamma-556/); stations are where an edge's run changes, to a pixel or two (0.005 in along), widths are runs of backdrop between dark (± 2 px, 0.006 in across)","via":"harvest"}}]},"groove_2_d":{"label":"Rear groove, diameter at its root","kind":"length","measurements":[{"id":"photo","value":0.703,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/vg6-gamma-556 29ecb6b81ea4 (Wing Tactical's three straight views of APVG200001A side by side, muzzle up, 1280 x 1280: the middle one, the left side, the ports to the lens, its top at the right edge)","scaleRef":"along the device, its own length, 667 px (rows 308 to 975), as overall_length (1.83): 364.5 px/in; across, its own width, 298 px at the head and 301 at the rear section, as od (0.86): 347 to 350 px/in. The composite's length over its width (2.24) is 4.5% over every other photo of the device, so the two directions are scaled apart","method":"the silhouette and what shows through it, row by row at a level of 200 of 255 (scripts in .cache/batch15/vg6-gamma-556/); stations are where an edge's run changes, to a pixel or two (0.005 in along), widths are runs of backdrop between dark (± 2 px, 0.006 in across)","via":"harvest"},"note":"246 px of 301. Aero's side view 125 of 153 (0.703); Resilient's top view 293 of 360 (0.700): under the flats, so it shows from above too."}]},"slot_width":{"label":"Top slot, width","kind":"length","measurements":[{"id":"photo","value":0.263,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/vg6-gamma-556 a935992d9bfd (Resilient Arms' picture of APVG200001A from above, muzzle up, the slot and the logo to the lens, 450 x 820)","scaleRef":"along the device, its own length, 770 px (rows 24 to 793), as overall_length (1.83): 420.8 px/in; across, the head's width, 360 px, as od (0.86): 418.6 px/in (the two within 0.5%)","method":"the silhouette row by row at a level of 200 of 255, and features inside it placed on a crop at 2.5 times size (± 3 px there, ± 0.003 in)","via":"harvest"},"note":"Its two walls' lit edges 110 px apart, of the head's 360; the dark between them 102 (0.244). Centred 6 px right of the silhouette's middle: the photo is rolled about 2 degrees."}]},"slot_length":{"label":"Top slot, from the front face to its rounded end","kind":"length","measurements":[{"id":"photo","value":0.718,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/vg6-gamma-556 a935992d9bfd (Resilient Arms' picture of APVG200001A from above, muzzle up, the slot and the logo to the lens, 450 x 820)","scaleRef":"along the device, its own length, 770 px (rows 24 to 793), as overall_length (1.83): 420.8 px/in; across, the head's width, 360 px, as od (0.86): 418.6 px/in (the two within 0.5%)","method":"the silhouette row by row at a level of 200 of 255, and features inside it placed on a crop at 2.5 times size (± 3 px there, ± 0.003 in)","via":"harvest"},"note":"Row 24 to row 326, the end's lit rim: over the front port and the web and into the rear port's length."}]},"slot_floor_y":{"label":"Top slot, its floor's height above the bore axis (as drawn)","kind":"length","measurements":[{"id":"assumed","value":0.11,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows the slot's floor. Primary Arms' photo from above shows the slot open into the front chamber and its end at the front face reaching the exit's upper lobe; it is drawn a little under the bore's top (0.135), so that it opens into the bore along its width through the web and the front ring, and into both chambers.","via":"harvest"}}]},"top_hole_d":{"label":"The small holes either side of the slot, diameter","kind":"length","measurements":[{"id":"photo","value":0.052,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/vg6-gamma-556 a935992d9bfd (Resilient Arms' picture of APVG200001A from above, muzzle up, the slot and the logo to the lens, 450 x 820)","scaleRef":"along the device, its own length, 770 px (rows 24 to 793), as overall_length (1.83): 420.8 px/in; across, the head's width, 360 px, as od (0.86): 418.6 px/in (the two within 0.5%)","method":"the silhouette row by row at a level of 200 of 255, and features inside it placed on a crop at 2.5 times size (± 3 px there, ± 0.003 in)","via":"harvest"},"note":"22 px along the device on the crop's scale. Three each side, in a triangle, counted on Resilient's, Wing Tactical's and Aero's top views and on Primary Arms' three photos."}]},"top_hole_1_x":{"label":"Small holes, the front one of each three (from the rear face)","kind":"length","measurements":[{"id":"photo","value":1.578,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/vg6-gamma-556 a935992d9bfd (Resilient Arms' picture of APVG200001A from above, muzzle up, the slot and the logo to the lens, 450 x 820)","scaleRef":"along the device, its own length, 770 px (rows 24 to 793), as overall_length (1.83): 420.8 px/in; across, the head's width, 360 px, as od (0.86): 418.6 px/in (the two within 0.5%)","method":"the silhouette row by row at a level of 200 of 255, and features inside it placed on a crop at 2.5 times size (± 3 px there, ± 0.003 in)","via":"harvest"},"note":"Centres at rows 130, 163 and 196 (front, middle, rear of each three), both sides."}]},"top_hole_2_x":{"label":"Small holes, the middle one of each three (from the rear face)","kind":"length","measurements":[{"id":"photo","value":1.5,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/vg6-gamma-556 a935992d9bfd (Resilient Arms' picture of APVG200001A from above, muzzle up, the slot and the logo to the lens, 450 x 820)","scaleRef":"along the device, its own length, 770 px (rows 24 to 793), as overall_length (1.83): 420.8 px/in; across, the head's width, 360 px, as od (0.86): 418.6 px/in (the two within 0.5%)","method":"the silhouette row by row at a level of 200 of 255, and features inside it placed on a crop at 2.5 times size (± 3 px there, ± 0.003 in)","via":"harvest"}}]},"top_hole_3_x":{"label":"Small holes, the rear one of each three (from the rear face)","kind":"length","measurements":[{"id":"photo","value":1.421,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/vg6-gamma-556 a935992d9bfd (Resilient Arms' picture of APVG200001A from above, muzzle up, the slot and the logo to the lens, 450 x 820)","scaleRef":"along the device, its own length, 770 px (rows 24 to 793), as overall_length (1.83): 420.8 px/in; across, the head's width, 360 px, as od (0.86): 418.6 px/in (the two within 0.5%)","method":"the silhouette row by row at a level of 200 of 255, and features inside it placed on a crop at 2.5 times size (± 3 px there, ± 0.003 in)","via":"harvest"}}]},"top_hole_outer_z":{"label":"Small holes, the front and rear of each three, off the slot's middle as seen from above","kind":"length","measurements":[{"id":"photo","value":0.272,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/vg6-gamma-556 a935992d9bfd (Resilient Arms' picture of APVG200001A from above, muzzle up, the slot and the logo to the lens, 450 x 820)","scaleRef":"along the device, its own length, 770 px (rows 24 to 793), as overall_length (1.83): 420.8 px/in; across, the head's width, 360 px, as od (0.86): 418.6 px/in (the two within 0.5%)","method":"the silhouette row by row at a level of 200 of 255, and features inside it placed on a crop at 2.5 times size (± 3 px there, ± 0.003 in)","via":"harvest"},"note":"115 and 113 px left and right of the slot's middle. On the round of the head that is 39 degrees off the top."}]},"top_hole_inner_z":{"label":"Small holes, the middle one of each three, off the slot's middle as seen from above","kind":"length","measurements":[{"id":"photo","value":0.215,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/vg6-gamma-556 a935992d9bfd (Resilient Arms' picture of APVG200001A from above, muzzle up, the slot and the logo to the lens, 450 x 820)","scaleRef":"along the device, its own length, 770 px (rows 24 to 793), as overall_length (1.83): 420.8 px/in; across, the head's width, 360 px, as od (0.86): 418.6 px/in (the two within 0.5%)","method":"the silhouette row by row at a level of 200 of 255, and features inside it placed on a crop at 2.5 times size (± 3 px there, ± 0.003 in)","via":"harvest"},"note":"91 and 89 px: 30 degrees off the top."}]},"bottom_slot_width":{"label":"Narrow slots under the chambers, width","kind":"length","measurements":[{"id":"photo","value":0.055,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/vg6-gamma-556 29ecb6b81ea4 (Wing Tactical's three straight views: the left one, the underside)","scaleRef":"along, its own length, 670 px, as overall_length (1.83); across, its head, 297 px, as od (0.86)","method":"slots placed by eye on a crop at 1.6 times size (± 3 px there, ± 0.005 in), the outline row by row at a level of 200 of 255","via":"harvest"},"note":"About 20 px of 297. Aero's underside view: 8.5 of 157 (0.047). Four under the front chamber, two under the rear, counted on both underside views and on Wing Tactical's photos from below the front."}]},"bottom_slot_front_rear_x":{"label":"The four slots under the front chamber, their rear ends (from the rear face)","kind":"length","measurements":[{"id":"photo","value":1.273,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/vg6-gamma-556 29ecb6b81ea4 (Wing Tactical's three straight views: the left one, the underside)","scaleRef":"along, its own length, 670 px, as overall_length (1.83); across, its head, 297 px, as od (0.86)","method":"slots placed by eye on a crop at 1.6 times size (± 3 px there, ± 0.005 in), the outline row by row at a level of 200 of 255","via":"harvest"},"note":"0.121 to 0.304 of the length from the front face; Aero's underside: 0.121 to 0.305."}]},"bottom_slot_front_front_x":{"label":"The four slots under the front chamber, their front ends (from the rear face)","kind":"length","measurements":[{"id":"photo","value":1.608,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/vg6-gamma-556 29ecb6b81ea4 (Wing Tactical's three straight views: the left one, the underside)","scaleRef":"along, its own length, 670 px, as overall_length (1.83); across, its head, 297 px, as od (0.86)","method":"slots placed by eye on a crop at 1.6 times size (± 3 px there, ± 0.005 in), the outline row by row at a level of 200 of 255","via":"harvest"}}]},"bottom_slot_rear_rear_x":{"label":"The two slots under the rear chamber, their rear ends (from the rear face)","kind":"length","measurements":[{"id":"photo","value":0.76,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/vg6-gamma-556 29ecb6b81ea4 (Wing Tactical's three straight views: the left one, the underside)","scaleRef":"along, its own length, 670 px, as overall_length (1.83); across, its head, 297 px, as od (0.86)","method":"slots placed by eye on a crop at 1.6 times size (± 3 px there, ± 0.005 in), the outline row by row at a level of 200 of 255","via":"harvest"},"note":"0.379 to 0.585 of the length from the front face; Aero's underside: 0.372 to 0.593."}]},"bottom_slot_rear_front_x":{"label":"The two slots under the rear chamber, their front ends (from the rear face)","kind":"length","measurements":[{"id":"photo","value":1.136,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/vg6-gamma-556 29ecb6b81ea4 (Wing Tactical's three straight views: the left one, the underside)","scaleRef":"along, its own length, 670 px, as overall_length (1.83); across, its head, 297 px, as od (0.86)","method":"slots placed by eye on a crop at 1.6 times size (± 3 px there, ± 0.005 in), the outline row by row at a level of 200 of 255","via":"harvest"}}]},"bottom_slot_inner_z":{"label":"The front chamber's inner two slots, off the middle as seen from below","kind":"length","measurements":[{"id":"photo","value":0.133,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/vg6-gamma-556 29ecb6b81ea4 (Wing Tactical's three straight views: the left one, the underside)","scaleRef":"along, its own length, 670 px, as overall_length (1.83); across, its head, 297 px, as od (0.86)","method":"slots placed by eye on a crop at 1.6 times size (± 3 px there, ± 0.005 in), the outline row by row at a level of 200 of 255","via":"harvest"},"note":"45 and 47 px. Aero's underside: 0.123."}]},"bottom_slot_outer_z":{"label":"The front chamber's outer two slots, off the middle as seen from below","kind":"length","measurements":[{"id":"photo","value":0.272,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/vg6-gamma-556 29ecb6b81ea4 (Wing Tactical's three straight views: the left one, the underside)","scaleRef":"along, its own length, 670 px, as overall_length (1.83); across, its head, 297 px, as od (0.86)","method":"slots placed by eye on a crop at 1.6 times size (± 3 px there, ± 0.005 in), the outline row by row at a level of 200 of 255","via":"harvest"},"note":"92.5 and 95.5 px. Aero's underside: 0.266."}]},"bottom_slot_rear_z":{"label":"The rear chamber's two slots, off the middle as seen from below","kind":"length","measurements":[{"id":"photo","value":0.206,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/vg6-gamma-556 29ecb6b81ea4 (Wing Tactical's three straight views: the left one, the underside)","scaleRef":"along, its own length, 670 px, as overall_length (1.83); across, its head, 297 px, as od (0.86)","method":"slots placed by eye on a crop at 1.6 times size (± 3 px there, ± 0.005 in), the outline row by row at a level of 200 of 255","via":"harvest"},"note":"68.5 and 73.5 px. Aero's underside: 0.195."}]},"rear_hole_x":{"label":"Hole in the top of the rear section, its centre (from the rear face)","kind":"length","measurements":[{"id":"photo","value":0.119,"unit":"in","pm":0.008,"source":{"type":"photo","photo":"references/vg6-gamma-556 a935992d9bfd (Resilient Arms' picture of APVG200001A from above, muzzle up, the slot and the logo to the lens, 450 x 820)","scaleRef":"along the device, its own length, 770 px (rows 24 to 793), as overall_length (1.83): 420.8 px/in; across, the head's width, 360 px, as od (0.86): 418.6 px/in (the two within 0.5%)","method":"the silhouette row by row at a level of 200 of 255, and features inside it placed on a crop at 2.5 times size (± 3 px there, ± 0.003 in)","via":"harvest"},"note":"Its centre at row 744 of 24 to 793; one hole, on top (none in either underside view)."}]},"rear_hole_d":{"label":"Hole in the top of the rear section, diameter","kind":"length","measurements":[{"id":"photo","value":0.108,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/vg6-gamma-556 a935992d9bfd (Resilient Arms' picture of APVG200001A from above, muzzle up, the slot and the logo to the lens, 450 x 820)","scaleRef":"along the device, its own length, 770 px (rows 24 to 793), as overall_length (1.83): 420.8 px/in; across, the head's width, 360 px, as od (0.86): 418.6 px/in (the two within 0.5%)","method":"the silhouette row by row at a level of 200 of 255, and features inside it placed on a crop at 2.5 times size (± 3 px there, ± 0.003 in)","via":"harvest"},"note":"45 px of the head's 360."}]},"rear_hole_depth":{"label":"Hole in the top of the rear section, depth (as drawn)","kind":"length","measurements":[{"id":"assumed","value":0.12,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file looks into the hole. Drawn blind, ending short of the threaded bore.","via":"harvest"}}]},"lobe_reach":{"label":"Exit's three lobes, how far each reaches from the axis on the front face (as drawn)","kind":"length","measurements":[{"id":"assumed","value":0.2,"unit":"in","pm":0.05,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the exit is seen only obliquely (Primary Arms' APVG200001A_00, 7a565a7ca9cd), where three pointed lobes reach about halfway from the bore to the face's rim. Drawn at that.","via":"harvest"}}]},"lobe_depth":{"label":"Exit's three lobes, how far each runs back from the front face (as drawn)","kind":"length","measurements":[{"id":"assumed","value":0.12,"unit":"in","pm":0.06,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: in the oblique photo the lobes' walls run back into the front ring, which the front port opens behind 0.21 in from the face. Drawn a little over half that.","via":"harvest"}}]},"washer_od":{"label":"Crush washer, outside diameter","kind":"length","measurements":[{"id":"photo","value":0.728,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/vg6-gamma-556 e392a62ddc82 (Primary Arms, APVG200001A_01: the device standing and its crush washer lying beside it, from about 7 to 16 degrees above, 2200 x 1467)","scaleRef":"the device's head in the same photo, 565 px across, as od (0.86)","method":"the washer's silhouette row by row at a level of 200 of 255: its widest run (478 px) is its outside diameter; the rows at that width (66 px) are its outer face seen nearly side on, its height over the cosine of the view's angle (16 degrees, from its top ellipse: 134 px for 478 across)","via":"harvest"},"note":"478 px of the head's 565 in the same photo."}]},"washer_id":{"label":"Crush washer, inside diameter","kind":"length","measurements":[{"id":"photo","value":0.5,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/vg6-gamma-556 7a565a7ca9cd (Primary Arms, APVG200001A_00: the device and its crush washer lying beside it, 2200 x 1467)","scaleRef":"the washer's own outside diameter, as washer_od","method":"the washer's inside over its outside across the ellipse's long axis, 0.687 (about 230 of 335 px), by eye on the photo at 2000 px across","via":"harvest"},"note":"It goes over the 1/2-28 thread."}]},"thread_major_d":{"label":"The thread it is cut for: major diameter","kind":"length","measurements":[{"id":"tdp","value":0.4957,"unit":"in","pm":0.0033,"stated":"1/2-28 UNEF-2A MAJOR DIA .4989/.4924","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213","via":"user"}}],"note":"Its sellers: \"1/2x28 RH\" (Primary Arms), \"Thread: 1/2-28 RH\" (Rifle Supply). The Army barrel's 1/2-28, as the catalog's barrels are drawn."},"thread_minor_d":{"label":"The thread it is cut for: minor diameter","kind":"length","measurements":[{"id":"tdp","value":0.4551,"unit":"in","pm":0.002,"stated":"MINOR DIA .4551 MAX","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213","via":"user"}}]},"thread_pitch":{"label":"The thread it is cut for: pitch","kind":"length","measurements":[{"id":"tdp","value":0.03571,"unit":"in","pm":0.00005,"stated":"1/2-28 UNEF-2A","source":{"type":"standard","doc":"US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213","via":"user"}}]},"side_ports":{"label":"Large ports through each side (counted)","kind":"count","measurements":[{"id":"photo","value":2,"unit":"count","source":{"type":"photo","photo":"references/vg6-gamma-556 29ecb6b81ea4 (Wing Tactical's three straight views of APVG200001A side by side, muzzle up, 1280 x 1280: the middle one, the left side, the ports to the lens, its top at the right edge)","scaleRef":"along the device, its own length, 667 px (rows 308 to 975), as overall_length (1.83): 364.5 px/in; across, its own width, 298 px at the head and 301 at the rear section, as od (0.86): 347 to 350 px/in. The composite's length over its width (2.24) is 4.5% over every other photo of the device, so the two directions are scaled apart","method":"the silhouette and what shows through it, row by row at a level of 200 of 255 (scripts in .cache/batch15/vg6-gamma-556/); stations are where an edge's run changes, to a pixel or two (0.005 in along), widths are runs of backdrop between dark (± 2 px, 0.006 in across)","via":"harvest"},"note":"Two, a front and a rear, backdrop through both in the side views (Wing Tactical's, Aero's); two a side from above in every top view (the notches either side); Resilient Arms' title: \"2 Port Brake\"."}]},"top_holes":{"label":"Small holes either side of the top slot (counted, both sides)","kind":"count","measurements":[{"id":"photo","value":6,"unit":"count","source":{"type":"photo","photo":"references/vg6-gamma-556 a935992d9bfd (Resilient Arms' picture of APVG200001A from above, muzzle up, the slot and the logo to the lens, 450 x 820)","scaleRef":"along the device, its own length, 770 px (rows 24 to 793), as overall_length (1.83): 420.8 px/in; across, the head's width, 360 px, as od (0.86): 418.6 px/in (the two within 0.5%)","method":"the silhouette row by row at a level of 200 of 255, and features inside it placed on a crop at 2.5 times size (± 3 px there, ± 0.003 in)","via":"harvest"},"note":"Three a side in a triangle: Resilient Arms', Wing Tactical's and Aero's top views and Primary Arms' three photos all show three."}]},"bottom_slots":{"label":"Narrow slots underneath (counted)","kind":"count","measurements":[{"id":"photo","value":6,"unit":"count","source":{"type":"photo","photo":"references/vg6-gamma-556 29ecb6b81ea4 (Wing Tactical's three straight views: the left one, the underside)","scaleRef":"along, its own length, 670 px, as overall_length (1.83); across, its head, 297 px, as od (0.86)","method":"slots placed by eye on a crop at 1.6 times size (± 3 px there, ± 0.005 in), the outline row by row at a level of 200 of 255","via":"harvest"},"note":"Four under the front chamber, two under the rear: Wing Tactical's and Aero's underside views."}]}}},{"subject":"vltor-a5-buffer-spring","title":"VLTOR A5 Action Spring","dimensions":{"wire_d":{"label":"Wire diameter","kind":"length","measurements":[{"id":"std","value":0.072,"unit":"in","pm":0.001,"source":{"type":"derived","expr":"{std.carbine_action_spring.wire_d}","via":"harvest"},"note":"The Army's drawing of the rifle's action spring (8448629: \"WIRE DIA: .072±.001\"), which std.carbine_action_spring.wire_d is: VLTOR calls this spring \"A standard rifle action spring\"."}]},"od":{"label":"Outside diameter of its coils","kind":"length","measurements":[{"id":"std","value":0.94,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{std.carbine_action_spring.od}","via":"harvest"},"note":"The Army's drawing of the rifle's action spring (8448629: \".940 DIA±.015\"), which std.carbine_action_spring.od is."}]},"end_coil_od":{"label":"Outside diameter of the one reduced coil at each end","kind":"length","measurements":[{"id":"std","value":0.9,"unit":"in","pm":0.015,"source":{"type":"derived","expr":"{std.carbine_action_spring.end_coil_od}","via":"harvest"},"note":"The Army's drawing of the rifle's action spring (8448629: \".900 DIA±.015 REDUCE (1) COIL BOTH ENDS\")."}]},"coils":{"label":"Total coils","kind":"count","measurements":[{"id":"tdp","value":44,"unit":"count","stated":"TOTAL COILS: 44 REF","source":{"type":"standard","doc":"US Army TDP drawing 8448629 (Spring, Action: the RIFLE's), rev C, PDF page 36, spring data; user-supplied scan (references/…/Spec_Sheets/M16_Technical_Data_Package.pdf), crop .cache/buffer/std/p036-8448629-data.png","via":"user"},"note":"VLTOR: \"A standard rifle action spring\"; \"This rifle spring has the proper specs, including length, coil count, and wire diameter.\""},{"id":"photo","value":42,"unit":"count","pm":2,"source":{"type":"photo","photo":"references/vltor-a5-buffer-spring 15385186c4e5 (VLTOR's photograph of the A5 Action Spring alone, lying on the diagonal on white, 1068 x 708)","scaleRef":"none: a count","method":"the crests of the spring's outline along each side of its axis (the dark pixels' principal axis; .cache/batch15/vltor-a5-buffer-spring/crests.py, the batch-4 tool): 41 on one side and 42 on the other, 19 to 29 px apart. The closed coils at each end lie on the next, and a crest closer than 8 px to the last isn't counted: the ± is those end turns.","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The Army's drawing of the standard rifle spring, which VLTOR says this is; VLTOR's own photograph counts the same within its closed end turns."}},"free_length":{"label":"Free length","kind":"length","measurements":[{"id":"tdp","value":12.5,"unit":"in","pm":0.05,"stated":"12.50 FREE LENGTH AFTER SETTING, REF","source":{"type":"standard","doc":"US Army TDP drawing 8448629 (Spring, Action: the RIFLE's), rev C, PDF page 36, its view; user-supplied scan (references/…/Spec_Sheets/M16_Technical_Data_Package.pdf), crop .cache/buffer/std/p036-8448629-view.png","via":"user"},"note":"A reference figure on the drawing, read to its two places. VLTOR: \"Rifle-Length action spring for the A5 system.\""},{"id":"photo","value":12.46,"unit":"in","pm":0.6,"source":{"type":"photo","photo":"references/vltor-a5-buffer-spring 15385186c4e5 (VLTOR's photograph of the spring alone, lying on the diagonal)","scaleRef":"the spring's own outside diameter in the middle of its length, 77.5 px across its axis, as the Army's .940 (od): 82.4 px/in","method":"its length along its axis, 1027 px. The picture is taken from close by: the spring's width grows from 72 to 83 px from one end to the other, and read at either end the length is 11.6 or 13.3; the ± is half that spread.","via":"harvest"}}],"adopt":{"from":"tdp","reason":"The Army's drawing of the standard rifle spring, which VLTOR says this is; VLTOR's photograph agrees within its perspective."}},"solid_length":{"label":"Solid length (every coil on the next)","kind":"length","measurements":[{"id":"tdp","value":3.285,"unit":"in","stated":"SOLID LENGTH: 3.285 MAX","source":{"type":"standard","doc":"US Army TDP drawing 8448629 (Spring, Action: the RIFLE's), rev C, PDF page 36, spring data; user-supplied scan (references/…/Spec_Sheets/M16_Technical_Data_Package.pdf), crop .cache/buffer/std/p036-8448629-data.png","via":"user"},"note":"A check that the spring, round the A5 buffer in the RE-A5, isn't driven solid when the buffer reaches the tube's rear wall (app/tests/vltor-a5-buffer-spring.test.ts)."}]},"installed_length":{"label":"Its length as installed (the A5 buffer's seat to the RE-A5's rear wall, bolt forward)","kind":"length","measurements":[{"id":"room","value":7.66,"unit":"in","pm":0.05,"source":{"type":"derived","expr":"{vltor-a5-receiver-extension.tube_front_behind_pin} + {vltor-a5-receiver-extension.tube_length} - {vltor-a5-receiver-extension.rear_wall} + {std.ar15.upper_rear_face_x} - {std.carbine_buffer.head_thickness}","via":"harvest"}}],"note":"What the spring is drawn at, in the A5 tube: from the rear face of the A5H2's head (the standard head's thickness behind its front face, which rests at the upper receiver's rear face: the carrier's rear end, bolt forward) back to the rear wall inside the RE-A5. The rifle's own drawing gives its spring's mean assembled length in the rifle's tube as 8.190 (\"LOAD AT COMPRESSED LG OF 8.190 MEAN ASSEMBLED LENGTH= 5.8 LBS±.5 LBS\"): in the A5's shorter tube it is held half an inch shorter."},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"wire","value":2.23,"unit":"oz","pm":0.12,"source":{"type":"derived","expr":"3.14159265 * ({.od} - {.wire_d}) * {.coils} * 0.785398163 * {.wire_d} * {.wire_d} * {std.density.steel}","via":"harvest"}}],"note":"No maker's or seller's figure: VLTOR states none. Worked out from its wire: the wire's length round its coils times its section times what steel weighs. A derived figure, for the build's total; the ± is the coil count's, the wire's and the density's together."}}},{"subject":"vltor-a5-receiver-extension","title":"VLTOR RE-A5 7-Position Receiver Extension, MilSpec Diameter","dimensions":{"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"vltor","value":4.3,"unit":"oz","stated":"Weight 4.3 oz","source":{"type":"spec","publisher":"manufacturer","name":"VLTOR, RE-A5 7-Position Receiver Extension, MilSpec Diameter (SKU RE-A5), SPECIFICATIONS","url":"https://vltor.com/products/re-a5","retrieved":"2026-10-28","via":"harvest"}},{"id":"metal","value":4.29,"unit":"oz","pm":0.25,"source":{"type":"derived","expr":"(0.785398163 * ({.tube_od} * {.tube_od} - {std.receiver_extension.bore_d} * {std.receiver_extension.bore_d}) * {.tube_length} + 0.785398163 * {std.receiver_extension.bore_d} * {std.receiver_extension.bore_d} * {.rear_wall} + {std.receiver_extension.rail_width} * ({std.receiver_extension.rail_bottom_below_axis} - {.tube_od} / 2) * ({.tube_length} - {.rail_ramp_end} + 0.5 * ({.rail_ramp_end} - {.rail_ramp_start})) - {.channel_width} * {.channel_depth} * ({.channel_front_from_rear} - {.channel_rear_from_rear}) - 7 * 0.785398163 * {.position_hole_d} * {.position_hole_d} * ({std.receiver_extension.rail_bottom_below_axis} - {.tube_od} / 2 - {.channel_depth})) * {std.density.aluminium_7075}","via":"harvest"},"note":"A check of the model's sizes against VLTOR's weight, not a weight of its own."}],"adopt":{"from":"vltor","reason":"The maker's own figure for the tube. The metal worked out from the sizes drawn is within its ± of it (the thread's crests, the rail's lip and the fillets aren't in the formula)."},"note":"VLTOR's figure for the tube alone. The metal worked out from the sizes the model is drawn to, as 7075 (VLTOR: \"7075-T6 Aluminum\"), is beside it as a check: the tube's wall over its length, its rear wall, its rail behind the ramp and half the ramp, less the channel and the seven holes; the thread's crests, the rail's lip and the relief are left out of the formula, which the ± covers with the wall's and the channel's own."},"tube_od":{"label":"The tube's outside diameter","kind":"length","measurements":[{"id":"std","value":1.148,"unit":"in","source":{"type":"derived","expr":"{std.receiver_extension.milspec_od}","via":"harvest"},"note":"The standard mil-spec carbine tube's: VLTOR sells it as \"MilSpec Diameter\"."}],"note":"VLTOR names the tube \"RE-A5 7-Position Receiver Extension, MilSpec Diameter\" (its product page) and calls it \"a 7-position mil-spec receiver extension\" that \"accepts any standard mil-spec collapsible stock\" (https://vltor.com/a5); no page states a figure."},"tube_length":{"label":"The tube's length","kind":"length","measurements":[{"id":"vltor","value":7.9375,"unit":"in","pm":0.03125,"stated":"Length 7 15/16\"","source":{"type":"spec","publisher":"manufacturer","name":"VLTOR, RE-A5 7-Position Receiver Extension, MilSpec Diameter (SKU RE-A5), SPECIFICATIONS","url":"https://vltor.com/products/re-a5","retrieved":"2026-10-28","via":"harvest"},"note":"A sixteenths figure: a thirty-second either way."},{"id":"vltor-a5","value":7.9375,"unit":"in","pm":0.03125,"stated":"SKU RE-A5 Overall Length 7 15/16\"","source":{"type":"spec","publisher":"manufacturer","name":"VLTOR, A5 Buffer System page, its RE-A5 RECEIVER EXTENSION table","url":"https://vltor.com/a5","retrieved":"2026-10-28","via":"harvest"}}],"adopt":{"from":"vltor","reason":"The product page's own figure; the A5 page says the same and calls it the overall length."},"note":"VLTOR's A5 page: \"The RE-A5 tube is 3/4\" longer than a standard carbine tube\" (7 15/16 is 11/16 longer than the mil-spec carbine tube's 7.25 on Magpul's drawing, std.receiver_extension's source; the 3/4 is a round figure)."},"tube_front_behind_pin":{"label":"The tube's front face behind the takedown pin (how far it screws in)","kind":"length","measurements":[{"id":"std","value":0.669,"unit":"in","pm":0.02,"source":{"type":"derived","expr":"-{std.receiver_extension.front_face_x}","via":"harvest"},"note":"The Army's drawings: a mil-spec tube is screwed in until its edge stands over the buffer retainer's shoulder."}],"note":"Hidden inside the receiver: what it moves is the relief, the rail's lip and ramp, the channel and the seven holes. VLTOR's thread is the mil-spec one (\"Thread 1-3/16 x 16 (mil-spec)\", https://vltor.com/a5)."},"position_step":{"label":"The stock position step","kind":"length","measurements":[{"id":"vltor","value":0.65,"unit":"in","pm":0.0005,"stated":"Position Spacing 0.650\"","source":{"type":"spec","publisher":"manufacturer","name":"VLTOR, A5 Buffer System page, its RE-A5 RECEIVER EXTENSION table","url":"https://vltor.com/a5","retrieved":"2026-10-28","via":"harvest"}},{"id":"photo","value":0.651,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/vltor-a5-receiver-extension 4b0990a26750 (VLTOR's photograph of the tube standing on its rear face, the rail's channel toward the left and toward the lens, 2359 x 1572)","scaleRef":"the tube's length (tube_length, 7 15/16 in) from its mouth (the rim's middle, 142 px) to its rear face (1460 px): 166 px/in along the tube","method":"the lit rims of six holes seen in the channel, the brightest row of each in a column down the channel (x 1068 to 1095): 727, 837, 946, 1053, 1160, 1267 px, 108.0 px apart on average (540 px over five steps)","via":"harvest"}}],"adopt":{"from":"vltor","reason":"The maker's figure; VLTOR's photograph of the tube's holes gives the same."}},"position_hole_d":{"label":"The position holes' diameter (in the rail's channel)","kind":"length","measurements":[{"id":"photo","value":0.3,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/vltor-a5-receiver-extension 4b0990a26750 (VLTOR's photograph of the tube standing, the channel toward the lens at a slant; a crop of x 1050 to 1110, y 680 to 1000 at four times with its levels stretched, an.holes)","scaleRef":"the tube's length (tube_length, 7 15/16 in), 166 px/in along the tube; the holes' own pitch (position_step, 0.650) gives 164","method":"each hole shows as a half circle standing out of the channel's far wall (wider than the channel); its length along the tube, the one size a slant view keeps: 52 and 50 px for the second and third holes","via":"harvest"},"note":"Narrower than the 0.42 read on BCM's mil-spec tube (bcm-receiver-extension.position_hole_d)."}]},"position_hole_rear_from_rear":{"label":"The rear (seventh) position hole's centre ahead of the tube's rear face","kind":"length","measurements":[{"id":"photo","value":0.63,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/vltor-a5-receiver-extension 4b0990a26750 (the holes in the channel, an.holes) and ffe8eb512fc6 (VLTOR's photograph of the tube standing, its numbered side toward the lens, 2317 x 1544)","scaleRef":"the holes' own pitch (position_step, 0.650 in): 106.5 px a step in 4b0990a26750, 163.8 px/in; the tube's length (164 px/in) in ffe8eb512fc6","method":"the middles of the half circles the first three holes make in the channel's wall, 717, 824 and 930 px, carried on at the pitch to the seventh, 1356 px: 104 px (0.635 in) ahead of the rear face at 1460. The engraved 7 beside it in ffe8eb512fc6 (the white figure's middle, 1363 px; rear face 1460): 0.64 in. The two agree.","via":"harvest"}}]},"channel_front_from_rear":{"label":"The channel along the rail's underside, its front end ahead of the tube's rear face","kind":"length","measurements":[{"id":"photo","value":4.64,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/vltor-a5-receiver-extension 4b0990a26750 (VLTOR's photograph of the tube standing, the channel toward the lens at a slant)","scaleRef":"the tube's length (tube_length, 7 15/16 in), 166 px/in along the tube (mouth 142 px, rear face 1460 px)","method":"the channel's front rounded end at 690 px on a crop with its levels stretched (an.c1): 3.30 in behind the mouth, 4.64 ahead of the rear face","via":"harvest"}}],"note":"The RE-A5 has a long recess along its rail's underside with rounded ends, the seven holes in its floor: VLTOR's 4b0990a26750 shows it from the side and below as a dark slot from the ramp's foot almost to the rear end."},"channel_rear_from_rear":{"label":"The channel along the rail's underside, its rear end ahead of the tube's rear face","kind":"length","measurements":[{"id":"photo","value":0.35,"unit":"in","pm":0.1,"source":{"type":"photo","photo":"references/vltor-a5-receiver-extension 4b0990a26750 (VLTOR's photograph of the tube standing, the channel toward the lens at a slant)","scaleRef":"the tube's length (tube_length, 7 15/16 in), 166 px/in along the tube","method":"the channel's rear rounded end at 1400 px, 60 px ahead of the rear face (1460 px). The rear face's own photograph (20475bac1645) has the rail's rear end whole under the tube, so the channel stops short of it.","via":"harvest"}}]},"channel_width":{"label":"The channel along the rail's underside, its width","kind":"length","measurements":[{"id":"assumed","value":0.25,"unit":"in","pm":0.06,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows the rail's underside square on. In 4b0990a26750 the channel is about three fifths of the rail's face as it is seen, with flats either side of it, and each hole (position_hole_d, 0.30) stands out of its far wall as a half circle: the channel is narrower than the holes.","via":"harvest"}}]},"channel_depth":{"label":"The channel along the rail's underside, its depth","kind":"length","measurements":[{"id":"assumed","value":0.08,"unit":"in","pm":0.04,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows the channel in section. In 4b0990a26750 (an.holes) its inside is dark from wall to wall and the holes' rims stand in its far wall as half circles, so it is deeper than a skin cut; under half the rail's depth below the tube is left for the holes.","via":"harvest"}}]},"rail_ramp_start":{"label":"The rail's ramp, where it leaves the lip, behind the tube's front face","kind":"length","measurements":[{"id":"photo","value":2.33,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/vltor-a5-receiver-extension ffe8eb512fc6 and 4b0990a26750 (VLTOR's two photographs of the tube standing, the rail to the right in one and to the left in the other)","scaleRef":"the tube's length (tube_length, 7 15/16 in): 164 and 166 px/in along the tube","method":"where the rail's silhouette leaves the tube's, its edge's run along the ramp extended back to the body's edge: 540 px in ffe8eb512fc6 (mouth 155), 2.35 in; 526 px in 4b0990a26750 (mouth 142), 2.31 in","via":"harvest"}}],"note":"The mil-spec carbine tube's ramp on Magpul's drawing begins 2.326 behind its front face and is at full depth by 2.592, at 45° (std.receiver_extension.rail_ramp_start, rail_ramp_end); VLTOR's begins at the same place and runs down at about 32° to full depth half an inch further back (rail_ramp_end)."},"rail_ramp_end":{"label":"The rail's ramp, where it reaches the rail's full depth, behind the tube's front face","kind":"length","measurements":[{"id":"photo","value":2.8,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/vltor-a5-receiver-extension ffe8eb512fc6 and 4b0990a26750","scaleRef":"the tube's length (tube_length, 7 15/16 in): 164 and 166 px/in along the tube","method":"where the rail's silhouette stops growing: 622 px in ffe8eb512fc6 (2.85 in from the mouth at 155), 604 px in 4b0990a26750 (2.78 in from 142)","via":"harvest"}}]},"rail_lip_depth":{"label":"The rail's lip ahead of the ramp, how far it stands under the tube","kind":"length","measurements":[{"id":"photo","value":0.04,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/vltor-a5-receiver-extension 4b0990a26750 (the tube standing, the rail to the left and turned toward the lens)","scaleRef":"the tube's length (tube_length, 7 15/16 in), 166 px/in","method":"the lip's edge 4 to 6 px outside the tube's own edge between the relief and the ramp (rows 412 to 512, 1099 px against 1103 to 1105 above it). The rail is turned toward the lens in this view, so what shows is its depth foreshortened and a little of its width: the ± is that.","via":"harvest"}}],"note":"Between the relief behind the thread and the ramp the rail is a low lip under the tube (VLTOR's \"VLTOR PAT PEND RE-A5\" is engraved on its side), as on the mil-spec tube."},"relief_end":{"label":"The relief behind the thread, where the tube's full diameter begins, behind its front face","kind":"length","measurements":[{"id":"photo","value":1.51,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/vltor-a5-receiver-extension ffe8eb512fc6 (the tube standing, 2317 x 1544) and 4b0990a26750 as the kit's picture uses it (references/vltor-a5-buffer-spring ba600a518974, lying, 718 px long)","scaleRef":"the tube's length (tube_length, 7 15/16 in): 164 px/in in ffe8eb512fc6; 90.5 px/in in ba600a518974","method":"the shoulder where the edge steps out from the relief to the body: 405 px in ffe8eb512fc6 (1.52 in from the mouth at 155; the relief is 181 px across against the body's 185); 386 px in ba600a518974 (1.51 in from the mouth at 249), where the rail's lip begins under it","via":"harvest"}}],"note":"Behind the thread's last crest the tube runs on a little under its own diameter, at about the thread's root, to a shoulder where the tube's body and the rail's lip begin: a thread relief."},"thread_length":{"label":"The thread's length, from the mouth to its last crest","kind":"length","measurements":[{"id":"photo","value":1.1,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/vltor-a5-receiver-extension ffe8eb512fc6 (the tube standing, its left edge's crests) and 4b0990a26750 as the kit's picture uses it (references/vltor-a5-buffer-spring ba600a518974, its top edge's crests)","scaleRef":"the thread's own pitch, 1/16 in (std.receiver_extension.thread_pitch): 10.06 px a crest in ffe8eb512fc6, 5.6 px in ba600a518974","method":"from the mouth to the last crest: in ffe8eb512fc6 a plain lip (163 to 172 px), a run-in, then 15 crests 185 to 326 px and the last at 331, 176 px from the mouth at 155 (17.5 turns, 1.09 in); in ba600a518974 crests from 262 to 349 px, 100 px from the mouth at 249 (1.10 in)","via":"harvest"}},{"id":"std","value":1.181,"unit":"in","pm":0.01,"source":{"type":"derived","expr":"{std.receiver_extension.thread_length}","via":"harvest"},"note":"The reference model's carbine tube's."}],"adopt":{"from":"photo","reason":"VLTOR's own tube, counted on two of its photographs that agree; the reference model's carbine tube is another maker's thread, a turn and a quarter longer."},"note":"VLTOR's thread is the mil-spec one: \"Thread 1-3/16 x 16 (mil-spec)\" (https://vltor.com/a5). How far it runs back is VLTOR's own: its crests counted on its photographs."},"rear_wall":{"label":"The rear wall's thickness, inside the tube","kind":"length","measurements":[{"id":"assumed","value":0.072,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no page states the RE-A5's bore length and no view shows inside it. Taken as the mil-spec carbine tube's on the reference model (std.receiver_extension.carbine_rear_wall, 0.072): VLTOR's rear face (20475bac1645) is closed, flat and engraved, with a small hole at its middle, as the carbine tube's is.","via":"harvest"}}]},"rear_edge_round":{"label":"The round on the rear face's outer edge","kind":"length","measurements":[{"id":"assumed","value":0.04,"unit":"in","pm":0.02,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: VLTOR's photograph of the rear face (20475bac1645) shows its outer edge, and the rail's rear corners, broken by a small round that catches the light all round, a few hundredths of an inch across against the 1.148 face; it isn't seen in profile.","via":"harvest"}}]},"relief_d":{"label":"The relief behind the thread, its diameter","kind":"length","measurements":[{"id":"photo","value":1.123,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/vltor-a5-receiver-extension ffe8eb512fc6 (the tube standing, 2317 x 1544)","scaleRef":"the tube's own outside diameter beside it (tube_od, 1.148 in): the relief and the body are the same black at the same depth, so their silhouettes thin alike and their ratio holds","method":"the silhouette's width, rows 336 to 404 against rows 420 to 530 (threshold 200): 181 px against 185 px; 1.148 x 181/185. Between the thread's roots (std.receiver_extension.thread_minor_d, 1.109) and the body.","via":"harvest"}}]}}},{"subject":"vltor-a5h2-buffer","title":"VLTOR A5H2 Buffer, 5.3 oz.","dimensions":{"weight":{"label":"Weight (its class: carbine, H, H2…)","kind":"mass","measurements":[{"id":"vltor","value":5.3,"unit":"oz","stated":"Weight 5.3 oz","source":{"type":"spec","publisher":"manufacturer","name":"VLTOR, A5H2 Buffer, 5.3 oz. (SKU A5H2), SPECIFICATIONS","url":"https://vltor.com/products/a5h2","retrieved":"2026-10-28","via":"harvest"}},{"id":"bigtex","value":5.33,"unit":"oz","stated":"A5H2: 5.33oz","source":{"type":"spec","publisher":"retailer","name":"Big Tex Ordnance, VLTOR A5 Buffer (BTODS26), its list \"Weights for the A5 buffers\"; its variant list says \"A5H2, Standard (5.3oz)\"","url":"https://www.bigtexordnance.com/product/vltor-a5-buffers/","retrieved":"2026-10-28","via":"harvest"}}],"adopt":{"from":"vltor","reason":"The maker's own figure; a seller's list gives a figure a hundredth finer that agrees with it to its last digit, and the same seller's variant names 5.3."},"note":"The A5H2 is the second of VLTOR's five A5 buffers by weight (A5H0 3.8, A5H1 4.56, A5H2 5.3, A5H3 6.08, A5H4 6.83 oz, https://vltor.com/a5): \"Each buffer has 4 internal weights — the \"H\" number indicates how many are tungsten (heavier) vs. steel (lighter).\" Its weights are inside it and don't show, so the model's volume isn't held to this."},"length":{"label":"Length (the head's front face to the bumper's end)","kind":"length","measurements":[{"id":"photo","value":3.7,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/vltor-a5-buffer-spring 2531fc1da290 (VLTOR's picture of its SP-A5 kit: the A5H2 standing, its head down, 1024 x 683) and ba600a518974 (its A5 Buffer Kit picture: the same picture of the buffer, 60 px across its body in both)","scaleRef":"the buffer's own three diameters, the standard's (std.carbine_buffer.head_d 0.98, pilot_d 0.781, body_d 0.687): 86 to 87, 69 and 60 px, in the standard's ratios (0.80 and 0.70 of the head, against 0.797 and 0.701)","method":"its length from the bumper's end (253 px) to the head's front face (580 px), 327 px: 3.68 in by the head, 3.70 by the step, 3.74 by the body. The picture looks a little down on it (the bumper's end shows as an ellipse about a fifth as tall as it is wide: 12°), which shortens it 2%; the ± covers that and the edges. On the kit picture beside the tube (ba600a518974) it is at the tube's own scale within 2 to 3.5% (90.5 px/in by the tube's 7 15/16), and reads 3.61 there.","via":"harvest"}},{"id":"vltor-table","value":4,"unit":"in","pm":0.0625,"stated":"Buffer Length Short (3.25\") 3/4\" longer — more mass distribution","source":{"type":"derived","expr":"3.25in + 0.75in","basis":"VLTOR's A5 page, its CARBINE vs. A5 table, the row Buffer Length: the carbine's \"Short (3.25\")\" and the A5's \"3/4\" longer\", added. The ± is a sixteenth: the same page's \"3/4\" longer\" for the tube is 11/16 by VLTOR's own lengths.","via":"harvest"},"note":"https://vltor.com/a5, retrieved 2026-10-28."}],"adopt":{"from":"photo","reason":"VLTOR's photograph of the buffer, read by its own diameters in the standard's proportions, which three of them keep to 1.5%. The table's \"3/4\" longer\" is a round comparison in a table whose other rows are loose (it gives a carbine tube \"4 positions\", where a carbine tube has six), and taken as a length it contradicts VLTOR's own sentence beside it, \"The receiver extension is longer to allow more bolt carrier travel\": in the RE-A5 as drawn (its front face, length and the carbine tube's rear wall) a 4.0 in buffer leaves the carrier 0.06 in less travel than a carbine buffer has in a carbine tube, and the 3.7 of the photograph 0.24 more. Kept beside it."},"note":"No page states it. VLTOR's A5 page, of the buffer: \"A5 buffers ... The buffers themselves are longer than traditional carbine buffers, and they cannot be used in standard carbine receiver extensions\" (https://vltor.com/products/a5h2); \"If you put an A5 buffer in a carbine tube, the buffer is too long — it will prevent the carrier from cycling fully\"; \"The receiver extension is longer to allow more bolt carrier travel. The buffer is longer to house an additional tungsten weight.\" (https://vltor.com/a5)."},"od":{"label":"Diameter (its head, which runs in the extension's bore)","kind":"length","measurements":[{"id":"std","value":0.98,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.carbine_buffer.head_d}","via":"harvest"},"note":"The standard carbine buffer's head: VLTOR's picture of the A5H2 (2531fc1da290) has its head, the step behind it and its body in the standard's proportions (86 to 87, 69 and 60 px for 0.98, 0.781 and 0.687)."}],"note":"It runs in the RE-A5's bore, the mil-spec 1.000 (std.receiver_extension.bore_d; VLTOR: \"MilSpec Diameter\" for the tube)."},"body_length":{"label":"The body's length (the head's front face to the body's open end, where the bumper comes out)","kind":"length","measurements":[{"id":"derived","value":3.3,"unit":"in","pm":0.09,"source":{"type":"derived","expr":"{.length} - {std.carbine_buffer.bumper_exposed}","via":"harvest"},"note":"Its length less the standard bumper standing out of it: VLTOR's picture has the bumper 34 px of the 327 (0.38 to 0.40 in by the buffer's diameters), the standard's 0.40."}]},"pin_from_open_end":{"label":"The pin through the body and the bumper, from the body's open end","kind":"length","measurements":[{"id":"photo","value":0.19,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/vltor-a5-buffer-spring 2531fc1da290 (VLTOR's picture of the SP-A5 kit, the A5H2 standing, its head down)","scaleRef":"the buffer's head, the standard's 0.98 in (od): 86.5 px","method":"the pin's middle at 303 px against the body's open end, where the bumper comes out, at 287 px on a crop at three times: 16 px","via":"harvest"}},{"id":"std","value":0.24,"unit":"in","pm":0.005,"source":{"type":"derived","expr":"{std.carbine_buffer.pin_from_open_end}","via":"harvest"},"note":"The Army's drawing of the rifle buffer's body."}],"adopt":{"from":"photo","reason":"VLTOR's own buffer; the standard's place is 0.05 further in, at the photo's ± from it."},"note":"The pin shows in VLTOR's pictures as a small round head in a hole near the bumper (2531fc1da290, ba600a518974)."}}},{"subject":"vltor-castle-nut","title":"VLTOR Receiver Extension Lock Nut","dimensions":{"od":{"label":"Outside diameter","kind":"length","measurements":[{"id":"model","value":1.363,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"one cylinder, r 0.6815 (.cache/buffer/std/faces.Buffer_Tube_Nut.txt; as read for guntec-ar15-castle-nut, 2026-10-20)","via":"user"},"note":"A mil-spec nut as the reference model has it: VLTOR's picture has no size of its own, and every reading on it below is scaled by this."}]},"thickness":{"label":"Thickness","kind":"length","measurements":[{"id":"photo","value":0.334,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/vltor-castle-nut 2531fc1da290 (VLTOR's picture of its SP-A5 kit: the nut alone from behind and above, 1024 x 683; its A5 Buffer Kit picture ba600a518974 has the same cut-out)","scaleRef":"the nut's own outside diameter (od, 1.363 in): its outline's width, 141 px (rows 513 to 519, 427 to 567); the rear face's outer ellipse is half as tall as wide (477 to about 547, 70 px), so the picture looks down 30 degrees and the axis is drawn at cos 30 degrees","method":"the side band below the rear face's near rim, at the middle: 547 to 577, 30 px, over cos 30 degrees, 34.6 px: 0.245 of the outside diameter","via":"harvest"}},{"id":"model","value":0.3765,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Nut.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11)","method":"its front face to its rear face, planes y 0 and y 0.3765 (as read for guntec-ar15-castle-nut)","via":"user"},"note":"A mil-spec nut as the reference model has it."}],"adopt":{"from":"photo","reason":"VLTOR's own nut, by its picture's proportions; the reference model's nut is another maker's, 0.04 thicker."}},"notches":{"label":"Notches on its rear face","kind":"count","measurements":[{"id":"photo","value":4,"unit":"count","source":{"type":"photo","photo":"references/vltor-castle-nut 2531fc1da290 (VLTOR's kit picture: the nut from behind and above, the whole rim of its rear face in view)","scaleRef":"none: a count","method":"four notches round the rim (crop an.nut, five times): at the far side, at the right, at the front left and at the left; their places on the rear face's ellipse, taken back to a circle, are 92, 94, 85 and 89 degrees apart. No fifth: every stretch of the rim between them is in view.","via":"harvest"}},{"id":"product","value":4,"unit":"count","source":{"type":"photo","photo":"references/vltor-castle-nut a899784bf2cd (VLTOR's photograph of the nut sold alone, V2-1069-M3, from its notched face turned about 29 degrees, 1024 x 683)","scaleRef":"none: a count","method":"four notches (crop an.nut2, three times): one through the wall at the right, one through the bore at the far left, two on the near rim between them","via":"harvest"}}],"adopt":{"from":"product","reason":"Counted on both of VLTOR's pictures: four."}},"notch_width":{"label":"A notch's width","kind":"length","measurements":[{"id":"photo","value":0.12,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/vltor-castle-nut 2531fc1da290","scaleRef":"the outside diameter (od, 1.363 in), 141 px across","method":"the notch at the far side, 12 px across the rim where it runs across the picture (rows 483 to 486, 518 to 529 px); the one at the front left, 12 px where the rim runs at 70 degrees to the picture's rows (13 px along it)","via":"harvest"}},{"id":"product","value":0.123,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/vltor-castle-nut a899784bf2cd (VLTOR's photograph of the nut sold alone, V2-1069-M3, from its notched face turned about 29 degrees, 1024 x 683)","scaleRef":"the outline's height, the outside diameter seen square (od, 1.363 in): 298 px (rows 175 to 473), 218.6 px/in; across, the ring is drawn 260 px wide, so its face is turned 29 degrees and the axis is drawn at sin 29 degrees","method":"the notch through the wall at the right, along the outline's height where it runs up the picture: 27 px","via":"harvest"}}],"adopt":{"from":"product","reason":"VLTOR's photograph of the nut alone; the kit picture's reading agrees."}},"notch_depth":{"label":"A notch's depth (into the rear face)","kind":"length","measurements":[{"id":"photo","value":0.134,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/vltor-castle-nut 2531fc1da290","scaleRef":"the outside diameter (od, 1.363 in), 141 px across; the axis drawn at cos 30 degrees (thickness)","method":"the front-left notch's floor 12 px under the rim on a crop at five times (an.nut), over cos 30 degrees","via":"harvest"}},{"id":"product","value":0.112,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/vltor-castle-nut a899784bf2cd (VLTOR's photograph of the nut sold alone, V2-1069-M3, from its notched face turned about 29 degrees, 1024 x 683)","scaleRef":"the outline's height, the outside diameter seen square (od, 1.363 in): 298 px (rows 175 to 473), 218.6 px/in; across, the ring is drawn 260 px wide, so its face is turned 29 degrees and the axis is drawn at sin 29 degrees","method":"the notch through the wall at the right, its floor 12 px in from the rim across the picture, over sin 29 degrees","via":"harvest"}}],"adopt":{"from":"product","reason":"VLTOR's photograph of the nut alone; the kit picture's reading agrees within the ± of both."}},"edge_break":{"label":"The edges' break","kind":"length","measurements":[{"id":"assumed","value":0.012,"unit":"in","pm":0.006,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the picture shows the rear face's edges a little rounded where the light catches them; how much isn't read.","via":"harvest"}}]},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"metal","value":0.531,"unit":"oz","pm":0.06,"source":{"type":"derived","expr":"(0.785398163 * ({.od} * {.od} - {std.receiver_extension.thread_major_d} * {std.receiver_extension.thread_major_d}) * {.thickness} - 4 * {.notch_width} * {.notch_depth} * ({.od} - {std.receiver_extension.thread_major_d}) / 2) * {std.density.steel}","via":"harvest"}}],"note":"No page states it. Worked out from its sizes as steel (VLTOR names no material; the mil-spec nut is steel): a ring of its outside diameter and thickness round the extension's thread's crests, less its four notches. A derived figure, for the build's total."}}},{"subject":"vltor-lockplate","title":"VLTOR Receiver Extension End Plate","dimensions":{"thickness":{"label":"Thickness","kind":"length","measurements":[{"id":"model","value":0.124,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the plate's two faces, planes y 0 and y 0.1240 (.cache/buffer/std/faces.Buffer_Tube_Rotation_Lock.txt)","via":"user"},"note":"A mil-spec plate as the reference model has it: Guntec's plate has that plate's outline on three photos (top_above_axis, bottom_below_axis, boss_width)."}]},"top_above_axis":{"label":"End plate top above the tube axis (its ring's radius)","kind":"length","measurements":[{"id":"model","value":0.6817,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the ring's outer cylinder, r 0.6817 (#899)","via":"user"}},{"id":"photo","value":0.72,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/vltor-lockplate 2531fc1da290 (VLTOR's picture of its SP-A5 kit: the lockplate lying face on, a little tilted, 1024 x 683; its A5 Buffer Kit picture ba600a518974 has the same cut-out)","scaleRef":"across: the hole's width as a mil-spec plate's (hole_d, 1.1902 in), 127 px: 106.7 px/in; down: the hole's own height, 119 px for the same 1.1902 (the plate is tilted 20 degrees down the picture): 100 px/in","method":"the ring's top edge (row 366) above the hole's middle (row 438, where the hole is widest)","via":"harvest"}},{"id":"product","value":0.683,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/vltor-lockplate dd62a391c0ba (VLTOR's photograph of the plate sold alone, V2-1069-M1, its rear face square on, 1024 x 683)","scaleRef":"its hole as a mil-spec plate's (hole_d, 1.1902 in): 279 px across and 278 down, round to the pixel: 234.4 px/in","method":"the ring's top edge (row 85) above the hole's middle (row 245)","via":"harvest"}}],"adopt":{"from":"model","reason":"The mil-spec plate's (VLTOR: \"Mil-Spec Receiver Extension End Plate\"), which VLTOR's own photographs read within their ±."}},"bottom_below_axis":{"label":"End plate lobe bottom below the tube axis","kind":"length","measurements":[{"id":"model","value":1.3788,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the lobe's round end, r 0.4266 about a centre 0.9522 below the axis","via":"user"}},{"id":"photo","value":1.41,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/vltor-lockplate 2531fc1da290 (VLTOR's picture of its SP-A5 kit: the lockplate lying face on, a little tilted, 1024 x 683; its A5 Buffer Kit picture ba600a518974 has the same cut-out)","scaleRef":"across: the hole's width as a mil-spec plate's (hole_d, 1.1902 in), 127 px: 106.7 px/in; down: the hole's own height, 119 px for the same 1.1902 (the plate is tilted 20 degrees down the picture): 100 px/in","method":"the lobe's bottom (row 579) below the hole's middle","via":"harvest"}},{"id":"product","value":1.391,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/vltor-lockplate dd62a391c0ba (VLTOR's photograph of the plate sold alone, V2-1069-M1, its rear face square on, 1024 x 683)","scaleRef":"its hole as a mil-spec plate's (hole_d, 1.1902 in): 279 px across and 278 down, round to the pixel: 234.4 px/in","method":"the lobe's bottom (row 571) below the hole's middle","via":"harvest"}}],"adopt":{"from":"model","reason":"The mil-spec plate's (VLTOR: \"Mil-Spec Receiver Extension End Plate\"), which VLTOR's own photographs read within their ±."}},"lobe_radius":{"label":"End plate, the radius of its lobe's round end","kind":"length","measurements":[{"id":"model","value":0.4266,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the lobe's end cylinder, r 0.4266 (#973)","via":"user"},"note":"Redcon1's photo of Guntec's plate has the lobe's widths at three depths (as fractions of its height) 0.01 to 0.03 in over this outline's, after the outline's 0.04 of shadow is taken off: the lower rows, nearer the lens, read larger."}]},"lobe_centre_below_axis":{"label":"End plate, its lobe's round end's centre below the tube axis","kind":"length","measurements":[{"id":"model","value":0.9522,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the lobe's end cylinder's axis (#973)","via":"user"}}]},"key_width":{"label":"End plate, its key's width","kind":"length","measurements":[{"id":"model","value":0.125,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the key's side planes, x ±0.0625 (#1108, #1162)","via":"user"},"note":"The extension's slot it rides in is as wide (std.receiver_extension.key_slot_width)."},{"id":"photo","value":0.1,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/vltor-lockplate 2531fc1da290 (VLTOR's picture of its SP-A5 kit: the lockplate lying face on, a little tilted, 1024 x 683; its A5 Buffer Kit picture ba600a518974 has the same cut-out)","scaleRef":"across: the hole's width as a mil-spec plate's (hole_d, 1.1902 in), 127 px: 106.7 px/in; down: the hole's own height, 119 px for the same 1.1902 (the plate is tilted 20 degrees down the picture): 100 px/in","method":"the key standing up into the hole, 11 px across at row 494","via":"harvest"}},{"id":"product","value":0.115,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/vltor-lockplate dd62a391c0ba (VLTOR's photograph of the plate sold alone, V2-1069-M1, its rear face square on, 1024 x 683)","scaleRef":"its hole as a mil-spec plate's (hole_d, 1.1902 in): 279 px across and 278 down, round to the pixel: 234.4 px/in","method":"the key standing up into the hole, 27 px across (rows 385 to 395, 492 to 519)","via":"harvest"}}],"adopt":{"from":"model","reason":"The mil-spec plate's (VLTOR: \"Mil-Spec Receiver Extension End Plate\"), which VLTOR's own photographs read within their ±."}},"key_tip_below_axis":{"label":"End plate, its key's tip below the tube axis","kind":"length","measurements":[{"id":"model","value":0.5619,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the key's tip plane, z 0.5619 (#1135)","via":"user"},"note":"0.012 below the extension's slot floor (std.receiver_extension.key_slot_floor, 0.55): the key stands clear of it."},{"id":"product","value":0.576,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/vltor-lockplate dd62a391c0ba (VLTOR's photograph of the plate sold alone, V2-1069-M1, its rear face square on, 1024 x 683)","scaleRef":"its hole as a mil-spec plate's (hole_d, 1.1902 in): 279 px across and 278 down, round to the pixel: 234.4 px/in","method":"the key's tip at row 380, between the rows without it and with it","via":"harvest"}}],"adopt":{"from":"model","reason":"The mil-spec plate's (VLTOR: \"Mil-Spec Receiver Extension End Plate\"), which VLTOR's own photographs read within their ±."}},"relief_bottom_below_axis":{"label":"End plate, the V either side of its key: its floor below the tube axis","kind":"length","measurements":[{"id":"model","value":0.6575,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the two sloped planes' lower ends, z 0.6575 (#1054, #1216), where 0.031 in rounds turn them into the key's sides","via":"user"}}]},"relief_floor_half_width":{"label":"End plate, the V either side of its key: where its sloped sides end, out from the middle","kind":"length","measurements":[{"id":"model","value":0.1119,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the sloped planes' inner ends, x ±0.1119 (#1054, #1216)","via":"user"}}]},"relief_top_half_width":{"label":"End plate, the V either side of its key: where it leaves the hole's circle, out from the middle","kind":"length","measurements":[{"id":"model","value":0.354,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the hole's cylinder ends at x ±0.3540, z 0.4784 (#1007), where the sloped planes begin","via":"user"}}]},"relief_fillet_r":{"label":"End plate, the round at the bottom of the V either side of its key, where it turns into the key's side","kind":"length","measurements":[{"id":"model","value":0.031,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"two cylinders r 0.031 at x ±0.0935, z 0.6326 (#1081, #1189)","via":"user"}}]},"side_angle":{"label":"End plate, its lobe's straight sides: how far each leans in from upright","kind":"angle","measurements":[{"id":"model","value":13.5,"unit":"deg","pm":0.05,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the side planes' normals (#946, #1000: 0.972, 0.233), whose lean is atan(0.233 / 0.972)","via":"user"}}]},"corner_angle":{"label":"End plate, where each straight side meets the ring: its angle below the level of the tube axis","kind":"angle","measurements":[{"id":"model","value":31.33,"unit":"deg","pm":0.05,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the side planes' upper ends, x ±0.5823, 0.3545 below the axis, on the ring's r 0.6817: atan(0.3545 / 0.5823)","via":"user"}}]},"boss_proud":{"label":"End plate, how far its boss stands out of its front face","kind":"length","measurements":[{"id":"model","value":0.0645,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the boss's face, plane y 0.1885 of a plate 0.1240 thick","via":"user"},"note":"No photo on file shows Guntec's boss in profile."}],"note":"The mil-spec plate's stamped boss and dimple, as deep as the reference model has them: VLTOR's photographs show its dimple from behind only, its width and height and place as the mil-spec plate's (pocket_width, pocket_height, boss_below_axis), and no view shows a depth or the front face."},"dimple_depth":{"label":"End plate, the dimple in its rear face behind the boss","kind":"length","measurements":[{"id":"model","value":0.063,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"plane y 0.0630; the dimple is the boss's outline 0.005 larger all round","via":"user"},"note":"No photo on file shows Guntec's dimple in profile."}],"note":"The mil-spec plate's stamped boss and dimple, as deep as the reference model has them: VLTOR's photographs show its dimple from behind only, its width and height and place as the mil-spec plate's (pocket_width, pocket_height, boss_below_axis), and no view shows a depth or the front face."},"dimple_grow":{"label":"End plate, how much larger all round its dimple is than its boss","kind":"length","measurements":[{"id":"model","value":0.005,"unit":"in","pm":0.001,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the dimple's ends r 0.1925 against the boss's r 0.1875 (#1433, #1223)","via":"user"}}],"note":"The mil-spec plate's stamped boss and dimple, as deep as the reference model has them: VLTOR's photographs show its dimple from behind only, its width and height and place as the mil-spec plate's (pocket_width, pocket_height, boss_below_axis), and no view shows a depth or the front face."},"hole_d":{"label":"The hole's diameter","kind":"length","measurements":[{"id":"std","value":1.1902,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{std.receiver_extension.end_plate_hole_d}","via":"harvest"},"note":"A mil-spec plate's hole, as the reference model has it: VLTOR's kit picture is scaled by it (the ring's width then reads 1.368, the reference model's 1.363)."}]},"ring_width":{"label":"The ring's width across","kind":"length","measurements":[{"id":"photo","value":1.368,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/vltor-lockplate 2531fc1da290 (VLTOR's picture of its SP-A5 kit: the lockplate lying face on, a little tilted, 1024 x 683; its A5 Buffer Kit picture ba600a518974 has the same cut-out)","scaleRef":"across: the hole's width as a mil-spec plate's (hole_d, 1.1902 in), 127 px: 106.7 px/in; down: the hole's own height, 119 px for the same 1.1902 (the plate is tilted 20 degrees down the picture): 100 px/in","method":"the outline's widest, row 438: 738 to 883 px, 146 px","via":"harvest"}},{"id":"product","value":1.378,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/vltor-lockplate dd62a391c0ba (VLTOR's photograph of the plate sold alone, V2-1069-M1, its rear face square on, 1024 x 683)","scaleRef":"its hole as a mil-spec plate's (hole_d, 1.1902 in): 279 px across and 278 down, round to the pixel: 234.4 px/in","method":"the outline's widest, rows 235 to 255: 346 to 668 px, 323 px","via":"harvest"}}],"adopt":{"from":"product","reason":"VLTOR's photograph of the plate sold alone, square on; the kit picture's reading agrees."},"note":"A check of the scale on the picture against the reference model's ring (twice top_above_axis)."},"boss_width":{"label":"End plate, its boss side to side","kind":"length","measurements":[{"id":"model","value":0.496,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"an obround: two r 0.1875 ends at x ±0.0605","via":"user"}}]},"boss_height":{"label":"End plate, its boss top to bottom","kind":"length","measurements":[{"id":"model","value":0.375,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the obround's two ends' diameter","via":"user"}}]},"boss_below_axis":{"label":"End plate, its boss's middle below the tube's axis","kind":"length","measurements":[{"id":"model","value":0.9974,"unit":"in","pm":0.002,"source":{"type":"model","file":"references/AR15_Complete_CAD_Reference_Model_and_Technical_Data_Package/…/STEP/AR-15-Complete_Assembly/AR-15_split/Buffer_Tube_Rotation_Lock.step.step (the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock)","method":"the obround's centre","via":"user"}},{"id":"product","value":1.011,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/vltor-lockplate dd62a391c0ba (VLTOR's photograph of the plate sold alone, V2-1069-M1, its rear face square on, 1024 x 683)","scaleRef":"its hole as a mil-spec plate's (hole_d, 1.1902 in): 279 px across and 278 down, round to the pixel: 234.4 px/in","method":"the middle of the dimple in the rear face (crop an.plate2, four times): row 481.9, 236.9 px below the hole's middle","via":"harvest"}},{"id":"kit","value":1,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/vltor-lockplate 2531fc1da290 (VLTOR's picture of its SP-A5 kit: the plate face on, tilted 20 degrees, 1024 x 683)","scaleRef":"across: the hole's width as a mil-spec plate's, 127 px: 106.7 px/in; down: the hole's own height, 119 px: 100 px/in","method":"the dimple's middle at row 540, 102 px below the hole's middle at row 438","via":"harvest"}}],"adopt":{"from":"model","reason":"The mil-spec plate's; VLTOR's two photographs put the dimple's middle within their ± of it."}},"pocket_width":{"label":"The dimple in the rear face (VLTOR's V is in it), its width across","kind":"length","measurements":[{"id":"derived","value":0.506,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{.boss_width} + 2 * {.dimple_grow}","via":"harvest"}},{"id":"product","value":0.49,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/vltor-lockplate dd62a391c0ba (VLTOR's photograph of the plate sold alone, V2-1069-M1, its rear face square on, 1024 x 683)","scaleRef":"its hole as a mil-spec plate's (hole_d, 1.1902 in): 279 px across and 278 down, round to the pixel: 234.4 px/in","method":"the dimple's rim across (crop an.plate2, four times): 115 px","via":"harvest"}}],"adopt":{"from":"derived","reason":"The mil-spec plate's dimple; VLTOR's photograph reads it within its ±."},"note":"What shows of the boss on the rear face: the mil-spec plate's dimple, as much larger all round than the boss as the reference model has it."},"pocket_height":{"label":"The dimple in the rear face, its height","kind":"length","measurements":[{"id":"derived","value":0.385,"unit":"in","pm":0.003,"source":{"type":"derived","expr":"{.boss_height} + 2 * {.dimple_grow}","via":"harvest"}},{"id":"product","value":0.4,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/vltor-lockplate dd62a391c0ba (VLTOR's photograph of the plate sold alone, V2-1069-M1, its rear face square on, 1024 x 683)","scaleRef":"its hole as a mil-spec plate's (hole_d, 1.1902 in): 279 px across and 278 down, round to the pixel: 234.4 px/in","method":"the dimple's rim down (crop an.plate2, four times): 94 px","via":"harvest"}}],"adopt":{"from":"derived","reason":"The mil-spec plate's dimple; VLTOR's photograph reads it within its ±."}},"edge_break":{"label":"The edges' break","kind":"length","measurements":[{"id":"assumed","value":0.012,"unit":"in","pm":0.006,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows its edges in profile. A plate's edges are broken a little, and a sharp edge reads as a line of light in the app.","via":"harvest"}}]},"height":{"label":"Height","kind":"length","measurements":[{"id":"derived","value":2.0605,"unit":"in","pm":0.002,"source":{"type":"derived","expr":"{.top_above_axis} + {.bottom_below_axis}","via":"harvest"}}]},"face_area":{"label":"The face's area, the hole's included","kind":"length","measurements":[{"id":"derived","value":2.0875,"unit":"in","pm":0.004,"source":{"type":"derived","expr":"{.top_above_axis} * {.top_above_axis} * (180 + 2 * {.corner_angle}) * 3.14159265 / 360 + {.lobe_radius} * {.lobe_radius} * (180 - 2 * {.side_angle}) * 3.14159265 / 360 + {.lobe_radius} * {.lobe_centre_below_axis} * cos({.side_angle}) + {.top_above_axis} * cos({.corner_angle}) * ({.lobe_centre_below_axis} + {.lobe_radius} * sin({.side_angle})) - {.lobe_radius} * {.top_above_axis} * cos({.side_angle}) * sin({.corner_angle})","via":"harvest"}}],"note":"Worked out from the outline's figures, for the weight: the ring's arc between its corners, the lobe's end, the two straight sides and what lies between them (as guntec-ar15-end-plate's)."},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"metal","value":0.552,"unit":"oz","pm":0.03,"source":{"type":"derived","expr":"({.face_area} - 0.785398163 * {.hole_d} * {.hole_d}) * {.thickness} * {std.density.steel}","via":"harvest"}}],"note":"No page states it. Worked out from its metal as steel (VLTOR names no material; the mil-spec plate is steel): the face less the hole, times the thickness, times steel's density. A derived figure, for the build's total."}}},{"subject":"vortex-sport-cantilever-30mm-mount","title":"Vortex Sport Cantilever 30mm Mount","dimensions":{"optical_axis_above_rail":{"label":"Ring axis above the rail's top","kind":"length","measurements":[{"id":"vortex","value":1.5,"unit":"in","pm":0.005,"stated":"Center Scope Height 1.50\"","source":{"type":"spec","publisher":"manufacturer","name":"Vortex Optics, Sport Cantilever 30mm Mount (SCM-30-150): Specifications","url":"https://vortexoptics.com/sport-cantilever-mount-scm-30-150.html","retrieved":"2026-10-13","via":"harvest"}},{"id":"scheels","value":1.5,"unit":"in","pm":0.005,"stated":"Center Scope Height: 1.50\" (38.1mm)","source":{"type":"spec","publisher":"retailer","name":"Scheels, Vortex Sport Cantilever 30mm Mount (875874-SCM-30-150)","url":"https://www.scheels.com/p/875874-SCM-30-150","retrieved":"2026-10-13","via":"harvest"}},{"id":"sportsmans","value":1.5,"unit":"in","stated":"1.5in Optical Centerline","source":{"type":"spec","publisher":"retailer","name":"Sportsman's Warehouse, Vortex Optics Sport 30mm Cantilever Mount Matte Black - 1 Piece (Model SCM-30-150)","url":"https://www.sportsmans.com/hunting-gear-supplies/optics-binoculars-scopes-rangefinders/scope-rings-bases/vortex-optics-sport-30mm-cantilever-mount-matte-black-1-piece/p/1932637","retrieved":"2026-10-13","via":"harvest"}},{"id":"side","value":1.475,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount 910667d8ac8f (Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123)","scaleRef":"the receiver's rail slots (std.picatinny.slot_pitch), by the daylight through seven of them behind and under the mount, their centres at columns 666.52, 690.76, 714.94, 739.29, 811.72, 884.32 and 957.00 (slots -7 to -4, -1, 2 and 5 from the rear lug's): 24.207 px a slot, 61.44 px/in, no centre more than 0.15 px off the line; the rail's top is the teeth's top edge, row 417.4 under the mount (tilted 0.25 degrees with the picture)","method":"the 30 mm tube's centre line (its two edges' middle, row 326.8 over the base) above the rail's top: 90.6 px","via":"harvest"}}],"adopt":{"from":"vortex","reason":"The maker's figure, engraved on the mount; two sellers repeat it. The picture's reading is 0.025 under it, at the edge of what a pixel and the picture's scale allow."},"note":"Vortex's own word for it is \"Center Scope Height\"; Scheels gives the same in millimetres and Sportsman's calls it the optical centerline. The mount's rear end is engraved \"30MM 1.50\"\" (picture `bl`). The side view of it on a rifle reads 1.475 at the rail's scale: 1.7% under, with the 30 mm tube in it reading 1.9% thin in the same picture (71.2 px for 72.6); kept beside the maker's figure, which the model is built on."},"ring_bore":{"label":"Tube diameter the rings are bored for","kind":"length","measurements":[{"id":"vortex","value":30,"unit":"mm","stated":"Tube Size 30mm","source":{"type":"spec","publisher":"manufacturer","name":"Vortex Optics, Sport Cantilever 30mm Mount (SCM-30-150): Specifications","url":"https://vortexoptics.com/sport-cantilever-mount-scm-30-150.html","retrieved":"2026-10-13","via":"harvest"}},{"id":"scheels","value":30,"unit":"mm","stated":"Tube Size: 30 mm","source":{"type":"spec","publisher":"retailer","name":"Scheels, Vortex Sport Cantilever 30mm Mount (875874-SCM-30-150)","url":"https://www.scheels.com/p/875874-SCM-30-150","retrieved":"2026-10-13","via":"harvest"}},{"id":"sportsmans","value":30,"unit":"mm","stated":"30mm Ring Size","source":{"type":"spec","publisher":"retailer","name":"Sportsman's Warehouse, Vortex Optics Sport 30mm Cantilever Mount Matte Black - 1 Piece (Model SCM-30-150)","url":"https://www.sportsmans.com/hunting-gear-supplies/optics-binoculars-scopes-rangefinders/scope-rings-bases/vortex-optics-sport-30mm-cantilever-mount-matte-black-1-piece/p/1932637","retrieved":"2026-10-13","via":"harvest"}}],"adopt":{"from":"vortex","reason":"The maker's figure; the mount's rear end is engraved \"30MM 1.50\"\"."}},"weight":{"label":"Weight","kind":"mass","measurements":[{"id":"vortex","value":5.39,"unit":"oz","stated":"Weight 5.39 oz.","source":{"type":"spec","publisher":"manufacturer","name":"Vortex Optics, Sport Cantilever 30mm Mount (SCM-30-150): Specifications","url":"https://vortexoptics.com/sport-cantilever-mount-scm-30-150.html","retrieved":"2026-10-13","via":"harvest"}},{"id":"primary-arms","value":5.39,"unit":"oz","stated":"Weight 5.39 oz.","source":{"type":"spec","publisher":"retailer","name":"Primary Arms, Vortex Optics 30mm Sport Cantilever Mount - 1.5\" Height (SKU and MPN SCM-30-150)","url":"https://www.primaryarms.com/vortex-optics-30mm-sport-cantilever-mount-1-5in-height","retrieved":"2026-10-13","via":"harvest"}},{"id":"ar15discounts","value":5.39,"unit":"oz","stated":"Weight 5.39 oz","source":{"type":"spec","publisher":"retailer","name":"AR15Discounts, Vortex 30mm 1.5\" Sport Cantilever Mount - SCM-30-150 (Additional information)","url":"https://ar15discounts.com/products/vortex-30mm-1-5-sport-cantilever-mount/","retrieved":"2026-10-13","via":"harvest"},"note":"The same table has \"Dimensions 5 × 2 × 2.5 in\", unlabelled: longer than the mount is wide and not its length (5.35 as read); the shop's carton by every sign, and no dimension here rests on it."}],"adopt":{"from":"vortex","reason":"The maker's figure; the sellers repeat it."},"note":"Vortex's bullet beside it: \"Lightweight, under 5.5 oz. to keep your rifle portable without sacrificing stability\". KYGUNCO's page has \"Weight 1 lb\" for the same number (Style VRT-SCM-30-150): a shop's shipping weight, not the mount's, and not taken as a reading of it."},"offset_published":{"label":"The maker's \"2\\\" Offset\" (what it spans isn't said)","kind":"length","measurements":[{"id":"vortex","value":2,"unit":"in","stated":"2\" Offset","source":{"type":"spec","publisher":"manufacturer","name":"Vortex Optics, Sport Cantilever 30mm Mount (SCM-30-150): Specifications","url":"https://vortexoptics.com/sport-cantilever-mount-scm-30-150.html","retrieved":"2026-10-13","via":"harvest"}}],"note":"Published and undefined: Vortex's only sentence is \"The 2\" offset gets your head position and eye relief dialed, while leaving plenty of real estate on your rail.\"; Sportsman's Warehouse: \"With a 2in offset, this mount positions your scope forward\". Nothing is built on it. Tried on the side view (2026-10-13), no span of the mount comes to 2 in within its ±: the front ring's middle is 1.80 in ahead of the front jaw's front end (the end of the clamp), and that ring's front face 2.20 ahead of it; the middle between the two rings is 1.67 ahead of the clamp's middle. The figure reads as a round one for how far the front ring stands ahead of the clamp."},"ring_rear_x":{"label":"Rear ring, its middle ahead of the rear recoil lug","kind":"length","measurements":[{"id":"side","value":0.186,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount 910667d8ac8f (Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123)","scaleRef":"the receiver's rail slots (std.picatinny.slot_pitch), by the daylight through seven of them behind and under the mount, their centres at columns 666.52, 690.76, 714.94, 739.29, 811.72, 884.32 and 957.00 (slots -7 to -4, -1, 2 and 5 from the rear lug's): 24.207 px a slot, 61.44 px/in, no centre more than 0.15 px off the line; the rail's top is the teeth's top edge, row 417.4 under the mount (tilted 0.25 degrees with the picture)","method":"the ring's cap where it stands over the tube, its two ends at columns 825.4 and 869.3 (the top silhouette's steps, at the level midway between the tube's top and the cap's): their middle, 847.35, less the rear lug's 835.95","via":"harvest"}}],"note":"The mount has no cross bolt: its two recoil lugs lie in two neighbouring slots, and the part frame's origin is on the rail's top over the rear one's middle (column 835.95: the lug's own middle and the slot's, 0.05 px apart)."},"ring_front_x":{"label":"Front ring, its middle ahead of the rear recoil lug","kind":"length","measurements":[{"id":"side","value":3.611,"unit":"in","pm":0.07,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount 910667d8ac8f (Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123)","scaleRef":"the receiver's rail slots (std.picatinny.slot_pitch), by the daylight through seven of them behind and under the mount, their centres at columns 666.52, 690.76, 714.94, 739.29, 811.72, 884.32 and 957.00 (slots -7 to -4, -1, 2 and 5 from the rear lug's): 24.207 px a slot, 61.44 px/in, no centre more than 0.15 px off the line; the rail's top is the teeth's top edge, row 417.4 under the mount (tilted 0.25 degrees with the picture)","method":"the ring's cap over the tube, columns 1034.4 to 1081.2: their middle, 1057.8, less the rear lug's 835.95. This ring reads 2.9 px longer than the rear one (its front end is a soft edge, 3 px wide, where the rear one's ends are sharp): its middle is good to 1.5 px","via":"harvest"}}],"note":"The picture's scale is the rail's, good to 0.1% along the rail. What it leaves open: the scope and the mount in it read 1.7 to 1.9% small up and down by that scale (optical_axis_above_rail), which a black part's edges on white explain only in part, so the mount may be drawn a little smaller than the rifle in this picture; at that other scale (60.3 px/in) this figure would be 3.68 and the rings 3.49 apart. Two things say the rail's scale is the mount's: its lugs lie in the rail's slots a pitch apart, and the camera fitted to picture `fr`, whose scale is the 30 mm bore, puts the base's rear end 1.528 in behind the rear ring's middle, where this picture has 1.526 at the rail's scale and 1.555 at the other. The cameras themselves leave the rings' spacing open (3.58 and 3.41 in when it is left to them, each ± 0.02 formally): they agree with 3.425 and can't better it. The ± here covers the other scale."},"ring_length":{"label":"Each ring's length along the tube (face to face)","kind":"length","measurements":[{"id":"obliques","value":0.735,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount a1e22b679294 (Vortex, ..._30mm_fr_w.jpg: the mount alone from the front right and above) and 22565a4f580e (..._30mm_bl_w.jpg: from the rear left and above), 1920 x 1123 each","scaleRef":"each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture (.cache/batch9/vortex-sport-cantilever-30mm-mount/camfit.py: the outline of the daylight seen through each bore, which is the near rim on one side and the far rim on the other; the split lines on the seen end face, on the bore's far wall and on the near side flat, all in the plane of the rings' axis; 1.2 to 1.6 px on the rims, 0.1 to 1.3 px on the lines; the cameras 36.6 and 37.0 in from the mount, 45 and 43 degrees off its axis, 15 and 18 degrees up)","method":"the distance between each bore's two rims, a free parameter of each camera's fit: 0.730 and 0.739. It moves with the spacing given to the fit, 0.021 for each tenth of an inch","via":"harvest"}},{"id":"side","value":0.738,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount 910667d8ac8f (Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123)","scaleRef":"the receiver's rail slots (std.picatinny.slot_pitch), by the daylight through seven of them behind and under the mount, their centres at columns 666.52, 690.76, 714.94, 739.29, 811.72, 884.32 and 957.00 (slots -7 to -4, -1, 2 and 5 from the rear lug's): 24.207 px a slot, 61.44 px/in, no centre more than 0.15 px off the line; the rail's top is the teeth's top edge, row 417.4 under the mount (tilted 0.25 degrees with the picture)","method":"each cap over the tube: 43.9 px for the rear ring (0.714) and 46.8 px for the front (0.762): their mean","via":"harvest"}}],"adopt":{"from":"obliques","reason":"The bore's own two rims, in two pictures; the side view's two rings read 0.05 apart and their mean agrees."}},"mount_length":{"label":"Clamp length along the rail (at its foot)","kind":"length","measurements":[{"id":"side","value":3.148,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount 910667d8ac8f (Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123)","scaleRef":"the receiver's rail slots (std.picatinny.slot_pitch), by the daylight through seven of them behind and under the mount, their centres at columns 666.52, 690.76, 714.94, 739.29, 811.72, 884.32 and 957.00 (slots -7 to -4, -1, 2 and 5 from the rear lug's): 24.207 px a slot, 61.44 px/in, no centre more than 0.15 px off the line; the rail's top is the teeth's top edge, row 417.4 under the mount (tilted 0.25 degrees with the picture)","method":"from the rear fixed jaw's rear end (the base's rear end, column 753.6) to the front fixed jaw's front end (the lit edge at column 947): 193.4 px","via":"harvest"}}]},"overall_length":{"label":"Overall length, the base's rear end to the front ring's front face","kind":"length","measurements":[{"id":"side","value":5.345,"unit":"in","pm":0.07,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount 910667d8ac8f (Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123)","scaleRef":"the receiver's rail slots (std.picatinny.slot_pitch), by the daylight through seven of them behind and under the mount, their centres at columns 666.52, 690.76, 714.94, 739.29, 811.72, 884.32 and 957.00 (slots -7 to -4, -1, 2 and 5 from the rear lug's): 24.207 px a slot, 61.44 px/in, no centre more than 0.15 px off the line; the rail's top is the teeth's top edge, row 417.4 under the mount (tilted 0.25 degrees with the picture)","method":"column 753.6 to the front ring's lower half's front face, 1082: 328.4 px","via":"harvest"}}]},"clamp_rear_reach":{"label":"The base's rear end behind the rear recoil lug","kind":"length","measurements":[{"id":"side","value":1.34,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount 910667d8ac8f (Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123)","scaleRef":"the receiver's rail slots (std.picatinny.slot_pitch), by the daylight through seven of them behind and under the mount, their centres at columns 666.52, 690.76, 714.94, 739.29, 811.72, 884.32 and 957.00 (slots -7 to -4, -1, 2 and 5 from the rear lug's): 24.207 px a slot, 61.44 px/in, no centre more than 0.15 px off the line; the rail's top is the teeth's top edge, row 417.4 under the mount (tilted 0.25 degrees with the picture)","method":"the base's rear end, column 753.6 on four rows, to the rear lug's middle, 835.95","via":"harvest"}},{"id":"camera","value":1.342,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount a1e22b679294 (Vortex, ..._30mm_fr_w.jpg: the mount alone from the front right and above) and 22565a4f580e (..._30mm_bl_w.jpg: from the rear left and above), 1920 x 1123 each","scaleRef":"each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture (.cache/batch9/vortex-sport-cantilever-30mm-mount/camfit.py: the outline of the daylight seen through each bore, which is the near rim on one side and the far rim on the other; the split lines on the seen end face, on the bore's far wall and on the near side flat, all in the plane of the rings' axis; 1.2 to 1.6 px on the rims, 0.1 to 1.3 px on the lines; the cameras 36.6 and 37.0 in from the mount, 45 and 43 degrees off its axis, 15 and 18 degrees up)","method":"picture `fr`: the rear jaw's rear outer top corner, on the plane of the base's top (base_top_y): 1.528 in behind the rear ring's middle, less ring_rear_x","via":"harvest"}}],"adopt":{"from":"side","reason":"The square view; the camera fitted to the oblique, scaled by the bore, lands on it."}},"clamp_front_reach":{"label":"The front jaw's front end ahead of the rear recoil lug","kind":"length","measurements":[{"id":"side","value":1.807,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount 910667d8ac8f (Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123)","scaleRef":"the receiver's rail slots (std.picatinny.slot_pitch), by the daylight through seven of them behind and under the mount, their centres at columns 666.52, 690.76, 714.94, 739.29, 811.72, 884.32 and 957.00 (slots -7 to -4, -1, 2 and 5 from the rear lug's): 24.207 px a slot, 61.44 px/in, no centre more than 0.15 px off the line; the rail's top is the teeth's top edge, row 417.4 under the mount (tilted 0.25 degrees with the picture)","method":"the front fixed jaw's front end, the lit edge at column 947 on rows 402 to 418, less 835.95","via":"harvest"}}]},"rear_jaw_length":{"label":"Rear fixed jaw (right side), its length along the rail","kind":"length","measurements":[{"id":"side","value":0.763,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount 910667d8ac8f (Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123)","scaleRef":"the receiver's rail slots (std.picatinny.slot_pitch), by the daylight through seven of them behind and under the mount, their centres at columns 666.52, 690.76, 714.94, 739.29, 811.72, 884.32 and 957.00 (slots -7 to -4, -1, 2 and 5 from the rear lug's): 24.207 px a slot, 61.44 px/in, no centre more than 0.15 px off the line; the rail's top is the teeth's top edge, row 417.4 under the mount (tilted 0.25 degrees with the picture)","method":"columns 753.6 to 800.5 (its front edge is a lit line at column 800)","via":"harvest"}}]},"front_jaw_length":{"label":"Front fixed jaw (right side), its length along the rail","kind":"length","measurements":[{"id":"side","value":0.822,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount 910667d8ac8f (Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123)","scaleRef":"the receiver's rail slots (std.picatinny.slot_pitch), by the daylight through seven of them behind and under the mount, their centres at columns 666.52, 690.76, 714.94, 739.29, 811.72, 884.32 and 957.00 (slots -7 to -4, -1, 2 and 5 from the rear lug's): 24.207 px a slot, 61.44 px/in, no centre more than 0.15 px off the line; the rail's top is the teeth's top edge, row 417.4 under the mount (tilted 0.25 degrees with the picture)","method":"the lit edges at columns 896.5 and 947","via":"harvest"}}]},"lug_length":{"label":"A recoil lug, along the rail","kind":"length","measurements":[{"id":"side","value":0.192,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount 910667d8ac8f (Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123)","scaleRef":"the receiver's rail slots (std.picatinny.slot_pitch), by the daylight through seven of them behind and under the mount, their centres at columns 666.52, 690.76, 714.94, 739.29, 811.72, 884.32 and 957.00 (slots -7 to -4, -1, 2 and 5 from the rear lug's): 24.207 px a slot, 61.44 px/in, no centre more than 0.15 px off the line; the rail's top is the teeth's top edge, row 417.4 under the mount (tilted 0.25 degrees with the picture)","method":"the rear lug, dark between two slivers of daylight in its slot: columns 830.06 to 841.89","via":"harvest"}}],"note":"Each lies in a slot (0.206 wide): the picture has a sliver of daylight ahead of each and behind the rear one. The camera fitted to picture `fr` reads the two 0.18 long and 0.38 apart, the rear one's middle 0.03 behind the origin."},"lug_spacing":{"label":"The two recoil lugs, middle to middle","kind":"length","measurements":[{"id":"slots","value":0.394,"unit":"in","source":{"type":"derived","expr":"{std.picatinny.slot_pitch}","via":"harvest"}}],"note":"They lie in neighbouring slots of the receiver's rail in the maker's picture: one pitch, which the picture reads as 0.39 (the lugs' front edges 23.99 px apart, the slots 24.21)."},"lug_half_width":{"label":"A recoil lug's end, out from the mount's middle","kind":"length","measurements":[{"id":"camera","value":0.27,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount a1e22b679294 (Vortex, ..._30mm_fr_w.jpg: the mount alone from the front right and above) and 22565a4f580e (..._30mm_bl_w.jpg: from the rear left and above), 1920 x 1123 each","scaleRef":"each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture (.cache/batch9/vortex-sport-cantilever-30mm-mount/camfit.py: the outline of the daylight seen through each bore, which is the near rim on one side and the far rim on the other; the split lines on the seen end face, on the bore's far wall and on the near side flat, all in the plane of the rings' axis; 1.2 to 1.6 px on the rims, 0.1 to 1.3 px on the lines; the cameras 36.6 and 37.0 in from the mount, 45 and 43 degrees off its axis, 15 and 18 degrees up)","method":"picture `fr`: the four upper outer corners of the two lugs where they leave the base's underside, on the plane of the rail's top: 0.287, 0.246, 0.272, 0.247","via":"harvest"}}],"note":"Read on the right; the picture from the rear left shows lugs in the same notch on the left, and the two sides are drawn alike, each lug one bar across."},"base_middle_half_width":{"label":"The base between the clamp blocks (the wall the maker's mark is on), out from the mount's middle","kind":"length","measurements":[{"id":"lugs","value":0.27,"unit":"in","pm":0.03,"source":{"type":"derived","expr":"{.lug_half_width}","via":"harvest"}}],"note":"The lugs' ends read where they leave the base's underside (lug_half_width), so the base there is at least as wide; in `fr` the lugs' end faces stand in line with the wall over them, a little in. Drawn as wide as the lugs, both sides alike, from the rail's top to the base's top (base_top_y), between the two blocks; where the wall rises into the rear ring's stem it is the stem's lean."},"base_top_y":{"label":"The base's top behind the rear ring, above the rail's top","kind":"length","measurements":[{"id":"side","value":0.316,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount 910667d8ac8f (Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123)","scaleRef":"the receiver's rail slots (std.picatinny.slot_pitch), by the daylight through seven of them behind and under the mount, their centres at columns 666.52, 690.76, 714.94, 739.29, 811.72, 884.32 and 957.00 (slots -7 to -4, -1, 2 and 5 from the rear lug's): 24.207 px a slot, 61.44 px/in, no centre more than 0.15 px off the line; the rail's top is the teeth's top edge, row 417.4 under the mount (tilted 0.25 degrees with the picture)","method":"the silhouette's top edge over columns 754 to 791, row 398.0, above the rail's top at 417.4","via":"harvest"}},{"id":"camera","value":0.31,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount a1e22b679294 (Vortex, ..._30mm_fr_w.jpg: the mount alone from the front right and above) and 22565a4f580e (..._30mm_bl_w.jpg: from the rear left and above), 1920 x 1123 each","scaleRef":"each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture (.cache/batch9/vortex-sport-cantilever-30mm-mount/camfit.py: the outline of the daylight seen through each bore, which is the near rim on one side and the far rim on the other; the split lines on the seen end face, on the bore's far wall and on the near side flat, all in the plane of the rings' axis; 1.2 to 1.6 px on the rims, 0.1 to 1.3 px on the lines; the cameras 36.6 and 37.0 in from the mount, 45 and 43 degrees off its axis, 15 and 18 degrees up)","method":"picture `bl`: the two upper corners of the base's rear end face, on the plane of the base's rear end (clamp_rear_reach): 0.315 and 0.308 above the rail's top as 1.50 below the rings' axis","via":"harvest"}}],"adopt":{"from":"side","reason":"The square view; the oblique's camera agrees."}},"jaw_bottom_below_rail_top":{"label":"The fixed jaws' feet below the rail's top","kind":"length","measurements":[{"id":"side","value":0.233,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount 910667d8ac8f (Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123)","scaleRef":"the receiver's rail slots (std.picatinny.slot_pitch), by the daylight through seven of them behind and under the mount, their centres at columns 666.52, 690.76, 714.94, 739.29, 811.72, 884.32 and 957.00 (slots -7 to -4, -1, 2 and 5 from the rear lug's): 24.207 px a slot, 61.44 px/in, no centre more than 0.15 px off the line; the rail's top is the teeth's top edge, row 417.4 under the mount (tilted 0.25 degrees with the picture)","method":"the lit chamfer along both jaws' feet ends at row 431.7; the rail's top is 417.4","via":"harvest"}}]},"front_jaw_top_y":{"label":"The front fixed jaw's top, above the rail's top","kind":"length","measurements":[{"id":"side","value":0.259,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount 910667d8ac8f (Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123)","scaleRef":"the receiver's rail slots (std.picatinny.slot_pitch), by the daylight through seven of them behind and under the mount, their centres at columns 666.52, 690.76, 714.94, 739.29, 811.72, 884.32 and 957.00 (slots -7 to -4, -1, 2 and 5 from the rear lug's): 24.207 px a slot, 61.44 px/in, no centre more than 0.15 px off the line; the rail's top is the teeth's top edge, row 417.4 under the mount (tilted 0.25 degrees with the picture)","method":"the dark line over columns 899 to 941 at row 401.5","via":"harvest"}}],"note":"The front jaw's block stands out of the base's side under the arm: a dark line along its top at this height in the side view, with the arm's side above it."},"ring_top_above_axis":{"label":"A ring's top flat above the rings' axis","kind":"length","measurements":[{"id":"side","value":0.689,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount 910667d8ac8f (Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123)","scaleRef":"the receiver's rail slots (std.picatinny.slot_pitch), by the daylight through seven of them behind and under the mount, their centres at columns 666.52, 690.76, 714.94, 739.29, 811.72, 884.32 and 957.00 (slots -7 to -4, -1, 2 and 5 from the rear lug's): 24.207 px a slot, 61.44 px/in, no centre more than 0.15 px off the line; the rail's top is the teeth's top edge, row 417.4 under the mount (tilted 0.25 degrees with the picture)","method":"the rear ring's cap's top edge, row 284.55, above the tube's centre line there (the middle of its two edges, row 326.85): 42.3 px; the front ring's the same within 0.3 px","via":"harvest"}},{"id":"obliques","value":0.677,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount a1e22b679294 (Vortex, ..._30mm_fr_w.jpg: the mount alone from the front right and above) and 22565a4f580e (..._30mm_bl_w.jpg: from the rear left and above), 1920 x 1123 each","scaleRef":"each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture (.cache/batch9/vortex-sport-cantilever-30mm-mount/camfit.py: the outline of the daylight seen through each bore, which is the near rim on one side and the far rim on the other; the split lines on the seen end face, on the bore's far wall and on the near side flat, all in the plane of the rings' axis; 1.2 to 1.6 px on the rims, 0.1 to 1.3 px on the lines; the cameras 36.6 and 37.0 in from the mount, 45 and 43 degrees off its axis, 15 and 18 degrees up)","method":"picture `fr`, the rear ring's front face: its top edge stands 21.4 px over the bore's top on the line up the middle of the face, where the camera has 1500 px/in at the crop's scale of five: 0.071 in, and the flat is a bevel of some 0.015 above the face's edge. (The camera's own height for that edge is 0.64: its bore's top is 6 px above the picture's there, a bias the fit's rims leave up and down.)","via":"harvest"}}],"adopt":{"from":"side","reason":"A square view of the cap against the centre line of the tube it holds; the oblique's reading rests on a pick of the bevel and agrees within a hundredth."},"note":"Counted in the side view from the tube's own upper edge instead (the cap stands 6.85 px over it) it would be 0.702; but the black tube's edges read 0.7 px in on each side there (71.2 px across for 72.6), and from the tube's centre line the two pictures through their cameras agree with it: the ledger's figures drawn back over both (check-a1e2-crop.png, check-2256-crop.png) have each end face's top edge, a bevel under the flat, 0.03 under a top drawn at 0.70."},"ring_width":{"label":"Rings, across their side flats","kind":"length","measurements":[{"id":"obliques","value":1.85,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount a1e22b679294 (Vortex, ..._30mm_fr_w.jpg: the mount alone from the front right and above) and 22565a4f580e (..._30mm_bl_w.jpg: from the rear left and above), 1920 x 1123 each","scaleRef":"each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture (.cache/batch9/vortex-sport-cantilever-30mm-mount/camfit.py: the outline of the daylight seen through each bore, which is the near rim on one side and the far rim on the other; the split lines on the seen end face, on the bore's far wall and on the near side flat, all in the plane of the rings' axis; 1.2 to 1.6 px on the rims, 0.1 to 1.3 px on the lines; the cameras 36.6 and 37.0 in from the mount, 45 and 43 degrees off its axis, 15 and 18 degrees up)","method":"the split line where it runs along the near side flat, which lies in the plane of the rings' axis: 0.926 and 0.929 in from the mount's middle (picture `fr`, front and rear ring), 0.924 and 0.920 (picture `bl`); twice their mean. It doesn't move with the rings' spacing (0.001 over a tenth of an inch)","via":"harvest"}}],"note":"Wider than tall: the cap screws stand beside the tube. The end faces' own edges read 0.90 out (a bevel of 0.02 round each face)."},"ring_top_flat_width":{"label":"Rings, their top flat across","kind":"length","measurements":[{"id":"obliques","value":0.76,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount a1e22b679294 (Vortex, ..._30mm_fr_w.jpg: the mount alone from the front right and above) and 22565a4f580e (..._30mm_bl_w.jpg: from the rear left and above), 1920 x 1123 each","scaleRef":"each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture (.cache/batch9/vortex-sport-cantilever-30mm-mount/camfit.py: the outline of the daylight seen through each bore, which is the near rim on one side and the far rim on the other; the split lines on the seen end face, on the bore's far wall and on the near side flat, all in the plane of the rings' axis; 1.2 to 1.6 px on the rims, 0.1 to 1.3 px on the lines; the cameras 36.6 and 37.0 in from the mount, 45 and 43 degrees off its axis, 15 and 18 degrees up)","method":"picture `fr`: the two ends of each ring's front face's top edge, on that face's plane: 0.415 and -0.374 (rear ring), 0.384 and -0.348 (front ring) from the middle","via":"harvest"}}]},"ring_side_flat_above_split":{"label":"Rings, the side flat's height above the split (the cap's)","kind":"length","measurements":[{"id":"obliques","value":0.15,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount a1e22b679294 (Vortex, ..._30mm_fr_w.jpg: the mount alone from the front right and above) and 22565a4f580e (..._30mm_bl_w.jpg: from the rear left and above), 1920 x 1123 each","scaleRef":"each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture (.cache/batch9/vortex-sport-cantilever-30mm-mount/camfit.py: the outline of the daylight seen through each bore, which is the near rim on one side and the far rim on the other; the split lines on the seen end face, on the bore's far wall and on the near side flat, all in the plane of the rings' axis; 1.2 to 1.6 px on the rims, 0.1 to 1.3 px on the lines; the cameras 36.6 and 37.0 in from the mount, 45 and 43 degrees off its axis, 15 and 18 degrees up)","method":"picture `fr`: where each ring's front face's edge turns from the side flat to the upper chamfer, on that face's plane: 0.160 and 0.158 (rear ring, far and near side), 0.156 and 0.126 (front ring)","via":"harvest"}}]},"ring_side_flat_below_split":{"label":"Rings, the side flat's height below the split (the lower half's)","kind":"length","measurements":[{"id":"obliques","value":0.115,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount a1e22b679294 (Vortex, ..._30mm_fr_w.jpg: the mount alone from the front right and above) and 22565a4f580e (..._30mm_bl_w.jpg: from the rear left and above), 1920 x 1123 each","scaleRef":"each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture (.cache/batch9/vortex-sport-cantilever-30mm-mount/camfit.py: the outline of the daylight seen through each bore, which is the near rim on one side and the far rim on the other; the split lines on the seen end face, on the bore's far wall and on the near side flat, all in the plane of the rings' axis; 1.2 to 1.6 px on the rims, 0.1 to 1.3 px on the lines; the cameras 36.6 and 37.0 in from the mount, 45 and 43 degrees off its axis, 15 and 18 degrees up)","method":"picture `fr`: where each front face's edge turns from the side flat to the lower chamfer: 0.117 and 0.098 (rear ring), 0.137 and 0.106 (front ring)","via":"harvest"}}]},"ring_foot_below_axis":{"label":"Rings, where the lower chamfers meet the stem, below the rings' axis","kind":"length","measurements":[{"id":"obliques","value":0.745,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount a1e22b679294 (Vortex, ..._30mm_fr_w.jpg: the mount alone from the front right and above) and 22565a4f580e (..._30mm_bl_w.jpg: from the rear left and above), 1920 x 1123 each","scaleRef":"each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture (.cache/batch9/vortex-sport-cantilever-30mm-mount/camfit.py: the outline of the daylight seen through each bore, which is the near rim on one side and the far rim on the other; the split lines on the seen end face, on the bore's far wall and on the near side flat, all in the plane of the rings' axis; 1.2 to 1.6 px on the rims, 0.1 to 1.3 px on the lines; the cameras 36.6 and 37.0 in from the mount, 45 and 43 degrees off its axis, 15 and 18 degrees up)","method":"picture `fr`: the foot of each lower chamfer on the ring's front face: 0.721 and 0.754 (rear ring), 0.793 and 0.712 (front ring)","via":"harvest"}}]},"stem_width":{"label":"Each ring's foot, where its two lower chamfers end, across","kind":"length","measurements":[{"id":"obliques","value":0.81,"unit":"in","pm":0.05,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount a1e22b679294 (Vortex, ..._30mm_fr_w.jpg: the mount alone from the front right and above) and 22565a4f580e (..._30mm_bl_w.jpg: from the rear left and above), 1920 x 1123 each","scaleRef":"each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture (.cache/batch9/vortex-sport-cantilever-30mm-mount/camfit.py: the outline of the daylight seen through each bore, which is the near rim on one side and the far rim on the other; the split lines on the seen end face, on the bore's far wall and on the near side flat, all in the plane of the rings' axis; 1.2 to 1.6 px on the rims, 0.1 to 1.3 px on the lines; the cameras 36.6 and 37.0 in from the mount, 45 and 43 degrees off its axis, 15 and 18 degrees up)","method":"picture `fr`: the feet of the two lower chamfers on each ring's front face: 0.435 and -0.374 from the middle (rear ring), 0.377 and -0.429 (front ring): 0.809 and 0.806 across","via":"harvest"}}]},"arm_width":{"label":"The arm between the rings, across its walls (below its top's chamfers)","kind":"length","measurements":[{"id":"obliques","value":0.42,"unit":"in","pm":0.08,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount a1e22b679294 (Vortex, ..._30mm_fr_w.jpg: the mount alone from the front right and above) and 22565a4f580e (..._30mm_bl_w.jpg: from the rear left and above), 1920 x 1123 each","scaleRef":"each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture (.cache/batch9/vortex-sport-cantilever-30mm-mount/camfit.py: the outline of the daylight seen through each bore, which is the near rim on one side and the far rim on the other; the split lines on the seen end face, on the bore's far wall and on the near side flat, all in the plane of the rings' axis; 1.2 to 1.6 px on the rims, 0.1 to 1.3 px on the lines; the cameras 36.6 and 37.0 in from the mount, 45 and 43 degrees off its axis, 15 and 18 degrees up)","method":"both pictures, each against a grid of points on the plane of the arm's top (0.391 above the rail, as the side view has it) drawn through its camera (.cache/batch9/vortex-sport-cantilever-30mm-mount/grid.py), at 1.4 and 1.8 in ahead of the rear lug: the top flat's right edge is 0.235 out in `fr` and 0.25 in `bl`; its left edge 0.02 left of the middle in `bl` (in `fr` the left chamfer hides it); the lit chamfer under that edge ends on the left wall, which the same grid has between 0.08 and 0.19 left of the middle, by how far the chamfer drops (0.08 to 0.03); the right wall is a narrow chamfer outside the flat's edge, about 0.27. From 0.35 to 0.46 across","via":"harvest"},"note":"Read by eye against a grid. Its right wall, 0.27, is where the narrow chamfer's foot falls on the plane of the top in `fr` (the ray from 15 degrees up crosses that plane 0.05 further out than the foot is): the lit band ends at 0.265 to 0.27 on that plane at every station, and down the chamfer itself it ends 0.025 out from the flat's edge. Its 0.25 in `bl` is where the arm's silhouette meets the white ground, which the tones put at 0.18 to 0.20 (arm_top_right_z)."},{"id":"edges","value":0.322,"unit":"in","pm":0.045,"source":{"type":"derived","expr":"({.arm_top_right_z} + {.arm_chamfer_right}) - ({.arm_top_left_z} - {.arm_chamfer_left})","via":"harvest"},"note":"The flat's two edges and the two chamfers, each read on the pictures' tones along lines across the arm through the cameras (2026-10-19)."}],"adopt":{"from":"edges","reason":"Each edge read where the picture's tone changes along a line cast across the arm through its camera, at three stations, rather than against a grid by eye; the first reading's right wall was the chamfer's foot as it falls on the plane of the top, 0.05 further out than the foot. Kept beside it."},"note":"Much narrower than the rings' feet: the stems lean in to it. Its top is a flat with a chamfer down each side, the left one the broader, and the arm is not about the mount's middle: its walls are 0.11 in left and 0.22 right of it (arm_top_left_z, arm_top_right_z and the two chamfers, read again on 2026-10-19 through the same two cameras). The right-hand ends of the two recoil lugs read 0.27 out (lug_half_width): the base under the arm is wider than the arm there, which the maker's mark is on."},"arm_top_left_z":{"label":"The arm's top flat, its left edge from the mount's middle (negative: to the left)","kind":"length","measurements":[{"id":"bl","value":-0.032,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount a1e22b679294 (Vortex, ..._30mm_fr_w.jpg: the mount alone from the front right and above) and 22565a4f580e (..._30mm_bl_w.jpg: from the rear left and above), 1920 x 1123 each","scaleRef":"each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture (.cache/batch9/vortex-sport-cantilever-30mm-mount/camfit.py: the outline of the daylight seen through each bore, which is the near rim on one side and the far rim on the other; the split lines on the seen end face, on the bore's far wall and on the near side flat, all in the plane of the rings' axis; 1.2 to 1.6 px on the rims, 0.1 to 1.3 px on the lines; the cameras 36.6 and 37.0 in from the mount, 45 and 43 degrees off its axis, 15 and 18 degrees up)","method":"picture `bl`, through its camera: the tone along a line across the arm on the plane of its top (0.395 above the rail) at 1.3, 1.6 and 1.9 in ahead of the rear lug steps from the left chamfer's (32 to 53 of 255) to the flat's (59 to 68) at -0.035, -0.035 and -0.025 (.cache/night-2026-10-19/detail/vortex-sport-cantilever-30mm-mount/arm.py)","via":"harvest"}}]},"arm_top_right_z":{"label":"The arm's top flat, its right edge from the mount's middle","kind":"length","measurements":[{"id":"bl","value":0.19,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount a1e22b679294 (Vortex, ..._30mm_fr_w.jpg: the mount alone from the front right and above) and 22565a4f580e (..._30mm_bl_w.jpg: from the rear left and above), 1920 x 1123 each","scaleRef":"each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture (.cache/batch9/vortex-sport-cantilever-30mm-mount/camfit.py: the outline of the daylight seen through each bore, which is the near rim on one side and the far rim on the other; the split lines on the seen end face, on the bore's far wall and on the near side flat, all in the plane of the rings' axis; 1.2 to 1.6 px on the rims, 0.1 to 1.3 px on the lines; the cameras 36.6 and 37.0 in from the mount, 45 and 43 degrees off its axis, 15 and 18 degrees up)","method":"picture `bl`, through its camera: on the plane of the arm's top the flat's tone (64 to 79) meets the white ground beyond the arm half-way at 0.20 (1.6 in ahead of the rear lug) and 0.183 (1.9 in): from the rear left and 18 degrees up, the right chamfer faces away and the silhouette is the flat's edge","via":"harvest"}}]},"arm_chamfer_left":{"label":"The arm's left chamfer, its width across (from the flat's edge out to the left wall)","kind":"length","measurements":[{"id":"bl","value":0.075,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount a1e22b679294 (Vortex, ..._30mm_fr_w.jpg: the mount alone from the front right and above) and 22565a4f580e (..._30mm_bl_w.jpg: from the rear left and above), 1920 x 1123 each","scaleRef":"each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture (.cache/batch9/vortex-sport-cantilever-30mm-mount/camfit.py: the outline of the daylight seen through each bore, which is the near rim on one side and the far rim on the other; the split lines on the seen end face, on the bore's far wall and on the near side flat, all in the plane of the rings' axis; 1.2 to 1.6 px on the rims, 0.1 to 1.3 px on the lines; the cameras 36.6 and 37.0 in from the mount, 45 and 43 degrees off its axis, 15 and 18 degrees up)","method":"picture `bl`, through its camera: down a 45 degree plane from the flat's left edge (-0.035) the chamfer's tone (37 to 52) holds to 0.07 out and drops to 21 at 0.08, at 1.3, 1.6 and 1.9 in ahead of the rear lug alike","via":"harvest"}}],"note":"Read as a 45 degree chamfer: its drop is taken to be its width (an assumption for the drawing: one picture sees the left side from above, and its camera gives a line of widths and drops, not one). Drawn so."},"arm_chamfer_right":{"label":"The arm's right chamfer, its width across (from the flat's edge out to the right wall)","kind":"length","measurements":[{"id":"fr","value":0.025,"unit":"in","pm":0.01,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount a1e22b679294 (Vortex, ..._30mm_fr_w.jpg: the mount alone from the front right and above) and 22565a4f580e (..._30mm_bl_w.jpg: from the rear left and above), 1920 x 1123 each","scaleRef":"each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture (.cache/batch9/vortex-sport-cantilever-30mm-mount/camfit.py: the outline of the daylight seen through each bore, which is the near rim on one side and the far rim on the other; the split lines on the seen end face, on the bore's far wall and on the near side flat, all in the plane of the rings' axis; 1.2 to 1.6 px on the rims, 0.1 to 1.3 px on the lines; the cameras 36.6 and 37.0 in from the mount, 45 and 43 degrees off its axis, 15 and 18 degrees up)","method":"picture `fr`, through its camera: down a 45 degree plane from the flat's right edge (0.195) the lit tone (58 to 79) holds to 0.02 out and drops to 21 to 24 at 0.03, at 1.3, 1.6 and 1.9 in ahead of the rear lug alike. On the plane of the top the lit band ends at 0.265 to 0.27, where a ray from 15 degrees up through a foot 0.025 down and 0.025 out falls","via":"harvest"}}],"note":"Read as a 45 degree chamfer, as the left one (assumed). The narrow one: the left is three times as broad."},"base_right_z":{"label":"The fixed jaws' outer face, out from the mount's middle (right side)","kind":"length","measurements":[{"id":"obliques","value":0.637,"unit":"in","pm":0.015,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount a1e22b679294 (Vortex, ..._30mm_fr_w.jpg: the mount alone from the front right and above) and 22565a4f580e (..._30mm_bl_w.jpg: from the rear left and above), 1920 x 1123 each","scaleRef":"each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture (.cache/batch9/vortex-sport-cantilever-30mm-mount/camfit.py: the outline of the daylight seen through each bore, which is the near rim on one side and the far rim on the other; the split lines on the seen end face, on the bore's far wall and on the near side flat, all in the plane of the rings' axis; 1.2 to 1.6 px on the rims, 0.1 to 1.3 px on the lines; the cameras 36.6 and 37.0 in from the mount, 45 and 43 degrees off its axis, 15 and 18 degrees up)","method":"picture `fr`: the rear jaw's two upper outer corners and the front jaw's rear one, on the planes of their tops: 0.640, 0.625, 0.642; picture `bl`: the right-hand corners of the base's rear end face, on its plane: 0.637 and 0.643","via":"harvest"}}]},"base_left_z":{"label":"The base's left side, where the clamp blocks bear, out from the mount's middle","kind":"length","measurements":[{"id":"obliques","value":0.43,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount a1e22b679294 (Vortex, ..._30mm_fr_w.jpg: the mount alone from the front right and above) and 22565a4f580e (..._30mm_bl_w.jpg: from the rear left and above), 1920 x 1123 each","scaleRef":"each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture (.cache/batch9/vortex-sport-cantilever-30mm-mount/camfit.py: the outline of the daylight seen through each bore, which is the near rim on one side and the far rim on the other; the split lines on the seen end face, on the bore's far wall and on the near side flat, all in the plane of the rings' axis; 1.2 to 1.6 px on the rims, 0.1 to 1.3 px on the lines; the cameras 36.6 and 37.0 in from the mount, 45 and 43 degrees off its axis, 15 and 18 degrees up)","method":"picture `bl`: the upper left corner of the base's rear end face, on its plane: 0.429; the rear clamp's top face's inner front corner on the plane of its top reads 0.451","via":"harvest"}}],"note":"A hundredth outside the rail's own widest (0.4175): the two clamp blocks stand against it."},"clamp_outer_z":{"label":"The clamp blocks' outer face, out from the mount's middle (left side)","kind":"length","measurements":[{"id":"obliques","value":0.625,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount a1e22b679294 (Vortex, ..._30mm_fr_w.jpg: the mount alone from the front right and above) and 22565a4f580e (..._30mm_bl_w.jpg: from the rear left and above), 1920 x 1123 each","scaleRef":"each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture (.cache/batch9/vortex-sport-cantilever-30mm-mount/camfit.py: the outline of the daylight seen through each bore, which is the near rim on one side and the far rim on the other; the split lines on the seen end face, on the bore's far wall and on the near side flat, all in the plane of the rings' axis; 1.2 to 1.6 px on the rims, 0.1 to 1.3 px on the lines; the cameras 36.6 and 37.0 in from the mount, 45 and 43 degrees off its axis, 15 and 18 degrees up)","method":"picture `bl`: the front corners of both blocks' outer faces, each on the plane of the x the side view has that end of its jaw at: 0.627, 0.627, 0.610, 0.631","via":"harvest"}}]},"clamp_length":{"label":"A clamp block, its length along the rail","kind":"length","measurements":[{"id":"obliques","value":0.73,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount a1e22b679294 (Vortex, ..._30mm_fr_w.jpg: the mount alone from the front right and above) and 22565a4f580e (..._30mm_bl_w.jpg: from the rear left and above), 1920 x 1123 each","scaleRef":"each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture (.cache/batch9/vortex-sport-cantilever-30mm-mount/camfit.py: the outline of the daylight seen through each bore, which is the near rim on one side and the far rim on the other; the split lines on the seen end face, on the bore's far wall and on the near side flat, all in the plane of the rings' axis; 1.2 to 1.6 px on the rims, 0.1 to 1.3 px on the lines; the cameras 36.6 and 37.0 in from the mount, 45 and 43 degrees off its axis, 15 and 18 degrees up)","method":"picture `bl`: each block's outer face's two upper corners on the plane of that face (clamp_outer_z): the rear block from 1.296 to 0.573 behind the rear lug (0.723), the front one from 1.051 to 1.791 ahead of it (0.740)","via":"harvest"}}]},"rear_clamp_front_x":{"label":"The rear clamp block's front end, behind the rear recoil lug","kind":"length","measurements":[{"id":"obliques","value":0.573,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount a1e22b679294 (Vortex, ..._30mm_fr_w.jpg: the mount alone from the front right and above) and 22565a4f580e (..._30mm_bl_w.jpg: from the rear left and above), 1920 x 1123 each","scaleRef":"each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture (.cache/batch9/vortex-sport-cantilever-30mm-mount/camfit.py: the outline of the daylight seen through each bore, which is the near rim on one side and the far rim on the other; the split lines on the seen end face, on the bore's far wall and on the near side flat, all in the plane of the rings' axis; 1.2 to 1.6 px on the rims, 0.1 to 1.3 px on the lines; the cameras 36.6 and 37.0 in from the mount, 45 and 43 degrees off its axis, 15 and 18 degrees up)","method":"picture `bl`: its outer face's upper front corner on the plane of that face; the right side's rear jaw ends 0.577 behind the lug in the side view","via":"harvest"}}]},"front_clamp_front_x":{"label":"The front clamp block's front end, ahead of the rear recoil lug","kind":"length","measurements":[{"id":"obliques","value":1.791,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount a1e22b679294 (Vortex, ..._30mm_fr_w.jpg: the mount alone from the front right and above) and 22565a4f580e (..._30mm_bl_w.jpg: from the rear left and above), 1920 x 1123 each","scaleRef":"each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture (.cache/batch9/vortex-sport-cantilever-30mm-mount/camfit.py: the outline of the daylight seen through each bore, which is the near rim on one side and the far rim on the other; the split lines on the seen end face, on the bore's far wall and on the near side flat, all in the plane of the rings' axis; 1.2 to 1.6 px on the rims, 0.1 to 1.3 px on the lines; the cameras 36.6 and 37.0 in from the mount, 45 and 43 degrees off its axis, 15 and 18 degrees up)","method":"picture `bl`: its outer face's upper front corner on the plane of that face; the right side's front jaw ends 1.807 ahead of the lug in the side view","via":"harvest"}}]},"clamp_top_y":{"label":"The clamp blocks' top, above the rail's top","kind":"length","measurements":[{"id":"obliques","value":0.305,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount a1e22b679294 (Vortex, ..._30mm_fr_w.jpg: the mount alone from the front right and above) and 22565a4f580e (..._30mm_bl_w.jpg: from the rear left and above), 1920 x 1123 each","scaleRef":"each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture (.cache/batch9/vortex-sport-cantilever-30mm-mount/camfit.py: the outline of the daylight seen through each bore, which is the near rim on one side and the far rim on the other; the split lines on the seen end face, on the bore's far wall and on the near side flat, all in the plane of the rings' axis; 1.2 to 1.6 px on the rims, 0.1 to 1.3 px on the lines; the cameras 36.6 and 37.0 in from the mount, 45 and 43 degrees off its axis, 15 and 18 degrees up)","method":"picture `bl`: the four upper corners of the two blocks' outer faces on the plane of those faces: 0.293, 0.315, 0.305, 0.320","via":"harvest"}}]},"clamp_face_below_rail_top":{"label":"The clamp blocks' outer face, its lower edge below the rail's top","kind":"length","measurements":[{"id":"obliques","value":0.065,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount a1e22b679294 (Vortex, ..._30mm_fr_w.jpg: the mount alone from the front right and above) and 22565a4f580e (..._30mm_bl_w.jpg: from the rear left and above), 1920 x 1123 each","scaleRef":"each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture (.cache/batch9/vortex-sport-cantilever-30mm-mount/camfit.py: the outline of the daylight seen through each bore, which is the near rim on one side and the far rim on the other; the split lines on the seen end face, on the bore's far wall and on the near side flat, all in the plane of the rings' axis; 1.2 to 1.6 px on the rims, 0.1 to 1.3 px on the lines; the cameras 36.6 and 37.0 in from the mount, 45 and 43 degrees off its axis, 15 and 18 degrees up)","method":"picture `bl`: the lower front corners of the two blocks' outer faces and the front block's rear one, on the plane of those faces: 0.074, 0.068, 0.053","via":"harvest"}}],"note":"Under it the block is rounded in toward its hook, whose foot is taken to be as low as the fixed jaws' (jaw_bottom_below_rail_top): the hook itself shows only at the rear block's end."},"clamp_screw_y":{"label":"The four base screws, above the rail's top","kind":"length","measurements":[{"id":"obliques","value":0.135,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount a1e22b679294 (Vortex, ..._30mm_fr_w.jpg: the mount alone from the front right and above) and 22565a4f580e (..._30mm_bl_w.jpg: from the rear left and above), 1920 x 1123 each","scaleRef":"each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture (.cache/batch9/vortex-sport-cantilever-30mm-mount/camfit.py: the outline of the daylight seen through each bore, which is the near rim on one side and the far rim on the other; the split lines on the seen end face, on the bore's far wall and on the near side flat, all in the plane of the rings' axis; 1.2 to 1.6 px on the rims, 0.1 to 1.3 px on the lines; the cameras 36.6 and 37.0 in from the mount, 45 and 43 degrees off its axis, 15 and 18 degrees up)","method":"picture `bl`: the rear block's two counterbores' middles on the plane of its outer face: 0.144 and 0.126","via":"harvest"}}],"note":"They run across the mount above the rail, from the clamp blocks into the base: no screw crosses the rail."},"clamp_screw_spacing":{"label":"A clamp block's two screws, apart","kind":"length","measurements":[{"id":"obliques","value":0.325,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount a1e22b679294 (Vortex, ..._30mm_fr_w.jpg: the mount alone from the front right and above) and 22565a4f580e (..._30mm_bl_w.jpg: from the rear left and above), 1920 x 1123 each","scaleRef":"each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture (.cache/batch9/vortex-sport-cantilever-30mm-mount/camfit.py: the outline of the daylight seen through each bore, which is the near rim on one side and the far rim on the other; the split lines on the seen end face, on the bore's far wall and on the near side flat, all in the plane of the rings' axis; 1.2 to 1.6 px on the rims, 0.1 to 1.3 px on the lines; the cameras 36.6 and 37.0 in from the mount, 45 and 43 degrees off its axis, 15 and 18 degrees up)","method":"picture `bl`: the rear block's two counterbores' middles on the plane of its outer face: 0.755 and 1.080 behind the rear lug","via":"harvest"}}]},"screw_counterbore_d":{"label":"A screw's counterbore, across","kind":"length","measurements":[{"id":"obliques","value":0.23,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount a1e22b679294 (Vortex, ..._30mm_fr_w.jpg: the mount alone from the front right and above) and 22565a4f580e (..._30mm_bl_w.jpg: from the rear left and above), 1920 x 1123 each","scaleRef":"each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture (.cache/batch9/vortex-sport-cantilever-30mm-mount/camfit.py: the outline of the daylight seen through each bore, which is the near rim on one side and the far rim on the other; the split lines on the seen end face, on the bore's far wall and on the near side flat, all in the plane of the rings' axis; 1.2 to 1.6 px on the rims, 0.1 to 1.3 px on the lines; the cameras 36.6 and 37.0 in from the mount, 45 and 43 degrees off its axis, 15 and 18 degrees up)","method":"picture `bl`: the rear block's two counterbores, 62 and 64 px tall where the camera has 271 px/in up and down","via":"harvest"}}],"note":"The same screw holds the ring caps and the clamps (Vortex: \"Commonality between fasteners and components for one-tool mounting\"; Torx T-25 for both)."},"screw_head_d":{"label":"A screw's head, across","kind":"length","measurements":[{"id":"obliques","value":0.21,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount a1e22b679294 (Vortex, ..._30mm_fr_w.jpg: the mount alone from the front right and above) and 22565a4f580e (..._30mm_bl_w.jpg: from the rear left and above), 1920 x 1123 each","scaleRef":"each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture (.cache/batch9/vortex-sport-cantilever-30mm-mount/camfit.py: the outline of the daylight seen through each bore, which is the near rim on one side and the far rim on the other; the split lines on the seen end face, on the bore's far wall and on the near side flat, all in the plane of the rings' axis; 1.2 to 1.6 px on the rims, 0.1 to 1.3 px on the lines; the cameras 36.6 and 37.0 in from the mount, 45 and 43 degrees off its axis, 15 and 18 degrees up)","method":"picture `bl`: the heads in the rear block's counterbores, about 50 px tall at 271 px/in (0.185); picture `fr`: a head in the front ring's cap, 58 px along the ring where the ring's 0.735 in is 188 px (0.23): their mean","via":"harvest"}}]},"cap_screw_z":{"label":"The ring caps' screws, out from the mount's middle","kind":"length","measurements":[{"id":"obliques","value":0.762,"unit":"in","pm":0.025,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount a1e22b679294 (Vortex, ..._30mm_fr_w.jpg: the mount alone from the front right and above) and 22565a4f580e (..._30mm_bl_w.jpg: from the rear left and above), 1920 x 1123 each","scaleRef":"each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture (.cache/batch9/vortex-sport-cantilever-30mm-mount/camfit.py: the outline of the daylight seen through each bore, which is the near rim on one side and the far rim on the other; the split lines on the seen end face, on the bore's far wall and on the near side flat, all in the plane of the rings' axis; 1.2 to 1.6 px on the rims, 0.1 to 1.3 px on the lines; the cameras 36.6 and 37.0 in from the mount, 45 and 43 degrees off its axis, 15 and 18 degrees up)","method":"picture `fr`: the two heads on the near side of each ring, taken to be level and even about the ring's middle and solved through the camera for how far out, how high and how far apart: 0.758 (rear ring, 6.5 px left over) and 0.767 (front ring, 2.0 px)","via":"harvest"}}],"note":"Midway between the bore's wall (0.591) and the side flat (0.925), where they have to be."},"cap_screw_spacing":{"label":"A ring cap's two screws on one side, apart","kind":"length","measurements":[{"id":"obliques","value":0.39,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount a1e22b679294 (Vortex, ..._30mm_fr_w.jpg: the mount alone from the front right and above) and 22565a4f580e (..._30mm_bl_w.jpg: from the rear left and above), 1920 x 1123 each","scaleRef":"each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture (.cache/batch9/vortex-sport-cantilever-30mm-mount/camfit.py: the outline of the daylight seen through each bore, which is the near rim on one side and the far rim on the other; the split lines on the seen end face, on the bore's far wall and on the near side flat, all in the plane of the rings' axis; 1.2 to 1.6 px on the rims, 0.1 to 1.3 px on the lines; the cameras 36.6 and 37.0 in from the mount, 45 and 43 degrees off its axis, 15 and 18 degrees up)","method":"picture `fr`, with cap_screw_z: 0.391 (rear ring) and 0.387 (front ring)","via":"harvest"}},{"id":"side","value":0.387,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount 910667d8ac8f (Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123)","scaleRef":"the receiver's rail slots (std.picatinny.slot_pitch), by the daylight through seven of them behind and under the mount, their centres at columns 666.52, 690.76, 714.94, 739.29, 811.72, 884.32 and 957.00 (slots -7 to -4, -1, 2 and 5 from the rear lug's): 24.207 px a slot, 61.44 px/in, no centre more than 0.15 px off the line; the rail's top is the teeth's top edge, row 417.4 under the mount (tilted 0.25 degrees with the picture)","method":"the two small dark windows in the rear ring's lower half, under its two screws, at columns 835.9 and 859.7","via":"harvest"}}],"adopt":{"from":"obliques","reason":"Read on the screws' own heads; the side view's two windows under them are the same distance apart."}},"cap_screw_head_above_axis":{"label":"The ring caps' screws, their heads' tops above the rings' axis","kind":"length","measurements":[{"id":"obliques","value":0.255,"unit":"in","pm":0.03,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount a1e22b679294 (Vortex, ..._30mm_fr_w.jpg: the mount alone from the front right and above) and 22565a4f580e (..._30mm_bl_w.jpg: from the rear left and above), 1920 x 1123 each","scaleRef":"each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture (.cache/batch9/vortex-sport-cantilever-30mm-mount/camfit.py: the outline of the daylight seen through each bore, which is the near rim on one side and the far rim on the other; the split lines on the seen end face, on the bore's far wall and on the near side flat, all in the plane of the rings' axis; 1.2 to 1.6 px on the rims, 0.1 to 1.3 px on the lines; the cameras 36.6 and 37.0 in from the mount, 45 and 43 degrees off its axis, 15 and 18 degrees up)","method":"picture `fr`, with cap_screw_z: 0.260 (rear ring) and 0.250 (front ring)","via":"harvest"}}]},"cap_pocket_d":{"label":"A ring cap's screw pocket, across","kind":"length","measurements":[{"id":"obliques","value":0.32,"unit":"in","pm":0.04,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount a1e22b679294 (Vortex, ..._30mm_fr_w.jpg: the mount alone from the front right and above) and 22565a4f580e (..._30mm_bl_w.jpg: from the rear left and above), 1920 x 1123 each","scaleRef":"each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture (.cache/batch9/vortex-sport-cantilever-30mm-mount/camfit.py: the outline of the daylight seen through each bore, which is the near rim on one side and the far rim on the other; the split lines on the seen end face, on the bore's far wall and on the near side flat, all in the plane of the rings' axis; 1.2 to 1.6 px on the rims, 0.1 to 1.3 px on the lines; the cameras 36.6 and 37.0 in from the mount, 45 and 43 degrees off its axis, 15 and 18 degrees up)","method":"picture `fr`, the front ring's near side: the rear pocket is 86 px along the ring where the ring's own 0.735 in (its side flat's edge) is 188 px","via":"harvest"}}],"note":"Each pocket is a round cut straight down into the cap's chamfer beside the tube, open to the side flat: two a side, a thin wall between them."},"ring_edge_bevel":{"label":"Rings, the bevel between an end face and a side flat","kind":"length","measurements":[{"id":"obliques","value":0.022,"unit":"in","pm":0.012,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount a1e22b679294 (Vortex, ..._30mm_fr_w.jpg: the mount alone from the front right and above) and 22565a4f580e (..._30mm_bl_w.jpg: from the rear left and above), 1920 x 1123 each","scaleRef":"each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture (.cache/batch9/vortex-sport-cantilever-30mm-mount/camfit.py: the outline of the daylight seen through each bore, which is the near rim on one side and the far rim on the other; the split lines on the seen end face, on the bore's far wall and on the near side flat, all in the plane of the rings' axis; 1.2 to 1.6 px on the rims, 0.1 to 1.3 px on the lines; the cameras 36.6 and 37.0 in from the mount, 45 and 43 degrees off its axis, 15 and 18 degrees up)","method":"picture `fr`: the six places where the rear ring's front face's edge meets its side flats read 0.884 to 0.917 from the middle (mean 0.9035) on that face's plane, where the side flats are 0.925 out (ring_width)","via":"harvest"}}]},"ring_split_gap":{"label":"Rings, the gap between a cap and its lower half","kind":"length","measurements":[{"id":"obliques","value":0.014,"unit":"in","pm":0.006,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount a1e22b679294 (Vortex, ..._30mm_fr_w.jpg: the mount alone from the front right and above) and 22565a4f580e (..._30mm_bl_w.jpg: from the rear left and above), 1920 x 1123 each","scaleRef":"each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture (.cache/batch9/vortex-sport-cantilever-30mm-mount/camfit.py: the outline of the daylight seen through each bore, which is the near rim on one side and the far rim on the other; the split lines on the seen end face, on the bore's far wall and on the near side flat, all in the plane of the rings' axis; 1.2 to 1.6 px on the rims, 0.1 to 1.3 px on the lines; the cameras 36.6 and 37.0 in from the mount, 45 and 43 degrees off its axis, 15 and 18 degrees up)","method":"pictures `fr` and `bl`: the dark line between each cap and its lower half is 4 to 5 px across where the cameras have 310 to 320 px/in up the rings' faces","via":"harvest"}}]},"jaw_foot_chamfer":{"label":"The fixed jaws, the chamfer along their feet","kind":"length","measurements":[{"id":"side","value":0.065,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount 910667d8ac8f (Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123)","scaleRef":"the receiver's rail slots (std.picatinny.slot_pitch), by the daylight through seven of them behind and under the mount, their centres at columns 666.52, 690.76, 714.94, 739.29, 811.72, 884.32 and 957.00 (slots -7 to -4, -1, 2 and 5 from the rear lug's): 24.207 px a slot, 61.44 px/in, no centre more than 0.15 px off the line; the rail's top is the teeth's top edge, row 417.4 under the mount (tilted 0.25 degrees with the picture)","method":"a lit band along both jaws' feet, rows 427.7 to 431.7","via":"harvest"}}]},"thread_window_d":{"label":"The window under each cap screw in a ring's lower half, across","kind":"length","measurements":[{"id":"side","value":0.065,"unit":"in","pm":0.02,"source":{"type":"photo","photo":"references/vortex-sport-cantilever-30mm-mount 910667d8ac8f (Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123)","scaleRef":"the receiver's rail slots (std.picatinny.slot_pitch), by the daylight through seven of them behind and under the mount, their centres at columns 666.52, 690.76, 714.94, 739.29, 811.72, 884.32 and 957.00 (slots -7 to -4, -1, 2 and 5 from the rear lug's): 24.207 px a slot, 61.44 px/in, no centre more than 0.15 px off the line; the rail's top is the teeth's top edge, row 417.4 under the mount (tilted 0.25 degrees with the picture)","method":"each of the rear ring's two windows is a dark dot about 4 px across","via":"harvest"}}],"note":"Where each screw's threaded hole breaks out of the lower chamfer: a small dark opening that shows the thread. The camera fitted to picture `fr` has the front ring's two on the chamfer 0.34 and 0.37 below the rings' axis, 0.70 to 0.76 out; the side view has the rear ring's 0.39 below it. Drawn as the hole itself, this wide, straight down from the screw's seat: it breaks out of the chamfer 0.27 to 0.35 below the axis."},"ring_split_depth":{"label":"The groove at each ring's split: how deep","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows it in profile.","via":"harvest"}}]},"screw_socket_depth":{"label":"A screw's six-pointed socket: how deep","kind":"length","measurements":[{"id":"assumed","value":0.02,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows it in profile.","via":"harvest"}}]},"clamp_screw_head_under_face":{"label":"A base screw's head under its clamp block's outer face","kind":"length","measurements":[{"id":"assumed","value":0.01,"unit":"in","pm":0.01,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: no view on file shows it in profile.","via":"harvest"}}]},"edge_break":{"label":"The break on the mount's machined edges","kind":"length","measurements":[{"id":"assumed","value":0.006,"unit":"in","pm":0.004,"source":{"type":"derived","basis":"An assumption for the drawing, not a reading: the pictures show every edge broken and none at a size a pixel can give; the figure is the one the other mounts on file are drawn with.","via":"harvest"}}]}}}],"parts":{"a2-flash-hider":{"id":"a2-flash-hider","name":"A2 flash hider, 1/2-28 (drawing 9349051)","manufacturer":"Mil-spec","category":"muzzle_device","description":"The M16A2's flash hider, which the Army's drawings call the compensator: five slots over the top and sides, closed underneath, on a .500-28 thread with its laminated spacer. Any maker's A2 built to drawing 9349051; the catalog part is the drawing's.","weight":"a2-flash-hider.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"thread":{"origin":[0,0,0],"note":"Device frame: on the bore axis at the barrel's shoulder, +x toward the muzzle. The spacer bears on the shoulder, the compensator on the spacer."},"front":{"origin":["{.length}",0,0],"note":"The compensator's front face: where the build's overall length ends."}},"interfaces":{"thread":{"type":"muzzle_thread","role":"device","anchor":"thread","params":{"thread":"1/2-28","thread_length":"={.thread_depth}"},"flips":false,"note":"Drawing 9349051: \".500-28 UNEF-2B MOD\", .62 minimum full thread, the threaded bore .68 +.02 deep: the longest barrel thread it takes (the spacer's thickness more, in fact)."}},"materials":{"body":{"label":"Flash hider","finish":"phosphate","recolorable":false,"color":"steel-phosphate-black","note":"Steel, AISI 4130; \"PROTECTIVE FINISH: 5.3.1.2 OF MIL-STD-171\" (drawing 9349051, notes 2 and 8). Its makers say phosphate: Windham Weaponry \"finished in Black Phosphate\", Spike's \"Finish: Mil-Spec Heavy Phosphate Finish\", Wing Tactical for Aero's \"Finish: Mil-Spec Heavy Phosphate\", KAK \"Phosphate Coated for corrosion resistance\". A nitrided one (Faxon's \"Finish: Nitride\") is another product. The two makers' own photos on file are an oiled black (BCM's 9f6749f9e2da reads #1b2024 on its body, Windham's edeff5c5fbd9 #1c2124); Wing Tactical's photo of Aero's is a dry charcoal (#4d4d4d). Drawn in the black phosphate matched on BCM's gas block, which the two makers' photos are within ten levels of (data/colors/steel.yaml)."},"spacer":{"label":"Spacer","finish":"steel","recolorable":false,"color":"placeholder-black","note":"Laminated shim stock per MIL-S-22499, composition 3 (drawing 9349052, note 2): no photo of the drawing's spacer is on file. Makers ship a crush washer in its place, dark in every photo of one (Combat Hunting: \"solid steel construction with a black finish\"; Retro Rifles lists it \"Black and Unfinished\"). A black, not matched."}},"components":{"body":{"label":"Compensator","material":"body"},"spacer":{"label":"Spacer","material":"spacer"}},"geometry":{"model":"a2-flash-hider.glb","components":{},"approximations":["Built from the Army's two drawings alone (9349051 and 9349052): the rear section with its two wrench flats and two full-radius grooves, the slotted cage a little smaller in diameter between two chamfered steps, the front ring, the bore through the front with the cone behind it, and the five slots, each cut the way the drawing dimensions it (a .49 R cut centred .610 off the axis and .590 behind the front face, .175 wide, its deepest edge narrowing at 28° to .08).","Slots up and to both sides, closed underneath, as it is timed.","Which section is the smaller diameter is a reading of the drawing, checked on a photo of a real one (Windham's): its cage, grooves and steps measure where these callouts put them. The ledger's cage_od says how.","The spacer is drawn at the middle of what it can be installed at (0.030 to 0.075 in): laminations are peeled until the closed side faces down. The thread isn't cut, and behind the cone the hole simply ends.","The 22RB's muzzle stands 0.51 in ahead of its shoulder (its threaded end, measured bare on the user's own barrel), and this takes 0.69: it fits.","Edges broken at 0.01 in (note 4: .005 +.010)."],"ledger":["a2-flash-hider.compensator_length","a2-flash-hider.od","a2-flash-hider.cage_od","a2-flash-hider.rear_length","a2-flash-hider.cage_length","a2-flash-hider.groove_width","a2-flash-hider.groove_d","a2-flash-hider.flats_across","a2-flash-hider.slot_cutter_r","a2-flash-hider.slot_cutter_offset","a2-flash-hider.slot_center_from_front","a2-flash-hider.slot_width","a2-flash-hider.chamber_d","a2-flash-hider.spacer_thickness","a2-flash-hider.length"]},"profiles":{},"gaps":[]},"aero-556-16-mid-barrel":{"id":"aero-556-16-mid-barrel","name":"16\" 5.56 CMV barrel, mid-length","manufacturer":"Aero Precision","sku":"APBA100060C","url":"https://www.aeroprecisionusa.com/556-16-mid-cmv-barrel","category":"barrel","description":"Aero Precision's 16 in 5.56 NATO barrel: 4150 chrome moly vanadium, QPQ, 1:7 twist, a mid-length gas system on a .750 in journal, an M4 extension, a 1/2-28 muzzle thread.","weight":"aero-556-16-mid-barrel.weight","barrelLength":"aero-556-16-mid-barrel.length","cartridge":{"takes":["5.56 NATO"],"stated":"Caliber 5.56 NATO","source":"https://www.aeroprecisionusa.com/556-16-mid-cmv-barrel (Aero's spec table, as cached: harvest.quote)"},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"extension":{"origin":[0,0,0],"note":"The barrel extension's flange on the bore axis, +x toward the muzzle."},"muzzle":{"origin":["{.shoulder_x}",0,0]},"gas_journal":{"origin":["{.gas_port_x}",0,0]}},"interfaces":{"barrel_extension":{"type":"ar15.barrel_extension","role":"barrel","anchor":"extension","params":{},"flips":false},"muzzle":{"type":"muzzle_thread","role":"barrel","anchor":"muzzle","params":{"thread":"1/2-28","thread_length":"={.thread_length}"},"flips":false,"note":"Aero: \"Thread Pitch 1/2-28 Threaded\". The thread's length isn't published: it is read off Aero's side photo (0.63 ± 0.03 in, the Army barrel's .63)."},"gas_journal":{"type":"ar15.gas_journal","role":"barrel","anchor":"gas_journal","params":{"journal_od":"={.journal_od}"},"flips":false},"gas_system":{"type":"ar15.gas_system","role":"barrel","params":{"length":"mid"},"flips":false,"note":"Aero Precision names it \"16\" 5.56 CMV Barrel, Mid-Length\". What the platform checks a gas tube against a barrel by (D83)."}},"materials":{"barrel":{"label":"Barrel","finish":"nitride","recolorable":false,"color":"steel-nitride-black","note":"Aero: \"Barrel Finish QPQ Corrosion Resistant\" and \"4150 Chrome Moly Vanadium with a QPQ corrosion resistant finish\": salt-bath nitride, the one finish this number is sold in. A black, not fitted to a photo: on Aero's two photos (63b167b2dab1, 628368f22a19) the tube reads #474747 with a band of light along it, as a satin black does under a softbox. One slot: the extension is the barrel's black; its index pin, bright bare steel in Aero's closer photo, isn't drawn (geometry.approximations). Not drawn: the lasered \"5.56x45 NATO 1/7 4150 CrMoV\"."}},"components":{},"geometry":{"model":"aero-556-16-mid-barrel.glb","components":{},"approximations":["Turned from its traced side outline, extension to muzzle shoulder: its diameters at the scale its gas block journal's .750 gives, its length at the published one (the two agree within half a percent, read at the photo's edge). The app turned the same outline itself until 2026-10-06, and still does where the model isn't to hand.","The muzzle thread is a helix, 28 to the inch, between the roots and crests of the Army barrel's 1/2-28 (Aero states 1/2-28): a plain V without the flats of its form, right-hand (assumed: its designation marks no other), running out at the shoulder over its last pitch, with no relief there or chamfer at the muzzle. The photo's silhouette of the thread is a smooth neck between the two diameters: a pitch is two of its pixels.","The bore is one plain hole right through, at the Army drawing's diameter for the cartridge (not a measurement of this barrel): no lands and grooves, no chamber, no crown. Not drawn: the gas port, the extension's lugs and its indexing pin, the dimple under the journal."],"ledger":["aero-556-16-mid-barrel.overall_length","aero-556-16-mid-barrel.extension_rear_x","aero-556-16-mid-barrel.flange_od","aero-556-16-mid-barrel.shoulder_x","aero-556-16-mid-barrel.gas_port_x","aero-556-16-mid-barrel.muzzle_od","aero-556-16-mid-barrel.bore_d","aero-556-16-mid-barrel.thread_major_d","aero-556-16-mid-barrel.thread_minor_d","aero-556-16-mid-barrel.thread_pitch","aero-556-16-mid-barrel.thread_length"]},"profiles":{"side":{"plane":"xy","origin":"the silhouette's rear tip, on the axis; the outline begins at the extension's rear face","offset":{"x":"extension_rear_x"},"points":[[0.058,0.473],[0.058,-0.473],[0.081,-0.496],[1.002,-0.496],[1.056,-0.587],[1.164,-0.587],[1.218,-0.478],[1.904,-0.478],[2.012,-0.442],[2.211,-0.424],[2.301,-0.388],[2.409,-0.388],[2.427,-0.37],[2.608,-0.352],[2.626,-0.334],[9.014,-0.298],[9.231,-0.37],[9.303,-0.424],[9.916,-0.424],[9.952,-0.37],[9.97,-0.388],[10.241,-0.388],[10.259,-0.37],[15.06,-0.37],[15.078,-0.388],[15.186,-0.388],[15.222,-0.352],[15.944,-0.352],[15.971,-0.289],[15.953,-0.271],[15.98,-0.226],[16.106,-0.262],[16.124,-0.244],[16.142,-0.262],[16.16,-0.244],[16.485,-0.244],[16.503,-0.262],[16.539,-0.244],[16.581,-0.202],[16.581,0.184],[16.521,0.244],[16.503,0.226],[16.034,0.226],[15.98,0.208],[15.971,0.289],[15.944,0.334],[15.222,0.334],[15.204,0.352],[11.847,0.352],[11.829,0.37],[9.952,0.37],[9.934,0.352],[9.898,0.424],[9.862,0.406],[9.285,0.406],[9.158,0.334],[9.032,0.298],[2.662,0.334],[2.644,0.352],[2.463,0.37],[2.445,0.388],[2.319,0.388],[2.211,0.424],[1.994,0.442],[1.796,0.496],[1.687,0.478],[1.669,0.496],[1.218,0.496],[1.209,0.541],[1.164,0.587],[1.056,0.587],[1.029,0.559],[1.02,0.496],[0.532,0.496],[0.081,0.496]],"scaleRefs":["aero-556-16-mid-barrel.flange_od"],"inputs":{"aero-556-16-mid-barrel.flange_od":1.173,"aero-556-16-mid-barrel.outline_front_face":16.581,"aero-556-16-mid-barrel.outline_rear_face":0.058},"tolerance":0.013,"photo":"references/aero-556-16-mid-barrel 63b167b2dab1 (Aero's gallery: the 16 in 5.56 CMV mid-length barrel from the side, 1000 x 630)","method":"luminance < 235, 1 boxes excluded, largest piece, holes filled; scale from aero-556-16-mid-barrel.flange_od = 1.173 in (y-extent 65 px → 55.4 px/in); origin at x min, y center of the outline; clipped to x min {.outline_rear_face} = 0.058, x max {.outline_front_face} = 16.581; Douglas-Peucker at 0.013 in with the extremes kept: 75 points (IoU 0.994 with the full outline); The extension reads 0.99 across (the Army's limit for it is .9990): at 160 it was 0.69 to 0.73, with necks where the bright band along it met the flange.; checks: height (tooth tops, max over 0.05 in windows) along x [10.1, 11.7] 0.740 ± 0.066 in vs aero-556-16-mid-barrel.journal_od 0.75 ± 0.001 (confirmed): agrees; height (tooth tops, max over 0.05 in windows) along x [0.2, 0.9] 0.993 ± 0.074; centre between the top (max over 0.4 in windows) along x [2.8, 9.2] 0.000 ± 0.054 (tools/trace.py)","via":"harvest","note":"Black on white, the extension bare steel: the outline is the silhouette at 235 of 255, cut at its two end faces. Its diameters are at the journal's scale, its length at the published one: with the edge at 235 the two scales are 0.1% apart."}},"gaps":[{"what":"A model: the app turns its traced outline, so its bore, its gas port, its index pin and its thread's rings aren't drawn, and its steps are as square as a 1000 px photo's pixels (0.018 in)","need":"The two other barrels' script run on this outline (the port and the pin are both in the photo on file, facing the lens), or a larger side photo"},{"what":"Where the 16 in is measured from","need":"Aero's statement (taken from the barrel's breech end, as the catalog's two other 16 in barrels are; from the bolt's face it would be an eighth shorter overall)"},{"what":"The muzzle shoulder closer than 0.06 in: its own photo has 14.89 (a pixel of it is 0.018 in, and its scale is the published 16 in), Aero's photo of the complete upper 14.95 ± 0.08","need":"A larger straight side photo, or Aero's drawing"}]},"aero-556-bcg":{"id":"aero-556-bcg","name":"5.56 bolt carrier group, complete, black nitride","manufacturer":"Aero Precision","sku":"APRH100615C","url":"https://www.aeroprecisionusa.com/ar15-556-bolt-carrier-group-complete-black-nitride","category":"bolt_carrier_group","description":"Aero Precision's complete 5.56 bolt carrier group: an M16-cut 8620 carrier and a 9310 bolt, black nitride.","weight":"aero-556-bcg.weight","cartridge":{"takes":["5.56 NATO"],"stated":"5.56 Bolt Carrier Group, Complete - Black Nitride","source":"https://www.aeroprecisionusa.com/ar15-556-bolt-carrier-group-complete-black-nitride (the product's name on Aero's page, which has no caliber row; as cached: harvest.quote)"},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"channel":{"origin":[0,0,0]}},"interfaces":{"carrier_channel":{"type":"ar15.carrier_channel","role":"carrier","anchor":"channel","params":{},"flips":false}},"materials":{"body":{"label":"Carrier group","finish":"nitride","recolorable":false,"color":"steel-nitride-black","sheen":"satin","note":"Aero: \"Finish Black Nitride\" and \"Black Nitride Finish - advanced lower friction coating that minimizes the need for lubricants and cleaning\" (its page for APRH100615C; the \"No Logo\" and \"PRO\" groups beside it are other products). The carrier, the key, the cam pin and the bolt are one slot: all one polished black in Aero's three photos (a4082e72b225, 2c58757fc40b, 8e96e1c5131e). A black, not fitted to a photo: Aero's photos have a softbox lying along it, and its tail reads #808080 there. Satin: the highlights are narrow and bright. Not drawn: Aero's \"A\" lasered white on the right side, the extractor with its \"Black o-ring insert\"."},"screws":{"label":"Key screws","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The key's two socket screws (Aero: \"Properly staked gas key\"): no photo of Aero's shows them from above and no page names their finish. A black, not matched."}},"components":{},"geometry":{"model":"aero-556-bcg.glb","components":{},"approximations":["Its shape is the Army's drawings', not Aero's own: Aero's page has \"M16-cut carrier\" and \"Carrier has forward assist serrations\" and gives no size, so it is drawn as the M16 carrier (8448507), its key (8448506) and screws (8448508), the cam pin (8448502) and the bolt (8448510) at those drawings' nominal sizes, as BCM's and Toolcraft's are (2026-10-05; a plain cylinder until then). Nothing was measured from Aero's photos.","Drawn as the Army's assembly drawing (8448501) has it, out of the rifle: the bolt forward in the carrier (unlocked) and the cam pin upright. In battery the bolt is turned 22 1/2° and stands .255 to .325 in further back in the carrier; the carrier's rear face is put at the receiver's rear face.","Not drawn: the bores inside the carrier ahead of the slot and the bolt behind the carrier's front face, the extractor (its claw stands in as an eighth lug) and the ejector, the firing pin and its retaining pin, the gas rings, the key's 22°30' relief and its staking, any marking, fillets and edge breaks beyond the two cut corners and a small bevel. What the drawing left unresolved is assumed as the other two carriers' parts list it."],"ledger":["aero-556-bcg.length","aero-556-bcg.od"]},"profiles":{},"gaps":[{"what":"Aero's own two side photos against the model","need":"A comparison by silhouette, as BCM's photos were: nothing of Aero's was measured for it"}]},"aero-750-gas-block":{"id":"aero-750-gas-block","name":".750 low profile gas block","manufacturer":"Aero Precision","sku":"APRH101205C","url":"https://www.aeroprecisionusa.com/750-low-profile-gas-block-w-aero-logo-nitride","category":"gas_block","description":"Aero Precision's low-profile gas block for a .750 in journal: 4140 steel, nitride, held by two 10-32 set screws. The gas tube's roll pin isn't included.","weight":"aero-750-gas-block.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"journal":{"origin":[0,0,0],"note":"On the bore axis at the gas port, +x toward the muzzle. The port is where the standard tube's gas hole lands with its pin in the block's cross hole: 0.269 in ahead of the rear face (port_from_rear), which leaves the rear face three hundredths ahead of the journal's shoulder."},"gas_tube":{"origin":[0,"{.tube_hole_above_bore}",0],"x":[-1,0,0],"note":"The tube's hole, +x rearward toward the receiver: 0.156 below where the tube enters the receiver (the tube's bend takes it up), as the block's photo and the drawings both put it (2026-10-03; it had been at the receiver's height, 0.78, which stood the tube above the block's top)."}},"interfaces":{"gas_journal":{"type":"ar15.gas_journal","role":"block","anchor":"journal","params":{"journal_od":"={.journal_id}"},"flips":false,"note":"Aero: \"Fits barrels with .750 Outer Diameter\"."},"gas_tube":{"type":"ar15.gas_tube","role":"block","anchor":"gas_tube","params":{},"flips":false}},"materials":{"body":{"label":"Gas block","finish":"nitride","recolorable":false,"color":"steel-nitride-black","note":"Aero: \"Finish Nitride\" and \"Nitride coating\" on \"4140 hardened steel\" (its page for APRH101205C, the one with the logo; the \"No Logo\" block is another number). A black, not fitted to a photo: Aero's side view (a20acc7a2f17) reads #312e2e between bands of light. The bore's wall is black with the rest (the three-quarter view, ffbee1a0d42b). The set screw that is drawn (\"Steel 10-32 x 3/16 Knurled Cup Point\") is a piece of this slot: no photo shows a screw but as a dark edge under the tab. Aero's \"A\" in a ring, lasered pale on the front face, isn't drawn."}},"components":{},"geometry":{"model":"aero-750-gas-block.glb","components":{},"approximations":["Its section is Aero's own end view, straight along the bore and scaled by the bore as the .750 journal, framed by the two heights read on that view (the boss's top 0.79 in above the bore, the tab's flat 0.568 below it: the traced outline is taken 0.7% smaller and 0.004 in higher than it was traced, its frame having been the bore as a circle through the set screw's tip in its floor). Its two sides differ by up to 0.01 in and the model's section is their mean about the bore's centre.","The section is run unchanged along the length the two side views give in the boss's rows (1.013 in), with every edge broken by 0.012 in (two to five pixels in the side views; the front face's rim reads the larger and one size is drawn). The bore is cut through at the journal's .750.","The gas tube's hole (its height above the bore, its diameter, how far it runs past the pin) and the roll pin's hole's diameter are the Army's front sight's (drawing 8448566): the block takes the same tube and pin, and the pin's hole in both side views is at that height and size within a pixel, and 0.687 in ahead of the rear face where the Army's sight has it at .688. The tube's hole enters from the rear face, which no photo on file shows, and the logo face is closed, as two photos show.","The gas port is where the standard tube's gas hole lands (.418 behind the pin, drawing 8448567): 0.269 in ahead of the rear face. The port's hole up from the bore isn't drawn (inside).","One of its two set screws is drawn, the one both side views show standing out of the tab's flat 0.258 in behind the front face: as it is on a barrel, its tip on the journal and its end 0.005 in inside the flat (in the photos, off a barrel, it stands 0.011 in proud). Its length is Aero's (3/16), its end as wide as it shows (0.15), its diameter the same thread's screw as photographed in another maker's block (0.185), its hex socket the 3/32 key Aero's support names, drawn one key deep. Its knurled cup point and its thread aren't drawn.","Not drawn: the second set screw (nothing on file says where along the tab it is), Aero's \"A\" in a ring lasered on the front face (lines a few thousandths of an inch wide)."],"ledger":["aero-750-gas-block.journal_id","aero-750-gas-block.length","aero-750-gas-block.height_above_bore","aero-750-gas-block.tab_below_bore","aero-750-gas-block.od","aero-750-gas-block.boss_width","aero-750-gas-block.port_from_rear","aero-750-gas-block.pin_hole_from_front","aero-750-gas-block.pin_hole_d","aero-750-gas-block.pin_to_port","aero-750-gas-block.tube_hole_above_bore","aero-750-gas-block.tube_hole_d","aero-750-gas-block.tube_hole_past_pin","aero-750-gas-block.edge_break","aero-750-gas-block.set_screw_from_front","aero-750-gas-block.set_screw_d","aero-750-gas-block.set_screw_end_d","aero-750-gas-block.set_screw_length","aero-750-gas-block.set_screw_key"]},"profiles":{"front":{"plane":"zy","origin":"the bore's axis","offset":{},"points":[[-0.443,-0.049],[-0.427,-0.132],[-0.384,-0.233],[-0.326,-0.312],[-0.258,-0.375],[-0.215,-0.428],[-0.177,-0.496],[-0.154,-0.557],[-0.13,-0.576],[0.065,-0.576],[0.12,-0.574],[0.144,-0.562],[0.192,-0.453],[0.233,-0.403],[0.334,-0.309],[0.395,-0.228],[0.443,-0.107],[0.453,-0.051],[0.453,0.037],[0.448,0.04],[0.45,0.004],[0.445,0.004],[0.445,0.052],[0.427,0.131],[0.397,0.199],[0.402,0.204],[0.392,0.207],[0.367,0.247],[0.379,0.245],[0.245,0.406],[0.23,0.414],[0.207,0.46],[0.182,0.551],[0.175,0.657],[0.149,0.712],[0.159,0.707],[0.154,0.72],[0.142,0.725],[0.147,0.73],[0.123,0.754],[0.087,0.777],[0.006,0.792],[-0.067,0.769],[-0.111,0.733],[-0.134,0.7],[-0.149,0.657],[-0.167,0.523],[-0.205,0.434],[-0.26,0.358],[-0.359,0.255],[-0.407,0.169],[-0.44,0.052]],"scaleRefs":["aero-750-gas-block.journal_id"],"inputs":{"aero-750-gas-block.journal_id":0.75},"tolerance":0.005,"photo":"references/aero-750-gas-block 3f97b27af899 (Aero's gallery: the .750 low-profile gas block end-on, the boss up, 1000 x 631)","method":"luminance < 200, largest piece; scale from the hole at (509.5, 359.7): 296.6 px across (circle through the 50% edge; 295.8–297.4 px at 65–35%) = aero-750-gas-block.journal_id 0.75 in → 395.4 px/in (the bore, seen through: the .750 journal it is bored for); origin at the hole's centre; Douglas-Peucker at 0.005 in with the extremes kept: 52 points (IoU 0.992 with the full outline); checks: y_max 0.792 ± 0.005 in vs aero-750-gas-block.height_above_bore 0.79 ± 0.015 (provisional): agrees; width 0.895 ± 0.008 in vs aero-750-gas-block.od 0.884 ± 0.01 (provisional): agrees (tools/trace.py)","via":"harvest","note":"Its outline end-on: the ring about the barrel, the tube's boss on top, the set screws' tab underneath. The bore is open: a section with a hole is drawn solid and the barrel fills it."}},"gaps":[{"what":"The second set screw's place along the tab, and both screws' sockets","need":"A photo of the underside: the two side views show one screw's end 0.258 in behind the front face and nothing of the other, and the end view shows a screw's tip in the bore's floor without saying which"},{"what":"The rear face: the gas tube's hole as Aero drills it","need":"A photo of the rear face, or of the bore from behind: the hole's size and depth are the Army's front sight's"},{"what":"Its length to better than a hundredth","need":"Aero publishes none: 1.013 in is the two side views in the boss's rows, each a few degrees off square (the ring's rows read 1.03 to 1.04). A seller's figure, or a view from above"},{"what":"Its weight against its metal","need":"The model's volume in steel comes to about 1.5 oz against Aero's 1.6: inside the section's ± (a hundredth of an inch on the ring's wall is a tenth of an ounce), and not a second reading of anything"}]},"aero-ar15-front-sight-post-kit":{"id":"aero-ar15-front-sight-post-kit","name":"AR15 Front Sight Post Kit","manufacturer":"Aero Precision","sku":"APRH100526C","url":"https://www.kygunco.com/product/aero-precision-aprh100526c-front-sight-post-kit-detent-spring-sight","category":"front_sight_post","description":"Aero Precision's mil-spec front sight post kit: the A2 post, its detent and the detent's spring (KYGUNCO's page: \"AR15 A2 Front Sight AR15 Front Sight Detent AR15 Front Sight Detent Spring\"), \"intended for use in AR15's that have a front sight base (FSB)\". The post screws into the base's tower and the spring-loaded detent holds it at each quarter turn; it is drawn screwed down onto the counterbore's floor, and the detent and its spring, under its flange in the base, aren't drawn. Aero's own page for the number wasn't found; BCM's shop lists no post of its own.","weight":"aero-ar15-front-sight-post-kit.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"seat":{"origin":[0,0,0],"note":"Part frame: on the post's axis at the top of the base's tower (the floor between the wings), +x toward the muzzle, +y up. The post's own seat, its flange's underside, is seat_below_tower_top under it: the Army's base's counterbore floor (8448566)."}},"interfaces":{"front_sight_post":{"type":"ar15.front_sight_post","role":"post","anchor":"seat","params":{},"flips":false,"note":"KYGUNCO, of Aero's kit: \"Our mil-spec AR15 front sight post kit is intended for use in AR15's that have a front sight base (FSB).\" Its thread is the Army's post's .164-36 UNF-2A (9349056), the base's tower hole's 8-36 (8448566)."}},"materials":{"post":{"label":"Post","finish":"phosphate","recolorable":false,"color":"steel-phosphate-black","note":"No page names the kit's finish (Blackstone's title: \"Black Finish\"). The Army's post is phosphated (9349056 note 7: \"PROTECTIVE FINISH:-5.3.1.2 OF MIL-STD-171\"), and AR15Discounts' photo (fef49a0dd319) shows a black post with a dull face. A black phosphate (steel-phosphate-black), a black on phosphate being its finish type's look, not fitted to a photo."}},"components":{},"geometry":{"model":"aero-ar15-front-sight-post-kit.glb","components":{},"approximations":["The Army's A2 post (9349056) at the middle of each of its tolerances: a square blade .070 across and .268 tall on a flange .3645 across and .060 thick, its four detent notches (r .0468 on a .400 circle), a .062 neck and a .164-36 thread .46 long with its end chamfered. AR15Discounts' one photo of Aero's kit shows that post; no seller states a size.","Drawn screwed down, its flange on the base's counterbore floor (.227 under the tower's top, 8448566): the blade's top then stands .101 over the tower's top, under the wings' tips. On a rifle it is turned up to zero the sight, a 36th of an inch a turn.","The thread is a helix between the drawing's major diameter and a root as far inside its pitch diameter as the crest is outside it (a symmetric 60 degree V); the neck under the flange is drawn at that root. The notches are set square to the blade's faces (the drawing doesn't say how they stand to the blade).","Not drawn: the curved roots where the blade meets the flange (.13 R, four places), the detent and its spring (in the base, under the flange)."],"ledger":["aero-ar15-front-sight-post-kit.height","aero-ar15-front-sight-post-kit.seat_below_tower_top","aero-ar15-front-sight-post-kit.blade_width","aero-ar15-front-sight-post-kit.blade_height","aero-ar15-front-sight-post-kit.flange_d","aero-ar15-front-sight-post-kit.flange_thickness","aero-ar15-front-sight-post-kit.notch_r","aero-ar15-front-sight-post-kit.notch_circle_d","aero-ar15-front-sight-post-kit.shank_length","aero-ar15-front-sight-post-kit.thread_major_d","aero-ar15-front-sight-post-kit.thread_pitch"]},"profiles":{},"gaps":[{"what":"Aero's own page and photos of the kit","need":"Aero's product page for APRH100526C (not found), or a seller's photos of the post from the side and from above"},{"what":"The kit's weight","need":"A seller's figure for the kit itself: KYGUNCO's 1 lb is a parcel's; the figure is its steel"}]},"aero-carbine-gas-tube":{"id":"aero-carbine-gas-tube","name":"Gas Tube, Carbine Length","manufacturer":"Aero Precision","sku":"APRH100017C","url":"https://www.aeroprecisionusa.com/gas-tube-carbine-length-stainless-steel","category":"gas_tube","description":"Aero Precision's gas tube for a carbine-length gas system, 9.75 in, with its roll pin: stainless steel, or the same tube in black Melonite. Aero: \"Stainless Steel Gas Tube for AR15 & AR10 rifles\".","weight":"aero-carbine-gas-tube.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"block":{"origin":[0,0,0],"note":"The tube's gas hole, where it stands over the block's port, on the front run's axis. +x rearward (the block's own anchor is turned that way)."}},"interfaces":{"gas_tube":{"type":"ar15.gas_tube","role":"tube","anchor":"block","params":{},"flips":false},"gas_system":{"type":"ar15.gas_system","role":"tube","params":{"length":"carbine"},"flips":false,"note":"Aero Precision names it \"Gas Tube, Carbine Length - Stainless Steel\", and lists its lengths as \"Pistol length 6.6875\", Carbine length 9.8\", Mid-Length 11.75”, Rifle length 15.125\"\" (https://www.aeroprecisionusa.com/gas-tube-stainless-steel). What the platform checks a gas tube against a barrel by (D83)."}},"materials":{"tube":{"label":"Gas tube","finish":"stainless","recolorable":false,"color":"stainless-natural","options":{"stainless":{"label":"Stainless Steel","finish":"stainless","color":"stainless-natural","sku":"APRH100017C","source":"https://www.aeroprecisionusa.com/gas-tube-carbine-length-stainless-steel"},"melonite":{"label":"Melonite","finish":"nitride","color":"steel-nitride-black","sku":"APRH100281C","source":"https://www.aeroprecisionusa.com/gas-tube-carbine-length-melonite"}},"default":"stainless","note":"Two finishes of one tube, each under its own number. Aero: \"Stainless Steel Gas Tube for AR15 & AR10 rifles\" (\"Gas Tube, Carbine Length - Stainless Steel\"), bright all over in Aero's and MidwayUSA's photos (d4a9aa9610b2, 4e863297f463; MidwayUSA: \"Color: Stainless\"), the plugged front end with it; and \"Melonite Gas Tube for AR15 & AR10 rifles\" (\"Gas Tube, Carbine Length - Melonite\"), black all over, the plugged end and the head with it (0b1df4671af0, 25748a62f53b; MidwayUSA: \"Color: Black Melonite\"). Melonite is a salt-bath nitride: a polished black, whose finish carries its look. Neither is fitted to a photo: bright metal isn't, and what a photo reads on a polished black is the studio's lights (Aero's melonite tube reads #1e1e1f and #282828 either side of a band of light along it, #e0e0e2; its stainless one #6a6664 to #c7c2bf about a band of white). One piece in both: the \"Roll pin included\" isn't drawn."}},"components":{},"geometry":{"model":"aero-carbine-gas-tube.glb","components":{},"approximations":["Swept along its centre line at the Army drawing's diameter (8448567: .180, at the head and at the plugged front end) and Aero's published length: a level front run, a round, a straight slope, an equal round and a level rear run the drawing's .156 higher. Where the bend lies and how round it is are read on the tube's own side photos (it begins 3.71 in and ends 5.53 in from the rear end, its rounds about 3.6 in in radius, the slope between them 6.2 degrees); the drawing, which is of the rifle's tube, has rounds of 1.50, and the two shapes are within 0.004 in of each other.","The front end as the drawing and the photos have it: closed by a plug, a groove pressed round it each side of the roll pin's cross hole (.078, .187 from the end, across the rifle), the gas hole (.125, .605 from the end) through the lower wall only. The grooves' places, width and depth are read on the photos, where each is two to four pixels: each is drawn as a smooth dip, and its real section isn't known. The plug is one piece with the tube, its length scaled off the drawing.","The rear end as the photos have it: a head a tenth of an inch long at the tube's diameter, and between it and a line 2.27 in from the rear end a stretch 0.013 in thinner (about a pixel in each of four photos). The stretch's two ends are drawn as square steps; which of the two stretches is the drawing's .180 isn't read, and the head and the tube ahead of the line are drawn at it.","Both end faces' rims are broken by 0.015 in, as large as the photos' blur.","The bore is what Aero's 0.5 oz leaves of a stainless tube of this length and diameter (0.134 in); the Army's section, drawn without a figure, has a smaller one (0.09). It shows only at the open rear end, inside the receiver.","Its diameter isn't measured on this tube: every photo on file reads it 6 to 16% thin against a white ground, and no page states it. One seller says of Aero's stainless tubes \"Made to Mil-Spec dimensions\" (Wing Tactical).","The roll pin that comes with it isn't drawn: it goes across the gas block through the tube's cross hole, and its length has no source (one seller's oblique photo of a black pin beside a longer tube reads 0.28 to 0.44 in). The plug's seam on the front end face isn't drawn either; it is inside the block's blind hole."],"ledger":["aero-carbine-gas-tube.length","aero-carbine-gas-tube.od","aero-carbine-gas-tube.bend_offset","aero-carbine-gas-tube.bend_radius","aero-carbine-gas-tube.bend_start_from_rear","aero-carbine-gas-tube.bend_end_from_rear","aero-carbine-gas-tube.gas_hole_from_front","aero-carbine-gas-tube.gas_hole_d","aero-carbine-gas-tube.pin_hole_from_front","aero-carbine-gas-tube.pin_hole_d","aero-carbine-gas-tube.crimp_front_from_front","aero-carbine-gas-tube.crimp_rear_from_front","aero-carbine-gas-tube.crimp_width","aero-carbine-gas-tube.crimp_depth","aero-carbine-gas-tube.head_length","aero-carbine-gas-tube.relief_end_from_rear","aero-carbine-gas-tube.relief_depth","aero-carbine-gas-tube.end_break","aero-carbine-gas-tube.plug_length","aero-carbine-gas-tube.bore"]},"profiles":{"side":{"plane":"xy","origin":"the front end face, at the height of the front run's underside: the part's frame is the gas hole's distance behind that face (gas_hole_from_front), on the front run's axis","offset":{},"points":[[0,0.129],[0.023,0.107],[0,0.084],[0,0.062],[0.011,0.05],[0.012,0.017],[0.028,0],[0.073,0],[0.085,0.011],[0.118,0.012],[0.13,0],[0.141,0.012],[0.163,0],[0.174,0.012],[0.242,0.012],[0.264,0.001],[0.287,0.012],[0.332,0.012],[0.343,0.001],[0.377,0.001],[0.399,0.001],[0.41,0.012],[0.489,0.013],[0.568,0.002],[0.579,0.013],[0.658,0.013],[0.702,0.013],[0.714,0.002],[0.792,0.002],[0.804,0.014],[0.882,0.014],[0.905,0.003],[1.242,0.004],[1.253,0.015],[1.298,0.015],[1.331,0.015],[1.343,0.004],[1.421,0.004],[1.444,0.016],[1.466,0.005],[1.511,0.005],[1.522,0.016],[1.545,0.016],[1.556,0.005],[3.915,0.012],[3.926,0.001],[3.949,0.012],[4.466,0.014],[4.477,0.025],[4.6,0.026],[4.611,0.037],[4.701,0.037],[4.713,0.048],[4.802,0.049],[4.814,0.06],[4.926,0.06],[4.937,0.072],[5.016,0.072],[5.027,0.083],[5.128,0.083],[5.139,0.095],[5.195,0.095],[5.207,0.106],[5.319,0.106],[5.33,0.118],[5.521,0.13],[5.532,0.141],[5.611,0.141],[5.622,0.152],[5.734,0.153],[5.746,0.164],[6.004,0.165],[6.015,0.176],[6.914,0.179],[6.925,0.168],[7.262,0.169],[7.442,0.169],[7.453,0.181],[7.487,0.181],[9.115,0.186],[9.127,0.175],[9.194,0.175],[9.205,0.186],[9.239,0.186],[9.25,0.175],[9.688,0.176],[9.7,0.165],[9.722,0.165],[9.739,0.182],[9.739,0.227],[9.75,0.238],[9.739,0.261],[9.75,0.283],[9.75,0.317],[9.71,0.345],[9.699,0.334],[9.677,0.334],[7.441,0.327],[7.43,0.338],[5.869,0.333],[5.857,0.322],[5.689,0.321],[5.678,0.31],[5.599,0.31],[5.588,0.298],[5.476,0.298],[5.464,0.287],[5.408,0.286],[5.397,0.275],[5.296,0.275],[5.285,0.264],[5.172,0.263],[5.161,0.252],[5.116,0.252],[5.105,0.241],[4.97,0.24],[4.959,0.229],[4.892,0.229],[4.881,0.217],[4.667,0.206],[4.656,0.194],[4.589,0.194],[4.577,0.183],[4.487,0.183],[4.476,0.171],[1.118,0.161],[1.106,0.172],[1.016,0.172],[0.331,0.169],[0.32,0.158],[0.298,0.158],[0.253,0.18],[0.241,0.169],[0.028,0.168]],"scaleRefs":["aero-carbine-gas-tube.length"],"inputs":{"aero-carbine-gas-tube.length":9.75},"tolerance":0.006,"photo":"references/aero-carbine-gas-tube 4e863297f463 (MidwayUSA's picture of the stainless carbine tube (924189.jpg), whole and level on white, 880 x 660)","method":"luminance < 235, closing ×2, largest piece, holes filled; rotated +180.2° as declared; scale from aero-carbine-gas-tube.length = 9.75 in (x-extent 868 px → 89.0 px/in); origin at x min, y min of the outline; Douglas-Peucker at 0.006 in with the extremes kept: 134 points (IoU 0.990 with the full outline); the picture has the tube turned half round from how it sits in a rifle (its front end at the left and the higher): mirrored and turned 180 degrees, the front end is at x 0 and the rear run above the front. One scale reference, the tube's own published length between its end faces: nothing else of known size is in the picture; checks: width 9.750 ± 0.034 in vs aero-carbine-gas-tube.length 9.75 ± 0.005 (confirmed): agrees; height (tooth tops, max over 0.05 in windows) along x [0.9, 3.4] 0.158 ± 0.034 in vs aero-carbine-gas-tube.od 0.18 ± 0.002 (confirmed): agrees; (centre between the top (max over 0.05 in windows) along x [6.3, 7.3]) − (centre between the top (max over 0.05 in windows) along x [2.2, 4.0]) 0.168 ± 0.048 in vs aero-carbine-gas-tube.bend_offset 0.156 ± 0.01 (confirmed): agrees (tools/trace.py)","via":"harvest","note":"The tube from its right side as it sits in a rifle, +x rearward: the plugged front end at x 0, the rear run the bend's drop above the front run. The outline is the silhouette at the 235 level, which reads the tube 12 to 15% thin (bright metal on white): its centre line is the reading, not its thickness. The grooves round the plugged end, the gas hole's notch and the head are at the limit of the picture (a pixel is 0.011 in)."}},"gaps":[{"what":"Its outside diameter and its bore, as Aero makes them","need":"A figure from Aero or a seller, or a view of its end with something of known size in it: the diameter drawn is the Army's drawing's, the bore what Aero's weight leaves"},{"what":"The grade of its stainless steel","need":"Aero's own word for it (its pages say \"Stainless Steel\" and no more)"},{"what":"The roll pin it comes with","need":"Its length, from Aero or a seller: the pin goes in the .078 cross hole and isn't drawn"},{"what":"A carbine tube's own drawing","need":"The Army's drawing of the M4's gas tube (the package on file has the rifle's, 8448567): where its bend lies, and its rounds"},{"what":"The sections of the two grooves round the plug and of the relief behind the head","need":"A close photo of each end with a scale on the tube: the product photos have them at one to four pixels"}]},"aero-charging-handle":{"id":"aero-charging-handle","name":"AR15/M4 5.56 charging handle","manufacturer":"Aero Precision","sku":"APRH100000C","url":"https://www.aeroprecisionusa.com/ar15-charging-handle","category":"charging_handle","description":"Aero Precision's standard mil-spec charging handle: 7075 aluminium, black anodized.","weight":"aero-charging-handle.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"channel":{"origin":[0,0,0],"note":"The T's shoulder on the channel's axis, +x toward the muzzle: where the block behind it steps down to the shaft's width. It stops against the front wall of the open notch under a receiver's rail's rear end (the receiver's handle_seat_x), and the hook's tip is `length` ahead."}},"interfaces":{"charging_handle_channel":{"type":"ar15.charging_handle_channel","role":"handle","anchor":"channel","params":{},"flips":false}},"materials":{"body":{"label":"Charging handle","finish":"anodized","recolorable":false,"color":"placeholder-black","note":"Sold in the one finish: \"Black Anodize\" (Aero's page, APRH100000C; its page names no other colour of it: the other charging handles shown there are other models). In Aero's photo the handle, its latch and the latch's spring housing are one black; the latch's roll pin shows as a dot a few pixels across, which isn't drawn. Unmatched: sealed black anodize is the finish type's look."}},"components":{},"geometry":{"model":"aero-charging-handle.glb","components":{},"approximations":["Its plan is Aero's photo from above (the T's swept ends, the latch on its left reaching forward along the shaft, the nose), at two heights from the Army's drawing (8448518): the shaft and the block behind the shoulder at the shaft's thickness, the T's top .125 higher from where the drawing has it begin, with the drawing's arc cut in it where a receiver's rail's rounded end nests. The T's top is flat and its edges square but for a 0.012 in break: its forged rounding, seen from behind, isn't sourced.","The latch is drawn as part of the plan, one piece with the handle: behind the shoulder in the T, ahead of it its arm and hook at the reference model's height for it (its slot across the T, .100 over the shaft's underside, and its plate's .123: catch_bottom, catch_thickness); its pin and its spring aren't drawn, and the latch's own drawing (8448519) isn't in the package. The guide lugs are the plan's two bumps at the drawing's .119 (until 2026-10-20 at the shaft's whole thickness, out of the channel's tier). The shaft's top chamfers, the key's channel under it and the hook hanging below its front end (the drawing has all three; BCM's handle in the catalog is drawn with them) aren't drawn: they are inside the receiver.","The block's front corners beside the shaft are broken as the drawing has them, 47 degrees over .083 from the shaft's top and underside: an upper's notch has its own corners cut back at 45 degrees there (until 2026-10-20 they were square, and stood 0.07 in into those corners). Ahead of its shoulder it is cut by what of a forged upper stands beside it (2026-10-20, lib.handle_room): the walls either side of the channel's rear slot, out to the forging's side under the rail (std.ar15.rail_tongue_half_width, ±0.318), the left one less the Army drawing's latch slot, where the hook lies (8448524 Section D-D: .045 of wall left over the channel); and behind it the notch's front wall's two corners, cut back at 45 degrees. Its photos show the latch's arm and the shaft as one outline, where the wall between them is .045 to .109 thick: every handle on file had its arm drawn through it."],"ledger":["aero-charging-handle.length","aero-charging-handle.shaft_thickness","aero-charging-handle.t_height","aero-charging-handle.t_block_length","aero-charging-handle.t_nest_r","aero-charging-handle.t_nest_apex"]},"profiles":{"top":{"plane":"xz","origin":"the T's shoulder (its front face) on the shaft's centre line, +x toward the muzzle; the photo's up is the handle's left (-z)","offset":{},"points":[[-0.869,0.832],[-0.869,-0.64],[-0.862,-0.655],[-0.869,-0.662],[-0.869,-0.699],[-0.862,-0.706],[-0.862,-0.766],[-0.869,-0.788],[-0.862,-0.795],[-0.862,-0.854],[-0.854,-0.876],[-0.832,-0.921],[-0.784,-0.969],[-0.703,-1.006],[-0.621,-1.006],[-0.555,-0.976],[-0.518,-0.947],[-0.503,-0.947],[-0.47,-0.913],[-0.44,-0.862],[-0.44,-0.84],[-0.433,-0.832],[-0.433,-0.684],[-0.425,-0.677],[-0.433,-0.64],[-0.425,-0.632],[-0.418,-0.573],[-0.396,-0.521],[-0.381,-0.507],[-0.385,-0.496],[-0.396,-0.499],[-0.396,-0.492],[-0.374,-0.462],[-0.303,-0.399],[-0.237,-0.362],[-0.17,-0.34],[-0.126,-0.34],[-0.118,-0.333],[0,-0.333],[0.015,-0.325],[0.022,-0.207],[0.192,-0.207],[0.2,-0.2],[4.312,-0.2],[4.32,-0.207],[4.371,-0.207],[4.379,-0.2],[4.386,-0.207],[4.394,-0.2],[4.475,-0.2],[4.482,-0.207],[4.549,-0.214],[4.593,-0.229],[4.608,-0.244],[4.823,-0.244],[4.904,-0.207],[4.985,-0.207],[4.993,-0.2],[5.015,-0.207],[5.791,-0.207],[5.854,-0.152],[5.877,-0.115],[5.899,-0.041],[5.899,0.026],[5.891,0.033],[5.884,0.085],[5.862,0.129],[5.799,0.192],[4.948,0.192],[4.941,0.2],[4.882,0.207],[4.823,0.237],[4.749,0.237],[4.741,0.244],[4.608,0.244],[4.556,0.214],[4.512,0.2],[4.453,0.2],[4.445,0.192],[4.43,0.2],[4.379,0.192],[4.371,0.2],[4.334,0.2],[4.32,0.192],[4.312,0.2],[0.281,0.2],[0.266,0.192],[0.274,0.207],[0.366,0.285],[0.374,0.359],[0.366,0.374],[0.348,0.392],[0.325,0.399],[0.274,0.399],[0.266,0.407],[0.229,0.407],[0.222,0.414],[0.104,0.422],[0.059,0.436],[-0.104,0.451],[-0.111,0.459],[-0.133,0.459],[-0.2,0.496],[-0.248,0.558],[-0.263,0.603],[-0.263,0.64],[-0.285,0.669],[-0.285,0.684],[-0.274,0.695],[-0.259,0.695],[-0.24,0.721],[-0.255,0.751],[-0.237,0.769],[-0.222,0.769],[-0.211,0.788],[-0.218,0.832],[-0.181,0.854],[-0.174,0.899],[-0.181,0.906],[-0.189,0.95],[-0.222,0.991],[-0.259,1.013],[-0.325,1.021],[-0.333,1.028],[-0.385,1.028],[-0.392,1.036],[-0.451,1.036],[-0.459,1.043],[-0.54,1.05],[-0.577,1.036],[-0.607,0.991],[-0.725,0.991],[-0.777,0.969],[-0.84,0.906],[-0.854,0.884],[-0.862,0.84]],"scaleRefs":["aero-charging-handle.length"],"inputs":{"aero-charging-handle.length":5.895},"tolerance":0.005,"photo":"references/aero-charging-handle ad1e8e613ad3 (Aero's gallery: the charging handle from above, 1000 x 630)","method":"luminance < 200, largest piece, holes filled; frame from the reviewed holes shoulder, tip (135.2 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.005 in with the extremes kept: 136 points (IoU 0.998 with the full outline); checks: −y_min 1.006 ± 0.011 (tools/trace.py)","via":"harvest","note":"From above: the T with its swept ends, the latch on its left reaching forward along the shaft, the shaft to its hook."}},"gaps":[{"what":"Its latch","need":"The Army's drawing of the latch (8448519; the package has its parts list only), read and checked on Aero's photo: the handle's own (8448518) is read for its shaft, its T's heights, its lugs, its shoulder's breaks and the arc in its top, and the latch's height is the reference model's"}]},"aero-enhanced-15-handguard":{"id":"aero-enhanced-15-handguard","name":"AR15 15\" Enhanced M-LOK Handguard, Gen 2","manufacturer":"Aero Precision","sku":"APRA100218A","url":"https://www.aeroprecisionusa.com/ar15-15inch-mlok-handguard-bar-nut-gen2-1","category":"handguard","description":"Aero Precision's 15 in Enhanced free-float M-LOK handguard, second generation: \"Machined from 6061-T6 aluminum\", a \"Continuous top rail\" with \"Scalloped rails\", \"Quick disconnect sling socket at the 3, 6 and 9 o'clock positions\", held by eight screws to Aero's BAR interface. \"Our handguards use the BAR interface and do not work with a standard barrel nut. If you are using our M4E1 Enhanced Upper Receiver, no additional pieces are needed.\" Sold alone (APRA100218C) for that upper, and with the BAR barrel nut (APRA100218A) for \"a standard threaded upper receiver\". \"This handguard is specific to the AR15/M4E1 platform. It is not compatible with the M5 .308/M5E1 platform.\"","weight":"aero-enhanced-15-handguard.weight_with_nut","fitments":{"label":"Mounts","default":"bar_nut","options":{"bar_nut":{"label":"On a standard upper, with the BAR barrel nut","sku":"APRA100218A","params":{},"source":"https://www.aeroprecisionusa.com/ar15-15inch-mlok-handguard-bar-nut-gen2-1"},"enhanced":{"label":"On the M4E1 Enhanced upper (no nut)","sku":"APRA100218C","params":{"handguard_mount":{"nut":"aero-enhanced"}},"weight":"aero-enhanced-15-handguard.weight","source":"https://www.aeroprecisionusa.com/ar15-15inch-m-lok-handguard-gen2"}}},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"mount":{"origin":[0,0,0],"note":"The receiver's front face on the bore axis, +x toward the muzzle. Its own rear face is the barrel-nut thread's length behind this (rear_x), against the receiver's shoulder."},"mlok":{"origin":["{.rear_x} + {.mlok_slot0_from_rear}",0,0],"note":"On the handguard's axis (the bore's: its side flats stand half the published width either side of it) at the rearmost side M-LOK slot's centre (index 0), +x toward the muzzle; the faces are angles about this axis (M10)."},"mlok_bottom":{"origin":["{.rear_x} + {.mlok_slot0_from_rear}",0,0],"note":"The same axis at the underside's rearmost slot's centre, taken at the side rows' (the 15 in's underside isn't seen: mlok_bottom_slots)."},"top_rail":{"origin":["{.rear_x} + {.rail_slot0_from_rear}","{.rail_top_above_bore}",0],"note":"The rail's top at its rearmost slot's centre, +x toward the muzzle (picatinny: index = slot number). Its own rail: the receiver's is the receiver's."}},"interfaces":{"handguard_mount":{"type":"ar15.handguard_mount","role":"handguard","anchor":"mount","params":{"nut":"standard"},"flips":false,"note":"Aero, the page of every length: \"Are you attaching this handguard to a standard threaded upper receiver? Make sure to select \"Yes\" under the Bar Barrel Nut option above (shims included). Our handguards use the BAR interface and do not work with a standard barrel nut. If you are using our M4E1 Enhanced Upper Receiver, no additional pieces are needed.\" Its list of handguard lengths (2022, page 4): \"Our Enhanced Handguards were designed to work effortlessly with our M4E1 Enhanced Upper Receiver. Due to the integral handguard attachment point on the Enhanced Upper, these handguards install effortlessly with the use of eight screws.\" and \"*Can be used with mil-spec upper receivers with addition of BAR Barrel Nut.\" The BAR nut's page: \"Compatible with mil-spec threaded upper receivers ONLY.\" With the nut it is `standard`; alone it mounts only on the Enhanced upper's own platform (the other option)."},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}","beyond_seam":true,"seam_behind":"receiver","seam_ahead":"handguard"},"flips":false},"mlok":{"type":"mlok","role":"slots","anchor":"mlok","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_slots}","interval":"={std.mlok.interval}","face_distance":"={.width} / 2","bore":"={.inside_diameter}","reach_inside":"={.reach_inside}"},"faces":{"right":{"angle":90,"note":"the rifle's right side (+z)"},"left":{"angle":-90}},"flips":false,"note":"The two side flats, half the published width from the bore. How far an accessory's nuts may reach inside depends on the barrel and gas block under it, other parts: reach_inside has no figure, so that check reads as unmade."},"mlok_bottom":{"type":"mlok","role":"slots","anchor":"mlok_bottom","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_bottom_slots}","interval":"={std.mlok.interval}","face_distance":"={.bottom_below_bore}","bore":"={.inside_diameter}","reach_inside":"={.reach_inside}"},"faces":{"bottom":{"angle":180,"note":"the underside (6 o'clock)"}},"flips":false,"note":"The bottom flat, 0.9675 in below the bore. Wing Tactical: \"M-LOK slots at 3, 6, and 9 o'clock positions\". Its slots' count and stations are not seen on a 15 in in any photo on file and are taken as the side rows' (seven, from the same place), as a 12.63 in one's underside has its own: where a grip or a hand stop really bolts under it may differ by a slot."}},"materials":{"body":{"label":"Handguard","finish":"anodized","recolorable":true,"color":"placeholder-black","options":{"black":{"label":"Anodized Black","finish":"anodized","color":"placeholder-black","sku":"APRA100218C","source":"https://www.aeroprecisionusa.com/ar15-15inch-m-lok-handguard-gen2"},"fde":{"label":"FDE Cerakote","finish":"cerakote","color":"aero-fde-cerakote","sku":"APRA100294C","source":"https://www.aeroprecisionusa.com/ar15-enhanced-mlok-handguards"},"odg":{"label":"OD Green Anodized","finish":"anodized","color":"aero-od-green-anodize-6061","sheen":"matte","sku":"APRA100731C","source":"https://www.aeroprecisionusa.com/ar15-enhanced-mlok-handguards"},"kodiak":{"label":"Kodiak Brown Anodized","finish":"anodized","color":"aero-kodiak-brown-6061","sheen":"matte","sku":"APRA100732C","source":"https://www.aeroprecisionusa.com/ar15-enhanced-mlok-handguards"}},"default":"black","note":"Aero's words for each, on its page of every length: \"Anodized Black\", \"FDE Cerakote\", \"OD Green Anodized\", \"Kodiak Brown Anodized\" (Wing Tactical of the black: \"Black Hard Anodize\"; Impact Guns: \"Black Hard Coat Anodized\"). The numbers are the handguard alone's; with the BAR barrel nut the black one is APRA100218A and the FDE one APRA100294A, and the two anodized colours have no number with the nut (the choice of mounting, below, names the black's). The three colours are Aero's own presets, matched on its photos of its receivers (the Cerakote) and of its 15 in R-ONE handguard (the two dyed anodizes on 6061): this handguard's own photos of each (e729a8f2780d, d0498054eb7a, 9b7983046ad2) are the same tan, bronze olive and brown to the eye and weren't fitted again. The black is unmatched (sealed black anodize: its look is the finish type's)."},"screws":{"label":"Mounting screws","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The eight flat-head screws in their countersinks at the rear (Wing Tactical's box: \"8x Mounting Set Screws\"): dark grey to black steel in Wing's photo of them laid out beside the nut (a3dd964e9ad5) and in its photo of a 7.25 in handguard with them in (c08b544a7889). One kit for every colour of handguard; their finish isn't named on a page, and a black on steel isn't fitted to a photo. Aero's own photos are of the handguard off a rifle, its holes empty."},"socket":{"label":"Sling socket (6 o'clock)","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The quick-disconnect socket at 6 o'clock is a cup let into the bottom flat, a piece of its own: black under the bottom edge of the Kodiak Brown, the OD Green and the FDE handguards in Aero's photos of each (9b7983046ad2, d0498054eb7a, e729a8f2780d). The sockets at 3 and 9 o'clock are the handguard's own metal and colour. What the cup is made of isn't said on a page: drawn as black steel."}},"components":{},"geometry":{"model":"aero-enhanced-15-handguard.glb","components":{},"approximations":["Its section run from the tube's rear face to its front end: twelve flat faces about the bore under the rail's neck. A flat at 6 o'clock 0.88 in across; each side a shallow face (34 degrees from level) and a steep one (53) with a ridge between them 1.44 across and 0.79 from the bore's level; the side flats 0.93 high at the published 1.92 across; the same two faces above them; a shelf 0.235 in below the rail's top (read on Aero's level photo; the tube taken as high above the bore as its bottom flat is below it would have it at 0.245); the rail's neck. Read on Wing Tactical's view down its length from the rear, which is in perspective (the rear face is its nearest plane: across by the published width, up and down by the nut's four holes): each corner is good to 0.02 to 0.04 in, and the faces' angles to a few degrees. The published height (2.18) with the rail level with the receiver's puts the bottom flat 0.9675 below the bore, and half the width is 0.96. The corners are sharp: the photos show small rounds, inside and out.","Its rail is the standard's head in section (MIL-STD-1913's Figure 1) on a neck 0.67 across, with the channel under it (0.5 across, its roof 0.165 under the rail's top) open into the tube from end to end. Its 37 slots are the standard's size and pitch from the first's place on the side photo; behind the first tooth the rail runs back at its slots' floor to its rear end, and ahead of the last its floor runs out to the front end. Every other lug from the fifth is cut through by a window into the channel, 0.54 long and 0.36 across (Aero's \"Scalloped rails\"): their size and which lugs from the rear end are read on a view from above of a 12.63 in one, and on a 15 in they are carried on to the thirty-seventh lug, which its own three-quarter views bear out and no view from above counts. The blind pocket in the third lug isn't drawn.","Where it meets the receiver is its rail's rear end; the tube's rear face stands 0.11 in further back, round the receiver's front, and under where the rail would be it is notched 1.05 in wide from the bore's level up, which the receiver's own rail and the body under it stand in. That the tube reaches back is read on the side photos; the notch's width is worked out from where the tube's rear rim begins under the rail in the level side view (0.29 in below the rail's top), and no view shows it square on. Below the side flats' upper edges the tube's rear end leans forward, to 0.235 in at the bottom flat (the receiver's pivot lug stands under there): read on Aero's level photo and on the larger side photo (0.29 there), and drawn as one plane.","Inside: round at the published 1.78 in (the \"barrel nut cut\") for 1.6 in from the tube's rear face, a depth no page gives (bounded by the front screw holes and the first slots through the walls); ahead of it walls a tenth of an inch thick that follow the outside, the published 1.72 across the side flats. The muzzle end's photos show the walls so; that they are one thickness all round is assumed. As 6061 aluminium the model comes to 11.9 oz where Aero says 11.2.","Seven M-LOK slots in each side flat at the standard's size and pitch from the first's place on the side photo, and the same row along the bottom flat, which no view of a 15 in's underside shows: a 12.63 in one's has as many slots along the bottom as in a side, at the sides' stations (drawn so, and offered for mounting so: where a grip really bolts under it may differ by a slot). A row of fourteen shorter slots in each of the eight faces between (0.82 long, 0.2 across, 0.953 apart), the fourteenth ending a tenth of an inch short of the front end; each row down the middle of the shallow faces and toward the side flat on the steep ones, as the side photo has them.","The eight screws are drawn in: flat heads in countersinks on the four ridges at the rear, two on each, along the line from the bore. Their thread is read as a share of their heads on a seller's photo of them laid out; their sockets aren't drawn. The sling sockets at 3 and 9 o'clock are a boss on each side flat with the socket's hole through it; the one at 6 o'clock is a black cup let into the bottom flat. The cups' inner grooves aren't drawn.","Not drawn: the BAR barrel nut (it is inside the rear end, behind the receiver's face, and shows from nowhere on a rifle) and its shims; the scallops milled along the flats' edges (Aero: \"Additional milling along flats to aid with gripping and add visual appeal\": small crescent cuts 0.527 in apart along each edge of the side flats, read and in the ledger); the anti-rotation tabs; the bevel round the rear end; the markings (the A and the M-LOK mark on each side)."],"ledger":["aero-enhanced-15-handguard.length","aero-enhanced-15-handguard.overall_length","aero-enhanced-15-handguard.width","aero-enhanced-15-handguard.height","aero-enhanced-15-handguard.inside_diameter","aero-enhanced-15-handguard.nut_cut_diameter","aero-enhanced-15-handguard.nut_cut_depth","aero-enhanced-15-handguard.side_flat_height","aero-enhanced-15-handguard.ridge_across","aero-enhanced-15-handguard.ridge_from_bore","aero-enhanced-15-handguard.bottom_flat_width","aero-enhanced-15-handguard.neck_width","aero-enhanced-15-handguard.channel_width","aero-enhanced-15-handguard.shelf_below_rail_top","aero-enhanced-15-handguard.rear_x","aero-enhanced-15-handguard.rear_bottom_ahead","aero-enhanced-15-handguard.rear_notch_width"]},"profiles":{"side":{"plane":"xy","origin":"the tube's rear face and the rail's top","offset":{"x":"rear_x","y":"rail_top_above_bore"},"points":[[0,-0.325],[0,-0.525],[0.017,-0.542],[0.017,-0.742],[0.033,-0.759],[0.05,-1.109],[0.067,-1.125],[0.083,-1.459],[0.1,-1.476],[0.1,-1.626],[0.117,-1.642],[0.117,-1.759],[0.133,-1.776],[0.15,-2.009],[0.217,-2.093],[0.217,-2.126],[0.242,-2.168],[0.275,-2.184],[2.576,-2.184],[2.676,-2.268],[3.16,-2.268],[3.243,-2.184],[14.815,-2.184],[14.832,-2.168],[14.965,-2.168],[14.982,-2.184],[14.998,-2.168],[15.015,-2.184],[15.057,-2.159],[15.09,-2.076],[15.107,-1.876],[15.123,-1.859],[15.123,-1.542],[15.14,-1.526],[15.14,-0.859],[15.123,-0.842],[15.123,-0.592],[15.107,-0.575],[15.107,-0.442],[15.09,-0.425],[15.09,-0.358],[15.057,-0.292],[15.057,-0.025],[15.032,0],[14.998,-0.017],[14.832,-0.017],[14.815,-0.133],[14.715,-0.133],[14.706,-0.025],[14.681,0],[14.648,-0.017],[14.631,0],[14.598,0],[14.581,-0.017],[14.448,-0.017],[14.44,-0.125],[14.331,-0.133],[14.306,-0.092],[14.323,-0.075],[14.298,-0.017],[14.265,0],[14.248,-0.017],[14.181,-0.017],[14.165,0],[14.148,-0.017],[14.056,-0.025],[14.056,-0.108],[14.031,-0.133],[13.948,-0.133],[13.923,-0.108],[13.923,-0.025],[13.898,0],[13.881,-0.017],[13.681,-0.017],[13.673,-0.075],[13.656,-0.092],[13.673,-0.108],[13.648,-0.133],[13.548,-0.133],[13.539,-0.042],[13.514,-0.017],[13.298,-0.017],[13.273,-0.042],[13.289,-0.058],[13.273,-0.075],[13.264,-0.133],[13.164,-0.133],[13.139,-0.075],[13.156,-0.058],[13.131,-0.017],[12.914,-0.017],[12.889,-0.042],[12.881,-0.133],[12.764,-0.133],[12.747,-0.017],[12.514,-0.017],[12.497,-0.133],[12.38,-0.133],[12.364,-0.017],[12.13,-0.017],[12.114,-0.133],[11.997,-0.133],[11.972,-0.108],[11.964,-0.017],[11.747,-0.017],[11.73,-0.133],[11.597,-0.133],[11.58,-0.017],[11.363,-0.017],[11.338,-0.042],[11.33,-0.133],[11.213,-0.133],[11.188,-0.108],[11.205,-0.092],[11.188,-0.075],[11.18,-0.017],[10.963,-0.017],[10.946,-0.133],[10.83,-0.133],[10.805,-0.108],[10.796,-0.017],[10.58,-0.017],[10.563,-0.133],[10.43,-0.133],[10.421,-0.058],[10.396,-0.017],[10.196,-0.017],[10.179,-0.133],[10.029,-0.133],[10.013,-0.017],[9.813,-0.017],[9.788,-0.042],[9.779,-0.133],[9.646,-0.133],[9.629,-0.017],[9.412,-0.017],[9.396,-0.133],[9.246,-0.133],[9.229,-0.017],[9.029,-0.017],[9.012,-0.133],[8.862,-0.133],[8.854,-0.042],[8.829,-0.017],[8.645,-0.017],[8.62,-0.042],[8.612,-0.133],[8.462,-0.133],[8.445,-0.017],[8.245,-0.017],[8.229,-0.133],[8.079,-0.133],[8.045,-0.017],[7.862,-0.017],[7.845,-0.133],[7.678,-0.133],[7.662,-0.017],[7.478,-0.017],[7.453,-0.042],[7.445,-0.133],[7.295,-0.133],[7.27,-0.092],[7.262,-0.017],[7.078,-0.017],[7.061,-0.133],[6.895,-0.133],[6.878,-0.017],[6.695,-0.017],[6.67,-0.042],[6.661,-0.133],[6.511,-0.133],[6.486,-0.108],[6.478,-0.017],[6.294,-0.017],[6.294,-0.133],[6.111,-0.133],[6.086,-0.075],[6.103,-0.058],[6.094,-0.017],[5.911,-0.017],[5.894,-0.133],[5.711,-0.133],[5.694,-0.017],[5.511,-0.017],[5.511,-0.133],[5.327,-0.133],[5.302,-0.108],[5.294,-0.017],[5.127,-0.017],[5.111,-0.133],[4.927,-0.133],[4.91,-0.017],[4.727,-0.017],[4.719,-0.042],[4.735,-0.058],[4.735,-0.108],[4.71,-0.133],[4.544,-0.133],[4.519,-0.108],[4.51,-0.017],[4.344,-0.017],[4.327,-0.133],[4.143,-0.133],[4.127,-0.1],[3.968,-0.092],[4.01,-0.067],[4.027,-0.083],[4.11,-0.083],[4.135,-0.025],[4.127,-0.017],[3.96,-0.017],[3.952,-0.108],[3.927,-0.133],[3.743,-0.133],[3.727,-0.017],[3.56,-0.017],[3.543,-0.133],[3.36,-0.133],[3.335,-0.108],[3.343,-0.017],[3.16,-0.017],[3.151,-0.075],[3.243,-0.083],[3.243,-0.1],[3.16,-0.1],[3.143,-0.133],[2.96,-0.133],[2.943,-0.017],[2.776,-0.017],[2.751,-0.075],[2.768,-0.108],[2.743,-0.133],[2.559,-0.133],[2.559,-0.017],[2.376,-0.017],[2.368,-0.108],[2.343,-0.133],[2.176,-0.133],[2.159,-0.017],[1.976,-0.017],[1.959,-0.133],[1.776,-0.133],[1.767,-0.075],[1.784,-0.042],[1.759,-0.017],[1.592,-0.017],[1.567,-0.042],[1.584,-0.075],[1.559,-0.133],[1.392,-0.133],[1.384,-0.025],[1.359,0],[1.342,-0.017],[1.192,-0.017],[1.184,-0.108],[1.159,-0.133],[0.992,-0.133],[0.984,-0.025],[0.959,0],[0.942,-0.017],[0.792,-0.017],[0.784,-0.108],[0.759,-0.133],[0.609,-0.133],[0.592,-0.017],[0.559,0],[0.525,-0.017],[0.442,-0.017],[0.409,0],[0.384,-0.025],[0.384,-0.075],[0.442,-0.083],[0.442,-0.1],[0.392,-0.1],[0.375,-0.133],[0.192,-0.133],[0.183,-0.292],[0.025,-0.3]],"scaleRefs":["aero-enhanced-15-handguard.overall_length"],"inputs":{"aero-enhanced-15-handguard.overall_length":15.14},"tolerance":0.01,"photo":"references/aero-enhanced-15-handguard 9b7983046ad2 (Aero: the 15 in Kodiak Brown Enhanced handguard's right side, level, 1000 x 630)","method":"luminance < 225, largest piece, holes filled; scale from aero-enhanced-15-handguard.overall_length = 15.14 in (x-extent 908 px → 60.0 px/in); origin at x min, y max of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 278 points (IoU 0.999 with the full outline) (tools/trace.py)","via":"harvest","note":"The slots are inside the outline (its holes filled); the model cuts them. The 6 o'clock socket's cup hangs under the bottom edge behind the first M-LOK slot."}},"gaps":[{"what":"Whether a clamp that hangs low beside a rail clears the tube's top (0.235 in under the rail's top as read; Aimpoint's LRP and EOTECH's STS mount hang 0.37 to 0.39 in as drawn, and stand in it; Magpul's MBUS 3 sights' hooks by a few thousandths of a cubic inch: app/tests/rail-clamps.test.ts)","need":"A photo of such a mount on this handguard's rail, or a sentence of Aero's on what its rail takes"},{"what":"The room inside its faces before the barrel (reach_inside: what an M-LOK accessory's nuts may take)","need":"The barrel's and the gas block's size under it, from the parts a build puts there"},{"what":"The M-LOK row along its underside (taken at the sides' stations with the sides' count, as a 12.63 in one's is: a grip under it may really bolt a slot off)","need":"A view of a 15 in's underside"},{"what":"Its section square on (each corner is read on a view in perspective, to 0.02 to 0.04 in), the rounds at its corners and the notch under its rail's rear end","need":"An end view taken from far off with a known size in frame, or a drawing; a view of its rear end from straight behind with no nut in it"},{"what":"How deep its barrel nut cut is, and what the BAR barrel nut's own sizes are (only its weight and the barrels it takes are published)","need":"The nut's length from a photo of it beside a rule, or Aero's drawing"},{"what":"How much room a clamp's jaws have under its rail's head: the tube's top stands 0.235 in below the rail's top beside the neck by two photos, and three clamps on file whose hooks reach 0.37 to 0.39 in below a rail's top (Aimpoint's Micro T-2 mount, EOTECH's G33 and G45 mounts) share space with the tube there as drawn","need":"Its section from a drawing, or a photo of one of those mounts on this rail"},{"what":"Which of its rail's lugs are cut through along a 15 in (carried on from a 12.63 in one's pattern), and the pocket in the third","need":"A view of a 15 in from straight above"},{"what":"The scallops milled along its flats' edges (their pitch and first station are read; their depth and outline aren't, and they aren't drawn)","need":"A close view of a flat's edge square on and one along it"},{"what":"Its weight with the nut, the eight screws and the shims on (Aero's two figures added: the screws and shims aren't weighed)","need":"A weight for the screw kit, or for the number APRA100218A as boxed less its carton"}]},"aero-m4e1-enhanced-upper":{"id":"aero-m4e1-enhanced-upper","name":"M4E1 Enhanced Upper Receiver Stripped","manufacturer":"Aero Precision","sku":"APAR600201C","url":"https://www.aeroprecisionusa.com/ar15-m4e1-enhanced-upper-receiver-stripped","category":"upper","description":"Aero Precision's M4E1 Enhanced stripped upper: \"a one-piece design combining the handguard mounting platform with the upper itself\", \"Machined from 7075-T6 forged aluminum\", \"M4 Feedramps\", \".250 takedown pin holes\". \"Handguard mounting platform is forged into the receiver\"; \"Compatible with Aero Precision Enhanced and Quantum Series handguards but also fits most BAR-system handguards\"; \"Works with standard AR15/M16 components\". Sold without a port door, a forward assist or a barrel nut (\"NOTE: This Upper Receiver will NOT ship with a barrel nut.\").","weight":"aero-m4e1-enhanced-upper.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"pins":{"origin":[0,0,0]},"front_face":{"origin":["{.front_face_x}","{.bore_axis_above_pin}",0],"note":"Where a barrel extension's flange seats, inside the platform, on the bore axis, +x toward the muzzle: the standard's place for a receiver's front face, and where a handguard is placed from (its rail's rear end meets this receiver's shoulder, the barrel-nut thread's length behind)."},"rear_face":{"origin":["{.receiver_rear_x}","{.bore_axis_above_pin}",0],"note":"The rear face on the bore axis, +x toward the muzzle: the bolt carrier's channel opens here."},"handle_channel":{"origin":["{.handle_seat_x}","{.bore_axis_above_pin} + {.charging_handle_above_bore}",0],"note":"The charging handle's seat on its channel's axis, +x toward the muzzle: the front wall of the open notch under the rail's rear end, at the notch's mid-height."},"top_rail":{"origin":["{.rail_slot0_x}","{.rail_top_above_pin}",0],"note":"The rail's top at its rearmost slot's centre, +x toward the muzzle (picatinny: index = slot number)."}},"interfaces":{"receiver_pins":{"type":"ar15.upper_lower","role":"upper","anchor":"pins","params":{"pin_spacing":"={std.ar15.pin_spacing}"},"flips":false},"barrel_extension":{"type":"ar15.barrel_extension","role":"receiver","anchor":"front_face","params":{},"flips":false},"handguard_mount":{"type":"ar15.handguard_mount","role":"receiver","anchor":"front_face","params":{"nut":"aero-enhanced"},"flips":false,"note":"Aero: \"This M4E1 upper receiver is a one-piece design combining the handguard mounting platform with the upper itself. Through superior engineering, we have condensed the parts needed to mount a free-floated handguard to a mere 8 screws.\"; \"Handguard mounting platform is forged into the receiver\"; \"Compatible with Aero Precision Enhanced and Quantum Series handguards but also fits most BAR-system handguards\". Its BAR barrel nut's page: \"If you have our M4E1 Enhanced Upper Receiver, you do not need a BAR Barrel Nut as the barrel nut and rail mounting platform are forged directly on to the upper receiver itself.\" It has no barrel-nut thread for a standard handguard's nut."},"carrier_channel":{"type":"ar15.carrier_channel","role":"receiver","anchor":"rear_face","params":{},"flips":false},"charging_handle_channel":{"type":"ar15.charging_handle_channel","role":"receiver","anchor":"handle_channel","params":{},"flips":false},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}","seam":"={.rail_front_x} - {.rail_slot0_x}","seam_parts":"the receiver's rail and the handguard's","seam_behind":"receiver","seam_ahead":"handguard"},"flips":false,"note":"Its own rail of 14 slots, counted on its side photo; an Enhanced handguard's rail ahead of it is the handguard's own."}},"materials":{"receiver":{"label":"Receiver","finish":"anodized","recolorable":true,"color":"placeholder-black","options":{"black":{"label":"Anodized Black","finish":"anodized","color":"placeholder-black","sku":"APAR600201C","source":"https://www.aeroprecisionusa.com/ar15-m4e1-enhanced-upper-receiver-stripped"},"fde":{"label":"FDE Cerakote","finish":"cerakote","color":"aero-fde-cerakote","sku":"APAR600202C","source":"https://www.aeroprecisionusa.com/ar15-m4e1-enhanced-upper-receiver-stripped-fde"}},"default":"black","note":"Aero's Finish rows: \"Anodized Black\" and \"Magpul FDE Cerakote\" (its FDE page's title: \"M4E1 Enhanced Upper Receiver Stripped - FDE Cerakote\"). The FDE is Aero's own preset, matched on its photos of the M4E1 Threaded receiver in the same coat; this receiver's own FDE picture (21a7326ba5f0) is the same tan to the eye and wasn't fitted again. The assembled Enhanced upper is named in other colours on sellers' pages; no page for a stripped one in them is on file. The black is unmatched (sealed black anodize: its look is the finish type's)."}},"components":{},"geometry":{"components":{"receiver":"aero-m4e1-enhanced-upper.receiver.glb"},"approximations":["Behind its front shoulder it is the M4E1 Threaded receiver's model, from the same figures (this part's ledger takes them from that part's by reference), on this receiver's own side outline (AR15Discounts' straight right side, framed by its lug holes): the two receivers' outlines agree within 0.025 in behind the shoulder, and the Threaded receiver's forward assist housing and deflector outlines, carried through the two pin frames, lie on this one's. So what is said of that model is said of this one: the rail's lower faces the standard's; a flat band each side under the rail's neck and a flat face sloping out to the body's widest (the M4E1's \"billet look\"); below the bore's level the mil-spec forging's round body, which no view on file shows of this receiver; its rear lower corner on the arc a lower's rear walls rise along; the forward assist housing a flat-faced block and the deflector flat faces out to one point, their reach read on a small photo of the Threaded receiver from above. Its left side is in two views on file and has the same band and sloped face. Its rail's tongue, the charging handle's channel, its notch and the latch's slot are the Threaded receiver's, the standard's (2026-10-20).","The platform is a plain round about the bore from the shoulder (the standard's place for the foot of a barrel-nut thread; this receiver's own photo reads it 0.006 in ahead) to its front face 1.33 in on, at the diameter its own side photo reads (1.77 in: Aero's handguard for it is bored 1.78 there). Six grooves are cut straight across its top, a tenth of an inch wide and an eighth deep, a fifth of an inch apart, as the side photo has them (how far round they run is seen only in a three-quarter view: they end between the two upper rows of screw holes, as a straight cut would). Eight screw holes, two along each of its four diagonals, where the right side's four show; the left side's are their mirror.","It is bored at its front for a barrel nut, back to where the barrel's flange seats, at the size of the nut in the photos (1.22 in: the least it can be); its thread isn't drawn. The barrel's seat is taken at the standard's place for a receiver's front face (inside the platform, in no photo): the barrel has to stand where a standard bolt carrier and magazine meet it.","Its left side (2026-10-13), as the M4E1 Threaded receiver's and from its figures by reference (read there on Aero's left view of the FDE receiver): a flat upright pad along the foot of the wall from 3.08 to 6.20 in ahead of the takedown pin, its upper edge 0.66 above the pin line, with a middle length from 4.05 to 4.585 that stands further out and reaches 0.74; and the cam pin's boss, 5.14 ahead: an upright outer face 0.34 long from 1.21 to 1.52 above the pin line with a flat flank each side, a face sloping back from it to the band at 1.65, and an end each side sloping down to the band, 0.75 across. This receiver's own left view (Aero's assembled one, black: creases and lit lines two or three levels from the wall's tone) has the same pad in its three lengths and the same boss: their heights and lengths within 0.012 in of that receiver's (one, 0.024) and the distances between them within 0.01, and all of them 0.03 to 0.04 in further back along the receiver, which is inside the two readings' ± together and isn't settled (the wall is half an inch nearer the lens than what frames either photo). How far they stand out is in no view on file: each face is upright, and is drawn where the body as drawn is at the height of the edge it runs out on (the pad 0.096 and 0.121 in out from the lug wall, the boss 0.068 from the band). The boss's two flanks are drawn alike, its ends' undersides and the pad's ends square, and the face over the boss one flat.","Not drawn: the barrel nut that stands in the platform's front in every picture (Aero: \"This Upper Receiver will NOT ship with a barrel nut\"), the small screw low on the platform's right side, the flats and breaks on the platform's sides and the chamfer round its front, the port's door seat and hinge bosses, and the markings."],"ledger":["aero-m4e1-enhanced-upper.receiver_rear_x","aero-m4e1-enhanced-upper.shoulder_x","aero-m4e1-enhanced-upper.front_face_x","aero-m4e1-enhanced-upper.platform_front_x","aero-m4e1-enhanced-upper.platform_od","aero-m4e1-enhanced-upper.platform_bore_d","aero-m4e1-enhanced-upper.underside_y","aero-m4e1-enhanced-upper.rail_top_above_pin","aero-m4e1-enhanced-upper.bore_axis_above_pin","aero-m4e1-enhanced-upper.side_half_width","aero-m4e1-enhanced-upper.fa_housing_out_rear","aero-m4e1-enhanced-upper.deflector_out","aero-m4e1-enhanced-upper.left_pad_top_y","aero-m4e1-enhanced-upper.cam_boss_bottom_y"]},"profiles":{"side":{"plane":"xy","origin":"the takedown pin centre (the rifle frame origin), +x toward the muzzle","offset":{},"points":[[-0.657,1.25],[-0.641,1.135],[-0.646,0.923],[-0.597,0.727],[-0.532,0.586],[-0.472,0.51],[-0.365,0.409],[-0.238,0.33],[-0.237,-0.094],[-0.226,-0.208],[-0.213,-0.216],[0.234,-0.211],[0.236,0.227],[0.255,0.241],[6.122,0.252],[6.146,0.244],[6.146,-0.001],[6.163,-0.072],[6.231,-0.167],[6.34,-0.221],[6.46,-0.221],[6.53,-0.188],[6.593,-0.099],[6.601,-0.02],[7.869,-0.013],[7.899,0.028],[7.92,0.256],[7.994,0.276],[8.018,0.354],[8.013,0.436],[7.928,0.466],[7.925,0.501],[8.004,0.504],[8.029,0.523],[8.034,0.632],[8.034,0.763],[7.966,0.771],[7.936,0.795],[7.936,0.964],[8.034,0.975],[8.028,1.22],[7.925,1.252],[7.927,1.293],[7.987,1.293],[8.017,1.312],[8.023,1.394],[8.012,1.454],[7.987,1.489],[7.919,1.497],[7.886,1.753],[7.856,1.777],[7.786,1.777],[7.767,1.649],[7.693,1.641],[7.68,1.655],[7.674,1.769],[7.584,1.777],[7.571,1.649],[7.481,1.646],[7.473,1.769],[7.383,1.777],[7.369,1.649],[7.296,1.641],[7.277,1.649],[7.271,1.769],[7.187,1.777],[7.173,1.763],[7.168,1.649],[7.084,1.641],[7.07,1.769],[6.986,1.777],[6.967,1.649],[6.888,1.64],[6.869,1.659],[6.869,1.768],[6.784,1.776],[6.771,1.746],[6.771,1.654],[6.752,1.64],[6.681,1.64],[6.667,1.654],[6.662,1.768],[6.596,1.784],[6.602,2.084],[6.588,2.097],[6.397,2.086],[6.403,1.983],[6.256,1.972],[6.204,1.98],[6.191,2.092],[6.033,2.097],[5.998,2.072],[6.014,2.012],[6.006,1.977],[5.886,1.971],[5.807,1.98],[5.807,2.078],[5.783,2.097],[5.625,2.091],[5.6,2.066],[5.617,2.05],[5.614,1.977],[5.494,1.971],[5.41,1.979],[5.41,2.083],[5.391,2.096],[5.244,2.096],[5.214,2.072],[5.225,1.984],[5.189,1.971],[5.015,1.976],[5.004,2.09],[4.846,2.096],[4.822,2.077],[4.819,1.976],[4.683,1.97],[4.615,1.978],[4.607,2.09],[4.455,2.095],[4.43,2.082],[4.428,1.976],[4.248,1.97],[4.218,1.984],[4.215,2.09],[4.041,2.09],[4.025,1.97],[3.829,1.97],[3.818,2.089],[3.671,2.095],[3.641,2.081],[3.633,1.975],[3.502,1.969],[3.429,1.983],[3.429,2.081],[3.399,2.094],[3.252,2.089],[3.236,1.974],[3.051,1.974],[3.032,1.982],[3.037,2.075],[3.018,2.094],[2.876,2.094],[2.847,2.08],[2.844,1.974],[2.659,1.968],[2.634,1.982],[2.645,2.075],[2.626,2.094],[2.468,2.093],[2.449,2.08],[2.441,1.968],[2.256,1.968],[2.243,1.982],[2.245,2.082],[2.076,2.093],[2.057,2.079],[2.049,1.973],[1.864,1.968],[1.851,1.976],[1.862,2.019],[1.851,2.041],[1.867,2.058],[1.853,2.082],[1.679,2.093],[1.66,2.079],[1.652,1.973],[1.483,1.967],[1.453,1.976],[1.47,1.992],[1.462,2.082],[1.282,2.092],[1.268,2.079],[1.263,1.975],[1.228,1.967],[1.059,1.978],[1.078,1.986],[1.083,2.062],[1.037,2.092],[-0.536,2.091],[-0.579,2.085],[-0.604,2.055],[-0.609,1.925],[-0.595,1.911],[-0.552,1.911],[-0.525,1.889],[0.014,1.89],[0.088,1.816],[0.088,1.664],[0.009,1.58],[-0.628,1.579],[-0.641,1.544]],"features":{"forward_assist_housing":[[[-0.631,1.448],[1.773,1.45],[1.899,1.349],[1.9,0.845],[1.522,0.718],[0.009,0.524],[-0.496,0.507],[-0.63,0.658]]],"deflector":[[[1.874,1.366],[2.32,1.585],[2.555,1.669],[2.74,1.619],[2.95,1.468],[2.951,0.846],[2.53,0.846],[1.899,1.097]]]},"scaleRefs":["std.ar15.pin_spacing"],"inputs":{"std.ar15.pin_spacing":6.375},"tolerance":0.01,"photo":"references/aero-m4e1-enhanced-upper 841632838fda (AR15Discounts 324831.png: the M4E1 Enhanced stripped upper's right side, straight on, 1920 x 1280)","method":"luminance < 200, largest piece, holes filled; frame from the reviewed holes takedown, pivot (183.8 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.01 in with the extremes kept: 191 points (IoU 0.995 with the full outline); checks: x_min -0.657 ± 0.008 in vs aero-m4e1-enhanced-upper.receiver_rear_x -0.621 ± 0.005 (conflict): DISAGREES; y_max 2.097 ± 0.009 in vs aero-m4e1-enhanced-upper.rail_top_above_pin 2.088 ± 0.02 (provisional): agrees; features through the same placement (forward_assist_housing: the housing's outline from the right, the bore's opening at its rear (the M4E1 Threaded receiver's outline, carried over and looked at on this photo); deflector: the brass deflector: its ridge up to the apex, down to the port's rear corner (the M4E1 Threaded receiver's outline, carried over and looked at on this photo)) (tools/trace.py)","via":"harvest","note":"Its outer silhouette with the lug holes filled: the platform at its front with the grooves across its top and a barrel nut's lugs standing out of its front face, the ejection port and the forward assist inside it."}},"gaps":[{"what":"Its weight is worked out, not published (no page states the stripped receiver's: Aero's 6.9 oz for the Threaded receiver plus the platform's metal, 10 oz ± 1)","need":"A page of Aero's or a seller's for APAR600201C that states it"},{"what":"The platform square on: its flats, how far round its grooves run, the eight holes' angle and size, the thread in its front and where inside it the barrel seats","need":"A view of it from straight ahead and one from above with a known size in frame, or Aero's drawing"},{"what":"Its section below the bore's level (as the M4E1 Threaded receiver's gap)","need":"A view of it square from the front or the rear with a known size in frame"},{"what":"How far its left side's pad and cam pin boss stand out (each is drawn where the body as drawn is at the height of the edge it runs out on), the shape of the pad's ends and of the boss's flanks and undersides; and where along the receiver they are to better than 0.04 in (its own left view reads them that far behind the Threaded receiver's)","need":"A view from above, from below or from an end that shows the left wall in profile at a size to read; a left view of the stripped receiver in a colour that shows relief (its FDE one), square on, with the lens's place known from its own holes"}]},"aero-m4e1-lower":{"id":"aero-m4e1-lower","name":"M4E1 complete lower, A2 grip and M4 stock","manufacturer":"Aero Precision","sku":"APAR600101","url":"https://www.aeroprecisionusa.com/m4e1-complete-lower-a2-grip-m4-stock-black","category":"lower","description":"Aero's enhanced forging with an integrated trigger guard, a flared magwell, a threaded bolt catch pin and an upper tension screw, sold complete: a mil-spec lower parts kit, an A2 grip, a carbine receiver extension with its buffer and spring, and an M4 stock, installed. One product over the lower's slots (D33); drawn as photographed, with the stock at the position Aero's photo shows.","weight":"aero-m4e1-lower.weight","mass":{"note":"Aero publishes the complete lower's 33.25 oz, and for two of the parts it ships with their own weights sold alone: the M4 stock, 7.2 oz, at its model's centroid (the patent's section and plan, 2026-10-02), and the carbine buffer kit (extension, buffer, spring, end plate and castle nut), 9.8 oz, as a tube at the standard's OD running the generic carbine length back from the receiver's rear face. The receiver takes the rest, with the grip and the parts kit in it.","lumps":{"stock":{"component":"stock","weight":"aero-m4e1-lower.stock_weight"},"extension_kit":{"tube":{"from":["{.rear_face_x}","{.buffer_axis_above_pin}",0],"to":["{.rear_face_x} - {.extension_length}","{.buffer_axis_above_pin}",0],"od":"{std.receiver_extension.milspec_od}"},"weight":"aero-m4e1-lower.buffer_kit_weight"},"receiver":{"component":"receiver","rest":true}}},"occupies":["lpk","trigger","trigger_guard","grip","receiver_extension","end_plate","castle_nut","buffer","buffer_spring","stock"],"integral":[],"brings":["selector"],"seats":{},"requires":[],"anchors":{"pins":{"origin":[0,0,0],"note":"The rifle frame origin."},"buffer_tube_mount":{"origin":[0,"{.buffer_axis_above_pin}",0],"x":[-1,0,0]},"magwell":{"origin":["{.magazine_seat_x}","{std.ar15.mag_catch_slot_bottom_y} + {std.ar15.mag_catch_slot_h}",0],"note":"Where a seated magazine hangs: x where its spine's rear face sits in the well (magazine_seat_x), y at the catch's upper face, which is the top of the slot the catch comes through (the Army's drawing). A magazine's own anchor is the upper edge of its catch notch, so each hangs by its own. Until 2026-10-05 this was the feed lips' top of a seated Black Dog (magazine_seat_y, still in the ledger as that), and a PMAG, whose notch is 0.37 in nearer its top, hung that much too high: its lips above the bore."},"grip_lug":{"origin":[0,"{.grip_seat_y}",0]},"trigger_guard":{"origin":["{.trigger_guard_front_x}","{.trigger_guard_front_y}",0],"x":["{.trigger_guard_front_x} - {.trigger_guard_rear_x}","{.trigger_guard_front_y} - {.trigger_guard_rear_y}",0]},"fcg":{"origin":["{.trigger_pin_x}","{.trigger_pin_y}",0]},"lpk":{"origin":[0,0,"-{std.ar15.lower_body_width} / 2"]},"selector":{"origin":["{std.ar15.selector_x}","{std.ar15.selector_y}",0],"note":"The selector's hole (the Army's drawing 8448608), on its axis at the receiver's mid-plane: a selector chosen on its own turns here (D86). Aero, of the M4E1: \"Marked and milled to accept short-throw safety selectors, but will work with standard selectors as well.\""},"face":{"origin":["{.trigger_face_x}","{.trigger_pin_y}",0],"note":"The trigger's face, where a finger lands: length of pull is read from here (the trigger slot is occupied by this product)."},"butt":{"origin":["-{.butt_behind_pin}","{.buffer_axis_above_pin}",0],"note":"The butt's plane on the tube axis, at the position the stock is drawn at (the stock slot is occupied by this product)."}},"interfaces":{"receiver_pins":{"type":"ar15.upper_lower","role":"lower","anchor":"pins","params":{"pin_spacing":"={std.ar15.pin_spacing}"},"flips":false},"buffer_tube_mount":{"type":"ar15.buffer_tube_mount","role":"receiver","anchor":"buffer_tube_mount","params":{},"flips":false},"magwell":{"type":"ar15.magwell","role":"receiver","anchor":"magwell","params":{"family":"5.56"},"flips":false,"note":"A standard AR15 magwell (Aero: compatible with all mil-spec AR15 parts; the flare is the mouth)."},"grip_lug":{"type":"ar15.grip_lug","role":"receiver","anchor":"grip_lug","params":{},"flips":false},"trigger_guard":{"type":"ar15.trigger_guard","role":"receiver","anchor":"trigger_guard","params":{},"flips":false},"fcg":{"type":"ar15.fcg","role":"receiver","anchor":"fcg","params":{"pin_diameter":"small-pin"},"flips":false,"note":"Sold with a \"Mil-spec Lower Parts Kit\" (Aero's page): standard .154 in pins. The trigger slot is occupied, so nothing mates here."},"lpk":{"type":"ar15.lpk","role":"receiver","anchor":"lpk","params":{},"flips":false},"selector":{"type":"ar15.selector","role":"receiver","anchor":"selector","params":{},"flips":false}},"materials":{"receiver":{"label":"Receiver","finish":"anodized","recolorable":true,"color":"placeholder-black","sheen":"matte","options":{"black":{"label":"Anodized Black","finish":"anodized","color":"placeholder-black","sheen":"matte","sku":"APAR600101","source":"https://www.aeroprecisionusa.com/m4e1-complete-lower-a2-grip-m4-stock-black"},"fde":{"label":"FDE Cerakote","finish":"cerakote","color":"aero-fde-cerakote","sku":"APAR600102","source":"https://www.aeroprecisionusa.com/m4e1-complete-lower-a2-grip-m4-stock-fde"}},"default":"black","note":"\"Anodized Black\" (Aero); the other's Finish row is \"Magpul FDE Cerakote\" and it \"Includes: M4E1 Stripped Lower Receiver - FDE Cerakote, M4 Stock - Black, A2 Grip - Black, Mil-spec Lower Parts Kit, Carbine Receiver Extension\". The colourway is the receiver's alone: in Aero's photo of APAR600102 the grip, the stock, the castle nut and end plate, the pins' heads, the selector, the catches and the trigger are as black as on the black one, so no other slot follows it. Aero's list of complete lowers was read to its first page (the rest is behind an address its robots.txt refuses): no other colour of this one, with the A2 grip and M4 stock, was found."},"grip":{"label":"A2 grip","finish":"polymer","recolorable":false,"color":"placeholder-polymer-black","note":"\"A2 Grip - Black\" (Aero's page, and the FDE Cerakote one's \"Includes\" list): the same black plastic under either receiver (Aero's photos of APAR600101 and APAR600102). Unmatched: a black."},"stock":{"label":"M4 stock","finish":"polymer","recolorable":false,"color":"placeholder-polymer-black","note":"\"M4 Stock - Black\" (Aero's page, and the FDE Cerakote one's \"Includes\" list): the same black plastic under either receiver, its latch and sling loop dark steel (Aero's photos of APAR600101 and APAR600102; they aren't drawn apart). Unmatched: a black."},"controls":{"label":"Controls","finish":"steel","recolorable":false,"color":"placeholder-black","note":"Its \"mil-spec lower parts kit\" (Aero's page): the pins' heads, the selector, the bolt catch and the magazine release, drawn as the Rise kit's (geometry.controls). Dark steel on both receivers: against the FDE Cerakote they read black, against the black anodize a little greyer than it (Aero's two photos, looked at at full size 2026-10-06). Aero doesn't name their finish; the colour is a placeholder, and the slot follows nothing."},"tube":{"label":"Receiver extension","finish":"anodized","recolorable":false,"color":"placeholder-black","note":"\"Carbine Receiver Extension\" (Aero's page); finish not stated beyond the photo's black. Black on the FDE Cerakote lower too, with its castle nut and end plate (Aero's photo of APAR600102)."}},"components":{"receiver":{"label":"Receiver","material":"receiver"},"grip":{"label":"A2 grip","material":"grip"},"stock":{"label":"M4 stock","material":"stock"},"tube":{"label":"Receiver extension","material":"tube"},"selector":{"label":"Selector","material":"controls"}},"geometry":{"components":{"receiver":"aero-m4e1-lower.receiver.glb","grip":"aero-m4e1-lower.grip.glb","stock":"aero-m4e1-lower.stock.glb","selector":"aero-m4e1-lower.selector.glb"},"approximations":["Its fire controls (the pins, their ends in the receiver's holes, and their heads; the selector on SAFE, the bolt catch, the magazine release) drawn as the Rise kit's, a mil-spec kit whose figures are the Army drawings', on the body's left face at the TDP's width; Aero publishes its own kit's no more than \"a mil-spec lower parts kit\". Where Aero's forging stands out further than the TDP's (its bosses, its fence's panel, its pivot lug's ears), the kit's catch, button and pivot pin sit inside it. The pivot pin's head is drawn on the right ear's own outer face (Brownells' photo of the complete lower from below has it there, beside the shelf the detent's hole is in), its flat to the rear, and the pin from one ear's face to the other's (a real pin's plain end stands a little out of the left ear, which isn't drawn). The trigger is the Army drawing's (8448592, its side elevation traced, .290 across), turned 1° back about its pin to where its blade sits on Aero's photo; its blade's rounded section, the disconnector, the hammer and the springs aren't drawn.","Receiver as a visual hull: its traced side outline across the rear view's section behind the magwell (and, from the takedown pin to the panels, the TDP's body: the stripped receiver's bottom view shows one width there) and the front view's ahead of it (the flare), the integral guard's window cut through. The end views were scaled by the side's height alone; the tower ring reads 1.35 against the standard's 1.39.","The receiver's rear end (2026-10-05): behind the takedown pin, below where the ring's flanks come down to it (the rear view's waist, 0.03 to 0.04 in under the pin line, where that view is 0.855 across), the hull is held to the TDP's body too. The rear view's outline below there is the bolt catch's bosses, the catch's pad and the right panel, which stand 3 to 4.5 in further forward: the hull had carried them back to the rear face as a collar 1.28 in across under the ring, with the bottom view's taper under it as far as the pin. Aero's rear photo has the near end 0.84 in across there (112 px at 133.4 px/in; from close, so large if anything). The webs from the ring down to the deck by the pin keep the bottom view's taper, as wide below the deck as the rear view's flanks allow (0.42 to 0.51 from the centre): what they are below the deck no view on file shows.","The inside a mil-spec lower has, from the Army's drawing 8448608 (D46), as the Workhorse's: the fire-control pocket, the rear lug's slot, the safety detent's boss, the trigger slot and the magazine well with its spine slot. The well's walls are as thick as the hull leaves them (the front view's flare at each height), thicker than a real well's near the top.","The tower's ring is bored through for the receiver extension (2026-10-05; it was a solid plug) at the mil-spec extension's OD, 1.148 in, the tube the app draws: the thread it is cut with isn't on file. The bore runs on forward as the trough between the ring's webs until it runs out above the deck. The webs rise to the ring's front face along the Army drawing's arc (.750 R, 8448608 sheet 1: 2026-10-12) and no higher: the outline has them up to 0.12 in above it. Its deck, from just behind the takedown pin to where its top turns down at the pivot lug, is the Army drawing's plane (.250 -.003 above the pins: std.ar15.deck_y), not the outline's own top edge, which reads a hundredth off it and not level (2026-10-12): the deck is the seat every upper sits on. The receiver extension itself is drawn from the receiver's rear face back, so with the upper off the bore shows empty as far as that face, where a real extension's front end stands just short of the ring's front face.","The pivot lug is two ears (2026-10-05; it was a solid block, and an upper's front lug stood in it) with the slot the upper's lug goes in between them, the Army drawing's .500 (Section C-C), cut from the well's front face forward and from the ears' undersides up, as Aero's front photo shows it; the well's front wall is left whole between the ears (how far down the slot is cut into it isn't on file). Each ear is cut to its own outer face (2026-10-05; the hull had carried the well's faces forward over them, 0.35 in thick on the left and 0.41 on the right): 0.519 in from the slot's middle on the right and 0.542 on the left, 1.06 across, so 0.27 and 0.29 thick, read on Aero's front photos of two specimens at the scale of the slot between them. The right ear begins at the right panel's front end, 0.19 in behind the pin: a square step, the shelf the pivot detent's hole is in on the photo, drawn square down to the lug's underside (its lower outer corner is sloped away on the photo) and without the hole. The left ear begins at the foot of a short ramp down from the left side's face, drawn upright where the photo has it leaning back as it goes down; below the pin line the ear's face runs on into the well's front corner, which is square here.","Ahead of the body (2026-10-03), Aero's own forging at the faces its two bottom views (two specimens, each scaled by the TDP's body) and its front view give: the right panel 0.667 from the centre down to Y -1.03 and the wall 0.56 below it, the left face 0.603, the pad round the catch's slot 0.667 (its rear end hidden: drawn round as its front), the bolt catch's bosses 0.707; each panel's ramp up from the body where the side photos show it. The front view is put to its own horizontal standard, the front lug's slot (.500), and gives the well's front and its mouth's flare; the end views' hull had spread the pad and the bosses along the whole well. The floor of the recess round the button's pocket isn't sourced: the pocket alone is cut.","The raised block round the magazine catch on the right side ends 3.64 in ahead of the takedown pin in a chamfer, and the well's wall runs on from there to the pivot lug (2026-10-12: read on two photos of the stripped receiver's right side, recorded under aero-m4e1-stripped-lower; until then the hull carried the block's face on to the lug).","The catch's pocket in the right panel and its slot through the pad on the left, the bolt catch's slot below its bosses: the Army drawing's places and the reference model's depths, as the Workhorse's. The kit's button sits in the pocket at the drawing's fence (0.118 in below Aero's panel); where a mil-spec bolt catch's paddle stands against Aero's bosses, 0.09 out past the drawing's, isn't sourced.","The A2 grip from the complete lower's silhouette and the Army drawing's view along its axis (TDP 9349127 rev J, the bottom view: 1.270 over the knurl), swept along its 28.3° rake. That view's outline is the knurl's teeth where the checkered panels are: bridged (2026-10-05: each notch between two teeth had run the length of the grip as a groove, three of them showing from the side), with its checkered panels as plain pads standing out of the body by the teeth's depth on that view (0.030 in), as the CMMG kit's A2 grip is built from the same drawing. The panel's outline is the one picked on the drawing's side view for that kit's grip (the same scan; the side view isn't traced under this part), laid from this grip's heel at the size its depth square to the axis has against that view's (0.991): a registration of the side view on Aero's photo would put the panel's far end about 0.06 in nearer the heel. Its top block is as wide as that hull leaves it (1.05 to 1.25 in, where the drawing's top view says .885 over a height not on file yet); the checkering itself, its core and screw hole aren't drawn.","The M4 stock from the complete lower's silhouette, where Aero's photo has it (about one position step out), across the section and plan of the Army's design patent for an M4-pattern stock (US D620,067 S): the butt's teardrop from its rear elevation, the body 1.443 in wide flaring to the butt's 1.707 over its last 0.53 in from its top plan, scaled by the receiver extension in the same figure. Aero's stock is that pattern with slots in its sides where the patent's has pockets: its two rows of five slots are cut where its photo has them, to the reference model's USGI depth (Aero's own isn't sourced). Its adjustment lever (its outline on the photo, the patent's 0.757 across), the lever's lock pin's end and the sling loop at its toe (a 0.16 in wire bent to the patent's 1.785 by the model's 0.688, hanging as its silhouette does) are their own pieces, in the stock's finish; they had been traced into the stock's outline at its full width. The receiver extension is a plain cylinder at the standard's OD; the castle nut and end plate aren't drawn."],"controls":"rise-lpk","ledger":["aero-m4e1-lower.ear_right_out","aero-m4e1-lower.ear_left_out","aero-m4e1-lower.buffer_axis_above_pin","aero-m4e1-lower.butt_behind_pin","aero-m4e1-lower.grip_seat_y","aero-m4e1-lower.grip_width","aero-m4e1-lower.height","aero-m4e1-lower.magazine_seat_x","aero-m4e1-lower.magazine_seat_y","aero-m4e1-lower.rear_face_x","aero-m4e1-lower.tower_top_above_pin","aero-m4e1-lower.trigger_face_x","aero-m4e1-lower.trigger_guard_front_x","aero-m4e1-lower.trigger_guard_rear_x","aero-m4e1-lower.trigger_guard_rear_y","aero-m4e1-lower.trigger_pin_x","aero-m4e1-lower.trigger_pin_y","aero-m4e1-lower.trigger_rest_angle","std.ar15.trigger_body_width","aero-m4e1-lower.width","std.receiver_extension.milspec_od","std.receiver_extension.front_face_x","std.ar15.front_lug_slot_width","std.ar15.fcg_pocket_front_x","std.ar15.fcg_pocket_depth","std.ar15.magwell_front_inner_x"]},"profiles":{"side":{"plane":"xy","origin":"the takedown pin centre (the rifle frame origin), +x toward the muzzle","offset":{},"points":[[-1.167,0.722],[-1.145,-0.296],[-1.116,-0.502],[-0.821,-0.528],[-0.611,-0.621],[-0.414,-0.802],[-0.285,-1.059],[-0.112,-1.08],[-0.129,-1.24],[-0.079,-1.291],[-0.075,-1.371],[0.991,-1.987],[1.143,-1.979],[1.167,-2.324],[2.268,-2.512],[6.147,-1.85],[6.16,-1.753],[6.06,-1.458],[6.079,-0.609],[6.197,-0.391],[6.509,-0.148],[6.552,0.004],[6.501,0.13],[6.413,0.202],[5.926,0.245],[0.072,0.244],[-0.062,0.269],[-0.306,0.388],[-0.52,0.662],[-0.586,0.889],[-0.61,1.545],[-0.984,1.567],[-1.14,1.521]],"features":{"guard_window":[[[1.492,-1.934],[1.493,-1.379],[1.553,-1.219],[1.641,-1.14],[1.759,-1.098],[3.096,-1.102],[3.214,-1.161],[3.285,-1.241],[3.335,-1.401],[3.334,-1.888],[3.249,-2.099],[3.144,-2.178],[2.319,-2.336],[1.748,-2.242],[1.567,-2.145]]]},"scaleRefs":["std.ar15.pin_spacing"],"inputs":{"std.ar15.pin_spacing":6.375},"tolerance":0.02,"photo":"references/aero-m4e1-lower 30b8c6d3edf1 (right side, Aero's studio photo of the stripped M4E1, pin-framed by its open holes)","method":"luminance < 215, largest piece, holes up to 4000 px filled; frame from the reviewed holes takedown (179.5,230.5) r=14px, pivot (937.5,228.5) r=8px (118.9 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.02 in with the extremes kept: 33 points (IoU 0.994 with the full outline); checks: −x_min 1.167 ± 0.013; x_max 6.552 ± 0.018; y_max 1.567 ± 0.013; −y_min 2.512 ± 0.014; height 4.079 ± 0.026; features through the same placement (guard_window: the integral trigger guard's window, flood-filled from a pixel inside it) (tools/trace.py)","via":"harvest","note":"Outer silhouette of the stripped receiver with its holes filled; the trigger guard is integral (the lowest point), the magwell flared."},"rear":{"plane":"zy","origin":"the tower ring's top on the receiver's centre plane; the part frame adds tower_top_above_pin","offset":{"y":"tower_top_above_pin"},"points":[[-0.682,-0.566],[-0.682,-0.754],[-0.42,-1.593],[-0.484,-1.672],[-0.574,-1.702],[-0.615,-1.751],[-0.607,-1.856],[-0.555,-1.923],[-0.532,-2.088],[-0.487,-2.156],[-0.547,-2.246],[-0.555,-2.336],[-0.472,-2.448],[-0.487,-2.531],[-0.555,-2.568],[-0.547,-2.621],[-0.487,-2.681],[-0.487,-3.625],[-0.54,-3.94],[-0.289,-3.982],[-0.206,-4.079],[0.266,-4.079],[0.349,-3.989],[0.645,-3.94],[0.645,-3.625],[0.555,-3.4],[0.555,-2.981],[0.562,-2.891],[0.667,-2.808],[0.667,-1.818],[0.562,-1.646],[0.454,-1.62],[0.435,-1.586],[0.66,-0.851],[0.682,-0.664],[0.63,-0.394],[0.424,-0.12],[0.289,0],[-0.004,0],[-0.296,0],[-0.487,-0.176],[-0.63,-0.379]],"scaleRefs":["aero-m4e1-lower.height"],"inputs":{"aero-m4e1-lower.height":4.079},"tolerance":0.02,"photo":"references/aero-m4e1-lower 748bb1292dc5 (rear view, Aero's studio photo of the stripped M4E1 (the tower ring above, the magwell below))","method":"distance from the border's background colour, largest piece, holes filled; scale from aero-m4e1-lower.height = 4.079 in (y-extent 544 px → 133.4 px/in); origin at x center, y max of the outline; Douglas-Peucker at 0.02 in with the extremes kept: 42 points (IoU 0.991 with the full outline); checks: median row width in y [-0.9, -0.5] (1.290–1.365) 1.351 ± 0.025 in vs std.ar15.buffer_tower_od 1.392 ± 0.01 (confirmed): DISAGREES; width 1.365 ± 0.025 (tools/trace.py)","via":"harvest","note":"The receiver seen from behind, scaled by the height the side trace measured. One scale reference: the ring's width against the standard's OD is the check."},"front":{"plane":"zy","origin":"the tower ring's top on the receiver's centre plane; the part frame adds tower_top_above_pin","offset":{"y":"tower_top_above_pin"},"points":[[-0.779,-1.208],[-0.764,-1.306],[-0.643,-1.464],[-0.651,-1.539],[-0.726,-1.622],[-0.726,-1.712],[-0.67,-1.731],[-0.636,-1.787],[-0.643,-1.885],[-0.726,-1.991],[-0.719,-2.051],[-0.643,-2.126],[-0.636,-2.871],[-0.704,-3.037],[-0.689,-3.759],[-0.346,-3.846],[-0.335,-4.008],[-0.248,-4.079],[0.294,-4.064],[0.365,-4],[0.376,-3.853],[0.692,-3.785],[0.734,-3.752],[0.756,-3.007],[0.651,-2.736],[0.643,-2.472],[0.722,-2.446],[0.764,-2.367],[0.756,-1.246],[0.779,-1.065],[0.764,-0.967],[0.711,-0.892],[0.726,-0.636],[0.674,-0.433],[0.546,-0.23],[0.301,0],[0,-0.008],[-0.331,-0.008],[-0.636,-0.335],[-0.741,-0.636],[-0.741,-0.824],[-0.704,-0.967]],"scaleRefs":["aero-m4e1-lower.height"],"inputs":{"aero-m4e1-lower.height":4.079},"tolerance":0.02,"photo":"references/aero-m4e1-lower 3fb9b60111c0 (front view, Aero's studio photo of the stripped M4E1 (the pivot lug above the magwell))","method":"distance from the border's background colour, largest piece, holes filled; scale from aero-m4e1-lower.height = 4.079 in (y-extent 542 px → 132.9 px/in); origin at x center, y max of the outline; Douglas-Peucker at 0.02 in with the extremes kept: 42 points (IoU 0.992 with the full outline); checks: median row width in y [-2.0, -1.3] (1.400–1.528) 1.443 ± 0.025 (tools/trace.py)","via":"harvest","note":"The receiver seen from the front (mirrored into the zy plane), scaled by the side's height; the body's width against the rear view's is its check."},"complete":{"plane":"xy","origin":"the takedown pin centre (the rifle frame origin), +x toward the muzzle","offset":{},"points":[[-8.594,1.033],[-8.546,0.733],[-8.548,0.401],[-8.515,0.302],[-8.532,0.186],[-8.484,-0.114],[-8.501,-0.213],[-8.468,-0.263],[-8.485,-0.363],[-8.453,-0.462],[-8.454,-0.794],[-8.421,-0.828],[-8.439,-0.994],[-8.39,-1.226],[-8.408,-1.425],[-8.375,-1.459],[-8.376,-1.774],[-8.343,-1.808],[-8.345,-2.123],[-8.312,-2.156],[-8.329,-2.256],[-8.28,-2.422],[-8.297,-2.472],[-8.233,-2.837],[-8.249,-2.887],[-8.216,-2.921],[-8.185,-3.253],[-8.077,-3.345],[-7.828,-3.346],[-7.787,-3.305],[-7.619,-3.057],[-7.669,-2.99],[-7.667,-2.641],[-7.36,-2.585],[-7.293,-2.602],[-6.549,-1.601],[-6.408,-1.461],[-5.809,-1.248],[-4.759,-0.573],[-3.365,-0.564],[-3.142,-0.789],[-3.102,-1.129],[-3.077,-1.022],[-3.027,-0.989],[-2.925,-0.641],[-2.683,-0.368],[-2.384,-0.237],[-1.72,-0.24],[-1.677,-0.083],[-1.684,0.291],[-1.625,0.282],[-1.601,0.174],[-1.253,0.173],[-1.248,-0.5],[-1.223,-0.525],[-1.123,-0.509],[-0.858,-0.543],[-0.609,-0.644],[-0.37,-0.886],[-0.28,-1.094],[-0.139,-1.103],[-0.296,-1.111],[-0.338,-1.152],[-0.323,-1.418],[-0.407,-1.7],[-2.181,-4.347],[-2.198,-4.446],[-1.974,-4.539],[-0.681,-4.861],[-0.349,-4.929],[-0.183,-4.93],[-0.008,-4.773],[-0.008,-4.707],[-0.123,-4.556],[-0.123,-4.44],[0.414,-3.414],[0.556,-3.29],[0.805,-3.308],[0.846,-3.267],[0.847,-3.2],[0.715,-3.05],[0.699,-2.901],[1.009,-2.329],[1.142,-2.314],[1.158,-2.347],[1.307,-2.381],[2.187,-2.535],[2.353,-2.536],[6.174,-1.875],[6.183,-1.767],[6.085,-1.518],[6.089,-0.671],[6.207,-0.422],[6.315,-0.315],[6.523,-0.192],[6.574,-0.092],[6.574,-0.009],[6.541,0.074],[6.401,0.182],[3.595,0.214],[3.562,0.28],[3.48,0.297],[3.372,0.373],[3.356,0.572],[3.249,0.664],[3.116,0.648],[3.024,0.54],[3.023,0.325],[3.081,0.216],[2.334,0.22],[2.342,0.278],[2.301,0.32],[1.689,0.688],[1.589,0.689],[1.481,0.598],[1.255,0.226],[-0.073,0.249],[-0.371,0.417],[-0.577,0.709],[-0.576,0.974],[-0.626,0.991],[-0.625,1.107],[-0.608,1.257],[-0.575,1.256],[-0.559,1.024],[-0.541,1.256],[-0.566,1.314],[-0.624,1.323],[-0.631,1.547],[-1.046,1.549],[-1.229,1.501],[-1.262,1.534],[-1.561,1.535],[-1.619,1.494],[-1.645,1.403],[-1.71,1.503],[-2.076,1.522],[-8.019,1.602],[-8.118,1.619],[-8.25,1.77],[-8.466,1.787],[-8.558,1.696],[-8.591,1.58]],"features":{"grip":[[[-2.256,-1.208],[1.064,-1.226],[1.044,-5.094],[-2.276,-5.077]]],"stock":[[[-8.715,1.847],[-1.576,1.809],[-1.603,-3.42],[-8.742,-3.383]]],"tube":[[[-1.693,1.611],[-0.631,1.605],[-0.639,0.111],[-1.701,0.117]]],"guard_window":[[[1.5,-2.042],[1.504,-1.361],[1.537,-1.278],[1.696,-1.138],[1.829,-1.122],[1.853,-1.147],[1.769,-1.445],[1.784,-1.694],[1.932,-2.011],[2.072,-2.152],[2.105,-2.153],[2.131,-2.095],[2.015,-1.911],[1.967,-1.629],[2.018,-1.43],[2.177,-1.207],[2.293,-1.124],[3.024,-1.111],[3.206,-1.195],[3.297,-1.304],[3.313,-1.37],[3.31,-1.985],[3.259,-2.117],[3.184,-2.191],[3.018,-2.257],[2.353,-2.37],[2.154,-2.369],[1.723,-2.283],[1.549,-2.158]]],"stock_lever":[[[-5.842,-1.273],[-4.726,-0.565],[-3.365,-0.572],[-3.15,-0.789],[-3.119,-1.121],[-3.816,-1.134],[-4.231,-1.132],[-4.497,-1.147],[-5.663,-1.921],[-5.845,-1.854]]],"stock_lock_pin":[[[-4.231,-1.132],[-3.816,-1.134],[-3.818,-1.516],[-4.233,-1.514]]],"sling_loop":[[[-7.659,-2.641],[-7.31,-2.593],[-6.832,-3.26],[-6.916,-3.475],[-7.198,-3.474],[-7.661,-2.99]]]},"scaleRefs":["std.ar15.pin_spacing"],"inputs":{"std.ar15.pin_spacing":6.375},"tolerance":0.02,"photo":"references/aero-m4e1-lower 4a14a1778a59 (right side, Aero's studio photo of the complete lower APAR600101, pin-framed by its pin heads)","method":"luminance < 215, 2 polygons excluded, largest piece, holes up to 4000 px filled; frame from the reviewed holes takedown (560.5,218.5) r=14px, pivot (944.5,216.5) r=10px (60.2 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.02 in with the extremes kept: 143 points (IoU 0.994 with the full outline); checks: −x_min 8.594 ± 0.042 in vs aero-m4e1-lower.butt_behind_pin 8.601 ± 0.054 (corroborated): agrees; x_max 6.574 ± 0.036 in vs aero-m4e1-lower.front_ahead_of_pin 6.547 ± 0.022 (conflict): agrees; y_max 1.787 ± 0.026; features through the same placement (grip: the A2 grip, below the receiver's underside; stock: the M4 stock, from the butt to its front face at the exposed tube; tube: the exposed receiver extension with its castle nut, between the stock's front and the receiver's rear face; guard_window: the integral trigger guard's window, with the trigger's blade in it; stock_lever: the M4 stock's adjustment lever, its top edge along the stock's underside; stock_lock_pin: the lever's lock pin, its end hanging below the lever; sling_loop: the sling loop below the toe, seen edge-on: from the toe's slot (its upper end) forward and down) (tools/trace.py)","via":"harvest","note":"The whole product's silhouette as sold, with the stock where Aero's photo has it (about 0.63 in of tube shows between the castle nut and the stock: one position step out). The receiver is drawn from its own stripped-receiver profiles; this outline gives the grip, the stock and the tube."},"stock_end":{"plane":"zy","origin":"the stock's top, centred: offset up to where the stock's top stands above the pin line","offset":{"y":"stock_top_above_pin"},"points":[[-0.858,-1.778],[-0.858,-2.135],[-0.844,-2.162],[-0.858,-2.186],[-0.844,-2.199],[-0.82,-2.788],[-0.807,-2.802],[-0.742,-3.381],[-0.728,-3.395],[-0.723,-3.497],[-0.709,-3.511],[-0.649,-3.896],[-0.515,-4.392],[-0.54,-4.417],[-0.61,-4.417],[-0.612,-4.429],[-0.521,-4.431],[-0.496,-4.457],[-0.468,-4.559],[-0.494,-4.584],[-0.61,-4.584],[-0.612,-4.624],[-0.47,-4.621],[-0.436,-4.656],[-0.408,-4.73],[-0.433,-4.774],[-0.596,-4.774],[-0.61,-4.76],[-0.612,-4.772],[-0.41,-4.779],[-0.38,-4.809],[-0.38,-4.837],[-0.348,-4.888],[-0.373,-4.927],[-0.582,-4.927],[-0.612,-4.962],[-0.331,-4.964],[-0.202,-5.099],[-0.123,-5.136],[0.039,-5.154],[0.053,-5.141],[0.155,-5.136],[0.234,-5.099],[0.364,-4.964],[0.612,-4.962],[0.61,-4.913],[0.572,-4.951],[0.545,-4.951],[0.521,-4.927],[0.406,-4.927],[0.38,-4.897],[0.413,-4.814],[0.447,-4.774],[0.612,-4.772],[0.61,-4.76],[0.466,-4.76],[0.44,-4.721],[0.498,-4.621],[0.612,-4.619],[0.521,-4.584],[0.496,-4.545],[0.528,-4.448],[0.559,-4.417],[0.612,-4.415],[0.547,-4.378],[0.552,-4.346],[0.644,-4.026],[0.705,-3.66],[0.718,-3.646],[0.723,-3.548],[0.737,-3.534],[0.742,-3.419],[0.765,-3.358],[0.783,-3.108],[0.802,-3.062],[0.802,-2.974],[0.816,-2.96],[0.839,-2.45],[0.853,-2.436],[0.858,-1.805],[0.853,-1.68],[0.839,-1.666],[0.834,-1.37],[0.82,-1.356],[0.816,-1.18],[0.802,-1.166],[0.765,-0.818],[0.742,-0.753],[0.718,-0.559],[0.644,-0.387],[0.644,-0.067],[0.6,-0.079],[0.406,-0.074],[0.392,-0.088],[0.336,-0.074],[0.313,-0.097],[0.192,-0.07],[0.162,-0.039],[0.176,-0.021],[0.169,0],[0.002,0],[-0.058,0],[-0.056,-0.035],[-0.086,-0.065],[-0.262,-0.074],[-0.392,-0.13],[-0.484,-0.19],[-0.591,-0.297],[-0.626,-0.243],[-0.617,-0.1],[-0.654,-0.067],[-0.654,-0.392],[-0.723,-0.535],[-0.779,-0.874],[-0.797,-1.092],[-0.82,-1.161],[-0.844,-1.764]],"scaleRefs":["aero-m4e1-lower.stock_height","aero-m4e1-lower.stock_butt_width"],"inputs":{"aero-m4e1-lower.stock_butt_width":1.707,"aero-m4e1-lower.stock_height":5.179},"tolerance":0.01,"photo":"references/aero-m4e1-lower 2a667d81ad90 (US D620,067 S (the Army's M4-pattern buttstock), FIG. 6 rear elevation, 300 dpi)","method":"luminance < 128, inside [688, 570, 1810, 1025], 4 boxes excluded, closing ×3, largest piece, holes filled, inset 2 px (half the outline's stroke); rotated -90.0° as declared; scale from aero-m4e1-lower.stock_height = 5.179 in (y-extent 1112 px → 214.7 px/in) and aero-m4e1-lower.stock_butt_width = 1.707 in (x-extent 370 px → 216.8 px/in), which agree within 1.0%; mean 215.7 px/in; origin at x center, y max of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 117 points (IoU 0.996 with the full outline) (tools/trace.py)","via":"harvest","note":"Seen from behind; symmetric about the tube's plane. The keyhole round the tube's end, the screw and the checkering are inside the outline."},"grip_section":{"plane":"xz","origin":"the backstrap's end (x' = 0), centred across. A plan in the grip's own frame: x' square to its axis toward the front strap (grip_rake below the bore line), z across","offset":{},"points":[[0,-0.022],[0.036,-0.207],[0.111,-0.334],[0.297,-0.495],[0.451,-0.544],[0.452,-0.569],[0.604,-0.585],[0.643,-0.629],[0.856,-0.627],[0.886,-0.598],[0.995,-0.634],[1.2,-0.617],[1.24,-0.569],[1.261,-0.6],[1.322,-0.557],[1.37,-0.577],[1.457,-0.528],[1.956,-0.406],[2.146,-0.225],[2.155,-0.003],[2.138,0.223],[2.044,0.279],[1.949,0.403],[1.287,0.573],[1.272,0.604],[1.211,0.617],[1.212,0.584],[0.899,0.603],[0.873,0.634],[0.622,0.609],[0.559,0.565],[0.476,0.577],[0.43,0.539],[0.306,0.521],[0.078,0.28],[0.015,0.125]],"scaleRefs":["aero-m4e1-lower.grip_depth","aero-m4e1-lower.grip_width"],"inputs":{"aero-m4e1-lower.grip_depth":2.153,"aero-m4e1-lower.grip_width":1.27},"tolerance":0.02,"photo":"references/aero-m4e1-lower be585e351439 (US Army TDP drawing 9349127 (Grip, Pistol) rev J, frame 1 of 2 (the user's M16 TDP scan, PDF page 33): the bottom view, along the grip's axis)","method":"luminance < 128, inside [2290, 3640, 2960, 4160], pieces ≥ 300 px, closing ×1, largest piece, holes filled, inset 3 px (half the outline's stroke); rotated +29.1° as declared; scale from aero-m4e1-lower.grip_depth = 2.153 in (x-extent 587 px → 272.5 px/in) and aero-m4e1-lower.grip_width = 1.27 in (y-extent 345 px → 272.0 px/in), which agree within 0.2%; mean 272.2 px/in; origin at x min, y center of the outline; Douglas-Peucker at 0.02 in with the extremes kept: 36 points (IoU 0.987 with the full outline) (tools/trace.py)","via":"user","note":"The grip seen from below along its axis: the silhouette of every section square to the axis at once (the widest is the knurl's, 1.270), not one section; symmetric about its long axis, so z's sign is immaterial. The nested outlines inside it (the bottom's flat, the screw hole, the maker's mark) aren't the outline."},"grip_front":{"plane":"zy","origin":"the top face (y = 0, offset to grip_top_y, its height at the pin's X), centred on the block. Square to the top face: swept along it, the part frame turned grip_top_slope nose-up about (0, grip_top_y)","offset":{"y":"grip_top_y"},"points":[[-0.686,-2.596],[-0.667,-3.36],[-0.61,-3.641],[-0.545,-3.747],[-0.391,-3.874],[-0.065,-3.878],[-0.038,-3.897],[0.327,-3.886],[0.429,-3.817],[0.515,-3.717],[0.553,-3.625],[0.594,-3.39],[0.621,-2.813],[0.594,-1.711],[0.53,-0.929],[0.439,-0.431],[0.446,-0.063],[0.41,-0.011],[0.315,0],[0,0],[-0.431,-0.017],[-0.446,-0.412],[-0.53,-0.792],[-0.617,-1.381],[-0.67,-2.038]],"scaleRefs":["aero-m4e1-lower.grip_body_width"],"inputs":{"aero-m4e1-lower.grip_body_width":0.885},"tolerance":0.015,"photo":"references/aero-m4e1-lower be585e351439 (US Army TDP drawing 9349127 (Grip, Pistol) rev J, frame 1 of 2 (the user's M16 TDP scan, PDF page 33): the front view, along the top face)","method":"luminance < 128, inside [4625, 2398, 5030, 3440], 6 boxes excluded, pieces ≥ 300 px, closing ×1, largest piece, holes filled, inset 3 px (half the outline's stroke); scale from aero-m4e1-lower.grip_body_width = 0.885 in (median width over 0.03–0.09 of the height from the top, 232–235 px 233 px → 263.3 px/in); origin at x center, y max of the outline (x over 0.03–0.09 of the height from the top); Douglas-Peucker at 0.015 in with the extremes kept: 25 points (IoU 0.992 with the full outline); checks: height 3.897 ± 0.067 in vs aero-m4e1-lower.grip_height 3.709 ± 0.06 (provisional): DISAGREES; width 1.307 ± 0.025 in vs aero-m4e1-lower.grip_width 1.27 ± 0.02 (confirmed): agrees; median row width in y [-0.33, -0.05] (0.878–0.892) 0.885 ± 0.019 (tools/trace.py)","via":"user","note":"The grip seen from the front along its top face: the block .885 wide below the face, the body flaring out under it, the bottom's corners rounded. Its body is wider than the grip's (1.31 against 1.270) and its height 5% more than grip_height: it is drawn narrow and scaled by the block; a prism of it limits the top, the section the body."},"bottom":{"plane":"xz","origin":"the rearmost point (the receiver's rear face, from below), centred on the ring; the part frame adds rear_face_x. x forward, z to the right","offset":{"x":"rear_face_x"},"points":[[0,0.28],[0,0],[0,-0.298],[0.047,-0.587],[0.089,-0.648],[0.191,-0.675],[0.48,-0.675],[0.629,-0.648],[0.871,-0.536],[1.011,-0.517],[1.141,-0.433],[3.992,-0.461],[3.997,0.41],[1.132,0.424],[1.002,0.508],[0.862,0.526],[0.629,0.638],[0.219,0.675],[0.098,0.648],[0.056,0.587]],"scaleRefs":["aero-m4e1-lower.tower_od"],"inputs":{"aero-m4e1-lower.tower_od":1.351},"tolerance":0.02,"photo":"references/aero-m4e1-lower ab9b1c2f8e07 (bottom view, Aero's studio photo of the stripped M4E1 in FDE Cerakote (APAR600002C), from the tower to the magazine well's panels)","method":"distance from the border's background colour, inside [0, 0, 1000, 469], largest piece, holes filled; rotated +90.0° as declared; scale from aero-m4e1-lower.tower_od = 1.351 in (y-extent 145 px → 107.3 px/in); origin at x min, y center of the outline; Douglas-Peucker at 0.02 in with the extremes kept: 20 points (IoU 0.988 with the full outline); checks: height in x [1.3, 3.95] 0.894 ± 0.034 in vs std.ar15.lower_body_width 0.88 ± 0.008 (confirmed): agrees; height in x [0.6, 0.8] 1.295 ± 0.040; height in x [0.85, 1.0] 1.081 ± 0.037; height in x [1.0, 1.15] 1.025 ± 0.036; y_max in x [1.3, 3.95] 0.433 ± 0.017; −y_min in x [1.3, 3.95] 0.461 ± 0.017; x_max 3.997 ± 0.090 (tools/trace.py)","via":"harvest","note":"The stripped receiver seen from below, as far forward as where it widens into the magazine well's panels (the front edge is the box's, not the part's): the ring at the rear, tapering over about half an inch to the body by the takedown pin's x, then one width to the panels. Its widest at each place along it, at whatever height: nothing on either side stands out between the takedown pin and the panels."},"trigger":{"plane":"xy","origin":"the pivot hole's centre (the trigger pin's axis), +x toward the muzzle","offset":{},"points":[[-1.204,-0.232],[-1.187,-0.265],[-0.105,-0.271],[-0.09,-0.286],[-0.09,-0.371],[-0.052,-0.403],[-0.046,-0.457],[-0.09,-0.552],[-0.125,-0.701],[-0.113,-0.98],[-0.078,-1.095],[0.005,-1.247],[0.005,-1.272],[0.152,-1.423],[0.203,-1.433],[0.224,-1.415],[0.224,-1.377],[0.125,-1.237],[0.068,-1.053],[0.062,-0.946],[0.078,-0.831],[0.095,-0.807],[0.125,-0.809],[0.125,-0.781],[0.1,-0.761],[0.103,-0.736],[0.186,-0.593],[0.247,-0.528],[0.378,-0.427],[0.493,-0.381],[0.493,-0.181],[0.514,-0.132],[0.769,-0.133],[0.788,0.044],[0.292,0.049],[0.263,0.011],[0.2,0.005],[0.163,0.025],[0.098,0.135],[-0.016,0.163],[-0.108,0.132],[-0.144,0.092],[-0.163,0.038],[-0.197,0.008],[-0.225,0.005],[-0.263,0.008],[-0.298,0.049],[-0.333,0.056],[-1.12,0.059],[-1.19,0.046],[-1.201,0.038]],"scaleRefs":["std.ar15.trigger_tail_behind_pivot"],"inputs":{"std.ar15.trigger_tail_behind_pivot":1.2025},"tolerance":0.01,"photo":"references/aero-m4e1-lower 1dabf089edf8 (US Army TDP drawing 8448592 (Trigger) rev L (the user's M16 TDP scan, PDF page 43): the side elevation)","method":"luminance < 128, inside [2650, 2815, 3330, 3345], 4 boxes excluded, closing ×2, the piece at [3051, 3000], holes filled, opening after the fill 9 px ×1, inset 2 px (half the outline's stroke); frame from the reviewed holes pivot, tail (315.2 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.01 in with the extremes kept: 51 points (IoU 0.985 with the full outline); checks: −y_min 1.433 ± 0.007 in vs std.ar15.trigger_blade_below_pivot 1.45 ± 0.02 (confirmed): agrees; −x_min 1.204 ± 0.007 in vs std.ar15.trigger_tail_behind_pivot 1.2025 ± 0.0075 (confirmed): agrees (tools/trace.py)","via":"user","note":"The trigger's side: its tail, the body with the disconnector's slot, the blade's front and back curves to its lowest point."}},"gaps":[{"what":"the receiver's widths: the flared magwell and the integral trigger guard","need":"an end view or a maker's figure; the body at the pins is drawn at the TDP's width"},{"what":"the stock's position in Aero's photo (it reads partly extended)","need":"a photo with the stock collapsed, or the exposed tube's position holes legible"}]},"aero-m4e1-stripped-lower":{"id":"aero-m4e1-stripped-lower","name":"M4E1 Stripped Lower Receiver","manufacturer":"Aero Precision","sku":"APAR600001C","url":"https://www.aeroprecisionusa.com/m4e1-stripped-lower-receiver-anodized-black","category":"lower","description":"Aero's enhanced forging, bare: \"The M4E1 Lower Receiver delivers billet aesthetics in a forged package. This custom-designed enhanced forging is machined from 7075-T6 Aluminum and compatible with all mil-spec AR15 parts.\" Its trigger guard is part of the forging (\"Integrated Trigger Guard\"), its magazine well's mouth is flared, and it is \"Marked and milled to accept short-throw safety selectors, but will work with standard selectors as well\". It comes with two small pieces that aren't drawn: \"Includes: Stripped M4E1 Lower Receiver / Nylon tipped tensioning set screw / Threaded Bolt Catch Pin\" (the \"Upper Tension Screw ... inserted in the grip tang\", and the pin the bolt catch turns on). Marked \"Cal Multi\", serial numbers \"M4-\" (Aero's page).","weight":"aero-m4e1-stripped-lower.weight","occupies":["trigger_guard"],"integral":["trigger_guard"],"brings":[],"seats":{},"requires":[],"anchors":{"pins":{"origin":[0,0,0],"note":"The rifle frame origin."},"buffer_tube_mount":{"origin":[0,"{.buffer_axis_above_pin}",0],"x":[-1,0,0]},"magwell":{"origin":["{.magazine_seat_x}","{std.ar15.mag_catch_slot_bottom_y} + {std.ar15.mag_catch_slot_h}",0],"note":"Where a seated magazine hangs: x where its spine's rear face sits in the well (magazine_seat_x), y at the catch's upper face, which is the top of the slot the catch comes through (the Army's drawing). A magazine's own anchor is the upper edge of its catch notch, so each hangs by its own. A standard well and catch (Aero: \"Works with standard AR15 components and magazines\"): no photo of a magazine seated in an M4E1 is on file."},"grip_lug":{"origin":[0,"{.grip_seat_y}",0],"note":"The grip mount's datum: the face either side of the lug that a grip's flat top bears on, at the takedown pin's x: the Army drawing's, 1.318 below the deck (this receiver's side outline has the level stretch behind the lug on it within a pixel and a half: grip_mating_y)."},"trigger_guard":{"origin":["{.trigger_guard_front_x}","{.trigger_guard_front_y}",0],"x":["{.trigger_guard_front_x} - {.trigger_guard_rear_x}","{.trigger_guard_front_y} - {.trigger_guard_rear_y}",0],"note":"Where a mil-spec lower's guard pins (the Army drawing's two ear holes). This receiver has neither ear nor hole there: its guard is part of the forging and the slot is occupied, so nothing mates here; the anchor frames the slot as the category asks of a lower with an integral guard."},"fcg":{"origin":["{.trigger_pin_x}","{.trigger_pin_y}",0],"note":"Trigger pin axis."},"lpk":{"origin":[0,0,"-{std.ar15.lower_body_width} / 2"],"note":"The body's left face (the TDP's width), level with the takedown pin: the controls' heads seat on it. Ahead of the body Aero's forging stands out further than the TDP's (its bosses, its catch pad, its pivot lug's ears): a kit's bolt catch, magazine catch and pivot pin, drawn at the drawing's faces, sit inside it there."},"selector":{"origin":["{std.ar15.selector_x}","{std.ar15.selector_y}",0],"note":"The selector's hole (the Army's drawing 8448608), on its axis at the receiver's mid-plane: a selector chosen on its own turns here (D86), its levers' inner faces on the body's two sides. Aero, of the M4E1: \"Marked and milled to accept short-throw safety selectors, but will work with standard selectors as well.\" (its page; the marks are pictograms either side of the hole, on both sides of the receiver, and aren't drawn)."}},"interfaces":{"receiver_pins":{"type":"ar15.upper_lower","role":"lower","anchor":"pins","params":{"pin_spacing":"={std.ar15.pin_spacing}"},"flips":false},"buffer_tube_mount":{"type":"ar15.buffer_tube_mount","role":"receiver","anchor":"buffer_tube_mount","params":{},"flips":false},"magwell":{"type":"ar15.magwell","role":"receiver","anchor":"magwell","params":{"family":"5.56"},"flips":false,"note":"A standard AR-15 magazine well: \"compatible with all mil-spec AR15 parts\", \"Compatibility Works with standard AR15 components and magazines\" (Aero's page); its \"Increased Magwell Flare\" is the mouth."},"grip_lug":{"type":"ar15.grip_lug","role":"receiver","anchor":"grip_lug","params":{},"flips":false},"trigger_guard":{"type":"ar15.trigger_guard","role":"receiver","anchor":"trigger_guard","params":{},"flips":false},"fcg":{"type":"ar15.fcg","role":"receiver","anchor":"fcg","params":{"pin_diameter":"small-pin"},"flips":false,"note":"No page states the pins' size in a figure: \"compatible with all mil-spec AR15 parts\" (Aero's page), whose drawing (8448608) has the hammer's and trigger's holes for .154 pins, and Aero's own complete lower on this receiver is sold with a \"Mil-spec Lower Parts Kit\"."},"lpk":{"type":"ar15.lpk","role":"receiver","anchor":"lpk","params":{},"flips":false},"selector":{"type":"ar15.selector","role":"receiver","anchor":"selector","params":{},"flips":false}},"materials":{"receiver":{"label":"Receiver","finish":"anodized","recolorable":true,"color":"placeholder-black","sheen":"matte","options":{"black":{"label":"Anodized Black","finish":"anodized","color":"placeholder-black","sheen":"matte","sku":"APAR600001C","source":"https://www.aeroprecisionusa.com/m4e1-stripped-lower-receiver-anodized-black"},"fde":{"label":"FDE Cerakote","finish":"cerakote","color":"aero-fde-cerakote","sku":"APAR600002C","source":"https://www.aeroprecisionusa.com/m4e1-stripped-lower-receiver-fde"},"odg":{"label":"OD Green Anodized","finish":"anodized","color":"aero-od-green-anodize-7075","sheen":"matte","sku":"APAR600501C","source":"https://www.aeroprecisionusa.com/m4e1-stripped-lower-receiver-od-green-anodized"},"odg_cerakote":{"label":"OD Green Cerakote","finish":"cerakote","color":"aero-od-green-cerakote","sku":"APAR600070C","source":"https://www.aeroprecisionusa.com/m4e1-stripped-lower-receiver-od-green-cerakote"},"kodiak":{"label":"Kodiak Brown Anodized","finish":"anodized","color":"aero-kodiak-brown-7075","sheen":"matte","sku":"APAR600025C","source":"https://www.aeroprecisionusa.com/m4e1-stripped-lower-receiver-kodiak-brown-anodized"},"sniper_grey":{"label":"Sniper Grey Cerakote","finish":"cerakote","color":"aero-sniper-grey-cerakote","sku":"APAR600072C","source":"https://www.aeroprecisionusa.com/m4e1-stripped-lower-receiver-sniper-grey-cerakote"}},"default":"black","note":"Aero's words for each finish, each its own page's Finish row and its own number (read on the harvested pages 2026-10-12): \"Anodized Black\", \"Magpul FDE Cerakote\", \"OD Green Anodized\", \"Magpul OD Cerakote\", \"Kodiak Brown Anodized\", \"Sniper Grey Cerakote\". A photo of each on THIS receiver is on file (its own gallery's right side view), and each is one colour all over: a stripped receiver is one piece. Also sold, and not offered here: Uncoated (APAR600001MC), bare aluminium as machined, \"NOTE: These parts are unfinished. Please ensure you apply a firearms appropriate finish such as Cerakote prior to assembly and use.\": no finish type draws bare metal as machined. The black is unmatched (sealed black anodize: its look is the finish type's). The two anodized colours are the presets matched on Aero's M4E1 upper, the same 7075 forging's dye, so an upper and a lower in one finish are one colour: this receiver's own photo (its right side, the flat behind its trigger pin) reads the green #707257, beside the upper's right view's #747f58 and darker than its left view's #7f8868, and the app draws it #7f8865 on the flat under the trigger pin (the preset is fitted to the mean of the upper's two views: 15 to 22 levels lighter than this photo); the brown reads #796a62 and is drawn #837065. The FDE is the preset fitted to three of Aero's photos, this receiver's among them (#af9883; drawn #a58c75). The OD Cerakote is the preset matched on Aero's handguard in that coat (this receiver's photo #615c54; drawn #585344, a little darker and yellower). Sniper Grey was matched on this receiver (#5a5c5b; drawn #595c5b). NOT this part, though the same forging: the M4E1 Low Profile (APAR600027C: no A on the well, FIRE and SAFE in words), the ambidextrous M4E1 PRO, the Freedom and Tacoma editions."}},"components":{"receiver":{"label":"Receiver","material":"receiver"}},"geometry":{"model":"aero-m4e1-stripped-lower.glb","components":{},"approximations":["Receiver as a visual hull, the complete lower's receiver cut for cut (pipeline/blender/aero_m4e1_receiver.py builds both; Aero's complete lower \"Includes: M4E1 Stripped Lower Receiver - Anodized Black\"): its traced side outline across the rear view's section behind the magazine well (and, from the takedown pin to the panels, the TDP's body, 0.880: the view from below shows one width there) and the front view's ahead of it (the flare), the integral guard's window cut through. The end views are scaled by the side's height alone; the tower's ring reads 1.35 across against the standard's 1.39 (Aero's has a flat on top and straight flanks). Behind the takedown pin, below where the ring's flanks come down to it, the hull is held to the TDP's body.","MORE METAL THAN ANY PUBLISHED WEIGHT: the model's closed volume as 7075 is 9.59 oz (5.878 cubic inches) against Aero's 8.35 and the sellers' 8.61 and 8.48. A hull of outlines: the magazine well's walls are as thick as the outside faces read on the photos leave them over the standard well (0.11 in on the right ahead of the catch's block, 0.13 to 0.15 on the left, where a mil-spec well's are a tenth, and the mouth's flare is carried up the lower half of both), the ring is bored at the receiver extension's size and not its thread's, and whatever lightening the forging has inside shows in no view on file. The weight the build counts is Aero's figure, never this.","What the receiver sold alone has cut that the complete lower's hasn't (it goes under parts chosen in their own slots): (1) its rear face is the Army drawing's (std.ar15.receiver_rear_x, -1.125), where an end plate bears: the outline's rearmost is the ring's near rim, 0.04 behind it, and its edge below the ring reads 0.015 behind. (2) The grip's mount is the standard's: the face a grip bears on 1.318 below the deck, and the lug the drawing's .375 across, its rear face under the takedown pin, its sloped face 1.228 from the pin at 60 degrees, its flat .93 below the seat, ending 2.300 ahead of the rear face where a grip's nose comes to (the Army's drawing 8448608). The side outline has the lug on the drawing's: its rear face 0.002 from it, its sloped face on its line within 0.004 in at both ends, its flat 0.017 above, the root's rear face 0.02 behind (each in the ledger); Aero's view from below has the lug narrow under the body with the seat's faces either side. (3) The rear underside, from the rear face's foot to the seat, is rounded across the body (a half-round, as the reference CAD model's forging has it) along the outline's own line, which runs 0.012 to 0.016 outside the reference model's arc: Aero's view from below has it in flat facets either side of a flat middle, which aren't read. (4) The integral trigger guard, its post and its bar, is 0.59 in across below the seat's level from its root to the magazine well, where the body is 0.880: the bar's flat between two creases in Aero's view from below, at the scale the magazine well seen through from below gives at that depth; its sides are drawn square, and it steps out to the well's faces where its window ends (the photos have a slanted face there). Its bar has its two round-ended slots through it, 0.335 in across, the rear one from 1.66 to 2.28 in ahead of the takedown pin and the front one from 2.43 to 3.26: each end read on the bar's own plane in that one view (good to about 0.04 in), cut straight up through the bar where the real ones may lean with it.","A grip that reaches on under the trigger guard's rear shares a sliver with this forging's guard: BCM's Grip Mod 3 runs to 1.52 in ahead of the takedown pin there (a filler for the gap behind a pinned guard), and the integral guard's root hangs 0.01 to 0.07 in lower behind the trigger than a mil-spec lower's ears (the outline: -2.32 falling to -2.38 where the drawing's ears end at -2.31), so the two models share 0.006 cubic inches. No page on file says how that grip goes on an integral guard: nothing is cut for it and no rule says anything. Magpul's MOE-K2+, which ends at the guard's root, shares nothing.","The inside a mil-spec lower has, from the Army's drawing 8448608 (D46): the fire-control pocket, the rear lug's slot, the safety detent's boss, the trigger slot and the magazine well with its spine slot (Aero: \"compatible with all mil-spec AR15 parts\"). The well's walls are as thick as the hull leaves them, thicker than a real well's near the top.","The tower's ring is bored through for the receiver extension at the mil-spec extension's OD, 1.148 in: the thread it is cut with isn't on file. The bore runs on forward as the trough between the ring's webs until it runs out above the deck. The webs rise to the ring's front face along the Army drawing's arc (.750 R, 8448608 sheet 1) and no higher: the outline has them up to 0.12 in above it. Its deck, from just behind the takedown pin to where its top turns down at the pivot lug, is the Army drawing's plane (.250 -.003 above the pins: std.ar15.deck_y), not the outline's own top edge, which reads a hundredth off it: the deck is the seat every upper sits on.","The pivot lug is two ears with the slot the upper's lug goes in between them, the Army drawing's .500 (Section C-C), cut from the well's front face forward; the well's front wall is left whole between the ears (how far down the slot is cut into it isn't on file). Each ear is cut to its own outer face, 0.519 in from the slot's middle on the right and 0.542 on the left (Aero's front photos of two specimens, at the scale of the slot between them). The right ear begins at a square step, the shelf the pivot detent's hole is in on the photo, drawn square and without the hole; the left ear at the foot of a short ramp, drawn upright.","Ahead of the body, Aero's own forging at the faces its two views from below and its front view give. On the right, the block round the magazine catch stands 0.664 from the centre, from its ramp up from the body (3.09 ahead of the takedown pin) to where its face ends in a chamfer (3.64, the chamfer down to the wall over 0.16 in: read on Aero's and Sportsman's right side photos), down to Y -1.03; ahead of the block and below it the well's wall is 0.56 from the centre, the face the large A is cut in, drawn straight up to the deck (the photos have a bevelled band along its top quarter inch, which isn't drawn) and down to the mouth's flare. THE COMPLETE LOWER'S RECEIVER DIFFERS HERE: it was built with the block's face carried on to the pivot lug, and still is (its script calls the same code without `catch_block`). The block's lower edge is square at its chamfer's foot (the photos have the chamfer from Y -0.80 to -1.03). On the left, the face 0.603 from the centre, the pad round the catch's slot 0.666 (its rear end hidden: drawn round as its front), the bolt catch's bosses 0.708; each ramp up from the body where the side photos show it. The catch's pocket in the block and its slot through the pad on the left, the bolt catch's slot below its bosses: the Army drawing's places and the reference model's depths.","A parts kit's controls are drawn by the kit, on the body's left face at the TDP's width: where Aero's forging stands out further than the TDP's (its bosses, its catch pad, its panel, its pivot lug's ears) the kit's bolt catch, magazine catch and pivot pin sit inside it. Where a mil-spec bolt catch's paddle stands against Aero's bosses isn't sourced.","Not drawn: the two pieces it ships with (the nylon tipped tensioning set screw in the lug's rear, whose end stands out of the lug in the side photos; the threaded bolt catch pin, whose head shows in the rear boss), the grip screw's hole in the lug and the safety detent's hole beside it in the seat, the buffer retainer's hole, the takedown detent's threaded hole, the pivot detent's hole, the bore's thread, the chamfers on the guard's inner edges, the selector's pictograms (two wedges by its hole on each side: the short throw's marks and the standard's), 'MOD M4E1 / CAL MULTI / M4-' and the maker's name on the left, the large A on the right of the well. Edges broken at 0.02 in."],"ledger":["aero-m4e1-stripped-lower.bolt_catch_boss_bottom_y","aero-m4e1-stripped-lower.bolt_catch_boss_front_x","aero-m4e1-stripped-lower.bolt_catch_boss_out","aero-m4e1-stripped-lower.bolt_catch_boss_rear_x","aero-m4e1-stripped-lower.buffer_axis_above_pin","aero-m4e1-stripped-lower.catch_block_front_ramp","aero-m4e1-stripped-lower.catch_block_front_x","aero-m4e1-stripped-lower.catch_pad_bottom_y","aero-m4e1-stripped-lower.catch_pad_front_x","aero-m4e1-stripped-lower.catch_pad_out","aero-m4e1-stripped-lower.catch_pad_rear_x","aero-m4e1-stripped-lower.catch_pad_top_y","aero-m4e1-stripped-lower.ear_left_out","aero-m4e1-stripped-lower.ear_left_ramp","aero-m4e1-stripped-lower.ear_left_rear_x","aero-m4e1-stripped-lower.ear_right_out","aero-m4e1-stripped-lower.ear_right_rear_x","aero-m4e1-stripped-lower.front_view_lug_slot","aero-m4e1-stripped-lower.grip_lug_face_angle","aero-m4e1-stripped-lower.grip_lug_flat_y","aero-m4e1-stripped-lower.grip_lug_rear_x","aero-m4e1-stripped-lower.grip_mating_y","aero-m4e1-stripped-lower.grip_seat_y","aero-m4e1-stripped-lower.guard_root_rear_x","aero-m4e1-stripped-lower.guard_slot1_front_x","aero-m4e1-stripped-lower.guard_slot1_rear_x","aero-m4e1-stripped-lower.guard_slot2_front_x","aero-m4e1-stripped-lower.guard_slot2_rear_x","aero-m4e1-stripped-lower.guard_slot_width","aero-m4e1-stripped-lower.guard_width","aero-m4e1-stripped-lower.panel_left_out","aero-m4e1-stripped-lower.panel_left_ramp","aero-m4e1-stripped-lower.panel_left_rear_x","aero-m4e1-stripped-lower.panel_right_bottom_y","aero-m4e1-stripped-lower.panel_right_out","aero-m4e1-stripped-lower.panel_right_ramp","aero-m4e1-stripped-lower.panel_right_rear_x","aero-m4e1-stripped-lower.rear_end_x","aero-m4e1-stripped-lower.rear_face_x","aero-m4e1-stripped-lower.rear_underside_arc_r","aero-m4e1-stripped-lower.tower_top_above_pin","aero-m4e1-stripped-lower.wall_right_below_panel","std.ar15.bolt_catch_plunger_hole_d","std.ar15.bolt_catch_plunger_hole_depth","std.ar15.bolt_catch_plunger_hole_y","std.ar15.bolt_catch_slot_bottom_y","std.ar15.bolt_catch_slot_floor","std.ar15.bolt_catch_slot_front_x","std.ar15.bolt_catch_slot_width","std.ar15.bore_axis_y","std.ar15.buffer_tower_front_x","std.ar15.deck_front_x","std.ar15.deck_y","std.ar15.fcg_pin_hole_d","std.ar15.fcg_pocket_corner_r","std.ar15.fcg_pocket_depth","std.ar15.fcg_pocket_front_x","std.ar15.fcg_pocket_length","std.ar15.fcg_pocket_width","std.ar15.front_lug_slot_width","std.ar15.grip_lug_face_angle","std.ar15.grip_lug_face_from_pin","std.ar15.grip_lug_width","std.ar15.grip_seat_below_deck","std.ar15.hammer_pin_x","std.ar15.hammer_pin_y","std.ar15.lower_body_width","std.ar15.mag_catch_cbore_d","std.ar15.mag_catch_cbore_depth","std.ar15.mag_catch_fence_out","std.ar15.mag_catch_hole_d","std.ar15.mag_catch_slot_bottom_y","std.ar15.mag_catch_slot_floor","std.ar15.mag_catch_slot_front_x","std.ar15.mag_catch_slot_h","std.ar15.mag_catch_slot_rear_x","std.ar15.mag_catch_x","std.ar15.mag_catch_y","std.ar15.mag_release_pocket_depth","std.ar15.mag_release_pocket_h","std.ar15.mag_release_pocket_w","std.ar15.magwell_box_length","std.ar15.magwell_corner_r","std.ar15.magwell_front_inner_x","std.ar15.magwell_length","std.ar15.magwell_spine_slot_width","std.ar15.magwell_width","std.ar15.pin_spacing","std.ar15.pivot_hole_d","std.ar15.rear_lug_slot_depth","std.ar15.rear_lug_slot_rear_x","std.ar15.rear_lug_slot_width","std.ar15.rear_underside_arc_center_below_seat","std.ar15.rear_underside_arc_center_x","std.ar15.rear_underside_arc_r_fullest","std.ar15.rear_underside_round_r","std.ar15.rear_wall_arc_r","std.ar15.receiver_rear_x","std.ar15.safety_detent_boss_below_deck","std.ar15.safety_detent_boss_face","std.ar15.safety_detent_boss_from_rear","std.ar15.safety_detent_boss_length","std.ar15.selector_hole_d","std.ar15.selector_x","std.ar15.selector_y","std.ar15.takedown_hole_d","std.ar15.trigger_pin_x","std.ar15.trigger_pin_y","std.ar15.trigger_slot_front_ahead_of_pin","std.ar15.trigger_slot_length","std.ar15.trigger_slot_width","std.ar15.upper_rear_face_x","std.receiver_extension.milspec_od"]},"profiles":{"side":{"plane":"xy","origin":"the takedown pin centre (the rifle frame origin), +x toward the muzzle","offset":{},"points":[[-1.167,0.722],[-1.145,-0.296],[-1.116,-0.502],[-0.821,-0.528],[-0.611,-0.621],[-0.414,-0.802],[-0.285,-1.059],[-0.112,-1.08],[-0.129,-1.24],[-0.079,-1.291],[-0.075,-1.371],[0.991,-1.987],[1.143,-1.979],[1.167,-2.324],[2.268,-2.512],[6.147,-1.85],[6.16,-1.753],[6.06,-1.458],[6.079,-0.609],[6.197,-0.391],[6.509,-0.148],[6.552,0.004],[6.501,0.13],[6.413,0.202],[5.926,0.245],[0.072,0.244],[-0.062,0.269],[-0.306,0.388],[-0.52,0.662],[-0.586,0.889],[-0.61,1.545],[-0.984,1.567],[-1.14,1.521]],"features":{"guard_window":[[[1.492,-1.934],[1.493,-1.379],[1.553,-1.219],[1.641,-1.14],[1.759,-1.098],[3.096,-1.102],[3.214,-1.161],[3.285,-1.241],[3.335,-1.401],[3.334,-1.888],[3.249,-2.099],[3.144,-2.178],[2.319,-2.336],[1.748,-2.242],[1.567,-2.145]]]},"scaleRefs":["std.ar15.pin_spacing"],"inputs":{"std.ar15.pin_spacing":6.375},"tolerance":0.02,"photo":"references/aero-m4e1-stripped-lower 30b8c6d3edf1 (right side, Aero's studio photo of the stripped M4E1, pin-framed by its open holes)","method":"luminance < 215, largest piece, holes up to 4000 px filled; frame from the reviewed holes takedown (179.5,230.5) r=14px, pivot (937.5,228.5) r=8px (118.9 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.02 in with the extremes kept: 33 points (IoU 0.994 with the full outline); checks: −x_min 1.167 ± 0.013 in vs aero-m4e1-stripped-lower.rear_behind_pin 1.155 ± 0.013 (corroborated): agrees; x_max 6.552 ± 0.018 in vs aero-m4e1-stripped-lower.front_ahead_of_pin 6.547 ± 0.022 (provisional): agrees; y_max 1.567 ± 0.013 in vs aero-m4e1-stripped-lower.tower_top_above_pin 1.554 ± 0.013 (corroborated): agrees; −y_min 2.512 ± 0.014 in vs aero-m4e1-stripped-lower.bottom_below_pin 2.508 ± 0.014 (corroborated): agrees; height 4.079 ± 0.026 in vs aero-m4e1-stripped-lower.height 4.079 ± 0.03 (provisional): agrees; y_max in x [0.6, 5.8] 0.250 ± 0.013 in vs std.ar15.deck_y 0.2485 ± 0.0015 (confirmed): agrees; features through the same placement (guard_window: the integral trigger guard's window, flood-filled from a pixel inside it) (tools/trace.py)","via":"harvest","note":"Outer silhouette of the stripped receiver with its holes filled; the trigger guard is integral (the lowest point), the magwell flared."},"rear":{"plane":"zy","origin":"the tower ring's top on the receiver's centre plane; the part frame adds tower_top_above_pin","offset":{"y":"tower_top_above_pin"},"points":[[-0.682,-0.566],[-0.682,-0.754],[-0.42,-1.593],[-0.484,-1.672],[-0.574,-1.702],[-0.615,-1.751],[-0.607,-1.856],[-0.555,-1.923],[-0.532,-2.088],[-0.487,-2.156],[-0.547,-2.246],[-0.555,-2.336],[-0.472,-2.448],[-0.487,-2.531],[-0.555,-2.568],[-0.547,-2.621],[-0.487,-2.681],[-0.487,-3.625],[-0.54,-3.94],[-0.289,-3.982],[-0.206,-4.079],[0.266,-4.079],[0.349,-3.989],[0.645,-3.94],[0.645,-3.625],[0.555,-3.4],[0.555,-2.981],[0.562,-2.891],[0.667,-2.808],[0.667,-1.818],[0.562,-1.646],[0.454,-1.62],[0.435,-1.586],[0.66,-0.851],[0.682,-0.664],[0.63,-0.394],[0.424,-0.12],[0.289,0],[-0.004,0],[-0.296,0],[-0.487,-0.176],[-0.63,-0.379]],"scaleRefs":["aero-m4e1-stripped-lower.height"],"inputs":{"aero-m4e1-stripped-lower.height":4.079},"tolerance":0.02,"photo":"references/aero-m4e1-stripped-lower 748bb1292dc5 (rear view, Aero's studio photo of the stripped M4E1 (the tower ring above, the magwell below))","method":"distance from the border's background colour, largest piece, holes filled; scale from aero-m4e1-stripped-lower.height = 4.079 in (y-extent 544 px → 133.4 px/in); origin at x center, y max of the outline; Douglas-Peucker at 0.02 in with the extremes kept: 42 points (IoU 0.991 with the full outline); checks: median row width in y [-0.9, -0.5] (1.290–1.365) 1.351 ± 0.025 in vs std.ar15.buffer_tower_od 1.392 ± 0.01 (confirmed): DISAGREES; median row width in y [-0.9, -0.5] (1.290–1.365) 1.351 ± 0.025 in vs aero-m4e1-stripped-lower.tower_od 1.351 ± 0.03 (provisional): agrees; median row width in y [-2.0, -1.3] (0.855–1.282) 1.040 ± 0.024 in vs aero-m4e1-stripped-lower.rear_body_width 1.04 ± 0.03 (provisional): agrees; width 1.365 ± 0.025 (tools/trace.py)","via":"harvest","note":"The receiver seen from behind, scaled by the height the side trace measured. One scale reference: the ring's width against the standard's OD is the check."},"front":{"plane":"zy","origin":"the tower ring's top on the receiver's centre plane; the part frame adds tower_top_above_pin","offset":{"y":"tower_top_above_pin"},"points":[[-0.779,-1.208],[-0.764,-1.306],[-0.643,-1.464],[-0.651,-1.539],[-0.726,-1.622],[-0.726,-1.712],[-0.67,-1.731],[-0.636,-1.787],[-0.643,-1.885],[-0.726,-1.991],[-0.719,-2.051],[-0.643,-2.126],[-0.636,-2.871],[-0.704,-3.037],[-0.689,-3.759],[-0.346,-3.846],[-0.335,-4.008],[-0.248,-4.079],[0.294,-4.064],[0.365,-4],[0.376,-3.853],[0.692,-3.785],[0.734,-3.752],[0.756,-3.007],[0.651,-2.736],[0.643,-2.472],[0.722,-2.446],[0.764,-2.367],[0.756,-1.246],[0.779,-1.065],[0.764,-0.967],[0.711,-0.892],[0.726,-0.636],[0.674,-0.433],[0.546,-0.23],[0.301,0],[0,-0.008],[-0.331,-0.008],[-0.636,-0.335],[-0.741,-0.636],[-0.741,-0.824],[-0.704,-0.967]],"scaleRefs":["aero-m4e1-stripped-lower.height"],"inputs":{"aero-m4e1-stripped-lower.height":4.079},"tolerance":0.02,"photo":"references/aero-m4e1-stripped-lower 3fb9b60111c0 (front view, Aero's studio photo of the stripped M4E1 (the pivot lug above the magwell))","method":"distance from the border's background colour, largest piece, holes filled; scale from aero-m4e1-stripped-lower.height = 4.079 in (y-extent 542 px → 132.9 px/in); origin at x center, y max of the outline; Douglas-Peucker at 0.02 in with the extremes kept: 42 points (IoU 0.992 with the full outline); checks: median row width in y [-2.0, -1.3] (1.400–1.528) 1.443 ± 0.025; width 1.558 ± 0.025 (tools/trace.py)","via":"harvest","note":"The receiver seen from the front (mirrored into the zy plane), scaled by the side's height; the body's width against the rear view's is its check."},"bottom":{"plane":"xz","origin":"the rearmost point (the receiver's rear face, from below), centred on the ring; the part frame adds rear_face_x. x forward, z to the right","offset":{"x":"rear_face_x"},"points":[[0,0.28],[0,0],[0,-0.298],[0.047,-0.587],[0.089,-0.648],[0.191,-0.675],[0.48,-0.675],[0.629,-0.648],[0.871,-0.536],[1.011,-0.517],[1.141,-0.433],[3.992,-0.461],[3.997,0.41],[1.132,0.424],[1.002,0.508],[0.862,0.526],[0.629,0.638],[0.219,0.675],[0.098,0.648],[0.056,0.587]],"scaleRefs":["aero-m4e1-stripped-lower.tower_od"],"inputs":{"aero-m4e1-stripped-lower.tower_od":1.351},"tolerance":0.02,"photo":"references/aero-m4e1-stripped-lower ab9b1c2f8e07 (bottom view, Aero's studio photo of the stripped M4E1 in FDE Cerakote (APAR600002C), from the tower to the magazine well's panels)","method":"distance from the border's background colour, inside [0, 0, 1000, 469], largest piece, holes filled; rotated +90.0° as declared; scale from aero-m4e1-stripped-lower.tower_od = 1.351 in (y-extent 145 px → 107.3 px/in); origin at x min, y center of the outline; Douglas-Peucker at 0.02 in with the extremes kept: 20 points (IoU 0.988 with the full outline); checks: height in x [1.3, 3.95] 0.894 ± 0.034 in vs std.ar15.lower_body_width 0.88 ± 0.008 (confirmed): agrees; height in x [0.6, 0.8] 1.295 ± 0.040; height in x [0.85, 1.0] 1.081 ± 0.037; height in x [1.0, 1.15] 1.025 ± 0.036; y_max in x [1.3, 3.95] 0.433 ± 0.017; −y_min in x [1.3, 3.95] 0.461 ± 0.017; x_max 3.997 ± 0.090 (tools/trace.py)","via":"harvest","note":"The stripped receiver seen from below, as far forward as where it widens into the magazine well's panels (the front edge is the box's, not the part's): the ring at the rear, tapering over about half an inch to the body by the takedown pin's x, then one width to the panels. Its widest at each place along it, at whatever height: nothing on either side stands out between the takedown pin and the panels."}},"gaps":[{"what":"its weight: Aero's table says 8.35 with no unit, sellers 8.61 oz and 8.48 oz; and the model's metal is more than any of them","need":"a page or a reviewer that weighs a stripped M4E1 lower; and for the metal, the well's walls and the forging's inside: a view down into the receiver, square, or a section"},{"what":"the integral guard: its width (0.59 ± 0.02) and its two slots' ends (± 0.04) are one reading each from the one view from below, which leans about 8 degrees along the receiver; its sides are drawn square and its slots cut straight up","need":"a square view from below of the whole receiver with both pin holes' ends in frame, or a view along it from the front at the guard's height"},{"what":"the rear underside's facets and the tang's shape behind the lug (drawn as a half-round across)","need":"a view from behind and below, square to the tang"},{"what":"the receiver extension's thread in the ring, and how far the pivot lug's slot runs down into the well's front wall","need":"a maker's figure or drawing; no page states either"},{"what":"a sentence that states the hammer and trigger pins' size: Aero says 'compatible with all mil-spec AR15 parts' and sells its complete lower on this receiver with a 'Mil-spec Lower Parts Kit'","need":"a seller's sentence naming .154 pins"}]},"aero-m4e1-threaded-upper":{"id":"aero-m4e1-threaded-upper","name":"M4E1 Threaded upper receiver","manufacturer":"Aero Precision","sku":"APAR700201C","url":"https://www.aeroprecisionusa.com/m4e1-threaded-stripped-upper-receiver-anodized-black","category":"upper","description":"Aero Precision's M4E1 Threaded stripped upper: a forged 7075-T6 flat-top receiver with the M4E1's body profile, \"threaded to accept a standard AR15 barrel nut\" and \"precision machined to work with all mil-spec AR15 parts\". Sold without a port door or forward assist.","weight":"aero-m4e1-threaded-upper.weight","fitments":{"label":"Sold","default":"stripped","options":{"stripped":{"label":"Stripped","sku":"APAR700201C","params":{},"source":"https://www.aeroprecisionusa.com/m4e1-threaded-stripped-upper-receiver-anodized-black"},"assembled":{"label":"Assembled","sku":"APAR700201AC","params":{},"weight":"aero-m4e1-threaded-upper.weight_assembled","source":"https://www.aeroprecisionusa.com/m4e1-threaded-assembled-upper-receiver-black"}}},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"pins":{"origin":[0,0,0]},"front_face":{"origin":["{.front_face_x}","{.bore_axis_above_pin}",0],"note":"The end of the barrel-nut thread on the bore axis, +x toward the muzzle: a barrel extension's flange seats here, and a handguard is placed from here."},"rear_face":{"origin":["{.receiver_rear_x}","{.bore_axis_above_pin}",0],"note":"The rear face on the bore axis, +x toward the muzzle: the bolt carrier's channel opens here. (The charging handle has its own anchor, handle_channel.)"},"handle_channel":{"origin":["{.handle_seat_x}","{.bore_axis_above_pin} + {.charging_handle_above_bore}",0],"note":"The charging handle's seat on its channel's axis, +x toward the muzzle: the front wall of the open notch under the rail's rear end, which the handle's shoulder stops against, at the notch's mid-height. (At the rear face until 2026-10-05: the handle hung 0.7 in behind where it belongs.)"},"top_rail":{"origin":["{.rail_slot0_x}","{.rail_top_above_pin}",0],"note":"The rail's top at its rearmost slot's centre, +x toward the muzzle (picatinny: index = slot number)."}},"interfaces":{"receiver_pins":{"type":"ar15.upper_lower","role":"upper","anchor":"pins","params":{"pin_spacing":"={std.ar15.pin_spacing}"},"flips":false},"barrel_extension":{"type":"ar15.barrel_extension","role":"receiver","anchor":"front_face","params":{},"flips":false},"handguard_mount":{"type":"ar15.handguard_mount","role":"receiver","anchor":"front_face","params":{"nut":"standard"},"flips":false,"note":"Aero: \"threaded to accept a standard AR15 barrel nut\"."},"carrier_channel":{"type":"ar15.carrier_channel","role":"receiver","anchor":"rear_face","params":{},"flips":false},"charging_handle_channel":{"type":"ar15.charging_handle_channel","role":"receiver","anchor":"handle_channel","params":{},"flips":false},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}","seam":"={.rail_front_x} - {.rail_slot0_x}","seam_parts":"the receiver's rail and the handguard's","seam_behind":"receiver","seam_ahead":"handguard"},"flips":false,"note":"Its own rail of 14 slots, read off Aero's side photo; the R-ONE's rail ahead of it is the handguard's own (its `top_rail`, since 2026-10-05)."}},"materials":{"receiver":{"label":"Receiver","finish":"anodized","recolorable":true,"color":"placeholder-black","options":{"black":{"label":"Anodized Black","finish":"anodized","color":"placeholder-black","sku":"APAR700201C","source":"https://www.aeroprecisionusa.com/m4e1-threaded-stripped-upper-receiver-anodized-black"},"fde":{"label":"FDE Cerakote","finish":"cerakote","color":"aero-fde-cerakote","sku":"APAR700202C","source":"https://www.aeroprecisionusa.com/m4e1-threaded-stripped-upper-receiver-fde"},"odg":{"label":"OD Green Anodized","finish":"anodized","color":"aero-od-green-anodize-7075","sheen":"matte","sku":"APAR700220C","source":"https://www.aeroprecisionusa.com/m4e1-stripped-threaded-upper-odg-ano"},"kodiak":{"label":"Kodiak Brown Anodized","finish":"anodized","color":"aero-kodiak-brown-7075","sheen":"matte","sku":"APAR700222C","source":"https://www.aeroprecisionusa.com/m4e1-threaded-stripped-upper-receiver-kodiak-brown-ano"},"sniper_grey":{"label":"Sniper Grey Cerakote","finish":"cerakote","color":"aero-sniper-grey-cerakote","sku":"APAR700272AC","source":"https://www.aeroprecisionusa.com/m4e1-threaded-assembled-upper-sniper-grey-cerakote"}},"default":"black","note":"Aero's words for each finish: \"Anodized Black\", \"Magpul FDE Cerakote\" (the FDE page's Finish row), \"OD Green Anodized\", \"Kodiak Brown Anodized\". Its list of stripped uppers (2026-10-06) has the M4E1 Threaded in these four and Uncoated (APAR700200C: bare aluminium, \"These parts are unfinished. Please ensure you apply a firearms appropriate finish\"), which is sold and not offered here: no finish type draws bare metal as machined. The numbers are the stripped receiver's (the assembled one in each finish has its own, and only the black's, APAR700201AC, is on file). Aero's pages name the assembled receiver also in OD Green Cerakote and Sniper Grey Cerakote, which the stripped one isn't listed in. Sniper Grey is offered since 2026-11-02 (the user: \"make sure we find an active listing for each part in gray before we add it\"), assembled only: Aero's own page for it (\"SKU: APAR700272AC\", \"Port Door and Forward Assist installed\", $195.00) listed it that day, out of stock with a back-in-stock notice, and every seller's page read had it out of stock too (AR15Discounts and Dirty Bird, $174.99); no stripped receiver in Sniper Grey is listed (Aero's search for it has none, its address answers 404), so its number is the assembled one's and its offers are for the assembled fitment: chosen stripped, it has no price. On Aero's two pictures of it (b3b5eb2376e4 its left, 8f4469a3a7aa its right; the same rig as the black one's and not that picture: the port door's wear and the hinge rod's end differ) the receiver is the Sniper Grey of Aero's stripped lower and handguards, and the port door, its hinge and spring and the forward assist are black: not drawn (the model is the stripped receiver, its port open), as on the black assembled one. OD Green Cerakote isn't offered. The black is unmatched (sealed black anodize: its look is the finish type's)."}},"components":{},"geometry":{"components":{"receiver":"aero-m4e1-threaded-upper.receiver.glb"},"approximations":["Its side outline (Aero's straight right side, framed by its lug holes) across its own section (2026-10-05, the user: \"look at the aero precision upper receiver model because it looks wrong as well\": it had been the mil-spec forging's round body with a waist under the rail). The rail's lower faces under its slots' floors are the standard's (MIL-STD-1913's, since 2026-10-12: the reference CAD set's model of a mil-spec forging, which gives the height of the dovetail's foot and the neck, has them a hundredth further out, and every clamp stood in them). Under the rail's neck a flat band each side as wide as the rail's head (0.84 across, from 0.35 to 0.65 in below the rail's top); from its lower edge a flat face sloping out to the body's widest, 1.18 across at the bore's level: the M4E1's \"billet look\", read where the faces meet on Aero's two side views and across on OpticsPlanet's view from above. Below the bore's level it is the mil-spec forging's round body (the Army drawing's 1.18), which no view on file shows of this receiver. Its ends are cut at the standard's rear and front faces (the photo's silhouette reads 0.02 to 0.03 in past each). Bored for the carrier at the drawing's 1.000, the ejection port cut where the drawing puts it (3.125 long, .25 R ends).","Its rear lower corner (2026-10-12): out where a lower's two rear walls stand, the arc they rise along (the Army's .750 R, drawing 8448608 sheet 1; the upper's own drawing has .760, a hundredth clear of them, which isn't drawn: it would be a slit across the rifle); between the walls, what the side outline has there, which hangs in the trough.","Its forward assist housing is a flat-faced block, as the photos have it: a face sloping down from the body to its outer face, the outer face upright from 1.20 to 0.92 above the pin line, a face sloping back in under it; from above its outer face runs straight from 1.67 in out at the receiver's rear in toward the front at the forward assist's own 20 degrees, and its rear is square to that. Its bore along that axis: the drawing's .509 to its .65 depth, then the .315 on into the receiver. The brass deflector is flat faces from its outline on the side photo out to one point, 1.47 in out, the housing's outer face running into it. Their reach is read on a 978 px photo taken from some 10 in above: good to a tenth of an inch.","Its left side (2026-10-13, read on Aero's left view of the FDE receiver, where the black one's wall is one tone): a flat upright pad along the foot of the wall from 3.08 to 6.20 in ahead of the takedown pin, its upper edge 0.66 above the pin line, with a middle length from 4.05 to 4.585 that stands further out and reaches 0.74; and the cam pin's boss, 5.14 ahead: an upright outer face 0.34 long from 1.21 to 1.52 above the pin line with a flat flank each side, a face sloping back from it to the band at 1.65, and an end each side sloping down to the band, 0.75 across. How far they stand out is in no view on file: each face is upright by its tone, and is drawn where the body as drawn is at the height of the edge it runs out on (the pad 0.096 and 0.121 in out from the lug wall, the boss 0.068 from the band; were the lower body the flat face the same photo suggests, the pad would be 0.075 and 0.098). The boss's two flanks are drawn alike (the rear one's reading has a shadow in it), its ends' undersides and the pad's ends square, and the face over the boss one flat where the photo has it in two tones (a strip 0.05 in tall along its upper edge, a brighter facet under it). A lower parts kit's bolt catch, a plate the app places by the standard's boss, stands partly inside the pad's rear length, as it stood partly inside the round body before: its paddle shows in front of the pad, as it does on a rifle.","Behind its rail's head the rail is the standard's tongue (2026-10-20, lib.rail_tongue: the reference model's, ±0.318 with a round end, its rearmost point where this receiver's photo has the rail's end, and two concave rounds out to the head's width by 0.4165 ahead of the pin, where the app's head begins): until then the head was drawn at its full width to the rail's end, square, and every charging handle's T stood in its two corners. The charging handle's channel is the standard's (lib.handle_channel: the Army drawing's tier and roof, 8448524 sheet 2, and the reference model's widths and its two upright rounds), and so is the notch the handle's block lies in at least (lib.handle_notch: the reference model's floor, roof and 45 degree corners); a handle rides on its guide lugs on the tier (std.ar15.charging_handle_axis_y), which this receiver's photo, reading the see-through notch's middle, agrees with within its ±. The latch's slot under the rail's rear end on the left is the Army drawing's pocket (8448524 Section D-D), where Aero's left views show it. Neither the channel nor the slot was drawn until 2026-10-20. Aero's flat band under the rail's neck runs on in its left views to the notch's front wall, where every handle's latch arm lies against a forging's side: how the M4E1 is relieved for it isn't in any view on file, and the latch's arm and the band share a little there (handle-channel.test.ts).","Not drawn: the break between the upper band and the sloped face, the port's door seat and its two hinge bosses, the hole for the forward assist's pin in the housing's top, and the markings. (As aluminium the model comes to about 9.2 oz where Aero's page says 6.9: 11.7 until 2026-10-20, before the channel over the bore was cut.) The housing's and the deflector's faces are flat between the edges the photos show; the part's have smaller breaks along them. The face under the housing's outer one isn't seen square on in any view: it is drawn as far from the forward assist's axis as the mil-spec forging's round housing stands, so the bore is inside it."],"ledger":["aero-m4e1-threaded-upper.receiver_rear_x","aero-m4e1-threaded-upper.front_face_x","aero-m4e1-threaded-upper.underside_y","aero-m4e1-threaded-upper.rail_top_above_pin","aero-m4e1-threaded-upper.bore_axis_above_pin","aero-m4e1-threaded-upper.side_half_width","aero-m4e1-threaded-upper.side_bottom_y","aero-m4e1-threaded-upper.shoulder_bottom_y","aero-m4e1-threaded-upper.fa_housing_out_rear","aero-m4e1-threaded-upper.deflector_out","aero-m4e1-threaded-upper.left_pad_top_y","aero-m4e1-threaded-upper.cam_boss_bottom_y"]},"profiles":{"side":{"plane":"xy","origin":"the takedown pin centre (the rifle frame origin), +x toward the muzzle","offset":{},"points":[[-0.649,0.903],[-0.607,0.743],[-0.498,0.55],[-0.368,0.419],[-0.221,0.331],[-0.214,-0.207],[-0.193,-0.22],[0.227,-0.221],[0.24,-0.208],[0.24,0.036],[0.224,0.061],[0.224,0.229],[0.338,0.25],[6.146,0.248],[6.159,0.227],[6.15,-0.009],[6.183,-0.101],[6.246,-0.173],[6.322,-0.215],[6.414,-0.215],[6.49,-0.182],[6.57,-0.094],[6.595,0.007],[6.587,0.243],[6.608,0.297],[6.684,0.297],[6.701,0.272],[6.718,0.297],[6.734,0.297],[6.751,0.272],[6.777,0.297],[6.818,0.272],[6.835,0.297],[6.852,0.297],[6.869,0.271],[6.886,0.297],[6.928,0.271],[6.945,0.297],[6.961,0.296],[6.978,0.271],[7.033,0.317],[7.059,0.561],[7.06,1.158],[7.035,1.427],[6.997,1.482],[6.98,1.465],[6.947,1.49],[6.922,1.465],[6.888,1.49],[6.863,1.465],[6.838,1.49],[6.812,1.465],[6.787,1.49],[6.77,1.465],[6.753,1.465],[6.728,1.491],[6.711,1.465],[6.669,1.482],[6.653,1.457],[6.611,1.457],[6.59,1.478],[6.599,2.067],[6.586,2.096],[6.393,2.088],[6.389,2.067],[6.414,2.067],[6.422,1.991],[6.376,1.97],[6.3,1.97],[6.216,1.971],[6.195,2],[6.196,2.084],[6.158,2.097],[6.006,2.089],[5.994,2.068],[6.019,2.068],[6.027,2.017],[6.015,1.979],[5.821,1.971],[5.8,1.992],[5.801,2.085],[5.754,2.098],[5.611,2.081],[5.632,2.01],[5.611,1.972],[5.418,1.972],[5.405,1.985],[5.405,2.086],[5.309,2.09],[5.212,2.078],[5.237,2.01],[5.216,1.972],[5.023,1.973],[5.01,1.985],[5.006,2.091],[4.897,2.091],[4.838,2.091],[4.825,2.078],[4.834,1.986],[4.821,1.973],[4.619,1.974],[4.611,2.091],[4.443,2.092],[4.43,2.079],[4.434,1.974],[4.224,1.974],[4.22,2.079],[4.208,2.092],[4.124,2.092],[4.056,2.092],[4.044,2.08],[4.039,1.975],[3.829,1.975],[3.817,2.004],[3.825,2.08],[3.813,2.093],[3.661,2.093],[3.649,2.08],[3.648,1.98],[3.619,1.967],[3.442,1.967],[3.422,2.005],[3.43,2.081],[3.417,2.093],[3.266,2.094],[3.254,2.081],[3.253,1.989],[3.224,1.968],[3.039,1.968],[3.026,1.981],[3.035,2.073],[3.022,2.094],[2.871,2.094],[2.858,2.082],[2.858,1.981],[2.837,1.968],[2.636,1.977],[2.64,2.074],[2.619,2.095],[2.476,2.095],[2.463,2.083],[2.463,1.982],[2.442,1.969],[2.249,1.97],[2.236,1.999],[2.245,2.075],[2.232,2.087],[2.073,2.088],[2.068,1.991],[2.047,1.97],[1.854,1.97],[1.841,1.983],[1.846,2.088],[1.677,2.088],[1.673,1.992],[1.652,1.971],[1.459,1.971],[1.446,1.984],[1.455,2.076],[1.442,2.089],[1.282,2.089],[1.278,2.001],[1.257,1.971],[1.064,1.972],[1.06,2.06],[1.076,2.068],[1.047,2.089],[-0.559,2.084],[-0.588,2.055],[-0.584,1.916],[-0.525,1.899],[0.013,1.898],[0.092,1.818],[0.092,1.667],[0.004,1.579],[-0.61,1.588],[-0.622,1.576],[-0.648,1.256]],"features":{"forward_assist_housing":[[[-0.627,1.449],[1.777,1.445],[1.903,1.344],[1.902,0.84],[1.524,0.714],[0.01,0.524],[-0.494,0.508],[-0.628,0.659]]],"deflector":[[[1.878,1.361],[2.324,1.579],[2.559,1.662],[2.744,1.611],[2.954,1.46],[2.953,0.838],[2.533,0.838],[1.903,1.092]]]},"scaleRefs":["std.ar15.pin_spacing"],"inputs":{"std.ar15.pin_spacing":6.375},"tolerance":0.01,"photo":"references/aero-m4e1-threaded-upper 4ffb4e8b026f (Aero's gallery: the M4E1 Threaded stripped upper's right side, straight on, 1000 x 630)","method":"luminance < 200, largest piece, holes filled; frame from the reviewed holes takedown, pivot (119.0 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.01 in with the extremes kept: 178 points (IoU 0.996 with the full outline); checks: x_min -0.649 ± 0.013 in vs aero-m4e1-threaded-upper.receiver_rear_x -0.621 ± 0.005 (confirmed): DISAGREES; y_max 2.098 ± 0.013 in vs aero-m4e1-threaded-upper.rail_top_above_pin 2.09 ± 0.02 (corroborated): agrees; features through the same placement (forward_assist_housing: the housing's outline from the right, the bore's opening at its rear; deflector: the brass deflector: its ridge from (342, 268) to the apex (423, 232), down to the port's rear corner) (tools/trace.py)","via":"harvest","note":"Its outer silhouette with the lug holes filled: the barrel nut's threads at its front, the ejection port and the forward assist inside it."}},"gaps":[{"what":"Its section below the bore's level (drawn as the mil-spec forging's round body; Aero's left view of the FDE receiver has one even dark tone from the widest line down to a crease 0.41 in above the pin line, a flat face sloping in, where the round meets the lug walls at 0.50), and how far out its upper band stands (read from above as level with the rail's head, within a pixel)","need":"A view of it square from the front or the rear with a known size in frame"},{"what":"Its forward assist housing's and its deflector's reach to better than a tenth of an inch (read on a small photo from above, taken from close)","need":"A view from above or from the rear at a larger size, or from further off"},{"what":"How far its left side's pad and cam pin boss stand out (each is drawn where the body as drawn is at the height of the edge it runs out on), the shape of the pad's ends and of the boss's flanks and undersides; and the port's door seat and hinge bosses (not drawn)","need":"A view from above, from below or from an end that shows the left wall in profile at a size to read (the obliques on file have the part 250 px long); the hinge bosses outlined on Aero's right view with a depth from the same"}]},"aero-mid-gas-tube":{"id":"aero-mid-gas-tube","name":"Gas tube, mid-length, stainless steel","manufacturer":"Aero Precision","sku":"APRH100144C","url":"https://www.aeroprecisionusa.com/gas-tube-mid-length-stainless-steel","category":"gas_tube","description":"Aero Precision's mid-length stainless gas tube, 11.75 in, with its roll pin.","weight":"aero-mid-gas-tube.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"block":{"origin":[0,0,0],"note":"The tube's gas hole, where it stands over the block's port, on the front run's axis. +x rearward (the block's own anchor is turned that way)."}},"interfaces":{"gas_tube":{"type":"ar15.gas_tube","role":"tube","anchor":"block","params":{},"flips":false},"gas_system":{"type":"ar15.gas_system","role":"tube","params":{"length":"mid"},"flips":false,"note":"Aero Precision names it \"Gas Tube, Mid-Length\". What the platform checks a gas tube against a barrel by (D83)."}},"materials":{"tube":{"label":"Gas tube","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"Aero: \"Stainless Steel Gas Tube for AR15 & AR10 rifles\"; bright in its photo (7b502f23841c), the plugged front end and the head with it. Aero's Melonite tube is another product (named in data/proposals/discovery/aero-556-upper.yaml). Bright metal isn't fitted to a photo: the app's natural stainless. One piece: the \"Roll pin included\" isn't drawn."}},"components":{},"geometry":{"model":"aero-mid-gas-tube.glb","components":{},"approximations":["Swept along its centre line at the Army drawing's diameter (8448567: .180, at the head and at the plugged front end) and Aero's published length: a level front run, a round, a straight slope, an equal round and a level rear run the drawing's .156 higher. Where the bend lies and how round it is are read on the tube's own side photo (it begins 3.61 in and ends 5.56 in from the rear end, its rounds about 4.2 in in radius, the slope between them 5.9 degrees); the drawing, which is of the rifle's tube, has rounds of 1.50. The model's centre line is held to the photo's traced outline within 0.02 in.","The front end as the drawing and the photo have it: closed by a plug, a groove pressed round it each side of the roll pin's cross hole (.078, .187 from the end, across the rifle), the gas hole (.125, .605 from the end) through the lower wall only. The grooves' places, width and depth are read on the photo, where each is two to three pixels: each is drawn as a smooth dip, and its real section isn't known. The gas hole doesn't show in this tube's photo: it is the drawing's. The plug is one piece with the tube, its length scaled off the drawing.","The rear end as the photo has it: a head a tenth of an inch long at the tube's diameter, and between it and a line 2.31 in from the rear end a stretch 0.008 in thinner (half a pixel in the photo; the carbine tube's four photos show the same stretch, 0.013 thinner). The stretch's two ends are drawn as square steps; which of the two stretches is the drawing's .180 isn't read, and the head and the tube ahead of the line are drawn at it.","Both end faces' rims are broken by 0.012 in, as large as the photo's blur.","The bore is what Aero's 0.64 oz leaves of a stainless tube of this length and diameter (0.130 in); the Army's section, drawn without a figure, has a smaller one (0.09). It shows only at the open rear end, inside the receiver.","Its diameter isn't measured on this tube: its photo reads it 16% thin against a white ground, and no page states it.","The roll pin that comes with it isn't drawn: it goes across the gas block through the tube's cross hole, and its length has no source. The plug's seam on the front end face isn't drawn either; it is inside the block's blind hole."],"ledger":["aero-mid-gas-tube.length","aero-mid-gas-tube.od","aero-mid-gas-tube.bend_offset","aero-mid-gas-tube.bend_radius","aero-mid-gas-tube.bend_start_from_rear","aero-mid-gas-tube.bend_end_from_rear","aero-mid-gas-tube.gas_hole_from_front","aero-mid-gas-tube.gas_hole_d","aero-mid-gas-tube.pin_hole_from_front","aero-mid-gas-tube.pin_hole_d","aero-mid-gas-tube.crimp_front_from_front","aero-mid-gas-tube.crimp_rear_from_front","aero-mid-gas-tube.crimp_width","aero-mid-gas-tube.crimp_depth","aero-mid-gas-tube.head_length","aero-mid-gas-tube.relief_end_from_rear","aero-mid-gas-tube.relief_depth","aero-mid-gas-tube.end_break","aero-mid-gas-tube.plug_length","aero-mid-gas-tube.bore"]},"profiles":{"side":{"plane":"xy","origin":"the front end face, at the height of the front run's underside: the part's frame is the gas hole's distance behind that face (gas_hole_from_front), on the front run's axis","offset":{},"points":[[0,0.078],[0.014,0.063],[0,0.049],[0.014,0.035],[0.014,0.007],[0.021,0],[6.425,0],[6.439,0.014],[6.608,0.014],[6.623,0.028],[6.707,0.028],[6.721,0.014],[6.75,0.042],[6.764,0.042],[6.792,0.014],[6.82,0.042],[6.848,0.042],[6.862,0.056],[6.877,0.042],[6.891,0.056],[6.989,0.056],[7.003,0.071],[7.088,0.071],[7.102,0.085],[7.243,0.085],[7.257,0.099],[7.37,0.099],[7.384,0.113],[7.483,0.113],[7.497,0.127],[7.61,0.127],[7.624,0.141],[7.737,0.141],[7.751,0.155],[8.329,0.155],[8.343,0.141],[8.358,0.141],[8.372,0.155],[8.4,0.155],[8.414,0.141],[8.442,0.141],[8.456,0.155],[8.809,0.155],[8.823,0.169],[8.95,0.169],[8.964,0.155],[9.345,0.155],[9.359,0.141],[9.387,0.169],[9.401,0.155],[9.416,0.155],[9.43,0.169],[9.458,0.169],[9.472,0.155],[9.5,0.155],[9.514,0.169],[9.528,0.169],[9.542,0.155],[9.684,0.155],[9.698,0.169],[11.63,0.169],[11.644,0.155],[11.687,0.155],[11.701,0.169],[11.736,0.176],[11.736,0.261],[11.75,0.275],[11.715,0.31],[7.864,0.31],[7.85,0.296],[7.695,0.296],[7.681,0.282],[7.554,0.282],[7.539,0.268],[7.427,0.268],[7.413,0.254],[7.3,0.254],[7.286,0.24],[7.159,0.24],[7.145,0.226],[7.06,0.226],[7.046,0.212],[6.933,0.212],[6.919,0.197],[6.792,0.197],[6.778,0.183],[6.665,0.183],[6.651,0.169],[6.524,0.169],[6.51,0.155],[4.507,0.155],[4.493,0.141],[4.394,0.141],[4.38,0.155],[3.378,0.155],[3.364,0.141],[3.308,0.141],[3.294,0.155],[3.265,0.155],[3.251,0.141],[2.927,0.141],[2.913,0.155],[2.786,0.155],[2.772,0.141],[2.179,0.141],[2.165,0.155],[2.151,0.155],[2.137,0.141],[1.728,0.141],[1.714,0.155],[1.7,0.155],[1.686,0.141],[0.783,0.141],[0.769,0.155],[0.642,0.155],[0.628,0.141],[0.416,0.141],[0.402,0.155],[0.36,0.155],[0.346,0.141],[0.303,0.141],[0.289,0.155],[0.275,0.155],[0.261,0.141],[0.233,0.141],[0.219,0.155],[0.12,0.155],[0.106,0.141],[0.092,0.141],[0.078,0.155],[0.035,0.155],[0.014,0.134],[0.014,0.092]],"scaleRefs":["aero-mid-gas-tube.length"],"inputs":{"aero-mid-gas-tube.length":11.75},"tolerance":0.006,"photo":"references/aero-mid-gas-tube 7b502f23841c (Aero's picture of the stainless mid-length tube, whole and level on white, 1000 x 630)","method":"luminance < 235, closing ×2, largest piece, holes filled; scale from aero-mid-gas-tube.length = 11.75 in (x-extent 833 px → 70.9 px/in); origin at x min, y min of the outline; Douglas-Peucker at 0.006 in with the extremes kept: 133 points (IoU 0.999 with the full outline); the picture has the plugged front end at the right and the rear run the higher: mirrored, the front end is at x 0 and the rear run above the front. Its runs lean 0.02 degrees in the picture: not turned. One scale reference, the tube's own published length between its end faces: nothing else of known size is in the picture; checks: width 11.750 ± 0.043 in vs aero-mid-gas-tube.length 11.75 ± 0.01 (confirmed): agrees; height (tooth tops, max over 0.05 in windows) along x [0.9, 5.4] 0.155 ± 0.042 in vs aero-mid-gas-tube.od 0.18 ± 0.002 (confirmed): agrees; (centre between the top (max over 0.05 in windows) along x [8.4, 9.3]) − (centre between the top (max over 0.05 in windows) along x [2.2, 5.5]) 0.155 ± 0.060 in vs aero-mid-gas-tube.bend_offset 0.156 ± 0.01 (confirmed): agrees (tools/trace.py)","via":"harvest","note":"The tube from its right side as it sits in a rifle, +x rearward: the plugged front end at x 0, the rear run the bend's drop above the front run. The outline is the silhouette at the 235 level, which reads the tube 16% thin (bright metal on white): its centre line is the reading, not its thickness. The grooves round the plugged end and the head are at the limit of the picture (a pixel is 0.014 in)."}},"gaps":[{"what":"Its outside diameter and its bore, as Aero makes them","need":"A figure from Aero or a seller, or a view of its end with something of known size in it: the diameter drawn is the Army's drawing's, the bore what Aero's weight leaves"},{"what":"A second photo of it","need":"Everything read on this tube is from one photograph (Aero's own, 70.7 px to the inch; its second file is the same photograph): a seller's picture of the mid-length tube, as the carbine tube has four, would check the bend's place and the two ends"},{"what":"The gas hole on this tube","need":"A view from below, or a side view sharp enough to show its notch: its place and size are the Army's drawing's, which the carbine tube's photos bear out for that tube"},{"what":"The roll pin it comes with","need":"Its length, from Aero or a seller: the pin goes in the .078 cross hole and isn't drawn"},{"what":"A mid-length tube's own drawing","need":"The package on file has the rifle's (8448567): where a mid-length tube's bend lies, and its rounds"},{"what":"The sections of the two grooves round the plug and of the relief behind the head","need":"A close photo of each end with a scale on the tube: the product photo has them at half a pixel to three"}]},"aero-r-one-10-3-handguard":{"id":"aero-r-one-10-3-handguard","name":"AR15 10.3\" R-ONE M-LOK handguard","manufacturer":"Aero Precision","sku":"APRA500703A","url":"https://www.aeroprecisionusa.com/ar15-10-3-atlas-r-one-m-lok-handguard-anodized-black","category":"handguard","description":"Aero Precision's 10.3 in R-ONE free-float M-LOK handguard: 6061-T6, a full top Picatinny rail, QD sockets at 3, 6 and 9 o'clock, mounted by its own barrel nut on a standard upper's thread. \"Compatible with mil-spec AR15 upper receivers and barrels\"; \"NOT Compatible with M4E1 Enhanced Upper Receivers\".","weight":"aero-r-one-10-3-handguard.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"mount":{"origin":[0,0,0],"note":"The receiver's front face on the bore axis, +x toward the muzzle."},"mlok":{"origin":["{.mlok_slot0_x}",0,0],"note":"On the handguard's axis (the bore's: its side faces stand either side of it, 0.74 out at the slots' level) at the rearmost M-LOK slot's centre (index 0), +x toward the muzzle; the faces are angles about this axis (M10)."},"top_rail":{"origin":["{.rear_x} + {.rail_slot0_from_rear}","{.rail_top_above_bore}",0],"note":"The rail's top at its rearmost slot's centre, +x toward the muzzle (picatinny: index = slot number). Its own rail: the receiver's is the receiver's."}},"interfaces":{"handguard_mount":{"type":"ar15.handguard_mount","role":"handguard","anchor":"mount","params":{"nut":"standard"},"flips":false,"note":"Aero: \"Compatible with mil-spec AR15 upper receivers and barrels\"; \"NOT Compatible with M4E1 Enhanced Upper Receivers\". It ships with its own barrel nut for the standard thread."},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}","beyond_seam":true,"seam_behind":"receiver","seam_ahead":"handguard"},"flips":false},"mlok":{"type":"mlok","role":"slots","anchor":"mlok","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_slots}","interval":"={std.mlok.interval}","face_distance":"={.side_top_width} / 2 + ({.width} - {.side_top_width}) / 2 * ({.rail_top_above_bore} - {.side_flat_top_below_rail_top}) / ({.side_flat_bottom_below_rail_top} - {.side_flat_top_below_rail_top})","bore":"={.inside_diameter}","reach_inside":"={.reach_inside}"},"faces":{"right":{"angle":90,"note":"the rifle's right side (+z)"},"left":{"angle":-90}},"flips":false,"note":"How far an accessory's nuts may reach inside depends on the barrel under it, another part: reach_inside has no figure yet, so that check reads as unmade."}},"materials":{"body":{"label":"Handguard","finish":"anodized","recolorable":true,"color":"placeholder-black","options":{"black":{"label":"Anodized Black","finish":"anodized","color":"placeholder-black","sku":"APRA500703A","source":"https://www.aeroprecisionusa.com/ar15-10-3-atlas-r-one-m-lok-handguard-anodized-black"},"odg":{"label":"OD Green Anodized","finish":"anodized","color":"aero-od-green-anodize-6061","sheen":"matte","sku":"APRA501396A","source":"https://www.aeroprecisionusa.com/ar15-10-3-atlas-r-one-m-lok-handguard-od-green-anodized"},"kodiak":{"label":"Kodiak Brown Anodized","finish":"anodized","color":"aero-kodiak-brown-6061","sheen":"matte","sku":"APRA501397A","source":"https://www.aeroprecisionusa.com/ar15-10-3-atlas-r-one-m-lok-handguard-kodiak-brown-anodized"},"odg_cerakote":{"label":"OD Green Cerakote","finish":"cerakote","color":"aero-od-green-cerakote","sku":"APRA501398A","source":"https://www.aeroprecisionusa.com/ar15-10-3-atlas-r-one-m-lok-handguard-od-green-cerakote"},"fde":{"label":"FDE Cerakote","finish":"cerakote","color":"aero-fde-cerakote-handguards","sku":"APRA500713A","source":"https://www.aeroprecisionusa.com/ar15-r-one-mlok-handguard"},"burnt_bronze":{"label":"Burnt Bronze Cerakote","finish":"cerakote","color":"aero-burnt-bronze-cerakote","sku":"APRA501399A","source":"https://www.aeroprecisionusa.com/ar15-10-3-atlas-r-one-m-lok-handguard-burnt-bronze-cerakote"},"sniper_grey":{"label":"Sniper Grey Cerakote","finish":"cerakote","color":"aero-sniper-grey-cerakote","sku":"APRA501400A","source":"https://www.aeroprecisionusa.com/ar15-10-3-atlas-r-one-m-lok-handguard-sniper-grey-cerakote"}},"default":"black","note":"Aero's configurable page pairs this length with these finishes and a number for each (Anodized Black, OD Green Anodized, Kodiak Brown Anodized, OD Green Cerakote, FDE Cerakote, Burnt Bronze Cerakote, Sniper Grey Cerakote; its Uncoated one isn't offered: no finish type draws bare metal as machined), and two pictures of each: one piece in each, as the 15 in is (the colours are the 15 in's presets for the same coats). The Sniper Grey checked: Aero's two pictures of this length in it (references/aero-r-one-10-3-handguard 30f27925e06a and 3097b3fca33d) read the clamp's side face #5e605f and #4e504f at the 15 in's regions ([60,309,180,327], [825,309,940,327]), where the 15 in's read #5e6163 and #4b4c4e: one coat, within three levels. Aero's own page for one finish gives the price where it was found; the others' pages aren't at the addresses their siblings are, and are priced by sellers or not at all."}},"components":{},"geometry":{"model":"aero-r-one-10-3-handguard.glb","components":{},"approximations":["Its traced side outline (Aero's straight side view, scaled by its rail's teeth) across its section, which is flat-sided all round (the 15 in's, by reference: an assumption, no view of this length's end being on file). Below the rail, nine faces: a flat at 6 o'clock 0.61 in across at the published 1.95 below the rail's top; two faces each side from it up to the side face, a shallow one (36 degrees from level) and a steep one (54), with an edge of 18 degrees between them 1.76 below the rail's top and 1.13 across (the user, of a model with one face there: \"each of the m-lok slots is on its own face on the bottom half ... each on their own plane with a slight edge/corner between them\"); a side face from 1.50 to 0.88 below the rail's top, which leans in 2 degrees toward its top (1.5 across its lower edges, the published width, and 1.455 across its upper); and one upper face each side, 50 degrees from level, up to the foot of the rail's neck. Every corner is read on the view from its muzzle end, scaled by the published width and height, and the edge between the lower faces on two three-quarter views as well.","Its rail's top is level with the receiver's (Aero: the receiver's rail \"blends seamlessly\" with it). In section the rail is the standard's head (MIL-STD-1913, Figure 1: a top flat 0.656 in across, 45 degree faces out to 0.835 a tenth of an inch down and in again) on a neck 0.62 across that stands upright from 0.22 to 0.38 below the rail's top, where the two upper faces leave it (2026-10-05, the user: \"Your rail height doesn't look quite right\": it had been a block of the top's width a quarter inch tall, and then the head with no neck under it, shorter still). The rounds under the head and at the neck's foot aren't drawn.","The rail's top is its flat, and its 25 slots are the standard's width and depth on the standard's pitch from the first's place, where a clamp is put, as the 15 in's are. Behind the first tooth the rail's body runs on at the floors' height for a slot's length, as the outline has it; the last tooth is as long as the outline has it (about 0.25 in on this length's view; the 15 in's 0.18). From above the rail is two rows of ears (the user, the same day: \"the pic rail on this handguard seems to have a unique shape\"): every lug's middle is cut, 0.365 in across; at every other lug down to a bridge 0.03 below the ears' tops, and at the lugs between right through, a window 0.54 long from bridge to bridge, rounded at its ends; the lug at the muzzle end is whole. Read on the two views from its ends. Which lugs are bridges is counted back from the muzzle end's, on a photo of an R-ONE whose length isn't stated, and the same pattern is drawn over the clamp, where a shorter one has two round holes instead.","It is a shell: its faces a wall in (0.1 in: the published widths) from the upper faces round under the floor, and up inside the rail's neck a channel 0.42 across with an arched top, the published inside height (1.65) above the floor and 0.2 under the rail's top, which the rail's windows open into. That is the opening the muzzle end shows; the walls are drawn one thickness all round and the channel the same from end to end, which no view on file shows (from the side less shows through the upper outer row of slots than through the others: there is more metal behind it than is drawn).","Not drawn: the lip round its front end, the clamp's wedge and bolt, the round bore its barrel nut goes in, and its markings. Behind where its underside comes down to the body's (the clamp), the steep lower faces run on down to the outline.","Four M-LOK slots on each side at the standard's size and pitch, from the first's position on the photo, with the short slot and the QD socket behind them; and the same row along the bottom flat. Two sellers state M-LOK slots and a socket at 6 o'clock, and the underside of a shorter R-ONE shows the same row of openings: where it stands along this one isn't seen, and is drawn where the sides' is (it isn't offered for mounting on). Four rows of eight thin slots each side, 0.903 in long and 0.22 across the face: two in the upper face, one in each lower face, down the middle of its own face, each cut square to it where Aero's side views have its opening.","Placed as the 15 in is, its clamp the family's (rear_x by reference): Aero's 10.3 in length back from this one's rail end agrees within 0.06 in."],"ledger":["aero-r-one-10-3-handguard.length","aero-r-one-10-3-handguard.width","aero-r-one-10-3-handguard.height","aero-r-one-10-3-handguard.inside_diameter","aero-r-one-10-3-handguard.inside_height","aero-r-one-10-3-handguard.bottom_flat_width","aero-r-one-10-3-handguard.side_top_width","aero-r-one-10-3-handguard.lower_edge_width","aero-r-one-10-3-handguard.lower_edge_below_rail_top","aero-r-one-10-3-handguard.rail_neck_width","aero-r-one-10-3-handguard.rail_neck_foot_below_rail_top","aero-r-one-10-3-handguard.rail_centre_gap","aero-r-one-10-3-handguard.rail_window_length","aero-r-one-10-3-handguard.rear_x"]},"profiles":{"side":{"plane":"xy","origin":"the rear end (against the receiver) and the rail's top","offset":{"x":"rear_x","y":"rail_top_above_bore"},"points":[[0,-0.933],[0,-1.484],[0.012,-1.496],[0.012,-1.636],[0.035,-1.801],[0.076,-1.83],[0.305,-1.848],[0.328,-1.883],[0.34,-2.082],[0.358,-2.135],[0.628,-2.135],[0.639,-2.147],[1.097,-2.147],[1.144,-2.123],[1.161,-2.094],[1.138,-2.047],[1.161,-2.035],[1.161,-2],[1.132,-1.971],[1.085,-1.959],[1.044,-1.883],[1.044,-1.824],[1.073,-1.795],[1.414,-1.795],[1.466,-1.824],[1.49,-1.859],[1.49,-1.93],[1.373,-2.129],[1.39,-2.147],[1.66,-2.147],[1.766,-2.112],[1.895,-2.1],[2.082,-2.053],[2.153,-2.053],[2.387,-2.006],[2.986,-2.006],[3.115,-1.971],[10.493,-1.971],[10.505,-1.959],[10.611,-1.959],[10.628,-1.93],[10.675,-1.625],[10.675,-1.507],[10.687,-1.496],[10.675,-0.792],[10.652,-0.686],[10.64,-0.44],[10.628,-0.428],[10.628,-0.088],[10.64,-0.065],[10.611,0],[10.353,0],[10.329,-0.117],[10.218,-0.111],[10.229,-0.088],[10.212,0],[9.966,0],[9.942,-0.117],[9.836,-0.117],[9.813,0],[9.578,0],[9.561,-0.018],[9.555,-0.117],[9.438,-0.117],[9.414,0],[9.191,0],[9.174,-0.018],[9.168,-0.117],[9.039,-0.117],[9.033,-0.029],[9.015,0],[8.804,0],[8.775,-0.053],[8.787,-0.111],[8.675,-0.129],[8.634,-0.111],[8.634,-0.018],[8.616,0],[8.405,0],[8.388,-0.053],[8.394,-0.117],[8.265,-0.117],[8.253,-0.129],[8.235,-0.111],[8.229,0],[8.018,0],[8.001,-0.018],[7.995,-0.117],[7.889,-0.117],[7.877,-0.129],[7.836,-0.111],[7.848,-0.088],[7.83,0],[7.631,0],[7.613,-0.018],[7.608,-0.117],[7.502,-0.117],[7.49,-0.129],[7.467,-0.129],[7.437,-0.088],[7.449,-0.041],[7.432,0],[7.244,0],[7.215,-0.041],[7.226,-0.053],[7.22,-0.117],[7.103,-0.117],[7.091,-0.129],[7.05,-0.123],[7.05,-0.018],[7.033,0],[6.845,0],[6.827,-0.018],[6.827,-0.111],[6.763,-0.129],[6.657,-0.129],[6.652,-0.018],[6.634,0],[6.458,0],[6.44,-0.018],[6.452,-0.053],[6.44,-0.088],[6.464,-0.111],[6.388,-0.129],[6.259,-0.129],[6.253,-0.018],[6.235,0],[6.071,0],[6.041,-0.029],[6.053,-0.111],[6.036,-0.129],[6.024,-0.117],[6,-0.129],[5.86,-0.129],[5.854,-0.018],[5.836,0],[5.672,0],[5.654,-0.018],[5.666,-0.111],[5.649,-0.129],[5.473,-0.129],[5.455,-0.111],[5.449,0],[5.285,0],[5.267,-0.018],[5.267,-0.111],[5.25,-0.129],[5.074,-0.129],[5.056,-0.111],[5.05,0],[4.886,0],[4.868,-0.018],[4.88,-0.111],[4.851,-0.129],[4.675,-0.129],[4.669,-0.018],[4.651,0],[4.487,0],[4.47,-0.029],[4.481,-0.111],[4.452,-0.129],[4.276,-0.129],[4.27,-0.018],[4.253,0],[4.088,0],[4.071,-0.053],[4.082,-0.111],[4.053,-0.129],[3.889,-0.129],[3.883,-0.018],[3.854,0],[3.689,0],[3.684,-0.111],[3.666,-0.129],[3.502,-0.129],[3.484,-0.111],[3.496,-0.029],[3.467,0],[3.302,0],[3.285,-0.018],[3.285,-0.111],[3.267,-0.129],[3.103,-0.129],[3.097,-0.018],[3.068,0],[2.903,0],[2.886,-0.018],[2.886,-0.111],[2.868,-0.129],[2.716,-0.129],[2.71,-0.018],[2.669,0],[2.505,0],[2.487,-0.029],[2.481,-0.129],[2.329,-0.129],[2.323,-0.029],[2.293,0],[2.106,0],[2.088,-0.018],[2.082,-0.117],[1.93,-0.117],[1.924,-0.018],[1.906,0],[1.707,0],[1.689,-0.029],[1.683,-0.117],[1.543,-0.117],[1.537,-0.018],[1.507,0],[1.308,0],[1.29,-0.111],[1.261,-0.129],[1.249,-0.117],[1.156,-0.117],[1.15,-0.029],[1.12,0],[0.909,0],[0.903,-0.1],[0.886,-0.117],[0.768,-0.117],[0.751,-0.018],[0.733,0],[0.522,0],[0.504,-0.018],[0.499,-0.117],[0.346,-0.117],[0.334,-0.129],[0.311,-0.117],[0.293,-0.135],[0.305,-0.405],[0.287,-0.422],[0.194,-0.422],[0.059,-0.452],[0.035,-0.522],[0.012,-0.921]],"scaleRefs":["aero-r-one-10-3-handguard.overall_length"],"inputs":{"aero-r-one-10-3-handguard.overall_length":10.687},"tolerance":0.01,"photo":"references/aero-r-one-10-3-handguard 3e023c5c8f00 (Aero's gallery: the R-ONE 10.3 in handguard from its left side, 1000 x 631)","method":"luminance < 200, largest piece, holes filled; scale from aero-r-one-10-3-handguard.overall_length = 10.687 in (x-extent 911 px → 85.2 px/in); origin at x min, y max of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 236 points (IoU 0.998 with the full outline) (tools/trace.py)","via":"harvest","note":"The slots are inside the outline (its holes filled); the model cuts its M-LOK slots."}},"gaps":[{"what":"The room inside its side faces before the barrel (reach_inside: what an M-LOK accessory's nuts may take)","need":"The barrel's diameter under the handguard at the slots, from a photo of the bare barrel or Aero's profile figures"},{"what":"Where its bottom row of M-LOK slots stands along it (stated at 6 o'clock, drawn where the sides' row is, not offered for mounting)","need":"A view of this R-ONE's underside, or the bottom row and a side row together in one photo"},{"what":"Its inside away from the muzzle end: how thick its walls are and how far along the channel under its rail runs (from the side less shows through its upper outer row of slots than the section as drawn would let through)","need":"A view into it from the receiver's end with no barrel nut in it, or its section from a drawing"},{"what":"Which of its rail's lugs are bridges along it, and what its rail has over the barrel nut (a shorter one has two round holes there)","need":"A view of it from straight above"},{"what":"Whether a low-profile gas block clears it","need":"A rule from Aero's sentence (\"Compatible with low profile gas blocks\") once a gas block's height is on file"}]},"aero-r-one-12-7-handguard":{"id":"aero-r-one-12-7-handguard","name":"AR15 12.7\" R-ONE M-LOK handguard","manufacturer":"Aero Precision","sku":"APRA500704A","url":"https://www.aeroprecisionusa.com/ar15-r-one-mlok-handguard","category":"handguard","description":"Aero Precision's 12.7 in R-ONE free-float M-LOK handguard: 6061-T6, a full top Picatinny rail, QD sockets at 3, 6 and 9 o'clock, mounted by its own barrel nut on a standard upper's thread. \"Compatible with mil-spec AR15 upper receivers and barrels\"; \"NOT Compatible with M4E1 Enhanced Upper Receivers\".","weight":"aero-r-one-12-7-handguard.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"mount":{"origin":[0,0,0],"note":"The receiver's front face on the bore axis, +x toward the muzzle."},"mlok":{"origin":["{.mlok_slot0_x}",0,0],"note":"On the handguard's axis (the bore's: its side faces stand either side of it, 0.74 out at the slots' level) at the rearmost M-LOK slot's centre (index 0), +x toward the muzzle; the faces are angles about this axis (M10)."},"top_rail":{"origin":["{.rear_x} + {.rail_slot0_from_rear}","{.rail_top_above_bore}",0],"note":"The rail's top at its rearmost slot's centre, +x toward the muzzle (picatinny: index = slot number). Its own rail: the receiver's is the receiver's."}},"interfaces":{"handguard_mount":{"type":"ar15.handguard_mount","role":"handguard","anchor":"mount","params":{"nut":"standard"},"flips":false,"note":"Aero: \"Compatible with mil-spec AR15 upper receivers and barrels\"; \"NOT Compatible with M4E1 Enhanced Upper Receivers\". It ships with its own barrel nut for the standard thread."},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}","beyond_seam":true,"seam_behind":"receiver","seam_ahead":"handguard"},"flips":false},"mlok":{"type":"mlok","role":"slots","anchor":"mlok","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_slots}","interval":"={std.mlok.interval}","face_distance":"={.side_top_width} / 2 + ({.width} - {.side_top_width}) / 2 * ({.rail_top_above_bore} - {.side_flat_top_below_rail_top}) / ({.side_flat_bottom_below_rail_top} - {.side_flat_top_below_rail_top})","bore":"={.inside_diameter}","reach_inside":"={.reach_inside}"},"faces":{"right":{"angle":90,"note":"the rifle's right side (+z)"},"left":{"angle":-90}},"flips":false,"note":"How far an accessory's nuts may reach inside depends on the barrel under it, another part: reach_inside has no figure yet, so that check reads as unmade."}},"materials":{"body":{"label":"Handguard","finish":"anodized","recolorable":true,"color":"placeholder-black","options":{"black":{"label":"Anodized Black","finish":"anodized","color":"placeholder-black","sku":"APRA500704A","source":"https://www.aeroprecisionusa.com/ar15-r-one-mlok-handguard"},"odg":{"label":"OD Green Anodized","finish":"anodized","color":"aero-od-green-anodize-6061","sheen":"matte","sku":"APRA501604A","source":"https://www.aeroprecisionusa.com/ar15-12-7-atlas-r-one-m-lok-handguard-od-green-anodized"},"kodiak":{"label":"Kodiak Brown Anodized","finish":"anodized","color":"aero-kodiak-brown-6061","sheen":"matte","sku":"APRA501605A","source":"https://www.aeroprecisionusa.com/ar15-12-7-atlas-r-one-m-lok-handguard-kodiak-brown-anodized"},"fde":{"label":"FDE Cerakote","finish":"cerakote","color":"aero-fde-cerakote-handguards","sku":"APRA500714A","source":"https://www.aeroprecisionusa.com/ar15-r-one-mlok-handguard"}},"default":"black","note":"Aero's configurable page pairs this length with these finishes and a number for each (Anodized Black, OD Green Anodized, Kodiak Brown Anodized, FDE Cerakote; its Uncoated one isn't offered: no finish type draws bare metal as machined), and two pictures of each: one piece in each, as the 15 in is (the colours are the 15 in's presets for the same coats). Aero's own page for one finish gives the price where it was found; the others' pages aren't at the addresses their siblings are, and are priced by sellers or not at all."}},"components":{},"geometry":{"model":"aero-r-one-12-7-handguard.glb","components":{},"approximations":["Its traced side outline (Aero's straight side view, scaled by its rail's teeth) across its section, which is flat-sided all round (the 15 in's, by reference: an assumption, no view of this length's end being on file). Below the rail, nine faces: a flat at 6 o'clock 0.61 in across at the published 1.95 below the rail's top; two faces each side from it up to the side face, a shallow one (36 degrees from level) and a steep one (54), with an edge of 18 degrees between them 1.76 below the rail's top and 1.13 across (the user, of a model with one face there: \"each of the m-lok slots is on its own face on the bottom half ... each on their own plane with a slight edge/corner between them\"); a side face from 1.50 to 0.88 below the rail's top, which leans in 2 degrees toward its top (1.5 across its lower edges, the published width, and 1.455 across its upper); and one upper face each side, 50 degrees from level, up to the foot of the rail's neck. Every corner is read on the view from its muzzle end, scaled by the published width and height, and the edge between the lower faces on two three-quarter views as well.","Its rail's top is level with the receiver's (Aero: the receiver's rail \"blends seamlessly\" with it). In section the rail is the standard's head (MIL-STD-1913, Figure 1: a top flat 0.656 in across, 45 degree faces out to 0.835 a tenth of an inch down and in again) on a neck 0.62 across that stands upright from 0.22 to 0.38 below the rail's top, where the two upper faces leave it (2026-10-05, the user: \"Your rail height doesn't look quite right\": it had been a block of the top's width a quarter inch tall, and then the head with no neck under it, shorter still). The rounds under the head and at the neck's foot aren't drawn.","The rail's top is its flat, and its 31 slots are the standard's width and depth on the standard's pitch from the first's place, where a clamp is put, as the 15 in's are. Behind the first tooth the rail's body runs on at the floors' height for a slot's length, as the outline has it; the last tooth is as long as the outline has it (about 0.23 in on this length's view; the 15 in's 0.18). From above the rail is two rows of ears (the user, the same day: \"the pic rail on this handguard seems to have a unique shape\"): every lug's middle is cut, 0.365 in across; at every other lug down to a bridge 0.03 below the ears' tops, and at the lugs between right through, a window 0.54 long from bridge to bridge, rounded at its ends; the lug at the muzzle end is whole. Read on the two views from its ends. Which lugs are bridges is counted back from the muzzle end's, on a photo of an R-ONE whose length isn't stated, and the same pattern is drawn over the clamp, where a shorter one has two round holes instead.","It is a shell: its faces a wall in (0.1 in: the published widths) from the upper faces round under the floor, and up inside the rail's neck a channel 0.42 across with an arched top, the published inside height (1.65) above the floor and 0.2 under the rail's top, which the rail's windows open into. That is the opening the muzzle end shows; the walls are drawn one thickness all round and the channel the same from end to end, which no view on file shows (from the side less shows through the upper outer row of slots than through the others: there is more metal behind it than is drawn).","Not drawn: the lip round its front end, the clamp's wedge and bolt, the round bore its barrel nut goes in, and its markings. Behind where its underside comes down to the body's (the clamp), the steep lower faces run on down to the outline.","Six M-LOK slots on each side at the standard's size and pitch, from the first's position on the photo, with the QD socket behind them (no short slot at this length, on either side view); and the same row along the bottom flat. Two sellers state M-LOK slots and a socket at 6 o'clock, and the underside of a shorter R-ONE shows the same row of openings: where it stands along this one isn't seen, and is drawn where the sides' is (it isn't offered for mounting on). Four rows of ten thin slots each side, 0.92 in long and 0.22 across the face: two in the upper face, one in each lower face, down the middle of its own face, each cut square to it where Aero's side views have its opening.","Placed as the 15 in is, its clamp the family's (rear_x by reference): Aero's 12.7 in length back from this one's rail end agrees within 0.06 in."],"ledger":["aero-r-one-12-7-handguard.length","aero-r-one-12-7-handguard.width","aero-r-one-12-7-handguard.height","aero-r-one-12-7-handguard.inside_diameter","aero-r-one-12-7-handguard.inside_height","aero-r-one-12-7-handguard.bottom_flat_width","aero-r-one-12-7-handguard.side_top_width","aero-r-one-12-7-handguard.lower_edge_width","aero-r-one-12-7-handguard.lower_edge_below_rail_top","aero-r-one-12-7-handguard.rail_neck_width","aero-r-one-12-7-handguard.rail_neck_foot_below_rail_top","aero-r-one-12-7-handguard.rail_centre_gap","aero-r-one-12-7-handguard.rail_window_length","aero-r-one-12-7-handguard.rear_x"]},"profiles":{"side":{"plane":"xy","origin":"the rear end (against the receiver) and the rail's top","offset":{"x":"rear_x","y":"rail_top_above_bore"},"points":[[0,-0.941],[0,-1.478],[0.014,-1.492],[0.028,-1.789],[0.092,-1.839],[0.304,-1.853],[0.339,-1.945],[0.354,-2.114],[0.375,-2.136],[0.785,-2.136],[0.799,-2.15],[1.068,-2.15],[1.16,-2.1],[1.146,-2.072],[1.16,-2.001],[1.075,-1.945],[1.047,-1.888],[1.047,-1.817],[1.068,-1.796],[1.393,-1.796],[1.421,-1.81],[1.471,-1.86],[1.471,-1.931],[1.358,-2.129],[1.379,-2.15],[1.605,-2.15],[1.747,-2.107],[2.072,-2.065],[2.086,-2.051],[2.327,-2.023],[2.341,-2.008],[2.977,-2.008],[3.062,-1.98],[11.067,-1.98],[11.082,-1.994],[11.096,-1.98],[11.506,-1.98],[11.52,-1.994],[11.562,-1.98],[11.605,-1.994],[11.69,-1.994],[11.704,-1.98],[12.029,-1.98],[12.072,-1.994],[12.114,-1.98],[12.128,-1.994],[12.213,-1.994],[12.227,-1.98],[12.241,-1.994],[12.948,-1.994],[12.97,-1.973],[12.984,-1.747],[12.998,-1.733],[12.998,-0.714],[12.984,-0.7],[12.984,-0.53],[12.97,-0.516],[12.97,-0.035],[12.948,-0.014],[12.722,-0.014],[12.701,-0.035],[12.694,-0.141],[12.567,-0.141],[12.56,-0.05],[12.538,-0.014],[12.326,-0.014],[12.319,-0.12],[12.27,-0.141],[12.185,-0.141],[12.164,-0.12],[12.164,-0.035],[12.142,-0.014],[11.93,-0.014],[11.923,-0.12],[11.902,-0.141],[11.859,-0.127],[11.789,-0.141],[11.768,-0.12],[11.768,-0.035],[11.746,-0.014],[11.548,-0.014],[11.527,-0.064],[11.527,-0.12],[11.449,-0.141],[11.421,-0.127],[11.393,-0.141],[11.371,-0.12],[11.371,-0.035],[11.35,-0.014],[11.152,-0.014],[11.145,-0.12],[11.124,-0.141],[11.096,-0.127],[10.983,-0.127],[10.975,-0.035],[10.954,-0.014],[10.756,-0.014],[10.742,-0.127],[10.629,-0.127],[10.615,-0.141],[10.579,-0.12],[10.579,-0.035],[10.558,-0.014],[10.374,-0.014],[10.353,-0.035],[10.367,-0.05],[10.353,-0.092],[10.367,-0.12],[10.332,-0.141],[10.318,-0.127],[10.19,-0.127],[10.183,-0.035],[10.162,-0.014],[9.978,-0.014],[9.964,-0.127],[9.794,-0.127],[9.787,-0.035],[9.766,-0.014],[9.582,-0.014],[9.582,-0.127],[9.398,-0.127],[9.391,-0.035],[9.37,-0.014],[9.186,-0.014],[9.172,-0.127],[9.031,-0.127],[9.017,-0.141],[8.995,-0.12],[8.995,-0.035],[8.974,-0.014],[8.79,-0.014],[8.79,-0.127],[8.606,-0.127],[8.585,-0.064],[8.599,-0.035],[8.578,-0.014],[8.408,-0.014],[8.394,-0.127],[8.196,-0.127],[8.182,-0.014],[8.012,-0.014],[7.998,-0.127],[7.8,-0.127],[7.786,-0.014],[7.616,-0.014],[7.602,-0.127],[7.404,-0.127],[7.39,-0.014],[7.22,-0.014],[7.206,-0.127],[7.022,-0.127],[7.001,-0.106],[7.015,-0.021],[6.994,0],[6.98,-0.014],[6.824,-0.014],[6.81,-0.127],[6.612,-0.127],[6.605,-0.05],[6.619,-0.021],[6.598,0],[6.584,-0.014],[6.428,-0.014],[6.414,-0.127],[6.23,-0.127],[6.216,-0.014],[6.032,-0.014],[6.018,-0.127],[5.82,-0.127],[5.82,0],[5.806,-0.014],[5.636,-0.014],[5.622,-0.127],[5.452,-0.127],[5.445,-0.021],[5.424,0],[5.396,-0.014],[5.297,-0.014],[5.283,0],[5.24,-0.014],[5.226,-0.127],[5.042,-0.127],[5.042,0],[4.887,0],[4.844,-0.014],[4.83,-0.127],[4.674,-0.127],[4.653,-0.106],[4.646,0],[4.491,0],[4.448,-0.014],[4.434,-0.127],[4.278,-0.127],[4.257,-0.106],[4.271,-0.021],[4.25,0],[4.095,0],[4.052,-0.014],[4.038,-0.127],[3.882,-0.127],[3.875,-0.021],[3.854,0],[3.699,0],[3.656,-0.014],[3.642,-0.127],[3.501,-0.127],[3.479,-0.106],[3.472,0],[3.303,0],[3.274,-0.014],[3.253,-0.035],[3.246,-0.127],[3.105,-0.127],[3.097,-0.021],[3.076,0],[2.921,0],[2.878,-0.014],[2.857,-0.05],[2.85,-0.127],[2.723,-0.127],[2.701,-0.106],[2.694,0],[2.525,0],[2.482,-0.014],[2.454,-0.127],[2.327,-0.127],[2.298,0],[2.143,0],[2.129,-0.014],[2.086,-0.014],[2.065,-0.078],[2.079,-0.106],[2.058,-0.127],[1.931,-0.127],[1.924,-0.021],[1.902,0],[1.747,0],[1.733,-0.014],[1.69,-0.014],[1.683,-0.106],[1.662,-0.127],[1.549,-0.127],[1.528,-0.106],[1.52,0],[1.294,-0.014],[1.287,-0.106],[1.266,-0.127],[1.167,-0.127],[1.146,-0.106],[1.146,-0.021],[1.124,0],[0.969,0],[0.955,-0.014],[0.912,-0.014],[0.891,-0.035],[0.884,-0.127],[0.771,-0.127],[0.743,0],[0.587,0],[0.509,-0.021],[0.488,-0.127],[0.297,-0.134],[0.311,-0.389],[0.29,-0.41],[0.248,-0.424],[0.134,-0.424],[0.12,-0.438],[0.078,-0.438],[0.057,-0.46],[0.042,-0.488],[0.042,-0.615],[0.028,-0.629],[0.014,-0.926]],"scaleRefs":["aero-r-one-12-7-handguard.overall_length"],"inputs":{"aero-r-one-12-7-handguard.overall_length":12.998},"tolerance":0.01,"photo":"references/aero-r-one-12-7-handguard 8bfd4875f09d (Aero's gallery: the R-ONE 12.7 in handguard from its left side, 1000 x 630)","method":"luminance < 200, largest piece, holes filled; scale from aero-r-one-12-7-handguard.overall_length = 12.998 in (x-extent 919 px → 70.7 px/in); origin at x min, y max of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 273 points (IoU 0.998 with the full outline) (tools/trace.py)","via":"harvest","note":"The slots are inside the outline (its holes filled); the model cuts its M-LOK slots."}},"gaps":[{"what":"The room inside its side faces before the barrel (reach_inside: what an M-LOK accessory's nuts may take)","need":"The barrel's diameter under the handguard at the slots, from a photo of the bare barrel or Aero's profile figures"},{"what":"Where its bottom row of M-LOK slots stands along it (stated at 6 o'clock, drawn where the sides' row is, not offered for mounting)","need":"A view of this R-ONE's underside, or the bottom row and a side row together in one photo"},{"what":"Its inside away from the muzzle end: how thick its walls are and how far along the channel under its rail runs (from the side less shows through its upper outer row of slots than the section as drawn would let through)","need":"A view into it from the receiver's end with no barrel nut in it, or its section from a drawing"},{"what":"Which of its rail's lugs are bridges along it, and what its rail has over the barrel nut (a shorter one has two round holes there)","need":"A view of it from straight above"},{"what":"Whether a low-profile gas block clears it","need":"A rule from Aero's sentence (\"Compatible with low profile gas blocks\") once a gas block's height is on file"}]},"aero-r-one-15-handguard":{"id":"aero-r-one-15-handguard","name":"AR15 15\" R-ONE M-LOK handguard","manufacturer":"Aero Precision","sku":"APRA500705A","url":"https://www.aeroprecisionusa.com/ar15-15-atlas-r-one-m-lok-handguard-anodized-black","category":"handguard","description":"Aero Precision's 15 in R-ONE free-float M-LOK handguard: 6061-T6, a full top Picatinny rail, QD sockets at 3, 6 and 9 o'clock, mounted by its own barrel nut on a standard upper's thread. \"Compatible with mil-spec AR15 upper receivers and barrels\"; \"NOT Compatible with M4E1 Enhanced Upper Receivers\".","weight":"aero-r-one-15-handguard.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"mount":{"origin":[0,0,0],"note":"The receiver's front face on the bore axis, +x toward the muzzle."},"mlok":{"origin":["{.mlok_slot0_x}",0,0],"note":"On the handguard's axis (the bore's: its side faces stand either side of it, 0.74 out at the slots' level) at the rearmost M-LOK slot's centre (index 0), +x toward the muzzle; the faces are angles about this axis (M10)."},"top_rail":{"origin":["{.rear_x} + {.rail_slot0_from_rear}","{.rail_top_above_bore}",0],"note":"The rail's top at its rearmost slot's centre, +x toward the muzzle (picatinny: index = slot number). Its own rail: the receiver's is the receiver's."}},"interfaces":{"handguard_mount":{"type":"ar15.handguard_mount","role":"handguard","anchor":"mount","params":{"nut":"standard"},"flips":false,"note":"Aero: \"Compatible with mil-spec AR15 upper receivers and barrels\"; \"NOT Compatible with M4E1 Enhanced Upper Receivers\". It ships with its own barrel nut for the standard thread."},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}","beyond_seam":true,"seam_behind":"receiver","seam_ahead":"handguard"},"flips":false},"mlok":{"type":"mlok","role":"slots","anchor":"mlok","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_slots}","interval":"={std.mlok.interval}","face_distance":"={.side_top_width} / 2 + ({.width} - {.side_top_width}) / 2 * ({.rail_top_above_bore} - {.side_flat_top_below_rail_top}) / ({.side_flat_bottom_below_rail_top} - {.side_flat_top_below_rail_top})","bore":"={.inside_diameter}","reach_inside":"={.reach_inside}"},"faces":{"right":{"angle":90,"note":"the rifle's right side (+z)"},"left":{"angle":-90}},"flips":false,"note":"How far an accessory's nuts may reach inside depends on the barrel under it, another part: reach_inside has no figure yet, so that check reads as unmade."}},"materials":{"body":{"label":"Handguard","finish":"anodized","recolorable":true,"color":"placeholder-black","options":{"black":{"label":"Anodized Black","finish":"anodized","color":"placeholder-black","sku":"APRA500705A","source":"https://www.aeroprecisionusa.com/ar15-15-atlas-r-one-m-lok-handguard-anodized-black"},"odg":{"label":"OD Green Anodized","finish":"anodized","color":"aero-od-green-anodize-6061","sheen":"matte","sku":"APRA501178A","source":"https://www.aeroprecisionusa.com/ar15-15-atlas-r-one-m-lok-handguard-od-green-anodized"},"kodiak":{"label":"Kodiak Brown Anodized","finish":"anodized","color":"aero-kodiak-brown-6061","sheen":"matte","sku":"APRA501401A","source":"https://www.aeroprecisionusa.com/ar15-15-atlas-r-one-m-lok-handguard-kodiak-brown-anodized"},"odg_cerakote":{"label":"OD Green Cerakote","finish":"cerakote","color":"aero-od-green-cerakote","sku":"APRA501402A","source":"https://www.aeroprecisionusa.com/ar15-15-atlas-r-one-m-lok-handguard-od-green-cerakote"},"socom_blue":{"label":"SOCOM Blue Cerakote","finish":"cerakote","color":"aero-socom-blue","sku":"APRA501643A","source":"https://www.aeroprecisionusa.com/r-one-m-lok-15-in-handguard-socom-blue"},"fde":{"label":"FDE Cerakote","finish":"cerakote","color":"aero-fde-cerakote-handguards","sku":"APRA500715A","source":"https://www.aeroprecisionusa.com/ar15-r-one-mlok-handguard"},"burnt_bronze":{"label":"Burnt Bronze Cerakote","finish":"cerakote","color":"aero-burnt-bronze-cerakote","sku":"APRA500775A","source":"https://www.aeroprecisionusa.com/ar15-r-one-mlok-handguard"},"sniper_grey":{"label":"Sniper Grey Cerakote","finish":"cerakote","color":"aero-sniper-grey-cerakote","sku":"APRA500765A","source":"https://www.aeroprecisionusa.com/ar15-r-one-mlok-handguard"}},"default":"black","note":"Aero's words for each finish: \"Anodized Black\", \"OD Green Anodized\", \"Kodiak Brown Anodized\", \"Magpul OD Cerakote\" (the OD Green Cerakote page's Finish row), \"SOCOM Blue Cerakote Finish\". Its mounting hardware (the barrel nut, the wedge's nuts and the turnbuckle screw: \"All hardware mounting parts are included\") is in none of Aero's photos and isn't drawn: its colour in each colourway isn't known. The black is unmatched (sealed black anodize). The configurable maker page (2026-10-28) now pairs the exact 15 in variants with their numbers: FDE Cerakote APRA500715A, Burnt Bronze Cerakote APRA500775A, Sniper Grey Cerakote APRA500765A. Its Finish choices call FDE \"Magpul FDE Cerakote\" and bronze \"Burnt Bronze Cerakote\". The new FDE, Burnt Bronze and Sniper Grey gallery pairs each show one coated body including the rail, with no separate mounting hardware: the body slot is the complete visible piece map. FDE and Burnt Bronze use the handguard presets fitted on these two products' own photographs (data/colors/aero.yaml), preserving the brighter receiver FDE. Sniper Grey reuses the existing maker preset: this part's right/left photos 2cdc199a1372 and 4c83842bb8a7 read #5e6163 and #4b4c4e on the side face, a 19-21-level spread. make color-match aero-colorways-check (2026-10-28), hero direction, rear side face [800,555,1040,630]: FDE renders #8e7663 for this part's photo mean #8c7663; Burnt Bronze #90755a for #91765b; Sniper Grey #5b5e5d for #545658, within eight levels and the spread of the two photos. All three were looked at in the hero direction and from the right."}},"components":{},"geometry":{"model":"aero-r-one-15-handguard.glb","components":{},"approximations":["Its traced side outline (Aero's straight side view, scaled by its rail's 37 teeth) across its section, which is flat-sided all round (2026-10-05, from photos of its ends the user sent; until then it was a round tube of the published \"outside diameter\", twice the metal). Below the rail, nine faces: a flat at 6 o'clock 0.61 in across at the published 1.95 below the rail's top; two faces each side from it up to the side face, a shallow one (36 degrees from level) and a steep one (54), with an edge of 18 degrees between them 1.76 below the rail's top and 1.13 across (the user, of a model with one face there: \"each of the m-lok slots is on its own face on the bottom half ... each on their own plane with a slight edge/corner between them\"); a side face from 1.50 to 0.88 below the rail's top, which leans in 2 degrees toward its top (1.5 across its lower edges, the published width, and 1.455 across its upper); and one upper face each side, 50 degrees from level, up to the foot of the rail's neck. Every corner is read on the view from its muzzle end, scaled by the published width and height, and the edge between the lower faces on two three-quarter views as well.","Its rail's top is level with the receiver's (Aero: the receiver's rail \"blends seamlessly\" with it). In section the rail is the standard's head (MIL-STD-1913, Figure 1: a top flat 0.656 in across, 45 degree faces out to 0.835 a tenth of an inch down and in again) on a neck 0.62 across that stands upright from 0.22 to 0.38 below the rail's top, where the two upper faces leave it (2026-10-05, the user: \"Your rail height doesn't look quite right\": it had been a block of the top's width a quarter inch tall, and then the head with no neck under it, shorter still). The rounds under the head and at the neck's foot aren't drawn.","The rail's top is its flat, and its 37 slots are the standard's width and depth on the standard's pitch from the first's place, where a clamp is put (2026-10-12). Until then they were the traced outline's own, a silhouette's: 0.10 in wide at the receiver's end and 0.22 at the lens's axis for the standard's 0.206, their floors 0.09 to 0.12 down for 0.118, and up to 0.044 in behind the pitch mid-rail (on it at both ends), so that a clamp's cross bolt stood in the teeth. Behind the first tooth the rail's body runs on at the floors' height for a slot's length, as the outline has it; the last tooth is as long as the outline has it (0.18 in). From above the rail is two rows of ears (the user, the same day: \"the pic rail on this handguard seems to have a unique shape\"): every lug's middle is cut, 0.365 in across; at every other lug down to a bridge 0.03 below the ears' tops, and at the lugs between right through, a window 0.54 long from bridge to bridge, rounded at its ends; the lug at the muzzle end is whole. Read on the two views from its ends. Which lugs are bridges is counted back from the muzzle end's, on a photo of an R-ONE whose length isn't stated, and the same pattern is drawn over the clamp, where a shorter one has two round holes instead.","It is a shell: its faces a wall in (0.1 in: the published widths) from the upper faces round under the floor, and up inside the rail's neck a channel 0.42 across with an arched top, the published inside height (1.65) above the floor and 0.2 under the rail's top, which the rail's windows open into. That is the opening the muzzle end shows; the walls are drawn one thickness all round and the channel the same from end to end, which no view on file shows (from the side less shows through the upper outer row of slots than through the others: there is more metal behind it than is drawn). As aluminium the model comes to 9.5 oz, where its page says 9.07 (the round tube came to 16.6).","Not drawn: the lip round its front end, the clamp's wedge and bolt, the round bore its barrel nut goes in, and its markings. Behind where its underside comes down to the body's (the clamp), the steep lower faces run on down to the outline.","Seven M-LOK slots on each side at the standard's size and pitch, from the first's position on the photo, with the short slot and the QD socket behind them; and the same row along the bottom flat. Two sellers state M-LOK slots and a socket at 6 o'clock, and the underside of a shorter R-ONE shows the same row of openings: where it stands along this one isn't seen, and is drawn where the sides' is (it isn't offered for mounting on). Four rows of twelve thin slots each side, 0.954 in long and 0.22 across the face: two in the upper face, one in each lower face, down the middle of its own face, each cut square to it where Aero's side views have its opening.","Placed by Aero's own rule for its length (from \"the point of contact at the receiver\" to the end of the last rail slot), which puts its outline's rear end, the ends of two tabs that reach back along the receiver's front ring, 0.763 in behind the receiver's face; the photos of the complete upper agree within 0.015 (2026-10-03: it had been 0.32 in too far forward)."],"ledger":["aero-r-one-15-handguard.length","aero-r-one-15-handguard.width","aero-r-one-15-handguard.height","aero-r-one-15-handguard.inside_diameter","aero-r-one-15-handguard.inside_height","aero-r-one-15-handguard.bottom_flat_width","aero-r-one-15-handguard.side_top_width","aero-r-one-15-handguard.lower_edge_width","aero-r-one-15-handguard.lower_edge_below_rail_top","aero-r-one-15-handguard.rail_neck_width","aero-r-one-15-handguard.rail_neck_foot_below_rail_top","aero-r-one-15-handguard.rail_centre_gap","aero-r-one-15-handguard.rail_window_length","aero-r-one-15-handguard.rear_x"]},"profiles":{"side":{"plane":"xy","origin":"the rear end (against the receiver) and the rail's top","offset":{"x":"rear_x","y":"rail_top_above_bore"},"points":[[0,-0.861],[0,-1.529],[0.017,-1.546],[0.033,-1.763],[0.075,-1.805],[0.125,-1.805],[0.142,-1.822],[0.276,-1.822],[0.309,-1.839],[0.351,-1.914],[0.351,-1.997],[0.368,-2.014],[0.376,-2.106],[0.51,-2.106],[0.526,-2.123],[1.011,-2.123],[1.028,-2.139],[1.045,-2.123],[1.095,-2.139],[1.128,-2.106],[1.203,-2.081],[1.17,-2.031],[1.17,-1.981],[1.12,-1.93],[1.086,-1.847],[1.128,-1.772],[1.396,-1.772],[1.454,-1.813],[1.471,-1.847],[1.471,-1.914],[1.437,-1.947],[1.437,-1.981],[1.371,-2.081],[1.371,-2.114],[1.412,-2.139],[1.446,-2.123],[1.646,-2.123],[1.713,-2.089],[1.88,-2.073],[1.897,-2.056],[1.997,-2.056],[2.014,-2.039],[2.081,-2.039],[2.098,-2.022],[2.281,-2.006],[2.298,-1.989],[2.933,-1.989],[2.95,-1.972],[3.05,-1.972],[3.067,-1.956],[6.56,-1.956],[6.577,-1.972],[6.627,-1.972],[6.644,-1.956],[6.777,-1.956],[6.794,-1.972],[13.597,-1.972],[13.613,-1.989],[15.318,-1.989],[15.343,-1.947],[15.343,-1.797],[15.36,-1.78],[15.36,-0.627],[15.343,-0.61],[15.343,-0.025],[15.318,0],[15.151,0],[15.126,-0.025],[15.118,-0.117],[15.068,-0.117],[15.051,-0.1],[15.001,-0.117],[14.976,-0.092],[14.951,0],[14.75,0],[14.733,-0.1],[14.583,-0.1],[14.574,-0.025],[14.549,0],[14.349,0],[14.34,-0.025],[14.357,-0.042],[14.332,-0.1],[14.182,-0.1],[14.165,0],[13.948,0],[13.931,-0.1],[13.781,-0.1],[13.764,0],[13.563,0],[13.563,-0.1],[13.379,-0.1],[13.363,0],[13.162,0],[13.145,-0.1],[12.978,-0.1],[12.962,0],[12.778,0],[12.778,-0.1],[12.577,-0.1],[12.56,0],[12.377,0],[12.36,-0.1],[12.176,-0.1],[12.159,0],[11.975,0],[11.975,-0.1],[11.792,-0.1],[11.775,0],[11.591,0],[11.574,-0.1],[11.39,-0.1],[11.374,0],[11.19,0],[11.19,-0.1],[10.989,-0.1],[10.973,0],[10.805,0],[10.789,-0.1],[10.588,-0.1],[10.571,0],[10.404,0],[10.388,-0.1],[10.187,-0.1],[10.17,0],[10.003,0],[9.987,-0.1],[9.786,-0.1],[9.786,0],[9.602,0],[9.585,-0.1],[9.402,-0.1],[9.385,0],[9.201,0],[9.184,-0.1],[9,-0.1],[9,0],[8.817,0],[8.8,-0.1],[8.616,-0.1],[8.599,0],[8.415,0],[8.399,-0.1],[8.198,-0.1],[8.198,0],[8.014,0],[7.998,-0.1],[7.83,-0.1],[7.814,0],[7.613,0],[7.596,-0.1],[7.413,-0.1],[7.413,0],[7.229,0],[7.204,-0.025],[7.22,-0.042],[7.195,-0.1],[7.045,-0.1],[7.028,0],[6.828,0],[6.819,-0.075],[6.794,-0.1],[6.644,-0.1],[6.619,-0.042],[6.635,-0.025],[6.627,0],[6.426,0],[6.41,-0.1],[6.259,-0.1],[6.243,0],[6.025,0],[6.009,-0.1],[5.858,-0.1],[5.841,0],[5.641,0],[5.616,-0.025],[5.607,-0.1],[5.474,-0.1],[5.457,0],[5.24,0],[5.223,-0.1],[5.073,-0.1],[5.073,0],[4.839,0],[4.822,-0.1],[4.688,-0.1],[4.672,0],[4.454,0],[4.429,-0.025],[4.421,-0.1],[4.304,-0.1],[4.287,0],[4.053,0],[4.036,-0.1],[3.903,-0.1],[3.894,-0.075],[3.911,-0.058],[3.886,0],[3.652,0],[3.635,-0.1],[3.518,-0.1],[3.502,0],[3.268,0],[3.251,-0.1],[3.134,-0.1],[3.117,0],[2.866,0],[2.85,-0.1],[2.749,-0.1],[2.733,0],[2.482,0],[2.465,-0.1],[2.365,-0.1],[2.332,0],[2.081,0],[2.064,-0.1],[1.981,-0.1],[1.947,0],[1.696,0],[1.663,-0.1],[1.579,-0.1],[1.563,0],[1.312,0],[1.287,-0.042],[1.279,-0.1],[1.195,-0.1],[1.178,0],[0.911,0],[0.894,-0.1],[0.811,-0.1],[0.802,-0.025],[0.777,0],[0.526,0],[0.493,-0.1],[0.301,-0.109],[0.301,-0.159],[0.318,-0.175],[0.318,-0.376],[0.292,-0.401],[0.109,-0.418],[0.067,-0.443],[0.05,-0.476],[0.05,-0.577],[0.033,-0.593],[0.017,-0.844]],"scaleRefs":["aero-r-one-15-handguard.overall_length"],"inputs":{"aero-r-one-15-handguard.overall_length":15.36},"tolerance":0.01,"photo":"references/aero-r-one-15-handguard 588ce841463f (Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630)","method":"luminance < 200, largest piece, holes filled; scale from aero-r-one-15-handguard.overall_length = 15.36 in (x-extent 919 px → 59.8 px/in); origin at x min, y max of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 245 points (IoU 0.999 with the full outline) (tools/trace.py)","via":"harvest","note":"The slots are inside the outline (its holes filled); the model cuts its M-LOK slots."}},"gaps":[{"what":"The room inside its side faces before the barrel (reach_inside: what an M-LOK accessory's nuts may take)","need":"The barrel's diameter under the handguard at the slots, from a photo of the bare barrel or Aero's profile figures"},{"what":"Where its bottom row of M-LOK slots stands along it (stated at 6 o'clock, drawn where the sides' row is, not offered for mounting)","need":"A view of a 15 in R-ONE's underside, or the bottom row and a side row together in one photo"},{"what":"Its inside away from the muzzle end: how thick its walls are and how far along the channel under its rail runs (from the side less shows through its upper outer row of slots than the section as drawn would let through)","need":"A view into it from the receiver's end with no barrel nut in it, or its section from a drawing"},{"what":"Which of its rail's lugs are bridges along a 15 in, and what its rail has over the barrel nut (a shorter one has two round holes there)","need":"A view of a 15 in R-ONE from straight above"},{"what":"Whether a low-profile gas block clears it","need":"A rule from Aero's sentence (\"Compatible with low profile gas blocks\") once a gas block's height is on file"}]},"aero-r-one-16-6-handguard":{"id":"aero-r-one-16-6-handguard","name":"AR15 16.6\" R-ONE M-LOK handguard","manufacturer":"Aero Precision","sku":"APRA500706A","url":"https://www.primaryarms.com/aero-precision-atlas-r-one-m-lok-ar-15-handguard-16-6in","category":"handguard","description":"Aero Precision's 16.6 in R-ONE free-float M-LOK handguard: 6061-T6, a full top Picatinny rail, QD sockets at 3, 6 and 9 o'clock, mounted by its own barrel nut on a standard upper's thread. \"Compatible with mil-spec AR15 upper receivers and barrels\"; \"NOT Compatible with M4E1 Enhanced Upper Receivers\".","weight":"aero-r-one-16-6-handguard.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"mount":{"origin":[0,0,0],"note":"The receiver's front face on the bore axis, +x toward the muzzle."},"mlok":{"origin":["{.mlok_slot0_x}",0,0],"note":"On the handguard's axis (the bore's: its side faces stand either side of it, 0.74 out at the slots' level) at the rearmost M-LOK slot's centre (index 0), +x toward the muzzle; the faces are angles about this axis (M10)."},"top_rail":{"origin":["{.rear_x} + {.rail_slot0_from_rear}","{.rail_top_above_bore}",0],"note":"The rail's top at its rearmost slot's centre, +x toward the muzzle (picatinny: index = slot number). Its own rail: the receiver's is the receiver's."}},"interfaces":{"handguard_mount":{"type":"ar15.handguard_mount","role":"handguard","anchor":"mount","params":{"nut":"standard"},"flips":false,"note":"Aero: \"Compatible with mil-spec AR15 upper receivers and barrels\"; \"NOT Compatible with M4E1 Enhanced Upper Receivers\". It ships with its own barrel nut for the standard thread."},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}","beyond_seam":true,"seam_behind":"receiver","seam_ahead":"handguard"},"flips":false},"mlok":{"type":"mlok","role":"slots","anchor":"mlok","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_slots}","interval":"={std.mlok.interval}","face_distance":"={.side_top_width} / 2 + ({.width} - {.side_top_width}) / 2 * ({.rail_top_above_bore} - {.side_flat_top_below_rail_top}) / ({.side_flat_bottom_below_rail_top} - {.side_flat_top_below_rail_top})","bore":"={.inside_diameter}","reach_inside":"={.reach_inside}"},"faces":{"right":{"angle":90,"note":"the rifle's right side (+z)"},"left":{"angle":-90}},"flips":false,"note":"How far an accessory's nuts may reach inside depends on the barrel under it, another part: reach_inside has no figure yet, so that check reads as unmade."}},"materials":{"body":{"label":"Handguard","finish":"anodized","recolorable":true,"color":"placeholder-black","options":{"black":{"label":"Anodized Black","finish":"anodized","color":"placeholder-black","sku":"APRA500706A","source":"https://www.aeroprecisionusa.com/ar15-r-one-mlok-handguard"},"fde":{"label":"FDE Cerakote","finish":"cerakote","color":"aero-fde-cerakote-handguards","sku":"APRA500716A","source":"https://www.aeroprecisionusa.com/ar15-r-one-mlok-handguard"}},"default":"black","note":"Aero's configurable page pairs this length with these finishes and a number for each (Anodized Black, FDE Cerakote; its Uncoated one isn't offered: no finish type draws bare metal as machined), and two pictures of each: one piece in each, as the 15 in is (the colours are the 15 in's presets for the same coats). Aero's pages for one finish aren't found for this length: priced by a seller."}},"components":{},"geometry":{"model":"aero-r-one-16-6-handguard.glb","components":{},"approximations":["Its traced side outline (Aero's straight side view, scaled by its rail's teeth) across its section, which is flat-sided all round (the 15 in's, by reference: an assumption, no view of this length's end being on file). Below the rail, nine faces: a flat at 6 o'clock 0.61 in across at the published 1.95 below the rail's top; two faces each side from it up to the side face, a shallow one (36 degrees from level) and a steep one (54), with an edge of 18 degrees between them 1.76 below the rail's top and 1.13 across (the user, of a model with one face there: \"each of the m-lok slots is on its own face on the bottom half ... each on their own plane with a slight edge/corner between them\"); a side face from 1.50 to 0.88 below the rail's top, which leans in 2 degrees toward its top (1.5 across its lower edges, the published width, and 1.455 across its upper); and one upper face each side, 50 degrees from level, up to the foot of the rail's neck. Every corner is read on the view from its muzzle end, scaled by the published width and height, and the edge between the lower faces on two three-quarter views as well.","Its rail's top is level with the receiver's (Aero: the receiver's rail \"blends seamlessly\" with it). In section the rail is the standard's head (MIL-STD-1913, Figure 1: a top flat 0.656 in across, 45 degree faces out to 0.835 a tenth of an inch down and in again) on a neck 0.62 across that stands upright from 0.22 to 0.38 below the rail's top, where the two upper faces leave it (2026-10-05, the user: \"Your rail height doesn't look quite right\": it had been a block of the top's width a quarter inch tall, and then the head with no neck under it, shorter still). The rounds under the head and at the neck's foot aren't drawn.","The rail's top is its flat, and its 41 slots are the standard's width and depth on the standard's pitch from the first's place, where a clamp is put, as the 15 in's are. Behind the first tooth the rail's body runs on at the floors' height for a slot's length, as the outline has it; the last tooth is as long as the outline has it (about 0.25 in on this length's view; the 15 in's 0.18). From above the rail is two rows of ears (the user, the same day: \"the pic rail on this handguard seems to have a unique shape\"): every lug's middle is cut, 0.365 in across; at every other lug down to a bridge 0.03 below the ears' tops, and at the lugs between right through, a window 0.54 long from bridge to bridge, rounded at its ends; the lug at the muzzle end is whole. Read on the two views from its ends. Which lugs are bridges is counted back from the muzzle end's, on a photo of an R-ONE whose length isn't stated, and the same pattern is drawn over the clamp, where a shorter one has two round holes instead.","It is a shell: its faces a wall in (0.1 in: the published widths) from the upper faces round under the floor, and up inside the rail's neck a channel 0.42 across with an arched top, the published inside height (1.65) above the floor and 0.2 under the rail's top, which the rail's windows open into. That is the opening the muzzle end shows; the walls are drawn one thickness all round and the channel the same from end to end, which no view on file shows (from the side less shows through the upper outer row of slots than through the others: there is more metal behind it than is drawn).","Not drawn: the lip round its front end, the clamp's wedge and bolt, the round bore its barrel nut goes in, and its markings. Behind where its underside comes down to the body's (the clamp), the steep lower faces run on down to the outline.","Eight M-LOK slots on each side at the standard's size and pitch, from the first's position on the photo, with the short slot and the QD socket behind them; and the same row along the bottom flat. Two sellers state M-LOK slots and a socket at 6 o'clock, and the underside of a shorter R-ONE shows the same row of openings: where it stands along this one isn't seen, and is drawn where the sides' is (it isn't offered for mounting on). Four rows of thirteen thin slots each side, 1.001 in long and 0.22 across the face: two in the upper face, one in each lower face, down the middle of its own face, each cut square to it where Aero's side views have its opening.","Placed as the 15 in is, its clamp the family's (rear_x by reference): Aero's 16.6 in length back from this one's rail end agrees within 0.06 in."],"ledger":["aero-r-one-16-6-handguard.length","aero-r-one-16-6-handguard.width","aero-r-one-16-6-handguard.height","aero-r-one-16-6-handguard.inside_diameter","aero-r-one-16-6-handguard.inside_height","aero-r-one-16-6-handguard.bottom_flat_width","aero-r-one-16-6-handguard.side_top_width","aero-r-one-16-6-handguard.lower_edge_width","aero-r-one-16-6-handguard.lower_edge_below_rail_top","aero-r-one-16-6-handguard.rail_neck_width","aero-r-one-16-6-handguard.rail_neck_foot_below_rail_top","aero-r-one-16-6-handguard.rail_centre_gap","aero-r-one-16-6-handguard.rail_window_length","aero-r-one-16-6-handguard.rear_x"]},"profiles":{"side":{"plane":"xy","origin":"the rear end (against the receiver) and the rail's top","offset":{"x":"rear_x","y":"rail_top_above_bore"},"points":[[0,-0.491],[0,-1.807],[0.046,-1.835],[0.158,-1.835],[0.176,-1.854],[0.278,-1.863],[0.278,-2.03],[0.297,-2.048],[0.306,-2.15],[1.047,-2.15],[1.057,-2.123],[1.038,-2.085],[1.094,-2.048],[1.094,-2.011],[1.047,-1.965],[1.029,-1.983],[0.992,-1.965],[0.973,-1.983],[0.927,-1.919],[0.945,-1.844],[0.992,-1.798],[1.4,-1.798],[1.464,-1.863],[1.464,-1.919],[1.409,-1.993],[1.335,-2.141],[1.566,-2.15],[1.585,-2.132],[1.659,-2.132],[1.678,-2.113],[1.752,-2.113],[1.77,-2.095],[1.863,-2.095],[1.882,-2.076],[1.956,-2.076],[1.974,-2.058],[2.067,-2.058],[2.085,-2.039],[2.16,-2.039],[2.178,-2.021],[2.326,-2.021],[2.345,-2.002],[2.901,-2.002],[2.92,-1.983],[3.012,-1.983],[3.031,-1.965],[16.841,-1.965],[16.869,-1.937],[16.869,-1.844],[16.887,-1.826],[16.887,-1.659],[16.906,-1.641],[16.906,-0.769],[16.887,-0.751],[16.887,-0.584],[16.869,-0.565],[16.869,-0.399],[16.85,-0.38],[16.869,-0.028],[16.841,0],[16.6,0],[16.572,-0.102],[16.545,-0.13],[16.526,-0.111],[16.489,-0.13],[16.461,-0.102],[16.461,-0.046],[16.433,0],[16.211,0],[16.202,-0.065],[16.174,-0.111],[16.081,-0.111],[16.053,-0.083],[16.044,0],[15.822,0],[15.794,-0.102],[15.766,-0.13],[15.692,-0.13],[15.664,-0.102],[15.655,0],[15.432,0],[15.404,-0.028],[15.423,-0.046],[15.404,-0.065],[15.404,-0.102],[15.377,-0.13],[15.303,-0.13],[15.275,-0.102],[15.265,0],[15.043,0],[15.015,-0.028],[15.015,-0.102],[14.987,-0.13],[14.913,-0.13],[14.885,-0.102],[14.876,0],[14.654,0],[14.626,-0.028],[14.617,-0.13],[14.505,-0.13],[14.496,-0.028],[14.468,0],[14.264,0],[14.237,-0.028],[14.227,-0.13],[14.116,-0.13],[14.088,-0.083],[14.079,0],[13.875,0],[13.847,-0.028],[13.838,-0.13],[13.727,-0.13],[13.699,-0.102],[13.69,0],[13.486,0],[13.458,-0.028],[13.449,-0.13],[13.319,-0.13],[13.3,0],[13.078,0],[13.06,-0.13],[12.93,-0.13],[12.92,-0.028],[12.893,0],[12.707,0],[12.679,-0.028],[12.679,-0.102],[12.652,-0.13],[12.54,-0.13],[12.513,-0.083],[12.531,-0.065],[12.503,0],[12.299,0],[12.29,-0.102],[12.262,-0.13],[12.151,-0.13],[12.123,-0.102],[12.114,0],[11.91,0],[11.873,-0.13],[11.743,-0.13],[11.725,0],[11.521,0],[11.493,-0.028],[11.484,-0.13],[11.354,-0.13],[11.345,-0.028],[11.317,0],[11.132,0],[11.095,-0.13],[10.965,-0.13],[10.937,-0.102],[10.928,0],[10.742,0],[10.715,-0.028],[10.705,-0.13],[10.557,-0.13],[10.538,0],[10.353,0],[10.325,-0.028],[10.316,-0.13],[10.168,-0.13],[10.158,-0.028],[10.131,0],[9.964,0],[9.936,-0.028],[9.927,-0.13],[9.778,-0.13],[9.751,-0.102],[9.741,0],[9.575,0],[9.547,-0.028],[9.547,-0.065],[9.528,-0.083],[9.547,-0.102],[9.537,-0.13],[9.371,-0.13],[9.352,0],[9.167,0],[9.139,-0.028],[9.13,-0.13],[8.981,-0.13],[8.972,-0.028],[8.944,0],[8.777,0],[8.75,-0.028],[8.74,-0.13],[8.592,-0.13],[8.564,-0.102],[8.583,-0.083],[8.583,-0.028],[8.555,0],[8.388,0],[8.36,-0.028],[8.351,-0.13],[8.184,-0.13],[8.166,0],[7.98,0],[7.962,-0.13],[7.795,-0.13],[7.786,-0.028],[7.758,0],[7.61,0],[7.582,-0.028],[7.572,-0.13],[7.406,-0.13],[7.378,-0.102],[7.396,-0.083],[7.378,-0.065],[7.396,-0.028],[7.369,0],[7.202,0],[7.174,-0.028],[7.192,-0.046],[7.183,-0.13],[6.998,-0.13],[6.979,0],[6.812,0],[6.785,-0.028],[6.775,-0.13],[6.609,-0.13],[6.599,-0.028],[6.571,0],[6.423,0],[6.395,-0.028],[6.386,-0.13],[6.219,-0.13],[6.191,-0.102],[6.21,-0.065],[6.191,-0.046],[6.21,-0.028],[6.182,0],[6.034,0],[6.006,-0.028],[5.997,-0.13],[5.811,-0.13],[5.793,0],[5.626,0],[5.608,-0.13],[5.422,-0.13],[5.413,-0.028],[5.385,0],[5.237,0],[5.209,-0.028],[5.209,-0.083],[5.228,-0.102],[5.2,-0.13],[5.033,-0.13],[5.005,-0.102],[4.996,0],[4.847,0],[4.82,-0.028],[4.81,-0.13],[4.625,-0.13],[4.607,0],[4.44,0],[4.421,-0.13],[4.236,-0.13],[4.208,-0.083],[4.226,-0.065],[4.226,-0.028],[4.199,0],[4.05,0],[4.032,-0.13],[3.846,-0.13],[3.819,-0.102],[3.809,0],[3.661,0],[3.633,-0.028],[3.624,-0.13],[3.439,-0.13],[3.429,-0.028],[3.402,0],[3.253,0],[3.235,-0.13],[3.049,-0.13],[3.04,-0.028],[3.012,0],[2.864,0],[2.855,-0.102],[2.827,-0.13],[2.642,-0.13],[2.623,0],[2.475,0],[2.447,-0.028],[2.438,-0.13],[2.252,-0.13],[2.243,-0.028],[2.215,0],[2.067,0],[2.048,-0.13],[1.863,-0.13],[1.835,-0.102],[1.854,-0.028],[1.826,0],[1.678,0],[1.65,-0.028],[1.641,-0.13],[1.474,-0.13],[1.446,-0.102],[1.464,-0.083],[1.464,-0.046],[1.437,0],[1.27,0],[1.251,-0.13],[1.066,-0.13],[1.038,-0.102],[1.057,-0.028],[1.029,0],[0.881,0],[0.871,-0.102],[0.843,-0.13],[0.658,-0.13],[0.649,-0.065],[0.667,-0.028],[0.64,0],[0.491,0],[0.463,-0.028],[0.454,-0.13],[0.26,-0.139],[0.26,-0.417],[0.158,-0.426],[0.139,-0.445],[0.046,-0.445]],"scaleRefs":["aero-r-one-16-6-handguard.overall_length"],"inputs":{"aero-r-one-16-6-handguard.overall_length":16.906},"tolerance":0.01,"photo":"references/aero-r-one-16-6-handguard 9218ad7902eb (Aero's gallery: the R-ONE 16.6 in handguard from its left side, 1000 x 631)","method":"luminance < 200, largest piece, holes filled; scale from aero-r-one-16-6-handguard.overall_length = 16.906 in (x-extent 912 px → 53.9 px/in); origin at x min, y max of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 324 points (IoU 0.999 with the full outline) (tools/trace.py)","via":"harvest","note":"The slots are inside the outline (its holes filled); the model cuts its M-LOK slots."}},"gaps":[{"what":"The room inside its side faces before the barrel (reach_inside: what an M-LOK accessory's nuts may take)","need":"The barrel's diameter under the handguard at the slots, from a photo of the bare barrel or Aero's profile figures"},{"what":"Where its bottom row of M-LOK slots stands along it (stated at 6 o'clock, drawn where the sides' row is, not offered for mounting)","need":"A view of this R-ONE's underside, or the bottom row and a side row together in one photo"},{"what":"Its inside away from the muzzle end: how thick its walls are and how far along the channel under its rail runs (from the side less shows through its upper outer row of slots than the section as drawn would let through)","need":"A view into it from the receiver's end with no barrel nut in it, or its section from a drawing"},{"what":"Which of its rail's lugs are bridges along it, and what its rail has over the barrel nut (a shorter one has two round holes there)","need":"A view of it from straight above"},{"what":"Whether a low-profile gas block clears it","need":"A rule from Aero's sentence (\"Compatible with low profile gas blocks\") once a gas block's height is on file"}]},"aero-r-one-7-3-handguard":{"id":"aero-r-one-7-3-handguard","name":"AR15 7.3\" R-ONE M-LOK handguard","manufacturer":"Aero Precision","sku":"APRA500701A","url":"https://www.aeroprecisionusa.com/ar15-7-atlas-r-one-m-lok-handguard-anodized-black","category":"handguard","description":"Aero Precision's 7.3 in R-ONE free-float M-LOK handguard: 6061-T6, a full top Picatinny rail, QD sockets at 3, 6 and 9 o'clock, mounted by its own barrel nut on a standard upper's thread. \"Compatible with mil-spec AR15 upper receivers and barrels\"; \"NOT Compatible with M4E1 Enhanced Upper Receivers\".","weight":"aero-r-one-7-3-handguard.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"mount":{"origin":[0,0,0],"note":"The receiver's front face on the bore axis, +x toward the muzzle."},"mlok":{"origin":["{.mlok_slot0_x}",0,0],"note":"On the handguard's axis (the bore's: its side faces stand either side of it, 0.74 out at the slots' level) at the rearmost M-LOK slot's centre (index 0), +x toward the muzzle; the faces are angles about this axis (M10)."},"top_rail":{"origin":["{.rear_x} + {.rail_slot0_from_rear}","{.rail_top_above_bore}",0],"note":"The rail's top at its rearmost slot's centre, +x toward the muzzle (picatinny: index = slot number). Its own rail: the receiver's is the receiver's."}},"interfaces":{"handguard_mount":{"type":"ar15.handguard_mount","role":"handguard","anchor":"mount","params":{"nut":"standard"},"flips":false,"note":"Aero: \"Compatible with mil-spec AR15 upper receivers and barrels\"; \"NOT Compatible with M4E1 Enhanced Upper Receivers\". It ships with its own barrel nut for the standard thread."},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}","beyond_seam":true,"seam_behind":"receiver","seam_ahead":"handguard"},"flips":false},"mlok":{"type":"mlok","role":"slots","anchor":"mlok","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_slots}","interval":"={std.mlok.interval}","face_distance":"={.side_top_width} / 2 + ({.width} - {.side_top_width}) / 2 * ({.rail_top_above_bore} - {.side_flat_top_below_rail_top}) / ({.side_flat_bottom_below_rail_top} - {.side_flat_top_below_rail_top})","bore":"={.inside_diameter}","reach_inside":"={.reach_inside}"},"faces":{"right":{"angle":90,"note":"the rifle's right side (+z)"},"left":{"angle":-90}},"flips":false,"note":"How far an accessory's nuts may reach inside depends on the barrel under it, another part: reach_inside has no figure yet, so that check reads as unmade."}},"materials":{"body":{"label":"Handguard","finish":"anodized","recolorable":true,"color":"placeholder-black","options":{"black":{"label":"Anodized Black","finish":"anodized","color":"placeholder-black","sku":"APRA500701A","source":"https://www.aeroprecisionusa.com/ar15-7-atlas-r-one-m-lok-handguard-anodized-black"},"odg":{"label":"OD Green Anodized","finish":"anodized","color":"aero-od-green-anodize-6061","sheen":"matte","sku":"APRA501393A","source":"https://www.aeroprecisionusa.com/ar15-7-3-atlas-r-one-m-lok-handguard-od-green-anodized"},"kodiak":{"label":"Kodiak Brown Anodized","finish":"anodized","color":"aero-kodiak-brown-6061","sheen":"matte","sku":"APRA501394A","source":"https://www.aeroprecisionusa.com/ar15-7-3-atlas-r-one-m-lok-handguard-kodiak-brown-anodized"},"odg_cerakote":{"label":"OD Green Cerakote","finish":"cerakote","color":"aero-od-green-cerakote","sku":"APRA501395A","source":"https://www.aeroprecisionusa.com/ar15-7-3-atlas-r-one-m-lok-handguard-od-green-cerakote"},"fde":{"label":"FDE Cerakote","finish":"cerakote","color":"aero-fde-cerakote-handguards","sku":"APRA500711A","source":"https://www.aeroprecisionusa.com/ar15-r-one-mlok-handguard"},"sniper_grey":{"label":"Sniper Grey Cerakote","finish":"cerakote","color":"aero-sniper-grey-cerakote","sku":"APRA500761A","source":"https://www.aeroprecisionusa.com/ar15-7-3-atlas-r-one-m-lok-handguard-sniper-grey-cerakote"}},"default":"black","note":"Aero's configurable page pairs this length with these finishes and a number for each (Anodized Black, OD Green Anodized, Kodiak Brown Anodized, OD Green Cerakote, FDE Cerakote, Sniper Grey Cerakote; its Uncoated one isn't offered: no finish type draws bare metal as machined), and two pictures of each: one piece in each, as the 15 in is (the colours are the 15 in's presets for the same coats). Aero's own page for one finish gives the price where it was found; the others' pages aren't at the addresses their siblings are, and are priced by sellers or not at all."}},"components":{},"geometry":{"model":"aero-r-one-7-3-handguard.glb","components":{},"approximations":["Its traced side outline (Aero's straight side view, scaled by its rail's teeth) across its section, which is flat-sided all round (the 15 in's, by reference: an assumption, no view of this length's end being on file). Below the rail, nine faces: a flat at 6 o'clock 0.61 in across at the published 1.95 below the rail's top; two faces each side from it up to the side face, a shallow one (36 degrees from level) and a steep one (54), with an edge of 18 degrees between them 1.76 below the rail's top and 1.13 across (the user, of a model with one face there: \"each of the m-lok slots is on its own face on the bottom half ... each on their own plane with a slight edge/corner between them\"); a side face from 1.50 to 0.88 below the rail's top, which leans in 2 degrees toward its top (1.5 across its lower edges, the published width, and 1.455 across its upper); and one upper face each side, 50 degrees from level, up to the foot of the rail's neck. Every corner is read on the view from its muzzle end, scaled by the published width and height, and the edge between the lower faces on two three-quarter views as well.","Its rail's top is level with the receiver's (Aero: the receiver's rail \"blends seamlessly\" with it). In section the rail is the standard's head (MIL-STD-1913, Figure 1: a top flat 0.656 in across, 45 degree faces out to 0.835 a tenth of an inch down and in again) on a neck 0.62 across that stands upright from 0.22 to 0.38 below the rail's top, where the two upper faces leave it (2026-10-05, the user: \"Your rail height doesn't look quite right\": it had been a block of the top's width a quarter inch tall, and then the head with no neck under it, shorter still). The rounds under the head and at the neck's foot aren't drawn.","The rail's top is its flat, and its 17 slots are the standard's width and depth on the standard's pitch from the first's place, where a clamp is put, as the 15 in's are. Behind the first tooth the rail's body runs on at the floors' height for a slot's length, as the outline has it; the last tooth is as long as the outline has it (about 0.37 in on this length's view; the 15 in's 0.18). From above the rail is two rows of ears (the user, the same day: \"the pic rail on this handguard seems to have a unique shape\"): every lug's middle is cut, 0.365 in across; at every other lug down to a bridge 0.03 below the ears' tops, and at the lugs between right through, a window 0.54 long from bridge to bridge, rounded at its ends; the lug at the muzzle end is whole. Read on the two views from its ends. Which lugs are bridges is counted back from the muzzle end's, on a photo of an R-ONE whose length isn't stated, and the same pattern is drawn over the clamp, where a shorter one has two round holes instead.","It is a shell: its faces a wall in (0.1 in: the published widths) from the upper faces round under the floor, and up inside the rail's neck a channel 0.42 across with an arched top, the published inside height (1.65) above the floor and 0.2 under the rail's top, which the rail's windows open into. That is the opening the muzzle end shows; the walls are drawn one thickness all round and the channel the same from end to end, which no view on file shows (from the side less shows through the upper outer row of slots than through the others: there is more metal behind it than is drawn).","Not drawn: the lip round its front end, the clamp's wedge and bolt, the round bore its barrel nut goes in, and its markings. Behind where its underside comes down to the body's (the clamp), the steep lower faces run on down to the outline.","Two M-LOK slots on each side at the standard's size and pitch, from the first's position on the photo, with the short slot and the QD socket behind them; and the same row along the bottom flat. Two sellers state M-LOK slots and a socket at 6 o'clock, and the underside of a shorter R-ONE shows the same row of openings: where it stands along this one isn't seen, and is drawn where the sides' is (it isn't offered for mounting on). Four rows of five thin slots each side, 0.845 in long and 0.22 across the face: two in the upper face, one in each lower face, down the middle of its own face, each cut square to it where Aero's side views have its opening.","Placed as the 15 in is, its clamp the family's (rear_x by reference): Aero's 7.3 in length back from this one's rail end agrees within 0.06 in."],"ledger":["aero-r-one-7-3-handguard.length","aero-r-one-7-3-handguard.width","aero-r-one-7-3-handguard.height","aero-r-one-7-3-handguard.inside_diameter","aero-r-one-7-3-handguard.inside_height","aero-r-one-7-3-handguard.bottom_flat_width","aero-r-one-7-3-handguard.side_top_width","aero-r-one-7-3-handguard.lower_edge_width","aero-r-one-7-3-handguard.lower_edge_below_rail_top","aero-r-one-7-3-handguard.rail_neck_width","aero-r-one-7-3-handguard.rail_neck_foot_below_rail_top","aero-r-one-7-3-handguard.rail_centre_gap","aero-r-one-7-3-handguard.rail_window_length","aero-r-one-7-3-handguard.rear_x"]},"profiles":{"side":{"plane":"xy","origin":"the rear end (against the receiver) and the rail's top","offset":{"x":"rear_x","y":"rail_top_above_bore"},"points":[[0,-0.889],[0,-1.526],[0.025,-1.808],[0.103,-1.837],[0.298,-1.849],[0.335,-2.134],[1.071,-2.143],[1.125,-2.114],[1.1,-2.064],[1.133,-2.031],[1.133,-1.998],[1.08,-1.961],[1.063,-1.969],[1.034,-1.94],[1.001,-1.849],[1.018,-1.808],[1.03,-1.795],[1.41,-1.795],[1.464,-1.841],[1.481,-1.89],[1.357,-2.122],[1.394,-2.151],[1.65,-2.143],[1.725,-2.118],[2.436,-2.01],[3.082,-2.002],[3.222,-1.969],[7.549,-1.969],[7.569,-1.899],[7.586,-1.675],[7.586,-0.773],[7.561,-0.434],[7.569,-0.037],[7.557,0],[7.201,-0.008],[7.185,-0.124],[7.036,-0.124],[7.015,-0.087],[7.023,-0.045],[7.011,0],[6.821,0],[6.8,-0.021],[6.796,-0.124],[6.639,-0.124],[6.614,0],[6.424,0],[6.411,-0.012],[6.411,-0.103],[6.436,-0.112],[6.407,-0.124],[6.242,-0.124],[6.221,-0.103],[6.217,0],[6.035,0],[6.022,-0.012],[6.018,-0.124],[5.845,-0.124],[5.82,0],[5.638,-0.008],[5.625,-0.037],[5.642,-0.045],[5.642,-0.112],[5.63,-0.124],[5.448,-0.124],[5.427,-0.095],[5.435,-0.029],[5.423,0],[5.249,0],[5.232,-0.124],[5.05,-0.124],[5.026,0],[4.86,0],[4.848,-0.012],[4.844,-0.124],[4.645,-0.124],[4.633,-0.087],[4.641,-0.012],[4.629,0],[4.463,0],[4.451,-0.012],[4.447,-0.124],[4.248,-0.124],[4.244,-0.012],[4.231,0],[4.066,0],[4.049,-0.124],[3.851,-0.124],[3.847,-0.012],[3.834,0],[3.669,0],[3.657,-0.021],[3.665,-0.112],[3.652,-0.124],[3.454,-0.124],[3.45,-0.045],[3.466,-0.029],[3.437,0],[3.272,0],[3.255,-0.124],[3.073,-0.124],[3.069,-0.021],[3.04,0],[2.883,0],[2.858,-0.124],[2.66,-0.124],[2.656,-0.045],[2.676,-0.041],[2.68,-0.021],[2.643,0],[2.486,0],[2.461,-0.124],[2.287,-0.124],[2.283,-0.012],[2.254,0],[2.089,0],[2.064,-0.124],[1.899,-0.124],[1.894,-0.012],[1.857,0],[1.692,0],[1.667,-0.124],[1.51,-0.124],[1.506,-0.021],[1.46,0],[1.295,0],[1.27,-0.124],[1.121,-0.124],[1.117,-0.037],[1.088,0],[0.898,0],[0.873,-0.124],[0.732,-0.124],[0.716,-0.008],[0.509,0],[0.488,-0.021],[0.484,-0.124],[0.294,-0.124],[0.281,-0.136],[0.281,-0.418],[0.062,-0.447],[0.033,-0.476]],"scaleRefs":["aero-r-one-7-3-handguard.overall_length"],"inputs":{"aero-r-one-7-3-handguard.overall_length":7.586},"tolerance":0.01,"photo":"references/aero-r-one-7-3-handguard af919473e69d (Aero's gallery: the R-ONE 7.3 in handguard from its left side, 1000 x 630)","method":"luminance < 200, largest piece, holes filled; scale from aero-r-one-7-3-handguard.overall_length = 7.586 in (x-extent 917 px → 120.9 px/in); origin at x min, y max of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 141 points (IoU 0.998 with the full outline) (tools/trace.py)","via":"harvest","note":"The slots are inside the outline (its holes filled); the model cuts its M-LOK slots."}},"gaps":[{"what":"The room inside its side faces before the barrel (reach_inside: what an M-LOK accessory's nuts may take)","need":"The barrel's diameter under the handguard at the slots, from a photo of the bare barrel or Aero's profile figures"},{"what":"Where its bottom row of M-LOK slots stands along it (stated at 6 o'clock, drawn where the sides' row is, not offered for mounting)","need":"A view of this R-ONE's underside, or the bottom row and a side row together in one photo"},{"what":"Its inside away from the muzzle end: how thick its walls are and how far along the channel under its rail runs (from the side less shows through its upper outer row of slots than the section as drawn would let through)","need":"A view into it from the receiver's end with no barrel nut in it, or its section from a drawing"},{"what":"Which of its rail's lugs are bridges along it, and what its rail has over the barrel nut (a shorter one has two round holes there)","need":"A view of it from straight above"},{"what":"Whether a low-profile gas block clears it","need":"A rule from Aero's sentence (\"Compatible with low profile gas blocks\") once a gas block's height is on file"}]},"aero-r-one-9-3-handguard":{"id":"aero-r-one-9-3-handguard","name":"AR15 9.3\" R-ONE M-LOK handguard","manufacturer":"Aero Precision","sku":"APRA500702A","url":"https://www.aeroprecisionusa.com/ar15-9-atlas-r-one-m-lok-handguard-anodized-black","category":"handguard","description":"Aero Precision's 9.3 in R-ONE free-float M-LOK handguard: 6061-T6, a full top Picatinny rail, QD sockets at 3, 6 and 9 o'clock, mounted by its own barrel nut on a standard upper's thread. \"Compatible with mil-spec AR15 upper receivers and barrels\"; \"NOT Compatible with M4E1 Enhanced Upper Receivers\".","weight":"aero-r-one-9-3-handguard.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"mount":{"origin":[0,0,0],"note":"The receiver's front face on the bore axis, +x toward the muzzle."},"mlok":{"origin":["{.mlok_slot0_x}",0,0],"note":"On the handguard's axis (the bore's: its side faces stand either side of it, 0.74 out at the slots' level) at the rearmost M-LOK slot's centre (index 0), +x toward the muzzle; the faces are angles about this axis (M10)."},"top_rail":{"origin":["{.rear_x} + {.rail_slot0_from_rear}","{.rail_top_above_bore}",0],"note":"The rail's top at its rearmost slot's centre, +x toward the muzzle (picatinny: index = slot number). Its own rail: the receiver's is the receiver's."}},"interfaces":{"handguard_mount":{"type":"ar15.handguard_mount","role":"handguard","anchor":"mount","params":{"nut":"standard"},"flips":false,"note":"Aero: \"Compatible with mil-spec AR15 upper receivers and barrels\"; \"NOT Compatible with M4E1 Enhanced Upper Receivers\". It ships with its own barrel nut for the standard thread."},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}","beyond_seam":true,"seam_behind":"receiver","seam_ahead":"handguard"},"flips":false},"mlok":{"type":"mlok","role":"slots","anchor":"mlok","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_slots}","interval":"={std.mlok.interval}","face_distance":"={.side_top_width} / 2 + ({.width} - {.side_top_width}) / 2 * ({.rail_top_above_bore} - {.side_flat_top_below_rail_top}) / ({.side_flat_bottom_below_rail_top} - {.side_flat_top_below_rail_top})","bore":"={.inside_diameter}","reach_inside":"={.reach_inside}"},"faces":{"right":{"angle":90,"note":"the rifle's right side (+z)"},"left":{"angle":-90}},"flips":false,"note":"How far an accessory's nuts may reach inside depends on the barrel under it, another part: reach_inside has no figure yet, so that check reads as unmade."}},"materials":{"body":{"label":"Handguard","finish":"anodized","recolorable":true,"color":"placeholder-black","options":{"black":{"label":"Anodized Black","finish":"anodized","color":"placeholder-black","sku":"APRA500702A","source":"https://www.aeroprecisionusa.com/ar15-9-atlas-r-one-m-lok-handguard-anodized-black"},"odg":{"label":"OD Green Anodized","finish":"anodized","color":"aero-od-green-anodize-6061","sheen":"matte","sku":"APRA501602A","source":"https://www.aeroprecisionusa.com/ar15-r-one-mlok-handguard"},"kodiak":{"label":"Kodiak Brown Anodized","finish":"anodized","color":"aero-kodiak-brown-6061","sheen":"matte","sku":"APRA501603A","source":"https://www.aeroprecisionusa.com/ar15-9-3-atlas-r-one-m-lok-handguard-kodiak-brown-anodized"},"fde":{"label":"FDE Cerakote","finish":"cerakote","color":"aero-fde-cerakote-handguards","sku":"APRA500712A","source":"https://www.aeroprecisionusa.com/ar15-r-one-mlok-handguard"}},"default":"black","note":"Aero's configurable page pairs this length with these finishes and a number for each (Anodized Black, OD Green Anodized, Kodiak Brown Anodized, FDE Cerakote; its Uncoated one isn't offered: no finish type draws bare metal as machined), and two pictures of each: one piece in each, as the 15 in is (the colours are the 15 in's presets for the same coats). Aero's own page for one finish gives the price where it was found; the others' pages aren't at the addresses their siblings are, and are priced by sellers or not at all."}},"components":{},"geometry":{"model":"aero-r-one-9-3-handguard.glb","components":{},"approximations":["Its traced side outline (Aero's straight side view, scaled by its rail's teeth) across its section, which is flat-sided all round (the 15 in's, by reference: an assumption, no view of this length's end being on file). Below the rail, nine faces: a flat at 6 o'clock 0.61 in across at the published 1.95 below the rail's top; two faces each side from it up to the side face, a shallow one (36 degrees from level) and a steep one (54), with an edge of 18 degrees between them 1.76 below the rail's top and 1.13 across (the user, of a model with one face there: \"each of the m-lok slots is on its own face on the bottom half ... each on their own plane with a slight edge/corner between them\"); a side face from 1.50 to 0.88 below the rail's top, which leans in 2 degrees toward its top (1.5 across its lower edges, the published width, and 1.455 across its upper); and one upper face each side, 50 degrees from level, up to the foot of the rail's neck. Every corner is read on the view from its muzzle end, scaled by the published width and height, and the edge between the lower faces on two three-quarter views as well.","Its rail's top is level with the receiver's (Aero: the receiver's rail \"blends seamlessly\" with it). In section the rail is the standard's head (MIL-STD-1913, Figure 1: a top flat 0.656 in across, 45 degree faces out to 0.835 a tenth of an inch down and in again) on a neck 0.62 across that stands upright from 0.22 to 0.38 below the rail's top, where the two upper faces leave it (2026-10-05, the user: \"Your rail height doesn't look quite right\": it had been a block of the top's width a quarter inch tall, and then the head with no neck under it, shorter still). The rounds under the head and at the neck's foot aren't drawn.","The rail's top is its flat, and its 22 slots are the standard's width and depth on the standard's pitch from the first's place, where a clamp is put, as the 15 in's are. Behind the first tooth the rail's body runs on at the floors' height for a slot's length, as the outline has it; the last tooth is as long as the outline has it (about 0.37 in on this length's view; the 15 in's 0.18). From above the rail is two rows of ears (the user, the same day: \"the pic rail on this handguard seems to have a unique shape\"): every lug's middle is cut, 0.365 in across; at every other lug down to a bridge 0.03 below the ears' tops, and at the lugs between right through, a window 0.54 long from bridge to bridge, rounded at its ends; the lug at the muzzle end is whole. Read on the two views from its ends. Which lugs are bridges is counted back from the muzzle end's, on a photo of an R-ONE whose length isn't stated, and the same pattern is drawn over the clamp, where a shorter one has two round holes instead.","It is a shell: its faces a wall in (0.1 in: the published widths) from the upper faces round under the floor, and up inside the rail's neck a channel 0.42 across with an arched top, the published inside height (1.65) above the floor and 0.2 under the rail's top, which the rail's windows open into. That is the opening the muzzle end shows; the walls are drawn one thickness all round and the channel the same from end to end, which no view on file shows (from the side less shows through the upper outer row of slots than through the others: there is more metal behind it than is drawn).","Not drawn: the lip round its front end, the clamp's wedge and bolt, the round bore its barrel nut goes in, and its markings. Behind where its underside comes down to the body's (the clamp), the steep lower faces run on down to the outline.","Four M-LOK slots on each side at the standard's size and pitch, from the first's position on the photo, with the QD socket behind them (no short slot at this length, on either side view); and the same row along the bottom flat. Two sellers state M-LOK slots and a socket at 6 o'clock, and the underside of a shorter R-ONE shows the same row of openings: where it stands along this one isn't seen, and is drawn where the sides' is (it isn't offered for mounting on). Four rows of seven thin slots each side, 0.892 in long and 0.22 across the face: two in the upper face, one in each lower face, down the middle of its own face, each cut square to it where Aero's side views have its opening.","Placed as the 15 in is, its clamp the family's (rear_x by reference): Aero's 9.3 in length back from this one's rail end agrees within 0.06 in."],"ledger":["aero-r-one-9-3-handguard.length","aero-r-one-9-3-handguard.width","aero-r-one-9-3-handguard.height","aero-r-one-9-3-handguard.inside_diameter","aero-r-one-9-3-handguard.inside_height","aero-r-one-9-3-handguard.bottom_flat_width","aero-r-one-9-3-handguard.side_top_width","aero-r-one-9-3-handguard.lower_edge_width","aero-r-one-9-3-handguard.lower_edge_below_rail_top","aero-r-one-9-3-handguard.rail_neck_width","aero-r-one-9-3-handguard.rail_neck_foot_below_rail_top","aero-r-one-9-3-handguard.rail_centre_gap","aero-r-one-9-3-handguard.rail_window_length","aero-r-one-9-3-handguard.rear_x"]},"profiles":{"side":{"plane":"xy","origin":"the rear end (against the receiver) and the rail's top","offset":{"x":"rear_x","y":"rail_top_above_bore"},"points":[[0,-0.886],[0,-1.526],[0.031,-1.788],[0.058,-1.814],[0.1,-1.824],[0.304,-1.84],[0.336,-1.914],[0.362,-2.118],[0.886,-2.129],[0.896,-2.139],[1.012,-2.129],[1.075,-2.139],[1.164,-2.102],[1.164,-2.071],[1.143,-2.05],[1.164,-1.987],[1.127,-1.95],[1.075,-1.95],[1.08,-1.924],[1.049,-1.872],[1.049,-1.809],[1.085,-1.782],[1.421,-1.793],[1.468,-1.84],[1.478,-1.914],[1.363,-2.102],[1.379,-2.139],[1.599,-2.139],[2.186,-2.003],[2.784,-2.003],[2.899,-1.961],[9.557,-1.971],[9.584,-1.788],[9.584,-1.515],[9.594,-1.505],[9.594,-0.938],[9.584,-0.928],[9.594,-0.886],[9.563,-0.393],[9.573,-0.026],[9.557,0],[9.201,0],[9.18,-0.115],[9.023,-0.115],[9.017,-0.016],[9.002,0],[8.813,0],[8.797,-0.016],[8.792,-0.115],[8.687,-0.126],[8.677,-0.115],[8.635,-0.126],[8.619,-0.11],[8.619,-0.016],[8.603,0],[8.414,0],[8.42,-0.058],[8.399,-0.1],[8.43,-0.11],[8.351,-0.126],[8.226,-0.115],[8.22,-0.016],[8.205,0],[8.026,0],[8.011,-0.016],[8.005,-0.115],[7.827,-0.115],[7.822,-0.016],[7.806,0],[7.628,0],[7.612,-0.026],[7.633,-0.047],[7.633,-0.11],[7.607,-0.126],[7.429,-0.115],[7.418,0],[7.24,0],[7.224,-0.016],[7.224,-0.11],[7.198,-0.126],[7.03,-0.115],[7.02,0],[6.842,0],[6.831,-0.115],[6.632,-0.115],[6.621,0],[6.454,0],[6.438,-0.016],[6.433,-0.115],[6.286,-0.126],[6.228,-0.11],[6.223,0],[6.055,0],[6.04,-0.016],[6.05,-0.089],[6.034,-0.115],[5.846,-0.115],[5.84,-0.016],[5.825,0],[5.657,0],[5.641,-0.016],[5.641,-0.11],[5.604,-0.126],[5.437,-0.115],[5.431,-0.058],[5.452,-0.037],[5.437,0],[5.258,0],[5.243,-0.058],[5.253,-0.11],[5.227,-0.126],[5.059,-0.115],[5.049,0],[4.86,0],[4.855,-0.079],[4.844,-0.11],[4.818,-0.126],[4.65,-0.115],[4.645,-0.047],[4.666,-0.037],[4.65,0],[4.461,0],[4.456,-0.11],[4.42,-0.126],[4.273,-0.115],[4.278,-0.026],[4.262,0],[4.074,0],[4.058,-0.016],[4.058,-0.11],[4.042,-0.126],[4.011,-0.115],[3.864,-0.126],[3.848,-0.11],[3.859,-0.047],[3.869,-0.047],[3.874,-0.105],[3.89,-0.058],[3.874,0],[3.675,0],[3.659,-0.026],[3.67,-0.037],[3.659,-0.11],[3.623,-0.126],[3.497,-0.115],[3.486,0],[3.277,0],[3.261,-0.11],[3.245,-0.126],[3.067,-0.115],[3.104,-0.1],[3.104,-0.016],[3.088,0],[2.878,0],[2.873,-0.11],[2.826,-0.126],[2.805,-0.115],[2.721,-0.126],[2.705,-0.11],[2.716,-0.026],[2.7,0],[2.49,0],[2.475,-0.026],[2.475,-0.11],[2.448,-0.126],[2.333,-0.115],[2.312,0],[2.092,0],[2.071,-0.115],[1.935,-0.115],[1.924,0],[1.704,0],[1.688,-0.016],[1.683,-0.115],[1.557,-0.115],[1.536,0],[1.305,0],[1.284,-0.115],[1.159,-0.115],[1.153,-0.016],[1.138,0],[0.907,0],[0.886,-0.115],[0.781,-0.115],[0.76,0],[0.519,0],[0.503,-0.026],[0.503,-0.1],[0.488,-0.115],[0.309,-0.115],[0.294,-0.131],[0.304,-0.404],[0.288,-0.419],[0.173,-0.419],[0.079,-0.44],[0.052,-0.467]],"scaleRefs":["aero-r-one-9-3-handguard.overall_length"],"inputs":{"aero-r-one-9-3-handguard.overall_length":9.594},"tolerance":0.01,"photo":"references/aero-r-one-9-3-handguard f4a8b5638442 (Aero's gallery: the R-ONE 9.3 in handguard from its left side, 1000 x 630)","method":"luminance < 200, largest piece, holes filled; scale from aero-r-one-9-3-handguard.overall_length = 9.594 in (x-extent 915 px → 95.4 px/in); origin at x min, y max of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 196 points (IoU 0.997 with the full outline) (tools/trace.py)","via":"harvest","note":"The slots are inside the outline (its holes filled); the model cuts its M-LOK slots."}},"gaps":[{"what":"The room inside its side faces before the barrel (reach_inside: what an M-LOK accessory's nuts may take)","need":"The barrel's diameter under the handguard at the slots, from a photo of the bare barrel or Aero's profile figures"},{"what":"Where its bottom row of M-LOK slots stands along it (stated at 6 o'clock, drawn where the sides' row is, not offered for mounting)","need":"A view of this R-ONE's underside, or the bottom row and a side row together in one photo"},{"what":"Its inside away from the muzzle end: how thick its walls are and how far along the channel under its rail runs (from the side less shows through its upper outer row of slots than the section as drawn would let through)","need":"A view into it from the receiver's end with no barrel nut in it, or its section from a drawing"},{"what":"Which of its rail's lugs are bridges along it, and what its rail has over the barrel nut (a shorter one has two round holes there)","need":"A view of it from straight above"},{"what":"Whether a low-profile gas block clears it","need":"A rule from Aero's sentence (\"Compatible with low profile gas blocks\") once a gas block's height is on file"}]},"aero-s-one-15-handguard":{"id":"aero-s-one-15-handguard","name":"AR15 15\" S-ONE M-LOK Handguard","manufacturer":"Aero Precision","sku":"APRA500105A","url":"https://www.aeroprecisionusa.com/ar15-15-atlas-s-one-m-lok-handguard-anodized-black","category":"handguard","description":"Aero Precision's 15 in S-ONE free-float M-LOK handguard: \"Machined from 6061-T6 aluminum\", \"Front and rear picatinny rail\" with the \"Eliminated center of top rail for weight reduction\" and \"Indexing grooves in 12:00 position for positive grip control\" between, a \"Quick disconnect sling socket at the 3, 6 and 9 o'clock positions\", mounted by its own barrel nut and taper lock (\"All hardware mounting parts are included with the purchase of an ATLAS Handguard\") on a standard upper's thread. \"Compatible with mil-spec AR15 upper receivers and barrels\"; \"NOT Compatible with M4E1 Enhanced Upper Receivers\"; \"Compatible with low profile gas blocks\".","weight":"aero-s-one-15-handguard.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"mount":{"origin":[0,0,0],"note":"The receiver's front face on the bore axis, +x toward the muzzle."},"mlok":{"origin":["{.mlok_slot0_x}","{.rail_top_above_bore} - {.mlok_row_below_rail_top}",0],"note":"At the rearmost M-LOK slot's centre (index 0) on the line the two side rows' middles are on, +x toward the muzzle: 0.04 in above the bore's axis as the side views read the rows (mlok_row_below_rail_top); the faces are angles about this line (M10)."},"top_rail":{"origin":["{.rail_slot0_x}","{.rail_top_above_bore}",0],"note":"The rear rail block's top at its rearmost slot's centre, +x toward the muzzle (picatinny: index = slot number). Its own rail: the receiver's is the receiver's."},"top_rail_front":{"origin":["{.rail_front_slot0_x}","{.rail_top_above_bore}",0],"note":"The front rail block's top at its rearmost slot's centre, +x toward the muzzle: 33 rail pitches ahead of the rear block's first slot, on the same grid."}},"interfaces":{"handguard_mount":{"type":"ar15.handguard_mount","role":"handguard","anchor":"mount","params":{"nut":"standard"},"flips":false,"note":"Aero, this part's page: \"Compatible with mil-spec AR15 upper receivers and barrels\"; \"NOT Compatible with M4E1 Enhanced Upper Receivers\"; \"ATLAS Handguards are designed to match seamlessly with our M4E1 Threaded Upper Receivers. Additionally, they are compatible with any Mil-Spec AR-15 upper receivers as well. However, they may not be compatible with billet upper receivers due to indexing tabs.\"; \"Please note: The ATLAS Handguards are NOT compatible with our M4E1 Enhanced Upper Receiver.\"; its specification row \"Handguard Barrel Nut: Yes, I am attaching this to a standard upper\". Wing Tactical: \"NOTE: The ATLAS S-ONE M-LOK Handguards are NOT compatible with Aero Precision Enhanced M4E1 Upper Receiver and uppers with build-in handguard mount.\" It ships with its own barrel nut for the standard thread (\"a custom engineered barrel nut\"; Wing Tactical: \"1x Barrel Nut 1x Barrel Nut Wrench 1x Mounting Hardware Kit\"). Aero's pages for its two Cerakote finishes (Sniper Grey, OD Green) have the specification row as \"Handguard Barrel Nut: No, I am attaching this to an enhanced upper\", twice over, while the Sniper Grey page's own text says \"NOT Compatible with M4E1 Enhanced Upper Receivers\" and \"All hardware mounting parts are included with the purchase of an ATLAS Handguard\": taken as a row left on those two pages from another product, and every finish as mounting the one way."},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_rear_slots}","beyond_seam":true,"seam_behind":"receiver","seam_ahead":"handguard"},"flips":false,"at":"at the receiver's end","note":"The rear block: four slots, at the receiver's end."},"top_rail_front":{"type":"picatinny","role":"rail","anchor":"top_rail_front","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_front_slots}","beyond_seam":true,"seam_behind":"receiver","seam_ahead":"handguard"},"flips":false,"at":"at the muzzle's end","note":"The front block: four slots, at the muzzle end."},"mlok":{"type":"mlok","role":"slots","anchor":"mlok","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_slots}","interval":"={std.mlok.interval}","face_distance":"={.side_top_width} / 2 + ({.width} - {.side_top_width}) / 2 * ({.mlok_row_below_rail_top} - {.side_flat_top_below_rail_top}) / ({.side_flat_bottom_below_rail_top} - {.side_flat_top_below_rail_top})","bore":"={.inside_diameter}","reach_inside":"={.reach_inside}"},"faces":{"right":{"angle":90,"note":"the rifle's right side (+z)"},"left":{"angle":-90}},"flips":false,"note":"How far an accessory's nuts may reach inside depends on the barrel under it, another part: reach_inside has no figure, so that check reads as unmade."}},"materials":{"body":{"label":"Handguard","finish":"anodized","recolorable":true,"color":"placeholder-black","options":{"black":{"label":"Anodized Black","finish":"anodized","color":"placeholder-black","sku":"APRA500105A","source":"https://www.aeroprecisionusa.com/ar15-15-atlas-s-one-m-lok-handguard-anodized-black"},"odg":{"label":"OD Green Anodized","finish":"anodized","color":"aero-od-green-anodize-6061","sheen":"matte","sku":"APRA501179A","source":"https://www.aeroprecisionusa.com/ar15-15-atlas-s-one-m-lok-handguard-od-green-anodized"},"kodiak":{"label":"Kodiak Brown Anodized","finish":"anodized","color":"aero-kodiak-brown-6061","sheen":"matte","sku":"APRA501392A","source":"https://www.aeroprecisionusa.com/ar15-15-atlas-s-one-m-lok-handguard-kodiak-brown-anodized"},"sniper_grey":{"label":"Sniper Grey Cerakote","finish":"cerakote","color":"aero-sniper-grey-cerakote","sku":"APRA500165A","source":"https://www.aeroprecisionusa.com/ar15-15-atlas-s-one-m-lok-handguard-sniper-grey-cerakote"},"odg_cerakote":{"label":"OD Green Cerakote","finish":"cerakote","color":"aero-od-green-cerakote","sku":"APRA501064A","source":"https://www.aeroprecisionusa.com/ar15-15-atlas-s-one-m-lok-handguard-od-green-cerakote"},"fde":{"label":"FDE Cerakote","finish":"cerakote","color":"aero-fde-cerakote-handguards","sku":"APRA500115A","source":"https://www.aeroprecisionusa.com/ar15-s-one-mlok-handguard"},"burnt_bronze":{"label":"Burnt Bronze Cerakote","finish":"cerakote","color":"aero-burnt-bronze-cerakote","sku":"APRA500175A","source":"https://www.aeroprecisionusa.com/ar15-s-one-mlok-handguard"}},"default":"black","note":"Aero's Finish row on each page: \"Anodized Black\", \"OD Green Anodized\", \"Kodiak Brown Anodized\", \"Sniper Grey Cerakote\", \"Magpul OD Cerakote\" (the OD Green Cerakote page). The four colours are Aero's presets already on file, each matched on Aero's photos of the same finish (data/colors/aero.yaml: the two anodizes and the OD Green Cerakote on the R-ONE of this length, a 6061 handguard like this one; the Sniper Grey on the M4E1 stripped lower): they aren't matched again here. Checked on this part (make color-match, the side face of the solid block at its rear in the hero direction against the same face in Aero's photo of each finish, 2026-10-13): Kodiak Brown renders #a98d80 where the photo reads #ad9185, Sniper Grey #5b5e5d for #5b5d5c, OD Green Cerakote #5a5546 for #645e50 (within the ten levels its preset says), and OD Green Anodized #8e835d for #9f9361: this part's one photo in that anodize is 17 levels lighter than the R-ONE's two the preset was fitted to. The black is unmatched (sealed black anodize). Its mounting hardware is in none of Aero's photos and isn't drawn. The configurable maker page (2026-10-28) now pairs the exact 15 in variants with their numbers: FDE Cerakote APRA500115A, Burnt Bronze Cerakote APRA500175A. Its Finish choices call FDE \"Magpul FDE Cerakote\" and bronze \"Burnt Bronze Cerakote\". The new FDE and Burnt Bronze gallery pairs each show one coated body including its two rail blocks and spine, with no separate mounting hardware: the body slot remains the complete visible piece map. Both use the handguard presets fitted on these two products' own photographs (data/colors/aero.yaml), preserving the brighter receiver FDE. make color-match aero-colorways-check (2026-10-28), hero direction, rear side face [800,555,1040,630]: FDE renders #8e7663 for this part's photo mean #8f7661; Burnt Bronze #90755a for #907558. Both were looked at in the hero direction and from the right."}},"components":{},"geometry":{"model":"aero-s-one-15-handguard.glb","components":{},"approximations":["Its section is the R-ONE's (aero-r-one-15-handguard): flat-sided all round, the standard's rail head (MIL-STD-1913, Figure 1) on an upright neck, one upper face each side, a side face that leans in 2 degrees toward its top, two lower faces each side with an edge between them, a bottom flat at the published 1.95 in below the rail's top. Its own photos give the side faces' two edges (0.885 and 1.51 below the rail's top), the neck's foot (0.38) and its width (0.594, from the receiver's end at the rail head's own scale), and that it has two lower faces a side (the muzzle end's silhouette turns 22 degrees in a three-quarter view); the other corners (the side faces' width at their tops, the edge between the lower faces, the bottom flat's width) are the R-ONE's figures by reference, read on a view square on to the R-ONE's end: no such view of an S-ONE is on file. Aero's Series row for both is \"R-ONE/S-ONE\", and Wing Tactical's table gives both the same four section figures.","Its top, read on Aero's two side views through the rail's own slots: a rail block at each end, each five lugs and four slots, both on one grid of the standard's pitch (the front block's first slot the 33rd pitch ahead of the rear block's first: the R-ONE's 37-slot rail with the 29 between left off); the slots are the standard's width and depth. From each block a ramp falls 0.24 in to the spine between them, each the traced outline's own run of points between the two ends the photos give it. The spine is the neck cut down to a flat top (0.62 across by the view from the receiver's end, drawn at the neck's 0.594), with nine ribs 0.03 high across it, one over each bar between two thin slots (Aero: \"Indexing grooves in 12:00 position for positive grip control\"): each drawn square across the spine with sloped ends, where the photos have their ends running down the spine's shoulders.","Each rail block from above is two rows of ears, as the view from the receiver's end has the rear block: every lug's middle is cut 0.40 in across (read on that view at the head's own scale; the R-ONE's reads 0.365); the first, third and fifth lug of each block down to a bridge 0.03 below the ears' tops (the R-ONE's step, by reference); the second and fourth open into a window with round ends from one bridge to the next, 0.54 in long (the R-ONE's length, by reference), which both three-quarter views from above show deep and dark between the ears and which is drawn cut down into the channel under the block, as the R-ONE's windows are; and the lug at the muzzle end whole.","It is a shell: its faces a wall in (0.1 in: the published widths) from the upper faces round under the floor. Under each rail block, up inside the neck, a channel 0.39 across with an arched top, the published inside height (1.65) above the floor, open at its end of the handguard (both end views show the arched opening under the head; the receiver end's is 0.41 across at the head's scale) and drawn as far as where its block's ramp begins. Under the spine the inside's roof is drawn flat, midway between the spine's top and the top of a gas tube's rear run, which passes under the spine's rear end a tenth of an inch under its top (the standard's height for the tube above the bore): a twentieth of metal and a twentieth of room. No view shows that roof; the published wall of a tenth can't be its thickness. As aluminium the model comes to 8.1 oz where its page says 7.95 (2% over, as the R-ONE's model is over its own): the walls are one thickness all round, which no view on file shows.","Seven M-LOK slots on each side at the standard's size and pitch, from the first's position on the photos, at the height the photos have the row (0.04 in above the bore's level), with the short slot and the QD socket behind them; and the same row along the bottom flat. Aero's page says a socket at 6 o'clock and Wing Tactical's \"M-LOK slots at 3, 6, and 9 o'clock positions\"; the view from the receiver's end shows openings along the floor and a close view of the underside the socket just ahead of the clamp: where that row stands along a 15 in isn't seen, and is drawn where the sides' is (it isn't offered for mounting on). Four rows of twelve thin slots each side, 0.93 in long and 0.22 across the face (the R-ONE's width): two in the upper face, one in each lower face, each cut square to its own face down its middle, where the R-ONE's rims read (this handguard's see-through windows match the R-ONE's within 0.012 in).","Placed by Aero's own rule for its length (from \"the point of contact at the receiver\" to the end of the last rail slot), which puts its outline's rear end, the ends of two tabs that reach back along the receiver's front ring, 0.766 in behind the receiver's face and its rail's rear face within 0.025 of the receiver's front shoulder. No photo of it on a receiver is on file.","Not drawn: the clamp's wedge (the two taper lock nuts and the turnbuckle screw), the barrel nut, the round bore the nut goes in and the thread inside it, the detent's set screw, the rounds under the rail's head and at the neck's foot, the crease across the clamp's side faces, and its markings. Behind where its underside comes down to the body's (the clamp), the steep lower faces run on down to the outline, and a step of 0.04 in under the first half inch of the body isn't drawn."],"ledger":["aero-s-one-15-handguard.length","aero-s-one-15-handguard.width","aero-s-one-15-handguard.height","aero-s-one-15-handguard.inside_diameter","aero-s-one-15-handguard.inside_height","aero-s-one-15-handguard.rail_neck_width","aero-s-one-15-handguard.side_flat_top_below_rail_top","aero-s-one-15-handguard.side_flat_bottom_below_rail_top","aero-s-one-15-handguard.spine_below_rail_top","aero-s-one-15-handguard.spine_roof_below_rail_top","aero-s-one-15-handguard.rail_front_slot0_from_slot0","aero-s-one-15-handguard.rear_x"]},"profiles":{"side":{"plane":"xy","origin":"the rear end (the tabs' ends, behind the receiver's shoulder) and the rail's top","offset":{"x":"rear_x","y":"rail_top_above_bore"},"points":[[0,-0.806],[0,-1.592],[0.013,-1.606],[0.027,-1.792],[0.047,-1.812],[0.113,-1.812],[0.127,-1.825],[0.22,-1.825],[0.233,-1.839],[0.26,-1.825],[0.3,-1.852],[0.32,-1.872],[0.333,-2.072],[0.353,-2.119],[0.74,-2.119],[0.753,-2.132],[1.073,-2.132],[1.093,-2.112],[1.066,-2.085],[1.146,-2.005],[1.113,-1.972],[1.059,-1.959],[1.033,-1.959],[1.006,-1.999],[0.999,-1.952],[0.959,-1.912],[1.013,-1.885],[1.013,-1.832],[1.059,-1.772],[1.392,-1.772],[1.466,-1.819],[1.492,-1.899],[1.372,-2.099],[1.379,-2.132],[1.632,-2.132],[1.899,-2.065],[2.139,-2.039],[2.285,-1.999],[2.925,-1.999],[3.071,-1.959],[15.29,-1.959],[15.31,-1.939],[15.31,-1.885],[15.323,-1.872],[15.337,-1.619],[15.35,-1.606],[15.35,-0.806],[15.337,-0.793],[15.323,-0.433],[15.31,-0.42],[15.323,-0.02],[15.263,0],[15.21,0],[15.197,-0.013],[15.183,0],[15.157,-0.013],[15.103,0],[15.084,-0.02],[15.084,-0.113],[15.05,-0.133],[15.01,-0.12],[14.957,-0.133],[14.924,-0.1],[14.924,-0.02],[14.85,0],[14.717,0],[14.697,-0.02],[14.684,-0.113],[14.597,-0.133],[14.557,-0.133],[14.524,-0.1],[14.517,-0.013],[14.464,-0.013],[14.451,0],[14.317,0],[14.297,-0.033],[14.297,-0.113],[14.237,-0.133],[14.157,-0.133],[14.124,-0.073],[14.124,-0.02],[14.064,0],[13.931,0],[13.911,-0.02],[13.911,-0.113],[13.824,-0.12],[13.811,-0.133],[13.758,-0.133],[13.738,-0.113],[13.731,-0.013],[13.678,0],[13.664,-0.013],[13.518,-0.013],[13.331,-0.16],[13.131,-0.24],[12.145,-0.24],[12.092,-0.213],[12.012,-0.213],[11.972,-0.24],[11.079,-0.24],[11.026,-0.213],[10.96,-0.213],[10.906,-0.24],[10.013,-0.24],[9.96,-0.213],[9.894,-0.213],[9.84,-0.24],[8.934,-0.24],[8.894,-0.213],[8.828,-0.213],[8.774,-0.24],[7.868,-0.24],[7.815,-0.213],[7.762,-0.213],[7.708,-0.24],[6.802,-0.24],[6.762,-0.213],[6.682,-0.213],[6.642,-0.24],[5.736,-0.24],[5.696,-0.213],[5.616,-0.213],[5.563,-0.24],[4.67,-0.24],[4.63,-0.213],[4.537,-0.213],[4.497,-0.24],[3.604,-0.24],[3.551,-0.213],[3.471,-0.213],[3.431,-0.24],[2.712,-0.24],[2.498,-0.16],[2.338,-0.04],[2.259,0],[2.099,0],[2.092,-0.087],[2.072,-0.12],[1.925,-0.12],[1.919,-0.02],[1.899,0],[1.712,0],[1.692,-0.02],[1.692,-0.073],[1.672,-0.12],[1.526,-0.12],[1.506,-0.047],[1.512,0],[1.312,0],[1.292,-0.02],[1.292,-0.1],[1.273,-0.12],[1.139,-0.12],[1.119,-0.1],[1.113,0],[0.913,0],[0.893,-0.02],[0.893,-0.1],[0.873,-0.12],[0.74,-0.12],[0.713,0],[0.513,0],[0.493,-0.02],[0.493,-0.1],[0.473,-0.12],[0.3,-0.12],[0.28,-0.14],[0.293,-0.153],[0.293,-0.393],[0.273,-0.413],[0.087,-0.426],[0.04,-0.46],[0.027,-0.606],[0.013,-0.62],[0.013,-0.793]],"scaleRefs":["aero-s-one-15-handguard.overall_length"],"inputs":{"aero-s-one-15-handguard.overall_length":15.35},"tolerance":0.01,"photo":"references/aero-s-one-15-handguard 44cb3b093489 (Sportsman's Warehouse's copy of Aero's gallery view 2: the S-ONE 15 in handguard from its left, 1200 x 1200)","method":"luminance < 128, largest piece, holes filled; scale from aero-s-one-15-handguard.overall_length = 15.35 in (x-extent 1152 px → 75.0 px/in); origin at x min, y max of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 175 points (IoU 0.999 with the full outline) (tools/trace.py)","via":"harvest","note":"The openings are inside the outline (its holes filled); the model cuts them."}},"gaps":[{"what":"The room inside its side faces before the barrel (reach_inside: what an M-LOK accessory's nuts may take)","need":"The barrel's diameter under the handguard at the slots, from a photo of the bare barrel or Aero's profile figures"},{"what":"Where its bottom row of M-LOK slots stands along it, and how many (stated at 6 o'clock, seen from inside and at the clamp, drawn where the sides' row is, not offered for mounting)","need":"A view of a 15 in S-ONE's underside, or the bottom row and a side row together in one photo"},{"what":"The corners of its section that only a view square on to an end shows (the side faces' width at their tops, the edge between the two lower faces, the bottom flat's width, a bridged lug's step, a window's length, a thin slot's width across its face): the R-ONE's figures by reference","need":"A view square on to an S-ONE's muzzle end, or its section from a drawing"},{"what":"Its inside away from its two ends: the roof under the spine (drawn midway between the spine's top and a gas tube's), how far the arched channel under each rail block runs, and how thick its walls are (the model is 2% heavier as aluminium than its page says)","need":"A view into it from an end with no barrel nut in it, or its section from a drawing"},{"what":"Its rail blocks' windows: how long each is and that it goes through to the channel under the block (deep and dark in the three-quarter views; the R-ONE's length by reference)","need":"A view of a 15 in S-ONE from straight above"},{"what":"Its mounting hardware's weight: Aero's page says 1.9 oz, Wing Tactical's table 4.72 oz, a third seller 12.67 oz with it (7.95 with 4.72)","need":"A scale reading of the barrel nut, the taper lock nuts and the screw, or a page that says what each figure weighs"},{"what":"Where it stops on a receiver (placed by Aero's rule for its length; no photo of it installed is on file)","need":"Aero's photo of the complete upper APAR700305M7 (an S-ONE on the M4E1 Threaded upper), which is on a host that refuses the reader"},{"what":"Whether a low-profile gas block clears it","need":"A rule from Aero's sentence (\"Compatible with low profile gas blocks\") once a gas block's height is checked against its inside"}]},"aimpoint-duty-rds-30mm-mount":{"id":"aimpoint-duty-rds-30mm-mount","name":"Duty RDS One-piece TNP Mount, 30 mm","manufacturer":"Aimpoint","sku":"200768","url":"https://store.theshootingcentre.com/aimpoint-duty-rds-2-moa-red-dot-reflex-sight-with-30-mm-one-piece-tnp-mount/","category":"optic_mount","description":"The lower of the two mounts Aimpoint sells the Duty RDS on: \"Duty RDS™ One-piece TNP Mount 30 mm\", the sight on it 200758, the mount alone 200768 (Aimpoint's label on its box). A Micro-footprint dot screws to its top; the Duty RDS on it has its axis 30 mm (1.18 in) over the rail, \"measured from top surface of mounting platform\" (Aimpoint's table, as The Shooting Centre prints it): an absolute co-witness height. Its locking bar clamps it by one screw, as the 39 mm mount's. The page linked is The Shooting Centre's, in the UK, for the pair: no seller on file sells either.","weight":"aimpoint-duty-rds-30mm-mount.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":[0,0,0],"note":"Mount frame: origin on the rail's top at the middle of the mount along the rail, +x forward, where its locking bar and its screw are in Aimpoint's left view of the pair (as on the 39 mm mount)."},"deck":{"origin":["{.deck_x}","{.deck_above_rail}",0],"note":"On the mount's top, the seam under a dot's foot, at the footprint's middle: where a Micro dot's base is put (D101)."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":"={.mount_length} / 2","clamp_front":"={.mount_length} / 2"},"flips":false,"note":"The mount's length about its middle (the frame's origin): one locking bar on one screw, as the 39 mm mount's."},"deck":{"type":"optic_footprint","role":"deck","anchor":"deck","params":{"pattern":"aimpoint_micro"},"flips":false,"note":"Cut for the Duty RDS, which has \"the same footprint as the Aimpoint Micro T-1/Micro T-2\" (T.REX ARMS; data/interfaces.yaml, optic_footprint)."}},"materials":{"mount":{"label":"Mount","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","note":"The 30 mm one-piece mount, its locking bar and the bar's screw: black in every picture (Aimpoint's table: \"Material Mounting Solution Aluminum\"; how it is finished isn't said). The screw is black, drawn with the mount."}},"components":{},"geometry":{"model":"aimpoint-duty-rds-30mm-mount.glb","components":{},"approximations":["Drawn as the 39 mm mount's outline in Aimpoint's left view of that pair, from its foot up to this mount's own deck (Aimpoint's 30 mm less the sight's axis over its base), from flank to flank: Aimpoint's left view of the 30 mm pair shows the same block under the same locking bar (0.482 in tall there and 0.476 on the 39 mm, at the scale the sight's own length gives) with its top a hair over the bar's, and nothing of the 39 mm mount's above it. Its own photographs are the check, not the source of its outline.","Its channel for the rail is the rail's own head in section (MIL-STD-1913's) from the rail's top down to the lower gauge line, and below that plain walls the rail's widest apart. No groove along its right side: Aimpoint's right view of the 30 mm pair shows a plain block. As wide as the sight's housing, as the 39 mm mount is taken to be."],"ledger":["aimpoint-duty-rds-30mm-mount.deck_above_rail","aimpoint-duty-rds-30mm-mount.mount_length","aimpoint-duty-rds-30mm-mount.clamp_below_rail","aimpoint-duty-rds.jaw_top_above_clamp_bottom"]},"profiles":{},"gaps":[{"what":"A seller on file for it, or for the sight on it (200758)","need":"A page at a seller on file with an offer for 200768 or 200758: The Shooting Centre (UK), Optics Trade (Slovenia) and a few European shops carry them"},{"what":"Its own outline and its deck's height as read on its own photographs, which come 0.025 in under Aimpoint's figure less the sight's own axis over its base","need":"A straight view of the mount alone, or a drawing"}]},"aimpoint-duty-rds-39mm-mount":{"id":"aimpoint-duty-rds-39mm-mount","name":"One-piece Torsion Nut Mount and Spacer, 39 mm","manufacturer":"Aimpoint","url":"https://bravocompanyusa.com/aimpoint-duty-rds-red-dot-sight-one-piece-torsion-nut-mount-39mm/","category":"optic_mount","description":"The mount Aimpoint sells the Duty RDS on for an AR-15: \"Keyed Surface Mount: One-Piece Torsion Nut 39 mm Mount\" (Aimpoint's sheet, ITEM NO. 200759); in the box, \"1x Torsion nut mount and spacer (39mm)\" (T.REX ARMS). A Micro-footprint dot screws to its top; the Duty RDS on it has its axis 39 mm over the rail, a Micro T-2 0.44 in lower. Its locking bar clamps it to the rail by one screw. The page linked is Bravo Company's for the pair: no page on file sells the mount alone.","weight":"aimpoint-duty-rds-39mm-mount.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":[0,0,0],"note":"Mount frame: origin on the rail's top at the middle of the mount along the rail, +x forward. The locking bar and its screw are at the mount's middle in Aimpoint's left profile, as the recoil stop under it is taken to be (the manual: \"With the recoil stop positioned in a groove of the Picatinny rail\"; where along the mount it lies isn't seen)."},"deck":{"origin":["{.deck_x}","{.deck_above_rail}",0],"note":"On the mount's top, the seam under a dot's foot, at the footprint's middle: where a Micro dot's base is put (D101)."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":"={.mount_length} / 2","clamp_front":"={.mount_length} / 2"},"flips":false,"note":"The mount's length about its middle (the frame's origin): one locking bar on one screw. The manual: \"Loosen the screw (12) using the Torx T10 tool (3), and clamp the locking bar (11) around the Picatinny rail.\", \"With the recoil stop positioned in a groove of the Picatinny rail, push the sight forward (towards muzzle) and tighten the screw using the tool.\", \"Proceed with another 1/4 to 1/2 turn until fully tightened (3 Nm / 2.2 ft·lb).\" The sheet: \"ONE-PIECE TORSION NUT MOUNT Affixes optic securely to MIL-STD-1913 Picatinny rails.\""},"deck":{"type":"optic_footprint","role":"deck","anchor":"deck","params":{"pattern":"aimpoint_micro"},"flips":false,"note":"Cut for the Duty RDS, which has \"the same footprint as the Aimpoint Micro T-1/Micro T-2\" (T.REX ARMS; data/interfaces.yaml, optic_footprint)."}},"materials":{"mount":{"label":"Mount","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","note":"The 39 mm one-piece mount, its locking bar and the bar's screw: black in every picture (the sheet: \"Material Mount & Spacer (Standard Conf): High strength aluminum\"; how it is finished isn't said). The screw is black, drawn with the mount."}},"components":{},"geometry":{"model":"aimpoint-duty-rds-39mm-mount.glb","components":{},"approximations":["Built with the sight from Aimpoint's own left profile of 200759 (the pair's outline) and its right profile (where the groove along the mount is): no view from the front, the rear or above is on file, so the mount is taken to be as wide as the sight's housing.","The mount is its outline under the seam beneath the sight's foot, from flank to flank. Its channel for the rail is the rail's own head in section (MIL-STD-1913's) from the rail's top down to the lower gauge line, and below that plain walls the rail's widest apart (how its jaws hook under a rail isn't in any view). The groove along its right side is cut 0.03 in deep (an assumption) between the heights the right profile gives; the raised strips along its top's two ends on the left, and the screws that hold it to the sight, aren't drawn. On its left the locking bar is the jaw in the bar's notch, a piece of its own and flush with the jaw, from the jaw's top line down; the bar's screw is a plain button head standing 0.04 in out of it (an assumption). Where the recoil stop lies under the mount isn't seen: the clamp is counted about the mount's middle, where the bar is.","The rail's top inside the mount is where the sheet's 39 mm puts it under the axis: the mount then reaches 0.40 in below the rail's top, as deep as the Micro T-2's LRP base and deeper than the catalog's other clamps."],"ledger":["aimpoint-duty-rds-39mm-mount.deck_above_rail","aimpoint-duty-rds-39mm-mount.mount_length","aimpoint-duty-rds-39mm-mount.clamp_below_rail","aimpoint-duty-rds.underside_above_clamp_bottom"]},"profiles":{},"gaps":[{"what":"A page that sells the mount alone, with its own figures","need":"Aimpoint's 39 mm torsion nut mount under a number of its own, with a weight: the weight here is what the maker's figures for the pair and the sight leave"},{"what":"The mount's own figures (its length, its height, where its recoil stop is)","need":"A drawing of the 39 mm one-piece mount, or Aimpoint's figure: the length is read off its left profile, the recoil stop's place isn't seen"}]},"aimpoint-duty-rds":{"id":"aimpoint-duty-rds","name":"Duty RDS Red Dot Sight","manufacturer":"Aimpoint","url":"https://bravocompanyusa.com/aimpoint-duty-rds-red-dot-sight-one-piece-torsion-nut-mount-39mm/","category":"optic","description":"Aimpoint's Duty RDS, a 1x red dot with a 2 MOA dot and an 18 mm clear aperture, screwed to its mount by the Micro footprint. Its axis is 1.03 in over its own base, 0.44 in higher than a Micro T-2's (T.REX ARMS: \"the optic sits roughly .40–.50 inches taller than a T-1/T-2 would sit on the same mount\"): on the mount it is sold on for an AR-15, \"Keyed Surface Mount: One-Piece Torsion Nut 39 mm Mount\" (Aimpoint's sheet, ITEM NO. 200759), that is 39 mm over the rail. Flip-up lens covers (\"SOLID FRONT / TRANSPARENT REAR\"), a push-button keypad on its left side, a CR2032 under the battery cap on its right, windage and elevation adjusters flush in the housing. The page linked is Bravo Company's: Aimpoint's own site isn't read.","weight":"aimpoint-duty-rds.sight_weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"footprint":{"origin":[0,0,0],"note":"Optic frame: origin on the sight's foot, the seam under it, at the footprint's middle, +x forward (D101). Along the sight it is the mount's middle in the pictures of the pair, the footprint's screws not being seen (aimpoint-duty-rds-39mm-mount.deck_x)."},"optical_axis":{"origin":[0,"{.axis_above_base}",0]}},"interfaces":{"footprint":{"type":"optic_footprint","role":"base","anchor":"footprint","params":{"pattern":"aimpoint_micro"},"flips":false,"note":"T.REX ARMS: \"The Duty RDS has the same footprint as the Aimpoint Micro T-1/Micro T-2 and is compatible with all Micro T-1/T-2 mounts.\"; Optics Trade: \"Mounting Standard Aimpoint Micro\" (data/interfaces.yaml, optic_footprint)."},"sight_line":{"type":"optic.sight_line","role":"sight","params":{"magnification":"1x"},"flips":false,"note":"Aimpoint's sheet: \"Optical Magnification: 1x\", \"Eye Relief: Unlimited\": a red dot, the eye anywhere behind it, so it has no eye point of its own. No page on file names a magnifier for it: T.REX ARMS calls it \"a solid choice for those wanting to add a magnifier\", and The Firearm Blog reviewed it behind Aimpoint's 3X-C; neither is a maker's or a seller's sentence that one fits."}},"materials":{"body":{"label":"Housing","finish":"anodized_matte","recolorable":false,"color":"aimpoint-dark-gray","options":{"black":{"label":"Black","finish":"anodized_matte","color":"aimpoint-dark-gray","sku":"200759","source":"https://bravocompanyusa.com/aimpoint-duty-rds-red-dot-sight-one-piece-torsion-nut-mount-39mm/"}},"default":"black","note":"The sight's housing. Aimpoint's sheet: \"PRESSURE FORGED ALUMINUM HOUSING The sight housing is constructed of non-reflective, hard-anodized aluminum\", \"Housing Anodized: Yes\"; the manual: \"High strength aluminum, black to dark gray, non-glare finish\"; Primary Arms: \"Color Black\", \"Finish Hardcoat Anodized\". 200759 is sold in this one colour on every page on file. In Aimpoint's own pictures the housing is the dark gray of the manual's sentence, a little lighter than the mount under it, as the Micro T-2's is: it takes that sight's colour (aimpoint-dark-gray, matched on Aimpoint's picture of the T-2). Not drawn: the lettering, the sculpted bevel down each flank."},"cap":{"label":"Battery cap","finish":"anodized_matte","recolorable":false,"color":"aimpoint-dark-gray","note":"The battery cap on the right side (the sheet: \"QUICK ACCESS BATTERY CAP\", \"Battery compartment mounted on the side for convenient access.\"): a smooth face with a coin slot, the housing's tone in Aimpoint's right profile and in Primary Arms' photographs. A piece of its own, standing out of the housing. Not drawn: the coin slot."},"buttons":{"label":"Push-button keypad","finish":"rubber","recolorable":false,"color":"placeholder-polymer-black","note":"The keypad on the left side (the sheet: \"DIGITAL INTENSITY BUTTONS Easy to use while wearing gloves.\"; the manual's \"1 Push-buttons\"): black in every picture, its two arrow buttons under a raised ring. What it is made of is on no page on file: drawn as black rubber, as it looks. Not drawn: the arrows and the ring's two dots."},"adjusters":{"label":"Windage and elevation adjusters","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"The windage adjuster on the right flank and the elevation adjuster on the top (the sheet: \"FLUSH-MOUNTED WINDAGE & ELEVATION ADJUSTMENTS\"): a bright steel disc with a Torx socket and two pin holes in each, in Aimpoint's right profile and quarter view and in Primary Arms' photographs. What they are made of is on no page on file: bright metal isn't fitted to a photo, the app's natural stainless. Not drawn: the Torx sockets, the pin holes, the 'R' arrow."},"covers":{"label":"Lens covers","finish":"rubber","recolorable":false,"color":"placeholder-polymer-black","note":"The sheet: \"Material Lens Cover: Thermoplastic Elastomer (TPE)\", \"SOLID FRONT / TRANSPARENT REAR FLIP-UP LENS COVERS\": the rear lid's clear pane is drawn in the lens slot's glass; the bright pins in the hinges aren't drawn."},"lens":{"label":"Lenses","finish":"glass","recolorable":false,"color":"glass-clear","note":"The two lenses and the rear lens cover's clear pane. The front lens is amber from ahead in every picture (its coating); not a colour of the glass here."}},"components":{},"geometry":{"model":"aimpoint-duty-rds.glb","components":{},"approximations":["Built from Aimpoint's own left profile of 200759 (the outline) and its right profile (where the battery cap, the windage adjuster and the groove along the mount are), at the scale the sheet's 67 mm of configuration height gives (checked by T.REX's photo of the sight beside a Micro T-2 on one rail, 1.0%; the sheet's 43 mm of sight reads 44.0 mm on it). No view from the front, the rear or above is on file, so everything across the sight is assumed: the housing's flanks are flat and upright, as far from the axis as the front cover ring's outside (0.66 in); its shoulders are quarter rounds of 0.2 in (an assumption) all along its top; the battery cap on the right and the keypad on the left each stand out of the flanks by what the sheet's 37 mm of width leaves (0.07 in), taken to be the same for both; the mount is as wide as the housing.","The housing is the outline from flank to flank: the sculpted bevel that runs down each flank from the top to the foot, and the waist under the tube, aren't drawn (the quarter views show them; no view gives their size). The lettering isn't drawn.","The battery cap and the keypad are plain discs (the cap's coin slot, the keypad's ring and its two arrow buttons aren't drawn); the windage adjuster is a steel disc a hundredth proud of the right flank (the sheet's \"FLUSH-MOUNTED\"), and the elevation adjuster the same disc on the top at the windage adjuster's station and of its size: no view from above is on file to place it (the quarter views have it on the top behind the middle).","The lens covers are drawn as photographed, raised: the front lid tilted back over the housing, the rear one standing, each a plain disc seen edge on in the side view (its diameter and thickness from that view), on its hinge, a block of the lug's outline in that view as wide as the flat of the housing's top (assumed); the rear lid's clear pane is cut through it and drawn as glass, as wide as the clear aperture it covers (assumed); the lids' ribs and tabs and the hinge pins aren't drawn. With the lids closed the sight is the sheet's 80 mm long; as drawn it is 78.7 mm over the cover rings.","The lenses are drawn at the two end faces at Aimpoint's 18 mm clear aperture: the real ones sit back inside the tube (the sheet: \"PROTECTED RECESSED LENS\")."],"ledger":["aimpoint-duty-rds.length","aimpoint-duty-rds.width","aimpoint-duty-rds.sight_height","aimpoint-duty-rds.axis_above_base","aimpoint-duty-rds.ring_span","aimpoint-duty-rds.window_d"]},"profiles":{"side":{"plane":"xy","origin":"the mount's middle (x over its rows, under the sight's foot), the mount's bottom; offset to the rail's top","offset":{"y":"clamp_bottom_y"},"points":[[-1.577,1.977],[-1.571,1.672],[-1.549,1.498],[-1.53,1.447],[-1.506,1.424],[-1.484,1.42],[-1.455,1.401],[-1.43,1.401],[-1.404,1.417],[-1.385,1.417],[-1.357,1.379],[-1.341,1.376],[-1.17,1.37],[-1.154,1.382],[-1.141,1.37],[-1.122,1.37],[-0.978,1.235],[-0.978,1.187],[-1.016,1.146],[-1.026,1.118],[-1.019,1.067],[-1.026,0.309],[-1.013,0.284],[-1.007,0.243],[-1.007,0.033],[-0.989,0.006],[-0.33,0.003],[-0.314,0.016],[0.314,0.016],[0.33,0.003],[0.615,0],[0.957,0],[0.984,0.024],[0.988,0.233],[0.997,0.281],[1.019,0.303],[1.022,0.334],[1.026,0.883],[1.003,0.943],[1.003,1.114],[0.973,1.148],[0.907,1.154],[0.886,1.181],[0.886,1.206],[0.919,1.246],[0.996,1.306],[1.03,1.275],[1.268,1.275],[1.292,1.292],[1.306,1.316],[1.325,1.316],[1.347,1.3],[1.37,1.297],[1.408,1.319],[1.436,1.325],[1.473,1.384],[1.492,1.466],[1.52,1.758],[1.52,2.094],[1.504,2.316],[1.469,2.484],[1.46,2.503],[1.43,2.53],[1.328,2.53],[1.322,2.536],[1.027,2.533],[1.005,2.53],[0.996,2.514],[0.97,2.514],[0.323,2.59],[0.184,2.584],[-0.006,2.559],[-0.124,2.552],[-0.187,2.571],[-0.304,2.622],[-0.897,2.638],[-0.954,2.638],[-0.989,2.628],[-0.999,2.638],[-1.148,2.486],[-1.512,2.438],[-1.539,2.389],[-1.558,2.287]],"features":{"front_cover_ring":[[[1.519,2.535],[1.068,2.535],[1.068,1.305],[1.519,1.305]]],"rear_cover_ring":[[[-1.167,2.497],[-1.576,2.497],[-1.576,1.324],[-1.167,1.324]]],"keypad":[[[0.774,1.679],[0.019,1.679],[0.019,0.927],[0.774,0.927]]],"keypad_button":[[[0.675,1.577],[0.117,1.577],[0.117,1.026],[0.675,1.026]]],"locking_bar":[[[0.418,0.503],[-0.438,0.503],[-0.438,0.014],[0.418,0.014]]],"lock_screw":[[[0.155,0.407],[-0.168,0.407],[-0.168,0.084],[0.155,0.084]]],"foot_seam":[[[1.021,0.911],[-1.024,0.911],[-1.024,0.899],[1.021,0.899]]],"jaw_top":[[[1.021,0.509],[-1.024,0.509],[-1.024,0.496],[1.021,0.496]]],"front_lid":[[[1.037,2.513],[-0.016,3.163],[0.041,3.492],[1.094,2.842]]],"rear_lid":[[[-1.008,2.636],[-1.221,2.833],[-0.764,3.705],[-0.548,3.521]]],"front_hinge":[[[1.433,2.535],[1.43,2.674],[1.385,2.763],[1.309,2.811],[1.202,2.792],[1.068,2.617],[1.037,2.516],[1.037,2.389],[1.433,2.389]]],"rear_hinge":[[[-1.135,2.494],[-1.183,2.662],[-1.246,2.741],[-1.373,2.738],[-1.443,2.662],[-1.5,2.547],[-1.515,2.446],[-1.515,2.357],[-1.135,2.357]]]},"scaleRefs":["aimpoint-duty-rds.height"],"inputs":{"aimpoint-duty-rds.height":2.637795275590551},"tolerance":0.005,"photo":"references/aimpoint-duty-rds 7e64620fc910 (Aimpoint's 200759_Aimpoint_DutyRDS_ProfileLeft as Bravo Company shows it (10987): the sight on its one-piece torsion nut mount, 39 mm, straight left side, white ground, covers raised)","method":"luminance < 235, 2 polygons excluded, closing ×2, largest piece, holes filled; scale from aimpoint-duty-rds.height = 2.6378 in (y-extent 832 px → 315.4 px/in); origin at x center, y min of the outline (x over 0.68–0.86 of the height from the top); Douglas-Peucker at 0.005 in with the extremes kept: 83 points (IoU 0.998 with the full outline); checks: centre between the top (max over 0.0 in windows) along x [-1.57, -1.53] 1.923 ± 0.010; width 3.098 ± 0.010; features through the same placement (front_cover_ring: the front lens cover's rubber ring round the tube's front end: its end to its seam with the housing, its top (under the hinge) to its bottom; rear_cover_ring: the rear lens cover's rubber ring round the tube's rear end, from its seam with the housing; keypad: the push-button keypad on the left flank under the axis: its raised outer ring, seen face on (a circle: its dark rim at rows 695 and about 930 down column 502, columns 383 and 621 along row 813); keypad_button: the keypad's button face inside the ring, with its two arrows (the dark circle at rows 726 and 900 down column 502, 174 px; along row 813 it reads 177 px, its middle a few px off the ring's, taken as centred in the ring); locking_bar: the mount's locking bar on its left side at its middle: a block in a notch of the jaw, flush with the jaw's face, from the jaw's top line to the mount's bottom; lock_screw: the locking bar's Torx T10 screw head, seen face on (a circle); foot_seam: the seam between the sight's foot and the mount's top: the dark line across at rows 936 to 940, over the mount's length; jaw_top: the line along the mount's left side where its jaw begins (the locking bar's top), row 1065; front_lid: the front lens cover's lid as photographed, raised: seen edge on, tilted back over the housing's top from its hinge. Four corners: its underside at the hinge end and at its tip, its top at the tip and at the hinge end (the underside's line through its lower edge at columns 315 to 600, the top's through columns 330 to 600); rear_lid: the rear lens cover's lid as photographed, raised: seen edge on, standing behind the rear hump, leaning back. Four corners: its front face at its foot and its top, its rear face at its top and its foot (the faces' lines through columns 805 to 940); front_hinge: the front cover's hinge lug on top of its ring, as photographed with the lid raised (carried down into the ring below row 424); rear_hinge: the rear cover's hinge lug on top of its ring, with the lid raised (carried down into the ring below row 440)) (tools/trace.py)","via":"harvest","note":"The raised lens covers' lids and hinges are cut out of it (the lids aren't the sight's outline; their rings round the tube's two ends are). The lettering, the keypad, the seam under the sight's foot, the jaw's line and the locking bar with its screw are inside the silhouette: they are features, and so are the cover rings' seams, the two raised lids and their hinges."}},"gaps":[{"what":"A straight view from the front, the rear or above","need":"A studio end view or top view on a plain ground: the housing's width and section, how far the battery cap and the keypad stand out, the mount's width and its channel, where the elevation adjuster is along the top"},{"what":"What the 43 mm of sight height spans","need":"A page or a picture that shows the sight's underside off its mount: the profile reads 44.0 mm from the seam under its foot to its top at the scale of the 67 mm"},{"what":"Aimpoint's own pages (aimpoint.com, aimpoint.us)","need":"They refuse the project's reader and are left alone; a page the user saves from their own browser could be filed"},{"what":"A magnifier for it","need":"A maker's or a seller's sentence that a magnifier (Aimpoint's 3XMag-1 or 3X-C) goes behind the Duty RDS: none on file"}]},"aimpoint-micro-lrp-39mm":{"id":"aimpoint-micro-lrp-39mm","name":"LRP (Lever Release Picatinny) Mount with 39 mm Spacer, for Micro","manufacturer":"Aimpoint","url":"https://bravocompanyusa.com/micro-t-2-2-moa-red-dot-reflex-sight-with-39-mm-spacer-lrp-mount/","category":"optic_mount","description":"The mount and spacer Aimpoint sells the Micro T-2 on for an AR-15: \"This AR15 Ready version includes 39 mm Spacer and LRP (Lever Release Picatinny) Mount\" (Aimpoint's sheet, ITEM NO. 200198). A Micro-footprint dot screws to the spacer's top; a T-2 on it has its axis 39 mm over the rail (\"Sight, mount and high spacer – 39 mm ... measured from top surface of Picatinny/Weaver rail\"), a lower 1/3 co-witness. The base clamps to the rail by a lever: Bravo Company, \"a 39mm spacer and LRP (Lever Release Picatinny) base that attaches to MIL-STD-1913 rails with a quick detach mechanism\". The page linked is Bravo Company's for the pair: no page on file sells the mount alone.","weight":"aimpoint-micro-lrp-39mm.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":[0,0,0],"note":"Mount frame: origin on the rail's top at the middle of the LRP base, +x forward. The base's cross bolt (the socket in its right wall) is at its middle within 0.02 in, 0.04 in under the rail's top by the sheet's 39 mm: in one of the rail's grooves."},"deck":{"origin":["{.deck_x}","{.deck_above_rail}",0],"note":"On the spacer's top at the footprint's middle: where a Micro dot's base is put (D101)."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":"={.mount_length} / 2","clamp_front":"={.mount_length} / 2"},"flips":false,"note":"The LRP base's length about its middle (the frame's origin)."},"deck":{"type":"optic_footprint","role":"deck","anchor":"deck","params":{"pattern":"aimpoint_micro"},"flips":false,"note":"The spacer's top is cut for the Micro footprint: Aimpoint sells it under the Micro T-2, and Primary Arms says of that sight \"Compatible with Aimpoint Micro T-1/T-2/H-1 style mounts.\" (data/interfaces.yaml, optic_footprint)."}},"materials":{"mount":{"label":"Spacer and LRP mount","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","note":"The 39 mm spacer and the LRP base, with the lever's hexagonal nut on its left side: black (the manual's sentence for the sight and mount; #2e2d31 and #2f2e32 on Aimpoint's two profiles, #262626 and #303030 in Atlantic Tactical's photographs). The nut is a dark steel in Aimpoint's picture and black in the seller's: drawn with the base."},"hardware":{"label":"LRP lever","finish":"anodized_matte","recolorable":false,"color":"aimpoint-lrp-lever","note":"The lever along the base's left side: a pale, warm, matte metal in every picture of 200198, against the black base (#dac9b9 on Aimpoint's left profile, #cfbfae on its quarter view; #c1baa2 in Atlantic Tactical's photograph of one). What it is made of and how it is finished is on no page on file: its colour is matched to Aimpoint's picture, and it is drawn matte, as it looks (no bright line anywhere on it), in the finish type the rest of the mount has. It was bare stainless, a stand-in, until 2026-10-06."}},"components":{},"geometry":{"model":"aimpoint-micro-lrp-39mm.glb","components":{},"approximations":["Built with the sight from Aimpoint's own left profile of 200198 (the pair's outline) and its right profile (where the base's socket is): no view from the front, the rear or above is on file, so the spacer and the base are taken to be as wide as the sight's housing.","The spacer is a plain block: the hollows along its two sides (lines in the side view) aren't cut, since how deep they are isn't read. The LRP base's channel for the rail is the rail's own head in section (MIL-STD-1913's, since 2026-10-12) from the rail's top down to the lower gauge line 0.154 in under it, and below that plain walls the rail's width apart (how its jaws hook under a rail isn't in any view); its lever is a bar standing off the left wall, half as thick as it is high, with its grip behind and its hexagonal nut at the front; the grip's ribs, the lever's pivot and cam, and the screw heads on the base aren't drawn. The socket in the right wall is a round recess half as deep as it is wide.","The rail's top inside the LRP base is where the sheet's 39 mm puts it under the axis: the base then reaches 0.39 in below the rail's top, deeper than the catalog's other clamps."],"ledger":["aimpoint-micro-lrp-39mm.deck_above_rail","aimpoint-micro-lrp-39mm.mount_length","aimpoint-micro-lrp-39mm.clamp_below_rail","aimpoint-micro-t-2.spacer_length","aimpoint-micro-t-2.base_top_above_clamp_bottom"]},"profiles":{},"gaps":[{"what":"A page that sells the mount alone, with its own figures","need":"Aimpoint's LRP mount and 39 mm spacer under a number of their own, with a weight: the weight here is the pair's floor less the sight's"},{"what":"The LRP mount's own height over the rail","need":"Aimpoint's figure for the LRP mount without a spacer, or a view of 200198 on a rail: the rail's top is placed by the 39 mm alone"},{"what":"What the LRP's lever is made of and how it is finished","need":"A page that names it: its pale colour is matched to a seller's photograph of one (Aimpoint's own pictures have it lighter than a matte surface can be under the app's light), and it is drawn matte because it looks it"}]},"aimpoint-micro-t-2":{"id":"aimpoint-micro-t-2","name":"Micro T-2 Red Dot Reflex Sight","manufacturer":"Aimpoint","sku":"200180","url":"https://bravocompanyusa.com/aimpoint-micro-t-2-red-dot-reflex-sight---no-mount/","category":"optic","description":"Aimpoint's Micro T-2, a 1x red dot with a 2 MOA dot and an 18 mm clear aperture, screwed to its mount by the Micro footprint (Primary Arms: \"Compatible with Aimpoint Micro T-1/T-2/H-1 style mounts.\"). Its axis is 0.59 in over its own base: on the LRP mount with the 39 mm spacer it is sold on for an AR-15 (200198, \"AR15 Ready\") that is the sheet's 39 mm over the rail. Flip-up lens covers front and rear, a CR2032 under the intensity switch on its right side. The page linked is Bravo Company's for the sight alone: Aimpoint's own site isn't read.","weight":"aimpoint-micro-t-2.sight_weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"footprint":{"origin":[0,0,0],"note":"Optic frame: origin on the sight's flat underside at the footprint's middle, +x forward: where a Micro mount's deck is (D101). Along the sight it is the middle of the 39 mm spacer it is pictured on, the footprint's screws not being seen (aimpoint-micro-lrp-39mm.deck_x)."},"optical_axis":{"origin":[0,"{.axis_above_base}",0]}},"interfaces":{"footprint":{"type":"optic_footprint","role":"base","anchor":"footprint","params":{"pattern":"aimpoint_micro"},"flips":false,"note":"Primary Arms, of the T-2 (200170): \"Compatible with Aimpoint Micro T-1/T-2/H-1 style mounts.\" (data/interfaces.yaml, optic_footprint)."},"sight_line":{"type":"optic.sight_line","role":"sight","params":{"magnification":"1x"},"flips":false,"note":"Aimpoint's sheet: \"Optical Magnification: 1x\", \"Eye Relief: Unlimited\": a red dot, the eye anywhere behind it, so it has no eye point of its own. \"Compatible with Aimpoint 3x and 6x magnifiers\"."}},"materials":{"body":{"label":"Housing","finish":"anodized_matte","recolorable":false,"color":"aimpoint-dark-gray","options":{"black":{"label":"Black","finish":"anodized_matte","color":"aimpoint-dark-gray","sku":"200180","source":"https://bravocompanyusa.com/aimpoint-micro-t-2-red-dot-reflex-sight---no-mount/"}},"default":"black","note":"The sight's housing. The manual: \"Sight and mount: High strength aluminum, hard anodized, black to dark gray, non-glare finish\"; Bravo Company: \"The sight housing is constructed of hard-anodized aluminum alloy\", \"Hard anodized non-reflective surface\". In Aimpoint's own pictures of 200198 and in Atlantic Tactical's photographs of one the housing is the dark gray of that sentence, lighter than the mount under it and than its own knobs (#3b383b against the spacer's #2e2d31 on Aimpoint's left profile, both flats square to the lens; #393836 against #262626 in the seller's): a colour of its own, matched. 200198 is sold in this one colour on every page on file. Aimpoint's Flat Dark Earth T-2 is the sight alone, with no mount, under another number (Primary Arms: \"SKU: 200804 MPN: 200804\", \"Special edition Cerakote FDE T-Series finish\"): a sibling, not a colour of this part. Not drawn: the lettering."},"knobs":{"label":"Intensity switch and turret caps","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","note":"The intensity switch, the windage cap and the elevation turret: black, and blacker than the housing they stand in, in Aimpoint's right profile (#222223 against #4f4d4e) and the seller's photograph of that side (#343434 against #4c4b48). Taken to be anodized as the housing is (no page says). Not drawn: the bright ring at the elevation turret's foot, the white INTENSITY scale."},"covers":{"label":"Lens covers","finish":"rubber","recolorable":false,"color":"placeholder-polymer-black","note":"The sheet: \"Material Lens Cover: Thermoplastic Elastomer (TPE)\"; the manual: \"black, non-glare finish\". Bravo Company: \"Flip-up lens covers – front is solid, and rear is transparent\": the rear lid's clear pane isn't drawn, nor the two bright hinge pins."},"lens":{"label":"Lenses","finish":"glass","recolorable":false,"color":"glass-clear","note":"The front lens is amber from ahead in every picture (its coating); not a colour of the glass here."}},"components":{},"geometry":{"model":"aimpoint-micro-t-2.glb","components":{},"approximations":["Built from Aimpoint's own left profile of 200198 (the outline) and its right profile (where the intensity switch, the windage cap and the base's socket are), at the scale the sheet's 47 mm gives on the standard-mount photo. No view from the front, the rear or above is on file, so everything across the sight is assumed: the housing's flanks are flat and upright, as far from the axis as its flat underside is (0.59 in); its shoulders are quarter rounds of 0.26 in, which is how far under the top the shading down its left flank says the flat stops, taken to be as wide as they are high; the turret housing is as wide as the rest of the top; the spacer and the LRP base are as wide as the housing.","Sideways it is placed by the maker's 41 mm, taken from the left flank to the face of the intensity switch; the windage cap is drawn standing half as far out of the right flank as the switch (its own reach isn't read). The switch and the caps are plain cylinders: the knurl, the switch's coin slot and numbers, the caps' two pins aren't drawn.","The lens covers are drawn as photographed, raised: the front lid tilted open over the housing, the rear one upright, each a plain disc seen edge on in the side view (its diameter and thickness from that view), on its hinge, a block of the lug's outline in that view as wide as the flat of the housing's top (assumed); the lids' ribs and tabs, the hinge pins and the rear lid's clear pane aren't drawn. With the lids closed the sight is the maker's 79 mm long; as drawn it is 72.5 mm over the cover rings.","The lenses are drawn at the two end faces at Aimpoint's 18 mm clear aperture: the real ones sit back inside the tube, the front one tilted (the manual: \"The optical system is designed for the front lens to be mounted this way\")."],"ledger":["aimpoint-micro-t-2.length","aimpoint-micro-t-2.width","aimpoint-micro-t-2.sight_height","aimpoint-micro-t-2.axis_above_base","aimpoint-micro-t-2.ring_span","aimpoint-micro-t-2.window_d","aimpoint-micro-t-2.shoulder_radius"]},"profiles":{"side":{"plane":"xy","origin":"the spacer block's middle (x over its rows), the LRP mount's bottom; offset to the rail's top","offset":{"y":"clamp_bottom_y"},"points":[[-1.399,2.058],[-1.394,1.706],[-1.378,1.563],[-1.355,1.484],[-1.339,1.465],[-1.313,1.462],[-1.283,1.442],[-1.219,1.46],[-1.188,1.419],[-1.02,1.414],[-1.004,1.422],[-0.979,1.409],[-0.965,1.387],[-0.96,1.311],[-0.957,0.601],[-0.98,0.581],[-1.006,0.527],[-1.008,0.392],[-1.015,0.385],[-1.045,0.385],[-1.277,0.398],[-1.336,0.383],[-1.353,0.356],[-1.35,0.063],[-1.321,0.048],[-1.295,0.051],[-1.198,0.11],[-1.145,0.105],[-1.03,0.11],[-1.023,0.103],[-1.018,0.032],[-1.004,0.018],[-0.961,0.003],[-0.264,0],[-0.001,0],[0.198,0.003],[0.318,0.02],[0.992,0.015],[1.023,0.029],[1.029,0.119],[1.016,0.175],[1.092,0.315],[1.097,0.341],[1.023,0.463],[1.018,0.502],[0.988,0.573],[0.955,0.596],[0.962,0.767],[0.965,1.359],[0.974,1.371],[0.99,1.331],[1.007,1.317],[1.229,1.32],[1.251,1.336],[1.265,1.36],[1.283,1.36],[1.311,1.342],[1.331,1.342],[1.359,1.363],[1.382,1.365],[1.414,1.408],[1.437,1.515],[1.457,1.841],[1.452,2.158],[1.437,2.344],[1.411,2.457],[1.396,2.487],[1.374,2.504],[1.27,2.504],[1.247,2.522],[1.226,2.522],[1.219,2.555],[0.963,2.555],[0.962,2.508],[0.98,2.497],[0.978,2.477],[0.966,2.468],[0.195,2.537],[0.101,2.552],[0.034,2.58],[-0.162,2.733],[-0.287,2.733],[-0.318,2.716],[-0.359,2.726],[-0.456,2.728],[-0.47,2.722],[-0.479,2.703],[-0.542,2.703],[-0.56,2.728],[-0.657,2.728],[-0.703,2.718],[-0.718,2.728],[-0.731,2.723],[-0.749,2.736],[-0.859,2.739],[-1.002,2.46],[-1.226,2.46],[-1.225,2.431],[-1.231,2.425],[-1.321,2.425],[-1.35,2.406],[-1.365,2.375],[-1.383,2.283]],"features":{"elevation_turret":[[[-0.336,2.712],[-0.706,2.712],[-0.706,2.49],[-0.336,2.49]]],"turret_recess":[[[-0.328,2.719],[-0.724,2.719],[-0.724,2.49],[-0.328,2.49]]],"lever_bar":[[[0.558,0.364],[-0.872,0.364],[-0.872,0.149],[0.558,0.149]]],"lever_grip":[[[-0.846,0.371],[-1.351,0.371],[-1.351,0.06],[-0.846,0.06]]],"lever_nut":[[[1.086,0.453],[0.838,0.453],[0.838,0.162],[1.086,0.162]]],"front_cover_ring":[[[1.456,2.556],[0.992,2.556],[0.992,1.318],[1.456,1.318]]],"rear_cover_ring":[[[-1.038,2.462],[-1.397,2.462],[-1.397,1.415],[-1.038,1.415]]],"front_lid":[[[0.941,2.487],[-0.019,3.12],[0.144,3.37],[1.104,2.737]]],"rear_lid":[[[-0.831,2.732],[-1.124,2.732],[-0.989,3.712],[-0.695,3.712]]],"front_hinge":[[[1.374,2.564],[1.38,2.605],[1.385,2.653],[1.349,2.704],[1.293,2.755],[1.201,2.776],[1.127,2.758],[1.094,2.727],[0.981,2.556],[0.981,2.4],[1.221,2.4],[1.221,2.556]]],"rear_hinge":[[[-0.872,2.727],[-1.124,2.727],[-1.157,2.691],[-1.254,2.681],[-1.3,2.64],[-1.334,2.574],[-1.326,2.528],[-1.288,2.492],[-1.244,2.462],[-1.244,2.311],[-1.038,2.311],[-0.999,2.462],[-0.928,2.605]]]},"scaleRefs":["aimpoint-micro-t-2.ring_span"],"inputs":{"aimpoint-micro-t-2.ring_span":2.856},"tolerance":0.005,"photo":"references/aimpoint-micro-t-2 10c377094e97 (Aimpoint's 200198_Micro_T-2_AR15_Ready_Profile_Left as Bravo Company shows it (10970): the sight on the 39 mm spacer and the LRP mount, straight left side, transparent ground, covers raised)","method":"alpha > 0.5, 2 polygons excluded, closing ×2, largest piece, holes filled; scale from aimpoint-micro-t-2.ring_span = 2.856 in (x-extent 1119 px → 391.8 px/in); origin at x center, y min of the outline (x over 0.56–0.74 of the height from the top); Douglas-Peucker at 0.005 in with the extremes kept: 103 points (IoU 0.997 with the full outline); checks: centre between the top (max over 0.0 in windows) along x [-1.385, -1.35] 1.941 ± 0.022; features through the same placement (elevation_turret: the knurled elevation turret standing in its recess in the housing's top, down to the bright ring at its foot; turret_recess: the opening across the housing's top that the turret stands in, between the housing's front and rear walls; lever_bar: the LRP's lever (pale metal) along the base's left side: its bar, from its rounded front end; lever_grip: the lever's grip at its rear end, with three ribs, hooked down at its tip; lever_nut: the hexagonal nut on the base's left side at its front (the lever's adjustment), seen face on; front_cover_ring: the front lens cover's rubber ring round the tube's front end: its end to the seam with the housing behind it, its top (under the hinge, by its radius below the axis) to its bottom; rear_cover_ring: the rear lens cover's rubber ring round the tube's rear end, from its seam with the housing; front_lid: the front lens cover's lid as photographed, raised: seen edge on, tilted open over the housing's sloped top. Four corners: its underside at the hinge end and at its tip, its top at the tip and at the hinge end (the underside's line through its edge at columns 463 to 813, the top's parallel to it through columns 438 to 688); rear_lid: the rear lens cover's lid as photographed, raised: seen edge on, standing nearly upright behind the turret housing, leaning forward. Four corners: its front and rear faces where it meets its hinge, and at its top (the faces' lines through rows 141 to 421); front_hinge: the front cover's hinge on top of its ring, as photographed with the lid raised: its lug's outline from the ring's top round to the lid's hinge end (the rows below 519 are inside the ring: the block is carried down into it so it stands on the round ring); rear_hinge: the rear cover's hinge behind the turret housing, as photographed with the lid raised: from the housing's rear slope and the lid's foot round its lug to the ring's top (carried down into the ring below row 556)) (tools/trace.py)","via":"harvest","note":"The raised lens covers' lids and hinges are cut out of it (the lids aren't the sight's outline; their rings round the tube's two ends are). The lettering, the turret in its recess, the spacer's grooves and the lever are inside the silhouette: the turret, its recess, the lever and its nut are features, and so are the cover rings' seams, the two raised lids and their hinges."}},"gaps":[{"what":"A straight view from the front, the rear or above","need":"A studio end view or top view on a plain ground: the housing's width and section, the turret housing's width, how far the switch and the windage cap stand out, the spacer's waist, the LRP base's width with its lever"},{"what":"Aimpoint's own pages (aimpoint.com, aimpoint.us)","need":"They refuse the project's reader and are left alone; a page the user saves from their own browser could be filed"}]},"aimpoint-pro":{"id":"aimpoint-pro","name":"Patrol Rifle Optic (PRO) Red Dot Reflex Sight - QRP2 Mount","manufacturer":"Aimpoint","sku":"12841","url":"https://bravocompanyusa.com/aimpoint-pro-patrol-rifle-optic/","category":"optic","description":"Aimpoint's Patrol Rifle Optic, a 1x red dot with a 2 MOA dot and a 23 mm clear aperture on a 30 mm tube, in its ring on the QRP2 mount with the spacer an AR-15 takes it on: \"ARTICLE NUMBERS Aimpoint® PRO 12841\" (Aimpoint's 2011 sheet); the 2021 manual: \"Configuration (spacer) 39 mm / 1.5 in (from top surface of Picatinny rail)\"; Primary Arms: \"Included mount provides absolute co-witness with AR-15 sights\". Flip-up lens covers, the rear one clear; a DL1/3N battery in the housing along its right shoulder. The page linked is Bravo Company's: Aimpoint's own site isn't read.","weight":"aimpoint-pro.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":[0,0,0],"note":"Optic frame: origin on the rail's top at the middle of the QRP2's length, +x forward. The torque knob on the mount's left side is centred there within 0.02 in (Aimpoint's left profile); the manual's recoil stop, which goes \"in the selected groove of the Picatinny rail\", isn't seen in any view."},"optical_axis":{"origin":[0,"{.optical_axis_above_rail}",0]}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":"={.mount_length} / 2","clamp_front":"={.mount_length} / 2"},"flips":false,"note":"The QRP2's length about its middle (the frame's origin). The 2021 manual: \"Install the sight with the recoil stop in the selected groove of the Picatinny rail. d Push the sight forward (toward muzzle) and tighten the torque knob (13) until the third snap. This ensures that the mount is secured and the recoil stop is in contact with the side of the groove of the Picatinny rail.\" (The 2018 edition: \"until it snaps twice\"; the 2011 sheet: \"Snap knob three times for a perfect mount.\")"},"sight_line":{"type":"optic.sight_line","role":"sight","params":{"magnification":"1x"},"flips":false,"note":"The manual: \"Optical magnification 1X\", \"Eye relief Unlimited\": a red dot, the eye anywhere behind it, so it has no eye point of its own. Bravo Company: \"The PRO sight is fully compatible with all generations of night vision devices and the Aimpoint 3XMag-1™ and 3X-C™ magnifiers.\"; the 2011 sheet: \"may be used with Aimpoint® 3X Magnifier (3XMag)\"."}},"materials":{"body":{"label":"Housing","finish":"anodized_matte","recolorable":false,"color":"aimpoint-dark-gray","options":{"black":{"label":"Black","finish":"anodized_matte","color":"aimpoint-dark-gray","sku":"12841","source":"https://bravocompanyusa.com/aimpoint-pro-patrol-rifle-optic/"}},"default":"black","note":"The sight's housing: the objective bell, the tube, the main body and the battery housing on its right shoulder. The manual: \"Sight Hard anodized, high strength aluminum, black to dark gray, non-glare finish\"; City Arsenal: \"Color/Finish Black/Anodized, Semi-Matte\". In Aimpoint's own profiles the housing is the dark gray of that sentence, the knobs and caps blacker: Aimpoint's dark gray as matched on the Micro T-2's housing (aimpoint-dark-gray). 12841 is sold in this one colour on every page on file. Not drawn: the lettering (\"Aimpoint\", \"Patrol Rifle Optic\", the serial)."},"knobs":{"label":"Caps, rotary switch and torque knob","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","note":"The battery cap and the rotary switch's knurled ring at the two ends of the battery housing, the elevation and windage caps, and the QRP2's torque knob: black, blacker than the housing in Aimpoint's profiles. Taken to be anodized as the housing is (no page says). Not drawn: the knurl, the caps' cross slots, their straps."},"mount":{"label":"Ring, spacer and QRP2 mount","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","note":"The 30 mm ring (Base & Top Ring), the spacer and the QRP2 mount: black (the manual's sentence is the sight's; the 2011 sheet: \"Surface finish Hard anodized\"). The ring's four screws are drawn with it. Not drawn: the recoil stop, the oblong on the QRP2's right side."},"covers":{"label":"Lens covers","finish":"rubber","recolorable":false,"color":"placeholder-polymer-black","note":"The manual: \"Lens covers Thermoplastic elastomer, black, non-glare finish\". Bravo Company: \"Flip-up lens covers – front is solid, and rear is transparent\": the rear lid is a rubber rim round a clear pane, which is drawn in the glass of the lenses. Not drawn: the hinge pins."},"lens":{"label":"Lenses","finish":"glass","recolorable":false,"color":"glass-clear","note":"The front lens is amber from ahead in every picture (its coating); not a colour of the glass here."}},"components":{},"geometry":{"model":"aimpoint-pro.glb","components":{},"approximations":["Built from Aimpoint's own left profile of 12841 (the outline), at the scale Primary Arms' photograph with both covers closed gives: the manual's 136 mm, the configuration's length, between the closed lids, sets it, and the QRP2's length read there scales Aimpoint's profile. At that scale the length over the raised covers' rings is 130.6 mm (the 2011 sheet's 130 mm) and the jaws stand 47.5 mm under the axis in Aimpoint's profile and 47.3 in Primary Arms' photograph. No view square from the front, the rear or above is on file (Primary Arms' photograph from ahead and to the right shows the QRP2's front end face, and Optics Trade's of the sight upside down and of the QRP2 alone show its underside, all oblique), so what is across the sight is placed by the maker's widths or assumed: the bell, the cover rings, the main body and its rear end are round about the axis (the quarter views show them round), each at the depth of its own lower edge in the profile.","The battery housing is a round tube along the right shoulder, as wide as its cap reads in the right profile, its top at the outline's top and its right side where the manual's 49 mm of sight width puts it from the body's left flank, joined to the body by a web; the rotary switch and the battery cap are knurled rings drawn as plain cylinders at its two ends. The elevation cap stands on the top's middle; the windage cap stands out of the right side under the battery housing, where the right profile has it, its face at the sight's right side. The caps' straps and slots aren't drawn.","The ring is the 30 mm tube's ring: round over the tube, the top ring's flats and the base's flats each side a little more than a screw head past the round (ring_ear_reach, assumed), the split open between them where the left profile has it, and two screws down through each pair of flats, their heads standing on the top ring's flats as the left profile has the near two (the far two assumed the same); the screws' hex sockets aren't cut. The ring base's foot, the spacer and the QRP2's left side are blocks of the mount's assumed half width (0.55 in: no page gives it and no view squarely shows it), the spacer's eight holes cut through as Aimpoint's profile has them. The QRP2's right (fixed) jaw stands out further, 0.59 in from the rail's middle: Aimpoint's 55 mm for the QRP2 alone (its knob's face to that jaw, as Kenzie's Optics gives the table) is 15 mm less than its 70 mm for the configuration (the same knob's face to the sight's right side), and Primary Arms' photograph from ahead and to the right has the QRP2's top showing as a strip beyond the spacer's right face.","The QRP2's channel for the rail is the rail's own head in section (MIL-STD-1913's, lib.rail_seat) from the rail's top down to the lower gauge line; its right jaw is deep all along, to where the right profile has its lowest edge under the spacer's holes (0.316 in under the rail's top), and the left side hooks under the rail only at the movable jaw, the block the torque knob stands in (0.337 in under it, the left profile's): ahead of and behind it the left side is the body's own lower edge, 0.06 in under the rail's top, as Primary Arms' photograph has the front end face and Optics Trade's has the QRP2 alone from its channel side (the left profile's strip under that side, drawn as a lip to the lower gauge line until the detail pass of 2026-10-19, is the far jaw seen from about 9 degrees above). Its edges are left unbroken (the break rounded the movable jaw's face off the rail's head at its ends). The torque knob is a cylinder out of that block, face on at the mount's middle, its face where the manual's 70 mm of width puts it; the recoil stop, the oblong on the right side and the jaws' hooks under the rail aren't in any view and aren't drawn.","The lens covers are drawn as photographed, raised: the front lid tilted open over the bell, the rear one leaning forward over the battery housing, each a plain disc as long as its outline in the side view and of an assumed thickness (lid_thickness), the rear one a rim round a clear pane as wide as the clear aperture (assumed), on its hinge, a block of the lug's outline in that view as wide as the cover ring's top (assumed). With the lids closed the sight is the maker's 136 mm long; as drawn it is 130.6 mm over the cover rings.","The lenses are drawn at the two end faces at Aimpoint's 23 mm clear aperture: the real ones sit back inside the tube (the 2011 sheet: \"Both the front and rear lenses are recessed within the sight body\").","The rail's top inside the QRP2 is where the manual's 39 mm puts it under the axis."],"ledger":["aimpoint-pro.length","aimpoint-pro.width","aimpoint-pro.height","aimpoint-pro.optical_axis_above_rail","aimpoint-pro.ring_span","aimpoint-pro.mount_length","aimpoint-pro.window_d","aimpoint-pro.tube_od"]},"profiles":{"side":{"plane":"xy","origin":"the QRP2's middle (x over its rows), the torque knob's lowest edge; offset to the rail's top","offset":{"y":"knob_bottom_y"},"points":[[-2.1,2.43],[-2.1,2.152],[-2.083,1.867],[-2.068,1.781],[-2.033,1.681],[-2.017,1.665],[-1.995,1.662],[-1.956,1.637],[-1.931,1.637],[-1.917,1.651],[-1.895,1.655],[-1.86,1.608],[-1.831,1.598],[-1.681,1.587],[-1.631,1.587],[-1.578,1.598],[-1.421,1.551],[-1.289,1.551],[-1.273,1.528],[-1.289,1.516],[-1.321,1.516],[-1.337,1.503],[-1.387,1.432],[-1.394,1.403],[-1.387,1.336],[-1.391,1.25],[-1.384,1.236],[-1.384,1.057],[-1.391,1.022],[-1.391,0.986],[-1.384,0.975],[-1.387,0.704],[-1.371,0.688],[-1.339,0.688],[-1.33,0.679],[-1.337,0.597],[-1.325,0.585],[-1.232,0.585],[-0.608,0.599],[-0.599,0.59],[-0.592,0.415],[-0.587,0.41],[-0.462,0.41],[-0.453,0.401],[-0.442,0.348],[-0.41,0.28],[-0.407,0.251],[-0.378,0.223],[-0.337,0.157],[-0.266,0.093],[-0.209,0.068],[-0.184,0.046],[-0.073,0.011],[-0.002,0.004],[0.009,0],[0.087,0.007],[0.173,0.029],[0.262,0.071],[0.326,0.121],[0.374,0.169],[0.424,0.237],[0.471,0.351],[0.474,0.398],[0.487,0.41],[0.594,0.41],[0.61,0.419],[0.613,0.579],[0.622,0.588],[1.229,0.592],[1.311,0.596],[1.319,0.604],[1.316,0.686],[1.325,0.695],[1.378,0.699],[1.387,0.744],[1.377,1.243],[1.384,1.257],[1.394,1.664],[1.398,1.689],[1.407,1.697],[1.45,1.69],[1.724,1.541],[2.092,1.541],[2.118,1.5],[2.195,1.434],[2.723,1.444],[2.776,1.494],[2.83,1.487],[2.901,1.519],[2.938,1.564],[2.963,1.617],[2.996,1.738],[3.021,1.895],[3.042,2.223],[3.031,2.569],[2.999,2.808],[2.967,2.937],[2.931,3.004],[2.905,3.038],[2.109,3.042],[2.092,3.021],[1.742,3.024],[1.692,3.01],[1.5,2.903],[1.457,2.899],[1.4,2.899],[1.391,2.908],[1.377,2.969],[1.364,2.978],[1.325,2.981],[0.451,2.981],[0.442,2.99],[0.442,3.261],[0.432,3.35],[0.417,3.39],[0.39,3.416],[0.362,3.423],[0.219,3.423],[0.205,3.388],[0.177,3.391],[0.162,3.406],[-0.947,3.409],[-0.954,3.423],[-1.328,3.416],[-1.33,2.919],[-1.339,2.91],[-2.02,2.91],[-2.047,2.873],[-2.072,2.776],[-2.09,2.623]],"features":{"front_ring":[[[3.037,3.04],[2.127,3.04],[2.127,1.435],[3.037,1.435]]],"bell":[[[2.127,3.012],[1.385,3.012],[1.385,1.471],[2.127,1.471]]],"ring":[[[1.385,2.983],[0.216,2.983],[0.216,1.492],[1.385,1.492]]],"ring_split":[[[1.385,2.398],[0.216,2.398],[0.216,2.22],[1.385,2.22]]],"ring_ears":[[[1.385,2.484],[0.216,2.484],[0.216,2.398],[1.385,2.398]]],"ring_screws":[[[1.253,2.634],[1.04,2.634],[1.04,2.477],[1.253,2.477]],[[0.647,2.634],[0.433,2.634],[0.433,2.477],[0.647,2.477]]],"body":[[[0.216,3.012],[-1.375,3.012],[-1.375,1.514],[0.216,1.514]]],"battery":[[[0.612,3.422],[-1.671,3.422],[-1.671,3.004],[0.612,3.004]]],"battery_cap":[[[0.612,3.422],[0.373,3.422],[0.373,3.004],[0.612,3.004]]],"elevation_cap":[[[-0.173,3.368],[-0.94,3.368],[-0.94,3.09],[-0.173,3.09]]],"rear_ring":[[[-1.671,2.912],[-2.099,2.912],[-2.099,1.557],[-1.671,1.557]]],"foot":[[[1.385,1.496],[-1.389,1.496],[-1.389,1.321],[1.385,1.321]]],"spacer":[[[1.385,1.321],[-1.389,1.321],[-1.389,0.979],[1.385,0.979]]],"holes":[[[1.043,1.236],[-0.683,1.236],[-0.683,1.079],[1.043,1.079]]],"qrp2":[[[1.385,0.979],[-1.389,0.979],[-1.389,0.686],[1.385,0.686]]],"lip":[[[1.314,0.686],[-1.332,0.686],[-1.332,0.59],[1.314,0.59]]],"jaw":[[[0.612,0.686],[-0.601,0.686],[-0.601,0.408],[0.612,0.408]]],"knob":[[[0.487,0.95],[-0.458,0.95],[-0.458,0.002],[0.487,0.002]]],"front_lid":[[[2.395,3.029],[0.79,3.867],[0.95,4.099],[2.555,3.261]]],"rear_lid":[[[-1.1,3.361],[-1.35,3.411],[-0.637,4.349],[-0.369,4.231]]],"front_hinge":[[[2.93,3.029],[2.905,3.243],[2.769,3.397],[2.573,3.404],[2.43,3.34],[2.27,3.101],[2.27,3.029]]],"rear_hinge":[[[-1.332,2.905],[-1.332,3.397],[-1.564,3.397],[-1.742,3.29],[-1.849,3.101],[-1.831,2.905]]]},"scaleRefs":["aimpoint-pro.mount_length"],"inputs":{"aimpoint-pro.mount_length":2.771},"tolerance":0.005,"photo":"references/aimpoint-pro 15e90d27e3d6 (Aimpoint's 12841_PRO_Profile_Left as City Arsenal hosts it: straight left side, transparent ground, both covers raised)","method":"alpha > 0.5, 2 polygons excluded, closing ×2, largest piece, holes filled; scale from aimpoint-pro.mount_length = 2.771 in (median width over 0.725–0.785 of the height from the top, 777–778 px 777 px → 280.4 px/in); origin at x center, y min of the outline (x over 0.725–0.785 of the height from the top); Douglas-Peucker at 0.005 in with the extremes kept: 130 points (IoU 0.998 with the full outline); checks: centre between the top (max over 0.0 in windows) along x [-2.11, -2.07] 2.289 ± 0.020; features through the same placement (front_ring: the front lens cover's rubber ring round the bell's front end: its end to its seam with the bell; its top is under the hinge (cut); bell: the objective bell between the front cover ring and the ring's front face; ring: the 30 mm ring (Base & Top Ring) round the tube: its front face to its rear face, its top to the ring base's foot; ring_split: the ring's split: the band between the top ring's lower edge and the base's upper edge, where the two screws are; ring_ears: the top ring's flats each side of its round, the band under its two screws' heads, down to the split; ring_screws: the heads of the ring's two screws on the near (left) flat, standing up out of it: the front one, then the rear one; body: the main body behind the ring: its front face to where it narrows to the rear ring; battery: the battery housing along the top of the right shoulder, seen over the body's top: its knurled front cap's face to its rear end (the rotary switch, under the rear hinge); battery_cap: the battery cap: the knurled ring at the housing's front; elevation_cap: the elevation adjustment cap on the body's top, its strap beside it; rear_ring: the rear lens cover's rubber ring round the body's rear end, from its seam; foot: the ring base's foot: the plate the length of the mount that the ring stands on and the body rests on; spacer: the spacer, with its row of eight holes: from the groove under the foot to the line over the QRP2; holes: the spacer's eight through holes: the row's first hole's left edge to the last one's right, their tops and bottoms; qrp2: the QRP2's body on the left, from the line under the spacer to its lower edge; lip: the dark strip under the QRP2's left wall (its jaw's lip); jaw: the block the torque knob stands in, under the QRP2's left wall; knob: the torque knob, face on: its knurled ring's outline, a circle (rows 1321 to 1396 fit one of radius 132 px about row 1280, column 922); front_lid: the front lens cover's lid as photographed, raised and tilted open over the bell, its inside toward the lens: four corners, its hinge end's underside and top, its tip's underside and top; rear_lid: the rear lens cover's lid as photographed, raised and leaning forward over the battery housing: four corners, its foot at the hinge (front and rear) and its top; front_hinge: the front cover's hinge on top of its ring (the lug with its pin and the triangle), carried down to the cut over the ring; rear_hinge: the rear cover's hinge on top of its ring (the lug with the triangle), carried down to the cut over the ring) (tools/trace.py)","via":"harvest","note":"The raised lens covers' lids and hinges are cut out of it (the lids aren't the sight's outline; their rings round the two ends are). Everything else is inside the silhouette and is a feature: the cover rings' seams, the bell, the ring and its split, the main body, the battery housing and its cap, the elevation cap, the ring base's foot, the spacer and its holes, the QRP2, its jaw and the knob."}},"gaps":[{"what":"A straight view from the front, the rear or above","need":"A studio end view or top view on a plain ground: the main body's and the battery housing's section, how far the windage cap and the torque knob stand out, the ring's flats, the spacer's and the QRP2's widths. On file since the detail pass (2026-10-19), all oblique: Primary Arms' 12841_02 (e97955bbce77, from ahead and to the right, the QRP2's front end face against white), Optics Trade's sixteen photographs of the QRP2 alone (12195; 1000 px) and its photographs of the sight upside down (4015 px). A camera fitted to the first by the spacer's holes, the mount's ends and edges and the jaw's corner on the rail's flat fitted the mount to a quarter of a pixel and put the battery cap 160 px from where it is; with the battery cap or the front cover ring's rim it did not settle (the side profiles' heights, taken from a little above, carry a few hundredths each): its 0.57 to 0.63 in for the right face isn't a reading"},{"what":"The mount's own sizes","need":"The spacer's and the ring base's widths, the QRP2's left side and how its jaws' lower outer edges are shaped (Primary Arms' photograph and Aimpoint's front quarter show a change of facet along the right jaw's outer face about level with the rail's top, not resolved) are on no page and in no square view: the spacer, the foot and the QRP2's left side are drawn 0.55 in each side of the rail's middle (assumed), the QRP2's right jaw 0.59 in by Aimpoint's two widths (qrp2_right_inboard), its foot 0.316 in under the rail's top by the right profile. So drawn, the QRP2's right jaw stands 0.044 cu in into the tube's top beside the neck of Aero's Enhanced rail (0.047 before the detail pass), as the T-2's and the Duty RDS's mounts do, and 0.0013 to 0.0015 into the shoulders under the head of Geissele's 15 and 13.5 in MK16 and Expo's rail (app/tests/rail-clamps.test.ts, LOW_SHELF): the right jaw's lower outer edge from a square end view would say whether it clears them"},{"what":"Which of the maker's two generations of figures is the product sold now","need":"Aimpoint's own page for 12841 (it refuses the reader; a page the user saves from their own browser could be filed): 130 or 136 mm, 330 or 360 g, 192 or 220 g for the sight"},{"what":"What the configuration's 81 mm of height spans","need":"A drawing or a sentence: no reading on the photos lands on it (71.9 mm from the mount's lowest edge to the top, 74.6 from the jaws, 83.1 from the knob's lowest edge on Primary Arms' photograph)"},{"what":"Aimpoint's own pages (aimpoint.com, aimpoint.us)","need":"They refuse the project's reader and are left alone; a page the user saves from their own browser could be filed"}]},"armaspec-stealth-recoil-spring-gen4-c":{"id":"armaspec-stealth-recoil-spring-gen4-c","name":"Stealth™ Recoil Spring - SRS™- AR15 GEN4, C (3.3 oz)","manufacturer":"Armaspec","sku":"ARM253-C","url":"https://armaspec.com/stealthtm-recoil-spring-srstm-ar15-1.html","category":"buffer","description":"A buffer weight and its spring captured on a guide rod as one unit, in the receiver extension in place of both the buffer and the action spring. The maker's page: \"The Stealth Recoil Spring™ SRS™ GEN4 is a self-contained multi-stage drop-in replacement for your standard buffer and spring. The SRS™ is designed to keep the buffer spring from rubbing against the inner wall of the buffer tube providing smooth, quiet operation and the second stage helps reduce the felt recoil significantly.\" \"COMPATIBILITY: AR-15 with carbine-length buffer tube\"; \"Most bolt carriers have a rear opening of over .60″, there are a couple of bolt carriers in the market place that have a rear opening of under .60″ and will not function with the SRS.\" \"The polymer bumper goes towards the rear of the firearm and the metal weight mass goes towards the bolt carrier.\" \"The SRS can be installed with our without the buffer retainer.\" The C's weight is necked at its rear and turned out to the full diameter ahead of the neck; the H, H2 and H3 are plain cylinders of growing length. The maker's guide names the C for a suppressed 5.56 with a 16 in barrel, carbine or mid-length gas (\"Perfect. A 3.3/SRS-C is what you need!\"), and for a suppressed 14.5 in on a mid-length gas system.","weight":"armaspec-stealth-recoil-spring-gen4-c.weight","occupies":["buffer_spring"],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"bore":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the axis at the weight's front face, +x rearward (toward the bumper)."}},"interfaces":{"bore":{"type":"ar15.extension_bore","role":"buffer","anchor":"bore","params":{},"flips":false}},"materials":{"weight":{"label":"Weight","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"Stainless steel, bare (the maker's page: \"new version with stainless steel weight\"; MidwayUSA: \"Material Stainless Steel\"; Midwest Gun Works: \"Finish / Color: Stainless Steel,Black\"). Bright metal: its finish type is its look (not fitted to a photo)."},"bumper":{"label":"Bumper","finish":"polymer","recolorable":false,"color":"placeholder-polymer-black","note":"\"The polymer bumper\" (the maker's page), black in every photo."},"rod":{"label":"Rod","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"The rod, its cap, the washer between the springs and the roll pin across the bumper: bright bare metal in the maker's photos."},"spring":{"label":"Springs","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"The main and the second spring: bright wire in the maker's photos (the second a darker bronze grey in Primary Arms'), drawn as the rod's metal."}},"components":{},"geometry":{"model":"armaspec-stealth-recoil-spring-gen4-c.glb","components":{},"approximations":["Drawn as it stands out of the rifle, at its free length: the weight against the rod's cap, its front face on the carrier's rear (the part's origin) and the bumper 7.18 in behind it. A carbine extension leaves 7.226 in from the carrier's rear to its rear wall (the standard buffer's head and the room its spring has, ± 0.03), so the bumper is drawn 0.05 in short of the wall; the maker's \"constant tension against the bolt carrier\" would have the carrier hold the weight back on the rod by that much, which no figure on file says.","Every size but the length and the weights is read on the maker's photos (the ledger says which and how), scaled by the length; the rod's cap, its depth in the weight's front bore, the slot's depth in the bumper and the rod's end inside it are assumed (the ledger's entries marked so).","The C's neck is a straight run and one cone out to the full diameter, as the maker's side view of the C shows it.","The springs are round wire on a helix at the length they stand in the photos, their end coils closed: the main spring from the bumper to the washer, the second, stiffer one from the washer to the weight's rear face. The rod is drawn stepped where it shows two sizes, thin under the main spring and thicker under the second; whether the thicker part is the rod or a sleeve on it isn't seen.","The rod has its cross hole for a hex key just ahead of the washer (Redcon1's sentence; seen in the H2's photo), at a 3/32 in key's size.","Not drawn: the engraving on the weight (ARMASPEC, the version and its weight; the C's logo), the patent numbers on the bumper's rear face, the second spring's last coil going into a shallow recess in the weight's rear face, the two 3/32 in hex screws Primary Arms names (Redcon1: \"the hole in the rod for leverage\"), and the thread locker."],"ledger":["armaspec-stealth-recoil-spring-gen4-c.length","armaspec-stealth-recoil-spring-gen4-c.od","armaspec-stealth-recoil-spring-gen4-c.weight_length","armaspec-stealth-recoil-spring-gen4-h.bumper_d","armaspec-stealth-recoil-spring-gen4-h.rod_d","armaspec-stealth-recoil-spring-gen4-h.sleeve_d","armaspec-stealth-recoil-spring-gen4-h.washer_od","armaspec-stealth-recoil-spring-gen4-h.main_spring_od","armaspec-stealth-recoil-spring-gen4-h.main_wire_d","armaspec-stealth-recoil-spring-gen4-h.main_coils","armaspec-stealth-recoil-spring-gen4-h.second_spring_od","armaspec-stealth-recoil-spring-gen4-h.second_wire_d","armaspec-stealth-recoil-spring-gen4-h.second_coils","armaspec-stealth-recoil-spring-gen4-h.counterbore_d","armaspec-stealth-recoil-spring-gen4-h.rod_hole_d","armaspec-stealth-recoil-spring-gen4-h.rod_hole_ahead","armaspec-stealth-recoil-spring-gen4-c.neck_d","armaspec-stealth-recoil-spring-gen4-c.neck_length","armaspec-stealth-recoil-spring-gen4-c.neck_taper","armaspec-stealth-recoil-spring-gen4-h.bumper_length","armaspec-stealth-recoil-spring-gen4-h.washer_front_x"]},"profiles":{},"gaps":[{"what":"The rod, the cap and the weight's bore","need":"A drawing, or an owner's measurements of the unit taken apart; the maker's design patent D864337 (marked on the bumper) is of an earlier generation's weight and gives no size"},{"what":"Where the unit stands in the rifle","need":"A figure for how far the carrier pushes the weight back on its rod with the bolt forward (the maker: 'Buffer mass is designed to stay under constant tension against the bolt carrier'), or a photo of it in a cut-away tube"},{"what":"What the steel as drawn lacks","need":"At stainless steel's density the model's steel is 4.95 oz of the maker's 6.2 oz, which would leave the bumper at 1.32 oz to the cubic inch, denser than a common polymer: something not seen in a photo (the rod's end inside the bumper, the weight's bore, a steel insert) holds 0.3 to 0.7 oz more. A photo or a description of the unit taken apart would close it"}]},"armaspec-stealth-recoil-spring-gen4-h":{"id":"armaspec-stealth-recoil-spring-gen4-h","name":"Stealth™ Recoil Spring - SRS™- AR15 GEN4, H (3.8 oz)","manufacturer":"Armaspec","sku":"ARM253-H","url":"https://armaspec.com/stealthtm-recoil-spring-srstm-ar15-1.html","category":"buffer","description":"A buffer weight and its spring captured on a guide rod as one unit, in the receiver extension in place of both the buffer and the action spring. The maker's page: \"The Stealth Recoil Spring™ SRS™ GEN4 is a self-contained multi-stage drop-in replacement for your standard buffer and spring. The SRS™ is designed to keep the buffer spring from rubbing against the inner wall of the buffer tube providing smooth, quiet operation and the second stage helps reduce the felt recoil significantly.\" \"COMPATIBILITY: AR-15 with carbine-length buffer tube\"; \"Most bolt carriers have a rear opening of over .60″, there are a couple of bolt carriers in the market place that have a rear opening of under .60″ and will not function with the SRS.\" \"The polymer bumper goes towards the rear of the firearm and the metal weight mass goes towards the bolt carrier.\" \"The SRS can be installed with our without the buffer retainer.\" The H's weight is a plain cylinder; the C's is necked, the H2's and the H3's are longer. The maker's guide names the H, or the H2, for a suppressed 5.56 with a 14.5 in barrel and a carbine gas system (\"Perfect. A 3.8/SRS-H or a 4.7/SRS-H2 is what you need!\").","weight":"armaspec-stealth-recoil-spring-gen4-h.weight","occupies":["buffer_spring"],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"bore":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the axis at the weight's front face, +x rearward (toward the bumper)."}},"interfaces":{"bore":{"type":"ar15.extension_bore","role":"buffer","anchor":"bore","params":{},"flips":false}},"materials":{"weight":{"label":"Weight","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"Stainless steel, bare (the maker's page: \"new version with stainless steel weight\"; MidwayUSA: \"Material Stainless Steel\"; Midwest Gun Works: \"Finish / Color: Stainless Steel,Black\"). Bright metal: its finish type is its look (not fitted to a photo)."},"bumper":{"label":"Bumper","finish":"polymer","recolorable":false,"color":"placeholder-polymer-black","note":"\"The polymer bumper\" (the maker's page), black in every photo."},"rod":{"label":"Rod","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"The rod, its cap, the washer between the springs and the roll pin across the bumper: bright bare metal in the maker's photos."},"spring":{"label":"Springs","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"The main and the second spring: bright wire in the maker's photos (the second a darker bronze grey in Primary Arms'), drawn as the rod's metal."}},"components":{},"geometry":{"model":"armaspec-stealth-recoil-spring-gen4-h.glb","components":{},"approximations":["Drawn as it stands out of the rifle, at its free length: the weight against the rod's cap, its front face on the carrier's rear (the part's origin) and the bumper 7.18 in behind it. A carbine extension leaves 7.226 in from the carrier's rear to its rear wall (the standard buffer's head and the room its spring has, ± 0.03), so the bumper is drawn 0.05 in short of the wall; the maker's \"constant tension against the bolt carrier\" would have the carrier hold the weight back on the rod by that much, which no figure on file says.","Every size but the length and the weights is read on the maker's photos (the ledger says which and how), scaled by the length; the rod's cap, its depth in the weight's front bore, the slot's depth in the bumper and the rod's end inside it are assumed (the ledger's entries marked so).","The springs are round wire on a helix at the length they stand in the photos, their end coils closed: the main spring from the bumper to the washer, the second, stiffer one from the washer to the weight's rear face. The rod is drawn stepped where it shows two sizes, thin under the main spring and thicker under the second; whether the thicker part is the rod or a sleeve on it isn't seen.","The rod has its cross hole for a hex key just ahead of the washer (Redcon1's sentence; seen in the H2's photo), at a 3/32 in key's size.","Not drawn: the engraving on the weight (ARMASPEC, the version and its weight; the C's logo), the patent numbers on the bumper's rear face, the second spring's last coil going into a shallow recess in the weight's rear face, the two 3/32 in hex screws Primary Arms names (Redcon1: \"the hole in the rod for leverage\"), and the thread locker."],"ledger":["armaspec-stealth-recoil-spring-gen4-h.length","armaspec-stealth-recoil-spring-gen4-h.od","armaspec-stealth-recoil-spring-gen4-h.weight_length","armaspec-stealth-recoil-spring-gen4-h.bumper_d","armaspec-stealth-recoil-spring-gen4-h.rod_d","armaspec-stealth-recoil-spring-gen4-h.sleeve_d","armaspec-stealth-recoil-spring-gen4-h.washer_od","armaspec-stealth-recoil-spring-gen4-h.main_spring_od","armaspec-stealth-recoil-spring-gen4-h.main_wire_d","armaspec-stealth-recoil-spring-gen4-h.main_coils","armaspec-stealth-recoil-spring-gen4-h.second_spring_od","armaspec-stealth-recoil-spring-gen4-h.second_wire_d","armaspec-stealth-recoil-spring-gen4-h.second_coils","armaspec-stealth-recoil-spring-gen4-h.counterbore_d","armaspec-stealth-recoil-spring-gen4-h.rod_hole_d","armaspec-stealth-recoil-spring-gen4-h.rod_hole_ahead","armaspec-stealth-recoil-spring-gen4-h.bumper_length","armaspec-stealth-recoil-spring-gen4-h.washer_front_x"]},"profiles":{},"gaps":[{"what":"The rod, the cap and the weight's bore","need":"A drawing, or an owner's measurements of the unit taken apart; the maker's design patent D864337 (marked on the bumper) is of an earlier generation's weight and gives no size"},{"what":"Where the unit stands in the rifle","need":"A figure for how far the carrier pushes the weight back on its rod with the bolt forward (the maker: 'Buffer mass is designed to stay under constant tension against the bolt carrier'), or a photo of it in a cut-away tube"},{"what":"What the steel as drawn lacks","need":"At stainless steel's density the model's steel is 5.49 oz of the maker's 6.6 oz, which would leave the bumper at 1.17 oz to the cubic inch, denser than a common polymer: something not seen in a photo (the rod's end inside the bumper, the weight's bore, a steel insert) holds 0.3 to 0.7 oz more. A photo or a description of the unit taken apart would close it"}]},"armaspec-stealth-recoil-spring-gen4-h2":{"id":"armaspec-stealth-recoil-spring-gen4-h2","name":"Stealth™ Recoil Spring - SRS™- AR15 GEN4, H2 (4.7 oz)","manufacturer":"Armaspec","sku":"ARM253-H2","url":"https://armaspec.com/stealthtm-recoil-spring-srstm-ar15-1.html","category":"buffer","description":"A buffer weight and its spring captured on a guide rod as one unit, in the receiver extension in place of both the buffer and the action spring. The maker's page: \"The Stealth Recoil Spring™ SRS™ GEN4 is a self-contained multi-stage drop-in replacement for your standard buffer and spring. The SRS™ is designed to keep the buffer spring from rubbing against the inner wall of the buffer tube providing smooth, quiet operation and the second stage helps reduce the felt recoil significantly.\" \"COMPATIBILITY: AR-15 with carbine-length buffer tube\"; \"Most bolt carriers have a rear opening of over .60″, there are a couple of bolt carriers in the market place that have a rear opening of under .60″ and will not function with the SRS.\" \"The polymer bumper goes towards the rear of the firearm and the metal weight mass goes towards the bolt carrier.\" \"The SRS can be installed with our without the buffer retainer.\" The H2's weight is the H's, longer, over a second spring held shorter. The maker's guide names the H2 for a suppressed 5.56 with an 11.5 in barrel (\"Perfect. A 4.7/SRS-H2 is what you need!\"), the H2 or the H for a suppressed 14.5 in carbine, and the H2 or the H3 for a suppressed 10.5 in.","weight":"armaspec-stealth-recoil-spring-gen4-h2.weight","occupies":["buffer_spring"],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"bore":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the axis at the weight's front face, +x rearward (toward the bumper)."}},"interfaces":{"bore":{"type":"ar15.extension_bore","role":"buffer","anchor":"bore","params":{},"flips":false}},"materials":{"weight":{"label":"Weight","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"Stainless steel, bare (the maker's page: \"new version with stainless steel weight\"; MidwayUSA: \"Material Stainless Steel\"; Midwest Gun Works: \"Finish / Color: Stainless Steel,Black\"). Bright metal: its finish type is its look (not fitted to a photo)."},"bumper":{"label":"Bumper","finish":"polymer","recolorable":false,"color":"placeholder-polymer-black","note":"\"The polymer bumper\" (the maker's page), black in every photo."},"rod":{"label":"Rod","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"The rod, its cap, the washer between the springs and the roll pin across the bumper: bright bare metal in the maker's photos."},"spring":{"label":"Springs","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"The main and the second spring: bright wire in the maker's photos (the second a darker bronze grey in Primary Arms'), drawn as the rod's metal."}},"components":{},"geometry":{"model":"armaspec-stealth-recoil-spring-gen4-h2.glb","components":{},"approximations":["Drawn as it stands out of the rifle, at its free length: the weight against the rod's cap, its front face on the carrier's rear (the part's origin) and the bumper 7.18 in behind it. A carbine extension leaves 7.226 in from the carrier's rear to its rear wall (the standard buffer's head and the room its spring has, ± 0.03), so the bumper is drawn 0.05 in short of the wall; the maker's \"constant tension against the bolt carrier\" would have the carrier hold the weight back on the rod by that much, which no figure on file says.","Every size but the length and the weights is read on the maker's photos (the ledger says which and how), scaled by the length; the rod's cap, its depth in the weight's front bore, the slot's depth in the bumper and the rod's end inside it are assumed (the ledger's entries marked so).","The springs are round wire on a helix at the length they stand in the photos, their end coils closed: the main spring from the bumper to the washer, the second, stiffer one from the washer to the weight's rear face. The rod is drawn stepped where it shows two sizes, thin under the main spring and thicker under the second; whether the thicker part is the rod or a sleeve on it isn't seen.","The weight's rear face has a pocket the second spring's end goes into (the coils it hides in the maker's side view): its depth read on the photos, its diameter assumed a little over the spring's. The rod has its cross hole for a hex key just ahead of the washer (Redcon1's sentence; seen in the H2's photo), at a 3/32 in key's size.","Not drawn: the engraving on the weight (ARMASPEC, the version and its weight; the C's logo), the patent numbers on the bumper's rear face, the two 3/32 in hex screws Primary Arms names (Redcon1: \"the hole in the rod for leverage\"), and the thread locker."],"ledger":["armaspec-stealth-recoil-spring-gen4-h2.length","armaspec-stealth-recoil-spring-gen4-h2.od","armaspec-stealth-recoil-spring-gen4-h2.weight_length","armaspec-stealth-recoil-spring-gen4-h.bumper_d","armaspec-stealth-recoil-spring-gen4-h.rod_d","armaspec-stealth-recoil-spring-gen4-h.sleeve_d","armaspec-stealth-recoil-spring-gen4-h.washer_od","armaspec-stealth-recoil-spring-gen4-h.main_spring_od","armaspec-stealth-recoil-spring-gen4-h.main_wire_d","armaspec-stealth-recoil-spring-gen4-h.main_coils","armaspec-stealth-recoil-spring-gen4-h.second_spring_od","armaspec-stealth-recoil-spring-gen4-h.second_wire_d","armaspec-stealth-recoil-spring-gen4-h.second_coils","armaspec-stealth-recoil-spring-gen4-h.counterbore_d","armaspec-stealth-recoil-spring-gen4-h.pocket_d","armaspec-stealth-recoil-spring-gen4-h2.spring_pocket_depth","armaspec-stealth-recoil-spring-gen4-h.rod_hole_d","armaspec-stealth-recoil-spring-gen4-h.rod_hole_ahead","armaspec-stealth-recoil-spring-gen4-h.bumper_length","armaspec-stealth-recoil-spring-gen4-h.washer_front_x"]},"profiles":{},"gaps":[{"what":"The rod, the cap and the weight's bore","need":"A drawing, or an owner's measurements of the unit taken apart; the maker's design patent D864337 (marked on the bumper) is of an earlier generation's weight and gives no size"},{"what":"Where the unit stands in the rifle","need":"A figure for how far the carrier pushes the weight back on its rod with the bolt forward (the maker: 'Buffer mass is designed to stay under constant tension against the bolt carrier'), or a photo of it in a cut-away tube"},{"what":"What the steel as drawn lacks","need":"At stainless steel's density the model's steel is 6.24 oz of the maker's 7.4 oz, which would leave the bumper at 1.23 oz to the cubic inch, denser than a common polymer: something not seen in a photo (the rod's end inside the bumper, the weight's bore, a steel insert) holds 0.3 to 0.7 oz more. A photo or a description of the unit taken apart would close it"}]},"armaspec-stealth-recoil-spring-gen4-h3":{"id":"armaspec-stealth-recoil-spring-gen4-h3","name":"Stealth™ Recoil Spring - SRS™- AR15 GEN4, H3 (5.6 oz)","manufacturer":"Armaspec","sku":"ARM253-H3","url":"https://armaspec.com/stealthtm-recoil-spring-srstm-ar15-1.html","category":"buffer","description":"A buffer weight and its spring captured on a guide rod as one unit, in the receiver extension in place of both the buffer and the action spring. The maker's page: \"The Stealth Recoil Spring™ SRS™ GEN4 is a self-contained multi-stage drop-in replacement for your standard buffer and spring. The SRS™ is designed to keep the buffer spring from rubbing against the inner wall of the buffer tube providing smooth, quiet operation and the second stage helps reduce the felt recoil significantly.\" \"COMPATIBILITY: AR-15 with carbine-length buffer tube\"; \"Most bolt carriers have a rear opening of over .60″, there are a couple of bolt carriers in the market place that have a rear opening of under .60″ and will not function with the SRS.\" \"The polymer bumper goes towards the rear of the firearm and the metal weight mass goes towards the bolt carrier.\" \"The SRS can be installed with our without the buffer retainer.\" The H3's weight is the longest, and its bumper is half the others' length. The maker's guide names the H3, or the H2, for a suppressed 5.56 with a 10.5 in barrel (\"Perfect. A 4.7/SRS-H2 or a 5.6/SRS-H3 is what you need!\").","weight":"armaspec-stealth-recoil-spring-gen4-h3.weight","occupies":["buffer_spring"],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"bore":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the axis at the weight's front face, +x rearward (toward the bumper)."}},"interfaces":{"bore":{"type":"ar15.extension_bore","role":"buffer","anchor":"bore","params":{},"flips":false}},"materials":{"weight":{"label":"Weight","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"Stainless steel, bare (the maker's page: \"new version with stainless steel weight\"; MidwayUSA: \"Material Stainless Steel\"; Midwest Gun Works: \"Finish / Color: Stainless Steel,Black\"). Bright metal: its finish type is its look (not fitted to a photo)."},"bumper":{"label":"Bumper","finish":"polymer","recolorable":false,"color":"placeholder-polymer-black","note":"\"The polymer bumper\" (the maker's page), black in every photo."},"rod":{"label":"Rod","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"The rod, its cap, the washer between the springs and the roll pin across the bumper: bright bare metal in the maker's photos."},"spring":{"label":"Springs","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"The main and the second spring: bright wire in the maker's photos (the second a darker bronze grey in Primary Arms'), drawn as the rod's metal."}},"components":{},"geometry":{"model":"armaspec-stealth-recoil-spring-gen4-h3.glb","components":{},"approximations":["Drawn as it stands out of the rifle, at its free length: the weight against the rod's cap, its front face on the carrier's rear (the part's origin) and the bumper 7.18 in behind it. A carbine extension leaves 7.226 in from the carrier's rear to its rear wall (the standard buffer's head and the room its spring has, ± 0.03), so the bumper is drawn 0.05 in short of the wall; the maker's \"constant tension against the bolt carrier\" would have the carrier hold the weight back on the rod by that much, which no figure on file says.","Every size but the length and the weights is read on the maker's photos (the ledger says which and how), scaled by the length; the rod's cap, its depth in the weight's front bore, the slot's depth in the bumper and the rod's end inside it are assumed (the ledger's entries marked so).","The springs are round wire on a helix at the length they stand in the photos, their end coils closed: the main spring from the bumper to the washer, the second, stiffer one from the washer to the weight's rear face. The rod is drawn stepped where it shows two sizes, thin under the main spring and thicker under the second; whether the thicker part is the rod or a sleeve on it isn't seen.","The weight's rear face has a pocket the second spring's end goes into (the coils it hides in the maker's side view): its depth read on the photos, its diameter assumed a little over the spring's. The rod has its cross hole for a hex key just ahead of the washer (Redcon1's sentence; seen in the H2's photo), at a 3/32 in key's size.","Not drawn: the engraving on the weight (ARMASPEC, the version and its weight; the C's logo), the patent numbers on the bumper's rear face, the two 3/32 in hex screws Primary Arms names (Redcon1: \"the hole in the rod for leverage\"), and the thread locker."],"ledger":["armaspec-stealth-recoil-spring-gen4-h3.length","armaspec-stealth-recoil-spring-gen4-h3.od","armaspec-stealth-recoil-spring-gen4-h3.weight_length","armaspec-stealth-recoil-spring-gen4-h.bumper_d","armaspec-stealth-recoil-spring-gen4-h.rod_d","armaspec-stealth-recoil-spring-gen4-h.sleeve_d","armaspec-stealth-recoil-spring-gen4-h.washer_od","armaspec-stealth-recoil-spring-gen4-h.main_spring_od","armaspec-stealth-recoil-spring-gen4-h.main_wire_d","armaspec-stealth-recoil-spring-gen4-h3.main_coils","armaspec-stealth-recoil-spring-gen4-h.second_spring_od","armaspec-stealth-recoil-spring-gen4-h.second_wire_d","armaspec-stealth-recoil-spring-gen4-h.second_coils","armaspec-stealth-recoil-spring-gen4-h.counterbore_d","armaspec-stealth-recoil-spring-gen4-h.pocket_d","armaspec-stealth-recoil-spring-gen4-h3.spring_pocket_depth","armaspec-stealth-recoil-spring-gen4-h.rod_hole_d","armaspec-stealth-recoil-spring-gen4-h.rod_hole_ahead","armaspec-stealth-recoil-spring-gen4-h3.bumper_length","armaspec-stealth-recoil-spring-gen4-h3.washer_front_x"]},"profiles":{},"gaps":[{"what":"The rod, the cap and the weight's bore","need":"A drawing, or an owner's measurements of the unit taken apart; the maker's design patent D864337 (marked on the bumper) is of an earlier generation's weight and gives no size"},{"what":"Where the unit stands in the rifle","need":"A figure for how far the carrier pushes the weight back on its rod with the bolt forward (the maker: 'Buffer mass is designed to stay under constant tension against the bolt carrier'), or a photo of it in a cut-away tube"},{"what":"What the steel as drawn lacks","need":"At stainless steel's density the model's steel is 7.25 oz of the maker's 8.0 oz, which would leave the bumper at 1.48 oz to the cubic inch, denser than a common polymer: something not seen in a photo (the rod's end inside the bumper, the weight's bore, a steel insert) holds 0.3 to 0.7 oz more. A photo or a description of the unit taken apart would close it"}]},"b5-bravo-stock":{"id":"b5-bravo-stock","name":"Bravo Stock","manufacturer":"B5 Systems","sku":"BRV-1082","url":"https://b5systems.com/collection/ar/bravo-stock/","category":"stock","description":"B5 Systems' slim carbine stock: the SOPMOD's winged cheek round the tube with no storage tubes, an angled butt with a cushioned pad, a steel QD socket through the frame and two sling slots. For mil-spec carbine receiver extensions. Its shape is the maker's design patent's, scaled by the three sizes its page gives. B5's page heads it in capitals, BRAVO STOCK.","weight":"b5-bravo-stock.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"butt":{"origin":[0,0,0],"note":"The butt's plane on the tube axis: the part frame's origin (the pad's rearmost point, near its top: the butt is angled, its toe further forward). Overall length and length of pull end here."},"tube":{"origin":["{.butt_behind_pin_pos1}",0,0],"x":[-1,0,0],"note":"Stock frame: origin on the tube axis in the plane of the butt, +x forward. At position 1 this anchor sits at the takedown pin's X."}},"interfaces":{"tube":{"type":"receiver_extension","role":"stock","anchor":"tube","params":{"profile":"mil-spec"},"flips":false,"note":"B5's page: \"Fits MIL-SPEC Carbine Receiver Extensions\". No commercial-spec Bravo is on its page."}},"materials":{"body":{"label":"Stock body","finish":"polymer","recolorable":true,"color":"placeholder-polymer-black","sheen":"satin","options":{"black":{"label":"Black","finish":"polymer","color":"placeholder-polymer-black","sheen":"satin","sku":"BRV-1082","source":"https://b5systems.com/collection/ar/bravo-stock/"},"fde":{"label":"Flat Dark Earth","finish":"polymer","color":"b5-fde","sheen":"satin","sku":"BRV-1085","source":"https://b5systems.com/collection/ar/bravo-stock/"},"coyote":{"label":"Coyote Brown","finish":"polymer","color":"b5-coyote-brown","sheen":"satin","sku":"BRV-1086","source":"https://b5systems.com/collection/ar/bravo-stock/"},"odg":{"label":"OD Green","finish":"polymer","color":"b5-od-green","sheen":"satin","sku":"BRV-1104","source":"https://b5systems.com/collection/ar/bravo-stock/"},"wolf":{"label":"Wolf Grey","finish":"polymer","color":"b5-wolf-grey","sheen":"satin","sku":"BRV-1117","source":"https://b5systems.com/collection/ar/bravo-stock/"}},"default":"black","note":"B5's five solid colours, each by the name and the number its page's variation data gives it (Black BRV-1082, Flat Dark Earth BRV-1085, Coyote Brown BRV-1086, OD Green BRV-1104, Wolf Grey BRV-1117), the four colours each matched on B5's own picture of it (BRV-<number>_PROFILE_RIGHT.png: one series under one light, the Enhanced SOPMOD's with it; data/colors/b5-systems.yaml). The black is the catalog's placeholder polymer black: a black of B5's own was tried on the Enhanced SOPMOD and the fit ran to the floor. Sold too and not offered here, a printed pattern being no one colour: MultiCam® (BRV-1088), MultiCam® Black (BRV-1421), Woodland (BRV-1184) and Tiger Stripe (BRV-1580). The cheek, the frame, the lever and the pad's release tabs are this slot. B5 names no finish for the polymer but \"Made of MIL-SPEC Materials and Finishes\"; the cheek's skin is a fine pebble in its pictures, the lever's smooth."},"buttpad":{"label":"Buttpad","finish":"rubber","recolorable":false,"color":"placeholder-black","follows":{"slot":"body","options":{"fde":{"finish":"rubber","color":"b5-fde-rubber"},"coyote":{"finish":"rubber","color":"b5-coyote-brown-rubber"},"odg":{"finish":"rubber","color":"b5-od-green-rubber"},"wolf":{"finish":"rubber","color":"b5-wolf-grey-rubber"}}},"note":"B5: \"Cushioned Non-slip Buttpad\". The stock's colour on every one: B5's five pictures show the pad in black, flat dark earth, coyote brown, OD green and wolf grey with the cheek (Primary Arms' photos of the flat dark earth one and T.REX ARMS' of the coyote one agree), a smooth matte rubber that reads a little lighter than the pebbled cheek beside it. The black one is a placeholder black: B5's picture has it a charcoal lighter than the cheek (#545456 against #37383b)."},"qd":{"label":"QD socket","finish":"steel","recolorable":false,"color":"placeholder-black","follows":{"slot":"body","options":{"fde":{"finish":"cerakote","color":"b5-fde-steel"},"coyote":{"finish":"cerakote","color":"b5-coyote-brown-steel"},"odg":{"finish":"cerakote","color":"b5-od-green-steel"},"wolf":{"finish":"cerakote","color":"b5-wolf-grey-steel"}}},"note":"B5: \"Fixed Sling Mounts and Steel Anti-Rotational QD Mounts\" and \"Color-Matched Steel Hardware\"; one steel piece through the frame, a socket each side (the sellers' three-quarter views). On the black stock its face round the hole is a dark steel inside the polymer's lip (B5's picture, #3b3a35); on the four colours it is coated in the stock's colour (B5's picture of each). B5 names neither the steel's black nor the coat: the black is drawn as `steel`, the coloured ones as a matte sprayed coat (`cerakote`, the nearest type the catalog has; it isn't B5's word)."},"pin":{"label":"Lock pin","finish":"steel","recolorable":false,"color":"placeholder-black","follows":{"slot":"body","options":{"fde":{"finish":"cerakote","color":"b5-fde-steel"},"coyote":{"finish":"cerakote","color":"b5-coyote-brown-steel"},"odg":{"finish":"cerakote","color":"b5-od-green-steel"},"wolf":{"finish":"cerakote","color":"b5-wolf-grey-steel"}}},"note":"The lock pin's end under the lever, steel: black on the black stock, coated in the stock's colour on the four others (B5's five pictures, read beside the QD socket's steel), drawn as the socket is. The roll pin through its cross hole is bare bright steel on every colour (B5's five pictures) and isn't drawn: a dozen pixels across in B5's 2000 px picture, and the hole it stands in isn't cut."}},"components":{"body":{"label":"Stock body","material":"body"},"buttpad":{"label":"Buttpad","material":"buttpad"},"qd":{"label":"QD socket","material":"qd"},"pin":{"label":"Lock pin","material":"pin"}},"geometry":{"model":"b5-bravo-stock.glb","components":{},"approximations":["Visual hull of three outlines: B5's own straight side photo (scaled by its 7.2 x 4.9 in, which fit it within 1.3%) and the back and top views of the design patent its page marks (US D722,669 S: FIG. 3 scaled by 4.9 x 2 in, which fit it within 0.3%; FIG. 5 scaled by 7.2 x 2 in, within 0.8%). The back view's section holds along the stock wherever the other two show it.","The frame below the cheek is cut to one width, 0.62 in (the patent's bottom view shows its strut 0.58 in wide behind the lever and 0.73 near the butt, its front view the block under the tube's front 0.50). The plate the butt pad sits on keeps the pad's width, and the frame steps in ahead of it.","The frame's relief (2026-10-19): each side is cut down to a thin web at the middle, 0.07 in thick (read through a camera fitted to T.REX ARMS' photo of the coyote stock from ahead and below: a sling slot's far rim shows just off its near one), leaving at the frame's face a rim 0.19 in wide along the strut and along the front and the bottom of the panel ahead of the lever (B5's side photo), one straight rib 0.066 in wide from the triangle's top rear corner through the QD socket to the strut, the socket's boss (0.69 in across its face, 0.81 at its foot: a drafted wall, read off the dark ring round it in the side photo) and a round housing over the lock pin as wide as the pin's end under the lever. The panels' walls are square and their corners sharp. ASSUMED: the rib's and the boss's faces are flush with the rim (relief_face_inset): the rib's reading through the camera agrees, the boss's height isn't read (the ledger's note). Along the pad's plate and under the cheek the web meets their faces with no rim of its own.","The wings' undersides are carried on as flat faces from where the butt pad hides them in the back view (from the corner that view draws under each wing, where the underside meets the pad's side) to the cheek's flat underside, 0.99 in wide in the patent's bottom view.","The adjustment lever is its side silhouette at the width the patent's bottom view gives it (0.86 in), a slab: its fork round the block under the tube and its hollow underside aren't drawn. The lock pin's lower end is a cylinder as wide as the block the side photo shows, a piece of its own under the lever (steel where the lever is polymer: the `pin` slot). The butt pad's release tabs are plain blocks, each as the side photo outlines it, out to the 1.03 in the patent's front view draws across the pair. The QD socket's steel is a ring round its hole, flush with the frame, out to where the steel ends in the photo. The two sling slots and the socket's hole are cut through.","The bore is the circle the patent's front view draws in hidden lines (1.162 in: the mil-spec tube's 1.148 and a little), with the indexing rail's channel under it (0.53 in wide, its floor 0.93 below the axis), cut from the front only as far back as the tube's rear end reaches when the stock is collapsed; the mouth's flare isn't drawn. The round hole on the cheek's top (0.32 in, over the lock pin) is cut through into it.","Not drawn: the butt pad's checkered face (the patent gives its grid, nothing its depth), the small windows near the cheek's rear, the B5 mark in its panel ahead of the lever, the fillets round the rib's and the boss's feet, the markings. Edges broken at 0.03 in.","Its seat on the tube is not read from a photo of it on a rifle: its lock pin (5.15 in ahead of the butt in B5's photo) stands in the tube's front hole, ± 0.08 in, which leaves its front 0.51 in behind the castle nut when collapsed."],"ledger":["b5-bravo-stock.length","b5-bravo-stock.height","b5-bravo-stock.width","b5-bravo-stock.tube_axis_below_top","b5-bravo-stock.frame_width","b5-bravo-stock.keel_width","b5-bravo-stock.lever_width","b5-bravo-stock.release_tab_span","b5-bravo-stock.bore_diameter","b5-bravo-stock.rail_channel_width","b5-bravo-stock.rail_channel_floor_below_axis","b5-bravo-stock.top_hole_ahead_of_butt","b5-bravo-stock.top_hole_diameter","b5-bravo-stock.lock_pin_ahead_of_butt","b5-bravo-stock.butt_behind_pin_pos1","b5-bravo-stock.frame_rim_width","b5-bravo-stock.rib_width","b5-bravo-stock.web_thickness","b5-bravo-stock.qd_boss_diameter","b5-bravo-stock.qd_boss_foot_diameter","b5-bravo-stock.relief_face_inset"]},"profiles":{"side":{"plane":"xy","origin":"rearmost point of the butt pad (x) and the cheek's top edge (y); the photo shows the top level, so the tube axis is horizontal","offset":{"y":"tube_axis_below_top"},"points":[[0,-0.348],[0.436,-4.725],[0.465,-4.81],[0.514,-4.869],[0.586,-4.912],[0.69,-4.931],[0.917,-4.902],[0.946,-4.921],[1.074,-4.921],[1.159,-4.902],[1.709,-4.433],[2.932,-3.442],[2.944,-3.445],[2.959,-3.848],[3.037,-3.912],[3.079,-3.916],[3.132,-3.897],[3.226,-3.802],[3.264,-3.798],[3.281,-3.748],[3.335,-3.727],[3.352,-3.677],[3.407,-3.656],[3.423,-3.606],[3.478,-3.584],[3.494,-3.535],[3.544,-3.518],[3.582,-3.452],[3.625,-3.442],[3.637,-3.397],[3.703,-3.364],[3.712,-3.321],[3.765,-3.302],[3.791,-3.243],[3.833,-3.234],[3.871,-3.167],[3.909,-3.162],[3.926,-3.113],[3.987,-3.084],[4.009,-3.03],[4.063,-3.008],[4.068,-2.97],[4.156,-2.883],[4.288,-2.802],[4.44,-2.769],[4.962,-2.759],[4.94,-2.771],[4.936,-2.814],[4.94,-3.046],[4.952,-3.063],[5.317,-3.068],[5.372,-3.042],[5.355,-2.75],[5.801,-2.731],[5.86,-2.676],[5.886,-2.57],[6.465,-2.575],[6.498,-2.56],[6.543,-2.515],[7.012,-1.686],[7.038,-1.655],[7.095,-1.64],[7.126,-1.6],[7.117,-1.211],[7.15,-0.965],[7.155,-0.69],[7.145,-0.23],[7.126,-0.102],[7.095,-0.043],[7.019,-0.014],[5.336,-0.005],[5.251,-0.028],[5.156,-0.033],[4.957,-0.005],[0.472,0],[0.453,-0.019],[0.192,-0.057],[0.107,-0.09],[0.047,-0.145],[0.009,-0.211]],"features":{"through":[[[1.408,-1.87],[1.422,-1.837],[1.477,-1.797],[2.776,-1.787],[2.809,-1.802],[2.845,-1.851],[2.826,-1.932],[2.767,-1.968],[1.776,-1.977],[1.453,-1.968],[1.413,-1.918]],[[1.636,-2.577],[1.645,-2.511],[1.674,-2.458],[1.733,-2.404],[1.795,-2.38],[1.87,-2.38],[1.951,-2.418],[2.006,-2.482],[2.025,-2.539],[2.025,-2.601],[1.991,-2.681],[1.932,-2.736],[1.847,-2.764],[1.771,-2.755],[1.709,-2.721],[1.659,-2.662]],[[1.19,-4.227],[1.19,-4.16],[1.235,-4.106],[2.179,-3.305],[2.254,-3.286],[2.309,-3.321],[2.318,-3.407],[2.254,-3.475],[1.292,-4.277],[1.23,-4.272]]],"buttpad":[[[-0.211,0.187],[0.462,0.187],[0.462,0.007],[0.486,-0.334],[0.51,-0.571],[0.538,-0.808],[0.567,-1.045],[0.595,-1.283],[0.619,-1.52],[0.642,-1.757],[0.661,-1.994],[0.685,-2.231],[0.714,-2.468],[0.737,-2.705],[0.761,-2.942],[0.785,-3.179],[0.808,-3.416],[0.832,-3.653],[0.851,-3.89],[0.87,-4.127],[0.889,-4.364],[0.913,-4.601],[0.932,-4.838],[0.941,-5.123],[-0.211,-5.123]]],"frame":[[[0.87,-1.652],[7.375,-1.652],[7.375,-4.08],[5.891,-4.08],[5.891,-2.563],[5.867,-2.373],[5.763,-2.221],[5.573,-2.145],[5.194,-2.112],[4.435,-2.107],[4.056,-2.126],[3.791,-2.183],[3.639,-2.335],[3.487,-2.525],[3.298,-2.714],[3.108,-2.923],[2.994,-3.056],[2.947,-3.132],[2.947,-5.313],[1.178,-5.313],[1.178,-4.933],[1.164,-4.838],[1.131,-4.601],[1.102,-4.364],[1.055,-3.89],[1.031,-3.653],[0.993,-3.179],[0.951,-2.705],[0.932,-2.468],[0.913,-2.231],[0.889,-1.994],[0.87,-1.7]]],"lever":[[[3.791,-2.183],[4.056,-2.126],[4.435,-2.107],[5.194,-2.112],[5.573,-2.145],[5.763,-2.221],[5.867,-2.373],[5.891,-2.563],[5.891,-4.08],[2.947,-4.08],[2.947,-3.132],[2.994,-3.056],[3.108,-2.923],[3.298,-2.714],[3.487,-2.525],[3.639,-2.335]]],"under":[[[0.808,-0.998],[7.375,-0.998],[7.375,-1.652],[0.87,-1.652]]],"pin":[[[4.943,-2.743],[5.369,-2.743],[5.369,-3.084],[4.943,-3.084]]],"tab":[[[1.008,-3.283],[1.283,-3.283],[1.283,-3.781],[1.008,-3.781]]],"qd":[[[1.548,-2.288],[2.117,-2.288],[2.117,-2.857],[1.548,-2.857]]]},"scaleRefs":["b5-bravo-stock.length","b5-bravo-stock.height"],"inputs":{"b5-bravo-stock.height":4.9,"b5-bravo-stock.length":7.2},"tolerance":0.01,"photo":"references/b5-bravo-stock c9a15e250f11 (B5: BRV-1082_PROFILE_RIGHT.png, straight right side on a transparent ground, 2000 x 2000)","method":"alpha > 0.5, largest piece, holes filled; scale from b5-bravo-stock.length = 7.2 in (x-extent 1509 px → 209.6 px/in) and b5-bravo-stock.height = 4.9 in (y-extent 1040 px → 212.2 px/in), which agree within 1.3%; mean 210.9 px/in; origin at x min, y max of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 80 points (IoU 0.998 with the full outline); features through the same placement (through: reviewed pixel boxes; buttpad: reviewed pixel boxes; frame: reviewed pixel boxes; lever: reviewed pixel boxes; under: reviewed pixel boxes; pin: reviewed pixel boxes; tab: reviewed pixel boxes; qd: reviewed pixel boxes) (tools/trace.py)","via":"harvest","note":"The two sling slots and the QD socket's hole are cut through. The lever and the lock pin's end are in the outline. The pad's release tab is a feature. The frame's recessed panels and the markings aren't."},"rear":{"plane":"zy","origin":"the top edge, centred: as the side profile, offset down to the tube axis","offset":{"y":"tube_axis_below_top"},"points":[[-0.998,-1.1],[-0.987,-1.167],[-0.95,-1.241],[-0.751,-1.422],[-0.754,-4.155],[-0.729,-4.347],[-0.692,-4.462],[-0.595,-4.621],[-0.449,-4.763],[-0.301,-4.848],[-0.202,-4.882],[0.05,-4.907],[0.301,-4.848],[0.468,-4.752],[0.629,-4.58],[0.729,-4.362],[0.754,-4.199],[0.751,-1.429],[0.969,-1.215],[0.998,-1.137],[0.998,-1.041],[0.965,-0.96],[0.758,-0.627],[0.754,-0.597],[0.64,-0.405],[0.499,-0.205],[0.405,-0.126],[0.276,-0.052],[0.135,-0.011],[-0.002,0],[-0.054,0],[-0.19,-0.022],[-0.294,-0.063],[-0.42,-0.137],[-0.51,-0.22],[-0.584,-0.32],[-0.962,-0.956],[-0.991,-1.03]],"scaleRefs":["b5-bravo-stock.height","b5-bravo-stock.width"],"inputs":{"b5-bravo-stock.height":4.9,"b5-bravo-stock.width":2},"tolerance":0.01,"photo":"references/b5-bravo-stock 38a078250167 (US D722,669 S, sheet 2 of 8, FIG. 3 back view, 300 dpi)","method":"luminance < 128, inside [480, 735, 1860, 1335], closing ×18, holes filled, inset 2 px (half the outline's stroke); rotated -90.0° as declared; scale from b5-bravo-stock.height = 4.9 in (y-extent 1327 px → 270.8 px/in) and b5-bravo-stock.width = 2 in (x-extent 540 px → 270.0 px/in), which agree within 0.3%; mean 270.4 px/in; origin at x center, y max of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 38 points (IoU 0.995 with the full outline) (tools/trace.py)","via":"harvest","note":"The sheet has the figure turned a quarter (the stock's top at the left). Seen from the rear: the round cheek and its two wings over the butt pad's stadium; symmetric."},"plan":{"plane":"xz","origin":"the butt pad's rear, centred","offset":{},"points":[[0,0.036],[0.014,-0.014],[0,-0.039],[0.014,-0.082],[0.004,-0.153],[0.014,-0.164],[0.007,-0.235],[0.021,-0.257],[0.014,-0.321],[0.029,-0.346],[0.021,-0.389],[0.054,-0.556],[0.103,-0.66],[0.159,-0.708],[0.255,-0.744],[0.523,-0.744],[0.74,-1.001],[6.116,-1.004],[6.227,-0.979],[6.662,-0.744],[7.093,-0.672],[7.156,-0.628],[7.17,-0.592],[7.17,0.592],[7.156,0.631],[7.115,0.669],[6.951,0.69],[6.762,0.74],[6.173,1.004],[0.74,1.004],[0.53,0.758],[0.237,0.754],[0.166,0.726],[0.096,0.663],[0.057,0.585],[0.032,0.4],[0.018,0.378],[0.025,0.321],[0.011,0.303],[0.018,0.235],[0.004,0.193],[0.014,0.071]],"scaleRefs":["b5-bravo-stock.length","b5-bravo-stock.width"],"inputs":{"b5-bravo-stock.length":7.2,"b5-bravo-stock.width":2},"tolerance":0.01,"photo":"references/b5-bravo-stock 41ee3b82c602 (US D722,669 S, sheet 4 of 8, FIG. 5 top view, 300 dpi)","method":"luminance < 128, inside [945, 610, 1560, 2675], closing ×18, holes filled, inset 2 px (half the outline's stroke); rotated +90.0° as declared; scale from b5-bravo-stock.length = 7.2 in (x-extent 2010 px → 279.2 px/in) and b5-bravo-stock.width = 2 in (y-extent 563 px → 281.5 px/in), which agree within 0.8%; mean 280.3 px/in; origin at x min, y center of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 42 points (IoU 0.998 with the full outline) (tools/trace.py)","via":"harvest","note":"The sheet has the butt at the top. Symmetric: the pad narrower than the cheek, the cheek tapering to the tube's collar at the front. The round hole on the top is in broken lines and isn't drawn."}},"gaps":[{"what":"Its seat on the tube from a photo (it is seated by its lock pin in the tube's front hole, ± 0.08 in)","need":"a straight side photo of it on a lower with both receiver pins in view, at any position"},{"what":"How light B5's colours are: its own pictures, which the five are matched on, are darker than the sellers' photos of the same stock (flat dark earth #786f62 on the lever's flat, against Primary Arms' and Wing Tactical's much paler tan; the blacks agree)","need":"a photo of a coloured stock beside a black one and a grey card, or on a rifle whose black parts set the exposure"},{"what":"What the steel hardware's black and its coloured coat are (B5 says only \"Color-Matched Steel Hardware\"), and whether the black pad is the cheek's black or a charcoal","need":"B5's or a seller's words for the finish; a photo of the black stock's pad beside its cheek in flat light"},{"what":"How deep the butt pad's checkering is; how far the QD boss's face and the rib's stand from the frame's face (drawn flush: the rib's reading through the camera agrees within ± 0.12 in; the boss's isn't read, its foot being hidden by the rib where the one fitted camera sees its wall); the web's thickness to better than ± 0.05 in (one photo, one camera: a second camera, fitted to T.REX ARMS' photo of the black stock from nearly the same corner, matched its outline less well and wasn't used)","need":"a photo square across the frame from behind or below with a known size in frame, or a second oblique from another corner with the camera fitted to it (B5's own photos are all straight side views)"},{"what":"How far back the bore runs and how its mouth is flared","need":"a photo into the stock's front, or the maker's drawing"},{"what":"A weight measured on a scale (B5 says 9.3 oz, its shop table 12, two sellers 9.6, two old reviews 8.25)","need":"a reviewer's weighing of the current stock, with the method"}]},"b5-enhanced-sopmod-stock":{"id":"b5-enhanced-sopmod-stock","name":"Enhanced SOPMOD Stock","manufacturer":"B5 Systems","sku":"SOP-1074","url":"https://b5systems.com/collection/ar/enhanced-sopmod-stock/","category":"stock","description":"B5 Systems' version of the Crane SOPMOD stock: a wide triangular housing round the tube whose two wings each hold a water-resistant storage tube and make the cheek rest, a cushioned butt pad, steel QD sockets through the frame and two sling slots. For mil-spec carbine receiver extensions. Its shape is B5's own side photo and the maker's design patent's views, scaled by the three sizes its page gives. B5's page heads it in capitals, ENHANCED SOPMOD STOCK; its other SOPMOD, the SOPMOD, GOVERNMENT ISSUE (SOP-1351), has no QD sockets and is another product.","weight":"b5-enhanced-sopmod-stock.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"butt":{"origin":[0,0,0],"note":"The butt's plane on the tube axis: the part frame's origin (the pad's rear face is square to the tube). Overall length and length of pull end here."},"tube":{"origin":["{.butt_behind_pin_pos1}",0,0],"x":[-1,0,0],"note":"Stock frame: origin on the tube axis in the plane of the butt, +x forward. At position 1 this anchor sits at the takedown pin's X."}},"interfaces":{"tube":{"type":"receiver_extension","role":"stock","anchor":"tube","params":{"profile":"mil-spec"},"flips":false,"note":"B5's page: \"Fits MIL-SPEC Carbine Receiver Extensions\". No commercial-spec Enhanced SOPMOD is on its page."}},"materials":{"body":{"label":"Stock body","finish":"polymer","recolorable":true,"color":"placeholder-polymer-black","sheen":"satin","options":{"black":{"label":"Black","finish":"polymer","color":"placeholder-polymer-black","sheen":"satin","sku":"SOP-1074","source":"https://b5systems.com/collection/ar/enhanced-sopmod-stock/"},"fde":{"label":"Flat Dark Earth","finish":"polymer","color":"b5-fde","sheen":"satin","sku":"SOP-1075","source":"https://b5systems.com/collection/ar/enhanced-sopmod-stock/"},"coyote":{"label":"Coyote Brown","finish":"polymer","color":"b5-coyote-brown","sheen":"satin","sku":"SOP-1076","source":"https://b5systems.com/collection/ar/enhanced-sopmod-stock/"},"odg":{"label":"OD Green","finish":"polymer","color":"b5-od-green","sheen":"satin","sku":"SOP-1097","source":"https://b5systems.com/collection/ar/enhanced-sopmod-stock/"},"wolf":{"label":"Wolf Grey","finish":"polymer","color":"b5-wolf-grey","sheen":"satin","sku":"SOP-1123","source":"https://b5systems.com/collection/ar/enhanced-sopmod-stock/"}},"default":"black","note":"B5's five solid colours, each by the name and the number its page's variation data gives it (Black SOP-1074, Flat Dark Earth SOP-1075, Coyote Brown SOP-1076, OD Green SOP-1097, Wolf Grey SOP-1123), the four colours each matched on B5's own picture of it (SOP-<number>_PROFILE_RIGHT.png: one series under one light; data/colors/b5-systems.yaml). The black is the catalog's placeholder polymer black: a black of B5's own was tried and the fit ran to the floor, the satin polymer's reflection being all that shows on the housing. Sold too and not offered here, a printed pattern being no one colour: MultiCam® (SOP-1078), MultiCam® Black (SOP-1422) and Woodland (SOP-1188). The housing, the frame, the lever, the pad's release tabs and the two storage tubes with their caps are this slot: in every one of B5's five pictures the caps and the tube's end in the wing's window are the stock's colour (a cap's O-rings, black on T.REX ARMS' loose one, are inside the housing). B5 names no finish for the polymer but \"Made of MIL-SPEC Materials and Finishes\"; the housing's skin is a fine pebble in its pictures, the lever's smooth."},"buttpad":{"label":"Buttpad","finish":"rubber","recolorable":false,"color":"placeholder-black","follows":{"slot":"body","options":{"fde":{"finish":"rubber","color":"b5-fde-rubber"},"coyote":{"finish":"rubber","color":"b5-coyote-brown-rubber"},"odg":{"finish":"rubber","color":"b5-od-green-rubber"},"wolf":{"finish":"rubber","color":"b5-wolf-grey-rubber"}}},"note":"B5: \"Cushioned Non-slip Buttpad with Built in M4 Multitasker® Tool Holder (tool sold separately)\"; Wing Tactical lists it as \"1x Rubber Buttpad\". The stock's colour on every one: B5's five pictures and Primary Arms' photos show the pad in black, flat dark earth, coyote brown, OD green and wolf grey with the housing, a smooth matte rubber that reads a little lighter than the pebbled housing beside it (most on coyote brown and wolf grey). The black one is a placeholder black: B5's picture has it a charcoal lighter than the housing (#56575a against #353639), Primary Arms' photo the housing's black."},"qd":{"label":"QD socket","finish":"steel","recolorable":false,"color":"placeholder-black","follows":{"slot":"body","options":{"fde":{"finish":"cerakote","color":"b5-fde-steel"},"coyote":{"finish":"cerakote","color":"b5-coyote-brown-steel"},"odg":{"finish":"cerakote","color":"b5-od-green-steel"},"wolf":{"finish":"cerakote","color":"b5-wolf-grey-steel"}}},"note":"B5: \"Fixed Sling Mounts and Steel Anti-rotational QD Mounts\", \"one piece anti-rotation quick disconnect sling mounts\" and \"Color Matched Steel Hardware\"; its picture's callout is OVERMOLDED STEEL ANTI-ROTATIONAL QD MOUNTS. One steel piece through the frame, a socket each side: on the black stock its face round the hole is a dark steel inside the polymer's lip (B5's picture, #444444 against the housing's #353639); on the four colours it is coated in the stock's colour, face and lip alike (B5's and Primary Arms' pictures of each). B5 names neither the steel's black nor the coat: the black is drawn as `steel`, the coloured ones as a matte sprayed coat (`cerakote`, the nearest type the catalog has; it isn't B5's word). The ring drawn takes in the thin polymer lip round the steel."},"pin":{"label":"Lock pin","finish":"steel","recolorable":false,"color":"placeholder-black","follows":{"slot":"body","options":{"fde":{"finish":"cerakote","color":"b5-fde-steel"},"coyote":{"finish":"cerakote","color":"b5-coyote-brown-steel"},"odg":{"finish":"cerakote","color":"b5-od-green-steel"},"wolf":{"finish":"cerakote","color":"b5-wolf-grey-steel"}}},"note":"The lock pin's end under the lever: the stud B5's picture calls COLOR MATCHED STEEL HARDWARE. Black steel on the black stock, coated in the stock's colour on the four others (B5's five pictures, read beside the QD socket's steel: the two are within 13 levels a channel of each other on every colour), drawn as the socket is. The roll pin through its cross hole is bare bright steel on every colour (it shows in B5's coyote and wolf grey pictures and Primary Arms' coyote one) and isn't drawn: a dozen pixels across in B5's 2000 px picture, inside the hole."}},"components":{"body":{"label":"Stock body","material":"body"},"buttpad":{"label":"Buttpad","material":"buttpad"},"qd":{"label":"QD socket","material":"qd"},"pin":{"label":"Lock pin","material":"pin"}},"geometry":{"model":"b5-enhanced-sopmod-stock.glb","components":{},"approximations":["Visual hull of three outlines: B5's own right side photo (turned level by the 0.34° it leans, scaled by its 7.43 x 4.93 in, which fit it within 0.4%) and the back and top views of the design patent its page marks (US D722,357 S: FIG. 2 scaled by 4.93 x 2.4 in, which fit it within 0.5%; FIG. 5 scaled by 7.43 x 2.4 in, within 0.1%). The back view's section holds along the stock wherever the other two show it.","Each wing is a wall round a storage compartment, as the patent's front view draws it: the housing's section moved in by one wall thickness (0.09 in, read at the wings' tips), out from the block under the tube, under the wall drawn across at the axis's height, clear of the bore's own wall. The walls elsewhere are taken to be as thick; beside the bore above the axis the housing is solid. Where each wing tapers to the plate the pad sits on, the compartment breaks through its face: the window B5's photos show there comes of that and isn't traced.","The storage tubes are plain cylinders as wide as the cap B5's side photo shows (0.66 in, a least figure: its upper edge is behind the housing), about each wing tip's own centre, from the pad's plate to where the cap's front stands in that photo; solid, with rounded ends. The caps' ribs, their threads and O-rings aren't drawn, and how long the tubes really are isn't published.","The frame below the housing is a web 0.50 in wide, the width the patent's bottom view gives the strut where its edges run straight; its ribs and recessed panels are flush (no view gives their depth). The strut along its lower edge is the band the side photo shows there (0.09 in thick) and spreads evenly to 1.0 in at the pad's plate, as that bottom view draws it. The block under the tube's front is 0.68 in wide.","The adjustment lever is its side silhouette at the width the patent's bottom view gives it (0.92 in), a slab: its fork round the block and its hollow underside aren't drawn. The lock pin's lower end is a cylinder as wide as the block the side photo shows, a piece of its own under the lever (steel where the lever is polymer: the `pin` slot). The butt pad's release tabs are plain blocks, each as the side photo outlines it, out to the 1.03 in the patent's front view draws across the pair. The QD socket is a ring round its hole standing out of the web to the 0.75 in the patent's bottom view draws across its two faces. The two sling slots, the socket's hole, the hole through the block and the cross hole in the lock pin's end are cut through.","The bore is the circle the patent's front view draws in broken lines (1.161 in: the mil-spec tube's 1.148 and a little), with the indexing rail's channel under it (0.505 in wide, its floor 0.88 below the axis), cut from the front only as far back as the tube's rear end reaches when the stock is collapsed; the mouth's flare isn't drawn. The round hole on the housing's top (0.34 in, over the lock pin) is cut through into it; its size is read from the side only.","Not drawn: the butt pad's diamond face and its border (the patent draws the grid, nothing its depth), the frame's ribs, the row of teeth along the pad's seam, the markings. Edges broken at 0.03 in.","Its seat on the tube is not read from a photo of it on a rifle: its lock pin (5.13 in ahead of the butt in B5's photo) stands in the tube's front hole, ± 0.08 in, which leaves its front 0.21 in behind the castle nut when collapsed."],"ledger":["b5-enhanced-sopmod-stock.length","b5-enhanced-sopmod-stock.height","b5-enhanced-sopmod-stock.width","b5-enhanced-sopmod-stock.tube_axis_below_top","b5-enhanced-sopmod-stock.bore_diameter","b5-enhanced-sopmod-stock.rail_channel_width","b5-enhanced-sopmod-stock.rail_channel_floor_below_axis","b5-enhanced-sopmod-stock.storage_axis_below_top","b5-enhanced-sopmod-stock.storage_axis_off_centre","b5-enhanced-sopmod-stock.wing_tip_radius","b5-enhanced-sopmod-stock.storage_pocket_diameter","b5-enhanced-sopmod-stock.storage_cap_diameter","b5-enhanced-sopmod-stock.storage_cap_front_ahead_of_butt","b5-enhanced-sopmod-stock.top_hole_ahead_of_butt","b5-enhanced-sopmod-stock.top_hole_diameter","b5-enhanced-sopmod-stock.frame_width","b5-enhanced-sopmod-stock.strut_width_at_plate","b5-enhanced-sopmod-stock.strut_flare_start_ahead_of_butt","b5-enhanced-sopmod-stock.block_width","b5-enhanced-sopmod-stock.lever_width","b5-enhanced-sopmod-stock.qd_span","b5-enhanced-sopmod-stock.release_tab_span","b5-enhanced-sopmod-stock.lock_pin_ahead_of_butt","b5-enhanced-sopmod-stock.butt_behind_pin_pos1"]},"profiles":{"side":{"plane":"xy","origin":"rearmost point of the butt pad (x) and the housing's top edge (y), the photo turned so the top is level: the tube axis is parallel to it","offset":{"y":"tube_axis_below_top"},"points":[[0,-0.272],[0.003,-4.675],[0.012,-4.732],[0.05,-4.802],[0.152,-4.88],[0.247,-4.898],[0.469,-4.897],[0.483,-4.878],[0.535,-4.92],[0.676,-4.905],[0.693,-4.86],[0.683,-4.747],[0.694,-4.716],[1.606,-4.069],[3.19,-2.979],[3.194,-3.335],[3.273,-3.422],[3.358,-3.435],[3.443,-3.407],[3.457,-3.378],[3.494,-3.373],[3.56,-3.316],[3.588,-3.316],[3.612,-3.283],[3.64,-3.287],[3.659,-3.254],[3.692,-3.254],[3.715,-3.221],[3.748,-3.221],[3.767,-3.188],[3.795,-3.192],[3.814,-3.159],[3.842,-3.164],[3.87,-3.126],[3.899,-3.13],[3.917,-3.097],[3.95,-3.097],[3.964,-3.068],[3.997,-3.068],[4.021,-3.035],[4.054,-3.035],[4.068,-3.006],[4.101,-3.006],[4.124,-2.973],[4.157,-2.973],[4.171,-2.944],[4.204,-2.944],[4.228,-2.911],[4.256,-2.916],[4.275,-2.883],[4.308,-2.882],[4.331,-2.849],[4.36,-2.854],[4.383,-2.821],[4.416,-2.82],[4.444,-2.782],[4.543,-2.744],[4.623,-2.729],[4.925,-2.728],[4.92,-3.023],[4.946,-3.039],[5.045,-3.043],[5.078,-3.067],[5.187,-3.066],[5.224,-3.042],[5.314,-3.042],[5.345,-3.025],[5.341,-2.73],[5.907,-2.736],[5.954,-2.717],[5.989,-2.681],[6.014,-2.57],[6.515,-2.567],[6.787,-1.997],[6.808,-1.971],[6.856,-1.971],[6.921,-1.88],[6.952,-1.873],[7.017,-1.745],[7.269,-1.211],[7.259,-1.178],[7.445,-0.705],[7.399,-0.077],[7.387,-0.056],[7.273,0],[7.137,-0.01],[5.315,-0.002],[5.225,-0.022],[5.103,-0.022],[4.975,-0.004],[4.668,-0.001],[0.501,-0.007],[0.48,-0.019],[0.473,-0.05],[0.459,-0.003],[0.407,-0.003],[0.19,-0.023],[0.114,-0.052],[0.042,-0.126],[0.014,-0.187]],"features":{"through":[[[1.348,-2.364],[1.348,-2.317],[1.388,-2.263],[1.42,-2.248],[3.162,-2.247],[3.216,-2.287],[3.231,-2.344],[3.212,-2.391],[3.158,-2.427],[1.436,-2.437],[1.367,-2.402]],[[0.947,-3.915],[0.948,-2.636],[0.962,-2.598],[1.016,-2.557],[1.083,-2.566],[1.128,-2.625],[1.126,-3.914],[1.117,-3.942],[1.058,-3.987],[0.992,-3.978]],[[1.598,-3.075],[1.611,-2.99],[1.649,-2.929],[1.698,-2.888],[1.769,-2.864],[1.835,-2.869],[1.911,-2.906],[1.951,-2.951],[1.98,-3.016],[1.98,-3.097],[1.957,-3.158],[1.903,-3.218],[1.828,-3.251],[1.757,-3.251],[1.681,-3.219],[1.626,-3.16]],[[6.237,-2.26],[6.281,-2.191],[6.352,-2.176],[6.397,-2.23],[6.402,-2.282],[6.388,-2.315],[6.325,-2.361],[6.296,-2.361],[6.261,-2.335]],[[5.108,-2.922],[5.113,-2.889],[5.143,-2.873],[5.183,-2.903],[5.153,-2.948],[5.125,-2.944]]],"buttpad":[[[-0.303,0.269],[0.485,0.274],[0.48,-5.201],[-0.27,-5.206]]],"frame":[[[0.664,-1.977],[6.068,-1.978],[6.08,-4.035],[6.033,-4.035],[6.023,-2.431],[6.008,-2.233],[5.941,-2.139],[5.846,-2.102],[4.525,-2.109],[4.384,-2.134],[4.195,-2.215],[3.96,-2.372],[3.725,-2.539],[3.49,-2.729],[3.265,-2.905],[3.195,-2.976],[3.208,-5.279],[0.665,-5.294]]],"strut":[[[0.646,-4.633],[3.194,-2.865],[3.196,-3.25],[0.649,-5.016]]],"lever":[[[3.195,-2.976],[3.265,-2.905],[3.49,-2.729],[3.725,-2.539],[3.96,-2.372],[4.195,-2.215],[4.384,-2.134],[4.525,-2.109],[5.846,-2.102],[5.941,-2.139],[6.008,-2.233],[6.023,-2.431],[6.033,-4.035],[3.201,-4.052]]],"block":[[[6.068,-1.978],[7.686,-1.977],[7.699,-4.026],[6.08,-4.035]]],"pin":[[[4.939,-2.725],[5.355,-2.723],[5.357,-3.067],[4.941,-3.07]]],"tab":[[[0.691,-3.312],[0.898,-3.311],[0.901,-3.802],[0.693,-3.803]]],"qd":[[[1.475,-2.75],[2.103,-2.747],[2.107,-3.37],[1.479,-3.373]]]},"scaleRefs":["b5-enhanced-sopmod-stock.length","b5-enhanced-sopmod-stock.height"],"inputs":{"b5-enhanced-sopmod-stock.height":4.93,"b5-enhanced-sopmod-stock.length":7.43},"tolerance":0.01,"photo":"references/b5-enhanced-sopmod-stock 9bc66a9c7cdd (B5: SOP-1074_PROFILE_RIGHT.png, right side on a transparent ground, 2000 x 2000)","method":"alpha > 0.5, 1 polygons excluded, largest piece, holes filled; rotated +0.3° as declared; scale from b5-enhanced-sopmod-stock.length = 7.43 in (x-extent 1578 px → 212.3 px/in) and b5-enhanced-sopmod-stock.height = 4.93 in (y-extent 1042 px → 211.5 px/in), which agree within 0.4%; mean 211.9 px/in; origin at x min, y max of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 100 points (IoU 0.998 with the full outline); features through the same placement (through: reviewed pixel boxes; buttpad: reviewed pixel boxes; frame: reviewed pixel boxes; strut: reviewed pixel boxes; lever: reviewed pixel boxes; block: reviewed pixel boxes; pin: reviewed pixel boxes; tab: reviewed pixel boxes; qd: reviewed pixel boxes) (tools/trace.py)","via":"harvest","note":"The two sling slots, the QD socket's hole, the hole through the block and the cross hole in the lock pin's end are cut through. The lever and the lock pin's end are in the outline; the storage tube's cap is taken out of it. The pad's release tab is a feature. The frame's ribs, its recessed panels, the window where each wing tapers to the pad and the markings aren't."},"rear":{"plane":"zy","origin":"the top edge, centred: as the side profile, offset down to the tube axis","offset":{"y":"tube_axis_below_top"},"points":[[-1.203,-1.516],[-1.16,-1.679],[-1.09,-1.788],[-0.975,-1.882],[-0.823,-1.935],[-0.747,-2.015],[-0.75,-4.216],[-0.711,-4.41],[-0.655,-4.538],[-0.591,-4.633],[-0.43,-4.783],[-0.313,-4.851],[-0.193,-4.893],[0.044,-4.918],[0.182,-4.897],[0.288,-4.861],[0.405,-4.801],[0.501,-4.73],[0.64,-4.562],[0.729,-4.357],[0.754,-4.138],[0.75,-2.011],[0.826,-1.935],[0.9,-1.918],[1,-1.868],[1.107,-1.767],[1.189,-1.605],[1.203,-1.438],[1.15,-1.261],[0.517,-0.232],[0.43,-0.149],[0.303,-0.067],[0.154,-0.014],[-0.002,0],[-0.062,0],[-0.203,-0.028],[-0.334,-0.085],[-0.455,-0.17],[-0.538,-0.26],[-1.139,-1.244],[-1.192,-1.378]],"scaleRefs":["b5-enhanced-sopmod-stock.height","b5-enhanced-sopmod-stock.width"],"inputs":{"b5-enhanced-sopmod-stock.height":4.93,"b5-enhanced-sopmod-stock.width":2.4},"tolerance":0.01,"photo":"references/b5-enhanced-sopmod-stock f2d5af41858b (US D722,357 S, sheet 2 of 8, FIG. 2 back view, 300 dpi)","method":"luminance < 128, inside [440, 900, 1210, 2380], closing ×18, holes filled, inset 2 px (half the outline's stroke); scale from b5-enhanced-sopmod-stock.height = 4.93 in (y-extent 1390 px → 281.9 px/in) and b5-enhanced-sopmod-stock.width = 2.4 in (x-extent 680 px → 283.3 px/in), which agree within 0.5%; mean 282.6 px/in; origin at x center, y max of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 41 points (IoU 0.997 with the full outline) (tools/trace.py)","via":"harvest","note":"Seen from the rear, upright on the sheet: the butt pad's stadium, 1.50 in wide, and over it the housing, a triangle with a round top about the tube and a round tip each side about a storage tube; symmetric."},"plan":{"plane":"xz","origin":"the butt pad's rear, centred","offset":{},"points":[[0,0.44],[0,0],[0,-0.433],[0.053,-0.617],[0.146,-0.714],[0.266,-0.749],[0.731,-0.749],[1.503,-1.196],[7.017,-1.2],[7.091,-1.196],[7.141,-1.172],[7.431,-0.8],[7.431,0.803],[7.16,1.156],[7.077,1.2],[1.506,1.2],[0.721,0.745],[0.248,0.749],[0.171,0.728],[0.104,0.685],[0.046,0.603]],"scaleRefs":["b5-enhanced-sopmod-stock.length","b5-enhanced-sopmod-stock.width"],"inputs":{"b5-enhanced-sopmod-stock.length":7.43,"b5-enhanced-sopmod-stock.width":2.4},"tolerance":0.01,"photo":"references/b5-enhanced-sopmod-stock 9c24cfbcc0fb (US D722,357 S, sheet 4 of 8, FIG. 5 top view, 300 dpi)","method":"luminance < 128, inside [880, 530, 1650, 2720], closing ×18, holes filled, inset 2 px (half the outline's stroke); rotated +90.0° as declared; scale from b5-enhanced-sopmod-stock.length = 7.43 in (x-extent 2109 px → 283.8 px/in) and b5-enhanced-sopmod-stock.width = 2.4 in (y-extent 681 px → 283.8 px/in), which agree within 0.0%; mean 283.8 px/in; origin at x min, y center of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 21 points (IoU 0.999 with the full outline) (tools/trace.py)","via":"harvest","note":"The sheet has the butt at the top. Symmetric: the pad narrower than the housing, the wings spreading from the plate the pad sits on to their full width 1.5 in ahead of the butt, the front corners broken."}},"gaps":[{"what":"Its seat on the tube from a photo (it is seated by its lock pin in the tube's front hole, ± 0.08 in)","need":"a straight side photo of it on a lower with both receiver pins in view, at any position (the sellers' photos of it installed are oblique or 800 px wide)"},{"what":"How light B5's colours are: its own pictures, which the five are matched on, are darker than every seller's photo of the same stock (flat dark earth #786f62 on the lever's flat, against #a69d8e in Primary Arms' photo and #c1b197 in Wing Tactical's; the blacks agree)","need":"a photo of a coloured stock beside a black one and a grey card, or on a rifle whose black parts set the exposure"},{"what":"What the steel hardware's black and its coloured coat are (B5 says only \"Color Matched Steel Hardware\"), and whether the black pad is the housing's black or a charcoal","need":"B5's or a seller's words for the finish; a photo of the black stock's pad beside its housing in flat light"},{"what":"How deep the butt pad's diamond pattern is, and how far the frame's panels are recessed inside their ribs","need":"a view that shows their depth, or an oblique photo with the camera fitted to it"},{"what":"The storage tubes' own size, their caps' ribs and the walls' thickness away from the wings' tips","need":"the maker's drawing, or a photo square into the stock's front with a scale in its plane (T.REX ARMS' and Wing Tactical's are oblique)"},{"what":"The round hole on the top from above (its size is read from the side only, ± 0.04 in)","need":"a photo from straight above"},{"what":"A weight measured on a scale (B5 says 12.2 oz, its shop table 12, two sellers 11.8, which is its other SOPMOD's figure, one seller 14.4, a 2012 weighing 11.5)","need":"a reviewer's weighing of the current stock, with the method"}]},"b5-type-23-p-grip":{"id":"b5-type-23-p-grip","name":"Type 23 P-Grip","manufacturer":"B5 Systems","sku":"PGR-1122","url":"https://b5systems.com/collection/ar/p-grip-23/","category":"grip","description":"B5's more upright grip: \"an increased vertical grip angle and extended tang to improve ergonomics and ensure proper trigger index\". Its front strap leans 13 degrees, its back strap 19; the block's front face runs straight down 1.3 in behind the trigger guard, a beavertail rises behind, and each side has a panel of B5's aggressive texture with a band of it down the front strap. Hollow from below for B5's grip plug, sold separately.","weight":"b5-type-23-p-grip.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"grip_lug":{"origin":["-{.seat_x}",0,0],"note":"Grip frame: origin at the rear end of its flat top, which bears on the lower's underside. The anchor is the point of that top at the takedown pin's x once installed (seat_x)."}},"interfaces":{"grip_lug":{"type":"ar15.grip_lug","role":"grip","anchor":"grip_lug","params":{},"flips":false}},"materials":{"body":{"label":"Grip","finish":"polymer","recolorable":true,"color":"placeholder-polymer-black","sheen":"satin","options":{"black":{"label":"Black","finish":"polymer","color":"placeholder-polymer-black","sheen":"satin","sku":"PGR-1122","source":"https://b5systems.com/collection/ar/p-grip-23/"},"fde":{"label":"Flat Dark Earth","finish":"polymer","color":"b5-fde","sheen":"satin","sku":"PGR-1120","source":"https://b5systems.com/collection/ar/p-grip-23/"},"coyote":{"label":"Coyote Brown","finish":"polymer","color":"b5-coyote-brown","sheen":"satin","sku":"PGR-1126","source":"https://b5systems.com/collection/ar/p-grip-23/"},"odg":{"label":"OD Green","finish":"polymer","color":"b5-od-green","sheen":"satin","sku":"PGR-1134","source":"https://b5systems.com/collection/ar/p-grip-23/"},"wolf":{"label":"Wolf Grey","finish":"polymer","color":"b5-wolf-grey","sheen":"satin","sku":"PGR-1118","source":"https://b5systems.com/collection/ar/p-grip-23/"}},"default":"black","note":"B5's five solid colours by the name and number its page's variation data gives each (Black PGR-1122, Flat Dark Earth PGR-1120, Coyote Brown PGR-1126, OD Green PGR-1134, Wolf Grey PGR-1118), each one colour all over in B5's own picture of it (PGR-<number>_PROFILE_RIGHT.png), the texture panel and the strap's band included: the same series and light as B5's stocks', whose four colours are matched on it (data/colors/b5-systems.yaml; the grip's smooth flat under the block, square to the camera, reads #6e665a, #66563e, #464636 and #464646 in B5's four pictures (tools/color_sample.py, [760, 360, 900, 520]), 8 to 28 levels a channel darker than the stocks' lever flat in each colour and the same hue, as their housings read darker; its black #343437 is the stocks' #36373a). \"Available in All Standard Colors\". The black is the catalog's placeholder polymer black, as on B5's stocks. Sold too and not offered, a printed pattern being no one colour: MultiCam® (PGR-1135), MultiCam® Black (PGR-1426) and Woodland (PGR-1187), $29 each. B5: \"Made of MIL-SPEC Material\"; Primary Arms: \"Material Polymer\"."},"texture":{"label":"Texture panels","finish":"polymer","recolorable":true,"color":"placeholder-polymer-black","sheen":"matte","detail":"stipple","follows":{"slot":"body","options":{"fde":{"finish":"polymer","color":"b5-fde","sheen":"matte"},"coyote":{"finish":"polymer","color":"b5-coyote-brown","sheen":"matte"},"odg":{"finish":"polymer","color":"b5-od-green","sheen":"matte"},"wolf":{"finish":"polymer","color":"b5-wolf-grey","sheen":"matte"}}},"note":"B5: \"Aggressive Texture for Increased Retention\". The panel on each side inside its groove, and the band down the front strap ahead of the strap's groove (B5's two side pictures; Sportsman's photo of the black one from ahead and the right): the grip's own colour in every colourway, with a coarse texture where the rest is smooth. Drawn as the generated stipple on the same colour."}},"components":{"body":{"label":"Grip","material":"body"},"texture":{"label":"Texture panels","material":"texture"}},"geometry":{"model":"b5-type-23-p-grip.glb","components":{},"approximations":["Built about its straps' mean axis from B5's own square side picture (the right; the left traced as a check: the two outlines agree to IoU 0.984), scaled by B5's Length and Height, which are that picture's two extents at one scale (0.3% apart). Its section, square to the axis, is a rounded rectangle from the back strap to the front strap: B5's 1.26 in across the body from the texture panel's top down to the base, the block's width (the receiver's 0.88, as B5's installation drawing has the walls rising into the receiver's sides) from the shoulder up, widening between over an assumed 0.4 in. Its corners' radii are assumed (0.45 in at the back strap, which a photo from behind has nearly half round; 0.25 at the front strap, flatter in a photo from ahead): no view on file is square to a section, the grip's front, back or base.","The texture: on each side the panel inside a groove where B5's pictures have its rim, and the band down the front strap ahead of the groove the pictures show beside it; each groove 0.039 in wide (twice the strap groove's shadow on B5's picture) and an assumed 0.02 deep, swept along the surface. The panel and the band are the texture slot, drawn stippled; whether the panel stands proud of the side or lies in it isn't seen (Sportsman's photo has its rim as a lit line).","The top is cut for the receiver (lib.grip_receiver_cuts, as every grip's is): the slot for the standard lug, an assumed 0.405 in across (no view on file looks at the top square: between BCM's 0.385 and Magpul's 0.425), open through the block's front above the tang's foot, and under the receiver's rear the round of a standard receiver's underside, which hollows the beavertail between its two rails.","Not drawn: the hollow inside the top (two walls and the webs between them, as the manual's FIG 1 and Rifle Supply's photos have it, all under the receiver once installed), the screw's hole and the detent spring's hole, the hollow the grip plug goes into under the base (no view of the base on file), the B5 SYSTEMS lettering on the block. The block's and the beavertail's edges are as the outline and the section give them.","Seated by its interface, not by a photo of it installed: the block's front face against the rear of the trigger guard's ears, where the Army drawing ends the lug, as BCM's Mod 3 is; its flat top on the receiver's underside. Below the ears the face goes on down to the tang's foot, 1.3 in below the top, behind the trigger guard's rear end."],"ledger":["b5-type-23-p-grip.length","b5-type-23-p-grip.height","b5-type-23-p-grip.thickness","b5-type-23-p-grip.grip_angle","b5-type-23-p-grip.front_strap_lean","b5-type-23-p-grip.back_strap_lean","b5-type-23-p-grip.bottom_below_lower_underside","b5-type-23-p-grip.block_front_x","b5-type-23-p-grip.seat_x","b5-type-23-p-grip.top_block_width","b5-type-23-p-grip.lug_slot_width","b5-type-23-p-grip.shoulder_length","b5-type-23-p-grip.back_strap_round","b5-type-23-p-grip.front_strap_round","b5-type-23-p-grip.groove_width","b5-type-23-p-grip.groove_depth","std.ar15.grip_lug_width","std.ar15.grip_lug_face_from_pin","std.ar15.grip_lug_face_angle","std.ar15.grip_lug_depth","std.ar15.grip_seat_below_deck","std.ar15.rear_underside_arc_r_fullest","std.ar15.rear_underside_round_r","std.ar15.lower_body_width"]},"profiles":{"side":{"plane":"xy","origin":"rear end of the grip's flat top, which bears on the receiver's underside (the grip frame origin)","offset":{},"points":[[-1.493,-3.664],[-1.493,-3.708],[-1.479,-3.747],[-1.438,-3.788],[-1.302,-3.827],[-0.952,-3.91],[-0.539,-3.992],[-0.5,-3.992],[-0.389,-4.021],[-0.374,-4.016],[-0.359,-4.026],[-0.223,-4.046],[-0.029,-4.089],[0.267,-4.138],[0.355,-4.118],[0.401,-4.077],[0.415,-4.033],[0.381,-4.014],[0.391,-3.975],[0.403,-3.963],[0.447,-3.953],[0.469,-3.917],[0.474,-3.839],[0.488,-3.82],[0.493,-3.761],[0.503,-3.747],[0.503,-3.698],[0.522,-3.664],[0.532,-3.592],[0.546,-3.558],[0.542,-3.533],[0.556,-3.509],[0.556,-3.48],[0.571,-3.46],[0.571,-3.417],[0.585,-3.392],[0.58,-3.368],[0.595,-3.339],[0.619,-3.208],[0.648,-3.14],[0.648,-3.111],[0.673,-3.033],[0.673,-2.994],[0.692,-2.941],[0.702,-2.853],[0.726,-2.79],[0.726,-2.756],[0.745,-2.717],[0.741,-2.688],[0.755,-2.664],[0.75,-2.64],[0.77,-2.61],[0.77,-2.572],[0.794,-2.494],[0.799,-2.436],[0.833,-2.338],[0.833,-2.314],[0.847,-2.295],[0.843,-2.28],[0.862,-2.232],[0.872,-2.149],[0.901,-2.062],[0.901,-2.028],[0.93,-1.945],[0.93,-1.911],[0.949,-1.872],[0.945,-1.848],[0.954,-1.833],[0.906,-1.795],[0.915,-1.751],[0.928,-1.739],[0.952,-1.744],[0.964,-1.731],[0.959,-1.717],[0.974,-1.683],[0.998,-1.552],[1.042,-1.455],[1.112,-1.37],[1.217,-1.299],[1.226,-1.265],[1.241,-0.24],[1.226,-0.182],[1.202,-0.134],[1.144,-0.066],[1.088,-0.029],[1.005,-0.005],[0.005,0.005],[-0.007,0.017],[-0.061,0.168],[-0.124,0.279],[-0.206,0.386],[-0.364,0.529],[-0.539,0.627],[-0.622,0.656],[-0.777,0.685],[-0.787,0.695],[-0.942,0.695],[-0.952,0.685],[-0.996,0.68],[-1.022,0.648],[-1.037,0.61],[-1.037,0.036],[-1.022,0.007],[-0.986,-0.029],[-0.923,-0.058],[-0.889,-0.058],[-0.826,-0.078],[-0.714,-0.136],[-0.653,-0.187],[-0.576,-0.274],[-0.522,-0.367],[-0.474,-0.498],[-0.464,-0.644],[-0.474,-0.731],[-0.503,-0.838],[-0.629,-1.163],[-1.105,-2.494],[-1.484,-3.655]],"features":{"panel":[[[-0.282,-1.27],[0.753,-1.416],[0.136,-3.975],[-1.044,-3.766]]],"strap_groove":[[[0.845,-1.795],[0.864,-1.795],[0.34,-3.941],[0.321,-3.941]]]},"scaleRefs":["b5-type-23-p-grip.height","b5-type-23-p-grip.length"],"inputs":{"b5-type-23-p-grip.height":4.84,"b5-type-23-p-grip.length":2.73},"tolerance":0.006,"photo":"references/b5-type-23-p-grip 0e18f2708bff (B5's PGR-1122_PROFILE_RIGHT (2024/12): the black grip's right side square on, its flat top level, 1400 x 1400 on a transparent ground)","method":"alpha > 0.5, closing ×2, largest piece, holes filled; scale from b5-type-23-p-grip.height = 4.84 in (y-extent 995 px → 205.6 px/in) and b5-type-23-p-grip.length = 2.73 in (x-extent 563 px → 206.2 px/in), which agree within 0.3%; mean 205.9 px/in; origin at the rear end of the flat top; Douglas-Peucker at 0.006 in with the extremes kept: 118 points (IoU 0.997 with the full outline); features through the same placement (panel: the texture panel's rim, its four corners picked on a gridded crop (.cache/batch14/b5-type-23-p-grip/grid-panel.png): the lit line round the panel in Sportsman's photo; strap_groove: the groove between the side and the front strap's band of texture, its two ends picked on the same crop (a dark line 4 px wide)) (tools/trace.py)","via":"harvest","note":"The outline includes the beavertail (behind and above the flat top; it tucks under the receiver's rear) and the block's front face, which runs straight down 1.3 in to the tang's foot (B5: an \"extended tang\"). The texture panel and the strap's band are features, not the outline."}},"gaps":[{"what":"The grip's section: how wide it is down its length, and how its straps round across","need":"a straight view of the grip from behind (square to the back strap), from the front and from below, from 8 ft or more; or a drawing or design patent of B5's for it (no patent marking page of B5's was looked for)"},{"what":"The lug slot's width, and the top's shape under the receiver","need":"a view of the grip's top from straight above with a scale, or the slot against the top's width in one"},{"what":"Its seat read on the grip installed (it is seated by its interface)","need":"a straight side photo of a Type 23 on a lower with the receiver's pins in view"},{"what":"The hollow under the base that B5's grip plug goes into","need":"a view of the base from below"},{"what":"Whether B5's 2.20 oz takes in the T30 screw","need":"B5's word, or a weighing of the grip with and without it"}]},"bad-workhorse-lower":{"id":"bad-workhorse-lower","name":"Workhorse stripped lower","manufacturer":"Battle Arms Development","sku":"WH556-LR","category":"lower","description":"Forged, TDP-compatible lower with a set-screw bolt catch pin, captured takedown detent and tension screw. Also made in ODG. Modelled from its traced side outline at the Army drawing's widths, with the inside a forged mil-spec lower shows (D46): the fire-control pocket, the magazine well open through, the tower bored for the receiver extension and the pivot lug slotted for an upper's lug.","weight":"bad-workhorse-lower.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"pins":{"origin":[0,0,0],"note":"The rifle frame origin."},"buffer_tube_mount":{"origin":[0,"{.buffer_axis_above_pin}",0],"x":[-1,0,0]},"magwell":{"origin":["{.magazine_seat_x}","{std.ar15.mag_catch_slot_bottom_y} + {std.ar15.mag_catch_slot_h}",0],"note":"Where a seated magazine hangs: x where its spine's rear face sits in the well (magazine_seat_x), y at the catch's upper face, which is the top of the slot the catch comes through (the Army's drawing). A magazine's own anchor is the upper edge of its catch notch, so each hangs by its own. Until 2026-10-05 this was the feed lips' top of a seated Black Dog (magazine_seat_y, still in the ledger as that), and a PMAG, whose notch is 0.37 in nearer its top, hung that much too high: its lips above the bore. Magazines seat square to the bore (std.ar15.magwell_wall_lean); the lip's slope (magwell_bottom_angle) is geometry of the lip. M2 hung magazines from the magwell bottom's center (magwell_bottom_center_*) by their measured hang; M3 put a Sonic X's frame origin where the user's flat-lay has it."},"grip_lug":{"origin":[0,"{.grip_seat_y}",0],"note":"The grip mount's datum: the receiver's underside behind the step, where a grip's flat top bears, at the takedown pin's x. Each grip says where its own origin sits from here (its seat_x, from a pin-framed photo of it installed: M6). M2 used the bottom of the step behind the tang (grip_shelf_top), 0.47 in lower."},"trigger_guard":{"origin":["{.trigger_guard_front_x}","{.trigger_guard_front_y}",0],"x":["{.trigger_guard_front_x} - {.trigger_guard_rear_x}","{.trigger_guard_front_y} - {.trigger_guard_rear_y}",0],"note":"At the front ear hole, with the guard's x axis through the rear ear hole: a guard pins into both."},"fcg":{"origin":["{.trigger_pin_x}","{.trigger_pin_y}",0],"note":"Trigger pin axis."},"lpk":{"origin":[0,0,"-{std.ar15.lower_body_width} / 2"],"note":"The body's left face (the TDP's width), level with the takedown pin: the controls' heads seat on it."},"selector":{"origin":["{std.ar15.selector_x}","{std.ar15.selector_y}",0],"note":"The selector's hole (the Army's drawing 8448608), on its axis at the receiver's mid-plane: a selector chosen on its own turns here (D86), its levers' inner faces on the body's two sides."}},"interfaces":{"receiver_pins":{"type":"ar15.upper_lower","role":"lower","anchor":"pins","params":{"pin_spacing":"={std.ar15.pin_spacing}"},"flips":false},"buffer_tube_mount":{"type":"ar15.buffer_tube_mount","role":"receiver","anchor":"buffer_tube_mount","params":{},"flips":false},"magwell":{"type":"ar15.magwell","role":"receiver","anchor":"magwell","params":{"family":"5.56"},"flips":false},"grip_lug":{"type":"ar15.grip_lug","role":"receiver","anchor":"grip_lug","params":{},"flips":false},"trigger_guard":{"type":"ar15.trigger_guard","role":"receiver","anchor":"trigger_guard","params":{},"flips":false},"fcg":{"type":"ar15.fcg","role":"receiver","anchor":"fcg","params":{"pin_diameter":"small-pin"},"flips":false},"lpk":{"type":"ar15.lpk","role":"receiver","anchor":"lpk","params":{},"flips":false},"selector":{"type":"ar15.selector","role":"receiver","anchor":"selector","params":{},"flips":false}},"materials":{"receiver":{"label":"Receiver","finish":"anodized","recolorable":true,"color":"placeholder-black","sheen":"matte","options":{"black":{"label":"Black Anodized","finish":"anodized","color":"placeholder-black","sheen":"matte","sku":"WH556-LR-BLK","source":"https://battlearmsdevelopment.com/shop/wh556-lr-blk-workhorse-forged-7075-t6-lower-receiver-stripped-black-anodized-ar15-956"}},"default":"black","note":"BAD's words: \"MIL-A-8625F, Type III, Hard Anodized Flat Black\". BAD also sells it \"MIL-A-8625F, Type III, Hard Anodized ODG\" (WH556-LR-ODG, https://battlearmsdevelopment.com/shop/wh556-lr-odg-workhorse-forged-7075-t6-lower-receiver-stripped-odg-anodized-ar15-958): not offered here, because no photograph of that anodize is on file. The one image on its page is a black receiver's photo tinted green (it is marked MDL: BAD-15, its highlights are the black one's, and the ODG upper's two pictures are tinted a yellower olive): fitted to it, the receiver drew a light yellow green that no olive drab anodize is (2026-10-06). The black is unmatched (sealed black anodize)."}},"components":{"receiver":{"label":"Receiver","material":"receiver"}},"geometry":{"model":"bad-workhorse-lower.glb","components":{},"approximations":["The traced outline at the TDP's body width (0.880), its magazine well's walls at 1.098 from each side's measured rear edge forward (on the left from the curved edge the left photo shows: back to 2.95 above the catch's slot), and the buffer tower's ring at 1.392 about the buffer axis. The outline is the right-side photo read through a camera fitted to it (2026-10-05): the photo was taken from 24 in with the lens level with the trigger guard and the receiver leaning 9 degrees, so each stretch is read at the depth of the edge that shows there (the lug on its near side, the seat on the far edge of its flat, the ears' rear on the near ear and the trigger opening on the far one). Below the pin line it is good to about 0.01 in: what the camera's lean leaves open.","Below the face a grip's top bears on, what a forging has there (2026-10-05): the lug a grip's slot goes over at the Army drawing's .375 (8448608 sheet 2, View R-R), the walls behind and ahead of the trigger with the guard's ears 0.659 across (the reference CAD model's) and the ears .442 apart (the drawing's .438 +.008) from the lug's bottom flat down, the front pair's gap open into the well's rear; and the rear underside, from under the tower to that face, a half-round across the body (the model's), along the outline's own line, so the face's rear edge is a U. Where the lug and the ears begin is the outline's own: the ears' rear face on the drawing's (1.175 from the takedown pin), the lug's sloped face and bottom flat on the drawing's too, and the lug's rear face 0.20 in ahead of the drawing's, which is the Workhorse's own (both photos have it there). Until 2026-10-05 the outline was traced in a frame set by the two pins alone, which read everything below them large: the ears were drawn 0.045 behind the drawing's and the seat 0.027 low, and a grip's nose made to stop at the drawing's ears stood 0.03 in into them. The walls step in square at the face's level, where the model flares them over 0.15 in. Until then the outline was one slab of the body's width, and a grip's top stood in the lug.","The inside a forged mil-spec lower has, from the Army's drawing 8448608 (D46): the fire-control pocket (.690 wide, 2.87 long, 1.249 deep, its corners .218 R: the rear two as the front's, which the drawing doesn't dimension), the rear lug's .500 slot, the safety detent's boss (drawn square where the drawing ramps its front end), the trigger slot and the magazine well with its spine slot, open from the deck to the mouth.","The tower's ring is bored through for the receiver extension (2026-10-05; it was a solid plug) at the mil-spec extension's OD, 1.148 in: the thread it really has is larger by its depth, which isn't on file. The bore runs on forward as the trough between the walls' sweep until it runs out above the deck (both photos look into it). Those two walls rise from the deck to the ring's front face along the Army drawing's arc (.750 R, 8448608 sheet 1: 2026-10-12) and no higher: the outline there is the far wall and the ring's threads seen through its front, from a lens that stood ahead of the tower, and until then the walls were drawn to it, up to the ring's top a fifth of an inch ahead of its face. Its deck, from just behind the takedown pin to where its top turns down at the pivot lug, is the Army drawing's plane (.250 -.003 above the pins: std.ar15.deck_y), not the outline's own top edge, which reads a hundredth off it and not level (2026-10-12): the deck is the seat every upper sits on. And the pivot lug is two ears with the slot an upper's front lug goes in between them (it was a solid block, and every upper's lug stood in it): the Army drawing's .500 (Section C-C), cut through the lug ahead of the well's front face and from the lug's underside up. How far down the slot is cut into the well's front wall isn't on file: the wall is left whole between the ears.","The holes its photos show open (2026-10-03), at the drawing's sizes (sheet 1) and the Workhorse's places: the takedown and pivot pins' .251, the selector's .376, the hammer's and trigger's .1560, the trigger guard's .1275 roll pin hole through both ears and its front .125 hole in the right ear from a .250 spotface; the takedown hole's .44 spotface on the right only, as the photos and the reference CAD model have it (the drawing calls for both sides). On the left, the magazine catch's slot (the drawing's, its floor the CAD model's) opening into the well, with the catch hole through to the counterbore; the band down the well's wall and the round boss the slot runs through (the CAD model's, both on the left photo); the bolt catch's slot below the bosses and its plunger's hole (the drawing's front and width, the model's end and depths).","Not drawn: the bore's thread and the buffer retainer's hole, the pivot hole's .27 countersink, the pivot detent's .078 hole, where the bolt catch's slot goes through the wall at the deck (its depth isn't read), the grip screw's tapped hole in the lug, the small blind hole in the roll level with the pivot pin, and on the right side the rib that runs down from the roll beside the magazine catch's fence to a point, with the ridge round the fence (the forging's own, not in the drawing or the reference model: their outlines are on the right photo, but how far they stand off the walls' face can't be read from a side view, and the one oblique on file looks along them from above; a view from the muzzle end or from below would give it).","The bolt catch's two bosses on the left from the left photo (their outlines) out to the TDP's face (0.618 from the centre, Section C-C).","The magazine catch's fence: its flat face where the right photo has it, out to the magazine well walls' face (the reference CAD model the user chose as a source has the fence and the walls as one plane; through a camera fitted to the oblique right photo the pocket's mouth is 0.543 in from the centre, the walls' 0.549), run on forward into the wall and up under the roll (2026-10-05: as an island it left the body showing as a groove 0.05 in wide where the photo has a rib), its rear and lower sides rounded where the photo shows slopes; the button's pocket and the catch hole's counterbore from that model.","The roll along the top of the well's right wall (2026-10-05), the forging's own and the widest thing on the receiver: a half-round bar from above the fence's rear (X 2.905) to a flat end beside the pivot lug (6.231, where the Army's pivot pin has the flat on its head), its top the deck's edge, its lower edge 0.204 in below the pin line, its crest 0.80 in from the centre: 0.25 in proud of the wall. The crest is read on the one oblique of the right side on file (a small hole in the roll, through a camera fitted to the drawing's holes and the deck's edges: ± 0.04), and the one published width agrees (a seller's 1.5 in: this roll and the left side's 0.70). Drawn as half an ellipse through the three places read, which leaves its top level with the deck for its first few hundredths where the photos have it turning down at once; its rear end rounded over the 0.19 in the photo shows. It meets the wall under it at a crease where the part blends into the wall. The kit's pivot pin head is drawn with its flat (the Army's drawing 8448621) toward the roll's front end, a hair clear of it.","The well's flared lip and the takedown lugs' ears are drawn at those widths: their own aren't dimensioned on the TDP's sheets.","Edges broken at 0.02 in (the drawing's \"break corners .02 R\"); markings and roll marks aren't drawn."],"ledger":["std.ar15.lower_body_width","std.ar15.grip_lug_width","std.ar15.trigger_guard_ears_width","std.ar15.trigger_guard_ear_gap","std.ar15.rear_underside_round_r","bad-workhorse-lower.grip_seat_y","std.ar15.fcg_pocket_front_x","std.ar15.fcg_pocket_depth","std.ar15.magwell_front_inner_x","std.ar15.magwell_outside_width","std.ar15.buffer_tower_od","std.receiver_extension.milspec_od","std.ar15.front_lug_slot_width","bad-workhorse-lower.well_roll_crest_out","bad-workhorse-lower.well_roll_bottom_y","bad-workhorse-lower.well_roll_rear_x","bad-workhorse-lower.well_roll_front_x","bad-workhorse-lower.width","bad-workhorse-lower.magwell_wall_rear_x","bad-workhorse-lower.magwell_wall_rear_x_left","bad-workhorse-lower.magwell_wall_upper_rear_x_left","std.ar15.takedown_hole_d","std.ar15.selector_hole_d","std.ar15.fcg_pin_hole_d","std.ar15.mag_catch_slot_rear_x","std.ar15.mag_catch_slot_floor","std.ar15.mag_catch_boss_x","std.ar15.magwell_band_rear_x","std.ar15.bolt_catch_slot_front_x","std.ar15.bolt_catch_boss_out","bad-workhorse-lower.bolt_catch_boss_rear_x","bad-workhorse-lower.bolt_catch_boss_front_x","std.ar15.pin_spacing","bad-workhorse-lower.buffer_axis_above_pin","bad-workhorse-lower.magwell_bottom_center_x","bad-workhorse-lower.magwell_bottom_center_y","bad-workhorse-lower.magwell_bottom_angle"]},"profiles":{"side":{"plane":"xy","origin":"the takedown pin centre (the rifle frame origin), +x toward the muzzle","offset":{},"points":[[-1.159,0.335],[-1.121,-0.207],[-1.13,-0.533],[-0.853,-0.558],[-0.645,-0.653],[-0.49,-0.783],[-0.403,-0.903],[-0.341,-1.043],[-0.307,-1.071],[0.12,-1.067],[0.131,-1.454],[0.174,-1.513],[0.975,-1.977],[1.039,-2.002],[1.172,-2.008],[1.175,-2.323],[1.203,-2.357],[1.615,-2.365],[1.668,-2.318],[1.687,-2.274],[1.679,-2.204],[1.528,-2.059],[1.462,-1.971],[1.395,-1.831],[1.366,-1.704],[1.381,-1.501],[1.43,-1.373],[1.492,-1.277],[1.642,-1.151],[1.85,-1.064],[2.948,-1.061],[3.072,-1.112],[3.24,-1.226],[3.325,-1.334],[3.389,-1.483],[3.403,-1.545],[3.392,-1.781],[3.325,-1.947],[3.169,-2.155],[3.177,-2.243],[3.196,-2.28],[3.275,-2.344],[3.381,-2.368],[3.771,-2.283],[5.095,-2.041],[6.144,-1.873],[6.178,-1.833],[6.179,-1.766],[6.112,-1.68],[6.082,-1.588],[6.085,-0.661],[6.099,-0.543],[6.153,-0.418],[6.239,-0.315],[6.423,-0.226],[6.547,-0.122],[6.573,-0.065],[6.58,0.023],[6.537,0.117],[6.484,0.171],[6.434,0.196],[6.198,0.211],[6.141,0.236],[0.189,0.241],[-0.027,0.259],[-0.149,0.309],[-0.276,0.439],[-0.35,0.566],[-0.408,0.756],[-0.433,1.12],[-0.495,1.467],[-0.591,1.54],[-0.629,1.553],[-0.961,1.552],[-1.069,1.526],[-1.103,1.497],[-1.125,1.426],[-1.13,1.333],[-1.124,0.6]],"scaleRefs":["std.ar15.lower_body_width","std.ar15.takedown_spotface_depth","std.ar15.pin_spacing","bad-workhorse-lower.selector_x","bad-workhorse-lower.trigger_pin_x","bad-workhorse-lower.trigger_pin_y","bad-workhorse-lower.hammer_pin_x","bad-workhorse-lower.hammer_pin_y","bad-workhorse-lower.trigger_guard_rear_x","bad-workhorse-lower.trigger_guard_rear_y","std.ar15.trigger_guard_ears_width","bad-workhorse-lower.trigger_guard_front_x","bad-workhorse-lower.trigger_guard_front_y","std.ar15.trigger_guard_front_spotface_floor","std.ar15.grip_lug_width","std.ar15.rear_underside_round_r","std.ar15.buffer_tower_od","std.ar15.magwell_outside_width","bad-workhorse-lower.buffer_axis_above_pin"],"inputs":{"bad-workhorse-lower.buffer_axis_above_pin":0.8775,"bad-workhorse-lower.hammer_pin_x":2.771,"bad-workhorse-lower.hammer_pin_y":-0.375,"bad-workhorse-lower.selector_x":0.803,"bad-workhorse-lower.trigger_guard_front_x":3.3425,"bad-workhorse-lower.trigger_guard_front_y":-2.18,"bad-workhorse-lower.trigger_guard_rear_x":1.4985,"bad-workhorse-lower.trigger_guard_rear_y":-2.18,"bad-workhorse-lower.trigger_pin_x":1.928,"bad-workhorse-lower.trigger_pin_y":-0.689,"std.ar15.buffer_tower_od":1.392,"std.ar15.grip_lug_width":0.375,"std.ar15.lower_body_width":0.88,"std.ar15.magwell_outside_width":1.098,"std.ar15.pin_spacing":6.375,"std.ar15.rear_underside_round_r":0.44,"std.ar15.takedown_spotface_depth":0.04,"std.ar15.trigger_guard_ears_width":0.659,"std.ar15.trigger_guard_front_spotface_floor":0.3219},"tolerance":0.01,"photo":"references/bad-workhorse-lower 3f26be6b7eb5 (right side, Arsenal Engineering copy of the BAD photo)","method":"distance from the border's background colour, largest piece, holes filled; a pinhole camera fitted to the rims of 7 holes, 5 of them with the far rim seen through the near one (takedown, pivot, trigger, hammer, guard_rear, guard_front at the ledger's places; selector (its y left to the fit)): lens 24.1 ± 0.9 in from the centre plane, standing over x 4.18, y -1.77, the side leaning 9.3 ± 0.4° to the sensor with its bottom nearer and 0.1° with the picture's right nearer; 158.3 px/in on the near face at the lens's foot; rims within 0.86 px rms; each outline point read where its line of sight meets the plane of the edge it is on: 0.44 in out from the centre plane toward the lens (the near face); the grip's lug (its rear face, sloped face and bottom flat) on its near side at 0.1875; the seat behind the lug on the far edge of its flat (seen from below; the flat's rear edge is a U, from the centre plane to the body's side) at 0 to -0.33 to -0.44 along x; the rear face's lower end, half-round across the body, on its near edge at each height, a round of 0.44; the buffer tower's ring behind its axis, where its rim stands wider than the body, on the rim's near edge at each height, a round of 0.696; the rear underside, round across the body, on its lowest line at 0; the guard's rear ears' rear face on the near ear's outside at 0.3295; the rear ears' bottom on the near ear's outside at 0.3295; the far ear's bottom, seen again past the near ear's front corner, left out; the trigger opening's rear and the rear ears' front corner on the far ear's edge at -0.3295; the trigger opening's top on the body's far edge at -0.44; the trigger opening's front and the front ear on the near ear's outside at 0.3295; the magazine well's bottom and front face on its near wall at 0.549; the top of the well's near wall at 0.549; 2 corner(s) put where two such edges' lines cross (one passes behind the other in the picture); origin at the photo's frame; Douglas-Peucker at 0.01 in with the extremes kept: 79 points (IoU 0.996 with the full outline); The buffer tower's top and front are read at the near face's depth like the body (the model takes the ring from the Army's drawing). With the guard's holes left to the fit the camera leans 7.1 ± 1.2° and what is 2 in below the pin line reads 0.009 in nearer it; checks: −x_min 1.159 ± 0.011; x_max 6.580 ± 0.010 in vs bad-workhorse-lower.front_ahead_of_pin 6.58 ± 0.01 (corroborated): agrees; y_max 1.553 ± 0.010; −y_min 2.368 ± 0.010 in vs bad-workhorse-lower.bottom_below_pin 2.368 ± 0.01 (conflict): agrees; y_min in x [-0.2, 0.08] -1.072 ± 0.010 in vs bad-workhorse-lower.grip_seat_y -1.0695 ± 0.0115 (conflict): agrees; x_min in x [1.0, 1.4] in y [-2.3, -2.05] 1.169 ± 0.010 in vs bad-workhorse-lower.guard_ears_rear_x 1.175 ± 0.015 (confirmed): agrees; x_min in y [-0.5, -0.15] -1.128 ± 0.011 in vs std.ar15.receiver_rear_x -1.125 ± 0.005 (confirmed): agrees (tools/trace.py)","via":"harvest","note":"Outer silhouette with the pin holes filled; the magwell is open at the bottom and the trigger-guard ears are the lowest points. Width is the retailer's maximum."}},"gaps":[]},"bca-556-16-mid-barrel":{"id":"bca-556-16-mid-barrel","name":"BC-15 5.56 NATO, 16\" Parkerized M4 Barrel, 1:7 Twist, Mid-Length Gas System","manufacturer":"Bear Creek Arsenal","sku":"1343-B556MM41617(P)","url":"https://www.bearcreekarsenal.com/556-16-parkerized-m4-barrel-1-7-twist-mid-length.html","category":"barrel","description":"Bear Creek Arsenal's 16 in 5.56 NATO barrel, the one Primary Arms lists as 1343-B556MM41617-P: 4150 chrome moly vanadium, parkerized, 1:7 twist, a mid-length gas system on a .750 in journal, M4 feed ramps, a 1/2-28 muzzle thread. Sold without a gas block or a gas tube.","weight":"bca-556-16-mid-barrel.weight","barrelLength":"bca-556-16-mid-barrel.length","cartridge":{"takes":["5.56 NATO"],"stated":"Caliber 5.56 NATO","source":"https://www.bearcreekarsenal.com/556-16-parkerized-m4-barrel-1-7-twist-mid-length.html (Bear Creek's Specs table, as cached: harvest.quote; Primary Arms' page says \"Chambered in 5.56 NATO\", and the barrel is stamped \"5.56 NATO 1:7\" behind its muzzle in AR15Discounts' photo)"},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"extension":{"origin":[0,0,0],"note":"The barrel extension's flange on the bore axis, its rear face, +x toward the muzzle."},"muzzle":{"origin":["{.shoulder_x}",0,0]},"gas_journal":{"origin":["{.gas_port_x}",0,0]}},"interfaces":{"barrel_extension":{"type":"ar15.barrel_extension","role":"barrel","anchor":"extension","params":{},"flips":false},"muzzle":{"type":"muzzle_thread","role":"barrel","anchor":"muzzle","params":{"thread":"1/2-28","thread_length":"={.thread_length}"},"flips":false,"note":"Bear Creek: \"Thread Pitch 1/2 x 28\"; Primary Arms: \"Thread Pattern 1/2 X 28\". The thread's length isn't published: it is this barrel's photo's (0.60 in), and the Army's barrel has .63."},"gas_journal":{"type":"ar15.gas_journal","role":"barrel","anchor":"gas_journal","params":{"journal_od":"={.journal_od}"},"flips":false,"note":"Bear Creek: \"Gas Block System 0.750\", \"Gas System Mid Length\", \"Does not include gas block or gas tube\". The port is placed by the Army's .295 ahead of the collar the block stops against."},"gas_system":{"type":"ar15.gas_system","role":"barrel","params":{"length":"mid"},"flips":false,"note":"Bear Creek names it \"Mid-Length Gas System\". What the platform checks a gas tube against a barrel by (D83)."}},"materials":{"barrel":{"label":"Barrel","finish":"phosphate","recolorable":false,"color":"steel-parkerized","sheen":"satin","note":"Bear Creek: \"Barrel Finish Parkerized\"; AR15Discounts and Dirty Bird: \"Finish Mag Phosphate / Parkerized\"; Primary Arms: \"Barrel Coating Parkerized\". The black nitride barrel of this shape is another product (Redcon1's B556MM41617(M)). Satin: in Primary Arms' two photos (eff6b190e339, 53fbcf1e58d8) it is a dark grey with an oiled sheen and a blue cast, in Dirty Bird's and AR15Discounts' (b6429b8b7d3c, a1a4be9489ee) a drier neutral charcoal; the colour is matched to the four together (data/colors/steel.yaml). The extension is in this slot: blacker and glossier than the tube in Primary Arms' side view, the same grey in AR15Discounts' view of the breech (f7999eca3fc8). Not drawn: the stamped \"5.56 NATO 1:7\"."},"pin":{"label":"Index pin","finish":"steel","recolorable":false,"color":"stainless-natural","note":"The extension's index pin isn't parkerized: a dull brown steel in Primary Arms' two views of the breech (53fbcf1e58d8, 411aa6f5de8a), a grey steel in AR15Discounts' (f7999eca3fc8). Drawn as bare steel in the app's natural-steel grey, not matched to a photo (a pin a tenth of an inch across)."}},"components":{},"geometry":{"model":"bca-556-16-mid-barrel.glb","components":{},"approximations":["Turned about the bore from one photo, Primary Arms' side view of it: every section is round at the mean of what the photo's upper and lower edges show, thinned to the trace's tolerance. Diameters at the scale its published .750 journal gives; lengths at its published 16 in, taken from the breech face, with the reference CAD set's extension behind that (16.50 in end to end, as the catalog's two other 16 in barrels have it). The two scales agree within 1.0%.","The photo is yawed (the breech end about 4% nearer the lens) and was scaled column by column by the long section under the handguard, taken to be a cylinder: a taper of a few thousandths there would be drawn straight. At the far ends that scale is checked by sizes the Army's drawings give: the chamber section reads 0.980 (.9800), the thread 0.495 (.4924 to .4989), the extension 0.990 (not over .9990).","The flange's two faces, the collar's front face and the muzzle shoulder are squared at the ledger's positions (the photo rounds each corner by its rim's arc); the flange is the reference CAD set's 0.131 in thick, where the photo's two rounded corners span 0.19. The thread is a helix, 28 to the inch, between the Army drawing's minor diameter and the photo's crests: a plain V without the flats of its form, right-hand (assumed: its designation marks no other), running out at the shoulder over its last pitch, with no relief behind it and no chamfer at the muzzle. Rings until 2026-10-06.","The index pin is the Army's (.1255 in across, standing .094 out of the extension, which is its limit), on top against the flange's rear face. The gas port is a plain hole on top of the journal, the Army's .295 ahead of the collar and 0.075 in across by a photo. The bore is one plain hole right through at the Army's .219: the chamber, the muzzle's crown, and the extension's lug cuts and feed ramps aren't drawn.","Not drawn: the dimple under the journal for a gas block's set screw, the relief groove at the collar's front, the marking behind the muzzle ('5.56 NATO 1:7').","Every seller's photo of this number, its maker's included, shows this shape: a plain .75 in cylinder from the gas block's seat to the muzzle shoulder, with a dimple under the seat. A buyer on Primary Arms (August 2024) says the barrels shipped then had 'a squared-off cut-out' and no dimples, and that the pictures don't show the barrel: a cut ahead of the gas block, if today's barrel has one, isn't drawn."],"ledger":["bca-556-16-mid-barrel.overall_length","bca-556-16-mid-barrel.extension_rear_x","bca-556-16-mid-barrel.handguard_section_od","bca-556-16-mid-barrel.journal_od","bca-556-16-mid-barrel.flange_front_x","bca-556-16-mid-barrel.journal_shoulder_x","bca-556-16-mid-barrel.gas_port_x","bca-556-16-mid-barrel.gas_port_d","bca-556-16-mid-barrel.shoulder_x","bca-556-16-mid-barrel.thread_length","bca-556-16-mid-barrel.thread_od","bca-556-16-mid-barrel.thread_minor_d","bca-556-16-mid-barrel.thread_pitch","bca-556-16-mid-barrel.muzzle_od","bca-556-16-mid-barrel.index_pin_d","bca-556-16-mid-barrel.index_pin_x","bca-556-16-mid-barrel.index_pin_protrusion","bca-556-16-mid-barrel.bore_d"]},"profiles":{"side":{"plane":"xy","origin":"the extension's rear face, on the axis (column 2099.6 of the photo: the silhouette's tip at 2103.5 is that face's near rim)","offset":{"x":"extension_rear_x"},"points":[[0,0.36],[0,-0.24],[0.04,-0.307],[0.04,-0.323],[0.032,-0.331],[0.032,-0.347],[0.017,-0.38],[0.017,-0.412],[0.052,-0.474],[0.099,-0.499],[0.47,-0.503],[0.478,-0.494],[0.857,-0.499],[0.865,-0.49],[0.976,-0.492],[0.996,-0.504],[1.012,-0.537],[1.047,-0.574],[1.111,-0.591],[1.119,-0.583],[1.158,-0.583],[1.194,-0.547],[1.202,-0.515],[1.222,-0.494],[1.357,-0.496],[1.365,-0.488],[1.786,-0.492],[1.897,-0.436],[1.913,-0.436],[1.961,-0.412],[1.985,-0.413],[2.017,-0.396],[2.073,-0.389],[2.08,-0.381],[2.104,-0.381],[2.112,-0.373],[2.144,-0.373],[2.152,-0.365],[2.176,-0.365],[2.184,-0.357],[2.224,-0.358],[2.232,-0.35],[2.296,-0.35],[2.304,-0.342],[2.543,-0.345],[2.551,-0.353],[2.615,-0.354],[2.623,-0.345],[3.272,-0.352],[3.28,-0.344],[4.036,-0.352],[4.044,-0.344],[4.933,-0.353],[4.941,-0.345],[5.647,-0.352],[5.656,-0.344],[5.664,-0.352],[5.672,-0.344],[6.446,-0.352],[6.455,-0.343],[7.298,-0.352],[7.307,-0.344],[8.105,-0.352],[8.113,-0.344],[8.336,-0.346],[8.344,-0.338],[8.683,-0.341],[8.692,-0.35],[8.774,-0.35],[8.783,-0.359],[8.841,-0.359],[8.849,-0.368],[8.882,-0.368],[8.89,-0.377],[8.915,-0.377],[8.923,-0.385],[8.948,-0.386],[8.981,-0.403],[9.006,-0.403],[9.039,-0.42],[9.056,-0.42],[9.064,-0.428],[9.089,-0.429],[9.098,-0.437],[9.114,-0.437],[9.131,-0.454],[9.147,-0.454],[9.222,-0.497],[9.23,-0.489],[9.679,-0.493],[9.687,-0.485],[9.812,-0.486],[9.841,-0.449],[9.841,-0.416],[9.85,-0.407],[9.85,-0.382],[9.862,-0.361],[9.879,-0.362],[9.887,-0.37],[9.971,-0.371],[9.979,-0.379],[10.071,-0.38],[10.079,-0.372],[10.112,-0.372],[10.121,-0.381],[10.171,-0.381],[10.179,-0.373],[10.748,-0.379],[10.756,-0.37],[11.62,-0.379],[11.629,-0.371],[12.43,-0.379],[12.438,-0.371],[13.583,-0.382],[13.592,-0.374],[14.521,-0.383],[14.538,-0.375],[14.547,-0.383],[14.581,-0.384],[14.59,-0.375],[15.267,-0.382],[15.275,-0.374],[15.292,-0.374],[15.301,-0.383],[15.309,-0.374],[15.318,-0.383],[15.327,-0.374],[15.335,-0.383],[15.344,-0.375],[15.352,-0.383],[15.361,-0.375],[15.843,-0.379],[15.851,-0.371],[15.869,-0.371],[15.881,-0.359],[15.881,-0.35],[15.899,-0.333],[15.916,-0.299],[15.916,-0.282],[15.925,-0.265],[15.937,-0.253],[15.963,-0.262],[15.972,-0.253],[16.058,-0.254],[16.075,-0.263],[16.093,-0.254],[16.11,-0.263],[16.127,-0.255],[16.144,-0.263],[16.153,-0.255],[16.17,-0.255],[16.179,-0.264],[16.188,-0.255],[16.447,-0.258],[16.481,-0.241],[16.501,-0.222],[16.501,0.2],[16.481,0.219],[16.447,0.237],[16.386,0.237],[16.378,0.246],[16.36,0.237],[16.343,0.238],[16.334,0.246],[16.326,0.238],[16.308,0.238],[16.3,0.246],[16.291,0.238],[16.274,0.238],[16.265,0.247],[16.257,0.238],[16.067,0.24],[16.058,0.231],[15.989,0.232],[15.981,0.241],[15.972,0.232],[15.963,0.241],[15.929,0.241],[15.907,0.279],[15.907,0.297],[15.89,0.314],[15.89,0.322],[15.851,0.361],[15.834,0.369],[15.705,0.37],[15.696,0.362],[15.688,0.371],[15.671,0.362],[15.653,0.362],[15.645,0.371],[15.627,0.363],[15.61,0.371],[15.593,0.371],[15.576,0.363],[15.567,0.372],[15.559,0.363],[14.205,0.374],[14.196,0.366],[13.048,0.375],[13.039,0.366],[11.62,0.378],[11.612,0.369],[11.578,0.37],[11.562,0.378],[11.553,0.37],[10.488,0.378],[10.48,0.37],[10.421,0.371],[10.405,0.379],[10.396,0.371],[9.896,0.375],[9.887,0.366],[9.871,0.367],[9.854,0.358],[9.833,0.446],[9.816,0.48],[9.796,0.493],[9.504,0.495],[9.496,0.487],[9.479,0.495],[9.446,0.495],[9.438,0.487],[9.205,0.489],[9.098,0.431],[9.081,0.431],[9.073,0.423],[9.056,0.423],[9.048,0.415],[9.031,0.415],[8.998,0.399],[8.973,0.399],[8.965,0.391],[8.907,0.383],[8.899,0.374],[8.865,0.375],[8.857,0.366],[8.824,0.367],[8.816,0.358],[8.783,0.359],[8.774,0.35],[8.725,0.351],[8.716,0.343],[8.567,0.344],[8.559,0.336],[8.435,0.337],[8.427,0.345],[8.419,0.337],[8.394,0.337],[8.386,0.345],[8.237,0.347],[8.229,0.355],[8.22,0.347],[7.504,0.353],[7.496,0.344],[6.455,0.353],[6.446,0.345],[5.542,0.352],[5.534,0.344],[5.038,0.348],[5.03,0.34],[5.022,0.348],[5.014,0.34],[4.941,0.34],[4.933,0.349],[4.504,0.352],[4.496,0.344],[3.843,0.35],[3.835,0.341],[3.601,0.343],[3.593,0.352],[3.409,0.353],[3.401,0.345],[2.535,0.352],[2.527,0.344],[2.264,0.346],[2.256,0.355],[2.192,0.355],[2.184,0.363],[2.128,0.364],[2.12,0.372],[2.073,0.372],[2.065,0.381],[2.041,0.381],[2.033,0.389],[2.017,0.389],[1.985,0.406],[1.961,0.406],[1.897,0.439],[1.857,0.448],[1.778,0.489],[1.452,0.492],[1.444,0.484],[1.428,0.484],[1.42,0.492],[1.412,0.484],[1.206,0.486],[1.186,0.523],[1.186,0.539],[1.15,0.576],[1.127,0.584],[1.119,0.576],[1.032,0.577],[0.996,0.54],[0.992,0.528],[0.976,0.528],[0.937,0.496],[0.668,0.498],[0.66,0.49],[0.123,0.494],[0.115,0.486],[0.06,0.487],[0.04,0.466],[0.032,0.442],[0.009,0.41]],"scaleRefs":["bca-556-16-mid-barrel.handguard_section_od","bca-556-16-mid-barrel.overall_length"],"inputs":{"bca-556-16-mid-barrel.handguard_section_od":0.6976,"bca-556-16-mid-barrel.overall_length":16.501},"tolerance":0.004,"photo":"references/bca-556-16-mid-barrel eff6b190e339 (Primary Arms 1343-B556MM41617-P_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","method":"luminance < 235, largest piece, holes filled; scale from bca-556-16-mid-barrel.handguard_section_od = 0.6976 in, the tube's own width column by column: 84.0 px over columns 1080–1200, 84.1 px over columns 1200–1400, 84.6 px over columns 1400–1600, 85.2 px over columns 1660–1790; a line through them (rms 0.19 px) changes +1.7% from column 1080 to 1790, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 120.1 px/in there. The axis is the tube's centre line (tilt +0.52°, rms 0.08 px). Lengths then scaled by 0.9904 so that the end faces are bca-556-16-mid-barrel.overall_length = 16.501 in apart: at the tube's scale they read 16.662 (+1.0%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.046 in over radius 0.190 (rms 0.004), the rear end's rim sags 0.036 in over radius 0.300 (rms 0.003); origin at column 2099.6 of the photo, on the tube's axis; clipped to x min 0 = 0, x max {.overall_length} = 16.501; Douglas-Peucker at 0.004 in with the extremes kept: 314 points (IoU 0.998 with the full outline); Diameters at the journal's scale, lengths at the published length's between the end faces, and the outline cut at those faces (the tips beyond them are the rims' near sides).; checks: height (tooth tops, max over 0.05 in windows) along x [9.75, 11.1] 0.750 ± 0.026 in vs bca-556-16-mid-barrel.journal_od 0.75 ± 0.0005 (confirmed): agrees; the min end's face: the silhouette's tip at -0.035 less its rim's arc, 0.036 in of sag at radius 0.3 (the end is seen from 6.8° off square; arc fitted over 113 rows, rms 0.003) 0.001 ± 0.013; the max end's face: the silhouette's tip at 16.548 less its rim's arc, 0.046 in of sag at radius 0.19 (the end is seen from 13.5° off square; arc fitted over 121 rows, rms 0.004) 16.502 ± 0.155 (tools/trace.py)","via":"harvest","note":"Dark grey on white: the outline is the silhouette at 235 of 255. The rear end at x 0, the muzzle face at the published length; the thread is its silhouette."}},"gaps":[{"what":"Which barrel ships today: with or without a cut-out ahead of the gas block's seat, with or without the dimple the photos show","need":"A dated photo of a delivered 1343-B556MM41617(P), or Bear Creek's own drawing of it"},{"what":"Its weight: four published figures from 28 to 30.4 oz, none with a method; 29 oz is adopted, which two listings give and the model's volume supports","need":"A weighed barrel, or Bear Creek saying whether its 1.75 lb is the barrel bare"},{"what":"A second view of its profile: it is one photo, yawed","need":"A straight side photo with a scale in the barrel's plane, or the maker's profile drawing"},{"what":"What its 16 in is measured between (taken from the breech face; the Army measures from the bolt's face, 0.126 further back)","need":"The maker's drawing, or a rod's reading on a barrel in hand"},{"what":"The gas port's diameter and the dimple's place","need":"The maker's figure: neither is published"},{"what":"Where its flange's rear face is within 0.03 in, and with it everything ahead of the receiver (the muzzle shoulder, the gas port)","need":"A straight side photo of the breech end. This one sees it from about 6° off square: the face is taken where the outline first stands over 0.53 in from the axis, 0.996 in ahead of the extension's rear face, as the standard extension has it (0.990); the flange's flat top begins 0.03 to 0.05 ahead of that, and if the face is there the shoulder is 14.88 in ahead of the receiver, not 14.91"}]},"bca-stripped-lower":{"id":"bca-stripped-lower","name":"BC-15 Multi Caliber, Lower Receiver, Black Anodized","manufacturer":"Bear Creek Arsenal","sku":"LR-15","url":"https://www.bearcreekarsenal.com/guns-parts/ar-15/ar-15-lowers/stripped-lower-receivers/bca-ar-15-lower-receiver-multi-caliber-black-anodized.html","category":"lower","description":"Bear Creek's forged stripped lower, roll-marked BCA15 and MULTI CALIBER: \"fully machined, anodized black and forged to mil-spec from 7075 aluminum\" (Bear Creek). Primary Arms lists it as \"Bear Creek Arsenal AR-15 Lower Receiver - Stripped Lower\" (BCA-LR-15) and says it \"ships stripped, ready for the lower parts kit, buffer assembly, and stock of the builder's choice\". No trigger guard: a separate one pins into its ears.","weight":"bca-stripped-lower.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"pins":{"origin":[0,0,0],"note":"The rifle frame origin."},"buffer_tube_mount":{"origin":[0,"{.buffer_axis_above_pin}",0],"x":[-1,0,0]},"magwell":{"origin":["{.magazine_seat_x}","{std.ar15.mag_catch_slot_bottom_y} + {std.ar15.mag_catch_slot_h}",0],"note":"Where a seated magazine hangs: x where its spine's rear face sits in the well (magazine_seat_x), y at the catch's upper face, which is the top of the slot the catch comes through (the Army's drawing). A magazine's own anchor is the upper edge of its catch notch, so each hangs by its own. Until 2026-10-05 this was the feed lips' top of a seated Black Dog (magazine_seat_y, still in the ledger as that), and a PMAG, whose notch is 0.37 in nearer its top, hung that much too high: its lips above the bore. The Army drawing's well and catch slot, as the catalog's other mil-spec lowers have it: no photo of a magazine seated in this lower is on file."},"grip_lug":{"origin":[0,"{.grip_seat_y}",0],"note":"The grip mount's datum: the face either side of the lug that a grip's flat top bears on, at the takedown pin's x: the Army drawing's, 1.318 below the deck (the right photo's own reading is 0.025 above it)."},"trigger_guard":{"origin":["{.trigger_guard_front_x}","{.trigger_guard_front_y}",0],"x":["{.trigger_guard_front_x} - {.trigger_guard_rear_x}","{.trigger_guard_front_y} - {.trigger_guard_rear_y}",0],"note":"At the front ear hole, with the guard's x axis through the rear ear hole: a guard pins into both. The Army drawing's holes."},"fcg":{"origin":["{.trigger_pin_x}","{.trigger_pin_y}",0],"note":"Trigger pin axis."},"lpk":{"origin":[0,0,"-{std.ar15.lower_body_width} / 2"],"note":"The body's left face (the TDP's width), level with the takedown pin: the controls' heads seat on it."},"selector":{"origin":["{std.ar15.selector_x}","{std.ar15.selector_y}",0],"note":"The selector's hole (the Army's drawing 8448608), on its axis at the receiver's mid-plane: a selector chosen on its own turns here (D86), its levers' inner faces on the body's two sides."}},"interfaces":{"receiver_pins":{"type":"ar15.upper_lower","role":"lower","anchor":"pins","params":{"pin_spacing":"={std.ar15.pin_spacing}"},"flips":false},"buffer_tube_mount":{"type":"ar15.buffer_tube_mount","role":"receiver","anchor":"buffer_tube_mount","params":{},"flips":false},"magwell":{"type":"ar15.magwell","role":"receiver","anchor":"magwell","params":{"family":"5.56"},"flips":false,"note":"A standard AR-15 magazine well: 'Platform AR-15', 'Compatible with standard AR-15 components' (Primary Arms); marked MULTI CALIBER."},"grip_lug":{"type":"ar15.grip_lug","role":"receiver","anchor":"grip_lug","params":{},"flips":false},"trigger_guard":{"type":"ar15.trigger_guard","role":"receiver","anchor":"trigger_guard","params":{},"flips":false},"fcg":{"type":"ar15.fcg","role":"receiver","anchor":"fcg","params":{"pin_diameter":"small-pin"},"flips":false,"note":"'Trigger Pin Diameter MIL-SPEC .154' (Primary Arms)."},"lpk":{"type":"ar15.lpk","role":"receiver","anchor":"lpk","params":{},"flips":false},"selector":{"type":"ar15.selector","role":"receiver","anchor":"selector","params":{},"flips":false}},"materials":{"receiver":{"label":"Receiver","finish":"anodized","recolorable":true,"color":"placeholder-black","sheen":"matte","options":{"black":{"label":"Black Anodized","finish":"anodized","color":"placeholder-black","sheen":"matte","sku":"LR-15","source":"https://www.bearcreekarsenal.com/guns-parts/ar-15/ar-15-lowers/stripped-lower-receivers/bca-ar-15-lower-receiver-multi-caliber-black-anodized.html"},"fde":{"label":"Flat Dark Earth","finish":"cerakote","color":"bear-creek-fde","sku":"LR-15FDE","source":"https://www.bearcreekarsenal.com/bca-ar-15-lower-receiver-multi-caliber-flat-dark-earth-cerakote.html"}},"default":"black","note":"'Anodized Black' (Bear Creek), 'Finish Hardcoat Anodized', 'Color Black' (Primary Arms). The other (2026-10-06) is Bear Creek's own page for LR-15FDE, which names the coat two ways: its title \"Flat Dark Earth Cerakote\", its item \"Lower Receiver Multi Caliber, Flat Dark Earth Powder Coat\" and its description \"*Powder Coat Frosted Tan*\". Drawn as a sprayed matte coat (the cerakote type: there is no powder coat type), matched on that page's one photo. A search result names an un-anodized one (LR-15W): the address it gave answered 404 on 2026-10-06, so nothing of it is read and it isn't offered. The black is unmatched (sealed black anodize)."}},"components":{"receiver":{"label":"Receiver","material":"receiver"}},"geometry":{"model":"bca-stripped-lower.glb","components":{},"approximations":["Its two photos are taken from about two feet and 3.4 in above the pin line, not square to it: each was laid square onto its near face by a camera fitted to the Army drawing's holes on the part before anything was read. What stands behind that face reads high by its depth x 0.12 (at the deck) to 0.21 (at the trigger guard's ears): the outline is the right face's. Put at the depths the standard gives them, what it shows below the pin line (the grip's lug, the trigger guard's holes) still reads 0.02 to 0.03 in high; the ears' own outline and the well's lower edge are drawn as the outline has them.","The grip's mount is the standard's, not read from this lower's photos: the face a grip bears on 1.318 below the deck and the lug at the drawing's .375 across, its rear face under the takedown pin, its sloped face 1.228 from the pin at 60 degrees, its flat .93 below the seat (the Army's drawing 8448608); the walls with the trigger guard's ears 0.659 across (the reference CAD model) and the ears .438 +.008 apart (the drawing); the rear underside the reference model's, an arc on the centre plane and a half-round across the body, so the seat's rear edge is a U. The right photo's outline, traced as a slab, has the lug 0.05 high: at the lug's own depth its sloped face is 1.225 from the pin at 60.5 degrees, the drawing's. Behind the lug the outline lies 0.10 to 0.15 above the reference model's centre line, 0.06 to 0.10 of which is how a half-round shows from that camera; the other 0.03 to 0.06 isn't explained. Where the ears and the trigger's opening begin is the outline's (the ears 0.025 ahead of the drawing's); the walls step in square at the seat's level, where the reference model flares them over 0.15 in.","The traced outline at the TDP's body width (0.880), its magazine well's walls at 1.098 from each side's measured rear edge forward (on the left from the curved edge the left photo shows), and the buffer tower's ring at 1.392 about the buffer axis, its top and its rear face the drawing's (the right photo has the ring's top 0.03 above the drawing's).","The tower's bore through the ring and on along the trough between the walls' sweep, cut at the mil-spec receiver extension's OD (1.148): the thread it really has is larger by its depth, which isn't on file. The walls' sweep is drawn at the ring's width back to where the outline's sweep ends, stepping to the body's there. The walls rise to the ring's front face along the Army drawing's arc (.750 R, 8448608 sheet 1: 2026-10-12) and no higher: the outline has them up to 0.16 in above it. Its deck, from just behind the takedown pin to where its top turns down at the pivot lug, is the Army drawing's plane (.250 -.003 above the pins: std.ar15.deck_y), not the outline's own top edge, which reads a hundredth off it and not level (2026-10-12): the deck is the seat every upper sits on.","The inside a forged mil-spec lower has, from the Army's drawing 8448608 (D46): the fire-control pocket, the rear lug's slot, the safety detent's boss, the trigger slot and the magazine well with its spine slot, open from the deck to the mouth. A seller says 'Low Shelf Trigger Pocket'; nothing of its own inside is measured.","The pivot lug as its two ears: the slot the upper's front lug goes in, the drawing's .500 across, cut through the lug ahead of the well's front face. How far down the slot runs into the well's front wall behind that face isn't on file: the wall is left whole between the ears.","The holes its photos show open, at the drawing's sizes and places: the takedown and pivot pins', the selector's, the hammer's and trigger's (each rim found on both photos within 0.014 in of the drawing's), the trigger guard's roll pin hole through both ears and its front hole in the right ear from its spotface (on the ears' own face these read 0.02 to 0.03 high on the photos, inside their ±: the drawing's places are used); the takedown hole's spotface on the right, where the right photo shows its ring.","On the left, as the left photo has them where the drawing and the reference CAD model put them: the magazine catch's slot opening into the well, the catch hole through to the button's pocket, the band down the well's wall and the round boss the slot runs through (the model's), the bolt catch's two bosses (their outlines from the photo, out to the TDP's face) and its slot and plunger hole.","On the right, the magazine catch's fence: its flat face where the right photo has it, out to the well walls' face, run on forward into the wall and up under the roll (2026-10-05: as an island it left the body showing as a groove where the photo has a rib), its rear and lower sides rounded; the button's pocket and the counterbore from the reference model.","The roll along the top of the well's right wall (2026-10-05), the forging's own and the widest thing on the receiver: a half-round bar from above the fence's rear (X 2.91) to a flat end beside the pivot lug (6.237, where the Army's pivot pin has the flat on its head), its top the deck's edge, its lower edge 0.204 in below the pin line: all three read on this lower's right photo, and the Workhorse's to the hundredth. Its crest is the Workhorse's 0.80 in from the centre (read there through a camera fitted to an oblique photo, and checked by that lower's published width): this lower's own photo, from 7 degrees above, says 0.85 ± 0.07 if its small hole is at the Workhorse's height. Drawn as half an ellipse through the three places read, its rear end rounded. It meets the wall under it at a crease where the part blends into the wall. The kit's pivot pin head is drawn with its flat (the Army's drawing 8448621) toward the roll's front end, a hair clear of it.","Not drawn: the roll marks (the bear, BEAR CREEK ARSENAL, MODEL: BCA15, MULTI CALIBER, the serial number, SANFORD, NC, USA, FIRE and SAFE), the two oblong pockets either side of the selector on the left, the rib that runs down from the roll beside the magazine catch's fence to a point, with the ridge round the fence (how far they stand off the walls' face can't be read from a side view, on this lower or the Workhorse), the grip screw's hole in the lug, the pivot hole's countersink, the bore's thread and the buffer retainer's hole, and the small blind hole in the roll 1.0 in behind the pivot pin.","Edges broken at 0.02 in (the drawing's \"break corners .02 R\"); the well's flared lip and the takedown and pivot lugs' ears at the widths above."],"ledger":["std.ar15.lower_body_width","std.ar15.magwell_outside_width","std.ar15.buffer_tower_od","std.ar15.buffer_tower_front_x","std.receiver_extension.milspec_od","std.ar15.fcg_pocket_front_x","std.ar15.fcg_pocket_depth","std.ar15.magwell_front_inner_x","std.ar15.front_lug_slot_width","bca-stripped-lower.well_roll_crest_out","bca-stripped-lower.well_roll_bottom_y","bca-stripped-lower.well_roll_rear_x","bca-stripped-lower.well_roll_front_x","std.ar15.grip_seat_below_deck","std.ar15.grip_lug_width","std.ar15.grip_lug_face_from_pin","std.ar15.grip_lug_depth","std.ar15.trigger_guard_ears_width","std.ar15.trigger_guard_ear_gap","std.ar15.rear_underside_arc_r","std.ar15.rear_underside_round_r","std.ar15.takedown_hole_d","std.ar15.selector_hole_d","std.ar15.fcg_pin_hole_d","std.ar15.mag_catch_fence_out","std.ar15.bolt_catch_boss_out","std.ar15.pin_spacing","bca-stripped-lower.buffer_axis_above_pin","bca-stripped-lower.rear_behind_pin","bca-stripped-lower.tower_front_x","bca-stripped-lower.magwell_front_x","bca-stripped-lower.magwell_wall_rear_x","bca-stripped-lower.magwell_wall_rear_x_left","bca-stripped-lower.magwell_wall_upper_rear_x_left","bca-stripped-lower.fence_rear_x","bca-stripped-lower.fence_front_x","bca-stripped-lower.fence_top_y","bca-stripped-lower.fence_bottom_y","bca-stripped-lower.bolt_catch_boss_rear_x","bca-stripped-lower.bolt_catch_boss_front_x","bca-stripped-lower.trigger_guard_front_x","bca-stripped-lower.trigger_guard_rear_x","bca-stripped-lower.trigger_pin_x","bca-stripped-lower.trigger_pin_y","bca-stripped-lower.magazine_seat_x","bca-stripped-lower.magazine_seat_y","bca-stripped-lower.grip_seat_y","bca-stripped-lower.width"]},"profiles":{"side":{"plane":"xy","origin":"the takedown pin centre (the rifle frame origin), +x toward the muzzle","offset":{},"points":[[-1.17,0.828],[-1.105,-0.223],[-1.065,-0.393],[-0.728,-0.455],[-0.458,-0.62],[-0.335,-0.772],[-0.22,-1.018],[-0.03,-1.047],[-0.025,-1.317],[0.012,-1.355],[1.027,-1.93],[1.172,-1.93],[1.2,-1.958],[1.212,-2.28],[1.652,-2.285],[1.74,-2.208],[1.485,-1.962],[1.39,-1.703],[1.395,-1.533],[1.45,-1.342],[1.603,-1.15],[1.887,-1.05],[2.878,-1.05],[3.133,-1.18],[3.213,-1.19],[3.34,-1.368],[3.39,-1.698],[3.3,-1.933],[3.155,-2.097],[3.15,-2.217],[3.232,-2.305],[3.393,-2.295],[3.497,-2.33],[3.527,-2.295],[4.503,-2.15],[6.188,-1.83],[6.215,-1.743],[6.09,-1.533],[6.1,-0.572],[6.165,-0.408],[6.282,-0.275],[6.545,-0.143],[6.59,-0.062],[6.59,0.052],[6.555,0.133],[6.467,0.19],[6.188,0.205],[6.107,0.255],[5.987,0.27],[-0.018,0.265],[-0.283,0.4],[-0.475,0.633],[-0.595,0.953],[-0.58,1.232],[-0.63,1.538],[-0.658,1.565],[-0.973,1.57],[-1.083,1.54],[-1.125,1.488],[-1.155,1.353]],"scaleRefs":["std.ar15.pin_spacing"],"inputs":{"std.ar15.pin_spacing":6.375},"tolerance":0.02,"photo":"references/bca-stripped-lower 2376eb37b2cc (right side: Primary Arms' photo 269cebb44010 laid square onto the right face by the drawing's holes, the far wall's overhang taken off)","method":"alpha > 0.5, largest piece, holes filled; frame from the reviewed holes takedown, pivot (200.0 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.02 in with the extremes kept: 60 points (IoU 0.991 with the full outline); the picture's pins are where the rectification put the drawing's (its camera has each hole's rim within 0.007 in of the drawing); the bolt catch's slot, seen through the far wall as a notch at the deck, is closed in the picture's outline; checks: −x_min 1.170 ± 0.008; x_max 6.590 ± 0.011; y_max 1.570 ± 0.008; −y_min 2.330 ± 0.008; top (tooth tops: the edge's max over 0.05 in windows) along x [0.6, 5.8] 0.260 ± 0.015 in vs std.ar15.deck_y 0.2485 ± 0.0015 (confirmed): agrees; −x_min in y [-0.9, 0.0] 1.120 ± 0.008 (tools/trace.py)","via":"harvest","note":"The right face's outline, its holes filled; no trigger guard (the ears are the lowest points behind the well). The tower ring is round, not a prism: its top and rear read as its silhouette does from this camera and are the drawing's in the model."}},"gaps":[{"what":"its weight: the maker's page says 1 lb in a store's field, a seller 11.2 oz beside what reads as a box's size; neither is a weighing of the bare receiver","need":"a page or a reviewer that weighs the stripped receiver"},{"what":"a view square to the receiver: both photos are oblique (26 to 28 in away, 7 degrees above), so every reading goes through a fitted camera, and the left one's frame leans half a degree (its pivot hole's rim is unclear)","need":"a straight side photo with both pin holes open, or a photo from further away"},{"what":"everything read below the pin line on its photos is 0.02 to 0.03 in above the drawing's once its depth is allowed for (the grip's seat and lug, the trigger guard's holes), and the rear underside 0.03 to 0.06 above the reference model's: the drawing's and the model's are used, and the ears' and the well's lower edges may be drawn that much high","need":"a straight side photo, or where the camera's axis met the picture (it is taken at each picture's centre)"},{"what":"the depth of the two oblong pockets by the selector and of the panel on the well's right wall","need":"an oblique close-up with a known edge beside them, or a view along the receiver"}]},"bcm-115-carbine-barrel":{"id":"bcm-115-carbine-barrel","name":"Standard 11.5\" Carbine Barrel, Stripped","manufacturer":"BCM","sku":"BCM-BRL-s-11-STD","url":"https://bravocompanyusa.com/bcm-standard-11-5-carbine-barrel-stripped-nfa/","category":"barrel","description":"Bravo Company's 11.5 in government-profile barrel, stripped: MIL-B-11595E chrome moly vanadium steel, a chrome lined 5.56 NATO chamber and bore, 1/7 twist, manganese phosphate, a carbine-length gas port drilled and dimpled on a .750 in journal, an M4 feed ramp extension, a 1/2-28 muzzle thread.","weight":"bcm-115-carbine-barrel.weight","barrelLength":"bcm-115-carbine-barrel.length","cartridge":{"takes":["5.56 NATO"],"stated":"5.56 NATO Chambers","source":"https://bravocompanyusa.com/bcm-standard-11-5-carbine-barrel-stripped-nfa/ (a heading of BCM's description, as cached: harvest.quote; the seller Primary Arms has \"Chambered in 5.56 NATO, 1:7 twist\" for the same number)"},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"extension":{"origin":[0,0,0],"note":"The barrel extension's flange, its rear face, on the bore axis, +x toward the muzzle."},"muzzle":{"origin":["{.shoulder_x}",0,0]},"gas_journal":{"origin":["{.gas_port_x}",0,0]}},"interfaces":{"barrel_extension":{"type":"ar15.barrel_extension","role":"barrel","anchor":"extension","params":{},"flips":false,"note":"BCM: \"M4 Feed Ramp Barrel Extension\"; Primary Arms, for this number: \"M4 feed ramp barrel extension\"."},"muzzle":{"type":"muzzle_thread","role":"barrel","anchor":"muzzle","params":{"thread":"1/2-28","thread_length":"={.thread_length}"},"flips":false,"note":"The thread is the seller's statement, not the maker's: Primary Arms, for this number, \"Threaded 1/2x28\" and \"Thread Pattern 1/2 X 28\"; BCM's barrel page states none. Its length is read off the photo (0.624 ± 0.025 in: the Army barrel's .63), where its pitch reads 28 to the inch within 0.4%."},"gas_journal":{"type":"ar15.gas_journal","role":"barrel","anchor":"gas_journal","params":{"journal_od":"={.journal_od}"},"flips":false,"note":"BCM: \"(.750) at Gas Block location\"; \"gas ports installed and dimpled for a strong gas block installation\"; Primary Arms: \"Dimpled gas block shelf\". The journal runs from 6.88 to 8.80 in ahead of the receiver's face, the port 0.26 in ahead of its rear shoulder."},"gas_system":{"type":"ar15.gas_system","role":"barrel","params":{"length":"carbine"},"flips":false,"note":"BCM names it \"Standard 11.5\" Carbine Barrel, Stripped\" and says \"These are stripped 11.5\" carbine gas Standard 11595E barrels\" (https://bravocompanyusa.com/bcm-standard-11-5-carbine-barrel-stripped-nfa/); Primary Arms, for the same number: \"Carbine-length gas system\" and \"Gas System Length Carbine\". What the platform checks a gas tube against a barrel by (D83)."}},"materials":{"barrel":{"label":"Barrel","finish":"phosphate","recolorable":false,"color":"steel-phosphate-charcoal","note":"BCM: \"Manganese Phosphate Barrel Finish\" and \"Barrels are parkerized with the manganese phosphate finish per Mil-Spec\" (https://bravocompanyusa.com/bcm-standard-11-5-carbine-barrel-stripped-nfa/); Primary Arms' table: \"Barrel Coating Manganese Phosphate\". The one finish this number is sold in. One slot: in Primary Arms' five photos the extension, its index pin, the collar, the journal and the sections ahead of it are one matte charcoal (the whole barrel reads #4b4b4a in its side view, 4e5aad5ce36e, the journal #484848, the extension #373737; #3d3d3d and #42423f in its three-quarter view, 9d72497edd10; its close views darker, #252525 to #353535), round what the 16 in barrel's photos read and its preset was fitted to (#3f3f3e). Not drawn: the chrome of the bore and the chamber (\"Chrome Bore and Chamber\": inside), the two feed ramps and the muzzle's face, cut bright after the finish, the stamped \"HP MP 1/7 5.56 NATO\"."}},"components":{},"geometry":{"model":"bcm-115-carbine-barrel.glb","components":{},"approximations":["Turned from stations read off Primary Arms' side photo of this barrel: each section's diameter and each step's place, through the photo's calibration (the lens about 65 in off; the barrel leaning 0.9° to it, its scale 0.3% smaller at the muzzle than at the breech; the cut-out's edge a pixel inside the barrel's). Three knowns fix that calibration: the extension's body at the Army drawing's .999, the journal at the published .750, the length at the published one (11.5 in from its breech end, with the extension's half inch behind that: 12.00). The thread's own pitch in the photo, which is none of the three, has the same scale within 0.4%; and the same photo's traced outline, mapped through the calibration, lies within 0.008 in of the turned profile wherever it is clear of a step.","The collar's front corner and the muzzle shoulder's are cut off at 45° by 0.037 and 0.035 in, as the photo's edges fall before each face (as far toward the axis as along it, within a pixel); every other step is square at the face read off the photo, where the journal's front corner is broken by less than a hundredth. A face is where its rim's arc begins (2 to 5 px deep from this far). The taper ahead of the chamber is a straight cone; the section under the handguard a cone as far as a knee (.679 to .654 in) and level from there, where the photo's edges turn over a third of an inch; the ramp up to the collar an arc through its two ends and a station between.","The relief groove at the collar's front face is cut as the photo's silhouette has it, 0.046 in wide and 0.012 deep: the lens's blur fills a groove that narrow a little, and it may be deeper.","The indexing pin at the reference CAD set's .125 (the photo's own reads .126), where and as high as the photo has it; the gas port at the size read on a close photo of the journal (.078 in), on top of the journal where the photo's two edges are nicked; the bore one plain hole right through, at the Army drawing's .219; the extension's rear opening turned at the reference CAD set's sizes (its chamfered mouth, the ring its locking lugs make, the recess ahead of them).","The muzzle thread is a helix, 28 to the inch, between the minor and major diameters of the Army barrel's 1/2-28 thread (the seller states 1/2 X 28): a plain V without the flats of its form, right-hand (assumed: its designation marks no other), running out at the shoulder over its last pitch where the photo has a plain relief 0.06 in long, with no chamfer at the muzzle.","Not drawn: the dimple under the journal opposite the port (0.144 in across by the photo; its depth isn't shown) and the ring round the port's mouth, the break at the muzzle's crown (about 0.03 in by the photo), the chamber, the slots between the extension's locking lugs and its two feed ramps (the lugs are one ring), the marking on the section under the handguard (HP MP 1/7 5.56 NATO)."],"ledger":["bcm-115-carbine-barrel.length","bcm-115-carbine-barrel.overall_length","bcm-115-carbine-barrel.extension_rear_x","bcm-115-carbine-barrel.flange_front_x","bcm-115-carbine-barrel.shoulder_x","bcm-115-carbine-barrel.thread_length","bcm-115-carbine-barrel.gas_port_x","bcm-115-carbine-barrel.journal_od","bcm-115-carbine-barrel.muzzle_od"]},"profiles":{"side":{"plane":"xy","origin":"the silhouette's rear tip, on the axis; the outline begins at the extension's rear face","offset":{"x":"extension_rear_x"},"points":[[0.046,0.499],[0.046,-0.484],[0.061,-0.493],[0.122,-0.493],[0.128,-0.499],[0.794,-0.496],[0.8,-0.502],[1.026,-0.502],[1.035,-0.511],[1.048,-0.572],[1.075,-0.593],[1.173,-0.587],[1.182,-0.577],[1.176,-0.553],[1.197,-0.55],[1.207,-0.541],[1.219,-0.504],[1.228,-0.495],[1.258,-0.495],[1.265,-0.488],[1.271,-0.495],[1.283,-0.488],[1.307,-0.488],[1.662,-0.487],[1.68,-0.493],[1.698,-0.493],[1.705,-0.487],[1.753,-0.487],[1.76,-0.493],[1.845,-0.492],[1.851,-0.486],[1.949,-0.474],[1.955,-0.468],[2.096,-0.449],[2.132,-0.436],[2.193,-0.43],[2.199,-0.424],[2.267,-0.418],[2.273,-0.411],[2.309,-0.411],[2.346,-0.399],[2.389,-0.399],[2.425,-0.386],[2.456,-0.386],[2.493,-0.374],[2.56,-0.368],[2.566,-0.362],[2.633,-0.355],[2.639,-0.349],[2.67,-0.349],[2.676,-0.343],[2.706,-0.343],[2.712,-0.337],[3.843,-0.333],[3.849,-0.339],[3.861,-0.332],[3.904,-0.332],[4.051,-0.332],[4.057,-0.338],[4.1,-0.338],[4.112,-0.332],[4.149,-0.331],[4.155,-0.338],[4.21,-0.337],[4.228,-0.331],[4.234,-0.337],[4.295,-0.337],[4.314,-0.331],[4.344,-0.331],[4.35,-0.337],[4.442,-0.336],[4.448,-0.33],[4.454,-0.336],[4.491,-0.336],[4.497,-0.33],[4.564,-0.336],[4.68,-0.336],[4.686,-0.33],[4.735,-0.329],[4.742,-0.335],[4.766,-0.335],[4.833,-0.329],[4.882,-0.335],[4.888,-0.329],[4.913,-0.329],[4.931,-0.329],[4.937,-0.335],[6.984,-0.327],[6.991,-0.333],[7.088,-0.339],[7.095,-0.345],[7.131,-0.345],[7.168,-0.357],[7.192,-0.357],[7.247,-0.375],[7.266,-0.375],[7.284,-0.387],[7.327,-0.393],[7.345,-0.406],[7.364,-0.405],[7.382,-0.418],[7.419,-0.424],[7.425,-0.43],[8.042,-0.428],[8.063,-0.4],[8.063,-0.369],[8.072,-0.36],[8.097,-0.36],[8.109,-0.378],[8.354,-0.371],[8.415,-0.371],[8.421,-0.377],[9.625,-0.373],[9.637,-0.367],[9.643,-0.373],[9.741,-0.373],[9.747,-0.366],[9.765,-0.372],[9.998,-0.372],[10.022,-0.359],[10.92,-0.356],[10.927,-0.362],[10.982,-0.362],[10.988,-0.356],[11.03,-0.356],[11.061,-0.343],[11.599,-0.341],[11.626,-0.308],[11.638,-0.247],[11.653,-0.237],[11.684,-0.237],[11.696,-0.225],[11.708,-0.225],[11.727,-0.237],[11.733,-0.225],[11.77,-0.231],[11.782,-0.219],[11.788,-0.231],[11.8,-0.231],[11.812,-0.218],[11.831,-0.237],[11.843,-0.224],[11.873,-0.23],[11.886,-0.218],[11.892,-0.23],[11.91,-0.23],[11.922,-0.218],[11.935,-0.23],[11.947,-0.23],[11.959,-0.218],[11.965,-0.23],[11.996,-0.224],[12.002,-0.23],[12.02,-0.23],[12.032,-0.218],[12.038,-0.23],[12.057,-0.23],[12.069,-0.218],[12.075,-0.23],[12.093,-0.23],[12.1,-0.217],[12.106,-0.217],[12.112,-0.23],[12.142,-0.223],[12.148,-0.229],[12.167,-0.229],[12.179,-0.223],[12.197,-0.229],[12.216,-0.217],[12.228,-0.223],[12.258,-0.18],[12.258,0.21],[12.245,0.235],[12.232,0.235],[12.214,0.254],[12.196,0.241],[12.171,0.253],[12.159,0.241],[12.141,0.253],[12.128,0.235],[12.11,0.253],[12.098,0.253],[12.086,0.241],[12.067,0.253],[12.049,0.241],[12.037,0.253],[12.025,0.253],[12.018,0.241],[12.012,0.241],[12,0.253],[11.976,0.241],[11.963,0.253],[11.951,0.253],[11.945,0.24],[11.939,0.24],[11.921,0.253],[11.908,0.234],[11.89,0.252],[11.878,0.246],[11.847,0.252],[11.835,0.24],[11.829,0.24],[11.823,0.252],[11.811,0.252],[11.792,0.24],[11.78,0.252],[11.762,0.24],[11.749,0.252],[11.725,0.24],[11.707,0.252],[11.695,0.246],[11.652,0.252],[11.636,0.267],[11.63,0.316],[11.618,0.34],[11.596,0.355],[11.046,0.353],[11.022,0.365],[10.46,0.363],[10.453,0.37],[10.417,0.369],[10.411,0.363],[10.405,0.369],[10.288,0.369],[10.062,0.362],[10.056,0.368],[10.013,0.368],[10.007,0.374],[9.952,0.374],[9.946,0.38],[9.891,0.38],[9.885,0.374],[9.867,0.374],[9.824,0.373],[9.818,0.379],[9.677,0.379],[9.665,0.373],[9.659,0.379],[9.5,0.378],[9.494,0.372],[9.451,0.372],[9.445,0.378],[8.162,0.374],[8.155,0.38],[8.137,0.373],[8.131,0.38],[8.125,0.373],[8.106,0.373],[8.088,0.361],[8.067,0.37],[8.054,0.407],[8.039,0.422],[8.021,0.428],[7.416,0.426],[7.342,0.401],[7.324,0.389],[7.306,0.389],[7.239,0.364],[7.214,0.364],[7.184,0.352],[7.159,0.352],[7.153,0.345],[7.123,0.345],[7.117,0.339],[7.08,0.339],[7.074,0.333],[7.025,0.333],[7.019,0.327],[5.998,0.323],[5.98,0.329],[5.961,0.323],[5.943,0.329],[5.913,0.323],[5.906,0.329],[5.619,0.328],[5.613,0.334],[5.595,0.328],[5.466,0.327],[5.436,0.327],[5.43,0.333],[4.446,0.33],[4.44,0.336],[3.627,0.333],[3.621,0.339],[3.608,0.333],[3.602,0.339],[2.93,0.336],[2.924,0.343],[2.698,0.342],[2.692,0.348],[2.661,0.348],[2.624,0.36],[2.588,0.36],[2.551,0.372],[2.453,0.384],[2.447,0.39],[2.423,0.39],[2.386,0.402],[2.319,0.408],[2.288,0.42],[2.221,0.426],[2.19,0.438],[2.117,0.444],[2.086,0.456],[2.056,0.456],[2.019,0.468],[1.921,0.48],[1.884,0.492],[1.835,0.491],[1.829,0.498],[1.334,0.496],[1.328,0.502],[1.206,0.501],[1.2,0.526],[1.194,0.514],[1.185,0.511],[1.181,0.532],[1.178,0.511],[1.169,0.501],[1.16,0.517],[1.166,0.523],[1.166,0.553],[1.178,0.584],[1.169,0.593],[1.065,0.593],[1.053,0.586],[1.047,0.574],[1.038,0.571],[1.035,0.501],[0.9,0.5],[0.888,0.513],[0.876,0.506],[0.858,0.506],[0.851,0.512],[0.845,0.506],[0.534,0.505],[0.485,0.505],[0.479,0.511],[0.473,0.505],[0.448,0.505],[0.442,0.511],[0.369,0.511],[0.35,0.505],[0.344,0.511],[0.057,0.51]],"scaleRefs":["bcm-115-carbine-barrel.flange_od"],"inputs":{"bcm-115-carbine-barrel.flange_od":1.186,"bcm-115-carbine-barrel.outline_front_face":12.258,"bcm-115-carbine-barrel.outline_rear_face":0.046},"tolerance":0.004,"photo":"references/bcm-115-carbine-barrel 4e5aad5ce36e (Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, 2200 x 1467)","method":"luminance < 200, 1 boxes excluded, largest piece, holes filled; rotated +0.2° as declared; scale from bcm-115-carbine-barrel.flange_od = 1.186 in (y-extent 194 px → 163.6 px/in); origin at x min, y center of the outline; clipped to x min {.outline_rear_face} = 0.046, x max {.outline_front_face} = 12.258; Douglas-Peucker at 0.004 in with the extremes kept: 345 points (IoU 0.999 with the full outline); The indexing pin (columns 247 to 265 of the upper edge) is boxed out: it is a pin, not a ring.; checks: centre between the top (max over 0.4 in windows) along x [2.9, 6.8] 0.001 ± 0.018; centre between the top (max over 0.4 in windows) along x [10.1, 11.5] 0.004 ± 0.018; height (tooth tops, max over 0.02 in windows) along x [8.3, 9.8] 0.751 ± 0.019; height (tooth tops, max over 0.02 in windows) along x [0.2, 0.8] 1.003 ± 0.020 (tools/trace.py)","via":"harvest","note":"Black on white, cut out: the outline is the silhouette's, in its own unit (the journal reads .750 in it). The model's stations are read through the photo's calibration (outline_lens_x, outline_yaw_run: the barrel leans a little to the lens; outline_inset: the cut-out's edge), with the length between its end faces set to the published one. Taken from about 65 in: a step's rim rounds the outline by two hundredths of an inch at most, and the corners it shows broken (the collar's front, the journal's front, the shoulder) are broken."}},"gaps":[{"what":"The gas port's place, to better than a fortieth of an inch","need":"BCM's figure, or a photo with the port square to the lens and the collar's face in it (it is read here off two nicks a fraction of a pixel deep in the silhouette's edges; BCM's own gas block has its port 0.275 in ahead of its rear face, and this barrel's reads 0.26 ahead of the collar)"},{"what":"Where the 11.5 in is measured from","need":"BCM's statement (taken from the barrel's breech end, as the Army's drawing dimensions a barrel; from the bolt's face it would be an eighth shorter overall)"},{"what":"The dimple under the journal: its depth","need":"BCM's figure, or a photo of the journal's underside lit from the side (its width is on the silhouette, 0.144 in)"},{"what":"The gas port's diameter","need":"BCM's figure (.078 is read on an oblique close photo, ± .012; a mid-length chart has .075)"},{"what":"The extension's locking lugs and feed ramps, and the chamber's mouth","need":"The extension's drawing (8448550 isn't in the package): its inside is the reference CAD set's, turned; hidden once the barrel is in a receiver"}]},"bcm-145-mid-barrel":{"id":"bcm-145-mid-barrel","name":"Standard 14.5\" Mid Length Barrel, Stripped","manufacturer":"BCM","sku":"BCM-BRL-s-MID-14-STD","url":"https://bravocompanyusa.com/bcm-standard-14-5-mid-length-barrel-stripped/","category":"barrel","description":"Bravo Company's 14.5 in government-profile barrel, stripped: MIL-B-11595E chrome moly vanadium steel, a chrome lined 5.56 NATO chamber and bore, 1/7 twist, manganese phosphate, a mid-length gas port drilled and dimpled on a .750 in journal, an M4 feed ramp extension, a 1/2-28 muzzle thread.","weight":"bcm-145-mid-barrel.weight","barrelLength":"bcm-145-mid-barrel.length","cartridge":{"takes":["5.56 NATO"],"stated":"5.56 NATO Chambers","source":"https://bravocompanyusa.com/bcm-standard-14-5-mid-length-barrel-stripped/ (a heading of BCM's description, as cached: harvest.quote; the seller Primary Arms has \"Chambered in 5.56 NATO, 1:7 twist\" for the same number)"},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"extension":{"origin":[0,0,0],"note":"The barrel extension's flange, its rear face, on the bore axis, +x toward the muzzle."},"muzzle":{"origin":["{.shoulder_x}",0,0]},"gas_journal":{"origin":["{.gas_port_x}",0,0]}},"interfaces":{"barrel_extension":{"type":"ar15.barrel_extension","role":"barrel","anchor":"extension","params":{},"flips":false,"note":"BCM: \"M4 Feed Ramp Barrel Extension (USGI)\"."},"muzzle":{"type":"muzzle_thread","role":"barrel","anchor":"muzzle","params":{"thread":"1/2-28","thread_length":"={.thread_length}"},"flips":false,"note":"The thread is the seller's statement, not the maker's: Primary Arms, for this number, \"Threaded 1/2x28\" and \"Thread Pattern 1/2 X 28\"; BCM's barrel page states none. Its length is read off the photo (0.614 ± 0.03 in; the Army barrel's is .63)."},"gas_journal":{"type":"ar15.gas_journal","role":"barrel","anchor":"gas_journal","params":{"journal_od":"={.journal_od}"},"flips":false,"note":"BCM: \"(.750) at Gas Block location\"; \"gas ports installed and dimpled for a strong gas block installation\". The journal runs from 8.81 to 10.74 in ahead of the receiver's face, the port 0.29 in ahead of its rear shoulder."},"gas_system":{"type":"ar15.gas_system","role":"barrel","params":{"length":"mid"},"flips":false,"note":"BCM names it \"Standard 14.5\" Mid Length Barrel, Stripped\" and says \"These are stripped 14.5\" Mid Length Standard 11595E barrels\" (https://bravocompanyusa.com/bcm-standard-14-5-mid-length-barrel-stripped/); Primary Arms' table for the same number: \"Gas System Length Mid-Length\". What the platform checks a gas tube against a barrel by (D83)."}},"materials":{"barrel":{"label":"Barrel","finish":"phosphate","recolorable":false,"color":"steel-phosphate-charcoal","note":"BCM: \"Manganese Phosphate Barrel Finish\" and \"Barrels are parkerized with the manganese phosphate finish per Mil-Spec\" (https://bravocompanyusa.com/bcm-standard-14-5-mid-length-barrel-stripped/); Primary Arms' table: \"Barrel Coating Manganese Phosphate\". The one finish this number is sold in. One slot: in Primary Arms' three photos the extension, its index pin, the collar, the journal and the two sections ahead of it are one matte charcoal (the whole barrel reads #434046 in its level view, c7e2f77b39f5; the section under the handguard #403c42, the journal #3f3b41; #403c41 and #444149 in its three-quarter view, 3125b323603d), within ten levels of what the 16 in barrel's photos read and its preset was fitted to (#3f3f3e), with a blue cast of the photographer's; the thread reads darker (#262428) for its shadowed roots. Not drawn: the chrome of the bore and the chamber (\"Chrome Bore and Chamber\": inside), the stamped \"HP MP 1/7 5.56 NATO\"."}},"components":{},"geometry":{"model":"bcm-145-mid-barrel.glb","components":{},"approximations":["Turned from stations read off Primary Arms' level photo of this barrel: each section's diameter and each step's place, through the photo's calibration (the lens 16 to 17 in off opposite the picture's middle; the barrel leaning 1.9° to it, its scale 3% larger at the muzzle than at the breech; the cut-out's edge 0.8 px inside the barrel's). Three knowns fix that calibration: the extension's body at the Army drawing's .999, the journal at the published .750, the length at the published one (14.5 in from its breech end, with the extension's half inch behind that: 15.00). The same photo's traced outline, mapped through it, lies within 0.012 in of the turned profile wherever it is clear of a step.","Lengths along the barrel are good to about a twentieth of an inch: the thread's own pitch in the photo has the muzzle end's scale 1.3% smaller than the calibration does, and the two known diameters alone, with no allowance for the cut-out's edge, have the barrel 1.5% longer than published (a black tube reads thin on white).","Every step is square at the face read off the photo, which rounds each by its rim's arc (the lens saw the ends from 24° off square): the face is where the arc begins. The taper ahead of the chamber is a straight cone, the section under the handguard a cone (.675 to .651 in), the ramp up to the collar an arc through its two ends and a station between; the last section, whose edges open 0.009 in toward the shoulder in the photo, is a cylinder at its middle's diameter.","The indexing pin at the reference CAD set's .125, where the photo has it behind the flange, as high as the 16 in barrel's own photo has its pin (no photo of this barrel shows it in profile); the gas port at a mid-length chart's .075, on top of the journal where the photo has its mouth; the bore one plain hole right through, at the Army drawing's .219; the extension's rear opening turned at the reference CAD set's sizes (its chamfered mouth, the ring its locking lugs make, the recess ahead of them).","The muzzle thread is a helix, 28 to the inch, between the minor and major diameters of the Army barrel's 1/2-28 thread (the seller states 1/2 X 28): a plain V without the flats of its form, right-hand (assumed: its designation marks no other), running out at the shoulder over its last pitch, with no relief there or chamfer at the muzzle.","Not drawn: the dimple under the journal opposite the port and the relief groove at the collar's front face (neither's depth is sourced), the breaks at the extension's rear corner and the muzzle's crown, the chamber, the slots between the extension's locking lugs and its feed ramps (the lugs are one ring), the marking ahead of the journal (HP MP 1/7 5.56 NATO)."],"ledger":["bcm-145-mid-barrel.length","bcm-145-mid-barrel.overall_length","bcm-145-mid-barrel.extension_rear_x","bcm-145-mid-barrel.flange_front_x","bcm-145-mid-barrel.shoulder_x","bcm-145-mid-barrel.thread_length","bcm-145-mid-barrel.gas_port_x","bcm-145-mid-barrel.journal_od","bcm-145-mid-barrel.muzzle_od"]},"profiles":{"side":{"plane":"xy","origin":"the silhouette's rear tip, on the axis; the outline begins at the extension's rear face","offset":{"x":"extension_rear_x"},"points":[[0.213,0.478],[0.213,-0.488],[0.229,-0.496],[1.058,-0.492],[1.112,-0.553],[1.158,-0.576],[1.288,-0.575],[1.296,-0.567],[1.311,-0.567],[1.342,-0.552],[1.391,-0.501],[1.403,-0.482],[1.939,-0.48],[1.947,-0.472],[2.054,-0.464],[2.062,-0.456],[2.093,-0.456],[2.1,-0.448],[2.139,-0.448],[2.146,-0.44],[2.185,-0.44],[2.192,-0.432],[2.277,-0.424],[2.284,-0.417],[2.353,-0.409],[2.361,-0.401],[2.399,-0.401],[2.407,-0.393],[2.438,-0.393],[2.445,-0.385],[2.476,-0.385],[2.484,-0.377],[2.522,-0.377],[2.53,-0.369],[2.606,-0.361],[2.614,-0.354],[2.652,-0.353],[2.66,-0.346],[2.706,-0.345],[2.713,-0.338],[2.752,-0.338],[2.759,-0.33],[5.705,-0.315],[5.712,-0.323],[5.72,-0.315],[6.165,-0.313],[6.172,-0.321],[7.246,-0.315],[7.254,-0.308],[7.384,-0.307],[7.392,-0.315],[8.312,-0.31],[8.32,-0.318],[8.964,-0.315],[8.972,-0.322],[9.026,-0.322],[9.033,-0.33],[9.072,-0.329],[9.079,-0.337],[9.11,-0.337],[9.118,-0.344],[9.148,-0.344],[9.156,-0.352],[9.187,-0.352],[9.194,-0.359],[9.233,-0.367],[9.241,-0.375],[9.279,-0.382],[9.287,-0.39],[9.325,-0.397],[9.348,-0.412],[9.455,-0.412],[9.463,-0.419],[9.985,-0.417],[9.996,-0.405],[10.004,-0.375],[10.015,-0.363],[10.291,-0.362],[10.299,-0.369],[10.514,-0.368],[10.521,-0.361],[10.537,-0.368],[11.357,-0.364],[11.365,-0.372],[11.956,-0.369],[11.971,-0.353],[12.316,-0.352],[12.324,-0.359],[13.367,-0.354],[13.374,-0.362],[13.474,-0.361],[13.482,-0.354],[13.566,-0.353],[13.574,-0.361],[14.134,-0.358],[14.149,-0.35],[14.348,-0.349],[14.356,-0.357],[14.379,-0.357],[14.387,-0.349],[14.41,-0.349],[14.418,-0.357],[14.433,-0.349],[14.471,-0.349],[14.487,-0.349],[14.494,-0.356],[14.717,-0.355],[14.751,-0.328],[14.774,-0.274],[14.8,-0.247],[14.847,-0.247],[14.854,-0.255],[14.885,-0.247],[14.893,-0.255],[14.908,-0.247],[14.923,-0.247],[14.931,-0.254],[14.939,-0.247],[15,-0.246],[15.015,-0.254],[15.031,-0.246],[15.038,-0.254],[15.054,-0.254],[15.307,-0.253],[15.323,-0.245],[15.323,0.235],[15.251,0.238],[15.243,0.246],[15.235,0.238],[15.22,0.246],[14.798,0.244],[14.779,0.263],[14.756,0.316],[14.729,0.343],[14.713,0.343],[14.706,0.35],[14.13,0.348],[14.1,0.363],[11.975,0.36],[11.944,0.383],[10.97,0.378],[10.962,0.386],[10.947,0.386],[10.94,0.378],[10.894,0.378],[10.886,0.385],[10.019,0.381],[10,0.4],[10,0.423],[9.988,0.435],[9.344,0.431],[9.298,0.408],[9.26,0.4],[9.229,0.385],[9.214,0.385],[9.206,0.377],[9.153,0.369],[9.145,0.361],[9.068,0.353],[9.061,0.346],[8.999,0.345],[8.992,0.338],[8.869,0.337],[8.861,0.329],[8.846,0.329],[8.838,0.337],[8.493,0.327],[8.485,0.335],[7.519,0.33],[7.511,0.338],[6.292,0.332],[6.284,0.34],[4.942,0.333],[4.934,0.341],[4.858,0.34],[4.85,0.332],[4.796,0.332],[4.789,0.34],[4.766,0.332],[4.75,0.332],[4.743,0.34],[4.727,0.332],[4.72,0.339],[3.101,0.331],[3.094,0.339],[2.963,0.338],[2.956,0.331],[2.771,0.33],[2.764,0.337],[2.741,0.337],[2.733,0.345],[2.687,0.345],[2.679,0.352],[2.649,0.352],[2.641,0.36],[2.61,0.36],[2.603,0.367],[2.564,0.367],[2.557,0.375],[2.526,0.375],[2.518,0.382],[2.487,0.382],[2.48,0.39],[2.411,0.397],[2.403,0.405],[2.365,0.405],[2.357,0.412],[2.319,0.412],[2.311,0.42],[2.273,0.419],[2.265,0.427],[2.226,0.427],[2.219,0.434],[2.188,0.434],[2.18,0.442],[2.119,0.449],[2.111,0.457],[2.073,0.457],[2.065,0.464],[2.035,0.464],[2.027,0.472],[1.996,0.472],[1.988,0.479],[1.889,0.479],[1.881,0.486],[1.843,0.486],[1.666,0.485],[1.659,0.478],[1.413,0.477],[1.398,0.484],[1.344,0.545],[1.305,0.568],[1.275,0.568],[1.267,0.575],[1.221,0.575],[1.213,0.568],[1.206,0.575],[1.19,0.575],[1.183,0.567],[1.152,0.567],[1.144,0.56],[1.129,0.559],[1.091,0.521],[1.083,0.521],[1.079,0.509],[1.053,0.482],[1.037,0.482],[1.03,0.49],[0.884,0.489],[0.224,0.486]],"scaleRefs":["bcm-145-mid-barrel.flange_od"],"inputs":{"bcm-145-mid-barrel.flange_od":1.151,"bcm-145-mid-barrel.outline_front_face":15.323,"bcm-145-mid-barrel.outline_rear_face":0.213},"tolerance":0.004,"photo":"references/bcm-145-mid-barrel c7e2f77b39f5 (Primary Arms' gallery, BCM-BRL-S-MID-14-STD_02: the barrel level on white, from above, 2200 x 1467)","method":"luminance < 200, largest piece, holes filled; rotated +0.3° as declared; scale from bcm-145-mid-barrel.flange_od = 1.151 in (y-extent 150 px → 130.4 px/in); origin at x min, y center of the outline; clipped to x min {.outline_rear_face} = 0.213, x max {.outline_front_face} = 15.323; Douglas-Peucker at 0.004 in with the extremes kept: 250 points (IoU 0.997 with the full outline); Seen from above: the indexing pin and the gas port face the lens and aren't on the silhouette.; checks: centre between the top (max over 0.4 in windows) along x [2.9, 8.5] 0.010 ± 0.023; centre between the top (max over 0.4 in windows) along x [12.2, 14.4] 0.003 ± 0.023; height (tooth tops, max over 0.02 in windows) along x [10.3, 11.8] 0.749 ± 0.024; height (tooth tops, max over 0.02 in windows) along x [0.4, 0.95] 0.982 ± 0.024 (tools/trace.py)","via":"harvest","note":"Black on white, cut out: the outline is the silhouette's, in its own unit (the journal reads .750 in it). The photo was taken from 16 to 17 in, and the barrel leans to it: the model takes that out (outline_lens_x, outline_yaw_run), and the cut-out's edge (outline_inset), and sets the length between its end faces to the published one. Each step's corner is rounded by its rim's arc: the lens sees the ends from 24 degrees off square."}},"gaps":[{"what":"The scale along the barrel, to better than 1%","need":"A maker's drawing, or a side photo taken square from a distance with a scale in the barrel's plane: the published length, the thread's pitch and the two known diameters are 1.3 to 1.5% apart in this photo"},{"what":"Where the 14.5 in is measured from","need":"BCM's statement (taken from the barrel's breech end, as the Army's drawing dimensions a barrel; from the bolt's face it would be an eighth shorter overall)"},{"what":"The dimple under the journal and the relief groove at the collar's front face: their sizes and depths","need":"BCM's figures, or a side photo with the dimple on the silhouette (Primary Arms' close view of the journal shows both from above)"},{"what":"The gas port's diameter","need":"BCM's figure (.075 is a third-party chart's)"},{"what":"The indexing pin's height","need":"A side photo of this barrel with the pin on the silhouette (the 16 in barrel's reading stands in: the same USGI extension by BCM's words)"},{"what":"The extension's locking lugs and feed ramps, and the chamber's mouth","need":"The extension's drawing (8448550 isn't in the package): its inside is the reference CAD set's, turned; hidden once the barrel is in a receiver"}]},"bcm-16-mid-barrel":{"id":"bcm-16-mid-barrel","name":"Standard 16\" Mid Length Barrel, Stripped","manufacturer":"BCM","sku":"BCM-BRL-s-MID-16-STD","url":"https://bravocompanyusa.com/bcm-standard-16-mid-length-barrel-stripped/","category":"barrel","description":"Bravo Company's 16 in government-profile barrel, stripped: MIL-B-11595E chrome moly vanadium steel, a chrome lined 5.56 NATO chamber and bore, 1/7 twist, manganese phosphate, a mid-length gas port drilled and dimpled on a .750 in journal, an M4 feed ramp extension, a 1/2-28 muzzle thread.","weight":"bcm-16-mid-barrel.weight","barrelLength":"bcm-16-mid-barrel.length","cartridge":{"takes":["5.56 NATO"],"stated":"5.56 NATO Chambers","source":"https://bravocompanyusa.com/bcm-standard-16-mid-length-barrel-stripped/ (a heading of BCM's description, as cached: harvest.quote; the seller Primary Arms has \"Chambered in 5.56 NATO, 1:7 twist\" for the same number)"},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"extension":{"origin":[0,0,0],"note":"The barrel extension's flange, its rear face, on the bore axis, +x toward the muzzle."},"muzzle":{"origin":["{.shoulder_x}",0,0]},"gas_journal":{"origin":["{.gas_port_x}",0,0]}},"interfaces":{"barrel_extension":{"type":"ar15.barrel_extension","role":"barrel","anchor":"extension","params":{},"flips":false,"note":"BCM: \"M4 Feed Ramp Barrel Extension (USGI)\"."},"muzzle":{"type":"muzzle_thread","role":"barrel","anchor":"muzzle","params":{"thread":"1/2-28","thread_length":"={.thread_length}"},"flips":false,"note":"The thread is the seller's statement, not the maker's: Primary Arms, for this number, \"Threaded 1/2x28\" and \"Thread Pattern 1/2 X 28\"; BCM's page states none. Its length is read off the photo (0.50 ± 0.04 in), shorter than the Army barrel's .63."},"gas_journal":{"type":"ar15.gas_journal","role":"barrel","anchor":"gas_journal","params":{"journal_od":"={.journal_od}"},"flips":false,"note":"BCM: \"(.750) at Gas Block location\"; \"gas ports installed and dimpled for a strong gas block installation\". The journal runs from 8.85 to 10.72 in ahead of the receiver's face, the port 0.28 in ahead of its rear shoulder."},"gas_system":{"type":"ar15.gas_system","role":"barrel","params":{"length":"mid"},"flips":false,"note":"BCM names it \"Standard 16\" Mid Length Barrel\". What the platform checks a gas tube against a barrel by (D83)."}},"materials":{"barrel":{"label":"Barrel","finish":"phosphate","recolorable":false,"color":"steel-phosphate-charcoal","note":"BCM: \"Manganese Phosphate Barrel Finish\" and \"Barrels are parkerized with the manganese phosphate finish per Mil-Spec\"; Primary Arms' table: \"Barrel Coating Manganese Phosphate\". The one finish this number is sold in. One slot: in Primary Arms' six photos the extension, its index pin, the journal and the thread are the barrel's own matte charcoal (the extension reads #393838 beside the barrel's #3a3a38 in its side view, 99b8653ffc94). Not drawn: the chrome of the bore and the chamber (\"Chrome Bore and Chamber\": inside), the stamped \"HP MP 1/7 5.56 NATO\"."}},"components":{},"geometry":{"model":"bcm-16-mid-barrel.glb","components":{},"approximations":["Turned from its side outline, traced from Primary Arms' photo of this barrel, extension to muzzle: its diameters at the scale its gas block journal's .750 gives, its length at the published one (16 in from its breech end, with the extension's half inch behind that: 16.50). The two scales differ by 2.5%: a black tube reads thin on white.","The photo isn't square to the barrel: its breech end stands a little nearer the lens than its journal, so diameters behind the journal are up to 1.2% large (the extension's body is drawn 1.011 in across where its drawing allows .999) and ahead of it up to 0.7% small. Not corrected.","The flange and the muzzle shoulder are squared at the faces read off the photo (it rounds every corner by its rim's arc: the lens saw the ends from 13° and 16° off square); the other steps keep the photo's rounding, 0.02 in at most.","The indexing pin at the reference CAD set's .125, where and as high as the photo has it; the gas port at a mid-length chart's .075, on top of the journal where the photo's edges are nicked; the bore one plain hole right through, at the Army drawing's .219; the extension's rear opening turned at the reference CAD set's sizes (its chamfered mouth, the ring its locking lugs make, the recess ahead of them).","The muzzle thread is a helix, 28 to the inch, between the minor and major diameters of the Army barrel's 1/2-28 thread (the seller states 1/2 X 28): a plain V without the flats of its form, right-hand (assumed: its designation marks no other), running out at the shoulder over its last pitch, with no relief there or chamfer at the muzzle. Rings until 2026-10-06.","Not drawn: the dimple under the journal opposite the port (its depth isn't sourced), the chamber, the slots between the extension's locking lugs and its feed ramps (the lugs are one ring), the marking ahead of the journal (HP MP 1/7 5.56 NATO)."],"ledger":["bcm-16-mid-barrel.overall_length","bcm-16-mid-barrel.extension_rear_x","bcm-16-mid-barrel.flange_front_x","bcm-16-mid-barrel.shoulder_x","bcm-16-mid-barrel.gas_port_x","bcm-16-mid-barrel.journal_od","bcm-16-mid-barrel.muzzle_od"]},"profiles":{"side":{"plane":"xy","origin":"the silhouette's rear tip, on the axis; the outline begins at the extension's rear face","offset":{"x":"extension_rear_x"},"points":[[0.112,0.503],[0.112,-0.487],[0.117,-0.504],[1.05,-0.502],[1.081,-0.567],[1.101,-0.588],[1.231,-0.593],[1.262,-0.565],[1.291,-0.497],[1.909,-0.493],[2.75,-0.34],[9.074,-0.326],[9.163,-0.334],[9.292,-0.357],[9.407,-0.387],[9.529,-0.429],[9.706,-0.43],[10.147,-0.426],[10.16,-0.405],[10.173,-0.359],[10.18,-0.359],[10.195,-0.374],[11.797,-0.374],[12.079,-0.372],[12.094,-0.357],[12.319,-0.355],[14.951,-0.357],[15.191,-0.352],[15.872,-0.352],[15.902,-0.341],[16.42,-0.341],[16.457,-0.33],[16.477,-0.31],[16.504,-0.262],[16.507,-0.244],[16.517,-0.238],[16.927,-0.241],[17.005,-0.234],[17.005,0.243],[16.586,0.239],[16.512,0.243],[16.492,0.293],[16.474,0.319],[16.454,0.336],[16.428,0.343],[15.895,0.347],[15.877,0.354],[14.707,0.362],[14.393,0.357],[14.112,0.362],[13.801,0.357],[13.412,0.363],[13.068,0.358],[12.102,0.361],[12.076,0.376],[11.732,0.378],[10.544,0.375],[10.204,0.381],[10.174,0.366],[10.165,0.375],[10.154,0.42],[10.137,0.429],[9.538,0.433],[9.508,0.43],[9.367,0.379],[9.278,0.357],[9.175,0.339],[9.056,0.329],[2.773,0.341],[1.893,0.499],[1.29,0.499],[1.281,0.504],[1.266,0.545],[1.248,0.564],[1.251,0.571],[1.227,0.592],[1.109,0.592],[1.081,0.572],[1.077,0.539],[1.059,0.535],[1.057,0.504],[0.694,0.506]],"scaleRefs":["bcm-16-mid-barrel.flange_od"],"inputs":{"bcm-16-mid-barrel.flange_od":1.185,"bcm-16-mid-barrel.outline_front_face":17.005,"bcm-16-mid-barrel.outline_rear_face":0.112},"tolerance":0.004,"photo":"references/bcm-16-mid-barrel 99b8653ffc94 (Primary Arms' gallery, BCM-BRL-S-MID-16-STD_01: the barrel from the side on white, 4848 x 3232)","method":"luminance < 200, 2 boxes excluded, largest piece, holes filled; rotated -0.4° as declared; scale from bcm-16-mid-barrel.flange_od = 1.185 in (y-extent 320 px → 270.2 px/in); origin at x min, y center of the outline; clipped to x min {.outline_rear_face} = 0.112, x max {.outline_front_face} = 17.005; Douglas-Peucker at 0.004 in with the extremes kept: 82 points (IoU 0.996 with the full outline); The indexing pin (columns 372 to 408 of the upper edge) is boxed out: it is a pin, not a ring.; checks: centre between the top (max over 0.4 in windows) along x [2.6, 8.6] 0.002 ± 0.011; centre between the top (max over 0.4 in windows) along x [11.2, 15.8] 0.003 ± 0.011; height (tooth tops, max over 0.02 in windows) along x [10.6, 11.9] 0.750 ± 0.012 (tools/trace.py)","via":"harvest","note":"Black on white, cut out: the outline is the silhouette's. Its diameters are at the journal's scale (a black tube reads thin on white, which a diameter's scale takes out); its length is stretched to the published one. Each shoulder's corner is rounded by its rim's arc (the lens sees the ends from 13° and 16° off square): by 0.06 in at the flange, 0.07 at the muzzle shoulder, 0.02 elsewhere."}},"gaps":[{"what":"The muzzle end's scale, and with it the thread's length","need":"The thread's own pitch reads 9.2 px in the photo where 28 to the inch would be 9.8 at the published length's scale: 6% short, unexplained. A maker's drawing, or a straight side photo of the muzzle with a scale in its plane"},{"what":"Where the 16 in is measured from","need":"BCM's statement (taken from the barrel's breech end, as the Army's drawing dimensions a barrel; from the bolt's face it would be an eighth shorter overall)"},{"what":"The dimple under the journal: its diameter and depth","need":"BCM's figure, or a side photo with the dimple on the silhouette (it dents the lower edge by half a pixel here)"},{"what":"The gas port's diameter","need":"BCM's figure (.075 is a third-party chart's)"},{"what":"The extension's locking lugs and feed ramps, and the chamber's mouth","need":"The extension's drawing (8448550 isn't in the package): its inside is the reference CAD set's, turned; hidden once the barrel is in a receiver"}]},"bcm-625-gas-block":{"id":"bcm-625-gas-block","name":"Low Profile Gas Block (steel with set screws) 625","manufacturer":"BCM","sku":"BCM-LGB-625","url":"https://bravocompanyusa.com/bcm-low-profile-gas-block-steel-with-set-screws-625/","category":"gas_block","description":"Bravo Company's low-profile gas block for a .625 in journal, the journal of a pencil-profile barrel: steel, phosphate finish, its bore honed after finishing, held by two 10-32 x 3/16 knurled cup point set screws. The gas tube's roll pin isn't included.","weight":"bcm-625-gas-block.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"journal":{"origin":[0,0,0],"note":"On the bore axis at the gas port, +x toward the muzzle. The port is where the standard tube's gas hole lands with its pin in the block's cross hole: 0.276 in ahead of the rear face (port_from_rear)."},"gas_tube":{"origin":[0,"{.tube_hole_above_bore}",0],"x":[-1,0,0],"note":"The tube's hole at the port, +x rearward toward the receiver: the Army's height for the tube at the block (.625 above the bore), which the roll pin's hole in the side photo agrees with."}},"interfaces":{"gas_journal":{"type":"ar15.gas_journal","role":"block","anchor":"journal","params":{"journal_od":"={.journal_id}"},"flips":false,"note":"BCM: \"Machined of steel, phosphate finish, for .625 barrels.\" and \"Barrel ID honed after finish per USGI TDP.\" Mounted by set screws (BCM: \"Made by Bravo Company MFG, Inc. with set screw mounting. Set Screws are Steel 10-32 x 3/16 Knurled Cup Point\"; Primary Arms: \"Two 10-32 x 3/16 knurled cup point set screws included\" and \"Low profile for use under free float handguards\"). Primary Arms: \"This version is sized for a .625\" gas block journal.\" A barrel with the commoner .750 journal doesn't go into it."},"gas_tube":{"type":"ar15.gas_tube","role":"block","anchor":"gas_tube","params":{},"flips":false,"note":"Primary Arms: \"This gas block does not include a gas tube roll pin, so plan to reuse the one from your existing gas tube or pick one up separately.\""}},"materials":{"body":{"label":"Gas block","finish":"phosphate","recolorable":false,"color":"steel-phosphate-black","note":"BCM: \"Machined of steel, phosphate finish\"; Primary Arms: \"Steel construction with a phosphate finish\"; MidwayUSA: \"Black Phosphate\". One finish: no colourways. The black phosphate matched on Primary Arms' photos of the .750 block from the same studio (data/colors/steel.yaml, steel-phosphate-black: #222320 and #2c2c2b there); this block's own read the same, #272727 on its side view (4f19e3379457) and #303030 on the star face of its oblique view (453104958d81). The two set screws (\"Steel 10-32 x 3/16 Knurled Cup Point\") aren't drawn."},"bore":{"label":"Bore","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"BCM: \"Barrel ID honed after finish per USGI TDP.\": the bore's wall is bare steel, bright against the black phosphate in every photo of the block's face (Primary Arms' 453104958d81, BCM's own f006626e492d). On a barrel it is out of sight; it shows in the exploded view. Bright metal isn't fitted to a photo: the app's natural stainless. The faces of the body's mesh that lie on the bore."},"marking":{"label":"Star","finish":"steel","recolorable":false,"color":"stainless-natural","note":"BCM's star, laser-marked light grey on the front face (Primary Arms' oblique view, 453104958d81; BCM's own picture). A mark, drawn because it is the block's one feature from the front: the app's natural-steel grey, not matched to a photo."}},"components":{},"geometry":{"model":"bcm-625-gas-block.glb","components":{},"approximations":["Its section is read off an oblique photo of the star face turned square by the block's own bore (the bore's mouth is a circle in the face's plane, so its ellipse in the photo fixes the turn; the face's own axis is set upright) and scaled by a height of 1.34 in, which a parts database states for this number and the bore itself bears out (1.33 by the mouth as .625): no straight end view is on file. The outline's left side is the face's edge against the white ground; its right side, where the block's own side stands behind the face in the photo, is the left's mirror about the axis. Good to about 0.012 in round it.","By its own photos it has the .750 block's outside, bored smaller: the boss's top, the flat, the star, the length and the roll pin's place each within a hundredth of that block's. Its ring reads 0.03 in narrower across (0.85 against 0.88 ± 0.025): drawn as read on its own photo.","The section is run unchanged along the length the side photo gives at that height's scale (1.011 in); the bore is cut through at the journal's .625.","The gas tube's hole (its height above the bore, its diameter, how far it runs past the pin) and the roll pin's hole's diameter are the Army's front sight's (drawing 8448566): the block takes the same tube and pin, and the pin's hole in the side photo is at that height and size within the photo's ±. The pin's place along the block is the side photo's; the tube's hole enters from the rear face and the star face is closed, as the photos of the .750 block's rear show for that block.","The gas port is where the standard tube's gas hole lands (.418 behind the pin, drawing 8448567): 0.276 in ahead of the rear face, which the Army's sight has at .270. The port's hole up from the bore isn't drawn (inside).","The star on the front face is a regular five-pointed star, one point up, at the size and height its five tips give in the turned picture, standing 0.002 in proud of the face so that it shows.","Not drawn: the two set screws and their threaded holes in the tab (BCM: 10-32 x 3/16 knurled cup point; no view of the underside is on file, so where they sit along the block isn't sourced). The bore's wall is the body's own faces in a slot of their own (`bore`: honed after the finish, bare steel). Edges broken at 0.006 in (the photos show a small break; its size isn't measured)."],"ledger":["bcm-625-gas-block.journal_id","bcm-625-gas-block.length","bcm-625-gas-block.height","bcm-625-gas-block.height_above_bore","bcm-625-gas-block.tab_below_bore","bcm-625-gas-block.od","bcm-625-gas-block.boss_width","bcm-625-gas-block.port_from_rear","bcm-625-gas-block.pin_hole_from_front","bcm-625-gas-block.pin_hole_d","bcm-625-gas-block.tube_hole_above_bore","bcm-625-gas-block.tube_hole_d","bcm-625-gas-block.tube_hole_past_pin","bcm-625-gas-block.star_center_above_bore","bcm-625-gas-block.star_radius"]},"profiles":{"front":{"plane":"zy","origin":"the bore's axis","offset":{},"points":[[-0.427,0.03],[-0.417,-0.09],[-0.383,-0.193],[-0.361,-0.237],[-0.148,-0.552],[0.147,-0.552],[0.371,-0.218],[0.408,-0.127],[0.427,-0.019],[0.418,0.101],[0.397,0.176],[0.376,0.22],[0.331,0.291],[0.169,0.475],[0.141,0.548],[0.126,0.663],[0.099,0.73],[0.073,0.76],[0.051,0.774],[0.002,0.789],[-0.045,0.778],[-0.073,0.76],[-0.099,0.73],[-0.126,0.663],[-0.132,0.585],[-0.161,0.492],[-0.196,0.44],[-0.304,0.322],[-0.359,0.248],[-0.398,0.172],[-0.418,0.101]],"scaleRefs":["bcm-625-gas-block.height_above_bore","bcm-625-gas-block.tab_below_bore"],"inputs":{"bcm-625-gas-block.height_above_bore":0.789,"bcm-625-gas-block.tab_below_bore":0.551},"tolerance":0.004,"photo":"references/bcm-625-gas-block 694b5d90ca1f (Primary Arms BCM-LGB-625_00.jpg (453104958d81), the star face turned square by the block's own bore (the mouth round, the face's axis upright): derived-694b5d90ca1f.manifest.json, 1200 x 1600)","method":"manual polygon (77 points picked on the photo); frame from the reviewed holes top, flat (800.0 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.004 in with the extremes kept: 31 points (IoU 0.994 with the full outline); the frame is two points on the face's own axis: the boss's top and the tab's flat, at their heights from the bore's centre (the mouth's, at (600, 920)); the bore's mouth then reads 0.630 in across, 0.75% over the .625 it is honed to (its edge break); the outline's left side is the face's edge at grey 150 on rows 390 to 1350, its top four points inside the silhouette, its right side the left's mirror about the axis (tools/trace.py)","via":"harvest","note":"Its outline end-on, from an oblique photo turned square by its own bore: the ring about the barrel, the tube's boss on top, the set screws' tab underneath. Symmetric by construction (its right side is its left's mirror). The bore is open: a section with a hole is drawn solid and the barrel fills it."}},"gaps":[{"what":"A straight end view, for the section's widths","need":"A photo of the block end-on with its bore seen through (every one on file is a three-quarter view), or a maker's drawing: it would say whether the .625 block's ring is the .750's 0.88 in or the 0.85 its own photo reads"},{"what":"Its weight","need":"BCM publishes none and no seller's page read states one (MidwayUSA's 0.183 lb is the parcel's; a second parts-database page said to carry 2.8 oz wasn't read): it is worked out from its steel, 1.93 oz ± 0.12. A scale would settle it"},{"what":"Its height and length from its maker","need":"BCM's own figures: the 1.34 in is a parts database's for this number, unsourced, borne out by the block's own bore in its photo (1.33) and by the .750 block's two sellers"},{"what":"The set screws' places along the tab and their holes, and the rear face","need":"A photo of the underside and one of the rear of this block (its oblique photo shows the front screw's hole in the bore's floor, its middle about 0.3 in behind the star face and about 0.2 across; the one rear view on its sellers' pages is BCM's picture of the .750 block)"}]},"bcm-750-gas-block":{"id":"bcm-750-gas-block","name":"Low Profile Gas Block (steel with set screws) 750","manufacturer":"BCM","sku":"BCM-LGB-750","url":"https://bravocompanyusa.com/bcm-low-profile-gas-block-steel-with-set-screws-750/","category":"gas_block","description":"Bravo Company's low-profile gas block for a .750 in journal: steel, phosphate finish, its bore honed after finishing, held by two 10-32 x 3/16 knurled cup point set screws. The gas tube's roll pin isn't included.","weight":"bcm-750-gas-block.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"journal":{"origin":[0,0,0],"note":"On the bore axis at the gas port, +x toward the muzzle. The port is where the standard tube's gas hole lands with its pin in the block's cross hole: 0.275 in ahead of the rear face (port_from_rear)."},"gas_tube":{"origin":[0,"{.tube_hole_above_bore}",0],"x":[-1,0,0],"note":"The tube's hole at the port, +x rearward toward the receiver: the Army's height for the tube at the block (.625 above the bore), which the roll pin's hole in the side photo agrees with."}},"interfaces":{"gas_journal":{"type":"ar15.gas_journal","role":"block","anchor":"journal","params":{"journal_od":"={.journal_id}"},"flips":false,"note":"BCM: \"Machined of steel, phosphate finish, for .750 barrels.\" and \"Barrel ID honed after finish per USGI TDP.\" Mounted by set screws (BCM's component page: \"Mounted via steel set screws with texturing on the base to prevent back out\"); Primary Arms: \"This gas block does not include a gas tube roll pin\"."},"gas_tube":{"type":"ar15.gas_tube","role":"block","anchor":"gas_tube","params":{},"flips":false}},"materials":{"body":{"label":"Gas block","finish":"phosphate","recolorable":false,"color":"steel-phosphate-black","note":"BCM: \"Machined of steel, phosphate finish\" (its component page: \"STEEL CONSTRUCTION - PHOSPHATE FINISH\"); Alexander's: \"Black Phosphate\". AR15Discounts' table says \"Finish Black Nitride\" against its own description (\"Machined from steel then phosphate finished\"): the maker's phosphate is taken. One finish. A blacker phosphate than BCM's barrel in the same seller's photos (#222320 and #2c2c2b on Primary Arms' two views of the block, #3a3a38 on its barrel): matched on them (data/colors/steel.yaml). The two set screws (\"Steel 10-32 x 3/16 Knurled Cup Point\") aren't drawn."},"bore":{"label":"Bore","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"BCM: \"Barrel ID honed after finish per USGI TDP.\" (its component page: \"bore internal dimensions honed after finish\"): the bore's wall is bare steel, bright against the black phosphate in every photo of the block (Primary Arms' 3ce1f7e276b9 and ec4b889d2aba, BCM's own). On a barrel it is out of sight; it shows in the exploded view. Bright metal isn't fitted to a photo: the app's natural stainless. The faces of the body's mesh that lie on the bore."},"marking":{"label":"Star","finish":"steel","recolorable":false,"color":"stainless-natural","note":"BCM's star, laser-marked light grey on the front face (Primary Arms' three-quarter view, 3ce1f7e276b9; BCM's own gallery). A mark, drawn because it is the block's one feature from the front: the app's natural-steel grey, not matched to a photo."}},"components":{},"geometry":{"model":"bcm-750-gas-block.glb","components":{},"approximations":["Its section is read off an oblique photo of the star face turned square (its axis upright, the tab's flat level, widths set against heights so that the bore's mouth is as wide as it is tall) and scaled by two sellers' height (1.34 in): no straight end view is on file. Three gauges of its widths agree within 2% (the mouth's two chords, the star's proportions, the block's own edges); the outline's two sides differ by up to 0.02 in and the model's section is their mean about the bore's centre. Widths are good to about 0.025 in.","The section is run unchanged along the length the side photo gives at that height's scale (1.008 in; the sellers say 1 inch); the bore is cut through at the journal's .750.","The gas tube's hole (its height above the bore, its diameter, how far it runs past the pin) and the roll pin's hole's diameter are the Army's front sight's (drawing 8448566): the block takes the same tube and pin, and the pin's hole in the side photo is at that height and size within the photo's ±. The pin's place along the block is the side photo's; the tube's hole enters from the rear face and the star face is closed, as BCM's photos show.","The gas port is where the standard tube's gas hole lands (.418 behind the pin, drawing 8448567): 0.275 in ahead of the rear face, which the Army's sight has at .270. The port's hole up from the bore isn't drawn (inside).","The star on the front face is a regular five-pointed star, one point up, at the size and height its five tips give in the rectified photo, standing 0.002 in proud of the face so that it shows.","Not drawn: the two set screws and their threaded holes in the tab (BCM: 10-32 x 3/16 knurled cup point; no view of the underside is on file, so where they sit along the block isn't sourced). The bore's wall is the body's own faces in a slot of their own (`bore`: honed after the finish, bare steel). Edges broken at 0.006 in (the photos show a small break; its size isn't measured)."],"ledger":["bcm-750-gas-block.journal_id","bcm-750-gas-block.length","bcm-750-gas-block.height","bcm-750-gas-block.height_above_bore","bcm-750-gas-block.tab_below_bore","bcm-750-gas-block.od","bcm-750-gas-block.boss_width","bcm-750-gas-block.port_from_rear","bcm-750-gas-block.pin_hole_from_front","bcm-750-gas-block.pin_hole_d","bcm-750-gas-block.tube_hole_above_bore","bcm-750-gas-block.tube_hole_d","bcm-750-gas-block.tube_hole_past_pin","bcm-750-gas-block.star_center_above_bore","bcm-750-gas-block.star_radius"]},"profiles":{"front":{"plane":"zy","origin":"the bore's axis","offset":{},"points":[[-0.432,-0.022],[-0.418,-0.13],[-0.39,-0.203],[-0.363,-0.252],[-0.147,-0.556],[0.15,-0.556],[0.396,-0.221],[0.433,-0.115],[0.448,0.03],[0.447,0.11],[0.434,0.171],[0.394,0.235],[0.344,0.298],[0.276,0.355],[0.221,0.416],[0.2,0.444],[0.167,0.515],[0.155,0.585],[0.154,0.689],[0.144,0.725],[0.123,0.752],[0.09,0.774],[0.065,0.786],[0.038,0.79],[-0.03,0.776],[-0.065,0.759],[-0.092,0.73],[-0.12,0.675],[-0.135,0.563],[-0.159,0.476],[-0.205,0.397],[-0.291,0.309],[-0.329,0.264],[-0.356,0.219],[-0.404,0.117],[-0.428,0.019]],"scaleRefs":["bcm-750-gas-block.height_above_bore","bcm-750-gas-block.tab_below_bore"],"inputs":{"bcm-750-gas-block.height_above_bore":0.785,"bcm-750-gas-block.tab_below_bore":0.555},"tolerance":0.004,"photo":"references/bcm-750-gas-block 04a45a69497d (Primary Arms BCM-LGB-750_00.jpg (3ce1f7e276b9), the star face turned square (its axis upright, its flat level, the bore's mouth as wide as tall): derived-04a45a69497d.manifest.json, 1200 x 1600)","method":"manual polygon (57 points picked on the photo); frame from the reviewed holes top, flat (795.7 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.004 in with the extremes kept: 36 points (IoU 0.994 with the full outline); the frame is two points on the face's own axis: the boss's top and the tab's flat, at their heights from the bore's centre (the mouth's, at (600, 920)); the bore's mouth then reads 0.770 in across along the axis, 2.6% over the .750 it is honed to (its edge break); the outline was picked on the first rectification (2a13962b1e9e) and carried here point by point (tools/trace.py)","via":"harvest","note":"Its outline end-on, from an oblique photo turned square: the ring about the barrel, the tube's boss on top, the set screws' tab underneath. Its two sides differ by up to 0.02 in; a model takes their mean. The bore is open: a section with a hole is drawn solid and the barrel fills it."}},"gaps":[{"what":"A straight end view, for the section's widths","need":"A photo of the block end-on with its bore seen through (BCM's own are three-quarter views), or a maker's drawing"},{"what":"The block's length as the oblique photo shows it","need":"With the star face turned square, the block's long edges under a camera without perspective make it 0.89 in long against the side photo's 1.008 (the photo's perspective shortens them: the far face is about 5% smaller than the near one). By the mouth's fitted ellipse taken whole it read 1.3 to 1.45 in: the edge finder runs inside the rim along the ellipse's long axis, so that reading was dropped. A camera fitted to both oblique views (3ce1f7e276b9, ec4b889d2aba) with the mouth's rim picked by hand would close it; the side photo's length is the one used"},{"what":"The set screws' places along the tab and their holes","need":"A photo of the underside (the two oblique photos show the front screw's hole in the bore's floor about a quarter of the length behind the star face)"},{"what":"Its weight from its maker","need":"BCM publishes none; AR15Discounts' 2.08 oz is the only figure, and the model's volume in steel is about 1.4 oz (Aero's block of the same size weighs 1.6 by its maker): either the ring is thicker than the oblique photo shows or the seller's figure is a shipping weight"}]},"bcm-bcg":{"id":"bcm-bcg","name":"Bolt Carrier Group (MPI) - Auto","manufacturer":"BCM","sku":"BCM-BCG-AUTO","url":"https://bravocompanyusa.com/bcm-bolt-carrier-group-mpi-auto/","category":"bolt_carrier_group","description":"Bravo Company's complete bolt carrier group: an M16 (\"auto\") carrier, Parkerized outside and chrome lined inside, with a Carpenter No. 158 bolt, high pressure tested and magnetic particle inspected.","weight":"bcm-bcg.weight","cartridge":{"takes":["5.56 NATO",".223 Rem"],"stated":"Chambered in 5.56 NATO (the seller Primary Arms); Caliber: 223 Remington (the seller Aerospace Arms)","source":"Two sellers' words, not BCM's: https://www.primaryarms.com/bravo-company-manufacturing-bolt-carrier-group-bcm-bcg (a feature bullet; its table has \"Caliber Gauge 5.56 NATO\") and https://aerospacearms.com/bravo-company-m16-bolt-carrier-group/ (its \"Features and Specifications\", under the maker's number BCM-BCG-AUTO), as cached: harvest.quote. BCM's own page names no cartridge: \"Bolt carrier group (auto version) for your AR15, M16, or M4.\""},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"channel":{"origin":[0,0,0],"note":"The receiver's rear face on the bore axis, +x toward the muzzle: the carrier's rear face stands here in battery."}},"interfaces":{"carrier_channel":{"type":"ar15.carrier_channel","role":"carrier","anchor":"channel","params":{},"flips":false}},"materials":{"body":{"label":"Carrier group","finish":"phosphate","recolorable":false,"color":"steel-phosphate-dark","sheen":"satin","note":"BCM: \"Parkerized exterior and chrome lined inside carrier.\" Primary Arms' table for it: \"Carrier Finish Manganese Phosphate\", \"Bolt Finish Manganese Phosphate\"; Aerospace Arms: \"Color: Black Finish: Parkerized (Matte)\". The one finish it is sold in (BCM's flat dark earth carrier is another product). The carrier, the key, the cam pin and the bolt are one slot: piece by piece on BCM's five photos and Primary Arms' five they are all that phosphate, and which of them reads lighter changes with the photo (the key against the tail: #40403b against #323230 in Primary Arms' side view, #2f3034 against #414143 in BCM's). Satin, for the oil it is photographed in (BCM's carrier page: \"the carrier still needs a thin coat of oil on it at all times\"). Not drawn: the chrome inside the key's mouth and the carrier (the mouth is bright in Primary Arms' three-quarter view), \"BCM\" lasered light grey on the right side, the extractor."},"screws":{"label":"Key screws","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The key's two socket screws: a blacker, smoother black than the phosphated key in Primary Arms' three-quarter view (1f36500d87ec) and in BCM's view from above (0eea516be4aa), where the staking beside them shows grey. No page names their finish: a black, not matched to a photo (two heads a quarter inch across)."}},"components":{},"geometry":{"model":"bcm-bcg.glb","components":{},"approximations":["Its shape is the Army's drawings', not BCM's own (no drawing or dimension of BCM's is published): BCM says \"Bolt carrier group (auto version) for your AR15, M16, or M4 ... Machined to USGI specifications. This M16/M4 carrier includes the proper Mil-Spec gas key\", so it is drawn as the M16 carrier (8448507), its key (8448506) and screws (8448508), the cam pin (8448502) and the bolt (8448510) at those drawings' nominal sizes. BCM's photos of it show that carrier; nothing was measured from them.","Drawn as the Army's assembly drawing (8448501) has it and as BCM photographs it, out of the rifle: the bolt forward in the carrier (unlocked) and the cam pin upright. In battery the bolt is turned 22 1/2° and stands .255 to .325 in further back in the carrier; the carrier's rear face is put at the receiver's rear face.","Not drawn: the bores inside the carrier ahead of the slot and the bolt behind the carrier's front face, the extractor (its claw stands in as an eighth lug) and the ejector, the firing pin and its retaining pin, the gas rings, the key's 22°30' relief and its staking, BCM's marking, fillets and edge breaks beyond the two cut corners and a small bevel.","Assumed where the drawing wasn't resolved: each lower rail's lower flank is the plane through the axis that touches the groove beside it (the end view's 10° callout wasn't placed); the groove's centre is where it touches the rib's side on the 45° ray; the cam track's helix is straight between the table's 0° and 20° rows; the 1.500 R is the run-out of the two grooves to the rear, from 2.35 ahead of the tail's shoulder (first read as the bottom cut's own); the notch under the tail runs the tail's length; the serrations' steep faces are toward the front, as the makers' photos show them; the screws' heads are flush with the key's top (the counterbores' depth isn't dimensioned); the vents, the hole in the right side and the cam track are drawn in as far as the bolt's diameter."],"ledger":["bcm-bcg.length","bcm-bcg.od"]},"profiles":{},"gaps":[{"what":"A weight of BCM's own","need":"BCM publishes none (its page's weight field is empty): the figure is the seller Primary Arms', beside a magazine's scale reading of a BCM group it doesn't name"},{"what":"The cartridge in BCM's words","need":"BCM's page names none; two sellers do, differently (5.56 NATO, 223 Remington)"},{"what":"Anything of BCM's own shape (its marking)","need":"A straight, scaled side photo, or BCM's drawing: the model is the Army's carrier"}]},"bcm-carbine-action-spring":{"id":"bcm-carbine-action-spring","name":"Carbine Action Spring","manufacturer":"BCM","sku":"SPRING-CARBINE-ACTION","url":"https://bravocompanyusa.com/carbine-action-spring/","category":"buffer_spring","description":"The spring inside the receiver extension, round the buffer, that sends the bolt carrier forward again after each shot. BCM: \"Action spring for AR15, M4 adjustable stocks.\" \"Made to M4A1 Mil-Spec specifications.\"","weight":"bcm-carbine-action-spring.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"bore":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the receiver extension's axis where a buffer's front face rests, +x rearward."}},"interfaces":{"bore":{"type":"ar15.extension_bore","role":"buffer","anchor":"bore","params":{},"flips":false}},"materials":{"spring":{"label":"Spring","finish":"steel","recolorable":false,"color":"bcm-spring-wire","note":"A bronze-brown wire in BCM's photo (f579fe1120ef). The Army's drawing of the rifle's action spring has stainless wire, type 631 (17-7 PH), heat treated, which takes that colour; BCM states only \"Made to M4A1 Mil-Spec specifications\"."}},"components":{},"geometry":{"model":"bcm-carbine-action-spring.glb","components":{},"approximations":["Drawn as it is in a rifle: held between a carbine buffer's head and the rear wall inside a mil-spec carbine receiver extension, 7.0 in long, where it is 10.7 in free. Its wire (.072 in) and outside diameter (.940) are the Army's drawing's of the rifle's action spring, since BCM says of this one only that it is made to the M4A1's specifications; its 38 and a half coils are counted on BCM's photo of it.","Its end coils are closed; the one coil at each end that the Army's drawing reduces to .900 isn't."],"ledger":["bcm-carbine-action-spring.wire_d","bcm-carbine-action-spring.od","bcm-carbine-action-spring.coils","bcm-carbine-action-spring.free_length","bcm-carbine-action-spring.installed_length"]},"profiles":{},"gaps":[{"what":"Its weight","need":"BCM's figure or a scale: 1.95 oz is worked out from its wire's length and steel's density"},{"what":"Its free length, wire and diameter as BCM makes it","need":"BCM's figures: they are the standard's and the Army's drawing's of the rifle's spring"}]},"bcm-carbine-buffer":{"id":"bcm-carbine-buffer","name":"Carbine Buffer","manufacturer":"BCM","sku":"Buffer-Carbine","url":"https://bravocompanyusa.com/carbine-buffer/","category":"buffer","description":"The standard-weight carbine buffer, the weight inside the receiver extension that the bolt carrier pushes back against. BCM: \"Standard Carbine Buffer for your carbine, AR15, M4.\" \"Weighted with 3 steel weights 3.0oz.\" The buffer BCM's stock hardware kit comes with unless a heavier one is chosen.","weight":"bcm-carbine-buffer.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"bore":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the buffer's axis at its head's front face, +x rearward."}},"interfaces":{"bore":{"type":"ar15.extension_bore","role":"buffer","anchor":"bore","params":{},"flips":false}},"materials":{"body":{"label":"Buffer body","finish":"anodized_matte","recolorable":false,"color":"bcm-buffer-anodize","note":"Aluminium, a tan anodize in BCM's photo of it (c75e44c92794): the Army's drawing of the rifle buffer's body has it hard coat anodized and sealed, undyed (MIL-A-8625, Type III, Class 1), which comes out this colour. BCM states neither material nor finish."},"bumper":{"label":"Bumper","finish":"polymer","recolorable":false,"color":"bcm-buffer-bumper","note":"The Army's drawing (8448619, the bumper the M4's buffer shares): \"RUBBER, POLYETHER URETHANE, CASTABLE, SHORE A DUROMETER 95±3\". Cream in BCM's photo of the carbine buffer; a pale green on the H buffer in Primary Arms'."},"pin":{"label":"Pin","finish":"steel","recolorable":false,"color":"steel-phosphate-dark","note":"The spring pin through the body and the bumper (8448521-1 on the Army's assembly drawing): a dark dot in a hole in BCM's side photo."}},"components":{},"geometry":{"model":"bcm-carbine-buffer.glb","components":{},"approximations":["The standard carbine buffer's shape (the Army's drawings of the rifle buffer's head, bumper and pin, which the M4's shares, and the carbine body of the reference CAD set, a third-party model of a mil-spec rifle): BCM states no size for its own, and its side photo has these proportions. A thick head with three flats, a step behind it that the spring's end sits over, the body, the bumper standing 0.4 in out of it, the pin across both.","Not drawn: the three steel weights and the discs between them inside it (BCM: \"Weighted with 3 steel weights\"), which is what the heavier buffers change; the dimple in the middle of its face; any mark on it.","In a build its face rests where the bolt carrier's rear end stands with the bolt forward, at the upper receiver's rear face (the Army's drawings): 0.05 in ahead of the receiver extension's mouth as the ledger places the extension, 0.02 in the reference model."],"ledger":["bcm-carbine-buffer.length","bcm-carbine-buffer.od","std.carbine_buffer.head_thickness","std.carbine_buffer.body_d","std.carbine_buffer.bumper_exposed"]},"profiles":{},"gaps":[{"what":"Its own sizes","need":"BCM's figures or a photo with scale: its length, head and body are the standard pattern's"}]},"bcm-castle-nut":{"id":"bcm-castle-nut","name":"Receiver Extension Nut (Castle Nut)","manufacturer":"BCM","sku":"CASTLE-NUT-AR15","url":"https://bravocompanyusa.com/receiver-extension-nut-castle-nut/","category":"castle_nut","description":"The nut on the receiver extension's thread that is turned down onto the end plate and locks the extension to the lower receiver; its notches take the wrench. BCM: \"To secure lock plate on an adjustable stock for AR15, M4\".","weight":"bcm-castle-nut.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"seat":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the tube axis at the nut's front face, which bears on the end plate, +x rearward."}},"interfaces":{"nut_seat":{"type":"ar15.end_plate_seat","role":"nut","anchor":"seat","params":{},"flips":false}},"materials":{"nut":{"label":"Castle nut","finish":"phosphate","recolorable":false,"color":"steel-phosphate-charcoal","note":"Steel; BCM states no finish for it. Its own photo of the nut (bravocompanyusa.com/receiver-extension-nut-castle-nut/) shows a matte, grainy dark grey (#434340 on its lit face), as a manganese phosphate is, against the tube's satin black: phosphate by its look, not by a sentence."}},"components":{},"geometry":{"model":"bcm-castle-nut.glb","components":{},"approximations":[],"ledger":["bcm-castle-nut.od","bcm-castle-nut.thickness","bcm-castle-nut.notches","bcm-castle-nut.notch_width","bcm-castle-nut.notch_depth","bcm-castle-nut.rear_face_behind_pin"]},"profiles":{},"gaps":[]},"bcm-delta-ring-assembly":{"id":"bcm-delta-ring-assembly","name":"Delta Ring Assembly - AR15","manufacturer":"BCM","sku":"DELTA-RING-ASSEMBLY-AR15","url":"https://bravocompanyusa.com/delta-ring-assembly-ar15/","category":"delta_ring","description":"The spring-loaded ring on the barrel nut that holds the rear of a drop-in handguard, with the wave spring that pushes it forward and the snap ring that keeps both on the nut. Pulled back toward the receiver, it lets the handguard's halves out. BCM: \"Delta Ring Assembly for your AR15, M16, M4. This assembly includes 3 parts: Delta Ring, Weld Spring, and Snap Ring\".","weight":"bcm-delta-ring-assembly.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"seat":{"origin":[0,0,0],"note":"Part frame: the receiver's front face on the bore axis, +x toward the muzzle."}},"interfaces":{"delta_ring":{"type":"ar15.delta_ring","role":"ring","anchor":"seat","params":{},"flips":false,"note":"On a barrel nut: its snap ring in the nut's groove, its lip on the nut's body (the Army's assembly, 8448711)."},"drop_in":{"type":"ar15.drop_in","role":"ring","params":{},"flips":false}},"materials":{"ring":{"label":"Delta ring","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","note":"BCM states no material or finish. The Army's drawing (8448712): \"ALUMINUM ALLOY 7075-T6\", its outside grit-blasted to \"a non reflective matte surface\", anodized to MIL-A-8625 Type 3 Class 2, \"lusterless (flat)\" black; BCM's photo (96d01c941da6) shows it a flat, dark grey-black, darker than the steel pieces beside it: a matte black anodize. Drawn in the catalog's black, as BCM's black anodize is (data/colors/bcm.yaml: \"a black isn't fitted\"): fitted to BCM's photo of the loose parts on white (its outside reads #544f4c), the ring rendered a warm grey (albedo #5d5652) beside the receivers' black in the hero view, which is the photo's exposure of a black, not the ring's colour. One look."},"spring":{"label":"Weld spring and snap ring","finish":"phosphate","recolorable":false,"color":"steel-phosphate-charcoal","note":"Steel. BCM states no finish; the Army's drawing of the weld spring (8448555, note 1) a phosphate by MIL-STD-171 (5.3.1.2 or 5.3.2.2: manganese or zinc). BCM's photo shows the spring and the snap ring a dry, mottled mid grey with rub marks, lighter than the ring, as a phosphate is: phosphate by its look and the drawing, in the catalog's charcoal phosphate. Not fitted to that photo: the spring's sides read #575755 and the snap ring's flat, lit from above, #84827f, two surfaces in two lights, and in the app's views the spring is inside the ring and the snap ring a sliver behind it. One look."}},"components":{},"geometry":{"model":"bcm-delta-ring-assembly.glb","components":{},"approximations":["Every size is the Army's drawings' (8448712 the ring, 8448555 and 8448556 the weld spring) or, for the snap ring (MS16626-3137, not in the package), the reference CAD set's: BCM states none, and its one photo, an oblique of the three laid out, is counted (the ring's seven lands) and not measured.","The ring stands forward on its spring, its lip against the nut's flange, as the Army's assembly draws it (std.ar15.slip_ring_front_x). A drop-in handguard presses it back by as much as the handguard's length asks, which isn't drawn.","The weld spring: four sections of the drawing's .020 strip, 1.410 to 1.730 across, three waves round (the section's drawing bends it every 60 degrees, crests and troughs in turn), each section in the opposite phase to the next so that they touch crest to trough (the drawing's diamonds, welded there), pressed to the height the ring's lip leaves it above the snap ring (0.50 of its free .552); the bends are drawn as a smooth wave, not the drawing's 10 degree flats.","Its gaps (the spring's, the snap ring's), and the notch in the ring's lip, are at the top, where the gas tube passes, as Spike's photo of the same parts assembled has them (references/spikes-tactical-sdr100a 009abbbe250f).","The snap ring is drawn seated: as wide as the nut's groove (the reference model's is 0.050 thick, the groove 0.045) and its inside on the groove's floor (the model's is drawn free, 1.372 across inside); a flat ring, its gap's faces square, a hole in each end, and its inside the reference model's: the 1.372 circle at its ends' lugs (to 42 degrees from the gap) and over its back (from 127.6), cut away between them to 1.503 across at 73.4 degrees (the photos show the ends wider than the ring beside them); the model's two arcs there are drawn as a half cosine each side of the waist, and the whole inside comes down by the 0.0195 the ring is sprung into the groove.","Not drawn: the 0.010 rounds inside the ring's lip."],"ledger":["bcm-delta-ring-assembly.outside_diameter","bcm-delta-ring-assembly.length","bcm-delta-ring-assembly.lands"]},"profiles":{},"gaps":[{"what":"BCM's own figures","need":"Any size, weight or finish BCM states for these parts: every figure here is the Army's drawings' or the reference model's"}]},"bcm-end-plate":{"id":"bcm-end-plate","name":"Receiver End Plate","manufacturer":"BCM","sku":"RECEIVER-END-PLATE","url":"https://bravocompanyusa.com/receiver-end-plate/","category":"end_plate","description":"The plate between the castle nut and the lower receiver: a ring round the receiver extension with a tab that covers the takedown pin's detent spring. BCM: \"Receiver end plate for an adjustable stock for AR15, M4\".","weight":"bcm-end-plate.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"end":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the tube axis at the plate's front face, against the receiver's rear face, +x rearward."},"nut_seat":{"origin":["{.thickness}",0,0],"x":[1,0,0],"note":"The plate's rear face, where the castle nut bears."}},"interfaces":{"extension_end":{"type":"ar15.extension_end","role":"fitting","anchor":"end","params":{},"flips":false},"nut_seat":{"type":"ar15.end_plate_seat","role":"plate","anchor":"nut_seat","params":{},"flips":false}},"materials":{"plate":{"label":"End plate","finish":"phosphate","recolorable":false,"color":"steel-phosphate-charcoal","note":"BCM states neither material nor finish for this plate (\"Machined from steel, and easily accommodates staking\" is its QD end plate's page, which the catalog had taken for this one's until 2026-10-12). Dark and matte beside the tube in BCM's photo of the kit laid out, as the nut is: drawn as the nut."}},"components":{},"geometry":{"model":"bcm-end-plate.glb","components":{},"approximations":[],"ledger":["bcm-end-plate.thickness","bcm-end-plate.height","bcm-end-plate.top_above_axis","bcm-end-plate.bottom_below_axis"]},"profiles":{"face":{"plane":"zy","origin":"the plate's top edge, centred on the ring; offset up to its height above the tube axis","offset":{"y":"top_above_axis"},"points":[[-0.661,-0.71],[-0.64,-0.829],[-0.556,-1.024],[-0.42,-1.669],[-0.379,-1.784],[-0.304,-1.884],[-0.202,-1.961],[-0.108,-1.996],[0.017,-2.006],[0.115,-1.985],[0.216,-1.936],[0.319,-1.837],[0.368,-1.75],[0.549,-1.034],[0.637,-0.839],[0.661,-0.64],[0.651,-0.536],[0.602,-0.389],[0.522,-0.256],[0.447,-0.174],[0.356,-0.105],[0.248,-0.049],[0.115,-0.01],[0,-0.003],[-0.007,0],[-0.154,-0.017],[-0.258,-0.052],[-0.387,-0.126],[-0.476,-0.201],[-0.56,-0.309],[-0.616,-0.417],[-0.651,-0.532]],"scaleRefs":["bcm-end-plate.height"],"inputs":{"bcm-end-plate.height":2.006},"tolerance":0.01,"photo":"references/bcm-stock-kit 83b50e3b0f38 (BCM receiver end plate, straight face-on, 623 x 800)","method":"luminance < 150, closing ×2, largest piece, holes filled; scale from bcm-end-plate.height = 2.006 in (y-extent 575 px → 286.6 px/in); origin at x center, y max of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 32 points (IoU 0.994 with the full outline) (tools/trace.py)","via":"harvest","note":"Its ring's hole (the tube passes through it) and the detent boss are inside the outline, filled; the ring and the lobe are what show around the tube."}},"gaps":[]},"bcm-front-sight-base-f-750":{"id":"bcm-front-sight-base-f-750","name":"Front Sight Base F - FSB (ID .750) - Milspec for Flat Top Uppers","manufacturer":"BCM","sku":"Front-Sight-Base-F-750","url":"https://bravocompanyusa.com/front-sight-base-f-fsb-id-750-milspec-for-flat-top-uppers/","category":"gas_block","description":"Bravo Company's forged, F-marked A2 front sight base for a .750 journal: the taller base a flat-top upper's rear sight needs (BCM: \"Mil-Spec for rifles issued to the troops require taller front sight bases on all flat top AR rifles.\"). Sold as the base alone, not yet drilled for its taper pins: \"Not included are front sight post assembly, sling swivel assembly, and taper pins.\" Drawn as installed, with its two taper pins (BCM sells them as a set of two, TAPER-PINS-FSB-SET-2) and without a swivel; its post is a part of its own.","weight":"bcm-front-sight-base-f-750.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"journal":{"origin":[0,0,0],"note":"On the bore axis at the gas port, +x toward the muzzle: the port is .270 ahead of the rear face (port_from_rear, the Army's drawing 8448566), where the standard tube's gas hole lands with its pin in the base's cross hole (.688 from the rear face: .418 apart, as the tube's drawing has them)."},"gas_tube":{"origin":[0,"{.tube_hole_above_bore}",0],"x":[-1,0,0],"note":"The tube's hole, +x rearward toward the receiver: .625 above the bore (8448566)."},"handguard_cap":{"origin":["-{.port_from_rear}",0,0],"note":"On the bore axis at the rear face, +x toward the muzzle: where a drop-in handguard's cap bears (ar15.handguard_cap). The rear face is flat across the rings and the rear leg (8448566's side view; the CAD set's plane z -1.804)."},"front_sight_post":{"origin":["{.post_from_rear} - {.port_from_rear}","{.post_seat_above_bore}",0],"note":"On the post's axis (1.450 ahead of the rear face, 8448566) at the top of the tower: the floor between the wings the post rises from, the A2's 2.285 above the bore and the F's .040 more (post_seat_above_bore). +y up, +x toward the muzzle."}},"interfaces":{"gas_journal":{"type":"ar15.gas_journal","role":"block","anchor":"journal","params":{"journal_od":"={.journal_id}"},"flips":false,"note":"BCM: \"Front Sight Base F - FSB (ID .750)\", \"(.750\")\". It is pinned to the barrel by two taper pins through base and barrel (BCM: \"These are new and are not yet drilled for taper pins, and should be installed by a qualified gunsmith.\")."},"gas_tube":{"type":"ar15.gas_tube","role":"block","anchor":"gas_tube","params":{},"flips":false,"note":"The standard tube, held by its roll pin through the base's .078 cross hole (8448565, 8448566); the roll pin isn't BCM's base's."},"handguard_cap":{"type":"ar15.handguard_cap","role":"block","anchor":"handguard_cap","params":{"journal_od":"={.journal_id}"},"flips":false,"note":"Magpul's MOE M-LOK instructions: \"Slide the front flange of the upper Hand Guard piece into the metal Hand Guard cap, located behind the front sight base.\""},"front_sight_post":{"type":"ar15.front_sight_post","role":"base","anchor":"front_sight_post","params":{},"flips":false,"note":"BCM: \"Not included are front sight post assembly, sling swivel assembly, and taper pins.\" The post screws into the tower's 8-36 hole (.164-36, 8448566 and the post's 9349056) and its detent holds it."}},"materials":{"body":{"label":"Front sight base","finish":"phosphate","recolorable":false,"color":"steel-phosphate-black","note":"BCM's page names no finish or material. The Army's base is phosphated (8448566 note 3: \"FINISH, 5.3.1.2 OF MIL-STD-171\", manganese phosphate) and BCM calls it \"Milspec\"; Primary Arms' two photos (e1fa9fe8e586, 8c4643da3842) show a black, grit-blasted forging. A black phosphate, as BCM's own phosphated gas block (steel-phosphate-black): a black on phosphate is its finish type's look, not fitted to a photo."},"bore":{"label":"Bore","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"The rings' bore is bare bright steel in both of Primary Arms' photos (8c4643da3842 shows both rings' bores machined bright): the Army's base is honed after its coating (8448566: \"HONE TO SIZE AFTER PHOSPHATE COATING\"). On a barrel it is out of sight; it shows in the exploded view. The faces of the body's mesh that lie on the bore."},"pins":{"label":"Taper pins","finish":"phosphate","recolorable":false,"color":"steel-phosphate-black","note":"The two taper pins that hold an installed base to its barrel: BCM's Taper Pins for Front Sight Base (Set of 2), TAPER-PINS-FSB-SET-2 (\"BCM®'s USGI Taper Pins to secure the front sight base to the barrel on a M16 Rifle or M4 Carbine\"), a product of its own; their ends show on each side of the rings. The Army's pin (8448575): steel, \"5.3.1.2 OF MIL-STD-171\", the base's phosphate."}},"components":{},"geometry":{"model":"bcm-front-sight-base-f-750.glb","components":{},"approximations":["Its side outline is BCM's base itself, Primary Arms' straight side photo of it, framed by the roll pin's hole and the rear face on the pin's row at the Army's .688 (8448566): the rings' front face then reads 1.816 from the rear face (the CAD set's .750 base: 1.804) and the bayonet lug 0.314 ahead of it (0.325).","Every width across is the CAD reference set's .750 base's (a third-party model of the mil-spec part, D49), as one section of the widest it is at each height: the lugs' and ears' width under the rings, the rings' flat feet and round (r 0.44), the tower's sides leaning in, the wings' arcs and the slot between them. Between the legs it is the gas tube's boss alone above the rings (its sides 0.155 out, its top rounded); where the legs meet the boss and the rings the CAD set's small fillets (0.03 in) aren't drawn.","The tower's top between the wings, where the post stands, is the Army's A2 height (2.285 above the bore, 8448566) and the .040 a flat-top's F base stands taller (Windham Weaponry's two pages); the drawing gives no F base. The wings' tips are where BCM's photo has them (2.615), which is the drawing's floor plus .290: the CAD set's wings stand .218 over its own floor and the drawing's A1 wings scale to about .42, so the wings' height above the floor is the photo's alone.","The gas tube's hole (.1805, .625 up, .905 deep from the rear face), the roll pin's cross hole (.078, .688 from the rear face), the post's counterbore (.375, .227 deep), its threaded hole (drawn plain at the thread's major diameter, .164, .738 deep) and the detent's hole beside it (.171, .203 ahead of the post's axis; its depth, .511, the CAD set's) are the Army's (8448566). The bore is the journal's .750, in its own slot (honed bright after the phosphate).","Drawn as installed: BCM sells it undrilled for its taper pins, and a pinned base has two. The two pins are the Army's (8448575: .845 long, .1419 to .1251, spherical ends), across the rings .347 below the bore, centred across the base so each end stands .047 proud of the ring's flat; the rear one where the CAD set has its hole (.2065 from the rear face), the front one at the front ring's middle (an assumption: no source on file places it).","The swivel's rivet hole is where BCM's photo has it (.223 from the rear face, .653 below the bore; the CAD set's .215 and .69); no swivel is drawn (BCM: not included). Edges broken at the drawing's .010.","Not drawn: the gas port up from the bore (inside, .125 at 30 degrees in the drawing), the forging's marks (\"4 C\" on the boss, the \"F\" on the tower)."],"ledger":["bcm-front-sight-base-f-750.journal_id","bcm-front-sight-base-f-750.length","bcm-front-sight-base-f-750.lug_past_front","bcm-front-sight-base-f-750.height_above_bore","bcm-front-sight-base-f-750.post_seat_above_bore","bcm-front-sight-base-f-750.a2_post_seat_above_bore","bcm-front-sight-base-f-750.f_over_a2","bcm-front-sight-base-f-750.post_from_rear","bcm-front-sight-base-f-750.port_from_rear","bcm-front-sight-base-f-750.pin_hole_from_rear","bcm-front-sight-base-f-750.tube_hole_above_bore","bcm-front-sight-base-f-750.tube_hole_d","bcm-front-sight-base-f-750.tube_hole_depth","bcm-front-sight-base-f-750.ring_r","bcm-front-sight-base-f-750.ring_flat_half","bcm-front-sight-base-f-750.boss_half","bcm-front-sight-base-f-750.tower_foot_half","bcm-front-sight-base-f-750.tower_top_half","bcm-front-sight-base-f-750.slot_half","bcm-front-sight-base-f-750.post_counterbore_d","bcm-front-sight-base-f-750.post_counterbore_depth","bcm-front-sight-base-f-750.detent_hole_d","bcm-front-sight-base-f-750.detent_ahead_of_post","bcm-front-sight-base-f-750.detent_hole_depth","bcm-front-sight-base-f-750.swivel_hole_from_rear","bcm-front-sight-base-f-750.swivel_hole_below_bore","bcm-front-sight-base-f-750.taper_pin_from_rear","bcm-front-sight-base-f-750.front_taper_pin_from_front","bcm-front-sight-base-f-750.taper_pin_length"]},"profiles":{"side":{"plane":"xy","origin":"the gas port on the bore's axis","offset":{},"points":[[-0.27,0.914],[-0.27,-0.125],[-0.266,-0.419],[-0.239,-0.49],[-0.219,-0.51],[-0.211,-0.529],[-0.208,-0.682],[-0.192,-0.747],[-0.158,-0.793],[-0.1,-0.828],[-0.065,-0.836],[-0.027,-0.836],[0.028,-0.823],[0.077,-0.793],[0.106,-0.761],[0.125,-0.728],[0.136,-0.687],[0.139,-0.63],[0.136,-0.488],[0.15,-0.474],[0.144,-0.452],[0.185,-0.395],[0.199,-0.365],[0.185,0.368],[0.188,0.415],[0.202,0.456],[0.23,0.474],[0.843,0.471],[0.884,0.479],[0.974,0.479],[1.004,0.471],[1.028,0.45],[1.06,0.365],[1.066,-0.187],[1.058,-0.351],[1.066,-0.378],[1.081,-0.396],[1.149,-0.421],[1.175,-0.455],[1.181,-0.829],[1.186,-0.857],[1.192,-0.87],[1.204,-0.877],[1.447,-0.877],[1.465,-0.87],[1.46,-0.775],[1.469,-0.752],[1.805,-0.743],[1.856,-0.693],[1.856,-0.54],[1.853,-0.444],[1.844,-0.434],[1.734,-0.391],[1.611,-0.33],[1.557,-0.325],[1.542,-0.302],[1.528,-0.231],[1.503,0.108],[1.52,0.338],[1.542,0.396],[1.531,0.792],[1.533,0.877],[1.528,0.934],[1.531,1.019],[1.525,1.046],[1.514,2.288],[1.501,2.307],[1.487,2.375],[1.457,2.444],[1.387,2.527],[1.335,2.565],[1.28,2.593],[1.207,2.612],[1.136,2.615],[1.029,2.59],[0.963,2.552],[0.913,2.507],[0.776,2.321],[0.747,2.292],[0.731,2.286],[0.702,2.255],[0.56,2.055],[0.336,1.763],[-0.247,0.978]],"features":{"window":[[[-0.009,0.901],[-0.009,0.932],[0.008,0.97],[0.207,1.235],[0.306,1.347],[0.399,1.489],[0.687,1.871],[0.693,1.868],[0.731,1.887],[0.92,1.89],[0.955,1.885],[1.004,1.863],[1.03,1.834],[1.049,1.787],[1.049,1.547],[1.069,1.489],[1.103,1.45],[1.133,1.431],[1.179,1.414],[1.242,1.403],[1.282,1.369],[1.315,1.309],[1.32,1.262],[1.317,1.107],[1.323,0.948],[1.317,0.904],[1.301,0.863],[1.28,0.84],[1.25,0.821],[1.215,0.81],[1.174,0.807],[0.217,0.796],[0.099,0.799],[0.069,0.807],[0.036,0.826],[0.005,0.863]]]},"scaleRefs":["bcm-front-sight-base-f-750.pin_to_port","bcm-front-sight-base-f-750.tube_hole_above_bore","bcm-front-sight-base-f-750.port_from_rear"],"inputs":{"bcm-front-sight-base-f-750.pin_to_port":0.418,"bcm-front-sight-base-f-750.port_from_rear":0.27,"bcm-front-sight-base-f-750.tube_hole_above_bore":0.625},"tolerance":0.004,"photo":"references/bcm-front-sight-base-f-750 e1fa9fe8e586 (Primary Arms Front-Sight-Base-F-750_01.jpg: BCM's base from its right side, straight on, the muzzle at the right, 2200 x 1467)","method":"luminance < 215, largest piece, holes up to 3000 px filled; frame from the reviewed holes pin, rear (365.7 px/in, rms 0.000 in over 2 points); origin at the photo's frame; clipped to x min 0 - {.port_from_rear} = -0.27; Douglas-Peucker at 0.004 in with the extremes kept: 84 points (IoU 0.996 with the full outline); the roll pin's hole is a circle through its see-through rim's 50% crossings on 180 rays (centre (963.6, 822.1), 24.1 px across: the far rim cuts the .078 hole down), the rear face the outline's left edge on the pin's row (rows 750 to 1100 at column 712 at the 150 level); the two at the drawing's .688 (8448566) give 365.7 px/in and the photo's own level; checks: x_max in y [-0.2, 0.6] 1.542 ± 0.010; x_min in y [-0.2, 0.6] -0.274 ± 0.004; x_max 1.856 ± 0.012; y_min -0.877 ± 0.007; y_max 2.615 ± 0.016; features through the same placement (window: the triangular window through the tower, between the sloped rear leg, the front leg and the gas tube's boss (see-through)) (tools/trace.py)","via":"harvest","note":"BCM's base from its right side: the tower with its wings, the window, the boss, the rings' feet, the swivel's ear and the bayonet lug. Its widths are the CAD set's .750 base's (the part's ledger)."}},"gaps":[{"what":"Its weight","need":"BCM and Primary Arms publish none: the figure is its own steel by the model's volume (5.6 oz). A seller's or a reviewer's weight of the bare base"},{"what":"The F base's own height","need":"A drawing or a maker's figure for the F base's post seat: the .040 over the A2's is Windham Weaponry's (a rifle maker selling a taller post for the A2 base), and BCM says only \"taller\""},{"what":"Its widths","need":"An end-on or a top photo of BCM's base: every width across is the CAD set's .750 base, and BCM's forging differs from it in the side view (its wings 0.04 taller over the bore, its bayonet lug's foot 0.1 higher, its swivel hole 0.04 higher)"},{"what":"Where a gunsmith drills the front taper pin","need":"A drawing of the barrel and base assembly, or a photo of a pinned base from below"}]},"bcm-gi-barrel-nut":{"id":"bcm-gi-barrel-nut","name":"G.I. Barrel Nut - AR15","manufacturer":"BCM","sku":"Barrel-Nut-G.I.","url":"https://bravocompanyusa.com/g-i-barrel-nut-ar15/","category":"barrel_nut","description":"The standard barrel nut: it threads onto the upper receiver's nose and clamps the barrel extension's flange against the receiver's front face, and its toothed flange takes the wrench, the gas tube passing through one of its notches. A delta ring assembly goes on it for a drop-in handguard. BCM: \"Barrel nut for your AR15, M16, M4.\"","weight":"bcm-gi-barrel-nut.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"mount":{"origin":[0,0,0],"note":"Part frame: the receiver's front face on the bore axis, +x toward the muzzle."}},"interfaces":{"handguard_mount":{"type":"ar15.handguard_mount","role":"handguard","anchor":"mount","params":{"nut":"standard"},"flips":false,"note":"BCM: \"Barrel nut for your AR15, M16, M4.\" Its name is the G.I. (mil-spec) nut's; its thread is the receiver's 1.250-18 UNEF (bcm-m4-upper.thread_major_d)."},"delta_ring":{"type":"ar15.delta_ring","role":"nut","anchor":"mount","params":{},"flips":false,"note":"BCM sells the ring, its weld spring and its snap ring apart, as its Delta Ring Assembly (bcm-delta-ring-assembly)."},"drop_in":{"type":"ar15.drop_in","role":"nut","params":{},"flips":false}},"materials":{"nut":{"label":"Barrel nut","finish":"phosphate","recolorable":false,"color":"bcm-barrel-nut-phosphate","note":"Steel by the mil-spec nut's; BCM states no material or finish. Its one photo (references/bcm-gi-barrel-nut c43d94b8ae9c) shows a matte, mottled dark grey, as a manganese phosphate is: phosphate by its look, not by a sentence (Spike's says of its own mil-spec nut \"completed with a phosphate finish\"). One look."}},"components":{},"geometry":{"model":"bcm-gi-barrel-nut.glb","components":{},"approximations":["Every size is the mil-spec nut's as the reference CAD set models it (std.ar15.barrel_nut_*), because BCM states none and names it the G.I. nut; its photo is an oblique from above and isn't measured.","Placed as the Army's assembly has it: its inner shoulder on the barrel extension's flange (std.ar15.barrel_extension_flange_thickness ahead of the receiver's front face), its rear face 0.394 behind that face and 0.051 ahead of the receiver's shoulder. A nut is torqued until a notch lines up with the gas tube: the gap to the shoulder isn't fixed, and this is the model's.","Its internal thread is a helix of the receiver's pitch between the model's minor and major diameters, ending where the receiver's front face stands, turned so that at the top of the turn its roots meet the crests of the upper's thread rings (bcm-m4-upper draws its thread as rings, so round the rest of the turn the two cross by up to the thread's depth).","The twenty notches are the model's round-bottomed slots through the flange, one at the top for the gas tube; how the nut is turned on the thread past that isn't fixed.","Not drawn: the 0.005 in rounds at the snap ring's groove's edges, and the 0.011 in of the minor bore that runs on past the thread's end before the counterbore's chamfer."],"ledger":["bcm-gi-barrel-nut.length","bcm-gi-barrel-nut.flange_diameter","bcm-gi-barrel-nut.notches"]},"profiles":{},"gaps":[{"what":"BCM's own figures","need":"Any size, weight or finish BCM states for this nut: every figure here is the mil-spec nut's"},{"what":"A square view of BCM's nut","need":"A side view of this nut, to read its length and the flange's against the mil-spec figures"}]},"bcm-grip-mod-3":{"id":"bcm-grip-mod-3","name":"Grip Mod 3","manufacturer":"BCM","sku":"BCM-GFG-Mod-3-BLK","url":"https://bravocompanyusa.com/bcm-grip-mod-3-black/","category":"grip","description":"BCM's reduced-angle grip in its wider form (\"Up to a quarter of an inch wider than the BCM® Mod 0 and Mod 1 grips\"): a high beavertail, a tang that reaches forward under the trigger guard, and a hinged trap door over the hollow inside. Its straps lean 20 degrees installed, between the MOE-K2+'s 16 and the MOE+'s 26. On a lower with a trigger guard of its own the tang may be in the way.","weight":"bcm-grip-mod-3.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"grip_lug":{"origin":["-{.seat_x}",0,0],"note":"Grip frame: origin at the rear end of its flat top, which bears on the lower's underside. The anchor is the point of that top at the takedown pin's x once installed (seat_x)."}},"interfaces":{"grip_lug":{"type":"ar15.grip_lug","role":"grip","anchor":"grip_lug","params":{},"flips":false}},"materials":{"body":{"label":"Grip","finish":"polymer","recolorable":true,"color":"placeholder-polymer-black","sheen":"matte","options":{"black":{"label":"Black","finish":"polymer","color":"placeholder-polymer-black","sheen":"matte","sku":"BCM-GFG-Mod-3-BLK","source":"https://bravocompanyusa.com/bcm-grip-mod-3-black/"},"fde":{"label":"Flat Dark Earth","finish":"polymer","color":"bcm-fde","sheen":"matte","sku":"BCM-GFG-Mod-3-FDE","source":"https://bravocompanyusa.com/bcm-grip-mod-3-flat-dark-earth/"},"fg":{"label":"Foliage Green","finish":"polymer","color":"bcm-foliage-green","sheen":"matte","sku":"BCM-GFG-MOD-3-FGREEN","source":"https://dirtybirdusa.com/products/bcmgunfighter-pistol-grip-mod-3/"},"wg":{"label":"Wolf Grey","finish":"polymer","color":"bcm-wolf-gray","sheen":"matte","sku":"BCM-GFG-MOD-3-WG","source":"https://dirtybirdusa.com/products/bcmgunfighter-pistol-grip-mod-3/"}},"default":"black","note":"BCM: \"manufactured from high quality impact resistant polymers\". Black and Flat Dark Earth (BCM-GFG-Mod-3-FDE) are on BCM's shop; Foliage Green and Wolf Grey are named by BCM's parts-kit brochure and sold by Dirty Bird and AR15Discounts under BCM's numbers. One colour all over in each: the hinged door under it is the grip's colour (BCM's Flat Dark Earth photos, Dirty Bird's of the other three); the screw is inside. Black is the catalog's stand-in polymer black (a black isn't fitted to a photo)."}},"components":{"body":{"label":"Grip","material":"body"}},"geometry":{"model":"bcm-grip-mod-3.glb","components":{},"approximations":["Built about the strap's axis from two views: BCM's own photo of the grip lying on its side (scaled by the 4.242 in from its flat top to its toe that a reviewer measured with calipers: the one figure taken on the grip itself. His photo of it beside a Magpul MOE makes it 4.145 in by Magpul's own figure for that grip, so it may be drawn 2% large; no photo of it on a lower has yet been read) and the reviewer's photo of it from behind, lying on its front strap.","Its section is drawn as an ellipse from the back strap to the front strap at every place down the grip: no photo is square to a section. The one check is the texture panel's rear border, which the side view has 0.35 in ahead of the back strap and the view from behind about 0.48 in out from the middle, where an ellipse of the grip's depth and thickness passes.","Side to side it is as the view from behind has it: 0.88 in at the neck, 1.236 in at the upper body (the reviewer's calipers; the Magpul MOE beside it in that photo reads Magpul's 1.2 in at the same scale), widening to 1.36 in at the foot. That photo is taken from close, so some of the widening may be the lens's; its length reads 8% over the side view's and is put to it.","The front strap's ribs are the side view's, cut as far round the strap as that view has them run (0.14 in back from its edge) and fading out there; how deep they are away from the middle isn't seen.","The top block's two walls and the tang are drawn flat-sided at the receiver's width (0.88 in: a photo of the grip on a BCM lower shows the block flush with the receiver's side); the beavertail is as wide, with the notch between its two rails at the tip as the view from behind has it.","The top is cut for the receiver (2026-10-05, as the Magpul grips' are): the slot for the standard lug (the Army drawing's faces), 0.385 in wide and open through the block's front above the tang (two photos of the block's front face put the slot at the lug's own .375 in within what they can tell, a tight fit: it is drawn 0.005 in clear a side); and under the receiver's rear the round of a receiver's underside (half-round across as the reference CAD model has it, along the arc of the fullest forging on file, the Workhorse's), which hollows the beavertail between its two rails.","Not drawn: the screw's hole and the selector spring's hole in the top, the hollow inside, the trap door's seam and the latch's slots, the texture panels and the logo. The hinge's boss at the toe and the door's tab under the base run across the whole foot. The block's edges are broken at 0.02 in.","Seated by its interface, not by a photo of it installed: the block's front face against the rear of the trigger guard's ears, where the Army drawing ends the lug (so a BCM Mod 0 grip sits in the one pin-framed photo on file). On the Workhorse lower the ears are where the drawing has them and the block's front lies against them (until 2026-10-05 that lower's outline, traced in a frame set by its two pins, had them 0.048 in further back, and the block stood that far into them). What the two still share is the tang: its top, as this grip's outline has it, is 1.26 in below the seat, and a receiver's ears reach 1.29 below it (the Workhorse's and the reference CAD model's alike), so the tang stands 0.03 in into their underside (0.002 cubic inches), and as far into the rear end of a trigger guard pinned between them."],"ledger":["bcm-grip-mod-3.grip_angle","bcm-grip-mod-3.bottom_below_lower_underside","bcm-grip-mod-3.thickness","bcm-grip-mod-3.foot_width","bcm-grip-mod-3.top_block_width","bcm-grip-mod-3.rib_reach","bcm-grip-mod-3.overall_height","bcm-grip-mod-3.block_front_x","bcm-grip-mod-3.seat_x","bcm-grip-mod-3.lug_slot_width","std.ar15.grip_lug_width","std.ar15.grip_lug_face_from_pin","std.ar15.grip_lug_face_angle","std.ar15.grip_lug_depth","std.ar15.grip_seat_below_deck","std.ar15.rear_underside_arc_r_fullest","std.ar15.rear_underside_round_r"]},"profiles":{"side":{"plane":"xy","origin":"rear end of the grip's flat top, which bears on the receiver's underside (the grip frame origin)","offset":{},"points":[[-1.574,-3.478],[-1.561,-3.553],[-1.564,-3.613],[-1.541,-3.702],[-1.523,-3.718],[-1.528,-3.724],[-1.516,-3.721],[-1.471,-3.753],[-1.461,-3.749],[-1.437,-3.767],[-1.405,-3.771],[-1.406,-3.784],[-1.38,-3.803],[-1.039,-3.903],[-1.005,-3.91],[-0.977,-3.904],[-0.981,-3.922],[-0.963,-3.942],[-0.337,-4.104],[-0.314,-4.084],[-0.292,-4.098],[-0.307,-4.098],[-0.302,-4.107],[-0.14,-4.149],[-0.119,-4.164],[0.144,-4.238],[0.154,-4.238],[0.151,-4.231],[0.09,-4.217],[0.086,-4.21],[0.095,-4.205],[0.215,-4.242],[0.273,-4.231],[0.333,-4.18],[0.366,-4.175],[0.367,-4.146],[0.397,-4.101],[0.407,-4.041],[0.396,-3.991],[0.306,-3.864],[0.293,-3.82],[0.293,-3.771],[0.306,-3.726],[0.322,-3.716],[0.322,-3.674],[0.339,-3.663],[0.338,-3.625],[0.356,-3.608],[0.355,-3.569],[0.372,-3.558],[0.372,-3.516],[0.389,-3.505],[0.388,-3.467],[0.405,-3.453],[0.405,-3.411],[0.423,-3.398],[0.422,-3.36],[0.439,-3.347],[0.439,-3.306],[0.455,-3.295],[0.456,-3.253],[0.472,-3.242],[0.468,-3.214],[0.49,-3.184],[0.488,-3.15],[0.506,-3.133],[0.505,-3.097],[0.523,-3.079],[0.522,-3.043],[0.539,-3.03],[0.538,-2.992],[0.556,-2.977],[0.555,-2.941],[0.572,-2.925],[0.567,-2.902],[0.585,-2.88],[0.587,-2.838],[0.605,-2.823],[0.603,-2.787],[0.622,-2.769],[0.62,-2.735],[0.637,-2.72],[0.637,-2.682],[0.654,-2.669],[0.655,-2.631],[0.673,-2.616],[0.669,-2.588],[0.69,-2.562],[0.688,-2.526],[0.706,-2.511],[0.705,-2.473],[0.72,-2.466],[0.721,-2.423],[0.738,-2.408],[0.737,-2.372],[0.758,-2.344],[0.754,-2.321],[0.773,-2.306],[0.77,-2.269],[0.791,-2.251],[0.786,-2.218],[0.803,-2.207],[0.802,-2.167],[0.819,-2.154],[0.819,-2.115],[0.835,-2.104],[0.84,-2.086],[0.836,-2.062],[0.851,-2.053],[0.851,-2.013],[0.873,-1.983],[0.868,-1.959],[0.885,-1.948],[0.884,-1.91],[0.9,-1.899],[0.901,-1.856],[0.917,-1.847],[0.92,-1.804],[0.936,-1.793],[0.932,-1.76],[0.953,-1.739],[0.949,-1.707],[0.967,-1.689],[0.965,-1.655],[0.985,-1.591],[1.031,-1.521],[1.074,-1.486],[1.127,-1.46],[1.474,-1.39],[1.567,-1.379],[1.598,-1.349],[1.617,-1.289],[1.606,-1.267],[1.581,-1.26],[1.28,-1.258],[1.265,-1.244],[1.262,-0.962],[1.28,-0.947],[1.283,-0.927],[1.265,-0.902],[1.266,-0.224],[1.248,-0.152],[1.223,-0.108],[1.176,-0.057],[1.105,-0.015],[1.001,0.004],[0.611,-0.003],[-0.001,0.006],[-0.036,0.126],[-0.095,0.261],[-0.165,0.371],[-0.249,0.47],[-0.364,0.57],[-0.475,0.639],[-0.629,0.703],[-0.704,0.715],[-0.76,0.696],[-0.805,0.652],[-0.842,0.56],[-0.876,0.428],[-0.848,0.388],[-0.765,0.339],[-0.714,0.296],[-0.641,0.213],[-0.57,0.094],[-0.544,0.025],[-0.508,-0.146],[-0.482,-0.459],[-0.486,-0.684],[-0.508,-0.838],[-0.561,-1.031],[-0.608,-1.153],[-0.953,-1.793],[-1.075,-2.043],[-1.158,-2.248],[-1.468,-3.067],[-1.536,-3.283]],"scaleRefs":["bcm-grip-mod-3.bottom_below_lower_underside"],"angleRef":"bcm-grip-mod-3.grip_angle","inputs":{"bcm-grip-mod-3.bottom_below_lower_underside":4.242,"bcm-grip-mod-3.grip_angle":19.59},"tolerance":0.006,"photo":"references/bcm-grip-mod-3 bdf41efeff9d (BCM's Mod_3_FDE_3: the FDE grip lying on its right side on white, straight left side, 3700 x 2467)","method":"luminance < 225, inside [900, 0, 2700, 2467], closing ×2, largest piece, holes filled; rotated -15.3° (counter-clockwise) so the edges' mean lean in the band 0.45–0.85 of the height (7.7° rear, 2.4° front in the photo) becomes bcm-grip-mod-3.grip_angle = 19.59°; re-measured 21.4°/17.8°; scale from bcm-grip-mod-3.bottom_below_lower_underside = 4.242 in (y from the origin to the far edge 1970 px → 464.3 px/in); origin at the rear end of the flat top; Douglas-Peucker at 0.006 in with the extremes kept: 177 points (IoU 0.997 with the full outline) (tools/trace.py)","via":"harvest","note":"Includes the beavertail (above the flat top; it tucks under the receiver's rear), the top block with the tang ahead of it, the front strap's ribs, the hinge's boss at the toe and the door's tab under the base. The texture panel, the logo and the latch's slot aren't in an outline."},"rear":{"plane":"zy","origin":"the horns' tips, centred: y runs down the strap's axis (the view is square to it), not down the grip frame's y","offset":{},"points":[[-0.68,-4.759],[-0.672,-4.8],[-0.639,-4.857],[-0.593,-4.886],[0.569,-4.886],[0.639,-4.825],[0.647,-4.775],[0.68,-4.717],[0.68,-4.478],[0.655,-4.149],[0.663,-3.893],[0.647,-3.341],[0.655,-3.102],[0.647,-3.094],[0.647,-2.361],[0.639,-2.353],[0.647,-2.344],[0.639,-1.916],[0.647,-1.908],[0.647,-1.619],[0.639,-1.545],[0.606,-1.438],[0.474,-1.174],[0.449,-1.084],[0.441,-0.754],[0.449,-0.556],[0.433,-0.54],[0.441,-0.507],[0.416,-0.457],[0.408,-0.251],[0.383,-0.078],[0.358,-0.012],[0.338,0],[0.264,-0.082],[0.157,-0.157],[0.049,-0.198],[-0.058,-0.214],[-0.173,-0.206],[-0.264,-0.181],[-0.371,-0.124],[-0.478,-0.016],[-0.49,-0.021],[-0.466,-0.111],[-0.433,-1.149],[-0.466,-1.314],[-0.49,-1.339],[-0.49,-1.364],[-0.556,-1.487],[-0.589,-1.677],[-0.589,-2.122],[-0.606,-2.402],[-0.597,-2.46],[-0.639,-3.687],[-0.63,-3.844],[-0.647,-3.902],[-0.639,-4.083],[-0.663,-4.47],[-0.663,-4.594],[-0.647,-4.66],[-0.672,-4.684]],"scaleRefs":["bcm-grip-mod-3.thickness"],"inputs":{"bcm-grip-mod-3.thickness":1.236},"tolerance":0.008,"photo":"references/bcm-grip-mod-3 7192cb9b2d04 (Santomieri's BCM-Grip-Mod3-03: the Mod 3 lying on its front strap, its back strap straight on from above, a Magpul MOE beside it, 1200 x 797)","method":"luminance < 110, inside [330, 0, 585, 617], closing ×2, largest piece, holes filled; scale from bcm-grip-mod-3.thickness = 1.236 in (median width over 0.34–0.46 of the height from the top, 149–151 px 150 px → 121.4 px/in); origin at x center, y max of the outline; Douglas-Peucker at 0.008 in with the extremes kept: 60 points (IoU 0.995 with the full outline); the door hanging below the base is cut off at row 617; the top block's right wall, lit beside the beavertail (the grip is rolled a few degrees), is under the threshold (tools/trace.py)","via":"harvest","note":"Square to the strap's axis, from close: the beavertail's tip and the heel stand 2 to 3 in over the table and read large against the body's widest (its length reads 6% over the side outline's). The body is scaled where the review's calipers and the MOE beside it agree; its widening toward the foot (10%) is as the photo has it, some of it the lens's."}},"gaps":[{"what":"A size, a weight or an angle from BCM","need":"BCM publishes none: its sizes are one reviewer's calipers, each checked against a photo; a maker's drawing or spec sheet would settle them"},{"what":"The section and the foot's width from a view square to them","need":"a straight rear, front or top view from further away (the only view from behind is a close photo), or a design patent's figures if BCM holds one for this grip"},{"what":"Its seat, its lean and its drop read on the grip itself, installed (it is seated by its interface, and its size is one reviewer's calipers)","need":"a straight side photo of a Mod 3 on a lower with the receiver's pins in view (BCM's FDE photo of one, from the right and a little below, is on file and unread; Wing Tactical's pin-framed photo shows a Mod 0)"},{"what":"Its lug slot's width from a view square to the top (it is read on the block's front face in two oblique photos, and comes to the lug's own width)","need":"a view of a Mod 3's top from above with a scale, or the slot against the top's width in one"},{"what":"The tang against a lower with a trigger guard of its own","need":"the room behind an integral guard (the M4E1's) as a figure; T.REX ARMS says the tang has to be trimmed there"}]},"bcm-grip-mod-4":{"id":"bcm-grip-mod-4","name":"Grip Mod 4","manufacturer":"BCM","sku":"BCM-GFG-MOD-4-BLK","url":"https://bravocompanyusa.com/bcm-grip-mod-4-black/","category":"grip","description":"BCM's newest reduced-angle grip (\"An update to the classic A1 and A2 design ... a new form factor with a reduced angle and a new ultra-tactile grip texture\"): a high beavertail, a tang that reaches forward to the trigger guard, coarse ribs across its front strap, and an open bottom where the Mod 3 has a trap door (\"Open bottom to minimize weight\"). Its straps lean 17.4 degrees installed, less than the Mod 3's 20.","weight":"bcm-grip-mod-4.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"grip_lug":{"origin":["-{.seat_x}",0,0],"note":"Grip frame: origin at the rear end of its flat top, which bears on the lower's underside. The anchor is the point of that top at the takedown pin's x once installed (seat_x)."}},"interfaces":{"grip_lug":{"type":"ar15.grip_lug","role":"grip","anchor":"grip_lug","params":{},"flips":false}},"materials":{"body":{"label":"Grip","finish":"polymer","recolorable":true,"color":"placeholder-polymer-black","sheen":"matte","options":{"black":{"label":"Black","finish":"polymer","color":"placeholder-polymer-black","sheen":"matte","sku":"BCM-GFG-MOD-4-BLK","source":"https://bravocompanyusa.com/bcm-grip-mod-4-black/"},"fde":{"label":"Flat Dark Earth","finish":"polymer","color":"bcm-fde","sheen":"matte","sku":"BCM-GFG-MOD-4-FDE","source":"https://bravocompanyusa.com/bcm-grip-mod-4-flat-dark-earth/"}},"default":"black","note":"BCM: \"Manufactured in the USA from high quality impact resistant polymers.\" Black and Flat Dark Earth (BCM-GFG-MOD-4-FDE) are on BCM's shop, a page each; BCM's brochure for it (bravocompanymfg.com's Mod4_PDF.pdf, read as pictures) says \"The Mod 4 Grip is available in both Black and Flat Dark Earth (FDE)\", AT3 Tactical's page lists the same two, and no page harvested names another. One colour all over in each (BCM's and Primary Arms' photos of both; the open bottom has no door). The FDE is the preset fitted on BCM's Mod 0 stock (bcm-fde, rendered #9d8f7c for its photos' #9a8d7b and #9f907c): BCM's own photo of this grip in FDE reads #a38e76 on the smooth flat under the beavertail (d463bd30844b, [450,190,600,260]), and the preset drawn on this grip in the hero direction on the light backdrop reads #a0927e and #9c8f7c on its side's lit flats (make color-match JOB=bcm-grip-mod-4, in bcm-16-mid): within 3 to 8 levels; Primary Arms' (ac3394366085) reads lighter and pinker, #baa598, as its photos of BCM's other FDE parts do. Black is the catalog's stand-in polymer black (a black isn't fitted to a photo). BCM sells no grey Mod 4: the Wolf Gray of its Mod 3 isn't offered for this grip."}},"components":{"body":{"label":"Grip","material":"body"}},"geometry":{"model":"bcm-grip-mod-4.glb","components":{},"approximations":["Built about the strap's axis from two views: Primary Arms' photo of the black grip, straight right side (BCM's own and Primary Arms' FDE side photos agree with it, IoU 0.98 and 0.98, within 0.027 in), scaled by its drop below the receiver read in Primary Arms' photo of BCM's MK2 lower with this grip on it, framed by that lower's pins at the Army drawing's places (4.179 in); and BCM's photo of it from behind, its back strap straight on, scaled where its body is the 1.239 in that BCM's photo from ahead gives at the scale of the block's two walls, flush with the receiver.","No page gives a size, a weight or an angle: every figure is read on those photos (the ledger says which). The drop rests on one pin-framed photo, ± 0.03 in.","Its section is drawn as an ellipse from the back strap to the front strap at every place down the grip: no photo is square to a section.","Side to side it is as the view from behind has it: 0.89 in at the beavertail and the neck, 1.24 in at the body, widening a little to 1.28 at the foot.","The front strap's ribs are the side view's teeth, cut as far round the strap as that view has them run (0.20 in back from its edge) and fading out there; from ahead they run across the whole front strap, which an ellipse's section reaches only so far round.","The top block's two walls and the tang are drawn flat-sided at the receiver's width (0.88 in: the block lies flush with the receiver's side in the photos of the MK2 lower); the beavertail is as wide, with the saddle between its two horns as the view from behind has it, cut straight through along the grip.","The open bottom is a hollow drawn 0.12 in inside the body's own sections, up to 1.3 in under the flat top, closed there level: neither the rim's width nor the hollow's depth is read (no view is square to the base, and none sees the hollow's top: both are ledger entries marked assumed).","The top is cut for the receiver (lib.grip_receiver_cuts): the slot for the standard lug, 0.394 in wide as BCM's photo from ahead has it between the block's walls, open through the block's front above the tang; and under the receiver's rear the round of a receiver's underside, which hollows the beavertail between its horns.","Seated by its interface, not by a photo of it installed: the block's front face against the rear of the trigger guard's ears, where the Army drawing ends the lug. The outline's lower half fitted into the pin-framed photo puts the origin 0.15 in further back and turns it 2 degrees more upright (a fit 4 in below what it reads; kept in the ledger as readings).","Not drawn: the screw's hole and the selector spring's hole in the top, the texture panels and the star in its ring, and the mounting hardware BCM includes (a screw and a washer, by its page's \"Includes mounting hardware\": no page names or weighs them). The block's edges are broken at 0.02 in."],"ledger":["bcm-grip-mod-4.grip_angle","bcm-grip-mod-4.bottom_below_lower_underside","bcm-grip-mod-4.thickness","bcm-grip-mod-4.foot_width","bcm-grip-mod-4.top_block_width","bcm-grip-mod-4.rib_reach","bcm-grip-mod-4.overall_height","bcm-grip-mod-4.block_front_x","bcm-grip-mod-4.seat_x","bcm-grip-mod-4.lug_slot_width","bcm-grip-mod-4.base_wall","bcm-grip-mod-4.hollow_top_below_top","std.ar15.grip_lug_width","std.ar15.grip_lug_face_from_pin","std.ar15.grip_lug_face_angle","std.ar15.grip_lug_depth","std.ar15.grip_seat_below_deck","std.ar15.rear_underside_arc_r_fullest","std.ar15.rear_underside_round_r"]},"profiles":{"side":{"plane":"xy","origin":"rear end of the grip's flat top, which bears on the receiver's underside (the grip frame origin)","offset":{},"points":[[-1.381,-3.462],[-1.37,-3.588],[-1.348,-3.69],[-1.331,-3.728],[-1.268,-3.784],[-1.106,-3.862],[-0.852,-3.943],[-0.622,-3.991],[-0.244,-4.088],[0.125,-4.166],[0.303,-4.179],[0.371,-4.171],[0.42,-4.149],[0.49,-4.062],[0.521,-4.003],[0.529,-3.956],[0.522,-3.899],[0.492,-3.84],[0.418,-3.756],[0.414,-3.691],[0.42,-3.667],[0.468,-3.626],[0.471,-3.553],[0.503,-3.497],[0.496,-3.452],[0.528,-3.411],[0.525,-3.35],[0.557,-3.31],[0.553,-3.248],[0.589,-3.197],[0.582,-3.143],[0.611,-3.115],[0.617,-3.095],[0.606,-3.042],[0.639,-3.013],[0.646,-2.993],[0.648,-2.966],[0.635,-2.94],[0.661,-2.923],[0.675,-2.896],[0.672,-2.854],[0.66,-2.839],[0.695,-2.82],[0.703,-2.794],[0.706,-2.771],[0.688,-2.738],[0.716,-2.722],[0.732,-2.697],[0.733,-2.654],[0.717,-2.636],[0.754,-2.611],[0.763,-2.58],[0.762,-2.56],[0.745,-2.535],[0.784,-2.507],[0.792,-2.482],[0.791,-2.459],[0.774,-2.429],[0.809,-2.414],[0.821,-2.38],[0.819,-2.354],[0.802,-2.328],[0.834,-2.312],[0.85,-2.283],[0.848,-2.248],[0.831,-2.226],[0.863,-2.211],[0.875,-2.193],[0.877,-2.151],[0.86,-2.128],[0.891,-2.109],[0.907,-2.08],[0.905,-2.053],[0.888,-2.027],[0.901,-2.009],[0.927,-2.004],[0.936,-1.982],[0.934,-1.955],[0.917,-1.925],[0.929,-1.907],[0.956,-1.902],[0.965,-1.884],[0.966,-1.85],[0.946,-1.832],[0.949,-1.816],[0.99,-1.791],[0.995,-1.748],[0.974,-1.726],[0.978,-1.715],[1.009,-1.699],[1.025,-1.67],[1.024,-1.647],[1.003,-1.621],[1.029,-1.543],[1.067,-1.479],[1.099,-1.452],[1.538,-1.346],[1.601,-1.319],[1.621,-1.289],[1.614,-1.243],[1.585,-1.232],[1.297,-1.241],[1.268,-1.229],[1.26,-0.239],[1.226,-0.133],[1.197,-0.085],[1.154,-0.04],[1.078,0.002],[1.016,0.014],[0.974,0.011],[0.967,0.003],[0.913,0],[0.882,0.01],[0.875,0.002],[0.81,-0.002],[0.725,0.008],[0.211,0.001],[0.131,-0.008],[0.122,0],[0.042,-0.005],[0.001,0.002],[-0.023,0.085],[-0.08,0.216],[-0.131,0.301],[-0.227,0.419],[-0.342,0.518],[-0.461,0.591],[-0.544,0.632],[-0.669,0.667],[-0.715,0.665],[-0.779,0.645],[-0.822,0.61],[-0.851,0.532],[-0.851,0.39],[-0.757,0.332],[-0.642,0.233],[-0.58,0.152],[-0.502,0.003],[-0.466,-0.148],[-0.424,-0.411],[-0.415,-0.618],[-0.437,-0.842],[-0.493,-1.064],[-0.573,-1.264],[-0.709,-1.506],[-0.856,-1.807],[-1.041,-2.248],[-1.237,-2.839],[-1.324,-3.132],[-1.37,-3.331]],"scaleRefs":["bcm-grip-mod-4.bottom_below_lower_underside"],"angleRef":"bcm-grip-mod-4.grip_angle","inputs":{"bcm-grip-mod-4.bottom_below_lower_underside":4.179,"bcm-grip-mod-4.grip_angle":17.4},"tolerance":0.006,"photo":"references/bcm-grip-mod-4 87b3693f2d0e (Primary Arms BCM-GFG-MOD-4-BLK_01: the black grip on white, straight right side, 2200 x 1467)","method":"luminance < 200, closing ×2, largest piece, holes filled; rotated +3.4° (counter-clockwise) so the edges' mean lean in the band 0.45–0.85 of the height (21.9° rear, 19.1° front in the photo) becomes bcm-grip-mod-4.grip_angle = 17.4°; re-measured 19.2°/15.6°; scale from bcm-grip-mod-4.bottom_below_lower_underside = 4.179 in (y from the origin to the far edge 1090 px → 260.9 px/in); origin at the rear end of the flat top; Douglas-Peucker at 0.006 in with the extremes kept: 150 points (IoU 0.997 with the full outline) (tools/trace.py)","via":"harvest","note":"Includes the beavertail (above the flat top; it tucks under the receiver's rear), the top block with the tang ahead of it, the front strap's ribs and the foot's flare. The texture panel and the star in its ring aren't in an outline."},"rear":{"plane":"zy","origin":"the beavertail's tips, centred: y runs down the back strap (the view is square to it), not down the grip frame's y","offset":{},"points":[[-0.653,-4.46],[-0.598,-4.542],[-0.526,-4.586],[-0.447,-4.615],[-0.231,-4.658],[-0.007,-4.672],[0.26,-4.658],[0.433,-4.622],[0.57,-4.564],[0.602,-4.539],[0.638,-4.481],[0.638,-3.976],[0.624,-3.962],[0.631,-3.71],[0.616,-3.666],[0.616,-3.032],[0.624,-2.989],[0.645,-2.967],[0.631,-2.844],[0.645,-2.455],[0.638,-2.304],[0.653,-2.217],[0.631,-2.188],[0.631,-2.087],[0.616,-2.059],[0.631,-2.022],[0.631,-1.395],[0.616,-1.237],[0.609,-1.208],[0.573,-1.164],[0.58,-1.136],[0.544,-1.078],[0.53,-1.013],[0.512,-1.017],[0.487,-0.984],[0.516,-0.963],[0.505,-0.945],[0.49,-0.959],[0.472,-0.941],[0.465,-0.746],[0.487,-0.097],[0.479,-0.032],[0.454,-0.007],[0.429,-0.068],[0.375,-0.13],[0.357,-0.112],[0.361,-0.101],[0.26,-0.101],[0.238,-0.115],[0.205,-0.155],[0.205,-0.198],[0.22,-0.227],[0.187,-0.252],[0.108,-0.274],[-0.022,-0.274],[-0.166,-0.231],[-0.184,-0.213],[-0.169,-0.198],[-0.169,-0.155],[-0.209,-0.108],[-0.292,-0.105],[-0.242,-0.155],[-0.26,-0.173],[-0.328,-0.105],[-0.389,0],[-0.415,-0.047],[-0.422,-1.02],[-0.454,-1.053],[-0.479,-1.027],[-0.465,-0.977],[-0.472,-0.948],[-0.501,-1.049],[-0.544,-1.136],[-0.544,-1.179],[-0.566,-1.208],[-0.58,-1.294],[-0.595,-1.316],[-0.588,-1.453],[-0.602,-1.525],[-0.602,-1.676],[-0.588,-1.698],[-0.602,-1.813],[-0.588,-1.828],[-0.602,-1.842],[-0.602,-1.943],[-0.588,-1.958],[-0.588,-1.986],[-0.602,-2.001],[-0.595,-2.087],[-0.609,-2.116],[-0.595,-2.174],[-0.624,-2.21],[-0.624,-2.83],[-0.609,-2.852],[-0.624,-2.873],[-0.624,-2.974],[-0.609,-2.989],[-0.609,-3.335],[-0.624,-3.472],[-0.616,-3.565],[-0.638,-3.984],[-0.631,-4.099],[-0.645,-4.135],[-0.638,-4.279]],"scaleRefs":["bcm-grip-mod-4.thickness"],"inputs":{"bcm-grip-mod-4.thickness":1.239},"tolerance":0.008,"photo":"references/bcm-grip-mod-4 645f67d84699 (BCM's BCM-MOD-4-GRIP-BLK-3: the black grip from behind, its back strap straight on, cut out on white, 1000 x 1000)","method":"luminance < 200, closing ×2, largest piece, holes filled; scale from bcm-grip-mod-4.thickness = 1.239 in (median width over 0.31–0.75 of the height from the top, 169–177 px 172 px → 138.7 px/in); origin at x center, y max of the outline; Douglas-Peucker at 0.008 in with the extremes kept: 104 points (IoU 0.994 with the full outline); checks: width 1.305 ± 0.068 in vs bcm-grip-mod-4.foot_width 1.279 ± 0.062 (provisional): agrees; median row width in y [-0.9, -0.2] (0.880–0.894) 0.887 ± 0.049 in vs bcm-grip-mod-4.top_block_width 0.88 ± 0.04 (provisional): agrees (tools/trace.py)","via":"harvest","note":"Square to the back strap: the beavertail is as wide as the block (123 to 124 px against the body's 170 to 175), the body widens a little to the foot (178 px), and the foot's rim stands under it."}},"gaps":[{"what":"A size, a weight or an angle from BCM","need":"BCM publishes none (its two shop pages, its marketing site's two pages, and Primary Arms', KYGUNCO's, Rainier Arms' and AT3 Tactical's pages were read): a maker's drawing, or a reviewer's calipers and scale, would settle them"},{"what":"The open bottom's rim and how deep the hollow goes","need":"a view square to the base from below, with the foot's outline in it, and a section or a reviewer's description of the hollow"},{"what":"The section from a view square to it","need":"a straight view from the base or the top from further away, or a design patent's figures if BCM holds one for this grip (no patent marking page of BCM's was found)"},{"what":"Its weight","need":"a weighed figure (the model's polymer volume times a polyamide's density stands for it, without the screw and washer)"}]},"bcm-h-buffer":{"id":"bcm-h-buffer","name":"H Carbine Buffer","manufacturer":"BCM","sku":"Buffer-Carbine-H","url":"https://bravocompanyusa.com/h-carbine-buffer/","category":"buffer","description":"A heavier carbine buffer: the same body as the standard one, with one tungsten and two steel weights inside it. BCM: \"H (Heavy) Buffer for your carbine, AR15, M4 Standard USGI part for the M4 Carbine.\" \"Weighted with 1 tungsten and 2 steel weights. 3.8oz.\" The buffer in BCM's own 16 in mid-length rifle (bravocompanymfg.com, RECCE-16 MCMR: \"USGI H Buffer (1 USGI Tungsten, 2 Steel)\"). Primary Arms calls the same number H1. A heavier buffer slows the bolt carrier; which weight a rifle wants depends on its gas system and what is on its muzzle, and no page on file says it for a build as a rule.","weight":"bcm-h-buffer.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"bore":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the buffer's axis at its head's front face, +x rearward."}},"interfaces":{"bore":{"type":"ar15.extension_bore","role":"buffer","anchor":"bore","params":{},"flips":false}},"materials":{"body":{"label":"Buffer body","finish":"anodized_matte","recolorable":false,"color":"bcm-buffer-anodize","note":"The tan anodized body of BCM's side photo (c75e44c92794), which is the same file on its Carbine, H, H2 and H3 pages. Primary Arms' photos of the heavier buffers show a duller grey-tan with the finish rubbed pale in places: one unit each, in another light. BCM states neither material nor finish."},"bumper":{"label":"Bumper","finish":"polymer","recolorable":false,"color":"bcm-buffer-bumper","note":"Cream in BCM's side photo, the one file for all four weights; a pale green on the H buffer in Primary Arms'. The Army's drawing (8448619): \"RUBBER, POLYETHER URETHANE, CASTABLE, SHORE A DUROMETER 95±3\"."},"pin":{"label":"Pin","finish":"steel","recolorable":false,"color":"steel-phosphate-dark","note":"The spring pin through the body and the bumper: a dark dot in a hole in BCM's side photo."}},"components":{},"geometry":{"model":"bcm-h-buffer.glb","components":{},"approximations":["The standard carbine buffer's shape, as BCM's standard buffer is drawn (the Army's drawings of the buffer's head, bumper and pin and the carbine body of the reference CAD set): BCM states no size for any of its four, and shows one side photo for all of them.","Not drawn: what makes it this weight, the one tungsten and two steel weights inside it; and the H stamped on its head's rear face (BCM's photo ed0bf1d1faa7), which is how one is told from another."],"ledger":["bcm-h-buffer.length","bcm-h-buffer.od","std.carbine_buffer.head_thickness","std.carbine_buffer.body_d","std.carbine_buffer.bumper_exposed"]},"profiles":{},"gaps":[{"what":"Its own sizes","need":"BCM's figures or a photo with scale: its length, head and body are the standard pattern's"}]},"bcm-h2-buffer":{"id":"bcm-h2-buffer","name":"H2 Carbine Buffer","manufacturer":"BCM","sku":"Buffer-Carbine-H2","url":"https://bravocompanyusa.com/h2-carbine-buffer/","category":"buffer","description":"A heavier carbine buffer: the same body as the standard one, with two tungsten weights and one steel inside it. BCM: \"H2 (Heavy) Buffer for your carbine, AR15, M4 Standard USGI part for the M4A1 Carbine.\" \"Weighted with 2 tungsten and 1 steel weights. 4.6oz.\" A heavier buffer slows the bolt carrier; which weight a rifle wants depends on its gas system and what is on its muzzle, and no page on file says it for a build as a rule.","weight":"bcm-h2-buffer.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"bore":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the buffer's axis at its head's front face, +x rearward."}},"interfaces":{"bore":{"type":"ar15.extension_bore","role":"buffer","anchor":"bore","params":{},"flips":false}},"materials":{"body":{"label":"Buffer body","finish":"anodized_matte","recolorable":false,"color":"bcm-buffer-anodize","note":"The tan anodized body of BCM's side photo (c75e44c92794), which is the same file on its Carbine, H, H2 and H3 pages. Primary Arms' photos of the heavier buffers show a duller grey-tan with the finish rubbed pale in places: one unit each, in another light. BCM states neither material nor finish."},"bumper":{"label":"Bumper","finish":"polymer","recolorable":false,"color":"bcm-buffer-bumper","note":"Cream in BCM's side photo, the one file for all four weights; a pale green on the H buffer in Primary Arms'. The Army's drawing (8448619): \"RUBBER, POLYETHER URETHANE, CASTABLE, SHORE A DUROMETER 95±3\"."},"pin":{"label":"Pin","finish":"steel","recolorable":false,"color":"steel-phosphate-dark","note":"The spring pin through the body and the bumper: a dark dot in a hole in BCM's side photo."}},"components":{},"geometry":{"model":"bcm-h2-buffer.glb","components":{},"approximations":["The standard carbine buffer's shape, as BCM's standard buffer is drawn (the Army's drawings of the buffer's head, bumper and pin and the carbine body of the reference CAD set): BCM states no size for any of its four, and shows one side photo for all of them.","Not drawn: what makes it this weight, the two tungsten weights and one steel inside it; and the H2 stamped on its head's rear face (BCM's photo 1b8e78df0d6a), which is how one is told from another."],"ledger":["bcm-h2-buffer.length","bcm-h2-buffer.od","std.carbine_buffer.head_thickness","std.carbine_buffer.body_d","std.carbine_buffer.bumper_exposed"]},"profiles":{},"gaps":[{"what":"Its own sizes","need":"BCM's figures or a photo with scale: its length, head and body are the standard pattern's"}]},"bcm-h3-buffer":{"id":"bcm-h3-buffer","name":"H3 Carbine Buffer","manufacturer":"BCM","sku":"Buffer-Carbine-H3","url":"https://bravocompanyusa.com/h3-carbine-buffer/","category":"buffer","description":"A heavier carbine buffer: the same body as the standard one, with three tungsten weights inside it. BCM: \"H3 (Heavy) Buffer for your carbine, AR15, M4\" \"Weighted with 3 tungsten weights. 5.4oz.\" A heavier buffer slows the bolt carrier; which weight a rifle wants depends on its gas system and what is on its muzzle, and no page on file says it for a build as a rule.","weight":"bcm-h3-buffer.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"bore":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the buffer's axis at its head's front face, +x rearward."}},"interfaces":{"bore":{"type":"ar15.extension_bore","role":"buffer","anchor":"bore","params":{},"flips":false}},"materials":{"body":{"label":"Buffer body","finish":"anodized_matte","recolorable":false,"color":"bcm-buffer-anodize","note":"The tan anodized body of BCM's side photo (c75e44c92794), which is the same file on its Carbine, H, H2 and H3 pages. Primary Arms' photos of the heavier buffers show a duller grey-tan with the finish rubbed pale in places: one unit each, in another light. BCM states neither material nor finish."},"bumper":{"label":"Bumper","finish":"polymer","recolorable":false,"color":"bcm-buffer-bumper","note":"Cream in BCM's side photo, the one file for all four weights; a pale green on the H buffer in Primary Arms'. The Army's drawing (8448619): \"RUBBER, POLYETHER URETHANE, CASTABLE, SHORE A DUROMETER 95±3\"."},"pin":{"label":"Pin","finish":"steel","recolorable":false,"color":"steel-phosphate-dark","note":"The spring pin through the body and the bumper: a dark dot in a hole in BCM's side photo."}},"components":{},"geometry":{"model":"bcm-h3-buffer.glb","components":{},"approximations":["The standard carbine buffer's shape, as BCM's standard buffer is drawn (the Army's drawings of the buffer's head, bumper and pin and the carbine body of the reference CAD set): BCM states no size for any of its four, and shows one side photo for all of them.","Not drawn: what makes it this weight, the three tungsten weights inside it; and the H3 stamped on its head's rear face (BCM's photo 7cc6455f866d), which is how one is told from another."],"ledger":["bcm-h3-buffer.length","bcm-h3-buffer.od","std.carbine_buffer.head_thickness","std.carbine_buffer.body_d","std.carbine_buffer.bumper_exposed"]},"profiles":{},"gaps":[{"what":"Its own sizes","need":"BCM's figures or a photo with scale: its length, head and body are the standard pattern's"}]},"bcm-handguard-cap-round-750":{"id":"bcm-handguard-cap-round-750","name":"Handguard Cap Round - .750 AR15","manufacturer":"BCM","sku":"Handguard-Cap-Round-.750-AR15","url":"https://bravocompanyusa.com/handguard-cap-round-750-ar15","category":"handguard_cap","description":"BCM: \"Handguard Cap for your AR15, M16, M4. Round caps are typically used on barrels with a standard carbine length gas system. For .750 Diameter Barrel\". The cap behind the front sight base that holds the front of a drop-in handguard: the round one, the M4's.","weight":"bcm-handguard-cap-round-750.weight","occupies":[],"integral":[],"brings":[],"seats":{"handguard":{"parentInterface":"handguard_front","interface":"cap_seat","apart":[0,-1,0],"optional":true,"note":"A drop-in handguard's front flange goes in to the inside of the cap's face, and the delta ring gives way behind it on its spring (D97, ar15.handguard_front). A handguard that states no cap_seat (a free-float one) stays where the platform mates it."}},"requires":[],"anchors":{"seat":{"origin":[0,0,0],"note":"Part frame: on the bore axis at its front face, which bears on the front sight base's rear face, +x toward the muzzle."},"rim":{"origin":["-{.length}",0,0],"note":"The skirt's open edge (its lip), on the bore axis: where a drop-in handguard's front goes in. The lip is lip_len long and lip_od across outside; behind it the skirt is skirt_od."},"pocket":{"origin":["-{.sheet}",0,0],"note":"The face's inside (rear) surface, on the bore axis: how far forward a handguard's front can go in the skirt. Inside, the skirt is skirt_od less the sheet twice (lip_od less it at the lip), and the two tabs at the sides stand in to tab_set_r less the sheet for the bend's first tab_bend_x."}},"interfaces":{"handguard_front":{"type":"ar15.handguard_front","role":"cap","anchor":"pocket","params":{},"flips":false},"handguard_cap":{"type":"ar15.handguard_cap","role":"cap","anchor":"seat","params":{"journal_od":"={.journal_id}"},"flips":false},"drop_in":{"type":"ar15.drop_in","role":"cap","params":{"shape":"round"},"flips":false}},"materials":{"cap":{"label":"Handguard cap","finish":"phosphate","recolorable":false,"color":"bcm-cap-phosphate-round","note":"BCM states neither material nor finish. Its one photo of the cap (6aea7065ddd1) shows a matte, grainy grey with a little olive in it, as a manganese phosphate is: phosphate by its look, not by a sentence, and its colour fitted to that photo (bcm-cap-phosphate-round, data/colors/bcm.yaml). One colour sold."}},"components":{},"geometry":{"model":"bcm-handguard-cap-round-750.glb","components":{},"approximations":["Its sizes are the CAD reference set's round cap (a third-party model of the mil-spec part, bored for a .750 journal): BCM gives only its journal. BCM's photo agrees with it where it can be read: the bore against the rim (0.444 to the model's 0.4436), an oblong hole over the bore, a tab at each side.","The bore is the reference model's, a thousandth over BCM's journal; the edges' small rounds (0.076 mm in the model) are square.","Not drawn: the stamping's dents and any marking (none shows)."],"ledger":["bcm-handguard-cap-round-750.journal_id","bcm-handguard-cap-round-750.length","bcm-handguard-cap-round-750.width","bcm-handguard-cap-round-750.height"]},"profiles":{},"gaps":[{"what":"Its weight","need":"BCM states no weight, material or finish: the weight is its steel worked out from the reference model's sizes. A seller's weight of BCM's cap itself"},{"what":"Its skirt and lip as BCM makes them","need":"BCM's one photo is of the face: the skirt, its lip and the tabs' depth are the reference model's. A photo of the cap from behind or edge-on"}]},"bcm-handguard-cap-triangle-750":{"id":"bcm-handguard-cap-triangle-750","name":"Handguard Cap Triangle - .750 AR15","manufacturer":"BCM","sku":"Handguard-Cap-Triangle-.750","url":"https://bravocompanyusa.com/handguard-cap-triangle-750-ar15/","category":"handguard_cap","description":"BCM: \"Handguard Cap for your AR15, M16, M4. Triangle are typically used on AR15 barrels with a mid length or rifle length gas system. For .750 Diameter Barrel\". The cap behind the front sight base that holds the front of a drop-in handguard: the triangular one, for the M16A1's vertically split handguards and the drop-ins made to take it.","weight":"bcm-handguard-cap-triangle-750.weight","occupies":[],"integral":[],"brings":[],"seats":{"handguard":{"parentInterface":"handguard_front","interface":"cap_seat","apart":[0,-1,0],"optional":true,"note":"A drop-in handguard's front flange goes in to the inside of the cap's face, and the delta ring gives way behind it on its spring (D97, ar15.handguard_front). A handguard that states no cap_seat (a free-float one) stays where the platform mates it."}},"requires":[],"anchors":{"seat":{"origin":[0,0,0],"note":"Part frame: on the bore axis at its front face (the collar's front end), which bears on the front sight base's rear face, +x toward the muzzle."},"rim":{"origin":["-{.length}",0,0],"note":"The skirt's open edge (its lip), on the bore axis: where a drop-in handguard's front flange goes in. The drawing's .328 REF behind the front face."},"pocket":{"origin":["-{.collar} - {.sheet}",0,0],"note":"The face's inside (rear) surface, on the bore axis: how far forward a handguard's front flange can go in the skirt (the pocket is skirt_depth from rim to here). The skirt's inside is the face's outline (corner_r on corner_circle_r, side_r) moved in by the sheet's thickness all round."}},"interfaces":{"handguard_front":{"type":"ar15.handguard_front","role":"cap","anchor":"pocket","params":{},"flips":false},"handguard_cap":{"type":"ar15.handguard_cap","role":"cap","anchor":"seat","params":{"journal_od":"={.journal_id}"},"flips":false},"drop_in":{"type":"ar15.drop_in","role":"cap","params":{"shape":"triangle"},"flips":false}},"materials":{"cap":{"label":"Handguard cap","finish":"phosphate","recolorable":false,"color":"bcm-cap-phosphate-triangle","note":"BCM states neither material nor finish. The Army's drawing: \"STEEL, CMPSN 1045 THRU 1070\", finish \"5.3.1.2 OF MIL-STD-171\"; Windham Weaponry's triangular .750 cap (another maker's) \"finished in black manganese phosphate\" (https://shop.windhamweaponry.com/?p=1377). BCM's one photo of the cap (f771ddce876e) shows a matte dark grey with a soft sheen: phosphate, its colour fitted to that photo (bcm-cap-phosphate-triangle, data/colors/bcm.yaml). One colour sold."}},"components":{},"geometry":{"model":"bcm-handguard-cap-triangle-750.glb","components":{},"approximations":["Its shape is the Army's drawing 8448564 (the .625 cap's), at BCM's .750 bore: BCM gives only its journal. The triangle, the sheet, the depth, the collar and the gas tube's hole are taken to be the drawing's for the .750 cap too (it fits the same handguards and the same gas tube); BCM's one photo (500 x 456, the face from a little below and to the right) agrees as far as it can say: its outline 390 px across and its bore's opening 173 (.cache/batch15/bcm-handguard-cap-round-750/scripts/rows.py), 2.4% wider than the drawing's 1.656 at BCM's bore, about what the bore's wall hides of the opening at that angle; its height over its width 0.96 to the drawing's 0.98, the view's tilt; the gas tube's hole over the top corner.","The bore is BCM's journal and the drawing's clearance over its own (.625 +.005): the middle of a band of five thousandths.","The collar round the bore is the drawing's (.063 -.010 ahead of the face): BCM's 500 px photo of the face neither shows its outside nor rules it out; the bore's wall it shows is deeper than the sheet alone, as the collar's would be.","The bend from the face to the skirt is a round of the drawing's .09 R outside and that less the sheet inside; the collar's root (.016 R MAX) and the edges' break (\"BREAK SHARP EDGES .010 R MAX\") are square.","The skirt's open edge is straight, as the drawing's section has it. Linemount's reproduction cap (another maker's) shows a flared lip there; BCM's photo is of the face and doesn't show the edge.","Not drawn: the bends and dents a stamping leaves, and any marking (none shows)."],"ledger":["bcm-handguard-cap-triangle-750.journal_id","bcm-handguard-cap-triangle-750.length","bcm-handguard-cap-triangle-750.width","bcm-handguard-cap-triangle-750.height"]},"profiles":{},"gaps":[{"what":"Its weight","need":"BCM states no weight, material or finish: the weight is its steel worked out from the drawing's sizes (Linemount's figure for its own triangular cap, 0.3 oz, agrees). A seller's weight of BCM's cap itself"},{"what":"Its skirt, its lip and its collar as BCM makes them","need":"No view of BCM's cap from the side or from behind: they are the Army's drawing's. A photo of the cap from behind or edge-on"}]},"bcm-kag-mlok":{"id":"bcm-kag-mlok","name":"KAG (M-LOK® Compatible*)","manufacturer":"BCM","sku":"BCM-KAG-MCMR-BLK","url":"https://bravocompanyusa.com/bcm-kag-black-m-lok-compatible/","category":"hand_stop","description":"BCM's Kinesthetic Angled Grip, made with Travis Haley: a short polymer grip that bolts into one M-LOK slot with two T-nuts. BCM: \"Forward rake gives positive retention when using \"C-clamp\" (thumb over bore) method of handguard support\", \"Works as a rest for supported firing positions\", \"Small profile is just enough to get repeatable hand position on weapon forend\", \"Textured in front and back for positive engagement\". Black and Flat Dark Earth. An angled grip and a hand stop, not a vertical grip: what a vertical grip makes of a pistol under the law (D93) is read of the vertical_grip kind, and this part isn't one.","weight":"bcm-kag-mlok.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"lug":{"origin":["{.lug_x} + {std.mlok.interval} / 2",0,0],"note":"The middle of its two T-nuts on the mounting face (the plate's rim, which bears on the handguard): one in each half of a slot, the M-LOK interval apart (its nuts read 0.777 in apart on BCM's side view, the interval less 1.3%). The rear nut's screw comes up the deep end from the bore in its toe, the front one's through the tail from the counterbore in its underside. Hand stop frame: origin at the plate's rear end (the deep end's lip) on the mounting face, +x forward along the handguard, +y out of the face into the grip."}},"interfaces":{"mlok":{"type":"mlok","role":"accessory","anchor":"lug","params":{"lugs":"={.lugs}","reach_inside":"={.reach_inside}"},"flips":true,"note":"One slot: its two nuts the M-LOK interval apart, both in the slot under the plate's middle (the plate is 2.73 in long, a little under two slot pitches). How far the nuts reach inside isn't published."}},"materials":{"body":{"label":"Grip","finish":"polymer","recolorable":true,"color":"placeholder-polymer-black","sheen":"matte","options":{"black":{"label":"Black","finish":"polymer","color":"placeholder-polymer-black","sheen":"matte","sku":"BCM-KAG-MCMR-BLK","source":"https://bravocompanyusa.com/bcm-kag-black-m-lok-compatible/"},"fde":{"label":"Flat Dark Earth","finish":"polymer","color":"bcm-fde","sheen":"matte","sku":"BCM-KAG-MCMR-FDE","source":"https://bravocompanyusa.com/bcm-kag-flat-dark-earth-m-lok-compatible/"}},"default":"black","note":"BCM: \"Made in the U.S.A. from high quality, impact resistant polymers.\" Black (BCM-KAG-MCMR-BLK) and Flat Dark Earth (BCM-KAG-MCMR-FDE), a page each on BCM's shop; T.REX ARMS sells the two too. One colour all over in each: BCM's own FDE photos (-2 to -4) and T.REX's have the whole moulding tan, its face's hollow and the cups included. The FDE is BCM's polymer FDE as matched on its Mod 0 stock (bcm-fde), not fitted again on the KAG; black is the catalog's stand-in polymer black (a black isn't fitted). The KeyMod and Picatinny KAGs, and the Picatinny one's Wolf Gray, are other products."},"screws":{"label":"Screws","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The two socket-head screws that hold the T-nuts, seen from below: the front one's head in the counterbore in the tail's underside, the rear one's far up the bore in the toe. Black on the black moulding (Rifle Supply 1858_EDIT-4, BCM's -4) and on the FDE alike (BCM's FDE -3), so a piece of its own with one look. The T-nuts (grey steel) are inside the handguard once tightened and aren't drawn."}},"components":{},"geometry":{"model":"bcm-kag-mlok.glb","components":{},"approximations":["The side outline is BCM's own straight side view of its left, scaled by the length read on Rifle Supply's square photo of it fitted (that handguard's M-LOK slots, the standard's 40 mm pitch). BCM's photo, at that scale, puts its two T-nuts 0.777 in apart, the M-LOK interval less 1.3%: the check, which the scale wasn't set by. Its height on that outline is 1.721 in; on the installed photo 1.684 (the ledger adopts that one).","Run straight across at the width (0.65 ± 0.05 in, read on a face-on photo taken a little from one side, against its nuts' interval): the deep end is the plate's width in the views from below, and no view square to the part's end is on file. Its plan is a rounded rectangle at that width, its corners 0.08 in round.","The outline is cleaned in the script (2026-10-20): the photo's pixel steps smoothed out along it, the ribs' teeth taken out of it and the outline put at the ribs' tips, and the bump under the ramp at the front nut's x taken out (it is the front screw's head, which the side view shows standing out of the ribs' tips by up to 0.02 in; the screw is drawn there).","The ribs (BCM: \"Textured in front and back\") are grooves cut across it at the pitch read on BCM's side view (0.061 in), 0.022 in wide and 0.025 in deep (the gaps and the teeth in that view's silhouette), square to the outline and through the sides as the side view's silhouette shows them: along the tail's underside from the tip and down the deep end's front face to 1.315 in below the face, and down the back face from 0.159 to 1.058 in (16 ribs, counted on the photo, evenly spaced along it; the front run's 38 are its length over the pitch, and an eye count gives 39 ± 2). Their counts are in the manifest's `ribs`; a groove's floor is flat.","The face that bears on the handguard is a rim 0.10 in wide round a hollow; the hollow's depth (0.06 in) is assumed, and the nuts' posts and the moulded words in it aren't drawn.","The cup in each side of the deep end is its outline below 0.40 in from the face and behind 0.96 in, a rim's width (0.10) in from its edges, 0.05 in deep (assumed); the BCM and M-LOK marks in and beside it aren't drawn.","The rear screw's head stands 0.75 in up the toe's 0.42 in bore (assumed: it is seen well down the bore, how far isn't); the front one's in a 0.34 in counterbore square to the ramp, its head standing 0.02 in out of the ribs' tips as the side view has it. Each head is a 0.25 in dome, 0.55 of its width high (a socket button head's proportion), its hex socket not drawn. The three slots each side of the bore in the toe's end face aren't drawn.","Edges rounded at 0.03 in (assumed), on the clean outline before anything is cut: built as four layers that step each edge through a quarter circle (steps of a third of the round), each layer's outline cleared of the loops an inset makes at the rear corner's tight turn (2026-10-20: they had folded the sides' faces there). The script checks that the round took and that no layer crosses itself. The cuts' own edges (the hollow, the cups, the grooves, the bores) are left sharp; where a groove runs out through the rounded side it shows the round's steps.","Its weight is worked out: the model's polymer volume times a nylon's density (BCM names no polymer and states no weight). The moulding may be cored inside where no view shows it."],"ledger":["bcm-kag-mlok.length","bcm-kag-mlok.height","bcm-kag-mlok.width","bcm-kag-mlok.lug_x","bcm-kag-mlok.nut_spacing","bcm-kag-mlok.plan_corner","bcm-kag-mlok.face_rim","bcm-kag-mlok.face_hollow_depth","bcm-kag-mlok.cup_top","bcm-kag-mlok.cup_front","bcm-kag-mlok.cup_rim","bcm-kag-mlok.cup_depth","bcm-kag-mlok.toe_bore","bcm-kag-mlok.toe_bore_depth","bcm-kag-mlok.tail_counterbore","bcm-kag-mlok.screw_head","bcm-kag-mlok.edge_round","bcm-kag-mlok.rib_pitch","bcm-kag-mlok.rib_gap","bcm-kag-mlok.rib_depth","bcm-kag-mlok.ribs_front_from_x","bcm-kag-mlok.ribs_front_to_y","bcm-kag-mlok.ribs_back_from_y","bcm-kag-mlok.ribs_back_to_y","bcm-kag-mlok.front_head_proud","bcm-kag-mlok.ribs_back_count","std.mlok.interval"]},"profiles":{"side":{"plane":"xy","origin":"the plate's rear end, the deep end's lip, on the mounting face","offset":{},"points":[[0,0.115],[0.006,0.109],[0.003,0.096],[0.012,0.087],[0.003,0.081],[0.009,0.047],[0,0.032],[0,0.017],[0.014,0.003],[0.038,0],[2.701,0],[2.721,0.008],[2.724,0.023],[2.718,0.029],[2.73,0.041],[2.73,0.063],[2.715,0.075],[2.709,0.093],[2.718,0.102],[2.706,0.118],[2.706,0.13],[2.693,0.139],[2.699,0.145],[2.658,0.183],[2.637,0.196],[2.621,0.196],[2.626,0.185],[2.621,0.18],[2.612,0.196],[2.606,0.193],[2.591,0.208],[2.57,0.214],[2.557,0.211],[2.548,0.226],[2.499,0.26],[2.414,0.284],[2.407,0.281],[2.395,0.29],[2.34,0.3],[2.313,0.312],[2.279,0.312],[2.23,0.333],[2.209,0.333],[2.148,0.355],[2.129,0.355],[2.114,0.364],[2.086,0.364],[2.028,0.385],[1.995,0.388],[1.946,0.407],[1.94,0.404],[1.863,0.422],[1.756,0.459],[1.732,0.459],[1.714,0.48],[1.701,0.477],[1.677,0.507],[1.631,0.535],[1.619,0.535],[1.603,0.553],[1.573,0.556],[1.53,0.596],[1.472,0.627],[1.466,0.624],[1.426,0.639],[1.377,0.639],[1.368,0.645],[1.356,0.636],[1.35,0.642],[1.328,0.636],[1.295,0.642],[1.282,0.651],[1.273,0.648],[1.264,0.657],[1.246,0.66],[1.209,0.688],[1.197,0.694],[1.191,0.691],[1.16,0.721],[1.136,0.728],[1.131,0.732],[1.134,0.741],[1.117,0.764],[1.111,0.767],[1.099,0.761],[1.091,0.769],[1.101,0.781],[1.094,0.809],[1.075,0.813],[1.067,0.824],[1.082,0.839],[1.076,0.851],[1.079,0.864],[1.058,0.873],[1.058,0.885],[1.076,0.894],[1.076,0.922],[1.061,0.931],[1.061,0.94],[1.068,0.948],[1.085,0.949],[1.088,0.977],[1.076,0.992],[1.084,1.003],[1.096,1.003],[1.104,1.016],[1.107,1.032],[1.091,1.041],[1.091,1.056],[1.116,1.062],[1.113,1.078],[1.119,1.09],[1.101,1.105],[1.111,1.119],[1.134,1.12],[1.128,1.136],[1.14,1.145],[1.128,1.151],[1.119,1.166],[1.143,1.175],[1.146,1.194],[1.156,1.203],[1.134,1.221],[1.145,1.235],[1.163,1.232],[1.162,1.246],[1.174,1.258],[1.159,1.27],[1.153,1.289],[1.163,1.293],[1.169,1.287],[1.186,1.289],[1.18,1.295],[1.195,1.313],[1.183,1.325],[1.189,1.344],[1.186,1.353],[1.206,1.363],[1.212,1.36],[1.214,1.377],[1.229,1.389],[1.235,1.399],[1.232,1.405],[1.244,1.411],[1.241,1.42],[1.256,1.438],[1.263,1.478],[1.275,1.481],[1.281,1.5],[1.281,1.527],[1.275,1.539],[1.281,1.551],[1.275,1.579],[1.266,1.591],[1.269,1.597],[1.253,1.616],[1.256,1.622],[1.234,1.651],[1.226,1.652],[1.221,1.666],[1.209,1.669],[1.185,1.694],[1.133,1.715],[1.056,1.721],[0.965,1.694],[0.943,1.697],[0.922,1.688],[0.909,1.694],[0.879,1.678],[0.861,1.681],[0.848,1.675],[0.842,1.681],[0.809,1.663],[0.784,1.663],[0.775,1.654],[0.766,1.657],[0.711,1.636],[0.702,1.639],[0.695,1.632],[0.662,1.626],[0.656,1.617],[0.549,1.602],[0.512,1.587],[0.506,1.59],[0.488,1.581],[0.405,1.562],[0.347,1.535],[0.312,1.503],[0.29,1.472],[0.275,1.441],[0.275,1.432],[0.287,1.423],[0.283,1.418],[0.274,1.428],[0.266,1.42],[0.275,1.414],[0.263,1.408],[0.272,1.393],[0.26,1.389],[0.263,1.383],[0.254,1.368],[0.263,1.362],[0.251,1.359],[0.254,1.347],[0.248,1.341],[0.254,1.334],[0.238,1.313],[0.251,1.298],[0.242,1.292],[0.242,1.252],[0.235,1.246],[0.235,1.234],[0.245,1.224],[0.235,1.221],[0.245,1.206],[0.238,1.185],[0.251,1.16],[0.245,1.148],[0.257,1.117],[0.251,1.099],[0.263,1.096],[0.26,1.087],[0.269,1.072],[0.243,1.064],[0.235,1.056],[0.235,1.044],[0.255,1.018],[0.264,1.033],[0.281,1.029],[0.269,1.023],[0.267,1.012],[0.255,1.015],[0.238,1.004],[0.238,0.977],[0.269,0.968],[0.232,0.943],[0.238,0.916],[0.257,0.903],[0.252,0.887],[0.246,0.89],[0.232,0.882],[0.242,0.864],[0.238,0.854],[0.258,0.847],[0.274,0.868],[0.281,0.848],[0.281,0.836],[0.272,0.827],[0.281,0.818],[0.281,0.802],[0.275,0.796],[0.281,0.79],[0.278,0.772],[0.264,0.761],[0.255,0.77],[0.232,0.766],[0.238,0.76],[0.235,0.735],[0.255,0.718],[0.264,0.731],[0.274,0.734],[0.278,0.729],[0.271,0.7],[0.255,0.715],[0.232,0.705],[0.232,0.674],[0.254,0.656],[0.229,0.644],[0.235,0.631],[0.232,0.619],[0.257,0.592],[0.229,0.585],[0.229,0.561],[0.26,0.533],[0.252,0.526],[0.24,0.532],[0.229,0.527],[0.235,0.5],[0.229,0.494],[0.251,0.475],[0.243,0.468],[0.231,0.471],[0.226,0.466],[0.232,0.46],[0.229,0.433],[0.257,0.414],[0.248,0.411],[0.246,0.4],[0.237,0.416],[0.223,0.411],[0.22,0.399],[0.226,0.387],[0.22,0.374],[0.245,0.356],[0.243,0.345],[0.249,0.352],[0.254,0.344],[0.234,0.339],[0.225,0.361],[0.211,0.356],[0.214,0.335],[0.205,0.313],[0.191,0.309],[0.183,0.298],[0.183,0.274],[0.173,0.263],[0.157,0.263],[0.15,0.255],[0.153,0.231],[0.139,0.214],[0.127,0.226],[0.104,0.216],[0.107,0.191],[0.092,0.179],[0.084,0.156],[0.069,0.168],[0.061,0.167],[0.058,0.16],[0.073,0.148],[0.053,0.125],[0.044,0.138],[0.034,0.139],[0.035,0.156],[0.024,0.151],[0.028,0.142],[0.009,0.121],[0.015,0.115],[0.011,0.11]],"scaleRefs":["bcm-kag-mlok.length"],"inputs":{"bcm-kag-mlok.length":2.73},"tolerance":0.004,"photo":"references/bcm-kag-mlok 1693a668bba4 (BCM's BCM-KAG-MCMR-BLK-2: the KAG alone on white, its left side square on, its T-nuts up, 1499 x 1000)","method":"luminance < 128, inside [285, 225, 1205, 830], closing ×1, largest piece, holes filled; rotated +180.0° as declared; scale from bcm-kag-mlok.length = 2.73 in (x-extent 893 px → 327.1 px/in); origin at x min, y min of the outline; Douglas-Peucker at 0.004 in with the extremes kept: 328 points (IoU 0.996 with the full outline); checks: height 1.721 ± 0.021 in vs bcm-kag-mlok.height 1.684 ± 0.03 (corroborated): agrees (tools/trace.py)","via":"harvest","note":"BCM's own side view, scaled by the length read on the installed photo's slots. The ribs along the tail's underside and the deep end's front and back are in the outline as teeth; the T-nuts above the plate are left out."}},"gaps":[{"what":"Any size or weight from BCM or a seller","need":"BCM's page states none and its product data has \"weight\":null; a seller's table, a reviewer's calipers or scale, or a dimensioned drawing"},{"what":"The width, from a view square to the part's end or its face","need":"an end-on or straight-down photo with a scale (a rail, a slot, a tape lying on it); the width is read on a face-on photo taken a little from one side"},{"what":"How far the T-nuts reach inside the handguard (reach_inside)","need":"BCM's figure for its M-LOK nuts, or a side view of them tightened on a slot of known depth"},{"what":"The face's hollow's depth, the cups' depth, how far up the toe's bore the screw is, and the toe's slots","need":"a view into each with a scale, or a section"},{"what":"A design patent for the KAG","need":"The face's moulded PATENT marking names Magpul's M-LOK page (https://www.magpul.com/ip, BCM's FDE -4); a search lead, D745629, is tied to BCM or the KAG by no page on file"}]},"bcm-m4-upper":{"id":"bcm-m4-upper","name":"M4 Upper Receiver Assembly (w/ Laser T-Markings)","manufacturer":"BCM","sku":"BCM4-UR-M4","url":"https://bravocompanyusa.com/bcm-m4-upper-receiver-assembly-w-laser-t-markings/","category":"upper","description":"BCM's M4 flat-top upper receiver, \"Precision machined to correct Mil-Specs from 7075 T6 Forgings\" and sold \"Fully Assembled with forward assist, and ejection port cover\": a \"Mil-Std 1913 Rail\" of 13 slots with \"Laser etched T-markings\" (T2 to T12, in every other slot), \"Machined for use with barrels that use an M4 barrel extension\". No barrel, bolt carrier group or charging handle.","weight":"bcm-m4-upper.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"pins":{"origin":[0,0,0]},"front_face":{"origin":["{.front_face_x}","{.bore_axis_above_pin}",0],"note":"The end of the barrel-nut thread on the bore axis, +x toward the muzzle: a barrel extension's flange seats here, and a handguard is placed from here."},"rear_face":{"origin":["{.receiver_rear_x}","{.bore_axis_above_pin}",0],"note":"The rear face on the bore axis, +x toward the muzzle: the bolt carrier's channel opens here."},"handle_channel":{"origin":["{.handle_seat_x}","{.bore_axis_above_pin} + {.charging_handle_above_bore}",0],"note":"The charging handle's seat on its channel's axis, +x toward the muzzle: the front wall of the open notch under the rail's rear end, which the handle's shoulder stops against, at the notch's mid-height. (At the rear face until 2026-10-05: the handle hung 0.69 in behind where it belongs.)"},"top_rail":{"origin":["{.rail_slot0_x}","{.rail_top_above_pin}",0],"note":"The rail's top at its rearmost slot's centre, +x toward the muzzle (picatinny: index = slot number; slot n is the one BCM's marks call T(n + 1), the even ones being marked)."}},"interfaces":{"receiver_pins":{"type":"ar15.upper_lower","role":"upper","anchor":"pins","params":{"pin_spacing":"={std.ar15.pin_spacing}"},"flips":false},"barrel_extension":{"type":"ar15.barrel_extension","role":"receiver","anchor":"front_face","params":{},"flips":false,"note":"BCM: \"Machined for use with barrels that use an M4 barrel extension\"; \"Inside Diameter for barrel extension slightly undersized for a tighter fit to the barrel ... Please use a heat gun or hair dryer to warm up threaded bore of receiver if barrel extension is too tight.\""},"handguard_mount":{"type":"ar15.handguard_mount","role":"receiver","anchor":"front_face","params":{"nut":"standard"},"flips":false,"note":"BCM: \"Built to the correct Mil-Specs\". Its page names no barrel nut; the Army's drawing of the upper gives the nose's thread as 1.250-18 UNEF-2A (12576280, Detail C), the one a standard AR-15 barrel nut screws onto."},"carrier_channel":{"type":"ar15.carrier_channel","role":"receiver","anchor":"rear_face","params":{},"flips":false},"charging_handle_channel":{"type":"ar15.charging_handle_channel","role":"receiver","anchor":"handle_channel","params":{},"flips":false},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}","seam":"={.rail_front_x} - {.rail_slot0_x}","seam_parts":"the receiver's rail and the handguard's","seam_behind":"receiver","seam_ahead":"handguard"},"flips":false,"note":"BCM: \"Mil-Std 1913 Rail for mounting optics and accessories\". Its own rail of 13 slots; a handguard's rail ahead of it is the handguard's."}},"materials":{"receiver":{"label":"Receiver","finish":"anodized","recolorable":true,"color":"placeholder-black","note":"BCM: \"Hard Coat Anodized per Mil-A-8625F, Type III, Class2\"; sold in black only (Primary Arms: \"Color Black\"). Recolorable for planning a colour scheme."},"hardware":{"label":"Forward assist and port cover","finish":"phosphate","recolorable":false,"color":"steel-phosphate-charcoal","note":"The forward assist's cap and the ejection port cover with its hinge pin: steel by the Army's drawings (9349084, 8448785). BCM states no finish for them (of the forward assist only \"heat treated tool steel pawl, with press fit and pinned cap\"); its photos show the cover a matte charcoal grey with rub marks, as a phosphate is, where the receiver beside it is black (#59595b and #565555 on the cover in two of BCM's photos, #2f2f32 and #3c3b3c on the receiver): phosphate by its look, in the catalog's charcoal phosphate. Bright in those photos and not drawn: the cover's spring and its latch's plunger."}},"components":{},"geometry":{"components":{"receiver":"bcm-m4-upper.receiver.glb"},"approximations":["Its side outline (Primary Arms' right view, pin-framed) across the mil-spec flat top's section: the rail's lower faces under its slots' floors the standard's (MIL-STD-1913's, since 2026-10-12: the reference CAD set's model has them a hundredth further out, at the standard's stated .164, and every clamp stood in them), the height of its dovetail's foot, its neck and the flat sides from the reference CAD set's model of a mil-spec forging, the round body at the Army drawing's forged 1.19, the lugs at the drawing's width. The photo is taken from above and near, so the outline's ends are cut at the drawing's two faces and its underside is set on the deck's height; its rear end's steps and the lugs' outlines are as the photo reads them (0.02 to 0.04 in low at the notch under the rail). The reference model's step at the neck's foot, a ledge .010 wide where the neck meets the flat side a hundredth further out, isn't drawn (2026-10-12): at the size the page draws a rifle it is a third of a pixel, and it drew as a dashed hairline along the body; the neck's wall leans from its width under the dovetail's foot out to the side's face at the height of the step.","Its rear lower corner (2026-10-12): out where a lower's two rear walls stand, the arc they rise along (the Army's .750 R, drawing 8448608 sheet 1; the upper's own drawing has .760, a hundredth clear of them, which isn't drawn: it would be a slit across the rifle); between the walls, what the side outline has there, which hangs in the trough.","The barrel-nut thread is the drawing's 1.250-18: its major and minor diameters as rings 1/18 in apart (not a helix), with the index pin's notch; the thread's relief at the shoulder and the chamfer at its mouth aren't drawn.","The ejection port is cut where the M16A2's drawing puts it and its cover is drawn closed over it, as BCM's photos show the part: a flat sheet at the drawing's length, height and thickness on the port's 22.5° face, hinged where the reference model has the pin, with its two beads as raised U-shaped loops set out as the cover's drawing has them (square in section, as wide as twice the pressed radius and the sheet) and its latch housing as a square boss as wide as the photo shows it, standing as far off the sheet as the beads (its own height isn't sourced). The hinge is one curl the cover's length (its two knuckles and the spring between them aren't told apart) on a plain pin between the ends the photo shows; the pin's retaining ring isn't drawn. The cover's seat is a flat cut the port's length; the hinge lugs are plain cylinders on a web.","The forward assist's housing is a cylinder about the drawing's axis (20° in plan from the bore's mouth, 1.0285 off the middle) at the radius BCM's banner shows from above, run forward until it sinks into the body, with a web of 0.6 of its radius either side of the axis between it and the body; the forging's own blends above and below it aren't sourced. Its cap is the drawing's (head, body and 20° flare, the rings on its face left out) standing out as far as the banner shows it at rest; the plunger, pawl and spring inside aren't drawn.","The deflector is a wedge through six points: its two feet on the body, its foot and top there, and the ridge the photos give (its reach from above, its height from the side); its faces are flat and its edges broken.","Behind its rail's head the rail is the standard's tongue (2026-10-20, lib.rail_tongue: the reference model's, ±0.318 with a round end, its rearmost point where this receiver's photo has the rail's end, and two concave rounds out to the head's width by 0.4165 ahead of the pin, where the app's head begins): until then the head was drawn at its full width to the rail's end, square, and every charging handle's T stood in its two corners. The charging handle's channel is the standard's (lib.handle_channel: the Army drawing's tier and roof, 8448524 sheet 2, and the reference model's widths and its two upright rounds), and so is the notch the handle's block lies in at least (lib.handle_notch: the reference model's floor, roof and 45 degree corners); a handle rides on its guide lugs on the tier (std.ar15.charging_handle_axis_y), 0.044 under where BCM's photo of the see-through notch put it, where every handle's top stood in the roof and its lugs in the walls of the plain slot this receiver had until 2026-10-20. The open notch under the rail's rear end, where a handle's T lies, has the channel's roof across the receiver (the traced outline has the rail's underside there by its near edge, 0.03 lower: a handle stood in it). The channel's the gas tube's back bore, the cam pin's pocket inside the left wall, the M4 feed ramp cuts, the openings in the underside, the takedown lug's hole's countersink and the markings (the T-marks, BCM4 over the gas tube's hole, the forge mark) aren't drawn. The gas tube's hole has its four lobes on the diagonals, where the reference model has them (the drawing leaves their turn free). The lugs' pin holes are through at the drawing's size.","On the left (2026-10-05), the cam pin's pad is the left photo's outline of its foot, brought back through that photo's lens at a depth midway between the wall and the pad's face, out to the reference model's face, with one round all the way round its face as wide as the photo has the face's bright edge inside the foot: the real pad's top runs up into the rail's foot on a slope, and its forge mark isn't drawn. The charging handle latch's slot is a pocket in the wall's outer face, down to the .045 of wall the Army's drawing leaves over the channel, where that drawing puts it from the notch's front wall (.156 of wall, .195 of slot, full rounds) and between the heights the photo has it; the photo has the slot 0.01 further forward, as it has that wall. Its upper end runs up behind the rail the app draws as a bar. The shallow step the drawing has at the notch's front, beside the slot, and the raised band low on the left side aren't drawn.","Along the foot of the left wall (2026-10-13), a raised band from the pivot lug's rear edge back past the magazine well (x 6.105 to 2.975 ahead of the takedown pin, from the deck up to 0.601), its rear end leaning back to a foot on the lug wall at 2.895, and on it under the cam pin's pad a low tab (x 3.962 to 4.57, its face up to 0.316, its upper face leaning back to the band at 0.368): all read on Primary Arms' left view through its lens. How far either stands out is in no view on file and no depth is in the ledger. ASSUMED: the band's face is upright and stands where the body as drawn is at the height of its upper edge (0.527 off the middle, 0.074 out from the lug wall: its rear end then leans 43 degrees, and its underside reads a pixel low in the photo, as a face that much nearer the lens would); the tab's rear end is taken to lean as the band's does, which puts its face 0.059 off the band's; the tab's front end is drawn square (the photo has a soft beginning there) and the lit line along its lower edge isn't drawn. The body's section under the bore is still the reference model's round: the photo has the crease where it meets the lug wall at 0.42 above the pin line behind the band, for the 0.49 drawn."],"ledger":["bcm-m4-upper.receiver_rear_x","bcm-m4-upper.front_face_x","bcm-m4-upper.underside_y","bcm-m4-upper.rail_top_above_pin","bcm-m4-upper.bore_axis_above_pin"]},"profiles":{"side":{"plane":"xy","origin":"the takedown pin centre (the rifle frame origin), +x toward the muzzle","offset":{},"points":[[-0.621,1.55],[-0.621,0.51],[-0.598,0.51],[-0.559,0.455],[-0.489,0.463],[-0.493,0.436],[-0.41,0.362],[-0.242,0.265],[-0.233,-0.213],[-0.213,-0.24],[-0.12,-0.247],[0.217,-0.247],[0.228,-0.235],[0.22,0.18],[0.247,0.191],[2.773,0.197],[2.836,0.181],[6.191,0.197],[6.204,-0.12],[6.294,-0.21],[6.349,-0.225],[6.458,-0.225],[6.552,-0.186],[6.61,-0.119],[6.626,-0.025],[6.625,0.201],[6.657,0.217],[6.66,0.292],[6.676,0.299],[6.707,0.268],[6.739,0.284],[6.754,0.26],[6.785,0.284],[6.817,0.261],[6.848,0.284],[6.872,0.261],[6.895,0.284],[6.918,0.269],[6.958,0.284],[6.989,0.269],[7.012,0.292],[7.036,0.293],[7.036,1.455],[6.994,1.497],[6.978,1.481],[6.939,1.497],[6.916,1.481],[6.892,1.497],[6.861,1.481],[6.83,1.496],[6.814,1.481],[6.775,1.496],[6.759,1.481],[6.72,1.496],[6.681,1.465],[6.654,1.469],[6.653,1.867],[6.668,1.914],[6.668,2.024],[6.66,2.055],[6.633,2.075],[6.218,2.074],[6.207,2.062],[6.211,2.003],[6.195,2.042],[6.156,2.035],[6.136,1.999],[6.148,1.98],[6.125,1.988],[6.109,1.948],[6.062,1.948],[6.011,1.952],[6.003,2.046],[5.984,2.073],[5.819,2.073],[5.808,2.061],[5.816,2.006],[5.8,2.006],[5.788,2.042],[5.765,2.042],[5.753,1.998],[5.777,1.975],[5.741,1.987],[5.695,1.979],[5.695,1.963],[5.73,1.951],[5.695,1.947],[5.612,1.951],[5.604,2.045],[5.585,2.072],[5.421,2.072],[5.409,2.06],[5.417,2.013],[5.366,2.002],[5.378,1.982],[5.366,1.97],[5.35,1.986],[5.327,1.947],[5.241,1.946],[5.214,1.958],[5.194,2.072],[5.014,2.071],[5.018,2.044],[4.99,2.048],[4.987,2.028],[5.014,2.032],[5.018,2.005],[4.979,1.997],[4.983,1.969],[4.959,1.985],[4.944,1.969],[4.893,1.973],[4.944,1.961],[4.936,1.946],[4.819,1.946],[4.795,2.071],[4.623,2.07],[4.611,2.059],[4.619,2.004],[4.588,1.996],[4.592,1.969],[4.568,1.976],[4.553,1.945],[4.428,1.945],[4.408,1.964],[4.396,2.07],[4.232,2.077],[4.212,2.065],[4.22,2.003],[4.189,1.995],[4.212,1.972],[4.209,1.952],[4.169,1.975],[4.162,1.944],[4.021,1.944],[3.997,2.069],[3.825,2.076],[3.813,2.002],[3.798,1.994],[3.81,1.951],[3.778,1.967],[3.755,1.943],[3.685,1.943],[3.61,1.955],[3.598,2.068],[3.426,2.075],[3.415,2.001],[3.399,1.985],[3.415,1.954],[3.387,1.966],[3.34,1.942],[3.215,1.95],[3.192,2.075],[3.027,2.075],[3.016,2],[3,1.992],[3.008,1.953],[2.934,1.941],[2.816,1.949],[2.805,1.961],[2.804,2.062],[2.785,2.074],[2.621,2.074],[2.597,1.948],[2.41,1.948],[2.386,2.073],[2.23,2.073],[2.21,2.061],[2.21,1.959],[2.198,1.948],[2.011,1.947],[1.999,1.959],[1.999,2.061],[1.987,2.072],[1.909,2.072],[1.811,2.068],[1.811,1.998],[1.792,1.947],[1.604,1.946],[1.6,2.06],[1.588,2.071],[1.455,2.071],[1.404,2.059],[1.401,1.993],[1.244,1.992],[1.205,1.945],[1.193,1.957],[1.189,2.071],[-0.492,2.067],[-0.602,2.082],[-0.601,1.902],[-0.5,1.871],[-0.023,1.872],[0.068,1.775],[0.068,1.657],[0.017,1.599],[-0.609,1.597],[-0.62,1.585],[-0.616,1.558],[-0.581,1.554]],"scaleRefs":["std.ar15.pin_spacing"],"inputs":{"bcm-m4-upper.front_face_x":7.036,"bcm-m4-upper.receiver_rear_x":-0.621,"std.ar15.pin_spacing":6.375},"tolerance":0.01,"photo":"references/bcm-m4-upper b896edc62dc6 (Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768)","method":"luminance < 200, largest piece, holes filled; frame from the reviewed holes takedown, pivot (127.9 px/in, rms 0.000 in over 2 points); origin at the photo's frame; clipped to x min {.receiver_rear_x} = -0.621, x max {.front_face_x} = 7.036; Douglas-Peucker at 0.01 in with the extremes kept: 200 points (IoU 0.997 with the full outline); the lens stood about 38 in away, 4 to 5 in above the pin line over x 2.2 (the far rims' offsets in the two lug holes): the underside's near edge reads 0.19 for the deck's 0.25 and the tooth tops 2.07 for 2.09, and the forward assist's cap behind the rear face is cut off with the rear end; checks: y_max 2.082 ± 0.012 in vs bcm-m4-upper.rail_top_above_pin 2.09 ± 0.02 (corroborated): agrees; y_min -0.247 ± 0.012 (tools/trace.py)","via":"harvest","note":"Its outer silhouette with the lug holes filled, cut at the drawing's rear face and front face: the barrel nut's thread at its front, the port cover, the forward assist's housing and the deflector inside it. Read from above and near: its underside stands 0.06 low and is set on the deck's height where it is built."},"left":{"plane":"xy","origin":"the takedown pin centre (the rifle frame origin), +x toward the muzzle; the left side seen mirrored","offset":{},"points":[[-0.892,1.026],[-0.885,0.837],[-0.841,0.736],[-0.772,0.681],[-0.677,0.689],[-0.608,0.562],[-0.474,0.413],[-0.252,0.272],[-0.237,-0.186],[-0.219,-0.226],[-0.117,-0.233],[0.213,-0.229],[0.206,-0.091],[0.224,-0.116],[0.228,-0.076],[0.257,-0.084],[0.242,-0.011],[0.256,-0.011],[0.256,0.2],[0.267,0.211],[0.739,0.211],[3.913,0.193],[6.171,0.21],[6.175,-0.091],[6.204,-0.149],[6.288,-0.218],[6.331,-0.232],[6.447,-0.232],[6.556,-0.181],[6.611,-0.105],[6.618,0.207],[6.643,0.291],[6.672,0.291],[6.701,0.262],[6.73,0.284],[6.752,0.255],[6.781,0.284],[6.817,0.255],[6.839,0.284],[6.861,0.255],[6.897,0.284],[6.919,0.255],[6.955,0.284],[6.984,0.255],[7.06,0.317],[7.096,0.513],[7.111,0.84],[7.096,1.246],[7.059,1.442],[7.004,1.497],[6.975,1.475],[6.954,1.504],[6.939,1.504],[6.925,1.475],[6.888,1.504],[6.867,1.467],[6.837,1.504],[6.808,1.467],[6.787,1.504],[6.75,1.467],[6.729,1.504],[6.7,1.467],[6.631,1.471],[6.637,2.059],[6.619,2.092],[6.161,2.091],[6.172,2.08],[6.136,2.058],[6.129,2.037],[6.143,2.022],[6.103,1.989],[5.973,1.996],[5.951,2.091],[5.769,2.091],[5.766,2.029],[5.751,2.043],[5.74,1.989],[5.595,1.989],[5.562,2],[5.562,2.065],[5.544,2.09],[5.363,2.09],[5.366,2.007],[5.348,1.996],[5.167,1.995],[5.145,2.09],[4.978,2.097],[4.952,2.057],[4.967,2.05],[4.967,1.999],[4.945,1.992],[4.963,1.966],[4.949,1.966],[4.934,1.995],[4.76,1.995],[4.756,2.071],[4.738,2.089],[4.571,2.096],[4.557,1.966],[4.535,1.995],[4.528,1.966],[4.52,1.995],[4.361,1.995],[4.357,2.063],[4.339,2.089],[4.172,2.089],[4.157,1.965],[4.15,1.987],[4.099,1.987],[3.969,1.987],[3.961,1.965],[3.939,2.096],[3.765,2.081],[3.751,1.965],[3.725,1.968],[3.747,1.976],[3.743,1.987],[3.591,1.994],[3.569,1.986],[3.562,1.965],[3.54,2.088],[3.366,2.08],[3.351,1.986],[3.17,1.986],[3.162,1.971],[3.151,2.077],[3.126,2.087],[2.966,2.08],[2.963,1.996],[2.908,1.978],[2.785,1.985],[2.778,2],[2.77,1.978],[2.752,1.996],[2.748,2.08],[2.567,2.08],[2.556,1.981],[2.48,1.978],[2.356,1.992],[2.349,2.079],[2.175,2.079],[2.153,1.977],[2.051,1.977],[2.008,1.977],[1.975,1.995],[1.971,2.013],[1.953,1.995],[1.95,2.079],[1.768,2.079],[1.754,1.984],[1.645,1.977],[1.598,2.002],[1.587,2.064],[1.554,2.06],[1.572,2.086],[1.376,2.078],[1.347,1.955],[1.329,1.958],[1.333,1.976],[1.224,1.984],[1.198,2.06],[1.162,2.06],[1.173,2.085],[-0.599,2.076],[-0.603,1.905],[-0.592,1.894],[-0.505,1.873],[-0.04,1.873],[0.058,1.782],[0.051,1.652],[-0.01,1.59],[-0.591,1.589],[-0.599,1.56],[-0.671,1.553],[-0.711,1.259],[-0.765,1.248],[-0.827,1.2],[-0.863,1.135]],"features":{"cam_pin_pad":[[[4.684,1.646],[4.646,1.641],[4.612,1.627],[4.582,1.603],[4.559,1.574],[4.544,1.539],[4.539,1.501],[4.54,1.178],[4.543,1.152],[4.553,1.127],[4.569,1.106],[4.59,1.09],[4.615,1.08],[4.641,1.076],[5.556,1.077],[5.582,1.081],[5.607,1.091],[5.628,1.107],[5.644,1.128],[5.654,1.153],[5.658,1.179],[5.657,1.502],[5.652,1.54],[5.638,1.575],[5.614,1.605],[5.585,1.628],[5.55,1.642],[5.512,1.647]]],"latch_slot":[[[0.4,1.813],[0.386,1.863],[0.349,1.9],[0.299,1.913],[0.248,1.9],[0.211,1.863],[0.198,1.812],[0.198,1.611],[0.212,1.56],[0.248,1.524],[0.299,1.51],[0.349,1.524],[0.386,1.561],[0.4,1.611]]]},"scaleRefs":["std.ar15.pin_spacing"],"inputs":{"std.ar15.pin_spacing":6.375},"tolerance":0.01,"photo":"references/bcm-m4-upper b3b8d1ad9d16 (Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768)","method":"luminance < 200, largest piece, holes filled; frame from the reviewed holes takedown, pivot (137.7 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.01 in with the extremes kept: 178 points (IoU 0.995 with the full outline); checks: y_max 2.097 ± 0.011 in vs bcm-m4-upper.rail_top_above_pin 2.09 ± 0.02 (corroborated): agrees; features through the same placement (cam_pin_pad: the raised pad over the cam pin's travel: the foot of its rounded edge; latch_slot: the charging handle latch's slot in the left wall, the obround pocket: its rim) (tools/trace.py)","via":"harvest","note":"The left side's silhouette, lug holes filled, as the photo has it (the forward assist's cap behind the rear face included): used for this side's two features only."}},"gaps":[{"what":"Its weight: two sellers' figures 1.4 oz apart, neither said to be the part's","need":"BCM's own figure, or a reviewer's on a scale"},{"what":"A view square to its rear or front end","need":"An end view with the rail in frame: its section is the reference model's of a mil-spec forging, checked on BCM's part only from above (the body's width, the rail's flat top)"},{"what":"How far the port cover's latch housing stands off the cover","need":"The Army's drawing of the housing (8448784), read"},{"what":"How far the raised band along the foot of the left wall and the tab on it stand out, and the body's section under the bore on BCM's own part","need":"A view along the receiver from its front or rear end, or from below, with the left wall's foot in profile: the band is drawn where the round body of the reference model is at its upper edge (0.074 out from the lug wall) and the tab by the lean of the band's rear end (0.059 more), both from one left view"}]},"bcm-mcmr-10-handguard":{"id":"bcm-mcmr-10-handguard","name":"MCMR-10 (M-LOK® Compatible* Modular Rail)","manufacturer":"BCM","sku":"BCM-MCMR-10-556-BLK","url":"https://bravocompanyusa.com/bcm-mcmr-10-m-lok-compatible-modular-rail/","category":"handguard","description":"Bravo Company's free-float M-LOK handguard in its 10 in length, 10.5 in to the tips of its flare (\"Actual length when measured to flare is 10.5\"\"): \"Precision Machined Aerospace 6061-T6 Aluminum Alloy\", \"Hard Coat Anodized per Mil-A-8625F, Type III, Class 2\", \"mounting interfaces on seven sides in addition to the baked in MIL-STD-1913 at the 12 O'Clock position\" (BCM, of the MCMR), clamped at 12 o'clock on its own steel barrel nut by two cross bolts (US Patent 8904691): \"Featuring the same industry leading barrel nut and lock up design as originally introduced on BCM's evolutionary KMR\". \"Designed to be used with pistol length, carbine length, or mid length gas systems; all with a low profile gas block.\" The asterisk in its name is BCM's: \"*M-LOK® is a registered trademark of Magpul Industries Corp.\"","weight":"bcm-mcmr-10-handguard.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"mount":{"origin":[0,0,0],"note":"The receiver's front face on the bore axis, +x toward the muzzle."},"mlok":{"origin":["{.mlok_side_slot0_x}",0,0],"note":"On the handguard's axis (the bore's: an octagon about it) at the side faces' rearmost M-LOK slot's centre (index 0), +x toward the muzzle; the faces are angles about this axis (M10)."},"mlok_between":{"origin":["{.mlok_diag_slot0_x}",0,0],"note":"The same axis at the rearmost slot's centre of the four faces between the sides and the top and bottom: their rows sit one rail pitch (10 mm) behind the side faces'."},"mlok_bottom":{"origin":["{.mlok_bottom_slot0_x}",0,0],"note":"The same axis at the underside's rearmost M-LOK slot's centre (index 0): its row in line with the side faces' (the family's reading, at its front end), with as many slots (assumed)."},"top_rail":{"origin":["{.rail_slot0_x}","{.rail_top_above_bore}",0],"note":"The rail's top at its rearmost slot's centre (the one marked T14), +x toward the muzzle (picatinny: index = slot number). Its own rail: the receiver's is the receiver's."}},"interfaces":{"handguard_mount":{"type":"ar15.handguard_mount","role":"handguard","anchor":"mount","params":{"nut":"standard"},"flips":false,"note":"BCM's installation manual: \"KMR series handguards (KMR, MCMR, QRF) are a free-floated design which mounts and aligns to the upper-receiver threads using a custom barrel nut\"; \"compatible ONLY with Mil-Spec direct impingement AR-15 platforms chambered in .223 Remington and/or 5.56x45mm NATO\". Its own barrel nut for the standard thread (BCM's page for this length: \"Steel Barrel Nut (same KMR, MCMR, and QRF series)\"); \"A minimum gap of .005\" should exist to maintain the free-float of the barrel. Note: The gap should not exceed .040\"\" (rear_x)."},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}","beyond_seam":true,"seam_behind":"receiver","seam_ahead":"handguard"},"flips":false},"mlok":{"type":"mlok","role":"slots","anchor":"mlok","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_side_slots}","interval":"={std.mlok.interval}","face_distance":"={.width} / 2","bore":"={.inside_diameter}","reach_inside":"={.reach_inside}"},"faces":{"right":{"angle":90,"note":"the rifle's right side (+z)"},"left":{"angle":-90}},"flips":false,"note":"The side faces. How far an accessory's nuts may reach inside depends on the barrel and gas block under it, other parts: reach_inside has no figure, so that check reads as unmade."},"mlok_between":{"type":"mlok","role":"slots","anchor":"mlok_between","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_diag_slots}","interval":"={std.mlok.interval}","face_distance":"={.width} / 2","bore":"={.inside_diameter}","reach_inside":"={.reach_inside}"},"faces":{"right_upper":{"angle":45,"note":"between the rail and the right side (1:30)"},"right_lower":{"angle":135},"left_lower":{"angle":-135},"left_upper":{"angle":-45}},"flips":false,"note":"The four faces between. The angles are a regular octagon's (BCM's own diagram of the MCMR's section draws one; this length's lower slope, seen from 18.5° above, runs the 39 px a face at 45° makes it), not measurements."},"mlok_bottom":{"type":"mlok","role":"slots","anchor":"mlok_bottom","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_bottom_slots}","interval":"={std.mlok.interval}","face_distance":"={.width} / 2","bore":"={.inside_diameter}","reach_inside":"={.reach_inside}"},"faces":{"bottom":{"angle":180,"note":"the underside (6 o'clock)"}},"flips":false,"note":"The underside, where BCM pictures its own Vertical Grip Mod 3 and KAG fitted (BCM-VG-MCMR-MOD-3-BLK-6, BCM-KAG-MCMR-BLK-5). No view looks at it square: its row's place is the family's reading, on the KAG's photo of an MCMR of a length it doesn't show, in line with the side faces' foremost slot (mlok_bottom_front_from_side_front), and its count is the side faces' (mlok_bottom_slots, assumed: where it ends at the rear is on no photo)."}},"materials":{"body":{"label":"Handguard","finish":"anodized","recolorable":true,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized","color":"placeholder-black","sku":"BCM-MCMR-10-556-BLK","source":"https://bravocompanyusa.com/bcm-mcmr-10-m-lok-compatible-modular-rail/"},"fde":{"label":"Flat Dark Earth","finish":"cerakote","color":"bcm-fde-cerakote","sku":"BCM-MCMR-10-556-FDE","source":"https://bravocompanyusa.com/bcm-mcmr-10-m-lok-compatible-modular-rail-flat-dark-earth/"}},"default":"black","note":"\"Hard Coat Anodized per Mil-A-8625F, Type III, Class 2\" (BCM's page for this length), and \"Flat Dark Earth Cerakote (LIMITED QTYS)\" as BCM-MCMR-10-556-FDE (its page for that one; Primary Arms: \"Color Flat Dark Earth Finish Cerakote\"): the grey-brown of the MCMR-15's, the same series of BCM's photographs (this length's side face between its rows of slots reads #827971 on MCMR_10_FDE, 85d879b8ed8e, region [560,676,1500,700], where the same reading of the 15's photo, 3c44f96c9c21, is #79736e: one colour within the two exposures). In both, what comes with it is black (BCM's photo of the Flat Dark Earth one with its hardware, 9e7eeb994846: the steel barrel nut, the lock block and its two cross bolts, the sling mount, a rail section; BCM's of the black one, 5336b2e8ad26): the barrel nut is inside it, the sling mount and the rail section are accessories in the box, and the two cross bolts are the slot `bolts`. Its marks (BCM's and Magpul's, the T-numbers) are white on both and aren't drawn."},"bolts":{"label":"Cross bolts","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The two cross bolts of its clamp, in their holes under the rail's rear: black on the black handguard and on the Flat Dark Earth one (BCM's photo of the Flat Dark Earth MCMR-10 laid out with its hardware, 9e7eeb994846: two black socket screws in a black block). Steel; their finish isn't stated, and a black on steel isn't fitted to a photo."}},"components":{},"geometry":{"model":"bcm-mcmr-10-handguard.glb","components":{},"approximations":["Its section is the MCMR-15's (the family's, by BCM's own 1.5 in width and 1.3 in inside diameter on this length's page): a regular octagon across the 1.5 in, about the bore, with a neck up to the rail; no view shows it square on. The neck's width is where a 45° face reaches the height the 15's level photo shows it ending, and the corners are sharp but for a 0.012 in break (the photos show them a little rounded).","Its length is BCM's 10.5 in to the tips of the flare. The muzzle end is this length's own, cut from four figures read on BCM's photo of it from 18.5° above and brought back to a side view (no level photo of it alone is on file): the rail's front end and a square face under it down to 0.63 in above the bore, a slope from there to the flat tips of the side faces (their full width, 0.31 above to 0.28 below the bore), and a slope back from the tips to the bottom flat 0.36 in behind them, each square across. By BCM's length and the rail's place the tips come out 0.16 in ahead of the rail's front end; the photos have them 0.10 ahead (the 15's are 0.32): the difference is inside what BCM's one decimal and the gap at the receiver allow, and the upper slope is drawn 5° shallower for it.","The rail's 25 slots are the standard's, placed where the first reads on the complete upper's photos; its head is the standard's in section (MIL-STD-1913's Figure 1: lib.rail_head), its lower faces carried on to the neck's walls, as the 15 in rail's is since 2026-10-12.","Inside it is BCM's 1.3 in: a round bore from the rear end to the first M-LOK slot (how far the round part really runs isn't seen), then 1.3 in across inner flats that follow the outside, as Rifle Supply's photo of this length's muzzle end shows them. The neck is hollow by the same 0.1 in wall from end to end (light shows through its holes from side to side), and the room between its two walls is open down into the bore all the way back: BCM's photo of this length's rear end (f7405f8a8d30) looks in between the two walls from behind, down into the bore and out through the far wall's slot. That is where its clamp closes at 12 o'clock and where a gas tube runs back over the barrel nut to the receiver. The room's width (the neck's less a wall each side, 0.50 in) and its top (a wall's thickness under the rail's body, 0.885 in above the bore) aren't measured: a .180 in tube at the standard's 0.78 in above the bore has 0.015 in over it and the cross bolts just under it.","Five M-LOK slots on each of six faces at the standard's size and pitch, the side faces' rows one rail pitch ahead of the others'; eleven slanted and eleven round holes a side under the rail, at this length's own count and place and at the 15's sizes, cut straight through from side to side; the two cross-bolt holes where this length's photo has them.","The underside's M-LOK row, at the standard's size and pitch, in line with the side faces' rows: no view looks at an MCMR's underside square, and BCM's photo of its KAG fitted there (the family's reading, on an MCMR of a length it doesn't show) shows the bottom face nearly edge-on, its two foremost slots dark in it, the foremost in line with the side faces' foremost (within 0.03 in) and one rail pitch ahead of the 4:30 face's. As many slots as a side face, assumed: the row's rear end shows on no photo. On this length the foremost ends 0.058 in short of the bottom flat's end, where the photo has an MCMR's end at it.","The two slots across its rear end under the rail (where its clamp is split and its index plate sits) are cut as the MCMR-15's level outline shows them, straight across: the clamp end is the family's (\"the same industry leading barrel nut and lock up design\"), and this length's photos, all from above, show the same two slots without giving their heights.","The two cross bolts are each a plain round pin a fiftieth narrower than its hole shows, from one upper face to the other across the room between the neck's walls, its ends just under the faces: their heads, and which side they go in from, are on no photo (BCM pictures the handguard off a rifle, its holes empty). They are their own material, black in both colours of handguard.","Not drawn: the teeth under the rail's rear end, the rear end's turned ring and the flats' run-out into it, the relief under each cross-bolt hole, the laser marks (T14 to T38 in the rail's slots, BCM's and Magpul's on the sides), and its mounting hardware (barrel nut, clamp blocks, index plate: inside it or at the seam).","Its metal by the model is 5.16 cubic inches, which at aluminium's density is 8.1 oz against BCM's 6.6 oz for the handguard alone: the real walls, neck and rail are lighter than a 0.1 in wall everywhere and a solid rail make them (the 15's model is over by about as much)."],"ledger":["bcm-mcmr-10-handguard.length","bcm-mcmr-10-handguard.width","bcm-mcmr-10-handguard.height","bcm-mcmr-10-handguard.inside_diameter","bcm-mcmr-10-handguard.rear_x"]},"profiles":{},"gaps":[{"what":"A level side photo of this length alone (its muzzle end's two slopes are read on a photo from 18.5° above, each ± 0.03 to 0.06 in; the heights of the two slots across its rear end are the 15's)","need":"Primary Arms' gallery for BCM-MCMR-10-556-BLK (script-loaded: not fetched), whose first picture of the 15 is the level one; or any seller's straight side view"},{"what":"The underside's M-LOK row seen square: how many slots it has and where it begins at the rear (the row is the family's reading at its front end, on BCM's photo of its KAG fitted under an MCMR, with the bottom face nearly edge-on; its count is the side faces', assumed)","need":"A photo of this length from below, its whole underside in frame; a seller's gallery or a review may have one"},{"what":"The room inside its faces before the barrel (reach_inside: what an M-LOK accessory's nuts may take)","need":"The barrel's and the gas block's size under it, from the parts a build puts there"},{"what":"Its section square on (the neck's width, the room between its walls and how high it goes under the rail, the corners' rounding, the rail's dovetail)","need":"An end view with a known size in frame (the views of its rear end on file are three-quarter ones); BCM's diagram of the MCMR's section is undimensioned"},{"what":"Its two cross bolts' heads (each bolt is drawn as a plain pin as wide as its hole shows)","need":"a photo of an MCMR installed, from each side, close on the clamp"}]},"bcm-mcmr-13-handguard":{"id":"bcm-mcmr-13-handguard","name":"MCMR-13 (M-LOK® Compatible* Modular Rail)","manufacturer":"BCM","sku":"BCM-MCMR-13-556-BLK","url":"https://bravocompanyusa.com/bcm-mcmr-13-m-lok-compatible-modular-rail/","category":"handguard","description":"Bravo Company's free-float M-LOK handguard in its 13 in length, 13.4 in to the tips of its flare (\"Actual length when measured to flare is 13.4\"\"): \"Precision Machined Aerospace 6061-T6 Aluminum Alloy\", \"Hard Coat Anodized per Mil-A-8625F, Type III, Class 2\", \"mounting interfaces on seven sides in addition to the baked in MIL-STD-1913 at the 12 O'Clock position\" (BCM, of the MCMR), clamped at 12 o'clock on its own steel barrel nut by two cross bolts (US Patent 8904691): \"Featuring the same industry leading barrel nut and lock up design as originally introduced on BCM's evolutionary KMR\". \"Designed to be used with pistol length, carbine length, mid length, or Mil-Spec M16 rifle length gas systems; all with a low profile gas block.\" The asterisk in its name is BCM's: \"*M-LOK® is a registered trademark of Magpul Industries Corp.\"","weight":"bcm-mcmr-13-handguard.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"mount":{"origin":[0,0,0],"note":"The receiver's front face on the bore axis, +x toward the muzzle."},"mlok":{"origin":["{.mlok_side_slot0_x}",0,0],"note":"On the handguard's axis (the bore's: an octagon about it) at the side faces' rearmost M-LOK slot's centre (index 0), +x toward the muzzle; the faces are angles about this axis (M10)."},"mlok_between":{"origin":["{.mlok_diag_slot0_x}",0,0],"note":"The same axis at the rearmost slot's centre of the four faces between the sides and the top and bottom: their rows sit one rail pitch (10 mm) behind the side faces'."},"mlok_bottom":{"origin":["{.mlok_bottom_slot0_x}",0,0],"note":"The same axis at the underside's rearmost M-LOK slot's centre (index 0): its row in line with the side faces' (the family's reading, at its front end), with as many slots (assumed)."},"top_rail":{"origin":["{.rail_slot0_x}","{.rail_top_above_bore}",0],"note":"The rail's top at its rearmost slot's centre (the one marked T14), +x toward the muzzle (picatinny: index = slot number). Its own rail: the receiver's is the receiver's."}},"interfaces":{"handguard_mount":{"type":"ar15.handguard_mount","role":"handguard","anchor":"mount","params":{"nut":"standard"},"flips":false,"note":"BCM's installation manual: \"KMR series handguards (KMR, MCMR, QRF) are a free-floated design which mounts and aligns to the upper-receiver threads using a custom barrel nut\"; \"compatible ONLY with Mil-Spec direct impingement AR-15 platforms chambered in .223 Remington and/or 5.56x45mm NATO\". Its own barrel nut for the standard thread (BCM's page for this length: \"Steel Barrel Nut (same KMR, MCMR, and QRF series)\"); \"A minimum gap of .005\" should exist to maintain the free-float of the barrel. Note: The gap should not exceed .040\"\" (rear_x)."},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}","beyond_seam":true,"seam_behind":"receiver","seam_ahead":"handguard"},"flips":false},"mlok":{"type":"mlok","role":"slots","anchor":"mlok","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_side_slots}","interval":"={std.mlok.interval}","face_distance":"={.width} / 2","bore":"={.inside_diameter}","reach_inside":"={.reach_inside}"},"faces":{"right":{"angle":90,"note":"the rifle's right side (+z)"},"left":{"angle":-90}},"flips":false,"note":"The side faces. How far an accessory's nuts may reach inside depends on the barrel and gas block under it, other parts: reach_inside has no figure, so that check reads as unmade."},"mlok_between":{"type":"mlok","role":"slots","anchor":"mlok_between","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_diag_slots}","interval":"={std.mlok.interval}","face_distance":"={.width} / 2","bore":"={.inside_diameter}","reach_inside":"={.reach_inside}"},"faces":{"right_upper":{"angle":45,"note":"between the rail and the right side (1:30)"},"right_lower":{"angle":135},"left_lower":{"angle":-135},"left_upper":{"angle":-45}},"flips":false,"note":"The four faces between. The angles are a regular octagon's (BCM's own diagram of the MCMR's section, in this length's gallery, draws one; this length's silhouette from 18.6° above is as high as one makes it), not measurements."},"mlok_bottom":{"type":"mlok","role":"slots","anchor":"mlok_bottom","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_bottom_slots}","interval":"={std.mlok.interval}","face_distance":"={.width} / 2","bore":"={.inside_diameter}","reach_inside":"={.reach_inside}"},"faces":{"bottom":{"angle":180,"note":"the underside (6 o'clock)"}},"flips":false,"note":"The underside, where BCM pictures its own Vertical Grip Mod 3 and KAG fitted (BCM-VG-MCMR-MOD-3-BLK-6, BCM-KAG-MCMR-BLK-5). No view looks at it square: its row's place is the family's reading, on the KAG's photo of an MCMR of a length it doesn't show, in line with the side faces' foremost slot (mlok_bottom_front_from_side_front), and its count is the side faces' (mlok_bottom_slots, assumed: where it ends at the rear is on no photo)."}},"materials":{"body":{"label":"Handguard","finish":"anodized","recolorable":true,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized","color":"placeholder-black","sku":"BCM-MCMR-13-556-BLK","source":"https://bravocompanyusa.com/bcm-mcmr-13-m-lok-compatible-modular-rail/"},"fde":{"label":"Flat Dark Earth","finish":"cerakote","color":"bcm-fde-cerakote","sku":"BCM-MCMR-13-556-FDE","source":"https://bravocompanyusa.com/bcm-mcmr-13-m-lok-compatible-modular-rail-flat-dark-earth/"}},"default":"black","note":"\"Hard Coat Anodized per Mil-A-8625F, Type III, Class 2\" (BCM's page for this length), and \"Flat Dark Earth Cerakote (LIMITED QTYS)\" as BCM-MCMR-13-556-FDE (its page for that one; Primary Arms: \"Color Flat Dark Earth Finish Cerakote\"): the grey-brown of the MCMR-15's, the same series of BCM's photographs (this length's side face between its rows of slots reads #7b766c on MCMR_13_FDE, 4d10da7d6e2b, region [450,666,1500,688], where the same reading of the 15's photo, 3c44f96c9c21, is #79736e). In both, what comes with it is black (BCM's photo of the Flat Dark Earth one with its hardware, 3b1493682ebf: the steel barrel nut, the lock block and its two cross bolts, the sling mount, a rail section; BCM's of the black one, a11c8b3fadd7): the barrel nut is inside it, the sling mount and the rail section are accessories in the box, and the two cross bolts are the slot `bolts`. Its marks (BCM's and Magpul's, the T-numbers) are white on both and aren't drawn."},"bolts":{"label":"Cross bolts","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The two cross bolts of its clamp, in their holes under the rail's rear: black on the black handguard and on the Flat Dark Earth one (BCM's photo of the Flat Dark Earth MCMR-13 laid out with its hardware, 3b1493682ebf: two black socket screws in a black block; T.REX ARMS' close photo of a black MCMR-13's clamp, 262151b23ff6, has the bolt's black head in its oval block). Steel; their finish isn't stated, and a black on steel isn't fitted to a photo."}},"components":{},"geometry":{"model":"bcm-mcmr-13-handguard.glb","components":{},"approximations":["Its section is the MCMR-15's (the family's, by BCM's own 1.5 in width and 1.3 in inside diameter on this length's page): a regular octagon across the 1.5 in, about the bore, with a neck up to the rail; no view shows it square on. The neck's width is where a 45° face reaches the height the 15's level photo shows it ending, and the corners are sharp but for a 0.012 in break (the photos show them a little rounded).","Its length is BCM's 13.4 in to the tips of the flare. The muzzle end is cut from four figures read on BCM's photo of this length from 18.6° above and brought back to a side view (no level photo of it alone is on file): the rail's front end and a square face under it down to 0.74 in above the bore, in the neck, a slope from there to the flat tips of the side faces (0.26 above to 0.32 below the bore), and a slope back from the tips to the bottom flat 0.35 in behind them, each square across: the 15's shape within what the reading carries. By BCM's length and the rail's place the tips come out 0.30 in ahead of the rail's front end; the photos have them 0.27 ahead (the 15's are 0.32).","The rail's 32 slots are the standard's, placed where the first reads on the complete upper's photos; its head is the standard's in section (MIL-STD-1913's Figure 1: lib.rail_head), its lower faces carried on to the neck's walls, as the 15 in rail's is since 2026-10-12.","Inside it is BCM's 1.3 in: a round bore from the rear end to the first M-LOK slot (how far the round part really runs isn't seen), then 1.3 in across inner flats that follow the outside, as BCM's three-quarter photos of this length show them. The neck is hollow by the same 0.1 in wall from end to end (light shows through its holes from side to side), and the room between its two walls is open down into the bore all the way back: BCM's photos of this length's rear end (43945a2790cd, and the black one's 09be27135ec4 from the other side) look in between the two walls from behind, down into the bore and out through the far wall's slot. That is where its clamp closes at 12 o'clock and where a gas tube runs back over the barrel nut to the receiver. The room's width (the neck's less a wall each side, 0.50 in) and its top (a wall's thickness under the rail's body, 0.885 in above the bore) aren't measured: a .180 in tube at the standard's 0.78 in above the bore has 0.015 in over it and the cross bolts just under it.","Seven M-LOK slots on each of six faces at the standard's size and pitch, the side faces' rows one rail pitch ahead of the others'; fifteen slanted and fifteen round holes a side under the rail, at this length's own count and place and at the 15's sizes, cut straight through from side to side; the two cross-bolt holes where this length's photo has them.","The underside's M-LOK row, at the standard's size and pitch, in line with the side faces' rows: no view looks at an MCMR's underside square, and BCM's photo of its KAG fitted there (the family's reading, on an MCMR of a length it doesn't show) shows the bottom face nearly edge-on, its two foremost slots dark in it, the foremost in line with the side faces' foremost (within 0.03 in) and one rail pitch ahead of the 4:30 face's. As many slots as a side face, assumed: the row's rear end shows on no photo. On this length the foremost ends 0.040 in short of the bottom flat's end, where the photo has an MCMR's end at it.","The two slots across its rear end under the rail (where its clamp is split and its index plate sits) are cut as the MCMR-15's level outline shows them, straight across: the clamp end is the family's (\"the same industry leading barrel nut and lock up design\"), and this length's photos, all from above, show the same two slots without giving their heights.","The two cross bolts are each a plain round pin a fiftieth narrower than its hole shows, from one upper face to the other across the room between the neck's walls, its ends just under the faces: their heads, and which side they go in from, are on no photo (BCM pictures the handguard off a rifle, its holes empty). They are their own material, black in both colours of handguard.","Not drawn: the teeth under the rail's rear end, the rear end's turned ring and the flats' run-out into it, the relief under each cross-bolt hole, the laser marks (the T-numbers in the rail's slots, BCM's and Magpul's on the sides), and its mounting hardware (barrel nut, clamp blocks, index plate: inside it or at the seam).","Its metal by the model is 6.36 cubic inches, which at aluminium's density is 10.0 oz against BCM's 8.2 oz for the handguard alone: the real walls, neck and rail are lighter than a 0.1 in wall everywhere and a solid rail make them (the 15's model is over by about as much)."],"ledger":["bcm-mcmr-13-handguard.length","bcm-mcmr-13-handguard.width","bcm-mcmr-13-handguard.height","bcm-mcmr-13-handguard.inside_diameter","bcm-mcmr-13-handguard.rear_x"]},"profiles":{},"gaps":[{"what":"A level side photo of this length alone (its muzzle end's two slopes are read on a photo from 18.6° above, each ± 0.03 to 0.05 in; the heights of the two slots across its rear end are the 15's)","need":"Primary Arms' gallery for BCM-MCMR-13-556-BLK (script-loaded: not fetched), whose first picture of the 15 is the level one; or any seller's straight side view"},{"what":"The underside's M-LOK row seen square: how many slots it has and where it begins at the rear (the row is the family's reading at its front end, on BCM's photo of its KAG fitted under an MCMR, with the bottom face nearly edge-on; its count is the side faces', assumed)","need":"A photo of this length from below, its whole underside in frame; a seller's gallery or a review may have one"},{"what":"The room inside its faces before the barrel (reach_inside: what an M-LOK accessory's nuts may take)","need":"The barrel's and the gas block's size under it, from the parts a build puts there"},{"what":"Its section square on (the neck's width, the room between its walls and how high it goes under the rail, the corners' rounding, the rail's dovetail)","need":"An end view with a known size in frame (the views of its rear end on file are three-quarter ones); BCM's diagram of the MCMR's section is undimensioned"},{"what":"Its two cross bolts' heads (each bolt is drawn as a plain pin as wide as its hole shows)","need":"a photo of an MCMR installed, from each side, close on the clamp"}]},"bcm-mcmr-15-handguard":{"id":"bcm-mcmr-15-handguard","name":"MCMR-15 (M-LOK® Compatible* Modular Rail)","manufacturer":"BCM","sku":"BCM-MCMR-15-556-BLK","url":"https://bravocompanyusa.com/bcm-mcmr-15-m-lok-compatible-modular-rail/","category":"handguard","description":"Bravo Company's 15 in free-float M-LOK handguard: \"Precision Machined Aerospace 6061-T6 Aluminum Alloy\", \"Hard Coat Anodized per Mil-A-8625F, Type III, Class 2\", \"mounting interfaces on seven sides in addition to the baked in MIL-STD-1913 at the 12 O'Clock position\", clamped at 12 o'clock on its own steel barrel nut by two cross bolts (US Patent 8904691). \"Designed to be used with pistol length, carbine length, mid length, or Mil-Spec M16 rifle length gas systems; all with a low profile gas block.\" The asterisk in its name is BCM's: \"*M-LOK® is a registered trademark of Magpul Industries Corp.\"","weight":"bcm-mcmr-15-handguard.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"mount":{"origin":[0,0,0],"note":"The receiver's front face on the bore axis, +x toward the muzzle."},"mlok":{"origin":["{.mlok_side_slot0_x}",0,0],"note":"On the handguard's axis (the bore's: an octagon about it) at the side faces' rearmost M-LOK slot's centre (index 0), +x toward the muzzle; the faces are angles about this axis (M10)."},"mlok_between":{"origin":["{.mlok_diag_slot0_x}",0,0],"note":"The same axis at the rearmost slot's centre of the four faces between the sides and the top and bottom: their rows sit one rail pitch (10 mm) behind the side faces'."},"mlok_bottom":{"origin":["{.mlok_bottom_slot0_x}",0,0],"note":"The same axis at the underside's rearmost M-LOK slot's centre (index 0): its row in line with the side faces' (read at its front end), with as many slots (assumed)."},"top_rail":{"origin":["{.rail_slot0_x}","{.rail_top_above_bore}",0],"note":"The rail's top at its rearmost slot's centre (the one marked T14), +x toward the muzzle (picatinny: index = slot number). Its own rail: the receiver's is the receiver's."}},"interfaces":{"handguard_mount":{"type":"ar15.handguard_mount","role":"handguard","anchor":"mount","params":{"nut":"standard"},"flips":false,"note":"BCM's installation manual: \"KMR series handguards (KMR, MCMR, QRF) are a free-floated design which mounts and aligns to the upper-receiver threads using a custom barrel nut\"; \"compatible ONLY with Mil-Spec direct impingement AR-15 platforms chambered in .223 Remington and/or 5.56x45mm NATO\". Its own barrel nut for the standard thread; \"A minimum gap of .005\" should exist to maintain the free-float of the barrel. Note: The gap should not exceed .040\"\" (rear_x)."},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}","beyond_seam":true,"seam_behind":"receiver","seam_ahead":"handguard"},"flips":false},"mlok":{"type":"mlok","role":"slots","anchor":"mlok","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_side_slots}","interval":"={std.mlok.interval}","face_distance":"={.width} / 2","bore":"={.inside_diameter}","reach_inside":"={.reach_inside}"},"faces":{"right":{"angle":90,"note":"the rifle's right side (+z)"},"left":{"angle":-90}},"flips":false,"note":"The side faces. How far an accessory's nuts may reach inside depends on the barrel and gas block under it, other parts: reach_inside has no figure, so that check reads as unmade."},"mlok_between":{"type":"mlok","role":"slots","anchor":"mlok_between","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_diag_slots}","interval":"={std.mlok.interval}","face_distance":"={.width} / 2","bore":"={.inside_diameter}","reach_inside":"={.reach_inside}"},"faces":{"right_upper":{"angle":45,"note":"between the rail and the right side (1:30)"},"right_lower":{"angle":135},"left_lower":{"angle":-135},"left_upper":{"angle":-45}},"flips":false,"note":"The four faces between. The angles are a regular octagon's (BCM's own diagram of its section draws one; the level photo's rows stand where one puts them), not measurements."},"mlok_bottom":{"type":"mlok","role":"slots","anchor":"mlok_bottom","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_bottom_slots}","interval":"={std.mlok.interval}","face_distance":"={.width} / 2","bore":"={.inside_diameter}","reach_inside":"={.reach_inside}"},"faces":{"bottom":{"angle":180,"note":"the underside (6 o'clock)"}},"flips":false,"note":"The underside, where BCM pictures its own Vertical Grip Mod 3 and KAG fitted (BCM-VG-MCMR-MOD-3-BLK-6, BCM-KAG-MCMR-BLK-5). No view looks at it square: its row's place is read at its front end on the KAG's photo, in line with the side faces' foremost slot (mlok_bottom_front_from_side_front), and its count is the side faces' (mlok_bottom_slots, assumed: where it ends at the rear is on no photo)."}},"materials":{"body":{"label":"Handguard","finish":"anodized","recolorable":true,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized","color":"placeholder-black","sku":"BCM-MCMR-15-556-BLK","source":"https://bravocompanyusa.com/bcm-mcmr-15-m-lok-compatible-modular-rail/"},"fde":{"label":"Flat Dark Earth","finish":"cerakote","color":"bcm-fde-cerakote","sku":"BCM-MCMR-15-556-FDE","source":"https://bravocompanyusa.com/bcm-mcmr-15-m-lok-compatible-modular-rail-flat-dark-earth/"}},"default":"black","note":"\"Hard Coat Anodized per Mil-A-8625F, Type III, Class 2\" (BCM), and \"Flat Dark Earth Cerakote (LIMITED QTYS)\" as BCM-MCMR-15-556-FDE: a grey-brown, greyer than the polymer of BCM's Flat Dark Earth stock and grip. In both, what comes with it is black (BCM's photo of the Flat Dark Earth one with its hardware: the steel barrel nut, the lock plate and its two cross bolts, the sling mount): the barrel nut is inside it, the sling mount is an accessory in the box, and the two cross bolts are the slot `bolts`."},"bolts":{"label":"Cross bolts","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The two cross bolts of its clamp, in their holes under the rail's rear: black on the black handguard and on the Flat Dark Earth one (BCM's photo of the Flat Dark Earth MCMR-15 laid out with its hardware, a39eb9705499: two black socket screws in a black block). Steel; their finish isn't stated, and a black on steel isn't fitted to a photo."}},"components":{},"geometry":{"model":"bcm-mcmr-15-handguard.glb","components":{},"approximations":["Its section is a regular octagon across BCM's 1.5 in, about the bore, with a neck up to the rail: BCM's own diagram of it draws one, and the level photo's three rows of slots and its bottom stand where one puts them, but no view shows the section square on. The neck's width is where a 45° face reaches the height the side photo shows it ending (0.70 in; BCM's diagram draws 0.61), and the corners are sharp but for a 0.012 in break (the photos show them a little rounded).","Its length is BCM's 15.0 in to the tips of the flare; the muzzle end is cut as the level side photo shows it, two straight slopes to the flat tips of the side faces, square across. The rail's 36 slots are the standard's, placed where the first reads on the complete upper's photo; its head is the standard's in section (MIL-STD-1913's Figure 1, since 2026-10-12; until then both its edges were sloped by what the side photo shows under the lower one, 0.01 in outside the standard's faces on top and 0.024 underneath), its lower faces carried on to the neck's walls. They reach a neck of the width drawn 0.18 in under the rail's top, where the side photo has the neck begin 0.215 ± 0.02 under it: a neck 0.63 in wide would agree with both, and BCM's diagram draws 0.61.","Inside it is BCM's 1.3 in: a round bore from the rear end to the first M-LOK slot (how far the round part really runs isn't seen), then 1.3 in across inner flats that follow the outside, as the photo of the muzzle end shows them; the neck is hollow by the same 0.1 in wall (light shows through its holes from side to side; its inside isn't seen).","Eight M-LOK slots on each of six faces at the standard's size and pitch, the side faces' rows one rail pitch ahead of the others'; sixteen slanted and sixteen round holes a side under the rail and the two cross-bolt holes, each at the size its outline reads on BCM's photo, cut straight through from side to side; the two slots across its rear end under the rail (where its clamp is split and its index plate sits) as the side outline shows them, cut straight across.","The underside's M-LOK row, at the standard's size and pitch, in line with the side faces' rows: no view looks at the underside square, and BCM's photo of its KAG fitted there from a little below the rifle's right side shows the bottom face nearly edge-on, its two foremost slots dark in it, the foremost in line with the side faces' foremost (within 0.03 in) and one rail pitch ahead of the 4:30 face's. As many slots as a side face, assumed: the row's rear end shows on no photo. The foremost cuts 0.025 in on into the foot of the muzzle end's slope, where the photo has it end at the slope.","The two cross bolts are each a plain round pin as wide as its hole shows, from one upper face to the other, its ends just under the faces: their heads, and which side they go in from, are on no photo (BCM pictures the handguard off a rifle, its holes empty). They are their own material, black in both colours of handguard.","Not drawn: the split along the top of its rear end where its clamp closes, the rear end's turned ring and the flats' run-out into it, the relief under each cross-bolt hole, the laser marks (T14 to T48 in the rail's slots, BCM's and Magpul's on the sides), and its mounting hardware (barrel nut, clamp blocks, cross bolts, index plate: inside it or at the seam).","Its metal by the model is 7.30 cubic inches, which at aluminium's density is 11.4 oz against BCM's 9.2 oz for the handguard alone: the real walls, neck and rail are lighter than a 0.1 in wall everywhere and a solid rail make them."],"ledger":["bcm-mcmr-15-handguard.length","bcm-mcmr-15-handguard.width","bcm-mcmr-15-handguard.height","bcm-mcmr-15-handguard.inside_diameter","bcm-mcmr-15-handguard.rear_x"]},"profiles":{"side":{"plane":"xy","origin":"the rear end (against the receiver) and the rail's top","offset":{"x":"rear_x","y":"rail_top_above_bore"},"points":[[0,-0.974],[0,-1.458],[0.013,-1.472],[0.013,-1.566],[0.027,-1.579],[0.04,-1.7],[0.081,-1.808],[0.134,-1.848],[0.148,-1.915],[0.168,-1.935],[0.276,-1.962],[0.329,-1.949],[0.343,-1.962],[4.845,-1.962],[4.859,-1.976],[11.915,-1.976],[11.929,-1.962],[14.59,-1.962],[14.852,-1.7],[14.987,-1.539],[15,-1.499],[15,-0.961],[14.785,-0.733],[14.61,-0.491],[14.597,-0.45],[14.597,-0.235],[14.61,-0.222],[14.61,-0.074],[14.59,-0.054],[14.267,-0.054],[14.241,-0.067],[14.214,-0.04],[14.066,-0.04],[14.052,-0.054],[13.905,-0.054],[13.878,-0.094],[13.851,-0.04],[13.676,-0.04],[13.663,-0.054],[13.542,-0.054],[13.501,-0.108],[13.474,-0.04],[13.273,-0.04],[13.259,-0.054],[13.165,-0.054],[13.138,-0.134],[13.118,-0.114],[13.118,-0.074],[13.098,-0.04],[12.856,-0.04],[12.802,-0.054],[12.782,-0.074],[12.782,-0.114],[12.762,-0.148],[12.742,-0.128],[12.742,-0.074],[12.722,-0.04],[12.695,-0.027],[12.574,-0.027],[12.56,-0.04],[12.426,-0.054],[12.406,-0.074],[12.406,-0.128],[12.372,-0.148],[12.352,-0.047],[12.332,-0.027],[12.184,-0.027],[12.171,-0.04],[12.09,-0.04],[12.063,-0.054],[12.03,-0.141],[11.996,-0.148],[11.976,-0.128],[11.956,-0.027],[11.794,-0.027],[11.781,-0.04],[11.7,-0.04],[11.653,-0.141],[11.606,-0.148],[11.586,-0.101],[11.586,-0.047],[11.566,-0.027],[11.405,-0.027],[11.324,-0.054],[11.297,-0.121],[11.27,-0.148],[11.23,-0.148],[11.196,-0.101],[11.19,-0.027],[11.015,-0.027],[10.974,-0.04],[10.907,-0.134],[10.84,-0.148],[10.806,-0.087],[10.8,-0.027],[10.625,-0.027],[10.544,-0.134],[10.437,-0.134],[10.41,-0.027],[10.262,-0.013],[10.242,-0.034],[10.242,-0.074],[10.208,-0.054],[10.202,-0.087],[10.155,-0.134],[10.047,-0.134],[10.027,-0.087],[10.027,-0.034],[10.007,-0.013],[9.859,-0.013],[9.852,-0.047],[9.778,-0.134],[9.657,-0.134],[9.637,-0.087],[9.637,-0.034],[9.617,-0.013],[9.469,-0.013],[9.449,-0.034],[9.462,-0.047],[9.456,-0.121],[9.442,-0.108],[9.388,-0.134],[9.267,-0.134],[9.247,-0.114],[9.247,-0.034],[9.227,-0.013],[9.079,-0.013],[9.059,-0.047],[9.073,-0.087],[9.039,-0.134],[8.864,-0.134],[8.858,-0.034],[8.837,-0.013],[8.69,-0.013],[8.669,-0.034],[8.663,-0.121],[8.636,-0.134],[8.474,-0.134],[8.454,-0.101],[8.448,-0.013],[8.286,-0.013],[8.273,-0.121],[8.246,-0.134],[8.085,-0.134],[8.065,-0.114],[8.058,-0.013],[7.897,-0.013],[7.89,-0.101],[7.856,-0.134],[7.695,-0.134],[7.661,-0.087],[7.655,-0.013],[7.493,-0.013],[7.487,-0.114],[7.466,-0.134],[7.332,-0.134],[7.319,-0.121],[7.305,-0.134],[7.272,-0.114],[7.265,-0.013],[7.103,-0.013],[7.09,-0.121],[6.956,-0.134],[6.882,-0.114],[6.882,-0.034],[6.835,0],[6.821,-0.013],[6.714,-0.013],[6.694,-0.074],[6.707,-0.087],[6.687,-0.121],[6.485,-0.121],[6.472,-0.013],[6.337,-0.013],[6.324,0],[6.304,-0.02],[6.304,-0.101],[6.284,-0.121],[6.095,-0.121],[6.089,-0.02],[6.042,0],[6.028,-0.013],[5.921,-0.013],[5.894,-0.121],[5.692,-0.121],[5.685,-0.02],[5.665,0],[5.544,0],[5.511,-0.02],[5.511,-0.101],[5.491,-0.121],[5.302,-0.121],[5.296,-0.02],[5.276,0],[5.141,0],[5.108,-0.047],[5.101,-0.121],[4.913,-0.121],[4.892,-0.087],[4.906,-0.02],[4.886,0],[4.738,0],[4.718,-0.02],[4.718,-0.087],[4.698,-0.121],[4.536,-0.121],[4.496,0],[4.348,0],[4.328,-0.02],[4.308,-0.121],[4.173,-0.121],[4.093,0],[3.945,0],[3.925,-0.034],[3.918,-0.121],[3.784,-0.121],[3.703,0],[3.569,0],[3.535,-0.02],[3.535,-0.087],[3.515,-0.121],[3.407,-0.121],[3.374,-0.06],[3.313,0],[3.165,0],[3.132,-0.06],[3.125,-0.121],[3.031,-0.121],[2.997,-0.047],[2.923,0],[2.776,0],[2.742,-0.06],[2.742,-0.114],[2.668,-0.121],[2.621,-0.047],[2.574,-0.013],[2.386,0],[2.352,-0.047],[2.339,-0.114],[2.292,-0.121],[2.258,-0.06],[2.198,-0.013],[2.077,0],[2.063,-0.013],[2.05,0],[2.036,-0.013],[1.996,0],[1.962,-0.047],[1.949,-0.114],[1.915,-0.121],[1.895,-0.074],[1.848,-0.027],[1.741,0],[1.606,0],[1.573,-0.047],[1.573,-0.087],[1.552,-0.121],[1.519,-0.101],[1.519,-0.06],[1.485,-0.027],[1.431,-0.013],[1.203,-0.013],[1.163,-0.121],[1.122,-0.04],[1.028,-0.013],[0.813,-0.013],[0.786,-0.108],[0.766,-0.087],[0.759,-0.04],[0.652,-0.027],[0.638,-0.013],[0.114,-0.013],[0.094,-0.06],[0.094,-0.141],[0.128,-0.175],[0.329,-0.175],[0.349,-0.235],[0.329,-0.255],[0.128,-0.255],[0.108,-0.289],[0.108,-0.41],[0.128,-0.444],[0.343,-0.444],[0.349,-0.491],[0.336,-0.531],[0.302,-0.551],[0.101,-0.551],[0.081,-0.571],[0.081,-0.612],[0.04,-0.719],[0.04,-0.773],[0.013,-0.853],[0.013,-0.961]],"scaleRefs":["bcm-mcmr-15-handguard.length"],"inputs":{"bcm-mcmr-15-handguard.length":15},"tolerance":0.01,"photo":"references/bcm-mcmr-15-handguard 13f345fa4b4e (Primary Arms' gallery, BCM-MCMR-15-556-BLK_01: the handguard alone, its right side seen level, 1152 x 768)","method":"luminance < 200, largest piece, holes filled; scale from bcm-mcmr-15-handguard.length = 15 in (x-extent 1116 px → 74.4 px/in); origin at x min, y max of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 293 points (IoU 0.999 with the full outline); checks: height 1.976 ± 0.041 in vs bcm-mcmr-15-handguard.height 1.95 ± 0.03 (provisional): agrees (tools/trace.py)","via":"harvest","note":"The slots and holes are inside the outline (filled); the model cuts them. Its two ends are right by BCM's length; its rail and its heights read about 2% small (the lens stood about 30 in away, and the ends are 0.75 in nearer it than the rail), so the model takes the rail's slots, its top and the bottom from the ledger and this outline's two ends."}},"gaps":[{"what":"The underside's M-LOK row seen square: how many slots it has and where it begins at the rear (the row is read at its front end only, on BCM's photo of its KAG fitted there, with the bottom face nearly edge-on; its count is the side faces', assumed)","need":"A photo of an MCMR from below, its whole underside in frame; a seller's gallery or a review may have one"},{"what":"The room inside its faces before the barrel (reach_inside: what an M-LOK accessory's nuts may take)","need":"The barrel's and the gas block's size under it, from the parts a build puts there"},{"what":"Its section square on (the neck's width, the corners' rounding, the rail's dovetail)","need":"An end view with a known size in frame; BCM's diagram of it is undimensioned"},{"what":"Its two cross bolts' heads (each bolt is drawn as a plain pin as wide as its hole, its ends just inside the upper faces: BCM's photos of the handguard are of it off a rifle, the holes empty)","need":"a photo of an MCMR installed, from each side, close on the clamp"}]},"bcm-mid-gas-tube":{"id":"bcm-mid-gas-tube","name":"Gas Tube - Mid Length","manufacturer":"BCM","sku":"Gas-Tube-Mid-Length","url":"https://bravocompanyusa.com/gas-tube-mid-length/","category":"gas_tube","description":"BCM's gas tube for a mid-length gas system. BCM: \"Gas tube for Mid Length gas system, AR15. Includes roll pin. Length: Approximately 11 3/4\"\".","weight":"bcm-mid-gas-tube.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"block":{"origin":[0,0,0]}},"interfaces":{"gas_tube":{"type":"ar15.gas_tube","role":"tube","anchor":"block","params":{},"flips":false},"gas_system":{"type":"ar15.gas_system","role":"tube","params":{"length":"mid"},"flips":false,"note":"BCM names it \"Gas Tube - Mid Length\". What the platform checks a gas tube against a barrel by (D83)."}},"materials":{"tube":{"label":"Gas tube","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"BCM's page names no material or finish; its photo of the four tube lengths (e732d2ac52b0, 1024 x 212) shows them bright, as stainless tubes are, and none blackened. Bright metal isn't fitted to a photo: the app's natural stainless. One piece: the roll pin it comes with isn't drawn."}},"components":{},"geometry":{"components":{},"approximations":[],"ledger":["bcm-mid-gas-tube.length","bcm-mid-gas-tube.od"]},"profiles":{},"gaps":[{"what":"Its weight","need":"A figure from BCM or from a seller's page for it (BCM's page states none): until then a build with it says its weight isn't known"},{"what":"Where its bend lies along its length","need":"A straight side view of the mid-length tube with its bend in the picture's plane (BCM's photo has the bends turned from the camera); the Army's drawing dimensions the rifle's tube"}]},"bcm-mk2-buffer-t0":{"id":"bcm-mk2-buffer-t0","name":"MK2 Buffer Mod 1 - T0","manufacturer":"BCM","sku":"BCM-BFMK2-M1-T0","url":"https://bravocompanyusa.com/bcm-mk2-buffer-t0","category":"buffer","description":"The intermediate-length buffer of BCM's MK2 recoil mitigation system, the lightest of its five weights (T0 to T4). BCM: \"THE BCM® MK2 BUFFER MOD1- T0, Intermediate Length (BUFFER ONLY) (weight = approximately 3.8oz)\"; \"Increased internal counterweight travel reduces bolt bounce\"; \"Internal spring to reduce noise of counter weight shifting and ensure more consistent weight placement\"; \"Made of 7075T6 aluminum, hard coat anodized for lasting endurance.\" \"BCM US Patent #10415907\". BCM recommends \"heavier buffer weights for short barreled and suppressed platforms, starting with the T0 buffer weight and increasing to T1, or more as needed based on performance\" (its MK2 RMS page).","weight":"bcm-mk2-buffer-t0.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[{"slot":"receiver_extension","parts":["bcm-mk2-receiver-extension"],"says":"BCM, MK2 Buffer Mod 1 - T0: \"IMPORTANT NOTE: MK2 MOD 1 buffer series is to ONLY be used on the AR15 receiver platform and it ONLY works in conjunction with the BCM MK2 Receiver Extension (BCM part #BCM-MK2-RE) and the Mil-Spec Rifle M16 Action Spring (BCM part # SPRING-RIFLE-M16-ACTION). To use any other component, not specifically developed to function with the MK2 MOD1 Intermediate Buffer can cause damage to the weapon and possibly injure the operator.\"","source":"https://bravocompanyusa.com/bcm-mk2-buffer-t0"},{"slot":"buffer_spring","parts":["bcm-rifle-m16-action-spring"],"says":"BCM, MK2 Buffer Mod 1 - T0: \"it ONLY works in conjunction with the BCM MK2 Receiver Extension (BCM part #BCM-MK2-RE) and the Mil-Spec Rifle M16 Action Spring (BCM part # SPRING-RIFLE-M16-ACTION).\"","source":"https://bravocompanyusa.com/bcm-mk2-buffer-t0"}],"anchors":{"bore":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the buffer's axis at its head's front face, +x rearward (toward its bumper)."}},"interfaces":{"bore":{"type":"ar15.extension_bore","role":"buffer","anchor":"bore","params":{},"flips":false}},"materials":{"body":{"label":"Buffer body","finish":"anodized","recolorable":false,"color":"placeholder-black","note":"BCM: \"Made of 7075T6 aluminum, hard coat anodized\"; its drawing: \"7075-T6 Intermediate Length Buffer body. Anodized Black for Easy Identification.\" Black in every photo of it. Black anodize is the catalog's stand-in black, not a fitted colour."},"bumper":{"label":"Bumper","finish":"polymer","recolorable":false,"color":"bcm-buffer-bumper","note":"BCM's drawing: \"MIL-SPEC Polyether Urethane Bumper\". A translucent cream in BCM's kit photo on white (da2d35d9e02d: its lit side reads about #d8ce9d), a paler green-white in its photos on wood: the urethane's batch, as on BCM's carbine buffers, whose fitted cream is taken."},"pin":{"label":"Pin","finish":"steel","recolorable":false,"color":"steel-phosphate-dark","note":"The pin across the body and the bumper: a dark dot in a hole in BCM's photos (040474c9f6d0, da2d35d9e02d)."}},"components":{},"geometry":{"model":"bcm-mk2-buffer-t0.glb","components":{},"approximations":["The standard carbine buffer's pattern (lib.carbine_buffer: the Army's drawings of the buffer's head, bumper and pin, the reference model's body) at this buffer's own length: BCM's photos have the standard's head with its flats, the collar behind it and the standard's bumper standing out of a body 0.8 in longer than a carbine's, and its pin closer to the bumper, all of which are read on them. BCM states no size.","Not drawn: what is inside it (BCM's drawing and its patent, US 10,415,907: four weights with spacers between them, a flat-wire preload spring and the bumper's stop), which is what the T1 to T4 change; the marks on its face (BCM, PAT. 10415907, MK2-M001, T0, in BCM's photo of the five).","In a build its face rests where the bolt carrier's rear end stands with the bolt forward, at the upper receiver's rear face (the Army's drawings), as every buffer is placed."],"ledger":["bcm-mk2-buffer-t0.length","bcm-mk2-buffer-t0.od","bcm-mk2-buffer-t0.head_thickness","bcm-mk2-buffer-t0.collar_d","bcm-mk2-buffer-t0.bumper_exposed","bcm-mk2-buffer-t0.body_length","bcm-mk2-buffer-t0.pin_from_open_end","bcm-mk2-buffer-t0.pin_d"]},"profiles":{},"gaps":[{"what":"Its sizes from BCM","need":"BCM's figures or a drawing to scale: its length is read on BCM's photo beside the MK2 tube; its head, collar, body and bumper are the standard's, which the photos bear out"}]},"bcm-mk2-charging-handle":{"id":"bcm-mk2-charging-handle","name":"Ambidextrous MK2 Charging Handle - Large Latch (5.56mm/.223)","manufacturer":"BCM","sku":"BCM-GFH-MK2-LRG-AMBI","url":"https://bravocompanyusa.com/bcm-ambidextrous-mk2-charging-handle-large-latch-5-56mm-223/","category":"charging_handle","description":"BCM's ambidextrous MK2 charging handle with the large latches: a latch each side of a fixed rear grip, either one unlatching it. \"MIL-SPEC grade forgings and machined from 7075 T6 aluminum, with a hard coat anodized finish per Mil-A-8625F, Type III, Class 2\"; \"Compatible with Mil-Spec AR-15 Direct Impingement Weapon Systems\"; \"NOT compatible with adjustable gas keyed bolt carrier groups.\" (BCM's page).","weight":"bcm-mk2-charging-handle.weight","cartridge":{"takes":["5.56 NATO",".223 Rem"],"stated":"BCM® Ambidextrous MK2 Charging Handle - Large Latch (5.56mm/.223)","source":"https://bravocompanyusa.com/bcm-ambidextrous-mk2-charging-handle-large-latch-5-56mm-223/ (the product's name on BCM's page, as cached: harvest.quote; its text names no cartridge, and the handle is laser marked 5.56mm)"},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"channel":{"origin":[0,0,0],"note":"The T's shoulder on the channel's axis, +x toward the muzzle (the front faces of its block on the right and of its body behind the latch's hook on the left): it stops against the front wall of the open notch under a receiver's rail's rear end (the receiver's handle_seat_x), and the front hook's tip is `length` ahead."}},"interfaces":{"charging_handle_channel":{"type":"ar15.charging_handle_channel","role":"handle","anchor":"channel","params":{},"flips":false}},"materials":{"body":{"label":"Charging handle","finish":"anodized","recolorable":false,"color":"placeholder-black","note":"Sold in black only: \"hard coat anodized finish per Mil-A-8625F, Type III, Class 2\" (BCM); Scheels and Primary Arms list its colour as Black."},"pins":{"label":"Latch pins","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"The two latches' roll pins, bright in every photo; what steel they are isn't stated."}},"components":{},"geometry":{"model":"bcm-mk2-charging-handle.glb","components":{},"approximations":["Ahead of its shoulder it is cut by what of a forged upper stands beside it (2026-10-20, lib.handle_room): the walls either side of the channel's rear slot, out to the forging's side under the rail (std.ar15.rail_tongue_half_width, ±0.318), the left one less the Army drawing's latch slot, where the hook lies (8448524 Section D-D: .045 of wall left over the channel); and behind it the notch's front wall's two corners, cut back at 45 degrees. Its photos show the latch's arm and the shaft as one outline, where the wall between them is .045 to .109 thick: every handle on file had its arm drawn through it.","Its plan is BCM's own photo from above (the latches, the shoulder block, the latch's hook and its notch, the nose, the guide lugs), scaled by the shaft's width; the shaft is put to the Army drawing's length, which the photo reads 1% long (not told apart from it at the photo's scale).","The shaft's thickness, its key channel, its front hook and its guide lugs' height are the Army's drawing's (8448518), which BCM's handle is made to work with: only the hook's drop and length and the lugs' place were checked on BCM's photos. The channel is cut from the shoulder to the hook and runs through the hook as a bore on its own roof's centre; where it ends inside the T, and the bore's own height (the drawing's is .024 in lower), aren't drawn.","The T is one slab from the shaft's underside to the latches' top face: the latches are open along their rear edges on the real handle (a top plate and a bottom plate), the round pockets underneath and BCM's gas channels aren't drawn; the two hubs are only their outlines, a line 0.015 in wide cut in the top face. The shoulder block's and the latch hook's heights aren't sourced: drawn at the latches'.","The rear grip (its two lobes and the rim between them) is drawn as its plan at one height, its edges rounded off by 0.03 in for the look: its sculpted top, the slope from its rim down to the hubs and the grooves down its rear face aren't sourced.","The grooves down each latch's front face: their count and pitch are read off the photos, their width is taken as half the pitch, their walls square; the left latch's are the right's mirrored. The top chamfers run to the hook's rear face (BCM's end in a round run-out short of the nose).","The two pins are drawn as discs at their ends' size, flush in the latches' top face (they are roll pins: rings). Edges broken at 0.012 in."],"ledger":["bcm-mk2-charging-handle.length","bcm-mk2-charging-handle.shaft_width","bcm-mk2-charging-handle.shaft_thickness","bcm-mk2-charging-handle.top_flat_width","bcm-mk2-charging-handle.top_chamfer_drop","bcm-mk2-charging-handle.top_chamfer_from_shoulder","bcm-mk2-charging-handle.channel_width","bcm-mk2-charging-handle.channel_depth","bcm-mk2-charging-handle.hook_length","bcm-mk2-charging-handle.hook_drop","bcm-mk2-charging-handle.hook_fillet_r","bcm-mk2-charging-handle.guide_lug_height","bcm-mk2-charging-handle.latch_thickness","bcm-mk2-charging-handle.latch_front_height","bcm-mk2-charging-handle.t_height","bcm-mk2-charging-handle.rib_pitch","bcm-mk2-charging-handle.rib_count","bcm-mk2-charging-handle.rib_depth","bcm-mk2-charging-handle.rib_first_z","bcm-mk2-charging-handle.pin_behind_shoulder","bcm-mk2-charging-handle.pin_off_centre","bcm-mk2-charging-handle.pin_d","bcm-mk2-charging-handle.hub_r"]},"profiles":{"plan":{"plane":"xz","origin":"the T's shoulder (the front faces of its block on the right and of its body behind the latch's hook on the left, at their top edges: column 1080.5 of the photo) on the shaft's centre line, +x toward the muzzle, z to the handle's right","offset":{},"points":[[-1.014,0.007],[-1.009,-0.079],[-0.985,-0.107],[-0.974,-0.142],[-0.974,-0.176],[-0.985,-0.199],[-0.98,-0.211],[-0.98,-0.279],[-0.985,-0.285],[-0.98,-0.291],[-0.985,-0.308],[-0.98,-0.383],[-0.991,-0.412],[-0.985,-0.434],[-0.997,-0.446],[-0.997,-0.475],[-0.962,-0.584],[-0.916,-0.664],[-0.889,-0.689],[-0.823,-0.715],[-0.811,-0.761],[-0.77,-0.818],[-0.759,-0.858],[-0.73,-0.881],[-0.724,-0.909],[-0.701,-0.921],[-0.695,-0.949],[-0.666,-0.972],[-0.666,-0.995],[-0.637,-1.012],[-0.631,-1.046],[-0.498,-1.234],[-0.425,-1.288],[-0.356,-1.311],[-0.263,-1.31],[-0.223,-1.292],[-0.191,-1.255],[-0.185,-1.198],[-0.202,-1.158],[-0.249,-1.124],[-0.237,-1.107],[-0.272,-1.084],[-0.266,-1.055],[-0.301,-1.021],[-0.295,-0.992],[-0.315,-0.984],[-0.324,-0.97],[-0.312,-0.947],[-0.341,-0.918],[-0.341,-0.907],[-0.33,-0.895],[-0.359,-0.861],[-0.347,-0.832],[-0.37,-0.81],[-0.37,-0.798],[-0.359,-0.792],[-0.359,-0.77],[-0.376,-0.764],[-0.382,-0.747],[-0.364,-0.735],[-0.364,-0.718],[-0.387,-0.701],[-0.387,-0.689],[-0.37,-0.678],[-0.37,-0.661],[-0.387,-0.649],[-0.387,-0.632],[-0.37,-0.621],[-0.37,-0.598],[-0.387,-0.592],[-0.387,-0.575],[-0.37,-0.563],[-0.359,-0.523],[-0.321,-0.486],[-0.292,-0.474],[-0.234,-0.474],[-0.199,-0.485],[0.182,-0.472],[0.291,-0.443],[0.32,-0.431],[0.34,-0.411],[0.346,-0.297],[0.34,-0.268],[0.32,-0.243],[0.28,-0.22],[0.199,-0.22],[0.185,-0.235],[0.19,-0.303],[0.182,-0.318],[0.164,-0.323],[0.014,-0.324],[0,-0.31],[0,-0.207],[0.02,-0.198],[0.188,-0.198],[0.193,-0.203],[0.608,-0.196],[0.614,-0.202],[4.571,-0.198],[4.654,-0.237],[4.877,-0.237],[4.927,-0.208],[4.966,-0.197],[5.847,-0.199],[5.869,-0.188],[5.927,-0.118],[5.955,-0.017],[5.944,0.072],[5.916,0.134],[5.869,0.187],[5.847,0.198],[4.988,0.196],[4.983,0.202],[4.977,0.196],[4.972,0.202],[4.938,0.196],[4.936,0.204],[4.944,0.213],[4.849,0.246],[4.666,0.246],[4.615,0.218],[4.579,0.209],[4.621,0.206],[4.621,0.201],[4.42,0.2],[4.415,0.195],[4.409,0.2],[4.32,0.194],[4.314,0.2],[2.327,0.196],[2.315,0.201],[2.31,0.196],[2.23,0.196],[2.219,0.201],[2.207,0.195],[2.202,0.201],[0.159,0.197],[0.153,0.202],[0.009,0.202],[0,0.211],[0,0.314],[-0.009,0.322],[-0.026,0.322],[-0.032,0.334],[-0.052,0.336],[-0.052,0.365],[-0.066,0.379],[-0.211,0.396],[-0.269,0.413],[-0.335,0.473],[-0.359,0.531],[-0.359,0.553],[-0.382,0.576],[-0.382,0.588],[-0.364,0.605],[-0.364,0.622],[-0.382,0.634],[-0.382,0.645],[-0.364,0.662],[-0.376,0.702],[-0.359,0.714],[-0.359,0.737],[-0.37,0.742],[-0.37,0.76],[-0.356,0.763],[-0.347,0.783],[-0.359,0.8],[-0.359,0.817],[-0.335,0.84],[-0.347,0.851],[-0.347,0.868],[-0.324,0.886],[-0.324,0.903],[-0.335,0.914],[-0.306,0.943],[-0.312,0.977],[-0.289,0.989],[-0.283,1.006],[-0.289,1.029],[-0.26,1.052],[-0.266,1.08],[-0.237,1.097],[-0.231,1.137],[-0.202,1.149],[-0.179,1.195],[-0.179,1.246],[-0.191,1.269],[-0.223,1.301],[-0.257,1.312],[-0.35,1.312],[-0.396,1.301],[-0.442,1.278],[-0.503,1.224],[-0.619,1.058],[-0.625,1.023],[-0.66,0.995],[-0.66,0.972],[-0.689,0.949],[-0.695,0.92],[-0.724,0.903],[-0.724,0.88],[-0.753,0.857],[-0.759,0.828],[-0.776,0.817],[-0.811,0.76],[-0.823,0.731],[-0.823,0.708],[-0.86,0.699],[-0.889,0.682],[-0.939,0.622],[-0.974,0.553],[-0.997,0.473],[-0.997,0.438],[-0.985,0.427],[-0.997,0.392],[-0.991,0.375],[-0.974,0.364],[-0.974,0.341],[-0.985,0.318],[-0.98,0.306],[-0.985,0.272],[-0.98,0.249],[-0.98,0.105],[-0.985,0.094],[-0.98,0.088],[-1.009,0.048]],"features":{"rear_grip":[[[-0.564,0.72],[-0.692,0.737],[-0.82,0.719],[-0.924,0.662],[-0.977,0.576],[-1,0.432],[-1.012,0.26],[-1.017,0.002],[-1.012,-0.257],[-1,-0.429],[-0.977,-0.572],[-0.924,-0.664],[-0.82,-0.721],[-0.692,-0.737],[-0.564,-0.725],[-0.489,-0.684],[-0.46,-0.598],[-0.46,-0.426],[-0.518,-0.386],[-0.605,-0.341],[-0.669,-0.255],[-0.727,-0.141],[-0.75,0.003],[-0.727,0.146],[-0.669,0.261],[-0.605,0.347],[-0.518,0.393],[-0.46,0.422],[-0.46,0.605],[-0.489,0.685]]]},"scaleRefs":["bcm-mk2-charging-handle.shaft_width"],"inputs":{"bcm-mk2-charging-handle.shaft_width":0.4},"tolerance":0.005,"photo":"references/bcm-mk2-charging-handle 02410675303b (BCM's gallery: the large two-latch handle from above, on white, 1280 x 854)","method":"luminance < 100, largest piece, holes filled; scale from bcm-mk2-charging-handle.shaft_width = 0.4 in, the tube's own width column by column: 71.5 px over columns 50–195, 70.8 px over columns 284–324, 70.3 px over columns 874–894, 70.1 px over columns 988–1000; a line through them (rms 0.14 px) changes -2.0% from column 50 to 1000, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 640)/width, the lens's axis taken to meet the image at column 640; 176.5 px/in there. The axis is the tube's centre line (tilt -0.17°, rms 0.04 px); origin at column 1080.5 of the photo, on the tube's axis; Douglas-Peucker at 0.005 in with the extremes kept: 226 points (IoU 0.993 with the full outline); The photo is taken from close above the handle's middle (the shaft reads 2% wider at its front end, and the latches' front faces show as grey bands): the mask is the dark top faces, the bands left out, so the outline is the top faces' edges.; checks: x_max 5.955 ± 0.084 in vs bcm-mk2-charging-handle.length 5.895 ± 0.01 (confirmed): agrees; height in x [4.68, 4.82] 0.483 ± 0.018 in vs bcm-mk2-charging-handle.guide_lug_width 0.488 ± 0.005 (confirmed): agrees; features through the same placement (rear_grip: the rear grip (the fixed body's matte, sculpted rear wall): its two lobes over the latches' roots and the crescent between them round the hubs, picked on the photo at 5.5x; its rear side is drawn past the outline, which is its edge there) (tools/trace.py)","via":"harvest","note":"From above: the shaft with its nose and guide lugs, the T's shoulder block on the right and the latch's hook on the left, the two latches swept forward, the rear grip."}},"gaps":[{"what":"Its weight","need":"BCM's own figure, or a reviewer's scale: BCM states none, and the one seller's 0.18 lb is twice what the modelled solid would weigh in aluminium (it may be a packed weight)."},{"what":"A straight side view","need":"A photo square to the handle's side (none is on file): the rear grip's profile, its lobes' crests, the latches' open rear edges and the shoulder block's and hook's heights."},{"what":"Its seat checked on a photo of it in a receiver","need":"A pin-framed photo of the handle latched in an upper: it is placed with its shoulder against the front wall of the receiver's notch (2026-10-05), as the Army's handle stops, which puts its latch's hook 0.02 to 0.045 in past the front end of the one latch slot traced (Expo Arms' left side) and its rear grip's two lobes in the square rear corners the app draws on a rail (the real rail's end is rounded)."}]},"bcm-mk2-lower-receiver":{"id":"bcm-mk2-lower-receiver","name":"MK2 AR-15 Lower Receiver","manufacturer":"BCM","url":"https://www.primaryarms.com/bcm-mk2-ar-15-complete-lower-receiver-no-stock","category":"lower","description":"BCM's lower receiver as it comes in its MK2 complete lower: \"Forged 7075-T6 aluminum construction\", \"Type III hardcoat anodized finish\", \"Multi-Caliber marked\" (Primary Arms), its left side marked \"BCM RIFLE COMPANY / MODEL BCM4 / CAL. MULTI\" and \"BRAVO COMPANY MFG. INC. / HARTLAND WISCONSIN / USA\" (Primary Arms' photos). Its parts kit is installed (the pins, the selector, \"Non-Ambi\", the bolt catch, the magazine catch and their springs and detents) and so is BCM's polymer trigger guard (\"Enlarged polymer trigger guard for gloved use\", Primary Arms of the Mod 0 stock lower; \"Enlarged trigger guard\", of the blem). The trigger (\"PNT (Polished Nickel Teflon) trigger\"), the grip (\"BCM ergonomic pistol grip\"; \"BCM Mod 4 pistol grip\" on the blem's page) and the MK2 receiver extension with its \"T0 buffer (3.8 oz)\" are parts of their own in the complete lower's kit. \"Ready for any compatible stock or pistol brace\". The blem's page also says \"Low shelf, compatible with RDIAS or Accu-Wedge\" (the shelf at the fire-control pocket's rear: its inside is drawn as the Army drawing's).","weight":"bcm-mk2-lower-receiver.weight","occupies":["lpk","trigger_guard"],"integral":[],"brings":["selector"],"seats":{},"requires":[],"anchors":{"pins":{"origin":[0,0,0],"note":"The rifle frame origin."},"buffer_tube_mount":{"origin":[0,"{.buffer_axis_above_pin}",0],"x":[-1,0,0]},"magwell":{"origin":["{.magazine_seat_x}","{std.ar15.mag_catch_slot_bottom_y} + {std.ar15.mag_catch_slot_h}",0],"note":"Where a seated magazine hangs: x where its spine's rear face sits in the well, y at the catch's upper face (the standard's slot). A magazine's own anchor is the upper edge of its catch notch."},"grip_lug":{"origin":[0,"{.grip_seat_y}",0]},"trigger_guard":{"origin":["{.trigger_guard_front_x}","{.trigger_guard_front_y}",0],"x":["{.trigger_guard_front_x} - {.trigger_guard_rear_x}","{.trigger_guard_front_y} - {.trigger_guard_rear_y}",0],"note":"The Army drawing's two ear holes, where BCM's guard is pinned; the slot is occupied by this part (its guard), so nothing else mates here."},"fcg":{"origin":["{.trigger_pin_x}","{.trigger_pin_y}",0]},"lpk":{"origin":[0,0,"-{std.ar15.lower_body_width} / 2"]},"selector":{"origin":["{std.ar15.selector_x}","{std.ar15.selector_y}",0],"note":"The selector's hole, on its axis at the receiver's mid-plane (D86)."}},"interfaces":{"receiver_pins":{"type":"ar15.upper_lower","role":"lower","anchor":"pins","params":{"pin_spacing":"={std.ar15.pin_spacing}"},"flips":false,"note":"Primary Arms, of the Mod 0 stock lower: \"a fully assembled, recoil-tuned lower ready for any Mil-Spec upper\"; of this one: \"pairs seamlessly with any BCM upper\"."},"buffer_tube_mount":{"type":"ar15.buffer_tube_mount","role":"receiver","anchor":"buffer_tube_mount","params":{},"flips":false},"magwell":{"type":"ar15.magwell","role":"receiver","anchor":"magwell","params":{"family":"5.56"},"flips":false,"note":"A standard AR-15 well: \"Multi-Caliber marked\" and mil-spec throughout (Primary Arms); its catch's button is where the Army drawing has the catch (the right photo)."},"grip_lug":{"type":"ar15.grip_lug","role":"receiver","anchor":"grip_lug","params":{},"flips":false},"trigger_guard":{"type":"ar15.trigger_guard","role":"receiver","anchor":"trigger_guard","params":{},"flips":false},"fcg":{"type":"ar15.fcg","role":"receiver","anchor":"fcg","params":{"pin_diameter":"small-pin"},"flips":false,"note":"Primary Arms: \"Trigger Pin Diameter MIL-SPEC .154\" (all three pages)."},"lpk":{"type":"ar15.lpk","role":"receiver","anchor":"lpk","params":{},"flips":false},"selector":{"type":"ar15.selector","role":"receiver","anchor":"selector","params":{},"flips":false}},"materials":{"receiver":{"label":"Receiver","finish":"anodized","recolorable":true,"color":"placeholder-black","sheen":"matte","options":{"black":{"label":"Black","finish":"anodized","color":"placeholder-black","sheen":"matte","source":"https://www.primaryarms.com/bcm-mk2-ar-15-complete-lower-receiver-no-stock"}},"default":"black","note":"\"Type III hardcoat anodized finish\", \"Color Black\", \"Finish Hardcoat Anodized\" (Primary Arms). Sold in black only: the blem (LRG-RMS-NO-STOCK-COSMO) is the same black with cosmetic flaws, and the Mod 0 stock lower (LRG-RMS-STK-MOD-0-BLK, another product) has the same black receiver in all its photos. A black on sealed hard anodize: its finish type is its look, not fitted to a photo (D81)."},"guard":{"label":"Trigger guard","finish":"polymer","recolorable":false,"color":"placeholder-polymer-black","sheen":"matte","note":"BCM's polymer guard: \"Made of impact resistant polymer\" (BCM, BCM-GTG-MOD-0-BLK); \"Enlarged polymer trigger guard for gloved use\" (Primary Arms, the Mod 0 stock lower). Black in every photo of the complete lower; BCM sells the guard alone in black and in Flat Dark Earth, and the complete lower in black only. A black polymer: not fitted to a photo."},"controls":{"label":"Controls","finish":"steel","recolorable":false,"color":"placeholder-black","note":"Its parts kit: the pins' heads and ends, the selector on SAFE, the bolt catch, the magazine catch's button. BCM, of its kit's bolt catch and selector: \"a Mil-Spec AISI8620 investment casting per the USGI TDP for M16/M4\" (its enhanced parts kit's page). Black against the black receiver in Primary Arms' photos; BCM names no finish for them. A black, not fitted to a photo."}},"components":{"receiver":{"label":"Receiver","material":"receiver"},"guard":{"label":"Trigger guard","material":"guard"},"selector":{"label":"Selector","material":"controls"}},"geometry":{"components":{"receiver":"bcm-mk2-lower-receiver.receiver.glb","guard":"bcm-mk2-lower-receiver.guard.glb","selector":"bcm-mk2-lower-receiver.selector.glb"},"approximations":["Its interfaces are the Army drawing's (8448608): the pins, the selector, the trigger and hammer pins, the guard's two holes, the deck, the buffer tower's ring and bore, the grip's seat and lug, the rear walls' arc, the inside (D46: the fire-control pocket, the rear lug's slot, the safety detent's boss, the trigger slot, the well and its spine slot) and the catches' cuts. Primary Arms of this lower: \"ready for any Mil-Spec upper\", \"Trigger Pin Diameter MIL-SPEC .154\"; BCM of its kit's parts: \"all MIL SPEC lower receivers built per the USGI TDP\". On the right photo, framed by least squares to its pins and five holes, every hole is within 0.045 in of the drawing's place.","Its own shape is the right side's outline (Primary Arms' square photo of the no-stock lower, 134 px to the inch): the tower's walls sweeping down to the deck, the deck (the drawing's plane), the pivot lug, the magazine well with its lower edge rising toward the front, the front ears. Its pivot lug's front is round about the pivot pin to 6.568 ahead of the takedown pin, where the left photo has it: the right photo's front is the pin's domed head, which stands over the lug (the parts kit's head is the app's).","What the grip, the guard and the trigger hide in every photo is the drawing's, as on the catalog's other forged mil-spec lowers: the grip's seat 1.318 below the deck, the lug (.375 wide, its sloped face 1.228 from the pin at 60 degrees, its flat .93 below the seat), the rear underside rounded across (the reference CAD model's arc and half-round), the ears 0.659 across with the guard's .442 gap. The ears' feet and where the trigger's opening begins and ends at the seat are this lower's right photo's; the opening itself is the photo's (the backdrop between the ears and the guard, traced: the ears' inner edges curve), cut straight through both walls.","The well's walls are the outline at the drawing's 1.098 across, each from its own rear edge (the right side's at 3.59; the left's upper part from 3.03 down to an S-curve that ends at the front ears at 3.44, from the left photo). The raised band down the left wall and the catch's round boss on it are the reference CAD model's; the bolt catch's two bosses are the left photo's ends at the drawing's face (0.618), either side of the drawing's slot (the photo's gap is 0.05 ahead of it and as wide). The magazine catch's fence on the right is the photo's frame round the button, its face on the walls' plane, run on into the wall and up under the roll; the roll along the well's right top has its lower edge (-0.202) and its two ends from the right photo, and its crest 0.80 from the centre plane assumed (no view looks along the receiver).","The buffer tower's ring is the drawing's (its top, its rear face, 1.392 across about the bore's axis), bored through at the mil-spec extension's OD (its thread isn't on file); the right photo's ring is behind BCM's QD end plate and castle nut, which were taken out of the outline. The walls ahead of it rise along the Army drawing's arc (.750 R, 8448608 sheet 1) and no higher (lib.lower_rear_walls): the right photo has them up to the ring's shoulder, as a silhouette from a lens ahead of the tower shows the far wall.","It is drawn at the standard's widths throughout: no page says whether this is BCM's standard forging or a widebody one, and no view on file looks along it.","The trigger guard is BCM's polymer one (\"BCM Enhanced Trigger Guard\" in BCM's parts kit; sold alone as BCM-GTG-MOD-0): its outline where it shows below the ears on the right photo (bowed 0.12 in below their feet at its middle; its upper face is lit, the photo being taken from a little above), across the ears' gap (assumed: no view is square to it), carried on between the ears to 1.30 and 3.47 and up to -2.03 (hidden there: assumed), its roll pin's and front holes at the drawing's places, its edges rounded 0.03 (assumed). Its underside's '★BCM' panel (BCM's own photos) isn't drawn.","Its parts kit's controls (the takedown and pivot pins, the selector on SAFE, the bolt catch, the magazine catch's button) are drawn as the Rise kit's, a mil-spec kit whose figures are the Army drawings', on the body's left face at the drawing's width: BCM says its own kit's bolt catch and selector are \"a Mil-Spec AISI8620 investment casting per the USGI TDP for M16/M4\" and publishes no figure of them. Its springs, detents and buffer retainer aren't drawn; its selector is \"Non-Ambi\" (Primary Arms), the lever on the left only.","Not drawn: the roll marks and the serial number (\"★BCM® RIFLE COMPANY / MODEL BCM4 / CAL. MULTI\" on the well's left, \"BRAVO COMPANY MFG. INC. / HARTLAND WISCONSIN / USA\" over the trigger, SEMI and SAFE on both sides), the small hole in the roll, the grip screw's hole and the safety detent's hole in the seat, the buffer retainer's hole, the bore's thread. Edges are broken at 0.02 in (the drawing's \"break corners .02 R\")."],"controls":"rise-lpk","ledger":["bcm-mk2-lower-receiver.bolt_catch_boss_bottom_y","bcm-mk2-lower-receiver.bolt_catch_boss_front_x","bcm-mk2-lower-receiver.bolt_catch_boss_rear_x","bcm-mk2-lower-receiver.bolt_catch_gap_front_x","bcm-mk2-lower-receiver.bolt_catch_gap_rear_x","bcm-mk2-lower-receiver.buffer_axis_above_pin","bcm-mk2-lower-receiver.fence_bottom_y","bcm-mk2-lower-receiver.fence_corner_r","bcm-mk2-lower-receiver.fence_rear_x","bcm-mk2-lower-receiver.fence_top_y","bcm-mk2-lower-receiver.front_ahead_of_pin","bcm-mk2-lower-receiver.front_ear_bottom_y","bcm-mk2-lower-receiver.grip_seat_y","bcm-mk2-lower-receiver.guard_edge_r","bcm-mk2-lower-receiver.guard_front_end_x","bcm-mk2-lower-receiver.guard_rear_end_x","bcm-mk2-lower-receiver.guard_tab_top_y","bcm-mk2-lower-receiver.guard_width","bcm-mk2-lower-receiver.hammer_pin_x","bcm-mk2-lower-receiver.hammer_pin_y","bcm-mk2-lower-receiver.magwell_front_x","bcm-mk2-lower-receiver.magwell_wall_curve_bottom_y_left","bcm-mk2-lower-receiver.magwell_wall_curve_top_y_left","bcm-mk2-lower-receiver.magwell_wall_rear_x","bcm-mk2-lower-receiver.magwell_wall_rear_x_left","bcm-mk2-lower-receiver.magwell_wall_upper_rear_x_left","bcm-mk2-lower-receiver.rear_behind_pin","bcm-mk2-lower-receiver.rear_ear_bottom_y","bcm-mk2-lower-receiver.selector_x","bcm-mk2-lower-receiver.selector_y","bcm-mk2-lower-receiver.tower_front_x","bcm-mk2-lower-receiver.trigger_guard_front_x","bcm-mk2-lower-receiver.trigger_guard_front_y","bcm-mk2-lower-receiver.trigger_guard_rear_x","bcm-mk2-lower-receiver.trigger_guard_rear_y","bcm-mk2-lower-receiver.trigger_pin_x","bcm-mk2-lower-receiver.trigger_pin_y","bcm-mk2-lower-receiver.well_roll_bottom_y","bcm-mk2-lower-receiver.well_roll_crest_out","bcm-mk2-lower-receiver.well_roll_front_x","bcm-mk2-lower-receiver.well_roll_rear_round","bcm-mk2-lower-receiver.well_roll_rear_x","bcm-mk2-lower-receiver.window_front_x","bcm-mk2-lower-receiver.window_rear_x","std.ar15.bolt_catch_boss_out","std.ar15.bolt_catch_plunger_hole_d","std.ar15.bolt_catch_plunger_hole_depth","std.ar15.bolt_catch_plunger_hole_y","std.ar15.bolt_catch_slot_bottom_y","std.ar15.bolt_catch_slot_floor","std.ar15.bolt_catch_slot_front_x","std.ar15.bolt_catch_slot_width","std.ar15.bore_axis_y","std.ar15.buffer_tower_front_x","std.ar15.buffer_tower_od","std.ar15.deck_front_x","std.ar15.deck_y","std.ar15.fcg_pin_hole_d","std.ar15.fcg_pocket_corner_r","std.ar15.fcg_pocket_depth","std.ar15.fcg_pocket_front_x","std.ar15.fcg_pocket_length","std.ar15.fcg_pocket_width","std.ar15.front_lug_slot_width","std.ar15.grip_lug_depth","std.ar15.grip_lug_face_angle","std.ar15.grip_lug_face_from_pin","std.ar15.grip_lug_front_from_rear_face","std.ar15.grip_lug_length","std.ar15.grip_lug_width","std.ar15.grip_seat_below_deck","std.ar15.lower_body_width","std.ar15.mag_catch_boss_edge_r","std.ar15.mag_catch_boss_proud","std.ar15.mag_catch_boss_r","std.ar15.mag_catch_boss_x","std.ar15.mag_catch_cbore_d","std.ar15.mag_catch_cbore_depth","std.ar15.mag_catch_fence_out","std.ar15.mag_catch_hole_d","std.ar15.mag_catch_slot_bottom_y","std.ar15.mag_catch_slot_floor","std.ar15.mag_catch_slot_front_x","std.ar15.mag_catch_slot_h","std.ar15.mag_catch_slot_rear_x","std.ar15.mag_catch_x","std.ar15.mag_catch_y","std.ar15.mag_release_pocket_depth","std.ar15.mag_release_pocket_h","std.ar15.mag_release_pocket_w","std.ar15.magwell_band_bottom_y","std.ar15.magwell_band_front_x","std.ar15.magwell_band_proud","std.ar15.magwell_band_rear_x","std.ar15.magwell_band_side","std.ar15.magwell_box_length","std.ar15.magwell_corner_r","std.ar15.magwell_front_inner_x","std.ar15.magwell_length","std.ar15.magwell_outside_width","std.ar15.magwell_spine_slot_width","std.ar15.magwell_width","std.ar15.pin_spacing","std.ar15.pivot_hole_d","std.ar15.rear_lug_slot_depth","std.ar15.rear_lug_slot_rear_x","std.ar15.rear_lug_slot_width","std.ar15.rear_underside_arc_center_below_seat","std.ar15.rear_underside_arc_center_x","std.ar15.rear_underside_arc_r","std.ar15.rear_underside_round_r","std.ar15.rear_wall_arc_r","std.ar15.receiver_rear_x","std.ar15.safety_detent_boss_below_deck","std.ar15.safety_detent_boss_face","std.ar15.safety_detent_boss_from_rear","std.ar15.safety_detent_boss_length","std.ar15.selector_hole_d","std.ar15.takedown_hole_d","std.ar15.takedown_spotface_d","std.ar15.takedown_spotface_depth","std.ar15.trigger_guard_ear_gap","std.ar15.trigger_guard_ears_width","std.ar15.trigger_guard_front_hole_d","std.ar15.trigger_guard_front_spotface_d","std.ar15.trigger_guard_front_spotface_floor","std.ar15.trigger_guard_rear_hole_d","std.ar15.trigger_pin_x","std.ar15.trigger_slot_front_ahead_of_pin","std.ar15.trigger_slot_length","std.ar15.trigger_slot_width","std.ar15.upper_rear_face_x","std.receiver_extension.milspec_od"]},"profiles":{"side":{"plane":"xy","origin":"the takedown pin centre (the rifle frame origin), +x toward the muzzle","offset":{},"points":[[-0.964,1.504],[-0.935,-0.267],[1.155,-0.892],[1.173,-0.911],[1.18,-1.071],[3.393,-1.039],[3.412,-1.057],[3.434,-2.298],[3.613,-2.281],[6.178,-1.818],[6.197,-1.799],[6.196,-1.732],[6.128,-1.666],[6.089,-1.577],[6.083,-0.645],[6.097,-0.563],[6.169,-0.398],[6.242,-0.315],[6.356,-0.22],[6.542,-0.143],[6.597,-0.086],[6.626,-0.019],[6.609,0.108],[6.537,0.193],[6.365,0.235],[6.223,0.233],[6.148,0.261],[3.561,0.239],[3.539,0.261],[2.331,0.228],[2.308,0.25],[1.742,0.227],[1.667,0.241],[0.169,0.219],[-0.018,0.239],[-0.182,0.296],[-0.295,0.361],[-0.42,0.475],[-0.504,0.586],[-0.565,0.712],[-0.543,1.249],[-0.581,1.278],[-0.581,1.323],[-0.604,1.352],[-0.606,1.501],[-0.707,1.511]],"scaleRefs":["std.ar15.pin_spacing","std.ar15.selector_x","std.ar15.selector_y","std.ar15.trigger_pin_x","std.ar15.trigger_pin_y","std.ar15.hammer_pin_x","std.ar15.hammer_pin_y","std.ar15.trigger_guard_rear_x","std.ar15.trigger_guard_rear_y","std.ar15.trigger_guard_front_x"],"inputs":{"std.ar15.hammer_pin_x":2.771,"std.ar15.hammer_pin_y":-0.375,"std.ar15.pin_spacing":6.375,"std.ar15.selector_x":0.803,"std.ar15.selector_y":-0.466,"std.ar15.trigger_guard_front_x":3.3425,"std.ar15.trigger_guard_rear_x":1.4985,"std.ar15.trigger_guard_rear_y":-2.18,"std.ar15.trigger_pin_x":1.928,"std.ar15.trigger_pin_y":-0.689},"tolerance":0.012,"photo":"references/bcm-mk2-lower-receiver 842fbe8fe0ba (the no-stock complete lower's right side on white: Primary Arms' LRG-RMS-NO-STOCK_01 (2200 x 1467))","method":"luminance < 230, inside [1080, 250, 2140, 900], 4 polygons excluded, closing ×2, largest piece, holes filled; frame from the reviewed holes takedown, pivot, selector, trigger, hammer, guard_rear, guard_front (134.1 px/in, rms 0.030 in over 7 points); origin at the photo's frame; Douglas-Peucker at 0.012 in with the extremes kept: 46 points (IoU 0.996 with the full outline); checks: −x_min 0.964 ± 0.012; y_max 1.511 ± 0.014; top (tooth tops: the edge's max over 0.05 in windows) along x [0.6, 5.8] 0.246 ± 0.022 in vs std.ar15.deck_y 0.2485 ± 0.0015 (confirmed): agrees (tools/trace.py)","via":"harvest","note":"The receiver's right side: the deck, the tower's ring and the walls' sweep down to the deck, the pivot lug under the pivot pin's head, the well with its roll along the top and its lower edge rising toward the front, the front ears down to their foot. Cut along the seat's level from the grip's front to the front ears and along a line above the grip's top behind it: the script builds what is below from the drawing."},"complete":{"plane":"xy","origin":"the takedown pin centre (the rifle frame origin), +x toward the muzzle","offset":{},"points":[[-0.964,1.504],[-0.938,-0.263],[1.155,-0.892],[1.196,-2.461],[1.482,-2.401],[1.541,-2.333],[1.923,-2.432],[2.236,-2.472],[2.534,-2.453],[3.345,-2.292],[3.613,-2.281],[6.178,-1.818],[6.196,-1.732],[6.089,-1.577],[6.097,-0.563],[6.169,-0.398],[6.242,-0.315],[6.356,-0.22],[6.542,-0.143],[6.626,-0.019],[6.609,0.108],[6.537,0.193],[6.148,0.261],[3.561,0.239],[3.433,0.349],[3.279,0.417],[3.254,0.566],[3.153,0.643],[3.041,0.634],[2.949,0.562],[2.914,0.39],[2.946,0.271],[2.927,0.237],[-0.018,0.239],[-0.295,0.361],[-0.504,0.586],[-0.565,0.712],[-0.543,1.249],[-0.604,1.352],[-0.606,1.501],[-0.707,1.511]],"features":{"opening":[[[1.386,-1.713],[1.42,-1.459],[1.522,-1.286],[1.74,-1.13],[1.754,-1.078],[2.074,-1.073],[2.114,-1.221],[2.268,-1.085],[2.827,-1.084],[2.962,-1.127],[3.06,-1.2],[3.223,-1.395],[3.27,-1.521],[3.281,-1.737],[3.201,-1.932],[2.888,-2.194],[2.421,-2.328],[1.965,-2.297],[1.612,-2.086],[1.457,-1.936]]]},"scaleRefs":["std.ar15.pin_spacing","std.ar15.selector_x","std.ar15.selector_y","std.ar15.trigger_pin_x","std.ar15.trigger_pin_y","std.ar15.hammer_pin_x","std.ar15.hammer_pin_y","std.ar15.trigger_guard_rear_x","std.ar15.trigger_guard_rear_y","std.ar15.trigger_guard_front_x"],"inputs":{"std.ar15.hammer_pin_x":2.771,"std.ar15.hammer_pin_y":-0.375,"std.ar15.pin_spacing":6.375,"std.ar15.selector_x":0.803,"std.ar15.selector_y":-0.466,"std.ar15.trigger_guard_front_x":3.3425,"std.ar15.trigger_guard_rear_x":1.4985,"std.ar15.trigger_guard_rear_y":-2.18,"std.ar15.trigger_pin_x":1.928,"std.ar15.trigger_pin_y":-0.689},"tolerance":0.02,"photo":"references/bcm-mk2-lower-receiver 842fbe8fe0ba (the no-stock complete lower's right side on white, as this part is: the receiver with its guard and parts kit (Primary Arms' LRG-RMS-NO-STOCK_01))","method":"luminance < 230, inside [1080, 250, 2140, 900], 4 polygons excluded, closing ×2, largest piece, holes up to 3000 px filled; frame from the reviewed holes takedown, pivot, selector, trigger, hammer, guard_rear, guard_front (134.1 px/in, rms 0.030 in over 7 points); origin at the photo's frame; Douglas-Peucker at 0.02 in with the extremes kept: 41 points (IoU 0.993 with the full outline); checks: −y_min 2.472 ± 0.017; features through the same placement (opening: the trigger's opening: what shows of the backdrop between the rear ears, the body's underside, the front ears and the guard's lit upper face, the trigger's blade taken out (its edges are the ears' curved inner edges and the guard's top)) (tools/trace.py)","via":"harvest","note":"This part's whole silhouette from the right: the receiver, the guard bowed below its ears, the bolt catch's top over the deck. The grip, the tube and the trigger are other slots' parts and aren't in it."},"guard":{"plane":"xy","origin":"the takedown pin centre (the rifle frame origin), +x toward the muzzle","offset":{},"points":[[1.452,-2.092],[1.459,-2.357],[2.124,-2.451],[2.303,-2.456],[2.758,-2.427],[3.356,-2.31],[3.348,-2.009],[3.186,-2.153],[2.897,-2.284],[2.54,-2.348],[2.107,-2.325],[1.786,-2.24],[1.508,-2.088]],"scaleRefs":["std.ar15.pin_spacing","std.ar15.selector_x","std.ar15.selector_y","std.ar15.trigger_pin_x","std.ar15.trigger_pin_y","std.ar15.hammer_pin_x","std.ar15.hammer_pin_y","std.ar15.trigger_guard_rear_x","std.ar15.trigger_guard_rear_y","std.ar15.trigger_guard_front_x"],"inputs":{"std.ar15.hammer_pin_x":2.771,"std.ar15.hammer_pin_y":-0.375,"std.ar15.pin_spacing":6.375,"std.ar15.selector_x":0.803,"std.ar15.selector_y":-0.466,"std.ar15.trigger_guard_front_x":3.3425,"std.ar15.trigger_guard_rear_x":1.4985,"std.ar15.trigger_guard_rear_y":-2.18,"std.ar15.trigger_pin_x":1.928,"std.ar15.trigger_pin_y":-0.689},"tolerance":0.012,"photo":"references/bcm-mk2-lower-receiver 842fbe8fe0ba (BCM's trigger guard as installed, right side (Primary Arms' LRG-RMS-NO-STOCK_01))","method":"manual polygon (16 points picked on the photo); frame from the reviewed holes takedown, pivot, selector, trigger, hammer, guard_rear, guard_front (134.1 px/in, rms 0.030 in over 7 points); origin at the photo's frame; Douglas-Peucker at 0.012 in with the extremes kept: 13 points (IoU 0.962 with the full outline); checks: −y_min 2.456 ± 0.017 (tools/trace.py)","via":"harvest","note":"BCM's polymer guard (BCM-GTG-MOD-0) where it shows between the rear and front ears: bowed down 0.12 in below their feet at its middle, its upper face lit (the photo is taken from a little above)."}},"gaps":[{"what":"BCM's own figures for this receiver: no page gives a dimension or a weight (BCM sells no stripped lower and publishes nothing of the complete one; Primary Arms gives none)","need":"BCM's drawing or spec sheet, or a seller that weighs the stripped forging; until then the Army drawing's figures stand for its interfaces and its weight is worked out from its metal"},{"what":"Where its weight sits: the worked-out weight is put at the middle of what is drawn, though most of the parts kit's steel is in the receiver's left face and its pins","need":"BCM's parts kit weighed piece by piece, or published weights for its pins and controls; they could then be lumps (mass.lumps)"},{"what":"The roll's crest along the well's right top, the guard's width and its hidden ends: assumed (ledger entries marked so)","need":"a view along the receiver from ahead or behind (a seller's or reviewer's), and a view square to the guard from below"},{"what":"Whether this forging is BCM's widebody or its standard lower","need":"a page that says (none of the three pages read does), or a view along the receiver from behind or ahead: none is on file, so it is drawn at the standard's widths"}]},"bcm-mk2-receiver-extension":{"id":"bcm-mk2-receiver-extension","name":"MK2 Receiver Extension","manufacturer":"BCM","sku":"BCM-MK2-RE","url":"https://bravocompanyusa.com/bcm-MK2-receiver-extension/","category":"receiver_extension","description":"The tube of BCM's MK2 recoil mitigation system, about three quarters of an inch longer than a carbine's, with eight stock positions. BCM: \"Machined from 7075T6 and manufactured to Mil-Spec dimensions and specifications\", \"Hard Coat Anodized per Mil-A-8625F, Type III, Class 2\"; \"These tubes should be used with stocks such as USGI, BCM®™, Colt, LMT, SOPMOD, VLTOR, Stag Arms, and others that a made to the Mil-Spec size.\" It takes BCM's MK2 buffer and the M16 rifle action spring: \"These buffer tubes require a M16 rifle action spring and specific BCM MK2 buffer, carbine and rifle buffers will NOT work.\" BCM's kit pages: \"because of the MK2’s longer length some Mil-Spec stocks may not completely collapse closed all the way up to the M4 Lock nut.\"","weight":"bcm-mk2-receiver-extension.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[{"slot":"buffer","parts":["bcm-mk2-buffer-t0"],"says":"BCM, MK2 Receiver Extension: \"These buffer tubes require a M16 rifle action spring and specific BCM MK2 buffer, carbine and rifle buffers will NOT work.\"","source":"https://bravocompanyusa.com/bcm-MK2-receiver-extension/"},{"slot":"buffer_spring","parts":["bcm-rifle-m16-action-spring"],"says":"BCM, MK2 Receiver Extension: \"These buffer tubes require a M16 rifle action spring and specific BCM MK2 buffer, carbine and rifle buffers will NOT work.\" Its kit pages name the spring: \"Mil-Spec M16A4 rifle action spring\".","source":"https://bravocompanyusa.com/bcm-MK2-receiver-extension/"}],"anchors":{"receiver_thread":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the tube axis at the takedown pin's X, +x rearward."},"tube":{"origin":[0,0,0],"x":[1,0,0]},"end":{"origin":["0in - {std.ar15.receiver_rear_x}",0,0],"x":[1,0,0],"note":"On the tube axis at the receiver's rear face (the Army's drawing of the lower), where an end plate bears."},"bore":{"origin":["0in - {std.ar15.upper_rear_face_x}",0,0],"x":[1,0,0],"note":"On the tube axis where a buffer's front face rests with the bolt forward: against the carrier's rear end, which stands at the upper receiver's rear face (the Army's drawings). The buffer and its spring are placed from it."}},"interfaces":{"receiver_thread":{"type":"ar15.buffer_tube_mount","role":"tube","anchor":"receiver_thread","params":{},"flips":false},"tube":{"type":"receiver_extension","role":"tube","anchor":"tube","params":{"profile":"mil-spec","od":"={.tube_od}","positions":8,"step":"={.position_step}"},"flips":false},"extension_end":{"type":"ar15.extension_end","role":"tube","anchor":"end","params":{},"flips":false},"bore":{"type":"ar15.extension_bore","role":"tube","anchor":"bore","params":{},"flips":false}},"materials":{"tube":{"label":"Receiver extension","finish":"anodized","recolorable":true,"color":"placeholder-black","note":"BCM: \"Hard Coat Anodized per Mil-A-8625F, Type III, Class 2\"; black in every photo of it (BCM's two, Primary Arms' one, the kits'). Black anodize is the catalog's stand-in black, not a fitted colour. BCM sells it in black only; recolorable for planning a colour scheme."}},"components":{},"geometry":{"model":"bcm-mk2-receiver-extension.glb","components":{},"approximations":["Its length, its thread's run and the plain band behind it, its rail's ramp and rear chamfer are read on BCM's side photo, scaled by the tube's own thread; its eight holes, the channel they are in, the long slot at the rail's front and the notch at its rear on BCM's photo of its underside, scaled by that length. BCM states no size of it but \"approximately 3/4” longer than carbine\", which the photo bears out.","Its diameter, bore, thread form, the key slot under the thread and the rail's width and depth are the mil-spec carbine extension's (std.receiver_extension.*: the Army's drawing of the rifle's extension and the reference model's carbine one), as BCM says it is made to mil-spec dimensions.","Assumed, no view showing them: the rear wall's thickness and the small hole through it (a mil-spec carbine tube's), and the channel's depth (0.04 in).","Not drawn: the rail's fillets and edge breaks beyond the model's own, any mark, and the relief's tool marks."],"ledger":["bcm-mk2-receiver-extension.tube_od","bcm-mk2-receiver-extension.tube_length","bcm-mk2-receiver-extension.tube_front_behind_pin","bcm-mk2-receiver-extension.thread_length","bcm-mk2-receiver-extension.relief_d","bcm-mk2-receiver-extension.relief_length","bcm-mk2-receiver-extension.rail_ramp_start","bcm-mk2-receiver-extension.rail_ramp_end","bcm-mk2-receiver-extension.rail_rear_chamfer","bcm-mk2-receiver-extension.position_hole_d","bcm-mk2-receiver-extension.position_hole_front_from_face","bcm-mk2-receiver-extension.position_pitch_front","bcm-mk2-receiver-extension.position_pitch_rear","bcm-mk2-receiver-extension.channel_width","bcm-mk2-receiver-extension.channel_depth","bcm-mk2-receiver-extension.front_slot_end_from_face","bcm-mk2-receiver-extension.rear_notch_depth","bcm-mk2-receiver-extension.rear_wall","bcm-mk2-receiver-extension.vent_d"]},"profiles":{},"gaps":[{"what":"Its weight","need":"BCM's figure or a scale: 4.2 oz is worked out from its sizes and 7075's density"},{"what":"Its rear face","need":"A photo of the rear end, square on: its wall and any hole through it are a carbine tube's"},{"what":"Its sizes from BCM","need":"A drawing or BCM's figures: every size here is read on its photos or is the mil-spec carbine tube's"}]},"bcm-pmcr-carbine":{"id":"bcm-pmcr-carbine","name":"PMCR (Polymer M-LOK® Compatible Rail)* Carbine Length-BLACK","manufacturer":"BCM","sku":"BCM-PMCR-CAR-BLK","url":"https://bravocompanyusa.com/bcm-pmcr-polymer-m-lok-rail-carbine-length-black/","category":"handguard","description":"BCM's polymer drop-in hand guard for a carbine-length gas system, in two halves: \"Direct replacement handguard featuring simple \"drop in\" design. For mil-spec, non-free float M4 Carbine-type platforms\"; \"Natural ergonomics; slim, comfortable and lightweight, only 4.48 ounces\"; \"Aggressive textured area for needed traction\"; \"Three, three-hole M-LOK® compatible mounting slots, mounting surfaces (10:30, 1:30, and 6:00 o'clock placements)\"; \"Aluminum heat shield, lessening heat transfer to the handguard and shooter's hand\"; \"Made of an impact and temperature resistant high strength polymer\"; \"Patent Pending design. Made in the USA.\" (BCM). It goes on the rifle's own barrel nut and delta ring and the round cap behind its front sight base: no free-float nut of its own.","weight":"bcm-pmcr-carbine.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"needs":{"slots":["barrel_nut","delta_ring","handguard_cap"],"says":"BCM: \"Direct replacement handguard featuring simple \"drop in\" design. For mil-spec, non-free float M4 Carbine-type platforms\" and \"The PMCR - Carbine will only fit the \"round\" front handguard retaining cap\"; its instructions: \"interlock it to the inside of the front handguard retaining cap\" and \"enough to allow the rear of the PMCR to interface with the Barrel Nut teeth\".","source":"https://bravocompanyusa.com/bcm-pmcr-polymer-m-lok-rail-carbine-length-black/"},"anchors":{"mount":{"origin":["0in - {.rear_x}",0,0],"note":"The receiver's front face on the bore axis, +x toward the muzzle: its rear flanges stand in the delta ring against the ring's lip (std.ar15.slip_ring_front_x ahead of the receiver)."},"mlok":{"origin":["{.mlok_side_slot0_x}",0,0],"note":"On the bore axis at the upper faces' rearmost M-LOK slot's centre (index 0), +x toward the muzzle; the faces are angles about this axis."},"mlok_bottom":{"origin":["{.mlok_bottom_slot0_x}",0,0],"note":"The same axis at the underside's rearmost slot's centre (read on BCM's photo of the lower half from below)."},"cap_seat":{"origin":["{.mounting_length}",0,0],"note":"Its front flange's front end, on the bore axis: what goes into the round hand guard cap (mounting_length, assumed: BCM gives none)."}},"interfaces":{"cap_seat":{"type":"ar15.handguard_front","role":"handguard","anchor":"cap_seat","params":{},"flips":false},"handguard_mount":{"type":"ar15.handguard_mount","role":"handguard","anchor":"mount","params":{"nut":"standard"},"flips":false,"note":"On the rifle's own barrel nut: BCM, \"Direct replacement handguard featuring simple \"drop in\" design. For most mid-length gas system, non-free float carbine-type platforms\"; Primary Arms, \"Because the PMCR clamps onto the existing delta ring rather than requiring a barrel nut swap\". Placed by the standard's delta ring (rear_x): BCM's instructions, \"pull the Delta Ring to the furthest rearward position, enough to allow the rear of the PMCR to interface with the Barrel Nut teeth\"."},"drop_in":{"type":"ar15.drop_in","role":"handguard","params":{"shape":"round"},"flips":false,"note":"BCM (its page, read on the harvested copy): \"The PMCR - Carbine will only fit the \"round\" front handguard retaining cap\"."},"gas_system":{"type":"ar15.gas_system","role":"handguard","params":{"length":"carbine"},"flips":false,"note":"BCM names it \"Carbine Length\" and says it is \"For mil-spec, non-free float M4 Carbine-type platforms\"; its instructions: \"Remove existing carbine handguard\"."},"mlok":{"type":"mlok","role":"slots","anchor":"mlok","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_side_slots}","interval":"={std.mlok.interval}","face_distance":"={.mlok_side_face_distance}","reach_inside":"={.reach_inside}"},"faces":{"right_upper":{"angle":"{.mlok_side_face_angle}","note":"BCM's 1:30 (the rifle's right, +z)"},"left_upper":{"angle":"0 - {.mlok_side_face_angle}","note":"BCM's 10:30"}},"flips":false,"note":"BCM: \"Three, four-hole M-LOK® compatible mounting slots, mounting surfaces (10:30, 1:30, and 6:00 o'clock placements)\". Three in each, counted on BCM's photos."},"mlok_bottom":{"type":"mlok","role":"slots","anchor":"mlok_bottom","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_bottom_slots}","interval":"={std.mlok.interval}","face_distance":"={.mlok_bottom_face_distance}","reach_inside":"={.reach_inside}"},"faces":{"bottom":{"angle":180,"note":"the underside (BCM's 6:00)"}},"flips":false,"note":"BCM's 6:00 row: three slots, counted and placed on BCM's photo of the lower half from below (291dadf219c1)."}},"materials":{"body":{"label":"Hand guard","finish":"polymer","recolorable":true,"color":"placeholder-polymer-black","sheen":"matte","options":{"black":{"label":"Black","finish":"polymer","color":"placeholder-polymer-black","sheen":"matte","sku":"BCM-PMCR-CAR-BLK","source":"https://bravocompanyusa.com/bcm-pmcr-polymer-m-lok-rail-carbine-length-black/"}},"default":"black","note":"Both halves are one colour: \"Made of an impact and temperature resistant high strength polymer\" (BCM); BCM sells the carbine-length in black only (its page and its number, -BLK). Drawn as BCM's black polymer on file is (placeholder-polymer-black, matte, as its grips): a black on polymer isn't fitted, its sheen is what shows."},"heat_shield":{"label":"Heat shield","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"\"Aluminum heat shield, lessening heat transfer to the handguard and shooter's hand\" (BCM): a bare bright sheet inside the lower half, seen through its vents and its six o'clock slots on BCM's photo from below (291dadf219c1). Drawn in the bright metal finish on file; its alloy and temper aren't stated."}},"components":{},"geometry":{"model":"bcm-pmcr-carbine.glb","components":{},"approximations":["One model of both halves (the seam a step along each side, where the narrower lower half stands inside the upper's sides): the two are never apart on a rifle, they come in one box and one colour, and BCM sells them as one product.","Its section about the bore is read on BCM's three photos and assumed between those readings: a flat underside (bottom_half_width, assumed) turning up into faces where the vents are (through their middles, vent_y and vent_z), upright sides to the M-LOK faces (side_top_y), the faces through the slots' centres at the angle the photos show (mlok_side_face_angle: 43° from up, BCM's words 10:30 and 1:30, 45°), and a spine along the top (spine_half_width) from where the faces meet it (spine_vent_y). No view on file looks at an end square on.","Its scale is its own M-LOK slots at the standard's 40 mm pitch on each photo: BCM gives no size. The slots stand nearer the lens than the outline's edges, which may read a percent or two small (length's ±).","Inside: the section less a wall of 0.10 in (wall, assumed: set by BCM's 4.48 oz at the polymer's density on file with its shield; no view shows a section), from a rear wall round the barrel nut to a front wall; ahead of the front wall it is open, over the cap and the front sight base's rear. The front flange that goes into the round cap is a round lip on the front wall (front_flange_od, front_flange_length, mounting_length: assumed, BCM gives none and no photo shows it); why it fits no triangular cap (BCM's words) isn't drawn. The gas tube's way through each end is a notch as wide as the delta ring's own. Ahead of the front wall the inside reaches up into the spine a wall under its top (assumed), and the top of the front end is open round the front sight base's tower from where BCM's photo from above has the spine end (front_notch_x, front_notch_half_width). Where the front sight base stands in its front end with the hand guard seated in its round cap, the inside under the hood is cut clear of BCM's F base model (bcm-front-sight-base-f-750) by 0.02 in all round (base_clearance, assumed): the real part goes on round a front sight base, and how its front end's inside makes room for the base's rear and the foot of its tower no photo on file shows, so the inside there is the base's shape and the clearance, not a reading. The cut is out of sight under its top and inside its sides.","The rear flanges in the delta ring are a ring (rear_collar_od, read), split at each side where the photo sees through between the halves' flanges (rear_collar_gap); their wall is half the body's (assumed). BCM's instructions have them \"interface with the Barrel Nut teeth\": the flanges' inside stands within the nut's toothed flange (1.56 across, std.ar15.barrel_nut_flange_od), in its notches, which aren't drawn as the flanges' own lugs; the two models share a few thousandths of a cubic inch there. The spine runs on over the ring's front as a tab, where the photo has it.","Three M-LOK slots in each upper face and three in the underside at the standard's size and pitch, where BCM's photos have them. Five vents in each lower face, through to the heat shield, where the side photo has them (their width read from below). Along the spine's top two rows of thirteen pockets either side of a middle rib, parted by ribs across, where BCM's photo from above has them, down to the spine's foot, a rim along the outer top edge over them (spine_rim, assumed); every other pocket has a window in the spine's side (where the level side photo has them) and a slit through its floor by the middle rib into the hollow under the spine (the photo from above sees the backdrop through them).","The textured panels are shallow recesses between the side's top and bottom edges (panel_depth, assumed), parted by three ribs where BCM's right side photo has them (2609ad424e86); the stipple itself isn't drawn. The ribbed tab on the lower half's rear stands out from the upper's side by an assumed 0.03 in, its ribs not drawn.","The heat shield is a liner of 0.03 in (assumed) inside the lower half, slotted with the underside's row and the vents. Edges rounded at 0.02 in (moulded; their size isn't read). Not drawn: BCM's star, the M-LOK marks and the K marks."],"ledger":["bcm-pmcr-carbine.length","bcm-pmcr-carbine.width","bcm-pmcr-carbine.height","bcm-pmcr-carbine.mounting_length","bcm-pmcr-carbine.rear_x"]},"profiles":{"side":{"plane":"xy","origin":"its rear end (the spine's tab and the rear flanges, which bear on the delta ring's lip) and the outline's top (the spine's tab over the ring)","offset":{"y":"top_above_axis"},"points":[[0,-0.244],[0.026,-0.265],[0.191,-0.312],[0.218,-0.38],[0.212,-0.456],[0.091,-0.494],[0.065,-0.533],[0.029,-1.045],[0.165,-1.186],[0.177,-1.539],[0.2,-1.557],[0.185,-1.601],[0.091,-1.601],[0.071,-1.615],[0.077,-1.78],[0.112,-2.01],[0.141,-2.098],[0.168,-2.125],[0.25,-2.136],[0.282,-2.204],[0.321,-2.225],[3.775,-2.189],[5.947,-2.201],[6.141,-2.23],[6.259,-2.266],[6.28,-2.286],[6.315,-2.581],[6.356,-2.681],[6.418,-2.731],[6.518,-2.737],[6.591,-2.687],[6.668,-2.486],[6.756,-2.328],[7.021,-1.998],[7.156,-1.786],[7.162,-1.757],[7.139,-1.733],[7.262,-1.563],[7.28,-1.404],[7.274,-1.056],[7.256,-0.897],[7.209,-0.815],[6.827,-0.303],[6.792,-0.068],[6.759,-0.029],[6.73,-0.024],[6.694,-0.035],[6.636,-0.024],[6.259,-0.024],[6.247,-0.035],[6.165,-0.035],[6.135,-0.024],[5.77,-0.024],[5.717,-0.041],[5.241,-0.029],[5.164,-0.047],[5.135,-0.029],[4.958,-0.024],[4.758,-0.024],[4.682,-0.041],[4.67,-0.029],[4.234,-0.029],[4.176,-0.041],[4.105,-0.024],[3.734,-0.024],[3.705,-0.041],[3.652,-0.029],[3.64,-0.041],[3.599,-0.024],[3.234,-0.024],[3.193,-0.041],[3.104,-0.024],[2.634,-0.035],[2.604,-0.024],[2.233,-0.018],[2.175,-0.035],[2.092,-0.018],[1.833,-0.012],[1.598,-0.024],[1.121,-0.012],[1.103,-0.024],[1.009,-0.006],[0.032,0],[0.012,-0.044]],"scaleRefs":["bcm-pmcr-carbine.length"],"inputs":{"bcm-pmcr-carbine.length":7.28},"tolerance":0.01,"photo":"references/bcm-pmcr-carbine 2609ad424e86 (BCM's main photo STKL8995 of the black PMCR carbine-length, assembled, its right side seen level, 1280 x 853)","method":"luminance < 200, closing ×2, largest piece, holes filled; scale from bcm-pmcr-carbine.length = 7.28 in (x-extent 1237 px → 169.9 px/in); origin at x min, y max of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 84 points (IoU 0.997 with the full outline); Its scale is its length as read on the same photo by its three upper M-LOK slots at the standard's 40 mm pitch (length).; checks: −y_min in x [1.0, 5.6] 2.213 ± 0.015; −y_min 2.737 ± 0.017 (tools/trace.py)","via":"harvest","note":"Its M-LOK slots, vents, pockets, panels and the seam are inside the outline; the model cuts them from the ledger. The rear flanges and the spine's tab stand behind the body's rear face (body_rear_x); the front hook is the outline's lowest point."}},"gaps":[{"what":"Any size from BCM: its length, width, height and mounting length","need":"A drawing or a spec table from BCM, a seller's or a reviewer's own measurement"},{"what":"Its front flange (its shape for the round cap, its length) and its inside (the wall, ribs, bosses)","need":"A photo into its front end, or of a half alone from inside"},{"what":"Its section square on (the faces' angle, the spine's sides, the underside)","need":"An end view with a known size in frame"}]},"bcm-pmcr-mid":{"id":"bcm-pmcr-mid","name":"PMCR (Polymer M-LOK® Compatible Rail)* Mid Length-BLACK","manufacturer":"BCM","sku":"BCM-PMCR-MID-BLK","url":"https://bravocompanyusa.com/bcm-pmcr-polymer-m-lok-rail-mid-length-black/","category":"handguard","description":"BCM's polymer drop-in hand guard for a mid-length gas system, in two halves: \"Direct replacement handguard featuring simple \"drop in\" design. For most mid-length gas system, non-free float carbine-type platforms\"; \"Natural ergonomics; slim, comfortable and lightweight, only 5.8 ounces\"; \"Aggressive textured area for needed traction\"; \"Three, four-hole M-LOK® compatible mounting slots, mounting surfaces (10:30, 1:30, and 6:00 o'clock placements)\"; \"Aluminum heat shield, lessening heat transfer to the handguard and shooter's hand\"; \"Made of an impact and temperature resistant high strength polymer\"; \"Patent Pending design. Made in the USA.\" (BCM). It goes on the rifle's own barrel nut and delta ring and the triangular cap behind its front sight base: no free-float nut of its own.","weight":"bcm-pmcr-mid.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"needs":{"slots":["barrel_nut","delta_ring","handguard_cap"],"says":"BCM: \"Direct replacement handguard featuring simple \"drop in\" design. For most mid-length gas system, non-free float carbine-type platforms\" and \"The PMCR - Mid-Length will only fit the M16A1 \"Triangular\" front handguard retaining cap\"; its instructions: \"interlock it to the inside of the front handguard retaining cap\" and \"enough to allow the rear of the PMCR to interface with the Barrel Nut teeth\". Primary Arms: \"Because the PMCR clamps onto the existing delta ring rather than requiring a barrel nut swap\".","source":"https://bravocompanyusa.com/bcm-pmcr-polymer-m-lok-rail-mid-length-black/"},"anchors":{"mount":{"origin":["0in - {.rear_x}",0,0],"note":"The receiver's front face on the bore axis, +x toward the muzzle: its rear flanges stand in the delta ring against the ring's lip (std.ar15.slip_ring_front_x ahead of the receiver)."},"mlok":{"origin":["{.mlok_side_slot0_x}",0,0],"note":"On the bore axis at the upper faces' rearmost M-LOK slot's centre (index 0), +x toward the muzzle; the faces are angles about this axis."},"mlok_bottom":{"origin":["{.mlok_bottom_slot0_x}",0,0],"note":"The same axis at the underside's rearmost slot's centre (read on BCM's photo of the lower half from below)."},"cap_seat":{"origin":["{.mounting_length}",0,0],"note":"Its front flange's front end, on the bore axis: what goes into the triangular hand guard cap (mounting_length, assumed: BCM gives none)."}},"interfaces":{"cap_seat":{"type":"ar15.handguard_front","role":"handguard","anchor":"cap_seat","params":{},"flips":false},"handguard_mount":{"type":"ar15.handguard_mount","role":"handguard","anchor":"mount","params":{"nut":"standard"},"flips":false,"note":"On the rifle's own barrel nut: BCM, \"Direct replacement handguard featuring simple \"drop in\" design. For most mid-length gas system, non-free float carbine-type platforms\"; Primary Arms, \"Because the PMCR clamps onto the existing delta ring rather than requiring a barrel nut swap\". Placed by the standard's delta ring (rear_x): BCM's instructions, \"pull the Delta Ring to the furthest rearward position, enough to allow the rear of the PMCR to interface with the Barrel Nut teeth\"."},"drop_in":{"type":"ar15.drop_in","role":"handguard","params":{"shape":"triangle"},"flips":false,"note":"BCM (its page, read on the harvested copy): \"The PMCR - Mid-Length will only fit the M16A1 \"Triangular\" front handguard retaining cap*\"; and \"*For those that have a round front handguard retaining cap, on the mid-length gas system rifle, Bravo Company offers specialized insert adapters that will allow the PMCR - Mid-Length handguard to fit. Please visit www.bravocompanyusa.com to purchase the inserts.\" The page names no adapter, and none is in the catalog: with a round cap the rule says it doesn't fit."},"gas_system":{"type":"ar15.gas_system","role":"handguard","params":{"length":"mid"},"flips":false,"note":"BCM names it \"Mid Length\" and says it is \"For most mid-length gas system, non-free float carbine-type platforms\"; Primary Arms: \"Gas System Length Mid-Length\"."},"mlok":{"type":"mlok","role":"slots","anchor":"mlok","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_side_slots}","interval":"={std.mlok.interval}","face_distance":"={.mlok_side_face_distance}","reach_inside":"={.reach_inside}"},"faces":{"right_upper":{"angle":"{.mlok_side_face_angle}","note":"BCM's 1:30 (the rifle's right, +z)"},"left_upper":{"angle":"0 - {.mlok_side_face_angle}","note":"BCM's 10:30"}},"flips":false,"note":"BCM: \"Three, four-hole M-LOK® compatible mounting slots, mounting surfaces (10:30, 1:30, and 6:00 o'clock placements)\". Four in each, counted on BCM's three photos."},"mlok_bottom":{"type":"mlok","role":"slots","anchor":"mlok_bottom","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_bottom_slots}","interval":"={std.mlok.interval}","face_distance":"={.mlok_bottom_face_distance}","reach_inside":"={.reach_inside}"},"faces":{"bottom":{"angle":180,"note":"the underside (BCM's 6:00)"}},"flips":false,"note":"BCM's 6:00 row: four slots, counted and placed on BCM's photo of the lower half from below (530bce1646cf)."}},"materials":{"body":{"label":"Hand guard","finish":"polymer","recolorable":true,"color":"placeholder-polymer-black","sheen":"matte","options":{"black":{"label":"Black","finish":"polymer","color":"placeholder-polymer-black","sheen":"matte","sku":"BCM-PMCR-MID-BLK","source":"https://bravocompanyusa.com/bcm-pmcr-polymer-m-lok-rail-mid-length-black/"}},"default":"black","note":"Both halves are one colour: \"Made of an impact and temperature resistant high strength polymer\" (BCM); Primary Arms: \"Black, Matte\". BCM sells the mid-length in black only (its page and its number, -BLK; a cosmetic-blem black is listed beside it). Drawn as BCM's black polymer on file is (placeholder-polymer-black, matte, as its grips): a black on polymer isn't fitted, its sheen is what shows."},"heat_shield":{"label":"Heat shield","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"\"Aluminum heat shield, lessening heat transfer to the handguard and shooter's hand\" (BCM): a bare bright sheet inside the lower half, seen through its vents and its six o'clock slots on BCM's photo from below (530bce1646cf). Drawn in the bright metal finish on file; its alloy and temper aren't stated."}},"components":{},"geometry":{"model":"bcm-pmcr-mid.glb","components":{},"approximations":["One model of both halves (the seam a step along each side, where the narrower lower half stands inside the upper's sides): the two are never apart on a rifle, they come in one box and one colour, and BCM sells them as one product.","Its section about the bore is read on BCM's three photos and assumed between those readings: a flat underside (bottom_half_width, assumed) turning up into faces where the vents are (through their middles, vent_y and vent_z), upright sides to the M-LOK faces (side_top_y), the faces through the slots' centres at the angle the photos show (mlok_side_face_angle: 37° from up, BCM's words 10:30 and 1:30, 45°), and a spine along the top (spine_half_width) from where the faces meet it (spine_vent_y). No view on file looks at an end square on.","Its scale is its own M-LOK slots at the standard's 40 mm pitch on each photo: BCM gives no size. The slots stand nearer the lens than the outline's edges, which may read a percent or two small (length's ±).","Inside: the section less a wall of 0.10 in (wall, assumed: set by BCM's weight at the polymer's density on file with its shield; no view shows a section), from a rear wall round the barrel nut to a front wall; ahead of the front wall it is open, over the cap and the front sight base's rear. The front flange that goes into the triangular cap is a round lip on the front wall (front_flange_od, front_flange_length, mounting_length: assumed, BCM gives none and no photo shows it); a flange made for the triangle fills its corners, which isn't drawn. The gas tube's way through each end is a notch as wide as the delta ring's own. Ahead of the front wall the inside reaches up into the spine a wall under its top (assumed), and the top of the front end is open round the front sight base's tower from where BCM's photo from above has the spine end (front_notch_x, front_notch_half_width). Where the front sight base stands in its front end with the hand guard seated in its triangular cap, the inside under the hood is cut clear of BCM's F base model (bcm-front-sight-base-f-750) by 0.02 in all round (base_clearance, assumed): the real part goes on round a front sight base, and how its front end's inside makes room for the base's rear and the foot of its tower no photo on file shows, so the inside there is the base's shape and the clearance, not a reading. The cut is out of sight under its top and inside its sides.","The rear flanges in the delta ring are a ring (rear_collar_od, read), split at each side where the photo sees through between the halves' flanges (rear_collar_gap); their wall is half the body's (assumed). BCM's instructions have them \"interface with the Barrel Nut teeth\": the flanges' inside stands within the nut's toothed flange (1.56 across, std.ar15.barrel_nut_flange_od), in its notches, which aren't drawn as the flanges' own lugs; the two models share a few thousandths of a cubic inch there. The spine runs on over the ring's front as a tab, where the photo has it.","Four M-LOK slots in each upper face and four in the underside at the standard's size and pitch, where BCM's photos have them. Seven vents in each lower face, through to the heat shield, where the side photo has them (their width read from below). Along the spine's top two rows of seventeen pockets either side of a middle rib, parted by ribs across, where BCM's photo from above has them, down to the spine's foot, a rim along the outer top edge over them (spine_rim, assumed); every other pocket has a window in the spine's side (where the level side photo has them) and a slit through its floor by the middle rib into the hollow under the spine (the photo from above sees the backdrop through them).","The textured panels are shallow recesses between the side's top and bottom edges (panel_depth, assumed), parted by three ribs where BCM's right side photo has them; the stipple itself isn't drawn. The ribbed tab on the lower half's rear stands out from the upper's side by an assumed 0.03 in, its ribs not drawn.","The heat shield is a liner of 0.03 in (assumed) inside the lower half, slotted with the underside's row and the vents. Edges rounded at 0.02 in (moulded; their size isn't read). Not drawn: BCM's star, the M-LOK marks and the K marks."],"ledger":["bcm-pmcr-mid.length","bcm-pmcr-mid.width","bcm-pmcr-mid.height","bcm-pmcr-mid.mounting_length","bcm-pmcr-mid.rear_x"]},"profiles":{"side":{"plane":"xy","origin":"its rear end (the upper rear flange's end, which bears on the delta ring's lip) and the spine's top","offset":{"y":"top_above_axis"},"points":[[0,-0.233],[0.012,-0.259],[0.185,-0.315],[0.205,-0.359],[0.191,-0.462],[0.084,-0.495],[0.058,-0.52],[0.018,-0.763],[0,-1.046],[0.13,-1.186],[0.153,-1.541],[0.145,-1.587],[0.055,-1.589],[0.034,-1.611],[0.047,-1.766],[0.092,-1.986],[0.133,-2.085],[0.163,-2.113],[0.235,-2.122],[0.265,-2.188],[0.311,-2.212],[2.926,-2.181],[7.926,-2.201],[8.114,-2.226],[8.283,-2.275],[8.311,-2.308],[8.34,-2.593],[8.365,-2.665],[8.416,-2.727],[8.479,-2.74],[8.544,-2.736],[8.606,-2.683],[8.673,-2.478],[8.734,-2.362],[9.145,-1.788],[9.156,-1.757],[9.132,-1.741],[9.253,-1.577],[9.28,-1.444],[9.271,-0.957],[9.258,-0.896],[8.839,-0.289],[8.81,-0.075],[8.797,-0.037],[8.769,-0.013],[8.683,-0.027],[8.674,-0.016],[8.265,-0.018],[8.24,-0.034],[8.132,-0.016],[7.768,-0.018],[7.716,-0.038],[7.638,-0.02],[7.258,-0.02],[7.238,-0.038],[7.132,-0.02],[6.752,-0.018],[6.68,-0.038],[6.615,-0.02],[6.3,-0.02],[6.233,-0.022],[6.224,-0.043],[6.201,-0.029],[6.129,-0.036],[6.12,-0.02],[5.738,-0.02],[5.673,-0.038],[5.574,-0.02],[5.228,-0.022],[5.183,-0.036],[5.129,-0.027],[5.12,-0.04],[5.111,-0.02],[4.74,-0.02],[4.648,-0.036],[4.612,-0.022],[4.266,-0.02],[4.124,-0.029],[4.113,-0.045],[4.111,-0.02],[4.079,-0.018],[3.724,-0.018],[3.65,-0.036],[3.589,-0.018],[3.216,-0.018],[3.151,-0.031],[3.092,-0.016],[2.897,-0.013],[2.703,-0.013],[2.665,-0.027],[2.546,-0.013],[2.168,-0.013],[2.148,-0.027],[2.094,-0.011],[1.719,-0.009],[1.633,-0.025],[1.597,-0.011],[1.588,-0.025],[1.577,-0.011],[1.154,-0.011],[1.118,-0.022],[1.067,-0.007],[0.667,-0.004],[0.658,-0.018],[0.592,-0.02],[0.568,-0.002],[0.41,0],[0.132,-0.013],[0.046,-0.004],[0.016,-0.053]],"scaleRefs":["bcm-pmcr-mid.length"],"inputs":{"bcm-pmcr-mid.length":9.28},"tolerance":0.01,"photo":"references/bcm-pmcr-mid 0ff6a5264742 (BCM's gallery photo STKL8992 of the black PMCR mid-length, assembled, its left side seen level, 4268 x 2846)","method":"luminance < 200, closing ×3, largest piece, holes filled; scale from bcm-pmcr-mid.length = 9.28 in (x-extent 4128 px → 444.8 px/in); origin at x min, y max of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 110 points (IoU 0.998 with the full outline); Its scale is its length as read on the same photo by its four upper M-LOK slots at the standard's 40 mm pitch (length).; checks: −y_min in x [1.0, 7.5] 2.203 ± 0.012 in vs bcm-pmcr-mid.height 2.172 ± 0.02 (provisional): agrees; −y_min 2.740 ± 0.015 (tools/trace.py)","via":"harvest","note":"Its M-LOK slots, vents, pads, panels and the seam are inside the outline; the model cuts them from the ledger. The rear flanges and the spine's tab stand behind the body's rear face (body_rear_x); the front hook is the outline's lowest point."}},"gaps":[{"what":"Any size from BCM: its length, width, height and mounting length","need":"A drawing or a spec table from BCM, a seller's or a reviewer's own measurement"},{"what":"Its front flange (its shape for the triangular cap, its length) and its inside (the wall, ribs, bosses)","need":"A photo into its front end, or of a half alone from inside"},{"what":"Its section square on (the faces' angle, the spine's sides, the underside)","need":"An end view with a known size in frame"},{"what":"BCM's insert adapters for a round cap (named by no number)","need":"BCM's page for the inserts, with their number and photos"}]},"bcm-pnt-trigger":{"id":"bcm-pnt-trigger","name":"PNT Trigger Assembly AR15","manufacturer":"BCM","sku":"BCM-PNT-TA1","url":"https://bravocompanyusa.com/bcm-pnt-trigger-assembly-ar15/","category":"trigger","description":"BCM's mil-spec-pattern single-stage trigger group: the PNT (Polished - Nickel - Teflon) trigger and hammer, \"a precision machined Mil-Spec AISI8620 investment casting per the USGI TDP (Mil-Spec) for M16/M4 family of weapons\", the BCM disconnector and \"our impact resistant trigger and hammer pins\" (BCM's page). BCM's text names no springs; its exploded drawing and photos show the hammer, trigger and disconnector springs, its parts-kit list names all three beside the PNT trigger and hammer, and T.REX (\"including springs and trigger pins\") and Alexander's say they are in the assembly. BCM states no pull weight: Primary Arms and AR15Discounts give 5.5 lb, Alexander's about 6. Sellers call it single stage with a curved bow.","weight":"bcm-pnt-trigger.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"fcg":{"origin":[0,0,0],"note":"The trigger pin's axis."},"face":{"origin":["{.face_offset_x}",0,0],"note":"The blade's face, where length of pull is read: the deepest point of its curve, at rest."}},"interfaces":{"fcg":{"type":"ar15.fcg","role":"trigger","anchor":"fcg","params":{"pin_diameter":"small-pin"},"flips":false,"note":"The standard small pins. BCM: \"156/157 holes are honed\" and pins ground \"to ensure compatibility with all MIL SPEC lower receivers built per the USGI TDP\", whose holes are .1560 (a large-pin receiver's are .170); Alexander's: \"Pin Size: .156\\\" / .157\\\" (small pin)\". No BCM page prints .154: that is the Army drawing's pin (pin_diameter)."}},"materials":{"body":{"label":"Trigger","finish":"nickel","recolorable":false,"color":"bcm-pnt-nickel","note":"Electroless nickel with Teflon over the cast steel (BCM: \"An electroless nickel finish is applied\", \"Teflon particles are embedded in the nickel\"); Primary Arms lists the colour as Silver, MidwayUSA and Rifle Supply as Nickel. Sold in the one finish (BCM-PNT-TA1). A satin, slightly warm grey in BCM's photos (96d05cd190c7, dac53da6ba38): drawn as `nickel`, its colour matched to the trigger's own flat in those two. On the assembly BCM pictures, the hammer is the same nickel, the disconnector black, the springs and the two pins a darker grey steel: none of those is drawn (the trigger alone is)."}},"components":{"body":{"label":"Trigger","material":"body"}},"geometry":{"model":"bcm-pnt-trigger.glb","components":{},"approximations":["The trigger alone is drawn. The hammer, the disconnector, the three springs and the two pins the assembly comes with are inside the receiver and aren't drawn.","Its shape is the Army's drawing 8448592 (Trigger), which BCM says it is cast and machined to (\"per the USGI TDP (Mil-Spec) for M16/M4 family of weapons\"): no BCM page gives a dimension. BCM's two straight side photos and its exploded drawing show the same stepped tail, stepped bosses, open slot and blade; they aren't measured from.","At rest where the same drawing's trigger sits in Aero's complete lower (turned 1 degree back about its pin, give or take 0.8): no photo of BCM's shows it installed square to the side.","The blade's face is rounded across on the drawing's .375 radius and its back on the arc Section A-A draws there (0.107 deep where the blade is 0.194 through); along the rest of the blade the back's rounding keeps the flank between the two at that section's width, and runs out over the last eighth of an inch under the block. The face's rounding stops short of the tip (0.07 in), which is left square across with its corners broken, as the drawing's front view has it. The blade's two edges are smoothed within the trace's 0.004 in.","The sweep from the block under the body down to the blade's face is rounded like a prow, its depth run evenly from the face's 0.029 to nearly the block's full round: the drawing's inner lines there aren't read, and no view dimensions it.","Edges are broken at the drawing's .031 (its note 3, for what is left as cast) all over, the machined top and nose included; the slot, the holes, the bosses' steps and the tail's step are cut after that and stay sharp. The bosses' .055 fillets are drawn where the body's side is under them; the slot's .010 corner radii are left out.","The disconnector's slot is open at the tail's rear end, as BCM's exploded drawing and the Army drawing's section have it."],"ledger":["bcm-pnt-trigger.pin_diameter","bcm-pnt-trigger.face_offset_x","bcm-pnt-trigger.shoe_face_x","bcm-pnt-trigger.shoe_width","bcm-pnt-trigger.rest_angle","bcm-pnt-trigger.pivot_hole_d","bcm-pnt-trigger.boss_length","bcm-pnt-trigger.boss_step_length","bcm-pnt-trigger.boss_step_above_axis","bcm-pnt-trigger.boss_fillet_r","bcm-pnt-trigger.slot_width","bcm-pnt-trigger.slot_floor_below_pivot","bcm-pnt-trigger.slot_front_ahead_of_pivot","bcm-pnt-trigger.slot_front_r","bcm-pnt-trigger.spring_hole_d","bcm-pnt-trigger.spring_hole_behind_pivot","bcm-pnt-trigger.spring_hole_floor_below_pivot","bcm-pnt-trigger.tail_step_length","bcm-pnt-trigger.tail_step_depth","bcm-pnt-trigger.blade_face_r","bcm-pnt-trigger.blade_section_length","bcm-pnt-trigger.blade_back_depth","bcm-pnt-trigger.web_from_below_pivot","bcm-pnt-trigger.edge_r","std.ar15.trigger_body_width","std.ar15.trigger_boss_d","std.ar15.trigger_tail_behind_pivot"]},"profiles":{"side":{"plane":"xy","origin":"the pivot hole's centre (the trigger pin's axis), +x toward the muzzle; turned about it to rest (rest_angle)","offset":{},"points":[[-1.208,-0.211],[-1.199,-0.239],[-1.191,-0.244],[-0.363,-0.259],[-0.109,-0.269],[-0.095,-0.284],[-0.097,-0.37],[-0.059,-0.402],[-0.053,-0.415],[-0.054,-0.456],[-0.077,-0.494],[-0.077,-0.506],[-0.09,-0.522],[-0.09,-0.538],[-0.1,-0.55],[-0.104,-0.576],[-0.113,-0.591],[-0.117,-0.626],[-0.127,-0.636],[-0.138,-0.699],[-0.141,-0.883],[-0.135,-0.899],[-0.13,-0.978],[-0.124,-0.985],[-0.097,-1.093],[-0.069,-1.151],[-0.066,-1.17],[-0.033,-1.231],[-0.017,-1.247],[-0.017,-1.272],[-0.006,-1.274],[0.008,-1.288],[0.063,-1.362],[0.127,-1.425],[0.146,-1.435],[0.178,-1.436],[0.199,-1.419],[0.2,-1.381],[0.144,-1.313],[0.104,-1.239],[0.098,-1.204],[0.082,-1.188],[0.07,-1.153],[0.05,-1.054],[0.051,-0.962],[0.045,-0.946],[0.052,-0.931],[0.053,-0.877],[0.067,-0.823],[0.076,-0.814],[0.09,-0.738],[0.1,-0.728],[0.1,-0.716],[0.116,-0.7],[0.123,-0.672],[0.175,-0.596],[0.238,-0.533],[0.322,-0.464],[0.37,-0.433],[0.44,-0.4],[0.487,-0.389],[0.49,-0.189],[0.494,-0.158],[0.512,-0.141],[0.767,-0.147],[0.789,0.031],[0.759,0.036],[0.293,0.044],[0.288,0.03],[0.263,0.007],[0.2,0.001],[0.178,0.008],[0.164,0.023],[0.13,0.096],[0.101,0.133],[0.088,0.133],[0.016,0.163],[-0.013,0.164],[-0.061,0.155],[-0.106,0.134],[-0.143,0.095],[-0.163,0.041],[-0.197,0.011],[-0.225,0.009],[-0.263,0.013],[-0.296,0.043],[-0.297,0.054],[-0.332,0.061],[-0.561,0.062],[-1.119,0.078],[-1.189,0.067],[-1.2,0.059]],"scaleRefs":["bcm-pnt-trigger.tail_at_rest_x","bcm-pnt-trigger.tail_at_rest_y"],"inputs":{"bcm-pnt-trigger.tail_at_rest_x":-1.2023,"bcm-pnt-trigger.tail_at_rest_y":0.021},"tolerance":0.004,"photo":"references/aero-m4e1-lower 1dabf089edf8 (US Army TDP drawing 8448592 (Trigger) rev L (the user's M16 TDP scan, PDF page 43): the side elevation)","method":"luminance < 128, inside [2650, 2815, 3330, 3345], 4 boxes excluded, 2 polygons excluded, closing ×2, the piece at [3051, 3000], holes filled, opening after the fill 9 px ×1, inset 2 px (half the outline's stroke); frame from the reviewed holes pivot, tail (315.2 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.004 in with the extremes kept: 92 points (IoU 0.990 with the full outline); checks: −y_min 1.436 ± 0.007 in vs std.ar15.trigger_blade_below_pivot 1.45 ± 0.02 (confirmed): agrees (tools/trace.py)","via":"user","note":"The trigger's side as the Army drawing has it, at rest: the tail with its roll-off, the reliefs either side of the bosses, the nose and its sear face, the block under the body, the sweep to the blade's face, the blade's two curves and its full-round tip."}},"gaps":[{"what":"The assembly's weight","need":"A weight of the part itself: BCM publishes none, and the sellers' figures are parcels' (4 oz, 0.266 lb) or a default (2 lb). A reviewer's scale reading would do"},{"what":"Where BCM's trigger rests in a lower","need":"A straight side photo of it installed, the receiver's pins in frame: the rest angle is the Aero lower's mil-spec trigger's"},{"what":"The hammer, the disconnector, the springs and the pins","need":"Their Army drawings are in the same scan (8448613, 8448635, 8448593, 8448611, 8448594, 8448609): a later pass, for the exploded view"}]},"bcm-qd-end-plate":{"id":"bcm-qd-end-plate","name":"QD End Plate","manufacturer":"BCM","sku":"BCM-EPM4-QD","url":"https://bravocompanyusa.com/bcm-qd-end-plate/","category":"end_plate","description":"A receiver end plate with a sling socket: the plate between the castle nut and the lower receiver, its lobe carrying a socket for a quick-detach swivel under the receiver extension. BCM: \"BCM® Receiver End Plate with socket for Quick Disconnect (QD) swivel.\" \"Machined from steel, and easily accommodates staking.\" T.REX ARMS, which sells it: \"Accepts standard QD push-button sling swivels.\" \"Install with the Star Logo out.\"","weight":"bcm-qd-end-plate.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"end":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the tube axis at the plate's front face, against the receiver's rear face, +x rearward."},"nut_seat":{"origin":["{.thickness}",0,0],"x":[1,0,0],"note":"The plate's rear face (the star's), where the castle nut bears."}},"interfaces":{"extension_end":{"type":"ar15.extension_end","role":"fitting","anchor":"end","params":{},"flips":false},"nut_seat":{"type":"ar15.end_plate_seat","role":"plate","anchor":"nut_seat","params":{},"flips":false}},"materials":{"plate":{"label":"End plate","finish":"phosphate","recolorable":false,"color":"steel-phosphate-dark","note":"Steel (BCM: \"Machined from steel\"); Primary Arms: \"a BCM star marking and corrosion-resistant black finish\". Which finish isn't said: a matte dark grey in BCM's own photos and black in Primary Arms', drawn as a dark phosphate. The star on its rear face isn't drawn."}},"components":{},"geometry":{"model":"bcm-qd-end-plate.glb","components":{},"approximations":["Its face is Primary Arms' straight face-on photo of it, scaled by the hole every end plate has for the extension's thread (a mil-spec plate's, from the reference model): BCM states no size. At that scale its socket's opening is 0.37 in and its socket sits where a plain plate has its boss, which is what each has to be.","The socket is a plain collar through the plate with a plain bore: its length each side of the plate is read on one near edge-on photo, to ± 0.03 in; the groove inside it that a swivel's balls lock in, the knurl where it is pressed into the plate and the chamfer at its mouth aren't drawn. On the front its diameter isn't read, and is drawn as the collar's.","The key in its hole that rides in the extension's slot is the standard's, as BCM's plain plate has it. Not drawn: the star, and the staking points.","Its collar stands 0.1 in out of its front face, into the receiver's rear face where the takedown pin's detent spring is: no lower in the catalog has that recess drawn, so the two models share that much."],"ledger":["bcm-qd-end-plate.thickness","bcm-qd-end-plate.height","bcm-qd-end-plate.top_above_axis","bcm-qd-end-plate.socket_below_axis","bcm-qd-end-plate.socket_od","bcm-qd-end-plate.socket_proud_rear"]},"profiles":{"face":{"plane":"zy","origin":"the plate's top edge, centred on the ring; offset up to its height above the tube axis","offset":{"y":"top_above_axis"},"points":[[-0.667,-0.696],[-0.636,-0.861],[-0.561,-1.037],[-0.417,-1.69],[-0.383,-1.784],[-0.312,-1.886],[-0.211,-1.967],[-0.084,-2.015],[0.023,-2.023],[0.138,-1.998],[0.232,-1.95],[0.325,-1.865],[0.379,-1.776],[0.561,-1.037],[0.648,-0.822],[0.667,-0.64],[0.648,-0.506],[0.617,-0.412],[0.544,-0.281],[0.461,-0.184],[0.359,-0.104],[0.23,-0.04],[0.1,-0.004],[0,0],[-0.044,0],[-0.167,-0.019],[-0.284,-0.061],[-0.415,-0.142],[-0.502,-0.224],[-0.575,-0.325],[-0.632,-0.446],[-0.663,-0.581]],"scaleRefs":["bcm-qd-end-plate.height"],"inputs":{"bcm-qd-end-plate.height":2.023},"tolerance":0.01,"photo":"references/bcm-qd-end-plate f9569188119d (Primary Arms' BCM-EPM4-QD_02, straight face-on, 2000 x 1333)","method":"luminance < 200, closing ×2, largest piece, holes filled; scale from bcm-qd-end-plate.height = 2.023 in (y-extent 969 px → 479.0 px/in); origin at x center, y max of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 32 points (IoU 0.994 with the full outline) (tools/trace.py)","via":"harvest","note":"Its ring's hole and its socket's bore are inside the outline, filled: the model bores both. Seen from the star's side, which is its rear face; the outline is the same from either."}},"gaps":[{"what":"Its sizes","need":"BCM's figures, or a photo of it with scale: every size here is read on photos scaled by the hole for the extension"}]},"bcm-receiver-extension":{"id":"bcm-receiver-extension","name":"Milspec Carbine Receiver Extension (Buffer Tube) 6 Position","manufacturer":"BCM","sku":"BCM-Milspec-RE","url":"https://bravocompanyusa.com/bcm-milspec-carbine-receiver-extension-buffer-tube-6-position/","category":"receiver_extension","description":"BCM's carbine receiver extension, the buffer tube, with six stock positions: \"machined from 7075T6 and manufactured to Mil-Spec dimensions and specifications\", \"Hard Coat Anodized per Mil-A-8625F, Type III, Class 2\". The stock rides on it, and the buffer and the action spring are inside it. BCM: \"Mil-Spec receiver extensions have a slightly smaller dimension where the stock slides on.\"","weight":"bcm-receiver-extension.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"receiver_thread":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the tube axis at the takedown pin's X, +x rearward."},"tube":{"origin":[0,0,0],"x":[1,0,0]},"end":{"origin":["0in - {std.ar15.receiver_rear_x}",0,0],"x":[1,0,0],"note":"On the tube axis at the receiver's rear face (the Army's drawing of the lower), where an end plate bears."},"bore":{"origin":["0in - {std.ar15.upper_rear_face_x}",0,0],"x":[1,0,0],"note":"On the tube axis where a buffer's front face rests with the bolt forward: against the carrier's rear end, which stands at the upper receiver's rear face (the Army's drawings). The buffer and its spring are placed from it."}},"interfaces":{"receiver_thread":{"type":"ar15.buffer_tube_mount","role":"tube","anchor":"receiver_thread","params":{},"flips":false},"tube":{"type":"receiver_extension","role":"tube","anchor":"tube","params":{"profile":"mil-spec","od":"={.tube_od}","positions":6,"step":"={.position_step}"},"flips":false},"extension_end":{"type":"ar15.extension_end","role":"tube","anchor":"end","params":{},"flips":false},"bore":{"type":"ar15.extension_bore","role":"tube","anchor":"bore","params":{},"flips":false}},"materials":{"tube":{"label":"Receiver extension","finish":"anodized","recolorable":true,"color":"placeholder-black","note":"Hard coat anodized per MIL-A-8625F Type III Class 2 (BCM sells black). Recolorable for planning a colour scheme: other colours mean another maker's tube (e.g. Aero's ODG) or Cerakote."}},"components":{},"geometry":{"model":"bcm-receiver-extension.glb","components":{},"approximations":[],"ledger":["bcm-receiver-extension.tube_od","bcm-receiver-extension.tube_front_behind_pin","bcm-receiver-extension.tube_length","bcm-receiver-extension.position_step","bcm-receiver-extension.position_hole_d","bcm-receiver-extension.position_hole_rear_from_rear"]},"profiles":{},"gaps":[]},"bcm-rifle-m16-action-spring":{"id":"bcm-rifle-m16-action-spring","name":"Rifle M16 Action Spring","manufacturer":"BCM","sku":"SPRING-RIFLE-M16-ACTION","url":"https://bravocompanyusa.com/rifle-m16-action-spring/","category":"buffer_spring","description":"The M16 rifle's action spring, longer than a carbine's and with more coils. BCM: \"Action spring for M16, M16A1, M16A2, M16A3, M16A4. For use with a full size M16 Rifle buffer and full size rifle M16 receiver extension.\" It is also the spring of BCM's MK2 recoil mitigation system: its MK2 kits list a \"Mil-Spec M16A4 rifle action spring\" with \"more spring coils than M4 carbine\", and its MK2 buffer \"ONLY works in conjunction with the BCM MK2 Receiver Extension (BCM part #BCM-MK2-RE) and the Mil-Spec Rifle M16 Action Spring (BCM part # SPRING-RIFLE-M16-ACTION)\".","weight":"bcm-rifle-m16-action-spring.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[{"slot":"receiver_extension","parts":["bcm-mk2-receiver-extension","vltor-a5-receiver-extension"],"says":"BCM, of this spring: \"For use with a full size M16 Rifle buffer and full size rifle M16 receiver extension.\" BCM's MK2 tube: \"These buffer tubes require a M16 rifle action spring\"; VLTOR's A5: \"Always use A5-specific buffers and a rifle-length spring.\"","source":"https://bravocompanyusa.com/rifle-m16-action-spring/"}],"anchors":{"bore":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the receiver extension's axis where a buffer's front face rests, +x rearward."}},"interfaces":{"bore":{"type":"ar15.extension_bore","role":"buffer","anchor":"bore","params":{},"flips":false}},"materials":{"spring":{"label":"Spring","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"The Army's drawing: \"WIRE, STAINLESS STEEL, TYPE 631, (17-7PH) COLD DRAWN, ASTM A313\", \"PRECIPITATION HEAT TREAT AFTER FORMING TO CONDTN CH 900\". A pale silver with a straw tint in both of BCM's photos of it (b7afddafe667, da2d35d9e02d), where BCM's carbine spring is a bronze brown. BCM's own photo reads #a59a89 (the wire's pixels darker than 200, less the darkest tenth and the brightest 15%); fitted under `steel` in the hero direction, drawn apart, the colour ran to white (#f3eed7, rendering #9e9a89) and wasn't kept: a bright metal, its finish type is its look (it renders #838383 there)."}},"components":{},"geometry":{"model":"bcm-rifle-m16-action-spring.glb","components":{},"approximations":["Drawn as it is in BCM's MK2 tube: held between the MK2 buffer's head and the tube's rear wall, 7.68 in long, where it is 12.50 in free (the Army's drawing) and 8.19 in the M16 rifle's own extension. Its wire (.072 in) and outside diameter (.940) are the Army's drawing's; its 43 and a half coils are counted on BCM's two photos of it (the drawing's 44 REF).","Its end coils are closed; the one coil at each end that the Army's drawing reduces to .900 isn't.","In any other tube it is drawn at the same length: in a carbine tube it would stand 0.63 in out of the rear (it isn't made for one)."],"ledger":["bcm-rifle-m16-action-spring.wire_d","bcm-rifle-m16-action-spring.od","bcm-rifle-m16-action-spring.coils","bcm-rifle-m16-action-spring.free_length","bcm-rifle-m16-action-spring.installed_length"]},"profiles":{},"gaps":[{"what":"Its weight","need":"BCM's figure or a scale: 2.2 oz is worked out from its wire's length and steel's density"}]},"bcm-stock-mod-0":{"id":"bcm-stock-mod-0","name":"Stock - Mod 0","manufacturer":"BCM","sku":"BCM-GFS-MOD-0-BLK","url":"https://bravocompanyusa.com/bcm-stock-mod-0-black/","category":"stock","description":"BCM's minimalist carbine stock (\"The strongest light-weight polymer stock available for your mil-spec receiver extension\"): a slim cheek round the tube with a large lever under it, a rear body with an ambidextrous QD socket and a web sling slot, a rubber butt pad. Six positions on a mil-spec receiver extension only. BCM states no size or weight; a seller gives 6.75 x 4.9 x 1.67 in (by BCM's patent section and its photo of the stock on a rifle it is 6.66 in long), sellers 8.2 to 8.4 oz.","weight":"bcm-stock-mod-0.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"butt":{"origin":[0,0,0],"note":"The butt's plane on the tube axis: the part frame's origin. Overall length and length of pull end here."},"tube":{"origin":["{.butt_behind_pin_pos1}",0,0],"x":[-1,0,0],"note":"Stock frame: origin on the tube axis in the plane of the butt, +x forward. At position 1 this anchor sits at the takedown pin's X."}},"interfaces":{"tube":{"type":"receiver_extension","role":"stock","anchor":"tube","params":{"profile":"mil-spec"},"flips":false,"note":"BCM's shop page: \"The strongest light-weight polymer stock available for your mil-spec receiver extension is here!\" Its installation guide (Rev. 9/14): \"This stock is compatible ONLY with Mil-Spec AR-style platforms.\" and \"If the stock does not fit, confirm that the tube is Mil-Spec diameter.\" No commercial-spec version is listed anywhere on file."}},"materials":{"body":{"label":"Stock body","finish":"polymer","recolorable":true,"color":"placeholder-polymer-black","sheen":"matte","options":{"black":{"label":"Black","finish":"polymer","color":"placeholder-polymer-black","sheen":"matte","sku":"BCM-GFS-MOD-0-BLK","source":"https://bravocompanyusa.com/bcm-stock-mod-0-black/"},"fde":{"label":"Flat Dark Earth","finish":"polymer","color":"bcm-fde","sheen":"matte","sku":"BCM-GFS-Mod-0-FDE","source":"https://bravocompanyusa.com/bcm-stock-assembly-flat-dark-earth/"},"fg":{"label":"Foliage Green","finish":"polymer","color":"bcm-foliage-green","sheen":"matte","sku":"BCM-GFS-MOD-0-FG","source":"https://dirtybirdusa.com/products/bcmgunfighter-stock-mod-0/"},"wg":{"label":"Wolf Gray","finish":"polymer","color":"bcm-wolf-gray","sheen":"matte","sku":"BCM-GFS-MOD-0-WG","source":"https://dirtybirdusa.com/products/bcmgunfighter-stock-mod-0/"}},"default":"black","note":"BCM: \"Available in Black, Flat Dark Earth, Foliage Green, and Wolf Gray.\" Its shop has a page for Black and for Flat Dark Earth (BCM-GFS-Mod-0-FDE); Dirty Bird and AR15Discounts list all four numbers (BCM-GFS-MOD-0-FG, -WG). The lever under the cheek is the body's colour in every one. Black is the catalog's stand-in polymer black: BCM's black reads as black in its sellers' photos (#22211c on Primary Arms'), and a black isn't fitted. Flat Dark Earth is the colour of BCM's own photos of 2020: its distributor's older picture of the stock (BCM-GFS-MOD-0-FDE_1_HR) is a far lighter tan, #e3d1a8, with a tan pad."},"buttpad":{"label":"Butt pad","finish":"rubber","recolorable":false,"color":"placeholder-polymer-black","follows":{"slot":"body","options":{"fde":{"finish":"rubber","color":"bcm-pad-gray"},"fg":{"finish":"rubber","color":"bcm-foliage-green-rubber"},"wg":{"finish":"rubber","color":"bcm-pad-gray"}}},"note":"Rubber (Wing Tactical: \"Integrated color matched rubber butt pad\"). Black on the black stock. On the Flat Dark Earth stock a dark grey, not the body's colour: BCM's own four photos of 2020, Wing's, Dirty Bird's (BCM-GFS-MOD-0-FDE_2_HR). On the Wolf Gray stock the same dark grey in the distributor's later photos (GunGear's BCM-GFS-MOD-0-WG_2_HR and _3_HR); its earlier one (WG_1_HR) and BCM's brochure have a pad of the body's grey, as the earlier Flat Dark Earth picture (FDE_1_HR) has a tan one: the pad was the stock's colour at first and is dark grey on what BCM has photographed since. On the Foliage Green stock the body's green, by the one photograph of that colour on file (Bauer Precision's BCM-GFS-MOD-0-FG_1_HR, of the earlier kind): a Foliage Green stock made since may have the dark grey pad, and no photo on file shows one."},"qd":{"label":"QD socket","finish":"phosphate","recolorable":false,"color":"steel-phosphate-charcoal","note":"The socket's steel cup: a matte dark grey in every colour of stock (BCM's Flat Dark Earth photos, where it reads #383738 and mottled like a phosphate; Wing's and Dirty Bird's; dark on the Foliage Green and the Wolf Gray stock in the distributor's photos). BCM states neither its steel nor its finish: phosphate by its look, not by a sentence."}},"components":{"body":{"label":"Stock body","material":"body"},"buttpad":{"label":"Butt pad","material":"buttpad"},"qd":{"label":"QD socket","material":"qd"}},"geometry":{"model":"bcm-stock-mod-0.glb","components":{},"approximations":["Visual hull of the traced side photo (Primary Arms, the black stock straight from the right, scaled by the published 4.9 in height and brought along its length to the measured 6.66 in: the photo's two ends are the stock's near edges, nearer the lens than its top and toe, and read 2.5% long) and the rear view of BCM's patent (US 9,109,855 B1, FIG. 3B, scaled by the same height; its width over the two wings then reads the published 1.67 in). The rear view's section (1.46 in across the body) holds behind the rear body's front edge: the side wings' front edge and, below the wings, the lever's rear ramp, and above the wings only the block over the pad's plate. Ahead of it the cheek round the tube is drawn at its own width (2026-10-19): 1.33 in, read on the stock's front face against the bore's mouth in Wing's photo from ahead, its section the rear view's narrowed about the middle in proportion (a round top and flat sides, the bore walled all round), its top the side outline's, 0.07 in under the rear body's; the lever under it is the cheek's width, as the front photos have it. The strut is still as wide as the butt, which it isn't (its ribbed underside is a narrow strip): no width is read for it. A utility patent's figures aren't held to scale: this one's proportions are the published ones.","The rear body's two side wings are the side photo's outline of them along the stock and, across it, the ear the patent's rear view draws each side (2026-10-13; they had stood square at the full width, a slab): out of the body's side from the wing's upper edge, 0.65 in below the top, in a quarter round to the published width (1.67 in) at 0.98 in, and back into the side by 1.65 in in a straight ease, which the figure's outline follows within about 0.01 in. The same outline is held along the wing's whole length, and the wing ends square at its front edge. Below 1.65 in the wing's lower edge in the side photo, with its arch over the QD socket, is the upper wall of the recessed panel under it.","The bore for the receiver extension is cut at the mil-spec tube's diameter with the channel for its indexing rail under it (the standard's width and depth), back to the stock's end wall, 0.77 in ahead of the butt in the patent's section (the tube's rear face stands against it when the stock is collapsed); the rubber butt pad is its own part behind its seam; the QD socket, the web sling slot and the installation rod's hole are cut through. The script asks an edge break of 0.03 in of every piece and the bevel gives almost none (it is held to the shortest edge of the mesh, and the ribs' are a hundredth of an inch): edges are square but for the lever's seam.","The lever under the cheek is its own piece along its seam in the side photo, as wide as the cheek and flush with it (since 2026-10-19; before, both were the body's width). Along its rear ramp the rear body stands proud of it by the step between the two widths, which is the seam there. Along its top the seam is a cut of the two pieces' edge break, a V 0.06 in across and 0.03 deep each side of the stock (2026-10-13): left to the bevel, the body's edge there was broken 0.0003 in and the lever's 0.003, a seam a tenth of a pixel wide that the page drew as dashes. On the stock the seam is a line about a hundredth of an inch wide under the cheek's rounded edge: the V is the least a page draws whole. The lever's own shape (its faceted underside, the tab at its rear, its release) isn't drawn.","The strut's underside is ribbed across at the pitch (0.067 in) and the depth (0.013 in) its teeth show in the side photo; the pad's face is ribbed in chevrons at the angle the patent's rear view draws (36.5°), from where they begin under the star, at the pitch (0.114 in) and depth (0.011 in) the pad's teeth show in the side photo. Each groove is a V half a pitch wide; the depths are an edge's, and the ribs may stand higher. The chevrons run to the pad's edges at every height: the star above them, and the ribs it cuts short, aren't drawn.","The recessed panel round the QD socket and the pocket in the strut's triangle are cut in each side, inside outlines picked on the side photo down the middle of each wall's band (2026-10-13). Their depths are assumed, 0.05 in and 0.1 in from the body's side: no view on file is square across either, and BCM's photos from behind and below show the triangle's pocket a good deal deeper than it is drawn, with a thin web between its two sides. The walls are drawn square (on the stock they lean or are rounded: bands 13 to 26 px wide in the side photo); the triangle's floor follows the body's taper to the toe. Round them the frame stands at the body's side: the band beside the pad, the bar over the sling slot, the strut's face (0.16 to 0.19 in across) and the leg ahead of the panel.","The QD socket's cup is its own part round the socket's hole (its rim placed by the dark ring on Wing's Flat Dark Earth stock), flush with its panel's floor and drawn as one tube across the stock: the two sockets' depth isn't on file, nor whether the cup stands off the floor.","Not drawn: the cheek's facets (the line along its side and the chamfer at its front), the VBOST tab's detail, the stippling under the lever, the lock pin's release in the lever's underside, the markings.","Its seat on the tube is read on BCM's brochure photo of it on a rifle, four steps out, between the receiver's pins (33.7 px/in), less the four steps: ± 0.07 in. Wing's photo of it on a lower and a reviewer's lengths of pull agree within 0.05 in; BCM's patent section, with a generic tube, would seat it 0.12 to 0.26 in further back."],"ledger":["bcm-stock-mod-0.length","bcm-stock-mod-0.height","bcm-stock-mod-0.width","bcm-stock-mod-0.body_width","bcm-stock-mod-0.cheek_width","bcm-stock-mod-0.tube_axis_below_top","bcm-stock-mod-0.butt_behind_tube_rear_pos1","bcm-stock-mod-0.butt_behind_pin_pos1","bcm-stock-mod-0.strut_rib_pitch","bcm-stock-mod-0.strut_rib_depth","bcm-stock-mod-0.pad_rib_pitch","bcm-stock-mod-0.pad_rib_depth","bcm-stock-mod-0.pad_rib_angle","bcm-stock-mod-0.pad_rib_top","bcm-stock-mod-0.wing_top_below_top","bcm-stock-mod-0.wing_widest_below_top","bcm-stock-mod-0.wing_end_below_top","bcm-stock-mod-0.qd_panel_recess_depth","bcm-stock-mod-0.triangle_recess_depth"]},"profiles":{"side":{"plane":"xy","origin":"rearmost point of the butt pad (x) and the top edge at its highest, the rear body's top (y); the photo shows the top level, so the tube axis is horizontal","offset":{"y":"tube_axis_below_top"},"points":[[0,-0.421],[0.008,-0.637],[0.1,-1.472],[0.116,-1.508],[0.112,-1.607],[0.128,-1.659],[0.124,-1.739],[0.14,-1.791],[0.136,-1.871],[0.152,-1.923],[0.148,-2.003],[0.164,-2.055],[0.16,-2.139],[0.176,-2.19],[0.172,-2.274],[0.188,-2.326],[0.184,-2.41],[0.2,-2.458],[0.196,-2.542],[0.212,-2.59],[0.208,-2.678],[0.224,-2.722],[0.244,-3.049],[0.26,-3.093],[0.268,-3.281],[0.288,-3.341],[0.296,-3.524],[0.327,-3.684],[0.323,-3.748],[0.339,-3.788],[0.347,-3.948],[0.367,-4.003],[0.375,-4.155],[0.395,-4.203],[0.399,-4.275],[0.423,-4.319],[0.423,-4.367],[0.451,-4.411],[0.455,-4.499],[0.483,-4.515],[0.487,-4.571],[0.575,-4.822],[0.633,-4.876],[0.761,-4.88],[0.789,-4.9],[0.813,-4.888],[0.984,-4.888],[1.118,-4.778],[1.873,-3.652],[1.873,-3.632],[1.905,-3.604],[1.909,-3.576],[1.981,-3.492],[2.021,-3.408],[2.097,-3.317],[2.093,-3.301],[2.204,-3.157],[2.204,-3.133],[2.24,-3.105],[2.24,-3.077],[2.28,-3.041],[2.276,-3.005],[2.378,-2.895],[2.486,-2.927],[2.528,-2.961],[2.556,-3.017],[2.544,-3.125],[2.558,-3.147],[2.59,-3.151],[2.616,-3.133],[2.759,-2.777],[2.809,-2.712],[2.829,-2.763],[2.909,-2.763],[2.993,-2.756],[3.025,-2.736],[3.664,-2.68],[3.852,-2.676],[4.543,-2.608],[4.794,-2.604],[4.942,-2.576],[4.994,-2.588],[5.781,-2.52],[5.932,-2.468],[6.695,-2.109],[6.713,-2.083],[6.761,-1.779],[6.753,-1.747],[6.693,-1.711],[6.739,-1.685],[6.765,-1.643],[6.825,-0.617],[6.793,-0.337],[6.753,-0.154],[6.723,-0.104],[6.615,-0.068],[1.927,-0.064],[0.972,-0.076],[0.865,-0.072],[0.789,-0.004],[0.697,0],[0.373,-0.012],[0.206,-0.044],[0.154,-0.068],[0.088,-0.126],[0.036,-0.206],[0.008,-0.302]],"features":{"through":[[[1.43,-2.027],[1.454,-1.951],[1.5,-1.897],[1.571,-1.861],[1.619,-1.861],[1.695,-1.897],[1.745,-1.951],[1.769,-2.011],[1.769,-2.091],[1.745,-2.15],[1.695,-2.204],[1.643,-2.228],[1.575,-2.224],[1.504,-2.192],[1.458,-2.143],[1.434,-2.087]],[[0.847,-2.71],[0.859,-2.666],[0.897,-2.64],[2.234,-2.564],[2.302,-2.568],[2.336,-2.614],[2.314,-2.668],[2.238,-2.696],[0.917,-2.767],[0.873,-2.752]],[[3.818,-2.166],[3.868,-2.113],[3.928,-2.117],[3.954,-2.158],[3.954,-2.214],[3.848,-2.256],[3.822,-2.222]]],"buttpad":[[[-0.641,0.25],[0.294,0.25],[0.302,-0.03],[0.341,-0.589],[0.393,-1.188],[0.449,-1.787],[0.529,-2.386],[0.601,-2.985],[0.669,-3.584],[0.729,-4.183],[0.789,-4.782],[0.805,-5.162],[-0.641,-5.162]]],"wing":[[[0.341,-0.649],[2.334,-0.649],[2.422,-0.689],[2.462,-0.781],[2.482,-1.188],[2.522,-1.587],[2.562,-1.979],[2.194,-1.979],[2.083,-1.807],[1.895,-1.687],[1.595,-1.651],[1.296,-1.687],[1.108,-1.807],[0.976,-1.979],[0.477,-1.979],[0.449,-1.787],[0.393,-1.188],[0.349,-0.709]]],"qd_cup":[[[1.923,-2.039],[1.916,-2.103],[1.898,-2.164],[1.868,-2.221],[1.827,-2.27],[1.777,-2.311],[1.721,-2.341],[1.659,-2.36],[1.595,-2.366],[1.531,-2.36],[1.47,-2.341],[1.413,-2.311],[1.364,-2.27],[1.323,-2.221],[1.293,-2.164],[1.274,-2.103],[1.268,-2.039],[1.274,-1.975],[1.293,-1.913],[1.323,-1.857],[1.364,-1.807],[1.413,-1.766],[1.47,-1.736],[1.531,-1.718],[1.595,-1.711],[1.659,-1.718],[1.721,-1.736],[1.777,-1.766],[1.827,-1.807],[1.868,-1.857],[1.898,-1.913],[1.916,-1.975]]],"lever":[[[2.785,-2.75],[3.177,-1.855],[5.265,-1.855],[6.587,-1.699],[6.907,-1.699],[6.907,-2.865],[2.825,-2.865]]],"strut_ribs":[[[2.194,-3.009],[1.156,-4.431],[1.056,-4.363],[2.099,-2.937]]],"qd_panel":[[[0.657,-1.947],[1.108,-1.947],[1.204,-1.907],[1.276,-1.843],[1.388,-1.731],[1.492,-1.683],[1.595,-1.667],[1.699,-1.683],[1.803,-1.731],[1.915,-1.843],[1.987,-1.907],[2.043,-1.947],[2.498,-1.947],[2.518,-2.522],[0.657,-2.522]]],"triangle":[[[0.797,-2.965],[2.043,-2.913],[2.083,-2.937],[2.071,-2.985],[1.987,-3.105],[1.056,-4.583],[1.004,-4.654],[0.976,-4.646],[0.964,-4.602]]]},"scaleRefs":["bcm-stock-mod-0.height"],"inputs":{"bcm-stock-mod-0.height":4.9},"tolerance":0.01,"photo":"references/bcm-stock-mod-0 a9e871874f14 (Primary Arms BCM-GFS-MOD-0-BLK_00.jpg, straight right side on white, 2000 x 1333)","method":"luminance < 235, closing ×2, largest piece, holes filled; scale from bcm-stock-mod-0.height = 4.9 in (y-extent 1227 px → 250.4 px/in); origin at x min, y max of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 107 points (IoU 0.998 with the full outline); Scaled by the height alone: the outline's length then reads 6.82 in, 2.5% over the measured 6.66 (the ledger's length: BCM's patent section and its photo of the stock on a rifle). The outline's two ends are the stock's near edges, 0.73 in nearer the lens than the top and the toe, which lie on its middle: from about 30 in that is the 2.5%. The model takes the outline at this scale and the measured length along x.; checks: width 6.825 ± 0.012 in vs bcm-stock-mod-0.length 6.657 ± 0.04 (conflict): DISAGREES; features through the same placement (through: The QD socket (through both sides), the web sling slot, and the hole for the installation rod.; buttpad: Behind the rubber pad's seam: a faint line on the black photo, placed by the pad's dark band on Wing's FDE stock.; wing: The rear body's side wing, which laps over the main body's side: its top edge, its rounded front corner, its front edge, and the arch cut in its lower edge round the QD socket.; qd_cup: The QD socket's steel cup: a circle about the socket's hole (centre 550, 563). On the black photo the cup is black on black: its rim is placed by Wing's FDE stock, where the dark ring is 72 px across and the hole in it 42 (1.71), against this photo's 96 px hole: 82 px in radius.; lever: The lever under the cheek, its own piece: its rear ramp, its top edge under the cheek (level, then rising to the front), carried outside the outline at the front and below.; strut_ribs: Where the strut's underside is ribbed: a strip along its lower edge, from the first tooth under the lever's tab to the last above the toe. Its height is the ribbed run.; qd_panel: The recessed panel round the QD socket (the detail pass of 2026-10-13), picked on a gridded crop with the photo's levels raised four times (.cache/detail/bcm-stock-mod-0/grids/pa-qd.png): each wall shows as a band between two lines (the left one columns 302 to 328, the right one 770 to 790, the top one rows 530 to 545) and the outline is drawn down the middle of each band; the arch over the socket is its outer line, a round 93 px about the socket's middle (550, 563) that flares into the upper edge at columns 428 and 662 (its inner line, at 81 px, is the cup's own rim); the foot is the lit upper edge of the bar over the sling slot (row 684). Picks within about 6 px (0.025 in). Drawn over the photo: .cache/detail/bcm-stock-mod-0/grids/overlay.png. The `wing` outline's own arch, picked earlier, is wider than this one (columns 395 to 700): the wing is flush with the body there and its arch isn't used.; triangle: The pocket in the strut's triangle (2026-10-13), picked the same way (grids/pa-tri.png): down the middle of each wall's band (the rear wall's is 22 px across, the strut's 13, the upper one 8 to 16), its three corners rounded as the photo has them. Between it and the strut's ribbed edge the strut's own face is 40 to 46 px across (0.16 to 0.19 in), narrowing to the toe. Picks within about 6 px.) (tools/trace.py)","via":"harvest","note":"The three openings are cut through. The two recessed panels (round the QD socket, in the strut's triangle) are outlined; the lever's own shape and the markings aren't in the outline; the ribs on the strut and on the pad are cut by their measured pitch."},"rear":{"plane":"zy","origin":"the top edge, centred: as the side profile, offset down to the tube axis","offset":{"y":"tube_axis_below_top"},"points":[[-0.731,-0.731],[-0.731,-1.627],[-0.719,-3.187],[-0.673,-3.643],[-0.575,-4.146],[-0.43,-4.712],[-0.384,-4.799],[-0.3,-4.865],[-0.254,-4.883],[0.064,-4.9],[0.272,-4.877],[0.352,-4.831],[0.402,-4.776],[0.448,-4.649],[0.633,-3.869],[0.691,-3.505],[0.725,-3.042],[0.731,-1.673],[0.725,-0.65],[0.679,-0.459],[0.598,-0.303],[0.416,-0.121],[0.22,-0.029],[0,0],[-0.058,0],[-0.254,-0.04],[-0.439,-0.139],[-0.569,-0.263],[-0.673,-0.442],[-0.719,-0.598]],"scaleRefs":["bcm-stock-mod-0.height"],"inputs":{"bcm-stock-mod-0.height":4.9},"tolerance":0.01,"photo":"references/bcm-stock-mod-0 754ef4883e9b (US 9,109,855 B1 (Bravo Company USA), FIG. 3B rear view, sheet 3 of 7)","method":"luminance < 128, inside [915, 714, 1805, 1064], 2 boxes excluded, closing ×3, largest piece, holes filled, opening after the fill 9 px ×1, inset 2 px (half the outline's stroke); rotated -90.0° as declared; scale from bcm-stock-mod-0.height = 4.9 in (y-extent 848 px → 173.1 px/in); origin at x center, y max of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 30 points (IoU 0.996 with the full outline) (tools/trace.py)","via":"harvest","note":"The sheet has the figure turned a quarter. The rear body's two side wings (the ears either side, 0.66 to 1.59 in below the top) are left out of the outline: they are drawn from the side photo at the published width. A utility patent's figure: its height to its width over the ears is 2.93, as the published 4.9 / 1.67."}},"gaps":[{"what":"Its seat on the tube to better than 0.07 in (BCM's photo of it on a rifle is 33.7 px/in; the patent's section with a generic tube reads up to 0.26 in more)","need":"a close, straight side photo of it collapsed on a lower with both receiver pins in view"},{"what":"Its length from its maker (a seller says 6.75 in; BCM's patent section and its photo of the stock on a rifle read 6.66 and 6.64)","need":"BCM's own figure, or a square side photo with a scale in the stock's plane"},{"what":"A weight someone weighed (sellers say 8.2, 8.208 and 8.4 oz; the 2014 reviews 7.5; BCM none)","need":"a review that names its scale, or BCM's own figure"},{"what":"The strut's own width (its ribbed underside is a narrow strip; it is drawn as wide as the butt, 1.46 in), the cheek's own section (drawn as the rear view's narrowed to the cheek's width read on its front face; its facets, the line along its side and the chamfer at its front aren't drawn), and whether body_width is the pad's: the patent's rear view is the pad's outline wherever the pad is the widest thing, and the Wolf Gray stock photographed from behind (9368820c28c7) has the pad's rim a little proud of the body all round and the rear body's face running on down from the wing to the QD panel as one surface, where the model's wing ends in a crease 1.65 in below the top. The cheek's width rests on one photo from ahead (65b0b1c49267, ± 0.03 in): a second one (a0647d7e661f, from ahead of its left side) doesn't show the face's near edge against the cheek's side, and gives no second reading","need":"a camera fitted to BCM's photo from the front right and below (b10b8afd338e: the bore's mouth is a circle of known size) for the strut and a second reading of the cheek, or a front, rear or underside photo square-on with a known size in frame"},{"what":"How deep the two recessed panels are (assumed: 0.05 in round the QD socket, 0.1 in in the triangle, which the obliques show deeper), how their walls lean, and how high the pad's ribs stand at the middle of its face","need":"a camera fitted to BCM's photo of the butt from behind and below (525e4e3ca3a2), or a view square across the stock from below or behind with a known size in frame"},{"what":"Which butt pad a Foliage Green stock sold today has (the one photograph on file, the distributor's earlier one, has the body's green; the Flat Dark Earth and the Wolf Gray stock were photographed later with a dark grey pad)","need":"a later photo of a Foliage Green Mod 0 stock"}]},"bcm-vertical-grip-mod-3-mlok":{"id":"bcm-vertical-grip-mod-3-mlok","name":"Vertical Grip Mod 3 (M-LOK® Compatible*)","manufacturer":"BCM","sku":"BCM-VG-MCMR-MOD-3-BLK","url":"https://bravocompanyusa.com/bcm-vertical-grip-mod-3-m-lok-compatible-black/","category":"vertical_grip","description":"BCM's Vertical Grip Mod 3, the direct-attach M-LOK version: a low-profile polymer vertical grip, 2.2 in long and 2.8 in tall, its body raked 5 degrees to the mounting face, flat textured sides and ridged ends, 1.9 oz. Mounts either way round. Black and Flat Dark Earth.","weight":"bcm-vertical-grip-mod-3-mlok.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"lug":{"origin":["{.lug_x} + {.lug_spacing} / 2",0,0],"note":"The middle of its two T-nuts on the mounting face, what an M-LOK position places (a slot's centre: the two nuts the interval apart go one in each half of it). The nuts are centred on the plate in both side views."}},"interfaces":{"mlok":{"type":"mlok","role":"accessory","anchor":"lug","params":{"lugs":"={.lugs}","reach_inside":"={.reach_inside}"},"flips":true,"note":"Two T-nuts the M-LOK interval apart (lug_spacing, read on two side views scaled by BCM's photo of it on its MCMR). How far the nuts reach inside isn't published, so that check reads as unmade."}},"materials":{"body":{"label":"Grip","finish":"polymer","recolorable":true,"color":"placeholder-polymer-black","sheen":"matte","options":{"black":{"label":"Black","finish":"polymer","color":"placeholder-polymer-black","sheen":"matte","sku":"BCM-VG-MCMR-MOD-3-BLK","source":"https://bravocompanyusa.com/bcm-vertical-grip-mod-3-m-lok-compatible-black/"},"fde":{"label":"Flat Dark Earth","finish":"polymer","color":"bcm-fde","sheen":"matte","sku":"BCM-VG-MCMR-MOD-3-FDE","source":"https://bravocompanyusa.com/bcm-vertical-grip-mod-3-m-lok-compatible-flat-dark-earth/"}},"default":"black","note":"BCM: \"manufactured from high quality, impact resistant polymers\". Black (BCM-VG-MCMR-MOD-3-BLK) and Flat Dark Earth (BCM-VG-MCMR-MOD-3-FDE), each confirmed on its own BCM product page (FDE checked 2026-10-28). One moulding and one colour all over in each: BCM's photos of the black grip (-2 to -6) and of the FDE one (FDE-2) have the mounting face's rim and cells, the flare, the ridged ends, the textured panels and the base the grip's colour; the two T-nuts and screws are black steel in both, and sit inside the handguard, so they aren't drawn. The FDE is the polymer FDE fitted on BCM's Mod 3 pistol grip (data/colors/bcm.yaml bcm-fde); black is the catalog's stand-in polymer black (a black isn't fitted to a photo)."}},"components":{},"geometry":{"model":"bcm-vertical-grip-mod-3-mlok.glb","components":{},"approximations":["Its side is Primary Arms' straight side view of the marked side (_00), leveled on its mounting face and scaled by the length on file; the body's rake and the base's angle are in that outline, and agree with the plain side's photo (_01) to 0.1 and 0.2 degrees.","Across, it is a rounded rectangle at every height: the plate at its width on file (1.02 in, read through the foreshortening of BCM's view from above, the least certain size on file) with its corners rounded as plate_corner_r (assumed), narrowing through the flare to the body's width (0.92 in, from the plate's width and a ratio on BCM's FDE photo) with its upright corners at corner_r. The flare across follows the flare along: at each height the plate's overhang across is the body's overhang along scaled to the plate's.","The ridges are where the side views have them: 35 across the front end and 32 across the rear, at their pitch, from their first ridge's place; the grooves between them run across the end and round its corners, at the depth the silhouette shows and half the pitch wide (assumed). They are cut square to the body's rake.","The mounting face is a rim round open cells, as BCM's views from above show it: a rib along the middle, a rib across at each T-nut with its round boss, and a rib from each boss to each of the rim's ends' corners. The ribs' width, the cells' depth and the rim's wall are assumed (no view sees a cell's floor).","Hollow from the base: an opening with the wall's rim round it (BCM's view from below, -5), drawn up to the depth on file (assumed) under the cells' floors.","Each flat side has its textured panel as a shallow recess (its depth assumed) where the side view has the panel's border; the texture itself, BCM's star and name, and the M-LOK mark on one side aren't drawn. The T-nuts and screws aren't drawn: they sit inside the handguard."],"ledger":["bcm-vertical-grip-mod-3-mlok.length","bcm-vertical-grip-mod-3-mlok.height","bcm-vertical-grip-mod-3-mlok.width","bcm-vertical-grip-mod-3-mlok.body_width","bcm-vertical-grip-mod-3-mlok.lug_x","bcm-vertical-grip-mod-3-mlok.lug_spacing","bcm-vertical-grip-mod-3-mlok.rake","bcm-vertical-grip-mod-3-mlok.base_angle","bcm-vertical-grip-mod-3-mlok.ridges_front","bcm-vertical-grip-mod-3-mlok.ridges_rear","bcm-vertical-grip-mod-3-mlok.ridge_pitch"]},"profiles":{"side":{"plane":"xy","origin":"the plate's rear end on the mounting face (its top surface, which bears on the handguard)","offset":{},"points":[[0,0.112],[0.004,0.049],[0.023,0.024],[0.058,0.002],[0.149,0.013],[0.154,0.009],[0.415,0.012],[0.42,0.008],[0.473,0.011],[0.478,0.007],[0.782,0.013],[0.787,0.009],[0.859,0.014],[0.864,0.009],[0.951,0.015],[0.956,0.011],[1.154,0.014],[1.159,0.01],[1.236,0.015],[1.256,0.007],[1.482,0.013],[1.487,0.008],[1.709,0.014],[1.714,0.009],[1.719,0.014],[1.752,0.017],[1.757,0.012],[1.859,0.014],[1.864,0.01],[1.984,0.013],[2.072,0],[2.125,0.008],[2.143,0.019],[2.159,0.037],[2.166,0.076],[2.155,0.167],[2.126,0.233],[2.095,0.274],[2.013,0.341],[1.986,0.373],[1.959,0.424],[1.941,0.476],[1.963,0.497],[1.962,0.512],[1.922,0.533],[1.944,0.564],[1.943,0.578],[1.903,0.604],[1.925,0.63],[1.924,0.649],[1.889,0.671],[1.915,0.706],[1.907,0.723],[1.879,0.738],[1.89,0.755],[1.907,0.764],[1.905,0.783],[1.885,0.801],[1.902,0.826],[1.901,0.841],[1.876,0.863],[1.898,0.884],[1.897,0.903],[1.867,0.92],[1.894,0.946],[1.893,0.961],[1.868,0.978],[1.89,1.004],[1.884,1.023],[1.859,1.041],[1.881,1.061],[1.88,1.086],[1.859,1.099],[1.877,1.119],[1.876,1.143],[1.855,1.161],[1.873,1.182],[1.872,1.201],[1.846,1.218],[1.869,1.244],[1.868,1.259],[1.847,1.276],[1.865,1.302],[1.864,1.316],[1.838,1.339],[1.861,1.364],[1.86,1.374],[1.839,1.401],[1.852,1.417],[1.856,1.436],[1.83,1.459],[1.848,1.475],[1.847,1.499],[1.826,1.517],[1.844,1.537],[1.842,1.561],[1.827,1.579],[1.84,1.595],[1.838,1.619],[1.818,1.637],[1.836,1.657],[1.834,1.676],[1.814,1.694],[1.832,1.715],[1.831,1.734],[1.81,1.752],[1.828,1.777],[1.827,1.792],[1.806,1.815],[1.819,1.83],[1.823,1.845],[1.801,1.877],[1.819,1.902],[1.813,1.921],[1.798,1.935],[1.811,1.95],[1.809,1.979],[1.789,1.992],[1.807,2.013],[1.805,2.037],[1.789,2.055],[1.803,2.07],[1.801,2.094],[1.786,2.108],[1.799,2.128],[1.797,2.152],[1.777,2.17],[1.795,2.186],[1.793,2.215],[1.777,2.233],[1.791,2.248],[1.789,2.272],[1.773,2.29],[1.787,2.306],[1.785,2.33],[1.769,2.348],[1.782,2.368],[1.781,2.388],[1.765,2.406],[1.778,2.431],[1.777,2.45],[1.761,2.468],[1.774,2.489],[1.773,2.508],[1.752,2.526],[1.77,2.546],[1.769,2.565],[1.733,2.592],[1.726,2.693],[1.697,2.732],[1.683,2.731],[1.653,2.748],[1.599,2.759],[1.502,2.762],[1.497,2.767],[1.449,2.763],[1.444,2.768],[1.126,2.751],[1.097,2.744],[1.083,2.748],[1.078,2.743],[1.059,2.746],[1.03,2.739],[0.809,2.724],[0.799,2.733],[0.784,2.732],[0.775,2.722],[0.434,2.694],[0.43,2.689],[0.272,2.668],[0.172,2.642],[0.112,2.609],[0.088,2.576],[0.08,2.547],[0.092,2.441],[0.065,2.41],[0.066,2.391],[0.087,2.373],[0.074,2.353],[0.075,2.329],[0.096,2.311],[0.078,2.29],[0.079,2.281],[0.085,2.267],[0.105,2.254],[0.087,2.233],[0.088,2.214],[0.109,2.196],[0.096,2.176],[0.097,2.157],[0.118,2.134],[0.104,2.118],[0.106,2.094],[0.127,2.076],[0.113,2.061],[0.115,2.032],[0.136,2.014],[0.118,1.994],[0.119,1.979],[0.144,1.957],[0.126,1.936],[0.128,1.917],[0.148,1.899],[0.135,1.879],[0.137,1.855],[0.157,1.837],[0.144,1.822],[0.146,1.798],[0.166,1.78],[0.153,1.764],[0.149,1.745],[0.175,1.718],[0.157,1.702],[0.158,1.683],[0.184,1.66],[0.166,1.64],[0.167,1.62],[0.188,1.603],[0.17,1.577],[0.171,1.568],[0.197,1.54],[0.179,1.52],[0.18,1.505],[0.206,1.483],[0.188,1.462],[0.189,1.443],[0.21,1.425],[0.197,1.405],[0.198,1.381],[0.224,1.364],[0.201,1.338],[0.207,1.319],[0.227,1.306],[0.21,1.28],[0.211,1.266],[0.219,1.255],[0.229,1.255],[0.241,1.244],[0.219,1.223],[0.22,1.204],[0.245,1.186],[0.223,1.156],[0.229,1.142],[0.254,1.124],[0.236,1.108],[0.233,1.089],[0.241,1.077],[0.25,1.078],[0.263,1.067],[0.241,1.041],[0.242,1.027],[0.272,1.005],[0.249,0.984],[0.251,0.965],[0.281,0.947],[0.258,0.926],[0.26,0.902],[0.282,0.897],[0.295,0.885],[0.263,0.85],[0.264,0.835],[0.287,0.825],[0.3,0.813],[0.3,0.804],[0.264,0.777],[0.27,0.753],[0.29,0.745],[0.296,0.731],[0.28,0.713],[0.259,0.704],[0.261,0.68],[0.286,0.663],[0.271,0.64],[0.256,0.639],[0.241,0.616],[0.267,0.589],[0.251,0.566],[0.228,0.56],[0.221,0.552],[0.222,0.533],[0.243,0.515],[0.218,0.455],[0.161,0.369],[0.123,0.33],[0.09,0.309],[0.039,0.25],[0.014,0.195]],"scaleRefs":["bcm-vertical-grip-mod-3-mlok.length"],"inputs":{"bcm-vertical-grip-mod-3-mlok.length":2.166},"tolerance":0.004,"photo":"references/bcm-vertical-grip-mod-3-mlok 9b7012677b76 (Primary Arms BCM-VG-MCMR-MOD-3-BLK_00.jpg: the grip alone on white, upright, its marked side, a straight side view along the handguard, 1152 x 768)","method":"luminance < 200, inside [320, 90, 810, 720], 2 polygons excluded, closing ×2, largest piece, holes filled; rotated +183.9° as declared; scale from bcm-vertical-grip-mod-3-mlok.length = 2.166 in (x-extent 450 px → 207.5 px/in); origin at x min, y min of the outline; Douglas-Peucker at 0.004 in with the extremes kept: 287 points (IoU 0.997 with the full outline) (tools/trace.py)","via":"harvest","note":"Primary Arms' straight side view of the marked side, leveled on the mounting face and scaled by the length on file. The ridges are the notches down both ends; the T-nuts above the face are cut away."}},"gaps":[{"what":"Any size from BCM or a seller (length, height, width)","need":"A seller's table or a review's calipers; every size here is read on photos, the width through an oblique one"},{"what":"A straight view of the grip's end or base, for its width and section","need":"A square end view (the ridged face) or a view straight up at the base; a seller's gallery may have one"},{"what":"How far the T-nuts reach inside the handguard (reach_inside)","need":"A drawing of the M-LOK T-nut BCM uses, or a straight photo of a nut beside its 7 mm flats"},{"what":"Which way round BCM means by \"forward angle\"","need":"BCM's words or a straight side photo of it mounted, the muzzle in frame; the model is drawn as BCM's own installed photo (-6) has it, read by the side its marks are on"}]},"blackdog-22lr-15":{"id":"blackdog-22lr-15","name":"Sonic X 15-round .22 LR magazine","manufacturer":"Black Dog Machine","category":"magazine","description":"The Sonic X is Black Dog's sonic-welded X-Form (Bear Creek's listing names it so). The 10-round is the same body (Black Dog: 5 in and 3.2 oz for both), so its photos measure this part. The user is buying the 15-round (2026-09-30).","weight":"blackdog-22lr-15.weight","cartridge":{"takes":[".22 LR"],"stated":"AR15.22 \"Sonic Weld\" Magazine … Known-Compatible Models .22 Conversion Bolt Kits: BoreBuddy .22LR Ciener/Atchisson .22LR CMMG (Old Bolt Kit) .22LR","source":"https://www.blackdogmachinellc.net/sonic-x.aspx (Black Dog Machine's page for the magazine, as cached: harvest.quote)"},"rounds":{"capacity":"blackdog-22lr-15.capacity","each":"std.cartridge_22lr.weight"},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"magwell":{"origin":[0,"-{.catch_notch_top}",0],"note":"The upper edge of its catch notch, at its spine rib's rear face: what hangs on the lower's catch (since 2026-10-05 every magazine is seated by its own notch; this one sits where it did). Magazine frame: origin at the rear face of the body (its spine) at the top of the feed lips."}},"interfaces":{"magwell":{"type":"ar15.magwell","role":"magazine","anchor":"magwell","params":{"family":"5.56"},"flips":false,"note":"A .22 LR magazine in an AR-15 (5.56) magazine envelope."}},"materials":{"body":{"label":"Magazine body","finish":"translucent_polymer","recolorable":false,"color":"blackdog-smoke","options":{"smoke":{"label":"Smoke","finish":"translucent_polymer","color":"blackdog-smoke","source":"https://www.blackdogmachinellc.net/sonic-x.aspx"},"black":{"label":"Black","finish":"polymer","color":"placeholder-polymer-black","source":"https://www.blackdogmachinellc.net/sonic-x.aspx"}},"default":"smoke","note":"Black Dog sells each capacity in black and smoke, and in nothing else (its page's options: \"15 Round- Smoke- Nylon Lip\", \"15 Round- Black- Nylon Lip\"; \"Color: Smoke or Black\"); it states no number for either. The build uses smoke (the user's choice 2026-09-30; Nordic's photo of the included magazine shows smoke). The black body is a smooth, glossy moulded black (ar15discounts' side view 460457598fff; Black Dog's own SMOKEANDBLACKCOLORS.jpg reads it #505458 under its lights): a black on a glossy face isn't fitted to a photo, and it keeps the catalog's polymer black. In the black one everything inside is hidden and the webs are the body's black (they follow it)."},"lips":{"label":"Feed-lip block","finish":"polymer","recolorable":false,"color":"placeholder-polymer-black","note":"Glass-filled nylon (Black Dog: \"Glass Filled Nylon Feed Lip\", https://www.blackdogmachinellc.net/sonic-x.aspx), a matte charcoal black on the smoke and the black bodies alike (ar15discounts' two side views, 0eb77371d877 and 460457598fff; the user's own from above, c532659922ef). A black: not fitted to a photo. The follower under it is the same black (the user's photo from above); it and the spring, bare steel wire seen through a smoke wall, aren't drawn."},"webs":{"label":"Internal webs","finish":"polymer","recolorable":false,"color":"blackdog-smoke-edge","follows":{"slot":"body","options":{"black":{"finish":"polymer","color":"placeholder-polymer-black"}}},"note":"The body's internal webs, dark where they're seen edge-on through a smoke wall (Black Dog's side view); hidden inside a black body."}},"components":{"body":{"label":"Body","material":"body"},"lips":{"label":"Feed-lip block","material":"lips"}},"geometry":{"model":"blackdog-22lr-15.glb","components":{},"approximations":["From the user's own 10-round (Black Dog gives the 15 its body), photographed on its sides, edges, top and base beside a tape (2026-10-03): its side outline at the body's 0.868 in, the spine rib at its own 0.441 down the middle of the rear, the feed-lip block narrowing from 0.60 where it leaves the body through its shoulder and neck to the lips (0.14), and the block as it shows through the smoke body, down inside it. Until then it was a retailer's photo of the same body, 1.7% small, at one thickness, the block as wide as the body.","The body is drawn solid, a tinted volume, with what is dark through a smoke wall inside it: the feed-lip block, the internal webs, the six weld bosses and the round post at mid-body as posts across it, and the cartridge channel's rear wall, middle line and front wall where the side photo has them, curving forward as they go down. Those three are drawn as a low rib inside each side wall (as far in as the wall is thick): a wall drawn across the body would be dark from the front, where the real one is as clear as the side it is seen through. The follower and the spring aren't drawn. The two feed lips are one piece.","On the outside (2026-10-05, from the user's close, top and base photos): the three grooves down each side wall, each as wide as the side photo has it and as deep as the notch it cuts in the base's outline, the front one beginning under the top with a round end; a countersunk dot over each boss (as deep as half its width: its depth isn't read); on the left, the recess open to the top face, the catch notch through the wall under it with a dark floor behind, and the lip that stands out under the notch (all inside the magwell when seated); in the base, its slot with the round end, as deep as the wall, dark behind. The catch notch's corners are rounded by eye.","Not drawn: the moulded markings (Black Dog Machine LLC, X-FORM, 10 RND), the weld seam round the body, the top face's well round the block, the pads inside the front wall. Edges broken at 0.06 in (the body's read 0.07 to 0.10) and 0.02 (the block's)."],"ledger":["blackdog-22lr-15.front_to_back","blackdog-22lr-15.overall_height","blackdog-22lr-15.feed_lip_block_height","blackdog-22lr-15.width","blackdog-22lr-15.spine_rib_width","blackdog-22lr-15.spine_rib_depth","blackdog-22lr-15.feed_lip_block_base_width","blackdog-22lr-15.feed_lips_width","blackdog-22lr-15.catch_notch_top","blackdog-22lr-15.wall_thickness","blackdog-22lr-15.boss_diameter","blackdog-22lr-15.groove_front_depth","blackdog-22lr-15.groove_middle_depth","blackdog-22lr-15.groove_rear_depth","blackdog-22lr-15.catch_recess_depth","blackdog-22lr-15.catch_lip_proud","blackdog-22lr-15.base_slot_width","blackdog-22lr-15.base_slot_length"]},"profiles":{"side":{"plane":"xy","origin":"the rear face of the body (its spine) at the top of the feed lips: the magazine frame origin, where the lower's magazine seat puts it","offset":{},"points":[[0,-4.789],[0.006,-5.74],[0.044,-5.79],[0.119,-5.796],[0.932,-5.655],[1.119,-5.593],[1.281,-5.589],[2.473,-5.377],[2.523,-5.276],[2.524,-4.713],[2.515,-0.92],[2.449,-0.865],[1.701,-0.85],[1.669,-0.394],[1.606,-0.33],[1.655,-0.052],[1.595,-0.014],[1.409,0],[0.649,-0.101],[0.621,-0.237],[0.521,-0.317],[0.423,-0.827],[0.211,-0.862],[0.173,-0.893],[0.158,-1.172],[0.006,-1.245]],"features":{"webs":[[[1.462,-1.999],[2.459,-2.01],[2.457,-2.178],[1.46,-2.167]],[[1.45,-3.037],[2.447,-3.048],[2.445,-3.21],[1.448,-3.199]],[[1.438,-4.08],[2.435,-4.092],[2.433,-4.266],[1.436,-4.254]],[[1.426,-5.113],[2.423,-5.124],[2.422,-5.275],[1.424,-5.263]],[[0.076,-1.994],[0.458,-1.999],[0.457,-2.155],[0.074,-2.151]],[[0.064,-3.044],[0.446,-3.048],[0.444,-3.222],[0.062,-3.218]],[[0.052,-4.076],[0.434,-4.08],[0.433,-4.237],[0.05,-4.233]],[[0.04,-5.126],[0.422,-5.13],[0.421,-5.275],[0.038,-5.271]]],"bosses":[[[0.204,-0.917],[0.343,-0.919],[0.342,-1.058],[0.203,-1.056]],[[2.257,-0.964],[2.396,-0.965],[2.394,-1.105],[2.255,-1.103]],[[0.203,-3.057],[0.342,-3.059],[0.34,-3.198],[0.201,-3.196]],[[2.256,-3.069],[2.395,-3.071],[2.393,-3.21],[2.254,-3.208]],[[0.212,-5.238],[0.351,-5.239],[0.35,-5.379],[0.211,-5.377]],[[2.226,-5.122],[2.365,-5.123],[2.364,-5.263],[2.225,-5.261]]],"post":[[[0.829,-4.068],[1.015,-4.07],[1.012,-4.255],[0.827,-4.253]]],"groove_rear":[[[0.388,-0.844],[0.515,-0.845],[0.458,-5.797],[0.331,-5.796]]],"groove_middle":[[[1.052,-0.851],[1.202,-0.853],[1.145,-5.805],[0.995,-5.804]]],"groove_front":[[[1.783,-1.074],[2.067,-1.078],[2.012,-5.815],[1.728,-5.812]]],"rails":[[[0.524,-1.577],[0.546,-2.204],[0.577,-3.074],[0.603,-3.829],[0.682,-4.313],[0.772,-4.802],[0.893,-5.366],[0.932,-5.357],[0.811,-4.794],[0.721,-4.306],[0.643,-3.826],[0.617,-3.072],[0.587,-2.202],[0.565,-1.575]],[[1.174,-1.584],[1.184,-2.211],[1.214,-3.081],[1.252,-3.838],[1.375,-4.322],[1.468,-4.81],[1.572,-5.293],[1.612,-5.284],[1.507,-4.802],[1.414,-4.313],[1.293,-3.832],[1.255,-3.08],[1.224,-2.21],[1.214,-1.583]],[[1.455,-1.314],[1.439,-2.213],[1.47,-3.084],[1.519,-3.829],[1.63,-4.324],[1.706,-4.731],[1.746,-4.724],[1.669,-4.317],[1.56,-3.824],[1.51,-3.083],[1.48,-2.213],[1.496,-1.315]]]},"scaleRefs":["blackdog-22lr-15.front_to_back","blackdog-22lr-15.overall_height"],"angleRef":"std.ar15.magwell_wall_lean","inputs":{"blackdog-22lr-15.front_to_back":2.514,"blackdog-22lr-15.overall_height":5.79,"std.ar15.magwell_wall_lean":0},"tolerance":0.02,"photo":"references/blackdog-22lr-15 ffcd6aa3a249 (the user's own 10-round (the 15's body) lying on its left side on tile, straight down from about 4 ft, a tape beside it)","method":"luminance < 70, inside [800, 700, 1340, 1820], 1 polygons excluded, closing ×3, largest piece, holes filled, notches filled in [840, 1640, 1300, 1800] (disk closing, r 14 px), notches filled in [980, 1690, 1090, 1770] (disk closing, r 80 px); rotated -0.7° (counter-clockwise) so the edges' mean lean in the band 0.3–0.9 of the height (-0.6° rear, -0.7° front in the photo) becomes std.ar15.magwell_wall_lean = 0°; re-measured 0.0°/-0.0°; scale from blackdog-22lr-15.front_to_back = 2.514 in (median width over 0.3–0.7 of the height from the top, 432–434 px 433 px → 172.2 px/in) and blackdog-22lr-15.overall_height = 5.79 in (y-extent 1000 px → 172.6 px/in), which agree within 0.2%; mean 172.4 px/in; origin at x min, y max of the outline; Douglas-Peucker at 0.02 in with the extremes kept: 26 points (IoU 0.995 with the full outline); checks: −y_max in x [1.9, 2.3] 0.862 ± 0.010 in vs blackdog-22lr-15.feed_lip_block_height 0.867 ± 0.015 (conflict): agrees; features through the same placement (webs: four across the front section, from the cartridge channel's wall to the front wall, and four across the rear strip; rows where each section's column is darker than its surround, ends inside the walls; bosses: the six weld bosses, each a dark disc with a small hole at its middle: three down the rear strip, three inside the front wall; a box round each disc as this photo has it (the model takes each box's middle, and the disc's size from the close photo: boss_diameter); post: a round dark spot at mid-body, seen from both sides (a post across the body), 33 px across; groove_rear: the narrow groove a third of an inch ahead of the rear face, from the body's top to its base: between its two dark edges; groove_middle: the narrow groove at mid-body, from the body's top to its base: between its two dark edges; groove_front: the wide round-bottomed groove ahead of the cartridge channel, from its rounded upper end (the top of the arc) to the base: between the middles of its two dark borders; rails: the cartridge channel's rear wall, the line down its middle and its front wall, where they show through the side wall: a 7 px band along each one's dark core, picked at six or seven stations) (tools/trace.py)","via":"user","note":"The markings aren't drawn; the translucent body is drawn solid, with its internal webs, bosses and rails (features) inside and its grooves cut in its sides."}},"gaps":[]},"blackdog-22lr-25":{"id":"blackdog-22lr-25","name":"Sonic X 25-round .22 LR magazine","manufacturer":"Black Dog Machine","category":"magazine","description":"Curved 25-round Sonic X (sonic-welded X-Form) body with the same feed-lip block and magwell section as the 15-round, so it seats the same way. Onboarded through the pipeline (M1c); traced in M3; modelled 2026-10-05 from Black Dog's photo of the pair, with the 15's figures (the user's own magazine) for what no photo of a 25 gives.","weight":"blackdog-22lr-25.weight","cartridge":{"takes":[".22 LR"],"stated":"AR15.22 \"Sonic Weld\" Magazine … Known-Compatible Models .22 Conversion Bolt Kits: BoreBuddy .22LR Ciener/Atchisson .22LR CMMG (Old Bolt Kit) .22LR","source":"https://www.blackdogmachinellc.net/sonic-x.aspx (Black Dog Machine's page for the magazine, as cached: harvest.quote)"},"rounds":{"capacity":"blackdog-22lr-25.capacity","each":"std.cartridge_22lr.weight"},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"magwell":{"origin":[0,"-{.catch_notch_top}",0],"note":"The upper edge of its catch notch, at its spine's rear face: what hangs on the lower's catch. The 25-round has the 15's top section (Black Dog's capacities share it), so its notch is taken as the 15's (its ledger says so). Magazine frame: origin at the rear face of the body's straight top (its spine) at the top of the feed lips."}},"interfaces":{"magwell":{"type":"ar15.magwell","role":"magazine","anchor":"magwell","params":{"family":"5.56"},"flips":false}},"materials":{"body":{"label":"Magazine body","finish":"translucent_polymer","recolorable":false,"color":"blackdog-smoke","options":{"smoke":{"label":"Smoke","finish":"translucent_polymer","color":"blackdog-smoke","source":"https://www.blackdogmachinellc.net/sonic-x.aspx"},"black":{"label":"Black","finish":"polymer","color":"placeholder-polymer-black","source":"https://www.blackdogmachinellc.net/sonic-x.aspx"}},"default":"smoke","note":"Black Dog sells each capacity in black and smoke, and in nothing else (its page's options: \"25 Round- Smoke- Nylon Lip\", \"25 Round- Black- Nylon Lip\"; \"Color: Smoke or Black\"); it states no number for either (Bear Creek sells the black one as SW-25BL-NY). The black body is a smooth, glossy moulded black (Black Dog's own 25smokeblackboth.JPG, c8bd551fb5e2): not fitted to a photo. In the black one the weld bosses are the body's black (they follow it)."},"lips":{"label":"Feed-lip block","finish":"polymer","recolorable":false,"color":"placeholder-polymer-black","note":"Glass-filled nylon (Black Dog: \"Glass Filled Nylon Feed Lip\", https://www.blackdogmachinellc.net/sonic-x.aspx), a matte charcoal black on the smoke and the black bodies alike (ar15discounts' two side views, 0eb77371d877 and 460457598fff; the user's own from above, c532659922ef). A black: not fitted to a photo. The follower under it is the same black (the user's photo from above); it and the spring, bare steel wire seen through a smoke wall, aren't drawn."},"webs":{"label":"Weld bosses","finish":"polymer","recolorable":false,"color":"blackdog-smoke-edge","follows":{"slot":"body","options":{"black":{"finish":"polymer","color":"placeholder-polymer-black"}}},"note":"What is dark through a smoke wall: the six weld bosses across the body and the floor behind the catch notch; hidden inside a black body."}},"components":{"body":{"label":"Body","material":"body"},"lips":{"label":"Feed-lip block","material":"lips"}},"geometry":{"model":"blackdog-22lr-25.glb","components":{},"approximations":["Its side outline from Black Dog's photo of the black 25 beside the smoke one, turned until its straight top stands square and scaled by that top's front-to-back, at the body's 0.868 in. It is the 15's design in a longer, curved body (Black Dog's line-up has the two side by side with one top section), and what no photo of a 25 on file gives is the 15's figure, read on the user's own magazine and not on a 25: the spine rib down the middle of the rear, the feed-lip block narrowing to the lips, the wall's thickness, and everything on the left side.","On the outside (2026-10-05): the three grooves down each side wall, following the curve. The front one is where the photo has its two walls, beginning under the top with a round end. The rear and the middle are where the 15's are across the body's width, which in every row of the photo is on the dark line of the groove's wall: their widths are the 15's share of this body's width, not read on the 25. Each is as deep as the 15's. A countersunk dot at each of the six weld dots, where the photo has them. The photo is of the right side: the left is drawn the same, with the 15's recess, catch notch and lip where the 15 has them (inside the magwell when seated).","The body is drawn solid, a tinted volume, with the feed-lip block and the six weld bosses dark inside it. Not drawn: the internal webs and the cartridge channel's walls that show through a smoke wall (they are in the photo, on the smoke magazine of the pair, and aren't traced yet), the follower and the spring, the slot in the base (no photo of a 25's base is on file), the moulded markings, the weld seam round the body. Edges broken at 0.06 in and 0.02 (the block's), as the 15's."],"ledger":["blackdog-22lr-25.front_to_back","blackdog-22lr-25.overall_height","blackdog-22lr-25.width","blackdog-22lr-25.feed_lip_block_base_width","blackdog-22lr-25.feed_lip_block_height","blackdog-22lr-25.catch_notch_top"]},"profiles":{"side":{"plane":"xy","origin":"the rear face of the body's straight top (its spine) at the top of the feed lips: the magazine frame origin, where the lower's magazine seat puts it (the same top section as the 15-round's)","offset":{},"points":[[-0.003,-1.276],[0.022,-3.383],[0.135,-4.624],[0.387,-5.795],[0.991,-7.739],[1.049,-7.815],[1.046,-7.913],[1.093,-7.964],[1.225,-7.972],[3.259,-7.384],[3.339,-7.32],[3.355,-7.23],[2.748,-5.156],[2.561,-4.158],[2.509,-3.417],[2.524,-0.944],[2.464,-0.884],[1.822,-0.885],[1.724,-0.854],[1.695,-0.468],[1.629,-0.35],[1.675,-0.069],[1.493,0],[0.659,-0.08],[0.626,-0.222],[0.518,-0.286],[0.409,-0.807],[0.388,-0.838],[0.153,-0.861],[0.123,-0.904],[0.128,-1.165],[0.023,-1.212]],"features":{"groove_rear":[[[0.364,-1.36],[0.365,-1.447],[0.366,-1.664],[0.372,-2.098],[0.374,-2.533],[0.377,-2.968],[0.384,-3.402],[0.406,-3.833],[0.448,-4.26],[0.505,-4.685],[0.583,-5.105],[0.68,-5.523],[0.796,-5.936],[0.923,-6.348],[1.053,-6.758],[1.18,-7.17],[1.259,-7.427],[1.319,-7.634],[1.438,-7.611],[1.38,-7.404],[1.301,-7.147],[1.175,-6.736],[1.045,-6.325],[0.918,-5.913],[0.802,-5.5],[0.705,-5.083],[0.628,-4.662],[0.571,-4.237],[0.53,-3.81],[0.51,-3.378],[0.503,-2.944],[0.501,-2.509],[0.499,-2.074],[0.494,-1.64],[0.492,-1.423],[0.491,-1.336]]],"groove_middle":[[[1.029,-1.235],[1.03,-1.322],[1.032,-1.539],[1.035,-1.974],[1.035,-2.409],[1.036,-2.844],[1.039,-3.279],[1.054,-3.711],[1.091,-4.14],[1.146,-4.565],[1.22,-4.986],[1.317,-5.403],[1.433,-5.817],[1.561,-6.228],[1.689,-6.639],[1.814,-7.051],[1.892,-7.308],[1.943,-7.516],[2.085,-7.49],[2.035,-7.282],[1.957,-7.024],[1.833,-6.612],[1.704,-6.201],[1.577,-5.79],[1.46,-5.376],[1.364,-4.959],[1.291,-4.538],[1.236,-4.113],[1.2,-3.684],[1.188,-3.251],[1.184,-2.816],[1.184,-2.381],[1.185,-1.946],[1.182,-1.511],[1.182,-1.293],[1.182,-1.206]]],"groove_front":[[[1.765,-1.184],[1.766,-1.402],[1.725,-1.845],[1.669,-2.29],[1.667,-2.726],[1.663,-3.162],[1.698,-3.591],[1.746,-4.017],[1.798,-4.442],[1.868,-4.865],[1.961,-5.282],[2.074,-5.696],[2.193,-6.109],[2.323,-6.52],[2.445,-6.933],[2.521,-7.191],[2.581,-7.397],[2.865,-7.344],[2.804,-7.137],[2.729,-6.879],[2.608,-6.467],[2.477,-6.056],[2.357,-5.643],[2.245,-5.229],[2.151,-4.812],[2.087,-4.388],[2.04,-3.962],[2.003,-3.533],[1.977,-3.103],[1.972,-2.669],[1.966,-2.234],[2.014,-1.79],[2.05,-1.348],[2.05,-1.131]]],"bosses":[[[0.141,-0.912],[0.288,-0.884],[0.315,-1.032],[0.168,-1.059]],[[2.197,-1.027],[2.344,-0.999],[2.372,-1.146],[2.225,-1.174]],[[0.285,-4.465],[0.432,-4.437],[0.459,-4.585],[0.312,-4.612]],[[2.253,-4.226],[2.4,-4.199],[2.428,-4.346],[2.281,-4.374]],[[1.098,-7.523],[1.245,-7.495],[1.272,-7.642],[1.125,-7.67]],[[3.013,-7.174],[3.16,-7.147],[3.187,-7.294],[3.04,-7.322]]]},"scaleRefs":["blackdog-22lr-25.front_to_back"],"angleRef":"std.ar15.magwell_wall_lean","inputs":{"blackdog-22lr-25.front_to_back":2.514,"std.ar15.magwell_wall_lean":0},"tolerance":0.02,"photo":"references/blackdog-22lr-25 c8bd551fb5e2 (Sonic X 25-round, black, beside the smoke one, right side on white (Black Dog))","method":"luminance < 200, inside [30, 50, 330, 800], closing ×2, largest piece, holes filled; rotated +10.6° (counter-clockwise) so the edges' mean lean in the band 0.2–0.4 of the height (10.1° rear, 11.1° front in the photo) becomes std.ar15.magwell_wall_lean = 0°; re-measured -0.6°/0.6°; scale from blackdog-22lr-25.front_to_back = 2.514 in (median width over 0.18–0.3 of the height from the top, 234–236 px 235 px → 93.5 px/in); origin at x min, y max of the outline (x over 0.18–0.3 of the height from the top); Douglas-Peucker at 0.02 in with the extremes kept: 32 points (IoU 0.994 with the full outline); features through the same placement (groove_rear: the narrow groove nearest the spine, as a band down the curve: at each of seventeen rows, where the 15-round's own rear groove is across the body's width between the photo's two edges (the top section is the 15's; in every row the band's rear edge is on the dark line of the groove's wall). Its two edges, the rear one down and the front one back up; groove_middle: the middle groove, the same way: where the 15's is across the width, on the dark line of its wall in every row; groove_front: the wide groove toward the front, which begins under the top with a round end (its top at row 172): its two walls as each row has them (the start of its rear wall's dark, the end of its front wall's). Below the top section it is 5 to 8 px nearer the spine than the 15's place across the width would have it: it curves more tightly than the body's front edge; bosses: the six weld dots, a box round each: two at the top (behind the rear groove and ahead of the front one), two at mid-body, two above the base) (tools/trace.py)","via":"harvest","note":"The black one's outline, with its three grooves and six weld dots as features. Its moulded markings aren't traced."}},"gaps":[{"what":"What shows through a smoke wall: the internal webs and the cartridge channel's walls","need":"Nothing more for their places (c8bd551fb5e2 has the smoke one beside the black): a pass on the model, as the 15's had"},{"what":"Its left side and its base: the catch notch and the base's slot are the 15's, and the base's isn't drawn","need":"A seller's or an owner's photo of a Sonic X 25 from the left and from under its base (the user doesn't own one)"},{"what":"The rear and middle grooves' widths and every groove's depth: the 15's","need":"A close photo of a 25's side wall, or its base's outline seen end on, where each groove shows as a notch"}]},"cloud-defensive-rein":{"id":"cloud-defensive-rein","name":"REIN","manufacturer":"Cloud Defensive","sku":"REIN 3.0-DF-S-650 BLK","url":"https://clouddefensive.com/products/cloud-defensive-rein-black","category":"light","description":"Cloud Defensive's full-size weapon light: 100,000 candela and 1,250 lumens from one 18650 (or two CR123A), with a remote switch and an inline M-LOK mount in the box. Its page is titled 'Cloud Defensive REIN (Black)'; the maker calls this generation the REIN 3.0 ('The gold standard. The REIN 3.0'). Also sold in FDE and Earth Brown.","weight":"cloud-defensive-rein.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"lug":{"origin":["{.lug_x} + {.lug_spacing} / 2",0,0],"note":"The middle of the mount's two T-nut screws on its underside: what an M-LOK position places. Since 2026-10-05 the middle of the two, not the rear one: a slot's position is its centre, and two nuts the M-LOK interval apart go one in each half of it (the rear nut on the centre put the front one 4 mm past the slot's end, over the web). Light frame: origin at the mount's rear end on that face, +x toward the lens, +y out of the face (away from the handguard, toward the light's body)."}},"interfaces":{"mlok":{"type":"mlok","role":"accessory","anchor":"lug","params":{"lugs":"={.lugs}","reach_inside":"={.reach_inside}"},"flips":false,"note":"The one way of mounting its box provides: the inline mount's two T-nuts, an M-LOK interval apart, in one slot at the mount's rear end, the light ahead of them. It doesn't turn end for end (the lens faces the muzzle). How far the nuts reach inside isn't published. The body also takes any Scout-pattern mount (the maker), none of which is in the box."}},"materials":{"body":{"label":"Body","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized_matte","color":"placeholder-black","sku":"REIN 3.0-DF-S-650 BLK","source":"https://clouddefensive.com/products/cloud-defensive-rein-black"},"fde":{"label":"FDE","finish":"anodized_matte","color":"cloud-defensive-fde","sku":"REIN 3.0-DF-S-650 FDE","source":"https://clouddefensive.com/products/cloud-defensive-rein-fde"},"earth_brown":{"label":"Earth Brown","finish":"anodized_matte","color":"cloud-defensive-earth-brown","sku":"REIN 3.0 DF-S-650 EARTH BROWN","source":"https://clouddefensive.com/products/rein-3-0-coyote-brown-copy"},"od_green":{"label":"OD Green","finish":"anodized_matte","color":"cloud-defensive-od-green","sku":"CD2109-DFS-ODG","source":"https://gritroutdoors.com/cloud-defensive-rein-3-0-weapon-light-cd2109-dfs-odg"}},"default":"black","note":"Type III hard-coat anodized 6061-T6 aluminium (the maker): the head, the centre section with its two feet, the collar, the switch housing and the tail cap's ring are the one anodize in each colour. Black, FDE and Earth Brown are the maker's own pages (the Earth Brown page's address still says coyote brown); OD Green is a colour one seller lists under the maker's number (GRITR Outdoors, CD2109-DFS-ODG) and the maker's site doesn't, as read. Each colour is matched to the two pictures on file of that light, the maker's pose from the side and from behind; the two Earth Brown pictures are 20 to 30 levels apart (the side view is the darker), and the colour sits between them. A reviewer's photographs of an Earth Brown light on a rifle (Inside Safariland) are a brighter orange bronze under daylight. Every colour is drawn matte (`anodized_matte`; the black was a receiver's satin `anodized` until 2026-10-06): the maker's pictures of all four have a soft sheen and no bright line along the tube, and a receiver's satin anodize draws a hard one on a round part. Black is the placeholder the optics use, not matched."},"lens":{"label":"Lens","finish":"glass","recolorable":false,"color":"glass-clear","note":"3 mm glass (the maker)."},"button":{"label":"Tail cap button","finish":"rubber","recolorable":false,"color":"placeholder-polymer-black","note":"The rubber button in the tail cap's rear face: a dark grey rubber with the maker's mark on every colour of light (the maker's pictures of the black, FDE and Earth Brown lights from behind, GRITR's of the OD Green one)."},"latch":{"label":"Latches","finish":"polymer","recolorable":false,"color":"placeholder-polymer-black","note":"The ribbed latches round the switch housing: black on every colour of light (the same pictures). What they are made of isn't said on a page on file: drawn as a black plastic."},"mount":{"label":"Mount","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","note":"The inline M-LOK mount (TOR-MLOKINLINE BLK): black in every photo on file, beside the FDE, Earth Brown and OD Green lights too, and its two T-nut screws black in their pockets. The maker's list of mounts has others in black and FDE; this one's page is black only, as read."}},"components":{"body":{"label":"Light","material":"body"},"mlok":{"label":"Inline M-LOK mount","material":"mount"}},"geometry":{"components":{"body":"cloud-defensive-rein.body.glb","mlok":"cloud-defensive-rein.mlok.glb"},"approximations":["The body is its traced silhouette (Rifle Supply's photo of the light standing, scaled column by column by its own tube and to the published length) turned about its axis. That photo sees the light from 12 degrees off square at the lens and 27 at the tail, so each shoulder's rim shows as a short arc and steps are drawn as ramps up to 0.06 in long.","Six flats on the bezel 60 degrees apart, at the size of the one the photo shows best; one flat along the grip section, opposite the feet (where the wordmark is on the lights that carry it); four oval latches a quarter turn apart on the switch housing (three show in any one photo), drawn as plain pads without their ribs, in their own material (black on every colour of light). The tail cap's rubber button is a disc of its own material in a recess of the rear face, at the button's size and with a hairline ring open round it, its face in the plane of the rear face (the real one is flush in its rim). The tail cap's facets, the collar's, the engraving and the cable's exit aren't drawn.","The two mounting feet under the grip bands are drawn from one side photo: their length along the body and how far they stand off are read; their width across the body isn't (no photo shows them from an end), and they are drawn just narrow enough to stay on the mount's bar in either of its two positions (0.34 in). Each is drawn as long as its band where it joins the body, narrowing to its sole.","A hairline groove at each of the two joints that show as lines round the body (the tail cap against the switch housing, the bezel against the head's rear half), as deep as it is wide: their depth isn't measured. The other joints (the collar's two ends, the head against the tube) are steps in the outline.","The lens is a disc of the bezel's clear opening at the bezel's front face: how far the glass sits behind the rim isn't measured.","The inline mount is a flat bar at its photo-read sizes: one thickness, a rounded rear end, bevels along the T-nut end's upper edges, two pocketed screws for the T-nuts and the two open holes of the row the light isn't bolted to. The pockets' depth isn't measured (drawn to half the bar's thickness); the T-nuts under it and the screws' heads in its underside aren't drawn.","The light is on the mount's rear row of holes (its axis 0.13 in to the left of the mount's middle, looking toward the lens with the mount underneath), as the one installed example on file has it; the maker gives two positions and the other puts it 0.13 in to the right and 0.17 in further forward."],"ledger":["cloud-defensive-rein.length","cloud-defensive-rein.head_diameter","cloud-defensive-rein.body_diameter","cloud-defensive-rein.axis_above_mount","cloud-defensive-rein.tail_x","cloud-defensive-rein.lug_x","cloud-defensive-rein.lug_spacing","cloud-defensive-rein.mount_length","cloud-defensive-rein.mount_width","cloud-defensive-rein.mount_thickness","cloud-defensive-rein.mount_row_offset","cloud-defensive-rein.foot_front_x","cloud-defensive-rein.foot_spacing","cloud-defensive-rein.foot_length","cloud-defensive-rein.lens_diameter","cloud-defensive-rein.tail_button_diameter"]},"profiles":{"side":{"plane":"xy","origin":"on the body's axis at the tail cap's rear face (the photo's column 167.2: the face behind its rim's arc); the app adds where that is on the mount","offset":{"x":"tail_x","y":"axis_above_mount"},"points":[[-0.238,0.057],[-0.238,-0.057],[-0.234,-0.06],[-0.223,-0.167],[-0.205,-0.261],[-0.175,-0.34],[-0.138,-0.413],[-0.091,-0.492],[-0.056,-0.528],[-0.023,-0.535],[-0.001,-0.532],[0.014,-0.535],[0.047,-0.535],[0.051,-0.532],[0.076,-0.535],[0.087,-0.532],[0.343,-0.532],[0.409,-0.543],[0.413,-0.522],[0.841,-0.523],[0.849,-0.519],[0.852,-0.523],[0.917,-0.526],[0.95,-0.516],[0.979,-0.495],[0.997,-0.499],[1.166,-0.499],[1.17,-0.496],[1.22,-0.499],[1.253,-0.492],[1.26,-0.496],[1.285,-0.493],[1.314,-0.496],[1.321,-0.493],[1.325,-0.496],[1.328,-0.489],[1.346,-0.493],[1.379,-0.479],[1.384,-0.474],[1.384,-0.46],[1.397,-0.452],[1.829,-0.453],[1.833,-0.456],[1.876,-0.439],[1.993,-0.439],[1.997,-0.436],[2.032,-0.443],[2.036,-0.44],[2.224,-0.44],[2.263,-0.43],[2.291,-0.45],[2.316,-0.457],[2.337,-0.454],[2.341,-0.457],[2.38,-0.457],[2.383,-0.454],[2.415,-0.454],[2.419,-0.457],[2.426,-0.454],[2.475,-0.454],[2.479,-0.457],[2.482,-0.454],[2.496,-0.457],[2.507,-0.454],[2.51,-0.457],[2.532,-0.454],[2.535,-0.458],[2.549,-0.454],[2.56,-0.458],[2.574,-0.454],[2.648,-0.454],[2.651,-0.458],[2.658,-0.454],[2.746,-0.455],[2.775,-0.458],[2.799,-0.445],[2.834,-0.438],[2.845,-0.441],[3.882,-0.44],[3.917,-0.434],[3.93,-0.437],[3.939,-0.432],[3.948,-0.41],[3.994,-0.499],[4.035,-0.536],[4.049,-0.559],[4.065,-0.574],[4.096,-0.587],[4.106,-0.581],[4.123,-0.581],[4.127,-0.574],[4.137,-0.574],[4.144,-0.581],[4.147,-0.577],[4.163,-0.599],[4.192,-0.624],[4.23,-0.644],[4.261,-0.647],[4.295,-0.647],[4.298,-0.644],[4.36,-0.651],[4.367,-0.648],[4.47,-0.648],[4.473,-0.644],[4.48,-0.648],[4.49,-0.644],[4.517,-0.648],[4.589,-0.644],[4.593,-0.648],[4.695,-0.648],[4.739,-0.654],[4.746,-0.648],[4.753,-0.651],[4.756,-0.648],[5.035,-0.648],[5.038,-0.645],[5.041,-0.648],[5.055,-0.645],[5.177,-0.648],[5.187,-0.645],[5.261,-0.651],[5.268,-0.648],[5.336,-0.651],[5.349,-0.645],[5.363,-0.648],[5.373,-0.645],[5.561,-0.648],[5.565,-0.651],[5.578,-0.648],[5.591,-0.651],[5.618,-0.648],[5.622,-0.651],[5.632,-0.645],[5.635,-0.648],[5.672,-0.645],[5.699,-0.648],[5.712,-0.645],[5.726,-0.648],[5.746,-0.645],[5.749,-0.648],[5.752,-0.645],[5.776,-0.648],[6.067,-0.645],[6.073,-0.648],[6.083,-0.645],[6.087,-0.648],[6.097,-0.645],[6.1,-0.648],[6.113,-0.645],[6.136,-0.652],[6.156,-0.648],[6.181,-0.627],[6.181,-0.594],[6.203,-0.596],[6.225,-0.578],[6.245,-0.539],[6.268,-0.46],[6.288,-0.349],[6.301,-0.221],[6.304,-0.1],[6.308,-0.096],[6.308,0.097],[6.304,0.1],[6.301,0.221],[6.288,0.349],[6.258,0.5],[6.238,0.556],[6.225,0.573],[6.225,0.579],[6.203,0.598],[6.181,0.593],[6.181,0.626],[6.156,0.647],[6.136,0.651],[6.113,0.645],[6.07,0.648],[6.067,0.645],[6.017,0.646],[6.013,0.649],[6,0.646],[5.996,0.649],[5.986,0.646],[5.98,0.649],[5.96,0.646],[5.953,0.65],[5.926,0.647],[5.923,0.65],[5.92,0.647],[5.809,0.648],[5.806,0.645],[5.803,0.648],[5.598,0.647],[5.591,0.65],[5.578,0.647],[5.565,0.651],[5.561,0.647],[5.447,0.649],[5.443,0.645],[5.363,0.649],[5.349,0.646],[5.346,0.65],[5.339,0.646],[5.332,0.65],[5.322,0.647],[5.319,0.65],[5.315,0.647],[5.268,0.647],[5.261,0.651],[5.187,0.645],[5.096,0.649],[5.089,0.646],[5.082,0.649],[5.079,0.646],[5.072,0.649],[5.038,0.643],[5.035,0.646],[4.766,0.649],[4.756,0.646],[4.749,0.65],[4.746,0.646],[4.739,0.653],[4.729,0.653],[4.695,0.647],[4.593,0.648],[4.589,0.645],[4.517,0.649],[4.49,0.646],[4.48,0.649],[4.476,0.646],[4.367,0.647],[4.36,0.65],[4.298,0.644],[4.295,0.648],[4.261,0.648],[4.23,0.645],[4.192,0.626],[4.147,0.576],[4.144,0.579],[4.137,0.573],[4.127,0.573],[4.123,0.58],[4.106,0.58],[4.096,0.587],[4.065,0.574],[4.049,0.559],[4.035,0.536],[3.994,0.499],[3.948,0.411],[3.939,0.433],[3.93,0.438],[3.917,0.435],[3.913,0.438],[3.588,0.441],[3.584,0.438],[3.525,0.438],[3.518,0.442],[3.512,0.439],[3.498,0.442],[3.494,0.439],[3.292,0.441],[3.289,0.437],[3.09,0.442],[3.083,0.439],[3.072,0.443],[3.069,0.439],[3.065,0.443],[3.058,0.439],[3.055,0.443],[3.048,0.439],[3.041,0.443],[3.034,0.44],[3.009,0.443],[3.006,0.44],[2.845,0.441],[2.834,0.438],[2.799,0.445],[2.775,0.459],[2.694,0.456],[2.69,0.453],[2.51,0.458],[2.507,0.454],[2.496,0.458],[2.482,0.455],[2.479,0.458],[2.475,0.455],[2.426,0.455],[2.419,0.459],[2.387,0.452],[2.341,0.456],[2.337,0.453],[2.316,0.456],[2.291,0.45],[2.263,0.43],[2.224,0.44],[2.036,0.438],[2.032,0.442],[1.997,0.435],[1.993,0.439],[1.876,0.44],[1.833,0.457],[1.78,0.451],[1.397,0.451],[1.384,0.46],[1.384,0.473],[1.379,0.478],[1.346,0.492],[1.328,0.489],[1.325,0.496],[1.321,0.493],[1.314,0.496],[1.285,0.493],[1.26,0.497],[1.253,0.493],[1.21,0.5],[1.206,0.497],[0.997,0.499],[0.979,0.496],[0.95,0.517],[0.917,0.527],[0.863,0.524],[0.849,0.518],[0.841,0.521],[0.551,0.524],[0.547,0.52],[0.413,0.522],[0.411,0.541],[0.398,0.542],[0.343,0.533],[0.241,0.534],[0.237,0.53],[0.014,0.536],[-0.001,0.533],[-0.023,0.536],[-0.048,0.533],[-0.076,0.511],[-0.08,0.501],[-0.105,0.47],[-0.164,0.363],[-0.205,0.26],[-0.223,0.167],[-0.234,0.06]],"features":{"latch_face":[[[0.464,0.211],[0.794,0.208],[0.794,-0.021],[0.464,-0.019]]],"latch_edge":[[[0.496,0.622],[0.809,0.619],[0.809,0.527],[0.496,0.53]],[[0.434,-0.524],[0.762,-0.524],[0.762,-0.627],[0.434,-0.627]]],"bezel_flat":[[[5.315,0.001],[6.22,-0.004],[6.22,-0.28],[5.315,-0.276]]],"grip_flat":[[[1.547,0.176],[2.859,0.167],[2.859,-0.177],[1.547,-0.171]]],"seams":[[[0.405,0.568],[0.427,0.568],[0.427,0.52],[0.405,0.52]],[[4.712,0.665],[4.732,0.665],[4.732,0.618],[4.712,0.618]]]},"scaleRefs":["cloud-defensive-rein.body_diameter","cloud-defensive-rein.length"],"inputs":{"cloud-defensive-rein.body_diameter":0.881,"cloud-defensive-rein.length":6.17},"tolerance":0.003,"photo":"references/cloud-defensive-rein 07a3e75fa1b3 (Rifle Supply CLDREIN-3-0-DFS650-BLK_1_HR: the black light standing lens up on white, 2000 x 2000; a quarter turn of f23602b1d23a (lens to the right))","method":"luminance < 200, inside [60, 150, 2000, 640], 2 boxes excluded, largest piece, holes filled; the turned body alone: at each column the smaller of the dark run's reach above and below the tube's axis, taken both ways; scale from cloud-defensive-rein.body_diameter = 0.881 in, the tube's own width column by column: 262.1 px over columns 900–1030, 262.7 px over columns 1060–1190; a line through them (rms 0.29 px) changes +0.7% from column 949 to 1190, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1855)/width, the lens's axis taken to meet the image at column 1855; 304.2 px/in there. The axis is the tube's centre line (tilt -0.33°, rms 0.11 px). Lengths then scaled by 1.0166 so that the end faces are cloud-defensive-rein.length = 6.17 in apart: at the tube's scale they read 6.069 (-1.6%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.138 in over radius 0.647 (rms 0.001), the rear end's rim sags 0.232 in over radius 0.532 (rms 0.007); origin at column 167.2 of the photo, on the tube's axis; Douglas-Peucker at 0.003 in with the extremes kept: 341 points (IoU 0.998 with the full outline); checks: width 6.546 ± 0.038; the min end's face: the silhouette's tip at -0.236 less its rim's arc, 0.267 in of sag at radius 0.531758 (the end is seen from 26.7° off square; arc fitted over 118 rows, rms 0.001) 0.031 ± 0.005; the max end's face: the silhouette's tip at 6.308 less its rim's arc, 0.143 in of sag at radius 0.646986 (the end is seen from 12.4° off square; arc fitted over 121 rows, rms 0.001) 6.165 ± 0.035; features through the same placement (latch_face: one of the oval ribbed latches on the switch housing, facing the camera: its length along the body and its width round it. It shows at columns 240 to 331; boxed at the columns of the two seen edge-on (it lies 0.6 in nearer the camera than the axis); latch_edge: two more of them seen edge-on, standing off the housing above and below (the boxes that are cut from the outline): how far they stand out. A fourth is taken to be behind (they are a quarter turn apart); bezel_flat: one of the bezel's flats (six, 60 degrees apart: three show, at 49 degrees above square to the camera, 11 below and 71 below): its length and, across it, its width as seen 11 degrees round from square. It shows at columns 1632 to 1902; boxed 46 px toward the lens (0.62 in nearer the camera, seen 14 degrees off square there), which runs it out through the bezel's front; grip_flat: the flat along the grip section that carries the wordmark, facing the camera square on: it cuts the two bands and just into the waist between them. It shows at columns 545 to 915; boxed 49 px toward the lens (0.42 in nearer the camera, seen 22 degrees off square there); seams: the two joints that show as dark lines round the body, each boxed where its line meets the silhouette's upper edge: the tail cap against the switch housing, and the bezel against the head's rear half. How deep the lines are isn't measured) (tools/trace.py)","via":"harvest","note":"The turned body alone, lens to the right: tail cap, switch housing, collar, the banded grip section, the plain tube, the head and its bezel. The latches on the switch housing, the cable and the remote switch aren't in it; the ends run past the two end faces by their rims' arcs (the faces are at x 0 and at the published length). The photo sees the light from 12 degrees off square at the lens and 27 at the tail, so each shoulder's rim shows as a short arc: steps read as ramps up to 0.06 in long."}},"gaps":[{"what":"How far the mount's T-nuts reach inside the handguard (reach_inside)","need":"A figure from Cloud Defensive, or a photo of the mount tightened on a handguard seen from inside"},{"what":"A second source for each colour (each rests on one studio's two pictures of one light)","need":"A seller's own photographs of the FDE, Earth Brown and OD Green lights under one light, or the maker's colour reference"},{"what":"The weight without the battery, and the mount's own weight","need":"A maker's figure or a reviewer's scale"},{"what":"The mounting feet's width across the body, and a straight end view of the light","need":"A photo of the body from an end, or the Scout mounting pattern's drawing"},{"what":"Everything about the inline mount is read off two photos (± 0.02 to 0.04 in)","need":"The maker's drawing or figures for the mount (TOR-MLOKINLINE BLK): none is published"},{"what":"The Picatinny mount the light shipped with at its 2022 launch (two sellers still list it)","need":"Nothing: the maker's page now lists the inline M-LOK mount, and that is what is modelled"}]},"cmmg-lower-parts-kit":{"id":"cmmg-lower-parts-kit","name":"Lower Parts Kit, AR15","manufacturer":"CMMG","sku":"55CA6C5","url":"https://cmmg.com/lower-parts-kit-ar15","category":"lpk","description":"CMMG's lower parts kit with a trigger, a grip and a trigger guard, \"in convenient color-coded packets to simplify assembly\" (CMMG). Kit Includes: Bolt catch/roll pin; Bolt catch plunger/spring; Trigger guard/roll pin; Trigger; Trigger spring; Disconnector; Disconnector spring; Hammer; Hammer spring; Trigger/hammer retaining pins; Safety, detent, & spring; Magazine catch, spring, & release button; Pivot/takedown pins, detents, & springs; A2-style pistol grip/grip screw & washer; Buffer retainer/spring. One product over the parts kit's, the trigger's, the grip's and the trigger guard's slots (D33). Its sellers describe a \"Mil-Spec trigger that offers a conventional, single-stage 6 to 6½ lb. service rifle pull\" (AR15Discounts) and \"standard small pins\" (Alexander's).","weight":"cmmg-lower-parts-kit.weight","occupies":["trigger","grip","trigger_guard"],"integral":[],"brings":["selector"],"seats":{},"requires":[],"anchors":{"lpk":{"origin":[0,0,0],"note":"On the receiver's left face, level with the takedown pin: the controls stand out from it toward −Z, and the trigger, the grip and the guard stand on the receiver's middle, half the body's width across."},"face":{"origin":["{.trigger_face_x}","{std.ar15.trigger_pin_y}","{std.ar15.lower_body_width} / 2"],"note":"The trigger's face, where a finger lands: length of pull is read from here (the trigger slot is occupied by this product). On the receiver's middle, in the kit's frame."}},"interfaces":{"lpk":{"type":"ar15.lpk","role":"kit","anchor":"lpk","params":{},"flips":false}},"materials":{"controls":{"label":"Controls and trigger","finish":"steel","recolorable":false,"color":"placeholder-black","note":"\"Material: Steel / Finish: Black\" (Wing Tactical, of the kit); \"Color Black\" (Primary Arms). Sold in black only (55CA6C5). The Army's trigger is a steel investment casting (8448592, note 1). On CMMG's photo of the kit laid out (ebb3eeae3c78) the trigger, hammer and disconnector, the selector, the bolt catch, the magazine catch and its button, the two receiver pins, the buffer retainer, the grip screw and the guard's roll pin are one black, matte on the cast pieces: a black, not fitted to a photo. Bare steel there, and not drawn: the springs, the small detents, the grip screw's lock washer."},"grip":{"label":"A2-style pistol grip","finish":"polymer","recolorable":false,"color":"placeholder-polymer-black","note":"\"A2-style pistol grip\" (CMMG); \"molded-polymer A2 pistol grip\" (AR15Discounts). Black on CMMG's photo of the kit."},"guard":{"label":"Trigger guard","finish":"anodized","recolorable":false,"color":"placeholder-black","note":"No page states what CMMG's guard is made of (\"Trigger guard/roll pin\"). The Army drawing's is 7075-T6, hard anodized, lusterless black (8448588, material and note 4): drawn so, black as CMMG's photo has it."},"plunger":{"label":"Trigger guard's plunger","finish":"steel","recolorable":false,"color":"stainless-natural","note":"The spring-loaded plunger in the guard's front end, bare bright steel on CMMG's photo of the kit laid out (ebb3eeae3c78: the guard at the lower right, its plunger standing out of its front end, silver against the black guard). The guard's roll pin is with the controls: black."}},"components":{"controls":{"label":"Bolt catch, magazine release, pins","material":"controls"},"selector":{"label":"Selector","material":"controls"},"trigger":{"label":"Trigger","material":"controls"},"grip":{"label":"A2-style pistol grip","material":"grip"},"guard":{"label":"Trigger guard","material":"guard"}},"geometry":{"components":{"grip":"cmmg-lower-parts-kit.grip.glb","trigger":"cmmg-lower-parts-kit.trigger.glb","guard":"cmmg-lower-parts-kit.guard.glb","selector":"cmmg-lower-parts-kit.selector.glb"},"approximations":["CMMG publishes no dimension of this kit. Its pieces are drawn as the Army's drawings' pieces, on the strength of its sellers' words (\"All parts meet or exceed Mil-Spec\", Wing Tactical; \"Fits Mil-spec Ar-15/M16 Lower Receivers\", AR15Discounts), and stand where the Army's drawing of the lower receiver (8448608) holds them, whatever lower the build has.","The grip is the Army's pistol grip (drawing 9349127: CMMG says \"A2-style pistol grip\", AR15Discounts \"molded-polymer A2 pistol grip\"; CMMG's photo shows its checkered panel and finger rest): its side view traced at the size of a service rifle's A2 grip (a US Marine Corps photo of an M4A1 in its pin frame: its lowest point 4.92 below the pins, its heel 2.11 behind the takedown pin), swept along its raked axis across its bottom view (1.270 over the knurl; stretched along to the side view's depth, its knurl's teeth bridged) and narrowed to its front view (the top block's .885), its edges rounded to the block's .06; the checkered panels are plain pads on its two sides (the side view's panel outline, picked on the drawing, standing 0.03 out of the body: the depth of the knurl's teeth on the traced bottom view). It sits with its top face on the receiver's underside (1.318 below the deck) and its front face on the rear face of the guard's ears (2.300 ahead of the receiver's rear face), and the slot the receiver's lug stands in is cut along its top at the drawing's .380 +.005, 0.004 off the standard's .375 lug all round, open through the front face. That rifle's grip leans about a degree nose-up of the drawing's: the model's base is 0.06 in above its and the heel 0.05 behind. The drawing's one stated size across the side view (1.275, the front face) would make the grip 3% larger than both photographed grips are, and is not used. On the lowers drawn with the standard lug the grip shares nothing with BCA's and 0.03 cubic inches with the Workhorse, whose own seat and ears stand 0.025 and 0.045 off the drawing's; on a lower still drawn as one slab at its lug the walls beside the slot would stand inside it. Not drawn: the checkering itself and the backstrap's grooves, the slot's own floor (Section C-C), the core, the screw and its washer.","The trigger is the Army's (drawing 8448592: \"Mil-Spec trigger\", AR15Discounts; \"standard mil-spec single-stage trigger\", Alexander's): its side elevation traced, .290 across, with the bosses round its pivot, its edges rounded to the drawing's .031, turned 1° back about its pin to where Aero's photo has a mil-spec trigger at rest. Not drawn: the blade's face curved across (.375 R), the disconnector's slot and spring well, the disconnector, the hammer and the springs.","The trigger guard is the Army's (drawing 8448588: CMMG's photo shows a flat guard with a round end and a plunger; its install article has \"the ball detent end ... closet to the magazine well\"): built from the drawing's stated sizes, level between the receiver's two guard holes, its roll pin a plain rod across the receiver's rear ears (0.659 across their outside faces, the standard's) and its plunger's tip a rod at the receiver's front hole's diameter as far as that hole's spotface, on the right. Not drawn: the holes' countersinks, the plunger's bore behind its tip and its spring; how far the plunger really stands out and the roll pin's own length aren't on file."],"ledger":["cmmg-lower-parts-kit.takedown_pin_head_d","cmmg-lower-parts-kit.takedown_pin_head_t","cmmg-lower-parts-kit.pivot_pin_head_d","cmmg-lower-parts-kit.pivot_pin_head_flat","cmmg-lower-parts-kit.pivot_pin_head_t","cmmg-lower-parts-kit.pin_head_dome_r","cmmg-lower-parts-kit.selector_hub_d","cmmg-lower-parts-kit.selector_pointer_reach","cmmg-lower-parts-kit.selector_pointer_angle","cmmg-lower-parts-kit.selector_paddle_width","cmmg-lower-parts-kit.selector_paddle_reach","cmmg-lower-parts-kit.selector_serration_height","cmmg-lower-parts-kit.selector_lever_t","cmmg-lower-parts-kit.bolt_catch_paddle_rear_x","cmmg-lower-parts-kit.bolt_catch_paddle_front_x","cmmg-lower-parts-kit.bolt_catch_paddle_bottom_y","cmmg-lower-parts-kit.bolt_catch_paddle_top_y","cmmg-lower-parts-kit.bolt_catch_t","cmmg-lower-parts-kit.magazine_release_w","cmmg-lower-parts-kit.magazine_release_h","cmmg-lower-parts-kit.magazine_release_standoff","cmmg-lower-parts-kit.grip_top_y","cmmg-lower-parts-kit.grip_front_x","cmmg-lower-parts-kit.grip_slot_width","cmmg-lower-parts-kit.grip_depth","cmmg-lower-parts-kit.grip_rake","cmmg-lower-parts-kit.grip_width","cmmg-lower-parts-kit.grip_body_width","cmmg-lower-parts-kit.guard_length","cmmg-lower-parts-kit.guard_hole_spacing","cmmg-lower-parts-kit.guard_hole_from_end","cmmg-lower-parts-kit.guard_end_height","cmmg-lower-parts-kit.guard_hole_above_bottom","cmmg-lower-parts-kit.guard_bar_t","cmmg-lower-parts-kit.guard_end_r","cmmg-lower-parts-kit.guard_fillet_r","cmmg-lower-parts-kit.guard_width","cmmg-lower-parts-kit.guard_front_hole_y","cmmg-lower-parts-kit.guard_edge_break","cmmg-lower-parts-kit.grip_edge_r","cmmg-lower-parts-kit.grip_height","cmmg-lower-parts-kit.trigger_rest_angle","cmmg-lower-parts-kit.trigger_face_x","cmmg-lower-parts-kit.trigger_edge_r","std.ar15.trigger_pin_x","std.ar15.trigger_pin_y","std.ar15.trigger_body_width","std.ar15.trigger_boss_d","std.ar15.trigger_boss_length","std.ar15.trigger_guard_rear_x","std.ar15.trigger_guard_rear_y","std.ar15.trigger_guard_rear_hole_d","std.ar15.trigger_guard_front_hole_d","std.ar15.trigger_guard_front_spotface_floor","std.ar15.trigger_guard_ears_width","std.ar15.lower_body_width","std.ar15.deck_y","std.ar15.receiver_rear_x","std.ar15.grip_seat_below_deck","std.ar15.grip_lug_front_from_rear_face","std.ar15.grip_lug_width","std.ar15.grip_lug_length","std.ar15.grip_lug_depth","std.ar15.grip_lug_face_from_pin","std.ar15.grip_lug_face_angle","std.ar15.mag_catch_x","std.ar15.mag_catch_y","std.ar15.selector_x","std.ar15.selector_y","std.ar15.hammer_pin_x","std.ar15.hammer_pin_y","std.ar15.takedown_hole_d","std.ar15.pivot_hole_d","std.ar15.selector_hole_d","std.ar15.fcg_pin_hole_d"]},"profiles":{"grip_side":{"plane":"xy","origin":"the theoretical corner of the top face (y = 0) and the front face (x = 0); the part frame adds grip_front_x and grip_top_y, where a standard lower holds them","offset":{"x":"grip_front_x","y":"grip_top_y"},"points":[[-3.333,-3.198],[-3.311,-3.261],[-3.266,-3.316],[-3.266,-3.353],[-3.227,-3.37],[-1.639,-3.766],[-1.62,-3.785],[-1.45,-3.796],[-1.339,-3.748],[-1.278,-3.679],[-1.278,-3.627],[-1.333,-3.553],[-1.359,-3.468],[-1.348,-3.324],[-0.974,-2.65],[-0.926,-2.609],[-0.922,-2.565],[-0.77,-2.302],[-0.724,-2.252],[-0.62,-2.196],[-0.32,-2.163],[-0.278,-2.128],[-0.278,-2.05],[-0.389,-1.902],[-0.411,-1.846],[-0.418,-1.72],[-0.378,-1.613],[-0.178,-1.25],[-0.139,-1.218],[-0.004,-1.205],[0,-0.676],[-0.011,-0.239],[-0.083,-0.067],[-0.109,-0.067],[-0.154,-0.019],[-0.246,0],[-0.828,0],[-1.441,-0.017],[-1.459,-0.28],[-1.481,-0.365],[-1.552,-0.517],[-1.646,-0.641],[-1.741,-0.657],[-1.741,-0.698],[-1.711,-0.72],[-1.722,-0.765],[-1.985,-1.139],[-2.018,-1.161],[-2.018,-1.187],[-2.4,-1.735],[-2.441,-1.768],[-2.441,-1.791],[-3.17,-2.842],[-3.226,-2.894],[-3.226,-2.92],[-3.292,-3.005],[-3.326,-3.076]],"features":{"knurl":[[[-1.505,-0.961],[-1.124,-1.091],[-0.78,-1.217],[-0.717,-1.383],[-0.728,-1.505],[-0.902,-1.802],[-1.05,-2.05],[-1.15,-2.246],[-1.372,-2.591],[-1.568,-2.987],[-1.691,-3.209],[-1.791,-3.309],[-1.987,-3.32],[-2.209,-3.257],[-2.457,-3.183],[-2.653,-3.124],[-2.802,-3.061],[-2.839,-2.939],[-2.828,-2.839],[-2.753,-2.716],[-2.653,-2.542],[-2.457,-2.246],[-2.261,-1.976],[-1.987,-1.605],[-1.742,-1.235],[-1.594,-1.035]]]},"scaleRefs":["cmmg-lower-parts-kit.grip_height","cmmg-lower-parts-kit.grip_depth"],"inputs":{"cmmg-lower-parts-kit.grip_depth":3.284,"cmmg-lower-parts-kit.grip_height":3.8535},"tolerance":0.01,"photo":"references/aero-m4e1-lower be585e351439 (US Army TDP drawing 9349127 (Grip, Pistol) rev J, frame 1 of 2 (the user's M16 TDP scan, PDF page 33): the side view)","method":"luminance < 128, inside [2600, 2395, 3600, 3480], 3 boxes excluded, 1 polygons excluded, closing 3 px ×3, largest piece, holes filled, opening after the fill 15 px ×1, inset 3 px (half the outline's stroke); scale from cmmg-lower-parts-kit.grip_height = 3.8535 in (y-extent 1025 px → 266.0 px/in) and cmmg-lower-parts-kit.grip_depth = 3.284 in (x-extent 900 px → 274.1 px/in), which agree within 3.0%; mean 270.0 px/in; origin at x max, y max of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 57 points (IoU 0.995 with the full outline); checks: height 3.796 ± 0.059; width 3.333 ± 0.052; features through the same placement (knurl: the checkered panel on the grip's side (the same on both), its outline picked on a gridded crop of the view: its long edges along the grip's axis and the backstrap, its ends square to the axis, its corners round) (tools/trace.py)","via":"user","note":"The A2 grip's side: its level top face, the upright front face and the step under it, the front strap with its finger rest, the base square to the axis, the backstrap. The checkering, the backstrap's grooves and the section marks are inside the outline. Scaled by a service rifle's grip, not by the drawing's stated 1.275."},"grip_section":{"plane":"xz","origin":"the backstrap's end (x' = 0), centred across. A plan in the grip's own frame: x' square to its axis toward the front strap (grip_rake below the bore line), z across","offset":{},"points":[[0,-0.022],[0.036,-0.208],[0.111,-0.334],[0.297,-0.496],[0.451,-0.545],[0.452,-0.569],[0.604,-0.586],[0.643,-0.629],[0.857,-0.628],[0.887,-0.599],[0.996,-0.635],[1.201,-0.618],[1.241,-0.57],[1.262,-0.6],[1.323,-0.558],[1.372,-0.577],[1.458,-0.529],[1.958,-0.406],[2.148,-0.225],[2.157,-0.003],[2.14,0.223],[2.045,0.28],[1.951,0.404],[1.289,0.574],[1.273,0.605],[1.212,0.617],[1.213,0.584],[0.9,0.603],[0.874,0.635],[0.623,0.609],[0.559,0.565],[0.476,0.578],[0.43,0.54],[0.306,0.521],[0.078,0.281],[0.015,0.125]],"scaleRefs":["cmmg-lower-parts-kit.grip_width"],"inputs":{"cmmg-lower-parts-kit.grip_width":1.27},"tolerance":0.02,"photo":"references/aero-m4e1-lower be585e351439 (US Army TDP drawing 9349127 (Grip, Pistol) rev J, frame 1 of 2 (the user's M16 TDP scan, PDF page 33): the bottom view, along the grip's axis)","method":"luminance < 128, inside [2290, 3640, 2960, 4160], pieces ≥ 300 px, closing ×1, largest piece, holes filled, inset 3 px (half the outline's stroke); rotated +29.1° as declared; scale from cmmg-lower-parts-kit.grip_width = 1.27 in (y-extent 345 px → 272.0 px/in); origin at x min, y center of the outline; Douglas-Peucker at 0.02 in with the extremes kept: 36 points (IoU 0.987 with the full outline); checks: width 2.157 ± 0.036 (tools/trace.py)","via":"user","note":"The grip seen from below along its axis: the silhouette of every section square to the axis at once (the widest is the knurl's, 1.270), symmetric about its long axis. One scale reference (the stated width); its length is the check against the side view's depth square to the axis."},"grip_front":{"plane":"zy","origin":"the top face (y = 0, offset to grip_top_y), centred on the block; the grip's top face is level on a standard lower","offset":{"y":"grip_top_y"},"points":[[-0.686,-2.596],[-0.667,-3.36],[-0.61,-3.641],[-0.545,-3.747],[-0.391,-3.874],[-0.065,-3.878],[-0.038,-3.897],[0.327,-3.886],[0.429,-3.817],[0.515,-3.717],[0.553,-3.625],[0.594,-3.39],[0.621,-2.813],[0.594,-1.711],[0.53,-0.929],[0.439,-0.431],[0.446,-0.063],[0.41,-0.011],[0.315,0],[0,0],[-0.431,-0.017],[-0.446,-0.412],[-0.53,-0.792],[-0.617,-1.381],[-0.67,-2.038]],"scaleRefs":["cmmg-lower-parts-kit.grip_body_width"],"inputs":{"cmmg-lower-parts-kit.grip_body_width":0.885},"tolerance":0.015,"photo":"references/aero-m4e1-lower be585e351439 (US Army TDP drawing 9349127 (Grip, Pistol) rev J, frame 1 of 2 (the user's M16 TDP scan, PDF page 33): the front view, along the top face)","method":"luminance < 128, inside [4625, 2398, 5030, 3440], 6 boxes excluded, pieces ≥ 300 px, closing ×1, largest piece, holes filled, inset 3 px (half the outline's stroke); scale from cmmg-lower-parts-kit.grip_body_width = 0.885 in (median width over 0.03–0.09 of the height from the top, 232–235 px 233 px → 263.3 px/in); origin at x center, y max of the outline (x over 0.03–0.09 of the height from the top); Douglas-Peucker at 0.015 in with the extremes kept: 25 points (IoU 0.992 with the full outline); checks: height 3.897 ± 0.067 in vs cmmg-lower-parts-kit.grip_height 3.8535 ± 0.0315 (conflict): agrees; width 1.307 ± 0.025 in vs cmmg-lower-parts-kit.grip_width 1.27 ± 0.02 (confirmed): agrees (tools/trace.py)","via":"user","note":"The grip seen from the front: the block .885 wide below the top face, the body flaring out under it, the bottom's corners rounded. Scaled by the block alone; its height against the side view's is the check (two views of one drawing, two stated sizes)."},"trigger":{"plane":"xy","origin":"the pivot hole's centre (the trigger pin's axis), +x toward the muzzle","offset":{},"points":[[-1.204,-0.232],[-1.187,-0.265],[-0.105,-0.271],[-0.09,-0.286],[-0.09,-0.371],[-0.052,-0.403],[-0.046,-0.457],[-0.09,-0.552],[-0.125,-0.701],[-0.113,-0.98],[-0.078,-1.095],[0.005,-1.247],[0.005,-1.272],[0.152,-1.423],[0.203,-1.433],[0.224,-1.415],[0.224,-1.377],[0.125,-1.237],[0.068,-1.053],[0.062,-0.946],[0.078,-0.831],[0.095,-0.807],[0.125,-0.809],[0.125,-0.781],[0.1,-0.761],[0.103,-0.736],[0.186,-0.593],[0.247,-0.528],[0.378,-0.427],[0.493,-0.381],[0.493,-0.181],[0.514,-0.132],[0.769,-0.133],[0.788,0.044],[0.292,0.049],[0.263,0.011],[0.2,0.005],[0.163,0.025],[0.098,0.135],[-0.016,0.163],[-0.108,0.132],[-0.144,0.092],[-0.163,0.038],[-0.197,0.008],[-0.225,0.005],[-0.263,0.008],[-0.298,0.049],[-0.333,0.056],[-1.12,0.059],[-1.19,0.046],[-1.201,0.038]],"scaleRefs":["std.ar15.trigger_tail_behind_pivot"],"inputs":{"std.ar15.trigger_tail_behind_pivot":1.2025},"tolerance":0.01,"photo":"references/aero-m4e1-lower 1dabf089edf8 (US Army TDP drawing 8448592 (Trigger) rev L (the user's M16 TDP scan, PDF page 43): the side elevation)","method":"luminance < 128, inside [2650, 2815, 3330, 3345], 4 boxes excluded, closing ×2, the piece at [3051, 3000], holes filled, opening after the fill 9 px ×1, inset 2 px (half the outline's stroke); frame from the reviewed holes pivot, tail (315.2 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.01 in with the extremes kept: 51 points (IoU 0.985 with the full outline); checks: −y_min 1.433 ± 0.007 in vs std.ar15.trigger_blade_below_pivot 1.45 ± 0.02 (confirmed): agrees; −x_min 1.204 ± 0.007 in vs std.ar15.trigger_tail_behind_pivot 1.2025 ± 0.0075 (confirmed): agrees (tools/trace.py)","via":"user","note":"The trigger's side: its tail, the body, the blade's front and back curves to its lowest point. As the drawing's elevation has it (the tail level); the model turns it trigger_rest_angle about the pin."}},"gaps":[{"what":"CMMG's own figures: no page gives a dimension, a pin size or a trigger pull for this kit, and the maker states no weight","need":"CMMG's drawing or spec sheet, or the kit weighed out of its pack; until then the Army's drawings stand for its parts and Primary Arms' 7 oz for its weight"},{"what":"the selector lever's thickness (only its serrations are dimensioned on the Army's drawing)","need":"the plate's thickness: drawing 9381367's side view read at higher resolution, or a maker's figure"},{"what":"the grip's lean and size within about 1.5%: on the service rifle's photo an A2 grip stands about a degree nose-up of the Army drawing's side view with its top level (Aero's photo of its own: 1.7°), and the drawing's stated 1.275 across its front face is 0.05 more than the two photographed grips have there","need":"a straight side photo of a bare A2 grip with a scale in its plane, and the Army drawing's Section C-C (frame 2) read for the slot's floor and what the 1.275 spans"},{"what":"where the kit's weight sits: it is put at the middle of everything drawn, most of which is the grip, though most of the weight is the steel in the receiver","need":"a published weight for an A2 grip alone (the model is solid where the grip is hollow, so a density won't do); the grip and the guard then become lumps and the steel takes the rest"},{"what":"where CMMG's own trigger rests, and its hammer and disconnector","need":"a pin-framed side photo of a lower built with this kit; the Army's drawings 8448613 (hammer) and 8448635 (disconnector) for the two not drawn"}]},"cmmg-safety-selector":{"id":"cmmg-safety-selector","name":"Safety Selector, AR15","manufacturer":"CMMG","sku":"55CA741","url":"https://cmmg.com/safety-selector-ar15","category":"selector","description":"The plain selector a rifle comes with: one lever, on the left side, turned a quarter turn between safe and fire. CMMG: \"AR-15 Single sided safety selector. Featuring a mil-spec style selector lever and standard 90° throw operation.\" and \"meets or exceeds mil-spec\". Steel with a parkerized finish (Sportsman's Warehouse, of this part).","weight":"cmmg-safety-selector.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"selector":{"origin":[0,0,0],"note":"Selector frame: on its axis, at the middle of the length of shaft that lies in the receiver (the receiver's mid-plane when it is in), with the selector on SAFE: +x toward the muzzle, +y up, +z out of the rifle's right side. The lever's inner face bears on the receiver's left side, half the standard body's width (std.ar15.lower_body_width) toward -z; the shaft's far end stands out of the right side by its length less that width."}},"interfaces":{"selector":{"type":"ar15.selector","role":"selector","anchor":"selector","params":{},"flips":false,"note":"CMMG: \"standard 90° throw operation\"; Sportsman's Warehouse: \"For standard AR-15-style configurations\" (https://www.sportsmans.com/shooting-gear-gun-supplies/gun-parts-accessories/gun-parts-magazines/rifle-parts/cmmg-ar15-single-sided-safety-selector-black/p/2001659). Drawn on SAFE: the pointer forward at the receiver's SAFE mark, the thumb piece back over the grip, as a mil-spec selector sits with the marks in frame (references/rise-lpk f008e4862517). Nothing is posed for FIRE."}},"materials":{"body":{"label":"Selector","finish":"phosphate","recolorable":false,"color":"steel-parkerized","note":"Steel; \"Parkerized finish\" and \"Color Black\" (Sportsman's Warehouse, of this part, MPN 55CA741); \"Safety selector for AR-15. Black.\" (Impact Guns). CMMG's own page states no finish. Sold in the one finish. The Army's drawing asks for a carburized investment casting of 8620 with \"PROTECTIVE FINISH 5.3.1.2 OF MIL-STD-171\" (notes 1, 7, 11; which finish that number is isn't read from a source on file). On its one photo (b9b588162284, Sportsman's copy at 1200 px) the whole part is one dark grey, matte and a little grainy, lighter where the lamp falls on the thumb piece's edge: a parkerizing, drawn in the catalog's parkerized grey (steel-parkerized, fitted on another maker's barrel). Not fitted to this photo: its lit flats read #60615f to #626360 on Sportsman's copy and its shaded ones #2c2d2c, and CMMG's own copy of the same picture is darker throughout: one photograph under hard light, in two tone curves."}},"components":{},"geometry":{"model":"cmmg-safety-selector.glb","components":{},"approximations":["Every size is the Army's drawing of the standard selector (9381367, sheet 1), not a measurement of CMMG's part: CMMG says its selector \"meets or exceeds mil-spec\" and publishes no figure. Its one photo, a three-quarter view, agrees with the drawing in what it shows (the hub a thin plate with its face plain round the axis, the thumb piece a thick slab beginning below the axis, stepped terraces along it, the relief's step under it) and gives no size.","Inside the receiver the shaft is a plain cylinder of the drawing's diameter: the cut for the trigger's tail (CMMG's is a semi-automatic's, a flat across the middle, in its photo), the detent's holes and the neck beside the lever aren't drawn. None of it shows.","The lever's edges are broken by a few thousandths (the drawing: .010 max); the casting's draft and the maker's mark the drawing puts on the thumb piece's edge aren't drawn.","Drawn on SAFE only: the pointer forward, the thumb piece back over the grip.","Its weight is worked out from the drawing's sizes as steel (the ledger's note): no page states one."],"ledger":["cmmg-safety-selector.shaft_d","cmmg-safety-selector.shaft_length","cmmg-safety-selector.shaft_end_chamfer","cmmg-safety-selector.hub_d","cmmg-safety-selector.hub_t","cmmg-safety-selector.pointer_reach","cmmg-safety-selector.pointer_angle","cmmg-safety-selector.pointer_fillet_r","cmmg-safety-selector.paddle_width","cmmg-safety-selector.paddle_start","cmmg-safety-selector.lever_reach","cmmg-safety-selector.paddle_base_t","cmmg-safety-selector.paddle_relief","cmmg-safety-selector.paddle_relief_start","cmmg-safety-selector.lever_standoff","std.ar15.lower_body_width","std.ar15.selector_hole_d"]},"profiles":{},"gaps":[{"what":"its weight: no page states one","need":"CMMG's or a seller's figure for 55CA741, or a scale reading of one"},{"what":"any size of CMMG's own part: all are the Army drawing's","need":"a straight view of CMMG's selector along its axis and one edge-on, to hold the drawing's lever to it; its only photo is one three-quarter view"}]},"daniel-defense-103-barrel":{"id":"daniel-defense-103-barrel","name":"CHF Chrome Lined 5.56 AR-15 Barrel - Carbine - Government - 10.3\"","manufacturer":"Daniel Defense","sku":"07-077-16176-018","url":"https://www.primaryarms.com/daniel-defense-5-56-10-3-17-chf-barrel-carbine-length-gas-system-07-077-16176-018","category":"barrel","description":"Daniel Defense's 10.3 in government-profile barrel, stripped: cold hammer forged chrome moly vanadium steel (Primary Arms writes \"41V50\"; OperationParts, Botach and Alexander's \"4150\"), a chrome lined 5.56 NATO chamber and bore, 1:7 twist, a heavy phosphate finish, a carbine-length gas port on a .750 in journal, an A4 extension with M4 feed ramps, a 1/2-28 muzzle thread. Sold without a gas block or a muzzle device.","weight":"daniel-defense-103-barrel.weight","barrelLength":"daniel-defense-103-barrel.length","cartridge":{"takes":["5.56 NATO"],"stated":"Chambered in 5.56 NATO, 1:7 twist","source":"https://www.primaryarms.com/daniel-defense-5-56-10-3-17-chf-barrel-carbine-length-gas-system-07-077-16176-018 (Primary Arms' Features for the maker's number 07-077-16176-018, as cached: harvest.quote; its table has \"Caliber Gauge 5.56 NATO\", OperationParts' \"Caliber 5.56mm NATO\", Alexander's \"5.56 NATO\")"},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"extension":{"origin":[0,0,0],"note":"The barrel extension's flange, its rear face, on the bore axis, +x toward the muzzle."},"muzzle":{"origin":["{.shoulder_x}",0,0]},"gas_journal":{"origin":["{.gas_port_x}",0,0]}},"interfaces":{"barrel_extension":{"type":"ar15.barrel_extension","role":"barrel","anchor":"extension","params":{},"flips":false,"note":"Primary Arms: \"A4 barrel extension\" and \"Feed Ramps M4\"; OperationParts: \"Barrel Extension A4\"; Alexander's: \"A4 with extended M4 feed ramps\"."},"muzzle":{"type":"muzzle_thread","role":"barrel","anchor":"muzzle","params":{"thread":"1/2-28","thread_length":"={.thread_length}"},"flips":false,"note":"The thread is four sellers' statement for this number (Primary Arms \"Threaded 1/2x28\" and \"Thread Pattern 1/2 X 28\", OperationParts \"1 ⁄ 2 × 28 TPI (Threads Per Inch)\", Alexander's and AR15Discounts \"1/2×28\"), and the maker's own picture has its stripes 28.1 to the inch. Its length is read off that picture: 0.633 ± 0.015 in, the Army barrel's .63."},"gas_journal":{"type":"ar15.gas_journal","role":"barrel","anchor":"gas_journal","params":{"journal_od":"={.journal_od}"},"flips":false,"note":"Primary Arms: \"Gas Seat Diameter .750\"; OperationParts: \"Diameter At Gas Port .750″\". The journal runs from 6.94 to 8.80 in ahead of the receiver's face, the port 0.28 in ahead of its rear shoulder, which a gas block comes back to (the collar's front face). Right To Bear: \"Dimpled? No\"; Charlie's Custom Clones: \"No gas block, not drilled for gas block\"."},"gas_system":{"type":"ar15.gas_system","role":"barrel","params":{"length":"carbine"},"flips":false,"note":"Primary Arms, for this number: \"Carbine gas system\" and \"Gas System Length Carbine\"; OperationParts: \"Gas System Carbine Length\". The maker's own page is not read (its site refuses the reader). What the platform checks a gas tube against a barrel by (D83)."}},"materials":{"barrel":{"label":"Barrel","finish":"phosphate","recolorable":false,"color":"daniel-defense-phosphate","note":"Primary Arms: \"Manganese phosphate exterior finish\" and \"Barrel Coating Manganese Phosphate\"; OperationParts: \"Mil-spec heavy phosphate coated\" and \"Outside Finish Mil-Spec Heavy Phosphate\"; Alexander's: \"Finish: Mil-Spec Heavy Phosphate Exterior, Chrome Lined Bore and Chamber\" and \"Color: Black\". The one finish this number is sold in. A matte charcoal from the chamber section to the thread: #494946 over the whole barrel in the sellers' side view (0ec43808ddef), #50504d and #575755 on its thin section in their two three-quarter views (800edcb32507, 0105c617ad8c). Not drawn: the chrome of the bore and the chamber (inside), the marking stamped along the top of the thin section."},"extension":{"label":"Barrel extension","finish":"phosphate","recolorable":false,"color":"steel-phosphate-charcoal","note":"The barrel extension, its flange and its index pin: another piece of steel screwed onto the barrel, and a little darker than it in every one of the sellers' pictures (#403f3c beside the barrel's #494946 in the side view 0ec43808ddef, #474744 beside #50504d and #4a4947 beside #575755 in the two three-quarter views, #504f4d beside #626261 in the breech view 3e288080affe). No page names its finish apart from the barrel's (\"Mil-Spec Heavy Phosphate Exterior\"); the maker's own small picture (50c0d40d42c5) has it a warmer grey, #5e5550 beside #565253, which isn't followed (a retouched 1000 px picture against four of one series). The pin is the extension's own colour in the breech view. The two feed ramps, cut in this piece, are bright bare steel there: they are drawn in the extension's grey, a cut's faces being no piece of their own."}},"components":{},"geometry":{"model":"daniel-defense-103-barrel.glb","components":{},"approximations":["Turned from stations in the ledger, each read off a picture (no drawing or dimension of its profile is published): lengths on the maker's own square-on picture, at the scale the published 10.3 in less the Army's .620 tenon gives between the flange's front face and the muzzle; diameters on the sellers' larger picture, each against the .750 gas block journal. The two pictures agree on every diameter within 0.005 in, and the model is within a pixel and a half of the square-on one's traced outline.","The 10.3 in is taken from the barrel's breech face, as the catalog's other barrels' lengths are. Taken from the bolt's face the muzzle and every station would stand up to an eighth of an inch further back; the maker's picture, by its own thread's pitch and by its extension's diameter, is against that.","The barrel extension is the standard one, as the reference CAD set has a mil-spec M4 extension: its body at the Army's .999, its length and its flange that set's, and its rear end that set's too: eight locking lugs, one under the pin, the slots between them (0.124 in wide, flat-floored), the cone on the lugs' rear faces, the recess ahead of them, and the two M4 feed ramps (cylinders of .280 in leaning 45° to the bore, in the two slots either side of the bottom). This barrel's own breech view shows its lugs and its two ramps and measures none of them. Its flange's diameter is this barrel's own, 1.171. The barrel's own pictures read the extension 0.036 in longer behind the flange than the standard: not followed.","The section under the hand guard narrows toward the muzzle (0.688 to 0.612 in) as both pictures have it. The flare up to the collar is a curve tangent to that section and to a cone of 19° a side, fitted to the larger picture's silhouette. Every corner is drawn square (the pictures show edge breaks of a hundredth or two).","The muzzle thread is a helix, 28 to the inch, between the minor and major diameters of the Army barrel's 1/2-28 thread: a plain V without the flats of its form, right-hand (assumed: its designation marks no other), running out at the shoulder over its last pitch. The relief groove both pictures show between the shoulder and the first thread isn't cut, nor the break of the muzzle's rim.","The gas port is a hole of .070 in (a seller's title for this number; the picture's spot is 0.064 ± 0.008 across) on top of the journal, 0.283 in ahead of the collar, down to the bore. The indexing pin is the reference CAD set's .125, where and as high as the square-on picture has it. The bore is one plain hole right through, at the Army drawing's .219.","Not drawn: the chamber, the muzzle's crown, the chamfers on the lugs' front faces and the rounds on the extension's edges (a hundredth of an inch in the reference set), the marking stamped along the top of the thin section (\"DD\", a letter, \"MP 5.56 NATO 1/7\")."],"ledger":["daniel-defense-103-barrel.overall_length","daniel-defense-103-barrel.extension_rear_x","daniel-defense-103-barrel.flange_front_x","daniel-defense-103-barrel.shoulder_x","daniel-defense-103-barrel.thread_length","daniel-defense-103-barrel.gas_port_x","daniel-defense-103-barrel.journal_od","daniel-defense-103-barrel.muzzle_od"]},"profiles":{"side":{"plane":"xy","origin":"the extension's rear face, on the axis","offset":{"x":"extension_rear_x"},"points":[[0,0.417],[0.011,0.406],[0,0.395],[0.001,0.003],[0.002,-0.355],[0.013,-0.367],[0.013,-0.501],[0.03,-0.518],[0.053,-0.518],[0.064,-0.506],[0.075,-0.518],[0.444,-0.517],[0.456,-0.505],[1.038,-0.504],[1.043,-0.51],[1.044,-0.577],[1.06,-0.594],[1.184,-0.593],[1.194,-0.492],[1.206,-0.492],[1.217,-0.504],[1.833,-0.502],[1.844,-0.491],[1.922,-0.491],[1.933,-0.479],[1.978,-0.479],[1.989,-0.468],[2.045,-0.468],[2.056,-0.457],[2.112,-0.457],[2.124,-0.445],[2.18,-0.445],[2.191,-0.434],[2.247,-0.434],[2.258,-0.423],[2.314,-0.423],[2.325,-0.411],[2.381,-0.411],[2.392,-0.4],[2.437,-0.4],[2.448,-0.389],[2.504,-0.389],[2.515,-0.377],[2.571,-0.377],[2.582,-0.366],[2.638,-0.366],[2.65,-0.355],[2.717,-0.354],[2.728,-0.343],[4.094,-0.34],[4.105,-0.329],[5.46,-0.325],[5.471,-0.314],[7.038,-0.31],[7.049,-0.322],[7.116,-0.321],[7.128,-0.333],[7.172,-0.332],[7.184,-0.344],[7.217,-0.344],[7.228,-0.355],[7.251,-0.355],[7.262,-0.366],[7.296,-0.366],[7.307,-0.377],[7.329,-0.377],[7.363,-0.399],[7.385,-0.399],[7.441,-0.433],[8.091,-0.431],[8.107,-0.414],[8.113,-0.375],[9.098,-0.373],[9.109,-0.384],[9.188,-0.384],[9.994,-0.382],[10.005,-0.37],[10.24,-0.37],[10.251,-0.381],[10.341,-0.381],[10.369,-0.364],[10.369,-0.33],[10.38,-0.319],[10.38,-0.252],[10.408,-0.246],[10.43,-0.224],[10.452,-0.246],[10.475,-0.224],[10.486,-0.246],[10.497,-0.246],[10.508,-0.235],[10.52,-0.246],[10.531,-0.246],[10.542,-0.235],[10.553,-0.246],[10.564,-0.246],[10.576,-0.235],[10.587,-0.246],[10.598,-0.246],[10.609,-0.235],[10.62,-0.235],[10.632,-0.246],[10.643,-0.235],[10.654,-0.235],[10.665,-0.246],[10.676,-0.246],[10.688,-0.234],[10.699,-0.246],[10.71,-0.246],[10.721,-0.234],[10.732,-0.246],[10.744,-0.246],[10.755,-0.234],[10.766,-0.245],[10.777,-0.245],[10.788,-0.234],[10.822,-0.245],[10.833,-0.234],[10.844,-0.245],[10.855,-0.234],[10.867,-0.234],[10.878,-0.245],[10.889,-0.245],[10.9,-0.234],[10.911,-0.245],[10.923,-0.245],[10.934,-0.234],[10.945,-0.245],[10.967,-0.245],[10.973,-0.228],[10.995,-0.206],[10.995,-0.15],[11.006,-0.139],[11.006,0.108],[10.995,0.119],[10.995,0.13],[11.006,0.141],[10.995,0.153],[10.994,0.209],[10.966,0.236],[10.955,0.225],[10.944,0.248],[10.933,0.248],[10.922,0.225],[10.899,0.247],[10.888,0.225],[10.866,0.247],[10.854,0.236],[10.843,0.236],[10.832,0.247],[10.821,0.236],[10.81,0.236],[10.798,0.247],[10.776,0.225],[10.765,0.236],[10.754,0.236],[10.742,0.225],[10.72,0.247],[10.709,0.225],[10.698,0.225],[10.686,0.247],[10.681,0.23],[10.664,0.225],[10.653,0.247],[10.63,0.224],[10.619,0.247],[10.608,0.247],[10.597,0.224],[10.574,0.247],[10.563,0.224],[10.541,0.247],[10.535,0.23],[10.519,0.224],[10.507,0.247],[10.485,0.224],[10.474,0.246],[10.451,0.224],[10.44,0.246],[10.418,0.224],[10.407,0.246],[10.395,0.235],[10.379,0.241],[10.378,0.319],[10.367,0.33],[10.361,0.369],[10.003,0.368],[9.992,0.38],[8.111,0.375],[8.105,0.414],[8.089,0.431],[7.439,0.429],[7.383,0.396],[7.361,0.396],[7.327,0.373],[7.305,0.373],[7.294,0.362],[7.26,0.362],[7.249,0.351],[7.227,0.351],[7.216,0.339],[7.182,0.339],[7.171,0.328],[7.115,0.328],[7.104,0.317],[7.037,0.317],[7.025,0.305],[6.578,0.304],[6.566,0.315],[5.402,0.313],[5.391,0.324],[4.63,0.322],[4.618,0.333],[3.678,0.331],[3.667,0.342],[2.704,0.34],[2.693,0.351],[2.659,0.351],[2.648,0.362],[2.581,0.362],[2.569,0.373],[2.536,0.373],[2.525,0.384],[2.469,0.384],[2.457,0.395],[2.401,0.395],[2.39,0.406],[2.345,0.406],[2.334,0.417],[2.278,0.417],[2.267,0.428],[2.211,0.428],[2.2,0.439],[2.144,0.439],[2.133,0.45],[2.088,0.45],[2.077,0.461],[2.032,0.461],[2.021,0.472],[1.965,0.472],[1.953,0.483],[1.897,0.483],[1.886,0.494],[1.349,0.493],[1.338,0.504],[1.192,0.504],[1.186,0.51],[1.186,0.566],[1.198,0.577],[1.181,0.594],[1.058,0.593],[1.052,0.588],[1.052,0.52],[1.035,0.504],[1.024,0.515],[0.901,0.514],[0.89,0.503],[0.532,0.502],[0.52,0.502],[0.509,0.514],[0.028,0.512],[0.011,0.496],[0.011,0.428]],"scaleRefs":["daniel-defense-103-barrel.flange_od"],"inputs":{"daniel-defense-103-barrel.flange_od":1.187},"tolerance":0.005,"photo":"references/daniel-defense-103-barrel 50c0d40d42c5 (Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, on white, 1000 x 1000)","method":"luminance < 200, 1 boxes excluded, largest piece, holes filled; rotated +0.1° as declared; scale from daniel-defense-103-barrel.flange_od = 1.187 in (y-extent 106 px → 89.3 px/in); origin at x min, y center of the outline; Douglas-Peucker at 0.005 in with the extremes kept: 262 points (IoU 0.998 with the full outline); The index pin (columns 88 to 100 of the upper edge) is boxed out: it is a pin, not a ring. The maker's mark at the picture's lower right is another piece and is dropped.; checks: centre between the top (max over 0.4 in windows) along x [2.9, 6.9] -0.002 ± 0.034; centre between the top (max over 0.4 in windows) along x [8.2, 9.8] 0.002 ± 0.034; height (tooth tops, max over 0.05 in windows) along x [8.2, 9.8] 0.752 ± 0.034 in vs daniel-defense-103-barrel.journal_od 0.75 ± 0.0005 (corroborated): agrees; height (tooth tops, max over 0.05 in windows) along x [0.15, 0.85] 1.018 ± 0.034 in vs daniel-defense-103-barrel.extension_od_photo 1.013 ± 0.008 (corroborated): agrees; height (tooth tops, max over 0.05 in windows) along x [1.35, 1.75] 0.996 ± 0.034 in vs daniel-defense-103-barrel.chamber_od 0.993 ± 0.004 (corroborated): agrees; height (tooth tops, max over 0.05 in windows) along x [7.5, 7.95] 0.862 ± 0.034 in vs daniel-defense-103-barrel.collar_od 0.85 ± 0.004 (corroborated): agrees; height (tooth tops, max over 0.05 in windows) along x [10.05, 10.2] 0.739 ± 0.034 in vs daniel-defense-103-barrel.muzzle_od 0.74 ± 0.005 (corroborated): agrees; width 11.006 ± 0.081 (tools/trace.py)","via":"harvest","note":"Dark grey on white, square on to the barrel: the outline is the silhouette at grey 200, and each step of it is the face itself. Its diameters are at the scale its .750 journal gives (a dark tube reads thin on white, which a diameter's scale takes out); its lengths read 2% long at that scale, and the model sets the barrel's own length, the flange's front face to the muzzle, to the published one."}},"gaps":[{"what":"Where the 10.3 in is measured from","need":"The maker's statement (its site refuses the reader), or a drawing: from the barrel's breech face, as taken, or from the closed bolt's face, an eighth further back. The maker's square-on picture is for the breech face by its thread's pitch (10.90 in end to end at 28 to the inch, against 10.801 and 10.675) and by its extension's diameter (10.80), though that second ruler reads 10.66 with the edges taken at their palest"},{"what":"Its profile's diameters","need":"The maker's drawing or table: none is published. Each is a picture's reading against the .750 journal, ± 0.004 to 0.008 in"},{"what":"The barrel extension's length","need":"This barrel's two pictures read it 1.00 to 1.03 in behind the flange's rear face where the reference CAD set's standard extension has 0.990: a drawing of the extension (8448550 isn't in the package), or a picture with a scale on it"},{"what":"The gas port's diameter and place","need":"The maker's figures. A seller's title says .070 and a customer's review that the maker has shipped .070 and .082; its place is read off one picture turned 19° to the lens (± 0.03 in): 0.06 to 0.10 in ahead of where the catalog's mid-length barrels' ports and Aero's two tube lengths would put it, which a 10.3 measured from the bolt's face would take up"},{"what":"The relief groove at the shoulder, the muzzle's crown and the edge breaks","need":"Close views square to the muzzle end with a scale in their plane: the sellers' pictures show them from 16 in and 20° off"},{"what":"The extension's locking lugs and feed ramps, and the chamber's mouth","need":"The extension's drawing (8448550 isn't in the package): its lugs, slots and ramps are the reference CAD set's, a third-party model of a mil-spec part; hidden once the barrel is in a receiver"}]},"daniel-defense-bcg":{"id":"daniel-defense-bcg","name":"Complete Bolt Carrier Group","manufacturer":"Daniel Defense","sku":"04-013-19032","category":"bolt_carrier_group","description":"Daniel Defense's complete M16-profile bolt carrier group, as its sellers list it: an 8620 carrier and a Carpenter 158 bolt, heavy (manganese) phosphate outside, the carrier's bore and gas key chrome lined, the key staked, the bolt shot peened with an extractor booster; \"the exact same BCG that goes into almost every Daniel Defense rifle and complete upper\" (Primary Arms).","weight":"daniel-defense-bcg.weight","cartridge":{"takes":["5.56 NATO",".223 Rem",".300 Blackout"],"stated":"Daniel Defense 5.56 NATO (5.56x45mm & .223 Remington) / 300 Blackout (7.6x35mm) full-auto compatible, M16 Profile, complete bolt carrier group assembly.","source":"Sellers' words (Daniel Defense's site refuses the reader): the sentence is Rifle Supply's description, https://riflesupply.com/daniel-defense-complete-bolt-carrier-group-5-56mm-matte-finish-black/, and Scheels' for the same number, https://www.scheels.com/p/daniel-defense-complete-bolt-carrier-group/815604-04-013-19032/ (two shops, one sentence: the maker's own, as they carry it); Wing Tactical: \"Caliber: 5.56 NATO / .223 Rem. / 300BLK\"; Primary Arms: \"Chambered in 5.56 NATO\"; MidwayUSA: \"Cartridge 223 Remington\", \"5.56x45mm NATO\". As cached: harvest.quote."},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"channel":{"origin":[0,0,0],"note":"The receiver's rear face on the bore axis, +x toward the muzzle: the carrier's rear face stands here in battery."}},"interfaces":{"carrier_channel":{"type":"ar15.carrier_channel","role":"carrier","anchor":"channel","params":{},"flips":false}},"materials":{"body":{"label":"Carrier group","finish":"phosphate","recolorable":false,"color":"steel-phosphate-charcoal","sheen":"satin","note":"Primary Arms: \"Heavy phosphate coating, chrome-lined carrier bore and gas key\", its table \"Carrier Finish Manganese Phosphate\" and \"Bolt Finish Manganese Phosphate\"; Wing Tactical: \"Finish: Heavy Phosphate Coated\"; MidwayUSA: \"Color Black Phosphate\". The one finish it is sold in: no page found offers another (a shop's title with \"black nitride\" was seen in a search only, not opened). The carrier, the key, the cam pin and the bolt are one slot: one phosphate in all the photos (Primary Arms' four, Wing's seven, MidwayUSA's). Its tone (tools/color_sample.py, the whole group): #43423f in Primary Arms' side view (255576c2e711), #4c4845 in MidwayUSA's retouched one (471e7ee54656), #4e4d4a in Rifle Supply's (470a5b81f6b0), #5a5a5a in Wing's (1aa60cad3276); nine levels lighter than BCM's carrier in the same seller's series (#3a3a38, steel-phosphate-dark), and where steel-phosphate-charcoal draws a carrier. Under it, in the app's hero direction (make color-match, .cache/color-match/dd-bcg in the batch's worktree: build bcm-16-mid with this group, exploded, light backdrop) it renders #474746 on the tail's lit flat and #474745 on the front half, for Primary Arms' #444341 and #43423f there: 3 to 6 levels a channel, the photo a little warmer, within what one carrier's photos differ by. So the existing preset, and no new one. Satin, as BCM's: oiled in its photos. Not drawn: the chrome inside the key's mouth and the carrier, Daniel Defense's logo lasered light grey on the right side ahead of the vents, the \"P\" stamped on the bolt, the extractor."},"screws":{"label":"Key screws","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The key's two socket screws: a blacker, glossier black than the phosphated key in Primary Arms' view from above (ff833cef1e53), where the key's staking shows as a nick into each head from both sides. No page names their finish: a black, not matched to a photo (two heads a quarter inch across)."}},"components":{},"geometry":{"model":"daniel-defense-bcg.glb","components":{},"approximations":["Its shape is the Army's drawings', not Daniel Defense's own (no drawing or dimension of Daniel Defense's is on any page): its sellers call it \"a mil-spec, full-auto compatible, M16 profile bolt carrier group assembly\" (Primary Arms) with \"Mil-Spec dimensions\" (Wing Tactical), so it is drawn as the M16 carrier (8448507), its key (8448506) and screws (8448508), the cam pin (8448502) and the bolt (8448510) at those drawings' nominal sizes, as BCM's, Toolcraft's and Aero's are. Its photos were read only to check that: the forward assist's serrations counted (28, both side views, as the drawing's) and its tail's diameter read through their pitch (0.906 and 0.916 for the drawing's .930: a dark tube on white reads thin), and the two holes in its right side (the retaining pin's, through from the left, and the one below it) 5.1 and 2.0 of their pitches behind the last one's steep face in Primary Arms' side view, where the model has them 5.0 and 1.96 behind.","Drawn as the Army's assembly drawing (8448501) has it, out of the rifle: the bolt forward in the carrier (unlocked) and the cam pin upright. In battery the bolt is turned 22 1/2° and stands .255 to .325 in further back in the carrier (MidwayUSA's side view shows it so, 0.48 in out); the carrier's rear face is put at the receiver's rear face.","Daniel Defense's own, off its photos: the key's staking (\"Properly staked gas key\", Primary Arms), a notch down the key's upper side wall at each screw, both sides, 0.076 in wide and 0.048 deep from the top (Primary Arms' side view, scaled by the serrations' pitch; its view from above has the counterbore's rim pushed in over 0.09 at each), cut through the wall into the counterbore as the side view shows it, with the screw's head lit through it. Its sides are drawn straight and square to the key, as they look from the side; the metal a stake pushes into the head isn't drawn.","Not drawn: the bores inside the carrier ahead of the slot and the bolt behind the carrier's front face, the extractor (its claw stands in as an eighth lug), its spring and booster, and the ejector, the firing pin and its retaining pin, the gas rings, the key's 22°30' relief, the metal the staking pushes into each screw's head, Daniel Defense's logo (lasered, not in relief) and the bolt's \"P\", fillets and edge breaks beyond the two cut corners and a small bevel.","Assumed where the drawing wasn't resolved, as the other three carriers' parts say: each lower rail's lower flank is the plane through the axis that touches the groove beside it; the groove's centre is where it touches the rib's side on the 45° ray; the cam track's helix is straight between the table's 0° and 20° rows; the 1.500 R is the run-out of the two grooves to the rear; the notch under the tail runs the tail's length; the serrations' steep faces are toward the front, as Daniel Defense's photos show them; the screws' heads are flush with the key's top; the vents, the hole in the right side and the cam track are drawn in as far as the bolt's diameter."],"ledger":["daniel-defense-bcg.length","daniel-defense-bcg.od","daniel-defense-bcg.serration_count","daniel-defense-bcg.tail_od","daniel-defense-bcg.stake_width","daniel-defense-bcg.stake_depth"]},"profiles":{},"gaps":[{"what":"Anything from Daniel Defense itself","need":"Its site refuses the reader (PLAN D59): every figure is a seller's. A page the user saves from their own browser, or the maker's words hosted elsewhere, would give its own"},{"what":"A weight that was weighed","need":"Wing's 11.5 oz and Primary Arms' 11 oz are sellers' rows half an ounce apart, and the review repeats the round one; a scale reading of this group (a review's table) would settle it"},{"what":"Anything of Daniel Defense's own shape","need":"No drawing or size is published; the model is the Army's carrier, checked against the photos by the serrations' count, the tail's diameter and the two side holes' places only. The lasered logo isn't drawn; the staking is drawn as a straight-sided notch through the key's wall, as the side view shows it, without the metal it pushes into the head"}]},"daniel-defense-fixed-front-sight":{"id":"daniel-defense-fixed-front-sight","name":"Rail Mounted Fixed Front Sight","manufacturer":"Daniel Defense","sku":"19-017-04013","url":"https://www.primaryarms.com/daniel-defense-rail-mount-fixed-front-sight-19-017-04013","category":"backup_sight","description":"Daniel Defense's rail-mounted fixed front sight (Rock & Lock): one piece of 6061-T6 aluminium, hard anodized, for a Picatinny rail by one slotted screw into a self-locking stainless insert; a standard AR-15 front sight post, a glare-reducing serrated rear ramp, concave sides to rest a thumb on a compact light ahead of it. Black; Mil-Spec+ Brown and Tornado Grey in the set with the A1.5 rear.","weight":"daniel-defense-fixed-front-sight.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":["{.length} / 2 - {.screw_behind_front}",0,0],"note":"On the rail's top at the clamp screw's axis: the screw crosses the channel in a rail slot, so it is what a slot holds. It lies at the middle of the base."},"optical_axis":{"origin":["{.length} / 2 - {.post_behind_front}","{.sight_line_above_rail}",0],"note":"The post's tip (Wing's 1.36 over the rail), on the sight's middle plane, 0.33 in behind the front face (the patent's top view)."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":"={.length} - {.screw_behind_front}","clamp_front":"={.screw_behind_front}"},"flips":false,"start":"front","note":"The base's two ends about the clamp screw (0.50 in each way). Daniel Defense (Sportsman's): \"The one piece design makes it easy to install on any MIL-STD-1913 rail and it secures with a slotted fastener threaded into a self-locking stainless steel thread insert. Special attention was paid to facilitate the use of compact weapon-lights forward of the sight, such as the X300, TLR-1, etc.\" Primary Arms: \"a lightweight, streamlined fixed sight built to mount behind compact weapon lights like the Streamlight TLR-1 or SureFire X300 without blocking light activation\". Wing Tactical, of the set: \"**Sight is designed to work on same plane rail systems only. Will not work with a railed gas block that is higher or lower than the receiver.\""},"sight_line":{"type":"optic.sight_line","role":"irons","params":{"magnification":"1x"},"flips":false,"note":"An iron sight: it doesn't magnify, and nothing is checked against it (data/interfaces.yaml). \"Uses standard AR-15 front sight posts\" (Primary Arms): the post screws up and down to zero it."}},"materials":{"body":{"label":"Sight","finish":"anodized","recolorable":true,"color":"placeholder-black","sheen":"matte","options":{"black":{"label":"Black","finish":"anodized","color":"placeholder-black","sheen":"matte","sku":"19-017-04013","source":"https://www.primaryarms.com/daniel-defense-rail-mount-fixed-front-sight-19-017-04013"},"tornado":{"label":"Tornado Grey","finish":"anodized","color":"daniel-defense-tornado-grey","sheen":"matte","sku":"19-088-09116-012","source":"https://gritroutdoors.com/daniel-defense-fixed-front-rear-sights-19-088-09116-012"}},"default":"black","note":"Primary Arms: \"MIL-SPEC hardcoat anodized black finish\"; Daniel Defense (Right to Bear): \"Machined from 6061-T6 aluminum and military specification Type III Hard Coat Anodized\". The sight alone is sold in black only (19-017-04013, every page on file). Daniel Defense also sells the pair, and only the pair, as Mil-Spec+ Brown (19-088-09116-011) and Tornado Grey (19-088-09116-012): its 2026 price list has both, and no front or rear alone in a colour. Tornado Grey is offered since 2026-11-02 (the user: \"make sure we find an active listing for each part in gray before we add it\"): GRITR Outdoors' page for 19-088-09116-012 sold it that day (\"Tornado Gray\", in stock, $173.00, its markup's MPN 19-088-09116-012), and its price is the set's (daniel-defense-fixed-sight-set): a sight in this colour alone has none. Its colour is matched on Evike's own two photographs of the set (references/daniel-defense-fixed-front-sight 068da96fe436 and 393b7739d245, as EMG Arms serves them): a light, cool grey body with the post, the screws, the aperture and the drum black, which no tint of the black set's picture gives, and the rear marked \"U.S. PAT. 8,407,923\" where Daniel Defense's black studio picture reads D631,935. Daniel Defense's sell sheet: \"Type III Hard Coat Anodized (Tornado Gray)\". GRITR's own six pictures for the grey set are the black sights (Daniel Defense's studio pictures, two with the rifle behind lightened): not used. Mil-Spec+ Brown stays not offered. Reviewed again 2026-10-28: GRITR Outdoors brown set 5ae12c63efa9 and GRITR Sports gray set fc8d89741103 register as the same underlying photograph (ECC 0.99901; body-region color-transform residual 2.6 to 3.4 levels of 255). Those files cannot establish which finish was photographed. The individual brown views are crops of that same image. Two owner photos linked by Imgur albums TRQ2pEZ and nw0nId9 corroborate brown bodies and black hardware but have strong blue illumination and pink paper reflected in the anodize, so they are not used to fit a factory swatch. A black on sealed anodize is its finish type's look, not fitted."},"hardware":{"label":"Post and screw","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The A2 post and the clamp screw: black steel on the black and on the brown sight alike (GRITR Outdoors' brown set, 5ae12c63efa9). The Army's drawing 9349056 has the post of steel bar with a protective finish; the screw's isn't stated. A black on steel isn't fitted."},"insert":{"label":"Thread insert's rim","finish":"anodized","recolorable":false,"color":"daniel-defense-insert-red","follows":{"slot":"body","options":{"tornado":{"finish":"stainless","color":"stainless-natural"}}},"note":"The self-locking stainless insert's end on the left side, under the screw (Sportsman's: \"self-locking stainless steel thread insert\"): a red ring in Primary Arms' photos of the black sight (3e7ddce836d9, 129cb83973fd), the same red as the rear sight's. On the Tornado Grey set the insert's end shows bare steel, no red (Evike's photo of the set from its insert side, 393b7739d245): drawn as bright stainless there."}},"components":{},"geometry":{"model":"daniel-defense-fixed-front-sight.glb","components":{},"approximations":["Built from Daniel Defense's design patent (US D631,934 S): the screw-side elevation (FIG. 5) at the published length's scale (Wing: a whole inch), the rear view (FIG. 4) at the overall height that gives, and the bottom view (FIG. 8) at the length's scale, intersected. The scale is borne out by the post: the rear view's blade is the Army drawing's .070 within a thousandth.","The post is the Army's drawing 9349056: its square blade (.070), the four fillets to its round root and the notched flange (.366 across), standing with its tip at Wing's 1.36 in over the rail (the patent draws it at 1.330: it screws up and down). The detent beside it and the thread under the flange aren't drawn.","The serrated rear ramp is drawn smooth: its serrations haven't been counted on a photo yet. The lettering on the front face (\"<- UP\", the DD logo, the patent number) isn't drawn.","The channel is the rail's head (MIL-STD-1913, lib.rail_seat) from end to end; below the head's lower gauge line the feet's own inner faces (FIG. 4) are kept. The two slits run the base's length. The clamp screw is a plain rod across the channel at its read place and an assumed 0.19 in shank (no page names it), its head a slotted disc beyond the right foot, the insert a ring on the left.","Edges are broken by a small bevel."],"ledger":["daniel-defense-fixed-front-sight.length","daniel-defense-fixed-front-sight.width","daniel-defense-fixed-front-sight.height","daniel-defense-fixed-front-sight.height_drawn","daniel-defense-fixed-front-sight.sight_line_above_rail","daniel-defense-fixed-front-sight.clamp_below_rail","daniel-defense-fixed-front-sight.screw_behind_front"]},"profiles":{"side":{"plane":"xy","origin":"the base's front face at the jaws' feet; offset to the clamp's middle on the rail's top","offset":{"x":"front_x","y":"clamp_bottom_y"},"points":[[-1,0.247],[-1,0.007],[-0.995,0],[-0.005,0],[0,0.003],[0,1.42],[-0.003,1.453],[-0.026,1.524],[-0.058,1.57],[-0.116,1.622],[-0.166,1.645],[-0.23,1.66],[-0.335,1.66],[-0.41,1.642],[-0.457,1.616],[-0.515,1.562],[-0.55,1.503],[-0.61,1.265],[-0.705,0.973],[-0.81,0.715],[-0.854,0.632],[-0.853,0.623],[-0.893,0.54],[-0.959,0.423],[-0.984,0.355]],"features":{"screw_head":[[[-0.687,0.399],[-0.31,0.399],[-0.31,0.023],[-0.687,0.023]]],"base_top":[[[-0.95,0.44],[-0.002,0.44],[-0.002,0.44],[-0.95,0.44]]]},"scaleRefs":["daniel-defense-fixed-front-sight.length"],"inputs":{"daniel-defense-fixed-front-sight.length":1},"tolerance":0.004,"photo":"references/daniel-defense-fixed-front-sight c59fd8c41e1d (US D631,934 S (Daniel Defense, 'Front firearm sight'), FIG. 5, the screw side, the muzzle to the viewer's right (the sight's right); the patent office's copy, page 6, 300 dpi)","method":"luminance < 128, inside [600, 580, 1960, 2790], closing ×3, largest piece, holes filled, inset 2 px (half the outline's stroke); scale from daniel-defense-fixed-front-sight.length = 1 in (x-extent 1300 px → 1300.0 px/in); origin at x max, y min of the outline; Douglas-Peucker at 0.004 in with the extremes kept: 25 points (IoU 0.998 with the full outline); features through the same placement (screw_head: the clamp screw's slotted head (outer circle: columns 1038 and 1529 along row 2485, rows 2241.5 and 2730 down column 1300); base_top: the base's top edge across the side (row 2188)) (tools/trace.py)","via":"harvest","note":"The sight's right side: the round crown over the ears, the flat front face, the ramp sloping back to the base, the clamp screw's head low in the middle."},"rear":{"plane":"zy","origin":"midway between the feet (the ears' and the post's middle); the feet, offset to the rail's top","offset":{"y":"clamp_bottom_y"},"points":[[-0.616,0.308],[-0.616,0.098],[-0.575,0.036],[-0.548,0.011],[-0.527,0],[-0.448,0],[-0.447,0.235],[0.445,0.235],[0.445,0],[0.523,0],[0.54,0.006],[0.572,0.036],[0.616,0.098],[0.616,0.308],[0.605,0.344],[0.557,0.392],[0.487,0.444],[0.429,0.468],[0.327,0.535],[0.273,0.554],[0.274,1.357],[0.307,1.538],[0.354,1.66],[0.263,1.66],[0.224,1.538],[0.176,1.353],[0.13,1.315],[-0.011,1.308],[-0.134,1.315],[-0.182,1.355],[-0.225,1.538],[-0.265,1.66],[-0.355,1.66],[-0.31,1.538],[-0.276,1.357],[-0.276,0.554],[-0.327,0.536],[-0.398,0.467],[-0.526,0.431],[-0.574,0.398],[-0.605,0.351]],"features":{"post":[[[-0.036,1.565],[0.034,1.565],[0.034,1.308],[-0.036,1.308]]],"slits":[[[-0.212,0.736],[-0.152,0.736],[-0.152,0.236],[-0.212,0.236]],[[0.149,0.736],[0.211,0.736],[0.211,0.236],[0.149,0.236]]],"ceiling":[[[-0.298,0.236],[0.294,0.236],[0.294,0.236],[-0.298,0.236]]],"tower":[[[-0.275,1.355],[0.272,1.355],[0.272,0.553],[-0.275,0.553]]],"screw_head":[[[0.616,0.371],[0.648,0.371],[0.648,0.043],[0.616,0.043]]]},"scaleRefs":["daniel-defense-fixed-front-sight.height_drawn"],"inputs":{"daniel-defense-fixed-front-sight.height_drawn":1.66},"tolerance":0.004,"photo":"references/daniel-defense-fixed-front-sight 16d7ad5940f5 (US D631,934 S, FIG. 4, the rear view from the breech (the screw head at the viewer's right: the sight's right is +z); page 5, 300 dpi)","method":"manual polygon (46 points picked on the photo); scale from daniel-defense-fixed-front-sight.height_drawn = 1.66 in (y-extent 1822 px → 1097.6 px/in); origin at x center, y min of the outline; Douglas-Peucker at 0.004 in with the extremes kept: 41 points (IoU 0.997 with the full outline); features through the same placement (post: the post's blade between the ears: its sides (u 1187.5, 1264 on row 800), its tip (v 769.5 down column 1222); slits: the base's two slits, from the channel's ceiling up to their round tops (v 1680): walls u 994 and 1060, 1391 and 1459; ceiling: the channel's ceiling: the rail's top (v 2229, columns 1100, 1222 and 1300); tower: the tower's faces under the ears (u 925, 1526), down to where they flare (v 1880); screw_head: the clamp screw's head beyond the right foot (to u 1938)) (tools/trace.py)","via":"harvest","note":"The whole sight from behind, the post left out: the ears flaring at their tops, the narrow tower, the concave flares down to the base (\"the concave radius on either side of the sight\"), the feet."},"plan":{"plane":"xz","origin":"the base's front face, midway across; offset to the clamp's middle","offset":{"x":"front_x"},"points":[[-1,0.452],[-1,-0.454],[-0.729,-0.623],[-0.273,-0.623],[0,-0.452],[0,0],[0,0.45],[-0.262,0.623],[-0.729,0.623]],"scaleRefs":["daniel-defense-fixed-front-sight.length"],"inputs":{"daniel-defense-fixed-front-sight.length":1},"tolerance":0.004,"photo":"references/daniel-defense-fixed-front-sight 52bf49514708 (US D631,934 S, FIG. 8, the bottom view (the muzzle to the viewer's right, the screw head at the sheet's top: +z up); page 9, 300 dpi)","method":"manual polygon (8 points picked on the photo); scale from daniel-defense-fixed-front-sight.length = 1 in (x-extent 1387 px → 1387.0 px/in); origin at x max, y center of the outline; Douglas-Peucker at 0.004 in with the extremes kept: 9 points (IoU 0.998 with the full outline) (tools/trace.py)","via":"harvest","note":"From below: the base's outline, its four corners chamfered."}},"gaps":[{"what":"The length is a whole inch from one seller (Wing); the width and the height have no published figure on file (Modern Warriors' text, the discovery's lead, wasn't served to the harvester: 202, an empty body)","need":"A seller's table with the front sight's sizes in decimals, or the maker's"},{"what":"The serrations on the rear ramp: how many and how deep","need":"A count on Primary Arms' photo from behind (f0aba6d31478) or Wing's 55323"},{"what":"Mil-Spec+ Brown and Tornado Grey are sold only in the set and aren't offered: no colour matched","need":"make color-match on GRITR Outdoors' brown photos; a photograph (not a render) of the Tornado Grey set"},{"what":"danieldefense.com refuses the reader (D59): no maker's page, drawing or manual","need":"Pages of Daniel Defense's the user saves from their own browser"}]},"daniel-defense-fixed-rear-sight":{"id":"daniel-defense-fixed-rear-sight","name":"A1.5 Fixed Rear Sight","manufacturer":"Daniel Defense","sku":"19-064-11002","url":"https://www.primaryarms.com/daniel-defense-a1-5-fixed-rear-sight-19-064-11002","category":"backup_sight","description":"Daniel Defense's A1.5 fixed rear sight (Rock & Lock): one piece of 6061-T6 aluminium, hard anodized, on a Picatinny rail by one slotted screw into a self-locking insert; the standard A2 flip aperture (0.070 and 0.200 in) with an A1 windage wheel turned by a bullet's tip. Black; Mil-Spec+ Brown and Tornado Grey in the set with the front sight.","weight":"daniel-defense-fixed-rear-sight.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":["{.length} / 2 - {.screw_behind_front}",0,0],"note":"On the rail's top at the clamp screw's axis: the screw crosses the channel in a rail slot, so it is what a slot holds. The frame's origin is the middle of the base, 0.40 in behind it."},"optical_axis":{"origin":["{.length} / 2 - {.drum_behind_front}","{.sight_line_above_rail}",0],"note":"The aperture's centre, standing: on the windage screw that carries it (the drum's axis along the rail), at the height the patent draws it (1.363 over the rail; the front sight's patent has its post's tip at 1.330, Wing 1.36)."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":"={.length} - {.screw_behind_front}","clamp_front":"={.screw_behind_front}"},"flips":false,"start":"rear","note":"The base's two ends about the clamp screw (0.29 in ahead of it, 1.09 behind). Daniel Defense (Right to Bear): \"The one piece design makes it easy to install to any Military Specification flattop upper receiver and the sight is secured to the upper using a slotted fastener which is threaded into a self-locking steel thread insert\"; \"Its well thought out design does not impede the use of the charging handle on M4 type rifles\". Wing Tactical, of the set: \"**Sight is designed to work on same plane rail systems only. Will not work with a railed gas block that is higher or lower than the receiver.\""},"sight_line":{"type":"optic.sight_line","role":"irons","params":{"magnification":"1x"},"flips":false,"note":"An iron sight: it doesn't magnify, and nothing is checked against it (data/interfaces.yaml). Midway (Daniel Defense's text): \"The fixed rear sight is of the correct height for proper alignment with an A2 Rifle or M4 \"F\" Marked Front Sight Base, as well as for co-witnessing with a red dot optic.\""}},"materials":{"body":{"label":"Sight","finish":"anodized","recolorable":true,"color":"placeholder-black","sheen":"matte","options":{"black":{"label":"Black","finish":"anodized","color":"placeholder-black","sheen":"matte","sku":"19-064-11002","source":"https://www.primaryarms.com/daniel-defense-a1-5-fixed-rear-sight-19-064-11002"},"tornado":{"label":"Tornado Grey","finish":"anodized","color":"daniel-defense-tornado-grey","sheen":"matte","sku":"19-088-09116-012","source":"https://gritroutdoors.com/daniel-defense-fixed-front-rear-sights-19-088-09116-012"}},"default":"black","note":"Primary Arms: \"MIL-SPEC hardcoat anodized black finish\"; Midway: \"Type III Hard Coat Anodized\", \"Color Matte Black\". The sight alone is sold in black only (19-064-11002, every page on file). Daniel Defense also sells the pair, and only the pair, as Mil-Spec+ Brown (19-088-09116-011) and Tornado Grey (19-088-09116-012): its 2026 price list has both, and no front or rear alone in a colour. Tornado Grey is offered since 2026-11-02 (the user: \"make sure we find an active listing for each part in gray before we add it\"): GRITR Outdoors' page for 19-088-09116-012 sold it that day (\"Tornado Gray\", in stock, $173.00, its markup's MPN 19-088-09116-012), and its price is the set's (daniel-defense-fixed-sight-set): a sight in this colour alone has none. Its colour is matched on Evike's own two photographs of the set (references/daniel-defense-fixed-front-sight 068da96fe436 and 393b7739d245, as EMG Arms serves them): a light, cool grey body with the post, the screws, the aperture and the drum black, which no tint of the black set's picture gives, and the rear marked \"U.S. PAT. 8,407,923\" where Daniel Defense's black studio picture reads D631,935. Daniel Defense's sell sheet: \"Type III Hard Coat Anodized (Tornado Gray)\". GRITR's own six pictures for the grey set are the black sights (Daniel Defense's studio pictures, two with the rifle behind lightened): not used. Mil-Spec+ Brown stays not offered. Reviewed again 2026-10-28: GRITR Outdoors brown set 5ae12c63efa9 and GRITR Sports gray set fc8d89741103 register as the same underlying photograph (ECC 0.99901; body-region color-transform residual 2.6 to 3.4 levels of 255). Those files cannot establish which finish was photographed. The individual brown views are crops of that same image. Two owner photos linked by Imgur albums TRQ2pEZ and nw0nId9 corroborate brown bodies and black hardware but have strong blue illumination and pink paper reflected in the anodize, so they are not used to fit a factory swatch. A black on sealed anodize is its finish type's look, not fitted."},"hardware":{"label":"Drum, aperture and screws","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The windage drum and its hub, the A2 aperture, the clamp screw and the windage screw's slotted end: black steel in every photo, on the black and on the brown sight alike (GRITR Outdoors' brown set, 5ae12c63efa9, f1fb888cfd05). What they are made of and coated with isn't stated; a black on steel isn't fitted."},"insert":{"label":"Thread insert's rim","finish":"anodized","recolorable":false,"color":"daniel-defense-insert-red","follows":{"slot":"body","options":{"tornado":{"finish":"stainless","color":"stainless-natural"}}},"note":"The self-locking insert's end on the left side, under the clamp screw (Right to Bear: \"threaded into a self-locking steel thread insert\"; Sportsman's, of the front: \"self-locking stainless steel thread insert\"): a red ring in Primary Arms' photos of the black sight (86d9f645ef0f, 22739368dfff). On the Tornado Grey set the insert's end shows bare steel, no red (Evike's photo of the set from its insert side, 393b7739d245): drawn as bright stainless there."}},"components":{},"geometry":{"model":"daniel-defense-fixed-rear-sight.glb","components":{},"approximations":["Built from Daniel Defense's design patent (US D631,935 S): the body is the drum-side elevation (FIG. 5) at the published length's scale, its rear view (FIG. 4) at the overall height that gives, and its bottom view (FIG. 8) at the length's scale, intersected. At that scale the body is 1.81 in tall (TLO: 1.78) and its feet 1.255 in across (TLO: 1.24).","The aperture is drawn where the patent draws it (its centre 1.363 in over the rail; Wing's end-on photo reads 1.41, kept in the ledger as a conflict). It is the standard A2 aperture as two legs at a right angle on the windage screw, the large (0.200 in) standing and the small (0.070 in) lying forward, their thickness along the rail and the lying leg's reach assumed from the top view's proportions (ledger aperture_leg_thick).","The window, the split and the U between the walls are cut straight through from end to end, as the end views and the photos show them; the side faces' shallow steps under the drum (the patent's lines across FIG. 5) are not drawn: their depth is in no view.","The channel is the rail's head (MIL-STD-1913, lib.rail_seat) from the base's front face to its rear end; below the head's lower gauge line the feet's own inner faces (FIG. 4) are kept. The clamp screw is a plain rod across the channel at its read place and an assumed 0.19 in shank (no page names the screw); its head a slotted disc, the insert a ring with its hole on the left.","The drum is a disc with five through-holes and its hub, without the numerals and the arrow; the lettering (\"DANIEL DEFENSE\", \"DD-11002 U.S. PAT. ...\") isn't drawn. Edges are broken by a small bevel."],"ledger":["daniel-defense-fixed-rear-sight.length","daniel-defense-fixed-rear-sight.width","daniel-defense-fixed-rear-sight.height","daniel-defense-fixed-rear-sight.height_drawn","daniel-defense-fixed-rear-sight.sight_line_above_rail","daniel-defense-fixed-rear-sight.clamp_below_rail","daniel-defense-fixed-rear-sight.screw_behind_front","daniel-defense-fixed-rear-sight.drum_d","daniel-defense-fixed-rear-sight.drum_behind_front"]},"profiles":{"side":{"plane":"xy","origin":"the base's front face at the jaws' feet; offset to the clamp's middle on the rail's top","offset":{"x":"front_x","y":"clamp_bottom_y"},"points":[[-1.38,0.214],[-1.375,0.209],[-1.332,0.211],[-1.259,0.198],[-1.162,0.155],[-1.121,0.128],[-1.069,0.077],[-1.013,0],[-0.005,0],[0,0.004],[0,1.557],[-0.013,1.605],[-0.041,1.657],[-0.08,1.696],[-0.136,1.727],[-0.559,1.803],[-0.623,1.806],[-0.673,1.804],[-0.737,1.787],[-0.787,1.769],[-0.846,1.736],[-0.904,1.687],[-1.108,1.482],[-1.149,1.42],[-1.164,1.359],[-1.163,1.248],[-1.171,1.212],[-1.176,1.114],[-1.196,0.995],[-1.217,0.924],[-1.216,0.907],[-1.223,0.897],[-1.272,0.732],[-1.352,0.547],[-1.377,0.446]],"features":{"drum":[[[-0.972,1.662],[-0.191,1.662],[-0.191,0.882],[-0.972,0.882]]],"hub":[[[-0.718,1.408],[-0.446,1.408],[-0.446,1.137],[-0.718,1.137]]],"screw_head":[[[-0.484,0.408],[-0.102,0.408],[-0.102,0.023],[-0.484,0.023]]]},"scaleRefs":["daniel-defense-fixed-rear-sight.length"],"inputs":{"daniel-defense-fixed-rear-sight.length":1.38},"tolerance":0.004,"photo":"references/daniel-defense-fixed-rear-sight 2b28fd900eb7 (US D631,935 S (Daniel Defense, 'Rear firearm sight'), FIG. 5, the drum side, the muzzle to the viewer's right (the sight's right); the patent office's copy, page 6, 300 dpi)","method":"luminance < 128, inside [440, 640, 1990, 2640], closing ×3, largest piece, holes filled, inset 2 px (half the outline's stroke); scale from daniel-defense-fixed-rear-sight.length = 1.38 in (x-extent 1453 px → 1052.9 px/in); origin at x max, y min of the outline; Douglas-Peucker at 0.004 in with the extremes kept: 35 points (IoU 0.997 with the full outline); features through the same placement (drum: the drum's outer circle (centre u 1326, v 1253; 822 px across); hub: the hub's circle in the drum's middle (286 px across); screw_head: the clamp screw's slotted head (centre u 1630, v 2366)) (tools/trace.py)","via":"harvest","note":"The sight's right side: the drum high in the middle, the clamp screw's head low toward the front, the concave relief under the rear end."},"rear":{"plane":"zy","origin":"midway between the feet (the walls' middle, the window's and the split's); the feet, offset to the rail's top","offset":{"y":"clamp_bottom_y"},"points":[[-0.628,0.28],[-0.628,0.132],[-0.601,0.062],[-0.57,0.024],[-0.527,0],[-0.489,0],[-0.488,0.228],[0.49,0.228],[0.49,0],[0.522,0],[0.575,0.024],[0.605,0.062],[0.621,0.097],[0.628,0.132],[0.628,0.28],[0.607,0.369],[0.568,0.415],[0.49,0.459],[0.442,0.505],[0.42,0.549],[0.408,0.594],[0.406,1.806],[0.303,1.806],[0.303,1.451],[0.296,1.415],[0.28,1.381],[0.255,1.362],[0.222,1.352],[-0.22,1.352],[-0.249,1.359],[-0.276,1.379],[-0.296,1.415],[-0.303,1.451],[-0.303,1.806],[-0.403,1.806],[-0.408,0.593],[-0.418,0.549],[-0.44,0.504],[-0.49,0.459],[-0.568,0.415],[-0.608,0.369]],"features":{"window":[[[-0.344,0.86],[0.346,0.86],[0.346,0.375],[-0.344,0.375]]],"split":[[[-0.028,0.375],[0.031,0.375],[0.031,0.228],[-0.028,0.228]]],"ceiling":[[[-0.314,0.228],[0.341,0.228],[0.341,0.228],[-0.314,0.228]]],"aperture_leg":[[[-0.181,1.773],[0.18,1.773],[0.18,1.323],[-0.181,1.323]]],"aperture_hole":[[[-0.093,1.686],[0.102,1.686],[0.102,1.491],[-0.093,1.491]]],"walls":[[[-0.403,1.806],[-0.303,1.806],[-0.303,1.353],[-0.403,1.353]],[[0.303,1.806],[0.406,1.806],[0.406,1.353],[0.303,1.353]]],"drum":[[[0.406,1.653],[0.449,1.653],[0.449,0.894],[0.406,0.894]]],"hub":[[[0.449,1.409],[0.625,1.409],[0.625,1.136],[0.449,1.136]]],"left_head":[[[-0.461,1.407],[-0.403,1.407],[-0.403,1.145],[-0.461,1.145]]],"screw_head":[[[0.627,0.405],[0.662,0.405],[0.662,0.084],[0.627,0.084]]]},"scaleRefs":["daniel-defense-fixed-rear-sight.height_drawn"],"inputs":{"daniel-defense-fixed-rear-sight.height_drawn":1.806},"tolerance":0.004,"photo":"references/daniel-defense-fixed-rear-sight 19d661203cc6 (US D631,935 S, FIG. 4, the rear view from the breech (the drum at the viewer's right: the sight's right is +z); page 5, 300 dpi)","method":"manual polygon (44 points picked on the photo); scale from daniel-defense-fixed-rear-sight.height_drawn = 1.806 in (y-extent 2000 px → 1107.4 px/in); origin at x center, y min of the outline; Douglas-Peucker at 0.004 in with the extremes kept: 41 points (IoU 0.997 with the full outline); features through the same placement (window: the through-cut window (sides u 902, 1666 along row 1800; top v 1656, floor v 2193.5); split: the base's split from the window's floor to the channel (walls u 1252, 1317); ceiling: the channel's ceiling: the rail's top (row 2356, columns 1000 and 1500); aperture_leg: the standing aperture leg: its sides (u 1082, 1481.5 on row 855), its round top (v 645) and its foot on the floor (v 1143); aperture_hole: the large aperture's hole (u 1179 to 1395.5, v 741 to 957); walls: the tower walls' outer faces (u 836, 1732) and inner faces (u 947, 1618), from their top (v 609) to the U's floor (v 1110); drum: the drum's disc edge on: from the wall (u 1732) to its face (u 1779.5), rows 778 to 1619; hub: the drum's hub: to its end (u 1975), rows 1048.5 to 1351; left_head: the windage screw's slotted end beyond the left wall (u 772 to 836), rows 1050 to 1340; screw_head: the clamp screw's head beyond the right foot (u 1977 to 2016)) (tools/trace.py)","via":"harvest","note":"The whole sight from behind, the hardware left out: the two tower walls and the U between them, the window, the base flaring to its feet, the channel."},"plan":{"plane":"xz","origin":"the base's front face, midway across; offset to the clamp's middle","offset":{"x":"front_x"},"points":[[-1.38,0.406],[-1.38,-0.398],[-0.524,-0.628],[-0.133,-0.628],[0,-0.553],[0,0],[0,0.412],[0,0.554],[-0.074,0.628],[-0.244,0.628],[-0.495,0.628]],"scaleRefs":["daniel-defense-fixed-rear-sight.length"],"inputs":{"daniel-defense-fixed-rear-sight.length":1.38},"tolerance":0.004,"photo":"references/daniel-defense-fixed-rear-sight bf25db3e954e (US D631,935 S, FIG. 8, the bottom view (the muzzle to the viewer's right); page 9, 300 dpi)","method":"manual polygon (8 points picked on the photo); rotated +180.0° as declared; scale from daniel-defense-fixed-rear-sight.length = 1.38 in (x-extent 1559 px → 1129.7 px/in); origin at x max, y center of the outline; Douglas-Peucker at 0.004 in with the extremes kept: 11 points (IoU 0.999 with the full outline) (tools/trace.py)","via":"harvest","note":"From below: the feet's outline, wider at the front, tapering at the rear over the relief."}},"gaps":[{"what":"The sight line's height as a maker's figure: no page states it (Wing's \"Center Height Over Rail: Rear: 1.54\"\" is the aperture's top); the patent's 1.363 and Wing's end-on photo's 1.41 differ","need":"A maker's or seller's figure for the aperture's centre over the rail, or a square side photo of the sight on a rail with the aperture's ring in profile"},{"what":"The width's span (TLO's 1.24 in) and the overall height (TLO's 1.78 against the patent's 1.81 at the length's scale)","need":"A second seller's table, or a dimensioned drawing"},{"what":"Mil-Spec+ Brown and Tornado Grey are sold only in the set and aren't offered: no colour matched","need":"make color-match on GRITR Outdoors' brown photos (5ae12c63efa9, f1fb888cfd05); a photograph of the Tornado Grey set"},{"what":"danieldefense.com refuses the reader (D59): no maker's page, drawing or manual","need":"Pages of Daniel Defense's the user saves from their own browser"}]},"dead-air-rxd22ti":{"id":"dead-air-rxd22ti","name":"RXD22Ti","manufacturer":"Dead Air","sku":"RXD22TiBLK","url":"https://deadairsilencers.com/rxd22ti/","category":"suppressor","description":"Dead Air's and Ruger's rimfire suppressor: a titanium tube Cerakoted black or Burnt Bronze, with a wrench hex and eight long flats, round a 3D-printed single-piece core, a castellated front cap ring, and the core's black flange at the rear. It screws onto Dead Air's XRF brake (a part of its own, in the box) until it bottoms on the brake's taper.","weight":"dead-air-rxd22ti.weight","nfa":"silencer","cartridge":{"takes":[".22 LR",".22 WMR",".17 HMR",".17 WSM","5.7x28mm"],"stated":"Caliber Rating .22LR, 22Mag, 17HMR, 17WSM, 5.7x28* (the asterisk, the manual p. 3: \"While rated for semiautomatic use with 5.7x28 ammunition, some platform and ammunition combinations may result in poor performance and/or damage to your suppressor.\"); the manual p. 6: \"THE RXD22TI IS RATED FOR .22 WINCHESTER MAGNUM RIMFIRE AND 5.7X28MM. IT IS OPTIMIZED FOR .22 LONG RIFLE (LR).\"","source":"https://deadairsilencers.com/rxd22ti/ (harvest.quote); Dead Air, RXD22Ti owner's manual (https://deadairsilencers.com/content/pdfs/RXD22Ti%20Manual.pdf). Ruger's page says \".22 LR (full-auto*), .17 HMR, .22 WSM (semiauto)\" and its news \".22 LR, .22 WSM, .17 HMR, 4.6mm, and 5.7x28mm\": Dead Air's own list is taken."},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"mount":{"origin":[0,0,0],"note":"Suppressor frame: on its axis at its rear face, the core's flange, +x toward the muzzle. On the XRF brake that face comes down to the front of the brake's hex (the brake's `suppressor_seat`)."},"front":{"origin":["{.length}",0,0],"note":"The front cap ring's front: where the build's overall length ends."}},"interfaces":{"mount":{"type":"suppressor_mount","role":"suppressor","anchor":"mount","params":{"system":"dead-air-xrf"},"flips":false,"note":"Dead Air's XRF brake (RXD674, 1/2-28; RXD675, M10x1). Dead Air's page: \"What's Included Xeno Rimfire Muzzle Brake | RXD674\"; the manual: \"Your RXD22Ti comes with a XRF muzzle device in the box ... The XRF muzzle device is specially designed to work with the RXD22Ti. Thread the muzzle device onto your host firearm or into the suppressor until it bottoms out on the taper.\" (p. 6). As a direct-thread can, the same pair: \"Note: The RXD22Ti is designed such that if you want to have a direct thread only suppressor you may torque the XRF muzzle device into the suppressor core with a 1-1/16\", 27mm, and 3/4\" wrench or the supplied tools, to 15 foot-pounds.\" Barrel lengths: \"Barrel Restrictions None\" (Dead Air's page)."}},"materials":{"body":{"label":"Tube","finish":"cerakote","recolorable":false,"color":"dead-air-black-cerakote","options":{"black":{"label":"Black","finish":"cerakote","color":"dead-air-black-cerakote","sku":"RXD22TiBLK","source":"https://deadairsilencers.com/rxd22ti/"},"burnt_bronze":{"label":"Burnt Bronze","finish":"cerakote","color":"dead-air-burnt-bronze-cerakote","sku":"RXD22TiBB","source":"https://deadairsilencers.com/rxd22ti/"}},"default":"black","note":"The titanium tube: its rear band, its wrench hex, its flats. Dead Air: \"Materials 6AL4V Titanium\", \"Finish Black and Burnt Bronze Cerakote\", \"Part Number RXD22TiBLK, RXD22TiBB\" (https://deadairsilencers.com/rxd22ti/). The black is photographed whole (Midwest Gun Works, e5d4c6005c19; Soldier Systems, aa413639ea63; Ruger's parts apart, 0b575e192b3a); the Burnt Bronze only as Ruger's photo of the parts apart (7b58ad4e444d), where the tube is bronze and the core, the ring and the XRF are black."},"core":{"label":"Core's flange and front cap ring","finish":"nitride","recolorable":false,"color":"steel-nitride-black","note":"Black in both colourways (Ruger's photos of the parts apart, black 0b575e192b3a and Burnt Bronze 7b58ad4e444d): the core's rear flange, the front cap ring and the core's front face inside it. Dead Air: \"a 3D printed PVD coated single-piece Triskelion™ core, titanium retaining cap\". The catalog has no finish for a PVD coat on titanium: drawn as its smooth black on metal (`nitride`). On Midwest Gun Works' photo the ring's lit edge reads grey; the coat itself isn't fitted."}},"components":{"body":{"label":"Tube","material":"body"},"core":{"label":"Core's flange and front cap ring","material":"core"}},"geometry":{"model":"dead-air-rxd22ti.glb","components":{},"approximations":["The outside only, turned from stations read on Midwest Gun Works' straight side view of RXD22TIBLK on its XRF (e5d4c6005c19), scaled along by Dead Air's 5.6 in over the pair and across by its 1.1 in over the tube (the black tube reads 3.1% thin at the length's scale).","The core's rear flange (a hex, its flats drawn at the tube's hex's share of its corners: not read), the tube's rear band, the grooves either side of its wrench hex (its flats read on the faces' widths), the round tube, the ring groove near its front, the front cap ring standing 0.10 in out of the tube with six notches in its lip, and the core's front face recessed inside the ring with the exit hole.","The eight flats down the tube are shallow round grooves, each running out at the tube's surface at its rear end and 0.04 in deep (assumed: the flat's width and the silhouette's dip don't agree on one shape) and flute_width wide at its front end, square across there; the real ones run a little slant across at their front ends, and may twist, which isn't drawn.","Behind its skin the model is solid but for the bore and the socket the XRF goes in (the XRF's own outside from its ledger, at the seat the two share, with no clearance; the thread in it is drawn at the XRF's crests, plain): the core inside isn't modelled, and the model's volume is no measure of its weight.","Not drawn: the engravings (RXD, the Ruger and Dead Air marks, RXD RXD22Ti 22 CAL), the core's printed texture where it shows, the tube's thread under the ring."],"ledger":["dead-air-rxd22ti.overall_length_with_mount","dead-air-rxd22ti.od","dead-air-rxd22ti.length","dead-air-rxd22ti.flange_end_x","dead-air-rxd22ti.flange_chamfer_x","dead-air-rxd22ti.flange_rear_d","dead-air-rxd22ti.flange_d","dead-air-rxd22ti.flange_flats","dead-air-rxd22ti.band_x","dead-air-rxd22ti.band_d","dead-air-rxd22ti.band_end_x","dead-air-rxd22ti.groove_d","dead-air-rxd22ti.hex_x","dead-air-rxd22ti.hex_end_x","dead-air-rxd22ti.hex_corner_d","dead-air-rxd22ti.hex_flats","dead-air-rxd22ti.tube_x","dead-air-rxd22ti.flutes","dead-air-rxd22ti.flute_x","dead-air-rxd22ti.flute_end_x","dead-air-rxd22ti.flute_width","dead-air-rxd22ti.flute_depth","dead-air-rxd22ti.front_groove_x","dead-air-rxd22ti.front_groove_width","dead-air-rxd22ti.front_groove_depth","dead-air-rxd22ti.tube_front_x","dead-air-rxd22ti.ring_od","dead-air-rxd22ti.ring_notches","dead-air-rxd22ti.ring_notch_width","dead-air-rxd22ti.ring_notch_depth","dead-air-rxd22ti.ring_front_round","dead-air-rxd22ti.ring_bore_d","dead-air-rxd22ti.exit_bore_d","dead-air-rxd22ti.core_face_inset"]},"profiles":{},"gaps":[{"what":"The front end square on: the ring's inside, its notches' size, the core's front face and its hole","need":"a photo straight into the front end"},{"what":"The core's flange flats, and the wrench sizes the manual names (1-1/16 in, 27 mm) against the tube's hex as read (0.97 in)","need":"Dead Air's drawing, or a view along the axis from the rear"},{"what":"The Burnt Bronze tube assembled, and its colour under the app's light","need":"a seller's photo of RXD22TiBB whole; then `make color-match`"}]},"dead-air-xrf-brake":{"id":"dead-air-xrf-brake","name":"XRF Xeno Rimfire Muzzle Brake","manufacturer":"Dead Air","sku":"RXD674","url":"https://deadairsilencers.com/xrf-xeno-rimfire-muzzle-brake/","category":"muzzle_device","description":"Dead Air's rimfire muzzle brake for its RXD22Ti: a short black-nitrided 17-4 stainless body with a hex at its rear, the thread the suppressor's core screws onto, a steep taper it locks on, and one port straight through its nose. A brake on its own, or the RXD22Ti's quick-detach mount (it comes in that suppressor's box).","weight":"dead-air-xrf-brake.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"thread":{"origin":[0,0,0],"note":"Device frame: on the bore axis at the barrel's shoulder, +x toward the muzzle. The rear face bears on the shoulder (the manual: \"until the rear of the XRF muzzle device mates to the shoulder of the barrel\")."},"front":{"origin":["{.length}",0,0],"note":"The nose's front face: where the build's overall length ends without a suppressor."},"suppressor_seat":{"origin":["{.suppressor_seat_x}",0,0],"note":"On the bore axis where the RXD22Ti's rear face (its core's flange) stands when it is threaded on and bottoms out on the taper: the front of the hex's chamfer, read on this device's own photo and on the photo of the two together."}},"interfaces":{"thread":{"type":"muzzle_thread","role":"device","anchor":"thread","params":{"thread":"1/2-28"},"flips":false,"note":"Dead Air: \"Thread Pitch 1/2-28\" (the page's choice for RXD674; RXD675 is the M10x1 one); the manual: \"Align the XRF muzzle device with the threads on your firearm and rotate the muzzle device on the barrel with a clockwise motion until the rear of the XRF muzzle device mates to the shoulder of the barrel.\" and \"torque the muzzle device to the barrel at 20 foot-pounds\" (p. 6). No source gives how long a barrel thread it takes: no thread_length."},"suppressor_mount":{"type":"suppressor_mount","role":"device","anchor":"suppressor_seat","params":{"system":"dead-air-xrf"},"flips":false,"note":"Dead Air, on its page: \"The Dead Air XRF Rimfire Muzzle Brakes offer a streamlined quick-detach mounting system paired with the performance of a single-port brake design, enhancing overall suppressor efficiency. Engineered for the RXD22Ti suppressor is a uniquely tapered rimfire muzzle device, designed for a secure, repeatable lockup across multiple platforms utilizing ½\"-28 and M10x1 thread patterns.\" The manual: \"Thread the muzzle device onto your host firearm or into the suppressor until it bottoms out on the taper. Note that the XRF muzzle device has a very steep taper angle which results in a rock-solid lock up with very low torque. Lightly hand tightening the suppressor on to the XRF mount will result in the suppressor staying attached to the muzzle device.\" (p. 6). The system's name is the maker's word for the device, XRF."}},"materials":{"body":{"label":"Brake","finish":"nitride","recolorable":false,"color":"steel-nitride-black","note":"One colour. Dead Air: \"Material 17-4PH Stainless Steel\", \"Finish Nitride\", \"Color Black\" (https://deadairsilencers.com/xrf-xeno-rimfire-muzzle-brake/). A smooth satin black in Dead Air's and Midwest Gun Works' photos (222c079d4c69, 8425e22cd635). The markings (\"1/2-28\", \"RXD674\") aren't drawn."}},"components":{"body":{"label":"Brake","material":"body"}},"geometry":{"model":"dead-air-xrf-brake.glb","components":{},"approximations":["Every size but the length, the diameter and the hex's flats is read on one photo of RXD674 standing (Midwest Gun Works, 8425e22cd635), from the side and 13 degrees above, scaled by Dead Air's 1.16 in and 0.81 in, which agree on it within 1.4%.","Turned: the hex's corners, its front chamfer, the groove, the thread's lead-in, the neck, the taper's collar, the taper and the nose. Then cut: the hex's six flats (0.75 in across, assumed from the manual's 3/4 in wrench), the thread the suppressor's core screws onto (a helix at the photo's pitch, between its crests and the groove's depth), one port through the nose (a slot with round ends, square to the axis, through both walls), the barrel's 1/2-28 socket (plain, at the thread's crests) carried on as a room to an assumed front wall, and the bore through that wall.","Which way round the port faces is the barrel's to say (the brake stops where it bears on the shoulder): drawn opening to the sides, as a brake vents.","The inside isn't sourced (Dead Air: it \"helps capture lead and debris before it enters the suppressor\"): drawn as the barrel's socket carried on at its size to a front wall 0.08 in thick (assumed), the port opening into it; with that room the model's 17-4 weighs the published 1.05 oz within a few percent."],"ledger":["dead-air-xrf-brake.overall_length","dead-air-xrf-brake.od","dead-air-xrf-brake.hex_flats","dead-air-xrf-brake.hex_end_x","dead-air-xrf-brake.suppressor_seat_x","dead-air-xrf-brake.groove_d","dead-air-xrf-brake.thread_x","dead-air-xrf-brake.thread_end_x","dead-air-xrf-brake.thread_major_d","dead-air-xrf-brake.thread_pitch","dead-air-xrf-brake.lead_end_x","dead-air-xrf-brake.neck_d","dead-air-xrf-brake.collar_x","dead-air-xrf-brake.collar_d","dead-air-xrf-brake.taper_x","dead-air-xrf-brake.taper_end_x","dead-air-xrf-brake.taper_front_d","dead-air-xrf-brake.body_d","dead-air-xrf-brake.front_round","dead-air-xrf-brake.bore_d","dead-air-xrf-brake.port_x","dead-air-xrf-brake.port_length","dead-air-xrf-brake.port_width","dead-air-xrf-brake.chamber_front_wall","dead-air-xrf-brake.barrel_thread_major_d"]},"profiles":{},"gaps":[{"what":"The hex's flats, and which flat is where","need":"a view straight along the axis, or Dead Air's drawing; 0.75 in is assumed from the manual's wrench"},{"what":"The thread the suppressor screws onto: its size and pitch as the maker states them","need":"Dead Air's drawing or a page that names it; read on one photo at 0.814 in and 0.0375 in"},{"what":"The inside: how deep the barrel's thread runs, the lead-catching room and its front wall, how the port opens into it","need":"a section, or photos straight into both ends"}]},"eotech-exps3":{"id":"eotech-exps3","name":"HWS EXPS3 holographic weapon sight, 1-Dot Speed Ring","manufacturer":"EOTECH","sku":"EXPS3-0","url":"https://www.eotechinc.com/products/eotech-hws-exps3","category":"optic","description":"EOTECH's HWS EXPS3, a 1x holographic sight with a 1.20 x 0.85 in window under an aluminium hood, on its own quick-detach base: \"Equipped with a 7mm raised quick-detach base for lower 1/3 iron sight co-witness\", \"Side buttons for easy adjustments with a magnifier\", \"Includes night vision compatible settings\" (EOTECH's catalog). One CR123 battery, across the front. EXPS3-0 is the reticle EOTECH calls the 1-Dot Speed Ring: \"68 MOA circle with quadrant ticks with 1 MOA aiming dot\".","weight":"eotech-exps3.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":[0,0,0],"note":"Optic frame: on the rail's top under the cross bolt, on the rail's centre plane, +x forward. EOTECH's manual, p. 13: \"The sight contains a small cross bolt that rests in the groove of the Picatinny rail. Move the sight to the position desired on the rail and allow the post to rest fully in the closest groove.\" The bolt lies in the slot the build names."},"optical_axis":{"origin":[0,"{.optical_axis_above_rail}",0],"note":"The window's centre: EOTECH states no height of the reticle over the rail, and a hologram's reticle has no axis of its own in the window."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":"={.clamp_rear}","clamp_front":"={.clamp_front}"},"flips":false,"note":"One cross bolt, a third of the base's length from its front: the base reaches 1.77 in behind the bolt and 0.93 in ahead of it (2.70 in of rail). EOTECH's manual, p. 13: \"Push the sight as far forward as possible and close the quick-detach lever so it is fully shut and nested in the base of the sight.\" It mounts on \"either a 1\\\" (25.4mm) Weaver or MIL-STD-1913 rail\"."},"sight_line":{"type":"optic.sight_line","role":"sight","params":{"magnification":"1x"},"flips":false,"note":"EOTECH's manual, p. 9: \"Magnification 1X\", \"Eye Relief Unlimited\". The eye can be anywhere behind it, so it has no eye point of its own. Its catalog: \"Side buttons for easy adjustments with a magnifier\": a magnifier goes behind it."}},"materials":{"body":{"label":"Hood and base","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized_matte","color":"placeholder-black","sku":"EXPS3-0","source":"https://www.eotechinc.com/products/eotech-hws-exps3.js"},"tan":{"label":"Tan","finish":"cerakote","color":"eotech-tan","sku":"EXPS3-0TAN","source":"https://www.eotechinc.com/products/eotech-hws-exps3.js"}},"default":"black","note":"The two colours EOTECH sells this sight in: its own product data lists \"Black / 1-Dot Speed Ring\" (EXPS3-0) and \"Tan / 1-Dot Speed Ring\" (EXPS3-0TAN); its manual, \"Color/Finish Black or Flat Dark Earth (Tan)\". The hood is aluminium (the manual: \"Protective Aluminum Hood: Preassembled protective hood increases durability of sight housing\"). Primary Arms, of the black sight: \"Color Black\", \"Finish Hardcoat Anodized\"; of the tan one: \"Color Tan\", \"Finish Cerakote\", \"Material Aluminum\". The base's block is the hood's colour in both (Primary Arms' and EOTECH's side views of each). Tan is matched to the hood's flats in Primary Arms' two side views of EXPS3-0TAN; black is the placeholder the other optics use. The maker's marks and the warning label aren't drawn."},"housing":{"label":"Housing, battery compartment and cap","finish":"polymer","recolorable":false,"color":"placeholder-polymer-black","follows":{"slot":"body","options":{"tan":{"finish":"polymer","color":"eotech-tan-polymer"}}},"note":"What the hood stands over: the window's frame, the floors of the two adjusters' recesses, the battery compartment across the front and its cap. On the tan sight it is tan too, a browner and darker one than the hood's coating with none of its speckle (Primary Arms' left view: the battery compartment #928272 beside a hood of #a19285; EOTECH's own pictures of the tan sight have the two a like tone). No page on file names its material: drawn as moulded polymer by its surface in the photos. The cap's black seal and its lanyard aren't drawn."},"clamp":{"label":"Quick-detach lever","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","follows":{"slot":"body","options":{"tan":{"finish":"anodized_matte","color":"eotech-tan-lever"}}},"note":"The quick-detach lever along the base's left side and its locking latch ahead of it (EOTECH's manual, Figure 1: \"Quick-Detach Lever\", \"Locking Latch\"). Black on the black sight. On the tan one it is a bare-looking anodized metal, not the hood's coating: an olive gold in Primary Arms' photos (#a29277), a redder bronze in EOTECH's own (#a07857 beside a hood of #8f796b). No page states its finish: drawn as matte anodize, matched to Primary Arms' left view, the light the hood's tan is matched in. In Primary Arms' photos, of an older sight (its rear cover is marked L3 EOTech), the latch is a bare grey; in EOTECH's current pictures it is the lever's bronze, which is what is drawn. The plate of the same metal round the adjustment nut on the base's right side isn't drawn (no outline of it is traced)."},"cover":{"label":"Rear cover","finish":"polymer","recolorable":false,"color":"placeholder-polymer-black","note":"The cover under the window at the rear, and the black beside it at its left: black on both sights (Primary Arms' views from behind of the black and the tan one; EOTECH's exps3_tanbr), a moulded piece with the maker's mark in it. Its two lower screws are in the outline and are drawn as the cover's."},"buttons":{"label":"Buttons","finish":"rubber","recolorable":false,"color":"eotech-button-grey","note":"The night vision button and the two brightness buttons: a dark grey rubber on both sights, lighter than the black round them (Primary Arms' left views: #494c51 and #4d5055 on the tan sight, #424244 on the black one). Their arrows and the letters NV aren't drawn."},"hardware":{"label":"Adjusters, screws and nut","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The two slotted adjusters, the hood's three screws, the rear cover's two upper screws, the adjustment nut on the cross bolt's right end and the lever's cam: black on both sights (Primary Arms' and EOTECH's side views of the tan one, where they stand out of the tan). Drawn as dark steel; no page names their metal or finish."},"lens":{"label":"Windows","finish":"glass","recolorable":false,"color":"glass-clear","note":"EOTECH's manual: \"Front Window Material Glass 1/8\\\" (3.17mm) thick\", \"Rear Window Material Laminate 3/16\\\" (4.76mm) thick\", \"Anti-reflection coating on external surfaces\"."}},"components":{"body":{"label":"Hood and base","material":"body"},"housing":{"label":"Housing, battery compartment and cap","material":"housing"},"clamp":{"label":"Quick-detach lever","material":"clamp"},"cover":{"label":"Rear cover","material":"cover"},"buttons":{"label":"Buttons","material":"buttons"},"hardware":{"label":"Adjusters, screws and nut","material":"hardware"},"lens":{"label":"Windows","material":"lens"}},"geometry":{"model":"eotech-exps3.glb","components":{},"approximations":["A visual hull of three straight views (Primary Arms' left side view and its view from behind, EOTECH's view from above), each placed by the hood's top: a section is what the three outlines allow. The housing under the hood is as wide as the hood's flanks all the way down, the battery compartment is the side view's outline between its two ends, and the hood's bends are the view from behind's.","The gap between the hood and the window's frame is the one the view from behind shows, run the hood's length (seen from behind it is a little narrower than it is, the hood's and the frame's walls going away from the lens). The frame's front face is a plane where the hood's front edge stands at the window's top; ahead of it everything inside the hood is open down to the battery compartment's top, which is flat here and really sweeps up to the window's lower edge.","The window is the published 1.20 x 0.85 in opening, its corners 0.18 in, on the rail's centre plane, its centre 0.79 in under the hood's top as two views from behind read it: 1.86 in over the rail (EOTECH states no height). The rear laminate and the front glass are at their published thicknesses, each set half its own thickness inside the frame's face: their real recesses, the hologram between them and the reticle aren't drawn.","The rail's top is where EOTECH's picture of the current rear cover has the roof of its notch (2.65 in under the hood's top); the older cover in Primary Arms' photos, which the outline from behind is, stands 0.07 in clear of the rail behind the base. The rail's channel is the standard's rail head cut out along the base: the jaws follow its lower faces to the lower gauge line and stand straight below it. The cross bolt across the channel isn't drawn (its size isn't sourced), so nothing of the sight stands in the rail's slot. It is drawn with the bolt on the slot's centre; pushed forward as the manual says, it is ahead by the bolt's play in the slot.","The quick-detach lever is what the view from behind has hanging lowest at the far left, run along the base from its rear end to the front end of the locking latch (the side view's box): one plain bar, the lever and the latch not told apart, its top where the view from behind has it (in the side photos the lever's top rises toward its cam, under the hood's edge, which the hull has lower there). The lever's cam is a plain pad on it. Until 2026-10-06 the bar was drawn ahead of the cam only: the side photos have the lever from the cam to the base's rear. The adjustment nut is a plain round standing 0.6 of its radius out of the base's right side; the plate round it isn't drawn.","The pieces are told apart, for their colours, where the photos have them (2026-10-06): the hood is the hull's outer 0.10 in on each flank (its thickness) and everything outside the gap round the window's frame; the housing is what is inside that, above the base's top (the right side view's), with the battery compartment and its cap; the rear cover is the hull behind the hood's thickness over the view from behind's cover plate, with what is black beside it on the left taken as the cover's. The base's block is one piece with the hood, as it is one colour with it in both colourways. The hull is solid: the air between the hood's plate and the housing below the window isn't drawn, so the housing shows at the hood's front and rear edges where the real one has a shadow.","The adjusters' recesses are round holes through the hood's right flank (its thickness, 0.10 in) to the housing under it, each with a round dial standing on the housing, slotted as the photo has it; the night vision button in its ring, the two brightness buttons in their pad and the hood's and the rear cover's screws stand out by shares of the hood's thickness. How far each really stands isn't sourced; the slots' depths are shares of it too, and the buttons' arrows, the click marks, the label and the maker's marks aren't drawn.","The battery cap is a knurled round of 41 teeth (counted on its rim: 41, give or take one) from the battery compartment's right end to its face; with its coin slot as the photo has it turned; its lanyard and the mark on its face aren't drawn. The hood's flanks end ahead in the edge each side photo shows.","Solid: 13 cubic inches, which as aluminium would weigh 20 oz against the published 11.2 oz. The real housing is hollow, and its battery compartment, rear cover and buttons are plastic and rubber."],"ledger":["eotech-exps3.length","eotech-exps3.width","eotech-exps3.height","eotech-exps3.optical_axis_above_rail","eotech-exps3.window_width","eotech-exps3.window_height","eotech-exps3.mount_length","eotech-exps3.clamp_rear","eotech-exps3.clamp_front","eotech-exps3.top_above_rail","eotech-exps3.hood_width","eotech-exps3.hood_thickness"]},"profiles":{"side":{"plane":"xy","origin":"the heads of the rear cover's lower screws (the outline's rear extreme), the hood's top; offset to the cross bolt and the rail's top","offset":{"x":"side_rear_x","y":"top_above_rail"},"points":[[0,-2.466],[0.002,-2.574],[0.017,-2.633],[0.035,-2.647],[0.155,-2.657],[0.158,-2.849],[0.176,-2.869],[2.095,-2.883],[2.217,-2.895],[2.294,-2.919],[2.688,-2.905],[2.841,-2.859],[2.847,-2.409],[2.845,-2.354],[2.826,-2.294],[2.833,-2.213],[2.823,-2.189],[2.829,-2.183],[2.887,-2.235],[2.949,-2.276],[3.097,-2.331],[3.305,-2.336],[3.408,-2.312],[3.477,-2.281],[3.559,-2.228],[3.672,-2.11],[3.739,-1.983],[3.775,-1.809],[3.749,-1.62],[3.694,-1.495],[3.592,-1.377],[3.467,-1.287],[3.475,-1.279],[3.496,-1.296],[3.492,-1.284],[3.382,-1.212],[3.281,-1.181],[3.152,-1.171],[3.143,-1.16],[3.006,-1.16],[2.99,-1.167],[2.345,-1.154],[2.345,-1.001],[2.3,-0.893],[2.271,-0.795],[2.161,-0.152],[2.147,-0.099],[2.13,-0.092],[2.115,0],[0.568,-0.01],[0.519,-0.042],[0.5,-0.147],[0.538,-0.326],[0.545,-0.491],[0.531,-0.613],[0.509,-0.699],[0.464,-0.814],[0.414,-0.903],[0.351,-0.981],[0.17,-1.149],[0.134,-1.204],[0.11,-1.283],[0.043,-1.629],[0.029,-1.746],[0.029,-2.347],[0.007,-2.394]],"features":{"nv_boss":[[[0.675,-1.18],[0.221,-1.18],[0.221,-1.634],[0.675,-1.634]]],"nv_button":[[[0.563,-1.292],[0.334,-1.292],[0.334,-1.522],[0.563,-1.522]]],"button_pad":[[[1.173,-1.833],[0.145,-1.833],[0.145,-2.366],[1.173,-2.366]]],"buttons":[[[1.034,-1.964],[0.735,-1.964],[0.735,-2.256],[1.034,-2.256]],[[0.556,-1.964],[0.25,-1.964],[0.25,-2.256],[0.556,-2.256]]],"screws":[[[2.497,-2.155],[2.335,-2.155],[2.335,-2.318],[2.497,-2.318]],[[1.522,-2.155],[1.359,-2.155],[1.359,-2.318],[1.522,-2.318]]],"lever":[[[2.698,-2.488],[2.27,-2.488],[2.27,-2.806],[2.698,-2.806]]],"cam":[[[2.134,-2.442],[1.775,-2.442],[1.775,-2.7],[2.134,-2.7]]],"plate_front":[[[2.368,-1.189],[2.421,-1.295],[2.516,-1.414],[2.6,-1.534],[2.66,-1.653],[2.696,-1.773],[2.708,-1.964],[2.708,-2.299],[3.186,-2.299],[3.186,-1.189]]]},"scaleRefs":["eotech-exps3.length","eotech-exps3.height"],"inputs":{"eotech-exps3.height":2.9,"eotech-exps3.length":3.8},"tolerance":0.006,"photo":"references/eotech-exps3 29f6391862ba (Primary Arms EXPS3-0_05: the black sight's left side straight on, on white, 2200 x 1467 (the muzzle to the left))","method":"luminance < 235, 1 boxes excluded, opening ×1, closing ×2, largest piece, holes filled; scale from eotech-exps3.length = 3.8 in (x-extent 1579 px → 415.5 px/in) and eotech-exps3.height = 2.9 in (y-extent 1221 px → 421.0 px/in), which agree within 1.3%; mean 418.3 px/in; origin at x min, y max of the outline; Douglas-Peucker at 0.006 in with the extremes kept: 66 points (IoU 0.997 with the full outline); features through the same placement (nv_boss: the raised ring round the night vision button (a circle: its box); nv_button: the night vision button (a circle: its box); button_pad: the raised pad the two brightness buttons sit in; buttons: the down and up brightness buttons; screws: the hood's two screws on the left flank (circles: their boxes); lever: the quick-detach lever's paddle, closed and nested in the base; cam: the lever's cam, on the cross bolt's axis; plate_front: what is ahead of the hood's left flank below the battery compartment's top: the flank's front edge, a bright line down the photo picked every 40 to 50 rows on a 1.6x gridded crop (the battery compartment is behind it in this view, so the outline doesn't have it)) (tools/trace.py)","via":"harvest","note":"The left flank: the buttons' side, and the quick-detach lever's. The label and the maker's mark aren't drawn."},"right":{"plane":"xy","origin":"the heads of the rear cover's lower screws (the outline's rear extreme), the hood's top; offset to the cross bolt and the rail's top","offset":{"x":"side_rear_x","y":"top_above_rail"},"points":[[0,-2.643],[0.005,-2.696],[0.019,-2.733],[0.158,-2.745],[0.16,-2.841],[0.172,-2.873],[1.035,-2.866],[1.058,-2.799],[1.067,-2.857],[1.084,-2.873],[1.127,-2.891],[1.252,-2.909],[1.468,-2.911],[2.579,-2.904],[2.717,-2.896],[2.818,-2.876],[2.844,-2.863],[2.866,-2.836],[2.863,-2.413],[2.843,-2.347],[2.855,-2.319],[2.848,-2.273],[2.857,-2.267],[2.936,-2.328],[3.004,-2.364],[3.111,-2.397],[3.346,-2.397],[3.473,-2.354],[3.603,-2.267],[3.709,-2.141],[3.747,-2.067],[3.772,-1.988],[3.785,-1.835],[3.757,-1.675],[3.693,-1.537],[3.632,-1.461],[3.637,-1.456],[3.627,-1.438],[3.525,-1.275],[3.481,-1.228],[3.402,-1.172],[3.323,-1.136],[3.231,-1.116],[2.918,-1.103],[2.811,-1.049],[2.717,-1.032],[2.615,-1.039],[2.526,-1.07],[2.508,-1.039],[2.495,-1.057],[2.419,-1.098],[2.392,-1.084],[2.295,-0.911],[2.254,-0.801],[2.224,-0.666],[2.142,-0.172],[2.129,-0.157],[2.109,-0.011],[2.092,0],[0.562,-0.02],[0.525,-0.042],[0.487,-0.113],[0.474,-0.21],[0.479,-0.274],[0.517,-0.424],[0.53,-0.569],[0.522,-0.692],[0.497,-0.809],[0.443,-0.941],[0.352,-1.028],[0.321,-1.081],[0.303,-1.142],[0.168,-1.275],[0.125,-1.374],[0.064,-1.708],[0.043,-1.907],[0.056,-2.421],[0.022,-2.433],[0.008,-2.457]],"features":{"elevation":[[[0.59,-1.198],[1.415,-1.198],[1.415,-2.024],[0.59,-2.024]]],"elevation_dial":[[[0.814,-1.397],[1.201,-1.397],[1.201,-1.784],[0.814,-1.784]]],"elevation_slot":[[[0.936,-1.417],[1.02,-1.415],[1.053,-1.777],[0.977,-1.782]]],"windage":[[[1.759,-1.514],[2.599,-1.514],[2.599,-2.355],[1.759,-2.355]]],"windage_dial":[[[2.001,-1.698],[2.396,-1.698],[2.396,-2.095],[2.001,-2.095]]],"windage_slot":[[[2.036,-1.973],[2.332,-1.797],[2.37,-1.843],[2.077,-2.024]]],"cap":[[[2.824,-1.463],[3.69,-1.463],[3.69,-2.329],[2.824,-2.329]]],"cap_slot":[[[3.432,-1.527],[3.534,-1.586],[3.081,-2.278],[2.994,-2.233]]],"nut":[[[1.772,-2.515],[2.103,-2.515],[2.103,-2.846],[1.772,-2.846]]],"screw":[[[0.197,-2.253],[0.416,-2.253],[0.416,-2.472],[0.197,-2.472]]],"plate_front":[[[2.337,-1.119],[2.408,-1.26],[2.472,-1.361],[2.536,-1.463],[2.612,-1.565],[2.676,-1.667],[2.714,-1.769],[2.734,-1.871],[2.739,-2.075],[2.734,-2.393],[3.274,-2.393],[3.274,-1.119]]],"base":[[[0.167,-2.457],[2.867,-2.457],[2.867,-2.91],[0.167,-2.91]]]},"scaleRefs":["eotech-exps3.length","eotech-exps3.height"],"inputs":{"eotech-exps3.height":2.9,"eotech-exps3.length":3.8},"tolerance":0.006,"photo":"references/eotech-exps3 41e27975b533 (Primary Arms EXPS3-0TAN_01: the tan sight's right side straight on, on white, 2200 x 1467 (the muzzle to the right))","method":"luminance < 235, opening ×1, closing ×2, largest piece, holes filled; scale from eotech-exps3.length = 3.8 in (x-extent 1486 px → 391.1 px/in) and eotech-exps3.height = 2.9 in (y-extent 1143 px → 394.1 px/in), which agree within 0.8%; mean 392.6 px/in; origin at x min, y max of the outline; Douglas-Peucker at 0.006 in with the extremes kept: 79 points (IoU 0.998 with the full outline); features through the same placement (elevation: the elevation adjuster's round recess in the hood's right flank (a circle: its box); elevation_dial: the slotted dial in it (a circle: its box, on a 4x gridded crop); elevation_slot: the dial's slot as it stands in this photo; windage: the windage adjuster's round recess; windage_dial: the slotted dial in it (a circle: its box, on a 4x gridded crop); windage_slot: the dial's slot as it stands in this photo; cap: the battery cap's knurled disc (a circle: its box; its centre (1753, 930) by a fit of its rim's radius about the turn, 169 px); cap_slot: the cap's coin slot as it stands in this photo, edge to edge of the disc; nut: the adjustment nut on the cross bolt's right end (a circle: its box): its centre is the bolt's axis; screw: the hood's screw on the right flank; plate_front: what is ahead of the hood's right flank below the battery compartment's top: the flank's front edge, picked every 40 rows on a 1.6x gridded crop (the battery cap stands in front of it); base: the base along the rail: its rear foot's rear end to the clamp block's front end) (tools/trace.py)","via":"harvest","note":"The right flank, for where its adjusters, the battery cap and the cross bolt's nut are: the lanyard is in this outline, which no model is cut from."},"top":{"plane":"xz","origin":"the heads of the rear cover's screws, the hood's left flank; offset to the cross bolt and the rail's centre","offset":{"x":"side_rear_x","y":"hood_left_z"},"points":[[0,1.919],[0,1.644],[0.018,1.626],[0.065,1.622],[0.058,0.784],[0.047,0.773],[0.011,0.773],[0,0.762],[0,0.473],[0.058,0.459],[0.061,0.34],[0.166,0.322],[0.163,0.311],[0.137,0.307],[0.116,0.257],[0.116,0.17],[0.126,0.152],[0.152,0.141],[0.09,0.137],[0.072,0.126],[0.065,0.112],[0.065,0.025],[0.076,0.014],[0.126,0.014],[0.134,0.007],[0.871,0.007],[0.878,0],[2.735,0.007],[2.753,0.033],[2.753,0.098],[2.742,0.116],[2.692,0.116],[2.681,0.126],[2.681,0.177],[2.699,0.181],[2.717,0.199],[2.724,0.235],[2.75,0.275],[2.901,0.188],[2.981,0.159],[3.031,0.159],[3.039,0.152],[3.667,0.152],[3.674,0.159],[3.776,0.159],[3.801,0.191],[3.808,1.832],[3.815,1.839],[3.808,2.02],[3.797,2.031],[3.667,2.031],[3.653,2.052],[3.635,2.056],[3.653,2.074],[3.689,2.074],[3.7,2.085],[3.7,2.265],[3.689,2.276],[3.674,2.283],[3.306,2.283],[3.302,2.229],[3.241,2.218],[3.237,2.273],[3.226,2.283],[2.952,2.283],[2.945,2.291],[2.858,2.291],[2.833,2.265],[2.833,2.085],[2.883,2.078],[2.872,2.059],[2.829,2.052],[2.663,2.059],[2.656,2.067],[2.612,2.067],[2.601,2.078],[2.605,2.088],[2.627,2.096],[2.728,2.103],[2.76,2.121],[2.768,2.2],[2.75,2.24],[2.294,2.24],[2.287,2.247],[2.121,2.247],[2.092,2.262],[1.832,2.262],[1.803,2.247],[0.09,2.247],[0.072,2.229],[0.072,2.128],[0.083,2.11],[0.159,2.078],[0.152,1.962],[0.166,1.947],[0.033,1.937]],"features":{"cap":[[[2.843,2.049],[3.696,2.049],[3.696,2.294],[2.843,2.294]]],"hood_top":[[[0.524,0.199],[2.244,0.199],[2.244,2.171],[0.524,2.171]]]},"scaleRefs":["eotech-exps3.length","eotech-exps3.width"],"inputs":{"eotech-exps3.length":3.8,"eotech-exps3.width":2.3},"tolerance":0.006,"photo":"references/eotech-exps3 48bb645b068b (EOTECH exps3_to: the black sight from above, 700 x 700 with its own alpha (the muzzle to the right, the battery cap toward the bottom: the sight's right))","method":"alpha > 0.5, largest piece, holes filled; rotated +180.0° as declared; scale from eotech-exps3.length = 3.8 in (x-extent 528 px → 138.9 px/in) and eotech-exps3.width = 2.3 in (y-extent 317 px → 137.8 px/in), which agree within 0.8%; mean 138.4 px/in; origin at x min, y min of the outline; Douglas-Peucker at 0.006 in with the extremes kept: 96 points (IoU 0.999 with the full outline); features through the same placement (cap: the battery cap, from the battery compartment's right end to its knurled face; hood_top: the hood's top between its two bends, seen from above) (tools/trace.py)","via":"harvest"},"front":{"plane":"zy","origin":"the hood's left flank, the hood's top; offset to the rail's centre and the rail's top","offset":{"x":"hood_left_z","y":"top_above_rail"},"points":[[0,-2.229],[0.007,-2.579],[0.012,-2.6],[0.04,-2.616],[0.038,-2.886],[0.057,-2.908],[0.116,-2.913],[0.171,-2.898],[0.211,-2.757],[0.233,-2.742],[0.32,-2.733],[0.349,-2.816],[0.409,-2.862],[0.437,-2.869],[0.634,-2.869],[0.667,-2.859],[0.69,-2.837],[0.71,-2.761],[0.808,-2.761],[0.854,-2.743],[0.854,-2.635],[0.864,-2.599],[0.907,-2.589],[1.176,-2.578],[1.514,-2.594],[1.561,-2.627],[1.614,-2.682],[1.656,-2.745],[1.677,-2.83],[1.699,-2.855],[1.756,-2.866],[1.981,-2.862],[2.028,-2.84],[2.059,-2.806],[2.076,-2.769],[2.09,-2.68],[2.113,-2.645],[2.185,-2.594],[2.229,-2.601],[2.245,-2.593],[2.252,-2.466],[2.242,-2.056],[2.186,-1.226],[2.144,-0.841],[2.116,-0.393],[2.078,-0.264],[2.036,-0.194],[1.969,-0.124],[1.915,-0.087],[1.819,-0.047],[1.659,-0.023],[1.432,-0.005],[1.066,0],[0.728,-0.021],[0.503,-0.056],[0.43,-0.087],[0.367,-0.129],[0.298,-0.201],[0.263,-0.257],[0.235,-0.327],[0.218,-0.416],[0.211,-0.754],[0.197,-0.939],[0.181,-0.972],[0.07,-1.075],[0.033,-1.146],[0.021,-1.2],[0.002,-1.817]],"features":{"hood_gap":[[[0.225,-1.097],[0.235,-1.061],[0.347,-0.932],[0.371,-0.871],[0.385,-0.374],[0.403,-0.313],[0.434,-0.262],[0.527,-0.181],[0.618,-0.145],[0.921,-0.12],[0.925,-0.11],[0.963,-0.12],[0.986,-0.108],[1.005,-0.117],[1.031,-0.106],[1.387,-0.108],[1.394,-0.117],[1.434,-0.113],[1.469,-0.127],[1.507,-0.12],[1.526,-0.129],[1.549,-0.124],[1.678,-0.138],[1.749,-0.157],[1.838,-0.213],[1.893,-0.28],[1.928,-0.386],[1.954,-0.892],[1.946,-0.934],[1.937,-0.925],[1.926,-0.803],[1.909,-0.487],[1.893,-0.428],[1.853,-0.346],[1.858,-0.341],[1.791,-0.274],[1.746,-0.244],[1.678,-0.216],[1.57,-0.199],[1.355,-0.185],[1.094,-0.183],[0.7,-0.206],[0.595,-0.246],[0.529,-0.293],[0.488,-0.339],[0.45,-0.405],[0.425,-0.482],[0.422,-0.62],[0.394,-1.017],[0.382,-1.066],[0.389,-1.073],[0.385,-1.127],[0.32,-1.135],[0.299,-1.149],[0.233,-1.149]]],"latch":[[[0.041,-2.605],[0.196,-2.605],[0.196,-2.912],[0.041,-2.912]]],"cover":[[[0.341,-1.392],[1.915,-1.392],[1.915,-2.577],[0.341,-2.577]]],"cover_screws":[[[0.529,-1.479],[0.67,-1.479],[0.67,-1.62],[0.529,-1.62]],[[1.678,-1.465],[1.819,-1.465],[1.819,-1.606],[1.678,-1.606]],[[0.508,-2.581],[0.649,-2.581],[0.649,-2.722],[0.508,-2.722]],[[1.692,-2.581],[1.833,-2.581],[1.833,-2.722],[1.692,-2.722]]]},"scaleRefs":["eotech-exps3.height","eotech-exps3.hood_width"],"inputs":{"eotech-exps3.height":2.9,"eotech-exps3.hood_width":2.262},"tolerance":0.006,"photo":"references/eotech-exps3 4bbcf783f58b (Primary Arms EXPS3-0_03: the black sight from behind, straight on, on white, 2200 x 1466 (the sight's right to the right))","method":"luminance < 235, closing ×2, largest piece, holes filled; scale from eotech-exps3.height = 2.9 in (y-extent 1242 px → 428.3 px/in) and eotech-exps3.hood_width = 2.262 in (x-extent 960 px → 424.4 px/in), which agree within 0.9%; mean 426.3 px/in; origin at x min, y max of the outline; Douglas-Peucker at 0.006 in with the extremes kept: 68 points (IoU 0.997 with the full outline); features through the same placement (hood_gap: the gap between the hood and the window's frame, where the backdrop shows: flood-filled from a pixel in it; latch: the quick-detach lever's latch, hanging lowest at the far left: the lever seen from its rear end (rows 1300 and 1320 show the backdrop between it and the rear cover's left foot, columns 698 to 760); cover: the rear cover plate, to the roof of the rail's channel; cover_screws: the rear cover's four screws (circles: their boxes)) (tools/trace.py)","via":"harvest","note":"From behind, looking forward. The quick-detach lever's latch hangs lowest, on the left; the notch in the rear cover's lower edge is where the rail lies."}},"gaps":[{"what":"The reticle's height over the rail, as EOTECH states it","need":"No page or document on file states one (only \"lower 1/3 co-witness\" and \"7mm raised base\"): the window's centre is 1.86 in above the rail's top by the photos, the rail's top taken at the roof of the notch in the current rear cover, which the cross bolt's axis agrees with within a slot's depth; no view on file has the sight on a rail, and at 1.86 in an AR's own sights come up at the window's lower edge. A dimensioned drawing, or a photo of the sight on a rail from straight behind or straight from the side with the rail's slots in frame, would close it"},{"what":"What the tan sight's lever and its housing are made of and finished in, and which of two looks the lever has","need":"No page on file names either. Primary Arms' photos (an older sight) have the lever an olive gold and its latch a bare grey; EOTECH's current pictures have both a redder bronze, in a light of their own. A page of EOTECH's that names the finishes, or a large photo of a current tan sight's left side on white, would settle it; the plate of the same metal round the adjustment nut wants an outline traced on the right side view before it is drawn"},{"what":"The cross bolt's own size, and how far the jaws hook under the rail","need":"The manual's Figure 1 draws the base from below, undimensioned; the rear cover's notch in the view from behind is the only section of the channel on file. A view of the base from below, or from the front with the lever open, would give both"}]},"eotech-g33":{"id":"eotech-g33","name":"G33 Magnifier, STS Mount","manufacturer":"EOTECH","sku":"G33.STS","url":"https://www.eotechinc.com/products/eotech-magnifier-g33","category":"magnifier","description":"A 3X magnifier on EOTECH's Switch-to-Side (STS) quick-detach mount, with its 7 mm riser fitted, as EOTECH pictures it (lower third co-witness), or without it (absolute co-witness): the lever on the rifle's left, the hinge on its right. In line behind the sight, or swung aside to the right.","weight":"eotech-g33.weight","fitments":{"label":"Height","default":"riser","setup":true,"says":"EOTECH: \"The 7mm riser (included) may be required to align the magnifier optical axis with the sight. HWS models with side buttons or quick-detach levers require the use of the riser. All other HWS models, the riser should not be used.\"","options":{"riser":{"label":"With the riser","params":{},"source":"https://img.trex-arms.com/wp/uploads/2026/03/eotech-g-series-magnifier-user-manual-2022-01.pdf"},"no_riser":{"label":"Without the riser","params":{},"anchors":{"optical_axis":{"origin":[0,"{.optical_axis_above_rail_no_spacer}",0],"note":"Without the riser."},"eyepiece":{"origin":["-{.eyepiece_rear_behind_base}","{.optical_axis_above_rail_no_spacer}",0],"note":"The diopter ring's rear face, on the axis, without the riser."}},"components":{"inline":"inline_no_riser","aside":"aside_no_riser"},"weight":"eotech-g33.weight","source":"https://img.trex-arms.com/wp/uploads/2026/03/eotech-g-series-magnifier-user-manual-2022-01.pdf"}}},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":[0,0,0]},"optical_axis":{"origin":[0,"{.optical_axis_above_rail_spacer}",0],"note":"The 7 mm riser fitted, as EOTECH's pictures have it: 47 mm by a reviewer's figure. Without the riser it is 40 mm (optical_axis_above_rail_no_spacer): the part's fitments."},"eyepiece":{"origin":["-{.eyepiece_rear_behind_base}","{.optical_axis_above_rail_spacer}",0],"note":"The diopter ring's rear face, on the axis. EOTECH gives the eye relief behind it: 2.2 in (55.9 mm)."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":"={.clamp_length} / 2","clamp_front":"={.clamp_length} / 2"},"flips":false,"note":"The STS mount's clamp, 1.4 in long about the frame's origin. EOTECH's page: \"Mount 1\\\" Weaver or MIL-STD-1913 rail\", \"Ambidextrous and equipped with a locking, adjustable, quick-detach lever system allowing for immediate attachment or removal.\" Its manual, of where on the rail: \"Place the mount in the desired position behind the HWS. Once the mount is located in the desired position, push the magnifier forward until the cross bolt of the magnifier is set into the slot located on the mount. Close the quick detach lever.\""},"sight_line":{"type":"optic.sight_line","role":"magnifier","params":{"magnification":"1x"},"flips":false,"note":"What it goes behind. EOTECH's manual: \"The G-Series magnifiers are designed to be used behind an EOTECH Holographic Weapon Sight (HWS). The magnifier can be mounted directly behind the HWS.\" Its page: \"Compatible with all EOTECH HWS® models\". T.REX ARMS, asked whether it should be butted up to the optic: \"For optimal results, yes. It can be backed off some and you still have a good sight picture.\""}},"eye":{"anchor":"eyepiece","relief":["{.eye_relief}"],"note":"EOTECH: Eye Relief 2.2\" (55.9 mm)."},"folds":{"up":"inline","folded":"aside","note":"EOTECH's manual: \"To switch the magnifier to the side, simply push the optic to the right or left, depending on how it is mounted. To close the mount, push the magnifier back into its original position until a hard stop is achieved.\" Which side is the owner's to set, since the magnifier comes off its mount: \"Position the mount on the optic mount interface (or riser) so it opens either to the left or right (based on preference).\" Its two manuals disagree on what is usual: the 2022 one, \"Typically, right-handed shooters prefer the mount to switch to the right, and left-handed shooters to the left\"; the 2015 one, \"Typically, right handed shooters prefer the mount to switch to the left, and left handed shooters to the right.\" Drawn as EOTECH's own pictures have it, to the rifle's right.","says":{"field":"Magnifier","up":"In line","folded":"Aside","toUp":"swing it in line","toFolded":"swing it aside"}},"materials":{"body":{"label":"Armoured body","finish":"rubber","recolorable":false,"color":"placeholder-polymer-black","options":{"black":{"label":"Black","finish":"rubber","color":"placeholder-polymer-black","sku":"G33.STS","source":"https://www.eotechinc.com/products/eotech-magnifier-g33"},"tan":{"label":"Tan","finish":"rubber","color":"eotech-g33-tan-rubber","sku":"G33.STSTAN","source":"https://www.eotechinc.com/products/eotech-magnifier-g33"}},"default":"black","note":"The two colours EOTECH sells the kit in: its page lists \"Black / STS Mount\" (G33.STS) and \"Tan / STS Mount\" (G33.STSTAN). The armour round the magnifier's middle is rubber (EOTECH's 2015 sheet, of the magnifier: \"Finish: Non reflective / Rubber coated\"): a charcoal on the black kit, a khaki on the tan one, yellower than the tube it is on (EOTECH's own two pictures of the tan kit, references/eotech-g33 3145815589cd and d40b117a7965, the same picture series). Tan is matched to its flat in the first; black is the placeholder. The maker's mark moulded in it isn't drawn."},"tube":{"label":"Objective tube, diopter ring and knobs","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","follows":{"slot":"body","options":{"tan":{"finish":"anodized_matte","color":"eotech-g33-tan"}}},"note":"What of the magnifier is bare of the armour: the objective tube with the foot under it, the diopter ring, the two adjustment knobs. Black on the black kit; on the tan one a smooth tan with a soft sheen, browner than the armour (the tube #917a67 beside an armour of #967f62 in EOTECH's left side view of the tan kit; the diopter ring reads as the tube, #90775a, the knob darker in its own shadow). No page on file states what the bare metal's finish is, on either kit: drawn as matte anodize by how it takes the light in EOTECH's pictures. The white marks on the tube, the letters on the knobs and the black screw in the horizontal knob's middle aren't drawn."},"mount":{"label":"STS mount and riser","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","note":"EOTECH's 2015 sheet, of the mount: \"Color/Finish: Non reflective black with hard coat finish.\" Black on the tan kit too, riser, lever and all, by EOTECH's pictures of it (EOTECH-G33-Tan-1.webp, and its right side view as Arisaka Defense serves it, references/eotech-g33 0a42235d2685)."},"hardware":{"label":"Hinge barrel and clamp nut","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The round barrel between the hinge's two knuckles and the slotted nut on the clamp's right face: a dark grey steel beside the mount's black on both kits (EOTECH's right side views of the black and the tan one: the barrel reads #3f3f40 beside a knuckle of #343436, both under the light from above). No page names the metal or its finish; a round bar has no flat to match a colour on, so it is the dark steel the other parts' screws are."},"pin":{"label":"Hinge pin","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"The hinge pin's two ends, bright in the knuckles' black on both kits (EOTECH's view from behind, g33sts_blk_rv_closed: a turned, bare steel face). No page names the metal: drawn as bright stainless by that picture."},"lens":{"label":"Lenses","finish":"glass","recolorable":false,"color":"glass-clear"}},"components":{"body":{"label":"Armoured body","material":"body"},"tube":{"label":"Objective tube, diopter ring and knobs","material":"tube"},"mount":{"label":"STS mount and riser","material":"mount"},"hardware":{"label":"Hinge barrel and clamp nut","material":"hardware"},"pin":{"label":"Hinge pin","material":"pin"},"lens":{"label":"Lenses","material":"lens"}},"geometry":{"components":{"inline":"eotech-g33.inline.glb","aside":"eotech-g33.aside.glb","inline_no_riser":"eotech-g33.inline_no_riser.glb","aside_no_riser":"eotech-g33.aside_no_riser.glb"},"approximations":["The magnifier is turned about its optical axis at the top edge of EOTECH's left side view: the objective tube and the diopter ring round, the armoured body between them eight-sided with a flat above, below and on each side and its corners turned round. The side view has the body's side flat 0.34 in to each side of the axis, which is what a regular eight-sided body of its height has (0.33), and the rear view shows the same; how round the corners are isn't measured. The body's underside is drawn as far below the axis as its top is above (0.805 in; the side view has it 0.822).","Not drawn on the body: the armour's panels (one on each face of its rear half, the EOTECH mark in the one on each side), the kidney-shaped port low on its left, the parting line along it, and every marking. Whether the panels stand out or in, and by how much, isn't read: a side view says where a feature is and not which way it goes, and the side view's outline moves by no more than a few thousandths of an inch over the one on top.","The diopter ring has its 18 flutes, counted where they run out at its rear rim in the rear view (the one view of the ring's whole turn), each 0.028 in deep and 11 degrees of the turn by the same view, cut straight along the ring; how they end toward the body isn't read, and the ring is drawn as it stood, since it turns.","The two adjustment knobs are the vertical one's silhouette in the side view turned about its axis, with eight lugs each in two tiers (counted on the horizontal knob, seen face on in the right side view, unwrapped about its middle) and the notches between them cut 0.036 in deep. The horizontal one, on the rifle's right, is taken to be the same knob (the two side views show them alike) on the optical axis's level, standing 1.11 in out from the middle by the rear view. The cross slots and the socket in each knob's face aren't drawn.","The pieces are told apart, for their colours, where EOTECH's pictures have them (2026-10-06): the armour is the housing's eight-sided middle, end to end; ahead of it the objective tube with its foot, behind it the diopter ring, and the two knobs are bare of it. The part of the foot that lies under the armour is drawn as the armour's (in the pictures the armour comes down to the riser there). The hinge's barrel and the clamp's nut are a steel of their own and the pin's two ends bright; the lever is drawn as the mount's black.","The magnifier's foot is a plain block under the objective tube as long and as wide as the riser; the riser and the mount's top plate are plain blocks (the riser's slots, the plate's two rails, the screws and their holes aren't drawn). The riser is drawn fitted, as in every picture of EOTECH's.","Without the riser (the build's choice, D95) the magnifier is drawn on the mount's top plate, lower by as much as the ledger has its axis lower (EOTECH's 7 mm), its foot reaching down by what the side view's riser band is over 7 mm (a hundredth of an inch) to stand off the plate as the riser does: four models, in line and aside, each with the riser and without it. The screws are not drawn, so the shorter pair EOTECH gives for that way isn't either.","The mount is two pieces a hinge joins. What stays on the rail: the clamp as a block with the rail's own head in section (MIL-STD-1913's, since 2026-10-12) cut out of its underside down to the lower gauge line, and plain jaws the rail's width (0.835 in) apart below it; the quick-detach lever as the side view's outline at 0.2 in thick along the clamp's left, its tail to the rear (its locking button and its pivot aren't drawn); on the right the two hinge knuckles on their walls, the pin's ends, and the clamp's slotted nut as a plain disc. What swings: a round barrel between the knuckles, an arm from it to the top plate, the plate, the riser and the magnifier.","Swung aside it is turned 93.5 degrees about that hinge, over to the rifle's right: no page states the angle, and it is the turn between EOTECH's two rear views, in line and swung aside (good to about 3 degrees). The magnifier then lies beside the rail with its eyepiece still to the rear, the knob that was on top pointing right. Where it comes to rest follows from the hinge's place, which is read on a close rear view and a side view: good to about 0.05 in.","Which side is which: the lever is on the rifle's left, the hinge and the knob marked R on its right, so the magnifier swings to the right. EOTECH's own side and rear views all have it so. The mount can be fitted to open to the left instead (its manual: \"so it opens either to the left or right (based on preference)\"); the model has the one arrangement.","Across the rifle the model is 2.11 in from the lever's face to the horizontal knob's, against EOTECH's 2.2: each face is where the rear view has it at the scale the mount's published height gives there (316 px/in), a close view in which a reading is good to 0.05 in.","Lenses at the end faces: the objective's at its clear aperture (the exit pupil times the magnification, 22.8 mm), the eyepiece's at the glass that shows in the rear view (0.95 in, good to 0.06). Their recess behind the retainers isn't sourced."],"ledger":["eotech-g33.length","eotech-g33.width","eotech-g33.height","eotech-g33.optical_axis_above_rail_spacer","eotech-g33.eye_relief","eotech-g33.eyepiece_rear_behind_base","eotech-g33.riser_thickness","eotech-g33.sts_mount_length","eotech-g33.sts_mount_height","eotech-g33.flip_angle","eotech-g33.hinge_axis_above_clamp_bottom","eotech-g33.hinge_axis_right_of_centre","eotech-g33.hinge_knuckle_d","eotech-g33.hinge_barrel_d","eotech-g33.clamp_below_rail","eotech-g33.knob_lugs","eotech-g33.diopter_flutes"]},"profiles":{"side":{"plane":"xy","origin":"the middle of the mount's top plate (x over its rows), the clamp's bottom; offset to the rail's top","offset":{"y":"clamp_bottom_y"},"points":[[-3.176,2.432],[-3.176,1.993],[-3.163,1.714],[-3.142,1.596],[-3.099,1.546],[-2.779,1.539],[-2.739,1.579],[-2.726,1.609],[-2.699,1.614],[-2.667,1.455],[-2.632,1.43],[-2.542,1.43],[-2.404,1.413],[-1.611,1.396],[-1.434,1.405],[-1.141,1.384],[-0.801,1.385],[-0.801,1.111],[-0.824,1.107],[-0.832,1.092],[-0.832,0.878],[-0.812,0.865],[-0.677,0.861],[-0.68,0.6],[-0.698,0.569],[-1.369,0.555],[-1.382,0.534],[-1.385,0.413],[-1.385,0.103],[-1.374,0.087],[-1.083,0.082],[-0.705,0.097],[-0.7,0.01],[-0.15,0],[0,0.002],[0.603,0],[0.683,0.002],[0.694,0.011],[0.699,0.571],[0.689,0.583],[0.689,0.859],[0.824,0.86],[0.832,0.869],[0.832,1.101],[0.811,1.121],[0.82,2.386],[0.811,2.8],[-0.281,2.806],[-0.304,2.928],[-0.383,3.007],[-0.437,3.02],[-0.423,3.037],[-0.42,3.071],[-0.452,3.103],[-0.452,3.139],[-0.42,3.163],[-0.42,3.207],[-0.485,3.264],[-0.516,3.269],[-0.552,3.312],[-0.601,3.349],[-0.647,3.358],[-0.657,3.327],[-0.703,3.361],[-0.841,3.361],[-0.884,3.322],[-0.889,3.358],[-0.926,3.358],[-0.991,3.312],[-1.03,3.271],[-1.052,3.266],[-1.107,3.223],[-1.121,3.207],[-1.121,3.166],[-1.087,3.142],[-1.087,3.127],[-1.094,3.096],[-1.121,3.076],[-1.112,3.024],[-1.531,3.036],[-2.622,3.024],[-2.653,3.01],[-2.667,2.987],[-2.695,2.84],[-2.724,2.842],[-2.749,2.885],[-2.782,2.913],[-3.051,2.915],[-3.094,2.908],[-3.134,2.868],[-3.154,2.793]],"scaleRefs":["eotech-g33.length","eotech-g33.sts_mount_length"],"inputs":{"eotech-g33.length":4.015748031496063,"eotech-g33.sts_mount_length":1.6614173228346458},"tolerance":0.006,"photo":"references/eotech-g33 27d853fe5719 (EOTECH's left side view, in line, the 7 mm riser fitted (the objective at the picture's left))","method":"alpha > 0.5, largest piece, holes filled; scale from eotech-g33.length = 4.01575 in (x-extent 1654 px → 411.9 px/in) and eotech-g33.sts_mount_length = 1.66142 in (median width over 0.69–0.73 of the height from the top, 687–687 px 687 px → 413.5 px/in), which agree within 0.4%; mean 412.7 px/in; origin at x center, y min of the outline (x over 0.69–0.73 of the height from the top); Douglas-Peucker at 0.006 in with the extremes kept: 91 points (IoU 0.997 with the full outline); checks: height 3.361 ± 0.010 in vs eotech-g33.height 3.354 ± 0.02 (conflict): agrees; −x_min 3.176 ± 0.007 in vs eotech-g33.eyepiece_rear_behind_base 3.168 ± 0.02 (provisional): agrees (tools/trace.py)","via":"harvest","note":"The outline encloses everything seen from the left: the housing, the knob on top, the riser, the mount and its lever. The lever is on this side; the hinge, on the far side, is behind the mount here."}},"gaps":[{"what":"The optical axis's height over the rail from EOTECH itself. Its manual says only \"an absolute co-witness or lower-third co-witness height\"; the 47 mm with the riser (40 mm without) is one reviewer's, which EOTECH's pictures bear out within 1.3 mm.","need":"EOTECH's own centreline figure for the G33 on the STS mount, or a second independent reading of it."},{"what":"The mount set to open to the left (EOTECH: \"Position the mount on the optic mount interface (or riser) so it opens either to the left or right (based on preference).\"): the model has the one arrangement EOTECH pictures, opening to the right.","need":"A decision to offer it as a choice: drawn mirrored about the rail's middle, as EOTECH's manual says it is set up."},{"what":"The tan kit (G33.STSTAN): the magnifier tan, the mount black.","need":"A colour preset matched to EOTECH's tan (its EOTECH-G33-Tan-1.webp and T.REX's photos of it are on file; T.REX's read olive-grey on the body and tan on the tubes)."},{"what":"What the 2022 manual's 4.4 in (113 mm) length spans. EOTECH's page and catalogue say 4 in (102 mm), and its side views agree with the mount's published 1.66 in only at 4 in.","need":"A reviewer's rule on the part, or EOTECH's word."},{"what":"A view square across the magnifier's width. The rear views are close ones (their scale changes by 5% and more with depth), so the housing's width, the knob on its right and the hinge's place across the rifle are each good to about 0.05 in.","need":"A straight view from above or below, or a rear view from further off."}]},"eotech-g45":{"id":"eotech-g45","name":"G45 Magnifier, STS Mount","manufacturer":"EOTECH","sku":"G45.STS","url":"https://www.eotechinc.com/products/eotech-magnifier-g45","category":"magnifier","description":"A 5X magnifier on EOTECH's Switch-to-Side (STS) quick-detach mount, with its 7 mm riser fitted, as EOTECH pictures it (lower third co-witness), or without it (absolute co-witness): the lever on the rifle's left, the hinge on its right. In line behind the sight, or swung aside to the right.","weight":"eotech-g45.weight","fitments":{"label":"Height","default":"riser","setup":true,"says":"EOTECH: \"The 7mm riser (included) may be required to align the magnifier optical axis with the sight. HWS models with side buttons or quick-detach levers require the use of the riser. All other HWS models, the riser should not be used.\"","options":{"riser":{"label":"With the riser","params":{},"source":"https://img.trex-arms.com/wp/uploads/2026/03/eotech-g-series-magnifier-user-manual-2022-01.pdf"},"no_riser":{"label":"Without the riser","params":{},"anchors":{"optical_axis":{"origin":[0,"{.optical_axis_above_rail_no_spacer}",0],"note":"Without the riser."},"eyepiece":{"origin":["-{.eyepiece_rear_behind_base}","{.optical_axis_above_rail_no_spacer}",0],"note":"The diopter ring's rear face, on the axis, without the riser."}},"components":{"inline":"inline_no_riser","aside":"aside_no_riser"},"weight":"eotech-g45.weight","source":"https://img.trex-arms.com/wp/uploads/2026/03/eotech-g-series-magnifier-user-manual-2022-01.pdf"}}},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":[0,0,0]},"optical_axis":{"origin":[0,"{.optical_axis_above_rail_spacer}",0],"note":"The 7 mm riser fitted, as EOTECH's own picture has it: the diopter ring's middle in that picture, over the rail's top where the same mount's clamp puts it (1.83 in). No page states the height. Without the riser it is lower by the riser (optical_axis_above_rail_no_spacer): the part's fitments."},"eyepiece":{"origin":["-{.eyepiece_rear_behind_base}","{.optical_axis_above_rail_spacer}",0],"note":"The diopter ring's rear face, on the axis. EOTECH gives the eye relief behind it: 2.6 in (66 mm)."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":"={.clamp_length} / 2","clamp_front":"={.clamp_length} / 2"},"flips":false,"note":"The STS mount's clamp, 1.4 in long about the frame's origin. EOTECH's page: \"Mount 1\\\" Weaver or MIL-STD-1913 rail\"; its catalogue: \"Adjustable, locking, quick-detach throw lever\". Its manual, of where on the rail: \"Place the mount in the desired position behind the HWS. Once the mount is located in the desired position, push the magnifier forward until the cross bolt of the magnifier is set into the slot located on the mount. Close the quick detach lever.\""},"sight_line":{"type":"optic.sight_line","role":"magnifier","params":{"magnification":"1x"},"flips":false,"note":"What it goes behind. EOTECH's manual: \"The G-Series magnifiers are designed to be used behind an EOTECH Holographic Weapon Sight (HWS). The magnifier can be mounted directly behind the HWS.\" Its page: \"the G45 ™ is compatible with all EOTECH HWS ® models\". Which of them want the riser, by the same manual: \"HWS models with side buttons or quick-detach levers require the use of the riser. All other HWS models, the riser should not be used.\""}},"eye":{"anchor":"eyepiece","relief":["{.eye_relief}"],"note":"EOTECH: Eye Relief 2.6\" (66 mm)."},"folds":{"up":"inline","folded":"aside","note":"EOTECH's manual: \"To switch the magnifier to the side, simply push the optic to the right or left, depending on how it is mounted. To close the mount, push the magnifier back into its original position until a hard stop is achieved.\" Which side is the owner's to set, since the magnifier doesn't come fixed to its mount: \"Position the mount on the optic mount interface (or riser) so it opens either to the left or right (based on preference).\" And of what is usual: \"Typically, right-handed shooters prefer the mount to switch to the right, and left-handed shooters to the left.\" Drawn as EOTECH's own pictures have it, to the rifle's right.","says":{"field":"Magnifier","up":"In line","folded":"Aside","toUp":"swing it in line","toFolded":"swing it aside"}},"materials":{"body":{"label":"Armoured body","finish":"rubber","recolorable":false,"color":"placeholder-polymer-black","options":{"black":{"label":"Black","finish":"rubber","color":"placeholder-polymer-black","sku":"G45.STS","source":"https://www.eotechinc.com/products/eotech-magnifier-g45"},"tan":{"label":"Tan","finish":"rubber","color":"eotech-g45-tan-rubber","sku":"G45.STSTAN","source":"https://www.eotechinc.com/products/eotech-magnifier-g45"}},"default":"black","note":"The two colours EOTECH sells the kit in: its page lists \"Black / STS Mount\" (G45.STS) and \"Tan / STS Mount\" (G45.STSTAN); its catalogue writes the second \"G45.STS TAN\". The armour is the collar with its pads and the eight-sided body behind it. No page names what it is made of on the G45: sellers say only \"Finish Matte\" (KYGunCo) and \"FINISH/COLOR Matte Tan\" (Midwest Gun Works). Drawn as the rubber EOTECH's 2015 sheet names on the G33 (\"Finish: Non reflective / Rubber coated\"), which every picture has it look like: a moulded skin with a parting line along each side, speckled where the tube is smooth. A charcoal on the black kit (the placeholder); on the tan one a brown khaki, darker than the tube it is on (EOTECH's own left side view of the tan kit, references/eotech-g45 6fece6de9f55: its side flat #6f5841 and #755d45 beside a tube of #897563), matched to that flat. The maker's mark isn't on the armour here (it is on the tube) and isn't drawn."},"tube":{"label":"Objective tube, diopter ring and knobs","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","follows":{"slot":"body","options":{"tan":{"finish":"anodized_matte","color":"eotech-g33-tan"}}},"note":"What of the magnifier is bare of the armour: the objective tube with the foot under it, the neck and the diopter ring, the two adjustment knobs. Black on the black kit; on the tan one a smooth tan with a soft sheen, lighter and greyer than the armour: the tube reads #897563 above its mark and #876f5d below it in EOTECH's left side view of the tan kit, within nine levels a channel of the G33's tube in EOTECH's picture of that kit (#89715a, #826b56), so it is the preset matched there. The diopter ring (#6b5542) and the knob (#645242) read darker in that picture, in less light; T.REX ARMS' and Midwest Gun Works' photos of tan ones have them the tube's tan or a little browner: drawn as the tube's. No page on file states what the bare metal's finish is: drawn as matte anodize by how it takes the light. The white marks on the tube, the letters on the knobs and the black screw in each knob's middle aren't drawn."},"mount":{"label":"STS mount and riser","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","note":"EOTECH's 2015 sheet, of this mount: \"Color/Finish: Non reflective black with hard coat finish.\" Black on the tan kit too, riser, lever and all, by EOTECH's own picture of it (EOTECH-G45-Tan-1: the riser #333335, the top plate #29282b, the lever #2b2b2e) and T.REX ARMS' (9914)."},"hardware":{"label":"Hinge barrel and clamp nut","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The round barrel between the hinge's two knuckles and the slotted nut on the clamp's right face: a dark steel beside the mount's black on both kits (Primary Arms' G45.STS_01 of the black kit, T.REX ARMS' 9914 of the tan). No page names the metal or its finish; a round bar has no flat to match a colour on, so it is the dark steel the other parts' screws are."},"pin":{"label":"Hinge pin","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"The hinge pin's two ends, bright in the knuckles' black on both kits (EOTECH's own views from ahead, EOTECH-G45-Black-2 and -3; T.REX ARMS' 9914 of the tan kit). No page names the metal: drawn as bright stainless by those pictures."},"lens":{"label":"Lenses","finish":"glass","recolorable":false,"color":"glass-clear"}},"components":{"body":{"label":"Armoured body","material":"body"},"tube":{"label":"Objective tube, diopter ring and knobs","material":"tube"},"mount":{"label":"STS mount and riser","material":"mount"},"hardware":{"label":"Hinge barrel and clamp nut","material":"hardware"},"pin":{"label":"Hinge pin","material":"pin"},"lens":{"label":"Lenses","material":"lens"}},"geometry":{"components":{"inline":"eotech-g45.inline.glb","aside":"eotech-g45.aside.glb","inline_no_riser":"eotech-g45.inline_no_riser.glb","aside_no_riser":"eotech-g45.aside_no_riser.glb"},"approximations":["The objective tube, the neck and the diopter ring are turned about the optical axis at the top edge of EOTECH's left side view. The axis is the diopter ring's middle in that view; the objective tube is taken to be about the same axis (its top edge alone shows, and gives the ring's diameter to the pixel).","The armour stands 0.026 in higher than the tube and the ring: its top is 0.872 in above the axis and its underside 0.820 below on EOTECH's view, and the two sellers' side views read the same within 0.008. It is drawn about a middle that much above the axis.","The armour's front end is a collar an inch long: round, with seven raised pads, one on top in line with the knob, three down each side (at the axis's height and 45 degrees above and below it), none underneath where the foot is. The pads stand 0.027 in out of the collar, read where the top one meets the side view's outline; each is 0.89 in long, the six down the sides 34 degrees of the turn wide and the one on top 44, as EOTECH's two left side views read them. The two at the axis's height are drawn on the optical axis's level, where the armour's parting line runs through them (0.04 in under the diopter ring's middle on the black kit's picture, on it on the tan's). Each is a rectangle with its corners rounded by an amount that isn't measured, its face the collar's own round.","The four pads above and below the axis's height have a panel sunk in their faces, 0.79 in long and 22 degrees of the turn wide by the side view, a rim left round it. Its depth is read no better than within a factor of two (a side view shows the panel's walls only as bands) and is drawn as the pad's own relief, so that the panel's floor is the collar's skin. Not drawn: the armour's parting line, the serial label underneath.","Behind the collar the armour is eight-sided: a flat on top, one underneath and one down each side, with a facet between each two, its corners turned round and its two ends following the side view's outline. The side flat's two edges are read on the side view (0.334 in above the axis, 0.373 below). Across the rifle nothing is read, no view square across it being on file: the facets are taken at 45 degrees and the top flat as wide as the side flats are tall (0.707 in, which the knob on it just fits), which makes the body 1.78 in wide for a height of 1.69. How round the corners are isn't measured.","The diopter ring is drawn with 20 flutes, 8 degrees of the turn each: not a count of the whole turn (no view from behind is on file) but the flutes' spacing on two side views, 17.5 to 18 degrees, which leaves 19 or 21 possible. Their depth isn't read on this ring at all: it is the G33's ring's (0.028 in), so that they can be drawn. The ring is drawn as it stood in EOTECH's picture, since it turns.","The two adjustment knobs are the vertical one's silhouette in the side view turned about its axis, with eight lugs each in two tiers (counted on the knob marked R, seen face on in Rifle Supply's right side view, unwrapped about its middle) and the notches between them cut 0.035 in deep. The horizontal one, on the rifle's right, is taken to be the same knob (the side views show them alike, at the same place along the housing) on the optical axis's level, where the armour's parting line passes through its middle, standing as far out of the body's side flat as the other does out of its top. The slot and the socket in each knob's face, and the recess in the armour round each, aren't drawn.","The pieces are told apart, for their colours, where the pictures of both kits have them: the armour is the collar and the eight-sided body; ahead of it the objective tube with its foot, behind it the neck and the diopter ring, and the two knobs are bare of it. The foot runs back under the collar's front as the tube's own metal. The hinge's barrel and the clamp's nut are a steel of their own and the pin's two ends bright; the lever is drawn as the mount's black.","The magnifier's foot is a plain block under the objective tube as long and as wide as the riser; the riser and the mount's top plate are plain blocks (the keys by which the foot sits down into the riser and the riser onto the plate, the riser's slot, the screws and their holes aren't drawn). The riser is drawn fitted, as in EOTECH's own pictures of the kit; a seller's (Primary Arms') show it without.","Without the riser (the build's choice, D95) the magnifier is drawn on the mount's top plate, lower by as much as the ledger has its axis lower (EOTECH's 7 mm), its foot reaching down by what the side view's riser band is over 7 mm (a hundredth of an inch) to stand off the plate as the riser does: four models, in line and aside, each with the riser and without it. The screws are not drawn, so the shorter pair EOTECH gives for that way isn't either.","The mount is the G33's, by EOTECH's word (\"This is the standard mount that comes with the G33, G43 and G45\"), and drawn as that part's is, from that part's readings: the clamp a block with the rail's own head in section (MIL-STD-1913's) cut out of its underside down to the lower gauge line and plain jaws the rail's width apart below it; on the right the two hinge knuckles on their walls, the pin's ends, and the clamp's slotted nut as a plain disc; what swings is a round barrel between the knuckles, an arm from it to the top plate, the plate, the riser and the magnifier. The quick-detach lever is this picture's own outline at 0.2 in thick along the clamp's left, its tail to the rear: 0.06 in shorter than in EOTECH's picture of the G33 (lever_tail_behind_base keeps both). Its locking button and its pivot aren't drawn.","Swung aside it is turned 93.5 degrees about the hinge, over to the rifle's right: the same mount's angle, read between EOTECH's two rear views of the G33 on it (good to about 3 degrees); EOTECH's own picture of the G45 swung aside (EOTECH-G45-Black-2) shows the state and gives no angle. The magnifier then lies beside the rail with its eyepiece still to the rear, the knob that was on top pointing right.","Which side is which: the lever is on the rifle's left, the hinge and the knob marked R on its right, so the magnifier swings to the right. EOTECH's own views and the sellers' all have it so. The mount can be fitted to open to the left instead (its manual: \"so it opens either to the left or right (based on preference)\"); the model has the one arrangement.","Across the rifle the model is 2.12 in from the lever's face to the horizontal knob's, against EOTECH's 2.3: the lever's face is where the same mount's is on the G33 (1.0 in left of the rail's middle, from a close rear view good to 0.05 in), and the knob's is worked out from the side view as said above. And it is 3.76 in long over all (3.75 between the magnifier's two end faces) against EOTECH's 3.9, which no side view on file bears out: the ledger's entry for the length says what three of them read.","Lenses at the end faces: the objective's at 25 mm (one seller's row, \"Objective 25\"; the glass that shows in a view from ahead is 0.68 of the tube across, which is that within 0.04 in), the eyepiece's at the glass that shows in a view from behind (0.92 in, good to 0.08). Their recess behind the retainers, and the threads inside the objective's rim, aren't drawn."],"ledger":["eotech-g45.length","eotech-g45.width","eotech-g45.height","eotech-g45.optical_axis_above_rail_spacer","eotech-g45.eye_relief","eotech-g45.eyepiece_rear_behind_base","eotech-g45.riser_thickness","eotech-g45.sts_mount_length","eotech-g45.sts_mount_height","eotech-g45.flip_angle","eotech-g45.body_half_width","eotech-g45.side_knob_reach","eotech-g45.hinge_axis_above_clamp_bottom","eotech-g45.hinge_axis_right_of_centre","eotech-g45.clamp_below_rail","eotech-g45.knob_lugs","eotech-g45.diopter_flutes","eotech-g45.collar_pads"]},"profiles":{"side":{"plane":"xy","origin":"the middle of the mount's top plate (x over its rows), the clamp's bottom; offset to the rail's top","offset":{"y":"clamp_bottom_y"},"points":[[-2.932,2.692],[-2.928,1.625],[-2.921,1.481],[-2.904,1.448],[-2.879,1.441],[-2.676,1.446],[-2.645,1.467],[-2.641,1.547],[-2.592,1.548],[-2.582,1.557],[-2.577,1.408],[-2.562,1.393],[-2.503,1.386],[-1.239,1.377],[-1.134,1.396],[-0.804,1.398],[-0.803,1.139],[-0.828,1.128],[-0.83,0.904],[-0.808,0.86],[-0.709,0.859],[-0.711,0.592],[-1.308,0.581],[-1.316,0.571],[-1.318,0.489],[-1.318,0.09],[-1.296,0.08],[-0.699,0.089],[-0.693,0.086],[-0.702,0.079],[-0.716,0.019],[-0.703,0.011],[-0.314,0.011],[-0.065,0],[-0.001,0],[0.544,0.002],[0.692,0.009],[0.705,0.019],[0.702,0.147],[0.714,0.161],[0.714,0.496],[0.702,0.505],[0.709,0.573],[0.661,0.631],[0.654,0.852],[0.813,0.857],[0.83,0.877],[0.83,1.068],[0.81,1.096],[0.81,1.353],[0.798,1.367],[0.814,1.773],[0.819,2.416],[0.814,2.715],[0.791,2.945],[0.776,2.953],[-0.092,2.951],[-0.105,2.961],[-0.114,3.029],[-0.184,3.069],[-1.059,3.062],[-1.089,3.058],[-1.118,3.04],[-1.155,3.04],[-1.187,3.056],[-1.34,3.067],[-1.341,3.114],[-1.366,3.13],[-1.368,3.146],[-1.366,3.168],[-1.339,3.194],[-1.339,3.228],[-1.39,3.286],[-1.451,3.297],[-1.584,3.302],[-1.837,3.302],[-1.96,3.29],[-2.014,3.23],[-2.014,3.189],[-1.986,3.168],[-1.984,3.134],[-2.016,3.107],[-2.015,3.069],[-2.466,3.069],[-2.535,3.056],[-2.56,3.042],[-2.57,3.023],[-2.582,2.814],[-2.594,2.846],[-2.645,2.849],[-2.65,2.927],[-2.683,2.951],[-2.909,2.948],[-2.923,2.915]],"scaleRefs":["eotech-g45.sts_mount_length","eotech-g45.height"],"inputs":{"eotech-g45.height":3.2992125984251968,"eotech-g45.sts_mount_length":1.6614},"tolerance":0.006,"photo":"references/eotech-g45 64be77ba9788 (EOTECH's left side view, in line, the 7 mm riser fitted (the objective at the picture's left))","method":"alpha > 0.5, largest piece, holes filled; scale from eotech-g45.sts_mount_length = 1.6614 in (median width over 0.69–0.72 of the height from the top, 728–728 px 728 px → 438.2 px/in) and eotech-g45.height = 3.29921 in (y from the origin to the far edge 1448 px → 438.9 px/in), which agree within 0.2%; mean 438.5 px/in; origin at x center, y min of the outline (x over 0.69–0.72 of the height from the top); Douglas-Peucker at 0.006 in with the extremes kept: 94 points (IoU 0.998 with the full outline); checks: width 3.762 ± 0.007 in vs eotech-g45.length 3.751 ± 0.04 (conflict): agrees; −x_min 2.932 ± 0.004 in vs eotech-g45.eyepiece_rear_behind_base 2.933 ± 0.03 (provisional): agrees (tools/trace.py)","via":"harvest","note":"The outline encloses everything seen from the left: the housing, the knob on top, the riser, the mount and its lever. The lever is on this side; the hinge, on the far side, is behind the mount here."}},"gaps":[{"what":"The optical axis's height over the rail. No page states it: EOTECH's manual says only \"an absolute co-witness or lower-third co-witness height\". The 1.83 in drawn is the diopter ring's middle on EOTECH's side view over the rail's top where the same mount's clamp puts it, and that in turn rests on one reviewer's 47 mm for the G33.","need":"EOTECH's own centreline figure for the G45 on the STS mount with the riser, or a reviewer's rule on one."},{"what":"Anything across the magnifier: its body's width, where the horizontal knob's face is, its overall width (EOTECH: 2.3 in; the model 2.12). Every view on file is from the side or oblique.","need":"A straight view from above, from behind or from ahead (EOTECH's gallery has none for the G45)."},{"what":"What EOTECH's 3.9 in length spans: three side views have 3.75 to 3.83 in between the magnifier's two end faces.","need":"A reviewer's rule on the part, or EOTECH's word."},{"what":"The diopter ring's flutes: their number (20 drawn, from their spacing on two side views; 19 or 21 isn't excluded) and their depth (the G33's ring's, unread on this one).","need":"A view from behind, the ring's rear rim whole."},{"what":"The mount set to open to the left (EOTECH: \"Position the mount on the optic mount interface (or riser) so it opens either to the left or right (based on preference).\"): the model has the one arrangement EOTECH pictures, opening to the right.","need":"A decision to offer it as a choice: drawn mirrored about the rail's middle, as EOTECH's manual says it is set up."},{"what":"How deep the sunk panels in four of the collar's pads are (drawn as the pads' own relief, 0.027 in; the side views bracket it only from above), and the recess round each knob, which isn't drawn.","need":"A view along the housing where a panel meets the outline, or a close oblique one with a known width in it."}]},"expo-arms-mlok-15-handguard":{"id":"expo-arms-mlok-15-handguard","name":"Free Float AR-15 Handguard - M-LOK - 15\"","manufacturer":"Expo Arms","sku":"XP-GUARD15-BLK","url":"https://www.primaryarms.com/expo-arms-m-lok-handguard-black-15","category":"handguard","description":"Expo Arms' 15 in free-float M-LOK handguard (Expo Arms is Primary Arms' house brand): 6061-T6 aluminum, a full top Picatinny rail, M-LOK slots on seven sides, two anti-rotation tabs, clamped on its own 6061-T6 aluminum barrel nut by three cross bolts. \"Compatible with all Mil-Spec upper receivers\".","weight":"expo-arms-mlok-15-handguard.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"mount":{"origin":[0,0,0],"note":"The receiver's front face on the bore axis, +x toward the muzzle."},"mlok":{"origin":["{.mlok_slot0_x}",0,0],"note":"On the handguard's axis (the bore's: its octagon is about it) at the rearmost M-LOK slot's centre (index 0), +x toward the muzzle; the faces are angles about this axis (M10)."},"top_rail":{"origin":["{.rear_face_x} + {.rail_slot0_from_rear_face}","{.rail_top_above_bore}",0],"note":"The rail's top at its rearmost slot's centre, +x toward the muzzle (picatinny: index = slot number). Its own rail: the receiver's is the receiver's."}},"interfaces":{"handguard_mount":{"type":"ar15.handguard_mount","role":"handguard","anchor":"mount","params":{"nut":"standard"},"flips":false,"note":"Primary Arms: \"comes with a 6061-T6 aluminum barrel nut and anti-rotation tabs for a strong lock-up on any Mil-Spec receiver\"; \"Compatible with all Mil-Spec upper receivers\". The page names no thread: `standard` is what \"any Mil-Spec receiver\" takes, read as Aero's \"Compatible with mil-spec AR15 upper receivers\" is."},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}","beyond_seam":true,"seam_behind":"receiver","seam_ahead":"handguard"},"flips":false},"mlok":{"type":"mlok","role":"slots","anchor":"mlok","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_slots}","interval":"={std.mlok.interval}","face_distance":"={.diagonal_face_distance}","bore":"={.inside_diameter}","reach_inside":"={.reach_inside}"},"faces":{"right":{"angle":90,"note":"the rifle's right side (+z)"},"right_lower":{"angle":135},"bottom":{"angle":180},"left_lower":{"angle":-135},"left":{"angle":-90},"left_upper":{"angle":-45},"right_upper":{"angle":45}},"flips":false,"note":"How far an accessory's nuts may reach inside depends on what runs under it (a barrel, a gas block, a gas tube), other parts: reach_inside has no figure, so that check reads as unmade."}},"materials":{"body":{"label":"Handguard","finish":"anodized","recolorable":true,"color":"placeholder-black","options":{"black":{"label":"Black (hardcoat anodized)","finish":"anodized","color":"placeholder-black","sku":"XP-GUARD15-BLK","source":"https://www.primaryarms.com/expo-arms-m-lok-handguard-black-15"},"fde":{"label":"FDE (Cerakote)","finish":"cerakote","color":"expo-arms-fde","sku":"XP-GUARD15-FDE","source":"https://www.primaryarms.com/expo-arms-15-m-lok-handguard-flat-dark-earth-xp-guard15-fde"}},"default":"black","note":"Primary Arms: \"Black hardcoat anodized finish\"; the other's page, \"FDE Cerakote finish\" (Color: Flat Dark Earth, Finish: Cerakote). Its listing of Expo Arms' handguards has the 15 in M-LOK in these two and no other. The black is unmatched (sealed black anodize); the FDE is matched on Primary Arms' two side photos of XP-GUARD15-FDE."},"hardware":{"label":"Cross bolts and nut","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The clamp's three cross bolts (socket heads on the left, their ends on the right) and the nut between them on the right side: black on both the black and the FDE handguard's photos (looked at at full size, 2026-10-06: on the FDE one the heads and the nut are black against the tan, the bolts' ends a dark grey), so the slot follows nothing. Primary Arms doesn't say what they are made of (a buyer calls the nut steel, on a page of reviews the harvest didn't read); the colour is a placeholder."}},"components":{},"geometry":{"model":"expo-arms-mlok-15-handguard.glb","components":{},"approximations":["Its section run between its two end faces, 14.99 in apart: an octagon about the bore with its side flats 1.59 in apart (each side photo's own parallax: the near wall's slots against the far wall's), its diagonal faces 0.775 and its bottom 0.76 from the bore (their rows' and the silhouette's heights), the diagonals taken at 45 degrees; a neck up to a Picatinny rail with the standard's head in section (MIL-STD-1913's Figure 1, since 2026-10-12; the photos' teeth give a 0.64 in flat and the widest a tenth below the top, the standard's within their ±, and until then it was drawn as those two alone, its faces meeting sharp, 0.01 in inside the standard's), its lower faces carried on to where its underside's shadow ends, 0.21 below the top. No view down its length is on file, and the bore's level is taken as its middle row of slots'.","Bored to the published 1.35 in, round: the three-quarter photos show flats inside behind the rows and ribs between them, which aren't drawn. The channel up into the neck (the gas tube's) is as wide as the three-quarter photo shows it against the rail (0.45 in); its round roof is taken about the gas tube's standard height.","36 rail slots where its own teeth put them, cut at the standard's width and depth (its own read 0.222 in wide, more than the standard's .206); eight M-LOK slots in each of seven rows at the standard's size and pitch, on the lines through the bore every 45 degrees. The bottom's row isn't seen in a side view and is taken to match the six that are.","The clamp's block under its rear end from the traced side outline, as wide as the bottom flat (the three-quarter photos show its sides running on from the flat's edges); its three cross bolts as plain cylinders, socket heads on the left and their ends on the right, each drawn a hair proud. The clamp's steel nut as the FDE handguard's photo outlines it (a round about the middle bolt, a neck up to a blunt point), let into the lower diagonal face down to the plane of the block's side, where its face is taken to be. The wedge inside, the slit the bolts close and the barrel nut aren't drawn.","The two anti-rotation tabs as the side photos outline them, as thick as the wall is there. The Expo and M-LOK marks aren't drawn. Edges broken at 0.015 in.","Placed with its rear face at the receiver's front shoulder, 0.445 in behind the end of the barrel-nut thread (the Army drawing's thread length), where a buyer on its page says it is made to sit flush: no photo of it mounted is on file."],"ledger":["expo-arms-mlok-15-handguard.length","expo-arms-mlok-15-handguard.width","expo-arms-mlok-15-handguard.height","expo-arms-mlok-15-handguard.inside_diameter","expo-arms-mlok-15-handguard.rear_x","expo-arms-mlok-15-handguard.rail_top_above_bore","expo-arms-mlok-15-handguard.diagonal_face_distance","expo-arms-mlok-15-handguard.mlok_slot0_from_rear_face","expo-arms-mlok-15-handguard.rail_slot0_from_rear_face"]},"profiles":{"side":{"plane":"xy","origin":"the tabs' rear ends and the rail's top","offset":{"x":"rear_x","y":"rail_top_above_bore"},"points":[[0,-0.51],[0.003,-0.649],[0.123,-0.704],[0.159,-0.738],[0.116,-0.925],[0.12,-1.527],[0.238,-2.003],[0.32,-2.052],[0.402,-2.131],[0.458,-2.231],[0.525,-2.303],[0.611,-2.347],[1.53,-2.36],[1.762,-2.356],[1.823,-2.339],[1.969,-2.259],[2.134,-2.047],[2.195,-2.007],[2.264,-1.991],[15.021,-1.98],[15.062,-1.937],[15.17,-1.549],[15.18,-1.248],[15.174,-0.916],[15.064,-0.455],[15.073,-0.115],[14.982,-0.02],[14.45,-0.03],[14.395,-0.016],[14.133,-0.013],[14.071,-0.03],[14.017,-0.016],[13.793,-0.012],[13.685,-0.03],[13.469,-0.011],[13.353,-0.013],[13.299,-0.03],[13.152,-0.009],[12.982,-0.013],[12.921,-0.029],[12.789,-0.009],[12.596,-0.013],[12.535,-0.029],[12.457,-0.008],[12.218,-0.012],[12.149,-0.029],[12.079,-0.007],[11.839,-0.012],[11.762,-0.029],[11.693,-0.007],[11.453,-0.012],[11.384,-0.036],[11.299,-0.007],[11.067,-0.012],[10.998,-0.036],[10.913,-0.007],[10.689,-0.011],[10.604,-0.036],[10.519,-0.007],[10.303,-0.011],[10.218,-0.036],[10.133,-0.007],[9.917,-0.011],[9.832,-0.043],[9.786,-0.037],[9.739,-0.007],[9.538,-0.011],[9.492,-0.042],[9.446,-0.051],[9.4,-0.044],[9.345,-0.007],[9.206,-0.002],[9.053,-0.051],[9.006,-0.044],[8.951,-0.007],[8.843,-0.001],[8.789,-0.002],[8.72,-0.042],[8.666,-0.051],[8.62,-0.044],[8.565,-0.006],[8.457,-0.001],[8.403,-0.002],[8.327,-0.05],[8.28,-0.058],[8.218,-0.044],[8.171,-0.006],[8.094,0],[8.009,-0.002],[7.941,-0.05],[7.887,-0.058],[7.84,-0.052],[7.778,-0.006],[7.662,-0.001],[7.623,-0.002],[7.577,-0.041],[7.501,-0.066],[7.423,-0.044],[7.384,-0.006],[7.314,0],[7.221,-0.002],[7.153,-0.057],[7.099,-0.066],[7.022,-0.044],[6.982,-0.007],[6.92,0],[6.828,-0.002],[6.79,-0.041],[6.713,-0.066],[6.635,-0.044],[6.596,-0.006],[6.527,0],[6.434,-0.002],[6.373,-0.049],[6.319,-0.058],[6.242,-0.036],[6.21,-0.006],[6.117,0],[6.04,-0.002],[6.01,-0.033],[5.933,-0.058],[5.887,-0.051],[5.816,-0.006],[5.723,0],[5.646,-0.002],[5.593,-0.041],[5.539,-0.05],[5.493,-0.043],[5.438,-0.006],[5.314,-0.001],[5.252,-0.002],[5.199,-0.041],[5.153,-0.05],[5.107,-0.043],[5.052,-0.006],[4.944,0],[4.859,-0.002],[4.813,-0.034],[4.759,-0.042],[4.713,-0.035],[4.666,-0.006],[4.48,-0.001],[4.373,-0.042],[4.326,-0.035],[4.28,-0.005],[4.117,-0.001],[4.071,-0.002],[3.979,-0.034],[3.893,-0.005],[3.708,-0.001],[3.593,-0.034],[3.507,-0.005],[3.276,-0.01],[3.207,-0.034],[3.121,-0.005],[2.882,-0.01],[2.813,-0.026],[2.743,-0.005],[2.488,-0.01],[2.419,-0.026],[2.349,-0.005],[2.102,-0.009],[2.033,-0.026],[1.955,-0.005],[1.716,-0.009],[1.655,-0.026],[1.507,-0.006],[1.322,-0.009],[1.268,-0.026],[1.098,-0.006],[0.936,-0.009],[0.882,-0.026],[0.666,-0.007],[0.226,-0.015],[0.193,-0.089],[0.21,-0.189],[0.214,-0.374],[0.199,-0.413],[0.123,-0.477],[0.169,-0.483],[0.019,-0.49]],"scaleRefs":["expo-arms-mlok-15-handguard.overall_length"],"inputs":{"expo-arms-mlok-15-handguard.overall_length":15.18},"tolerance":0.01,"photo":"references/expo-arms-mlok-15-handguard b0ebc4d7c105 (Primary Arms' gallery for XP-GUARD15-BLK, photo _01: the handguard's right side on white, the receiver's end at the left, 2200 x 1467)","method":"luminance < 200, largest piece, holes filled, notches filled in [130, 570, 2100, 640] (disk closing, r 18 px); rotated +1.1° as declared; scale from expo-arms-mlok-15-handguard.overall_length = 15.18 in (x-extent 1966 px → 129.5 px/in); origin at x min, y max of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 181 points (IoU 0.997 with the full outline); checks: −y_min in x [4, 14] 1.993 ± 0.012; −y_min 2.360 ± 0.012 (tools/trace.py)","via":"harvest","note":"The M-LOK slots are inside the outline (its holes filled) and the rail's slots are filled to the teeth's tops: the model cuts both. Its rear end is the tip of the right-hand tab; the block under the rear end is the clamp's."}},"gaps":[{"what":"Where it seats on a receiver (its rear face is taken at the standard's front shoulder)","need":"A photo of it mounted on an upper whose lug holes show, or Primary Arms' instructions for it (none are published)"},{"what":"Its section: its width, the flats inside, the channel's roof","need":"A view down its length with its rail in frame (Primary Arms' three photos have none)"},{"what":"The room inside its faces before what runs under it (reach_inside: what an M-LOK accessory's nuts may take)","need":"The barrel's and the gas block's sizes under the slots: the build's, once those parts state them"},{"what":"Which weight is the handguard's: 13.2 oz on its page, 18.2 oz on the FDE one's, and neither says whether the barrel nut is counted","need":"A weighed figure with the nut said to be on or off"},{"what":"The FDE Cerakote variant (XP-GUARD15-FDE)","need":"A colour preset for Expo's FDE Cerakote, matched on Primary Arms' photos of it"},{"what":"Whether a low-profile gas block clears it","need":"A rule from Primary Arms' sentence (\"the generous internal diameter leaves room for a low-profile gas block\") once a gas block states its height over the bore"}]},"expo-arms-stripped-upper":{"id":"expo-arms-stripped-upper","name":"7075 Stripped AR-15 Upper Receiver","manufacturer":"Expo Arms","sku":"XP-UPPER","url":"https://www.primaryarms.com/expo-arms-ar-15-7075-stripped-upper-receiver","category":"upper","description":"Expo Arms' stripped upper: a \"Precision machined 7075-T6 aluminum forging\" with \"M4 feed ramp cuts\" and a \"MIL-SPEC Type III Class 2 hardcoat anodized finish\", its rail unmarked (\"T Marks: Unmarked\"). It \"Accepts MIL-SPEC upper parts\" and \"is compatible with standard mil-spec lowers, handguards, and barrels\". \"Port door and forward assist hardware not included\".","weight":"expo-arms-stripped-upper.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"pins":{"origin":[0,0,0]},"front_face":{"origin":["{.front_face_x}","{.bore_axis_above_pin}",0],"note":"The end of the barrel-nut thread on the bore axis, +x toward the muzzle: a barrel extension's flange seats here, and a handguard is placed from here."},"rear_face":{"origin":["{.receiver_rear_x}","{.bore_axis_above_pin}",0],"note":"The rear face on the bore axis, +x toward the muzzle: the bolt carrier's channel opens here."},"handle_channel":{"origin":["{.handle_seat_x}","{.bore_axis_above_pin} + {.charging_handle_above_bore}",0],"note":"The charging handle's seat on its channel's axis, +x toward the muzzle: the front wall of the open notch under the rail's rear end, which the handle's shoulder stops against, at the notch's mid-height. (At the rear face until 2026-10-05: the handle hung 0.69 in behind where it belongs.)"},"top_rail":{"origin":["{.rail_slot0_x}","{.rail_top_above_pin}",0],"note":"The rail's top at its rearmost slot's centre, +x toward the muzzle (picatinny: index = slot number)."}},"interfaces":{"receiver_pins":{"type":"ar15.upper_lower","role":"upper","anchor":"pins","params":{"pin_spacing":"={std.ar15.pin_spacing}"},"flips":false},"barrel_extension":{"type":"ar15.barrel_extension","role":"receiver","anchor":"front_face","params":{},"flips":false},"handguard_mount":{"type":"ar15.handguard_mount","role":"receiver","anchor":"front_face","params":{"nut":"standard"},"flips":false,"note":"Primary Arms: \"It is compatible with standard mil-spec lowers, handguards, and barrels\"."},"carrier_channel":{"type":"ar15.carrier_channel","role":"receiver","anchor":"rear_face","params":{},"flips":false},"charging_handle_channel":{"type":"ar15.charging_handle_channel","role":"receiver","anchor":"handle_channel","params":{},"flips":false},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}","seam":"={.rail_front_x} - {.rail_slot0_x}","seam_parts":"the receiver's rail and the handguard's","seam_behind":"receiver","seam_ahead":"handguard"},"flips":false,"note":"Its own rail of 13 slots, read off Primary Arms' side photo; a handguard's rail ahead of it is the handguard's own."}},"materials":{"receiver":{"label":"Receiver","finish":"anodized","recolorable":true,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized","color":"placeholder-black","sku":"XP-UPPER","source":"https://www.primaryarms.com/expo-arms-ar-15-7075-stripped-upper-receiver"}},"default":"black","note":"Sold in one colour: its page's \"Color: Black\", \"Finish: Hardcoat Anodized\"."}},"components":{},"geometry":{"components":{"receiver":"expo-arms-stripped-upper.receiver.glb"},"approximations":["Drawn stripped, as it is sold: the forward assist's bore empty and the ejection port without its door.","Its side outline (Primary Arms' level right-side photo, in the frame of its own lug holes) across the mil-spec forging's section: the Army drawing's forged 1.18 round body, the rail's lower faces under its slots' floors the standard's (MIL-STD-1913's, since 2026-10-12: the reference model has them a hundredth further out, and every clamp stood in them), the height of its dovetail's foot, its neck, the flat sides and the walls from the reference CAD set (a third-party model of a mil-spec forging). No end or top view of this receiver is on file, so its own section isn't sourced; its photos show the section's two lines along the side where that model has them. The lower of the two, the model's step at the neck's foot (a ledge .010 wide where the neck meets the flat side a hundredth further out), isn't drawn (2026-10-12): at the size the page draws a rifle it is a third of a pixel, and it drew as a dashed hairline along the body; the neck's wall leans from its width under the dovetail's foot out to the side's face at the height of the step.","On the right, the forward assist's housing is a cylinder about the Army drawing's axis (20° in plan, placed by the reference model) from where the photo shows its rear face, solid back to the wall, its .509 bore open; the brass deflector is the photo's outline, rising to the reference model's crest and sloping to the port; the port is the drawing's (3.125 long, the photo's opening reads 0.06 shorter); the door's two hinge lugs are where the photo shows them, about the reference model's pin axis. How far each stands out is the forging's, not measured on this receiver.","On the left, the cam pin's pad is the left photo's outline out to the reference model's face, and the charging handle latch's slot is the photo's, a pocket in the wall down to the drawing's .045 over the channel (8448524 Section D-D; cut through into the channel until 2026-10-20). What the photos show nearer their lens than the mid-plane is brought back by its depth, with the lens placed by the two lug holes in each photo.","Behind its rail's head the rail is the standard's tongue (2026-10-20, lib.rail_tongue: the reference model's, ±0.318 with a round end, its rearmost point where this receiver's photo has the rail's end, and two concave rounds out to the head's width by 0.4165 ahead of the pin, where the app's head begins): until then the head was drawn at its full width to the rail's end, square, and every charging handle's T stood in its two corners. The charging handle's channel is the standard's (lib.handle_channel: the Army drawing's tier and roof, 8448524 sheet 2, and the reference model's widths and its two upright rounds), and so is the notch the handle's block lies in at least (lib.handle_notch: the reference model's floor, roof and 45 degree corners); a handle rides on its guide lugs on the tier (std.ar15.charging_handle_axis_y), which this receiver's photo, reading the see-through notch's middle, agrees with within its ±.","The barrel nut's thread is turned as rings at the drawing's pitch and diameters, not a helix; the gas tube's hole, the charging handle's channel, the flange round the rear end is the drawing's and the reference model's, and the lower rear corner is cut to the arc a lower's two rear walls rise along (the Army's .750 R, drawing 8448608 sheet 1: this upper's own drawing has .760, a hundredth clear of them, which isn't drawn since 2026-10-12: it was a slit across the rifle). The lugs are the side outline at the drawing's width.","Not drawn: the port door's seat and its detent, the M4 feed ramps, the openings in the underside (it is closed under the bore), the forge mark and the takedown lug's countersink; edges broken at 0.015 in."],"ledger":["expo-arms-stripped-upper.receiver_rear_x","expo-arms-stripped-upper.front_face_x","expo-arms-stripped-upper.underside_y","expo-arms-stripped-upper.rail_top_above_pin","expo-arms-stripped-upper.bore_axis_above_pin"]},"profiles":{"side":{"plane":"xy","origin":"the takedown pin centre (the rifle frame origin), +x toward the muzzle","offset":{},"points":[[-0.621,1.594],[-0.621,0.645],[-0.561,0.543],[-0.378,0.403],[-0.244,0.323],[-0.243,-0.132],[-0.225,-0.22],[0.222,-0.219],[0.244,-0.202],[0.247,-0.163],[0.247,0.238],[0.634,0.245],[6.135,0.246],[6.134,-0.032],[6.161,-0.102],[6.222,-0.163],[6.335,-0.209],[6.467,-0.209],[6.568,-0.154],[6.62,-0.082],[6.624,0.241],[6.651,0.245],[6.657,0.297],[6.68,0.262],[6.719,0.282],[6.746,0.259],[6.774,0.282],[6.801,0.259],[6.828,0.282],[6.859,0.259],[6.883,0.282],[6.902,0.259],[6.933,0.278],[6.972,0.259],[7.036,0.303],[7.036,1.45],[6.998,1.485],[6.962,1.478],[6.947,1.489],[6.908,1.477],[6.865,1.489],[6.853,1.477],[6.822,1.493],[6.799,1.477],[6.764,1.493],[6.744,1.477],[6.713,1.493],[6.678,1.458],[6.634,1.463],[6.633,1.899],[6.648,2.012],[6.627,2.1],[6.183,2.099],[6.107,2.07],[6.093,1.982],[5.992,1.982],[5.969,2.099],[5.871,2.103],[5.794,2.102],[5.723,2.075],[5.712,1.986],[5.591,1.985],[5.576,2.098],[5.463,2.102],[5.396,2.102],[5.338,2.078],[5.323,1.985],[5.194,1.985],[5.176,2.1],[5.12,2.101],[4.995,2.101],[4.943,2.072],[4.929,1.984],[4.809,1.984],[4.787,1.994],[4.774,2.105],[4.606,2.104],[4.579,2.093],[4.554,2.071],[4.54,1.988],[4.396,1.987],[4.376,2.104],[4.201,2.104],[4.164,2.075],[4.155,1.987],[3.999,1.987],[3.983,2.103],[3.8,2.103],[3.775,2.078],[3.769,1.99],[3.594,1.99],[3.586,2.103],[3.407,2.106],[3.386,2.077],[3.384,2.028],[3.401,2.073],[3.396,1.99],[3.193,1.989],[3.185,2.106],[3.006,2.106],[3.002,1.993],[2.8,1.989],[2.784,2.105],[2.621,2.109],[2.603,2.103],[2.603,1.994],[2.555,1.988],[2.395,1.992],[2.393,2.099],[2.379,2.109],[2.212,2.108],[2.202,1.997],[2.122,1.991],[1.998,1.991],[1.996,2.094],[1.982,2.108],[1.811,2.108],[1.805,2.004],[1.788,1.991],[1.593,1.994],[1.593,2.01],[1.61,2.004],[1.61,2.078],[1.589,2.107],[1.41,2.107],[1.394,1.99],[1.223,1.99],[1.207,2.091],[1.188,2.107],[1.083,2.11],[-0.467,2.108],[-0.587,2.096],[-0.589,1.931],[-0.505,1.909],[-0.498,1.894],[0.013,1.891],[0.069,1.83],[0.069,1.675],[-0.014,1.591]],"features":{"forward_assist_housing":[[[-0.543,1.234],[0.489,1.232],[1.111,1.213],[1.267,1.174],[1.423,1.105],[1.54,1.019],[1.618,0.93],[1.657,0.864],[1.618,0.774],[1.541,0.676],[1.424,0.606],[1.268,0.559],[0.879,0.527],[0.1,0.526],[-0.445,0.533],[-0.562,0.564],[-0.659,0.673],[-0.69,0.829],[-0.695,0.984],[-0.679,1.101],[-0.633,1.187]]],"forward_assist_bore":[[[-0.644,1.148],[-0.477,1.148],[-0.476,0.615],[-0.643,0.615]]],"deflector":[[[2.045,1.658],[2.103,1.697],[2.863,1.71],[2.933,1.574],[2.98,1.419],[2.988,1.068],[2.961,0.881],[2.767,0.873],[2.066,0.872],[2.031,0.93]]],"deflector_crest":[[[2.318,1.671],[2.395,1.671],[2.396,1.145],[2.318,1.145]]],"port":[[[2.98,1.38],[6.087,1.385],[6.088,0.847],[2.981,0.842]]],"hinge_rear":[[[2.786,0.795],[2.961,0.796],[2.962,0.515],[2.787,0.515]]],"hinge_front":[[[6.181,0.801],[6.348,0.801],[6.349,0.521],[6.182,0.521]]]},"scaleRefs":["std.ar15.pin_spacing"],"inputs":{"expo-arms-stripped-upper.front_face_x":7.036,"expo-arms-stripped-upper.receiver_rear_x":-0.621,"std.ar15.pin_spacing":6.375},"tolerance":0.01,"photo":"references/expo-arms-stripped-upper aad70ef8abd5 (Primary Arms' XP-UPPER_02: the stripped receiver's right side, level, 2200 x 1467)","method":"luminance < 200, largest piece, holes filled; frame from the reviewed holes takedown, pivot (256.9 px/in, rms 0.000 in over 2 points); origin at the photo's frame; clipped to x min {.receiver_rear_x} = -0.621, x max {.front_face_x} = 7.036; Douglas-Peucker at 0.01 in with the extremes kept: 139 points (IoU 0.997 with the full outline); checks: top (tooth tops: the edge's max over 0.4 in windows) along x [1.0, 6.0] 2.107 ± 0.012; x_min in y [1.45, 1.62] -0.666 ± 0.006; x_min in y [1.95, 2.2] -0.589 ± 0.006; x_max in y [0.6, 1.2] 7.121 ± 0.009; x_max in y [1.6, 2.2] 6.648 ± 0.008; y_min in x [1.0, 5.5] 0.238 ± 0.006; y_max in x [6.7, 7.0] 1.493 ± 0.006; y_min in x [6.7, 7.0] 0.259 ± 0.006; y_max in x [-0.5, -0.1] in y [1.2, 1.75] 1.595 ± 0.006; y_min in x [-0.45, -0.1] in y [1.75, 2.05] 1.894 ± 0.006; features through the same placement (forward_assist_housing: the housing's outline from the right: its rear rim, the creases above and below it, its nose where it runs into the body; forward_assist_bore: the bore's rear opening, the dark ellipse; deflector: the brass deflector's outline: its steep rear face from u 796, the crease at u 870 to 890, its long lit slope to the port's rear end; deflector_crest: the crease between the deflector's rear face and its slope; port: the ejection port's opening, the dark obround; hinge_rear: the port door's rear hinge lug; hinge_front: the port door's front hinge lug) (tools/trace.py)","via":"harvest","note":"Its outer silhouette with the lug holes filled, cut at the standard's rear and front faces (the silhouette's own ends are the forward assist's rim and the thread's near rim, nearer the lens); the forward assist, the deflector, the port and the door's hinge lugs as the photo shows them, inside it."},"left":{"plane":"xy","origin":"the takedown pin centre (the rifle frame origin), +x toward the muzzle; the left side seen mirrored","offset":{},"points":[[-0.723,1.033],[-0.71,0.793],[-0.628,0.577],[-0.472,0.399],[-0.254,0.264],[-0.246,-0.149],[-0.23,-0.228],[-0.012,-0.237],[0.197,-0.237],[0.246,-0.188],[0.257,-0.113],[0.249,0.19],[0.263,0.196],[2.895,0.195],[2.974,0.18],[4.349,0.17],[6.141,0.188],[6.139,-0.022],[6.218,-0.16],[6.303,-0.221],[6.428,-0.232],[6.55,-0.185],[6.615,-0.096],[6.614,0.194],[6.638,0.21],[6.64,0.291],[6.675,0.291],[6.695,0.255],[6.726,0.279],[6.762,0.256],[6.785,0.279],[6.801,0.256],[6.821,0.256],[6.84,0.279],[6.856,0.256],[6.876,0.256],[6.895,0.279],[6.911,0.256],[6.931,0.256],[6.95,0.279],[6.966,0.256],[6.986,0.256],[7.058,0.309],[7.093,0.447],[7.113,0.714],[7.104,1.193],[7.068,1.425],[7,1.494],[6.972,1.47],[6.941,1.497],[6.921,1.466],[6.886,1.497],[6.866,1.466],[6.831,1.497],[6.811,1.466],[6.776,1.497],[6.752,1.466],[6.732,1.497],[6.717,1.497],[6.697,1.462],[6.636,1.464],[6.647,2.029],[6.643,2.065],[6.574,2.114],[6.134,2.113],[6.125,2.017],[6.107,1.999],[5.977,1.999],[5.971,2.064],[5.914,2.113],[5.741,2.113],[5.728,2.005],[5.628,1.999],[5.571,2.004],[5.571,2.059],[5.525,2.112],[5.349,2.112],[5.339,2.008],[5.325,1.998],[5.172,2.002],[5.166,2.063],[5.128,2.112],[4.952,2.112],[4.946,2.007],[4.905,1.998],[4.771,1.997],[4.765,2.062],[4.736,2.111],[4.559,2.111],[4.553,2.003],[4.457,1.997],[4.366,2.001],[4.36,2.066],[4.339,2.111],[4.166,2.11],[4.16,2.014],[4.17,2.063],[4.176,2.006],[4.095,2],[3.962,2],[3.946,2.11],[3.773,2.11],[3.769,2],[3.616,1.996],[3.559,1.998],[3.553,2.11],[3.38,2.109],[3.368,1.999],[3.258,1.995],[3.158,2.001],[3.16,2.109],[2.983,2.109],[2.96,1.995],[2.775,1.999],[2.763,2.109],[2.59,2.108],[2.569,2.063],[2.565,2],[2.48,1.998],[2.384,2],[2.374,2.108],[2.201,2.108],[2.168,2.063],[2.164,2],[2.123,1.998],[1.993,1.998],[1.977,2.107],[1.808,2.107],[1.767,2.062],[1.763,1.999],[1.75,1.993],[1.604,1.997],[1.588,2.107],[1.415,2.107],[1.366,2.061],[1.357,1.993],[1.215,1.993],[1.191,2.106],[-0.062,2.105],[-0.577,2.088],[-0.618,2.074],[-0.618,1.992],[-0.614,1.906],[-0.58,1.896],[-0.569,1.868],[-0.046,1.865],[0.043,1.781],[0.047,1.631],[0.006,1.594],[-0.592,1.597],[-0.609,1.587],[-0.615,1.55],[-0.678,1.546]],"features":{"cam_pin_pad":[[[5.668,1.462],[5.628,1.572],[5.53,1.619],[4.685,1.618],[4.587,1.571],[4.548,1.461],[4.548,1.205],[4.588,1.107],[4.686,1.06],[5.531,1.061],[5.629,1.109],[5.668,1.207]]],"latch_slot":[[[0.371,1.828],[0.343,1.895],[0.284,1.919],[0.225,1.895],[0.198,1.828],[0.198,1.592],[0.226,1.526],[0.285,1.502],[0.344,1.526],[0.371,1.593]]]},"scaleRefs":["std.ar15.pin_spacing"],"inputs":{"std.ar15.pin_spacing":6.375},"tolerance":0.01,"photo":"references/expo-arms-stripped-upper 8888fc8d0ccb (Primary Arms' XP-UPPER_03: the stripped receiver's left side, from above, 2200 x 1467)","method":"luminance < 200, largest piece, holes filled; frame from the reviewed holes takedown, pivot (254.5 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.01 in with the extremes kept: 153 points (IoU 0.996 with the full outline); checks: top (tooth tops: the edge's max over 0.4 in windows) along x [1.0, 6.0] 2.110 ± 0.012; x_min in y [1.45, 1.62] -0.684 ± 0.006; x_max in y [0.6, 1.2] 7.113 ± 0.009; y_min in x [1.0, 5.5] 0.170 ± 0.006; features through the same placement (cam_pin_pad: the raised pad over the cam pin's travel: the foot of its rounded edge; latch_slot: the charging handle latch's slot through the left wall, the dark obround) (tools/trace.py)","via":"harvest","note":"The left side's silhouette, lug holes filled: from above, so its lower edges read low; used for the body's lower rear and this side's features."}},"gaps":[{"what":"Its weight","need":"A page that states one: Primary Arms' (the brand owner's) gives none, and no seller or reviewer on file does. Not estimated: a build with it says its total weight is unknown"},{"what":"Its width, and how far its forward assist housing and deflector stand out","need":"An end or a top view with a known size in frame: the mil-spec forging's figures stand in"},{"what":"A forward assist and a port door for it","need":"Those parts in the catalog: it is sold without them, and drawn without them"}]},"faxon-16-pencil-barrel":{"id":"faxon-16-pencil-barrel","name":"Duty Series Pencil Profile 16\" Mid-Length 5.56 NATO AR15 Barrel","manufacturer":"Faxon Firearms","sku":"15A58M16NPQ","url":"https://faxonfirearms.com/15A58M16NPQ","category":"barrel","description":"Faxon's lightest 16 in 5.56 barrel, stripped, in its pencil profile: 4150 CMV, salt-bath QPQ nitride inside and out, 1:8 twist, a mid-length gas port (.081) on a .625 in journal 1.1 in long, an M4 feed ramp extension in black oxide, a 1/2x28 muzzle thread. Faxon: \"The lightest AR-15 barrel contour: a .625″ gas journal with the body tapered on both sides of it\"; \"At 1.20 lb it is Faxon’s lightest 16″ 5.56 barrel.\" It comes with no gas block, gas tube or muzzle device.","weight":"faxon-16-pencil-barrel.weight","barrelLength":"faxon-16-pencil-barrel.length","cartridge":{"takes":["5.56 NATO"],"stated":"Cartridge / chamber 5.56 NATO (fires 5.56 NATO and .223 Rem)","source":"https://faxonfirearms.com/15A58M16NPQ (Faxon's specifications table, as cached: harvest.quote; Primary Arms' table for the same number: \"Caliber Gauge 5.56 NATO\")"},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"extension":{"origin":[0,0,0],"note":"The barrel extension's flange, its rear face, on the bore axis, +x toward the muzzle."},"muzzle":{"origin":["{.shoulder_x}",0,0]},"gas_journal":{"origin":["{.gas_port_x}",0,0]}},"interfaces":{"barrel_extension":{"type":"ar15.barrel_extension","role":"barrel","anchor":"extension","params":{},"flips":false,"note":"Faxon: \"M4 feed-ramp barrel extension, black oxide, installed at 150 ft-lb, pinned, and headspaced\"; its fitment table: \"Upper receiver Any mil-spec AR-15 upper; M4 feed ramps match a ramped upper and work with a non-ramped one\"."},"muzzle":{"type":"muzzle_thread","role":"barrel","anchor":"muzzle","params":{"thread":"1/2-28","thread_length":"={.thread_length}"},"flips":false,"note":"Faxon: \"Muzzle 1/2x28 UNF-2A, .625″ of thread, target crown\" (Primary Arms: \"Threaded 1/2x28\"). No muzzle device comes with it: \"NOT INCLUDED Gas block (.625″), mid-length gas tube, muzzle device.\" The thread seats a device on the .615 in shoulder behind it."},"gas_journal":{"type":"ar15.gas_journal","role":"barrel","anchor":"gas_journal","params":{"journal_od":"={.journal_od}"},"flips":false,"note":"Faxon, on what it takes: \"A .625″ gas block on the 1.1″ journal and a mid-length gas tube.\" and \".625″ block on the 1.1″ journal (use a block 1″ long or shorter), mid-length tube.\" On what it comes with: \"NOT INCLUDED Gas block (.625″), mid-length gas tube, muzzle device.\" The journal runs from 8.85 to 9.96 in ahead of the receiver's face, a collar behind it; the port is 0.29 in ahead of the collar's face. The journal isn't dimpled for a set screw (the seller Right to Bear's table: \"Dimpled? No\"). A block bored for the commoner .750 journal doesn't fit it."},"gas_system":{"type":"ar15.gas_system","role":"barrel","params":{"length":"mid"},"flips":false,"note":"Faxon: \"Gas system Mid-length; .081″ port, reamed to size\" and \"Mid-length is the right gas system for a 16″ 5.56, and this barrel needs a mid-length gas tube.\" What the platform checks a gas tube against a barrel by (D83)."}},"materials":{"barrel":{"label":"Barrel","finish":"nitride","recolorable":false,"color":"steel-nitride-black","sheen":"matte","note":"Faxon: \"Finish Salt-bath QPQ nitride, bore and exterior\" and, of the nitride, \"It also gives the barrel its corrosion resistance and matte black finish.\" (Primary Arms: \"QPQ nitride finish\"). The one finish this number is sold in: no colourways. A black, not fitted to a photo, as the catalog's other nitrided parts (data/colors/steel.yaml, steel-nitride-black): in Primary Arms' side view (f09ad3b5be48) the tube reads #3d3c3d ahead of the journal and #424241 along the long taper, a dark grey with one soft band of light along it, where the app draws it #222223 in the hero direction; BCM's phosphate barrel reads #3a3a38 in the same studio. Its `matte` sheen is the maker's word. Not drawn: the lasered Faxon shield on the chamber journal and \"5.56 NATO 1-8 T\" ahead of the gas block (marks)."},"extension":{"label":"Barrel extension","finish":"nitride","recolorable":false,"color":"steel-nitride-black","sheen":"satin","note":"Faxon: \"M4 feed-ramp barrel extension, black oxide\" and \"It ships with the black-oxide M4 extension installed, torqued, pinned, and headspaced.\" Glossier than the nitrided tube ahead of it in Primary Arms' side view (f09ad3b5be48: the same #3e3d3e at its middle, black along its edges and a line of light between) and its close view of the breech (21ee264e9f0f: a hard line of light along the extension, none on the chamber journal beside it). The catalog has no finish type for black oxide: it is drawn as the polished black (`nitride`) with its satin sheen, and a black isn't fitted to a photo. Inside a receiver it is out of sight; it shows in the exploded view."},"pin":{"label":"Index pin","finish":"steel","recolorable":false,"color":"stainless-natural","note":"The extension's index pin is bare bright steel in Primary Arms' close view of the breech (21ee264e9f0f) and in Faxon's own (bedba5803d29): a silver dot on the black extension. Drawn as bare steel in the app's natural-steel grey, not matched to a photo (a pin an eighth of an inch across)."}},"components":{},"geometry":{"model":"faxon-16-pencil-barrel.glb","components":{},"approximations":["Turned station by station, extension to muzzle. Its diameters are Faxon's published ones where its sentence gives one (the .980 chamber journal, the .625 gas block journal, the .615 muzzle shoulder) and the standard's for the extension's body; the rest (the flange, the two ends of the long taper behind the gas block, the collar, the section ahead of the journal) and every station along the barrel are read off Primary Arms' side photo of this number at one scale, which the published length sets and the published journal diameter, journal length and thread length each bear out within a hundredth.","The section ahead of the gas block journal is drawn level at 0.50 in, as both photographs of the barrel show it (Faxon's own and Primary Arms'). Faxon's sentence has the barrel \"tapered from .625″ to .525″ ahead of\" the journal; the photographs have the .525 just behind the collar, at the thin end of the long taper. Both figures are in the ledger (forward_od), the conflict kept.","The collar behind the gas block journal (0.755 in across, 0.18 long) is the photographs': Faxon's profile sentence doesn't name it. The three places where the barrel changes diameter along a curve (up to the collar, down from the journal, up to the muzzle ring) are each one circular arc through the two stations read off the photo, level where it meets the thinner section: a round-nosed tool's, 0.43 in in radius at all three by the photo's stations.","The extension is the standard's: its body at the Army drawing's .999, its rear opening turned at the reference CAD set's sizes (its chamfered mouth, the ring its locking lugs make, the recess ahead of them); its flange and its length behind the receiver's face as the photo has them. It, the barrel and the index pin are three pieces in three material slots, the barrel standing four thousandths into the extension's front face and the pin into its top.","The index pin at the Army's .1255, where and as high as the photo has it; the gas port on top of the journal at Faxon's .081, where Primary Arms' close view of the journal has it (0.29 in ahead of the collar); the bore one plain hole right through, at the Army drawing's .219.","The muzzle thread is a helix, 28 to the inch, between the minor and major diameters of the Army barrel's 1/2-28 thread (Faxon states 1/2x28 UNF-2A): a plain V without the flats of its form, right-hand (assumed: its designation marks no other), over Faxon's .625 in, running out at the shoulder over its last pitch.","Not drawn: the chamber, the slots between the extension's locking lugs and its feed ramps (the lugs are one ring), the rifling, the target crown at the muzzle (\"11-degree target crown\" by Primary Arms: its width isn't sourced), the relief at the collar's foot (0.03 in wide, 0.011 deep) and the one behind the thread, the lasered marks."],"ledger":["faxon-16-pencil-barrel.overall_length","faxon-16-pencil-barrel.extension_rear_x","faxon-16-pencil-barrel.flange_front_x","faxon-16-pencil-barrel.shoulder_x","faxon-16-pencil-barrel.gas_port_x","faxon-16-pencil-barrel.journal_od","faxon-16-pencil-barrel.muzzle_od"]},"profiles":{"side":{"plane":"xy","origin":"the silhouette's rear tip, on the axis; the outline begins at the extension's rear face","offset":{"x":"extension_rear_x"},"points":[[0.103,0.49],[0.103,-0.481],[0.114,-0.49],[0.911,-0.49],[0.92,-0.499],[0.939,-0.49],[1.021,-0.49],[1.035,-0.504],[1.053,-0.559],[1.085,-0.582],[1.204,-0.582],[1.236,-0.549],[1.255,-0.495],[1.287,-0.481],[1.625,-0.481],[1.644,-0.49],[1.653,-0.481],[1.864,-0.481],[1.873,-0.49],[1.882,-0.481],[1.983,-0.472],[1.992,-0.462],[2.047,-0.462],[2.092,-0.444],[2.303,-0.417],[2.358,-0.398],[2.404,-0.398],[2.459,-0.38],[2.56,-0.371],[2.605,-0.353],[2.66,-0.353],[2.669,-0.343],[2.77,-0.334],[2.825,-0.316],[2.889,-0.316],[2.898,-0.307],[4.244,-0.307],[4.263,-0.298],[4.281,-0.307],[4.29,-0.298],[5.664,-0.298],[5.673,-0.288],[5.682,-0.298],[5.728,-0.298],[5.746,-0.288],[5.755,-0.298],[5.82,-0.298],[5.829,-0.288],[6.992,-0.288],[7.001,-0.279],[9.538,-0.27],[9.547,-0.279],[9.583,-0.279],[9.666,-0.307],[9.684,-0.325],[9.702,-0.325],[9.73,-0.343],[9.766,-0.38],[9.803,-0.38],[9.812,-0.389],[9.849,-0.389],[9.867,-0.38],[9.876,-0.389],[9.95,-0.389],[9.972,-0.357],[9.963,-0.348],[9.963,-0.321],[9.977,-0.307],[9.995,-0.316],[11.094,-0.316],[11.158,-0.279],[11.222,-0.27],[11.232,-0.261],[15.838,-0.261],[15.847,-0.27],[15.939,-0.279],[15.994,-0.298],[16.039,-0.325],[16.168,-0.325],[16.19,-0.284],[16.195,-0.243],[16.232,-0.243],[16.241,-0.252],[16.25,-0.243],[16.259,-0.261],[16.277,-0.261],[16.287,-0.243],[16.314,-0.261],[16.323,-0.243],[16.332,-0.261],[16.351,-0.261],[16.36,-0.243],[16.378,-0.261],[16.396,-0.243],[16.406,-0.261],[16.415,-0.261],[16.433,-0.243],[16.438,-0.256],[16.451,-0.261],[16.47,-0.243],[16.479,-0.261],[16.488,-0.261],[16.506,-0.243],[16.516,-0.261],[16.543,-0.252],[16.561,-0.261],[16.58,-0.243],[16.589,-0.261],[16.607,-0.252],[16.635,-0.261],[16.653,-0.252],[16.671,-0.261],[16.69,-0.252],[16.708,-0.261],[16.726,-0.252],[16.744,-0.261],[16.763,-0.252],[16.781,-0.261],[16.804,-0.243],[16.804,0.22],[16.763,0.234],[16.735,0.224],[16.717,0.234],[16.708,0.224],[16.68,0.234],[16.662,0.224],[16.644,0.234],[16.635,0.224],[16.607,0.234],[16.598,0.224],[16.57,0.234],[16.561,0.224],[16.534,0.234],[16.525,0.224],[16.497,0.234],[16.488,0.224],[16.461,0.234],[16.451,0.224],[16.424,0.234],[16.415,0.224],[16.387,0.234],[16.378,0.224],[16.351,0.234],[16.342,0.224],[16.323,0.234],[16.305,0.224],[16.277,0.234],[16.222,0.206],[16.204,0.206],[16.19,0.22],[16.19,0.266],[16.168,0.298],[16.039,0.298],[16.021,0.279],[15.948,0.252],[15.847,0.243],[15.838,0.234],[15.059,0.234],[15.05,0.243],[14.913,0.234],[14.904,0.243],[11.25,0.243],[11.241,0.252],[11.204,0.252],[11.149,0.27],[11.076,0.307],[10.005,0.307],[9.977,0.298],[9.963,0.311],[9.959,0.371],[9.785,0.371],[9.739,0.334],[9.666,0.298],[9.647,0.298],[9.592,0.27],[9.501,0.261],[9.492,0.252],[9.455,0.252],[9.446,0.261],[9.391,0.252],[9.382,0.261],[8.246,0.261],[8.237,0.27],[6.342,0.279],[6.332,0.288],[5.169,0.288],[5.16,0.298],[2.898,0.307],[2.889,0.316],[2.825,0.316],[2.779,0.334],[2.724,0.334],[2.715,0.343],[2.679,0.343],[2.624,0.362],[2.578,0.362],[2.569,0.371],[2.523,0.371],[2.514,0.38],[2.459,0.38],[2.413,0.398],[2.367,0.398],[2.312,0.417],[2.212,0.426],[2.157,0.444],[2.056,0.453],[2.01,0.472],[1.909,0.481],[1.9,0.49],[1.259,0.49],[1.236,0.531],[1.236,0.549],[1.204,0.582],[1.076,0.582],[1.053,0.559],[1.039,0.508],[0.92,0.508],[0.884,0.49],[0.865,0.499],[0.856,0.49],[0.517,0.49],[0.462,0.49],[0.453,0.499],[0.444,0.49],[0.435,0.499],[0.426,0.49],[0.417,0.499],[0.408,0.49],[0.334,0.49],[0.325,0.499],[0.316,0.49],[0.307,0.499],[0.298,0.49],[0.288,0.499],[0.279,0.49],[0.27,0.499],[0.261,0.49],[0.188,0.49],[0.179,0.499],[0.169,0.49]],"scaleRefs":["faxon-16-pencil-barrel.flange_od"],"inputs":{"faxon-16-pencil-barrel.flange_od":1.163,"faxon-16-pencil-barrel.outline_front_face":16.804,"faxon-16-pencil-barrel.outline_rear_face":0.103},"tolerance":0.006,"photo":"references/faxon-16-pencil-barrel f09ad3b5be48 (Primary Arms' gallery, 15A58M16NPQ_01: the barrel level on white, the muzzle at the right, 2000 x 1333)","method":"luminance < 235, 1 boxes excluded, largest piece, holes filled; scale from faxon-16-pencil-barrel.flange_od = 1.163 in (y-extent 127 px → 109.2 px/in); origin at x min, y center of the outline; clipped to x min {.outline_rear_face} = 0.103, x max {.outline_front_face} = 16.804; Douglas-Peucker at 0.006 in with the extremes kept: 240 points (IoU 0.997 with the full outline); The index pin (columns 176 to 188 of the upper edge) is boxed out: it is a pin, not a ring. The thread is left as the silhouette has it (its teeth a pixel deep): the model draws the thread itself.; checks: centre between the top (max over 0.4 in windows) along x [2.9, 9.2] 0.000 ± 0.027; centre between the top (max over 0.4 in windows) along x [11.4, 15.6] -0.009 ± 0.027; height (tooth tops, max over 0.02 in windows) along x [10.0, 10.9] 0.623 ± 0.028; height (tooth tops, max over 0.02 in windows) along x [11.4, 15.6] 0.504 ± 0.028; height (tooth tops, max over 0.02 in windows) along x [1.3, 1.8] 0.971 ± 0.028; height (tooth tops, max over 0.02 in windows) along x [9.78, 9.9] 0.759 ± 0.028 (tools/trace.py)","via":"harvest","note":"Black on white, cut out: the outline is the silhouette's at grey 235, at the photo's one scale. Each face's corner is rounded by its rim's arc (the lens sees the ends from 12° off square): by 0.06 in at the flange and 0.04 at the muzzle shoulder; the model squares each at the ledger's face."}},"gaps":[{"what":"The section ahead of the gas block: .525 by Faxon's sentence, .50 by both photographs","need":"Faxon's print (its page says its figures are from it and doesn't publish it), or a caliper reading on a barrel; until then the photographs' figure is drawn and the maker's kept beside it (forward_od)"},{"what":"Where the 16.13 in is measured from","need":"Faxon's statement. Taken from the barrel's breech end (as the Army's drawing dimensions a barrel), three other published sizes land within a hundredth on the photo; from either of the two other faces they miss by 2 to 3%"},{"what":"The collar behind the journal and the long taper's two diameters","need":"Faxon's print: its sentence gives the journal and names a tapered body, no collar and no figures for the taper; they are the photo's (± 0.009 in)"},{"what":"The gas port's distance from the breech","need":"Faxon's figure (its page says only that mid-length gas \"puts the port about two inches farther from the chamber than carbine-length gas\"); it is read on an oblique close view, ± 0.04 in"},{"what":"The gas port's diameter: .081 by Faxon, .078 by Primary Arms and Impact Guns","need":"Nothing drawn turns on it; Faxon's own page is taken (gas_port_d keeps all three)"},{"what":"The target crown's width and depth, the extension's locking lugs and feed ramps, the chamber","need":"A straight view of the muzzle's face with a scale in its plane; the extension's drawing (8448550 isn't in the package)"}]},"fn-p90-50-magazine":{"id":"fn-p90-50-magazine","name":"PS90/P90 5.7x28mm Magazine, 50-round","manufacturer":"FN America","sku":"3810110093","url":"https://www.kygunco.com/product/fnh-usa-3810110093-ps90-5.7x28-50rd-smoke-finish-magazine","category":"magazine","description":"FN's 50-round magazine for the P90 and the PS90, in 5.7x28mm: a long, flat, translucent box laid along the top of the rifle, its rounds lying across it in two rows and turned through the black feed tower at its rear end to face the chamber. The AR57 upper takes it the same way, on top.","weight":"fn-p90-50-magazine.weight","cartridge":{"takes":["5.7x28mm"],"stated":"e. 5.7x28mm Magazine Product No: 3810110093 (50-round) Product No: 3816101050 (30-round) Product No: 3816101040 (10-round)","source":"https://web.archive.org/web/20110711014348/http://fnhusa1.com/PDF/2009FNHUSAcatalog.pdf (FNH USA's 2009 catalog, its PS90/P90 accessories; as cached: references/fn-p90-50-magazine/docs/b3fed823b9.pdf)"},"rounds":{"capacity":"fn-p90-50-magazine.capacity","each":"fn-p90-50-magazine.round_weight"},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"feed":{"origin":[0,0,0],"note":"Where a seated magazine's own frame stands on the upper: its rear end (the round end's rearmost point, at the tower's back) and its underside (the body's flat face round the tower, which lies on the upper), on the centre plane. The upper's `magazine_feed` anchor is the same point read on the upper (each part carries its own half of the seat)."}},"interfaces":{"feed":{"type":"p90_magazine","role":"magazine","anchor":"feed","params":{},"flips":false}},"materials":{"body":{"label":"Magazine body","finish":"translucent_polymer","recolorable":false,"color":"fn-smoke","options":{"smoke":{"label":"Smoke","finish":"translucent_polymer","color":"fn-smoke","sku":"3810110093","source":"https://www.kygunco.com/product/fnh-usa-3810110093-ps90-5.7x28-50rd-smoke-finish-magazine"}},"default":"smoke","note":"One colourway: FN's catalog \"MAGAZINE Translucent polymer body\" (FN America's PS90 page); KYGUNCO \"This magazine is made of polymer and comes in a translucent smoke finish\"; Blackstone \"Smoke Polymer\". Midwest Gun Works lists the same number as \"Finish / Color: Black\" over a photo of the smoke one (128e601bf5c7): one product. The front cap is the body's moulding and colour in every photo (0db3af782b2b, 785f74cccd90, 054c636f9e79). The rounds, the spring and the follower seen through it aren't drawn."},"tower":{"label":"Feed tower","finish":"polymer","recolorable":false,"color":"placeholder-polymer-black","sheen":"matte","note":"The rotary feed's cap at the rear end, a matte black polymer in every photo of it (785f74cccd90, ed67cb0af658, 128e601bf5c7): the same in the one colourway. A black: not fitted to a photo."}},"components":{"body":{"label":"Body and front cap","material":"body"},"tower":{"label":"Feed tower","material":"tower"}},"geometry":{"model":"fn-p90-50-magazine.glb","components":{},"approximations":["Its sizes are read on photos, no page giving any: its length and height on Primary Arms' side photo of it on the AR57 upper, scaled by the receiver's Picatinny rail (the M-LOK slots agree within 0.3%; the 12 in upper's photo, by its own rail, reads the length 10.98, 0.06 more); its width on Blackstone's view of its top face and its feed tower on Blackstone's side view, each scaled by that length. Wikipedia's P90 render reads its height 0.1 in more (kept in the ledger).","A long box with soft long edges (an assumed round of 0.15 in, the patent's section at a glance), its rear end a half round about the feed tower's axis in plan (US 4,905,394's FIG. 3 and FIG. 4, and every photo from below), the tower a cylinder concentric with that end standing 0.48 in below the underside. Inside the round end the tower's black is carried up to nine tenths of the body's height (a ratio, not a reading: Primary Arms' photo on the AR57 shows black through the smoke there nearly to the top), and the body is cut where it stands, so the two don't share space.","Seated on the AR57 (054c636f9e79) the tower shows through a notch in the receiver's near wall 1.52 in long (the upper's feed_notch_length): the chord its round pocket cuts in the wall, not the tower, which Blackstone's view of the magazine alone has 1.90 across, its rear at the body's rear end (US 4,905,394's FIG. 7 draws it flush). On the 16 in's photo the notch's middle is the tower's centre within 0.04 in; on the 12 in's it is 0.13 behind it (said to the upper's owner, 2026-10-18). Whatever the two models share is held by the test to the tower and the other pieces under the underside, and to the cap's face.","The rear end's catch notch, where the upper's latch bears (the AR57 photo has a black latch against the rear end over its lower half), isn't drawn: Blackstone's side view has a dent there of 2 px, 0.05 in, and no view shows it square.","The front cap: a band round the front end 0.45 in long, 0.05 in proud of each side, 0.17 in above the top and 0.22 below the underside, with its two latch lugs on top at the sides reaching back 0.6 in from its face (their width across assumed: a quarter of the cap each, as Blackstone's view of the top shows them). Under the underside the band is two feet at its corners with its middle up at the underside, as the views from below show them (79ffb375bc2f, 128e601bf5c7: rounded knobs at the corners, about a third of the width each at a glance; drawn as wide as the lugs), each foot's back sloping up behind the band at 48 degrees (the AR57 photo's silhouette: 10 px up over 9 back). In each side of the cap a panel recessed 0.02 in (assumed: no view has it in profile) inside a frame 0.07 wide at its front and over it, open at the band's rear edge and down to the underside, as the AR57 photo shows it square on (a 10x crop of 735 to 805 px). The two dark windows at the panel's inner corners (the lugs' undercuts, a few hundredths across) aren't drawn.","The rib across the underside right behind the cap (detail pass, 2026-10-18): a half-round bar 0.25 in along, 0.08 below the underside, its front edge 0.55 behind the cap's face (all three on the AR57 photo's silhouette, where it shows as a bump under the front end clear of the handguard's top), 1.5 in across with round ends (assumed: about three quarters of the face's width on two oblique views from below). Its section is drawn as a half ellipse; the photos show a rounded bar.","The tower's bottom face: a bar along the magazine with the slot the top round lies in (as wide as a 5.7x28 case, 0.313 in), between two D-shaped pockets inside a rim (the bar's width, the pockets' depth and the rim's width assumed: 0.72, 0.12 and 0.12 in); the slot as deep as it is wide (the round lies in it with its top about level with the lips, ed67cb0af658).","Drawn as one tinted volume, as the translucent finish draws every smoke magazine, empty, as it is sold (what fifty rounds weigh is counted by `rounds`, not drawn). What shows through it in the photos and is drawn: the rotary feed's black housing inside the round end (the tower carried up into it). What shows through and isn't: the rounds (only the loaded photos have them); the spring, a fine wire zig-zag (US 4,905,394's FIG. 3 and FIG. 19; seen through the top on Blackstone's 0db3af782b2b and as lines across the side on the AR57 photo, about 0.66 in apart), whose form in depth only the patent's embodiment gives and which would be a hairline at the page's size; the follower; and the window-like frame along each side, the inner guides of the patent's FIG. 8 section (its 23 and 24) seen through a wall whose outside the same figure draws plain.","Not drawn, its relief unread: two long lines down the top face about 0.55 in either side of the centre line (Blackstone's top view 0db3af782b2b, as two lines the whole length that the spring's zig-zag turns between; Primary Arms' view from ahead and above, references/panzer-ar57-ult-16-upper b894132847e8, as two crisp dark lines with a lit edge ending short of the cap with round ends; Blackstone's side view from above, 76c0d7572a37, the same). They are either grooves in the top face or the patent's two inner ribs on the top wall (FIG. 8's 21) seen through it: no view meets them at an edge, so whether they are cut into the face isn't read.","Not drawn on the outside: the round counter's ticks and numbers and the two long index lines down the underside, the \"5.7x28\" and the maker's mark moulded there (lettering, and on the face that lies on the upper).","The raised ring with its bore on the underside just ahead of the tower (ed67cb0af658, 9516509da8f4, 128e601bf5c7, 79ffb375bc2f): drawn on the centre line with its edge at the tower's, as the close views from below have it (between the two index lines near their middle, nearly touching the tower), its sizes all assumed at a glance against the tower (0.45 in across, a 0.3 bore 0.1 deep, 0.03 proud). It lies on the upper's top just ahead of the feed pocket, where no photo shows what the upper has under it."],"ledger":["fn-p90-50-magazine.length","fn-p90-50-magazine.width","fn-p90-50-magazine.height","fn-p90-50-magazine.tower_d","fn-p90-50-magazine.tower_drop","fn-p90-50-magazine.cap_length","fn-p90-50-magazine.cap_above","fn-p90-50-magazine.cap_below","fn-p90-50-magazine.cap_lug_length","fn-p90-50-magazine.cap_width","fn-p90-50-magazine.cap_lug_width","fn-p90-50-magazine.cap_foot_slope","fn-p90-50-magazine.cap_panel_frame","fn-p90-50-magazine.cap_panel_depth","fn-p90-50-magazine.rib_from_face","fn-p90-50-magazine.rib_length","fn-p90-50-magazine.rib_drop","fn-p90-50-magazine.rib_span","fn-p90-50-magazine.ring_od","fn-p90-50-magazine.ring_id","fn-p90-50-magazine.ring_height","fn-p90-50-magazine.ring_bore_depth","fn-p90-50-magazine.edge_radius","fn-p90-50-magazine.lip_bar_width","fn-p90-50-magazine.slot_width","fn-p90-50-magazine.pocket_depth","fn-p90-50-magazine.pocket_rim"]},"profiles":{},"gaps":[{"what":"Every size of it: no page (FN's, a seller's, a review's) gives one","need":"FN's or a seller's figures, or a square view from the side, the top and an end with a scale in the part's plane"},{"what":"Its weight empty (worked out from Wikipedia's two weights of a P90, ± 1.7 oz)","need":"FN's figure, or a review's weighing"},{"what":"The feed tower's bottom face (its bar and pockets) and the cap's lugs and feet in profile","need":"A view of the feed end square from below and one of the front end square on"},{"what":"The raised ring on the underside: where it stands across, its size and how far it stands proud (all assumed)","need":"A view of the underside square on, with the tower in it, and one of the ring in profile"},{"what":"The two long lines down the top face: grooves in it, or inner ribs seen through it","need":"A view along the top face at a grazing angle, or one of the front or rear end square on, where a groove would notch the outline"}]},"geissele-139-chf-barrel":{"id":"geissele-139-chf-barrel","name":"CHF Chrome Lined Barrel - 5.56 - 13.9\"","manufacturer":"Geissele Automatics","sku":"05-2989","url":"https://www.primaryarms.com/geissele-automatics-5-56-chf-mid-length-taper-profile-ar-15-barrel-chrome-lined-13-9in","category":"barrel","description":"Geissele's 13.9 in cold-hammer-forged 5.56 barrel, stripped, in its taper profile: chrome lined, 1:7 twist, manganese phosphate, a mid-length gas port (.081) on a .750 in journal with a dimple under it for a gas block's set screw, an M4 feed ramp extension, a 1/2 x 28 muzzle thread. Sellers' pages: \"This 13.9\" cold hammer-forged barrel features a mid-length gas system and a 1:7 twist rate\" (Primary Arms); \".750\" gas block diameter with a precision-machined dimple for secure mounting\" and \"High Pressure Tested (HPT) and Magnetic Particle Inspected (MPI)\" (Huckleberry Arms). Its steel is stated three ways: \"Chrome Moly Vanadium Steel\" (Huckleberry Arms, Rooftop Defense, Kenzie's Optics), \"Chromoly steel construction\" and \"Barrel Material Steel\" (Primary Arms), \"Material Chromolly Steel\" (AR15Discounts, Dirty Bird).","weight":"geissele-139-chf-barrel.weight","barrelLength":"geissele-139-chf-barrel.length","cartridge":{"takes":["5.56 NATO"],"stated":"Chambered in 5.56 NATO, 1:7 twist","source":"https://www.primaryarms.com/geissele-automatics-5-56-chf-mid-length-taper-profile-ar-15-barrel-chrome-lined-13-9in (the seller's feature list for 05-2989, as cached: harvest.quote; Huckleberry Arms' table has \"Caliber 5.56 NATO\", Rooftop Defense's \"Chamber: 5.56NATO\"; Geissele's own site refuses the reader and is left alone)"},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"extension":{"origin":[0,0,0],"note":"The barrel extension's flange, its rear face, on the bore axis, +x toward the muzzle."},"muzzle":{"origin":["{.shoulder_x}",0,0]},"gas_journal":{"origin":["{.gas_port_x}",0,0]}},"interfaces":{"barrel_extension":{"type":"ar15.barrel_extension","role":"barrel","anchor":"extension","params":{},"flips":false,"note":"Huckleberry Arms: \"Barrel Extension M4 Feedramps\"; Primary Arms: \"M4 feed ramps\" and \"Feed Ramps M4\"."},"muzzle":{"type":"muzzle_thread","role":"barrel","anchor":"muzzle","params":{"thread":"1/2-28","thread_length":"={.thread_length}"},"flips":false,"note":"The sellers' statement: Primary Arms \"Threaded 1/2x28\" and \"Thread Pattern 1/2 X 28\", Huckleberry Arms \"Muzzle Thread Pitch 1/2 x 28\". Its length is read off the photo (0.62 ± 0.03 in; the Army barrel's is .63). No muzzle device comes with it."},"gas_journal":{"type":"ar15.gas_journal","role":"barrel","anchor":"gas_journal","params":{"journal_od":"={.journal_od}"},"flips":false,"note":"Primary Arms: \".750\" gas block diameter, .081\" gas port\" and \"Gas Seat Diameter .750\"; Huckleberry Arms: \"Gas Block Diameter .750\"\", \"Gas Port .081\" and \".750\" gas block diameter with a precision-machined dimple for secure mounting\". The journal runs from 8.89 to 9.93 in ahead of the receiver's face, a collar behind it; the port, which the photo shows, is 0.29 in ahead of the collar's face."},"gas_system":{"type":"ar15.gas_system","role":"barrel","params":{"length":"mid"},"flips":false,"note":"Primary Arms: \"Mid-length gas system\" and \"Gas System Length Mid-Length\"; Huckleberry Arms: \"Gas Length Mid-Length\"; Rooftop Defense: \"Gas System Length: Midlength\"; AR15Discounts, Dirty Bird, Kenzie's Optics and C. Stephens the same. (One review of Geissele's 13.9 in Super Duty upper, another product with another barrel, says \"carbine-length gas system\": Defense Distributors; the seller of that upper says \"GAS LENGTH: Mid-Length\" too.) What the platform checks a gas tube against a barrel by (D83)."}},"materials":{"barrel":{"label":"Barrel","finish":"phosphate","recolorable":false,"color":"geissele-barrel-phosphate","note":"Primary Arms: \"manganese phosphate finish\" and \"Barrel Coating Manganese Phosphate\"; Huckleberry Arms: \"Finish Manganese Phosphate\"; Rooftop Defense: \"Finish: Chrome-lined, Phosphate\". The one finish this number is sold in: no colourways. Its colour is fitted to Primary Arms' photos of this barrel and of the 14.5 in one (geissele-barrel-phosphate: about nine levels darker than BCM's barrel in the same studio). One slot: in Primary Arms' photos the extension, its index pin, the journal and the thread are the barrel's own matte charcoal (#373737 along the taper and whole in its side view, aaf30d1a864c; #323232 in its three-quarter view). Not drawn: the chrome of the bore and the chamber (inside), Geissele's G behind the muzzle ring and the line of marking ahead of the chamber (printed)."}},"components":{},"geometry":{"model":"geissele-139-chf-barrel.glb","components":{},"approximations":["Turned station by station from figures read off Primary Arms' side photo of this barrel (05-2989_02), extension to muzzle. That photo is a close one and yawed (the muzzle end nearer the lens: 2% in scale end to end), so its diameters are read at a scale that runs in a line along it between two sizes known at its two ends, the published .750 journal and the Army's .999 extension, and its lengths through the same line, stretched to the published 13.9 in (from its breech end, with the extension's half inch behind that: 14.40 end to end; the photo's own scales make it 1.2% shorter).","Straight between its stations: the chamber section, a cone, the long taper (the \"Geissele Taper Profile\": 0.726 in down to 0.665 over six inches, one straight line on both edges of the photo), the gas block journal, a cone, the muzzle section, the ring behind the shoulder. The one curve, the flare from the taper up to the collar behind the journal, is a smooth cubic through the traced outline. Every face is square at its station; the photo rounds each corner by its rim's arc, and their real edge breaks aren't drawn.","The gas port at its published .081, where the photo shows it (0.29 in ahead of the collar). The indexing pin at the Army drawing's diameter, where the photo has it against the flange's rear face, as high as the Army's limit (.094): the photo looks down on it. The bore one plain hole right through, at the Army drawing's .219; the extension's rear opening turned at the reference CAD set's sizes for a mil-spec M4 extension (its chamfered mouth, the ring its locking lugs make, the recess ahead of them).","The muzzle thread is a helix, 28 to the inch, between the minor and major diameters of the Army barrel's 1/2-28 thread (the sellers state 1/2 x 28): a plain V without the flats of its form, right-hand (assumed: its designation marks no other), running out at the shoulder over its last pitch, with no relief there, no chamfer and no crown at the muzzle.","Not drawn: the dimple under the journal (its depth isn't sourced), the slot along the collar's top in line with the port (a sixteenth of an inch wide by the photo; its depth isn't sourced), the relief at the foot of the collar's front face, the chamber, the slots between the extension's locking lugs and its feed ramps (the lugs are one ring), the G and the marking."],"ledger":["geissele-139-chf-barrel.length","geissele-139-chf-barrel.overall_length","geissele-139-chf-barrel.extension_rear_x","geissele-139-chf-barrel.flange_front_x","geissele-139-chf-barrel.taper_rear_od","geissele-139-chf-barrel.taper_front_od","geissele-139-chf-barrel.journal_rear_x","geissele-139-chf-barrel.gas_port_x","geissele-139-chf-barrel.journal_od","geissele-139-chf-barrel.shoulder_x","geissele-139-chf-barrel.thread_length","geissele-139-chf-barrel.muzzle_od"]},"profiles":{"side":{"plane":"xy","origin":"the silhouette's rear tip, on the axis; the outline begins at the extension's rear face","offset":{"x":"extension_rear_x"},"points":[[0.184,0.483],[0.184,-0.497],[0.983,-0.497],[0.99,-0.49],[1.041,-0.49],[1.088,-0.551],[1.127,-0.576],[1.264,-0.576],[1.307,-0.555],[1.365,-0.483],[1.984,-0.49],[1.992,-0.483],[2.1,-0.483],[2.172,-0.468],[2.258,-0.468],[2.381,-0.447],[2.445,-0.447],[2.453,-0.439],[2.64,-0.432],[2.647,-0.425],[2.87,-0.411],[2.928,-0.396],[2.993,-0.396],[3,-0.389],[3.324,-0.367],[3.331,-0.36],[3.439,-0.36],[3.447,-0.353],[7.329,-0.339],[7.336,-0.331],[8.359,-0.331],[8.366,-0.324],[8.424,-0.324],[8.431,-0.331],[9,-0.331],[9.008,-0.324],[9.188,-0.324],[9.195,-0.331],[9.288,-0.331],[9.296,-0.339],[9.368,-0.339],[9.375,-0.346],[9.519,-0.36],[9.721,-0.418],[9.879,-0.418],[9.908,-0.367],[11.017,-0.375],[11.024,-0.367],[11.168,-0.36],[11.176,-0.353],[11.478,-0.346],[11.485,-0.339],[12.847,-0.339],[12.861,-0.331],[12.868,-0.339],[13.473,-0.339],[13.524,-0.353],[13.79,-0.36],[13.823,-0.335],[13.844,-0.285],[13.87,-0.259],[13.891,-0.252],[13.956,-0.252],[13.963,-0.259],[13.97,-0.252],[13.985,-0.259],[14.129,-0.252],[14.136,-0.259],[14.23,-0.259],[14.237,-0.252],[14.251,-0.259],[14.259,-0.252],[14.302,-0.252],[14.309,-0.259],[14.395,-0.259],[14.406,-0.252],[14.406,0.234],[14.388,0.245],[13.891,0.245],[13.87,0.252],[13.837,0.285],[13.823,0.328],[13.805,0.346],[13.553,0.346],[13.488,0.331],[11.86,0.339],[11.853,0.331],[11.774,0.331],[11.766,0.339],[11.471,0.339],[11.464,0.346],[11.082,0.367],[11.075,0.375],[9.915,0.382],[9.908,0.375],[9.897,0.407],[9.879,0.425],[9.728,0.425],[9.526,0.367],[9.382,0.353],[9.375,0.346],[9.288,0.346],[9.281,0.339],[6.926,0.346],[6.919,0.353],[5.161,0.353],[5.154,0.36],[3.447,0.36],[3.439,0.367],[3.324,0.367],[3.317,0.375],[3.007,0.396],[2.928,0.411],[2.784,0.418],[2.777,0.425],[2.705,0.425],[2.698,0.432],[2.611,0.432],[2.539,0.447],[2.381,0.454],[2.373,0.461],[2.273,0.461],[2.265,0.468],[2.136,0.475],[2.064,0.49],[1.372,0.483],[1.286,0.569],[1.264,0.576],[1.134,0.576],[1.098,0.555],[1.048,0.49],[0.846,0.49],[0.191,0.49]],"scaleRefs":["geissele-139-chf-barrel.outline_flange_od"],"inputs":{"geissele-139-chf-barrel.outline_flange_od":1.1525,"geissele-139-chf-barrel.outline_front_face":14.406,"geissele-139-chf-barrel.outline_rear_face":0.184},"tolerance":0.006,"photo":"references/geissele-139-chf-barrel aaf30d1a864c (Primary Arms' gallery, 05-2989_02: the barrel level on white, the muzzle at the right, 2200 x 1467)","method":"luminance < 235, largest piece, holes filled, notches filled in [2008, 670, 2110, 795] (disk closing, r 6 px); scale from geissele-139-chf-barrel.outline_flange_od = 1.1525 in (y-extent 160 px → 138.8 px/in); origin at x min, y center of the outline; clipped to x min {.outline_rear_face} = 0.184, x max {.outline_front_face} = 14.406; Douglas-Peucker at 0.006 in with the extremes kept: 133 points (IoU 0.997 with the full outline); The thread's teeth are filled to their crests: the model draws the thread itself.; checks: centre between the top (max over 0.4 in windows) along x [2.6, 8.0] 0.007 ± 0.022; centre between the top (max over 0.4 in windows) along x [10.9, 12.4] 0.004 ± 0.022; height (tooth tops, max over 0.02 in windows) along x [10.0, 10.8] 0.756 ± 0.022; height (tooth tops, max over 0.02 in windows) along x [0.3, 0.9] 0.987 ± 0.022 (tools/trace.py)","via":"harvest","note":"Black on white, cut out: the outline is the silhouette's at grey 235, at the journal's scale throughout. NOT to scale away from the journal: the photo is yawed, and the extension reads .985 for .999 (outline_extension_od). The model corrects it; its figures are the ledger's. Each face's corner is rounded by its rim's arc (the lens sees the ends from 20° off square)."}},"gaps":[{"what":"Every diameter but the journal's, and every station along the barrel","need":"Geissele's own page or drawing (its site refuses the reader): all are read off one seller's close, yawed photo at 139 px to the inch, through a scale fixed at two stations: ± 0.008 in on a diameter and ± 0.03 to 0.04 on a station. A level photo taken from further off would do better"},{"what":"Where the 13.9 in is measured from","need":"The maker's statement (taken from the barrel's breech end, as the Army's drawing dimensions a barrel; the photo by its own scales reads 0.18 in shorter end to end, which is nearer what a length from the bolt's face would be)"},{"what":"The dimple under the journal: its place and depth; the slot along the collar: its depth","need":"Geissele's figures, or a level view of the underside and a close view of the collar's top with their edges on the silhouette"},{"what":"The extension's locking lugs and feed ramps, the chamber's mouth, the muzzle's crown","need":"The extension's drawing (8448550 isn't in the package) and a close view of the muzzle: the extension's inside is the reference CAD set's, turned; hidden once the barrel is in a receiver"},{"what":"Its steel","need":"The maker's own statement: sellers print \"Chrome Moly Vanadium Steel\", \"Chromoly steel\", \"Chromolly Steel\" and \"Steel\""}]},"geissele-145-chf-barrel":{"id":"geissele-145-chf-barrel","name":"CHF Chrome Lined Barrel - 5.56 - 14.5\"","manufacturer":"Geissele Automatics","sku":"05-2985","url":"https://www.primaryarms.com/geissele-automatics-5-56-chf-mid-length-taper-profile-ar-15-barrel-chrome-lined-14-5in","category":"barrel","description":"Geissele's 14.5 in cold-hammer-forged 5.56 barrel, stripped, in its taper profile: chrome lined, 1:7 twist, manganese phosphate, a mid-length gas port (.076) on a .750 in journal with a dimple under it for a gas block's set screw, an M4 feed ramp extension, a 1/2 x 28 muzzle thread. Sellers' pages: \"This cold hammer-forged 14.5\" barrel features a Geissele Taper Profile and mid-length gas system\" (Primary Arms); \"Geissele barrels are High Pressure Tested (HPT) and Magnetic Particle Inspected (MPI)\" (Mile High). Its steel is stated three ways: \"Chrome moly vanadium steel\" (Primary Arms' features, Mile High, Rooftop Defense), \"Barrel Material 4140 Chrome Moly Steel\" (Primary Arms' table) and, for a listing under another number, \"4150 CMV Steel\" (Charlie's Custom Clones, 05-1861).","weight":"geissele-145-chf-barrel.weight","barrelLength":"geissele-145-chf-barrel.length","cartridge":{"takes":["5.56 NATO"],"stated":"Chambered in 5.56 NATO","source":"https://www.primaryarms.com/geissele-automatics-5-56-chf-mid-length-taper-profile-ar-15-barrel-chrome-lined-14-5in (the seller's feature list for 05-2985, as cached: harvest.quote; Mile High's table has \"CHAMBER: 5.56\", Rooftop Defense's \"Chamber: 5.56NATO\"; Geissele's own site refuses the reader and is left alone)"},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"extension":{"origin":[0,0,0],"note":"The barrel extension's flange, its rear face, on the bore axis, +x toward the muzzle."},"muzzle":{"origin":["{.shoulder_x}",0,0]},"gas_journal":{"origin":["{.gas_port_x}",0,0]}},"interfaces":{"barrel_extension":{"type":"ar15.barrel_extension","role":"barrel","anchor":"extension","params":{},"flips":false,"note":"Mile High: \"BARREL EXTENSION: M4 Feedramps\"; Primary Arms: \"Feed Ramps M4\"."},"muzzle":{"type":"muzzle_thread","role":"barrel","anchor":"muzzle","params":{"thread":"1/2-28","thread_length":"={.thread_length}"},"flips":false,"note":"The sellers' statement: Primary Arms \"Threaded 1/2x28\" and \"Thread Pattern 1/2 X 28\", Mile High \"MUZZLE THREAD: 1/2 x 28\". Its length is read off the photo (0.62 ± 0.03 in; the Army barrel's is .63). No muzzle device comes with it."},"gas_journal":{"type":"ar15.gas_journal","role":"barrel","anchor":"gas_journal","params":{"journal_od":"={.journal_od}"},"flips":false,"note":"Mile High: \"GAS BLOCK DIAMETER: .750\", \"GAS PORT: .076\" and \"There is one dimple machined in for a gas block set screw\"; Primary Arms: \"Gas Seat Diameter .750\". The journal runs from 8.88 to 9.93 in ahead of the receiver's face, a collar behind it; the port is taken to be over the dimple, 0.29 in ahead of the collar's face."},"gas_system":{"type":"ar15.gas_system","role":"barrel","params":{"length":"mid"},"flips":false,"note":"Mile High: \"GAS LENGTH: Mid-Length\"; Primary Arms: \"Gas System Length Mid-Length\" and \"Mid-Length gas system\"; Rooftop Defense: \"Gas System Length: Midlength\". What the platform checks a gas tube against a barrel by (D83)."}},"materials":{"barrel":{"label":"Barrel","finish":"phosphate","recolorable":false,"color":"geissele-barrel-phosphate","note":"Mile High: \"FINISH: Manganese Phosphate\"; Primary Arms: \"Manganese phosphate exterior finish\" and \"Barrel Coating Manganese Phosphate\"; Rooftop Defense: \"Finish: Chrome-lined, Phosphate\". The one finish this number is sold in: no colourways. Its colour is fitted to Primary Arms' photos of this barrel and of the 13.9 in one (geissele-barrel-phosphate: about nine levels darker than BCM's barrel in the same studio). One slot: in Primary Arms' photos the extension, the journal and the thread are the barrel's own matte charcoal (the extension reads #343232 beside the taper's #2f2f2f and the journal's #303030 in its side view, dc38f9181866); the index pin is on the far side in them and the same grey as the extension in Rooftop's rendering. Not drawn: the chrome of the bore and the chamber (inside), Geissele's G behind the muzzle ring and the line of marking ahead of the chamber (printed)."}},"components":{},"geometry":{"model":"geissele-145-chf-barrel.glb","components":{},"approximations":["Turned station by station from figures read off Primary Arms' side photo of this barrel (05-2985_02), extension to muzzle: its diameters at the scale its gas block journal's published .750 gives, its lengths at the scale the published 14.5 in gives (from its breech end, with the extension's half inch behind that: 15.00 end to end). With the photo's black edge read at grey 235 the two scales differ by 0.6%.","Straight between its stations: the chamber section, a cone, the long taper (the \"Geissele Taper Profile\": 0.725 in down to 0.663 over six inches, one straight line within 0.002 in on both edges of the photo), the gas block journal, a cone, the muzzle section, the ring behind the shoulder. The one curve, the flare from the taper up to the collar behind the journal, is a smooth cubic through the traced outline (0.0014 in rms). Every face is square at its station; the photo rounds each corner by its rim's arc, and their real edge breaks aren't drawn.","The gas port, at its published .076, is put at the station of the dimple under the journal, which is what the photo shows (the barrel lies with its underside toward the lens); Rooftop's rendering has the port itself 0.28 in ahead of the collar, the dimple is 0.29.","The indexing pin at the Army drawing's diameter, standing against the flange's rear face as Rooftop's rendering has it and as high as the Army's limit (.094): no photo of this barrel has the pin on its silhouette. The bore one plain hole right through, at the Army drawing's .219; the extension's rear opening turned at the reference CAD set's sizes for a mil-spec M4 extension (its chamfered mouth, the ring its locking lugs make, the recess ahead of them).","The muzzle thread is a helix, 28 to the inch, between the minor and major diameters of the Army barrel's 1/2-28 thread (the sellers state 1/2 x 28): a plain V without the flats of its form, right-hand (assumed: its designation marks no other), running out at the shoulder over its last pitch, with no relief there, no chamfer and no crown at the muzzle.","Not drawn: the dimple under the journal (0.16 in across by the photo; its depth isn't sourced), the notch in the collar's top in line with the port (a pixel or two wide in every picture on file), the relief at the foot of the collar's front face, the chamber, the slots between the extension's locking lugs and its feed ramps (the lugs are one ring), the G and the marking."],"ledger":["geissele-145-chf-barrel.length","geissele-145-chf-barrel.overall_length","geissele-145-chf-barrel.extension_rear_x","geissele-145-chf-barrel.flange_front_x","geissele-145-chf-barrel.taper_rear_od","geissele-145-chf-barrel.taper_front_od","geissele-145-chf-barrel.journal_rear_x","geissele-145-chf-barrel.gas_port_x","geissele-145-chf-barrel.journal_od","geissele-145-chf-barrel.shoulder_x","geissele-145-chf-barrel.thread_length","geissele-145-chf-barrel.muzzle_od"]},"profiles":{"side":{"plane":"xy","origin":"the silhouette's rear tip, on the axis; the outline begins at the extension's rear face","offset":{"x":"extension_rear_x"},"points":[[0.069,0.501],[0.069,-0.495],[0.869,-0.5],[0.877,-0.492],[1.019,-0.493],[1.03,-0.542],[1.048,-0.568],[1.086,-0.584],[1.13,-0.584],[1.153,-0.584],[1.194,-0.573],[1.217,-0.498],[1.228,-0.487],[2.067,-0.485],[2.074,-0.478],[2.306,-0.464],[2.314,-0.457],[2.441,-0.45],[2.448,-0.443],[2.606,-0.436],[2.613,-0.429],[2.838,-0.415],[2.845,-0.408],[2.913,-0.408],[2.92,-0.401],[3.167,-0.38],[3.175,-0.372],[3.369,-0.366],[3.377,-0.359],[4.567,-0.359],[4.574,-0.351],[5.195,-0.355],[5.203,-0.348],[5.839,-0.352],[5.847,-0.345],[6.438,-0.348],[6.445,-0.341],[7.081,-0.345],[7.089,-0.338],[7.725,-0.342],[7.733,-0.334],[9.304,-0.329],[9.312,-0.337],[9.371,-0.337],[9.379,-0.345],[9.558,-0.368],[9.752,-0.422],[9.887,-0.423],[9.917,-0.371],[11.018,-0.37],[11.025,-0.363],[11.1,-0.363],[11.107,-0.356],[11.437,-0.343],[11.444,-0.336],[11.527,-0.336],[11.534,-0.329],[12.514,-0.335],[12.522,-0.328],[13.854,-0.329],[14.056,-0.33],[14.108,-0.345],[14.355,-0.347],[14.389,-0.328],[14.404,-0.276],[14.431,-0.25],[14.453,-0.243],[14.513,-0.251],[14.566,-0.236],[14.573,-0.243],[14.603,-0.236],[14.625,-0.244],[14.633,-0.236],[14.64,-0.244],[14.67,-0.237],[14.693,-0.244],[14.708,-0.237],[14.715,-0.244],[14.745,-0.237],[14.768,-0.245],[14.775,-0.237],[14.783,-0.245],[14.813,-0.237],[14.835,-0.245],[14.85,-0.238],[14.857,-0.245],[14.887,-0.238],[14.91,-0.246],[14.925,-0.238],[14.94,-0.246],[14.979,-0.237],[14.979,0.24],[14.958,0.248],[14.898,0.241],[14.89,0.248],[14.868,0.241],[14.838,0.249],[14.831,0.241],[14.816,0.249],[14.801,0.242],[14.771,0.249],[14.763,0.242],[14.748,0.249],[14.718,0.242],[14.696,0.25],[14.688,0.242],[14.629,0.25],[14.614,0.243],[14.606,0.25],[14.546,0.243],[14.524,0.251],[14.509,0.243],[14.456,0.259],[14.449,0.251],[14.427,0.259],[14.401,0.285],[14.393,0.323],[14.367,0.349],[14.113,0.351],[14.075,0.336],[13.986,0.337],[13.978,0.329],[12.766,0.337],[12.758,0.329],[11.845,0.328],[11.838,0.335],[11.419,0.338],[11.411,0.346],[11.284,0.346],[11.277,0.354],[11.157,0.355],[11.149,0.362],[11.03,0.363],[11.022,0.371],[9.93,0.378],[9.915,0.37],[9.893,0.423],[9.75,0.424],[9.72,0.409],[9.541,0.365],[9.503,0.365],[9.406,0.343],[9.353,0.344],[9.346,0.336],[9.248,0.337],[9.241,0.33],[6.36,0.348],[6.352,0.341],[6.315,0.341],[6.308,0.348],[6.023,0.35],[6.016,0.343],[5.799,0.344],[5.761,0.344],[5.754,0.352],[4.833,0.358],[4.826,0.35],[4.661,0.351],[4.324,0.361],[4.317,0.354],[3.441,0.359],[3.434,0.367],[3.187,0.376],[3.18,0.383],[3.112,0.384],[3.105,0.391],[2.693,0.424],[2.686,0.431],[2.611,0.432],[2.604,0.439],[2.529,0.44],[2.522,0.447],[2.424,0.448],[2.417,0.456],[2.26,0.464],[2.252,0.472],[2.162,0.472],[2.088,0.488],[1.227,0.493],[1.201,0.564],[1.183,0.583],[1.063,0.584],[1.044,0.573],[1.029,0.543],[1.029,0.506],[0.995,0.495],[0.726,0.496],[0.696,0.504],[0.666,0.497],[0.614,0.497],[0.606,0.505],[0.576,0.497],[0.254,0.499],[0.247,0.507],[0.21,0.507]],"scaleRefs":["geissele-145-chf-barrel.flange_od"],"inputs":{"geissele-145-chf-barrel.flange_od":1.168,"geissele-145-chf-barrel.outline_front_face":14.979,"geissele-145-chf-barrel.outline_rear_face":0.069},"tolerance":0.006,"photo":"references/geissele-145-chf-barrel dc38f9181866 (Primary Arms' gallery, 05-2985_02: the barrel level on white, the muzzle at the left, 2200 x 1467)","method":"luminance < 235, largest piece, holes filled, notches filled in [90, 670, 186, 790] (disk closing, r 6 px); rotated -0.4° as declared; scale from geissele-145-chf-barrel.flange_od = 1.168 in (y-extent 156 px → 133.6 px/in); origin at x min, y center of the outline; clipped to x min {.outline_rear_face} = 0.069, x max {.outline_front_face} = 14.979; Douglas-Peucker at 0.006 in with the extremes kept: 195 points (IoU 0.996 with the full outline); The thread's teeth (columns 96 to 180) are filled to their crests: the model draws the thread itself.; checks: centre between the top (max over 0.4 in windows) along x [2.6, 8.0] 0.002 ± 0.022; centre between the top (max over 0.4 in windows) along x [10.8, 13.0] 0.002 ± 0.022; height (tooth tops, max over 0.02 in windows) along x [10.0, 10.8] 0.748 ± 0.023; height (tooth tops, max over 0.02 in windows) along x [11.8, 13.6] 0.664 ± 0.023; height (tooth tops, max over 0.02 in windows) along x [0.3, 0.9] 0.996 ± 0.023 (tools/trace.py)","via":"harvest","note":"Black on white, cut out: the outline is the silhouette's at grey 235. Its diameters are at the journal's scale; its length is stretched to the published one by the model. Each face's corner is rounded by its rim's arc (the lens sees the ends from 9° and 13° off square): by 0.05 in at the flange and at the muzzle shoulder, 0.02 at the collar; the model squares those three at the ledger's faces."}},"gaps":[{"what":"Every diameter but the journal's, and every station along the barrel","need":"Geissele's own page or drawing (its site refuses the reader): all are read off one seller's photo at 133 px to the inch, ± 0.007 in on a diameter and ± 0.03 on a station"},{"what":"Where the 14.5 in is measured from","need":"The maker's statement (taken from the barrel's breech end, as the Army's drawing dimensions a barrel; the photo at its journal's scale reads 0.09 in shorter end to end, which is about what a length from the bolt's face would be)"},{"what":"The gas port's own station","need":"A straight view of the barrel's top with a scale in its plane: it is drawn over the dimple, which Rooftop's rendering agrees with to 0.03 in"},{"what":"The dimple under the journal: its depth; the notch in the collar: its width and depth","need":"Geissele's figures, or a close view of each with its edge on the silhouette"},{"what":"The extension's locking lugs and feed ramps, the chamber's mouth, the muzzle's crown","need":"The extension's drawing (8448550 isn't in the package) and a close view of the muzzle: the extension's inside is the reference CAD set's, turned; hidden once the barrel is in a receiver"},{"what":"Its steel","need":"The maker's own statement: sellers print \"Chrome moly vanadium steel\", \"4140 Chrome Moly Steel\" and (under another number) \"4150 CMV Steel\""}]},"geissele-16-chf-barrel":{"id":"geissele-16-chf-barrel","name":"CHF Chrome Lined Barrel - 5.56 - 16\"","manufacturer":"Geissele Automatics","sku":"05-2984","url":"https://www.primaryarms.com/geissele-automatics-5-56-chf-chrome-lined-ar-15-barrel-mid-length-taper-profile-16in","category":"barrel","description":"Geissele's 16 in cold-hammer-forged 5.56 barrel, stripped, in its taper profile: chrome lined, 1:7 twist, manganese phosphate, a mid-length gas port (.078) on a .750 in journal behind a collar with a dimple opposite the port, an M4 feed ramp extension, a 1/2 x 28 muzzle thread. Sellers' pages: \"This cold hammer-forged 16\\\" barrel features a Geissele Taper Profile and mid-length gas system\" (Primary Arms); its length is stated as 16 (Primary Arms) and as 16.25 (AR15Discounts' list), and the ledger keeps both. Its steel is stated two ways: \"Chrome moly vanadium steel\" (Primary Arms' features; AR15Discounts: \"Material Chrome Moly Vanadium Steel\") and \"Barrel Material 4140 Chrome Moly Steel\" (Primary Arms' table).","weight":"geissele-16-chf-barrel.weight","barrelLength":"geissele-16-chf-barrel.length","cartridge":{"takes":["5.56 NATO"],"stated":"Chambered in 5.56 NATO","source":"https://www.primaryarms.com/geissele-automatics-5-56-chf-chrome-lined-ar-15-barrel-mid-length-taper-profile-16in (the seller's feature list for 05-2984, as cached: harvest.quote; its Specifications: \"Caliber Gauge 5.56 NATO\"; AR15Discounts' page: \"Chamber: 5.56\" and \"Cartridge Compatibility 5.56 NATO\"; Geissele's own site refuses the reader and is left alone)"},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"extension":{"origin":[0,0,0],"note":"The barrel extension's flange, its rear face, on the bore axis, +x toward the muzzle."},"muzzle":{"origin":["{.shoulder_x}",0,0]},"gas_journal":{"origin":["{.gas_port_x}",0,0]}},"interfaces":{"barrel_extension":{"type":"ar15.barrel_extension","role":"barrel","anchor":"extension","params":{},"flips":false,"note":"Primary Arms: \"Feed Ramps M4\"; AR15Discounts: \"Barrel Extension: M4 Feedramps\"."},"muzzle":{"type":"muzzle_thread","role":"barrel","anchor":"muzzle","params":{"thread":"1/2-28","thread_length":"={.thread_length}"},"flips":false,"note":"The sellers' statement: Primary Arms \"Threaded 1/2x28\" and \"Thread Pattern 1/2 X 28\", AR15Discounts \"Muzzle Thread: 1/2 x 28\". No muzzle device comes with it."},"gas_journal":{"type":"ar15.gas_journal","role":"barrel","anchor":"gas_journal","params":{"journal_od":"={.journal_od}"},"flips":false,"note":"Primary Arms: \"Gas Seat Diameter .750\"; AR15Discounts: \"Gas Block Diameter: .750\" and \"Gas Port: .078\"."},"gas_system":{"type":"ar15.gas_system","role":"barrel","params":{"length":"mid"},"flips":false,"note":"Primary Arms: \"Gas System Length Mid-Length\" and \"Mid-Length gas system\"; AR15Discounts: \"Gas Length: Mid-Length\" and \"Gas System Length Midlength\". What the platform checks a gas tube against a barrel by (D83)."}},"materials":{"barrel":{"label":"Barrel","finish":"phosphate","recolorable":false,"color":"geissele-barrel-phosphate","note":"Primary Arms: \"Manganese phosphate exterior finish\" and \"Barrel Coating Manganese Phosphate\"; AR15Discounts: \"Finish: Manganese Phosphate\". The one finish this number is sold in: no colourways. Its colour is the family's (geissele-barrel-phosphate, fitted to the same studio's photos of the 14.5 in and 13.9 in barrels): Primary Arms' side photo of this number reads #383736 over the whole barrel (region [100,600,2100,860], its pixels darker than 200), where the two siblings' side photos read #2f2f2f and #373737 and the preset's fit target was #363636. One slot: in that photo the taper reads #363534, the journal #3b3a39, the thread #332e2b and the extension #2e2a29, a few levels darker and warmer than the barrel ahead of it: the barrel's own matte charcoal, not another finish. Not drawn: the chrome of the bore and the chamber (inside), Geissele's G behind the muzzle ring and the line of marking ahead of the chamber (printed)."}},"components":{},"geometry":{"model":"geissele-16-chf-barrel.glb","components":{},"approximations":["Turned station by station from figures read off Primary Arms' side photo of this barrel (05-2984_02), extension to muzzle. That photo isn't at one scale: at its journal's published .750 its extension reads .974 and its thread's pitch 2.7% short. Its diameters and stations are read through a radial lens distortion about the journal that the journal's .750 and the extension's .999 (the Army's limit) fix, which puts the thread's 28 to the inch where the sellers have it and the flange at 1.166 (the reference CAD set's 1.170); its lengths are then stretched to the published 16 in (16.50 end to end with the extension's half inch), 0.7% from the photo's own 16.61.","Straight between its stations: the chamber section, a cone, the long taper (the \"Geissele Taper Profile\": 0.728 in down to 0.665 over 5.9 in, one straight line within a third of a pixel on the photo), the gas block journal, a cone, the muzzle section, the ring behind the shoulder. The one curve, the flare from the taper up to the collar behind the journal, is a smooth cubic through the traced outline. Every face is square at its station; the photo rounds each corner by its rim's arc, and their real edge breaks aren't drawn.","The gas port, at AR15Discounts' .078 (one seller's figure), is put on top at the station of the dimple on the journal, which is what the side photo shows facing the lens (Primary Arms' three-quarter photo and AR15Discounts' rendering have the port on top just ahead of the collar, opposite it).","The indexing pin at the Army drawing's diameter, standing against the flange's rear face as the Army's Section A-A draws it and AR15Discounts' rendering shows it, as high as the Army's limit (.094): no photo of this barrel has the pin on its silhouette. The bore one plain hole right through, at the Army drawing's .219; the extension's rear opening turned at the reference CAD set's sizes for a mil-spec M4 extension (its chamfered mouth, the ring its locking lugs make, the recess ahead of them).","The muzzle thread is a helix, 28 to the inch, between the minor and major diameters of the Army barrel's 1/2-28 thread (the sellers state 1/2 x 28): a plain V without the flats of its form, right-hand (assumed: its designation marks no other), running out at the shoulder over its last pitch, with no relief there, no chamfer and no crown at the muzzle. Its length is the photo's, 0.656 (the Army barrel's is .63).","Not drawn: the dimple on the journal (0.153 in across by the photo; its depth isn't sourced), the notch in the collar's top in line with the port, the relief at the foot of the collar's front face, the chamber, the slots between the extension's locking lugs and its feed ramps (the lugs are one ring), the G and the marking."],"ledger":["geissele-16-chf-barrel.length","geissele-16-chf-barrel.shoulder_x","geissele-16-chf-barrel.thread_length","geissele-16-chf-barrel.gas_port_x","geissele-16-chf-barrel.journal_od","geissele-16-chf-barrel.muzzle_od","geissele-16-chf-barrel.overall_length","geissele-16-chf-barrel.extension_rear_x","geissele-16-chf-barrel.flange_front_x","geissele-16-chf-barrel.taper_rear_od","geissele-16-chf-barrel.taper_front_od","geissele-16-chf-barrel.journal_rear_x"]},"profiles":{"side":{"plane":"xy","origin":"the silhouette's rear tip, on the axis; the outline begins at the extension's rear face","offset":{"x":"extension_rear_x"},"points":[[0.136,0.473],[0.136,-0.471],[0.143,-0.478],[0.167,-0.486],[0.987,-0.488],[1.061,-0.562],[1.094,-0.562],[1.102,-0.57],[1.217,-0.57],[1.266,-0.521],[1.299,-0.48],[2.004,-0.481],[2.012,-0.473],[2.111,-0.473],[2.119,-0.465],[2.193,-0.465],[2.201,-0.457],[2.275,-0.457],[2.283,-0.449],[2.463,-0.441],[2.472,-0.433],[2.537,-0.433],[2.545,-0.425],[2.627,-0.425],[2.636,-0.417],[2.709,-0.417],[2.718,-0.409],[2.964,-0.393],[2.972,-0.385],[3.144,-0.377],[3.152,-0.368],[3.308,-0.36],[3.316,-0.352],[3.447,-0.361],[3.62,-0.353],[3.628,-0.361],[3.685,-0.361],[3.693,-0.353],[4.768,-0.355],[4.776,-0.347],[5.055,-0.355],[5.063,-0.347],[6.342,-0.349],[6.35,-0.341],[7.555,-0.343],[7.564,-0.335],[8.753,-0.337],[8.777,-0.329],[8.794,-0.337],[8.933,-0.338],[8.941,-0.329],[9.138,-0.33],[9.146,-0.338],[9.212,-0.338],[9.22,-0.346],[9.343,-0.363],[9.564,-0.421],[9.728,-0.421],[9.732,-0.376],[9.745,-0.364],[9.761,-0.372],[10.86,-0.374],[10.868,-0.366],[10.958,-0.366],[10.966,-0.358],[11.335,-0.342],[11.344,-0.334],[12.147,-0.335],[12.155,-0.327],[12.336,-0.335],[12.5,-0.336],[12.508,-0.328],[12.967,-0.337],[13.025,-0.337],[13.033,-0.328],[13.18,-0.329],[13.189,-0.337],[13.221,-0.337],[13.23,-0.329],[14.197,-0.33],[14.205,-0.339],[14.296,-0.339],[14.337,-0.339],[14.345,-0.331],[15.517,-0.333],[15.566,-0.349],[15.804,-0.35],[15.837,-0.342],[15.858,-0.321],[15.866,-0.288],[15.895,-0.26],[15.936,-0.243],[15.952,-0.252],[15.968,-0.243],[15.993,-0.252],[16.001,-0.243],[16.395,-0.244],[16.395,0.248],[16.379,0.24],[16.297,0.24],[16.289,0.248],[16.264,0.24],[16.256,0.248],[16.24,0.24],[16.223,0.248],[16.191,0.24],[16.182,0.248],[16.174,0.24],[16.15,0.248],[16.141,0.24],[16.092,0.24],[16.084,0.248],[16.059,0.24],[16.051,0.248],[16.027,0.24],[16.018,0.248],[15.986,0.24],[15.977,0.249],[15.92,0.24],[15.896,0.249],[15.867,0.277],[15.859,0.31],[15.822,0.347],[15.617,0.348],[15.609,0.339],[15.477,0.331],[15.469,0.323],[15.436,0.323],[15.428,0.332],[15.289,0.332],[14.674,0.333],[14.666,0.325],[14.617,0.325],[14.477,0.325],[14.469,0.333],[14.133,0.334],[14.125,0.326],[14.116,0.334],[13.657,0.335],[13.649,0.326],[13.493,0.327],[13.469,0.335],[13.46,0.327],[13.444,0.335],[13.264,0.335],[13.141,0.336],[13.132,0.327],[13.042,0.328],[13.034,0.336],[12.657,0.328],[12.632,0.336],[12.599,0.328],[12.591,0.337],[12.427,0.337],[12.312,0.337],[12.304,0.329],[12.181,0.329],[12.173,0.337],[12.148,0.329],[12.14,0.337],[12.107,0.329],[11.935,0.329],[11.919,0.338],[11.911,0.33],[11.607,0.33],[11.599,0.338],[11.287,0.339],[11.279,0.347],[11.132,0.347],[11.124,0.355],[10.976,0.356],[10.968,0.364],[10.845,0.364],[10.837,0.372],[9.771,0.374],[9.746,0.366],[9.734,0.378],[9.734,0.411],[9.722,0.424],[9.631,0.424],[9.623,0.416],[9.541,0.416],[9.361,0.367],[9.27,0.359],[9.213,0.342],[9.164,0.343],[9.156,0.334],[6.852,0.338],[6.843,0.347],[6.835,0.338],[6.581,0.339],[6.573,0.347],[6.491,0.347],[6.425,0.339],[6.417,0.347],[4.178,0.351],[4.17,0.36],[4.129,0.36],[4.121,0.351],[3.785,0.352],[3.752,0.36],[3.646,0.36],[3.621,0.352],[3.613,0.361],[3.473,0.361],[3.236,0.353],[3.227,0.361],[3.154,0.361],[3.145,0.37],[3.088,0.37],[3.022,0.386],[2.645,0.411],[2.637,0.42],[2.391,0.436],[2.383,0.445],[2.244,0.445],[2.235,0.453],[2.137,0.462],[2.129,0.47],[1.957,0.478],[1.948,0.486],[1.916,0.478],[1.309,0.479],[1.252,0.545],[1.219,0.562],[1.194,0.57],[1.071,0.57],[1.026,0.533],[0.997,0.488],[0.546,0.489],[0.538,0.481],[0.144,0.481]],"scaleRefs":["geissele-16-chf-barrel.outline_flange_od"],"inputs":{"geissele-16-chf-barrel.outline_flange_od":1.14,"geissele-16-chf-barrel.outline_front_face":16.395,"geissele-16-chf-barrel.outline_rear_face":0.136},"tolerance":0.006,"photo":"references/geissele-16-chf-barrel 3ab505012996 (Primary Arms' gallery, 05-2984_02: the barrel level on white, the muzzle at the left, 2200 x 1467)","method":"luminance < 235, largest piece, holes filled, notches filled in [86, 690, 176, 778] (disk closing, r 6 px); rotated -0.1° as declared; scale from geissele-16-chf-barrel.outline_flange_od = 1.14 in (y-extent 139 px → 122.0 px/in); origin at x min, y center of the outline; clipped to x min {.outline_rear_face} = 0.136, x max {.outline_front_face} = 16.395; Douglas-Peucker at 0.006 in with the extremes kept: 232 points (IoU 0.997 with the full outline); The thread's teeth are filled to their crests: the model draws the thread itself.; checks: centre between the top (max over 0.4 in windows) along x [2.6, 8.0] 0.000 ± 0.025; centre between the top (max over 0.4 in windows) along x [10.9, 15.0] 0.002 ± 0.025; height (tooth tops, max over 0.02 in windows) along x [10.0, 10.8] 0.746 ± 0.025; height (tooth tops, max over 0.02 in windows) along x [0.3, 0.9] 0.975 ± 0.025 (tools/trace.py)","via":"harvest","note":"Black on white, cut out: the outline is the silhouette's at grey 235, at the journal's scale throughout. NOT to scale away from the journal: the photo is yawed, and the extension reads .974 for .999 (outline_extension_od). The model corrects it; its figures are the ledger's. Each face's corner is rounded by its rim's arc."}},"gaps":[{"what":"Every diameter but the journal's, and every station along the barrel","need":"Geissele's own page or drawing (its site refuses the reader): all are read off one seller's photo at 122 px to the inch, through a lens distortion of the photo's own, ± 0.008 in on a diameter and ± 0.03 to 0.04 on a station"},{"what":"The barrel's length: 16 or 16.25 in, and where it is measured from","need":"The maker's statement, or a second page quoting its table: Primary Arms says 16, AR15Discounts' list 16.25, and the photo reads between them"},{"what":"The gas port's own station and its diameter","need":"A straight view of the barrel's top with a scale in its plane, and a second seller's figure: the port is drawn over the dimple, at one page's .078"},{"what":"The dimple's depth; the notch in the collar: its width and depth","need":"Geissele's figures, or a close view of each with its edge on the silhouette"},{"what":"The extension's locking lugs and feed ramps, the chamber's mouth, the muzzle's crown","need":"The extension's drawing (8448550 isn't in the package) and a close view of the muzzle: the extension's inside is the reference CAD set's, turned; hidden once the barrel is in a receiver"},{"what":"Its steel","need":"The maker's own statement: sellers print \"Chrome moly vanadium steel\" and \"4140 Chrome Moly Steel\""}]},"geissele-mk16-105-handguard":{"id":"geissele-mk16-105-handguard","name":"10.5\" Super Modular Rail MK16 M-LOK","manufacturer":"Geissele Automatics","sku":"05-1073B","url":"https://aerospacearms.com/geissele-automatics-10-5-super-modular-rail-mk16-m-lok-black/","category":"handguard","description":"Geissele's 10.5 in free-float M-LOK handguard, with the barrel nut it mounts on. Sellers' pages: \"Mounted to your AR-15 upper using the updated version of the proven Geissele Barrel Nut design\"; \"Anti-rotation tabs and set-screws ensure that your rail will not rotate\"; \"M1913 picatinny rail on top and M-LOK slots on every quadrant\"; \"precision machined using 7000 Series Aluminum\" (Aerospace Arms; Brownells and Charlie's Custom Clones say 6061-T6), \"Type 3 Hardcoat Anodize\"; \"The proprietary 2.25\\\" Geissele barrel nut ensures maximum surface contact with the upper receiver\" (Huckleberry Arms). Its maker's own page isn't read (the site refuses the reader): the page linked is a seller's.","weight":"geissele-mk16-105-handguard.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"mount":{"origin":[0,0,0],"note":"The receiver's front face on the bore axis, +x toward the muzzle."},"mlok":{"origin":["{.mlok_side_slot0_x}",0,0],"note":"On the bore's axis at the side faces' rearmost M-LOK slot's centre (index 0), +x toward the muzzle; the faces are angles about this axis. The lower faces' rows begin at the same place."},"mlok_upper":{"origin":["{.mlok_upper_slot0_x}",0,0],"note":"The same axis at the upper faces' rearmost slot's centre: one slot pitch (40 mm) ahead of the side faces', a sling swivel socket standing where the fifth would be."},"mlok_bottom":{"origin":["{.mlok_bottom_slot0_x}",0,0],"note":"The same axis at the underside's rearmost slot's centre, taken at the side rows' (the underside isn't seen: mlok_bottom_slot0_x)."},"top_rail":{"origin":["{.rail_slot0_x}","{.rail_top_above_bore}",0],"note":"The rail's top at its rearmost slot's centre, +x toward the muzzle (picatinny: index = slot number). Its own rail: the receiver's is the receiver's."}},"interfaces":{"handguard_mount":{"type":"ar15.handguard_mount","role":"handguard","anchor":"mount","params":{"nut":"standard"},"flips":false,"note":"Sellers: \"Mounted to your AR-15 upper using the updated version of the proven Geissele Barrel Nut design\" (Aerospace Arms); \"These handguards are designed to work with Mil-Spec M4 upper receivers. The compatibility with billet receiver sets is unknown.\" (Aerospace Arms); \"Installs using an improved Geissele barrel nut design\" (Primary Arms, of 05-1073B) and \"Geissele barrel nut included\" (Primary Arms, of 05-1073S). It ships with its own barrel nut for the standard thread (each seller gives its weight with and without it). Where its rear face stops isn't published: it is drawn against the receiver's front shoulder (rear_face_x)."},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}","beyond_seam":true,"seam_behind":"receiver","seam_ahead":"handguard"},"flips":false},"mlok":{"type":"mlok","role":"slots","anchor":"mlok","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_side_slots}","interval":"={std.mlok.interval}","face_distance":"={.width} / 2","bore":"={.inside_diameter}","reach_inside":"={.reach_inside}"},"faces":{"right":{"angle":90,"note":"the rifle's right side (+z)"},"left":{"angle":-90}},"flips":false,"note":"The side faces. How far an accessory's nuts may reach inside depends on the barrel and gas block under it, other parts: reach_inside has no figure, so that check reads as unmade."},"mlok_lower":{"type":"mlok","role":"slots","anchor":"mlok","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_lower_slots}","interval":"={std.mlok.interval}","face_distance":"={.lower_face_distance}","bore":"={.inside_diameter}","reach_inside":"={.reach_inside}"},"faces":{"right_lower":{"angle":"{.lower_face_angle}","note":"between the right side and the bottom (about 4:30): its normal 131.4° from the top, read on views of the 13.5 in rail's muzzle end"},"left_lower":{"angle":"0deg - {.lower_face_angle}"}},"flips":false,"note":"The two lower faces: 48.6° from the horizontal in two views of the 13.5 in rail's muzzle end (lower_face_angle), steeper than the upper ones. Their rows stand 0.02 in above the faces' own middle lines; an accessory is placed where a line from the bore meets the face square on."},"mlok_upper":{"type":"mlok","role":"slots","anchor":"mlok_upper","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_upper_slots}","interval":"={std.mlok.interval}","face_distance":"={.upper_face_distance}","bore":"={.inside_diameter}","reach_inside":"={.reach_inside}"},"faces":{"right_upper":{"angle":"{.upper_face_angle}","note":"between the rail and the right side (1:30): 45°, read on a view of the 13.5 in rail's muzzle end"},"left_upper":{"angle":"0deg - {.upper_face_angle}"}},"flips":false,"note":"The two upper faces, at 45° (upper_face_angle). Their rows stand 0.04 in outward of where a line from the bore meets the face square on; an accessory is placed on that line."},"mlok_bottom":{"type":"mlok","role":"slots","anchor":"mlok_bottom","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_bottom_slots}","interval":"={std.mlok.interval}","face_distance":"={.body_bottom_below_bore}","bore":"={.inside_diameter}","reach_inside":"={.reach_inside}"},"faces":{"bottom":{"angle":180,"note":"the underside (6 o'clock)"}},"flips":false,"note":"The bottom flat, 0.86 in below the bore and 0.6 in wide. Sellers: \"M-LOK slots on every quadrant\". Its slots' count and stations are not seen in any photo of this length and are taken as the side rows' (five, from the same place; the 13.5 in rail's foremost four are seen so from inside its muzzle end): where a grip or a hand stop really bolts under it may differ by a slot."}},"materials":{"body":{"label":"Handguard","finish":"anodized","recolorable":true,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized","color":"placeholder-black","sku":"05-1073B","source":"https://aerospacearms.com/geissele-automatics-10-5-super-modular-rail-mk16-m-lok-black/"},"ddc":{"label":"Desert Dirt Color","finish":"anodized","color":"geissele-ddc","sku":"05-1073S","source":"https://www.primaryarms.com/geissele-automatics-super-modular-rail-mk16-m-lok-ddc-10.5in"}},"default":"black","note":"Sellers: \"FINISH: Type 3 Hardcoat Anodize\", \"COLOR: Black\" (Aerospace Arms, of 05-1073B); Primary Arms: \"Mil-Spec Type III hardcoat anodized black finish\", and of 05-1073S \"SKU: 05-1073S\", \"Color Desert Dirt Color\", \"Finish Hardcoat Anodized\", \"Mil-Spec Type III hardcoat DDC finish\", and \"Geissele's Desert Dirt Color (DDC) finish refers to a variety of shades of desert terrain designed to better break up a rifle's outline. These colors can vary drastically even between products from the same batch and are not intended to color match.\" The colour is the 15 in rail's preset (geissele-ddc, matched to Primary Arms' photos of that rail, where its side face reads #8b776d and the preset renders #8a776e). Primary Arms' rail of this length is a lighter, more orange tan: its side face between the slots reads #9c7658 on its left (9919885fa19f), where the same studio's 13.5 in rail reads #665547: three lengths, three shades, as the maker says, and no preset is made for one rail's shade. Black is the placeholder, a plain black anodize in every photo. Mister Guns says on its page for this rail that it is \"also available in 9.3\", 13.5\", and 15\" lengths, as well as in DDC, Gray, and ODG colors\"; no page read gives a number or a picture of a 10.5 in rail in gray or ODG, so neither is offered; and Geissele no longer sells the gray (the user, 2026-11-02: \"geissele's gray is not offerred anymore\")."},"hardware":{"label":"Cross bolts, nut plate and set screws","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The two cross bolts (Torx heads on the right), the nut plate let into the left side and the two set screws in the lower tabs: black steel on the Desert Dirt rail in Primary Arms' three photos of this length in the colour (the plate, the bolts' heads and the set screws are black against the tan), and dark on the black rail in its one photo and Aerospace Arms' two. The finish's name isn't on a page read."},"sockets":{"label":"Sling swivel sockets","finish":"steel","recolorable":false,"color":"geissele-socket-steel","note":"The steel cup let into each upper face: a dark, smooth steel with a bronze or violet cast, on the black rail in Primary Arms' photo of this length (05-1073B_01). Its photos of this length in Desert Dirt Color show the same holes bare, with no cup in them (as Aerospace Arms' photos of the 13.5 in rail do, where Primary Arms' have the cups in both colours): rails photographed before the cups went in, it seems; the cups are drawn, in the dark steel they are on the other lengths' Desert Dirt rails. What they are finished with isn't on a page read."}},"components":{},"geometry":{"model":"geissele-mk16-105-handguard.glb","components":{},"approximations":["Its section is the family's, by reference: no view on file is square on an end of this length. The side faces 0.60 in tall and the bottom flat 0.86 below the bore are the 15 in rail's readings (this length's level photo reads the tube's bottom edge 0.86 below the middle of its side rows); the upper faces at 45°, the lower faces steeper, 48.6° from the horizontal, down to a bottom flat 0.60 in wide, are the 13.5 in rail's, read on views of its muzzle end; the neck under the rail 0.61 wide with a channel 0.47 wide in it is the 15 in rail's. Primary Arms' view of this length from ahead and its right shows the same end as theirs: the rail on its neck, the side faces, lower faces longer than the upper ones, the notch of a trough in the bottom of the muzzle face. It is not a regular octagon.","Its length is 10.505 in by its own rail's 25 slots and two ends at the standard's pitch (the sellers' 10.5 in); the rail's ends are the body's, and the muzzle end is cut square across (on the level photo the side faces' tips and the rail's nose are one plane within 0.01 in once each is read at its own depth, and the view from ahead shows the end as one flat face). The rail's head is MIL-STD-1913's (sellers: \"M1913 picatinny rail\"), its lower faces run in to the neck's walls, its slots the standard's, and its last tooth, a short one on this length, is sloped off over 0.23 in down to 0.09 below the top at the muzzle end, as a plain flat (the bevel down each side of the slope, which the view from ahead shows, isn't drawn).","Inside it is the sellers' 1.26 in: a round bore from the rear face to the first M-LOK slot, 2.47 in on this length (how far the round part really runs isn't seen; a seller gives its barrel nut as 2.25 in long), then flat inner walls that touch that circle and follow the outside. In the bottom, the two side faces and the two upper faces a flat-floored trough runs about the row of slots, 0.49 in wide, its floor leaving 0.09 in of wall: the 13.5 in rail's readings of its muzzle end, by reference, where this length's view from ahead shows only the bottom trough's notch and the side walls' thin ends. The lower faces' walls are whole (0.165 in). The troughs are carried from the first slot to the muzzle end at one width: how far back they run, and the upper faces' width, aren't seen. The channel under the rail runs its whole length, open into the tube.","Five M-LOK slots on each side face and each lower face and four on each upper face, counted on Primary Arms' level photos of each side of this length, at the standard's size and pitch, each row at the height the 15 in rail's level photo shows it. The rows are set from the muzzle end: the foremost slot ends a third of an inch short of it (0.32 as drawn), and the side rows' rearmost begins 2.63 in ahead of the rear face, 0.16 in further forward than on the 13.5 in rail. The underside's row is drawn at the side rows' stations with their count of five, and all five are assumed: no photo on file shows this length's underside, from below or from inside (the row then begins 0.36 in ahead of the clamp block's front as it is drawn, and a quarter of an inch ahead of where the block's ramp ends on the level photo, so the five stand ahead of the block and its split).","The clamp block under the rear end is the traced outline's shape below the tube, as wide as the side faces, its front a flat wall where the outline's ramp comes up to the tube's bottom (2.27 in ahead of the rear face; on the photo the ramp runs out 0.1 in further on), split along its underside by a channel 0.51 in wide that is carried from the rear face to the ramp (its real length isn't seen). The two cross bolts are holes right across with the bolts' heads in counterbores on the right, cut as deep as the holes are wide (their depth isn't seen); the nut plate on the left is drawn with round ends and a straight bar, a groove of 0.024 in round it. The block, the bolts, the plate, the tabs and the sockets are the family's, placed by the 15 in rail's readings: this length's level photo has the plate's two holes, the lower tabs' ends and the socket's hole within 0.01 in of them along the rail, the upper tabs' ends within 0.02, and the lower tabs' top edge within 0.03.","Behind the rear face: a lower tab each side, 0.26 in long, as thick as the side walls (their thickness isn't seen), with a set screw's hole across its middle; and a short upper tab each side under the rail, 0.12 in long, drawn as the section's own outside carried back with the opening between the two taken as a mil-spec receiver's flat sides (0.638 in: the opening isn't seen square on). On the catalog's BCM receiver the right lower tab's top edge stands 0.03 in into the round of the port door's front hinge lug, inside what the two readings carry (the tab's top by a photo, ± 0.02; the lug by the reference model). Each sling swivel socket is its hole through the upper face with a shallow step for the cup; the steel cup is a plain ring in the step, standing half the edge break proud of the face (its four notches and its lip inside aren't drawn; Primary Arms' photo of this length in black has the cup, its three in Desert Dirt Color show the hole bare).","It is drawn with its rear face against the receiver's front shoulder: no page read says where it stops and no photo of it mounted is on file. Its rail's first slot then stands within 0.01 in of where the receiver's own slots would continue.","The steel on it is drawn as pieces of their own, so that it keeps its colour on a rail of another: the nut plate in its seat, the two bolts as plain rounds, their heads in the counterbores and their shanks across the split to end the edge break inside the plate's holes (their Torx sockets and threads aren't drawn), and a set screw in each lower tab as a plain round, flush less the edge break (the photos have them standing out of the tabs, unseated, as shipped).","Not drawn: its barrel nut (inside it, against the receiver), the engraving on its right side (GEISSELE AUTOMATICS / NORTH WALES, PA, on the side face behind its slots), the marks in the rail's slots, and the shallow step along the top of each upper face that runs from the rear face to a point just ahead of the socket (a line in both level photos and in the view from ahead).","Its aluminium by the model is 6.95 cubic inches, 10.9 oz: 1% under the sellers' 11 oz for the handguard alone (3% under the one page that says 11.2). The steel drawn on it (the two bolts, the nut plate, the set screws, the two cups: 0.14 cubic inches) would be 0.65 oz more; whether the sellers' figure has it isn't said."],"ledger":["geissele-mk16-105-handguard.length","geissele-mk16-105-handguard.width","geissele-mk16-105-handguard.height","geissele-mk16-105-handguard.inside_diameter","geissele-mk16-105-handguard.rear_x"]},"profiles":{"side":{"plane":"xy","origin":"the lower tabs' rear ends (behind the rear face) and the rail's top","offset":{"x":"rear_x","y":"rail_top_above_bore"},"points":[[0,-1.557],[0.006,-1.833],[0.074,-1.874],[0.339,-1.874],[0.383,-1.924],[0.471,-1.952],[0.485,-1.987],[0.485,-2.213],[0.502,-2.302],[0.56,-2.371],[0.648,-2.409],[1.017,-2.409],[1.166,-2.326],[1.227,-2.31],[2.197,-2.31],[2.269,-2.277],[2.434,-2.128],[2.517,-2.084],[2.638,-2.056],[10.566,-2.045],[10.59,-2.021],[10.629,-1.811],[10.673,-1.552],[10.679,-1.42],[10.679,-0.918],[10.607,-0.538],[10.607,-0.223],[10.624,-0.108],[10.406,-0.017],[10.273,0],[10.199,-0.014],[10.188,-0.102],[10.169,-0.116],[10.103,-0.116],[10.089,-0.036],[10.069,-0.017],[9.832,-0.006],[9.813,-0.025],[9.802,-0.108],[9.777,-0.121],[9.703,-0.108],[9.697,-0.036],[9.684,-0.022],[9.502,-0.006],[9.433,-0.019],[9.422,-0.113],[9.408,-0.121],[9.32,-0.121],[9.306,-0.036],[9.287,-0.022],[9.066,-0.011],[9.047,-0.036],[9.033,-0.121],[8.934,-0.127],[8.92,-0.119],[8.914,-0.041],[8.824,-0.011],[8.68,-0.017],[8.661,-0.119],[8.647,-0.127],[8.537,-0.127],[8.523,-0.041],[8.46,-0.017],[8.294,-0.022],[8.286,-0.113],[8.272,-0.127],[8.145,-0.127],[8.137,-0.047],[8.107,-0.028],[7.93,-0.017],[7.906,-0.052],[7.906,-0.119],[7.881,-0.132],[7.76,-0.132],[7.746,-0.047],[7.693,-0.022],[7.545,-0.022],[7.531,-0.036],[7.531,-0.119],[7.511,-0.132],[7.368,-0.132],[7.36,-0.052],[7.346,-0.039],[7.307,-0.022],[7.17,-0.022],[7.156,-0.03],[7.15,-0.124],[7.12,-0.138],[6.977,-0.132],[6.968,-0.047],[6.927,-0.022],[6.784,-0.028],[6.775,-0.124],[6.756,-0.138],[6.591,-0.138],[6.582,-0.052],[6.552,-0.028],[6.403,-0.033],[6.406,-0.124],[6.387,-0.138],[6.205,-0.138],[6.197,-0.052],[6.177,-0.028],[6.028,-0.033],[6.012,-0.138],[5.824,-0.138],[5.808,-0.033],[5.67,-0.028],[5.634,-0.058],[5.626,-0.143],[5.433,-0.132],[5.436,-0.036],[5.405,-0.028],[5.284,-0.033],[5.257,-0.05],[5.246,-0.143],[5.069,-0.138],[5.053,-0.033],[4.904,-0.033],[4.868,-0.058],[4.86,-0.143],[4.7,-0.143],[4.686,-0.124],[4.686,-0.047],[4.672,-0.033],[4.501,-0.044],[4.482,-0.058],[4.474,-0.143],[4.319,-0.138],[4.311,-0.047],[4.297,-0.033],[4.154,-0.033],[4.11,-0.05],[4.096,-0.063],[4.088,-0.143],[3.95,-0.143],[3.936,-0.047],[3.922,-0.033],[3.746,-0.044],[3.71,-0.069],[3.702,-0.143],[3.575,-0.143],[3.553,-0.039],[3.41,-0.033],[3.33,-0.063],[3.311,-0.149],[3.2,-0.143],[3.187,-0.047],[3.167,-0.033],[3.04,-0.033],[2.963,-0.05],[2.944,-0.063],[2.938,-0.141],[2.925,-0.149],[2.825,-0.143],[2.812,-0.047],[2.787,-0.033],[2.583,-0.05],[2.558,-0.069],[2.544,-0.149],[2.451,-0.143],[2.437,-0.052],[2.412,-0.033],[2.186,-0.055],[2.164,-0.149],[2.081,-0.149],[2.048,-0.039],[1.817,-0.05],[1.792,-0.063],[1.772,-0.149],[1.712,-0.149],[1.698,-0.135],[1.673,-0.039],[1.431,-0.05],[1.406,-0.069],[1.392,-0.149],[1.323,-0.141],[1.298,-0.039],[1.034,-0.055],[1.006,-0.149],[0.948,-0.141],[0.923,-0.039],[0.334,-0.05],[0.309,-0.108],[0.309,-0.179],[0.331,-0.256],[0.331,-0.466],[0.311,-0.496],[0.185,-0.502],[0.171,-0.515],[0.138,-0.675],[0.168,-0.7],[0.287,-0.703],[0.243,-0.951],[0.248,-1.497],[0.069,-1.5]],"scaleRefs":["geissele-mk16-105-handguard.overall_length","geissele-mk16-105-handguard.height"],"inputs":{"geissele-mk16-105-handguard.height":2.39,"geissele-mk16-105-handguard.overall_length":10.765},"tolerance":0.01,"photo":"references/geissele-mk16-105-handguard 9919885fa19f (Primary Arms' gallery for 05-1073S, 05-1073S_02.jpg: the handguard alone in Desert Dirt Color, its left side seen level, muzzle to the left, 2200 x 1467)","method":"luminance < 215, largest piece, holes filled; scale from geissele-mk16-105-handguard.overall_length = 10.765 in (x-extent 1937 px → 179.9 px/in) and geissele-mk16-105-handguard.height = 2.39 in (y-extent 437 px → 182.8 px/in), which agree within 1.6%; mean 181.4 px/in; origin at x min, y max of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 196 points (IoU 0.997 with the full outline) (tools/trace.py)","via":"harvest","note":"The slots are inside the outline (filled); the model cuts them. Its left side, mirrored: the plate with two holes is this side's, the bolt heads the other's. A tan rail on white, cut at a luminance of 215. The model takes only the clamp block's shape from it."}},"gaps":[{"what":"The M-LOK slots on its underside: how many, and where they begin (sellers: \"M-LOK slots on every quadrant\"; drawn and offered as the side rows' five at the side rows' stations, assumed)","need":"A photo of it from below, or into its muzzle end: no view on file shows the bottom face"},{"what":"Where it stops on the receiver (rear_face_x: drawn against the front shoulder with no gap)","need":"A photo of it mounted on a mil-spec upper, or the maker's instruction sheet from a page that may be read"},{"what":"Its section square on at this length (the faces' lean, the bottom flat and the troughs inside are the 13.5 in rail's readings; the rear end's round bore and the neck are the 15 in rail's readings of a shorter rail)","need":"A view square on an end of the 10.5 in rail with a known size in frame"},{"what":"Its weight: sellers give 11 oz (12.6 with the nut) and 11.2 oz (12.84)","need":"The maker's own figure, from a page that may be read"},{"what":"The room inside its faces before the barrel (reach_inside: what an M-LOK accessory's nuts may take)","need":"The barrel's and the gas block's size under it, from the parts a build puts there"},{"what":"Its Desert Dirt Color as the maker means it (the preset is one seller's 15 in rail; the same seller's rail of this length is a lighter, more orange tan, and the maker says the colour varies from rail to rail)","need":"The maker's own pictures of the DDC rail, from a page that may be read"}]},"geissele-mk16-135-handguard":{"id":"geissele-mk16-135-handguard","name":"13.5\" Super Modular Rail MK16 M-LOK","manufacturer":"Geissele Automatics","sku":"05-650B","url":"https://aerospacearms.com/geissele-automatics-13-5-super-modular-rail-mk16-m-lok-black/","category":"handguard","description":"Geissele's 13.5 in free-float M-LOK handguard, with the barrel nut it mounts on. Sellers' pages: \"Mounted to your AR-15 upper using the updated version of the proven Geissele Barrel Nut design\"; \"Anti-rotation tabs and set-screws ensure that your rail will not rotate\"; \"M1913 picatinny rail on top and M-LOK slots on every quadrant\"; \"precision machined using 7000 Series Aluminum\" (Aerospace Arms; Brownells and Sportsman's Warehouse say 6061-T6), \"Type 3 Hardcoat Anodize\"; \"this 13.5\\\" version pairs an extended barrel nut with seven sides of M-LOK\" (Primary Arms). Its maker's own page isn't read (the site refuses the reader): the page linked is a seller's.","weight":"geissele-mk16-135-handguard.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"mount":{"origin":[0,0,0],"note":"The receiver's front face on the bore axis, +x toward the muzzle."},"mlok":{"origin":["{.mlok_side_slot0_x}",0,0],"note":"On the bore's axis at the side faces' rearmost M-LOK slot's centre (index 0), +x toward the muzzle; the faces are angles about this axis. The lower faces' rows begin at the same place."},"mlok_upper":{"origin":["{.mlok_upper_slot0_x}",0,0],"note":"The same axis at the upper faces' rearmost slot's centre: one slot pitch (40 mm) ahead of the side faces', a sling swivel socket standing where the seventh would be."},"mlok_bottom":{"origin":["{.mlok_bottom_slot0_x}",0,0],"note":"The same axis at the underside's rearmost slot's centre, taken at the side rows' (the foremost four of the underside's slots are seen there from inside the muzzle end; the rear three aren't seen: mlok_bottom_slot0_x)."},"top_rail":{"origin":["{.rail_slot0_x}","{.rail_top_above_bore}",0],"note":"The rail's top at its rearmost slot's centre, +x toward the muzzle (picatinny: index = slot number). Its own rail: the receiver's is the receiver's."}},"interfaces":{"handguard_mount":{"type":"ar15.handguard_mount","role":"handguard","anchor":"mount","params":{"nut":"standard"},"flips":false,"note":"Sellers: \"Mounted to your AR-15 upper using the updated version of the proven Geissele Barrel Nut design\" (Aerospace Arms); \"These handguards are designed to work with Mil-Spec M4 upper receivers. The compatibility with billet receiver sets is unknown.\" (Aerospace Arms); \"Extended-length Geissele barrel nut\", \"Does not include barrel nut wrench\" (Primary Arms). It ships with its own barrel nut for the standard thread (each seller gives its weight with and without it). Where its rear face stops isn't published: it is drawn against the receiver's front shoulder (rear_face_x)."},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}","beyond_seam":true,"seam_behind":"receiver","seam_ahead":"handguard"},"flips":false},"mlok":{"type":"mlok","role":"slots","anchor":"mlok","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_side_slots}","interval":"={std.mlok.interval}","face_distance":"={.width} / 2","bore":"={.inside_diameter}","reach_inside":"={.reach_inside}"},"faces":{"right":{"angle":90,"note":"the rifle's right side (+z)"},"left":{"angle":-90}},"flips":false,"note":"The side faces. How far an accessory's nuts may reach inside depends on the barrel and gas block under it, other parts: reach_inside has no figure, so that check reads as unmade."},"mlok_lower":{"type":"mlok","role":"slots","anchor":"mlok","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_lower_slots}","interval":"={std.mlok.interval}","face_distance":"={.lower_face_distance}","bore":"={.inside_diameter}","reach_inside":"={.reach_inside}"},"faces":{"right_lower":{"angle":"{.lower_face_angle}","note":"between the right side and the bottom (about 4:30): its normal 131.4° from the top, read on a view of the muzzle end"},"left_lower":{"angle":"0deg - {.lower_face_angle}"}},"flips":false,"note":"The two lower faces: 48.6° from the horizontal in two views of this length's muzzle end (lower_face_angle), steeper than the upper ones. Their rows stand 0.02 in above the faces' own middle lines; an accessory is placed where a line from the bore meets the face square on."},"mlok_upper":{"type":"mlok","role":"slots","anchor":"mlok_upper","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_upper_slots}","interval":"={std.mlok.interval}","face_distance":"={.upper_face_distance}","bore":"={.inside_diameter}","reach_inside":"={.reach_inside}"},"faces":{"right_upper":{"angle":"{.upper_face_angle}","note":"between the rail and the right side (1:30): 45°, read on a view of the muzzle end"},"left_upper":{"angle":"0deg - {.upper_face_angle}"}},"flips":false,"note":"The two upper faces, at 45° (upper_face_angle). Their rows stand 0.04 in outward of where a line from the bore meets the face square on; an accessory is placed on that line."},"mlok_bottom":{"type":"mlok","role":"slots","anchor":"mlok_bottom","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_bottom_slots}","interval":"={std.mlok.interval}","face_distance":"={.body_bottom_below_bore}","bore":"={.inside_diameter}","reach_inside":"={.reach_inside}"},"faces":{"bottom":{"angle":180,"note":"the underside (6 o'clock)"}},"flips":false,"note":"The bottom flat, 0.86 in below the bore and 0.6 in wide. Sellers: \"M-LOK slots on every quadrant\"; \"seven sides of M-LOK\". Its foremost four slots are seen from inside the muzzle end, at the side rows' stations; how far back the row runs isn't seen, and it is taken as the side rows' seven from the same place: where a grip or a hand stop bolts under its rear half may differ by a slot."}},"materials":{"body":{"label":"Handguard","finish":"anodized","recolorable":true,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized","color":"placeholder-black","sku":"05-650B","source":"https://aerospacearms.com/geissele-automatics-13-5-super-modular-rail-mk16-m-lok-black/"},"ddc":{"label":"Desert Dirt Color","finish":"anodized","color":"geissele-ddc","sku":"05-650S","source":"https://www.primaryarms.com/geissele-automatics-13.5-in-super-modular-rail-m-lok-ddc"}},"default":"black","note":"Sellers: \"FINISH: Type 3 Hardcoat Anodize\" (Aerospace Arms, of 05-650B \"COLOR: Black\" and of 05-650S \"COLOR: Desert Dirt Color (DDC)\"); Primary Arms: \"Black Type III hardcoat anodize\", and of 05-650S \"SKU: 05-650S\", \"Color Brown\", \"Finish Hardcoat Anodized\", \"DDC Type III hardcoat anodize\", and \"Geissele's Desert Dirt Color (DDC) finish refers to a variety of shades of desert terrain designed to better break up a rifle's outline. These colors can vary drastically even between products from the same batch and are not intended to color match.\" The colour is the 15 in rail's preset (geissele-ddc, matched to Primary Arms' photos of that rail, where its side face reads #8b776d and the preset renders #8a776e): three rails, three shades, as the maker says. Primary Arms' rail of this length is a darker brown (its side face between the slots reads #665547 on its left, a7f8c9566fda, and #685648 on its right, d8f68919b0da), and Aerospace Arms' rail of this length, marked PN: 05-650S, a yellower tan (#8e7c5d to #998666, e48a010fa0ad); the preset stands between the two, and no second preset is made for one rail's shade. Black is the placeholder, a plain black anodize in every photo. Mister Guns says of the family \"also available in black, gray, and ODG colors\"; no page read gives a number or a picture of a 13.5 in rail in gray or ODG, so neither is offered; and Geissele no longer sells the gray (the user, 2026-11-02: \"geissele's gray is not offerred anymore\")."},"hardware":{"label":"Cross bolts, nut plate and set screws","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The two cross bolts (Torx heads on the right), the nut plate let into the left side and the two set screws in the lower tabs: black steel on the black rail and on the Desert Dirt one, in Primary Arms' and Aerospace Arms' photos of this length in each colour (the plate, the bolts' heads and the set screws are black against the tan). The finish's name isn't on a page read."},"sockets":{"label":"Sling swivel sockets","finish":"steel","recolorable":false,"color":"geissele-socket-steel","note":"The steel cup let into each upper face: a dark, smooth steel with a bronze or violet cast, the same on the black rail and the Desert Dirt one in Primary Arms' photos of this length (05-650B_03, 05-650S_02, 05-650S_03). Aerospace Arms' photos of this length show the same holes bare, with no cup in them: older pictures, or rails photographed before the cups went in; the cups are drawn. What they are finished with isn't on a page read."}},"components":{},"geometry":{"model":"geissele-mk16-135-handguard.glb","components":{},"approximations":["Its section is the family's with what this length's muzzle end shows (Aerospace Arms' views from ahead, scaled by the sellers' 1.59 in across the side faces): the side faces 0.60 in tall and the bottom flat 0.86 below the bore (the 15 in rail's level photo; 0.61 and 0.86 on this length's end), the upper faces at 45° (44 to 45° there), the lower faces steeper, 48.6° from the horizontal (two photos within 0.1°), down to a bottom flat 0.60 in wide (0.61 there); the neck under the rail 0.61 wide with a channel 0.47 wide in it (0.61 and 0.45 there). It is not a regular octagon, and its lower faces are not at the 45° the 15 in rail is drawn with.","Its length is 13.52 in by its own rail's 32 slots and two ends at the standard's pitch (the sellers' 13.5 in); the rail's ends are the body's, and the muzzle end is cut square across (on the level photo the side faces' tips and the rail's nose are one plane within 0.02 in once each is read at its own depth). The rail's head is MIL-STD-1913's (sellers: \"M1913 picatinny rail\"), its lower faces run in to the neck's walls, its slots the standard's, and its last tooth is sloped off over 0.29 in down to 0.11 below the top at the muzzle end, as a plain flat (its side bevels aren't drawn).","Inside it is the sellers' 1.26 in: a round bore from the rear face to the first M-LOK slot (how far the round part really runs isn't seen), then flat inner walls that touch that circle and follow the outside. In the bottom, the two side faces and the two upper faces a flat-floored trough runs about the row of slots, 0.49 in wide, its floor leaving 0.09 in of wall: the bottom's is seen at the muzzle end with its steps, the side walls' ends are as thin there and the upper walls' look so; the lower faces' walls are whole (0.165 in), with a step where a side wall meets one, as a view from ahead and beside shows. The troughs are carried from the first slot to the muzzle end at one width: how far back they run, and the upper faces' width, aren't seen. The channel under the rail runs its whole length, open into the tube.","Seven M-LOK slots on each side face and each lower face and six on each upper face, counted on photos of this length, at the standard's size and pitch, each row at the height the 15 in rail's level photo shows it. The underside's row is drawn at the side rows' stations with their count of seven: its foremost four are seen there from inside the muzzle end, the rear three are assumed (the side rows' rearmost slot begins 0.1 in ahead of the clamp block's front, so the seven stand ahead of the block and its split).","The clamp block under the rear end is the traced outline's shape below the tube, as wide as the side faces, its front a flat wall where the outline's ramp ends, split along its underside by a channel 0.51 in wide that is carried from the rear face to the ramp (its real length isn't seen). The two cross bolts are holes right across with the bolts' heads in counterbores on the right, cut as deep as the holes are wide (their depth isn't seen); the nut plate on the left is drawn with round ends and a straight bar, a groove of 0.024 in round it. The block, the bolts, the plate, the tabs and the sockets are the family's, placed by the 15 in rail's readings: this length's level photo has each within 0.02 in of them.","Behind the rear face: a lower tab each side, 0.26 in long, as thick as the side walls (their thickness isn't seen), with a set screw's hole across its middle; and a short upper tab each side under the rail, 0.12 in long, drawn as the section's own outside carried back with the opening between the two taken as a mil-spec receiver's flat sides (0.638 in: the opening isn't seen square on). On the catalog's BCM receiver the right lower tab's top edge stands 0.03 in into the round of the port door's front hinge lug, inside what the two readings carry (the tab's top by a photo, ± 0.02; the lug by the reference model). Each sling swivel socket is its hole through the upper face with a shallow step for the cup; the steel cup is a plain ring in the step, standing half the edge break proud of the face (its four notches and its lip inside aren't drawn).","It is drawn with its rear face against the receiver's front shoulder: no page read says where it stops and no photo of it mounted is on file. Its rail's first slot then stands 0.01 in from where the receiver's own slots would continue.","The steel on it is drawn as pieces of their own, so that it keeps its colour on a rail of another: the nut plate in its seat, the two bolts as plain rounds, their heads in the counterbores and their shanks across the split to end the edge break inside the plate's holes (their Torx sockets and threads aren't drawn), and a set screw in each lower tab as a plain round, flush less the edge break (the photos have them standing out of the tabs, unseated, as shipped).","Not drawn: its barrel nut (inside it, against the receiver), the engraving on its sides (GEISSELE AUTOMATICS / NORTH WALES, PA on the right; the maker's name or an NSN on the left) and the marks in the rail's slots.","Its aluminium by the model is 8.33 cubic inches, 13.1 oz: 3% under the sellers' 13.4 oz for the handguard alone (with whole walls everywhere but the bottom it would be 14.3 oz, and with a trough in the lower faces too 12.4). The steel drawn on it (the two bolts, the nut plate, the set screws, the two cups: 0.14 cubic inches) would be 0.6 oz more; whether the sellers' figure has it isn't said."],"ledger":["geissele-mk16-135-handguard.length","geissele-mk16-135-handguard.width","geissele-mk16-135-handguard.height","geissele-mk16-135-handguard.inside_diameter","geissele-mk16-135-handguard.rear_x"]},"profiles":{"side":{"plane":"xy","origin":"the lower tabs' rear ends (behind the rear face) and the rail's top","offset":{"x":"rear_x","y":"rail_top_above_bore"},"points":[[0,-1.555],[0.007,-1.846],[0.058,-1.883],[0.335,-1.883],[0.383,-1.924],[0.45,-1.944],[0.474,-1.981],[0.474,-2.232],[0.495,-2.313],[0.566,-2.391],[0.647,-2.418],[0.999,-2.418],[1.243,-2.317],[2.219,-2.31],[2.293,-2.269],[2.496,-2.093],[2.652,-2.046],[10.517,-2.032],[13.443,-2.046],[13.474,-2.029],[13.494,-1.981],[13.603,-1.568],[13.616,-1.06],[13.616,-0.965],[13.501,-0.539],[13.508,-0.234],[13.535,-0.173],[13.535,-0.132],[13.504,-0.108],[13.315,-0.041],[13.179,-0.014],[12.841,-0.014],[12.817,-0.119],[12.793,-0.122],[12.759,-0.034],[12.509,-0.007],[12.458,-0.024],[12.438,-0.119],[12.407,-0.122],[12.39,-0.051],[12.366,-0.034],[12.224,-0.007],[12.102,-0.007],[12.078,-0.037],[12.065,-0.119],[12.028,-0.122],[12.004,-0.044],[11.987,-0.034],[11.899,-0.014],[11.723,-0.007],[11.699,-0.051],[11.692,-0.119],[11.642,-0.122],[11.625,-0.051],[11.601,-0.034],[11.526,-0.014],[11.343,-0.007],[11.32,-0.064],[11.32,-0.112],[11.255,-0.122],[11.238,-0.044],[11.222,-0.034],[11.147,-0.014],[10.971,-0.007],[10.954,-0.024],[10.94,-0.119],[10.869,-0.122],[10.842,-0.034],[10.754,-0.007],[10.592,-0.007],[10.568,-0.112],[10.51,-0.122],[10.48,-0.112],[10.473,-0.051],[10.422,-0.02],[10.219,-0.007],[10.202,-0.03],[10.195,-0.112],[10.124,-0.122],[10.094,-0.112],[10.087,-0.044],[10.063,-0.027],[9.989,-0.007],[9.846,-0.007],[9.829,-0.017],[9.823,-0.105],[9.799,-0.122],[9.752,-0.122],[9.707,-0.112],[9.701,-0.044],[9.663,-0.02],[9.616,-0.007],[9.467,-0.007],[9.443,-0.112],[9.372,-0.122],[9.332,-0.115],[9.315,-0.037],[9.25,-0.007],[9.088,-0.007],[9.067,-0.115],[8.945,-0.115],[8.925,-0.034],[8.857,-0.007],[8.783,0],[8.705,-0.01],[8.688,-0.115],[8.559,-0.115],[8.549,-0.044],[8.471,0],[8.336,-0.007],[8.315,-0.115],[8.173,-0.115],[8.163,-0.037],[8.132,-0.014],[8.092,0],[7.963,0],[7.946,-0.112],[7.895,-0.122],[7.787,-0.115],[7.777,-0.037],[7.753,-0.014],[7.699,0],[7.584,-0.007],[7.563,-0.115],[7.401,-0.115],[7.397,-0.044],[7.374,-0.014],[7.326,0],[7.204,-0.007],[7.191,-0.115],[7.022,-0.115],[6.998,-0.017],[6.961,0],[6.832,-0.007],[6.825,-0.115],[6.635,-0.115],[6.618,-0.01],[6.588,0],[6.452,-0.007],[6.439,-0.115],[6.256,-0.115],[6.239,-0.098],[6.239,-0.01],[6.215,0],[6.08,-0.007],[6.053,-0.115],[5.877,-0.115],[5.86,-0.085],[5.856,-0.007],[5.707,0],[5.677,-0.037],[5.67,-0.112],[5.619,-0.122],[5.497,-0.115],[5.487,-0.017],[5.443,0],[5.321,-0.007],[5.291,-0.037],[5.281,-0.115],[5.125,-0.115],[5.108,-0.01],[5.084,0],[4.996,0],[4.915,-0.027],[4.894,-0.115],[4.745,-0.115],[4.735,-0.017],[4.718,0],[4.61,0],[4.542,-0.02],[4.518,-0.037],[4.508,-0.115],[4.373,-0.115],[4.352,-0.007],[4.224,0],[4.132,-0.037],[4.122,-0.115],[4.068,-0.122],[3.993,-0.115],[3.976,-0.01],[3.932,0],[3.824,0],[3.75,-0.034],[3.729,-0.115],[3.614,-0.115],[3.604,-0.017],[3.567,0],[3.424,-0.007],[3.36,-0.037],[3.343,-0.115],[3.235,-0.115],[3.214,-0.007],[3.099,0],[2.977,-0.034],[2.96,-0.112],[2.93,-0.122],[2.862,-0.115],[2.845,-0.017],[2.788,0],[2.679,-0.007],[2.598,-0.034],[2.581,-0.051],[2.571,-0.115],[2.483,-0.115],[2.456,-0.007],[2.286,-0.007],[2.219,-0.027],[2.195,-0.051],[2.185,-0.115],[2.1,-0.112],[2.076,-0.007],[1.907,-0.007],[1.832,-0.027],[1.809,-0.044],[1.792,-0.115],[1.721,-0.112],[1.714,-0.037],[1.69,0],[1.555,-0.007],[1.433,-0.034],[1.409,-0.112],[1.385,-0.122],[1.341,-0.112],[1.318,-0.007],[1.148,-0.007],[1.06,-0.027],[1.03,-0.051],[1.013,-0.122],[0.962,-0.112],[0.948,-0.024],[0.931,-0.007],[0.417,-0.014],[0.335,-0.034],[0.312,-0.085],[0.312,-0.173],[0.332,-0.24],[0.332,-0.45],[0.315,-0.481],[0.183,-0.498],[0.142,-0.647],[0.149,-0.681],[0.173,-0.698],[0.285,-0.708],[0.237,-0.959],[0.244,-1.494],[0.051,-1.504]],"scaleRefs":["geissele-mk16-135-handguard.overall_length","geissele-mk16-135-handguard.height"],"inputs":{"geissele-mk16-135-handguard.height":2.39,"geissele-mk16-135-handguard.overall_length":13.78},"tolerance":0.01,"photo":"references/geissele-mk16-135-handguard e4af6c8f0204 (Primary Arms' gallery for 05-650B, 05-650B_03.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","method":"luminance < 200, largest piece, holes filled; scale from geissele-mk16-135-handguard.overall_length = 13.78 in (x-extent 2010 px → 145.9 px/in) and geissele-mk16-135-handguard.height = 2.39 in (y-extent 357 px → 149.4 px/in), which agree within 2.4%; mean 147.6 px/in; origin at x min, y max of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 246 points (IoU 0.997 with the full outline) (tools/trace.py)","via":"harvest","note":"The slots are inside the outline (filled); the model cuts them. Its left side, mirrored: the plate with two holes is this side's, the bolt heads the other's. The outline's scale is the mean of two that stand 2.2% apart (its ends are the near face's, and the photo is from a little above); the model takes only the clamp block's shape from it."}},"gaps":[{"what":"The M-LOK slots on the rear half of its underside: how many the row has (its foremost four are seen from inside the muzzle end; drawn and offered as the side rows' seven at the side rows' stations)","need":"A photo of it from below: no view on file shows the bottom face"},{"what":"Where it stops on the receiver (rear_face_x: drawn against the front shoulder with no gap)","need":"A photo of it mounted on a mil-spec upper, or the maker's instruction sheet from a page that may be read"},{"what":"Its section behind the muzzle end (the trough inside the bottom is seen at the muzzle end only; the rear end's round bore and the neck are the 15 in rail's readings of a shorter rail)","need":"A view into its rear end with a known size in frame"},{"what":"The room inside its faces before the barrel (reach_inside: what an M-LOK accessory's nuts may take)","need":"The barrel's and the gas block's size under it, from the parts a build puts there"},{"what":"Its Desert Dirt Color as the maker means it (the preset is one seller's rail; another seller's rail of this length is a yellower tan, and the maker says the colour varies from rail to rail)","need":"The maker's own pictures of the DDC rail, from a page that may be read"}]},"geissele-mk16-15-handguard":{"id":"geissele-mk16-15-handguard","name":"15\" Super Modular Rail MK16 M-LOK","manufacturer":"Geissele Automatics","sku":"05-792B","url":"https://www.milehighshooting.com/geissele-15-super-modular-rail-mk16-m-lok/","category":"handguard","description":"Geissele's 15 in free-float M-LOK handguard, with the barrel nut it mounts on. Sellers' pages: \"Mounted to your AR-15 upper using the updated version of the proven Geissele Barrel Nut design\"; \"Anti-rotation tabs and set-screws ensure that your rail will not rotate\"; \"M1913 picatinny rail on top and M-LOK slots on every quadrant\"; \"precision machined using 7000 Series Aluminum\" (Mile High Shooting; two other sellers say 6061-T6), \"Type 3 Hardcoat Anodize\". Its maker's own page isn't read (the site refuses the reader): the page linked is a seller's.","weight":"geissele-mk16-15-handguard.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"mount":{"origin":[0,0,0],"note":"The receiver's front face on the bore axis, +x toward the muzzle."},"mlok":{"origin":["{.mlok_side_slot0_x}",0,0],"note":"On the bore's axis at the side faces' rearmost M-LOK slot's centre (index 0), +x toward the muzzle; the faces are angles about this axis. The lower faces' rows begin at the same place."},"mlok_upper":{"origin":["{.mlok_upper_slot0_x}",0,0],"note":"The same axis at the upper faces' rearmost slot's centre: one slot pitch (40 mm) ahead of the side faces', a sling swivel socket standing where the eighth would be."},"mlok_bottom":{"origin":["{.mlok_bottom_slot0_x}",0,0],"note":"The same axis at the underside's rearmost slot's centre, taken at the side rows' (the underside isn't seen: mlok_bottom_slot0_x)."},"top_rail":{"origin":["{.rail_slot0_x}","{.rail_top_above_bore}",0],"note":"The rail's top at its rearmost slot's centre, +x toward the muzzle (picatinny: index = slot number). Its own rail: the receiver's is the receiver's."}},"interfaces":{"handguard_mount":{"type":"ar15.handguard_mount","role":"handguard","anchor":"mount","params":{"nut":"standard"},"flips":false,"note":"Sellers: \"Mounted to your AR-15 upper using the updated version of the proven Geissele Barrel Nut design\" (Mile High Shooting, Rifle Supply); Hero Outdoors: \"Compatibility: Mil-Spec M4/AR15 upper receivers\". It ships with its own barrel nut for the standard thread (each seller gives its weight with and without it). Where its rear face stops isn't published: it is drawn against the receiver's front shoulder (rear_face_x)."},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}","beyond_seam":true,"seam_behind":"receiver","seam_ahead":"handguard"},"flips":false},"mlok":{"type":"mlok","role":"slots","anchor":"mlok","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_side_slots}","interval":"={std.mlok.interval}","face_distance":"={.width} / 2","bore":"={.inside_diameter}","reach_inside":"={.reach_inside}"},"faces":{"right":{"angle":90,"note":"the rifle's right side (+z)"},"left":{"angle":-90}},"flips":false,"note":"The side faces. How far an accessory's nuts may reach inside depends on the barrel and gas block under it, other parts: reach_inside has no figure, so that check reads as unmade."},"mlok_lower":{"type":"mlok","role":"slots","anchor":"mlok","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_lower_slots}","interval":"={std.mlok.interval}","face_distance":"={.diag_face_distance}","bore":"={.inside_diameter}","reach_inside":"={.reach_inside}"},"faces":{"right_lower":{"angle":135,"note":"between the right side and the bottom (4:30)"},"left_lower":{"angle":-135}},"flips":false,"note":"The two lower faces, taken at 45° (the angle isn't published: diag_face_distance). Their rows stand 0.02 in below the faces' own middle lines as the level photo reads them; an accessory is placed on the middle line."},"mlok_upper":{"type":"mlok","role":"slots","anchor":"mlok_upper","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_upper_slots}","interval":"={std.mlok.interval}","face_distance":"={.diag_face_distance}","bore":"={.inside_diameter}","reach_inside":"={.reach_inside}"},"faces":{"right_upper":{"angle":45,"note":"between the rail and the right side (1:30)"},"left_upper":{"angle":-45}},"flips":false,"note":"The two upper faces, taken at 45°. Their rows stand 0.04 in outward of where a line from the bore meets the face square on; an accessory is placed on that line."},"mlok_bottom":{"type":"mlok","role":"slots","anchor":"mlok_bottom","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_bottom_slots}","interval":"={std.mlok.interval}","face_distance":"={.body_bottom_below_bore}","bore":"={.inside_diameter}","reach_inside":"={.reach_inside}"},"faces":{"bottom":{"angle":180,"note":"the underside (6 o'clock)"}},"flips":false,"note":"The bottom flat, 0.86 in below the bore. Sellers: \"M-LOK slots on every quadrant\". Its slots' count and stations are not seen in any photo on file and are taken as the side rows' (eight, from the same place): where a grip or a hand stop really bolts under it may differ by a slot."}},"materials":{"body":{"label":"Handguard","finish":"anodized","recolorable":true,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized","color":"placeholder-black","sku":"05-792B","source":"https://www.milehighshooting.com/geissele-15-super-modular-rail-mk16-m-lok/"},"ddc":{"label":"Desert Dirt Color","finish":"anodized","color":"geissele-ddc","sku":"05-792S","source":"https://www.primaryarms.com/geissele-automatics-super-modular-rail-mk16-mlok-ddc-15in"}},"default":"black","note":"Sellers: \"Type 3 Hardcoat Anodize\"; Primary Arms of 05-792S: \"SKU: 05-792S\", \"Color Desert Dirt Color\", \"Finish Hardcoat Anodized\", \"Mil-Spec Type III hardcoat DDC finish\", and \"Geissele's Desert Dirt Color (DDC) finish refers to a variety of shades of desert terrain designed to better break up a rifle's outline. These colors can vary drastically even between products from the same batch and are not intended to color match.\" The colour here is the one rail in Primary Arms' three photos of 05-792S, matched under the app's light: a seller's own picture, not the maker's standard, and another rail may be lighter, pinker or more olive (AR15Discounts' small picture of the 15 in rail is a pale peach, Bullet Central's of a short one an olive brown). Black is the placeholder: Primary Arms' photos of 05-792B read as a plain black anodize (its side face #363439 where the app's black receivers read #42 to #44). Charlie's Custom Clones lists \"COLOR: Black, DDC, Gray, ODG\" for the MK16 family; no page read gives a number or a picture of a 15 in rail in gray or ODG, so neither is offered; and Geissele no longer sells the gray (the user, 2026-11-02: \"geissele's gray is not offerred anymore\")."},"hardware":{"label":"Cross bolts, nut plate and set screws","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The two cross bolts (Torx heads on the right), the nut plate let into the left side and the two set screws in the lower tabs: black steel on the black rail and on the Desert Dirt one (Primary Arms' photos of 05-792B and of 05-792S: the plate, the bolts' heads and the set screws are black against the tan). The finish's name isn't on a page read. The bolt heads look bright in the maker's own studio picture of the black rail (Mile High's), where the whole rail is lit to a pale grey; Primary Arms' photos of the same rail have them black."},"sockets":{"label":"Sling swivel sockets","finish":"steel","recolorable":false,"color":"geissele-socket-steel","note":"The steel cup let into each upper face: a dark, smooth steel with a bronze or violet cast in every photo, the same on the black rail and the Desert Dirt one (Primary Arms' photos of both; coppery in the maker's studio picture at Mile High). What it is finished with isn't on a page read. Its colour is read off the photos and not fitted: a smooth dark metal's brightness in a photo is what it reflects (#312628 in one, #665a5a and #a1a0ae in two others)."}},"components":{},"geometry":{"model":"geissele-mk16-15-handguard.glb","components":{},"approximations":["Its section is drawn from the sellers' 1.59 in across the side faces and three photos, none square on this length's end: the side faces 0.60 in tall and the bottom flat 0.86 below the bore (Primary Arms' level photo), the faces between taken at 45° through the side faces' creases (the angle isn't published; a rear view of a shorter MK16 draws them at 44°), the neck under the rail 0.61 wide with a channel 0.47 wide in it (that rear view, of a 9.3 or 10.5 in rail of the same model). It is not a regular octagon: the lower faces are longer than the upper ones and the bottom flat narrower than the sides.","Its length is 15.12 in by its own rail's 36 slots and two ends at the standard's pitch (the sellers' 15 in is the size's name); the rail's ends are the body's, and the muzzle end is cut square across (the level photo shows the side faces' tips 0.1 in ahead of the rail's end, most of which is where the lens stood). The rail's head is MIL-STD-1913's (sellers: \"M1913 picatinny rail\"), its lower faces run in to the neck's walls 0.22 in below its top (a photo of a shorter rail reads 0.18), and its slots are the standard's.","Inside it is the sellers' 1.26 in: a round bore from the rear face to the first M-LOK slot (how far the round part really runs isn't seen), then flat inner walls that touch that circle and follow the outside, as the photos of the muzzle end show them, the bottom's wall as thick as the sides' 0.165 in; the channel under the rail runs its whole length, open into the tube.","Eight M-LOK slots on each side face and each lower face and seven on each upper face, at the standard's size and pitch, each row at the height the level photo shows it. The underside's row is drawn at the side rows' stations with their count of eight: assumed. Sellers say \"M-LOK slots on every quadrant\", but no photo shows the bottom, so how many slots it has and where they begin isn't seen; the side rows' rearmost slot begins 0.05 in ahead of the clamp block's front, so the eight stand ahead of the block and its split.","The clamp block under the rear end is the traced outline's shape below the tube, as wide as the side faces (the rear view of the shorter rail shows it so within 3%), its front a flat wall where the outline's ramp ends, split along its underside by a channel 0.51 in wide that is carried from the rear face to the ramp (its real length isn't seen). The two cross bolts are holes right across with the bolts' heads in counterbores on the right, cut as deep as the holes are wide (their depth isn't seen); the nut plate on the left is drawn with round ends and a straight bar, a groove of 0.024 in round it.","Behind the rear face: a lower tab each side, 0.26 in long, as thick as the side walls (their thickness isn't seen), with a set screw's hole across its middle; and a short upper tab each side under the rail, 0.12 in long, drawn as the section's own outside carried back with the opening between the two taken as a mil-spec receiver's flat sides (0.638 in: the opening isn't seen square on). On the catalog's BCM receiver the right lower tab's top edge stands 0.03 in into the round of the port door's front hinge lug, inside what the two readings carry (the tab's top by a photo, ± 0.02; the lug by the reference model). Each sling swivel socket is its hole through the upper face with a shallow step for the cup; the steel cup is a plain ring in the step, standing half the edge break proud of the face (its four notches and its lip inside aren't drawn).","It is drawn with its rear face against the receiver's front shoulder: no page read says where it stops and no photo of it mounted is on file. Its rail's first slot then stands 0.04 in ahead of where the receiver's own slots would continue.","The steel on it is drawn as pieces of their own, so that it keeps its colour on a rail of another: the nut plate in its seat, the two bolts as plain rounds, their heads in the counterbores and their shanks across the split to end the edge break inside the plate's holes (their Torx sockets and threads aren't drawn), and a set screw in each lower tab as a plain round, flush less the edge break (the photos have them standing out of the tabs, unseated, as shipped).","Not drawn: its barrel nut (inside it, against the receiver: an olive gold in the photos of both colours), the engraving on its right side (GEISSELE AUTOMATICS / NORTH WALES, PA) and the marks in the rail's slots.","Its aluminium by the model is 9.99 cubic inches, 15.7 oz: nearer the sellers' 15.6 oz for the handguard alone than their 14.2. The steel drawn on it (the two bolts, the nut plate, the set screws, the two cups: 0.14 cubic inches) would be 0.6 oz more; whether the sellers' figure has it isn't said."],"ledger":["geissele-mk16-15-handguard.length","geissele-mk16-15-handguard.width","geissele-mk16-15-handguard.height","geissele-mk16-15-handguard.inside_diameter","geissele-mk16-15-handguard.rear_x"]},"profiles":{"side":{"plane":"xy","origin":"the lower tabs' rear ends (behind the rear face) and the rail's top","offset":{"x":"rear_x","y":"rail_top_above_bore"},"points":[[0,-1.538],[0.008,-1.819],[0.065,-1.853],[0.33,-1.853],[0.368,-1.914],[0.467,-1.951],[0.486,-1.978],[0.478,-2.16],[0.509,-2.312],[0.573,-2.377],[0.672,-2.407],[1.052,-2.399],[1.188,-2.324],[1.279,-2.301],[2.251,-2.293],[2.327,-2.263],[2.411,-2.179],[2.434,-2.179],[2.57,-2.096],[2.654,-2.073],[15.107,-2.027],[15.137,-2.012],[15.156,-1.978],[15.27,-1.447],[15.27,-0.877],[15.141,-0.505],[15.141,-0.171],[15.156,-0.087],[15.137,-0.068],[14.947,0],[14.727,0],[14.553,-0.023],[14.518,-0.042],[14.492,-0.114],[14.473,-0.027],[14.446,0],[14.294,0],[14.15,-0.03],[14.12,-0.114],[14.101,-0.103],[14.093,-0.034],[14.067,0],[13.907,0],[13.778,-0.03],[13.759,-0.049],[13.748,-0.114],[13.721,-0.11],[13.695,0],[13.527,0],[13.421,-0.023],[13.395,-0.042],[13.368,-0.114],[13.334,-0.11],[13.334,-0.065],[13.307,0],[13.148,0],[13.026,-0.03],[12.996,-0.114],[12.954,-0.11],[12.939,-0.027],[12.912,0],[12.761,0],[12.685,-0.023],[12.635,-0.049],[12.624,-0.114],[12.567,-0.11],[12.559,-0.034],[12.54,0],[12.381,0],[12.282,-0.03],[12.256,-0.049],[12.244,-0.114],[12.18,-0.11],[12.172,-0.027],[12.145,0],[12.001,0],[11.902,-0.03],[11.876,-0.065],[11.865,-0.114],[11.792,-0.103],[11.785,-0.027],[11.758,0],[11.629,0],[11.523,-0.03],[11.504,-0.049],[11.492,-0.114],[11.413,-0.11],[11.386,0],[11.287,0],[11.166,-0.023],[11.124,-0.049],[11.113,-0.114],[11.029,-0.114],[11.018,-0.034],[10.984,0],[10.877,0],[10.786,-0.023],[10.752,-0.049],[10.741,-0.114],[10.642,-0.114],[10.631,-0.027],[10.604,0],[10.483,0],[10.407,-0.023],[10.372,-0.049],[10.361,-0.114],[10.255,-0.114],[10.232,-0.008],[10.095,0],[9.997,-0.038],[9.974,-0.121],[9.867,-0.114],[9.856,-0.019],[9.807,0],[9.678,-0.008],[9.647,-0.023],[9.613,-0.057],[9.613,-0.095],[9.643,-0.11],[9.594,-0.121],[9.48,-0.114],[9.457,-0.008],[9.29,-0.008],[9.233,-0.057],[9.233,-0.095],[9.245,-0.084],[9.271,-0.11],[9.214,-0.121],[9.101,-0.121],[9.082,-0.019],[9.04,0],[8.888,-0.023],[8.854,-0.065],[8.869,-0.065],[8.873,-0.099],[8.892,-0.087],[8.892,-0.11],[8.835,-0.121],[8.706,-0.121],[8.683,-0.008],[8.508,-0.015],[8.482,-0.042],[8.482,-0.072],[8.512,-0.11],[8.463,-0.121],[8.318,-0.121],[8.296,-0.008],[8.129,-0.015],[8.117,-0.027],[8.125,-0.11],[8.083,-0.121],[7.931,-0.121],[7.908,-0.008],[7.741,-0.015],[7.726,-0.121],[7.536,-0.121],[7.525,-0.019],[7.506,-0.008],[7.354,-0.015],[7.339,-0.121],[7.149,-0.121],[7.126,-0.008],[6.967,-0.008],[6.952,-0.121],[6.754,-0.121],[6.75,-0.027],[6.724,-0.008],[6.587,-0.008],[6.568,-0.034],[6.564,-0.121],[6.367,-0.121],[6.344,-0.008],[6.192,-0.008],[6.177,-0.121],[5.972,-0.121],[5.965,-0.015],[5.805,-0.008],[5.782,-0.121],[5.653,-0.129],[5.573,-0.11],[5.573,-0.019],[5.562,-0.008],[5.41,-0.008],[5.387,-0.121],[5.19,-0.121],[5.175,-0.008],[5.023,-0.008],[5.004,-0.027],[5.004,-0.118],[4.955,-0.129],[4.795,-0.121],[4.791,-0.019],[4.765,-0.008],[4.628,-0.008],[4.605,-0.121],[4.408,-0.121],[4.397,-0.11],[4.404,-0.027],[4.385,-0.008],[4.241,-0.008],[4.222,-0.027],[4.214,-0.118],[4.157,-0.129],[4.013,-0.121],[4.009,-0.027],[3.937,-0.008],[3.831,-0.015],[3.819,-0.118],[3.77,-0.129],[3.618,-0.121],[3.63,-0.103],[3.614,-0.095],[3.614,-0.019],[3.595,-0.008],[3.444,-0.015],[3.413,-0.129],[3.239,-0.121],[3.235,-0.057],[3.25,-0.042],[3.227,-0.042],[3.223,-0.106],[3.22,-0.027],[3.163,-0.008],[3.056,-0.008],[3.037,-0.027],[3.018,-0.129],[2.866,-0.121],[2.866,-0.106],[2.847,-0.103],[2.87,-0.095],[2.87,-0.049],[2.836,-0.038],[2.829,-0.076],[2.825,-0.027],[2.768,-0.008],[2.654,-0.015],[2.635,-0.057],[2.631,-0.129],[2.502,-0.129],[2.472,-0.046],[2.396,-0.015],[2.282,-0.008],[2.248,-0.027],[2.229,-0.129],[2.115,-0.129],[2.092,-0.046],[2.016,-0.015],[1.917,-0.008],[1.853,-0.027],[1.834,-0.129],[1.72,-0.129],[1.708,-0.057],[1.614,-0.015],[1.469,-0.015],[1.45,-0.034],[1.443,-0.125],[1.424,-0.137],[1.333,-0.129],[1.321,-0.057],[1.219,-0.015],[1.067,-0.015],[1.044,-0.129],[0.9,-0.129],[0.888,-0.087],[0.904,-0.072],[0.881,-0.049],[0.888,-0.042],[0.839,-0.023],[0.345,-0.015],[0.319,-0.08],[0.342,-0.345],[0.334,-0.452],[0.323,-0.471],[0.194,-0.471],[0.159,-0.543],[0.144,-0.634],[0.156,-0.661],[0.178,-0.668],[0.296,-0.672],[0.258,-0.885],[0.251,-1.469],[0.042,-1.473],[0.008,-1.507]],"scaleRefs":["geissele-mk16-15-handguard.overall_length","geissele-mk16-15-handguard.height"],"inputs":{"geissele-mk16-15-handguard.height":2.39,"geissele-mk16-15-handguard.overall_length":15.38},"tolerance":0.01,"photo":"references/geissele-mk16-15-handguard 2b07184f9c79 (Primary Arms' gallery for 05-792B, 05-792B_02.jpg: the handguard alone, its left side seen level, muzzle to the left, 2200 x 1467)","method":"luminance < 200, largest piece, holes filled; scale from geissele-mk16-15-handguard.overall_length = 15.38 in (x-extent 2011 px → 130.8 px/in) and geissele-mk16-15-handguard.height = 2.39 in (y-extent 317 px → 132.6 px/in), which agree within 1.4%; mean 131.7 px/in; origin at x min, y max of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 283 points (IoU 0.997 with the full outline) (tools/trace.py)","via":"harvest","note":"The slots are inside the outline (filled); the model cuts them. Its left side, mirrored: the plate with two holes is this side's, the bolt heads the other's. The outline's scale is the photo's mean; at the rear end the photo is 1.3% larger, so the clamp block reads 0.03 in long."}},"gaps":[{"what":"The M-LOK slots on its underside: how many, and where they begin (sellers: \"M-LOK slots on every quadrant\"; drawn and offered as the side rows' eight at the side rows' stations, assumed)","need":"A photo of it from below: no view on file shows the bottom face"},{"what":"Where it stops on the receiver (rear_face_x: drawn against the front shoulder with no gap)","need":"A photo of it mounted on a mil-spec upper, or the maker's instruction sheet from a page that may be read"},{"what":"Its section square on at this length (the faces' angle, the neck's width, the walls)","need":"An end view of the 15 in rail with a known size in frame; the only near end-on view is of a shorter rail, 504 px wide"},{"what":"Its weight: sellers give 15.6 oz (17.1 with the nut) and 14.2 oz (15.8)","need":"The maker's own figure, from a page that may be read"},{"what":"The room inside its faces before the barrel (reach_inside: what an M-LOK accessory's nuts may take)","need":"The barrel's and the gas block's size under it, from the parts a build puts there"},{"what":"Its Desert Dirt Color as the maker means it (05-792S is matched to one seller's rail; the maker says the colour varies from rail to rail)","need":"The maker's own pictures of the DDC rail, from a page that may be read"}]},"geissele-premium-mil-spec-buffer-tube-assembly-castle-nut":{"id":"geissele-premium-mil-spec-buffer-tube-assembly-castle-nut","name":"Premium Mil-Spec Buffer Tube Assembly, castle nut","manufacturer":"Geissele Automatics","url":"https://charliescustomclones.com/geissele-premium-mil-spec-buffer-tube-assembly-gray/","category":"castle_nut","description":"The nut on the receiver extension's thread that is turned down onto the end plate and locks the extension to the lower receiver, its four wrench notches in its rear face and a staking notch in its front face's edge, in Geissele's Premium Mil-Spec Buffer Tube Assembly. Its sellers: \"Included in the package is a high-quality, mil-spec castle nut and end plate\" (Mile High Shooting, Midwest Optics, Charlie's Custom Clones). Not sold alone on any page read, and named by none: the name is the catalog's. A buyer of the DDC at Primary Arms (08-162S, 2025-04-22): \"the [in]cluded castle nut and end plate is total trash. My set I found pit marks, poor finish, and poor casting\": a buyer's word, kept as it was said.","weight":"geissele-premium-mil-spec-buffer-tube-assembly-castle-nut.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"seat":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the tube axis at the nut's front face, which bears on the end plate, +x rearward."}},"interfaces":{"nut_seat":{"type":"ar15.end_plate_seat","role":"nut","anchor":"seat","params":{},"flips":false,"note":"Its sellers: \"mil-spec castle nut and end plate\"."}},"materials":{"nut":{"label":"Castle nut","finish":"phosphate","recolorable":false,"color":"steel-phosphate-charcoal","note":"No page says what it is made of or finished in. Its look is a matte steel's phosphate, the end plate's, one look in every colourway of the tube: a mid charcoal grey in Geissele's own studio pictures, whatever the tube's colour (the gray assembly, 234b20bbfb70; the ODG with a Super 42, 2cac1d3a530d; the DDC on Charlie's page, 3bb361da6107; the black on Mile High's, b28e8bf12ad3), a near black in Primary Arms' (40caefb1150b, a41d12311be2), a dark grey with a lighter mottle on the black assembly in Charlie's picture under one light (7564882554c6). Drawn in the steel presets' charcoal phosphate (data/colors/steel.yaml), as the end plate is; not fitted on its own."}},"components":{},"geometry":{"model":"geissele-premium-mil-spec-buffer-tube-assembly-castle-nut.glb","components":{},"approximations":["The mil-spec nut as the AR-15 CAD reference set draws it (its outside, its thickness, its notches' sizes, three staking notches): every seller calls it mil-spec and every photo of it on file has a mil-spec nut's four wrench notches and a staking notch in its front edge. Its outside, read beside the tube in Charlie's picture of five, agrees within its ±.","A ring bored to the extension's thread's crests (std.receiver_extension.thread_major_d), as the other nuts on file are drawn: its own thread isn't drawn, and the bore's chamfers aren't.","The four wrench notches are cut straight through the wall from the bore, square-floored, a quarter turn apart; one wrench notch and one staking notch are put at the top, in line, as the flat-lay photo has one of each at its near side. How a nut is turned on its thread isn't fixed."],"ledger":["geissele-premium-mil-spec-buffer-tube-assembly-castle-nut.od","geissele-premium-mil-spec-buffer-tube-assembly-castle-nut.thickness","geissele-premium-mil-spec-buffer-tube-assembly-castle-nut.notches","geissele-premium-mil-spec-buffer-tube-assembly-castle-nut.notch_width","geissele-premium-mil-spec-buffer-tube-assembly-castle-nut.notch_depth","geissele-premium-mil-spec-buffer-tube-assembly-castle-nut.staking_notches"]},"profiles":{},"gaps":[{"what":"What it is: its maker, its number, its steel and its finish","need":"Geissele's own page of the assembly (geissele.com refuses the reader: one the user saves), or a seller's page that names the nut"},{"what":"Its thickness","need":"a photo of the nut square from the side, or on the tube with the tube square to the lens"}]},"geissele-premium-mil-spec-buffer-tube-assembly-end-plate":{"id":"geissele-premium-mil-spec-buffer-tube-assembly-end-plate","name":"Premium Mil-Spec Buffer Tube Assembly, end plate","manufacturer":"Geissele Automatics","url":"https://charliescustomclones.com/geissele-premium-mil-spec-buffer-tube-assembly-gray/","category":"end_plate","description":"The plate between the castle nut and the lower receiver in Geissele's Premium Mil-Spec Buffer Tube Assembly: a ring round the receiver extension with a lobe that covers the takedown pin's detent spring, a key in its hole that rides in the extension's slot, and an obround boss on the lobe. Charlie's Custom Clones: \"Included in the package is a high-quality, mil-spec castle nut and end plate\"; \"Includes end plate and castle nut (does not include buffer or spring, which is needed)\"; Mile High Shooting and Midwest Optics the same words of the black and the ODG. Not sold alone on any page read, and named by none: the name is the catalog's. A buyer of the DDC at Primary Arms (08-162S, a review of 2025-04-22): \"the [in]cluded castle nut and end plate is total trash. My set I found pit marks, poor finish, and poor casting. The endplate looks fresh out the forge no milling just coated\": a buyer's word, kept as it was said.","weight":"geissele-premium-mil-spec-buffer-tube-assembly-end-plate.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"end":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the tube axis at the plate's front face, which bears on the receiver's rear face, +x rearward."},"nut_seat":{"origin":["{.thickness}",0,0],"x":[1,0,0],"note":"The plate's rear face, where the castle nut bears."}},"interfaces":{"extension_end":{"type":"ar15.extension_end","role":"fitting","anchor":"end","params":{},"flips":false,"note":"Charlie's: \"mil-spec castle nut and end plate\"."},"nut_seat":{"type":"ar15.end_plate_seat","role":"plate","anchor":"nut_seat","params":{},"flips":false}},"materials":{"plate":{"label":"End plate","finish":"phosphate","recolorable":false,"color":"steel-phosphate-charcoal","note":"No page says what it is made of or finished in. Its look is a matte steel's phosphate, one look in every colourway of the tube: a mid charcoal grey in Geissele's own studio pictures, whatever the tube's colour (the gray assembly, 234b20bbfb70; the ODG with a Super 42, 2cac1d3a530d; the DDC on Charlie's page, 3bb361da6107; the black on Mile High's, b28e8bf12ad3), a near black in Primary Arms' (the black and the DDC tube's, 40caefb1150b, a41d12311be2), and a dark grey on the assembled tubes in Charlie's picture under one light (7564882554c6). Drawn in the steel presets' charcoal phosphate (data/colors/steel.yaml), between the two studios' readings; not fitted on its own."}},"components":{},"geometry":{"model":"geissele-premium-mil-spec-buffer-tube-assembly-end-plate.glb","components":{},"approximations":["The mil-spec plate as the AR-15 CAD reference set draws it (its ring, its lobe and straight sides, its hole with the key and the V either side, its obround boss and the dimple behind it, its thickness): Charlie's calls the assembly's plate mil-spec, and every photo of it on file has that outline. The one size a photo gives square across, the ring's width on Primary Arms' 08-162B_03, agrees within its ±.","Its thickness, the boss's and the dimple's depths: the reference model's; no photo on file shows the plate edge on.","Not drawn: the staking points, and the edge a stamping leaves rounded on one face and sharp on the other (both edges are broken alike).","Its boss stands 0.065 in out of its front face, into the receiver's rear face where the takedown pin's detent spring is: no lower in the catalog has that recess drawn, so the two models share that much, as the other mil-spec plates do."],"ledger":["geissele-premium-mil-spec-buffer-tube-assembly-end-plate.thickness","geissele-premium-mil-spec-buffer-tube-assembly-end-plate.height","geissele-premium-mil-spec-buffer-tube-assembly-end-plate.top_above_axis","geissele-premium-mil-spec-buffer-tube-assembly-end-plate.bottom_below_axis","geissele-premium-mil-spec-buffer-tube-assembly-end-plate.lobe_radius","geissele-premium-mil-spec-buffer-tube-assembly-end-plate.lobe_centre_below_axis"]},"profiles":{},"gaps":[{"what":"What it is: its maker, its number, its steel and its finish","need":"Geissele's own page of the assembly (geissele.com refuses the reader: one the user saves), or a seller's page that names the plate"},{"what":"Its sizes","need":"a square-on picture of the plate with a scale: every size here is the reference model's mil-spec plate, which the photos on file agree with"}]},"geissele-premium-mil-spec-buffer-tube":{"id":"geissele-premium-mil-spec-buffer-tube","name":"Premium Mil-Spec Buffer Tube","manufacturer":"Geissele Automatics","sku":"08-162B","url":"https://www.milehighshooting.com/geissele-premium-mil-spec-buffer-tube/","category":"receiver_extension","description":"Geissele's mil-spec carbine buffer tube, six positions, 7075-T6 under a Type 3 hardcoat anodize in black, Desert Dirt, OD green or gray. Its sellers, in the words they share: \"The Geissele Premium Mil-Spec Buffer Tube is machined from quality 7075-T6 Aluminum and finished in Type 3 Hardcoat Anodize, available in Black, Geissele's DDC, and ODG. This rigid and durable buffer tube conforms to all mil-spec standards and features 6 stock positions. This carbine length and mil-spec diameter Premium Buffer Tube is made in the USA and weighs in at 3.7oz\" (Mile High Shooting, Midwest Optics, Charlie's Custom Clones). Charlie's sells it with \"a high-quality, mil-spec castle nut and end plate\" as an assembly in gray and DDC: \"Forged 7075-T6 buffer (extension) tube Mil-spec diameter, carbine length 6-position for collapsible stocks Fits most all AR15 lowers, including M4 lower receivers Type 3 hardcoat anodized, gray color Geissele logo\". Every seller's package has the nut and the plate in it (\"Included in the package is a high-quality, mil-spec castle nut and end plate\": Mile High, Midwest Optics, Charlie's; Primary Arms' photos): the tube isn't sold without them, and they are parts of their own here. Its rail comes down to full depth by a long ramp, with a shallow strip ahead of it, and a channel with round ends runs along the rail's underside through its six holes; Geissele's logo is on the rail's right side at the rear.","weight":"geissele-premium-mil-spec-buffer-tube.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"receiver_thread":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the tube axis at the takedown pin's X, +x rearward."},"tube":{"origin":[0,0,0],"x":[1,0,0]},"end":{"origin":["0in - {std.ar15.receiver_rear_x}",0,0],"x":[1,0,0],"note":"On the tube axis at the receiver's rear face (the Army's drawing of the lower), where an end plate bears."},"bore":{"origin":["0in - {std.ar15.upper_rear_face_x}",0,0],"x":[1,0,0],"note":"On the tube axis where a buffer's front face rests with the bolt forward: against the carrier's rear end, which stands at the upper receiver's rear face (the Army's drawings). The buffer and its spring are placed from it."}},"interfaces":{"receiver_thread":{"type":"ar15.buffer_tube_mount","role":"tube","anchor":"receiver_thread","params":{},"flips":false,"note":"Charlie's: \"Fits most all AR15 lowers, including M4 lower receivers\"; Primary Arms: \"Platform AR-15/AR-308\" (the AR-10's is another tube; on file only the AR-15's lower)."},"tube":{"type":"receiver_extension","role":"tube","anchor":"tube","params":{"profile":"mil-spec","od":"={.tube_od}","positions":6,"step":"={.position_step}"},"flips":false,"note":"Sold as mil-spec, six positions: \"Mil-spec diameter, carbine length 6-position for collapsible stocks\" (Charlie's); \"6-position Mil-Spec carbine buffer tube\" (Primary Arms); \"Precision machining and Mil-Spec tolerances ensure a tight, rattle-free fit with virtually any Mil-Spec stock on the market\" (Primary Arms)."},"extension_end":{"type":"ar15.extension_end","role":"tube","anchor":"end","params":{},"flips":false},"bore":{"type":"ar15.extension_bore","role":"tube","anchor":"bore","params":{},"flips":false,"note":"Charlie's: \"a six position Mil-Spec size for carbine springs and buffers\"."}},"materials":{"tube":{"label":"Receiver extension","finish":"anodized","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized","color":"placeholder-black","sku":"08-162B","source":"https://www.milehighshooting.com/geissele-premium-mil-spec-buffer-tube/"},"ddc":{"label":"Desert Dirt Color (DDC)","finish":"anodized","color":"geissele-ddc-buffer-tube","sku":"08-162S","source":"https://www.primaryarms.com/geissele-automatics-premium-mil-spec-ar15-buffer-tube-desert-dirt"},"gray":{"label":"Gray","finish":"anodized","color":"geissele-gray-buffer-tube","sku":"08-162G","source":"https://charliescustomclones.com/geissele-premium-mil-spec-buffer-tube-assembly-gray/"}},"default":"black","note":"One piece of 7075 aluminium under a hardcoat anodize in the colour it is sold in: \"machined from quality 7075-T6 Aluminum and finished in Type 3 Hardcoat Anodize\" (Mile High Shooting, Midwest Optics, Charlie's), \"Type III hardcoat anodized finish\" (Primary Arms), hence `anodized`. Sold in four colours, each its own number: Black 08-162B, DDC 08-162S, ODG 08-162ODG, and the gray, whose number 08-162G no page writes out in its text: it is the mpn in the markup of Charlie's Custom Clones' page of the gray assembly (its own SKU G081637, UPC 817953029893), and the name of Geissele's own picture of the gray tube on that page (08-162g_grey_buffer_tube_040621_h1). Every seller's page that lists Geissele's colours names three (\"available in Black, Geissele's DDC, and ODG\": Mile High, Midwest Optics, and Charlie's own gray page): no page read says whether Geissele still makes the gray, or that it is discontinued (OpticsPlanet was said by a search summary to call it discontinued; its page wasn't read). Charlie's had one in stock on 2026-11-03 (\"Availability: ships from our shop in 5 to 8 days\"). Of the colour itself the sellers say it varies: Charlie's, \"You will notice that some of these will have wildly different shades of colored anodizing ... Black is easy. Gray is hard. Keep in-mind that gray in your mind is different than gray in the head of the next person\"; Primary Arms of DDC, \"These colors can vary drastically, even between products from the same batch, and are not intended to color match\". The gray is fitted on Geissele's own studio photograph of the gray tube, the DDC on Primary Arms' of the DDC tube (data/colors/geissele.yaml). The ODG (08-162ODG, Midwest Optics' page, out of stock when read) is sold and isn't offered: the one picture of it on file (2cac1d3a530d, Geissele's 08-163ODG-H3 on Midwest Optics' page) is the same photograph as Mile High's picture of the black assembly (b28e8bf12ad3) with the tube recoloured: their nut and plate agree pixel for pixel (a luminance correlation of 0.99 after one scale and shift) and the tube's thread crests stand in the same places (0.94), where two shots of two tubes would put the crests where each tube's turn left them. Which of the two is the photograph isn't known; the black is the finish's look either way. The castle nut and the end plate are their own parts and slots, the same in every colourway (the assembly's kit)."},"mark":{"label":"Geissele's mark","finish":"anodized_matte","recolorable":false,"color":"geissele-laser-mark","note":"\"GEISSELE\" over \"AUTOMATICS\" on the rail's right side at its rear, laser marked: white through the anodize in every photo on file, whatever the tube's colour (the black, c5f8fd0417ad, #b2b6b6; the gray, 234b20bbfb70, #e5e0de; the DDC, fbfef3f8409d, #fcfbf7), so one look in every colourway. Charlie's: \"Geissele logo\"."}},"components":{},"geometry":{"model":"geissele-premium-mil-spec-buffer-tube.glb","components":{},"approximations":["The tube is the mil-spec carbine extension's where the sellers say it is (\"Mil-spec diameter, carbine length\"): its outside the standard's 1.148, its length Magpul's drawing's 7.25 (Geissele's own on Primary Arms' photo, scaled by its thread, reads 7.26), its front face where the Army's drawings put a mil-spec tube's, its thread the standard's 1 3/16-16 (a helix between the Army drawing's limits) to the length Geissele's shows (1.29 in from the front face), bored to the drawing's inch to a rear wall of the reference model's 0.072 with its 0.094 hole. No view on file shows Geissele's rear end or its mouth inside: the reference model's wall and hole are assumed for them.","The rail is the standard's in section (Magpul's drawing: its width, its depth below the axis) and Geissele's own along its length, read on two photos: full depth from the rear face to 2.90 in behind the front face, a straight ramp to 2.42 (about 30 degrees, where the drawing's is 45), and ahead of it a strip of the rail's width whose floor is 0.59 below the axis, just proud of the tube, to a square end 1.51 behind the front face.","Along the rail's underside a channel with round ends, from the rear hole's centre to the front one's, as wide as the holes (both read on the DDC tube's underside); its depth (0.05) is assumed. The six holes are drilled up from its floor to the tube's outside (their depth is assumed: what each has in its floor, a small hole 0.115 across, isn't drawn).","The key slot at six o'clock under the thread is the standard's in width and floor (the reference model's), and Geissele's own in length (1.00 from the front face, on the DDC tube's underside).","The mouth's plain lip ahead of the first crest is drawn at the thread's roots. The tube's rear outer edge is broken 0.06 at 45 degrees (the side photo's corner); every other edge by the script's small round.","Geissele's mark is drawn on the rail's right side in a slot of its own (white, as laser marked through the anodize), each of its two lines in Blender's own typeface thickened and slanted as the photo's, scaled to the line's measured length and capital height at its measured place: Geissele's own lettering isn't on file. No photo on file shows the rail's left side: nothing is drawn there.","Not drawn: the small holes in the position holes' floors, the rail's edge breaks, any chamfer in the mouth."],"ledger":["geissele-premium-mil-spec-buffer-tube.tube_od","geissele-premium-mil-spec-buffer-tube.tube_length","geissele-premium-mil-spec-buffer-tube.tube_front_behind_pin","geissele-premium-mil-spec-buffer-tube.position_step","geissele-premium-mil-spec-buffer-tube.position_hole_d","geissele-premium-mil-spec-buffer-tube.position_hole_rear_from_rear","geissele-premium-mil-spec-buffer-tube.channel_width","geissele-premium-mil-spec-buffer-tube.channel_depth","geissele-premium-mil-spec-buffer-tube.rail_full_from_front","geissele-premium-mil-spec-buffer-tube.ramp_top_from_front","geissele-premium-mil-spec-buffer-tube.land_front_from_front","geissele-premium-mil-spec-buffer-tube.land_bottom_below_axis","geissele-premium-mil-spec-buffer-tube.thread_length","geissele-premium-mil-spec-buffer-tube.mouth_lip","geissele-premium-mil-spec-buffer-tube.key_slot_length","geissele-premium-mil-spec-buffer-tube.rear_edge_break","geissele-premium-mil-spec-buffer-tube.mark_length","geissele-premium-mil-spec-buffer-tube.mark_height","geissele-premium-mil-spec-buffer-tube.mark_slant"]},"profiles":{},"gaps":[{"what":"Whether Geissele still makes the gray (08-162G)","need":"Geissele's own page of the tube (geissele.com refuses the reader: one the user saves from their browser), or a dealer's page that says it is current or discontinued"},{"what":"Every size of Geissele's own: read on Primary Arms' two studio photos (a side view and an underside), each scaled by the tube itself","need":"a drawing of Geissele's tube, or a third photo square to the rail's side with a known size in its plane"},{"what":"The rear end, the channel's depth, the holes' depth and what is in their floors","need":"a photo of the rear end square on, and one of the rail's underside along it"},{"what":"The colours rest on one photograph each, the gray on Geissele's own studio picture of one tube","need":"a second studio's photograph of each colour with a known neutral in frame; the gray varies from lot to lot by Charlie's own picture of five"}]},"geissele-ssa-e":{"id":"geissele-ssa-e","name":"Super Semi-Automatic Enhanced (SSA-E) Trigger","manufacturer":"Geissele Automatics","sku":"05-160","url":"https://www.milehighshooting.com/geissele-super-semi-automatic-enhanced-ssa-e-trigger/","category":"trigger","description":"Geissele's two-stage trigger group with the curved M4 bow: trigger, hammer, disconnector, their springs and two pins. Mile High Shooting's page (it carries the number 05-160): \"Built on the chassis of the Geissele SSA®, the Super Semi-Automatic Enhanced® (SSA-E®) provides enhanced trigger control and weapon accuracy while maintaining the robustness and reliability of Geissele's combat-proven two-stage trigger.\"; \"1st STAGE WEIGHT RANGE: 2.0 - 2.5 lbs. 2nd STAGE WEIGHT RANGE: 0.9 - 1.3 lbs. TOTAL PULL WEIGHT RANGE: 2.9 - 3.8 lbs. ADJUSTABLE: No TRIGGER BOW TYPE: M4 Curved PIN SIZE: Mil-Spec\". Primary Arms: \"EDM wire cut from heavy-duty tool steel with a durable black finish\". The page linked is a seller's: the maker's own site isn't read (it refuses the reader).","weight":"geissele-ssa-e.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"fcg":{"origin":[0,0,0],"note":"The trigger pin's axis."},"face":{"origin":["{.face_offset_x}",0,0],"note":"The bow's face, where length of pull is read: its front edge halfway down what shows below a receiver, at rest."}},"interfaces":{"fcg":{"type":"ar15.fcg","role":"trigger","anchor":"fcg","params":{"pin_diameter":"small-pin"},"flips":false,"note":"Primary Arms (MPN 05-160): \"Standard .154\\\" mil-spec trigger and hammer pins fit any mil-spec stripped lower receiver\". Mile High Shooting, in the maker's voice: \"Please note , our triggers are designed for mil-spec AR15/M4 carbine rifles. Our AR15 triggers are not compatible with the Sig MPX/MCX weapons or Pistol Caliber Carbine AR15/M4 variants. Using them in these platforms will void the warranty.\" (BCM's page says the same of \"Geissele's triggers\"). A large-pin trigger is another number, not on file."}},"materials":{"body":{"label":"Trigger, hammer, disconnector and pins","finish":"steel","recolorable":false,"color":"geissele-black-oxide","note":"One colour, no colour numbers: black on every page read (\"a durable black finish\", Primary Arms; \"Black Oxide Finish\" in the title of one distributor-fed page, Selway Armory, the only page to name a process). Piece by piece on Primary Arms' two photos (86bac1cc4a94, ca0156d76566) and the maker's parts view at BCM (1bf5dd1b0dab): the trigger, the hammer and the disconnector are one matte charcoal on their flats, and the two pins the same dark steel (they read lighter where a light lies along them), so the group is one material. It is matched as a colour, not left at the placeholder black: the flats read #41413f to #525252 where black anodize and black Melonite read #282828 to #363439 in the same studio. Not drawn, and of other colours: the hammer spring (a grey-brown wire), the trigger and disconnector springs (bright wire), the bright slave pin Primary Arms' photo shows beside the parts, the white-filled engraving."}},"components":{"body":{"label":"Trigger","material":"body"}},"geometry":{"model":"geissele-ssa-e.glb","components":{},"approximations":["Three pieces are drawn, each from its own outline in one picture of the group assembled and cocked (the maker's artwork on a seller's page, square to its right side), scaled and levelled by its two pins' ends, which a receiver holds 0.9 in apart: the trigger, the hammer where the trigger holds it cocked, and what shows of the disconnector above the trigger's tail. The three springs aren't drawn.","The two pins are plain rounds at the published .154 in, as long as BCM's picture of the parts shows them lying (0.83 in): the groove at each one's middle and the one near its end aren't drawn.","Each piece is its outline at one width across, read off BCM's picture of the parts lying apart: the trigger's body 0.25 in, the block at its front 0.305, its bow 0.265, the hammer 0.22, the disconnector 0.17. Their edges are square: the bevels along the block's lower edges, the rounding of the bow's face and the makers' marks cast into the sides aren't drawn.","The bosses round the two pin holes are plain rounds at the diameters the parts view shows (0.29 and 0.25 in), drawn to the span of a mil-spec trigger's (std.ar15.trigger_boss_length, 0.664 in, inside a pocket .690 wide): Geissele's own span isn't read, for the trigger or the hammer.","Where one piece lies against another the line between them is picked by hand on the picture, dark on dark: the trigger's top under the disconnector and under the trigger spring's coil (a straight line from the tail's top to the sear's foot), the top of its front block under the hammer, the hammer's underside over that block, and where the hammer's hook sits on the sear.","The hammer is drawn cocked, as the picture has it: its head stands 0.23 in above a lower's deck, in the space under the bolt carrier. An upper receiver's model that is solid there holds it (0.012 to 0.017 cubic inches of it in the catalog's four uppers, 2026-10-06); nothing of that shows from outside, and it isn't cut from either.","The small hole through the hammer above its spring's shelf is cut where the side picture has it (0.078 in); what shows in it there (a pin's end, by its look) isn't drawn.","The hammer's outline has its spring on it: the bent end of the spring's upper leg, hooked under the hammer's shelf, is in it (0.04 by 0.06 in). The disconnector is drawn to where the trigger spring's coil hides it, 0.19 in behind the pin it turns on, with its underside taken as the tail's top (its spring shows between the two).","The outlines are the older production's (engraved U.S. PAT. 7600338); the widths are read on the current one's (PATENT: GEISSELE.COM/PATENTS), whose outline is the same by eye and fills the same box within 1% in the parts view."],"ledger":["geissele-ssa-e.face_offset_x","geissele-ssa-e.shoe_face_x"]},"profiles":{"side":{"plane":"xy","origin":"the trigger pin's axis (the trigger frame's origin), +x toward the muzzle, the hammer's pin where a receiver has it: at rest, cocked","offset":{},"points":[[-1.097,-0.216],[-1.097,-0.247],[-1.085,-0.273],[-1,-0.284],[-0.992,-0.278],[-0.954,-0.278],[-0.875,-0.285],[-0.037,-0.288],[-0.029,-0.298],[-0.027,-0.365],[0,-0.412],[0.001,-0.446],[-0.046,-0.555],[-0.078,-0.685],[-0.087,-0.805],[-0.087,-0.89],[-0.077,-0.962],[-0.044,-1.083],[0.012,-1.213],[0.083,-1.318],[0.138,-1.385],[0.162,-1.403],[0.177,-1.403],[0.195,-1.393],[0.212,-1.37],[0.217,-1.35],[0.161,-1.258],[0.119,-1.168],[0.095,-1.077],[0.086,-0.998],[0.085,-0.931],[0.094,-0.855],[0.108,-0.797],[0.137,-0.721],[0.197,-0.614],[0.275,-0.524],[0.344,-0.467],[0.363,-0.467],[0.378,-0.458],[0.381,-0.437],[0.403,-0.437],[0.463,-0.406],[0.492,-0.383],[0.498,-0.372],[0.506,-0.215],[0.524,-0.208],[0.748,-0.213],[0.761,-0.203],[0.772,-0.168],[0.779,0.005],[0.781,0.02],[0.788,0.025],[0.78,0.05],[0.517,0.049],[0.515,0.137],[0.443,0.137],[0.378,0.155],[0.322,0.158],[0.309,0.297],[0.3,0.34],[0.202,0.458],[0.159,0.485],[0.123,0.48],[0.099,0.459],[0.081,0.403],[0.081,0.349],[0.107,0.328],[0.136,0.326],[0.156,0.289],[0.156,0.247],[0.138,0.208],[0.123,0.184],[0.094,0.157],[0.094,0.147],[0.065,0.145],[-0.096,0.029],[-0.782,0.026],[-1.064,-0.007],[-1.079,-0.019],[-1.088,-0.043]],"scaleRefs":["std.ar15.hammer_pin_x","std.ar15.trigger_pin_x","std.ar15.hammer_pin_y","std.ar15.trigger_pin_y"],"inputs":{"std.ar15.hammer_pin_x":2.771,"std.ar15.hammer_pin_y":-0.375,"std.ar15.trigger_pin_x":1.928,"std.ar15.trigger_pin_y":-0.689},"tolerance":0.004,"photo":"references/geissele-ssa-e 3329bf5cf26e (the SSA-E assembled and cocked, square to its right side on white (the older engraving, U.S. PAT. 7600338); the maker's artwork as Selway Armory's page serves it, 1310 x 1500)","method":"luminance < 140, 1 boxes excluded, 2 polygons excluded, pieces ≥ 2000 px, closing 9 px ×2, the piece at [300, 740], holes filled; frame from the reviewed holes trigger_pin, hammer_pin (552.7 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.004 in with the extremes kept: 80 points (IoU 0.992 with the full outline); the pins' centres picked on a 4.5x crop as the middles of their ends (dark discs on a dark ground, each 79 to 83 px across: 0.149 in at this scale for the .154 in they are, 3% thin, which is the edge of a dark disc on dark); the trigger spring's wire, silver, is bridged by the closing where it crosses the tail's top and the body's lower front; checks: −x_min 1.097 ± 0.004; −y_min 1.403 ± 0.005; x_max 0.788 ± 0.004; x_max in y [-0.42, -0.33] 0.500 ± 0.003; −y_min in x [-1.0, -0.3] 0.287 ± 0.003 (tools/trace.py)","via":"harvest","note":"The trigger alone: its tail, the sear ahead of the pin, the block at its front and the curved bow. Dark on dark, and so picked by hand: its top from the disconnector's rear to the sear (a straight line under the trigger spring's coil), the block's top under the hammer, and the foot of the sear where the hammer's hook sits on it. The body's own boss round the pin is under the spring's coil and isn't in the outline."},"hammer":{"plane":"xy","origin":"the trigger pin's axis (the trigger frame's origin): the hammer is where a receiver holds it, cocked, its own pin .8430 ahead and .3140 up","offset":{},"points":[[-0.316,1.042],[-0.31,1.022],[-0.226,0.958],[-0.176,0.9],[-0.134,0.822],[-0.106,0.713],[-0.11,0.592],[-0.154,0.429],[-0.156,0.391],[-0.168,0.376],[-0.248,0.329],[-0.243,0.313],[-0.225,0.294],[-0.195,0.276],[-0.051,0.233],[0.045,0.219],[0.079,0.225],[0.096,0.247],[0.105,0.327],[0.078,0.351],[0.056,0.352],[0.052,0.424],[0.063,0.475],[0.086,0.517],[0.121,0.55],[0.163,0.565],[0.219,0.563],[0.22,0.528],[0.232,0.509],[0.273,0.491],[0.304,0.49],[0.312,0.481],[0.398,0.368],[0.54,0.158],[0.542,0.137],[0.584,0.105],[0.595,0.105],[0.651,0.067],[0.657,0.051],[0.78,0.041],[0.789,0.026],[0.804,0.02],[0.804,-0.009],[0.816,-0.023],[0.87,-0.019],[0.896,-0.01],[0.982,0.041],[1.03,0.084],[1.077,0.16],[1.095,0.213],[1.104,0.269],[1.094,0.35],[1.071,0.406],[1.027,0.469],[0.981,0.512],[0.937,0.539],[0.609,0.7],[0.27,0.859],[0.229,0.903],[0.218,0.964],[0.196,0.987],[-0.152,1.143],[-0.228,1.17],[-0.25,1.166],[-0.265,1.153]],"scaleRefs":["std.ar15.hammer_pin_x","std.ar15.trigger_pin_x","std.ar15.hammer_pin_y","std.ar15.trigger_pin_y"],"inputs":{"std.ar15.hammer_pin_x":2.771,"std.ar15.hammer_pin_y":-0.375,"std.ar15.trigger_pin_x":1.928,"std.ar15.trigger_pin_y":-0.689},"tolerance":0.004,"photo":"references/geissele-ssa-e 3329bf5cf26e (the SSA-E assembled and cocked, square to its right side on white (the older engraving); the maker's artwork as Selway Armory's page serves it, 1310 x 1500)","method":"luminance < 140, 1 polygons excluded, pieces ≥ 2000 px, closing 9 px ×2, the piece at [700, 250], holes filled; frame from the reviewed holes trigger_pin, hammer_pin (552.7 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.004 in with the extremes kept: 65 points (IoU 0.989 with the full outline); checks: width 1.419 ± 0.007; height 1.192 ± 0.007; x_max 1.104 ± 0.004; y_max 1.170 ± 0.004 (tools/trace.py)","via":"harvest","note":"The hammer alone, cocked: its head, the two hooks under it and the round end about its pin. Its spring is on it: the coils are inside the outline, and the bent end of the upper leg, hooked under the hammer's shelf, is in it (0.04 by 0.06 in). Picked by hand: where the lower hook sits on the trigger's sear, and its underside from the spring's lower leg to its tail's end, over the trigger's block."},"disconnector":{"plane":"xy","origin":"the trigger pin's axis (the trigger frame's origin)","offset":{},"points":[[-0.757,0.027],[-0.756,0.026],[-0.187,0.029],[-0.189,0.135],[-0.297,0.135],[-0.314,0.154],[-0.324,0.206],[-0.315,0.23],[-0.244,0.286],[-0.261,0.311],[-0.264,0.337],[-0.283,0.374],[-0.311,0.393],[-0.383,0.388],[-0.525,0.208],[-0.572,0.188],[-0.721,0.142],[-0.744,0.13],[-0.754,0.111]],"scaleRefs":["std.ar15.hammer_pin_x","std.ar15.trigger_pin_x","std.ar15.hammer_pin_y","std.ar15.trigger_pin_y"],"inputs":{"std.ar15.hammer_pin_x":2.771,"std.ar15.hammer_pin_y":-0.375,"std.ar15.trigger_pin_x":1.928,"std.ar15.trigger_pin_y":-0.689},"tolerance":0.004,"photo":"references/geissele-ssa-e 3329bf5cf26e (the SSA-E assembled and cocked, square to its right side on white (the older engraving); the maker's artwork as Selway Armory's page serves it, 1310 x 1500)","method":"luminance < 140, inside [236, 440, 552, 655], 1 polygons excluded, pieces ≥ 500 px, closing ×2, the piece at [420, 560], holes filled; frame from the reviewed holes trigger_pin, hammer_pin (552.7 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.004 in with the extremes kept: 19 points (IoU 0.974 with the full outline) (tools/trace.py)","via":"harvest","note":"What shows of the disconnector above the trigger's tail: its rear hook and its top edge forward to where the trigger spring's coil hides it (cut there, 0.19 in behind the pin it turns on). Its underside is taken as the tail's top (the window its spring shows through is filled)."}},"gaps":[{"what":"The bosses' span across the trigger and across the hammer (drawn at a mil-spec trigger's)","need":"A view square to the group's top or front, or the maker's sheet for the SSA-E (on the maker's site, which isn't read)"},{"what":"The weight: three sellers state 2.2, 2.5 and 3.2 oz and none says what was weighed","need":"The maker's figure, or a reviewer's on a scale with what was on it"},{"what":"The outlines' scale: the two pins' ends as far apart as a receiver holds them. Two things read 3% small at it and say the outline may be that much small: the pins' own ends (0.149 in for .154, dark discs on a dark ground) and the bow's tip (1.40 in below the pin for the Army's own trigger's 1.45 ± .02, if an M4 bow is the Army's). A third reading, the pins lying beside the trigger in BCM's parts view (33.0 px across for .154 where the trigger is 409.8 px long), has it 1.4% small, give or take 2.4%. The pocket and the slot take it either way","need":"The group in a lower, square to the side (the lower's own pins give the scale), or a published length of any piece"},{"what":"A photo of it installed, square to the side with both pins in frame: the rest angle is the group's as pictured out of a rifle","need":"A seller's or reviewer's side view of a lower with the SSA-E in it"},{"what":"The trigger's top under the disconnector and the spring's coil, the bevels on the block, the bow's rounding across","need":"The trigger alone square to its side and to its front (BCM's parts view is from above)"}]},"geissele-super-42-h1":{"id":"geissele-super-42-h1","name":"Super 42 Braided Wire Buffer Spring and Buffer Combo, H1","manufacturer":"Geissele Automatics","sku":"05-495","url":"https://geissele.com/super-42-braided-wire-buffer-spring-and-buffer-combo-h1.html","category":"buffer","description":"A recoil spring and the buffer made for it, sold as a set: the spring is wound of three strands of wire twisted together, and it takes the place of both the buffer and the spring. The maker's sheet: \"Its unique spring design uses three independent strands of wire, just like the German MG42 Machine Gun.\" This set's buffer is the H1: one tungsten weight and two steel inside it. The maker's sheet: \"The Geissele Super 42 Spring and Buffer Combination ships in the standard H1 configuration.\" \"The H1 and Braided Wire Spring works well in 18” SPRs, 16” rifles with mid-length or carbine gas systems and some 14.5” rifles.\" Mile High Shooting, which sells it: \"The Super 42 is for use with Carbine-length buffer tubes and is not compatible with rifle-length or A5 buffer tubes/receiver extensions.\" \"The Super 42 spring and Geissele buffer are designed to work together as a set; the spring will not fit over a standard buffer.\"","weight":"geissele-super-42-h1.weight","occupies":["buffer_spring"],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"bore":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the buffer's axis at its head's front face, +x rearward."}},"interfaces":{"bore":{"type":"ar15.extension_bore","role":"buffer","anchor":"bore","params":{},"flips":false}},"materials":{"body":{"label":"Buffer body","finish":"anodized_matte","recolorable":false,"color":"geissele-buffer-anodize","note":"Aluminium (Midwest Gun Works: \"Material: Steel,Aluminum\", \"Finish / Color: Unfinished\"; Alexander's: \"Color: Silver\"). A pale gold in Midwest Gun Works' photo of the set, a pale silver-green in Primary Arms', plain silver in two owners'."},"bumper":{"label":"Bumper","finish":"polymer","recolorable":false,"color":"geissele-buffer-bumper","note":"A pale grey in Midwest Gun Works' photo of the set (bd3cd61e3456)."},"pin":{"label":"Pin","finish":"steel","recolorable":false,"color":"steel-phosphate-dark","note":"The pin through the body and the bumper: a dark dot in a hole in the sellers' side photos."},"spring":{"label":"Spring","finish":"steel","recolorable":false,"color":"geissele-spring-wire","note":"Steel music wire by the maker's patent; a dark bronze brown in Midwest Gun Works' photo (bd3cd61e3456)."}},"components":{},"geometry":{"model":"geissele-super-42-h1.glb","components":{},"approximations":["The buffer is a standard carbine buffer's shape (the Army's drawings and the reference CAD set, as BCM's buffers are drawn) with its shoulder turned to the 0.762 in an owner measured, which is the one thing Geissele says it changed: \"We had to make the shoulder slightly smaller because of the braided wire design being 'thicker' than a single piece.\" Its head is drawn with the standard's three flats, as Primary Arms' photo of its face has it.","The spring is three round strands twisted about each other once in 0.475 in and coiled, 26 coils with the end coils closed, at the length it is held to in a carbine extension with the bolt forward. The wire's size, the twist and the coil's outside diameter are the maker's patent's example, which no marking page on file ties to the product; an owner's measurements of the spring differ from them, and what the spring has to fit decided between the two (the ledger's notes). The coil's inside is drawn on the buffer's shoulder, 0.003 in over the patent's figure.","Not drawn: the one tungsten weight and two steel inside the buffer; the maker's name and \"H 1\" on its face; the spring as it is out of a rifle, four inches longer."],"ledger":["geissele-super-42-h1.length","geissele-super-42-h1.od","geissele-super-42-h1.shoulder_d","geissele-super-42-h1.spring_od","geissele-super-42-h1.strand_d","geissele-super-42-h1.twist_pitch","geissele-super-42-h1.coils","geissele-super-42-h1.installed_length"]},"profiles":{},"gaps":[{"what":"The maker's own figures","need":"Geissele's page or drawing for the set, saved by the user from their browser: the site isn't read (D59), and every size here is an owner's or the patent's"}]},"geissele-super-42-h2":{"id":"geissele-super-42-h2","name":"Super 42 Braided Wire Buffer Spring and Buffer Combo, H2","manufacturer":"Geissele Automatics","sku":"05-495-H2","url":"https://www.milehighshooting.com/geissele-super-42-braided-wire-buffer-spring-and-buffer-combo-h2/","category":"buffer","description":"A recoil spring and the buffer made for it, sold as a set: the spring is wound of three strands of wire twisted together, and it takes the place of both the buffer and the spring. The maker's sheet: \"Its unique spring design uses three independent strands of wire, just like the German MG42 Machine Gun.\" This set's buffer is the H2: two tungsten weights and one steel inside it. The maker's sheet: \"Most 14.5” rifles would benefit from the H2 Buffer, which the military issues in their M4A1 rifles.\" Mile High Shooting, which sells it: \"The Super 42 is for use with Carbine-length buffer tubes and is not compatible with rifle-length or A5 buffer tubes/receiver extensions.\" \"The Super 42 spring and Geissele buffer are designed to work together as a set; the spring will not fit over a standard buffer.\"","weight":"geissele-super-42-h2.weight","occupies":["buffer_spring"],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"bore":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the buffer's axis at its head's front face, +x rearward."}},"interfaces":{"bore":{"type":"ar15.extension_bore","role":"buffer","anchor":"bore","params":{},"flips":false}},"materials":{"body":{"label":"Buffer body","finish":"anodized_matte","recolorable":false,"color":"geissele-buffer-anodize","note":"Aluminium (Midwest Gun Works: \"Material: Steel,Aluminum\", \"Finish / Color: Unfinished\"; Alexander's: \"Color: Silver\"). A pale gold in Midwest Gun Works' photo of the set, a pale silver-green in Primary Arms', plain silver in two owners'."},"bumper":{"label":"Bumper","finish":"polymer","recolorable":false,"color":"geissele-buffer-bumper","note":"A pale grey in Midwest Gun Works' photo of the set (bd3cd61e3456)."},"pin":{"label":"Pin","finish":"steel","recolorable":false,"color":"steel-phosphate-dark","note":"The pin through the body and the bumper: a dark dot in a hole in the sellers' side photos."},"spring":{"label":"Spring","finish":"steel","recolorable":false,"color":"geissele-spring-wire","note":"Steel music wire by the maker's patent; a dark bronze brown in Midwest Gun Works' photo (bd3cd61e3456)."}},"components":{},"geometry":{"model":"geissele-super-42-h2.glb","components":{},"approximations":["The buffer is a standard carbine buffer's shape (the Army's drawings and the reference CAD set, as BCM's buffers are drawn) with its shoulder turned to the 0.762 in an owner measured, which is the one thing Geissele says it changed: \"We had to make the shoulder slightly smaller because of the braided wire design being 'thicker' than a single piece.\" Its head is drawn with the standard's three flats, as Primary Arms' photo of its face has it.","The spring is three round strands twisted about each other once in 0.475 in and coiled, 26 coils with the end coils closed, at the length it is held to in a carbine extension with the bolt forward. The wire's size, the twist and the coil's outside diameter are the maker's patent's example, which no marking page on file ties to the product; an owner's measurements of the spring differ from them, and what the spring has to fit decided between the two (the ledger's notes). The coil's inside is drawn on the buffer's shoulder, 0.003 in over the patent's figure.","Not drawn: the two tungsten weights and one steel inside the buffer; the maker's name and \"H 2\" on its face; the spring as it is out of a rifle, four inches longer."],"ledger":["geissele-super-42-h2.length","geissele-super-42-h2.od","geissele-super-42-h1.shoulder_d","geissele-super-42-h1.spring_od","geissele-super-42-h1.strand_d","geissele-super-42-h1.twist_pitch","geissele-super-42-h1.coils","geissele-super-42-h1.installed_length"]},"profiles":{},"gaps":[{"what":"The maker's own figures","need":"Geissele's page or drawing for the set, saved by the user from their browser: the site isn't read (D59), and every size here is an owner's or the patent's"}]},"geissele-super-42-h3":{"id":"geissele-super-42-h3","name":"Super 42 Braided Wire Buffer Spring and Buffer Combo, H3","manufacturer":"Geissele Automatics","sku":"05-495-H3","url":"https://www.milehighshooting.com/geissele-super-42-braided-wire-buffer-spring-and-buffer-combo-h3/","category":"buffer","description":"A recoil spring and the buffer made for it, sold as a set: the spring is wound of three strands of wire twisted together, and it takes the place of both the buffer and the spring. The maker's sheet: \"Its unique spring design uses three independent strands of wire, just like the German MG42 Machine Gun.\" This set's buffer is the H3: three tungsten weights inside it. The maker's sheet: \"Weapons with barrels shorter than 14.5” will need some testing with H2 or H3 buffer combinations to prove out which is most reliable.\" Mile High Shooting, which sells it: \"The Super 42 is for use with Carbine-length buffer tubes and is not compatible with rifle-length or A5 buffer tubes/receiver extensions.\" \"The Super 42 spring and Geissele buffer are designed to work together as a set; the spring will not fit over a standard buffer.\"","weight":"geissele-super-42-h3.weight","occupies":["buffer_spring"],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"bore":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the buffer's axis at its head's front face, +x rearward."}},"interfaces":{"bore":{"type":"ar15.extension_bore","role":"buffer","anchor":"bore","params":{},"flips":false}},"materials":{"body":{"label":"Buffer body","finish":"anodized_matte","recolorable":false,"color":"geissele-buffer-anodize","note":"Aluminium (Midwest Gun Works: \"Material: Steel,Aluminum\", \"Finish / Color: Unfinished\"; Alexander's: \"Color: Silver\"). A pale gold in Midwest Gun Works' photo of the set, a pale silver-green in Primary Arms', plain silver in two owners'."},"bumper":{"label":"Bumper","finish":"polymer","recolorable":false,"color":"geissele-buffer-bumper","note":"A pale grey in Midwest Gun Works' photo of the set (bd3cd61e3456)."},"pin":{"label":"Pin","finish":"steel","recolorable":false,"color":"steel-phosphate-dark","note":"The pin through the body and the bumper: a dark dot in a hole in the sellers' side photos."},"spring":{"label":"Spring","finish":"steel","recolorable":false,"color":"geissele-spring-wire","note":"Steel music wire by the maker's patent; a dark bronze brown in Midwest Gun Works' photo (bd3cd61e3456)."}},"components":{},"geometry":{"model":"geissele-super-42-h3.glb","components":{},"approximations":["The buffer is a standard carbine buffer's shape (the Army's drawings and the reference CAD set, as BCM's buffers are drawn) with its shoulder turned to the 0.762 in an owner measured, which is the one thing Geissele says it changed: \"We had to make the shoulder slightly smaller because of the braided wire design being 'thicker' than a single piece.\" Its head is drawn with the standard's three flats, as Primary Arms' photo of its face has it.","The spring is three round strands twisted about each other once in 0.475 in and coiled, 26 coils with the end coils closed, at the length it is held to in a carbine extension with the bolt forward. The wire's size, the twist and the coil's outside diameter are the maker's patent's example, which no marking page on file ties to the product; an owner's measurements of the spring differ from them, and what the spring has to fit decided between the two (the ledger's notes). The coil's inside is drawn on the buffer's shoulder, 0.003 in over the patent's figure.","Not drawn: the three tungsten weights inside the buffer; the maker's name and \"H 3\" on its face; the spring as it is out of a rifle, four inches longer."],"ledger":["geissele-super-42-h3.length","geissele-super-42-h3.od","geissele-super-42-h1.shoulder_d","geissele-super-42-h1.spring_od","geissele-super-42-h1.strand_d","geissele-super-42-h1.twist_pitch","geissele-super-42-h1.coils","geissele-super-42-h1.installed_length"]},"profiles":{},"gaps":[{"what":"The maker's own figures","need":"Geissele's page or drawing for the set, saved by the user from their browser: the site isn't read (D59), and every size here is an owner's or the patent's"}]},"geissele-super-duty-stripped-lower":{"id":"geissele-super-duty-stripped-lower","name":"Super Duty AR-15 Lower Receiver - Stripped Lower","manufacturer":"Geissele Automatics","sku":"05-2994-B","url":"https://www.primaryarms.com/geissele-automatics-super-duty-stripped-ar-15-lower-stripped-lower","category":"lower","description":"Geissele's forged stripped lower, marked GEISSELE AUTOMATICS with the Super Duty keystone, SD-556 and CAL 5.56MM on the well's left wall: \"a mil-spec foundation ready to be the heart of your next AR-15 build\", \"Precision machined from 7075-T6 aluminum to mil-spec dimensions\", \"Type III hardcoat anodized finish\", \".250-inch takedown holes and Safe/Fire indicators\" (Primary Arms, 05-2994-B; Geissele's own site refuses the reader). No trigger guard: a separate one pins into its ears; its well's mouth is a square lip, not a flare; its bolt catch's bosses are the standard's.","weight":"geissele-super-duty-stripped-lower.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"pins":{"origin":[0,0,0],"note":"The rifle frame origin."},"buffer_tube_mount":{"origin":[0,"{.buffer_axis_above_pin}",0],"x":[-1,0,0]},"magwell":{"origin":["{.magazine_seat_x}","{std.ar15.mag_catch_slot_bottom_y} + {std.ar15.mag_catch_slot_h}",0],"note":"Where a seated magazine hangs: x where its spine's rear face sits in the well (magazine_seat_x), y at the catch's upper face, the top of the slot the catch comes through (the Army drawing's). A magazine's own anchor is the upper edge of its catch notch, so each hangs by its own. The drawing's well and catch slot, as the catalog's other mil-spec lowers have it: no photo of a magazine seated in this lower is on file."},"grip_lug":{"origin":[0,"{.grip_seat_y}",0],"note":"The grip mount's datum: the face either side of the lug that a grip's flat top bears on, at the takedown pin's x: the Army drawing's, 1.318 below the deck (the rectified right photo's own reading is 0.005 above it)."},"trigger_guard":{"origin":["{.trigger_guard_front_x}","{.trigger_guard_front_y}",0],"x":["{.trigger_guard_front_x} - {.trigger_guard_rear_x}","{.trigger_guard_front_y} - {.trigger_guard_rear_y}",0],"note":"At the front ear hole, with the guard's x axis through the rear ear hole: a guard pins into both. The Army drawing's holes; the photos show both ears with their holes and no guard forged between them."},"fcg":{"origin":["{.trigger_pin_x}","{.trigger_pin_y}",0],"note":"Trigger pin axis."},"lpk":{"origin":[0,0,"-{std.ar15.lower_body_width} / 2"],"note":"The body's left face (the TDP's width), level with the takedown pin: the controls' heads seat on it."},"selector":{"origin":["{std.ar15.selector_x}","{std.ar15.selector_y}",0],"note":"The selector's hole (the Army's drawing 8448608), on its axis at the receiver's mid-plane: a selector chosen on its own turns here (D86), its levers' inner faces on the body's two sides."}},"interfaces":{"receiver_pins":{"type":"ar15.upper_lower","role":"lower","anchor":"pins","params":{"pin_spacing":"={std.ar15.pin_spacing}"},"flips":false},"buffer_tube_mount":{"type":"ar15.buffer_tube_mount","role":"receiver","anchor":"buffer_tube_mount","params":{},"flips":false},"magwell":{"type":"ar15.magwell","role":"receiver","anchor":"magwell","params":{"family":"5.56"},"flips":false,"note":"A standard AR-15 magazine well: 'Designated for 5.56 caliber builds', 'Caliber Marking 5.56 NATO', 'Platform AR-15' (Primary Arms); marked CAL 5.56MM."},"grip_lug":{"type":"ar15.grip_lug","role":"receiver","anchor":"grip_lug","params":{},"flips":false},"trigger_guard":{"type":"ar15.trigger_guard","role":"receiver","anchor":"trigger_guard","params":{},"flips":false},"fcg":{"type":"ar15.fcg","role":"receiver","anchor":"fcg","params":{"pin_diameter":"small-pin"},"flips":false,"note":"'Trigger Pin Diameter MIL-SPEC .154' (Primary Arms)."},"lpk":{"type":"ar15.lpk","role":"receiver","anchor":"lpk","params":{},"flips":false},"selector":{"type":"ar15.selector","role":"receiver","anchor":"selector","params":{},"flips":false}},"materials":{"receiver":{"label":"Receiver","finish":"anodized","recolorable":true,"color":"placeholder-black","sheen":"matte","options":{"black":{"label":"Black","finish":"anodized","color":"placeholder-black","sheen":"matte","sku":"05-2994-B","source":"https://www.primaryarms.com/geissele-automatics-super-duty-stripped-ar-15-lower-stripped-lower"},"ddc":{"label":"Desert Dirt","finish":"anodized","color":"geissele-ddc-lower","sku":"05-2994-S","source":"https://www.primaryarms.com/geissele-automatics-super-duty-stripped-lower-ddc-stripped-lower"}},"default":"black","note":"Primary Arms of 05-2994-B: 'Type III hardcoat anodized finish', 'Finish Hardcoat Anodized', 'Color Black'; of 05-2994-S, titled 'Geissele Automatics Super Duty AR-15 Lower Receiver - Stripped Lower - Desert Dirt': 'SKU: 05-2994-S', 'Color Flat Dark Earth', 'Finish Hardcoat Anodized'. One piece, one colour: every pin hole, the thread and the marks are the receiver's own anodize in both colourways' photos (the marks are engraved, not filled). The black is a sealed black anodize and isn't fitted (the app's anodized black is its look). The Desert Dirt is fitted on this lower's own two side photos (geissele-ddc-lower, make color-match): a khaki tan, lighter and less red than the same studio's MK16 rail in DDC (geissele-ddc); Primary Arms says of DDC that its shades 'can vary drastically even between products from the same batch and are not intended to color match'. Also sold, not offered: OD green, seen only as Geissele's receiver set (Aegis Cerakote's picture of 05-1171ODG; Primary Arms' address for an OD green lower answered 404 on 2026-10-28), with no page read selling the lower alone in it; and blemished lowers ('BLEM' listings in a discovery's search, in 40MM Green, Luna Black and others), which are seconds, not colourways."}},"components":{"receiver":{"label":"Receiver","material":"receiver"}},"geometry":{"model":"geissele-super-duty-stripped-lower.glb","components":{},"approximations":["Its two photos are Primary Arms' black receiver from about two feet (the right from 23 in, its lens's foot at X 2.45, Y -0.50; the left from 24 in, at 1.55, -0.92): each was laid square onto its near face by a fit to the Army drawing's six holes on it before anything was read, and what the far wall adds to the silhouette taken off. The right one, by a homography, has every hole within 0.0034 in of the drawing and its ring's top on the drawing's; the left one, by an affine fit (a homography on its six holes put the ring 0.23 in low), within 0.031 in, and x read on it near the bolt catch is taken 0.03 back by the drawing's slot in the same rows.","The grip's mount is the standard's, not read from this lower's photos: the face a grip bears on 1.318 below the deck and the lug at the drawing's .375 across, its rear face under the takedown pin, its sloped face 1.228 from the pin at 60 degrees, its flat .93 below the seat (the Army's drawing 8448608); the walls with the trigger guard's ears 0.659 across (the reference CAD model) and the ears .438 +.008 apart (the drawing); the rear underside the reference model's, an arc on the centre plane and a half-round across the body. The rectified right photo has the seat 0.005 above the drawing's and the lug's rear face 0.015 behind it.","The traced outline at the TDP's body width (0.880), its magazine well's walls at 1.098 from each side's own rear edge forward (3.50 on the right, the left's curved edge from 2.945 down to 3.485), and the buffer tower's ring at 1.392 about the buffer axis, its top and its rear face the drawing's (the right photo's ring top is the drawing's within 0.002).","The tower's bore through the ring and on along the trough between the walls' sweep, cut at the mil-spec receiver extension's OD (1.148): the thread it really has is larger by its depth, which isn't on file. The walls rise to the ring's front face along the Army drawing's arc (.750 R) and no higher. Its deck is the Army drawing's plane (.250 -.003 above the pins: std.ar15.deck_y), not the outline's own top edge (0.255 on the right photo).","The inside a forged mil-spec lower has, from the Army's drawing 8448608 (D46): the fire-control pocket, the rear lug's slot, the safety detent's boss, the trigger slot and the magazine well with its spine slot, open from the deck to the mouth: the seller says 'any mil-spec lower parts kit and components drop right in without modification'; nothing of its own inside is measured. The pivot lug as its two ears, the slot between them the drawing's .500 across.","The holes its photos show open, at the drawing's sizes and places: the takedown and pivot pins' (Primary Arms: '.250\" takedown holes'), the selector's, the hammer's and trigger's (the page: '.154' pins), the trigger guard's roll pin hole through both ears and its front hole in the right ear from its spotface, the takedown hole's spotface on the right.","On the left, read on its own photo: the magazine catch's slot opening into the well, the catch hole through to the button's pocket, the band down the well's wall and the round boss the slot runs through (the reference model's, where the photo has them), the bolt catch's two bosses (their edges from the photo, read from the drawing's slot between them, out to the TDP's face) and its slot and plunger hole.","On the right, read on its own photo: the magazine catch's fence, its flat face from 2.955 to 3.545 and from -0.215 to -0.975, out to the well walls' face and run on into the wall and up under the roll; the button's pocket and the counterbore from the reference model; the roll along the top of the well's wall from 2.955 to its flat front end at 6.25, its lower edge -0.21 below the pin line, its rear end rounded over 0.17; and the small blind hole in it 1.05 in behind the pivot pin (0.045 across; its depth assumed). How far the roll stands out isn't read (no view looks along the receiver): the Workhorse's 0.80 from the centre, where this one's ends and lower edge are within a few hundredths of that lower's.","Drawn at heights no view gives (assumed, each a ledger entry that says so): the rib that runs down from the roll beside the fence to a point (its edges and its point read on the right photo, its crest 0.04 off the wall's face) and the two oblong pads either side of the selector on the left (their stadium outlines read on the left photo, 0.03 off the face): raised by their light in the square views and in the three-quarter ones.","Not drawn: the marks (GEISSELE AUTOMATICS, the Super Duty keystone, SD-556, CAL 5.56MM, the serial, NORTH WALES, PA., FIRE and SAFE), the grip screw's hole in the lug, the buffer retainer's hole, the bolt catch pin's hole (in the rear boss's rear face along the receiver, as Primary Arms' view from behind the left side shows it; roll pin or threaded isn't seen), and the large round hole in the rear face under the ring with the small one beside it (three views from behind show them, none square to that face). The ring's thread: bored at the mil-spec tube's outside, as every lower on file is (app/tests/buffer-system.test.ts holds a tube's thread crests standing in that wall); the thread's figures are on file (std.receiver_extension.thread_*), but where its helix stands against a tube's is how far the tube is turned in, which nothing fixes.","Edges broken at 0.02 in (the drawing's \"break corners .02 R\")."],"ledger":["std.ar15.lower_body_width","std.ar15.magwell_outside_width","std.ar15.buffer_tower_od","std.receiver_extension.milspec_od","std.ar15.grip_seat_below_deck","std.ar15.grip_lug_width","std.ar15.trigger_guard_ears_width","std.ar15.trigger_guard_ear_gap","std.ar15.mag_catch_fence_out","std.ar15.bolt_catch_boss_out","std.ar15.pin_spacing","geissele-super-duty-stripped-lower.buffer_axis_above_pin","geissele-super-duty-stripped-lower.rear_behind_pin","geissele-super-duty-stripped-lower.tower_front_x","geissele-super-duty-stripped-lower.magwell_front_x","geissele-super-duty-stripped-lower.magwell_wall_rear_x","geissele-super-duty-stripped-lower.magwell_wall_rear_x_left","geissele-super-duty-stripped-lower.magwell_wall_upper_rear_x_left","geissele-super-duty-stripped-lower.fence_rear_x","geissele-super-duty-stripped-lower.fence_front_x","geissele-super-duty-stripped-lower.fence_top_y","geissele-super-duty-stripped-lower.fence_bottom_y","geissele-super-duty-stripped-lower.well_roll_bottom_y","geissele-super-duty-stripped-lower.well_roll_rear_x","geissele-super-duty-stripped-lower.well_roll_front_x","geissele-super-duty-stripped-lower.well_roll_crest_out","geissele-super-duty-stripped-lower.bolt_catch_boss_rear_x","geissele-super-duty-stripped-lower.bolt_catch_boss_front_x","geissele-super-duty-stripped-lower.trigger_guard_front_x","geissele-super-duty-stripped-lower.trigger_guard_rear_x","geissele-super-duty-stripped-lower.trigger_pin_x","geissele-super-duty-stripped-lower.trigger_pin_y","geissele-super-duty-stripped-lower.magazine_seat_x","geissele-super-duty-stripped-lower.grip_seat_y","geissele-super-duty-stripped-lower.width"]},"profiles":{"side":{"plane":"xy","origin":"the takedown pin centre (the rifle frame origin), +x toward the muzzle","offset":{},"points":[[-1.17,0.758],[-1.13,-0.232],[-1.08,-0.493],[-0.798,-0.53],[-0.528,-0.65],[-0.36,-0.822],[-0.248,-1.055],[-0.06,-1.078],[-0.06,-1.362],[-0.038,-1.39],[0.972,-1.975],[1.163,-1.99],[1.188,-2.345],[1.632,-2.35],[1.745,-2.273],[1.712,-2.17],[1.48,-2.028],[1.375,-1.752],[1.375,-1.592],[1.42,-1.433],[1.475,-1.333],[1.637,-1.185],[1.877,-1.09],[2.857,-1.085],[3.013,-1.115],[3.152,-1.19],[3.265,-1.292],[3.37,-1.453],[3.425,-1.723],[3.4,-1.877],[3.17,-2.142],[3.19,-2.302],[3.282,-2.35],[6.178,-1.82],[6.195,-1.723],[6.09,-1.562],[6.095,-0.567],[6.14,-0.442],[6.245,-0.303],[6.5,-0.147],[6.545,-0.067],[6.555,0.038],[6.51,0.137],[6.418,0.205],[6.008,0.24],[-0.038,0.265],[-0.268,0.35],[-0.495,0.613],[-0.6,0.903],[-0.585,1.188],[-0.635,1.568],[-0.968,1.575],[-1.095,1.522],[-1.125,1.413],[-1.165,1.127]],"scaleRefs":["std.ar15.pin_spacing"],"inputs":{"std.ar15.pin_spacing":6.375},"tolerance":0.02,"photo":"references/geissele-super-duty-stripped-lower efc0b44358f7 (right side: Primary Arms' photo ddfadb3e24e2 (05-2994-B_05) laid square onto the right face by the drawing's holes, the far wall's share taken off)","method":"alpha > 0.5, largest piece, holes filled; frame from the reviewed holes takedown, pivot (200.0 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.02 in with the extremes kept: 55 points (IoU 0.992 with the full outline); the picture's pins are where the rectification put the drawing's (its homography has each of the six holes' near rims within 0.0034 in of the drawing); checks: −x_min 1.170 ± 0.008; x_max 6.555 ± 0.011; y_max 1.575 ± 0.008; −y_min 2.350 ± 0.008; top (tooth tops: the edge's max over 0.05 in windows) along x [0.6, 5.8] 0.255 ± 0.015 in vs std.ar15.deck_y 0.2485 ± 0.0015 (confirmed): agrees; −x_min in y [-0.9, 0.0] 1.140 ± 0.008 (tools/trace.py)","via":"harvest","note":"The right face's outline, its holes filled; no trigger guard (the ears are the lowest points behind the well). The tower ring is round, not a prism: its top and rear read as its silhouette does from this camera and are the drawing's in the model."}},"gaps":[{"what":"its weight: no page read publishes one (Primary Arms, Blackstone, Aegis Cerakote); geissele.com refuses the reader","need":"a seller's or reviewer's page that weighs the stripped receiver; the figure on file is its model's metal"},{"what":"how far the roll on the well's right wall stands out (the Workhorse's 0.80 from the centre is drawn), and how far the two oblong pads by the selector and the rib beside the fence stand off their faces (assumed: 0.03 and 0.04)","need":"a view along the receiver from ahead or behind, or a close oblique with a known edge beside them"},{"what":"OD green: seen only as Geissele's receiver set (05-1171ODG), with no page read selling the lower alone in it","need":"a seller's page for an OD green Super Duty lower with its number and a photo"}]},"geissele-super-duty-stripped-upper":{"id":"geissele-super-duty-stripped-upper","name":"Super Duty Stripped Upper Receiver","manufacturer":"Geissele Automatics","url":"https://charliescustomclones.com/geissele-super-duty-forged-ar15-upper-lower-receiver-matched-set-ddc/","category":"upper","description":"Geissele's Super Duty upper, sold stripped with its Super Duty lower in the Super Duty Receiver Set: \"This matched set pairs a Super Duty stripped upper receiver with a Super Duty stripped lower receiver, both forged from 7075-T6 aluminum\"; \"The upper receiver is stripped — no forward assist, dust cover, or barrel nut included.\" (Charlie's Custom Clones). \"Forged 7075-T6 aluminum Hardcoat anodized black Mil-Spec dimensions\" (Primary Arms, 05-1171B); \"Upper Specs: Material: 7075-T6 Color: Black Finish: Type-3 Hardcoat Anodize Compatibility: Mil-Spec Markings: Milled T-Marks\" (Aegis Cerakote).","weight":"geissele-super-duty-stripped-upper.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"pins":{"origin":[0,0,0]},"front_face":{"origin":["{.front_face_x}","{.bore_axis_above_pin}",0],"note":"The end of the barrel-nut thread on the bore axis, +x toward the muzzle: a barrel extension's flange seats here, and a handguard is placed from here."},"rear_face":{"origin":["{.receiver_rear_x}","{.bore_axis_above_pin}",0],"note":"The rear face on the bore axis, +x toward the muzzle: the bolt carrier's channel opens here."},"handle_channel":{"origin":["{.handle_seat_x}","{.bore_axis_above_pin} + {.charging_handle_above_bore}",0],"note":"The charging handle's seat on its channel's axis, +x toward the muzzle: the front wall of the open notch under the rail's rear end, which the handle's shoulder stops against, at the notch's mid-height."},"top_rail":{"origin":["{.rail_slot0_x}","{.rail_top_above_pin}",0],"note":"The rail's top at its rearmost slot's centre, +x toward the muzzle (picatinny: index = slot number)."}},"interfaces":{"receiver_pins":{"type":"ar15.upper_lower","role":"upper","anchor":"pins","params":{"pin_spacing":"={std.ar15.pin_spacing}"},"flips":false},"barrel_extension":{"type":"ar15.barrel_extension","role":"receiver","anchor":"front_face","params":{},"flips":false},"handguard_mount":{"type":"ar15.handguard_mount","role":"receiver","anchor":"front_face","params":{"nut":"standard"},"flips":false,"note":"No page names its barrel nut or a handguard for it (Charlie's: \"no forward assist, dust cover, or barrel nut included\"): the barrel nut's thread is taken as the Army drawing's (1 1/4-18) on Primary Arms' \"Mil-Spec dimensions\" and \"It is compatible with Mil-Spec AR-15 parts and accessories\" (05-1171B), and its photo's nose reads the drawing's diameter within its ±."},"carrier_channel":{"type":"ar15.carrier_channel","role":"receiver","anchor":"rear_face","params":{},"flips":false},"charging_handle_channel":{"type":"ar15.charging_handle_channel","role":"receiver","anchor":"handle_channel","params":{},"flips":false},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}","seam":"={.rail_front_x} - {.rail_slot0_x}","seam_parts":"the receiver's rail and the handguard's","seam_behind":"receiver","seam_ahead":"handguard"},"flips":false,"note":"Its own rail, its slots counted on Aegis Cerakote's side photo of the set; a handguard's rail ahead of it is the handguard's own. Its front end is the body's front shoulder, where the barrel-nut thread begins (the photo), which is where a handguard's rail takes over."}},"materials":{"receiver":{"label":"Receiver","finish":"anodized","recolorable":true,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized","color":"placeholder-black","sku":"05-1171B","source":"https://www.primaryarms.com/geissele-automatics-super-duty-stripped-ar15-receiver-set-black"},"ddc":{"label":"Desert Dirt Color","finish":"anodized","color":"geissele-ddc-receiver-set","sku":"05-1171S","source":"https://www.primaryarms.com/geissele-automatics-super-duty-stripped-ar-15-receiver-set-ddc"}},"default":"black","note":"Sold in the set's colours, each the set's number (the upper has none of its own): black, \"Hardcoat anodized black\" (Primary Arms, 05-1171B), \"Finish: Type-3 Hardcoat Anodize\" (Aegis Cerakote); Desert Dirt Color, \"Hardcoat anodized Desert Dirt Color (DDC)\" (Primary Arms, 05-1171S), \"Geissele's proprietary Desert Dirt Color (DDC) — the same anodizing process used on their contract rifles\", \"shade can vary slightly between production runs\" (Charlie's Custom Clones): the DDC is geissele-ddc-receiver-set, fitted to Primary Arms' photos of this set (05-1171S_04 and _03: a copper brown, #9e7650 on the upper's left flat, where the same studio's DDC MK16 rail, geissele-ddc, reads a grey taupe, #8b776d): the set is sold matched, \"Buying a matched set guarantees consistent color across both halves of your rifle\" (Charlie's Custom Clones), so its lower is this colour too. One piece in both colourways: the thread, the deflector, the hinge lugs and the forward assist's housing are the receiver's own anodize in every photo of each. An OD green set is pictured on Aegis Cerakote's black set's page under a file named for 05-1171ODG; no page on file sells it, and it isn't offered."}},"components":{},"geometry":{"components":{"receiver":"geissele-super-duty-stripped-upper.receiver.glb"},"approximations":["Drawn stripped, as it is sold: the forward assist's bore empty and the ejection port without its door (\"The upper receiver is stripped — no forward assist, dust cover, or barrel nut included\").","Its side outline is Aegis Cerakote's photo of the black set from the right (3292 px, 341 px to the inch), above the lower's deck, in the frame of the lower's two pin holes (the upper's own are inside them), across the mil-spec forging's section (Primary Arms: \"Mil-Spec dimensions\"): the Army drawing's forged 1.18 round body, the rail's lower faces under its slots' floors the standard's (MIL-STD-1913's), the height of its dovetail's foot, its neck, the flat sides and the walls from the reference CAD set (a third-party model of a mil-spec forging). No end or top view of this receiver is on file, so its own section isn't sourced. The neck's wall leans from its width under the dovetail's foot out to the side's face (the model's .010 step there isn't drawn: a third of a pixel at the page's size).","Its lugs are the reference model's (hidden inside the lower in every photo on file): the takedown lug a flat-bottomed block, the pivot lug rounded about its pin, each at the drawing's width, their edges broken at 0.012 in where the model has larger breaks.","On the right, the forward assist's housing is a cylinder about the Army drawing's axis (20° in plan, placed by the reference model) from where the photo shows its rear face until it has sunk into the round body, solid back to the wall, its .509 bore open, its radius the photo's (its bore reads the drawing's .509 in the same photo); the brass deflector is the photo's outline, rising to the reference model's crest and sloping to the port; the port is the drawing's (3.125 long); the door's two hinge lugs are where the photo shows them, about the reference model's pin axis. How far each stands out is the forging's, not measured on this receiver. What the photo shows nearer its lens than the mid-plane is brought back by its depth, with the lens placed by the lower's two pin holes (about 28 in away, above the rail).","The left side is the mil-spec forging's: the cam pin's pad is the reference model's flat face, and the charging handle latch's slot is the Army drawing's (Section D-D: .156 of wall ahead of the notch, .195 long) between the reference model's heights, a pocket down to the drawing's .045 of wall over the channel. Aegis Cerakote's left photo of the set, read through the lens its pin holes place, has the pad's top and front end and the slot's ends and length where these figures put them (within 0.02), and the pad's rear end 0.09 further back, which isn't drawn: which line of a lit round that edge is isn't settled at the photo's size (the ledger keeps both, a conflict).","Behind its rail's head the rail is the standard's tongue (lib.rail_tongue), its rearmost point where the set's left photo has the rail's end (its right photo reads 0.04 further back, where the tongue would stand in a charging handle's T: the ledger keeps both). The charging handle's channel is the standard's (lib.handle_channel), and so is the notch the handle's block lies in at least (lib.handle_notch); its front wall is the drawing's, scaled.","The barrel nut's thread is a right-hand helix (lib.thread_x) at the drawing's pitch and diameters, its crests where a mil-spec nut's tap has its roots (bcm_gi_barrel_nut.py), its height running out over a pitch at the shoulder and half a pitch at the face (the face's chamfer: not sourced, the helper's run-out); the gas tube's hole, the charging handle's channel and the flange round the rear end are the drawing's and the reference model's, and the lower rear corner is cut to the arc a lower's two rear walls rise along (lib.upper_rear_corner).","Not drawn: the port door's seat and its detent, the M4 feed ramps the assembled sibling's page states, \"proprietary cuts inside the upper\" a buyer speaks of, the openings in the underside (it is closed under the bore), the milled T-marks, the square forge mark and the G on the DDC set's photo; edges broken at 0.015 in."],"ledger":["geissele-super-duty-stripped-upper.receiver_rear_x","geissele-super-duty-stripped-upper.front_face_x","geissele-super-duty-stripped-upper.underside_y","geissele-super-duty-stripped-upper.rail_top_above_pin","geissele-super-duty-stripped-upper.bore_axis_above_pin"]},"profiles":{"side":{"plane":"xy","origin":"the takedown pin centre (the rifle frame origin), +x toward the muzzle","offset":{},"points":[[-0.621,2.098],[-0.621,1.913],[-0.598,1.899],[-0.082,1.895],[0.004,1.799],[0.004,1.65],[-0.053,1.593],[-0.621,1.594],[-0.621,0.249],[6.609,0.248],[6.619,0.292],[6.675,0.292],[6.713,0.257],[6.742,0.289],[6.763,0.251],[6.792,0.289],[6.819,0.251],[6.848,0.289],[6.874,0.251],[6.904,0.289],[6.93,0.254],[6.965,0.289],[6.986,0.254],[7.036,0.307],[7.036,1.446],[7.006,1.479],[6.985,1.465],[6.965,1.497],[6.932,1.468],[6.909,1.497],[6.883,1.468],[6.853,1.497],[6.833,1.456],[6.798,1.497],[6.777,1.456],[6.742,1.498],[6.715,1.462],[6.704,1.474],[6.68,1.46],[6.614,1.464],[6.618,2.083],[6.564,2.105],[6.139,2.103],[6.124,1.986],[5.96,1.977],[5.947,2.084],[5.91,2.103],[5.746,2.101],[5.738,1.997],[5.672,1.984],[5.552,1.987],[5.545,2.085],[5.526,2.101],[5.353,2.101],[5.357,2.027],[5.341,1.99],[5.153,1.984],[5.168,1.97],[5.149,1.977],[5.146,2.08],[5.127,2.102],[4.963,2.102],[4.955,1.992],[4.875,1.982],[4.746,1.991],[4.744,2.084],[4.725,2.106],[4.57,2.1],[4.557,2.087],[4.546,1.974],[4.546,1.986],[4.344,1.989],[4.347,2.1],[4.177,2.101],[4.155,2.085],[4.155,2.003],[4.133,1.966],[4.067,1.97],[4.138,1.972],[4.138,1.986],[3.974,1.984],[3.958,1.997],[3.964,2.02],[3.949,2.015],[3.954,2.101],[3.784,2.101],[3.753,2.082],[3.745,1.984],[3.66,1.981],[3.571,1.995],[3.561,2.102],[3.388,2.099],[3.351,2.083],[3.341,1.976],[3.194,1.979],[3.178,1.996],[3.171,2.1],[2.992,2.1],[2.949,2.081],[2.946,1.996],[2.924,1.965],[2.795,1.968],[2.778,2.1],[2.555,2.089],[2.534,1.972],[2.518,1.982],[2.528,1.987],[2.405,1.984],[2.379,2.101],[2.215,2.101],[2.146,2.083],[2.137,1.98],[2.1,1.967],[2.02,1.971],[2.064,1.983],[2.005,1.995],[1.989,2.102],[1.748,2.088],[1.735,1.987],[1.693,1.979],[1.621,1.984],[1.603,2.092],[1.59,2.103],[1.534,2.091],[1.42,2.1],[1.342,2.084],[1.326,1.971],[1.226,1.968],[1.203,2.1],[-0.202,2.109]],"features":{"forward_assist_rim":[[[-0.778,1.12],[-0.594,1.12],[-0.595,0.486],[-0.78,0.487]]],"forward_assist_bore":[[[-0.735,1.067],[-0.647,1.067],[-0.648,0.539],[-0.736,0.539]]],"deflector":[[[2.032,1.596],[2.12,1.69],[2.765,1.688],[2.868,1.624],[2.926,1.448],[2.931,0.89],[2.72,0.826],[2.031,0.828],[2.01,0.921]]],"deflector_crest":[[[2.208,1.522],[2.296,1.522],[2.295,1.068],[2.207,1.068]]],"port":[[[2.911,1.345],[6.07,1.339],[6.069,0.802],[2.91,0.808]]],"hinge_rear":[[[2.743,0.847],[2.902,0.846],[2.901,0.368],[2.742,0.369]]],"hinge_front":[[[6.107,0.738],[6.289,0.737],[6.288,0.391],[6.106,0.392]]]},"scaleRefs":["std.ar15.pin_spacing"],"inputs":{"geissele-super-duty-stripped-upper.front_face_x":7.036,"geissele-super-duty-stripped-upper.receiver_rear_x":-0.621,"geissele-super-duty-stripped-upper.underside_y":0.2485,"std.ar15.pin_spacing":6.375},"tolerance":0.01,"photo":"references/geissele-super-duty-stripped-upper 95a4d20d054e (Aegis Cerakote's 05-1171B set photo 02: this stripped upper on its lower, from the right, 3292 x 1988)","method":"luminance < 200, largest piece, holes filled; frame from the reviewed holes takedown, pivot (341.0 px/in, rms 0.000 in over 2 points); origin at the photo's frame; clipped to x min {.receiver_rear_x} = -0.621, x max {.front_face_x} = 7.036, y min {.underside_y} = 0.2485; Douglas-Peucker at 0.01 in with the extremes kept: 130 points (IoU 0.998 with the full outline); checks: top (tooth tops: the edge's max over 0.4 in windows) along x [1.0, 6.0] 2.101 ± 0.009; x_min in y [1.95, 2.2] -0.649 ± 0.004; x_max in y [0.6, 1.2] 7.080 ± 0.007; x_max in y [1.6, 2.2] 6.624 ± 0.006; y_max in x [6.7, 7.0] 1.498 ± 0.005; y_min in x [6.7, 7.0] 0.251 ± 0.004; y_max in x [-0.5, -0.1] in y [1.2, 1.75] 1.593 ± 0.005; y_min in x [-0.45, -0.1] in y [1.75, 2.05] 1.895 ± 0.005; features through the same placement (forward_assist_rim: the forward assist housing's rear end from the right, the dark bore inside it: from its bottom tangent (v 780) to that mirrored about the bore's centre (v 672); its top tangent is lost in the shadowed fillet above it (v 527 to 560); forward_assist_bore: the bore's rear opening, the dark ellipse; deflector: the brass deflector's outline: its steep rear face from u 1338, the crease at u 1405 to 1435, its long slope to the port's rear end; deflector_crest: the crease between the deflector's rear face and its slope; port: the ejection port's opening, the dark obround; hinge_rear: the port door's rear hinge lug, under the deflector's front; hinge_front: the port door's front hinge lug) (tools/trace.py)","via":"harvest","note":"Its outer silhouette above the deck, cut at the standard's rear and front faces (the silhouette's own rear end is the forward assist's rim and the lower's tower behind it); the forward assist, the deflector, the port and the door's hinge lugs as the photo shows them, inside it."}},"gaps":[{"what":"A number of its own and a price","need":"A page that sells the bare upper: it is sold in the Super Duty Receiver Set (05-1171B, 05-1171S) with its lower, which is where its offers belong (a kit), and the assembled 05-3201B is another product"},{"what":"Its weight as published","need":"A page or a review that weighs it: none states one; it is weighed by its metal"},{"what":"Its width, its left side's own figures, and how far its forward assist housing and deflector stand out","need":"An end or a top view with a known size in frame, and the left photo measured: the mil-spec forging's figures stand in"},{"what":"Its own lugs","need":"A photo of the upper off its lower from the side: every photo on file has it on the lower, and the reference model's lugs stand in"},{"what":"A forward assist and a port door for it","need":"Those parts in the catalog: it is sold without them, and drawn without them"}]},"geissele-super-precision-micro-193":{"id":"geissele-super-precision-micro-193","name":"Super Precision T1 Mount - 1.93\" Height","manufacturer":"Geissele","sku":"05-543B","url":"https://www.primaryarms.com/geissele-automatics-super-precision-aimpoint-t2-mount-1.93in-black","category":"optic_mount","description":"Geissele's mount for the Aimpoint Micro footprint at 1.93 in: \"1.93″ Height to optic centerline\" (Rooftop Defense), \"Mount Height 1.93 in.\", \"1.93\\\" central height for gas masks\", \"Clears range finders, lasers, and IR devices\", \"Covers just 1.37\\\" of rail space\" (Primary Arms). Geissele, as Rooftop Defense quotes it: \"The Super Precision T1 Series was developed specifically to work with the Aimpoint T1 and similarly mounted red dot optics\", \"Utilizing Geissele's update of the classic nut and bolt method, this mount will attach your red dot to your weapon with 1,400 pounds of clamping force, and features 3 shear lugs for maximum rigidity and return to zero.\" Sold in black (05-543B) and Desert Dirt Color (05-543S).","weight":"geissele-super-precision-micro-193.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":[0,0,0],"note":"Mount frame: origin on the rail's top under the middle of the base, +x forward. The cross bolt lies across the base there (its axis at the rail's top in Primary Arms' square side view: in the slot the build names), and a fixed lug hangs into the slot either side of it."},"deck":{"origin":["{.deck_x}","{.deck_above_rail}",0],"note":"On the floor between the plate's two fences, over the middle of the four screw holes: where a Micro dot's base is put (D101). Primary Arms' square side view has the plate's middle over the base's."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":"={.mount_length} / 2","clamp_front":"={.mount_length} / 2","cross_rear":"={.lug_spacing}","cross_front":"={.lug_spacing}"},"flips":false,"note":"The base's 1.37 in about its middle, where the cross bolt is (Primary Arms: \"Covers just 1.37\\\" of rail space\"). \"3 shear lugs\" (Geissele, as Rooftop Defense quotes it): the bolt in the slot the build names and a fixed lug in the slot either side, a pitch out. The maker's tightening, as nbg.eu quotes it of its lower 1/3 sibling (05-469): \"The clamping nut is tightened with a ½″ wrench to a quarter turn past hand tight; if a torque wrench is used, do not exceed 8.1 N·m (72 in-lb / 6 ft-lb).\" No page on file says where along a rail it goes."},"deck":{"type":"optic_footprint","role":"deck","anchor":"deck","params":{"pattern":"aimpoint_micro"},"flips":false,"note":"Primary Arms: \"Mount Compatibility Aimpoint Micro\" and \"For Aimpoint T2 / T1 and compatible optics\"; Geissele (Rooftop Defense): \"developed specifically to work with the Aimpoint T1 and similarly mounted red dot optics\". (data/interfaces.yaml, optic_footprint)"}},"materials":{"body":{"label":"Mount","finish":"anodized","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized","color":"placeholder-black","sku":"05-543B","source":"https://www.primaryarms.com/geissele-automatics-super-precision-aimpoint-t2-mount-1.93in-black"},"ddc":{"label":"Desert Dirt Color","finish":"anodized","color":"geissele-ddc-t1-mount","sku":"05-543S","source":"https://www.primaryarms.com/geissele-automatics-super-precision-aimpoint-t2-mount-1.93in-desert-dirt"}},"default":"black","note":"The plate, the neck, the base and its lugs: one piece. Primary Arms: \"Type 3 hardcoat anodized\" (05-543B; 05-543S's spec row says \"Color Flat Dark Earth\"); Rooftop Defense: \"Finish: Type 3 Hardcoat Anodize\", \"Color Black, FDE\". Drawn under anodized, as Geissele's other hardcoated parts are. The Desert Dirt is geissele-ddc-t1-mount, fitted to Primary Arms' level photos of its two siblings' DDC left sides (data/colors/geissele.yaml); this mount's own DDC photos (Primary Arms' c8fa7e8075ca and ce7972771223, Rooftop Defense's) show its right side and from above, and agree with it as far as the side's light lets them. Piece map (black: f98596d6dd96, 036d638fcddd; DDC: c8fa7e8075ca, ce7972771223, f18f5ba7abc4, 284b2ff50787): the body is the colourway's; the jaw block, the collar and the nut are black on both; the bolt's round head is a dark grey metal on both in Primary Arms' and Rooftop's pictures."},"hardware":{"label":"Jaw block, collar and nut","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The jaw block on the left that the nut draws against the rail, the round collar and the hex nut (a slot across its end): a dark grey metal, the same on the black mount and the Desert Dirt one (Primary Arms' f98596d6dd96, ce7972771223). No page says what they are or how they are finished: drawn as blackened steel."},"button":{"label":"Bolt head","finish":"steel","recolorable":false,"color":"stainless-natural","note":"The cross bolt's round head in the base's right face, marked G: a grey metal, darker in this height's photos (c8fa7e8075ca) than in its siblings'. Bare metal, not fitted: drawn as a matte natural steel, as on its siblings."}},"components":{"body":{"label":"Mount","material":"body"},"hardware":{"label":"Jaw block","material":"hardware"},"button":{"label":"Bolt head","material":"button"}},"geometry":{"model":"geissele-super-precision-micro-193.glb","components":{},"approximations":["No drawing of this height is on file. Its lengths and heights are read on Primary Arms' square side view of the DDC one at the base's published 1.37 in; its widths on Rooftop Defense's view from below; how deep its clamp reaches under the rail on Rooftop's view from the front and above. The deck is the sellers' 1.93 in less the T-2's own axis over its base; the photos read it 0.05 in lower, within the two ±.","Read on a sibling's photo, each the only straight view of it on file (the ledger names the photo): the base's end outline (the right face's chamfers above and below), the jaw block's hook's foot and the lugs' depth, on the lower 1/3's square end view; the holes in the plate's top (the four screw holes and the two larger ones), on the absolute's view from above. This height's own views show the same features where they show them.","The plate's top is drawn flat at the deck's height, the floor a dot's base sits on. The two fences along its sides and the square key in the middle aren't drawn: every Micro dot on file is drawn with its housing down to its base, wider than the space between the fences, and would stand in them. The plate is drawn 0.075 in thinner than it is.","The neck is straight-sided along the rail; across it, a circle through the three widths the view from the front gives (at the plate, along its straight stretch, at the base): the photo has it straight with fillets at its two ends. The base is the side view's outline (upright ends, sloped shoulders up to the neck) across the end outline; the relief round the bolt's head and the hollows above and below it on the right face aren't drawn.","The rail's channel on the right is the rail's own head (MIL-STD-1913's) from its top down to the lower gauge line, plain walls below; the jaw block on the left is a block hipped at its top, its inner face the rail's head. The two fixed lugs are blocks hanging into the slots a pitch either side of the bolt (the view from below reads that pitch). The bolt's shank isn't drawn; its round head stands a hundredth out of the right face (assumed). The nut's slot is 0.05 in wide and 0.04 deep (assumed).","The four screw holes are through the plate, counterbored from below (their depth assumed); the two larger holes in the floor are drawn 0.15 in deep (assumed). The dot's four screws aren't drawn. Every machined edge is broken by 0.008 in (assumed); the engraving and the \"193\" stamped on a lug aren't drawn.","As drawn it is 1.36 cubic inches of 7075 and 0.21 of steel: 90 g, against Geissele's 2.5 oz (70.9 g) as two sellers carry it (KYGUNCO: 2.6 oz); the body alone as 7075 is 63 g. The jaw block is drawn as steel and may be aluminium (no page says)."],"ledger":["geissele-super-precision-micro-193.optical_axis_above_rail","geissele-super-precision-micro-193.deck_above_rail","geissele-super-precision-micro-193.mount_length","geissele-super-precision-micro-193.plate_length","geissele-super-precision-micro-193.clamp_below_rail","geissele-super-precision-micro-193.width_over_nut","geissele-super-precision-micro-193.lug_spacing"]},"profiles":{},"gaps":[{"what":"Geissele's own drawing, figures and instruction sheet","need":"geissele.com refuses the reader: a drawing of this height would replace the photos' readings and the sibling's photos used for its end outline and its top"},{"what":"Which dot the 1.93 in is for","need":"A page that names it: Primary Arms titles the mount for the T2, Geissele's text names the T1"},{"what":"Where on the rail it goes","need":"A maker's sentence (receiver only, not across the rail's seam): none on any page read"}]},"geissele-super-precision-micro-absolute":{"id":"geissele-super-precision-micro-absolute","name":"Super Precision T1 Mount - Absolute Co-Witness","manufacturer":"Geissele","sku":"05-401B","url":"https://www.primaryarms.com/geissele-super-precision-aimpoint-t1-compatible-optic-mount-absolute-cowitness-black-05-401b","category":"optic_mount","description":"Geissele's mount for the Aimpoint Micro footprint at absolute co-witness: \"Mount Height 1.41 in.\", \"Covers just 1.37\\\" of rail space\" (Primary Arms). Geissele, as its sellers quote it: \"The Super Precision T1 Series was developed specifically to work with the Aimpoint T1 and similarly mounted red dot optics. These mounts are precision machined from a single piece of 7075-T6 high strength aluminum\" and \"Utilizing Geissele's update of the classic nut and bolt method, this mount will attach your red dot to your weapon with 1,400 pounds of clamping force, and features 3 shear lugs for maximum rigidity and return to zero.\" Sold in black (05-401B) and Desert Dirt Color (05-401S).","weight":"geissele-super-precision-micro-absolute.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":[0,0,0],"note":"Mount frame: origin on the rail's top under the middle of the base, +x forward. The cross bolt lies across the base there (its axis 0.014 in over the rail's top by the drawing: in the slot the build names), and a fixed lug hangs into the slot either side of it."},"deck":{"origin":["{.deck_x}","{.deck_above_rail}",0],"note":"On the floor between the plate's two fences, over the middle of the four screw holes: where a Micro dot's base is put (D101). The drawing has the plate's middle over the base's."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":"={.mount_length} / 2","clamp_front":"={.mount_length} / 2","cross_rear":"={.lug_spacing}","cross_front":"={.lug_spacing}"},"flips":false,"note":"The base's 1.37 in about its middle, where the cross bolt is (Primary Arms: \"Covers just 1.37\\\" of rail space\"). \"3 shear lugs\" (Geissele, as Rooftop Defense quotes it): the bolt in the slot the build names and a fixed lug in the slot either side, a pitch out. The maker's tightening, as nbg.eu quotes it of the lower 1/3 (05-469): \"The clamping nut is tightened with a ½″ wrench to a quarter turn past hand tight; if a torque wrench is used, do not exceed 8.1 N·m (72 in-lb / 6 ft-lb).\" No page on file says where along a rail it goes."},"deck":{"type":"optic_footprint","role":"deck","anchor":"deck","params":{"pattern":"aimpoint_micro"},"flips":false,"note":"Primary Arms: \"Mount Compatibility Aimpoint Micro\" and \"For Aimpoint T2 / T1 and compatible optics\"; Geissele (Rooftop Defense): \"developed specifically to work with the Aimpoint T1 and similarly mounted red dot optics\". (data/interfaces.yaml, optic_footprint)"}},"materials":{"body":{"label":"Mount","finish":"anodized","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized","color":"placeholder-black","sku":"05-401B","source":"https://www.primaryarms.com/geissele-super-precision-aimpoint-t1-compatible-optic-mount-absolute-cowitness-black-05-401b"},"ddc":{"label":"Desert Dirt Color","finish":"anodized","color":"geissele-ddc-t1-mount","sku":"05-401S","source":"https://www.primaryarms.com/geissele-super-precision-aimpoint-t1-compatible-optic-mount-absolute-cowitness-desert-dirt-null"}},"default":"black","note":"The plate, the neck, the base and its lugs: one piece. Primary Arms: \"Type 3 hardcoat anodized Black finish\" (05-401B) and \"Type 3 hardcoat anodized Desert Dirt finish\" (05-401S, whose spec row says \"Color Flat Dark Earth\"); Sportsman's Warehouse: \"Finish: Type-3 Hardcoat Anodize\". Drawn under anodized, as Geissele's other hardcoated parts are. The Desert Dirt is geissele-ddc-t1-mount, fitted to Primary Arms' level photos of the DDC mounts' left sides (data/colors/geissele.yaml); Geissele's DDC MK16 rail's colour, from the same studio, drew it greyer than its photos. This mount's DDC photos: Primary Arms' 0d1926ea2276, d5da4f341161, 519bd106cdb1, ba687bf5d135; Charlie's 69833f58365b. Primary Arms says of the colour that its shades \"can vary drastically even between products from the same batch\". Piece map (black: fee93b489c46, 5dbff517b303, d25985149572, ed0da8852dab; DDC: 0d1926ea2276, ba687bf5d135): the body is the colourway's; the jaw block, the collar and the nut are dark on both; the bolt's round head is a pale steel on both. nbg.eu lists a \"Clear\" beside Black and DDC in its colour choice, and its text says \"Available in Black and DDC\": no photo of a clear one is on file, and it isn't offered."},"hardware":{"label":"Jaw block, collar and nut","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The jaw block on the left that the nut draws against the rail, the round collar and the hex nut (a slot across its end): a dark grey metal, the same on the black mount and the Desert Dirt one (Primary Arms' 0d1926ea2276, ba687bf5d135). No page says what they are or how they are finished: drawn as blackened steel."},"button":{"label":"Bolt head","finish":"steel","recolorable":false,"color":"stainless-natural","note":"The cross bolt's round head in the base's right face, marked G: a pale grey metal on both colours (#c8c3b7 and #cbc5b7 on Primary Arms' black mount, fee93b489c46, its two halves either side of the G). Bare metal, not fitted: drawn as a matte natural steel."}},"components":{"body":{"label":"Mount","material":"body"},"hardware":{"label":"Jaw block","material":"hardware"},"button":{"label":"Bolt head","material":"button"}},"geometry":{"model":"geissele-super-precision-micro-absolute.glb","components":{},"approximations":["Built from the dimensioned drawing in Charlie's Custom Clones' gallery (a straight side view and a straight end view of the mount with a Micro dot on it: 1.41, 1.37, 1.78), each size read at the drawing's own scale and checked on Primary Arms' and Sportsman's Warehouse's photos; the holes in the plate from Sportsman's view from above. The ledger gives each its ±, mostly a hundredth or two.","The plate's top is drawn flat at the deck's height, the floor a dot's base sits on. The two fences along its sides, 0.08 in above the floor by the drawing (which has the plate's top 0.867 in over the rail), and the square key in the middle of the floor aren't drawn: every Micro dot on file is drawn with its housing down to its base, wider than the 0.58 in between the fences, and would stand in them. So is the arc cut in the right fence. The plate is drawn 0.08 in thinner than it is.","The plate is wider on the right than on the left (0.61 and 0.48 in out from the rail's middle), as the drawing's end view and the view from above both have it; its long lower edges are chamfered as the drawing has them and its lower ends cut back as much (the drawing draws them round).","The neck is straight-sided along the rail and concave across it: a circle through the three widths the end view gives (at the plate, at its narrowest, at the base). The base is the side view's outline (upright ends, sloped shoulders) across the end view's (the right jaw's face chamfered above and below, the left face above the rail where the jaw block bears); the relief round the bolt's head and the hollows above and below it on the right face aren't drawn.","The rail's channel on the right is the rail's own head (MIL-STD-1913's) from its top down to the lower gauge line, plain walls below; the jaw block on the left is a block hipped at its top, its inner face the rail's head, as long as Primary Arms' view from below has it. The two fixed lugs are blocks hanging into the slots a pitch either side of the bolt (the photos from below read a little less: the ledger says why a pitch). The bolt's shank isn't drawn; its round head stands a hundredth out of the right face (assumed). The nut's slot is 0.05 in wide and 0.04 deep (assumed); its flats and length, and the collar, are the drawing's.","The four screw holes are through the plate, counterbored from below (their depth assumed); the two larger holes in the floor are drawn 0.15 in deep (assumed). The dot's four screws aren't drawn. Every machined edge is broken by 0.008 in (assumed); the engraving isn't drawn.","As drawn it is 1.11 cubic inches of 7075 and 0.20 of steel: 77.5 g, against Geissele's 2 oz (57 g) as Sportsman's Warehouse lists it, and bestpatron.eu's \"approx. 79 g\". The body alone as 7075 is 51 g. The jaw block is drawn as steel and may be aluminium (no page says); as aluminium the whole would be 64 g."],"ledger":["geissele-super-precision-micro-absolute.optical_axis_above_rail","geissele-super-precision-micro-absolute.deck_above_rail","geissele-super-precision-micro-absolute.mount_length","geissele-super-precision-micro-absolute.plate_length","geissele-super-precision-micro-absolute.clamp_below_rail","geissele-super-precision-micro-absolute.width_over_nut","geissele-super-precision-micro-absolute.lug_spacing"]},"profiles":{},"gaps":[{"what":"Geissele's own drawing, figures and instruction sheet","need":"geissele.com refuses the reader: its spec page and instructions (the dot's screws and their torque) would replace the sellers' quotations and the drawing's readings"},{"what":"Which dot the 1.41 in is for","need":"A page that names it: Primary Arms titles the mount for the T2, Geissele's text names the T1; the deck's height is the 1.41 less the T-2's own axis over its base, and a T-1 is taken to stand as high"},{"what":"The weight as drawn against Geissele's","need":"The mount weighed, or a second page of Geissele's 2 oz: as drawn it is 36% over it, and a European seller's 79 g agrees with the drawing"},{"what":"Where on the rail it goes","need":"A maker's sentence (receiver only, not across the rail's seam): none on any page read"}]},"geissele-super-precision-micro-lower-13":{"id":"geissele-super-precision-micro-lower-13","name":"Super Precision T1 Mount - Lower 1/3 Co-Witness","manufacturer":"Geissele","sku":"05-469B","url":"https://www.primaryarms.com/geissele-super-precision-aimpoint-t1-compatible-optic-mount-lower-1-3-cowitness","category":"optic_mount","description":"Geissele's mount for the Aimpoint Micro footprint at lower 1/3 co-witness: \"Lower 1/3rd cowitness with standard sights\", \"Covers just 1.37\\\" of rail space\" (Primary Arms). Its height is given two ways by its sellers: \"Mount Height 1.59 in.\" (Primary Arms) and \"1.70″ Lower 1/3 Cowitness Height to optic centerline\" (Rooftop Defense); its own photographs put a T-2's axis lower than either (the ledger). Geissele, as Rooftop Defense quotes it: \"The Super Precision T1 Series was developed specifically to work with the Aimpoint T1 and similarly mounted red dot optics\", \"Utilizing Geissele's update of the classic nut and bolt method, this mount will attach your red dot to your weapon with 1,400 pounds of clamping force, and features 3 shear lugs for maximum rigidity and return to zero.\" Sold in black (05-469B) and Desert Dirt Color (05-469S).","weight":"geissele-super-precision-micro-lower-13.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":[0,0,0],"note":"Mount frame: origin on the rail's top under the middle of the base, +x forward. The cross bolt lies across the base there (its axis at the rail's top in Primary Arms' side view: in the slot the build names), and a fixed lug hangs into the slot either side of it."},"deck":{"origin":["{.deck_x}","{.deck_above_rail}",0],"note":"On the floor between the plate's two fences, over the middle of the four screw holes: where a Micro dot's base is put (D101). Primary Arms' side view has the plate's middle within a hundredth of the base's."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":"={.mount_length} / 2","clamp_front":"={.mount_length} / 2","cross_rear":"={.lug_spacing}","cross_front":"={.lug_spacing}"},"flips":false,"note":"The base's 1.37 in about its middle, where the cross bolt is (Primary Arms: \"Covers just 1.37\\\" of rail space\"). \"3 shear lugs\" (Geissele, as Rooftop Defense quotes it): the bolt in the slot the build names and a fixed lug in the slot either side, a pitch out. The maker's tightening, as nbg.eu quotes it of this mount (05-469): \"The clamping nut is tightened with a ½″ wrench to a quarter turn past hand tight; if a torque wrench is used, do not exceed 8.1 N·m (72 in-lb / 6 ft-lb).\" No page on file says where along a rail it goes."},"deck":{"type":"optic_footprint","role":"deck","anchor":"deck","params":{"pattern":"aimpoint_micro"},"flips":false,"note":"Primary Arms: \"Mount Compatibility Aimpoint Micro\" and \"For Aimpoint T2 / T1 and compatible optics\"; nbg.eu: \"Geissele Super Precision mount for the Aimpoint T1 and other optics on the Aimpoint Micro footprint\"; Geissele (Rooftop Defense): \"developed specifically to work with the Aimpoint T1 and similarly mounted red dot optics\". (data/interfaces.yaml, optic_footprint)"}},"materials":{"body":{"label":"Mount","finish":"anodized","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized","color":"placeholder-black","sku":"05-469B","source":"https://www.primaryarms.com/geissele-super-precision-aimpoint-t1-compatible-optic-mount-lower-1-3-cowitness"},"ddc":{"label":"Desert Dirt Color","finish":"anodized","color":"geissele-ddc-t1-mount","sku":"05-469S","source":"https://www.primaryarms.com/geissele-super-precision-aimpoint-t1-compatible-optic-mount-lower-1-3-cowitness-desert-dirt"}},"default":"black","note":"The plate, the neck, the base and its lugs: one piece. Primary Arms: \"Type 3 hardcoat anodized Black finish\"; Rooftop Defense: \"Finish: Type 3 Hardcoat Anodize\"; nbg.eu: \"Type 3 hardcoat anodise, Black or DDC\". Drawn under anodized, as Geissele's other hardcoated parts are. The Desert Dirt is geissele-ddc-t1-mount, fitted to Primary Arms' level photos of the DDC mounts' left sides (data/colors/geissele.yaml); Geissele's DDC MK16 rail's colour, from the same studio, drew it greyer than its photos. This mount's DDC photos: Primary Arms' 42be4f94bd99, 09199eedefb4, ccb852a64b8d, aa42d318e782, da3ad1df27ce; Rooftop Defense's. Piece map (black: 066cdfa6fbe5, 0642ffe614c6, e2ee9e6aacfd, db434af2fca3; DDC: 42be4f94bd99, 09199eedefb4, da3ad1df27ce, 0d9d31213881): the body is the colourway's; the jaw block, the collar and the nut are black on both; the bolt's round head a dark grey metal on the black one and a pale one on the DDC one. nbg.eu lists a \"Clear\" in its colour choice beside Black and DDC, and its text says \"Black or DDC\": no photo of a clear one is on file, and it isn't offered."},"hardware":{"label":"Jaw block, collar and nut","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The jaw block on the left that the nut draws against the rail, the round collar and the hex nut (a slot across its end): a dark grey metal, the same on the black mount and the Desert Dirt one (Primary Arms' 0642ffe614c6, 09199eedefb4). No page says what they are or how they are finished: drawn as blackened steel."},"button":{"label":"Bolt head","finish":"steel","recolorable":false,"color":"stainless-natural","note":"The cross bolt's round head in the base's right face, marked G: a grey metal in this height's photos (Primary Arms' black 066cdfa6fbe5 has it darker than its siblings' photos do; its DDC ccb852a64b8d pale). Bare metal, not fitted: drawn as a matte natural steel, as on its siblings."}},"components":{"body":{"label":"Mount","material":"body"},"hardware":{"label":"Jaw block","material":"hardware"},"button":{"label":"Bolt head","material":"button"}},"geometry":{"model":"geissele-super-precision-micro-lower-13.glb","components":{},"approximations":["No drawing of this height is on file. Every size is read on its own photos (Primary Arms' straight right side and straight end view, its views from above and below), at the scale of the base's published 1.37 in in the side view and the scales that sets for the others; the ledger gives each its ±, mostly two hundredths. Read the same way, the absolute's photo gives its drawing's height to 0.002 in.","The deck is drawn where this height's photos put it, 0.884 in over the rail: a T-2 on it has its axis at 1.473 in. Its sellers say 1.59 and 1.70 in: both stay in the ledger, against a reading of this mount's own photo that agrees with neither (the ledger's optical_axis_above_rail says how).","The plate's top is drawn flat at the deck's height, the floor a dot's base sits on. The two fences along its sides (0.08 in above the floor in the end view) and the square key in the middle aren't drawn: every Micro dot on file is drawn with its housing down to its base, wider than the 0.55 in between the fences, and would stand in them. So is the arc cut in the right fence. The plate is drawn 0.08 in thinner than it is.","The plate is wider on the right than on the left (0.60 and 0.48 in out from the rail's middle), as the end view and the view from above have it; its long lower edges are chamfered as the end view has them and its lower ends cut back as much. The neck is straight-sided along the rail and concave across it: a circle through the three widths the end view gives (it flares more toward the plate and the base than the absolute's); the end view has its narrowest 0.04 in right of the rail's middle, and it is drawn on the middle. The base is the side view's outline across the end view's; the relief round the bolt's head and the hollows above and below it on the right face aren't drawn.","The rail's channel on the right is the rail's own head (MIL-STD-1913's) from its top down to the lower gauge line, plain walls below; the jaw block on the left is a block hipped at its top, its inner face the rail's head, as long as the view from below has it. The two fixed lugs are blocks hanging into the slots a pitch either side of the bolt (the view from below reads the stamped one a pitch out; the other is too dark to read). The bolt's shank isn't drawn; its round head stands a hundredth out of the right face (assumed). The nut's slot is 0.05 in wide and 0.04 deep (assumed).","The four screw holes are through the plate, counterbored from below (their depth assumed); the two larger holes in the floor are drawn 0.15 in deep (assumed). The dot's four screws aren't drawn. Every machined edge is broken by 0.008 in (assumed); the engraving and the \"1/3\" stamped on a lug aren't drawn.","As drawn it is 1.00 cubic inches of 7075 and 0.18 of steel: 69.5 g, against Geissele's 2.1 oz (59.5 g) as three sellers carry it; the body alone as 7075 is 46 g. The jaw block is drawn as steel and may be aluminium (no page says). Its siblings are drawn as much over their list figures (the absolute 77.5 g for 2 oz, the 1.93 90 g for 2.5 oz): the list's steps between the three heights are the necks' metal, about what the drawn steps are."],"ledger":["geissele-super-precision-micro-lower-13.optical_axis_above_rail","geissele-super-precision-micro-lower-13.deck_above_rail","geissele-super-precision-micro-lower-13.fence_top_above_rail","geissele-super-precision-micro-lower-13.mount_length","geissele-super-precision-micro-lower-13.plate_length","geissele-super-precision-micro-lower-13.clamp_below_rail","geissele-super-precision-micro-lower-13.width_over_nut","geissele-super-precision-micro-lower-13.lug_spacing"]},"profiles":{},"gaps":[{"what":"This height's height","need":"Geissele's own figure, or a drawing of this height: its sellers say 1.59 (Primary Arms) and 1.70 in to the optic's centerline (Rooftop Defense), and its own photos put a T-2 at about 1.47 to 1.50"},{"what":"Geissele's own drawing, figures and instruction sheet","need":"geissele.com refuses the reader: its spec page and instructions (the dot's screws and their torque) would replace the sellers' quotations and the photos' readings"},{"what":"Which dot the height is for","need":"A page that names it: Primary Arms titles the mount for the T2, Geissele's text names the T1"},{"what":"Where on the rail it goes","need":"A maker's sentence (receiver only, not across the rail's seam): none on any page read"}]},"guntec-ar15-carbine-buffer":{"id":"guntec-ar15-carbine-buffer","name":"AR-15 Mil-Spec Car Buffer","manufacturer":"Guntec USA","sku":"CARBUF","url":"https://guntecusa.com/product/ar-15-mil-spec-car-buffer/","category":"buffer","description":"The buffer in Guntec's mil-spec buffer tube set, also sold alone: the weight inside the receiver extension that the bolt carrier pushes back against. Guntec: \"CAR/M4 Mil-Spec Buffer\", \"Steel Weights\", \"3.0 oz weight\", \"Aluminum Body, White Neoprene Head\". The user, who owns the set, of the buffer in theirs (2026-10-20): \"Gold, white bumper\". The set's sellers: \"Includes End Plate, Castle Nut, 3 oz CAR Buffer, & Upgraded Chrome Silicon Spring\" (The Country Shed).","weight":"guntec-ar15-carbine-buffer.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"bore":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the buffer's axis at its head's front face, +x rearward."}},"interfaces":{"bore":{"type":"ar15.extension_bore","role":"buffer","anchor":"bore","params":{},"flips":false}},"materials":{"body":{"label":"Buffer body","finish":"anodized_matte","recolorable":false,"color":"guntec-buffer-anodize","note":"Guntec: \"Aluminum Body\", \"Material Grade: 6061\", \"Finish: Anodized\", \"Color: Gold\". A pale champagne gold in Midwest Gun Works' square picture of it (af72b3d271e9), which the colour is fitted to, and in its picture of the set (657de6718f20); pinker under Guntec's own studio light (7c97d3ec96e9, its lit band #ecd7c2, an oblique) and in Guntec's 2019 picture of its purple set (0ab407ab3350). The user, of the set they own: \"Gold, white bumper\". Sold in the one colour. Guntec's 2019 layout of its red set (53eee351ef23) has the same buffer with a black body: not offered, no page selling it so."},"bumper":{"label":"Bumper","finish":"polymer","recolorable":false,"color":"guntec-buffer-bumper","note":"Guntec: \"White Neoprene Head\" (\"Material: Aluminum , Neoprene , Steel\"). A translucent white in Guntec's and Midwest Gun Works' pictures (7c97d3ec96e9, af72b3d271e9, 657de6718f20). Drawn opaque under `polymer`, as BCM's cream urethane bumper is."},"pin":{"label":"Pin","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"The pin through the body and the bumper: bright, a split pin's end, in Midwest Gun Works' picture (af72b3d271e9)."}},"components":{},"geometry":{"model":"guntec-ar15-carbine-buffer.glb","components":{},"approximations":["The standard carbine buffer's pattern (lib.carbine_buffer: the Army's drawings of the rifle buffer's head, bumper and pin, the reference CAD set's carbine body), its body drawn 0.17 in longer, to the 3.42 in that two photographs of Guntec's buffer read (the ledger's `length`): the head, its three flats, the step the spring sits over, the body's diameter, the bumper and the pin are the standard's. Midwest Gun Works' picture has the head's flange reading thicker than the standard's (about 0.3 in against 0.254 at the head's scale) and the bumper 0.42 out where the standard's is 0.40: not drawn.","Not drawn: the weights inside it (Guntec's description: \"Steel Weights\"; its page's title: \"AR-15 Mil-Spec Car Buffer with Tungsten and Steel Weights\"; the two disagree, and the weight is Guntec's 3.0 oz either way), the dimple or mark on its face, any lettering.","In a build its face rests where the bolt carrier's rear end stands with the bolt forward, at the upper receiver's rear face, as every carbine buffer's does."],"ledger":["guntec-ar15-carbine-buffer.length","guntec-ar15-carbine-buffer.body_length","guntec-ar15-carbine-buffer.od","std.carbine_buffer.head_thickness","std.carbine_buffer.body_d","std.carbine_buffer.bumper_exposed"]},"profiles":{},"gaps":[{"what":"Its own sizes","need":"Guntec's figures: its page states none; its length is two photographs' (3.42 in; Guntec's own picture, 7c97d3ec96e9, is an oblique and isn't read), its diameters and its head the standard's"}]},"guntec-ar15-castle-nut":{"id":"guntec-ar15-castle-nut","name":"AR-15 Castle Nut for CAR/M4 Buffer Tube","manufacturer":"Guntec USA","sku":"CASTLE","url":"https://www.cheaperthandirt.com/guntec-ar-15-castle-nut-for-carm4-buffer-tube-steel-black-finish/FC-714569643782.html","category":"castle_nut","description":"The nut on the receiver extension's thread that is turned down onto the end plate and locks the extension to the lower receiver, its four notches taking the wrench, with a radial hole in its side. Guntec, as Cheaper Than Dirt carries its words: \"Guntec has an AR-15 Castle Nut for Car/M4 Buffer Tube to provide more strength and durability for your AR. This castle nut is made with quality at an economical price. Made in the USA.\" \"Fits Mil-spec and Commercial Buffer Tubes\", \"US Made In Scottsdale, Arizona\", \"Steel\", \"Matte Black\". Thinner than a mil-spec nut: 0.29 in by its own thread on a photo, against the reference model's 0.3765 (Guntec's heavy duty nut, its \"Extra Wide\" one, is 0.375).","weight":"guntec-ar15-castle-nut.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"seat":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the tube axis at the nut's front face, which bears on the end plate, +x rearward."}},"interfaces":{"nut_seat":{"type":"ar15.end_plate_seat","role":"nut","anchor":"seat","params":{},"flips":false,"note":"Cheaper Than Dirt, Guntec's list: \"Fits Mil-spec and Commercial Buffer Tubes\"."}},"materials":{"nut":{"label":"Castle nut","finish":"phosphate","recolorable":false,"color":"steel-phosphate-black","note":"Steel, \"Matte Black\" (Cheaper Than Dirt's page, Guntec's list); which finish isn't said. Black in every photograph of it on file: Cheaper Than Dirt's of it alone (bd27a5b91cde, a little sheen), and beside the tube in sellers' pictures of Guntec's sets (Redcon1's red, references/guntec-ar15-castle-nut 2ab5455bdba9, and chrome, references/guntec-ar15-end-plate 59e737ecf3a6; ABC Sportz's gold, 0b3672e01b07). Drawn as a black phosphate by its look; one look."}},"components":{},"geometry":{"model":"guntec-ar15-castle-nut.glb","components":{},"approximations":["A ring bored to the extension's thread's crests (std.receiver_extension.thread_major_d), as BCM's nut is drawn: its own thread isn't drawn, and the bore's chamfers aren't.","Its four wrench notches are cut straight through the wall from the bore, square-floored, 90 degrees apart (counted on two photos; read 98, 81, 92 and 89 apart on the one that shows them all, within its reading's few degrees); one is put at the top, since how a nut is turned on its thread isn't fixed.","The radial hole is drawn through the wall to the thread (its depth is an assumption: no view shows its bottom), midway between two notches, at the middle of its thickness as Cheaper Than Dirt's photo has it.","What its front face has (a mil-spec nut has three staking notches in its outer edge) isn't drawn: no photo on file shows Guntec's nut's front face."],"ledger":["guntec-ar15-castle-nut.od","guntec-ar15-castle-nut.thickness","guntec-ar15-castle-nut.notches","guntec-ar15-castle-nut.notch_width","guntec-ar15-castle-nut.notch_depth","guntec-ar15-castle-nut.hole_d","guntec-ar15-castle-nut.hole_from_front"]},"profiles":{},"gaps":[{"what":"Its sizes","need":"Guntec's figures: every size here is read on Cheaper Than Dirt's photo (its own thread or its own diameter as the scale) and checked on Redcon1's"},{"what":"Its front face","need":"A photo of the nut's front face: whether it has staking notches"}]},"guntec-ar15-chrome-silicon-buffer-spring":{"id":"guntec-ar15-chrome-silicon-buffer-spring","name":"Upgraded Chrome Silicon Spring","manufacturer":"Guntec USA","url":"https://redcon1tactical.com/guntec-usa-ar-15-mil-spec-buffer-tube-kit-anodized-red.html","category":"buffer_spring","description":"The spring inside the receiver extension, round the buffer, that sends the bolt carrier forward again after each shot: the one in Guntec's mil-spec buffer tube set, and sold only in it. The set's sellers: \"Includes End Plate, Castle Nut, 3 oz CAR Buffer, & Upgraded Chrome Silicon Spring\" (The Country Shed, MILTUBESET-RED), \"The upgraded chrome silicon-coated spring allows for smoother and more efficient cycling\" and \"Spring Length: 11\\\" (Carbine)\" (Redcon1 Tactical).","weight":"guntec-ar15-chrome-silicon-buffer-spring.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"bore":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the receiver extension's axis where a buffer's front face rests, +x rearward."}},"interfaces":{"bore":{"type":"ar15.extension_bore","role":"buffer","anchor":"bore","params":{},"flips":false}},"materials":{"spring":{"label":"Spring","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"A bright, polished wire in every picture of the set on file, whatever the tube's colour (Guntec's layout of the red set 53eee351ef23 and its pictures of the clear and purple sets; Redcon1's, ABC Sportz's and Midwest Gun Works' pictures). The sellers' words: \"Upgraded Chrome Silicon Spring\" (The Country Shed), \"chrome silicon-coated spring\" (Redcon1 Tactical): chrome silicon is a spring wire's alloy, and the look is the bright metal the pictures show, drawn as `stainless`, which isn't fitted to a photograph."}},"components":{},"geometry":{"model":"guntec-ar15-chrome-silicon-buffer-spring.glb","components":{},"approximations":["Drawn as it is in a rifle: held between a carbine buffer's head and the rear wall inside the set's tube, 6.97 in long, where it is 11 in free (Redcon1 Tactical's figure; Guntec's own picture of it laid out beside the tube reads 12.1). Its 39 coils are counted on that picture, both ends closed; its wire (.072 in) and outside diameter (.940) are the standard carbine spring's (the Army's drawing of the rifle's action spring), which the picture bears out for the diameter and is too small to read for the wire.","Its end coils are closed, one turn at each end; any end coil reduced in diameter isn't drawn."],"ledger":["guntec-ar15-chrome-silicon-buffer-spring.wire_d","guntec-ar15-chrome-silicon-buffer-spring.od","guntec-ar15-chrome-silicon-buffer-spring.coils","guntec-ar15-chrome-silicon-buffer-spring.free_length","guntec-ar15-chrome-silicon-buffer-spring.installed_length"]},"profiles":{},"gaps":[{"what":"Its wire and its weight","need":"Guntec's figures (its pages refuse the reader: the user's saved copy of the set's page): the wire is the standard's, and 1.98 oz is worked out from it and the coils"},{"what":"Its free length","need":"Guntec's figure: Redcon1 Tactical's spec table says 11 in, Guntec's 2019 picture of the set reads 12.1"},{"what":"Sold alone?","need":"A page that ties it to a Guntec spring sold alone: a search names an 'AR-15 Chrome Car Stock Spring' (CH-SPR, \"Chrome/Teflon Coated\") on Guntec's site, which refuses the reader, and at OpticsPlanet, whose page gave the reader no product"}]},"guntec-ar15-end-plate":{"id":"guntec-ar15-end-plate","name":"AR-15 Receiver End Plate","manufacturer":"Guntec USA","sku":"ENDPLATE","url":"https://guntecusa.com/product/ar-15-receiver-end-plate/","category":"end_plate","description":"The plate between the castle nut and the lower receiver: a ring round the receiver extension with a lobe that covers the takedown pin's detent spring, a key in its hole that rides in the extension's slot, and a boss on the lobe. Guntec: \"US Made Steel\", \"Fits Mil-spec/Commercial Buffer Tubes\", \"Color: Black\", \"Finish: Nitride\", \"Material: Steel\"; UPC 714569652319. The end plate in Guntec's buffer tube set (The Country Shed, Guntec's words for the set: \"Includes End Plate, Castle Nut, 3 oz CAR Buffer, & Upgraded Chrome Silicon Spring\"), black in every colour of the set.","weight":"guntec-ar15-end-plate.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"end":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the tube axis at the plate's front face, which bears on the receiver's rear face, +x rearward."},"nut_seat":{"origin":["{.thickness}",0,0],"x":[1,0,0],"note":"The plate's rear face, where the castle nut bears."}},"interfaces":{"extension_end":{"type":"ar15.extension_end","role":"fitting","anchor":"end","params":{},"flips":false},"nut_seat":{"type":"ar15.end_plate_seat","role":"plate","anchor":"nut_seat","params":{},"flips":false}},"materials":{"plate":{"label":"End plate","finish":"nitride","recolorable":false,"color":"steel-nitride-black","note":"Guntec: \"Color: Black\", \"Finish: Nitride\", \"Material: Steel\" (its page as the user saved it, 2026-10-20): a black nitride, which its picture ENDPLATE_2048 shows as a dark, faintly blue steel. Black in every colourway's photograph of the set on file: the clear and purple sets in Guntec's own pictures (references/guntec-ar15-mil-spec-buffer-tube-gen-2 e0853c782418, 0ab407ab3350), the red set in Redcon1's photograph and Guntec's laid out (references/guntec-ar15-end-plate 2ab5455bdba9, 53eee351ef23), the gold, green and black sets in ABC Sportz's (0b3672e01b07, 5b0472c4b79d, c93432384473) and its 9 mm clear set (f505640b6f25), the bronze and OD green sets in ABC Sportz's (references/guntec-ar15-mil-spec-buffer-tube-gen-2 968ee3ecae9b, 7378f0bd1fb3; one of the two is the other recoloured, the black the same in both), and the chrome set (MILTUBESET-C) in Redcon1's (references/guntec-ar15-end-plate 59e737ecf3a6, its plate and nut the red set's photograph again, at 1.5 times the size). One look in every colourway of the set."}},"components":{},"geometry":{"model":"guntec-ar15-end-plate.glb","components":{},"approximations":["Its outline is the mil-spec plate's as the AR-15 CAD reference set draws it (a ring, a lobe with a round end, straight sides tangent to the lobe that meet the ring at a corner): Guntec states no size, and its pictures agree with that outline. Guntec's own ENDPLATE_2048 isn't square on (its hole 0.928 as tall as wide): read across, where the tilt changes nothing, its boss is 0.504 wide (the model's 0.496) and its ring 1.379 (1.363); read down through the hole's and the ring's own aspects, its top, lobe, boss, key and V within 0.02 to 0.03 of the model's. Redcon1's face-on photo of the set's plate has its lobe's bottom at the model's ratio to the ring (2.03 to 2.02); Guntec's own set pictures read its lobe 0.03 to 0.04 in short across the tube's axis, as a lens a little above or below a flat plate reads it.","Its thickness, the boss's and the dimple's depths, the key and the V either side of it are the reference model's: no picture on file shows the plate edge-on. Guntec's ENDPLATE_2048 and Redcon1's photo show the key at the hole's bottom and the hole's edge coming down to it in two straight lines, as the model has them.","Not drawn: the staking points, and the edge a stamping leaves rounded on one face and sharp on the other (both edges are broken alike).","Its boss stands 0.065 in out of its front face, into the receiver's rear face where the takedown pin's detent spring is: no lower in the catalog has that recess drawn, so the two models share that much, as BCM's plates do."],"ledger":["guntec-ar15-end-plate.thickness","guntec-ar15-end-plate.height","guntec-ar15-end-plate.top_above_axis","guntec-ar15-end-plate.bottom_below_axis","guntec-ar15-end-plate.lobe_radius","guntec-ar15-end-plate.lobe_centre_below_axis"]},"profiles":{},"gaps":[{"what":"Its sizes","need":"Guntec's figures, or a square-on picture of the plate with a scale: every size here is the reference model's mil-spec plate, which Guntec's pictures agree with to their two or three hundredths"}]},"guntec-ar15-heavy-duty-castle-nut":{"id":"guntec-ar15-heavy-duty-castle-nut","name":"AR-15 Heavy Duty Wide Castle Nut For Car/M4 Buffer Tube","manufacturer":"Guntec USA","sku":"CASTLE-HD","url":"https://guntecusa.com/product/ar15-heavy-duty-wide-castle-nut-for-car-m4-buffer-tube/","category":"castle_nut","description":"Guntec's wide castle nut: the nut on the receiver extension's thread that is turned down onto the end plate and locks the extension to the lower receiver, four notches in its rear face taking the wrench, and notches in its front face's edge where it is staked. Guntec: \"US Made Steel\", \"Gen 2\", \"Fits Mil-spec/Commercial Buffer Tubes\", \"Extra Wide For Stronger, More Durable Hold\", \"Color: Black\", \"Material: Steel\", \"Finish: Matte\", \"Product Height 0.375\"\", \"Product Width 1.3125\"\", \"Product Length 1.3125\"\", \"Product Weight 0.6 oz\"; UPC 714569647827. The castle nut in Guntec's buffer tube set, by the user who owns one.","weight":"guntec-ar15-heavy-duty-castle-nut.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"seat":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the tube axis at the nut's front face, which bears on the end plate, +x rearward."}},"interfaces":{"nut_seat":{"type":"ar15.end_plate_seat","role":"nut","anchor":"seat","params":{},"flips":false,"note":"Guntec: \"Fits Mil-spec/Commercial Buffer Tubes\"."}},"materials":{"nut":{"label":"Castle nut","finish":"phosphate","recolorable":false,"color":"steel-phosphate-black","note":"Guntec: \"Color: Black\", \"Material: Steel\", \"Finish: Matte\" (its saved page); which finish isn't said. Black and matte in its own picture (CASTLE-HD-1) and in Guntec's pictures of its clear and purple sets: drawn as a black phosphate by those words and that look. One look in every colourway of the set."}},"components":{},"geometry":{"model":"guntec-ar15-heavy-duty-castle-nut.glb","components":{},"approximations":["A ring of Guntec's diameter and thickness, bored to the extension's thread's crests (std.receiver_extension.thread_major_d), as every castle nut in the catalog is drawn: its own thread isn't drawn (its weight counts it), nor are the bore's chamfers.","Its four wrench notches are cut straight through the wall from the bore, square-floored, 90 degrees apart, the first at the top; their width and depth are read on Guntec's one 500 px picture, to two or three hundredths.","Its front face's notches: one is in view in Guntec's picture, midway between two wrench notches; three at 120 degrees are drawn, as a mil-spec nut has them and as the picture allows (the other two aren't in view). Each is cut from the outside to the mil-spec nut's 0.075 in, which opens into the bore drawn at the thread's crests."],"ledger":["guntec-ar15-heavy-duty-castle-nut.od","guntec-ar15-heavy-duty-castle-nut.thickness","guntec-ar15-heavy-duty-castle-nut.notches","guntec-ar15-heavy-duty-castle-nut.notch_width","guntec-ar15-heavy-duty-castle-nut.notch_depth","guntec-ar15-heavy-duty-castle-nut.staking_notches"]},"profiles":{},"gaps":[{"what":"Its front face notches' count","need":"A picture of its front face whole (the one on file shows its near half)"}]},"guntec-ar15-mil-spec-buffer-tube-gen-2":{"id":"guntec-ar15-mil-spec-buffer-tube-gen-2","name":"AR-15 Mil-Spec Buffer Tube (Gen 2)","manufacturer":"Guntec USA","sku":"MILTUBE-G2-CLEAR","url":"https://guntecusa.com/product/ar-15-mil-spec-buffer-tube-gen-2-anodized-clear/","category":"receiver_extension","description":"Guntec's mil-spec carbine buffer tube, the Gen 2, six positions, anodized aluminium in twelve colours, sold alone without its end plate, castle nut, buffer or spring. Guntec, every page of it: \"MIL-SPEC Gen 2 Tube Design With Notch Cut Out For Buffer Detent To Engage\", \"Six Position\", \"Compatible With SBA Tactical Braces\" (the coloured ones), \"US Made\", \"T6 Aluminum\", \"Weight: 3.3 oz\", \"Material Grade: 6061\", \"Caliber: .308 Caliber, 5.56 Caliber, 9mm Caliber\"; the black one, which Guntec calls Plain: \"Product Height 1.4375\"\", \"Product Width 1.125\"\", \"Product Length 7.25\"\", \"Product Weight 3.4 oz\". Sellers: \"GUNTEC AR-15|AR-10 MIL-SPEC BUFFER TUBE\" (the2ndtactical.com, \"6 POSITION\", \"CARBINE\", \"MIL-SPEC\", \"FITS AR15 AND AR10\"); \"6-position carbine-length Mil-Spec receiver extension machined from T6-6061 aluminum\" (Redcon1 Tactical, Guntec's red set). The notch shows in every photo on file as a slot through the thread's crests under the mouth at six o'clock, and Guntec's close-ups of the black one show a small notch in the rim there.","weight":"guntec-ar15-mil-spec-buffer-tube-gen-2.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"receiver_thread":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the tube axis at the takedown pin's X, +x rearward."},"tube":{"origin":[0,0,0],"x":[1,0,0]},"end":{"origin":["0in - {std.ar15.receiver_rear_x}",0,0],"x":[1,0,0],"note":"On the tube axis at the receiver's rear face (the Army's drawing of the lower), where an end plate bears."},"bore":{"origin":["0in - {std.ar15.upper_rear_face_x}",0,0],"x":[1,0,0],"note":"On the tube axis where a buffer's front face rests with the bolt forward: against the carrier's rear end, which stands at the upper receiver's rear face (the Army's drawings). The buffer and its spring are placed from it."}},"interfaces":{"receiver_thread":{"type":"ar15.buffer_tube_mount","role":"tube","anchor":"receiver_thread","params":{},"flips":false,"note":"the2ndtactical: \"FITS AR15 AND AR10\" (the AR-10's is another tube; on file only the AR-15's lower)."},"tube":{"type":"receiver_extension","role":"tube","anchor":"tube","params":{"profile":"mil-spec","od":"={.tube_od}","positions":6,"step":"={.position_step}"},"flips":false,"note":"Sold as mil-spec, six positions (the2ndtactical: \"MIL-SPEC\", \"6 POSITION\", \"CARBINE\"; Redcon1: \"Type: Mil-Spec 1.148\\\"\")."},"extension_end":{"type":"ar15.extension_end","role":"tube","anchor":"end","params":{},"flips":false},"bore":{"type":"ar15.extension_bore","role":"tube","anchor":"bore","params":{},"flips":false}},"materials":{"tube":{"label":"Receiver extension","finish":"anodized","recolorable":false,"color":"guntec-anodized-clear","options":{"clear":{"label":"Anodized Clear","finish":"anodized","color":"guntec-anodized-clear","sku":"MILTUBE-G2-CLEAR","source":"https://guntecusa.com/product/ar-15-mil-spec-buffer-tube-gen-2-anodized-clear/"},"red":{"label":"Anodized Red","finish":"anodized","color":"guntec-anodized-red","sku":"MILTUBE-G2-RED","source":"https://guntecusa.com/product/ar-15-mil-spec-buffer-tube-gen-2-anodized-red/"},"gold":{"label":"Anodized Gold","finish":"anodized","color":"guntec-anodized-gold","sku":"MILTUBE-G2-GOLD","source":"https://guntecusa.com/product/ar-15-mil-spec-buffer-tube-gen-2-anodized-gold/"},"black":{"label":"Anodized Black","finish":"anodized","color":"placeholder-black","sku":"MILTUBE-G2","source":"https://guntecusa.com/product/ar-15-mil-spec-buffer-tube-gen-2-plain/"},"blue":{"label":"Anodized Blue","finish":"anodized","color":"guntec-anodized-blue","sku":"MILTUBE-G2-BLUE","source":"https://guntecusa.com/product/ar-15-mil-spec-buffer-tube-gen-2-anodized-blue/"},"bronze":{"label":"Anodized Bronze","finish":"anodized","color":"guntec-anodized-bronze","sku":"MILTUBE-G2-BRZ","source":"https://guntecusa.com/product/ar-15-mil-spec-buffer-tube-gen-2-anodized-bronze/"},"green":{"label":"Anodized Green","finish":"anodized","color":"guntec-anodized-green","sku":"MILTUBE-G2-GREEN","source":"https://guntecusa.com/product/ar-15-mil-spec-buffer-tube-gen-2-anodized-green/"},"grey":{"label":"Anodized Grey","finish":"anodized","color":"guntec-anodized-grey","sku":"MILTUBE-G2-GREY","source":"https://guntecusa.com/product/ar-15-mil-spec-buffer-tube-gen-2-anodized-grey/"},"irish-green":{"label":"Anodized Irish Green","finish":"anodized","color":"guntec-anodized-irish-green","sku":"MILTUBE-G2-IG","source":"https://guntecusa.com/product/ar-15-mil-spec-buffer-tube-gen-2-anodized-irish-green/"},"orange":{"label":"Anodized Orange","finish":"anodized","color":"guntec-anodized-orange","sku":"MILTUBE-G2-ORANGE","source":"https://guntecusa.com/product/ar-15-mil-spec-buffer-tube-gen-2-anodized-orange/"},"pink":{"label":"Anodized Pink","finish":"anodized","color":"guntec-anodized-pink","sku":"MILTUBE-G2-PINK","source":"https://guntecusa.com/product/ar-15-mil-spec-buffer-tube-gen-2-anodized-pink/"},"purple":{"label":"Anodized Purple","finish":"anodized","color":"guntec-anodized-purple","sku":"MILTUBE-G2-PURPLE","source":"https://guntecusa.com/product/ar-15-mil-spec-buffer-tube-gen-2-anodized-purple/"}},"default":"clear","note":"One piece of aluminium, anodized in the colour it is sold in. Guntec, every page of it: \"Anodized <colour> Finish\", \"Finish: Anodized\", \"T6 Aluminum\", \"Material Grade: 6061\"; the type and class of the anodize aren't stated. Guntec sells this tube in twelve colours, each its own page and number at $32.95 (its pages as the user saved them, 2026-10-19, under references/guntec-ar15-mil-spec-buffer-tube-gen-2/docs/), and all twelve are offered. Its gallery is eleven photographs of the tube in one pose in one studio, one a colour (not one picture recoloured: after the best shift their edges agree at 0.26 to 0.63 where a picture with itself gives 1; the2ndtactical's copies are the same photographs). Every coloured preset is fitted on Guntec's own photograph of the tube in that colour, the same stretch of each, through one treatment for that studio (its blue light taken out by making the clear anodize neutral, its white ground put on the app's backdrop): data/colors/guntec-usa.yaml says how, and what the batch-12 fits on photographs of Guntec's sets were. The black is the finish's look. The \"Plain\" in black is the same tube: its page's title, description, number and price are the coloured ones' but for \"Compatible With SBA Tactical Braces\", which only the coloured pages say."}},"components":{},"geometry":{"model":"guntec-ar15-mil-spec-buffer-tube-gen-2.glb","components":{},"approximations":["The tube is the mil-spec carbine extension's, from the ledger: its outside the standard's 1.148, its length Magpul's drawing of the tube (7.25), its front face where the Army's drawings put a mil-spec tube's, its thread the standard's 1 3/16-16 (a helix between the Army drawing's limits, as long as the reference model's carbine tube's), bored to the drawing's inch to a rear wall of the reference model's 0.072 with its 0.094 hole. No view on file shows Guntec's rear end; the reference model's wall and hole are assumed for it.","The rail under it is the standard's (Magpul's drawing: its width, its depth below the axis, its 45° front ramp). Along its underside a shallow channel with rounded ends, the six holes in its floor: its ends read on the clear tube's picture (0.45 and 3.82 in ahead of the rear face), its width and depth assumed (0.25, 0.03): no view on file shows the underside square on.","The six holes are a mil-spec tube's, at the stock's step (Magpul's 0.66), their size and the rear one's place taken as read on BCM's tube (assumed: no view on file shows Guntec's square on), drilled up from the channel's floor to the tube's wall.","The notch Guntec calls \"Notch Cut Out For Buffer Detent To Engage\" is drawn as the standard's key slot at six o'clock under the thread (the reference model's width, floor and length): that is where every photo on file shows it, a slot through the thread's crests at the bottom of the mouth (the clear tube's picture, Redcon1's red one). Its own sizes aren't stated or read.","The rail's rear lower edge is cut off, as every photo on file that shows it has it: 0.10 in along the tube on the clear tube's picture, drawn at 45° (assumed: no view is square to the rail's side).","The thread is the standard's length: its crests, counted on the clear tube's picture and on Redcon1's photograph of the red one, are 18 to 19, where the standard's 1.181 in at 16 to the inch is 18.9 (thread_crests).","Not drawn: the rail's lip ahead of the ramp and its fillets, the plain lip at the mouth ahead of the thread's first crest, any chamfer in the mouth, and Guntec's marks."],"ledger":["guntec-ar15-mil-spec-buffer-tube-gen-2.tube_od","guntec-ar15-mil-spec-buffer-tube-gen-2.tube_length","guntec-ar15-mil-spec-buffer-tube-gen-2.tube_front_behind_pin","guntec-ar15-mil-spec-buffer-tube-gen-2.position_step","guntec-ar15-mil-spec-buffer-tube-gen-2.position_hole_d","guntec-ar15-mil-spec-buffer-tube-gen-2.position_hole_rear_from_rear","guntec-ar15-mil-spec-buffer-tube-gen-2.channel_rear_from_rear","guntec-ar15-mil-spec-buffer-tube-gen-2.channel_front_from_rear","guntec-ar15-mil-spec-buffer-tube-gen-2.channel_width","guntec-ar15-mil-spec-buffer-tube-gen-2.channel_depth","guntec-ar15-mil-spec-buffer-tube-gen-2.rail_rear_chamfer"]},"profiles":{},"gaps":[{"what":"The notch at the mouth's rim (\"Notch Cut Out For Buffer Detent To Engage\"): Guntec's two close-ups of the black tube (12b14516ed50, 0979efec9f6c) show it, small and square, and a slot through the thread's crests beside it; the model has the standard's key slot and no notch in the rim","need":"the notch read on those close-ups against the thread's pitch (a known size in their plane), or a view of the mouth square on"},{"what":"The weight: Guntec states 3.3 oz (and 3.4 as the black tube's Product Weight), the metal worked out from the mil-spec sizes is 3.6","need":"a review that weighs the tube alone, or the wall's and the channel's own sizes"},{"what":"The holes' size and place, the channel's width and depth, and the rear end","need":"a photograph of the underside and the rear end square on, with a known size in frame"},{"what":"Every colour rests on one studio's photographs and a treatment that takes the clear anodize for neutral grey and the studio's cut-out white ground for its exposure: nothing on file checks either","need":"a second studio's photograph of the tube alone in any colour, with a neutral (a black end plate, a grey card) in frame"}]},"guntec-ar15-stainless-carbine-buffer":{"id":"guntec-ar15-stainless-carbine-buffer","name":"AR-15 Stainless Steel Car Buffer","manufacturer":"Guntec USA","sku":"CARBUF-SS","url":"https://guntecusa.com/product/ar-15-stainless-steel-car-buffer/","category":"buffer","description":"Guntec's stainless steel carbine buffer, the weight inside the receiver extension that the bolt carrier pushes back against. Guntec: \"CAR/M4 Standard Buffer\", \"No Moving Internal Weights, One Solid Unit\", \"3.2 oz weight\", \"Reduces Noise and Friction Compared To Standard Buffers\", \"Mil-Spec Dimensions\", \"Stainless Steel, Black Neoprene Head\".","weight":"guntec-ar15-stainless-carbine-buffer.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"bore":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the buffer's axis at its head's front face, +x rearward."}},"interfaces":{"bore":{"type":"ar15.extension_bore","role":"buffer","anchor":"bore","params":{},"flips":false}},"materials":{"body":{"label":"Buffer body","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"Guntec: \"Stainless Steel\", \"Color: Stainless Steel\", \"Finish: Satin\". A satin bright metal in Guntec's picture of it (627dce494537) and in the sellers' pictures of the set that have it (Redcon1's eabe3e83f28b, 422762ebd1ef; ABC Sportz's). Bright metal isn't fitted to a photograph: its finish type is its look. Sold in the one finish."},"bumper":{"label":"Bumper","finish":"rubber","recolorable":false,"color":"placeholder-polymer-black","note":"Guntec: \"Black Neoprene Head\" (\"Material: Neoprene , Steel\"). Black in its picture (627dce494537: #525266 on its lit side, under that studio's blue cast) and in Redcon1's (#222125). A black isn't fitted: the catalog's stand-in black, under `rubber`."},"pin":{"label":"Pin","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"The pin through the body and the bumper: its hole beside the bumper in Guntec's picture (627dce494537), the pin's end as bright as the body."}},"components":{},"geometry":{"model":"guntec-ar15-stainless-carbine-buffer.glb","components":{},"approximations":["The standard carbine buffer's shape (lib.carbine_buffer: the Army's drawings of the rifle buffer's head, bumper and pin, and the reference CAD set's carbine body), at the standard's length and diameters, by Guntec's \"Mil-Spec Dimensions\". Its pictures are obliques and give no size; their pattern is the standard's: the head with a flat on its rim, the step behind it, the pin's hole beside a tapered bumper with a flat end.","Drawn solid. Guntec: \"No Moving Internal Weights, One Solid Unit\" and \"3.2 oz weight\": stainless steel the standard's outside would weigh 5.8 oz, so its inside is hollowed by about 0.6 cubic inch, which no page or picture shows and which isn't drawn.","Not drawn: the mark on its face.","In a build its face rests where the bolt carrier's rear end stands with the bolt forward, at the upper receiver's rear face, as every carbine buffer's does."],"ledger":["guntec-ar15-stainless-carbine-buffer.length","guntec-ar15-stainless-carbine-buffer.od","std.carbine_buffer.head_thickness","std.carbine_buffer.body_d","std.carbine_buffer.bumper_exposed"]},"profiles":{},"gaps":[{"what":"Its inside","need":"Guntec's figure or a section: \"One Solid Unit\" at 3.2 oz is hollow by about half its outside's volume"},{"what":"Its own sizes","need":"Guntec's figures: \"Mil-Spec Dimensions\" gives it the standard's"}]},"hexmag-series-2-ar15-30":{"id":"hexmag-series-2-ar15-30","name":"AR-15/M4/M16 Magazine Series 2 (30RD)","manufacturer":"Hexmag","sku":"HX30-AR15S2","category":"magazine","description":"Hexmag's Series 2 30-round polymer magazine for AR-15/M4/M16 rifles in 5.56 NATO, .223 Remington and .300 Blackout, with its raised hexagon grip (HEXTURE) and an orange follower and HexID latch plate; sold in black, gray, Flat Dark Earth and OD Green.","weight":"hexmag-series-2-ar15-30.weight","cartridge":{"takes":["5.56 NATO",".223 Rem",".300 Blackout"],"stated":"CALIBERS: 5.56 X 45 NATO, 223 REMINGTON, 300 AAC BLACKOUT","source":"https://hexmag.com/product/hexmag-ar-15-m4-m16-magazine-series-2-30-rds/ (Hexmag's TECH SPECS for HX30-AR15S2, as cached: harvest.quote)"},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"magwell":{"origin":["{.spine_ahead_of_rearmost}","-{.catch_notch_top}",0],"note":"The upper edge of its catch notch, at its spine's rear face where it stands in the well: what hangs on the lower's catch, in the well's spine slot. Magazine frame: origin at the rear face of the spine at the top of the feed lips; the traced side profile's origin is its rearmost point, which on this magazine is the spine itself in the well (spine_ahead_of_rearmost, 0: the patent's side elevation has nothing behind the spine under the well, where the PMAG has its stop)."}},"interfaces":{"magwell":{"type":"ar15.magwell","role":"magazine","anchor":"magwell","params":{"family":"5.56"},"flips":false}},"materials":{"body":{"label":"Magazine body and floorplate","finish":"polymer","recolorable":false,"color":"placeholder-polymer-black","sheen":"matte","options":{"black":{"label":"Black","finish":"polymer","color":"placeholder-polymer-black","sheen":"matte","sku":"HX30-AR15S2-BLK","source":"https://www.primaryarms.com/hexmag-30-round-magazine-series-2-blk-hx30-ar15s2-blk"},"gray":{"label":"Gray","finish":"polymer","color":"hexmag-gray","sheen":"matte","sku":"HX30-AR15S2-GRY","source":"https://classicfirearms.com/hexmag-30-ar-m4-223-rem-556-gray-hx30argry"},"fde":{"label":"Flat Dark Earth","finish":"polymer","color":"hexmag-fde","sheen":"matte","sku":"HX30-AR15S2-FDE","source":"https://www.primaryarms.com/hexmag-30-round-magazine-series-2-fde-hx30-ar15s2-fde"},"odg":{"label":"OD Green","finish":"polymer","color":"hexmag-odg","sheen":"matte","sku":"HX30-AR15S2-ODG","source":"https://www.primaryarms.com/hexmag-30-round-magazine-series-2-odg-hx30-ar15s2-odg"}},"default":"black","note":"The four bodies Hexmag's page offers HX30-AR15S2 in (\"Magazine Color: Gray, Flat Dark Earth, Black, OD Green\"; its TECH SPECS: \"COLORS: Black, FDE, Gray, OD Green\"); the page names no number a colour, and sellers' pages give HX30-AR15S2-GRY (Classic Firearms, which calls it \"Dark Gray\"; Blackstone; Shiner), -BLK, -FDE and -ODG (Primary Arms). Its finish is the body's moulded polymer: \"CONSTRUCTION: POLYHEX2 Advanced Composite\" (Hexmag), \"Black reinforced polymer body\" (Primary Arms). In every colour the floorplate is the body's colour (Primary Arms' photographs of the black, FDE and OD Green ones, the _00 and _01 of each; Blackstone's of the gray, which has one lying on its side with its floorplate turned to the lens). The black one isn't fitted: it is drawn as the catalog's black polymer (Primary Arms' studio photographs it as a mid grey, #6e6e70 on the flat the others are read on). Hexmag also sells this body as its HexView (clear) and in printed patterns on its own site: other products, not colourways of this one. The gray: the sellers' photographs of HX30-AR15S2-GRY disagree, read on the same flat of the left side (under the lips' block or the catch's window): Blackstone Shooting's #5d6169 (62f3a85ef619, a bluish slate), AmmunitionStore's #3c413a (a82d374cd9a2, a charcoal, greener), Classic Firearms' #7a7a7a (6806412b151e, neutral, its right side). Hexmag has no photograph of the gray on its page. Fitted to Blackstone's: the sharpest and largest file of the three, an unretouched studio photograph with two magazines and their shadows; AmmunitionStore's is a soft 2019 file and Classic's a small, clean picture (perhaps a render). All three are the Series 2 (the guides, the front channel, the window and the panels where Primary Arms' Series 2 has them). Drawn so, the gray is lighter and bluer than Magpul's Stealth Gray beside it, near MAS Defense's (hexmag-gray's note)."},"hexid":{"label":"Follower and HexID latch plate","finish":"polymer","recolorable":false,"color":"hexmag-orange","sheen":"matte","note":"The follower, seen between the feed lips, and the HexID latch plate in the floorplate are orange in every colourway: \"STANDARD MAGAZINE IS BLACK BODY WITH ORANGE FOLLOWER\" (Hexmag's page), \"POLYHEX2 mags come standard with a orange latch plate and follower unless specified differently at check out\" (hexmag.com/polyhex2-magazines/); sellers' pages of the gray one: \"Grey with Orange Follower\" (Blackstone), and every photograph on file has them orange. Hexmag's own shop sells them in other HexID colours (\"HexID Color: Red, Black, Blue, Flat Dark Earth, Green, Yellow, Orange, Pink\"), a choice no seller on file offers and no photograph on file shows: not offered."}},"components":{},"geometry":{"model":"hexmag-series-2-ar15-30.glb","components":{},"approximations":["A visual hull of the design patent the magazine bears in its name block (US D727,456 S, \"PATENT D727,456 S\": Primary Arms' photo f9da4bea084e), its side elevation (FIG. 2, the side with the catch notch) and its rear elevation (FIG. 4), scaled by what it has to fit (overall_height, adopted from the well: 7.366 in, beside Hexmag's published 7.5). The patent was filed in 2013, before the Series 2; its silhouette fitted to Primary Arms' near-straight photograph of the Series 2's left side (scale and turn free) lies on the photo's with IoU 0.96, and the photo traced as a side outline lies on the patent's with IoU 0.973 (the difference the top, which the photo sees from above). Every section along the magazine is the rear elevation's: where the upper body's step to the gripping section is drawn level all round (at the rear elevation's height, 2.82 in under the top), the patent's side elevation has it falling 0.17 in from the front to the rear.","Its scale (2026-11-03, round 2): read at Hexmag's 7.5 in as an upright height, the drawing's top section is 2.576 in from the spine to the front, and seated where every lower on file seats a magazine's spine its front stood 0.043 in through the well's front wall (0.09 to 0.1 cubic inches shared with each lower). What it has to fit decides: the drawing is scaled so its top section's greatest reach from the spine (its front face is upright to a pixel) meets the well's front wall from that seat, 7.366 in tall, 1.8% under Hexmag's figure, which is kept beside it as published (likeliest the height rounded to the half inch). At that scale the top section is 0.887 across in a .898 well and its body ahead of the spine 2.385 in a 2.398 box; seated, it shares 0.0074 and 0.0060 cubic inches with the Workhorse and the Super Duty, as the PMAGs do. Every figure read on the patent is at that scale.","The HEXTURE: on each side the patent's 28 panels of one honeycomb (fourteen whole hexagons, the rest cut short at the front strip, the spine and the floorplate) and the two in the channel down the front of the upper body, each where the patent draws it (its lattice fitted to its twelve whole hexagons to 0.7 px); each panel stands out of a groove round it as wide as the lattice's band between two panels (0.082 in). HOW FAR they stand out is assumed (hex_proud, 0.03 in: KYGUNCO's \"raised hexagon grip pattern\"; no view on file has a panel's edge in profile). The right side's panels are its own elevation's (FIG. 3), the mirror of the left's within the trace.","The spine: behind the body's rear face (spine_depth, 0.148 in, the side elevation's and the plan's) only the spine's own width (spine_width, 0.465) stands, from the top of the lips down to the gripping section (grip_top), so that only the spine is in the well's slot for it; below, the rear's bars stand across the strip as the side outline's teeth carry them.","The catch's window on the left: its upper edge where the magazine hangs (catch_notch_top, read on the Series 2's photo; the patent's window is drawn 0.043 in lower and the model's window is the ledger's), its rear and front ends and its height the patent's, drawn as a pocket as deep as a lower's catch slot is cut (std.ar15.mag_catch_slot_floor) and not through; its corners rounded a sixth of its height (unsized). The block the rear elevation draws standing 0.049 in out of the left side under the window is not drawn: as read it would stand in a standard well's left wall (catch_block_proud), as the PMAG's does.","The stripper-clip guides: the two wedges at the top of the front each side, where the patent draws them, sunk 0.04 in (assumed: vee_depth).","The floorplate: under a joint floorplate_height above the side outline's underside and parallel to it (15.4 degrees), its section square to that lean: the rear elevation's rounded underside, full width, and the rear elevation's flare in to the gripping section's width at the joint. The rear elevation sees the leaning floorplate end on, so the flare's and the round's heights are read off a projection of the whole plate: approximate.","The follower is drawn as the top of the solid between the lips, 0.06 in of it (assumed: follower_thickness), at the floor of the notch the rear elevation draws between them (where the patent draws the follower in broken lines); the HexID latch plate as a hexagon flush in a pocket in the middle of the floorplate's underside, its size the bottom plan's (hexid_across), the pocket 0.05 in deep (assumed). Both in the hexid slot, orange.","Not drawn: the name block and every marking (\"5.56x45mm NATO\" on the left), the dimples and round marks, the floorplate's own panels and its release, the follower's shape and the lips' inner edges, the rounds; the model is solid (closed between the lips at the follower), so its volume is no polymer weight: 16.0 cubic inches of solid, where Hexmag's 4.55 oz is a hollow shell, a spring and a follower."],"ledger":["hexmag-series-2-ar15-30.overall_height","hexmag-series-2-ar15-30.front_to_back","hexmag-series-2-ar15-30.width","hexmag-series-2-ar15-30.grip_width","hexmag-series-2-ar15-30.floorplate_width","hexmag-series-2-ar15-30.catch_notch_top","hexmag-series-2-ar15-30.catch_notch_height","hexmag-series-2-ar15-30.catch_notch_rear_x","hexmag-series-2-ar15-30.catch_notch_front_x","hexmag-series-2-ar15-30.hang_below_magwell","hexmag-series-2-ar15-30.spine_depth","hexmag-series-2-ar15-30.spine_width","hexmag-series-2-ar15-30.grip_top","hexmag-series-2-ar15-30.hex_panels","hexmag-series-2-ar15-30.hex_panels_front","hexmag-series-2-ar15-30.hex_band","hexmag-series-2-ar15-30.hex_proud","hexmag-series-2-ar15-30.vee_depth","hexmag-series-2-ar15-30.floorplate_height","hexmag-series-2-ar15-30.follower_thickness","hexmag-series-2-ar15-30.hexid_across","hexmag-series-2-ar15-30.hexid_depth"]},"profiles":{"side":{"plane":"xy","origin":"the outline's rearmost point at the top of the feed lips (the left side, mirrored to face +x)","offset":{},"points":[[0,-0.483],[0.003,-1.869],[0.033,-2.618],[0.066,-3.063],[0.066,-3.099],[0.046,-3.119],[0.046,-3.155],[0.076,-3.195],[0.086,-3.363],[0.066,-3.386],[0.066,-3.409],[0.099,-3.462],[0.115,-3.624],[0.096,-3.643],[0.092,-3.67],[0.125,-3.716],[0.142,-3.864],[0.142,-3.888],[0.122,-3.911],[0.122,-3.94],[0.155,-3.983],[0.175,-4.151],[0.152,-4.181],[0.155,-4.207],[0.185,-4.234],[0.208,-4.409],[0.188,-4.435],[0.188,-4.465],[0.221,-4.498],[0.247,-4.676],[0.228,-4.696],[0.224,-4.712],[0.231,-4.735],[0.261,-4.762],[0.287,-4.923],[0.287,-4.937],[0.267,-4.956],[0.267,-4.979],[0.303,-5.026],[0.33,-5.184],[0.31,-5.23],[0.317,-5.253],[0.346,-5.28],[0.379,-5.454],[0.36,-5.477],[0.36,-5.504],[0.396,-5.54],[0.429,-5.708],[0.409,-5.751],[0.416,-5.774],[0.449,-5.811],[0.482,-5.969],[0.462,-6.012],[0.468,-6.032],[0.501,-6.061],[0.515,-6.114],[0.538,-6.22],[0.538,-6.236],[0.521,-6.256],[0.521,-6.279],[0.561,-6.322],[0.597,-6.487],[0.581,-6.513],[0.581,-6.536],[0.62,-6.576],[0.66,-6.744],[0.643,-6.771],[0.643,-6.79],[0.683,-6.84],[0.726,-7.001],[0.709,-7.025],[0.709,-7.051],[0.749,-7.091],[0.765,-7.147],[0.782,-7.209],[0.762,-7.242],[0.769,-7.265],[0.802,-7.295],[0.815,-7.345],[0.833,-7.366],[0.882,-7.356],[0.942,-7.363],[3.248,-6.729],[3.307,-6.69],[3.353,-6.68],[3.365,-6.649],[3.309,-6.451],[3.271,-6.413],[3.241,-6.409],[3.223,-6.391],[3.233,-6.355],[3.2,-6.312],[3.177,-6.226],[3.163,-6.17],[3.173,-6.154],[3.173,-6.121],[3.144,-6.091],[3.111,-5.956],[3.121,-5.9],[3.088,-5.854],[3.058,-5.718],[3.068,-5.669],[3.038,-5.633],[3.005,-5.484],[3.022,-5.451],[3.015,-5.431],[2.989,-5.405],[2.969,-5.316],[2.959,-5.253],[2.972,-5.223],[2.966,-5.2],[2.942,-5.177],[2.913,-5.026],[2.926,-5.009],[2.926,-4.983],[2.9,-4.95],[2.87,-4.798],[2.886,-4.772],[2.883,-4.748],[2.857,-4.719],[2.843,-4.65],[2.834,-4.584],[2.843,-4.521],[2.817,-4.491],[2.794,-4.346],[2.81,-4.306],[2.801,-4.277],[2.781,-4.257],[2.761,-4.115],[2.774,-4.085],[2.774,-4.059],[2.748,-4.026],[2.731,-3.907],[2.728,-3.871],[2.745,-3.851],[2.745,-3.835],[2.741,-3.818],[2.718,-3.795],[2.702,-3.66],[2.702,-3.637],[2.715,-3.624],[2.715,-3.591],[2.692,-3.564],[2.688,-3.544],[2.675,-3.406],[2.692,-3.386],[2.692,-3.366],[2.669,-3.333],[2.659,-3.264],[2.652,-3.175],[2.669,-3.155],[2.669,-3.129],[2.646,-3.099],[2.642,-3.076],[2.632,-2.944],[2.649,-2.924],[2.649,-2.898],[2.626,-2.868],[2.616,-2.687],[2.533,-2.575],[2.53,-0.328],[2.517,-0.315],[2.514,-0.229],[2.03,-0.228],[1.968,-0.208],[1.948,-0.224],[1.912,-0.191],[1.889,-0.185],[1.897,-0.2],[1.869,-0.228],[1.842,-0.228],[1.829,-0.214],[1.773,-0.214],[1.76,-0.228],[1.74,-0.228],[1.72,-0.214],[1.654,-0.218],[1.476,-0.175],[1.377,-0.132],[1.268,-0.069],[1.25,-0.051],[1.255,-0.043],[1.229,-0.043],[1.176,0],[0.17,-0.003],[0.148,-0.038],[0.145,-0.209],[0.127,-0.228],[0.096,-0.233],[0.092,-0.345],[0.036,-0.407],[0.033,-0.463],[0.015,-0.482]],"features":{"hexes":[[[0.299,-2.077],[0.533,-2.301],[0.536,-2.317],[0.454,-2.614],[0.427,-2.631],[0.19,-2.693],[0.18,-2.654],[0.18,-2.624],[0.186,-2.618],[0.18,-2.581],[0.18,-2.113],[0.216,-2.096]],[[1.413,-1.78],[1.641,-2.001],[1.644,-2.024],[1.572,-2.301],[1.555,-2.327],[1.249,-2.41],[1.018,-2.182],[1.021,-2.146],[1.09,-1.885],[1.11,-1.859]],[[0.945,-2.248],[1.179,-2.482],[1.1,-2.779],[1.087,-2.796],[0.8,-2.875],[0.777,-2.875],[0.549,-2.651],[0.553,-2.604],[0.622,-2.35],[0.635,-2.331]],[[0.477,-2.716],[0.691,-2.928],[0.684,-2.934],[0.708,-2.957],[0.704,-2.98],[0.694,-2.99],[0.698,-3],[0.632,-3.244],[0.619,-3.264],[0.308,-3.347],[0.256,-3.297],[0.236,-3.079],[0.242,-3.069],[0.206,-3.027],[0.213,-3.02],[0.203,-3.007],[0.19,-2.796],[0.203,-2.786]],[[2.057,-1.954],[2.284,-2.185],[2.208,-2.479],[2.189,-2.499],[1.951,-2.565],[1.941,-2.558],[1.931,-2.568],[1.892,-2.578],[1.658,-2.35],[1.658,-2.331],[1.737,-2.044],[1.747,-2.034],[1.78,-2.02],[1.803,-2.034],[1.826,-2.011],[1.895,-1.994],[1.915,-1.997],[1.935,-1.984]],[[1.588,-2.42],[1.816,-2.644],[1.819,-2.664],[1.803,-2.726],[1.78,-2.756],[1.79,-2.766],[1.786,-2.792],[1.776,-2.802],[1.78,-2.812],[1.747,-2.937],[1.73,-2.967],[1.423,-3.05],[1.189,-2.815],[1.265,-2.515],[1.275,-2.502]],[[1.117,-2.888],[1.156,-2.918],[1.341,-3.102],[1.351,-3.119],[1.272,-3.422],[1.255,-3.439],[0.952,-3.518],[0.717,-3.287],[0.717,-3.271],[0.787,-3.01],[0.803,-2.97],[0.948,-2.947],[0.975,-2.924]],[[0.645,-3.353],[0.714,-3.413],[0.876,-3.574],[0.879,-3.607],[0.793,-3.904],[0.477,-3.986],[0.308,-3.818],[0.285,-3.591],[0.318,-3.462],[0.341,-3.432]],[[2.232,-2.594],[2.456,-2.822],[2.38,-3.119],[2.364,-3.135],[2.067,-3.218],[1.829,-2.994],[1.826,-2.974],[1.836,-2.934],[1.865,-2.905],[1.862,-2.845],[1.905,-2.697],[1.918,-2.674],[1.938,-2.667],[1.945,-2.674],[1.964,-2.66]],[[1.76,-3.056],[1.806,-3.093],[1.991,-3.284],[1.935,-3.521],[1.908,-3.548],[1.915,-3.597],[1.898,-3.614],[1.856,-3.627],[1.842,-3.62],[1.595,-3.69],[1.367,-3.469],[1.357,-3.449],[1.437,-3.152],[1.453,-3.135]],[[1.291,-3.525],[1.509,-3.739],[1.522,-3.769],[1.443,-4.066],[1.423,-4.082],[1.13,-4.161],[1.1,-4.142],[0.889,-3.927],[0.962,-3.64],[0.968,-3.62],[0.985,-3.604]],[[0.823,-3.996],[1.054,-4.231],[0.975,-4.534],[0.952,-4.554],[0.651,-4.63],[0.421,-4.402],[0.417,-4.386],[0.5,-4.089],[0.516,-4.076]],[[2.403,-3.234],[2.522,-3.36],[2.561,-3.723],[2.555,-3.756],[2.525,-3.785],[2.238,-3.861],[2.011,-3.637],[2.004,-3.607],[2.011,-3.584],[2.024,-3.571],[2.027,-3.525],[2.09,-3.314]],[[1.921,-3.699],[1.945,-3.723],[1.951,-3.719],[2.149,-3.917],[2.159,-3.937],[2.11,-4.125],[2.093,-4.148],[2.096,-4.171],[2.077,-4.237],[2.063,-4.25],[2.02,-4.264],[2.007,-4.254],[1.987,-4.273],[1.945,-4.287],[1.931,-4.283],[1.915,-4.297],[1.766,-4.333],[1.536,-4.109],[1.529,-4.085],[1.605,-3.805],[1.621,-3.779]],[[1.463,-4.168],[1.694,-4.399],[1.694,-4.419],[1.615,-4.706],[1.598,-4.722],[1.295,-4.801],[1.064,-4.574],[1.064,-4.541],[1.14,-4.264],[1.153,-4.25]],[[0.995,-4.64],[1.225,-4.871],[1.153,-5.154],[1.133,-5.191],[0.823,-5.27],[0.592,-5.039],[0.658,-4.765],[0.671,-4.729],[0.688,-4.715]],[[2.571,-3.874],[2.581,-3.884],[2.657,-4.429],[2.641,-4.438],[2.403,-4.498],[2.175,-4.27],[2.255,-3.967],[2.268,-3.953]],[[2.1,-4.343],[2.327,-4.567],[2.331,-4.584],[2.258,-4.857],[2.241,-4.887],[2.212,-4.89],[2.133,-4.92],[2.113,-4.913],[2.09,-4.933],[1.938,-4.973],[1.704,-4.742],[1.704,-4.715],[1.776,-4.452],[1.793,-4.422],[1.931,-4.382],[1.945,-4.386],[1.981,-4.369],[2.007,-4.366],[2.017,-4.376],[2.037,-4.356]],[[1.641,-4.811],[1.869,-5.042],[1.786,-5.349],[1.763,-5.365],[1.466,-5.441],[1.232,-5.204],[1.311,-4.904],[1.331,-4.887],[1.611,-4.811]],[[1.159,-5.276],[1.397,-5.507],[1.397,-5.527],[1.321,-5.804],[1.305,-5.83],[0.998,-5.913],[0.77,-5.689],[0.764,-5.666],[0.84,-5.382],[0.856,-5.359]],[[2.667,-4.534],[2.68,-4.564],[2.769,-5.085],[2.68,-5.115],[2.575,-5.138],[2.347,-4.91],[2.426,-4.607],[2.462,-4.587]],[[2.271,-4.983],[2.502,-5.214],[2.426,-5.51],[2.41,-5.53],[2.354,-5.547],[2.337,-5.543],[2.327,-5.553],[2.251,-5.576],[2.238,-5.567],[2.218,-5.586],[2.172,-5.6],[2.159,-5.596],[2.126,-5.613],[2.103,-5.613],[1.875,-5.375],[1.948,-5.088],[1.964,-5.062],[2.04,-5.039],[2.053,-5.042],[2.106,-5.022],[2.126,-5.032],[2.143,-5.016],[2.222,-4.996],[2.232,-4.999]],[[1.813,-5.451],[2.037,-5.679],[2.04,-5.689],[1.961,-5.989],[1.948,-6.002],[1.641,-6.084],[1.407,-5.854],[1.483,-5.547],[1.496,-5.53],[1.776,-5.454]],[[1.331,-5.92],[1.348,-5.926],[1.562,-6.141],[1.569,-6.17],[1.489,-6.461],[1.479,-6.47],[1.169,-6.553],[0.942,-6.329],[0.935,-6.315],[1.008,-6.038],[1.028,-6.002]],[[2.786,-5.187],[2.796,-5.2],[2.815,-5.319],[2.908,-5.735],[2.895,-5.745],[2.773,-5.778],[2.746,-5.778],[2.525,-5.56],[2.519,-5.543],[2.601,-5.243],[2.634,-5.227]],[[2.446,-5.626],[2.674,-5.85],[2.67,-5.887],[2.601,-6.141],[2.585,-6.17],[2.492,-6.197],[2.482,-6.19],[2.466,-6.203],[2.403,-6.223],[2.383,-6.216],[2.367,-6.233],[2.314,-6.249],[2.307,-6.243],[2.281,-6.256],[2.05,-6.028],[2.05,-5.992],[2.119,-5.735],[2.139,-5.702],[2.238,-5.675],[2.255,-5.685],[2.271,-5.669],[2.35,-5.649],[2.36,-5.656],[2.37,-5.646]],[[2.152,-6.263],[2.152,-6.282],[2.129,-6.299],[1.625,-6.434],[1.611,-6.431],[1.598,-6.414],[1.651,-6.197],[1.667,-6.174],[1.978,-6.091]],[[2.921,-5.84],[2.934,-5.85],[3.027,-6.239],[3.066,-6.378],[3.053,-6.391],[2.944,-6.421],[2.921,-6.421],[2.693,-6.193],[2.773,-5.887],[2.806,-5.87]]],"hexes_front":[[[2.347,-0.846],[2.426,-0.922],[2.423,-1.397],[2.413,-1.41],[2.189,-1.47],[1.954,-1.235],[2.034,-0.938],[2.047,-0.925]],[[2.416,-1.516],[2.423,-1.522],[2.426,-1.925],[2.436,-2.083],[2.413,-2.096],[2.357,-2.106],[2.126,-1.872],[2.208,-1.575],[2.225,-1.562]]],"notch":[[[1.014,-1.133],[1.018,-1.328],[0.988,-1.357],[0.553,-1.357],[0.523,-1.334],[0.52,-1.146],[0.546,-1.113],[0.985,-1.11]]],"notch_block":[[[0.909,-1.39],[0.909,-1.456],[0.899,-1.466],[0.642,-1.466],[0.632,-1.456],[0.635,-1.39],[0.645,-1.381],[0.899,-1.381]],[[0.952,-1.549],[0.942,-1.562],[0.599,-1.562],[0.589,-1.552],[0.625,-1.486],[0.648,-1.47],[0.902,-1.47]]],"vees":[[[2.347,-0.51],[2.331,-0.52],[1.964,-0.421],[1.954,-0.411],[1.964,-0.401],[2.34,-0.401],[2.35,-0.411]],[[1.915,-0.734],[1.921,-0.579],[1.931,-0.569],[2.208,-0.642],[2.228,-0.655],[2.199,-0.671],[1.928,-0.744]]],"above_step":[[[2.782,-2.662],[-0.186,-2.922],[-0.186,0.078],[2.782,0.078]]]},"scaleRefs":["hexmag-series-2-ar15-30.overall_height"],"inputs":{"hexmag-series-2-ar15-30.overall_height":7.366},"tolerance":0.006,"photo":"references/hexmag-series-2-ar15-30 704a55423214 (US D727,456 S (Hexmag, 'Ammunition magazine'), FIG. 2: the side with the catch notch, the magazine's left (the patent's 'right side elevation'), 300 dpi)","method":"luminance < 128, inside [680, 520, 1790, 2835], closing ×3, largest piece, holes filled, inset 2 px (half the outline's stroke); scale from hexmag-series-2-ar15-30.overall_height = 7.366 in (y-extent 2233 px → 303.1 px/in); origin at x min, y max of the outline; Douglas-Peucker at 0.006 in with the extremes kept: 193 points (IoU 0.998 with the full outline); features through the same placement (hexes: the HEXTURE panels of the left side: the cells of the honeycomb this figure draws, 28 of them, each the patent's own closed panel (pieces its shading curves split joined back), cut short where the figure cuts it (at the front strip, the spine and the floorplate); in the order of the lattice's cells (row along the body, then across), .cache/hexmag/hexfield.py: its lattice fitted to the 12 full hexagons' centroids to 0.7 px, spacing 201.0 px, 60.0 degrees; hexes_front: the two panels in the channel down the front of the upper body, under the stripper-clip guides: the lattice's cells there, cut by the channel's lines; notch: the catch's pocket: the rounded rectangle's inside, a stroke's half inside its line; notch_block: under the pocket, the block the figure draws as a trapezoid with a line across it (its two closed parts); vees: the stripper-clip guides at the top of the front: the two wedge-shaped recesses; above_step: above the line where the gripping section steps out of the upper body: the two parallel lines the figure draws across the side (the upper one's middle at row 1395 on column 1160 and row 1436 on column 1650: it falls 0.088 px a pixel toward the spine, 5 degrees), from the front edge's step (columns 960 to 985, rows 1340 to 1380) to the spine, carried past both ends of the outline) (tools/trace.py)","via":"harvest"},"right":{"plane":"xy","origin":"the outline's rearmost point at the top of the feed lips, as the side outline's: the right side as drawn, front to +x","offset":{},"points":[[0,-0.48],[0,-1.809],[0.03,-2.626],[0.063,-3.055],[0.063,-3.101],[0.043,-3.121],[0.04,-3.144],[0.073,-3.187],[0.086,-3.358],[0.066,-3.381],[0.063,-3.408],[0.096,-3.451],[0.112,-3.622],[0.092,-3.642],[0.089,-3.668],[0.122,-3.714],[0.138,-3.886],[0.119,-3.909],[0.119,-3.932],[0.152,-3.975],[0.155,-3.998],[0.171,-4.146],[0.148,-4.186],[0.155,-4.209],[0.181,-4.232],[0.208,-4.407],[0.185,-4.433],[0.185,-4.456],[0.218,-4.496],[0.231,-4.578],[0.241,-4.671],[0.224,-4.69],[0.224,-4.723],[0.257,-4.763],[0.284,-4.928],[0.264,-4.954],[0.264,-4.98],[0.297,-5.017],[0.326,-5.185],[0.31,-5.208],[0.307,-5.234],[0.313,-5.254],[0.343,-5.277],[0.373,-5.429],[0.376,-5.452],[0.356,-5.472],[0.356,-5.505],[0.392,-5.541],[0.425,-5.706],[0.406,-5.736],[0.406,-5.759],[0.442,-5.798],[0.478,-5.97],[0.458,-6.009],[0.465,-6.032],[0.498,-6.062],[0.534,-6.23],[0.514,-6.253],[0.514,-6.276],[0.557,-6.329],[0.594,-6.484],[0.574,-6.51],[0.574,-6.53],[0.58,-6.547],[0.613,-6.573],[0.623,-6.606],[0.656,-6.744],[0.64,-6.761],[0.636,-6.784],[0.643,-6.804],[0.676,-6.83],[0.719,-6.995],[0.702,-7.025],[0.706,-7.051],[0.745,-7.091],[0.778,-7.206],[0.758,-7.246],[0.765,-7.265],[0.801,-7.298],[0.818,-7.354],[0.836,-7.366],[0.879,-7.353],[0.938,-7.359],[2.072,-7.049],[2.155,-7.02],[3.256,-6.726],[3.296,-6.693],[3.352,-6.677],[3.36,-6.642],[3.31,-6.461],[3.259,-6.407],[3.24,-6.407],[3.221,-6.388],[3.231,-6.372],[3.228,-6.349],[3.195,-6.309],[3.159,-6.167],[3.172,-6.138],[3.165,-6.115],[3.139,-6.085],[3.106,-5.947],[3.116,-5.923],[3.113,-5.887],[3.086,-5.864],[3.057,-5.742],[3.05,-5.709],[3.063,-5.693],[3.063,-5.676],[3.033,-5.633],[3.014,-5.548],[3.004,-5.478],[3.014,-5.445],[2.981,-5.389],[2.954,-5.257],[2.968,-5.218],[2.938,-5.172],[2.911,-5.037],[2.925,-4.994],[2.918,-4.971],[2.895,-4.951],[2.869,-4.806],[2.882,-4.76],[2.852,-4.713],[2.836,-4.621],[2.829,-4.562],[2.842,-4.529],[2.813,-4.476],[2.793,-4.347],[2.806,-4.298],[2.78,-4.252],[2.76,-4.113],[2.773,-4.064],[2.75,-4.031],[2.74,-3.975],[2.727,-3.873],[2.74,-3.859],[2.743,-3.83],[2.717,-3.787],[2.7,-3.645],[2.717,-3.602],[2.691,-3.563],[2.687,-3.54],[2.677,-3.404],[2.691,-3.388],[2.691,-3.368],[2.667,-3.338],[2.654,-3.177],[2.667,-3.16],[2.667,-3.127],[2.644,-3.098],[2.631,-2.949],[2.648,-2.93],[2.648,-2.893],[2.625,-2.864],[2.615,-2.686],[2.532,-2.577],[2.536,-0.338],[2.519,-0.298],[2.519,-0.232],[2.076,-0.231],[2.013,-0.228],[1.98,-0.214],[1.957,-0.231],[1.931,-0.201],[1.911,-0.195],[1.902,-0.196],[1.916,-0.209],[1.884,-0.231],[1.861,-0.211],[1.841,-0.231],[1.713,-0.228],[1.683,-0.204],[1.647,-0.208],[1.637,-0.218],[1.624,-0.208],[1.584,-0.208],[1.479,-0.178],[1.377,-0.135],[1.284,-0.082],[1.266,-0.064],[1.278,-0.046],[1.232,-0.049],[1.166,0],[0.186,0],[0.16,-0.013],[0.152,-0.035],[0.148,-0.206],[0.127,-0.228],[0.096,-0.232],[0.092,-0.341],[0.04,-0.404],[0.036,-0.46],[0.015,-0.481]],"features":{"hexes":[[[0.298,-2.076],[0.18,-2.109],[0.18,-2.669],[0.19,-2.695],[0.43,-2.63],[0.453,-2.61],[0.529,-2.316],[0.519,-2.29]],[[1.416,-1.782],[1.403,-1.779],[1.106,-1.858],[1.09,-1.874],[1.011,-2.178],[1.241,-2.409],[1.548,-2.329],[1.561,-2.316],[1.64,-2.006]],[[0.935,-2.247],[0.635,-2.326],[0.615,-2.359],[0.539,-2.643],[0.546,-2.656],[0.773,-2.877],[0.806,-2.874],[1.08,-2.798],[1.093,-2.785],[1.169,-2.508],[1.172,-2.478],[0.951,-2.254]],[[0.473,-2.719],[0.203,-2.785],[0.19,-2.794],[0.203,-3.012],[0.219,-3.029],[0.213,-3.042],[0.239,-3.071],[0.232,-3.081],[0.252,-3.296],[0.298,-3.345],[0.321,-3.345],[0.605,-3.269],[0.622,-3.256],[0.691,-3.005],[0.684,-2.992],[0.704,-2.959],[0.684,-2.939],[0.687,-2.93]],[[2.053,-1.954],[1.937,-1.98],[1.907,-1.996],[1.894,-1.993],[1.832,-2.006],[1.802,-2.029],[1.789,-2.02],[1.752,-2.026],[1.726,-2.056],[1.654,-2.329],[1.654,-2.353],[1.884,-2.58],[1.927,-2.57],[1.937,-2.56],[1.95,-2.564],[2.191,-2.498],[2.204,-2.481],[2.277,-2.217],[2.28,-2.178]],[[1.584,-2.422],[1.551,-2.425],[1.274,-2.501],[1.261,-2.514],[1.182,-2.817],[1.413,-3.052],[1.72,-2.972],[1.736,-2.953],[1.776,-2.811],[1.769,-2.801],[1.782,-2.788],[1.785,-2.768],[1.776,-2.755],[1.795,-2.735],[1.815,-2.656],[1.812,-2.646]],[[1.113,-2.89],[0.974,-2.923],[0.945,-2.949],[0.8,-2.972],[0.79,-2.986],[0.711,-3.269],[0.714,-3.292],[0.951,-3.52],[1.248,-3.441],[1.271,-3.408],[1.347,-3.131],[1.34,-3.111]],[[0.641,-3.355],[0.335,-3.434],[0.318,-3.454],[0.289,-3.559],[0.282,-3.615],[0.305,-3.817],[0.476,-3.985],[0.783,-3.906],[0.803,-3.869],[0.872,-3.619],[0.875,-3.582]],[[2.227,-2.597],[1.97,-2.659],[1.94,-2.676],[1.917,-2.672],[1.901,-2.695],[1.855,-2.854],[1.858,-2.907],[1.832,-2.933],[1.822,-2.972],[1.828,-3.002],[2.056,-3.216],[2.366,-3.137],[2.382,-3.104],[2.442,-2.89],[2.455,-2.821]],[[1.749,-3.058],[1.449,-3.137],[1.429,-3.157],[1.354,-3.447],[1.357,-3.464],[1.591,-3.691],[1.832,-3.629],[1.841,-3.619],[1.855,-3.625],[1.894,-3.612],[1.911,-3.596],[1.904,-3.549],[1.931,-3.523],[1.987,-3.302],[1.983,-3.282],[1.868,-3.17],[1.802,-3.094]],[[1.281,-3.526],[0.978,-3.606],[0.958,-3.638],[0.885,-3.925],[1.113,-4.156],[1.136,-4.156],[1.419,-4.08],[1.436,-4.067],[1.518,-3.76],[1.307,-3.543]],[[0.816,-3.995],[0.757,-4.004],[0.506,-4.074],[0.486,-4.107],[0.414,-4.394],[0.641,-4.624],[0.668,-4.624],[0.958,-4.545],[0.974,-4.516],[1.047,-4.225]],[[2.392,-3.233],[2.089,-3.315],[2.072,-3.345],[2.02,-3.543],[2.023,-3.573],[2.006,-3.589],[2,-3.629],[2.231,-3.856],[2.534,-3.777],[2.547,-3.764],[2.557,-3.695],[2.521,-3.358]],[[1.914,-3.701],[1.617,-3.777],[1.601,-3.797],[1.528,-4.067],[1.528,-4.103],[1.756,-4.328],[1.983,-4.272],[2.003,-4.252],[2.013,-4.262],[2.062,-4.245],[2.076,-4.232],[2.092,-4.176],[2.089,-4.143],[2.105,-4.126],[2.151,-3.958],[2.155,-3.929],[1.947,-3.721],[1.937,-3.724]],[[1.456,-4.166],[1.149,-4.245],[1.133,-4.265],[1.057,-4.568],[1.288,-4.799],[1.594,-4.72],[1.614,-4.694],[1.69,-4.41],[1.687,-4.394]],[[0.994,-4.638],[0.981,-4.634],[0.678,-4.713],[0.658,-4.753],[0.585,-5.033],[0.819,-5.267],[1.126,-5.188],[1.142,-5.172],[1.218,-4.865]],[[2.56,-3.873],[2.267,-3.952],[2.25,-3.968],[2.181,-4.225],[2.178,-4.275],[2.402,-4.496],[2.643,-4.436],[2.656,-4.427],[2.603,-4.09],[2.58,-3.889]],[[2.092,-4.341],[2.033,-4.354],[2.013,-4.374],[2,-4.361],[1.95,-4.374],[1.94,-4.384],[1.927,-4.38],[1.792,-4.417],[1.776,-4.433],[1.696,-4.727],[1.703,-4.746],[1.931,-4.971],[2.089,-4.931],[2.109,-4.911],[2.125,-4.918],[2.201,-4.898],[2.211,-4.888],[2.24,-4.885],[2.254,-4.862],[2.326,-4.591],[2.326,-4.565],[2.161,-4.4]],[[1.624,-4.806],[1.324,-4.885],[1.304,-4.908],[1.228,-5.188],[1.232,-5.215],[1.459,-5.439],[1.766,-5.36],[1.785,-5.337],[1.855,-5.076],[1.858,-5.033],[1.667,-4.839]],[[1.156,-5.274],[0.852,-5.356],[0.836,-5.376],[0.76,-5.679],[0.988,-5.907],[1.014,-5.907],[1.297,-5.831],[1.317,-5.805],[1.393,-5.518],[1.39,-5.501]],[[2.669,-4.532],[2.442,-4.591],[2.428,-4.601],[2.346,-4.895],[2.349,-4.915],[2.58,-5.139],[2.758,-5.093],[2.768,-5.083],[2.679,-4.555]],[[2.264,-4.98],[2.24,-4.987],[2.227,-5],[2.217,-4.994],[2.145,-5.01],[2.122,-5.03],[2.102,-5.02],[1.96,-5.06],[1.947,-5.079],[1.874,-5.343],[1.871,-5.383],[2.102,-5.61],[2.145,-5.604],[2.158,-5.59],[2.171,-5.597],[2.217,-5.584],[2.237,-5.564],[2.247,-5.574],[2.326,-5.551],[2.336,-5.541],[2.349,-5.544],[2.409,-5.528],[2.428,-5.498],[2.494,-5.248],[2.498,-5.205],[2.283,-4.99]],[[1.802,-5.449],[1.492,-5.528],[1.479,-5.541],[1.4,-5.841],[1.403,-5.851],[1.634,-6.082],[1.944,-5.999],[1.96,-5.973],[2.036,-5.693],[2.023,-5.663]],[[1.334,-5.917],[1.027,-5.996],[1.007,-6.022],[0.931,-6.309],[0.938,-6.329],[1.166,-6.553],[1.472,-6.471],[1.485,-6.458],[1.565,-6.164],[1.561,-6.144]],[[2.785,-5.188],[2.616,-5.231],[2.593,-5.248],[2.517,-5.538],[2.521,-5.554],[2.735,-5.768],[2.755,-5.778],[2.893,-5.742],[2.903,-5.732],[2.827,-5.389],[2.794,-5.205]],[[2.445,-5.623],[2.369,-5.64],[2.359,-5.65],[2.28,-5.663],[2.254,-5.683],[2.234,-5.673],[2.191,-5.683],[2.178,-5.696],[2.168,-5.689],[2.135,-5.699],[2.118,-5.719],[2.049,-5.983],[2.046,-6.026],[2.283,-6.256],[2.306,-6.243],[2.32,-6.247],[2.362,-6.233],[2.382,-6.214],[2.392,-6.224],[2.471,-6.2],[2.481,-6.191],[2.491,-6.194],[2.583,-6.167],[2.597,-6.144],[2.676,-5.858],[2.669,-5.844]],[[2.151,-6.27],[1.983,-6.095],[1.954,-6.092],[1.663,-6.171],[1.647,-6.2],[1.594,-6.411],[1.611,-6.431],[2.132,-6.296]],[[2.92,-5.838],[2.781,-5.874],[2.771,-5.884],[2.689,-6.187],[2.91,-6.415],[2.93,-6.421],[3.052,-6.388],[3.058,-6.372],[2.933,-5.848]]],"hexes_front":[[[2.349,-0.846],[2.046,-0.925],[2.033,-0.941],[1.96,-1.205],[1.957,-1.245],[2.188,-1.469],[2.422,-1.403],[2.428,-0.922]],[[2.415,-1.512],[2.217,-1.565],[2.207,-1.574],[2.125,-1.871],[2.359,-2.109],[2.435,-2.085],[2.425,-1.835],[2.425,-1.551]]],"vees":[[[1.96,-0.414],[1.97,-0.424],[2.329,-0.519],[2.349,-0.509],[2.353,-0.414],[2.343,-0.404],[1.97,-0.404]],[[1.914,-0.734],[1.931,-0.744],[2.211,-0.668],[2.231,-0.654],[2.221,-0.645],[1.931,-0.569],[1.921,-0.579]]],"name_block":[[[0.434,-0.457],[0.427,-0.476],[0.427,-0.958],[0.434,-0.974],[0.467,-1.004],[1.548,-1.007],[1.571,-0.994],[1.594,-0.964],[1.598,-0.483],[1.588,-0.457],[1.558,-0.43],[1.528,-0.424],[0.486,-0.424],[0.46,-0.43]]]},"scaleRefs":["hexmag-series-2-ar15-30.overall_height"],"inputs":{"hexmag-series-2-ar15-30.overall_height":7.366},"tolerance":0.006,"photo":"references/hexmag-series-2-ar15-30 c27816f73eea (US D727,456 S (Hexmag), FIG. 3: the other side, the magazine's right (the patent's 'left side elevation'), its name block and its HEXTURE panels, 300 dpi)","method":"luminance < 128, inside [680, 520, 1790, 2835], closing ×3, largest piece, holes filled, inset 2 px (half the outline's stroke); scale from hexmag-series-2-ar15-30.overall_height = 7.366 in (y-extent 2234 px → 303.3 px/in); origin at x min, y max of the outline; Douglas-Peucker at 0.006 in with the extremes kept: 193 points (IoU 0.998 with the full outline); features through the same placement (hexes: the HEXTURE panels of the right side: the cells of the honeycomb this figure draws, 28 of them, each the patent's own closed panel (pieces its shading curves split joined back), cut short where the figure cuts it (at the front strip, the spine and the floorplate); in the order of the lattice's cells (row along the body, then across), .cache/hexmag/hexfield.py: its lattice fitted to the 12 full hexagons' centroids to 0.8 px, spacing 200.9 px, 60.0 degrees; hexes_front: the two panels in the channel down the front of the upper body, under the stripper-clip guides: the lattice's cells there, cut by the channel's lines; vees: the stripper-clip guides at the top of the front: the two wedge-shaped recesses; name_block: the name block: the rounded rectangle near the top of the rear, the line's middle (on the Series 2 it carries \"HX-AR SERIES 2 / PATENT D727,456 S / HEXMAG / MADE IN THE USA\": Primary Arms' photo f9da4bea084e)) (tools/trace.py)","via":"harvest"},"rear":{"plane":"zy","origin":"the middle of the outline across, at the top of the feed lips","offset":{},"points":[[-0.542,-6.685],[-0.542,-7.252],[-0.526,-7.289],[-0.495,-7.31],[-0.406,-7.33],[-0.336,-7.336],[-0.31,-7.353],[-0.267,-7.359],[-0.211,-7.353],[-0.148,-7.363],[-0.109,-7.359],[0.036,-7.366],[0.109,-7.359],[0.142,-7.363],[0.208,-7.353],[0.257,-7.359],[0.31,-7.353],[0.336,-7.336],[0.458,-7.32],[0.519,-7.295],[0.542,-7.249],[0.542,-6.698],[0.509,-6.636],[0.467,-6.596],[0.463,-6.533],[0.467,-2.824],[0.463,-2.785],[0.437,-2.745],[0.44,-0.203],[0.424,-0.137],[0.394,-0.087],[0.369,-0.059],[0.31,-0.02],[0.257,-0.003],[0.224,0],[0.226,-0.031],[0.208,-0.049],[0.148,-0.043],[0.134,-0.054],[0.171,-0.056],[0.188,-0.073],[0.208,-0.056],[0.226,-0.074],[0.226,-0.163],[0.213,-0.176],[0.223,-0.186],[0.223,-0.203],[0.204,-0.221],[0.188,-0.204],[0.181,-0.211],[0.162,-0.208],[0.142,-0.228],[0.115,-0.208],[0.079,-0.208],[0.084,-0.219],[0.066,-0.237],[0.049,-0.237],[0.028,-0.216],[0.033,-0.208],[0,-0.208],[-0.016,-0.191],[-0.049,-0.228],[-0.129,-0.224],[-0.158,-0.241],[-0.175,-0.224],[-0.201,-0.228],[-0.219,-0.209],[-0.223,-0.002],[-0.244,0],[-0.277,-0.007],[-0.333,-0.03],[-0.384,-0.071],[-0.424,-0.134],[-0.437,-0.173],[-0.443,-0.223],[-0.443,-2.709],[-0.447,-2.745],[-0.47,-2.781],[-0.473,-2.831],[-0.473,-6.596],[-0.513,-6.632]],"scaleRefs":["hexmag-series-2-ar15-30.overall_height"],"inputs":{"hexmag-series-2-ar15-30.overall_height":7.366},"tolerance":0.004,"photo":"references/hexmag-series-2-ar15-30 533d2a4dcb87 (US D727,456 S (Hexmag), FIG. 4: the rear elevation (the magazine's left on the viewer's left), 300 dpi)","method":"luminance < 128, inside [1030, 470, 1400, 2760], 1 boxes excluded, closing ×3, largest piece, holes filled, inset 2 px (half the outline's stroke); scale from hexmag-series-2-ar15-30.overall_height = 7.366 in (y-extent 2234 px → 303.3 px/in); origin at x center, y max of the outline; Douglas-Peucker at 0.004 in with the extremes kept: 81 points (IoU 0.997 with the full outline) (tools/trace.py)","via":"harvest"}},"gaps":[{"what":"A square view of the Series 2 from its rear or its front, and a figure of its own that fixes the scale: the patent's rear elevation (2013) is the section, and the scale is the well's (the top section reaching the well's front wall from the catalog's seat), not a reading of the magazine","need":"A photograph of HX30-AR15S2 end on, or Hexmag's own drawing"},{"what":"How far the HEXTURE panels stand out of their grooves, how deep the stripper-clip guides and the HexID's pocket are (assumed 0.03, 0.04 and 0.05 in)","need":"A view along a side from close by with a panel's edge in profile, or Hexmag's figure"},{"what":"What Hexmag's 7.5, 2.66 and 1.125 in are of: at the scale the well gives (7.366 tall) the floorplate is 1.085 wide and about 2.65 long along its own lean, and the top section 2.53 from the spine to the front","need":"Hexmag's drawing, or a seller's table of the magazine's sizes with what each spans"},{"what":"The gray's colour: the two photographs of HX30-AR15S2-GRY on file read 33 levels apart on the same flat (Blackstone's slate #5d6169, AmmunitionStore's charcoal #3c413a); Hexmag's gallery has the black one only","need":"Hexmag's own photograph of the gray one, or one of it beside a black or an FDE one under one light"},{"what":"The block under the catch window (not drawn): the rear elevation has it 0.049 in out of a side that is as wide as a well already","need":"A view of the Series 2 from its front or rear with the left side in profile at the window"}]},"holosun-aro-163-mount":{"id":"holosun-aro-163-mount","name":"1.63 in lower 1/3 co-witness pedestal mount (HS-MOUNT-AR-RISER-ARO)","manufacturer":"Holosun","sku":"HS-MOUNT-AR-RISER-ARO","url":"https://www.holosun.eu/p/70195767","category":"optic_mount","description":"The pedestal Holosun sells the ARO on: \"an all-new 1.63\" lower 1/3 co-witness pedestal mount\" (its manual). A Micro-footprint dot screws to its deck (Holosun's EU shop, of it sold alone: \"Footprint (upper): Aimpoint Micro\", \"compatible with HOLOSUN Micros ARO-CORE\"); the ARO on it has its axis 1.63 in over the rail (\"Central Mount Height 1.63\"\", Holosun's page), a lower 1/3 co-witness. Its clamp holds the rail by one cross bolt: \"Apply forward pressure to the ARO and tighten the mounting clamp screw 30INCH/lbs.\" (the manual). The page linked is Holosun's EU shop's for it alone, priced in euros: no US seller on file sells it apart from the sight.","weight":"holosun-aro-163-mount.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":[0,0,0],"note":"Mount frame: origin on the rail's top under the clamp's middle, +x forward: where the pair's part had it. The clamp is drawn about its cross bolt, 0.01 in ahead of it (holosun-aro.cross_bolt_x)."},"deck":{"origin":["{.deck_x}","{.deck_above_rail}",0],"note":"On the deck at the footprint's middle, over the stem: where a Micro dot's base is put (D101)."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":"={.mount_length} / 2","clamp_front":"={.mount_length} / 2"},"flips":false,"note":"The clamp's length about its middle (the frame's origin)."},"deck":{"type":"optic_footprint","role":"deck","anchor":"deck","params":{"pattern":"aimpoint_micro"},"flips":false,"note":"Holosun's EU shop, of the mount sold alone: \"Footprint (upper): Aimpoint Micro\"; of the ARO: \"Footprint: Aimpoint Micro\", and Holosun's US page \"Optic Footprint T1 / T2\" (data/interfaces.yaml, optic_footprint)."}},"materials":{"mount":{"label":"Mount","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","sheen":"satin","note":"The 1.63 in pedestal mount the sight ships on (Holosun's page: \"MAO finished aluminum construction with IP67 water resistance and includes 1.63 inch lower 1/3 mount and 1.05 inch low mount for multiple rifle setups\"): black in every photo, a smoother skin than the housing's (no grain shows on its faces in Holosun's EU side view, where the housing's is speckled; its flats read #262626 to #3e3e3e). No page on file says what it is finished in: drawn as the housing's finish a step smoother. Its cross bolt and hex nut are dark steel (the bolt's end reads #4e4e4e, a grey a little lighter than the mount) and are part of this slot, drawn as themselves since 2026-10-13 (the nut a hexagon on the right jaw, the bolt's head a round on the left): a steel grey of their own would need a slot the part doesn't have. Holosun's EU shop sells it alone in black (HS-MOUNT-AR-RISER-ARO); its list of accessories names a riser in FDE, HS-MOUNT-AR-RISER-FDE, with no page of its own on file: not offered."}},"components":{},"geometry":{"model":"holosun-aro-163-mount.glb","components":{},"approximations":["Built piece by piece from the ledger of the pair (2026-10-13, the second pass): its clamp 1.49 in long about the cross bolt, each jaw's upright face tallest at the bolt and falling to its two ends, a sloped facet over it up to the clamp's top, the four upright corners broken; the stem a middle stretch at its full width with its sides turned in to two narrower ends and a flare round its foot, up to the deck; the nut in a pocket in the right jaw's face, the bolt's round head on the left. Lengths and heights through Holosun's two side photos' cameras, widths off the user's straight rear view.","Its deck is drawn as the stem's flat top: Holosun's pictures of it alone show a plate as long as the sight's base with a lip along each long edge, four screw holes and a recoil key, which the sight's base covers when the two are together; not drawn (D102: a deck is drawn flat at its floor with nothing above it where a dot stands).","Assumed, because no view on file shows them: how deep the nut's pocket is (0.08 in), how wide the stem's two ends are (half the stem), the stem's flare and the corners' breaks at 45 degrees, the right jaw's facet the same as the left's, the clamp's top level across and its fall to each end straight.","The rail's place under it is the rail's own head in section (MIL-STD-1913's) from the rail's top down to the lower gauge line, the clamp's length; below that line the jaws are the end view's, less what stood inside a rail's lower faces; how far they hook isn't sourced."],"ledger":["holosun-aro-163-mount.deck_above_rail","holosun-aro-163-mount.mount_length","holosun-aro-163-mount.clamp_below_rail","holosun-aro.stem_width","holosun-aro.stem_length"]},"profiles":{},"gaps":[{"what":"The clamp's two ends: drawn as one surface falling straight to each end. The side photos show a dark round-ended notch in it at each end, the two obliques a pocket stepped down into its middle, and Holosun's front and rear views a dark face nearly the clamp's width with a lighter ledge under it over the rail. The lug under the clamp's roof and the two slits down from the nut's pocket aren't drawn either.","need":"A camera fitted to Holosun's front and rear views or to one of the two obliques on file; or a view of the mount from straight above."},{"what":"The deck plate: its lips, its four holes and its recoil key","need":"A straight view of the mount alone from the side and from above; Holosun's two pictures of it alone are from above and a quarter"},{"what":"The 1.05 in low mount the ARO comes with (Holosun's page: \"Included Mounts 1.63\" Mount 1.05\" Mount\")","need":"Any photograph of it, alone or with the sight on it: none is on file, so it isn't a part (D102)"},{"what":"The clamp's heights: the two side photos' cameras have each jaw's face 0.197 in over the rail at the bolt and the clamp's top 0.28; the user's rear view has 0.243 and 0.35. Drawn at the first.","need":"A straight view of the mount from the side with the rail in it."},{"what":"The cross bolt's height: Holosun's two side photos have its axis at the rail's top (0.015 in over it), the user's rear view 0.08 over it. Drawn at the first.","need":"A straight view of the mount from the side or from behind with the rail in it."}]},"holosun-aro":{"id":"holosun-aro","name":"ARO 2 MOA red dot (listed by Holosun as ARO-CORE-RD-2)","manufacturer":"Holosun","category":"optic","weight":"holosun-aro.weight_body","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"footprint":{"origin":[0,0,0],"note":"Optic frame: origin on the sight's base, its seam with the pedestal's deck, at the footprint's middle (taken to be over the pedestal's stem: holosun-aro-163-mount.deck_x), +x forward (D101)."},"optical_axis":{"origin":[0,"{.axis_above_base}",0]}},"interfaces":{"footprint":{"type":"optic_footprint","role":"base","anchor":"footprint","params":{"pattern":"aimpoint_micro"},"flips":false,"note":"Holosun's page: \"Optic Footprint T1 / T2\"; its EU shop: \"Footprint: Aimpoint Micro\", \"Footprint (supplied mounting plate): Picatinny\" (data/interfaces.yaml, optic_footprint)."},"sight_line":{"type":"optic.sight_line","role":"sight","params":{"magnification":"1x"},"flips":false,"note":"Holosun's page: \"Magnification 1x\", \"Unlimited Eye Relief Yes\". The eye can be anywhere behind it, so it has no eye point of its own."}},"materials":{"body":{"label":"Housing","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized_matte","color":"placeholder-black","sku":"ARO-CORE-RD-2","source":"https://www.holosun.com/products/aro-core-rd-2"}},"default":"black","note":"Black is the one colour it is sold in. Holosun's page: \"Housing Material Aluminum\", \"Surface Finish MAO\", \"Housing Color Black\" (its EU shop: \"Housing Color: black\", \"Surface finish: MAO\"); sellers list the same sight as ARO-RD2 (Alquist Arms, UPC 810047073598, \"Black\"). MAO is a micro-arc oxide coat, matte and finely grained in Holosun's photos (its EU side views read #3d3d3d to #505050 on the housing's flats, a lit black): drawn as matte anodize, and a black isn't fitted to a photo. The two turret caps are the housing's own tone in those photos and are the housing here. Drawn since 2026-10-13 and in this slot, being black as the housing is: the pad of the + and - buttons on top (rubber, smoother than the housing's skin in Holosun's photos: a look of its own that no slot here carries), the battery tray's cover and its two black Torx screws on the right side."},"lens":{"label":"Lenses","finish":"glass","recolorable":false,"color":"glass-clear"}},"components":{"body":{"label":"Housing","material":"body"},"lens":{"label":"Lenses","material":"lens"}},"geometry":{"model":"holosun-aro.glb","components":{},"approximations":["The housing is built piece by piece from the ledger (2026-10-13): a round body between the two bezels, the objective's tube and the eyepiece's bezel, a block under it whose flat upright flanks run down to the base, the raised deck along the top with the buttons' pad and its two buttons, the elevation cap on the deck and the windage cap on its boss out of the right side, the battery tray's cover on the right flank with its two screws' heads. Most of it is read through a camera fitted to each of Holosun's two side photos, which are taken from 20 degrees above (the ledger's note); what lies across the sight is from the user's straight rear view.","Its footprint's middle is taken to be over the pedestal's stem, which stands over its cross bolt: no view shows the screws that hold the sight to it. Its base is the pedestal's deck, the plane its skirt's chamfered foot comes down to (the axis 0.902 in over it, Holosun's .9).","Assumed, 0.02 in each, because no view shows them in profile: how deep the long flute high on each flank, the HOLOSUN panels' ovals and the grooves round the two buttons are sunk, how far the screws' heads and the bolt's head stand, and the breaks of the edges. Assumed too: the windage turret's boss a plain cylinder, one round for the cover's four corners, the pad's corners as round as its margin beside a button, the deck's front and rear slopes run to the round body's own edges, each coin slot as deep as it is wide, the flutes' ends square (they are rounded).","Not drawn: the raised panel on the left flank and the two small pads beside the HOLOSUN panel on that side, the bead between each flank and the round body, the rings cut in the two caps, the screws' sockets, the lettering and the logo's glyphs.","The glass is drawn at the end faces: the objective's at Holosun's 22 mm (0.866 in; its front photo reads 0.85), the rear window at the clear circle measured from behind (0.737). Both really sit down a bore, whose depth isn't sourced."],"ledger":["holosun-aro.length","holosun-aro.width","holosun-aro.height","holosun-aro.axis_above_base","holosun-aro.window"]},"profiles":{"side":{"plane":"xy","origin":"the clamp's middle (x over its rows), the clamp's bottom; offset to the rail top","offset":{"y":"clamp_bottom_y"},"points":[[-1.117,2.048],[-1.101,1.339],[-1.012,1.326],[-0.761,0.887],[-0.454,0.882],[-0.457,0.763],[-0.651,0.697],[-0.706,0.648],[-0.702,0.408],[-0.64,0.402],[-0.721,0.355],[-0.72,0.03],[-0.424,0],[0,0],[0.418,0.002],[0.716,0.032],[0.716,0.357],[0.625,0.406],[0.669,0.414],[0.673,0.652],[0.608,0.701],[0.443,0.76],[0.443,0.886],[0.771,0.891],[1.005,1.294],[1.292,1.3],[1.312,1.343],[1.328,1.473],[1.339,1.779],[1.328,2.25],[1.31,2.379],[1.288,2.421],[1.005,2.423],[0.92,2.545],[-0.316,2.613],[-0.523,2.655],[-0.69,2.648],[-0.902,2.604],[-1.01,2.393],[-1.101,2.378]],"scaleRefs":["holosun-aro.length","holosun-aro.height"],"inputs":{"holosun-aro.height":2.63,"holosun-aro.length":2.48},"tolerance":0.01,"photo":"references/holosun-aro 3233645ac025 (Holosun EU true side view, ARO-RD2 on its 1.63 in mount, plain side (objective to the left))","method":"luminance < 200, closing ×2, largest piece, holes filled; scale from holosun-aro.length = 2.48 in (x-extent 1268 px → 511.3 px/in) and holosun-aro.height = 2.63 in (y-extent 1371 px → 521.3 px/in), which agree within 2.0%; mean 516.3 px/in; origin at x center, y min of the outline (x over 0.9–1.0 of the height from the top); Douglas-Peucker at 0.01 in with the extremes kept: 40 points (IoU 0.994 with the full outline) (tools/trace.py)","via":"harvest","note":"Buttons, caps and markings are M5 detail."},"front":{"plane":"zy","origin":"the optical axis's vertical (z 0, over the rail's centre) at the rail top","offset":{},"points":[[-0.596,1.706],[-0.596,1.566],[-0.544,1.381],[-0.463,1.255],[-0.53,1.196],[-0.53,0.79],[-0.43,0.683],[-0.134,0.661],[-0.116,0.642],[-0.116,0.376],[-0.134,0.358],[-0.415,0.35],[-0.467,0.291],[-0.504,0.291],[-0.559,0.243],[-0.567,-0.141],[-0.544,-0.171],[-0.552,-0.185],[-0.489,-0.241],[-0.349,-0.241],[-0.33,-0.222],[-0.308,-0.06],[-0.29,-0.041],[-0.238,-0.034],[-0.149,-0.034],[-0.112,-0.071],[0.161,-0.071],[0.205,-0.034],[0.294,-0.027],[0.342,-0.052],[0.313,-0.082],[0.305,-0.163],[0.324,-0.182],[0.494,-0.174],[0.53,-0.226],[0.582,-0.204],[0.641,-0.137],[0.819,-0.145],[0.867,-0.097],[0.867,-0.03],[0.9,0.003],[0.922,-0.012],[0.94,0.014],[0.94,0.169],[0.929,0.195],[0.885,0.195],[0.867,0.214],[0.848,0.299],[0.811,0.254],[0.663,0.254],[0.627,0.299],[0.604,0.284],[0.464,0.365],[0.176,0.358],[0.157,0.376],[0.157,0.649],[0.176,0.668],[0.464,0.69],[0.564,0.812],[0.564,0.96],[0.593,0.997],[0.586,1.13],[0.615,1.196],[0.608,1.226],[0.549,1.277],[0.627,1.311],[0.745,1.325],[0.793,1.366],[0.8,1.795],[0.793,1.913],[0.759,1.968],[0.737,1.917],[0.538,1.939],[0.364,2.12],[0.32,2.393],[0.264,2.434],[0.146,2.434],[0.095,2.404],[-0.098,2.404],[-0.12,2.426],[-0.245,2.426],[-0.29,2.419],[-0.33,2.386],[-0.375,2.105],[-0.5,1.965],[-0.574,1.817]],"scaleRefs":["holosun-aro.optical_axis_above_rail","holosun-aro.clamp_below_rail","holosun-aro.top_above_rail","holosun-aro.mount_rise"],"inputs":{"holosun-aro.clamp_below_rail":0.227,"holosun-aro.mount_rise":0.728,"holosun-aro.optical_axis_above_rail":1.63,"holosun-aro.top_above_rail":2.41},"tolerance":0.01,"photo":"references/holosun-aro 33a02158eb43 (ARO-RD2 end view from the rear, on white; supplied in chat)","method":"luminance < 200, closing ×2, largest piece, holes filled; frame from the reviewed holes axis, rail, clamp, top, base (135.4 px/in, rms 0.013 in over 5 points); origin at the photo's frame; Douglas-Peucker at 0.01 in with the extremes kept: 86 points (IoU 0.993 with the full outline); checks: width 1.537 ± 0.024 in vs holosun-aro.width 1.54 ± 0 (confirmed): agrees (tools/trace.py)","via":"user"}},"gaps":[{"what":"How deep the flutes, the HOLOSUN panels and the buttons' grooves are sunk, and how far the cover, its screws' heads and the caps stand: drawn at 0.02 in or at what the rear view's outline has, none of them seen in profile.","need":"A camera fitted to one of the two obliques on file (5ec56fffa262 at 2200 px, d968cfc95219), which show them from a quarter; or a view from above."},{"what":"The left flank's raised panel and the two small pads beside the HOLOSUN panel on that side, in Holosun's left photo (3233645ac025): not drawn.","need":"Their outlines read through that photo's camera, and how far they stand from a view that shows it."},{"what":"Whether the round body is wider than the objective's bezel: the rear view has one circle for both (1.20 in), the side photos have the bezel at 1.17.","need":"A straight view from the front, or from above."}]},"holosun-eps-carry":{"id":"holosun-eps-carry","name":"EPS Carry enclosed pistol sight, 2 MOA red dot (EPS-CARRY-RD-2)","manufacturer":"Holosun","sku":"EPS-CARRY-RD-2","url":"https://www.holosun.com/products/eps-carry-rd-2","category":"optic","description":"Holosun's EPS Carry, an enclosed 1x reflex sight for subcompact carry pistols: a sealed 7075 aluminium hood over a 0.77 by 0.58 in window, the + and - buttons on its left side, a CR1620 battery in a tray on its right, and a deck behind the hood with its two screws and its elevation adjuster. It screws to a slide by Holosun's K footprint, and comes with an RMSc-to-K adapter plate (holosun.com: \"Direct K footprint mounting with included RMSc to K adapter plate expands compatibility across many popular subcompact carry pistols.\").","weight":"holosun-eps-carry.weight","fitments":{"label":"Mounted","default":"direct","setup":true,"says":"Holosun: \"Direct K footprint mounting with included RMSc to K adapter plate expands compatibility across many popular subcompact carry pistols.\"","options":{"direct":{"label":"Direct (K footprint)","params":{},"source":"https://www.holosun.com/products/eps-carry-rd-2"},"plate":{"label":"On its RMSc plate","params":{"footprint":{"pattern":"shield_rmsc"}},"anchors":{"footprint":{"origin":["{.plate_offset_x}","-{.plate_thickness}",0],"note":"On the plate: the plate's underside at the RMSc pattern's middle, the plate's 3 mm (Holosun EU: \"Size: 45x25x3\") under the sight's base, the pattern's middle assumed over the sight's screws (plate_offset_x)."}},"components":{"sight":"plated"},"source":"https://www.holosun.com/products/eps-carry-rd-2"}}},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"footprint":{"origin":[0,0,0],"note":"Optic frame: origin on the sight's flat underside midway between its two screw holes (the footprint's middle, where a slide's deck states its own: taurus-tx22-toro-slide's `deck`), +x forward (D101)."},"optical_axis":{"origin":[0,"{.axis_above_base}",0]}},"interfaces":{"footprint":{"type":"optic_footprint","role":"base","anchor":"footprint","params":{"pattern":"holosun_k"},"flips":false,"note":"Holosun's US page (EPS-CARRY-RD-2, 2026-11-06): \"Fitment Direct Mount K Footprint Included Adapter Plate RMSc to K Footprint\", and \"K Footprint Compatibility Direct K footprint mounting with included RMSc to K adapter plate expands compatibility across many popular subcompact carry pistols.\"; its EU shop: \"Footprint: Holosun-K Footprint (supplied mounting plate): RMSc\", and \"EPS/EPS Carry optics have an extended K-Footprint (4 additional holes) and are fully backward compatible with older accessories, but new EPS/EPS Carry accessories are not always compatible with older Holosun-K optics\". Primary Arms: \"Holosun K series mounting footprint Includes Shield RMSc adapter plate\", \"Mount Compatibility Holosun 407K/507K, Shield RMSc\"; AT3 Tactical: \"The Holosun EPS uses the Holosun K footprint similar to the Shield RMSc cut but with some small differences.\" The pattern's name `holosun_k` is proposed (no part on file states it); on a Shield RMSc cut it goes by the plate in its box (data/interfaces.yaml, optic_footprint)."},"sight_line":{"type":"optic.sight_line","role":"sight","params":{"magnification":"1x"},"flips":false,"note":"Holosun's page: \"Magnification 1x\", \"Unlimited Eye Relief Yes\": a red dot, the eye anywhere behind it, so it has no eye point of its own."}},"materials":{"body":{"label":"Housing","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized_matte","color":"placeholder-black","sku":"EPS-CARRY-RD-2","source":"https://www.holosun.com/products/eps-carry-rd-2"}},"default":"black","note":"Black is the one housing Holosun sells it in. Its page: \"Housing Material 7075 T6 Aluminum\", \"Surface Finish Anodized\", \"Housing Color Black\" (the launch release: \"7075-aluminum black anodized housing\"; its EU shop: \"Housing Color: black\"). In the EU shop's photos of the red 2 MOA item a fine-grained matte black, lit to a dark grey on its flats: drawn as matte anodize, and a black isn't fitted to a photo. The other items are this housing with another reticle (holosun.com: EPS-CARRY-RD-6, EPS-CARRY-RD-MRS, EPS-CARRY-GR-2, -GR-6, -GR-MRS, the RONIN-EPS-CARRY-RD-MRS and -GR-MRS editions; the EU shop also EPS-CARRY-GD-2 and -GD-6): sold, and not offered here, since what tells them apart is the dot and not the look. The RONIN editions' look isn't on file."},"tray":{"label":"Battery tray","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","note":"The battery tray's cover on the right side, with its slotted screw (Holosun: \"Side Loading Battery Tray CR1620 side tray design allows battery replacement without removing the optic from the slide\"). As black as the housing round it in the right side photo (516b35e9e5a7: #313131 on its lower part against #323232 on the flank above it, the medians of a region of each)."},"pad":{"label":"Buttons' pad","finish":"rubber","recolorable":false,"color":"placeholder-polymer-black","note":"The pad on the left side with the + and - buttons, each in a ring. Smoother and a little blacker than the housing's grain in the left side photo (75b98ec314e3: #383838 between the buttons against #3f3f3f on the flank over the pad and #393939 on the base, the medians of a region of each); no page says what it is: drawn as rubber, as the HS510C's pad is."},"screws":{"label":"Adjusters and the tray's screw","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The elevation adjuster on the deck, the windage adjuster in the base's right side and the tray cover's slotted screw: dark steel, each with its slot, in the side and rear photos."},"plate":{"label":"RMSc plate","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","note":"The RMSc-to-K adapter plate in the box (holosun.com: \"In The Box EPS-CARRY-RD-2 ‍ RMSc To K Adapter Plate\"), drawn only with the sight set up on it (the fitment `plate`). Holosun's EU shop, of the plate it sells alone: \"Material: aluminium Housing Color: black\"; a matte black in its two photos (6c35fcf048d5, ba2287d3c746), drawn as matte anodize."},"lens":{"label":"Lenses","finish":"glass","recolorable":false,"color":"glass-clear","note":"The objective glass at the front (coated: orange from ahead in the obliques, 4790d62219c9) and the window at the rear (blue-green from behind, 1f3739adf780). The coatings aren't a colour of the glass here."}},"components":{},"geometry":{"components":{"sight":"holosun-eps-carry.sight.glb","plated":"holosun-eps-carry.plated.glb"},"approximations":["The housing is the hull of Holosun's dimensioned drawing (its left side view and its end view from the front, the tray's cover left out of the end view), so its section is the end view's all along the hood and the base: the hood's rounded top edges, its flanks, its front face leaning back (the side view), its rear top corner's chamfer and its rear face running into the deck by a round, the deck and the lip across its rear end.","The window is a straight tunnel of Holosun's 0.77 by 0.58 in through the hood, its corners the drawing's, from the rear face to the front; a glass at each end, set back from its face (assumed: glass_inset, glass_thickness) and leaning with the front face at the front. Round each, a bezel sunk a groove's depth: the drawing's outer window line at the front, its top arched, and the same at the rear (the rear face isn't drawn: the rear photo frames that window the same way).","The deck: two counterbored screw holes, through, a screw spacing apart about the frame's origin (the underside photo), the counterbores (the left photo's size, an assumed depth) biting into the hood's rear round as the obliques show; the elevation adjuster's slotted head in its ring on the deck, in a scallop of the lip; the lip's two corner facets as one plane each, through the lip's top a facet's depth in from the flank, the flank a facet's depth down at the rear face, and the flank at the deck where the drawing's wedge ends.","Under the base: the two small pockets beside the screws and the four round pockets across the front (the EU shop's \"4 additional holes\"), at the underside photo's places, an assumed depth.","The left flank: the buttons' pad (rubber) standing the drawing's 0.008, its front edge leaning with the face; each button a ring groove round its face and its + or - standing half a groove; the right flank: the battery tray's cover, its wide lower part and the stem round its slotted screw, standing the drawing's 0.062 (its lengths from the right photo), the windage adjuster's slotted head in its ring in the base; the HOLOSUN panels, on the right flank and across the top near the front, standing a groove's depth.","The RMSc plate (the plated model only): Holosun's EU table's 45 x 25 x 3 mm, its corners rounded and its short ends arched as its two photos show them; its two holes for the sight's screws and its four corner holes. Assumed (the ledger's plate_* entries): its place under the sight (centred under the base), the RMSc pattern's middle over the K pattern's, the holes' size and place, the corners' round, the ends' arch. Its bosses stand in the sight's own pockets and aren't drawn.","Not drawn: the lettering (HOLOSUN in its panels, the serial, the adjusters' arrows and letters), the screws' Torx sockets, the sealed T-shaped cover and the rectangular panel under the base, the lines the drawing has along the hood's foot (0.24 to 0.30 in up: a step between the hood's 0.988 and the base's 0.999, under a pixel at the page's size), and the glass's coatings."],"ledger":["holosun-eps-carry.length","holosun-eps-carry.width","holosun-eps-carry.height","holosun-eps-carry.axis_above_base","holosun-eps-carry.window_width","holosun-eps-carry.window_height"]},"profiles":{"side":{"plane":"xy","origin":"the base's rear face, its foot (the underside)","offset":{"x":"rear_x"},"points":[[0,0.238],[0.001,0],[1.597,0],[1.611,0.014],[1.611,0.211],[1.588,0.23],[1.569,0.294],[1.5,0.606],[1.471,0.764],[1.471,0.801],[1.482,0.824],[1.482,0.845],[1.463,0.934],[1.452,0.95],[0.678,0.95],[0.666,0.943],[0.649,0.948],[0.641,0.937],[0.6,0.927],[0.59,0.915],[0.574,0.371],[0.567,0.327],[0.536,0.28],[0.512,0.26],[0.479,0.247],[0.242,0.245],[0.213,0.254],[0.195,0.271],[0.186,0.293],[0.011,0.293],[0.002,0.284]],"scaleRefs":["holosun-eps-carry.length","holosun-eps-carry.height"],"inputs":{"holosun-eps-carry.height":0.95,"holosun-eps-carry.length":1.61},"tolerance":0.004,"photo":"references/holosun-eps-carry 169abca1c98b (Holosun EU, the EPS Carry's dimensioned drawing, the side view (the left side, front to the left))","method":"luminance < 200, inside [1070, 752, 1866, 1232], closing ×2, largest piece, holes filled, opening after the fill 7 px ×1, inset 1 px (half the outline's stroke); scale from holosun-eps-carry.length = 1.61 in (x-extent 775 px → 481.4 px/in) and holosun-eps-carry.height = 0.95 in (y-extent 457 px → 481.1 px/in), which agree within 0.1%; mean 481.2 px/in; origin at x min, y min of the outline; Douglas-Peucker at 0.004 in with the extremes kept: 31 points (IoU 0.998 with the full outline) (tools/trace.py)","via":"harvest","note":"The sight's left side as Holosun draws it: the hood, its front face leaning back, its rear top corner chamfered and its rear face running down into the deck by a round; the deck, the lip across its rear end, the lip's corner facet's notch."},"front":{"plane":"zy","origin":"the hood's middle (x over its upper rows, clear of the tray's cover), the underside","offset":{},"points":[[-0.495,0.625],[-0.493,0.461],[-0.487,0.455],[-0.487,0.297],[-0.495,0.202],[-0.492,0],[-0.001,0],[0.492,0],[0.509,0.021],[0.524,0.026],[0.524,0.111],[0.555,0.13],[0.555,0.372],[0.548,0.377],[0.509,0.377],[0.495,0.405],[0.493,0.865],[0.481,0.894],[0.455,0.924],[0.428,0.941],[0.391,0.949],[-0.384,0.949],[-0.416,0.943],[-0.462,0.911],[-0.485,0.869],[-0.487,0.662],[-0.493,0.656]],"scaleRefs":["holosun-eps-carry.width","holosun-eps-carry.height"],"inputs":{"holosun-eps-carry.height":0.95,"holosun-eps-carry.width":1.05},"tolerance":0.004,"photo":"references/holosun-eps-carry 169abca1c98b (Holosun EU, the EPS Carry's dimensioned drawing, the end view from the front)","method":"luminance < 200, inside [205, 762, 737, 1235], closing ×2, largest piece, holes filled, opening after the fill 7 px ×1, inset 1 px (half the outline's stroke); scale from holosun-eps-carry.width = 1.05 in (x-extent 507 px → 482.9 px/in) and holosun-eps-carry.height = 0.95 in (y-extent 458 px → 482.1 px/in), which agree within 0.2%; mean 482.5 px/in; origin at x center, y min of the outline (x over 0.05–0.55 of the height from the top); Douglas-Peucker at 0.004 in with the extremes kept: 27 points (IoU 0.998 with the full outline) (tools/trace.py)","via":"harvest","note":"The sight from the front: the hood with its rounded top edges over the base, the battery tray's cover standing from the right flank (z > 0), the buttons' pad 0.008 from the left."}},"gaps":[{"what":"Holosun's US product photos and its manual (cdn.prod.website-files.com)","need":"That host's robots.txt answered 403 on 2026-11-06 and the harvester left it alone; the EU shop's photos are of the same sight (its serial on the left side)."},{"what":"The hood's section between the front and rear faces (what the window's tunnel is inside, how thick the walls are)","need":"A view through the window from a quarter, or a section; drawn as a straight tunnel of the window's size."}]},"holosun-hm3x":{"id":"holosun-hm3x","name":"HM3X 3× magnifier with flip mount","manufacturer":"Holosun","sku":"HM3X","category":"magnifier","description":"Flip-to-side mount, with its height spacer in (1.63 in, for a lower 1/3 co-witness sight) or out (1.41 in, absolute co-witness, as Holosun ships it): the QD lever on the rifle's left, the hinge on its right. In line behind the red dot, or swung aside to the right.","weight":"holosun-hm3x.weight","fitments":{"label":"Height","default":"spacer","setup":true,"says":"Holosun: \"The default configuration of the HM3X is 1.41\" (absolute co-witness height). A spacer is included to raise the magnifier to 1.63\" (lower 1/3 co-witness height).\"","options":{"spacer":{"label":"With the spacer","params":{},"source":"https://cdn.prod.website-files.com/68f92fcb2648b8aa5dc55d79/696084c37ac69a1d308fa08f_holosun-hm3x-manual.pdf"},"no_spacer":{"label":"Without the spacer","params":{},"anchors":{"optical_axis":{"origin":[0,"{.optical_axis_above_rail_no_spacer}",0],"note":"Without the spacer: Holosun's \"Without the spacer, the center height is 1.41\" (Abs. CW).\""},"eyepiece":{"origin":["-{.eyepiece_rear_behind_base}","{.optical_axis_above_rail_no_spacer}",0],"note":"The eyepiece ring's rear face, on the axis, the spacer out."}},"components":{"inline":"inline_no_spacer","aside":"aside_no_spacer"},"weight":"holosun-hm3x.weight","source":"https://cdn.prod.website-files.com/68f92fcb2648b8aa5dc55d79/696084c37ac69a1d308fa08f_holosun-hm3x-manual.pdf"}}},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":[0,0,0]},"optical_axis":{"origin":[0,"{.optical_axis_above_rail_spacer}",0],"note":"With the spacer in, the catalog's default (its fitments: out, it is lower by the spacer)."},"eyepiece":{"origin":["-{.eyepiece_rear_behind_base}","{.optical_axis_above_rail_spacer}",0],"note":"The eyepiece ring's rear face, on the axis. Holosun gives the eye relief behind it: 70 mm."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":"={.mount_base_length} / 2","clamp_front":"={.mount_base_length} / 2"},"flips":false,"note":"The flip mount's base, 1.93 in long about the frame's origin: its clamp runs the base's length."},"sight_line":{"type":"optic.sight_line","role":"magnifier","params":{"magnification":"1x"},"flips":false,"note":"What it goes behind. Holosun's page: \"The HM3X is a rugged 3X magnifier designed to extend the capability of red dot optics on rifles and carbines\"."}},"eye":{"anchor":"eyepiece","relief":["{.eye_relief}"],"note":"Holosun: 70 mm (2.75 in)."},"folds":{"up":"inline","folded":"aside","note":"Holosun's manual: \"The magnifier can be flipped to the side 90 degrees (as shown in Figure 3).\" Its page: \"Ambidextrous flip-to-side mount allows instant transition between magnified and unmagnified views\".","says":{"field":"Magnifier","up":"In line","folded":"Aside","toUp":"swing it in line","toFolded":"swing it aside"}},"materials":{"body":{"label":"Housing","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized_matte","color":"placeholder-black","sku":"HM3X","source":"https://www.holosun.com/products/hm3x"}},"default":"black","note":"Black is the one colour it is sold in. Holosun's page: \"Rugged aluminum construction with MAO surface finish provides excellent durability and corrosion resistance\", \"Housing Material Durable Aluminum\", \"Surface Finish MAO\", \"Housing Color Black\" (its EU shop: \"Material: aluminium\", \"Housing Color: black\"). MAO is a micro-arc oxide coat: a dusty matte black in Primary Arms' photo of the left side, the two knurled rings, the two adjuster caps and the foot under the housing all the housing's own tone: drawn as matte anodize, and a black isn't fitted to a photo. The rubber cover it ships with (the EU shop's delivery content lists \"HS Rubber Cover\") isn't drawn."},"mount":{"label":"Flip mount","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","sheen":"satin","note":"The base with the strip in its top, the hinge block with its knuckles and the tension screw's boss, the QD lever with its two ears, the clamp's nose behind its roller, the catch its rear end lies on and the slotted link ahead of it, the barrel, the flip plate and the spacer: black in every photo, a smoother and deeper black than the housing (Primary Arms' photo of the left side; in Holosun's of the right side the barrel carries a soft highlight along it that nothing on the housing does). No page on file says what the mount is finished in: drawn as the housing's finish a step smoother."},"hardware":{"label":"Screws and adjustment tool","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The adjustment tool's knurled knob behind the hinge (the manual's Figure 1: \"Adjustment Tool\"), the clamp bolt's Torx head on the hinge block's face, the two Torx screws under the flip plate (the manual: \"Remove the two screws at the bottom\"), the two screws of the strip in the base's top (the manual's Figures 3 and 4), the roller between the lever's ears and the socket screw in the lever's recess: black, with the glint of blacked steel on the knob's knurl and the bolt's head in Holosun's and Primary Arms' photos, where the mount beside them has none; the roller is bright steel in Holosun's pictures and a dark grey bush in Primary Arms' photograph, and is drawn with the rest. No page on file says what they are made of: drawn as dark steel. Black in the one colourway there is."},"lens":{"label":"Lenses","finish":"glass","recolorable":false,"color":"glass-clear"}},"components":{"body":{"label":"Housing","material":"body"},"mount":{"label":"Flip mount","material":"mount"},"lens":{"label":"Lenses","material":"lens"}},"geometry":{"components":{"inline":"holosun-hm3x.inline.glb","aside":"holosun-hm3x.aside.glb","inline_no_spacer":"holosun-hm3x.inline_no_spacer.glb","aside_no_spacer":"holosun-hm3x.aside_no_spacer.glb"},"approximations":["The housing is a visual hull of Holosun's dimensioned drawing (side and end views), revolved about the optical axis: the drawing's end view shows only the eyepiece ring's circle around the housing, so the housing is taken as round. Between its rings the round is the body's own under the top boss (2026-10-13): the side view's top line carried straight across from the boss's one foot to its other, and at each foot carried round its corner over a tenth of an inch either side (the traced line turns 6 degrees at the front foot and 2 at the rear, and a round turned at sharp corners is shaded as three bands; the curve is within 0.003 in of the trace). Until then the round was turned at the top edge with the boss in it, and the end view's lugs came with it all the way round the body as a collar 0.9 in long that no picture has.","The mount is two pieces a hinge joins. What stays on the rail: the base and its clamp from the drawing's two views, on its right the hinge block, two knuckles with the tension screw's slotted boss and the adjustment tool's knob on the rear one (the manual's Figure 1 names both) and the clamp bolt's head on its face, and on its left the QD lever. What swings: a round barrel between the knuckles, the flip plate from it across the base, the spacer, the magnifier's foot and the housing. The hinge's place and sizes are read on Holosun's picture of the right side and its picture of the mount alone from above, each good to a few hundredths of an inch.","Swung aside it is turned 90 degrees about that hinge, as the manual states, over to the rifle's right: the housing lies beside the rail with its eyepiece still to the rear, the flip plate stands on the hinge with its two screws' heads toward the rail (the manual's Figures 3 and 4). Where it comes to rest follows from the hinge's place, so it is good to about a twentieth of an inch.","Three looks, each a material of the model: the housing with its foot; the mount's own metal (base, strip, hinge block, lever, clamp nose, catch, link, barrel, flip plate, spacer); and the steel on it (the adjustment tool's knob, the clamp bolt's head, the flip plate's two screws, the strip's two, the lever's roller and the screw in its recess). Each piece is closed and stands 0.005 to 0.02 in into its neighbour, so the model's volume counts that little twice (about a hundredth of a cubic inch of 7.6).","The two rings are fluted (2026-10-13). Round the objective ring sixteen flutes, counted on Holosun's view from that end, where they notch the rim: a hundredth of an inch deep with sloping walls, as wide as the lands between them, open at both ends of the ring, one at the top. Round the eyepiece ring fourteen, counted on Primary Arms' photo of the left side by the angle between them: wider, flat-floored, closed 0.03 in short of each end of the ring, one at each side as that photo has the ring turned (it is the diopter ring, and turns). How deep the eyepiece ring's are isn't read, its rim having no notch to show it: they are drawn as deep as the objective ring's, with walls as wide as they are deep. The objective ring's front corner is squared off: the traced outline has a rim there, 0.03 in prouder than the ring and 0.02 in ahead of its front face, where the drawing's extension lines meet the corner, and neither the photos of the side nor the view from the end have one. From where the traced ring is narrowest it is carried forward at that radius to the front face, which makes the housing 4.04 in long for the drawing's 4.03 (4.06 with the corner).","The QD lever is drawn closed and level, as Holosun's drawing has it in both views (Holosun's own pictures have it unlatched and hanging; Primary Arms' photo has it swung right open and pointing forward): two ears about a steel roller a tenth of an inch ahead of the base's middle, the arm from them back past the base's rear end, leaning in from the ears' outer edge to lie on a catch block on the base's wall, a recess in its outer face with the lever lock's screw in it, the clamp's nose between the wall and the roller, and a slotted link in the base's side ahead of the ears. Not read, and assumed: the recess is a third of the arm deep and the screw's socket half its head; the catch is as tall as the lever in front of it and the clamp's nose as tall as the roller; the link stands a third of the arm's thickness off the wall. The pad at the arm's rear end is plain: its ribs are 0.029 in apart, finer than a page draws.","The base is as long as the hinge block beside it and flush with its front, 1.73 in (2026-10-13: Holosun's drawing has the two as one block in its side view, Primary Arms' photo of the left side and the manual's Figure 4 agree; it was drawn 1.6 in long with its front 0.16 in behind the front knuckle, read on the picture of the mount from above, which is taken aslant: both readings are in the ledger). The rail channel under it runs its length. Its left side is its wall, 0.604 in left of the middle: until that day it was the lever's end silhouette run the drawing's whole length.","In the base's top, under the flip plate, the strip with two screws that the manual's Figures 3 and 4 draw there: read by proportion on those figures (good to a twentieth of an inch), midway between the knuckles. How it is seated isn't read: a pocket an eighth of the strip's width deep with as much room round it, the strip's top half of that under the base's, its screws' heads three quarters of its width across. It shows when the magnifier is swung aside. The tension screw's slot is level across the rifle, as the manual draws it, and as deep as it is wide (not read).","Not drawn: what is on the flip plate's top face (the picture of the mount alone from above has two recessed screws, a centre pin and cross grooves there): the spacer and the magnifier's foot cover it in both states. Nor the keys by which plate, spacer and foot fit together (the foot and the spacer are plain blocks as long as the flip plate), the lever's ribs, the anti-rotation plate round the clamp bolt's head (the manual's Figure 6), knurling and markings.","Which side is which: the QD lever is on the rifle's left, the mount's hinge and the round cap on the body's flank on its right, so the magnifier swings over to the right. Holosun's drawing and its photos of the two sides, of the underside and from the objective end all have it so (the drawing's end view is seen from the objective end; until 2026-10-05 it was read as seen from the eyepiece and the model was mirrored). Holosun's page calls the mount ambidextrous (\"Ambidextrous flip-to-side mount allows instant transition between magnified and unmagnified views\") and says no more: how it is set to swing to the left isn't on file, and the model has this one arrangement.","On the round, what the drawing's two views have standing off it, each where a picture has it along the body (2026-10-13). On top the elevation adjuster's cap: the side view's own boss turned about its upright axis, round and 0.63 in across as the end view has its lug, on a low seat as wide as the cap that runs 0.89 in along the body's top with round ends. On the right flank the windage adjuster's cap: a drum of the same size (the end view's other lug) to the face the drawing has, 0.786 in from the axis, in one plane with the top cap (Holosun's picture of the right side has their middles within two hundredths). Each has a coin slot 0.22 by 0.06 in, read on that picture and drawn as deep as it is wide (not read), along the housing on the top cap and upright on the flank's: a slot stands however its adjuster is turned. The caps' edges are square: the black groove round each cap's inner disc (0.016 in wide) and its rim's round aren't drawn.","On each flank the HOLOSUN oval, as an outline with no letters: a flat-faced pad with rounded ends and, inside a rim 0.02 in wide, a sunk field. The left one (1.24 by 0.31 in, under the top cap) stands to the face the drawing's end view has there, 0.739 in from the axis, which is a hundredth of an inch past the round where the round is widest under it and more toward the objective, where the body narrows; how deep the field is sunk isn't read, and it is drawn down to the round at the oval's middle (0.016 in). That the end view's bump and the photos' oval are one thing is a reading: the photos have the field shaded inside its edge all round, the drawing has something standing off the flank over exactly the oval's height. The right one is smaller (1.0 by 0.245 in, read on Holosun's picture of the right side) and behind the cap, toward the eyepiece; the end view has the cap in front of it, so it stands as far off the round as the left one where the round is widest under it, its field as deep: assumed.","The magnifier's foot has five slanted pockets in each side (2026-10-13): four whole ones 0.13 in wide and 0.2 in apart and a fifth, rearmost, cut short by an upright wall near the foot's rear end, leaning 30 degrees with their tops toward the objective, between a level bottom line and a top line that falls toward the eyepiece under the housing. Counted and read on Holosun's drawing of the left side; Holosun's picture of the right side has the same five there. They are sunk (each has its shaded wall on the side the light comes from, in a photo of each side); how deep they are sunk isn't seen, and they are drawn a fiftieth of an inch deep, an assumption. Their corners are square (the drawing rounds them), and the foot itself is still a plain block as long as the flip plate.","Not drawn on the housing: the panels' lines along the flanks (a long panel above and one below the oval's row on each side, a short pad ahead of each oval and one behind it, a band along the top from the cap toward each ring: steps a hundredth of an inch or so, no view gives their depth), and the letters.","Spacer drawn as a block under the foot, 0.22 in thick (Holosun's two centre heights), as long and as wide as the flip plate a little inside the foot's sides; how it is keyed to the plate and the foot isn't drawn. With it out (the build's choice, D95) the magnifier stands on the flip plate 0.22 in lower, the rest of the mount as it was: four models, in line and aside, each with and without it.","Lenses at the end faces, at their measured diameters (objective 0.906, eyepiece 0.912); their recess behind the retainers isn't sourced.","The rail's place under the base is the rail's own head in section (MIL-STD-1913's, since 2026-10-12) from the rail's top down to the lower gauge line 0.154 in under it, inside the side outline: the hull's own was the drawing's end view's dovetail, a hundredth or two smaller than a rail's head and a fortieth of an inch to the right of the frame's middle, so it stood in a rail's left flank and off its right. Below that line the jaws are the drawing's, less what stood inside a rail's lower faces."],"ledger":["holosun-hm3x.length","holosun-hm3x.width","holosun-hm3x.height","holosun-hm3x.optical_axis_above_rail_spacer","holosun-hm3x.spacer_thickness","holosun-hm3x.flip_angle","holosun-hm3x.hinge_axis_above_rail","holosun-hm3x.hinge_axis_right_of_centre","holosun-hm3x.hinge_barrel_d","holosun-hm3x.hinge_block_length","holosun-hm3x.hinge_knuckle_length"]},"profiles":{"side":{"plane":"xy","origin":"the part frame: the rail top under the mount base's centre (no spacer; the mesh adds it at the interface)","offset":{},"points":[[-2.995,0.748],[-2.978,0.75],[-2.946,0.713],[-2.633,0.713],[-2.602,0.734],[-2.598,0.785],[-2.577,0.806],[-2.455,0.806],[-2.434,0.785],[-2.434,0.715],[-2.418,0.699],[-1.89,0.708],[-0.797,0.675],[-0.762,0.649],[-0.762,0.332],[-0.783,0.311],[-0.946,0.311],[-0.958,0.294],[-0.963,-0.005],[-0.923,0.002],[-0.902,-0.019],[-0.897,-0.126],[-0.867,-0.161],[-0.815,-0.175],[-0.708,-0.17],[-0.652,-0.222],[0.894,-0.222],[0.878,-0.201],[0.913,-0.166],[0.941,-0.138],[0.962,-0.154],[0.967,0.701],[0.955,0.712],[0.633,0.712],[0.612,0.738],[0.642,0.773],[0.694,0.773],[0.712,0.759],[1.021,0.768],[1.049,0.74],[1.065,0.752],[1.042,0.78],[1.046,2.037],[1.065,2.074],[1.053,2.086],[1.025,2.058],[0.712,2.067],[0.694,2.053],[0.642,2.053],[-0.002,2.128],[-0.016,2.142],[-0.096,2.147],[-0.131,2.186],[-0.119,2.203],[-0.727,2.203],[-0.759,2.198],[-0.801,2.156],[-0.881,2.151],[-0.895,2.137],[-1.736,2.109],[-2.189,2.109],[-2.207,2.123],[-2.436,2.128],[-2.434,2.042],[-2.455,2.021],[-2.576,2.021],[-2.597,2.042],[-2.597,2.084],[-2.633,2.114],[-2.946,2.109],[-2.99,2.06]],"scaleRefs":["holosun-hm3x.mount_base_length","holosun-hm3x.clamp_below_rail","holosun-hm3x.top_above_rail_no_spacer","holosun-hm3x.optical_axis_above_rail_no_spacer","holosun-hm3x.axis_to_mount_interface"],"inputs":{"holosun-hm3x.axis_to_mount_interface":0.97,"holosun-hm3x.clamp_below_rail":0.22,"holosun-hm3x.mount_base_length":1.93,"holosun-hm3x.optical_axis_above_rail_no_spacer":1.41,"holosun-hm3x.top_above_rail_no_spacer":2.2},"tolerance":0.01,"photo":"references/holosun-hm3x 1fac54f9923c (Holosun dimensioned drawing, side view (inches))","method":"luminance < 200, inside [318, 770, 1195, 1300], closing ×2, largest piece, holes filled, inset 2 px (half the outline's stroke); frame from the reviewed holes base_front_bottom, base_rear_bottom, base_front_top, base_rear_top, axis, interface, rail (214.1 px/in, rms 0.003 in over 7 points); origin at the photo's frame; Douglas-Peucker at 0.01 in with the extremes kept: 71 points (IoU 0.996 with the full outline); checks: median row width in y [1.0, 1.8] (4.041–4.041) 4.041 ± 0.017 in vs holosun-hm3x.length 4.03 ± 0 (conflict): agrees; height 2.425 ± 0.015 in vs holosun-hm3x.height 2.42 ± 0 (conflict): agrees (tools/trace.py)","via":"harvest","note":"Line art: the outline encloses everything seen from the side, rings, housing, flip mount and clamp."},"front":{"plane":"zy","origin":"the optical axis's vertical (z 0, above the rail's centre) at the rail top","offset":{},"points":[[-0.873,0.001],[-0.855,-0.027],[-0.869,-0.041],[-0.873,-0.139],[-0.82,-0.132],[-0.787,-0.17],[-0.731,-0.174],[-0.675,-0.221],[-0.358,-0.207],[-0.327,-0.167],[-0.388,-0.093],[-0.306,0.003],[0.347,0.003],[0.442,-0.088],[0.363,-0.177],[0.363,-0.214],[0.561,-0.221],[0.596,-0.186],[0.596,0.192],[0.657,0.374],[0.652,0.63],[0.608,0.689],[0.57,0.707],[0.319,0.712],[0.298,0.733],[0.505,0.875],[0.673,1.099],[0.787,1.092],[0.783,1.722],[0.673,1.724],[0.522,1.927],[0.312,2.086],[0.312,2.188],[0.295,2.2],[-0.302,2.2],[-0.313,2.188],[-0.313,2.086],[-0.484,1.967],[-0.556,1.894],[-0.687,1.703],[-0.729,1.582],[-0.719,1.549],[-0.738,1.493],[-0.738,1.405],[-0.752,1.391],[-0.738,1.377],[-0.715,1.195],[-0.687,1.12],[-0.561,0.933],[-0.456,0.833],[-0.295,0.728],[-0.295,0.458],[-0.313,0.439],[-0.295,0.42],[-0.281,0.346],[-0.239,0.308],[-0.26,0.287],[-0.563,0.287],[-0.619,0.231],[-0.675,0.236],[-0.703,0.213],[-0.782,0.208],[-0.82,0.171],[-0.862,0.171],[-0.859,0.052]],"scaleRefs":["holosun-hm3x.top_above_rail_no_spacer","holosun-hm3x.optical_axis_above_rail_no_spacer","holosun-hm3x.axis_to_mount_interface"],"inputs":{"holosun-hm3x.axis_to_mount_interface":0.97,"holosun-hm3x.optical_axis_above_rail_no_spacer":1.41,"holosun-hm3x.top_above_rail_no_spacer":2.2},"tolerance":0.01,"photo":"references/holosun-hm3x 1fac54f9923c (Holosun dimensioned drawing, end view (inches))","method":"luminance < 200, inside [1435, 770, 1810, 1300], closing ×2, largest piece, holes filled, inset 2 px (half the outline's stroke); frame from the reviewed holes top, axis, interface, rail (214.4 px/in, rms 0.001 in over 4 points); origin at the photo's frame; Douglas-Peucker at 0.01 in with the extremes kept: 65 points (IoU 0.993 with the full outline); checks: width 1.661 ± 0.015 in vs holosun-hm3x.width 1.66 ± 0 (conflict): agrees; height 2.421 ± 0.016 in vs holosun-hm3x.height 2.42 ± 0 (conflict): agrees (tools/trace.py)","via":"harvest"}},"gaps":[{"what":"How the mount is set to swing to the left. Holosun's page calls it ambidextrous; the manual on file draws it swinging to the right and says nothing of turning it round.","need":"Holosun's instructions for reversing the mount, or a picture of one set up left-handed."},{"what":"How much of the base's length its clamp's jaws grip, and where its recoil lugs are. The interface gives the mount the drawing's whole 1.93 in of rail, which is what it takes of the rail's length (that figure runs from the front knuckle to the adjustment tool's knob, both over the rail's right edge); the base is 1.73 in long and the rail channel is drawn the length of it. The picture of the magnifier from below (3bcb120eaf6e) has the left jaw in two stretches with the moving jaw between them, and two lugs in the channel's roof: taken from close and not square on, nothing of them is read.","need":"A view of the mount's underside square on, with the jaws and the recoil lugs in it."},{"what":"How deep the eyepiece ring's flutes are: they are closed at both ends, so no rim shows them in outline. Drawn as deep as the objective ring's, a hundredth of an inch.","need":"A view of the eyepiece ring from its end and a little to one side, or a close one across its top, where a flute shows against the background."},{"what":"The lines of the panels along the housing's flanks and top: seen in every photo of either side and in the drawing's side view, not drawn. Where they are is read (2026-10-19, the drawing's side view at its 214.1 px/in, from the axis): three rows a flank, each from the housing's front, 0.645 in ahead of the base's middle, to 2.183 in behind it with round rear ends; the upper from 0.66 to 0.265 in over the axis, the middle (the oval's row, a pad ahead of the oval to 0.262 in ahead and one behind it from 1.163 behind) from 0.162 over to 0.154 under, the lower from 0.26 to 0.653 under; between them two bands 0.10 in wide that run the housing's length. How far any of it stands is not: on Primary Arms' photo of the left side (lit from above) each edge is a line a few thousandths of an inch wide with light on both sides of it, not a lit or a shadowed wall, and the drawing's end view has the flank's silhouette a round within its trace's hundredth of an inch at those heights. Whatever relief there is is under a hundredth of an inch (under half a pixel where a whole rifle is drawn, a pixel and a half at a close look), and which side of each edge stands proud isn't settled: not drawn rather than drawn either way.","need":"A close view along the flank from an end, or across the top, where a panel's edge shows as a step against the background."},{"what":"How deep the slanted pockets in the foot's sides are: no view has one in profile. Drawn a fiftieth of an inch deep.","need":"A view of the foot from the front or from below, square on, where a pocket notches the side's edge."},{"what":"How far the right flank's oval stands off the housing, and how deep either oval's field is: the drawing's end view has the left one edge on (0.739 in from the axis) and the adjuster's cap in front of the right one. Drawn with the left one's figures.","need":"A view from the eyepiece end, square on, or along the right flank."},{"what":"The strip in the base's top under the flip plate, and the base's top with the magnifier swung aside: only the manual's two line drawings show it, read by proportion.","need":"A photo of the mount from above with the magnifier swung aside."},{"what":"Where the housing comes to rest when swung aside, to better than a twentieth of an inch: it follows from the hinge's place, read on two pictures.","need":"A picture of the magnifier swung aside, square on from behind or from the front."}]},"holosun-hs510c":{"id":"holosun-hs510c","name":"HS510C Open Reflex MRS Solar QD Mount","manufacturer":"Holosun","sku":"HS510C","url":"https://www.holosun.com/products/hs510c","category":"optic","description":"Holosun's open reflex sight: a 2 MOA dot, a 65 MOA circle or both (\"Reticle 2 MOA Dot & 65 MOA Circle\"), a solar cell on its rear deck, \"aluminum housing with a titanium hood\", a CR2032 in a tray on its side. It comes on its quick-detach mount: \"Integrated QD mount with 1.41 inch dot height for fast installation and iron sight alignment\". Drawn as Holosun draws and photographs it: the QD lever, the battery tray and the windage screw on the rifle's right, the brightness buttons on its left.","weight":"holosun-hs510c.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":[0,0,"{.rail_middle_z}"],"note":"Optic frame: origin on the rail's top surface under the hood's middle, at the middle of the mount's foot along the rail (its bottom edge in the drawing's side view), +x toward the muzzle (the hood's end), +z to the rifle's right (the QD lever's side). The rail's own middle is where the jaws hold it: midway between their two grooves, 0.025 in to the left of the hood's middle by the drawing."},"optical_axis":{"origin":[0,"{.optical_axis_above_rail}",0],"note":"The window's centre: the drawing's 1.41 in above the surface that sits on the rail."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":"={.mount_length} / 2","clamp_front":"={.mount_length} / 2"},"flips":false,"note":"The foot's length along the rail about its middle (the frame's origin), read off the drawing's side view. Holosun's manual: \"The mount bracket is adaptable to standard Picatinny rails.\" Where its cross bar sits along the foot is in the photo from below (a feature of the plan outline); the foot is centred on the slot it is put at."},"sight_line":{"type":"optic.sight_line","role":"sight","params":{"magnification":"1x"},"flips":false,"note":"Holosun's page: \"Magnification 1x\", \"Unlimited Eye Relief Yes\". The eye can be anywhere behind it, so it has no eye point of its own."}},"materials":{"body":{"label":"Housing, hood, mount and lever","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized_matte","color":"placeholder-black","sku":"HS510C","source":"https://www.holosun.com/products/hs510c"},"fde":{"label":"FDE","finish":"anodized_matte","color":"holosun-fde","sku":"HS510C-FDE","source":"https://www.holosun.com/products/hs510c-fde"}},"default":"black","note":"Holosun's page of the black one: \"aluminum housing with a titanium hood\", and its table \"Housing Material Aluminum & Titanium\", \"Surface Finish MAO\", \"Housing Color Black\" (a matte oxide: drawn as `anodized_matte`, the nearest type). The flat dark earth one is HS510C-FDE on Holosun's own page (Primary Arms and Sportsman's Warehouse write HS510C-FDE-R): \"in a durable flat dark earth finish\", \"Durable FDE anodized finish\" (its table there still reads \"Housing Color Black\", a copy of the black page's); Primary Arms: \"Color Flat Dark Earth Finish Hardcoat Anodized\"; Sportsman's: \"Finish Flat Dark Earth Anodized Color Tan\". Holosun's series lists these two and the kit with the HM3X: no other colour. The sights with a green reticle (HE510C-GR, HS510C-GR-FDE) are other models. The hood (titanium), the housing, the mount and the QD lever read one tan in the photos of the FDE sight (hood #a9a188, housing #aea78d, mount #aba38c, lever #aca58a in Impact Guns' right side view) and one black in Primary Arms' of the black one: one slot. Not drawn: the lettering (HOLOSUN in a pale fill with a red dot, the model's name and serial in white), and a black sliver of spring behind the lever's pivot."},"tray":{"label":"Battery tray","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","follows":{"slot":"body","options":{"fde":{"finish":"anodized_matte","color":"holosun-fde-tray"}}},"note":"The battery tray's plate on the right side (Holosun: \"Side Mounted Battery Tray\"). On the black sight it reads as the housing does (#363635 against #363636 in Primary Arms' two side views). On the FDE one it is a paler, yellower tan than the housing round it in every photo of that side (#bab192 against #a9a188 straight on, #b2aa8d from the front quarter): a second part anodized on another day. What it is made of and how it is finished is on no page on file: drawn in the housing's finish."},"pad":{"label":"Buttons' pad","finish":"rubber","recolorable":false,"color":"placeholder-polymer-black","follows":{"slot":"body","options":{"fde":{"finish":"rubber","color":"holosun-fde-rubber"}}},"note":"The pad on the left side with the + and - buttons moulded in it. Black on the black sight, and blacker than the housing (#29292a against #363636); on the FDE sight a browner tan than the housing (#a1967a against #a8a187 beside it). No page on file says what it is made of: by its look, one soft moulding with no sheen, drawn as `rubber`."},"screws":{"label":"Screws and clamp bolt","finish":"steel","recolorable":false,"color":"placeholder-black","follows":{"slot":"body","options":{"fde":{"finish":"anodized_matte","color":"holosun-fde"}}},"note":"The six Torx screws (four through the housing, two in the battery tray), the clamp's Torx bolt in the mount's left side (the manual: \"one Torx socket at the end of clamp adjusting bolt on the side of the mount\"), the windage screw and the elevation screw. On the black sight they are a blacker, glossier black than the housing in Primary Arms' photos: drawn as dark steel. On the FDE sight their heads are the housing's tan (#aca48c and #b1aa94 against #a9a188) with dark sockets and slots: how they are coated isn't said, so they are drawn as the housing is, and their sockets aren't dark."},"solar":{"label":"Solar cell","finish":"polymer","recolorable":false,"color":"holosun-solar-cell","note":"The cell on the deck behind the hood (Holosun: \"Solar Failsafe\"), a dark slate blue with a grid of fine lines under its cover glass in Primary Arms' photo from above; the same in both colours (the FDE's is in shadow in every photo of it on file). No finish type is a solar cell: a plain matte surface (`polymer`) under the cover glass, which is drawn as glass over it and carries the gloss."},"lens":{"label":"Lens and the solar cell's cover","finish":"glass","recolorable":false,"color":"glass-clear","note":"The window's pane, and the clear cover over the solar cell. The pane's red coating as the photos have it from the front isn't a colour of the glass here."}},"components":{"body":{"label":"Housing and hood","material":"body"},"mount":{"label":"QD mount","material":"body"},"lens":{"label":"Lens and solar cell","material":"lens"}},"geometry":{"model":"holosun-hs510c.glb","components":{},"approximations":["The housing and the hood are the hull of Holosun's drawing (side view from the right, end view from the front) and the shop's photo from below: what none of the three shows is flat. The step where the housing widens ahead of the deck is square across, as the plan from below has it; the photos show it as a slanted face.","The plan is the photo from below, which the lever hides on the right: the housing's right wall is its left wall turned over about the middle, and the plan's width is set to the drawing's (the photo reads it within 0.3%).","The window is the frame's opening in the drawing's end view (1.26 in wide, the page's figure) cut straight through the hood from the front to where the housing's top comes down behind it; the floor under it is flat at the opening's sill. The ribbed ramp the photos show on that floor isn't drawn.","The glass is a pane just behind the hood's front face and parallel to it, its rim inside the frame: its depth and its lean aren't in any straight view.","What stands off or into a face does so by 0.012 in (the tray's plate and tab, the buttons' pad, the HOLOSUN panel, the screws' counterbores, the + and -, the lever's ribs), twice that for the buttons and the windage screw; the screws' sockets are round, a little under half their heads across (the photos show Torx): no source gives these depths, and the drawing's end view shows nothing standing out of the housing's sides by more than 0.02 in. The tray's plate and the pad, each a piece of its own colour, stand that 0.012 in off the side wall where the plan has it furthest out along them, so that all of each shows: over the stretch where the plan from below has the wall 0.02 in further in, they stand that much more.","The solar cell is drawn as a dark slab under a cover glass a few thousandths thick, its cells' lines as grooves in the glass: the pale lines between the cells that the photos show aren't a colour of their own. The screws' sockets and slots are the screws' colour (dark in the FDE sight's photos, against tan heads).","The left side's pad, buttons, screws and the opening under the housing are placed from one seller's straight photo of that side, scaled by the drawing's length and height (they fit its outline within 2%); the left screws' heads are the size the drawing gives the right side's.","The deck's rear corners are cut by the facet whose edge on the side wall the drawing's side view draws (0.40 in along the wall under the top chamfer, running out toward the bottom), as far across the rear face as along the wall at each height: that it is 45 degrees in plan is assumed (Holosun's render from behind has the ridge left between the two facets about a quarter of the deck's width; drawn, it is a third).","The deck's top edges are chamfered from the line the drawing's side view has under them, at 45 degrees (the angle is assumed). The solar cell is a glass panel on the flat behind the hood, as wide as the window (its width is assumed), its two rows of five cells, counted on Holosun's photo from above and behind, drawn as grooves in the glass, and the elevation screw is in the middle of the deck's rear block at the windage screw's size (the manual: \"The elevation adjustment screw is at top rear end of the sight\"; where along the block isn't in any straight view).","The QD lever is the hull of its three outlines (the side view's arm and block, its shape from below, its end in the end view), a slab against the mount's right face, with the 18 ribs the drawing has across its arm cut into its outer face: its latch and its pivot pin aren't drawn. The mount's foot behind the lever is drawn as the left side's photo has it.","The clamp bolt's head is a plain disc at the drawing's height and stand-off, where the left photo has it along the foot. The cross bar under the mount is in the outline as the slot's ceiling over the rail; where it sits along the foot (the photo from below has it) isn't cut into the model.","No lettering: the HOLOSUN marks, the model's name and serial on the mount, the R and arrow by the windage screw.","The rail's slot under the foot is the rail's own head in section (MIL-STD-1913's, since 2026-10-12) from the rail's top down to the lower gauge line 0.154 in under it, about the rail's middle between the jaws: the drawing's front outline is within five thousandths of it, over on one face and under on another. Below that line the jaws are the drawing's, less what stood inside a rail's lower faces."],"ledger":["holosun-hs510c.rail_middle_z","holosun-hs510c.jaw_opening","holosun-hs510c.length","holosun-hs510c.width","holosun-hs510c.height","holosun-hs510c.optical_axis_above_rail","holosun-hs510c.window_center_above_base","holosun-hs510c.window_width","holosun-hs510c.mount_length","holosun-hs510c.clamp_below_rail","holosun-hs510c.clamp_bottom_y"]},"profiles":{"front":{"plane":"zy","origin":"the hood's middle (the window's, and the rail slot's under it); the clamp's bottom, offset to the rail's top","offset":{"y":"clamp_bottom_y"},"points":[[-0.851,0.593],[-0.831,0.6],[-0.819,0.589],[-0.828,0.556],[-0.81,0.523],[-0.647,0.356],[-0.675,0.272],[-0.675,0.193],[-0.647,0.1],[-0.647,0.044],[-0.603,0],[-0.37,0.005],[-0.377,0.054],[-0.442,0.119],[-0.442,0.128],[-0.351,0.219],[0.319,0.219],[0.34,0.174],[0.391,0.123],[0.391,0.114],[0.33,0.054],[0.34,0.03],[0.365,0.009],[0.468,0.009],[0.482,0],[0.612,0],[0.651,0.035],[0.656,0.058],[0.677,0.074],[0.854,0.07],[0.891,0.093],[0.938,0.093],[0.954,0.123],[0.954,0.337],[0.945,0.356],[0.928,0.368],[0.886,0.368],[0.863,0.386],[0.7,0.386],[0.689,0.398],[0.81,0.519],[0.819,0.533],[0.819,0.584],[0.838,0.603],[0.838,1.119],[0.814,1.221],[0.81,1.901],[0.805,1.961],[0.777,2.04],[0.7,2.136],[0.63,2.178],[0.547,2.21],[0.277,2.28],[0.03,2.303],[-0.212,2.289],[-0.458,2.238],[-0.663,2.159],[-0.726,2.11],[-0.777,2.036],[-0.8,1.97],[-0.81,1.896],[-0.814,1.212],[-0.833,1.128],[-0.833,0.612]],"features":{"window":[[[0.628,1.273],[0.628,1.901],[0.6,1.966],[0.542,2.019],[0.426,2.061],[0.244,2.103],[0.072,2.122],[-0.072,2.122],[-0.272,2.098],[-0.454,2.052],[-0.523,2.029],[-0.565,2.001],[-0.61,1.947],[-0.628,1.896],[-0.628,1.282],[-0.61,1.226],[-0.57,1.177],[-0.519,1.145],[-0.458,1.131],[0.458,1.131],[0.523,1.145],[0.561,1.168],[0.605,1.217]]],"panel":[[[0.721,0.612],[0.721,1.077],[0.714,1.084],[-0.714,1.084],[-0.721,1.077],[-0.721,0.612],[-0.71,0.6],[0.714,0.605]]],"lever":[[[0.952,0.398],[0.649,0.398],[0.649,0.04],[0.952,0.04]]],"bolt":[[[-0.658,0.365],[-0.691,0.365],[-0.691,0.077],[-0.658,0.077]]],"bar":[[[0.416,0.375],[-0.416,0.375],[-0.416,0.216],[0.416,0.216]]]},"scaleRefs":["holosun-hs510c.width","holosun-hs510c.height"],"inputs":{"holosun-hs510c.height":2.31,"holosun-hs510c.width":1.8},"tolerance":0.006,"photo":"references/holosun-hs510c edefb31cce90 (Holosun EU dimensioned drawing, end view from the front (the HOLOSUN panel under the window; the QD lever at the picture's left))","method":"luminance < 170, inside [1405, 696, 1812, 1204], pieces ≥ 400 px, closing ×1, largest piece, holes filled, inset 1 px (half the outline's stroke); scale from holosun-hs510c.width = 1.8 in (x-extent 388 px → 215.6 px/in) and holosun-hs510c.height = 2.31 in (y-extent 495 px → 214.3 px/in), which agree within 0.6%; mean 214.9 px/in; origin at x center, y min of the outline (x over 0.1–0.5 of the height from the top); Douglas-Peucker at 0.006 in with the extremes kept: 64 points (IoU 0.997 with the full outline); checks: median row width in y [0.65, 1.1] (1.670–1.670) 1.670 ± 0.015 in vs holosun-hs510c.body_width 1.68 ± 0 (confirmed): agrees; features through the same placement (window: the innermost window line: the opening that shows glass from the front; panel: the recessed panel the HOLOSUN logo stands in, on the housing's front face; lever: the QD lever seen end on, standing off the mount's right side; bolt: the clamp bolt's head on the mount's left side; bar: the cross bar under the mount, whose underside sits on the rail (the 1.41 in line ends on it)) (tools/trace.py)","via":"harvest","note":"From the front, mirrored into the frame. The lever's end and the clamp bolt's head are in the outline; the window is a feature."},"side":{"plane":"xy","origin":"the middle of the mount's foot (its bottom edge, the lowest rows); the clamp's bottom, offset to the rail's top","offset":{"y":"clamp_bottom_y"},"points":[[-1.83,1.134],[-1.83,0.887],[-1.821,0.873],[-1.83,0.859],[-1.807,0.836],[-1.723,0.622],[-1.716,0.47],[-1.474,0.466],[-1.362,0.419],[-1.323,0.384],[-1.346,0.361],[-1.341,0.109],[-1.32,0.098],[-1.148,0.102],[-1.067,0.012],[-1.069,0],[-1.05,0.014],[-1.036,0],[-1.022,0.009],[-0.999,0],[-0.976,0.009],[-0.966,0],[-0.957,0.009],[1.055,0.014],[1.092,0.033],[1.118,0.063],[1.449,0.533],[1.439,0.543],[1.439,0.589],[1.463,0.612],[1.463,1.167],[1.199,2.31],[0.203,2.315],[0.191,2.28],[0.177,2.103],[0.154,1.991],[0.102,1.833],[0.028,1.674],[-0.056,1.539],[-0.154,1.418],[-0.272,1.3],[-0.403,1.197],[-0.533,1.118],[-0.585,1.099],[-0.929,1.099],[-0.999,1.206],[-1.8,1.206],[-1.826,1.171]],"features":{"mount":[[[-1.712,0.617],[1.451,0.617],[1.451,0.533],[1.129,-0.002],[-1.102,-0.002],[-1.325,0.179],[-1.325,0.422],[-1.516,0.468],[-1.712,0.477]]],"lever":[[[-1.344,0.384],[-0.491,0.384],[-0.491,0.445],[0.743,0.445],[0.743,0.026],[-0.491,0.026],[-0.491,0.105],[-1.344,0.105]]],"lever_ribs":[[[-1.288,0.384],[-0.435,0.384],[-0.435,0.105],[-1.288,0.105]]],"hood":[[[0.193,2.317],[1.195,2.317],[1.46,1.223],[1.46,1.209],[-0.342,1.209],[-0.259,1.283],[-0.142,1.4],[0.021,1.633],[0.137,1.865],[0.184,2.098]]],"glass":[[[1.167,2.317],[1.432,1.223],[1.386,1.223],[1.12,2.317]]],"tray":[[[-0.305,0.994],[1.139,0.994],[1.139,0.668],[-0.305,0.668]]],"tray_tab":[[[0.161,1.064],[0.673,1.064],[0.673,0.994],[0.161,0.994]]],"tray_screws":[[[-0.212,0.897],[-0.1,0.897],[-0.1,0.785],[-0.212,0.785]],[[0.934,0.897],[1.046,0.897],[1.046,0.785],[0.934,0.785]]],"housing_screws":[[[-0.65,0.953],[-0.398,0.953],[-0.398,0.701],[-0.65,0.701]],[[1.171,0.953],[1.423,0.953],[1.423,0.701],[1.171,0.701]]],"windage":[[[-1.493,1.036],[-1.167,1.036],[-1.167,0.71],[-1.493,0.71]],[[-1.437,0.98],[-1.223,0.98],[-1.223,0.766],[-1.437,0.766]]],"deck_chamfer":[[[-1.712,1.181],[-0.585,1.181],[-0.585,1.088],[-1.712,1.088]]],"deck_corner":[[[-1.418,1.092],[-1.66,0.813],[-1.819,1.185]]],"solar":[[[-0.92,1.129],[-0.594,1.129],[-0.594,1.092],[-0.92,1.092]]],"windage_slot":[[[-1.348,0.971],[-1.306,0.971],[-1.306,0.771],[-1.348,0.771]]],"housing_screw_heads":[[[-0.603,0.906],[-0.445,0.906],[-0.445,0.748],[-0.603,0.748]],[[1.218,0.906],[1.376,0.906],[1.376,0.748],[1.218,0.748]]]},"scaleRefs":["holosun-hs510c.length","holosun-hs510c.height"],"inputs":{"holosun-hs510c.height":2.31,"holosun-hs510c.length":3.3},"tolerance":0.006,"photo":"references/holosun-hs510c edefb31cce90 (Holosun EU dimensioned drawing, side view from the right (the hood, at the muzzle's end, to the right; the QD lever toward the rear))","method":"luminance < 170, inside [340, 696, 1070, 1204], 1 boxes excluded, pieces ≥ 400 px, closing ×1, largest piece, holes filled, inset 1 px (half the outline's stroke); scale from holosun-hs510c.length = 3.3 in (x-extent 707 px → 214.2 px/in) and holosun-hs510c.height = 2.31 in (y-extent 497 px → 215.2 px/in), which agree within 0.4%; mean 214.7 px/in; origin at x center, y min of the outline (x over 0.975–1.0 of the height from the top); Douglas-Peucker at 0.006 in with the extremes kept: 48 points (IoU 0.996 with the full outline); features through the same placement (mount: the QD mount without its lever: the plate under the housing and the foot over the rail. The foot's rear is behind the lever in this view: its corner, its rear face and where that meets the plate are as the left side's photo has them (53e72360435d: 157, 107 and 107 px of 1553 ahead of the housing's rear end, 0, 77 and 192 px of 1070 above the bottom); lever: the QD lever's ribbed arm and the block it turns in, on the mount's right side; lever_ribs: the ribs across the lever's arm: 18 of them, counted on the drawing's row 1135 as the dark runs that begin at columns 469, 480, 490, 500, 510, 521, 531, 542, 552, 562, 573, 584, 594, 604, 615, 626, 637 and 647 (one every 10.5 px); the photo from below shows them as teeth on the arm's outer face; hood: the hood: above the line where it meets the housing, ahead of its concave rear edge; glass: where the pane is drawn: a band just behind the hood's front face and parallel to it. The drawing doesn't show the glass from the side: its depth and its lean are assumed; tray: the battery tray's plate on the right side (a slot with round ends); tray_tab: the tab over the tray's plate; tray_screws: the tray's two screws; housing_screws: the two screws through the housing, behind and ahead of the tray, with their counterbores; windage: the windage screw on the deck's right side: its boss and its slotted disc; deck_chamfer: the strip along the deck's top edge: from the deck's top down to the line the drawing has under it, back from where the hood begins. The top-rear photo (10a9fed902fe) shows it as a chamfer; its angle isn't in any straight view; deck_corner: the facet that takes off the deck's rear corner, as the side view has it: its edge on the side wall from under the top chamfer (441, 966) down and back to (389, 1026), and the deck's top rear corner. The FDE sight's straight side photo (7c65b21ff280) has the same facet, 0.40 in along the wall at its top. How far it cuts across the rear face isn't in a straight view: Holosun's render from behind (4cb1c5d76129) has it about a fifth of the deck's width at its top; solar: the flat behind the hood, a step below the deck's rear block, where the photo from above and behind (10a9fed902fe) has the solar cell: its length along the sight; windage_slot: the slot across the windage screw's disc, upright as drawn; housing_screw_heads: the heads of the two housing screws, down their counterbores (the second of the drawing's nested circles)) (tools/trace.py)","via":"harvest","note":"The whole sight on its mount from the right. The lever's arm reaches behind the foot; the housing's screws, tray and windage screw are features."},"plan":{"plane":"xz","origin":"the housing's rear end; the outline's edge on the side without the lever (the housing's left side): the model sets both against the drawing's two views","offset":{},"points":[[0,0.847],[0.007,0.595],[0.104,0.121],[0.113,0.098],[0.144,0.076],[0.265,0.069],[0.785,0.074],[1.025,0.06],[1.087,0.012],[1.58,0.009],[1.616,0.03],[1.653,0.03],[2.617,0.012],[2.867,0.018],[2.924,0.005],[3.243,0],[3.287,0.007],[3.298,0.036],[3.291,0.075],[3.288,1.582],[3.3,1.623],[3.283,1.657],[2.834,1.652],[2.797,1.641],[2.673,1.638],[2.437,1.666],[2.125,1.668],[2.11,1.764],[2.096,1.794],[2.026,1.839],[1.963,1.849],[1.903,1.828],[1.845,1.77],[1.799,1.74],[1.402,1.692],[1.374,1.675],[1.344,1.685],[1.325,1.671],[1.293,1.68],[1.274,1.666],[1.238,1.675],[1.224,1.662],[1.207,1.673],[1.187,1.673],[1.17,1.659],[1.143,1.673],[1.122,1.659],[1.087,1.671],[1.069,1.659],[1.039,1.673],[1.018,1.659],[0.99,1.675],[0.967,1.662],[0.946,1.678],[0.914,1.666],[0.895,1.682],[0.865,1.668],[0.845,1.687],[0.815,1.675],[0.791,1.694],[0.764,1.682],[0.745,1.701],[0.72,1.694],[0.681,1.724],[0.581,1.731],[0.56,1.719],[0.54,1.742],[0.496,1.74],[0.471,1.714],[0.471,1.679],[0.505,1.641],[0.525,1.635],[0.53,1.615],[0.55,1.607],[0.555,1.584],[0.573,1.575],[0.567,1.564],[0.144,1.555],[0.104,1.529],[0.002,1.034]],"features":{"lever":[[[2.109,1.561],[2.104,1.792],[2.062,1.838],[1.982,1.845],[1.901,1.815],[1.866,1.778],[1.381,1.688],[1.173,1.674],[0.676,1.674],[0.618,1.72],[0.503,1.739],[0.475,1.688],[0.491,1.561]]],"bar":[[[2.086,1.203],[2.086,0.382],[1.889,0.382],[1.889,1.203]]]},"scaleRefs":["holosun-hs510c.length"],"inputs":{"holosun-hs510c.length":3.3},"tolerance":0.006,"photo":"references/holosun-hs510c d5fc8d363436 (Holosun EU, the HS510C on its mount from straight below (front at the top, the QD lever at the picture's left))","method":"luminance < 200, closing ×2, largest piece, holes filled; rotated -90.0° as declared; scale from holosun-hs510c.length = 3.3 in (x-extent 1428 px → 432.7 px/in); origin at x min, y min of the outline; Douglas-Peucker at 0.006 in with the extremes kept: 80 points (IoU 0.997 with the full outline); checks: height 1.849 ± 0.007; width 3.300 ± 0.009; features through the same placement (lever: the QD lever from below: its lobe at the pivot and its arm along the mount's side to its tail, out to the mount's side (the inner edge is the picture's column 800); bar: the cross bar under the mount (the recoil lug), across the rail slot) (tools/trace.py)","via":"harvest","note":"A photo from below: the outline is the widest of the housing, the mount and the lever at each station."},"left":{"plane":"xy","origin":"the middle of the mount's foot (its bottom edge); the clamp's bottom, offset to the rail's top","offset":{"y":"clamp_bottom_y"},"points":[[-1.829,1.194],[-1.826,0.875],[-1.769,0.613],[-1.756,0.596],[-1.762,0.588],[-1.758,0.472],[-1.489,0.452],[-1.427,0.43],[-1.359,0.392],[-1.323,0.361],[-1.325,0.234],[-1.317,0.172],[-1.299,0.154],[-1.226,0.152],[-1.217,0.141],[-1.185,0.141],[-1.126,0.044],[-1.102,0.021],[-1.072,0.006],[-1.035,0.002],[-0.001,0.002],[0.082,0],[1.04,0.002],[1.082,0.011],[1.135,0.055],[1.31,0.307],[1.46,0.494],[1.482,0.536],[1.48,0.579],[1.471,0.59],[1.492,0.603],[1.488,1.222],[1.287,2.102],[1.22,2.269],[1.196,2.293],[0.436,2.295],[0.206,2.294],[0.191,2.153],[0.139,1.943],[0.079,1.787],[-0.034,1.583],[-0.135,1.453],[-0.241,1.343],[-0.378,1.229],[-0.545,1.12],[-0.92,1.12],[-0.992,1.214],[-1.02,1.216],[-1.725,1.22],[-1.806,1.216]],"features":{"pad":[[[0.898,1.072],[-0.055,1.072],[-0.307,0.825],[-0.194,0.622],[0.984,0.622],[1.102,0.714],[1.106,0.832]]],"buttons":[[[0.873,0.999],[0.539,0.999],[0.539,0.665],[0.873,0.665]],[[0.294,1.01],[-0.04,1.01],[-0.04,0.676],[0.294,0.676]]],"plus":[[[0.791,0.845],[0.62,0.845],[0.62,0.819],[0.791,0.819]],[[0.718,0.917],[0.693,0.917],[0.693,0.746],[0.718,0.746]]],"minus":[[[0.213,0.855],[0.042,0.855],[0.042,0.83],[0.213,0.83]]],"screws":[[[1.455,0.907],[1.241,0.907],[1.241,0.693],[1.455,0.693]],[[-0.376,0.917],[-0.59,0.917],[-0.59,0.703],[-0.376,0.703]]],"bolt":[[[0.331,0.404],[-0.033,0.404],[-0.033,0.04],[0.331,0.04]]],"gap":[[[0.518,0.592],[-0.286,0.597],[-0.291,0.592],[-0.187,0.492],[-0.08,0.492],[-0.074,0.499],[0.414,0.492]]]},"scaleRefs":["holosun-hs510c.length","holosun-hs510c.height"],"inputs":{"holosun-hs510c.height":2.31,"holosun-hs510c.length":3.3},"tolerance":0.006,"photo":"references/holosun-hs510c 53e72360435d (Primary Arms (HS510C_02), the black HS510C's left side, straight on (the hood to the left))","method":"luminance < 200, closing ×2, largest piece, holes filled; scale from holosun-hs510c.length = 3.3 in (x-extent 1551 px → 470.0 px/in) and holosun-hs510c.height = 2.31 in (y-extent 1072 px → 464.1 px/in), which agree within 1.3%; mean 467.0 px/in; origin at x center, y min of the outline (x over 0.975–1.0 of the height from the top); Douglas-Peucker at 0.006 in with the extremes kept: 50 points (IoU 0.998 with the full outline); checks: median row width in y [0.005, 0.03] (2.125–2.225) 2.189 ± 0.015; features through the same placement (pad: the brightness buttons' pad: a long six-sided plate; buttons: the + button (toward the muzzle) and the - button; plus: the + moulded into the forward button: its two bars; minus: the - moulded into the rear button; screws: the two Torx screws through the housing, ahead of and behind the pad; bolt: the clamp bolt's domed head, in the foot; gap: the opening between the housing and the foot that the backdrop shows through) (tools/trace.py)","via":"harvest","note":"The left side: the foot whole (no lever in front of it), the buttons, the clamp's bolt. A photo: used for what is where on this side, with the drawing for sizes."}},"gaps":[{"what":"A straight view from above","need":"The solar cell's size, where the elevation screw stands on the deck and the ribbed floor under the hood: the plan on file is a photo from below, which shows only the widest outline at each station."},{"what":"A second straight view of the left side","need":"The buttons' pad, the two screws, the clamp's bolt and the opening under the housing are placed from one seller's straight photo of the left side (Primary Arms), which the drawing's two sizes fit to 2%; it reads the foot 0.06 in longer than the drawing does."},{"what":"The deck's facets across the sight","need":"A straight view from behind and one from above: how far the rear corners' facets and the top edges' chamfers cut across is assumed (45 degrees each); only their edges on the side wall are in a straight view."},{"what":"How deep the glass sits and how it leans","need":"A section, or a straight side view through the hood: the pane is drawn just behind the front face and parallel to it."},{"what":"What Holosun's 215 g is made of","need":"The body (4.94 oz, 140 g) and the mount (45 g) as published add to 185 g; a scale reading of the sight with and without its battery and mount would settle the 30 g between."},{"what":"What the battery tray's plate and the buttons' pad are made of","need":"A page or a manual that names them: the pad is drawn as rubber and the tray in the housing's finish, each by its look in the photos"},{"what":"Holosun's own photos of the FDE sight","need":"Its colours are matched to one distributor's three photographs (Impact Guns' and Sportsman's Warehouse's pages show the same set): Holosun's own are on a host whose robots.txt can't be read, and are left alone. A second photographer's FDE sight would check the tan, the tray's and the pad's."}]},"huxwrx-flash-hider-qd-556":{"id":"huxwrx-flash-hider-qd-556","name":"Flash Hider-QD 556 1/2x28","manufacturer":"HUXWRX","sku":"1677","url":"https://huxwrx.com/flash-hider-qd-556-1-2x28/","category":"muzzle_device","description":"HUXWRX's flash hider for a 1/2x28 muzzle, and the mount its FLOW and HX-QD suppressors lock onto: a hexagonal plate for the wrench at the rear, the suppressor's coarse left-hand thread and a taper ahead of it, then a slotted body with six helical slots round a core that carries the bore. Black steel. Sold alone, and in the box with a FLOW 556K or FLOW 556 Ti as their kits.","weight":"huxwrx-flash-hider-qd-556.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"thread":{"origin":[0,0,0],"note":"Device frame: on the bore axis at the barrel's shoulder, +x toward the muzzle. The hex plate's rear face bears on the shoulder: no washer or shim is listed with it, and the manual has it threaded \"directly onto the barrel\"."},"front":{"origin":["{.length}",0,0],"note":"The muzzle ring's face: where the build's overall length ends without a suppressor."},"suppressor_seat":{"origin":["{.suppressor_seat_x}",0,0],"note":"On the bore axis where a suppressor's rear face stands when it is locked on, +x toward the muzzle: the hex plate's front face, which the suppressor's collar comes down to (the maker's rendering of the pair seated shows the hex behind the suppressor; the ledger's suppressor_seat_x says how it was read, and how it stands against the suppressors' published added lengths)."}},"interfaces":{"thread":{"type":"muzzle_thread","role":"device","anchor":"thread","params":{"thread":"1/2-28","thread_length_made_for":"={.thread_length}"},"flips":false,"note":"HUXWRX: \"FLASH HIDER-QD 556 1/2X28\"; \"Muzzle device length is 2.3 inches, length added to the barrel is 1.7 inches (on barrels with 0.6\" threads)\" (https://huxwrx.com/flash-hider-qd-556-1-2x28/). What it is made for, not a limit: the depth of its threaded hole isn't published. The manual: \"Thread the QD muzzle device directly onto the barrel of the host firearm. Using a HUXWRX QD wrench with torque wrench, index the hex flats on the muzzle device and torque it to approximately 33ft-lbf (45 Nm).\""},"suppressor_mount":{"type":"suppressor_mount","role":"device","anchor":"suppressor_seat","params":{"system":"huxwrx-qd"},"flips":false,"note":"HUXWRX's QD mount with its \"Torque Lock\" (a left-hand thread and a taper). The maker, of this part: \"The Flash Hider-QD 556 is compatible with the HX-QD series (556k, 556, 762, 762 Ti, and Magnum Ti) and FLOW series (556k 556 Ti, 6k, and 762 Ti) suppressors. This flash hider is only compatible with VENTUM series suppressors when combined with the HUX HUB Adapter. NOTE: Larger caliber mounts are NOT compatible with smaller caliber suppressors. Smaller caliber mounts ARE compatible with larger caliber suppressors.\" (https://huxwrx.com/flash-hider-qd-556-1-2x28/). The FLOW manual: \"FLOW Suppressors require a HUXWRX QD muzzle device.\" and \"Thread the suppressor counter-clockwise onto the QD muzzle device until hand-tight.\" (https://huxwrx.com/content/manuals/FLOWManual.pdf)."}},"materials":{"body":{"label":"Flash hider","finish":"steel","recolorable":false,"color":"placeholder-black","note":"One finish, black. The maker names neither the steel nor the finish; Alexander's: \"Material: Steel Finish: Black\" and \"the black finish cleans up easily after extended time under a suppressor\" (https://alexandersstore.com/product/hux-flash-hider-qd-556-1-2x28/), AR15Discounts: \"Color: Black\". In every photo on file a smooth black with a hard highlight along its turned edges and the tool's fine lines showing through (Rooftop Defense's two, 1e8bfe213942 and 477c03bb60a8; AR15Discounts', 39436d699911): a black on machined steel, not a matte coat, so it isn't fitted to a photo. Which process (nitride, oxide) no page says."}},"components":{},"geometry":{"model":"huxwrx-flash-hider-qd-556.glb","components":{},"approximations":["Turned and cut from figures read off one seller's photo of the part standing (AR15Discounts'), at the scale its two published sizes give together (the maker's 2.3 in length, a seller's 1.20 in diameter across the hex's corners: 0.7% apart). The photo is a close one, taken from above: each station along the part carries ± 0.02 in.","The rear plate is a hexagon 1.04 in across its flats cut on a 1.20 in round, 0.145 in thick; nine holes in its rear face on ten places, the tenth left solid and taken to be the one behind the flat that has the cross hole (the two would meet there; no photo shows both at once). The holes are drawn as deep as the plate is thick: how deep they go isn't seen.","The suppressor's thread is a left-hand helix of plain V form, 0.083 in to the turn (twelve to the inch by the photo; its size is published nowhere), 1.123 in across its crests and cut down to the relief's diameter behind it, since the photo doesn't show how deep its grooves are. In the photos its crests are broad flats with narrow grooves between; the model's are sharp.","Six helical slots, right-hand, 45 degrees wide at their widest and narrowing to a point toward the muzzle, turning 35 degrees to the inch (two readings of the one photo, 29 and 42: the middle). Six is counted from the slots' spacing round the near side of the body (60 degrees), not on a view from the muzzle, which no page has. Each slot's edges are cut square to the surface; the real ones are a round cutter's, with a rounded rear end.","Inside the slotted body: a cavity as wide as the muzzle ring's opening, and on the axis a core tube with the bore through it, its end just under the muzzle face with four lugs standing on it (two cuts across the end at right angles, seven tenths of the bore wide). The photos show lugs with gaps between them on the core's end, and a ribbed core through the slots; how many lugs, and the core's ribs, aren't settled from the oblique views on file and the ribs aren't drawn.","The hole for the barrel's thread is a plain hole of the thread's nominal half inch, as deep as the 0.6 in of thread the maker states its lengths for and 0.025 in more (the Army's barrel has .625): the 1/2-28 thread inside it isn't cut.","The hex is drawn with a flat up; where it stops when torqued is the barrel's thread's to say. Edges broken at 0.008 in."],"ledger":["huxwrx-flash-hider-qd-556.length","huxwrx-flash-hider-qd-556.od","huxwrx-flash-hider-qd-556.hex_thickness","huxwrx-flash-hider-qd-556.hex_across_flats","huxwrx-flash-hider-qd-556.neck_d","huxwrx-flash-hider-qd-556.neck_length","huxwrx-flash-hider-qd-556.qd_thread_od","huxwrx-flash-hider-qd-556.qd_thread_pitch","huxwrx-flash-hider-qd-556.qd_thread_length","huxwrx-flash-hider-qd-556.cone_rear_x","huxwrx-flash-hider-qd-556.cone_rear_d","huxwrx-flash-hider-qd-556.body_x","huxwrx-flash-hider-qd-556.body_d","huxwrx-flash-hider-qd-556.slots","huxwrx-flash-hider-qd-556.slot_rear_x","huxwrx-flash-hider-qd-556.slot_front_x","huxwrx-flash-hider-qd-556.slot_width","huxwrx-flash-hider-qd-556.slot_taper_x","huxwrx-flash-hider-qd-556.slot_twist","huxwrx-flash-hider-qd-556.ring_id","huxwrx-flash-hider-qd-556.core_od","huxwrx-flash-hider-qd-556.bore_d","huxwrx-flash-hider-qd-556.core_recess","huxwrx-flash-hider-qd-556.core_notch_depth","huxwrx-flash-hider-qd-556.rear_holes","huxwrx-flash-hider-qd-556.rear_hole_circle_d","huxwrx-flash-hider-qd-556.rear_hole_d","huxwrx-flash-hider-qd-556.cross_hole_d","huxwrx-flash-hider-qd-556.thread_length","huxwrx-flash-hider-qd-556.thread_major_d","huxwrx-flash-hider-qd-556.suppressor_seat_x"]},"profiles":{},"gaps":[{"what":"The slots' count and the core's end, on a view that shows the whole turn","need":"a photo straight on at the muzzle end (none at the maker or at eight sellers); six slots is counted from their spacing on a side view"},{"what":"The suppressor's thread: its size, how deep it is cut, its form","need":"the maker's drawing of the QD mount, or a straight, sharp side photo of the thread against a scale (the photo on file is soft at the grooves)"},{"what":"Where a suppressor's rear face stands on it, against the suppressors' published added lengths","need":"a photo of a FLOW suppressor on a rifle, square from the side, that shows the hex behind it (or doesn't): the maker's rendering shows it, and the published added lengths would have the suppressor 0.17 to 0.21 in further back"},{"what":"Weight and diameter from the maker","need":"HUXWRX states neither; three sellers give 3.3 oz and one 1.20 in"},{"what":"Its steel and its finish in the maker's words","need":"a page that names them: 'Steel' and 'Black' are one seller's"}]},"huxwrx-flow-556-ti":{"id":"huxwrx-flow-556-ti","name":"FLOW 556 Ti","manufacturer":"HUXWRX","sku":"3059","url":"https://huxwrx.com/flow-556-ti","category":"suppressor","description":"HUXWRX's full-size 5.56 flow-through suppressor: 3D-printed in Grade 5 titanium and Cerakoted, 6.8 in long and 1.8 across, with a hexagonal collar at the mount end, raised grip dashes round its rear third and a domed cap of sixteen swirled pockets round a three-ribbed nose. The can alone: it locks onto HUXWRX's QD muzzle devices (a part of its own), and is also sold in a kit with the Flash Hider-QD 556 (3292 black, 3291 FDE).","weight":"huxwrx-flow-556-ti.weight","nfa":"silencer","cartridge":{"takes":["5.56 NATO",".223 Rem",".17 HMR","5.7x28mm",".22 LR"],"stated":"CALIBER 5.56, .223, 17 HMR, 5.7, 22 LR, 5.45","source":"HUXWRX, FLOW 556 Ti white paper, PRODUCT SPECIFICATIONS: https://huxwrx.com/content/white-paper/FLOW-556-Ti-White-Paper.pdf (its 5.45 has no name in data/cartridges.yaml yet). The maker's page: \"The first full-size 5.56 suppressor from the FLOW series is full-auto rated with no barrel restrictions.\""},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"mount":{"origin":[0,0,0],"note":"Suppressor frame: on its axis at its rear face, the hex collar's, +x toward the muzzle. On HUXWRX's QD muzzle devices that face comes down to the device's hex plate (the device's `suppressor_seat`)."},"front":{"origin":["{.length}",0,0],"note":"The tip of the front cap: where the build's overall length ends."}},"interfaces":{"mount":{"type":"suppressor_mount","role":"suppressor","anchor":"mount","params":{"system":"huxwrx-qd"},"flips":false,"note":"HUXWRX's QD mount with its Torque Lock. The maker's page: \"Compatible with Muzzle Brake-QD 556 and Flash Hider-QD 556\" (https://huxwrx.com/flow-556-ti); its white paper: \"MOUNTS 556 QD Muzzle Brakes and Flash Hiders\"; the FLOW manual: \"FLOW Suppressors require a HUXWRX QD muzzle device.\" and \"Thread the suppressor counter-clockwise onto the QD muzzle device until hand-tight. Reference the lock/unlock icon on the suppressor to verify rotation direction. The suppressor should be firmly seated.\" (https://huxwrx.com/content/manuals/FLOWManual.pdf). Barrel lengths, the white paper: \"BARREL LENGTH No restrictions\"; its page: \"full-auto rated with no barrel restrictions. No modifications (other than QD muzzle device) to the platform\"."}},"materials":{"body":{"label":"Suppressor","finish":"cerakote","recolorable":false,"color":"huxwrx-black-cerakote-ti","options":{"black":{"label":"Matte Black","finish":"cerakote","color":"huxwrx-black-cerakote-ti","sku":"3059","source":"https://www.primaryarms.com/huxwrx-flow-5-56-ti-suppressor-black"},"fde":{"label":"Flat Dark Earth","finish":"cerakote","color":"huxwrx-fde-cerakote","sku":"2693","source":"https://www.primaryarms.com/huxwrx-flow-556-ti-556-nato-suppressor-fde"}},"default":"black","note":"The whole can is one printed piece, coated: \"COATINGS C-Series Cerakote™ Matte Black (Flat Dark Earth available)\" (HUXWRX's white paper); \"The FLOW 556 Ti is fully 3D-printed with Grade 5 Titanium and is coated with C-series high temperature Cerakote® in both FDE & Black\" (https://huxwrx.com/flow-556-ti). In both colourways the cap, the collar and the grip dashes are the body's colour (the maker's and Primary Arms' photos of the black one, the maker's and Mile High's of the FDE one); only the inside of the mount is bare. The maker's page gives no numbers: 3059 and 2693 are Primary Arms' SKU and MPN for the can alone; the kits with the flash hider are 3292 (black, Mile High) and 3291 (FDE, Alexander's)."},"socket":{"label":"Mount's inside","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"Uncoated inside the collar: the thread and the taper in bare, bright titanium (Primary Arms' photo of the rear end, 581f5002d00f; \"Grade 5 Titanium\", the white paper). Drawn as bright metal under the catalog's bare-steel look, which is not titanium's own: not fitted to a photo."}},"components":{"body":{"label":"Suppressor","material":"body"},"socket":{"label":"Mount's inside","material":"socket"}},"geometry":{"model":"huxwrx-flow-556-ti.glb","components":{},"approximations":["The outside is turned from the maker's own side outline (its white paper's drawing, vector art, scaled by the length and diameter dimensioned on it), the body at its published diameter. The outside only: the flow-through core, its coils and its chambers aren't modelled, and behind its skin the model is solid but for the mount's socket and the bore, so its volume is no measure of its weight (as titanium it would weigh about three times the published figure).","The mount end's collar is a hexagon with rounded corners at the drawing's size, a flat up; where it stops when locked on is the thread's to say. Inside it, the socket is the Flash Hider-QD 556's own outside, taken from that part's ledger at the seat the two share: its thread (a left-hand helix, cut into the socket's wall so that crest meets root), the step, the taper and the room for its slotted body, with the bore beyond. No source gives the socket's own sizes: it is drawn to fit the device it locks onto, with no clearance.","The inside of the mount is its own piece (bare metal, where the body is coated): a sleeve 0.03 of the thread's diameter thick lining the socket, a few thousandths inside the rear face.","The grip texture: twenty columns of three raised dashes each round the rear third, every other column set forward, standing half the published 0.05 in off the body, each a plain bar that follows the shoulder where it runs onto it. The real dashes have rounded ends, and the first rank bends with the shoulder as drawn.","The front cap: 16 pockets round its shoulder, as the drawing's end view counts them, each a blind pocket as deep as it is wide, leaning 50 degrees from straight toward the middle (read by eye). On the real can they open into the core; their true depth and their curved floors aren't sourced.","The cap's middle: three flat sectors sunk a quarter of a rib's width below the turned nose, leaving three ribs from the bore's boss to the pockets' ring. How deep the sectors lie isn't measured; the slit the drawing shows along a rib isn't cut.","Not drawn: the engraved markings and the lock and unlock icons, the printed surface's grain. Edges broken at 0.01 in."],"ledger":["huxwrx-flow-556-ti.length","huxwrx-flow-556-ti.od","huxwrx-flow-556-ti.grip_texture","huxwrx-flow-556-ti.collar_across_flats","huxwrx-flow-556-ti.collar_corner_r","huxwrx-flow-556-ti.collar_length","huxwrx-flow-556-ti.bore_d","huxwrx-flow-556-ti.cap_slots","huxwrx-flow-556-ti.cap_slot_r_in","huxwrx-flow-556-ti.cap_slot_r_out","huxwrx-flow-556-ti.cap_slot_width","huxwrx-flow-556-ti.cap_slot_lean","huxwrx-flow-556-ti.nose_rib_width","huxwrx-flow-556-ti.nose_boss_d","huxwrx-flow-556-ti.grip_columns","huxwrx-flow-556-ti.grip_ranks","huxwrx-flow-556-ti.grip_first_x","huxwrx-flow-556-ti.grip_stagger","huxwrx-flow-556-ti.grip_pitch","huxwrx-flow-556-ti.grip_dash_length","huxwrx-flow-556-ti.grip_dash_width"]},"profiles":{"side":{"plane":"xy","origin":"the hex collar's rear face, on the axis","offset":{},"points":[[0,0.621],[0,-0.001],[0,-0.621],[0.01,-0.639],[0.029,-0.65],[0.24,-0.65],[0.296,-0.663],[0.337,-0.683],[0.358,-0.705],[0.362,-0.727],[0.39,-0.744],[0.441,-0.788],[0.456,-0.79],[0.466,-0.798],[0.509,-0.844],[0.542,-0.864],[0.56,-0.861],[0.577,-0.878],[0.581,-0.892],[0.619,-0.91],[0.654,-0.92],[0.692,-0.925],[0.774,-0.925],[0.802,-0.904],[1.056,-0.904],[1.079,-0.922],[1.226,-0.922],[1.485,-0.917],[1.503,-0.904],[1.759,-0.904],[1.77,-0.912],[1.94,-0.912],[2.207,-0.904],[6.023,-0.904],[6.071,-0.899],[6.114,-0.889],[6.175,-0.866],[6.272,-0.816],[6.34,-0.77],[6.364,-0.746],[6.484,-0.593],[6.552,-0.497],[6.789,-0.187],[6.801,-0.151],[6.799,0.017],[6.688,0.091],[6.669,0.111],[6.686,0.127],[6.79,0.127],[6.801,0.136],[6.801,0.171],[6.796,0.192],[6.762,0.236],[6.734,0.239],[6.706,0.254],[6.564,0.351],[6.524,0.387],[6.499,0.431],[6.499,0.57],[6.375,0.733],[6.34,0.77],[6.272,0.816],[6.175,0.866],[6.107,0.892],[6.053,0.902],[2.207,0.904],[1.942,0.912],[1.772,0.912],[1.759,0.904],[1.505,0.904],[1.485,0.917],[1.231,0.922],[1.079,0.922],[1.056,0.904],[0.802,0.904],[0.774,0.925],[0.69,0.925],[0.634,0.915],[0.581,0.892],[0.577,0.878],[0.56,0.861],[0.542,0.864],[0.509,0.844],[0.456,0.79],[0.441,0.788],[0.39,0.744],[0.362,0.727],[0.358,0.705],[0.339,0.686],[0.309,0.668],[0.24,0.65],[0.029,0.65],[0.005,0.634]],"scaleRefs":["huxwrx-flow-556-ti.length","huxwrx-flow-556-ti.grip_od"],"inputs":{"huxwrx-flow-556-ti.grip_od":1.85,"huxwrx-flow-556-ti.length":6.8},"tolerance":0.003,"photo":"references/huxwrx-flow-556-ti 1af30bbd3c1c (HUXWRX, FLOW 556 Ti white paper: the side outline over its 6.8in / 17.2cm dimension line (the page at 600 dpi, 6600 x 5100))","method":"luminance < 128, inside [1780, 1020, 4510, 1790], closing ×3, largest piece, holes filled, inset 3 px (half the outline's stroke); scale from huxwrx-flow-556-ti.length = 6.8 in (x-extent 2677 px → 393.7 px/in) and huxwrx-flow-556-ti.grip_od = 1.85 in (y-extent 728 px → 393.5 px/in), which agree within 0.0%; mean 393.6 px/in; origin at x min, y center of the outline; Douglas-Peucker at 0.003 in with the extremes kept: 93 points (IoU 0.999 with the full outline); checks: height (tooth tops, max over 0.4 in windows) along x [2.2, 5.6] 1.809 ± 0.049; height (tooth tops, max over 0.1 in windows) along x [0.03, 0.19] 1.301 ± 0.036 (tools/trace.py)","via":"harvest","note":"The mount end (the hex collar) at the rear, the cap at the front. A drawing's outline: the grip texture's dashes that fall on the edge stand on it, and the cap's slots that fall on the edge notch it; the model turns the body at its published diameter and cuts the slots itself."}},"gaps":[{"what":"The cap's pockets: their depth and their curved floors","need":"a second view of the muzzle end from the side, close: Mile High's straight-on photo gives their plan and not their depth"},{"what":"The mount's socket: its thread, its taper and its depth","need":"the maker's drawing of the QD mount; it is drawn to fit the flash hider"},{"what":"How far the can's front stands ahead of the muzzle: the pair as drawn against the maker's 6.1 in","need":"a photo of the can on a rifle square from the side, with the barrel's shoulder in view"},{"what":"5.45 in the maker's list of calibers","need":"a name for it in data/cartridges.yaml"}]},"huxwrx-flow-556k":{"id":"huxwrx-flow-556k","name":"FLOW 556K","manufacturer":"HUXWRX","sku":"2448","url":"https://huxwrx.com/flow-556k","category":"suppressor","description":"HUXWRX's short 5.56 flow-through suppressor: 3D-printed in 17-4 stainless steel and Cerakoted, 5.5 in long, with a hexagonal collar at the mount end, raised grip dashes round its rear third and a domed cap of eighteen pockets round a three-ribbed nose. The can alone: it locks onto HUXWRX's QD muzzle devices (a part of its own), and is also sold in a kit with the Flash Hider-QD 556 (2449 black, 2450 FDE).","weight":"huxwrx-flow-556k.weight","nfa":"silencer","cartridge":{"takes":["5.56 NATO",".223 Rem",".17 HMR","5.7x28mm",".22 LR"],"stated":"CALIBER 5.56, .223, 17 HMR, 5.7, 22 LR, 5.45","source":"HUXWRX, FLOW 556k white paper, PRODUCT SPECIFICATIONS: https://huxwrx.com/content/white-paper/FLOW-556k-White-Paper.pdf (its 5.45 has no name in data/cartridges.yaml yet). The maker's page: \"It is full-auto rated and compatible on 5.56, 17 HMR, and 5.7 platforms.\""},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"mount":{"origin":[0,0,0],"note":"Suppressor frame: on its axis at its rear face, the hex collar's, +x toward the muzzle. On HUXWRX's QD muzzle devices that face comes down to the device's hex plate (the device's `suppressor_seat`)."},"front":{"origin":["{.length}",0,0],"note":"The tip of the front cap: where the build's overall length ends."}},"interfaces":{"mount":{"type":"suppressor_mount","role":"suppressor","anchor":"mount","params":{"system":"huxwrx-qd"},"flips":false,"note":"HUXWRX's QD mount with its Torque Lock. The maker's page: \"Compatible with Muzzle Brake-QD 556 and Flash Hider-QD 556\" (https://huxwrx.com/flow-556k); its white paper: \"MOUNTS 556 QD Muzzle Brakes and Flash Hiders\"; the FLOW manual: \"FLOW Suppressors require a HUXWRX QD muzzle device.\" and \"Thread the suppressor counter-clockwise onto the QD muzzle device until hand-tight. Reference the lock/unlock icon on the suppressor to verify rotation direction. The suppressor should be firmly seated.\" (https://huxwrx.com/content/manuals/FLOWManual.pdf). Barrel lengths, the white paper: \"BARREL LENGTH No restrictions\"."}},"materials":{"body":{"label":"Suppressor","finish":"cerakote","recolorable":false,"color":"huxwrx-black-cerakote","options":{"black":{"label":"Matte Black","finish":"cerakote","color":"huxwrx-black-cerakote","sku":"2448","source":"https://www.primaryarms.com/huxwrx-flow-556k-suppressor-only-black"},"fde":{"label":"Flat Dark Earth","finish":"cerakote","color":"huxwrx-fde-cerakote","sku":"2159","source":"https://www.primaryarms.com/huxwrx-flow-556k-suppressor-only-fde"}},"default":"black","note":"The whole can is one printed piece, coated: \"COATINGS C-Series Cerakote™ Matte Black (Flat Dark Earth available)\" (HUXWRX's white paper); \"The FLOW 556k is fully 3D-printed in 17-4 stainless steel and is coated with C-series high temperature Cerakote®\" (https://huxwrx.com/flow-556k), \"AVAILABLE IN BLACK & FDE\". In both colourways the cap, the collar and the grip dashes are the body's colour (Primary Arms' four photos of the black one, the maker's and Primary Arms' of the FDE one); only the inside of the mount is bare. The maker's page gives no numbers: 2448 and 2159 are Primary Arms' MPNs for the can alone; the kits with the flash hider are 2449 (black) and 2450 (FDE) at Primary Arms and Mile High."},"socket":{"label":"Mount's inside","finish":"stainless","recolorable":false,"color":"huxwrx-17-4-heat-tint","note":"Uncoated inside the collar: the thread and the taper, in bare 17-4 stainless with the straw to bronze tint of its heat treatment (Primary Arms' photo of the rear end, 2b9dfd529686; \"17-4 Heat Treated Stainless Steel\", the white paper). Bright metal: not fitted to a photo."}},"components":{"body":{"label":"Suppressor","material":"body"},"socket":{"label":"Mount's inside","material":"socket"}},"geometry":{"model":"huxwrx-flow-556k.glb","components":{},"approximations":["The outside is turned from the maker's own side outline (its white paper's drawing, vector art, scaled by the length and diameter dimensioned on it), the body at its published diameter. The outside only: the flow-through core, its coils and its chambers aren't modelled, and behind its skin the model is solid but for the mount's socket and the bore, so its volume is no measure of its weight (as stainless steel it would weigh about three times the published figure).","The mount end's collar is a hexagon with rounded corners at the drawing's size, a flat up; where it stops when locked on is the thread's to say. Inside it, the socket is the Flash Hider-QD 556's own outside, taken from that part's ledger at the seat the two share: its thread (a left-hand helix, cut into the socket's wall so that crest meets root), the step, the taper and the room for its slotted body, with the bore beyond. No source gives the socket's own sizes: it is drawn to fit the device it locks onto, with no clearance.","The inside of the mount is its own piece (bare metal, where the body is coated): a sleeve 0.03 of the thread's diameter thick lining the socket, a few thousandths inside the rear face.","The grip texture: twenty columns of three raised dashes each round the rear third, every other column set forward, standing half the published 0.05 in off the body, each a plain bar that follows the shoulder where it runs onto it. The real dashes have rounded ends, and the first rank bends with the shoulder as drawn.","The front cap: 18 pockets round its shoulder, as the drawing's end view counts them, each a blind pocket as deep as it is wide, leaning 15 degrees from straight toward the middle (read by eye). On the real can they open into the core; their true depth and their curved floors aren't sourced.","The cap's middle: three flat sectors sunk a quarter of a rib's width below the turned nose, leaving three ribs from the bore's boss to the pockets' ring. How deep the sectors lie isn't measured; the slit the drawing shows along a rib isn't cut.","Not drawn: the engraved markings and the lock and unlock icons, the printed surface's grain. Edges broken at 0.01 in."],"ledger":["huxwrx-flow-556k.length","huxwrx-flow-556k.od","huxwrx-flow-556k.grip_texture","huxwrx-flow-556k.collar_across_flats","huxwrx-flow-556k.collar_corner_r","huxwrx-flow-556k.collar_length","huxwrx-flow-556k.bore_d","huxwrx-flow-556k.cap_slots","huxwrx-flow-556k.cap_slot_r_in","huxwrx-flow-556k.cap_slot_r_out","huxwrx-flow-556k.cap_slot_width","huxwrx-flow-556k.cap_slot_lean","huxwrx-flow-556k.nose_rib_width","huxwrx-flow-556k.nose_boss_d","huxwrx-flow-556k.grip_columns","huxwrx-flow-556k.grip_ranks","huxwrx-flow-556k.grip_first_x","huxwrx-flow-556k.grip_stagger","huxwrx-flow-556k.grip_pitch","huxwrx-flow-556k.grip_dash_length","huxwrx-flow-556k.grip_dash_width"]},"profiles":{"side":{"plane":"xy","origin":"the hex collar's rear face, on the axis","offset":{},"points":[[0,0.608],[0,0],[0,-0.61],[0.017,-0.636],[0.036,-0.642],[0.244,-0.642],[0.299,-0.653],[0.352,-0.673],[0.37,-0.692],[0.374,-0.702],[0.488,-0.757],[0.576,-0.79],[0.616,-0.799],[0.955,-0.801],[0.966,-0.792],[1.044,-0.792],[1.057,-0.801],[1.196,-0.801],[1.639,-0.792],[4.87,-0.792],[4.973,-0.775],[5.019,-0.761],[5.061,-0.742],[5.111,-0.699],[5.272,-0.494],[5.274,-0.388],[5.292,-0.355],[5.33,-0.316],[5.46,-0.226],[5.486,-0.196],[5.492,-0.174],[5.491,-0.131],[5.48,-0.125],[5.396,-0.125],[5.382,-0.11],[5.396,-0.096],[5.476,-0.043],[5.49,-0.02],[5.492,0.154],[5.479,0.207],[5.461,0.238],[5.331,0.408],[5.263,0.505],[5.107,0.703],[5.077,0.731],[5.028,0.757],[4.978,0.772],[4.883,0.79],[1.628,0.792],[1.118,0.801],[1.061,0.801],[1.046,0.792],[0.964,0.792],[0.951,0.801],[0.64,0.801],[0.572,0.788],[0.495,0.759],[0.376,0.702],[0.37,0.69],[0.354,0.673],[0.294,0.651],[0.226,0.64],[0.03,0.64],[0.007,0.626]],"scaleRefs":["huxwrx-flow-556k.length","huxwrx-flow-556k.od"],"inputs":{"huxwrx-flow-556k.length":5.5,"huxwrx-flow-556k.od":1.6},"tolerance":0.003,"photo":"references/huxwrx-flow-556k d9decdd1e19b (HUXWRX, FLOW 556k white paper: the side outline over its 5.5in / 14.0cm dimension line (the page at 600 dpi, 6600 x 5100))","method":"luminance < 128, inside [1780, 1020, 4330, 1790], closing ×3, largest piece, holes filled, inset 3 px (half the outline's stroke); scale from huxwrx-flow-556k.length = 5.5 in (x-extent 2492 px → 453.1 px/in) and huxwrx-flow-556k.od = 1.6 in (y-extent 727 px → 454.4 px/in), which agree within 0.3%; mean 453.7 px/in; origin at x min, y center of the outline; Douglas-Peucker at 0.003 in with the extremes kept: 64 points (IoU 0.998 with the full outline); checks: height (tooth tops, max over 0.4 in windows) along x [2.2, 4.4] 1.585 ± 0.007; height (tooth tops, max over 0.1 in windows) along x [0.03, 0.19] 1.283 ± 0.007 (tools/trace.py)","via":"harvest","note":"The mount end (the hex collar) at the rear, the cap at the front. A drawing's outline: the grip texture's dashes that fall on the edge stand on it, and the cap's slots that fall on the edge notch it; the model turns the body at its published diameter and cuts the slots itself."}},"gaps":[{"what":"The cap's pockets: their depth, their floors and how they open into the core","need":"a sharp photo straight on at the muzzle end of the 556K (the only one on file is of the 556 Ti) and one square from the side across the cap"},{"what":"The mount's socket: its thread, its taper and its depth","need":"the maker's drawing of the QD mount; it is drawn to fit the flash hider"},{"what":"Weight: 12.9 oz at the maker, 11.8 and 11.9 oz at two sellers","need":"a reviewer's own scale reading, or the maker's word on what the lighter figure is"},{"what":"How far the can's front stands ahead of the muzzle: the pair as drawn against the maker's 4.9 in","need":"a photo of the can on a rifle square from the side, with the barrel's shoulder in view"},{"what":"5.45 in the maker's list of calibers","need":"a name for it in data/cartridges.yaml"}]},"jp-silent-captured-spring-gen2-h2":{"id":"jp-silent-captured-spring-gen2-h2","name":"Silent Captured Spring AR-15 Heavy H2 GEN 2","manufacturer":"JP Enterprises","sku":"JPSCS2-15H2","url":"https://jprifles.com/buy_test.php?item=JPSCS2-15H2","category":"buffer","description":"A buffer and its spring held together on a guide rod as one unit, which takes the place of both in the receiver extension: JP's Silent Captured Spring with its H2 weights, two tungsten and one steel. The maker: \"Buffering/Reciprocating Mass: 4.8 oz. (Ideal for replacing a standard buffer of the same weight)\", and \"Recommended Use: Short-barreled rifles (SBRs) Suppressed weapons Rifles recommended to use an H2 buffer Select-fire rifles Piston-operated rifles\". It comes with a spacer for rifle-length extensions: \"Includes spacer to allow for installation in both carbine- and rifle-length buffer tubes.\"","weight":"jp-silent-captured-spring-gen2-h2.weight","occupies":["buffer_spring"],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"bore":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the unit's axis at the slider's front face (where the carrier bears on it, as a buffer's head), +x rearward toward the end cap."}},"interfaces":{"bore":{"type":"ar15.extension_bore","role":"buffer","anchor":"bore","params":{},"flips":false}},"materials":{"body":{"label":"Slider and end cap","finish":"anodized","recolorable":false,"color":"jp-scs-hard-anodize","note":"The slider's flange and collar and the end cap, a dark grey in Primary Arms' two photos of the H2 (references/jp-silent-captured-spring-gen2-h2 708eab533a4c, the flange's face #5d5b5e; 0c20449e5d5c), where its photo of the standard (0b290578345a) and MidwayUSA's have them black. JP: \"Slide (with exception to SLIDE5) and guide rod now in clear coat hard anodize\" (the text layer of its selection guide PDF), an undyed hard anodize whose tone is the lot's."},"tungsten":{"label":"Tungsten weights","finish":"steel","recolorable":false,"color":"jp-scs-tungsten","note":"The two front weights, tungsten (JP: \"2 Tungsten | 1 Steel (H2) 4.8 oz. JPSCS2-15H2\"): a matte cool grey in Primary Arms' photo from ahead (708eab533a4c, their lit band #7c7c87), against the bright steel one behind them."},"weights":{"label":"Steel weight","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"The rearmost weight, next to the collar: bright steel in Primary Arms' photo (708eab533a4c) and JP's own (c5a3ef37c597). Bright metal isn't fitted to a photo."},"orings":{"label":"O-rings","finish":"rubber","recolorable":false,"color":"placeholder-polymer-black","note":"Black rubber between the weights, as the standard's (708eab533a4c)."},"hardware":{"label":"Snap ring and screws","finish":"steel","recolorable":false,"color":"steel-phosphate-black","note":"The snap ring and the screw in each end, black in the photos (0c20449e5d5c has the rear screw in its pocket)."},"rod":{"label":"Guide rod","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"Aluminium (Wing Tactical's page for the standard and the H2: \"Material: Guide Rod: Aluminum\"), bright between the coils in 708eab533a4c."},"spring":{"label":"Spring","finish":"steel","recolorable":false,"color":"steel-phosphate-black","note":"JP's 15-100 (the kit sheet: \"JPSCS-15-100** Uncolored\", \"** JPSCS2-15H2\"): black along its whole length in both of Primary Arms' photos of the H2 (708eab533a4c, 0c20449e5d5c) and in JP's own (c5a3ef37c597). A black on steel isn't fitted to a photo."},"bumper":{"label":"Bumper","finish":"polymer","recolorable":false,"color":"jp-scs-bumper","note":"The same cream polymer as the standard's: the H2's photos (0c20449e5d5c) have it a pale cream."}},"components":{},"geometry":{"model":"jp-silent-captured-spring-gen2-h2.glb","components":{},"approximations":["The standard unit's shape, by its ledger's figures through expressions: no photo of the H2 is square to its side, and JP and its sellers state no size of it. What the H2's own photos give is its own: the front bore (708eab533a4c), the end cap's pocket and screw (0c20449e5d5c), and its spring's turns, 25 between the collar and the bumper (708eab533a4c levelled), against the standard's 30.5.","Its two front weights are drawn tungsten and the rearmost steel, as its photos have them; the tungsten weights are the steel ones' shape (JP's weights sheet swaps one for the other on the same slider).","Its spring is drawn at the standard's outside and wire (the H2's three-quarter photo reads its outside 4% under the standard's), at the pitch of its own 25 turns, running on inside the slider and the bumper as the standard's does.","Not drawn, as on the standard: the engraving on the end cap, the notch in its rim, the slider's inner shoulders, the rod's thread, the spacer and the shim."],"ledger":["jp-silent-captured-spring-gen2-h2.tungsten_count","jp-silent-captured-spring-gen2-h2.coils","jp-silent-captured-spring-gen2-h2.front_bore_d","jp-silent-captured-spring-gen2-h2.cap_pocket_d","jp-silent-captured-spring-gen2-h2.length","jp-silent-captured-spring-gen2-h2.od","jp-silent-captured-spring-gen2-h2.spring_od"]},"profiles":{},"gaps":[{"what":"A square side view of the H2","need":"A seller's side photo of this number (MidwayUSA's and Silencer Shop's pages have none on file): its spring's outside and wire, and any size that differs from the standard's"}]},"jp-silent-captured-spring-gen2-h3":{"id":"jp-silent-captured-spring-gen2-h3","name":"Silent Captured Spring AR-15 Heavy H3 GEN 2","manufacturer":"JP Enterprises","sku":"JPSCS2-15H3","url":"https://jprifles.com/buy_test.php?item=JPSCS2-15H3","category":"buffer","description":"A buffer and its spring held together on a guide rod as one unit, which takes the place of both in the receiver extension: JP's Silent Captured Spring with its H3 weights, all three tungsten. The maker: \"Buffering/Reciprocating Mass: 5.6 oz. (Ideal for replacing a standard buffer of the same weight)\", and \"The use case for an H3 SCS is virtually the same as the H2. In almost all cases, the two can be used interchangeably, and the choice between the two comes down to a preference in weight and cycling feel. The H2 is will produce a faster, snappier cycle compared to the H3, which will have a slower, heavier cycle. Only in extreme cases such as a severely over-gassed rifle without an adjustable gas block would the H3 be a functional recommendation over the H2.\"","weight":"jp-silent-captured-spring-gen2-h3.weight","occupies":["buffer_spring"],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"bore":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the unit's axis at the slider's front face (where the carrier bears on it, as a buffer's head), +x rearward toward the end cap."}},"interfaces":{"bore":{"type":"ar15.extension_bore","role":"buffer","anchor":"bore","params":{},"flips":false}},"materials":{"body":{"label":"Slider and end cap","finish":"anodized","recolorable":false,"color":"placeholder-black","note":"The standard's black: no photograph of the H3 is on file. JP's one picture of it (references/jp-silent-captured-spring-gen2-h3 5251098b70ce) is its picture of the H2 (c5a3ef37c597) with the steel weight darkened, the same silhouette to the pixel, and has the slider a dark bronze, as JP's pictures of the standard and the H2 do; MidwayUSA's and Primary Arms' photographs of the standard have it black."},"tungsten":{"label":"Tungsten weights","finish":"steel","recolorable":false,"color":"jp-scs-tungsten","note":"All three weights, tungsten (JP: \"3 Tungsten (H3) 5.6 oz. JPSCS2-15H3\"), drawn in the H2's tungsten as Primary Arms' photo of the H2 has it: JP's picture of the H3 is its H2 picture with the steel weight made the tungsten's grey."},"orings":{"label":"O-rings","finish":"rubber","recolorable":false,"color":"placeholder-polymer-black","note":"Black rubber between the weights, as the standard's and the H2's."},"hardware":{"label":"Snap ring and screws","finish":"steel","recolorable":false,"color":"steel-phosphate-black","note":"The snap ring and the screw in each end, as the standard's and the H2's."},"rod":{"label":"Guide rod","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"Aluminium, as the standard's and the H2's (Wing Tactical: \"Material: Guide Rod: Aluminum\")."},"spring":{"label":"Spring","finish":"steel","recolorable":false,"color":"steel-phosphate-black","note":"The H2's spring, black as JP's picture of the H3 (the H2's) has it: JP names no spring for the H3."},"bumper":{"label":"Bumper","finish":"polymer","recolorable":false,"color":"jp-scs-bumper","note":"The standard's cream polymer; JP's picture has it a cream."}},"components":{},"geometry":{"model":"jp-silent-captured-spring-gen2-h3.glb","components":{},"approximations":["The standard unit's shape, by its ledger's figures through expressions, and the H2's spring: no photograph of the H3 is on file (JP's one picture of it is its H2 picture recoloured), and JP states no size of it.","All three weights are drawn tungsten, the steel ones' shape (JP's weights sheet swaps one for the other on the same slider).","Not drawn, as on the standard: the engraving on the end cap, the notch in its rim, the slider's inner shoulders, the rod's thread, the spacer and the shim."],"ledger":["jp-silent-captured-spring-gen2-h3.tungsten_count","jp-silent-captured-spring-gen2-h3.length","jp-silent-captured-spring-gen2-h3.od","jp-silent-captured-spring-gen2-h3.coils"]},"profiles":{},"gaps":[{"what":"A photograph of the H3","need":"A seller's photo of this number: JP's own picture of it is its H2 picture with the steel weight darkened"},{"what":"A seller","need":"No seller in data/vendors.yaml carries JPSCS2-15H3 (web search, 2026-10-18); JP's own store sells it ($233.95 on its page) and its page carries no offer markup"}]},"jp-silent-captured-spring-gen2":{"id":"jp-silent-captured-spring-gen2","name":"Silent Captured Spring AR-15 Standard GEN 2","manufacturer":"JP Enterprises","sku":"JPSCS2-15","url":"https://jprifles.com/buy_test.php?item=JPSCS2-15","category":"buffer","description":"A buffer and its spring held together on a guide rod as one unit, which takes the place of both in the receiver extension. The maker: \"Maintaining all the benefits of our polished buffer springs and proprietary LMOS™ buffer, this combination buffer-spring assembly eliminates the friction of standard buffer components resulting in outstanding smoothness and sound abatement.\" \"Even in a very rough extension tube, the rifle runs smooth since the spring never contacts the tube, running instead on a guide rod similar to a 1911 guide rod system.\" This is the standard weight: three steel weights, \"Buffering/Reciprocating Mass: 2.9 oz. (Ideal for replacing a standard buffer of the same weight)\". It comes with a spacer for rifle-length extensions: \"Includes spacer to allow for installation in both carbine- and rifle-length buffer tubes.\" The maker recommends taking the buffer retainer out: \"Because the insertion and removal of the Silent Captured Spring is very difficult with a standard buffer retainer pin, we recommend removing it when installing your SCS.\"","weight":"jp-silent-captured-spring-gen2.weight","occupies":["buffer_spring"],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"bore":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the unit's axis at the slider's front face (where the carrier bears on it, as a buffer's head), +x rearward toward the end cap."}},"interfaces":{"bore":{"type":"ar15.extension_bore","role":"buffer","anchor":"bore","params":{},"flips":false}},"materials":{"body":{"label":"Slider and end cap","finish":"anodized","recolorable":false,"color":"placeholder-black","note":"The slider's front flange and rear collar, and the end cap behind the bumper: black in every photo of the GEN 2 (MidwayUSA's 3431b2d79bca, Primary Arms' 708eab533a4c and 0c20449e5d5c). Anodized aluminium by JP's own word on the front of the unit, in its Law folder sheet: \"you may notice surface wear on the Silent Captured Spring unit where it contacts the bolt carrier extension. This is normal cosmetic wear to the anodizing\" (https://jprifles.com/document_pdfs/JPSCS2LAW_808.pdf). The text layer of JP's selection guide PDF (an earlier media sheet under its pages, not shown on them): \"Slide (with exception to SLIDE5) and guide rod now in clear coat hard anodize for a new look and enhanced asthetics\": an undyed hard anodize, which comes out a near black on these parts in every photo. The end cap is drawn in aluminium too: in the patent's steel the unit's metal alone would outweigh JP's 5.3 oz."},"weights":{"label":"Weights","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"Three steel weights (JP: \"3 Steel 2.9 oz. JPSCS2-15\"), turned bright in MidwayUSA's photo of the standard unit (3431b2d79bca). Bright metal isn't fitted to a photo: the app's natural steel. The H2's two tungsten weights are a dark grey (708eab533a4c): another part."},"orings":{"label":"O-rings","finish":"rubber","recolorable":false,"color":"placeholder-polymer-black","note":"Black rubber, one either side of each weight but the rearmost's back (JP's weights sheet: \"One O-ring should be positioned on every side of the weights except in the space between the weight and the snap ring.\")."},"hardware":{"label":"Snap ring and screws","finish":"steel","recolorable":false,"color":"steel-phosphate-black","note":"The snap ring behind the rearmost weight and the screw in each end, black in the photos (3431b2d79bca, 0c20449e5d5c). JP names no finish."},"rod":{"label":"Guide rod","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"Aluminium (Wing Tactical: \"Material: Guide Rod: Aluminum\"), a bright satin grey in MidwayUSA's photo (3431b2d79bca, #aba39e to #b8b4b5 on its lit flank, the same as the weights beside it): bright metal, drawn as the weights are."},"spring":{"label":"Spring","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"JP's \"15-85\" spring (\"The AR-15 models comes with a 15-85 spring\"), bright in the standard unit's photo (3431b2d79bca); Primary Arms: \"Centerless-ground, precision-polished spring\". The H2's is black in its photos (708eab533a4c)."},"bumper":{"label":"Bumper","finish":"polymer","recolorable":false,"color":"jp-scs-bumper","note":"A pale cream polymer in the photos of the GEN 2 (MidwayUSA's 3431b2d79bca, Primary Arms' 0c20449e5d5c); a yellower urethane in Wing Tactical's photos (26c0d1ee43a2), which are of another production run (its flange bright, no O-rings showing)."}},"components":{},"geometry":{"model":"jp-silent-captured-spring-gen2.glb","components":{},"approximations":["Every size but the length and the hex key is read on one straight side photo of the standard unit (MidwayUSA's), scaled by the unit's length out of the rifle, which is worked out from JP's protrusion figure and the standard carbine extension's room; one seller's 7 in agrees. The front bore and the rear pocket are read on Primary Arms' two photos of the H2, whose slider and end cap are the standard's.","Drawn as installed, bolt forward: the end cap on the extension's rear wall and the slider's front face where a buffer's head is, 0.023 in further back along its rod than out of the rifle (JP's .030 protrusion past the lower's face, less the 0.007 between that face and an upper's).","The slider is drawn as a black aluminium body (front flange, a tube under the weights, rear collar) carrying three steel rings with an O-ring band before and between them and a snap ring behind the last, and inside it the maker's patent's bores: the front bore the front screw's head sits in, an inner flange it bears on (its thickness assumed), and a central bore behind that which the spring's front end goes into (its diameter assumed, the spring's and a clearance). The weights' bore is taken to be the tube whose rear end is the collar seen behind the snap ring. So drawn, the slider weighs 2.93 oz as aluminium and steel, JP's 2.9 oz buffering mass within 1%.","The bumper is bored for the spring's rear end to a ledge half way along it, and the end cap's spigot fills its rear half to the cap's flange, bored for the spring (the patent: \"a ledge 64 at a point approximately midway between the front and the rear\"; the spigot's diameter assumed). The cap is drawn black anodized aluminium: the patent's first generation had it in steel, and in steel the unit's metal alone would weigh more than JP's 5.3 oz; in aluminium it leaves 0.28 oz for the bumper and the O-rings, a urethane's weight for their size.","The spring is a round wire on a helix (lib.coil_x), at the pitch of the 30.5 turns counted where it shows between the collar and the bumper on Primary Arms' photo, and runs on at that pitch, out of sight, from the slider's inner flange to the bottom of the end cap's bore (the patent: \"The front 54 of the spring abuts the flange 36 of the slider, and the rear 56 of the spring abuts the rear of the central bore 84 in the end cap.\"), 55 turns in all; drawn bright as MidwayUSA's photo has it, not with the black colour code at one end that Primary Arms' has. The guide rod runs from the screw at the bottom of the slider's front bore to the end cap.","The bumper is a cone of the two diameters read at its ends, its front edge rounded; the end cap a disc of the cap's diameter with its rear edge rounded and a pocket in its face holding the rear screw's head with a 1/8 in hex socket.","Not drawn: the words engraved on the end cap (\"US 8,800,424\"), the notch in its rim, the spring's colour code, the slider's inner shoulders and the rod's thread; the rifle-length spacer and the shim, which go behind the unit only in a rifle-length tube."],"ledger":["jp-silent-captured-spring-gen2.length","jp-silent-captured-spring-gen2.installed_length","jp-silent-captured-spring-gen2.od","jp-silent-captured-spring-gen2.flange_d","jp-silent-captured-spring-gen2.flange_length","jp-silent-captured-spring-gen2.mass_length","jp-silent-captured-spring-gen2.oring_gap","jp-silent-captured-spring-gen2.collar_d","jp-silent-captured-spring-gen2.rod_d","jp-silent-captured-spring-gen2.spring_od","jp-silent-captured-spring-gen2.wire_d","jp-silent-captured-spring-gen2.coils","jp-silent-captured-spring-gen2.bumper_length","jp-silent-captured-spring-gen2.bumper_rear_d","jp-silent-captured-spring-gen2.bumper_front_d","jp-silent-captured-spring-gen2.cap_d","jp-silent-captured-spring-gen2.cap_length"]},"profiles":{},"gaps":[{"what":"The maker's own sizes","need":"JP publishes no length or diameter of the unit: a drawing or a measured review would replace the photo readings (every diameter is one photo's, ±1.6%)"},{"what":"The weights' bore and the slider's tube","need":"A photo of the slider taken apart (JP's weights sheet describes it, and shows none on file): the model's are assumed for the weight"}]},"kynshot-rb5000":{"id":"kynshot-rb5000","name":"RB5000","manufacturer":"KynSHOT","sku":"RB5000","url":"https://www.kynshot.com/products/our-products/kynshot-rb5000-9/","category":"buffer","description":"A hydraulic buffer: a sealed damper in a stainless body, its piston rod carrying the head the bolt carrier meets, used in place of a solid weighted buffer with the rifle's own spring. KynSHOT: \"The KynSHOT RB5000 is a hydraulic recoil buffer engineered for AR-15 platforms with a Mil-Spec carbine buffer tube (7” internal depth). The RB5000 works with any Mil-Spec buffer spring and installs easily as a direct drop-in replacement for existing buffer systems.\" \"Using patented technology, the RB5000 absorbs the recoil energy generated by the bolt carrier’s rearward movement, helping to eliminate bolt bounce during chambering.\" At rest it is 3.65 in long and pushed in 3.25, a standard carbine buffer's length: all4shooters, \"The Kynshot, when extended, is longer than a standard buffer, and pulling back the bolt will result in the buffer contacting the rear end of the buffer tube too soon\". The maker: \"DO NOT USE IN PCC's.\"","weight":"kynshot-rb5000.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"bore":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the buffer's axis at its head's front face, +x rearward (toward its bumper)."}},"interfaces":{"bore":{"type":"ar15.extension_bore","role":"buffer","anchor":"bore","params":{},"flips":false}},"materials":{"body":{"label":"Body and head","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"KynSHOT: \"Manufactured with a high strength 17-4 stainless steel construction throughout\" (MidwayUSA: \"Material 1704 Stainless Steel\"). Bright bare stainless in every photo, satin in the maker's own (823ba35382b7), polished in MidwayUSA's (ef0c90ef9af5): bright metal isn't fitted to a photo, it is the app's natural stainless. The head, the hub and the body are one look in every photo."},"rod":{"label":"Piston rod","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"Polished, brighter than the body in MidwayUSA's and Impact Guns' photos (a mirror line along it): the 17-4 the maker says it is built of throughout."},"bumper":{"label":"Bumper","finish":"rubber","recolorable":false,"color":"placeholder-polymer-black","note":"Black in every photo, a matte rubber; sold alone as a part (Impact Guns lists \"Kynshot Replacement Rubber Bumper FOR AR Recoil Buffers\"). A black isn't fitted: the catalog's polymer black, under rubber."},"screw":{"label":"Set screw","finish":"steel","recolorable":false,"color":"placeholder-black","note":"A dark socket set screw in the hole across the hub (the RB5000HP's side photo, 3bf8c2301cf9, shows its socket; the RB5000's photos show the holes, threaded). Not fitted: the catalog's placeholder black."},"seal":{"label":"Seal","finish":"rubber","recolorable":false,"color":"placeholder-polymer-black","note":"The dark seal the rod comes out of, inside the body's mouth (Impact Guns' views from above); a black isn't fitted."}},"components":{},"geometry":{"model":"kynshot-rb5000.glb","components":{},"approximations":["Drawn at rest, its rod out (3.65 in), as it stands in a rifle with the bolt forward; pushed in (3.25) it isn't drawn.","Its sizes other than the maker's four (length at rest and pushed in, the body's .69 in, the weight) are read on MidwayUSA's photo of it, scaled by the maker's length along the axis and by the body's diameter across: the head, the hub, the rod and the bumper each to about 0.015 in.","The head's three flats: two are seen at once in the one view of the head from above (Impact Guns), as far round as each other from the lens; the third, behind, is what equal spacing gives. Where they stand round the axis is a pose: one is drawn at the top.","The body is drawn solid behind its mouth: it is a sealed damper, hollow and holding fluid (\"Manufactured with Mil-Spec hydraulic fluids and seals\"), which is why the model, as solid steel, weighs more than the maker's 4.2 oz. How big its bore is isn't on file.","The body's mouth: a thin wall round a bore, with the seal a little way inside (the wall and the depth are assumed, said in the ledger); the ring that holds the seal is drawn as part of the body.","The set screw in the hub's hole on the rifle's right, a little below the surface, with a hex socket in its end: how far it is sunk and its socket's size and depth are assumed (the ledger says so); the hole on the left is drawn empty, as the photos from above show one.","Not drawn: the engraving (the maker's name and mark, \"P/N RB5000\", a batch number and \"PATENT NO. US 10,100,896 B2\"); the earlier head, with a screw in the middle of its face, of Primary Arms' and AR15Discounts' photo (\"BB5012\") and Armory Blog's (2014)."],"ledger":["kynshot-rb5000.length","kynshot-rb5000.od","kynshot-rb5000.head_d","kynshot-rb5000.head_thickness","kynshot-rb5000.hub_d","kynshot-rb5000.rod_d","kynshot-rb5000.rod_exposed","kynshot-rb5000.body_length","kynshot-rb5000.bumper_exposed"]},"profiles":{},"gaps":[{"what":"The head's flats seen face-on","need":"a view looking along the axis at the head's face, to count the flats round the whole turn and read their depth square (two are seen at once from above)"},{"what":"What it is inside","need":"the body's bore and the damper's parts: the maker's patent US 10,100,896 B2 (engraved on the part) draws its mechanism, not this product's sizes; nothing is drawn of the inside"},{"what":"Its stroke against its rod","need":"a photo of it pushed in, or the maker's word: the rod stands out 0.32 in at rest, and the maker's two lengths differ by 0.40"}]},"kynshot-rb5000hp":{"id":"kynshot-rb5000hp","name":"RB5000HP (High Performance)","manufacturer":"KynSHOT","sku":"RB5000HP","url":"https://www.kynshot.com/products/our-products/kynshot-rb5000hp-high-performance-96/","category":"buffer","description":"A hydraulic buffer made to damp more than the RB5000, for rifles that cycle hard. KynSHOT: \"The KynSHOT RB5000HP is a hydraulic recoil buffer engineered for over-gassed AR-15 platforms and 9mm radial delayed blowback systems. The RB5000HP is optimized for use with Mil-Spec carbine buffer tubes (7” internal depth), and works with any standard buffer spring.\" \"When a suppressor is added to an AR-15, increased back pressure often results in harsher cycling. The RB5000HP builds on the performance of the RB5000 with enhanced damping to better manage this added pressure.\" At rest it is 3.69 in long and pushed in 3.25, a standard carbine buffer's length. The maker: \"DO NOT USE IN DIRECT BLOWBACK PCC's.\"","weight":"kynshot-rb5000hp.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"bore":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the buffer's axis at its head's front face, +x rearward (toward its bumper)."}},"interfaces":{"bore":{"type":"ar15.extension_bore","role":"buffer","anchor":"bore","params":{},"flips":false}},"materials":{"body":{"label":"Body and head","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"KynSHOT: \"Manufactured with high strength 17-4 stainless steel construction throughout\" (MidwayUSA: \"Material 17-4 PH Stainless Steel\"). Bright bare stainless in every photo, satin in the maker's own (57086653f522) and Impact Guns', polished in AR15Discounts' (3bf8c2301cf9): bright metal isn't fitted to a photo, it is the app's natural stainless."},"rod":{"label":"Piston rod","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"Polished, a mirror line along it in the side photo (3bf8c2301cf9): the 17-4 the maker says it is built of throughout."},"bumper":{"label":"Bumper","finish":"rubber","recolorable":false,"color":"placeholder-polymer-black","note":"Black in every photo, a matte rubber. A black isn't fitted: the catalog's polymer black, under rubber."},"screw":{"label":"Set screw","finish":"steel","recolorable":false,"color":"placeholder-black","note":"A dark socket set screw in the hole across the hub, its socket seen in the side photo (3bf8c2301cf9). Not fitted: the catalog's placeholder black."},"seal":{"label":"Seal","finish":"rubber","recolorable":false,"color":"placeholder-polymer-black","note":"The dark seal the rod comes out of, inside the body's mouth (Impact Guns' view from above, 270a10eca7ff); a black isn't fitted."}},"components":{},"geometry":{"model":"kynshot-rb5000hp.glb","components":{},"approximations":["Drawn at rest, its rod out (3.69 in), as it stands in a rifle with the bolt forward; pushed in (3.25) it isn't drawn.","Its sizes other than the maker's four (length at rest and pushed in, the body's .76 in, the weight) are read on AR15Discounts' level side photo of it, scaled by the maker's length along the axis and by the body's diameter across: the head, the hub, the rod and the bumper each to about 0.015 in.","The head's three flats: two are seen at once in Impact Guns' view of the head from above; the third, behind, is what equal spacing gives. Where they stand round the axis is a pose: one is drawn at the top.","The body is drawn solid behind its mouth: it is a sealed damper, hollow and holding fluid, which is why the model, as solid steel, weighs more than the maker's 4.8 oz. How big its bore is isn't on file.","The body's mouth: a thin wall round a bore, with the seal a little way inside (the wall and the depth are assumed, said in the ledger); the ring that holds the seal is drawn as part of the body.","The set screw in the hub's hole on the rifle's right, a little below the surface, with a hex socket in its end: how far it is sunk and its socket's size and depth are assumed (the ledger says so); the hole on the left is drawn empty, as the photos from above show one.","Not drawn: the engraving (the maker's name and mark, \"P/N: RB5000HP\", a batch number and \"PATENT NO: US 10,100,896 B2\")."],"ledger":["kynshot-rb5000hp.length","kynshot-rb5000hp.od","kynshot-rb5000hp.head_d","kynshot-rb5000hp.head_thickness","kynshot-rb5000hp.hub_d","kynshot-rb5000hp.rod_d","kynshot-rb5000hp.rod_exposed","kynshot-rb5000hp.body_length","kynshot-rb5000hp.bumper_exposed"]},"profiles":{},"gaps":[{"what":"The head's flats seen face-on","need":"a view looking along the axis at the head's face, to count the flats round the whole turn and read their depth square"},{"what":"What it is inside","need":"the body's bore and the damper's parts: nothing is drawn of the inside"},{"what":"Its stroke against its rod","need":"a photo of it pushed in, or the maker's word: the rod stands out 0.33 in at rest, and the maker's two lengths differ by 0.44"},{"what":"A review of its own","need":"the reviews on file (all4shooters, Armory Blog) are of the RB5000"}]},"larue-mbt-2s":{"id":"larue-mbt-2s","name":"MBT-2S trigger, straight","manufacturer":"LaRue Tactical","sku":"LT-MBT-2SSB","category":"trigger","weight":"larue-mbt-2s.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"fcg":{"origin":[0,0,0],"note":"Trigger frame: origin on the trigger pin axis."},"face":{"origin":["{.face_offset_x}",0,0],"note":"The shoe's face, where length of pull is measured from (its front edge at the exposed blade's mid-height)."}},"interfaces":{"fcg":{"type":"ar15.fcg","role":"trigger","anchor":"fcg","params":{"pin_diameter":"small-pin"},"flips":false}},"materials":{"shoe":{"label":"Trigger shoe","finish":"steel","recolorable":false,"color":"placeholder-black","note":"S7 tool steel, \"Black\" (LaRue, https://larue.com/mbt-2-stage-ar-triggers-mc7h/); the finish's process isn't stated, and it is sold in the one finish (the straight bow is LTMBT-2S-SB). A satin black with the machining showing and a bright line on its edges, on Primary Arms' side view (1857b5884377) and on the user's own (282e8449a1d8, 0e58651de32a): a black on machined steel, not fitted to a photo. On the set as sold the hammer and the disconnector are the same black and the springs bare steel wire: none is drawn (the trigger alone is)."}},"components":{"shoe":{"label":"Trigger","material":"shoe"}},"geometry":{"model":"larue-mbt-2s.glb","components":{},"approximations":["The trigger alone is drawn, in the round since 2026-10-05: LaRue's side outline (scaled by its pin's hole) at the widths read on the user's own trigger. Its body is 0.30 in thick, its bow as wide as the thread's caliper has it (0.305; the user's photos read 0.295 ± 0.012), with the chamfer down each side of its flat face carried round its tip and back (the face's alone is seen; drawn at 45°); its bosses plain rounds 0.68 in end to end. The hammer, the disconnector, the springs and the two pins are inside the receiver and aren't drawn.","The body is whole where the real one is not: the window through it behind the pin, the slot in its top the disconnector lies in (about six tenths of the body across), the adjustment screw by the front hook and the groove let into each side of the bow are in the user's photos and not in the model. The outline carries the trigger spring's wire in one place ahead of the pin.","At rest as LaRue photographed it (the photo's tail edge taken as level): no photo of it in a lower with the pins in frame is on file."],"ledger":["larue-mbt-2s.face_offset_x","larue-mbt-2s.shoe_face_x"]},"profiles":{"side":{"plane":"xy","origin":"centre of the trigger pin hole (the trigger frame origin); tail edge level as in the photo","offset":{},"points":[[-1.161,-0.126],[-1.154,-0.252],[-1.09,-0.283],[-1.005,-0.26],[-0.052,-0.258],[-0.049,-0.475],[-0.108,-0.755],[-0.101,-0.969],[-0.009,-1.278],[0.053,-1.387],[0.098,-1.399],[0.132,-1.364],[0.116,-0.554],[0.233,-0.411],[0.462,-0.344],[0.462,-0.288],[0.508,-0.271],[0.462,-0.232],[0.463,-0.151],[0.718,-0.133],[0.738,0.071],[0.404,0.076],[0.328,0.102],[0.271,0.186],[0.264,0.367],[0.182,0.509],[0.131,0.527],[0.04,0.4],[0.042,0.362],[0.126,0.354],[0.119,0.259],[0.065,0.168],[-0.363,0.191],[-0.374,0.252],[-0.335,0.282],[-0.318,0.354],[-0.341,0.466],[-0.416,0.497],[-0.47,0.453],[-0.496,0.242],[-0.527,0.208],[-0.705,0.224],[-0.735,0.333],[-0.857,0.333],[-0.885,0.068],[-0.922,0.033],[-1.146,0.02]],"scaleRefs":["larue-mbt-2s.pin_diameter"],"inputs":{"larue-mbt-2s.pin_diameter":0.154},"tolerance":0.02,"photo":"references/larue-mbt-2s 45e00d2ce552 (LaRue MBT-2S-SB side view on white; supplied in chat, source not recorded)","method":"luminance < 150, pieces ≥ 2000 px, closing 7 px ×2, largest piece, holes filled; scale from the hole at (421.3, 249.6): 46.8 px across (circle through the 50% edge; 46.2–48.0 px at 65–35%) = larue-mbt-2s.pin_diameter 0.154 in → 303.8 px/in (the hole is taken as the pin's size; its running clearance is unsourced, and each 0.001 in of it would enlarge the outline 0.65%); origin at the hole's centre; Douglas-Peucker at 0.02 in with the extremes kept: 47 points (IoU 0.972 with the full outline); the spring wire bridged by the 7 px closing (tools/trace.py)","via":"user","note":"The body sits inside the lower (hidden in the render); the blade below the trigger opening is what shows. The hammer is a separate part and isn't drawn."}},"gaps":[{"what":"Where it rests in a lower: the outline is as LaRue's photo has it, its tail taken as level","need":"The user's own, in the lower, from the side and square on, both pins in frame"},{"what":"Its side outline from the user's own trigger: theirs is in a corner of its photo and cut by the frame's edge, so LaRue's product photo is still the outline, and its scale is the pin's hole taken as the pin's size","need":"The trigger lying on its side in the middle of the frame, from 3 ft or more, zoomed, a ruler lying beside it on something as thick as the trigger"},{"what":"The window through the body, the disconnector and its slot, the adjustment screw, the bow's side grooves","need":"Nothing more for their places (282e8449a1d8 and 70c0dd8b895c have them): a pass on the model, with the side view above for their sizes"},{"what":"The hammer, its spring and the two pins","need":"The hammer from its side with a ruler beside it (b6661e28ee95 is edge on): for the exploded view"}]},"law-tactical-gen-s-folder":{"id":"law-tactical-gen-s-folder","name":"AR Folding Stock Adapter GEN-S","manufacturer":"Law Tactical","sku":"99312","url":"https://www.lawtactical.com/ar_folding_stock_adapter_gen_3_m_p/99312.htm","category":"folding_adapter","description":"A hinge between the lower receiver and the buffer tube: press its button and the tube and stock swing to the rifle's left; unfolded they lock straight again. It moves the tube back 1.3 in, and a bolt carrier extension in the carrier's tail makes up the length. Law Tactical: \"Combining all of the proven features of the Gen 3-M with Stronger, Lighter, Smaller and Stainless Steel design\", \"17-4 Stainless Steel Housing ... DLC Coated\"; its instructions: \"Always close stock (unfold) before firing. The AR is not designed to be fired from the folded position.\"","weight":"law-tactical-gen-s-folder.weight","occupies":[],"integral":[],"brings":[],"seats":{"receiver_extension":{"parentInterface":"tube_socket","interface":"receiver_thread","folds":true,"note":"Law Tactical's GEN-S instructions, step 4: \"Then install the Buffer Tube and stock onto the Hinge Assembly (1A) in the same manner it would be installed onto the rear of the rifle receiver.\" The end plate and castle nut go on as they would on a receiver, against the stock half's rear face; the buffer and its spring stay in the tube, held by the retaining pin when folded (step 5), \"Standard Buffer Retaining Pin and Spring (not included)\" (step 4's drawing)."}},"requires":[],"folding":{"anchor":"hinge","moves":"stock_half","max":"law-tactical-gen-s-folder.fold_max","side":"left","inside":["carrier_extension"],"note":"Folds to the rifle's left: no page says it in words. Primary Arms' photo of it folded open from behind (430116178_01) has the stock half to the left of the receiver half, whose button stands out of its right side; the GEN-S instructions' cover draws a braced rifle from its left (the muzzle to the left) with the brace folded across the near side, and the data sheet's drawing the same. The instructions: \"To avoid accidental firing in the folded position, the SAFETY should ALWAYS be ENGAGED BEFORE FOLDING stock and should REMAIN ENGAGED until stock is unfolded.\""},"anchors":{"receiver_thread":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the tube axis at the takedown pin's X, +x rearward (+z is then the rifle's left). The threaded flange screws into the lower here as a tube would."},"tube_socket":{"origin":["{.added_length}",0,0],"x":[1,0,0],"note":"Where a receiver extension's own frame stands with the adapter on: the takedown pin's X moved back by the adapter's length. The stock half's rear face is the lower's rear face moved back as far."},"hinge":{"origin":["{.hinge_x}",0,"{.hinge_z}"],"x":[1,0,0],"y":[0,1,0],"note":"On the hinge bolt's axis, upright, low on the rifle's left (the knuckles from 0.16 in under the tube's axis down to the knurled nut), in the plane where the two halves meet."}},"interfaces":{"receiver_thread":{"type":"ar15.buffer_tube_mount","role":"tube","anchor":"receiver_thread","params":{},"flips":false},"tube_socket":{"type":"ar15.buffer_tube_mount","role":"receiver","anchor":"tube_socket","params":{},"flips":false}},"materials":{"body":{"label":"Adapter","finish":"nitride","recolorable":false,"color":"steel-nitride-black","options":{"black":{"label":"Black","finish":"nitride","color":"steel-nitride-black","sku":"99312","source":"https://www.lawtactical.com/ar_folding_stock_adapter_gen_3_m_p/99312.htm"}},"default":"black","note":"The two halves and their three knuckles. Law Tactical: \"CNC Machined 17-4 Steel\", \"DLC Coated\" (the page), \"17-4 Stainless Steel Housing ... DLC Coated\" (the data sheet): the catalog has no finish type for a diamond-like carbon coat, and the black is drawn as the nearest it has, a smooth black on steel (nitride, as the Gen 3-M's and SureFire's DLC parts are), not fitted to a photo. Black is the one colour the pages on file sell it in (Primary Arms' \"Gen S - Black\", AR15Discounts' \"Gen S - Black - OEM\"); the maker's page names none, and an FDE one seen only in a related-items thumbnail at AR15Discounts by the discovery isn't offered (no page or photo of it on file). Piece by piece (Primary Arms' three photos): the halves, the knuckles and the locking lug are the coat's black; the washers between the knuckles, the knurled nut, the hinge bolt's head, the button's bar, the latch, the threaded flange and the bolt carrier extension are a darker, glossier black (the hardware)."},"hardware":{"label":"Button, flange and hardware","finish":"nitride","recolorable":false,"color":"steel-nitride-black","note":"The washers between the knuckles, the hinge bolt's knurled nut and socket head, the button's bar out of the right side, the threaded flange and the bolt carrier extension: black in every photo. Steel (\"Stainless Steel Hardware and Springs\", the data sheet); a black on steel isn't fitted to a photo."}},"components":{},"geometry":{"components":{"receiver_half":"law-tactical-gen-s-folder.receiver_half.glb","stock_half":"law-tactical-gen-s-folder.stock_half.glb","carrier_extension":"law-tactical-gen-s-folder.carrier_extension.glb"},"approximations":["Each half is its end outline run its length: the outlines are traced from Primary Arms' photo of the part folded open 180 degrees from straight above (both mating faces to the lens), scaled by the stock half's threaded bore; the faces are taken as flat and the sides as straight along the bore, as the photos from behind and in three-quarter show them. The outline is the mating face's: whatever the halves have that differs toward their outer faces isn't seen (the receiver half's outer face's index pad and its side plate cover, the stock half's ring's raised rim).","The hinge's axis is half the housing's length behind the lower's rear face and the halves meet in its plane: read from how the part lies folded open on a table (each half flat on its outer face, the axis level between them) and from the two mating faces lying in one plane in that pose. No square side view is on file.","The hinge: an upright bolt low on the rifle's left, its two outer knuckles the stock half's and its middle one the receiver half's (US 8,769,855, the number engraved on the part: \"a hinged joint comprised of a hinge pivot 138 and two hinge tabs 134 joined by a hinge pin 139\"), black washers between them and the knurled nut under them, each at the height and size Primary Arms' photo has it (the nut is drawn with the stock half, whose lower tab it bears on: it turns about its own axis). Each knuckle is a plain round about the axis, joined to its half by the half's own outline. The hinge bolt's socket head sits in a counterbore in the upper tab's top (its size, how far it is sunk, its height and its socket's depth are assumed; its 1/8 in hex socket is the instructions' key); the bolt's shank inside the knuckles isn't drawn. Each half is cut clear of the other's knuckles.","The stock half's threaded bore is a 1 3/16-16 thread (lib.thread_x, a helix) between the extension's major diameter and its thread's crests as read; the receiver half's bore is the flange's lip, as read, through. The threaded flange is drawn in it: its thread the extension's, from the lower's rear face forward to where a tube's front face stands (std.receiver_extension.front_face_x), its bore the tube's (what the carrier runs in), its head in a counterbore at the receiver half's rear (assumed sizes: the ledger's flange_head_*); the flange's four tool cut-outs and its set screw aren't drawn.","On the stock half's front face its locking lug, low on the side away from the hinge, goes into the window in the receiver half's rear face where the latch catches it: the lug's face and the window's are read, how far the lug stands and the window's depth are assumed (the ledger). The window is drawn as a rounded rectangle at its read size; its side toward the button leans in (0.32 in across at its top, 0.26 at its bottom), which isn't drawn. The button is a black bar out of the receiver half's right side at the height read, in the middle of the half's length (where along it isn't read); its slot, spring and side plate cover aren't drawn, nor the latch's hook inside the receiver half's bore (drawn as it is unfolded: inside its slot).","The stock half's rear face has its three holes (two small, and the sling's quick-detach socket below them), blind, as deep as assumed; their places and sizes are read on Primary Arms' photo from behind and above with the face's foreshortening taken out, good to about a twentieth of an inch. The socket's ring and detent inside aren't drawn.","The bolt carrier extension is turned from Primary Arms' photo of it standing, scaled so that what stands behind its first shoulder is the 1.3 in it makes up (its lengths read 15 degrees foreshortened, its widths not): it lies in the carrier's tail with its first shoulder on the tail's rear end, where the carrier stands in battery (std.ar15.upper_rear_face_x), and reaches back to where the buffer then rests. At this scale its steel is 1.92 oz, the maker's 2 oz, and its end in the carrier 0.572 across, under the carrier's .625 bore (the ledger's ext_pilot_d says what that leaves open). Its O-rings and that end are inside the carrier and drawn plain.","Its weight is the maker's 7.4 oz for the housing and 2 oz for the extension. The model's steel (its two halves with the flange, washers, nut and bolt head: 2.76 cubic inches at std.density.steel; 17-4 is within a percent of it) weighs 12.6 oz, 1.70 times the housing's figure, as the Gen 3-M's model is 1.69 times its own: the halves are drawn solid where the photos show faces, and whatever pockets the real part has inside (the button's slot, its spring and cover, the latch's room behind the window, and more not seen) aren't drawn. The extension's (0.420 cubic inches, 1.92 oz) is the maker's 2 oz.","Not drawn: the engraving (\"PAT. 8769855 MADE IN USA NSN: 1005016724614\", \"CLOSE BEFORE FIRING\", the logo on the stock half's side), the set screws (the flange's, and the cover's), the faces' small chamfers beyond a 0.012 in break, the arc of raised rim on the stock half's mating face, the hole in the stock half's underside (Wilson Combat's photo from in front and below) and the one in the receiver half's foot, the receiver half's front face's index protrusion (it would stand in the lower's own metal, which the lowers on file don't have cut)."],"ledger":["law-tactical-gen-s-folder.added_length","law-tactical-gen-s-folder.hinge_x","law-tactical-gen-s-folder.hinge_z","law-tactical-gen-s-folder.length","law-tactical-gen-s-folder.width","law-tactical-gen-s-folder.height"]},"profiles":{"end_receiver":{"plane":"zy","origin":"the tube's axis (the half's own bore's centre in the photo)","offset":{},"points":[[-0.5206,0.5126],[-0.4378,0.5715],[-0.3255,0.6291],[-0.1374,0.6782],[-0.0055,0.6866],[0.104,0.681],[0.2093,0.6628],[0.33,0.6221],[0.4114,0.5799],[0.5082,0.5112],[0.5882,0.434],[0.657,0.3441],[0.7272,0.2052],[0.7356,0.1098],[0.7496,0.0971],[0.7637,0.0087],[0.7931,-0.0376],[0.8367,-0.0811],[0.831,-0.0867],[0.8423,-0.1092],[0.8451,-0.1752],[0.8675,-0.1808],[0.8928,-0.1695],[1.0809,-0.1611],[1.0809,-1.2896],[0.904,-1.2896],[0.8409,-1.2798],[0.824,-1.2615],[0.7875,-1.2741],[0.4198,-1.2812],[0.3594,-1.2938],[0.3216,-1.3148],[0.2893,-1.3485],[0.2696,-1.3934],[0.2584,-1.4861],[0.2275,-1.5141],[-0.1893,-1.5198],[-0.2188,-1.4987],[-0.2497,-1.437],[-0.2862,-1.3977],[-0.3339,-1.3696],[-0.4027,-1.3471],[-0.435,-1.3191],[-0.4855,-1.2461],[-0.5318,-1.152],[-0.5922,-1.1085],[-0.6736,-1.0889],[-0.7185,-1.058],[-0.7508,-1.0552],[-0.7508,-0.7815],[-0.7437,-0.7604],[-0.7522,-0.3674],[-0.7943,-0.1555],[-0.7901,0.034],[-0.7592,0.1645],[-0.6946,0.3077],[-0.623,0.4101]],"scaleRefs":["law-tactical-gen-s-folder.bore_thread_crest_d"],"inputs":{"law-tactical-gen-s-folder.bore_thread_crest_d":1.1568},"tolerance":0.006,"photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: the black GEN-S folded open 180 degrees on white, both mating faces up, from straight above; 5000 x 5000)","method":"The receiver half's mating face, seen from behind (its z is minus the photo's column less the bore's centre, 3141.1, over 712.5 px/in, in the picture turned back 2.28 degrees). The button's bar (rows 1718 to 1934, past column 3676) is the hardware's and cut off at the side's straight edge. Douglas-Peucker 0.006 in. Under the hinge's column the knurled nut's outline (to 1.476 under the axis) is dropped for the lower tab's bottom, 1.29: the nut is drawn as a piece of its own.","via":"harvest","note":"Out to the hinge's axis (z 1.081) between y -0.16 and -1.29: there the outline is the hinge's column seen from the side, knuckles and washers together; the script cuts each half clear of the other's knuckles. The foot under the window (to 1.52 under the axis) is the half's own."},"end_stock":{"plane":"zy","origin":"the tube's axis (the half's own bore's centre in the photo)","offset":{},"points":[[-0.5161,0.5392],[-0.641,0.4129],[-0.728,0.2726],[-0.7842,0.1126],[-0.8038,-0.0601],[-0.7842,-0.2299],[-0.5891,-0.9555],[-0.5568,-1.1394],[-0.5245,-1.2208],[-0.4754,-1.298],[-0.4291,-1.3317],[-0.342,-1.3598],[-0.2677,-1.4103],[-0.0136,-1.4327],[0.1913,-1.4103],[0.2236,-1.3906],[0.2881,-1.3148],[0.3611,-1.2868],[0.8804,-1.2896],[1.0812,-1.2896],[1.0812,-0.1611],[0.8945,-0.1569],[0.8369,-0.1288],[0.7934,-0.0867],[0.7752,-0.0587],[0.7541,0.0101],[0.7471,0.201],[0.6952,0.3203],[0.6404,0.4031],[0.5366,0.514],[0.3976,0.6122],[0.2573,0.6712],[0.1071,0.7021],[-0.0712,0.7063],[-0.2396,0.6796],[-0.3827,0.6249]],"scaleRefs":["law-tactical-gen-s-folder.bore_thread_crest_d"],"inputs":{"law-tactical-gen-s-folder.bore_thread_crest_d":1.1568},"tolerance":0.006,"photo":"references/law-tactical-gen-s-folder fcd2778b7b4e (Primary Arms 430116178_01: the black GEN-S folded open 180 degrees on white, both mating faces up, from straight above; 5000 x 5000)","method":"The stock half's mating face, seen from in front with the half turned 180 degrees about the hinge: its z in the part's frame, stock open, is the photo's column less its bore's centre (1599.7) over 712.5 px/in. Douglas-Peucker 0.006 in. The knurled nut's outline under the hinge's column dropped, as on the receiver half.","via":"harvest","note":"Its side away from the hinge leans in below the ring (0.80 out at the axis, 0.59 at 0.96 under it), where the receiver half's stands straight."}},"gaps":[{"what":"Where the hinge stands along the bore and where the halves meet, read only from how the part lies folded open: no square side view.","need":"A side view of the part square on (on a lower with its pins in frame, or alone beside a known length)."},{"what":"How far the hinge turns past 180 degrees, if at all, and what stops it: the photos have it at 180, lying flat.","need":"A photo from above of the adapter alone turned as far as it goes."},{"what":"The bolt carrier extension's scale: read so its length behind the shoulder is the 1.3 in it makes up (which its weight in steel bears out), the end that goes into the carrier comes out 0.053 in under the carrier's bore.","need":"A seller's or the maker's figure for the extension's length or diameter, or a photo of it beside a carrier."},{"what":"The receiver half's front face (its index protrusion, the hole over the takedown pin's spring) and the stock half's and receiver half's undersides (a hole in each): seen only in three-quarter.","need":"A photo of each face square on."},{"what":"Which product code a retail GEN-S carries: the maker's page gives 99312 (the Gen 3-M's before it) and 99329 for government and OEM sales; the sellers on file list 99329.","need":"The maker's dealer list or a box label."}]},"law-tactical-gen3m-folder":{"id":"law-tactical-gen3m-folder","name":"AR Folding Stock Adapter Gen 3-M","manufacturer":"Law Tactical","sku":"99312","url":"https://www.midwestgunworks.com/page/mgwi/prod/99312","category":"folding_adapter","description":"A hinge between the lower receiver and the buffer tube: press its button and the tube and stock swing to the rifle's left; unfolded they lock straight again. It moves the tube back 1.3 in, and a bolt carrier extension in the carrier's tail makes up the length. Sellers: \"Made from CNC Machined 4140 Steel with DLC finish\" (T.REX Arms); Law Tactical's sheet: \"Always close stock (unfold) before firing. The AR is not designed to be fired from the folded position.\"","weight":"law-tactical-gen3m-folder.weight","occupies":[],"integral":[],"brings":[],"seats":{"receiver_extension":{"parentInterface":"tube_socket","interface":"receiver_thread","folds":true,"note":"Law Tactical's sheet, step 4: \"Then install the Buffer Tube and stock onto the Hinge Assembly (1a) in the same manner it would be installed onto the rear of the rifle receiver.\" The end plate and castle nut go on as they would on a receiver, against the stock half's rear face; the buffer and its spring stay in the tube, held by the retaining pin when folded (step 5)."}},"requires":[],"folding":{"anchor":"hinge","moves":"stock_half","max":"law-tactical-gen3m-folder.fold_max","side":"left","inside":["carrier_extension"],"note":"Folds to the rifle's left: no page says it in words. Law Tactical's sheet draws the folded stock half on the near side of a lower shown from its left (steps 4 to 6), the patent's FIG. 6B draws the stock folded across the left side, and every photo of the part folded open has its halves the left way round (the ledger's hinge_z). Law Tactical's sheet: \"To avoid accidental firing in the folded position, the SAFETY should ALWAYS be ENGAGED BEFORE FOLDING stock and should REMAIN ENGAGED until stock is unfolded.\""},"anchors":{"receiver_thread":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the tube axis at the takedown pin's X, +x rearward (+z is then the rifle's left). The threaded flange screws into the lower here as a tube would."},"tube_socket":{"origin":["{.added_length}",0,0],"x":[1,0,0],"note":"Where a receiver extension's own frame stands with the adapter on: the takedown pin's X moved back by the adapter's length. The stock half's rear face is the lower's rear face moved back as far."},"hinge":{"origin":["{.hinge_x}",0,"{.hinge_z}"],"x":[1,0,0],"y":[0,1,0],"note":"On the hinge bolt's axis, upright, low on the rifle's left (the knuckles from just under the tube's axis down to the feet), in the plane where the two halves meet."}},"interfaces":{"receiver_thread":{"type":"ar15.buffer_tube_mount","role":"tube","anchor":"receiver_thread","params":{},"flips":false},"tube_socket":{"type":"ar15.buffer_tube_mount","role":"receiver","anchor":"tube_socket","params":{},"flips":false}},"materials":{"body":{"label":"Adapter","finish":"nitride","recolorable":false,"color":"steel-nitride-black","options":{"black":{"label":"Black","finish":"nitride","color":"steel-nitride-black","sku":"99312","source":"https://www.midwestgunworks.com/page/mgwi/prod/99312"},"fde":{"label":"FDE","finish":"cerakote","color":"law-tactical-fde","sku":"LTGEN3MFDE","source":"https://ads.midwestgunworks.com/page/mgwi/prod/ltgen3mfde"}},"default":"black","note":"The two halves and their knuckles. \"Made from CNC Machined 4140 Steel with DLC finish\" (T.REX Arms), \"Ionbond DLC finish\" (RECOIL): the catalog has no finish type for a diamond-like carbon coat, and the black is drawn as the nearest it has, a smooth black on steel (`nitride`, as SureFire's DLC parts are), not fitted to a photo. The FDE one's coat isn't named by any page on file (sellers say \"FDE\", Blackstone \"Flat Dark Earth\"): its photos show a flat, even tan with no highlight, drawn as `cerakote` and fitted to T.REX's and Midwest Gun Works' photos of it (data/colors/law-tactical.yaml). Piece by piece (T.REX's d540fee687f5 and 156bc8e73a87, Midwest Gun Works' 93ed44e08726, of the FDE one; Midwest Gun Works' af70d3e9c54e, Blackstone's 3e86c09fb510 and RECOIL's 55fec2c093b8 of the black; Law Tactical's own gallery photos are of the GEN-S, not this part): both halves and all three knuckles are the colour; the button, the latch, the hinge bolt's head and nut, the washers between the knuckles, the set screws, the threaded flange and the bolt carrier extension are black on both."},"hardware":{"label":"Button, flange and hardware","finish":"nitride","recolorable":false,"color":"steel-nitride-black","note":"Black on both colourways (the FDE one's photos, the same as the black one's): the button's bar out of the right side, the washers between the knuckles, the hinge bolt's knurled nut, the threaded flange and the bolt carrier extension. Steel; the finish of these isn't stated apart from the housing's DLC, and a black on steel isn't fitted to a photo."}},"components":{},"geometry":{"components":{"receiver_half":"law-tactical-gen3m-folder.receiver_half.glb","stock_half":"law-tactical-gen3m-folder.stock_half.glb","carrier_extension":"law-tactical-gen3m-folder.carrier_extension.glb"},"approximations":["Each half is its end outline run its length: the outlines are traced from T.REX's photo of the part folded open 180 degrees from straight above (both mating faces to the lens), scaled by the stock half's threaded bore; the faces are taken as flat and the sides as straight along the bore, as the photos from behind and above show them. The outline is the mating face's: whatever the halves have that differs toward their outer faces isn't seen.","The hinge's axis is half the housing's length behind the lower's rear face and the halves meet in its plane: read from how the part lies folded open on a table (each half flat on its outer face, the axis level between them) and from the two mating faces lying in one plane in that pose (the ledger's hinge_x and receiver_half_length). No square side view is on file; the patent's earlier embodiment draws its knuckles further back.","The hinge: an upright bolt low on the rifle's left, its two outer knuckles the stock half's and its middle one the receiver half's (US 8,769,855: \"a hinged joint comprised of a hinge pivot 138 and two hinge tabs 134 joined by a hinge pin 139\"), black washers between them and the knurled nut under them, each at the height and size T.REX's photo has it (the nut is drawn with the stock half, whose lower tab it bears on: it turns about its own axis). Each knuckle is a plain round about the axis, joined to its half by the half's own outline. The hinge bolt's socket head sits in a counterbore in the upper tab's top (both read on T.REX's photo from above, its hex socket the sheet's 1/8 in key; how far it is sunk, its height and the socket's depth are assumed), drawn with the stock half as the nut is; the bolt's shank inside the knuckles isn't drawn. Each half is cut clear of the other's knuckles.","The stock half's threaded bore is a 1 3/16-16 thread (lib.thread_x, a helix) between the extension's major diameter and its thread's crests as read; the receiver half's bore is the flange's lip, as read, through. The threaded flange is drawn in it: its thread the extension's, from the lower's rear face forward to where a tube's front face stands (std.receiver_extension.front_face_x), its bore the tube's (what the carrier runs in), its head in a counterbore at the receiver half's rear (assumed sizes: the ledger's flange_head_*); the flange's four tool cut-outs and its set screw aren't drawn.","On the stock half's front face its locking tab, low on the side away from the hinge, goes into a window in the receiver half's rear face where the button's retainer catches it: the tab's face size is read, how far it stands and the window's depth are assumed (the ledger). The button is a black bar out of the receiver half's right side at the height read, in the middle of the half's length (where along it isn't read); its slot through the half, its spring and its cover plate aren't drawn, nor the latch that holds the carrier in when folded (drawn as it is unfolded: inside its slot).","The stock half's rear face has its three holes (two small, one large below them), blind, as deep as assumed; their places and sizes are read on Blackstone's photo from behind and above, scaled across by the bore and up and down by the face's own height: good to about a twentieth of an inch.","The bolt carrier extension is turned from Midwest Gun Works' photo of it standing beside the FDE adapter (93ed44e08726; its black one, af70d3e9c54e, read the same way and kept beside it), scaled so that what stands behind its first shoulder is the 1.3 in it makes up (its lengths read foreshortened by the 17 degrees the lens looks down, its widths not): it lies in the carrier's tail with its first shoulder on the tail's rear end, where the carrier stands in battery (std.ar15.upper_rear_face_x), and reaches back to where the buffer then rests. Its O-rings and the end that goes into the carrier are inside the carrier and drawn plain; at this scale that end is 0.599 in, 0.026 under the carrier's .625 bore, which the O-rings' stand makes up. A darker band round its body's lower part (flush) isn't drawn.","Not drawn: the engraving (\"PAT. 8769855\", \"CLOSE BEFORE FIRING\", the logo), the set screws (the flange's, in the receiver half's right side, and the one under the stock half's thread), the faces' small chamfers beyond a 0.012 in break, the protrusion on the receiver half's front face that goes into the lower's index (it would stand in the lower's own metal, which the lowers on file don't have cut).","Its weight is the sellers' 8.5 oz for the housing and 2 oz for the extension. The model's steel (its two halves with the flange, washers, nut and bolt head: 3.15 cubic inches) weighs 14.4 oz, 1.69 times the housing's figure: the halves are drawn solid where the photos show faces, and whatever pockets the real part has inside (4140 machined from bar: the button's slot through the receiver half, its spring and cover, and more not seen) aren't drawn. The extension's (0.469 cubic inches, 2.14 oz) is the sellers' 2 oz, within its last digit."],"ledger":["law-tactical-gen3m-folder.added_length","law-tactical-gen3m-folder.hinge_x","law-tactical-gen3m-folder.hinge_z","law-tactical-gen3m-folder.length","law-tactical-gen3m-folder.width","law-tactical-gen3m-folder.height"]},"profiles":{"end_receiver":{"plane":"zy","origin":"the tube's axis (the half's own bore's centre in the photo)","offset":{},"points":[[0.1793,0.7277],[0.2974,0.7047],[0.424,0.6587],[0.5565,0.5781],[0.663,0.4802],[0.7493,0.3679],[0.8012,0.27],[0.8184,0.2211],[0.8271,0.1117],[0.8443,0.0541],[0.9249,-0.0495],[0.9451,-0.0639],[1.0343,-0.0582],[1.043,-0.0495],[1.0545,-0.0582],[1.1351,-0.0553],[1.1351,-1.2903],[1.0343,-1.2874],[0.9768,-1.2874],[0.9019,-1.2787],[0.8127,-1.2903],[0.4528,-1.2903],[0.3924,-1.3104],[0.3521,-1.3478],[0.329,-1.391],[0.3146,-1.4946],[0.2743,-1.5292],[-0.1402,-1.5321],[-0.2381,-1.5033],[-0.264,-1.4716],[-0.2956,-1.4025],[-0.3475,-1.3565],[-0.5317,-1.3536],[-0.6526,-1.319],[-0.6987,-1.2759],[-0.7361,-1.2125],[-0.7476,-1.1521],[-0.7476,-1.0628],[-0.79,-1.04],[-0.7908,0.0455],[-0.762,0.1837],[-0.6958,0.3334],[-0.5864,0.4802],[-0.4914,0.5608],[-0.3964,0.6212],[-0.3763,0.6155],[-0.3417,0.6414],[-0.2525,0.6817],[-0.1143,0.722],[-0.0049,0.7335]],"scaleRefs":["law-tactical-gen3m-folder.bore_thread_crest_d"],"inputs":{"law-tactical-gen3m-folder.bore_thread_crest_d":1.1515},"tolerance":0.006,"photo":"references/law-tactical-gen3m-folder d540fee687f5 (T.REX Arms' gallery: the FDE adapter folded open 180 degrees on a slate table, both mating faces up, from straight above; 3000 x 3000)","method":"The receiver half's mating face, seen from behind (its z is minus the photo's column less the bore's centre, 1882.3, over 347.4 px/in). Its side away from the hinge is drawn straight at 0.79 from y 0.05 down to -1.04, where the mask had the button's window, a set screw and the bar's shadow; the bar itself (columns past 2163, rows 1640 to 1790) is the hardware's. Douglas-Peucker 0.006 in. One point under the hinge's column (0.997, -1.316), the knurled nut's top in the mask, dropped.","via":"harvest","note":"Out to the hinge's axis (z 1.135) between y -0.06 and -1.29: there the outline is the hinge's column seen from the side, knuckles and lugs together; the script cuts each half clear of the other's knuckles."},"end_stock":{"plane":"zy","origin":"the tube's axis (the half's own bore's centre in the photo)","offset":{},"points":[[-0.5331,0.5176],[-0.6483,0.3852],[-0.7001,0.2988],[-0.7404,0.2067],[-0.7778,0.0628],[-0.7865,-0.1128],[-0.7519,-0.3086],[-0.5619,-0.9765],[-0.536,-1.1406],[-0.4957,-1.2413],[-0.4381,-1.3248],[-0.4036,-1.3478],[-0.3431,-1.3651],[-0.3086,-1.3853],[-0.2654,-1.4342],[-0.2424,-1.5004],[-0.2078,-1.5263],[0.2009,-1.5321],[0.3017,-1.5148],[0.319,-1.5033],[0.3391,-1.4745],[0.3564,-1.3363],[0.4024,-1.2931],[0.912,-1.2903],[0.9667,-1.2931],[1.1365,-1.2903],[1.1365,-0.0553],[1.1164,-0.0438],[1.1077,-0.0524],[0.984,-0.0438],[0.9724,-0.0553],[0.9206,-0.0553],[0.8659,-0.0438],[0.8199,-0.0092],[0.817,0.0714],[0.794,0.1837],[0.7594,0.2758],[0.7047,0.3823],[0.6068,0.4917],[0.5176,0.5637],[0.4284,0.6126],[0.2844,0.6731],[0.1635,0.7018],[0.0599,0.7134],[-0.0725,0.7134],[-0.1762,0.699],[-0.2712,0.6731],[-0.3892,0.6212]],"scaleRefs":["law-tactical-gen3m-folder.bore_thread_crest_d"],"inputs":{"law-tactical-gen3m-folder.bore_thread_crest_d":1.1515},"tolerance":0.006,"photo":"references/law-tactical-gen3m-folder d540fee687f5 (T.REX Arms' gallery: the FDE adapter folded open 180 degrees on a slate table, both mating faces up, from straight above; 3000 x 3000)","method":"The stock half's mating face, seen from in front with the half turned 180 degrees about the hinge: its z in the part's frame, stock open, is the photo's column less its bore's centre (1092.2) over 347.4 px/in. Douglas-Peucker 0.006 in. One point under the hinge's column (0.941, -1.316), the knurled nut's top in the mask, dropped.","via":"harvest","note":"Its side away from the hinge leans in below the ring, where the receiver half's stands straight (both photos of that pose show it so)."}},"gaps":[{"what":"Where the hinge stands along the bore and where the halves meet, read only from how the part lies folded open: no square side view.","need":"A side view of the part square on (on a lower with its pins in frame, or alone beside a known length)."},{"what":"How far the hinge turns past 180 degrees, if at all, and what stops it: the photos have it at 180, lying flat; the patent says the stock folds flat against the receiver.","need":"A photo from above of the adapter alone turned as far as it goes."},{"what":"The receiver half's front face: its protrusion into the lower's index indentation (the sheet's X), the hole over the takedown pin's spring, and any relief round the flange. No photo of that face square on is on file.","need":"A photo of the receiver half's front face, square on (Law Tactical's or a seller's)."},{"what":"The bolt carrier extension's scale: read so its length behind the shoulder is the 1.3 in it makes up, on two close photos taken from above; the stem's length differs between them by 0.054 in (a conflict in the ledger).","need":"A seller's or the maker's figure for the extension's length or diameter, or a side photo of it square on."},{"what":"Law Tactical's own page for the Gen 3-M now shows the Gen-S; Primary Arms' page for it (URL from the brief) answered 404, Rainier Arms' and AT3's refused the reader (403).","need":"Nothing: the sellers' pages on file give the figures."}]},"magpul-ctr":{"id":"magpul-ctr","name":"CTR carbine stock, mil-spec","manufacturer":"Magpul","sku":"MAG310","category":"stock","description":"Magpul's A-frame carbine stock with a friction lock under the tube that takes up its play on the receiver extension, a push-button QD sling socket, and a 0.3 in rubber butt pad. The MOE Carbine is this stock without the lock and the socket; Magpul lists both at the same size and length of pull.","weight":"magpul-ctr.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"butt":{"origin":[0,0,0],"note":"The butt's plane on the tube axis: the part frame's origin. Overall length and length of pull end here."},"tube":{"origin":["{.butt_behind_pin_pos1}",0,0],"x":[-1,0,0],"note":"Stock frame: origin on the tube axis in the plane of the butt, +x forward. At position 1 this anchor sits at the takedown pin's X."}},"interfaces":{"tube":{"type":"receiver_extension","role":"stock","anchor":"tube","params":{"profile":"mil-spec"},"flips":false,"note":"MAG310 is the Mil-Spec model. The Commercial-Spec CTR (MAG311) is gone from Magpul's site; retailers list it longer (7.2 in) and heavier (9.3 oz): another part, not this body bored differently."}},"materials":{"body":{"label":"Stock body","finish":"polymer","recolorable":true,"color":"magpul-black","sheen":"satin","options":{"black":{"label":"Black","finish":"polymer","color":"magpul-black","sheen":"satin","sku":"MAG310-BLK","source":"https://magpul.com/ctr-carbine-stock-mil-spec.html"},"fde":{"label":"FDE","finish":"polymer","color":"magpul-fde","sheen":"satin","sku":"MAG310-FDE","source":"https://magpul.com/ctr-carbine-stock-mil-spec.html"},"mcb":{"label":"Modified Coyote Brown","finish":"polymer","color":"magpul-mcb","sheen":"satin","sku":"MAG310-MCB","source":"https://magpul.com/ctr-carbine-stock-mil-spec.html"},"odg":{"label":"ODG","finish":"polymer","color":"magpul-odg","sheen":"satin","sku":"MAG310-ODG","source":"https://magpul.com/ctr-carbine-stock-mil-spec.html"},"sgy":{"label":"Stealth Gray","finish":"polymer","color":"magpul-stealth-gray","sheen":"satin","sku":"MAG310-GRY","source":"https://magpul.com/ctr-carbine-stock-mil-spec.html"}},"default":"black","note":"The five colours Magpul's page offers MAG310 in (its swatches: Black, Flat Dark Earth, Modified Coyote Brown, Olive Drab Green, Stealth Gray, each with its number; a sixth swatch, Foliage Green, has no product behind it). Four are the presets matched on the MOE SL; Modified Coyote Brown was matched on this stock's own gallery photos (data/colors/magpul.yaml). In every colour the release latch and the friction lock's lever are the body's colour, as drawn (Magpul's gallery shots 01.1 and 02.1 of each). What stays black on every colour and isn't drawn: the QD socket's steel cup, the lock pin's head, the friction lock's pivot pin."},"buttpad":{"label":"Buttpad","finish":"rubber","recolorable":false,"color":"magpul-black","note":"Black rubber on every colour of stock (Magpul's FDE, MCB, ODG and Stealth Gray gallery shots 01.1 and 02.1)."}},"components":{"body":{"label":"Stock body","material":"body"},"buttpad":{"label":"Buttpad","material":"buttpad"}},"geometry":{"model":"magpul-ctr.glb","components":{},"approximations":["Visual hull of the traced side photo (Primary Arms, scaled by Magpul's 7.0 x 5.2 in, which fit it within 1.0%) and an end section that isn't the CTR's own: the MOE Carbine's, from Magpul's design patent (US D600,308 S, FIG. 4), scaled by the CTR's 5.2 x 1.7 in. The CTR has no design patent and no end view of it was found.","The frame below the tube is cut to the MOE Carbine's 0.69 in; the friction lock's housing under the tube's front is left at the section's width (its own isn't sourced), and the butt's flare into the frame is a step 0.35 in ahead of the pad's seam.","The seven openings the side photo shows are cut through (two cheek slots, the QD socket, the window, the sling slot, the brace's slot, the lanyard hole); the rubber butt pad is its own part behind its seam. The release latch is its side silhouette, left standing in the frame's window at the frame's width. Not drawn: the friction lock's lever, the QD socket's steel cup, the footman's loop, the recessed panels, the markings. Edges broken at 0.03 in.","Bored from its front for the receiver extension, a keyhole: the bore at 1.158 in, which isn't the CTR's own but the hidden circle on the MOE Carbine's patent front view (± 0.04, which takes in the mil-spec tube's 1.148: no clearance is claimed), one diameter all the way; under it the indexing rail's channel at the rail's own width and depth (0.49 in, to 0.874 in below the axis), with nothing to spare: no clearance is known. It ends where the tube's rear end reaches with the stock collapsed (the buffer kit's tube); the real bore's end and its mouth's flare aren't sourced. The two cheek slots, cut right across, open into it.","Its seat on the tube is the MOE Carbine's, moved by where each stock's lock pin stands: the two share their latch. Its own photo on a rifle, three steps out, would put it 0.25 in further forward, its front inside the castle nut."],"ledger":["magpul-ctr.length","magpul-ctr.height","magpul-ctr.width","magpul-ctr.tube_axis_below_top","magpul-ctr.frame_width","magpul-ctr.butt_behind_pin_pos1","magpul-ctr.bore_diameter","magpul-ctr.rail_channel_width","magpul-ctr.rail_channel_floor_below_axis"]},"profiles":{"side":{"plane":"xy","origin":"rearmost point of the butt pad (x) and the top edge at its highest (y); the photo shows the top level, so the tube axis is horizontal","offset":{"y":"tube_axis_below_top"},"points":[[0,-0.342],[0,-0.787],[0.03,-0.954],[0.041,-1.142],[0.273,-2.448],[0.354,-3.055],[0.456,-3.977],[0.506,-4.726],[0.542,-5.01],[0.577,-5.086],[0.666,-5.169],[0.742,-5.189],[0.853,-5.184],[0.878,-5.215],[0.914,-5.225],[1.375,-5.215],[1.496,-5.179],[1.6,-5.086],[1.666,-4.919],[1.701,-4.878],[1.701,-4.858],[1.775,-4.784],[4.022,-3.215],[4.402,-2.967],[4.488,-2.987],[4.559,-2.942],[4.607,-2.898],[4.622,-2.853],[4.746,-2.744],[4.797,-2.729],[4.827,-2.688],[4.898,-2.658],[4.929,-2.618],[4.995,-2.592],[5.05,-2.536],[5.106,-2.516],[5.131,-2.481],[5.217,-2.44],[5.238,-2.405],[5.298,-2.385],[5.344,-2.334],[5.394,-2.319],[5.44,-2.268],[5.506,-2.243],[5.683,-2.121],[5.794,-2.081],[5.926,-2.071],[6.68,-2.081],[6.696,-2.071],[6.746,-2.106],[6.812,-2.106],[6.842,-2.091],[6.88,-2.023],[6.916,-1.734],[6.961,-0.985],[6.967,-0.57],[6.916,-0.119],[6.817,-0.056],[0.605,-0.051],[0.544,0],[0.397,0],[0.332,-0.056],[0.311,-0.046],[0.154,-0.066],[0.073,-0.086],[0.015,-0.134]],"features":{"through":[[[1.281,-1.111],[1.296,-1.071],[1.359,-1.028],[2.362,-1.028],[2.385,-1.051],[2.38,-1.091],[2.342,-1.139],[2.301,-1.154],[1.329,-1.154]],[[4.82,-1.091],[4.873,-1.023],[4.908,-1.013],[5.764,-1.018],[5.777,-1.03],[5.767,-1.096],[5.708,-1.144],[4.908,-1.144],[4.833,-1.139]],[[1.261,-2.018],[1.266,-1.957],[1.291,-1.901],[1.364,-1.833],[1.425,-1.813],[1.547,-1.833],[1.63,-1.926],[1.63,-1.987],[1.6,-2.063],[1.521,-2.131],[1.471,-2.147],[1.415,-2.147],[1.344,-2.121],[1.296,-2.078]],[[1.296,-2.605],[1.306,-2.488],[1.347,-2.418],[1.415,-2.349],[1.567,-2.319],[1.663,-2.263],[1.742,-2.169],[1.777,-2.053],[1.81,-2.015],[2.078,-1.792],[2.225,-1.732],[2.752,-1.726],[2.764,-1.739],[2.311,-1.929],[2.248,-1.977],[2.233,-2.012],[2.233,-2.068],[2.258,-2.149],[2.248,-2.159],[2.273,-2.205],[2.268,-2.245],[2.288,-2.286],[2.321,-2.309],[3.688,-1.919],[4.063,-1.894],[4.086,-1.871],[4.091,-1.825],[4.103,-1.813],[4.121,-1.825],[4.162,-1.906],[4.167,-2.038],[4.131,-2.134],[4.058,-2.223],[1.871,-3.959],[1.8,-4.01],[1.719,-4.04],[1.613,-4.035],[1.521,-3.99],[1.448,-3.901],[1.438,-3.845],[1.362,-3.081],[1.342,-3.02]],[[0.871,-2.357],[0.886,-2.291],[0.964,-2.243],[1.03,-2.263],[1.063,-2.301],[1.099,-2.499],[1.2,-3.369],[1.195,-3.455],[1.132,-3.504],[1.066,-3.498],[1.023,-3.45]],[[2.167,-4.012],[2.177,-3.972],[2.215,-3.934],[3.096,-3.276],[3.172,-3.26],[3.205,-3.283],[3.22,-3.329],[3.187,-3.362],[2.24,-4.076],[2.2,-4.065]],[[1.073,-4.812],[1.132,-4.749],[1.329,-4.744],[1.387,-4.782],[1.382,-4.812],[1.339,-4.85],[1.182,-4.86],[1.116,-4.85]]],"buttpad":[[[-2.104,1.451],[0.327,1.451],[0.327,0.033],[0.332,-0.321],[0.337,-0.575],[0.332,-0.828],[0.352,-1.081],[0.382,-1.334],[0.428,-1.587],[0.473,-1.84],[0.519,-2.093],[0.559,-2.347],[0.6,-2.6],[0.63,-2.853],[0.666,-3.106],[0.691,-3.359],[0.721,-3.612],[0.747,-3.866],[0.772,-4.119],[0.792,-4.372],[0.818,-4.625],[0.843,-4.878],[0.868,-5.131],[0.883,-5.283],[0.904,-6.078],[-2.104,-6.078]]],"frame":[[[0.777,-1.562],[4.478,-1.562],[4.478,-6.078],[1.253,-6.078],[1.233,-5.283],[1.218,-5.131],[1.192,-4.878],[1.167,-4.625],[1.142,-4.372],[1.121,-4.119],[1.096,-3.866],[1.071,-3.612],[1.04,-3.359],[1.015,-3.106],[0.98,-2.853],[0.949,-2.6],[0.909,-2.347],[0.868,-2.093],[0.823,-1.84],[0.777,-1.587]]]},"scaleRefs":["magpul-ctr.length","magpul-ctr.height"],"inputs":{"magpul-ctr.height":5.2,"magpul-ctr.length":7},"tolerance":0.01,"photo":"references/magpul-ctr c0e805964cd6 (Primary Arms MAG310-BLK_00.jpg, straight right side on white, 2200 x 1467)","method":"luminance < 235, closing ×2, largest piece, holes filled; scale from magpul-ctr.length = 7 in (x-extent 1376 px → 196.6 px/in) and magpul-ctr.height = 5.2 in (y-extent 1032 px → 198.5 px/in), which agree within 1.0%; mean 197.5 px/in; origin at x min, y max of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 66 points (IoU 0.998 with the full outline); features through the same placement (through: reviewed pixel boxes; buttpad: reviewed pixel boxes; frame: reviewed pixel boxes) (tools/trace.py)","via":"harvest","note":"The seven openings are cut through. The latch, the friction lock's lever, the footman's loop, the recessed panels and the markings aren't in the outline."},"front":{"plane":"zy","origin":"the top edge, centred: as the side profile, offset down to the tube axis","offset":{"y":"tube_axis_below_top"},"points":[[-0.848,-1.009],[-0.699,-1.911],[-0.609,-2.994],[-0.59,-3.69],[-0.622,-4.702],[-0.603,-4.85],[-0.519,-5.024],[-0.4,-5.131],[-0.329,-5.169],[-0.142,-5.215],[0.161,-5.215],[0.348,-5.163],[0.451,-5.092],[0.577,-4.947],[0.616,-4.792],[0.609,-4.148],[0.596,-4.122],[0.603,-3.606],[0.59,-3.561],[0.603,-3.548],[0.596,-3.394],[0.609,-3.368],[0.603,-3.2],[0.616,-3.181],[0.622,-2.826],[0.641,-2.73],[0.648,-2.459],[0.661,-2.446],[0.654,-2.395],[0.674,-2.311],[0.706,-1.879],[0.738,-1.782],[0.77,-1.466],[0.802,-1.312],[0.796,-1.273],[0.835,-1.112],[0.848,-0.97],[0.815,-0.822],[0.68,-0.448],[0.564,-0.255],[0.425,-0.129],[0.322,-0.071],[0.18,-0.019],[0,-0.006],[-0.013,0],[-0.116,-0.006],[-0.335,-0.077],[-0.413,-0.122],[-0.545,-0.235],[-0.622,-0.338],[-0.667,-0.429],[-0.712,-0.57],[-0.777,-0.706]],"scaleRefs":["magpul-ctr.height","magpul-ctr.width"],"inputs":{"magpul-ctr.height":5.2,"magpul-ctr.width":1.7},"tolerance":0.01,"photo":"references/magpul-moe-carbine a74bc8906efc (US D600,308 S (Magpul), FIG. 4 front elevation, 300 dpi: the MOE Carbine's patent, standing in for the CTR)","method":"luminance < 128, inside [440, 2740, 1290, 3050], closing ×3, largest piece, holes filled, inset 2 px (half the outline's stroke); rotated -90.0° as declared; scale from magpul-ctr.height = 5.2 in (y-extent 809 px → 155.6 px/in) and magpul-ctr.width = 1.7 in (x-extent 263 px → 154.7 px/in), which agree within 0.6%; mean 155.1 px/in; origin at x center, y max of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 53 points (IoU 0.995 with the full outline) (tools/trace.py)","via":"harvest","note":"Not the CTR's own section: the MOE Carbine's design patent, standing in. The CTR has no design patent and no end view of it was found; Magpul lists both stocks at 5.2 x 1.7 in. The CTR's friction lock housing and QD socket aren't in it."}},"gaps":[{"what":"Its end section and the friction lock housing's width (the MOE Carbine's section stands in)","need":"a straight end-on or underside photo of the CTR with a known size in frame"},{"what":"Its seat on the tube from its own photo (three steps out, it lands inside the castle nut)","need":"a straight side photo of it collapsed on a lower with both receiver pins in view"},{"what":"The pieces that stay black on a coloured stock (the QD socket's steel cup, the lock pin's head, the friction lock's pivot pin) as surfaces of their own","need":"their sizes read into the ledger (the cup's rim round the traced socket, the pins' heads) from a straight side photo of a coloured CTR"}]},"magpul-mbus-3-front":{"id":"magpul-mbus-3-front","name":"MBUS 3 Sight – Front","manufacturer":"Magpul","sku":"MAG1166","url":"https://magpul.com/mbus-3-sight-front.html","category":"backup_sight","description":"Magpul's MBUS 3 Sight – Front: a polymer folding backup front sight for a Picatinny rail, deployed by a spring-loaded latch, with a tool-less elevation wheel and a post that turns between a 0.06 in standard and a 0.04 in match width. Black, Flat Dark Earth, Olive Drab Green.","weight":"magpul-mbus-3-front.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":["{.bolt_x}",0,0],"note":"On the rail's top at the cross bolt's axis, which lies in the rail slot the sight is put at: 0.06 in ahead of the middle of the clamp, where the part frame's origin is (+x toward the muzzle, +y up)."},"optical_axis":{"origin":["{.clamp_length} / 2 - {.hinge_behind_front}","{.sight_line_above_rail}",0],"note":"The sight line it has standing: the post's tip, which stands over the hinge's axis (the wheel and the post are on the arm's middle plane), 0.52 in behind the middle of the clamp."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":"={.clamp_length} / 2 + {.bolt_x}","clamp_front":"={.clamp_length} / 2 - {.bolt_x}"},"flips":false,"start":"front","note":"A front sight goes on the forend's rail, the arm to the rear. Magpul's page (https://magpul.com/mbus-3-sight-front.html, Technical Specifications): \"*NOTE: Cannot be mounted to a railed gas block due to excess heat issues. Front MBUS must be mounted to a railed forend on the same plane as the receiver rail. Because of this the sight is also not compatible with Magpul Hand Guards.\" Its installation sheet (092-0064-A): \"WARNING: DO NOT INSTALL ON M1913 GAS BLOCKS\"; \"Remove the 10-24 Dual Drive Screw from the MBUS 3 and slide it onto the rail with Sight Arm to the rear.\" The clamp is the base (0.69 in); standing, the arm's foot reaches 0.38 in behind it over the rail, and folded the arm lies 1.44 in behind it: neither is clamped."},"sight_line":{"type":"optic.sight_line","role":"irons","params":{"magnification":"1x"},"flips":false,"note":"An iron sight: it doesn't magnify, and nothing is checked against it (data/interfaces.yaml). Magpul: \"Standard AR sight height for across-the-board compatibility\"."}},"folds":{"up":"up","folded":"folded","note":"Folded, the arm lies back from its hinge along the rail behind the base, its rear face down (Magpul's photo of it on a rail; the patent's FIG. 8)."},"materials":{"body":{"label":"Sight","finish":"polymer","recolorable":false,"color":"magpul-black","sheen":"matte","options":{"black":{"label":"Black","finish":"polymer","color":"magpul-black","sheen":"matte","sku":"MAG1166-BLK","source":"https://www.milehighshooting.com/magpul-mbus-3-sight-front/"},"fde":{"label":"Flat Dark Earth","finish":"polymer","color":"magpul-fde","sheen":"matte","sku":"MAG1166-FDE","source":"https://www.midwestgunworks.com/page/mgwi/prod/mag1166-fde"},"odg":{"label":"Olive Drab Green","finish":"polymer","color":"magpul-odg","sheen":"matte","sku":"MAG1166-ODG","source":"https://www.primaryarms.com/magpul-mbus-3-front-sight-olive-drab-green"}},"default":"black","note":"Magpul's impact-resistant polymer, in Magpul's colours as matched on the MOE SL: the base, the arm, the latch and the elevation wheel. The wheel is the body's colour: Magpul's own photograph of the FDE sight in the hand (gallery 05) and T.REX ARMS' photographs of the FDE and the green sight have it so; Magpul's FDE catalog image (01.1), where it is black, is the black sight's render recoloured, and isn't followed (settled 2026-10-06). The colour numbers are as sellers print them; Magpul's page prints MAG1166 and, in its data, MAG1166_RET_BLK_, _FDE_ and _ODG_. Three colours today (read 2026-10-06 on the harvested copy of Magpul's page). Its swatches list a Stealth Gray with no product behind it, and Scheels' older copy says the sights \"will be available in Black, Flat Dark Earth, Stealth Gray, and OD Green\": no page on file sells a gray one."},"hardware":{"label":"Bolt, pins, spring and post","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The cross bolt and its head, the hinge pin, the pin through the cheeks, the hinge's coil spring and the sight post: black on every colour of the sight in Magpul's and T.REX ARMS' photographs (on the FDE sight: the post, the screw's slotted head in its round FDE rim, the two pins, the spring under the latch). What they are made of and coated with isn't stated; a black on steel isn't fitted to a photo, and the colour is the placeholder black."}},"components":{},"geometry":{"components":{"up":"magpul-mbus-3-front.up.glb","folded":"magpul-mbus-3-front.folded.glb"},"approximations":["Built from Magpul's design patent (US D1,010,056 S: its side, rear, front, top and bottom views of the sight standing), scaled so that the arm folded back about its hinge makes the published length, 2.13 in. At that scale the body is 1.14 in between its cheeks (the sellers' older \"1.15 in at its widest point\") and its top 0.43 in over the rail folded (their \"0.44\"). Magpul's present page says 1.38 in wide and about 0.47 in high: the model is 1.28 in across the boss and the bolt's head, as the patent and Magpul's own photographs have it (1.26 to 1.30), and nothing on file is 1.38.","Folded is the standing arm turned a quarter turn back about the hinge's axis, its flat rear face 0.01 in over the rail: the patent draws it folded only in perspective (FIG. 8), and Magpul's photo of it on a rail agrees with the length and the height this gives.","The post's tip is drawn at the published sight line (T.REX ARMS' \"Centerline Height 1.41 inches\"), 0.02 in above where the patent draws it: the post screws up and down. Its blade is the page's two widths (0.06 in across, 0.04 in thick), flared to its root; the root is a plain block.","The base's inside isn't drawn in any view: its two hinge lugs are plain rounds on webs, where the patent's broken lines and Magpul's underside photo put them; the latch is a plate on the base's top standing as far over the cheeks as the front view's broken lines show (0.02 in), with no hinge or catch of its own; the rail's channel is the patent's broken-line rail, made the standard's head in section (MIL-STD-1913's, since 2026-10-12) from the rail's top down to the lower gauge line where the base has its cheeks: the patent's is a few hundredths wider and square over a rail's upper faces.","The elevation wheel is twelve shallow flutes at the diameter their spacing gives (0.41 in); the two oblong pockets in the arm's rear face are cut a tenth of the arm's thickness deep, and the long recess in each of its sides a twentieth (0.04 and 0.02 in: no view gives their depths). The lettering (\"MBUS\", \"UP\", Magpul's mark) and the bolt head's hex socket aren't drawn. Edges broken at 0.012 in.","The bolt's head stands 0.05 in off the right cheek in a moulded rim as wide as the boss on the left, as Magpul's photographs show it; the patent draws the head in broken lines, 0.08 in out."],"ledger":["magpul-mbus-3-front.length","magpul-mbus-3-front.height_up","magpul-mbus-3-front.length_up","magpul-mbus-3-front.clamp_length","magpul-mbus-3-front.clamp_below_rail","magpul-mbus-3-front.hinge_behind_front","magpul-mbus-3-front.hinge_y","magpul-mbus-3-front.knuckle_d","magpul-mbus-3-front.body_width","magpul-mbus-3-front.bolt_x","magpul-mbus-3-front.bolt_below_rail","magpul-mbus-3-front.boss_d","magpul-mbus-3-front.boss_out","magpul-mbus-3-front.screw_head_d","magpul-mbus-3-front.screw_head_out","magpul-mbus-3-front.wheel_d","magpul-mbus-3-front.wheel_flutes","magpul-mbus-3-front.post_width_standard","magpul-mbus-3-front.post_width_match","magpul-mbus-3-front.sight_line_above_rail"]},"profiles":{"side":{"plane":"xy","origin":"the rail's top at the middle of the clamp (the base's two ends); the hinge block's underside is the rail's top","offset":{},"points":[[-0.727,1.41],[-0.727,0.216],[-0.717,0.156],[-0.686,0.096],[-0.64,0.05],[-0.562,0],[-0.354,0],[-0.346,-0.009],[-0.296,-0.188],[-0.265,-0.225],[-0.244,-0.237],[-0.184,-0.249],[0.235,-0.249],[0.274,-0.244],[0.304,-0.23],[0.337,-0.188],[0.347,-0.154],[0.347,-0.022],[0.335,0.069],[0.277,0.29],[0.253,0.335],[0.205,0.373],[0.108,0.397],[-0.074,0.426],[-0.135,0.432],[-0.24,0.431],[-0.245,0.426],[-0.251,0.43],[-0.287,0.386],[-0.291,0.315],[-0.298,0.309],[-0.305,0.316],[-0.31,0.976],[-0.315,0.997],[-0.331,1.015],[-0.337,1.076],[-0.306,1.106],[-0.304,1.141],[-0.312,1.153],[-0.339,1.153],[-0.345,1.159],[-0.364,1.367],[-0.382,1.4],[-0.415,1.426],[-0.618,1.483],[-0.664,1.489],[-0.688,1.483],[-0.709,1.463]],"features":{"pivot_pin":[[[-0.589,0.294],[-0.442,0.294],[-0.442,0.147],[-0.589,0.147]]],"latch_pin":[[[-0.213,0.331],[-0.113,0.331],[-0.113,0.231],[-0.213,0.231]]],"knuckle_face":[[[-0.692,0.396],[-0.34,0.396],[-0.34,0.044],[-0.692,0.044]]],"side_recess":[[[-0.454,1.283],[-0.458,1.305],[-0.474,1.321],[-0.576,1.345],[-0.596,1.339],[-0.608,1.321],[-0.61,1.299],[-0.61,0.368],[-0.453,0.368]]],"front_recess":[[[-0.28,1.174],[-0.347,1.174],[-0.309,0.782],[-0.28,0.782]]]},"scaleRefs":["magpul-mbus-3-front.clamp_length","magpul-mbus-3-front.length_up","magpul-mbus-3-front.height_up"],"inputs":{"magpul-mbus-3-front.clamp_length":0.692,"magpul-mbus-3-front.height_up":1.488,"magpul-mbus-3-front.length_up":1.072},"tolerance":0.004,"photo":"references/magpul-mbus-3-front 2017081c8b13 (US D1,010,056 S (Magpul, 'Gun sight'), FIG. 3 right elevation, 300 dpi)","method":"luminance < 128, inside [700, 730, 1810, 2420], closing ×3, largest piece, holes filled, inset 2 px (half the outline's stroke); frame from the reviewed holes front_rail, rear_rail, rear_top, front_top (918.7 px/in, rms 0.000 in over 4 points); origin at the photo's frame; Douglas-Peucker at 0.004 in with the extremes kept: 48 points (IoU 0.996 with the full outline); checks: width 1.073 ± 0.003; height 1.738 ± 0.004; features through the same placement (pivot_pin: the hinge's pin, in broken lines, concentric with the arm's round end (a circle fitted to it: centre 958.2, 1936.3, r 67.6 px); latch_pin: a smaller pin through the cheek above the cross bolt, in broken lines (centre 1282.5, 1880.4, r 46 px); knuckle_face: the flat face of the arm's round end, a circle about the hinge inside its rim (fitted: centre 958.2, 1936.3, r 161.7 px); side_recess: the long recess in the arm's side above its round end (the heavy inner outline: its walls at u 872 and 1016, its top sloping with the wings' from v 903 to 925); it runs down into the round end's face; front_recess: ahead of the wings' sloping front face carried on down (it runs from u 1095.5 at the top through 1142 at v 1360 and meets the pad's face at v 1420: FIG. 2 draws it inside the outline, mirrored): the arm's face beside the wheel's pad lies on that slope, and only the pad and its neck stand forward of it) (tools/trace.py)","via":"harvest","note":"The whole sight standing, seen from the right. The cross bolt's head (broken lines) is inside the cheek's outline. The post is hidden between the wings."},"rear":{"plane":"zy","origin":"the rail's top, on the sight's middle plane","offset":{},"points":[[-0.649,-0.191],[-0.642,-0.202],[-0.625,-0.207],[-0.515,-0.224],[-0.473,-0.247],[-0.344,-0.248],[-0.345,-0.189],[-0.351,-0.183],[-0.354,-0.205],[-0.472,-0.202],[-0.469,-0.156],[-0.382,-0.155],[-0.391,-0.142],[-0.4,-0.139],[-0.398,-0.104],[0.399,-0.104],[0.402,-0.139],[0.381,-0.154],[0.47,-0.155],[0.472,-0.198],[0.363,-0.2],[0.36,-0.181],[0.353,-0.181],[0.345,-0.189],[0.344,-0.248],[0.47,-0.248],[0.495,-0.234],[0.555,-0.229],[0.57,-0.222],[0.574,0.171],[0.57,0.333],[0.527,0.378],[0.527,0.44],[0.518,0.491],[0.444,0.674],[0.429,0.729],[0.402,1.34],[0.347,1.483],[0.341,1.488],[0.284,1.488],[0.269,1.476],[0.247,1.204],[0.237,1.182],[0.213,1.16],[0.185,1.152],[-0.012,1.156],[-0.016,1.152],[-0.186,1.152],[-0.223,1.166],[-0.238,1.183],[-0.248,1.208],[-0.27,1.479],[-0.281,1.488],[-0.341,1.488],[-0.348,1.483],[-0.401,1.336],[-0.425,0.762],[-0.432,0.715],[-0.513,0.506],[-0.527,0.443],[-0.527,0.377],[-0.571,0.33],[-0.571,0.205],[-0.637,0.191],[-0.648,0.182]],"features":{"legs":[[[-0.527,0.379],[0.527,0.379],[0.527,0.01],[-0.527,0.01]]],"fork":[[[-0.345,0.338],[0.349,0.338],[0.349,-0.035],[-0.345,-0.035]]],"lugs":[[[-0.324,0.338],[-0.175,0.338],[-0.175,0.077],[-0.324,0.077]],[[0.175,0.338],[0.324,0.338],[0.324,0.077],[0.175,0.077]]],"spring":[[[-0.166,0.338],[0.166,0.338],[0.166,0.077],[-0.166,0.077]]],"window":[[[-0.173,1.044],[0.174,1.044],[0.174,0.706],[-0.173,0.706]]],"wheel":[[[-0.203,1.015],[0.204,1.015],[0.204,0.725],[-0.203,0.725]]],"pockets":[[[-0.371,0.623],[-0.109,0.623],[-0.109,0.501],[-0.371,0.501]],[[0.108,0.623],[0.365,0.623],[0.365,0.501],[0.108,0.501]]],"post_base":[[[-0.062,1.235],[0.061,1.235],[0.061,1.152],[-0.062,1.152]]],"post_stem":[[[-0.018,1.387],[0.019,1.387],[0.019,1.235],[-0.018,1.235]]]},"scaleRefs":["magpul-mbus-3-front.body_width","magpul-mbus-3-front.height_up"],"inputs":{"magpul-mbus-3-front.body_width":1.143,"magpul-mbus-3-front.height_up":1.488},"tolerance":0.004,"photo":"references/magpul-mbus-3-front 21c2b9876c1b (US D1,010,056 S (Magpul, 'Gun sight'), FIG. 4 rear elevation, 300 dpi)","method":"luminance < 128, inside [620, 730, 1900, 2420], 2 boxes excluded, closing 5 px ×6, holes filled, inset 2 px (half the outline's stroke); frame from the reviewed holes left_rail, right_rail, left_top, right_top (919.0 px/in, rms 0.000 in over 4 points); origin at the photo's frame; Douglas-Peucker at 0.004 in with the extremes kept: 65 points (IoU 0.995 with the full outline); checks: height 1.737 ± 0.004; features through the same placement (legs: the arm's two legs: their outer faces (u 773.5 and 1741.5) from where the cheeks' chamfers meet them down to their round ends' undersides (v 2129.5); fork: the opening between the legs, where the base's hinge lugs and the spring are: its sides are where the legs' underside strokes end (u 940 and 1578), its top the top of the block in broken lines (v 1827.5); lugs: the base's two hinge lugs, in broken lines; Magpul's underside photo (0933bc534c51) has them at the same places; spring: the hinge's coil spring between the lugs, in broken lines; window: the wheel's window in the arm's rear face (the heavy inner frame); wheel: the wheel's flutes top to bottom (v 1205 to 1472) about the middle plane (u 1257.4); pockets: two oblong pockets in the rear face under the wheel, in broken lines (blind: T.REX's photo 30c2d1cd8140 shows their floors); post_base: the post's root in the notch between the wings; post_stem: the post's blade (34 px between its strokes) up to its flat top at v 863.5) (tools/trace.py)","via":"harvest","note":"The whole sight standing, seen from behind, with the boss at the rifle's left; the cross bolt's head at the right and the post are left out of the outline. The rail's channel between the jaws follows the patent's broken lines."},"front":{"plane":"zy","origin":"the rail's top, on the sight's middle plane","offset":{},"points":[[-0.651,0.169],[-0.65,-0.19],[-0.636,-0.205],[-0.512,-0.225],[-0.469,-0.248],[-0.344,-0.248],[-0.345,-0.192],[-0.355,-0.179],[-0.359,-0.205],[-0.472,-0.202],[-0.469,-0.148],[-0.391,-0.148],[-0.4,-0.132],[-0.398,-0.104],[0.398,-0.104],[0.4,-0.139],[0.385,-0.148],[0.469,-0.148],[0.472,-0.202],[0.354,-0.205],[0.351,-0.182],[0.345,-0.189],[0.344,-0.248],[0.471,-0.248],[0.496,-0.234],[0.562,-0.229],[0.571,-0.219],[0.572,-0.181],[0.572,0.17],[0.571,0.329],[0.527,0.378],[0.527,0.443],[0.517,0.495],[0.443,0.677],[0.43,0.725],[0.4,1.344],[0.348,1.483],[0.341,1.488],[0.283,1.488],[0.27,1.479],[0.246,1.199],[0.221,1.165],[0.186,1.152],[0.065,1.152],[0.061,1.156],[0.058,1.152],[0.016,1.152],[0.013,1.156],[-0.184,1.152],[-0.217,1.162],[-0.24,1.186],[-0.248,1.21],[-0.271,1.481],[-0.282,1.488],[-0.347,1.484],[-0.401,1.34],[-0.425,0.758],[-0.433,0.711],[-0.517,0.494],[-0.526,0.452],[-0.527,0.379],[-0.57,0.332],[-0.571,0.205],[-0.639,0.19]],"features":{"base":[[[0.671,-0.306],[0.671,0.334],[0.571,0.334],[0.472,0.429],[-0.473,0.429],[-0.571,0.334],[-0.678,0.334],[-0.678,-0.306]]],"pad":[[[0.152,1.151],[0.152,1.107],[0.274,1.075],[0.289,1.032],[0.289,0.586],[0.274,0.553],[0.23,0.536],[-0.228,0.536],[-0.271,0.553],[-0.287,0.586],[-0.287,1.032],[-0.271,1.075],[-0.151,1.107],[-0.151,1.151]]],"window":[[[0.223,1.044],[-0.223,1.044],[-0.223,0.703],[0.223,0.703]]],"channel":[[[0.421,0],[-0.421,0],[-0.421,-0.107],[-0.344,-0.187],[-0.344,-0.306],[0.343,-0.306],[0.343,-0.187],[0.421,-0.108]]],"latch":[[[0.421,0.455],[-0.421,0.455],[-0.421,0.216],[0.421,0.216]]]},"scaleRefs":["magpul-mbus-3-front.body_width","magpul-mbus-3-front.height_up"],"inputs":{"magpul-mbus-3-front.body_width":1.143,"magpul-mbus-3-front.height_up":1.488},"tolerance":0.004,"photo":"references/magpul-mbus-3-front 2e54bc6bd40c (US D1,010,056 S (Magpul, 'Gun sight'), FIG. 5 front elevation, 300 dpi)","method":"luminance < 128, inside [620, 730, 1900, 2420], 2 boxes excluded, closing 5 px ×6, holes filled, inset 2 px (half the outline's stroke); frame from the reviewed holes right_rail, left_rail, right_top, left_top (919.1 px/in, rms 0.000 in over 4 points); origin at the photo's frame; Douglas-Peucker at 0.004 in with the extremes kept: 64 points (IoU 0.995 with the full outline); features through the same placement (base: the base's own front view under the arm: below its top edge (v 1744) and its cheeks' chamfered tops (u 731.5, v 1831 to u 822.5, v 1744, solid in this view); pad: the raised pad round the wheel on the arm's front face (the heavy outline) with its neck up to the notch between the wings; window: the wheel's window in the front face, wider than the rear one; channel: the rail's channel between the jaws, as the patent's broken lines draw the rail in it: its ceiling at the hinge block's underside (v 2138.5; the broken line is 3 px lower), its wide part's walls (u 870 and 1643.5), the 45° hooks and the neck (u 941.5 and 1573); latch: the latch's front, in broken lines) (tools/trace.py)","via":"harvest","note":"The whole sight standing, seen from the muzzle (mirrored to the part's frame); the cross bolt's head and the post are left out."},"plan":{"plane":"xz","origin":"the middle of the clamp, on the sight's middle plane","offset":{},"points":[[-0.727,-0.466],[-0.717,-0.492],[-0.687,-0.529],[-0.347,-0.529],[-0.328,-0.519],[-0.317,-0.53],[-0.301,-0.565],[-0.29,-0.572],[-0.157,-0.572],[-0.145,-0.586],[-0.135,-0.64],[-0.123,-0.651],[0.235,-0.651],[0.249,-0.647],[0.26,-0.636],[0.279,-0.54],[0.346,-0.471],[0.346,-0.103],[0.346,0.47],[0.287,0.53],[0.284,0.566],[0.278,0.571],[0.245,0.571],[0.24,0.576],[0.232,0.571],[-0.11,0.571],[-0.116,0.576],[-0.121,0.571],[-0.29,0.572],[-0.299,0.567],[-0.328,0.519],[-0.348,0.528],[-0.689,0.527],[-0.723,0.48]],"features":{"bolt":[[[0.159,-0.434],[-0.036,-0.434],[-0.036,0.431],[0.159,0.431]]]},"scaleRefs":["magpul-mbus-3-front.clamp_length","magpul-mbus-3-front.body_width","magpul-mbus-3-front.length_up"],"inputs":{"magpul-mbus-3-front.body_width":1.143,"magpul-mbus-3-front.clamp_length":0.692,"magpul-mbus-3-front.length_up":1.072},"tolerance":0.004,"photo":"references/magpul-mbus-3-front 7557307d7b4e (US D1,010,056 S (Magpul, 'Gun sight'), FIG. 7 bottom view, 300 dpi)","method":"luminance < 128, inside [720, 860, 1800, 2100], 1 boxes excluded, closing ×7, holes filled, inset 2 px (half the outline's stroke); frame from the reviewed holes front_left, front_right, rear_left, rear_right (919.4 px/in, rms 0.000 in over 4 points); origin at the photo's frame; Douglas-Peucker at 0.004 in with the extremes kept: 34 points (IoU 0.997 with the full outline); features through the same placement (bolt: the cross bolt across the channel, in broken lines (the inner of two outlines: 179 px across; the outer, its shoulder, 208)) (tools/trace.py)","via":"harvest","note":"The sight standing, seen from below, with the boss at the rifle's left; the cross bolt's head is left out."},"top":{"plane":"xz","origin":"the middle of the clamp, on the sight's middle plane","offset":{},"points":[[-0.727,0.47],[-0.725,-0.479],[-0.687,-0.528],[-0.341,-0.528],[-0.328,-0.518],[-0.294,-0.571],[-0.156,-0.571],[-0.145,-0.583],[-0.135,-0.639],[-0.122,-0.65],[0.249,-0.648],[0.26,-0.638],[0.281,-0.539],[0.347,-0.469],[0.347,0.465],[0.344,0.476],[0.287,0.533],[0.283,0.569],[0.24,0.575],[0.235,0.571],[-0.29,0.572],[-0.301,0.566],[-0.317,0.529],[-0.328,0.519],[-0.34,0.529],[-0.685,0.529],[-0.698,0.521]],"features":{"latch":[[[0.316,0.424],[-0.275,0.424],[-0.275,-0.424],[0.316,-0.424]]]},"scaleRefs":["magpul-mbus-3-front.clamp_length","magpul-mbus-3-front.body_width","magpul-mbus-3-front.length_up"],"inputs":{"magpul-mbus-3-front.body_width":1.143,"magpul-mbus-3-front.clamp_length":0.692,"magpul-mbus-3-front.length_up":1.072},"tolerance":0.004,"photo":"references/magpul-mbus-3-front 323366187d99 (US D1,010,056 S (Magpul, 'Gun sight'), FIG. 6 top view, 300 dpi)","method":"luminance < 128, inside [700, 800, 1820, 2140], 1 boxes excluded, closing ×7, holes filled, inset 2 px (half the outline's stroke); frame from the reviewed holes front_right, front_left, rear_right, rear_left (977.0 px/in, rms 0.000 in over 4 points); origin at the photo's frame; Douglas-Peucker at 0.004 in with the extremes kept: 27 points (IoU 0.999 with the full outline); features through the same placement (latch: the release latch on the base's top, in broken lines: its outline's four sides) (tools/trace.py)","via":"harvest","note":"The sight standing, seen from above (mirrored to the part's frame); the cross bolt's head is left out. Drawn 6.3% larger than the other figures."}},"gaps":[{"what":"What Magpul's \"1.38 in wide\" spans: 0.08 to 0.12 in more than the sight measures in its patent and its own photographs","need":"A dimensioned drawing, or a straight end view of the sight on a rail with the rail's width in frame"},{"what":"The sight line's height as a maker's figure (Magpul: \"Standard AR sight height\"); T.REX ARMS' 1.41 in doesn't say what it is measured to","need":"Magpul's figure for the post's tip over the rail, or a square side photo of it standing on a rail"},{"what":"The standing height, the hinge and the clamp's reach rest on the patent's figures at one published length (a seller's row)","need":"A square side photo of the sight standing on a rail, the rail's teeth in frame"},{"what":"The weight's split between the polymer body and its steel (bolt, pins, spring, post)","need":"Nothing published: the centre of mass treats it as one material"}]},"magpul-mbus-3-rear":{"id":"magpul-mbus-3-rear","name":"MBUS 3 Sight – Rear","manufacturer":"Magpul","sku":"MAG1167","url":"https://magpul.com/mbus-3-sight-rear.html","category":"backup_sight","description":"Magpul's MBUS 3 rear sight: a polymer folding backup sight for a Picatinny rail, with a spring-loaded release on the base, tool-less windage and two apertures on an arm that turns over. Black, FDE, ODG.","weight":"magpul-mbus-3-rear.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":["{.clamp_length} / 2 - {.bolt_from_front}",0,0],"note":"On the rail's top at the cross screw's axis: the screw crosses the channel and sits in the rail's slot, so it is what a slot holds. The sight frame's origin is the middle of the clamp (the base's two ends), 0.05 in behind it."},"optical_axis":{"origin":["{.clamp_length} / 2 - {.aperture_behind_front}","{.sight_line_above_rail}",0],"note":"The small aperture's centre, the sight standing (Magpul: \"Center of aperture to top of rail: 1.42 in.\"), in the aperture arm's bar at the arm's rear face."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":"={.clamp_length} - {.bolt_from_front}","clamp_front":"={.bolt_from_front}"},"flips":false,"start":"rear","note":"The base's two ends about the cross screw (0.39 in behind it, 0.29 ahead). It goes on from the rail's rear end with the arm to the rear (the installation sheet: \"slide it onto the rail with Sight Arm to the rear\"; \"It may be necessary to remove the charging handle to install the sight from the rear\"), and the sheet leaves the position to the user (\"When the sight is in the desired position\"). Stowed, the arm reaches 1.47 in behind the hinge (2.06 behind the cross screw): over the rail behind the base and past its rear end over the charging handle, as in Magpul's photo."},"sight_line":{"type":"optic.sight_line","role":"irons","params":{"magnification":"1x"},"flips":false,"note":"An iron sight: it doesn't magnify, and nothing is checked against it (data/interfaces.yaml). Magpul: \"Standard AR sight height for across-the-board compatibility\"."}},"folds":{"up":"up","folded":"folded","note":"Stowed, the arm lies back behind the base with its front face up (Magpul's instruction sheet: \"To stow sight, push down Sight Arm into flat position\"; the patent's FIG. 8)."},"materials":{"body":{"label":"Sight","finish":"polymer","recolorable":true,"color":"magpul-black","sheen":"matte","options":{"black":{"label":"Black","finish":"polymer","color":"magpul-black","sheen":"matte","sku":"MAG1167-BLK","source":"https://www.sportsmans.com/shooting-gear-gun-supplies/gun-parts-accessories/gun-parts-magazines/gun-sights-lasers/magpul-mbus-3-flip-up-rear-sight-black/p/1693789"},"fde":{"label":"FDE","finish":"polymer","color":"magpul-fde","sheen":"matte","sku":"MAG1167-FDE","source":"https://www.primaryarms.com/magpul-mbus-3-rear-sight-flat-dark-earth"},"odg":{"label":"ODG","finish":"polymer","color":"magpul-odg","sheen":"matte","sku":"MAG1167-ODG","source":"https://www.primaryarms.com/magpul-mbus-3-rear-sight-olive-drab-green"}},"default":"black","note":"Magpul: \"Polymer construction\". Its page offers Black, Flat Dark Earth and Olive Drab Green (and shows a Stealth Gray swatch with no product behind it); the page prints MAG1167, and each colour's number is as the seller's page named prints it. The colours are Magpul's as matched on the MOE SL. Three colours today (read 2026-10-06 on the harvested copy of Magpul's page). The base, the arm, the release latch and the windage knob are this colour in every photo (Magpul's FDE gallery 01 and 05.1, T.REX ARMS' FDE and green)."},"hardware":{"label":"Aperture arm and screws","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The aperture arm, the windage screw and its nut, the clamp screw, the hinge's spring and pin: black on the black, the FDE and the ODG sight alike (Magpul's and T.REX ARMS' photos; on the FDE sight the aperture arm, the windage screw's thread either side of it, the clamp screw's slotted head, the two pins and the spring under the latch, with a small black set screw in the FDE knob that isn't drawn). What they are made of isn't stated; drawn as black steel. A black on steel isn't fitted to a photo: the colour is the placeholder black."}},"components":{},"geometry":{"components":{"up":"magpul-mbus-3-rear.up.glb","folded":"magpul-mbus-3-rear.folded.glb"},"approximations":["Built from Magpul's design patent for it (US D1,010,057 S: the left and rear elevations and the top plan, each piece's own outline taken from the figure), at the scale Magpul's width at the widest point sets (1.38 in); the aperture's centre then stands 1.427 in above the rail's top against Magpul's 1.42. The patent's broken-line parts (the channel under the rail's top, the base's knuckles and the hinge's spring, the clamp screw's head) are drawn as it has them, and the channel then made the standard's head in section (MIL-STD-1913's, since 2026-10-12) from the rail's top down to the lower gauge line: the patent's is a few hundredths wider and square over a rail's upper faces.","Stowed is the standing sight with its arm turned a quarter turn about the hinge: 2.35 in long, the arm's top 0.44 in above the rail and the windage knob's rim 0.52, where Magpul says ~0.55 in. In Magpul's photo of it stowed the arm lies about 3° past flat.","The base and the arm are each their side outline cut by their outline from behind, so they are square across where the real ones are rounded; the wall between the wings is drawn at the arm's mid-thickness and as thick as the aperture arm's bar (no view shows its section); the aperture arm's flanges and the windage screw's nut are plain discs; the windage knob's eight flutes are cut a sixteenth of its radius deep (FIG. 3 shows eight, not their depth).","The aperture arm is drawn with the small aperture up. Its two apertures are a seller's diameters (T.REX ARMS: 0.063 and 0.19 in); Magpul states none. The small one's countersink is the ring the patent draws about it on the bar's rear face, down to the aperture at the bar's mid-thickness (no view gives its depth).","The hinge pin is a plain pin at the size of the patent's broken circle about the hinge (0.096 in), its ends 0.006 in proud of the arm's lugs.","The release latch is a seam in the base's top along the patent's broken-line outline of it (FIG. 6), as wide and as deep as the edges are broken (0.012 in): no view gives the seam a size.","The clamp screw's head has its hex socket at the installation sheet's key size (1/8 in across the flats), half as deep as the head stands proud of the base (no view gives its depth); its screwdriver slot isn't drawn.","Not drawn: the Magpul mark on the latch, the MBUS lettering, the bar's ribs (along it on the product, across it in the patent) and windage marks, the cross screw's shank in the channel, the set screw in the knob. Edges broken at 0.012 in."],"ledger":["magpul-mbus-3-rear.length","magpul-mbus-3-rear.width","magpul-mbus-3-rear.height","magpul-mbus-3-rear.height_up","magpul-mbus-3-rear.sight_line_above_rail","magpul-mbus-3-rear.clamp_length","magpul-mbus-3-rear.clamp_below_rail","magpul-mbus-3-rear.bolt_from_front","magpul-mbus-3-rear.aperture_behind_front","magpul-mbus-3-rear.aperture_small_d","magpul-mbus-3-rear.aperture_large_d","magpul-mbus-3-rear.clamp_screw_hex"]},"profiles":{"rear":{"plane":"zy","origin":"midway between the wings' outer faces (the rail's centre line); the clamp's lower edge, offset to the rail's top","offset":{"y":"clamp_bottom_y"},"points":[[-0.667,0.063],[-0.654,0.046],[-0.527,0.025],[-0.484,0.001],[-0.358,0],[-0.353,0.002],[-0.354,0.062],[-0.359,0.067],[-0.363,0.046],[-0.484,0.049],[-0.481,0.096],[-0.391,0.097],[-0.415,0.125],[-0.412,0.15],[0.414,0.15],[0.412,0.113],[0.393,0.101],[0.482,0.096],[0.485,0.052],[0.365,0.049],[0.361,0.069],[0.354,0.061],[0.354,0.002],[0.473,0],[0.509,0.016],[0.583,0.023],[0.589,0.07],[0.587,0.593],[0.542,0.643],[0.539,0.774],[0.488,0.924],[0.484,1.05],[0.507,1.08],[0.51,1.107],[0.656,1.116],[0.694,1.136],[0.712,1.153],[0.713,1.522],[0.705,1.538],[0.662,1.563],[0.507,1.576],[0.506,1.604],[0.484,1.631],[0.483,1.81],[0.439,1.937],[0.43,1.949],[0.335,1.949],[0.31,1.917],[0.305,1.433],[0.3,1.428],[0.166,1.433],[0.165,1.79],[0.146,1.828],[0.102,1.846],[-0.104,1.846],[-0.127,1.84],[-0.147,1.826],[-0.161,1.805],[-0.166,1.774],[-0.165,1.433],[-0.301,1.429],[-0.31,1.918],[-0.332,1.949],[-0.431,1.949],[-0.483,1.807],[-0.484,0.946],[-0.495,0.894],[-0.525,0.823],[-0.537,0.777],[-0.541,0.642],[-0.586,0.596],[-0.587,0.467],[-0.653,0.453],[-0.666,0.442]],"features":{"yoke":[[[-0.334,1.949],[-0.434,1.949],[-0.439,1.933],[-0.466,1.854],[-0.483,1.805],[-0.483,0.96],[-0.485,0.938],[-0.489,0.916],[-0.496,0.893],[-0.505,0.871],[-0.514,0.849],[-0.523,0.826],[-0.53,0.804],[-0.535,0.782],[-0.539,0.759],[-0.54,0.715],[-0.54,0.301],[-0.526,0.29],[-0.502,0.273],[-0.488,0.266],[-0.333,0.266],[-0.333,0.58],[-0.327,0.596],[-0.311,0.603],[0.313,0.603],[0.329,0.596],[0.335,0.58],[0.335,0.266],[0.489,0.266],[0.504,0.273],[0.527,0.29],[0.541,0.301],[0.541,0.715],[0.54,0.759],[0.537,0.782],[0.531,0.804],[0.525,0.826],[0.516,0.849],[0.507,0.871],[0.498,0.893],[0.491,0.916],[0.487,0.938],[0.484,0.96],[0.484,1.805],[0.468,1.854],[0.441,1.933],[0.436,1.949],[0.335,1.949],[0.322,1.933],[0.311,1.854],[0.308,1.698],[0.306,1.343],[0.302,0.983],[0.3,0.916],[0.299,0.893],[0.294,0.871],[0.282,0.849],[0.264,0.832],[0.238,0.822],[-0.236,0.822],[-0.262,0.832],[-0.28,0.849],[-0.292,0.871],[-0.297,0.893],[-0.298,0.916],[-0.3,0.983],[-0.304,1.343],[-0.306,1.698],[-0.31,1.854],[-0.32,1.933]]],"web":[[[-0.315,1.123],[0.316,1.123],[0.316,0.804],[-0.315,0.804]]],"plate":[[[0.166,0.882],[0.164,0.867],[0.158,0.854],[0.147,0.844],[0.134,0.837],[0.12,0.835],[-0.118,0.835],[-0.133,0.837],[-0.146,0.844],[-0.156,0.854],[-0.163,0.867],[-0.165,0.882],[-0.165,1.799],[-0.163,1.814],[-0.156,1.827],[-0.146,1.837],[-0.133,1.844],[-0.118,1.846],[0.12,1.846],[0.134,1.844],[0.147,1.837],[0.158,1.827],[0.164,1.814],[0.166,1.799]]],"aperture_small":[[[0.037,1.679],[0.036,1.686],[0.034,1.693],[0.031,1.699],[0.026,1.705],[0.021,1.709],[0.015,1.713],[0.008,1.715],[0.001,1.715],[-0.006,1.715],[-0.013,1.713],[-0.019,1.709],[-0.024,1.705],[-0.029,1.699],[-0.032,1.693],[-0.034,1.686],[-0.035,1.679],[-0.034,1.673],[-0.032,1.666],[-0.029,1.66],[-0.024,1.654],[-0.019,1.65],[-0.013,1.646],[-0.006,1.644],[0.001,1.644],[0.008,1.644],[0.015,1.646],[0.021,1.65],[0.026,1.654],[0.031,1.66],[0.034,1.666],[0.036,1.673]]],"aperture_large":[[[0.097,0.999],[0.095,1.018],[0.09,1.037],[0.081,1.053],[0.069,1.068],[0.054,1.08],[0.037,1.089],[0.019,1.095],[0,1.097],[-0.019,1.095],[-0.037,1.089],[-0.054,1.08],[-0.069,1.068],[-0.081,1.053],[-0.09,1.037],[-0.095,1.018],[-0.097,0.999],[-0.095,0.98],[-0.09,0.962],[-0.081,0.945],[-0.069,0.931],[-0.054,0.919],[-0.037,0.909],[-0.019,0.904],[0,0.902],[0.019,0.904],[0.037,0.909],[0.054,0.919],[0.069,0.931],[0.081,0.945],[0.09,0.962],[0.095,0.98]]],"aperture_ring":[[[0.065,1.679],[0.064,1.692],[0.06,1.704],[0.054,1.715],[0.046,1.724],[0.037,1.732],[0.025,1.738],[0.014,1.742],[0.001,1.743],[-0.011,1.742],[-0.023,1.738],[-0.034,1.732],[-0.044,1.724],[-0.052,1.715],[-0.058,1.704],[-0.061,1.692],[-0.063,1.679],[-0.061,1.667],[-0.058,1.655],[-0.052,1.644],[-0.044,1.634],[-0.034,1.627],[-0.023,1.621],[-0.011,1.617],[0.001,1.616],[0.014,1.617],[0.025,1.621],[0.037,1.627],[0.046,1.634],[0.054,1.644],[0.06,1.655],[0.064,1.667]]],"windage_screw":[[[-0.465,1.422],[0.507,1.422],[0.507,1.262],[-0.465,1.262]]],"knob_collar":[[[0.484,1.633],[0.493,1.633],[0.507,1.616],[0.507,1.068],[0.493,1.051],[0.484,1.051]]],"knob_grip":[[[0.507,1.573],[0.664,1.567],[0.713,1.541],[0.713,1.143],[0.664,1.117],[0.507,1.111]]],"flange_left":[[[-0.143,1.549],[-0.068,1.549],[-0.068,1.135],[-0.143,1.135]]],"flange_right":[[[0.07,1.549],[0.145,1.549],[0.145,1.135],[0.07,1.135]]],"traveller":[[[-0.068,1.476],[0.07,1.476],[0.07,1.208],[-0.068,1.208]]],"clamp_boss":[[[-0.586,0.465],[-0.667,0.443],[-0.667,0.052],[-0.586,0.03]]],"screw_head":[[[0.587,0.425],[0.669,0.425],[0.669,0.07],[0.587,0.07]]],"base":[[[-0.488,0.697],[-0.587,0.597],[-0.587,0.068],[-0.485,0],[-0.353,0],[-0.353,0.064],[-0.422,0.134],[-0.437,0.149],[-0.448,0.159],[-0.448,0.229],[-0.441,0.245],[-0.424,0.253],[0.424,0.253],[0.441,0.245],[0.448,0.229],[0.448,0.159],[0.437,0.149],[0.422,0.134],[0.353,0.064],[0.353,0],[0.485,0],[0.587,0.068],[0.587,0.597],[0.488,0.697]]],"knuckle_left":[[[-0.333,0.603],[-0.178,0.603],[-0.178,0.253],[-0.333,0.253]]],"knuckle_right":[[[0.178,0.603],[0.334,0.603],[0.334,0.253],[0.178,0.253]]],"spring":[[[-0.164,0.603],[0.166,0.603],[0.166,0.357],[-0.164,0.357]]],"rail_top":[[[-0.424,0.253],[0.424,0.253],[0.424,0.25],[-0.424,0.25]]]},"scaleRefs":["magpul-mbus-3-rear.width"],"inputs":{"magpul-mbus-3-rear.width":1.38},"tolerance":0.004,"photo":"references/magpul-mbus-3-rear 1e9f20f4f5f7 (US D1,010,057 S (Magpul, 'Gun sight'), FIG. 4 rear elevation, deployed; the patent office's copy, page 6, 300 dpi)","method":"luminance < 128, inside [560, 620, 1960, 2480], closing 21 px ×1, largest piece, holes filled, inset 2 px (half the outline's stroke); scale from magpul-mbus-3-rear.width = 1.38 in (x-extent 1235 px → 894.9 px/in); origin at x center, y min of the outline (x over 0.0–0.07 of the height from the top); Douglas-Peucker at 0.004 in with the extremes kept: 74 points (IoU 0.996 with the full outline); the one published size this view's outline spans is the width; the second, the aperture's centre above the rail's top (1.42 in), is inside the outline: at this scale it reads 1.427 (the ledger's sight_line_above_rail, measurement patent); features through the same placement (yoke: the sight arm from behind: its wings, its flare and its two lugs, through the strokes read on rows of the figure (the left side, mirrored about the middle between the wings' outer faces: the right side's strokes are within 1 px of that); the opening between the wings along its innermost line; the window between the lugs along FIG. 4's broken-line box; web: the wall between the wings below the windage screw: its top edge (the stroke at row 1414.5) down into the arm's body; plate: the aperture arm's bar: the rounded rectangle its strokes draw; aperture_small: the small aperture (the circle its strokes close; the centroid is its centre); aperture_large: the large aperture, below the windage screw in this state (the circle its strokes close); aperture_ring: the ring about the small aperture on the bar's rear face (the region between its stroke and the aperture's is 110 px across): a countersink; windage_screw: the windage screw across the wings: FIG. 4's broken thread lines either side of the bar, 144 px across, on the knob's axis (row 1218.5); knob_collar: the windage knob's collar against the right wing: 520 px across at the wing, chamfered to 490; knob_grip: the windage knob's fluted grip, to its end (the figure's right extreme); flange_left: the aperture arm's left flange about the windage screw (FIG. 5's two bars, 63 px wide and 371 tall, 62 px either side of the middle), placed here across the sight; flange_right: its right flange; traveller: the nut on the windage screw between the flanges (the bulge between FIG. 5's bars); clamp_boss: the clamp's boss on the left: 390 px across at the base's wall, 350 at its face (the figure's left extreme); screw_head: the clamp screw's head on the right, in broken lines (the hex socket of FIG. 3 on its axis): 317 px across, 73 proud of the base's wall; base: the base from behind: its top and the chamfers to its side walls (FIG. 5's strokes at rows 1830 to 1900, mirrored onto this sheet), the walls, the jaws, and the channel for the rail in broken lines (its ceiling at row 2193.5 is the rail's top); knuckle_left: the base's left knuckle, in the window between the arm's lugs (broken lines); knuckle_right: its right knuckle; spring: the hinge's spring between the knuckles (the broken-line coil's extent: 220 px across, about the hinge's axis); rail_top: the rail's top: the channel's ceiling, the broken line at row 2193.5) (tools/trace.py)","via":"harvest","note":"The whole sight from behind, standing, the windage knob on the right. The broken lines (the channel under the rail's top, the clamp screw's head, the windage screw's thread) are closed into the outline (a 21 px closing: less leaves the body open to the channel through their gaps); the model is built from the features, each piece's own outline."},"side":{"plane":"xy","origin":"the base's front end; the clamp's lower edge. Offset to the clamp's middle and the rail's top","offset":{"x":"clamp_front_x","y":"clamp_bottom_y"},"points":[[-1.176,1.364],[-1.173,1.299],[-1.159,1.239],[-1.135,1.19],[-1.101,1.144],[-1.101,0.463],[-1.085,0.397],[-1.067,0.363],[-1.025,0.316],[-0.93,0.255],[-0.718,0.255],[-0.71,0.242],[-0.671,0.09],[-0.657,0.059],[-0.615,0.016],[-0.557,0],[-0.09,0.001],[-0.05,0.016],[-0.023,0.04],[-0.008,0.068],[0,0.102],[0,0.229],[-0.011,0.321],[-0.075,0.563],[-0.102,0.605],[-0.125,0.626],[-0.179,0.65],[-0.395,0.687],[-0.489,0.698],[-0.601,0.697],[-0.639,0.665],[-0.653,0.635],[-0.655,0.582],[-0.66,0.577],[-0.671,0.582],[-0.671,1.145],[-0.634,1.194],[-0.601,1.28],[-0.596,1.347],[-0.606,1.416],[-0.641,1.497],[-0.698,1.563],[-0.726,1.807],[-0.748,1.857],[-0.792,1.888],[-1.028,1.949],[-1.047,1.948],[-1.071,1.936],[-1.09,1.914],[-1.099,1.888],[-1.101,1.535],[-1.13,1.498],[-1.152,1.457]],"features":{"arm":[[[-0.669,0.465],[-0.669,0.517],[-0.673,0.527],[-0.673,0.533],[-0.669,0.536],[-0.669,1.177],[-0.673,1.3],[-0.679,1.4],[-0.687,1.467],[-0.687,1.481],[-0.691,1.498],[-0.691,1.513],[-0.696,1.547],[-0.701,1.603],[-0.715,1.708],[-0.72,1.756],[-0.73,1.823],[-0.741,1.849],[-0.749,1.859],[-0.767,1.876],[-0.784,1.885],[-1.009,1.947],[-1.025,1.949],[-1.051,1.947],[-1.068,1.939],[-1.086,1.921],[-1.095,1.903],[-1.102,1.868],[-1.102,0.531],[-1.097,0.528],[-1.102,0.518],[-1.102,0.474],[-1.096,0.43],[-1.094,0.427],[-1.094,0.422],[-1.085,0.396],[-1.076,0.377],[-1.063,0.356],[-1.043,0.331],[-1.014,0.306],[-0.974,0.283],[-0.945,0.273],[-0.936,0.272],[-0.934,0.269],[-0.902,0.265],[-0.871,0.265],[-0.839,0.269],[-0.805,0.279],[-0.764,0.301],[-0.738,0.322],[-0.709,0.355],[-0.692,0.383],[-0.676,0.424]]],"base":[[[0,0.099],[0,0.237],[-0.006,0.291],[-0.011,0.324],[-0.027,0.377],[-0.039,0.431],[-0.044,0.441],[-0.045,0.452],[-0.049,0.462],[-0.049,0.469],[-0.053,0.476],[-0.07,0.552],[-0.085,0.584],[-0.095,0.598],[-0.109,0.614],[-0.128,0.629],[-0.137,0.633],[-0.139,0.636],[-0.177,0.65],[-0.25,0.663],[-0.253,0.665],[-0.294,0.671],[-0.299,0.673],[-0.463,0.696],[-0.484,0.698],[-0.592,0.697],[-0.604,0.694],[-0.619,0.686],[-0.635,0.672],[-0.649,0.649],[-0.655,0.622],[-0.656,0.472],[-0.66,0.434],[-0.671,0.401],[-0.678,0.386],[-0.678,0.383],[-0.687,0.369],[-0.691,0.36],[-0.704,0.344],[-0.712,0.327],[-0.719,0.302],[-0.72,0.279],[-0.716,0.259],[-0.713,0.252],[-0.712,0.242],[-0.71,0.24],[-0.701,0.199],[-0.696,0.191],[-0.696,0.185],[-0.679,0.128],[-0.671,0.088],[-0.653,0.051],[-0.626,0.022],[-0.604,0.01],[-0.583,0.003],[-0.559,0],[-0.096,0],[-0.066,0.007],[-0.052,0.016],[-0.049,0.016],[-0.025,0.037],[-0.008,0.065]]],"hinge":[[[-1.066,0.481],[-1.063,0.517],[-1.053,0.551],[-1.036,0.582],[-1.013,0.609],[-0.986,0.632],[-0.955,0.649],[-0.921,0.659],[-0.885,0.662],[-0.85,0.659],[-0.816,0.649],[-0.785,0.632],[-0.757,0.609],[-0.735,0.582],[-0.718,0.551],[-0.708,0.517],[-0.704,0.481],[-0.708,0.446],[-0.718,0.412],[-0.735,0.381],[-0.757,0.353],[-0.785,0.331],[-0.816,0.314],[-0.85,0.304],[-0.885,0.3],[-0.921,0.304],[-0.955,0.314],[-0.986,0.331],[-1.013,0.353],[-1.036,0.381],[-1.053,0.412],[-1.063,0.446]]],"windage":[[[-1.068,1.343],[-1.065,1.378],[-1.054,1.412],[-1.038,1.443],[-1.015,1.471],[-0.987,1.493],[-0.956,1.51],[-0.922,1.521],[-0.887,1.524],[-0.851,1.521],[-0.817,1.51],[-0.786,1.493],[-0.758,1.471],[-0.736,1.443],[-0.719,1.412],[-0.709,1.378],[-0.705,1.343],[-0.709,1.307],[-0.719,1.273],[-0.736,1.242],[-0.758,1.214],[-0.786,1.192],[-0.817,1.175],[-0.851,1.165],[-0.887,1.161],[-0.922,1.165],[-0.956,1.175],[-0.987,1.192],[-1.015,1.214],[-1.038,1.242],[-1.054,1.273],[-1.065,1.307]]],"bolt":[[[-0.467,0.248],[-0.464,0.282],[-0.454,0.314],[-0.438,0.345],[-0.416,0.371],[-0.39,0.393],[-0.36,0.409],[-0.327,0.419],[-0.293,0.422],[-0.259,0.419],[-0.226,0.409],[-0.196,0.393],[-0.17,0.371],[-0.148,0.345],[-0.132,0.314],[-0.122,0.282],[-0.119,0.248],[-0.122,0.214],[-0.132,0.181],[-0.148,0.151],[-0.17,0.124],[-0.196,0.103],[-0.226,0.087],[-0.259,0.077],[-0.293,0.073],[-0.327,0.077],[-0.36,0.087],[-0.39,0.103],[-0.416,0.124],[-0.438,0.151],[-0.454,0.181],[-0.464,0.214]]],"hinge_pin":[[[-0.933,0.481],[-0.932,0.49],[-0.929,0.5],[-0.925,0.508],[-0.919,0.515],[-0.912,0.521],[-0.904,0.525],[-0.895,0.528],[-0.885,0.529],[-0.876,0.528],[-0.867,0.525],[-0.859,0.521],[-0.851,0.515],[-0.846,0.508],[-0.841,0.5],[-0.838,0.49],[-0.837,0.481],[-0.838,0.472],[-0.841,0.463],[-0.846,0.455],[-0.851,0.447],[-0.859,0.441],[-0.867,0.437],[-0.876,0.434],[-0.885,0.433],[-0.895,0.434],[-0.904,0.437],[-0.912,0.441],[-0.919,0.447],[-0.925,0.455],[-0.929,0.463],[-0.932,0.472]]],"plate":[[[-1.028,1.846],[-1.099,1.846],[-1.099,0.835],[-1.028,0.835]]],"knuckle":[[[-0.681,0.603],[-0.885,0.603],[-0.909,0.601],[-0.932,0.594],[-0.953,0.582],[-0.971,0.567],[-0.986,0.549],[-0.998,0.528],[-1.005,0.505],[-1.007,0.481],[-1.007,0.253],[-0.681,0.253]]]},"scaleRefs":["magpul-mbus-3-rear.overall_height_up"],"inputs":{"magpul-mbus-3-rear.overall_height_up":1.949},"tolerance":0.004,"photo":"references/magpul-mbus-3-rear 615a86af0b47 (US D1,010,057 S (Magpul, 'Gun sight'), FIG. 2 left elevation, deployed; the patent office's copy, page 4, 300 dpi)","method":"luminance < 128, inside [680, 690, 1840, 2520], closing ×2, largest piece, holes filled, inset 2 px (half the outline's stroke); scale from magpul-mbus-3-rear.overall_height_up = 1.949 in (y-extent 1744 px → 894.8 px/in); origin at x max, y min of the outline; Douglas-Peucker at 0.004 in with the extremes kept: 53 points (IoU 0.995 with the full outline); scaled by the overall height the rear elevation measures: the patent's elevations are all 1748 px tall on their sheets; features through the same placement (arm: the sight arm's outer outline: the three regions its strokes close, joined, to the strokes' centres; base: the base's outer outline with the clamp's boss on it: the regions its strokes close, to the strokes' centres; hinge: the round lower end of the arm's side panel (a circle fitted to its stroke, rms 0.4 px): the hinge's axis is its centre; windage: the round upper bulge of the arm's side panel (a circle fitted to its stroke): the windage screw's axis is its centre; bolt: the clamp boss's face (a circle fitted to its stroke): the cross bolt's axis is its centre; hinge_pin: the hinge pin's end on the arm's lug: the innermost broken circle about the hinge's axis (its dashes on row 2045 at 1480 and 1565.5: 85.6 px across); plate: the aperture arm's bar seen edge on: FIG. 6 has it 1651 to 1717 along the rail (against the arm's rear face), FIG. 4 767.5 to 1672.5 up the sheet (this sheet is 56 rows lower); knuckle: the base's knuckles behind the arm's lugs, hidden in this view: FIG. 4's broken-line box (its top, 1880 there) rounded about the hinge's axis, down to the rail's top) (tools/trace.py)","via":"harvest","note":"The left elevation, turned to face the muzzle: the base ahead, the arm standing at its rear on the hinge. The windage knob is behind the arm in this view (the two arcs either side of it)."},"plan":{"plane":"xz","origin":"the base's front end; the middle of the figure across (the clamp's boss to the knob's end, which isn't the rail's centre line: the model centres the base's own outline on the rail)","offset":{"x":"clamp_front_x"},"points":[[-1.171,0.393],[-1.166,0.379],[-1.098,0.306],[-1.1,-0.51],[-1.073,-0.553],[-1.055,-0.565],[-0.705,-0.565],[-0.69,-0.552],[-0.662,-0.606],[-0.652,-0.61],[-0.512,-0.609],[-0.504,-0.617],[-0.493,-0.679],[-0.48,-0.69],[-0.101,-0.688],[-0.088,-0.675],[-0.068,-0.577],[0,-0.505],[-0.001,0],[0,0.461],[-0.06,0.521],[-0.066,0.562],[-0.109,0.567],[-0.113,0.563],[-0.468,0.563],[-0.472,0.567],[-0.477,0.563],[-0.648,0.563],[-0.654,0.57],[-0.66,0.646],[-0.696,0.69],[-1.063,0.69],[-1.074,0.686],[-1.103,0.638],[-1.112,0.49],[-1.118,0.484],[-1.141,0.485],[-1.166,0.469]],"features":{"base":[[[0,-0.508],[0,0.462],[-0.003,0.463],[-0.003,0.467],[-0.059,0.52],[-0.069,0.523],[-0.094,0.534],[-0.126,0.555],[-0.132,0.563],[-0.139,0.564],[-0.652,0.564],[-0.648,0.484],[-0.623,0.484],[-0.623,0.481],[-0.617,0.477],[-0.605,0.471],[-0.599,0.461],[-0.596,0.359],[-0.607,0.345],[-0.625,0.334],[-0.631,0.329],[-0.632,0.326],[-0.653,0.314],[-0.666,0.302],[-0.666,-0.51],[-0.674,-0.524],[-0.688,-0.542],[-0.689,-0.55],[-0.664,-0.604],[-0.654,-0.61],[-0.139,-0.61],[-0.132,-0.609],[-0.099,-0.582],[-0.069,-0.568],[-0.059,-0.566],[-0.008,-0.518],[-0.003,-0.513],[-0.003,-0.509]]],"latch":[[[-0.667,-0.395],[-0.664,-0.414],[-0.655,-0.431],[-0.641,-0.445],[-0.624,-0.453],[-0.605,-0.456],[-0.101,-0.456],[-0.082,-0.453],[-0.065,-0.445],[-0.051,-0.431],[-0.043,-0.414],[-0.04,-0.395],[-0.04,0.355],[-0.043,0.374],[-0.051,0.391],[-0.065,0.404],[-0.082,0.413],[-0.101,0.416],[-0.605,0.416],[-0.624,0.413],[-0.641,0.404],[-0.655,0.391],[-0.664,0.374],[-0.667,0.355]]]},"scaleRefs":["magpul-mbus-3-rear.width"],"inputs":{"magpul-mbus-3-rear.width":1.38},"tolerance":0.004,"photo":"references/magpul-mbus-3-rear baf4699b50f5 (US D1,010,057 S (Magpul, 'Gun sight'), FIG. 6 top plan, deployed; the patent office's copy, page 8, 300 dpi)","method":"luminance < 128, inside [680, 900, 1840, 2260], closing ×2, largest piece, holes filled, inset 2 px (half the outline's stroke); scale from magpul-mbus-3-rear.width = 1.38 in (y-extent 1237 px → 896.4 px/in); origin at x max, y center of the outline; Douglas-Peucker at 0.004 in with the extremes kept: 38 points (IoU 0.997 with the full outline); features through the same placement (base: the base from above: its top face and the two shoulders beside it (the regions their strokes close, joined, to the strokes' centres); its rear end is ragged where the arm stands over it; latch: the release latch in the base's top: the outer broken-line outline) (tools/trace.py)","via":"harvest","note":"The sight from above, standing, turned so the muzzle is at +x and the windage knob at +z."}},"gaps":[{"what":"A length from Magpul (its page states none; a seller's 2.43 in is 0.08 in more than the patent's figures and Magpul's photo give)","need":"Magpul's own stowed length, or a straight side photo of it stowed with a scale in its plane"},{"what":"What the stowed height is measured to: Magpul's ~0.55 in against 0.52 in to the windage knob's rim on the patent's figures and in Magpul's photo","need":"A dimensioned drawing, or a straight end view of it stowed on a rail"},{"what":"The aperture arm's ribs (they run along the bar on the product and across it in the patent), the windage marks on the arm's rear face, the MBUS lettering and the Magpul mark","need":"Surface detail; not modelled"},{"what":"What the hardware is made of and its finish","need":"A statement from Magpul"}]},"magpul-mbus-pro-front":{"id":"magpul-mbus-pro-front","name":"MBUS Pro Sight – Front","manufacturer":"Magpul","sku":"MAG275","url":"https://magpul.com/firearm-accessories/sights/mbus-pro/mbus-pro-sight-front.html","category":"backup_sight","description":"Magpul's MBUS Pro Sight – Front (MAG275): an all-steel folding front sight for a Picatinny rail, with a post selectable between two widths and a toolless elevation knob. Black only. It folds down to the rear.","weight":"magpul-mbus-pro-front.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":["{.clamp_length} / 2 - {.screw_behind_front}",0,0],"note":"On the rail's top at the cross bolt's axis: the bolt crosses the channel under the rail's top and is the sight's recoil lug, so it is what a slot holds (as its rear sight and the MBUS 3 pair are placed). The sight's frame has its origin at the middle of the base (the saddle under the hinge and the clamp behind it), 0.20 in ahead of the bolt; +x toward the muzzle, +y up. The hinge is at the front; the arm folds down to the rear and, folded, reaches 0.60 in behind the base."},"optical_axis":{"origin":[0,"{.sight_line_above_rail}",0],"note":"The sight line it has standing: the post's tip, at the height its rear sight's aperture has (the post screws up and down for elevation)."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":"={.clamp_length} - {.screw_behind_front}","clamp_front":"={.screw_behind_front}"},"flips":false,"start":"front","note":"The base's two ends about the cross bolt: 0.72 in ahead of it (the saddle under the hinge), 0.32 behind. As far forward as it goes, the arm folding to the rear: \"Position the sight so the sight arm folds down to the rear. For best results, mount sight as far forward as possible.\" On the receiver's plane: \"NOTE: MBUS Pro Front Sight must be mounted on same-plane as rear sight. Do not install front sight above or below receiver rail level (ex: some railed gas blocks).\" Its cross bolt is its recoil lug: \"Push Sight forward in recess until recoil lug is engaged.\" A 10-24 screw, 1/8 in hex or a flat blade: \"DO NOT OVER-TIGHTEN: Do not exceed 25 in-lbs as this may cause damage to the rail or sight.\" (Magpul's sheet 072-0074-A, its one page.) Magpul's page: \"Mounts on any MIL-STD-1913 Picatinny/STANAG 4694 rail including receiver-height gas blocks.\""},"sight_line":{"type":"optic.sight_line","role":"irons","params":{"magnification":"1x"},"flips":false,"note":"An iron sight: it doesn't magnify, and nothing is checked against it (data/interfaces.yaml)."}},"folds":{"up":"up","folded":"folded","note":"Detents hold it up and folded (Magpul's page: \"Detents secure the sight and elevation knob when it’s stowed or deployed\")."},"materials":{"body":{"label":"Sight","finish":"nitride","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"nitride","color":"placeholder-black","sku":"MAG275-BLK","source":"https://magpul.com/firearm-accessories/sights/mbus-pro/mbus-pro-sight-front.html"}},"default":"black","note":"Steel, black, the one colour (Magpul's page has Black alone under Color, MAG275_RET_BLK_ in its data, and prints NSN: MAG275-BLK 1005-01-629-5549; sellers list MAG275-BLK). Magpul: \"All-steel construction with a QPQ nitride finish for extreme durability in all conditions\", and \"THE ALL-STEEL CONSTRUCTION IS FINISHED WITH A QPQ SALT BATH NITRIDE PROCESS\": drawn as black nitride. Wing Tactical's page disagrees on the finish: \"Case hardened and coated with Mil-Spec manganese phosphate finish\"; the maker's words are taken. Piece by piece on Magpul's older studio shot (2000 px) and Wing Tactical's five: the base, the arm, the elevation knob, the post, the cross bolt and its nut and the hinge pin are one black, nothing bright among them. One slot. A nitride black isn't fitted to a photo: the colour is the placeholder black."}},"components":{},"geometry":{"components":{"up":"magpul-mbus-pro-front.up.glb","folded":"magpul-mbus-pro-front.folded.glb"},"approximations":["Built from Magpul's design patent (US D705,890 S, the sight folded: FIG. 6 side, FIG. 3 front, FIG. 7 top plan), at the scale Magpul's stowed length sets (1.63 in). At that scale the patent's knob stands 0.455 in above the rail folded (Magpul: ~0.43 in. max) and its wings 1.578 in standing (Magpul: 1.56). A rail of .835 in in the patent's clamp, and Recoil's 2015 figure for the length (1.57 in), would make the whole sight 4% smaller; nothing on file settles which.","Standing is the folded arm turned a quarter turn about the hinge pin's axis, as the patent's FIG. 9 and 10 and Magpul's photos show it.","The rail's top is taken at the roof of the clamp's channel (the base resting on the rail). The channel is the saddle's section along the whole base (0.88 in between its walls: 0.05 in more than a rail at this scale), with the two jaws' lips under the rail's edges along the clamp, as the front elevation shows them through the saddle. Since 2026-10-12 it is filled in to the standard's head in section (MIL-STD-1913's) from the rail's top down to the lower gauge line, so the base bears on a rail's upper faces, and the left lip is cut back where the patent's leans 0.003 in into a rail's lower face. The clamp's separate bar on the left is drawn as part of the base.","The deck under the arm is hidden in every folded view: it is taken at the level of the hinge barrel's underside, with a notch in the base's rear end under the elevation knob (the bottom plan, FIG. 8, shows one) as wide as the knob needs. The arm's hinge barrel is a round about the pin as high as the arm's face.","The elevation knob is a drum of twelve flutes on the post's axis; the pocket in the arm's face is as deep as the knob stands proud of it; the post's housing, from the knob to the hinge, is a round of the hinge barrel's radius on that axis (Magpul's photos show it standing out of the arm's rear face). The post is the plan view's blade and cone, flat, its tip at the sight line (1.41 in: Magpul's photo has it there; the patent draws it 0.045 in higher).","The cross bolt is where the patent draws it, 0.717 in behind the base's front end; Magpul's side photo has its head at 0.712 (the ledger's .screw_behind_front: until 2026-10-05 this note had it 0.07 in further back, which the photo doesn't bear out). The hinge pin's two pockets are cut square to the sides, as far in as their upper rims meet the shoulders; the two ridges are crowned as the front elevation's top is. Not drawn: the grooves on the wings' lobes, the pockets in the arm's rear face, the UP mark and MBUS PRO lettering. The cross bolt's head has its slot as the front elevation draws it and a 1/8 in hex socket (the sheet's key size) as deep as it is wide. Edges broken at 0.006 in."],"ledger":["magpul-mbus-pro-front.length","magpul-mbus-pro-front.width","magpul-mbus-pro-front.height","magpul-mbus-pro-front.height_up","magpul-mbus-pro-front.sight_line_above_rail","magpul-mbus-pro-front.clamp_length","magpul-mbus-pro-front.screw_behind_front","magpul-mbus-pro-front.clamp_depth","magpul-mbus-pro-front.folded_overall_height","magpul-mbus-pro-front.pivot_x","magpul-mbus-pro-front.pivot_y","magpul-mbus-pro-front.arm_reach","magpul-mbus-pro-front.knob_diameter","magpul-mbus-pro-front.post_width_match","magpul-mbus-pro-front.screw_hex"]},"profiles":{"side":{"plane":"xy","origin":"the photo's frame","offset":{},"points":[[-1.113,0.054],[-1.101,0.038],[-1.067,0.017],[-0.606,0.017],[-0.572,0.03],[-0.545,0.069],[-0.519,0.069],[-0.513,0.063],[-0.519,0.029],[-0.517,-0.166],[-0.504,-0.195],[-0.477,-0.211],[0.471,-0.213],[0.504,-0.199],[0.518,-0.175],[0.518,0.112],[0.51,0.137],[0.496,0.155],[0.306,0.345],[0.254,0.374],[0.194,0.383],[0.179,0.418],[0.158,0.416],[0.113,0.38],[-0.26,0.38],[-0.279,0.39],[-0.312,0.448],[-0.322,0.454],[-0.331,0.454],[-0.357,0.428],[-0.371,0.442],[-0.395,0.451],[-0.557,0.451],[-0.587,0.436],[-0.594,0.418],[-0.593,0.39],[-0.61,0.38],[-0.626,0.393],[-0.626,0.437],[-0.651,0.454],[-0.664,0.446],[-0.705,0.383],[-0.87,0.381],[-0.931,0.375],[-1.031,0.354],[-1.057,0.339],[-1.094,0.276]],"features":{"base":[[[-0.472,-0.212],[0.483,-0.212],[0.5,-0.204],[0.512,-0.193],[0.518,-0.179],[0.518,0.09],[0.515,0.111],[0.508,0.132],[0.495,0.151],[0.32,0.343],[0.303,0.358],[0.282,0.37],[0.261,0.379],[0.24,0.381],[0.113,0.381],[0.092,0.378],[0.073,0.369],[0.061,0.356],[0.05,0.332],[0.046,0.28],[0.046,0.237],[0.043,0.211],[0.034,0.195],[0.021,0.187],[0.003,0.184],[-0.404,0.184],[-0.43,0.176],[-0.451,0.161],[-0.467,0.145],[-0.477,0.127],[-0.493,0.1],[-0.511,0.069],[-0.517,0.048],[-0.517,-0.163],[-0.513,-0.185],[-0.503,-0.2],[-0.488,-0.209]]],"arm":[[[-1.112,0.069],[-1.111,0.111],[-1.109,0.153],[-1.106,0.195],[-1.102,0.237],[-1.097,0.269],[-1.089,0.295],[-1.077,0.32],[-1.06,0.339],[-1.039,0.352],[-1.01,0.362],[-0.973,0.37],[-0.931,0.377],[-0.889,0.381],[0.209,0.381],[0.257,0.371],[0.297,0.344],[0.324,0.304],[0.334,0.256],[0.324,0.209],[0.297,0.169],[0.257,0.141],[0.209,0.132],[0.166,0.139],[0.132,0.158],[0.108,0.184],[-0.404,0.184],[-0.435,0.174],[-0.525,0.069],[-0.546,0.045],[-0.562,0.031],[-0.578,0.022],[-0.593,0.018],[-1.058,0.018],[-1.079,0.023],[-1.097,0.035],[-1.108,0.05]]],"knob":[[[-0.593,0.451],[-0.359,0.451],[-0.359,0.062],[-0.593,0.062]]],"ridge_rear":[[[-0.712,0.381],[-0.655,0.452],[-0.644,0.452],[-0.627,0.431],[-0.624,0.381]]],"ridge_front":[[[-0.358,0.381],[-0.358,0.426],[-0.334,0.452],[-0.323,0.452],[-0.27,0.381]]],"tab":[[[0.119,0.381],[0.132,0.389],[0.154,0.415],[0.166,0.419],[0.179,0.419],[0.184,0.412],[0.187,0.385],[0.192,0.381]]],"pivot":[[[0.126,0.34],[0.293,0.34],[0.293,0.173],[0.126,0.173]]],"nut":[[[-0.351,0.137],[-0.049,0.137],[-0.049,-0.165],[-0.351,-0.165]]]},"scaleRefs":["magpul-mbus-pro-front.clamp_length","magpul-mbus-pro-front.clamp_depth","magpul-mbus-pro-front.length"],"inputs":{"magpul-mbus-pro-front.clamp_depth":0.212,"magpul-mbus-pro-front.clamp_length":1.035,"magpul-mbus-pro-front.length":1.63},"tolerance":0.004,"photo":"references/magpul-mbus-pro-front 3dc752d09e8f (US D705,890 S (Magpul, 'Folding front sight for a firearm'), FIG. 6 right side elevation, folded, 300 dpi)","method":"luminance < 128, inside [440, 1880, 2080, 2600], closing ×3, largest piece, holes filled, inset 2 px (half the outline's stroke); frame from the reviewed holes front, tip (947.9 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.004 in with the extremes kept: 47 points (IoU 0.996 with the full outline); checks: height 0.667 ± 0.003 in vs magpul-mbus-pro-front.folded_overall_height 0.666 ± 0.005 (provisional): agrees; width in y [-0.2, -0.03] 1.037 ± 0.003 in vs magpul-mbus-pro-front.clamp_length 1.035 ± 0.008 (provisional): agrees; y_max 0.454 ± 0.002; features through the same placement (base: the base alone: its right wall, the hinge ear and the front chamfer (the arm lifted off); arm: the arm folded: its nose, its top face, the hinge barrel about the pin (hidden by the ear: a round of the top face's height about the pin), its underside on the base's walls, the wings' lobes behind the base; knob: the elevation knob: its two ends along the arm, its top, and as far below the pin's axis as its top is above; ridge_rear: the ridge across the arm behind the knob's window; ridge_front: the ridge ahead of the knob's window; tab: the tab on the hinge barrel; pivot: the hinge pin's pocket: the box about its circle (79.5 px about (1741, 2122)); nut: the cross bolt's nut on the right wall: the box about its outer circle (143 px about (1353, 2378))) (tools/trace.py)","via":"harvest","note":"The sight folded, from the rifle's right: the hinge at the front, the arm lying to the rear over the base and 0.60 in past it. The knob and the two ridges beside it stand above the arm's face."},"end":{"plane":"zy","origin":"the photo's frame","offset":{},"points":[[-0.65,0.113],[-0.65,0.026],[-0.585,0.026],[-0.578,0.019],[-0.578,-0.053],[-0.585,-0.06],[-0.65,-0.059],[-0.647,-0.159],[-0.624,-0.191],[-0.603,-0.202],[-0.562,-0.202],[-0.54,-0.182],[-0.49,-0.183],[-0.458,-0.211],[-0.438,-0.2],[-0.367,-0.2],[-0.351,-0.187],[-0.349,-0.176],[-0.4,-0.123],[-0.394,-0.118],[0.415,-0.118],[0.421,-0.125],[0.356,-0.191],[0.361,-0.206],[0.38,-0.213],[0.451,-0.213],[0.504,-0.165],[0.568,-0.16],[0.596,-0.132],[0.598,-0.087],[0.594,0.101],[0.564,0.126],[0.508,0.13],[0.313,0.361],[0.296,0.368],[0.223,0.368],[0.167,0.409],[0.121,0.43],[0.067,0.447],[0.002,0.455],[-0.055,0.45],[-0.123,0.431],[-0.184,0.401],[-0.228,0.368],[-0.3,0.368],[-0.318,0.361],[-0.479,0.169],[-0.535,0.169],[-0.548,0.158],[-0.573,0.169],[-0.605,0.166],[-0.635,0.145]],"features":{"channel":[[[0.44,-0.234],[0.44,-0.087],[0.346,0],[-0.346,0],[-0.443,-0.087],[-0.443,-0.234]]],"body":[[[0.537,-0.212],[0.54,0.071],[0.522,0.133],[0.293,0.363],[-0.293,0.363],[-0.522,0.133],[-0.537,0.071],[-0.537,-0.212]]],"ears_gap":[[[0.211,0.377],[-0.211,0.377],[-0.211,0.27],[0.211,0.27]]],"head":[[[-0.545,0.179],[-0.649,0.179],[-0.649,-0.205],[-0.545,-0.205]]],"head_slot":[[[-0.579,0.023],[-0.653,0.023],[-0.653,-0.068],[-0.579,-0.068]]],"nut":[[[0.598,0.124],[0.537,0.124],[0.537,-0.176],[0.598,-0.176]]],"bolt":[[[0.44,0.086],[-0.443,0.086],[-0.443,-0.114],[0.44,-0.114]]],"lip_right":[[[0.44,-0.114],[0.432,-0.114],[0.355,-0.19],[0.366,-0.207],[0.44,-0.211]]],"lip_left":[[[-0.443,-0.114],[-0.434,-0.114],[-0.348,-0.177],[-0.344,-0.19],[-0.356,-0.197],[-0.443,-0.197]]]},"scaleRefs":["magpul-mbus-pro-front.clamp_depth","magpul-mbus-pro-front.folded_overall_height"],"inputs":{"magpul-mbus-pro-front.clamp_depth":0.212,"magpul-mbus-pro-front.folded_overall_height":0.666},"tolerance":0.004,"photo":"references/magpul-mbus-pro-front 5412c5a0484c (US D705,890 S (Magpul, 'Folding front sight for a firearm'), FIG. 3 front elevation, folded, 300 dpi)","method":"luminance < 128, inside [620, 740, 1910, 1470], closing ×3, largest piece, holes filled, inset 2 px (half the outline's stroke); frame from the reviewed holes bottom, top (948.9 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.004 in with the extremes kept: 52 points (IoU 0.993 with the full outline); checks: width 1.248 ± 0.004 in vs magpul-mbus-pro-front.width 1.248 ± 0.01 (provisional): agrees; y_max 0.455 ± 0.002; features through the same placement (channel: the saddle's channel over the rail: its roof, the two 45° corners, the walls (carried below the jaws); body: the base's own section from the front: its legs, the 45° shoulders, the hinge ears' top (the bolt's head and nut and the arm left off); ears_gap: the gap between the two hinge ears, where the arm's barrel sits; head: the cross bolt's head, edge on (rifle's left); head_slot: the head's screwdriver slot; nut: the nut's boss, edge on (rifle's right); bolt: the cross bolt where it crosses the channel: its bottom is the heavy line at row 1326 to 1330, its axis the head's and the nut's; lip_right: the fixed jaw's lip under the rail's right edge (seen through the saddle): its 45° face from the wall to its tip; lip_left: the clamp bar's lip under the rail's left edge) (tools/trace.py)","via":"harvest","note":"From the muzzle end, turned to the frame's handedness (z to the rifle's right): the bolt's head on the left, its nut on the right. The arc at the top is the knob and the ridges' crown."},"plan":{"plane":"xz","origin":"the photo's frame","offset":{},"points":[[-1.113,0.287],[-1.097,0.262],[-1.059,0.237],[-0.773,0.17],[-0.751,0.15],[-0.743,0.129],[-0.743,0.089],[-0.752,0.081],[-0.803,0.082],[-0.829,0.064],[-0.881,0.046],[-1.01,0.037],[-1.009,-0.023],[-0.894,-0.031],[-0.855,-0.04],[-0.799,-0.068],[-0.75,-0.067],[-0.743,-0.073],[-0.745,-0.119],[-0.752,-0.137],[-0.774,-0.155],[-1.07,-0.227],[-1.113,-0.267],[-1.105,-0.3],[-1.09,-0.325],[-1.029,-0.354],[-0.981,-0.366],[-0.743,-0.337],[-0.528,-0.345],[-0.519,-0.354],[-0.519,-0.439],[-0.512,-0.454],[-0.486,-0.472],[-0.398,-0.498],[-0.388,-0.507],[-0.378,-0.549],[-0.394,-0.585],[-0.38,-0.62],[-0.358,-0.645],[-0.322,-0.656],[-0.084,-0.656],[-0.044,-0.644],[-0.023,-0.62],[-0.011,-0.585],[-0.015,-0.56],[-0.024,-0.549],[-0.009,-0.529],[0.006,-0.526],[0.011,-0.517],[0.01,-0.408],[0.016,-0.401],[0.025,-0.413],[0.026,-0.526],[0.05,-0.539],[0.343,-0.537],[0.437,-0.513],[0.495,-0.49],[0.507,-0.48],[0.517,-0.455],[0.518,-0.373],[0.518,0.446],[0.516,0.478],[0.496,0.504],[0.402,0.539],[0.33,0.553],[-0.029,0.553],[-0.049,0.563],[-0.053,0.587],[-0.078,0.617],[-0.132,0.623],[-0.322,0.62],[-0.348,0.589],[-0.353,0.542],[-0.365,0.528],[-0.417,0.522],[-0.503,0.484],[-0.519,0.453],[-0.519,0.376],[-0.527,0.36],[-0.755,0.352],[-0.976,0.381],[-1.013,0.374],[-1.086,0.343],[-1.105,0.315]],"features":{"arm":[[[-1.112,-0.268],[-1.107,-0.296],[-1.095,-0.322],[-1.076,-0.335],[-1.031,-0.354],[-0.987,-0.365],[-0.942,-0.363],[-0.875,-0.352],[-0.786,-0.34],[-0.742,-0.337],[-0.653,-0.338],[-0.541,-0.344],[-0.43,-0.355],[-0.319,-0.369],[-0.207,-0.38],[-0.096,-0.387],[-0.007,-0.389],[0.01,-0.382],[0.029,-0.346],[0.044,-0.302],[0.051,-0.235],[0.057,-0.218],[0.305,-0.218],[0.344,-0.174],[0.344,0.174],[0.305,0.218],[0.057,0.218],[0.051,0.235],[0.044,0.302],[0.029,0.346],[0.01,0.382],[-0.007,0.389],[-0.096,0.387],[-0.207,0.38],[-0.319,0.369],[-0.43,0.355],[-0.541,0.344],[-0.653,0.338],[-0.742,0.337],[-0.786,0.34],[-0.875,0.352],[-0.942,0.363],[-0.987,0.365],[-1.031,0.354],[-1.076,0.335],[-1.095,0.322],[-1.107,0.296],[-1.112,0.268],[-1.098,0.246],[-1.053,0.22],[-0.987,0.204],[-0.875,0.176],[-0.809,0.159],[-0.775,0.148],[-0.758,0.129],[-0.747,0.101],[-0.744,0.068],[-0.744,-0.068],[-0.747,-0.101],[-0.758,-0.129],[-0.775,-0.148],[-0.809,-0.159],[-0.875,-0.176],[-0.987,-0.204],[-1.053,-0.22],[-1.098,-0.246]]],"window":[[[-0.625,-0.218],[-0.269,-0.218],[-0.269,0.218],[-0.625,0.218]]],"pocket":[[[-0.216,-0.224],[0.002,-0.224],[0.002,0.224],[-0.216,0.224]]],"post":[[[-1.011,-0.026],[-0.886,-0.026],[-0.803,-0.067],[-0.744,-0.067],[-0.744,0.068],[-0.803,0.068],[-0.886,0.03],[-1.011,0.03]]]},"scaleRefs":["magpul-mbus-pro-front.clamp_length","magpul-mbus-pro-front.length"],"inputs":{"magpul-mbus-pro-front.clamp_length":1.035,"magpul-mbus-pro-front.length":1.63},"tolerance":0.004,"photo":"references/magpul-mbus-pro-front e8f213fddc31 (US D705,890 S (Magpul, 'Folding front sight for a firearm'), FIG. 7 top plan, folded, 300 dpi)","method":"luminance < 128, inside [440, 1760, 2000, 3010], closing ×3, largest piece, holes filled, inset 2 px (half the outline's stroke); frame from the reviewed holes front, tip (898.2 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.004 in with the extremes kept: 84 points (IoU 0.995 with the full outline); checks: height 1.279 ± 0.004; features through the same placement (arm: the arm's planform: the two wings and the fork between them, the body, the barrel between the hinge ears (the lower half is the upper's mirror about the post's axis, row 2401); window: the knob's window through the arm; pocket: the pocket in the arm's face between the window and the hinge; post: the post in the fork: its blade, the cone under it, its foot) (tools/trace.py)","via":"harvest","note":"From above, the muzzle to the right of the sheet, turned to the frame (z to the rifle's right). Scaled by its own length: sheet 4 is drawn 5.2% smaller than the elevations along the sight and 3.0% across it, so its widths stand 2% over theirs; the end elevation limits the hull across."}},"gaps":[{"what":"The sight's true scale: Magpul's 1.63 in stowed length against 1.57 (Recoil, 2015) and a .835 in rail in the patent's clamp","need":"A photo of it on a rail straight from the side or from above (the slots give the scale), or a dimensioned drawing"},{"what":"Its width","need":"A maker's figure; it is read off the patent's front elevation (1.25 in across the cross bolt)"},{"what":"The deck under the arm and the clamp's separate bar","need":"The deck from a straight photo of it standing from the rear or above; the bar from the patent's FIG. 4 and FIG. 5, which are on file and not yet traced"},{"what":"The colour","need":"A match to a photo under the app's light; the placeholder black stands in"}]},"magpul-mbus-pro-rear":{"id":"magpul-mbus-pro-rear","name":"MBUS Pro Sight – Rear","manufacturer":"Magpul","sku":"MAG276","url":"https://magpul.com/mbus-pro-sight-rear.html","category":"backup_sight","description":"Magpul's MBUS Pro rear sight: an all-steel folding backup sight for a Picatinny rail, with tool-less windage and a small aperture on a plate that flips down to leave a large one. Black.","weight":"magpul-mbus-pro-rear.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":["{.clamp_length} / 2 - {.screw_behind_front}",0,0],"note":"On the rail's top at the clamp screw's axis: the screw crosses the channel and sits in the rail's slot, so it is what a slot holds. The sight frame's origin is the middle of the clamp (the base's two ends), 0.17 in behind it."},"optical_axis":{"origin":["{.clamp_length} / 2 - {.hinge_behind_front}","{.sight_line_above_rail}",0],"note":"The aperture's centre, the sight standing (Magpul: \"Aperture height over rail: 1.42 in.\"), over the hinge: the arm stands on it, its front face 0.15 in ahead and its rear face 0.17 in behind."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":"={.clamp_length} - {.screw_behind_front}","clamp_front":"={.screw_behind_front}","stowed_rear":"={.length} - {.screw_behind_front}"},"flips":false,"start":"rear","note":"The base's two ends about the clamp screw (0.58 in behind it, 0.24 ahead). Magpul: \"Mounts on any MIL-STD-1913 Picatinny/STANAG 4694 rail\"; its sheet: \"Position the sight so the Sight Arm folds down to the rear\", \"hand tighten the screw ... DO NOT OVER-TIGHTEN\" (no torque figure). Folded, the arm lies 1.28 in further back than the base, over the rail (Magpul: \"Stowed footprint covers 2.1” of rail\"): `stowed_rear` is that footprint behind the screw, and a new one starts where the rail has that much behind it (app/src/assembly/pick.ts)."},"sight_line":{"type":"optic.sight_line","role":"irons","params":{"magnification":"1x"},"flips":false,"note":"An iron sight: it doesn't magnify, and nothing is checked against it (data/interfaces.yaml). Magpul: \"Standard AR sight height when deployed\"."}},"folds":{"up":"up","folded":"folded","note":"It folds down to the rear (the installation sheet: \"Position the sight so the Sight Arm folds down to the rear\"; the patent's FIG. 5), the arm's front face up."},"materials":{"body":{"label":"Sight","finish":"nitride","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"nitride","color":"placeholder-black","sku":"MAG276-BLK","source":"https://magpul.com/mbus-pro-sight-rear.html"}},"default":"black","note":"Magpul: \"All-steel construction with a QPQ nitride finish\", and on the same page \"THE ALL-STEEL CONSTRUCTION IS FINISHED WITH A QPQ SALT BATH NITRIDE PROCESS\": drawn as black nitride. One colour (its page's Color has Black alone, MAG276_RET_BLK_ in its data, and prints \"NSN: MAG276-BLK 1005-01-628-5113\"). Piece by piece on Magpul's photos (gallery rear_01 at 2000 px, rear_02, rear_03): the base, the arm, the aperture plate and its flip tab, the windage knob and its screw, the clamp's cross bolt and its nut, the hinge pin and the detent's ball are one black, with nothing bright or brass among them; the springs under the arm are dark too. One slot. A nitride black isn't fitted to a photo (its brightness there is reflection): the colour is the placeholder black."}},"components":{},"geometry":{"components":{"up":"magpul-mbus-pro-rear.up.glb","folded":"magpul-mbus-pro-rear.folded.glb"},"approximations":["Built from Magpul's design patent for it (US D704,792 S: the right side and front elevations and the two plans, each scaled by the stowed length, 2.1 in), piece by piece: the base's section with its fixed jaw, the loose bar, the clamp screw with its slotted head and the boss it ends in, the windage screw with its cap and its ten-lobed knob, the two ears, the arm with its knuckle. The figures then put the small aperture at 0.071 in across (Magpul: 0.07), the jaws 0.87 in apart on a 0.835 in rail, and the sight's top on its centre line 0.370 in above the rail (Magpul: ~0.38, earlier ~0.37 \"at mid-point\"). The fixed jaw's inner face, on the right, and the loose bar's, on the left, are made the standard's head in section (MIL-STD-1913's, since 2026-10-12) from the rail's top down to the lower gauge line: the elevation's own are a hundredth or two off a rail's all the way down.","Standing is the folded sight with its arm turned a quarter turn about the hinge, square to the rail: the aperture's centre then stands 1.417 in above the rail's top against Magpul's 1.42 (and 1.41), and the arm's tip 1.63. How far the arm leans when it stands isn't measured.","Folded, the windage knob's top is 0.43 in above the rail and the ear beside it 0.40: both higher than the stowed height Magpul gives, which the patent matches on the sight's centre line.","Every recess is the same depth, 0.03 in (relief_depth: one oblique photo bounds the logo panel's between 0.01 and 0.07): the logo's panel and the aperture plate's window in the arm's front face, the pad and the four pockets between the ribs in its rear face, the pocket in the base's top. The pockets between the ribs are deeper on the sight.","The aperture is drawn with the small aperture up: a 0.07 in hole through a web 0.03 in thick under the window's floor, the 0.19 in aperture bored up to it from the arm's rear face. The plate that carries the small aperture, its hinge and its flip tab aren't separate pieces.","The base's left side is closed square under its flank where the loose bar covers it, and the bar is run into it; the knob's lobes are plain bars half a period wide; the standing arm's lower corners run 0.04 in into the right ear (on the sight they are relieved).","Placed by its clamp screw in a rail's slot; the screw's place is the patent's (0.237 in behind the base's front face by the side elevation, 0.247 by the plan), and its height the front elevation's, where its head stands (its axis 0.015 in under the rail's top; the side elevation draws its boss 0.014 in lower).","Not drawn: the screws' threads, the pad's serrations, the five windage marks and the pointer, the Magpul mark, the MBUS PRO lettering, the knob's R and arrow and its set screw, the detents, the aperture plate's pivot pin. Edges broken at 0.01 in."],"ledger":["magpul-mbus-pro-rear.length","magpul-mbus-pro-rear.width","magpul-mbus-pro-rear.height","magpul-mbus-pro-rear.height_up","magpul-mbus-pro-rear.sight_line_above_rail","magpul-mbus-pro-rear.clamp_length","magpul-mbus-pro-rear.clamp_below_rail","magpul-mbus-pro-rear.knob_face_z","magpul-mbus-pro-rear.hinge_above_rail","magpul-mbus-pro-rear.hinge_behind_front","magpul-mbus-pro-rear.screw_behind_front","magpul-mbus-pro-rear.relief_depth","magpul-mbus-pro-rear.small_aperture_d","magpul-mbus-pro-rear.large_aperture_d","magpul-mbus-pro-rear.knob_lobes"]},"profiles":{"side":{"plane":"xy","origin":"the base's front face at the clamp's lowest point (the jaws' bottom); offset to the clamp's middle on the rail's top","offset":{"x":"front_x","y":"clamp_bottom_y"},"points":[[-2.1,0.229],[-2.094,0.224],[-1.965,0.223],[-0.836,0.224],[-0.818,0.211],[-0.818,0.037],[-0.801,0.011],[-0.782,0.001],[-0.041,0],[-0.015,0.015],[-0.001,0.047],[0,0.268],[-0.006,0.298],[-0.018,0.321],[-0.211,0.514],[-0.238,0.531],[-0.279,0.544],[-0.456,0.544],[-0.477,0.565],[-0.492,0.569],[-0.501,0.562],[-0.533,0.584],[-0.549,0.601],[-0.55,0.619],[-0.569,0.628],[-0.61,0.638],[-0.631,0.621],[-0.679,0.621],[-0.696,0.637],[-0.705,0.638],[-0.758,0.62],[-0.769,0.594],[-0.783,0.58],[-0.792,0.577],[-0.804,0.587],[-0.826,0.587],[-0.859,0.548],[-1.726,0.552],[-1.833,0.541],[-2.007,0.514],[-2.041,0.5],[-2.072,0.465],[-2.093,0.326]],"features":{"knob":[[[-0.409,0.642],[-0.409,0.153],[-0.899,0.153],[-0.899,0.642]]],"knob_root":[[[-0.428,0.624],[-0.428,0.17],[-0.881,0.17],[-0.881,0.624]]],"knob_face":[[[-0.459,0.594],[-0.459,0.202],[-0.85,0.202],[-0.85,0.594]]],"knob_hub":[[[-0.588,0.465],[-0.588,0.332],[-0.721,0.332],[-0.721,0.465]]],"boss":[[[-0.07,0.349],[-0.07,0.013],[-0.405,0.013],[-0.405,0.349]]],"boss_bore":[[[-0.103,0.317],[-0.103,0.046],[-0.372,0.046],[-0.372,0.317]]],"screw_end":[[[-0.158,0.26],[-0.158,0.103],[-0.317,0.103],[-0.317,0.26]]],"base":[[[0.001,0.544],[0.001,-0.001],[-0.819,-0.001],[-0.819,0.544]]],"arm_pin":[[[-1.56,0.502],[-1.56,0.42],[-1.643,0.42],[-1.643,0.502]]]},"scaleRefs":["magpul-mbus-pro-rear.length"],"inputs":{"magpul-mbus-pro-rear.length":2.1},"tolerance":0.004,"photo":"references/magpul-mbus-pro-rear db3b0b65d493 (US D704,792 S (Magpul, 'Folding rear sight for a firearm'), FIG. 5 right side elevation, folded; the patent office's copy, page 6, 300 dpi)","method":"luminance < 128, inside [560, 760, 1200, 2700], 1 boxes excluded, closing ×8, holes filled, inset 2 px (half the outline's stroke); rotated -90.0° as declared; scale from magpul-mbus-pro-rear.length = 2.1 in (x-extent 1854 px → 882.9 px/in); origin at x max, y min of the outline; Douglas-Peucker at 0.004 in with the extremes kept: 43 points (IoU 0.997 with the full outline); features through the same placement (knob: the windage knob's lobes: a circle through their tips (centre u 795.5 v 1378.0, r 215.9 px), as its box; its centre is the hinge's axis; knob_root: the knob between its lobes: the outermost ink on rays from its centre reads 199 to 200 px in the gaps and 216 to 218 on the lobes, ten of each to the turn (three whole periods of 36 degrees on the clear arc, 143 to 248 degrees); knob_face: the knob's flat outer face: the ring inside its rim (r 172.7 px); knob_hub: the hub in the knob's face (r 58.6 px); boss: the round boss on the fixed jaw the clamp screw ends in: its outer ring (centre u 986.5 v 1010.0, r 148.3 px); boss_bore: the ring inside the boss (r 119.1 px); screw_end: the clamp screw's end in the boss (r 69.6 px); base: the base: its top line (u 666), front face (v 800), the jaws' bottom (u 1147) and their rear end (v 1523.5), stroke centres; arm_pin: the aperture plate's pivot pin, its end on the arm's side (r 36.4 px)) (tools/trace.py)","via":"harvest","note":"Folded, from the right: the windage knob in front of the hinge, the clamp screw's boss ahead of it."},"plan":{"plane":"xz","origin":"the base's front face at the windage knob's outer face (the rifle's right); offset to the clamp's middle on the rail's centre line","offset":{"x":"front_x","y":"knob_face_z"},"points":[[-2.1,-0.641],[-2.1,-0.84],[-2.087,-0.913],[-2.041,-0.983],[-2.016,-1.008],[-1.989,-1.023],[-1.955,-1.033],[-1.92,-1.033],[-1.701,-1.019],[-1.605,-1.019],[-1.259,-1.084],[-1.246,-1.095],[-1.237,-1.089],[-1.037,-1.13],[-0.865,-1.135],[-0.837,-1.119],[-0.831,-1.126],[-0.831,-1.194],[-0.803,-1.252],[-0.8,-1.294],[-0.782,-1.312],[-0.518,-1.314],[-0.469,-1.322],[-0.468,-1.271],[-0.448,-1.257],[-0.422,-1.291],[-0.442,-1.294],[-0.442,-1.33],[-0.426,-1.364],[-0.403,-1.388],[-0.375,-1.397],[-0.13,-1.397],[-0.103,-1.389],[-0.082,-1.368],[-0.057,-1.325],[-0.072,-1.294],[-0.083,-1.291],[-0.074,-1.281],[-0.073,-1.238],[-0.055,-1.22],[-0.015,-1.206],[-0.003,-1.193],[0,-1.171],[0,-0.296],[-0.004,-0.274],[-0.02,-0.258],[-0.085,-0.236],[-0.104,-0.217],[-0.107,-0.191],[-0.125,-0.171],[-0.131,-0.176],[-0.166,-0.176],[-0.184,-0.16],[-0.32,-0.16],[-0.339,-0.176],[-0.365,-0.176],[-0.37,-0.171],[-0.396,-0.187],[-0.414,-0.169],[-0.414,-0.041],[-0.454,0],[-0.856,0],[-0.866,-0.005],[-0.895,-0.036],[-0.898,-0.049],[-0.898,-0.235],[-0.892,-0.251],[-0.867,-0.274],[-0.87,-0.327],[-0.891,-0.347],[-1.001,-0.346],[-1.124,-0.369],[-1.134,-0.37],[-1.141,-0.363],[-1.167,-0.378],[-1.592,-0.461],[-1.723,-0.461],[-1.925,-0.448],[-1.973,-0.451],[-2.022,-0.478],[-2.075,-0.546],[-2.089,-0.575]],"features":{"arm":[[[-0.83,-1.104],[-0.841,-1.124],[-0.862,-1.134],[-0.979,-1.135],[-1.037,-1.131],[-1.179,-1.101],[-1.237,-1.089],[-1.527,-1.035],[-1.565,-1.024],[-1.605,-1.019],[-1.701,-1.019],[-1.92,-1.032],[-1.955,-1.032],[-1.981,-1.027],[-2.011,-1.013],[-2.039,-0.987],[-2.086,-0.914],[-2.101,-0.84],[-2.101,-0.641],[-2.086,-0.566],[-2.039,-0.494],[-2.011,-0.468],[-1.981,-0.454],[-1.955,-0.448],[-1.92,-0.448],[-1.701,-0.461],[-1.605,-0.461],[-1.565,-0.457],[-1.527,-0.446],[-1.237,-0.391],[-1.179,-0.379],[-1.037,-0.35],[-0.979,-0.345],[-0.862,-0.346],[-0.841,-0.356],[-0.83,-0.377]]],"knuckle":[[[-0.509,-0.923],[-0.509,-0.555],[-0.805,-0.555],[-0.805,-0.923]]],"index_rib":[[[-0.769,-0.897],[-0.769,-0.583],[-0.853,-0.583],[-0.853,-0.897]]],"shaft":[[[-0.571,-1.057],[-0.571,-0.422],[-0.746,-0.422],[-0.746,-1.057]]],"ear_right":[[[-0.444,-0.422],[-0.444,-0.271],[-0.871,-0.271],[-0.871,-0.422]]],"ear_left":[[[-0.495,-1.214],[-0.495,-1.057],[-0.819,-1.057],[-0.819,-1.214]]],"cap":[[[-0.512,-1.314],[-0.512,-1.214],[-0.8,-1.214],[-0.8,-1.314]]],"knob":[[[-0.412,-0.261],[-0.412,0.001],[-0.899,0.001],[-0.899,-0.261]]],"bolt_head":[[[-0.055,-1.398],[-0.055,-1.297],[-0.439,-1.297],[-0.439,-1.398]]],"clamp_bar":[[[-0.001,-1.297],[-0.001,-1.175],[-0.445,-1.175],[-0.445,-1.297]]],"body":[[[-0.001,-1.175],[-0.001,-0.176],[-0.822,-0.176],[-0.822,-1.175]]],"boss":[[[-0.125,-0.176],[-0.125,-0.158],[-0.37,-0.158],[-0.37,-0.176]]],"slot":[[[-0.495,-1.057],[-0.495,-0.422],[-0.827,-0.422],[-0.827,-1.057]]],"top_pocket":[[[-0.194,-0.983],[-0.194,-0.497],[-0.417,-0.497],[-0.417,-0.983]]],"ticks":[[[-0.41,-0.871],[-0.41,-0.858],[-0.483,-0.858],[-0.483,-0.871]],[[-0.41,-0.746],[-0.41,-0.734],[-0.483,-0.734],[-0.483,-0.746]],[[-0.41,-0.621],[-0.41,-0.609],[-0.483,-0.609],[-0.483,-0.621]],[[-0.442,-0.808],[-0.442,-0.795],[-0.481,-0.795],[-0.481,-0.808]],[[-0.442,-0.686],[-0.442,-0.672],[-0.481,-0.672],[-0.481,-0.686]]],"logo_panel":[[[-0.965,-0.964],[-0.923,-0.925],[-0.923,-0.555],[-0.965,-0.517],[-1.337,-0.588],[-1.375,-0.619],[-1.375,-0.862],[-1.337,-0.892]]],"window":[[[-1.441,-0.856],[-1.441,-0.624],[-1.687,-0.624],[-1.687,-0.608],[-2.064,-0.608],[-2.064,-0.873],[-1.687,-0.873],[-1.687,-0.856]]],"aperture":[[[-1.849,-0.775],[-1.849,-0.704],[-1.92,-0.704],[-1.92,-0.775]]],"aperture_sink":[[[-1.807,-0.818],[-1.807,-0.663],[-1.963,-0.663],[-1.963,-0.818]]]},"scaleRefs":["magpul-mbus-pro-rear.length"],"inputs":{"magpul-mbus-pro-rear.length":2.1},"tolerance":0.004,"photo":"references/magpul-mbus-pro-rear f9854fd2c2a8 (US D704,792 S (Magpul, 'Folding rear sight for a firearm'), FIG. 7 top plan, folded; the patent office's copy, page 7, 300 dpi)","method":"luminance < 128, inside [560, 720, 1940, 2720], 1 boxes excluded, closing ×14, holes filled, notches filled in [600, 825, 706, 1175] (disk closing, r 60 px), notches filled in [676, 1195, 915, 1530] (disk closing, r 120 px), inset 2 px (half the outline's stroke); rotated -90.0° as declared; scale from magpul-mbus-pro-rear.length = 2.1 in (x-extent 1919 px → 913.8 px/in); origin at x max, y max of the outline; Douglas-Peucker at 0.004 in with the extremes kept: 82 points (IoU 0.996 with the full outline); features through the same placement (arm: the arm's outline in plan, from its front edge behind the base to its tip: the mask's own contour behind the knob (v > 1600), mirrored about u 1209, the front corners (r about 40 px) by eye; knuckle: the arm's knuckle round the hinge, between the base's ears: its ends across (u 1042, 1378) and its front (v 1234), mirrored about the axis (v 1369); index_rib: the raised rib behind the hinge that carries the windage pointer; shaft: the windage screw where its thread shows between the knuckle and the ears: the thread's crests (v 1290, 1450) and the ears' inner faces (u 920, 1500); ear_right: the base's right ear, round about the hinge: its faces (u 1500, 1638) and its rear end (v 1563.5), mirrored about the axis; ear_left: the base's left ear: its faces (u 776, 920) and its rear end (v 1517), mirrored about the axis; cap: the windage screw's cap outside the left ear: its outer face (u 685) and its two ends (v 1236, 1500); knob: the windage knob: its inner and outer faces (u 1647, 1886) and its two ends (v 1145, 1590); bolt_head: the clamp screw's head: its outer face (u 608), the bar's face it bears on (u 700) and its two ends (v 819, 1170); clamp_bar: the clamp's loose bar on the left: from the front face (v 769) to its rear end (v 1175); body: the base in plan: its front face (v 769) and its rear face (v 1520); across, the fixed jaw's outer face (u 1725) and the wall the bar bears on (u 812); boss: the screw's boss proud of the fixed jaw's face (u 1725 to 1740.5); slot: the fork the knuckle sits in: between the ears' inner faces (u 920, 1500), from its front wall (v 1221) back; top_pocket: the shallow pocket in the base's top (its rear end is rounded); ticks: the five windage marks ahead of the hinge; logo_panel: the sunk panel on the arm's front face that carries the logo: its rim (the outer of its two lines); window: the window in the arm's head the aperture's plate lies in: its narrow part by the flip tab and its wide part round the aperture; aperture: the small aperture: the innermost ring (centre u 1209.2 v 2490.9, r 32.5 px); aperture_sink: the outermost ring round the aperture on the plate (r 71.0 px)) (tools/trace.py)","via":"harvest","note":"Folded, from above: the arm's front face up (the logo's panel, the aperture's plate), the knob to the right, the clamp screw's head to the left."},"bottom":{"plane":"xz","origin":"the base's front face at the windage knob's outer face; offset as the top plan","offset":{"x":"front_x","y":"knob_face_z"},"points":[[-2.1,-0.64],[-2.1,-0.84],[-2.091,-0.899],[-2.078,-0.93],[-2.024,-1.002],[-1.967,-1.032],[-1.864,-1.032],[-1.656,-1.018],[-1.591,-1.021],[-1.037,-1.132],[-0.867,-1.137],[-0.85,-1.132],[-0.817,-1.165],[-0.817,-1.216],[-0.797,-1.244],[-0.797,-1.278],[-0.804,-1.292],[-0.78,-1.316],[-0.529,-1.316],[-0.483,-1.271],[-0.469,-1.269],[-0.435,-1.301],[-0.443,-1.328],[-0.42,-1.372],[-0.392,-1.395],[-0.363,-1.4],[-0.137,-1.4],[-0.102,-1.391],[-0.078,-1.367],[-0.065,-1.33],[-0.07,-1.305],[-0.08,-1.293],[-0.072,-1.277],[-0.074,-1.253],[-0.037,-1.216],[-0.009,-1.206],[0,-1.185],[0,-0.293],[-0.007,-0.268],[-0.07,-0.242],[-0.103,-0.209],[-0.103,-0.199],[-0.116,-0.182],[-0.16,-0.177],[-0.176,-0.161],[-0.316,-0.16],[-0.337,-0.177],[-0.379,-0.18],[-0.412,-0.147],[-0.413,-0.041],[-0.444,-0.005],[-0.456,0],[-0.847,0],[-0.864,-0.007],[-0.889,-0.032],[-0.898,-0.051],[-0.897,-0.234],[-0.89,-0.252],[-0.866,-0.278],[-0.868,-0.316],[-0.901,-0.349],[-0.912,-0.343],[-0.919,-0.348],[-0.973,-0.348],[-0.981,-0.343],[-1.041,-0.352],[-1.403,-0.425],[-1.439,-0.421],[-1.457,-0.434],[-1.484,-0.441],[-1.616,-0.464],[-1.919,-0.449],[-1.954,-0.449],[-1.989,-0.459],[-2.019,-0.478],[-2.087,-0.549],[-2.079,-0.559],[-2.091,-0.586]],"features":{"aperture":[[[-1.92,-0.777],[-1.92,-0.706],[-1.848,-0.706],[-1.848,-0.777]]],"aperture_bore":[[[-1.976,-0.834],[-1.976,-0.65],[-1.792,-0.65],[-1.792,-0.834]]],"pad":[[[-2.061,-0.955],[-2.061,-0.527],[-1.687,-0.527],[-1.687,-0.955]]],"rib_pockets":[[[-1.599,-0.905],[-1.599,-0.578],[-1.302,-0.683],[-1.28,-0.706],[-1.28,-0.777],[-1.302,-0.8]],[[-1.181,-0.777],[-1.181,-0.706],[-1.132,-0.686],[-0.88,-0.632],[-0.828,-0.658],[-0.813,-0.672],[-0.813,-0.811],[-0.828,-0.825],[-0.88,-0.851],[-1.132,-0.797]],[[-1.462,-0.95],[-1.462,-0.931],[-1.251,-0.866],[-1.233,-0.866],[-0.923,-0.92],[-0.923,-1.053],[-0.941,-1.065]],[[-1.462,-0.533],[-1.462,-0.552],[-1.251,-0.617],[-1.233,-0.617],[-0.923,-0.563],[-0.923,-0.43],[-0.941,-0.418]]],"screw":[[[-0.351,-1.085],[-0.351,-0.392],[-0.15,-0.392],[-0.15,-1.085]]],"knuckle":[[[-0.754,-0.931],[-0.754,-0.563],[-0.497,-0.563],[-0.497,-0.931]]]},"scaleRefs":["magpul-mbus-pro-rear.length"],"inputs":{"magpul-mbus-pro-rear.length":2.1},"tolerance":0.004,"photo":"references/magpul-mbus-pro-rear 56c0a21a26c3 (US D704,792 S (Magpul, 'Folding rear sight for a firearm'), FIG. 8 bottom plan, folded; the patent office's copy, page 8, 300 dpi)","method":"luminance < 128, inside [580, 720, 1960, 2740], 1 boxes excluded, closing ×28, holes filled, notches filled in [618, 2296, 716, 2645] (disk closing, r 60 px), notches filled in [860, 1260, 1000, 1800] (disk closing, r 40 px), notches filled in [1410, 1260, 1610, 1800] (disk closing, r 40 px), inset 2 px (half the outline's stroke); rotated +90.0° as declared; scale from magpul-mbus-pro-rear.length = 2.1 in (x-extent 1941 px → 924.3 px/in); origin at x max, y max of the outline; Douglas-Peucker at 0.004 in with the extremes kept: 78 points (IoU 0.996 with the full outline); checks: height 1.400 ± 0.003 in vs magpul-mbus-pro-rear.width 1.397 ± 0.03 (provisional): agrees; features through the same placement (aperture: the small aperture from behind: the innermost ring (centre u 1233.1 v 960.0, r 32.8 px); aperture_bore: the outermost ring round it on the arm's rear face (r 84.8 px): the large aperture's mouth; pad: the serrated pad round the aperture on the arm's rear face: its sides (u 1036, 1430.5), its lower edge (v 1142) and its upper edge (v 797, by eye: its corners are cut); rib_pockets: the four pockets between the X of ribs on the arm's rear face: the upper and the lower from the panels the strokes close (flood-filled, then squared by eye), the two at the sides by eye, the right one the left's mirror about u 1233; screw: the clamp screw's shank across the rail's channel: its two edges (v 2377, 2563) between the jaws (u 916, 1556); knuckle: the knuckle from below, between the ears (u 1058, 1398), and the fork's front wall (v 2241.5)) (tools/trace.py)","via":"harvest","note":"Folded, from below: the arm's rear face (which faces the eye when it stands) and the clamp's underside. The closing that bridges its dotted outline (28 px) fills the slit between the arm and the base and inside corners by 0.03 in: its features, not its outline, are what is read."},"front":{"plane":"zy","origin":"the windage knob's outer face at the clamp's lowest point; offset to the rail's centre line on its top","offset":{"x":"knob_face_z","y":"clamp_bottom_y"},"points":[[-1.397,0.057],[-1.366,0.021],[-1.344,0.01],[-1.303,0.011],[-1.28,0.028],[-1.27,0.023],[-1.211,0.023],[-1.193,0.004],[-1.182,0.002],[-1.169,0.015],[-1.105,0.014],[-1.08,0.029],[-1.082,0.042],[-1.125,0.084],[-1.116,0.093],[-0.411,0.092],[-0.39,0.119],[-0.368,0.098],[-0.349,0.123],[-0.321,0.087],[-0.371,0.033],[-0.37,0.008],[-0.363,0],[-0.29,0.002],[-0.239,0.046],[-0.194,0.047],[-0.178,0.062],[-0.177,0.107],[-0.159,0.124],[-0.159,0.15],[-0.15,0.159],[-0.046,0.161],[-0.011,0.183],[0,0.206],[-0.003,0.604],[-0.034,0.631],[-0.052,0.636],[-0.217,0.635],[-0.236,0.642],[-0.275,0.61],[-0.347,0.612],[-0.36,0.607],[-0.392,0.565],[-0.416,0.561],[-0.438,0.541],[-0.584,0.544],[-0.607,0.579],[-0.619,0.582],[-0.724,0.582],[-0.738,0.567],[-0.749,0.582],[-0.862,0.582],[-0.892,0.544],[-0.906,0.541],[-1.036,0.541],[-1.057,0.561],[-1.066,0.562],[-1.189,0.561],[-1.212,0.548],[-1.29,0.548],[-1.309,0.528],[-1.309,0.387],[-1.334,0.384],[-1.366,0.366],[-1.389,0.332],[-1.392,0.235],[-1.379,0.212],[-1.376,0.185],[-1.392,0.151],[-1.392,0.075]],"features":{"rail":[[[-0.299,0.213],[-1.164,0.213],[-1.164,0.092],[-0.299,0.092]]],"body":[[[-0.421,0.544],[-1.057,0.544],[-1.202,0.386],[-1.202,0.213],[-0.398,0.213],[-0.299,0.125],[-0.366,0.045],[-0.368,0.01],[-0.36,0.003],[-0.279,0.003],[-0.253,0.044],[-0.197,0.047],[-0.178,0.066],[-0.176,0.318],[-0.188,0.336],[-0.221,0.342],[-0.27,0.392]]],"clamp_bar":[[[-1.202,0.38],[-1.284,0.38],[-1.292,0.371],[-1.292,0.032],[-1.284,0.023],[-1.195,0.023],[-1.182,0.015],[-1.097,0.015],[-1.08,0.032],[-1.164,0.125],[-1.164,0.195],[-1.13,0.229],[-1.202,0.229]]],"knob":[[[0.001,0.638],[-0.26,0.638],[-0.26,0.161],[0.001,0.161]]],"bolt_head":[[[-1.292,0.391],[-1.398,0.391],[-1.398,0.006],[-1.292,0.006]]],"head_slot":[[[-1.323,0.234],[-1.398,0.234],[-1.398,0.152],[-1.323,0.152]]],"ear_right":[[[-0.27,0.612],[-0.365,0.612],[-0.365,0.187],[-0.27,0.187]]],"ear_left":[[[-1.056,0.562],[-1.208,0.562],[-1.208,0.237],[-1.056,0.237]]],"cap":[[[-1.208,0.549],[-1.309,0.549],[-1.309,0.25],[-1.208,0.25]]],"index_rib":[[[-0.595,0.583],[-0.886,0.583],[-0.886,0.544],[-0.595,0.544]]],"screw_end":[[[-0.158,0.267],[-0.176,0.267],[-0.176,0.121],[-0.158,0.121]]]},"scaleRefs":["magpul-mbus-pro-rear.width"],"inputs":{"magpul-mbus-pro-rear.width":1.397},"tolerance":0.004,"photo":"references/magpul-mbus-pro-rear 5159aa124947 (US D704,792 S (Magpul, 'Folding rear sight for a firearm'), FIG. 3 front elevation, folded; the patent office's copy, page 5, 300 dpi)","method":"luminance < 128, inside [600, 820, 2000, 1478], closing ×6, holes filled, notches filled in [1838, 1106, 1942, 1464] (disk closing, r 60 px), notches filled in [650, 864, 902, 906] (disk closing, r 25 px), inset 2 px (half the outline's stroke); scale from magpul-mbus-pro-rear.width = 1.397 in (x-extent 1288 px → 922.0 px/in); origin at x max, y min of the outline; Douglas-Peucker at 0.004 in with the extremes kept: 70 points (IoU 0.993 with the full outline); features through the same placement (rail: the rail's channel: its roof (v 1265, the lower of the two lines: the upper is the front edge's break), the two jaws' apexes (u 924, 1722) and the clamp screw's lowest line (v 1377); body: the base's section: top (v 960), flanks, the fixed jaw's outer face (u 811) and its hook (bottom v 1459), the channel's roof; clamp_bar: the loose bar's section: its outer face (u 1840), top (v 1111), hook (bottom v 1448) and the face that bears on the rail; closed inside the body; knob: the windage knob: its faces (u 648, 888) and its top and bottom (v 873, 1313); bolt_head: the clamp screw's head: from the bar's face (u 1840) to its outer face (u 1937), top and bottom (v 1101, 1456); head_slot: the slot in the screw's head (v 1246 to 1321, in to u 1868); ear_right: the base's right ear beside the knob: its outer face (u 897) and its top (v 897); ear_left: the left ear: its top (v 943) and outer face (u 1762); cap: the windage screw's cap: its top (v 955) and outer face (u 1855); index_rib: the rib that carries the windage pointer, the folded sight's highest point on its centre line: its top (v 924) on the body's top (v 960); screw_end: what stands proud of the fixed jaw's outer face (u 811) at the screw's end (u 794)) (tools/trace.py)","via":"harvest","note":"Folded, from the muzzle end, flipped: the clamp's two jaws below, the knob to the right, the clamp screw's head to the left."}},"gaps":[{"what":"Its width is the patent's, not a published figure (1.397 in over the windage knob and the clamp screw's head)","need":"A maker's figure, or a straight end view of the sight with a scale in its plane. AR15Discounts' shop field (2.1 × 1.4 × 0.38 in, unlabelled) may be the same width."},{"what":"Its standing height (1.63 in) and the arm's lean when it stands come from the patent's folded figures turned up, not from a view of it standing","need":"Magpul's photos of it standing from the side (a7d9a987a0d9) and from behind (acc7c896d80c) traced: the aperture's published height scales the second."},{"what":"No recess's depth is sourced (one figure, 0.03 ± 0.02 in, stands for all)","need":"A section, or two views of the arm's rear face from known angles."},{"what":"The colour is a placeholder black","need":"Two large photos sampled and matched under the app's light (docs/pipeline/ONBOARDING.md, stage 7); a nitrided steel's look is mostly reflection."},{"what":"Which end of the rail it goes on is from its name and its page's \"Position Rear\": the installation sheet says only which way round","need":"A maker's sentence, or the app's own rule for a rear sight. Folded, the arm needs 1.28 in of rail (or of clear air over the charging handle) behind the base."}]},"magpul-mlok-aluminum-rail-section-3-slot":{"id":"magpul-mlok-aluminum-rail-section-3-slot","name":"M-LOK® Aluminum Rail, 3 Slots","manufacturer":"Magpul","sku":"MAG580","url":"https://magpul.com/m-lokaluminumrail-3slots.html","category":"rail_section","description":"A three-slot Picatinny rail section machined from aluminium and hard anodized black, for any M-LOK hand guard or forend: two screws and two cammed T-nuts hold it in one M-LOK slot, and its recoil lugs sit in the slot. Its ends are bevelled. Magpul: \"M-LOK Aluminum Rail Sections allow the attachment of various 1913 Picatinny spec rail-mounted accessories such as lights, vertical grips, etc.\"","weight":"magpul-mlok-aluminum-rail-section-3-slot.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"lug":{"origin":["{.lug_x}",0,0],"note":"The centre of the M-LOK slot its rear T-nut is in, on its mounting face: what an M-LOK position places. Its two T-nuts one in each half of it (the screws over the first and the third grooves, the M-LOK interval apart). Rail section frame: origin at its rear end on the mounting face, +x toward the muzzle, +y away from the face."},"top_rail":{"origin":["{.rail_slot0_x}","{.height}",0],"note":"The rearmost rail slot's centre on the rail's top: what a clamp's position places, a slot further forward for each index."}},"interfaces":{"mlok":{"type":"mlok","role":"accessory","anchor":"lug","params":{"lugs":"={.lugs}","reach_inside":"={.reach_inside}"},"flips":true,"note":"Two T-nuts on two screws the M-LOK interval apart (20 mm: two rail pitches, as the photo from above has the screws): both in one slot. Magpul's sheet: \"All hardware necessary for attachment directly to M-LOK Slots on either aluminum or polymer hand guards and forends is included.\" How far the nuts reach inside isn't published."},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}"},"flips":false,"note":"Three slots of MIL-STD-1913 rail (Magpul: \"1913 Picatinny spec\"): what clamps to a Picatinny rail is mounted here (D72: a mount that carries others)."}},"materials":{"body":{"label":"Rail section","finish":"anodized","recolorable":true,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized","color":"placeholder-black","sku":"MAG580-BLK","source":"https://magpul.com/m-lokaluminumrail-3slots.html"}},"default":"black","note":"\"Machined from milspec-anodized aluminum\" (Magpul's sheet, MAG580-MAG583, colour \"BLK\"); \"Manufactured from black coated aluminum\" (Midwest Gun Works). Black is the one colour Magpul sells any of its aluminium rail sections in (its page has the one variant, MAG580_RET_BLK_ in its data and MAG580-BLK in its text; every seller seen sells black). A black on sealed anodize isn't fitted to a photo: the finish is its look."},"screws":{"label":"Screws","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The two button-head screws down in their counterbores: black (Magpul's photo from above, and on a hand guard). Steel; their coating isn't stated. The T-nuts are under the hand guard's face and aren't drawn."}},"components":{},"geometry":{"model":"magpul-mlok-aluminum-rail-section-3-slot.glb","components":{},"approximations":["The head is MIL-STD-1913's in section (lib.rail_head from the ledger), its three slots cut at the standard's width and depth on the standard's pitch from the first's place in the photos from above and below; under the head its lower 45 degree faces carried on past the lower gauge line down to the base's width as Primary Arms' photos of the three- and nine-slot's undersides have it (0.60 in: neck_width), 0.228 in under the top, and upright from there to the base. Which way the faces between the head and the base really lean isn't read: no view on file looks along the rail.","Its height is the line's (0.24 in), read on the five-slot's oblique photo; this length's own oblique photo reads 0.21, within its ±.","The ends: the base's outline from above (an arch with a 45 degree corner either side), and the end bevel from the base up to the rail's top, 0.14 in in along the part, round the arch at one width.","The two counterbores at the photo's size, over the first and the last groove; their floors (where the screws' heads seat) 0.2 in below the top, assumed. The screws are drawn as plain button heads at the photo's width, their height assumed and their hex sockets not drawn; the through holes under them and the T-nuts aren't drawn.","The recoil lugs under the base (Magpul: \"Recoil / impact mitigation lugs\"; Midwest Gun Works: \"2 recoil/impact mitigation lugs\"): Primary Arms' photo of its underside shows them, a pair of crescents either side of each hole making a ring the M-LOK slot's width, and the square pocket between the holes with Magpul's lasered marks. How far the lugs stand below the base isn't shown: neither is drawn, the base is flat.","Edges broken at 0.006 in."],"ledger":["magpul-mlok-aluminum-rail-section-3-slot.length","magpul-mlok-aluminum-rail-section-3-slot.height","magpul-mlok-aluminum-rail-section-3-slot.width","magpul-mlok-aluminum-rail-section-3-slot.neck_width","magpul-mlok-aluminum-rail-section-3-slot.rail_slot0_x","magpul-mlok-aluminum-rail-section-3-slot.end_bevel_run","magpul-mlok-aluminum-rail-section-3-slot.counterbore_d","magpul-mlok-aluminum-rail-section-3-slot.lug_x"]},"profiles":{"plan":{"plane":"xz","origin":"The part frame by its two through holes (their white seen through each is bounded at the base): the base's rear end at x 0, +x toward the muzzle, z across, symmetric about its centre line","offset":{},"points":[[-0.002,0.032],[-0.002,-0.05],[0.008,-0.134],[0.02,-0.197],[0.042,-0.274],[0.058,-0.299],[0.084,-0.314],[0.174,-0.39],[0.265,-0.391],[0.294,-0.373],[0.466,-0.372],[0.478,-0.376],[0.489,-0.389],[0.502,-0.392],[0.659,-0.393],[0.693,-0.373],[0.859,-0.373],[0.877,-0.376],[0.896,-0.393],[0.971,-0.393],[1.063,-0.392],[1.082,-0.377],[1.095,-0.374],[1.268,-0.374],[1.295,-0.393],[1.379,-0.393],[1.395,-0.387],[1.49,-0.312],[1.516,-0.304],[1.526,-0.294],[1.549,-0.217],[1.565,-0.14],[1.577,0.006],[1.575,0.075],[1.565,0.157],[1.55,0.226],[1.528,0.296],[1.455,0.377],[1.383,0.444],[1.298,0.445],[1.275,0.422],[1.247,0.419],[1.092,0.421],[1.083,0.425],[1.072,0.442],[1.052,0.445],[0.897,0.444],[0.883,0.425],[0.873,0.421],[0.712,0.42],[0.691,0.422],[0.675,0.443],[0.666,0.445],[0.527,0.446],[0.497,0.442],[0.49,0.429],[0.48,0.422],[0.442,0.419],[0.299,0.421],[0.291,0.423],[0.279,0.442],[0.272,0.445],[0.193,0.445],[0.177,0.44],[0.05,0.299],[0.014,0.171]],"scaleRefs":["magpul-mlok-aluminum-rail-section-3-slot.rail_slot0_x","std.picatinny.slot_pitch"],"inputs":{"magpul-mlok-aluminum-rail-section-3-slot.rail_slot0_x":0.395,"std.picatinny.slot_pitch":0.394},"tolerance":0.003,"photo":"references/magpul-mlok-aluminum-rail-section-3-slot bcda799c1d3e (Primary Arms' MAG580 from above (MAG580_01.jpg), 2200 x 1467, on white, no screws)","method":"luminance < 200, largest piece, holes filled; frame from the reviewed holes slot0, slot2 (1218.7 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.003 in with the extremes kept: 66 points (IoU 0.996 with the full outline) (tools/trace.py)","via":"harvest","note":"The base's outline from above, at the scale of its holes in the base's plane: at each end an arch with a 45 degree corner either side. What the model takes from it is the ends; its sides are the standard's head."}},"gaps":[{"what":"Its height above the hand guard's face, and how wide it is under the head","need":"A view of this length from its end or its side: its height is the line's, read on the five-slot, and its own oblique photo reads it to ± 0.04 in"},{"what":"Its weight","need":"A page that weighs it, Magpul's or a seller's that isn't a shipping weight: worked out from the model's aluminium meanwhile (weight)"},{"what":"How far its recoil lugs stand below the base (Primary Arms' photo of its underside shows where they are) and how far the T-nuts reach inside the hand guard (reach_inside)","need":"A view of it from its end or its side, or Magpul's drawing of it"}]},"magpul-mlok-aluminum-rail-section-5-slot":{"id":"magpul-mlok-aluminum-rail-section-5-slot","name":"M-LOK® Aluminum Rail, 5 Slots","manufacturer":"Magpul","sku":"MAG581","url":"https://magpul.com/m-lokaluminumrail-5slots.html","category":"rail_section","description":"A five-slot Picatinny rail section machined from aluminium and hard anodized black, for any M-LOK hand guard or forend: two screws and two cammed T-nuts hold it in two M-LOK slots side by side, and its recoil lugs sit in the slots. Its ends are bevelled. Magpul: \"M-LOK Aluminum Rail Sections allow the attachment of various 1913 Picatinny spec rail-mounted accessories such as lights, vertical grips, etc.\"","weight":"magpul-mlok-aluminum-rail-section-5-slot.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"lug":{"origin":["{.lug_x}",0,0],"note":"The centre of the M-LOK slot its rear T-nut is in, on its mounting face: what an M-LOK position places. The rear T-nut in that slot's rear half, under the rear screw in the first groove's floor, and the front one a slot pitch on in the next slot's. Rail section frame: origin at its rear end on the mounting face, +x toward the muzzle, +y away from the face."},"top_rail":{"origin":["{.rail_slot0_x}","{.height}",0],"note":"The rearmost rail slot's centre on the rail's top: what a clamp's position places, a slot further forward for each index."}},"interfaces":{"mlok":{"type":"mlok","role":"accessory","anchor":"lug","params":{"lugs":"={.lugs}","reach_inside":"={.reach_inside}"},"flips":true,"note":"Two T-nuts on two screws one M-LOK slot pitch apart (40 mm: four rail pitches, as the photo from above has the screws): one nut in each of two slots. Magpul's sheet: \"All hardware necessary for attachment directly to M-LOK Slots on either aluminum or polymer hand guards and forends is included.\" How far the nuts reach inside isn't published."},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}"},"flips":false,"note":"Five slots of MIL-STD-1913 rail (Magpul: \"1913 Picatinny spec\"; Primary Arms: \"5 slots of M1913 Picatinny rail\"): what clamps to a Picatinny rail is mounted here (D72: a mount that carries others)."}},"materials":{"body":{"label":"Rail section","finish":"anodized","recolorable":true,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized","color":"placeholder-black","sku":"MAG581-BLK","source":"https://magpul.com/m-lokaluminumrail-5slots.html"}},"default":"black","note":"\"Machined from milspec-anodized aluminum\" (Magpul's sheet, MAG580-MAG583, colour \"BLK\"); \"durable, corrosion-resistant anodized black finish\" (Primary Arms). Black is the one colour Magpul sells any of its aluminium rail sections in (its page has the one variant, MAG581_RET_BLK_ in its data and MAG581-BLK in its text; every seller seen sells black). A black on sealed anodize isn't fitted to a photo: the finish is its look."},"screws":{"label":"Screws","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The two button-head screws down in their counterbores: black (Midwest Gun Works' photo of the hardware beside it, Primary Arms' from above). Steel; their coating isn't stated. The T-nuts are under the hand guard's face and aren't drawn."}},"components":{},"geometry":{"model":"magpul-mlok-aluminum-rail-section-5-slot.glb","components":{},"approximations":["The head is MIL-STD-1913's in section (lib.rail_head from the ledger), its five slots cut at the standard's width and depth on the standard's pitch from the first's place in the photo from above; under the head its lower 45 degree faces carried on past the lower gauge line down to the base's width as Primary Arms' photos of the three- and nine-slot's undersides have it (0.60 in: neck_width), 0.228 in under the top, and upright from there to the base. Which way the faces between the head and the base really lean isn't read: no view on file looks along the rail.","Its height (0.24 in) is read on one oblique photo through a camera fitted to its own teeth; with the body under the head 0.79 across it would read 0.21.","The ends: the base's outline from above (an arch with a 45 degree corner either side), and the end bevel from the base up to the rail's top, 0.12 in in along the part, round the arch at one width.","The two counterbores at the photo's size, over the first and the last groove; their floors (where the screws' heads seat) 0.2 in below the top, assumed. The screws are drawn as plain button heads at the photo's width, their height assumed and their hex sockets not drawn; the through holes under them and the T-nuts aren't drawn.","The recoil lugs under the base (Magpul: \"Recoil / impact mitigation lugs\"; Midwest Gun Works: \"2 recoil/impact mitigation lugs\") aren't drawn: no view on file shows its underside.","Edges broken at 0.006 in."],"ledger":["magpul-mlok-aluminum-rail-section-5-slot.length","magpul-mlok-aluminum-rail-section-5-slot.height","magpul-mlok-aluminum-rail-section-5-slot.width","magpul-mlok-aluminum-rail-section-5-slot.neck_width","magpul-mlok-aluminum-rail-section-5-slot.rail_slot0_x","magpul-mlok-aluminum-rail-section-5-slot.end_bevel_run","magpul-mlok-aluminum-rail-section-5-slot.counterbore_d","magpul-mlok-aluminum-rail-section-5-slot.lug_x"]},"profiles":{"plan":{"plane":"xz","origin":"The base's rear end at x 0 (the outline's rearmost point, on its centre line), +x toward the muzzle, z across the part; the part is symmetric about its centre line, and the photo's rows 505 to 949 put that line at row 727","offset":{},"points":[[0.022,0.061],[0.022,-0.041],[0.036,-0.158],[0.072,-0.28],[0.171,-0.383],[0.197,-0.403],[0.221,-0.411],[0.297,-0.411],[0.302,-0.397],[0.314,-0.389],[0.495,-0.389],[0.506,-0.395],[0.509,-0.408],[0.516,-0.413],[0.688,-0.413],[0.693,-0.399],[0.707,-0.389],[0.885,-0.389],[0.899,-0.397],[0.905,-0.413],[1.078,-0.413],[1.084,-0.408],[1.084,-0.399],[1.1,-0.389],[1.274,-0.389],[1.292,-0.401],[1.297,-0.413],[1.473,-0.413],[1.475,-0.399],[1.488,-0.39],[1.575,-0.389],[1.671,-0.39],[1.688,-0.413],[1.864,-0.413],[1.869,-0.397],[1.879,-0.39],[2.062,-0.39],[2.081,-0.413],[2.168,-0.413],[2.194,-0.394],[2.234,-0.354],[2.303,-0.276],[2.319,-0.226],[2.34,-0.137],[2.351,-0.048],[2.353,0.035],[2.342,0.154],[2.327,0.224],[2.304,0.297],[2.205,0.39],[2.174,0.409],[2.083,0.409],[2.064,0.39],[1.884,0.39],[1.871,0.401],[1.871,0.408],[1.866,0.411],[1.692,0.411],[1.682,0.396],[1.669,0.39],[1.495,0.39],[1.482,0.396],[1.475,0.411],[1.298,0.411],[1.284,0.392],[1.098,0.392],[1.09,0.397],[1.083,0.411],[0.957,0.413],[0.905,0.411],[0.901,0.401],[0.889,0.392],[0.709,0.392],[0.697,0.399],[0.688,0.413],[0.514,0.413],[0.503,0.396],[0.492,0.392],[0.353,0.392],[0.312,0.394],[0.295,0.413],[0.204,0.413],[0.173,0.392],[0.07,0.299],[0.044,0.211],[0.029,0.134]],"scaleRefs":["magpul-mlok-aluminum-rail-section-5-slot.rail_slot0_x","std.picatinny.slot_pitch"],"inputs":{"magpul-mlok-aluminum-rail-section-5-slot.rail_slot0_x":0.403,"std.picatinny.slot_pitch":0.394},"tolerance":0.003,"photo":"references/magpul-mlok-aluminum-rail-section-5-slot 9f1857805a7d (Primary Arms' MAG581 from above, 2200 x 1467, on white)","method":"luminance < 200, largest piece, holes filled; frame from the reviewed holes slot0, slot4 (539.2 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.003 in with the extremes kept: 86 points (IoU 0.998 with the full outline) (tools/trace.py)","via":"harvest","note":"The base's outline from above: the long sides (the teeth's widest; the grooves 0.02 in inside it each side), and at each end a 45 degree corner either side of an arch. What the model takes from it is the ends; its sides are the standard's head."}},"gaps":[{"what":"Its height above the hand guard's face, and how wide it is under the head","need":"A view of it from its end, or a straight side view, with a scale: the one oblique photo reads 0.24 in with the body as narrow as the standard's lower gauge line, 0.21 if 0.79 across"},{"what":"Its weight","need":"A page that weighs it, Magpul's or a seller's that isn't a shipping weight: worked out from the model's aluminium meanwhile (weight)"},{"what":"Its underside: the recoil lugs (how many, their size and where) and how far the T-nuts reach inside the hand guard (reach_inside)","need":"A view of its underside, or Magpul's drawing of it"}]},"magpul-mlok-aluminum-rail-section-7-slot":{"id":"magpul-mlok-aluminum-rail-section-7-slot","name":"M-LOK® Aluminum Rail, 7 Slots","manufacturer":"Magpul","sku":"MAG582","url":"https://magpul.com/m-lokaluminumrail-7slots.html","category":"rail_section","description":"A seven-slot Picatinny rail section machined from aluminium and hard anodized black, for any M-LOK hand guard or forend: two screws and two cammed T-nuts hold it in two M-LOK slots side by side, and its recoil lugs sit in the slots. Its ends are bevelled. Magpul: \"M-LOK Aluminum Rail Sections allow the attachment of various 1913 Picatinny spec rail-mounted accessories such as lights, vertical grips, etc.\"","weight":"magpul-mlok-aluminum-rail-section-7-slot.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"lug":{"origin":["{.lug_x}",0,0],"note":"The centre of the M-LOK slot its rear T-nut is in, on its mounting face: what an M-LOK position places. The rear T-nut in that slot's rear half, under the rear screw in the first groove's floor, and the front one 60 mm on in the next slot's front half. Rail section frame: origin at its rear end on the mounting face, +x toward the muzzle, +y away from the face."},"top_rail":{"origin":["{.rail_slot0_x}","{.height}",0],"note":"The rearmost rail slot's centre on the rail's top: what a clamp's position places, a slot further forward for each index."}},"interfaces":{"mlok":{"type":"mlok","role":"accessory","anchor":"lug","params":{"lugs":"={.lugs}","reach_inside":"={.reach_inside}"},"flips":true,"note":"Two T-nuts on two screws six rail pitches apart (60 mm, one and a half M-LOK pitches): in the rear half of one slot and the front half of the next. Magpul's sheet: \"All hardware necessary for attachment directly to M-LOK Slots on either aluminum or polymer hand guards and forends is included.\" How far the nuts reach inside isn't published."},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}"},"flips":false,"note":"Seven slots of MIL-STD-1913 rail (Magpul: \"1913 Picatinny spec\"): what clamps to a Picatinny rail is mounted here (D72: a mount that carries others)."}},"materials":{"body":{"label":"Rail section","finish":"anodized","recolorable":true,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized","color":"placeholder-black","sku":"MAG582-BLK","source":"https://magpul.com/m-lokaluminumrail-7slots.html"}},"default":"black","note":"\"Machined from milspec-anodized aluminum\" (Magpul's sheet, MAG580-MAG583, colour \"BLK\"); \"M-LOK aluminum rail section for compatible hand guards and forends\" (KYGunCo). Black is the one colour Magpul sells any of its aluminium rail sections in (its page has the one variant, MAG582_RET_BLK_ in its data and MAG582-BLK in its text; every seller seen sells black, KYGunCo as MAG582-BLK). A black on sealed anodize isn't fitted to a photo: the finish is its look."},"screws":{"label":"Screws","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The two button-head screws down in their counterbores: black (Magpul's photos of it on a hand guard). Steel; their coating isn't stated. The T-nuts are under the hand guard's face and aren't drawn."}},"components":{},"geometry":{"model":"magpul-mlok-aluminum-rail-section-7-slot.glb","components":{},"approximations":["The head is MIL-STD-1913's in section (lib.rail_head from the ledger), its seven slots cut at the standard's width and depth on the standard's pitch from the first's place on its photo from above; under the head its lower 45 degree faces carried on past the lower gauge line down to the base's width as Primary Arms' photos of the three- and nine-slot's undersides have it (0.60 in: neck_width), 0.228 in under the top, and upright from there to the base. Which way the faces between the head and the base really lean isn't read: no view on file looks along the rail.","Its height is the line's (0.24 in), read on the five-slot's oblique photo; this length's own oblique photo reads 0.26, within its ±.","The ends: the base's outline from above (an arch with a 45 degree corner either side), its four quarters averaged into one symmetric end, each placed by the ledger's length, and the end bevel from the base up to the rail's top as the line's three- and five-slot lengths have it (0.13 in in along the part), round the arch at one width.","The two counterbores at its photo's size, over the first and the last grooves; their floors (where the screws' heads seat) 0.2 in below the top, assumed. The screws are drawn as plain button heads at the line's width (the three- and five-slot's), their height assumed and their hex sockets not drawn; the through holes under them and the T-nuts aren't drawn.","The recoil lugs under the base (Magpul: \"Recoil / impact mitigation lugs\"; Midwest Gun Works, of the three- and five-slot: \"2 recoil/impact mitigation lugs\") aren't drawn: no view on file shows its underside.","Edges broken at 0.006 in."],"ledger":["magpul-mlok-aluminum-rail-section-7-slot.length","magpul-mlok-aluminum-rail-section-7-slot.height","magpul-mlok-aluminum-rail-section-7-slot.width","magpul-mlok-aluminum-rail-section-7-slot.neck_width","magpul-mlok-aluminum-rail-section-7-slot.rail_slot0_x","magpul-mlok-aluminum-rail-section-7-slot.end_bevel_run","magpul-mlok-aluminum-rail-section-7-slot.counterbore_d","magpul-mlok-aluminum-rail-section-7-slot.front_block","magpul-mlok-aluminum-rail-section-7-slot.lug_x"]},"profiles":{"plan":{"plane":"xz","origin":"The part frame by its two through holes (their white seen through each is bounded at the base): the base's rear end at x 0, +x toward the muzzle, z across, symmetric about its centre line","offset":{},"points":[[-0.001,-0.033],[0.011,-0.154],[0.03,-0.236],[0.05,-0.294],[0.093,-0.349],[0.167,-0.428],[0.18,-0.438],[0.201,-0.445],[0.275,-0.443],[0.297,-0.417],[0.482,-0.418],[0.492,-0.423],[0.499,-0.442],[0.597,-0.444],[0.674,-0.442],[0.684,-0.424],[0.696,-0.416],[0.8,-0.414],[0.88,-0.417],[0.901,-0.443],[1.061,-0.443],[1.074,-0.441],[1.082,-0.425],[1.093,-0.415],[1.277,-0.416],[1.289,-0.426],[1.296,-0.442],[1.467,-0.442],[1.475,-0.439],[1.479,-0.424],[1.487,-0.416],[1.499,-0.414],[1.672,-0.415],[1.686,-0.425],[1.692,-0.441],[1.705,-0.443],[1.869,-0.441],[1.878,-0.421],[1.888,-0.415],[2.072,-0.416],[2.086,-0.428],[2.086,-0.437],[2.093,-0.442],[2.262,-0.443],[2.272,-0.437],[2.274,-0.424],[2.283,-0.417],[2.32,-0.415],[2.469,-0.417],[2.493,-0.443],[2.659,-0.444],[2.671,-0.436],[2.671,-0.425],[2.677,-0.42],[2.709,-0.416],[2.869,-0.418],[2.888,-0.442],[2.974,-0.443],[3.038,-0.383],[3.112,-0.295],[3.132,-0.232],[3.151,-0.144],[3.163,-0.04],[3.163,0.037],[3.148,0.165],[3.118,0.275],[3.1,0.3],[3.091,0.302],[3.046,0.348],[2.988,0.393],[2.897,0.394],[2.875,0.374],[2.83,0.372],[2.685,0.375],[2.675,0.39],[2.666,0.394],[2.508,0.395],[2.493,0.393],[2.486,0.381],[2.474,0.373],[2.292,0.374],[2.282,0.378],[2.271,0.393],[2.217,0.393],[2.096,0.394],[2.074,0.374],[1.888,0.375],[1.867,0.394],[1.705,0.395],[1.694,0.393],[1.677,0.373],[1.491,0.374],[1.481,0.379],[1.474,0.393],[1.297,0.394],[1.279,0.375],[1.096,0.373],[1.085,0.377],[1.074,0.393],[1.035,0.395],[0.897,0.393],[0.886,0.378],[0.878,0.374],[0.748,0.372],[0.694,0.374],[0.681,0.381],[0.673,0.394],[0.504,0.394],[0.496,0.392],[0.486,0.378],[0.476,0.373],[0.295,0.373],[0.284,0.378],[0.269,0.393],[0.18,0.393],[0.117,0.346],[0.072,0.303],[0.059,0.298],[0.047,0.282],[0.027,0.222],[0.008,0.127],[-0.001,0.028]],"scaleRefs":["magpul-mlok-aluminum-rail-section-7-slot.rail_slot0_x","std.picatinny.slot_pitch"],"inputs":{"magpul-mlok-aluminum-rail-section-7-slot.rail_slot0_x":0.398,"std.picatinny.slot_pitch":0.394},"tolerance":0.003,"photo":"references/magpul-mlok-aluminum-rail-section-7-slot c475d60ec064 (Primary Arms' MAG582 from above (MAG582_00.jpg), 2200 x 1466, on white, no screws)","method":"luminance < 200, largest piece, holes filled; frame from the reviewed holes slot0, slot6 (463.0 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.003 in with the extremes kept: 122 points (IoU 0.998 with the full outline) (tools/trace.py)","via":"harvest","note":"The base's outline from above, at the scale of its holes in the base's plane: at each end an arch with a 45 degree corner either side. What the model takes from it is the ends."}},"gaps":[{"what":"Its height above the hand guard's face, and how wide it is under the head","need":"A view of this length from its end or its side, at an angle a camera can be fitted to: its height is the line's, read on the five-slot"},{"what":"Its end bevel's run: the line's, as the three- and five-slot's views from above read it","need":"A view from above lit so that the bevel's top edge shows"},{"what":"Its weight","need":"A page that weighs it, Magpul's or a seller's that isn't a shipping weight: worked out from the model's aluminium meanwhile (weight)"},{"what":"Its underside: the recoil lugs (how many, their size and where) and how far the T-nuts reach inside the hand guard (reach_inside)","need":"A view of its underside, or Magpul's drawing of it"}]},"magpul-mlok-aluminum-rail-section-9-slot":{"id":"magpul-mlok-aluminum-rail-section-9-slot","name":"M-LOK® Aluminum Rail, 9 Slots","manufacturer":"Magpul","sku":"MAG583","url":"https://magpul.com/m-lokaluminumrail-9slots.html","category":"rail_section","description":"A nine-slot Picatinny rail section machined from aluminium and hard anodized black, for any M-LOK hand guard or forend: three screws and three cammed T-nuts hold it in three M-LOK slots side by side, and its recoil lugs sit in the slots. Its ends are bevelled. Magpul: \"M-LOK Aluminum Rail Sections allow the attachment of various 1913 Picatinny spec rail-mounted accessories such as lights, vertical grips, etc.\"","weight":"magpul-mlok-aluminum-rail-section-9-slot.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"lug":{"origin":["{.lug_x}",0,0],"note":"The centre of the M-LOK slot its rear T-nut is in, on its mounting face: what an M-LOK position places. The rear T-nut in that slot's rear half, under the rear screw in the first groove's floor, and the next two a slot pitch apart in the next slots'. Rail section frame: origin at its rear end on the mounting face, +x toward the muzzle, +y away from the face."},"top_rail":{"origin":["{.rail_slot0_x}","{.height}",0],"note":"The rearmost rail slot's centre on the rail's top: what a clamp's position places, a slot further forward for each index."}},"interfaces":{"mlok":{"type":"mlok","role":"accessory","anchor":"lug","params":{"lugs":"={.lugs}","reach_inside":"={.reach_inside}"},"flips":true,"note":"Three T-nuts on three screws one M-LOK slot pitch apart (40 mm: four rail pitches, the holes over the first, fifth and ninth grooves): one nut in each of three slots. Magpul's sheet: \"All hardware necessary for attachment directly to M-LOK Slots on either aluminum or polymer hand guards and forends is included.\" How far the nuts reach inside isn't published."},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}"},"flips":false,"note":"Nine slots of MIL-STD-1913 rail (Magpul: \"1913 Picatinny spec\"): what clamps to a Picatinny rail is mounted here (D72: a mount that carries others)."}},"materials":{"body":{"label":"Rail section","finish":"anodized","recolorable":true,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized","color":"placeholder-black","sku":"MAG583","source":"https://magpul.com/m-lokaluminumrail-9slots.html"}},"default":"black","note":"\"Machined from milspec-anodized aluminum\" (Magpul's sheet, MAG580-MAG583, colour \"BLK\"); \"Manufactured from black coated aluminum\" (Midwest Gun Works). Black is the one colour Magpul sells any of its aluminium rail sections in (its page has the one variant, MAG583_RET_BLK_ in its data; every seller seen sells black, Midwest Gun Works as MAG583). A black on sealed anodize isn't fitted to a photo: the finish is its look."},"screws":{"label":"Screws","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The three button-head screws down in their counterbores: black (Magpul's photos of it on a hand guard; Midwest Gun Works' of its hardware). Steel; their coating isn't stated. The T-nuts are under the hand guard's face and aren't drawn."}},"components":{},"geometry":{"model":"magpul-mlok-aluminum-rail-section-9-slot.glb","components":{},"approximations":["The head is MIL-STD-1913's in section (lib.rail_head from the ledger), its nine slots cut at the standard's width and depth on the standard's pitch from the first's place on its photo from above; under the head its lower 45 degree faces carried on past the lower gauge line down to the base's width as Primary Arms' photos of the three- and nine-slot's undersides have it (0.60 in: neck_width), 0.228 in under the top, and upright from there to the base. Which way the faces between the head and the base really lean isn't read: no view on file looks along the rail.","Its height is the line's (0.24 in), read on the five-slot's oblique photo; this length's own two oblique photos read 0.20 and 0.27 in, each within its ±.","The ends: the base's outline from above (an arch with a 45 degree corner either side), its four quarters averaged into one symmetric end, each placed by the ledger's length, and the end bevel from the base up to the rail's top as the line's three- and five-slot lengths have it (0.13 in in along the part), round the arch at one width.","The three counterbores at its photo's size, over the first, fifth and ninth grooves; their floors (where the screws' heads seat) 0.2 in below the top, assumed. The screws are drawn as plain button heads at the line's width (the three- and five-slot's), their height assumed and their hex sockets not drawn; the through holes under them and the T-nuts aren't drawn.","The recoil lugs under the base (Magpul: \"Recoil / impact mitigation lugs\"; Midwest Gun Works: \"3 recoil/impact mitigation lugs\") aren't drawn: no view on file shows its underside.","Edges broken at 0.006 in."],"ledger":["magpul-mlok-aluminum-rail-section-9-slot.length","magpul-mlok-aluminum-rail-section-9-slot.height","magpul-mlok-aluminum-rail-section-9-slot.width","magpul-mlok-aluminum-rail-section-9-slot.neck_width","magpul-mlok-aluminum-rail-section-9-slot.rail_slot0_x","magpul-mlok-aluminum-rail-section-9-slot.end_bevel_run","magpul-mlok-aluminum-rail-section-9-slot.counterbore_d","magpul-mlok-aluminum-rail-section-9-slot.front_block","magpul-mlok-aluminum-rail-section-9-slot.lug_x"]},"profiles":{"plan":{"plane":"xz","origin":"The part frame by its first and last through holes (their white seen through each is bounded at the base): the base's rear end at x 0, +x toward the muzzle, z across, symmetric about its centre line","offset":{},"points":[[-0.005,0.024],[-0.003,-0.071],[0.003,-0.126],[0.018,-0.201],[0.04,-0.278],[0.144,-0.384],[0.171,-0.402],[0.256,-0.402],[0.278,-0.382],[0.464,-0.382],[0.479,-0.402],[0.499,-0.402],[0.655,-0.402],[0.677,-0.382],[0.859,-0.382],[0.874,-0.402],[0.884,-0.404],[1.048,-0.404],[1.068,-0.384],[1.076,-0.382],[1.248,-0.382],[1.259,-0.384],[1.268,-0.399],[1.277,-0.404],[1.447,-0.404],[1.467,-0.384],[1.488,-0.382],[1.656,-0.384],[1.67,-0.404],[1.848,-0.404],[1.866,-0.384],[2.053,-0.384],[2.071,-0.404],[2.099,-0.406],[2.233,-0.406],[2.247,-0.404],[2.268,-0.384],[2.45,-0.383],[2.461,-0.391],[2.468,-0.404],[2.484,-0.406],[2.636,-0.406],[2.648,-0.404],[2.658,-0.388],[2.669,-0.383],[2.847,-0.383],[2.857,-0.387],[2.871,-0.406],[3.041,-0.406],[3.062,-0.385],[3.072,-0.383],[3.244,-0.383],[3.258,-0.389],[3.263,-0.4],[3.272,-0.405],[3.441,-0.405],[3.449,-0.403],[3.463,-0.385],[3.584,-0.383],[3.651,-0.385],[3.674,-0.405],[3.767,-0.403],[3.897,-0.285],[3.932,-0.157],[3.946,-0.021],[3.944,0.074],[3.936,0.139],[3.917,0.226],[3.895,0.297],[3.764,0.433],[3.746,0.437],[3.673,0.437],[3.647,0.413],[3.463,0.413],[3.444,0.435],[3.436,0.437],[3.345,0.437],[3.274,0.437],[3.248,0.413],[3.169,0.413],[3.065,0.413],[3.054,0.42],[3.047,0.435],[3.039,0.437],[2.875,0.437],[2.864,0.43],[2.855,0.415],[2.794,0.413],[2.668,0.413],[2.642,0.437],[2.478,0.437],[2.47,0.435],[2.463,0.422],[2.45,0.413],[2.399,0.411],[2.269,0.413],[2.258,0.42],[2.249,0.435],[2.241,0.437],[2.081,0.437],[2.068,0.43],[2.059,0.415],[2.038,0.413],[1.872,0.413],[1.857,0.424],[1.852,0.435],[1.844,0.437],[1.724,0.437],[1.674,0.435],[1.667,0.42],[1.655,0.412],[1.475,0.412],[1.462,0.422],[1.455,0.435],[1.443,0.437],[1.287,0.437],[1.277,0.435],[1.269,0.419],[1.258,0.412],[1.167,0.412],[1.078,0.412],[1.067,0.419],[1.058,0.435],[1.048,0.437],[0.894,0.437],[0.881,0.435],[0.863,0.412],[0.805,0.41],[0.681,0.412],[0.67,0.421],[0.665,0.432],[0.649,0.436],[0.486,0.434],[0.47,0.412],[0.436,0.41],[0.286,0.412],[0.262,0.434],[0.176,0.434],[0.094,0.352],[0.046,0.291],[0.009,0.156]],"scaleRefs":["magpul-mlok-aluminum-rail-section-9-slot.rail_slot0_x","std.picatinny.slot_pitch"],"inputs":{"magpul-mlok-aluminum-rail-section-9-slot.rail_slot0_x":0.395,"std.picatinny.slot_pitch":0.394},"tolerance":0.003,"photo":"references/magpul-mlok-aluminum-rail-section-9-slot a2581c8858ef (Primary Arms' MAG583 from above (MAG583_01.jpg), 2200 x 1467, on white, no screws)","method":"luminance < 200, largest piece, holes filled; frame from the reviewed holes slot0, slot8 (493.6 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.003 in with the extremes kept: 141 points (IoU 0.998 with the full outline) (tools/trace.py)","via":"harvest","note":"The base's outline from above, at the scale of its holes in the base's plane: at each end an arch with a 45 degree corner either side. What the model takes from it is the ends."}},"gaps":[{"what":"Its height above the hand guard's face, and how wide it is under the head","need":"A view of this length from its end or its side, at an angle a camera can be fitted to: its height is the line's, read on the five-slot"},{"what":"Its end bevel's run: the line's, as the three- and five-slot's views from above read it","need":"A view from above lit so that the bevel's top edge shows"},{"what":"Its weight","need":"A page that weighs it, Magpul's or a seller's that isn't a shipping weight: worked out from the model's aluminium meanwhile (weight)"},{"what":"Its underside: the recoil lugs (how many, their size and where) and how far the T-nuts reach inside the hand guard (reach_inside)","need":"A view of its underside, or Magpul's drawing of it"}]},"magpul-mlok-hand-stop-moe-adapter":{"id":"magpul-mlok-hand-stop-moe-adapter","name":"M-LOK Hand Stop MOE Adapter","manufacturer":"Magpul","url":"https://magpul.com/m-lok-handstop-kit.html","category":"adapter_plate","description":"The adapter plate of Magpul's M-LOK Hand Stop Kit (MAG608), sold only in that kit: for \"Magpul polymer M-LOK hand guards or aluminum hand guards with wider, flatter profiles\". The kit's hand stop and index panel bolt through it into the hand guard's slots, one at each end, with its moulded rail cover between them; it can be snapped shorter at two marked lines. Black, FDE, ODG, Stealth Gray.","weight":"magpul-mlok-hand-stop-moe-adapter.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"lug":{"origin":["{.position_x}",0,0],"note":"The centre of the rearmost slot it covers, on its mounting face: what an M-LOK position places (a plate at slot n lies over n and the two slots ahead of it). The middle of its rear pair of screw holes, which stand one M-LOK interval apart either side of it: a hand stop's two T-nuts go through them into that slot's two halves. Adapter plate frame: origin at the plate's rear end on the mounting face (the end sections' underside, which a T-nut draws down onto the hand guard), +x forward along the handguard, +y out of the face (away from the handguard: the solver turns it to the face it is on)."},"plate":{"origin":["{.position_x}","{.height}",0],"note":"The centre of its rear place on the flat an accessory's band bears on (the land, `height` above the mounting face): where what it carries is put, the front place one position_pitch ahead. An accessory's `lug` anchor is the middle of its nuts on its band, so placed here its two screws stand over the plate's two holes and its ears hang either side of the land."}},"interfaces":{"mlok":{"type":"mlok","role":"accessory","anchor":"lug","params":{"lugs":"={.lugs}","reach_inside":"={.reach_inside}","in_slot":true},"flips":false,"note":"`in_slot`: its places are over the handguard's slots, so it sits at the slots themselves and never between two. `lugs` is the slots it covers: three, a place over the first and the third and its moulded cover over the one between (Magpul's sheet, scenario 2, step 2). What of it stands in a slot (the seats round each screw hole) isn't measured."},"carries":{"type":"mlok","role":"slots","anchor":"plate","params":{"pitch":"={.position_pitch}","slots":"={.positions}","reach_inside":"={.carried_reach_inside}"},"flips":false,"only":["magpul-mlok-hand-stop","magpul-mlok-index-panel"],"note":"What it carries is mounted here: the kit's hand stop or its index panel, at either place (\"Attach the M-LOK Hand Stop and Index Panel to the M-LOK Hand Stop MOE Adapter\", Magpul's sheet). Each place is a recess the size of an M-LOK slot (31.3 x 7.1 mm for the standard's 32 x 7) with two screw holes the M-LOK interval apart; the two places are two slot pitches apart. The room under an accessory isn't published."}},"materials":{"body":{"label":"Adapter plate","finish":"polymer","recolorable":true,"color":"magpul-black","sheen":"matte","options":{"black":{"label":"Black","finish":"polymer","color":"magpul-black","sheen":"matte","source":"https://magpul.com/m-lok-handstop-kit.html"},"fde":{"label":"FDE","finish":"polymer","color":"magpul-fde","sheen":"matte","source":"https://magpul.com/m-lok-handstop-kit.html"},"odg":{"label":"ODG","finish":"polymer","color":"magpul-odg","sheen":"matte","source":"https://magpul.com/m-lok-handstop-kit.html"},"sgy":{"label":"Stealth Gray","finish":"polymer","color":"magpul-stealth-gray","sheen":"matte","source":"https://magpul.com/m-lok-handstop-kit.html"}},"default":"black","note":"Magpul's polymer, in the four colours the kit is sold in (the page's swatches: Black, Flat Dark Earth, Olive Drab Green, Stealth Gray), as matched on the MOE SL: the plate comes in its kit's colour. It has no number of its own; its mould mark is EN: 516-0110 (Primary Arms' and Wing Tactical's photos). The kit isn't sold in Modified Coyote Brown (its page, read 2026-10-06 on the harvested copy: four swatches). One moulding and nothing else: the plate, its moulded cover and its lugs are the kit's colour in Magpul's gallery in each of the four and in Wing Tactical's photos of the FDE and the ODG kit, and it has no hardware of its own (the hand stop's and the index panel's screws pass through it)."}},"components":{},"geometry":{"model":"magpul-mlok-hand-stop-moe-adapter.glb","components":{},"approximations":["Built from ledger figures alone, every one of them read from photographs (no drawing with a scale, no published size): the plan from one photo from above, scaled by the plate's own screw holes as the M-LOK interval and two slot pitches; the heights through cameras fitted to two oblique photos, which agree on the plate's thickness within 0.007 in.","Each end section is a flat (the land, 0.656 in wide, 0.103 above the mounting face) with one straight bevel down either side to a thin edge and end faces that lean 0.023 in: flat faces between the read edges. The recess at each place is cut to its read length, width and depth with an M-LOK slot's corner radius (std.mlok.slot_corner_r: the recess is a slot's shape, and its corners read about that), its walls upright; the two holes go straight through its floor.","The moulded cover's section is four read heights joined by one smooth curve: its crown (flush with the index panel's and the hand stop's on Magpul's drawing), over the land's edge, over the plate's edge, and its own edge at the mounting face's level. Its corners are rounded in plan as the photo from above has them, and each end face is one flat leaning back 0.05 in from the land's level to the crown (read once from each end, on the drawing's crown height); how its top rounds into its ends isn't read. Its TSP texture is the app's finish, not geometry.","The two snap-off scores are cut as wide as they read and to half the land's height: their depth isn't read. The notch in each end is cut through the whole height, as Magpul's image shows it.","The mounting side is drawn flat. On the part the seats round each screw hole stand off it into the hand guard's slot, a groove runs along either edge of each end section, and under the cover it is a waffle of ribs whose rim stands a little below the end sections' underside (cover_underside_drop: three sources show it, none measures it). The lettering (PATENT, MAGPUL, IP.MAGPUL.COM, EN: 516-0110) and the mould's marks aren't drawn. Edges broken at 0.006 in.","How the kit's pieces sit on it is inferred from their own figures, not seen in section: the land is narrower than the band between a hand stop's ears (0.656 against 0.698 in) and as thick, within its ±, as that band is deep (0.103 against 0.116), so the band bears on the land with the ears hanging either side of it, their tips at the hand guard's face. Magpul's drawing of the kit on the plate has the panel's ears' tips level with the plate's underside. By the figures as they stand the tips are 0.013 in past it."],"ledger":["magpul-mlok-hand-stop-moe-adapter.length","magpul-mlok-hand-stop-moe-adapter.height","magpul-mlok-hand-stop-moe-adapter.width","magpul-mlok-hand-stop-moe-adapter.end_width","magpul-mlok-hand-stop-moe-adapter.land_width","magpul-mlok-hand-stop-moe-adapter.edge_height","magpul-mlok-hand-stop-moe-adapter.end_inset","magpul-mlok-hand-stop-moe-adapter.position_pitch","magpul-mlok-hand-stop-moe-adapter.position_x","magpul-mlok-hand-stop-moe-adapter.score_x","magpul-mlok-hand-stop-moe-adapter.score_width","magpul-mlok-hand-stop-moe-adapter.cover_height","magpul-mlok-hand-stop-moe-adapter.cover_shoulder_height","magpul-mlok-hand-stop-moe-adapter.cover_edge_height","magpul-mlok-hand-stop-moe-adapter.cover_corner_radius","magpul-mlok-hand-stop-moe-adapter.cover_end_lean","magpul-mlok-hand-stop-moe-adapter.recess_length","magpul-mlok-hand-stop-moe-adapter.recess_width","magpul-mlok-hand-stop-moe-adapter.recess_depth","magpul-mlok-hand-stop-moe-adapter.screw_hole_diameter","magpul-mlok-hand-stop-moe-adapter.end_notch_depth","magpul-mlok-hand-stop-moe-adapter.end_notch_width"]},"profiles":{},"gaps":[{"what":"A size for it from its maker: every figure is read from photographs, the widths from one","need":"A Magpul drawing or figure for the kit's pieces, a seller's measurement, or a view of it from its end with a scale"},{"what":"How far the moulded cover's ribbed underside stands below the end sections' mounting face, and so whether the plate's ends or its middle meet a flat face first (cover_underside_drop)","need":"A side view of the plate alone square to its length, or of its mounting side beside a scale"},{"what":"How far the seats round its screw holes stand into the hand guard's slot (reach_inside), and the room under an accessory (carried_reach_inside)","need":"A section, or a photo of its mounting side from its edge"},{"what":"How deep the snap-off scores are, and how the cover's top rounds into its ends","need":"A close side view of the plate alone"}]},"magpul-mlok-hand-stop":{"id":"magpul-mlok-hand-stop","name":"M-LOK Hand Stop","manufacturer":"Magpul","url":"https://magpul.com/m-lok-handstop-kit.html","category":"hand_stop","description":"The hand stop of Magpul's M-LOK Hand Stop Kit (MAG608), which is the only way it is sold: with an index panel, a Type 2 rail cover and an adapter plate for Magpul polymer hand guards. Reinforced polymer with the TSP texture; Black, FDE, ODG, Stealth Gray. On a machined metal or narrow M-LOK hand guard it bolts straight into a slot with its two T-nuts (Magpul's instruction sheet 072-0098-A, scenario 1): it needs no plate under it.","weight":"magpul-mlok-hand-stop.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"lug":{"origin":["{.lug_x} + {std.mlok.interval} / 2","{.mounting_band_depth}",0],"note":"The middle of its two T-nuts on the band between its ears, which is the face that bears on a handguard (mounting_band_depth below the ears' tips, where the part's frame has y 0: until 2026-10-05 it was seated on the tips and touched nothing). The nuts are the M-LOK interval apart (the patent's plan view has them 0.793 in): what an M-LOK position places. Since 2026-10-05 the middle of the two, not the rear one: a slot's position is its centre, and two nuts the M-LOK interval apart go one in each half of it (the rear nut on the centre put the front one 4 mm past the slot's end, over the web). The part frame's origin is the part's rear end on that face."}},"interfaces":{"mlok":{"type":"mlok","role":"accessory","anchor":"lug","params":{"lugs":"={.lugs}","reach_inside":"={.reach_inside}"},"flips":true,"note":"One slot: its base plate is one slot pitch long (40 mm) and its two nuts 20 mm apart (the patent's plan view); a configurator site's two slots is kept as a conflict. How far the nuts reach inside isn't published."}},"materials":{"body":{"label":"Hand stop","finish":"polymer","recolorable":true,"color":"magpul-black","sheen":"matte","options":{"black":{"label":"Black","finish":"polymer","color":"magpul-black","sheen":"matte","source":"https://magpul.com/m-lok-handstop-kit.html"},"fde":{"label":"FDE","finish":"polymer","color":"magpul-fde","sheen":"matte","source":"https://magpul.com/m-lok-handstop-kit.html"},"odg":{"label":"ODG","finish":"polymer","color":"magpul-odg","sheen":"matte","source":"https://magpul.com/m-lok-handstop-kit.html"},"sgy":{"label":"Stealth Gray","finish":"polymer","color":"magpul-stealth-gray","sheen":"matte","source":"https://magpul.com/m-lok-handstop-kit.html"}},"default":"black","note":"Magpul's reinforced polymer with the TSP texture, in Magpul's colours as matched on the MOE SL. It has no number of its own: the kit's are MAG608-BLK, -FDE, -ODG and -GRY as retailers print them (Magpul's page prints MAG608 and the swatches; its data has MAG608_RET_BLK_, _FDE_, _ODG_ and _GRY_), one colour to a kit. The kit isn't sold in Modified Coyote Brown, as the Type 2 covers now are (the kit's page, read 2026-10-06 on the harvested copy: four swatches). All of the hand stop is the one moulding in the kit's colour (Magpul's gallery in each of the four; Wing Tactical's photos of the FDE and the ODG kit apart)."},"screws":{"label":"Screw","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The screw in the plate ahead of the hook: black on the FDE kit as on the black one (Magpul's gallery picture of the FDE kit put together, mag608_fde_2: both screws that show are a blue-black against the tan), and dark grey with the T-nuts in Wing Tactical's photo of the ODG kit's hardware (six screws, three nuts, a yellow patch of thread locker on each thread). A steel screw, its coating not stated by anyone: drawn as dark steel in the placeholder black, the same in every colour of the kit. The hook's own screw is down inside its hollow and the T-nuts are inside the hand guard: neither is drawn."}},"components":{},"geometry":{"model":"magpul-mlok-hand-stop.glb","components":{},"approximations":["A visual hull of Magpul's design patent's side and front elevations and its bottom plan (US D755,333 S, FIG. 6, FIG. 3 and FIG. 8: the plate's four corners chamfered, 2026-10-03), scaled to the base plate's length as the user's gallery image has it (the handguard's rail teeth the scale): it tapers from the mounting face (1.05 in, the ears at its edges) to about half that at its lip. The tracing closes the ribs' grooves on the hollow (0.02 in).","It bears on the band between its ears (FIG. 3: 0.116 in below their tips, 0.70 in across), and its ears run down either side of the handguard's face: every M-LOK face on file is narrower than the band. (Until 2026-10-05 the ears' tips, the outermost line on the face side, were taken as the face it mounts on; a flat wider than the tips' 1.05 in would be the one host they bear on.) The dashed lug and crescents FIG. 7 draws there are the T-nut's hardware, its environment.","The finger ribs across its hollow, the screw bosses, the lug and the mounting side's thin steps aren't drawn. Edges broken at 0.02 in.","The plate's screw is drawn (2026-10-06): its recess where FIG. 8 has it, one M-LOK interval ahead of the hook's screw, at the drawing's two circles and as deep as a 45 degree countersink between them makes it (0.02 in: no view gives the depth); its head a low dome on the recess's floor, as wide as Magpul's picture of the FDE kit has it and its crown 0.033 in out of the plate, as the user's side view has it. The head's profile between those two readings and its six-lobe socket aren't sourced; the socket isn't drawn. The hook's own screw, inside its hollow, isn't drawn: the hull has no hollow."],"ledger":["magpul-mlok-hand-stop.length","magpul-mlok-hand-stop.height","magpul-mlok-hand-stop.width","magpul-mlok-hand-stop.lug_x","magpul-mlok-hand-stop.screw_recess_diameter","magpul-mlok-hand-stop.screw_recess_floor_diameter","magpul-mlok-hand-stop.screw_head_diameter","magpul-mlok-hand-stop.screw_head_proud","std.mlok.interval"]},"profiles":{"side":{"plane":"xy","origin":"the plate's rear end, which is the hook's, on the mounting face (the figure's outermost line on that side)","offset":{},"points":[[0,0.275],[0.003,0.048],[0.06,0.011],[0.097,0],[1.458,0],[1.557,0.035],[1.569,0.045],[1.575,0.078],[1.569,0.247],[1.391,0.25],[1.37,0.239],[1.154,0.232],[1.031,0.249],[0.886,0.325],[0.823,0.389],[0.769,0.478],[0.753,0.475],[0.73,0.498],[0.745,0.526],[0.725,0.575],[0.712,0.572],[0.688,0.595],[0.707,0.625],[0.692,0.673],[0.659,0.696],[0.678,0.728],[0.668,0.778],[0.639,0.801],[0.661,0.83],[0.656,0.884],[0.628,0.91],[0.655,0.937],[0.655,0.99],[0.63,1.017],[0.659,1.042],[0.666,1.096],[0.644,1.122],[0.674,1.145],[0.686,1.197],[0.668,1.228],[0.689,1.249],[0.702,1.248],[0.729,1.311],[0.79,1.401],[0.775,1.49],[0.746,1.505],[0.48,1.468],[0.387,1.427],[0.346,1.385],[0.265,1.273],[0.062,0.954],[0.022,0.879],[0.004,0.8]],"scaleRefs":["magpul-mlok-hand-stop.length"],"inputs":{"magpul-mlok-hand-stop.length":1.575},"tolerance":0.006,"photo":"references/magpul-mlok-hand-stop f25270f81003 (US D755,333 S (Magpul, 'Hand stop for a firearm'), FIG. 6 right side elevation, 300 dpi)","method":"luminance < 128, inside [520, 889, 2083, 2521], 1 boxes excluded, closing ×18, holes filled, notches filled in [760, 1380, 920, 1640] (disk closing, r 45 px), inset 2 px (half the outline's stroke); rotated -90.0° as declared; scale from magpul-mlok-hand-stop.length = 1.575 in (x-extent 1549 px → 983.5 px/in); origin at x min, y min of the outline; Douglas-Peucker at 0.006 in with the extremes kept: 53 points (IoU 0.993 with the full outline) (tools/trace.py)","via":"harvest","note":"The mounting side is a stack of thin steps in the drawing (0.02 and 0.04 in): the outline takes the outermost. The ribs' ends show on the hollow side; the TSP texture and the screw bosses don't."},"front":{"plane":"zy","origin":"the mounting face, centred","offset":{},"points":[[-0.527,0.022],[-0.523,0.005],[-0.508,0.002],[-0.348,0.116],[0.35,0.116],[0.52,0],[0.527,0.045],[0.284,1.426],[0.263,1.453],[0.232,1.465],[0.107,1.498],[-0.005,1.504],[-0.141,1.49],[-0.262,1.456],[-0.284,1.429]],"scaleRefs":["magpul-mlok-hand-stop.height","magpul-mlok-hand-stop.width"],"inputs":{"magpul-mlok-hand-stop.height":1.505,"magpul-mlok-hand-stop.width":1.053},"tolerance":0.006,"photo":"references/magpul-mlok-hand-stop 644316cf46e4 (US D755,333 S (Magpul, 'Hand stop for a firearm'), FIG. 3 front elevation, 300 dpi)","method":"luminance < 128, inside [560, 740, 1965, 2700], 1 boxes excluded, closing ×18, holes filled, inset 2 px (half the outline's stroke); rotated +180.0° as declared; scale from magpul-mlok-hand-stop.height = 1.505 in (y-extent 1938 px → 1287.7 px/in) and magpul-mlok-hand-stop.width = 1.053 in (x-extent 1358 px → 1289.6 px/in), which agree within 0.2%; mean 1288.7 px/in; origin at x center, y min of the outline; Douglas-Peucker at 0.006 in with the extremes kept: 15 points (IoU 0.991 with the full outline) (tools/trace.py)","via":"harvest","note":"Symmetric. The finger ribs across its face are inside the outline; the taper is the outline's."},"plan":{"plane":"xz","origin":"the plate's rear end (the hook's), centred","offset":{},"points":[[0,-0.396],[0.012,-0.47],[0.061,-0.519],[0.069,-0.512],[0.107,-0.526],[1.459,-0.526],[1.548,-0.488],[1.576,-0.449],[1.576,0.452],[1.56,0.477],[1.489,0.518],[1.455,0.526],[0.11,0.526],[0.077,0.517],[0.034,0.487],[0.009,0.463],[0.003,0.445]],"scaleRefs":["magpul-mlok-hand-stop.length","magpul-mlok-hand-stop.width"],"inputs":{"magpul-mlok-hand-stop.length":1.575,"magpul-mlok-hand-stop.width":1.053},"tolerance":0.006,"photo":"references/magpul-mlok-hand-stop 322d06fd979a (US D755,333 S (Magpul, 'Hand stop for a firearm'), FIG. 8 bottom plan, 300 dpi)","method":"luminance < 128, inside [540, 650, 1960, 2745], closing ×18, holes filled, inset 2 px (half the outline's stroke); rotated +90.0° as declared; scale from magpul-mlok-hand-stop.length = 1.575 in (x-extent 2034 px → 1291.4 px/in) and magpul-mlok-hand-stop.width = 1.053 in (y-extent 1359 px → 1290.6 px/in), which agree within 0.1%; mean 1291.0 px/in; origin at x min, y center of the outline; Douglas-Peucker at 0.006 in with the extremes kept: 17 points (IoU 0.997 with the full outline) (tools/trace.py)","via":"harvest","note":"Symmetric. The screw holes' dashed circles (broken lines: environment) aren't drawn."}},"gaps":[{"what":"How far the T-nuts reach inside the handguard (reach_inside)","need":"A Magpul figure for the M-LOK T-nut's height"},{"what":"How it sits on the kit's MOE adapter plate (magpul-mlok-hand-stop-moe-adapter, a part since 2026-10-05: D72): by the two parts' figures its band bears on the plate's flat and its ears' tips end 0.013 in past the plate's underside, and its plate runs 0.03 in into the foot of the adapter's moulded cover one way round","need":"A view of the stop on the plate from its end or its side with a scale: the band's depth here (the patent's outermost line) and the plate's thickness (two photos through fitted cameras) are each good to a hundredth"},{"what":"How far its ears stand above the band between them: the patent's outermost line there is 0.116 in, and the image of it installed has its plate 0.04 in thinner than the patent's (the ledger's height)","need":"A view of it from the plate's end with a scale, or of its mounting side beside the T-nuts"},{"what":"The source page of the user's photo","need":"The gallery it was screenshotted from, for the manifest"}]},"magpul-mlok-index-panel":{"id":"magpul-mlok-index-panel","name":"M-LOK Index Panel","manufacturer":"Magpul","url":"https://magpul.com/m-lok-handstop-kit.html","category":"hand_stop","description":"The index panel of Magpul's M-LOK Hand Stop Kit (MAG608), sold only in that kit: a low fin that gives the support hand a reference point, on a plate one M-LOK slot long. Magpul: \"one M-LOK Index panel, which is reversible for a custom fit\". Black, FDE, ODG, Stealth Gray.","weight":"magpul-mlok-index-panel.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"lug":{"origin":["{.lug_x} + {std.mlok.interval} / 2","{.mounting_band_depth}",0],"note":"The middle of its two pairs of bosses on the band between its ears, which is the face that bears on a handguard (mounting_band_depth below the ears' tips, where the part's frame has y 0: the same plate as the hand stop's). Its one screw and T-nut are at lug_x, in the rear half of the slot; a second pair of bosses with no screw stands one M-LOK interval ahead of it, either side of the fin's hollow, in the front half (FIG. 7; 20.0 mm by the plan's own scale). The middle of the two is the plate's middle within 0.001 in: what an M-LOK position places."}},"interfaces":{"mlok":{"type":"mlok","role":"accessory","anchor":"lug","params":{"lugs":"={.lugs}","reach_inside":"={.reach_inside}"},"flips":true,"note":"One slot: its plate is one slot pitch long and its screw and its second pair of bosses 20 mm apart (the patent's top plan). Reversible, in Magpul's word: unflipped its fin is at the front of its plate, flipped at the rear. How far its T-nut reaches inside isn't published."}},"materials":{"body":{"label":"Index panel","finish":"polymer","recolorable":true,"color":"magpul-black","sheen":"matte","options":{"black":{"label":"Black","finish":"polymer","color":"magpul-black","sheen":"matte","source":"https://magpul.com/m-lok-handstop-kit.html"},"fde":{"label":"FDE","finish":"polymer","color":"magpul-fde","sheen":"matte","source":"https://magpul.com/m-lok-handstop-kit.html"},"odg":{"label":"ODG","finish":"polymer","color":"magpul-odg","sheen":"matte","source":"https://magpul.com/m-lok-handstop-kit.html"},"sgy":{"label":"Stealth Gray","finish":"polymer","color":"magpul-stealth-gray","sheen":"matte","source":"https://magpul.com/m-lok-handstop-kit.html"}},"default":"black","note":"Magpul's polymer, in the four colours the kit is sold in (the page's swatches: Black, Flat Dark Earth, Olive Drab Green, Stealth Gray), as matched on the MOE SL. The panel has no number of its own: the kit's numbers (MAG608-BLK and so on) are the kit's. The kit isn't sold in Modified Coyote Brown (its page, read 2026-10-06 on the harvested copy: four swatches). The plate and the fin are one moulding in the kit's colour."},"screws":{"label":"Screw","finish":"steel","recolorable":false,"color":"placeholder-black","note":"Its one screw: black on the FDE kit as on the black one (Magpul's gallery picture of the FDE kit put together, mag608_fde_2: a blue-black head in the tan dish), and dark grey with the T-nuts in Wing Tactical's photo of the ODG kit's hardware. A steel screw, its coating not stated by anyone: drawn as dark steel in the placeholder black, the same in every colour of the kit. The T-nut is inside the hand guard and isn't drawn."}},"components":{},"geometry":{"model":"magpul-mlok-index-panel.glb","components":{},"approximations":["Magpul's design patent's three views (US D755,334 S: the left side elevation, FIG. 5; the front elevation, FIG. 3; the bottom plan, FIG. 8), scaled to the plate's length as the user's gallery image has it (the handguard's rail teeth the scale), and what they allow together: a hull. Inside it the plate is cut to its own section from FIG. 3 (its outer face dished as its mounting side is: 0.13 in of plate at the middle, thinning to the ears), and the fin to FIG. 8's lines: its footprint on the plate, its section where its fillets end and the rim across its tip, each thinner toward the sides (0.32 in at the middle and 0.13 at the sides where the fillets end; 0.18 and 0.10 at the tip), with straight faces drawn from one to the next. Those three are read where the drawing's lines cross ten columns; toward the sides its lines cross and fan, and the outermost two columns carry the run on.","It bears on the band between its ears (FIG. 3: 0.111 in below their tips, 0.68 in across, in broken lines), as the hand stop does, and its ears run down either side of the handguard's face. The bosses and the lug that stand in the slot above the band (broken lines; Wing Tactical's photo shows them) and the fin's hollow from the mounting side aren't drawn.","The screw's hole and its recess are cut where FIG. 8 has them, at its diameters; no view gives the recess's depth, and it is drawn as a countersink at 45 degrees from its rim to its innermost circle (0.035 in). The screw's head is drawn (2026-10-06) as a low dome on the dish's floor: as wide as Magpul's picture of the FDE kit has it (0.36 in, the dish's innermost circle within the reading) and its crown 0.034 in out of the plate, as the user's side view has it; its profile between the two and its six-lobe socket aren't sourced, and the socket isn't drawn.","The fin's two faces are dished inside its rim (FIG. 2) by an amount no elevation gives: drawn flat. The texture round the screw isn't drawn; the shallow hollow there (0.016 in) is the side elevation's broken line. Edges broken at 0.012 in.","Where its fin and its screw are along the plate is the patent's, on which three views agree; the user's image has both 0.06 to 0.08 in nearer the fin's end (the ledger's lug_x and fin_x keep both readings)."],"ledger":["magpul-mlok-index-panel.length","magpul-mlok-index-panel.height","magpul-mlok-index-panel.width","magpul-mlok-index-panel.lug_x","magpul-mlok-index-panel.mounting_band_depth","magpul-mlok-index-panel.screw_hole_diameter","magpul-mlok-index-panel.screw_recess_diameter","magpul-mlok-index-panel.screw_recess_floor_diameter","magpul-mlok-index-panel.screw_head_diameter","magpul-mlok-index-panel.screw_head_proud"]},"profiles":{"side":{"plane":"xy","origin":"the plate's rear end (the end away from the fin) at the ears' tips, the figure's outermost line on the mounting side","offset":{},"points":[[0,0.086],[0.004,0.057],[0.021,0.035],[0.118,0],[1.441,0],[1.467,0.003],[1.55,0.046],[1.558,0.06],[1.558,0.146],[1.552,0.234],[1.543,0.245],[1.38,0.246],[1.34,0.263],[1.303,0.3],[1.284,0.36],[1.217,0.739],[1.208,0.745],[1.05,0.745],[1.036,0.726],[0.967,0.329],[0.947,0.291],[0.907,0.257],[0.866,0.245],[0.603,0.246],[0.565,0.236],[0.415,0.227],[0.226,0.234],[0.171,0.246],[0.016,0.245],[0.004,0.231]],"scaleRefs":["magpul-mlok-index-panel.length"],"inputs":{"magpul-mlok-index-panel.length":1.558},"tolerance":0.006,"photo":"references/magpul-mlok-index-panel c190e3d7fbdd (US D755,334 S (Magpul, 'Index attachment for a firearm'), FIG. 5 left side elevation, 300 dpi)","method":"luminance < 128, inside [853, 620, 1920, 2840], closing ×18, holes filled, notches filled in [853, 700, 900, 2760] (disk closing, r 40 px), inset 2 px (half the outline's stroke); rotated +90.0° as declared; scale from magpul-mlok-index-panel.length = 1.558 in (x-extent 2159 px → 1385.8 px/in); origin at x min, y min of the outline; Douglas-Peucker at 0.006 in with the extremes kept: 30 points (IoU 0.992 with the full outline); checks: (y_max) − (y_max in x [0.15, 0.55]) 0.499 ± 0.008 in vs magpul-mlok-index-panel.fin_height 0.498 ± 0.012 (corroborated): agrees (tools/trace.py)","via":"harvest","note":"The mounting side is a stack of thin lines in the drawing (the outermost in broken strokes): the outline takes the outermost, which the front elevation has as the ears' tips. The band that bears on a handguard is behind the ears in this view. Round the screw the outer face's heavy line stops and a broken one bows 0.016 in into the plate instead (rows 880 to 1500: the textured pad's field): the outline follows it, there being no other line."},"front":{"plane":"zy","origin":"the ears' tips, centred","offset":{},"points":[[-0.519,0.025],[-0.515,0.006],[-0.503,0],[-0.345,0.11],[0.339,0.112],[0.507,0],[0.518,0.008],[0.519,0.026],[0.504,0.124],[0.339,0.583],[0.321,0.614],[0.263,0.665],[0.166,0.714],[0.092,0.735],[-0.006,0.745],[-0.092,0.735],[-0.173,0.712],[-0.256,0.671],[-0.315,0.624],[-0.367,0.512],[-0.503,0.128]],"features":{"plate":[[[0.558,-0.036],[-0.558,-0.036],[-0.558,0.038],[-0.513,0.055],[-0.477,0.089],[-0.44,0.124],[-0.403,0.159],[-0.366,0.19],[-0.329,0.21],[-0.292,0.219],[-0.255,0.226],[-0.218,0.231],[-0.181,0.235],[-0.145,0.239],[-0.108,0.242],[-0.071,0.243],[-0.034,0.245],[0,0.245],[0.034,0.245],[0.071,0.243],[0.108,0.242],[0.145,0.239],[0.181,0.235],[0.218,0.231],[0.255,0.226],[0.292,0.219],[0.329,0.21],[0.366,0.19],[0.403,0.159],[0.44,0.124],[0.477,0.089],[0.513,0.055],[0.558,0.038]]]},"scaleRefs":["magpul-mlok-index-panel.height","magpul-mlok-index-panel.width"],"inputs":{"magpul-mlok-index-panel.height":0.745,"magpul-mlok-index-panel.width":1.038},"tolerance":0.006,"photo":"references/magpul-mlok-index-panel 46bdaee98acd (US D755,334 S (Magpul, 'Index attachment for a firearm'), FIG. 3 front elevation, 300 dpi)","method":"luminance < 128, inside [560, 560, 2030, 1640], 1 boxes excluded, closing ×18, holes filled, notches filled in [840, 700, 1760, 780] (disk closing, r 40 px), inset 2 px (half the outline's stroke); rotated +180.0° as declared; scale from magpul-mlok-index-panel.height = 0.745 in (y-extent 1010 px → 1355.7 px/in) and magpul-mlok-index-panel.width = 1.038 in (x-extent 1407 px → 1355.5 px/in), which agree within 0.0%; mean 1355.6 px/in; origin at x center, y min of the outline; Douglas-Peucker at 0.006 in with the extremes kept: 21 points (IoU 0.990 with the full outline); features through the same placement (plate: The plate's section: the mounting side of its outer face, which is dished as the mounting side is (0.24 in from the ears' tips at the middle, 0.05 at the ears).) (tools/trace.py)","via":"harvest","note":"Symmetric. The ears' tips are the top (y 0); the band between them is the mounting face. The vertical strokes on the fin are the drawing's shading, not ribs."},"plan":{"plane":"xz","origin":"the plate's rear end (the screw's end), centred","offset":{},"points":[[0,0.436],[0,0],[0,-0.437],[0.003,-0.453],[0.023,-0.473],[0.082,-0.509],[0.115,-0.519],[1.442,-0.519],[1.482,-0.504],[1.486,-0.507],[1.539,-0.469],[1.558,-0.436],[1.559,0.429],[1.554,0.451],[1.54,0.469],[1.483,0.505],[1.449,0.518],[0.123,0.519],[0.08,0.508],[0.022,0.471],[0.007,0.455]],"features":{"fin_foot":[[[1.307,0.518],[1.312,0.502],[1.329,0.451],[1.345,0.401],[1.368,0.351],[1.385,0.301],[1.393,0.251],[1.396,0.2],[1.399,0.1],[1.404,0],[1.399,-0.1],[1.396,-0.2],[1.393,-0.251],[1.385,-0.301],[1.368,-0.351],[1.345,-0.401],[1.329,-0.451],[1.312,-0.502],[1.307,-0.518],[0.953,-0.518],[0.948,-0.502],[0.931,-0.451],[0.915,-0.401],[0.892,-0.351],[0.875,-0.301],[0.867,-0.251],[0.864,-0.2],[0.861,-0.1],[0.856,0],[0.861,0.1],[0.864,0.2],[0.867,0.251],[0.875,0.301],[0.892,0.351],[0.915,0.401],[0.931,0.451],[0.948,0.502],[0.953,0.518]]],"fin_root":[[[1.193,0.518],[1.197,0.502],[1.212,0.451],[1.228,0.401],[1.247,0.351],[1.264,0.301],[1.276,0.251],[1.281,0.2],[1.284,0.1],[1.289,0],[1.284,-0.1],[1.281,-0.2],[1.276,-0.251],[1.264,-0.301],[1.247,-0.351],[1.228,-0.401],[1.212,-0.451],[1.197,-0.502],[1.193,-0.518],[1.067,-0.518],[1.063,-0.502],[1.048,-0.451],[1.032,-0.401],[1.013,-0.351],[0.996,-0.301],[0.984,-0.251],[0.979,-0.2],[0.976,-0.1],[0.971,0],[0.976,0.1],[0.979,0.2],[0.984,0.251],[0.996,0.301],[1.013,0.351],[1.032,0.401],[1.048,0.451],[1.063,0.502],[1.067,0.518]]],"fin_tip":[[[1.178,0.518],[1.178,0.502],[1.178,0.451],[1.179,0.401],[1.182,0.351],[1.183,0.301],[1.192,0.251],[1.202,0.2],[1.217,0.1],[1.219,0],[1.217,-0.1],[1.202,-0.2],[1.192,-0.251],[1.183,-0.301],[1.182,-0.351],[1.179,-0.401],[1.178,-0.451],[1.178,-0.502],[1.178,-0.518],[1.081,-0.518],[1.081,-0.502],[1.081,-0.451],[1.081,-0.401],[1.078,-0.351],[1.077,-0.301],[1.068,-0.251],[1.058,-0.2],[1.043,-0.1],[1.041,0],[1.043,0.1],[1.058,0.2],[1.068,0.251],[1.077,0.301],[1.078,0.351],[1.081,0.401],[1.081,0.451],[1.081,0.502],[1.081,0.518]]]},"scaleRefs":["magpul-mlok-index-panel.length","magpul-mlok-index-panel.width"],"inputs":{"magpul-mlok-index-panel.length":1.558,"magpul-mlok-index-panel.width":1.038},"tolerance":0.004,"photo":"references/magpul-mlok-index-panel 0c155e219281 (US D755,334 S (Magpul, 'Index attachment for a firearm'), FIG. 8 bottom plan, 300 dpi)","method":"luminance < 128, inside [600, 750, 1920, 2680], closing ×18, holes filled, inset 2 px (half the outline's stroke); rotated -90.0° as declared; scale from magpul-mlok-index-panel.length = 1.558 in (x-extent 1863 px → 1195.8 px/in) and magpul-mlok-index-panel.width = 1.038 in (y-extent 1240 px → 1194.6 px/in), which agree within 0.1%; mean 1195.2 px/in; origin at x min, y center of the outline; Douglas-Peucker at 0.004 in with the extremes kept: 21 points (IoU 0.999 with the full outline); features through the same placement (fin_foot: The fin's footprint on the plate (where its fillets run out): 0.55 in along the plate at the middle, 0.36 at the sides.; fin_root: The fin where its fillets end and its two faces straighten: 0.32 in along the plate at the middle (the side elevation's there), 0.13 at the sides.; fin_tip: The rim across the fin's tip and up its flanks: 0.18 in along the plate at the middle, 0.10 from a third of an inch out.) (tools/trace.py)","via":"harvest","note":"Symmetric. The screw's hole and recess (broken circles) are ledger figures, not in the outline."}},"gaps":[{"what":"How far the T-nut reaches inside the handguard (reach_inside)","need":"A Magpul figure for the M-LOK T-nut's height"},{"what":"A size for it from its maker (its length, height and width are read from an image and a patent)","need":"A Magpul drawing or figure for the kit's pieces, or a seller's measurement"},{"what":"How deep the screw's recess is, and how far the fin's faces are dished","need":"A section, or a close photo square to the fin's edge"},{"what":"The source page of the user's photo","need":"The gallery it was screenshotted from, for the manifest"}]},"magpul-mlok-mvg":{"id":"magpul-mlok-mvg","name":"M-LOK MVG vertical grip","manufacturer":"Magpul","sku":"MAG597","url":"https://magpul.com/m-lok-mvg-vertical-grip.html","category":"vertical_grip","description":"Magpul's M-LOK MVG: a 3 in polymer vertical grip with the TSP texture, mounting directly to M-LOK slots with two T-nuts. Black, FDE, ODG, Stealth Gray (and Modified Coyote Brown, 2026).","weight":"magpul-mlok-mvg.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"lug":{"origin":["{.lug_x} + {.lug_spacing} / 2",0,0],"note":"The middle of its two T-nuts on the mounting face: what an M-LOK position places. Since 2026-10-05 the middle of the two, not the rear one: a slot's position is its centre, and two nuts the M-LOK interval apart go one in each half of it (the rear nut on the centre put the front one 4 mm past the slot's end, over the web). The part frame's origin is the plate's rear end on that face."}},"interfaces":{"mlok":{"type":"mlok","role":"accessory","anchor":"lug","params":{"lugs":"={.lugs}","reach_inside":"={.reach_inside}"},"flips":true,"note":"Two T-nuts the M-LOK interval apart in one slot (the installation sheet, Step 3: \"Place the M-LOK T-Nuts and lugs into the slot\"). How far the nuts reach inside isn't published, so that check reads as unmade."}},"materials":{"body":{"label":"Grip","finish":"polymer","recolorable":true,"color":"magpul-black","sheen":"matte","options":{"black":{"label":"Black","finish":"polymer","color":"magpul-black","sheen":"matte","sku":"MAG597-BLK","source":"https://magpul.com/m-lok-mvg-vertical-grip.html"},"fde":{"label":"FDE","finish":"polymer","color":"magpul-fde","sheen":"matte","sku":"MAG597-FDE","source":"https://magpul.com/m-lok-mvg-vertical-grip.html"},"mcb":{"label":"Modified Coyote Brown","finish":"polymer","color":"magpul-mcb","sheen":"matte","sku":"MAG597-MCB","source":"https://magpul.com/m-lok-mvg-vertical-grip.html"},"odg":{"label":"ODG","finish":"polymer","color":"magpul-odg","sheen":"matte","sku":"MAG597-ODG","source":"https://magpul.com/m-lok-mvg-vertical-grip.html"},"sgy":{"label":"Stealth Gray","finish":"polymer","color":"magpul-stealth-gray","sheen":"matte","sku":"MAG597-GRY","source":"https://magpul.com/m-lok-mvg-vertical-grip.html"}},"default":"black","note":"Magpul's reinforced polymer with the TSP texture, drawn as one matte polymer. The five colours Magpul's page offers MAG597 in (its swatches: Black, Flat Dark Earth, Modified Coyote Brown, Olive Drab Green, Stealth Gray): four as matched on the MOE SL, Modified Coyote Brown as matched on the CTR's gallery photos and checked on this grip's (data/colors/magpul.yaml). The grip is one moulding and one colour all over in each, its mounting face and its hollow included (Magpul's gallery shots 01.1 to 03.1 of each); the two screws and T-nuts sit inside it and the handguard and aren't drawn."}},"components":{},"geometry":{"model":"magpul-mlok-mvg.glb","components":{},"approximations":["Built in the round from Primary Arms' side view and Magpul's design patent (US D745,628 S): at every height the base's oval section (FIG. 7, scaled by the 1.54 in length and 1.17 in width on file, which fit it to 0.3%) put to the side outline's length there. Above the grip's middle its sides are cut flat to the front elevation's width (FIG. 2), as the patent's top plan draws the plate's long sides; that the neck's sides are flat too is read from the patent's views, and no photo on file is straight enough to check it.","The front elevation's height over its width is 5% off the figures on file, so its height is put to the side view's 3.0 in and its shape kept (the waist where the patent draws it, as a share of the height).","The 16 grooves across each end are where the side photo has them (their pitch, depth and width measured on its two edges) and as long across as the patent's front view draws them, 0.70 in, which the photo agrees with: they stop 0.124 in from each edge in it, and 0.127 by the patent's section. Their walls are drawn sloped at 60° and their ends run out over half their width.","Hollow and open at the base, as Magpul's installation sheet and its photos from below have it (the screws go in through the bottom). The wall is the 0.115 in the patent's bottom plan shows round the opening, drawn that thick all over, the top included: no view on file shows the inside. In the renderer the hollow is lit as evenly as the outside, so from straight below it reads lighter than a real one, which is dark.","The small step under the neck (0.012 in, at 0.8 in below the mounting face in the side photo) runs level all round; how it runs across the sides isn't in a straight view. The plate's top edge is broken along its sides as the side view has it at its ends.","The two lugs and the screws' holes in the mounting face, the TSP texture and the MVG lettering aren't drawn. The T-nuts and screws aren't drawn: they sit inside the handguard."],"ledger":["magpul-mlok-mvg.length","magpul-mlok-mvg.height","magpul-mlok-mvg.width","magpul-mlok-mvg.lug_x","magpul-mlok-mvg.rib_grooves","magpul-mlok-mvg.rib_groove_pitch","magpul-mlok-mvg.rib_groove_first_y","magpul-mlok-mvg.rib_groove_depth","magpul-mlok-mvg.rib_groove_width","magpul-mlok-mvg.rib_groove_length","magpul-mlok-mvg.base_wall"]},"profiles":{"side":{"plane":"xy","origin":"the plate's rear end on the mounting face (its top surface, which bears on the handguard)","offset":{},"points":[[0,1.77],[0.029,1.736],[0.032,1.707],[0.009,1.692],[0.003,1.681],[0.026,1.662],[0.034,1.636],[0.034,1.628],[0.005,1.599],[0.008,1.588],[0.026,1.575],[0.032,1.554],[0.029,1.535],[0.005,1.517],[0.026,1.488],[0.034,1.453],[0.005,1.427],[0.005,1.419],[0.026,1.401],[0.034,1.382],[0.032,1.369],[0.003,1.345],[0.016,1.203],[0.026,1.184],[0.029,1.158],[0.05,1.121],[0.058,1.084],[0.069,1.073],[0.069,1.05],[0.092,0.983],[0.095,0.954],[0.106,0.939],[0.106,0.91],[0.121,0.851],[0.121,0.801],[0.135,0.772],[0.137,0.73],[0.137,0.461],[0.124,0.389],[0.087,0.286],[0.013,0.173],[0.003,0.144],[0.003,0.057],[0.016,0.028],[0.075,0],[0.413,0],[0.429,0.005],[0.445,0],[0.561,0],[0.58,0.005],[0.598,0],[0.894,0],[0.902,0.008],[0.936,0.003],[0.952,0.008],[1.02,0.005],[1.026,0.011],[1.036,0.011],[1.044,0.003],[1.065,0.013],[1.081,0.008],[1.176,0.011],[1.184,0.005],[1.226,0.005],[1.232,0],[1.414,0],[1.427,0.008],[1.469,0.013],[1.517,0.029],[1.547,0.054],[1.55,0.086],[1.55,0.133],[1.534,0.173],[1.494,0.228],[1.452,0.305],[1.418,0.397],[1.418,0.434],[1.405,0.466],[1.405,0.801],[1.418,0.817],[1.42,0.891],[1.484,1.113],[1.497,1.137],[1.526,1.226],[1.526,1.258],[1.537,1.3],[1.537,1.369],[1.53,1.378],[1.514,1.378],[1.508,1.385],[1.516,1.411],[1.539,1.443],[1.516,1.477],[1.542,1.527],[1.508,1.554],[1.518,1.585],[1.537,1.607],[1.537,1.622],[1.527,1.629],[1.519,1.626],[1.508,1.644],[1.516,1.665],[1.539,1.694],[1.539,1.707],[1.51,1.731],[1.513,1.747],[1.539,1.789],[1.53,1.801],[1.519,1.801],[1.508,1.81],[1.516,1.834],[1.539,1.863],[1.539,1.871],[1.516,1.9],[1.539,1.95],[1.539,1.966],[1.508,1.982],[1.518,2.011],[1.539,2.034],[1.534,2.05],[1.516,2.066],[1.518,2.084],[1.539,2.116],[1.537,2.137],[1.508,2.153],[1.513,2.172],[1.539,2.206],[1.539,2.216],[1.516,2.24],[1.523,2.264],[1.539,2.285],[1.539,2.298],[1.521,2.319],[1.518,2.333],[1.539,2.38],[1.539,2.391],[1.521,2.409],[1.518,2.42],[1.539,2.457],[1.539,2.475],[1.518,2.499],[1.523,2.517],[1.539,2.536],[1.542,2.554],[1.518,2.583],[1.521,2.602],[1.542,2.636],[1.518,2.671],[1.521,2.689],[1.539,2.71],[1.537,2.782],[1.526,2.805],[1.523,2.887],[1.51,2.948],[1.483,2.978],[1.467,2.981],[1.356,2.981],[1.308,2.97],[1.139,2.973],[1.071,2.968],[0.999,2.973],[0.97,2.968],[0.659,2.973],[0.635,2.968],[0.334,2.97],[0.276,2.965],[0.234,2.97],[0.078,2.97],[0.054,2.962],[0.029,2.924],[0.029,2.853],[0.016,2.824],[0.016,2.75],[0.003,2.718],[0.034,2.663],[0.005,2.639],[0.008,2.623],[0.037,2.583],[0.005,2.536],[0.026,2.517],[0.034,2.491],[0.016,2.467],[0.011,2.449],[0.037,2.412],[0.034,2.399],[0.013,2.378],[0.016,2.351],[0.029,2.338],[0.037,2.317],[0.008,2.288],[0.032,2.248],[0.034,2.23],[0.013,2.211],[0.005,2.195],[0.026,2.18],[0.034,2.145],[0.008,2.119],[0.008,2.103],[0.026,2.09],[0.034,2.069],[0.034,2.053],[0.008,2.026],[0.008,2.016],[0.029,1.995],[0.034,1.971],[0.005,1.945],[0.008,1.934],[0.026,1.918],[0.034,1.894],[0.034,1.886],[0.005,1.863],[0.005,1.852],[0.026,1.834],[0.034,1.797]],"scaleRefs":["magpul-mlok-mvg.height","magpul-mlok-mvg.length"],"inputs":{"magpul-mlok-mvg.height":3,"magpul-mlok-mvg.length":1.54},"tolerance":0.004,"photo":"references/magpul-mlok-mvg dc38ca0e3fdf (Primary Arms MAG597-ODG_00.jpg: the MVG alone on white, upright, a straight side view along the handguard, 2000 x 1334)","method":"luminance < 215, inside [600, 137, 1400, 1320], closing ×2, largest piece, holes filled; rotated +180.0° as declared; scale from magpul-mlok-mvg.height = 3 in (y-extent 1129 px → 376.3 px/in) and magpul-mlok-mvg.length = 1.54 in (x-extent 587 px → 381.2 px/in), which agree within 1.3%; mean 378.8 px/in; origin at x min, y min of the outline; Douglas-Peucker at 0.004 in with the extremes kept: 214 points (IoU 0.998 with the full outline) (tools/trace.py)","via":"harvest","note":"Primary Arms' straight side view, scaled by Wing Tactical's length and Magpul's height together (they agree within 2%). The T-nuts above the plate are left out of the outline."},"plan":{"plane":"xz","origin":"the section's rear end (the side outline's x = 0), centred across","offset":{},"points":[[0,-0.003],[0.016,-0.141],[0.063,-0.263],[0.127,-0.354],[0.224,-0.438],[0.328,-0.49],[0.425,-0.513],[0.536,-0.553],[0.677,-0.58],[0.809,-0.583],[0.984,-0.56],[1.114,-0.514],[1.205,-0.495],[1.301,-0.451],[1.363,-0.407],[1.439,-0.33],[1.494,-0.244],[1.533,-0.127],[1.546,0.029],[1.526,0.153],[1.483,0.263],[1.413,0.361],[1.324,0.436],[1.209,0.493],[1.121,0.511],[0.976,0.562],[0.867,0.58],[0.731,0.583],[0.563,0.56],[0.43,0.514],[0.341,0.495],[0.269,0.464],[0.202,0.423],[0.107,0.33],[0.055,0.247],[0.013,0.127],[0.002,0]],"scaleRefs":["magpul-mlok-mvg.length","magpul-mlok-mvg.width"],"inputs":{"magpul-mlok-mvg.length":1.54,"magpul-mlok-mvg.width":1.17},"tolerance":0.005,"photo":"references/magpul-mlok-mvg 9d49858cd908 (US D745,628 S (Magpul MVG), FIG. 7 bottom plan, 300 dpi)","method":"luminance < 128, inside [780, 1935, 1778, 2700], closing ×3, largest piece, holes filled, inset 2 px (half the outline's stroke); scale from magpul-mlok-mvg.length = 1.54 in (x-extent 951 px → 617.5 px/in) and magpul-mlok-mvg.width = 1.17 in (y-extent 717 px → 612.8 px/in), which agree within 0.8%; mean 615.2 px/in; origin at x min, y center of the outline; Douglas-Peucker at 0.005 in with the extremes kept: 37 points (IoU 0.994 with the full outline) (tools/trace.py)","via":"harvest","note":"Symmetric both ways; the nested outlines inside it are its bottom's chamfer and recess."},"front":{"plane":"zy","origin":"the mounting face (the plate's top, y = 0, as the side outline's), centred across; the grip below it in +y, as the side outline has it","offset":{},"points":[[-0.585,1.21],[-0.564,1.054],[-0.494,0.758],[-0.466,0.483],[-0.473,0.214],[-0.516,0.032],[-0.503,0.043],[0.034,0.043],[0.047,0.033],[0.058,0.043],[0.503,0.043],[0.514,0],[0.516,0.066],[0.473,0.223],[0.466,0.448],[0.494,0.751],[0.585,1.178],[0.585,2.609],[0.556,2.788],[0.526,2.822],[-0.004,2.842],[-0.498,2.827],[-0.533,2.817],[-0.554,2.788],[-0.585,2.59]],"scaleRefs":["magpul-mlok-mvg.width"],"inputs":{"magpul-mlok-mvg.width":1.17},"tolerance":0.01,"photo":"references/magpul-mlok-mvg 2da0ba7d369f (US D745,628 S (Magpul MVG), sheet 2, FIG. 2 front elevation, 300 dpi)","method":"luminance < 128, inside [470, 905, 1190, 2625], 1 boxes excluded, closing ×4, largest piece, holes filled, inset 2 px (half the outline's stroke); rotated +180.0° as declared; scale from magpul-mlok-mvg.width = 1.17 in (x-extent 680 px → 581.2 px/in); origin at x center, y min of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 25 points (IoU 0.996 with the full outline); checks: height 2.842 ± 0.049 in vs magpul-mlok-mvg.height 3 ± 0.05 (confirmed): DISAGREES (tools/trace.py)","via":"harvest","note":"The grip seen from its front: the plate full width, the waist below it, the ribbed half full width to a rounded bottom. Its shape, not its proportions: the model puts its height to the side view's."}},"gaps":[{"what":"How far the T-nuts reach inside the handguard (reach_inside)","need":"A Magpul figure or drawing of the M-LOK T-nut's height, or a straight photo of a nut beside its 7 mm flats; the FAQ says the nut's drawings are restricted"}]},"magpul-mlok-polymer-rail-section-11-slot":{"id":"magpul-mlok-polymer-rail-section-11-slot","name":"M-LOK® Polymer Rail, 11 Slots","manufacturer":"Magpul","sku":"MAG593","url":"https://magpul.com/m-lokpolymerrailsection-11slots.html","category":"rail_section","description":"A 11-slot Picatinny rail in Magpul's polymer that bolts straight to a hand guard's M-LOK slots, for a light, a grip or another rail-mounted accessory. Magpul: \"Our polymer rail segment attaches to any M-LOK interface for a 11-slot Picatinny mount for lights, vertical grips, or other 1913 rail compatible accessories.\" It has three screw holes, in the second, the sixth and the tenth slots, four pitches (40 mm) apart, cammed T-nuts and recoil lugs under it, and bevelled ends. Black only (MAG593-BLK). NSN 1005-01-725-4945.","weight":"magpul-mlok-polymer-rail-section-11-slot.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"lug":{"origin":["{.lug_x}",0,0],"note":"The centre of the M-LOK slot its rear T-nut is in, on its mounting face: what an M-LOK position places. Its rear screw hole is at the centre of its rail slot {.rear_hole_slot}, and its T-nut half the M-LOK interval behind this point, in the rear half of the slot (which half isn't published: the ledger's lug_x says so). Rail section frame: origin at its rear end on the mounting face, +x toward the muzzle, +y away from the face."},"top_rail":{"origin":["{.rail_slot0_x}","{.height}",0],"note":"The rearmost rail slot's centre on the rail's top: what a clamp's position places, a slot further forward for each index."}},"interfaces":{"mlok":{"type":"mlok","role":"accessory","anchor":"lug","params":{"lugs":"={.lugs}","reach_inside":"={.reach_inside}"},"flips":true,"note":"Three M-LOK slots, with the screws in its end holes (80 mm apart): a T-nut in the rear half of one slot and one in the rear half of the slot two on. Magpul's sheet: \"All hardware necessary for attachment directly to M-LOK Slots on either aluminum or polymer hand guards and forends is included.\" How far its nuts and lugs reach inside isn't published."},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}"},"flips":false,"note":"What clamps to a Picatinny rail is mounted here (D72: a mount that carries others). Magpul: \"for lights, vertical grips, or other 1913 rail compatible accessories\"; its sheet: \"various 1913 Picatinny spec rail-mounted accessories such as lights, vertical grips, etc.\" Its slots are on the standard's pitch, centred on its length."}},"materials":{"body":{"label":"Rail section","finish":"polymer","recolorable":true,"color":"magpul-black","sheen":"matte","options":{"black":{"label":"Black","finish":"polymer","color":"magpul-black","sheen":"matte","sku":"MAG593-BLK","source":"https://magpul.com/m-lokpolymerrailsection-11slots.html"}},"default":"black","note":"Magpul's polymer (its sheet: \"Injection molded from a proprietary reinforced composite for enhanced strength and durability while remaining lightweight\"; its page: \"Constructed of Magpul's light, durable polymer\"), in black, the one colour Magpul sells it in (its page's one variant, MAG593_RET_BLK_; the sheet's colour line, \"BLK\"), as matched on the MOE SL (magpul-black). One moulding: the sheet's and the page's photos have it one black all over. No other colour of any of the five lengths is sold (Magpul's pages and every seller's read)."},"screws":{"label":"Screws","finish":"steel","recolorable":false,"color":"placeholder-black","note":"Its two screws' heads in their recesses: black socket button heads in every photo of the part fitted (Magpul's), and in its photos of the hardware under the 5- and 7-slot sections. Black steel in its one colourway."}},"components":{},"geometry":{"model":"magpul-mlok-polymer-rail-section-11-slot.glb","components":{},"approximations":["Its section is the standard's rail head (MIL-STD-1913's Figure 1 from the ledger, lib.rail_head), its lower faces carried on at 45 degrees to a neck 0.2 in under the rail's top (assumed: no view along the rail is on file, and a clamp's jaws need room there), the neck upright down to a shoulder a little over the mounting face (the 5-slot's underside photo reads 0.055 in; assumed on the others), and below it the body as wide as its outline from above, straight sided; its rail slots at the standard's width, depth and pitch, centred on its length (as its own photos have them).","Its length is read on Magpul's own photos by its rail slots at the standard's pitch, 0.12 to 0.18 in under Magpul's \"max overall length\" for the longer lengths (the ledger keeps both, and says why).","Its height is read on Magpul's studio photos of the 7- and the 9-slot (the top's foreshortening for the camera's elevation, the band below it for the side); for this length it is that reading or an assumption that says so in the ledger.","Each end slopes from where its top's flat ends down to a short upright face at the mounting face, along a quarter ellipse (the photos show a rounded slope, how round isn't read), and its corners are cut off in plan at the read slant; the M moulded on one end's slope isn't drawn.","Each screw hole goes straight through, in a round recess (a counterbore with a flat floor at an assumed height, its walls upright) that cuts into the slot it is in and the lands either side, as the photos from above show it. The screws' heads are domes on the recess's floor, their socket not drawn; their heads are drawn in its two end holes (the middle one is drawn empty).","The underside is drawn flat. On the part it is a rim round a pocket, with the cammed seats round each hole and rectangular recoil lugs between the holes, which stand into the hand guard's slots (Magpul's underside photos); the cammed steel T-nuts under the hand guard's face aren't drawn either.","Its weight is worked out: the model's polymer volume times a nylon's density (std.density.polymer), the screws' heads apart. Magpul states none."],"ledger":["magpul-mlok-polymer-rail-section-11-slot.length","magpul-mlok-polymer-rail-section-11-slot.height","magpul-mlok-polymer-rail-section-11-slot.width","magpul-mlok-polymer-rail-section-11-slot.rail_slot0_x","magpul-mlok-polymer-rail-section-11-slot.lug_x","magpul-mlok-polymer-rail-section-11-slot.neck_top_below_top","magpul-mlok-polymer-rail-section-11-slot.neck_foot_above_face","magpul-mlok-polymer-rail-section-11-slot.end_bevel_length","magpul-mlok-polymer-rail-section-11-slot.end_corner_chamfer","magpul-mlok-polymer-rail-section-11-slot.counterbore_diameter","magpul-mlok-polymer-rail-section-11-slot.screw_head_diameter"]},"profiles":{},"gaps":[{"what":"Magpul's own height, width and weight for it","need":"A specification table or a drawing from Magpul; a seller's measured figures; or a level side view or end view of it with a scale (its own rail slots in frame)"},{"what":"Where its T-nuts sit in an M-LOK slot, and how far they and its recoil lugs reach inside (reach_inside)","need":"Magpul's instruction for the rail sections, or a side view of one fitted to a hand guard with the slots in frame"},{"what":"The underside's pocket, its rim and its lugs","need":"A square view of its underside with a scale; drawn flat meanwhile"},{"what":"Which two of its three holes its two screws go in","need":"Magpul's word on the \"intermediate spacing option\"; the model has them in the end holes"}]},"magpul-mlok-polymer-rail-section-3-slot":{"id":"magpul-mlok-polymer-rail-section-3-slot","name":"M-LOK® Polymer Rail, 3 Slots","manufacturer":"Magpul","sku":"MAG589","url":"https://magpul.com/m-lokpolymerrailsection-3slots.html","category":"rail_section","description":"A 3-slot Picatinny rail in Magpul's polymer that bolts straight to a hand guard's M-LOK slots, for a light, a grip or another rail-mounted accessory. Magpul: \"Our polymer rail segment attaches to any M-LOK interface for a 3-slot Picatinny mount for lights, vertical grips, or other 1913 rail compatible accessories.\" It has a screw hole in each end slot, two pitches apart (the M-LOK interval: both T-nuts in one slot), cammed T-nuts and recoil lugs under it, and bevelled ends. Black only (MAG589-BLK). NSN 1005-01-666-0491.","weight":"magpul-mlok-polymer-rail-section-3-slot.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"lug":{"origin":["{.lug_x}",0,0],"note":"The centre of the M-LOK slot its rear T-nut is in, on its mounting face: what an M-LOK position places. Its rear screw hole is at the centre of its rail slot {.rear_hole_slot}, and its T-nut half the M-LOK interval behind this point, in the rear half of the slot (which half isn't published: the ledger's lug_x says so). Rail section frame: origin at its rear end on the mounting face, +x toward the muzzle, +y away from the face."},"top_rail":{"origin":["{.rail_slot0_x}","{.height}",0],"note":"The rearmost rail slot's centre on the rail's top: what a clamp's position places, a slot further forward for each index."}},"interfaces":{"mlok":{"type":"mlok","role":"accessory","anchor":"lug","params":{"lugs":"={.lugs}","reach_inside":"={.reach_inside}"},"flips":true,"note":"One M-LOK slot: its two T-nuts 20 mm apart, one in each half of it, as Magpul's hand stop's. Magpul's sheet: \"All hardware necessary for attachment directly to M-LOK Slots on either aluminum or polymer hand guards and forends is included.\" How far its nuts and lugs reach inside isn't published."},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}"},"flips":false,"note":"What clamps to a Picatinny rail is mounted here (D72: a mount that carries others). Magpul: \"for lights, vertical grips, or other 1913 rail compatible accessories\"; its sheet: \"various 1913 Picatinny spec rail-mounted accessories such as lights, vertical grips, etc.\" Its slots are on the standard's pitch, centred on its length."}},"materials":{"body":{"label":"Rail section","finish":"polymer","recolorable":true,"color":"magpul-black","sheen":"matte","options":{"black":{"label":"Black","finish":"polymer","color":"magpul-black","sheen":"matte","sku":"MAG589-BLK","source":"https://magpul.com/m-lokpolymerrailsection-3slots.html"}},"default":"black","note":"Magpul's polymer (its sheet: \"Injection molded from a proprietary reinforced composite for enhanced strength and durability while remaining lightweight\"; its page: \"Constructed of Magpul's light, durable polymer\"), in black, the one colour Magpul sells it in (its page's one variant, MAG589_RET_BLK_; the sheet's colour line, \"BLK\"), as matched on the MOE SL (magpul-black). One moulding: the sheet's and the page's photos have it one black all over. No other colour of any of the five lengths is sold (Magpul's pages and every seller's read)."},"screws":{"label":"Screws","finish":"steel","recolorable":false,"color":"placeholder-black","note":"Its two screws' heads in their recesses: black socket button heads in every photo of the part fitted (Magpul's), and in its photos of the hardware under the 5- and 7-slot sections. Black steel in its one colourway."}},"components":{},"geometry":{"model":"magpul-mlok-polymer-rail-section-3-slot.glb","components":{},"approximations":["Its section is the standard's rail head (MIL-STD-1913's Figure 1 from the ledger, lib.rail_head), its lower faces carried on at 45 degrees to a neck 0.2 in under the rail's top (assumed: no view along the rail is on file, and a clamp's jaws need room there), the neck upright down to a shoulder a little over the mounting face (the 5-slot's underside photo reads 0.055 in; assumed on the others), and below it the body as wide as its outline from above, straight sided; its rail slots at the standard's width, depth and pitch, centred on its length (as its own photos have them).","Its length is read on Magpul's own photos by its rail slots at the standard's pitch, 0.12 to 0.18 in under Magpul's \"max overall length\" for the longer lengths (the ledger keeps both, and says why).","Its height is read on Magpul's studio photos of the 7- and the 9-slot (the top's foreshortening for the camera's elevation, the band below it for the side); for this length it is that reading or an assumption that says so in the ledger.","Each end slopes from where its top's flat ends down to a short upright face at the mounting face, along a quarter ellipse (the photos show a rounded slope, how round isn't read), and its corners are cut off in plan at the read slant; the M moulded on one end's slope isn't drawn.","Each screw hole goes straight through, in a round recess (a counterbore with a flat floor at an assumed height, its walls upright) that cuts into the slot it is in and the lands either side, as the photos from above show it. The screws' heads are domes on the recess's floor, their socket not drawn; their heads are drawn in its two holes.","The underside is drawn flat. On the part it is a rim round a pocket, with the cammed seats round each hole and rectangular recoil lugs between the holes, which stand into the hand guard's slots (Magpul's underside photos); the cammed steel T-nuts under the hand guard's face aren't drawn either.","Its weight is worked out: the model's polymer volume times a nylon's density (std.density.polymer), the screws' heads apart. Magpul states none."],"ledger":["magpul-mlok-polymer-rail-section-3-slot.length","magpul-mlok-polymer-rail-section-3-slot.height","magpul-mlok-polymer-rail-section-3-slot.width","magpul-mlok-polymer-rail-section-3-slot.rail_slot0_x","magpul-mlok-polymer-rail-section-3-slot.lug_x","magpul-mlok-polymer-rail-section-3-slot.neck_top_below_top","magpul-mlok-polymer-rail-section-3-slot.neck_foot_above_face","magpul-mlok-polymer-rail-section-3-slot.end_bevel_length","magpul-mlok-polymer-rail-section-3-slot.end_corner_chamfer","magpul-mlok-polymer-rail-section-3-slot.counterbore_diameter","magpul-mlok-polymer-rail-section-3-slot.screw_head_diameter"]},"profiles":{},"gaps":[{"what":"Magpul's own height, width and weight for it","need":"A specification table or a drawing from Magpul; a seller's measured figures; or a level side view or end view of it with a scale (its own rail slots in frame)"},{"what":"Where its T-nuts sit in an M-LOK slot, and how far they and its recoil lugs reach inside (reach_inside)","need":"Magpul's instruction for the rail sections, or a side view of one fitted to a hand guard with the slots in frame"},{"what":"The underside's pocket, its rim and its lugs","need":"A square view of its underside with a scale; drawn flat meanwhile"}]},"magpul-mlok-polymer-rail-section-5-slot":{"id":"magpul-mlok-polymer-rail-section-5-slot","name":"M-LOK® Polymer Rail, 5 Slots","manufacturer":"Magpul","sku":"MAG590","url":"https://magpul.com/m-lokpolymerrailsection-5slots.html","category":"rail_section","description":"A 5-slot Picatinny rail in Magpul's polymer that bolts straight to a hand guard's M-LOK slots, for a light, a grip or another rail-mounted accessory. Magpul: \"Our polymer rail segment attaches to any M-LOK interface for a 5-slot Picatinny mount for lights, vertical grips, or other 1913 rail compatible accessories.\" It has a screw hole in each end slot, four pitches apart (the M-LOK slot pitch: one T-nut in each of two slots), cammed T-nuts and recoil lugs under it, and bevelled ends. Black only (MAG590-BLK). NSN 1005-01-666-0494.","weight":"magpul-mlok-polymer-rail-section-5-slot.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"lug":{"origin":["{.lug_x}",0,0],"note":"The centre of the M-LOK slot its rear T-nut is in, on its mounting face: what an M-LOK position places. Its rear screw hole is at the centre of its rail slot {.rear_hole_slot}, and its T-nut half the M-LOK interval behind this point, in the rear half of the slot (which half isn't published: the ledger's lug_x says so). Rail section frame: origin at its rear end on the mounting face, +x toward the muzzle, +y away from the face."},"top_rail":{"origin":["{.rail_slot0_x}","{.height}",0],"note":"The rearmost rail slot's centre on the rail's top: what a clamp's position places, a slot further forward for each index."}},"interfaces":{"mlok":{"type":"mlok","role":"accessory","anchor":"lug","params":{"lugs":"={.lugs}","reach_inside":"={.reach_inside}"},"flips":true,"note":"Two M-LOK slots: its T-nuts 40 mm apart, each in the rear half of a slot, with the recoil lug under it between them in the first slot's front half. Magpul's sheet: \"All hardware necessary for attachment directly to M-LOK Slots on either aluminum or polymer hand guards and forends is included.\" How far its nuts and lugs reach inside isn't published."},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}"},"flips":false,"note":"What clamps to a Picatinny rail is mounted here (D72: a mount that carries others). Magpul: \"for lights, vertical grips, or other 1913 rail compatible accessories\"; its sheet: \"various 1913 Picatinny spec rail-mounted accessories such as lights, vertical grips, etc.\" Its slots are on the standard's pitch, centred on its length."}},"materials":{"body":{"label":"Rail section","finish":"polymer","recolorable":true,"color":"magpul-black","sheen":"matte","options":{"black":{"label":"Black","finish":"polymer","color":"magpul-black","sheen":"matte","sku":"MAG590-BLK","source":"https://magpul.com/m-lokpolymerrailsection-5slots.html"}},"default":"black","note":"Magpul's polymer (its sheet: \"Injection molded from a proprietary reinforced composite for enhanced strength and durability while remaining lightweight\"; its page: \"Constructed of Magpul's light, durable polymer\"), in black, the one colour Magpul sells it in (its page's one variant, MAG590_RET_BLK_; the sheet's colour line, \"BLK\"), as matched on the MOE SL (magpul-black). One moulding: the sheet's and the page's photos have it one black all over. No other colour of any of the five lengths is sold (Magpul's pages and every seller's read)."},"screws":{"label":"Screws","finish":"steel","recolorable":false,"color":"placeholder-black","note":"Its two screws' heads in their recesses: black socket button heads in every photo of the part fitted (Magpul's), and in its photos of the hardware under the 5- and 7-slot sections. Black steel in its one colourway."}},"components":{},"geometry":{"model":"magpul-mlok-polymer-rail-section-5-slot.glb","components":{},"approximations":["Its section is the standard's rail head (MIL-STD-1913's Figure 1 from the ledger, lib.rail_head), its lower faces carried on at 45 degrees to a neck 0.2 in under the rail's top (assumed: no view along the rail is on file, and a clamp's jaws need room there), the neck upright down to a shoulder a little over the mounting face (the 5-slot's underside photo reads 0.055 in; assumed on the others), and below it the body as wide as its outline from above, straight sided; its rail slots at the standard's width, depth and pitch, centred on its length (as its own photos have them).","Its length is read on Magpul's own photos by its rail slots at the standard's pitch, 0.12 to 0.18 in under Magpul's \"max overall length\" for the longer lengths (the ledger keeps both, and says why).","Its height is read on Magpul's studio photos of the 7- and the 9-slot (the top's foreshortening for the camera's elevation, the band below it for the side); for this length it is that reading or an assumption that says so in the ledger.","Each end slopes from where its top's flat ends down to a short upright face at the mounting face, along a quarter ellipse (the photos show a rounded slope, how round isn't read), and its corners are cut off in plan at the read slant; the M moulded on one end's slope isn't drawn.","Each screw hole goes straight through, in a round recess (a counterbore with a flat floor at an assumed height, its walls upright) that cuts into the slot it is in and the lands either side, as the photos from above show it. The screws' heads are domes on the recess's floor, their socket not drawn; their heads are drawn in its two holes.","The underside is drawn flat. On the part it is a rim round a pocket, with the cammed seats round each hole and one rectangular recoil lug between the holes, which stand into the hand guard's slots (Magpul's underside photos); the cammed steel T-nuts under the hand guard's face aren't drawn either.","Its weight is worked out: the model's polymer volume times a nylon's density (std.density.polymer), the screws' heads apart. Magpul states none."],"ledger":["magpul-mlok-polymer-rail-section-5-slot.length","magpul-mlok-polymer-rail-section-5-slot.height","magpul-mlok-polymer-rail-section-5-slot.width","magpul-mlok-polymer-rail-section-5-slot.rail_slot0_x","magpul-mlok-polymer-rail-section-5-slot.lug_x","magpul-mlok-polymer-rail-section-5-slot.neck_top_below_top","magpul-mlok-polymer-rail-section-5-slot.neck_foot_above_face","magpul-mlok-polymer-rail-section-5-slot.end_bevel_length","magpul-mlok-polymer-rail-section-5-slot.end_corner_chamfer","magpul-mlok-polymer-rail-section-5-slot.counterbore_diameter","magpul-mlok-polymer-rail-section-5-slot.screw_head_diameter"]},"profiles":{},"gaps":[{"what":"Magpul's own height, width and weight for it","need":"A specification table or a drawing from Magpul; a seller's measured figures; or a level side view or end view of it with a scale (its own rail slots in frame)"},{"what":"Where its T-nuts sit in an M-LOK slot, and how far they and its recoil lugs reach inside (reach_inside)","need":"Magpul's instruction for the rail sections, or a side view of one fitted to a hand guard with the slots in frame"},{"what":"The underside's pocket, its rim and its lugs","need":"A square view of its underside with a scale; drawn flat meanwhile"}]},"magpul-mlok-polymer-rail-section-7-slot":{"id":"magpul-mlok-polymer-rail-section-7-slot","name":"M-LOK® Polymer Rail, 7 Slots","manufacturer":"Magpul","sku":"MAG591","url":"https://magpul.com/m-lokpolymerrailsection-7slots.html","category":"rail_section","description":"A 7-slot Picatinny rail in Magpul's polymer that bolts straight to a hand guard's M-LOK slots, for a light, a grip or another rail-mounted accessory. Magpul: \"Our polymer rail segment attaches to any M-LOK interface for a 7-slot Picatinny mount for lights, vertical grips, or other 1913 rail compatible accessories.\" It has a screw hole in each end slot, six pitches apart (60 mm: a T-nut in the rear half of one slot and the front half of the next), cammed T-nuts and recoil lugs under it, and bevelled ends. Black only (MAG591-BLK). NSN 1005-01-665-9435.","weight":"magpul-mlok-polymer-rail-section-7-slot.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"lug":{"origin":["{.lug_x}",0,0],"note":"The centre of the M-LOK slot its rear T-nut is in, on its mounting face: what an M-LOK position places. Its rear screw hole is at the centre of its rail slot {.rear_hole_slot}, and its T-nut half the M-LOK interval behind this point, in the rear half of the slot (which half isn't published: the ledger's lug_x says so). Rail section frame: origin at its rear end on the mounting face, +x toward the muzzle, +y away from the face."},"top_rail":{"origin":["{.rail_slot0_x}","{.height}",0],"note":"The rearmost rail slot's centre on the rail's top: what a clamp's position places, a slot further forward for each index."}},"interfaces":{"mlok":{"type":"mlok","role":"accessory","anchor":"lug","params":{"lugs":"={.lugs}","reach_inside":"={.reach_inside}"},"flips":true,"note":"Two M-LOK slots: its T-nuts 60 mm apart, one in the rear half of a slot and one in the front half of the next, with its two recoil lugs between them. Magpul's sheet: \"All hardware necessary for attachment directly to M-LOK Slots on either aluminum or polymer hand guards and forends is included.\" How far its nuts and lugs reach inside isn't published."},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}"},"flips":false,"note":"What clamps to a Picatinny rail is mounted here (D72: a mount that carries others). Magpul: \"for lights, vertical grips, or other 1913 rail compatible accessories\"; its sheet: \"various 1913 Picatinny spec rail-mounted accessories such as lights, vertical grips, etc.\" Its slots are on the standard's pitch, centred on its length."}},"materials":{"body":{"label":"Rail section","finish":"polymer","recolorable":true,"color":"magpul-black","sheen":"matte","options":{"black":{"label":"Black","finish":"polymer","color":"magpul-black","sheen":"matte","sku":"MAG591-BLK","source":"https://magpul.com/m-lokpolymerrailsection-7slots.html"}},"default":"black","note":"Magpul's polymer (its sheet: \"Injection molded from a proprietary reinforced composite for enhanced strength and durability while remaining lightweight\"; its page: \"Constructed of Magpul's light, durable polymer\"), in black, the one colour Magpul sells it in (its page's one variant, MAG591_RET_BLK_; the sheet's colour line, \"BLK\"), as matched on the MOE SL (magpul-black). One moulding: the sheet's and the page's photos have it one black all over. No other colour of any of the five lengths is sold (Magpul's pages and every seller's read)."},"screws":{"label":"Screws","finish":"steel","recolorable":false,"color":"placeholder-black","note":"Its two screws' heads in their recesses: black socket button heads in every photo of the part fitted (Magpul's), and in its photos of the hardware under the 5- and 7-slot sections. Black steel in its one colourway."}},"components":{},"geometry":{"model":"magpul-mlok-polymer-rail-section-7-slot.glb","components":{},"approximations":["Its section is the standard's rail head (MIL-STD-1913's Figure 1 from the ledger, lib.rail_head), its lower faces carried on at 45 degrees to a neck 0.2 in under the rail's top (assumed: no view along the rail is on file, and a clamp's jaws need room there), the neck upright down to a shoulder a little over the mounting face (the 5-slot's underside photo reads 0.055 in; assumed on the others), and below it the body as wide as its outline from above, straight sided; its rail slots at the standard's width, depth and pitch, centred on its length (as its own photos have them).","Its length is read on Magpul's own photos by its rail slots at the standard's pitch, 0.12 to 0.18 in under Magpul's \"max overall length\" for the longer lengths (the ledger keeps both, and says why).","Its height is read on Magpul's studio photos of the 7- and the 9-slot (the top's foreshortening for the camera's elevation, the band below it for the side); for this length it is that reading or an assumption that says so in the ledger.","Each end slopes from where its top's flat ends down to a short upright face at the mounting face, along a quarter ellipse (the photos show a rounded slope, how round isn't read), and its corners are cut off in plan at the read slant; the M moulded on one end's slope isn't drawn.","Each screw hole goes straight through, in a round recess (a counterbore with a flat floor at an assumed height, its walls upright) that cuts into the slot it is in and the lands either side, as the photos from above show it. The screws' heads are domes on the recess's floor, their socket not drawn; their heads are drawn in its two holes.","The underside is drawn flat. On the part it is a rim round a pocket, with the cammed seats round each hole and two rectangular recoil lugs between the holes, which stand into the hand guard's slots (Magpul's underside photos); the cammed steel T-nuts under the hand guard's face aren't drawn either.","Its weight is worked out: the model's polymer volume times a nylon's density (std.density.polymer), the screws' heads apart. Magpul states none."],"ledger":["magpul-mlok-polymer-rail-section-7-slot.length","magpul-mlok-polymer-rail-section-7-slot.height","magpul-mlok-polymer-rail-section-7-slot.width","magpul-mlok-polymer-rail-section-7-slot.rail_slot0_x","magpul-mlok-polymer-rail-section-7-slot.lug_x","magpul-mlok-polymer-rail-section-7-slot.neck_top_below_top","magpul-mlok-polymer-rail-section-7-slot.neck_foot_above_face","magpul-mlok-polymer-rail-section-7-slot.end_bevel_length","magpul-mlok-polymer-rail-section-7-slot.end_corner_chamfer","magpul-mlok-polymer-rail-section-7-slot.counterbore_diameter","magpul-mlok-polymer-rail-section-7-slot.screw_head_diameter"]},"profiles":{},"gaps":[{"what":"Magpul's own height, width and weight for it","need":"A specification table or a drawing from Magpul; a seller's measured figures; or a level side view or end view of it with a scale (its own rail slots in frame)"},{"what":"Where its T-nuts sit in an M-LOK slot, and how far they and its recoil lugs reach inside (reach_inside)","need":"Magpul's instruction for the rail sections, or a side view of one fitted to a hand guard with the slots in frame"},{"what":"The underside's pocket, its rim and its lugs","need":"A square view of its underside with a scale; drawn flat meanwhile"}]},"magpul-mlok-polymer-rail-section-9-slot":{"id":"magpul-mlok-polymer-rail-section-9-slot","name":"M-LOK® Polymer Rail, 9 Slots","manufacturer":"Magpul","sku":"MAG592","url":"https://magpul.com/m-lokpolymerrailsection-9slots.html","category":"rail_section","description":"A 9-slot Picatinny rail in Magpul's polymer that bolts straight to a hand guard's M-LOK slots, for a light, a grip or another rail-mounted accessory. Magpul: \"Our polymer rail segment attaches to any M-LOK interface for a 9-slot Picatinny mount for lights, vertical grips, or other 1913 rail compatible accessories.\" It has three screw holes, in the first, the fifth and the ninth slots, four pitches (40 mm) apart, cammed T-nuts and recoil lugs under it, and bevelled ends. Black only (MAG592-BLK). This length isn't on Magpul's information sheet for the others, and its page prints no NSN.","weight":"magpul-mlok-polymer-rail-section-9-slot.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"lug":{"origin":["{.lug_x}",0,0],"note":"The centre of the M-LOK slot its rear T-nut is in, on its mounting face: what an M-LOK position places. Its rear screw hole is at the centre of its rail slot {.rear_hole_slot}, and its T-nut half the M-LOK interval behind this point, in the rear half of the slot (which half isn't published: the ledger's lug_x says so). Rail section frame: origin at its rear end on the mounting face, +x toward the muzzle, +y away from the face."},"top_rail":{"origin":["{.rail_slot0_x}","{.height}",0],"note":"The rearmost rail slot's centre on the rail's top: what a clamp's position places, a slot further forward for each index."}},"interfaces":{"mlok":{"type":"mlok","role":"accessory","anchor":"lug","params":{"lugs":"={.lugs}","reach_inside":"={.reach_inside}"},"flips":true,"note":"Three M-LOK slots, with the screws in its end holes (80 mm apart): a T-nut in the rear half of one slot and one in the rear half of the slot two on. Magpul's sheet: \"All hardware necessary for attachment directly to M-LOK Slots on either aluminum or polymer hand guards and forends is included.\" How far its nuts and lugs reach inside isn't published."},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}"},"flips":false,"note":"What clamps to a Picatinny rail is mounted here (D72: a mount that carries others). Magpul: \"for lights, vertical grips, or other 1913 rail compatible accessories\"; its sheet: \"various 1913 Picatinny spec rail-mounted accessories such as lights, vertical grips, etc.\" Its slots are on the standard's pitch, centred on its length."}},"materials":{"body":{"label":"Rail section","finish":"polymer","recolorable":true,"color":"magpul-black","sheen":"matte","options":{"black":{"label":"Black","finish":"polymer","color":"magpul-black","sheen":"matte","sku":"MAG592-BLK","source":"https://magpul.com/m-lokpolymerrailsection-9slots.html"}},"default":"black","note":"Magpul's polymer (its sheet: \"Injection molded from a proprietary reinforced composite for enhanced strength and durability while remaining lightweight\"; its page: \"Constructed of Magpul's light, durable polymer\"), in black, the one colour Magpul sells it in (its page's one variant, MAG592_RET_BLK_; the sheet's colour line, \"BLK\"), as matched on the MOE SL (magpul-black). One moulding: the sheet's and the page's photos have it one black all over. No other colour of any of the five lengths is sold (Magpul's pages and every seller's read)."},"screws":{"label":"Screws","finish":"steel","recolorable":false,"color":"placeholder-black","note":"Its two screws' heads in their recesses: black socket button heads in every photo of the part fitted (Magpul's), and in its photos of the hardware under the 5- and 7-slot sections. Black steel in its one colourway."}},"components":{},"geometry":{"model":"magpul-mlok-polymer-rail-section-9-slot.glb","components":{},"approximations":["Its section is the standard's rail head (MIL-STD-1913's Figure 1 from the ledger, lib.rail_head), its lower faces carried on at 45 degrees to a neck 0.2 in under the rail's top (assumed: no view along the rail is on file, and a clamp's jaws need room there), the neck upright down to a shoulder a little over the mounting face (the 5-slot's underside photo reads 0.055 in; assumed on the others), and below it the body as wide as its outline from above, straight sided; its rail slots at the standard's width, depth and pitch, centred on its length (as its own photos have them).","Its length is read on Magpul's own photos by its rail slots at the standard's pitch, 0.12 to 0.18 in under Magpul's \"max overall length\" for the longer lengths (the ledger keeps both, and says why).","Its height is read on Magpul's studio photos of the 7- and the 9-slot (the top's foreshortening for the camera's elevation, the band below it for the side); for this length it is that reading or an assumption that says so in the ledger.","Each end slopes from where its top's flat ends down to a short upright face at the mounting face, along a quarter ellipse (the photos show a rounded slope, how round isn't read), and its corners are cut off in plan at the read slant; the M moulded on one end's slope isn't drawn.","Each screw hole goes straight through, in a round recess (a counterbore with a flat floor at an assumed height, its walls upright) that cuts into the slot it is in and the lands either side, as the photos from above show it. The screws' heads are domes on the recess's floor, their socket not drawn; their heads are drawn in its two end holes (the middle one is drawn empty).","The underside is drawn flat. On the part it is a rim round a pocket, with the cammed seats round each hole and rectangular recoil lugs between the holes, which stand into the hand guard's slots (Magpul's underside photos); the cammed steel T-nuts under the hand guard's face aren't drawn either.","Its weight is worked out: the model's polymer volume times a nylon's density (std.density.polymer), the screws' heads apart. Magpul states none."],"ledger":["magpul-mlok-polymer-rail-section-9-slot.length","magpul-mlok-polymer-rail-section-9-slot.height","magpul-mlok-polymer-rail-section-9-slot.width","magpul-mlok-polymer-rail-section-9-slot.rail_slot0_x","magpul-mlok-polymer-rail-section-9-slot.lug_x","magpul-mlok-polymer-rail-section-9-slot.neck_top_below_top","magpul-mlok-polymer-rail-section-9-slot.neck_foot_above_face","magpul-mlok-polymer-rail-section-9-slot.end_bevel_length","magpul-mlok-polymer-rail-section-9-slot.end_corner_chamfer","magpul-mlok-polymer-rail-section-9-slot.counterbore_diameter","magpul-mlok-polymer-rail-section-9-slot.screw_head_diameter"]},"profiles":{},"gaps":[{"what":"Magpul's own height, width and weight for it","need":"A specification table or a drawing from Magpul; a seller's measured figures; or a level side view or end view of it with a scale (its own rail slots in frame)"},{"what":"Where its T-nuts sit in an M-LOK slot, and how far they and its recoil lugs reach inside (reach_inside)","need":"Magpul's instruction for the rail sections, or a side view of one fitted to a hand guard with the slots in frame"},{"what":"The underside's pocket, its rim and its lugs","need":"A square view of its underside with a scale; drawn flat meanwhile"},{"what":"Which two of its three holes its two screws go in","need":"Magpul's word on the \"intermediate spacing option\"; the model has them in the end holes"}]},"magpul-mlok-qd-sling-mount":{"id":"magpul-mlok-qd-sling-mount","name":"M-LOK QD Sling Mount","manufacturer":"Magpul","sku":"MAG606","url":"https://magpul.com/m-lok-qd-sling-mount.html","category":"sling_mount","description":"Magpul's M-LOK QD Sling Mount: a low steel mount for a push-button QD swivel, on any M-LOK slot. \"Anti-rotation design stops sling from twisting and tangling\"; \"Accepts any push-button QD swivel as well as the Magpul QDM\". Black. \"Includes mounting hardware\".","weight":"magpul-mlok-qd-sling-mount.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"lug":{"origin":["{.lug_x} + {std.mlok.interval} / 2",0,0],"note":"The middle of its two screws on the mounting face (each has its lug and T-nut round it; they are the M-LOK interval apart, which is how the patent's scale is set): what an M-LOK position places. Since 2026-10-05 the middle of the two, not the rear one: a slot's position is its centre, and two nuts the M-LOK interval apart go one in each half of it (the rear nut on the centre put the front one 4 mm past the slot's end, over the web). The part frame's origin is the part's rear end on that face."}},"interfaces":{"mlok":{"type":"mlok","role":"accessory","anchor":"lug","params":{"lugs":"={.lugs}","reach_inside":"={.reach_inside}"},"flips":true,"note":"One slot: its two screws are the M-LOK interval apart and the mount is 33.6 mm long, a slot's 32 mm and a little (the patent's plan), and Magpul's sheet draws it over one slot with a T-nut over each end of it. How far the nuts reach inside isn't published."}},"materials":{"body":{"label":"Sling mount","finish":"nitride","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"nitride","color":"placeholder-black","sku":"MAG606-BLK","source":"https://magpul.com/m-lok-qd-sling-mount.html"}},"default":"black","note":"Steel, by the maker's page as it is today: \"QPQ salt bath nitrided steel for the Mount\", \"Precision cast steel with QPQ salt bath nitrided finish\" (a banner on the same page says \"Machined from\"). The mount was aluminum before: Magpul's 2018 installation sheet is subtitled \"Aluminum QD Sling Mount for M-LOK Compatible Systems\", and Wing Tactical, Scheels, Sportsman's Warehouse, Right To Bear, Alexander's, Rifle Supply, Dirty Bird and AR15Discounts still say \"Mil-Spec anodized aluminum\"; Mile High says \"Now made with heavy-duty QPQ treated steel!\". One colour, black (MAG606-BLK: Magpul's NSN line; its page has Black alone under Color, MAG606_RET_BLK_ in its data). Drawn as black nitride, the maker's finish for the mount; a nitride black isn't fitted to a photo (its brightness there is reflection), so the colour is the placeholder black. The whole mount is one piece: the lozenge, the socket's ring and its bore."},"screws":{"label":"Screws","finish":"steel","recolorable":false,"color":"placeholder-black","note":"Its two socket-head cap screws (Magpul's sheet: \"Secure M-LOK Screws using a 5/32” hex wrench\"), with knurled heads: black in Magpul's feature photo _02, and their faces a lighter grey than the mount in its gallery _05 and feature _04, where the light is on them: a smoother, more metallic black than the mount's nitride, by the look. What coats them isn't stated: drawn as dark steel in the placeholder black. The T-nuts are inside the hand guard and aren't drawn."}},"components":{},"geometry":{"model":"magpul-mlok-qd-sling-mount.glb","components":{},"approximations":["Drawn as Magpul's design patent draws it (US D746,404 S): its outer surface turned about the socket's axis, to the height the lozenge wall's top edge has at each radius in FIG. 5 (both ears give one curve within 0.001 in), cut to FIG. 3's lozenge, with the bore, its lead-in, the two screw holes and their pockets where FIG. 3 draws them and the pockets as deep as FIG. 2 shows. The model's own silhouettes are FIG. 5's and FIG. 6's within 0.003 in.","The patent's scale is its own two screw holes taken as the M-LOK interval (20 mm) apart: 1.32 in long, 0.60 wide and 0.35 off the handguard, which are Magpul's 1.3, 0.6 and 0.4 to the one decimal it prints. If Magpul's 0.4 is the truer figure, the mount stands up to 0.05 in further off the handguard than drawn.","The patent was filed in 2014, when the mount was aluminum; Magpul now sells it in steel. No page says whether the shape changed with the metal, and the two weights on file (0.62 oz in steel, 0.5 oz in aluminum, each with its hardware) are closer than this one shape in the two metals would be: today's mount has less metal in it somewhere than this shape (a relief under it wouldn't show in any photo on file).","The lozenge is made the same end for end and side for side (the patent: its opposite views mirror each other) and its outline smoothed over 0.02 in; the bore's lead-in is cut at 45 degrees; edges broken at 0.004 in.","The two screws are drawn (2026-10-06) as plain socket heads on the pockets' seats: as wide as Magpul's gallery photo _05 has them (0.27 in in a pocket of 0.32) and their tops 0.235 in off the mounting face, a rough reading of feature _02 (± 0.03: the head's knurled wall shows above its pocket's far rim and its face is well below the ring's), with the 5/32 in hex Magpul's sheet names, drawn as deep as it is wide. The knurl isn't drawn.","Not drawn: the screws' T-nuts; the lugs under the mounting face; and what limits a swivel's turning inside the bore (broken lines in the patent, unclaimed)."],"ledger":["magpul-mlok-qd-sling-mount.length","magpul-mlok-qd-sling-mount.height","magpul-mlok-qd-sling-mount.width","magpul-mlok-qd-sling-mount.lug_x","magpul-mlok-qd-sling-mount.screw_seat_height","magpul-mlok-qd-sling-mount.screw_head_diameter","magpul-mlok-qd-sling-mount.screw_head_top","magpul-mlok-qd-sling-mount.screw_hex"]},"profiles":{"plan":{"plane":"xz","origin":"the mount's rear end, on its centre line","offset":{},"points":[[0,0.056],[0,-0.053],[0.005,-0.091],[0.024,-0.131],[0.051,-0.163],[0.074,-0.179],[0.097,-0.19],[0.119,-0.197],[0.121,-0.195],[0.125,-0.198],[0.257,-0.209],[0.275,-0.214],[0.28,-0.212],[0.331,-0.219],[0.384,-0.222],[0.431,-0.229],[0.458,-0.235],[0.492,-0.249],[0.519,-0.266],[0.546,-0.276],[0.556,-0.283],[0.559,-0.282],[0.609,-0.296],[0.674,-0.3],[0.722,-0.294],[0.746,-0.287],[0.75,-0.289],[0.756,-0.283],[0.77,-0.282],[0.776,-0.276],[0.805,-0.264],[0.843,-0.242],[0.89,-0.229],[1.011,-0.215],[1.028,-0.216],[1.035,-0.213],[1.089,-0.209],[1.109,-0.205],[1.163,-0.203],[1.169,-0.199],[1.176,-0.203],[1.183,-0.198],[1.205,-0.196],[1.235,-0.186],[1.26,-0.171],[1.29,-0.143],[1.313,-0.098],[1.321,-0.054],[1.321,0.056],[1.314,0.095],[1.296,0.132],[1.261,0.17],[1.227,0.189],[1.224,0.188],[1.217,0.193],[1.19,0.199],[1.149,0.201],[1.143,0.206],[1.137,0.203],[1.113,0.204],[1.075,0.209],[1.068,0.213],[1.064,0.21],[1.026,0.215],[1.009,0.215],[1.004,0.217],[0.886,0.229],[0.837,0.245],[0.783,0.275],[0.759,0.282],[0.751,0.287],[0.749,0.285],[0.742,0.29],[0.698,0.298],[0.644,0.301],[0.617,0.296],[0.614,0.297],[0.569,0.287],[0.553,0.279],[0.54,0.276],[0.485,0.245],[0.482,0.247],[0.475,0.242],[0.435,0.229],[0.429,0.232],[0.412,0.226],[0.401,0.226],[0.375,0.221],[0.371,0.223],[0.325,0.217],[0.32,0.22],[0.314,0.215],[0.307,0.219],[0.301,0.215],[0.266,0.213],[0.24,0.208],[0.236,0.21],[0.179,0.202],[0.172,0.204],[0.167,0.201],[0.132,0.199],[0.081,0.183],[0.053,0.164],[0.028,0.137],[0.005,0.091]],"features":{"screw_holes":[[[0.376,-0.014],[0.368,-0.042],[0.354,-0.067],[0.334,-0.087],[0.309,-0.101],[0.281,-0.109],[0.253,-0.109],[0.225,-0.101],[0.2,-0.087],[0.18,-0.067],[0.166,-0.042],[0.158,-0.014],[0.158,0.014],[0.166,0.042],[0.18,0.067],[0.2,0.087],[0.225,0.101],[0.253,0.109],[0.281,0.109],[0.309,0.101],[0.334,0.087],[0.354,0.067],[0.368,0.042],[0.376,0.014]],[[1.163,-0.014],[1.156,-0.042],[1.141,-0.067],[1.121,-0.087],[1.096,-0.101],[1.069,-0.109],[1.04,-0.109],[1.013,-0.101],[0.988,-0.087],[0.968,-0.067],[0.953,-0.042],[0.946,-0.014],[0.946,0.014],[0.953,0.042],[0.968,0.067],[0.988,0.087],[1.013,0.101],[1.04,0.109],[1.069,0.109],[1.096,0.101],[1.121,0.087],[1.141,0.067],[1.156,0.042],[1.163,0.014]]],"counterbores":[[[0.427,-0.016],[0.421,-0.047],[0.409,-0.076],[0.391,-0.102],[0.369,-0.124],[0.343,-0.142],[0.314,-0.154],[0.283,-0.16],[0.251,-0.16],[0.22,-0.154],[0.191,-0.142],[0.165,-0.124],[0.143,-0.102],[0.125,-0.076],[0.113,-0.047],[0.107,-0.016],[0.107,0.016],[0.113,0.047],[0.125,0.076],[0.143,0.102],[0.165,0.124],[0.191,0.142],[0.22,0.154],[0.251,0.16],[0.283,0.16],[0.314,0.154],[0.343,0.142],[0.369,0.124],[0.391,0.102],[0.409,0.076],[0.421,0.047],[0.427,0.016]],[[1.214,-0.016],[1.208,-0.047],[1.196,-0.076],[1.179,-0.102],[1.156,-0.124],[1.13,-0.142],[1.101,-0.154],[1.07,-0.16],[1.039,-0.16],[1.008,-0.154],[0.978,-0.142],[0.952,-0.124],[0.93,-0.102],[0.912,-0.076],[0.9,-0.047],[0.894,-0.016],[0.894,0.016],[0.9,0.047],[0.912,0.076],[0.93,0.102],[0.952,0.124],[0.978,0.142],[1.008,0.154],[1.039,0.16],[1.07,0.16],[1.101,0.154],[1.13,0.142],[1.156,0.124],[1.179,0.102],[1.196,0.076],[1.208,0.047],[1.214,0.016]]],"bore":[[[0.847,-0.018],[0.839,-0.054],[0.825,-0.088],[0.805,-0.118],[0.779,-0.144],[0.749,-0.165],[0.715,-0.179],[0.679,-0.186],[0.642,-0.186],[0.606,-0.179],[0.573,-0.165],[0.542,-0.144],[0.516,-0.118],[0.496,-0.088],[0.482,-0.054],[0.475,-0.018],[0.475,0.018],[0.482,0.054],[0.496,0.088],[0.516,0.119],[0.542,0.144],[0.573,0.165],[0.606,0.179],[0.642,0.186],[0.679,0.186],[0.715,0.179],[0.749,0.165],[0.779,0.144],[0.805,0.119],[0.825,0.088],[0.839,0.054],[0.847,0.018]]],"bore_lead":[[[0.858,-0.019],[0.85,-0.057],[0.835,-0.093],[0.814,-0.126],[0.786,-0.153],[0.754,-0.175],[0.718,-0.19],[0.68,-0.197],[0.641,-0.197],[0.603,-0.19],[0.567,-0.175],[0.535,-0.153],[0.507,-0.126],[0.486,-0.093],[0.471,-0.057],[0.463,-0.019],[0.463,0.02],[0.471,0.058],[0.486,0.094],[0.507,0.126],[0.535,0.153],[0.567,0.175],[0.603,0.19],[0.641,0.197],[0.68,0.197],[0.718,0.19],[0.754,0.175],[0.786,0.153],[0.814,0.126],[0.835,0.094],[0.85,0.058],[0.858,0.02]]],"boss_face":[[[0.925,-0.021],[0.918,-0.062],[0.905,-0.101],[0.886,-0.138],[0.862,-0.172],[0.833,-0.201],[0.799,-0.226],[0.762,-0.245],[0.722,-0.258],[0.681,-0.264],[0.64,-0.264],[0.599,-0.258],[0.559,-0.245],[0.522,-0.226],[0.489,-0.201],[0.459,-0.172],[0.435,-0.138],[0.416,-0.101],[0.403,-0.062],[0.397,-0.021],[0.397,0.021],[0.403,0.062],[0.416,0.101],[0.435,0.138],[0.459,0.172],[0.489,0.201],[0.522,0.226],[0.559,0.245],[0.599,0.257],[0.64,0.264],[0.681,0.264],[0.722,0.257],[0.762,0.245],[0.799,0.226],[0.833,0.201],[0.862,0.172],[0.886,0.138],[0.905,0.101],[0.918,0.062],[0.925,0.021]]],"boss":[[[0.96,-0.024],[0.952,-0.07],[0.938,-0.115],[0.916,-0.157],[0.889,-0.195],[0.855,-0.228],[0.817,-0.256],[0.775,-0.277],[0.731,-0.292],[0.684,-0.299],[0.637,-0.299],[0.591,-0.292],[0.546,-0.277],[0.504,-0.256],[0.466,-0.228],[0.433,-0.195],[0.405,-0.157],[0.383,-0.115],[0.369,-0.07],[0.362,-0.024],[0.362,0.024],[0.369,0.07],[0.383,0.115],[0.405,0.157],[0.433,0.195],[0.466,0.228],[0.504,0.256],[0.546,0.277],[0.591,0.292],[0.637,0.299],[0.684,0.299],[0.731,0.292],[0.775,0.277],[0.817,0.256],[0.855,0.228],[0.889,0.195],[0.916,0.157],[0.938,0.115],[0.952,0.07],[0.96,0.024]]]},"scaleRefs":["magpul-mlok-qd-sling-mount.lug_x","std.mlok.interval"],"inputs":{"magpul-mlok-qd-sling-mount.lug_x":0.267,"std.mlok.interval":0.7874015748031495},"tolerance":0.002,"photo":"references/magpul-mlok-qd-sling-mount 984ec513ef51 (US D746,404 S (Magpul, 'Firearm quick detach mount for a sling'), FIG. 3 front elevation (the outer face), 300 dpi)","method":"luminance < 128, inside [440, 2060, 2120, 2845], closing ×3, holes filled, inset 2 px (half the outline's stroke); frame from the reviewed holes rear, front (1186.6 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.002 in with the extremes kept: 105 points (IoU 0.994 with the full outline); features through the same placement (screw_holes: the two screw holes: circles fitted to their strokes; counterbores: the pocket round each screw hole: the outer of its two circles, the pocket's wall; bore: the socket's bore: the heavier of its two circles; bore_lead: the bore's lead-in: the lighter circle round the bore; boss_face: the socket ring's flat face: its outer circle, where the bevel begins (each screw's pocket bites it at its end); boss: the socket's ring: the bevel's base, the circle the outline joins at its widest) (tools/trace.py)","via":"harvest","note":"Symmetric both ways. The outline is the lozenge; the dashes inside the bore are broken lines (what limits a swivel's turning: unclaimed) and aren't traced."},"side":{"plane":"xy","origin":"the mount's rear end on the mounting face","offset":{},"points":[[0,0.127],[0,0.005],[0.002,0.002],[0.034,0],[1.287,0],[1.32,0.002],[1.321,0.13],[1.22,0.173],[1.185,0.181],[1.128,0.201],[1.117,0.202],[1.098,0.21],[1.093,0.215],[1.091,0.213],[1.074,0.218],[1.041,0.234],[1.012,0.251],[0.981,0.274],[0.942,0.314],[0.914,0.354],[0.408,0.354],[0.376,0.311],[0.352,0.285],[0.311,0.253],[0.281,0.234],[0.211,0.205],[0.174,0.194],[0.171,0.195],[0.16,0.189],[0.101,0.173],[0.004,0.132]],"features":{"wall_top":[[[1.319,0.131],[1.316,0.131],[1.304,0.134],[1.292,0.137],[1.28,0.14],[1.268,0.143],[1.257,0.146],[1.245,0.151],[1.233,0.154],[1.221,0.158],[1.209,0.162],[1.198,0.166],[1.186,0.17],[1.174,0.175],[1.162,0.178],[1.151,0.184],[1.139,0.188],[1.127,0.192],[1.115,0.196],[1.103,0.2],[1.092,0.204],[1.08,0.208],[1.068,0.212],[1.056,0.216],[1.044,0.221],[1.033,0.225],[1.021,0.231],[1.009,0.236],[0.997,0.241],[0.985,0.246],[0.974,0.252],[0.962,0.259],[0.95,0.264],[0.938,0.271],[0.927,0.277],[0.915,0.282],[0.903,0.289],[0.891,0.296],[0.879,0.301],[0.867,0.307],[0.852,0.312],[0.841,0.315],[0.833,0.316],[0.812,0.319]],[[0.001,0.132],[0.005,0.132],[0.016,0.133],[0.028,0.136],[0.04,0.139],[0.052,0.143],[0.064,0.146],[0.075,0.15],[0.087,0.154],[0.099,0.158],[0.111,0.162],[0.123,0.166],[0.134,0.17],[0.146,0.175],[0.158,0.178],[0.17,0.183],[0.181,0.188],[0.193,0.192],[0.205,0.196],[0.217,0.2],[0.229,0.205],[0.24,0.208],[0.252,0.212],[0.264,0.217],[0.276,0.221],[0.288,0.226],[0.299,0.231],[0.311,0.236],[0.323,0.241],[0.335,0.247],[0.346,0.252],[0.358,0.258],[0.37,0.264],[0.382,0.27],[0.394,0.277],[0.405,0.281],[0.418,0.289],[0.431,0.296],[0.443,0.302],[0.455,0.308],[0.468,0.312],[0.479,0.315],[0.49,0.316],[0.509,0.319]]]},"scaleRefs":["magpul-mlok-qd-sling-mount.length"],"inputs":{"magpul-mlok-qd-sling-mount.length":1.321},"tolerance":0.002,"photo":"references/magpul-mlok-qd-sling-mount 687aa3642788 (US D746,404 S (Magpul, 'Firearm quick detach mount for a sling'), FIG. 5 top plan view (the mount from its side, the mounting face on top), 300 dpi)","method":"luminance < 128, inside [420, 1568, 2100, 2030], closing ×3, holes filled, inset 2 px (half the outline's stroke); rotated +180.0° as declared; scale from magpul-mlok-qd-sling-mount.length = 1.321 in (x-extent 1569 px → 1187.7 px/in); origin at x min, y min of the outline; Douglas-Peucker at 0.002 in with the extremes kept: 31 points (IoU 0.997 with the full outline); features through the same placement (wall_top: the lozenge wall's top edge down each ear (the thinner curve), from the end wall's top corner to the ring) (tools/trace.py)","via":"harvest","note":"Symmetric end for end. The silhouette's curve down each ear is what is left of a turned surface once the screws' pockets are cut (the model's account, checked on FIG. 2, FIG. 5 and FIG. 6); the lugs under the mounting face are broken lines and aren't in it."},"front":{"plane":"zy","origin":"the mounting face, on the centre line","offset":{},"points":[[-0.3,0.319],[-0.3,0.002],[0,0.001],[0.13,0.003],[0.135,0],[0.137,0.003],[0.3,0.002],[0.3,0.319],[0.265,0.354],[0.197,0.354],[-0.267,0.353]],"scaleRefs":["magpul-mlok-qd-sling-mount.width","magpul-mlok-qd-sling-mount.height"],"inputs":{"magpul-mlok-qd-sling-mount.height":0.354,"magpul-mlok-qd-sling-mount.width":0.6},"tolerance":0.002,"photo":"references/magpul-mlok-qd-sling-mount 687aa3642788 (US D746,404 S (Magpul, 'Firearm quick detach mount for a sling'), FIG. 6 right side elevation (the mount from its end), 300 dpi)","method":"luminance < 128, inside [940, 2240, 1419, 3040], closing ×3, holes filled, inset 2 px (half the outline's stroke); rotated -90.0° as declared; scale from magpul-mlok-qd-sling-mount.width = 0.6 in (x-extent 713 px → 1188.3 px/in) and magpul-mlok-qd-sling-mount.height = 0.354 in (y-extent 421 px → 1189.3 px/in), which agree within 0.1%; mean 1188.8 px/in; origin at x center, y min of the outline; Douglas-Peucker at 0.002 in with the extremes kept: 11 points (IoU 0.997 with the full outline) (tools/trace.py)","via":"harvest","note":"Symmetric. The socket's ring from its end: its bevelled face across the whole width. The curves inside the outline (the wall's top edge and a pocket's rim, seen from the end) aren't traced: the model is checked against them."}},"gaps":[{"what":"How far the T-nuts reach inside the handguard (reach_inside)","need":"A Magpul figure or drawing of the M-LOK T-nut's height"},{"what":"Whether the steel mount sold today has the patent's shape","need":"A straight photo of the current mount beside a scale, or a drawing: the patent is of the aluminum mount, and the weights suggest the steel one has less metal in it than this shape would. Its plan agrees where Magpul's photos show it (the screws' spacing, the ring's face)"},{"what":"The screws' size and what coats them (their heads are drawn from two photo readings, ± 0.015 and ± 0.03 in), and the T-nuts","need":"A figure for the screw's head (Magpul's sheet gives only its 5/32 in hex) or a straight photo of the mount with its hardware beside a scale"}]},"magpul-mlok-rail-cover-type-2":{"id":"magpul-mlok-rail-cover-type-2","name":"M-LOK Rail Cover Type 2","manufacturer":"Magpul","sku":"MAG603","url":"https://magpul.com/m-lok-rail-covers-type2.html","category":"rail_cover","description":"One of Magpul's M-LOK Rail Covers, Type 2: a low two-piece polymer cover with the TSP texture for one unused M-LOK slot on an aluminum handguard. Its base drops into the slot and its centre locking tab pushes down and snaps in; a pointed tool or a cartridge's tip in one of its four windows lets it go. MAG603 is the pack of six; one comes in the M-LOK Hand Stop Kit (MAG608). Black, FDE, ODG, Stealth Gray, and in the pack Modified Coyote Brown. Magpul: not for its MOE M-LOK, MOE SL or SGA forends, and it may not fit a free-float handguard with a wider, flatter profile.","weight":"magpul-mlok-rail-cover-type-2.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"lug":{"origin":["{.length} / 2",0,0],"note":"The middle of the cover on its mounting face: what an M-LOK position places. The mounting face is the flat pad under the cover's middle (mounting_flat_width, 0.61 in across), which is what bears on the handguard's M-LOK face; the wings either side hang wing_drop (0.11 in) below it, over the handguard's corners, and touch nothing on a face no wider than the pad. Its two lugs (the patent's broken lines) stand the M-LOK interval apart, one either side of this point, in the two halves of the slot. Rail cover frame: origin at the part's rear end on the mounting face, +x forward along the handguard, +y out of the face (away from the handguard: the solver turns it to the face it is on)."}},"interfaces":{"mlok":{"type":"mlok","role":"accessory","anchor":"lug","params":{"lugs":"={.lugs}","reach_inside":"={.reach_inside}","in_slot":true},"flips":false,"note":"One slot, by Magpul's own words (\"One cover fills one M-LOK slot, with six covers per package\"): at 1.560 in it is 0.015 in short of the slot pitch, so covers in neighbouring slots stand a hairline apart. How far its latches and the locking tab's legs reach inside is read off the patent's broken lines (0.21 in), not published. Where it goes, by Magpul's instruction sheet (072-0096-A): \"Covers are optimized for use at the 3, 6, 9 o’clock postions.\" What it doesn't fit, by Magpul's page: \"Not compatible with Magpul MOE® M-LOK, MOE SL®, or SGA® forends\" and \"May not fit some free-float aluminum handguards that have wider, flatter profile\"; the information sheet says why: \"they will not seat deep enough to allow the center portion to lock down\". None of that is checked here: no rule compares a handguard's face with the cover's pad."}},"materials":{"body":{"label":"Rail cover","finish":"polymer","recolorable":true,"color":"magpul-black","sheen":"matte","options":{"black":{"label":"Black","finish":"polymer","color":"magpul-black","sheen":"matte","sku":"MAG603-BLK","source":"https://www.primaryarms.com/magpul-m-lok-rail-cover-type-2-black"},"fde":{"label":"FDE","finish":"polymer","color":"magpul-fde","sheen":"matte","sku":"MAG603-FDE","source":"https://magpul.com/media/wysiwyg/GIS/MAG603_M-LOK_Type_2_Rail_Covers_GIS_01.pdf"},"odg":{"label":"ODG","finish":"polymer","color":"magpul-odg","sheen":"matte","sku":"MAG603-ODG","source":"https://magpul.com/media/wysiwyg/GIS/MAG603_M-LOK_Type_2_Rail_Covers_GIS_01.pdf"},"sgy":{"label":"Stealth Gray","finish":"polymer","color":"magpul-stealth-gray","sheen":"matte","sku":"MAG603-GRY","source":"https://magpul.com/media/wysiwyg/GIS/MAG603_M-LOK_Type_2_Rail_Covers_GIS_01.pdf"},"mcb":{"label":"Modified Coyote Brown","finish":"polymer","color":"magpul-mcb","sheen":"matte","source":"https://magpul.com/m-lok-rail-covers-type2.html"}},"default":"black","note":"Magpul's polymer with the TSP texture. Five colours on Magpul's page today (read 2026-10-06 on the harvested copy: Black, Flat Dark Earth, Modified Coyote Brown, Olive Drab Green, Stealth Gray; \"NOW IN MCB!\"); four of them Magpul's colours as matched on the MOE SL, and the fifth matched on this cover against the FDE one in Magpul's own gallery (data/colors/magpul-accessories.yaml). The numbers are the pack of six's: Magpul's information sheet prints \"MAG603\" over \"BLK, FDE, GRY, ODG\", Primary Arms' page for the black pack prints MAG603-BLK, and Magpul's own page prints MAG603 and the swatches. For Modified Coyote Brown no page on file prints a number in that form (Magpul's page data has MAG603_RET_MCB_, as it has MAG603_RET_BLK_ for the black): the option has none. The hand stop kit (MAG608), which holds one cover, isn't sold in that colour. The base and the locking tab are two mouldings, the same colour in a pack (Magpul's gallery _02 in FDE, ODG, gray and MCB), and Magpul shows them mixed (\"mix and match colors as desired\"): one slot here, one colour. No hardware: nothing on it is metal."}},"components":{},"geometry":{"model":"magpul-mlok-rail-cover-type-2.glb","components":{},"approximations":["Drawn as Magpul's design patent draws the set assembled (US D755,332 S): the end elevation (FIG. 16) run the cover's length and cut to the side elevation (FIG. 15) and the plan (FIG. 17). The section is made the same left and right and redrawn where the drawing is one curve or one line: an arc over the crown from its top to the locking tab's edges, each wing's ridge and slope as two lines with an arc of 0.22 in between them, each wing's underside a line (within 0.002 in of the tracing each); the wings' tips, the beads and the pad's edges are as traced.","The patent's scale is the cover's length as the user's gallery image of the kit installed has it: one slot pitch less the 0.015 in between two covers in a row (1.560 in). At that scale the cover stands 0.136 in off the face (Magpul: \"just over 1/8 in\"), is 1.039 in wide (1.036 in the image), and its lugs read 0.270 in across for a 0.276 in slot and the M-LOK interval apart.","It bears on the flat pad under its middle (0.61 in across); each wing's tip hangs 0.11 in below that face. On a handguard whose M-LOK face is wider than the pad the wings are drawn through its corners, and nothing says so (Magpul's 'wider, flatter profile').","The seam down each side of the locking tab is the slot the patent's two lines leave between the tab's side and the channel's wall (0.005 in at the top), stopping its own width short of the channel's floor.","Each of the four windows is a pocket from the seam out over the wing: its floor as wide as the plan draws it (0.10 in) and one arc, level at the channel's floor under the tab's edge and running out on the wing's slope where the plan ends it (which is where the side elevation ends it too, within 0.002 in); its sides ruled from the floor's edge to the opening's edge on the wing (0.15 in apart), closing in over the last 0.02 in where the pocket runs out. The floor between its two sourced ends is assumed to be that one arc.","Not drawn: the two lugs, their latches and the locking tab's legs under the pad (the patent's broken lines; they stand in the slot and inside the handguard); the base's stepped end under each end of the tab (the ends are the side elevation's); the part number moulded in the channel under the tab. Edges broken at 0.003 in. The TSP texture is the finish, not geometry."],"ledger":["magpul-mlok-rail-cover-type-2.length","magpul-mlok-rail-cover-type-2.height","magpul-mlok-rail-cover-type-2.width","magpul-mlok-rail-cover-type-2.wing_drop","magpul-mlok-rail-cover-type-2.mounting_flat_width"]},"profiles":{"plan":{"plane":"xz","origin":"the cover's rear end, on its centre line","offset":{},"points":[[0,-0.386],[0.001,-0.447],[0.006,-0.46],[0.018,-0.472],[0.077,-0.506],[0.085,-0.507],[0.092,-0.513],[0.113,-0.519],[1.437,-0.52],[1.476,-0.511],[1.508,-0.491],[1.528,-0.482],[1.551,-0.465],[1.557,-0.457],[1.559,-0.447],[1.56,-0.165],[1.556,-0.144],[1.556,0.148],[1.56,0.162],[1.56,0.434],[1.555,0.46],[1.544,0.472],[1.472,0.513],[1.453,0.52],[0.105,0.52],[0.071,0.505],[0.019,0.475],[0.007,0.464],[0.001,0.451],[0.004,-0.144],[0.001,-0.152]],"features":{"tab":[[[0.001,0.229],[1.561,0.229],[1.561,-0.226],[0.001,-0.226]]],"windows":[[[0.313,0.439],[0.459,0.439],[0.459,0.229],[0.313,0.229]],[[1.1,0.439],[1.247,0.439],[1.247,0.229],[1.1,0.229]],[[0.313,-0.226],[0.459,-0.226],[0.459,-0.436],[0.313,-0.436]],[[1.1,-0.226],[1.247,-0.226],[1.247,-0.436],[1.1,-0.436]]],"window_floors":[[[0.337,0.439],[0.434,0.439],[0.434,0.229],[0.337,0.229]],[[1.124,0.439],[1.222,0.439],[1.222,0.229],[1.124,0.229]],[[0.337,-0.226],[0.434,-0.226],[0.434,-0.436],[0.337,-0.436]],[[1.124,-0.226],[1.222,-0.226],[1.222,-0.436],[1.124,-0.436]]]},"scaleRefs":["magpul-mlok-rail-cover-type-2.length"],"inputs":{"magpul-mlok-rail-cover-type-2.length":1.56},"tolerance":0.002,"photo":"references/magpul-mlok-rail-cover-type-2 762c1cfdade3 (US D755,332 S (Magpul, 'Slot cover set for a firearm'), FIG. 17 top plan of the set assembled, 300 dpi)","method":"luminance < 128, inside [480, 560, 2080, 1640], closing ×4, holes filled, opening after the fill 7 px ×1, inset 1 px (half the outline's stroke); scale from magpul-mlok-rail-cover-type-2.length = 1.56 in (x-extent 1501 px → 962.2 px/in); origin at x min, y center of the outline; Douglas-Peucker at 0.002 in with the extremes kept: 31 points (IoU 0.999 with the full outline); features through the same placement (tab: the locking tab's band, between its two edges (the heavy lines at v 877.5 and 1314.5); windows: each window's opening at the wing's surface: from the tab's edge out to its outer end, its two outer lines; window_floors: each window's floor: between the middles of the double line down each side) (tools/trace.py)","via":"harvest","note":"Symmetric both ways. The four corners are cut off (the wings' tips, which the side elevation shows as its rounded lower corners). The tab runs the whole length, its ends 2 to 3 px inside the wings'."},"side":{"plane":"xy","origin":"the cover's rear end on the mounting face (the pad under its middle, which this view doesn't draw: its level is the end elevation's)","offset":{},"points":[[0,0.067],[0,0.06],[0.003,0.056],[0.001,-0.061],[0.022,-0.078],[0.096,-0.108],[0.116,-0.11],[0.49,-0.111],[1.287,-0.111],[1.459,-0.109],[1.541,-0.078],[1.555,-0.067],[1.557,-0.06],[1.56,-0.039],[1.56,0.034],[1.557,0.054],[1.559,0.084],[1.556,0.088],[1.555,0.127],[1.553,0.132],[1.545,0.136],[0.024,0.136],[0.008,0.133],[0.004,0.071]],"features":{"windows":[[[0.314,0.114],[0.458,0.114],[0.458,0.017],[0.314,0.017]],[[1.101,0.114],[1.245,0.114],[1.245,0.017],[1.101,0.017]]]},"scaleRefs":["magpul-mlok-rail-cover-type-2.length"],"inputs":{"magpul-mlok-rail-cover-type-2.length":1.56},"tolerance":0.002,"photo":"references/magpul-mlok-rail-cover-type-2 cbf4bce0c094 (US D755,332 S (Magpul, 'Slot cover set for a firearm'), FIG. 15 right side elevation of the set assembled, 300 dpi)","method":"luminance < 128, inside [480, 1840, 2080, 2119], closing ×12, holes filled, opening after the fill 7 px ×1, inset 1 px (half the outline's stroke); frame from the reviewed holes rear, front (919.2 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.002 in with the extremes kept: 24 points (IoU 0.998 with the full outline); features through the same placement (windows: each window as the side elevation draws it: its opening's two sides, from its upper edge on the wing's ridge down to where its floor runs out on the wing's slope) (tools/trace.py)","via":"harvest","note":"The same end for end. Its upper edge is the locking tab's crown, its lower edge the near wing's tip, its rounded lower corners the plan's cut-off corners seen from the side; the lugs under it are broken lines and aren't in it."},"front":{"plane":"zy","origin":"the mounting face (the pad under the cover's middle), on the centre line","offset":{},"points":[[-0.519,-0.089],[-0.515,-0.105],[-0.51,-0.11],[-0.504,-0.111],[-0.453,-0.077],[-0.369,-0.015],[-0.327,0.011],[-0.305,0],[-0.143,0.001],[-0.135,-0.001],[-0.127,0.001],[0.306,0],[0.314,0.001],[0.327,0.01],[0.334,0.01],[0.499,-0.108],[0.516,-0.108],[0.519,-0.099],[0.519,-0.07],[0.513,-0.053],[0.391,0.062],[0.357,0.087],[0.321,0.104],[0.287,0.113],[0.283,0.111],[0.274,0.115],[0.261,0.114],[0.257,0.117],[0.236,0.121],[0.23,0.116],[0.218,0.123],[0.191,0.124],[0.165,0.129],[0.143,0.128],[0.092,0.135],[0.079,0.133],[0.047,0.136],[0.044,0.134],[0.04,0.136],[0.034,0.134],[0.032,0.136],[-0.032,0.136],[-0.035,0.134],[-0.041,0.136],[-0.044,0.134],[-0.048,0.136],[-0.052,0.134],[-0.108,0.134],[-0.143,0.128],[-0.166,0.129],[-0.182,0.125],[-0.218,0.123],[-0.23,0.117],[-0.237,0.121],[-0.257,0.117],[-0.261,0.114],[-0.274,0.115],[-0.322,0.104],[-0.347,0.09],[-0.35,0.091],[-0.392,0.062],[-0.513,-0.053],[-0.517,-0.062]],"features":{"tab":[[[-0.229,0.12],[-0.194,0.071],[0.194,0.071],[0.229,0.12]]],"channel":[[[-0.234,0.121],[-0.201,0.071],[0.201,0.071],[0.234,0.121]]]},"scaleRefs":["magpul-mlok-rail-cover-type-2.width"],"inputs":{"magpul-mlok-rail-cover-type-2.width":1.039},"tolerance":0.002,"photo":"references/magpul-mlok-rail-cover-type-2 cbf4bce0c094 (US D755,332 S (Magpul, 'Slot cover set for a firearm'), FIG. 16 front elevation of the set assembled, 300 dpi)","method":"luminance < 128, inside [700, 2380, 1900, 2720], 1 boxes excluded, closing ×4, holes filled, notches filled in [765, 2620, 830, 2700] (disk closing, r 10 px), notches filled in [1675, 2620, 1740, 2700] (disk closing, r 10 px), inset 1 px (half the outline's stroke); frame from the reviewed holes left, right (920.1 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.002 in with the extremes kept: 63 points (IoU 0.985 with the full outline); checks: height 0.247 ± 0.003 in vs magpul-mlok-rail-cover-type-2.section_height 0.247 ± 0.006 (provisional): agrees; features through the same placement (tab: the locking tab's section under its crown: its two sides (the inner line of each pair) and its underside; channel: the base's channel: its two walls (the outer line of each pair, from each wing's peak) and its floor) (tools/trace.py)","via":"harvest","note":"Symmetric. The crown runs in one arc over the tab and both wings' ridges; each wing turns down at a crease into a straight slope to its tip; under the middle the flat pad, a bead at each of its edges, and each wing's underside rising from the tip to the bead. The lugs and the tab's legs under the pad are broken lines and aren't in it."}},"gaps":[{"what":"A published length, width or weight for one cover","need":"Magpul states none (its page, its information sheet and its instruction sheet were read): the length is read on a picture of a row of covers, the width is the patent's at that length, the weight is a retailer's list of the hand stop kit's pieces (0.15 oz, source unstated)"},{"what":"Whether a handguard's M-LOK face takes it","need":"Each host's face width beside its slots and how its corners fall away, to hold against the cover's pad (0.61 in) and its wings (0.11 in below the pad): Magpul says it may not fit a wider, flatter profile and names no figure"},{"what":"How far it reaches inside the handguard once locked (reach_inside is the patent's broken lines: 0.21 in ± 0.02)","need":"A straight photo of a cover from its side with the tab home, lugs and legs in view, or a figure from Magpul"},{"what":"The source page of the user's image","need":"The gallery it was screenshotted from, for the manifest (the hand stop's gap too)"},{"what":"The colour Modified Coyote Brown","need":"A colour preset matched for it (Magpul's page lists it for MAG603; its information sheet doesn't)"}]},"magpul-moe-carbine":{"id":"magpul-moe-carbine","name":"MOE carbine stock, mil-spec","manufacturer":"Magpul","sku":"MAG400","category":"stock","description":"Magpul's plain A-frame carbine stock: a cheek round the tube, an open triangular frame, a 0.30 in rubber butt pad. Six positions on a mil-spec receiver extension. Magpul lists its length of pull 0.6 in shorter than the MOE SL's; seated from their photo of it on a rifle, it comes to 0.4.","weight":"magpul-moe-carbine.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"butt":{"origin":[0,0,0],"note":"The butt's plane on the tube axis: the part frame's origin. Overall length and length of pull end here."},"tube":{"origin":["{.butt_behind_pin_pos1}",0,0],"x":[-1,0,0],"note":"Stock frame: origin on the tube axis in the plane of the butt, +x forward. At position 1 this anchor sits at the takedown pin's X."}},"interfaces":{"tube":{"type":"receiver_extension","role":"stock","anchor":"tube","params":{"profile":"mil-spec"},"flips":false,"note":"MAG400 is the Mil-Spec model. Magpul's Commercial-Spec MOE (MAG401) is a longer stock with a thicker pad, not this body bored differently."}},"materials":{"body":{"label":"Stock body","finish":"polymer","recolorable":true,"color":"magpul-black","sheen":"satin","options":{"black":{"label":"Black","finish":"polymer","color":"magpul-black","sheen":"satin","sku":"MAG400-BLK","source":"https://magpul.com/moe-carbine-stock-mil-spec.html"},"fde":{"label":"FDE","finish":"polymer","color":"magpul-fde","sheen":"satin","sku":"MAG400-FDE","source":"https://magpul.com/moe-carbine-stock-mil-spec.html"},"odg":{"label":"ODG","finish":"polymer","color":"magpul-odg","sheen":"satin","sku":"MAG400-ODG","source":"https://magpul.com/moe-carbine-stock-mil-spec.html"},"sgy":{"label":"Stealth Gray","finish":"polymer","color":"magpul-stealth-gray","sheen":"satin","sku":"MAG400-GRY","source":"https://magpul.com/moe-carbine-stock-mil-spec.html"}},"default":"black","note":"Magpul's four swatches for MAG400 (Black, Flat Dark Earth, Olive Drab Green, Stealth Gray). The colours are the ones matched on the MOE SL. Its page states MAG400-BLK and MAG400-ODG (beside their NSNs); MAG400-FDE and MAG400-GRY are as Big Tex Ordnance's listing and Primary Arms' FDE page state them. In every colour the release latch is the body's colour, as drawn (Primary Arms' FDE and OD side views, Big Tex's Stealth Gray). What stays black on every colour and isn't drawn: the lock pin's head and the latch's pivot pin."},"buttpad":{"label":"Buttpad","finish":"rubber","recolorable":false,"color":"magpul-black","note":"Black rubber on every colour of stock (Primary Arms' FDE and ODG side views)."}},"components":{"body":{"label":"Stock body","material":"body"},"buttpad":{"label":"Buttpad","material":"buttpad"}},"geometry":{"model":"magpul-moe-carbine.glb","components":{},"approximations":["Visual hull of the traced side photo (Primary Arms, scaled by Magpul's 7.0 x 5.2 in, which fit it within 0.4%) and the end section from Magpul's design patent (US D600,308 S, FIG. 4, scaled by 5.2 x 1.7 in, which fit it within 0.5%): the section holds along the stock wherever the side view shows it.","The frame below the tube is cut to one width, 0.69 in (the patent's front view shows it tapering from 0.78 near the tube to 0.62 near the toe), and the butt's flare into it is a step 0.35 in ahead of the pad's seam, where the patent's bottom plan shows a taper.","The six openings the side photo shows are cut through; the rubber butt pad is its own part behind its seam. The release latch is its side silhouette in the frame's window, at the frame's width. The pad's face is checkered as the patent draws it (FIG. 1, FIG. 5): V-grooves both ways at its 0.122 in pitch, 0.033 in deep, leaving square pyramids that touch at their bases, as the patent's edge-on profile shows them (2026-10-03: they had been square grooves), from 1.27 in below the pad's top to its toe. Not drawn: the recessed panels, the pad's two screws, the markings. Edges broken at 0.03 in.","Bored from its front for the receiver extension, a keyhole: the bore at 1.158 in, the hidden circle on the patent's front view (± 0.04, which takes in the mil-spec tube's 1.148: no clearance is claimed), one diameter all the way; under it the indexing rail's channel at the rail's own width and depth (0.49 in, to 0.874 in below the axis), with nothing to spare: no clearance is known, and the mouth the patent draws hasn't been read for it. It ends where the tube's rear end reaches with the stock collapsed (the buffer kit's tube); the real bore's end and its mouth's flare aren't sourced. The two cheek slots, cut right across, open into it.","Its seat on the tube is read from Magpul's photo of it on a rifle two steps out (the traced outline fitted between the receiver's pins), less the two steps: ± 0.08 in. Magpul's lengths of pull for it and the MOE SL, whose seat is read from a photo of it collapsed, put it 0.04 in further forward: they agree."],"ledger":["magpul-moe-carbine.length","magpul-moe-carbine.height","magpul-moe-carbine.width","magpul-moe-carbine.tube_axis_below_top","magpul-moe-carbine.frame_width","magpul-moe-carbine.butt_behind_pin_pos1","magpul-moe-carbine.pad_check_pitch","magpul-moe-carbine.pad_check_depth","magpul-moe-carbine.pad_check_top","magpul-moe-carbine.bore_diameter","magpul-moe-carbine.rail_channel_width","magpul-moe-carbine.rail_channel_floor_below_axis"]},"profiles":{"side":{"plane":"xy","origin":"rearmost point of the butt pad (x) and the top edge at its highest (y); the photo shows the top level, so the tube axis is horizontal","offset":{"y":"tube_axis_below_top"},"points":[[0,-0.76],[0.151,-1.558],[0.165,-1.645],[0.156,-1.682],[0.174,-1.7],[0.188,-1.765],[0.358,-2.866],[0.464,-3.766],[0.56,-4.982],[0.631,-5.09],[0.727,-5.145],[0.879,-5.149],[0.911,-5.181],[0.952,-5.191],[1.255,-5.191],[1.434,-5.181],[1.554,-5.126],[1.666,-4.991],[1.698,-4.872],[1.765,-4.787],[3.197,-3.795],[4.431,-2.965],[4.592,-2.841],[4.844,-2.689],[6.281,-1.716],[6.34,-1.693],[6.68,-1.693],[6.753,-1.735],[6.808,-1.739],[6.928,-1.712],[6.953,-1.687],[6.967,-1.613],[7.013,-0.659],[6.99,-0.278],[6.962,-0.122],[6.937,-0.087],[6.854,-0.05],[0.842,-0.05],[0.741,-0.046],[0.682,0],[0.475,0],[0.425,-0.014],[0.388,-0.05],[0.273,-0.055],[0.117,-0.092],[0.064,-0.145],[0.018,-0.356]],"features":{"through":[[[4.846,-1.053],[4.865,-1.017],[4.922,-0.978],[5.771,-0.973],[5.829,-1.049],[5.81,-1.118],[5.757,-1.152],[5.239,-1.157],[4.876,-1.157],[4.851,-1.122]],[[1.368,-1.099],[1.368,-1.058],[1.386,-1.012],[1.42,-0.987],[2.37,-0.991],[2.432,-1.04],[2.446,-1.113],[2.416,-1.161],[2.361,-1.17],[1.443,-1.17],[1.391,-1.14]],[[1.285,-1.944],[1.294,-1.879],[1.361,-1.785],[1.439,-1.744],[1.558,-1.73],[2.875,-1.716],[2.887,-1.728],[2.857,-1.749],[2.37,-1.941],[2.322,-1.976],[2.286,-2.035],[2.281,-2.077],[2.308,-2.182],[2.304,-2.237],[2.318,-2.269],[2.347,-2.286],[3.678,-1.923],[4.101,-1.891],[4.126,-1.833],[4.137,-1.822],[4.153,-1.838],[4.19,-1.911],[4.199,-2.035],[4.158,-2.146],[4.105,-2.208],[1.898,-3.951],[1.783,-4.002],[1.71,-4.002],[1.636,-3.979],[1.556,-3.912],[1.515,-3.83],[1.432,-3.018]],[[0.959,-2.343],[0.964,-2.269],[1.021,-2.226],[1.081,-2.23],[1.129,-2.274],[1.166,-2.467],[1.28,-3.38],[1.276,-3.444],[1.246,-3.474],[1.2,-3.488],[1.136,-3.465],[1.097,-3.398],[1.028,-2.793]],[[2.478,-3.747],[2.504,-3.708],[3.417,-3.038],[3.481,-3.029],[3.534,-3.063],[3.543,-3.132],[3.504,-3.176],[2.586,-3.837],[2.531,-3.832],[2.487,-3.793]],[[1.198,-4.84],[1.198,-4.78],[1.214,-4.764],[1.393,-4.768],[1.455,-4.835],[1.411,-4.869],[1.237,-4.869]]],"buttpad":[[[-1.14,0.507],[0.383,0.507],[0.374,-0.021],[0.296,-0.457],[0.305,-0.916],[0.383,-1.375],[0.489,-1.833],[0.567,-2.292],[0.649,-2.751],[0.718,-3.21],[0.764,-3.669],[0.81,-4.128],[0.856,-4.587],[0.888,-5.023],[0.906,-5.712],[-1.14,-5.712]]],"frame":[[[0.773,-1.558],[4.872,-1.558],[4.872,-1.925],[8.13,-1.925],[8.13,-5.712],[1.255,-5.712],[1.237,-5.023],[1.205,-4.587],[1.159,-4.128],[1.113,-3.669],[1.067,-3.21],[0.998,-2.751],[0.916,-2.292],[0.838,-1.833]]]},"scaleRefs":["magpul-moe-carbine.length","magpul-moe-carbine.height"],"inputs":{"magpul-moe-carbine.height":5.2,"magpul-moe-carbine.length":7},"tolerance":0.01,"photo":"references/magpul-moe-carbine feb6b40bc741 (Primary Arms MAG400-BLK_00.jpg, straight right side on white, 2000 x 1333)","method":"luminance < 235, closing ×2, largest piece, holes filled; scale from magpul-moe-carbine.length = 7 in (x-extent 1528 px → 218.3 px/in) and magpul-moe-carbine.height = 5.2 in (y-extent 1131 px → 217.5 px/in), which agree within 0.4%; mean 217.9 px/in; origin at x min, y max of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 47 points (IoU 0.997 with the full outline); features through the same placement (through: reviewed pixel boxes; buttpad: reviewed pixel boxes; frame: reviewed pixel boxes) (tools/trace.py)","via":"harvest","note":"The six openings are cut through. The latch, the recessed panels and the markings aren't in the outline."},"front":{"plane":"zy","origin":"the top edge, centred: as the side profile, offset down to the tube axis","offset":{"y":"tube_axis_below_top"},"points":[[-0.848,-1.009],[-0.699,-1.911],[-0.609,-2.994],[-0.59,-3.69],[-0.622,-4.702],[-0.603,-4.85],[-0.519,-5.024],[-0.4,-5.131],[-0.329,-5.169],[-0.142,-5.215],[0.161,-5.215],[0.348,-5.163],[0.451,-5.092],[0.577,-4.947],[0.616,-4.792],[0.609,-4.148],[0.596,-4.122],[0.603,-3.606],[0.59,-3.561],[0.603,-3.548],[0.596,-3.394],[0.609,-3.368],[0.603,-3.2],[0.616,-3.181],[0.622,-2.826],[0.641,-2.73],[0.648,-2.459],[0.661,-2.446],[0.654,-2.395],[0.674,-2.311],[0.706,-1.879],[0.738,-1.782],[0.77,-1.466],[0.802,-1.312],[0.796,-1.273],[0.835,-1.112],[0.848,-0.97],[0.815,-0.822],[0.68,-0.448],[0.564,-0.255],[0.425,-0.129],[0.322,-0.071],[0.18,-0.019],[0,-0.006],[-0.013,0],[-0.116,-0.006],[-0.335,-0.077],[-0.413,-0.122],[-0.545,-0.235],[-0.622,-0.338],[-0.667,-0.429],[-0.712,-0.57],[-0.777,-0.706]],"scaleRefs":["magpul-moe-carbine.height","magpul-moe-carbine.width"],"inputs":{"magpul-moe-carbine.height":5.2,"magpul-moe-carbine.width":1.7},"tolerance":0.01,"photo":"references/magpul-moe-carbine a74bc8906efc (US D600,308 S (Magpul), FIG. 4 front elevation, 300 dpi)","method":"luminance < 128, inside [440, 2740, 1290, 3050], closing ×3, largest piece, holes filled, inset 2 px (half the outline's stroke); rotated -90.0° as declared; scale from magpul-moe-carbine.height = 5.2 in (y-extent 809 px → 155.6 px/in) and magpul-moe-carbine.width = 1.7 in (x-extent 263 px → 154.7 px/in), which agree within 0.6%; mean 155.1 px/in; origin at x center, y max of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 53 points (IoU 0.995 with the full outline) (tools/trace.py)","via":"harvest","note":"The sheet has the figure turned a quarter (the stock's top at the left). Seen from the front; the outline is symmetric but for the latch's two tabs at mid-height."}},"gaps":[{"what":"Its seat on the tube to better than 0.08 in (Magpul's two photos of it on a rifle differ by 0.1)","need":"a straight side photo of it collapsed on a lower with both receiver pins in view"},{"what":"The frame's widths: the upright, the strut, the brace, and the butt's flare","need":"a rear or underside photo square-on with a known size in frame"}]},"magpul-moe-k2-plus":{"id":"magpul-moe-k2-plus","name":"MOE-K2+ grip","manufacturer":"Magpul","sku":"MAG532","category":"grip","weight":"magpul-moe-k2-plus.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"grip_lug":{"origin":["-{.seat_x}",0,0],"note":"Grip frame: origin at the rear end of its flat top, which bears on the lower's underside. The anchor is the point of that top at the takedown pin's x once installed (seat_x)."}},"interfaces":{"grip_lug":{"type":"ar15.grip_lug","role":"grip","anchor":"grip_lug","params":{},"flips":false}},"materials":{"body":{"label":"Grip","finish":"polymer","recolorable":true,"color":"magpul-black","sheen":"matte","detail":"stipple","options":{"black":{"label":"Black","finish":"polymer","color":"magpul-black","sheen":"matte","sku":"MAG532-BLK","source":"https://magpul.com/moe-k2-plus-grip-ar15-m4.html"},"fde":{"label":"FDE","finish":"polymer","color":"magpul-fde","sheen":"matte","sku":"MAG532-FDE","source":"https://magpul.com/moe-k2-plus-grip-ar15-m4.html"},"odg":{"label":"ODG","finish":"polymer","color":"magpul-odg","sheen":"matte","sku":"MAG532-ODG","source":"https://magpul.com/moe-k2-plus-grip-ar15-m4.html"},"sgy":{"label":"Stealth Gray","finish":"polymer","color":"magpul-stealth-gray","sheen":"matte","sku":"MAG532-GRY","source":"https://magpul.com/moe-k2-plus-grip-ar15-m4.html"}},"default":"black","note":"The rubber overmould, in Magpul's four colours for MAG532 (its page's swatches: Black, Flat Dark Earth, Olive Drab Green, Stealth Gray, each with its number), as matched on the MOE SL. Stippled sides (a generated stipple, M4 step 4); the straps and edges keep the polymer's grain (M5). The logo plate is drawn as a recess (2026-10-13: geometry), its floor stippled as the rest is: on the real grip the plate is smooth and lettered, which would be a look of its own."},"base":{"label":"Base and cap","finish":"polymer","recolorable":false,"color":"magpul-black","sheen":"matte","note":"The hard polymer core where it shows: the lip round the bottom and the cap in it, black on every colour of grip (Magpul's gallery shots 01 of the FDE, ODG and Stealth Gray ones, references/magpul-moe-k2-plus 927418fbea1a, 72d990bb5374, ca9715288373; Mile High Shooting's FDE photos). Drawn as everything below the overmould's lower edge as a seller's FDE photo has it from the side (2026-10-13; Primary Arms, 5aa8d0d21f23): beside the bottom edge, 0.166 in up the strap's axis, and up in a step mid-side to 0.296 over the opening the cap's latch sits in (the ledger's base_lip_height, base_tab_*; the model's manifest, `base`). Until then it was cut square across at 0.239 in, the waist the user's rear view of their own grip has under that edge. The cap's latches, one each side, are this piece too."}},"components":{"body":{"label":"Grip","material":"body"},"base":{"label":"Base and cap","material":"base"}},"geometry":{"model":"magpul-moe-k2-plus.glb","components":{},"approximations":["Built about its strap's axis from three views (2026-10-04, from the user's photos of their own grip): the side outline (scaled by its drop, 4.15 in on the user's grip beside a tape), their grip seen from behind (its width at each place down the axis: the beavertail's saddle and horns, the top block, the shoulder, the body, the lip at the base) and from above (the nose's trapezoid, the beavertail tapering to its tip). The body is a section square to the axis at every corner of the side outline, so the straps' ribs are kept and run round the straps: a rounded rectangle from strap to strap, as wide as the rear view has it there.","Its corners are rounded where the ribs stop short of the sides in the rear view (the ribbed face 0.75 in across a body 1.2 wide), as circular arcs, the same front and back: how the straps round fore and aft isn't seen in any view. The two user views are each scaled by the body's thickness (Magpul's 1.2 in, a maximum: the lip at the base; the user's grip 1.195) and see the top of the grip nearer the lens than its body: the top block is brought to the 0.88 in the lens's height gives, the plan to the side view's length.","The top is cut for the receiver (2026-10-05): the slot for its lug as wide as the user's own grip has it from above (0.425 in, read against the top face's width in the same photo), its rear wall and sloped floor the standard lug's own faces (the Army drawing's: the face the screw goes into 1.228 in from the takedown pin at 60°, the flat it ends in .93 below the seat), as far off as the slot's width leaves the lug clear at each side (0.025), and open at the front, where the lug runs on into the trigger guard's ears. Between the beavertail's horns, the round of a receiver's rear underside at the same clearance: half-round across as the reference CAD model has it, along the arc of the fullest forging on file (the Workhorse's, 0.034 in fuller than the model's: a grip goes on any lower). No view on file looks into the scoop square. Nothing else stands above the face that bears on the receiver. Until then the grip had no slot, and in a build its top block stood in the lower's lug.","The relief under the top block (2026-10-13, the pass over the models' detail): between the block (0.88 in across) and the body (1.2) each side is a floor that leaves the block's side along a straight upper edge and, under it, a steeper band whose lower edge sweeps in a curve from the back strap down under the logo plate and up toward the nose. The three lines are Magpul's patent's (the MOE-K2's side elevation, FIG. 11, laid on this grip's outline: the ledger's relief_*); the user's own grip and a seller's FDE one have the band where the patent draws it. How far in each stands is read off outlines: the floor has widened the grip 0.05 in each side where the band begins (the patent's front elevation, at the relief's rear end), and the band comes out to what the user's rear view of their own grip has as the grip's width at that place down the strap, which toward the nose is less than the body's. Assumed: the floor leaves the block's side without a crease and steepens to the band, the band is straight, and toward the front, where the rear view allows the grip less than twice the floor's rise over the block, the floor takes half of it and the band the rest; behind its rear end the relief runs out level into the back strap's round. Ahead of x 0.95 the relief's lower edge climbs the nose beside the block's front edge in the patent: not drawn, the nose is the three-view hull it was. Until then the shoulder was straight across the grip, square to the strap. The sections reach up into the block now, so the block's side and the floor are one surface; and the two user views' outlines are each made the same both sides (the wider of the two at each place): as traced, the nose's right side stood up to 0.05 in inside its left and the top 0.001 proud of the sections on one side.","The beavertail (2026-10-13): the side outline's stretch round it, traced as points up to 0.4 in apart, is carried through them as a curve (each chord was a facet), and the two edges of its rear face are rounded 0.11 in from under its tip to the shoulder (the patent's rear elevation has a line that far inside each edge: beavertail_edge_round), by which they have become the neck's own corner round. Round the tip itself the outline turns tighter than that round, and the edges there are as they were. The top's other edges are asked to be broken at 0.05 in, which the outlines' short edges hold to a few thousandths.","The logo plate (2026-10-13): a recess with rounded corners on the right of the top block, 0.87 by 0.24 in, where a seller's FDE photo has it (logo_plate_*: the user's own grip has it 0.03 in higher, inside the two readings together). Assumed: sunk 0.02 in, its walls at 45 degrees, so that it shows from the side at all; in the app's even light it is faint. Its lettering isn't drawn, and its floor is stippled like the rest (materials.body). No photo on file shows the left side of the top block square on: the left has no plate.","The base (2026-10-13): the overmould's lower edge runs beside the bottom edge and rises in a step mid-side, as the FDE photo has it and the user's own black grip as a hairline (materials.base); the waist the user's rear view has under that edge, 0.023 in deep, is drawn under the step and dies out down its two ends (the rear view is the grip's widest, which is mid-side: whether the lip is waisted at the corners isn't seen). Under the step each side has the opening the cap's latch sits in, open at the bottom, with the latch standing in it (latch_*). Assumed: the opening sunk 0.05 in and the latch's face 0.01 under the lip's (latch_window_depth, detail_relief); the left side as the right (the patent's rear elevation and bottom plan are symmetric, and a seller's photo of the base with its cap off has a notch in each side's rim). Not drawn: the cap's own outline under the base, its MOE lettering.","Not drawn: the screw's hole, the detent spring's hole and the storage core's opening in the top, the shallow step round the slot's mouth (all under the receiver once installed). It is seated by what it touches (2026-10-05): the foremost point of its top block on the rear face of the trigger guard's ears, where the Army's drawing has that face, as a MOE-K2 sits on a mil-spec lower in the photo on file. On the Workhorse lower, whose own ears are traced within 0.003 in of the drawing's, the two models share nothing (until that day its outline, traced in a frame set by its two pins alone, had its ears 0.045 further back, and the nose stood 0.03 into them). It leans as its flat top says (2026-10-05, when the user asked for the grip to be looked at): its straps 17.9° from square to the face that lies on the receiver, as the photo it is traced from has them as shot, Magpul's patent elevation, and the grip on a rifle. Until then the outline was turned 2° too upright: the block's front face leaned and stood off the ears by up to 0.025 in at its top, and its heel was a tenth of an inch too far forward. Until 2026-10-04 it was a hull of the side outline and Magpul's design-patent front elevation: as wide at its straps as at its middle."],"ledger":["magpul-moe-k2-plus.grip_angle","magpul-moe-k2-plus.bottom_below_lower_underside","magpul-moe-k2-plus.thickness","magpul-moe-k2-plus.overall_height","magpul-moe-k2-plus.toe_y","magpul-moe-k2-plus.top_block_width","magpul-moe-k2-plus.strap_face_width","magpul-moe-k2-plus.lug_slot_width","magpul-moe-k2-plus.seat_x","magpul-moe-k2-plus.relief_top_rear_x","magpul-moe-k2-plus.relief_top_rear_y","magpul-moe-k2-plus.relief_top_front_x","magpul-moe-k2-plus.relief_top_front_y","magpul-moe-k2-plus.relief_floor_rear_x","magpul-moe-k2-plus.relief_floor_rear_y","magpul-moe-k2-plus.relief_floor_low_x","magpul-moe-k2-plus.relief_floor_low_y","magpul-moe-k2-plus.relief_floor_front_x","magpul-moe-k2-plus.relief_floor_front_y","magpul-moe-k2-plus.relief_band_width","magpul-moe-k2-plus.relief_edge_rear_x","magpul-moe-k2-plus.relief_edge_rear_y","magpul-moe-k2-plus.relief_floor_rise","magpul-moe-k2-plus.logo_plate_rear_x","magpul-moe-k2-plus.logo_plate_length","magpul-moe-k2-plus.logo_plate_top_y","magpul-moe-k2-plus.logo_plate_height","magpul-moe-k2-plus.logo_plate_corner_r","magpul-moe-k2-plus.detail_relief","magpul-moe-k2-plus.beavertail_edge_round","magpul-moe-k2-plus.base_lip_height","magpul-moe-k2-plus.base_tab_height","magpul-moe-k2-plus.base_tab_rear_foot_u","magpul-moe-k2-plus.base_tab_rear_top_u","magpul-moe-k2-plus.base_tab_front_top_u","magpul-moe-k2-plus.base_tab_front_foot_u","magpul-moe-k2-plus.latch_window_rear_u","magpul-moe-k2-plus.latch_window_front_u","magpul-moe-k2-plus.latch_window_height","magpul-moe-k2-plus.latch_height","magpul-moe-k2-plus.latch_end_gap","magpul-moe-k2-plus.latch_window_depth","std.ar15.grip_lug_width","std.ar15.grip_lug_face_from_pin","std.ar15.grip_lug_face_angle","std.ar15.grip_lug_depth","std.ar15.grip_seat_below_deck","std.ar15.rear_underside_arc_r_fullest","std.ar15.rear_underside_round_r"]},"profiles":{"side":{"plane":"xy","origin":"rear end of the grip's flat top, which sits at the lower's grip-shelf step (the grip frame origin)","offset":{},"points":[[-1.631,-3.508],[-1.627,-3.543],[-1.594,-3.589],[-1.458,-3.668],[-1.318,-3.72],[-1.02,-3.82],[-0.994,-3.82],[-0.972,-3.798],[-0.919,-3.842],[-0.433,-3.994],[-0.35,-4.015],[-0.319,-4.011],[-0.297,-4.037],[0.184,-4.15],[0.237,-4.15],[0.307,-4.115],[0.348,-4.064],[0.392,-3.977],[0.387,-3.889],[0.313,-3.776],[0.291,-3.701],[0.291,-3.609],[0.321,-3.509],[0.312,-3.478],[0.343,-3.438],[0.343,-3.39],[0.369,-3.351],[0.364,-3.311],[0.395,-3.268],[0.39,-3.224],[0.421,-3.184],[0.416,-3.141],[0.443,-3.11],[0.443,-3.057],[0.473,-3.009],[0.464,-2.974],[0.499,-2.926],[0.49,-2.891],[0.521,-2.847],[0.516,-2.808],[0.547,-2.76],[0.543,-2.72],[0.573,-2.681],[0.564,-2.641],[0.599,-2.593],[0.59,-2.554],[0.625,-2.51],[0.616,-2.471],[0.651,-2.422],[0.643,-2.387],[0.677,-2.335],[0.669,-2.3],[0.699,-2.26],[0.695,-2.217],[0.725,-2.182],[0.721,-2.129],[0.751,-2.094],[0.742,-2.05],[0.777,-2.006],[0.769,-1.967],[0.795,-1.941],[0.803,-1.914],[0.795,-1.879],[0.821,-1.853],[0.83,-1.822],[0.821,-1.796],[0.843,-1.774],[0.856,-1.744],[0.847,-1.709],[0.882,-1.66],[0.873,-1.621],[0.899,-1.59],[0.943,-1.476],[1.01,-1.391],[1.063,-1.351],[1.141,-1.316],[1.203,-1.307],[1.255,-1.312],[1.275,-1.296],[1.292,-1.257],[1.314,-1.152],[1.322,-1.056],[1.318,-0.99],[1.327,-0.977],[1.317,-0.723],[1.33,-0.307],[1.321,-0.233],[1.286,-0.145],[1.222,-0.064],[1.139,-0.012],[1.086,0.001],[0.202,-0.001],[0.132,0.008],[0.073,0.062],[0.038,0.154],[-0.037,0.285],[-0.162,0.427],[-0.289,0.519],[-0.372,0.562],[-0.508,0.606],[-0.626,0.623],[-0.71,0.623],[-0.793,0.605],[-0.941,0.57],[-0.97,0.546],[-0.978,0.458],[-0.974,0.226],[-0.96,0.191],[-0.936,0.167],[-0.625,-0.081],[-0.526,-0.197],[-0.478,-0.302],[-0.456,-0.407],[-0.456,-0.508],[-0.469,-0.578],[-0.499,-0.665],[-0.543,-0.74],[-0.73,-0.964],[-0.774,-1.038],[-0.787,-1.073],[-0.783,-1.091],[-0.813,-1.121],[-0.813,-1.178],[-0.839,-1.196],[-0.848,-1.218],[-0.844,-1.261],[-0.874,-1.288],[-0.874,-1.345],[-0.896,-1.362],[-0.909,-1.402],[-0.9,-1.428],[-0.931,-1.458],[-0.931,-1.511],[-0.961,-1.546],[-0.961,-1.599],[-0.983,-1.616],[-0.996,-1.656],[-0.991,-1.682],[-1.018,-1.713],[-1.018,-1.765],[-1.048,-1.796],[-1.048,-1.848],[-1.074,-1.875],[-1.083,-1.91],[-1.078,-1.931],[-1.1,-1.953],[-1.109,-1.984],[-1.105,-2.015],[-1.131,-2.041],[-1.139,-2.072],[-1.135,-2.098],[-1.161,-2.129],[-1.17,-2.172],[-1.161,-2.181],[-1.187,-2.207],[-1.196,-2.234],[-1.192,-2.264],[-1.218,-2.295],[-1.226,-2.326],[-1.222,-2.352],[-1.248,-2.383],[-1.252,-2.435],[-1.279,-2.47],[-1.279,-2.518],[-1.3,-2.536],[-1.313,-2.58],[-1.309,-2.602],[-1.335,-2.637],[-1.335,-2.685],[-1.357,-2.702],[-1.366,-2.724],[-1.366,-2.768],[-1.392,-2.803],[-1.396,-2.851],[-1.414,-2.869],[-1.422,-2.895],[-1.422,-2.934],[-1.444,-2.956],[-1.453,-3.018],[-1.47,-3.035],[-1.479,-3.062],[-1.479,-3.101],[-1.501,-3.123],[-1.509,-3.184],[-1.531,-3.215],[-1.535,-3.263],[-1.588,-3.355],[-1.587,-3.39]],"scaleRefs":["magpul-moe-k2-plus.bottom_below_lower_underside"],"angleRef":"magpul-moe-k2-plus.grip_angle","inputs":{"magpul-moe-k2-plus.bottom_below_lower_underside":4.15,"magpul-moe-k2-plus.grip_angle":17.89},"tolerance":0.006,"photo":"references/magpul-moe-k2-plus 706ec3ae3e86 (black MOE-K2+, side view on white; supplied in chat, source not recorded)","method":"luminance < 200, closing ×2, largest piece, holes filled; rotated +0.1° (counter-clockwise) so the edges' mean lean in the band 0.45–0.85 of the height (19.1° rear, 16.9° front in the photo) becomes magpul-moe-k2-plus.grip_angle = 17.89°; re-measured 19.0°/16.8°; scale from magpul-moe-k2-plus.bottom_below_lower_underside = 4.15 in (y from the origin to the far edge 948 px → 228.5 px/in); origin at the rear end of the flat top; Douglas-Peucker at 0.006 in with the extremes kept: 188 points (IoU 0.997 with the full outline); checks: angle from the vertical of the straight line through the outline in x [1.2, 1.45] in y [-1.15, -0.26] (0.88 in of it, rms 0.003) 0.327 ± 0.930 (tools/trace.py)","via":"user","note":"Includes the beavertail (above the shelf line; it tucks under the lower's tang) and the nose that fills the gap behind the trigger guard. Stippling and finger ribs are M4 texture."},"front":{"plane":"zy","origin":"the toe (lowest point), centred; offset to the side profile's toe","offset":{"y":"toe_y"},"points":[[-0.612,0.33],[-0.594,0.268],[-0.516,0.164],[-0.344,0.014],[-0.278,0],[0.334,0.01],[0.531,0.179],[0.602,0.286],[0.612,0.374],[0.594,0.508],[0.602,3.093],[0.471,3.454],[0.447,3.589],[0.447,4.511],[0.433,4.658],[0.397,4.744],[0.352,4.773],[0.175,4.667],[0.101,4.643],[-0.035,4.635],[-0.179,4.667],[-0.358,4.773],[-0.417,4.712],[-0.443,4.598],[-0.449,3.581],[-0.487,3.398],[-0.558,3.232],[-0.598,3.059],[-0.594,0.5]],"scaleRefs":["magpul-moe-k2-plus.overall_height"],"inputs":{"magpul-moe-k2-plus.overall_height":4.773},"tolerance":0.01,"photo":"references/magpul-moe-k2-plus b0f42d6a9b13 (US D742,986 S (Magpul MOE-K2), FIG. 12 front elevation, 300 dpi)","method":"luminance < 128, inside [530, 460, 1180, 2865], closing ×3, the piece at [549, 1700], holes filled, inset 2 px (half the outline's stroke); scale from magpul-moe-k2-plus.overall_height = 4.773 in (y-extent 2380 px → 498.6 px/in); origin at x center, y min of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 29 points (IoU 0.994 with the full outline); checks: width 1.223 ± 0.014 in vs magpul-moe-k2-plus.thickness 1.2 ± 0 (confirmed): DISAGREES (tools/trace.py)","via":"harvest","note":"The K2's outline; the K2+'s overmold isn't separately dimensioned. Seen from the front, so its right is the grip's left; the outline is symmetric. Scaled by the height the side view shows, it is about 1.36 wide, not Magpul's 1.2 (a conflict on thickness): the model narrows it to the adopted thickness."},"rear":{"plane":"zy","origin":"the horns' tips, centred: y runs down the strap's axis (the view is square to it), not down the grip frame's y","offset":{},"points":[[-0.6,-4.309],[-0.579,-4.355],[-0.501,-4.416],[-0.459,-4.432],[-0.262,-4.449],[0.022,-4.452],[0.476,-4.43],[0.574,-4.363],[0.597,-4.331],[0.592,-4.233],[0.572,-4.211],[0.569,-4.167],[0.592,-4.128],[0.594,-3.69],[0.581,-3.679],[0.592,-3.629],[0.6,-1.797],[0.592,-1.786],[0.589,-1.407],[0.477,-1.126],[0.452,-1.02],[0.455,-0.174],[0.447,-0.063],[0.43,-0.026],[0.404,-0.006],[0.365,-0.003],[0.29,-0.07],[0.187,-0.125],[0.064,-0.161],[-0.019,-0.167],[-0.203,-0.117],[-0.365,-0.003],[-0.401,0],[-0.436,-0.026],[-0.455,-0.113],[-0.452,-1.029],[-0.469,-1.057],[-0.475,-1.121],[-0.575,-1.357],[-0.594,-1.441],[-0.592,-4.13],[-0.575,-4.206],[-0.592,-4.236]],"scaleRefs":["magpul-moe-k2-plus.thickness"],"inputs":{"magpul-moe-k2-plus.thickness":1.2},"tolerance":0.008,"photo":"references/magpul-moe-k2-plus 348ac23e1f32 (the user's own K2+ lying on its front strap, its back strap straight on, a tape beside it)","method":"luminance < 75, closing ×2, largest piece, holes filled; scale from magpul-moe-k2-plus.thickness = 1.2 in (x-extent 431 px → 359.2 px/in); origin at x center, y max of the outline; Douglas-Peucker at 0.008 in with the extremes kept: 43 points (IoU 0.995 with the full outline) (tools/trace.py)","via":"user","note":"Square to the strap's axis, which leans grip_angle from the grip frame's y. The top block and the horns stand 1.4 in nearer the lens than the body's widest and read 4% wide (0.92 for the 0.88 the lens's height gives: top_block_width)."},"plan":{"plane":"xz","origin":"the nose's front face, centred: x runs aft square to the strap's axis","offset":{},"points":[[-2.729,-0.176],[-2.723,-0.296],[-2.712,-0.316],[-2.492,-0.431],[-2.329,-0.483],[-2.174,-0.498],[-1.956,-0.565],[-1.749,-0.6],[-1.353,-0.58],[-1.073,-0.536],[-1.05,-0.548],[-1.024,-0.527],[-1.003,-0.542],[-0.995,-0.521],[-0.907,-0.486],[-0.756,-0.486],[-0.447,-0.451],[-0.275,-0.414],[-0.025,-0.329],[0,-0.272],[-0.012,0.051],[-0.003,0.234],[-0.033,0.28],[-0.368,0.382],[-0.572,0.417],[-0.782,0.434],[-0.84,0.486],[-0.919,0.516],[-1.292,0.559],[-1.35,0.571],[-1.379,0.591],[-1.618,0.6],[-1.737,0.594],[-1.752,0.583],[-1.947,0.553],[-2.442,0.402],[-2.71,0.297],[-2.726,0.261]],"scaleRefs":["magpul-moe-k2-plus.thickness"],"inputs":{"magpul-moe-k2-plus.thickness":1.2},"tolerance":0.008,"photo":"references/magpul-moe-k2-plus 45eafc02ec88 (the user's own K2+ standing on its base, its top straight on from above, a tape beside it)","method":"luminance < 95, closing ×2, largest piece, holes filled; rotated +90.0° as declared; scale from magpul-moe-k2-plus.thickness = 1.2 in (y-extent 412 px → 343.3 px/in); origin at x max, y center of the outline; Douglas-Peucker at 0.008 in with the extremes kept: 38 points (IoU 0.994 with the full outline) (tools/trace.py)","via":"user","note":"Its widest is the body's bulge, 2.8 in above the floor; the nose and the beavertail stand 4.1 to 4.4 in up and read 4.5% large against it. The model scales this outline to the side view's length from the nose's front to the beavertail's tip, which are both at the top."}},"gaps":[{"what":"Whether the left side of the top block has a plate as the right has (it is drawn bare), and the plate's place below the top on a view square to it (the two photos read differ by 0.03 in)","need":"The grip's left side and its right side, each square on from 8 ft or more, zoomed, with a tape lying on the grip"},{"what":"How deep the relief under the top block stands in along its length (its lines are the patent's; its depth is from two outlines, and toward the nose assumed), and how the logo plate and the latch's opening are sunk (assumed: 0.02 and 0.05 in)","need":"The grip from below its base looking up along the strap, and from the front looking straight back along the rifle, each from 8 ft or more, zoomed: the outlines the relief makes"},{"what":"The relief's lower edge where it climbs the nose, and the nose's cheeks (drawn as the hull of three outlines; the patent has the block's front edge as a band up the nose)","need":"The grip from the front quarter, right and left, from 8 ft or more, zoomed"},{"what":"The beavertail's tip, whose edges are broken by thousandths where the grip's are round, and how its rear face rounds across (0.11 in by the patent's MOE-K2)","need":"The grip from behind, square to its back strap, from 8 ft or more, zoomed, with a tape lying on it"},{"what":"The cap under the base (its outline, the MOE lettering) and the top face under the receiver (the screw's hole, the detent spring's hole, the step round the slot)","need":"Nothing more for the top: the user's photos of it are on file (9455489fc6df, 906083dafd0e, 45eafc02ec88) and it is hidden once installed. For the cap: the base straight on from below with a tape lying on it"}]},"magpul-moe-mlok-handguard-carbine":{"id":"magpul-moe-mlok-handguard-carbine","name":"MOE® M-LOK® Hand Guard, Carbine-Length – AR15/M4","manufacturer":"Magpul","sku":"MAG424","url":"https://magpul.com/moem-lokhandguard-carbine-length-ar15-m4.html","category":"handguard","description":"Magpul's polymer drop-in hand guard for a carbine-length gas system, in two halves: \"Replaces standard AR15/M4 hand guards on carbine-length gas systems\"; \"Compatible with most piston-driven as well as 'direct impingement' gas systems\"; \"M-LOK slots at the two, six, and ten o'clock positions\"; \"The integral, riveted aluminum heat shield, combined with the front lower lip and side extensions, shields the support hand from a hot gas block\"; \"Relief cut at the top rear of the handguard accommodates overhanging optics\"; \"Constructed of reinforced, heat-resistant Magpul polymer\"; \"Made in the USA\" (Magpul). It goes on the rifle's own barrel nut and delta ring and the cap behind its front sight base: no free-float nut of its own.","weight":"magpul-moe-mlok-handguard-carbine.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"needs":{"slots":["barrel_nut","delta_ring","handguard_cap"],"says":"Magpul: \"Compatible with firearms with delta ring and round or triangular front hand guard retaining caps\", \"Easy to install utilizing existing delta ring and round or triangular front hand guard retaining cap\"; its instructions: \"Slide the front flange of the upper Hand Guard piece into the metal Hand Guard cap, located behind the front sight base\" and \"make sure your delta ring is securing BOTH upper and lower rear flanges\". Magpul's one instruction sheet for the three lengths.","source":"https://magpul.com/moem-lokhandguard-carbine-length-ar15-m4.html"},"anchors":{"mount":{"origin":["0in - {.rear_x}",0,0],"note":"The receiver's front face on the bore axis, +x toward the muzzle: its rear end stands in the delta ring's skirt against the ring's lip (std.ar15.slip_ring_front_x ahead of the receiver)."},"mlok":{"origin":["{.mlok_side_slot0_x}",0,0],"note":"On the bore axis at the upper side faces' rearmost M-LOK slot's centre (index 0), +x toward the muzzle; the faces are angles about this axis."},"mlok_bottom":{"origin":["{.mlok_bottom_slot0_x}",0,0],"note":"The same axis at the underside's rearmost slot's centre, taken at the side rows' (the underside isn't seen: mlok_bottom_slot0_x)."},"cap_seat":{"origin":["{.mounting_length}",0,0],"note":"The front flange's front end, on the bore axis: what goes into the hand guard cap (Magpul's mounting length ahead of its rear end)."}},"interfaces":{"cap_seat":{"type":"ar15.handguard_front","role":"handguard","anchor":"cap_seat","params":{},"flips":false},"handguard_mount":{"type":"ar15.handguard_mount","role":"handguard","anchor":"mount","params":{"nut":"standard"},"flips":false,"note":"On the rifle's own barrel nut and delta ring: Magpul, \"Easy to install utilizing existing delta ring and round or triangular front hand guard retaining cap\". Placed by the standard's delta ring (rear_x): its instructions, \"make sure your delta ring is securing BOTH upper and lower rear flanges of the Hand Guards\"."},"drop_in":{"type":"ar15.drop_in","role":"handguard","params":{"shape":"round|triangle"},"flips":false,"note":"Magpul (its page, read on the harvested copy): \"Compatible with firearms with delta ring and round or triangular front hand guard retaining caps\": either cap."},"gas_system":{"type":"ar15.gas_system","role":"handguard","params":{"length":"carbine"},"flips":false,"note":"Magpul names it \"Carbine-Length\": \"Replaces standard AR15/M4 hand guards on carbine-length gas systems\", \"Compatibility AR15/M4 firearms with carbine-length gas systems\"; Primary Arms: \"Gas System Length Carbine\"."},"mlok":{"type":"mlok","role":"slots","anchor":"mlok","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_side_slots}","interval":"={std.mlok.interval}","face_distance":"={.mlok_side_face_distance}","reach_inside":"={.reach_inside}"},"faces":{"right_upper":{"angle":"{.mlok_side_face_angle}","note":"Magpul's two o'clock (the rifle's right, +z)"},"left_upper":{"angle":"0 - {.mlok_side_face_angle}","note":"Magpul's ten o'clock"}},"flips":false,"note":"Magpul: \"M-LOK slots at the two, six, and ten o'clock positions for mounting MIL-STD-1913 Picatinny rails or other direct-attach M-LOK accessories\". Three in each, counted on Primary Arms' and Magpul's photos."},"mlok_bottom":{"type":"mlok","role":"slots","anchor":"mlok_bottom","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_bottom_slots}","interval":"={std.mlok.interval}","face_distance":"={.mlok_bottom_face_distance}","reach_inside":"={.reach_inside}"},"faces":{"bottom":{"angle":180,"note":"the underside (Magpul's six o'clock)"}},"flips":false,"note":"Magpul's six o'clock row. No view on file looks at the underside: its count and places are the side rows' (mlok_bottom_slots, assumed), and kept as a gap."}},"materials":{"body":{"label":"Hand guard","finish":"polymer","recolorable":true,"color":"magpul-black","sheen":"satin","options":{"black":{"label":"Black","finish":"polymer","color":"magpul-black","sheen":"satin","sku":"MAG424-BLK","source":"https://magpul.com/moem-lokhandguard-carbine-length-ar15-m4.html"},"fde":{"label":"Flat Dark Earth","finish":"polymer","color":"magpul-fde","sheen":"satin","sku":"MAG424-FDE","source":"https://magpul.com/moem-lokhandguard-carbine-length-ar15-m4.html"},"odg":{"label":"Olive Drab Green","finish":"polymer","color":"magpul-odg","sheen":"satin","sku":"MAG424-ODG","source":"https://magpul.com/moem-lokhandguard-carbine-length-ar15-m4.html"},"gry":{"label":"Stealth Gray","finish":"polymer","color":"magpul-stealth-gray-moe-mlok","sheen":"satin","sku":"MAG424-GRY","source":"https://magpul.com/moem-lokhandguard-carbine-length-ar15-m4.html"}},"default":"black","note":"Both halves are one colour in each colourway (Magpul's photos of all four): \"reinforced, heat-resistant Magpul polymer\". Magpul's page names the four (its colour swatches for MAG424: Black, Flat Dark Earth, Olive Drab Green, Stealth Gray); the numbers are Midwest Gun Works' (\"MAG424-BLK Black MAG424-FDE Flat Dark Earth MAG424-GRY Gray MAG424-ODG OD Green\"). Drawn in Magpul's colour presets matched on the MOE SL and the K2+ (data/finishes.yaml); the gray checked against Magpul's own photos of this hand guard in it beside the other three (the report on file: .cache/batch15)."},"heat_shield":{"label":"Heat shield","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"\"The integral, riveted aluminum heat shield\" (Magpul): a bare bright sheet inside the lower half, the same in every colourway (Primary Arms' black one shows it bright through the upper slots, seen across the inside). Drawn in the bright metal finish on file; its alloy and temper aren't stated."}},"components":{},"geometry":{"model":"magpul-moe-mlok-handguard-carbine.glb","components":{},"approximations":["Seated at its cap (the cap's `seats`, ar15.handguard_front): its front flange's end at the inside of the cap's face, and its rear end as far into the delta ring as its mounting length then takes it (a tenth of an inch or so on BCM's barrels). The ring is drawn at its forward stop, as the Army's drawing has it with no hand guard in; on the rifle it gives way that much on its spring (std.ar15.slip_ring_front_x), so what this part and the ring share as drawn is hidden inside the ring.","One model of both halves (the seam a groove along each side, seam_y): the two are never apart on a rifle, they come in one box and one colour, and Magpul sells them as one product.","Its section about the bore is an assumption past what its photo gives (Magpul's width 2.2 in; the top 1.18 and the bottom 1.19 from the bore, the slots' height and the seam's from Primary Arms' level photo of it alone): a flat underside (bottom_half_width) rounding up into upright sides under the pockets, upright sides to the M-LOK faces, which lean in at the angle the level photo shows the slots at (mlok_side_face_angle, 78° from up; Magpul says two and ten o'clock), a flat for the slots (face_flat), and a round crown (top_half_width). No view on file looks at an end square on.","Its height is the photo's (2.38 in clear of the lip, scaled by Magpul's length and by its own M-LOK slots at the standard's pitch, the two within 0.5%); Magpul gives 2.5, which the photo doesn't bear out (height). Its width is Magpul's 2.2 in, which no view on file can check.","Its rear end, in the ring's skirt, is a round collar (rear_collar_od, assumed: a little inside the skirt) cut at each side by the gap the photo sees between the two halves' flanges (rear_collar_gap); the plan's narrowing into it follows the side outline's rounding. The front lower lip runs across the underside to the middle of its rounds.","Inside: the section less a wall of 0.15 in (wall, the mid-length's assumption: the model weighs about 5.7 oz with its shield against Magpul's 6.8, the inner ribs and bosses no view shows not drawn), from a rear wall round the barrel nut to a front wall, ahead of which it is open over the cap and the front sight base's rear. The front flange that goes into the cap is a round lip on the front wall (front_flange_od, front_flange_length: assumed, inside both caps on file), as long as Magpul's mounting length says. The gas tube's way through each end is a notch as wide as the delta ring's own.","Three M-LOK slots in each upper side face at the standard's size and pitch, where the level photo has them; the underside's row of three in line with them (assumed: no view looks at the underside; Magpul's photo with its MVG on shows one slot each side of the grip). Four pockets along each side of the lower half, where the photo has them (their depth assumed). The heat shield is a liner of 0.03 in (assumed) inside the lower half, slotted with the underside's row; its two rivets, which Magpul's MVG photo shows at the ends of the underside's row, aren't drawn.","Four vents through the crown, where the level photo's outline dips at its top (vent0_x, vent_pitch, vent_length), their width assumed (vent_width).","Edges rounded at 0.02 in (moulded; their size isn't read). The lower half's panels stand in a little from the ribs round them (panel_rib, panel_depth: assumed). Not drawn: the Magpul, M-LOK and MOE marks."],"ledger":["magpul-moe-mlok-handguard-carbine.length","magpul-moe-mlok-handguard-carbine.width","magpul-moe-mlok-handguard-carbine.height","magpul-moe-mlok-handguard-carbine.mounting_length","magpul-moe-mlok-handguard-carbine.rear_x"]},"profiles":{"side":{"plane":"xy","origin":"its rear end and its top","offset":{"y":"top_above_axis"},"points":[[0,-0.995],[0.2,-1.424],[0.174,-1.457],[0.129,-1.427],[0.018,-1.435],[0.007,-1.453],[0.03,-1.668],[0.081,-1.89],[0.118,-1.971],[0.159,-2.019],[0.218,-2.026],[0.259,-2.06],[0.311,-2.252],[0.433,-2.359],[0.884,-2.374],[5.861,-2.374],[5.935,-2.396],[5.983,-2.437],[5.991,-2.526],[6.031,-2.603],[6.135,-2.618],[6.198,-2.577],[6.264,-2.393],[6.338,-2.267],[6.497,-2.13],[6.623,-2.093],[6.771,-2.093],[6.911,-2.056],[6.978,-2.026],[7.056,-1.934],[7.1,-1.808],[7.1,-1.106],[7.041,-0.965],[6.656,-0.484],[6.664,-0.47],[6.59,-0.396],[6.56,-0.337],[6.479,-0.263],[6.316,-0.063],[6.238,0],[5.876,0],[5.75,-0.037],[5.203,-0.037],[5.092,0],[4.73,0],[4.604,-0.037],[4.034,-0.037],[3.931,0],[3.576,0],[3.465,-0.037],[2.888,-0.037],[2.77,0],[2.422,0],[2.296,-0.037],[1.764,-0.037],[1.646,0],[0.743,0],[0.714,-0.015],[0.684,0],[0.618,0],[0.514,-0.03],[0.388,-0.104],[0.333,-0.166],[0.318,-0.255],[0.255,-0.348],[0.166,-0.355],[0.111,-0.381],[0.037,-0.64]],"scaleRefs":["magpul-moe-mlok-handguard-carbine.length"],"inputs":{"magpul-moe-mlok-handguard-carbine.length":7.1},"tolerance":0.01,"photo":"references/magpul-moe-mlok-handguard-carbine 7ddb0240610f (Primary Arms' MAG424-BLK_01: the black hand guard alone, its right side seen level on white, 1152 x 768)","method":"luminance < 230, closing ×3, largest piece, holes filled; scale from magpul-moe-mlok-handguard-carbine.length = 7.1 in (x-extent 960 px → 135.2 px/in); origin at x min, y max of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 68 points (IoU 0.998 with the full outline); Scaled by Magpul's overall length; its three M-LOK slots in the same photo, at the standard's 40 mm pitch, give the scale within 0.5%.; checks: −y_min in x [1.0, 5.5] 2.381 ± 0.011 in vs magpul-moe-mlok-handguard-carbine.height 2.38 ± 0.02 (conflict): agrees; −y_min 2.618 ± 0.011 (tools/trace.py)","via":"harvest","note":"Its M-LOK slots, its pockets and the seam are inside the outline (holes filled); the model cuts them from the ledger. The gap between the two halves' rear flanges, where the backdrop shows, is filled with them: the model cuts it (rear_collar_gap)."}},"gaps":[{"what":"Its underside: the six o'clock M-LOK row's count and places, and where the heat shield's rivets are","need":"A photo of a MOE M-LOK carbine-length from below, its whole underside in frame (a seller's gallery or a review)"},{"what":"Its section square on (how wide the crown and the underside are, how the faces lean) and its width","need":"An end view with a known size in frame, or a photo from above; Magpul publishes no drawing"},{"what":"Its wall and what is inside it (ribs, bosses, the flanges' sizes)","need":"A photo into either end, or of a half alone from inside"},{"what":"Magpul's height, 2.5 in excluding the lip, against the photo's 2.38","need":"What Magpul measured over; a seller's or a reviewer's own measurement"}]},"magpul-moe-mlok-handguard-mid":{"id":"magpul-moe-mlok-handguard-mid","name":"MOE® M-LOK® Hand Guard, Mid-Length – AR15/M4","manufacturer":"Magpul","sku":"MAG426","url":"https://magpul.com/moem-lokhandguard-mid-length-ar15-m4.html","category":"handguard","description":"Magpul's polymer drop-in hand guard for a mid-length gas system, in two halves: \"Replaces standard AR15/M4 hand guards on mid-length gas systems\"; \"M-LOK slots at the two, six, and ten o'clock positions\"; \"The integral, riveted aluminum heat shield, combined with the front lower lip and side extensions, shields the support hand from a hot gas block\"; \"Relief cut at the top rear of the handguard accommodates overhanging optics\"; \"Constructed of reinforced, heat-resistant Magpul polymer\"; \"Made in the USA\" (Magpul). It goes on the rifle's own barrel nut and delta ring and the cap behind its front sight base: no free-float nut of its own.","weight":"magpul-moe-mlok-handguard-mid.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"needs":{"slots":["barrel_nut","delta_ring","handguard_cap"],"says":"Magpul: \"Compatible with firearms with delta ring and round or triangular front hand guard retaining caps\"; its instructions: \"Slide the front flange of the upper Hand Guard piece into the metal Hand Guard cap, located behind the front sight base\" and \"make sure your delta ring is securing BOTH upper and lower rear flanges\". Primary Arms: \"this handguard drops directly onto the existing barrel nut and delta ring\".","source":"https://magpul.com/moem-lokhandguard-mid-length-ar15-m4.html"},"anchors":{"mount":{"origin":["0in - {.rear_x}",0,0],"note":"The receiver's front face on the bore axis, +x toward the muzzle: its rear end stands in the delta ring's skirt against the ring's lip (std.ar15.slip_ring_front_x ahead of the receiver)."},"mlok":{"origin":["{.mlok_side_slot0_x}",0,0],"note":"On the bore axis at the upper side faces' rearmost M-LOK slot's centre (index 0), +x toward the muzzle; the faces are angles about this axis."},"mlok_bottom":{"origin":["{.mlok_bottom_slot0_x}",0,0],"note":"The same axis at the underside's rearmost slot's centre, taken at the side rows' (the underside isn't seen: mlok_bottom_slot0_x)."},"cap_seat":{"origin":["{.mounting_length}",0,0],"note":"The front flange's front end, on the bore axis: what goes into the hand guard cap (Magpul's mounting length ahead of its rear end)."}},"interfaces":{"cap_seat":{"type":"ar15.handguard_front","role":"handguard","anchor":"cap_seat","params":{},"flips":false},"handguard_mount":{"type":"ar15.handguard_mount","role":"handguard","anchor":"mount","params":{"nut":"standard"},"flips":false,"note":"On the rifle's own barrel nut: Primary Arms, \"this handguard drops directly onto the existing barrel nut and delta ring\", \"Direct drop in fit, no barrel nut change required\". Placed by the standard's delta ring (rear_x): its instructions, \"make sure your delta ring is securing BOTH upper and lower rear flanges of the Hand Guards\"."},"drop_in":{"type":"ar15.drop_in","role":"handguard","params":{"shape":"round|triangle"},"flips":false,"note":"Magpul (its page, read on the harvested copy): \"Compatible with firearms with delta ring and round or triangular front hand guard retaining caps\": either cap."},"gas_system":{"type":"ar15.gas_system","role":"handguard","params":{"length":"mid"},"flips":false,"note":"Magpul names it \"Mid-Length\" and says it \"Replaces standard AR15/M4 hand guards on mid-length gas systems\"; Primary Arms: \"Gas System Length Mid-Length\"."},"mlok":{"type":"mlok","role":"slots","anchor":"mlok","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_side_slots}","interval":"={std.mlok.interval}","face_distance":"={.mlok_side_face_distance}","reach_inside":"={.reach_inside}"},"faces":{"right_upper":{"angle":"{.mlok_side_face_angle}","note":"Magpul's two o'clock (the rifle's right, +z)"},"left_upper":{"angle":"0 - {.mlok_side_face_angle}","note":"Magpul's ten o'clock"}},"flips":false,"note":"Magpul: \"M-LOK slots at the two, six, and ten o'clock positions for mounting MIL-STD-1913 Picatinny rails or other direct-attach M-LOK accessories\". Three in each, counted on Magpul's and Primary Arms' photos."},"mlok_bottom":{"type":"mlok","role":"slots","anchor":"mlok_bottom","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_bottom_slots}","interval":"={std.mlok.interval}","face_distance":"={.mlok_bottom_face_distance}","reach_inside":"={.reach_inside}"},"faces":{"bottom":{"angle":180,"note":"the underside (Magpul's six o'clock)"}},"flips":false,"note":"Magpul's six o'clock row. No view on file looks at the underside: its count and places are the side rows' (mlok_bottom_slots, assumed), and kept as a gap."}},"materials":{"body":{"label":"Hand guard","finish":"polymer","recolorable":true,"color":"magpul-black","sheen":"satin","options":{"black":{"label":"Black","finish":"polymer","color":"magpul-black","sheen":"satin","sku":"MAG426-BLK","source":"https://magpul.com/moem-lokhandguard-mid-length-ar15-m4.html"},"fde":{"label":"Flat Dark Earth","finish":"polymer","color":"magpul-fde","sheen":"satin","sku":"MAG426-FDE","source":"https://magpul.com/moem-lokhandguard-mid-length-ar15-m4.html"},"odg":{"label":"Olive Drab Green","finish":"polymer","color":"magpul-odg","sheen":"satin","sku":"MAG426-ODG","source":"https://magpul.com/moem-lokhandguard-mid-length-ar15-m4.html"},"gry":{"label":"Stealth Gray","finish":"polymer","color":"magpul-stealth-gray-moe-mlok","sheen":"satin","sku":"MAG426-GRY","source":"https://magpul.com/moem-lokhandguard-mid-length-ar15-m4.html"}},"default":"black","note":"Both halves are one colour in each colourway (Magpul's photos of all four): \"reinforced, heat-resistant Magpul polymer\". Magpul's page names the four (its colour swatches for MAG426: Black, Flat Dark Earth, Olive Drab Green, Stealth Gray); the numbers are Midwest Gun Works' (\"MAG426-BLK Black MAG426-FDE Flat Dark Earth MAG426-GRY Gray MAG426-ODG OD Green\"). Drawn in Magpul's colour presets matched on the MOE SL and the K2+ (data/finishes.yaml); the gray checked against Magpul's own photos of this hand guard in it beside the other three (the report on file: .cache/batch15)."},"heat_shield":{"label":"Heat shield","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"\"The integral, riveted aluminum heat shield\" (Magpul): a bare bright sheet inside the lower half, the same in every colourway (Primary Arms' black one shows it bright through the upper slots, seen across the inside). Drawn in the bright metal finish on file; its alloy and temper aren't stated."}},"components":{},"geometry":{"model":"magpul-moe-mlok-handguard-mid.glb","components":{},"approximations":["Seated at its cap (the cap's `seats`, ar15.handguard_front): its front flange's end at the inside of the cap's face, and its rear end as far into the delta ring as its mounting length then takes it (a tenth of an inch or so on BCM's barrels). The ring is drawn at its forward stop, as the Army's drawing has it with no hand guard in; on the rifle it gives way that much on its spring (std.ar15.slip_ring_front_x), so what this part and the ring share as drawn is hidden inside the ring.","One model of both halves (the seam a groove along each side, seam_y): the two are never apart on a rifle, they come in one box and one colour, and Magpul sells them as one product. The lower one slides into the upper (its instructions) and stands over it along the seam: drawn as the groove only.","Its section about the bore is an assumption past what the photos give (Magpul's width 2.2 in; the top 1.15 and bottom 1.19 from the bore, the slots' height and the seam's from its level photo): a flat underside (bottom_half_width) rounding up into upright sides under the pockets, upright sides to the M-LOK faces, which lean in at the angle the level photo shows the slots at (mlok_side_face_angle, 78° from up; Magpul says two and ten o'clock), a flat for the slots (face_flat), and a round crown (top_half_width). No view on file looks at an end square on.","Its height is the photo's (2.34 in clear of the lip, and 2.38 on the carbine's photo, each scaled by its own M-LOK slots at the standard's pitch); Magpul gives 2.5, which no photo bears out (height). Its width is Magpul's 2.2 in, which no view on file can check.","The plan's narrowing into the delta ring follows the side outline's rounding at the rear (the width shrinks with the height), to its rear end's round collar (rear_collar_od, assumed: a little inside the ring's skirt) in the skirt. The front lower lip runs across the underside to the middle of its rounds.","Inside: the section less a wall of 0.15 in (wall, assumed, set by Magpul's weight at the polymer's density on file: the model weighs about 7.4 oz with its shield against Magpul's 8.7: the inner ribs and bosses no view shows aren't drawn), from a rear wall round the barrel nut to a front wall; ahead of the front wall it is open, over the cap and the front sight base's rear. The front flange that goes into the cap is a round lip on the front wall (front_flange_od, front_flange_length: assumed), as long as Magpul's mounting length says. The gas tube's way through each end is a notch as wide as the delta ring's own.","Three M-LOK slots in each upper side face at the standard's size and pitch, where the level photo has them; the underside's row of three in line with them (assumed: no view on file looks at the underside). Six pockets along each side of the lower half, where the photo has them (their height and depth assumed). The heat shield is a liner of 0.03 in (assumed) inside the lower half, slotted with the underside's row; its rivets aren't drawn (none shows on the mid-length's photos).","Six vents through the crown, where Magpul's Stealth Gray shot from above has them (vent0_x, vent_pitch, carried along the axis by the side slots in the same photo: ± 0.15 in), their width assumed (vent_width).","Edges rounded at 0.02 in (moulded; their size isn't read). The lower half's panels stand in a little from the ribs round them (panel_rib, panel_depth: assumed). Not drawn: the Magpul, M-LOK and MOE marks."],"ledger":["magpul-moe-mlok-handguard-mid.length","magpul-moe-mlok-handguard-mid.width","magpul-moe-mlok-handguard-mid.height","magpul-moe-mlok-handguard-mid.mounting_length","magpul-moe-mlok-handguard-mid.rear_x"]},"profiles":{"side":{"plane":"xy","origin":"its rear edge where it shows ahead of the delta ring's skirt, and its top","offset":{"x":"visible_rear_x","y":"top_above_axis"},"points":[[0,-0.622],[0,-0.72],[0.024,-0.744],[0.024,-1.184],[0.049,-1.208],[0.024,-1.574],[0.049,-1.599],[0.049,-1.77],[0.098,-1.818],[0.098,-2.038],[0.22,-2.16],[0.22,-2.209],[0.293,-2.282],[0.293,-2.307],[0.354,-2.343],[0.378,-2.343],[0.427,-2.294],[0.5,-2.368],[0.574,-2.294],[0.598,-2.319],[0.671,-2.319],[0.696,-2.343],[0.72,-2.319],[0.818,-2.319],[0.867,-2.27],[0.891,-2.294],[1.428,-2.294],[1.477,-2.343],[1.599,-2.343],[1.648,-2.294],[1.672,-2.319],[1.843,-2.319],[1.867,-2.343],[2.038,-2.343],[2.087,-2.294],[2.575,-2.294],[2.648,-2.368],[2.722,-2.368],[2.77,-2.319],[2.868,-2.343],[2.917,-2.294],[2.966,-2.319],[2.99,-2.294],[3.039,-2.343],[3.21,-2.343],[3.259,-2.294],[3.771,-2.294],[3.82,-2.343],[3.893,-2.343],[3.918,-2.319],[3.991,-2.319],[4.04,-2.27],[4.064,-2.294],[4.357,-2.294],[4.406,-2.343],[4.577,-2.343],[4.625,-2.294],[4.747,-2.294],[4.796,-2.343],[4.894,-2.343],[4.918,-2.319],[4.967,-2.319],[4.992,-2.343],[5.358,-2.343],[5.431,-2.294],[5.724,-2.294],[5.773,-2.343],[5.943,-2.343],[6.041,-2.294],[6.066,-2.319],[6.139,-2.319],[6.188,-2.27],[6.212,-2.27],[6.261,-2.319],[6.31,-2.294],[6.334,-2.319],[6.407,-2.319],[6.432,-2.343],[6.529,-2.343],[6.578,-2.294],[6.92,-2.294],[6.944,-2.319],[6.993,-2.294],[7.042,-2.319],[7.091,-2.27],[7.14,-2.319],[7.31,-2.319],[7.335,-2.294],[7.53,-2.294],[7.554,-2.319],[7.701,-2.319],[7.725,-2.343],[7.896,-2.343],[8.03,-2.477],[8.067,-2.563],[8.165,-2.563],[8.177,-2.453],[8.201,-2.429],[8.226,-2.307],[8.275,-2.209],[8.458,-2.026],[8.482,-2.05],[8.506,-2.026],[8.604,-2.026],[8.702,-1.977],[8.799,-1.977],[8.848,-1.953],[9.031,-1.77],[9.031,-1.623],[9.08,-1.574],[9.08,-0.867],[8.934,-0.72],[8.958,-0.696],[8.812,-0.549],[8.812,-0.525],[8.567,-0.256],[8.567,-0.232],[8.555,-0.22],[8.506,-0.244],[8.482,-0.22],[8.433,-0.22],[8.299,-0.085],[8.287,-0.024],[8.213,-0.024],[8.189,0],[7.921,0],[7.896,-0.024],[7.091,-0.024],[7.066,0],[6.725,0],[6.7,-0.024],[0.403,-0.024],[0.098,-0.33],[0.098,-0.354],[0.024,-0.427],[0.024,-0.598]],"scaleRefs":["magpul-moe-mlok-handguard-mid.visible_length"],"inputs":{"magpul-moe-mlok-handguard-mid.visible_length":9.08},"tolerance":0.012,"photo":"references/magpul-moe-mlok-handguard-mid 6dbfde278bf7 (Magpul's feature image 03 for MAG426: the OD green hand guard on a rifle with an A2 front sight base, the rifle's right side seen level, 700 x 525)","method":"saturation > 0.18, inside [128, 135, 530, 275], closing ×5, largest piece, holes filled; scale from magpul-moe-mlok-handguard-mid.visible_length = 9.08 in (x-extent 372 px → 41.0 px/in); origin at x min, y max of the outline; Douglas-Peucker at 0.012 in with the extremes kept: 136 points (IoU 0.999 with the full outline); The outline is the OD green's (saturation over 0.18): the black delta ring and the front sight base are left out. Its scale is Magpul's length less the ring's skirt (visible_length); the three M-LOK slots in the same photo, at the standard's 40 mm pitch, give it within 0.3%.; checks: −y_min in x [1.0, 7.5] 2.368 ± 0.037 in vs magpul-moe-mlok-handguard-mid.height 2.35 ± 0.04 (conflict): agrees; −y_min 2.563 ± 0.037 (tools/trace.py)","via":"harvest","note":"Its M-LOK slots, its pockets and the seam are inside the outline; the model cuts them from the ledger. The front lower lip is the outline's lowest point at its front."}},"gaps":[{"what":"Its underside: the six o'clock M-LOK row's count and places, and the heat shield's rivets","need":"A photo of a MOE M-LOK mid-length from below, its whole underside in frame (a seller's gallery or a review)"},{"what":"Its section square on (how wide the crown and the underside are, how the faces lean) and its width","need":"An end view with a known size in frame, or a photo from above; Magpul publishes no drawing"},{"what":"Its wall and what is inside it (ribs, bosses, the flanges' sizes)","need":"A photo into either end, or of a half alone from inside"},{"what":"Magpul's height, 2.5 in excluding the lip, against the photos' 2.34 to 2.38","need":"What Magpul measured over; a seller's or a reviewer's own measurement"}]},"magpul-moe-plus":{"id":"magpul-moe-plus","name":"MOE+ grip","manufacturer":"Magpul","sku":"MAG416","category":"grip","description":"Magpul's MOE grip with a rubber overmould: the traditional AR-15 lean (Magpul says 25 degrees; its straps average 26 installed), a beavertail that wraps the receiver's tang, ridged straps and a storage cap. Leans about ten degrees more than the MOE-K2+ and hangs 0.65 in less.","weight":"magpul-moe-plus.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"grip_lug":{"origin":["-{.seat_x}",0,0],"note":"Grip frame: origin on the line of its flat top, which bears on the lower's underside, 0.17 in behind where that flat ends as traced (the beavertail's root has begun to rise there). The anchor is the point of that line at the takedown pin's x once installed (seat_x)."}},"interfaces":{"grip_lug":{"type":"ar15.grip_lug","role":"grip","anchor":"grip_lug","params":{},"flips":false}},"materials":{"body":{"label":"Grip","finish":"polymer","recolorable":true,"color":"magpul-black","sheen":"matte","options":{"black":{"label":"Black","finish":"polymer","color":"magpul-black","sheen":"matte","sku":"MAG416-BLK","source":"https://magpul.com/moe-plus-grip-ar15-m4.html"},"fde":{"label":"FDE","finish":"polymer","color":"magpul-fde","sheen":"matte","sku":"MAG416-FDE","source":"https://magpul.com/moe-plus-grip-ar15-m4.html"},"odg":{"label":"ODG","finish":"polymer","color":"magpul-odg","sheen":"matte","sku":"MAG416-ODG","source":"https://magpul.com/moe-plus-grip-ar15-m4.html"},"sgy":{"label":"Stealth Gray","finish":"polymer","color":"magpul-stealth-gray","sheen":"matte","sku":"MAG416-GRY","source":"https://magpul.com/moe-plus-grip-ar15-m4.html"}},"default":"black","note":"Magpul: a rubber overmould on reinforced polymer, with a hard polymer bottom edge. The overmould, drawn as a matte polymer in Magpul's four colours for MAG416 (its page's swatches: Black, Flat Dark Earth, Olive Drab Green, Stealth Gray, each with its number), as matched on the MOE SL's polymer: the rubber's own look isn't separately matched."},"base":{"label":"Bottom edge and cap","finish":"polymer","recolorable":false,"color":"magpul-black","sheen":"matte","note":"Magpul's 'hard polymer bottom edge' and the storage cap in it: black on every colour of grip (its gallery shots 01 and 02 of the FDE one, 01 of the ODG and Stealth Gray ones: references/magpul-moe-plus 0d071645e4b8, 1cce068ee041, aec44baef3c1, c61b35c594de). Drawn as everything below the top of the lip the side outline has round the foot, cut square across (the model's manifest, `base`): on the real grip the black rim is lower than that at the corners and rises mid-side, where the cap latches."}},"components":{"body":{"label":"Grip","material":"body"},"base":{"label":"Bottom edge and cap","material":"base"}},"geometry":{"model":"magpul-moe-plus.glb","components":{},"approximations":["Visual hull of the traced side photo (Primary Arms: the grip lying on its side, turned to its installed lean) and the end section from Magpul's design patent for it (US D600,310 S, FIG. 4). The side is scaled by Magpul's 4.0 in from the receiver to the grip's bottom; the patent's section at that height comes to 1.203 in across, Magpul's 1.2.","The straps are rounded (2026-10-05; until then a slab, both straps flat faces 1.2 in wide) by sections square to the strap's axis, from the same patent sheet: the back strap nearly a full round, as its top plan (FIG. 6) has the heel, arcs of 0.5 in either side of a flat 0.2 in wide; the front strap from where its ribs stop, 0.72 in across in FIG. 4, arcs of 0.24 in. Each strap's ridges, which are in the traced outline, are carried round its corners and run out at the sides.","Assumed in that: the corners are circular arcs and the sides between them flat, where the plan has the grip still widening for an inch ahead of the back strap (up to 0.05 in a side less than drawn); the front strap's ribs are one ridge across its face where FIG. 4 has two columns; the back's round runs out across the shoulder, and the top block, the nose and the beavertail are the two views' hull, their edges broken at 0.03 in. The logo plate and the cap's seam aren't drawn.","The top is cut for the receiver (2026-10-05), as the MOE-K2+'s is: the slot for the standard lug (the Army drawing's faces), as wide as the MOE-K2+'s measures (0.425 in: this grip's own slot isn't measured, and no view of its top with a scale is on file), open at the front; and where the beavertail lies under the receiver, the round of a receiver's rear underside (half-round across as the reference CAD model has it, along the arc of the fullest forging on file, the Workhorse's). Until then it had no slot, and its top stood in the lower's lug. Its nose stands 0.015 in into the trigger guard's ears where the Army's drawing has them and the Workhorse's are, and up to 0.027 into the wall above them (0.006 cubic inches): left as the figures have it (its seat, read on a plain MOE on Aero's lower, is good to 0.055). Until 2026-10-05 the Workhorse's outline had its ears 0.045 further back, and the nose stood 0.06 into them.","Its seat and lean are measured on the plain MOE (MAG415: the same shape by Magpul's figures) on Aero's complete lower, right and left: no pin-framed photo of the MOE+ itself was found. Those two photos differ by 0.11 in on how far down the grip's toe is."],"ledger":["magpul-moe-plus.grip_angle","magpul-moe-plus.bottom_below_lower_underside","magpul-moe-plus.thickness","magpul-moe-plus.overall_height","magpul-moe-plus.toe_y","magpul-moe-plus.seat_x","magpul-moe-plus.lug_slot_width","magpul-moe-plus.back_strap_face_width","magpul-moe-plus.front_strap_face_width","std.ar15.grip_lug_width","std.ar15.grip_lug_face_from_pin","std.ar15.grip_lug_face_angle","std.ar15.grip_lug_depth","std.ar15.grip_seat_below_deck","std.ar15.rear_underside_arc_r_fullest","std.ar15.rear_underside_round_r"]},"profiles":{"side":{"plane":"xy","origin":"on the line of the grip's flat top, which bears on the receiver's underside, 0.17 in behind the flat's rear end as traced (the grip frame origin)","offset":{},"points":[[-1.785,-3.074],[-1.766,-3.143],[-1.694,-3.213],[-1.59,-3.281],[-1.31,-3.427],[-1.141,-3.51],[-1.122,-3.51],[-1.099,-3.49],[-1.067,-3.511],[-1.061,-3.536],[-0.715,-3.701],[-0.508,-3.787],[-0.482,-3.775],[-0.472,-3.785],[-0.472,-3.804],[-0.455,-3.817],[0.036,-4],[0.071,-4],[0.135,-3.969],[0.171,-3.924],[0.209,-3.851],[0.208,-3.767],[0.146,-3.649],[0.137,-3.565],[0.145,-3.523],[1.116,-1.44],[1.161,-1.378],[1.239,-1.314],[1.319,-1.283],[1.411,-1.278],[1.428,-1.265],[1.445,-1.043],[1.457,-0.321],[1.453,-0.214],[1.414,-0.119],[1.35,-0.048],[1.285,-0.011],[1.246,0],[0.176,-0.005],[0.167,0.004],[0.147,0.119],[0.119,0.187],[0.042,0.305],[-0.091,0.447],[-0.203,0.53],[-0.341,0.601],[-0.487,0.646],[-0.605,0.664],[-0.728,0.663],[-0.766,0.647],[-0.798,0.618],[-0.824,0.561],[-0.831,0.519],[-0.83,0.354],[-0.793,0.295],[-0.495,0.063],[-0.425,-0.009],[-0.356,-0.111],[-0.305,-0.233],[-0.281,-0.359],[-0.28,-0.47],[-0.309,-0.604],[-0.347,-0.696],[-0.509,-0.931],[-0.501,-0.965],[-0.55,-0.992],[-0.546,-1.038],[-0.556,-1.048],[-0.592,-1.054],[-0.603,-1.077],[-0.595,-1.107],[-0.641,-1.127],[-0.648,-1.153],[-0.641,-1.172],[-0.69,-1.2],[-0.686,-1.242],[-0.731,-1.265],[-0.739,-1.288],[-0.731,-1.307],[-0.773,-1.327],[-0.784,-1.353],[-0.776,-1.376],[-0.818,-1.396],[-0.829,-1.419],[-0.822,-1.445],[-0.86,-1.465],[-0.871,-1.484],[-0.867,-1.515],[-0.905,-1.534],[-0.916,-1.565],[-0.912,-1.584],[-0.95,-1.603],[-0.957,-1.649],[-0.999,-1.684],[-0.999,-1.718],[-1.033,-1.738],[-1.044,-1.757],[-1.044,-1.791],[-1.069,-1.801],[-1.086,-1.822],[-1.085,-1.86],[-1.12,-1.876],[-1.131,-1.899],[-1.131,-1.926],[-1.172,-1.964],[-1.172,-1.999],[-1.206,-2.022],[-1.217,-2.068],[-1.251,-2.099],[-1.259,-2.141],[-1.289,-2.164],[-1.3,-2.21],[-1.334,-2.241],[-1.341,-2.283],[-1.372,-2.306],[-1.379,-2.352],[-1.409,-2.375],[-1.42,-2.425],[-1.451,-2.448],[-1.462,-2.498],[-1.492,-2.521],[-1.503,-2.571],[-1.533,-2.598],[-1.541,-2.64],[-1.567,-2.66],[-1.582,-2.713],[-1.609,-2.736],[-1.62,-2.782],[-1.646,-2.806],[-1.657,-2.855],[-1.699,-2.89],[-1.744,-2.967],[-1.774,-3.028]],"scaleRefs":["magpul-moe-plus.bottom_below_lower_underside"],"angleRef":"magpul-moe-plus.grip_angle","inputs":{"magpul-moe-plus.bottom_below_lower_underside":4,"magpul-moe-plus.grip_angle":26.282},"tolerance":0.006,"photo":"references/magpul-moe-plus b9c00c3d5081 (Primary Arms MAG416-BLK_00.jpg: the MOE+ alone on white, straight right side, 2000 x 1334)","method":"luminance < 200, closing ×2, largest piece, holes filled; rotated +0.5° (counter-clockwise) so the edges' mean lean in the band 0.45–0.85 of the height (27.7° rear, 25.5° front in the photo) becomes magpul-moe-plus.grip_angle = 26.282°; re-measured 27.6°/25.0°; scale from magpul-moe-plus.bottom_below_lower_underside = 4 in (y from the origin to the far edge 1047 px → 261.7 px/in); origin at the rear end of the flat top; Douglas-Peucker at 0.006 in with the extremes kept: 133 points (IoU 0.997 with the full outline) (tools/trace.py)","via":"harvest","note":"Includes the beavertail (above the flat top; it wraps the receiver's tang) and the nose behind the trigger guard. The straps' ridges are in the outline; the overmould's texture and the logo plate aren't."},"front":{"plane":"zy","origin":"the toe (lowest point), centred; offset to the side profile's toe","offset":{"y":"toe_y"},"points":[[-0.601,2.919],[-0.601,0.548],[-0.557,0.436],[-0.548,0.275],[-0.346,0.019],[-0.297,0.005],[0,0],[0.088,0],[0.341,0.015],[0.514,0.222],[0.557,0.295],[0.557,0.421],[0.601,0.557],[0.601,2.919],[0.562,3.138],[0.48,3.367],[0.441,3.552],[0.431,4.652],[0.355,4.664],[0.263,4.576],[0.185,4.533],[0.083,4.498],[-0.015,4.489],[-0.175,4.528],[-0.278,4.591],[-0.346,4.659],[-0.404,4.664],[-0.436,4.627],[-0.441,3.532],[-0.475,3.367],[-0.528,3.24],[-0.587,3.035]],"scaleRefs":["magpul-moe-plus.overall_height"],"inputs":{"magpul-moe-plus.overall_height":4.664},"tolerance":0.01,"photo":"references/magpul-moe-plus bd5d1a90cef0 (US D600,310 S (Magpul MOE+), FIG. 4 front elevation, 300 dpi)","method":"luminance < 128, inside [330, 2600, 1360, 2960], closing ×3, largest piece, holes filled, inset 2 px (half the outline's stroke); rotated -90.0° as declared; scale from magpul-moe-plus.overall_height = 4.664 in (y-extent 958 px → 205.4 px/in); origin at x center, y min of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 32 points (IoU 0.997 with the full outline) (tools/trace.py)","via":"harvest","note":"The sheet has the figure turned a quarter (the beavertail at the left). Seen from the front, so its right is the grip's left; the outline is symmetric."}},"gaps":[{"what":"Its lug slot's width measured on an MOE+ (it is drawn at the MOE-K2+'s)","need":"a view of an MOE+'s top from above with a scale, or the slot against the top's width in one"},{"what":"Its seat, lean and drop measured on the MOE+ itself (they are the plain MOE's)","need":"a straight side photo of an MOE+ on a lower with the receiver's pins in view"},{"what":"The black rim's own line round the foot (lower at the corners, rising mid-side where the cap latches) and the logo plate as their own surfaces","need":"a straight side photo of a coloured MOE+ at a known scale: the base is cut square across at the top of the lip meanwhile"}]},"magpul-moe-sl-carbine":{"id":"magpul-moe-sl-carbine","name":"MOE SL carbine stock, mil-spec","manufacturer":"Magpul","sku":"MAG347","category":"stock","weight":"magpul-moe-sl-carbine.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"butt":{"origin":[0,0,0],"note":"The butt's plane on the tube axis: the part frame's origin. Overall length and length of pull end here."},"tube":{"origin":["{.butt_behind_pin_pos1}",0,0],"x":[-1,0,0],"note":"Stock frame: origin on the tube axis in the plane of the butt, +x forward. At position 1 this anchor sits at the takedown pin's X."}},"interfaces":{"tube":{"type":"receiver_extension","role":"stock","anchor":"tube","params":{"profile":"mil-spec"},"flips":false}},"materials":{"body":{"label":"Stock body","finish":"polymer","recolorable":true,"color":"magpul-black","sheen":"satin","options":{"black":{"label":"Black","finish":"polymer","color":"magpul-black","sheen":"satin","sku":"MAG347-BLK","source":"https://magpul.com/moe-sl-carbine-stock-mil-spec.html"},"fde":{"label":"FDE","finish":"polymer","color":"magpul-fde","sheen":"satin","sku":"MAG347-FDE","source":"https://magpul.com/moe-sl-carbine-stock-mil-spec.html"},"odg":{"label":"ODG","finish":"polymer","color":"magpul-odg","sheen":"satin","sku":"MAG347-ODG","source":"https://magpul.com/moe-sl-carbine-stock-mil-spec.html"},"sgy":{"label":"Stealth Gray","finish":"polymer","color":"magpul-stealth-gray","sheen":"satin","sku":"MAG347-GRY","source":"https://magpul.com/moe-sl-carbine-stock-mil-spec.html"}},"default":"black","note":"The four colours Magpul's page offers MAG347 in (its swatches: Black, Flat Dark Earth, Olive Drab Green, Stealth Gray, each with its number), the colours matched on this stock. In every colour the release latch is the body's colour, as drawn (Magpul's gallery shots 03 of the FDE, ODG and Stealth Gray ones: references/magpul-moe-sl-carbine cdd8efea5595, 459712a8f3b5, 10dbd0585651). What stays black on every colour: the lock pin's head and the QD socket's steel cup, drawn since 2026-10-13 in the pad's black (the part has no slot for black steel, so their finish is the pad's rubber), and the latch's pivot pin, which isn't drawn."},"buttpad":{"label":"Buttpad","finish":"rubber","recolorable":false,"color":"magpul-black","note":"Black rubber on every colour of stock (Magpul's gallery shots 03 of the FDE, ODG and Stealth Gray ones). The lock pin's two heads and the QD socket's liner are drawn in this slot as well: black steel on every colour (cdd8efea5595, 78e4583631dd), for want of a slot of their own."}},"components":{"body":{"label":"Stock body","material":"body"},"buttpad":{"label":"Buttpad","material":"buttpad"}},"geometry":{"model":"magpul-moe-sl-carbine.glb","components":{},"approximations":["Visual hull of the traced side photo and the end section from Magpul's design patent (US D736,336 S, FIG. 7, scaled by the published 5.3 × 1.7 in, which fit it with one scale): the section holds along the stock wherever the side view shows it (the patent's plan view stays 1.71–1.72 wide over 20–90% of the length, 1.63 near the butt).","The side pockets cut to the brace-and-floor width the patent's front view bounds (profiles.web) within the region the side photo shows them; the three through-holes cut; the rubber butt pad its own part behind its seam, with its ribs. Inside the frame the floors lie in by one depth (0.05 in, from the frame's shadow on the triangle's floor and from the patent's front view; no view is square across a floor): the pocket's floor behind the lock pin's housing, the one ahead of it and the triangle under the QD socket, with the small block by the butt left standing and a groove of that depth round the socket's ring. The release latch stands in the pockets as its pieces (2026-10-13), each outlined on the side photo and out to where the patent's bottom plan (FIG. 9) puts its face: the lever, a long triangle from its tip to the round boss it pivots on, and its front arm (0.477 from the middle; the boss 0.512); the grip, a wedge out to 0.655 whose ridged face slopes back in to the wall, with the twelve ridges two photos count, 0.082 in apart (each drawn half that wide and 0.023 in high, as their ends stand in profile: their section isn't read). The lock pin's head stands each side in its upright slot (0.19 in across, out to 0.59 from the middle; the slot's upper end is behind the head and is drawn 0.02 in above it), and the QD socket is a ring at the frame's own face (0.62 in across; how far it stands isn't read) round a bore of 0.43 in with its steel cup as a liner. The pin's heads and the liner are drawn in the pad's black, which they are on every colour of stock: the part has no slot for black steel. Edges broken at 0.03 in (the grip's at 0.012, its ridges' not).","Bored from its front for the receiver extension, a keyhole: the bore at 1.163 in, the larger of the two hidden circles on the patent's front view (± 0.03, which spans the other, 1.136), one diameter all the way; under it the indexing rail's channel at the rail's own width and depth (0.49 in, to 0.874 in below the axis), with nothing to spare: no clearance is known, and the patent's front view hasn't been read for it. It ends where the tube's rear end reaches with the stock collapsed (the buffer kit's tube); the real bore's end and its mouth's flare aren't sourced. The channel runs over the latch's arm, inside the stock."],"ledger":["magpul-moe-sl-carbine.length","magpul-moe-sl-carbine.height","magpul-moe-sl-carbine.width","magpul-moe-sl-carbine.tube_axis_below_top","magpul-moe-sl-carbine.latch_tab_half_width","magpul-moe-sl-carbine.latch_boss_half_width","magpul-moe-sl-carbine.butt_behind_pin_pos1","magpul-moe-sl-carbine.bore_diameter","magpul-moe-sl-carbine.rail_channel_width","magpul-moe-sl-carbine.rail_channel_floor_below_axis","magpul-moe-sl-carbine.latch_arm_half_width","magpul-moe-sl-carbine.panel_recess_depth","magpul-moe-sl-carbine.grip_teeth","magpul-moe-sl-carbine.grip_tooth_pitch","magpul-moe-sl-carbine.grip_first_tooth","magpul-moe-sl-carbine.grip_tooth_height","magpul-moe-sl-carbine.grip_edge_height","magpul-moe-sl-carbine.grip_foot_half_width","magpul-moe-sl-carbine.lock_slot_floor_half_width","magpul-moe-sl-carbine.lock_pin_face_half_width"]},"profiles":{"side":{"plane":"xy","origin":"rearmost point of the butt pad (x) and the top edge (y); the photo shows the top level, so the tube axis is horizontal","offset":{"y":"tube_axis_below_top"},"points":[[0,-0.69],[0.049,-0.76],[0.046,-0.803],[0.012,-0.852],[0.012,-0.904],[0.064,-0.977],[0.058,-1.023],[0.024,-1.065],[0.024,-1.117],[0.079,-1.175],[0.04,-1.3],[0.094,-1.382],[0.091,-1.431],[0.058,-1.477],[0.055,-1.522],[0.11,-1.589],[0.104,-1.641],[0.07,-1.681],[0.07,-1.727],[0.122,-1.784],[0.128,-1.827],[0.085,-1.885],[0.088,-1.946],[0.137,-1.992],[0.131,-2.053],[0.098,-2.105],[0.101,-2.141],[0.155,-2.205],[0.155,-2.242],[0.113,-2.306],[0.113,-2.342],[0.171,-2.418],[0.165,-2.464],[0.128,-2.516],[0.131,-2.562],[0.186,-2.629],[0.183,-2.665],[0.143,-2.726],[0.143,-2.763],[0.198,-2.836],[0.195,-2.879],[0.155,-2.937],[0.158,-2.982],[0.213,-3.052],[0.207,-3.092],[0.171,-3.141],[0.171,-3.18],[0.229,-3.254],[0.222,-3.302],[0.186,-3.351],[0.186,-3.403],[0.238,-3.464],[0.232,-3.519],[0.192,-3.567],[0.204,-3.625],[0.253,-3.683],[0.25,-3.72],[0.21,-3.778],[0.21,-3.82],[0.268,-3.9],[0.259,-3.948],[0.222,-3.985],[0.222,-4.015],[0.232,-4.052],[0.28,-4.116],[0.265,-4.168],[0.238,-4.198],[0.241,-4.25],[0.296,-4.326],[0.29,-4.372],[0.259,-4.409],[0.268,-4.482],[0.475,-5.04],[0.536,-5.158],[0.629,-5.227],[0.989,-5.261],[1.026,-5.245],[1.309,-5.236],[1.382,-5.203],[1.439,-5.149],[2.774,-3.077],[2.85,-2.97],[2.927,-2.902],[3.055,-2.859],[4.844,-2.612],[5.14,-2.609],[5.213,-2.563],[6.649,-2.371],[6.746,-2.347],[6.829,-2.301],[6.906,-2.233],[6.983,-2.135],[7.287,-1.586],[7.327,-1.355],[7.354,-0.687],[7.3,-0.178],[7.272,-0.084],[7.204,-0.021],[0.995,-0.034],[0.684,-0.03],[0.623,-0.003],[0.468,0],[0.169,-0.03],[0.085,-0.102],[0.049,-0.163],[0.061,-0.227],[0.018,-0.297],[0.049,-0.404],[0.012,-0.459],[0.006,-0.498],[0.049,-0.587],[0.006,-0.651]],"features":{"through":[[[1.103,-1.812],[1.119,-1.763],[1.181,-1.731],[2.293,-1.728],[2.329,-1.754],[2.325,-1.824],[2.29,-1.865],[2.236,-1.877],[1.151,-1.877],[1.112,-1.855]],[[1.335,-2.421],[1.344,-2.339],[1.387,-2.254],[1.434,-2.21],[1.495,-2.188],[1.577,-2.191],[1.62,-2.207],[1.655,-2.245],[1.67,-2.29],[1.667,-2.367],[1.602,-2.478],[1.492,-2.533],[1.422,-2.524],[1.356,-2.476]],[[1.161,-4.732],[1.173,-4.695],[1.777,-3.759],[1.824,-3.724],[1.891,-3.731],[1.929,-3.787],[1.917,-3.86],[1.317,-4.802],[1.248,-4.84],[1.199,-4.828],[1.17,-4.799]]],"buttpad":[[[-0.139,0.142],[0.334,0.142],[0.73,-5.405],[-0.139,-5.405]]],"latch":[[[2.415,-1.986],[3.458,-1.809],[4.189,-1.449],[4.372,-1.397],[4.372,-1.855],[4.189,-1.885],[3.519,-2.022],[2.458,-2.229]]],"latch_boss":[[[4.592,-1.602],[4.584,-1.658],[4.562,-1.711],[4.527,-1.757],[4.482,-1.792],[4.429,-1.813],[4.372,-1.821],[4.315,-1.813],[4.262,-1.792],[4.217,-1.757],[4.182,-1.711],[4.16,-1.658],[4.153,-1.602],[4.16,-1.545],[4.182,-1.492],[4.217,-1.446],[4.262,-1.411],[4.315,-1.39],[4.372,-1.382],[4.429,-1.39],[4.482,-1.411],[4.527,-1.446],[4.562,-1.492],[4.584,-1.545]]],"pocket":[[[0.806,-1.245],[2.94,-1.306],[5.987,-1.382],[6.902,-1.413],[6.963,-1.717],[6.597,-2.327],[6.597,-5.68],[1.172,-5.68],[1.141,-5.07],[1.05,-4.156],[0.806,-1.717]]],"grip":[[[2.428,-1.961],[3.464,-1.784],[3.5,-2.041],[2.44,-2.223]]],"lever":[[[2.863,-1.535],[3.808,-1.385],[4.235,-1.379],[4.372,-1.379],[4.372,-1.827],[4.281,-1.83],[3.915,-1.861],[3.503,-1.943],[3.397,-1.9],[3.244,-1.839],[3.092,-1.717]],[[4.372,-1.379],[4.844,-1.367],[4.844,-1.486],[4.372,-1.504]]],"lock_slot":[[[4.985,-1.461],[5.009,-1.437],[5.195,-1.437],[5.219,-1.461],[5.219,-1.945],[5.21,-1.99],[5.184,-2.028],[5.147,-2.053],[5.102,-2.062],[5.058,-2.053],[5.02,-2.028],[4.994,-1.99],[4.985,-1.945]]],"lock_pin":[[[5.23,-1.548],[5.225,-1.577],[5.212,-1.603],[5.192,-1.624],[5.166,-1.637],[5.137,-1.641],[5.108,-1.637],[5.083,-1.624],[5.062,-1.603],[5.049,-1.577],[5.044,-1.548],[5.049,-1.52],[5.062,-1.494],[5.083,-1.473],[5.108,-1.46],[5.137,-1.455],[5.166,-1.46],[5.192,-1.473],[5.212,-1.494],[5.225,-1.52]]],"qd":[[[1.675,-2.335],[1.671,-2.372],[1.66,-2.409],[1.642,-2.442],[1.618,-2.471],[1.589,-2.496],[1.555,-2.514],[1.519,-2.525],[1.481,-2.528],[1.443,-2.525],[1.407,-2.514],[1.374,-2.496],[1.344,-2.471],[1.32,-2.442],[1.302,-2.409],[1.291,-2.372],[1.288,-2.335],[1.291,-2.297],[1.302,-2.261],[1.32,-2.227],[1.344,-2.198],[1.374,-2.174],[1.407,-2.156],[1.443,-2.145],[1.481,-2.141],[1.519,-2.145],[1.555,-2.156],[1.589,-2.174],[1.618,-2.198],[1.642,-2.227],[1.66,-2.261],[1.671,-2.297]],[[1.695,-2.335],[1.691,-2.376],[1.678,-2.416],[1.659,-2.453],[1.632,-2.485],[1.6,-2.512],[1.563,-2.532],[1.523,-2.544],[1.481,-2.548],[1.439,-2.544],[1.4,-2.532],[1.363,-2.512],[1.33,-2.485],[1.304,-2.453],[1.284,-2.416],[1.272,-2.376],[1.268,-2.335],[1.272,-2.293],[1.284,-2.253],[1.304,-2.216],[1.33,-2.184],[1.363,-2.157],[1.4,-2.137],[1.439,-2.125],[1.481,-2.121],[1.523,-2.125],[1.563,-2.137],[1.6,-2.157],[1.632,-2.184],[1.659,-2.216],[1.678,-2.253],[1.691,-2.293]],[[1.792,-2.335],[1.786,-2.395],[1.768,-2.453],[1.74,-2.507],[1.701,-2.554],[1.654,-2.593],[1.6,-2.622],[1.542,-2.639],[1.481,-2.646],[1.421,-2.639],[1.362,-2.622],[1.308,-2.593],[1.261,-2.554],[1.223,-2.507],[1.194,-2.453],[1.176,-2.395],[1.17,-2.335],[1.176,-2.274],[1.194,-2.216],[1.223,-2.162],[1.261,-2.115],[1.308,-2.076],[1.362,-2.048],[1.421,-2.03],[1.481,-2.024],[1.542,-2.03],[1.6,-2.048],[1.654,-2.076],[1.701,-2.115],[1.74,-2.162],[1.768,-2.216],[1.786,-2.274]],[[1.841,-2.335],[1.834,-2.405],[1.813,-2.472],[1.78,-2.535],[1.735,-2.589],[1.681,-2.634],[1.619,-2.667],[1.551,-2.687],[1.481,-2.694],[1.411,-2.687],[1.343,-2.667],[1.281,-2.634],[1.227,-2.589],[1.182,-2.535],[1.149,-2.472],[1.129,-2.405],[1.122,-2.335],[1.129,-2.265],[1.149,-2.197],[1.182,-2.135],[1.227,-2.08],[1.281,-2.036],[1.343,-2.002],[1.411,-1.982],[1.481,-1.975],[1.551,-1.982],[1.619,-2.002],[1.681,-2.036],[1.735,-2.08],[1.78,-2.135],[1.813,-2.197],[1.834,-2.265]]],"panel":[[[1.065,-1.169],[4.844,-1.169],[4.844,-2.318],[3.702,-2.498],[2.94,-2.613],[2.818,-2.61],[2.635,-2.546],[2.33,-2.434],[1.83,-2.245],[1.776,-2.128],[1.688,-2.04],[1.574,-1.987],[1.481,-1.975],[1.388,-1.987],[1.301,-2.023],[1.226,-2.082],[1.065,-2.034]],[[5.405,-1.169],[7.152,-1.169],[6.627,-2.071],[5.405,-2.248]],[[0.837,-2.175],[1.133,-2.247],[1.127,-2.397],[1.17,-2.514],[1.25,-2.61],[1.358,-2.673],[1.481,-2.694],[1.604,-2.673],[1.712,-2.61],[1.802,-2.498],[1.964,-2.54],[2.421,-2.647],[2.574,-2.708],[2.62,-2.784],[2.33,-3.287],[2.086,-3.683],[1.888,-3.805],[1.233,-4.765],[1.248,-4.933],[1.157,-4.887],[1.087,-4.765],[1.01,-4.339],[0.913,-2.967]]],"tab":[[[0.867,-3.851],[1.279,-3.851],[1.279,-4.049],[0.867,-4.049]]]},"scaleRefs":["magpul-moe-sl-carbine.length","magpul-moe-sl-carbine.height"],"inputs":{"magpul-moe-sl-carbine.height":5.3,"magpul-moe-sl-carbine.length":7.3},"tolerance":0.01,"photo":"references/magpul-moe-sl-carbine 9b34a5d996e8 (MOE SL, straight side view on white, 2485 px; supplied by the user from their downloads, source not recorded)","method":"luminance < 235, closing ×2, largest piece, holes filled; scale from magpul-moe-sl-carbine.length = 7.3 in (x-extent 2413 px → 330.5 px/in) and magpul-moe-sl-carbine.height = 5.3 in (y-extent 1726 px → 325.7 px/in), which agree within 1.5%; mean 328.1 px/in; origin at x min, y max of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 112 points (IoU 0.998 with the full outline); the butt pad's ribs kept (M5 detail pass; M3 filled them to their tips' envelope): the rearmost tip still sets the butt plane; features through the same placement (through: reviewed pixel boxes; buttpad: reviewed pixel boxes; latch: reviewed pixel boxes; latch_boss: reviewed pixel boxes; pocket: reviewed pixel boxes; grip: reviewed pixel boxes; lever: reviewed pixel boxes; lock_slot: reviewed pixel boxes; lock_pin: reviewed pixel boxes; qd: reviewed pixel boxes; panel: reviewed pixel boxes; tab: reviewed pixel boxes) (tools/trace.py)","via":"user","note":"Thickness is the published maximum width; the end section comes from Magpul's patent (end). The side's recessed panel, latch and QD cup aren't in the outline."},"front":{"plane":"zy","origin":"the top edge, centred: as the side profile, offset down to the tube axis","offset":{"y":"tube_axis_below_top"},"points":[[-0.85,-1.1],[-0.84,-1.328],[-0.785,-1.448],[-0.778,-1.51],[-0.691,-4.139],[-0.661,-4.399],[-0.457,-5.124],[-0.431,-5.176],[-0.371,-5.239],[-0.306,-5.275],[0.013,-5.301],[0.296,-5.278],[0.361,-5.246],[0.434,-5.169],[0.473,-5.075],[0.665,-4.386],[0.694,-4.103],[0.782,-1.471],[0.843,-1.318],[0.85,-1.051],[0.811,-0.931],[0.782,-0.759],[0.678,-0.473],[0.629,-0.366],[0.554,-0.258],[0.426,-0.137],[0.296,-0.062],[0.14,-0.013],[-0.002,-0.002],[-0.007,0],[-0.163,-0.02],[-0.312,-0.072],[-0.445,-0.153],[-0.57,-0.281],[-0.665,-0.444],[-0.782,-0.765],[-0.801,-0.912],[-0.843,-1.016]],"scaleRefs":["magpul-moe-sl-carbine.height","magpul-moe-sl-carbine.width"],"inputs":{"magpul-moe-sl-carbine.height":5.3,"magpul-moe-sl-carbine.width":1.7},"tolerance":0.01,"photo":"references/magpul-moe-sl-carbine 505db255225b (US D736,336 S (Magpul), FIG. 7 front elevation, 300 dpi)","method":"luminance < 128, inside [1380, 820, 1950, 2530], closing ×3, largest piece, holes filled, inset 2 px (half the outline's stroke); scale from magpul-moe-sl-carbine.height = 5.3 in (y-extent 1631 px → 307.7 px/in) and magpul-moe-sl-carbine.width = 1.7 in (x-extent 523 px → 307.6 px/in), which agree within 0.0%; mean 307.7 px/in; origin at x center, y max of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 38 points (IoU 0.996 with the full outline) (tools/trace.py)","via":"harvest","note":"Seen from the front, so its right is the stock's left; the outline is symmetric. The release latch stands out of both sides at mid-height."},"web":{"plane":"zy","origin":"the stock's top edge, centred (as the end section); offset down to the tube axis","offset":{"y":"tube_axis_below_top"},"points":[[-0.457,-2.206],[-0.408,-2.392],[-0.388,-2.583],[-0.375,-3.022],[-0.349,-3.376],[-0.343,-3.623],[-0.31,-4.166],[-0.304,-4.423],[-0.278,-4.777],[-0.278,-5.401],[0.279,-5.402],[0.281,-4.767],[0.317,-4.163],[0.343,-3.578],[0.359,-3.363],[0.372,-3.035],[0.388,-2.824],[0.388,-2.583],[0.408,-2.395],[0.46,-2.203],[0.46,-1.199],[-0.455,-1.197]],"scaleRefs":["magpul-moe-sl-carbine.height"],"inputs":{"magpul-moe-sl-carbine.height":5.3},"tolerance":0.004,"photo":"references/magpul-moe-sl-carbine 505db255225b (US D736,336 S (Magpul), FIG. 7: the brace and pocket floor's width, row by row)","method":"manual polygon (32 points picked on the photo); frame from the reviewed holes top, bottom (307.7 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.004 in with the extremes kept: 22 points (IoU 0.997 with the full outline) (tools/trace.py)","via":"harvest","note":"Whether these lines are the brace's sides or the pocket floor's planes, nothing below the cheek and in front of the butt is wider: the pockets are drawn to that depth."}},"gaps":[{"what":"The step along the pocket 0.37 in under the cheek's edge: on the side photo a lit band with a shadow 0.14 in high under it, the length of the pocket. Not drawn: the pocket's wall is one plane from the cheek's edge down.","need":"A close view from the front quarter or from below that shows which side of the step stands proud, and by how much."},{"what":"How deep the floors inside the frame lie (drawn 0.05 in, from a shadow and from the patent's front view), whether the three are one depth, and how far the QD socket's ring stands from the frame (drawn at the frame's face).","need":"A view along a floor's edge, or a section; the ring from below or from the front quarter, close."},{"what":"The grip's ridges in section, and whether the band over them on the side photo (0.04 in high) is an upright edge, as drawn, or the grip's upper face seen from a little above. The patent draws an upright end 0.1 in high.","need":"A close view of the grip from its end or from below."},{"what":"The latch's hook round the lock pin, the housing the pin's slot is in (the patent's bottom plan draws the stock 0.72 in from the middle each side between 4.4 and 5.2 in ahead of the butt, which nothing on the side photo was matched to), the pivot's black pin in its boss (seen on the left side only) and the small screw in the frame under the lock pin (0.08 in across).","need":"A close view of the slot and the boss from each side; the screw and the pivot pin are on the photos on file and wait for a slot for black steel."}]},"magpul-moe-sl-handguard-carbine":{"id":"magpul-moe-sl-handguard-carbine","name":"MOE SL® Hand Guard, Carbine-Length – AR15/M4","manufacturer":"Magpul","sku":"MAG538","url":"https://magpul.com/moeslhandguard-carbine-length-ar15-m4.html","category":"handguard","description":"Magpul's slim polymer drop-in hand guard for a carbine-length gas system and an A2 front sight, in two halves: \"Replaces standard AR15/M4 hand guards on carbine-length gas systems\"; \"Narrow cross section reduces weight and bulk\"; \"M-LOK slots at the two, six, and ten o'clock positions\"; \"The integral, riveted aluminum heat shield, combined with the front lower lip and side extensions, shields the support hand from a hot gas block\"; \"Front lip and long side extensions shields hand from hot sight assembly\"; \"Made in the USA\" (Magpul). It goes on the rifle's own barrel nut and delta ring and the round cap behind its A2 front sight base: no free-float nut of its own.","weight":"magpul-moe-sl-handguard-carbine.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[{"slot":"gas_block","parts":["bcm-front-sight-base-f-750"],"says":"Magpul, MOE SL Hand Guard, Carbine-Length: \"Only compatible with firearms that include an A2 front sight assembly and a round front hand guard retaining cap.\"; \"*Must be used with the A2 front sight assembly, other gas blocks are not compatible. Factory sling swivel is not compatible and, if equipped, must be removed from the A2 front sight assembly.\"; \"Not compatible with piston operated AR platforms.\"","source":"https://magpul.com/moeslhandguard-carbine-length-ar15-m4.html"}],"needs":{"slots":["barrel_nut","delta_ring","handguard_cap"],"says":"Magpul: \"Compatible with firearms with an A2 front sight assembly, a round front hand guard retaining cap, and rear spring-loaded delta ring\"; its instructions: \"Slide the front flange of the Upper Hand Guard piece into the metal hand guard cap, located behind the front sight base/gas block\" and \"make sure your delta ring is securing BOTH upper and lower rear flanges of the Hand Guards\".","source":"https://magpul.com/moeslhandguard-carbine-length-ar15-m4.html"},"anchors":{"mount":{"origin":["0in - {.rear_x}",0,0],"note":"The receiver's front face on the bore axis, +x toward the muzzle: its rear flanges stand in the delta ring's skirt against the ring's lip (std.ar15.slip_ring_front_x ahead of the receiver)."},"mlok":{"origin":["{.mlok_side_slot0_x}","{.mlok_axis_y}",0],"note":"At the upper side faces' rearmost M-LOK slot's centre (index 0), +x toward the muzzle, on the axis the faces' normals through their slots' centres meet (mlok_axis_y, above the bore): the faces are angles about this axis."},"mlok_bottom":{"origin":["{.mlok_bottom_slot0_x}",0,0],"note":"The same axis at the underside's rearmost slot's centre (read from below, in line with the side rows')."},"cap_seat":{"origin":["{.mounting_length}",0,0],"note":"The front flange's front end, on the bore axis: what goes into the round hand guard cap (Magpul's mounting length ahead of its rear flanges' end)."}},"interfaces":{"cap_seat":{"type":"ar15.handguard_front","role":"handguard","anchor":"cap_seat","params":{},"flips":false},"handguard_mount":{"type":"ar15.handguard_mount","role":"handguard","anchor":"mount","params":{"nut":"standard"},"flips":false,"note":"On the rifle's own barrel nut and delta ring: Magpul, \"Easy to install utilizing existing delta ring and round front hand guard retaining cap with A2 front sight assembly*\". Placed by the standard's delta ring (rear_x): its instructions, \"make sure your delta ring is securing BOTH upper and lower rear flanges of the Hand Guards\"."},"drop_in":{"type":"ar15.drop_in","role":"handguard","params":{"shape":"round"},"flips":false,"note":"Magpul (its page, read on the harvested copy): \"Only compatible with firearms that include an A2 front sight assembly and a round front hand guard retaining cap.\"; \"a direct replacement for M4 Carbine-type plastic, two-piece hand guards and utilizes the existing round front hand guard retaining cap and rear spring-loaded delta ring\". Primary Arms: \"Not compatible with triangular retaining caps or non-A2 gas blocks.\""},"gas_system":{"type":"ar15.gas_system","role":"handguard","params":{"length":"carbine"},"flips":false,"note":"Magpul names it \"Carbine-Length\": \"Replaces standard AR15/M4 hand guards on carbine-length gas systems\", \"Compatibility Firearms with carbine-length gas systems and an A2 front sight.\"; Primary Arms: \"Gas System Length Carbine\"."},"mlok":{"type":"mlok","role":"slots","anchor":"mlok","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_side_slots}","interval":"={std.mlok.interval}","face_distance":"={.mlok_side_face_distance}","reach_inside":"={.reach_inside}"},"faces":{"right_upper":{"angle":"{.mlok_side_face_angle}","note":"Magpul's two o'clock (the rifle's right, +z)"},"left_upper":{"angle":"0 - {.mlok_side_face_angle}","note":"Magpul's ten o'clock"}},"flips":false,"note":"Magpul: \"M-LOK slots at the two, six, and ten o'clock positions for mounting MIL-STD-1913 Picatinny rails or other direct-attach M-LOK accessories\". Three in each, counted on Magpul's and Primary Arms' photos and its instruction sheet's drawing."},"mlok_bottom":{"type":"mlok","role":"slots","anchor":"mlok_bottom","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_bottom_slots}","interval":"={std.mlok.interval}","face_distance":"={.mlok_bottom_face_distance}","reach_inside":"={.reach_inside}"},"faces":{"bottom":{"angle":180,"note":"the underside (Magpul's six o'clock)"}},"flips":false,"note":"Magpul's six o'clock row: four openings at the M-LOK pitch on Magpul's photo of the gray one from below (d4a119f9380f), the fourth a short one with the heat shield showing in it."}},"materials":{"body":{"label":"Hand guard","finish":"polymer","recolorable":true,"color":"magpul-black","sheen":"satin","options":{"black":{"label":"Black","finish":"polymer","color":"magpul-black","sheen":"satin","sku":"MAG538-BLK","source":"https://magpul.com/moeslhandguard-carbine-length-ar15-m4.html"},"fde":{"label":"Flat Dark Earth","finish":"polymer","color":"magpul-fde","sheen":"satin","sku":"MAG538-FDE","source":"https://magpul.com/moeslhandguard-carbine-length-ar15-m4.html"},"odg":{"label":"Olive Drab Green","finish":"polymer","color":"magpul-odg","sheen":"satin","sku":"MAG538-ODG","source":"https://magpul.com/moeslhandguard-carbine-length-ar15-m4.html"},"gry":{"label":"Stealth Gray","finish":"polymer","color":"magpul-stealth-gray-moe-mlok","sheen":"satin","sku":"MAG538-GRY","source":"https://magpul.com/moeslhandguard-carbine-length-ar15-m4.html"}},"default":"black","note":"Both halves are one colour in each colourway (Magpul's gallery shots of all four, and Primary Arms' photograph of the gray): \"reinforced, heat-resistant Magpul polymer\"; Primary Arms: \"Finish Matte\". Magpul's page names the four (its colour swatches for MAG538: Black, Flat Dark Earth, Olive Drab Green, Stealth Gray); the numbers are Midwest Gun Works' (\"MAG538-BLK Black MAG538-FDE Flat Dark Earth MAG538-GRY Gray MAG538-ODG OD Green\") and Primary Arms' (\"MAG538-GRY\", \"Color Grey\"). The gray is drawn in `magpul-stealth-gray-moe-mlok`, the MOE M-LOK hand guards' own gray, because this hand guard's own photos agree with it: make color-match (2026-10-28, JOB=moesl), the mid-length's upper side flat above its first slot in the hero direction, light backdrop, build bcm-16-mid with the drop-in parts, under polymer (satin), where that preset renders #5a595e. Two sets of photos with the other three colours beside the gray, each taken into the app's light by a gain and offset in linear light fitted on its black, Flat Dark Earth and OD green against the app's renders of magpul-black, magpul-fde and magpul-odg on that flat (#323232, #7e6c55, #484137): Midwest Gun Works' photo of the four mid-lengths stacked (references/magpul-moe-sl-handguard-mid 1dfa5c3d58f1, the band above each one's second slot: #363636, #a4907f, #595041, gray #6c6b73) gives #535258; Magpul's gallery pose 01 of the carbine (references/magpul-moe-sl-handguard-carbine 8a8452bc4ff3, 6f0160b92fb9, 7b86c2cc8f83, adace9984567, the same band: #595353, #978674, #6e6252, gray #827c83) gives #676068, warmer (its black maps to #372e2e). Their mean, #5d5960, is within 3 levels of what the preset renders, inside the two sets' own 20 levels apart. On the same flat the K2+'s and the MOE SL stock's Stealth Gray (magpul-stealth-gray, #4e4f53) renders #505153: the hand guard is drawn 10 levels lighter, as both of Magpul's hand guards' photos have it."},"heat_shield":{"label":"Heat shield","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"\"The integral, riveted aluminum heat shield\" (Magpul): a bare bright sheet inside the lower half (Magpul's feature 04, d70407049a05, shows it out of the black one), with its rivets' heads on the underside, the same in every colourway. Drawn in the bright metal finish on file; its alloy and temper aren't stated."}},"components":{},"geometry":{"model":"magpul-moe-sl-handguard-carbine.glb","components":{},"approximations":["Seated at its cap (the cap's `seats`, ar15.handguard_front): its front flange's end at the inside of the cap's face, and its rear end as far into the delta ring as its mounting length then takes it (a tenth of an inch or so on BCM's barrels). The ring is drawn at its forward stop, as the Army's drawing has it with no hand guard in; on the rifle it gives way that much on its spring (std.ar15.slip_ring_front_x), so what this part and the ring share as drawn is hidden inside the ring.","One model of both halves (the seam a groove along each side, seam_y): the two are never apart on a rifle, they come in one box and one colour, and Magpul sells them as one product.","Its section about the bore is an assumption past what the photos give (Magpul's width 1.8 in; its top and bottom from the bore and the slots' height from the FDE rifle's level photo): a flat underside rounding up into upright sides at the lower-edge slots (lower_round_y, bottom_half_width), upright sides to the M-LOK faces, which lean in at the angle the photos from above and from the side allow (mlok_side_face_angle), a flat for the slots (face_flat), and a near-flat top (top_half_width) holding the two rows of top slots. No view on file looks at an end square on.","Its height is the photo's (2.32 in, its own M-LOK slots at the standard's pitch); Magpul gives 2.4. Its width is Magpul's 1.8 in, which the view from above reads at 1.73 (its sides further from the lens than its top).","Its rear: the tongues the outline shows reaching back over the delta ring are the body's section, cut by the ring's cylinder (std.ar15.slip_ring_od and a clearance, ring_clearance, assumed), which opens the window in each side where the ring shows (the ring is wider than the hand guard); the rear flanges in the ring's skirt are a round collar (rear_collar_od, assumed), hollow.","Inside: the section less a wall of 0.15 in (wall, assumed, set by Magpul's weight at the polymer's density on file with the aluminium shield), from a rear wall round the barrel nut to a front wall; ahead of the front wall the shell is its side extensions and its front lip, open over the top where the front sight base's tower stands. The front flange that goes into the cap is a round lip on the front wall (front_flange_od, front_flange_length: assumed), as long as Magpul's mounting length says. The gas tube's way through each end is a notch as wide as the delta ring's own.","Three M-LOK slots in each upper side face and four in the underside, at the standard's size and pitch, where the photos have them. The eight small slots in each row along the top, the ten along each lower edge and the eight grooves along the crown where Magpul's photos from above and below have them; the slots blind (notch_depth), their widths and the grooves' depth assumed. The ribs down the lower half stand from the panels between them (rib_width, rib_height: assumed).","The heat shield is a liner of 0.03 in (assumed) inside the lower half, slotted with the underside's row; its two rivets' heads on the underside where the photo from below has them (their height assumed).","Its nose (the front panel ahead of its hood) is drawn as the lines its traced runs fit, not as traced: where the panel meets the front sight base's legs, its lug and its MOE SL letters the mask's edge wanders a few pixels either side of the part's. The hood's front face and the front edge are each the line through its run (the front edge leans back a little toward the top, as Magpul's black photo and Primary Arms' Flat Dark Earth one show it), the side extensions' top the level through its run, the top front corner a round of the size the black photo shows (nose_corner_x, nose_corner_y), the lip as traced (clean_nose in the script; what it fitted is in the manifest's `nose`).","Edges rounded at 0.02 in (moulded; their size isn't read). Not drawn: the MAGPUL, M and MOE SL marks."],"ledger":["magpul-moe-sl-handguard-carbine.length","magpul-moe-sl-handguard-carbine.width","magpul-moe-sl-handguard-carbine.height","magpul-moe-sl-handguard-carbine.mounting_length","magpul-moe-sl-handguard-carbine.rear_x"]},"profiles":{"side":{"plane":"xy","origin":"the rear end of its tongues over the delta ring, and its top","offset":{"x":"outline_rear_x","y":"top_above_axis"},"points":[[0,-0.483],[0,-0.542],[0.073,-0.556],[0.22,-0.41],[0.278,-0.41],[0.381,-0.512],[0.351,-0.542],[0.366,-0.586],[0.454,-0.586],[0.483,-0.556],[0.586,-0.659],[0.586,-0.893],[0.629,-0.878],[0.732,-0.981],[0.586,-1.156],[0.644,-1.215],[0.586,-1.274],[0.586,-1.361],[0.425,-1.552],[0.293,-1.42],[0.293,-1.303],[0.263,-1.303],[0.263,-1.742],[0.351,-1.83],[0.351,-1.918],[0.22,-2.049],[0.117,-1.947],[0.117,-1.771],[0.059,-1.713],[0.059,-1.537],[0,-1.508],[0,-1.683],[0.029,-1.742],[0,-1.8],[0.029,-1.859],[0,-1.888],[0,-1.976],[0.088,-2.064],[0.088,-2.21],[0.132,-2.313],[0.659,-2.313],[0.834,-2.371],[8.241,-2.371],[8.446,-2.547],[8.68,-2.547],[8.754,-2.503],[8.812,-2.093],[8.9,-2.005],[8.9,-1.654],[8.871,-1.596],[8.9,-1.566],[8.9,-1.332],[8.871,-1.303],[8.9,-1.274],[8.9,-1.186],[8.841,-1.098],[8.9,-1.01],[8.754,-0.893],[8.724,-0.395],[8.637,-0.307],[8.622,-0.234],[8.578,-0.278],[8.578,-0.366],[8.475,-0.468],[7.451,-0.468],[7.319,-0.337],[7.378,-0.22],[7.363,-0.176],[7.275,-0.263],[7.173,-0.161],[7.231,-0.102],[7.217,-0.088],[7.158,-0.117],[7.041,0],[6.953,0],[6.895,-0.059],[0.132,-0.059],[0.117,-0.337],[0.146,-0.366]],"scaleRefs":["magpul-moe-sl-handguard-carbine.length"],"inputs":{"magpul-moe-sl-handguard-carbine.length":8.9},"tolerance":0.02,"photo":"references/magpul-moe-sl-handguard-carbine 94b9fe2cb318 (Magpul's mag538-fde_04: the Flat Dark Earth hand guard on a rifle with an A2 front sight base, the rifle's right side seen level, 1200 x 1200)","method":"saturation > 0.15, inside [604, 495, 908, 625], closing ×3, largest piece, holes filled; scale from magpul-moe-sl-handguard-carbine.length = 8.9 in (x-extent 304 px → 34.2 px/in); origin at x min, y max of the outline; Douglas-Peucker at 0.02 in with the extremes kept: 79 points (IoU 0.999 with the full outline); The outline is the Flat Dark Earth's (saturation over 0.15): the black delta ring in its windows and the front sight base are left out. Its scale is Magpul's maximum length; the three M-LOK slots in the same photo, at the standard's 40 mm pitch, read it 1.8% longer (two pixels at each end).; checks: −y_min in x [1.0, 5.5] 2.371 ± 0.044; −y_min 2.547 ± 0.044 (tools/trace.py)","via":"harvest","note":"Its M-LOK slots, its small slots, its ribs and the seam are inside the outline; the model cuts them from the ledger. The window in each side of its rear, where the ring shows, is filled with the ring here: the model cuts it (the ring's cylinder). The front lower lip is the outline's lowest point at its front."}},"gaps":[{"what":"Its section square on (how the crown, the faces and the underside are shaped) and its wall","need":"An end view with a known size in frame, or a half alone from inside; Magpul publishes no drawing"},{"what":"Where its tongues and window sit against a delta ring placed by the standard: the photos have the ring's front end at the window's front edge, which places the hand guard here; the standard puts the ring itself 0.2 to 0.4 in further back than Magpul's rifle shows it against its receiver","need":"A photo of a MOE SL on a rifle whose receiver, delta ring and hand guard are all in frame from the side, close"},{"what":"Its front flange and what is inside the side extensions","need":"A photo into its front end, or of the upper half alone"},{"what":"Magpul's height, 2.4 in, against the photos' 2.32","need":"What Magpul measured over; a seller's or a reviewer's own measurement"}]},"magpul-moe-sl-handguard-mid":{"id":"magpul-moe-sl-handguard-mid","name":"MOE SL® Hand Guard, Mid-Length – AR15/M4","manufacturer":"Magpul","sku":"MAG551","url":"https://magpul.com/moeslhandguard-mid-length-ar15-m4.html","category":"handguard","description":"Magpul's slim polymer drop-in hand guard for a mid-length gas system and an A2 front sight, in two halves: \"An upgrade to AR15/M4 firearms with mid-length gas systems\"; \"Narrow cross section reduces weight and bulk\"; \"M-LOK® slots at two, six, and ten o'clock for accessories\"; \"Internal aluminum heat shield, front lip and side extensions protect against high heat during firing\"; \"Front lip and long side extensions shields hand from hot sight assembly\"; \"Made in the USA\" (Magpul). It goes on the rifle's own barrel nut and delta ring and the round cap behind its A2 front sight base: no free-float nut of its own.","weight":"magpul-moe-sl-handguard-mid.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[{"slot":"gas_block","parts":["bcm-front-sight-base-f-750"],"says":"Magpul, MOE SL Hand Guard, Mid-Length: \"Only compatible with firearms that include an A2 front sight assembly and a round front hand guard retaining cap.\"; \"*Must be used with the A2 front sight assembly as other gas blocks are not compatible. If so equipped, the factory sling swivel must be removed from the A2 front sight assembly.\"; \"Not compatible with piston operated AR platforms.\"","source":"https://magpul.com/moeslhandguard-mid-length-ar15-m4.html"}],"needs":{"slots":["barrel_nut","delta_ring","handguard_cap"],"says":"Magpul: \"Compatible with firearms with an A2 front sight assembly, a round front hand guard retaining cap, and rear spring-loaded delta ring\", \"requires a ROUND front hand guard retaining cap and rear spring-loaded delta ring\"; its instructions: \"Slide the front flange of the Upper Hand Guard piece into the metal hand guard cap, located behind the front sight base/gas block\" and \"make sure your delta ring is securing BOTH upper and lower rear flanges of the Hand Guards\".","source":"https://magpul.com/moeslhandguard-mid-length-ar15-m4.html"},"anchors":{"mount":{"origin":["0in - {.rear_x}",0,0],"note":"The receiver's front face on the bore axis, +x toward the muzzle: its rear flanges stand in the delta ring's skirt against the ring's lip (std.ar15.slip_ring_front_x ahead of the receiver)."},"mlok":{"origin":["{.mlok_side_slot0_x}","{.mlok_axis_y}",0],"note":"At the upper side faces' rearmost M-LOK slot's centre (index 0), +x toward the muzzle, on the axis the faces' normals through their slots' centres meet (mlok_axis_y, above the bore): the faces are angles about this axis."},"mlok_bottom":{"origin":["{.mlok_bottom_slot0_x}",0,0],"note":"The same axis at the underside's rearmost slot's centre (read from below, in line with the side rows')."},"cap_seat":{"origin":["{.mounting_length}",0,0],"note":"The front flange's front end, on the bore axis: what goes into the round hand guard cap (Magpul's mounting length ahead of its rear flanges' end)."}},"interfaces":{"cap_seat":{"type":"ar15.handguard_front","role":"handguard","anchor":"cap_seat","params":{},"flips":false},"handguard_mount":{"type":"ar15.handguard_mount","role":"handguard","anchor":"mount","params":{"nut":"standard"},"flips":false,"note":"On the rifle's own barrel nut and delta ring: Magpul, \"Easy to install utilizing existing delta ring and ROUND front hand guard retaining cap with A2 front sight assembly*\". Placed by the standard's delta ring (rear_x): its instructions, \"make sure your delta ring is securing BOTH upper and lower rear flanges of the Hand Guards\"."},"drop_in":{"type":"ar15.drop_in","role":"handguard","params":{"shape":"round"},"flips":false,"note":"Magpul (its page, read on the harvested copy): \"Only compatible with firearms that include an A2 front sight assembly and a round front hand guard retaining cap.\"; \"The Mid-Length MOE SL Hand Guard is a direct replacement for most factory plastic, two-piece, mid-length hand guards and requires a ROUND front hand guard retaining cap and rear spring-loaded delta ring (some mid-length firearms are equipped with a triangular retaining cap and are not compatible).\" Primary Arms: \"Triangular retaining caps and non-A2 gas blocks are not compatible.\""},"gas_system":{"type":"ar15.gas_system","role":"handguard","params":{"length":"mid"},"flips":false,"note":"Magpul names it \"Mid-Length\": \"Compatibility AR15/M4 firearms with mid-length gas system and A2 front sight*\", \"An upgrade to AR15/M4 firearms with mid-length gas systems\"; Primary Arms: \"Gas System Length Mid-Length\". (Its Features list opens \"Replaces carbine-length GI hand guard\", the carbine's sentence left on the mid-length's page.)"},"mlok":{"type":"mlok","role":"slots","anchor":"mlok","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_side_slots}","interval":"={std.mlok.interval}","face_distance":"={.mlok_side_face_distance}","reach_inside":"={.reach_inside}"},"faces":{"right_upper":{"angle":"{.mlok_side_face_angle}","note":"Magpul's two o'clock (the rifle's right, +z)"},"left_upper":{"angle":"0 - {.mlok_side_face_angle}","note":"Magpul's ten o'clock"}},"flips":false,"note":"Magpul: \"M-LOK® slots at two, six, and ten o'clock for accessories\". Four in each, counted on Magpul's and Primary Arms' photos and its instruction sheet's drawing."},"mlok_bottom":{"type":"mlok","role":"slots","anchor":"mlok_bottom","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_bottom_slots}","interval":"={std.mlok.interval}","face_distance":"={.mlok_bottom_face_distance}","reach_inside":"={.reach_inside}"},"faces":{"bottom":{"angle":180,"note":"the underside (Magpul's six o'clock)"}},"flips":false,"note":"Magpul's six o'clock row, with a vertical grip on it in Magpul's photo (c706e2992834). No view on file looks at the mid-length's underside: its count and places are the side rows' (mlok_bottom_slots, assumed), and kept as a gap."}},"materials":{"body":{"label":"Hand guard","finish":"polymer","recolorable":true,"color":"magpul-black","sheen":"satin","options":{"black":{"label":"Black","finish":"polymer","color":"magpul-black","sheen":"satin","sku":"MAG551-BLK","source":"https://magpul.com/moeslhandguard-mid-length-ar15-m4.html"},"fde":{"label":"Flat Dark Earth","finish":"polymer","color":"magpul-fde","sheen":"satin","sku":"MAG551-FDE","source":"https://magpul.com/moeslhandguard-mid-length-ar15-m4.html"},"odg":{"label":"Olive Drab Green","finish":"polymer","color":"magpul-odg","sheen":"satin","sku":"MAG551-ODG","source":"https://magpul.com/moeslhandguard-mid-length-ar15-m4.html"},"gry":{"label":"Stealth Gray","finish":"polymer","color":"magpul-stealth-gray-moe-mlok","sheen":"satin","sku":"MAG551-GRY","source":"https://magpul.com/moeslhandguard-mid-length-ar15-m4.html"}},"default":"black","note":"Both halves are one colour in each colourway (Magpul's gallery shots of its black and OD green, and Midwest Gun Works' photo of the four side by side, 1dfa5c3d58f1): \"reinforced, heat-resistant Magpul polymer\"; Magpul's page names the four (its colour swatches for MAG551: Black, Flat Dark Earth, Olive Drab Green, Stealth Gray); the numbers are Midwest Gun Works' (\"MAG551-BLK Black MAG551-FDE Flat Dark Earth MAG551-GRY Gray MAG551-ODG OD Green\") ; Primary Arms' Flat Dark Earth page: \"Color Flat Dark Earth Finish Matte\". The gray is drawn in `magpul-stealth-gray-moe-mlok`, the MOE M-LOK hand guards' own gray, because this hand guard's own photos agree with it: make color-match (2026-10-28, JOB=moesl), the mid-length's upper side flat above its first slot in the hero direction, light backdrop, build bcm-16-mid with the drop-in parts, under polymer (satin), where that preset renders #5a595e. Two sets of photos with the other three colours beside the gray, each taken into the app's light by a gain and offset in linear light fitted on its black, Flat Dark Earth and OD green against the app's renders of magpul-black, magpul-fde and magpul-odg on that flat (#323232, #7e6c55, #484137): Midwest Gun Works' photo of the four mid-lengths stacked (references/magpul-moe-sl-handguard-mid 1dfa5c3d58f1, the band above each one's second slot: #363636, #a4907f, #595041, gray #6c6b73) gives #535258; Magpul's gallery pose 01 of the carbine (references/magpul-moe-sl-handguard-carbine 8a8452bc4ff3, 6f0160b92fb9, 7b86c2cc8f83, adace9984567, the same band: #595353, #978674, #6e6252, gray #827c83) gives #676068, warmer (its black maps to #372e2e). Their mean, #5d5960, is within 3 levels of what the preset renders, inside the two sets' own 20 levels apart. On the same flat the K2+'s and the MOE SL stock's Stealth Gray (magpul-stealth-gray, #4e4f53) renders #505153: the hand guard is drawn 10 levels lighter, as both of Magpul's hand guards' photos have it."},"heat_shield":{"label":"Heat shield","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"\"The integral, riveted aluminum heat shield\" (Magpul): a bare bright sheet inside the lower half (Magpul's feature 04, 70b6f543f381, shows the lower half with it), the same in every colourway. Drawn in the bright metal finish on file; its alloy and temper aren't stated."}},"components":{},"geometry":{"model":"magpul-moe-sl-handguard-mid.glb","components":{},"approximations":["Seated at its cap (the cap's `seats`, ar15.handguard_front): its front flange's end at the inside of the cap's face, and its rear end as far into the delta ring as its mounting length then takes it (a tenth of an inch or so on BCM's barrels). The ring is drawn at its forward stop, as the Army's drawing has it with no hand guard in; on the rifle it gives way that much on its spring (std.ar15.slip_ring_front_x), so what this part and the ring share as drawn is hidden inside the ring.","One model of both halves (the seam a groove along each side, seam_y): the two are never apart on a rifle, they come in one box and one colour, and Magpul sells them as one product.","Its section about the bore is an assumption past what the photos give (Magpul's width 1.8 in; its top and bottom from the bore and the slots' height from the OD green rifle's level photo): a flat underside rounding up into upright sides at the lower-edge slots (lower_round_y, bottom_half_width), upright sides to the M-LOK faces, which lean in at the angle the photos from above and from the side allow (mlok_side_face_angle), a flat for the slots (face_flat), and a near-flat top (top_half_width) holding the two rows of top slots. No view on file looks at an end square on.","Its height is the photo's (2.32 in, its own M-LOK slots at the standard's pitch); Magpul gives 2.4. Its width is Magpul's 1.8 in, which the view from above reads at 1.75 (its sides further from the lens than its top).","Its rear: the tongues the outline shows reaching back over the delta ring are the body's section, cut by the ring's cylinder (std.ar15.slip_ring_od and a clearance, ring_clearance, assumed), which opens the window in each side where the ring shows (the ring is wider than the hand guard); the rear flanges in the ring's skirt are a round collar (rear_collar_od, assumed), hollow.","Inside: the section less a wall of 0.15 in (wall, assumed, set by Magpul's weight at the polymer's density on file with the aluminium shield), from a rear wall round the barrel nut to a front wall; ahead of the front wall the shell is its side extensions and its front lip, open over the top where the front sight base's tower stands. The front flange that goes into the cap is a round lip on the front wall (front_flange_od, front_flange_length: assumed), as long as Magpul's mounting length says. The gas tube's way through each end is a notch as wide as the delta ring's own.","Four M-LOK slots in each upper side face at the standard's size and pitch, where the level photo has them; the underside's row of four in line with them (assumed: no view on file looks at the underside). The ten small slots in each row along the top and the eight grooves along the crown where Magpul's photo from above has them, the thirteen along each lower edge where the level photo has them; the slots blind (notch_depth), their widths and the grooves' depth assumed. The ribs down the lower half stand from the panels between them (rib_width, rib_height: assumed).","The heat shield is a liner of 0.03 in (assumed) inside the lower half, slotted with the underside's row; its rivets aren't drawn (no view on file shows the mid-length's underside).","Its nose (the front panel ahead of its hood) is drawn as the lines its traced runs fit, not as traced: where the panel meets the front sight base's legs, its lug and its MOE SL letters the mask's edge wanders a few pixels either side of the part's. The hood's front face and the front edge are each the line through its run (the front edge leans back a little toward the top, as Magpul's black photo and Primary Arms' Flat Dark Earth one show it), the side extensions' top the level through its run, the top front corner a round of the size the black photo shows (nose_corner_x, nose_corner_y), the lip as traced (clean_nose in the script; what it fitted is in the manifest's `nose`).","Edges rounded at 0.02 in (moulded; their size isn't read). Not drawn: the MAGPUL, M and MOE SL marks."],"ledger":["magpul-moe-sl-handguard-mid.length","magpul-moe-sl-handguard-mid.width","magpul-moe-sl-handguard-mid.height","magpul-moe-sl-handguard-mid.mounting_length","magpul-moe-sl-handguard-mid.rear_x"]},"profiles":{"side":{"plane":"xy","origin":"the rear end of its upper tongue over the delta ring, and its top","offset":{"x":"outline_rear_x","y":"top_above_axis"},"points":[[0,-0.203],[0,-0.329],[0.028,-0.357],[0.014,-0.399],[0.028,-0.413],[0.091,-0.42],[0.175,-0.504],[0.259,-0.532],[0.287,-0.518],[0.301,-0.532],[0.539,-0.532],[0.616,-0.609],[0.616,-0.792],[0.658,-0.834],[0.616,-0.876],[0.616,-0.96],[0.637,-0.953],[0.729,-1.044],[0.729,-1.086],[0.701,-1.128],[0.715,-1.198],[0.701,-1.268],[0.715,-1.282],[0.644,-1.352],[0.729,-1.436],[0.729,-1.52],[0.701,-1.548],[0.687,-1.716],[0.616,-1.786],[0.616,-1.912],[0.651,-1.905],[0.687,-1.94],[0.729,-1.982],[0.729,-2.024],[0.651,-2.102],[0.616,-2.109],[0.616,-2.319],[0.672,-2.375],[0.658,-2.431],[0.708,-2.438],[0.736,-2.466],[1.45,-2.466],[1.506,-2.452],[1.52,-2.466],[1.618,-2.466],[1.632,-2.452],[2.277,-2.452],[2.291,-2.438],[2.305,-2.452],[3.748,-2.438],[3.762,-2.452],[3.93,-2.452],[3.944,-2.438],[4.098,-2.438],[4.196,-2.452],[4.21,-2.438],[4.42,-2.438],[4.448,-2.452],[4.462,-2.438],[5.051,-2.438],[5.079,-2.466],[6.298,-2.466],[6.326,-2.452],[6.34,-2.466],[6.592,-2.466],[6.62,-2.438],[6.9,-2.438],[6.914,-2.424],[6.942,-2.438],[7.783,-2.424],[7.797,-2.438],[8.763,-2.438],[8.777,-2.424],[9.338,-2.424],[9.352,-2.41],[9.478,-2.438],[9.618,-2.424],[9.632,-2.438],[10.024,-2.438],[10.066,-2.424],[10.108,-2.438],[10.136,-2.424],[10.15,-2.438],[10.291,-2.438],[10.445,-2.48],[10.599,-2.648],[10.697,-2.648],[10.725,-2.62],[10.781,-2.634],[10.809,-2.62],[10.844,-2.571],[10.858,-2.319],[10.872,-2.305],[10.858,-2.109],[10.9,-2.067],[10.858,-2.024],[10.83,-1.912],[10.844,-1.884],[10.816,-1.856],[10.83,-1.772],[10.816,-1.702],[10.83,-1.688],[10.816,-1.646],[10.858,-1.604],[10.816,-1.562],[10.788,-1.45],[10.816,-1.422],[10.816,-1.1],[10.802,-1.072],[10.816,-0.974],[10.788,-0.946],[10.816,-0.862],[10.816,-0.764],[10.767,-0.771],[10.676,-0.679],[10.704,-0.651],[10.704,-0.567],[10.585,-0.462],[10.571,-0.476],[10.192,-0.476],[10.178,-0.49],[9.478,-0.49],[9.38,-0.392],[9.352,-0.42],[9.338,-0.406],[9.268,-0.448],[9.177,-0.357],[9.191,-0.287],[9.135,-0.231],[9.149,-0.203],[9.079,-0.133],[9.051,-0.049],[9.002,0],[8.918,0],[8.791,-0.084],[8.469,-0.07],[8.455,-0.084],[7.362,-0.084],[7.348,-0.098],[7.334,-0.084],[6.326,-0.098],[6.228,-0.084],[6.214,-0.098],[4.252,-0.098],[4.21,-0.112],[4.196,-0.098],[4.14,-0.112],[4.098,-0.098],[4.056,-0.14],[4.028,-0.112],[2.305,-0.112],[2.263,-0.154],[2.235,-0.126],[2.193,-0.14],[2.081,-0.14],[2.067,-0.126],[0.736,-0.126],[0.637,-0.14],[0.623,-0.126],[0.525,-0.14],[0.511,-0.126],[0.091,-0.126],[0.021,-0.168]],"scaleRefs":["magpul-moe-sl-handguard-mid.length"],"inputs":{"magpul-moe-sl-handguard-mid.length":10.9},"tolerance":0.012,"photo":"references/magpul-moe-sl-handguard-mid fa1c10e48cd7 (Magpul's mag551-odg_03: the OD green hand guard on a rifle with an A2 front sight base, the rifle's right side seen level, 1200 x 1200)","method":"saturation > 0.12, inside [190, 345, 1000, 565], 1 boxes excluded, closing ×5, largest piece, holes filled; scale from magpul-moe-sl-handguard-mid.length = 10.9 in (x-extent 778 px → 71.4 px/in); origin at x min, y max of the outline; Douglas-Peucker at 0.012 in with the extremes kept: 163 points (IoU 0.998 with the full outline); The outline is the OD green's (saturation over 0.12): the black delta ring in its windows and the front sight base are left out, and the OD green vertical grip under it is cut off at the body's bottom edge (a box from row 530). Its scale is Magpul's maximum length; the four M-LOK slots in the same photo, at the standard's 40 mm pitch, give it within 0.4%. The lower tongue at its rear is the black's grey in this recoloured photo and isn't in the outline: the model builds both tongues from the body's section.; checks: −y_min in x [1.0, 7.5] 2.466 ± 0.024; −y_min 2.648 ± 0.024 (tools/trace.py)","via":"harvest","note":"Its M-LOK slots, its small slots, its ribs and the seam are inside the outline; the model cuts them from the ledger. The front lower lip is the outline's lowest point at its front."}},"gaps":[{"what":"Its underside: the six o'clock M-LOK row's count and places, and the heat shield's rivets","need":"A photo of a MOE SL mid-length from below, its whole underside in frame (Magpul's carbine has one, d4a119f9380f)"},{"what":"Its section square on (how the crown, the faces and the underside are shaped) and its wall","need":"An end view with a known size in frame, or a half alone from inside; Magpul publishes no drawing"},{"what":"Where its tongues and window sit against a delta ring placed by the standard: the photos have the ring's front end at the window's front edge, which places the hand guard here; the standard puts the ring itself 0.3 to 0.4 in further back than Magpul's rifle shows it against its receiver","need":"A photo of a MOE SL on a rifle whose receiver, delta ring and hand guard are all in frame from the side, close"},{"what":"Its front flange and what is inside the side extensions","need":"A photo into its front end, or of the upper half alone"},{"what":"Magpul's height, 2.4 in, against the photos' 2.32","need":"What Magpul measured over; a seller's or a reviewer's own measurement"}]},"magpul-moe-trigger-guard":{"id":"magpul-moe-trigger-guard","name":"MOE enhanced trigger guard, polymer","manufacturer":"Magpul","sku":"MAG1186","category":"trigger_guard","weight":"magpul-moe-trigger-guard.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"trigger_guard":{"origin":[0,0,0]}},"interfaces":{"trigger_guard":{"type":"ar15.trigger_guard","role":"guard","anchor":"trigger_guard","params":{},"flips":false}},"materials":{"body":{"label":"Trigger guard","finish":"polymer","recolorable":true,"color":"magpul-black","sheen":"matte","options":{"black":{"label":"Black","finish":"polymer","color":"magpul-black","sheen":"matte","sku":"MAG1186-BLK","source":"https://magpul.com/moe-enhanced-trigger-guard-polymer-ar15-m4.html"},"fde":{"label":"FDE","finish":"polymer","color":"magpul-fde","sheen":"matte","sku":"MAG1186-FDE","source":"https://magpul.com/moe-enhanced-trigger-guard-polymer-ar15-m4.html"},"odg":{"label":"ODG","finish":"polymer","color":"magpul-odg","sheen":"matte","sku":"MAG1186-ODG","source":"https://magpul.com/moe-enhanced-trigger-guard-polymer-ar15-m4.html"},"sgy":{"label":"Stealth Gray","finish":"polymer","color":"magpul-stealth-gray","sheen":"matte","sku":"MAG1186-GRY","source":"https://magpul.com/moe-enhanced-trigger-guard-polymer-ar15-m4.html"}},"default":"black","note":"The four colours Magpul's page offers MAG1186 in (its swatches: Black, Flat Dark Earth, Olive Drab Green, Stealth Gray, each with its number), as matched on the MOE SL. The guard is one moulding and one colour all over in each (Magpul's gallery shots 01 to 03 of each; a distributor's large photos of the black, FDE and OD ones: references/magpul-moe-trigger-guard f91328a45866, 1cca2775d685, 48304dbcf96e). Its set screws are black steel on every colour (the same photos, the screws lying beside the guard; Magpul: 'three set screws for mounting') and aren't drawn: they go into the holes in its ends."}},"components":{"body":{"label":"Trigger guard","material":"body"}},"geometry":{"model":"magpul-moe-trigger-guard.glb","components":{},"approximations":["Visual hull of the traced side view and Magpul's underside plan view (scaled by the side's length; it reads 0.631 across the belly against the listed 0.62): the belly and the narrower end tabs that sit between the receiver's ears.","The plan's outline holds at every height the side shows, so the belly's full width begins 0.2 in inside the receiver's rear ears, where the real one is still its tab's width (0.004 cubic inches of it in the Workhorse's rear ears, 2026-10-05); the ear holes and the logo aren't drawn; edges broken at 0.02 in."],"ledger":["magpul-moe-trigger-guard.ear_spacing","magpul-moe-trigger-guard.length_side","magpul-moe-trigger-guard.front_ahead_of_hole","magpul-moe-trigger-guard.width_listed"]},"profiles":{"side":{"plane":"xy","origin":"the front ear hole's centre (the guard frame origin); the rear ear hole on the x axis behind it","offset":{},"points":[[-2.154,-0.105],[-2.117,-0.142],[-1.3,-0.337],[-1.019,-0.363],[0.122,-0.175],[0.141,-0.147],[0.143,0.042],[0.141,0.09],[0.122,0.109],[-0.1,0.111],[-0.272,-0.036],[-0.437,-0.115],[-0.93,-0.204],[-1.098,-0.21],[-1.236,-0.185],[-1.35,-0.142],[-1.75,0.122],[-2.115,0.124],[-2.15,0.104]],"scaleRefs":["magpul-moe-trigger-guard.ear_spacing"],"inputs":{"magpul-moe-trigger-guard.ear_spacing":1.844},"tolerance":0.01,"photo":"references/magpul-moe-trigger-guard ef1ccb74431e (true side view (Stealth Gray, Wing Tactical), 1280 px)","method":"luminance < 200, closing ×1, largest piece, holes filled; frame from the reviewed holes front_ear (1140.5,579.5) r=29px, rear_ear (221.5,586.5) r=29px (498.4 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.01 in with the extremes kept: 19 points (IoU 0.973 with the full outline) (tools/trace.py)","via":"harvest","note":"Outer silhouette with the ear holes filled. Installed, the ears sit inside the lower's ears and the belly shows below them."},"plan":{"plane":"xz","origin":"the front tab's tip, centred across; offset to its place ahead of the front ear hole","offset":{"x":"front_ahead_of_hole"},"points":[[-2.297,0.007],[-2.289,-0.198],[-2.276,-0.212],[-1.984,-0.214],[-1.919,-0.27],[-1.779,-0.308],[-0.72,-0.315],[-0.301,-0.312],[-0.276,-0.289],[-0.269,-0.236],[-0.25,-0.22],[-0.016,-0.218],[0,-0.008],[-0.012,0.023],[-0.01,0.212],[-0.264,0.223],[-0.273,0.286],[-0.3,0.311],[-1.689,0.315],[-1.86,0.298],[-1.952,0.258],[-1.977,0.226],[-2.283,0.224]],"scaleRefs":["magpul-moe-trigger-guard.length_side"],"inputs":{"magpul-moe-trigger-guard.length_side":2.297},"tolerance":0.01,"photo":"references/magpul-moe-trigger-guard 025941c5c136 (Magpul gallery: MOE Enhanced Trigger Guard, underside plan view, 2000 px)","method":"luminance < 120, closing ×2, largest piece, holes filled; rotated -90.0° as declared; scale from magpul-moe-trigger-guard.length_side = 2.297 in (x-extent 1933 px → 841.5 px/in); origin at x max, y center of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 23 points (IoU 0.990 with the full outline); checks: height 0.631 ± 0.009 in vs magpul-moe-trigger-guard.width_listed 0.62 ± 0 (provisional): DISAGREES (tools/trace.py)","via":"harvest","note":"Seen from below; the outline is symmetric across, so its handedness doesn't matter. The second coordinate is z."}},"gaps":[]},"magpul-pmag-20-gen-m3":{"id":"magpul-pmag-20-gen-m3","name":"PMAG 20 AR/M4 GEN M3","manufacturer":"Magpul","sku":"MAG560","url":"https://magpul.com/pmag-20-ar-m4-gen-m3.html","category":"magazine","description":"Magpul's 20-round polymer magazine for AR-15/M4 rifles in 5.56 NATO and .223 Remington, the third generation: the 30-round's top on a body an inch and nine tenths shorter, which Magpul's sheet says 'accomodates firing from a prone position'. Its sheet says a pop-off impact and dust cover is included; it comes off before the magazine goes into a rifle and is not drawn.","weight":"magpul-pmag-20-gen-m3.weight","cartridge":{"takes":["5.56 NATO",".223 Rem"],"stated":"a 20-round polymer magazine for AR15/M4 compatible weapons chambered in 5.56x45 NATO / .223 Remington","source":"https://magpul.com/media/wysiwyg/GIS/MAG560_PMAG_20_AR_M4_GEN_M3_GIS_01.pdf (Magpul's information sheet for MAG560, as harvested 2026-10-13: its text layer)"},"rounds":{"capacity":"magpul-pmag-20-gen-m3.capacity","each":"magpul-pmag-20-gen-m3.round_weight"},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"magwell":{"origin":[0,"-{.catch_notch_top}",0],"note":"The upper edge of its catch notch, at its spine's rear face where it stands in the well: what hangs on the lower's catch, in the well's spine slot. Magazine frame: origin at the spine's rear face where the top section stands in a well, at the top of the feed lips; the traced side profile uses the same origin (the tip of the over-travel stop on the spine, under the well, is 0.06 in behind it: stop_behind_spine). The notch's height is this part's own, read on Magpul's photograph of it: 1.055 in under the lips, where the 30-round GEN M3's is 1.07."}},"interfaces":{"magwell":{"type":"ar15.magwell","role":"magazine","anchor":"magwell","params":{"family":"5.56"},"flips":false,"note":"Magpul's page: 'Compatibility: Wide compatibility with most 'STANAG 4179' platforms such as the AR15, M4, M16 ...'; its sheet: 'an over-travel stop on the spine helps ensure the magazine will not over-insert on compatible weapons'. A seller's own note (Primary Arms): 'GEN M3 PMAGs may not be compatible with all billet lowers without slight modification of the magazine overtravel stop.'"}},"materials":{"body":{"label":"Magazine body","finish":"polymer","recolorable":false,"color":"magpul-black","sheen":"matte","options":{"black":{"label":"Black","finish":"polymer","color":"magpul-black","sheen":"matte","sku":"MAG560-BLK","source":"https://magpul.com/pmag-20-ar-m4-gen-m3.html"},"odg":{"label":"ODG","finish":"polymer","color":"magpul-odg","sheen":"matte","sku":"MAG560-ODG","source":"https://shinertactical.com/product/magpul-pmag-20-m3-ar-m4-5-56-20rd-odg/"}},"default":"black","note":"The two colours Magpul's page offers MAG560 in (its swatches: Black, Olive Drab Green; its banner 'NOW IN ODG!'). MAG560-BLK is on Magpul's own page beside the black one's NSN (1005-01-710-3291); the page gives the green one no number in words (its script calls the two MAG560_RET_BLK_ and MAG560_RET_ODG_), and MAG560-ODG is a seller's statement of the 'Manufacturer Part Number' (Shiner Tactical, with UPC 873750007946): one seller, provisional. Both are Magpul's presets matched on its other parts (data/finishes.yaml), under 'Crush-resistant polymer body' (Magpul's page). In both colours the body and the floorplate are one colour (Magpul's gallery shots 01.1 and 02.1 of each: the green ones are the black ones' pictures recoloured, as Magpul's galleries are). The follower is light grey in the black one (shot 03.1) and isn't drawn: the model is a solid hull, closed at the feed lips; the green one's wasn't looked at (its shot 03.1 is in the page's gallery list and wasn't harvested). The lock plate's tab at the floorplate's rear is the body's colour (Magpul's feature picture 02) and isn't drawn. A Sand one (MAG560-SND) is on one seller's page not on file and nowhere on Magpul's: not offered."}},"components":{},"geometry":{"model":"magpul-pmag-20-gen-m3.glb","components":{},"approximations":["A visual hull of its own design patent's side and front elevations (US D691,233 S, FIG. 2 and FIG. 6: the one design patent Magpul's marking page lists against the PMAG 20 AR/M4 GEN M3, and it draws this magazine), scaled by Magpul's 5.6 in 'Length, max' taken as the height standing with the top section upright. What says the 5.6 in is that: scaled so, the patent's top section is 2.50 in front to back, Magpul's photograph of the product scaled the same way 2.49, and the 30-round GEN M3's 2.53 by its own figures. Magpul's photograph of the left side lies on the patent's left elevation (IoU 0.987), lower half and all: the body is not straight outside, its gripping half leans forward under an upright top as the 30-round's curve begins. A leaning magazine's section is taken as the front elevation at every height along it.","Its sides: the grip frame's ribs and bands stand where the front elevation's silhouette is, and the panels are cut down to the plane of the plain sides above the frame, as the patent's front and rear elevations show their floors in profile (0.028 in under the frame's face on the left and 0.030 on the right as built; the drawing's lines read 0.023 and 0.027). Where the panels are is the patent's left elevation: one row of three in the frame (the front one open to the front face, the rear one to the spine), and under the band the panel with the dot matrix and a second front one beside it, down to the floorplate. The right side's panels are the left's mirrored (the right elevation draws the same panels within 0.05 in). Each wall runs 0.027 in from its rim to its floor; the closed panel and the one with the dots, in no view's profile, are taken to the same floor as the others.","The floorplate begins at its own upper edge, the lower of the two parallel lines the left elevation draws under the dot matrix's panel, 11 degrees off level: the hull's flare (the front elevation's, which begins at one height all along) is taken back to the frame's face over that edge, and the body's rim between the panel and the edge is at the frame's face. Under the edge (2026-10-19) the floorplate's side is the front elevation's at its front end, carried along the edge: from where the flare begins there (the waist's last corner, at the edge's height at the front), 0.014 in in from the rim's face (the seam), out by the flare to its widest (0.549 in on the left 0.125 in under the edge, 0.552 on the right 0.39 under it: the outline's own corners each side). Until then it stood out of the rim with a square shoulder toward the spine, where the edge runs lower than the flare the hull carried at its front heights. Its own pockets, texture and lock plate aren't drawn. Magpul's photograph has the edge step down near the front, as the 30-round's does; this patent's edge is straight, and the step isn't drawn.","The over-travel stop (2026-10-19): the ledge behind the spine at the grip frame's top, read on this magazine's patent's two plans (FIG. 4 and 5) and its rear elevation (FIG. 7), the 30-round's ledge within 0.02 in. In plan its rear face is flat across the middle (0.287 in each side), its corners round (0.089 in, the round that meets both the flat and the side) and its sides lean out 18 degrees to 0.426 in each side where they meet the frame's top band, 0.224 in ahead of the rear face: narrower than the frame by 0.05 a side. From the rear its face comes down toward its ends to 0.128 in under the ledge's top (where the ledge meets the spine's face), and under its outer parts the underside is ruled from the face's lower edge at the rear to a straight edge at the spine's face, from 0.169 in under the top (read 0.385 in out) down to the spine's edge at the first row's top. Across the middle the face comes down to the rib's top, where the cut beside the rib begins (from the rear trace, 0.159 in under the ledge's top; read under the top on FIG. 7 it is 0.174, the readings 0.015 apart: the rib's is kept), and under it, either side of the gusset, it is hollow, out to a wall from 0.28 in at the rear face to the spine's edge at its face (FIG. 5). The underside's ruled faces are the simplest surfaces between the edges the drawings give; no view has it in section. The ledge's top is the hull's.","The dot matrix: sixty squares a side, four groups of three across and five down (counted on each elevation), each side's placed from its own elevation (the two come out each other's mirror within 0.006 in). Sunk (on Magpul's photo each square is dark along its upper edge, as the sunk panels are), 0.068 in across as the 30-round's are on Magpul's photo of that magazine (this one's patent draws them 0.086 to the middle of a heavy stroke, nearly touching; its photo has them apart). HOW DEEP IS ASSUMED: no view on file shows one in profile; six tenths of the panels' depth, as the 30-round's model has them. Straight walls.","On the left, the catch's window with its upper edge where the magazine hangs (1.055 in under the lips' top, on Magpul's photograph; the patent draws it 0.05 in lower, as the 30-round's patent does), drawn as a pocket as deep as a lower's catch slot is cut and not through (the model is solid; its corners are as round as the photo shows them, unsized). Under it the patent's front and rear elevations draw a block standing 0.057 in out of the side and Magpul's photo shows its outline: as on the 30-round it would stand in the left wall of a standard well under the catch's slot, so it is not drawn until that is reconciled (the ledger's catch_block entries). The hull is made without it.","The spine: from the top down to the over-travel stop, what the hull has behind the body's rear face and outside the spine's own width is cut away, so the spine alone (0.438 in wide by the rear elevation, standing 0.139 in behind the body by the side one, whose heavy line for the body's rear face runs the whole way up) runs in a well's slot. Over the step at its top (0.45 in under the lips) the spine's stepped top is the side outline's at that same width: the bolt catch's relief between the feed lips, which the rear elevation draws there, isn't. The stop is the side outline's, carried across the whole width, as the rear elevation has it.","The bars: five across the front strip in each of the frame's two rows and five across the spine in each of its two under the stop, each where the front and rear elevations draw it, as long as they draw it (0.415 in on the front, 0.40 on the spine) and 0.033 in thick. The side outline's teeth are taken out of the hull first (the strip under them is the straight line that touches the outline's edge from inside), so the bars are bars and not a ripple across the whole front and rear. The front ones stand 0.014 in out of the strip (the side elevation's small square across the edge's line); the spine's stand 0.022 in, the 30-round's figure by reference (this magazine's side views have no bar's own outline there). In the spine's upper row the long rib down the middle (0.148 in wide) is the outline's own edge, with the stop's gusset over it at the same width; beside it the strip is cut a bar's height further in and the row's five bars stand on it either side, a thousandth short of the rib's face. Plain bars with square ends: the elevations draw theirs bevelled.","The grip frame's four corners are turned, row by row and band by band, as the 30-round's are and by this magazine's own figures: at the front a quarter ellipse from the front strip's edge (the strip 0.437 in wide) round to where the side begins to turn in, 0.117 in behind the strip; at the rear the spine's strip standing 0.072 in behind a shoulder (0.545 in over the two) and a quarter ellipse from the shoulder's end round to the side over 0.124 in. A band's turn is its row's a panel's depth further out. ASSUMED quarter ellipses: no view has a turn in section, only the lines at its two ends. The frame's top band at the rear, under the stop, and the body's rim over the floorplate keep square corners.","The top section is 0.902 in wide as drawn (the two elevations agree), where a standard well is .898: 0.002 in a side inside a well's walls, a line's weight of the drawing. The one seller's table has 0.87 in; both are in the ledger.","Above the frame, where it stands in a well (detail pass, 2026-10-13, from this magazine's own patent): each side leans in from 0.60 in behind the front face to 0.70 in across, then rounds over 0.068 in into a front face 0.526 in wide; those four figures and the upper rib's 29 degrees are the 30-round GEN M3's keys by reference, which this patent's FIG. 2 and FIG. 6 bear out (0.591, 0.066, 0.695, 0.524 in; 29 and 30.5 degrees). Left at the side's own width: two guide ribs a side (the upper one's flat face 0.48 to 0.61 in under the lips, its upper face rising toward the middle at 29 degrees over a level lower face; the lower one's 2.00 to 2.10 in under the lips, a wedge both ways at 19 degrees, as FIG. 6 draws it), and the tab on the frame's upper edge (its top 2.31 in under the lips, 0.226 in long, its front side 0.2 in behind the front face, its sides leaning 3.6 degrees forward as they go down). The lean is one flat (the patent's line where it begins bows 0.02 in forward toward its ends, and the model's begins about 0.03 in further forward between the ribs, where the side is narrower than at the frame); the tab's face is the plain side's (FIG. 6 has it on the side's silhouette), its feet square on the edge, its upper corners round at the 30-round's 0.03 in (not read on this magazine). The body's rear corners beside the spine are round, 0.057 in (the 30-round's by reference; this patent's rear elevation reads 0.060 and its side one 0.050), from the top down to the frame.","The slim groove near the spine, on each side: where the patent's right side elevation draws it (its middle 0.415 in ahead of the spine's rear face, 0.048 in across, round ended, from 0.18 to 1.11 in under the lips' top); the left side's is the right's mirrored (Magpul's photo of the left side shows it there; not measured on it). HOW DEEP IS ASSUMED: it breaks no outline in any view on file; drawn 0.018 in, with walls leaning as far across as it is deep to a floor a quarter of its width.","Not drawn: the shallow relief above the catch's window and the two round marks under it, the cartridge mark and the lettering, the floorplate's pockets, texture and lock plate, the follower and the dust cover. Edges broken at 0.02 in. A solid hull says nothing of the weight: 12 cubic inches of plastic would be several times the 4 oz of a hollow body with its spring."],"ledger":["magpul-pmag-20-gen-m3.overall_height","magpul-pmag-20-gen-m3.front_to_back","magpul-pmag-20-gen-m3.width","magpul-pmag-20-gen-m3.hang_below_magwell","magpul-pmag-20-gen-m3.catch_notch_top","magpul-pmag-20-gen-m3.catch_notch_height","magpul-pmag-20-gen-m3.catch_notch_rear_x","magpul-pmag-20-gen-m3.catch_notch_front_x","magpul-pmag-20-gen-m3.side_panel_depth","magpul-pmag-20-gen-m3.side_panel_wall_run","magpul-pmag-20-gen-m3.side_panel_corner_radius","magpul-pmag-20-gen-m3.dot_depth","magpul-pmag-20-gen-m3.dot_size","magpul-pmag-20-gen-m3.dots_per_side","magpul-pmag-20-gen-m3.spine_width","magpul-pmag-20-gen-m3.spine_depth","magpul-pmag-20-gen-m3.bars_front","magpul-pmag-20-gen-m3.bars_spine","magpul-pmag-20-gen-m3.strip_bar_thickness","magpul-pmag-20-gen-m3.front_bar_proud","magpul-pmag-20-gen-m3.spine_bar_proud","magpul-pmag-20-gen-m3.spine_rib_width","magpul-pmag-20-gen-m3.front_strip_width","magpul-pmag-20-gen-m3.front_corner_depth","magpul-pmag-20-gen-m3.rear_shoulder_width","magpul-pmag-20-gen-m3.spine_strip_proud","magpul-pmag-20-gen-m3.rear_corner_depth","magpul-pmag-20-gen-m3.nose_taper_length","magpul-pmag-20-gen-m3.nose_round_depth","magpul-pmag-20-gen-m3.nose_shoulder_width","magpul-pmag-20-gen-m3.nose_front_width","magpul-pmag-20-gen-m3.guide_rib_top_angle","magpul-pmag-20-gen-m3.guide_rib_upper_top","magpul-pmag-20-gen-m3.guide_rib_upper_height","magpul-pmag-20-gen-m3.guide_rib_lower_top","magpul-pmag-20-gen-m3.guide_rib_lower_height","magpul-pmag-20-gen-m3.guide_rib_lower_angle","magpul-pmag-20-gen-m3.frame_tab_top","magpul-pmag-20-gen-m3.frame_tab_front","magpul-pmag-20-gen-m3.frame_tab_length","magpul-pmag-20-gen-m3.frame_tab_lean","magpul-pmag-20-gen-m3.frame_tab_corner_radius","magpul-pmag-20-gen-m3.upper_rear_corner_radius","magpul-pmag-20-gen-m3.spine_groove_x","magpul-pmag-20-gen-m3.spine_groove_width","magpul-pmag-20-gen-m3.spine_groove_top","magpul-pmag-20-gen-m3.spine_groove_length","magpul-pmag-20-gen-m3.stop_flat_half_width","magpul-pmag-20-gen-m3.stop_side_angle","magpul-pmag-20-gen-m3.stop_half_width","magpul-pmag-20-gen-m3.stop_length","magpul-pmag-20-gen-m3.stop_lip_depth_middle","magpul-pmag-20-gen-m3.stop_lip_level_half_width","magpul-pmag-20-gen-m3.stop_lip_depth_end","magpul-pmag-20-gen-m3.stop_lip_end_half_width","magpul-pmag-20-gen-m3.stop_wing_depth","magpul-pmag-20-gen-m3.stop_wing_half_width","magpul-pmag-20-gen-m3.stop_bay_half_width"]},"profiles":{"side":{"plane":"xy","origin":"the spine's rear face where the top section stands in the well, at the feed lips' top","offset":{},"points":[[-0.061,-3.124],[0.05,-3.381],[0.138,-4.199],[0.152,-4.287],[0.179,-4.315],[0.185,-4.428],[0.21,-4.522],[0.207,-4.58],[0.232,-4.676],[0.235,-4.759],[0.249,-4.781],[0.268,-4.889],[0.262,-4.925],[0.276,-4.944],[0.295,-5.049],[0.287,-5.074],[0.312,-5.132],[0.315,-5.201],[0.29,-5.295],[0.307,-5.408],[0.345,-5.549],[0.457,-5.6],[2.835,-5.131],[2.933,-5.03],[2.886,-4.787],[2.852,-4.729],[2.772,-4.27],[2.734,-4.016],[2.753,-3.986],[2.731,-3.831],[2.695,-3.793],[2.687,-3.735],[2.701,-3.718],[2.698,-3.691],[2.676,-3.644],[2.673,-3.605],[2.684,-3.594],[2.667,-3.577],[2.681,-3.564],[2.659,-3.511],[2.648,-3.423],[2.659,-3.392],[2.643,-3.359],[2.632,-3.268],[2.645,-3.254],[2.643,-3.224],[2.623,-3.193],[2.623,-3.169],[2.64,-3.152],[2.615,-3.122],[2.629,-3.094],[2.607,-3.025],[2.607,-3.003],[2.634,-2.97],[2.621,-2.801],[2.518,-2.705],[2.496,-2.647],[2.493,-0.211],[2.445,-0.174],[2.407,-0.185],[1.769,-0.138],[1.631,-0.091],[1.595,-0.099],[1.559,-0.091],[1.537,-0.102],[1.493,-0.091],[1.476,-0.102],[1.454,-0.091],[1.415,-0.105],[1.404,-0.094],[1.365,-0.094],[1.354,-0.105],[1.343,-0.094],[1.255,-0.08],[1.128,0],[0.189,0],[0.144,-0.026],[0.121,-0.261],[0.093,-0.29],[0.066,-0.297],[0.061,-0.418],[0.032,-0.447],[0,-0.457],[0.003,-2.97],[-0.058,-3.011]],"features":{"dots":[[[0.653,-4.519],[0.639,-4.434],[0.724,-4.42],[0.738,-4.505]],[[0.667,-4.617],[0.655,-4.532],[0.739,-4.52],[0.752,-4.605]],[[0.685,-4.719],[0.666,-4.633],[0.752,-4.614],[0.77,-4.7]],[[0.694,-4.812],[0.688,-4.726],[0.774,-4.719],[0.781,-4.805]],[[0.716,-4.913],[0.699,-4.828],[0.782,-4.812],[0.799,-4.896]],[[0.75,-4.505],[0.735,-4.42],[0.824,-4.405],[0.838,-4.49]],[[0.765,-4.602],[0.754,-4.516],[0.841,-4.505],[0.851,-4.592]],[[0.781,-4.703],[0.767,-4.615],[0.851,-4.601],[0.866,-4.688]],[[0.797,-4.798],[0.783,-4.714],[0.866,-4.7],[0.88,-4.785]],[[0.809,-4.894],[0.8,-4.809],[0.884,-4.8],[0.893,-4.884]],[[0.85,-4.493],[0.833,-4.405],[0.919,-4.388],[0.936,-4.475]],[[0.866,-4.59],[0.848,-4.503],[0.935,-4.486],[0.952,-4.572]],[[0.879,-4.685],[0.866,-4.601],[0.952,-4.588],[0.965,-4.672]],[[0.894,-4.783],[0.879,-4.699],[0.966,-4.685],[0.981,-4.769]],[[0.908,-4.882],[0.896,-4.796],[0.979,-4.784],[0.992,-4.87]],[[0.995,-4.467],[0.982,-4.378],[1.068,-4.366],[1.081,-4.455]],[[1.01,-4.566],[0.996,-4.481],[1.084,-4.466],[1.098,-4.551]],[[1.027,-4.663],[1.013,-4.579],[1.098,-4.565],[1.112,-4.649]],[[1.04,-4.759],[1.029,-4.677],[1.111,-4.665],[1.123,-4.748]],[[1.054,-4.86],[1.043,-4.772],[1.128,-4.762],[1.139,-4.85]],[[1.174,-4.446],[1.088,-4.446],[1.088,-4.357],[1.174,-4.357]],[[1.107,-4.55],[1.097,-4.465],[1.182,-4.455],[1.193,-4.539]],[[1.121,-4.646],[1.111,-4.561],[1.198,-4.552],[1.207,-4.636]],[[1.138,-4.745],[1.126,-4.661],[1.212,-4.648],[1.224,-4.733]],[[1.152,-4.844],[1.141,-4.755],[1.224,-4.745],[1.235,-4.834]],[[1.192,-4.439],[1.177,-4.354],[1.262,-4.339],[1.277,-4.425]],[[1.208,-4.535],[1.194,-4.45],[1.279,-4.436],[1.293,-4.521]],[[1.222,-4.633],[1.207,-4.549],[1.292,-4.534],[1.307,-4.618]],[[1.236,-4.733],[1.222,-4.647],[1.309,-4.633],[1.324,-4.718]],[[1.25,-4.833],[1.237,-4.743],[1.325,-4.73],[1.338,-4.821]],[[1.34,-4.416],[1.33,-4.329],[1.413,-4.319],[1.423,-4.405]],[[1.352,-4.511],[1.34,-4.428],[1.426,-4.416],[1.438,-4.499]],[[1.373,-4.618],[1.352,-4.531],[1.438,-4.509],[1.46,-4.597]],[[1.385,-4.709],[1.37,-4.623],[1.455,-4.609],[1.47,-4.695]],[[1.399,-4.808],[1.384,-4.724],[1.47,-4.709],[1.485,-4.793]],[[1.44,-4.401],[1.423,-4.317],[1.507,-4.3],[1.524,-4.384]],[[1.452,-4.497],[1.437,-4.413],[1.523,-4.398],[1.538,-4.483]],[[1.467,-4.596],[1.455,-4.51],[1.541,-4.497],[1.553,-4.584]],[[1.48,-4.693],[1.469,-4.607],[1.556,-4.597],[1.567,-4.682]],[[1.496,-4.792],[1.484,-4.707],[1.57,-4.695],[1.583,-4.78]],[[1.536,-4.384],[1.522,-4.301],[1.605,-4.287],[1.619,-4.37]],[[1.548,-4.483],[1.539,-4.395],[1.624,-4.386],[1.633,-4.474]],[[1.565,-4.582],[1.55,-4.494],[1.636,-4.48],[1.65,-4.568]],[[1.581,-4.679],[1.569,-4.594],[1.654,-4.582],[1.666,-4.667]],[[1.594,-4.775],[1.583,-4.689],[1.669,-4.678],[1.68,-4.764]],[[1.684,-4.362],[1.671,-4.276],[1.754,-4.265],[1.766,-4.351]],[[1.698,-4.461],[1.686,-4.375],[1.769,-4.363],[1.781,-4.449]],[[1.792,-4.553],[1.707,-4.553],[1.707,-4.468],[1.792,-4.468]],[[1.727,-4.659],[1.713,-4.574],[1.799,-4.559],[1.813,-4.645]],[[1.74,-4.754],[1.728,-4.669],[1.815,-4.657],[1.827,-4.742]],[[1.78,-4.348],[1.768,-4.262],[1.853,-4.249],[1.865,-4.336]],[[1.796,-4.446],[1.785,-4.357],[1.868,-4.347],[1.879,-4.436]],[[1.814,-4.546],[1.797,-4.463],[1.879,-4.445],[1.897,-4.528]],[[1.825,-4.641],[1.813,-4.556],[1.898,-4.544],[1.91,-4.629]],[[1.843,-4.742],[1.827,-4.655],[1.912,-4.64],[1.927,-4.727]],[[1.878,-4.334],[1.866,-4.246],[1.951,-4.233],[1.964,-4.322]],[[1.892,-4.43],[1.882,-4.346],[1.968,-4.336],[1.979,-4.42]],[[1.906,-4.526],[1.9,-4.442],[1.987,-4.435],[1.993,-4.519]],[[1.923,-4.624],[1.913,-4.541],[1.995,-4.531],[2.006,-4.614]],[[1.937,-4.726],[1.926,-4.638],[2.011,-4.628],[2.021,-4.715]]]},"scaleRefs":["magpul-pmag-20-gen-m3.overall_height"],"inputs":{"magpul-pmag-20-gen-m3.overall_height":5.6},"tolerance":0.008,"photo":"references/magpul-pmag-20-gen-m3 57d9f77b9610 (US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi)","method":"luminance < 128, inside [620, 640, 1820, 2820], 1 boxes excluded, closing ×8, holes filled, inset 2 px (half the outline's stroke); scale from magpul-pmag-20-gen-m3.overall_height = 5.6 in (y-extent 2028 px → 362.1 px/in); origin at x min, y max of the outline (x over 0.12–0.45 of the height from the top); Douglas-Peucker at 0.008 in with the extremes kept: 85 points (IoU 0.997 with the full outline); checks: median row width in y [-2.6, -0.7] (2.496–2.496) 2.496 ± 0.045 in vs magpul-pmag-20-gen-m3.front_to_back 2.496 ± 0.045 (corroborated): agrees; width 2.993 ± 0.054; x_min -0.061 ± 0.004; features through the same placement (dots: the right side's dot matrix: its sixty squares (four groups, each three across and five down), each found as the closed white area inside a small drawn square and counted (.cache/pmag20/dots.py), and given as the smallest rectangle round it out to the middle of its stroke) (tools/trace.py)","via":"harvest"},"front":{"plane":"zy","origin":"x center, y max of the outline","offset":{},"points":[[-0.552,-5.068],[-0.539,-5.397],[-0.549,-5.438],[-0.528,-5.498],[-0.423,-5.567],[-0.197,-5.6],[0.194,-5.6],[0.423,-5.567],[0.518,-5.505],[0.533,-5.482],[0.552,-5.202],[0.539,-4.911],[0.468,-4.81],[0.468,-4.247],[0.484,-4.157],[0.479,-2.914],[0.451,-2.765],[0.443,-0.233],[0.419,-0.135],[0.381,-0.08],[0.317,-0.027],[0.238,0],[0.215,-0.012],[0.215,-0.072],[0.201,-0.086],[0.233,-0.098],[0.256,-0.121],[0.254,-0.139],[0.276,-0.117],[0.31,-0.154],[0.281,-0.182],[0.257,-0.166],[0.214,-0.231],[0.189,-0.256],[0.166,-0.257],[0.18,-0.271],[0.135,-0.313],[0.11,-0.313],[0.088,-0.291],[0.067,-0.313],[-0.064,-0.313],[-0.088,-0.288],[-0.113,-0.313],[-0.165,-0.302],[-0.193,-0.273],[-0.171,-0.252],[-0.201,-0.216],[-0.218,-0.159],[-0.218,-0.015],[-0.241,0],[-0.314,-0.024],[-0.363,-0.06],[-0.419,-0.129],[-0.441,-0.192],[-0.446,-0.736],[-0.46,-0.915],[-0.449,-1.331],[-0.477,-1.36],[-0.506,-1.364],[-0.506,-1.484],[-0.449,-1.568],[-0.451,-2.332],[-0.462,-2.349],[-0.451,-2.37],[-0.462,-2.392],[-0.451,-2.414],[-0.454,-2.789],[-0.481,-2.917],[-0.484,-4.198],[-0.468,-4.261],[-0.468,-4.791],[-0.503,-4.862],[-0.549,-4.916],[-0.539,-4.94]],"features":{"bars":[[[0.205,-3.068],[-0.209,-3.068],[-0.209,-3.102],[0.205,-3.102]],[[0.205,-3.223],[-0.209,-3.223],[-0.209,-3.257],[0.205,-3.257]],[[0.205,-3.377],[-0.209,-3.377],[-0.209,-3.409],[0.205,-3.409]],[[0.205,-3.53],[-0.209,-3.53],[-0.209,-3.564],[0.205,-3.564]],[[0.205,-3.685],[-0.209,-3.685],[-0.209,-3.721],[0.205,-3.721]],[[0.205,-4.078],[-0.209,-4.078],[-0.209,-4.111],[0.205,-4.111]],[[0.205,-4.232],[-0.209,-4.232],[-0.209,-4.266],[0.205,-4.266]],[[0.205,-4.384],[-0.209,-4.384],[-0.209,-4.418],[0.205,-4.418]],[[0.205,-4.539],[-0.209,-4.539],[-0.209,-4.572],[0.205,-4.572]],[[0.205,-4.693],[-0.209,-4.693],[-0.209,-4.726],[0.205,-4.726]]]},"scaleRefs":["magpul-pmag-20-gen-m3.overall_height"],"inputs":{"magpul-pmag-20-gen-m3.overall_height":5.6},"tolerance":0.008,"photo":"references/magpul-pmag-20-gen-m3 b1e83c27171f (US D691,233 S (Magpul), FIG. 6 front elevation, 300 dpi)","method":"luminance < 128, inside [600, 620, 1100, 2800], closing ×8, holes filled, inset 2 px (half the outline's stroke); scale from magpul-pmag-20-gen-m3.overall_height = 5.6 in (y-extent 2059 px → 367.7 px/in); origin at x center, y max of the outline; Douglas-Peucker at 0.008 in with the extremes kept: 74 points (IoU 0.995 with the full outline); features through the same placement (bars: the bars across the front strip: five in each of its two rows, each from the middle of its upper line to the middle of its lower one down columns 800 and 850, and from end to end on a row through it (columns 756 and 908.5; the strip they lie on runs from 752 to 912.5). Read as the middles of the ink's runs (.cache/pmag20/meas3.sh, meas4.sh), +/- 1 px) (tools/trace.py)","via":"harvest","note":"A front elevation has the magazine's left on its right: mirrored, so that z is the rifle's (left negative), as a view from the rear has it."},"rear":{"plane":"zy","origin":"x center, y max of the outline","offset":{},"points":[[-0.55,-4.909],[-0.536,-4.933],[-0.55,-5.061],[-0.55,-5.3],[-0.531,-5.479],[-0.424,-5.559],[-0.196,-5.592],[0.217,-5.589],[0.228,-5.6],[0.247,-5.584],[0.424,-5.559],[0.526,-5.49],[0.545,-5.332],[0.55,-5.08],[0.536,-4.901],[0.463,-4.792],[0.463,-4.271],[0.477,-4.184],[0.479,-2.986],[0.474,-2.875],[0.452,-2.763],[0.439,-0.194],[0.411,-0.113],[0.353,-0.054],[0.288,-0.014],[0.228,0],[0.21,-0.02],[0.216,-0.058],[0.189,-0.086],[0.216,-0.115],[0.191,-0.251],[0.152,-0.296],[0.115,-0.289],[0.137,-0.314],[0.148,-0.354],[0.124,-0.387],[0.148,-0.414],[0.117,-0.445],[-0.114,-0.445],[-0.143,-0.417],[-0.121,-0.392],[-0.151,-0.363],[-0.14,-0.352],[-0.143,-0.311],[-0.105,-0.284],[-0.118,-0.268],[-0.105,-0.254],[-0.147,-0.263],[-0.197,-0.224],[-0.219,-0.151],[-0.219,-0.012],[-0.236,0],[-0.312,-0.024],[-0.373,-0.069],[-0.43,-0.162],[-0.444,-0.235],[-0.444,-0.678],[-0.458,-0.889],[-0.449,-1.329],[-0.478,-1.358],[-0.504,-1.362],[-0.501,-1.495],[-0.449,-1.563],[-0.452,-2.763],[-0.479,-2.975],[-0.474,-4.181],[-0.485,-4.192],[-0.468,-4.216],[-0.485,-4.235],[-0.466,-4.254],[-0.466,-4.797]],"features":{"bars":[[[-0.201,-3.306],[0.198,-3.306],[0.198,-3.34],[-0.201,-3.34]],[[-0.201,-3.468],[0.198,-3.468],[0.198,-3.499],[-0.201,-3.499]],[[-0.201,-3.63],[0.198,-3.63],[0.198,-3.664],[-0.201,-3.664]],[[-0.201,-3.795],[0.198,-3.795],[0.198,-3.827],[-0.201,-3.827]],[[-0.201,-3.956],[0.198,-3.956],[0.198,-3.988],[-0.201,-3.988]],[[-0.201,-4.409],[0.198,-4.409],[0.198,-4.438],[-0.201,-4.438]],[[-0.201,-4.569],[0.198,-4.569],[0.198,-4.603],[-0.201,-4.603]],[[-0.201,-4.734],[0.198,-4.734],[0.198,-4.761],[-0.201,-4.761]],[[-0.201,-4.893],[0.198,-4.893],[0.198,-4.924],[-0.201,-4.924]],[[-0.201,-5.055],[0.198,-5.055],[0.198,-5.087],[-0.201,-5.087]]],"rib":[[[-0.075,-3.131],[0.073,-3.131],[0.073,-4.101],[-0.075,-4.101]]]},"scaleRefs":["magpul-pmag-20-gen-m3.overall_height"],"inputs":{"magpul-pmag-20-gen-m3.overall_height":5.6},"tolerance":0.008,"photo":"references/magpul-pmag-20-gen-m3 b1e83c27171f (US D691,233 S (Magpul), FIG. 7 rear elevation, 300 dpi)","method":"luminance < 128, inside [1480, 620, 1980, 2800], closing ×8, holes filled, inset 2 px (half the outline's stroke); scale from magpul-pmag-20-gen-m3.overall_height = 5.6 in (y-extent 2062 px → 368.2 px/in); origin at x center, y max of the outline; Douglas-Peucker at 0.008 in with the extremes kept: 71 points (IoU 0.994 with the full outline); checks: median row width in y [-2.2, -0.7] (0.891–0.953) 0.900 ± 0.018 in vs magpul-pmag-20-gen-m3.width 0.902 ± 0.02 (conflict): agrees; features through the same placement (bars: the bars across the spine under the stop: five in each of its two rows, each from the middle of its upper line to the middle of its lower one down columns 1650 and 1760, and from end to end on a row through it (columns 1629 and 1776; the spine's own edges are at 1623 and 1782.5). In the upper row the long rib down the spine's middle stands over them; rib: the long rib down the middle of the spine's upper row, and the stop's gusset over it at the same width: its two sides on rows 1890 to 2010 (columns 1675.5 and 1730), from under the stop (row 1820.5, down column 1705) to the band under the row (row 2177.5)) (tools/trace.py)","via":"harvest","note":"The rear elevation, seen from behind: z as the rifle's. A check on the front elevation's widths, and where the spine is read."},"left":{"plane":"xy","origin":"the spine's rear face where the top section stands in the well, at the feed lips' top, as the side outline's: the left side, mirrored to face +x","offset":{},"points":[[-0.065,-3.033],[-0.062,-3.141],[0.046,-3.387],[0.143,-4.225],[0.141,-4.279],[0.176,-4.322],[0.181,-4.436],[0.211,-4.566],[0.206,-4.604],[0.227,-4.66],[0.233,-4.769],[0.249,-4.79],[0.262,-4.882],[0.257,-4.917],[0.276,-4.958],[0.289,-5.101],[0.314,-5.177],[0.287,-5.296],[0.303,-5.415],[0.341,-5.55],[0.45,-5.6],[2.819,-5.138],[2.849,-5.13],[2.931,-5.031],[2.912,-4.896],[2.88,-4.777],[2.855,-4.741],[2.801,-4.455],[2.734,-4.022],[2.75,-3.971],[2.731,-3.828],[2.69,-3.784],[2.685,-3.733],[2.696,-3.722],[2.696,-3.687],[2.677,-3.665],[2.666,-3.584],[2.68,-3.565],[2.677,-3.535],[2.658,-3.514],[2.65,-3.441],[2.663,-3.392],[2.639,-3.36],[2.634,-3.268],[2.645,-3.257],[2.639,-3.219],[2.623,-3.203],[2.615,-3.122],[2.628,-3.097],[2.604,-3.006],[2.634,-2.976],[2.62,-2.803],[2.515,-2.703],[2.496,-2.64],[2.493,-0.21],[2.454,-0.184],[1.764,-0.138],[1.713,-0.13],[1.629,-0.092],[1.535,-0.1],[1.521,-0.087],[1.475,-0.103],[1.456,-0.092],[1.416,-0.103],[1.294,-0.095],[1.132,0],[0.18,0],[0.158,-0.008],[0.138,-0.037],[0.141,-0.096],[0.116,-0.261],[0.088,-0.289],[0.062,-0.296],[0.057,-0.418],[0,-0.458],[0,-2.97],[-0.034,-3.004],[-0.055,-3.01]],"features":{"panels_front":[[[2.962,-2.96],[2.343,-3.008],[2.384,-3.828],[3.019,-3.776]],[[3.071,-4.011],[2.459,-4.072],[2.558,-4.746],[3.071,-4.647]]],"panels_middle":[[[2.146,-3.049],[0.904,-3.135],[0.964,-3.987],[2.208,-3.876]]],"panels_rear":[[[0.694,-3.168],[-0.283,-3.243],[-0.283,-4.117],[0.769,-4.036]]],"panel_dots":[[[2.274,-4.092],[-0.174,-4.356],[-0.174,-5.276],[2.371,-4.775]]],"above_frame":[[[2.849,-2.789],[-0.282,-3.008],[-0.282,-2.459],[2.849,-2.459]]],"floorplate_joint":[[[3.119,-4.739],[-0.288,-5.409],[-0.288,-4.541],[3.119,-4.541]]],"catch_notch":[[[1.013,-1.107],[0.491,-1.107],[0.491,-1.359],[1.013,-1.359]]],"catch_block":[[[0.95,-1.359],[0.55,-1.359],[0.55,-1.553],[0.95,-1.553]]],"dots":[[[1.939,-4.729],[2.022,-4.715],[2.008,-4.63],[1.925,-4.644]],[[1.926,-4.631],[2.009,-4.614],[1.992,-4.531],[1.909,-4.547]],[[1.909,-4.535],[1.994,-4.518],[1.977,-4.432],[1.892,-4.449]],[[1.894,-4.436],[1.979,-4.42],[1.963,-4.335],[1.879,-4.351]],[[1.88,-4.337],[1.964,-4.32],[1.947,-4.234],[1.863,-4.252]],[[1.838,-4.743],[1.923,-4.731],[1.911,-4.647],[1.827,-4.658]],[[1.821,-4.645],[1.908,-4.633],[1.896,-4.548],[1.809,-4.56]],[[1.808,-4.546],[1.893,-4.534],[1.881,-4.45],[1.797,-4.462]],[[1.794,-4.449],[1.88,-4.436],[1.867,-4.351],[1.781,-4.364]],[[1.775,-4.35],[1.863,-4.34],[1.853,-4.253],[1.765,-4.263]],[[1.739,-4.758],[1.824,-4.749],[1.814,-4.661],[1.729,-4.671]],[[1.725,-4.66],[1.811,-4.647],[1.799,-4.563],[1.713,-4.575]],[[1.711,-4.562],[1.794,-4.551],[1.782,-4.465],[1.698,-4.476]],[[1.694,-4.464],[1.78,-4.451],[1.768,-4.365],[1.681,-4.377]],[[1.682,-4.364],[1.765,-4.352],[1.753,-4.268],[1.669,-4.28]],[[1.593,-4.783],[1.678,-4.771],[1.665,-4.682],[1.581,-4.694]],[[1.577,-4.681],[1.662,-4.67],[1.651,-4.585],[1.566,-4.596]],[[1.563,-4.587],[1.649,-4.574],[1.636,-4.488],[1.55,-4.5]],[[1.548,-4.485],[1.633,-4.473],[1.621,-4.389],[1.536,-4.401]],[[1.532,-4.387],[1.619,-4.377],[1.609,-4.292],[1.522,-4.302]],[[1.494,-4.795],[1.58,-4.783],[1.568,-4.697],[1.482,-4.71]],[[1.477,-4.698],[1.565,-4.685],[1.553,-4.6],[1.464,-4.612]],[[1.466,-4.599],[1.552,-4.585],[1.538,-4.501],[1.452,-4.515]],[[1.45,-4.501],[1.535,-4.489],[1.523,-4.403],[1.438,-4.415]],[[1.439,-4.405],[1.523,-4.387],[1.505,-4.301],[1.421,-4.319]],[[1.398,-4.812],[1.483,-4.796],[1.467,-4.711],[1.383,-4.727]],[[1.381,-4.711],[1.468,-4.7],[1.457,-4.614],[1.37,-4.625]],[[1.366,-4.613],[1.452,-4.601],[1.44,-4.517],[1.354,-4.529]],[[1.352,-4.515],[1.438,-4.503],[1.426,-4.419],[1.34,-4.431]],[[1.336,-4.416],[1.421,-4.406],[1.41,-4.32],[1.326,-4.331]],[[1.25,-4.834],[1.336,-4.819],[1.321,-4.733],[1.236,-4.747]],[[1.237,-4.737],[1.321,-4.72],[1.304,-4.635],[1.22,-4.652]],[[1.218,-4.636],[1.304,-4.624],[1.292,-4.538],[1.205,-4.55]],[[1.206,-4.537],[1.29,-4.525],[1.277,-4.441],[1.194,-4.453]],[[1.189,-4.439],[1.275,-4.427],[1.263,-4.342],[1.177,-4.354]],[[1.148,-4.848],[1.235,-4.838],[1.225,-4.751],[1.138,-4.761]],[[1.138,-4.749],[1.222,-4.735],[1.208,-4.651],[1.124,-4.665]],[[1.123,-4.653],[1.207,-4.641],[1.195,-4.554],[1.111,-4.566]],[[1.108,-4.555],[1.192,-4.539],[1.177,-4.454],[1.092,-4.469]],[[1.092,-4.456],[1.176,-4.444],[1.164,-4.357],[1.08,-4.369]],[[1.055,-4.864],[1.139,-4.847],[1.123,-4.763],[1.038,-4.78]],[[1.038,-4.764],[1.123,-4.752],[1.111,-4.666],[1.026,-4.678]],[[1.024,-4.666],[1.107,-4.654],[1.095,-4.569],[1.012,-4.581]],[[1.008,-4.567],[1.093,-4.555],[1.081,-4.47],[0.996,-4.482]],[[0.995,-4.472],[1.08,-4.457],[1.065,-4.37],[0.979,-4.386]],[[0.906,-4.885],[0.99,-4.873],[0.978,-4.787],[0.893,-4.799]],[[0.89,-4.786],[0.976,-4.774],[0.964,-4.689],[0.878,-4.701]],[[0.877,-4.689],[0.961,-4.674],[0.946,-4.589],[0.862,-4.604]],[[0.86,-4.59],[0.945,-4.579],[0.934,-4.494],[0.85,-4.504]],[[0.845,-4.492],[0.931,-4.479],[0.918,-4.393],[0.832,-4.406]],[[0.807,-4.899],[0.892,-4.887],[0.879,-4.8],[0.795,-4.813]],[[0.793,-4.803],[0.879,-4.788],[0.865,-4.703],[0.779,-4.717]],[[0.777,-4.703],[0.862,-4.691],[0.85,-4.606],[0.765,-4.618]],[[0.765,-4.607],[0.85,-4.59],[0.833,-4.505],[0.748,-4.522]],[[0.744,-4.504],[0.83,-4.499],[0.824,-4.411],[0.738,-4.417]],[[0.71,-4.915],[0.796,-4.902],[0.784,-4.817],[0.698,-4.829]],[[0.692,-4.814],[0.779,-4.805],[0.769,-4.72],[0.683,-4.729]],[[0.681,-4.721],[0.766,-4.706],[0.751,-4.619],[0.666,-4.635]],[[0.665,-4.62],[0.751,-4.607],[0.739,-4.522],[0.652,-4.535]],[[0.652,-4.523],[0.736,-4.509],[0.721,-4.423],[0.637,-4.438]]]},"scaleRefs":["magpul-pmag-20-gen-m3.overall_height"],"inputs":{"magpul-pmag-20-gen-m3.overall_height":5.6},"tolerance":0.008,"photo":"references/magpul-pmag-20-gen-m3 6ed4a10c5b72 (US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 3 left side elevation, 300 dpi)","method":"luminance < 128, inside [740, 660, 1900, 2800], 1 boxes excluded, closing ×8, holes filled, inset 2 px (half the outline's stroke); scale from magpul-pmag-20-gen-m3.overall_height = 5.6 in (y-extent 2071 px → 369.8 px/in); origin at x min, y max of the outline (x over 0.12–0.45 of the height from the top); Douglas-Peucker at 0.008 in with the extremes kept: 78 points (IoU 0.998 with the full outline); features through the same placement (panels_front: the front column's two panels, each open to the front face: its upper edge, its rear edge and its lower edge, carried well past the front of the outline, so its round corners are the rear two. The upper one is in the grip frame's one row; the lower one is beside the panel with the dot matrix, down to the floorplate; panels_middle: the one large panel, closed all round: where the middles of its four walls would meet; panels_rear: the rear column's one panel, open to the spine: its upper edge, its front edge and its lower edge, carried well past the rear of the outline; panel_dots: the panel under the band, where the dot matrix is: its front edge, its upper edge (the band's lower edge), and down to the floorplate's upper edge, carried past the rear of the outline; above_frame: above the grip frame's upper edge, which runs straight from the front to the stop on the spine: that edge, carried past both ends of the outline, and a third of an inch of the plain side above it. (The tab that the side elevations outline standing up from that edge near the front is left out: the front elevation has nothing standing out of the side at its height.); floorplate_joint: over the floorplate's upper edge, the heavier of the two parallel lines under the dot matrix's panel (the other, 38.5 px over it, is the body's own lower edge): its line through rows 2512, 2551.5, 2591.5, 2630.5 and 2654.5 on columns 1000, 1200, 1400, 1600 and 1720 (the middles of the ink's runs, .cache/pmag20/meas5.sh), carried past both ends of the outline, and a third of an inch above it; catch_notch: the catch's window as drawn: the rounded rectangle, at the middles of its strokes; catch_block: the block drawn under the window, from the window's lower line to its own; dots: the left side's dot matrix: its sixty squares (four groups, each three across and five down), found and counted as the right side's are) (tools/trace.py)","via":"harvest","note":"This magazine's left side as its own design patent draws it: read for where the catch notch, the side panels and the dot matrix are (features). Its outline is the mirror of the side outline's within the two sheets' own scales."}},"gaps":[{"what":"What stands under the catch notch on this magazine (not drawn): its patent's two elevations have a block there 0.057 in out of a side that is as wide as the well already, and Magpul's photo shows its outline","need":"A view of MAG560 from its front or its rear with the left side in profile at the catch notch, or Magpul's own figure (the same question as the 30-round's)"},{"what":"How deep the dot matrix's squares are (drawn 0.016 in, six tenths of the panels' depth), and their size on this magazine itself (the 30-round's photo reading is used; this one's patent draws them larger)","need":"A close view of this magazine's dot matrix, square on with something of known size beside it, and an oblique one lit from one side"},{"what":"The body's width: the patent's elevations scaled by the height give 0.902 in, one seller's table 0.87 in, and Magpul none","need":"Magpul's own figure, or a view from the top or the bottom with something of known size in its plane"},{"what":"What Magpul's 'Length, max' runs between isn't said on its page (taken as the upright height: the top section then matches the 30-round's and the photo); a seller's table has 5.7 in","need":"Magpul's own drawing, or an owner's ruler along it"},{"what":"The feed lips, the bolt catch's relief at the rear of the top, the follower and the floorplate from below are the hull's or not drawn","need":"Tracing the patent's top and bottom plans (FIGS. 4 and 5, on file) and its rear elevation's top: not done in this pass"},{"what":"The over-travel stop's underside in section (ruled faces between the edges the patent draws), and the step Magpul's photograph has in the floorplate's edge near the front (this patent's edge is straight)","need":"A view of MAG560 from below its spine; the left elevation traced again from Magpul's photograph for the edge"},{"what":"The ODG one's number rests on one seller's page (Shiner Tactical: 'Manufacturer Part Number MAG560-ODG'); Magpul's page states none in words","need":"A second seller's page for the green one (Midwest Gun Works' /prod/MAG560-ODG answered 404 on 2026-10-13), or Magpul's"}]},"magpul-pmag-30-gen-m3":{"id":"magpul-pmag-30-gen-m3","name":"PMAG 30 AR/M4 GEN M3","manufacturer":"Magpul","sku":"MAG557","category":"magazine","description":"Magpul's 30-round polymer magazine for AR-15/M4 rifles in 5.56 NATO and .223 Remington, the third generation; the catalog's first 5.56 magazine.","weight":"magpul-pmag-30-gen-m3.weight","cartridge":{"takes":["5.56 NATO",".223 Rem"],"stated":"a 30-round polymer magazine for AR15/M4 compatible weapons chambered in 5.56x45 NATO / .223 Remington","source":"https://magpul.com/media/wysiwyg/GIS/MAG557_PMAG_30_AR_M4_GEN_M3_GIS_01.pdf (Magpul's information sheet for MAG557, as cached: harvest.quote)"},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"magwell":{"origin":["{.spine_ahead_of_stop}","-{.catch_notch_top}",0],"note":"The upper edge of its catch notch, at its spine's rear face where it stands in the well: what hangs on the lower's catch, in the well's spine slot. Until 2026-10-05 it was hung by its feed lips' top where the catalog's .22 magazine's are, 0.37 in too high (its lips above the bore's axis and its top inside the bolt carrier), and by its outline's rearmost point, which is the tip of the stop on the spine under the well and not the spine: 0.07 in too far forward, its front face through the well's front wall. Magazine frame: origin at that tip's X, at the top of the feed lips; the traced side profile uses the same origin."}},"interfaces":{"magwell":{"type":"ar15.magwell","role":"magazine","anchor":"magwell","params":{"family":"5.56"},"flips":false}},"materials":{"body":{"label":"Magazine body","finish":"polymer","recolorable":false,"color":"magpul-black","sheen":"matte","options":{"black":{"label":"Black","finish":"polymer","color":"magpul-black","sheen":"matte","sku":"MAG557-BLK","source":"https://magpul.com/pmag-30-ar-m4-gen-m3.html"},"mct":{"label":"Medium Coyote Tan","finish":"polymer","color":"magpul-mct","sheen":"matte","sku":"MAG557-MCT","source":"https://magpul.com/pmag-30-ar-m4-gen-m3.html"},"mcb":{"label":"Modified Coyote Brown","finish":"polymer","color":"magpul-mcb","sheen":"matte","sku":"MAG557-MCB","source":"https://magpul.com/pmag-30-ar-m4-gen-m3.html"},"odg":{"label":"ODG","finish":"polymer","color":"magpul-odg","sheen":"matte","sku":"MAG557-ODG","source":"https://magpul.com/pmag-30-ar-m4-gen-m3.html"}},"default":"black","note":"The four colours Magpul's page offers MAG557 in (its swatches: Black, Medium Coyote Tan, Modified Coyote Brown, Olive Drab Green; it states MAG557-BLK, -MCT, -MCB and -ODG). Black and ODG are the presets matched on the MOE SL; MCT and MCB were matched on this magazine's and the CTR's own gallery photos (data/colors/magpul.yaml). In every colour the body and the floor plate are one colour (Magpul's gallery shots 01 and 02 of each); the follower is the same light grey in all four (shots 03 of MCT, MCB and ODG, shot 03.1 of black) and isn't drawn: the model is a solid hull, closed at the feed lips. The lock plate shows from below as a light grey button in the floor plate's oval on the black one (Primary Arms' photo, references/magpul-pmag-30-gen-m3 829f3b66d988); no photo of the other three from below is on file, and it isn't drawn either."}},"components":{},"geometry":{"model":"magpul-pmag-30-gen-m3.glb","components":{},"approximations":["A visual hull of Magpul's design patent's side and front elevations (US D681,151 S, FIG. 2 and FIG. 6, drawn for the window model; Magpul's own photo of this one lies on the side outline, IoU 0.987), scaled by Magpul's 7.5 in height: the feed-lip block and top narrower than the body, the floorplate flaring. A curved magazine's section is taken as the front elevation at every height along it, less what the next entries cut from its corners. Where a thing is comes from Magpul's photo of this magazine's left side; what it is in profile, from the patent's elevations.","Its sides (2026-10-05): the grip frame's ribs and bands stand where the front elevation's silhouette is, and between them the panels are cut down to the plane of the plain sides above the frame, as the patent's front and rear elevations show their floors in profile (0.025 in under the frame's face; 0.026 on the left and 0.023 on the right as built, a line's weight in the traced outline). Where the panels are is read on Magpul's photo of this magazine's left side and not on the patent, whose window model has its middle and rear columns stop short of each other round the window: three columns of three, the front ones open to the front and the rear ones to the spine, one rib between the middle and the rear; and under the last band (2026-10-13) the dot matrix's panel, open to the spine, with the small fourth panel of the front column ahead of it across a rib 0.19 in wide, both ending at the body's lower rim, which stands at the frame's face between them and the floorplate's joint (the front elevation's silhouette narrows to a waist over the floorplate, which the hull had along the whole magazine at those heights: it is made without it, so the last band, that rib and the rim keep the frame's face as the photo has them). The right side is the left mirrored (on Primary Arms' photo of the right side the left's readings, mirrored, lie on its own within 0.03 in). Each wall runs 0.026 in from its rim to its floor, as the patent's side view has the two lines round a panel; the panels closed all round and in no view's profile are taken to the same floor as the others.","On the left, the catch's window with its upper edge where the magazine hangs (1.07 in under the lips' top), drawn as a pocket as deep as a lower's catch slot is cut and not through (the model is solid and its wall's thickness isn't read; its corners are as round as the photo shows them, unsized). Under it Magpul's photo shows a rectangle as wide as the window, and the patent's front and rear elevations draw a block there standing 0.054 in out of the side: as read it would stand 0.06 in into the left wall of a standard well under the catch's slot, which a magazine that fits can't, so it is not drawn until that is reconciled (the readings are the ledger's catch_block entries). The hull is made without the ridge that the front elevation's silhouette of the block put down the whole right side until 2026-10-05 (a front elevation has the magazine's left on its right).","The frame's upper edge (2026-10-13) is one straight line from the stop on the spine to the front, as the photo has it behind the tab and ahead of it (read again: its front end 0.04 in lower than first picked). Behind where the side leans in it is the step it was, cut into the frame as the front elevation's silhouette has it (the frame's face comes down to the plain side's toward its upper edge at the front); ahead of that it is the frame's top standing over the leaned side, up to 0.1 in. The tab stands up from it 0.36 in behind the front face, 0.2 in long and 0.5 high: a piece of the side at the side's own width, as the patent's front elevation has its face on the plain side's silhouette and the photo no line across its feet; its two upper corners round (0.03 in), its walls square (the photo has its feet turn out into the edge: not drawn).","The dot matrix (2026-10-13): four blocks of three columns by five rows of square dimples (0.068 in across, 0.101 apart) in the floor of the panel under the last band, on both sides, each block between its four corner dimples as the photo has them. HOW DEEP they are is in no view: they are sunk six tenths of the panels' depth (0.015 in), their walls' shadows being that much weaker than the panel's own on the photo, and their walls lean as far across as that (as a panel's do). Their corners' round isn't drawn.","The grip frame's front and rear (2026-10-13): between the bands the front is a flat strip 0.44 in wide and the rear is the spine's own strip, 0.442 wide, standing 0.07 behind a shoulder, as the patent's front and rear elevations and its side view draw them; the bars are ridges across those strips, one where each tooth is on the photo's silhouette (five, five, five and four down the front; five, five, five and four down the spine), 0.036 in thick and standing 0.017 (front) and 0.022 (spine). Each strip's floor is the side outline's own edge under its teeth, a straight line touching it from inside in each row, and a band's face stands a panel's depth out of the front strip and a bar's height out of the spine (the outline's own bands are within 0.02 in of that). In the spine's second row a rib 0.15 wide runs down the middle from band to band, as far out as the bars, so no side view shows that row's bars: five are drawn across it at the other rows' spacing about the row's middle (ASSUMED where; counted on Primary Arms' view from the rear quarter, as the patent's rear elevation draws them), and the bar behind the stop's gusset one such space above the first that shows. The gusset under the over-travel stop is cut to the rib's width. The bars are plain bars as wide as their strip.","The corners (2026-10-13): each turn of the grip frame from a side to the front strip (beginning 0.115 in behind the front) or to the shoulder beside the spine (over 0.12 in) is drawn as a quarter of an ellipse between the lines the patent's elevations draw at its two ends: ASSUMED, no view has one in section, and the front elevation draws three lines down the front one that a plain round wouldn't have. A band's corner is its row's a panel's depth further out. The last row's corner on each edge is turned only as far down as its strip runs: under that the outline is the floorplate's lip, left square. Above the frame, in the well, the spine's strip stands 0.10 in behind the body's shoulders (it runs in the well's spine slot; until then the model was the body's full width to the spine's rear face, inside a lower's walls beside the slot), and the sides lean in over the last 0.6 in to a front face 0.53 wide, drawn as one flat with a round into the front; on this magazine's photos the lean shows by the two ribs that stand out of it, and where it begins is the patent's. The two ribs keep the side's width to the front face under an upper face that rises at 29 degrees. The floorplate's corners and the feed-lip block's are the hull's own, square, their edges broken at 0.02 in.","The slim groove down each side near the spine (2026-10-13): 0.043 in between its walls, from the line under the feed-lip block to 1.09 in under the top, its ends round. HOW DEEP isn't in any view: as deep as a side panel (0.025 in).","The over-travel stop (2026-10-19): the ledge behind the spine at the grip frame's top, read on the patent's two plans (FIG. 4 and 5, which agree within a pixel) and its rear elevation (FIG. 7). In plan its rear face is flat across the middle (0.304 in each side), its corners round (0.082 in, the round that meets both the flat and the side) and its sides lean out 18 degrees to 0.431 in each side where they meet the frame's top band, 0.206 in ahead of the rear face: narrower than the frame by 0.05 a side, so the band's rear face shows beside it. From the rear its face comes down 0.178 in under the ledge's top (where the ledge meets the spine's face) across the middle and 0.103 toward its ends, straight between the two readings; under its outer parts the underside is ruled from the face's lower edge at the rear to a straight edge at the spine's face, which comes down from 0.156 in under the top (read 0.385 in out) to the spine's edge at the first row's top; under the middle, either side of the gusset, it is hollow up to the face's middle depth, out to a wall from 0.271 in at the rear face to the spine's edge at its face (FIG. 5's line, which reaches that edge there). Where these surfaces meet is the patent's: the underside's ruled faces and the hollows' flat roof are the simplest surfaces between the edges the drawings give (FIG. 8 shows the two hollows; no view has the underside in section). The ledge's top is the hull's (the side outline's, falling 0.04 in from the spine to the tip). The patent is the window model's; MAG557's photos show the same ledge from the rear quarter and the side, and are not measured for it.","The floorplate's joint (2026-10-19): along the joint the photo draws (rim_low's lower edge, with its step near the front) the body's rim stands at the frame's face, and under it the floorplate's side is the front elevation's at the floorplate's front end, carried along the joint: from the waist's top (where the patent's side elevation has the floorplate's top at the front), at the waist's width (0.457 and 0.46 in, 0.026 and 0.023 in under the rim's face: the dark seam along the joint on the photo), for 0.12 in, then the flare out to the floorplate's widest (the outline's own corners each side). The front elevation is a silhouette, and is read as the floorplate's section at its front end: on the photo the floorplate stands 0.33 in under the joint all along, where the section reaches its widest at 0.38, and its face darkens from about 0.2 in under the joint as the flare's would. Until then the floorplate stood out of the rim at the hull's full width with a square shoulder, the flare being carried at the heights it has at the front.","Not drawn: the markings and the round counter's marks, the floorplate's texture, its pockets and its own corners, the body's tongue ahead of the joint's step standing in from the floorplate's top (the photo has a lit edge there; drawn at the rim's face), the two small slots at the top of the spine, the dimples' round corners, the follower and the lock plate (the model is solid)."],"ledger":["magpul-pmag-30-gen-m3.overall_height","magpul-pmag-30-gen-m3.body_height","magpul-pmag-30-gen-m3.feed_lip_block_height","magpul-pmag-30-gen-m3.front_to_back","magpul-pmag-30-gen-m3.hang_below_magwell","magpul-pmag-30-gen-m3.catch_notch_top","magpul-pmag-30-gen-m3.catch_notch_height","magpul-pmag-30-gen-m3.catch_notch_rear_x","magpul-pmag-30-gen-m3.catch_notch_front_x","magpul-pmag-30-gen-m3.side_panel_depth","magpul-pmag-30-gen-m3.side_panel_wall_run","magpul-pmag-30-gen-m3.side_panel_corner_radius","magpul-pmag-30-gen-m3.frame_tab_corner_radius","magpul-pmag-30-gen-m3.dot_matrix_blocks","magpul-pmag-30-gen-m3.dot_matrix_columns","magpul-pmag-30-gen-m3.dot_matrix_rows","magpul-pmag-30-gen-m3.dot_matrix_pitch","magpul-pmag-30-gen-m3.dot_matrix_dimple","magpul-pmag-30-gen-m3.front_bar_proud","magpul-pmag-30-gen-m3.spine_bar_proud","magpul-pmag-30-gen-m3.strip_bar_thickness","magpul-pmag-30-gen-m3.front_strip_width","magpul-pmag-30-gen-m3.front_corner_depth","magpul-pmag-30-gen-m3.spine_strip_width","magpul-pmag-30-gen-m3.spine_rib_width","magpul-pmag-30-gen-m3.spine_strip_proud","magpul-pmag-30-gen-m3.rear_corner_depth","magpul-pmag-30-gen-m3.rear_shoulder_width","magpul-pmag-30-gen-m3.spine_strip_proud_upper","magpul-pmag-30-gen-m3.upper_rear_corner_radius","magpul-pmag-30-gen-m3.nose_taper_length","magpul-pmag-30-gen-m3.nose_round_depth","magpul-pmag-30-gen-m3.nose_shoulder_width","magpul-pmag-30-gen-m3.nose_front_width","magpul-pmag-30-gen-m3.guide_rib_top_angle","magpul-pmag-30-gen-m3.stop_flat_half_width","magpul-pmag-30-gen-m3.stop_side_angle","magpul-pmag-30-gen-m3.stop_half_width","magpul-pmag-30-gen-m3.stop_length","magpul-pmag-30-gen-m3.stop_lip_depth_middle","magpul-pmag-30-gen-m3.stop_lip_level_half_width","magpul-pmag-30-gen-m3.stop_lip_depth_end","magpul-pmag-30-gen-m3.stop_lip_end_half_width","magpul-pmag-30-gen-m3.stop_wing_depth","magpul-pmag-30-gen-m3.stop_wing_half_width","magpul-pmag-30-gen-m3.stop_bay_half_width"]},"profiles":{"side":{"plane":"xy","origin":"the outline's rearmost point (the tip of the stop on the spine just under the magwell: the spine's rear face in the well is spine_ahead_of_stop ahead of it) at the feed lips' top","offset":{},"points":[[0,-3.164],[0.141,-3.49],[0.13,-3.536],[0.15,-3.562],[0.162,-3.617],[0.144,-3.666],[0.15,-3.704],[0.17,-3.724],[0.179,-3.805],[0.164,-3.828],[0.196,-3.949],[0.182,-3.998],[0.211,-4.059],[0.202,-4.088],[0.211,-4.096],[0.188,-4.142],[0.231,-4.402],[0.237,-4.469],[0.225,-4.48],[0.251,-4.541],[0.378,-5.352],[0.387,-5.38],[0.421,-5.415],[0.439,-5.464],[0.424,-5.493],[0.462,-5.6],[0.459,-5.686],[0.485,-5.715],[0.496,-5.787],[0.485,-5.802],[0.531,-5.926],[0.519,-5.972],[0.548,-6.015],[0.56,-6.07],[0.551,-6.125],[0.586,-6.188],[0.571,-6.212],[0.586,-6.232],[0.566,-6.258],[0.586,-6.327],[0.571,-6.35],[0.6,-6.382],[0.609,-6.437],[0.658,-6.489],[0.649,-6.529],[0.693,-6.639],[0.69,-6.702],[0.733,-6.797],[0.724,-6.843],[0.765,-6.89],[0.785,-6.959],[0.765,-6.988],[0.768,-7.011],[0.808,-7.054],[0.834,-7.144],[0.805,-7.187],[0.863,-7.4],[0.988,-7.48],[1.026,-7.497],[1.066,-7.491],[1.075,-7.5],[1.112,-7.474],[1.306,-7.419],[1.329,-7.431],[1.378,-7.399],[3.314,-6.851],[3.36,-6.831],[3.417,-6.777],[3.437,-6.728],[3.443,-6.65],[3.394,-6.486],[3.402,-6.465],[3.366,-6.424],[3.337,-6.421],[3.304,-6.388],[3.307,-6.338],[3.278,-6.301],[3.264,-6.235],[3.235,-6.197],[3.215,-6.131],[3.244,-6.093],[3.232,-6.056],[3.206,-6.03],[3.194,-5.972],[3.209,-5.955],[3.2,-5.914],[3.171,-5.88],[3.169,-5.854],[3.192,-5.831],[3.186,-5.787],[3.154,-5.663],[3.114,-5.629],[3.105,-5.597],[3.119,-5.577],[3.079,-5.487],[3.076,-5.455],[3.091,-5.438],[3.082,-5.404],[3.053,-5.369],[3.056,-5.285],[3.018,-5.199],[3.033,-5.167],[3.021,-5.126],[2.998,-5.103],[2.99,-5.049],[3.004,-5.034],[3.001,-5.005],[2.969,-4.939],[2.992,-4.904],[2.972,-4.783],[2.987,-4.757],[2.929,-4.705],[2.923,-4.685],[2.929,-4.61],[2.906,-4.587],[2.894,-4.541],[2.912,-4.515],[2.909,-4.466],[2.88,-4.437],[2.883,-4.33],[2.857,-4.298],[2.851,-4.261],[2.866,-4.229],[2.837,-4.16],[2.834,-4.125],[2.848,-4.111],[2.814,-3.998],[2.842,-3.964],[2.828,-3.834],[2.819,-3.799],[2.779,-3.756],[2.788,-3.672],[2.77,-3.655],[2.762,-3.588],[2.776,-3.554],[2.744,-3.47],[2.762,-3.418],[2.759,-3.395],[2.733,-3.366],[2.727,-3.32],[2.747,-3.291],[2.741,-3.257],[2.721,-3.233],[2.715,-3.17],[2.73,-3.153],[2.704,-3.066],[2.704,-3.04],[2.73,-3.008],[2.718,-2.832],[2.617,-2.743],[2.594,-2.694],[2.594,-0.302],[2.586,-0.203],[2.547,-0.182],[1.41,-0.104],[1.291,-0.052],[1.222,0],[0.232,0],[0.205,-0.03],[0.208,-0.085],[0.167,-0.414],[0.134,-0.447],[0.079,-0.447],[0.066,-0.46],[0.069,-2.994],[0.036,-3.036],[0.006,-3.046]],"scaleRefs":["magpul-pmag-30-gen-m3.overall_height"],"inputs":{"magpul-pmag-30-gen-m3.overall_height":7.5},"tolerance":0.008,"photo":"references/magpul-pmag-30-gen-m3 e9f276159e55 (US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 2 right side elevation, 300 dpi)","method":"luminance < 128, inside [600, 420, 1860, 3080], 1 boxes excluded, closing ×8, holes filled, inset 2 px (half the outline's stroke); scale from magpul-pmag-30-gen-m3.overall_height = 7.5 in (y-extent 2599 px → 346.5 px/in); origin at x min, y max of the outline; Douglas-Peucker at 0.008 in with the extremes kept: 167 points (IoU 0.998 with the full outline) (tools/trace.py)","via":"harvest"},"front":{"plane":"zy","origin":"x center, y max of the outline","offset":{},"points":[[-0.586,-7.283],[-0.574,-7.366],[-0.526,-7.417],[-0.468,-7.451],[-0.332,-7.491],[-0.262,-7.5],[-0.219,-7.488],[0.225,-7.488],[0.277,-7.5],[0.489,-7.442],[0.559,-7.385],[0.58,-7.348],[0.586,-6.788],[0.577,-6.729],[0.531,-6.628],[0.46,-6.532],[0.46,-6.409],[0.475,-6.387],[0.488,-6.249],[0.479,-2.91],[0.488,-2.901],[0.46,-2.839],[0.457,-1.586],[0.509,-1.51],[0.512,-1.399],[0.508,-1.379],[0.489,-1.376],[0.457,-1.343],[0.463,-0.903],[0.451,-0.712],[0.451,-0.226],[0.432,-0.152],[0.386,-0.075],[0.335,-0.034],[0.243,0],[0.22,-0.011],[0.223,-0.14],[0.202,-0.192],[0.192,-0.269],[0.154,-0.311],[0.012,-0.314],[-0.02,-0.282],[-0.028,-0.243],[-0.049,-0.265],[-0.066,-0.254],[-0.038,-0.282],[-0.071,-0.314],[-0.111,-0.305],[-0.12,-0.314],[-0.132,-0.302],[-0.148,-0.314],[-0.183,-0.279],[-0.171,-0.263],[-0.205,-0.229],[-0.183,-0.208],[-0.22,-0.174],[-0.217,-0.014],[-0.246,0],[-0.329,-0.031],[-0.386,-0.075],[-0.423,-0.131],[-0.448,-0.205],[-0.457,-2.818],[-0.488,-2.95],[-0.479,-3.141],[-0.488,-4.132],[-0.479,-4.963],[-0.488,-5.166],[-0.479,-5.972],[-0.488,-6.003],[-0.488,-6.249],[-0.479,-6.258],[-0.472,-6.397],[-0.457,-6.412],[-0.457,-6.511],[-0.546,-6.658],[-0.583,-6.763]],"scaleRefs":["magpul-pmag-30-gen-m3.overall_height"],"inputs":{"magpul-pmag-30-gen-m3.overall_height":7.5},"tolerance":0.008,"photo":"references/magpul-pmag-30-gen-m3 21cdc684d6f3 (US D681,151 S (Magpul), FIG. 6 front elevation, 300 dpi)","method":"luminance < 128, inside [570, 440, 1005, 2930], closing ×8, holes filled, inset 2 px (half the outline's stroke); scale from magpul-pmag-30-gen-m3.overall_height = 7.5 in (y-extent 2437 px → 324.9 px/in); origin at x center, y max of the outline; Douglas-Peucker at 0.008 in with the extremes kept: 77 points (IoU 0.994 with the full outline) (tools/trace.py)","via":"harvest"},"left":{"plane":"xy","origin":"the photo's rearmost point (the tip of the stop on the spine) at the feed lips' top, as the side outline's: the left side, mirrored to face +x","offset":{},"points":[[0,-3.067],[0.005,-3.159],[0.03,-3.184],[0.128,-3.434],[0.154,-3.473],[0.138,-3.511],[0.164,-3.543],[0.172,-3.606],[0.153,-3.672],[0.177,-3.697],[0.19,-3.795],[0.172,-3.819],[0.175,-3.84],[0.199,-3.858],[0.211,-3.949],[0.193,-3.973],[0.212,-4.006],[0.222,-4.082],[0.2,-4.128],[0.272,-4.666],[0.393,-5.354],[0.434,-5.398],[0.434,-5.497],[0.457,-5.516],[0.471,-5.62],[0.461,-5.65],[0.485,-5.668],[0.502,-5.744],[0.489,-5.803],[0.522,-5.841],[0.534,-5.925],[0.523,-5.955],[0.558,-6],[0.569,-6.084],[0.559,-6.113],[0.583,-6.132],[0.595,-6.173],[0.576,-6.239],[0.58,-6.267],[0.612,-6.398],[0.646,-6.443],[0.654,-6.506],[0.644,-6.536],[0.677,-6.567],[0.691,-6.622],[0.687,-6.694],[0.711,-6.712],[0.728,-6.844],[0.754,-6.876],[0.769,-6.931],[0.763,-6.996],[0.797,-7.034],[0.805,-7.097],[0.777,-7.257],[0.846,-7.454],[0.955,-7.5],[1.137,-7.476],[1.87,-7.27],[1.951,-7.238],[2.014,-7.23],[2.15,-7.183],[2.83,-7.006],[3.282,-6.874],[3.328,-6.847],[3.402,-6.741],[3.39,-6.7],[3.374,-6.688],[3.392,-6.664],[3.381,-6.53],[3.299,-6.342],[3.3,-6.299],[3.27,-6.232],[3.26,-6.155],[3.226,-6.068],[3.227,-6.018],[3.195,-5.937],[3.195,-5.887],[3.166,-5.827],[3.174,-5.783],[3.166,-5.72],[3.142,-5.652],[3.107,-5.6],[3.106,-5.543],[3.077,-5.483],[3.062,-5.372],[3.037,-5.297],[3.037,-5.24],[3.02,-5.221],[3.004,-5.102],[2.98,-5.027],[2.978,-4.963],[2.958,-4.916],[2.973,-4.871],[2.955,-4.739],[2.909,-4.66],[2.915,-4.595],[2.897,-4.569],[2.888,-4.449],[2.864,-4.374],[2.872,-4.33],[2.853,-4.297],[2.843,-4.221],[2.854,-4.198],[2.828,-4.166],[2.82,-4.103],[2.828,-4.059],[2.811,-4.033],[2.802,-3.97],[2.82,-3.946],[2.799,-3.786],[2.775,-3.768],[2.779,-3.746],[2.762,-3.727],[2.778,-3.682],[2.761,-3.663],[2.748,-3.565],[2.759,-3.542],[2.74,-3.509],[2.741,-3.409],[2.715,-3.321],[2.73,-3.276],[2.709,-3.222],[2.702,-3.173],[2.717,-3.128],[2.693,-3.053],[2.713,-2.987],[2.7,-2.839],[2.681,-2.806],[2.65,-2.789],[2.608,-2.738],[2.585,-2.67],[2.574,-2.38],[2.585,-2.3],[2.58,-2.109],[2.569,-2.082],[2.582,-1.696],[2.57,-1.505],[2.576,-0.651],[2.566,-0.575],[2.567,-0.425],[2.58,-0.359],[2.564,-0.191],[2.536,-0.17],[2.493,-0.161],[2.248,-0.137],[1.732,-0.107],[1.672,-0.087],[1.445,-0.089],[1.304,-0.051],[1.22,-0.005],[1.049,0],[0.609,-0.009],[0.295,-0.002],[0.218,-0.012],[0.204,-0.039],[0.197,-0.196],[0.177,-0.263],[0.184,-0.312],[0.172,-0.434],[0.157,-0.454],[0.08,-0.464],[0.073,-0.49],[0.075,-0.718],[0.088,-0.815],[0.074,-0.867],[0.073,-1.017],[0.081,-1.079],[0.068,-2.041],[0.076,-2.943],[0.07,-3.008],[0.055,-3.028],[0.014,-3.04]],"features":{"panels_front":[[[2.942,-2.975],[2.393,-3.044],[2.496,-3.812],[3.046,-3.749]],[[3.072,-3.942],[2.523,-4.011],[2.626,-4.776],[3.174,-4.702]],[[3.201,-4.9],[2.707,-4.957],[2.808,-5.704],[3.301,-5.647]]],"panels_middle":[[[2.2,-3.059],[0.961,-3.155],[1.072,-3.982],[2.304,-3.834]],[[2.325,-4.045],[1.092,-4.207],[1.202,-5.024],[2.432,-4.841]],[[2.507,-5.027],[1.246,-5.218],[1.342,-5.937],[2.604,-5.749]]],"panels_rear":[[[0.731,-3.189],[-0.111,-3.274],[-0.004,-4.065],[0.819,-3.974]],[[0.855,-4.243],[0.035,-4.358],[0.146,-5.183],[0.958,-5.064]],[[1.055,-5.279],[0.175,-5.402],[0.287,-6.23],[1.152,-6.105]]],"panel_dots":[[[2.688,-5.969],[0.324,-6.509],[0.412,-7.161],[2.837,-6.507]]],"above_frame":[[[2.952,-2.786],[2.397,-2.83],[2.363,-2.324],[2.156,-2.327],[2.195,-2.846],[-0.179,-3.033],[-0.311,-2.049],[2.855,-2.064]]],"panel_front_low":[[[3.396,-5.82],[2.873,-5.89],[3.028,-6.537],[3.489,-6.512]]],"rim_low":[[[3.489,-6.512],[3.028,-6.537],[2.837,-6.507],[0.412,-7.161],[0.432,-7.309],[2.866,-6.637],[2.901,-6.847],[3.507,-6.645]]],"dot_blocks":[[[1.079,-6.465],[1.277,-6.414],[1.377,-6.805],[1.18,-6.855]],[[1.423,-6.376],[1.619,-6.326],[1.718,-6.714],[1.523,-6.764]],[[1.763,-6.286],[1.962,-6.235],[2.062,-6.624],[1.864,-6.675]],[[2.105,-6.191],[2.301,-6.141],[2.402,-6.533],[2.206,-6.584]]],"spine_groove":[[[0.446,-0.21],[0.489,-0.21],[0.489,-1.09],[0.446,-1.09]]],"guide_ribs":[[[1.85,-0.455],[2.75,-0.455],[2.75,-0.603],[1.85,-0.603]],[[1.85,-1.985],[2.75,-1.985],[2.75,-2.12],[1.85,-2.12]]],"bars_front":[[[2.711,-3.126],[2.724,-3.264],[2.739,-3.402],[2.754,-3.538],[2.772,-3.684]],[[2.827,-4.062],[2.847,-4.198],[2.866,-4.332],[2.89,-4.47],[2.914,-4.608]],[[2.981,-4.978],[3.003,-5.13],[3.033,-5.258],[3.065,-5.39],[3.094,-5.528]],[[3.186,-5.886],[3.22,-6.026],[3.253,-6.155],[3.292,-6.288]]],"bars_spine":[[[0.142,-3.516],[0.159,-3.672],[0.178,-3.828],[0.194,-3.982]],[[0.431,-5.484],[0.461,-5.64],[0.493,-5.792],[0.525,-5.946],[0.559,-6.102]],[[0.65,-6.526],[0.689,-6.686],[0.727,-6.834],[0.765,-6.986]]]},"scaleRefs":["magpul-pmag-30-gen-m3.overall_height"],"inputs":{"magpul-pmag-30-gen-m3.overall_height":7.5},"tolerance":0.008,"photo":"references/magpul-pmag-30-gen-m3 3eded591002b (Magpul's own photo of MAG557's left side (gallery _02.1, black), on white, 1200 px, the magazine leaning 7.7°)","method":"luminance < 200, closing ×2, largest piece, holes filled; rotated +7.7° as declared; scale from magpul-pmag-30-gen-m3.overall_height = 7.5 in (y-extent 1064 px → 141.9 px/in); origin at x min, y max of the outline; Douglas-Peucker at 0.008 in with the extremes kept: 172 points (IoU 0.997 with the full outline); features through the same placement (panels_front: the front column's three panels, each open to the front face between two bands: its upper edge, its rear edge (the rib between it and the middle column) and its lower edge, carried well past the front of the outline (the photo's front edge is at columns 420 to 440 there), so its round corners are the rear two; panels_middle: the middle column's three large panels, closed all round: where the dark lines of their four edges would meet; panels_rear: the rear column's three panels, each open to the spine between two bands: its upper edge, its front edge (the one rib between it and the middle column) and its lower edge, carried well past the rear of the outline (the spine is at columns 790 to 800 there); panel_dots: the panel under the last band, where the dot matrix is (read again 2026-10-13, each edge as the middle of its dark line on profiles across it, .cache/detail/magpul-pmag-30-gen-m3/prof.py): its front edge (columns 488.8, 485.4, 482.8 on rows 964, 986, 1008: it leans as the body does, where the first pick stood upright in the photo), its upper edge (the band's lower edge: rows 961.6, 953.6, 944.7, 939.1 at columns 751, 665, 577, 505), its lower edge (the upper edge of the rim that stands between it and the floorplate's joint: rows 1021.0, 1035.4, 1045.5 at columns 516, 633, 706; the first pick ran it down to the joint), carried past the rear of the outline; above_frame: above the grip frame's upper edge, with the tab that stands up from it near the front (2026-10-13, the same way): the edge is one straight line from the stop on the spine to the front, behind the tab and ahead of it (the middle of its dark line at columns 743.5, 672.5, 601.4, 530.3 and, ahead of the tab, 459.3, 452.2: rows 476.2, 480.3, 484.0, 488.0, 491.8, 492.5, all within half a pixel of one line; the first pick had its front end 6 px high), carried past both ends of the outline; the tab's front side (columns 470.0, 471.3, 472.5 on rows 433, 451, 470), its top (rows 416.8, 417.4, 418.8 at columns 489, 481, 472: level across the magazine) and its rear side (columns 499.0, 500.5, 501.2), each corner where two of those lines meet; and the plain side above. The corners run: the edge's front end, the tab's front foot, its front top, its rear top, its rear foot, the edge's rear end, and two above; panel_front_low: the small fourth panel of the front column, under the last band and ahead of the dot matrix's: its upper edge (rows 930.5, 930.3 at columns 444, 432), its rear edge (columns 461.0, 458.4, 456.5 on rows 968, 990, 1012: a rib 0.19 in wide stands between it and the dot matrix's panel) and its lower edge (rows 1022.8, 1025.3, 1026.2 at columns 473, 445, 431), carried past the front of the outline; rim_low: the body's lower rim, between those two panels' lower edges and the joint the floorplate's upper edge makes (the black line: rows 1040.5, 1046.7, 1057.2, 1067.8, 1074.4 at columns 519, 563, 636, 709, 767, and ahead of its step at column 479 rows 1057.1, 1060.0 at columns 435, 450), carried past both ends of the outline; dot_blocks: the dot matrix: four blocks of three columns by five rows of square dimples (Magpul's own diagram of it, references/magpul-pmag-30-gen-m3/docs/d31fc37728.pdf, has every character on such a block), each block as the middles of its four corner dimples: rear upper, front upper, front lower, rear lower. Along the rows (a profile 0.4 in wide down the matrix's length, 14.45 degrees to the magazine's level: the joint's own lean) each dimple is a lit wall then a dark one 0.067 in on, twelve of each; down each block's middle column a dark wall (the dimple's upper one) every 0.100 to 0.101 in, five of them, 0.034 above the dimple's middle; spine_groove: the slim groove down the side near the spine: its two walls' dark lines (0.446 and 0.489 in from the outline's rearmost point on four lines across it), from where it leaves the line under the feed-lip block to its lower end (the dark stops at row 209); guide_ribs: the two ribs that stand at the side's own width where the body narrows toward its front face: each one's flat face, from under its sloped upper face (the dark wedge whose middle is 0.441, 0.434, 0.418 in under the top at 2.3, 2.4, 2.5 in from the rear for the upper rib, and 1.969, 1.966, 1.959 for the lower; a wedge because the face leans in as the body narrows) down to its lower edge (0.603; 2.114 to 2.128), carried behind where the narrowing begins and past the front of the outline; bars_front: the front strip's bars, as the teeth they are on the silhouette's front edge (the edge found to a quarter pixel along lines of constant height, a tooth where it stands 0.009 to 0.02 in out of the edge beside it): each row's teeth from the top, the middle of each tooth at its top. The first two rows are this photo's own (each within 0.012 in of the same tooth on Primary Arms' photo of the right side, 8664c534ce73). In the third and fourth its edge is softened by the cut-out (teeth 0.009 to 0.012 in high, two of the fourth row's not found): the third row's are between this photo's and that one's readings, which are within 0.018 of each other, and the fourth row's four are that photo's (5.892, 6.032, 6.142, 6.276 in under the top there), moved 0.006 to 0.013 toward the two this photo does show (6.030, 6.290). Five, five, five and four, as Primary Arms' view of the front has them (53b35012a3a4); the patent's window model has three and a block in the last row; bars_spine: the spine's bars the same way, on the silhouette's rear edge: the row under the over-travel stop (four teeth: a fifth bar above them is behind the stop's gusset from the side), the row under the long rib (five) and the last row (four). The row between, where the rib stands, shows no tooth from the side: the rib is as far out as the bars) (tools/trace.py)","via":"harvest","note":"This magazine's own left side: read for where its side panels are (features). Its outline is the photo's silhouette, which lies on the patent's side outline (IoU 0.987); the model's outline is the patent's."}},"gaps":[{"what":"What stands under the catch notch on this magazine (not drawn): the patent's two elevations have a block there 0.054 in out of a side that is as wide as the well already, and Magpul's photo shows its outline","need":"A view of MAG557 from its front or its rear with the left side in profile at the catch notch, or Magpul's own figure"},{"what":"The side panels' depth on this magazine itself","need":"The same view lower down: it is the window model's drawing that shows the panels' floors in profile, and this magazine's photos show them only obliquely"},{"what":"How deep the dot matrix's dimples and the groove near the spine are (drawn 0.015 and 0.025 in: assumed)","need":"A view along the side from close by with either in profile, or Magpul's own figure"},{"what":"The grip frame's corners in section (drawn as quarter ellipses between the patent's lines), where the upper body's lean begins on this magazine (the patent's 0.6 in behind the front: neither side photo has a line there), and how wide the front strip and the spine are on it (the patent's window model's)","need":"MAG557 from straight above and below, or from its front and its rear, square on"},{"what":"Where the spine's second row has its five bars, and the one behind the stop's gusset (drawn at the other rows' spacing: no side view shows them)","need":"A view of MAG557's spine, square on"},{"what":"The over-travel stop's underside in section (its outer parts' ruled faces and the hollows' flat roof are the simplest surfaces between the edges the patent draws), and the stop on this magazine rather than the window model's drawing","need":"A view of MAG557 from below its spine, or from the rear with the stop's underside lit"},{"what":"The floorplate's section along its sides (the front elevation's at its front end, carried along the joint) and the body's tongue ahead of the joint's step","need":"A view of MAG557 from the front or the rear, square on, low enough to see the floorplate's side in profile"}]},"magpul-pmag-d-60":{"id":"magpul-pmag-d-60","name":"PMAG D-60 AR/M4 GEN M3","manufacturer":"Magpul","sku":"MAG576","url":"https://magpul.com/pmag-d-60-ar-m4-gen-m3.html","category":"magazine","description":"Magpul's 60-round polymer drum for AR-15/M4 rifles in 5.56 NATO and .223 Remington: a GEN M3 feed tower on a drum 4.1 in across, with a ratcheting loading lever on its front cover and a round-count window and a paint-pen dot matrix on its rear. Its slip-on dust cover comes off before it goes into a rifle and is not drawn.","weight":"magpul-pmag-d-60.weight","cartridge":{"takes":["5.56 NATO",".223 Rem"],"stated":"Caliber 5.56x45mm / .223 Remington ... Optimized for use only with 5.56x45 NATO/.223 Remington cartridges. Use with other calibers such as .300 AAC Blackout is not recommended.","source":"https://magpul.com/pmag-d-60-ar-m4-gen-m3.html (Magpul's technical specifications for MAG576 and the note under them, as cached: harvest.quote)"},"rounds":{"capacity":"magpul-pmag-d-60.capacity","each":"magpul-pmag-d-60.round_weight"},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"magwell":{"origin":[0,"-{.catch_notch_top}",0],"note":"The upper edge of its catch notch, at its spine's rear face where it stands in the well: what hangs on the lower's catch, in the well's spine slot. Magazine frame: origin at the rear face of the feed tower's spine at the top of the feed lips, the tower upright (as a well holds it: std.ar15.magwell_wall_lean); the drum then hangs nose up by tower_lean, its roof and the stop on it under the well's mouth. The notch's height is this part's own: the ledge under it on its own rear photo (catch_notch_lower_edge), which is where Magpul's 30-round GEN M3 has it."}},"interfaces":{"magwell":{"type":"ar15.magwell","role":"magazine","anchor":"magwell","params":{"family":"5.56"},"flips":false,"note":"Magpul: 'Wide compatibility with most STANAG 4179 platforms such as the AR15, M4, M16 ...'; 'Will seat fully loaded on a closed bolt'; its sheet (072-0113-B): 'Ensure that the Loading Lever is in the stowed position prior to inserting the D-60 into the magazine well.'"}},"materials":{"body":{"label":"Drum and feed tower","finish":"polymer","recolorable":false,"color":"magpul-black","sheen":"matte","options":{"black":{"label":"Black","finish":"polymer","color":"magpul-black","sheen":"matte","sku":"MAG576-BLK","source":"https://magpul.com/pmag-d-60-ar-m4-gen-m3.html"}},"default":"black","note":"Sold in black only: Magpul's page has one choice under Color, Black, and MAG576-BLK is the number on every seller's page read. Every piece the model draws but the window is that black plastic in Magpul's and Primary Arms' photos (\"Next-generation impact and crush resistant polymer construction\"): the drum's body, its front and rear covers, the feed tower, the four retaining clips, the loading lever. What shows of another colour and isn't drawn: a round's brass and the bright coiled link of the follower beside it at the feed lips (Magpul's gallery picture is of a loaded magazine), and the dust cover, also black, which comes off before use."},"window":{"label":"Round-count window","finish":"translucent_polymer","recolorable":false,"color":"magpul-d60-window","note":"\"Anti-glare translucent window on rear of drum allows for easy determination of rounds remaining\" (Magpul): a see-through plastic pane in the rear cover with the numerals 10 to 60 moulded in it, smoother and a little glossier than the body round it in Primary Arms' photo of the empty magazine from the rear, and showing the rounds' brass in Magpul's close-up of a loaded one. Drawn as a pane over the body's black (the drum's inside, its follower and any round aren't drawn), so it reads as a dark glossy window; the app's translucent plastic is glossy, where Magpul calls this one anti-glare. Its numerals aren't drawn."}},"components":{},"geometry":{"model":"magpul-pmag-d-60.glb","components":{},"approximations":["The drum is a hull of two views made round: Magpul's design patent's left side elevation (US D765,813 S, FIG. 4, its solid lines below the feed tower, scaled by Magpul's 4.1 in across through the rear elevation) and the studio photo of the product from the rear (scaled by the 7.4 in and the 4.1 in, which agree on it within 0.2%). Its body is taken as round about one axis, half the 4.1 in above its lowest point (the rear photo's hub is within 0.05 in of that, the patent's front elevation's within 0.01), its radius along the axis the side elevation's lower edge: 2.05 in at the rear cover, 1.84 at the front.","The four retaining clips are the rear photo's ears at the diagonals, each carried the drum's whole length within 13.6 degrees either side of its diagonal, and standing on the body from 1.56 in out; the roof under the tower, the stop under the well and the front cover's upper edge are the side elevation's own top edge carried across the width the rear photo has at each height. The loading lever, stowed, is its eye (with its hole) and its tapering arm as the patent's front elevation outlines them (FIG. 2, picked ± 0.03 in), flat faced and standing out to the side elevation's front edge: as thick as the rim's corner it lies in, where the real one is a thin arm in a channel.","The feed tower is not taken from the patent, which draws it in broken lines, about 0.2 in short at the top and a little small (its figure is 1.757 as tall as wide, the product's photo 1.804). It is Magpul's GEN M3 tower: the side outline of the catalog's 30-round GEN M3 (its own design patent's) from the feed lips down into the roof, at this part's own width (0.875 in on its rear photo). Its spine is 0.46 in wide (the photo) and as deep as a magazine well's slot for it (the Army's .155); the gap between its feed lips is the rear photo's, which is of a loaded magazine (0.44 in wide, its floor 0.31 in down, where a round or the follower would be).","It stands on the drum where two sources put it: its top where the rear photo has it (7.4 in over the drum's lowest point as the drum stands with its faces upright, the tower leaning away from the lens), its spine's rear face 0.086 in ahead of the drum's rearmost point at the roof and leaning forward 10 degrees as it rises (the patent's broken lines: the only side view). In the part's frame the tower is upright, so the drum hangs nose up by those 10 degrees and the magazine is 7.36 in from the lips to its lowest point.","The catch's window on the tower's left is where this part's own photo has the ledge under it (1.35 in under the lips; the window's upper edge 1.10, the 30-round's being 1.07), as long and as tall as the 30-round's, a pocket as deep as a lower's catch slot is cut and not through. The block that stands out of the left side under it (0.05 in on the rear photo) is not drawn, as on the 30-round: with it a tower as wide as this one would stand in a well's left wall under the catch's slot.","On the rear cover, placed about the hub (which is put on the drum's axis): the round-count window in its recess, the hub's round depression with its boss, and the dot matrix's sixty squares (five rows of four groups of three, counted). On the front cover: its hub's face and the two full circles the patent's front elevation draws round it. Round the body: the two covers' seams. Every one of these is a relief 0.025 in deep, Magpul's moulded relief on its 30-round magazine (magpul-pmag-30-gen-m3.side_panel_depth): none of this part's own shows in profile in any view on file, and a line seen face on doesn't say whether it is a groove or a ridge.","The round-count window is a mesh of its own since 2026-10-06 (the colours): a pane as thick as the relief, in the pocket cut for it under the recess's floor, its faces a few thousandths inside the body's so that none lies in one of them. The body's own mesh is as it was (51.6435 cubic inches, the same box).","Not drawn: the dust cover (a separate slip-on cap over the feed lips, on the magazine in no photo on file), the follower and any round, the window's numerals and what shows through it, the lever's thickness, its thumb pad and the channel it lies in, the clips' latches and screwdriver slots, the tower's side ribs, guide notches and markings, the body's fine texture."],"ledger":["magpul-pmag-d-60.overall_height","magpul-pmag-d-60.stated_width","magpul-pmag-d-60.drum_depth","magpul-pmag-d-60.drum_height","magpul-pmag-d-60.front_to_back","magpul-pmag-d-60.tower_width","magpul-pmag-d-60.tower_lean","magpul-pmag-d-60.catch_notch_top","magpul-pmag-d-60.catch_notch_lower_edge","magpul-pmag-d-60.spine_ahead_of_rear","magpul-pmag-d-60.spine_width","magpul-pmag-d-60.lips_slot_width","magpul-pmag-d-60.lips_slot_depth","magpul-pmag-d-60.clip_half_angle","magpul-pmag-d-60.clip_inner_radius","magpul-pmag-d-60.seam_rear_x","magpul-pmag-d-60.seam_front_x","magpul-pmag-d-60.dot_square","magpul-pmag-d-60.dot_group_gap","magpul-pmag-d-60.front_hub_radius","magpul-pmag-d-60.front_hub_rim_radius","magpul-pmag-d-60.front_ring_radius","magpul-pmag-30-gen-m3.side_panel_depth","magpul-pmag-30-gen-m3.spine_ahead_of_stop","magpul-pmag-30-gen-m3.catch_notch_height","magpul-pmag-30-gen-m3.catch_notch_rear_x","magpul-pmag-30-gen-m3.catch_notch_front_x","std.ar15.magwell_length","std.ar15.magwell_box_length","std.ar15.mag_catch_slot_floor"]},"profiles":{"rear":{"plane":"zy","origin":"the middle of the drum's width, at its lowest point (the photo is square to the rear cover: the drum's own end view, the feed tower leaning away above it)","offset":{},"points":[[-2.052,1.959],[-2.027,1.74],[-1.959,1.453],[-1.877,1.234],[-1.778,1.04],[-1.815,0.884],[-1.859,0.753],[-1.852,0.653],[-1.746,0.515],[-1.543,0.312],[-1.425,0.212],[-1.381,0.194],[-1.187,0.225],[-1.05,0.262],[-1.031,0.275],[-1.006,0.275],[-0.856,0.187],[-0.625,0.094],[-0.575,0.087],[-0.556,0.075],[-0.456,0.05],[-0.281,0.019],[0,0],[0.156,0],[0.306,0.019],[0.612,0.087],[0.687,0.125],[0.856,0.187],[0.981,0.262],[1,0.262],[1.037,0.237],[1.062,0.237],[1.156,0.206],[1.218,0.2],[1.306,0.175],[1.35,0.175],[1.381,0.187],[1.531,0.306],[1.734,0.509],[1.821,0.622],[1.834,0.69],[1.828,0.747],[1.79,0.865],[1.771,0.965],[1.759,0.984],[1.759,1.015],[1.828,1.134],[1.884,1.259],[1.99,1.578],[2.034,1.815],[2.052,2.077],[2.034,2.327],[1.965,2.646],[1.865,2.902],[1.771,3.071],[1.852,3.383],[1.852,3.421],[1.821,3.483],[1.746,3.577],[1.543,3.78],[1.393,3.905],[1.343,3.917],[1.25,3.886],[1.15,3.867],[1.087,3.842],[1.006,3.83],[0.9,3.886],[0.872,3.914],[0.865,3.964],[0.84,4.014],[0.772,4.077],[0.772,4.089],[0.756,4.105],[0.712,4.13],[0.631,4.142],[0.594,4.161],[0.581,4.149],[0.556,4.18],[0.5,4.192],[0.44,4.227],[0.447,6.22],[0.44,6.226],[0.447,6.239],[0.434,6.495],[0.428,7.213],[0.369,7.323],[0.331,7.354],[0.281,7.379],[0.231,7.385],[0.222,7.376],[0.222,7.257],[0.203,7.226],[0.172,7.126],[0.125,7.091],[0.056,7.091],[0.041,7.107],[0.047,7.194],[0.034,7.232],[-0.016,7.301],[-0.1,7.348],[-0.194,7.341],[-0.216,7.363],[-0.209,7.369],[-0.219,7.385],[-0.244,7.391],[-0.325,7.348],[-0.372,7.301],[-0.397,7.263],[-0.422,7.188],[-0.428,6.007],[-0.472,5.976],[-0.465,5.764],[-0.428,5.657],[-0.434,5.651],[-0.428,5.532],[-0.434,5.489],[-0.428,5.483],[-0.434,5.476],[-0.434,4.233],[-0.45,4.217],[-0.531,4.192],[-0.587,4.161],[-0.6,4.167],[-0.612,4.155],[-0.644,4.155],[-0.731,4.124],[-0.781,4.067],[-0.834,4.033],[-0.859,3.977],[-0.89,3.946],[-0.903,3.908],[-0.925,3.886],[-1.006,3.842],[-1.043,3.836],[-1.325,3.917],[-1.368,3.917],[-1.4,3.905],[-1.562,3.767],[-1.721,3.608],[-1.834,3.471],[-1.852,3.427],[-1.852,3.383],[-1.771,3.083],[-1.89,2.852],[-2.002,2.515],[-2.046,2.24]],"features":{"window":[[[-0.187,3.921],[0.194,3.921],[0.194,2.79],[-0.187,2.79]]],"window_recess":[[[-0.281,3.983],[0.287,3.983],[0.287,2.733],[-0.281,2.733]]],"hub":[[[-0.687,2.702],[0.7,2.702],[0.7,1.309],[-0.687,1.309]]],"hub_button":[[[-0.187,2.202],[0.2,2.202],[0.2,1.809],[-0.187,1.809]]],"dot_matrix":[[[-0.662,1.134],[0.656,1.134],[0.656,0.665],[-0.662,0.665]]],"catch_block":[[[-0.469,5.995],[-0.419,5.995],[-0.419,5.701],[-0.469,5.701]]],"collar":[[[-0.431,4.539],[0.437,4.539],[0.437,4.489],[-0.431,4.489]]]},"scaleRefs":["magpul-pmag-d-60.overall_height","magpul-pmag-d-60.stated_width"],"inputs":{"magpul-pmag-d-60.overall_height":7.4,"magpul-pmag-d-60.stated_width":4.1},"tolerance":0.006,"photo":"references/magpul-pmag-d-60 9a2a10cb54cb (the studio photo of the D-60 from the rear, square to the rear cover (as hosted by Sportsman's Warehouse, 1200 px))","method":"luminance < 200, closing ×2, largest piece, holes filled; scale from magpul-pmag-d-60.overall_height = 7.4 in (y-extent 1183 px → 159.9 px/in) and magpul-pmag-d-60.stated_width = 4.1 in (x-extent 657 px → 160.2 px/in), which agree within 0.2%; mean 160.1 px/in; origin at x center, y min of the outline; Douglas-Peucker at 0.006 in with the extremes kept: 146 points (IoU 0.998 with the full outline); features through the same placement (window: the translucent round-count window in the rear cover: its bright rectangle; window_recess: the rounded recess the window sits in: its outer dark line; hub: the round depression at the middle of the rear cover, on the drum's axis: the box round its rim's dark ring (centre 611, 867.5; radius 111 px); hub_button: the small round boss at the hub's middle (radius 31 px); dot_matrix: the paint-pen dot matrix under the hub: the box round its sixty squares, five rows of four groups of three (counted on this photo enlarged 2.4 times and on the patent's FIG. 3); catch_block: the block that stands out of the feed tower's left side under the catch's window, in profile: its flat top (rows 228 to 232, the tower's edge at column 535 for 543 above it) and where its chamfer is back in the side (row 276); collar: the collar round the feed tower's foot, where the tower ends and the drum's roof begins: its upper edge (row 462) and the width of the step there) (tools/trace.py)","via":"harvest"},"drum":{"plane":"xy","origin":"the drum standing as the patent draws it, its two faces upright: its rearmost point (the stop under the well and the rear cover's face) and its lowest point","offset":{},"points":[[0,4.217],[0.006,4.208],[0,4.165],[0.089,4.069],[0.074,4.044],[0.08,4.035],[0.068,3.84],[0.034,3.807],[0.022,3.751],[0.028,3.736],[0.022,3.726],[0.028,3.711],[0.022,3.702],[0.028,3.686],[0.022,3.677],[0.028,3.662],[0.022,3.652],[0.028,3.637],[0.022,3.628],[0.028,3.612],[0.022,3.603],[0.028,3.587],[0.022,3.578],[0.028,3.563],[0.022,3.553],[0.028,3.538],[0.022,3.529],[0.028,3.513],[0.022,3.504],[0.028,3.489],[0.022,3.174],[0.028,3.165],[0.009,2.995],[0.012,2.881],[0,2.834],[0.006,2.825],[0,2.785],[0.028,2.751],[0.025,1.325],[0.037,1.254],[0.031,1.242],[0.043,1.109],[0.022,1.079],[0.028,1.069],[0.022,1.06],[0.028,1.045],[0.022,1.035],[0.028,1.02],[0.022,1.011],[0.028,0.995],[0.022,0.986],[0.028,0.971],[0.022,0.961],[0.028,0.946],[0.022,0.937],[0.028,0.921],[0.022,0.912],[0.028,0.896],[0.022,0.887],[0.028,0.872],[0.022,0.863],[0.028,0.847],[0.022,0.838],[0.028,0.822],[0.022,0.813],[0.028,0.798],[0.022,0.788],[0.028,0.773],[0.022,0.764],[0.028,0.748],[0.022,0.739],[0.028,0.724],[0.022,0.714],[0.028,0.699],[0.022,0.69],[0.028,0.674],[0.022,0.665],[0.028,0.65],[0.022,0.64],[0.028,0.625],[0.022,0.616],[0.028,0.6],[0.022,0.591],[0.025,0.335],[0.031,0.307],[0.096,0.245],[0.105,0.103],[0.159,0.031],[0.313,0.022],[0.329,0.028],[0.523,0.009],[0.56,0.015],[0.603,0.009],[0.613,0],[0.631,0.015],[0.721,0.028],[0.733,0.022],[0.832,0.037],[0.921,0.037],[0.967,0.049],[1.008,0.046],[1.239,0.077],[1.329,0.074],[1.353,0.089],[1.369,0.083],[1.511,0.102],[1.523,0.096],[1.609,0.105],[1.625,0.114],[1.649,0.099],[1.668,0.114],[1.733,0.123],[1.77,0.12],[2.004,0.151],[2.094,0.148],[2.143,0.164],[2.159,0.157],[2.254,0.173],[2.291,0.148],[2.322,0.179],[2.362,0.185],[2.402,0.182],[2.523,0.201],[2.588,0.201],[2.609,0.21],[2.674,0.207],[3.075,0.25],[3.109,0.265],[3.444,0.588],[3.459,0.622],[3.472,0.687],[3.466,0.699],[3.496,0.835],[3.49,0.844],[3.512,0.924],[3.512,0.971],[3.521,0.983],[3.515,1.02],[3.564,1.446],[3.564,2.662],[3.515,3.091],[3.521,3.304],[3.512,3.316],[3.512,3.359],[3.586,3.489],[3.58,3.649],[3.595,3.674],[3.58,3.695],[3.586,3.856],[3.53,3.958],[3.461,4.024],[3.427,4.033],[3.319,4.03],[3.279,4.04],[3.266,4.033],[3.128,4.095],[3.106,4.114],[3.094,4.111],[3.057,4.135],[2.856,4.141],[2.855,4.013],[2.801,3.959],[2.705,3.969],[2.651,4.029],[2.654,4.149],[2.648,4.155],[2.657,4.168],[2.629,4.214],[2.555,4.282],[2.56,4.32],[2.532,4.293],[2.501,4.32],[2.443,4.262],[2.43,4.262],[2.412,4.243],[2.396,4.259],[2.365,4.262],[2.31,4.256],[2.294,4.24],[2.279,4.256],[2.227,4.252],[2.211,4.237],[2.199,4.249],[2.156,4.252],[2.131,4.234],[2.112,4.249],[2.06,4.249],[2.044,4.237],[1.995,4.286],[1.946,4.237],[1.93,4.249],[1.921,4.243],[1.878,4.249],[1.862,4.234],[1.838,4.249],[1.822,4.243],[1.801,4.249],[1.779,4.234],[1.764,4.249],[1.745,4.243],[1.708,4.249],[1.696,4.237],[1.683,4.249],[1.674,4.243],[1.631,4.249],[1.612,4.234],[1.591,4.249],[1.575,4.243],[1.554,4.249],[1.535,4.231],[1.517,4.249],[1.498,4.243],[1.461,4.249],[1.452,4.24],[1.44,4.249],[1.427,4.243],[1.384,4.249],[1.362,4.231],[1.344,4.249],[1.329,4.243],[1.307,4.249],[1.285,4.234],[1.27,4.249],[1.251,4.243],[1.214,4.249],[1.202,4.237],[1.19,4.249],[1.18,4.243],[1.137,4.249],[1.116,4.231],[1.097,4.249],[1.082,4.243],[1.06,4.249],[1.038,4.237],[1.023,4.249],[1.004,4.243],[0.967,4.249],[0.955,4.237],[0.943,4.249],[0.934,4.243],[0.89,4.249],[0.875,4.234],[0.85,4.249],[0.835,4.243],[0.813,4.249],[0.795,4.231],[0.776,4.249],[0.758,4.243],[0.721,4.249],[0.708,4.237],[0.696,4.249],[0.687,4.243],[0.643,4.249],[0.622,4.231],[0.603,4.249],[0.588,4.243],[0.569,4.249],[0.523,4.246],[0.511,4.234],[0.498,4.243],[0.44,4.24],[0.427,4.228],[0.412,4.24],[0.375,4.231],[0.36,4.237],[0.344,4.222],[0.332,4.234],[0.316,4.234],[0.273,4.274],[0.275,4.254],[0.224,4.203],[0.177,4.2],[0.153,4.181],[0.096,4.245],[0.114,4.266],[0.102,4.285],[0.12,4.303],[0.111,4.313],[0.136,4.337],[0.13,4.347],[0.199,4.416],[0.25,4.377],[0.241,4.476],[0.218,4.487],[0.181,4.456],[0.162,4.459],[0.134,4.487],[0.116,4.468],[0.091,4.487],[0.063,4.459],[0.037,4.452],[0.009,4.282],[0.012,4.239]],"scaleRefs":["magpul-pmag-d-60.drum_height"],"inputs":{"magpul-pmag-d-60.drum_height":4.487},"tolerance":0.006,"photo":"references/magpul-pmag-d-60 0ee2ad041291 (US D765,813 S (Magpul, 'Drum magazine for a firearm'), FIG. 4 left side elevation, 300 dpi: the drum below the feed tower)","method":"luminance < 128, inside [640, 1378, 1870, 2860], closing ×14, largest piece, holes filled, inset 2 px (half the outline's stroke); scale from magpul-pmag-d-60.drum_height = 4.487 in (y-extent 1454 px → 324.0 px/in); origin at x min, y min of the outline; Douglas-Peucker at 0.006 in with the extremes kept: 293 points (IoU 0.998 with the full outline); checks: width 3.595 ± 0.046 (tools/trace.py)","via":"harvest","note":"The drum as the patent stands it; the part's frame has the feed tower upright, which turns this by tower_lean (the model's script)."},"front":{"plane":"zy","origin":"the middle of the drum's width, at its lowest point; seen from the front, mirrored so that z is to the rifle's right","offset":{},"points":[[-2.05,4.233],[-2.048,0],[0,0],[2.05,0.002],[2.048,4.235]],"features":{"lever_eye":[[[0.455,3.873],[-0.118,3.873],[-0.118,3.3],[0.455,3.3]]],"lever_hole":[[[0.371,3.788],[-0.034,3.788],[-0.034,3.384],[0.371,3.384]]],"lever_arm":[[[-0.051,3.822],[-0.219,3.832],[-0.387,3.822],[-0.556,3.795],[-0.724,3.748],[-0.893,3.67],[-1.044,3.586],[-0.893,3.613],[-0.724,3.654],[-0.556,3.681],[-0.387,3.687],[-0.219,3.681],[-0.067,3.637]]]},"scaleRefs":["magpul-pmag-d-60.stated_width"],"inputs":{"magpul-pmag-d-60.stated_width":4.1},"tolerance":0.006,"photo":"references/magpul-pmag-d-60 0fccf578c45f (US D765,813 S (Magpul, 'Drum magazine for a firearm'), FIG. 2 front elevation, 300 dpi: the drum below the feed tower)","method":"manual polygon (4 points picked on the photo); scale from magpul-pmag-d-60.stated_width = 4.1 in (x-extent 1217 px → 296.8 px/in); origin at x center, y min of the outline; Douglas-Peucker at 0.006 in with the extremes kept: 5 points (IoU 1.000 with the full outline); features through the same placement (lever_eye: the loading lever stowed across the top of the front cover: the round eye at its pivot end, the box round its outer circle (centre 1185, 1670; radius 85 px); lever_hole: the hole in the lever's eye (radius 60 px); lever_arm: the lever's arm, from the eye to its point: its upper edge and its lower, picked on the sheet enlarged 1.5 times (± 8 px)) (tools/trace.py)","via":"harvest","note":"Read for the loading lever (features). Its outline is a box, not the front cover's: the figure's own extent across the drum (which sets the scale and the middle) and down to its lowest point; the patent draws the drum's rim in broken lines in this view."}},"gaps":[{"what":"A straight side view of the product: the feed tower's own outline, where it stands on the drum and how far it leans (10 degrees by the patent's broken lines; 10 to 15 by eye on two photos of it in a rifle)","need":"A studio photo of the D-60 from its side, square on, or a photo of it seated in a lower with both receiver pins in frame (trace.py register)"},{"what":"How deep the reliefs are (the window's recess, the hub, the dot matrix, the front cover's circles, the seams) and which way the front cover's circles step","need":"A view of each cover edge on, or close obliques of both covers"},{"what":"The retaining clips' own shape, the roof round the tower's foot in plan and the lever's thickness","need":"The patent's top and bottom plans (FIG. 6, 7) traced with the drum's outline (on file; used so far for the drum's depth and its taper), and a close view of the front cover from the side"},{"what":"The dust cover's weight (Magpul's 20.5 oz is with it) and the magazine's weight without it","need":"A page or a scale reading that gives either"},{"what":"The catch notch's height under the lips, to better than the ledge's reading (1.10 in here, 1.07 on the 30-round GEN M3: one catch, one bolt)","need":"A straight view of the tower's left side"}]},"mas-defense-nero-12-62-handguard":{"id":"mas-defense-nero-12-62-handguard","name":"12.62\" NERO M-LOK FREE FLOAT","manufacturer":"MAS Defense","sku":"MAS00106380","url":"https://www.masdefense.com/MAS00106380-p/mas00106380.htm","category":"handguard","description":"MAS Defense's 12.62 in NERO M-LOK free-float handguard (\"Rifle Length\"): a monolithic top rail that \"sits directly against the upper receiver rail\", M-LOK slots at 3, 6 and 9 o'clock, a slim 1.25 in bore that \"will require a slim muzzle device\", a QD socket at the front and rear, clamped on its own steel barrel nut by two screws. Made in USA.","weight":"mas-defense-nero-12-62-handguard.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"mount":{"origin":[0,0,0],"note":"The receiver's front face on the bore axis, +x toward the muzzle."},"mlok":{"origin":["{.rear_x} + {.mlok_slot0_from_rear_face}",0,0],"note":"On the handguard's axis (the bore's: its side faces' M-LOK row is at the bore's level) at the rearmost M-LOK slot's centre (index 0), +x toward the muzzle; the faces are angles about this axis (M10)."},"top_rail":{"origin":["{.rear_x} + {.rail_slot0_from_rear_face}","{.rail_top_above_bore}",0],"note":"The rail's top at its rearmost slot's centre, +x toward the muzzle (picatinny: index = slot number). Its own rail: the receiver's is the receiver's."}},"interfaces":{"handguard_mount":{"type":"ar15.handguard_mount","role":"handguard","anchor":"mount","params":{"nut":"standard"},"flips":false,"note":"MAS: \"The rail, steel barrel nut and attaching screws brings the weight to 12.4oz\" (it is sold with its own nut) and \"The monolithic top rail of the handguard sits directly against the upper receiver rail\"; its nut's own page: \"This barrel nut will only fit our Nero handguards\", \"The barrel nut accepts a standard AR-15 armorers wrench\"; MAS's Stealth Gray builder set pairs it with \"MAS Defense 7075 T6 Forged A4 Upper Receiver\". No page names the thread: `standard` is the upper's barrel-nut thread its own nut is taken to take, as a handguard sold with its own nut for an AR-15 upper is."},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}","beyond_seam":true,"seam_behind":"receiver","seam_ahead":"handguard"},"flips":false},"mlok":{"type":"mlok","role":"slots","anchor":"mlok","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_slots}","interval":"={std.mlok.interval}","face_distance":"={.face_distance}","bore":"={.inside_diameter}","reach_inside":"={.reach_inside}"},"faces":{"right":{"angle":90,"note":"the rifle's right side (+z), 3 o'clock"},"bottom":{"angle":180,"note":"6 o'clock"},"left":{"angle":-90,"note":"9 o'clock"}},"flips":false,"note":"How far an accessory's nuts may reach inside depends on what runs under it (a barrel, a gas block), other parts: reach_inside has no figure, so that check reads as unmade."}},"materials":{"body":{"label":"Handguard","finish":"cerakote","recolorable":true,"color":"mas-defense-stealth-gray","options":{"stealth-gray":{"label":"Stealth Gray (Cerakote)","finish":"cerakote","color":"mas-defense-stealth-gray","sku":"MAS00106380","source":"https://www.masdefense.com/MAS00106380-p/mas00106380.htm"},"black":{"label":"Black","finish":"anodized","color":"placeholder-black","sku":"MAS00106312","source":"https://www.masdefense.com/MAS00106312-p/mas00106312.htm"},"fde":{"label":"(FDE) Flat Dark Earth","finish":"cerakote","color":"mas-defense-fde","sku":"MAS00106362","source":"https://www.masdefense.com/MAS00106362-p/mas00106362.htm"},"od-green":{"label":"OD Green (Cerakote)","finish":"cerakote","color":"mas-defense-od-green","sku":"MAS00106212-ODG","source":"https://www.masdefense.com/MAS00106212-ODG-p/mas00106212-odg.htm"}},"default":"stealth-gray","note":"MAS sells the 12.62 in NERO in four colours, each a page and a number of its own (its site search for nero, 2026-10-28); no Navy Blue at this length. Stealth Gray is Cerakote by MAS's words for that colour elsewhere (the 9.87 in's title \"STEALTH GRAY CERAKOTE\", the 15 in's Stealth Gray builder set \"individually cerakoted\"); this page names no finish. The OD Green page names Cerakote; the FDE and black pages name none (the FDE drawn as Cerakote, as at every other length; the black as sealed black anodize, unmatched). The logo isn't drawn. The colours are MAS's presets read on the 15 in's pictures, the same colour names; this length's own pictures in each colour are the same pose and read alike."},"hardware":{"label":"Clamp screws","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The two screws across the clamp's lug at its rear end: their round heads on the left, their ends on the right. Dark in the Stealth Gray builder set's pictures and in the black and coloured handguards' pictures alike, so the slot follows nothing. MAS doesn't say what they are made of; the colour is a placeholder."}},"components":{},"geometry":{"model":"mas-defense-nero-12-62-handguard.glb","components":{},"approximations":["Its section is the 15 in's (one extrusion: the rows of openings and slots stand at the same heights on all three lengths' pictures of one pose), run between its two end faces 12.84 in apart: side flats 1.60 in apart, upper faces up to a neck under the rail's head 0.40 below its top (as deep as the clamps on file need), lower faces at 45 degrees down to the bottom flat 0.85 below the bore (no picture from below or from the end is on file); the rail's head is MIL-STD-1913's (Figure 1).","Bored to the published 1.25 in through the clamp's ring at its rear end; ahead of it its walls are the 15 in's thickness (worked out from the 15 in's published weight).","31 rail slots, 5 M-LOK slots in each side row and 14 openings in each upper and lower face, counted on MAS's picture of this length from the front right and above; their places along it read on that picture through the 15 in's picture of the same pose (each row's offset): to about 0.05 in. The left side's and the bottom's rows aren't in any picture of this length: taken to be the right side's.","The front and rear QD sockets drawn as round holes 0.37 in across through the side flats at the bore's level; the cups inside aren't drawn.","The clamp's lug under its rear end and its two screws as the 15 in's (no level picture of this length shows them); the split, the steel barrel nut inside the rear end and the logos aren't drawn. Edges broken at 0.012 in.","Placed with its rear face against the receiver's shoulder, where the barrel-nut thread begins, as the 15 in's level pictures show that length."],"ledger":["mas-defense-nero-12-62-handguard.length","mas-defense-nero-12-62-handguard.width","mas-defense-nero-12-62-handguard.height","mas-defense-nero-12-62-handguard.inside_diameter","mas-defense-nero-12-62-handguard.rear_x","mas-defense-nero-12-62-handguard.rail_top_above_bore","mas-defense-nero-12-62-handguard.bottom_below_bore","mas-defense-nero-12-62-handguard.mlok_slot0_from_rear_face","mas-defense-nero-12-62-handguard.rail_slot0_from_rear_face"]},"profiles":{"top":{"plane":"xz","origin":"the rear face on the bore's line, +x toward the muzzle; the picture's up is the handguard's left (-z)","offset":{},"points":[[-0.475,-0.333],[-0.461,-0.387],[-0.388,-0.402],[-0.35,-0.776],[-0.304,-0.798],[1.783,-0.807],[1.836,-0.792],[1.973,-0.808],[2.089,-0.793],[3.34,-0.808],[3.393,-0.794],[4.707,-0.809],[4.76,-0.794],[6.58,-0.811],[6.633,-0.797],[6.706,-0.812],[6.76,-0.798],[7.694,-0.811],[7.747,-0.797],[7.82,-0.812],[8.073,-0.813],[8.127,-0.798],[9.314,-0.813],[9.367,-0.798],[9.44,-0.813],[9.693,-0.814],[9.747,-0.8],[10.934,-0.814],[10.987,-0.8],[11.25,-0.816],[11.367,-0.802],[11.999,-0.804],[12.072,-0.819],[12.126,-0.805],[12.238,-0.815],[12.267,-0.795],[12.265,-0.744],[12.341,-0.368],[12.361,-0.334],[12.42,-0.295],[12.432,-0.234],[12.434,0.209],[12.429,0.247],[12.371,0.335],[12.347,0.34],[12.318,0.384],[12.309,0.525],[12.26,0.662],[12.271,0.774],[12.249,0.791],[11.806,0.792],[11.753,0.778],[11.616,0.793],[11.3,0.794],[11.247,0.78],[9.174,0.798],[9.121,0.784],[9.048,0.799],[8.732,0.8],[8.678,0.786],[8.479,0.801],[8.362,0.787],[8.289,0.802],[8.172,0.788],[7.919,0.789],[7.846,0.803],[7.793,0.789],[4.708,0.811],[4.655,0.797],[4.519,0.812],[4.202,0.813],[4.149,0.799],[3.833,0.8],[3.76,0.815],[3.643,0.801],[0.179,0.825],[0.126,0.81],[-0.327,0.827],[-0.349,0.78],[-0.335,0.664],[-0.374,0.532],[-0.377,0.457],[-0.421,0.428],[-0.445,0.433],[-0.472,0.363]],"scaleRefs":["mas-defense-nero-12-62-handguard.rear_x","mas-defense-nero-12-62-handguard.length"],"inputs":{"mas-defense-nero-12-62-handguard.length":12.84,"mas-defense-nero-12-62-handguard.rear_x":-0.445},"tolerance":0.01,"photo":"references/mas-defense-nero-12-62-handguard b602e7d5e531 (MAS's render of this length in FDE from above, beside its nut (its ends on the rail's centre line))","method":"luminance < 170, largest piece, holes filled; frame from the reviewed holes rear, front (57.0 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.01 in with the extremes kept: 85 points (IoU 0.995 with the full outline); checks: height 1.645 ± 0.053 in vs mas-defense-nero-12-62-handguard.width 1.6 ± 0.04 (provisional): agrees (tools/trace.py)","via":"harvest","note":"From above: the rail's top and both upper faces with their openings (filled); its ends where the silhouette's ends cross its centre line, set to the ledger's length."}},"gaps":[{"what":"A level side picture of this length (its places along it are read through a picture taken from the front right and above)","need":"MAS's picture of this length on an upper seen from the side, or a seller's"},{"what":"Its length: the title says 12.62 in, its pictures 12.84","need":"A published overall length with its ends named, or a level side picture"},{"what":"The left side's and the bottom's rows of M-LOK slots","need":"A picture from below or from the left"},{"what":"Its section from the end, and the walls inside","need":"A picture down its length or of its end face"},{"what":"The room inside its faces before what runs under it (reach_inside)","need":"The barrel's and the gas block's sizes under the slots: the build's"},{"what":"Which barrel-nut thread its steel nut takes","need":"A MAS sentence naming the thread"}]},"mas-defense-nero-15-handguard":{"id":"mas-defense-nero-15-handguard","name":"15\" NERO M-LOK FREE FLOAT","manufacturer":"MAS Defense","sku":"MAS00106384","url":"https://www.masdefense.com/MAS00106384-p/mas00106384.htm","category":"handguard","description":"MAS Defense's 15 in NERO M-LOK free-float handguard (\"Extended Rifle Length\"): a monolithic top rail that \"sits directly against the upper receiver rail\", M-LOK slots at 3, 6 and 9 o'clock, a slim 1.25 in bore that \"will require a slim muzzle device\", QD sockets at the front and rear, clamped on its own steel barrel nut by two screws. Made in USA.","weight":"mas-defense-nero-15-handguard.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"mount":{"origin":[0,0,0],"note":"The receiver's front face on the bore axis, +x toward the muzzle."},"mlok":{"origin":["{.rear_x} + {.mlok_slot0_from_rear_face}",0,0],"note":"On the handguard's axis (the bore's: its side faces' M-LOK row is at the bore's level) at the rearmost M-LOK slot's centre (index 0), +x toward the muzzle; the faces are angles about this axis (M10)."},"top_rail":{"origin":["{.rear_x} + {.rail_slot0_from_rear_face}","{.rail_top_above_bore}",0],"note":"The rail's top at its rearmost slot's centre, +x toward the muzzle (picatinny: index = slot number). Its own rail: the receiver's is the receiver's."}},"interfaces":{"handguard_mount":{"type":"ar15.handguard_mount","role":"handguard","anchor":"mount","params":{"nut":"standard"},"flips":false,"note":"MAS: \"The rail, steel barrel nut and attaching screws brings the weight to 13.4oz\" (it is sold with its own nut) and \"The monolithic top rail of the handguard sits directly against the upper receiver rail\"; its nut's own page: \"This barrel nut will only fit our Nero handguards\", \"The barrel nut accepts a standard AR-15 armorers wrench\"; MAS's Stealth Gray builder set pairs it with \"MAS Defense 7075 T6 Forged A4 Upper Receiver\". No page names the thread: `standard` is the upper's barrel-nut thread its own nut is taken to take, as a handguard sold with its own nut for an AR-15 upper is."},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}","beyond_seam":true,"seam_behind":"receiver","seam_ahead":"handguard"},"flips":false},"mlok":{"type":"mlok","role":"slots","anchor":"mlok","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_slots}","interval":"={std.mlok.interval}","face_distance":"={.face_distance}","bore":"={.inside_diameter}","reach_inside":"={.reach_inside}"},"faces":{"right":{"angle":90,"note":"the rifle's right side (+z), 3 o'clock"},"bottom":{"angle":180,"note":"6 o'clock"},"left":{"angle":-90,"note":"9 o'clock"}},"flips":false,"note":"How far an accessory's nuts may reach inside depends on what runs under it (a barrel, a gas block), other parts: reach_inside has no figure, so that check reads as unmade."}},"materials":{"body":{"label":"Handguard","finish":"cerakote","recolorable":true,"color":"mas-defense-stealth-gray","options":{"stealth-gray":{"label":"Stealth Gray (Cerakote)","finish":"cerakote","color":"mas-defense-stealth-gray","sku":"MAS00106384","source":"https://www.masdefense.com/MAS00106384-p/mas00106384.htm"},"black":{"label":"Black","finish":"anodized","color":"placeholder-black","sku":"MAS00106314","source":"https://www.masdefense.com/MAS00106314-p/mas00106314.htm"},"fde":{"label":"(FDE) Flat Dark Earth","finish":"cerakote","color":"mas-defense-fde","sku":"MAS00106364","source":"https://www.masdefense.com/MAS00106364-p/mas00106364.htm"},"navy-blue":{"label":"Navy Blue (Cerakote)","finish":"cerakote","color":"mas-defense-navy-blue","sku":"MAS00106214-BLU","source":"https://www.masdefense.com/MAS00106214-BLU-p/mas00106214-blu.htm"},"od-green":{"label":"OD Green (Cerakote, sold as a blem)","finish":"cerakote","color":"mas-defense-od-green","sku":"MAS00106214-ODGB","source":"https://www.masdefense.com/MAS00106214-ODG-p/mas00106214-odgb.htm"}},"default":"stealth-gray","note":"MAS sells the 15 in NERO in five colours, each a page and a number of its own (its site search for nero, 2026-10-28). Stealth Gray is Cerakote: MAS's builder set with this handguard is \"MAS DEFENSE CERAKOTE AR-15 STEALTH GRAY BUILDER SET\" (\"These kits are individually cerakoted\"), and the 9.87 in's title says \"STEALTH GRAY CERAKOTE\"; the 15 in's own page names no finish. \"Cerakoted Navy Blue\" and \"Cerakoted OD Green\" are those pages' words; the OD Green is sold only as a blem item (\"Parts may have minor cosmetic blemishes in the coating\"). The FDE page names no finish: drawn as Cerakote, as its weights are the Cerakoted ones' (10.2 and 14 oz, where the black and gray pages say 10 and 13.4). The black's page names no finish: drawn as sealed black anodize, unmatched. The logo (engraved, bare metal in every colour) isn't drawn. Every colour's picture is one pose, MAS's; the colours are read off them."},"hardware":{"label":"Clamp screws","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The two screws across the clamp's lug at its rear end: their round heads on the left, their ends on the right. Dark in the Stealth Gray builder set's pictures and in the black and coloured handguards' pictures alike, so the slot follows nothing. MAS doesn't say what they are made of; the colour is a placeholder."}},"components":{},"geometry":{"model":"mas-defense-nero-15-handguard.glb","components":{},"approximations":["Its section run between its two end faces, 15.12 in apart: side flats 1.60 in apart (the picture from above, against its rail's width) from 0.40 below the bore to 0.62 above it, faces from there up to a neck under the rail's head, 0.40 below its top (an assumption: as deep as the clamps on file need), the neck straight up to the rail's underside 0.24 below its top, and lower faces down to a bottom flat 0.85 below the bore, taken at 45 degrees (no picture from below is on file); the rail's head is MIL-STD-1913's (Figure 1). The bore's level is taken as its side faces' M-LOK row's.","Bored to the published 1.25 in, round; above the bore it is drawn hollow up to the rail's underside, its walls there as thick as the side flats' at the bore (no picture into it is on file; the pictures from above see through both rows of openings).","37 rail slots, 7 M-LOK slots in each side face's row and 18 openings in each upper and each lower face, each counted and placed on the builder set's two side pictures; the slots at the standard's size and pitch, the openings as parallelograms of the size and lean they show from the side. The bottom's row of M-LOK slots isn't in any picture: taken to be the side rows' seven at their places.","The front and rear QD sockets drawn as round holes 0.37 in across through the side flats at the bore's level; the cups inside them aren't drawn.","The clamp's lug under its rear end from the side pictures (its flat bottom, its sloped front), as wide as the bottom flat; its two screws as plain cylinders standing a hair proud, heads on the left and ends on the right. The split the screws close and the steel barrel nut inside the rear end aren't drawn.","The front end square at the rail's front end (the side pictures show its face's lower part a bevel's width further on, at three pixels); the logos aren't drawn. Edges broken at 0.012 in.","Placed with its rear face against the receiver's shoulder, where the barrel-nut thread begins (0.445 in behind the thread's end), as the builder set's side pictures show it."],"ledger":["mas-defense-nero-15-handguard.length","mas-defense-nero-15-handguard.width","mas-defense-nero-15-handguard.height","mas-defense-nero-15-handguard.inside_diameter","mas-defense-nero-15-handguard.rear_x","mas-defense-nero-15-handguard.rail_top_above_bore","mas-defense-nero-15-handguard.bottom_below_bore","mas-defense-nero-15-handguard.mlok_slot0_from_rear_face","mas-defense-nero-15-handguard.rail_slot0_from_rear_face"]},"profiles":{"side":{"plane":"xy","origin":"the photo's frame","offset":{},"points":[[-0.447,1.173],[-0.447,-1.043],[-0.432,-1.058],[-0.373,-0.999],[-0.284,-1.088],[0.721,-1.088],[0.809,-1.029],[0.839,-1.029],[1.016,-0.851],[3.616,-0.851],[3.646,-0.822],[3.823,-0.822],[3.853,-0.851],[4,-0.851],[4.03,-0.822],[4.06,-0.851],[4.887,-0.851],[4.916,-0.822],[4.946,-0.851],[5.271,-0.851],[5.301,-0.822],[5.33,-0.851],[5.36,-0.851],[5.389,-0.822],[6.246,-0.822],[6.276,-0.851],[6.305,-0.822],[14.254,-0.822],[14.283,-0.851],[14.638,-0.851],[14.653,-0.836],[14.653,-0.718],[14.682,-0.689],[14.682,-0.63],[14.712,-0.6],[14.712,-0.511],[14.741,-0.482],[14.741,-0.364],[14.771,-0.334],[14.771,0.198],[14.801,0.227],[14.771,0.257],[14.801,0.286],[14.801,0.316],[14.741,0.375],[14.741,0.552],[14.712,0.582],[14.712,0.67],[14.682,0.7],[14.682,1.232],[14.668,1.247],[14.136,1.247],[14.121,1.232],[14.121,1.143],[14.077,1.128],[14.062,1.143],[14.062,1.202],[14.017,1.247],[13.752,1.247],[13.737,1.232],[13.737,1.173],[13.692,1.128],[13.663,1.128],[13.648,1.143],[13.648,1.232],[13.633,1.247],[13.367,1.247],[13.323,1.202],[13.323,1.143],[13.279,1.128],[13.234,1.173],[13.234,1.232],[13.22,1.247],[12.954,1.247],[12.939,1.232],[12.939,1.143],[12.924,1.128],[12.865,1.128],[12.85,1.143],[12.85,1.232],[12.836,1.247],[12.57,1.247],[12.555,1.232],[12.555,1.173],[12.511,1.128],[12.481,1.128],[12.437,1.173],[12.437,1.232],[12.422,1.247],[12.185,1.247],[12.141,1.202],[12.141,1.143],[12.126,1.128],[12.067,1.128],[12.052,1.143],[12.052,1.202],[12.008,1.247],[11.772,1.247],[11.757,1.232],[11.757,1.143],[11.742,1.128],[11.654,1.128],[11.639,1.143],[11.639,1.232],[11.624,1.247],[11.388,1.247],[11.373,1.232],[11.373,1.173],[11.343,1.143],[11.329,1.128],[11.269,1.128],[11.225,1.173],[11.225,1.232],[11.21,1.247],[11.004,1.247],[10.959,1.202],[10.959,1.143],[10.944,1.128],[10.856,1.128],[10.841,1.143],[10.841,1.232],[10.826,1.247],[10.619,1.247],[10.575,1.202],[10.575,1.143],[10.531,1.099],[10.501,1.128],[10.442,1.128],[10.427,1.143],[10.427,1.232],[10.413,1.247],[10.206,1.247],[10.191,1.232],[10.191,1.143],[10.147,1.099],[10.117,1.128],[10.058,1.128],[10.043,1.143],[10.043,1.202],[9.999,1.247],[9.822,1.247],[9.777,1.202],[9.777,1.114],[9.762,1.099],[9.674,1.099],[9.629,1.143],[9.629,1.232],[9.615,1.247],[9.437,1.247],[9.393,1.202],[9.393,1.143],[9.349,1.099],[9.26,1.099],[9.245,1.114],[9.245,1.202],[9.201,1.247],[9.171,1.247],[9.142,1.217],[9.024,1.217],[9.009,1.202],[9.009,1.143],[8.965,1.099],[8.876,1.099],[8.832,1.143],[8.832,1.232],[8.787,1.247],[8.758,1.217],[8.64,1.217],[8.595,1.173],[8.595,1.114],[8.581,1.099],[8.462,1.099],[8.448,1.114],[8.448,1.202],[8.433,1.217],[8.226,1.217],[8.211,1.202],[8.211,1.114],[8.196,1.099],[8.078,1.099],[8.034,1.143],[8.034,1.202],[8.019,1.217],[7.842,1.217],[7.827,1.202],[7.827,1.114],[7.812,1.099],[7.665,1.099],[7.65,1.114],[7.65,1.202],[7.635,1.217],[7.458,1.217],[7.443,1.202],[7.443,1.143],[7.399,1.099],[7.251,1.099],[7.236,1.114],[7.236,1.202],[7.221,1.217],[7.074,1.217],[7.029,1.173],[7.059,1.143],[7.014,1.099],[6.867,1.099],[6.822,1.143],[6.852,1.173],[6.837,1.217],[6.66,1.217],[6.645,1.202],[6.645,1.114],[6.63,1.099],[6.453,1.099],[6.438,1.114],[6.438,1.202],[6.423,1.217],[6.276,1.217],[6.261,1.202],[6.261,1.114],[6.246,1.099],[6.069,1.099],[6.054,1.114],[6.054,1.202],[6.039,1.217],[5.892,1.217],[5.877,1.202],[5.877,1.114],[5.862,1.099],[5.655,1.099],[5.64,1.114],[5.64,1.202],[5.626,1.217],[5.478,1.217],[5.463,1.173],[5.493,1.143],[5.448,1.099],[5.271,1.099],[5.256,1.114],[5.256,1.202],[5.242,1.217],[5.094,1.217],[5.079,1.202],[5.079,1.114],[5.064,1.099],[4.887,1.099],[4.872,1.114],[4.872,1.202],[4.857,1.217],[4.71,1.217],[4.665,1.173],[4.695,1.143],[4.651,1.099],[4.503,1.099],[4.488,1.114],[4.488,1.202],[4.473,1.217],[4.296,1.217],[4.281,1.202],[4.281,1.114],[4.266,1.099],[4.119,1.099],[4.104,1.114],[4.104,1.173],[4.06,1.217],[3.912,1.217],[3.897,1.202],[3.897,1.114],[3.882,1.099],[3.735,1.099],[3.72,1.114],[3.72,1.173],[3.675,1.217],[3.498,1.217],[3.483,1.202],[3.483,1.114],[3.469,1.099],[3.321,1.099],[3.306,1.114],[3.306,1.202],[3.291,1.217],[3.114,1.217],[3.099,1.202],[3.099,1.114],[3.084,1.099],[2.937,1.099],[2.922,1.114],[2.922,1.202],[2.907,1.217],[2.73,1.217],[2.715,1.202],[2.715,1.143],[2.671,1.099],[2.553,1.099],[2.538,1.114],[2.538,1.202],[2.523,1.217],[2.346,1.217],[2.301,1.173],[2.301,1.114],[2.287,1.099],[2.228,1.099],[2.198,1.069],[2.154,1.114],[2.154,1.202],[2.139,1.217],[1.932,1.217],[1.917,1.202],[1.917,1.114],[1.902,1.099],[1.784,1.099],[1.77,1.114],[1.77,1.173],[1.725,1.217],[1.548,1.217],[1.533,1.202],[1.533,1.114],[1.489,1.069],[1.43,1.069],[1.385,1.114],[1.385,1.173],[1.341,1.217],[1.312,1.217],[1.282,1.188],[1.193,1.188],[1.164,1.217],[1.119,1.173],[1.119,1.114],[1.075,1.069],[1.046,1.069],[1.001,1.114],[1.001,1.173],[0.957,1.217],[0.927,1.217],[0.898,1.188],[0.809,1.188],[0.78,1.217],[0.735,1.173],[0.735,1.114],[0.691,1.069],[0.661,1.069],[0.617,1.114],[0.617,1.173],[0.573,1.217],[0.543,1.217],[0.514,1.188],[0.366,1.188],[0.351,1.173],[0.351,1.114],[0.307,1.069],[0.248,1.069],[0.233,1.084],[0.233,1.173],[0.189,1.217],[0.159,1.217],[0.13,1.188],[-0.018,1.188],[-0.062,1.143],[-0.062,1.084],[-0.077,1.069],[-0.136,1.069],[-0.151,1.084],[-0.151,1.173],[-0.166,1.188],[-0.432,1.188]],"scaleRefs":["mas-defense-nero-15-handguard.rear_x","mas-defense-nero-15-handguard.rail_slot0_from_rear_face","mas-defense-nero-15-handguard.rail_top_above_bore","std.picatinny.slot_depth","std.picatinny.slot_pitch"],"inputs":{"mas-defense-nero-15-handguard.rail_slot0_from_rear_face":0.35,"mas-defense-nero-15-handguard.rail_top_above_bore":1.22,"mas-defense-nero-15-handguard.rear_x":-0.445,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394},"tolerance":0.01,"photo":"references/mas-defense-nero-15-handguard 6bf562718703 (the Stealth Gray builder set's right side seen level: the handguard on MAS's upper (MDCK-AR15-SUL-NM15-STGRY-2))","method":"luminance < 160, inside [272, 205, 792, 302], largest piece, holes filled; frame from the reviewed holes slot0, slot36 (33.8 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.01 in with the extremes kept: 363 points (IoU 1.000 with the full outline); checks: x_max in y [1.0, 1.3] 14.682 ± 0.064; y_max 1.247 ± 0.044 in vs mas-defense-nero-15-handguard.rail_top_above_bore 1.22 ± 0.04 (corroborated): agrees; −y_min in x [3, 14] 0.851 ± 0.044 in vs mas-defense-nero-15-handguard.bottom_below_bore 0.85 ± 0.04 (corroborated): agrees; −y_min 1.088 ± 0.044 in vs mas-defense-nero-15-handguard.lug_bottom_below_bore 1.08 ± 0.03 (provisional): agrees (tools/trace.py)","via":"harvest","note":"Its rear end is the region's edge at the seam with the receiver (its rear face, column 272); the openings and slots are inside the outline (its holes filled), and the rail's slots are its teeth: the model cuts both at the standard's size. Below the bottom flat at the rear hangs the clamp's lug."}},"gaps":[{"what":"Its section from the end: the lower faces' angle, the bottom flat's width, the walls inside","need":"A picture down its length or of its end face (none on file: MAS's pictures are from above and from the sides)"},{"what":"The bottom's row of M-LOK slots: how many and where","need":"A picture from below (MAS says only \"3, 6 and 9 o'clock\")"},{"what":"The room inside its faces before what runs under it (reach_inside: what an M-LOK accessory's nuts may take)","need":"The barrel's and the gas block's sizes under the slots: the build's, once those parts state them"},{"what":"Which barrel-nut thread its steel nut takes","need":"A MAS sentence naming the thread (its pages say only that the nut \"will only fit our Nero handguards\")"},{"what":"Its barrel nut's own shape (drawn as nothing: it is inside the rear end)","need":"MAS's NERO barrel nut page's picture at a size to read (MAS00106018: 300 px)"}]},"mas-defense-nero-9-87-handguard":{"id":"mas-defense-nero-9-87-handguard","name":"9.87\" NERO M-LOK FREE FLOAT","manufacturer":"MAS Defense","sku":"MAS00106378","url":"https://www.masdefense.com/MAS00106375-p/mas00106378.htm","category":"handguard","description":"MAS Defense's 9.87 in NERO M-LOK free-float handguard (\"Specter Length\"): a monolithic top rail that \"sits directly against the upper receiver rail\", M-LOK slots at 3, 6 and 9 o'clock, a slim 1.25 in bore that \"will require a slim muzzle device\", a QD socket at the rear, clamped on its own steel barrel nut by two screws. Made in USA.","weight":"mas-defense-nero-9-87-handguard.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"mount":{"origin":[0,0,0],"note":"The receiver's front face on the bore axis, +x toward the muzzle."},"mlok":{"origin":["{.rear_x} + {.mlok_slot0_from_rear_face}",0,0],"note":"On the handguard's axis (the bore's: its side faces' M-LOK row is at the bore's level) at the rearmost M-LOK slot's centre (index 0), +x toward the muzzle; the faces are angles about this axis (M10)."},"top_rail":{"origin":["{.rear_x} + {.rail_slot0_from_rear_face}","{.rail_top_above_bore}",0],"note":"The rail's top at its rearmost slot's centre, +x toward the muzzle (picatinny: index = slot number). Its own rail: the receiver's is the receiver's."}},"interfaces":{"handguard_mount":{"type":"ar15.handguard_mount","role":"handguard","anchor":"mount","params":{"nut":"standard"},"flips":false,"note":"MAS: \"The rail, steel barrel nut and attaching screws brings the weight to 10.6oz\" (it is sold with its own nut) and \"The monolithic top rail of the handguard sits directly against the upper receiver rail\"; its nut's own page: \"This barrel nut will only fit our Nero handguards\", \"The barrel nut accepts a standard AR-15 armorers wrench\"; MAS's Stealth Gray builder set pairs it with \"MAS Defense 7075 T6 Forged A4 Upper Receiver\". No page names the thread: `standard` is the upper's barrel-nut thread its own nut is taken to take, as a handguard sold with its own nut for an AR-15 upper is."},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}","beyond_seam":true,"seam_behind":"receiver","seam_ahead":"handguard"},"flips":false},"mlok":{"type":"mlok","role":"slots","anchor":"mlok","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_slots}","interval":"={std.mlok.interval}","face_distance":"={.face_distance}","bore":"={.inside_diameter}","reach_inside":"={.reach_inside}"},"faces":{"right":{"angle":90,"note":"the rifle's right side (+z), 3 o'clock"},"bottom":{"angle":180,"note":"6 o'clock"},"left":{"angle":-90,"note":"9 o'clock"}},"flips":false,"note":"How far an accessory's nuts may reach inside depends on what runs under it (a barrel, a gas block), other parts: reach_inside has no figure, so that check reads as unmade."}},"materials":{"body":{"label":"Handguard","finish":"cerakote","recolorable":true,"color":"mas-defense-stealth-gray","options":{"stealth-gray":{"label":"Stealth Gray (Cerakote)","finish":"cerakote","color":"mas-defense-stealth-gray","sku":"MAS00106378","source":"https://www.masdefense.com/MAS00106375-p/mas00106378.htm"},"black":{"label":"Black","finish":"anodized","color":"placeholder-black","sku":"MAS00106308","source":"https://www.masdefense.com/MAS00106308-p/mas00106308.htm"},"fde":{"label":"(FDE) Flat Dark Earth","finish":"cerakote","color":"mas-defense-fde","sku":"MAS00106358","source":"https://www.masdefense.com/MAS00106358-p/mas00106358.htm"},"navy-blue":{"label":"Navy Blue (Cerakote)","finish":"cerakote","color":"mas-defense-navy-blue","sku":"MAS00106208-BLU","source":"https://www.masdefense.com/MAS00106208-BLU-p/mas00106208-blu.htm"},"od-green":{"label":"OD Green (Cerakote)","finish":"cerakote","color":"mas-defense-od-green","sku":"MAS00106208-ODG","source":"https://www.masdefense.com/MAS00106208-ODG-p/mas00106208-odg.htm"}},"default":"stealth-gray","note":"MAS sells the 9.87 in NERO in five colours, each a page and a number of its own (its site search for nero, 2026-10-28). Its Stealth Gray page's title says \"STEALTH GRAY CERAKOTE\"; the Navy Blue and OD Green pages name Cerakote; the FDE page's description names none (a buyer on it: \"the FDE cerakote was flawless\"); the black page names none (drawn as sealed black anodize, unmatched). The logo isn't drawn. The colours are MAS's presets read on the 15 in's pictures, the same colour names; this length's own pictures in each colour are the same pose and read alike."},"hardware":{"label":"Clamp screws","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The two screws across the clamp's lug at its rear end: their round heads on the left, their ends on the right. Dark in the Stealth Gray builder set's pictures and in the black and coloured handguards' pictures alike, so the slot follows nothing. MAS doesn't say what they are made of; the colour is a placeholder."}},"components":{},"geometry":{"model":"mas-defense-nero-9-87-handguard.glb","components":{},"approximations":["Its section is the 15 in's (one extrusion: the rows of openings and slots stand at the same heights on all three lengths' pictures of one pose), run between its two end faces 10.01 in apart: side flats 1.60 in apart, upper faces up to a neck under the rail's head 0.40 below its top (as deep as the clamps on file need), lower faces at 45 degrees down to the bottom flat 0.85 below the bore (no picture from below or from the end is on file); the rail's head is MIL-STD-1913's (Figure 1).","Bored to the published 1.25 in through the clamp's ring at its rear end; ahead of it its walls are the 15 in's thickness (worked out from the 15 in's published weight).","24 rail slots, 4 M-LOK slots in each side row and 10 openings in each upper and lower face, counted on MAS's picture of this length from the front right and above; their places along it read on that picture through the 15 in's picture of the same pose (each row's offset): to about 0.05 in. The left side's and the bottom's rows aren't in any picture of this length: taken to be the right side's.","The rear QD socket drawn as round holes 0.37 in across through the side flats at the bore's level; the cups inside aren't drawn. MAS pages for this length in FDE, OD Green and Navy Blue say \"at the front and rear positions\"; its Stealth Gray and black pages say \"at the rear position\", and every picture of it has one socket, at the rear.","The clamp's lug under its rear end and its two screws as the 15 in's (no level picture of this length shows them); the split, the steel barrel nut inside the rear end and the logos aren't drawn. Edges broken at 0.012 in.","Placed with its rear face against the receiver's shoulder, where the barrel-nut thread begins, as the 15 in's level pictures show that length."],"ledger":["mas-defense-nero-9-87-handguard.length","mas-defense-nero-9-87-handguard.width","mas-defense-nero-9-87-handguard.height","mas-defense-nero-9-87-handguard.inside_diameter","mas-defense-nero-9-87-handguard.rear_x","mas-defense-nero-9-87-handguard.rail_top_above_bore","mas-defense-nero-9-87-handguard.bottom_below_bore","mas-defense-nero-9-87-handguard.mlok_slot0_from_rear_face","mas-defense-nero-9-87-handguard.rail_slot0_from_rear_face"]},"profiles":{"top":{"plane":"xz","origin":"the rear face on the bore's line, +x toward the muzzle; the picture's up is the handguard's left (-z)","offset":{},"points":[[-0.474,-0.06],[-0.465,-0.348],[-0.446,-0.377],[-0.45,-0.401],[-0.363,-0.405],[-0.344,-0.433],[-0.328,-0.549],[-0.308,-0.577],[-0.307,-0.64],[-0.288,-0.669],[-0.286,-0.794],[-0.264,-0.81],[-0.125,-0.799],[-0.052,-0.812],[0.073,-0.811],[0.125,-0.796],[0.198,-0.809],[0.251,-0.794],[0.535,-0.81],[1.175,-0.792],[1.247,-0.806],[1.512,-0.793],[1.584,-0.806],[1.637,-0.791],[1.709,-0.804],[2.162,-0.789],[2.234,-0.803],[2.686,-0.787],[2.759,-0.801],[3.611,-0.785],[3.683,-0.799],[3.948,-0.786],[4.02,-0.799],[4.073,-0.784],[4.145,-0.798],[4.41,-0.785],[4.482,-0.798],[4.809,-0.784],[4.882,-0.798],[4.934,-0.783],[5.007,-0.796],[5.334,-0.783],[5.406,-0.796],[5.459,-0.781],[5.531,-0.794],[5.584,-0.779],[5.657,-0.793],[5.921,-0.78],[5.994,-0.793],[6.046,-0.778],[6.119,-0.792],[6.446,-0.778],[6.518,-0.792],[6.908,-0.777],[6.98,-0.791],[7.433,-0.775],[7.505,-0.789],[7.62,-0.773],[7.693,-0.786],[8.882,-0.771],[8.954,-0.785],[9.093,-0.773],[9.166,-0.787],[9.416,-0.784],[9.43,-0.774],[9.442,-0.714],[9.432,-0.699],[9.457,-0.629],[9.502,-0.325],[9.573,-0.276],[9.594,-0.23],[9.582,-0.028],[9.598,0.256],[9.577,0.347],[9.48,0.428],[9.469,0.567],[9.429,0.687],[9.432,0.774],[9.413,0.802],[9.352,0.814],[9.3,0.799],[9.227,0.812],[8.501,0.798],[8.428,0.812],[8.313,0.796],[8.115,0.808],[8.063,0.793],[7.904,0.81],[7.851,0.795],[7.653,0.807],[7.601,0.791],[7.528,0.805],[7.264,0.792],[7.191,0.806],[6.614,0.789],[6.541,0.802],[6.277,0.789],[6.204,0.803],[5.016,0.788],[4.943,0.801],[4.303,0.783],[4.231,0.797],[4.029,0.785],[3.956,0.798],[3.504,0.783],[3.432,0.796],[3.379,0.781],[3.306,0.795],[2.854,0.779],[2.782,0.793],[2.517,0.78],[2.445,0.793],[2.392,0.778],[2.32,0.792],[1.068,0.776],[0.996,0.789],[0.081,0.773],[0.009,0.787],[-0.193,0.774],[-0.265,0.788],[-0.286,0.742],[-0.268,0.639],[-0.333,0.426],[-0.362,0.406],[-0.434,0.42],[-0.457,0.362],[-0.471,0.152],[-0.46,0.013]],"scaleRefs":["mas-defense-nero-9-87-handguard.rear_x","mas-defense-nero-9-87-handguard.length"],"inputs":{"mas-defense-nero-9-87-handguard.length":10.01,"mas-defense-nero-9-87-handguard.rear_x":-0.445},"tolerance":0.01,"photo":"references/mas-defense-nero-9-87-handguard e83bcb86bd83 (MAS's render of this length in FDE from above, beside its nut (its ends on the rail's centre line))","method":"luminance < 170, largest piece, holes filled; frame from the reviewed holes rear, front (57.6 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.01 in with the extremes kept: 128 points (IoU 0.995 with the full outline); checks: height 1.626 ± 0.052 in vs mas-defense-nero-9-87-handguard.width 1.6 ± 0.04 (provisional): agrees (tools/trace.py)","via":"harvest","note":"From above: the rail's top and both upper faces with their openings (filled); its ends where the silhouette's ends cross its centre line, set to the ledger's length."}},"gaps":[{"what":"A level side picture of this length (its places along it are read through a picture taken from the front right and above)","need":"MAS's picture of this length on an upper seen from the side, or a seller's"},{"what":"Its length: the title says 9.87 in, its pictures 10.01","need":"A published overall length with its ends named, or a level side picture"},{"what":"The left side's and the bottom's rows of M-LOK slots","need":"A picture from below or from the left"},{"what":"Its section from the end, and the walls inside","need":"A picture down its length or of its end face"},{"what":"The room inside its faces before what runs under it (reach_inside)","need":"The barrel's and the gas block's sizes under the slots: the build's"},{"what":"Which barrel-nut thread its steel nut takes","need":"A MAS sentence naming the thread"}]},"mft-battlelink-minimalist-stock":{"id":"mft-battlelink-minimalist-stock","name":"BATTLELINK Minimalist Milspec Stock","manufacturer":"Mission First Tactical","sku":"BMSMIL","url":"https://missionfirsttactical.com/BMSMIL","category":"stock","description":"Mission First Tactical's skeleton carbine stock: a housing round the tube with a ridge down each side, an L of struts to an angled rubber butt pad, sling slots through the web and the strut, an upright QD socket under the neck and a forked lever that draws the lock pin down. 5.8 oz, for mil-spec carbine receiver extensions. Its shape is read from the maker's two straight side photos and a seller's straight view into its mouth; no drawing or patent of it is on file.","weight":"mft-battlelink-minimalist-stock.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"butt":{"origin":[0,0,0],"note":"The butt's plane on the tube axis: the part frame's origin (the pad's rearmost point, at its heel: the butt is angled, its toe further forward). Overall length and length of pull end here."},"tube":{"origin":["{.butt_behind_pin_pos1}",0,0],"x":[-1,0,0],"note":"Stock frame: origin on the tube axis in the plane of the butt, +x forward. At position 1 this anchor sits at the takedown pin's X."}},"interfaces":{"tube":{"type":"receiver_extension","role":"stock","anchor":"tube","params":{"profile":"mil-spec"},"flips":false,"note":"Mission First Tactical's page: \"Mil Spec size 1.148 diameter receiver extensions (buffer tube)\"; Primary Arms: \"Note: fits Mil-Spec, 1.148\" diameter receiver extensions (buffer tubes) only. Not compatible with commercial-spec tubes.\" The commercial-tube stock is a product of its own (BMS, \"Commercial spec size 1.17 diameter\"), not a fitment of this one."}},"materials":{"body":{"label":"Stock body","finish":"polymer","recolorable":true,"color":"placeholder-polymer-black","sheen":"satin","options":{"black":{"label":"Black","finish":"polymer","color":"placeholder-polymer-black","sheen":"satin","sku":"BMSMIL","source":"https://missionfirsttactical.com/BMSMIL"},"sde":{"label":"Scorched Dark Earth","finish":"polymer","color":"mft-scorched-dark-earth","sheen":"satin","sku":"BMSMILSDE","source":"https://www.primaryarms.com/mission-first-tactical-battlelink-minimalist-stock-milspec-scorched-dark-earth"}},"default":"black","note":"The maker's page offers BMSMIL in two colours, \"Color: Black, Scorched Dark Earth\" (its description: \"NSN: 1005226366907 (Black) NSN: 1005226366908 (Scorched Dark Earth)\"), the housing, the frame and the lever in the colour. Its material in the maker's words (the 2013 release, as Officer.com carries it): \"Made from a specially developed, reinforced, super-tough polyamide from DuPont's Military Plastic Division\". The black is the catalog's placeholder polymer black. The earth one's own number is a seller's: Primary Arms' page for it writes \"MPN: BMSMILSDE\" (the maker's page sells both under BMSMIL); its colour is matched on the maker's two pictures of it (data/colors/mission-first-tactical.yaml). Sold too and not offered here: gray and foliage green, which an airsoft shop's page lists (RedWolf: \"Comes in different colours. Black, SDE, Gray, and FG.\") and the maker's page no longer does; no photo of either large enough to match is on file."},"buttpad":{"label":"Buttpad","finish":"rubber","recolorable":false,"color":"placeholder-polymer-black","note":"The maker: \"Angled non-slip rubberized buttpad\"; Wing Tactical: \"Material: Polymer body with rubber butt pad\". Black on the black stock and on the scorched dark earth one alike (the maker's BMSMIL-scorched_dark_earth pictures; Wing Tactical's photo of the two together)."},"qd":{"label":"QD socket","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The cup in the socket's mouth under the neck: dark and glossy from below on the black stock (BMSMIL_black_07) and on the earth one (BMSMIL-scorched_dark_earth-7). No page names its metal or its finish (Redcon1's table: \"Sling Mount Type QD Swivel Socket\"): drawn as dark steel, by its shine."},"hardware":{"label":"Lock pin, its spring and cross pin","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The lock pin with its foot in the bar's underside, the cross pin through it whose rounded ends the lever bears on, and the coil spring in its window: dark steel on both colours (the maker's pictures of each; Wing Tactical's of the earth one), the cross pin's ends and the spring's turns catching the light. No page names the steel or its finish. The lever's pivot is not of these: it is the earth colour on the earth stock, and is drawn as a boss of the body."}},"components":{"body":{"label":"Stock body and lever","material":"body"},"buttpad":{"label":"Buttpad","material":"buttpad"},"qd":{"label":"QD socket","material":"qd"},"hardware":{"label":"Lock pin, its spring and cross pin","material":"hardware"}},"geometry":{"model":"mft-battlelink-minimalist-stock.glb","components":{},"approximations":["Built piece by piece inside the maker's straight right-side outline (scaled by its 7.084 x 5.22 in, which fit it within 1.5%; the left side's outline agrees with it to 0.055 in). No view shows the butt, the top or the underside square, and no drawing or patent is on file, so each piece is as wide as one reading of it, not a hull of three views.","The housing is the section at its mouth (Wing Tactical's straight view into it: an arch over a ridge each side at the tube's height, 1.61 in across, leaning in to the neck round the indexing rail's channel) carried the stock's length. Behind the step in its side it is the fuller cheek part: under the ridge its side leans out and then stands upright, from 0.89 in below the top (where it first shows beside the mouth in that view) down to the ledge's foot. The ledge's four cells are cut where the side photo has them, as deep as the frame's panels are recessed (their own depth isn't read); the groove they lie in isn't drawn.","The published width, 1.752 in, is given to that rear part and to the butt pad's upper part round its end: no view shows the widest place square, the mouth is not it (1.61), and the rear part reads 1.69 ± 0.05 in where it begins, in the view into the mouth. Below the rear part's foot the pad tapers to the two widths read behind the strut in the same view, 1.42 in at 3.0 in below the top and 1.20 at the toe, each ± 0.08. Its ridges and grooves are the side outline's, carried straight across; the maker's mark on its heel isn't drawn.","The frame (the web behind the lever, the arc and the strut down to the toe) is 0.47 in wide at its flanges, the strut's front flange in the view into the mouth, and its four panels (the triangle behind the arc, the panel round the web's slot, the stadium round each of the strut's slots) are recessed each side to a web 0.25 in thick: one reading, at the web's slot in an oblique, ± 0.06, carried to all four. The thin rib beside the web's slot and the slots' own rims aren't drawn. The plate the pad sits on is as wide as the pad. Under the neck's front the socket's boss is a round column 0.63 in across (the view into the mouth and the view from below agree; the side photo's own reading of it is 0.58) and the foot ahead of it, with its triangle, a slab as wide. Behind the boss the bar along the block's foot and the strip under the lever are drawn at the frame's width (the boss stands proud of the bar in both views from below; the bar's own width isn't read), and the pocket between them (with the spring's window) is recessed each side by the panels' depth.","The lever is a fork inside its outline in the side view: a plate each side of the neck and the block, as far apart as the lock pin's cross pin is long (1.08 in: the plates' own span isn't read), and the paddle whole under the frame, its ribs the outline's.","The bore is the keyed opening the view into the mouth shows (a round top of 0.584 in radius over lower flats), with the indexing rail's channel cut at the rail's own width (0.49 in: the photo reads 0.477 ± 0.02) down to the floor the photo shows (0.885 in below the axis) and the tube's own 1.148 in cut clear, one section from the front back to where the tube's rear end reaches with the stock collapsed. The hole in the top over the lock pin is drawn round, 0.39 in.","The steel is drawn plain: the lock pin a rod of its foot's diameter from the bar's underside to the channel's floor (its upper end, which stands in the tube's hole, isn't drawn, so nothing of it is in the tube's place), its spring three turns of wire round it in the window (the turns the window shows; how long the spring is isn't read), its cross pin a rod across the stock. The lever's pivot is a boss of the body each side, a hair proud of the lever's plate. The QD socket is a cup as deep as its boss is tall (its depth and its anti-rotation stops aren't read).","Its weight as a check of its shape takes a polyamide's density on trust: no page gives the resin's (a nylon is about 1.14 g/cc, a glass-filled one up to 1.4: 0.66 to 0.81 oz to the cubic inch, the same range the catalog's other polymer stocks are held to).","Not drawn: the markings (BMSMIL on the right, the maker's mark on the left), the pad's mark, the ribs inside the frame's panels. Edges broken at 0.02 in.","Its seat on the tube is its own lock pin (4.83 in ahead of the butt in the maker's side photo) in the tube's front hole, ± 0.08 in, which leaves its front 0.13 in behind the castle nut when collapsed; Wing Tactical's oblique photo of it on a rifle agrees within 0.07 in, read as one hole out. No length of pull is published."],"ledger":["mft-battlelink-minimalist-stock.length","mft-battlelink-minimalist-stock.height","mft-battlelink-minimalist-stock.width","mft-battlelink-minimalist-stock.tube_axis_below_top","mft-battlelink-minimalist-stock.mouth_height","mft-battlelink-minimalist-stock.body_width","mft-battlelink-minimalist-stock.rear_width","mft-battlelink-minimalist-stock.rear_wall_top_below_top","mft-battlelink-minimalist-stock.neck_width","mft-battlelink-minimalist-stock.block_width","mft-battlelink-minimalist-stock.frame_width","mft-battlelink-minimalist-stock.web_thickness","mft-battlelink-minimalist-stock.pad_width_low","mft-battlelink-minimalist-stock.pad_width_toe","mft-battlelink-minimalist-stock.pad_width_low_below_top","mft-battlelink-minimalist-stock.rail_channel_floor_below_axis","mft-battlelink-minimalist-stock.top_hole_diameter","mft-battlelink-minimalist-stock.lock_pin_ahead_of_butt","mft-battlelink-minimalist-stock.lock_pin_diameter","mft-battlelink-minimalist-stock.cross_pin_length","mft-battlelink-minimalist-stock.cross_pin_diameter","mft-battlelink-minimalist-stock.pivot_pin_diameter","mft-battlelink-minimalist-stock.spring_wire_diameter","mft-battlelink-minimalist-stock.qd_bore_diameter","mft-battlelink-minimalist-stock.qd_rim_diameter","mft-battlelink-minimalist-stock.butt_behind_pin_pos1"]},"profiles":{"side":{"plane":"xy","origin":"rearmost point of the butt pad (x) and the housing's top edge (y); the photo shows the top level, so the tube axis is horizontal","offset":{"y":"tube_axis_below_top"},"points":[[0,-0.616],[0,-0.861],[0.032,-1.226],[0.048,-1.251],[0.085,-1.256],[0.115,-1.281],[0.129,-1.383],[0.125,-1.42],[0.06,-1.457],[0.074,-1.609],[0.09,-1.648],[0.141,-1.658],[0.162,-1.678],[0.171,-1.738],[0.171,-1.812],[0.106,-1.854],[0.125,-2.011],[0.141,-2.041],[0.208,-2.066],[0.222,-2.149],[0.222,-2.214],[0.162,-2.26],[0.175,-2.375],[0.189,-2.435],[0.205,-2.452],[0.252,-2.461],[0.272,-2.509],[0.277,-2.606],[0.261,-2.632],[0.217,-2.652],[0.212,-2.708],[0.379,-4.107],[0.406,-4.255],[0.462,-4.407],[0.547,-4.437],[0.577,-4.485],[0.591,-4.536],[0.554,-4.587],[0.554,-4.61],[0.628,-4.767],[0.649,-4.783],[0.713,-4.797],[0.753,-4.864],[0.753,-4.901],[0.716,-4.961],[0.785,-5.123],[0.824,-5.153],[0.866,-5.162],[1.23,-5.18],[1.272,-5.166],[1.309,-5.134],[1.614,-5.125],[1.674,-5.111],[1.701,-5.097],[1.741,-5.049],[1.801,-4.919],[1.791,-4.859],[1.653,-4.555],[1.404,-3.936],[1.279,-2.763],[1.325,-2.579],[1.385,-2.482],[1.443,-2.419],[1.563,-2.35],[1.688,-2.322],[2.999,-2.309],[3.029,-2.288],[3.043,-2.255],[2.95,-2.126],[2.932,-2.075],[2.936,-1.96],[2.957,-1.935],[2.985,-1.925],[3.096,-1.93],[3.13,-1.951],[3.103,-2.214],[3.103,-2.251],[3.128,-2.276],[3.156,-2.276],[3.216,-2.248],[3.322,-2.258],[3.391,-2.23],[3.511,-2.248],[3.553,-2.23],[3.613,-2.23],[3.673,-2.253],[3.756,-2.239],[3.807,-2.248],[3.848,-2.272],[3.959,-2.267],[4.051,-2.313],[5.912,-2.322],[6.037,-2.304],[6.166,-2.244],[6.261,-2.163],[6.445,-1.872],[6.54,-1.773],[6.605,-1.727],[6.757,-1.667],[7.043,-1.662],[7.069,-1.641],[7.082,-1.226],[7.138,-0.704],[7.138,-0.57],[7.096,-0.108],[7.071,-0.065],[7.029,-0.051],[6.78,-0.005],[5.035,0],[4.906,-0.023],[4.772,-0.023],[4.633,0],[4.527,0],[0.436,-0.028],[0.178,-0.046],[0.132,-0.065],[0.088,-0.108],[0.037,-0.229],[0.014,-0.381]],"features":{"through":[[[5.91,-2.071],[5.919,-1.798],[5.963,-1.768],[6.212,-1.773],[6.238,-1.808],[6.233,-1.84],[6.127,-2.015],[6.051,-2.087],[5.972,-2.119],[5.935,-2.115]],[[1.505,-2.001],[1.535,-1.958],[1.591,-1.935],[2.699,-1.93],[2.726,-1.944],[2.761,-1.992],[2.766,-2.057],[2.756,-2.075],[2.699,-2.124],[2.569,-2.133],[1.581,-2.128],[1.54,-2.105],[1.51,-2.066]],[[0.873,-2.703],[0.896,-2.634],[0.953,-2.604],[1.004,-2.618],[1.039,-2.657],[1.062,-2.768],[1.173,-3.797],[1.129,-3.86],[1.097,-3.869],[1.037,-3.851],[1.007,-3.821],[0.993,-3.793],[0.97,-3.622]],[[1.071,-4.121],[1.085,-4.093],[1.129,-4.063],[1.198,-4.072],[1.251,-4.135],[1.417,-4.545],[1.408,-4.592],[1.369,-4.622],[1.318,-4.617],[1.279,-4.582],[1.076,-4.181]],[[1.394,-4.864],[1.406,-4.852],[1.595,-4.857],[1.634,-4.892],[1.653,-4.933],[1.637,-4.963],[1.609,-4.968],[1.447,-4.968]]],"buttpad":[[[-0.03,0.076],[0.339,0.076],[0.339,-0.478],[0.353,-1.17],[0.386,-1.632],[0.441,-2.094],[0.515,-2.556],[0.584,-3.017],[0.616,-3.479],[0.663,-3.941],[0.695,-4.171],[0.732,-4.402],[0.824,-4.633],[0.94,-4.864],[1.055,-5.095],[1.11,-5.256],[-0.03,-5.256]]],"plate":[[[0.386,-1.632],[0.441,-2.094],[0.515,-2.556],[0.584,-3.017],[0.616,-3.479],[0.663,-3.941],[0.695,-4.171],[0.732,-4.402],[0.824,-4.633],[0.94,-4.864],[1.055,-5.095],[1.11,-5.256],[1.24,-5.256],[1.18,-5.095],[1.064,-4.864],[0.949,-4.633],[0.847,-4.402],[0.81,-4.171],[0.778,-3.941],[0.732,-3.479],[0.699,-3.017],[0.63,-2.556],[0.556,-2.094],[0.501,-1.632]]],"housing":[[[0.247,0.076],[7.219,0.076],[7.219,-1.632],[0.247,-1.632]]],"rear":[[[0.247,0.076],[3.479,0.076],[3.479,-0.663],[3.225,-1.17],[3.202,-1.378],[0.247,-1.378]]],"lever":[[[3.918,-1.434],[4.633,-1.378],[4.979,-1.392],[5.012,-1.424],[5.012,-1.531],[4.633,-1.567],[4.125,-2.223],[4.125,-2.371],[3.11,-2.371],[3.11,-1.946],[3.839,-1.817],[3.885,-1.54]]],"block":[[[4.125,-1.632],[7.219,-1.632],[7.219,-2.371],[4.125,-2.371]]],"frame":[[[0.247,-1.632],[4.125,-1.632],[4.125,-5.256],[0.247,-5.256]]],"window":[[[4.772,-1.632],[4.901,-1.632],[4.901,-1.965],[4.772,-1.965]]],"crosspin":[[[4.776,-1.535],[4.887,-1.535],[4.887,-1.646],[4.776,-1.646]]],"pivot":[[[3.945,-1.484],[4.093,-1.484],[4.093,-1.632],[3.945,-1.632]]],"qd":[[[5.233,-1.655],[5.815,-1.655],[5.815,-2.311],[5.233,-2.311]]],"pockets":[[[0.672,-1.692],[1.267,-1.692],[1.147,-1.817],[1.009,-1.955],[0.893,-2.094],[0.801,-2.218],[0.723,-2.334],[0.672,-2.334]],[[1.54,-1.715],[2.906,-1.715],[2.754,-2.223],[1.041,-2.223],[1.101,-2.117],[1.207,-1.965],[1.355,-1.817]],[[0.824,-2.556],[1.147,-2.556],[1.217,-2.671],[1.286,-3.802],[1.217,-3.941],[1.055,-3.978],[0.94,-3.918],[0.87,-3.479],[0.764,-2.694]],[[0.963,-4.01],[1.18,-3.996],[1.263,-4.056],[1.54,-4.587],[1.517,-4.67],[1.401,-4.689],[1.309,-4.633],[1.009,-4.171]]],"bar":[[[4.125,-2.218],[5.926,-2.218],[5.926,-2.311],[4.125,-2.311]]],"blockpocket":[[[4.601,-1.655],[5.233,-1.655],[5.233,-2.218],[4.601,-2.218]]],"cells":[[[0.478,-1.184],[0.552,-1.184],[0.552,-1.295],[0.478,-1.295]],[[0.838,-1.184],[1.032,-1.184],[1.032,-1.295],[0.838,-1.295]],[[1.724,-1.184],[1.909,-1.184],[1.909,-1.295],[1.724,-1.295]],[[2.616,-1.184],[2.8,-1.184],[2.8,-1.295],[2.616,-1.295]]]},"scaleRefs":["mft-battlelink-minimalist-stock.length","mft-battlelink-minimalist-stock.height"],"inputs":{"mft-battlelink-minimalist-stock.height":5.22,"mft-battlelink-minimalist-stock.length":7.084},"tolerance":0.008,"photo":"references/mft-battlelink-minimalist-stock 125d06ff6f12 (Mission First Tactical: BMSMIL_black_01, straight right side on white, 1567 x 1200)","method":"luminance < 235, closing ×2, largest piece, holes filled; scale from mft-battlelink-minimalist-stock.length = 7.084 in (x-extent 1546 px → 218.2 px/in) and mft-battlelink-minimalist-stock.height = 5.22 in (y-extent 1122 px → 214.9 px/in), which agree within 1.5%; mean 216.6 px/in; origin at x min, y max of the outline; Douglas-Peucker at 0.008 in with the extremes kept: 119 points (IoU 0.997 with the full outline); features through the same placement (through: reviewed pixel boxes; buttpad: reviewed pixel boxes; plate: reviewed pixel boxes; housing: reviewed pixel boxes; rear: reviewed pixel boxes; lever: reviewed pixel boxes; block: reviewed pixel boxes; frame: reviewed pixel boxes; window: reviewed pixel boxes; crosspin: reviewed pixel boxes; pivot: reviewed pixel boxes; qd: reviewed pixel boxes; pockets: reviewed pixel boxes; bar: reviewed pixel boxes; blockpocket: reviewed pixel boxes; cells: reviewed pixel boxes) (tools/trace.py)","via":"harvest","note":"The five openings are cut through. The lever, the pad's ridges and the paddle's ribs are in the outline. The frame's recessed panels and the ledge's cells are features; the markings aren't drawn."},"front":{"plane":"zy","origin":"the housing's top edge, centred: as the side profile, offset down to the tube axis","offset":{"y":"tube_axis_below_top"},"points":[[-0.809,-0.624],[-0.809,-0.651],[-0.763,-0.742],[-0.443,-1.235],[-0.34,-1.342],[-0.34,-1.601],[-0.311,-1.63],[0.311,-1.63],[0.34,-1.601],[0.34,-1.342],[0.443,-1.235],[0.458,-1.212],[0.783,-0.712],[0.809,-0.651],[0.809,-0.624],[0.767,-0.536],[0.721,-0.464],[0.5,-0.181],[0.414,-0.103],[0.391,-0.088],[0.185,-0.019],[0.162,0],[-0.002,0],[-0.162,0],[-0.185,-0.019],[-0.399,-0.092],[-0.5,-0.181],[-0.733,-0.479],[-0.794,-0.59]],"features":{"opening":[[[-0.032,-0.071],[-0.269,-0.128],[-0.357,-0.185],[-0.414,-0.242],[-0.468,-0.3],[-0.513,-0.357],[-0.555,-0.414],[-0.597,-0.471],[-0.632,-0.529],[-0.678,-0.586],[-0.7,-0.643],[-0.67,-0.7],[-0.628,-0.758],[-0.594,-0.815],[-0.552,-0.872],[-0.513,-0.93],[-0.471,-0.987],[-0.41,-1.044],[-0.357,-1.101],[-0.303,-1.159],[-0.261,-1.216],[-0.242,-1.273],[-0.239,-1.33],[-0.239,-1.544],[0.239,-1.544],[0.239,-1.33],[0.242,-1.273],[0.261,-1.216],[0.303,-1.159],[0.357,-1.101],[0.41,-1.044],[0.471,-0.987],[0.513,-0.93],[0.552,-0.872],[0.594,-0.815],[0.628,-0.758],[0.67,-0.7],[0.7,-0.643],[0.678,-0.586],[0.632,-0.529],[0.597,-0.471],[0.555,-0.414],[0.513,-0.357],[0.468,-0.3],[0.414,-0.242],[0.357,-0.185],[0.269,-0.128],[0.032,-0.071]]]},"scaleRefs":["mft-battlelink-minimalist-stock.mouth_height"],"inputs":{"mft-battlelink-minimalist-stock.mouth_height":1.63},"tolerance":0.004,"photo":"references/mft-battlelink-minimalist-stock f15b8c0be94f (Wing Tactical: the scorched dark earth stock straight from the front, into the tube's opening, 1280 x 1280)","method":"manual polygon (46 points picked on the photo); scale from mft-battlelink-minimalist-stock.mouth_height = 1.63 in (y-extent 427 px → 262.0 px/in); origin at x center, y max of the outline; Douglas-Peucker at 0.004 in with the extremes kept: 29 points (IoU 0.997 with the full outline); one reference only (the mouth's height from the side view); what has to fit in the opening is the check: a mil-spec tube and its rail, 1.448 in from top to foot, in the 385 px between the bore's top and the channel's floor; checks: width 1.619 ± 0.023 in vs mft-battlelink-minimalist-stock.body_width 1.61 ± 0.04 (provisional): agrees; features through the same placement (opening: reviewed pixel boxes) (tools/trace.py)","via":"harvest","note":"Seen from the front, not the rear; the section is symmetric (made so about the silhouette's middle). An arch over a ridge each side at the tube's height, leaning in under it to the neck round the indexing rail's channel. The opening is the keyed bore at the mouth."}},"gaps":[{"what":"Where the published 1.752 in width lies: the housing's mouth is 1.61 across, its rear part reads 1.69 ± 0.05 where it begins, and no view shows the butt or the top square (the rear part and the pad round it are drawn at the published width)","need":"a straight view of the butt or from above, or the maker's drawing"},{"what":"Its seat on the tube from a square photo (it is seated by its lock pin in the tube's front hole, ± 0.08 in; a seller's oblique of it on a rifle agrees, one hole out)","need":"a straight side photo of it on a lower with both receiver pins in view, at any position; or a published length of pull"},{"what":"The housing's section behind its mouth (its rear part is fuller under the ridge, with a ledge of four cells), and how deep each of the frame's panels and the cells is recessed (one reading, 0.25 in of web at one slot, stands for all)","need":"views from above and below, or an oblique with the camera fitted to it"},{"what":"The butt pad's face from the rear (its outline, its taper to the toe, the ridges' ends)","need":"a straight view of the butt"},{"what":"What the pins, the spring and the QD socket's cup are made of and finished in, and how deep the socket is","need":"the maker's or a seller's words; a view into the socket"},{"what":"A patent or drawing of it: the maker's virtual patent marking page (read 2026-10-13) lists one patent, for holsters; its 2013 release says 'patent pending'","need":"a patent number tied to the stock by the maker"}]},"midwest-combat-rail-15-handguard":{"id":"midwest-combat-rail-15-handguard","name":"Combat Rail One Piece Free Float Handguard, M-LOK™ (15\")","manufacturer":"Midwest Industries","sku":"MI-CRM15","url":"https://midwestindustriesinc.com/mi-combat-rail-one-piece-free-float-handguard-m-lok-tm/","category":"handguard","description":"Midwest Industries' 15 in free-float M-LOK handguard, with the barrel nut, torque plate and two clamp screws it mounts by. The maker's page (one page for thirteen lengths; this one is MI-CRM15): \"4140 Heat Treated Barrel Nut\", \"Barrel Nut and Wrench Included\", \"Features Patented 4140 Heat Treated Torque Plate\", \"6061 Aluminum Type 3 Hard Coat Anodized\", \"Continuous MIL-STD 1913 Picatinny Top rail\", \"Two Integral Anti-Rotation QD Sling Sockets\", \"Super Slim 1.5” Outside and 1.3” Inside Diameter\", \"Seven Sides of M-Lok\", \"5-Slot Polymer M-Lok rail included\"; and \"This handguard is compatible with standard forged upper receivers.\", \"NOT FOR USE ON GAS PISTON AR’s!\". Magpul® and M-LOK™ are trademarks of Magpul Industries Corp.","weight":"midwest-combat-rail-15-handguard.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"mount":{"origin":[0,0,0],"note":"The receiver's front face on the bore axis, +x toward the muzzle."},"mlok":{"origin":["{.mlok_side_slot0_x}",0,0],"note":"On the bore's axis at the side faces' rearmost full M-LOK slot's centre (index 0), +x toward the muzzle; the faces are angles about this axis. The underside's row begins at the same place."},"mlok_diag":{"origin":["{.mlok_diag_slot0_x}",0,0],"note":"The same axis at the rearmost slot's centre of the four faces at 45 degrees: one slot pitch (40 mm) behind the side faces' first, where the side faces and the underside have a short cut and a sling socket."},"top_rail":{"origin":["{.rail_slot0_x}","{.rail_top_above_bore}",0],"note":"The rail's top at its rearmost slot's centre, +x toward the muzzle (picatinny: index = slot number). Its own rail: the receiver's is the receiver's."}},"interfaces":{"handguard_mount":{"type":"ar15.handguard_mount","role":"handguard","anchor":"mount","params":{"nut":"standard"},"flips":false,"note":"The maker: \"This handguard is compatible with standard forged upper receivers.\" and, of the nut it comes with, \"Barrel Nut and Wrench Included\"; its sheet: \"Screw the barrel nut onto the upper receiver threads with the four notches facing the muzzle.\", then \"Slide the handguard onto the barrel nut and align with the upper rail by hand.\" Wing Tactical: \"Compatibility: Mil-Spec AR-15 upper\". Not said of every receiver: \"Due to the many different dimensions in BILLET UPPER RECEIVERS on the market, please contact your billet upper receiver manufacture to insure fit of this handguard.\" (its sheet: \"May not be compatible with billet upper receivers.\"), and \"NOT FOR USE ON GAS PISTON AR’s!\": neither is a check here (the catalog's receivers are forged and its gas systems direct). Where its rear face stops isn't published: it is drawn against the receiver's front shoulder (rear_face_x)."},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}","beyond_seam":true,"seam_behind":"receiver","seam_ahead":"handguard"},"flips":false},"mlok":{"type":"mlok","role":"slots","anchor":"mlok","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_side_slots}","interval":"={std.mlok.interval}","face_distance":"={.width} / 2","bore":"={.inside_diameter}","reach_inside":"={.reach_inside}"},"faces":{"right":{"angle":90,"note":"the rifle's right side (+z)"},"left":{"angle":-90},"bottom":{"angle":180,"note":"the underside (6 o'clock)"}},"flips":false,"note":"The side faces and the underside: seven full slots each. Behind the first, each has a short cut about half a slot long, which isn't offered as a place (no page says what it takes). How far an accessory's nuts may reach inside depends on the barrel and gas block under it, other parts: reach_inside has no figure, so that check reads as unmade."},"mlok_between":{"type":"mlok","role":"slots","anchor":"mlok_diag","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_diag_slots}","interval":"={std.mlok.interval}","face_distance":"={.diag_face_distance}","bore":"={.inside_diameter}","reach_inside":"={.reach_inside}"},"faces":{"right_upper":{"angle":45,"note":"between the rail and the right side (1:30)"},"right_lower":{"angle":135,"note":"between the right side and the bottom (4:30)"},"left_lower":{"angle":-135},"left_upper":{"angle":-45}},"flips":false,"note":"The four faces at 45° (Wing Tactical: \"allow user to mount accessories at 45-degree\"), eight slots each. Their rows read 0.02 to 0.03 in nearer the side faces than where a line from the bore meets the face square on; an accessory is placed on that line."}},"materials":{"body":{"label":"Handguard","finish":"anodized","recolorable":true,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized","color":"placeholder-black","sku":"MI-CRM15","source":"https://midwestindustriesinc.com/mi-combat-rail-one-piece-free-float-handguard-m-lok-tm/"},"fde":{"label":"Magpul FDE","finish":"cerakote","color":"midwest-fde-cerakote","sku":"MI-CRM15-FDE","source":"https://midwestindustriesinc.com/mi-combat-rail-one-piece-free-float-handguard-magpul-fde-m-lok-tm/"}},"default":"black","note":"The maker: \"6061 Aluminum Type 3 Hard Coat Anodized\"; Wing Tactical: \"Finish: Mil-Spec Type III Hardcoat Anodized\". And, on a page of its own (\"Combat Rail One Piece Free Float Handguard, Magpul FDE M-LOK™\", this length MI-CRM15-FDE, the same installed weight): \"Custom Cerakote Magpul FDE\". The whole handguard is one piece and one colour in both, its rail, its tabs, its clamp lug and its sling sockets with it (\"Integral\"; the maker's picture of the Flat Dark Earth one, MI-CRM15-FDE-2, is tan all over). What comes with it is black in both: the slot `hardware`. A black on sealed anodize isn't fitted to a photo: it is the catalog's stand-in black. The marks engraved on it (the maker's name under the rail, its mark in the side faces' pockets, the numbers in the rail's slots) aren't drawn."},"hardware":{"label":"Barrel nut, clamp screws and torque plate","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The steel that comes with it and goes on the rifle with it: the barrel nut inside its rear end (the maker: \"4140 Heat Treated Barrel Nut\"), the two socket head cap screws across its clamp lug and the torque plate in the lug's split (\"Patented 4140 Heat Treated Torque Plate\"). Black in every picture of it, on the black handguard and on the Flat Dark Earth one (the maker's MI-CRM15-FDE-2: two black screw heads in the tan lug, the nut dark inside). The finish's name isn't on a page read, and a black on steel isn't fitted to a photo."}},"components":{},"geometry":{"model":"midwest-combat-rail-15-handguard.glb","components":{},"approximations":["Its section is drawn from the maker's 1.5 in across the side faces, Wing Tactical's 1.97 in of height and Primary Arms' two level photos of this length; no view shows it square on. It is taken as a regular octagon about the bore, every face 0.75 in out and the faces between at 45° (the maker gives one \"Outside Diameter\"; a seller says accessories go on \"at 45-degree\"): the level photo has the bottom flat 0.75 below the bore and the side faces' flats centred on it, and the narrow faces that break the corners between the side faces and the faces beside them stand where a regular octagon's corners are. Those narrow faces, and the like ones along the bottom flat, are drawn as flat chamfers 0.07 in back each way.","Its length is the maker's 15.0 in from its rear face to the tips of its side faces (the level photos read 14.95). The muzzle end is cut as those photos show it from the side, two straight slopes from the tips, one up to the neck's front under the rail's end and a longer one down to the bottom flat, and cut square across (how the slopes run across the faces isn't seen).","The rail's head is MIL-STD-1913's in section (the maker: \"MIL-STD 1913 Picatinny Top rail\"), its lower faces carried on to the neck's walls, its 36 slots the standard's from the first's place, and its two ends square (the photos show its front end's upper edge broken). The neck under it is 0.69 in wide with walls of 0.06 and the channel between them open into the tube from end to end, its roof 0.15 below the rail's top: the walls and the roof are read on one oblique view of the rear end.","Inside, a round bore at the barrel nut's diameter for the nut's length (how far the round part really runs isn't seen), then the maker's 1.3 in across inner flats that follow the outside, with sharp corners (the photo of the muzzle end shows them a little round).","Seven M-LOK slots on each side face and on the underside and eight on each of the four faces between, at the standard's size and pitch; the rows of the faces between are cut at the heights the level photo's light through them gives. The underside's row is counted on a seller's view from below of a Combat Rail whose length isn't stated (it shows the same eight on the lower faces). The short cut behind the first slot of the sides and the underside is drawn as wide as a slot and 0.64 in long.","The 32 round holes a side through the neck are cut straight across, one under each rail slot from the fifth. Each sling socket is its hole through the side wall in a flat cut 0.035 in below the face (weakly read); the socket's lip inside and the notches that keep a swivel from turning aren't drawn, and light shows through from one to the other as in the photos.","The blind pockets at the rear end (one in each face between where a ninth slot would be, a shorter one in each side face) are cut 0.02 in deep with an M-LOK slot's corners: their depth is read off a line a pixel or two wide. The small scallops along the six broken corners are each a ball's cut, sixteen a corner every 20 mm from the first slot of the faces between; their stations are read at the two ends of the row and their size on four of them.","The clamp lug under the rear end is a block as wide as it reads on a view from behind (0.51 in), flat underneath with a round rear corner and a straight ramp at its front, split along its middle up into the bore as far as the ramp (how far the split really runs isn't seen).","Behind the rear face, each tab is the wall of an upper face carried back 0.165 in, as thick as the wall is over the barrel nut, its end square (the photos show it cut to a blunt point) and its inner face on a mil-spec receiver's flat side under the rail (0.638 in between the two: not seen square on).","The steel that goes on the rifle with it is drawn as pieces of their own, black on a handguard of either colour: the barrel nut as a plain ring in the rear bore, from the receiver thread's diameter out to its own (its thread, the sleeve ahead of the thread that bears on the barrel's flange, its groove, its notches and its knurl aren't drawn); the two clamp screws as plain rounds, a shank across the lug and a head standing on its right side with its hexagon socket, cut half the head deep (its depth isn't read); the torque plate as a plain plate in the lug's split under the nut (its post, which goes in the nut's groove, isn't drawn).","It is drawn with its rear face against the receiver's front shoulder: no page says where it stops and no photo of it mounted is on file. Its rail's first slot then stands 0.01 in from where the receiver's own slots would continue.","Its aluminium by the model is 5.53 cubic inches, 8.7 oz, and the steel drawn with it 0.29 cubic inches, 1.3 oz: 10.0 oz against the maker's 11.4 oz installed, an eighth light. What the rest is isn't known: the nut's sleeve ahead of its thread isn't weighed (it could be most of an ounce), and the neck's walls, the nut's diameter and the pockets are the weakest readings.","Not drawn: the marks engraved on it (the maker's name and patent number under the rail on the right, a CAGE code on the left, the maker's mark in the side faces' pockets, the numbers on the rail's lands), and what else is in the box (the wrench, the five-slot polymer rail, the keys)."],"ledger":["midwest-combat-rail-15-handguard.length","midwest-combat-rail-15-handguard.width","midwest-combat-rail-15-handguard.height","midwest-combat-rail-15-handguard.inside_diameter","midwest-combat-rail-15-handguard.rear_x"]},"profiles":{"side":{"plane":"xy","origin":"the tabs' rear ends (behind the rear face) and the rail's top","offset":{"x":"rear_x","y":"rail_top_above_bore"},"points":[[0,-0.632],[0,-0.756],[0.074,-0.899],[0.147,-0.903],[0.147,-1.515],[0.263,-1.918],[0.271,-2.197],[0.302,-2.267],[0.345,-2.309],[0.438,-2.34],[1.344,-2.348],[1.484,-2.317],[1.538,-2.278],[1.782,-2.026],[1.728,-2.05],[1.864,-1.953],[14.626,-1.984],[14.727,-1.945],[14.82,-1.883],[15.106,-1.643],[15.203,-1.538],[15.211,-0.918],[15.141,-0.585],[15.118,-0.546],[15.118,-0.236],[15.133,-0.12],[15.044,-0.023],[14.711,-0.015],[14.595,-0.039],[14.568,-0.058],[14.56,-0.136],[14.51,-0.139],[14.498,-0.035],[14.479,-0.015],[14.316,-0.015],[14.2,-0.046],[14.18,-0.074],[14.18,-0.136],[14.122,-0.139],[14.111,-0.043],[14.091,-0.015],[13.921,-0.015],[13.82,-0.039],[13.801,-0.058],[13.793,-0.136],[13.735,-0.139],[13.704,-0.015],[13.525,-0.015],[13.429,-0.043],[13.402,-0.139],[13.34,-0.139],[13.309,-0.015],[13.13,-0.015],[13.037,-0.046],[13.033,-0.112],[13.099,-0.108],[13.107,-0.077],[13.115,-0.116],[13.134,-0.097],[13.13,-0.132],[12.952,-0.139],[12.933,-0.128],[12.921,-0.015],[12.735,-0.015],[12.708,-0.035],[12.731,-0.043],[12.708,-0.05],[12.739,-0.058],[12.743,-0.132],[12.541,-0.132],[12.526,-0.015],[12.355,-0.008],[12.336,-0.019],[12.34,-0.132],[12.146,-0.132],[12.142,-0.05],[12.123,-0.008],[11.952,-0.008],[11.941,-0.019],[11.956,-0.112],[11.945,-0.132],[11.751,-0.132],[11.728,-0.008],[11.557,-0.008],[11.538,-0.05],[11.553,-0.058],[11.55,-0.132],[11.356,-0.132],[11.333,-0.008],[11.162,-0.008],[11.15,-0.019],[11.154,-0.132],[10.961,-0.132],[10.937,-0.008],[10.767,-0.008],[10.755,-0.019],[10.763,-0.12],[10.751,-0.132],[10.565,-0.132],[10.542,-0.008],[10.364,-0.008],[10.364,-0.124],[10.17,-0.132],[10.147,-0.008],[9.969,-0.008],[9.957,-0.019],[9.965,-0.12],[9.876,-0.132],[9.76,-0.124],[9.756,-0.012],[9.729,0],[9.574,-0.008],[9.562,-0.019],[9.566,-0.124],[9.364,-0.124],[9.361,-0.019],[9.341,0],[9.186,0],[9.167,-0.012],[9.163,-0.124],[8.961,-0.124],[8.958,-0.012],[8.946,0],[8.791,0],[8.772,-0.012],[8.772,-0.112],[8.76,-0.124],[8.566,-0.124],[8.562,-0.012],[8.551,0],[8.388,0],[8.365,-0.124],[8.171,-0.124],[8.163,-0.008],[7.993,0],[7.973,-0.012],[7.97,-0.124],[7.776,-0.124],[7.764,-0.112],[7.772,-0.027],[7.753,0],[7.59,0],[7.567,-0.124],[7.373,-0.124],[7.377,-0.027],[7.357,0],[7.195,0],[7.171,-0.124],[7.017,-0.124],[7.009,-0.093],[7.001,-0.124],[6.978,-0.124],[6.974,-0.012],[6.962,0],[6.8,0],[6.78,-0.027],[6.776,-0.124],[6.583,-0.124],[6.571,-0.112],[6.579,-0.012],[6.567,0],[6.404,0],[6.385,-0.019],[6.385,-0.112],[6.373,-0.124],[6.187,-0.124],[6.176,-0.112],[6.184,-0.012],[6.172,0],[6.009,0],[5.99,-0.012],[5.99,-0.105],[5.97,-0.124],[5.8,-0.124],[5.781,-0.105],[5.788,-0.012],[5.777,0],[5.606,0],[5.583,-0.124],[5.397,-0.124],[5.385,-0.066],[5.401,-0.019],[5.382,0],[5.219,0],[5.199,-0.012],[5.188,-0.124],[5.002,-0.124],[4.99,-0.043],[5.017,-0.015],[4.986,0],[4.824,0],[4.804,-0.019],[4.793,-0.124],[4.607,-0.124],[4.595,-0.112],[4.603,-0.027],[4.638,-0.031],[4.661,-0.062],[4.673,-0.035],[4.661,-0.023],[4.591,0],[4.428,0],[4.409,-0.027],[4.397,-0.124],[4.204,-0.124],[4.208,-0.035],[4.227,-0.023],[4.297,-0.062],[4.289,-0.031],[4.196,0],[4.033,0],[4.002,-0.124],[3.824,-0.124],[3.805,-0.105],[3.812,-0.043],[3.824,-0.023],[3.855,-0.062],[3.867,-0.027],[3.855,-0.015],[3.809,0],[3.646,0],[3.626,-0.019],[3.607,-0.124],[3.452,-0.124],[3.417,-0.112],[3.425,-0.027],[3.491,-0.039],[3.502,-0.066],[3.526,-0.074],[3.53,-0.116],[3.541,-0.081],[3.522,-0.031],[3.413,0],[3.258,0],[3.239,-0.012],[3.223,-0.12],[3.165,-0.124],[3.134,-0.031],[3.018,0],[2.871,0],[2.844,-0.019],[2.824,-0.124],[2.646,-0.124],[2.635,-0.066],[2.662,-0.062],[2.65,-0.074],[2.669,-0.077],[2.669,-0.046],[2.685,-0.077],[2.755,-0.077],[2.77,-0.108],[2.762,-0.039],[2.631,0],[2.499,0],[2.456,-0.019],[2.437,-0.124],[2.251,-0.124],[2.247,-0.097],[2.274,-0.108],[2.282,-0.077],[2.298,-0.101],[2.375,-0.085],[2.39,-0.108],[2.394,-0.066],[2.375,-0.031],[2.274,-0.008],[2.104,0],[2.069,-0.019],[2.05,-0.124],[1.864,-0.124],[1.864,-0.085],[1.871,-0.116],[1.918,-0.093],[2.011,-0.116],[2.007,-0.05],[1.995,-0.031],[1.817,0],[1.693,-0.008],[1.662,-0.124],[1.492,-0.124],[1.48,-0.105],[1.499,-0.093],[1.639,-0.116],[1.635,-0.058],[1.616,-0.031],[1.368,0],[1.302,-0.012],[1.275,-0.124],[1.255,-0.05],[1.236,-0.031],[1.096,-0.008],[0.926,-0.008],[0.887,-0.093],[0.864,-0.031],[0.717,-0.008],[0.267,0],[0.205,-0.008],[0.178,-0.081],[0.209,-0.205],[0.209,-0.515],[0.031,-0.523]],"scaleRefs":["midwest-combat-rail-15-handguard.overall_length","midwest-combat-rail-15-handguard.height_over_lug"],"inputs":{"midwest-combat-rail-15-handguard.height_over_lug":2.355,"midwest-combat-rail-15-handguard.overall_length":15.165},"tolerance":0.01,"photo":"references/midwest-combat-rail-15-handguard 569d57096244 (Primary Arms' gallery for MI-CRM-15.0, MI-CRM-15.0_01.jpg: the handguard alone, its right side seen level, muzzle to the right, 2200 x 1467)","method":"luminance < 200, largest piece, holes filled; scale from midwest-combat-rail-15-handguard.overall_length = 15.165 in (x-extent 1963 px → 129.4 px/in) and midwest-combat-rail-15-handguard.height_over_lug = 2.355 in (y-extent 303 px → 128.7 px/in), which agree within 0.6%; mean 129.1 px/in; origin at x min, y max of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 301 points (IoU 0.996 with the full outline) (tools/trace.py)","via":"harvest","note":"The slots and holes are inside the outline (filled); the model cuts them. A silhouette from 35 in: its ends and its lug are near edges, 0.02 to 0.05 in outside the mid-plane's. The model is built from the ledger, not from this."}},"gaps":[{"what":"Where it stops on the receiver (rear_face_x: drawn against the front shoulder with no gap)","need":"A photo of this handguard mounted on a forged upper with the receiver's pins in frame; the maker's sheet says only that it slides onto its barrel nut"},{"what":"Its section square on (the faces' angle, the neck's walls, the channel under the rail, the walls' thickness)","need":"An end view with a known size in frame, or the maker's drawing: none is published"},{"what":"Its weight without its barrel nut, torque plate and screws (weight_handguard is worked out from sizes read off photos)","need":"A page that weighs the handguard alone, or the nut alone"},{"what":"The room inside its faces before the barrel (reach_inside: what an M-LOK accessory's nuts may take)","need":"The barrel's and the gas block's size under it, from the parts a build puts there"},{"what":"What its short cuts behind the side faces' and the underside's slots are for, and whether they take an M-LOK nut","need":"The maker's word"}]},"midwest-industries-drop-in-mlok-carbine":{"id":"midwest-industries-drop-in-mlok-carbine","name":"AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Carbine)","manufacturer":"Midwest Industries","sku":"MI-17M","url":"https://www.midwestindustriesinc.com/product-p/mi-17m-blk.htm","category":"handguard","description":"Midwest Industries' two-piece aluminium drop-in handguard, carbine length (MI-17M; one page, SKU AR15M16TWOPI, for the carbine, mid and rifle lengths). The maker: \"Drop-in, no gunsmith installation, installs in minutes like factory handguards!\", \"Five anti rotation QD socket locations for QD sling swivels\", \"Monolithic type continuous top rail\", \"MIL-STD 1913 top rail\", \"Constructed from 6061 aluminum hard coat anodized\", \"1.83\\\" wide and 2.25\\\" tall\", and \"MI-17M (Carbine) – Only for use with round handguard caps\". It goes on the rifle's own barrel nut and delta ring and the cap behind its front sight base: no free-float nut of its own. M-LOK® is a trademark of Magpul Industries Corp.","weight":"midwest-industries-drop-in-mlok-carbine.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"needs":{"slots":["barrel_nut","delta_ring","handguard_cap"],"says":"The maker: \"Drop-in, no gunsmith installation, installs in minutes like factory handguards!\" and \"MI-17M (Carbine) – Only for use with round handguard caps\"; its instructions: \"Pull the delta ring to the rear and remove both sections of the plastic handguards, pulling out from the delta ring end first.\"","source":"https://www.midwestindustriesinc.com/product-p/mi-17m-blk.htm"},"anchors":{"mount":{"origin":[0,0,0],"note":"The receiver's front face on the bore axis, +x toward the muzzle. Its rear end (the rear flanges' end) stands in the delta ring's skirt against the lip, rear_x ahead of it."},"top_rail":{"origin":["{.rail_slot0_x}","{.rail_top_above_bore}",0],"note":"The rail's top at its rearmost slot's centre, +x toward the muzzle (picatinny: index = slot number). Its own rail, level with the receiver's."},"mlok":{"origin":["{.mlok_slot0_x}","{.rail_top_above_bore} - {.mlok_below_top}",0],"note":"At the lower side faces' rearmost M-LOK slot's centre, on the line along the handguard at the row's height (below the bore: the row is on the lower half), +x toward the muzzle; the faces are angles about this line."},"cap_seat":{"origin":["{.rear_x} + {.mounting_length}",0,0],"note":"The end of what of its front goes into the cap, on the bore axis: its mounting length ahead of its rear end. The cap seats it here (its pocket, the inside of its face), and its rear flanges then stand in the delta ring as far as that leaves them."}},"interfaces":{"cap_seat":{"type":"ar15.handguard_front","role":"handguard","anchor":"cap_seat","params":{},"flips":false,"note":"Seated by the cap (D97): its maker's \"installs in minutes like factory handguards!\"; between the delta ring's lip and the cap's face it is as long as the room (mounting_length)."},"handguard_mount":{"type":"ar15.handguard_mount","role":"handguard","anchor":"mount","params":{"nut":"standard"},"flips":false,"note":"On the rifle's own barrel nut and delta ring: the maker, \"Drop-in, no gunsmith installation, installs in minutes like factory handguards!\"; its instructions, \"Pull the delta ring to the rear and remove both sections of the plastic handguards, pulling out from the delta ring end first.\", \"Install the top section, hinge in from the front of the rifle to the rear.\", \"Install the lower section again hinge in from the front of the rifle to the rear.\" Placed by the standard's delta ring (rear_x)."},"drop_in":{"type":"ar15.drop_in","role":"handguard","params":{"shape":"round"},"flips":false,"note":"The maker (its page, read on the harvested copy): \"MI-17M (Carbine) – Only for use with round handguard caps\"."},"gas_system":{"type":"ar15.gas_system","role":"handguard","params":{"length":"carbine"},"flips":false,"note":"The maker's length option is \"Carbine\" (MI-17M), and the cap sentence names it \"MI-17M (Carbine)\"."},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}","beyond_seam":true,"seam_behind":"receiver","seam_ahead":"handguard"},"flips":false,"note":"The maker: \"Monolithic type continuous top rail\", \"MIL-STD 1913 top rail\". Behind its first land a plain tongue reaches back over the delta ring (no slots)."},"mlok":{"type":"mlok","role":"slots","anchor":"mlok","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_slots}","interval":"={std.mlok.interval}","face_distance":"={.mlok_face_distance}","reach_inside":"={.reach_inside}"},"faces":{"right":{"angle":90,"note":"the rifle's right side (+z)"},"left":{"angle":-90,"note":"the left, the right's mirror (assumed)"}},"flips":false,"note":"The maker's page names M-LOK and says no more of it; three slots a side on the lower half, counted on its photo. How far an accessory's nuts may reach inside depends on the barrel under it: reach_inside has no figure, so that check reads as unmade."}},"materials":{"body":{"label":"Handguard","finish":"anodized","recolorable":true,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized","color":"placeholder-black","sku":"MI-17M","source":"https://www.midwestindustriesinc.com/product-p/mi-17m-blk.htm"}},"default":"black","note":"The maker: \"Constructed from 6061 aluminum hard coat anodized\". Black is the one colour the page offers (its options are lengths alone; the picture is MI-17M-BLK-2 and the page's address mi-17m-blk). A black on sealed anodize isn't fitted to a photo: it is the catalog's stand-in black. The rear flanges show in the photo as dark as the body and are drawn in its look; the pins that hold them aren't drawn. The engraving (MI, MIDWEST INDUSTRIES, Made in U.S.A.) isn't drawn."}},"components":{},"geometry":{"model":"midwest-industries-drop-in-mlok-carbine.glb","components":{},"approximations":["Every place and height on it is read through a camera fitted to the maker's one photo of this length (a three-quarter view from behind its right side and above, as the other lengths' are): the rail's 15 slots and the right side's 3 M-LOK slots, both the standards', fix the camera, and the bottom then reads within 0.03 of the maker's height. No view is level and none looks at the left side, the underside or into either end: the left is drawn as the right's mirror.","One model of both halves (the seam a groove along each side between the upper half's side face and the lower half's): they come in one box, in one colour, and are never apart on a rifle.","Its section: the rail's head (MIL-STD-1913's, from the ledger) on a neck (the head's lower faces carried on at 45 degrees to the neck's top, the neck upright from there) down to a flat shelf out to the upper half's side faces (1.70 across: assumed, the lower half's top shows as a ledge outside them), the neck hollow over the gas tube up to a web under the rail's slots (its roof assumed); the lower half's side faces at the maker's 1.83; a lower bevel each side down to the bottom flat at the maker's 2.25 (its width read on the bottom's silhouette); flat faces throughout.","Its wall is 0.08 in (assumed: no view looks into an end; set near the maker's installed weight at aluminium's density), each half's inside its own section less the wall, open from end to end.","The rear flanges that go into the delta ring are drawn as a round collar split at the seam each side and notched over the gas tube, from the ring's lip to each half's rear face, inside the ring's skirt and outside the barrel nut's flange (their diameters assumed); the photo shows them as dark as the body, each held by two pins whose heads aren't drawn.","The rail's tongue reaches back over the delta ring to the upper receiver's front face (it reads a few hundredths behind it, inside the readings' ±: drawn bearing on it), a plate level with the rail's top in the head's section, 0.12 in deep (assumed). The rail's slots are the standard's on the pitch from the first's place, the first between the tongue and the first land.","Cut through each side: 7 round holes along the upper side face and a long one at its front, 8 round holes along the lower bevel, 3 M-LOK slots at the standard's size on the lower side face, and two QD sockets on the M-LOK row, all where the camera reads them. The sockets' anti-rotation notches and the fifth socket the maker counts (not seen: perhaps under the bottom) aren't drawn.","Its front: the upper half rounds over at its top front corner (radius assumed); the bottom flat's front part, from where the photo shows its step, is cut up 0.12 in (assumed). The round cap stands inside its front end, which reaches 0.31 in over the front sight base's rear; what inside it bears in the cap isn't seen and isn't drawn: it is seated there by its mounting length, the room the rifle holds it in. What of its front then stands in the front sight base's space is cut from its inside with 0.02 in to spare all round the base (its own model, placed at its rear face: base_rear_x), which leaves the rail's front end and the upper half's front following the base's sloped rear leg.","The maker's overall length, 7 in, is the rail's whole length by its photo (7.09)."],"ledger":["midwest-industries-drop-in-mlok-carbine.length","midwest-industries-drop-in-mlok-carbine.overall_length","midwest-industries-drop-in-mlok-carbine.width","midwest-industries-drop-in-mlok-carbine.height","midwest-industries-drop-in-mlok-carbine.rear_x","midwest-industries-drop-in-mlok-carbine.mounting_length"]},"profiles":{},"gaps":[{"what":"How deep its rail's neck runs before the upper half's top (a shelf 0.41 in under the rail's top as read, on one oblique photo, the engraved face under the head taken for the neck's side as on the maker's Combat Rail; read as a shoulder sloping out from the head instead, 17 of the clamps on file stood in it); Aimpoint's PRO stands on that shelf beside the neck as drawn (app/tests/rail-clamps.test.ts), and every other clamp on file clears it","need":"A view along it from either end, or a photo of a clamp on its rail from the side"},{"what":"A level view of either side, the underside (the fifth QD socket, any slots or holes there) and the left side","need":"A seller's or a buyer's photos of an MI-17M from the side, from below and from the left: every place on file is read through one oblique photo"},{"what":"Its section square on, its wall and the upper half's width","need":"An end view with a known size in frame (a photo into either end)"},{"what":"What bears in the cap at its front, and how far its front reaches over the front sight base","need":"A photo of it installed on an A2 front sight base, from the side"},{"what":"Where the round cap sits inside its front end (the cap's place on a carbine barrel against its photo's front)","need":"A photo of it installed on a carbine-length rifle with an A2 front sight base"}]},"midwest-industries-drop-in-mlok-mid":{"id":"midwest-industries-drop-in-mlok-mid","name":"AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Mid-Length)","manufacturer":"Midwest Industries","sku":"MI-18M","url":"https://www.midwestindustriesinc.com/product-p/mi-18m-blk.htm","category":"handguard","description":"Midwest Industries' two-piece aluminium drop-in handguard, mid-length (MI-18M; one page, SKU AR15M16TWOPI, for the carbine, mid and rifle lengths). The maker: \"Drop-in, no gunsmith installation, installs in minutes like factory handguards!\", \"Five anti rotation QD socket locations for QD sling swivels\", \"Monolithic type continuous top rail\", \"MIL-STD 1913 top rail\", \"Constructed from 6061 aluminum hard coat anodized\", \"1.83\\\" wide and 2.25\\\" tall\", and \"MI-18M (Mid-Length) – Only for use with triangle handguard caps\". It goes on the rifle's own barrel nut and delta ring and the cap behind its front sight base: no free-float nut of its own. M-LOK® is a trademark of Magpul Industries Corp.","weight":"midwest-industries-drop-in-mlok-mid.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"needs":{"slots":["barrel_nut","delta_ring","handguard_cap"],"says":"The maker: \"Drop-in, no gunsmith installation, installs in minutes like factory handguards!\" and \"MI-18M (Mid-Length) – Only for use with triangle handguard caps\"; its instructions: \"Pull the delta ring to the rear and remove both sections of the plastic handguards, pulling out from the delta ring end first.\"","source":"https://www.midwestindustriesinc.com/product-p/mi-18m-blk.htm"},"anchors":{"mount":{"origin":[0,0,0],"note":"The receiver's front face on the bore axis, +x toward the muzzle. Its rear end (the rear flanges' end) stands in the delta ring's skirt against the lip, rear_x ahead of it."},"top_rail":{"origin":["{.rail_slot0_x}","{.rail_top_above_bore}",0],"note":"The rail's top at its rearmost slot's centre, +x toward the muzzle (picatinny: index = slot number). Its own rail, level with the receiver's."},"mlok":{"origin":["{.mlok_slot0_x}","{.rail_top_above_bore} - {.mlok_below_top}",0],"note":"At the lower side faces' rearmost M-LOK slot's centre, on the line along the handguard at the row's height (below the bore: the row is on the lower half), +x toward the muzzle; the faces are angles about this line."},"cap_seat":{"origin":["{.rear_x} + {.mounting_length}",0,0],"note":"The end of what of its front goes into the cap, on the bore axis: its mounting length ahead of its rear end. The cap seats it here (its pocket, the inside of its face), and its rear flanges then stand in the delta ring as far as that leaves them."}},"interfaces":{"cap_seat":{"type":"ar15.handguard_front","role":"handguard","anchor":"cap_seat","params":{},"flips":false,"note":"Seated by the cap (D97): its maker's \"installs in minutes like factory handguards!\"; between the delta ring's lip and the cap's face it is as long as the room (mounting_length)."},"handguard_mount":{"type":"ar15.handguard_mount","role":"handguard","anchor":"mount","params":{"nut":"standard"},"flips":false,"note":"On the rifle's own barrel nut and delta ring: the maker, \"Drop-in, no gunsmith installation, installs in minutes like factory handguards!\"; its instructions, \"Pull the delta ring to the rear and remove both sections of the plastic handguards, pulling out from the delta ring end first.\", \"Install the top section, hinge in from the front of the rifle to the rear.\", \"Install the lower section again hinge in from the front of the rifle to the rear.\" Placed by the standard's delta ring (rear_x)."},"drop_in":{"type":"ar15.drop_in","role":"handguard","params":{"shape":"triangle"},"flips":false,"note":"The maker (its page, read on the harvested copy): \"MI-18M (Mid-Length) – Only for use with triangle handguard caps\"."},"gas_system":{"type":"ar15.gas_system","role":"handguard","params":{"length":"mid"},"flips":false,"note":"The maker's length option is \"Mid-Length\" (MI-18M), and the cap sentence names it \"MI-18M (Mid-Length)\"."},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}","beyond_seam":true,"seam_behind":"receiver","seam_ahead":"handguard"},"flips":false,"note":"The maker: \"Monolithic type continuous top rail\", \"MIL-STD 1913 top rail\". Behind its first land a plain tongue reaches back over the delta ring (no slots)."},"mlok":{"type":"mlok","role":"slots","anchor":"mlok","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_slots}","interval":"={std.mlok.interval}","face_distance":"={.mlok_face_distance}","reach_inside":"={.reach_inside}"},"faces":{"right":{"angle":90,"note":"the rifle's right side (+z)"},"left":{"angle":-90,"note":"the left, the right's mirror (assumed)"}},"flips":false,"note":"The maker's page names M-LOK and says no more of it; four slots a side on the lower half, counted on its photo. How far an accessory's nuts may reach inside depends on the barrel under it: reach_inside has no figure, so that check reads as unmade."}},"materials":{"body":{"label":"Handguard","finish":"anodized","recolorable":true,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized","color":"placeholder-black","sku":"MI-18M","source":"https://www.midwestindustriesinc.com/product-p/mi-18m-blk.htm"}},"default":"black","note":"The maker: \"Constructed from 6061 aluminum hard coat anodized\". Black is the one colour the page offers (its options are lengths alone; the picture is MI-18M-BLK-2 and the page's address mi-18m-blk). A black on sealed anodize isn't fitted to a photo: it is the catalog's stand-in black. The rear flanges show in the photo as dark as the body and are drawn in its look; the pins that hold them aren't drawn. The engraving (MI, MIDWEST INDUSTRIES, Made in U.S.A.) isn't drawn."}},"components":{},"geometry":{"model":"midwest-industries-drop-in-mlok-mid.glb","components":{},"approximations":["Every place and height on it is read through a camera fitted to the maker's one photo of this length (a three-quarter view from behind its right side and above, as the other lengths' are): the rail's 20 slots and the right side's 4 M-LOK slots, both the standards', fix the camera, and the bottom then reads within 0.03 of the maker's height. No view is level and none looks at the left side, the underside or into either end: the left is drawn as the right's mirror.","One model of both halves (the seam a groove along each side between the upper half's side face and the lower half's): they come in one box, in one colour, and are never apart on a rifle.","Its section: the rail's head (MIL-STD-1913's, from the ledger) on a neck (the head's lower faces carried on at 45 degrees to the neck's top, the neck upright from there) down to a flat shelf out to the upper half's side faces (1.70 across: assumed, the lower half's top shows as a ledge outside them), the neck hollow over the gas tube up to a web under the rail's slots (its roof assumed); the lower half's side faces at the maker's 1.83; a lower bevel each side down to the bottom flat at the maker's 2.25 (its width read on the bottom's silhouette); flat faces throughout.","Its wall is 0.08 in (assumed: no view looks into an end; set near the maker's installed weight at aluminium's density), each half's inside its own section less the wall, open from end to end.","The rear flanges that go into the delta ring are drawn as a round collar split at the seam each side and notched over the gas tube, from the ring's lip to each half's rear face, inside the ring's skirt and outside the barrel nut's flange (their diameters assumed); the photo shows them as dark as the body, each held by two pins whose heads aren't drawn.","The rail's tongue reaches back over the delta ring to the upper receiver's front face (it reads a few hundredths behind it, inside the readings' ±: drawn bearing on it), a plate level with the rail's top in the head's section, 0.12 in deep (assumed). The rail's slots are the standard's on the pitch from the first's place, the first between the tongue and the first land.","Cut through each side: 9 round holes along the upper side face and a long one at its front, 10 round holes along the lower bevel, 4 M-LOK slots at the standard's size on the lower side face, and two QD sockets on the M-LOK row, all where the camera reads them. The sockets' anti-rotation notches and the fifth socket the maker counts (not seen: perhaps under the bottom) aren't drawn.","Its front: the upper half rounds over at its top front corner (radius assumed); the bottom flat's front part, from where the photo shows its step, is cut up 0.12 in (assumed). The triangle cap stands inside its front end, which reaches 0.16 in over the front sight base's rear; what inside it bears in the cap isn't seen and isn't drawn: it is seated there by its mounting length, the room the rifle holds it in. What of its front then stands in the front sight base's space is cut from its inside with 0.02 in to spare all round the base (its own model, placed at its rear face: base_rear_x), which leaves the rail's front end and the upper half's front following the base's sloped rear leg.","The maker's overall length, 8.5 in, and its photo's 9.04 for the rail's whole length are a conflict kept in the ledger; the photo's is drawn (its carbine length reads its maker's 7 in for the same span, and this one's rail has five slots more)."],"ledger":["midwest-industries-drop-in-mlok-mid.length","midwest-industries-drop-in-mlok-mid.overall_length","midwest-industries-drop-in-mlok-mid.width","midwest-industries-drop-in-mlok-mid.height","midwest-industries-drop-in-mlok-mid.rear_x","midwest-industries-drop-in-mlok-mid.mounting_length"]},"profiles":{},"gaps":[{"what":"How deep its rail's neck runs before the upper half's top (a shelf 0.43 in under the rail's top as read, on one oblique photo, the engraved face under the head taken for the neck's side as on the maker's Combat Rail; read as a shoulder sloping out from the head instead, 17 of the clamps on file stood in it); Aimpoint's PRO stands on that shelf beside the neck as drawn (app/tests/rail-clamps.test.ts), and every other clamp on file clears it","need":"A view along it from either end, or a photo of a clamp on its rail from the side"},{"what":"A level view of either side, the underside (the fifth QD socket, any slots or holes there) and the left side","need":"A seller's or a buyer's photos of an MI-18M from the side, from below and from the left: every place on file is read through one oblique photo"},{"what":"Its section square on, its wall and the upper half's width","need":"An end view with a known size in frame (a photo into either end)"},{"what":"What bears in the cap at its front, and how far its front reaches over the front sight base","need":"A photo of it installed on an A2 front sight base, from the side"},{"what":"The maker's 8.5 in overall length against its photo's 9.04 for the rail's whole length (the upper half's body alone reads 8.45)","need":"The maker's word on what the figure spans, or a seller's own measurement"}]},"midwest-mk2-qd-t2-226":{"id":"midwest-mk2-qd-t2-226","name":"MK2 QD T2 Aimpoint Mount, NV 2.26 in Height","manufacturer":"Midwest Industries","sku":"MI-MK2-QDT2NV-2.26","url":"https://midwestindustriesinc.com/mk2-qd-t2-aimpoint-mount/","category":"optic_mount","description":"A quick-detach mount for Aimpoint Micro footprint red dots at the maker's night vision height (its option \"2.26\\\" Height\", number MI-MK2-QDT2NV-2.26; Primary Arms the same). The maker: \"Available in Low, Lower 1/3 Cowitness, Absolute Cowitness, and NV 2.26” height\", \"Patented QD lever by Elite Defense\", \"Hard Coat Anodized 6061 Aluminum for a lifetime of service\". Primary Arms: \"This is the NV 2.26-inch height, which raises the optic for a heads-up posture and for use with night vision, well above a standard iron sight cowitness.\" The 2.26 in is taken as the axis of a T-2, the dot the mount is named for: the maker names none.","weight":"midwest-mk2-qd-t2-226.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":[0,0,0],"note":"Mount frame: on the rail's top under the middle of the clamp base, +x forward: the cross shaft the lever and the adjustment nut are on is there, in a rail slot (the 1/3 height's left view)."},"deck":{"origin":["{.deck_x}","{.deck_above_rail}",0],"note":"On the deck's top at its middle, where a Micro dot's base is put (D101): the deck over the base as the 1/3 height's photographs have it."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":"={.mount_length} / 2","clamp_front":"={.mount_length} / 2"},"flips":false,"note":"The clamp base's length about its middle, the 1/3 height's (one base in every picture of the four heights). The maker says only \"can be adjusted to fit rails not machined to Mil-Spec tolerances\"; nothing it publishes says where along a rifle's rail it goes."},"deck":{"type":"optic_footprint","role":"deck","anchor":"deck","params":{"pattern":"aimpoint_micro"},"flips":false,"note":"Cut for the Aimpoint Micro footprint: its name (\"MK2 QD T2 Aimpoint Mount\"); Primary Arms' table \"Compatible Model Aimpoint Micro T-1, Aimpoint Micro T-2\", \"Mount Compatibility Aimpoint Micro\" (data/interfaces.yaml, optic_footprint)."}},"materials":{"mount":{"label":"Mount","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized_matte","color":"placeholder-black","sku":"MI-MK2-QDT2NV-2.26","source":"https://midwestindustriesinc.com/mk2-qd-t2-aimpoint-mount/"}},"default":"black","note":"The one colour it is sold in: the maker's page offers a height, no colour (\"Hard Coat Anodized 6061 Aluminum for a lifetime of service\"); Primary Arms' table: \"Color Black\", \"Finish Hardcoat Anodized\". The deck, the web, the base, the QD lever and the 12-sided nut are one matte black in the maker's photographs. A black on sealed anodize is the catalog's stand-in black, not fitted to a photo."},"hardware":{"label":"Lock button, pins and screw","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The lever's lock button, the slotted screw in the adjustment nut's middle and the cross shaft where it crosses the rail: steel, a lighter grey than the anodize in the maker's photographs. No page says what they are: drawn as dark steel."}},"components":{"mount":{"label":"Mount","material":"mount"},"hardware":{"label":"Lock button","material":"hardware"}},"geometry":{"model":"midwest-mk2-qd-t2-226.glb","components":{},"approximations":["No straight view of this height is on file (the maker's one picture of it is a quarter view): its deck plate, its clamp base, its QD lever and nut and everything across the mount are drawn as the 1/3 height's (midwest-mk2-qd-t2-lower-13: its traced outlines and its ledger, with what that part assumes), one base and one deck in the maker's pictures of every height. Its own are the deck's height (the maker's 2.26 in less a T-2's axis over its base) and its web: a straight-sided slab, its length read on its quarter view against the 1/3's in the same pose, with rounds where it meets the deck and the base (their size assumed).","The deck's top is drawn flat where the dot's base sits; its side lips and the square recoil lug, which stand over that plane, aren't drawn (the 1/3's approximations say why). The web's oval panel is drawn as the groove round it on both flanks, read on the right one (the left one is taken to be the same, as the 1/3's two flanks are); the maker's mark in it and the small round hole near the web's top in the quarter view aren't drawn."],"ledger":["midwest-mk2-qd-t2-226.deck_above_rail","midwest-mk2-qd-t2-226.web_length","midwest-mk2-qd-t2-lower-13.deck_length","midwest-mk2-qd-t2-lower-13.deck_width","midwest-mk2-qd-t2-226.mount_length","midwest-mk2-qd-t2-lower-13.clamp_below_rail"]},"profiles":{},"gaps":[{"what":"The dot the maker's 2.26 in is given for","need":"A page of Midwest's that says it: the T-2 is taken, the dot the mount is named for; Police1's 2.26 in for \"an Aimpoint T1 style optic\" was of the older mount"},{"what":"A straight side view of this height","need":"The maker's or a seller's: its deck, base and lever are drawn as the 1/3's, its web's length read on a quarter view (± 0.08 in)"},{"what":"A weight for the MK2 at this height","need":"A page that gives it: its metal as modelled stands for it"},{"what":"The MK2 T2 Aimpoint Mount (cross bolts) at this height","need":"Sold by the maker as a product of its own (MI-MK2-T2NV-2.26; Primary Arms the same): two Torx cross bolts where this has the QD lever. Not in this batch. Its torque: the maker's older sheet (MI-T1-NV) and Primary Arms (\"Midwest specifies 40 inch-pounds on the cross bolts\") say 40 in-lb, its own casting in the maker's photo 35 in-lb (4e0436e89122): a note, nothing here reads it"}]},"midwest-mk2-qd-t2-low":{"id":"midwest-mk2-qd-t2-low","name":"MK2 QD T2 Aimpoint Mount, Low","manufacturer":"Midwest Industries","sku":"MI-MK2-QDT2L","url":"https://midwestindustriesinc.com/mk2-qd-t2-aimpoint-mount/","category":"optic_mount","description":"A quick-detach mount for Aimpoint Micro footprint red dots at the maker's low height (its option \"Low\", number MI-MK2-QDT2L; Primary Arms the same): the deck plate stands on the clamp base with no web between. The maker: \"Available in Low, Lower 1/3 Cowitness, Absolute Cowitness, and NV 2.26” height\", \"Patented QD lever by Elite Defense\", \"Hard Coat Anodized 6061 Aluminum for a lifetime of service\". Primary Arms: \"This is the low height, which keeps the optic close to the rail for a compact, low-profile setup that stays out of the way.\" No page gives its height: it is read on the maker's picture of it, which puts a T-2's axis 1.11 in over the rail.","weight":"midwest-mk2-qd-t2-low.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":[0,0,0],"note":"Mount frame: on the rail's top under the middle of the clamp base, +x forward: the cross shaft the lever and the adjustment nut are on is there, in a rail slot (the 1/3 height's left view)."},"deck":{"origin":["{.deck_x}","{.deck_above_rail}",0],"note":"On the deck's top at its middle, where a Micro dot's base is put (D101): the deck over the base as the 1/3 height's photographs have it."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":"={.mount_length} / 2","clamp_front":"={.mount_length} / 2"},"flips":false,"note":"The clamp base's length about its middle, the 1/3 height's (one base in every picture of the four heights). The maker says only \"can be adjusted to fit rails not machined to Mil-Spec tolerances\"; nothing it publishes says where along a rifle's rail it goes."},"deck":{"type":"optic_footprint","role":"deck","anchor":"deck","params":{"pattern":"aimpoint_micro"},"flips":false,"note":"Cut for the Aimpoint Micro footprint: its name (\"MK2 QD T2 Aimpoint Mount\"); Primary Arms' table \"Compatible Model Aimpoint Micro T-1, Aimpoint Micro T-2\", \"Mount Compatibility Aimpoint Micro\" (data/interfaces.yaml, optic_footprint)."}},"materials":{"mount":{"label":"Mount","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized_matte","color":"placeholder-black","sku":"MI-MK2-QDT2L","source":"https://midwestindustriesinc.com/mk2-qd-t2-aimpoint-mount/"}},"default":"black","note":"The one colour it is sold in: the maker's page offers a height, no colour (\"Hard Coat Anodized 6061 Aluminum for a lifetime of service\"); Primary Arms' table: \"Color Black\", \"Finish Hardcoat Anodized\". The deck, the web, the base, the QD lever and the 12-sided nut are one matte black in the maker's photographs. A black on sealed anodize is the catalog's stand-in black, not fitted to a photo."},"hardware":{"label":"Lock button, pins and screw","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The lever's lock button, the slotted screw in the adjustment nut's middle and the cross shaft where it crosses the rail: steel, a lighter grey than the anodize in the maker's photographs. No page says what they are: drawn as dark steel."}},"components":{"mount":{"label":"Mount","material":"mount"},"hardware":{"label":"Lock button","material":"hardware"}},"geometry":{"model":"midwest-mk2-qd-t2-low.glb","components":{},"approximations":["No straight view of this height is on file (the maker's one picture of it is a quarter view): its deck plate, its clamp base, its QD lever and nut and everything across the mount are drawn as the 1/3 height's (midwest-mk2-qd-t2-lower-13: its traced outlines and its ledger, with what that part assumes), one base and one deck in the maker's pictures of every height. Its own is the deck's height, read on its quarter view: the deck plate is drawn standing on the base's top, as the picture has it, and where the reading and the 1/3's base and plate differ (0.002 in) the plate is let down into the base.","The deck's top is drawn flat where the dot's base sits; its side lips and the square recoil lug, which stand over that plane, aren't drawn (the 1/3's approximations say why)."],"ledger":["midwest-mk2-qd-t2-low.deck_above_rail","midwest-mk2-qd-t2-lower-13.deck_length","midwest-mk2-qd-t2-lower-13.deck_width","midwest-mk2-qd-t2-low.mount_length","midwest-mk2-qd-t2-lower-13.clamp_below_rail"]},"profiles":{},"gaps":[{"what":"The maker's height for this mount, in inches, and the dot it is given for","need":"A page or a drawing of Midwest's: it is read here on a quarter view against the 1/3's, ± 0.06 in"},{"what":"A straight side view of this height","need":"The maker's or a seller's: its deck, base and lever are drawn as the 1/3's"},{"what":"A weight for the MK2 Low","need":"A page that gives it: its metal as modelled stands for it (Primary Arms' 1.7 oz is the older QD Low's, MI-QDT1-L)"},{"what":"The MK2 T2 Aimpoint Mount (cross bolts) at this height","need":"Sold by the maker as a product of its own (MI-MK2-T2L; Primary Arms the same): two Torx cross bolts where this has the QD lever. Not in this batch. Its torque: the maker's older sheet (MI-T1-NV) and Primary Arms (\"Midwest specifies 40 inch-pounds on the cross bolts\") say 40 in-lb, its own casting in the maker's photo 35 in-lb (4e0436e89122): a note, nothing here reads it"}]},"midwest-mk2-qd-t2-lower-13":{"id":"midwest-mk2-qd-t2-lower-13","name":"MK2 QD T2 Aimpoint Mount, Lower 1/3 Cowitness","manufacturer":"Midwest Industries","sku":"MI-MK2-QDT21/3","url":"https://midwestindustriesinc.com/mk2-qd-t2-aimpoint-mount/","category":"optic_mount","description":"A quick-detach mount for Aimpoint Micro footprint red dots at the lower 1/3 co-witness height (the maker's option \"1/3 Cowitness\", number MI-MK2-QDT21/3; Primary Arms MI-MK2-QDT21-3). The maker: \"Patented QD lever by Elite Defense\", \"Fully adjustable QD lever with no tools required - can be adjusted to fit rails not machined to Mil-Spec tolerances\", \"Hard Coat Anodized 6061 Aluminum for a lifetime of service\", \"Available in Low, Lower 1/3 Cowitness, Absolute Cowitness, and NV 2.26” height\", \"Patterns available – RMR, Acro, T2 or Micro dot clones\". Primary Arms: \"This is the lower 1/3 cowitness height, which sets the optic higher so your iron sights appear in the lower third of the optic window.\" No page gives its height in inches: its deck's height is read on the maker's photograph of it with a Micro T-2 on it, which puts a T-2's axis 1.69 in over the rail.","weight":"midwest-mk2-qd-t2-lower-13.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":[0,0,0],"note":"Mount frame: on the rail's top under the middle of the clamp base, +x forward. The cross shaft the lever and the adjustment nut are on is there (the nut's centre within 0.012 in of the base's middle in the left view), in a rail slot."},"deck":{"origin":["{.deck_x}","{.deck_above_rail}",0],"note":"On the deck's top at its middle, where a Micro dot's base is put (D101): the four screw holes and the lug are about the deck's middle."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":"={.mount_length} / 2","clamp_front":"={.mount_length} / 2"},"flips":false,"note":"The clamp base's length about its middle, where the one cross shaft is; the lever's tail reaches further back beside the base, clear of the rail. The maker says only \"can be adjusted to fit rails not machined to Mil-Spec tolerances\"; its instruction sheet: \"Install the mount on your rail and try to shut the lever.\" Nothing it publishes says where along a rifle's rail it goes."},"deck":{"type":"optic_footprint","role":"deck","anchor":"deck","params":{"pattern":"aimpoint_micro"},"flips":false,"note":"Cut for the Aimpoint Micro footprint: its name (\"MK2 QD T2 Aimpoint Mount\"); Primary Arms' table \"Compatible Model Aimpoint Micro T-1, Aimpoint Micro T-2\", \"Mount Compatibility Aimpoint Micro\"; Bud's Gun Shop: \"Designed to fit the Aimpoint T-2 optic footprint\" (data/interfaces.yaml, optic_footprint)."}},"materials":{"mount":{"label":"Mount","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized_matte","color":"placeholder-black","sku":"MI-MK2-QDT21/3","source":"https://midwestindustriesinc.com/mk2-qd-t2-aimpoint-mount/"}},"default":"black","note":"The one colour it is sold in: the maker's page offers a height, no colour (\"Hard Coat Anodized 6061 Aluminum for a lifetime of service\"); Primary Arms' table: \"Color Black\", \"Finish Hardcoat Anodized\". The deck, the web, the base, the QD lever and its jaw plate and the 12-sided nut are one matte black in every photograph of the maker's (the lever and the nut as dark as the body; no bright edge). A black on sealed anodize is the catalog's stand-in black, not fitted to a photo."},"hardware":{"label":"Lock button, pins and screw","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The lever's lock button (\"2. Lock button\", the maker's sheet) and its two hinge pins, and the slotted screw in the adjustment nut's middle: steel, a lighter, smoother grey than the anodize in the maker's photographs (the button in 9aa8e9d3f620, the pins in 165f8d951a1d). No page says what they are: drawn as dark steel."}},"components":{"mount":{"label":"Mount","material":"mount"},"hardware":{"label":"Lock button","material":"hardware"}},"geometry":{"model":"midwest-mk2-qd-t2-lower-13.glb","components":{},"approximations":["The side outline is the maker's straight left photograph (profiles.side), traced and placed by the deck's two ends at the deck's height: the scale is the Micro T-2 the maker photographed on the mount, through the deck's length read in that photograph. Everything across the mount is assumed or read on another product's photograph: the deck's width and its four holes on the cross-bolt MK2's view from below (its deck the same length as this one's within 2%); the base's sides, the web's width, the lever's and the nut's thickness are assumptions (ledger entries marked assumed), no straight view from an end, above or below of this mount being on file.","The deck's top is drawn flat where the dot's base sits (deck_above_rail). Its two side lips, 0.05 in over it in every photograph, and the square recoil lug in its middle, which goes up into a dot's base, aren't drawn: the three Micro dots on file are drawn with bases as wide as their housings, wider than this deck, and anything over the deck's plane would stand inside them. The deck's four screw holes are cut through it.","The rail's top inside the base, which no side view shows, is placed at the clamp's cross shaft (the adjustment nut's centre), 0.018 in under the rail's top as a shaft lying in a rail slot is: the deck's height rests on that (± 0.06 in with the T-2's own figures). The base's channel is the rail's own head in section (MIL-STD-1913's) from the rail's top down to the lower gauge line, plain walls below it; the cross shaft in its slot, the lever's cam and springs, and the jaw plate's working inside aren't drawn.","The web is the side outline across its width with its raised oval panel left standing between two grooves on each flank (the maker's mark on the right one isn't drawn). The QD lever is the right photograph's outline under the base's top (profiles.lever) standing out from the base's right side, its ribs and the knuckle's relief not cut; its lock button and two hinge pins are drawn as steel. The 12-sided adjustment nut stands out of the base's left side round the shaft's axis, between two ribs."],"ledger":["midwest-mk2-qd-t2-lower-13.deck_above_rail","midwest-mk2-qd-t2-lower-13.deck_x","midwest-mk2-qd-t2-lower-13.mount_length","midwest-mk2-qd-t2-lower-13.deck_length","midwest-mk2-qd-t2-lower-13.deck_width","midwest-mk2-qd-t2-lower-13.clamp_below_rail"]},"profiles":{"side":{"plane":"xy","origin":"on the rail's top under the middle of the clamp base: the part frame","offset":{},"points":[[-1.005,1.138],[-1.005,1.009],[-0.923,0.929],[-0.618,0.929],[-0.572,0.915],[-0.507,0.878],[-0.47,0.841],[-0.43,0.774],[-0.414,0.72],[-0.414,0.517],[-0.425,0.466],[-0.454,0.409],[-0.526,0.337],[-0.714,0.336],[-0.714,0.225],[-0.708,0.22],[-0.714,0.217],[-0.714,-0.11],[-0.705,-0.115],[-0.703,-0.185],[-0.637,-0.257],[-0.62,-0.265],[-0.08,-0.265],[-0.072,-0.273],[0.085,-0.273],[0.101,-0.262],[0.619,-0.262],[0.648,-0.245],[0.702,-0.177],[0.704,0.169],[0.615,0.258],[0.613,0.323],[0.607,0.339],[0.592,0.354],[0.563,0.359],[0.449,0.359],[0.41,0.406],[0.386,0.463],[0.372,0.533],[0.372,0.695],[0.38,0.738],[0.407,0.801],[0.445,0.852],[0.492,0.891],[0.552,0.923],[0.565,0.929],[0.903,0.929],[0.982,1.003],[0.985,1.022],[0.985,1.135],[0.968,1.153],[-0.993,1.153]],"scaleRefs":["midwest-mk2-qd-t2-lower-13.deck_x","midwest-mk2-qd-t2-lower-13.deck_length","midwest-mk2-qd-t2-lower-13.deck_above_rail","midwest-mk2-qd-t2-lower-13.deck_lip_height"],"inputs":{"midwest-mk2-qd-t2-lower-13.deck_above_rail":1.1,"midwest-mk2-qd-t2-lower-13.deck_length":1.985,"midwest-mk2-qd-t2-lower-13.deck_lip_height":0.049,"midwest-mk2-qd-t2-lower-13.deck_x":-0.01},"tolerance":0.004,"photo":"references/midwest-mk2-qd-t2-lower-13 723bb889a675 (MI-MK2-QDT213-l: the mount alone, straight left side on white, 1280 x 1280, muzzle to the left)","method":"luminance < 235, 1 boxes excluded, largest piece, holes filled; frame from the reviewed holes deck_front, deck_rear (370.3 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.004 in with the extremes kept: 52 points (IoU 0.998 with the full outline); checks: −y_min 0.273 ± 0.004 in vs midwest-mk2-qd-t2-lower-13.clamp_below_rail 0.277 ± 0.04 (provisional): agrees (tools/trace.py)","via":"harvest","note":"The mount's left side turned to face +x, the lever's tail behind the base cut away: the deck with its chamfered lower edges at both ends, the waisted web, the base block with its chamfered upper corners. The lips' top is the deck's top here: the model lowers it to the deck's top where the dot's base sits (deck_lip_height)."},"lever":{"plane":"xy","origin":"on the rail's top under the middle of the clamp base: the part frame","offset":{},"points":[[-1.302,0.103],[-1.302,0.003],[-1.297,-0.121],[-1.277,-0.168],[-1.24,-0.211],[-1.157,-0.26],[-1.11,-0.269],[-1.019,-0.263],[-0.707,-0.263],[-0.708,-0.328],[-0.693,-0.338],[-0.666,-0.343],[-0.169,-0.338],[-0.136,-0.329],[-0.114,-0.34],[-0.02,-0.343],[0.107,-0.338],[0.12,-0.331],[0.124,-0.318],[0.381,-0.335],[0.521,-0.335],[0.626,-0.329],[0.69,-0.318],[0.708,-0.306],[0.708,-0.198],[0.702,-0.173],[0.708,-0.162],[0.708,-0.066],[0.702,0.166],[0.695,0.234],[-1.16,0.234],[-1.201,0.214],[-1.248,0.181],[-1.288,0.136]],"scaleRefs":["midwest-mk2-qd-t2-lower-13.deck_x","midwest-mk2-qd-t2-lower-13.deck_length","midwest-mk2-qd-t2-lower-13.deck_above_rail","midwest-mk2-qd-t2-lower-13.deck_lip_height"],"inputs":{"midwest-mk2-qd-t2-lower-13.deck_above_rail":1.1,"midwest-mk2-qd-t2-lower-13.deck_length":1.985,"midwest-mk2-qd-t2-lower-13.deck_lip_height":0.049,"midwest-mk2-qd-t2-lower-13.deck_x":-0.01},"tolerance":0.004,"photo":"references/midwest-mk2-qd-t2-lower-13 caa89ca71b96 (MI-MK2-QDT213-r: the mount alone, straight right side on white, 1280 x 1280, muzzle to the right)","method":"luminance < 235, inside [200, 703, 1000, 930], largest piece, holes filled; frame from the reviewed holes deck_front, deck_rear (362.2 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.004 in with the extremes kept: 34 points (IoU 0.996 with the full outline) (tools/trace.py)","via":"harvest","note":"The lever side below the base's top (rows 703 down): the lever lying closed along the base with its tail 0.5 in behind it, its knuckle, the jaw plate at its front and the jaw's foot under it. Drawn standing out from the base's right side (lever_thickness)."}},"gaps":[{"what":"The maker's height for this mount, in inches, and the dot it is given for","need":"A page or a drawing of Midwest's with the 1/3 height's figure (an axis over the rail for a named dot, or the deck's own height): it is read here on the maker's photograph of it with a T-2 on it, ± 0.06 in"},{"what":"A view of this mount from an end, from above or from below","need":"The maker's or a seller's straight photograph across the mount: the deck's width, the base's sides, the web's width and the lever's thickness are read on the cross-bolt MK2's view from below or assumed"},{"what":"The maker's weight for the MK2","need":"A page of Midwest's with it: the one figure on file is Bud's Gun Shop's 3.6 ounces, a seller's"},{"what":"The MK2 T2 Aimpoint Mount (cross bolts) at this height","need":"Sold by the maker as a product of its own (MI-MK2-T21/3; Primary Arms MI-MK2-T21-3): two Torx cross bolts in steel clamps where this has the QD lever. Not in this batch. Its torque: the maker's older sheet (MI-T1-NV) and Primary Arms (\"Midwest specifies 40 inch-pounds on the cross bolts\") say 40 in-lb, its own casting in the maker's photo 35 in-lb (4e0436e89122): a note, nothing here reads it"}]},"nordic-22rb-upper":{"id":"nordic-22rb-upper","name":"22RB .22 LR upper, 16\"","manufacturer":"Nordic Components","sku":"22RB-UPPER-16-KIT","category":"upper","description":"Dedicated .22 LR upper with a 16\" stainless barrel threaded 1/2-28, slick-side receiver, full-length top rail and a receiver-height M-LOK handguard. Black Teflon finish. Ships with a thread protector (the muzzle slot's nordic-thread-protector) and a 10-round Black Dog magazine.","weight":"nordic-22rb-upper.weight","barrelLength":"nordic-22rb-upper.barrel_length","cartridge":{"takes":[".22 LR"],"stated":"Nordic Components' 22RB Dedicated 22 Upper converts your AR15-pattern rifle into a dedicated 22 rimfire just by changing upper receivers. (the page's category: NC 22LR UPPERS & CHARGE HANDLES > 22RB (Dedicated .22 Upper))","source":"https://nordiccomp.com/categories/nc-22rb-upper/ (Nordic's page, as cached: harvest.quote)"},"mass":{"note":"Only the complete upper's weight is published, and the one weighed was weighed whole. Its barrel is taken as a plain stainless tube at the diameter it shows ahead of the handguard, for the 16 in Nordic gives (what it measures under the handguard isn't sourced); its handguard as drawn, in aluminium (40.7 mm across the flats, bored 35.6 mm, M-LOK slots cut), with its rail's teeth, which are drawn apart from it; the receiver takes the rest, with the stainless bolt, the charging handle and the barrel's fittings in it.","lumps":{"barrel":{"tube":{"from":["{.muzzle_shoulder_x} + {.muzzle_thread_length} - {.barrel_length}","{.bore_axis_above_pin}",0],"to":["{.muzzle_shoulder_x} + {.muzzle_thread_length}","{.bore_axis_above_pin}",0],"od":"{.barrel_od}","bore":"{.bore_d}"},"density":"std.density.stainless_416"},"handguard":{"component":"handguard","density":"std.density.aluminium"},"handguard rail teeth":{"solid":{"volume":"({.rail_front_x} - {.handguard_rail_rear_x}) * {std.picatinny.top_width} * {std.picatinny.slot_depth} * (1 - {std.picatinny.slot_width} / {std.picatinny.slot_pitch})","at":["({.rail_front_x} + {.handguard_rail_rear_x}) / 2","{.handguard_rail_top_above_pin} - {std.picatinny.slot_depth} / 2",0]},"density":"std.density.aluminium","note":"The handguard rail's teeth above the slot floors, by the standard's width, depth and pitch: the handguard's model stops at the floors and the rail drawn on it reaches into it, so neither gives the teeth alone."},"receiver":{"component":"receiver","rest":true}}},"occupies":["barrel","handguard","gas_block","gas_tube","bolt_carrier_group","charging_handle"],"integral":[],"brings":[],"without":{"slots":["buffer","buffer_spring"],"says":"Nordic Components, of the 22RB: \"The buffer and spring assembly should be removed from the lower receiver prior to use. While the 22RB Dedicated Upper will function with the buffer assembly installed, you may experience failures to feed due to bolt bounce.\"","source":"https://nordiccomp.com/wp-content/uploads/2021/06/22RB-Manual-2021.pdf"},"seats":{},"requires":[],"anchors":{"pins":{"origin":[0,0,0]},"top_rail":{"origin":["{.rail_slot0_x}","{.rail_top_above_pin}",0]},"muzzle":{"origin":["{.muzzle_shoulder_x}","{.bore_axis_above_pin}",0],"note":"The barrel's shoulder behind the muzzle thread, on the bore axis: a muzzle device seats against it."},"mlok":{"origin":["{.mlok_slot_front_x} - ({.mlok_slots_per_face} - 1) * {std.mlok.slot_pitch}","{.handguard_center_y}",0],"note":"On the handguard's axis (the octagon's centre) at the rearmost M-LOK slot's centre (index 0), +x toward the muzzle; the faces are angles about this axis (M10)."}},"interfaces":{"receiver_pins":{"type":"ar15.upper_lower","role":"upper","anchor":"pins","params":{"pin_spacing":"={std.ar15.pin_spacing}"},"flips":false},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}","seam":"={.receiver_rail_front_x} - {.rail_slot0_x}","seam_step":"={.handguard_rail_step}","seam_parts":"the receiver's rail and the handguard's","seam_behind":"receiver","seam_ahead":"handguard"},"flips":false,"note":"One run of 49 slots over two parts: the receiver's rail ends with the tooth between slots 14 and 15 (receiver_rail_front_x, the seam) and the handguard's begins there with slot 15, on the same pitch and 0.008 in lower (seam_step: what is mounted past the seam sits on the handguard's rail)."},"muzzle":{"type":"muzzle_thread","role":"barrel","anchor":"muzzle","params":{"thread":"1/2-28","thread_length":"={.muzzle_thread_length}"},"flips":false},"mlok":{"type":"mlok","role":"slots","anchor":"mlok","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_slots_per_face}","interval":"={std.mlok.interval}","face_distance":"={.handguard_width} / 2","bore":"={.handguard_id}","reach_inside":"={.handguard_width} / 2 - {.barrel_od} / 2"},"faces":{"right":{"angle":90,"note":"the rifle's right side (+z)"},"right_lower":{"angle":135},"bottom":{"angle":180},"left_lower":{"angle":-135},"left":{"angle":-90},"left_upper":{"angle":-45},"right_upper":{"angle":45}},"flips":false,"note":"Angles about the handguard's axis from +y (0 would be the top, where the rail is; 90 the right side). The slots' x positions are the same on every face (the side photo shows the two visible rows aligned)."}},"materials":{"receiver":{"label":"Receiver, rail and handguard","finish":"cerakote","recolorable":true,"color":"placeholder-black","sheen":"matte","note":"Black Teflon (OpticsPlanet listing title for this SKU; Nordic's page names no finish and offers no colour to choose: sold in black only). Sprayed-coating finish class; a flat, even black with a fine grain on the user's own (74a0161414d1, fc6a01b62b5a), the same on the receiver, its rail and the handguard. Not fitted to a photo: Nordic's two views of it read #5c5a5f (2b348f6a5149, lit) and #222223 (24d592636074) on the same flat, and the user's own #3e3e3e to #6a6a67 by the facet: a black whose reading is the light's. The white marks (Nordic's, the M-LOK mark) aren't pieces. Black too, and drawn in this slot since 2026-10-13: the handguard's clamp block and its two socket-head screws (e421a9af0aa7, 74a0161414d1; Nordic's own right view, 24d592636074). The screws are steel and the block the handguard's own metal: one black in every photo, so one slot; recoloured, the screws take the receiver's colour with it."},"barrel":{"label":"Barrel","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"\"Stainless steel barrel and bolt\" (Nordic, https://nordiccomp.com/categories/nc-22rb-upper/): turned bright, bare, as Nordic's photos (c280084b0a6e) and the user's own (14dc07bfde38) have it ahead of the handguard."},"bolt":{"label":"Bolt (visible through the ejection port)","finish":"steel","recolorable":false,"color":"stainless-natural","note":"Stainless, as Nordic says of it, and bead-blasted: the user's close photo of the port (e421a9af0aa7) has its face flat and matte where the barrel is turned bright. `steel` is the matte metal among the finishes on file (roughness 0.55) and `stainless` the brushed, bright one (0.18): the class is chosen for how the surface answers light, the colour is stainless's own."},"extractor":{"label":"Extractor (on the bolt","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The dark bar along the bolt's side in the user's close photo of the port (e421a9af0aa7): darker steel than the bolt; its colour isn't sampled."},"charging_handle":{"label":"Charging handle and latch","finish":"anodized","recolorable":false,"color":"placeholder-black","note":"The T, its plate and the latch are one black on the user's own (fc6a01b62b5a, 5893d878a7aa, c8a014aa1043), a little smoother than the receiver's coat; Nordic states no finish for it. The latch's pivot pin is a bright steel dot in the T's end (fc6a01b62b5a) and isn't drawn; nor is the bolt assembly's bare steel rear plate behind the receiver."}},"components":{"receiver":{"label":"Upper receiver","material":"receiver"},"handguard":{"label":"M-LOK handguard","material":"receiver"},"barrel":{"label":"Barrel","material":"barrel"},"bolt":{"label":"Bolt","material":"bolt"},"charging_handle":{"label":"Charging handle","material":"charging_handle"}},"geometry":{"components":{"handguard":"nordic-22rb-upper.handguard.glb","receiver":"nordic-22rb-upper.receiver.glb","barrel":"nordic-22rb-upper.barrel.glb"},"approximations":["The handguard's clamp (2026-10-13) is the block under its rear end as the user's own upper has it from the right, from below and close: a flat-faced pad 1.06 in across, its flat underside 0.19 in under the handguard with its four corners cut back, a ramp behind and a ramp ahead, two side faces square to the rifle, slit along the middle from the seam to 0.07 in ahead of the block; two socket-head screws across it, their heads in counterbores on the right face and the threaded holes they reach open on the left. Assumed, since no view gives a depth: the counterbores four fifths of a head's diameter deep, the heads a tenth of their diameter under the face, the sockets three fifths as deep as they are across, the threaded holes open one and a half diameters in and plain (no thread drawn); the slit a groove with its floor 0.02 in short of the bore (it is black in every photo: cut through, it would show the bright barrel). Its ramps and facets are planes where the photos have their meetings blended, and its edges are broken as the handguard's are. The screws are in the receiver's material slot (black, as the block).","The blind panel behind the short slot of the rows on the handguard's two sides and two upper diagonals (2026-10-13) is a pocket of the short slot's own outline, 0.31 in behind it, as Nordic's two side views and the user's close one have it. Assumed: that it is milled in (a side view says where a panel is and not which way it goes) and as deep as the engraved grooves (0.015 in). The three lower faces have none: the clamp is there."],"ledger":["nordic-22rb-upper.handguard_id","nordic-22rb-upper.handguard_center_y","nordic-22rb-upper.mlok_slot_front_x","nordic-22rb-upper.mlok_slots_per_face","std.mlok.slot_length","std.mlok.slot_width","std.mlok.slot_pitch","nordic-22rb-upper.barrel_length","nordic-22rb-upper.rail_top_above_pin","nordic-22rb-upper.receiver_height_with_rail","nordic-22rb-upper.handguard_height","nordic-22rb-upper.muzzle_shoulder_x","nordic-22rb-upper.latch_to_muzzle","nordic-22rb-upper.muzzle_ahead_of_pin","nordic-22rb-upper.barrel_od","nordic-22rb-upper.bore_d","nordic-22rb-upper.muzzle_thread_length","nordic-22rb-upper.muzzle_thread_major_d","nordic-22rb-upper.muzzle_thread_minor_d","nordic-22rb-upper.muzzle_thread_pitch","nordic-22rb-upper.muzzle_thread_start","nordic-22rb-upper.muzzle_thread_end","nordic-22rb-upper.muzzle_relief_d","nordic-22rb-upper.muzzle_pilot_d","nordic-22rb-upper.handguard_length"]},"profiles":{"side":{"plane":"xy","origin":"the takedown lug hole (the rifle frame origin: the upper's lugs sit on the lower's pins)","offset":{},"points":[[-0.86,1.592],[-0.673,1.541],[-0.708,1.102],[-0.694,0.858],[-0.578,0.528],[-0.489,0.504],[-0.272,0.327],[-0.253,-0.188],[-0.211,-0.222],[0.069,-0.227],[0.234,-0.197],[0.24,0.168],[0.273,0.219],[0.358,0.218],[0.385,0.18],[0.517,0.215],[0.648,0.213],[0.685,0.184],[0.798,0.229],[1.088,0.243],[5.954,0.235],[6.038,0.224],[6.047,0.168],[6.094,0.214],[6.141,0.213],[6.173,0.179],[6.196,-0.111],[6.312,-0.202],[6.443,-0.214],[6.579,-0.146],[6.628,-0.062],[6.62,0.031],[6.653,0.064],[6.84,0.032],[7.081,-0.112],[7.577,-0.111],[7.604,-0.149],[7.642,-0.122],[7.848,-0.106],[7.941,-0.127],[8.14,0.01],[8.347,0.072],[15.207,0.049],[20.135,0.068],[20.135,1.958],[20.049,1.96],[20.009,2.068],[19.977,2.083],[19.817,2.076],[19.713,1.965],[19.634,1.99],[19.612,2.089],[19.443,2.082],[19.363,2.042],[19.32,1.963],[19.231,1.997],[19.209,2.086],[19.041,2.08],[18.97,2.039],[18.936,1.969],[18.861,1.971],[18.83,2.06],[18.788,2.084],[18.629,2.077],[18.543,1.967],[18.468,1.968],[18.423,2.081],[18.255,2.084],[18.184,2.043],[18.15,1.964],[18.061,1.989],[18.039,2.078],[17.871,2.081],[17.8,2.04],[17.766,1.961],[17.691,1.962],[17.646,2.085],[17.469,2.088],[17.407,2.047],[17.373,1.968],[17.298,1.969],[17.244,2.082],[17.076,2.085],[16.961,1.966],[16.896,1.967],[16.864,2],[16.86,2.089],[16.673,2.083],[16.596,1.972],[16.503,1.973],[16.471,2.007],[16.467,2.086],[16.308,2.089],[16.218,2.03],[16.227,1.992],[16.194,1.96],[16.11,1.971],[16.065,2.084],[15.896,2.087],[15.81,1.966],[15.754,1.967],[15.684,2.001],[15.681,2.081],[15.532,2.093],[15.461,2.052],[15.417,1.964],[15.314,1.975],[15.279,2.088],[15.148,2.09],[15.077,2.058],[15.024,1.961],[14.921,1.972],[14.886,2.085],[14.708,2.088],[14.65,1.967],[14.537,1.969],[14.493,2.082],[14.315,2.086],[14.281,1.997],[14.219,1.965],[14.144,1.967],[14.112,2],[14.109,2.089],[13.941,2.092],[13.864,1.972],[13.742,1.974],[13.697,2.087],[13.557,2.089],[13.514,2.066],[13.48,1.969],[13.349,1.971],[13.314,2.093],[13.211,2.095],[13.145,2.087],[13.068,1.966],[12.965,1.968],[12.911,2.091],[12.743,2.084],[12.694,1.973],[12.563,1.975],[12.527,2.088],[12.368,2.091],[12.335,2.068],[12.334,2.002],[12.263,1.961],[12.16,1.972],[12.139,2.08],[12.078,2.096],[11.966,2.088],[11.941,2.009],[11.87,1.968],[11.777,1.979],[11.732,2.092],[11.582,2.095],[11.524,1.974],[11.374,1.977],[11.348,2.089],[11.189,2.092],[11.122,1.971],[10.991,1.974],[10.946,2.087],[10.787,2.099],[10.771,2.001],[10.719,1.969],[10.598,1.971],[10.553,2.093],[10.394,2.096],[10.354,1.975],[10.223,1.968],[10.172,1.992],[10.169,2.091],[10.01,2.093],[9.961,1.982],[9.84,1.975],[9.779,1.999],[9.767,2.097],[9.655,2.099],[9.603,2.086],[9.568,1.979],[9.493,1.971],[9.409,1.982],[9.378,2.081],[9.346,2.095],[9.205,2.088],[9.199,2.009],[9.119,1.978],[9.016,1.979],[8.981,2.092],[8.822,2.095],[8.806,2.006],[8.763,1.974],[8.623,1.977],[8.588,2.09],[8.428,2.092],[8.413,2.004],[8.323,1.972],[8.23,1.983],[8.195,2.096],[8.036,2.099],[7.987,1.978],[7.865,1.98],[7.814,2.004],[7.792,2.094],[7.633,2.106],[7.594,1.994],[7.453,1.978],[7.421,2.011],[7.422,2.077],[7.352,2.101],[7.24,2.094],[7.191,1.982],[7.098,1.975],[7.037,1.999],[7.006,2.098],[6.847,2.1],[6.831,2.012],[6.789,1.98],[6.658,1.982],[6.636,2.062],[6.585,2.105],[6.445,2.098],[6.429,2.009],[6.358,1.978],[6.255,1.98],[6.211,2.093],[6.052,2.105],[6.036,2.016],[5.946,1.975],[5.872,1.977],[5.808,2.099],[5.64,2.102],[5.61,1.991],[5.497,1.974],[5.437,2.008],[5.424,2.097],[5.331,2.108],[5.266,2.109],[5.241,2.011],[5.198,1.979],[5.076,1.981],[5.013,2.104],[4.854,2.106],[4.814,1.985],[4.711,1.978],[4.66,2.002],[4.629,2.101],[4.461,2.104],[4.412,1.983],[4.309,1.985],[4.236,2.098],[4.068,2.101],[4.052,2.012],[3.972,1.972],[3.916,1.982],[3.834,2.105],[3.712,2.107],[3.651,2.094],[3.65,2.01],[3.607,1.978],[3.523,1.989],[3.501,2.05],[3.422,2.103],[3.282,2.105],[3.233,1.994],[3.13,1.977],[3.088,2.01],[3.098,2.047],[3.01,2.11],[2.879,2.103],[2.864,2.014],[2.821,1.982],[2.727,1.983],[2.701,2.059],[2.58,2.108],[2.477,2.1],[2.461,2.011],[2.381,1.98],[2.325,1.981],[2.302,2.005],[2.321,2.051],[2.252,2.104],[2.074,2.098],[2.068,2.018],[1.96,1.978],[1.914,2.063],[1.831,2.102],[1.691,2.104],[1.666,2.016],[1.623,1.984],[1.548,1.985],[1.526,2.055],[1.502,2.042],[1.466,2.099],[1.297,2.101],[1.263,2.013],[1.202,1.972],[1.164,1.973],[1.11,2.067],[0.998,2.107],[0.905,2.108],[0.861,2.011],[0.799,1.979],[0.753,1.98],[0.73,2.05],[0.652,2.103],[-0.359,2.102],[-0.528,2.095],[-0.631,2.05],[-0.846,2.063]],"scaleRefs":["std.ar15.pin_spacing","nordic-22rb-upper.rail_slot0_x","nordic-22rb-upper.rail_top_above_pin","std.picatinny.slot_depth","nordic-22rb-upper.rail_last_slot_x","nordic-22rb-upper.handguard_rail_top_above_pin"],"inputs":{"nordic-22rb-upper.handguard_front_x":20.135,"nordic-22rb-upper.handguard_rail_top_above_pin":2.0824,"nordic-22rb-upper.rail_last_slot_x":19.693,"nordic-22rb-upper.rail_slot0_x":0.795,"nordic-22rb-upper.rail_top_above_pin":2.09,"nordic-22rb-upper.rear_behind_pin":0.86,"std.ar15.pin_spacing":6.375,"std.picatinny.slot_depth":0.118},"tolerance":0.02,"photo":"references/nordic-22rb-upper d633f1bf49ff (the user's own 22RB lying on its left side on tile, its right side square on from 5 to 7 ft, a tape beside it)","method":"luminance < 70, 1 polygons excluded, closing ×2, largest piece, holes filled; frame from the reviewed holes takedown, pivot, slot0, slot48 (106.9 px/in, rms 0.015 in over 4 points); origin at the photo's frame; clipped to x min -{.rear_behind_pin} = -0.86, x max {.handguard_front_x} = 20.135; Douglas-Peucker at 0.02 in with the extremes kept: 309 points (IoU 0.994 with the full outline); checks: top (tooth tops: the edge's max over 0.4 in windows) along x [0.5, 5.5] 2.106 ± 0.028 in vs nordic-22rb-upper.rail_top_above_pin 2.09 ± 0.015 (conflict): agrees; bottom (median) along x [1, 5.5] 0.233 ± 0.028 in vs bad-workhorse-lower.deck_above_pin 0.254 ± 0.009 (corroborated): agrees; height (tooth tops, max over 0.4 in windows) along x [9, 18.5] 2.029 ± 0.028 in vs nordic-22rb-upper.handguard_height 2.0059 ± 0.045 (conflict): agrees; top (tooth tops: the edge's max over 0.4 in windows) along x [9, 18.5] 2.092 ± 0.028 in vs nordic-22rb-upper.rail_top_above_pin 2.09 ± 0.015 (conflict): agrees (tools/trace.py)","via":"user","note":"Receiver, handguard and top rail in one outline (M-LOK slots filled, the rail's slots kept); the barrel and thread protector are the builder's cylinder from the handguard front."},"front":{"plane":"zy","origin":"the section's bottom flat, centred on the bore's vertical; offset up to the handguard's underside","offset":{"y":"handguard_bottom_y"},"points":[[-0.801,0.75],[-0.797,0.513],[-0.77,0.446],[-0.376,0.048],[-0.279,0.005],[0,0.001],[0.037,0],[0.261,0.003],[0.376,0.049],[0.759,0.429],[0.799,0.529],[0.801,0.807],[0.796,1.105],[0.774,1.162],[0.308,1.638],[0.31,1.782],[0.34,1.83],[0.398,1.878],[0.409,1.924],[0.314,2.009],[-0.221,2.013],[-0.328,2.007],[-0.411,1.921],[-0.388,1.855],[-0.36,1.85],[-0.378,1.845],[-0.374,1.821],[-0.344,1.831],[-0.316,1.786],[-0.306,1.65],[-0.317,1.619],[-0.456,1.488],[-0.769,1.155],[-0.798,1.076]],"scaleRefs":["nordic-22rb-upper.handguard_width"],"inputs":{"nordic-22rb-upper.handguard_width":1.602},"tolerance":0.008,"photo":"references/nordic-22rb-upper 2cd733a9d284 (the user's own 22RB, the muzzle end straight on (the upper upside down, the rail at the bottom), a tape across above)","method":"luminance < 90, inside [0, 560, 2576, 1932], opening 9 px ×1, closing ×2, largest piece, holes filled; rotated +181.3° as declared; scale from nordic-22rb-upper.handguard_width = 1.602 in (x-extent 922 px → 575.8 px/in); origin at x center, y min of the outline; Douglas-Peucker at 0.008 in with the extremes kept: 34 points (IoU 0.994 with the full outline); checks: height 2.013 ± 0.007 in vs nordic-22rb-upper.handguard_height 2.0059 ± 0.045 (conflict): agrees (tools/trace.py)","via":"user","note":"Seen from the muzzle, so its right is the rifle's left; the section is symmetric within 0.01 in. The rail's end is 0.15 in behind the handguard's front, so the rail head reads 0.4% small: the app draws the rail to MIL-STD-1913 and uses this section up to the rail's slot floors."},"handle":{"plane":"xz","origin":"the rifle's frame, the handle home: the T's two ends at the T's width either side of the centre plane, at the middle of its depth ahead of its rear face (rear_behind_pin); +x toward the muzzle, +z to the rifle's right","offset":{},"points":[[-0.869,0.681],[-0.865,0.673],[-0.868,0.573],[-0.863,0.567],[-0.861,0.439],[-0.856,-0.747],[-0.849,-0.818],[-0.833,-0.867],[-0.807,-0.912],[-0.771,-0.952],[-0.738,-0.977],[-0.696,-0.998],[-0.641,-1.013],[-0.569,-1.019],[-0.529,-1.014],[-0.509,-1.048],[-0.489,-1.063],[-0.439,-1.072],[-0.196,-1.04],[-0.142,-1.016],[-0.111,-0.981],[-0.091,-0.931],[-0.096,-0.876],[-0.104,-0.858],[-0.136,-0.85],[-0.136,-0.837],[-0.123,-0.819],[-0.138,-0.785],[-0.166,-0.781],[-0.173,-0.774],[-0.158,-0.747],[-0.169,-0.715],[-0.176,-0.708],[-0.191,-0.71],[-0.206,-0.701],[-0.18,-0.652],[-0.176,-0.611],[-0.163,-0.571],[-0.134,-0.527],[-0.11,-0.505],[-0.08,-0.485],[-0.042,-0.471],[0.054,-0.454],[0.081,-0.456],[0.114,-0.446],[0.334,-0.421],[0.419,-0.406],[0.441,-0.393],[0.454,-0.371],[0.446,-0.294],[0.437,-0.282],[0.355,-0.22],[0.351,-0.216],[0.357,-0.211],[1.064,-0.21],[1.072,0.197],[0.473,0.195],[0.085,0.201],[0.08,0.216],[0.079,0.313],[0.07,0.319],[-0.04,0.332],[-0.132,0.362],[-0.207,0.409],[-0.283,0.492],[-0.316,0.547],[-0.332,0.59],[-0.339,0.664],[-0.334,0.685],[-0.341,0.696],[-0.344,0.783],[-0.354,0.833],[-0.385,0.897],[-0.415,0.934],[-0.453,0.97],[-0.478,0.981],[-0.707,0.985],[-0.739,0.97],[-0.783,0.93],[-0.81,0.889],[-0.818,0.886],[-0.815,0.881],[-0.826,0.875],[-0.823,0.866],[-0.866,0.767],[-0.861,0.756]],"features":{"latch":[[[0.347,-0.202],[0.262,-0.218],[0.251,-0.29],[0.222,-0.311],[0.188,-0.322],[0.151,-0.313],[0.075,-0.274],[0.006,-0.328],[-0.063,-0.347],[-0.136,-0.377],[-0.207,-0.426],[-0.276,-0.51],[-0.32,-0.604],[-0.334,-0.671],[-0.351,-0.742],[-0.362,-0.808],[-0.39,-0.869],[-0.432,-0.92],[-0.483,-0.954],[-0.522,-0.972],[-0.524,-1.065],[-0.439,-1.068],[-0.319,-1.055],[-0.201,-1.044],[-0.14,-1.015],[-0.108,-0.965],[-0.094,-0.914],[-0.095,-0.871],[-0.14,-0.847],[-0.129,-0.811],[-0.174,-0.777],[-0.16,-0.738],[-0.207,-0.699],[-0.182,-0.649],[-0.173,-0.589],[-0.139,-0.522],[-0.08,-0.481],[-0.003,-0.465],[0.118,-0.445],[0.288,-0.423],[0.433,-0.396],[0.453,-0.354],[0.436,-0.281]]]},"scaleRefs":["nordic-22rb-upper.charging_handle_t_depth","nordic-22rb-upper.rear_behind_pin","nordic-22rb-upper.charging_handle_t_width"],"inputs":{"nordic-22rb-upper.charging_handle_t_depth":0.496,"nordic-22rb-upper.charging_handle_t_width":1.97,"nordic-22rb-upper.rear_behind_pin":0.86},"tolerance":0.004,"photo":"references/nordic-22rb-upper c8a014aa1043 (the user's own 22RB's charging handle out of the upper, lying top up on a tile floor, from above)","method":"luminance < 135, inside [0, 844, 1350, 2576], closing ×2, largest piece, holes filled; frame from the reviewed holes right_end, left_end (634.9 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.004 in with the extremes kept: 86 points (IoU 0.994 with the full outline); features through the same placement (latch: The latch as it shows from above, the handle out of the upper: its tooth turned in toward the shaft, its arm, its pad with three grooves across its front, the lobe that stands out past the T's left end. Its inner side is the plate's edge and then the T's own outline, which it goes under.) (tools/trace.py)","via":"user","note":"The charging handle from above, in the rifle's frame with the handle home: the T, the plate flared out to it, the shaft (cut by the photo's edge), and on its left the latch. The model takes the plate from the outline's right half (the latch covers the left) and the latch from its feature."}},"gaps":[{"what":"The muzzle's crown: the user's face-on photo (2cd733a9d284) has a ring 0.36 in across round the bore, a recess whose depth no view on file gives; the face is drawn flat, and the bore as one plain hole (its lands and grooves aren't told apart)","need":"The bare muzzle from a quarter ahead (45 degrees off the bore's line), close, the protector off: the recess's far wall then shows beside its near one"},{"what":"The muzzle thread's form and hand: it is a helix, a plain V between the Army drawing's roots and crests without the flats of its form, right-hand by its designation alone (the bare photo's lit flank changes side across the barrel, and the lines' lean isn't read); how long its run-out and its start are; the small break on the shoulder's rim and the face's rim isn't drawn","need":"The bare muzzle from the side, closer than c0e654135597 and lit from the camera's side: the lines' lean, the last turn into the relief, the rims' breaks"},{"what":"The receiver's lower corners ahead of its rear chamfers, on the user's own upper: the 0.134 in drawn is from Nordic's photo down a receiver from its rear, where the user's is chamfered 0.23 (receiver_rear_chamfer_w)","need":"The underside from 8 ft or more, zoomed, with the light raking across it: the corner's width from 3 in ahead of the takedown pin to the handguard"},{"what":"How far the bolt's flat face stands behind the ejection port's opening: the model stands the flat on the bore's round where the photos have its lower edge. The photos of 2026-10-05 from above the rail and from above and to the right have it close under the opening's upper lip, but each is one steep view from close and no two fix a camera","need":"The port from 8 ft or more, zoomed, twice: once from the front right quarter and once from above the rail looking down into it, the rail's teeth in both frames"},{"what":"How deep the bolt's details go: the break along its face's upper edge and down its ends (drawn at 45 degrees), the screw's seat (half the break), the slot the extractor lies in (half the round), the extractor's bar (two thirds of the slot high) and its spring's wire (a third of the pitch). Their places and sizes across the face are read on the square photo of the port (26b2fef5a5a3) and drawn since 2026-10-12; the band under the face is still the round it was taken for","need":"The same two photos as the face's depth: the port from 8 ft or more, zoomed, from the front right quarter and from above the rail"},{"what":"What of the charging handle's latch is under the T and the plate (drawn filling the slot), and how deep the receiver is cut for the latch's arm and for its tooth (cut to the latch and a clearance)","need":"The handle out of the upper from below, and the receiver's rear from above and from its left with the handle out: the room it leaves"},{"what":"How deep the handguard's clamp and panels go: the counterbores the two screw heads sit in and how far under the face the heads stand, the sockets, how far in the threaded holes on the left are open, and whether the blind panels are milled in and how deep (all assumed since 2026-10-13); the blends where the block's ramps meet its flat and the handguard's underside are drawn as plain edges, and what is seen through the slit (black in every photo) isn't known","need":"The handguard's rear end from below and to each side (45 degrees off straight down), close, with the light raking across the block: each counterbore's far wall beside its near one, and the left face's holes looked into; and one blind panel from along its face, the light across it"},{"what":"The bolt assembly's steel rear end behind the receiver's rear face: a disc with a tab up to the T and a pin in the tab, 0.15 in thick, and two bars either side of the handle's shaft. Not drawn: it stands in a lower's buffer tower","need":"Nothing more: four of the photos of 2026-10-05 have it (953843d0ce18, fc6a01b62b5a, bab1880de544, 0dfba70ae389). For the exploded view"}]},"nordic-thread-protector":{"id":"nordic-thread-protector","name":"1/2-28 thread protector (ships on the 22RB)","manufacturer":"Nordic Components","category":"muzzle_device","description":"The fluted stainless sleeve the 22RB kit ships with on its 1/2-28 muzzle thread, open at the front: the barrel's end shows in its mouth. It is the muzzle slot's part until a suppressor or a flash hider takes its place.","weightIncludedIn":"nordic-22rb-upper","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"thread":{"origin":[0,0,0],"note":"Device frame: on the bore axis at the barrel's shoulder (the protector's seam with the barrel), +x toward the muzzle."},"front":{"origin":["{.length}",0,0],"note":"The device's front face: where the build's overall length ends."}},"interfaces":{"thread":{"type":"muzzle_thread","role":"device","anchor":"thread","params":{"thread":"1/2-28"},"flips":false,"note":"Nordic: a 1/2-28 thread protector."}},"materials":{"body":{"label":"Thread protector","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"Bright stainless, fluted along its length (Nordic's photo of it alone, NC22-Barrel-Protector-SS.jpg, references/nordic-22rb-upper 9056e2073f45, and on the barrel, c280084b0a6e; the user's own, off the barrel, c0e654135597): one piece, one look, the barrel's own. Nordic sells it with the upper and names no other finish."}},"components":{"body":{"label":"Thread protector","material":"body"}},"geometry":{"model":"nordic-thread-protector.glb","components":{},"approximations":["A sleeve at its measured length and diameter, flat at both ends, threaded right through (Nordic's photo of it alone, and the user's of it lying beside the bare muzzle: thread from end to end). Until 2026-10-06 it was a tube with a hole the size of the barrel's bore: the barrel's end in its mouth was its own metal.","Its thread is the barrel's, a drawing's gap of 0.004 in outward (no thread of its own is measured, and the gap is not a fit): a helix of the same hand, a plain V, turning with the 22RB's when it is seated on the shoulder. On another barrel the two threads are in step only by chance, which is hidden inside the sleeve.","Not drawn: the flats milled along its outside (in both photos: the face-on view has its front rim round, so they stop short of the face, and no view on file counts them), the chamfer at its mouth."],"ledger":["nordic-thread-protector.length","nordic-thread-protector.od","nordic-22rb-upper.muzzle_thread_major_d","nordic-22rb-upper.muzzle_thread_minor_d","nordic-22rb-upper.muzzle_thread_pitch","nordic-22rb-upper.muzzle_thread_start","nordic-22rb-upper.muzzle_thread_length"]},"profiles":{},"gaps":[{"what":"The flats along its outside: how many, how wide, and where they stop","need":"The protector off the barrel, stood on end and photographed straight down (the user owns it: it is on their 22RB), and once from the side lying down"},{"what":"Its own thread and the chamfer at its mouth: the thread drawn is the barrel's, a gap outward","need":"The same view from above, close: the mouth's chamfer and the thread's crests show as rings"}]},"olight-baldr-s-bl":{"id":"olight-baldr-s-bl","name":"Baldr S BL","manufacturer":"Olight","sku":"BALDRSBLBK","url":"https://www.olight.com/blog/baldr-s-bl-tactical-light-unique-blue-laser","category":"light","description":"Olight's compact pistol light with a blue laser: 800 lumens and a Class IIIa blue laser (440 to 460 nm) out of one light cup, on a built-in 380 mAh battery charged by its magnetic cable. Its patented slide rail mount clamps a Picatinny rail or a Glock's by the insert fitted, with a locking swing arm. Black (BALDRSBLBK) and desert tan.","weight":"olight-baldr-s-bl.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":[0,0,0],"note":"On the rail's face at the middle of the clamp, where the Picatinny insert lies in the rail's slot: +x toward the lens, +y away from the rail."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{},"flips":false,"note":"Olight: \"includes two types of rail adapters to fit both Glock and Picatinny rails, which are suitable for pistols with Picatinny rail (MIL-STD-1913 rail) or GLOCK pistols with mounting slots\"; \"patented sliding rail mount makes the light custom-fit to your specific rail length\". Drawn with its Picatinny insert, the box's \"Picatinny (MIL-STD-1913) Rail Mount Adapter\": one key in one slot. No page on file gives a least rail length."}},"materials":{"body":{"label":"Body","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized_matte","color":"placeholder-black","sku":"BALDRSBLBK","source":"https://blackstoneshooting.com/olight-baldr-s-800-lumens-white-led-blue-laser-black-anodized"},"tan":{"label":"Desert Tan","finish":"anodized_matte","color":"olight-desert-tan","source":"https://blackstoneshooting.com/olight-baldr-s-bl-weapon-light-blue-laser-800-lumens-desert-tan-6975498005124"}},"default":"black","note":"Olight: \"Baldr S BL adopts an aviation aluminum alloy shell and stainless steel attack head, and the surface is tertiary hard anodized\". Black (Blackstone: MPN BALDRSBLBK, UPC 6972378125552; DLT Trading's item BALDRSBLBK) and desert tan (Blackstone: UPC 6975498005124, its number as the maker's not on file), each photographed (DLT's and AR15Discounts' black, AR15Discounts' and Blackstone's tan). The body, the mount and the switches are the anodize's colour on the tan light; the bezel's ring, the swing arm and its knob, the insert and the screw stay black (AR15Discounts 7b0dbbc5cfe8). Battery Junction lists a gunmetal grey (its page answered 429): sold, not photographed here, not offered. Black is the placeholder the lights use, not matched (a black anodize's brightness in a photo is reflection)."},"lens":{"label":"Lens","finish":"glass","recolorable":false,"color":"glass-clear","note":"One opening for both: Olight, \"Note: LED white light, blue laser output from the same light cup mouth.\""},"laser":{"label":"Laser window","finish":"glass","recolorable":false,"color":"placeholder-black","note":"The blue laser's emitter window, a dark disc at the top of the reflector inside the one lens (the front view, DLT c8ea1d0e142d)."},"bezel":{"label":"Bezel","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","note":"Olight: \"stainless steel attack head\". Black on the black light and on the desert tan one (AR15Discounts' photographs of both, 7b0dbbc5cfe8, cf0b974873b3)."},"contact":{"label":"Charging contact","finish":"nickel","recolorable":false,"color":"stainless-natural","note":"The magnetic charging contact on the foot (Olight's post: \"magnetic charging\", and in the box \"MCC (Magnetic Charging Cable) Special Edition x 1\"), a gold disc in DLT's view from the foot (abe200dcde6b): drawn as bright metal, the catalog having no gold."},"hardware":{"label":"Insert, swing arm and screw","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The Picatinny insert's key in the channel, the swing arm's ribbed lever and its knob (the +z side) and the clamp's slotted screw (the -z side): black on both colours of light (AR15Discounts' photograph of the tan light from its +z side, 7b0dbbc5cfe8). The rear switch and the switch paddles are the body's colour on the tan light (the same photograph), so they are drawn in the body's slot."}},"components":{},"geometry":{"components":{"body":"olight-baldr-s-bl.body.glb","rail_clamp":"olight-baldr-s-bl.rail_clamp.glb"},"approximations":["The body, the head and the mount are the side view (Blackstone's picture of the black light, a rendered straight side view, scaled by the published length and height, which agree within 0.5%) across the front view's sections (DLT Trading's close photo from ahead, read by its proportions at the side view's heights): the body a box with its foot's corners rounded, the head turned about its axis from the side view's edge toward the rail, the bezel its own ring from the groove to the front face. The side view is marked BALDR S where the BL is marked BALDR S BL; its outline and every feature on it (the arrows, the windage and elevation screws, the clamp's plate and slotted screw) are the BL's in DLT's photos.","The clamp's channel is MIL-STD-1913's head (lib.rail_seat), its jaws reaching past the rail's face as far as the front view has their tops (0.16 in, a hair past the lower gauge line) and hooking under the head there; the rail's face is read in the front view as the mount's top beside the jaws, a close photo from a little above (± 0.02). The Picatinny insert is a bar across the channel, the rail slot's width less a hundredth, standing key_height (assumed) into the slot under the anchor; the Glock-sized insert the light comes with fitted isn't drawn (the build's rails are MIL-STD-1913's).","The swing arm is drawn as its knob (on the slotted screw's axis, as wide and as far out as the front view has it) and its ribbed lever as a plain plate (lever_thickness assumed) whose outline is the side view's block above the body's rear half; its ribs and the lever's shape at its end aren't drawn. The mount's notches along the body's slide rail, the two screws Olight says fix the slide rail, the selector switch, the red low-battery indicator and the engraving (the selector's marks on the foot among it) aren't drawn; the magnetic charging contact on the foot is its ring (a groove, contact_ring_groove assumed) and its disc.","The body is drawn where Olight's side view has it on its slide rail mount, 0.84 in of it ahead of the clamp's middle and 1.64 behind; the mount lets it slide (\"patented sliding rail mount makes the light custom-fit to your specific rail length\"), by how much no page on file says, and the build draws the one place.","The lens is one disc 0.75 of the head across, set back lens_recess (assumed) in the bezel's bore, with the laser's window a dark disc at the top of the reflector as the front view has it; the reflector's cup and the LED aren't drawn. The rear switch is the side view's outline behind the body, as wide as the view from the foot has its ribbed paddle (its five ribs aren't drawn); the lower switch paddles are in the body's outline, the slit between them and the body's foot filled across the middle."],"ledger":["olight-baldr-s-bl.length","olight-baldr-s-bl.head_diameter","olight-baldr-s-bl.overall_height"]},"profiles":{"side":{"plane":"xy","origin":"the rear end and the clamp's jaws' tops (the picture's up: toward the rail)","offset":{},"points":[[0,-0.805],[0,-0.963],[0.002,-1.003],[0.016,-1.007],[0.023,-1.031],[0.035,-1.045],[0.05,-1.054],[0.24,-1.102],[0.253,-1.097],[0.259,-1.082],[0.261,-1.102],[0.267,-1.108],[0.319,-1.122],[0.327,-1.122],[0.333,-1.113],[0.337,-1.123],[0.339,-1.208],[0.353,-1.22],[0.34,-1.232],[0.34,-1.352],[0.374,-1.377],[0.453,-1.413],[0.546,-1.412],[0.579,-1.388],[0.596,-1.364],[0.644,-1.413],[0.658,-1.416],[1.204,-1.416],[1.996,-1.414],[2.043,-1.413],[2.057,-1.402],[2.131,-1.397],[2.333,-1.398],[2.346,-1.392],[2.376,-1.397],[2.395,-1.373],[2.413,-1.326],[2.45,-1.152],[2.481,-0.862],[2.487,-0.667],[2.478,-0.59],[2.466,-0.561],[2.444,-0.559],[2.432,-0.563],[2.417,-0.552],[2.185,-0.552],[2.159,-0.54],[2.129,-0.517],[2.106,-0.513],[2.147,-0.461],[2.147,-0.228],[2.14,-0.221],[2.085,-0.22],[2.083,-0.075],[2.071,-0.057],[2.019,-0.015],[1.98,-0.004],[1.282,0],[1.253,-0.011],[1.207,-0.055],[1.195,-0.081],[1.193,-0.146],[1.186,-0.148],[1.162,-0.178],[1.113,-0.171],[0.609,-0.19],[0.59,-0.196],[0.577,-0.214],[0.58,-0.476],[0.575,-0.482],[0.576,-0.513],[0.556,-0.514],[0.477,-0.557],[0.453,-0.558],[0.351,-0.616],[0.336,-0.626],[0.336,-0.645],[0.331,-0.655],[0.316,-0.645],[0.294,-0.647],[0.217,-0.7],[0.019,-0.759],[0.005,-0.778]],"scaleRefs":["olight-baldr-s-bl.length","olight-baldr-s-bl.overall_height"],"inputs":{"olight-baldr-s-bl.length":2.48,"olight-baldr-s-bl.overall_height":1.42},"tolerance":0.003,"photo":"references/olight-baldr-s-bl f1a41bae1594 (Blackstone: the Baldr S BL from its -z side, the lens to the right and the clamp up (2500 x 1438))","method":"luminance < 215, closing ×2, largest piece, holes filled; scale from olight-baldr-s-bl.length = 2.48 in (x-extent 2379 px → 959.3 px/in) and olight-baldr-s-bl.overall_height = 1.42 in (y-extent 1355 px → 954.2 px/in), which agree within 0.5%; mean 956.7 px/in; origin at x min, y max of the outline; Douglas-Peucker at 0.003 in with the extremes kept: 83 points (IoU 0.997 with the full outline) (tools/trace.py)","via":"harvest","note":"Picture up is toward the rail (the light frame's -y): the script turns it over. The rear switches' paddles at the left, the body, the head and its bezel at the right; above the body the slide rail mount, its rear block over the slide's notches and its clamp (the near plate with the slotted screw, 1180 to 2030 px)."},"front":{"plane":"zy","origin":"the far jaw's outer face and the jaws' tops","offset":{},"points":[[0,-0.719],[0.003,-0.872],[0.03,-0.918],[0.032,-1.312],[0.056,-1.361],[0.087,-1.392],[0.128,-1.413],[0.472,-1.413],[0.515,-1.421],[0.609,-1.421],[0.643,-1.413],[0.985,-1.411],[1.03,-1.384],[1.059,-1.35],[1.08,-1.299],[1.083,-0.912],[1.104,-0.88],[1.11,-0.864],[1.11,-0.633],[1.091,-0.582],[1.075,-0.555],[1.061,-0.547],[1.069,-0.531],[1.069,-0.49],[1.076,-0.484],[1.272,-0.478],[1.279,-0.472],[1.279,-0.41],[1.265,-0.399],[1.271,-0.38],[1.271,-0.343],[1.26,-0.316],[1.271,-0.302],[1.268,-0.216],[1.229,-0.199],[1.135,-0.199],[1.128,-0.192],[1.128,-0.176],[1.122,-0.164],[1.076,-0.164],[1.069,-0.157],[1.067,-0.047],[1.036,-0.016],[1.012,0],[0.928,0],[0.913,-0.017],[0.908,-0.05],[0.892,-0.06],[0.897,-0.066],[0.892,-0.079],[0.895,-0.085],[0.932,-0.122],[0.909,-0.153],[0.903,-0.146],[0.903,-0.136],[0.896,-0.126],[0.845,-0.113],[0.818,-0.113],[0.813,-0.118],[0.692,-0.118],[0.686,-0.113],[0.474,-0.113],[0.455,-0.121],[0.34,-0.121],[0.334,-0.116],[0.313,-0.116],[0.254,-0.129],[0.219,-0.148],[0.212,-0.154],[0.21,-0.206],[0.203,-0.212],[0.196,-0.206],[0.196,-0.149],[0.172,-0.12],[0.199,-0.09],[0.199,-0.069],[0.193,-0.055],[0.196,-0.009],[0.192,-0.005],[0.117,-0.005],[0.106,-0.013],[0.067,-0.05],[0.059,-0.063],[0.056,-0.458],[0.062,-0.549],[0.055,-0.556],[0.039,-0.556],[0.032,-0.563],[0.013,-0.6],[0.003,-0.641]],"scaleRefs":["olight-baldr-s-bl.width","olight-baldr-s-bl.overall_height"],"inputs":{"olight-baldr-s-bl.overall_height":1.42,"olight-baldr-s-bl.width":1.28},"tolerance":0.003,"photo":"references/olight-baldr-s-bl c8ea1d0e142d (DLT Trading: the Baldr S BL from ahead, the clamp up, the swing arm's knob at the right (+z))","method":"luminance < 215, inside [240, 40, 760, 620], closing ×2, largest piece, holes filled; scale from olight-baldr-s-bl.width = 1.28 in (x-extent 476 px → 371.9 px/in) and olight-baldr-s-bl.overall_height = 1.42 in (y-extent 529 px → 372.5 px/in), which agree within 0.2%; mean 372.2 px/in; origin at x min, y max of the outline; Douglas-Peucker at 0.003 in with the extremes kept: 90 points (IoU 0.997 with the full outline) (tools/trace.py)","via":"harvest","note":"Picture up is toward the rail and picture right the light's +z. A close photo: the head's ring and the body's front end read larger than the jaws behind them; the script takes the body's section from it by its proportions, at the side view's heights."}},"gaps":[{"what":"Gunmetal grey","need":"Battery Junction lists a gunmetal grey Baldr S BL (its page answered 429): a photograph of that colourway before it is offered"},{"what":"How far the body slides on its rail mount","need":"Olight's manual or a page giving the slide rail's travel: the build draws the body where the side view has it, and on the TX22 its head reaches 0.1 to 0.5 in past the thread protector's rear"},{"what":"A view square across the light (from behind, or from below at a distance)","need":"The body's width and the jaws are read through a close front photo by their proportions (± 0.04)"},{"what":"The least rail length, and what it fits beyond Picatinny and Glock rails","need":"A maker's or seller's sentence: none on file names one"},{"what":"Olight's own store page for the Baldr S BL","need":"olight.com's product page wasn't found; Olight Benelux answered 429 and Olight Australia 404"}]},"otter-creek-polonium-k":{"id":"otter-creek-polonium-k","name":"Polonium K","manufacturer":"Otter Creek Labs","sku":"POLK","category":"muzzle_device","description":"A short 5.56 suppressor that threads straight onto a 1/2x28 muzzle: a welded stainless can 1.625 in across with two shallow grooves behind its front cap, a notched collar round the bore, and the hex of its direct thread mount at the rear. Modelled from the outside only. Barrel lengths, in its sellers' words: Capitol Armory, \"7.5\" minimum barrel length (5.56 NATO)\"; Silencer Shop, \"The Polonium K requires a minimum barrel length of 7.5 inches for 5.56/.223 and 7.62x39. For 6 ARC and 6.5 Grendel, the minimum is 10.5 inches.\"; Bauer Precision, \"Barrel Restrictions: 5.56 / .223 / 7.62x39: 7.5 inches minimum 6 ARC / 6.5 Grendel: 10.5 inches minimum .308 / 6.5 CM / .243 Win: 12.5 inches minimum\". Silencer Shop: \"Full-auto rated: Yes\".","weight":"otter-creek-polonium-k.weight","nfa":"silencer","cartridge":{"takes":["5.56 NATO",".223 Rem"],"stated":"6mm bore - rated for 5.56 NATO, .223 Rem, 6mm ARC, 6 Creedmoor, 6 Dasher, .243 Win","source":"Capitol Armory, Otter Creek Polonium K, Features (a seller's page: Otter Creek's own refuses the reader): https://www.capitolarmory.com/otter-creek-labs-polonium-k-556-suppressor.html. Silencer Shop for the same: \"5.56 NATO, .223 Remington, 6mm/.243 (6 ARC, 6mm Creedmoor, 6mm Dasher, .243 Winchester)\" and \"You cannot fire 6.5mm or 7.62mm projectiles through it.\" (https://www.silencershop.com/otter-creek-labs-polonium-k.html). The 6 mm cartridges aren't among the catalog's names yet."},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"ffl":true,"anchors":{"thread":{"origin":[0,0,0],"note":"Device frame: on the bore axis at the barrel's shoulder, +x toward the muzzle. The mount's rear face (its hex's) is taken to bear on the shoulder: the ledger's length says why."},"front":{"origin":["{.length}",0,0],"note":"The tip of the notched collar that stands out of the front face: where the build's overall length ends."}},"interfaces":{"thread":{"type":"muzzle_thread","role":"device","anchor":"thread","params":{"thread":"1/2-28"},"flips":false,"note":"The thread of the mount it is sold with: Capitol Armory, \"a 1/2x28 direct thread mount is included\"; Silencer Shop, \"The included 1/2x28 direct thread adapter covers most 5.56 hosts straight out of the box.\" No page says what length of barrel thread the mount takes, so none is stated here. The suppressor's own rear thread is 1.375x24 (Capitol Armory: \"HUB/Bravo 1.375x24 rear threads\"; Silencer Shop: \"Rear thread: 1.375x24 (HUB standard)\"), and its sellers name other mounts for it, none of them modelled or offered here: Capitol Armory, \"HUB Direct Thread Mounts: Dead Air, SilencerCo, Energetic Armament, YHM / SilencerCo Bravo ASR / Plan-B by Q (Bravo / Omega) / Dead Air Key-Mo (Bravo / Omega), Xeno / EA TBAC Adapter / Any other HUB-compatible solution\"; Silencer Shop, \"Dead Air KeyMo and Xeno, SilencerCo ASR, Q Plan-B, Griffin Armament mounts, YHM Kurz and Phantom, and any other mount built to the 1.375x24 HUB standard.\" With another mount its length and weight are other figures (the sellers' 4.8 in and 11.5 oz are without any)."}},"materials":{"body":{"label":"Suppressor","finish":"cerakote","recolorable":false,"color":"otter-creek-black-cerakote","options":{"black":{"label":"Black","finish":"cerakote","color":"otter-creek-black-cerakote","sku":"POLK","source":"https://www.kygunco.com/product/otter-creek-labs-polk-polonium-k"},"fde":{"label":"Flat Dark Earth","finish":"cerakote","color":"otter-creek-fde-cerakote","sku":"POLKFDE","source":"https://blackstoneshooting.com/otter-creek-polonium-k-suppressor-direct-thread-flat-dark-earth/"}},"default":"black","note":"The welded can, its front cap and collar with it: 17-4 stainless (Capitol Armory: \"H900 heat-treated 17-4 stainless steel\", \"Tubeless CNC-welded construction\") under Cerakote (Capitol Armory's table: \"Color Black / Finish Cerakote\"; KYGunCo: \"Cerakote Finish, Black\"; Blackstone Shooting's table for the flat dark earth one: \"Finish: Cerakote\"). The black is a matte charcoal in every photo (Silencer Central's reads #484848 on its lit side, Capitol Armory's #403e41), not a black. Two colours, by the sellers: Black (KYGunCo and Bauer Precision give the maker's number POLK, UPC 664533654156; Capitol Armory sells it as OCL-POL556K) and Flat Dark Earth (Blackstone Shooting: MPN POLKFDE, UPC 664533654163; Bauer Precision: \"PoloniumK-FDE\", \"Finish: Flat Dark Earth (FDE)\"); Silencer Shop sells both as one page's two colours, \"Black\" and \"Flat Dark Earth\", under its own OCL-POLK-MULTI. No page prints a Cerakote number for either."},"mount":{"label":"Direct thread mount","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The 1/2x28 mount's hex and flange, black in both colourways: Bauer Precision's photo of the flat dark earth K (11ce8a4d4446) has it black under the tan can, as Silencer Central's, Silencer Shop's and Bauer's photos of the black K do. A smooth black with a hard highlight on the hex's edges (6d1e5cc6dd05): a black on finished steel, not fitted to a photo, and no page says what the finish is. Capitol Armory's unit (695e8c80ec35, c937a96aa552) and Blackstone's small picture of the flat dark earth one (3e36ba884614) have a bronze-coloured mount instead; Silencer Shop: \"Note: OCL states direct thread adapters may vary in appearance from product photos.\" Drawn black, as four of the six sets of photos have it."}},"components":{"body":{"label":"Suppressor","material":"body"},"mount":{"label":"Direct thread mount","material":"mount"}},"geometry":{"model":"otter-creek-polonium-k.glb","components":{},"approximations":["The can is turned from figures read off sellers' side photos, not from a drawing: its lengths at the scale of PEW Science's 5.3 in with the mount (the mount's rear face to the collar's tip), its diameters at the published 1.625. The two scales differ by 3.4% in the photo (a black tube reads thin on white); at the length's scale the can alone comes to 4.77 in, inside the sellers' 4.8.","The body, the ring between the two grooves and the front cap are all drawn at 1.625 in. In the photos the body behind the grooves reads 0.003 to 0.009 in under the cap across, in steps at its weld seams; neither the steps nor the seams' hairlines are drawn.","Two grooves 0.014 in deep behind the front cap, placed from Capitol Armory's photo of serial GK12800, their walls drawn at 45 degrees. Silencer Central's and Bauer Precision's photos are of an early unit (GK0104) whose grooves begin at the same places and run 0.04 to 0.05 in further forward: units differ, and the later one is drawn.","The front face from one near face-on photo: a raised rim, a raised cross of four arms and four pockets between them, 0.017 in deep by one oblique photo (a shallow relief: its depth is the least sure figure here), and round the bore a collar 0.41 in across standing 0.095 in out of the face, with four notches. A notch is drawn up and the cross upright and level: which way round they stand on a rifle is where the thread tightens.","Nothing inside is modelled: the hole in the front face is the opening as it shows (0.29 in), cut back to the middle, where it meets the mount's hole run on plain from the rear. One hole right through, so that a barrel's threaded end of any length stands in air, as it does in the real one's first chamber.","The direct thread mount is the black one's hex and flange (0.81 in across the flats, its rear corners relieved at 45 degrees), a piece of its own in its own material, a flat drawn on top. Some units' mounts are bronze-coloured and may differ in form (Silencer Shop: \"OCL states direct thread adapters may vary in appearance from product photos\").","The mount's 1/2-28 thread is a helix cut through it and 0.37 in on into the can (the length of the mount's plug, by its threads counted in one photo; the plug is not a piece of its own), then plain: the Army barrel's thread a drawing's gap of 0.004 in outward, right-hand, turning with the catalog's barrels' so that a barrel's threaded end stands inside it and shares nothing with it. Nothing of the mount's own thread is measured, and what length of barrel thread it takes isn't published.","Seated with the mount's rear face on the barrel's shoulder: the rearmost face in every photo, taken to be what bears there. No page says so.","Not drawn: the engraving, the weld seams, a shallow line round the front cap, the flange's own edge behind the can's rim (it is flush with it), the mount's plug and the 1.375x24 thread inside the can."],"ledger":["otter-creek-polonium-k.length","otter-creek-polonium-k.overall_length","otter-creek-polonium-k.can_length","otter-creek-polonium-k.od","otter-creek-polonium-k.can_rear_x","otter-creek-polonium-k.rear_rim_d","otter-creek-polonium-k.rear_chamfer_x","otter-creek-polonium-k.front_face_x","otter-creek-polonium-k.front_edge_break","otter-creek-polonium-k.grooves","otter-creek-polonium-k.groove_depth","otter-creek-polonium-k.groove_1_x0","otter-creek-polonium-k.groove_1_x1","otter-creek-polonium-k.groove_2_x0","otter-creek-polonium-k.groove_2_x1","otter-creek-polonium-k.collar_od","otter-creek-polonium-k.collar_height","otter-creek-polonium-k.collar_notches","otter-creek-polonium-k.collar_notch_width","otter-creek-polonium-k.bore_d","otter-creek-polonium-k.face_rim_width","otter-creek-polonium-k.face_spoke_width","otter-creek-polonium-k.face_land_d","otter-creek-polonium-k.face_pocket_r","otter-creek-polonium-k.face_pockets","otter-creek-polonium-k.face_pocket_depth","otter-creek-polonium-k.mount_hex_flats","otter-creek-polonium-k.mount_hex_end_d","otter-creek-polonium-k.mount_hex_length","otter-creek-polonium-k.mount_plug_length","otter-creek-polonium-k.thread_pitch","otter-creek-polonium-k.thread_major_d","otter-creek-polonium-k.thread_minor_d"]},"profiles":{},"gaps":[{"what":"What barrel thread the mount takes, and what bears on the barrel's shoulder","need":"Otter Creek's instruction pamphlet (sellers list one in the box; none is hosted where the harvester may read), or the maker's page saved by the user from their own browser"},{"what":"Whether the can is 1.625 in across and 4.8 long as published: sellers' photos read it 3.4% slimmer for its length","need":"a maker's drawing, or a photo with a scale in the can's own plane; black on white reads thin, and the model keeps both published figures"},{"what":"The front face's pockets: how deep they are","need":"a view along the face from its edge, or the maker's drawing: a closed pocket shows in no silhouette, and 0.017 in is one oblique photo's reading against the collar's height"},{"what":"Which grooves a unit sold today has: two units photographed differ by 0.04 to 0.05 in","need":"the maker's page for the current revision"}]},"otter-creek-polonium":{"id":"otter-creek-polonium","name":"Polonium","manufacturer":"Otter Creek Labs","sku":"POL556","category":"muzzle_device","description":"A 5.56 suppressor that threads straight onto a 1/2x28 muzzle: a welded stainless can 1.625 in across with four shallow grooves behind its front cap, a notched collar round the bore, and the hex of its direct thread mount at the rear. Modelled from the outside only. Barrel lengths, in its sellers' words: Capitol Armory, \"BARREL RESTRICTIONS 7.5\" minimum: 5.56/.223 10.5\" minimum: 6 ARC 12.5\" minimum: 6 Creedmoor, 6 Dasher, .243 Win\"; Silencer Shop, \"Barrel Restrictions: 7.5” – 5.56/223 10.5” – 6 ARC 12.5” - 6 Creedmoor, 6 Dasher, 243 Winchester and other 6mm cartridges\"; Bauer Precision, of the flat dark earth one, \"Barrel Length Restrictions 5.56/.223: 7.5\" – 10.3\" Minimum | 6 ARC: 10.5\" – 11.5\" Minimum | 6mm Cartridges: 12.5\" – 14.5\" Minimum\". Silencer Shop: \"Full Auto Rated: Yes\".","weight":"otter-creek-polonium.weight","nfa":"silencer","cartridge":{"takes":["5.56 NATO",".223 Rem"],"stated":"6mm bore. Compatible with 5.56/.223, 6 ARC, 6 Creedmoor, 6 Dasher, and .243 Win","source":"Capitol Armory, Otter Creek Polonium, Features (a seller's page: Otter Creek's own refuses the reader): https://www.capitolarmory.com/otter-creek-labs-polonium-5-56-rifle-suppressor.html. Silencer Shop for the same: \"Multi-Cal Friendly: Ideal for 5.56, also supports 6mm hosts\" (https://www.silencershop.com/otter-creek-labs-polonium.html). The 6 mm cartridges aren't among the catalog's names yet."},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"ffl":true,"anchors":{"thread":{"origin":[0,0,0],"note":"Device frame: on the bore axis at the barrel's shoulder, +x toward the muzzle. The mount's rear face (its hex's) is taken to bear on the shoulder: the ledger's length says why."},"front":{"origin":["{.length}",0,0],"note":"The tip of the notched collar that stands out of the front face: where the build's overall length ends."}},"interfaces":{"thread":{"type":"muzzle_thread","role":"device","anchor":"thread","params":{"thread":"1/2-28"},"flips":false,"note":"The thread of the mount it is sold with: Capitol Armory, \"WHAT'S INCLUDED Otter Creek Labs Polonium suppressor / 1/2x28 direct thread mount / Tube clamp for mount installation\"; Silencer Shop, \"WHAT’S IN THE BOX OCL Polonium Suppressor / 1/2x28 Direct Thread Adapter / Tube Clamp / Owners Manual\". No page says what length of barrel thread the mount takes, so none is stated here. The suppressor's own rear thread is 1.375x24 (Capitol Armory: \"HUB-compatible 1.375x24 rear threads\"; Bauer Precision: \"Universal 1.375x24 HUB Threads\"), and Capitol Armory names other mounts for it, none of them modelled or offered here: \"HUB Direct Thread Mounts: Dead Air, SilencerCo, Energetic Armament, YHM / SilencerCo Bravo ASR / Plan-B by Q / Dead Air Key-Mo, Dead Air Xeno / EA TBAC Adapter / Griffin A2 Adapter / YHM Kurz QD Adapter, Phantom QD Adapter\". With another mount its length and weight are other figures (the sellers' 5.8 in and 13.5 oz are without any)."}},"materials":{"body":{"label":"Suppressor","finish":"cerakote","recolorable":false,"color":"otter-creek-black-cerakote","options":{"black":{"label":"Black","finish":"cerakote","color":"otter-creek-black-cerakote","sku":"POL556","source":"https://www.kygunco.com/product/otter-creek-labs-pol556-polonium-5.56"},"fde":{"label":"Flat Dark Earth","finish":"cerakote","color":"otter-creek-fde-cerakote","sku":"POL556FDE","source":"https://www.bauer-precision.com/otter-creek-labs-polonium-5-56-suppressor-fde/"}},"default":"black","note":"The welded can, its front cap and collar with it: 17-4 stainless (Capitol Armory: \"H900 heat-treated 17-4 stainless steel tubeless construction\") under Cerakote (Capitol Armory: \"Black Cerakote finish\"; Silencer Shop: \"Finish: Cerakote\"; KYGunCo: \"Cerakote Finish, Black\"; Bauer Precision, of the other colour: \"Finish Flat Dark Earth (FDE) Cerakote\"). The black is a matte charcoal in the photos (Bauer Precision's reads #484848 on its lit side, Capitol Armory's #49474a), not a black. Two colours, by the sellers: Black (KYGunCo gives the maker's number POL556, UPC 664533654132; Capitol Armory sells it as OCL-POL556) and Flat Dark Earth (Bauer Precision and Blackstone Shooting: POL556FDE, UPC 664533654149); Silencer Shop sells both as one page's two colours, \"Black\" and \"Flat Dark Earth\", under its own OCL-POL556-MULTI. No page prints a Cerakote number for either."},"mount":{"label":"Direct thread mount","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The 1/2x28 mount's hex and flange, the same under both colourways: black in Bauer Precision's photos of the black Polonium (f243e92704d5, df384dad45d4) and of the flat dark earth one (a7b1407b3473), and in PEW Science's picture of the one it tested (8bfd734724c7). A smooth black on finished steel: not fitted to a photo, and no page says what the finish is. Other units' mounts are bronze-coloured (Capitol Armory's e5f6d6d4781b, Silencer Central's 13e49efb63da, Blackstone's flat dark earth 2352f4807f8d) or grey (Silencer Shop's 45a291775460); Silencer Shop says of the K's, \"OCL states direct thread adapters may vary in appearance from product photos.\" Drawn black."}},"components":{"body":{"label":"Suppressor","material":"body"},"mount":{"label":"Direct thread mount","material":"mount"}},"geometry":{"model":"otter-creek-polonium.glb","components":{},"approximations":["The can is turned from figures read off sellers' side photos, not from a drawing: its lengths at the scale of PEW Science's 6.3 in with the mount (the mount's rear face to the collar's tip), its diameters at the published 1.625. The two scales differ by 1.4% in the photo (a black tube reads thin on white). At the length's scale the can alone comes to 5.86 in where the sellers say 5.8: the mount reads 0.38 in long behind it on this can's photo and 0.44 on the Polonium K's, and each can keeps its own reading.","The body, the three rings between the four grooves and the front cap are all drawn at 1.625 in; the weld seams' hairlines aren't drawn.","Four grooves 0.014 in deep behind the front cap, placed from Capitol Armory's photo of serial G11796, their walls drawn at 45 degrees. Bauer Precision's photo is of a unit whose grooves begin at the same places, run 0.02 to 0.035 in further forward and are 0.004 in deeper: units differ, and Capitol Armory's is drawn, as on the Polonium K.","The front face from a face-on photo of this can: a raised rim, a raised cross of four arms and four pockets between them (0.01 in deep by one oblique photo: a shallow relief, its depth the least sure figure here), and round the bore a collar 0.43 in across with four notches. A notch is drawn up and the cross upright and level: which way round they stand on a rifle is where the thread tightens.","The collar stands 0.062 in out of the face by one side photo, and 0.12 by an oblique photo of another unit: the two readings disagree, the ledger shows both, and the shorter is drawn. The build's overall length is PEW Science's 6.3 either way.","Nothing inside is modelled: the hole in the front face is the opening as it shows (0.29 in), cut back to the middle, where it meets the mount's hole run on plain from the rear. One hole right through, so that a barrel's threaded end of any length stands in air, as it does in the real one's first chamber.","The direct thread mount is the black one's hex and flange (0.80 in across the flats, its rear corners relieved at 45 degrees), a piece of its own in its own material, a flat drawn on top. Other units' mounts are bronze-coloured or grey.","The mount's 1/2-28 thread is a helix cut through it and 0.25 in on into the can (the mount's plug, by a rough count of its threads in one photo; the plug is not a piece of its own), then plain: the Army barrel's thread a drawing's gap of 0.004 in outward, right-hand, turning with the catalog's barrels' so that a barrel's threaded end stands inside it and shares nothing with it. Nothing of the mount's own thread is measured, and what length of barrel thread it takes isn't published.","Seated with the mount's rear face on the barrel's shoulder: the rearmost face in every photo, taken to be what bears there. No page says so.","Not drawn: the engraving, the weld seams, a raised lip at each ring's rear edge that Bauer's and Blackstone's photos show, the flange's own edge behind the can's rim, the mount's plug and the 1.375x24 thread inside the can."],"ledger":["otter-creek-polonium.length","otter-creek-polonium.overall_length","otter-creek-polonium.can_length","otter-creek-polonium.od","otter-creek-polonium.can_rear_x","otter-creek-polonium.rear_rim_d","otter-creek-polonium.rear_chamfer_x","otter-creek-polonium.front_face_x","otter-creek-polonium.front_edge_break","otter-creek-polonium.grooves","otter-creek-polonium.groove_depth","otter-creek-polonium.groove_1_x0","otter-creek-polonium.groove_1_x1","otter-creek-polonium.groove_2_x0","otter-creek-polonium.groove_2_x1","otter-creek-polonium.groove_3_x0","otter-creek-polonium.groove_3_x1","otter-creek-polonium.groove_4_x0","otter-creek-polonium.groove_4_x1","otter-creek-polonium.collar_od","otter-creek-polonium.collar_height","otter-creek-polonium.collar_notches","otter-creek-polonium.collar_notch_width","otter-creek-polonium.bore_d","otter-creek-polonium.face_rim_width","otter-creek-polonium.face_spoke_width","otter-creek-polonium.face_land_d","otter-creek-polonium.face_pocket_r","otter-creek-polonium.face_pockets","otter-creek-polonium.face_pocket_depth","otter-creek-polonium.mount_hex_flats","otter-creek-polonium.mount_hex_end_d","otter-creek-polonium.mount_hex_length","otter-creek-polonium.mount_plug_length","otter-creek-polonium.thread_pitch","otter-creek-polonium.thread_major_d","otter-creek-polonium.thread_minor_d"]},"profiles":{},"gaps":[{"what":"What barrel thread the mount takes, and what bears on the barrel's shoulder","need":"Otter Creek's instruction pamphlet (sellers list one in the box; none is hosted where the harvester may read), or the maker's page saved by the user from their own browser"},{"what":"How far the collar stands out of the front face: 0.062 in by a side photo, 0.12 by an oblique photo of another unit","need":"a straight side view of the muzzle end with the lens level with the front face, or the maker's drawing"},{"what":"Whether the can is 1.625 in across and 5.8 long as published, and how long the mount is behind it: the photos read the can 1.4% slimmer for its length, and the mount 0.38 in on this can and 0.44 on the K","need":"a maker's drawing, or a photo with a scale in the can's own plane"},{"what":"The front face's pockets: how deep they are","need":"a view along the face from its edge, or the maker's drawing"},{"what":"Which grooves a unit sold today has: two units photographed differ by 0.02 to 0.035 in","need":"the maker's page for the current revision"}]},"panzer-ar57-buffer":{"id":"panzer-ar57-buffer","name":"AR57 proprietary carbine buffer","manufacturer":"Panzer Arms","category":"buffer","description":"The heavier carbine buffer the AR57 upper comes with and needs: \"The upper arrives with a custom buffer that fits any carbine AR15 lower\" (Small Arms Review); \"proprietary carbine buffer\" (Classic Firearms); a buyer on Primary Arms' page: \"You must put in the heavier buffer weight that ships with the gun. (4.8 ounces) vs the standard 3oz.\" Not sold on its own.","weight":"panzer-ar57-buffer.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"bore":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the buffer's axis at its head's front face, +x rearward."}},"interfaces":{"bore":{"type":"ar15.extension_bore","role":"buffer","anchor":"bore","params":{},"flips":false}},"materials":{"body":{"label":"Buffer body","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","note":"No photo of it and no word of its finish on file: drawn in the catalog's stand-in black. It is inside the extension, where nothing of it shows on a built rifle."},"bumper":{"label":"Bumper","finish":"polymer","recolorable":false,"color":"placeholder-polymer-black","note":"The standard pattern's bumper (the Army's drawing, 8448619: \"RUBBER, POLYETHER URETHANE\"); its colour on this buffer isn't on file."},"pin":{"label":"Pin","finish":"steel","recolorable":false,"color":"steel-phosphate-dark","note":"The standard pattern's spring pin through the body and the bumper."}},"components":{},"geometry":{"model":"panzer-ar57-buffer.glb","components":{},"approximations":["AN APPROXIMATION: the standard carbine buffer's outside (lib.carbine_buffer: the Army's drawings of the rifle buffer's head, bumper and pin, which the M4's shares, and the reference CAD set's carbine body). No page gives this buffer's size and no photo of it is on file; every sentence about it calls it a carbine buffer, and a heavier one is heavier inside (more or denser weights), not longer.","Its weight is one buyer's (4.8 oz), not a maker's or a seller's figure.","Not drawn: the weights inside it, any mark on it; its colours are the catalog's stand-ins (no photo)."],"ledger":["panzer-ar57-buffer.length","panzer-ar57-buffer.od","std.carbine_buffer.head_thickness","std.carbine_buffer.body_d","std.carbine_buffer.bumper_exposed"]},"profiles":{},"gaps":[{"what":"Its size and look","need":"A photo of it on its own, or the maker's or a seller's figures"},{"what":"Its weight from the maker or a seller (one buyer's 4.8 oz is all that is on file)","need":"Panzer Arms' or a seller's figure"},{"what":"Its part number or name, and whether it is sold alone","need":"A page that lists it"}]},"panzer-ar57-ult-12-upper":{"id":"panzer-ar57-ult-12-upper","name":"AR57 ULT Complete AR-15 Upper Receiver - 5.7x28mm - 12\"","manufacturer":"Panzer Arms","sku":"AR57ULT-12","url":"https://www.primaryarms.com/ar57-ult-complete-upper-assembly-5-7-x28mm-12in","category":"upper","description":"The 12 in AR57: a dedicated 5.7x28mm upper for a mil-spec AR-15 lower, a blowback monobloc receiver with its 12 in barrel inside its M-LOK handguard, a perforated brake on 1/2x28 behind a jam nut at the handguard's lip, its own bolt, handle and buffer, a 13-slot rail over the handle and 3-slot rails above and below the handguard's front block. FN's P90 magazine lies along its top (it ships with one) and it ejects down through the lower's magazine well. Primary Arms: \"intended only for an AR pistol or a legally registered short-barreled rifle\" (of its 12 in barrel). No maker's page is on file.","weight":"panzer-ar57-ult-12-upper.weight","barrelLength":"panzer-ar57-ult-12-upper.barrel_length","cartridge":{"takes":["5.7x28mm"],"stated":"The Panzer Arms AR57 ULT Complete AR-15 Upper Receiver converts any mil-spec AR-15 lower to fire 5.7x28mm ammunition (Primary Arms' description of the 12 in; its specifications: Caliber Gauge 5.7X28mm)","source":"https://www.primaryarms.com/ar57-ult-complete-upper-assembly-5-7-x28mm-12in"},"mass":{"note":"No weight of this upper alone is published (ar-57center.com: \"Upper Weight ~3 lbs\", for both barrels). The receiver with its rails and the handguard in 7075 as drawn (the receiver solid round its bolt, which isn't drawn apart); the barrel, its brake and the brake's nut steel as drawn.","lumps":{"receiver":{"component":"receiver","density":"std.density.aluminium_7075"},"barrel":{"component":"barrel","density":"std.density.steel"},"handguard":{"component":"handguard","density":"std.density.aluminium_7075"}}},"occupies":["barrel","handguard","bolt_carrier_group","charging_handle","muzzle"],"integral":[],"brings":[],"without":{"slots":["gas_block","gas_tube"],"says":"Small Arms Review (Oleg Volk), of the AR57 upper: \"Introduced around 2010, the AR57 blowback upper receiver for the AR15 uses 50-shot P90 magazines\"; \"Operating by simple blowback\". Primary Arms lists what this 12 in's monobloc integrates: \"barrel, muzzle brake, BCG, buffer, and screws\" (no gas parts).","source":"https://smallarmsreview.com/the-second-generation-ar57-drop-in-5-7-upper-for-your-ar/"},"seats":{"magazine":{"parentInterface":"magazine_feed","interface":"feed","apart":[0,1,0],"note":"Small Arms Review, of loading the AR57: \"P90 magazine into the recess on the front of the upper, then press the feed lip side down on the catch located above and slightly back of the bolt.\" Primary Arms: \"a top-loading design similar to the FN P90 that ejects spent cases down through the lower's magazine well\"."}},"requires":[{"slot":"buffer","parts":["panzer-ar57-buffer"],"says":"Small Arms Review (Oleg Volk), of the AR57 upper: \"The upper arrives with a custom buffer that fits any carbine AR15 lower.\" Classic Firearms: \"This upper comes with ultra-lightweight barrel and muzzle brake, proprietary carbine buffer\". A buyer's review on Primary Arms' page for this upper (Hoosier Carry, 2024-03-09): \"You must put in the heavier buffer weight that ships with the gun. (4.8 ounces) vs the standard 3oz.\"","source":"https://smallarmsreview.com/the-second-generation-ar57-drop-in-5-7-upper-for-your-ar/"}],"anchors":{"pins":{"origin":[0,0,0]},"top_rail":{"origin":["{.rail_slot0_x}","{.rail_top_above_pin}",0],"note":"The rear rail's top at its rearmost slot's centre, +x toward the muzzle (picatinny: index = slot number)."},"front_rail":{"origin":["{.front_rail_slot0_x}","{.front_rail_top_above_pin}",0],"note":"The front block's 3-slot rail, its top at its rearmost slot's centre."},"lower_rail":{"origin":["{.lower_rail_slot0_x}","{.lower_rail_bottom_y}",0],"x":[1,0,0],"y":[0,-1,0],"note":"The 3-slot rail under the front block, its face (down) at its rearmost slot's centre: +y out of the rail's face, downward, +x toward the muzzle."},"muzzle":{"origin":["{.brake_rear_x}","{.bore_axis_above_pin}",0],"note":"The barrel's shoulder, where its brake seats (the brake is part of this upper: the muzzle slot is occupied)."},"front":{"origin":["{.muzzle_end_x}","{.bore_axis_above_pin}",0],"note":"The brake's front on the bore axis, where the rifle ends: the overall length's front (readouts.ts), the brake being part of this upper."},"magazine_feed":{"origin":["{.mag_rear_x}","{.mag_underside_y}",0],"note":"Where a seated magazine's own frame stands: on the bore's vertical plane, at the magazine's rear end (its feed end, against the rail block's front face) and its body's flat underside, +x toward the muzzle. Read on Primary Arms' left view with the magazine in (054c636f9e79): each part carries its own half of the seat; its feed boss hangs below this into the receiver's round pocket."},"mlok":{"origin":["{.mlok_upper_front_x} - ({.mlok_upper_slots} - 1) * {std.mlok.slot_pitch}","{.mlok_upper_y}",0],"note":"The upper M-LOK row's rearmost slot's centre on the centre plane at the row's height, +x toward the muzzle; the side faces stand handguard_width / 2 out from it (M10)."},"mlok_lower":{"origin":["{.mlok_lower_front_x} - ({.mlok_lower_slots} - 1) * {std.mlok.slot_pitch}","{.mlok_lower_axis_y}",0],"note":"The lower M-LOK row, on the lower chamfers (detail pass, 2026-10-18): its rearmost slot's x, on the centre plane where the line square to a chamfer through a slot's centre meets it (mlok_lower_axis_y), so a part on a face stands at the slot's centre, mlok_lower_face_distance out along the face's normal. Its slots stand between the upper row's (0.6 of a pitch behind them, as read)."}},"interfaces":{"receiver_pins":{"type":"ar15.upper_lower","role":"upper","anchor":"pins","params":{"pin_spacing":"={std.ar15.pin_spacing}"},"flips":false},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}"},"flips":false,"note":"\"13-slot Picatinny rail over the operating handle\" (Primary Arms): the receiver's own, one piece with it (\"A single block of Aircraft Grade 7075 T6 aluminum ... is used for the receiver and its component rails\", Classic Firearms), its rear end overhanging the receiver's back by 1.1 in."},"front_rail":{"type":"picatinny","role":"rail","anchor":"front_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.front_rail_slots}","beyond_seam":true,"seam_behind":"receiver","seam_ahead":"handguard"},"flips":false,"note":"\"plus 3-slot upper and lower forward rails\" (Primary Arms): the front block's top rail, ahead of the magazine, at the rear rail's height."},"lower_rail":{"type":"picatinny","role":"rail","anchor":"lower_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.front_rail_slots}"},"flips":false,"note":"The 3-slot rail under the front block, facing down (its anchor's +y is down)."},"muzzle":{"type":"muzzle_thread","role":"barrel","anchor":"muzzle","params":{"thread":"1/2-28"},"flips":false,"note":"\"1/2x28 threaded muzzle with perforated muzzle brake\" (Primary Arms). The brake comes on it and is drawn with the barrel."},"magazine_feed":{"type":"p90_magazine","role":"receiver","anchor":"magazine_feed","params":{},"flips":false,"note":"FN's P90 magazine (50 rounds) laid along the top (\"uses 50-shot P90 magazines\", Small Arms Review)."},"mlok":{"type":"mlok","role":"slots","anchor":"mlok","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_upper_slots}","interval":"={std.mlok.interval}","face_distance":"={.handguard_width} / 2","bore":"={.handguard_id}","reach_inside":"={.handguard_width} / 2 - {.barrel_od} / 2"},"faces":{"right":{"angle":90,"note":"the rifle's right side (+z)"},"left":{"angle":-90}},"flips":false,"note":"The upper row, at the bore's height: room inside to the barrel."},"mlok_lower":{"type":"mlok","role":"slots","anchor":"mlok_lower","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_lower_slots}","interval":"={std.mlok.interval}","face_distance":"={.mlok_lower_face_distance}","bore":"={.handguard_id}","reach_inside":"={.mlok_lower_face_distance} - {.barrel_od} / 2"},"faces":{"right":{"angle":"{.lower_face_angle}","note":"the lower chamfer on the rifle's right (about 4 o'clock): its normal from the side face's foot and the keel's top as read, and the keel's width (lower_face_angle)"},"left":{"angle":"0deg - {.lower_face_angle}"}},"flips":false,"note":"The lower row, on the chamfers under the side faces (detail pass, 2026-10-18): from ahead and above (b894132847e8, 46e53e61437f) its slots are foreshortened where the upper row's aren't, so their faces turn down; light shows through them from side to side in the straight view, under the barrel. The room inside is to the barrel, the line square to the face through a slot's centre passing within 0.06 in of the bore's axis."}},"materials":{"receiver":{"label":"Receiver, rails and handguard","finish":"anodized","recolorable":true,"color":"placeholder-black","note":"Primary Arms' specifications for the 12 in: \"Color Black Finish Melonite\", its features \"M-LOK handguard, melonite black coating\" (a nitriding salt bath is steel's: on the 7075 receiver it is read as the seller's word for its black; Primary Arms' page for the 16 in says \"Hardcoat Anodized\"). Sold in black only. A black on an aluminium receiver: its finish type is its look, not fitted."},"barrel":{"label":"Barrel, brake and jam nut","finish":"nitride","recolorable":false,"color":"steel-nitride-black","note":"Primary Arms, of the 12 in: \"Finish Melonite\". The brake and its hex jam nut black in every photo (c261b4c5a32d, 46e53e61437f)."},"bolt":{"label":"Bolt's rear end and magazine catch","finish":"nitride","recolorable":false,"color":"steel-nitride-black","note":"\"8620 alloy bolt\" (Primary Arms), melonite (Classic Firearms): its round rear end, marked UP, in the receiver's rear face (0bde48a31171). And the lever in the rail block's window and out of both its sides (Classic Firearms, of the 16 in: \"ambidextrous mag release\"; 054c636f9e79, fe9d442f7b56), the magazine's catch (Small Arms Review: \"press the feed lip side down on the catch located above and slightly back of the bolt\"), black steel in every photo. Both in the receiver's model."}},"components":{"receiver":{"label":"Receiver and its rail block","material":"receiver"},"handguard":{"label":"M-LOK handguard and front block","material":"receiver"},"barrel":{"label":"Barrel","material":"barrel"}},"geometry":{"components":{"receiver":"panzer-ar57-ult-12-upper.receiver.glb","handguard":"panzer-ar57-ult-12-upper.handguard.glb","barrel":"panzer-ar57-ult-12-upper.barrel.glb"},"approximations":["Its width (1.44 in, ± 0.06) is the 16 in's, by reference: one section, read through cameras fitted to this upper's three-quarter view from ahead (46e53e61437f) and the 16 in's from behind (2026-10-18); the 1.5 assumed until then is kept in the 16 in's ledger. No view of either is square to its end.","Its side outline is Primary Arms' straight right view of this upper (c261b4c5a32d), framed by its own lug holes' near rims. Since 2026-10-18 (night) the photo is read through a camera fitted to its own holes, rails and M-LOK row (the ledger's header): a lens 23 in off and 2.6 in under the pin line, so close that an edge's depth moves its reading by up to 0.15 in, and every reading says where it was taken. Since 2026-10-19 (night) the outline is read through that camera too, each stretch on its face's near edge at that face's depth (the seed's trace spec), and the model takes it as it stands (until then it was mapped ahead of the pivot by a yaw and behind the takedown pin by the rail's scale). Not every silhouette from so low and close a lens is a near edge: an underside seen from below and a face turned toward the lens show their far edge. Where the 16 in's photo, from above and twice as far, reads the edge its silhouette is, its figure is taken (2026-10-20): the handguard's underside 0.098 (this photo 0.058 as the near edge, 0.135 as the far), the lower rail's face -0.093 (-0.150, -0.080); and the takedown lug's front face, a band between its two edges here, is cut to 0.22, where both edges and the 16 in's photo put it (the outline's front, at the near side, 0.46). Batch 10's frame, on the holes' see-through middles, read the photo 1.5% small, the brake 0.28 long and every height 0.04 to 0.07 high: through the camera this upper's readings of the receiver and handguard it shares with the 16 in meet the 16 in photo's (the bore, the rails, the windows, the M-LOK row's foremost slot within 0.01 to 0.02).","Its section is built as the 16 in's (its approximations say how; detail pass, 2026-10-18), its lines read down columns of its own photo: ahead of the seam the handguard's top flat (its width assumed, 0.835: under the magazine in every view), a chamfer down each side to the side face (from the tray to 1.339, read), the side face to 0.713 (read), a chamfer under it with the lower M-LOK row in it to the keel (0.243, read), the keel as wide as the lower block (0.67, read through a camera fitted to 4d5581786e3d, its row of blind holes; 2026-10-19) to the underside, the lower rail's head overhanging it; the chamfers' run across the width (read) less the top flat's (assumed) above and the keel's (read) below (47 degrees from the vertical above, 43 below as drawn). Its front ring from ahead and to the right (46e53e61437f) shows the octagon. The receiver behind the seam has the upper chamfer's plane carried back from its rear face to a ramp under the window (to 1.569 at the top, read: its foot on the handguard's line), its side set in above to the riser's foot; the overhang behind the rear face clear of the buffer tower's ring (its outline, read through the camera on the riser's side, had the ramp's foot 0.04 under the ring's top: put on it, 2026-10-19); the rear rail block at the riser's width (0.62, read: its rows of blind holes through cameras fitted to 4d5581786e3d and 46e53e61437f, 2026-10-19) over the windows' foot, the rail's head overhanging it, the front block over the magazine's flat as the rail head's section carried down; the rear rail's head and teeth are the app's, the front and lower three-slot rails cut in the model to MIL-STD-1913.","The handguard is a shell under a wall's thickness (assumed), its inside the outer section moved in by the wall, open at its front lip, where the brake's jam nut stands (46e53e61437f: an octagonal ring); its two rows of M-LOK slots, six over five (counted on this photo), cut at the standard's size and pitch from the foremost of each row: the upper row square through the side faces, the lower row square through the lower chamfers, see-through under the barrel as the photo has them.","The receiver is drawn solid inside round its bolt (its round rear end in the rear face, assumed size); the opening down into the lower's well isn't drawn. Its underside is the standard's deck, the lugs at the lower's slots less a clearance, its rear lower corner on the lower's rear walls' arc, its rear face the standard's. The magazine's tower sits in a round pocket the tower's size and a clearance (from the magazine's ledger), its floor and the notch in each wall read on this photo; the pocket's centre is the notch's middle moved to the middle plane (feed_pocket_x: the near wall reads 3.8% large on this close photo, by its own M-LOK slots), which puts it where the magazine's tower is. The tower stands out of each side through the notch, as on the 16 in.","The magazine lies on the handguard's top, one plane (tray_top_y is the magazine's underside, read through the camera at the riser's width: from below the photo shows the handguard's top edge hiding the magazine's underside). Its length is its two ends through both photos' cameras (fn-p90-50-magazine.length, 10.869): its round end at mag_rear_x (4.082, read above the latch), the front block's face where its cap stands (14.951), within 0.01 of the cap's front edge read through the camera, and the block cut back to the face under the rail's rear tooth. At the rear the round end stands 0.10 ahead of the rail block's face (3.98, flush with the rail's front end; the traced outline's face there was the magazine's, where the trace took it out, and is put on the face read), white between the two above and below the latch in the photo: the latch stands out of the face from 1.76 to 2.10 (read), as wide as the face (assumed), drawn to the round end and bearing on it; the notch in the magazine's end it goes into isn't drawn. The pocket the tower sits in is drawn round the magazine's tower (concentric with its round end); the notch read in the near wall is 0.105 ahead of it, both kept. Lines along the rifle through the three models meet no gap at the cap's seat or at the latch's. The magazine's raised ring (0.03 proud, assumed) stands that far into the receiver's top, where no photo shows a recess: left, and said.","The barrel is inside the handguard end to end in every view: drawn at the 16 in's diameter from the 16 in's breech (both by reference, assumed) to the brake's jam nut. The nut is a plain hex (its height as it shows read, its turn about the bore assumed: a corner up), the brake a tube at its diameter with a band behind a groove (assumed size), three columns of six ports (two rows show, 60 degrees apart; the far half inferred) and the slot across its front, bored through. The second slot across the first that 46e53e61437f shows from ahead isn't drawn.","Under the rail block: the handle's window through it, the smaller window behind it as a pocket each side, a blind hole under each slot but where a window is (0.1 deep, assumed), and the magazine catch's lever standing in the window and out of each side (its reach assumed): the 16 in's sellers' \"ambidextrous mag release\" (Classic Firearms) and this one's lever out of the right side in c261b4c5a32d. The front block's and the lower block's five holes a side are blind holes.","The charging handle: its channel along the receiver's right side read on this photo, cut 0.1 in deep, the opening in its floor onto the bolt 0.3 deeper, the handle's bar a gap under the side face and its tab 0.2 out of it (the depths and the reach the 16 in's assumptions, by reference); on the left the plate over the same channel as its outline groove (the channel's mirror: no view of this upper's left side is on file, so its screws aren't drawn).","Not drawn: the markings, the magazine release, the handguard's seam as a line (the receiver and handguard are parted along it as two models)."],"ledger":["panzer-ar57-ult-12-upper.handguard_width","panzer-ar57-ult-12-upper.handguard_front_x","panzer-ar57-ult-12-upper.barrel_od","panzer-ar57-ult-12-upper.bore_axis_above_pin","panzer-ar57-ult-12-upper.muzzle_end_x"]},"profiles":{"side":{"plane":"xy","origin":"the takedown pin centre (the rifle frame origin), +x toward the muzzle","offset":{},"points":[[-1.767,2.126],[-1.749,2.06],[-1.66,1.979],[-1.525,1.925],[-1.383,1.905],[-1.218,1.863],[-1.081,1.787],[-1.028,1.739],[-0.976,1.652],[-0.947,1.625],[-0.66,1.529],[-0.509,1.498],[-0.47,1.472],[-0.527,1.408],[-0.58,1.301],[-0.573,1.121],[-0.583,1.11],[-0.574,1.025],[-0.584,1.015],[-0.569,0.856],[-0.821,0.918],[-0.8,0.811],[-0.758,0.703],[-0.658,0.554],[-0.534,0.432],[-0.421,0.358],[-0.331,0.316],[-0.277,0.306],[-0.237,0.279],[-0.217,-0.167],[-0.177,-0.204],[-0.1,-0.225],[0.367,-0.22],[0.378,-0.231],[0.439,-0.199],[0.453,-0.172],[0.45,-0.023],[0.46,-0.013],[0.446,0.147],[0.453,0.189],[0.477,0.216],[0.807,0.219],[0.819,0.209],[1.722,0.217],[1.734,0.206],[3.454,0.221],[3.466,0.211],[4.272,0.218],[4.283,0.207],[6.137,0.213],[6.153,0.197],[6.164,-0.036],[6.189,-0.11],[6.261,-0.189],[6.368,-0.23],[6.516,-0.218],[6.846,-0.056],[7.17,0.042],[7.244,0.042],[7.254,0.053],[7.375,0.044],[7.385,0.054],[8.1,0.061],[8.111,0.05],[10.913,0.065],[10.923,0.054],[12.065,0.064],[12.075,0.054],[12.201,0.065],[12.211,0.055],[14.009,0.061],[14.019,0.05],[14.218,0.062],[14.228,0.052],[14.437,0.043],[14.563,0.003],[14.832,-0.12],[14.935,-0.151],[15.352,-0.137],[15.394,-0.157],[15.456,-0.157],[15.467,-0.146],[15.55,-0.145],[15.561,-0.135],[15.717,-0.133],[15.748,-0.154],[15.841,-0.153],[15.852,-0.143],[16.05,-0.13],[16.06,-0.141],[16.112,-0.14],[16.143,-0.161],[16.175,-0.15],[16.31,-0.149],[16.321,-0.138],[16.582,-0.145],[16.677,-0.053],[16.701,-0.011],[16.706,0.064],[16.767,0.183],[17.047,0.527],[17.202,0.528],[17.202,1.158],[17.151,1.158],[17.11,1.178],[17.079,1.178],[17.014,1.256],[16.988,1.309],[16.931,1.332],[16.869,1.391],[16.761,1.565],[16.657,1.819],[16.558,2.011],[16.381,2.2],[16.371,2.233],[16.331,2.288],[16.302,2.343],[16.291,2.448],[16.245,2.508],[16.183,2.551],[16.066,2.55],[15.905,2.473],[15.869,2.532],[15.843,2.548],[15.705,2.547],[15.512,2.469],[15.487,2.518],[15.44,2.556],[15.312,2.555],[15.13,2.467],[15.093,2.493],[15.057,2.553],[14.882,2.546],[14.879,2.394],[14.819,2.298],[14.809,1.702],[14.855,1.749],[14.851,1.503],[14.707,1.357],[13.575,1.637],[8.898,1.61],[8.887,1.62],[5.772,1.595],[5.761,1.606],[4.518,1.595],[4.475,1.615],[4.176,1.613],[4.159,1.629],[4.114,2.38],[4.147,2.367],[4.145,2.4],[4.094,2.449],[3.961,2.535],[3.639,2.532],[3.593,2.423],[3.448,2.509],[3.372,2.53],[3.243,2.529],[3.196,2.431],[3.029,2.528],[2.858,2.526],[2.799,2.439],[2.643,2.525],[2.461,2.523],[2.428,2.463],[2.402,2.446],[2.269,2.511],[2.181,2.532],[2.064,2.52],[2.016,2.454],[1.973,2.454],[1.86,2.519],[1.709,2.528],[1.7,2.517],[1.667,2.517],[1.608,2.451],[1.442,2.515],[1.27,2.514],[1.232,2.459],[1.189,2.459],[1.012,2.523],[0.904,2.522],[0.835,2.456],[0.813,2.456],[0.625,2.52],[0.507,2.519],[0.438,2.453],[0.26,2.517],[0.099,2.516],[0.05,2.461],[0.007,2.461],[-0.116,2.514],[-0.267,2.513],[-0.318,2.491],[-0.347,2.458],[-0.369,2.458],[-0.535,2.511],[-0.675,2.51],[-0.745,2.455],[-0.933,2.508],[-1.073,2.507],[-1.122,2.463],[-1.176,2.463],[-1.288,2.505],[-1.654,2.503],[-1.715,2.469],[-1.738,2.431],[-1.734,2.387],[-1.702,2.338],[-1.758,2.356],[-1.732,2.312],[-1.726,2.257],[-1.736,2.246],[-1.729,2.181]],"scaleRefs":["panzer-ar57-ult-12-upper.handguard_width","panzer-ar57-ult-12-upper.riser_width","std.picatinny.top_width","std.ar15.rear_lug_slot_width","panzer-ar57-ult-12-upper.lug_clearance","panzer-ar57-ult-12-upper.keel_width","std.picatinny.bevel_width","std.picatinny.lower_gauge_below_top","std.picatinny.bevel_gauge_apart","panzer-ar57-ult-12-upper.top_flat_width"],"inputs":{"panzer-ar57-ult-12-upper.handguard_front_x":17.202,"panzer-ar57-ult-12-upper.handguard_width":1.44,"panzer-ar57-ult-12-upper.keel_width":0.67,"panzer-ar57-ult-12-upper.lug_clearance":0.005,"panzer-ar57-ult-12-upper.riser_width":0.62,"panzer-ar57-ult-12-upper.top_flat_width":0.835,"std.ar15.rear_lug_slot_width":0.5,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"tolerance":0.008,"photo":"references/panzer-ar57-ult-12-upper c261b4c5a32d (Primary Arms AR57ULT-12_02.jpg: the 12 in upper's right side, straight on, 2200 x 1467, the magazine in)","method":"luminance < 200, 2 polygons excluded, closing ×1, largest piece, holes filled; a pinhole camera given in the spec (fitted to its lug holes' near and far rims, its receiver rail's thirteen slots' near edges at two rows, its front rail's near and far edges and its upper M-LOK row's five slots, 0.8 px rms (.cache/ar57-camera/fit12.py, 2026-10-18)): lens 23.1 in from the centre plane, standing over x 11.41, y -2.57, the side leaning 9.6° to the sensor with its bottom nearer and 0.6° with the picture's right nearer; 97.6 px/in on the near face at the lens's foot; each outline point read where its line of sight meets the plane of the edge it is on: 0.72 in out from the centre plane toward the lens (the near face); the rail block's front face at 0.31 (its near corner at the riser's side; the trace's edge there is the magazine's and the latch's, which the model puts on the face read (rail_block_front_x)); the receiver rail's head, its rear end and its teeth at 0.4175 (its rear end turned away from the lens: the near edge, at the head's widest); the riser behind the receiver's rear face, and the ramp under it at 0.31 (turned away from the lens: their near edges, at the riser's side; under it the receiver's rear top corner, at the receiver's side, where the ramp meets it); the receiver's rear lower corner at 0.245 (at the lugs' depth, as the holes' frame read it, so that it meets the takedown lug's rear face as the photo has it; the model cuts it on the lower's arc (lib.upper_rear_corner)); the lugs, the underside between them and the fin at 0.245 (the lugs' near faces, where the holes' near rims are); the handguard's underside at 0.335 (the keel's near side, as handguard_bottom_y is read); the lower block and the lower rail's teeth at 0.328 (the near edge of the lower rail's flat, as lower_rail_bottom_y is read); the handguard's front under the side face at 0.4175 to 0.335 to 0.72 along y (turned away from the lens: the near edge, the section's half width at each height (the lower rail's head, the keel, the lower chamfer to the side face)); the front block's front face at 0.72 to 0.52 to 0.4 to 0.33 to 0.31 along y (turned away from the lens: the near edge, the block's half width at each height as the two views from ahead read it (the side face's at its top, 0.46 to 0.50 at 1.54, the riser's strip under the head)); the front rail's teeth at 0.328 (its top seen from below: the near edge of its flat); the dip ahead of the magazine's flat at 0.4175 (the top flat's near edge, where the ledger's readings there are read (tray_front_y, tray_dip_rear_x)); the cut under the magazine at 0.4175 (the trace's cut along the magazine's underside, which the model puts on the seat's plane; its ends at the top flat's edge); origin at the photo's frame; clipped to x max {.handguard_front_x} = 17.202; Douglas-Peucker at 0.008 in with the extremes kept: 214 points (IoU 0.997 with the full outline) (tools/trace.py)","via":"harvest","note":"Read through the camera the ledger's readings of this photo are read through (2026-10-19; until then in the frame of the lug holes' near rims, mapped ahead of the pivot by a yaw fitted to the brake's front and behind the takedown pin by the rail's scale): each stretch on its edge's depth, the model taking it as it stands. The 12 in upper's outline without its magazine, from its right side: the receiver with its rail block and 13-slot rail, the handguard's top the magazine lies on, the M-LOK handguard with its front block, 3-slot rails above and below, clipped at the handguard's front lip: the barrel and brake are the model's, from the ledger. The lug holes and the see-through M-LOK slots filled."}},"gaps":[{"what":"The left side's plate notch, which no view of this one shows","need":"A left view of this upper"},{"what":"Its barrel's diameter and where its breech is (hidden: drawn as the 16 in's)","need":"A photo of the 12 in barrel out of the upper, or a page's figure"},{"what":"Its weight: no page gives one for this barrel length","need":"A seller's or the maker's weight for the 12 in upper alone"}]},"panzer-ar57-ult-16-upper":{"id":"panzer-ar57-ult-16-upper","name":"AR57 Ultra Light Tactical Complete AR-15 Upper Receiver - 5.7x28mm - 16\"","manufacturer":"Panzer Arms","sku":"ULT0116","url":"https://www.primaryarms.com/panzer-arms-ar57-ultra-light-tactical-5-7x28mm-complete-upper-16in","category":"upper","description":"A dedicated 5.7x28mm upper for a mil-spec AR-15 lower: a blowback monobloc receiver of 7075 aluminium with its 16 in barrel, perforated brake on 1/2x28, bolt, handle and buffer, a 13-slot rail over the handle and an M-LOK handguard with 3-slot rails above and below its front end. FN's P90 magazine lies along its top (it ships with one), and it ejects down through the lower's magazine well, which stays empty. Primary Arms names the maker Panzer Arms (Classic Firearms: \"AR57 Mfg.\"); no maker's page is on file.","weight":"panzer-ar57-ult-16-upper.weight","barrelLength":"panzer-ar57-ult-16-upper.barrel_length","cartridge":{"takes":["5.7x28mm"],"stated":"Panzer Arms AR57 Ultra Light Tactical Complete AR-15 Upper Receiver converts any mil-spec AR-15 lower to fire 5.7x28mm ammunition (Primary Arms' description; its specifications: Caliber Gauge 5.7X28mm)","source":"https://www.primaryarms.com/panzer-arms-ar57-ultra-light-tactical-5-7x28mm-complete-upper-16in"},"mass":{"note":"No weight of this upper alone is published (ar-57center.com: \"Upper Weight ~3 lbs\", for both barrels). The receiver with its rails and the handguard in 7075 as drawn (the receiver solid round its bolt, which isn't drawn apart); the barrel and brake steel as drawn.","lumps":{"receiver":{"component":"receiver","density":"std.density.aluminium_7075"},"barrel":{"component":"barrel","density":"std.density.steel"},"handguard":{"component":"handguard","density":"std.density.aluminium_7075"}}},"occupies":["barrel","handguard","bolt_carrier_group","charging_handle","muzzle"],"integral":[],"brings":[],"without":{"slots":["gas_block","gas_tube"],"says":"Classic Firearms, of the AR57 16\" ULT upper: \"In contrast to many other receivers, there is no gas system to become clogged with carbon or fouling\"; Small Arms Review (Oleg Volk, of the AR57): \"Operating by simple blowback, this upper is available in 6-inch pistol and 16-inch rifle versions.\"","source":"https://www.classicfirearms.com/ar57-5-7x28-ult-upper-receiver/"},"seats":{"magazine":{"parentInterface":"magazine_feed","interface":"feed","apart":[0,1,0],"note":"Small Arms Review, of loading the AR57: \"P90 magazine into the recess on the front of the upper, then press the feed lip side down on the catch located above and slightly back of the bolt.\" Primary Arms: \"a top-loading design similar to the FN P90 that ejects spent cases down through the lower's magazine well\"."}},"requires":[{"slot":"buffer","parts":["panzer-ar57-buffer"],"says":"Small Arms Review (Oleg Volk), of the AR57 upper: \"The upper arrives with a custom buffer that fits any carbine AR15 lower.\" Classic Firearms: \"This upper comes with ultra-lightweight barrel and muzzle brake, proprietary carbine buffer\". A buyer's review on Primary Arms' page for this upper (Hoosier Carry, 2024-03-09): \"You must put in the heavier buffer weight that ships with the gun. (4.8 ounces) vs the standard 3oz.\"","source":"https://smallarmsreview.com/the-second-generation-ar57-drop-in-5-7-upper-for-your-ar/"}],"anchors":{"pins":{"origin":[0,0,0]},"top_rail":{"origin":["{.rail_slot0_x}","{.rail_top_above_pin}",0],"note":"The rear rail's top at its rearmost slot's centre, +x toward the muzzle (picatinny: index = slot number)."},"front_rail":{"origin":["{.front_rail_slot0_x}","{.front_rail_top_above_pin}",0],"note":"The front block's 3-slot rail, its top at its rearmost slot's centre."},"lower_rail":{"origin":["{.lower_rail_slot0_x}","{.lower_rail_bottom_y}",0],"x":[1,0,0],"y":[0,-1,0],"note":"The 3-slot rail under the front block, its face (down) at its rearmost slot's centre: +y out of the rail's face, downward, +x toward the muzzle."},"muzzle":{"origin":["{.brake_rear_x}","{.bore_axis_above_pin}",0],"note":"The barrel's shoulder, where its brake seats (the brake is part of this upper: the muzzle slot is occupied)."},"front":{"origin":["{.muzzle_end_x}","{.bore_axis_above_pin}",0],"note":"The brake's front on the bore axis, where the rifle ends: the overall length's front (readouts.ts), the brake being part of this upper."},"magazine_feed":{"origin":["{.mag_rear_x}","{.mag_underside_y}",0],"note":"Where a seated magazine's own frame stands: on the bore's vertical plane, at the magazine's rear end (its feed end, against the rail block's front face) and its body's flat underside, +x toward the muzzle. Read on Primary Arms' left view with the magazine in (054c636f9e79): each part carries its own half of the seat; its feed boss hangs below this into the receiver's round pocket."},"mlok":{"origin":["{.mlok_upper_front_x} - ({.mlok_upper_slots} - 1) * {std.mlok.slot_pitch}","{.mlok_upper_y}",0],"note":"The upper M-LOK row's rearmost slot's centre on the centre plane at the row's height, +x toward the muzzle; the side faces stand handguard_width / 2 out from it (M10)."},"mlok_lower":{"origin":["{.mlok_lower_front_x} - ({.mlok_lower_slots} - 1) * {std.mlok.slot_pitch}","{.mlok_lower_axis_y}",0],"note":"The lower M-LOK row, on the lower chamfers (detail pass, 2026-10-18): its rearmost slot's x, on the centre plane where the line square to a chamfer through a slot's centre meets it (mlok_lower_axis_y), so a part on a face stands at the slot's centre, mlok_lower_face_distance out along the face's normal. Its slots stand between the upper row's (0.6 of a pitch behind them, as read)."}},"interfaces":{"receiver_pins":{"type":"ar15.upper_lower","role":"upper","anchor":"pins","params":{"pin_spacing":"={std.ar15.pin_spacing}"},"flips":false},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}"},"flips":false,"note":"\"13-slot Picatinny rail over the operating handle\" (Primary Arms): the receiver's own, one piece with it (\"A single block of Aircraft Grade 7075 T6 aluminum ... is used for the receiver and its component rails\", Classic Firearms), its rear end overhanging the receiver's back by 1.1 in."},"front_rail":{"type":"picatinny","role":"rail","anchor":"front_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.front_rail_slots}","beyond_seam":true,"seam_behind":"receiver","seam_ahead":"handguard"},"flips":false,"note":"\"plus 3-slot upper and lower forward rails\" (Primary Arms): the front block's top rail, ahead of the magazine, at the rear rail's height."},"lower_rail":{"type":"picatinny","role":"rail","anchor":"lower_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.front_rail_slots}"},"flips":false,"note":"The 3-slot rail under the front block, facing down (its anchor's +y is down)."},"muzzle":{"type":"muzzle_thread","role":"barrel","anchor":"muzzle","params":{"thread":"1/2-28"},"flips":false,"note":"\"1/2x28 threaded muzzle with perforated muzzle brake\" (Primary Arms). The brake comes on it and is drawn with the barrel."},"magazine_feed":{"type":"p90_magazine","role":"receiver","anchor":"magazine_feed","params":{},"flips":false,"note":"FN's P90 magazine (50 rounds) laid along the top (\"uses 50-shot P90 magazines\", Small Arms Review)."},"mlok":{"type":"mlok","role":"slots","anchor":"mlok","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_upper_slots}","interval":"={std.mlok.interval}","face_distance":"={.handguard_width} / 2","bore":"={.handguard_id}","reach_inside":"={.handguard_width} / 2 - {.barrel_od} / 2"},"faces":{"right":{"angle":90,"note":"the rifle's right side (+z)"},"left":{"angle":-90}},"flips":false,"note":"The upper row, at the bore's height: room inside to the barrel."},"mlok_lower":{"type":"mlok","role":"slots","anchor":"mlok_lower","params":{"pitch":"={std.mlok.slot_pitch}","slots":"={.mlok_lower_slots}","interval":"={std.mlok.interval}","face_distance":"={.mlok_lower_face_distance}","bore":"={.handguard_id}","reach_inside":"={.mlok_lower_face_distance} - {.barrel_od} / 2"},"faces":{"right":{"angle":"{.lower_face_angle}","note":"the lower chamfer on the rifle's right (about 4 o'clock): its normal from the side face's foot and the keel's top as read, and the keel's width (lower_face_angle)"},"left":{"angle":"0deg - {.lower_face_angle}"}},"flips":false,"note":"The lower row, on the chamfers under the side faces (detail pass, 2026-10-18): from ahead and above (b894132847e8, 46e53e61437f) its slots are foreshortened where the upper row's aren't, so their faces turn down; light shows through them from side to side in the straight view, under the barrel. The room inside is to the barrel, the line square to the face through a slot's centre passing within 0.06 in of the bore's axis."}},"materials":{"receiver":{"label":"Receiver, rails and handguard","finish":"anodized","recolorable":true,"color":"placeholder-black","note":"Primary Arms' specifications: \"Color Black Finish Hardcoat Anodized\"; Classic Firearms: \"finished with a beautiful ultra-smooth melonite black coating\" and \"The metal parts, including receiver, rail, barrel, and bolt, are melanite treated\" (a nitriding salt bath is steel's: on aluminium it is read as the sellers' word for its black). Sold in black only. A black on hard anodize: its finish type is its look, not fitted."},"barrel":{"label":"Barrel and brake","finish":"nitride","recolorable":false,"color":"steel-nitride-black","note":"Classic Firearms: \"The metal parts, including receiver, rail, barrel, and bolt, are melanite treated for a hard, durable finish.\" Black in every photo."},"bolt":{"label":"Bolt's rear end and magazine catch","finish":"nitride","recolorable":false,"color":"steel-nitride-black","note":"\"8620 alloy bolt\" (Primary Arms), melonite (Classic Firearms): its round rear end, marked UP, in the receiver's rear face (0bde48a31171). And the lever in the rail block's window and out of both sides of it (054c636f9e79, fe9d442f7b56, b894132847e8, 0bde48a31171; Classic Firearms: \"ambidextrous mag release\"), the magazine's catch (Small Arms Review: \"press the feed lip side down on the catch located above and slightly back of the bolt\"), black steel in every photo. Both in the receiver's model."}},"components":{"receiver":{"label":"Receiver and its rail block","material":"receiver"},"handguard":{"label":"M-LOK handguard and front block","material":"receiver"},"barrel":{"label":"Barrel and brake","material":"barrel"}},"geometry":{"components":{"receiver":"panzer-ar57-ult-16-upper.receiver.glb","handguard":"panzer-ar57-ult-16-upper.handguard.glb","barrel":"panzer-ar57-ult-16-upper.barrel.glb"},"approximations":["Its width (1.44 in, ± 0.06), one figure for the receiver and the handguard, is read through cameras fitted to two three-quarter views (2026-10-18): the 12 in's from ahead and above (46e53e61437f: its front rail, its three M-LOK slots' rims, its side face's lower edge) and this one's from behind and above (0bde48a31171: its receiver rail, the left plate's three screws, four M-LOK slots), the side face being the plane the slots' rims lie on. No view on file is square to its end; the 1.5 assumed until then is kept beside the reading (handguard_width). The magazine's feed tower (1.90 across) stands out of each side through the wall's notch (1.52 long).","Its side outline is Primary Arms' straight left view (054c636f9e79), framed by its two lug holes. The photo is yawed, its muzzle end further from the lens; since 2026-10-18 it is read through a camera fitted to its own features of known size (its lug holes' near and far rims, its two rails' slot edges, its M-LOK row on Magpul's pitch: the ledger's header), which puts every x ahead of the pivot 0.1 to 0.4 in further back than batch 10's correction to the seller's length did, and the brake's front 0.43 short of that length (24 9/16 from the receiver's back, Classic Firearms; through the camera 24.13): the seller's figure stays in the ledger beside the reading. The outline is mapped through x / (1 + k (6.375 - x)), k from the brake's front so read: the camera within 0.03 in at the front block's and the keel's depth, the side faces' edges up to 0.08 forward of it. Heights are read as the photo stands (it is level: the pins within 0.4 px, both rails' tops on one row); the camera reads the front rail's top 0.02 higher and the bore 0.024, not taken up. Its takedown lug's front face is cut to 0.22 (takedown_lug_front_x, 2026-10-20): turned toward the lens, it shows as a band 7 px wide, and the outline's front, at 0.31, is its far edge read as the near one; the handguard's underside (0.098) and the lower rail's face (-0.093) are read through the camera at the edges their silhouettes are, and the outline's run along the underside is put on that plane.","Its section is built of flat faces (detail pass, 2026-10-18, its lines read down columns of 054c636f9e79 and checked on the views from ahead, b894132847e8 and the 12 in's 46e53e61437f): ahead of the seam the handguard has a top flat (its width assumed, 0.835: it is under the magazine in every view), a chamfer down each side to the side face (from the tray to 1.30, read: a dark band in the straight view, the chamfer turned up into the magazine's black underside; lit from above in the views from ahead), the side face to 0.665 (read), a chamfer under it in to the keel (to 0.259, read) with the lower M-LOK row in it (its slots foreshortened from above where the upper row's aren't), and the keel, as wide as the lower block (0.67, read on the 12 in's oblique through its camera, its row of blind holes; 2026-10-19), down to the underside, the lower rail's head overhanging it. How far each chamfer runs across is the width (read) less the top flat's (assumed) above and the keel's (read) below: 51 degrees from the vertical above, 43 below as drawn. The receiver behind the seam has the upper chamfer's plane carried back on each side from its rear face to a ramp under the window (to 1.525 at the top, read: the same line at its foot as the handguard's), its side set in above that to the riser's foot; the rail block over the riser's foot as wide as the riser (0.62, read through cameras on the 12 in's views from ahead, its rows of blind holes; 2026-10-19: the rail's head overhangs it, which the views from behind show only against the dark). The rear rail's head and teeth are the app's (MIL-STD-1913 on the standard pitch from the photo's first slot: the photo's pitch reads 1.5% short); the front block's three-slot rail and the lower one are cut in the model to the same standard.","The handguard is a shell under a wall's thickness (0.12 in, assumed: the slots are seen through, no wall in profile), its inside the outer section moved in by the wall, open at its front lip round the barrel (b894132847e8: an octagonal ring), its top closed, the magazine lying on it: whether it is a channel or a floor isn't seen. Its two rows of M-LOK slots, six over five (counted), are cut at the standard's size and pitch from the foremost of each row (read): the upper row square through the side faces, the lower row square through the lower chamfers, see-through from side to side under the barrel as the photo has them.","The receiver is drawn solid inside round its bolt, which isn't drawn but for its round rear end in the rear face (0.75 across and 0.05 proud, assumed); the opening the spent cases go down through into the lower's well isn't drawn (no view from below on file shows it). Its underside is the standard's deck between and beside the lugs, the lugs at the lower's slots less a clearance (assumed), its rear lower corner on the lower's rear walls' arc (lib.upper_rear_corner), its rear face the standard's.","The magazine's feed tower sits in a round pocket in the receiver's top, as big as the magazine's tower and a clearance (from the magazine's ledger: no view shows the pocket from above), its floor where the photo has the tower's lower edge; the notch in each wall the tower shows through is the photo's (1.52 long). The tower (1.90 across) is wider than the receiver as drawn: it stands out of each side through the notch, a 1.90 circle crossing the walls' outer faces over 1.17 in and their inner over 1.42, both inside the notch, and lines across both models through the pocket meet no wall within the notch (detail pass, 2026-10-18: the 1.90 and the 1.52 are two things, the tower and the notch, and both stand). The magazine lies on the handguard's top and the receiver's under it, one plane (tray_top_y is the magazine's underside, read at 698.5 to 699 px where light shows under its front end; the traced outline's run there, cut at 699 px, is drawn on that plane). Its raised ring ahead of the tower (the magazine's: 0.03 in proud, assumed) stands that far into the receiver's top, where no photo shows a recess: left, and said.","The magazine sits between the front block and the latch on the rail block, its length its two ends through both uppers' cameras (fn-p90-50-magazine.length, 10.869; 2026-10-19): its round end at mag_rear_x (read as the half round it is against the white above the latch, 4.070), the front block's face where its cap stands (14.939), on the cap's front edge read through the camera on the cap's near side, and 0.07 behind the traced outline's face (15.01 through its map): the block filled out to the seat below the magazine's top, its rail's rearmost tooth reaching back over the magazine's top (front_block_rear_x) between the cap's two lugs. At the rear the round end stands 0.10 ahead of the rail block's face (3.97, flush with the rail's front end; the outline's face there was the latch's and the magazine's), white between the two above and below the latch in the photo: the latch stands out of the face from 1.78 to 2.12 (read), as wide as the face (assumed), drawn to the round end and bearing on it; the notch in the magazine's end it goes into isn't drawn. The pocket the tower sits in is drawn round the magazine's tower (concentric with its round end); the notch read in the near wall is 0.05 ahead of it, both kept. Lines along the rifle through the three models meet no gap at the cap's seat or at the latch's.","Under the rail block: the handle's window through it, the smaller window behind it as a pocket each side with a wall's web between (it is dark in the photo, not lit through), and a blind hole under each of the rail's slots (0.1 deep, assumed) but where a window is. The magazine catch's lever stands in the window's rear half and out of each side 0.3 in (assumed): \"ambidextrous mag release\" (Classic Firearms), the lever out of the right side in b894132847e8 and out of the left in 0bde48a31171, a curved tab drawn as a block. The front block's and the lower block's five holes a side are blind holes too.","The brake: a plain tube at its diameter with a band behind a groove (the groove's size assumed), three columns of six ports round (three rows of each column show, 60 degrees apart, clocked 17 degrees above the left side's middle: the far half inferred), and the slot across its front end; bored through at 5.7 mm, the brake's own bore as wide as its slot. The barrel is a plain tube at the diameter it shows from its breech (the sellers' 18 in with the brake back from the brake's front) to the brake. The sellers' 16 in barrel and 2 in more with the brake leave 1.51 in of brake ahead of its shoulder where the photo has 2.13: where the 16 is counted from isn't said.","The charging handle (\"reversible\", Classic Firearms; \"the right-side non-reciprocating handle\", Small Arms Review): its channel along the receiver's right side, read on ar-57center.com's small right view (9d225b7d85c8, 31 px/in), cut 0.1 in deep (assumed), the opening in its floor onto the bolt cut 0.3 deeper (assumed), the handle's flat bar in it a gap under the side face, and its tab standing 0.2 out of the side (assumed), all square-edged blocks; on the left the plate over the same channel as its outline groove and its three screws (read on the left view), its face flush, and the round-topped notch in its lower edge over the channel (read), the plate cut there to the channel's floor. The handle's own shape (its hook, its pins) isn't drawn.","Not drawn: the markings (CAL 5.7 X 28 MM, the AR57 mark, PATENT PENDING), the magazine release, the handguard's seam as a line (the receiver and handguard are parted along it as two models)."],"ledger":["panzer-ar57-ult-16-upper.handguard_width","panzer-ar57-ult-16-upper.handguard_front_x","panzer-ar57-ult-16-upper.barrel_od","panzer-ar57-ult-16-upper.bore_axis_above_pin","panzer-ar57-ult-16-upper.muzzle_end_x"]},"profiles":{"side":{"plane":"xy","origin":"the takedown pin centre (the rifle frame origin), +x toward the muzzle","offset":{},"points":[[-1.723,2.131],[-1.71,2.118],[-1.71,2.069],[-1.642,2],[-1.567,1.962],[-1.492,1.937],[-1.442,1.937],[-1.43,1.925],[-1.38,1.925],[-1.318,1.9],[-1.218,1.887],[-1.106,1.837],[-0.975,1.706],[-0.919,1.6],[-0.894,1.588],[-0.67,1.588],[-0.651,1.569],[-0.651,1.494],[-0.676,1.432],[-0.676,1.382],[-0.688,1.37],[-0.688,1.27],[-0.689,0.771],[-0.676,0.759],[-0.677,0.659],[-0.664,0.646],[-0.652,0.547],[-0.627,0.497],[-0.583,0.453],[-0.446,0.44],[-0.228,0.284],[-0.228,-0.152],[-0.185,-0.196],[-0.147,-0.208],[-0.11,-0.208],[-0.097,-0.221],[0.164,-0.221],[0.177,-0.208],[0.252,-0.196],[0.289,-0.171],[0.295,-0.015],[0.308,-0.003],[0.308,0.222],[0.327,0.24],[0.551,0.24],[0.564,0.253],[1.013,0.24],[1.761,0.239],[1.773,0.252],[1.836,0.252],[2.085,0.251],[2.097,0.239],[2.16,0.239],[2.172,0.251],[2.21,0.239],[2.247,0.239],[2.259,0.251],[2.808,0.251],[2.82,0.238],[2.858,0.238],[2.933,0.238],[2.945,0.251],[6.137,0.248],[6.156,0.23],[6.155,-0.082],[6.193,-0.144],[6.236,-0.188],[6.311,-0.226],[6.374,-0.238],[6.386,-0.226],[6.436,-0.226],[6.648,-0.114],[6.673,-0.114],[6.698,-0.089],[6.723,-0.089],[6.76,-0.064],[6.785,-0.064],[6.885,-0.014],[6.922,-0.014],[6.997,0.023],[7.035,0.023],[7.097,0.048],[7.147,0.048],[7.159,0.06],[7.222,0.06],[7.234,0.073],[7.346,0.073],[7.359,0.085],[14.541,0.092],[15.139,-0.12],[15.301,-0.12],[15.313,-0.108],[15.351,-0.108],[15.37,-0.064],[15.37,-0.015],[15.388,0.004],[15.426,0.004],[15.444,-0.015],[15.457,-0.077],[15.5,-0.108],[15.725,-0.108],[15.744,-0.09],[15.744,-0.04],[15.775,0.016],[15.831,-0.027],[15.843,-0.09],[15.887,-0.108],[16.099,-0.109],[16.13,-0.09],[16.13,-0.04],[16.161,0.016],[16.205,-0.015],[16.217,-0.09],[16.236,-0.109],[16.548,-0.109],[16.616,-0.028],[16.666,0.084],[16.666,0.109],[16.766,0.284],[16.829,0.346],[16.866,0.408],[16.953,0.508],[17.003,0.595],[17.05,0.642],[17.05,1.225],[17.023,1.225],[17.004,1.243],[16.979,1.293],[16.917,1.356],[16.817,1.505],[16.767,1.555],[16.518,2.004],[16.381,2.179],[16.344,2.266],[16.307,2.316],[16.269,2.429],[16.219,2.503],[16.176,2.535],[16.088,2.535],[16.076,2.522],[15.976,2.51],[15.958,2.491],[15.957,2.441],[15.914,2.41],[15.883,2.454],[15.883,2.516],[15.864,2.535],[15.689,2.535],[15.59,2.498],[15.571,2.429],[15.552,2.41],[15.527,2.41],[15.509,2.429],[15.496,2.516],[15.478,2.535],[15.303,2.535],[15.291,2.523],[15.216,2.51],[15.197,2.467],[15.197,2.429],[15.166,2.411],[15.122,2.442],[15.11,2.504],[15.079,2.535],[14.954,2.536],[14.947,1.382],[14.928,1.364],[14.192,1.364],[13.98,1.364],[13.793,1.427],[13.694,1.477],[13.631,1.489],[13.588,1.52],[13.607,1.539],[13.681,1.539],[13.706,1.552],[13.713,1.558],[13.694,1.576],[4.056,1.584],[4.037,1.603],[4.038,2.114],[4.025,2.126],[4.038,2.139],[4.025,2.326],[4.038,2.338],[4.038,2.476],[3.932,2.544],[3.62,2.544],[3.602,2.526],[3.602,2.463],[3.57,2.432],[3.483,2.432],[3.452,2.451],[3.452,2.501],[3.421,2.532],[3.383,2.545],[3.221,2.545],[3.203,2.501],[3.203,2.451],[3.184,2.433],[3.159,2.433],[3.084,2.433],[3.065,2.451],[3.065,2.501],[3.034,2.532],[2.997,2.545],[2.835,2.545],[2.804,2.501],[2.804,2.452],[2.785,2.433],[2.747,2.433],[2.735,2.42],[2.679,2.452],[2.679,2.502],[2.66,2.52],[2.598,2.545],[2.436,2.545],[2.417,2.527],[2.417,2.464],[2.386,2.433],[2.348,2.433],[2.336,2.421],[2.292,2.452],[2.292,2.502],[2.249,2.533],[2.211,2.546],[2.037,2.546],[2.018,2.527],[2.018,2.452],[1.974,2.421],[1.937,2.421],[1.906,2.452],[1.906,2.502],[1.887,2.521],[1.812,2.546],[1.65,2.546],[1.632,2.527],[1.619,2.452],[1.588,2.421],[1.563,2.421],[1.519,2.453],[1.519,2.502],[1.501,2.521],[1.426,2.546],[1.251,2.546],[1.233,2.528],[1.233,2.478],[1.22,2.453],[1.189,2.422],[1.151,2.422],[1.133,2.44],[1.133,2.478],[1.114,2.521],[1.077,2.521],[1.027,2.546],[0.865,2.547],[0.834,2.503],[0.834,2.453],[0.802,2.422],[0.765,2.422],[0.746,2.441],[0.746,2.491],[0.728,2.522],[0.628,2.534],[0.615,2.547],[0.478,2.547],[0.447,2.528],[0.435,2.441],[0.416,2.422],[0.378,2.422],[0.36,2.441],[0.36,2.491],[0.329,2.522],[0.241,2.535],[0.229,2.547],[0.079,2.547],[0.048,2.504],[0.048,2.441],[0.029,2.423],[0.004,2.423],[-0.027,2.441],[-0.027,2.491],[-0.058,2.522],[-0.095,2.522],[-0.158,2.547],[-0.32,2.548],[-0.338,2.529],[-0.351,2.442],[-0.382,2.423],[-0.413,2.442],[-0.413,2.491],[-0.438,2.516],[-0.494,2.535],[-0.557,2.535],[-0.569,2.548],[-0.681,2.548],[-0.719,2.535],[-0.737,2.504],[-0.737,2.442],[-0.756,2.423],[-0.781,2.423],[-0.8,2.442],[-0.8,2.504],[-0.831,2.523],[-0.943,2.536],[-0.956,2.548],[-1.093,2.548],[-1.124,2.529],[-1.136,2.442],[-1.155,2.423],[-1.186,2.442],[-1.186,2.492],[-1.217,2.523],[-1.28,2.523],[-1.292,2.536],[-1.666,2.536],[-1.691,2.524],[-1.722,2.492],[-1.722,2.393],[-1.71,2.38],[-1.71,2.281],[-1.698,2.268],[-1.71,2.256],[-1.71,2.143]],"scaleRefs":["std.ar15.pin_spacing"],"inputs":{"panzer-ar57-ult-16-upper.handguard_front_x_pinframe":17.05,"std.ar15.pin_spacing":6.375},"tolerance":0.008,"photo":"references/panzer-ar57-ult-16-upper 054c636f9e79 (Primary Arms ULT0116_02.jpg: the 16 in upper's left side, straight on, 2200 x 1467, the magazine in)","method":"luminance < 200, 1 polygons excluded, closing ×1, largest piece, holes filled; frame from the reviewed holes takedown, pivot (80.2 px/in, rms 0.000 in over 2 points); origin at the photo's frame; clipped to x max {.handguard_front_x_pinframe} = 17.05; Douglas-Peucker at 0.008 in with the extremes kept: 324 points (IoU 0.998 with the full outline) (tools/trace.py)","via":"harvest","note":"The upper's outline without its magazine: the receiver with its rail block and the 13-slot rail, the tray the magazine lies on, the M-LOK handguard with its front block, 3-slot rails above and below, clipped at the handguard's front lip: the barrel and brake are the model's, from the ledger. The lug holes and the see-through M-LOK slots filled. In the pin frame as traced: ahead of the pivot the model maps x through the yaw correction."}},"gaps":[{"what":"Its width to better than ± 0.06 (read 1.44 through two three-quarter views' cameras, 2026-10-18), and the top flat's under the magazine (assumed 0.835: no view shows it), which the upper chamfers' run is the width less; the front block's sides as they stand (the riser's strip with its holes 0.31 out under the rail's head, a dark band under it, a face below it sloping out to 0.46 to 0.50 at 1.54, through the 12 in's two views from ahead), which the model draws as the rail head's widest carried down to the tray; how far the magazine catch's lever stands out of the rail block's sides (catch_out, assumed 0.3 from the riser's side, so 0.11 nearer the centre each side since the riser was read narrower)","need":"A photo from straight behind or ahead of it"},{"what":"Its weight: no page gives one for this barrel length (ar-57center.com: \"Upper Weight ~3 lbs\" for both)","need":"A seller's or the maker's weight for the 16 in upper alone"}]},"precision-armament-m4-72":{"id":"precision-armament-m4-72","name":"M4-72 Severe-Duty® Compensator","manufacturer":"Precision Armament","sku":"M472-556","url":"https://precisionarmament.com/m4-72-severe-duty-compensator/","category":"muzzle_device","description":"A three-port brake that vents its gas back and up: a round body with a narrow flat along its top, three ports each side cut back toward the shooter, a closed bottom, a ring between two grooves and eight wrench flats at its base. Precision Armament says it \"delivers industry leading recoil reduction of 73-75% for standard 223 Remington\" (its page; its spec sheet: \"over a 70% reduction in recoil energy for most cartridges*\", \"*Based on high precision ballistic pendulum test data\"), and LoadoutRoom reports The Truth About Guns' sled test: \"With the M4-72, the test rig slid back an average of 2.4375 inches. With the standard A2 compensator, the rig slid back 8.4375 inches\" (73.84 percent). Those are their claims; the app works out no recoil figure.","weight":"precision-armament-m4-72.weight","cartridge":{"takes":["5.56 NATO",".223 Rem"],"stated":"Caliber .223/5.56mm (the spec sheet's M472-556 column); \".223/5.56mm model is designed to fit M4/M16/AR15 style rifles and features 1/2-28 threads\"","source":"https://precisionarmament.com/content/documents/INDIVIDUAL_SPEC_SHEETS/specs-m4-72-severe-duty-compensator.pdf and https://precisionarmament.com/m4-72-severe-duty-compensator/ (as cached: harvest.quote)"},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"thread":{"origin":[0,0,0],"note":"Device frame: on the bore axis at the barrel's shoulder, +x toward the muzzle. Its rear face bears on the shoulder (with the maker's timing washer, another product, it bears on that); y up, the narrow flat at the top."},"front":{"origin":["{.length}",0,0],"note":"The front face: where the build's overall length ends."}},"interfaces":{"thread":{"type":"muzzle_thread","role":"device","anchor":"thread","params":{"thread":"1/2-28"},"flips":false,"note":"The maker: \"Thread Size 1/2x28\" (spec sheet), \"features 1/2-28 threads\" (page), \"M4-72-556 | .223 | 1/2-28 RH | AWS-500 (1/2-28)\" (the installation guide's table). No source gives how long a barrel thread it takes: no thread_length. Timing, from the installation guide: \"This compensator features ports which are canted upwards to generate a downward force at the muzzle. For this reason the compensator must be properly 'timed' (indexed) with the narrow flat at the 12 o'clock position (top dead center). It is recommended to use the Precision Armament Accu-Washer™ Muzzle Alignment System\"; \"Alternatively, a peel washer or other multi-shim system will provide adequate alignment for safe bullet clearance. However, it is not recommended to use a crush washer for timing as this can result in unacceptable misalignment.\"; \"Tighten to 20-30 ft-lbs of torque using wrench flats at base of compensator.\" The spec sheet: \"AccuWasher Muzzle Device Alignment System recommended for installation to achieve best performance (not included - not required for AK-47 brake)\", its number for the 5.56 \"A02119\". Drawn as it seats with none: its rear face on the shoulder. What it is for, from the maker's page: \"Warning: Reverse venting design may cause excessive blast/concussion on barrels shorter than 14.5\" and on bullpup style rifles.\"; and its questions: \"Can I put this on my shorter-than-14.5\" barrel? You can, we just don't really recommend it.\" Its page also says: \"Will accept many devices designed to fit over the standard A2 flash suppressor.\""}},"materials":{"body":{"label":"Compensator","finish":"nitride","recolorable":false,"color":"precision-armament-crcn-black","options":{"black":{"label":"Black","finish":"nitride","color":"precision-armament-crcn-black","sku":"A04002","source":"https://www.primaryarms.com/precision-armament-m4-72-severe-duty-5-56-compensator-1-2x28-black"},"stainless":{"label":"Stainless","finish":"steel","color":"precision-armament-matte-stainless","sku":"A04003","source":"https://www.midwestgunworks.com/page/mgwi/prod/a04003"}},"default":"black","note":"One piece of 416 stainless (\"HTSR 416 Stainless Steel Bar, HRC 26-32\", spec sheet), sold in two finishes: \"Available with an advanced Ionbond® high temperature CrCN coating (matte black), or stainless steel in-the-white (satin grey)\" (the maker's page); the spec sheet: \"Finish Black CrCN or Matte Stainless\". The numbers are the sellers': Primary Arms \"SKU: A04002 MPN: A04002\" for the black, Midwest Gun Works \"Code: A04002\" for the black and \"Code: A04003\" for the stainless. Both are photographed by the maker in one pose (a1a4c479327e black, 4edb633eb80e stainless): the whole part one colour in each, nothing of another colour on it (the logo and the marks are engraved in the metal and aren't drawn). Neither is fitted to a photo: the black is a hard coat on steel, drawn under `nitride` as SureFire's DLC is (the catalog has no finish for a PVD coat); the stainless is bare metal, drawn under `stainless`, whose brushed look is brighter than the maker's bead-blasted \"satin grey\" (the stainless photo reads #a5a09b on its narrow flat)."}},"components":{},"geometry":{"model":"precision-armament-m4-72.glb","components":{},"approximations":["Every size is read on the maker's two straight photos of it standing, muzzle up, the narrow flat toward the lens (stainless 4edb633eb80e, black a1a4c479327e, agreeing within 0.01 in), across by the published 0.865 in diameter and along by the published 2.250 in length. At one scale the two figures disagree by 2.4% in the photos: each direction is scaled by its own.","Turned: the base, the two grooves, the ring and the body, each edge broken as the photos show it, and the front face's bevel. Then cut: eight wrench flats at the base (an octagon as wide across its flats as the photo's silhouette there, a flat at the top), the narrow flat along the top of the body and the ring, three ports each side, their openings through the device, the hole through and the thread.","Each port is the notch the view from the top shows: two straight walls, the rear one leaning back 55 degrees from square and the front one 30 (the front port's front wall square), from the outside in to 0.215 in from the axis, its inner corners rounded, cut through the device's whole height on that side. The maker says the vents are \"canted upward\": no view on file shows the cant, and the ports are drawn square to the narrow flat. In the photos each port's rear wall is two faces meeting in a crease at mid-height (Dirty Bird's 8f5caa70bc04, the maker's 1e2ffa21d003): drawn as one face.","Where the light shows through the ports from the side, the device is cut through: a round-cornered opening at each port as the spec sheet's render has it from the side (its lower and upper edges, higher than the axis in the first two ports), placed along the device by each port's own walls in the render.","Inside, a round chamber behind each port, as wide as the front port's opening is tall (0.56 in) and as long as its port is at the outside, the teeth between the ports standing as the baffles: no view on file looks inside. Drawn so, the metal is 2.91 oz of 416 stainless where the maker weighs the part at 2.6: the chambers are likely larger than drawn.","The thread is the Army barrel's 1/2-28 cut as a helix, as deep as the Army compensator's bore (not sourced for this device); the hole ahead of it is the hole's mouth on the front face as one three-quarter photo reads it (0.29 in, ± 0.03).","The engraved logo and marks aren't drawn. The maker's timing washer (Accu-Washer, sold apart) isn't drawn: the device's rear face is on the barrel's shoulder."],"ledger":["precision-armament-m4-72.length","precision-armament-m4-72.od","precision-armament-m4-72.base_af","precision-armament-m4-72.flat_width","precision-armament-m4-72.ports","precision-armament-m4-72.bore_d","precision-armament-m4-72.thread_depth"]},"profiles":{"plan":{"plane":"xz","origin":"the rear face's tip, on the axis (the face itself is about 0.01 in ahead: the lens is 2 degrees off the axis)","offset":{},"points":[[0,0],[0,-0.061],[0.015,-0.272],[0.034,-0.365],[0.05,-0.371],[0.271,-0.371],[0.32,-0.356],[0.328,-0.335],[0.339,-0.329],[0.391,-0.329],[0.411,-0.397],[0.427,-0.415],[0.528,-0.417],[0.541,-0.406],[0.558,-0.338],[0.564,-0.332],[0.623,-0.329],[0.632,-0.338],[0.641,-0.387],[0.657,-0.415],[0.765,-0.417],[0.91,-0.332],[1.059,-0.219],[1.081,-0.212],[1.115,-0.212],[1.126,-0.218],[1.134,-0.235],[1.134,-0.279],[1.124,-0.304],[1.07,-0.387],[1.063,-0.414],[1.186,-0.417],[1.358,-0.305],[1.397,-0.268],[1.465,-0.219],[1.509,-0.204],[1.557,-0.22],[1.564,-0.24],[1.564,-0.274],[1.547,-0.313],[1.508,-0.367],[1.484,-0.414],[1.492,-0.42],[1.607,-0.417],[1.623,-0.404],[1.616,-0.402],[1.621,-0.392],[1.698,-0.324],[1.717,-0.312],[1.786,-0.29],[1.886,-0.222],[1.908,-0.217],[2.028,-0.217],[2.055,-0.226],[2.096,-0.257],[2.103,-0.299],[2.103,-0.372],[2.113,-0.414],[2.119,-0.42],[2.2,-0.42],[2.25,-0.318],[2.25,0.321],[2.208,0.411],[2.2,0.42],[2.18,0.42],[2.115,0.414],[2.106,0.377],[2.101,0.269],[2.086,0.25],[2.038,0.212],[1.982,0.204],[1.928,0.207],[1.872,0.226],[1.788,0.29],[1.759,0.302],[1.607,0.417],[1.486,0.414],[1.513,0.357],[1.557,0.296],[1.567,0.267],[1.562,0.225],[1.534,0.212],[1.482,0.217],[1.382,0.268],[1.304,0.332],[1.277,0.361],[1.189,0.417],[1.063,0.414],[1.075,0.379],[1.134,0.282],[1.134,0.228],[1.127,0.217],[1.115,0.214],[1.078,0.217],[1.044,0.231],[0.988,0.268],[0.961,0.295],[0.888,0.349],[0.768,0.417],[0.657,0.415],[0.644,0.394],[0.626,0.329],[0.572,0.329],[0.562,0.334],[0.546,0.394],[0.528,0.417],[0.435,0.417],[0.422,0.413],[0.404,0.377],[0.391,0.329],[0.332,0.332],[0.322,0.356],[0.278,0.368],[0.04,0.368],[0.024,0.335],[0.017,0.267],[0.007,0.24]],"scaleRefs":["precision-armament-m4-72.overall_length"],"inputs":{"precision-armament-m4-72.overall_length":2.25},"tolerance":0.004,"photo":"references/precision-armament-m4-72 4edb633eb80e (Precision Armament M4-72-SEVERE-DUTY-MUZZLE-BRAKE-SS-FRONT: the stainless one standing, seen square on its narrow flat, on white)","method":"luminance < 240, largest piece, holes filled; rotated -90.0° as declared; scale from precision-armament-m4-72.overall_length = 2.25 in (x-extent 919 px → 408.4 px/in); origin at x min, y center of the outline; Douglas-Peucker at 0.004 in with the extremes kept: 117 points (IoU 0.994 with the full outline); Scaled by the published length over the outline's ends. At that one scale its sizes across read about 2.4% under the published diameter (the ledger's head: the photo is read as stretched along the device); the ledger's figures take each direction by its own published size, and the model is built from them, not from this outline.; checks: height 0.840 ± 0.007 in vs precision-armament-m4-72.od 0.865 ± 0.0005 (confirmed): DISAGREES; height in x [0.06, 0.24] 0.742 ± 0.007 in vs precision-armament-m4-72.base_af 0.766 ± 0.008 (corroborated): DISAGREES; height in x [0.33, 0.37] 0.667 ± 0.007 in vs precision-armament-m4-72.groove_d 0.682 ± 0.008 (corroborated): agrees (tools/trace.py)","via":"harvest","note":"Seen from above, the narrow flat toward the lens: the outline's sides are the rifle's left and right, the ports' notches in both."}},"gaps":[{"what":"The ports' cant upward and the inside between the baffles","need":"a view into the muzzle end, a section drawing, or photos square on each side and from the front"},{"what":"How deep its thread goes and the hole's size inside","need":"a photo into its rear end, or the maker's drawing"},{"what":"Why its two published sizes disagree by 2.4% in the maker's own photos","need":"a seller's straight photo of it from the side on white, or a reviewer's measurement"},{"what":"A design patent, if there is one","need":"a patent number on the maker's own page or packaging (none on its page or spec sheet)"}]},"primary-arms-deluxe-30mm-mount":{"id":"primary-arms-deluxe-30mm-mount","name":"Deluxe AR-15 Scope Mount - 30mm","manufacturer":"Primary Arms","sku":"PADLXSM","url":"https://www.primaryarms.com/primary-arms-deluxe-ar15-scope-mount-30mm-padlxsm","category":"scope_mount","description":"Primary Arms' one-piece cantilever scope mount for a 30 mm tube: \"ideal for M4, AR-15, and similar “flat-top” 1913 Picatinny mounting platforms\", \"Places the center of your 30mm tube scope 1.5 inches above the rail\", with \"2.52 inches of clearance between the rings\". Two cross bolts with slotted nuts clamp it; the scope slides in its two rings before their caps are tightened, which sets the eye relief. The mount Primary Arms sells its SLx 1-6x24 in.","weight":"primary-arms-deluxe-30mm-mount.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":[0,0,0],"note":"Mount frame: on the rail's top under the rear cross bolt, +x forward. That bolt lies in the slot the build names; the front bolt is five slots ahead."},"rings":{"origin":["({.ring_rear_x} + {.ring_front_x}) / 2","{.optical_axis_above_rail}",0],"note":"On the rings' axis midway between the two rings: where a scope's saddle is put at position 0."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":0,"clamp_front":"={.clamp_bolt_spacing}","cross_front":"={.clamp_bolt_spacing}"},"flips":false,"note":"Two cross bolts five slots apart, each a bar across the channel in a recoil slot, with a lock washer and a slotted hex nut on the left (Primary Arms: \"turn the nut clockwise until resistance is encountered. After that, turn another 1/2 turn. If a torque wrench is being used, it is recommended no more than 35-40 in-lbs.\"). It is clamped from the rear bolt, in the slot the build names, to the front one; the base runs 0.4 in behind the rear bolt and about as far ahead of the front. A cantilever mount: the rings stand ahead of the clamp, so the clamp stays on the receiver with the scope forward (the 2012 review's photos have it so: the base on the receiver, the front ring over the hand guard). Primary Arms' guide, of cantilever mounts in general: \"In most cases, cantilever mounts should be placed as far forward on the receiver as possible without bridging the mount onto the handguard.\""},"rings":{"type":"scope_rings","role":"rings","anchor":"rings","params":{"diameter":"={.ring_bore}","rear_ring":"=({.ring_rear_x} - {.ring_front_x}) / 2","front_ring":"=({.ring_front_x} - {.ring_rear_x}) / 2","ring_length":"={.ring_length}"},"flips":false,"note":"Two rings bored 30 mm (\"Fits scopes with 30mm tubes.\"), 3.215 in apart middle to middle and 0.69 long each: the maker's 2.52 in between their faces for a scope's saddle. Four socket-head screws to a cap (no torque for them is published: three buyers name three figures)."}},"materials":{"body":{"label":"Mount","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized_matte","color":"placeholder-black","sku":"PADLXSM","source":"https://www.primaryarms.com/primary-arms-deluxe-ar15-scope-mount-30mm-padlxsm"}},"default":"black","note":"Sold in black only: Primary Arms' table has \"Color Black\", \"Finish Hardcoat Anodized\", and its description \"Aluminum construction, durable matte black anodized finish.\" (Armamat: \"anodized in a matte black coating\"). A matte anodize, the catalog's finish for a matte optic's metal (`anodized_matte`); a black on anodize isn't fitted to a photo: the optics' placeholder black. Piece by piece on Primary Arms' and Armamat's photos: the two caps, the lower halves, the arm, the base and the clamp bar are the one matte black; the eight cap screws, the two cross bolts' heads and their nuts and washers are a glossier black, steel (the `hardware` slot). Nothing is engraved on it in any photo on file."},"hardware":{"label":"Screws","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The eight socket-head screws standing on the caps' ledges, the two cross bolts' round heads on the right and their lock washers and slotted hex nuts on the left: a deeper, glossier black than the mount in every photo (Armamat's large ones have the nuts' corners and the screws' rims worn bright). What they are made of and coated with isn't said on a page on file: drawn as dark steel, the placeholder black (a black on steel isn't fitted to a photo)."}},"components":{"body":{"label":"Mount","material":"body"},"hardware":{"label":"Screws","material":"hardware"}},"geometry":{"model":"primary-arms-deluxe-30mm-mount.glb","components":{},"approximations":["Its side photos are close ones taken from above, so it isn't its silhouette: the arm and the base are the left side view's outline in the frame of the rings' near side flats (good to 1.5% for the arm's side and the clamp bar's face, which stand a little further from the lens), and the rings are built from figures read through a camera set by the 30 mm bore. Heights hang on where the lens stood, which is inferred (the cross bolts come out at the rail's top with it): 0.03 in either way.","No view is square across the mount. The rings' width (1.585 in) and the split's height are read in the plane of the front ring's end face in one long-lens oblique; the base's and the arm's widths (1.2 in, the clamp bar 0.23 more on the left) in the plane of the base's rear end, scaled by its channel taken to be the rail's top: an assumed fit. The arm is drawn about the mid-plane with its right face one with the base's.","Each ring's cap is a ledge either side with a low arch between, concentric with the bore and 0.055 in thick over the tube; the split is 0.15 in above the bore's centre and the lower half is drawn as a U, its walls straight up from the centre to the split, with the cap bored as the arc above: that step of 0.02 in at the split is inferred from the cap being less than a half ring, not seen. The rings are drawn closed on the tube, the split a fine groove with no gap. The facet under each side flat is drawn flat, down to the arm's width.","The arm's and the base's top faces stand 0.07 in over the outline's edge, inside a 45 degree break along each side (0.12 in on the base's right): the breaks' heights are read, how far in they reach is not, and the arm's right one is taken as its left. The base's rear top corner is cut off as both side views show it.","Under the rail's top the clamp is the rail's own head in section (MIL-STD-1913's) down to the lower gauge line, the fixed jaw on the right and the clamp bar's two feet on the left, and plain walls as wide apart as the rail's top below that, not the jaws' hooks. Each cross bolt is drawn as a bar a hair under a recoil slot's size across the channel, its round head 0.03 in proud of the right face, and on the left a nut as two of Armamat's photos have it from its side: a round collar toward the bar and a hexagon slotted across its end (the slot 0.08 in wide and 0.10 deep, read), the stud's end in a round recess; the lock washer under the collar and the groove round it aren't drawn apart. The screws on the caps are plain socket heads with a six-sided socket (the reviewer says Torx), placed across the caps by where their heads stand, not by a reading; a head's taper and its socket are shares of its two read sizes, as the cross bolts' heads' rounding is.","Assumed, with no view that shows it in profile (each a ledger entry that says so): the line between a cap and its lower half and the line along the clamp bar's top, drawn as grooves about a hundredth of an inch wide and deep; how deep the recess in a nut's end is (0.07 in) and how far under the nut's end the stud stops (0.06).","Its weight is the maker's 8.2 oz; as drawn its aluminium and steel come to about 7.8, between that and the 7.3 oz a reviewer weighed."],"ledger":["primary-arms-deluxe-30mm-mount.optical_axis_above_rail","primary-arms-deluxe-30mm-mount.ring_bore","primary-arms-deluxe-30mm-mount.ring_rear_x","primary-arms-deluxe-30mm-mount.ring_front_x","primary-arms-deluxe-30mm-mount.ring_length","primary-arms-deluxe-30mm-mount.ring_width","primary-arms-deluxe-30mm-mount.ring_split_above_axis","primary-arms-deluxe-30mm-mount.arm_width","primary-arms-deluxe-30mm-mount.base_right_z","primary-arms-deluxe-30mm-mount.clamp_bar_outer_z","primary-arms-deluxe-30mm-mount.clamp_bolt_spacing","primary-arms-deluxe-30mm-mount.mount_length","primary-arms-deluxe-30mm-mount.clamp_nut_af","primary-arms-deluxe-30mm-mount.clamp_nut_h","primary-arms-deluxe-30mm-mount.clamp_nut_collar_h","primary-arms-deluxe-30mm-mount.clamp_nut_collar_d","primary-arms-deluxe-30mm-mount.clamp_nut_slot_width","primary-arms-deluxe-30mm-mount.clamp_nut_slot_depth","primary-arms-deluxe-30mm-mount.clamp_nut_recess_d","primary-arms-deluxe-30mm-mount.clamp_stud_d","primary-arms-deluxe-30mm-mount.base_rear_chamfer","primary-arms-deluxe-30mm-mount.base_rear_chamfer_drop","primary-arms-deluxe-30mm-mount.ring_split_groove_width","primary-arms-deluxe-30mm-mount.ring_split_groove_depth","primary-arms-deluxe-30mm-mount.clamp_bar_seam_groove","primary-arms-deluxe-30mm-mount.clamp_nut_recess_depth","primary-arms-deluxe-30mm-mount.clamp_stud_end_below_nut_end"]},"profiles":{"side":{"plane":"xy","origin":"on the rings' axis above the rear cross bolt; the app lowers it by the axis's height above the rail, to the mount's frame","offset":{"y":"optical_axis_above_rail"},"points":[[-0.395,-1.163],[-0.384,-1.624],[-0.367,-1.644],[-0.327,-1.644],[-0.322,-1.639],[-0.307,-1.692],[-0.296,-1.703],[-0.276,-1.698],[-0.294,-1.723],[-0.285,-1.744],[-0.262,-1.77],[-0.251,-1.772],[-0.251,-1.784],[-0.243,-1.792],[-0.217,-1.803],[-0.234,-1.804],[-0.2,-1.817],[-0.091,-1.844],[0.02,-1.84],[0.188,-1.665],[0.197,-1.637],[0.216,-1.622],[0.22,-1.605],[0.225,-1.619],[0.208,-1.651],[0.329,-1.651],[0.342,-1.634],[0.333,-1.593],[0.339,-1.559],[0.354,-1.532],[0.393,-1.496],[0.445,-1.477],[0.609,-1.473],[1.534,-1.485],[1.589,-1.501],[1.611,-1.513],[1.641,-1.542],[1.662,-1.591],[1.666,-1.663],[1.706,-1.669],[1.765,-1.78],[1.798,-1.827],[1.829,-1.843],[1.959,-1.852],[2.076,-1.845],[2.084,-1.84],[2.085,-1.829],[2.092,-1.839],[2.127,-1.791],[2.125,-1.786],[2.118,-1.791],[2.124,-1.775],[2.115,-1.775],[2.108,-1.76],[2.119,-1.771],[2.122,-1.761],[2.139,-1.766],[2.192,-1.682],[2.175,-1.678],[2.178,-1.671],[2.196,-1.674],[2.202,-1.668],[2.205,-1.674],[2.239,-1.677],[2.362,-1.675],[2.371,-1.66],[2.373,-1.431],[2.378,-1.426],[2.585,-1.426],[2.613,-1.41],[2.767,-1.261],[2.834,-1.205],[2.874,-1.177],[2.949,-1.146],[3.013,-1.133],[3.638,-1.134],[4.065,-1.142],[4.188,-1.135],[4.34,-1.1],[4.411,-1.072],[4.54,-1.001],[4.662,-0.897],[4.748,-0.788],[4.816,-0.72],[4.887,-0.621],[4.92,-0.552],[4.963,-0.41],[4.977,0.011],[4.977,0.091],[4.971,0.082],[4.958,0.109],[4.966,0.117],[4.977,0.097],[4.977,0.113],[4.964,0.128],[4.973,0.174],[4.973,0.227],[4.894,0.616],[4.879,0.663],[4.869,0.666],[4.869,0.684],[4.865,0.673],[4.859,0.686],[4.852,0.68],[4.843,0.686],[4.821,0.682],[4.815,0.689],[4.809,0.682],[4.787,0.682],[4.778,0.688],[4.753,0.685],[4.75,0.691],[4.741,0.682],[4.716,0.682],[4.623,0.691],[4.466,0.684],[4.438,0.69],[4.429,0.684],[4.404,0.69],[4.382,0.684],[4.32,0.69],[4.32,0.311],[4.333,0.243],[4.334,0.039],[4.328,-0.057],[4.331,-0.156],[4.325,-0.165],[4.323,-0.279],[4.323,-0.487],[4.305,-0.49],[4.275,-0.623],[4.235,-0.697],[4.187,-0.752],[4.104,-0.811],[4.014,-0.851],[3.946,-0.864],[3.421,-0.86],[3.39,-0.86],[3.383,-0.866],[3.377,-0.86],[2.385,-0.851],[2.261,-0.855],[2.113,-0.852],[2.02,-0.843],[1.933,-0.81],[1.84,-0.742],[1.789,-0.679],[1.761,-0.602],[1.754,-0.404],[1.752,-0.033],[1.758,0.14],[1.745,0.168],[1.76,0.496],[1.759,0.688],[1.765,0.691],[1.765,0.709],[1.692,0.711],[1.683,0.717],[1.34,0.709],[1.334,0.715],[1.296,0.712],[1.293,0.718],[1.287,0.712],[1.266,0.712],[1.262,0.718],[1.247,0.712],[1.198,0.715],[1.167,0.706],[1.164,0.715],[1.153,0.664],[1.117,0.296],[1.117,0.259],[1.124,0.259],[1.124,0.252],[1.114,0.246],[1.115,0.181],[1.124,0.163],[1.112,0.141],[1.114,-0.394],[1.143,-0.706],[1.143,-0.777],[1.116,-0.882],[1.045,-0.988],[0.991,-1.036],[0.929,-1.07],[0.926,-1.076],[0.94,-1.075],[0.932,-1.083],[0.867,-1.086],[0.874,-1.095],[0.852,-1.095],[0.837,-1.083],[0.818,-1.086],[0.809,-1.095],[0.79,-1.095],[0.787,-1.086],[0.778,-1.086],[0.775,-1.092],[0.744,-1.093],[0.741,-1.086],[0.765,-1.086],[0.756,-1.08],[0.731,-1.08],[0.725,-1.086],[0.719,-1.08],[0.694,-1.077],[0.679,-1.09],[0.676,-1.084],[0.673,-1.09],[0.66,-1.084],[0.651,-1.09],[0.636,-1.077],[0.625,-1.082],[0.626,-1.09],[0.614,-1.09],[0.608,-1.081],[0.574,-1.087],[0.537,-1.081],[0.544,-1.089],[0.53,-1.096],[0.527,-1.087],[0.504,-1.086],[0.527,-1.084],[0.527,-1.078],[0.456,-1.078],[0.438,-1.081],[0.439,-1.089],[0.431,-1.091],[0.428,-1.078],[0.407,-1.078],[0.401,-1.085],[0.379,-1.078],[0.365,-1.083],[0.376,-1.091],[0.359,-1.092],[0.357,-1.119],[0.354,-1.1],[0.328,-1.105],[0.331,-1.093],[0.32,-1.079],[0.317,-1.091],[0.303,-1.09],[0.309,-1.099],[0.306,-1.114],[0.314,-1.119],[0.258,-1.116],[0.257,-1.124],[0.248,-1.127],[0.257,-1.136],[0.246,-1.141],[0.271,-1.141],[0.282,-1.145],[0.28,-1.15],[0.03,-1.148],[0.053,-1.143],[0.042,-1.142],[0.03,-1.126],[0.019,-1.134],[0.033,-1.142],[-0.001,-1.148],[-0.375,-1.143],[-0.388,-1.149]],"features":{"bar":[[[2.349,-1.187],[-0.391,-1.182],[-0.389,-1.658],[0.341,-1.655],[0.34,-1.479],[1.63,-1.48],[1.63,-1.672],[2.351,-1.669]]],"nuts":[[[2.21,-1.333],[1.66,-1.335],[1.662,-1.842],[2.212,-1.84]],[[0.185,-1.31],[-0.387,-1.312],[-0.385,-1.856],[0.187,-1.854]]],"split":[[[4.972,0.159],[4.329,0.156],[4.329,0.138],[4.972,0.14]],[[1.756,0.159],[1.113,0.156],[1.113,0.141],[1.756,0.144]]]},"scaleRefs":["primary-arms-deluxe-30mm-mount.ring_rear_x","primary-arms-deluxe-30mm-mount.ring_split_above_axis","primary-arms-deluxe-30mm-mount.ring_front_x"],"inputs":{"primary-arms-deluxe-30mm-mount.ring_front_x":4.65,"primary-arms-deluxe-30mm-mount.ring_rear_x":1.435,"primary-arms-deluxe-30mm-mount.ring_split_above_axis":0.15},"tolerance":0.004,"photo":"references/primary-arms-deluxe-30mm-mount edbba62833fd (Primary Arms PADLXSM_00.jpg: the mount alone, left side (nuts and clamp bar toward the lens), 2000 x 1334; taken from 18 in and from above)","method":"luminance < 110, 2 boxes excluded, largest piece, holes filled; frame from the reviewed holes front_ring, rear_ring (323.4 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.004 in with the extremes kept: 262 points (IoU 0.995 with the full outline); features through the same placement (bar: the separate clamp bar on the left, from the line between it and the base's shoulder down to its two feet; relieved between them up to the rail's top; nuts: the two slotted hex nuts on the studs' ends (their outlines' extents; the studs' ends are at columns 1117 and 1770, rows 1058 and 1063); split: the line between each ring's cap and its lower half, on the near side flat) (tools/trace.py)","via":"harvest","note":"The mount as its left side shows it, turned to face +x, in the frame of its rings' near side flats: the arm's top and underside, the front ring's rounded front lower corner, the slope from the arm's underside down to the base's foot, the base's top and rear end with its chamfered corner, the clamp bar and its nuts. The caps' tops stand at the mid-plane and read 5% small in this frame."}},"gaps":[{"what":"A view square across the mount (from above, or end on), or any drawing","need":"none is published: Primary Arms' gallery has two side views and four obliques, and no manual exists (the item feed's manual fields are empty). primaryarmsoptics.com has a page for this mount with a Manuals section and refuses the reader (403): a page the user could save from their own browser"},{"what":"The weight: the maker's 8.2 oz against a reviewer's scale (7.3 oz) and a shop's table (0.198 kg)","need":"a second weighing, or the maker saying what its figure includes"},{"what":"Heights off the side photos (the base's top, the arm, the split) to better than 0.03 in","need":"a side view from a long lens, level with the mount; or the mount on a rail in a straight side view"},{"what":"The ring cap screws' size, driver and torque, and the cross bolts' thread","need":"not stated by Primary Arms or any seller on file; three buyers' reviews give three torques"},{"what":"The nut's recess and the stud's end in it, and the two fine lines drawn as grooves (the split, the bar's seam)","need":"a close photo of a nut from its end at an angle, and of a ring's split: the depths drawn are assumed and listed"},{"what":"Black matched under the app's light (it is the optics' placeholder)","need":"scripts/color-match.mjs against the black product photos"}]},"primary-arms-slx-1-6x24-gen-iv":{"id":"primary-arms-slx-1-6x24-gen-iv","name":"SLx 1-6x24mm SFP Rifle Scope Gen IV - Illuminated ACSS Nova Fiber Wire Reticle - Red Dot Bright®","manufacturer":"Primary Arms","sku":"PA-SLX-1-6X24S-NOVA","url":"https://www.primaryarms.com/primary-arms-slx-1-6x24mm-sfp-rifle-scope-gen-4-illuminated-acss-nova-fiber-wire-reticle","category":"scope","description":"A 1-6x low-power variable scope (second focal plane, illuminated ACSS NOVA reticle) on a 30 mm tube, 10.4 in long: capped turrets, an illumination knob on the left with its battery under the cap, and \"an integrated dovetail throw lever\" on the magnification ring. It comes without a mount (T.REX ARMS lists what is in the box: the scope, a cleaning cloth, two scope caps and two allen keys; Primary Arms' page says \"Mount Compatibility 30mm\"): it goes in a scope mount bored for a 30 mm tube and slides in the rings to set its eye relief. Drawn as photographed: magnification at 1x, the throw lever straight up.","weight":"primary-arms-slx-1-6x24-gen-iv.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"optical_axis":{"origin":[0,0,0],"note":"Scope frame: on the optical axis, +x toward the objective. The origin is the eyepiece's rear face (each photo's own end face, read behind its rim's arc)."},"tube":{"origin":["{.saddle_x}",0,0],"note":"On the optical axis at the middle of the turret saddle, where the turrets' axes cross it: what a mount's rings are placed by (the saddle midway between them at position 0)."},"objective":{"origin":["{.objective_front_x}",0,0],"note":"The objective's front face, on the axis."},"eyepiece":{"origin":["{.eyepiece_rear_x}",0,0],"note":"The eyepiece's rear face, on the axis. Primary Arms gives one eye relief behind it for the whole range: 4.00 in."}},"interfaces":{"tube":{"type":"scope_rings","role":"tube","anchor":"tube","params":{"diameter":"={.tube_od}","rear_from":"={.tube_rear_from} - {.saddle_x}","rear_to":"={.tube_rear_to} - {.saddle_x}","front_from":"={.tube_front_from} - {.saddle_x}","front_to":"={.tube_front_to} - {.saddle_x}"},"flips":false,"note":"A 30 mm main tube (the manual: \"Tube Diameter: 30 mm\"; the page: \"Mount Compatibility 30mm\"), with 2.6 in of it behind the saddle, back to the cone ahead of the magnification ring, and 3.1 in ahead, to the objective's front: a straight tube with no bell. The saddle is 1.48 in long. Primary Arms states no ring height or ring spacing for this scope, and its manual has no mounting section; its own 30 mm mounts (not parts here) put the tube's centre 1.5 in above the rail."},"sight_line":{"type":"optic.sight_line","role":"sight","params":{"magnification":"1-6x"},"flips":false,"note":"A variable scope, 1x to 6x (\"Magnification 1X - 6X\"; the manual: \"Magnification [Min/Max]: 1 - 6x\")."}},"eye":{"anchor":"eyepiece","relief":["{.eye_relief}"],"note":"Primary Arms: \"Eye Relief 4.00 in\" (the manual: \"Eye Relief: 4 in\"): one figure, not given for 1x and 6x apart."},"materials":{"body":{"label":"Scope","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized_matte","color":"placeholder-black","sku":"PA-SLX-1-6X24S-NOVA","source":"https://www.primaryarms.com/primary-arms-slx-1-6x24mm-sfp-rifle-scope-gen-4-illuminated-acss-nova-fiber-wire-reticle"},"fde":{"label":"Flat Dark Earth","finish":"anodized_matte","color":"primary-arms-fde","sku":"PA-SLX-1-6X24S-NOVA-FDE","source":"https://www.primaryarms.com/primary-arms-slx-1-6x24-sfp-rifle-scope-geniv-illuminated-acss-nova-fiber-wire-reticle-fde"}},"default":"black","note":"Primary Arms sells this exact scope (the Gen IV SFP body with the red ACSS NOVA reticle) in two colours, each under its own number on its own page: black, PA-SLX-1-6X24S-NOVA (MPN 610183; \"Color Black\"), and flat dark earth, PA-SLX-1-6X24S-NOVA-FDE (MPN 610207; \"Color Flat Dark Earth\", \"Flat Dark Earth anodized finish\", an \"Online Exclusive\"). A matte anodize (`anodized_matte`, the catalog's finish for a matte optic): Primary Arms' words for the tan one, and its photos of both have no bright line anywhere on the scope; T.REX ARMS of the black one: \"Durable anodized finish\". Piece by piece (2026-10-13), on Primary Arms' photos of the flat dark earth scope (58d97f74fa18 from the rear right, 79813964dc56 from the front left, f0400992d947 from the rear left) and of the black one (a56a99961f90, cda95268212d): the tube, the saddle, both turret caps, the illumination knob with its numbered dial and its battery cap, the magnification ring, the throw lever, the eyepiece and the diopter ring are the one colour on each; the plug low on the saddle too. On the tan scope the round PA medallion in each turret cap stays black (the `medallion` slot) and the lever's two screws are dark (`hardware`); on the black one both are black with it. The lettering (pale grey on tan, white on black) isn't drawn, nor the two lens covers it ships with. The tan is fitted under the app's light to the battery cap's face in two of the photos; black is the placeholder the other black optics use. Other products on the same body, not colourways of this one: the green NOVA (PA-SLX-1-6X24S-NOVA-G), the NOVA 5.56/.308 (PA-SLX-1-6X24S-NOVA-5.56) and the Aurora reticles (PA-SLX-1-6X24S-AUR-5Y6 and its siblings), each its own number and page."},"lens":{"label":"Lenses","finish":"glass","recolorable":false,"color":"glass-clear"},"medallion":{"label":"Turret cap medallions","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","note":"The round PA mark set in the middle of the elevation and the windage cap's top face: black on the flat dark earth scope as on the black one (Primary Arms' photos of PA-SLX-1-6X24S-NOVA-FDE, 58d97f74fa18 and 12d82ab6fdd6: a black disc with the mark raised on it, against the cap's tan). What it is made of isn't said on a page on file: drawn as the scope's own matte black. The raised mark isn't drawn."},"hardware":{"label":"Throw lever screws","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The two socket-head screws in the pocket of the throw lever's base: dark on the flat dark earth scope (58d97f74fa18, where they show black in the tan lever) as on the black one. Their coat isn't said on a page on file: drawn as dark steel, the placeholder black (a black on steel isn't fitted to a photo)."}},"components":{"body":{"label":"Scope","material":"body"},"lens":{"label":"Lenses","material":"lens"},"medallion":{"label":"Turret cap medallions","material":"medallion"},"hardware":{"label":"Throw lever screws","material":"hardware"}},"geometry":{"model":"primary-arms-slx-1-6x24-gen-iv.glb","components":{},"approximations":["The scope's body is its traced side view turned about the optical axis: Primary Arms' right side view of the Aurora 5.56 yard sibling (the same body by its pages: the same stated length and weight, the same optic manual file), scaled by the 30 mm tube column by column and by the published 10.4 in between the end faces. At the tube's scale that photo reads 10.26 in face to face (1.4% short), as the left side view does; the manual's photo from above reads 10.40. The lettering on the eyepiece, which is what differs on this scope (ACSS NOVA), and every other marking aren't drawn.","The turret saddle is drawn as a ball about the turrets' station, 0.947 in in radius, with a flat under each cap and one beneath: the radius is the one at which a ball meets the tube where the side outline does, and the side outline's shoulders follow it. No view is square to the saddle between two turrets; the oblique photos show it round there. The three caps' seats are taken alike, 0.74 in from the axis: the photo from above has both side knobs' skirts beginning that far out, as the side view has the elevation cap's.","The elevation cap is its traced side outline turned about its own axis, and the windage cap is the same cap out of the right side: the photo from above has it at the same stations (skirt, two rows of lugs, a groove between, 1.234 in out where the elevation cap stands 1.232 up). Each row's lugs are cut as counted, eighteen to the turn (the windage cap seen face-on), a lug and a notch by turns of the same width, the notches down to the skirt's radius and on up the top chamfer; the two rows' lugs are drawn in line. Each cap is turned as drawn, not as photographed. The round medallion in the middle of each top face is a piece of its own, drawn flat: its raised PA mark isn't.","The magnification ring is turned at its lugs' tops and its lugs cut: eighteen places 20 degrees apart round each of its two rows, the gaps between lugs as deep as the waist between the rows (they read as one surface in the side views), so each lug keeps the chamfered inner end the outline has. The place on top is the throw lever's dovetail, which the lever's base covers; the place underneath is at the silhouette's edge in both side views and is drawn as a lug. The count rests on the lugs' spacing over the half turn each side view shows (their edges repeat every 19.5 to 19.8 degrees: eighteen, not seventeen); whether the place underneath has a lug needs a view from one end.","The diopter ring at the rear has its eighteen blocks as pockets cut between them, 0.03 in deep, which isn't read (their places along the ring and their count are). The numbered band of the magnification ring is smooth, as it is.","The illumination knob is the outline the manual's photo from above has of it (66 px to the inch: each of its radii is good to 0.02 in), turned about its own axis out of the left side: the numbered dial next to the saddle, two rows of lugs, and the battery cap. Its lugs are cut eighteen to the turn (the knob seen face-on), from the first row out through the cap's rim, as deep as the grooves between its rows show in that photo (0.045 in). The coin slot across the cap is its read length and width, cut 0.04 in deep, which isn't read, and lies as photographed. The numerals aren't drawn.","The small round slotted plug low on the saddle's left, behind the illumination knob, is drawn where the left side view has its middle, standing 0.05 in off the ball along the ball's own radius; how far it stands off isn't read, and its slot isn't drawn. No page says what it is.","The throw lever is its traced side outline across a width of 0.30 in, read off one oblique photo (± 0.06). Its base stands on the ring's top place; the dovetail under it isn't drawn apart from it. The pocket in its base's top is drawn as a plain slot round its two screws, 0.03 in deep at its front end (not read); the screws' heads are plain discs. Drawn at 1x with the lever straight up, as photographed: the lever swings round with the magnification ring.","The glass sits inside each end: the objective's 24 mm lens 0.40 in behind the front face in a mouth 1.02 in across, the eye lens 0.25 in inside the rear rim down a tapered wall. Neither depth is read (the mouth goes black behind its thread, which isn't drawn); the diameters are.","Primary Arms' 17.85 oz is the scope with its battery and without its lens covers; the two flip covers it ships with (\"Scope caps included\") aren't drawn."],"ledger":["primary-arms-slx-1-6x24-gen-iv.length","primary-arms-slx-1-6x24-gen-iv.width","primary-arms-slx-1-6x24-gen-iv.tube_od","primary-arms-slx-1-6x24-gen-iv.saddle_x","primary-arms-slx-1-6x24-gen-iv.tube_rear_from","primary-arms-slx-1-6x24-gen-iv.tube_rear_to","primary-arms-slx-1-6x24-gen-iv.tube_front_from","primary-arms-slx-1-6x24-gen-iv.tube_front_to","primary-arms-slx-1-6x24-gen-iv.objective_front_x","primary-arms-slx-1-6x24-gen-iv.eyepiece_rear_x","primary-arms-slx-1-6x24-gen-iv.saddle_radius","primary-arms-slx-1-6x24-gen-iv.elevation_top_above_axis","primary-arms-slx-1-6x24-gen-iv.windage_reach","primary-arms-slx-1-6x24-gen-iv.illumination_reach","primary-arms-slx-1-6x24-gen-iv.lever_tip_above_axis","primary-arms-slx-1-6x24-gen-iv.cap_d","primary-arms-slx-1-6x24-gen-iv.cap_lugs","primary-arms-slx-1-6x24-gen-iv.magnification_ring_lug_places","primary-arms-slx-1-6x24-gen-iv.diopter_ring_lugs","primary-arms-slx-1-6x24-gen-iv.illumination_knob_lugs","primary-arms-slx-1-6x24-gen-iv.lever_width"]},"profiles":{"body":{"plane":"xy","origin":"on the optical axis at the eyepiece's rear face (the right-side photo's column 161.0, where its end face reads zero behind its rim's arc): the scope's frame","offset":{},"points":[[-0.194,0.013],[-0.194,-0.014],[-0.189,-0.02],[-0.189,-0.188],[-0.183,-0.193],[-0.178,-0.334],[-0.172,-0.34],[-0.167,-0.427],[-0.162,-0.432],[-0.162,-0.465],[-0.156,-0.47],[-0.156,-0.503],[-0.151,-0.508],[-0.14,-0.59],[-0.101,-0.72],[-0.074,-0.774],[-0.049,-0.804],[-0.016,-0.821],[0.033,-0.826],[0.049,-0.837],[0.115,-0.848],[0.121,-0.854],[0.23,-0.854],[0.241,-0.849],[0.247,-0.854],[0.29,-0.854],[0.296,-0.86],[0.34,-0.86],[0.345,-0.866],[0.405,-0.866],[0.411,-0.871],[0.471,-0.866],[0.477,-0.861],[0.488,-0.861],[0.499,-0.872],[0.548,-0.872],[0.559,-0.866],[0.57,-0.872],[0.575,-0.861],[0.581,-0.872],[0.828,-0.873],[0.833,-0.868],[1.64,-0.871],[1.645,-0.865],[1.788,-0.866],[1.794,-0.872],[1.81,-0.866],[1.821,-0.872],[1.827,-0.866],[1.975,-0.867],[1.981,-0.872],[2.025,-0.872],[2.03,-0.856],[2.036,-0.862],[2.096,-0.862],[2.102,-0.867],[2.168,-0.868],[2.173,-0.851],[2.212,-0.895],[2.228,-0.895],[2.234,-0.906],[2.47,-0.907],[2.542,-0.88],[2.558,-0.886],[2.564,-0.875],[2.597,-0.875],[2.624,-0.864],[2.657,-0.859],[2.668,-0.864],[2.674,-0.859],[2.707,-0.875],[2.8,-0.897],[2.822,-0.908],[3.054,-0.909],[3.095,-0.836],[3.095,-0.803],[3.111,-0.803],[3.111,-0.711],[3.147,-0.714],[3.158,-0.708],[3.177,-0.689],[3.216,-0.619],[3.241,-0.594],[3.279,-0.584],[3.384,-0.584],[3.39,-0.59],[3.412,-0.59],[3.417,-0.584],[3.423,-0.59],[4.09,-0.592],[4.095,-0.587],[5.726,-0.593],[5.731,-0.588],[5.831,-0.588],[5.858,-0.599],[5.925,-0.67],[5.936,-0.665],[5.955,-0.684],[5.955,-0.7],[5.997,-0.736],[6.036,-0.753],[6.13,-0.764],[6.135,-0.769],[6.179,-0.77],[6.185,-0.775],[6.335,-0.781],[6.34,-0.787],[6.662,-0.793],[6.667,-0.788],[6.845,-0.789],[6.85,-0.783],[7.011,-0.778],[7.016,-0.773],[7.061,-0.773],[7.066,-0.768],[7.161,-0.757],[7.205,-0.741],[7.269,-0.684],[7.344,-0.599],[7.372,-0.589],[8.194,-0.592],[8.199,-0.586],[8.333,-0.587],[8.338,-0.592],[8.677,-0.594],[8.683,-0.588],[8.722,-0.588],[8.733,-0.594],[8.739,-0.588],[10.405,-0.589],[10.424,-0.576],[10.458,-0.505],[10.469,-0.444],[10.475,-0.439],[10.48,-0.379],[10.486,-0.373],[10.486,-0.34],[10.491,-0.335],[10.497,-0.225],[10.503,-0.22],[10.503,-0.138],[10.508,-0.132],[10.508,0.131],[10.503,0.136],[10.497,0.284],[10.491,0.29],[10.491,0.333],[10.486,0.339],[10.475,0.438],[10.441,0.547],[10.424,0.575],[10.405,0.588],[9.808,0.59],[9.802,0.585],[9.719,0.585],[9.713,0.59],[7.355,0.591],[7.205,0.739],[7.161,0.756],[7.066,0.767],[7.061,0.772],[7.016,0.773],[7.011,0.778],[6.944,0.778],[6.939,0.784],[6.551,0.796],[6.529,0.785],[6.34,0.785],[6.335,0.78],[6.185,0.775],[6.179,0.769],[6.135,0.769],[6.13,0.764],[6.036,0.753],[5.997,0.737],[5.955,0.702],[5.955,0.685],[5.936,0.666],[5.925,0.672],[5.858,0.601],[5.831,0.59],[3.423,0.591],[3.417,0.586],[3.412,0.592],[3.39,0.592],[3.384,0.586],[3.257,0.586],[3.241,0.592],[3.216,0.617],[3.177,0.687],[3.158,0.706],[3.147,0.712],[3.111,0.709],[3.111,0.802],[3.095,0.802],[3.095,0.835],[3.054,0.908],[2.822,0.909],[2.8,0.898],[2.707,0.876],[2.674,0.86],[2.668,0.866],[2.657,0.86],[2.624,0.866],[2.597,0.877],[2.564,0.877],[2.558,0.888],[2.542,0.882],[2.465,0.91],[2.459,0.904],[2.234,0.905],[2.228,0.894],[2.212,0.894],[2.173,0.851],[2.168,0.867],[2.102,0.867],[2.096,0.862],[2.036,0.862],[2.03,0.856],[2.025,0.873],[1.981,0.873],[1.975,0.867],[1.827,0.868],[1.821,0.873],[1.81,0.868],[1.794,0.873],[1.788,0.868],[0.581,0.871],[0.575,0.86],[0.57,0.871],[0.559,0.866],[0.548,0.871],[0.499,0.871],[0.488,0.86],[0.411,0.871],[0.405,0.866],[0.345,0.866],[0.34,0.861],[0.296,0.861],[0.29,0.855],[0.247,0.855],[0.241,0.85],[0.23,0.855],[0.121,0.856],[0.115,0.85],[0.049,0.84],[0,0.818],[-0.016,0.818],[-0.049,0.802],[-0.074,0.772],[-0.101,0.718],[-0.14,0.588],[-0.151,0.507],[-0.156,0.501],[-0.156,0.469],[-0.162,0.463],[-0.162,0.431],[-0.167,0.425],[-0.172,0.338],[-0.178,0.333],[-0.183,0.192],[-0.189,0.187],[-0.189,0.018]],"scaleRefs":["primary-arms-slx-1-6x24-gen-iv.tube_od","primary-arms-slx-1-6x24-gen-iv.length"],"inputs":{"primary-arms-slx-1-6x24-gen-iv.length":10.4,"primary-arms-slx-1-6x24-gen-iv.tube_od":1.1811023622047243},"tolerance":0.004,"photo":"references/primary-arms-slx-1-6x24-gen-iv d9806411659f (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_03.jpg (the Aurora 5.56 yard sibling: the same body), right side: the turned body)","method":"luminance < 200, largest piece, holes filled; the turned body alone: at each column the smaller of the dark run's reach above and below the tube's axis, taken both ways; scale from primary-arms-slx-1-6x24-gen-iv.tube_od = 1.1811 in, the tube's own width column by column: 216.7 px over columns 760–980, 216.8 px over columns 990–1210, 216.4 px over columns 1505–1760, 215.5 px over columns 1770–2035; a line through them (rms 0.27 px) changes -0.6% from column 760 to 2035, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 183.4 px/in there. The axis is the tube's centre line (tilt -0.19°, rms 0.08 px). Lengths then scaled by 1.0140 so that the end faces are primary-arms-slx-1-6x24-gen-iv.length = 10.4 in apart: at the tube's scale they read 10.256 (-1.4%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.106 in over radius 0.588 (rms 0.001), the rear end's rim sags 0.190 in over radius 0.855 (rms 0.002); origin at column 161 of the photo, on the tube's axis; Douglas-Peucker at 0.004 in with the extremes kept: 263 points (IoU 0.999 with the full outline) (tools/trace.py)","via":"harvest","note":"The scope's body of revolution from the right: the diopter ring, the eyepiece, the magnification ring, the main tube, the turret saddle, and the straight front tube to the objective's face. Under the elevation turret and the throw lever it is what shows below the axis. The magnification ring's and the diopter ring's lugs show in it as teeth: the model turns each ring at its lugs' tops and cuts the lugs."},"turret":{"plane":"xy","origin":"on the optical axis at the eyepiece's rear face (the right-side photo's column 161.0, where its end face reads zero behind its rim's arc): the scope's frame","offset":{},"points":[[5.944,1.176],[5.944,1.111],[5.977,1.067],[5.977,1.045],[5.955,1.013],[5.944,1.007],[5.944,0.958],[5.977,0.92],[5.977,0.794],[5.983,0.789],[5.986,0.743],[6.036,0.764],[6.13,0.775],[6.135,0.78],[6.179,0.78],[6.185,0.786],[6.335,0.791],[6.34,0.796],[6.529,0.796],[6.551,0.807],[6.662,0.806],[6.667,0.801],[6.845,0.8],[6.85,0.795],[6.939,0.795],[6.944,0.789],[7.061,0.783],[7.066,0.778],[7.161,0.767],[7.222,0.739],[7.23,0.747],[7.23,0.922],[7.263,0.955],[7.258,0.966],[7.263,0.971],[7.263,0.999],[7.23,1.048],[7.23,1.07],[7.258,1.102],[7.258,1.168],[7.188,1.215],[7.161,1.22],[7.094,1.204],[7.1,1.22],[7.039,1.22],[7.033,1.226],[7.028,1.22],[7.022,1.226],[6.817,1.226],[6.811,1.232],[6.495,1.232],[6.49,1.227],[6.191,1.228],[6.185,1.222],[6.113,1.222],[6.119,1.211],[6.157,1.211],[6.163,1.217],[6.407,1.222],[6.407,1.216],[6.324,1.216],[6.304,1.208],[6.335,1.206],[6.335,1.2],[6.096,1.206],[6.052,1.217],[6.013,1.217],[6.002,1.212]],"scaleRefs":["primary-arms-slx-1-6x24-gen-iv.tube_od","primary-arms-slx-1-6x24-gen-iv.length"],"inputs":{"primary-arms-slx-1-6x24-gen-iv.length":10.4,"primary-arms-slx-1-6x24-gen-iv.tube_od":1.1811023622047243},"tolerance":0.004,"photo":"references/primary-arms-slx-1-6x24-gen-iv d9806411659f (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_03.jpg (the Aurora 5.56 yard sibling: the same body), right side: the elevation turret)","method":"luminance < 200, largest piece, holes filled; what the silhouette has above the turned body, in columns 1225–1495; scale from primary-arms-slx-1-6x24-gen-iv.tube_od = 1.1811 in, the tube's own width column by column: 216.7 px over columns 760–980, 216.8 px over columns 990–1210, 216.4 px over columns 1505–1760, 215.5 px over columns 1770–2035; a line through them (rms 0.27 px) changes -0.6% from column 760 to 2035, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 183.4 px/in there. The axis is the tube's centre line (tilt -0.19°, rms 0.08 px). Lengths then scaled by 1.0140 so that the end faces are primary-arms-slx-1-6x24-gen-iv.length = 10.4 in apart: at the tube's scale they read 10.256 (-1.4%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.106 in over radius 0.588 (rms 0.001), the rear end's rim sags 0.190 in over radius 0.855 (rms 0.002); origin at column 161 of the photo, on the tube's axis; Douglas-Peucker at 0.004 in with the extremes kept: 68 points (IoU 0.993 with the full outline) (tools/trace.py)","via":"harvest","note":"The capped elevation turret above the saddle, from the side: turned about its own vertical axis. Its two rows of lugs show at its edges as teeth."},"lever":{"plane":"xy","origin":"on the optical axis at the eyepiece's rear face (the right-side photo's column 161.0, where its end face reads zero behind its rim's arc): the scope's frame","offset":{},"points":[[2.28,1.592],[2.28,0.989],[2.349,0.915],[2.459,0.915],[2.47,0.92],[2.542,0.893],[2.558,0.898],[2.569,0.888],[2.597,0.888],[2.652,0.871],[2.668,0.876],[2.674,0.871],[2.707,0.887],[2.8,0.909],[2.822,0.92],[3.043,0.919],[3.029,0.949],[3.054,0.941],[3.062,0.949],[3.062,0.96],[3.056,0.965],[3.056,0.992],[3.004,1.039],[2.996,1.036],[3.007,1.025],[3.004,1.017],[2.946,1.069],[2.949,1.082],[2.828,1.105],[2.822,1.11],[2.795,1.11],[2.767,1.121],[2.74,1.121],[2.734,1.127],[2.657,1.138],[2.652,1.143],[2.63,1.143],[2.624,1.149],[2.597,1.149],[2.536,1.17],[2.506,1.2],[2.489,1.244],[2.495,1.581],[2.489,1.603],[2.47,1.611],[2.322,1.611],[2.316,1.606],[2.305,1.611],[2.289,1.606]],"scaleRefs":["primary-arms-slx-1-6x24-gen-iv.tube_od","primary-arms-slx-1-6x24-gen-iv.length"],"inputs":{"primary-arms-slx-1-6x24-gen-iv.length":10.4,"primary-arms-slx-1-6x24-gen-iv.tube_od":1.1811023622047243},"tolerance":0.004,"photo":"references/primary-arms-slx-1-6x24-gen-iv d9806411659f (Primary Arms PA-SLX-1-6X24S-AUR-5Y6_03.jpg (the Aurora 5.56 yard sibling: the same body), right side: the throw lever)","method":"luminance < 200, largest piece, holes filled; what the silhouette has above the turned body, in columns 555–735 (the largest of 2 pieces); scale from primary-arms-slx-1-6x24-gen-iv.tube_od = 1.1811 in, the tube's own width column by column: 216.7 px over columns 760–980, 216.8 px over columns 990–1210, 216.4 px over columns 1505–1760, 215.5 px over columns 1770–2035; a line through them (rms 0.27 px) changes -0.6% from column 760 to 2035, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 183.4 px/in there. The axis is the tube's centre line (tilt -0.19°, rms 0.08 px). Lengths then scaled by 1.0140 so that the end faces are primary-arms-slx-1-6x24-gen-iv.length = 10.4 in apart: at the tube's scale they read 10.256 (-1.4%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.106 in over radius 0.588 (rms 0.001), the rear end's rim sags 0.190 in over radius 0.855 (rms 0.002); origin at column 161 of the photo, on the tube's axis; Douglas-Peucker at 0.004 in with the extremes kept: 49 points (IoU 0.992 with the full outline) (tools/trace.py)","via":"harvest","note":"The magnification ring's throw lever from the right, at 1x: a fin standing on its dovetail on top of the ring, its top hooked toward the eyepiece."},"plan":{"plane":"xz","origin":"on the optical axis at the eyepiece's rear face (the manual photo's column 690, where its end face reads zero behind its rim's arc)","offset":{},"points":[[-0.129,0.132],[-0.129,-0.126],[-0.113,-0.142],[-0.113,-0.4],[-0.098,-0.415],[-0.098,-0.552],[-0.083,-0.568],[-0.083,-0.659],[-0.068,-0.674],[-0.068,-0.735],[-0.053,-0.75],[-0.053,-0.781],[-0.038,-0.796],[-0.038,-0.811],[-0.015,-0.834],[0.03,-0.834],[0.045,-0.85],[0.091,-0.85],[0.106,-0.865],[0.227,-0.866],[0.242,-0.851],[0.257,-0.851],[0.288,-0.821],[0.325,-0.844],[0.333,-0.867],[0.409,-0.867],[0.424,-0.883],[1.546,-0.89],[1.561,-0.875],[2.122,-0.879],[2.138,-0.894],[2.153,-0.879],[2.29,-0.88],[2.305,-0.865],[2.35,-0.926],[2.578,-0.928],[2.594,-0.913],[2.639,-0.913],[2.685,-0.883],[2.73,-0.883],[2.746,-0.868],[2.791,-0.868],[2.806,-0.884],[2.822,-0.869],[2.898,-0.915],[2.928,-0.915],[2.943,-0.93],[2.959,-0.915],[3.172,-0.917],[3.194,-0.894],[3.225,-0.818],[3.24,-0.803],[3.24,-0.788],[3.225,-0.772],[3.225,-0.726],[3.24,-0.711],[3.24,-0.681],[3.286,-0.635],[3.286,-0.62],[3.309,-0.582],[3.324,-0.597],[3.507,-0.599],[3.522,-0.583],[3.537,-0.599],[3.842,-0.601],[3.857,-0.586],[5.2,-0.594],[5.215,-0.579],[5.23,-0.595],[5.246,-0.579],[5.261,-0.595],[5.521,-0.597],[5.536,-0.581],[5.903,-0.584],[6.064,-0.745],[6.033,-0.791],[6.048,-0.806],[6.033,-0.822],[6.033,-0.867],[6.048,-0.883],[6.018,-0.913],[6.018,-0.959],[6.033,-0.974],[6.018,-0.99],[6.018,-1.005],[6.048,-1.036],[6.048,-1.066],[6.018,-1.097],[6.018,-1.173],[6.064,-1.219],[6.056,-1.242],[6.025,-1.242],[6.018,-1.25],[6.018,-1.341],[6.025,-1.349],[6.087,-1.35],[6.102,-1.365],[6.27,-1.366],[6.285,-1.382],[6.975,-1.387],[6.99,-1.371],[7.159,-1.373],[7.174,-1.357],[7.251,-1.358],[7.274,-1.335],[7.274,-1.259],[7.251,-1.235],[7.235,-1.251],[7.228,-1.243],[7.228,-1.212],[7.251,-1.205],[7.274,-1.182],[7.274,-1.105],[7.243,-1.075],[7.243,-1.044],[7.274,-1.014],[7.274,-0.906],[7.243,-0.891],[7.243,-0.723],[7.281,-0.7],[7.297,-0.7],[7.304,-0.677],[7.389,-0.593],[7.818,-0.596],[7.834,-0.581],[7.911,-0.581],[7.926,-0.597],[7.941,-0.582],[10.434,-0.598],[10.458,-0.575],[10.458,-0.56],[10.473,-0.544],[10.473,-0.514],[10.488,-0.498],[10.488,-0.452],[10.504,-0.437],[10.504,-0.345],[10.519,-0.33],[10.519,-0.161],[10.55,-0.146],[10.55,0.069],[10.519,0.085],[10.519,0.3],[10.504,0.315],[10.504,0.392],[10.488,0.407],[10.488,0.469],[10.473,0.484],[10.473,0.515],[10.458,0.53],[10.458,0.546],[10.419,0.584],[8.079,0.597],[8.064,0.582],[8.049,0.597],[7.957,0.598],[7.941,0.583],[7.926,0.598],[7.864,0.598],[7.849,0.583],[7.834,0.583],[7.818,0.598],[7.803,0.583],[7.788,0.583],[7.772,0.599],[7.757,0.599],[7.742,0.584],[7.711,0.584],[7.696,0.599],[7.496,0.6],[7.481,0.585],[7.419,0.585],[7.404,0.601],[7.389,0.585],[7.266,0.709],[7.243,0.716],[7.243,0.9],[7.258,0.915],[7.243,0.931],[7.266,0.938],[7.289,0.961],[7.289,1.007],[7.243,1.053],[7.243,1.068],[7.289,1.114],[7.289,1.175],[7.266,1.183],[7.235,1.214],[7.174,1.214],[7.159,1.23],[7.113,1.23],[7.097,1.215],[7.051,1.215],[7.036,1.23],[7.021,1.23],[7.005,1.215],[6.944,1.215],[6.929,1.231],[6.485,1.233],[6.469,1.218],[6.454,1.218],[6.439,1.233],[6.301,1.234],[6.285,1.219],[6.071,1.22],[6.025,1.189],[5.995,1.189],[5.987,1.182],[5.987,1.105],[6.018,1.075],[6.018,1.044],[5.987,0.998],[5.987,0.952],[6.018,0.937],[6.018,0.769],[6.033,0.753],[6.033,0.723],[6.048,0.707],[6.025,0.685],[5.979,0.685],[5.903,0.594],[5.184,0.597],[5.169,0.582],[5.154,0.598],[4.94,0.599],[4.925,0.584],[3.309,0.592],[3.255,0.646],[3.255,0.661],[3.225,0.707],[3.225,0.768],[3.24,0.783],[3.225,0.799],[3.21,0.845],[3.156,0.913],[2.913,0.915],[2.898,0.9],[2.852,0.9],[2.822,0.869],[2.776,0.87],[2.761,0.854],[2.746,0.855],[2.73,0.87],[2.67,0.87],[2.639,0.901],[2.609,0.901],[2.594,0.916],[2.335,0.918],[2.312,0.895],[2.305,0.857],[2.29,0.872],[1.257,0.878],[1.242,0.862],[1.227,0.878],[1.106,0.878],[1.091,0.863],[0.575,0.866],[0.56,0.881],[0.545,0.866],[0.378,0.867],[0.363,0.852],[0.333,0.852],[0.303,0.822],[0.272,0.822],[0.265,0.845],[0.242,0.868],[0.227,0.852],[0.121,0.853],[0.106,0.838],[0.03,0.838],[0.015,0.823],[-0.015,0.823],[-0.053,0.785],[-0.053,0.755],[-0.068,0.74],[-0.068,0.694],[-0.083,0.679],[-0.083,0.588],[-0.098,0.573],[-0.098,0.451],[-0.113,0.436],[-0.113,0.147]],"scaleRefs":["primary-arms-slx-1-6x24-gen-iv.tube_od","primary-arms-slx-1-6x24-gen-iv.length"],"inputs":{"primary-arms-slx-1-6x24-gen-iv.length":10.4,"primary-arms-slx-1-6x24-gen-iv.tube_od":1.1811023622047243},"tolerance":0.006,"photo":"references/primary-arms-slx-1-6x24-gen-iv f2c0f052f001 (Primary Arms, SLx 1-6x24 Second Focal Plane Optic Manual, the sheet numbered 4: the scope from above, 700 x 174 px)","method":"luminance < 200, largest piece, holes filled; scale from primary-arms-slx-1-6x24-gen-iv.tube_od = 1.1811 in, the tube's own width column by column: 77.0 px over columns 14–100, 77.0 px over columns 106–196, 77.3 px over columns 308–384, 77.3 px over columns 390–462; a line through them (rms 0.09 px) changes +0.6% from column 14 to 462, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 350)/width, the lens's axis taken to meet the image at column 350; 65.4 px/in there. The axis is the tube's centre line (tilt +0.34°, rms 0.10 px). Lengths then scaled by 0.9998 so that the end faces are primary-arms-slx-1-6x24-gen-iv.length = 10.4 in apart: at the tube's scale they read 10.402 (+0.0%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.136 in over radius 0.586 (rms 0.010), the rear end's rim sags 0.124 in over radius 0.853 (rms 0.005); origin at column 690 of the photo, on the tube's axis; Douglas-Peucker at 0.006 in with the extremes kept: 282 points (IoU 0.999 with the full outline); checks: width 10.679 ± 0.057; the min end's face: the silhouette's tip at -0.123 less its rim's arc, 0.124 in of sag at radius 0.852557 (the end is seen from 8.3° off square; arc fitted over 121 rows, rms 0.005) 0.001 ± 0.023; the max end's face: the silhouette's tip at 10.537 less its rim's arc, 0.136 in of sag at radius 0.586162 (the end is seen from 13.1° off square; arc fitted over 121 rows, rms 0.010) 10.401 ± 0.042 (tools/trace.py)","via":"harvest","note":"The whole scope from above, no throw lever fitted: the windage turret toward +z (the scope's right), the illumination knob toward -z, each in profile. At 66 px to the inch an edge is good to about 0.02 in."}},"gaps":[{"what":"A view from either end, or Primary Arms' own dimensioned drawing","need":"neither manual has a drawing and no page read has an end view: the magnification ring's and the diopter ring's lugs are counted on the half turn each side view shows, and the windage cap and the illumination knob are placed by the manual's small photo from above (66 px to the inch)"},{"what":"A straight side view of this scope itself (the NOVA)","need":"its own gallery is four three-quarter views: the outlines are traced from the Aurora 5.56 yard sibling's two side views, the same body by Primary Arms' pages"},{"what":"How deep the glass sits at each end, the diopter ring's pockets, the coin slot, and how far the plug on the saddle stands off","need":"a close photo of each with a scale: the depths drawn are assumed and listed"},{"what":"A reviewer's own weighing; whether the throw lever is in Primary Arms' 17.85 oz","need":"a scale: the maker's two figures (17.85 oz in the manual, 17.9 oz on the page) are one weight, and neither says whether the lever is on"},{"what":"Black matched under the app's light (it is the optics' placeholder)","need":"make color-match against the black product photos, as the other black optics"}]},"primary-arms-slx-cantilever-30mm-mount":{"id":"primary-arms-slx-cantilever-30mm-mount","name":"SLx Cantilever 30mm Mount - 1.5\"","manufacturer":"Primary Arms","sku":"PA-SLX-CM-30-1.5","url":"https://www.primaryarms.com/primary-arms-slx-cantilever-30mm-mount-1-5in","category":"scope_mount","description":"Primary Arms' one-piece cantilever scope mount for a 30 mm tube: \"6061 Aluminum construction\", \"Steel hardware\", \"Three bolt design for increased strength\", \"Dual recoil lugs\", \"1.5\" Optical centerline\". The scope slides in its two rings before their caps are tightened (\"Rings - 16-18 in. lbs.\"), which sets the eye relief; the clamp's three cross bolts lie in three of the rail's slots (\"Base - 30-35 in. lbs.\").","weight":"primary-arms-slx-cantilever-30mm-mount.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":[0,0,0],"note":"Mount frame: on the rail's top under the rear cross bolt, +x forward. That bolt lies in the slot the build names; the middle one is three slots ahead and the front one six."},"rings":{"origin":["({.ring_rear_x} + {.ring_front_x}) / 2","{.optical_axis_above_rail}",0],"note":"On the rings' axis midway between the two rings: where a scope's saddle is put at position 0."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":0,"clamp_front":"=2 * {.clamp_bolt_spacing}","cross_front":"=2 * {.clamp_bolt_spacing}"},"flips":false,"note":"Three cross bolts three slots apart (\"Three bolt design\", \"3 cross bolt lugs\"; \"Base - 30-35 in. lbs.\"): it is clamped from the rear bolt, in the slot the build names, to the front one six slots ahead. A cantilever: the rear ring stands over the clamp and the front ring 1.8 in ahead of the front bolt, so the clamp stays on the receiver with the scope forward (Primary Arms' guide: \"cantilever mounts should be placed as far forward on the receiver as possible without bridging the mount onto the handguard\"). Which end is the front rests on that: no photo of this mount on a rifle is on file."},"rings":{"type":"scope_rings","role":"rings","anchor":"rings","params":{"diameter":"={.ring_bore}","rear_ring":"=({.ring_rear_x} - {.ring_front_x}) / 2","front_ring":"=({.ring_front_x} - {.ring_rear_x}) / 2","ring_length":"={.ring_length}"},"flips":false,"note":"Two rings bored 30 mm (\"For 30mm scope tubes\"), 3.60 in apart middle to middle and 0.765 long each: 2.83 in between their faces for a scope's saddle. Four cap screws to a ring (\"Rings - 16-18 in. lbs.\")."}},"materials":{"body":{"label":"Mount","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized_matte","color":"placeholder-black","sku":"PA-SLX-CM-30-1.5","source":"https://www.primaryarms.com/primary-arms-slx-cantilever-30mm-mount-1-5in"}},"default":"black","note":"Sold in black only (Primary Arms' table: \"Color Black\", \"Finish Hardcoat Anodized\"; no other colour on any page read). Drawn as the catalog's matte anodize (`anodized_matte`): its four photos have an even matte grain with no bright line on any edge, as Primary Arms' scopes have. Piece by piece on the four photos (2026-10-13): both rings (caps and lower halves), their feet, the arm, the base with its three bosses and the clamp bar are the one matte black; the cross bolts' heads and ends and the cap screws are a glossier black (the `hardware` slot). Black on anodize isn't fitted to a photo: the placeholder the other black optics and mounts use. The white PRIMARY ARMS on the arm's left side isn't drawn."},"hardware":{"label":"Cross bolts and cap screws","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The three cross bolts (Torx heads in the clamp bar's counterbores on the right, their threaded ends in the left side's bosses) and the eight ring cap screws at the bottoms of their holes. Primary Arms: \"Steel hardware\"; their coat isn't said. In the photos the heads are a deeper, glossier black than the mount and the bolts' ends show bright thread: drawn as dark steel, the placeholder black (a black on steel isn't fitted to a photo)."}},"components":{"body":{"label":"Mount","material":"body"},"hardware":{"label":"Cross bolts and cap screws","material":"hardware"}},"geometry":{"model":"primary-arms-slx-cantilever-30mm-mount.glb","components":{},"approximations":["The mount is its own left side view (the one view that is square on and level), with its widths read through a camera fitted to the bores in the front-right view: the rings 1.53 in across their side flats, the arm a 0.75 in beam, the clamp bar's face 0.68 in out from the rail's middle. No view is square across it: the rings' top flat is worked out from 45 degree chamfers, and the left side is drawn as far out as the right reads.","Each ring is an octagon in section (its cap's chamfers and its lower half's both taken at 45 degrees) with its corners chamfered in plan and its top bevelled at each end as the side outline has it, bored through at the tube it is for and closed on it: the split between cap and lower half is a groove as wide as the photo's gap and as deep (assumed), with no gap through. The four cap screws stand in round holes straight down through the cap's chamfers, each hole standing against the side flat's plane, their heads drawn as plain discs on a floor 0.075 in under the hole's middle as the side sees it (assumed: no lower, or the hole would open into the bore). The caps' real shoulders under the screws, flatter than 45 degrees under a curve up to the top flat, aren't drawn; the two pockets under them in each side of the lower half are cut 0.06 in into the chamfer (assumed).","The arm and the rings' feet are the side outline at the arm's width, with the long pocket in each side and the slanted pocket under the rear ring cut blind to the depth one oblique gives (0.19 in, a weak reading); the right side's pockets are drawn as the left's mirrored. The two ribs the rear ring's foot shows from the front right aren't drawn apart.","The base is the outline below its top face: the fixed side on the left with its three bosses and the gaps cut up between them, the separate clamp bar on the right drawn as a bar of its read length and the base's height, 0.25 in thick (assumed), its face flat in a pad round each of three counterbores and cut back between and beyond the pads by a facet along its upper edge and one along its lower, each as tall as the right view has it and 0.08 in deep at the edge (assumed); each cross bolt's head is a disc flush in its counterbore with its six-lobed socket as a twelve-cornered star between the two circles the right view gives (the head's height, the socket's depth, the depth of the recess round the bolt's other end and how far that end stands under the boss's face are assumed). Under them the rail's place is the rail's own head in section (MIL-STD-1913's) from the rail's top down to the lower gauge line, and plain walls as wide apart as the rail's top below that, not the jaws' hooks.","The \"dual recoil lugs\" Primary Arms states are under the base, which no photo shows: not drawn. The three cross bolts are drawn in the slots as the lugs they also are.","Its metal as drawn comes to the published weight within a tenth: the part's test holds it."],"ledger":["primary-arms-slx-cantilever-30mm-mount.optical_axis_above_rail","primary-arms-slx-cantilever-30mm-mount.ring_bore","primary-arms-slx-cantilever-30mm-mount.ring_spacing","primary-arms-slx-cantilever-30mm-mount.ring_rear_x","primary-arms-slx-cantilever-30mm-mount.ring_front_x","primary-arms-slx-cantilever-30mm-mount.ring_length","primary-arms-slx-cantilever-30mm-mount.ring_width","primary-arms-slx-cantilever-30mm-mount.ring_top_above_axis","primary-arms-slx-cantilever-30mm-mount.arm_width","primary-arms-slx-cantilever-30mm-mount.clamp_bolt_spacing","primary-arms-slx-cantilever-30mm-mount.clamp_bar_outer_z","primary-arms-slx-cantilever-30mm-mount.mount_length"]},"profiles":{"side":{"plane":"xy","origin":"on the rings' axis above the rear cross bolt; the app lowers it by the axis's height above the rail, to the mount's frame","offset":{"y":"optical_axis_above_rail"},"points":[[-0.55,-1.372],[-0.548,-1.499],[-0.349,-1.724],[-0.327,-1.743],[-0.306,-1.751],[0.221,-1.751],[0.239,-1.746],[0.286,-1.704],[0.901,-1.704],[0.945,-1.743],[0.965,-1.751],[1.433,-1.751],[1.456,-1.743],[1.498,-1.702],[2.115,-1.704],[2.152,-1.738],[2.175,-1.751],[2.715,-1.751],[2.919,-1.547],[2.981,-1.5],[3.028,-1.477],[3.428,-1.384],[4.064,-1.247],[4.175,-1.216],[4.22,-1.165],[4.38,-0.933],[4.553,-0.698],[4.561,-0.667],[4.582,-0.279],[4.579,-0.028],[4.553,-0.003],[4.579,0.026],[4.582,0.248],[4.574,0.344],[4.564,0.359],[4.561,0.38],[4.548,0.53],[4.535,0.584],[4.454,0.668],[4.433,0.673],[3.873,0.671],[3.791,0.587],[3.802,0.509],[3.796,0.506],[3.796,0.53],[3.79,0.541],[3.781,0.525],[3.765,0.129],[3.765,-0.021],[3.778,-0.034],[3.781,-0.052],[3.763,-0.072],[3.768,-0.444],[3.776,-0.576],[3.783,-0.618],[3.783,-0.721],[3.768,-0.773],[3.75,-0.798],[3.718,-0.826],[3.674,-0.844],[3.547,-0.862],[1.971,-1.056],[1.728,-1.079],[1.009,-1.076],[0.96,-1.063],[0.907,-1.018],[0.894,-0.997],[0.881,-0.954],[0.884,-0.897],[0.902,-0.855],[1,-0.713],[1.008,-0.682],[1.013,-0.69],[1.013,-0.656],[1.026,-0.643],[1.026,-0.628],[1.02,-0.637],[1.016,-0.631],[1.029,-0.618],[1.031,-0.584],[1.026,-0.576],[1.031,-0.574],[1.025,-0.572],[1.022,-0.593],[1.018,-0.571],[1.029,-0.463],[1.034,-0.121],[1.039,-0.124],[1.034,-0.111],[1.039,-0.088],[1.016,-0.049],[1.042,-0.013],[1.037,0.274],[1.024,0.509],[1.013,0.553],[1.003,0.522],[0.998,0.473],[0.985,0.026],[0.965,0.001],[0.956,0],[0.977,0.028],[0.977,0.3],[0.99,0.372],[0.998,0.509],[1.003,0.558],[1.013,0.574],[1.011,0.587],[0.927,0.671],[0.356,0.671],[0.264,0.574],[0.248,0.491],[0.238,0.364],[0.225,0.344],[0.217,0.276],[0.217,0.026],[0.243,-0.003],[0.215,-0.026],[0.21,-0.049],[0.21,-0.344],[0.243,-0.853],[0.211,-0.901],[0.131,-0.955],[-0.417,-1.267],[-0.422,-1.275],[-0.448,-1.278],[-0.528,-1.322],[-0.545,-1.341]],"features":{"lower_pockets":[[[4.527,-0.305],[4.32,-0.305],[4.32,-0.419],[4.328,-0.458],[4.351,-0.492],[4.384,-0.514],[4.423,-0.522],[4.463,-0.514],[4.497,-0.492],[4.519,-0.458],[4.527,-0.419]],[[4.074,-0.305],[3.867,-0.305],[3.867,-0.419],[3.875,-0.458],[3.897,-0.492],[3.931,-0.514],[3.971,-0.522],[4.01,-0.514],[4.043,-0.492],[4.066,-0.458],[4.074,-0.419]],[[0.928,-0.305],[0.721,-0.305],[0.721,-0.419],[0.729,-0.458],[0.751,-0.492],[0.785,-0.514],[0.825,-0.522],[0.864,-0.514],[0.898,-0.492],[0.92,-0.458],[0.928,-0.419]],[[0.475,-0.305],[0.268,-0.305],[0.268,-0.419],[0.276,-0.458],[0.298,-0.492],[0.332,-0.514],[0.371,-0.522],[0.411,-0.514],[0.445,-0.492],[0.467,-0.458],[0.475,-0.419]]],"arm_pocket":[[[4.126,-1.102],[4.16,-1.088],[4.187,-1.064],[4.205,-1.033],[4.213,-0.997],[4.21,-0.961],[4.196,-0.927],[4.172,-0.9],[4.14,-0.882],[4.105,-0.874],[4.069,-0.877],[3.056,-1.135],[3.022,-1.15],[2.995,-1.174],[2.976,-1.205],[2.968,-1.241],[2.972,-1.277],[2.986,-1.31],[3.01,-1.338],[3.042,-1.356],[3.077,-1.364],[3.113,-1.361]]],"neck_pocket":[[[0.683,-0.933],[0.708,-0.905],[0.724,-0.871],[0.728,-0.834],[0.72,-0.798],[0.702,-0.766],[0.674,-0.741],[0.64,-0.725],[0.603,-0.721],[0.567,-0.729],[0.535,-0.747],[0.173,-1.036],[0.148,-1.064],[0.132,-1.098],[0.128,-1.135],[0.136,-1.171],[0.154,-1.203],[0.182,-1.228],[0.216,-1.244],[0.253,-1.248],[0.289,-1.24],[0.321,-1.222]]],"arches":[[[2.144,-1.755],[1.914,-1.535],[1.671,-1.535],[1.441,-1.755]],[[0.949,-1.755],[0.719,-1.535],[0.476,-1.535],[0.246,-1.755]]]},"scaleRefs":["primary-arms-slx-cantilever-30mm-mount.ring_rear_x","primary-arms-slx-cantilever-30mm-mount.ring_front_x"],"inputs":{"primary-arms-slx-cantilever-30mm-mount.ring_front_x":4.197,"primary-arms-slx-cantilever-30mm-mount.ring_rear_x":0.598},"tolerance":0.004,"photo":"references/primary-arms-slx-cantilever-30mm-mount d0a5b183f1dc (Primary Arms PA-SLX-CM-30-1.5_02.jpg: the mount's left side, square on and level, 2200 x 1467)","method":"luminance < 200, largest piece, holes filled; frame from the reviewed holes front_ring, rear_ring (387.0 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.004 in with the extremes kept: 127 points (IoU 0.996 with the full outline); features through the same placement (lower_pockets: the two pockets in each ring's lower half, under the cap's screws: a flat top and a round foot, in the chamfer below the side flat; arm_pocket: the long blind pocket in the arm's side, a slot with round ends lying along the arm's slope; neck_pocket: the slanted blind pocket in the foot under the rear ring; arches: the gaps cut up into the fixed side between its three bosses, to just under the rail's top: the silhouette there is the clamp bar's, seen through them) (tools/trace.py)","via":"harvest","note":"The mount as its own left side shows it, turned to face +x: both rings (top flats, the bevels at their ends, the split), their feet, the arm sloping down to the base, the base's three bosses and its pointed rear end. Between the bosses the outline's foot is the clamp bar's on the far side, seen through the gaps."}},"gaps":[{"what":"Any published length (overall, ring spacing, ring width, forward reach)","need":"Primary Arms publishes none and no manual or drawing exists on a page read: every length rests on a camera fitted to the bores in an oblique photo, with a second one 1.1% from it, the rail's pitch 0.8% the other way and the 1.5 in height as its checks"},{"what":"A view square across the mount, from above or end on, and one of its underside","need":"none in Primary Arms' gallery: the widths are single readings through the fitted camera, the left side's reach, the clamp bar's thickness and the recoil lugs aren't read at all"},{"what":"A photo of it on a rifle or with a scope in it","need":"none found: which end is the front rests on its being a cantilever and on Primary Arms' guide"},{"what":"The scale to better than 1%","need":"a published length, or a view with a bore end on: the two cameras fitted to the bores read the rings 3.60 and 3.64 in apart, and three rail slots under the cross bolts would make them 3.57; 3.60 is used"},{"what":"The left side's widths (how far out the bosses' faces are)","need":"points picked on the rear-left view (ebcd0767a140) through its fitted camera, as the right side's were on the front-right view: drawn as far out as the right side reads"},{"what":"The cross bolts' and cap screws' sizes and drivers","need":"not published (Torx heads in the photos)"}]},"psa-stealth-stripped-lower":{"id":"psa-stealth-stripped-lower","name":"AR-15 \"Stealth\" Stripped Lower Receiver","manufacturer":"Palmetto State Armory","sku":"39296","url":"https://palmettostatearmory.com/psa-stealth-lower.html","category":"lower","description":"Palmetto State Armory's forged stripped lower with no logo: \"this lower features no rollmark on the left hand side, just the caliber, model and serial\". \"These forged lowers are quality made by a mil-spec contractor using 7075-T6 aluminum and are marked \"MULTI\" to accommodate most builds. Finish is Black Hardcoat Anodize per MIL-8625 Type 3 class 2.\" \"Serial Number prefix is \"PA\". Fire selector is marked \"Safe\" and \"Fire\".\" (its page, as saved 2026-10-12). No trigger guard: a separate one pins into its ears.","weight":"psa-stealth-stripped-lower.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"pins":{"origin":[0,0,0],"note":"The rifle frame origin."},"buffer_tube_mount":{"origin":[0,"{.buffer_axis_above_pin}",0],"x":[-1,0,0]},"magwell":{"origin":["{.magazine_seat_x}","{std.ar15.mag_catch_slot_bottom_y} + {std.ar15.mag_catch_slot_h}",0],"note":"Where a seated magazine hangs: x where its spine's rear face sits in the well (magazine_seat_x), y at the catch's upper face, which is the top of the slot the catch comes through (the Army's drawing). A magazine's own anchor is the upper edge of its catch notch, so each hangs by its own. The Army drawing's well and catch slot, as the catalog's other mil-spec lowers have it: this lower's left photo has the catch's hole within 0.003 in of the drawing's place, and no photo of a magazine seated in it is on file."},"grip_lug":{"origin":[0,"{.grip_seat_y}",0],"note":"The grip mount's datum: the face either side of the lug that a grip's flat top bears on, at the takedown pin's x: the Army drawing's, 1.318 below the deck (the left photo has the body's lower edge over the lug on it within a pixel)."},"trigger_guard":{"origin":["{.trigger_guard_front_x}","{.trigger_guard_front_y}",0],"x":["{.trigger_guard_front_x} - {.trigger_guard_rear_x}","{.trigger_guard_front_y} - {.trigger_guard_rear_y}",0],"note":"At the front ear hole, with the guard's x axis through the rear ear hole: a guard pins into both. The Army drawing's holes (the rear one read on the left photo within 0.012 in of it; the front one is in the right ear and isn't seen)."},"fcg":{"origin":["{.trigger_pin_x}","{.trigger_pin_y}",0],"note":"Trigger pin axis."},"lpk":{"origin":[0,0,"-{std.ar15.lower_body_width} / 2"],"note":"The body's left face (the TDP's width), level with the takedown pin: the controls' heads seat on it."},"selector":{"origin":["{std.ar15.selector_x}","{std.ar15.selector_y}",0],"note":"The selector's hole (the Army's drawing 8448608), on its axis at the receiver's mid-plane: a selector chosen on its own turns here (D86), its levers' inner faces on the body's two sides."}},"interfaces":{"receiver_pins":{"type":"ar15.upper_lower","role":"lower","anchor":"pins","params":{"pin_spacing":"={std.ar15.pin_spacing}"},"flips":false},"buffer_tube_mount":{"type":"ar15.buffer_tube_mount","role":"receiver","anchor":"buffer_tube_mount","params":{},"flips":false},"magwell":{"type":"ar15.magwell","role":"receiver","anchor":"magwell","params":{"family":"5.56"},"flips":false,"note":"A standard AR-15 magazine well: 'the AR-15 Stealth Lower Receiver', 'made by a mil-spec contractor', 'marked \"MULTI\" to accommodate most builds'; 'Caliber: Multi' (its page)."},"grip_lug":{"type":"ar15.grip_lug","role":"receiver","anchor":"grip_lug","params":{},"flips":false},"trigger_guard":{"type":"ar15.trigger_guard","role":"receiver","anchor":"trigger_guard","params":{},"flips":false},"fcg":{"type":"ar15.fcg","role":"receiver","anchor":"fcg","params":{"pin_diameter":"small-pin"},"flips":false,"note":"The page doesn't state the pins' size: it says the lowers are 'made by a mil-spec contractor', and the Army's drawing (8448608) has the hammer's and trigger's holes for .154 pins (std.ar15.fcg_pin_hole_d, .157). Its close-up photo bears that out: at the scale the selector's and trigger's holes set, the hammer's and trigger's rims are 0.159 and 0.151 across (fcg_pin_hole_d in the ledger), not a large pin's .170."},"lpk":{"type":"ar15.lpk","role":"receiver","anchor":"lpk","params":{},"flips":false},"selector":{"type":"ar15.selector","role":"receiver","anchor":"selector","params":{},"flips":false}},"materials":{"receiver":{"label":"Receiver","finish":"anodized","recolorable":true,"color":"placeholder-black","sheen":"matte","options":{"black":{"label":"Black Hardcoat Anodized","finish":"anodized","color":"placeholder-black","sheen":"matte","sku":"39296","source":"https://palmettostatearmory.com/psa-stealth-lower.html"}},"default":"black","note":"'Black Hardcoat Anodized'; 'Finish is Black Hardcoat Anodize per MIL-8625 Type 3 class 2' (its page, as the user saved it 2026-10-12). The one finish the page sells; unmatched (sealed black anodize). A stripped receiver: one piece, nothing of another colour on it."}},"components":{"receiver":{"label":"Receiver","material":"receiver"}},"geometry":{"model":"psa-stealth-stripped-lower.glb","components":{},"approximations":["Its only pictures are two of the LEFT side, 546 px square, from the page the user saved (the site refuses the reader): the whole receiver in one of them is about 59 px to the inch, so the outline is good to about 0.03 in. It is framed by its own takedown and pivot pin holes, and the frame was checked at five more of the Army drawing's holes (the selector's, trigger's, hammer's, the trigger guard's rear one and the magazine catch's): each within 0.025 in of the drawing's place, the furthest along within 0.002.","THE RIGHT SIDE IS NOT PHOTOGRAPHED ON FILE. What the model has there is the standard forging's, not this lower's own: the magazine catch's fence, the roll along the top of the well's right wall and where the right wall begins are the readings made on the catalog's forged mil-spec lower (the Workhorse's right photo, by the ledger), which the reference CAD model's forging and Bear Creek's lower have within a few hundredths; the button's pocket, the counterbore, the takedown hole's spotface and the trigger guard's front hole in the right ear are the Army drawing's and the reference model's. The page says only that these lowers are 'made by a mil-spec contractor'.","The grip's mount is the standard's: the face a grip bears on 1.318 below the deck and the lug at the drawing's .375 across, its rear face under the takedown pin, its sloped face 1.228 from the pin at 60 degrees, its flat .93 below the seat (the Army's drawing 8448608); the walls with the trigger guard's ears 0.659 across (the reference CAD model) and the ears .438 +.008 apart (the drawing); the rear underside the reference model's, an arc on the centre plane and a half-round across the body, so the seat's rear edge is a U (the left photo's silhouette there runs 0.01 to 0.026 in outside that arc all along, a pixel and a half at most). The left photo shows the lug whole under the body's edge and has it on the drawing's: its rear face at -0.095 (the drawing -0.075), its flat at -1.995 (-1.9995), its sloped face at 61.5 degrees (60), the ears' rear face at 1.16 to 1.18 (1.175), the seat's line at -1.07 (-1.0695). The ears' rear face is the drawing's too (1.175: where a grip's nose comes to; the outline has it from 1.160 at its top to 1.177 at its foot). Where the trigger's opening begins and the ears' own shape are the outline's; the walls step in square at the seat's level, where the reference model flares them over 0.15 in.","The underside above the trigger's opening is drawn on the grip seat's plane (-1.0695): the outline reads it at -1.085 ± 0.026, a pixel below, and the drawing has one surface there.","The traced outline at the TDP's body width (0.880), its magazine well's walls at 1.098 from each side's rear edge forward (on the left from the curved edge the left photo shows: straight down from the deck at 2.955, curving forward between Y -0.62 and -1.09 to 3.49), and the buffer tower's ring at 1.392 about the buffer axis, its top and its rear face the drawing's (the photo sees the ring from ahead: its silhouette tops out 0.03 above the drawing's and stands 0.065 behind the drawing's rear face).","The tower's bore through the ring and on along the trough between the walls' sweep, cut at the mil-spec receiver extension's OD (1.148): the thread it really has is larger by its depth, which isn't on file. The walls' sweep is drawn at the ring's width back to where the outline's sweep ends, stepping to the body's there, and rises to the ring's front face along the Army drawing's arc (.750 R, 8448608 sheet 1) and no higher. Its deck, from just behind the takedown pin to where its top turns down at the pivot lug, is the Army drawing's plane (.250 -.003 above the pins: std.ar15.deck_y), not the outline's own top edge (0.261 ± 0.05): the deck is the seat every upper sits on.","The inside a forged mil-spec lower has, from the Army's drawing 8448608 (D46): the fire-control pocket, the rear lug's slot, the safety detent's boss, the trigger slot and the magazine well with its spine slot, open from the deck to the mouth. Nothing of this lower's own inside is on file (no view into it).","The pivot lug as its two ears: the slot the upper's front lug goes in, the drawing's .500 across, cut through the lug ahead of the well's front face. How far down the slot runs into the well's front wall behind that face isn't on file: the wall is left whole between the ears.","The holes at the drawing's sizes and places: the takedown and pivot pins', the selector's, the hammer's and trigger's, the trigger guard's roll pin hole through both ears (each found on the left photo within 0.025 in of the drawing's) and, not seen, the guard's front hole and spotface in the right ear and the takedown hole's spotface on the right.","On the left, as the left photo has them where the drawing and the reference CAD model put them: the magazine catch's slot opening into the well, the catch hole through to the button's pocket (the photo: X 3.289, Y -0.564; the drawing 3.291, -0.565), the band down the well's wall (its edges at 3.98 and 4.57 to 4.62 on the photo; the model's 3.975 and 4.549) and the round boss the slot runs through, the bolt catch's two bosses (their outlines from this lower's photo, out to the TDP's face, drawn up to the deck: the photo has a bright line along their tops 0.04 in under it, which may be their tops or a chamfer's highlight, and can't say which at 59 px to the inch) and its slot and plunger hole.","Not drawn: the roll marks (PA-15, MULTI and the serial number on the well; PALMETTO STATE ARMORY, WEST COLUMBIA, S.C.; FIRE and SAFE: this lower has no logo), the two oblong pockets either side of the selector's hole on the left (the second picture shows them; how deep they are can't be read from a side view), the grip screw's hole in the lug, the pivot hole's countersink, the bore's thread and the buffer retainer's hole.","Edges broken at 0.02 in (the drawing's \"break corners .02 R\"); the well's flared lip and the takedown and pivot lugs' ears at the widths above.","Its weight is worked out from this model's metal (8.47 oz as 7075): the page states none."],"ledger":["psa-stealth-stripped-lower.bolt_catch_boss_bottom_y","psa-stealth-stripped-lower.bolt_catch_boss_front_x","psa-stealth-stripped-lower.bolt_catch_boss_rear_x","psa-stealth-stripped-lower.bolt_catch_gap_front_x","psa-stealth-stripped-lower.bolt_catch_gap_rear_x","psa-stealth-stripped-lower.buffer_axis_above_pin","psa-stealth-stripped-lower.fence_bottom_y","psa-stealth-stripped-lower.fence_corner_r","psa-stealth-stripped-lower.fence_front_x","psa-stealth-stripped-lower.fence_rear_x","psa-stealth-stripped-lower.fence_top_y","psa-stealth-stripped-lower.grip_mating_y","psa-stealth-stripped-lower.grip_seat_y","psa-stealth-stripped-lower.grip_shelf_top_x","psa-stealth-stripped-lower.hammer_pin_x","psa-stealth-stripped-lower.hammer_pin_y","psa-stealth-stripped-lower.magwell_front_x","psa-stealth-stripped-lower.magwell_wall_curve_bottom_y_left","psa-stealth-stripped-lower.magwell_wall_curve_top_y_left","psa-stealth-stripped-lower.magwell_wall_rear_x","psa-stealth-stripped-lower.magwell_wall_rear_x_left","psa-stealth-stripped-lower.magwell_wall_upper_rear_x_left","psa-stealth-stripped-lower.rear_behind_pin","psa-stealth-stripped-lower.selector_x","psa-stealth-stripped-lower.selector_y","psa-stealth-stripped-lower.tower_front_x","psa-stealth-stripped-lower.trigger_guard_front_x","psa-stealth-stripped-lower.trigger_guard_front_y","psa-stealth-stripped-lower.trigger_guard_rear_x","psa-stealth-stripped-lower.trigger_guard_rear_y","psa-stealth-stripped-lower.trigger_opening_top_y","psa-stealth-stripped-lower.trigger_pin_x","psa-stealth-stripped-lower.trigger_pin_y","psa-stealth-stripped-lower.well_roll_bottom_y","psa-stealth-stripped-lower.well_roll_crest_out","psa-stealth-stripped-lower.well_roll_front_x","psa-stealth-stripped-lower.well_roll_rear_round","psa-stealth-stripped-lower.well_roll_rear_x","std.ar15.bolt_catch_boss_out","std.ar15.bolt_catch_plunger_hole_d","std.ar15.bolt_catch_plunger_hole_depth","std.ar15.bolt_catch_plunger_hole_y","std.ar15.bolt_catch_slot_bottom_y","std.ar15.bolt_catch_slot_floor","std.ar15.bolt_catch_slot_front_x","std.ar15.bolt_catch_slot_width","std.ar15.bore_axis_y","std.ar15.buffer_tower_front_x","std.ar15.buffer_tower_od","std.ar15.deck_front_x","std.ar15.deck_y","std.ar15.fcg_pin_hole_d","std.ar15.fcg_pocket_corner_r","std.ar15.fcg_pocket_depth","std.ar15.fcg_pocket_front_x","std.ar15.fcg_pocket_length","std.ar15.fcg_pocket_width","std.ar15.front_lug_slot_width","std.ar15.grip_lug_depth","std.ar15.grip_lug_face_angle","std.ar15.grip_lug_face_from_pin","std.ar15.grip_lug_front_from_rear_face","std.ar15.grip_lug_length","std.ar15.grip_lug_width","std.ar15.grip_seat_below_deck","std.ar15.lower_body_width","std.ar15.mag_catch_boss_edge_r","std.ar15.mag_catch_boss_proud","std.ar15.mag_catch_boss_r","std.ar15.mag_catch_boss_x","std.ar15.mag_catch_cbore_d","std.ar15.mag_catch_cbore_depth","std.ar15.mag_catch_fence_out","std.ar15.mag_catch_hole_d","std.ar15.mag_catch_slot_bottom_y","std.ar15.mag_catch_slot_floor","std.ar15.mag_catch_slot_front_x","std.ar15.mag_catch_slot_h","std.ar15.mag_catch_slot_rear_x","std.ar15.mag_catch_x","std.ar15.mag_catch_y","std.ar15.mag_release_pocket_depth","std.ar15.mag_release_pocket_h","std.ar15.mag_release_pocket_w","std.ar15.magwell_band_bottom_y","std.ar15.magwell_band_front_x","std.ar15.magwell_band_proud","std.ar15.magwell_band_rear_x","std.ar15.magwell_band_side","std.ar15.magwell_box_length","std.ar15.magwell_corner_r","std.ar15.magwell_front_inner_x","std.ar15.magwell_length","std.ar15.magwell_outside_width","std.ar15.magwell_spine_slot_width","std.ar15.magwell_width","std.ar15.pin_spacing","std.ar15.pivot_hole_d","std.ar15.rear_lug_slot_depth","std.ar15.rear_lug_slot_rear_x","std.ar15.rear_lug_slot_width","std.ar15.rear_underside_arc_center_below_seat","std.ar15.rear_underside_arc_center_x","std.ar15.rear_underside_arc_r","std.ar15.rear_underside_round_r","std.ar15.rear_wall_arc_r","std.ar15.receiver_rear_x","std.ar15.safety_detent_boss_below_deck","std.ar15.safety_detent_boss_face","std.ar15.safety_detent_boss_from_rear","std.ar15.safety_detent_boss_length","std.ar15.selector_hole_d","std.ar15.takedown_hole_d","std.ar15.takedown_spotface_d","std.ar15.takedown_spotface_depth","std.ar15.trigger_guard_ear_gap","std.ar15.trigger_guard_ears_width","std.ar15.trigger_guard_front_hole_d","std.ar15.trigger_guard_front_spotface_d","std.ar15.trigger_guard_front_spotface_floor","std.ar15.trigger_guard_rear_hole_d","std.ar15.trigger_pin_x","std.ar15.trigger_slot_front_ahead_of_pin","std.ar15.trigger_slot_length","std.ar15.trigger_slot_width","std.ar15.upper_rear_face_x","std.receiver_extension.milspec_od"]},"profiles":{"side":{"plane":"xy","origin":"the takedown pin centre (the rifle frame origin), +x toward the muzzle","offset":{},"points":[[-1.225,1.175],[-1.19,-0.255],[-1.156,-0.474],[-0.811,-0.516],[-0.575,-0.633],[-0.364,-0.86],[-0.297,-0.995],[-0.288,-1.071],[-0.095,-1.079],[-0.095,-1.348],[-0.069,-1.373],[0.924,-1.945],[1.025,-1.995],[1.16,-1.995],[1.177,-2.314],[1.632,-2.314],[1.674,-2.255],[1.673,-2.171],[1.598,-2.078],[1.454,-1.969],[1.404,-1.885],[1.37,-1.784],[1.37,-1.549],[1.454,-1.33],[1.63,-1.153],[1.681,-1.153],[1.832,-1.085],[2.943,-1.084],[3.01,-1.101],[3.128,-1.151],[3.288,-1.311],[3.356,-1.429],[3.389,-1.546],[3.373,-1.849],[3.323,-1.95],[3.264,-1.976],[3.154,-2.102],[3.154,-2.203],[3.264,-2.329],[3.382,-2.329],[3.432,-2.278],[3.466,-2.312],[3.718,-2.295],[4.762,-2.092],[6.091,-1.872],[6.175,-1.838],[6.217,-1.762],[6.133,-1.628],[6.148,-0.483],[6.199,-0.365],[6.308,-0.256],[6.392,-0.205],[6.476,-0.188],[6.602,-0.062],[6.602,0.073],[6.568,0.14],[6.493,0.199],[6.24,0.215],[6.19,0.249],[6.004,0.249],[5.988,0.265],[5.399,0.248],[3.396,0.263],[3.345,0.246],[2.975,0.262],[2.958,0.245],[2.925,0.262],[2.874,0.245],[2.47,0.245],[2.437,0.262],[2.403,0.245],[2.386,0.262],[0.013,0.259],[-0.071,0.276],[-0.307,0.377],[-0.484,0.604],[-0.568,0.89],[-0.568,1.226],[-0.602,1.546],[-0.678,1.605],[-1.032,1.604],[-1.166,1.571]],"scaleRefs":["std.ar15.pin_spacing"],"inputs":{"std.ar15.pin_spacing":6.375},"tolerance":0.015,"photo":"references/psa-stealth-stripped-lower 92d56fedaacf (left side on white: Palmetto State Armory's gallery picture 7a4a7701.jpg (546 x 546), from the page the user saved 2026-10-12)","method":"luminance < 190, largest piece, holes filled, notches filled in [214, 222, 246, 242] (disk closing, r 40 px); frame from the reviewed holes takedown, pivot (59.4 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.015 in with the extremes kept: 82 points (IoU 0.994 with the full outline); the frame checked at the standard's other holes (selector, trigger, hammer, the guard's rear hole, the catch's hole): each within 0.025 in of the Army drawing's place; checks: −x_min 1.225 ± 0.026; x_max 6.602 ± 0.036; y_max 1.605 ± 0.026; −y_min 2.329 ± 0.027; top (tooth tops: the edge's max over 0.05 in windows) along x [0.6, 5.8] 0.261 ± 0.050 in vs std.ar15.deck_y 0.2485 ± 0.0015 (confirmed): agrees; −x_min in y [-0.4, 0.0] 1.190 ± 0.026 (tools/trace.py)","via":"user","note":"The left side's silhouette, shown facing right, its holes filled; no trigger guard (the ears are the lowest points behind the well). The tower's ring is round, not a prism, and is seen from ahead: its top, its rear and the walls' sweep up to it read as its silhouette does from that lens and are the drawing's in the model."}},"gaps":[{"what":"the right side: no photo of it is on file (the saved page has two pictures, both of the left). The fence, the roll along the well's right wall, the wall's rear edge and everything else on the right are the standard forging's as read on the catalog's other forged mil-spec lowers","need":"a photo of this lower's right side, square on, both pin holes open (the user described three photos of it on a bamboo board, its right side, its left and a view down into it: they are not among the saved files)"},{"what":"its weight: the page states none; the figure used is the model's volume as 7075 (8.47 oz ± 0.85)","need":"a page or a reviewer that weighs the stripped receiver"},{"what":"a sentence that states its trigger and hammer pin size: the page says 'made by a mil-spec contractor' and nothing of the pins; the small pin is taken from the drawing and from the holes' rims on its close-up photo (0.159 and 0.151 in for .157)","need":"a seller's sentence"},{"what":"a larger copy of its left photo: the saved one is 546 px square (0.017 in to the pixel); the page names a full-size original that isn't on file","need":"the full-size picture saved from the user's browser"},{"what":"the depth of the two oblong pockets by the selector on the left, and whether the bolt catch's bosses stop short of the deck (a bright line 0.04 in under it on the photo)","need":"an oblique close-up with a known edge beside them, or a view along the receiver"}]},"psa-stripped-upper":{"id":"psa-stripped-upper","name":"AR-15 Stripped Upper Receiver","manufacturer":"Palmetto State Armory","sku":"51655109407","url":"https://palmettostatearmory.com/psa-ar-15-stripped-upper-receiver.html","category":"upper","description":"Palmetto State Armory's stripped upper: a \"Forged 7075-T6 A3 AR upper\", \"hard coat anodized black for durability\", \"Featuring M4 feedramp cuts and no T marks\". \"Does Not Include Ejection Port Assembly or Forward Assist Assembly.\"","weight":"psa-stripped-upper.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"pins":{"origin":[0,0,0]},"front_face":{"origin":["{.front_face_x}","{.bore_axis_above_pin}",0],"note":"The end of the barrel-nut thread on the bore axis, +x toward the muzzle: a barrel extension's flange seats here, and a handguard is placed from here."},"rear_face":{"origin":["{.receiver_rear_x}","{.bore_axis_above_pin}",0],"note":"The rear face on the bore axis, +x toward the muzzle: the bolt carrier's channel opens here."},"handle_channel":{"origin":["{.handle_seat_x}","{.bore_axis_above_pin} + {.charging_handle_above_bore}",0],"note":"The charging handle's seat on its channel's axis, +x toward the muzzle: the front wall of the open notch under the rail's rear end, which the handle's shoulder stops against, at the notch's mid-height."},"top_rail":{"origin":["{.rail_slot0_x}","{.rail_top_above_pin}",0],"note":"The rail's top at its rearmost slot's centre, +x toward the muzzle (picatinny: index = slot number)."}},"interfaces":{"receiver_pins":{"type":"ar15.upper_lower","role":"upper","anchor":"pins","params":{"pin_spacing":"={std.ar15.pin_spacing}"},"flips":false},"barrel_extension":{"type":"ar15.barrel_extension","role":"receiver","anchor":"front_face","params":{},"flips":false},"handguard_mount":{"type":"ar15.handguard_mount","role":"receiver","anchor":"front_face","params":{"nut":"standard"},"flips":false,"note":"Its page names no handguard or barrel nut: the barrel nut's thread is taken as the Army drawing's (1 1/4-18), which its photo's nose reads as within its ±, on a receiver its page calls a \"Forged 7075-T6 A3 AR upper\"."},"carrier_channel":{"type":"ar15.carrier_channel","role":"receiver","anchor":"rear_face","params":{},"flips":false},"charging_handle_channel":{"type":"ar15.charging_handle_channel","role":"receiver","anchor":"handle_channel","params":{},"flips":false},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}","seam":"={.rail_front_x} - {.rail_slot0_x}","seam_parts":"the receiver's rail and the handguard's","seam_behind":"receiver","seam_ahead":"handguard"},"flips":false,"note":"Its own rail of 13 slots, counted on its page's side photo, unmarked (\"no T marks\"); a handguard's rail ahead of it is the handguard's own."}},"materials":{"receiver":{"label":"Receiver","finish":"anodized","recolorable":true,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized","color":"placeholder-black","sku":"51655109407","source":"https://palmettostatearmory.com/psa-ar-15-stripped-upper-receiver.html"}},"default":"black","note":"Sold in one colour: its page's \"Finish: Black\", \"hard coat anodized black for durability\" (the page as the user saved it, 2026-10-12)."}},"components":{},"geometry":{"components":{"receiver":"psa-stripped-upper.receiver.glb"},"approximations":["Drawn stripped, as it is sold: the forward assist's bore empty and the ejection port without its door (\"Does Not Include Ejection Port Assembly or Forward Assist Assembly\").","Its side outline is its maker's one photo of it, 546 px square (a pixel is 0.016 in), in the frame of its own lug holes, across the mil-spec forging's section: the Army drawing's forged 1.18 round body, the rail's lower faces under its slots' floors the standard's (MIL-STD-1913's), the height of its dovetail's foot, its neck, the flat sides and the walls from the reference CAD set (a third-party model of a mil-spec forging). No end or top view of this receiver is on file, so its own section isn't sourced. That model's step at the neck's foot, a ledge .010 wide where the neck meets the flat side a hundredth further out, isn't drawn (2026-10-12): at the size the page draws a rifle it is a third of a pixel, and it drew as a dashed hairline along the body; the neck's wall leans from its width under the dovetail's foot out to the side's face at the height of the step.","On the right, the forward assist's housing is a cylinder about the Army drawing's axis (20° in plan, placed by the reference model) from where the photo shows its rear face until it has sunk into the round body, solid back to the wall, its .509 bore open; the brass deflector is the photo's outline, rising to the reference model's crest and sloping to the port (the photo has its crease 0.08 further forward than the model's crest: the ledger keeps both); the port is the drawing's (3.125 long; the photo's opening reads 0.06 shorter); the door's two hinge lugs are where the photo shows them, about the reference model's pin axis. How far each stands out is the forging's, not measured on this receiver. What the photo shows nearer its lens than the mid-plane is brought back by its depth, with the lens placed by the two lug holes (about 22 in away).","The left side is the mil-spec forging's whole: the page has no view of it. The cam pin's pad is the reference model's flat face, and the charging handle latch's slot is the Army drawing's (Section D-D: .156 of wall ahead of the notch, .195 long) between the reference model's heights, a pocket down to the drawing's .045 of wall over the channel (cut through into it until 2026-10-20).","The notch under the rail's rear end, where a charging handle's T lies, has its floor and its roof where the photo's see-through has them once its edges are brought back through the lens (0.29 high), and its front wall straight between them, cut to at least the standard's notch (below): the photo's floor stood a hundredth over the block of a handle riding on its lugs.","Behind its rail's head the rail is the standard's tongue (2026-10-20, lib.rail_tongue: the reference model's, ±0.318 with a round end, its rearmost point where this receiver's photo has the rail's end, and two concave rounds out to the head's width by 0.4165 ahead of the pin, where the app's head begins): until then the head was drawn at its full width to the rail's end, square, and every charging handle's T stood in its two corners. The charging handle's channel is the standard's (lib.handle_channel: the Army drawing's tier and roof, 8448524 sheet 2, and the reference model's widths and its two upright rounds), and so is the notch the handle's block lies in at least (lib.handle_notch: the reference model's floor, roof and 45 degree corners); a handle rides on its guide lugs on the tier (std.ar15.charging_handle_axis_y), which this receiver's photo, reading the see-through notch's middle, agrees with within its ±.","The barrel nut's thread is turned as rings at the drawing's pitch and diameters, not a helix; the gas tube's hole, the charging handle's channel and the flange round the rear end are the drawing's and the reference model's, and the lower rear corner is cut to the arc a lower's two rear walls rise along (the Army's .750 R, drawing 8448608 sheet 1: this upper's own drawing has .760, a hundredth clear of them, which isn't drawn). The lugs are the side outline at the drawing's width.","Not drawn: the port door's seat and its detent, the M4 feed ramps the page states, the openings in the underside (it is closed under the bore), the forge mark (the photo has a square one; a buyer's answer on the page says those shipped had another) and the takedown lug's countersink; edges broken at 0.015 in."],"ledger":["psa-stripped-upper.receiver_rear_x","psa-stripped-upper.front_face_x","psa-stripped-upper.underside_y","psa-stripped-upper.rail_top_above_pin","psa-stripped-upper.bore_axis_above_pin"]},"profiles":{"side":{"plane":"xy","origin":"the takedown pin centre (the rifle frame origin), +x toward the muzzle","offset":{},"points":[[-0.621,1.632],[-0.621,0.551],[-0.432,0.408],[-0.282,0.32],[-0.284,-0.141],[-0.269,-0.157],[-0.261,-0.212],[0.231,-0.215],[0.271,-0.176],[0.273,0.063],[0.289,0.078],[0.298,0.245],[0.981,0.241],[0.996,0.257],[3.649,0.243],[3.665,0.258],[6.079,0.245],[6.103,0.221],[6.102,-0.049],[6.133,-0.113],[6.236,-0.185],[6.426,-0.218],[6.554,-0.171],[6.642,-0.068],[6.651,0.242],[6.683,0.258],[6.874,0.256],[6.89,0.272],[6.905,0.256],[6.937,0.256],[6.953,0.272],[6.969,0.256],[7.036,0.306],[7.036,1.434],[7.031,1.455],[6.992,1.479],[6.65,1.473],[6.652,1.791],[6.636,1.806],[6.636,1.886],[6.652,1.902],[6.669,2.013],[6.653,2.029],[6.653,2.076],[6.63,2.1],[6.201,2.103],[6.089,2.04],[6.057,1.992],[6.002,2.016],[6.002,2.08],[5.978,2.104],[5.804,2.105],[5.724,2.042],[5.692,1.994],[5.676,1.994],[5.644,1.995],[5.605,2.035],[5.597,2.106],[5.407,2.107],[5.311,1.996],[5.279,1.997],[5.208,2.021],[5.2,2.108],[5.01,2.109],[4.985,2.054],[5.001,2.038],[4.993,2.03],[4.945,1.999],[4.898,1.999],[4.85,1.999],[4.811,2.023],[4.803,2.11],[4.628,2.111],[4.612,2.016],[4.58,2.001],[4.501,2.001],[4.453,2.001],[4.413,2.025],[4.406,2.113],[4.231,2.114],[4.223,2.026],[4.183,2.003],[4.119,2.003],[4.04,2.004],[4.024,2.019],[4.009,2.115],[3.834,2.116],[3.826,2.029],[3.786,2.005],[3.643,2.006],[3.619,2.03],[3.612,2.117],[3.421,2.118],[3.429,2.031],[3.405,2.007],[3.341,2.007],[3.246,2.008],[3.222,2.032],[3.222,2.08],[3.199,2.119],[3.024,2.12],[3.016,2.017],[2.944,2.01],[2.833,2.01],[2.809,2.034],[2.802,2.122],[2.627,2.123],[2.619,2.035],[2.595,2.012],[2.547,2.012],[2.436,2.012],[2.412,2.036],[2.405,2.124],[2.23,2.125],[2.222,2.053],[2.198,2.014],[2.039,2.015],[1.999,2.055],[2.015,2.07],[2.008,2.126],[1.833,2.127],[1.809,2.103],[1.809,2.04],[1.769,2.016],[1.642,2.017],[1.61,2.033],[1.61,2.128],[1.42,2.129],[1.412,2.058],[1.372,2.018],[1.26,2.019],[1.189,2.043],[1.205,2.059],[1.197,2.13],[-0.534,2.14],[-0.574,2.116],[-0.567,1.934],[-0.487,1.917],[-0.44,1.885],[0.037,1.883],[0.06,1.859],[0.06,1.732],[-0.028,1.629]],"features":{"forward_assist_rim":[[[-0.777,1.292],[-0.586,1.291],[-0.59,0.623],[-0.781,0.624]]],"deflector":[[[2.068,1.641],[2.132,1.736],[2.879,1.732],[2.942,1.573],[2.988,1.382],[2.986,1.001],[2.954,0.874],[2.763,0.859],[2.112,0.863],[2.065,0.942]]],"deflector_crest":[[[2.339,1.703],[2.418,1.703],[2.415,1.131],[2.336,1.131]]],"port":[[[2.988,1.382],[6.133,1.365],[6.131,0.872],[2.986,0.89]]],"hinge_rear":[[[2.826,0.827],[2.953,0.826],[2.952,0.524],[2.825,0.525]]],"hinge_front":[[[6.257,0.808],[6.432,0.807],[6.43,0.505],[6.256,0.506]]]},"scaleRefs":["std.ar15.pin_spacing"],"inputs":{"psa-stripped-upper.front_face_x":7.036,"psa-stripped-upper.receiver_rear_x":-0.621,"std.ar15.pin_spacing":6.375},"tolerance":0.01,"photo":"references/psa-stripped-upper 55761f177232 (Palmetto State Armory's product photo 51655109407.jpg, in the page the user saved on 2026-10-12: the stripped receiver's right side on white, 546 x 546)","method":"luminance < 200, largest piece, holes filled; frame from the reviewed holes takedown, pivot (63.0 px/in, rms 0.000 in over 2 points); origin at the photo's frame; clipped to x min {.receiver_rear_x} = -0.621, x max {.front_face_x} = 7.036; Douglas-Peucker at 0.01 in with the extremes kept: 143 points (IoU 0.998 with the full outline); checks: top (tooth tops: the edge's max over 0.4 in windows) along x [1.0, 6.0] 2.118 ± 0.048; x_min in y [1.45, 1.62] -0.720 ± 0.024; x_min in y [1.95, 2.2] -0.575 ± 0.024; x_max in y [0.6, 1.2] 7.172 ± 0.036; x_max in y [1.6, 2.2] 6.669 ± 0.034; y_min in x [1.0, 5.5] 0.243 ± 0.024; y_max in x [6.75, 6.95] 1.480 ± 0.024; y_min in x [6.75, 6.95] 0.256 ± 0.024; y_max in x [-0.5, -0.1] in y [1.2, 1.75] 1.631 ± 0.025; y_min in x [-0.45, -0.1] in y [1.75, 2.05] 1.884 ± 0.025; features through the same placement (forward_assist_rim: the forward assist housing's rear rim, its bore's dark opening inside it; deflector: the brass deflector's outline: its steep rear face from u 203, the crease at u 221 to 224, its long slope to the port's rear end; deflector_crest: the crease between the deflector's rear face and its slope; port: the ejection port's opening, the dark obround; hinge_rear: the port door's rear hinge lug; hinge_front: the port door's front hinge lug) (tools/trace.py)","via":"user","note":"Its outer silhouette with the lug holes filled, cut at the standard's rear and front faces (the silhouette's own ends are the forward assist's rim and the thread's near rim, nearer the lens); the forward assist's rim, the deflector, the port and the door's hinge lugs as the photo shows them, inside it. A 546 px picture: a pixel is 0.016 in."}},"gaps":[{"what":"Its weight","need":"A page that states one: Palmetto State Armory's gives none, and its site can't be read for another (D59). Not estimated: a build with it says its total weight is unknown"},{"what":"Its left side, its width, and how far its forward assist housing and deflector stand out","need":"A view of the left side, and an end or a top view with a known size in frame: the page has one photo, of the right side, and the mil-spec forging's figures stand in"},{"what":"A larger photo of it","need":"The page's picture at full size, saved by the user (the saved page holds it 546 px square, 63 px to the inch): every reading on it is good to two or three hundredths, and its outline to a pixel"},{"what":"A forward assist and a port door for it","need":"Those parts in the catalog: it is sold without them, and drawn without them"}]},"radian-raptor-charging-handle":{"id":"radian-raptor-charging-handle","name":"Raptor Ambidextrous Charging Handle AR15/M16","manufacturer":"Radian Weapons","sku":"R0001","url":"https://www.primaryarms.com/radian-weapons-ar15-m16-raptor-ambidextrous-charging-handle-black","category":"charging_handle","description":"Radian's Raptor charging handle (\"formerly AXTS Weapons Systems\", Wing Tactical): a latch each side of the T, either one unlatching it, the right-hand one longer \"to clear the forward assist button\" (SpiceTac's review). \"Constructed from 7075 aircraft-grade aluminum\", \"Mil-Spec black anodized finish\", \"Latch Size Medium Latch\" (Primary Arms, SKU and MPN R0001); \"FOR AR15/M16\" is etched on its shaft. The address here is a seller's page for exactly this number; Radian's public product API also verifies R0001 as the black AR15/M16 variant (2026-10-28).","weight":"radian-raptor-charging-handle.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"channel":{"origin":[0,0,0],"note":"The T's shoulder on the channel's axis, +x toward the muzzle (the front face of the ledge under the T's block, 0.68 in wide): it stops against the front wall of the open notch under a receiver's rail's rear end (the receiver's handle_seat_x), and the front hook's tip is `length` ahead (Primary Arms' photo from below reads 5.97 at the shaft's own scale, the Army's drawing has 5.895)."}},"interfaces":{"charging_handle_channel":{"type":"ar15.charging_handle_channel","role":"handle","anchor":"channel","params":{},"flips":false}},"materials":{"body":{"label":"Shaft and plates","finish":"anodized","recolorable":false,"color":"placeholder-black","follows":{"slot":"latches","options":{"np3":{"finish":"nickel","color":"radian-np3"}}},"note":"The shaft, the block the logo is on, the two plates over and under the latches: black on the selectable latch colours except NP3 (Primary Arms' photos of the Flat Dark Earth, Radian OD and red ones; Wing Tactical's six side by side), \"Finish: Mil-Spec Type III Hard Coat Anodized\" (Wing Tactical), \"Mil-Spec black anodized finish\" (Primary Arms). On the NP3 one (R0005) the whole handle is coated: \"This version is finished in a corrosion-resistant NP3 coating\" (Primary Arms)."},"latches":{"label":"Latches","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized_matte","color":"placeholder-black","sku":"R0001","source":"https://www.primaryarms.com/radian-weapons-ar15-m16-raptor-ambidextrous-charging-handle-black"},"tungsten":{"label":"Tungsten Grey","finish":"anodized_matte","color":"radian-tungsten-grey","sku":"R0002","source":"https://www.midwestgunworks.com/page/mgwi/prod/r0001"},"fde":{"label":"Flat Dark Earth","finish":"anodized_matte","color":"radian-fde","sku":"R0003","source":"https://www.primaryarms.com/radian-ar-15-m16-raptor-ambidextrous-charging-handle-flat-dark-earth"},"brown":{"label":"Radian Brown","finish":"anodized_matte","color":"radian-brown","sku":"R0004","source":"https://riflesupply.com/Radian-Raptor-Charging-Handle-AR15-Platform-Brown-R0004_p_262.html"},"np3":{"label":"NP3","finish":"nickel","color":"radian-np3","sku":"R0005","source":"https://www.primaryarms.com/radian-raptor-ambidextrous-ar15-charging-handle-np3"},"red":{"label":"Competition Red","finish":"anodized_matte","color":"radian-red","sku":"R0232","source":"https://www.primaryarms.com/radian-weapons-ar15-m16-raptor-ambidextrous-charging-handle-red"},"blue":{"label":"Competition Blue","finish":"anodized_matte","color":"radian-blue","sku":"R0240","source":"https://ar15discounts.com/products/radian-raptor-competition-ambidextrous-charging-handle-556-red/"},"od":{"label":"Radian OD","finish":"anodized_matte","color":"radian-od","sku":"R0375","source":"https://www.primaryarms.com/radian-raptor-charging-handle-ar15-radian-od"},"grey":{"label":"Radian Grey","finish":"anodized_matte","color":"radian-grey","sku":"R0560","source":"https://alexandersstore.com/product/radian-weapons-raptor-charging-handle-grey/"}},"default":"black","note":"The two latches and the latch's hook arm (one piece with the left latch): what the handle's colour is the colour of (Wing Tactical: \"Available in Black, Radian Brown, Flat Dark Earth, OD Green, Tungsten Grey, and Radian Grey Latches\"). Each number is a seller's page's: R0003 \"finished in Mil-Spec Flat Dark Earth (FDE) anodizing\", R0375 \"finished in Mil-Spec anodized Radian OD Green\", R0232 \"finished in Mil-Spec anodized Red\" (Primary Arms; Alexander's has the same three numbers, and R0560 as Radian Gray, R0005 as NP3); R0004 \"Brown\" (Rifle Supply; AR15Discounts' picture RWR0004 is its brown variant's); R0002 Tungsten, which Midwest Gun Works lists as discontinued; R0240 is the blue by what is left of AR15Discounts' \"Color Blue, Red MPN R0240,R0232\". The red and the blue are Radian's \"Competition\" Raptor, the same handle with COMPETITION on its shaft where the patents' numbers are. Drawn as a blasted anodize (`anodized_matte`): the sellers' word is anodized for every colour, and in every photo the latches are matte and finely grained beside the shaft's satin (Wing Tactical's Tungsten Grey from behind); one seller, Bereli, says of the black one \"Type 3 Mil-Spec Hardcoat Anodized with Black Cerakote\" and \"black Cerakote grip\". Sold and not offered here: Clear Ano (R0140 in the maker's public product API, read 2026-10-28; its exact image URL is known, but that S3 host refuses robots.txt with HTTP 403, leaving the current variant's piece colours unverified; R0656 is only the older 405 px retailer image's filename) and \"Black + NP3\" (SpiceTac's list; no page with a number or a photo is on file)."},"pins":{"label":"Latch pins","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"The two latches' pivot pins, bare steel in the selectable handle colours (\"oversized roll pins\", SpiceTac's review): bright rings in Primary Arms' photos of the red and the Flat Dark Earth ones from above and in Radian's artwork, darker in its photo of the NP3 one; what steel they are isn't stated."},"marking":{"label":"Logo","finish":"steel","recolorable":false,"color":"stainless-natural","follows":{"slot":"latches","options":{"np3":{"finish":"nickel","color":"radian-np3"}}},"note":"Radian's mark, laser-marked pale grey on the black block behind the shaft, the same on the selectable latch colours except NP3 (Primary Arms' and Wing Tactical's photos). The colour is the app's natural-steel grey standing in for bare marked aluminium: no page states one. On the NP3 one the mark is under the coat and reads as a rougher patch of the same grey (Primary Arms' R0005 from above): drawn in the coat's own colour."}},"components":{},"geometry":{"model":"radian-raptor-charging-handle.glb","components":{},"approximations":["Ahead of its shoulder it is cut by what of a forged upper stands beside it (2026-10-20, lib.handle_room): the walls either side of the channel's rear slot, out to the forging's side under the rail (std.ar15.rail_tongue_half_width, ±0.318), the left one less the Army drawing's latch slot, where the hook lies (8448524 Section D-D: .045 of wall left over the channel); and behind it the notch's front wall's two corners, cut back at 45 degrees. Its photos show the latch's arm and the shaft as one outline, where the wall between them is .045 to .109 thick: every handle on file had its arm drawn through it.","Its plan is Primary Arms' photo of the black R0001 from below (the latches with the teeth down their front faces, their windows, the ledge under the block, the latch's hook arm and the gap beside it, the nose, the guide lugs), scaled by the shaft's width; the shaft is put to the Army drawing's length, which the photo reads 1% long (not told apart from it at the photo's scale). The latches' walls are drawn upright from that outline: their upper edges, seen from above, are taken as over their lower ones (the two photos put the latches' tips within 0.006 in of each other).","What shows from above (the upper plate with its two ears and its arc, the opening the latches leave round it, the block the logo is on, the logo, where the rear grooves are) is picked on Primary Arms' photo from above and carried into the plan by the two pins' ends, seen in both; the plate and the opening are their left halves mirrored. The T's rear between the latches is made one flat face (the plan follows the lower plate's corners and the shadowed gaps beside them there).","Two meshes since 2026-10-06, for the colours: the latches (with the hook arm), and the body. Under the opening between the latches the body is the upper plate's column and a lower plate as thick as the ledge (lower_plate_thickness) with the opening's outline; the layer between the two plates there is the latches', where their tongues lie. The shape is the one it was (the same box, 0.7776 cubic inches for 0.7764): the pieces are cut from each other, each with its own edge break, which leaves a fine seam where they meet.","The T's middle is drawn solid from the shaft's underside to the upper plate's top under the plate's outline: on the real handle an upper and a lower plate hold the latches' tongues and their spring between them, with a gap above and below the tongues that shows from behind. The gap round the plate is cut down to the upper plate's underside, as thick as Wing Tactical's photo from behind reads it. The pins' counterbores and the step in the arc's wall aren't drawn.","The block (as thick as the shaft, the logo on it) ends 0.11 in behind the shoulder, where Primary Arms' photo from above has its front face; ahead of it the lower plate runs on to the shoulder as a ledge, at the thickness the design patent's broken lines give it (it is what goes under a receiver's notch's cut-back corners). The slot between the two plates along the T's sides, where the latches' arms lie, isn't cut. The lower faces of the latches are drawn 0.022 in above the shaft's underside (the fitted camera's reading and the patent's), the middle flush with it.","The latch's hook arm is the plan's outline to the left of the shaft, from the block's front face forward, at the two heights the design patent's broken lines give it (no photo is square to the handle's side): it lies on the ledge. Behind the block's front face, where it runs beside the block to the left latch, it isn't drawn apart from the block.","The shaft's thickness, its key channel, its front hook and its guide lugs' height are the Army's drawing's (8448518), which Radian's handle is made to work with (\"FOR AR15/M16\"): the channel, the lugs and the hook are where Primary Arms' photo from below shows them. The channel's rear end is drawn as a ball's; the bore through the hook is on the channel's roof's centre. The top chamfers come in over a straight ramp (the real run-out is a cutter's round) and run to the hook's rear face.","The five grooves down each latch's rear face are round cuts at their counted number, where the top photo has them along the edge, to their depth from a straight line through the teeth's tips; the grooves down the front faces are the plan's own teeth, as the mask caught them. The latches' upper and lower edges are broken at 0.012 in (the real ones are chamfered wider), as every edge is. The pins are drawn as discs at their ends' size; the lettering on the shaft (RADIAN RAPTOR, the two patent numbers, FOR AR15/M16) isn't drawn."],"ledger":["radian-raptor-charging-handle.length","radian-raptor-charging-handle.shaft_width","radian-raptor-charging-handle.shaft_thickness","radian-raptor-charging-handle.latch_height","radian-raptor-charging-handle.latch_lift","radian-raptor-charging-handle.t_height","radian-raptor-charging-handle.upper_plate_thickness","radian-raptor-charging-handle.lower_plate_thickness","radian-raptor-charging-handle.block_front_behind_shoulder","radian-raptor-charging-handle.catch_bottom","radian-raptor-charging-handle.catch_top","radian-raptor-charging-handle.top_flat_width","radian-raptor-charging-handle.top_chamfer_drop","radian-raptor-charging-handle.top_chamfer_from_shoulder","radian-raptor-charging-handle.top_chamfer_full_from_shoulder","radian-raptor-charging-handle.channel_width","radian-raptor-charging-handle.channel_depth","radian-raptor-charging-handle.channel_rear_behind_shoulder","radian-raptor-charging-handle.hook_length","radian-raptor-charging-handle.hook_drop","radian-raptor-charging-handle.hook_fillet_r","radian-raptor-charging-handle.guide_lug_height","radian-raptor-charging-handle.pin_d","radian-raptor-charging-handle.rear_groove_count","radian-raptor-charging-handle.rear_groove_r","radian-raptor-charging-handle.rear_groove_depth"]},"profiles":{"plan":{"plane":"xz","origin":"the T's shoulder (the front face of the ledge under the T's block, at its lower edge: column 422.5 of the photo) on the shaft's centre line, +x toward the muzzle, z to the handle's right","offset":{},"points":[[-1.053,0.419],[-1.049,0.415],[-1.053,0.404],[-1.037,0.381],[-1.033,0.388],[-1.023,0.374],[-1.01,0.369],[-1.026,0.367],[-1.033,0.374],[-1.039,0.372],[-1.042,0.228],[-1.037,0.227],[-1.033,0.234],[-1.026,0.234],[-1.024,0.243],[-1.012,0.255],[-1.006,0.254],[-1.014,0.243],[-1.006,0.239],[-1.024,0.221],[-1.021,0.214],[-1.024,0.203],[-1.017,0.196],[-1.028,0.189],[-1.03,0.223],[-1.042,0.21],[-1.042,0.178],[-1.046,0.174],[-1.042,-0.196],[-1.031,-0.221],[-1.031,-0.232],[-1.042,-0.243],[-1.042,-0.289],[-1.035,-0.329],[-1.039,-0.347],[-1.035,-0.35],[-1.035,-0.386],[-1.015,-0.381],[-1.021,-0.39],[-1.014,-0.397],[-1.028,-0.415],[-1.024,-0.419],[-1.028,-0.437],[-1.024,-0.44],[-1.028,-0.462],[-1.031,-0.462],[-1.031,-0.448],[-1.039,-0.433],[-1.031,-0.426],[-1.039,-0.419],[-1.035,-0.408],[-1.042,-0.412],[-1.042,-0.433],[-1.046,-0.437],[-1.042,-0.44],[-1.042,-0.487],[-1.035,-0.534],[-1.028,-0.555],[-1.017,-0.563],[-1.024,-0.566],[-1.005,-0.597],[-0.98,-0.604],[-0.965,-0.629],[-0.96,-0.623],[-0.96,-0.638],[-0.949,-0.649],[-0.953,-0.656],[-0.949,-0.659],[-0.958,-0.661],[-0.96,-0.652],[-0.956,-0.649],[-0.965,-0.647],[-0.964,-0.663],[-0.947,-0.665],[-0.944,-0.661],[-0.928,-0.677],[-0.921,-0.695],[-0.921,-0.713],[-0.912,-0.711],[-0.906,-0.717],[-0.915,-0.722],[-0.922,-0.719],[-0.924,-0.724],[-0.912,-0.737],[-0.905,-0.736],[-0.901,-0.729],[-0.894,-0.733],[-0.881,-0.749],[-0.874,-0.771],[-0.867,-0.767],[-0.871,-0.792],[-0.874,-0.792],[-0.876,-0.783],[-0.878,-0.796],[-0.851,-0.805],[-0.835,-0.821],[-0.831,-0.846],[-0.835,-0.86],[-0.826,-0.869],[-0.801,-0.876],[-0.792,-0.893],[-0.785,-0.896],[-0.792,-0.928],[-0.774,-0.954],[-0.76,-0.964],[-0.763,-0.972],[-0.742,-1.004],[-0.735,-1],[-0.735,-1.015],[-0.713,-1.047],[-0.706,-1.051],[-0.702,-1.065],[-0.684,-1.086],[-0.684,-1.094],[-0.679,-1.088],[-0.674,-1.09],[-0.677,-1.101],[-0.674,-1.108],[-0.643,-1.142],[-0.604,-1.164],[-0.593,-1.16],[-0.597,-1.167],[-0.518,-1.181],[-0.511,-1.178],[-0.504,-1.185],[-0.371,-1.206],[-0.314,-1.22],[-0.267,-1.213],[-0.228,-1.191],[-0.19,-1.146],[-0.179,-1.117],[-0.179,-1.11],[-0.197,-1.092],[-0.197,-1.07],[-0.183,-1.052],[-0.183,-1.042],[-0.192,-1.033],[-0.195,-1.036],[-0.21,-1.033],[-0.226,-1.013],[-0.222,-0.991],[-0.208,-0.977],[-0.212,-0.959],[-0.238,-0.954],[-0.255,-0.934],[-0.251,-0.912],[-0.237,-0.898],[-0.24,-0.88],[-0.264,-0.878],[-0.283,-0.858],[-0.276,-0.83],[-0.265,-0.822],[-0.265,-0.808],[-0.271,-0.799],[-0.296,-0.795],[-0.308,-0.779],[-0.305,-0.754],[-0.29,-0.743],[-0.29,-0.736],[-0.299,-0.72],[-0.321,-0.72],[-0.337,-0.704],[-0.337,-0.682],[-0.319,-0.66],[-0.326,-0.643],[-0.314,-0.637],[-0.312,-0.632],[-0.317,-0.63],[-0.335,-0.641],[-0.35,-0.641],[-0.366,-0.625],[-0.362,-0.596],[-0.337,-0.578],[-0.337,-0.527],[-0.33,-0.491],[-0.312,-0.448],[-0.301,-0.434],[-0.29,-0.401],[-0.285,-0.396],[-0.281,-0.407],[-0.242,-0.374],[-0.217,-0.367],[-0.17,-0.366],[-0.149,-0.374],[-0.124,-0.373],[-0.048,-0.388],[-0.023,-0.387],[0.027,-0.398],[0.099,-0.405],[0.102,-0.409],[0.145,-0.408],[0.149,-0.412],[0.346,-0.397],[0.363,-0.384],[0.363,-0.348],[0.352,-0.319],[0.23,-0.208],[0.235,-0.199],[0.612,-0.197],[0.623,-0.194],[0.627,-0.197],[0.907,-0.196],[0.911,-0.199],[0.947,-0.196],[0.95,-0.199],[1.231,-0.198],[1.238,-0.194],[1.242,-0.198],[1.57,-0.196],[1.573,-0.2],[1.588,-0.196],[1.649,-0.196],[1.653,-0.2],[1.682,-0.196],[1.685,-0.2],[1.757,-0.199],[1.761,-0.196],[1.768,-0.199],[1.779,-0.195],[1.783,-0.199],[2.169,-0.197],[2.176,-0.194],[2.18,-0.197],[2.201,-0.197],[2.22,-0.193],[2.241,-0.197],[2.248,-0.19],[2.252,-0.197],[2.306,-0.197],[2.306,-0.193],[2.295,-0.193],[2.295,-0.19],[2.328,-0.189],[2.332,-0.197],[2.346,-0.197],[2.355,-0.184],[2.346,-0.171],[2.36,-0.175],[2.364,-0.167],[2.404,-0.164],[2.407,-0.167],[2.433,-0.167],[2.44,-0.164],[2.444,-0.167],[2.494,-0.167],[2.5,-0.172],[2.458,-0.174],[2.462,-0.182],[2.476,-0.181],[2.478,-0.187],[2.454,-0.185],[2.463,-0.194],[2.458,-0.2],[3.07,-0.197],[3.081,-0.2],[3.088,-0.197],[3.091,-0.2],[3.095,-0.197],[3.117,-0.197],[3.12,-0.2],[3.153,-0.2],[3.168,-0.196],[3.171,-0.2],[3.236,-0.2],[3.244,-0.196],[3.247,-0.2],[3.305,-0.199],[3.309,-0.196],[3.327,-0.199],[3.325,-0.19],[3.331,-0.188],[3.338,-0.199],[3.367,-0.199],[3.371,-0.195],[3.374,-0.199],[4.493,-0.198],[4.497,-0.201],[4.562,-0.204],[4.595,-0.215],[4.65,-0.244],[4.806,-0.243],[4.81,-0.236],[4.817,-0.243],[4.828,-0.243],[4.89,-0.214],[4.952,-0.199],[5.484,-0.197],[5.488,-0.2],[5.565,-0.2],[5.565,-0.196],[5.55,-0.196],[5.55,-0.193],[5.579,-0.193],[5.583,-0.2],[5.594,-0.203],[5.623,-0.203],[5.634,-0.196],[5.674,-0.199],[5.673,-0.205],[5.678,-0.214],[5.824,-0.217],[5.828,-0.213],[5.842,-0.217],[5.883,-0.202],[5.914,-0.167],[5.936,-0.135],[5.961,-0.069],[5.969,0.004],[5.965,0.007],[5.961,0.051],[5.943,0.102],[5.925,0.131],[5.919,0.129],[5.892,0.156],[5.895,0.167],[5.864,0.187],[5.842,0.187],[5.839,0.19],[5.693,0.19],[5.678,0.175],[5.667,0.175],[5.634,0.186],[5.638,0.193],[5.521,0.196],[5.517,0.2],[5.448,0.199],[5.444,0.188],[5.435,0.194],[5.437,0.199],[4.992,0.197],[4.988,0.2],[4.941,0.2],[4.937,0.204],[4.923,0.204],[4.919,0.196],[4.879,0.211],[4.879,0.214],[4.888,0.216],[4.879,0.222],[4.868,0.225],[4.864,0.218],[4.859,0.223],[4.861,0.229],[4.835,0.243],[4.646,0.242],[4.58,0.209],[4.522,0.198],[3.595,0.197],[3.592,0.2],[3.588,0.197],[3.574,0.2],[3.556,0.197],[3.552,0.2],[3.53,0.2],[3.527,0.196],[3.516,0.2],[3.497,0.196],[3.494,0.2],[3.487,0.196],[3.472,0.2],[2.802,0.196],[2.798,0.2],[2.791,0.196],[2.776,0.2],[2.769,0.196],[2.747,0.2],[2.744,0.196],[2.74,0.2],[2.686,0.199],[2.679,0.196],[2.675,0.199],[2.176,0.197],[2.173,0.2],[2.165,0.2],[2.162,0.193],[2.133,0.2],[2.126,0.196],[2.097,0.2],[2.089,0.193],[2.082,0.2],[2.068,0.196],[2.064,0.2],[1.483,0.197],[1.48,0.189],[1.473,0.197],[1.469,0.193],[1.465,0.197],[1.447,0.193],[1.444,0.2],[1.411,0.193],[1.375,0.2],[1.361,0.196],[1.354,0.2],[0.666,0.196],[0.663,0.2],[0.609,0.196],[0.605,0.199],[0.005,0.2],[0,0.205],[0,0.328],[-0.027,0.351],[-0.045,0.343],[-0.056,0.347],[-0.203,0.346],[-0.206,0.35],[-0.224,0.346],[-0.242,0.35],[-0.237,0.355],[-0.24,0.366],[-0.289,0.414],[-0.292,0.403],[-0.316,0.441],[-0.341,0.506],[-0.348,0.542],[-0.348,0.581],[-0.36,0.587],[-0.373,0.603],[-0.369,0.631],[-0.35,0.644],[-0.335,0.644],[-0.33,0.657],[-0.33,0.664],[-0.341,0.671],[-0.348,0.686],[-0.341,0.711],[-0.321,0.724],[-0.31,0.724],[-0.305,0.733],[-0.305,0.743],[-0.319,0.758],[-0.323,0.776],[-0.307,0.799],[-0.285,0.803],[-0.276,0.819],[-0.294,0.841],[-0.294,0.859],[-0.278,0.879],[-0.256,0.882],[-0.251,0.895],[-0.269,0.924],[-0.265,0.942],[-0.249,0.958],[-0.226,0.964],[-0.226,0.982],[-0.24,0.999],[-0.24,1.021],[-0.221,1.041],[-0.206,1.041],[-0.197,1.054],[-0.197,1.061],[-0.212,1.079],[-0.208,1.108],[-0.188,1.12],[-0.178,1.12],[-0.172,1.129],[-0.172,1.14],[-0.186,1.158],[-0.186,1.176],[-0.17,1.196],[-0.151,1.202],[-0.154,1.241],[-0.165,1.274],[-0.19,1.309],[-0.228,1.336],[-0.278,1.35],[-0.324,1.346],[-0.378,1.331],[-0.536,1.302],[-0.568,1.287],[-0.599,1.26],[-0.602,1.253],[-0.593,1.24],[-0.582,1.251],[-0.57,1.253],[-0.591,1.227],[-0.609,1.195],[-0.616,1.191],[-0.627,1.166],[-0.656,1.13],[-0.659,1.115],[-0.695,1.068],[-0.695,1.061],[-0.717,1.032],[-0.72,1.018],[-0.795,0.906],[-0.803,0.884],[-0.813,0.877],[-0.853,0.805],[-0.867,0.798],[-0.863,0.794],[-0.878,0.772],[-0.878,0.765],[-0.899,0.74],[-0.938,0.675],[-0.942,0.66],[-0.96,0.646],[-0.971,0.617],[-1.003,0.574],[-1.003,0.567],[-1.021,0.538],[-1.021,0.527],[-1.028,0.52],[-1.035,0.484],[-1.031,0.477],[-1.035,0.473],[-1.039,0.412],[-1.046,0.415],[-1.042,0.419],[-1.042,0.455],[-1.046,0.458],[-1.042,0.462],[-1.046,0.469],[-1.039,0.473],[-1.046,0.48],[-1.039,0.48],[-1.039,0.487],[-1.046,0.491],[-1.046,0.505],[-1.049,0.505]],"features":{"windows":[[[-0.777,0.733],[-0.774,0.773],[-0.756,0.809],[-0.538,1.156],[-0.504,1.19],[-0.482,1.201],[-0.432,1.209],[-0.378,1.223],[-0.339,1.224],[-0.314,1.213],[-0.29,1.186],[-0.287,1.136],[-0.402,0.797],[-0.402,0.786],[-0.423,0.728],[-0.441,0.699],[-0.464,0.679],[-0.493,0.669],[-0.522,0.668],[-0.565,0.679],[-0.615,0.679],[-0.686,0.664],[-0.726,0.667],[-0.747,0.678],[-0.763,0.694]],[[-0.763,-0.763],[-0.763,-0.727],[-0.756,-0.709],[-0.74,-0.689],[-0.693,-0.667],[-0.672,-0.667],[-0.611,-0.681],[-0.547,-0.681],[-0.525,-0.674],[-0.475,-0.674],[-0.446,-0.684],[-0.427,-0.701],[-0.405,-0.74],[-0.402,-0.762],[-0.394,-0.772],[-0.312,-1.01],[-0.312,-1.042],[-0.319,-1.06],[-0.332,-1.076],[-0.364,-1.094],[-0.403,-1.095],[-0.529,-1.07],[-0.575,-1.052],[-0.599,-1.029],[-0.631,-0.975],[-0.727,-0.835],[-0.727,-0.828],[-0.738,-0.817],[-0.756,-0.784]]],"catch_gap":[[[0,-0.263],[0,-0.205],[0.016,-0.2],[0.181,-0.199],[0.187,-0.241],[0.194,-0.259],[0.187,-0.284],[0.17,-0.297],[0.113,-0.3],[0.109,-0.304],[0.034,-0.294],[0.005,-0.283],[0.011,-0.277],[0.011,-0.259],[0.005,-0.258]]],"pins":[[[-0.595,0.433],[-0.584,0.433],[-0.584,0.423],[-0.595,0.423]],[[-0.588,-0.422],[-0.578,-0.422],[-0.578,-0.433],[-0.588,-0.433]]],"plate":[[[-1.072,0.198],[-1.046,0.222],[-1.03,0.238],[-1.002,0.25],[-0.951,0.264],[-0.898,0.278],[-0.844,0.293],[-0.798,0.307],[-0.765,0.326],[-0.742,0.354],[-0.724,0.391],[-0.71,0.438],[-0.697,0.485],[-0.678,0.522],[-0.651,0.546],[-0.614,0.557],[-0.567,0.558],[-0.525,0.544],[-0.49,0.519],[-0.464,0.482],[-0.45,0.44],[-0.447,0.398],[-0.456,0.361],[-0.475,0.333],[-0.503,0.323],[-0.542,0.309],[-0.583,0.288],[-0.628,0.253],[-0.667,0.206],[-0.697,0.154],[-0.719,0.084],[-0.726,-0.001],[-0.718,-0.085],[-0.694,-0.155],[-0.664,-0.206],[-0.624,-0.252],[-0.579,-0.287],[-0.537,-0.308],[-0.498,-0.321],[-0.47,-0.33],[-0.451,-0.358],[-0.441,-0.395],[-0.443,-0.437],[-0.457,-0.479],[-0.482,-0.516],[-0.517,-0.542],[-0.559,-0.557],[-0.605,-0.557],[-0.643,-0.546],[-0.67,-0.523],[-0.689,-0.485],[-0.704,-0.439],[-0.718,-0.393],[-0.737,-0.356],[-0.76,-0.328],[-0.793,-0.309],[-0.84,-0.296],[-0.893,-0.282],[-0.947,-0.269],[-0.998,-0.255],[-1.026,-0.244],[-1.043,-0.228],[-1.068,-0.205]]],"opening":[[[-1.092,0.402],[-1.015,0.399],[-0.945,0.39],[-0.882,0.388],[-0.829,0.395],[-0.789,0.414],[-0.762,0.447],[-0.743,0.491],[-0.725,0.538],[-0.697,0.573],[-0.66,0.597],[-0.609,0.604],[-0.558,0.602],[-0.512,0.589],[-0.469,0.563],[-0.434,0.524],[-0.41,0.478],[-0.399,0.424],[-0.403,0.378],[-0.421,0.343],[-0.449,0.319],[-0.444,-0.316],[-0.416,-0.339],[-0.397,-0.374],[-0.392,-0.42],[-0.403,-0.474],[-0.426,-0.521],[-0.461,-0.561],[-0.503,-0.586],[-0.549,-0.601],[-0.6,-0.603],[-0.652,-0.597],[-0.689,-0.574],[-0.717,-0.539],[-0.736,-0.493],[-0.755,-0.449],[-0.783,-0.416],[-0.823,-0.398],[-0.876,-0.391],[-0.939,-0.394],[-1.009,-0.404],[-1.085,-0.409]]],"block":[[[-0.475,0.333],[-0.503,0.323],[-0.542,0.309],[-0.583,0.288],[-0.628,0.253],[-0.667,0.206],[-0.697,0.154],[-0.719,0.084],[-0.726,-0.001],[-0.718,-0.085],[-0.694,-0.155],[-0.664,-0.206],[-0.624,-0.252],[-0.579,-0.287],[-0.537,-0.308],[-0.498,-0.321],[-0.47,-0.33],[-0.439,-0.356],[-0.23,-0.37],[0.282,-0.366],[0.277,0.35],[-0.445,0.345]]],"logo":[[[-0.442,0.085],[-0.37,0.061],[-0.258,0.118],[-0.257,-0.001],[-0.193,-0.055],[-0.195,0.232]],[[-0.58,0.002],[-0.354,-0.06],[-0.191,-0.224],[-0.192,-0.14],[-0.328,0],[-0.51,0.043]]],"rear_grooves":[[[-0.982,0.632],[-0.972,0.632],[-0.972,0.621],[-0.982,0.621]],[[-0.936,0.702],[-0.926,0.702],[-0.926,0.691],[-0.936,0.691]],[[-0.89,0.772],[-0.879,0.772],[-0.879,0.761],[-0.89,0.761]],[[-0.847,0.843],[-0.836,0.843],[-0.836,0.832],[-0.847,0.832]],[[-0.805,0.915],[-0.795,0.915],[-0.795,0.904],[-0.805,0.904]],[[-0.973,-0.629],[-0.962,-0.629],[-0.962,-0.64],[-0.973,-0.64]],[[-0.926,-0.693],[-0.915,-0.693],[-0.915,-0.704],[-0.926,-0.704]],[[-0.879,-0.765],[-0.868,-0.765],[-0.868,-0.776],[-0.879,-0.776]],[[-0.832,-0.835],[-0.821,-0.835],[-0.821,-0.846],[-0.832,-0.846]],[[-0.789,-0.904],[-0.779,-0.904],[-0.779,-0.915],[-0.789,-0.915]]]},"scaleRefs":["radian-raptor-charging-handle.shaft_width"],"inputs":{"radian-raptor-charging-handle.shaft_width":0.4},"tolerance":0.003,"photo":"references/radian-raptor-charging-handle 10e25db90367 (Primary Arms: the black R0001 from below, on white, 2200 x 1467)","method":"luminance < 82, largest piece, holes filled; scale from radian-raptor-charging-handle.shaft_width = 0.4 in, the tube's own width column by column: 110.8 px over columns 560–900, 110.6 px over columns 1000–1600, 109.8 px over columns 1820–1950; a line through them (rms 0.17 px) changes -0.8% from column 560 to 1950, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 276.6 px/in there. The axis is the tube's centre line (tilt +0.28°, rms 0.06 px); origin at column 422.5 of the photo, on the tube's axis; Douglas-Peucker at 0.003 in with the extremes kept: 519 points (IoU 0.995 with the full outline); Seen from below, the muzzle to the right: the handle's right side is up in the photo. Taken from about 27 in over the handle's middle: the latches' front faces and the windows' walls show as grey bands (115 to 145 of 255), left out of the mask, so the outline is the lower faces' edges.; checks: x_max 5.969 ± 0.083 in vs radian-raptor-charging-handle.length 5.895 ± 0.01 (confirmed): agrees; height in x [4.66, 4.86] 0.487 ± 0.013 in vs radian-raptor-charging-handle.guide_lug_width 0.488 ± 0.005 (confirmed): agrees; features through the same placement (windows: the opening through each latch, at its lower face; catch_gap: the gap between the latch's hook arm and the shaft's left side, closed at its front by the hook's tooth; pins: the two pivot pins' lower ends, each a 3 px square about the bright end's centre (258.0, 636.2 and 259.8, 874.0); plate: the upper plate (the cover over the latches' pivots, D705,384's claim): its neck between the latches, its two ears round the pins and the arc at its front, concave to the muzzle; its left half picked and mirrored about the middle between the pins; drawn past the T's rear face, which is its edge there; picked at 4x to 8x on Primary Arms' photo from above (f83c3853e399) and carried into this photo by the two pins' ends, seen in both (429.9 px/in there; it puts the latches' tips 1.346 and 1.214 off the centre line where this photo has 1.350 and 1.220, and the shoulder 0.02 ahead); opening: what the two latches leave open between them at their upper faces: their inner edges beside the plate's neck and round its ears (the plate stands in it with a gap all round); its left half picked and mirrored; picked at 4x to 8x on Primary Arms' photo from above (f83c3853e399) and carried into this photo by the two pins' ends, seen in both (429.9 px/in there; it puts the latches' tips 1.346 and 1.214 off the centre line where this photo has 1.350 and 1.220, and the shoulder 0.02 ahead); block: the block ahead of the plate's arc, as thick as the shaft, where the logo is: from the arc forward past the shoulder, between its two sides; picked at 4x to 8x on Primary Arms' photo from above (f83c3853e399) and carried into this photo by the two pins' ends, seen in both (429.9 px/in there; it puts the latches' tips 1.346 and 1.214 off the centre line where this photo has 1.350 and 1.220, and the shoulder 0.02 ahead); logo: Radian's mark, laser-marked on the block: its two pieces; picked at 4x to 8x on Primary Arms' photo from above (f83c3853e399) and carried into this photo by the two pins' ends, seen in both (429.9 px/in there; it puts the latches' tips 1.346 and 1.214 off the centre line where this photo has 1.350 and 1.220, and the shoulder 0.02 ahead); rear_grooves: the five round grooves down each latch's rear face, each a 3 px square about its deepest point as the top photo has it (the right latch's five from the inside out, then the left's); picked at 4x to 8x on Primary Arms' photo from above (f83c3853e399) and carried into this photo by the two pins' ends, seen in both (429.9 px/in there; it puts the latches' tips 1.346 and 1.214 off the centre line where this photo has 1.350 and 1.220, and the shoulder 0.02 ahead)) (tools/trace.py)","via":"harvest","note":"From below: the shaft with its nose and guide lugs, the ledge under the T's block (the shoulder), the latch's hook on the left, the two latches with their teeth, the T's rear."}},"gaps":[{"what":"Radian's own figures","need":"The maker's public product API verifies current colour identities and image URLs (2026-10-28), including Clear Ano R0140. The weight remains a seller's and a reviewer's, and no length, width or height on file is a maker's figure."},{"what":"A straight side view","need":"A photo square to the handle's side (none is on file): the latch's hook arm's two heights, the step from the block down to the ledge behind the shoulder, the plates' thicknesses. The heights drawn are through a camera fitted to one oblique photo and from the design patent's two side views, which agree."},{"what":"Its seat checked on a photo of it in a receiver","need":"A pin-framed photo of the handle latched in an upper: it is placed with its shoulder (the ledge's front face) against the front wall of the receiver's notch, as the Army's handle stops. Wing Tactical says it \"May NOT fit on some SIG ARs, specifically the 516 Model\": no SIG receiver is in the catalog, and nothing checks it."},{"what":"Two colours' numbers on one page each, and two colours not offered","need":"A second page for the blue's number (R0240 is what is left of AR15Discounts' pair of numbers once the red is R0232) and for Tungsten Grey's (R0002 on Midwest Gun Works' list alone, where it is discontinued); for Black + NP3, a page with the number and a photo large enough to read its colour map. Clear Ano's identity is resolved as R0140 by the maker's public API (2026-10-28), but its image host refuses robots.txt with HTTP 403, so its piece colours remain unverified and it is not selectable. The older R0656 retailer-image filename is not the adopted identifier; that 405 px image cannot resolve the current variant's appearance."},{"what":"The lower plate's own outline, and the latches' tongues","need":"A photo square to the handle's underside with the latches in a colour (Wing Tactical's is oblique): under the opening the lower plate is drawn with the opening's outline, and what lies between the two plates there is all the latches' colour, where the real tongues leave a gap at the middle."}]},"radian-raptor-lt-charging-handle":{"id":"radian-raptor-lt-charging-handle","name":"AR-15 / M16 Raptor-LT Ambidextrous Charging Handle","manufacturer":"Radian Weapons","sku":"R0148","url":"https://www.primaryarms.com/radian-raptor-lt-ambidextrous-ar15-charging-handle-black","category":"charging_handle","description":"Radian's Raptor-LT: the Raptor with its two handles over-moulded in polymer. \"Utilizing the same patented ambidextrous functionality as the Radian Raptor, the Raptor-LT handles are machined from 7075 aluminum, MILSPEC Type III hard anodized, then over-molded with high-strength, fiberglass reinforced polymer\" (Midwest Gun Works, whose words for it the name is); \"Same as the Standard but features aluminum latches over-molded with high-strength reinforced polymer.\" (T.REX ARMS). \"FOR AR15/M16\" is etched on its shaft, with two design patents' numbers (USD694354, USD705384; a later one in Primary Arms' photo of the grey has US10337811 and USD738452). Fit, as a seller says it: \"*May NOT fit on some SIG AR's, specifically the 516 Model\" (Wing Tactical; no SIG receiver is in the catalog, and nothing checks it). Radian's own page isn't read (it is drawn by script): the address here is a seller's page for exactly this number (\"SKU: R0148 MPN: R0148\", Primary Arms).","weight":"radian-raptor-lt-charging-handle.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"channel":{"origin":[0,0,0],"note":"The T's shoulder on the channel's axis, +x toward the muzzle (the front face of the ledge under the T's block): it stops against the front wall of the open notch under a receiver's rail's rear end (the receiver's handle_seat_x), and the front hook's tip is `length` ahead (Primary Arms' photo from below reads 5.97 at the shaft's own scale, the Army's drawing has 5.895)."}},"interfaces":{"charging_handle_channel":{"type":"ar15.charging_handle_channel","role":"handle","anchor":"channel","params":{},"flips":false}},"materials":{"body":{"label":"Shaft, plates and handle cores","finish":"anodized","recolorable":false,"color":"placeholder-black","note":"Everything of aluminium: the shaft, the block the logo is on, the two plates over and under the handles' pivots, and what shows of the handles' cores (the latch's hook arm beside the shaft, the two tongues between the plates at the T's rear). Black on every colour of handle (Primary Arms' photos of the black, the Flat Dark Earth and the grey one from above and from below; Wing Tactical's three side by side): \"This version pairs a Mil-Spec black anodized body with\" black, Flat Dark Earth or Gray \"reinforced polymer latches\" (Primary Arms), \"Body: Mil-Spec Type III Hard Coat Anodized\" (Wing Tactical); the cores too (\"7075-T6 ALUMINUM CORE WITH MIL-SPEC TYPE III ANODIZED FINISH\", SpiceTac's picture of them bare)."},"latches":{"label":"Handles","finish":"polymer","recolorable":false,"color":"placeholder-polymer-black","sheen":"matte","options":{"black":{"label":"Black","finish":"polymer","color":"placeholder-polymer-black","sheen":"matte","sku":"R0148","source":"https://www.primaryarms.com/radian-raptor-lt-ambidextrous-ar15-charging-handle-black"},"fde":{"label":"Flat Dark Earth","finish":"polymer","color":"radian-lt-fde","sheen":"matte","sku":"R0149","source":"https://www.primaryarms.com/radian-raptor-lt-ambidextrous-ar-15-charging-handle"},"grey":{"label":"Grey","finish":"polymer","color":"radian-lt-grey","sheen":"matte","sku":"R0150","source":"https://www.primaryarms.com/radian-raptor-lt-ambidextrous-ar15-charging-handle-gray"}},"default":"black","note":"The polymer moulded over the two handles: what the handle's colour is the colour of. \"Latch: Over-Molded Polymer (Black, Flat Dark Earth, and Grey)\", \"Colors are designed to match standard Magpul® color offerings\" (Wing Tactical). Each number is a seller's page's: \"SKU: R0148 MPN: R0148\" black, \"SKU: R0149 MPN: R0149\" Flat Dark Earth, R0150 Grey (Primary Arms, a page each); \"SKU COLOR R0148 Black R0149 FDE R0150 Stealth Grey\" (Midwest Gun Works); Right To Bear calls the grey Tungsten Grey. Matte and finely grained in every photo, the panel sunk in each face smoother. Sold in no other colour by the pages on file."},"pins":{"label":"Pivot pins","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"The two handles' pivot pins, bare steel on every colour (bright rings in Primary Arms' photos of all three from above and from below); what steel they are isn't stated."},"marking":{"label":"Logo","finish":"steel","recolorable":false,"color":"stainless-natural","note":"Radian's mark, laser-marked pale grey on the black block behind the shaft, the same on every colour of handle (Primary Arms' and Wing Tactical's photos). The colour is the app's natural-steel grey standing in for bare marked aluminium: no page states one."}},"components":{},"geometry":{"model":"radian-raptor-lt-charging-handle.glb","components":{},"approximations":["Ahead of its shoulder it is cut by what of a forged upper stands beside it (2026-10-20, lib.handle_room): the walls either side of the channel's rear slot, out to the forging's side under the rail (std.ar15.rail_tongue_half_width, ±0.318), the left one less the Army drawing's latch slot, where the hook lies (8448524 Section D-D: .045 of wall left over the channel); and behind it the notch's front wall's two corners, cut back at 45 degrees. Its photos show the latch's arm and the shaft as one outline, where the wall between them is .045 to .109 thick: every handle on file had its arm drawn through it.","Its plan is Primary Arms' photo of the black R0148 from below (the handles with the teeth down their front faces, the ledge under the block, the latch's hook arm and the gap beside it, the nose, the guide lugs), scaled by the shaft's width; the shaft is put to the Army drawing's length, which the photo reads 1% long (not told apart from it at the photo's scale). The handles' walls are drawn upright from that outline, the lower faces' edges. Primary Arms' photo from above, carried by the pins, has the upper faces' rear edges about 0.02 in further back (the ribs' crests 0.036 to 0.038 behind the plan's face, the ribs standing 0.015 off theirs), the T's rear between the handles 0.025 further, and the tips within 0.01: either the lower rear edges are broken that wide or the two photos don't quite register; the model takes the plan, and the T is that much shallower than the photo from above has it (t_depth holds both readings).","What shows from above is carried into the plan by the two pins' ends, seen in both photos: the opening the polymer leaves round the plates, the panel sunk in each upper face, the logo and where the rear ribs and the front grooves are, each picked on Primary Arms' photo of this handle from above; the upper plate (its neck, its two ears, its arc) and the block the logo is on are the Raptor's own outlines, which drawn over this handle's photo lie on its plate and block all round (the opening is its left half mirrored).","Two meshes for the colours: the polymer of the two handles, and everything of aluminium. The polymer is drawn as the whole of each handle outside the opening round the plates, solid (the aluminium core inside each isn't drawn apart: a flat plate with openings, by Wing Tactical's x-ray banner). Under the opening the T's middle is one black solid from the shaft's underside to the upper plate's underside: on the real handle a lower plate, the two handles' tongues and their springs, with a gap over and under the tongues that shows from behind. The pins' counterbores aren't drawn.","The handles' heights are read through a camera fitted to one oblique photo (their front face unwrapped: ± 0.03 on the height, ± 0.015 on where the lower face is): they come out 0.015 in above the upper plate's top, and their lower faces 0.045 above the shaft's underside. The T's own heights (the plates, the block, the ledge, the hook arm) are the Raptor's, by reference in the ledger: no photo of this handle is square to its side.","Each rear face has its five ribs as rounds standing off a flat face, at their counted number, where the photo from above has their crests along the edge, running the face's whole height (on the real one they end under the upper edge's break, and Radian's mark is moulded into the right handle's face beyond them: not drawn). The grooves down the front faces are cut at their counted number (seven on the right handle, six on the left), where the photo from above has each along the edge, as slots with round floors at the width and depth that photo's edge shows, in a face made smooth through the crests of the plan's own teeth (the plan, traced from below, catches the same grooves as ragged teeth; its crests lie up to 0.013 in off the smooth face). Their depth is the upper edge's, which is broken: down the face they may be deeper. Primary Arms' oblique photo shows a finer line between each two, which isn't drawn; the rib beyond the outermost groove and the tip's corner are the plan's own, squarer than the real ones. The edges are broken at 0.012 in; the real handles' are rounder.","The panel in each upper face is sunk to one depth with upright walls (the real walls lean a little and the floor has a moulding mark); the shallow panel in each lower face, and the round mark in it, aren't drawn: no view on file shows how deep it is.","The shaft's thickness, its key channel, its front hook and its guide lugs' height are the Army's drawing's (8448518), through the Raptor's ledger: the channel, the lugs and the hook are where Primary Arms' photo from below shows them. The channel's rear end is drawn as a ball's; the top chamfers come in over a straight ramp. The lettering on the shaft (RADIAN RAPTOR-LT, the patents' numbers, FOR AR15/M16) isn't drawn."],"ledger":["radian-raptor-lt-charging-handle.length","radian-raptor-lt-charging-handle.shaft_width","radian-raptor-lt-charging-handle.shaft_thickness","radian-raptor-lt-charging-handle.latch_height","radian-raptor-lt-charging-handle.latch_lift","radian-raptor-lt-charging-handle.t_height","radian-raptor-lt-charging-handle.upper_plate_thickness","radian-raptor-lt-charging-handle.lower_plate_thickness","radian-raptor-lt-charging-handle.block_front_behind_shoulder","radian-raptor-lt-charging-handle.catch_bottom","radian-raptor-lt-charging-handle.catch_top","radian-raptor-lt-charging-handle.top_flat_width","radian-raptor-lt-charging-handle.top_chamfer_drop","radian-raptor-lt-charging-handle.top_chamfer_from_shoulder","radian-raptor-lt-charging-handle.top_chamfer_full_from_shoulder","radian-raptor-lt-charging-handle.channel_width","radian-raptor-lt-charging-handle.channel_depth","radian-raptor-lt-charging-handle.channel_rear_behind_shoulder","radian-raptor-lt-charging-handle.hook_length","radian-raptor-lt-charging-handle.hook_drop","radian-raptor-lt-charging-handle.hook_fillet_r","radian-raptor-lt-charging-handle.guide_lug_height","radian-raptor-lt-charging-handle.pin_d","radian-raptor-lt-charging-handle.rear_rib_count","radian-raptor-lt-charging-handle.rear_rib_r","radian-raptor-lt-charging-handle.rear_rib_height","radian-raptor-lt-charging-handle.panel_depth","radian-raptor-lt-charging-handle.front_groove_count","radian-raptor-lt-charging-handle.front_groove_count_left","radian-raptor-lt-charging-handle.front_groove_width","radian-raptor-lt-charging-handle.front_groove_depth"]},"profiles":{"plan":{"plane":"xz","origin":"the T's shoulder (the front face of the ledge under the T's block, at its lower edge: the dark runs to column 421 of the photo beside the shaft) on the shaft's centre line, +x toward the muzzle, z to the handle's right","offset":{},"points":[[-1.059,0.462],[-1.055,0.433],[-1.059,0.419],[-1.048,0.39],[-1.034,0.375],[-1.045,0.321],[-1.045,0.202],[-1.048,0.199],[-1.048,-0.187],[-1.037,-0.227],[-1.048,-0.241],[-1.048,-0.292],[-1.045,-0.295],[-1.045,-0.331],[-1.03,-0.364],[-1.03,-0.386],[-1.045,-0.396],[-1.052,-0.411],[-1.055,-0.447],[-1.052,-0.451],[-1.045,-0.53],[-1.034,-0.566],[-1.01,-0.604],[-0.985,-0.607],[-0.973,-0.616],[-0.958,-0.642],[-0.962,-0.674],[-0.953,-0.683],[-0.931,-0.683],[-0.911,-0.707],[-0.904,-0.721],[-0.904,-0.732],[-0.911,-0.743],[-0.908,-0.753],[-0.895,-0.763],[-0.884,-0.759],[-0.877,-0.763],[-0.865,-0.775],[-0.85,-0.8],[-0.857,-0.815],[-0.854,-0.833],[-0.848,-0.838],[-0.823,-0.842],[-0.807,-0.862],[-0.8,-0.876],[-0.803,-0.909],[-0.791,-0.918],[-0.773,-0.918],[-0.753,-0.941],[-0.746,-0.956],[-0.753,-0.974],[-0.749,-0.992],[-0.706,-1.049],[-0.677,-1.1],[-0.636,-1.149],[-0.614,-1.163],[-0.567,-1.177],[-0.549,-1.177],[-0.459,-1.199],[-0.304,-1.224],[-0.272,-1.217],[-0.243,-1.203],[-0.218,-1.181],[-0.186,-1.163],[-0.151,-1.129],[-0.137,-1.1],[-0.133,-1.082],[-0.133,-1.053],[-0.139,-1.044],[-0.153,-1.044],[-0.157,-1.051],[-0.164,-1.051],[-0.173,-1.06],[-0.166,-1.064],[-0.173,-1.071],[-0.175,-1.087],[-0.177,-1.071],[-0.184,-1.064],[-0.177,-1.053],[-0.186,-1.051],[-0.196,-1.062],[-0.204,-1.062],[-0.223,-1.028],[-0.207,-1.012],[-0.193,-1.008],[-0.187,-1.013],[-0.184,-0.999],[-0.166,-0.977],[-0.166,-0.963],[-0.182,-0.957],[-0.189,-0.972],[-0.193,-0.968],[-0.2,-0.975],[-0.211,-0.972],[-0.214,-0.979],[-0.223,-0.974],[-0.222,-0.965],[-0.229,-0.972],[-0.243,-0.975],[-0.259,-0.945],[-0.259,-0.934],[-0.25,-0.925],[-0.229,-0.921],[-0.222,-0.914],[-0.22,-0.927],[-0.213,-0.927],[-0.216,-0.905],[-0.205,-0.894],[-0.205,-0.876],[-0.218,-0.871],[-0.25,-0.892],[-0.259,-0.887],[-0.258,-0.882],[-0.279,-0.885],[-0.288,-0.876],[-0.288,-0.865],[-0.295,-0.858],[-0.295,-0.844],[-0.29,-0.838],[-0.265,-0.831],[-0.238,-0.804],[-0.238,-0.79],[-0.25,-0.781],[-0.254,-0.788],[-0.272,-0.795],[-0.279,-0.795],[-0.286,-0.788],[-0.308,-0.795],[-0.317,-0.79],[-0.317,-0.779],[-0.324,-0.768],[-0.324,-0.75],[-0.312,-0.741],[-0.297,-0.741],[-0.288,-0.732],[-0.292,-0.725],[-0.286,-0.719],[-0.279,-0.723],[-0.272,-0.719],[-0.263,-0.707],[-0.267,-0.699],[-0.276,-0.694],[-0.283,-0.708],[-0.294,-0.701],[-0.308,-0.716],[-0.31,-0.703],[-0.304,-0.694],[-0.322,-0.701],[-0.337,-0.701],[-0.346,-0.685],[-0.35,-0.663],[-0.346,-0.656],[-0.321,-0.642],[-0.328,-0.613],[-0.322,-0.607],[-0.31,-0.609],[-0.317,-0.624],[-0.317,-0.638],[-0.308,-0.64],[-0.304,-0.647],[-0.303,-0.638],[-0.31,-0.634],[-0.306,-0.624],[-0.31,-0.616],[-0.304,-0.615],[-0.297,-0.625],[-0.285,-0.62],[-0.29,-0.6],[-0.297,-0.604],[-0.322,-0.6],[-0.351,-0.607],[-0.357,-0.602],[-0.36,-0.584],[-0.357,-0.562],[-0.348,-0.553],[-0.33,-0.546],[-0.319,-0.528],[-0.313,-0.53],[-0.312,-0.539],[-0.301,-0.524],[-0.294,-0.528],[-0.288,-0.523],[-0.281,-0.494],[-0.281,-0.472],[-0.267,-0.432],[-0.276,-0.423],[-0.285,-0.44],[-0.281,-0.443],[-0.297,-0.449],[-0.295,-0.461],[-0.304,-0.467],[-0.31,-0.461],[-0.31,-0.447],[-0.303,-0.44],[-0.299,-0.425],[-0.281,-0.414],[-0.295,-0.407],[-0.268,-0.391],[-0.258,-0.391],[-0.25,-0.384],[-0.236,-0.38],[-0.178,-0.38],[-0.135,-0.387],[-0.099,-0.387],[-0.063,-0.394],[0.11,-0.409],[0.114,-0.412],[0.186,-0.412],[0.189,-0.409],[0.236,-0.409],[0.24,-0.405],[0.351,-0.398],[0.368,-0.382],[0.357,-0.328],[0.222,-0.199],[0.243,-0.199],[0.247,-0.196],[0.258,-0.199],[0.323,-0.196],[0.326,-0.199],[0.38,-0.199],[0.388,-0.196],[0.391,-0.199],[0.402,-0.196],[0.409,-0.199],[0.424,-0.196],[0.427,-0.199],[0.431,-0.196],[1.051,-0.196],[1.058,-0.199],[1.066,-0.196],[1.069,-0.199],[4.529,-0.198],[4.595,-0.213],[4.663,-0.245],[4.794,-0.245],[4.805,-0.242],[4.819,-0.245],[4.823,-0.242],[4.848,-0.242],[4.903,-0.213],[4.964,-0.198],[5.53,-0.198],[5.533,-0.194],[5.577,-0.194],[5.581,-0.198],[5.649,-0.198],[5.664,-0.194],[5.678,-0.202],[5.711,-0.202],[5.715,-0.205],[5.849,-0.205],[5.882,-0.191],[5.912,-0.16],[5.942,-0.116],[5.967,-0.044],[5.971,0.018],[5.963,0.061],[5.938,0.123],[5.92,0.152],[5.885,0.186],[5.863,0.197],[5.686,0.197],[5.675,0.186],[5.66,0.186],[5.62,0.2],[5.617,0.197],[5.602,0.2],[5.595,0.197],[5.588,0.2],[4.953,0.2],[4.892,0.214],[4.841,0.243],[4.649,0.243],[4.591,0.214],[4.533,0.2],[0.452,0.198],[0.449,0.201],[0.005,0.201],[0,0.206],[0,0.326],[0.011,0.326],[0.007,0.34],[-0.009,0.349],[-0.218,0.349],[-0.236,0.352],[-0.238,0.362],[-0.254,0.378],[-0.272,0.389],[-0.283,0.403],[-0.295,0.405],[-0.303,0.43],[-0.313,0.437],[-0.321,0.459],[-0.328,0.466],[-0.331,0.499],[-0.339,0.509],[-0.339,0.578],[-0.364,0.603],[-0.36,0.636],[-0.351,0.645],[-0.33,0.641],[-0.321,0.647],[-0.328,0.654],[-0.328,0.679],[-0.346,0.69],[-0.342,0.726],[-0.333,0.739],[-0.312,0.742],[-0.306,0.748],[-0.31,0.751],[-0.303,0.758],[-0.301,0.771],[-0.288,0.769],[-0.29,0.775],[-0.312,0.775],[-0.321,0.784],[-0.324,0.794],[-0.317,0.816],[-0.308,0.832],[-0.297,0.836],[-0.286,0.836],[-0.279,0.829],[-0.281,0.841],[-0.274,0.849],[-0.277,0.859],[-0.263,0.863],[-0.283,0.868],[-0.295,0.877],[-0.285,0.917],[-0.276,0.923],[-0.254,0.919],[-0.256,0.924],[-0.245,0.939],[-0.245,0.95],[-0.24,0.955],[-0.231,0.953],[-0.236,0.962],[-0.243,0.959],[-0.263,0.971],[-0.252,1.007],[-0.218,1.016],[-0.211,1.031],[-0.209,1.022],[-0.196,1.009],[-0.182,1.013],[-0.173,1.022],[-0.178,1.035],[-0.182,1.031],[-0.207,1.053],[-0.222,1.053],[-0.231,1.062],[-0.231,1.069],[-0.211,1.103],[-0.196,1.099],[-0.177,1.112],[-0.18,1.127],[-0.177,1.13],[-0.189,1.136],[-0.195,1.148],[-0.187,1.177],[-0.171,1.19],[-0.157,1.175],[-0.144,1.181],[-0.155,1.188],[-0.155,1.195],[-0.151,1.206],[-0.144,1.21],[-0.144,1.217],[-0.151,1.238],[-0.159,1.242],[-0.159,1.257],[-0.173,1.285],[-0.211,1.323],[-0.276,1.348],[-0.348,1.341],[-0.409,1.323],[-0.434,1.323],[-0.467,1.312],[-0.485,1.312],[-0.546,1.298],[-0.578,1.283],[-0.605,1.256],[-0.771,0.992],[-0.774,0.971],[-0.767,0.956],[-0.774,0.938],[-0.794,0.915],[-0.816,0.915],[-0.825,0.906],[-0.818,0.873],[-0.829,0.859],[-0.832,0.845],[-0.845,0.835],[-0.863,0.835],[-0.872,0.83],[-0.875,0.816],[-0.868,0.794],[-0.892,0.756],[-0.913,0.756],[-0.926,0.743],[-0.919,0.715],[-0.937,0.682],[-0.946,0.677],[-0.964,0.677],[-0.976,0.664],[-0.969,0.646],[-0.969,0.632],[-0.983,0.606],[-0.996,0.597],[-1.018,0.597],[-1.03,0.581],[-1.052,0.52],[-1.055,0.466]],"features":{"catch_gap":[[[0,-0.259],[0,-0.205],[0.005,-0.2],[0.023,-0.196],[0.11,-0.196],[0.114,-0.2],[0.124,-0.196],[0.182,-0.196],[0.18,-0.216],[0.191,-0.255],[0.184,-0.284],[0.175,-0.293],[0.157,-0.301],[0.114,-0.301],[0.11,-0.304],[0.074,-0.301],[0.013,-0.286],[0.014,-0.255],[0.005,-0.261]]],"pins":[[[-0.61,0.44],[-0.599,0.44],[-0.599,0.429],[-0.61,0.429]],[[-0.601,-0.419],[-0.59,-0.419],[-0.59,-0.43],[-0.601,-0.43]]],"plate":[[[-1.086,0.203],[-1.06,0.227],[-1.044,0.243],[-1.016,0.255],[-0.965,0.269],[-0.912,0.283],[-0.858,0.298],[-0.812,0.312],[-0.779,0.331],[-0.756,0.359],[-0.738,0.396],[-0.724,0.443],[-0.711,0.49],[-0.692,0.527],[-0.665,0.551],[-0.628,0.562],[-0.581,0.563],[-0.539,0.549],[-0.504,0.524],[-0.478,0.487],[-0.464,0.445],[-0.461,0.403],[-0.47,0.366],[-0.489,0.338],[-0.517,0.328],[-0.556,0.314],[-0.597,0.293],[-0.642,0.258],[-0.681,0.211],[-0.711,0.159],[-0.733,0.089],[-0.74,0.004],[-0.732,-0.08],[-0.708,-0.15],[-0.678,-0.201],[-0.638,-0.247],[-0.593,-0.282],[-0.551,-0.303],[-0.512,-0.316],[-0.484,-0.325],[-0.465,-0.353],[-0.455,-0.39],[-0.457,-0.432],[-0.471,-0.474],[-0.496,-0.511],[-0.531,-0.537],[-0.573,-0.552],[-0.619,-0.552],[-0.657,-0.541],[-0.684,-0.518],[-0.703,-0.48],[-0.718,-0.434],[-0.732,-0.388],[-0.751,-0.351],[-0.774,-0.323],[-0.807,-0.304],[-0.854,-0.291],[-0.907,-0.277],[-0.961,-0.264],[-1.012,-0.25],[-1.04,-0.239],[-1.057,-0.223],[-1.082,-0.2]]],"opening":[[[-1.084,0.002],[-1.086,0.378],[-1.038,0.38],[-0.99,0.381],[-0.942,0.383],[-0.894,0.391],[-0.87,0.4],[-0.846,0.413],[-0.822,0.427],[-0.798,0.451],[-0.781,0.476],[-0.769,0.5],[-0.76,0.524],[-0.75,0.543],[-0.738,0.563],[-0.722,0.577],[-0.702,0.584],[-0.678,0.589],[-0.642,0.592],[-0.606,0.59],[-0.57,0.583],[-0.534,0.573],[-0.51,0.562],[-0.486,0.545],[-0.467,0.526],[-0.449,0.502],[-0.435,0.478],[-0.423,0.454],[-0.413,0.43],[-0.406,0.406],[-0.391,0.382],[-0.367,0.363],[-0.341,0.353],[-0.336,-0.34],[-0.362,-0.349],[-0.386,-0.369],[-0.401,-0.393],[-0.408,-0.417],[-0.417,-0.441],[-0.429,-0.465],[-0.444,-0.489],[-0.46,-0.514],[-0.479,-0.533],[-0.503,-0.55],[-0.527,-0.562],[-0.563,-0.572],[-0.599,-0.579],[-0.635,-0.582],[-0.671,-0.58],[-0.695,-0.575],[-0.715,-0.568],[-0.732,-0.554],[-0.744,-0.535],[-0.753,-0.515],[-0.763,-0.491],[-0.775,-0.467],[-0.793,-0.444],[-0.817,-0.419],[-0.841,-0.405],[-0.865,-0.393],[-0.889,-0.384],[-0.937,-0.377],[-0.985,-0.375],[-1.033,-0.375],[-1.081,-0.373],[-1.084,0.002]]],"block":[[[-0.489,0.338],[-0.517,0.328],[-0.556,0.314],[-0.597,0.293],[-0.642,0.258],[-0.681,0.211],[-0.711,0.159],[-0.733,0.089],[-0.74,0.004],[-0.732,-0.08],[-0.708,-0.15],[-0.678,-0.201],[-0.638,-0.247],[-0.593,-0.282],[-0.551,-0.303],[-0.512,-0.316],[-0.484,-0.325],[-0.453,-0.351],[-0.244,-0.365],[0.268,-0.361],[0.263,0.355],[-0.459,0.35]]],"logo":[[[-0.471,0.073],[-0.387,0.05],[-0.286,0.111],[-0.285,-0.002],[-0.22,-0.067],[-0.222,0.222]],[[-0.615,-0.004],[-0.545,0.037],[-0.367,-0.005],[-0.338,-0.027],[-0.219,-0.141],[-0.219,-0.237],[-0.386,-0.07]]],"panels":[[[-0.787,0.673],[-0.679,0.673],[-0.583,0.679],[-0.523,0.675],[-0.499,0.689],[-0.48,0.718],[-0.451,0.79],[-0.416,0.887],[-0.375,0.983],[-0.34,1.08],[-0.316,1.152],[-0.321,1.195],[-0.351,1.219],[-0.406,1.226],[-0.478,1.216],[-0.533,1.186],[-0.605,1.126],[-0.674,1.005],[-0.752,0.885],[-0.824,0.764],[-0.843,0.72],[-0.833,0.687]],[[-0.821,-0.703],[-0.802,-0.775],[-0.76,-0.847],[-0.711,-0.919],[-0.663,-0.991],[-0.62,-1.05],[-0.584,-1.092],[-0.548,-1.11],[-0.476,-1.115],[-0.404,-1.115],[-0.35,-1.103],[-0.331,-1.079],[-0.344,-1.036],[-0.374,-0.965],[-0.407,-0.893],[-0.441,-0.821],[-0.472,-0.749],[-0.488,-0.701],[-0.508,-0.683],[-0.574,-0.689],[-0.647,-0.687],[-0.707,-0.678],[-0.761,-0.669],[-0.803,-0.676]]],"front_grooves":[[[-0.324,0.607],[-0.313,0.607],[-0.313,0.596],[-0.324,0.596]],[[-0.299,0.697],[-0.289,0.697],[-0.289,0.687],[-0.299,0.687]],[[-0.276,0.788],[-0.265,0.788],[-0.265,0.777],[-0.276,0.777]],[[-0.251,0.881],[-0.24,0.881],[-0.24,0.87],[-0.251,0.87]],[[-0.226,0.974],[-0.215,0.974],[-0.215,0.963],[-0.226,0.963]],[[-0.203,1.062],[-0.192,1.062],[-0.192,1.052],[-0.203,1.051]],[[-0.179,1.153],[-0.168,1.153],[-0.168,1.142],[-0.179,1.142]],[[-0.324,-0.563],[-0.313,-0.563],[-0.313,-0.573],[-0.324,-0.573]],[[-0.3,-0.656],[-0.289,-0.656],[-0.289,-0.667],[-0.3,-0.667]],[[-0.276,-0.752],[-0.265,-0.752],[-0.265,-0.763],[-0.276,-0.763]],[[-0.253,-0.842],[-0.242,-0.842],[-0.242,-0.853],[-0.253,-0.853]],[[-0.23,-0.933],[-0.219,-0.933],[-0.219,-0.944],[-0.23,-0.944]],[[-0.208,-1.022],[-0.197,-1.022],[-0.197,-1.033],[-0.208,-1.033]]],"rear_ribs":[[[-1.006,0.665],[-0.996,0.665],[-0.996,0.654],[-1.006,0.654]],[[-0.957,0.754],[-0.946,0.754],[-0.946,0.743],[-0.957,0.743]],[[-0.904,0.834],[-0.893,0.834],[-0.893,0.823],[-0.904,0.823]],[[-0.859,0.911],[-0.848,0.911],[-0.848,0.9],[-0.859,0.9]],[[-0.807,0.991],[-0.796,0.991],[-0.796,0.98],[-0.807,0.98]],[[-0.991,-0.667],[-0.98,-0.667],[-0.98,-0.678],[-0.991,-0.678]],[[-0.938,-0.748],[-0.927,-0.748],[-0.927,-0.759],[-0.938,-0.759]],[[-0.882,-0.827],[-0.871,-0.827],[-0.871,-0.838],[-0.882,-0.838]],[[-0.826,-0.907],[-0.815,-0.907],[-0.815,-0.918],[-0.826,-0.918]],[[-0.773,-0.983],[-0.762,-0.983],[-0.762,-0.994],[-0.773,-0.994]]]},"scaleRefs":["radian-raptor-lt-charging-handle.shaft_width"],"inputs":{"radian-raptor-lt-charging-handle.shaft_width":0.4},"tolerance":0.003,"photo":"references/radian-raptor-lt-charging-handle 9a677043deaa (Primary Arms: the black R0148 from below, on white, 2200 x 1467)","method":"luminance < 82, largest piece, holes filled; scale from radian-raptor-lt-charging-handle.shaft_width = 0.4 in, the tube's own width column by column: 110.6 px over columns 560–900, 110.8 px over columns 1000–1600, 110.0 px over columns 1830–1960; a line through them (rms 0.27 px) changes -0.3% from column 560 to 1960, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 276.7 px/in there. The axis is the tube's centre line (tilt +0.02°, rms 0.15 px); origin at column 421.5 of the photo, on the tube's axis; Douglas-Peucker at 0.003 in with the extremes kept: 414 points (IoU 0.996 with the full outline); Seen from below, the muzzle to the right: the handle's right side is up in the photo. The same set-up as Primary Arms' photo of the Raptor from below (the shaft 111 px wide in both). The handles' front faces show as grey bands (left out of the mask), so the outline is the lower faces' edges.; checks: x_max 5.971 ± 0.084 in vs radian-raptor-lt-charging-handle.length 5.895 ± 0.01 (confirmed): agrees; height in x [4.66, 4.86] 0.489 ± 0.013 in vs radian-raptor-lt-charging-handle.guide_lug_width 0.488 ± 0.005 (confirmed): agrees; features through the same placement (catch_gap: the gap between the latch's hook arm and the shaft's left side, closed at its front by the hook's tooth; pins: the two pivot pins' lower ends, each a 3 px square about the bright end's centre; plate: the upper plate (the cover over the handles' pivots, D705,384's claim): its neck between the handles, its two ears round the pins and the arc at its front, concave to the muzzle. It is the Raptor's plate (radian-raptor-charging-handle's plan, picked on that handle's own photo from above), carried by the two pins: drawn over this handle's photo from above (R0148_03, 5d168cd4d6e1) it lies on the plate's edge all round, within 2 px of 416 to the inch (scratch/xfer_L.png); drawn past the T's rear face, which is its edge there; opening: what the two polymer handles leave open between them: their inner edges beside the plate's neck and round its ears (the plate stands in it, with the handles' black cores showing in the gap); its left half picked and mirrored; picked on gridded enlargements of Primary Arms' photo from above (R0148_03, 5d168cd4d6e1) and carried into this photo by the two pins' ends, seen in both (415.9 px/in there; it puts the handles' tips 1.356 and 1.231 off the centre line where this photo has 1.347 and 1.226); block: the block ahead of the plate's arc, as thick as the shaft, where the logo is: from the arc forward past the shoulder, between its two sides. The Raptor's, carried by the two pins as the plate is: its arc and its sides lie on this handle's in its photo from above; logo: Radian's mark, laser-marked on the block: its two pieces; picked on gridded enlargements of Primary Arms' photo from above (R0148_03, 5d168cd4d6e1) and carried into this photo by the two pins' ends, seen in both (415.9 px/in there; it puts the handles' tips 1.356 and 1.231 off the centre line where this photo has 1.347 and 1.226); panels: the panel sunk in each handle's upper face, at its rim (the right handle's, then the left's); picked on gridded enlargements of Primary Arms' photo from above (R0148_03, 5d168cd4d6e1) and carried into this photo by the two pins' ends, seen in both (415.9 px/in there; it puts the handles' tips 1.356 and 1.231 off the centre line where this photo has 1.347 and 1.226); front_grooves: the grooves down each handle's front face, each a 3 px square at its place along the edge as the top photo's own edge profile has it (scratch/teeth.py, teeth2.py: a line walked beside the edge, the edge's dips; the squares lie on that line, 10 to 25 px ahead of the edge: only where along the face each groove is, is taken from them). Seven on the right handle from the root out, then six on the left; picked on gridded enlargements of Primary Arms' photo from above (R0148_03, 5d168cd4d6e1) and carried into this photo by the two pins' ends, seen in both (415.9 px/in there; it puts the handles' tips 1.356 and 1.231 off the centre line where this photo has 1.347 and 1.226); rear_ribs: the five ribs down each handle's rear face, each a 3 px square about its crest as the top photo's outline has it (the right handle's from the inside out, then the left's); picked on gridded enlargements of Primary Arms' photo from above (R0148_03, 5d168cd4d6e1) and carried into this photo by the two pins' ends, seen in both (415.9 px/in there; it puts the handles' tips 1.356 and 1.231 off the centre line where this photo has 1.347 and 1.226)) (tools/trace.py)","via":"harvest","note":"From below: the shaft with its nose and guide lugs, the ledge under the T's block (the shoulder), the latch's hook on the left, the two polymer handles with their teeth and ribs, the T's rear."}},"gaps":[{"what":"Radian's own page","need":"Its figures and its numbers by colour: the maker's pages are drawn by script and returned only a heading (left alone, D59). A page saved from the user's own browser would give them; until then the weight is one reviewer's weighing, and no length, width or height is a maker's."},{"what":"A straight side view, and one square to the T's rear","need":"A photo square to the handle's side or rear (none is on file): the handles' height and where their two faces lie against the plates', read here through a camera fitted to one oblique photo; the panels' depth; the break along the handles' lower rear edges."},{"what":"A second weighing","need":"The one weight on file is a reviewer's kitchen scale, to a tenth of an ounce; a seller repeats it. The model can't check it closer than that: no density for the handles' polymer is on file (its aluminium alone comes to 0.96 oz, and all of it as aluminium to 1.48)."},{"what":"Its seat checked on a photo of it in a receiver","need":"A pin-framed photo of the handle latched in an upper: it is placed with its shoulder (the ledge's front face) against the front wall of the receiver's notch, as the Army's handle stops. Wing Tactical says it \"*May NOT fit on some SIG AR's, specifically the 516 Model\": no SIG receiver is in the catalog, and nothing checks it. A buyer's review at Primary Arms says it wouldn't seat in his Palmetto State Armory pistol upper until he stoned its side lugs (one report; no rule is made of it)."},{"what":"The later marking, and Wing Tactical's and Silencer Shop's prices","need":"Primary Arms' photo of the grey one has US10337811 and USD738452 on its shaft where the black and the Flat Dark Earth ones have USD694354 and USD705384: which handles carry which isn't said by a page. Wing Tactical's page sells the three colours under one offer at the black one's price and a range beside it, and Silencer Shop's markup has no offer: neither is listed."}]},"radian-raptor-sd-charging-handle":{"id":"radian-raptor-sd-charging-handle","name":"Raptor-SD Ambidextrous Charging Handle AR15/M16","manufacturer":"Radian Weapons","sku":"R0006","url":"https://radianweapons.com/product/raptor-sd","category":"charging_handle","description":"Radian's Raptor with a ported shaft: \"The suppressor-optimized Raptor-SD™ features a ported shaft designed to redirect gasses down and forward, away from the shooter’s face when shooting suppressed.\" \"Machined from 7075-T6 aluminum\", \"MILSPEC Type 3 Hard Coat Anodized Finish w/ Cerakote Color Options\", sizes AR15/M16 and AR10/SR25 (Radian's page; this is the AR15/M16 one). \"The square shaft profile fills gaps in the receiver, forcing excess gas back through the ports and away from the shooter.\" (T.REX ARMS). Six notches along each of the shaft's top corners, each with a hole through it into the key's channel (US 10,203,174, which Radian's patents page lists for the RAPTOR-SD; \"US9995543\" and \"USD694354\" are etched on its shaft with \"FOR AR15/M16\"). The black one is R0006 (Primary Arms' \"SKU: R0006 MPN: R0006\"; Midwest Gun Works' table). Fit, as sellers say it: \"will work in the same builds that accept the original Raptor Ambidextrous Charging Handle\", \"*May NOT fit on some SIG ARs, specifically the 516 Model\" (Wing Tactical; no SIG receiver is in the catalog, and nothing checks it).","weight":"radian-raptor-sd-charging-handle.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"channel":{"origin":[0,0,0],"note":"The T's shoulder on the channel's axis, +x toward the muzzle (the front face of the ledge under the T's block): it stops against the front wall of the open notch under a receiver's rail's rear end (the receiver's handle_seat_x), and the front hook's tip is `length` ahead (Primary Arms' photo from below reads 5.968 at the shaft's own scale, the Army's drawing has 5.895)."}},"interfaces":{"charging_handle_channel":{"type":"ar15.charging_handle_channel","role":"handle","anchor":"channel","params":{},"flips":false}},"materials":{"body":{"label":"Shaft, block and plates","finish":"anodized","recolorable":false,"color":"placeholder-black","note":"The shaft with its ports, the block, the plates and the ledge: black on every colour of latch (Primary Arms' R0066, R0376 and R0561 photos, Midwest Gun Works' four side by side, Wing Tactical's lineup): \"This version is finished in Mil-Spec black anodizing\" (Primary Arms, R0006), \"MILSPEC Type 3 Hard Coat Anodized Finish\" (Radian)."},"latches":{"label":"Latches","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black Anodized","finish":"anodized_matte","color":"placeholder-black","sku":"R0006","source":"https://www.midwestgunworks.com/page/mgwi/prod/raptor-sd-ar15"},"fde":{"label":"Flat Dark Earth","finish":"anodized_matte","color":"radian-sd-fde","sku":"R0066","source":"https://www.midwestgunworks.com/page/mgwi/prod/raptor-sd-ar15"},"od":{"label":"Radian OD","finish":"anodized_matte","color":"radian-od","sku":"R0376","source":"https://www.midwestgunworks.com/page/mgwi/prod/raptor-sd-ar15"},"grey":{"label":"Radian Grey","finish":"anodized_matte","color":"radian-grey","sku":"R0561","source":"https://www.midwestgunworks.com/page/mgwi/prod/raptor-sd-ar15"},"tungsten":{"label":"Tungsten Grey","finish":"anodized_matte","color":"radian-tungsten-grey","sku":"R0065","source":"https://www.kygunco.com/product/radian-weapons-r0065-raptor-sd-ambi-charging-handle-ar15-m16-grey"}},"default":"black","note":"The two latches and the latch's hook arm (one piece with the left latch): what the handle's colour is the colour of. Radian's page offers \"Black Anodized Flat Dark Earth Radian OD Radian Grey\"; Midwest Gun Works pairs each with its number (\"SKU COLOR R0006 Black R0066 FDE R0376 Radian OD R0561 Radian Grey\"); KYGunCo has R0065 as \"TUNGSTEN GREY\", an older colour Radian no longer lists (AR15Discounts' picture of it, 681620e3899b). The black, Radian OD, Radian Grey and Tungsten Grey are Radian's own presets, fitted on the Raptor's latches in the same colours (data/colors/radian.yaml): one maker's colour by one name, and on this handle's own photos the Radian OD and Radian Grey read where the Raptor's targets do (Primary Arms R0376_01's latch flats #636054 and #5c584e for the Raptor's #605d4b; R0561_01's #575757 for #5a5a59). The Flat Dark Earth doesn't: Primary Arms R0066_01, the SD's T from above, reads its latch flats #765e47 and #745b3f where R0003, the Raptor's in the same series and pose, reads #957e66, with the logo (#b3b4ac, #bab9b5) and the black block (#2d2a29, #373634) within 10 levels: this handle's FDE is about 30 levels darker, and has its own preset fitted to that photo (radian-sd-fde). Finish words differ: Primary Arms \"finished in Mil-Spec FDE anodizing\", \"Mil-Spec anodized Radian OD Green\"; Radian \"Hard Coat Anodized Finish w/ Cerakote Color Options\"; Alexander's \"OD Green Cerakote over MIL-SPEC Type III Hard Coat Anodize\": drawn as the Raptor's are, a blasted anodize (matte, finely grained in every photo). Sold and not offered here: Radian Brown, NP3 and \"NP3 / Black Latch\" (Wing Tactical's list; no page pairs a number with any of them: R0067, R0068 and R0255 are in Wing's list unpaired)."},"pins":{"label":"Latch pins","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"The two latches' pivot pins' ends, bright in every colour (Primary Arms' photos of the black from below and of the FDE from above); what steel they are isn't stated."}},"components":{},"geometry":{"model":"radian-raptor-sd-charging-handle.glb","components":{},"approximations":["Ahead of its shoulder it is cut by what of a forged upper stands beside it (2026-10-20, lib.handle_room): the walls either side of the channel's rear slot, out to the forging's side under the rail (std.ar15.rail_tongue_half_width, ±0.318), the left one less the Army drawing's latch slot, where the hook lies (8448524 Section D-D: .045 of wall left over the channel); and behind it the notch's front wall's two corners, cut back at 45 degrees. Its photos show the latch's arm and the shaft as one outline, where the wall between them is .045 to .109 thick: every handle on file had its arm drawn through it.","Its plan is Primary Arms' photo of the black R0006 from below (the latches with the teeth down their faces, their windows, the ledge, the latch's hook arm and the gap beside it, the shaft with its guide lugs and nose), scaled by the shaft's width; the shaft is put to the Army drawing's length, which the photo reads 1.2% long. The latches' walls are drawn upright from that outline (the lower faces' edges).","The T's middle between the latches is the block (the logo's, as wide as the plan is beside the shoulder) at the shaft's thickness, and on it the upper plate at the T's height: behind its arc and round each pin as an ear (plate_arc_behind_pins, plate_arc_r: Primary Arms' photo of the FDE one's T from above; plate_ear_r: the render from above). The arc is drawn as a circle through its middle; the plate's straight sides and its rear are the block's, and the opening the latches leave round the plate isn't cut (the plate stands against the latches): its outline isn't traced for this handle. The logo isn't drawn.","The T's height is Impact Guns' render of the right side's (level from the latch's tip to its root, flush underneath with the shaft); the latch's hook arm's two heights and the ledge's are the design patent's broken lines (US D694,354, which Radian marks the SD with): no view of this handle is square to its left side.","The shaft is square, the Army drawing's .400 by .2985 with no top chamfers (\"the square shaft profile fills gaps in the receiver\", T.REX ARMS; the render from above has its top flat to the edges); its key channel, its front hook and its guide lugs are the drawing's, the channel's rear end drawn as a ball's.","Each port is a notch in one top corner whose face lies on the corner's diagonal (a 45-degree face: it reaches 0.116 down the side in the side render and 0.116 in across the top in the render from above), its two end walls leaning forward as the side render's parallelogram has them, and a round hole square to that face through into the channel (US 10,203,174 FIG. 9C). Where each pair is along the shaft is where the photo from below sees its holes through the channel; the notch is placed round its hole by the side render's offsets, scaled by the ports' own pitch (that render's along and across scales differ by 3%). The notches' and holes' edges are broken at the model's 0.012 in, sharper than the real ones' rounds.","The rear grooves and the teeth down the latches' faces are the plan's own outline, as the mask caught them; the latches' upper edges aren't chamfered beyond the 0.012 in break. The lettering on the shaft isn't drawn."],"ledger":["radian-raptor-sd-charging-handle.length","radian-raptor-sd-charging-handle.shaft_width","radian-raptor-sd-charging-handle.shaft_thickness","radian-raptor-sd-charging-handle.t_height","radian-raptor-sd-charging-handle.latch_lift","radian-raptor-sd-charging-handle.block_front_behind_shoulder","radian-raptor-sd-charging-handle.lower_plate_thickness","radian-raptor-sd-charging-handle.catch_bottom","radian-raptor-sd-charging-handle.catch_top","radian-raptor-sd-charging-handle.channel_width","radian-raptor-sd-charging-handle.channel_depth","radian-raptor-sd-charging-handle.channel_rear_behind_shoulder","radian-raptor-sd-charging-handle.hook_length","radian-raptor-sd-charging-handle.hook_drop","radian-raptor-sd-charging-handle.hook_fillet_r","radian-raptor-sd-charging-handle.guide_lug_height","radian-raptor-sd-charging-handle.pin_d","radian-raptor-sd-charging-handle.plate_arc_behind_pins","radian-raptor-sd-charging-handle.plate_ear_r","radian-raptor-sd-charging-handle.plate_arc_r","radian-raptor-sd-charging-handle.port_count","radian-raptor-sd-charging-handle.port_pitch","radian-raptor-sd-charging-handle.port_notch_depth","radian-raptor-sd-charging-handle.port_hole_d","radian-raptor-sd-charging-handle.port_floor_rear","radian-raptor-sd-charging-handle.port_floor_front","radian-raptor-sd-charging-handle.port_top_rear","radian-raptor-sd-charging-handle.port_top_front"]},"profiles":{"plan":{"plane":"xz","origin":"the T's shoulder (the front face of the ledge under the T's block, at its lower edge: the dark runs to column 421 of the photo beside the shaft) on the shaft's centre line, +x toward the muzzle, z to the handle's right","offset":{},"points":[[-1.083,-0.252],[-1.076,-0.263],[-1.083,-0.267],[-1.079,-0.274],[-1.083,-0.277],[-1.079,-0.281],[-1.076,-0.361],[-1.069,-0.393],[-1.076,-0.411],[-1.076,-0.469],[-1.072,-0.473],[-1.072,-0.513],[-1.061,-0.564],[-1.047,-0.593],[-1.03,-0.609],[-1.027,-0.605],[-1.012,-0.609],[-0.996,-0.625],[-0.992,-0.658],[-0.996,-0.669],[-0.987,-0.678],[-0.968,-0.678],[-0.948,-0.698],[-0.945,-0.719],[-0.952,-0.738],[-0.947,-0.743],[-0.928,-0.743],[-0.905,-0.763],[-0.901,-0.792],[-0.905,-0.806],[-0.899,-0.812],[-0.885,-0.812],[-0.87,-0.819],[-0.857,-0.835],[-0.861,-0.872],[-0.857,-0.879],[-0.834,-0.884],[-0.814,-0.901],[-0.81,-0.933],[-0.814,-0.948],[-0.683,-1.143],[-0.645,-1.174],[-0.616,-1.185],[-0.525,-1.199],[-0.485,-1.21],[-0.467,-1.21],[-0.427,-1.221],[-0.409,-1.221],[-0.369,-1.232],[-0.318,-1.232],[-0.314,-1.235],[-0.27,-1.224],[-0.234,-1.203],[-0.207,-1.175],[-0.185,-1.128],[-0.189,-1.118],[-0.203,-1.103],[-0.203,-1.085],[-0.189,-1.067],[-0.189,-1.052],[-0.194,-1.047],[-0.216,-1.043],[-0.232,-1.02],[-0.229,-1.002],[-0.214,-0.98],[-0.223,-0.967],[-0.249,-0.96],[-0.258,-0.947],[-0.258,-0.922],[-0.243,-0.9],[-0.249,-0.891],[-0.278,-0.881],[-0.287,-0.864],[-0.287,-0.85],[-0.283,-0.839],[-0.272,-0.828],[-0.272,-0.817],[-0.278,-0.812],[-0.296,-0.808],[-0.312,-0.788],[-0.312,-0.767],[-0.298,-0.745],[-0.307,-0.732],[-0.318,-0.732],[-0.338,-0.719],[-0.345,-0.694],[-0.338,-0.676],[-0.327,-0.669],[-0.33,-0.658],[-0.336,-0.653],[-0.354,-0.649],[-0.37,-0.629],[-0.367,-0.6],[-0.345,-0.582],[-0.349,-0.567],[-0.345,-0.564],[-0.345,-0.524],[-0.338,-0.506],[-0.338,-0.491],[-0.301,-0.415],[-0.289,-0.41],[-0.26,-0.385],[-0.231,-0.374],[-0.172,-0.374],[-0.147,-0.381],[-0.122,-0.381],[-0.096,-0.388],[-0.045,-0.392],[-0.02,-0.399],[0.005,-0.399],[0.114,-0.417],[0.187,-0.418],[0.19,-0.414],[0.354,-0.403],[0.363,-0.398],[0.37,-0.383],[0.359,-0.329],[0.256,-0.233],[0.212,-0.208],[0.212,-0.201],[0.499,-0.201],[0.502,-0.197],[4.537,-0.197],[4.541,-0.2],[4.584,-0.204],[4.634,-0.222],[4.666,-0.24],[4.856,-0.24],[4.914,-0.211],[4.971,-0.197],[5.64,-0.197],[5.648,-0.19],[5.669,-0.19],[5.687,-0.201],[5.791,-0.201],[5.794,-0.205],[5.801,-0.201],[5.855,-0.201],[5.884,-0.187],[5.932,-0.135],[5.953,-0.088],[5.964,-0.049],[5.968,0.012],[5.964,0.016],[5.96,0.063],[5.932,0.131],[5.887,0.183],[5.858,0.197],[5.687,0.198],[5.669,0.183],[5.63,0.194],[5.619,0.201],[5.021,0.198],[5.018,0.202],[4.96,0.202],[4.924,0.209],[4.878,0.227],[4.853,0.245],[4.681,0.246],[4.659,0.242],[4.613,0.217],[4.58,0.206],[4.537,0.199],[0.005,0.201],[0,0.207],[0,0.344],[-0.009,0.342],[-0.02,0.35],[-0.049,0.346],[-0.093,0.353],[-0.249,0.354],[-0.243,0.359],[-0.247,0.366],[-0.292,0.412],[-0.301,0.406],[-0.309,0.431],[-0.33,0.464],[-0.349,0.518],[-0.352,0.569],[-0.356,0.573],[-0.352,0.584],[-0.378,0.609],[-0.374,0.638],[-0.354,0.654],[-0.339,0.654],[-0.334,0.667],[-0.334,0.674],[-0.349,0.689],[-0.349,0.714],[-0.336,0.73],[-0.314,0.734],[-0.309,0.739],[-0.309,0.75],[-0.32,0.761],[-0.323,0.772],[-0.32,0.793],[-0.31,0.806],[-0.285,0.813],[-0.28,0.822],[-0.28,0.83],[-0.294,0.848],[-0.294,0.869],[-0.278,0.889],[-0.254,0.895],[-0.254,0.913],[-0.269,0.931],[-0.269,0.949],[-0.256,0.965],[-0.231,0.972],[-0.225,0.985],[-0.24,1.003],[-0.243,1.025],[-0.227,1.048],[-0.201,1.052],[-0.196,1.065],[-0.214,1.094],[-0.214,1.104],[-0.201,1.124],[-0.191,1.132],[-0.176,1.131],[-0.171,1.141],[-0.171,1.148],[-0.189,1.17],[-0.189,1.188],[-0.172,1.207],[-0.154,1.211],[-0.149,1.227],[-0.152,1.253],[-0.171,1.296],[-0.209,1.338],[-0.241,1.356],[-0.267,1.363],[-0.314,1.363],[-0.55,1.317],[-0.59,1.295],[-0.607,1.279],[-0.817,0.957],[-0.825,0.943],[-0.817,0.932],[-0.821,0.892],[-0.83,0.894],[-0.837,0.887],[-0.865,0.881],[-0.868,0.871],[-0.857,0.852],[-0.865,0.834],[-0.881,0.818],[-0.907,0.815],[-0.912,0.809],[-0.901,0.777],[-0.908,0.773],[-0.921,0.753],[-0.932,0.746],[-0.95,0.746],[-0.959,0.737],[-0.948,0.708],[-0.956,0.701],[-0.956,0.693],[-0.979,0.677],[-0.999,0.675],[-1.003,0.664],[-0.996,0.65],[-0.996,0.632],[-1.007,0.617],[-1.007,0.61],[-1.041,0.608],[-1.061,0.578],[-1.072,0.545],[-1.076,0.494],[-1.079,0.491],[-1.079,0.418],[-1.072,0.407],[-1.076,0.386],[-1.072,0.382],[-1.072,0.331],[-1.076,0.328],[-1.069,0.317],[-1.076,0.31],[-1.072,0.306],[-1.076,0.302],[-1.076,0.219],[-1.072,0.215],[-1.072,0.19],[-1.079,0.165],[-1.076,0.157],[-1.079,0.139],[-1.076,0.121],[-1.079,0.117],[-1.076,0.114],[-1.076,0.041],[-1.079,0.038],[-1.076,0.027],[-1.079,0.02],[-1.072,0.012],[-1.076,0.005],[-1.072,0.002],[-1.072,-0.19],[-1.058,-0.227],[-1.076,-0.238],[-1.079,-0.245],[-1.076,-0.248]],"features":{"windows":[[[-0.796,0.751],[-0.792,0.784],[-0.77,0.827],[-0.719,0.899],[-0.65,1.011],[-0.625,1.044],[-0.625,1.051],[-0.614,1.062],[-0.599,1.091],[-0.588,1.102],[-0.541,1.178],[-0.499,1.212],[-0.379,1.237],[-0.343,1.237],[-0.307,1.219],[-0.294,1.202],[-0.287,1.181],[-0.29,1.134],[-0.309,1.09],[-0.309,1.079],[-0.316,1.068],[-0.32,1.047],[-0.33,1.025],[-0.352,0.953],[-0.359,0.942],[-0.363,0.92],[-0.37,0.909],[-0.414,0.772],[-0.443,0.714],[-0.459,0.698],[-0.499,0.68],[-0.528,0.68],[-0.572,0.691],[-0.627,0.691],[-0.63,0.687],[-0.641,0.691],[-0.699,0.677],[-0.721,0.677],[-0.747,0.684],[-0.761,0.691],[-0.781,0.711]],[[-0.785,-0.77],[-0.785,-0.741],[-0.774,-0.709],[-0.761,-0.696],[-0.736,-0.681],[-0.717,-0.678],[-0.685,-0.678],[-0.612,-0.692],[-0.554,-0.689],[-0.55,-0.685],[-0.485,-0.685],[-0.452,-0.7],[-0.432,-0.719],[-0.407,-0.777],[-0.32,-1.027],[-0.32,-1.056],[-0.33,-1.081],[-0.354,-1.101],[-0.376,-1.109],[-0.427,-1.105],[-0.467,-1.094],[-0.558,-1.08],[-0.594,-1.062],[-0.617,-1.038],[-0.752,-0.839],[-0.752,-0.832],[-0.77,-0.81]]],"catch_gap":[[[0,-0.264],[0,-0.206],[0.005,-0.2],[0.201,-0.2],[0.201,-0.204],[0.185,-0.21],[0.196,-0.257],[0.192,-0.285],[0.172,-0.302],[0.125,-0.305],[0.122,-0.309],[0.089,-0.309],[0.005,-0.291]]],"pins":[[[-0.608,0.444],[-0.597,0.444],[-0.597,0.433],[-0.608,0.433]],[[-0.6,-0.428],[-0.59,-0.428],[-0.59,-0.439],[-0.6,-0.439]]],"ports":[[[3.03,0.105],[3.03,0.127],[3.057,0.147],[3.114,0.15],[3.143,0.14],[3.152,0.131],[3.156,0.113],[3.148,0.095],[3.139,0.086],[3.134,0.087],[3.138,0.095],[3.13,0.098],[3.134,0.105],[3.129,0.107],[3.103,0.096],[3.057,0.1],[3.051,0.095],[3.049,0.082],[3.037,0.091]],[[3.03,-0.125],[3.033,-0.089],[3.046,-0.08],[3.044,-0.086],[3.053,-0.087],[3.053,-0.095],[3.078,-0.087],[3.125,-0.095],[3.139,-0.08],[3.156,-0.104],[3.156,-0.114],[3.152,-0.125],[3.139,-0.138],[3.118,-0.145],[3.067,-0.145],[3.046,-0.138]],[[3.479,0.105],[3.483,0.119],[3.479,0.127],[3.492,0.139],[3.517,0.15],[3.571,0.15],[3.582,0.146],[3.596,0.139],[3.605,0.123],[3.602,0.098],[3.589,0.081],[3.584,0.083],[3.587,0.101],[3.578,0.107],[3.546,0.096],[3.503,0.103],[3.505,0.094],[3.499,0.081]],[[3.479,-0.122],[3.479,-0.093],[3.487,-0.082],[3.496,-0.081],[3.494,-0.09],[3.499,-0.095],[3.517,-0.088],[3.557,-0.084],[3.56,-0.091],[3.571,-0.091],[3.582,-0.099],[3.584,-0.093],[3.576,-0.09],[3.593,-0.081],[3.605,-0.108],[3.602,-0.126],[3.578,-0.142],[3.56,-0.145],[3.524,-0.145],[3.488,-0.131]],[[3.929,0.104],[3.929,0.126],[3.945,0.142],[3.966,0.149],[4.024,0.149],[4.035,0.146],[4.051,0.133],[4.054,0.122],[4.051,0.101],[4.035,0.084],[4.029,0.086],[4.04,0.097],[4.028,0.106],[4.01,0.099],[3.959,0.099],[3.952,0.103],[3.954,0.097],[3.947,0.094],[3.95,0.086],[3.941,0.085]],[[3.929,-0.122],[3.932,-0.086],[3.938,-0.081],[3.948,-0.081],[3.954,-0.086],[3.945,-0.088],[3.945,-0.092],[4.01,-0.088],[4.031,-0.099],[4.036,-0.09],[4.029,-0.083],[4.042,-0.081],[4.054,-0.108],[4.051,-0.122],[4.035,-0.139],[4.01,-0.146],[3.974,-0.146],[3.938,-0.131]],[[4.378,0.104],[4.378,0.125],[4.404,0.145],[4.451,0.152],[4.483,0.145],[4.5,0.133],[4.503,0.111],[4.487,0.088],[4.489,0.097],[4.476,0.109],[4.451,0.098],[4.404,0.102],[4.395,0.097],[4.403,0.093],[4.394,0.084],[4.385,0.089]],[[4.374,-0.105],[4.381,-0.087],[4.39,-0.078],[4.395,-0.087],[4.39,-0.096],[4.426,-0.085],[4.444,-0.085],[4.476,-0.096],[4.487,-0.081],[4.5,-0.094],[4.503,-0.108],[4.5,-0.126],[4.473,-0.143],[4.412,-0.143],[4.394,-0.135],[4.378,-0.119]],[[4.826,0.1],[4.826,0.129],[4.835,0.137],[4.86,0.148],[4.903,0.152],[4.932,0.145],[4.944,0.136],[4.948,0.107],[4.932,0.087],[4.926,0.089],[4.93,0.1],[4.924,0.109],[4.892,0.098],[4.867,0.098],[4.838,0.105],[4.847,0.096],[4.84,0.093],[4.842,0.08]],[[4.826,-0.12],[4.829,-0.084],[4.835,-0.078],[4.84,-0.084],[4.837,-0.087],[4.838,-0.096],[4.881,-0.082],[4.917,-0.093],[4.932,-0.103],[4.933,-0.087],[4.942,-0.089],[4.948,-0.098],[4.948,-0.12],[4.935,-0.136],[4.921,-0.143],[4.863,-0.143],[4.838,-0.132]],[[5.27,0.121],[5.293,0.144],[5.326,0.151],[5.354,0.151],[5.372,0.148],[5.392,0.135],[5.395,0.11],[5.379,0.09],[5.374,0.106],[5.381,0.113],[5.376,0.115],[5.351,0.101],[5.333,0.097],[5.29,0.105],[5.29,0.083],[5.274,0.099]],[[5.27,-0.113],[5.277,-0.08],[5.286,-0.075],[5.299,-0.084],[5.293,-0.089],[5.347,-0.086],[5.376,-0.1],[5.381,-0.098],[5.377,-0.091],[5.383,-0.093],[5.381,-0.084],[5.386,-0.082],[5.395,-0.098],[5.392,-0.127],[5.361,-0.143],[5.318,-0.143],[5.286,-0.133]]]},"scaleRefs":["radian-raptor-sd-charging-handle.shaft_width"],"inputs":{"radian-raptor-sd-charging-handle.shaft_width":0.4},"tolerance":0.003,"photo":"references/radian-raptor-sd-charging-handle b55302018bd7 (Primary Arms: the black R0006 from below, on white, 2200 x 1467 (R0006_01))","method":"luminance < 82, largest piece, holes filled; scale from radian-raptor-sd-charging-handle.shaft_width = 0.4 in, the tube's own width column by column: 110.8 px over columns 560–900, 110.8 px over columns 950–1230, 111.1 px over columns 1960–2030; a line through them (rms 0.20 px) changes +0.7% from column 560 to 2030, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 277.3 px/in there. The axis is the tube's centre line (tilt -0.06°, rms 0.16 px); origin at column 421.5 of the photo, on the tube's axis; Douglas-Peucker at 0.003 in with the extremes kept: 301 points (IoU 0.995 with the full outline); Seen from below, the muzzle to the right: the handle's right side is up in the photo. The same set-up as Primary Arms' photos of the Raptor and the Raptor-LT from below (the shaft 110 px wide). The latches' front faces and the windows' walls show as grey bands, left out of the mask, so the outline is the lower faces' edges.; checks: x_max 5.968 ± 0.084 in vs radian-raptor-sd-charging-handle.length 5.895 ± 0.01 (confirmed): agrees; height in x [4.66, 4.86] 0.486 ± 0.013 in vs radian-raptor-sd-charging-handle.guide_lug_width 0.488 ± 0.005 (confirmed): agrees; features through the same placement (windows: the opening through each latch, at its lower face; catch_gap: the gap between the latch's hook arm and the shaft's left side, closed at its front by the hook's tooth; pins: the two pivot pins' lower ends, each a 3 px square about the bright end's centre (255.6, 610.1 and 257.7, 851.0: the weighted centre of what is over 150 of 255 within 25 px); ports: the twelve ports seen through from below (each 45-degree hole through the shaft's top corner, seen down the open key channel): what shows white of each, six along each side; their centres are where the holes are along the shaft) (tools/trace.py)","via":"harvest","note":"From below: the shaft with its nose and guide lugs, the ledge under the T's block (the shoulder), the latch's hook on the left, the two latches with their teeth, the T's rear; the ports' holes seen through the key's channel."}},"gaps":[{"what":"Radian's own figures","need":"Radian's page (read now) states no size and no weight: the weight is two sellers' 1.38 oz against a reviewer's and a seller's 1.3 (the ledger's conflict); no length, width or height is a maker's."},{"what":"The T's top from above, traced","need":"The plate's outline (its ears round the pins, its arc), the opening the latches leave round it and the logo, picked on Primary Arms' photo of the T from above (e7de8e1a93bd) and carried into the plan by the two pins: until then the plate is the block's width behind a circle through its arc, and round each pin."},{"what":"A straight view of the left side and the rear","need":"A photo or render square to the left side (the hook arm's two heights, read here on the design patent) and to the T's rear (the plates and the latches' tongues)."},{"what":"The ports' exact form","need":"The ports' walls and holes are read on two renders and the patent's sketch; a drawing or a close photo square to a port's face would give the hole's place on the face and the walls' rounds."},{"what":"Its seat checked on a photo of it in a receiver","need":"A pin-framed photo of the handle latched in an upper: it is placed with its shoulder against the front wall of the receiver's notch, as the Army's handle stops. Wing Tactical says it \"May NOT fit on some SIG ARs, specifically the 516 Model\": no SIG receiver is in the catalog."}]},"radian-talon-safety-selector":{"id":"radian-talon-safety-selector","name":"Talon 45/90 - 2 Lever Kit","manufacturer":"Radian Weapons","sku":"R0018","url":"https://radianweapons.com/product/talon-4590-2-lever-kit","category":"selector","description":"An ambidextrous safety selector: a lever on each side of the rifle, a long one and a short one, each slid onto a dovetail on the shaft's end and held by a sprung stud. Radian: \"The Talon™ 45/90 ambidextrous safety selector is a modular design that can be installed as a standard 90° or as a 45° short throw by simply rotating the shaft 180° inside the lower receiver. Selector levers install using a precision machined dovetail interface with spring-loaded retention stud to lock the lever in place – no screws to come loose or break.\" The kit: \"1 - TALON Cylinder, 1 - Short Lever, 1 - Long Lever, 2 - TALON Spring & Detents, 1 - Talon Tool, 1 - Safety Selector Detent, 1 - Safety Selector Detent Spring\".","weight":"radian-talon-safety-selector.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"selector":{"origin":[0,0,0],"note":"Selector frame: on its axis, at the middle of the shaft (the receiver's mid-plane when it is in), with the selector on SAFE: +x toward the muzzle, +y up, +z out of the rifle's right side. Each lever's inner face lies in a shoulder of the shaft, half the shaft's length (radian-talon-safety-selector.shaft_length) from here: the long lever's toward -z, the left side, the short one's toward +z. That is .04 beyond a standard receiver's side each way (std.ar15.lower_body_width): the levers don't bear on the receiver, by the photos' reading."}},"interfaces":{"selector":{"type":"ar15.selector","role":"selector","anchor":"selector","params":{},"flips":false,"note":"Radian: \"The Talon is compatible with most semi-automatic AR15 & AR10/SR25-pattern rifles as well as MCX and MPX platforms.\" (https://radianweapons.com/product/talon-4590-2-lever-kit). The throw is the builder's choice, 90° or 45°: \"installed as a standard 90° or as a 45° short throw by simply rotating the shaft 180° inside the lower receiver\"; to change it, \"Loosen the grip just enough to rotate the entire safety unit 180°, then tighten grip.\" and \"Remove the levers using the supplied installation tool, then reinstall the levers in the correct orientation.\" Nothing is posed by it: the selector is drawn on SAFE, both thumb pieces back over the grip, which is how a lever on the left lies on SAFE at either throw (a buyer's photo of one on an Aero lower's left side, the marks in frame: references/radian-talon-safety-selector d66a7d77d01c). Which lever goes on which side is the builder's too: drawn with the long lever on the left and the short on the right, as two buyers' photos have them (d66a7d77d01c, the left side, the long one; fcf153b44108, the right side, the short one). A buyer, of the short one: \"The ability to reverse the off-side lever so it doesn't rub your trigger finger is a blessing too\" (Primary Arms' reviews): the right lever can also be put on pointing forward, which isn't drawn. It comes with its own detent and detent spring (\"Drop the supplied safety detent into the lower receiver and place the supplied safety detent spring into the grip.\")."}},"materials":{"levers":{"label":"Levers","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black Anodized","finish":"anodized_matte","color":"placeholder-black","sku":"R0018","source":"https://www.primaryarms.com/radian-weapons-talon-ambidextrous-safety-selector-2-lever-kit-r0018"},"fde":{"label":"Flat Dark Earth","finish":"anodized_matte","color":"radian-fde","sku":"R0020","source":"https://www.midwestgunworks.com/page/mgwi/prod/talon-2-lever"},"od":{"label":"Radian OD","finish":"anodized_matte","color":"radian-od","sku":"R0381","source":"https://www.midwestgunworks.com/page/mgwi/prod/talon-2-lever"},"grey":{"label":"Radian Grey","finish":"anodized_matte","color":"radian-grey","sku":"R0567","source":"https://www.midwestgunworks.com/page/mgwi/prod/talon-2-lever"}},"default":"black","note":"The two levers: what the kit's colour is the colour of. \"Levers Machined from Billet aircraft grade aluminum w Milspec Type 3 Hard Coat Anodized Finish or Cerakote\" (Radian); \"Finish Hardcoat Anodized\", \"Color Black\" (Primary Arms, of R0018); \"Lever: Anodized, Cerakote, or NP3\" (Wing Tactical). No page says which colours are anodized and which Cerakote: all are drawn as a matte anodize, in Radian's colours as they were matched on its charging handle's latches (data/colors/radian.yaml), not matched again on this part: on Midwest Gun Works' pictures a lever's flat reads #92826b (FDE), #6e7058 (Radian OD) and #4e4e4e (Radian Grey), within 5, 18 and 12 levels of the photos those three colours were fitted to on the handle, and those pictures are one picture recoloured. Radian's own colour list for this kit: \"Black Anodized, Flat Dark Earth, Radian OD, Radian Grey, Clear Ano\". The four numbers are Midwest Gun Works' table (\"SKU COLOR R0018 Black R0020 FDE R0381 Radian OD R0567 Radian Grey\"), whose four pictures are named by them (8b0257c89156, de0ad56d62ac, 17d042c1390c, ecad68fec1b2: one picture in four colours, the levers alone changed). Sold and not offered here: Clear Ano is now identified as R0141 by the maker's public product API (2026-10-28), which also names its exact image URL; that S3 host refuses robots.txt with HTTP 403, so the current variant's piece colours remain unverified. Still lacking confirmed identity and appearance: Tungsten Grey R0019 and Brown R0021 (sellers' titles; AR15Discounts' pictures f09f2e97cdaa and 3981f16b74c3), a \"Grey\" at AR15Discounts whose number no page gives, and Red and NP3 at Wing Tactical (R0233: perhaps Radian's Competition kit, a sibling)."},"shaft":{"label":"Shaft","finish":"nitride","recolorable":false,"color":"steel-nitride-black","note":"\"Center Shaft Machined from Hardened Steel w/ Black Nitride Finish\" (Radian); \"Center Shaft: Black Nitride\" (Wing Tactical). Black on every colour of lever (Midwest Gun Works' four pictures, AR15Discounts' six, Wing Tactical's tan kit laid out). What shows of it on a rifle is its two dovetails' ends in the levers' heads."},"studs":{"label":"Retention studs","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"The sprung stud in each end of the shaft, whose tip stands in the hole in the lever's head: bright steel beside the black levers and the tan ones (Primary Arms' black kit laid out, 21ba32f12fa4; Wing Tactical's tan one, a241d3bad91d), a bright dot in a lever's head on a rifle (fcf153b44108). Not named a material by any page; drawn as bare stainless."}},"components":{},"geometry":{"model":"radian-talon-safety-selector.glb","components":{},"approximations":["No size of it is published: every figure is read from two sellers' photographs (Primary Arms' black kit laid out flat; AR15Discounts' picture with the long lever on the shaft edge-on), each scaled by the shaft's own diameter, which is not Radian's figure but the Army's selector's (.3730 -.0015): the shaft turns in the same hole. Good to about 1% between the two photos, and no better than that assumption.","The levers' inner faces are in the shaft's two shoulders, .961 apart, so each stands .04 off a standard receiver's side (.88 wide) with the selector centred, as its detent would hold it. That gap is the photos' reading (the shoulders are 2.58 of the shaft's diameters apart in both), not a sentence of Radian's.","The short lever is seen only face-on: its edge-on form (the head's slope, the thumb piece's step, flat top and taper, its three grooves a side) is the long lever's, which the three-quarter views show it shares, carried to its own length.","Each lever's head is drawn as its middle band, sloped as the edge-on view has it, with a flat facet falling from the band to the rim on either side; the real facets are scooped hollow. The groove down the head's face and the grooves along the thumb piece's sides are drawn half as deep as they are wide (round-ended cuts whose depth no photo gives).","The shaft inside the receiver is a plain cylinder: the cut for the trigger's tail, the two detent grooves that give the 90 and the 45 degree throw, and the studs' bores aren't drawn (none of it shows). The studs are drawn as their tips in the levers' holes; their springs, the detent, its spring and the tool that come in the kit aren't drawn.","Drawn on SAFE with both thumb pieces back, the long lever on the left; the 45 degree throw, the short lever on the left, and the off-side lever turned forward are the builder's choices and aren't posed."],"ledger":["radian-talon-safety-selector.shaft_d","radian-talon-safety-selector.shaft_length","radian-talon-safety-selector.dovetail_height","radian-talon-safety-selector.dovetail_width_top","radian-talon-safety-selector.dovetail_width_base","radian-talon-safety-selector.head_d","radian-talon-safety-selector.lever_width","radian-talon-safety-selector.lever_reach","radian-talon-safety-selector.short_lever_reach","radian-talon-safety-selector.lever_standoff","radian-talon-safety-selector.head_t_top","radian-talon-safety-selector.head_t_shelf","radian-talon-safety-selector.head_rim_t","radian-talon-safety-selector.shelf_start","radian-talon-safety-selector.shelf_end","radian-talon-safety-selector.shelf_ramp","radian-talon-safety-selector.lever_chamfer","radian-talon-safety-selector.shelf_point_length","radian-talon-safety-selector.head_band_w","radian-talon-safety-selector.lever_tip_t","radian-talon-safety-selector.tip_rake","radian-talon-safety-selector.tip_flat","radian-talon-safety-selector.neck_fillet_r","radian-talon-safety-selector.stud_hole_d","radian-talon-safety-selector.groove_pitch","radian-talon-safety-selector.groove_first","radian-talon-safety-selector.groove_width","radian-talon-safety-selector.groove_start","radian-talon-safety-selector.groove_end_from_tip","radian-talon-safety-selector.head_groove_w","std.ar15.selector_hole_d","std.ar15.lower_body_width"]},"profiles":{},"gaps":[{"what":"every size: none is published, and all are read from photos scaled by an assumed shaft diameter","need":"a maker's or reviewer's figure for any one length of it (a lever's length, the shaft between its shoulders), or a photo of it on a rifle square-on with the pins in frame"},{"what":"its weight by a scale: the maker states none and four sellers' figures run from 0.04 oz to 1.92 oz","need":"a weighed figure for the shaft with its two levers"},{"what":"whether its levers stand off the receiver's sides (.04 a side by the photos)","need":"a view along the rifle of one installed"},{"what":"the scoop of the head's side facets and the depth of its grooves","need":"a close view of a lever's head from its top edge"}]},"reptilia-aus-30mm-mount":{"id":"reptilia-aus-30mm-mount","name":"AUS™ MOUNT - 30MM DIAMETER - 39MM HEIGHT","manufacturer":"Reptilia","sku":"100-116","url":"https://reptiliacorp.com/product/aus-optic-mount-30mm-diameter-39mm-height/","category":"scope_mount","description":"Reptilia's one-piece scope mount for a 30 mm tube: \"30mm diameter bore\", \"39mm (1.54 inch) bore height\", \"158 grams\", \"Machined from billet 7075-T6 aluminum\". It \"attaches to any M1913 Picatinny rail via our anti-snag spring-loaded nitrided steel clamp and custom bolt mounting system which can be tightened with either a 5/32 hex or a flat blade driver to sit flush with the body of the mount\". The scope slides in its two rings before their caps are tightened.","weight":"reptilia-aus-30mm-mount.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":["{.rail_index_x}",0,0],"note":"On the rail's top over the middle of the slot the build names: three slots behind the recoil lug's, which is what seats the mount along the rail (\"apply a slight forward pressure toward muzzle\"). The rear cross bolt lies in that slot 0.03 in behind its middle and the front one, six slots ahead, as far ahead of its own: the two are 2.41 in apart, not a whole number of slots."},"rings":{"origin":["({.ring_rear_x} + {.ring_front_x}) / 2","{.optical_axis_above_rail}",0],"note":"On the rings' axis midway between the two rings: where a scope's saddle is put at position 0."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":"={.rail_index_x}","clamp_front":"={.clamp_bolt_spacing} - {.rail_index_x}","cross_rear":"={.rail_index_x}","cross_front":"={.clamp_bolt_spacing} - {.rail_index_x}"},"flips":false,"note":"Two cross bolts 2.41 in apart (45 in-lb, dry: the maker's installation sheet), from the rear one, just behind the anchor, to the front one: it is clamped over seven slots, with its lug in the middle one. The front ring stands 1.85 in ahead of the front bolt, over whatever is ahead of the clamp. The maker says only that it \"attaches to any M1913 Picatinny rail\"; nothing it publishes says where along a rail."},"rings":{"type":"scope_rings","role":"rings","anchor":"rings","params":{"diameter":"={.ring_bore}","rear_ring":"=({.ring_rear_x} - {.ring_front_x}) / 2","front_ring":"=({.ring_front_x} - {.ring_rear_x}) / 2","ring_length":"={.ring_length}"},"flips":false,"note":"Two rings bored 30 mm (\"30mm diameter bore\"; engraved \"30MM Ø · 39MM HEIGHT\"), 3.62 in apart middle to middle and 0.78 long each: 2.85 in between their faces for a scope's saddle. Four upright T15 screws to a cap (15 in-lb, dry)."}},"materials":{"body":{"label":"Mount","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized_matte","color":"placeholder-black","sku":"100-116","source":"https://reptiliacorp.com/product/aus-optic-mount-30mm-diameter-39mm-height/"},"fde":{"label":"Flat Dark Earth","finish":"anodized_matte","color":"reptilia-fde","sku":"100-122","source":"https://reptiliacorp.com/product/aus-optic-mount-30mm-diameter-39mm-height/"},"clear":{"label":"Clear Anodize","finish":"anodized_matte","color":"reptilia-clear","sku":"100-118","source":"https://reptiliacorp.com/product/aus-optic-mount-30mm-diameter-39mm-height/"}},"default":"black","note":"Reptilia: \"MIL-STD, Type III, hardcoat anodized\", \"finished with MIL-STD Type III, Class 2, hard anodize coating\". Its original 30mm/39mm mount is sold in Black Anodize (100-116), Clear Anodize (100-118) and Flat Dark Earth Anodize (100-122). Black uses the matte finish seen in Milgear's photographs; its black is not photo-fitted. FLAT DARK EARTH (100-122) is offered since 2026-10-19 in reptilia-fde, fitted to Silencer Shop's actual studio photo 0bf480654d9e. The maker's FDE on-rifle image and its seller copies are recoloured artwork, not used for that fit. CLEAR (100-118) is offered since 2026-10-28 in reptilia-clear, fitted to the maker's separate oblique and top photographs eeb891756f2e and bf5ec607d063. Its natural hardcoat appears olive bronze with warmer gold lit faces, not silver. Clear remains unpriced: no offer from a seller in data/vendors.yaml is on file; the maker's Q exclusivity sentence and the current Sportsman's Outdoor Superstore 100-118 listing establish identity, not a catalog price. Piece map in the clear photographs and Milgear's black views: base, necks, rings, caps and recoil lug are the body's anodize; both clamps, both cross bolts and all cap screws remain black steel in the hardware slot. The FDE clamps' hidden right side is still inferred from these views, as the existing gap states. White engraving and the cap logo are not drawn. OD Green 100-312 is sold but NOT OFFERED as a color of this model: the current maker page describes T25 cross bolts, and its 100-312-AUS-MOUNT-30mm-39mm-ODG-3.jpg clearly shows star sockets, whereas this model and the Clear photographs have hex sockets. That revised visible hardware is a separate model-identity task, not a recolor."},"hardware":{"label":"Clamps","finish":"nitride","recolorable":false,"color":"steel-nitride-black","note":"The two clamps on the right, the two cross bolts' heads on the left and the eight ring cap screws: black steel on the clear mount's photographs and a blacker, glossier black than the anodize on Milgear's of the black one. Reptilia: \"anti-snag spring-loaded nitrided steel clamp\". The bolts' and the screws' own coat isn't said on a page on file: drawn as the clamps'."}},"components":{"body":{"label":"Mount","material":"body"},"hardware":{"label":"Clamps","material":"hardware"}},"geometry":{"model":"reptilia-aus-30mm-mount.glb","components":{},"approximations":["Its scale is one published length: a Finnish shop's 135 mm, which the launch photo of the mount with a scope in it reads within a quarter of a percent by the maker's own 39 mm. No drawing, no end-on view and no other length is published: every other size is a reading on a photograph, most of them 640 px wide, good to a hundredth or two of an inch (the ledger gives each its ±).","The base, the bridge, the necks under the rings and the tail are the left side view's outline, from the rail's top up to the necks' tops, drawn as wide as the plate (0.71 in); between the rings only a web 0.19 in wide stands above the plate's top (its lettered faces: the engraving isn't drawn), and the tail's end block is as wide as a rail. How the necks and the web blend into one another across the mount isn't read: their ends are square.","Each ring is a section read off the side view's heights and the plan views' widths: a top flat 0.80 in across, a chamfer down to side flats 1.76 apart, the line between cap and lower half 0.11 in above the tube's middle (a groove, not a slit through), a lower chamfer in to the neck. The foot of that chamfer is in shadow in both side views: it is drawn where its slope, read at the cap screws' holes, meets the neck's width. The four cap screws are upright in bores that open on the cap's chamfer and come out through the lower one; their heads' depth down the bores is assumed, and each head is drawn six tenths of its width tall.","The two clamp bosses (the fixed jaws under the bolts' heads) are blocks with chamfered ends, 0.29 in up from the rail's top, where the photos have each flaring out in a concave round at its ends and relieved round its head; the two steel clamps are blocks with chamfered ends where they are faceted. Each bolt's head is drawn flush in a round seat (the maker's word), 0.10 in thick (assumed), with its 5/32 hex socket 0.06 in deep (assumed); the slot across it isn't drawn; each bolt's end stands a sixth of its width out of its clamp. Every machined edge is broken by 0.006 in (assumed).","The cross bolts' shanks across the rail's place aren't drawn: their size isn't read (the view from below shows the groove each lies in, 0.22 in wide, wider than a rail's slot). The groove is cut; what crosses under the rail's top in the model is the recoil lug alone.","The rail's place under the bosses and the clamps is the rail's own head in section (MIL-STD-1913's) from the rail's top down to the lower gauge line, the bosses on the left and the clamps on the right, and plain walls below that, not the jaws' hooks. The mount's underside is drawn bearing on the rail's top.","The accessory pocket in each side of each neck (two cross holes: what the maker's ROF mounts bolt to) is cut 0.12 in deep (assumed) with its corners cut, where they are round; the three lightening pockets and the round one in the underside are cut 0.12 in deep (assumed), their ends read by eye on a gridded picture.","As drawn it is 3.01 cubic inches of 7075 and 0.19 of steel: 163 g for the maker's 158 (3% over, before the cross bolts' shanks and springs, which aren't drawn)."],"ledger":["reptilia-aus-30mm-mount.optical_axis_above_rail","reptilia-aus-30mm-mount.ring_bore","reptilia-aus-30mm-mount.ring_rear_x","reptilia-aus-30mm-mount.ring_front_x","reptilia-aus-30mm-mount.ring_length","reptilia-aus-30mm-mount.ring_width","reptilia-aus-30mm-mount.overall_length","reptilia-aus-30mm-mount.clamp_bolt_spacing","reptilia-aus-30mm-mount.mount_length","reptilia-aus-30mm-mount.base_width","reptilia-aus-30mm-mount.lug_x"]},"profiles":{"side":{"plane":"xy","origin":"on the rail's top (the mount's underside between its clamp bosses) under the rear cross bolt: the part frame","offset":{},"points":[[-0.66,0.172],[-0.66,0.038],[-0.646,0.024],[-0.617,0.024],[-0.608,0.014],[-0.588,0.024],[-0.56,0.014],[-0.526,-0.01],[-0.507,-0.038],[-0.507,-0.191],[-0.455,-0.234],[-0.263,-0.234],[-0.254,-0.253],[0.158,-0.253],[0.167,-0.244],[0.492,-0.244],[0.497,-0.22],[0.526,-0.182],[0.526,-0.057],[0.54,-0.033],[0.578,-0.033],[0.588,-0.024],[0.617,-0.024],[0.626,-0.033],[0.636,-0.024],[0.684,-0.024],[0.703,-0.005],[1.095,-0.005],[1.105,0.005],[1.119,-0.01],[1.119,-0.067],[1.143,-0.1],[1.282,-0.105],[1.181,-0.11],[1.181,-0.12],[1.353,-0.12],[1.363,-0.005],[1.831,-0.005],[1.841,-0.014],[1.879,-0.024],[1.894,-0.048],[1.894,-0.163],[1.903,-0.172],[1.903,-0.191],[1.946,-0.225],[2.051,-0.225],[2.061,-0.244],[2.348,-0.244],[2.358,-0.234],[2.501,-0.234],[2.511,-0.225],[2.874,-0.225],[2.917,-0.182],[2.917,-0.057],[2.927,-0.038],[2.941,-0.024],[2.97,-0.024],[3.008,-0.005],[3.496,-0.005],[3.505,0.005],[3.572,0.005],[3.582,0.014],[3.639,0.014],[3.649,0.024],[3.706,0.024],[3.716,0.033],[3.831,0.043],[3.84,0.053],[3.898,0.053],[3.907,0.062],[3.965,0.062],[3.974,0.072],[4.031,0.072],[4.041,0.081],[4.108,0.081],[4.118,0.091],[4.184,0.091],[4.194,0.1],[4.242,0.1],[4.251,0.11],[4.338,0.11],[4.347,0.12],[4.376,0.12],[4.385,0.129],[4.404,0.129],[4.424,0.158],[4.443,0.158],[4.452,0.167],[4.471,0.167],[4.51,0.187],[4.548,0.225],[4.558,0.225],[4.591,0.268],[4.62,0.325],[4.62,0.363],[4.629,0.373],[4.62,0.756],[4.629,0.765],[4.629,0.957],[4.639,0.966],[4.648,1.31],[4.658,1.32],[4.658,1.597],[4.648,1.607],[4.648,1.645],[4.658,1.655],[4.658,1.865],[4.648,1.875],[4.648,1.942],[4.639,1.951],[4.639,1.999],[4.629,2.009],[4.629,2.066],[4.62,2.076],[4.62,2.123],[4.61,2.133],[4.61,2.181],[4.601,2.19],[4.601,2.21],[4.577,2.224],[3.878,2.224],[3.855,2.21],[3.845,2.19],[3.845,2.133],[3.855,2.123],[3.855,2.085],[3.835,2.076],[3.826,2.056],[3.826,1.99],[3.816,1.98],[3.816,1.808],[3.807,1.798],[3.807,1.291],[3.816,1.282],[3.816,1.062],[3.826,1.052],[3.826,0.928],[3.835,0.918],[3.835,0.756],[3.807,0.698],[3.745,0.627],[3.73,0.622],[3.725,0.607],[3.639,0.56],[3.611,0.56],[3.601,0.55],[3.544,0.55],[3.534,0.54],[1.363,0.54],[1.353,0.55],[1.315,0.55],[1.305,0.56],[1.286,0.56],[1.277,0.569],[1.238,0.579],[1.157,0.641],[1.157,0.65],[1.128,0.679],[1.109,0.717],[1.109,0.737],[1.1,0.746],[1.1,0.765],[1.109,0.775],[1.109,0.842],[1.119,0.851],[1.119,0.995],[1.128,1.004],[1.128,1.129],[1.138,1.138],[1.138,1.712],[1.128,1.722],[1.128,1.875],[1.119,1.884],[1.119,1.99],[1.109,1.999],[1.109,2.104],[1.1,2.114],[1.09,2.162],[1.071,2.181],[1.071,2.2],[1.057,2.214],[0.349,2.214],[0.315,2.181],[0.315,2.143],[0.306,2.133],[0.296,2.047],[0.287,2.037],[0.287,1.99],[0.277,1.98],[0.277,1.942],[0.268,1.932],[0.268,1.894],[0.258,1.884],[0.258,1.253],[0.268,1.243],[0.268,1.138],[0.277,1.129],[0.277,1.023],[0.287,1.014],[0.287,0.899],[0.296,0.89],[0.296,0.689],[0.287,0.679],[0.287,0.65],[0.248,0.583],[0.21,0.545],[0.21,0.536],[0.196,0.531],[0.148,0.483],[0.052,0.435],[0.033,0.435],[0.005,0.416],[-0.043,0.407],[-0.072,0.387],[-0.12,0.378],[-0.148,0.359],[-0.196,0.349],[-0.225,0.33],[-0.273,0.32],[-0.302,0.301],[-0.378,0.282],[-0.407,0.263],[-0.455,0.253],[-0.483,0.234],[-0.502,0.234],[-0.512,0.225],[-0.569,0.225],[-0.579,0.215],[-0.617,0.215],[-0.636,0.196],[-0.646,0.196]],"scaleRefs":["reptilia-aus-30mm-mount.tail_behind_rear_bolt","reptilia-aus-30mm-mount.front_face_x"],"inputs":{"reptilia-aus-30mm-mount.front_face_x":4.655,"reptilia-aus-30mm-mount.tail_behind_rear_bolt":0.66},"tolerance":0.005,"photo":"references/reptilia-aus-30mm-mount 65d1a1c3c68d (Soldier Systems stkl3530-3.jpg: the clear AUS mount alone, straight left side, 640 x 427)","method":"luminance < 200, largest piece, holes filled; frame from the reviewed holes tail_end, front_face (104.5 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.005 in with the extremes kept: 231 points (IoU 0.999 with the full outline); checks: width 5.318 ± 0.032 in vs reptilia-aus-30mm-mount.overall_length 5.31496 ± 0.019685 (corroborated): agrees; y_max 2.224 ± 0.016 in vs reptilia-aus-30mm-mount.ring_top_above_rail 2.222 ± 0.012 (provisional): agrees; −y_min 0.253 ± 0.014 in vs reptilia-aus-30mm-mount.jaw_below_rail 0.239 ± 0.012 (provisional): agrees (tools/trace.py)","via":"harvest","note":"The mount's left side, turned to face +x: both rings with the far wall of each bore showing beside its near face (toward the middle), the bridge, the base with its underside raised under the front ring, the two clamp bosses and the lug under it, the ramped tail. The model takes the base, the bridge, the necks and the tail from it; the rings are built from their own readings."}},"gaps":[{"what":"A length, a ring spacing or a drawing from the maker","need":"Reptilia publishes a bore, a height, a weight and an objective size and nothing else; its installation sheet is words only. The scale rests on one shop's unlabelled 135 mm and the maker's 39 mm read in a 640 px photo: good to about 1.5%"},{"what":"A view from the end (a bore as a circle), or square across the mount","need":"none on any page read: the rings' section, the bosses' and the clamps' shapes across the rail come from the views from above and below, each scaled at its own depth"},{"what":"The flat dark earth mount's right side (its clamps) and its colour under another light","need":"the one photograph of it on file (Silencer Shop's, 0bf480654d9e) is of the left side, lit from the left: its clamps are drawn as on the clear and black mounts (black steel), and its colour is fitted to that one lit flank"},{"what":"An offer from a catalog seller for Clear Anodize (100-118)","need":"Clear is appearance-matched and selectable since 2026-10-28 but unpriced. The maker and Sportsman's Outdoor Superstore confirm the product; none of its sellers is on file, and no black/FDE offer is assigned to it."},{"what":"The cross bolts' own diameter, and the springs behind the clamps","need":"a picture of a clamp taken off, or the maker's parts list"},{"what":"Whether the cross bolts are 2.41 in apart, as three views read them at the scale the length sets, or six slots (2.364): a conflict kept in the ledger","need":"a published length from the maker, or a photo of the mount on a rail square on with slots in its plane: scaled by six slots the mount would be 132 mm long and its rings' axis 38.2 mm above its underside. Searched for again on 2026-10-19 (sellers' and reviewers' pages): every picture of it on a rail is the maker's one from the front right and above"},{"what":"Where along a rail the maker means it to go","need":"its installation sheet says only to push it forward on the rail; its picture has both clamps on the receiver and the front ring over the handguard"}]},"reptilia-dot-mount-193":{"id":"reptilia-dot-mount-193","name":"DOT MOUNT FOR AIMPOINT® MICRO – 1.93″ HEIGHT","manufacturer":"Reptilia","sku":"100-037","url":"https://reptiliacorp.com/product/dot-mount-for-aimpoint-t-1-t-2-compm5-193-height/","category":"optic_mount","description":"Reptilia's one-piece red dot mount for the Aimpoint Micro footprint: \"Machined from billet 7075-T6 aluminum with Milspec Type III hard anodized finish, the 1.93 DOT Mount attaches to any M1913 Picatinny rail to place the optical axis at 1.93 inches above the rail. Its spring-loaded nitrided steel clamp and mounting bolt simplify the installation process, and sit flush with the body of the mount for a low-profile, anti-snag design.\" 55 grams. The page is headed \"DOT Mount for Aimpoint T-1/T-2/CompM5 – 1.93″ Height\" and every photograph on it has a CompM5 on the mount.","weight":"reptilia-dot-mount-193.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":[0,0,0],"note":"Mount frame: origin on the rail's top under the middle of the base's length, +x forward. The cross bolt's head is there in every left view (its seat's middle within 0.01 in of the base's), 0.003 in over the rail's top by the outline's foot (bolt_above_foot less clamp_below_rail)."},"deck":{"origin":["{.deck_x}","{.deck_above_rail}",0],"note":"On the deck's floor between its lips, at the footprint's middle: where a Micro dot's base is put (D101). The lips stand lip_height over it at the deck's long edges."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":"={.mount_length} / 2","clamp_front":"={.mount_length} / 2"},"flips":false,"note":"The base's length about its middle, where its one cross bolt is. The maker says only that it \"attaches to any M1913 Picatinny rail\": nothing it publishes says where along a rail, or of the receiver's rail against the handguard's."},"deck":{"type":"optic_footprint","role":"deck","anchor":"deck","params":{"pattern":"aimpoint_micro"},"flips":false,"note":"Cut for the Aimpoint Micro: the maker's title (\"DOT MOUNT FOR AIMPOINT® MICRO\"), its heading \"DOT Mount for Aimpoint T-1/T-2/CompM5 – 1.93″ Height\", and \"Compatible with: Aimpoint® – Micro R-1, H-1, H-2, T-1, T-2, CompM5\" (data/interfaces.yaml, optic_footprint)."}},"materials":{"body":{"label":"Mount","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black Anodized","finish":"anodized_matte","color":"placeholder-black","sku":"100-037","source":"https://reptiliacorp.com/product/dot-mount-for-aimpoint-t-1-t-2-compm5-193-height/"},"fde":{"label":"Flat Dark Earth Anodized","finish":"anodized_matte","color":"reptilia-dot-fde","sku":"100-038","source":"https://reptiliacorp.com/product/dot-mount-for-aimpoint-t-1-t-2-compm5-193-height/"}},"default":"black","note":"Reptilia: \"Machined from billet 7075-T6 aluminum with Milspec Type III hard anodized finish\", \"Type III hardcoat anodized 7075 aluminum\". The page sells it in Black Anodized, Flat Dark Earth Anodized and Clear Anodized; its markup names Black 100-037 and Flat Dark Earth 100-038 (the page's own numbers, pmwDataLayer), and Clear none: \"Clear anodized DOT Mounts sold exclusively by Q at LiveQordie.com\". CLEAR is sold and NOT OFFERED: no page on file gives it a number (the maker's gallery file 100-042-SIZED-FOR-SITE-2.jpg is a recoloured picture and a file name); the grey-olive mount in the maker's line-up of three (9c70063ca49b) is it by its look. FLAT DARK EARTH is a copper-bronze in every photograph of this mount (Primary Arms' 56a035336ff3, Rifle Supply's 4dd72ffb8646, the maker's line-up and on-rifle view), redder and darker than the AUS mount's flat dark earth on file (reptilia-fde): fitted to these photographs as reptilia-dot-fde. The maker's 100-037 and 100-038 pictures are one picture recoloured and aren't used for colour. Black is the matte black of the photographs, not fitted (a black on hard anodize). Piece map, black and FDE alike (Primary Arms' 100-037_00 and 100-038_00, Rifle Supply's views): the deck, the stem and the base are the body's anodize; the steel clamp, the cross bolt's head and its end are black steel (the hardware slot)."},"hardware":{"label":"Steel clamp and cross bolt","finish":"nitride","recolorable":false,"color":"steel-nitride-black","note":"The spring-loaded clamp on the right face and the cross bolt (its slotted head in its seat on the left face, its end in the clamp): black steel on the black and the flat dark earth mounts alike, drawn as black nitride by the maker's words. Reptilia: \"Nitrided 4140 steel\", \"spring-loaded nitrided steel clamp and mounting bolt\"."}},"components":{"body":{"label":"Mount","material":"body"},"hardware":{"label":"Steel clamp and cross bolt","material":"hardware"}},"geometry":{"model":"reptilia-dot-mount-193.glb","components":{},"approximations":["Its heights and the base's length are read on the maker's square view of it with a CompM5 on a receiver, at the rail's pitch; its outline on Rifle Supply's square view of the black one alone, at that length. Nothing else in either view is a published size: each reading is good to a hundredth or two of an inch (the ledger gives each its ±).","Its width (31.5 mm) and the I-beam's width across its flanges (14 mm) are the lower 1/3's, as one reader measured that mount (Soldier Systems, 2019): no view or page gives this height's. The two heights' side views read the same base, deck plate and flanges.","The deck plate is drawn flat at its floor, where a dot's base stands: the two lips along its long edges (lip_height, assumed 0.03 in) and the raised key in its middle aren't drawn, since a Micro dot drawn on file is a box as wide as the deck and would stand in them. From the side the plate is lip_height lower than the photographs have its top.","The stem is the outline at the flanges' width across, each face pocketed down to the web between two flanges flange_thickness wide that run along the outline's two sides: the I-beam. The web's thickness (0.1 in) is assumed, inside what the maker's two weights leave for it; no view is square on to the mount's end.","The base is the outline from its foot to its ends' top, the mount's width, its two lower outer edges (the jaws' feet) chamfered 0.05 in (assumed, from the view from below) and its other edges square; its channel is the rail's own head in section (MIL-STD-1913's) down to the lower gauge line, and from there straight down to the foot as far apart as the head's lower faces end (.748): Primary Arms' view of the 1.93's front end (932ddb83c5e0) has the channel's sides straight, and how far a jaw hooks in under the head isn't read. The two bars across the channel either side of the clamp aren't drawn (which slots they stand in isn't read), nor the oval pockets in the channel's roof that its four holes open into; the four holes are drawn through, 0.12 in across (assumed).","The steel clamp is drawn as the slab of it that stands proud of the right face, over the base's chamfer, its ends and top chamfered, with the bolt's end in it; its size is assumed from the views from the right. The bolt's head is flush in a shallow round seat, a slot across it at 45 degrees; its shank and the clamp's spring aren't drawn. The four holes for the dot's screws are drawn through the deck plate (sizes and places assumed); the screws aren't. Engraving and the logo aren't drawn; every edge is broken 0.006 in.","As drawn it is 1.24 cubic inches of 7075 and 0.009 of steel: 58.7 g for the maker's 55 (7% over). The steel clamp and the bolt inside the base, and the channel's pockets, aren't drawn; the width and the web the weight rests on are a reader's and an assumption (gaps)."],"ledger":["reptilia-dot-mount-193.deck_above_rail","reptilia-dot-mount-193.lip_top_above_rail","reptilia-dot-mount-193.mount_length","reptilia-dot-mount-193.clamp_below_rail","reptilia-dot-mount-193.width","reptilia-dot-mount-193.stem_width","reptilia-dot-mount-193.web_thickness"]},"profiles":{"side":{"plane":"xy","origin":"on the lips' top (the outline's top) over the middle of the base's length, where the cross bolt is","offset":{"y":"lip_top_above_rail"},"points":[[-1.02,-1.401],[-1.02,-1.554],[-1.016,-1.599],[-1.005,-1.62],[-0.196,-1.627],[-0.024,-1.633],[0.196,-1.627],[1.002,-1.627],[1.016,-1.615],[1.02,-1.596],[1.02,-1.346],[1.013,-1.265],[0.989,-1.237],[0.67,-1.091],[0.586,-1.045],[0.539,-0.995],[0.516,-0.933],[0.513,-0.44],[0.529,-0.378],[0.552,-0.346],[0.576,-0.325],[0.846,-0.156],[0.875,-0.143],[0.93,-0.14],[0.946,-0.133],[0.987,-0.021],[0.987,-0.011],[0.976,-0.003],[0.771,0],[0.002,0],[-0.969,0],[-0.981,-0.008],[-0.981,-0.028],[-0.943,-0.13],[-0.882,-0.136],[-0.826,-0.159],[-0.576,-0.315],[-0.523,-0.372],[-0.507,-0.424],[-0.507,-0.914],[-0.513,-0.95],[-0.529,-0.989],[-0.583,-1.045],[-0.982,-1.234],[-1.013,-1.265]],"scaleRefs":["reptilia-dot-mount-193.mount_length"],"inputs":{"reptilia-dot-mount-193.mount_length":2.039},"tolerance":0.004,"photo":"references/reptilia-dot-mount-193 e9d8dbdb0275 (Rifle Supply 125332.png: the black DOT mount 1.93 alone, square from the left, transparent ground, 1280 x 853)","method":"luminance < 240, closing ×3, largest piece, holes filled; scale from reptilia-dot-mount-193.mount_length = 2.039 in (x-extent 628 px → 308.0 px/in); origin at x center, y max of the outline; Douglas-Peucker at 0.004 in with the extremes kept: 45 points (IoU 0.996 with the full outline) (tools/trace.py)","via":"harvest","note":"The mount's left side, turned to face +x: the deck plate (the lips' top is the outline's top), its underside running down into the I-beam's flanges, the waist, the flare into the base, the base's square ends and its bottom. The model takes the deck plate, the stem and the base from it at three widths."}},"gaps":[{"what":"A view square on to the mount's end, or its width from a page","need":"The width, the flanges' width and the web's thickness rest on one reader's figures for the lower 1/3 and the maker's two weights; a front or rear view of either height would read them"},{"what":"Which dot the maker's 1.93 in is given for","need":"A sentence naming it: the page names none; its photographs show a CompM5, which isn't on file, and on them the CompM5's axis stands 0.05 in under where a T-2's would (deck_above_rail's two measurements)"},{"what":"The deck's lips' height, and the two bars across the channel","need":"A view square on to the deck's end, and one from below square on to the channel (which slots the bars stand in)"},{"what":"A number for the Clear Anodized mount","need":"The maker's page lists the colour with no number; it is sold only by LiveQordie.com, which no harvested page reads"},{"what":"Where the maker means it to go on a rifle","need":"Its page says only \"attaches to any M1913 Picatinny rail\"; its on-rifle photographs have it on the receiver's rail"}]},"reptilia-dot-mount-39mm":{"id":"reptilia-dot-mount-39mm","name":"DOT MOUNT FOR AIMPOINT® MICRO – LOWER 1/3 (39MM HEIGHT)","manufacturer":"Reptilia","sku":"100-004","url":"https://reptiliacorp.com/product/dot-mount-for-aimpoint-micro/","category":"optic_mount","description":"Reptilia's one-piece red dot mount for the Aimpoint Micro footprint: \"Machined from billet 7075-T6 aluminum with Milspec Type III hard anodized finish, the DOT Mount attaches to any M1913 Picatinny rail, and offers lower 1/3 co-witness with standard AR15-style back-up sights. Its spring-loaded nitrided steel clamp and mounting bolt simplify the installation process\". 51 grams; NSN 1005-01-674-6542. Every photograph on its page has a Micro T-2 on it. On the maker's own photograph of a carbine with it and a T-2, read at the rail's pitch, the deck stands higher than \"39MM\" as a T-2's axis would put it (deck_above_rail).","weight":"reptilia-dot-mount-39mm.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":[0,0,0],"note":"Mount frame: origin on the rail's top under the middle of the base's length, +x forward. The cross bolt's head is there in every left view (its seat's middle within 0.02 in of the base's), 0.02 in over the rail's top by the outline's foot (bolt_above_foot less clamp_below_rail)."},"deck":{"origin":["{.deck_x}","{.deck_above_rail}",0],"note":"On the deck's floor between its lips, at the footprint's middle: where a Micro dot's base is put (D101). The lips stand lip_height over it at the deck's long edges."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":"={.mount_length} / 2","clamp_front":"={.mount_length} / 2"},"flips":false,"note":"The base's length about its middle, where its one cross bolt is. The maker says only that it \"attaches to any M1913 Picatinny rail\": nothing it publishes says where along a rail, or of the receiver's rail against the handguard's."},"deck":{"type":"optic_footprint","role":"deck","anchor":"deck","params":{"pattern":"aimpoint_micro"},"flips":false,"note":"Cut for the Aimpoint Micro: the maker's title (\"DOT MOUNT FOR AIMPOINT® MICRO\") and \"Compatible with: Aimpoint® – Micro R-1, H-1, H-2, T-1, T-2, CompM5\"; MidwayUSA sells it as \"Reptilia DOT Aimpoint T-1, T-2 Lower 1/3 Co-Witness Red Dot Mount\" (data/interfaces.yaml, optic_footprint)."}},"materials":{"body":{"label":"Mount","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized_matte","color":"placeholder-black","sku":"100-004","source":"https://reptiliacorp.com/product/dot-mount-for-aimpoint-micro/"},"fde":{"label":"Flat Dark Earth Anodized","finish":"anodized_matte","color":"reptilia-dot-fde","sku":"100-024","source":"https://reptiliacorp.com/product/dot-mount-for-aimpoint-micro/"}},"default":"black","note":"Reptilia: \"Machined from billet 7075-T6 aluminum with Milspec Type III hard anodized finish\", \"Type III hardcoat anodized 7075 aluminum\". The page sells it in Clear Anodize, Flat Dark Earth Anodized and Black, and prints \"BLACK: 100-004 FDE: 100-024\"; Clear has no number: \"Clear anodized DOT Mounts sold exclusively by Q at LiveQordie.com\". CLEAR is sold and NOT OFFERED: no page on file gives it a number; the grey-olive mount in the maker's line-up of three (b2bfa2eeb1af, and Soldier Systems' launch photograph 7de4d8d522fc) is it by its look. FLAT DARK EARTH is a copper-bronze in every photograph of this mount (Primary Arms' 64c81bc1e76b, the maker's line-up and its views on rifles): drawn in the DOT mounts' own flat dark earth, reptilia-dot-fde, fitted to these parts' photographs. Black is the matte black of the photographs, not fitted (a black on hard anodize). Piece map, black and FDE alike (Primary Arms' R100-024_00, the maker's DOT-MOUNT-03 and -07, Rifle Supply's 125330_A): the deck, the stem and the base are the body's anodize; the steel clamp, the cross bolt's head and its end are black steel (the hardware slot)."},"hardware":{"label":"Steel clamp and cross bolt","finish":"nitride","recolorable":false,"color":"steel-nitride-black","note":"The spring-loaded clamp on the right face and the cross bolt (its slotted head in its seat on the left face, its end in the clamp): black steel on the black and the flat dark earth mounts alike, drawn as black nitride by the maker's words. Reptilia: \"Nitrided 4140 steel\", \"spring-loaded nitrided steel clamp and mounting bolt\"."}},"components":{"body":{"label":"Mount","material":"body"},"hardware":{"label":"Steel clamp and cross bolt","material":"hardware"}},"geometry":{"model":"reptilia-dot-mount-39mm.glb","components":{},"approximations":["Its scale is the base's length as one reader measured it (Soldier Systems, 2019: 52.2 mm), which the maker's square view of a whole carbine with it reads within its pixel at the rail's pitch; that view is small (the mount 57 px long), and the lips' height over the rail is read on it to 0.03 in. Its outline is Rifle Supply's square view of the black one alone, yawed a degree or two: its front end's outline is the end face's far edge, about 0.03 in ahead of the near one.","Its width (31.5 mm) and the I-beam's width across its flanges (14 mm) are the reader's figures, taken as across the rifle; no view is square on to the mount's end.","The deck plate is drawn flat at its floor, where a dot's base stands: the two lips along its long edges (lip_height, assumed 0.03 in) and the raised key in its middle aren't drawn, since a Micro dot drawn on file is a box as wide as the deck and would stand in them. From the side the plate is lip_height lower than the photographs have its top.","The stem is the outline at the flanges' width across, each face pocketed down to the web between two flanges flange_thickness wide that run along the outline's two sides: the I-beam. The web's thickness (0.1 in) is assumed, inside what the maker's two weights leave for it.","The base is the outline from its foot to its ends' top, the mount's width, its two lower outer edges (the jaws' feet) chamfered 0.05 in (assumed, from the view from below) and its other edges square; its channel is the rail's own head in section (MIL-STD-1913's) down to the lower gauge line, and from there straight down to the foot as far apart as the head's lower faces end (.748): Primary Arms' view of the 1.93's front end (932ddb83c5e0) has the channel's sides straight, and how far a jaw hooks in under the head isn't read. The two bars across the channel either side of the clamp aren't drawn (which slots they stand in isn't read), nor the oval pockets in the channel's roof that its four holes open into; the four holes are drawn through, 0.12 in across (assumed).","The steel clamp is drawn as the slab of it that stands proud of the right face, over the base's chamfer, its ends and top chamfered, with the bolt's end in it; its size is assumed from the views from the right. The bolt's head is flush in a shallow round seat, a slot across it at 45 degrees; its shank and the clamp's spring aren't drawn. The four holes for the dot's screws are drawn through the deck plate (sizes and places assumed); the screws aren't. Engraving and the logo aren't drawn; every edge is broken 0.006 in.","As drawn it is 1.19 cubic inches of 7075 and 0.009 of steel: 56.1 g for the maker's 51 (10% over). The steel clamp and the bolt inside the base, and the channel's pockets, aren't drawn; the width and the web the weight rests on are a reader's and an assumption (gaps)."],"ledger":["reptilia-dot-mount-39mm.deck_above_rail","reptilia-dot-mount-39mm.lip_top_above_rail","reptilia-dot-mount-39mm.mount_length","reptilia-dot-mount-39mm.clamp_below_rail","reptilia-dot-mount-39mm.width","reptilia-dot-mount-39mm.stem_width","reptilia-dot-mount-39mm.web_thickness"]},"profiles":{"side":{"plane":"xy","origin":"on the lips' top (the outline's top) over the middle of the base's length, where the cross bolt is","offset":{"y":"lip_top_above_rail"},"points":[[-1.028,-1.047],[-1.025,-1.195],[-1.016,-1.276],[-1.008,-1.29],[0.713,-1.305],[1.028,-1.303],[1.028,-0.93],[0.634,-0.741],[0.606,-0.716],[0.579,-0.677],[0.56,-0.616],[0.56,-0.454],[0.57,-0.414],[0.594,-0.372],[0.643,-0.331],[0.887,-0.181],[0.984,-0.175],[1.003,-0.161],[1.012,-0.137],[1.006,-0.131],[1.006,-0.038],[1.016,-0.017],[1.005,-0.006],[0.99,-0.003],[0.866,0],[0.002,0],[-0.957,0],[-0.964,-0.005],[-0.922,-0.131],[-0.912,-0.142],[-0.86,-0.157],[-0.833,-0.157],[-0.791,-0.172],[-0.547,-0.325],[-0.494,-0.369],[-0.473,-0.405],[-0.464,-0.441],[-0.464,-0.604],[-0.47,-0.64],[-0.488,-0.683],[-0.532,-0.729],[-0.559,-0.747],[-0.893,-0.901],[-1.005,-0.925],[-1.016,-0.948]],"scaleRefs":["reptilia-dot-mount-39mm.mount_length"],"inputs":{"reptilia-dot-mount-39mm.mount_length":2.0551181102362204},"tolerance":0.004,"photo":"references/reptilia-dot-mount-39mm 25b8fb31a520 (Rifle Supply 125330.png: the black DOT mount, lower 1/3 (39 mm), alone, square from the left, transparent ground, 1280 x 853)","method":"luminance < 240, 2 boxes excluded, closing ×3, largest piece, holes filled; scale from reptilia-dot-mount-39mm.mount_length = 2.05512 in (x-extent 682 px → 331.9 px/in); origin at x center, y max of the outline; Douglas-Peucker at 0.004 in with the extremes kept: 45 points (IoU 0.996 with the full outline) (tools/trace.py)","via":"harvest","note":"The mount's left side, turned to face +x: the deck plate (the lips' top is the outline's top), its underside running down into the I-beam's flanges, the waist, the flare into the base, the base's square ends and its bottom. The model takes the deck plate, the stem and the base from it at three widths."}},"gaps":[{"what":"What the maker's \"39MM HEIGHT\" is measured to, and for which dot","need":"A sentence or a drawing: read as a T-2's axis over the rail's top (as Aimpoint names its own 39 mm spacer) it puts the deck 0.12 in under where the maker's own photograph of this mount on a carbine has it (deck_above_rail, a conflict kept)"},{"what":"A view square on to the mount's end, or its width from a page","need":"The width, the flanges' width and the web's thickness rest on one reader's figures and the maker's two weights; a front or rear view would read them"},{"what":"A larger photograph of it on a rail, square from the side","need":"The heights rest on a whole-carbine photograph at 28 px an inch; the maker's other views of it on rifles are three-quarter views"},{"what":"The deck's lips' height, and the two bars across the channel","need":"A view square on to the deck's end, and one from below square on to the channel (which slots the bars stand in)"},{"what":"A number for the Clear Anodize mount","need":"The maker's page lists the colour with no number; it is sold only by LiveQordie.com, which no harvested page reads"}]},"rise-lpk":{"id":"rise-lpk","name":"Lower parts kit, less trigger","manufacturer":"Rise Armament","category":"lpk","weight":"rise-lpk.weight","occupies":[],"integral":[],"brings":["selector"],"seats":{},"requires":[],"anchors":{"lpk":{"origin":[0,0,0],"note":"On the receiver's left face, level with the takedown pin: the controls stand out from it toward −Z."}},"interfaces":{"lpk":{"type":"ar15.lpk","role":"kit","anchor":"lpk","params":{},"flips":false}},"materials":{"controls":{"label":"Controls","finish":"phosphate","recolorable":false,"color":"placeholder-black","note":"8620 steel, black phosphate (Rise: \"Many of the parts in the RISE Lower Parts Kit feature a black phosphate finish.\", https://risearmament.com/product/ar-15-lower-parts-kit/). One retailer says manganese phosphate. Sold in the one finish (12003). On Rise's photo of the kit laid out (396370c75a0e) the magazine catch and its button, the bolt catch, the selector, the two receiver pins, the buffer retainer and the bolt catch's plunger are one black, a matte charcoal black on the cast pieces and a little glossier on the turned pins: a black, not fitted to a photo. What isn't drawn: the three detents (\"made of yellow zinc\", Rise: gold in the photo), the springs (bare steel wire, the detents' a yellow), the bolt catch's roll pin (dark steel): all inside the receiver."}},"components":{"controls":{"label":"Bolt catch, magazine release, pins","material":"controls"},"selector":{"label":"Selector","material":"controls"}},"geometry":{"components":{"selector":"rise-lpk.selector.glb"},"approximations":[],"ledger":["rise-lpk.takedown_pin_head_d","rise-lpk.pivot_pin_head_d","rise-lpk.pivot_pin_head_flat","rise-lpk.selector_hub_d","rise-lpk.selector_lever_t","rise-lpk.bolt_catch_paddle_rear_x","rise-lpk.bolt_catch_t","rise-lpk.magazine_release_w","rise-lpk.magazine_release_standoff","std.ar15.mag_catch_x","std.ar15.mag_catch_y","std.ar15.selector_x","std.ar15.selector_y","std.ar15.hammer_pin_x","std.ar15.hammer_pin_y","std.ar15.trigger_pin_x","std.ar15.trigger_pin_y","std.ar15.takedown_hole_d","std.ar15.pivot_hole_d","std.ar15.selector_hole_d","std.ar15.fcg_pin_hole_d"]},"profiles":{},"gaps":[]},"rosco-bloodline-105-barrel":{"id":"rosco-bloodline-105-barrel","name":"Bloodline 10.5\" M4 5.56 NATO","manufacturer":"Rosco Manufacturing","sku":"BL-105-M4-556-7-C","url":"https://www.roscomanufacturing.com/shop/barrels/blood-line-barrels/5-56-barrels/bloodline-10-5-m4-5-56-nato/","category":"barrel","description":"Rosco's 10.5 in Bloodline barrel: 4150 chrome moly vanadium steel, a 5.56 NATO chamber, 1/7 twist, nitrided inside and out with its M4 extension, a carbine-length gas port on a .750 in journal with one dimple under it, a 1/2 x 28 muzzle thread behind an 11 degree crown.","weight":"rosco-bloodline-105-barrel.weight","barrelLength":"rosco-bloodline-105-barrel.length","cartridge":{"takes":["5.56 NATO"],"stated":"Bloodline 10.5″ M4 5.56 NATO","source":"https://www.roscomanufacturing.com/shop/barrels/blood-line-barrels/5-56-barrels/bloodline-10-5-m4-5-56-nato/ (the page's heading, as cached: harvest.quote; its list has \"Barrel Caliber 5.56\", and the barrel is marked ROSCO 5.56 NATO 1/7 4150 CMV; the seller Primary Arms has \"Chambered in 5.56 NATO, 1:7 twist\" for the same number)"},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"extension":{"origin":[0,0,0],"note":"The barrel extension's flange, its rear face, on the bore axis, +x toward the muzzle."},"muzzle":{"origin":["{.shoulder_x}",0,0]},"gas_journal":{"origin":["{.gas_port_x}",0,0]}},"interfaces":{"barrel_extension":{"type":"ar15.barrel_extension","role":"barrel","anchor":"extension","params":{},"flips":false,"note":"Primary Arms, for this number: \"nitride-finished M4 barrel extension\" and \"Feed Ramps M4\"; Rosco's list: \"Barrel Extension Finish Nitride\"."},"muzzle":{"type":"muzzle_thread","role":"barrel","anchor":"muzzle","params":{"thread":"1/2-28","thread_length":"={.thread_length}"},"flips":false,"note":"Rosco: \"Barrel Thread 1/2 x 28\" and \"Barrel Crown 11 Degree\"; its FAQ: \"5.56 are threaded to ½ X 28\". Its length is read off the photo."},"gas_journal":{"type":"ar15.gas_journal","role":"barrel","anchor":"gas_journal","params":{"journal_od":"={.journal_od}"},"flips":false,"note":"Rosco: \"Gas Block Size .750\"; its FAQ: \"We currently machine the “journal” or seating area to accommodate a .750 diameter gas block for all our barrels.\" and, of the dimple under it, \"we only machine one dimple that is perfectly centered and matched to a backspace of .295\"."},"gas_system":{"type":"ar15.gas_system","role":"barrel","params":{"length":"carbine"},"flips":false,"note":"Rosco's list for this barrel: \"Gas System Length Carbine\" (https://www.roscomanufacturing.com/shop/barrels/blood-line-barrels/5-56-barrels/bloodline-10-5-m4-5-56-nato/); Primary Arms: \"carbine-length gas system\". What the platform checks a gas tube against a barrel by (D83)."}},"materials":{"barrel":{"label":"Barrel","finish":"nitride","recolorable":false,"color":"steel-nitride-black","note":"Rosco's list: \"Barrel Finish Nitride\" and \"Barrel Extension Finish Nitride\"; its FAQ calls it \"a Melonite finish\"; Primary Arms: \"Salt bath nitride finish, nitride-finished M4 barrel extension\"; MidwayUSA's colour: \"Black Nitride\". The one finish this number is sold in. One slot: in Primary Arms' photos of this barrel the extension, its index pin, the collar, the journal and the thread are the barrel's own black; the dimple under the journal is bare steel and isn't drawn. Not fitted to a photo: a nitrided black is the finish's own look (data/colors/steel.yaml)."}},"components":{},"geometry":{"model":"rosco-bloodline-105-barrel.glb","components":{},"approximations":["Turned from its side outline, traced from Primary Arms' photo of this barrel, extension to muzzle, read column by column at the scale the barrel's own straight section gives there (a yawed photo reads wider at one end), that section's diameter (0.662) read against the journal's published .750; its length is set to the published one (10.5 in from its breech end, with the extension's half inch behind that: 11.00). At the photo's own scale its two end faces read 10.97 in apart.","Every face is squared where the ledger has it: the photo sees each from off square and rounds its corner by its rim's arc, so the flange's two faces, the collar's front face (where a gas block stops), the journal's front end and the muzzle shoulder are each read behind that arc. The shoulder's corner is drawn sharp.","Ahead of the collar the barrel is drawn from figures, not from the outline: the journal at its published .750 for the 1.95 in the photo gives it, a cone a tenth of an inch long down to the section ahead of it, that section at the 0.729 the photo reads, to the shoulder.","The indexing pin at the reference CAD set's .125, where the 11.5 in Bloodline's photo has it on the same extension (this barrel's own photo has it turned out of sight); the gas port a hole of the .073 a buyer gives for the 11.5 in barrel's (Rosco withholds each barrel's), on top of the journal .295 ahead of the collar's front face, where Rosco's FAQ puts the dimple opposite it; the bore one plain hole right through, at the Army drawing's .219; the extension's rear opening turned at the reference CAD set's sizes (its chamfered mouth, the ring its locking lugs make, the recess ahead of them).","The muzzle thread is a helix, 28 to the inch, between the minor and major diameters of the Army barrel's 1/2-28 thread (Rosco states 1/2 x 28): a plain V without the flats of its form, right-hand (assumed: its designation marks no other), running out at the shoulder over its last pitch, with no relief there or chamfer at the muzzle.","The crown is a plain cone at Rosco's 11 degrees, from the thread's root in to the bore: how far across the muzzle's face it reaches isn't published (Rosco's close-up of its 12.5 in sibling's muzzle has the crown from a narrow rim at the thread's edge in to the bore, as drawn here).","Not drawn: the dimple under the journal opposite the port (its diameter and depth aren't sourced), the chamber, the slots between the extension's locking lugs and its M4 feed ramps (the lugs are one ring), the marking on top (ROSCO 5.56 NATO 1/7 4150 CMV and the maker's dog)."],"ledger":["rosco-bloodline-105-barrel.overall_length","rosco-bloodline-105-barrel.extension_rear_x","rosco-bloodline-105-barrel.flange_front_x","rosco-bloodline-105-barrel.shoulder_x","rosco-bloodline-105-barrel.gas_port_x","rosco-bloodline-105-barrel.journal_od","rosco-bloodline-105-barrel.muzzle_od"]},"profiles":{"side":{"plane":"xy","origin":"the silhouette's rear tip, on the axis; the outline begins at the extension's rear face","offset":{"x":"extension_rear_x"},"points":[[0.077,0.484],[0.078,-0.497],[1.017,-0.498],[1.03,-0.545],[1.06,-0.586],[1.184,-0.586],[1.193,-0.578],[1.198,-0.55],[1.209,-0.54],[1.222,-0.493],[1.884,-0.488],[1.912,-0.477],[1.939,-0.477],[2.026,-0.455],[2.113,-0.445],[2.118,-0.439],[2.146,-0.439],[2.173,-0.428],[2.2,-0.428],[2.26,-0.412],[2.315,-0.406],[2.32,-0.401],[2.347,-0.401],[2.435,-0.379],[2.456,-0.379],[2.462,-0.374],[2.489,-0.374],[2.522,-0.363],[2.549,-0.363],[2.555,-0.357],[2.637,-0.346],[2.642,-0.341],[2.697,-0.335],[2.702,-0.33],[6.902,-0.332],[6.907,-0.338],[6.986,-0.338],[6.992,-0.343],[7.092,-0.349],[7.098,-0.354],[7.12,-0.354],[7.193,-0.377],[7.21,-0.377],[7.306,-0.41],[7.356,-0.416],[7.362,-0.421],[7.396,-0.422],[7.401,-0.427],[7.975,-0.422],[7.981,-0.428],[8.006,-0.408],[8.02,-0.377],[8.066,-0.377],[8.071,-0.372],[9.909,-0.373],[9.915,-0.367],[9.972,-0.367],[9.977,-0.362],[10.486,-0.362],[10.523,-0.331],[10.535,-0.314],[10.56,-0.244],[10.824,-0.239],[10.83,-0.244],[10.933,-0.244],[10.938,-0.239],[10.984,-0.239],[10.99,-0.244],[11.078,-0.244],[11.078,0.246],[10.956,0.246],[10.95,0.251],[10.933,0.246],[10.921,0.251],[10.904,0.251],[10.898,0.246],[10.887,0.251],[10.87,0.251],[10.864,0.246],[10.852,0.251],[10.835,0.251],[10.83,0.246],[10.818,0.251],[10.795,0.251],[10.789,0.246],[10.778,0.251],[10.761,0.246],[10.703,0.246],[10.698,0.251],[10.692,0.246],[10.675,0.251],[10.658,0.251],[10.652,0.246],[10.64,0.251],[10.623,0.245],[10.572,0.245],[10.557,0.254],[10.54,0.304],[10.517,0.344],[10.503,0.358],[10.492,0.358],[10.474,0.369],[9.943,0.368],[9.937,0.374],[9.852,0.374],[9.846,0.379],[8.02,0.377],[8.006,0.407],[7.987,0.427],[7.351,0.426],[7.266,0.392],[7.25,0.392],[7.199,0.375],[7.177,0.375],[7.149,0.364],[7.126,0.364],[7.076,0.347],[7.014,0.342],[7.008,0.336],[6.924,0.336],[6.919,0.33],[6.913,0.336],[6.896,0.33],[6.807,0.33],[6.801,0.336],[6.784,0.336],[6.779,0.33],[6.728,0.33],[6.723,0.336],[6.717,0.33],[4.924,0.328],[4.919,0.333],[4.897,0.333],[4.891,0.328],[4.841,0.327],[4.836,0.333],[4.819,0.333],[4.814,0.327],[4.803,0.333],[2.915,0.33],[2.91,0.325],[2.762,0.325],[2.757,0.33],[2.691,0.33],[2.686,0.335],[2.62,0.341],[2.615,0.346],[2.593,0.346],[2.533,0.363],[2.506,0.363],[2.5,0.368],[2.478,0.368],[2.369,0.395],[2.309,0.401],[2.282,0.412],[2.222,0.417],[2.135,0.439],[2.042,0.45],[2.015,0.461],[1.988,0.461],[1.933,0.477],[1.868,0.482],[1.863,0.488],[1.797,0.488],[1.792,0.493],[1.651,0.493],[1.645,0.487],[1.64,0.493],[1.613,0.493],[1.607,0.487],[1.244,0.487],[1.214,0.495],[1.209,0.539],[1.179,0.574],[1.141,0.585],[1.087,0.585],[1.082,0.579],[1.076,0.585],[1.06,0.579],[1.025,0.505],[1.011,0.492],[0.984,0.492],[0.979,0.486],[0.827,0.491],[0.822,0.497],[0.509,0.496],[0.503,0.491],[0.094,0.495]],"scaleRefs":["rosco-bloodline-105-barrel.barrel_od","rosco-bloodline-105-barrel.overall_length"],"inputs":{"rosco-bloodline-105-barrel.barrel_od":0.662,"rosco-bloodline-105-barrel.outline_front_face":11.078,"rosco-bloodline-105-barrel.outline_rear_face":0.077,"rosco-bloodline-105-barrel.overall_length":11.001},"tolerance":0.004,"photo":"references/rosco-bloodline-105-barrel 4b61a27db095 (Primary Arms' gallery, BL-105-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","method":"luminance < 235, largest piece, holes filled; scale from rosco-bloodline-105-barrel.barrel_od = 0.662 in, the tube's own width column by column: 119.3 px over columns 879–1189, 120.1 px over columns 1249–1559; a line through them (rms 0.13 px) changes +1.1% from column 879 to 1559, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 180.4 px/in there. The axis is the tube's centre line (tilt -0.02°, rms 0.04 px). Lengths then scaled by 1.0024 so that the end faces are rosco-bloodline-105-barrel.overall_length = 11.001 in apart: at the tube's scale they read 10.975 (-0.2%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.090 in over radius 0.244 (rms 0.002), the rear end's rim sags 0.068 in over radius 0.491 (rms 0.012); origin at x min of the outline, on the tube's axis; clipped to x min {.outline_rear_face} = 0.077, x max {.outline_front_face} = 11.078; Douglas-Peucker at 0.004 in with the extremes kept: 188 points (IoU 0.999 with the full outline); checks: height (tooth tops, max over 0.05 in windows) along x [0.2, 0.8] 0.994 ± 0.018; height (tooth tops, max over 0.05 in windows) along x [3.2, 6.2] 0.662 ± 0.017 in vs rosco-bloodline-105-barrel.barrel_od 0.662 ± 0.004 (provisional): agrees; height (tooth tops, max over 0.05 in windows) along x [8.3, 9.3] 0.750 ± 0.017 in vs rosco-bloodline-105-barrel.journal_od 0.75 ± 0.0005 (confirmed): agrees; centre between the top (max over 0.4 in windows) along x [3.2, 6.2] 0.000 ± 0.017 (tools/trace.py)","via":"harvest","note":"Black on white, the silhouette at 235 of 255, mirrored (the photo has the muzzle at the left), cut at its two end faces. Each column is scaled by the straight section's own width there; lengths are set by the published length between the end faces. Each shoulder's corner is rounded by its rim's arc (the lens sees every face from off square): the model squares those faces where the ledger has them."}},"gaps":[{"what":"Where the 10.5 in is measured from","need":"Rosco's statement (taken from the barrel's breech end, as the Army's drawing dimensions a barrel; from the bolt's face it would be an eighth shorter overall)"},{"what":"The profile's diameters and lengths: Rosco publishes none but the journal's .750 and the dimple's .295","need":"A maker's drawing; or a straight side photo with a scale in the barrel's plane"},{"what":"The dimple under the journal: its diameter and depth","need":"Rosco's figure, or a side photo with the dimple on the silhouette"},{"what":"The gas port's diameter","need":"Rosco's figure (its FAQ withholds it; the one figure on file is a buyer's for the 11.5 in barrel)"},{"what":"The crown: how far across the muzzle's face its cone reaches","need":"A view of the muzzle from its end, with the thread's diameter in it as the scale"},{"what":"The extension's locking lugs and feed ramps, and the chamber's mouth","need":"The extension's drawing (8448550 isn't in the package): its inside is the reference CAD set's, turned; hidden once the barrel is in a receiver"},{"what":"The index pin's place on this barrel","need":"A side photo of this length with the pin on the silhouette (it is the 11.5 in barrel's reading on the same extension)"}]},"rosco-bloodline-115-barrel":{"id":"rosco-bloodline-115-barrel","name":"Bloodline 11.5\" M4 5.56 NATO","manufacturer":"Rosco Manufacturing","sku":"BL-115-M4-556-7-C","url":"https://www.roscomanufacturing.com/shop/barrels/blood-line-barrels/5-56-barrels/bloodline-11-5-m4-5-56-nato/","category":"barrel","description":"Rosco's 11.5 in Bloodline barrel: 4150 chrome moly vanadium steel, a 5.56 NATO chamber, 1/7 twist, nitrided inside and out with its M4 extension, a carbine-length gas port on a .750 in journal with one dimple under it, a 1/2 x 28 muzzle thread behind an 11 degree crown.","weight":"rosco-bloodline-115-barrel.weight","barrelLength":"rosco-bloodline-115-barrel.length","cartridge":{"takes":["5.56 NATO"],"stated":"Bloodline 11.5″ M4 5.56 NATO","source":"https://www.roscomanufacturing.com/shop/barrels/blood-line-barrels/5-56-barrels/bloodline-11-5-m4-5-56-nato/ (the page's heading, as cached: harvest.quote; its list has \"Barrel Caliber 5.56\", and the barrel is marked ROSCO 5.56 NATO 1/7 4150 CMV; the seller Primary Arms has \"Chambered in 5.56 NATO, 1:7 twist\" for the same number)"},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"extension":{"origin":[0,0,0],"note":"The barrel extension's flange, its rear face, on the bore axis, +x toward the muzzle."},"muzzle":{"origin":["{.shoulder_x}",0,0]},"gas_journal":{"origin":["{.gas_port_x}",0,0]}},"interfaces":{"barrel_extension":{"type":"ar15.barrel_extension","role":"barrel","anchor":"extension","params":{},"flips":false,"note":"Primary Arms, for this number: \"nitride-finished M4 barrel extension\" and \"Feed Ramps M4\"; Rosco's list: \"Barrel Extension Finish Nitride\"."},"muzzle":{"type":"muzzle_thread","role":"barrel","anchor":"muzzle","params":{"thread":"1/2-28","thread_length":"={.thread_length}"},"flips":false,"note":"Rosco: \"Barrel Thread 1/2 x 28\" and \"Barrel Crown 11 Degree\"; its FAQ: \"5.56 are threaded to ½ X 28\". Its length is read off the photo."},"gas_journal":{"type":"ar15.gas_journal","role":"barrel","anchor":"gas_journal","params":{"journal_od":"={.journal_od}"},"flips":false,"note":"Rosco: \"Gas Block Size .750\"; its FAQ: \"We currently machine the “journal” or seating area to accommodate a .750 diameter gas block for all our barrels.\" and, of the dimple under it, \"we only machine one dimple that is perfectly centered and matched to a backspace of .295\"."},"gas_system":{"type":"ar15.gas_system","role":"barrel","params":{"length":"carbine"},"flips":false,"note":"Rosco's list for this barrel: \"Gas System Length Carbine\" (https://www.roscomanufacturing.com/shop/barrels/blood-line-barrels/5-56-barrels/bloodline-11-5-m4-5-56-nato/); Primary Arms: \"carbine-length gas system\". What the platform checks a gas tube against a barrel by (D83)."}},"materials":{"barrel":{"label":"Barrel","finish":"nitride","recolorable":false,"color":"steel-nitride-black","note":"Rosco's list: \"Barrel Finish Nitride\" and \"Barrel Extension Finish Nitride\"; its FAQ calls it \"a Melonite finish\"; Primary Arms: \"Salt bath nitride finish, nitride-finished M4 barrel extension\"; MidwayUSA's colour: \"Black Nitride\". The one finish this number is sold in. One slot: in Primary Arms' photos of this barrel the extension, its index pin, the collar, the journal and the thread are the barrel's own black; the dimple under the journal is bare steel and isn't drawn. Not fitted to a photo: a nitrided black is the finish's own look (data/colors/steel.yaml)."}},"components":{},"geometry":{"model":"rosco-bloodline-115-barrel.glb","components":{},"approximations":["Turned from its side outline, traced from Primary Arms' photo of this barrel, extension to muzzle, read column by column at the scale the barrel's own straight section gives there (a yawed photo reads wider at one end), that section's diameter (0.665) read against the journal's published .750; its length is set to the published one (11.5 in from its breech end, with the extension's half inch behind that: 12.00). At the photo's own scale its two end faces read 11.91 in apart.","Every face is squared where the ledger has it: the photo sees each from off square and rounds its corner by its rim's arc, so the flange's two faces, the collar's front face (where a gas block stops), the journal's front end and the muzzle shoulder are each read behind that arc. The shoulder's corner is drawn sharp.","Ahead of the collar the barrel is drawn from figures, not from the outline: the journal at its published .750 for the 1.97 in the photo gives it, a cone a tenth of an inch long down to the section ahead of it, that section at the 0.724 the photo reads, to the shoulder.","The indexing pin at the reference CAD set's .125, where and as high as the photo has it; the gas port at a buyer's .073 (Rosco withholds its size), on top of the journal .295 ahead of the collar's front face, where Rosco's FAQ puts the dimple opposite it; the bore one plain hole right through, at the Army drawing's .219; the extension's rear opening turned at the reference CAD set's sizes (its chamfered mouth, the ring its locking lugs make, the recess ahead of them).","The muzzle thread is a helix, 28 to the inch, between the minor and major diameters of the Army barrel's 1/2-28 thread (Rosco states 1/2 x 28): a plain V without the flats of its form, right-hand (assumed: its designation marks no other), running out at the shoulder over its last pitch, with no relief there or chamfer at the muzzle.","The crown is a plain cone at Rosco's 11 degrees, from the thread's root in to the bore: how far across the muzzle's face it reaches isn't published (Rosco's close-up of its 12.5 in sibling's muzzle has the crown from a narrow rim at the thread's edge in to the bore, as drawn here).","Not drawn: the dimple under the journal opposite the port (its diameter and depth aren't sourced), the chamber, the slots between the extension's locking lugs and its M4 feed ramps (the lugs are one ring), the marking on top (ROSCO 5.56 NATO 1/7 4150 CMV and the maker's dog)."],"ledger":["rosco-bloodline-115-barrel.overall_length","rosco-bloodline-115-barrel.extension_rear_x","rosco-bloodline-115-barrel.flange_front_x","rosco-bloodline-115-barrel.shoulder_x","rosco-bloodline-115-barrel.gas_port_x","rosco-bloodline-115-barrel.journal_od","rosco-bloodline-115-barrel.muzzle_od"]},"profiles":{"side":{"plane":"xy","origin":"the silhouette's rear tip, on the axis; the outline begins at the extension's rear face","offset":{"x":"extension_rear_x"},"points":[[0.114,0.498],[0.114,-0.493],[0.516,-0.494],[0.521,-0.5],[0.702,-0.5],[0.708,-0.494],[0.936,-0.495],[0.942,-0.501],[1.036,-0.501],[1.042,-0.578],[1.077,-0.578],[1.083,-0.584],[1.188,-0.584],[1.212,-0.572],[1.232,-0.552],[1.253,-0.49],[1.888,-0.491],[1.894,-0.485],[1.924,-0.485],[1.959,-0.473],[1.988,-0.473],[2.024,-0.461],[2.048,-0.461],[2.053,-0.456],[2.077,-0.456],[2.083,-0.45],[2.112,-0.45],[2.148,-0.438],[2.172,-0.438],[2.177,-0.432],[2.207,-0.432],[2.242,-0.42],[2.266,-0.42],[2.272,-0.414],[2.296,-0.414],[2.302,-0.408],[2.325,-0.408],[2.331,-0.403],[2.355,-0.403],[2.361,-0.397],[2.384,-0.397],[2.39,-0.391],[2.455,-0.385],[2.491,-0.373],[2.515,-0.373],[2.521,-0.367],[2.55,-0.367],[2.556,-0.361],[2.586,-0.361],[2.615,-0.349],[2.645,-0.349],[2.651,-0.344],[2.681,-0.344],[2.716,-0.332],[4.399,-0.334],[4.411,-0.328],[4.417,-0.334],[4.784,-0.335],[4.79,-0.329],[5.073,-0.329],[5.079,-0.335],[5.17,-0.335],[5.176,-0.329],[5.702,-0.33],[5.708,-0.336],[5.939,-0.336],[5.945,-0.33],[6.334,-0.331],[6.34,-0.337],[6.383,-0.337],[6.389,-0.331],[6.48,-0.331],[6.486,-0.337],[6.578,-0.337],[6.584,-0.331],[6.871,-0.331],[6.877,-0.325],[6.895,-0.325],[6.902,-0.331],[7.018,-0.332],[7.024,-0.338],[7.067,-0.338],[7.103,-0.35],[7.128,-0.35],[7.134,-0.356],[7.165,-0.356],[7.195,-0.368],[7.244,-0.374],[7.342,-0.411],[7.361,-0.411],[7.398,-0.429],[7.557,-0.423],[7.563,-0.429],[7.662,-0.429],[7.668,-0.423],[7.754,-0.424],[7.76,-0.43],[8.037,-0.43],[8.065,-0.409],[8.087,-0.376],[8.105,-0.369],[8.124,-0.37],[8.13,-0.376],[9.238,-0.377],[9.251,-0.371],[9.257,-0.377],[9.437,-0.378],[9.444,-0.371],[9.487,-0.372],[9.493,-0.378],[9.612,-0.378],[9.618,-0.372],[10.018,-0.372],[10.024,-0.366],[10.068,-0.366],[10.074,-0.36],[10.324,-0.361],[10.331,-0.367],[10.356,-0.367],[10.362,-0.361],[11.539,-0.362],[11.574,-0.341],[11.627,-0.246],[12.115,-0.246],[12.115,0.241],[12.071,0.24],[12.064,0.247],[11.659,0.24],[11.653,0.246],[11.627,0.246],[11.605,0.28],[11.599,0.305],[11.552,0.357],[11.4,0.357],[11.394,0.363],[10.08,0.361],[10.074,0.368],[10.018,0.367],[10.011,0.374],[9.593,0.373],[9.587,0.379],[9.574,0.373],[9.344,0.373],[9.338,0.379],[9.319,0.373],[8.698,0.372],[8.692,0.378],[8.321,0.378],[8.315,0.384],[8.309,0.378],[8.253,0.378],[8.247,0.372],[8.148,0.371],[8.142,0.377],[8.087,0.377],[8.043,0.426],[7.41,0.431],[7.275,0.382],[7.201,0.37],[7.195,0.364],[7.171,0.364],[7.14,0.352],[7.116,0.352],[7.085,0.34],[7.048,0.34],[7.042,0.334],[6.761,0.334],[6.755,0.327],[6.737,0.333],[6.486,0.333],[6.48,0.327],[6.474,0.333],[6.243,0.333],[6.237,0.327],[6.194,0.327],[6.188,0.333],[5.672,0.332],[5.666,0.326],[5.406,0.332],[5.4,0.326],[5.321,0.326],[5.315,0.332],[3.752,0.33],[3.746,0.336],[3.686,0.336],[3.68,0.33],[3.257,0.33],[3.251,0.336],[3.162,0.336],[3.156,0.33],[3.019,0.33],[3.013,0.336],[2.716,0.329],[2.71,0.335],[2.686,0.335],[2.651,0.347],[2.621,0.347],[2.615,0.353],[2.592,0.353],[2.586,0.359],[2.562,0.359],[2.526,0.371],[2.497,0.371],[2.491,0.377],[2.414,0.389],[2.408,0.394],[2.378,0.394],[2.343,0.406],[2.248,0.418],[2.219,0.43],[2.189,0.43],[2.16,0.442],[2.059,0.453],[2.053,0.459],[2.03,0.459],[2.024,0.465],[2,0.465],[1.994,0.471],[1.971,0.471],[1.935,0.483],[1.906,0.483],[1.9,0.489],[1.753,0.489],[1.747,0.495],[1.6,0.494],[1.594,0.488],[1.459,0.488],[1.453,0.494],[1.423,0.494],[1.417,0.488],[1.253,0.488],[1.244,0.497],[1.244,0.52],[1.227,0.562],[1.2,0.582],[1.118,0.582],[1.112,0.588],[1.106,0.582],[1.077,0.582],[1.065,0.576],[1.039,0.538],[1.033,0.508],[1.013,0.493],[0.942,0.493],[0.936,0.499]],"scaleRefs":["rosco-bloodline-115-barrel.barrel_od","rosco-bloodline-115-barrel.overall_length"],"inputs":{"rosco-bloodline-115-barrel.barrel_od":0.665,"rosco-bloodline-115-barrel.outline_front_face":12.115,"rosco-bloodline-115-barrel.outline_rear_face":0.114,"rosco-bloodline-115-barrel.overall_length":12.001},"tolerance":0.004,"photo":"references/rosco-bloodline-115-barrel 4aaee849158f (Primary Arms' gallery, BL-115-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","method":"luminance < 235, 1 boxes excluded, largest piece, holes filled; scale from rosco-bloodline-115-barrel.barrel_od = 0.665 in, the tube's own width column by column: 110.2 px over columns 949–1139, 111.2 px over columns 1199–1629; a line through them (rms 0.25 px) changes +1.5% from column 949 to 1629, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 165.9 px/in there. The axis is the tube's centre line (tilt +0.01°, rms 0.13 px). Lengths then scaled by 1.0078 so that the end faces are rosco-bloodline-115-barrel.overall_length = 12.001 in apart: at the tube's scale they read 11.908 (-0.8%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.104 in over radius 0.240 (rms 0.002), the rear end's rim sags 0.112 in over radius 0.494 (rms 0.002); origin at x min of the outline, on the tube's axis; clipped to x min {.outline_rear_face} = 0.114, x max {.outline_front_face} = 12.115; Douglas-Peucker at 0.004 in with the extremes kept: 245 points (IoU 0.999 with the full outline); The index pin (columns 1927 to 1941 of the lower edge, behind the flange) is boxed out: it is a pin, not a ring.; checks: height (tooth tops, max over 0.05 in windows) along x [0.2, 0.8] 0.992 ± 0.019; height (tooth tops, max over 0.05 in windows) along x [3.2, 6.2] 0.664 ± 0.019 in vs rosco-bloodline-115-barrel.barrel_od 0.665 ± 0.004 (provisional): agrees; height (tooth tops, max over 0.05 in windows) along x [8.3, 9.7] 0.750 ± 0.019 in vs rosco-bloodline-115-barrel.journal_od 0.75 ± 0.0005 (confirmed): agrees; height (tooth tops, max over 0.05 in windows) along x [11.55, 11.9] 0.486 ± 0.018; centre between the top (max over 0.4 in windows) along x [3.2, 6.2] -0.000 ± 0.018 (tools/trace.py)","via":"harvest","note":"Black on white, the silhouette at 235 of 255, mirrored (the photo has the muzzle at the left), cut at its two end faces. The photo is yawed, so each column is scaled by the straight section's own width there; lengths are set by the published length between the end faces. Each shoulder's corner is rounded by its rim's arc (the lens sees the flange from 12° off square, the collar's front face from 13°, the muzzle shoulder from 22°): the model squares those faces where the ledger has them."}},"gaps":[{"what":"Where the 11.5 in is measured from","need":"Rosco's statement (taken from the barrel's breech end, as the Army's drawing dimensions a barrel; from the bolt's face it would be an eighth shorter overall)"},{"what":"The profile's diameters and lengths: Rosco publishes none but the journal's .750 and the dimple's .295","need":"A maker's drawing; or a straight side photo with a scale in the barrel's plane"},{"what":"The dimple under the journal: its diameter and depth","need":"Rosco's figure, or a side photo with the dimple on the silhouette"},{"what":"The gas port's diameter","need":"Rosco's figure (its FAQ withholds it; .073 is a buyer's, no instrument named)"},{"what":"The crown: how far across the muzzle's face its cone reaches","need":"A view of the muzzle from its end, with the thread's diameter in it as the scale"},{"what":"The extension's locking lugs and feed ramps, and the chamber's mouth","need":"The extension's drawing (8448550 isn't in the package): its inside is the reference CAD set's, turned; hidden once the barrel is in a receiver"}]},"rosco-bloodline-125-barrel":{"id":"rosco-bloodline-125-barrel","name":"Bloodline 12.5\" M4 5.56 NATO","manufacturer":"Rosco Manufacturing","sku":"BL-125-M4-556-7-C","url":"https://www.roscomanufacturing.com/shop/barrels/blood-line-barrels/5-56-barrels/bloodline-12-5-5-56-nato/","category":"barrel","description":"Rosco's 12.5 in Bloodline barrel: 4150 chrome moly vanadium steel, a 5.56 NATO chamber, 1/7 twist, nitrided inside and out with its M4 extension, a carbine-length gas port on a .750 in journal with one dimple under it, a 1/2 x 28 muzzle thread behind an 11 degree crown.","weight":"rosco-bloodline-125-barrel.weight","barrelLength":"rosco-bloodline-125-barrel.length","cartridge":{"takes":["5.56 NATO"],"stated":"Bloodline 12.5” M4 5.56 NATO","source":"https://www.roscomanufacturing.com/shop/barrels/blood-line-barrels/5-56-barrels/bloodline-12-5-5-56-nato/ (the page's heading, as cached: harvest.quote; its list has \"Barrel Caliber 5.56\", and the barrel is marked ROSCO 5.56 NATO 1/7 4150 CMV; the seller Primary Arms has \"Chambered in 5.56 NATO, 1:7 twist\" for the same number)"},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"extension":{"origin":[0,0,0],"note":"The barrel extension's flange, its rear face, on the bore axis, +x toward the muzzle."},"muzzle":{"origin":["{.shoulder_x}",0,0]},"gas_journal":{"origin":["{.gas_port_x}",0,0]}},"interfaces":{"barrel_extension":{"type":"ar15.barrel_extension","role":"barrel","anchor":"extension","params":{},"flips":false,"note":"Primary Arms, for this number: \"nitride-finished M4 barrel extension\" and \"Feed Ramps M4\"; Rosco's list: \"Barrel Extension Finish Nitride\"."},"muzzle":{"type":"muzzle_thread","role":"barrel","anchor":"muzzle","params":{"thread":"1/2-28","thread_length":"={.thread_length}"},"flips":false,"note":"Rosco: \"Barrel Thread 1/2 x 28\" and \"Barrel Crown 11 Degree\"; its FAQ: \"5.56 are threaded to ½ X 28\". Its length is read off the photo."},"gas_journal":{"type":"ar15.gas_journal","role":"barrel","anchor":"gas_journal","params":{"journal_od":"={.journal_od}"},"flips":false,"note":"Rosco: \"Gas Block Size .750\"; its FAQ: \"We currently machine the “journal” or seating area to accommodate a .750 diameter gas block for all our barrels.\" and, of the dimple under it, \"we only machine one dimple that is perfectly centered and matched to a backspace of .295\"."},"gas_system":{"type":"ar15.gas_system","role":"barrel","params":{"length":"carbine"},"flips":false,"note":"Rosco's list for this barrel: \"Gas System Length Carbine Length\" (https://www.roscomanufacturing.com/shop/barrels/blood-line-barrels/5-56-barrels/bloodline-12-5-5-56-nato/); Primary Arms: \"carbine-length gas system\". What the platform checks a gas tube against a barrel by (D83)."}},"materials":{"barrel":{"label":"Barrel","finish":"nitride","recolorable":false,"color":"steel-nitride-black","note":"Rosco's list: \"Barrel Finish Nitride\" and \"Barrel Extension Finish Nitride\"; its FAQ calls it \"a Melonite finish\"; Primary Arms: \"Salt bath nitride finish, nitride-finished M4 barrel extension\"; MidwayUSA's colour: \"Black Nitride\". The one finish this number is sold in. One slot: in Primary Arms' photos of this barrel the extension, its index pin, the collar, the journal and the thread are the barrel's own black; the dimple under the journal is bare steel and isn't drawn. Not fitted to a photo: a nitrided black is the finish's own look (data/colors/steel.yaml)."}},"components":{},"geometry":{"model":"rosco-bloodline-125-barrel.glb","components":{},"approximations":["Turned from its side outline, traced from Primary Arms' photo of this barrel, extension to muzzle, read column by column at the scale the barrel's own straight section gives there (a yawed photo reads wider at one end), that section's diameter (0.666) read against the journal's published .750; its length is set to the published one (12.5 in from its breech end, with the extension's half inch behind that: 13.00). At the photo's own scale its two end faces read 13.00 in apart.","Every face is squared where the ledger has it: the photo sees each from off square and rounds its corner by its rim's arc, so the flange's two faces, the collar's front face (where a gas block stops), the journal's front end and the muzzle shoulder are each read behind that arc. The shoulder's corner is drawn sharp.","Ahead of the collar the barrel is drawn from figures, not from the outline: the journal at its published .750 for the 2.00 in the photo gives it, a cone a tenth of an inch long down to the section ahead of it, that section at the 0.720 the photo reads, to the shoulder.","The photo reads this barrel's breech end 1% large (its extension 1.010 where the Army's drawing allows .999): the outline's radii behind the middle of the straight section are brought down in proportion to how far back they are, to the drawing's figure at the extension.","The indexing pin at the reference CAD set's .125, where and as high as the photo has it; the gas port a hole of the .073 a buyer gives for the 11.5 in barrel's (Rosco withholds each barrel's), on top of the journal .295 ahead of the collar's front face, where Rosco's FAQ puts the dimple opposite it; the bore one plain hole right through, at the Army drawing's .219; the extension's rear opening turned at the reference CAD set's sizes (its chamfered mouth, the ring its locking lugs make, the recess ahead of them).","The muzzle thread is a helix, 28 to the inch, between the minor and major diameters of the Army barrel's 1/2-28 thread (Rosco states 1/2 x 28): a plain V without the flats of its form, right-hand (assumed: its designation marks no other), running out at the shoulder over its last pitch, with no relief there or chamfer at the muzzle.","The crown is a plain cone at Rosco's 11 degrees, from the thread's root in to the bore: how far across the muzzle's face it reaches isn't published (Rosco's close-up of this barrel's muzzle, DSC00420, has it from a narrow rim at the thread's edge in to the bore, as drawn).","Not drawn: the dimple under the journal opposite the port (its diameter and depth aren't sourced), the chamber, the slots between the extension's locking lugs and its M4 feed ramps (the lugs are one ring), the marking on top (ROSCO 5.56 NATO 1/7 4150 CMV and the maker's dog)."],"ledger":["rosco-bloodline-125-barrel.overall_length","rosco-bloodline-125-barrel.extension_rear_x","rosco-bloodline-125-barrel.flange_front_x","rosco-bloodline-125-barrel.shoulder_x","rosco-bloodline-125-barrel.gas_port_x","rosco-bloodline-125-barrel.journal_od","rosco-bloodline-125-barrel.muzzle_od"]},"profiles":{"side":{"plane":"xy","origin":"the silhouette's rear tip, on the axis; the outline begins at the extension's rear face","offset":{"x":"extension_rear_x"},"points":[[0.103,0.503],[0.103,-0.496],[0.108,-0.501],[0.917,-0.501],[0.923,-0.508],[0.949,-0.508],[0.956,-0.514],[1.055,-0.514],[1.058,-0.583],[1.107,-0.586],[1.114,-0.593],[1.212,-0.593],[1.238,-0.58],[1.268,-0.544],[1.275,-0.511],[1.291,-0.488],[1.298,-0.494],[1.941,-0.494],[1.948,-0.488],[1.981,-0.488],[1.987,-0.481],[2.013,-0.481],[2.02,-0.474],[2.053,-0.474],[2.086,-0.461],[2.118,-0.461],[2.125,-0.455],[2.151,-0.455],[2.158,-0.448],[2.184,-0.448],[2.191,-0.442],[2.217,-0.442],[2.223,-0.435],[2.25,-0.435],[2.256,-0.428],[2.289,-0.428],[2.296,-0.422],[2.322,-0.422],[2.329,-0.415],[2.361,-0.415],[2.368,-0.409],[2.394,-0.409],[2.401,-0.402],[2.427,-0.402],[2.434,-0.396],[2.46,-0.396],[2.466,-0.389],[2.493,-0.389],[2.499,-0.382],[2.525,-0.382],[2.532,-0.376],[2.565,-0.376],[2.571,-0.369],[2.598,-0.369],[2.604,-0.363],[2.637,-0.363],[2.67,-0.35],[2.696,-0.35],[2.703,-0.343],[2.729,-0.343],[2.735,-0.336],[2.768,-0.336],[2.775,-0.33],[3.739,-0.33],[3.746,-0.336],[3.851,-0.336],[3.857,-0.329],[3.864,-0.336],[3.871,-0.329],[3.877,-0.336],[3.884,-0.329],[3.89,-0.336],[3.897,-0.329],[3.903,-0.336],[3.91,-0.329],[3.917,-0.336],[3.923,-0.329],[3.93,-0.336],[3.936,-0.329],[3.943,-0.336],[3.949,-0.329],[4.054,-0.329],[4.061,-0.336],[4.526,-0.336],[4.533,-0.329],[4.579,-0.329],[4.585,-0.336],[6.571,-0.335],[6.578,-0.329],[6.938,-0.328],[6.945,-0.335],[7.056,-0.335],[7.063,-0.342],[7.095,-0.342],[7.102,-0.348],[7.148,-0.348],[7.154,-0.355],[7.194,-0.355],[7.2,-0.361],[7.259,-0.368],[7.37,-0.407],[7.41,-0.413],[7.449,-0.433],[8.071,-0.433],[8.11,-0.38],[8.13,-0.38],[8.136,-0.374],[8.3,-0.374],[8.307,-0.38],[9.981,-0.38],[9.988,-0.373],[10.289,-0.373],[10.295,-0.367],[10.916,-0.366],[10.923,-0.373],[10.969,-0.373],[10.975,-0.366],[12.484,-0.366],[12.491,-0.372],[12.497,-0.366],[12.524,-0.366],[12.537,-0.359],[12.56,-0.336],[12.573,-0.31],[12.579,-0.278],[12.595,-0.248],[12.609,-0.248],[12.615,-0.255],[12.628,-0.248],[12.641,-0.248],[12.648,-0.255],[12.661,-0.248],[12.68,-0.248],[12.687,-0.255],[12.7,-0.248],[12.713,-0.248],[12.72,-0.255],[12.733,-0.248],[12.746,-0.248],[12.752,-0.255],[12.765,-0.248],[12.778,-0.248],[12.785,-0.255],[12.798,-0.248],[12.817,-0.248],[12.824,-0.255],[12.831,-0.248],[12.85,-0.248],[12.857,-0.255],[12.863,-0.248],[12.883,-0.248],[12.889,-0.255],[12.902,-0.255],[12.909,-0.248],[12.922,-0.248],[12.928,-0.255],[12.935,-0.248],[12.955,-0.248],[12.961,-0.255],[12.968,-0.248],[12.981,-0.248],[12.987,-0.255],[13,-0.255],[13.007,-0.248],[13.013,-0.254],[13.104,-0.248],[13.104,0.217],[13.098,0.223],[13.085,0.23],[13.059,0.23],[13.053,0.236],[13.033,0.236],[13.026,0.23],[13.02,0.236],[12.798,0.236],[12.791,0.23],[12.785,0.236],[12.772,0.236],[12.765,0.23],[12.752,0.23],[12.739,0.236],[12.733,0.23],[12.72,0.23],[12.713,0.236],[12.706,0.23],[12.654,0.23],[12.648,0.236],[12.602,0.236],[12.586,0.252],[12.579,0.285],[12.553,0.331],[12.53,0.347],[12.504,0.347],[12.497,0.354],[12.452,0.347],[12.445,0.354],[10.086,0.36],[10.079,0.367],[9.667,0.366],[9.661,0.373],[8.516,0.373],[8.509,0.366],[8.464,0.366],[8.457,0.373],[8.149,0.373],[8.143,0.379],[8.136,0.373],[8.13,0.379],[8.11,0.379],[8.077,0.425],[7.442,0.425],[7.298,0.373],[7.279,0.373],[7.272,0.366],[7.239,0.366],[7.233,0.36],[7.207,0.36],[7.2,0.353],[7.174,0.353],[7.167,0.346],[7.102,0.34],[7.095,0.333],[6.997,0.333],[6.991,0.327],[6.945,0.327],[6.938,0.333],[2.768,0.333],[2.762,0.339],[2.729,0.339],[2.722,0.346],[2.696,0.346],[2.69,0.352],[2.663,0.352],[2.657,0.359],[2.63,0.359],[2.624,0.365],[2.591,0.365],[2.585,0.372],[2.558,0.372],[2.552,0.378],[2.525,0.378],[2.519,0.385],[2.493,0.385],[2.486,0.392],[2.46,0.392],[2.453,0.398],[2.42,0.398],[2.414,0.405],[2.355,0.411],[2.348,0.418],[2.315,0.418],[2.309,0.424],[2.283,0.424],[2.276,0.431],[2.25,0.431],[2.243,0.437],[2.171,0.444],[2.138,0.457],[2.072,0.464],[2.04,0.477],[2.007,0.477],[2,0.483],[1.974,0.483],[1.967,0.49],[1.941,0.49],[1.935,0.496],[1.587,0.496],[1.58,0.49],[1.383,0.49],[1.376,0.496],[1.311,0.496],[1.288,0.506],[1.268,0.552],[1.232,0.595],[1.12,0.595],[1.114,0.588],[1.101,0.588],[1.084,0.578],[1.051,0.519],[1.035,0.503],[0.949,0.503],[0.943,0.509],[0.122,0.509]],"scaleRefs":["rosco-bloodline-125-barrel.barrel_od","rosco-bloodline-125-barrel.overall_length"],"inputs":{"rosco-bloodline-125-barrel.barrel_od":0.666,"rosco-bloodline-125-barrel.outline_front_face":13.104,"rosco-bloodline-125-barrel.outline_rear_face":0.103,"rosco-bloodline-125-barrel.overall_length":13.001},"tolerance":0.004,"photo":"references/rosco-bloodline-125-barrel 0f416d824f87 (Primary Arms' gallery, BL-125-M4-556-7-C_02: the barrel from the side on white, the muzzle at the left, 2200 x 1467)","method":"luminance < 235, 1 boxes excluded, largest piece, holes filled; scale from rosco-bloodline-125-barrel.barrel_od = 0.666 in, the tube's own width column by column: 101.7 px over columns 1069–1339, 101.5 px over columns 1399–1653; a line through them (rms 0.16 px) changes -0.1% from column 1069 to 1653, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 152.6 px/in there. The axis is the tube's centre line (tilt -0.01°, rms 0.07 px). Lengths then scaled by 0.9997 so that the end faces are rosco-bloodline-125-barrel.overall_length = 13.001 in apart: at the tube's scale they read 13.005 (+0.0%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.077 in over radius 0.236 (rms 0.002), the rear end's rim sags 0.103 in over radius 0.501 (rms 0.003); origin at x min of the outline, on the tube's axis; clipped to x min {.outline_rear_face} = 0.103, x max {.outline_front_face} = 13.104; Douglas-Peucker at 0.004 in with the extremes kept: 283 points (IoU 0.998 with the full outline); The index pin (on the lower edge behind the flange) is boxed out: it is a pin, not a ring.; checks: height (tooth tops, max over 0.05 in windows) along x [0.2, 0.8] 1.011 ± 0.021; height (tooth tops, max over 0.05 in windows) along x [3.2, 6.2] 0.668 ± 0.020 in vs rosco-bloodline-125-barrel.barrel_od 0.666 ± 0.004 (provisional): agrees; height (tooth tops, max over 0.05 in windows) along x [8.3, 9.3] 0.753 ± 0.020 in vs rosco-bloodline-125-barrel.journal_od 0.75 ± 0.0005 (confirmed): agrees; centre between the top (max over 0.4 in windows) along x [3.2, 6.2] -0.001 ± 0.020 (tools/trace.py)","via":"harvest","note":"Black on white, the silhouette at 235 of 255, mirrored (the photo has the muzzle at the left), cut at its two end faces. Each column is scaled by the straight section's own width there; lengths are set by the published length between the end faces. Each shoulder's corner is rounded by its rim's arc (the lens sees every face from off square): the model squares those faces where the ledger has them."}},"gaps":[{"what":"Where the 12.5 in is measured from","need":"Rosco's statement (taken from the barrel's breech end, as the Army's drawing dimensions a barrel; from the bolt's face it would be an eighth shorter overall)"},{"what":"The profile's diameters and lengths: Rosco publishes none but the journal's .750 and the dimple's .295","need":"A maker's drawing; or a straight side photo with a scale in the barrel's plane"},{"what":"The dimple under the journal: its diameter and depth","need":"Rosco's figure, or a side photo with the dimple on the silhouette"},{"what":"The gas port's diameter","need":"Rosco's figure (its FAQ withholds it; the one figure on file is a buyer's for the 11.5 in barrel)"},{"what":"The crown: how far across the muzzle's face its cone reaches","need":"A view of the muzzle from its end, with the thread's diameter in it as the scale"},{"what":"The extension's locking lugs and feed ramps, and the chamber's mouth","need":"The extension's drawing (8448550 isn't in the package): its inside is the reference CAD set's, turned; hidden once the barrel is in a receiver"},{"what":"This photo's scale at the breech end: it reads the extension 1% over the Army's limit and 0.03 longer behind the flange than the standard's, with a straight section whose width shows no yaw","need":"A second straight side photo of this length (Rosco's own of it are three-quarter views), or the maker's drawing"},{"what":"The weight against the model: its volume as steel is 6% over Rosco's 21.79 oz, where its siblings' are 1 and 2% over theirs","need":"Rosco's confirmation of the 12.5's weight, or a weighing"}]},"sb-tactical-sba3":{"id":"sb-tactical-sba3","name":"SBA3® AR Adjustable Pistol Stabilizing Brace®","manufacturer":"SB Tactical","sku":"SBA3X-01-SB","url":"https://www.sb-tactical.com/product/sba3/","category":"brace","description":"SB Tactical's slim five-position brace for an AR pistol: a polymer housing round a mil-spec carbine tube with a lever that draws its lock pin, a block under it with an ambidextrous QD socket, an end cap behind, and under the cap a cuff of two fins round a window, with a one-inch nylon strap through a loop on top and round the cuff. 6.75 oz by the maker's page. Its shape is read from the maker's straight left and rear views, and its size and place from the maker's two pictures of it on a pistol, framed by the lower's pins; no drawing or design patent of it is on file.","weight":"sb-tactical-sba3.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"butt":{"origin":[0,0,0],"note":"The end cap's rear face on the tube axis: the brace's rearmost plane and the part frame's origin. The overall length ends here, as it does at a stock's butt (ATF's handbook, 2.1.4: \"the rearmost portion of the weapon\")."},"tube":{"origin":["{.butt_behind_pin_pos1}",0,0],"x":[-1,0,0],"note":"Brace frame: origin on the tube axis in the plane of its rear, +x forward. At its first position (collapsed) this anchor sits at the takedown pin's X. The maker: \"5-position adjustable\"; on a six-hole carbine tube its five positions are the tube's steps from the front hole (the two pictures put its rear 2.68 in apart, collapsed and extended: four steps of 0.66 and the published 9.5 less 6.75 either side)."}},"interfaces":{"tube":{"type":"receiver_extension","role":"stock","anchor":"tube","params":{"profile":"mil-spec","positions":5},"flips":false,"note":"Five positions in the maker's words: its sheet's \"Designed for all platforms capable of accepting a mil-spec carbine extension, the SBA3® 5-position adjustable brace\" and its page's \"5-position adjustable configuration\" (on a six-hole tube the fewer, five, bound it). SB Tactical's page: \"compatibility with mil-spec carbine receiver extensions\" and \"The SBA3 is designed for platforms that accept a mil-spec carbine receiver extension\"; its sheet: \"Does not include mil-spec carbine receiver extension\"; its instructions (SBA3, SBA4, SBA5, SBA6): \"compatible with mil-spec carbine receiver extensions (not included)\" and \"If your lower receiver assembly has a pistol buffer tube installed, remove the pistol buffer tube.\""}},"materials":{"body":{"label":"Brace body","finish":"polymer","recolorable":true,"color":"placeholder-polymer-black","sheen":"satin","options":{"black":{"label":"Black","finish":"polymer","color":"placeholder-polymer-black","sheen":"satin","sku":"SBA3X-01-SB","source":"https://www.sb-tactical.com/product/sba3/"},"fde":{"label":"FDE","finish":"polymer","color":"sb-tactical-sba3-fde","sheen":"satin","sku":"SBA3X-02-SB","source":"https://www.sb-tactical.com/product/sba3/"},"odg":{"label":"OD Green","finish":"polymer","color":"sb-tactical-sba3-odg","sheen":"satin","sku":"SBA3X-04-SB","source":"https://www.sb-tactical.com/product/sba3/"}},"default":"black","note":"The maker's page: \"Reinforced polymer construction\" and \"Available in Black, FDE, OD Green\" (SKU SBA3X-01-SB, -02-SB, -04-SB). The housing, the lever, the block, the end cap, the loop and the cuff are the one colour in each (the maker's three pictures, SBA3-black-, -fde- and -green-product_image.jpg). Primary Arms' table says \"Material Rubber\"; the maker says polymer. Sold too and not offered: Stealth Gray (SBA3X-03M-SB, on the 2021 sheet and at Impact Guns; not on the maker's page today, and no picture of it on file)."},"strap":{"label":"Strap","finish":"polymer","recolorable":false,"color":"placeholder-polymer-black","sheen":"matte","note":"The sheet: \"Comes with adjustable nylon strap for custom fit\", \"Strap Width: 1\"\"; black on the black, FDE and OD green braces alike (the maker's three pictures, and Midwest Gun Works' of the black and the FDE together). Drawn as matte polymer: the catalog has no fabric finish."},"hardware":{"label":"Pins and QD socket cup","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"The lever's cross pin, the block's pin and the QD socket's cup round its bore: bright, silver steel in all three colourways' pictures. No page names the steel or its finish: drawn as bright stainless by its look."}},"components":{"body":{"label":"Housing, lever, block, end cap and cuff","material":"body"},"strap":{"label":"Strap","material":"strap"},"hardware":{"label":"Pins and QD socket cup","material":"hardware"}},"geometry":{"model":"sb-tactical-sba3.glb","components":{},"approximations":["Built inside the maker's straight left-side outline (mirrored to face +x; scaled by the length and height read on its two pictures on a pistol, which fit it within 1.1%) and the maker's straight view from the rear (scaled by the height). No view shows the top, the underside or the front, and no drawing or patent is on file.","The housing's section is the end cap's in the rear view (a flat top, wide chamfers to the axis's height, upright sides), carried forward to the housing's front: the oblique from behind shows the same chamfers along the housing's top. The housing is as wide as the end cap's block, the maker's sheet's 1.8 in maximum; whether it narrows toward its front isn't shown.","Under the ledge along its side the housing's lower part, the lever's block and the QD block are set in by an assumed 0.12 in each side (lower_inset): only the oblique shows that the ledge is there. The lever is a plate each side as thick as an assumed 0.08 in, standing out of the lower part, and solid across where it hangs below it (the real one is a fork round the lock pin, whose spring and pin aren't drawn).","The end cap's plate is set in from the block's sides by 0.08 in (the rear view's second outline; the side view's step under the block's top agrees, and is the outline's), as deep as the side outline shows it; its chamfers are drawn as the block's, and the maker's mark on it isn't drawn.","The cuff's section is the rear view's inside its strap, carried fore and aft from the side outline's front edge to its rear; the window through it is the rear view's, the split under it a slot as wide as the picture's. The bar across the cuff that the strap passes under stands proud of the strap by the strap's thickness.","The bore is a mil-spec tube's section with its rail (std.receiver_extension) and an assumed 0.01 in clearance, from the front face as deep as the tube's rear end reaches at the collapsed seat (6.22 in; the sheet's \"Cavity Depth: 6\"\" is stated to the inch). The lock pin and its spring inside aren't drawn.","The strap is a band of the published 1 in width as thick as the rear view's 0.12 in, round the end cap's block and the cuff on the side picture's band, under the loop's bridge on top and under the cuff's split; its loose end and its buckle aren't drawn.","The steel is drawn plain: each pin a head 0.1 in across standing a hair proud each side; the QD socket a cup of its rim's 0.55 in round its 0.4 in bore, each side (the maker: \"Integral, ambidextrous QD sling socket\"). The two notches under the ledge and the groove along the lower part are cut an assumed 0.03 in deep, the QD block's two recessed panels an assumed 0.1 in (the rib down the upper one isn't drawn).","It is drawn solid where it is moulded: the end cap's block, the cuff above its window and the block under the lever are solid in the model (18.9 cubic inches with its strap), and the published 6.75 oz is about half a reinforced polymer of that volume (0.66 to 0.81 oz to the cubic inch, taken on trust: no page gives the resin's). No view shows its inside; what is cored isn't drawn, and the build's weight is the page's.","Not drawn: the maker's mark on the end cap, the logo and lettering, the strap's hook-and-loop texture."],"ledger":["sb-tactical-sba3.length","sb-tactical-sba3.height","sb-tactical-sba3.width","sb-tactical-sba3.tube_axis_below_top","sb-tactical-sba3.butt_behind_pin_pos1","sb-tactical-sba3.cavity_depth","sb-tactical-sba3.strap_width","sb-tactical-sba3.strap_thickness","sb-tactical-sba3.qd_bore_diameter","sb-tactical-sba3.qd_cup_diameter","sb-tactical-sba3.pin_head_diameter","sb-tactical-sba3.lower_inset","sb-tactical-sba3.lever_thickness","sb-tactical-sba3.relief_depth","sb-tactical-sba3.pocket_depth","sb-tactical-sba3.endcap_inset","sb-tactical-sba3.bore_clearance"]},"profiles":{"side":{"plane":"xy","origin":"the end cap's rear face (x, after the mirror) and the strap loop's top (y); the housing's top is level in the picture, so the tube's axis is horizontal","offset":{"y":"tube_axis_below_top"},"points":[[0,-0.403],[0,-1.815],[0.017,-1.865],[0.042,-1.89],[0.075,-1.896],[0.117,-1.943],[0.1,-1.971],[0.1,-2.01],[0.111,-2.043],[0.117,-2.165],[0.128,-2.204],[0.156,-2.632],[0.178,-2.816],[0.239,-4.15],[0.256,-4.79],[0.25,-4.862],[0.261,-4.995],[0.261,-5.646],[0.267,-5.679],[0.295,-5.712],[0.356,-5.751],[0.356,-5.779],[0.403,-5.793],[1.443,-5.793],[1.468,-5.785],[1.479,-5.74],[1.543,-5.699],[1.562,-5.662],[1.562,-5.401],[1.59,-5.123],[1.59,-5.04],[1.757,-3.65],[1.857,-2.627],[1.876,-2.602],[1.993,-2.602],[2.09,-2.699],[2.088,-2.719],[2.099,-2.707],[2.282,-2.885],[2.327,-2.913],[3.405,-2.908],[3.477,-2.891],[3.555,-2.852],[3.614,-2.799],[3.647,-2.755],[3.675,-2.694],[3.669,-2.371],[3.683,-2.357],[5.195,-2.318],[5.29,-2.313],[5.362,-2.296],[5.479,-2.179],[5.496,-2.19],[5.509,-2.177],[5.498,-2.16],[5.621,-2.032],[5.632,-1.91],[5.651,-1.885],[5.996,-1.885],[6.032,-1.865],[6.054,-1.799],[6.049,-1.448],[6.06,-1.348],[6.343,-1.065],[6.338,-0.72],[6.31,-0.47],[6.305,-0.325],[6.293,-0.275],[6.274,-0.267],[5.646,-0.278],[1.743,-0.261],[1.465,0],[0.192,0],[0.156,-0.019],[0.145,-0.053],[0.133,-0.259],[0.058,-0.345],[0.025,-0.35],[0.011,-0.364]],"features":{"through":[[[2.607,-2.493],[2.607,-2.416],[2.58,-2.349],[2.505,-2.279],[2.443,-2.263],[2.377,-2.263],[2.31,-2.291],[2.274,-2.332],[2.246,-2.41],[2.257,-2.493],[2.285,-2.543],[2.343,-2.596],[2.399,-2.619],[2.471,-2.619],[2.532,-2.596],[2.58,-2.555]],[[1.09,-0.147],[1.076,-0.133],[0.692,-0.133],[0.678,-0.147],[0.692,-0.161],[0.748,-0.161],[0.781,-0.172],[0.865,-0.161],[1.026,-0.167],[1.076,-0.161]]],"box":[[[6.413,0.064],[1.91,0.064],[1.91,-1.265],[6.413,-1.265]]],"lower":[[[6.413,-1.265],[1.91,-1.265],[1.91,-1.882],[6.413,-1.882]]],"cap":[[[1.91,0.064],[0.292,0.064],[0.292,-1.871],[1.91,-1.871]]],"endcap":[[[0.292,-0.27],[-0.092,-0.27],[-0.092,-1.882],[0.292,-1.882]]],"loop":[[[1.771,0.064],[0.075,0.064],[0.075,-0.225],[1.771,-0.225]]],"cuff":[[[1.993,-1.871],[-0.231,-1.871],[-0.231,-5.94],[1.993,-5.94]]],"strap":[[[1.404,-0.158],[0.297,-0.158],[0.297,-5.84],[1.404,-5.84]]],"keeper":[[[1.493,-3.572],[0.242,-3.572],[0.242,-4.011],[1.493,-4.011]]],"lever":[[[5.635,-1.765],[3.105,-1.576],[3.01,-1.587],[3.01,-2.254],[3.633,-2.31],[5.373,-2.288],[5.601,-2.004]]],"block":[[[3.689,-2.104],[1.815,-2.104],[1.815,-2.949],[3.689,-2.949]]],"notches":[[[5.818,-1.131],[5.106,-1.131],[5.106,-1.254],[5.818,-1.254]],[[3.394,-1.131],[2.705,-1.131],[2.705,-1.254],[3.394,-1.254]]],"groove":[[[6.052,-1.47],[1.926,-1.47],[1.926,-1.515],[6.052,-1.515]]],"pockets":[[[3.061,-2.282],[2.727,-2.282],[2.727,-2.894],[3.061,-2.894]],[[2.994,-1.882],[1.993,-1.882],[1.993,-2.127],[2.994,-2.127]]],"pins":[[[3.427,-1.871],[3.327,-1.871],[3.327,-1.971],[3.427,-1.971]],[[3.427,-2.677],[3.327,-2.677],[3.327,-2.777],[3.427,-2.777]]],"qd":[[[2.705,-2.138],[2.16,-2.138],[2.16,-2.682],[2.705,-2.682]]]},"scaleRefs":["sb-tactical-sba3.length","sb-tactical-sba3.height"],"inputs":{"sb-tactical-sba3.height":5.76,"sb-tactical-sba3.length":6.38},"tolerance":0.006,"photo":"references/sb-tactical-sba3 379c7f22b44e (SB Tactical: SBA3-black-product_image.jpg, the brace's true left side on white, 2000 x 1500)","method":"luminance < 235, closing ×2, largest piece, holes filled; scale from sb-tactical-sba3.length = 6.38 in (x-extent 1141 px → 178.8 px/in) and sb-tactical-sba3.height = 5.76 in (y-extent 1042 px → 180.9 px/in), which agree within 1.2%; mean 179.9 px/in; origin at x min, y max of the outline; Douglas-Peucker at 0.006 in with the extremes kept: 79 points (IoU 0.998 with the full outline); features through the same placement (through: reviewed pixel boxes; box: reviewed pixel boxes; lower: reviewed pixel boxes; cap: reviewed pixel boxes; endcap: reviewed pixel boxes; loop: reviewed pixel boxes; cuff: reviewed pixel boxes; strap: reviewed pixel boxes; keeper: reviewed pixel boxes; lever: reviewed pixel boxes; block: reviewed pixel boxes; notches: reviewed pixel boxes; groove: reviewed pixel boxes; pockets: reviewed pixel boxes; pins: reviewed pixel boxes; qd: reviewed pixel boxes) (tools/trace.py)","via":"harvest","note":"The QD socket's bore and the slit under the loop's bridge are cut through. The lever, the block and the cuff are in the outline; the housing's ledge, the notches and the groove are features; the maker's marks aren't drawn."},"rear":{"plane":"zy","origin":"the loop's tab's middle (the outline's middle over its top 1%, the tab alone: column 1002) and its top: as the side profile, offset down to the tube axis. Seen from the rear: the picture's right is the brace's right","offset":{"y":"tube_axis_below_top"},"points":[[-1.091,-1.094],[-1.081,-1.208],[-1.091,-1.283],[-1.07,-1.337],[-1.075,-1.37],[-1.037,-1.624],[-1.032,-1.797],[-1.01,-1.883],[-1.005,-1.975],[-0.978,-2.034],[-0.978,-2.072],[-0.967,-2.094],[-0.967,-2.175],[-0.951,-2.213],[-0.946,-2.272],[-0.935,-2.283],[-0.935,-2.332],[-0.924,-2.348],[-0.908,-2.45],[-0.913,-2.558],[-0.897,-2.591],[-0.902,-2.618],[-0.886,-2.645],[-0.875,-2.829],[-0.859,-2.872],[-0.859,-3.012],[-0.838,-3.056],[-0.832,-3.131],[-0.821,-3.147],[-0.816,-3.202],[-0.805,-3.212],[-0.8,-3.277],[-0.773,-3.326],[-0.751,-4.363],[-0.778,-4.417],[-0.783,-4.515],[-0.794,-4.536],[-0.794,-4.898],[-0.805,-4.909],[-0.783,-4.941],[-0.789,-5.006],[-0.773,-5.028],[-0.773,-5.066],[-0.762,-5.076],[-0.762,-5.125],[-0.74,-5.19],[-0.74,-5.217],[-0.686,-5.32],[-0.692,-5.33],[-0.67,-5.352],[-0.643,-5.406],[-0.611,-5.438],[-0.562,-5.514],[-0.446,-5.62],[-0.43,-5.62],[-0.392,-5.657],[-0.327,-5.684],[-0.246,-5.738],[-0.176,-5.755],[0.024,-5.76],[0.208,-5.744],[0.235,-5.738],[0.278,-5.711],[0.3,-5.728],[0.319,-5.714],[0.308,-5.703],[0.332,-5.679],[0.397,-5.647],[0.505,-5.555],[0.578,-5.482],[0.611,-5.428],[0.67,-5.357],[0.686,-5.309],[0.708,-5.282],[0.708,-5.255],[0.756,-5.147],[0.762,-5.087],[0.778,-5.071],[0.783,-5.049],[0.794,-4.552],[0.773,-4.417],[0.756,-4.347],[0.746,-4.336],[0.767,-3.753],[0.767,-3.347],[0.805,-3.283],[0.805,-3.261],[0.84,-3.226],[0.905,-3.274],[0.954,-3.274],[1,-3.234],[1.016,-3.191],[1.021,-3.104],[1.005,-2.958],[1.021,-2.931],[1.005,-2.818],[1.01,-2.607],[0.994,-2.569],[0.994,-2.386],[1.01,-2.223],[1.021,-2.207],[1.016,-2.186],[1.054,-2.007],[1.059,-1.937],[1.07,-1.921],[1.075,-1.829],[1.086,-1.807],[1.086,-1.759],[1.102,-1.705],[1.097,-1.683],[1.108,-1.667],[1.113,-1.58],[1.124,-1.548],[1.118,-1.537],[1.135,-1.467],[1.14,-1.364],[1.151,-1.348],[1.156,-1.089],[1.146,-1.029],[1.151,-0.986],[1.14,-0.975],[1.14,-0.905],[1.124,-0.829],[1.129,-0.786],[1.108,-0.732],[1.108,-0.684],[1.097,-0.667],[1.091,-0.608],[1.048,-0.494],[0.997,-0.411],[0.916,-0.357],[0.835,-0.346],[0.821,-0.332],[0.824,-0.324],[0.802,-0.335],[0.727,-0.286],[0.713,-0.273],[0.719,-0.23],[0.697,-0.208],[0.686,-0.17],[0.64,-0.124],[0.586,-0.097],[0.527,-0.081],[0.43,-0.086],[0.408,-0.113],[0.386,-0.119],[0.322,-0.173],[0.294,-0.184],[0.251,-0.184],[0.235,-0.173],[0.197,-0.178],[0.173,-0.154],[0.157,-0.041],[0.132,-0.011],[-0.003,0],[-0.014,0],[-0.138,-0.011],[-0.162,-0.068],[-0.173,-0.132],[-0.192,-0.151],[-0.365,-0.184],[-0.489,-0.249],[-0.554,-0.308],[-0.611,-0.343],[-0.621,-0.37],[-0.675,-0.419],[-0.762,-0.527],[-0.794,-0.554],[-0.886,-0.689],[-0.924,-0.727],[-0.935,-0.759],[-0.983,-0.824],[-1.048,-0.948],[-1.081,-1.035],[-1.081,-1.078]],"features":{"section":[[[-0.23,-0.014],[0.203,-0.014],[0.203,-0.251],[0.511,-0.251],[0.883,-0.975],[0.873,-1.861],[0.775,-2.099],[0.689,-3.18],[0.657,-4.261],[0.635,-5.071],[0.554,-5.422],[0.392,-5.584],[-0.014,-5.644],[-0.419,-5.584],[-0.581,-5.422],[-0.662,-5.071],[-0.684,-4.261],[-0.716,-3.18],[-0.802,-2.099],[-0.9,-1.861],[-0.91,-0.975],[-0.538,-0.251],[-0.23,-0.251]]],"opening":[[[-0.54,-3.337],[-0.54,-3.25],[-0.508,-3.158],[-0.475,-3.115],[-0.413,-3.064],[-0.327,-3.031],[-0.132,-3.01],[0.132,-3.01],[0.246,-3.02],[0.381,-3.048],[0.44,-3.08],[0.497,-3.137],[0.535,-3.202],[0.546,-3.25],[0.546,-3.412],[0.465,-3.537],[0.448,-3.628],[0.438,-3.639],[0.421,-3.704],[0.416,-3.796],[0.405,-3.828],[0.432,-4.044],[0.475,-4.152],[0.519,-4.212],[0.513,-4.271],[0.524,-4.293],[0.524,-4.428],[0.513,-4.839],[0.497,-4.887],[0.497,-4.925],[0.432,-5.066],[0.338,-5.171],[0.262,-5.22],[0.176,-5.257],[0.019,-5.279],[0.016,-5.303],[0.003,-5.317],[-0.024,-5.285],[-0.127,-5.274],[-0.24,-5.23],[-0.257,-5.209],[-0.278,-5.209],[-0.373,-5.12],[-0.411,-5.076],[-0.454,-4.99],[-0.486,-4.882],[-0.492,-4.817],[-0.492,-4.185],[-0.448,-4.131],[-0.443,-4.098],[-0.421,-4.066],[-0.421,-4.044],[-0.405,-4.012],[-0.389,-3.78],[-0.405,-3.645],[-0.416,-3.628],[-0.416,-3.574],[-0.448,-3.52],[-0.465,-3.472],[-0.508,-3.428],[-0.508,-3.347],[-0.527,-3.35]]],"split":[[[-0.046,-5.476],[0.019,-5.476],[0.019,-5.655],[-0.046,-5.655]]]},"scaleRefs":["sb-tactical-sba3.height"],"inputs":{"sb-tactical-sba3.height":5.76},"tolerance":0.006,"photo":"references/sb-tactical-sba3 7c418fd9274e (SB Tactical: SBA3-rear-product_image.jpg, the brace straight from the rear, 2000 x 1500)","method":"luminance < 235, closing ×2, largest piece, holes filled; scale from sb-tactical-sba3.height = 5.76 in (y-extent 1066 px → 185.1 px/in); origin at x center, y max of the outline (x over 0.0–0.01 of the height from the top); Douglas-Peucker at 0.006 in with the extremes kept: 175 points (IoU 0.998 with the full outline); one reference only (the height, read on the pictures on a rifle); the check is the end cap's block, 1.84 in across inside the strap, against the maker's sheet's 'Width (max): 1.8\"'; checks: width in y [-5.0, -4.0] 1.599 ± 0.023 in vs sb-tactical-sba3.cuff_width 1.56 ± 0.05 (provisional): agrees; features through the same placement (section: reviewed pixel boxes; opening: reviewed pixel boxes; split: reviewed pixel boxes) (tools/trace.py)","via":"harvest","note":"Seen from the rear. The silhouette is the body with its strap round it and the strap's loose end; the body's own section is the `section` feature. The window runs fore and aft through the cuff."}},"gaps":[{"what":"The housing's width along its length, and its lower part's and the QD block's (only the end cap's block is shown square, from the rear: the housing is drawn at its width, the lower part set in by an assumed 0.12 in)","need":"a straight view from the front or from below, or the maker's drawing"},{"what":"What the published 6.75 and 9.5 in lengths are measured between (read here as from the end plate's rear face, which the two pictures on a pistol bear out within 0.04 in)","need":"the maker's words, or a picture of it measured"},{"what":"Its right side (Primary Arms' picture of it is on file and is the left's mirror in every feature; the lever's far plate and the QD socket's far cup are drawn as the near ones)","need":"nothing: a check only"}]},"sb-tactical-sba4":{"id":"sb-tactical-sba4","name":"SBA4® AR Adjustable Pistol Stabilizing Brace®","manufacturer":"SB Tactical","sku":"SBA4X-01-SB","url":"https://www.sb-tactical.com/product/sba4/","category":"brace","description":"SB Tactical's five-position pistol stabilizing brace for a mil-spec carbine receiver extension, \"Based on the popular SBM4® brace design\": an M4-style housing round the tube with nine slots down each side, an ambidextrous QD socket through its nose, the adjustment lever in a block under it, a strut of two bars down to a cuff of two flaps at the rear, and a 1 in nylon strap round the cuff through a loop on its top. 10.25 oz. Its shape is read from the maker's straight left and rear views and the maker's pictures of it on a rifle; no drawing or design patent of it is on file.","weight":"sb-tactical-sba4.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"butt":{"origin":[0,0,0],"note":"The brace's rearmost plane on the tube axis (the cuff's rear face): the part frame's origin. The overall length ends here, as it does at a stock's butt (ATF's handbook, 2.1.4: \"the rearmost portion of the weapon\")."},"tube":{"origin":["{.butt_behind_pin_pos1}",0,0],"x":[-1,0,0],"note":"Brace frame: origin on the tube axis in the plane of its rear, +x forward. At its first position (collapsed, as the maker pictures it on a rifle) this anchor sits at the takedown pin's X."}},"interfaces":{"tube":{"type":"receiver_extension","role":"stock","anchor":"tube","params":{"profile":"mil-spec","positions":5},"flips":false,"note":"SB Tactical's page: \"Designed for AR-style platforms utilizing mil-spec carbine receiver extensions, the SBA4 features a reinforced design, 5-position adjustability, an integral ambidextrous QD sling socket\" and \"Because receiver extensions can vary slightly between manufacturers, fitment may differ depending on the specific buffer tube used.\"; its installation sheet: \"The 5-position adjustable SBA3®, SBA4®, SBA5®, and SBA6™ Pistol Stabilizing Braces are compatible with mil-spec carbine receiver extensions (not included).\" Five positions on the tube's six holes: position 1 is the brace collapsed as the maker pictures it, and the tube's sixth step is past where the brace goes."}},"materials":{"body":{"label":"Brace body","finish":"polymer","recolorable":true,"color":"placeholder-polymer-black","sheen":"satin","options":{"black":{"label":"Black","finish":"polymer","color":"placeholder-polymer-black","sheen":"satin","sku":"SBA4X-01-SB","source":"https://www.sb-tactical.com/product/sba4/"},"fde":{"label":"FDE","finish":"polymer","color":"sb-tactical-sba4-fde","sheen":"satin","sku":"SBA4X-02-SB","source":"https://www.sb-tactical.com/product/sba4/"},"odg":{"label":"OD Green","finish":"polymer","color":"sb-tactical-sba4-odg","sheen":"satin","sku":"SBA4X-04-SB","source":"https://www.sb-tactical.com/product/sba4/"},"stealth_gray":{"label":"Stealth Gray","finish":"polymer","color":"sb-tactical-stealth-gray","sheen":"satin","sku":"SBA4X-03M-SB","source":"https://www.primaryarms.com/sb-tactical-sba4-pistol-stabilizing-brace-stealth-grey-no-buffer-tube"}},"default":"black","note":"The maker's page: \"Available in Black, FDE, OD Green\" and \"SKU: SBA4X-01-SB (Black) SBA4X-02-SB (FDE) SBA4X-04-SB (ODG)\"; its material: \"Reinforced polymer construction\". The housing, the lever, its block and boss, the strut and the cuff are the colour in the maker's three side views (dc891b83a89c black, 941602a65010 FDE, 6f789e39e1ad ODG). The FDE and the green are matched under the app's light on the maker's own pictures of each (data/colors/sb-tactical.yaml). Stealth Gray, SBA4X-03M-SB (the maker's December 2021 sheet, UPC 699618783476), is no longer on the maker's page, and still sold: offered since 2026-11-02 (the user: \"make sure we find an active listing for each part in gray before we add it\"), when Primary Arms' page for it was in stock at $99.99 (\"SKU: SBA4X-03M-SB\"). Its colour is matched on Primary Arms' own photographs of it (10b629daaa66 its right, 91a9ebe214f4 its left, 4f8cb7d86ee0 from the rear left), the same studio and poses as its black one's (d2d646f1aa2f, 0ceacff4596a, 70d60c8f9874): separate shoots (the strap folds otherwise, and a slot the black one shows through is closed), the polymer's moulding swirl on the strut. The piece map is the other colourways': the housing, the lever, its block and boss, the strut and the cuff grey; the strap black; the socket's insert bright steel; the lever's pin dark. The older gray-labelled retailer image 4fac0f53781b is the maker's black photo retouched (compared on 2026-10-28: it registers to dc891b83a89c, 58 feature inliers, ECC 0.993, the same strap texture and hardware brightened too), and so are Chattanooga's and TheGunDock's pictures of the grey brace (the maker's black left view tinted, Photoshop in its metadata): not used."},"strap":{"label":"Strap","finish":"polymer","recolorable":false,"color":"placeholder-polymer-black","sheen":"matte","note":"The sheet: \"Comes with adjustable nylon strap for custom fit\", \"Strap Width: 1\"\"; hook and loop, black on all three colourways in the maker's pictures. Drawn as the woven nylon's matte black."},"qd":{"label":"QD socket insert","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"The steel insert in the socket through the nose (\"Integral, ambidextrous QD sling socket\"): bright, unpainted steel on all three colourways in the maker's pictures. No page names its steel or its finish: drawn bright by its look."},"hardware":{"label":"Lever pin","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The pin through the lever's plate, its end in a rounded square each side: black on all three colourways in the maker's pictures (941602a65010, 6f789e39e1ad). No page names its steel or its finish."}},"components":{"body":{"label":"Brace body, lever and block","material":"body"},"hardware":{"label":"Lever pin","material":"hardware"},"strap":{"label":"Strap","material":"strap"},"qd":{"label":"QD socket insert","material":"qd"}},"geometry":{"model":"sb-tactical-sba4.glb","components":{},"approximations":["Built from two views: the maker's straight left side (mirrored; scaled by Wing Tactical's 7 x 5.31 in, which fit it within 0.6%) and the maker's straight rear view (scaled by the 5.31 height and the maker's 2.25 width, within 0.9%). The body is the side outline extruded across and cut by the rear section carried along its whole length: no view from above or below is square, so the housing is the rear face's spade-shaped section all along (the obliques show it so) and nothing narrows ahead of the cuff but what the rear view's section does at each height.","The opening between the cuff's two flaps in the rear view is carried forward as the slot between the strut's two bars, from the cuff to the lever block's front (Wing Tactical's views from below show the two bars and the slot that far); ahead of it the nose is solid across. Under the housing, between the cuff and the nose, the lever block is set in under the housing's side (the side view's shadow along the housing's foot) at the opening's width at its top (0.78 in), and the boss under it at the width the rear view shows it (0.34 in), each as the side view's region: how far the block's face stands in under the housing is that one reading's.","The rear view's opening begins 0.17 in higher than the block's underside in the side view: the two views are put on one origin (the loop's top) and one scale each, and the difference is left, the block being set in over it.","The nine slots in the housing's sides are recesses 0.12 in deep (assumed: no view shows one in section), each a stadium in its box in the side view, on both sides. Primary Arms' right view shows the ground through its front lowest one; the maker's left view doesn't: drawn as the others.","The cavity is the mil-spec tube (std.receiver_extension.milspec_od) and its indexing rail's channel (the rail's width, down to its foot) with 0.01 in of room (assumed), from the mouth to the published 6.75 in depth, on the tube's axis 0.65 in under the housing's top (read on the maker's picture of the brace extended on a rifle).","The QD socket is a bore through the nose (0.29 in) with a steel insert (0.42 in) through it, its own mesh in the `qd` slot; its rim's shape in the insert isn't drawn.","The lever's plate is the block's side: its three small slots and the rounded square round its pin are recesses 0.04 in deep (assumed), each side, where the left view has them (the right side's are the left's mirror: no straight right view shows them clearly); the pin is a steel rod through the block, its ends flush in the square's floor, in the `hardware` slot. The plate's own outline on the block (its sloped top edge, its seam) isn't drawn.","The rear face carries the seam round its spade panel (the inset edge of the spade, the stepped line under it) and the ring round the maker's medallion, each a groove 0.04 in wide (the rear view's dark line, as the shadowed half of a groove) and 0.03 deep (assumed), cut into the rear plane; the medallion's mark isn't drawn.","The strap is a sleeve round the cuff's rear section (its top flattened under the loop), 1 in wide (published) and 0.05 in thick (assumed), the whole height the side view shows it, through the loop on top. It lies in a bed of its own thickness: its outer face is the rear view's silhouette, which the published 2.25 in width is taken to include, and the body under it is drawn in by its thickness. Its loose end, its keeper and its hook-and-loop's two faces aren't drawn.","The loop over the cuff is the side outline above the housing's step at the loop's width in the rear view (0.33 in), with the strap passing under it.","Its weight as a check of its shape takes a glass-filled polyamide's density on trust (0.66 to 0.81 oz to the cubic inch: no page names the resin) and the strap as nylon webbing.","Not drawn: the maker's mark in the medallion, the lever plate's outline, the seams down the cuff's sides. Edges broken at 0.02 in.","Its seat on the tube is read on the maker's picture of it collapsed on a rifle (its mouth 0.29 in behind the castle nut's rear face), not by its lock pin, which no photo shows; the five positions are counted from there at the tube's step."],"ledger":["sb-tactical-sba4.length","sb-tactical-sba4.height","sb-tactical-sba4.width","sb-tactical-sba4.tube_axis_below_top","sb-tactical-sba4.loop_above_top","sb-tactical-sba4.tube_axis_below_crest","sb-tactical-sba4.cavity_depth","sb-tactical-sba4.strap_width","sb-tactical-sba4.qd_ring_diameter","sb-tactical-sba4.qd_bore_diameter","sb-tactical-sba4.block_width","sb-tactical-sba4.boss_width","sb-tactical-sba4.loop_width","sb-tactical-sba4.loop_bar_thickness","sb-tactical-sba4.lever_pin_diameter","sb-tactical-sba4.lever_slot_depth","sb-tactical-sba4.rear_seam_width","sb-tactical-sba4.rear_seam_depth","sb-tactical-sba4.slot_depth","sb-tactical-sba4.strap_thickness","sb-tactical-sba4.bore_clearance","sb-tactical-sba4.butt_behind_pin_pos1"]},"profiles":{"side":{"plane":"xy","origin":"the rearmost point of the cuff (x) and the top of the strap's loop over the cuff (y): the brace's highest point","offset":{"y":"tube_axis_below_crest"},"points":[[0,-0.822],[0.006,-1.041],[0.028,-1.226],[0.039,-1.422],[0.09,-1.714],[0.09,-1.742],[0.079,-1.759],[0.101,-1.787],[0.152,-2.186],[0.163,-2.214],[0.185,-2.432],[0.253,-2.87],[0.275,-3.106],[0.297,-3.224],[0.325,-3.493],[0.342,-3.56],[0.359,-3.751],[0.46,-4.48],[0.466,-4.581],[0.455,-4.593],[0.471,-4.61],[0.483,-5.092],[0.494,-5.159],[0.477,-5.176],[0.499,-5.193],[0.525,-5.235],[0.76,-5.235],[0.772,-5.246],[0.788,-5.246],[0.808,-5.266],[0.797,-5.283],[0.811,-5.286],[0.819,-5.311],[0.839,-5.325],[1.664,-5.325],[1.742,-5.308],[1.787,-5.286],[1.801,-5.272],[1.801,-5.227],[1.815,-5.213],[2.101,-5.207],[2.129,-5.196],[2.194,-5.137],[2.362,-4.845],[2.404,-4.809],[2.432,-4.792],[2.444,-4.798],[2.489,-4.758],[2.758,-4.601],[2.988,-4.45],[3.016,-4.433],[3.027,-4.438],[3.05,-4.41],[3.173,-4.332],[3.852,-3.917],[3.874,-3.905],[3.88,-3.911],[3.908,-3.883],[4.009,-3.821],[4.099,-3.771],[4.105,-3.776],[4.121,-3.754],[4.25,-3.675],[4.323,-3.636],[4.329,-3.642],[4.374,-3.602],[4.525,-3.513],[4.548,-3.501],[4.553,-3.507],[4.61,-3.462],[4.823,-3.344],[4.935,-3.271],[4.957,-3.271],[4.991,-3.238],[5.317,-3.047],[5.468,-2.968],[5.603,-2.884],[5.625,-2.873],[5.631,-2.879],[5.676,-2.839],[5.698,-2.834],[6.091,-2.598],[6.164,-2.559],[6.169,-2.564],[6.293,-2.48],[6.357,-2.41],[6.397,-2.32],[6.402,-2.124],[6.422,-2.087],[6.764,-2.087],[6.837,-2.059],[6.913,-1.995],[6.958,-1.905],[6.963,-1.523],[6.98,-1.507],[6.963,-1.467],[6.963,-1.428],[6.98,-1.411],[6.969,-1.394],[6.969,-1.046],[6.98,-1.024],[6.98,-0.99],[6.93,-0.407],[6.91,-0.376],[6.888,-0.37],[6.848,-0.337],[2.55,-0.337],[2.348,-0.23],[2.118,-0.236],[2.093,-0.205],[2.087,-0.16],[2.062,-0.135],[1.961,-0.084],[1.866,-0.022],[1.81,0],[0.586,-0.006],[0.463,-0.067],[0.311,-0.163],[0.297,-0.227],[0.283,-0.241],[0.042,-0.241],[0.017,-0.278],[0.022,-0.295],[0.011,-0.39]],"features":{"through":[[[5.089,-2.483],[5.075,-2.469],[4.548,-2.48],[4.534,-2.494],[4.528,-2.522],[4.528,-2.662],[4.503,-2.772],[4.458,-2.789],[4.368,-2.8],[4.026,-2.8],[3.931,-2.789],[3.88,-2.772],[3.866,-2.747],[3.866,-2.691],[3.855,-2.657],[3.855,-2.528],[3.849,-2.5],[3.835,-2.486],[3.403,-2.486],[3.083,-2.497],[3.016,-2.491],[2.466,-2.508],[2.264,-2.503],[2.233,-2.466],[2.222,-2.388],[2.228,-2.376],[2.216,-2.343],[2.205,-2.208],[2.2,-2.034],[2.186,-2.02],[2.124,-2.02],[2.087,-2.073],[2.087,-2.343],[2.127,-4.004],[2.132,-4.06],[2.155,-4.088],[2.219,-4.147],[2.281,-4.169],[2.298,-4.169],[2.32,-4.147],[2.348,-4.158],[2.365,-4.141],[2.376,-4.152],[2.399,-4.141],[2.522,-4.057],[2.59,-4.023],[2.668,-3.967],[2.691,-3.961],[3.252,-3.608],[3.347,-3.557],[3.588,-3.4],[3.639,-3.378],[3.947,-3.182],[3.998,-3.159],[4.206,-3.024],[4.963,-2.57],[4.985,-2.542],[4.997,-2.547],[5.019,-2.536]]],"slots":[[[6.13,-0.721],[4.868,-0.721],[4.868,-0.929],[6.13,-0.929]],[[4.66,-0.721],[3.398,-0.721],[3.398,-0.929],[4.66,-0.929]],[[3.173,-0.721],[1.922,-0.721],[1.922,-0.929],[3.173,-0.929]],[[6.13,-1.03],[4.868,-1.03],[4.868,-1.237],[6.13,-1.237]],[[4.66,-1.03],[3.398,-1.03],[3.398,-1.237],[4.66,-1.237]],[[3.173,-1.03],[1.922,-1.03],[1.922,-1.237],[3.173,-1.237]],[[6.13,-1.355],[4.868,-1.355],[4.868,-1.563],[6.13,-1.563]],[[4.66,-1.355],[3.398,-1.355],[3.398,-1.563],[4.66,-1.563]],[[3.173,-1.355],[1.922,-1.355],[1.922,-1.563],[3.173,-1.563]]],"qd":[[[6.826,-1.501],[6.405,-1.501],[6.405,-1.933],[6.826,-1.933]]],"qd_bore":[[[6.759,-1.574],[6.472,-1.574],[6.472,-1.86],[6.759,-1.86]]],"block":[[[5.401,-1.72],[2.202,-1.72],[2.202,-2.483],[5.401,-2.483]]],"boss":[[[4.514,-2.449],[3.852,-2.449],[3.852,-2.786],[4.514,-2.786]]],"strap":[[[1.737,0.031],[0.704,0.031],[0.704,-5.356],[1.737,-5.356]]],"loop":[[[2.062,0.031],[0.267,0.031],[0.267,-0.244],[2.062,-0.244]]],"housing":[[[7.028,0.031],[-0.042,0.031],[-0.042,-1.72],[7.028,-1.72]]],"nose":[[[7.028,0.031],[5.401,0.031],[5.401,-2.214],[7.028,-2.214]]],"lever_slots":[[[3.56,-1.922],[3.527,-1.933],[3.499,-1.961],[3.493,-1.995],[3.499,-2.028],[3.527,-2.056],[3.56,-2.068],[3.908,-2.068],[3.942,-2.056],[3.97,-2.028],[3.975,-1.995],[3.97,-1.961],[3.942,-1.933],[3.908,-1.922]],[[2.96,-2.051],[2.926,-2.068],[2.909,-2.101],[2.909,-2.135],[2.926,-2.169],[2.96,-2.186],[2.994,-2.186],[3.347,-2.085],[3.381,-2.068],[3.398,-2.034],[3.398,-2],[3.381,-1.967],[3.347,-1.95],[3.313,-1.95]],[[2.371,-2.202],[2.343,-2.225],[2.326,-2.253],[2.326,-2.292],[2.348,-2.32],[2.376,-2.337],[2.416,-2.337],[2.763,-2.225],[2.792,-2.202],[2.808,-2.174],[2.808,-2.135],[2.786,-2.107],[2.758,-2.09],[2.719,-2.09]]],"lever_pin":[[[4.267,-1.944],[4.155,-1.944],[4.155,-2.056],[4.267,-2.056]]],"pin_boss":[[[4.385,-1.776],[4.054,-1.776],[4.054,-2.157],[4.385,-2.157]]]},"scaleRefs":["sb-tactical-sba4.length","sb-tactical-sba4.height"],"inputs":{"sb-tactical-sba4.height":5.31,"sb-tactical-sba4.length":7},"tolerance":0.006,"photo":"references/sb-tactical-sba4 dc891b83a89c (SB Tactical SBA4-X_Black_Left_Web.jpg, the black brace straight from its left on white, 1766 x 1766 (mirrored to face +x))","method":"luminance < 235, closing ×2, largest piece, holes filled; scale from sb-tactical-sba4.length = 7 in (x-extent 1244 px → 177.7 px/in) and sb-tactical-sba4.height = 5.31 in (y-extent 949 px → 178.7 px/in), which agree within 0.6%; mean 178.2 px/in; origin at x min, y max of the outline; Douglas-Peucker at 0.006 in with the extremes kept: 124 points (IoU 0.998 with the full outline); features through the same placement (through: reviewed pixel boxes; slots: reviewed pixel boxes; qd: reviewed pixel boxes; qd_bore: reviewed pixel boxes; block: reviewed pixel boxes; boss: reviewed pixel boxes; strap: reviewed pixel boxes; loop: reviewed pixel boxes; housing: reviewed pixel boxes; nose: reviewed pixel boxes; lever_slots: reviewed pixel boxes; lever_pin: reviewed pixel boxes; pin_boss: reviewed pixel boxes) (tools/trace.py)","via":"harvest","note":"The triangle is cut through. The slots, the QD socket, the block, the boss, the strap and the loop are features; the lever's three small slots and its pin, the seams and the maker's mark aren't drawn."},"rear":{"plane":"zy","origin":"the top of the strap's loop, centred: as the side profile, offset down to the tube axis","offset":{"y":"tube_axis_below_crest"},"points":[[-1.121,-1.362],[-1.115,-1.448],[-1.096,-1.522],[-1.065,-1.584],[-1.053,-1.64],[-1.01,-1.726],[-1.004,-1.769],[-0.942,-1.924],[-0.936,-1.967],[-0.892,-2.072],[-0.855,-2.214],[-0.831,-2.27],[-0.8,-2.43],[-0.781,-2.467],[-0.757,-2.634],[-0.732,-2.714],[-0.701,-2.93],[-0.682,-2.998],[-0.676,-3.079],[-0.658,-3.146],[-0.59,-3.739],[-0.59,-3.758],[-0.614,-3.801],[-0.639,-3.881],[-0.639,-4.122],[-0.652,-4.227],[-0.652,-4.721],[-0.633,-4.851],[-0.614,-4.888],[-0.596,-4.968],[-0.528,-5.086],[-0.414,-5.206],[-0.358,-5.249],[-0.253,-5.299],[-0.093,-5.33],[0.093,-5.33],[0.272,-5.292],[0.358,-5.249],[0.414,-5.206],[0.497,-5.123],[0.559,-5.036],[0.602,-4.95],[0.608,-4.906],[0.633,-4.851],[0.652,-4.715],[0.652,-4.233],[0.639,-4.128],[0.639,-3.888],[0.633,-3.85],[0.59,-3.764],[0.59,-3.733],[0.658,-3.14],[0.676,-3.072],[0.682,-2.992],[0.701,-2.924],[0.732,-2.708],[0.757,-2.628],[0.781,-2.467],[0.8,-2.43],[0.824,-2.288],[0.849,-2.232],[0.899,-2.053],[0.929,-1.985],[0.948,-1.905],[0.997,-1.788],[1.016,-1.708],[1.096,-1.516],[1.115,-1.442],[1.121,-1.331],[1.109,-1.3],[1.102,-1.232],[1.071,-1.152],[0.985,-0.991],[0.936,-0.936],[0.818,-0.75],[0.757,-0.682],[0.633,-0.516],[0.513,-0.389],[0.463,-0.352],[0.389,-0.303],[0.296,-0.266],[0.185,-0.204],[0.17,-0.164],[0.151,-0.052],[0.124,-0.025],[0.093,0],[0,0],[-0.093,0],[-0.157,-0.065],[-0.182,-0.201],[-0.296,-0.266],[-0.389,-0.303],[-0.513,-0.389],[-0.639,-0.522],[-0.818,-0.75],[-0.936,-0.936],[-0.991,-0.997],[-1.065,-1.133],[-1.102,-1.232]],"features":{"opening":[[[0.389,-2.313],[0.389,-2.504],[0.383,-2.554],[0.377,-2.603],[0.371,-2.652],[0.364,-2.702],[0.358,-2.751],[0.352,-2.801],[0.352,-2.85],[0.346,-2.899],[0.34,-2.949],[0.333,-2.998],[0.333,-3.048],[0.333,-3.097],[0.327,-3.146],[0.321,-3.196],[0.321,-3.245],[0.321,-3.295],[0.315,-3.344],[0.315,-3.393],[0.309,-3.443],[0.309,-3.492],[0.309,-3.542],[0.303,-3.591],[0.303,-3.64],[0.303,-3.69],[0.303,-3.739],[0.296,-3.789],[0.29,-3.838],[0.29,-3.888],[0.284,-3.937],[0.278,-3.986],[0.272,-4.036],[0.266,-4.085],[0.259,-4.135],[0.253,-4.184],[0.247,-4.233],[0.235,-4.283],[0.222,-4.332],[0.21,-4.382],[0.204,-4.431],[0.185,-4.48],[0.173,-4.53],[0.154,-4.579],[0.13,-4.629],[0.105,-4.678],[0.068,-4.727],[0.043,-4.777],[0.037,-4.826],[0.031,-4.876],[0.012,-4.925],[0,-4.968],[-0.012,-4.925],[-0.031,-4.876],[-0.037,-4.826],[-0.043,-4.777],[-0.068,-4.727],[-0.105,-4.678],[-0.13,-4.629],[-0.154,-4.579],[-0.173,-4.53],[-0.185,-4.48],[-0.204,-4.431],[-0.21,-4.382],[-0.222,-4.332],[-0.235,-4.283],[-0.247,-4.233],[-0.253,-4.184],[-0.259,-4.135],[-0.266,-4.085],[-0.272,-4.036],[-0.278,-3.986],[-0.284,-3.937],[-0.29,-3.888],[-0.29,-3.838],[-0.296,-3.789],[-0.303,-3.739],[-0.303,-3.69],[-0.303,-3.64],[-0.303,-3.591],[-0.309,-3.542],[-0.309,-3.492],[-0.309,-3.443],[-0.315,-3.393],[-0.315,-3.344],[-0.321,-3.295],[-0.321,-3.245],[-0.321,-3.196],[-0.327,-3.146],[-0.333,-3.097],[-0.333,-3.048],[-0.333,-2.998],[-0.34,-2.949],[-0.346,-2.899],[-0.352,-2.85],[-0.352,-2.801],[-0.358,-2.751],[-0.364,-2.702],[-0.371,-2.652],[-0.377,-2.603],[-0.383,-2.554],[-0.389,-2.504],[-0.389,-2.313]]],"tab":[[[-0.167,-0.003],[0.167,-0.003],[0.167,-0.293],[-0.167,-0.293]]],"boss":[[[-0.247,-2.393],[0.093,-2.393],[0.093,-2.64],[-0.247,-2.64]]],"panel":[[[0,-0.343],[0.136,-0.355],[0.29,-0.429],[0.414,-0.54],[0.537,-0.676],[0.661,-0.831],[0.772,-0.985],[0.865,-1.139],[0.92,-1.251],[0.939,-1.356],[0.92,-1.479],[0.865,-1.59],[0.797,-1.664],[0.364,-1.683],[0.364,-2.041],[0,-2.041],[-0.364,-2.041],[-0.364,-1.683],[-0.797,-1.664],[-0.865,-1.59],[-0.92,-1.479],[-0.939,-1.356],[-0.92,-1.251],[-0.865,-1.139],[-0.772,-0.985],[-0.661,-0.831],[-0.537,-0.676],[-0.414,-0.54],[-0.29,-0.429],[-0.136,-0.355]]],"medallion":[[[-0.476,-0.472],[0.463,-0.472],[0.463,-1.411],[-0.476,-1.411]]]},"scaleRefs":["sb-tactical-sba4.height","sb-tactical-sba4.width"],"inputs":{"sb-tactical-sba4.height":5.31,"sb-tactical-sba4.width":2.25},"tolerance":0.006,"photo":"references/sb-tactical-sba4 d3dfd7f2e1fa (SB Tactical SBA4_Rear_web.jpg, straight from behind, 1179 x 1179)","method":"manual polygon (218 points picked on the photo); scale from sb-tactical-sba4.height = 5.31 in (y-extent 863 px → 162.5 px/in) and sb-tactical-sba4.width = 2.25 in (x-extent 363 px → 161.3 px/in), which agree within 0.7%; mean 161.9 px/in; origin at x center, y max of the outline; Douglas-Peucker at 0.006 in with the extremes kept: 99 points (IoU 0.997 with the full outline); features through the same placement (opening: reviewed pixel boxes; tab: reviewed pixel boxes; boss: reviewed pixel boxes; panel: reviewed pixel boxes; medallion: reviewed pixel boxes) (tools/trace.py)","via":"harvest","note":"Seen from behind. The opening between the flaps is carried along the strut's two bars; the tab is the top loop's width."}},"gaps":[{"what":"The brace's own length from its maker (the page's and the sheets' 7.5 in is a length on the rifle from a datum not named: 'Collapsed'); the adopted 7 in is Wing Tactical's","need":"the maker's drawing or a 'brace only' figure, as the SBA5's sheet gives"},{"what":"Where its lock pin stands, and so which of the tube's six holes its five positions use (it is seated by the maker's picture of it collapsed on a rifle)","need":"a view from below or a section through the lever, or the maker's words on which holes it uses"},{"what":"Its widths ahead of the cuff: no view from above or below is square, so the housing is drawn at the rear face's section all along and the strut's bars at the rear view's opening","need":"a straight view from above and from below, or a front view into the mouth"},{"what":"The slots' depth and whether any goes through","need":"a section or a view into one square"},{"what":"The resin, and the strap's thickness","need":"the maker's or a seller's words"}]},"sb-tactical-sba5":{"id":"sb-tactical-sba5","name":"SBA5® AR Adjustable Pistol Stabilizing Brace®","manufacturer":"SB Tactical","sku":"SBA5X-01-SB","url":"https://www.sb-tactical.com/product/sba5/","category":"brace","description":"SB Tactical's five-position brace for a mil-spec carbine receiver extension: a housing round the tube with a wedge groove along its front, an adjustment lever under it with its two pins, a QD sling socket each side in a recessed panel, a strut down to the cuff, and the cuff (modelled after the SB15's): an end cap over two flaps that meet at their foot, with the strap's tab on top and the 1 in nylon strap round it. 9 oz by the maker's newest sheet. Its shape is read from the maker's straight left side picture and its straight view from behind; no drawing or design patent of it is on file.","weight":"sb-tactical-sba5.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"butt":{"origin":[0,0,0],"note":"The brace's rearmost plane on the tube axis (the cuff's rear face): the part frame's origin. The overall length ends here, as it does at a stock's butt (ATF's handbook, 2.1.4: \"the rearmost portion of the weapon\")."},"tube":{"origin":["{.butt_behind_pin_pos1}",0,0],"x":[-1,0,0],"note":"Brace frame: origin on the tube axis in the plane of its rear, +x forward. At its first position (the tube's second hole: its five positions are the tube's rear five) this anchor sits at the takedown pin's X."}},"interfaces":{"tube":{"type":"receiver_extension","role":"stock","anchor":"tube","params":{"profile":"mil-spec","positions":5},"flips":false,"note":"The maker's sheet: \"Gun Compatibility: All platforms capable of accepting a mil-spec carbine receiver extension (not included)\"; its page: \"5-position adjustable configuration\", \"Compatible with standard mil-spec carbine receiver extensions\" and \"Because receiver extensions can vary slightly between manufacturers, overall fit may differ depending on the specific buffer tube being used.\" Five positions on a six-hole tube (`positions: 5`, the page's \"5-position adjustable\"): its first is the tube's second hole (butt_behind_pin_pos1)."}},"materials":{"body":{"label":"Brace body","finish":"polymer","recolorable":true,"color":"placeholder-polymer-black","sheen":"satin","options":{"black":{"label":"Black","finish":"polymer","color":"placeholder-polymer-black","sheen":"satin","sku":"SBA5X-01-SB","source":"https://www.sb-tactical.com/product/sba5/"},"fde":{"label":"FDE","finish":"polymer","color":"sb-tactical-sba5-fde","sheen":"satin","sku":"SBA5X-02-SB","source":"https://www.sb-tactical.com/product/sba5/"},"odg":{"label":"OD Green","finish":"polymer","color":"sb-tactical-sba5-odg","sheen":"satin","sku":"SBA5X-04-SB","source":"https://www.sb-tactical.com/product/sba5/"}},"default":"black","note":"The maker's page: \"Color Black, FDE, OD Green\" and \"SKU: SBA5X-01-SB (Black) SBA5X-02-SB (FDE) SBA5X-04-SB (ODG)\"; its material: \"reinforced polymer construction\" (Wing Tactical: \"Material: Polymer\"). The housing, the lever, the strut, the end cap, the tab and the flaps are the one colour in each (the maker's pictures: 4d01fa8999c1 black, 24198220d197 FDE, c300cd24da81 OD green). The FDE and the green are matched under the app's light on the maker's own pictures of each, by their ratio to the black one's picture of the same series (data/colors/sb-tactical.yaml)."},"strap":{"label":"Strap","finish":"polymer","recolorable":false,"color":"placeholder-polymer-black","sheen":"matte","note":"The sheet: \"Comes with adjustable nylon strap for custom fit\", \"Strap Width: 1\\\"\". Black on all three colours (the maker's FDE and green pictures: their strap reads #181818 and #1a1e1d against the bodies' #a88b63 and #515348)."},"qd":{"label":"QD sling sockets","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The sheet: \"Integral ambidextrous QD sling socket\"; Primary Arms: \"built directly into the housing\". The cup in each socket is dark and glossy on all three colours (the maker's three side pictures; Primary Arms' photographs show a lit metal rim). No page names its metal or finish: drawn as dark steel, by its shine."},"hardware":{"label":"The lever's pins","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The two pins at the lever's rear (the instructions: \"Grasp the adjustment lever at the cross pin\"): dark heads on all three colours. No page names their metal."}},"components":{"body":{"label":"Housing, lever, strut and cuff","material":"body"},"strap":{"label":"Strap","material":"strap"},"qd":{"label":"QD sling sockets","material":"qd"},"hardware":{"label":"The lever's pins","material":"hardware"}},"geometry":{"model":"sb-tactical-sba5.glb","components":{},"approximations":["A visual hull: the maker's straight left side outline (scaled by the sheet's 6.2 in length) across, and its straight view from behind (scaled by the height that gives, 5.16 in, which puts the end cap at the maker's 2.1 in width within 1%) along. The rear outline is made symmetric (the two sides' half-widths averaged row by row: the picture is a little off the middle, and the strap shows past the body on one side at mid height and on the other near the top) and drawn in to 2.1 in at its widest.","The end cap's section is carried the brace's whole length: the housing ahead of the cuff is drawn as wide as the cap, and the strut as wide as the section at its height. No view from above or below is on file to say how much narrower either is; the photographs from behind show the housing's side running flat into the cuff's.","The opening between the cuff's two flaps is drawn at the rim's inner edge the view from behind shows (walls 0.25 in thick), from the cuff's rear face to its front, and never narrower than where the ground shows through; how the flaps' inner faces lean forward isn't read. The split between the flaps at their foot is an assumed 0.02 in.","The bore is the mil-spec tube's own diameter, as deep as the sheet's 6 in cavity, under a wall of 0.086 in at the top (read in an oblique), with the indexing rail's channel at the rail's width down to its foot.","The QD socket's panel, the blank panel ahead of it and the wedge groove along the housing's front are recessed an assumed 0.06 in; the parting lines (round the lever, the cap's seam with the flaps) are an assumed 0.03 in wide and deep. Each QD socket is a steel cup of the bore read in the side picture, reaching two thirds of the way in to the rail's channel (its depth isn't read). The lever's two pins are rods through it, a hair proud of each side.","The strap is a band of the sheet's 1 in width, an assumed 0.06 in thick, round the end cap and the flaps where the side picture has it, over the cap's top under the tab's bar. Its hook-and-loop patch and its metal loop, on the seller's photographs, aren't drawn.","Drawn solid: 21.2 cubic inches of body, where the maker's 9 oz is 11 to 13 cubic inches of a reinforced polymer (1.2 to 1.4 g/cc). The housing, the strut and the cap are cored inside on the real part (no view on file shows how); the model's weight is the ledger's, never its volume's.","Not drawn: the hexagon mark on the cap's rear face, the raised panel round it, the ribs inside the strut's channel, the markings. Edges broken at 0.02 in.","Its seat is its lock pin (the lever's cross pin, 3.91 in ahead of its rear in the maker's side picture) in the tube's second hole: five positions on a six-hole tube, and at the front hole the tube's end would stand at the 6 in cavity's floor. The maker's pictures of it on a pistol are its side picture pasted in, at two places 0.3 in apart, and are kept as a reading."],"ledger":["sb-tactical-sba5.length","sb-tactical-sba5.height","sb-tactical-sba5.width","sb-tactical-sba5.tube_axis_below_top","sb-tactical-sba5.tab_above_housing_top","sb-tactical-sba5.tube_axis_below_housing_top","sb-tactical-sba5.bore_top_wall","sb-tactical-sba5.cavity_depth","sb-tactical-sba5.strap_width","sb-tactical-sba5.strap_thickness","sb-tactical-sba5.lock_pin_ahead_of_butt","sb-tactical-sba5.pin_diameter","sb-tactical-sba5.qd_bore_diameter","sb-tactical-sba5.panel_depth","sb-tactical-sba5.groove_depth","sb-tactical-sba5.split_width","sb-tactical-sba5.flap_wall","sb-tactical-sba5.butt_behind_pin_pos1"]},"profiles":{"side":{"plane":"xy","origin":"the cuff's rearmost point (x) and the top of the strap's tab (y); the housing's top is level in the photo, so the tube axis is horizontal","offset":{"y":"tube_axis_below_top"},"points":[[0,-1.941],[0,-2.013],[0.041,-2.213],[0.072,-2.254],[0.051,-2.305],[0.051,-2.418],[0.092,-2.556],[0.41,-4.305],[0.569,-5.095],[0.597,-5.128],[0.644,-5.149],[0.741,-5.149],[0.808,-5.128],[1.756,-5.144],[1.785,-5.023],[1.803,-5.005],[1.821,-5.023],[1.821,-5.146],[1.844,-5.164],[1.869,-5.159],[1.918,-5.105],[2.887,-3.803],[3.579,-2.946],[3.585,-2.905],[3.651,-2.854],[3.692,-2.787],[3.71,-2.708],[3.736,-2.703],[3.915,-2.769],[3.946,-2.769],[3.972,-2.718],[3.985,-2.762],[4.074,-2.831],[4.131,-2.831],[5.31,-2.682],[5.767,-2.641],[5.849,-2.615],[5.964,-2.438],[6.082,-2.079],[6.072,-2.013],[6,-1.951],[6.01,-1.941],[6,-1.931],[6.082,-1.7],[6.179,-1.556],[6.2,-0.977],[6.2,-0.751],[6.174,-0.515],[6.123,-0.351],[6.069,-0.308],[5.997,-0.292],[5.074,-0.287],[2.105,-0.287],[2.036,-0.228],[2.026,-0.141],[1.995,-0.059],[1.931,-0.01],[1.859,0],[1.49,-0.015],[0.756,-0.01],[0.679,-0.021],[0.626,-0.059],[0.456,-0.305],[0.282,-0.5],[0.133,-0.777]],"features":{"through":[[[3.313,-2.259],[3.295,-2.2],[2.126,-2.205],[2.079,-2.21],[2.056,-2.233],[2.041,-2.413],[2.041,-3.741],[2.067,-3.813],[2.11,-3.856],[2.167,-3.877],[2.259,-3.867],[2.313,-3.823],[3.287,-2.51]]],"strap":[[[1.695,-0.074],[0.71,-0.074],[0.71,-5.151],[1.695,-5.151]]],"tab":[[[2.079,0.018],[0.592,0.018],[0.592,-0.3],[2.079,-0.3]]],"cuff":[[[2.038,-2.295],[-0.049,-2.295],[-0.049,-5.187],[2.038,-5.187]]],"seam":[[[1.951,-2.279],[0.003,-2.279],[0.003,-2.31],[1.951,-2.31]]],"strut":[[[3.746,-2.238],[2.038,-2.238],[2.038,-5.187],[3.746,-5.187]]],"lever":[[[6.218,-1.972],[4.915,-1.972],[4.874,-1.674],[3.736,-1.674],[3.736,-2.854],[6.218,-2.854]]],"pins":[[[3.951,-1.854],[3.874,-1.854],[3.874,-1.931],[3.951,-1.931]],[[3.946,-2.546],[3.869,-2.546],[3.869,-2.623],[3.946,-2.623]]],"qdpanel":[[[2.7,-1.479],[1.951,-1.479],[1.951,-2.187],[2.7,-2.187]]],"blank":[[[3.362,-1.479],[2.721,-1.479],[2.721,-2.208],[3.362,-2.208]]],"qd":[[[2.459,-1.679],[2.09,-1.679],[2.09,-2.049],[2.459,-2.049]]],"chevron":[[[6.141,-0.874],[4.623,-1.387],[6.141,-1.572]]]},"scaleRefs":["sb-tactical-sba5.length"],"inputs":{"sb-tactical-sba5.length":6.2},"tolerance":0.01,"photo":"references/sb-tactical-sba5 4d01fa8999c1 (SB Tactical: SBA5-left-web-1.jpg, the black brace straight from its left on white, 1500 x 1500)","method":"luminance < 200, closing ×2, largest piece, holes filled; scale from sb-tactical-sba5.length = 6.2 in (x-extent 1209 px → 195.0 px/in); origin at x min, y max of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 65 points (IoU 0.998 with the full outline); features through the same placement (through: reviewed pixel boxes; strap: reviewed pixel boxes; tab: reviewed pixel boxes; cuff: reviewed pixel boxes; seam: reviewed pixel boxes; strut: reviewed pixel boxes; lever: reviewed pixel boxes; pins: reviewed pixel boxes; qdpanel: reviewed pixel boxes; blank: reviewed pixel boxes; qd: reviewed pixel boxes; chevron: reviewed pixel boxes) (tools/trace.py)","via":"harvest","note":"The triangle is cut through. The strap, the tab, the cuff, the strut, the lever and its pins, the two panels, the socket and the groove are regions picked on 1.2x gridded crops (the strap down the cuff, the tab over the housing's top line, the cuff behind the strut and under the cap's seam). Its markings aren't drawn."},"rear":{"plane":"zy","origin":"the top of the strap's tab, centred: as the side profile, offset down to the tube axis","offset":{"y":"tube_axis_below_top"},"points":[[-1.127,-1.687],[-1.117,-1.697],[-1.112,-1.768],[-1.097,-1.793],[-1.102,-1.844],[-1.092,-1.894],[-1.097,-1.914],[-1.082,-1.97],[-1.092,-1.985],[-1.077,-2.005],[-1.077,-2.111],[-1.062,-2.126],[-1.047,-2.267],[-1.011,-2.393],[-1.021,-2.429],[-1.001,-2.439],[-0.996,-2.499],[-0.986,-2.514],[-0.986,-2.565],[-1.001,-2.59],[-0.981,-2.62],[-0.976,-2.686],[-0.956,-2.767],[-0.951,-2.827],[-0.961,-2.842],[-0.946,-2.857],[-0.956,-2.868],[-0.941,-2.883],[-0.91,-2.999],[-0.91,-3.039],[-0.9,-3.049],[-0.9,-3.079],[-0.885,-3.115],[-0.885,-3.135],[-0.9,-3.155],[-0.888,-3.147],[-0.875,-3.16],[-0.87,-3.221],[-0.855,-3.251],[-0.86,-3.266],[-0.85,-3.276],[-0.84,-3.392],[-0.85,-3.402],[-0.83,-3.432],[-0.81,-3.523],[-0.81,-3.569],[-0.789,-3.644],[-0.769,-3.821],[-0.699,-4.048],[-0.699,-4.088],[-0.653,-4.3],[-0.638,-4.461],[-0.618,-4.532],[-0.608,-4.633],[-0.618,-4.648],[-0.598,-4.658],[-0.572,-4.789],[-0.507,-4.91],[-0.482,-5.052],[-0.434,-5.12],[-0.368,-5.15],[-0.045,-5.155],[-0.035,-5.145],[-0.015,-5.145],[0.293,-5.16],[0.348,-5.145],[0.406,-5.087],[0.441,-4.961],[0.507,-4.865],[0.512,-4.835],[0.537,-4.799],[0.532,-4.779],[0.547,-4.764],[0.542,-4.744],[0.572,-4.577],[0.593,-4.567],[0.578,-4.542],[0.593,-4.451],[0.618,-4.386],[0.613,-4.355],[0.643,-4.25],[0.653,-4.174],[0.668,-4.159],[0.663,-4.129],[0.689,-4.043],[0.739,-3.765],[0.754,-3.705],[0.779,-3.68],[0.769,-3.67],[0.769,-3.649],[0.779,-3.614],[0.794,-3.599],[0.784,-3.584],[0.794,-3.538],[0.812,-3.516],[0.82,-3.518],[0.81,-3.488],[0.83,-3.478],[0.815,-3.448],[0.83,-3.432],[0.82,-3.422],[0.835,-3.367],[0.83,-3.357],[0.845,-3.327],[0.85,-3.286],[0.865,-3.271],[0.86,-3.256],[0.875,-3.241],[0.865,-3.231],[0.895,-3.16],[0.895,-3.125],[0.915,-3.1],[0.905,-3.084],[0.905,-3.059],[1.016,-2.615],[1.062,-2.388],[1.077,-2.298],[1.072,-2.192],[1.087,-2.146],[1.112,-1.985],[1.117,-1.793],[1.127,-1.783],[1.117,-1.748],[1.127,-1.607],[1.112,-1.49],[1.087,-1.425],[1.087,-1.264],[1.072,-1.183],[1.067,-1.077],[1.031,-1.006],[1.021,-0.926],[0.936,-0.729],[0.941,-0.724],[0.83,-0.547],[0.784,-0.507],[0.787,-0.499],[0.696,-0.424],[0.615,-0.378],[0.58,-0.363],[0.575,-0.368],[0.545,-0.338],[0.54,-0.343],[0.474,-0.303],[0.421,-0.25],[0.416,-0.134],[0.406,-0.098],[0.386,-0.063],[0.348,-0.03],[0.288,-0.015],[0.151,-0.01],[0.121,0],[0.003,-0.003],[-0.025,0],[-0.212,-0.015],[-0.247,-0.03],[-0.29,-0.083],[-0.295,-0.209],[-0.305,-0.24],[-0.368,-0.298],[-0.404,-0.313],[-0.464,-0.358],[-0.532,-0.431],[-0.562,-0.482],[-0.764,-0.936],[-0.86,-1.122],[-0.86,-1.137],[-0.991,-1.395],[-1.021,-1.521],[-1.034,-1.533],[-1.059,-1.533],[-1.092,-1.571],[-1.102,-1.647]],"features":{"channel":[[[-0.416,-2.883],[-0.416,-2.842],[-0.388,-2.82],[-0.05,-2.835],[0.288,-2.825],[0.328,-2.835],[0.356,-2.868],[0.351,-2.994],[0.275,-3.569],[0.26,-3.649],[0.23,-3.72],[0.159,-4.234],[0.149,-4.26],[0.106,-4.308],[0.086,-4.318],[0.076,-4.308],[0.061,-4.323],[-0.146,-4.318],[-0.177,-4.308],[-0.204,-4.28],[-0.23,-4.234],[-0.28,-3.816],[-0.305,-3.72],[-0.34,-3.503],[-0.366,-3.281],[-0.366,-3.256],[-0.356,-3.241],[-0.376,-3.216],[-0.386,-3.074]]],"cap":[[[-1.17,-0.29],[1.15,-0.29],[1.15,-2.131],[-1.17,-2.131]]],"strap":[[[-1.12,-1.274],[-0.958,-1.274],[-0.938,-2.837],[-0.787,-3.947],[-0.636,-4.653],[-0.666,-4.704],[-0.837,-3.947],[-0.999,-2.837],[-1.12,-1.929]],[[0.928,-0.366],[1.09,-0.416],[1.13,-1.274],[1.039,-1.274]]]},"scaleRefs":["sb-tactical-sba5.height"],"inputs":{"sb-tactical-sba5.height":5.16},"tolerance":0.006,"photo":"references/sb-tactical-sba5 3bebaaf0244d (SB Tactical: SBA5-rear-web-1.jpg, the brace straight from behind on white, 1179 x 1179)","method":"luminance < 235, closing ×2, largest piece, holes filled; scale from sb-tactical-sba5.height = 5.16 in (y-extent 1023 px → 198.3 px/in); origin at x center, y max of the outline; Douglas-Peucker at 0.006 in with the extremes kept: 172 points (IoU 0.998 with the full outline); features through the same placement (channel: reviewed pixel boxes; cap: reviewed pixel boxes; strap: reviewed pixel boxes) (tools/trace.py)","via":"harvest","note":"Seen from behind, so z is the rifle's right on the right. The outline takes in the strap where it shows past the body's edge (0.1 in on the left at mid height, on the right near the top): the body is the outline drawn in by the strap's thickness (the model's script)."}},"gaps":[{"what":"The housing's and the strut's widths ahead of the cuff (drawn as wide as the end cap)","need":"a straight view from above or below, or the maker's drawing"},{"what":"Its seat on the tube from a photograph (it is seated by its lock pin in the tube's second hole, ± 0.08 in; the maker's two pistol pictures have its side picture pasted in at two places)","need":"a straight side photograph of it on a lower with both receiver pins in view, at any position"},{"what":"Its height: the maker states none; Wing Tactical's 5.4 in is 4.5% over what the maker's two pictures give with its length and width (5.16 to 5.18)","need":"the maker's height, or a second seller's own"},{"what":"How the body is cored (the model is solid, about twice the maker's 9 oz as polymer)","need":"a view into the cuff or the housing from below, or a section"},{"what":"A design patent or a dimensioned drawing (the maker's patent page lists two utility patents for it, 8,869,444 and 9,354,021, and no design patent)","need":"a drawing from the maker"}]},"sb-tactical-sbpdw-brace":{"id":"sb-tactical-sbpdw-brace","name":"SBPDW® Pistol Stabilizing Brace®","manufacturer":"SB Tactical","sku":"PDW-01-SB","url":"https://www.sb-tactical.com/product/sbpdw/","category":"brace","description":"SB Tactical's three-position brace for an AR pistol, \"Designed in conjunction with Maxim Defense\": a polymer cuff that wraps the forearm, closed by an adjustable nylon strap, on a body that slides over its own receiver extension and two steel guide rods that run forward through a housing at the receiver. The maker: \"The SBPDW brings 3-position adjustability to the AR pistol. Compatible with mil-spec bolt carrier groups and buffers\". Sold only as the whole assembly with its tube (PDW-01-SB): this part is the brace of it, and the SBPDW kit brings both.","weight":"sb-tactical-sbpdw-brace.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"butt":{"origin":[0,0,0],"note":"The brace's rearmost plane on the tube axis: the part frame's origin. The overall length ends here, as it does at a stock's butt (ATF's handbook, 2.1.4: \"the rearmost portion of the weapon\")."},"tube":{"origin":["{.butt_behind_pin_pos1}",0,0],"x":[-1,0,0],"note":"Brace frame: origin on the tube axis in the plane of its rear, +x forward. At its first position (collapsed) this anchor sits at the takedown pin's X: the maker's photo of the brace collapsed on a pistol has its rear 7.24 in behind the receiver's rear face."}},"interfaces":{"tube":{"type":"receiver_extension","role":"stock","anchor":"tube","params":{"profile":"sb-tactical-sbpdw","positions":3},"flips":false,"note":"It rides on its own tube and nothing else: Primary Arms, \"Proprietary buffer tube included\"; AR15Discounts, \"Complete assembly, ready-to-install, including a proprietary buffer tube (does not include buffer/spring)\". Three positions, its own and its tube's (the maker: \"3-position adjustable\"; the receiver extension, sb-tactical-sbpdw-receiver-extension, states the same)."}},"materials":{"body":{"label":"Brace body","finish":"polymer","recolorable":true,"color":"placeholder-polymer-black","sheen":"matte","note":"Sold in black only (the maker's page: \"Color Black\"; AR15Discounts: \"COLOR: Black\"). Its material isn't named on any page read; polymer by its look in every photo. The catalog's polymer black, as SB Tactical's other braces (data/colors/sb-tactical.yaml: the maker's black isn't fitted)."},"strap":{"label":"Strap","finish":"rubber","recolorable":false,"color":"placeholder-black","note":"\"Comes with adjustable nylon strap for custom fit\" (the maker's page); black hook-and-loop webbing in every photo. The catalog has no finish for woven nylon: drawn as its matte rubber, the nearest look (roughness 0.9, no sheen)."},"rods":{"label":"Guide rods","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The two rods the brace rides on, dark and a little glossy in every photo. No page names their metal or finish: drawn as the catalog's dark steel by their look."}},"components":{"body":{"label":"Brace body","material":"body"},"strap":{"label":"Strap","material":"strap"},"rods":{"label":"Guide rods","material":"rods"}},"geometry":{"model":"sb-tactical-sbpdw-brace.glb","components":{},"approximations":["Visual hull of the maker's straight right side photo of the assembly (framed by the span from the housing's front face to the brace's rear, 7.24 in by its photo collapsed on a pistol; the thread's own diameter agrees within 0.5%) and its view from behind (its widths at the published 2.25 in). The view from behind is taken from a little above the axis (the castle nut shows over the cuff's top), and its heights are 22% short of the side photo's: they are stretched to the side outline's top and foot, a ratio of the two, so a height read on the cuff's section is the side photo's and its lean is the rear photo's. Its section holds along the cuff and the strut wherever the side view shows them.","The body over the tube ahead of the cuff is drawn at an assumed width (body_width, 1.45 in: the obliques from above show it about as wide as the castle nut); its lower edge ahead of the strut is where the side photo shows the far rod and the tube's underside under it, so the bore leaves it open underneath there. Its bore is drawn 0.02 in over the tube (bore_d, assumed), from its front back to where the tube's rear stands with the brace collapsed.","The window in each side of the body is cut through into the bore (the tube shows in it in the side photo and in the obliques); its outline is picked on the side photo.","The opening between the cuff's flaps, where the forearm goes, is the rear view's, cut along the whole brace: ahead of the cuff the strut is the flaps' two frames run on to the body, as the obliques show it.","The strap is a band of the cuff's outline the published 1 in wide about the middle the side photo shows, its outer 0.06 in (strap_thickness, assumed) its own piece, all the way round under the flaps' ends as the view from behind has it; drawn as the outline scaled in by that much at its widest and tallest, so on its sloping flanks the skin is a little thinner. Its hook-and-loop face, its buckle and its loose end's own shape aren't drawn (the loose end is in the rear outline at the lower right, along the cuff).","The two rods are drawn level, 1.175 in apart (AR15Discounts' spacing, taken centre to centre), 0.78 in under the tube's axis, 0.334 in round (the left photo's reading), from inside the strut to where their front ends stand on the rifle collapsed (the maker's photo of the pistol: 1.39 in ahead of the receiver's rear face, over the takedown pin's head); their front ends are rounded by a third of their radius. Off the rifle the maker's two side photos have them 0.3 and 0.9 in further forward: how they are held isn't seen. Their detent grooves aren't drawn. On BCM's 16 in rifle the rods run beside the Workhorse lower's rear and stand 0.0045 cubic inches into its model at the takedown pin's lug (app/tests/sb-tactical-sbpdw.test.ts): the rods' height and spacing are each within a few hundredths of where they would clear it, and are kept as read.","Not drawn: the logo plate and its two screws on the cuff's back, the cuff's chamfers but a 0.03 in edge break, the strap's texture. The brace's weight is the whole assembly's published weight less its tube and housing's aluminium as drawn: the model's polymer and steel aren't held to it (no density on file for the polymer)."],"ledger":["sb-tactical-sbpdw-brace.length","sb-tactical-sbpdw-brace.height","sb-tactical-sbpdw-brace.width","sb-tactical-sbpdw-brace.tube_axis_below_top","sb-tactical-sbpdw-brace.butt_behind_pin_pos1"]},"profiles":{"side":{"plane":"xy","origin":"the photo's frame","offset":{},"points":[[-0.003,-0.718],[-0.003,-1.138],[0.145,-3.514],[0.186,-3.75],[0.242,-3.824],[0.361,-3.901],[0.378,-3.942],[0.479,-3.954],[1.383,-3.96],[1.415,-3.945],[1.421,-3.904],[1.442,-3.883],[1.513,-3.871],[1.625,-3.8],[1.676,-3.715],[1.711,-3.496],[1.723,-3.254],[1.817,-2.651],[1.918,-1.853],[2.018,-1.155],[2.042,-1.114],[2.042,-0.588],[2.057,-0.573],[3.227,-0.573],[3.23,0.57],[3.206,0.683],[3.132,0.745],[1.755,0.751],[1.489,0.999],[1.306,1.005],[1.274,1.025],[1.259,1.07],[1.229,1.076],[0.922,1.082],[0.626,1.064],[0.567,1.076],[0.55,1.064],[0.313,1.07],[0.301,1.058],[0.219,1.058],[0.204,1.031],[0.186,0.836],[0.103,0.712],[0.056,0.464]],"features":{"window":[[[1.472,0.145],[2.772,0.145],[2.819,0.086],[2.837,-0.074],[2.801,-0.192],[2.742,-0.251],[2.476,-0.352],[2.122,-0.488],[1.826,-0.553],[1.619,-0.564],[1.543,-0.529],[1.483,-0.428],[1.466,0.015]]],"cuff":[[[-0.183,1.256],[1.383,1.256],[1.383,-4.122],[-0.183,-4.122]]],"top":[[[1.383,1.256],[3.304,1.256],[3.304,-0.576],[1.383,-0.576]]]},"scaleRefs":["sb-tactical-sbpdw-brace.rear_behind_receiver_face"],"inputs":{"sb-tactical-sbpdw-brace.rear_behind_receiver_face":7.24},"tolerance":0.01,"photo":"references/sb-tactical-sbpdw c303ad6a4930 (SB Tactical sbpdw-side-product_image.jpg: the assembly alone, collapsed, straight from the right, 2000 x 1500)","method":"luminance < 225, inside [318, 300, 878, 1190], 1 boxes excluded, closing ×2, largest piece, holes filled; frame from the reviewed holes rear, face (169.2 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.01 in with the extremes kept: 44 points (IoU 0.997 with the full outline); Scaled by the span from the housing's front face to the brace's rear, 7.24 in by the maker's photo of the brace collapsed on a pistol (rear_behind_receiver_face): 169.2 px/in. The thread's top edge, 99.5 px over the axis, gives 168.4 px/in for the standard thread's 1.181 in diameter (0.5% apart); the thread's front end then stands 0.682 in behind the takedown pin, the Army's drawing 0.669.; features through the same placement (window: reviewed pixel boxes; cuff: reviewed pixel boxes; top: reviewed pixel boxes) (tools/trace.py)","via":"harvest","note":"The cuff, the strap's band over it, the body round the tube with its window, and the strut down to the cuff's foot. The body's lower edge ahead of the strut is where the far rod and the tube's underside show under it (row 600): the body is drawn open under the tube there."},"rear":{"plane":"zy","origin":"the outline's top (the strap over the cuff, cut at row 350 where the castle nut stands behind it), centred","offset":{},"points":[[-1.125,-1.374],[-1.096,-1.655],[-0.96,-2.281],[-0.742,-3.167],[-0.598,-3.6],[-0.517,-3.725],[-0.427,-3.808],[-0.315,-3.874],[-0.15,-3.907],[0.019,-3.894],[0.076,-3.907],[0.2,-3.878],[0.571,-3.853],[0.622,-3.806],[0.639,-3.769],[0.63,-3.624],[0.67,-3.536],[0.696,-3.674],[0.725,-3.731],[0.769,-3.758],[0.818,-3.742],[0.837,-3.715],[0.841,-3.641],[0.799,-3.414],[0.853,-3.212],[0.898,-2.693],[1.01,-1.972],[1.117,-1.498],[1.125,-1.304],[1.088,-1.057],[1.026,-0.847],[0.841,-0.517],[0.754,-0.332],[0.668,-0.2],[0.659,-0.163],[0.548,-0.01],[0.538,0],[-0.002,0],[-0.558,0],[-0.591,-0.066],[-0.678,-0.091],[-0.713,-0.134],[-0.729,-0.233],[-0.804,-0.348],[-0.828,-0.472],[-1.051,-0.921],[-1.113,-1.152]],"features":{"opening":[[[-0.639,-1.762],[-0.579,-1.698],[-0.521,-1.673],[-0.183,-1.611],[0.208,-1.611],[0.571,-1.677],[0.655,-1.741],[0.589,-2.124],[0.523,-2.26],[0.49,-2.384],[0.482,-2.705],[0.375,-3.072],[0.301,-3.212],[0.216,-3.288],[0.072,-3.35],[0.021,-3.398],[-0.01,-3.478],[-0.045,-3.394],[-0.089,-3.354],[-0.183,-3.321],[-0.282,-3.251],[-0.326,-3.204],[-0.375,-3.109],[-0.474,-2.763],[-0.462,-2.438],[-0.482,-2.289],[-0.519,-2.178],[-0.589,-2.075]]]},"scaleRefs":["sb-tactical-sbpdw-brace.width"],"inputs":{"sb-tactical-sbpdw-brace.width":2.25},"tolerance":0.01,"photo":"references/sb-tactical-sbpdw c3847cdcc54b (SB Tactical sbpdw-rear-product_image.jpg: the brace from behind, a little above, 2000 x 1500)","method":"luminance < 200, inside [700, 350, 1340, 1310], closing ×2, largest piece, holes filled; scale from sb-tactical-sbpdw-brace.width = 2.25 in (x-extent 546 px → 242.7 px/in); origin at x center, y max of the outline; Douglas-Peucker at 0.01 in with the extremes kept: 47 points (IoU 0.997 with the full outline); Its heights are short of the side view's (the outline is 1.74 times as tall as wide here, 2.23 by the side photo's height and the published width): the camera stands above the axis. The model takes its widths at each height, its heights stretched to the side outline's top and foot.; features through the same placement (opening: reviewed pixel boxes) (tools/trace.py)","via":"harvest","note":"The cuff from behind: its two flaps and the strap round them, the opening between them where the forearm goes (a feature: the flaps' ends meet at the cuff's foot, and the outline closes under it). The strap's loose end hangs at the lower right and is in the outline. The castle nut over the cuff's top is cut off at row 350."}},"gaps":[{"what":"What the published 6.75 in collapsed is measured between (the photos put the brace's rear 7.24 in behind the receiver's rear face)","need":"the maker's drawing or a sentence saying where the length is taken"},{"what":"The brace's weight apart from its tube and housing (worked out from the whole's published weight less the tube's aluminium as drawn)","need":"a review that weighs the brace and the tube apart"},{"what":"The cuff's section: the view from behind is taken from above it, so its heights are stretched to the side photo's in the model; the body round the tube and the strut's own widths (assumed, body_width)","need":"a view square from behind or from below, or from the front with a known size in frame"},{"what":"How the rods are held in the brace and in the housing (off the rifle the maker's two side photos have them 0.3 and 0.9 in further forward than on it)","need":"the maker's exploded view or a photo of the brace off its housing"}]},"sb-tactical-sbpdw-receiver-extension":{"id":"sb-tactical-sbpdw-receiver-extension","name":"SBPDW receiver extension, housing and integral castle nut","manufacturer":"SB Tactical","url":"https://www.sb-tactical.com/product/sbpdw/","category":"receiver_extension","description":"The SBPDW's own aluminium buffer tube with its castle nut made on it, and the housing it carries at the receiver, where an end plate would be; the brace's two rods run through the housing under the tube, and its levers release them. The maker: \"Tighten the tube via the integral castle nut using a castle nut wrench. Be aware that the castle nut and receiver extension are aluminum, care must be taken when using a castle nut wrench.\" AR15Discounts: \"The end plate and castle nut are integral to the assembly\". It takes the rifle's own carbine buffer and spring (\"SBPDW is compatible with mil-spec receivers and carbine length buffers and springs\"). Sold only with the brace, as the SBPDW (PDW-01-SB).","weight":"sb-tactical-sbpdw-receiver-extension.weight","occupies":["end_plate","castle_nut"],"integral":["end_plate","castle_nut"],"brings":[],"seats":{},"requires":[],"anchors":{"receiver_thread":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the tube axis at the takedown pin's X, +x rearward."},"tube":{"origin":[0,0,0],"x":[1,0,0]},"bore":{"origin":["0in - {std.ar15.upper_rear_face_x}",0,0],"x":[1,0,0],"note":"On the tube axis where a buffer's front face rests with the bolt forward: against the carrier's rear end, which stands at the upper receiver's rear face (the Army's drawings). The buffer and its spring are placed from it."}},"interfaces":{"receiver_thread":{"type":"ar15.buffer_tube_mount","role":"tube","anchor":"receiver_thread","params":{},"flips":false,"note":"The maker: \"The 3-position adjustable SBPDW™ Pistol Stabilizing Brace® is compatible with mil-spec AR receivers.\" AR15Discounts: \"Not compatible with Freedom Ordnance FX-9 lowers or SIG M400/516 lowers with integral QD sockets\"."},"tube":{"type":"receiver_extension","role":"tube","anchor":"tube","params":{"profile":"sb-tactical-sbpdw","od":"={.tube_od}","positions":3,"step":"={.position_step}"},"flips":false,"note":"Its own brace's and no other: the brace rides on two rods through the housing, not on a stock's tube (Primary Arms: \"Proprietary buffer tube included\"). Three positions (\"3-position adjustable\"), a step of half the published travel."},"bore":{"type":"ar15.extension_bore","role":"tube","anchor":"bore","params":{},"flips":false}},"materials":{"tube":{"label":"Receiver extension and castle nut","finish":"anodized","recolorable":false,"color":"placeholder-black","note":"\"Castle nut / receiver extension is aluminum\" (the maker's instructions); black in every photo, sold so. The finish isn't named: anodized by its look (a satin black, as the housing)."},"housing":{"label":"Housing and levers","finish":"anodized","recolorable":false,"color":"placeholder-black","note":"Black in every photo, the tube's satin; its metal isn't named on any page read, and it is drawn as aluminium. Its two levers (the takedown lever hanging at its rear, the ribbed adjustment latch under its middle) are drawn with it."}},"components":{"tube":{"label":"Receiver extension and castle nut","material":"tube"},"housing":{"label":"Housing","material":"housing"}},"geometry":{"model":"sb-tactical-sbpdw-receiver-extension.glb","components":{},"approximations":["The tube is turned from the ledger: its thread the standard's (1 3/16-16, a helix between the Army drawing's limits, as long as the mil-spec carbine's: no page gives this tube's), its front face where the drawings put a mil-spec tube's (the maker's side photo agrees within 0.013 in), its body behind the thread at the side photo's 1.141 in, bored to the drawing's inch to the depth AR15Discounts states (6.920 in), closed by a rear wall drawn as the mil-spec carbine's (0.072 in, assumed: the tube's rear end is inside the brace in every photo) with no vent. It is a plain round tube behind the nut: the brace rides on its rods, not on the tube, and no rail or holes show on it.","The castle nut is made on the tube (\"the integral castle nut\"), at the side photo's length and diameter, with eight notches 0.11 in wide and 0.2 deep in its rear face, at 45°, turned 22.5° off the vertical: six of them show in the photos (two on each side, two at the top), the two at the bottom are hidden behind the housing in every view.","The housing is the side photo's outline of it extruded across and cut to a section drawn from the figures: the round over the tube (its 1.418 in), the two rods' bosses at its lower corners (the brace's rod spacing and diameter, an assumed 0.09 in wall round each: ear_wall) and its foot under them at the photo's 1.26 in below the axis, as the convex hull of those; the front oblique (6020c5e68ca5) shows the rods coming out of its lower corners so, and no view is square to its front or underside. Its bore takes the thread's crests (assumed: the tube goes in thread first); the rods' bores are drawn 0.016 in over the rods. Its tail under the castle nut stops at the nut's outside.","The housing bears on the receiver's rear face where an end plate does (\"The end plate and castle nut are integral to the assembly\"); its front lip, 0.09 in proud at its foot, is the side photo's, and on BCM's 16 in rifle (the Workhorse lower) it stands 0.013 cubic inches into the lower's model under the buffer tower (app/tests/sb-tactical-sbpdw.test.ts): the lip may sit under the receiver's tang, which no photo on file shows from below. Kept as photographed, not cut. Its metal isn't named: drawn and weighed as aluminium, as the tube.","The takedown lever and the ribbed adjustment latch are plates on the housing's centre plane at the side photo's outline of each, their widths assumed (lever_width, latch_width); their ribs, pivots and springs aren't drawn. The QD socket the sellers place \"at 6 o'clock position on housing\" isn't drawn: no photo on file shows the housing from below."],"ledger":["sb-tactical-sbpdw-receiver-extension.tube_od","sb-tactical-sbpdw-receiver-extension.tube_front_behind_pin","sb-tactical-sbpdw-receiver-extension.tube_length","sb-tactical-sbpdw-receiver-extension.position_step","sb-tactical-sbpdw-receiver-extension.housing_length","sb-tactical-sbpdw-receiver-extension.housing_od","sb-tactical-sbpdw-receiver-extension.nut_od","sb-tactical-sbpdw-receiver-extension.nut_length"]},"profiles":{"side":{"plane":"xy","origin":"the photo's frame","offset":{},"points":[[1.016,-1.167],[1.022,-1.262],[1.048,-1.288],[1.125,-1.288],[1.146,-1.309],[1.152,-1.38],[1.172,-1.395],[1.432,-1.389],[1.71,-1.283],[1.864,-1.265],[3.146,-1.259],[3.312,-1.271],[3.324,-1.259],[3.554,-1.259],[3.563,-1.132],[3.598,-1.114],[3.598,-0.564],[3.158,-0.561],[3.143,-0.547],[3.143,0.6],[3.114,0.618],[3.114,0.677],[3.099,0.697],[3.081,0.709],[1.763,0.715],[1.178,0.715],[1.14,0.677],[1.122,0.618],[1.122,-1.15],[1.107,-1.164]],"features":{"lever":[[[3.566,-1.238],[3.33,-1.238],[3.33,-1.936],[3.566,-1.936]]],"latch":[[[3.134,-1.238],[2.484,-1.238],[2.484,-1.593],[3.134,-1.593]]]},"scaleRefs":["sb-tactical-sbpdw-receiver-extension.housing_front_behind_pin","sb-tactical-sbpdw-brace.rear_behind_receiver_face"],"inputs":{"sb-tactical-sbpdw-brace.rear_behind_receiver_face":7.24,"sb-tactical-sbpdw-receiver-extension.housing_front_behind_pin":1.125},"tolerance":0.01,"photo":"references/sb-tactical-sbpdw c303ad6a4930 (SB Tactical sbpdw-side-product_image.jpg: the assembly alone, collapsed, straight from the right, 2000 x 1500)","method":"luminance < 225, inside [1138, 370, 1580, 745], 4 boxes excluded, closing ×2, largest piece, holes filled; frame from the reviewed holes face, rear (169.2 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.01 in with the extremes kept: 30 points (IoU 0.998 with the full outline); The frame is the brace's trace's (169.2 px/in), mirrored: this part's x runs rearward.; features through the same placement (lever: reviewed pixel boxes; latch: reviewed pixel boxes) (tools/trace.py)","via":"harvest","note":"The housing's side: its round top over the tube (1.42 in), the block under it the brace's rods run in, down to 1.26 in under the axis, its front lip 0.09 in proud of the face at the foot, and its tail under the castle nut. Its levers are features."}},"gaps":[{"what":"Not sold alone: no number, no price, no weight of its own (worked out from its sizes as aluminium)","need":"a page selling the tube and housing alone, or a review that weighs them apart from the brace"},{"what":"Its depth (6.920 in) is one seller's; its rear wall, the end of the tube and anything on it are inside the brace in every photo","need":"the maker's drawing, or a photo of the tube out of the housing and the brace"},{"what":"The housing's width at its lower corners (assumed from the rods' spacing and a wall), and the shape of its underside and front from square on","need":"a view of the assembly from below or from the front, square, with a known size in frame"},{"what":"Whether the 'integral' end plate takes a sling (the QD socket the pages name is the housing's, at 6 o'clock: \"QD attachment point at 6 o'clock position on housing\"; no photo on file shows its cup from below)","need":"a photo of the housing from below"}]},"scalarworks-leap-01-micro-142":{"id":"scalarworks-leap-01-micro-142","name":"LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.42 in","manufacturer":"Scalarworks","sku":"SW0100","url":"https://scalarworks.com/shop/quick-detach-mounts/leap-01/","category":"optic_mount","description":"Scalarworks' quick-detach mount for an Aimpoint Micro T-2 and the dots cut for its footprint, the dot's axis 1.42 in over the rail (\"Optic center height over rail ... SW0100 : 1.42\"\", \"Co-Witness ... SW0100 : Absolute\"). A frame of 7075 with a window through its sides and its ends, leaning forward over its clamp (\"Forward lean for additional magnifier space\", Primary Arms), clamped by one knurled wheel on the left turned by hand (\"Close clamp by turning ClickDrive wheel as tightly as you can by hand (Do not use tools).\"). 43 g. Out of stock at its maker on 2026-11-03.","weight":"scalarworks-leap-01-micro-142.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":[0,0,0],"note":"Mount frame: on the rail's top under the ClickDrive wheel's shaft, +x forward. It has no cross bolt: the wheel turns a shaft that crosses the rail in a slot (the maker's side photo of this height has it in the slot midway between the two that show), and that slot is the one the build names."},"deck":{"origin":["{.deck_x}","{.deck_above_rail}",0],"note":"On the deck's floor at the footprint's middle, where a dot's base is put (D101): the T-2's foot sits down on it between the deck's two rims."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":"={.clamp_rear}","clamp_front":"={.clamp_front}"},"flips":false,"note":"One clamp, closed by hand: the manual's \"Open clamp no further than internal stops allow.\", \"Hook Leap mount onto rail from ClickDrive side.\" and \"Close clamp by turning ClickDrive wheel as tightly as you can by hand (Do not use tools).\" Its reach along the rail is its foot's two ends about the shaft, as the maker's side photo has them. The page: \"Rails MIL-STD-1913 Picatinny\". Nothing the maker publishes says where on a rifle's rail it goes; its pictures on rifles have it on the receiver's rail."},"deck":{"type":"optic_footprint","role":"deck","anchor":"deck","params":{"pattern":"aimpoint_micro"},"flips":false,"note":"Cut for the Aimpoint Micro T-2's footprint: \"LEAP/01 redefines the standard for mounting your Aimpoint Micro T-2 footprint compatible optic to your AR-15's Picatinny top rail.\" Its list: \"Aimpoint red dot sights Micro T-2, H-2, T-1, H-1, CompM5\", with Holosun's 403, 503, 515 and 530, Primary Arms' Advanced Micro Dot and Microdot, SIG's ROMEO4 and ROMEO5 and Vortex's CROSSFIRE, SPARC II and SPARC SOLAR (the maker's page). Four M3 screws hold the dot: \"Fasteners (4) M3x4mm Nylon patched\"; the manual: \"MAX TORQUE 10 INCH-LBS\"."}},"materials":{"mount":{"label":"Mount","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized_matte","color":"placeholder-black","sku":"SW0100","source":"https://scalarworks.com/shop/quick-detach-mounts/leap-01/"}},"default":"black","note":"The one colour it is sold in: the maker's page offers a height and a package, no colour; MidwayUSA's name for it is \"Matte Black\". Scalarworks: \"Materials 7075-T6 Aluminum / 4140H Steel\", \"Finishes Type III Anodizing / Flash Nitride\": the aluminium hard anodized, and in the maker's studio photos of this height (351188c51fd3, f703a832b60e) a matte charcoal black with no hard highlight, so `anodized_matte`. A black on anodize isn't fitted to a photo: the placeholder black. Not drawn: the engraving."},"hardware":{"label":"Wheel, shaft and set screw","finish":"nitride","recolorable":false,"color":"steel-nitride-black","note":"The steel: the ClickDrive wheel and its shaft, and the set screw in the rear end. Scalarworks: \"4140H Steel\" with \"Flash Nitride\". In the maker's photos the wheel is a glossier black than the body, its face bearing \"SCALARWORKS\" in gold (not drawn). A black on steel isn't fitted to a photo (data/colors/steel.yaml, steel-nitride-black)."}},"components":{"mount":{"label":"Mount","material":"mount"},"hardware":{"label":"Wheel","material":"hardware"}},"geometry":{"model":"scalarworks-leap-01-micro-142.glb","components":{},"approximations":["The body is the two traced outlines' visual hull: the maker's photo of the left side (scaled by the rail's own slots) and its drawing from behind (scaled by the rail drawn in section and the T-2's axis), the drawing's right half mirrored for the left (\"the Leap mount is symmetrical\"). Through it, the window through its sides as the photo has it (its lower edge, hidden behind the wheel, carried on straight at the height it has beside the wheel) and the window through its ends as the drawing has its throat: the four corner posts between are what is left. The photo reads the near face 1.3 to 1.7% larger than the drawing gives (the lens is nearer it than the rail's middle): the outline is drawn as read.","The deck is drawn flat across at its floor, where a dot's base sits (deck_above_rail, the maker's 1.42 in less the T-2's axis over its base; the drawing has the floor 0.022 in lower). The two rims along its sides, which stand 0.079 in over the floor (the drawing) (rim_top_above_rail), and the square lug in its middle aren't drawn: every Micro dot on file is drawn with a flat base as wide as its housing, and they would stand inside it. The four screw holes in the floor aren't drawn either: no view gives their places.","The clamp's channel is the rail's own head in section (MIL-STD-1913's) from the rail's top down to the lower gauge line, the jaws' hooks under that as the drawing has them. The telescoping jaw on the right is a piece of its own, split where the drawing draws its line (up the right wall 0.51 in out, across at 0.195 in, and in under the rail's head). On its outer face, three round heads in a row, each flush in a hole a ring wider than it: the shaft's end and the two guide pins' (\"A pair of hardened steel precision ground pins is press fitted to the clamp and act as guides.\"), at the places Primary Arms' photo of the LEAP/02's right side gives them: no view of this mount's right side is on file. The shaft across the rail and the pins inside aren't drawn.","The ClickDrive wheel: twenty teeth (counted on the side photo) between this height's photo's two diameters, its outer face flush with the clamp's left face and as thick as the drawing has it, in a round pocket in the left wall (its clearance assumed), its face dished inside its rim and a socket in its middle (both depths assumed). The set screw in the rear end, in line with the wheel: a hole at the drawing's place and size, its end a little way in (both depths assumed). Not drawn: the engraving and the wheel's gold lettering.","Its metal as drawn: 0.88 cubic inches of 7075 and the steel, 46.3 g, for the maker's 43 g (the rims and the lug left out; the screw holes and the shaft's bore in the body not cut)."],"ledger":["scalarworks-leap-01-micro-142.deck_above_rail","scalarworks-leap-01-micro-142.deck_x","scalarworks-leap-01-micro-142.mount_length","scalarworks-leap-01-micro-142.width","scalarworks-leap-01-micro-142.body_width","scalarworks-leap-01-micro-142.clamp_below_rail"]},"profiles":{"side":{"plane":"xy","origin":"on the rail's top under the ClickDrive wheel's shaft, which lies in the rail slot midway between the two that show","offset":{},"points":[[-0.938,0.105],[-0.938,0.02],[-0.908,0.018],[-0.89,0],[-0.888,-0.233],[0.673,-0.233],[0.991,0.555],[1.028,0.612],[1.093,0.669],[1.109,0.709],[1.133,0.73],[1.133,0.811],[1.101,0.823],[1.093,0.884],[1.071,0.906],[-0.653,0.906],[-0.667,0.892],[-0.667,0.847],[-0.683,0.807],[-0.721,0.772],[-0.876,0.683],[-0.89,0.665],[-0.898,0.191],[-0.91,0.13],[-0.924,0.107]],"features":{"window":[[[0.618,0.559],[0.594,0.628],[0.543,0.679],[0.466,0.703],[-0.093,0.712],[-0.178,0.695],[-0.247,0.667],[-0.421,0.545],[-0.48,0.478],[-0.5,0.426],[-0.505,0.247],[-0.496,0.199],[-0.476,0.162],[-0.434,0.124],[-0.401,0.107],[-0.344,0.099],[-0.278,0.109],[-0.286,0.142],[-0.271,0.156],[-0.251,0.156],[-0.229,0.178],[-0.229,0.219],[-0.215,0.233],[-0.178,0.229],[-0.156,0.247],[-0.138,0.286],[-0.089,0.274],[-0.044,0.314],[-0.004,0.29],[0.02,0.29],[0.061,0.31],[0.085,0.278],[0.106,0.27],[0.154,0.278],[0.164,0.243],[0.183,0.225],[0.227,0.221],[0.237,0.211],[0.233,0.174],[0.256,0.148],[0.29,0.134],[0.282,0.109],[0.288,0.103],[0.337,0.107],[0.361,0.099],[0.41,0.111],[0.464,0.154],[0.493,0.199],[0.606,0.474]]]},"scaleRefs":["std.picatinny.slot_pitch"],"inputs":{"std.picatinny.slot_pitch":0.394},"tolerance":0.006,"photo":"references/scalarworks-leap-01-micro-142 351188c51fd3 (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.42-side-SW0100.jpg: SW0100 alone on a rail section, straight left side, 1200 x 1200)","method":"luminance < 200, inside [300, 465, 830, 758], 2 polygons excluded, closing ×1, largest piece, holes filled; frame from the reviewed holes slot_front, slot_rear (246.7 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.006 in with the extremes kept: 25 points (IoU 0.997 with the full outline); features through the same placement (window: the window through the mount's sides (the white ground through both)) (tools/trace.py)","via":"harvest","note":"The mount's left side, turned to face +x: the deck (its rims' top, with the step at its front end), the leaning front leg, the upright rear leg with its scooped top corner, and the clamp down to its foot under the rail's top; the wheel's teeth below the foot are left out. The window through both sides is a feature."},"end":{"plane":"zy","origin":"on the rail's top at its middle","offset":{},"points":[[-0.673,-0.004],[-0.664,-0.223],[-0.654,-0.227],[-0.365,-0.23],[-0.358,-0.17],[-0.416,-0.111],[-0.416,-0.09],[-0.318,0.008],[0.317,0.008],[0.418,-0.094],[0.418,-0.109],[0.356,-0.171],[0.362,-0.23],[0.529,-0.231],[0.561,-0.216],[0.602,-0.178],[0.642,-0.138],[0.666,-0.094],[0.669,0.218],[0.646,0.277],[0.507,0.416],[0.478,0.469],[0.471,0.892],[0.306,0.893],[0.27,0.813],[-0.231,0.814],[-0.267,0.814],[-0.28,0.827],[-0.305,0.893],[-0.47,0.893],[-0.475,0.479],[-0.496,0.432],[-0.53,0.395],[-0.609,0.315],[-0.639,0.316],[-0.664,0.29]],"features":{"window":[[[0.233,0.698],[0.259,0.694],[0.282,0.682],[0.3,0.664],[0.311,0.641],[0.316,0.615],[0.315,0.264],[0.311,0.239],[0.3,0.216],[0.281,0.198],[0.258,0.186],[0.233,0.182],[-0.233,0.182],[-0.259,0.187],[-0.282,0.198],[-0.3,0.216],[-0.312,0.239],[-0.316,0.265],[-0.316,0.616],[-0.311,0.642],[-0.3,0.665],[-0.282,0.683],[-0.259,0.694],[-0.233,0.699]]]},"scaleRefs":["std.picatinny.top_width","std.picatinny.bevel_gauge_apart","std.picatinny.lower_gauge_below_top","scalarworks-leap-01-micro-142.optical_axis_above_rail"],"inputs":{"scalarworks-leap-01-micro-142.optical_axis_above_rail":1.42,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"tolerance":0.006,"photo":"references/scalarworks-leap-01-micro-142 c08b4e430885 (Scalarworks' technical drawing of SW0100 (scalarworks-SW0100-diagram-A.png): the mount with a T-2 on it, from behind, 1200 x 1200)","method":"luminance < 150, inside [368, 786, 834, 1171], 2 polygons excluded, closing ×2, largest piece, holes filled, opening after the fill 5 px ×1, inset 1 px (half the outline's stroke); frame from the reviewed holes rail_left, rail_right, axis (339.1 px/in, rms 0.002 in over 3 points); origin at the photo's frame; Douglas-Peucker at 0.006 in with the extremes kept: 36 points (IoU 0.994 with the full outline); features through the same placement (window: the window through the mount from end to end, inside its throat (the inner of the two outlines drawn round it)) (tools/trace.py)","via":"harvest","note":"The mount seen from behind, z to the rifle's right: the rims' tops, the body down to its shoulders, the clamp as wide as the drawing has it, and its jaws round the rail's head to their foot (the left jaw with the wheel's knurl under it: the model mirrors the right half). Between the rims the outline's top is the floor. The window through the mount end to end is a feature."}},"gaps":[{"what":"A view of the deck from straight above, with a scale","need":"where the four screw holes and the lug stand on the floor, and the rims' width: only one oblique from above is on file (Wing Tactical's, filed with the 1.57 in, its height not said), so neither is drawn"},{"what":"The maker's word on where on the rail it goes","need":"nothing on its page or in its manual says receiver only or not across the receiver's and the handguard's rails; it is started and advised as any sight is"}]},"scalarworks-leap-01-micro-157":{"id":"scalarworks-leap-01-micro-157","name":"LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.57 in","manufacturer":"Scalarworks","sku":"SW0110","url":"https://scalarworks.com/shop/quick-detach-mounts/leap-01/","category":"optic_mount","description":"Scalarworks' quick-detach mount for an Aimpoint Micro T-2 and the dots cut for its footprint, the dot's axis 1.57 in over the rail (\"Optic center height over rail ... SW0110 : 1.57\"\", \"Co-Witness ... SW0110 : Lower-Third\"). A frame of 7075 with a window through its sides and its ends, leaning forward over its clamp (\"Forward lean for additional magnifier space\", Primary Arms), clamped by one knurled wheel on the left turned by hand (\"Close clamp by turning ClickDrive wheel as tightly as you can by hand (Do not use tools).\"). 45 g.","weight":"scalarworks-leap-01-micro-157.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":[0,0,0],"note":"Mount frame: on the rail's top under the ClickDrive wheel's shaft, +x forward. It has no cross bolt: the wheel turns a shaft that crosses the rail in a slot (the maker's side photo has it in the slot midway between the two that show), and that slot is the one the build names."},"deck":{"origin":["{.deck_x}","{.deck_above_rail}",0],"note":"On the deck's floor at the footprint's middle, where a dot's base is put (D101): the T-2's foot sits down on it between the deck's two rims."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":"={.clamp_rear}","clamp_front":"={.clamp_front}"},"flips":false,"note":"One clamp, closed by hand: the manual's \"Open clamp no further than internal stops allow.\", \"Hook Leap mount onto rail from ClickDrive side.\" and \"Close clamp by turning ClickDrive wheel as tightly as you can by hand (Do not use tools).\" Its reach along the rail is its foot's two ends about the shaft, as the maker's side photo has them. The page: \"Rails MIL-STD-1913 Picatinny\". Nothing the maker publishes says where on a rifle's rail it goes; its pictures on rifles have it on the receiver's rail."},"deck":{"type":"optic_footprint","role":"deck","anchor":"deck","params":{"pattern":"aimpoint_micro"},"flips":false,"note":"Cut for the Aimpoint Micro T-2's footprint: \"LEAP/01 redefines the standard for mounting your Aimpoint Micro T-2 footprint compatible optic to your AR-15's Picatinny top rail.\" Its list: \"Aimpoint red dot sights Micro T-2, H-2, T-1, H-1, CompM5\", with Holosun's 403, 503, 515 and 530, Primary Arms' Advanced Micro Dot and Microdot, SIG's ROMEO4 and ROMEO5 and Vortex's CROSSFIRE, SPARC II and SPARC SOLAR (the maker's page). Four M3 screws hold the dot: \"Fasteners (4) M3x4mm Nylon patched\"; the manual: \"MAX TORQUE 10 INCH-LBS\"."}},"materials":{"mount":{"label":"Mount","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized_matte","color":"placeholder-black","sku":"SW0110","source":"https://scalarworks.com/shop/quick-detach-mounts/leap-01/"}},"default":"black","note":"The one colour it is sold in: the maker's page offers a height and a package, no colour; MidwayUSA's name for it is \"Matte Black\". Scalarworks: \"Materials 7075-T6 Aluminum / 4140H Steel\", \"Finishes Type III Anodizing / Flash Nitride\": the aluminium hard anodized, and in the maker's studio photos (e656d3c79e0b, 4c1fcbf8e389) a matte charcoal black with no hard highlight, so `anodized_matte`. A black on anodize isn't fitted to a photo: the placeholder black. Not drawn: the engraving."},"hardware":{"label":"Wheel, shaft and set screw","finish":"nitride","recolorable":false,"color":"steel-nitride-black","note":"The steel: the ClickDrive wheel and its shaft, and the set screw in the rear end. Scalarworks: \"4140H Steel\" with \"Flash Nitride\". In the maker's photos the wheel is a glossier black than the body, its face bearing \"SCALARWORKS\" in gold (not drawn). A black on steel isn't fitted to a photo (data/colors/steel.yaml, steel-nitride-black)."}},"components":{"mount":{"label":"Mount","material":"mount"},"hardware":{"label":"Wheel","material":"hardware"}},"geometry":{"model":"scalarworks-leap-01-micro-157.glb","components":{},"approximations":["The body is the two traced outlines' visual hull: the maker's photo of the left side (scaled by the rail's own slots) and its drawing from behind (scaled by the rail drawn in section and the T-2's axis), the drawing's right half mirrored for the left (\"the Leap mount is symmetrical\"). Through it, the window through its sides as the photo has it (its lower edge, hidden behind the wheel, carried on straight at the height it has beside the wheel) and the window through its ends as the drawing has its throat: the four corner posts between are what is left. The photo reads the near face 1.3% larger than the drawing and Wing Tactical's length give (the lens is nearer it than the rail's middle): the outline is drawn as read.","The deck is drawn flat across at its floor, where a dot's base sits (deck_above_rail, the maker's 1.57 in less the T-2's axis over its base; the drawing has the floor 0.016 in lower). The two rims along its sides, which stand 0.065 in over the floor (rim_top_above_rail), and the square lug in its middle aren't drawn: every Micro dot on file is drawn with a flat base as wide as its housing, and they would stand inside it. The four screw holes in the floor aren't drawn either: no view gives their places.","The clamp's channel is the rail's own head in section (MIL-STD-1913's) from the rail's top down to the lower gauge line, the jaws' hooks under that as the drawing has them. The telescoping jaw on the right is a piece of its own, split where the drawing draws its line (up the right wall 0.51 in out, across at 0.195 in, and in under the rail's head). On its outer face, three round heads in a row, each flush in a hole a ring wider than it: the shaft's end and the two guide pins' (\"A pair of hardened steel precision ground pins is press fitted to the clamp and act as guides.\"), at the places Primary Arms' photo of the LEAP/02's right side gives them: no view of this mount's right side is on file. The shaft across the rail and the pins inside aren't drawn.","The ClickDrive wheel: twenty teeth (counted on the side photo) between the photo's two diameters, its outer face flush with the clamp's left face and as thick as the drawing has it, in a round pocket in the left wall (its clearance assumed), its face dished inside its rim and a socket in its middle (both depths assumed). The set screw in the rear end, in line with the wheel: a hole at the drawing's place and size, its end a little way in (both depths assumed). Not drawn: the engraving and the wheel's gold lettering.","Its metal as drawn: 0.91 cubic inches of 7075 and the steel, 47.6 g, for the maker's 45 g (the rims and the lug left out; the screw holes and the shaft's bore in the body not cut)."],"ledger":["scalarworks-leap-01-micro-157.deck_above_rail","scalarworks-leap-01-micro-157.deck_x","scalarworks-leap-01-micro-157.mount_length","scalarworks-leap-01-micro-157.width","scalarworks-leap-01-micro-157.body_width","scalarworks-leap-01-micro-157.clamp_below_rail"]},"profiles":{"side":{"plane":"xy","origin":"on the rail's top under the ClickDrive wheel's shaft, which lies in the rail slot midway between the two that show","offset":{},"points":[[-0.937,0.095],[-0.937,0.022],[-0.906,0.02],[-0.888,0.002],[-0.88,-0.051],[-0.888,-0.059],[-0.888,-0.103],[-0.878,-0.069],[-0.868,-0.087],[-0.868,-0.112],[-0.888,-0.116],[-0.886,-0.227],[0.679,-0.227],[0.835,0.136],[1.046,0.683],[1.095,0.768],[1.16,0.825],[1.176,0.866],[1.2,0.886],[1.2,0.967],[1.168,0.983],[1.156,1.048],[1.137,1.062],[1.109,1.066],[-0.586,1.062],[-0.6,1.048],[-0.604,0.995],[-0.643,0.953],[-0.841,0.839],[-0.878,0.815],[-0.888,0.797],[-0.896,0.193],[-0.908,0.124]],"features":{"window":[[[0.681,0.679],[0.681,0.724],[0.665,0.772],[0.622,0.823],[0.553,0.856],[-0.116,0.864],[-0.205,0.839],[-0.253,0.815],[-0.432,0.689],[-0.474,0.639],[-0.499,0.578],[-0.503,0.249],[-0.495,0.201],[-0.483,0.172],[-0.448,0.134],[-0.371,0.101],[-0.282,0.101],[-0.276,0.107],[-0.284,0.144],[-0.235,0.168],[-0.227,0.221],[-0.217,0.231],[-0.184,0.227],[-0.162,0.241],[-0.144,0.284],[-0.087,0.276],[-0.055,0.312],[-0.034,0.312],[-0.01,0.292],[0.018,0.292],[0.043,0.312],[0.059,0.312],[0.091,0.276],[0.148,0.284],[0.162,0.266],[0.162,0.249],[0.184,0.227],[0.221,0.227],[0.235,0.217],[0.235,0.176],[0.253,0.154],[0.292,0.136],[0.284,0.116],[0.29,0.101],[0.387,0.101],[0.428,0.122],[0.474,0.164],[0.491,0.193],[0.665,0.622]]]},"scaleRefs":["std.picatinny.slot_pitch"],"inputs":{"std.picatinny.slot_pitch":0.394},"tolerance":0.006,"photo":"references/scalarworks-leap-01-micro-157 e656d3c79e0b (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.57-side-SW0110.jpg: SW0110 alone on a rail section, straight left side, 1200 x 1200)","method":"luminance < 200, inside [288, 425, 830, 757], 2 polygons excluded, closing ×1, largest piece, holes filled; frame from the reviewed holes slot_front, slot_rear (246.6 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.006 in with the extremes kept: 33 points (IoU 0.996 with the full outline); features through the same placement (window: the window through the mount's sides (the white ground through both)) (tools/trace.py)","via":"harvest","note":"The mount's left side, turned to face +x: the deck (its rims' top, with the step at its front end), the leaning front leg, the upright rear leg with its scooped top corner, and the clamp down to its foot under the rail's top; the wheel's outline is taken where it stands in front of the body and its teeth below the foot are left out. The window through both sides is a feature."},"end":{"plane":"zy","origin":"on the rail's top at its middle","offset":{},"points":[[-0.671,-0.005],[-0.662,-0.223],[-0.652,-0.227],[-0.364,-0.23],[-0.356,-0.17],[-0.415,-0.111],[-0.415,-0.091],[-0.317,0.008],[0.315,0.007],[0.417,-0.094],[0.417,-0.109],[0.355,-0.171],[0.361,-0.229],[0.527,-0.231],[0.583,-0.196],[0.64,-0.139],[0.664,-0.094],[0.667,0.217],[0.643,0.276],[0.505,0.414],[0.473,0.479],[0.469,1.048],[0.304,1.048],[0.282,0.985],[0.266,0.965],[-0.251,0.966],[-0.266,0.966],[-0.279,0.979],[-0.304,1.048],[-0.469,1.048],[-0.473,0.477],[-0.494,0.43],[-0.543,0.378],[-0.607,0.314],[-0.637,0.314],[-0.662,0.289]],"features":{"window":[[[0.232,0.851],[0.258,0.847],[0.281,0.835],[0.299,0.817],[0.31,0.794],[0.315,0.768],[0.314,0.263],[0.31,0.237],[0.299,0.214],[0.28,0.196],[0.257,0.185],[0.232,0.181],[-0.233,0.181],[-0.258,0.185],[-0.281,0.197],[-0.299,0.215],[-0.311,0.238],[-0.315,0.263],[-0.315,0.769],[-0.31,0.795],[-0.299,0.817],[-0.281,0.836],[-0.258,0.847],[-0.232,0.851]]]},"scaleRefs":["std.picatinny.top_width","std.picatinny.bevel_gauge_apart","std.picatinny.lower_gauge_below_top","scalarworks-leap-01-micro-157.optical_axis_above_rail"],"inputs":{"scalarworks-leap-01-micro-157.optical_axis_above_rail":1.57,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"tolerance":0.006,"photo":"references/scalarworks-leap-01-micro-157 6359f81fa1be (Scalarworks' technical drawing of SW0110 (scalarworks-SW0110-diagram-A.png): the mount with a T-2 on it, from behind, 1200 x 1200)","method":"luminance < 150, inside [368, 733, 834, 1171], 2 polygons excluded, closing ×2, largest piece, holes filled, opening after the fill 5 px ×1, inset 1 px (half the outline's stroke); frame from the reviewed holes rail_left, rail_right, axis (340.2 px/in, rms 0.001 in over 3 points); origin at the photo's frame; Douglas-Peucker at 0.006 in with the extremes kept: 36 points (IoU 0.994 with the full outline); features through the same placement (window: the window through the mount from end to end, inside its throat (the inner of the two outlines drawn round it)) (tools/trace.py)","via":"harvest","note":"The mount seen from behind, z to the rifle's right: the rims' tops (the T-2's housing on them), the body down to its shoulders, the clamp as wide as the drawing has it, and its jaws round the rail's head to their foot (the left jaw's rounded corner with the wheel's knurl under it: the model mirrors the right half, the maker calling the mount symmetrical). The T-2's foot, down in the deck between the rims, is filled in with the mount (the model is cut at the deck's plane). The window through the mount end to end is a feature."}},"gaps":[{"what":"A view of the deck from straight above, with a scale","need":"where the four screw holes and the lug stand on the floor, and the rims' width: only one oblique from above is on file (Wing Tactical's, its height not said), so neither is drawn"},{"what":"The maker's word on where on the rail it goes","need":"nothing on its page or in its manual says receiver only or not across the receiver's and the handguard's rails; it is started and advised as any sight is"}]},"scalarworks-leap-01-micro-193":{"id":"scalarworks-leap-01-micro-193","name":"LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.93 in","manufacturer":"Scalarworks","sku":"SW0120","url":"https://scalarworks.com/shop/quick-detach-mounts/leap-01/","category":"optic_mount","description":"Scalarworks' quick-detach mount for an Aimpoint Micro T-2 and the dots cut for its footprint, the dot's axis 1.93 in over the rail (\"Optic center height over rail ... SW0120 : 1.93\"\", \"Co-Witness ... SW0120 : Only with 1.93\" PEAK/02\": the maker's own taller backup sights). A frame of 7075 with a window through its sides and its ends, leaning forward over its clamp (\"Forward lean for additional magnifier space\", Primary Arms), clamped by one knurled wheel on the left turned by hand (\"Close clamp by turning ClickDrive wheel as tightly as you can by hand (Do not use tools).\"). 51 g.","weight":"scalarworks-leap-01-micro-193.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":[0,0,0],"note":"Mount frame: on the rail's top under the ClickDrive wheel's shaft, +x forward. It has no cross bolt: the wheel turns a shaft that crosses the rail in a slot (the maker's side photo of this height has it in the slot midway between the two that show), and that slot is the one the build names."},"deck":{"origin":["{.deck_x}","{.deck_above_rail}",0],"note":"On the deck's floor at the footprint's middle, where a dot's base is put (D101): the T-2's foot sits down on it between the deck's two rims."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":"={.clamp_rear}","clamp_front":"={.clamp_front}"},"flips":false,"note":"One clamp, closed by hand: the manual's \"Open clamp no further than internal stops allow.\", \"Hook Leap mount onto rail from ClickDrive side.\" and \"Close clamp by turning ClickDrive wheel as tightly as you can by hand (Do not use tools).\" Its reach along the rail is its foot's two ends about the shaft, as the maker's side photo has them. The page: \"Rails MIL-STD-1913 Picatinny\". Nothing the maker publishes says where on a rifle's rail it goes; its pictures on rifles have it on the receiver's rail."},"deck":{"type":"optic_footprint","role":"deck","anchor":"deck","params":{"pattern":"aimpoint_micro"},"flips":false,"note":"Cut for the Aimpoint Micro T-2's footprint: \"LEAP/01 redefines the standard for mounting your Aimpoint Micro T-2 footprint compatible optic to your AR-15's Picatinny top rail.\" Its list: \"Aimpoint red dot sights Micro T-2, H-2, T-1, H-1, CompM5\", with Holosun's 403, 503, 515 and 530, Primary Arms' Advanced Micro Dot and Microdot, SIG's ROMEO4 and ROMEO5 and Vortex's CROSSFIRE, SPARC II and SPARC SOLAR (the maker's page). Four M3 screws hold the dot: \"Fasteners (4) M3x4mm Nylon patched\"; the manual: \"MAX TORQUE 10 INCH-LBS\"."}},"materials":{"mount":{"label":"Mount","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized_matte","color":"placeholder-black","sku":"SW0120","source":"https://scalarworks.com/shop/quick-detach-mounts/leap-01/"}},"default":"black","note":"The one colour it is sold in: the maker's page offers a height and a package, no colour; MidwayUSA's name for it is \"Matte Black\". Scalarworks: \"Materials 7075-T6 Aluminum / 4140H Steel\", \"Finishes Type III Anodizing / Flash Nitride\": the aluminium hard anodized, and in the maker's studio photos of this height (c3827ed5c44c, 62315e34202e) and Primary Arms' (9aea9c007ed8) a matte charcoal black with no hard highlight, so `anodized_matte`. A black on anodize isn't fitted to a photo: the placeholder black. Not drawn: the engraving."},"hardware":{"label":"Wheel, shaft and set screw","finish":"nitride","recolorable":false,"color":"steel-nitride-black","note":"The steel: the ClickDrive wheel and its shaft, and the set screw in the rear end. Scalarworks: \"4140H Steel\" with \"Flash Nitride\". In the maker's photos the wheel is a glossier black than the body, its face bearing \"SCALARWORKS\" in gold (not drawn). A black on steel isn't fitted to a photo (data/colors/steel.yaml, steel-nitride-black)."}},"components":{"mount":{"label":"Mount","material":"mount"},"hardware":{"label":"Wheel","material":"hardware"}},"geometry":{"model":"scalarworks-leap-01-micro-193.glb","components":{},"approximations":["The body is the two traced outlines' visual hull: the maker's photo of the left side (scaled by the rail's own slots) and its drawing from behind (scaled by the rail drawn in section and the T-2's axis), the drawing's right half mirrored for the left (\"the Leap mount is symmetrical\"). Through it, the window through its sides as the photo has it (its lower edge, hidden behind the wheel, carried on straight at the height it has beside the wheel) and the window through its ends as the drawing has its throat: the four corner posts between are what is left. The photo reads the near face 1.3% larger than the drawing gives (the lens is nearer it than the rail's middle): the outline is drawn as read.","The deck is drawn flat across at its floor, where a dot's base sits (deck_above_rail, the maker's 1.93 in less the T-2's axis over its base; the drawing has the floor 0.02 in lower). The two rims along its sides, which stand 0.078 in over the floor (the drawing) (rim_top_above_rail), and the square lug in its middle aren't drawn: every Micro dot on file is drawn with a flat base as wide as its housing, and they would stand inside it. The four screw holes in the floor aren't drawn either: no view gives their places.","The clamp's channel is the rail's own head in section (MIL-STD-1913's) from the rail's top down to the lower gauge line, the jaws' hooks under that as the drawing has them. The telescoping jaw on the right is a piece of its own, split where the drawing draws its line (up the right wall 0.51 in out, across at 0.195 in, and in under the rail's head). On its outer face, three round heads in a row, each flush in a hole a ring wider than it: the shaft's end and the two guide pins' (\"A pair of hardened steel precision ground pins is press fitted to the clamp and act as guides.\"), at the places Primary Arms' photo of the LEAP/02's right side gives them: no view of this mount's right side is on file. The shaft across the rail and the pins inside aren't drawn.","The ClickDrive wheel: twenty teeth (counted on the side photo) between this height's photo's two diameters, its outer face flush with the clamp's left face and as thick as the drawing has it, in a round pocket in the left wall (its clearance assumed), its face dished inside its rim and a socket in its middle (both depths assumed). The set screw in the rear end, in line with the wheel: a hole at the drawing's place and size, its end a little way in (both depths assumed). Not drawn: the engraving and the wheel's gold lettering.","Its metal as drawn: 1.07 cubic inches of 7075 and the steel, 54.9 g, for the maker's 51 g (the rims and the lug left out; the screw holes and the shaft's bore in the body not cut)."],"ledger":["scalarworks-leap-01-micro-193.deck_above_rail","scalarworks-leap-01-micro-193.deck_x","scalarworks-leap-01-micro-193.mount_length","scalarworks-leap-01-micro-193.width","scalarworks-leap-01-micro-193.body_width","scalarworks-leap-01-micro-193.clamp_below_rail"]},"profiles":{"side":{"plane":"xy","origin":"on the rail's top under the ClickDrive wheel's shaft, which lies in the rail slot midway between the two that show","offset":{},"points":[[-0.937,0.103],[-0.937,0.022],[-0.907,0.016],[-0.888,0.002],[-0.886,-0.243],[0.669,-0.243],[0.761,-0.01],[0.789,0.034],[1.162,0.978],[1.214,1.068],[1.263,1.112],[1.287,1.205],[1.316,1.242],[1.316,1.319],[1.279,1.339],[1.271,1.4],[1.249,1.418],[-0.473,1.418],[-0.483,1.408],[-0.487,1.359],[-0.526,1.309],[-0.83,1.134],[-0.892,1.084],[-0.896,0.225],[-0.913,0.132],[-0.921,0.111]],"features":{"window":[[[0.805,1.027],[0.789,1.096],[0.761,1.14],[0.718,1.179],[0.633,1.211],[0.037,1.219],[-0.084,1.195],[-0.396,0.984],[-0.447,0.938],[-0.483,0.881],[-0.503,0.8],[-0.503,0.261],[-0.495,0.205],[-0.463,0.152],[-0.424,0.122],[-0.404,0.117],[-0.4,0.101],[-0.38,0.113],[-0.291,0.109],[-0.289,0.136],[-0.258,0.146],[-0.232,0.172],[-0.232,0.213],[-0.177,0.223],[-0.145,0.275],[-0.104,0.263],[-0.088,0.267],[-0.056,0.304],[-0.007,0.28],[0.054,0.304],[0.09,0.263],[0.147,0.271],[0.157,0.237],[0.175,0.219],[0.212,0.219],[0.23,0.205],[0.23,0.156],[0.287,0.128],[0.279,0.103],[0.285,0.097],[0.337,0.093],[0.402,0.101],[0.404,0.115],[0.455,0.146],[0.489,0.192],[0.797,0.958]]]},"scaleRefs":["std.picatinny.slot_pitch"],"inputs":{"std.picatinny.slot_pitch":0.394},"tolerance":0.006,"photo":"references/scalarworks-leap-01-micro-193 c3827ed5c44c (Scalarworks, scalarworks-leap-01-quick-detach-mount-1.93-side-SW0120.jpg: SW0120 alone on a rail section, straight left side, 1200 x 1200)","method":"luminance < 200, inside [262, 335, 830, 758], 2 polygons excluded, closing ×1, largest piece, holes filled; frame from the reviewed holes slot_front, slot_rear (246.8 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.006 in with the extremes kept: 26 points (IoU 0.998 with the full outline); features through the same placement (window: the window through the mount's sides (the white ground through both)) (tools/trace.py)","via":"harvest","note":"The mount's left side, turned to face +x: the deck (its rims' top, with the step at its front end), the leaning front leg, the upright rear leg with its scooped top corner, and the clamp down to its foot under the rail's top; the wheel's teeth below the foot are left out. The window through both sides is a feature."},"end":{"plane":"zy","origin":"on the rail's top at its middle","offset":{},"points":[[-0.673,-0.005],[-0.664,-0.223],[-0.654,-0.227],[-0.365,-0.231],[-0.358,-0.17],[-0.416,-0.111],[-0.416,-0.09],[-0.318,0.008],[0.316,0.008],[0.418,-0.094],[0.418,-0.109],[0.356,-0.171],[0.362,-0.23],[0.529,-0.231],[0.561,-0.216],[0.617,-0.163],[0.651,-0.127],[0.666,-0.094],[0.669,0.339],[0.645,0.395],[0.51,0.531],[0.475,0.599],[0.471,1.405],[0.306,1.406],[0.27,1.326],[0.182,1.326],[-0.27,1.326],[-0.305,1.406],[-0.47,1.406],[-0.472,0.614],[-0.499,0.547],[-0.643,0.399],[-0.667,0.355]],"features":{"window":[[[0.233,1.182],[0.259,1.177],[0.282,1.166],[0.3,1.148],[0.312,1.125],[0.316,1.099],[0.315,0.264],[0.311,0.239],[0.299,0.216],[0.281,0.197],[0.258,0.186],[0.232,0.182],[-0.233,0.182],[-0.259,0.186],[-0.282,0.198],[-0.3,0.216],[-0.312,0.239],[-0.316,0.265],[-0.315,1.099],[-0.311,1.125],[-0.3,1.148],[-0.281,1.166],[-0.258,1.178],[-0.233,1.182]]]},"scaleRefs":["std.picatinny.top_width","std.picatinny.bevel_gauge_apart","std.picatinny.lower_gauge_below_top","scalarworks-leap-01-micro-193.optical_axis_above_rail"],"inputs":{"scalarworks-leap-01-micro-193.optical_axis_above_rail":1.93,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"tolerance":0.006,"photo":"references/scalarworks-leap-01-micro-193 c5d15b40764b (Scalarworks' technical drawing of SW0120 (scalarworks-SW0120-diagram-A.png): the mount with a T-2 on it, from behind, 1200 x 1200)","method":"luminance < 150, inside [368, 613, 834, 1171], 2 polygons excluded, closing ×2, largest piece, holes filled, opening after the fill 5 px ×1, inset 1 px (half the outline's stroke); frame from the reviewed holes rail_left, rail_right, axis (339.1 px/in, rms 0.002 in over 3 points); origin at the photo's frame; Douglas-Peucker at 0.006 in with the extremes kept: 33 points (IoU 0.996 with the full outline); features through the same placement (window: the window through the mount from end to end, inside its throat (the inner of the two outlines drawn round it)) (tools/trace.py)","via":"harvest","note":"The mount seen from behind, z to the rifle's right: the rims' tops, the body down to its shoulders, the clamp as wide as the drawing has it, and its jaws round the rail's head to their foot (the left jaw with the wheel's knurl under it: the model mirrors the right half). The T-2's foot, down in the deck between the rims, is left out: the outline's top between the rims is the floor. The window through the mount end to end is a feature."}},"gaps":[{"what":"A view of the deck from straight above, with a scale","need":"where the four screw holes and the lug stand on the floor, and the rims' width: only one oblique from above is on file (Wing Tactical's, filed with the 1.57 in, its height not said), so neither is drawn"},{"what":"The maker's word on where on the rail it goes","need":"nothing on its page or in its manual says receiver only or not across the receiver's and the handguard's rails; it is started and advised as any sight is"}]},"scalarworks-leap-02-micro-226":{"id":"scalarworks-leap-02-micro-226","name":"LEAP/02 Aimpoint Micro T-2 quick-detach mount, 2.26 in","manufacturer":"Scalarworks","sku":"SW0230","url":"https://scalarworks.com/shop/quick-detach-mounts/leap-02/","category":"optic_mount","description":"Scalarworks' quick-detach mount for an Aimpoint Micro T-2 and the dots cut for its footprint, the dot's axis 2.26 in over the rail (\"Optic center height over rail 2.26\"\", \"Co-Witness None (A2 BUIS visible through base)\"): \"LEAP/02 redefines the standard for mounting your Aimpoint Micro T2 footprint optic at 2.26\" height.\" A tall frame of 7075 leaning forward over its clamp, a window through its sides and its ends, clamped by one knurled wheel on the left turned by hand. Black or flat dark earth. 63 g. Out of stock at its maker on 2026-11-03.","weight":"scalarworks-leap-02-micro-226.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":[0,0,0],"note":"Mount frame: on the rail's top under the ClickDrive wheel's shaft, +x forward. It has no cross bolt: the wheel turns a shaft that crosses the rail in a slot (the maker's side photo has it in the slot midway between the two that show), and that slot is the one the build names."},"deck":{"origin":["{.deck_x}","{.deck_above_rail}",0],"note":"On the deck's floor at the footprint's middle, where a dot's base is put (D101): a dot's foot sits down on it between the deck's two rims."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":"={.clamp_rear}","clamp_front":"={.clamp_front}"},"flips":false,"note":"One clamp, closed by hand: \"ClickDrive's low-profile thumbscrew and low-friction telescoping clamp require only the torque from your bare hand to securely attach onto a rail.\" (the maker's page). Its reach along the rail is its foot's two ends about the shaft, as the maker's side photo has them. The page: \"Rails MIL-STD-1913 Picatinny\". Nothing the maker publishes says where on a rifle's rail it goes."},"deck":{"type":"optic_footprint","role":"deck","anchor":"deck","params":{"pattern":"aimpoint_micro"},"flips":false,"note":"Cut for the Aimpoint Micro T-2's footprint: \"LEAP/02 redefines the standard for mounting your Aimpoint Micro T2 footprint optic at 2.26\" height.\" Its list: \"Aimpoint red dot sights Micro T-2, H-2, T-1, H-1, CompM5\", with Holosun's 403, 503, 515 and 530, Primary Arms' Advanced Micro Dot and Microdot, SIG's ROMEO4 and ROMEO5 and Vortex's CROSSFIRE, SPARC II and SPARC SOLAR (the maker's page). \"Fasteners (4) M3x4mm Nylon patched\"."}},"materials":{"mount":{"label":"Mount","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized_matte","color":"placeholder-black","sku":"SW0230","source":"https://scalarworks.com/shop/quick-detach-mounts/leap-02/"},"fde":{"label":"Flat Dark Earth","finish":"anodized_matte","color":"scalarworks-fde","sku":"SW0230-FDE","source":"https://scalarworks.com/shop/quick-detach-mounts/leap-02/"}},"default":"black","note":"Sold in two colours on its maker's page: \"Color — Type III hard anodized finish. Black FDE\", its markup's offers \"LEAP/02 - black\" (SW0230) and \"LEAP/02 - flat-dark-earth\" (SW0230-FDE). \"Finishes Type III Anodizing / Flash Nitride\": the aluminium hard anodized, matte in the maker's studio photos of both (9b13a0aaeb23, e27c207b94de), so `anodized_matte`. Piece by piece on the photos of each colour: the whole body, its rims, its lug and its clamp the one colour; the wheel black in both (the hardware slot). The black isn't fitted to a photo (a black on anodize): the placeholder black. The FDE is the maker's photo of it read under the app's light (data/colors/scalarworks.yaml, scalarworks-fde). Not drawn: the engraving."},"hardware":{"label":"Wheel, shaft and set screw","finish":"nitride","recolorable":false,"color":"steel-nitride-black","note":"The steel: the ClickDrive wheel and its shaft, and the set screw in the rear end. Scalarworks: \"4140H Steel\" with \"Flash Nitride\": black on the black mount and on the FDE one alike (e27c207b94de, ee9fe286117d). A black on steel isn't fitted to a photo (data/colors/steel.yaml, steel-nitride-black)."}},"components":{"mount":{"label":"Mount","material":"mount"},"hardware":{"label":"Wheel","material":"hardware"}},"geometry":{"model":"scalarworks-leap-02-micro-226.glb","components":{},"approximations":["The body is the visual hull of the maker's photo of its left side (scaled by the rail's own slots) and a section across it that is NOT ITS OWN: no view of this mount from an end, or of its width, is on file, so the section is the LEAP/01 1.93 in's (its maker's drawing from behind: the same ClickDrive clamp and wheel, the same footprint under the same rims), its right half mirrored, and lengthened up its straight walls to this mount's deck (end_raise). Through it, the window through its sides as the photo has it (its lower edge, hidden behind the wheel, carried on straight) and the window through its ends, as tall as the frame (\"A2 BUIS visible through base\"; Primary Arms' photo from the front), as wide as the LEAP/01's throat and lengthened with the walls.","The deck is drawn flat across at its floor, where a dot's base sits (deck_above_rail, the maker's 2.26 in less the T-2's axis over its base: no drawing of this mount is on file to read the floor on). The two rims along its sides and the square lug in its middle aren't drawn: every Micro dot on file is drawn with a flat base as wide as its housing, and they would stand inside it. The four screw holes in the floor aren't drawn either: no view gives their places.","The clamp's channel is the rail's own head in section (MIL-STD-1913's) from the rail's top down to the lower gauge line, the jaws' hooks under that as the LEAP/01's drawing has them. The telescoping jaw on the right is a piece of its own, split where the LEAP/01's drawing draws its line. On its outer face, three round heads in a row, each flush in a hole a ring wider than it, as Primary Arms' photo of the right side has them (their places a proportion of the jaw's length in that oblique): the shaft's end and the two guide pins'. The shaft across the rail and the pins inside aren't drawn.","The ClickDrive wheel: twenty teeth (as counted on the LEAP/01's photos) at this mount's photo's diameters, its outer face and thickness the LEAP/01's drawing's, in a round pocket in the left wall (its clearance assumed), its face dished and a socket in its middle (both depths assumed). The set screw in the rear end at the LEAP/01's drawing's place and size (both depths assumed). Round the side window, in each face, three steps (counted on the side photo), each 0.027 in wide (read) and 0.02 in deep (assumed). Not drawn: the engraving, the wheel's gold lettering, and the KICK/09 \"Diving Boards\" the page sells for it.","Its metal as drawn: 1.39 cubic inches of 7075 and the steel, 70.2 g, for the maker's 63 g: 11% over, where the LEAP/01s run 6 to 8% over. The section across is the LEAP/01's, lengthened; the rims, the lug, the screw holes and the shaft's bore aren't cut."],"ledger":["scalarworks-leap-02-micro-226.deck_above_rail","scalarworks-leap-02-micro-226.deck_x","scalarworks-leap-02-micro-226.mount_length","scalarworks-leap-02-micro-226.width","scalarworks-leap-02-micro-226.body_width","scalarworks-leap-02-micro-226.clamp_below_rail"]},"profiles":{"side":{"plane":"xy","origin":"on the rail's top under the ClickDrive wheel's shaft, which lies in the rail slot midway between the two that show","offset":{},"points":[[-0.942,0.14],[-0.942,0.03],[-0.914,0.006],[-0.887,0.003],[-0.887,-0.038],[-0.865,-0.1],[-0.868,-0.117],[-0.887,-0.118],[-0.886,-0.237],[0.887,-0.237],[0.901,0.003],[0.93,0.014],[0.946,0.033],[0.946,0.138],[0.871,0.431],[0.645,1.209],[0.635,1.309],[0.668,1.377],[0.734,1.421],[1.274,1.561],[1.302,1.58],[1.325,1.643],[1.316,1.657],[1.292,1.658],[1.302,1.723],[1.276,1.739],[-0.588,1.732],[-0.601,1.681],[-0.657,0.793],[-0.674,0.76],[-0.71,0.724],[-0.866,0.633],[-0.89,0.609],[-0.897,0.582],[-0.902,0.306]],"features":{"window":[[[0.435,0.609],[0.229,1.327],[0.199,1.395],[0.17,1.426],[0.127,1.448],[0.08,1.456],[-0.186,1.448],[-0.241,1.421],[-0.268,1.395],[-0.295,1.342],[-0.308,1.239],[-0.353,0.424],[-0.343,0.391],[-0.307,0.342],[-0.259,0.312],[-0.209,0.3],[0.203,0.3],[0.24,0.307],[0.28,0.327],[0.314,0.359],[0.409,0.484],[0.432,0.529]]]},"scaleRefs":["std.picatinny.slot_pitch"],"inputs":{"std.picatinny.slot_pitch":0.394},"tolerance":0.006,"photo":"references/scalarworks-leap-02-micro-226 9b13a0aaeb23 (Scalarworks, scalarworks-leap-02-quick-detach-Aimpoint-Micro-T2-mount-side-SW0230-1.jpg: SW0230 alone on a rail section, straight left side, 2000 x 2000)","method":"luminance < 200, inside [440, 410, 1380, 1213], 2 polygons excluded, closing ×1, largest piece, holes filled; frame from the reviewed holes slot_front, slot_rear (398.7 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.006 in with the extremes kept: 35 points (IoU 0.996 with the full outline); features through the same placement (window: the window through the mount's sides (the white ground through both)) (tools/trace.py)","via":"harvest","note":"The mount's left side, turned to face +x: the deck (its rims' top, with the notch at its front tip), the leaning front post, the upright rear post with the step low in its rear face, and the clamp down to its foot under the rail's top; the wheel's teeth below the foot are left out. The window through both sides is a feature."},"end":{"plane":"zy","origin":"on the rail's top at its middle","offset":{},"points":[[-0.673,-0.005],[-0.664,-0.223],[-0.654,-0.227],[-0.365,-0.231],[-0.358,-0.17],[-0.416,-0.111],[-0.416,-0.09],[-0.318,0.008],[0.316,0.008],[0.418,-0.094],[0.418,-0.109],[0.356,-0.171],[0.362,-0.23],[0.529,-0.231],[0.561,-0.216],[0.617,-0.163],[0.651,-0.127],[0.666,-0.094],[0.669,0.339],[0.645,0.395],[0.51,0.531],[0.475,0.599],[0.471,1.405],[0.306,1.406],[0.27,1.326],[0.182,1.326],[-0.27,1.326],[-0.305,1.406],[-0.47,1.406],[-0.472,0.614],[-0.499,0.547],[-0.643,0.399],[-0.667,0.355]],"features":{"window":[[[0.233,1.182],[0.259,1.177],[0.282,1.166],[0.3,1.148],[0.312,1.125],[0.316,1.099],[0.315,0.264],[0.311,0.239],[0.299,0.216],[0.281,0.197],[0.258,0.186],[0.232,0.182],[-0.233,0.182],[-0.259,0.186],[-0.282,0.198],[-0.3,0.216],[-0.312,0.239],[-0.316,0.265],[-0.315,1.099],[-0.311,1.125],[-0.3,1.148],[-0.281,1.166],[-0.258,1.178],[-0.233,1.182]]]},"scaleRefs":["std.picatinny.top_width","std.picatinny.bevel_gauge_apart","std.picatinny.lower_gauge_below_top","scalarworks-leap-01-micro-193.optical_axis_above_rail"],"inputs":{"scalarworks-leap-01-micro-193.optical_axis_above_rail":1.93,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"tolerance":0.006,"photo":"references/scalarworks-leap-01-micro-193 c5d15b40764b (Scalarworks' technical drawing of the LEAP/01 SW0120 (scalarworks-SW0120-diagram-A.png), from behind: the section of the ClickDrive clamp and the frame over it, the only view across a mount of this family on file)","method":"luminance < 150, inside [368, 613, 834, 1171], 2 polygons excluded, closing ×2, largest piece, holes filled, opening after the fill 5 px ×1, inset 1 px (half the outline's stroke); frame from the reviewed holes rail_left, rail_right, axis (339.1 px/in, rms 0.002 in over 3 points); origin at the photo's frame; Douglas-Peucker at 0.006 in with the extremes kept: 33 points (IoU 0.996 with the full outline); features through the same placement (window: the window through the LEAP/01's frame end to end, inside its throat) (tools/trace.py)","via":"harvest","note":"THE LEAP/01 1.93 in's section, from its maker's drawing (no view across this mount is on file): the clamp, the frame's walls and the window through its ends. The model lengthens the walls and the window by end_raise, to this mount's deck."}},"gaps":[{"what":"A view of this mount from an end, or a drawing of it","need":"its own section across (its walls, its window through the ends, the clamp's width) in place of the LEAP/01's, and its deck's floor read on it: none is on the maker's page (no \"diagram\" for SW0230) or a seller's on file"},{"what":"A view of the deck from straight above, with a scale","need":"where the four screw holes and the lug stand on the floor: Primary Arms' oblique from above (4945353b7bdf) shows them, unscaled"},{"what":"The maker's word on where on the rail it goes","need":"nothing on its page says receiver only or not across the receiver's and the handguard's rails; it is started and advised as any sight is"}]},"scalarworks-leap-08-30mm-mount":{"id":"scalarworks-leap-08-30mm-mount","name":"LEAP/08 quick-detach scope mount, 30 mm, 1.57 in","manufacturer":"Scalarworks","sku":"SW0815","url":"https://scalarworks.com/shop/quick-detach-mounts/leap-08/","category":"scope_mount","description":"Scalarworks' quick-detach mount for a 30 mm scope, its rings' axis 1.57 in over the rail (\"Optic center height over rail SW0815 : 1.57\"\"): two rings 24 mm long and 60 mm apart on a beam, the front one ahead of the foot, and two clamps closed by hand, each by a knurled wheel on the left (\"LEAP mounts have no protruding levers, bolts, or knobs\"). 161 g. The scope slides in the rings before their caps are tightened, which sets the eye relief.","weight":"scalarworks-leap-08-30mm-mount.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":[0,0,0],"note":"Mount frame: on the rail's top under the rear clamp's cross shaft, +x forward. It has no cross bolts: each ClickDrive wheel turns on a shaft that crosses the rail in a slot, and the rear one's slot is the one the build names. The front shaft is six slots ahead and a recoil lug under the base is in the slot midway (the maker's drawing draws all three on a rail; its side photo shows them)."},"rings":{"origin":["({.ring_rear_x} + {.ring_front_x}) / 2","{.optical_axis_above_rail}",0],"note":"On the rings' axis midway between the two rings: where a scope's saddle is put at position 0."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":"={.rear_block_rear_x}","clamp_front":"={.front_block_toe_x}","cross_front":"={.clamp_spacing}"},"flips":false,"note":"Two clamps, each closed by hand: the manual's \"Hook Leap mount onto rail from ClickDrive Side and rock onto rail.\" and \"Close clamp by turning ClickDrive wheel clockwise as tightly as you can (Do not use tools!).\" Its reach along the rail is its two clamp blocks' far ends, as the maker's drawing has them: the rear block ends 0.55 in behind the rear shaft (the slot the build names) and the front block's toe is 2.82 in ahead of it, 0.46 in past the front shaft, which is six slots ahead of the rear one. A seam anywhere under that length is under a clamp block or the base between them. The front ring stands wholly ahead of the foot. The page: \"Rails MIL-STD-1913 Picatinny\". Nothing the maker publishes says where on a rifle's rail it goes: it is started and advised as the category's quoted guide has a cantilever mount (as far forward on the receiver as it goes without bridging onto the handguard)."},"rings":{"type":"scope_rings","role":"rings","anchor":"rings","params":{"diameter":"={.ring_bore}","rear_ring":"=({.ring_rear_x} - {.ring_front_x}) / 2","front_ring":"=({.ring_front_x} - {.ring_rear_x}) / 2","ring_length":"={.ring_length}"},"flips":false,"note":"Two rings bored 30 mm (\"Ring diameter 30mm\"), 24 mm long each and 60 mm apart face to face by the maker's drawing (84 mm middle to middle). Six cap screws to a ring (\"Fasteners (12) #8-40 Nylon patched\"; the manual: T15, \"until torque stabilizes at 20inch-lbs\"), the caps closed to no gap on the left (\"NO GAP\" engraved there)."}},"materials":{"body":{"label":"Mount","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized_matte","color":"placeholder-black","sku":"SW0815","source":"https://scalarworks.com/shop/quick-detach-mounts/leap-08/"}},"default":"black","note":"The one colour it is sold in: the page offers a height and a scope, no colour (the \"Dark Earth\" on it is a Nightforce scope sold with the mount). Scalarworks: \"Materials 7075-T6 Al / 4140 CrMo / 17-4 Stainless\", \"Finishes Type III Anodizing / BlackNitride ®\": the aluminium is hard anodized, and in the maker's two studio photos (b723449f6856, 110653a99256) it is a matte charcoal black with no hard highlight, so `anodized_matte`. A black on anodize isn't fitted to a photo: the placeholder black. Piece by piece on those photos and the oblique from below (01bfe847a8c9): the base, the pedestals, the rings' lower halves and the caps are the one matte black; the two wheels, their shafts, the right-hand jaws and the twelve cap screws are a deeper, glossier black (the `hardware` slot). Not drawn: the white engraving (\"NO GAP\", \"20 in-lbs\", \"15 in-lbs\", \"MADE IN USA\", the CAGE code, \"LEVELDRIVE\") and the wheels' gold \"SCALARWORKS\"."},"hardware":{"label":"Wheels, shafts, jaws and screws","finish":"nitride","recolorable":false,"color":"steel-nitride-black","note":"The steel: the two ClickDrive wheels, the shafts they turn on, the moving jaws on the right and the twelve cap screws. Scalarworks: \"4140 CrMo / 17-4 Stainless\" with \"BlackNitride ®\" (which piece is which steel isn't said; the press release as Soldier Systems printed it says \"406 Stainless steel\" where the page says 17-4). In the oblique from below (01bfe847a8c9) the wheels' knurls, the shafts and the jaws' flats are a polished black against the matte base, and in the picture of a cap from above (652257eb3c65) the screw heads are gloss black in matte pockets. A black on steel isn't fitted to a photo (data/colors/steel.yaml, steel-nitride-black)."}},"components":{"body":{"label":"Mount","material":"body"},"hardware":{"label":"Wheels","material":"hardware"}},"geometry":{"model":"scalarworks-leap-08-30mm-mount.glb","components":{},"approximations":["The side outline is the maker's dimensioned drawing of SW0815 (its left side), traced; everything across the mount is read on the maker's one photo from straight behind, scaled by the 30 mm bore, and on one picture of a cap from above. The beam between the rings is taken to be as wide as the pedestal that photo shows (17.6 mm).","The rings are their section as the photo from behind has it (a flat top, 45 degree chamfers, the cap a little wider than the lower half, a chamfer and a round under the tube), 24 mm long, bored 30 mm and closed on the tube: the split is a fine groove, with no gap on either side (the maker's caps close to no gap on the left and leave one on the right). Each ring's end faces are chamfered against its sides by the drawing's millimetre. The bore's grooves and the low lip along each side of the cap's top aren't drawn.","Each cap's screw pockets are plain notches at the drawing's length and floor with the three heads standing on the floor as discs; the pockets' round corners and the heads' Torx sockets aren't drawn. The two holes in each cap's top are cut through to the bore; the two through each pedestal are cut through, in a round-ended recess 6 mm deep each side (read on a three-quarter picture, to 2 mm). The pocket in the base's side under the rear ring is cut 5 mm deep (assumed) and the same on the right, which no view shows. The ten grooves down each side of a ring's lower half are cut 0.3 mm deep (assumed).","Each clamp is a block across the rail at the drawing's length and height: the fixed hooks on the left with the wheel in a round pocket between them, and on the right a steel jaw drawn as everything under the rail's top (where the jaw ends and the block begins there isn't read on a view on file). The blocks' walls are flat-sided: the left wall's rounded face and the block's lightening pockets, which the oblique from below shows, aren't drawn. The rail's place under them is the rail's own head in section (MIL-STD-1913's) from the rail's top down to the lower gauge line, and plain walls as wide apart as the rail's top below that: the photo from behind has the hooks coming in under the rail's lower faces there, by an amount it doesn't give to better than a few hundredths.","The wheels are discs at the drawing's two diameters with twenty teeth (counted on the drawing) and a face dished 0.4 mm (assumed); their thickness is the 4.7 mm that shows from behind. Each shaft is drawn across the rail in its slot, from the wheel to the jaw.","The stepped flutes down the cantilever's lower sides are drawn where the maker's drawing has them (three level lines 0.79 mm apart, each step beginning in a point under the front ring and ending at the front block's face), each step set in 0.4 mm further than the one above it (assumed: no view shows the arm in section), the right side as the left. The round-ended pocket up into the arm's underside under the front ring is drawn where the oblique from below shows it, its place and length proportions of the underside's own length in that picture (to 3 mm), its width and its 5 mm depth assumed. The recoil lug is drawn under the base between the clamps, in the slot midway between the shafts' (the drawing's tab), its width 7 mm by eye on the oblique from below, of the body's metal (the photos show it the base's black; whether it is a part of its own isn't said).","The pockets in the blocks' roofs beside each shaft (in the oblique from below; hidden by the rail when mounted), the LevelDrive's threaded hole under the base and the pin hole at the base's rear end aren't drawn. With them left out the model still holds about a quarter more metal than the maker's 161 g (7.04 oz for 5.68: the flutes and the pocket took 0.06 cubic inches); the rear deck is drawn at the pedestals' width, where the photo from behind has its rear end 25.6 mm across.","The rings' axis is at the maker's stated 1.57 in; its drawing's lines and its side photo both put it 0.02 in higher over the rail. The outline hangs from the axis, so its foot comes that much under the rail's top, where the rail's place is cut out of it."],"ledger":["scalarworks-leap-08-30mm-mount.optical_axis_above_rail","scalarworks-leap-08-30mm-mount.ring_bore","scalarworks-leap-08-30mm-mount.ring_rear_x","scalarworks-leap-08-30mm-mount.ring_front_x","scalarworks-leap-08-30mm-mount.ring_length","scalarworks-leap-08-30mm-mount.ring_gap","scalarworks-leap-08-30mm-mount.clamp_spacing","scalarworks-leap-08-30mm-mount.ring_width","scalarworks-leap-08-30mm-mount.pedestal_width","scalarworks-leap-08-30mm-mount.mount_length"]},"profiles":{"mount":{"plane":"xy","origin":"on the rings' axis above the rear clamp's shaft (the rear wheel's centre is drawn at column 1660.54: 0.02 mm from where this frame puts x = 0); the app lowers it by the axis's height above the rail, to the mount's frame","offset":{"y":"optical_axis_above_rail"},"points":[[-0.628,-1.355],[-0.628,-1.57],[0.509,-1.57],[2.685,-1.57],[2.694,-1.56],[2.901,-1.56],[2.909,-1.568],[2.958,-1.511],[3.026,-1.489],[4.739,-1.282],[4.78,-1.263],[4.808,-1.22],[4.959,-0.828],[4.959,0.678],[4.919,0.713],[4.053,0.713],[4.014,0.674],[4.014,-0.839],[3.984,-0.911],[3.94,-0.958],[3.88,-0.992],[3.846,-0.999],[1.817,-0.999],[1.757,-0.977],[1.691,-0.919],[1.665,-0.873],[1.654,-0.824],[1.654,0.678],[1.614,0.713],[0.748,0.713],[0.709,0.674],[0.709,-0.858],[0.675,-0.941],[0.609,-0.999],[0.545,-1.022],[-0.543,-1.154]],"scaleRefs":["scalarworks-leap-08-30mm-mount.ring_rear_x","scalarworks-leap-08-30mm-mount.ring_front_x"],"inputs":{"scalarworks-leap-08-30mm-mount.optical_axis_above_rail":1.57,"scalarworks-leap-08-30mm-mount.ring_front_x":4.488188976377953,"scalarworks-leap-08-30mm-mount.ring_rear_x":1.1811023622047243},"tolerance":0.006,"photo":"references/scalarworks-leap-08-30mm-mount f533e2d6d088 (Scalarworks' technical drawing of SW0815 (scalarworks-leap-08-1.57in-height-30mm-scope-mount-dimensions-SW0815.png): the left side on a rail, 2000 x 2000)","method":"luminance < 100, inside [320, 740, 1860, 1490], closing ×1, largest piece, holes filled, notches filled in [1472, 1270, 1534, 1372] (disk closing, r 34 px), inset 1 px (half the outline's stroke); frame from the reviewed holes front_ring, rear_ring (265.6 px/in, rms 0.000 in over 2 points); origin at the photo's frame; clipped to y min -{.optical_axis_above_rail} = -1.57; Douglas-Peucker at 0.006 in with the extremes kept: 36 points (IoU 0.999 with the full outline) (tools/trace.py)","via":"harvest","note":"The mount's left side as its maker draws it, turned to face +x, above the rail's top: both rings with their caps, the pedestals, the beam, the cantilever, the rear deck, and the clamp blocks' upper halves with the wheels' in front of them. What is under the rail's top (the hooks, the wheels' lower halves, the lug) is in the ledger, not here. The rail's top is drawn 1.590 in under the axis, where the maker states 1.57: the outline is cut 0.02 in above the drawn line."}},"gaps":[{"what":"A view of the whole mount from above, from below square on, or from the right","need":"none is on the maker's page or anywhere found: the beam's width, the blocks' plan and the right-hand jaws are read on one photo from behind and one oblique"},{"what":"Where the right-hand jaw ends and the block over it begins; the jaws' length","need":"a square view of the mount's right side or underside (a reviewer's photos, once this generation has been reviewed: it was launched 17 Sep 2026)"},{"what":"The metal the model holds over the maker's 161 g (7.04 oz drawn for 5.68)","need":"the pockets in the clamp blocks' roofs and whatever else lightens the base, which only the oblique from below shows and nothing on file measures: a square view of the underside, or a camera fitted to that oblique by its two bores and the wheels' rims. Where the cantilever's flutes and the pocket under it are set in (0.4 mm a step, 5 mm deep) is assumed for the same want"},{"what":"A photo of this mount on a rifle, and the maker's word on where on the rail it goes","need":"neither exists on a page read (the three rifle photos on its page are named for the FUSE/02 bolt-on mount); the manual says how it is clamped and nothing of where"},{"what":"The axis's height: the maker's 1.57 in against 1.59 as its own drawing and side photo have it","need":"a measured review, or the maker's drawing with the height to a tenth of a millimetre"},{"what":"A second seller of SW0815","need":"the maker's own shop is the one on file ($419, its markup's SW0815); Primary Arms' page carries no offer in its markup and no word of which generation it is, MidwayUSA's refuses the reader, GRITR's is SW0810"}]},"sig-alpha-msr-30mm":{"id":"sig-alpha-msr-30mm","name":"ALPHA-MSR scope mount, 30 mm","manufacturer":"SIG SAUER","sku":"SOA20014","category":"scope_mount","description":"SIG's one-piece cantilever scope mount for a 30 mm tube: \"One-piece integral cantilever mount\" with \"M1913 Picatinny style clamps\", the rings' axis 1.535 in above the rail (\"centerline of optic to top of Pic rail\"). The scope slides in its two rings before they are tightened, which sets the eye relief. The mount SIG's TANGO-MSR 1-6x24 is sold in.","weight":"sig-alpha-msr-30mm.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":[0,0,0],"note":"Mount frame: on the rail's top under the rear cross bolt, +x forward. That bolt lies in the slot the build names; the front bolt is five slots ahead."},"rings":{"origin":["({.ring_rear_x} + {.ring_front_x}) / 2","{.optical_axis_above_rail}",0],"note":"On the rings' axis midway between the two rings: where a scope's saddle is put at position 0."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":0,"clamp_front":"={.clamp_bolt_spacing}","cross_front":"={.clamp_bolt_spacing}"},"flips":false,"note":"Two cross bolts five slots apart (1/2 in nuts, 65 in-lb): it is clamped from the rear bolt, in the slot the build names, to the front one. A cantilever mount: the rings stand ahead of the clamp, so the clamp stays on the receiver with the scope forward."},"rings":{"type":"scope_rings","role":"rings","anchor":"rings","params":{"diameter":"={.ring_bore}","rear_ring":"=({.ring_rear_x} - {.ring_front_x}) / 2","front_ring":"=({.ring_front_x} - {.ring_rear_x}) / 2","ring_length":"={.ring_length}"},"flips":false,"note":"Two rings bored 30 mm (the engraving: \"30mm X 1.535\"\"), 3.17 in apart middle to middle and 0.63 long each: 2.54 in between their faces for a scope's saddle. Four cap screws to a ring (T15, 25 in-lb)."}},"materials":{"body":{"label":"Mount","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized_matte","color":"placeholder-black","sku":"SOA20014","source":"https://gritroutdoors.com/sig-sauer-alpha-msr-30mm-black-scope-mount-soa20014"},"coyote":{"label":"Coyote","finish":"anodized_matte","color":"sig-coyote","sku":"SOA20016","source":"https://gritroutdoors.com/sig-sauer-alpha-msr-30mm-scope-mount-soa20016"}},"default":"black","note":"The scope's matte finish (`anodized_matte`: GritrOutdoors' photos of the coyote pair have the mount as matte as the scope). Black is SOA20014; coyote is SOA20016, the mount the coyote TANGO-MSR (SOTM61200) is sold in, its colour matched with the scope's on GritrOutdoors' two photos of the two together. Third Coast Thermal: \"Black or Coyote Brown color options\". Piece by piece on those two photos (2026-10-06): the two rings (caps and lower halves), the arm, the base and the clamp bar are all the one coyote; the cross bolts' heads and their nuts are not (the `hardware` slot). The eight ring-cap screws sit deep in their seats, where what shows is the mount's own brown in shadow: they aren't drawn. The white engraving isn't drawn. GRITR Outdoors' page for SOA20016 alone: \"Color\" \"Coyote Brown\"; its own copy says \"Features an epoxy powder coating that prevents oxidation\" and \"Constructed from a proprietary steel alloy\", where SIG's table has the mount 7075-T6 aluminium: one seller's copy against SIG's, not taken for the finish, which stays the matte anodize the photos show."},"hardware":{"label":"Cross bolts and nuts","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The two cross bolts' round heads on the right and their hex nuts on the left: black steel on the coyote mount as on the black one. GritrOutdoors' photos of the coyote pair have the two nuts black against the coyote clamp bar and the two heads a dark grey against the base; German Sport Guns' photo of the black mount alone (SOA20014) has the nuts a deeper, glossier black than the mount, with the studs' ends bright. GRITR Outdoors' page for the coyote mount: \"Steel 1913 style clamps\"; their coat isn't said on a page on file: drawn as dark steel, the placeholder black (a black on steel isn't fitted to a photo)."}},"components":{"body":{"label":"Mount","material":"body"},"hardware":{"label":"Cross bolts and nuts","material":"hardware"}},"geometry":{"model":"sig-alpha-msr-30mm.glb","components":{},"approximations":["The mount is its own left side view (the photos of the scope in it hide its rings and its bar), placed by the two rings' middles as the scope's side view has them, with its widths from three oblique photos of the mount alone: rings 1.69 in across their side flats and 1.36 from top flat to bottom (they aren't regular octagons: the cap screws stand beside the tube), 0.63 long; the arm a 0.68 in beam; the base 1.16 across with the clamp bar. The side view's own perspective is in the outline (its ends read up to 0.05 in long).","Each ring's four cap screws sit in round seats cut down into the cap's chamfer, with a slot up the chamfer from each and a slot down the lower half under it; the slots are cut 0.05 in deep, which isn't read (their widths and places are). The pockets in the arm's sides are cut 0.20 in deep on a weak reading. The left side's panel carries the part number and the right side's the name: both are drawn as the left's outline.","The base's right side is drawn sloping out from its top face to its full width by halfway down, upright to three quarters, then chamfered in to its foot, as one oblique shows it; under it the rail's place is the rail's own head in section (MIL-STD-1913's, since 2026-10-12) from the rail's top down to the lower gauge line, the base on its right and the clamp bar on its left, and plain walls as wide apart as the rail's top below that, not the jaws' hooks. The clamp bar is its side outline at its measured thickness. Each nut is drawn as a round collar for a third of its length and a hex beyond: where one ends isn't measured. The bolts' heads and nuts are a piece of their own, black on either colour of the mount. The ring feet are drawn as wide as the arm (they read between 0.68 and 0.85).","The rings are drawn bored to the tube they are for, closed on it: the split between a ring's halves is a line in the side outline, with no gap.","Its 5.5 oz is the user's figure, and a retailer says 6."],"ledger":["sig-alpha-msr-30mm.optical_axis_above_rail","sig-alpha-msr-30mm.ring_bore","sig-alpha-msr-30mm.ring_od","sig-alpha-msr-30mm.ring_width","sig-alpha-msr-30mm.ring_length","sig-alpha-msr-30mm.ring_rear_x","sig-alpha-msr-30mm.ring_front_x","sig-alpha-msr-30mm.arm_width","sig-alpha-msr-30mm.base_right_z","sig-alpha-msr-30mm.clamp_bar_outer_z","sig-alpha-msr-30mm.clamp_bolt_spacing","sig-alpha-msr-30mm.mount_length"]},"profiles":{"mount":{"plane":"xy","origin":"on the optical axis above the rear cross bolt (the right-side photo's column 1101.5: the bolt's head shows at 1109, 0.03 in ahead of its axis in that photo's perspective); the app lowers it by the axis's height above the rail","offset":{"y":"optical_axis_above_rail"},"points":[[-0.391,-1.195],[-0.378,-1.216],[-0.37,-1.37],[-0.374,-1.796],[-0.367,-1.803],[0.105,-1.806],[2.429,-1.796],[2.527,-1.674],[2.593,-1.572],[2.671,-1.409],[2.706,-1.268],[2.717,-1.257],[4.542,-1.244],[4.599,-1.215],[4.643,-1.176],[4.967,-0.852],[5.002,-0.792],[5.037,-0.624],[4.991,-0.682],[4.964,-0.69],[4.502,-0.688],[4.322,-0.695],[4.272,-0.654],[4.252,-0.596],[4.259,-0.676],[4.232,-0.732],[4.129,-0.832],[4.046,-0.857],[1.96,-0.858],[1.904,-0.836],[1.836,-0.752],[1.838,-0.6],[1.828,-0.649],[1.773,-0.689],[1.578,-0.684],[1.505,-0.697],[1.401,-0.687],[1.175,-0.695],[1.132,-0.652],[1.121,-0.709],[1.065,-0.795],[0.815,-1.088],[0.735,-1.149],[0.666,-1.166],[0.459,-1.169],[-0.342,-1.163],[-0.385,-1.167]],"scaleRefs":["sig-tango-msr-1-6x24.tube_od","sig-tango-msr-1-6x24.length"],"inputs":{"sig-tango-msr-1-6x24.length":10.4,"sig-tango-msr-1-6x24.tube_od":1.1811023622047243},"tolerance":0.006,"photo":"references/sig-tango-msr-1-6x24 a0aec57f834a (German Sport Guns SOT61000.jpg, right side: the mount under the scope)","method":"luminance < 200, largest piece, holes up to 3000 px filled; what the silhouette has below the turned body (the largest of 11 pieces); scale from sig-tango-msr-1-6x24.tube_od = 1.1811 in, the tube's own width column by column: 276.1 px over columns 1170–1350, 275.5 px over columns 1545–1640, 274.6 px over columns 2025–2060, 273.0 px over columns 2290–2660; a line through them (rms 0.28 px) changes -1.5% from column 1170 to 2660, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1500)/width, the lens's axis taken to meet the image at column 1500; 233.4 px/in there. The axis is the tube's centre line (tilt -0.23°, rms 0.19 px). Lengths then scaled by 1.0125 so that the end faces are sig-tango-msr-1-6x24.length = 10.4 in apart: at the tube's scale they read 10.272 (-1.2%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.160 in over radius 0.591 (rms 0.002), the rear end's rim sags 0.055 in over radius 0.913 (rms 0.005); origin at column 1101.5 of the photo, on the tube's axis; Douglas-Peucker at 0.006 in with the extremes kept: 47 points (IoU 0.993 with the full outline) (tools/trace.py)","via":"harvest","note":"The ALPHA-MSR mount below the rings: their feet, the cantilever arm and the clamp, from the right (the clamp's fixed side, bolt heads)."},"mount_alone":{"plane":"xy","origin":"on the rings' axis above the rear cross bolt, as the outlines of the scope it was photographed with; the app lowers it by the axis's height above the rail, to the mount's frame","offset":{"y":"optical_axis_above_rail"},"points":[[-0.421,-1.315],[-0.415,-1.655],[-0.403,-1.725],[-0.388,-1.735],[-0.274,-1.737],[-0.227,-1.803],[-0.2,-1.816],[-0.081,-1.82],[0.066,-1.811],[0.093,-1.783],[0.11,-1.755],[0.11,-1.744],[0.131,-1.722],[0.136,-1.736],[0.298,-1.732],[0.322,-1.696],[0.321,-1.651],[0.376,-1.649],[1.648,-1.65],[1.655,-1.662],[1.659,-1.711],[1.666,-1.729],[1.723,-1.737],[1.774,-1.734],[1.822,-1.798],[1.862,-1.804],[1.953,-1.797],[2.091,-1.802],[2.108,-1.796],[2.124,-1.78],[2.153,-1.733],[2.332,-1.737],[2.36,-1.732],[2.367,-1.724],[2.368,-1.554],[2.374,-1.554],[2.378,-1.651],[2.387,-1.652],[2.397,-1.642],[2.47,-1.497],[2.499,-1.49],[2.512,-1.477],[2.667,-1.191],[4.471,-1.187],[4.55,-1.146],[4.797,-0.906],[4.914,-0.788],[4.933,-0.759],[4.955,-0.7],[4.992,-0.377],[4.997,-0.286],[4.995,-0.006],[4.981,0.006],[4.989,0.02],[4.992,0.329],[4.958,0.651],[4.949,0.668],[4.922,0.686],[4.679,0.687],[4.362,0.684],[4.345,0.676],[4.326,0.654],[4.327,0.578],[4.346,0.352],[4.343,0.06],[4.348,0.01],[4.338,0.014],[4.335,0.366],[4.328,0.507],[4.319,0.584],[4.311,0.596],[4.301,0.595],[4.283,0.413],[4.275,0.093],[4.281,0.045],[4.281,-0.295],[4.288,-0.453],[4.303,-0.547],[4.314,-0.544],[4.322,-0.515],[4.34,-0.218],[4.341,-0.017],[4.343,-0.005],[4.349,-0.005],[4.35,-0.104],[4.347,-0.374],[4.331,-0.569],[4.321,-0.66],[4.307,-0.685],[4.301,-0.686],[4.298,-0.703],[4.29,-0.708],[4.295,-0.671],[4.277,-0.67],[4.231,-0.723],[4.164,-0.784],[4.122,-0.81],[4.077,-0.819],[3.862,-0.818],[3.86,-0.825],[3.873,-0.829],[3.876,-0.838],[3.896,-0.838],[3.904,-0.846],[3.726,-0.848],[3.705,-0.844],[3.726,-0.842],[3.729,-0.831],[3.703,-0.831],[3.692,-0.839],[3.683,-0.831],[3.665,-0.83],[3.706,-0.828],[3.71,-0.824],[3.703,-0.819],[3.669,-0.82],[3.658,-0.826],[3.629,-0.82],[3.627,-0.826],[3.647,-0.828],[3.64,-0.833],[3.655,-0.843],[3.678,-0.842],[3.669,-0.848],[3.389,-0.85],[3.372,-0.845],[3.281,-0.849],[3.261,-0.837],[3.256,-0.846],[2.791,-0.847],[2.793,-0.834],[2.787,-0.832],[2.791,-0.819],[2.729,-0.819],[2.737,-0.831],[2.78,-0.822],[2.784,-0.832],[2.715,-0.834],[2.723,-0.845],[2.732,-0.839],[2.742,-0.843],[2.718,-0.851],[2.704,-0.851],[2.695,-0.842],[2.681,-0.848],[2.658,-0.843],[2.619,-0.849],[2.614,-0.844],[2.623,-0.839],[2.618,-0.832],[2.601,-0.837],[2.596,-0.829],[2.582,-0.846],[2.562,-0.826],[2.538,-0.836],[2.542,-0.843],[2.565,-0.84],[2.559,-0.846],[2.409,-0.847],[2.412,-0.839],[2.446,-0.841],[2.464,-0.834],[2.448,-0.824],[2.446,-0.83],[2.409,-0.83],[2.389,-0.822],[2.382,-0.826],[2.388,-0.835],[2.375,-0.848],[2.366,-0.848],[2.349,-0.845],[2.347,-0.834],[2.335,-0.834],[2.332,-0.817],[2.322,-0.818],[2.314,-0.841],[2.321,-0.843],[2.322,-0.833],[2.33,-0.831],[2.335,-0.842],[2.342,-0.844],[2.304,-0.848],[2.298,-0.84],[2.279,-0.846],[2.253,-0.818],[2.006,-0.814],[1.944,-0.792],[1.837,-0.689],[1.815,-0.649],[1.807,-0.643],[1.803,-0.647],[1.803,-0.656],[1.797,-0.656],[1.803,-0.67],[1.799,-0.674],[1.786,-0.642],[1.769,-0.395],[1.766,-0.005],[1.774,-0.007],[1.777,-0.356],[1.79,-0.537],[1.8,-0.541],[1.807,-0.525],[1.821,-0.134],[1.817,0.353],[1.81,0.497],[1.798,0.579],[1.787,0.556],[1.782,0.48],[1.774,0.012],[1.763,0.007],[1.766,0.378],[1.781,0.576],[1.78,0.653],[1.75,0.679],[1.733,0.682],[1.189,0.68],[1.16,0.65],[1.129,0.338],[1.131,0.013],[1.137,-0.001],[1.129,-0.013],[1.129,-0.353],[1.154,-0.653],[1.143,-0.698],[1.107,-0.755],[0.838,-1.075],[0.791,-1.116],[0.749,-1.142],[0.726,-1.148],[0.719,-1.144],[0.753,-1.124],[0.734,-1.114],[-0.291,-1.117],[-0.327,-1.134],[-0.332,-1.141],[-0.322,-1.148],[-0.302,-1.142],[-0.293,-1.151],[-0.214,-1.147],[-0.18,-1.153],[-0.358,-1.154],[-0.375,-1.16],[-0.382,-1.178],[-0.355,-1.18],[-0.35,-1.194],[-0.341,-1.182],[-0.335,-1.196],[-0.33,-1.182],[-0.307,-1.182],[-0.287,-1.188],[-0.282,-1.199],[-0.248,-1.196],[-0.248,-1.19],[-0.275,-1.186],[-0.239,-1.182],[-0.235,-1.189],[-0.239,-1.193],[-0.211,-1.195],[-0.207,-1.202],[-0.216,-1.207],[-0.395,-1.205],[-0.408,-1.216],[-0.413,-1.233]],"features":{"screw_pockets":[[[4.888,0.591],[4.862,0.616],[4.78,0.616],[4.755,0.59],[4.756,0.465],[4.72,0.448],[4.707,0.4],[4.73,0.355],[4.77,0.335],[4.877,0.336],[4.917,0.356],[4.939,0.402],[4.924,0.45],[4.889,0.467]],[[4.575,0.589],[4.549,0.614],[4.459,0.613],[4.433,0.587],[4.434,0.463],[4.405,0.445],[4.391,0.397],[4.414,0.352],[4.454,0.333],[4.559,0.333],[4.598,0.354],[4.62,0.399],[4.606,0.447],[4.576,0.464]],[[1.683,0.587],[1.657,0.612],[1.567,0.611],[1.541,0.585],[1.543,0.449],[1.513,0.432],[1.499,0.385],[1.522,0.342],[1.562,0.322],[1.667,0.323],[1.706,0.343],[1.729,0.387],[1.714,0.434],[1.684,0.451]],[[1.366,0.584],[1.34,0.609],[1.249,0.608],[1.224,0.583],[1.225,0.447],[1.196,0.43],[1.182,0.383],[1.205,0.339],[1.245,0.32],[1.35,0.32],[1.389,0.341],[1.411,0.385],[1.397,0.431],[1.367,0.448]]],"lower_pockets":[[[4.906,-0.377],[4.866,-0.338],[4.787,-0.339],[4.747,-0.379],[4.749,-0.56],[4.789,-0.599],[4.868,-0.599],[4.907,-0.559]],[[4.589,-0.38],[4.549,-0.341],[4.464,-0.341],[4.424,-0.381],[4.426,-0.563],[4.466,-0.602],[4.551,-0.601],[4.59,-0.561]],[[1.702,-0.371],[1.663,-0.331],[1.578,-0.332],[1.538,-0.372],[1.54,-0.573],[1.58,-0.612],[1.665,-0.612],[1.704,-0.572]],[[1.385,-0.373],[1.345,-0.334],[1.26,-0.335],[1.221,-0.375],[1.223,-0.576],[1.263,-0.615],[1.348,-0.614],[1.387,-0.574]]],"arm_pockets":[[[4.728,-0.784],[4.326,-0.776],[4.059,-1.081],[4.097,-1.129],[4.465,-1.126],[4.751,-0.84]],[[3.987,-0.932],[2.112,-0.948],[2.084,-0.982],[2.205,-1.134],[3.881,-1.12],[4.01,-0.971]],[[1.782,-0.764],[1.196,-0.769],[0.93,-1.088],[0.964,-1.127],[2.006,-1.119],[2.034,-1.079]]],"split":[[[4.993,0.009],[4.342,0.003],[4.342,-0.008],[4.993,-0.003]],[[1.79,0.007],[1.17,0.002],[1.17,-0.01],[1.79,-0.004]]],"bar":[[[2.361,-1.212],[-0.42,-1.235],[-0.416,-1.751],[0.34,-1.744],[0.34,-1.643],[1.75,-1.631],[1.751,-1.732],[2.365,-1.727]]],"nuts":[[[2.178,-1.324],[1.747,-1.327],[1.751,-1.772],[2.182,-1.768]],[[0.133,-1.336],[-0.314,-1.339],[-0.311,-1.79],[0.137,-1.786]]]},"scaleRefs":["sig-alpha-msr-30mm.ring_rear_x","sig-alpha-msr-30mm.ring_front_x"],"inputs":{"sig-alpha-msr-30mm.ring_front_x":4.645,"sig-alpha-msr-30mm.ring_rear_x":1.477},"tolerance":0.004,"photo":"references/sig-tango-msr-1-6x24 b233f6119cb4 (AR15Discounts SigSaueralpha-msrscopemount30mm...-3.jpg: the ALPHA-MSR alone, straight left side (the part number and '30mm X 1.535 in' engraved on its arm, '65 in - lb' by the nuts), 1920 x 1280)","method":"luminance < 150, largest piece, holes filled; frame from the reviewed holes front_ring, rear_ring (353.1 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.004 in with the extremes kept: 264 points (IoU 0.994 with the full outline); features through the same placement (screw_pockets: each ring cap's two screw pockets as the side sees them: a slot down the chamfer into a wider round seat at the side flat's top; lower_pockets: the two pockets in each ring's lower half, under the cap's screws; arm_pockets: the three recesses in the arm's side: the pocket under the front ring, the long slot, the panel under the rear ring (the part number on this side, SIG SAUER on the right); split: the line between each ring's cap and its lower half; bar: the separate clamp bar on the left, from the line between it and the base down to its foot; relieved between the two nuts; nuts: the two hex nuts on the cross bolts' ends (their outlines' extents; the dark recess round each stud fits a circle at columns 1076 and 1798, rows 983 and 982)) (tools/trace.py)","via":"harvest","note":"Its rings' top flats come out 0.687 in above the axis, where the scope's own photo has 0.6815 (ring_od / 2). The mount as its own left side shows it, turned to face +x: both rings whole (octagonal: their top flats, the chamfer line, the split), the arm with its three recesses, the clamp bar and its nuts, and behind the bar the fixed side's sloped front end."}},"gaps":[{"what":"A view square across the mount, or SIG's own dimensioned drawing","need":"none exists in anything reachable (sigsauer.com refuses readers): every width is read through a camera fitted to an oblique photo of the mount alone"},{"what":"The mount's weight from SIG","need":"SIG's ALPHA-MSR page (sigsauer.com refuses fetches)"},{"what":"Black matched under the app's light (it is the optics' placeholder)","need":"scripts/color-match.mjs against the black product photos"}]},"sig-romeo-msr-gen-2":{"id":"sig-romeo-msr-gen-2","name":"ROMEO-MSR GEN II red dot sight, 2 MOA red dot","manufacturer":"SIG Sauer","url":"https://www.primaryarms.com/sig-sauer-romeo-msr-gen-ii-2-moa-red-dot-sight","category":"optic","description":"SIG Sauer's ROMEO-MSR GEN II, a 1x20 mm red dot with a 2 MOA dot and a rotary brightness dial that holds its CR2032, screwed to its mount by the Micro footprint (Vyce Outdoor: \"The Sig Sauer MSR Gen 2 uses the Aimpoint \"Micro\" footprint\"). Its axis is 0.60 in over its own base: on the see-through riser it is sold on that is \"SIGHT HEIGHT 1.41\" ABSOLUTE CO-WITNESS\" (SIG's sheet). In the box: \"CR2032 Battery, T10 Multi-Tool & Rubber Lens Cover\". The page linked is Primary Arms': SIG's own site isn't read.","weight":"sig-romeo-msr-gen-2.sight_weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"footprint":{"origin":[0,0,0],"note":"Optic frame: origin on the sight's base, its seam with the riser's top, at the footprint's middle (taken to be the base's: sig-romeo-msr-riser-mount.deck_x), +x forward (D101)."},"optical_axis":{"origin":[0,"{.axis_above_base}",0]}},"interfaces":{"footprint":{"type":"optic_footprint","role":"base","anchor":"footprint","params":{"pattern":"aimpoint_micro"},"flips":false,"note":"Vyce Outdoor's review: \"The Sig Sauer MSR Gen 2 uses the Aimpoint \"Micro\" footprint, which is a common pattern used by most micro rifle red dots.\" No sentence of SIG's says so (data/interfaces.yaml, optic_footprint)."},"sight_line":{"type":"optic.sight_line","role":"sight","params":{"magnification":"1x"},"flips":false,"note":"SIG's sheet: \"MAGNIFICATION 1x\", \"Parallax-Free Optical Design\". A red dot: the eye can be anywhere behind it, so it has no eye point of its own."}},"materials":{"body":{"label":"Housing","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized_matte","color":"placeholder-black","sku":"SORMSR101","source":"https://www.primaryarms.com/sig-sauer-romeo-msr-gen-ii-2-moa-red-dot-sight"},"fde":{"label":"Flat Dark Earth","finish":"anodized_matte","color":"sig-fde","sku":"SORMSR111","source":"https://alexandersstore.com/product/sig-sauer-romeo-msr-gen2-1x20mm-fde/"}},"default":"black","note":"Two colours of the same sight: black, SORMSR101 (Primary Arms: \"Color Black\", \"Finish Hardcoat Anodized\"; AR15Discounts: \"Material: Aluminum\"), and flat dark earth, SORMSR111 (Alexander's: \"Manufacturer Part Number SORMSR111\", \"Color Flat Dark Earth\"; Sportsman's Warehouse: \"MPN SORMSR111\", \"Finish FDE\", \"Color Tan\"). On the flat dark earth one only the housing is that colour (the tube, the hood over the top with the elevation turret's seat, the flanks, the windage turret's boss): the riser, the brightness dial, the hoods at the two ends and the two turrets' caps are black, by the one picture of it on file, SIG's rendering as both sellers show it. No page names what the flat dark earth is (an anodize or a sprayed coat): it is drawn in the black one's matte anodize, its colour matched to that rendering under the app's light. Drawn as a satin anodize until 2026-10-06: every photo of the black one has it matte, with no bright line on it. Black is the optics' placeholder (a black on anodize isn't fitted to a photo). Not offered: the green-dot sight (SORMSR102), another product. The windage turret's cap, black inside the housing's boss on the flat dark earth one, isn't a piece of the model (the boss is drawn, at the housing's colour; the cap's own size isn't measured), and the elevation turret's cap is in the housing's outline: both are the housing's colour here."},"hood":{"label":"Hoods at the two ends","finish":"rubber","recolorable":false,"color":"placeholder-polymer-black","note":"The ring at each end of the tube, ahead of the objective and behind the rear window: black on both colours. Vyce Outdoor's review: \"Sig Sauer opted to use rubberized hoods on both ends of the optic\". In Primary Arms' side view they are a finer, duller black than the housing, each parted from it by a groove (the notch in the traced outline, where the model parts them)."},"dial":{"label":"Brightness dial","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","note":"The rotary dial on the right that holds the battery, cap and knurled ring: black on both colours. What it is made of isn't said on a page on file; in the photos it is the housing's matte black, and it is drawn so. Its white numbers aren't drawn."},"lens":{"label":"Lenses","finish":"glass","recolorable":false,"color":"glass-clear","note":"The objective's coating shows red from the front in every photo (SIG's sheet: \"Spectracoat\"): not drawn, the glass is clear."}},"components":{"body":{"label":"Housing","material":"body"},"hood":{"label":"Hoods at the two ends","material":"hood"},"dial":{"label":"Brightness dial","material":"dial"},"lens":{"label":"Lenses","material":"lens"}},"geometry":{"model":"sig-romeo-msr-gen-2.glb","components":{},"approximations":["Built from Primary Arms' straight side view and SIG's published sizes: the tube turned about the optical axis from the outline's underside, the housing along the top at the one width a reviewer's photo from behind gives (no straight end view is on file), and its flat base, the riser's top's length and width, from the seam with the riser up into the tube. Its heights and lengths are the side view's; what lies across it is right to about 0.04 in.","The tube is drawn round and plain: its flutes and the markings aren't drawn. The raised panel on the left flank (the one with SIG SAUER on it) is a block of its face's outline in the side view, its face 0.68 in left of the axis, where the photo from behind and SIG's width put it: the bevel round it and the medallion in it aren't drawn. The housing's flanks are flat and upright where the real ones lean into the tube.","Three pieces, each its own colour: the housing (its flat base with it, which SIG's rendering of the flat dark earth sight has in the housing's tan), the hood at each end of the tube (parted from it where the side outline has its notch, 0.31 in behind the front face and 0.17 ahead of the rear one) and the brightness dial. The turrets' caps aren't pieces: they are drawn in the housing's colour. Until 2026-11-05 the flat base was drawn as the riser's, in its black.","The brightness dial and the windage turret are plain cylinders at their measured diameters, the dial's face 1.08 in right of the axis, SIG's overall width from the left panel's face (until 2026-10-05 it was measured from the round tube's side and stood 0.10 in further out): knurls, the cap's coin slot and the turrets' caps aren't drawn. The windage turret is placed level with the elevation turret, where the quarter views show it.","Its footprint's middle is taken to be its base's: no view shows the screws that hold it to the riser. The lens drawn at both end faces at SIG's 20 mm; its recess and the rear window's own size aren't sourced."],"ledger":["sig-romeo-msr-gen-2.length","sig-romeo-msr-gen-2.width","sig-romeo-msr-gen-2.height","sig-romeo-msr-gen-2.optical_axis_above_rail","sig-romeo-msr-gen-2.window_d","sig-romeo-msr-gen-2.left_panel_reach_z"]},"profiles":{"side":{"plane":"xy","origin":"the riser's middle (x over its rows), the clamp's bottom; offset to the rail's top (the pair's frame, the riser's: the model is moved off it onto the sight's own)","offset":{"y":"clamp_bottom_y"},"points":[[-1.234,1.869],[-1.228,1.225],[-1.089,1.076],[-0.988,1.072],[-0.983,1.023],[-0.961,0.978],[-0.961,0.867],[-0.971,0.867],[-0.984,0.899],[-0.987,0.871],[-0.989,0.465],[-0.963,0.399],[-0.963,0.278],[-0.97,0.269],[-0.975,0.274],[-0.989,0.313],[-0.991,0.106],[-0.965,0.093],[-0.967,0.009],[-0.896,0],[-0.288,0.002],[-0.276,0.035],[-0.256,0.027],[0.297,0.029],[0.313,0.002],[0.375,0],[0.98,0.004],[0.991,0.908],[0.979,1.023],[0.961,1.058],[0.972,1.07],[1.103,1.072],[1.186,1.096],[1.208,1.086],[1.422,1.117],[1.442,1.127],[1.462,1.173],[1.484,1.292],[1.501,1.539],[1.501,1.779],[1.49,1.972],[1.466,2.128],[1.449,2.177],[1.434,2.192],[1.212,2.223],[1.198,2.223],[1.188,2.209],[1.112,2.227],[1.06,2.209],[1.027,2.211],[-0.18,2.443],[-0.247,2.465],[-0.291,2.467],[-0.297,2.474],[-0.375,2.482],[-0.405,2.474],[-0.446,2.484],[-0.787,2.484],[-0.863,2.472],[-1.045,2.253],[-1.062,2.238],[-1.091,2.244],[-1.224,2.103]],"features":{"left_panel":[[[0.99,1.647],[0.974,1.695],[0.931,1.738],[0.834,1.785],[0.6,1.806],[0.21,1.816],[-0.18,1.824],[-0.317,1.836],[-0.405,1.89],[-0.492,1.929],[-0.668,1.945],[-0.843,1.92],[-0.96,1.871],[-1.032,1.828],[-1.038,1.734],[-1.019,1.578],[-0.999,1.5],[-0.96,1.422],[-0.843,1.354],[-0.687,1.321],[-0.531,1.344],[-0.414,1.393],[-0.297,1.432],[0.015,1.446],[0.405,1.461],[0.697,1.477],[0.853,1.496],[0.931,1.539],[0.974,1.598]]]},"scaleRefs":["sig-romeo-msr-gen-2.length","sig-romeo-msr-gen-2.height"],"inputs":{"sig-romeo-msr-gen-2.height":2.4763779527559056,"sig-romeo-msr-gen-2.length":2.7440944881889764},"tolerance":0.006,"photo":"references/sig-romeo-msr-gen-2 befa92096e57 (Primary Arms SORMSR101_02, the sight on its riser, straight left side on white (objective to the left))","method":"luminance < 200, closing ×2, largest piece, holes filled; scale from sig-romeo-msr-gen-2.length = 2.74409 in (x-extent 1403 px → 511.3 px/in) and sig-romeo-msr-gen-2.height = 2.47638 in (y-extent 1274 px → 514.5 px/in), which agree within 0.6%; mean 512.9 px/in; origin at x center, y min of the outline (x over 0.62–0.97 of the height from the top); Douglas-Peucker at 0.006 in with the extremes kept: 63 points (IoU 0.998 with the full outline); features through the same placement (left_panel: the raised flat panel on the left flank: its pointed front end, the band with SIG SAUER, the round swell about the medallion, its rear end (the face's own edge, inside the bevel round it)) (tools/trace.py)","via":"harvest","note":"Its flutes, the SIG medallion, the markings and the clamp plate's own outline are inside the silhouette and aren't in it. The raised panel on the left flank is a feature: the model stands it out of the tube."}},"gaps":[{"what":"A straight view from the front or the rear","need":"A studio end view on a plain ground: its sections across (the housing's flanks, the riser's shoulders, the dial's and the windage turret's sizes) are read through a camera fitted to a reviewer's phone photo"},{"what":"Where the windage turret stands along the sight","need":"A straight right-side or top view: it is placed level with the elevation turret, where the quarter views show it"},{"what":"Its weight with the battery in","need":"SIG's figure is without it, and no page on file gives a CR2032's weight"}]},"sig-romeo-msr-riser-mount":{"id":"sig-romeo-msr-riser-mount","name":"See-Through Riser Mount, 1.41 in absolute co-witness","manufacturer":"SIG Sauer","url":"https://www.primaryarms.com/sig-sauer-romeo-msr-gen-ii-2-moa-red-dot-sight","category":"optic_mount","description":"The riser SIG sells the ROMEO-MSR GEN II on: \"See-Through Riser Mount\" (SIG's sheet; Impact Guns: \"Includes : Romeo MSR Gen II / See-Through Riser Mount / Mounting Hardware / Battery\"). A Micro-footprint dot screws to its top; the ROMEO-MSR on it has its axis 1.41 in over the rail (\"SIGHT HEIGHT 1.41\" ABSOLUTE CO-WITNESS\"), and the window through its legs lets the iron sights be seen under it. The page linked is Primary Arms' for the pair: no page on file sells the riser alone.","weight":"sig-romeo-msr-riser-mount.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":[0,0,0],"note":"Mount frame: origin on the rail's top at the middle of the riser's clamp, +x forward. Where its recoil lug sits along the clamp isn't sourced."},"deck":{"origin":["{.deck_x}","{.deck_above_rail}",0],"note":"On the riser's top at the footprint's middle: where a Micro dot's base is put (D101)."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":"={.mount_length} / 2","clamp_front":"={.mount_length} / 2"},"flips":false,"note":"The riser's length about its middle (the frame's origin)."},"deck":{"type":"optic_footprint","role":"deck","anchor":"deck","params":{"pattern":"aimpoint_micro"},"flips":false,"note":"Cut for the ROMEO-MSR GEN II, which Vyce Outdoor's review calls Micro footprint: \"The Sig Sauer MSR Gen 2 uses the Aimpoint \"Micro\" footprint, which is a common pattern used by most micro rifle red dots.\" No sentence of SIG's says so (data/interfaces.yaml, optic_footprint)."}},"materials":{"mount":{"label":"Riser","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","note":"The see-through riser the sight is sold on, black on both of the sight's colours (GAT Daily: \"a fairly lightweight aluminum design\"; no page names its finish: drawn as the sight's matte anodize). Its clamp plate and cross bolt (a black Torx screw in the photos) aren't drawn."}},"components":{},"geometry":{"model":"sig-romeo-msr-riser-mount.glb","components":{},"approximations":["The side outline below the seam with the sight's base, at the legs' width a reviewer's photo from behind gives (no straight end view is on file), its top at the neck's width with its shoulders sloped out to the legs'. Its top is flat, the plane the sight's base sits on.","The opening through it is a plain slot; the rail's channel under it is the rail's own head in section (MIL-STD-1913's) from the rail's top down to the lower gauge line, and plain walls the rail's width apart below that; its clamp plate, its cross bolt and the four slots in its base aren't drawn.","Centred on the clamp's middle; where its recoil lug sits along the rail isn't sourced. The footprint's middle is taken to be the riser's top's: no view shows the screws."],"ledger":["sig-romeo-msr-riser-mount.deck_above_rail","sig-romeo-msr-riser-mount.mount_length","sig-romeo-msr-riser-mount.clamp_below_rail","sig-romeo-msr-gen-2.riser_width","sig-romeo-msr-gen-2.riser_opening_width"]},"profiles":{},"gaps":[{"what":"A straight view from the front or the rear","need":"A studio end view on a plain ground: the riser's section across (its shoulders, its legs, its opening) is read through a camera fitted to a reviewer's phone photo"},{"what":"A page that sells the riser alone, with its own figures","need":"SIG's riser under a number of its own, with a weight: the weight here is its metal as modelled"}]},"sig-romeo5-gen-ii":{"id":"sig-romeo5-gen-ii","name":"ROMEO5 GEN II 1x20mm Compact Illuminated Dot Sight, 2 MOA red dot","manufacturer":"SIG Sauer","url":"https://www.primaryarms.com/sig-sauer-romeo-5-gen-ii-2-moa-red-dot-sight","category":"optic","description":"SIG Sauer's ROMEO5 GEN II, a 1x20 mm red dot with a 2 MOA dot, top-mounted + and - buttons and a CR2032 under a cap on its right side, screwed to its mount by the Micro footprint (Pew Pew Tactical: \"an Aimpoint T1/T2 micro-style mounting system\"). Its axis is 0.61 in over its own base: on the M1913 I-BEAM it is sold on that is \"Sight to Optical Axis: 1.41”\" (SIG's manual), an absolute co-witness with an AR's iron sights. In the box, by the manual: \"M1913 Low Mount (Select SKU’s); M1913 I-BEAM Mount; Rubber Bikini Lens Cover; Multi-Tool; T20 L-Key; CR2032 Battery\". The page linked is Primary Arms': SIG's own site isn't read.","weight":"sig-romeo5-gen-ii.sight_weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"footprint":{"origin":[0,0,0],"note":"Optic frame: origin on the sight's base, its seam with the I-BEAM's top plate, at the footprint's middle (the four mounting screws' middle in the manual's side view: sig-romeo5-i-beam-mount.deck_x), +x forward (D101)."},"optical_axis":{"origin":[0,"{.axis_above_base}",0]}},"interfaces":{"footprint":{"type":"optic_footprint","role":"base","anchor":"footprint","params":{"pattern":"aimpoint_micro"},"flips":false,"note":"Pew Pew Tactical: \"The standard 5 Gen 2 features a removable mount with a CR2032 battery and an Aimpoint T1/T2 micro-style mounting system.\"; a configurator's guide: \"Both use the Aimpoint Micro footprint\" (data/interfaces.yaml, optic_footprint). No sentence of SIG's says so."},"sight_line":{"type":"optic.sight_line","role":"sight","params":{"magnification":"1x"},"flips":false,"note":"The manual: \"Magnification 1x\", \"unlimited eye-relief and parallax free operation\", \"With infinite eye relief, the sight can be mounted anywhere on the rail; forward or back.\" A red dot: no eye point of its own."}},"materials":{"body":{"label":"Housing","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized_matte","color":"placeholder-black","sku":"SOR5101","source":"https://www.primaryarms.com/sig-sauer-romeo-5-gen-ii-2-moa-red-dot-sight"},"fde":{"label":"Flat Dark Earth","finish":"anodized_matte","color":"sig-fde-romeo5","sku":"SOR5111","source":"https://www.midwestgunworks.com/page/mgwi/prod/sor5111"}},"default":"black","note":"The housing with the bosses its battery cap and windage turret stand in: the one piece that is the colourway's colour. Black, SOR5101 (Primary Arms: \"Color Black\"; the distributor's title at City Arsenal: \"Matte Finish, Black (SOR5101)\"; Scheels: \"Material: Aluminum\"), and Flat Dark Earth, SOR5111 (Midwest Gun Works: \"SIG SAUER ROMEO5 GII 2 MOA RED DOT FDE\", its product code SOR5111; Alexander's: \"Finish/Color: Flat Dark Earth, matte\", MPN SOR5111, UPC 798681716241). In Midwest Gun Works' three photographs of SOR5111 only the housing is that colour: the hood, the rear bezel, the buttons' panel and buttons, the battery cap, the turrets' dials and caps, the I-BEAM mount and its bolt are black, as on the black sight. Every photo has the housing matte with no bright line: drawn as a matte anodize (no page names what either colour is: an anodize or a sprayed coat), and the flat dark earth matched to those photographs under it. Black is the optics' placeholder (a black on anodize isn't fitted to a photo). Not offered: the green-dot sight, SOR5102 (Primary Arms, KYGunCo), the same black housing with another dot: a colour of the reticle, not of anything drawn. The SIG SAUER legend, the roundel (a black medallion on both), ROMEO5 and the serial label aren't drawn."},"ends":{"label":"Front hood and rear bezel","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","note":"The hood round the objective, with its eight notches, and the bezel round the rear window: black on both colourways (Midwest Gun Works' photographs of SOR5111 have them black against the flat dark earth housing). What they are made of isn't said on a page on file: in the photos they are a matte black like the housing's, and they are drawn so."},"knobs":{"label":"Battery cap and turret caps","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","note":"The battery cap on the right, the windage turret's cap and slotted dial on the right, the elevation turret's dial on top: black in every photo of both colourways, the housing's matte (no page names their finish). Their white numbers, the cap's \"10 IN-LBS\" and battery marks, and the R and U arrows aren't drawn."},"controls":{"label":"Buttons and their panel","finish":"rubber","recolorable":false,"color":"placeholder-polymer-black","note":"The + and - buttons (the manual: \"Illumination Controls (+ & –)\", \"press and hold either the (+) or (-) button on the top\") and the panel they stand on in the deck: black on both colourways (Midwest Gun Works' photographs of SOR5111 have the whole panel black in the flat dark earth housing), a duller black than the housing in SIG's view from above. What they are made of isn't said on a page on file: drawn as rubber, as such a keypad is, and said here to be that."},"lens":{"label":"Lenses","finish":"glass","recolorable":false,"color":"glass-clear","note":"The objective's coating shows red-orange from the front in the photos (green on the green-dot sight's): not drawn, the glass is clear."}},"components":{},"geometry":{"model":"sig-romeo5-gen-ii.glb","components":{},"approximations":["Built from SIG's own dimensioned drawings in its manual: the right side view (the outline along the sight) and the front view (the section across it), at the scale their A and B agree on. That scale puts the axis at the manual's 1.41 in and the whole height at 63.1 mm against the 61.5 printed as C: the drawing is what is drawn (ledger, height).","The housing is the side outline across ∩ the front view's outline along, its left half mirrored to the right (the battery cap hides the right flank from the front and nothing else shows it square): symmetric about the axis but for the cap and the windage turret. The front view's outline is brought to the side view's height (0.5%) so the two meet.","The front hood and the rear bezel are turned about the axis from the side outline's edges (both are round in the front view and from above); the hood's eight notches round its face are cut to the side view's length and an assumed depth (ledger, hood_notch_depth).","The battery cap is a cylinder of the side view's circle out to where the front view has its rim, its face a sphere's cap through the front view's two readings of it (cap_face_z at its middle, cap_edge_z at its edge); its coin slot is cut along the sight, as the drawing has it (the cap screws in, so how its slot ends up turned isn't the part's: SIG's right side photo has it upright); the knurl round its rim and the ring round it on the flank (a line in the side view) aren't cut. The windage turret is its boss, cap and slotted dial as three cylinders of the side view's rings, out to the face SIG's view from above has (windage_face_z), each standing out of the one round it by an assumed step (ledger, windage_step); the dial's coin slot is cut to the side view's size. The elevation turret's dial is a piece of its own in a groove in the deck, flush with it, where and as big as the view from above has it, its coin slot across the sight.","The buttons' panel is a pad set into the deck, flush with it, where and as big as SIG's view from above has it, an assumed groove's width in from its outline (ledger, panel_groove); the two buttons stand on it as the side view draws them, as wide as the front view has them; their + and - marks aren't drawn.","Not drawn: the rubber bikini lens cover (in the box, not on the sight in any photo), the M1913 Low Mount sold with some numbers, the lettering and the serial label, the windage and elevation scales, the SIG roundel on the left flank (a black medallion on both colourways), and the sculpting of the flanks: the long raised band and the flutes along the right flank round the turret and the cap (lines in the side view, not in its outline) and the raised panel with the legend on the left, which no view on file shows in section. The flanks are flat, with the front view's chamfers above and below them along the whole housing."],"ledger":["sig-romeo5-gen-ii.length","sig-romeo5-gen-ii.width","sig-romeo5-gen-ii.height","sig-romeo5-gen-ii.axis_above_base","sig-romeo5-gen-ii.window_d"]},"profiles":{"side":{"plane":"xy","origin":"the I-BEAM base's middle (x over its rows; the cross bolt's head is there), the base's foot; offset to the rail's top","offset":{"y":"clamp_bottom_y"},"points":[[-1.251,2.094],[-1.251,1.186],[-1.097,1.032],[-1.003,1.032],[-0.99,1.019],[-0.989,0.898],[-0.814,0.898],[-0.784,0.851],[-0.757,0.826],[-0.632,0.826],[-0.605,0.851],[-0.588,0.882],[-0.572,0.896],[-0.556,0.888],[-0.53,0.863],[-0.523,0.844],[-0.523,0.794],[-0.535,0.753],[-0.552,0.724],[-0.589,0.687],[-0.941,0.493],[-0.976,0.466],[-0.99,0.42],[-0.989,0],[0,0],[0.989,0],[0.99,0.432],[0.983,0.456],[0.955,0.486],[0.582,0.694],[0.552,0.727],[0.533,0.763],[0.523,0.801],[0.526,0.849],[0.533,0.866],[0.553,0.886],[0.577,0.896],[0.607,0.849],[0.635,0.826],[0.757,0.826],[0.784,0.849],[0.817,0.898],[0.989,0.898],[0.99,0.995],[0.997,1.012],[1.018,1.03],[1.161,1.032],[1.493,1.084],[1.493,2.197],[1.25,2.232],[0.929,2.289],[0.915,2.289],[0.898,2.277],[0.888,2.284],[0.773,2.304],[0.76,2.317],[0.761,2.323],[0.749,2.325],[0.608,2.342],[0.594,2.351],[0.572,2.354],[0.567,2.349],[0.484,2.363],[0.462,2.373],[0.433,2.361],[0.304,2.383],[0.223,2.397],[0.204,2.418],[0.194,2.421],[0.177,2.423],[0.172,2.418],[0.163,2.426],[0.158,2.421],[0.139,2.43],[0.132,2.426],[0.11,2.435],[0.103,2.43],[0.096,2.438],[0.089,2.433],[0.079,2.44],[0.074,2.435],[0.067,2.442],[0.053,2.445],[0.048,2.44],[0.038,2.447],[0.034,2.442],[0.026,2.45],[0.019,2.445],[0.012,2.452],[0.005,2.447],[-0.002,2.454],[-0.026,2.454],[-0.101,2.471],[-0.115,2.457],[-0.127,2.457],[-0.239,2.474],[-0.256,2.49],[-0.879,2.49],[-0.914,2.468],[-1.086,2.259]],"features":{"hood":[[[1.25,2.23],[1.497,2.23],[1.497,1.079],[1.25,1.079]]],"rear_bezel":[[[-1.255,2.262],[-1.092,2.262],[-1.092,1.026],[-1.255,1.026]]],"battery_cap":[[[-0.122,2.178],[0.953,2.178],[0.953,1.105],[-0.122,1.105]]],"cap_boss":[[[-0.184,2.221],[0.999,2.221],[0.999,1.062],[-0.184,1.062]]],"windage_boss":[[[-0.905,1.965],[-0.261,1.965],[-0.261,1.318],[-0.905,1.318]]],"windage_cap":[[[-0.833,1.893],[-0.33,1.893],[-0.33,1.39],[-0.833,1.39]]],"windage_dial":[[[-0.733,1.79],[-0.433,1.79],[-0.433,1.491],[-0.733,1.491]]],"skirt":[[[-0.994,1.251],[0.994,1.251],[0.994,1.033],[-0.994,1.033]]],"plate":[[[-0.994,1.033],[0.994,1.033],[0.994,0.894],[-0.994,0.894]]],"web":[[[-0.527,0.894],[0.532,0.894],[0.532,0.66],[-0.527,0.66]]],"base":[[[-0.994,0.669],[0.994,0.669],[0.994,-0.004],[-0.994,-0.004]]],"torx_head":[[[-0.141,0.365],[0.148,0.365],[0.148,0.075],[-0.141,0.075]]],"bolt_boss":[[[-0.326,0.54],[0.33,0.54],[0.33,-0.116],[-0.326,-0.116]]],"screw_rear":[[[-0.802,0.894],[-0.582,0.894],[-0.582,0.825],[-0.802,0.825]]],"screw_front":[[[0.587,0.894],[0.805,0.894],[0.805,0.825],[0.587,0.825]]],"rear_button":[[[-0.108,2.472],[0.213,2.472],[0.213,2.396],[-0.108,2.396]]],"front_button":[[[0.45,2.381],[0.769,2.381],[0.769,2.305],[0.45,2.305]]]},"scaleRefs":["sig-romeo5-gen-ii.length"],"inputs":{"sig-romeo5-gen-ii.length":2.7440944881889764},"tolerance":0.004,"photo":"references/sig-romeo5-gen-ii eb04cdd95d59 (SIG's operator's manual, page 2 at 600 dpi: the dimensioned right side view (A) of the sight on its I-BEAM mount, line art)","method":"luminance < 160, inside [505, 2405, 1712, 3480], 2 polygons excluded, closing ×3, largest piece, holes filled, inset 2 px (half the outline's stroke); scale from sig-romeo5-gen-ii.length = 2.74409 in (x-extent 1146 px → 417.6 px/in); origin at x center, y min of the outline (x over 0.84–0.99 of the height from the top); Douglas-Peucker at 0.004 in with the extremes kept: 100 points (IoU 0.999 with the full outline); checks: height 2.490 ± 0.007; median row width in y [0.02, 0.15] (1.980–1.980) 1.980 ± 0.007; features through the same placement (hood: the front hood: from its seam with the housing to its face, top to bottom; rear_bezel: the rear bezel: the cone from the rear face to where the housing's flanks begin; battery_cap: the battery cap's circle on the right side; cap_boss: the round boss on the housing's right flank that the cap screws into; windage_boss: the windage turret's round boss on the right flank, its outer ring; windage_cap: the windage turret's cap ring; windage_dial: the windage turret's slotted dial in its cap; skirt: the housing's lower band under its round body (ROMEO5 on its left side), down to its seam with the mount's top plate; plate: the I-BEAM mount's top plate, the sight's seat; web: the I-BEAM's web where it is narrowest along the sight, between its two concave flanks; base: the I-BEAM base, from its flat top over the web to its foot; torx_head: the cross bolt's head (T20 Torx) on the base's right side; bolt_boss: the round pad on the base's right side about the cross bolt's head (its circle, which runs on under the base's foot); screw_rear: the rear mounting screw's head (F, T10) under the top plate, seen from the side; screw_front: the front mounting screw's head (F) under the top plate; rear_button: the rear button (-) on the sloped deck; front_button: the front button (+) on the sloped deck) (tools/trace.py)","via":"harvest","note":"SIG's own drawing of the sight on its I-BEAM mount. The two buttons are cut out of the outline and drawn as features (the mounting screws' heads under the top plate are in it: line art can't lose them without opening the web's outline, and the model takes them off by their feature boxes and draws them as screws); the lettering, the serial label and the hood's notches are inside the silhouette."},"end":{"plane":"zy","origin":"the I-BEAM's web across its narrowest rows (the optical axis's column: the objective's rings are centred over it), the base's foot; offset to the rail's top","offset":{"y":"clamp_bottom_y"},"points":[[-0.648,0.417],[-0.648,0.02],[-0.634,0.01],[-0.589,0],[-0.341,0],[-0.34,0.016],[-0.447,0.125],[-0.447,0.142],[-0.434,0.155],[-0.412,0.158],[-0.343,0.222],[-0.169,0.222],[-0.156,0.209],[-0.156,0.14],[-0.14,0.124],[0.141,0.124],[0.155,0.137],[0.155,0.209],[0.168,0.222],[0.342,0.222],[0.439,0.128],[0.436,0.113],[0.379,0.056],[0.38,0.005],[0.39,0],[0.588,0],[0.646,0.013],[0.646,0.424],[0.447,0.48],[0.409,0.501],[0.354,0.554],[0.175,0.554],[0.139,0.563],[0.107,0.593],[0.095,0.62],[0.09,0.655],[0.095,0.765],[0.104,0.82],[0.118,0.833],[0.139,0.821],[0.256,0.821],[0.288,0.849],[0.316,0.888],[0.39,0.891],[0.396,0.897],[0.427,1.018],[0.427,1.035],[0.42,1.042],[0.434,1.056],[0.441,1.076],[0.469,1.101],[0.495,1.108],[0.831,1.103],[0.847,1.14],[0.883,1.293],[0.897,1.381],[0.911,1.541],[0.911,1.565],[0.895,1.579],[0.895,1.684],[0.911,1.699],[0.9,1.863],[0.878,1.995],[0.837,2.155],[0.824,2.163],[0.793,2.158],[0.366,2.158],[0.35,2.181],[0.292,2.478],[-0.293,2.478],[-0.366,2.124],[-0.489,2.001],[-0.636,1.957],[-0.636,1.307],[-0.501,1.27],[-0.459,1.236],[-0.445,1.2],[-0.433,1.059],[-0.418,1.045],[-0.428,1.023],[-0.395,0.897],[-0.384,0.888],[-0.315,0.888],[-0.287,0.846],[-0.257,0.821],[-0.138,0.821],[-0.119,0.836],[-0.103,0.815],[-0.091,0.739],[-0.089,0.674],[-0.094,0.627],[-0.103,0.598],[-0.14,0.563],[-0.176,0.554],[-0.312,0.554],[-0.313,0.491],[-0.326,0.478],[-0.34,0.491],[-0.342,0.538],[-0.362,0.542],[-0.403,0.506],[-0.441,0.482],[-0.63,0.43]],"features":{"battery_cap":[[[0.915,2.167],[0.796,2.167],[0.796,1.104],[0.915,1.104]]],"objective":[[[0.409,2.038],[-0.408,2.038],[-0.408,1.221],[0.409,1.221]]],"web":[[[0.115,0.806],[-0.114,0.806],[-0.114,0.732],[0.115,0.732]]],"screw_right":[[[0.309,0.885],[0.094,0.885],[0.094,0.82],[0.309,0.82]]],"screw_left":[[[-0.093,0.885],[-0.307,0.885],[-0.307,0.82],[-0.093,0.82]]],"buttons":[[[0.122,2.458],[-0.128,2.458],[-0.128,2.386],[0.122,2.386]]],"lug":[[[0.158,0.218],[-0.157,0.218],[-0.157,0.118],[0.158,0.118]]],"jaw":[[[-0.443,0.548],[-0.651,0.548],[-0.651,-0.004],[-0.443,-0.004]]],"channel_roof":[[[0.352,0.223],[-0.35,0.223],[-0.35,0.214],[0.352,0.214]]]},"scaleRefs":["sig-romeo5-gen-ii.width"],"inputs":{"sig-romeo5-gen-ii.width":1.5590551181102363},"tolerance":0.004,"photo":"references/sig-romeo5-gen-ii eb04cdd95d59 (SIG's operator's manual, page 2 at 600 dpi: the dimensioned front view (B, C) of the sight on its I-BEAM mount, line art, mirrored to be seen from the rear)","method":"luminance < 160, inside [2095, 2405, 2785, 3480], closing ×3, largest piece, holes filled, inset 2 px (half the outline's stroke); scale from sig-romeo5-gen-ii.width = 1.55906 in (x-extent 653 px → 418.8 px/in); origin at x center, y min of the outline (x over 0.68–0.7 of the height from the top); Douglas-Peucker at 0.004 in with the extremes kept: 103 points (IoU 0.997 with the full outline); checks: height 2.478 ± 0.007; features through the same placement (battery_cap: the battery cap seen from the front: from its domed face to where it meets its boss, its top to its bottom; objective: the objective's glass, the innermost ring; web: the I-BEAM's web at its narrowest; screw_right: the mounting screws' heads under the top plate on the sight's right; screw_left: the mounting screws' heads under the top plate on the sight's left; buttons: the two buttons on the deck, seen from the front; lug: the block under the roof of the base's rail channel, in the middle: what stands in a rail's slot; jaw: the clamp jaw on the sight's left, from the line that parts it from the base to the base's side; channel_roof: the roof of the base's rail channel, where the rail's top bears) (tools/trace.py)","via":"harvest","note":"SIG's own front view. Its channel and the jaws' hooks are the drawing's: the model's channel is the rail's own head (lib.rail_seat)."}},"gaps":[{"what":"The weight's configuration","need":"A page that says whether the manual's 5.5 oz / 155 g includes the I-BEAM mount and the battery: Bereli's page of the Elite says \"without battery\", and the Tall model's 4 g more for a taller mount says the mount is in it, which is how it is taken"},{"what":"The right flank, square on","need":"A view from the rear or from the front with the cap off, or a plan drawing: the housing is drawn symmetric about the axis under the cap and the windage turret"},{"what":"The finish of the Flat Dark Earth sight","need":"A page that says whether SOR5111's flat dark earth is an anodize or a sprayed coat (Cerakote): it is drawn in the black one's matte anodize, its colour matched to Midwest Gun Works' photograph under it"},{"what":"SIG's own pages (sigsauer.com)","need":"They refuse the project's reader and are left alone; a page the user saves from their own browser could be filed"}]},"sig-romeo5-i-beam-mount":{"id":"sig-romeo5-i-beam-mount","name":"M1913 I-BEAM Mount, 1.41 in absolute co-witness","manufacturer":"SIG Sauer","url":"https://www.primaryarms.com/sig-sauer-romeo-5-gen-ii-2-moa-red-dot-sight","category":"optic_mount","description":"The mount SIG sells the ROMEO5 GEN II on: \"M1913 I-BEAM Mount for situational awareness in all conditions\" (SIG's manual). A Micro-footprint dot screws to its top plate; the ROMEO5 on it has its axis 1.41 in over the rail (\"Sight to Optical Axis: 1.41”\"), an absolute co-witness. Its base clamps to the rail by one cross bolt: \"set the mount on the rail at your preferred eye relief, push the sight forward into the rail lugs and torque the T20 Torx bolt (E) to 65 in-lbs.\" The page linked is Primary Arms' for the pair: no page on file sells the mount alone.","weight":"sig-romeo5-i-beam-mount.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":[0,0,0],"note":"Mount frame: origin on the rail's top at the middle of the I-BEAM's base, +x forward. The cross bolt's head is there in the manual's side view, centred on the roof of the base's rail channel, and the block under that roof (sig-romeo5-gen-ii.lug_width, lug_depth) stands in a slot there."},"deck":{"origin":["{.deck_x}","{.deck_above_rail}",0],"note":"On the top plate at the four screws' middle: where a Micro dot's base is put (D101)."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":"={.mount_length} / 2","clamp_front":"={.mount_length} / 2"},"flips":false,"note":"The I-BEAM base's length about its middle (the frame's origin), where its one cross bolt is."},"deck":{"type":"optic_footprint","role":"deck","anchor":"deck","params":{"pattern":"aimpoint_micro"},"flips":false,"note":"Cut for the ROMEO5 GEN II, which Pew Pew Tactical calls \"an Aimpoint T1/T2 micro-style mounting system\"; Vyce Outdoor: \"The removable I-beam mount on the ROMEO5 Gen 2 is more versatile if you want to change mounts/heights for different guns.\" (data/interfaces.yaml, optic_footprint)."}},"materials":{"mount":{"label":"I-BEAM mount","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","note":"The M1913 I-BEAM mount (the manual: \"M1913 I-BEAM Mount for situational awareness in all conditions\"): its top plate the sight is screwed to, its web, its base and its clamp jaw on the left. Black in every photo; Vyce Outdoor: \"Made of thicker aluminum\". No page names its finish: drawn as the housing's matte anodize."},"hardware":{"label":"Cross bolt and screws","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The T20 Torx cross bolt's head on the base's right side and its round end on the clamp jaw (the manual: \"T20 Torx® Mount Cross Bolt\"), and the four T10 screws' heads under the top plate (\"Mounting Screws (F)\"). Black in every photo; no page says what they are: drawn as blackened steel."}},"components":{},"geometry":{"model":"sig-romeo5-i-beam-mount.glb","components":{},"approximations":["The I-BEAM mount is the outlines' visual hull below the housing: its top plate, its web (as narrow as the front view's narrowest across its whole height) and its base. The mounting screws' heads under the plate are taken off the outline and drawn as four short cylinders, two either side of the web at the two ends of the plate. The base's rail channel is the rail's own head in section (MIL-STD-1913's) from the rail's top down to the lower gauge line, plain walls below it; the block under its roof (the lug) stands in a slot at the base's middle, its length along the rail assumed (ledger, lug_length). The clamp jaw on the left is a piece of its own from jaw_inner_z out, jaw_length long, so its seam shows; the bolt's round end on it and its head (T20, its star recess cut) in a counterbore on the right are drawn; its shank, inside the base and in the slot beside the lug, isn't."],"ledger":["sig-romeo5-i-beam-mount.deck_above_rail","sig-romeo5-i-beam-mount.mount_length","sig-romeo5-i-beam-mount.clamp_below_rail","sig-romeo5-gen-ii.web_width"]},"profiles":{},"gaps":[{"what":"A page that sells the mount alone, with its own figures","need":"SIG's I-BEAM under a number of its own, with a weight: the weight here is its metal as modelled, which the Tall model's 4 g says is more than it is"},{"what":"The M1913 Low Mount","need":"Its height and its outline: the manual says only \"M1913 Low Mount (Select SKU’s)\" and that it takes the I-BEAM's place under the same four screws; Primary Arms' photo SOR5101_03 shows it lying beside the sight (a flat plate with a clamp), with nothing to scale it by. On a rifle it would put the dot at a height no page states, below an AR's co-witness: the part is drawn on the I-BEAM, as SOR5101 is sold and pictured."}]},"sig-tango-msr-1-6x24":{"id":"sig-tango-msr-1-6x24","name":"TANGO-MSR 1-6x24","manufacturer":"SIG SAUER","category":"scope","description":"A 1-6x low-power variable scope (second focal plane, illuminated, MSR BDC6 reticle) on a 30 mm tube. SIG sells it in its one-piece cantilever mount, the ALPHA-MSR, as SOT61000: the scope slides in the mount's rings, which is how its eye relief is set. It does the work of a red dot and a magnifier, and takes the rail space of both. Drawn as photographed: magnification at 1x, the throw lever straight up.","weight":"sig-tango-msr-1-6x24.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"optical_axis":{"origin":[0,0,0],"note":"Scope frame: on the optical axis, +x toward the objective. The origin is the station that stood above the rear cross bolt of the mount it was photographed in."},"tube":{"origin":["{.saddle_x}",0,0],"note":"On the optical axis at the middle of the turret saddle, where the turrets' axes cross it: what a mount's rings are placed by (the saddle midway between them at position 0)."},"objective":{"origin":["{.objective_front_x}",0,0],"note":"The objective's front face, on the axis."},"eyepiece":{"origin":["-{.eyepiece_rear_behind_bolt}",0,0],"note":"The eyepiece's rear face, on the axis. SIG gives the eye relief behind it: 3.93 in at 1x, 3.74 at 6x."}},"interfaces":{"tube":{"type":"scope_rings","role":"tube","anchor":"tube","params":{"diameter":"={.tube_od}","rear_from":"={.tube_rear_from} - {.saddle_x}","rear_to":"={.tube_rear_to} - {.saddle_x}","front_from":"={.tube_front_from} - {.saddle_x}","front_to":"={.tube_front_to} - {.saddle_x}"},"flips":false,"note":"A 30 mm main tube (SIG: \"Maintube Diameter 30mm\"), with 2.2 in of it behind the saddle, back to the magnification ring's housing, and 3.0 in ahead, to the objective's front: a straight tube with no bell. In the ALPHA-MSR the saddle between the two rings is what stops it each way, half an inch from the middle."},"sight_line":{"type":"optic.sight_line","role":"sight","params":{"magnification":"1-6x"},"flips":false,"note":"A variable scope, 1x to 6x (its name on every page), with an eye relief of its own at each end."}},"eye":{"anchor":"eyepiece","relief":["{.eye_relief_high}","{.eye_relief_low}"],"note":"SIG: 3.74 in at 6x, 3.93 in at 1x. Its manual sets it by eye: start as far forward as the scope mounts, then move it back until the view is full."},"materials":{"body":{"label":"Scope","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized_matte","color":"placeholder-black","source":"https://www.german-sport-guns.com/Sig-Sauer-TANGO-MSR-1-6x24-MSR-BDC6-SFP/SOT61000"},"coyote":{"label":"Coyote","finish":"anodized_matte","color":"sig-coyote","source":"https://gritroutdoors.com/sig-sauer-tango-msr-lpvo-coyote-riflescope-sotm61200"}},"default":"black","note":"A matte finish (`anodized_matte`: Sportsman's Warehouse lists the black one \"Finish | Matte\", and GritrOutdoors' photos of the coyote one have no bright line anywhere on it; drawn as a receiver's satin anodize until 2026-10-05, when the user said the coyote was too shiny). Black is SOT61000's, in the black mount (SOA20014); coyote is SOTM61200's, in the coyote mount (SOA20016). The scope and its mount come in one colour. Coyote is matched under the app's light, in that finish, to GritrOutdoors' two photos (a dark brown; a third retailer's small photo reads lighter and pinker). Black is the placeholder the other optics use. Piece by piece (2026-10-06), on GritrOutdoors' two photos of the coyote scope and German Sport Guns' six of the black one: the tube, the saddle, the objective, the eyepiece, the magnification ring, the throw lever, both turret caps and the illumination knob with its numbered ring are all the one colour on each, so the scope is one slot. On the coyote scope the two flip-back lens covers are a lighter, greener tan plastic than the scope's brown, and they hide the objective's front collar and the eyepiece's rear ring in every coyote photo on file: the covers aren't drawn, and those two rings are taken as the scope's coyote. The white markings and the illumination cap's medallion (bright on the black scope; the coyote one's cap has a coin slot and none) aren't drawn."},"lens":{"label":"Lenses","finish":"glass","recolorable":false,"color":"glass-clear"}},"components":{"body":{"label":"Scope","material":"body"},"lens":{"label":"Lenses","material":"lens"}},"geometry":{"model":"sig-tango-msr-1-6x24.glb","components":{},"approximations":["The scope's body is its traced side view turned about the optical axis (German Sport Guns' right side, scaled by the 30 mm tube column by column, since the photo is yawed, and by the published 10.4 in between the end faces). The turret saddle is the ball it is, 0.985 in in radius with a flat under each turret and one beneath: the ball is laid over the saddle in two oblique photos, and the side view's own ends give the same radius.","Under the two rings of the mount it was photographed in, the tube is drawn as the tube it is: the rings show in the traced outline, and belong to the mount.","No end-on or top view exists in anything reachable (two searches), so what stands out sideways is placed through a camera fitted to each oblique photo. The windage turret is the elevation cap again (its face 1.165 in from the axis, where the elevation cap's top is 1.164) and is drawn as that cap's traced outline turned on its side. The illumination knob is its own stack of rings, 1.43 in out, read off one photo (each ring ± 0.04 in); the groove between two of them is drawn 0.03 deep, which isn't read. The two sides add up to 2.60 in where a retailer's unlabelled figure says 70 mm (2.76).","The turret caps are cut as they are counted on the photos (2026-10-05): six flats round the band, a narrow plain rib midway between each two, and knurl between a flat and a rib, four rows of teeth by two columns with a third the flat cuts short. The illumination knob's knurled ring has its twelve patches of knurl, four teeth by three, with a plain land between each two; its teeth are cut as deep as the caps' (0.0125 in), which isn't read on it. Each knob is turned as SIG's photos have it: a cap or a dial turns, and where it stands is where it was left. Not drawn: the bars up each cap's chamfer over its ribs, the illumination knob's numbered dial, the pockets in the ring next to it and the medallion on its face; the eyepiece's rear ring's raised panels, the notch in the objective's front collar; the numbers, the arrows and the engraving.","The magnification ring is cut as the two straight side photos have it (2026-10-13): six knurled panels round it, 60 degrees apart, each two bands of knurl with a groove between, and on either side a smooth flat between each two panels. Assumed: a flat's plane meets the knurl's tops at the edges of the panels beside it (no view gives its depth: 0.04 in at its middle, by that), and the groove between a panel's two bands is as deep as the knurl (0.017 in). A band's three rows of teeth are drawn as three ribs along the ring: the cuts across them, which make each row about eighteen teeth 0.058 in apart, aren't made (some six hundred teeth would take the model past the triangles it may ship with). The smooth panels at the top, under the throw lever, and underneath show in neither side view and are left round, at the traced outline's reach; the outline's lower edge has teeth in it, so what is underneath may not be a smooth panel at all. The line down each smooth panel's middle (about 0.017 in wide) isn't drawn.","The glass sits inside each end: the objective's 0.47 in behind its front face in a bore 1.01 in across, the eye lens 0.30 in inside a rim 1.42 across with a tapered wall down to it. Each of those depths rests on one photo (± 0.06 to 0.08).","Drawn at 1x with the throw lever straight up, as photographed: the lever swings round with the magnification ring. Its base is drawn as wide as its knob. The flip-back lens covers it ships with aren't drawn.","SIG's 18.5 oz is taken as the scope alone: the no-mount model (another reticle) is listed at the same weight."],"ledger":["sig-tango-msr-1-6x24.length","sig-tango-msr-1-6x24.width","sig-tango-msr-1-6x24.tube_od","sig-tango-msr-1-6x24.objective_front_x","sig-tango-msr-1-6x24.eyepiece_rear_behind_bolt","sig-tango-msr-1-6x24.windage_reach","sig-tango-msr-1-6x24.illumination_reach","sig-tango-msr-1-6x24.saddle_radius","sig-tango-msr-1-6x24.saddle_x","sig-tango-msr-1-6x24.cap_flats","sig-tango-msr-1-6x24.cap_flat_width","sig-tango-msr-1-6x24.cap_rib_width","sig-tango-msr-1-6x24.cap_knurl_rows","sig-tango-msr-1-6x24.cap_knurl_columns","sig-tango-msr-1-6x24.cap_knurl_pitch","sig-tango-msr-1-6x24.cap_knurl_depth","sig-tango-msr-1-6x24.illumination_knurl_patches","sig-tango-msr-1-6x24.illumination_knurl_land_width","sig-tango-msr-1-6x24.objective_lens_recess","sig-tango-msr-1-6x24.eyepiece_lens_recess"]},"profiles":{"body":{"plane":"xy","origin":"on the optical axis, at the station that stood above the rear cross bolt of the ALPHA-MSR mount it was photographed in (the right-side photo's column 1101.5: the bolt's head shows at 1109, 0.03 in ahead of its axis in that photo's perspective): the scope's frame","offset":{},"points":[[-3.447,0.227],[-3.447,-0.226],[-3.443,-0.23],[-3.434,-0.522],[-3.417,-0.734],[-3.392,-0.882],[-3.373,-0.901],[-3.318,-0.914],[-3.131,-0.916],[-3.064,-0.908],[-2.992,-0.912],[-2.958,-0.904],[-2.945,-0.913],[-2.928,-0.904],[-2.911,-0.913],[-2.779,-0.909],[-2.775,-0.914],[-2.648,-0.914],[-2.644,-0.91],[-2.474,-0.911],[-2.469,-0.886],[-2.461,-0.886],[-2.448,-0.899],[-2.431,-0.899],[-2.423,-0.89],[-2.414,-0.907],[-2.393,-0.908],[-2.372,-0.886],[-2.363,-0.886],[-2.346,-0.912],[-2.235,-0.904],[-2.206,-0.909],[-2.201,-0.887],[-2.195,-0.89],[-2.195,-0.902],[-2.189,-0.909],[-1.413,-0.909],[-1.408,-0.905],[-1.263,-0.902],[-1.216,-0.911],[-1.173,-0.949],[-1.147,-0.932],[-1.13,-0.932],[-1.105,-0.945],[-1.088,-0.933],[-1.066,-0.933],[-1.045,-0.946],[-1.019,-0.929],[-0.989,-0.946],[-0.959,-0.929],[-0.929,-0.946],[-0.904,-0.93],[-0.869,-0.947],[-0.861,-0.947],[-0.839,-0.93],[-0.831,-0.93],[-0.809,-0.947],[-0.779,-0.93],[-0.745,-0.948],[-0.724,-0.931],[-0.711,-0.931],[-0.685,-0.948],[-0.664,-0.931],[-0.651,-0.931],[-0.634,-0.944],[-0.616,-0.944],[-0.599,-0.932],[-0.586,-0.932],[-0.573,-0.944],[-0.556,-0.945],[-0.535,-0.928],[-0.513,-0.945],[-0.47,-0.932],[-0.453,-0.945],[-0.44,-0.945],[-0.419,-0.928],[-0.393,-0.946],[-0.372,-0.942],[-0.359,-0.929],[-0.333,-0.946],[-0.312,-0.942],[-0.299,-0.929],[-0.29,-0.929],[-0.269,-0.946],[-0.26,-0.946],[-0.239,-0.93],[-0.209,-0.947],[-0.2,-0.947],[-0.178,-0.93],[-0.153,-0.939],[-0.045,-0.833],[-0.022,-0.818],[-0.004,-0.792],[0.06,-0.733],[0.069,-0.716],[0.166,-0.621],[0.204,-0.591],[1.128,-0.587],[1.134,-0.598],[1.134,-0.641],[1.143,-0.658],[1.175,-0.686],[1.401,-0.679],[1.505,-0.688],[1.522,-0.679],[1.561,-0.684],[1.578,-0.676],[1.773,-0.681],[1.799,-0.668],[1.819,-0.649],[1.823,-0.606],[1.843,-0.587],[1.847,-0.591],[2.103,-0.593],[2.108,-0.588],[2.377,-0.59],[2.406,-0.609],[2.456,-0.668],[2.466,-0.666],[2.469,-0.646],[2.482,-0.651],[2.493,-0.67],[2.493,-0.704],[2.534,-0.745],[2.547,-0.754],[2.586,-0.758],[2.593,-0.774],[2.604,-0.78],[2.765,-0.802],[2.843,-0.803],[2.913,-0.812],[3.271,-0.818],[3.284,-0.814],[3.302,-0.819],[3.306,-0.814],[3.485,-0.815],[3.555,-0.807],[3.625,-0.808],[3.735,-0.791],[3.746,-0.785],[3.746,-0.755],[3.752,-0.748],[3.8,-0.744],[3.822,-0.731],[3.958,-0.59],[4.257,-0.587],[4.267,-0.598],[4.281,-0.654],[4.309,-0.682],[4.344,-0.687],[4.349,-0.683],[4.498,-0.683],[4.502,-0.679],[4.771,-0.685],[4.775,-0.681],[4.964,-0.682],[4.991,-0.673],[5.015,-0.65],[5.033,-0.594],[5.053,-0.587],[6.707,-0.592],[6.712,-0.588],[6.92,-0.593],[6.938,-0.584],[7.036,-0.568],[7.074,-0.535],[7.096,-0.501],[7.105,-0.462],[7.118,-0.44],[7.132,-0.392],[7.132,-0.366],[7.145,-0.327],[7.145,-0.297],[7.154,-0.262],[7.158,-0.102],[7.167,-0.093],[7.172,0.028],[7.167,0.033],[7.167,0.093],[7.158,0.102],[7.154,0.263],[7.145,0.297],[7.145,0.328],[7.118,0.441],[7.105,0.462],[7.096,0.502],[7.074,0.536],[7.036,0.569],[6.934,0.591],[6.929,0.587],[6.92,0.591],[6.872,0.587],[6.392,0.592],[6.388,0.588],[5.053,0.587],[5.033,0.594],[5.015,0.65],[4.991,0.674],[4.964,0.682],[4.502,0.679],[4.498,0.683],[4.322,0.688],[4.309,0.684],[4.281,0.656],[4.267,0.6],[4.257,0.589],[3.958,0.59],[3.822,0.732],[3.8,0.745],[3.752,0.75],[3.746,0.756],[3.746,0.786],[3.735,0.793],[3.485,0.815],[3.171,0.82],[3.118,0.811],[2.913,0.812],[2.843,0.803],[2.765,0.804],[2.695,0.791],[2.652,0.791],[2.625,0.778],[2.604,0.778],[2.593,0.772],[2.586,0.757],[2.547,0.753],[2.534,0.744],[2.493,0.703],[2.493,0.669],[2.482,0.65],[2.469,0.645],[2.466,0.665],[2.456,0.667],[2.406,0.609],[2.377,0.59],[1.847,0.591],[1.843,0.587],[1.823,0.606],[1.819,0.649],[1.799,0.669],[1.773,0.681],[1.522,0.678],[1.496,0.686],[1.492,0.682],[1.327,0.678],[1.323,0.683],[1.175,0.687],[1.143,0.659],[1.134,0.642],[1.134,0.6],[1.128,0.589],[0.523,0.591],[0.519,0.586],[0.506,0.591],[0.204,0.591],[0.166,0.621],[0.069,0.718],[0.06,0.735],[-0.153,0.938],[-0.178,0.929],[-0.2,0.946],[-0.209,0.946],[-0.239,0.929],[-0.26,0.946],[-0.269,0.946],[-0.29,0.929],[-0.299,0.929],[-0.312,0.942],[-0.333,0.947],[-0.359,0.93],[-0.372,0.942],[-0.393,0.947],[-0.419,0.93],[-0.44,0.947],[-0.453,0.947],[-0.47,0.934],[-0.513,0.947],[-0.535,0.926],[-0.556,0.943],[-0.573,0.943],[-0.586,0.93],[-0.599,0.93],[-0.616,0.943],[-0.634,0.943],[-0.651,0.93],[-0.664,0.93],[-0.685,0.947],[-0.711,0.93],[-0.724,0.93],[-0.745,0.947],[-0.779,0.93],[-0.809,0.947],[-0.831,0.93],[-0.839,0.93],[-0.861,0.948],[-0.869,0.948],[-0.904,0.931],[-0.929,0.948],[-0.959,0.931],[-0.989,0.948],[-1.019,0.931],[-1.049,0.948],[-1.066,0.931],[-1.088,0.931],[-1.105,0.944],[-1.13,0.931],[-1.147,0.931],[-1.173,0.948],[-1.216,0.91],[-1.263,0.901],[-1.408,0.906],[-1.413,0.91],[-1.571,0.911],[-1.575,0.906],[-2.091,0.912],[-2.095,0.907],[-2.189,0.907],[-2.197,0.886],[-2.204,0.888],[-2.206,0.907],[-2.235,0.903],[-2.316,0.912],[-2.346,0.912],[-2.363,0.887],[-2.372,0.887],[-2.393,0.908],[-2.414,0.908],[-2.423,0.891],[-2.431,0.899],[-2.448,0.899],[-2.461,0.887],[-2.469,0.887],[-2.474,0.912],[-2.61,0.912],[-2.614,0.908],[-2.911,0.913],[-2.928,0.905],[-2.945,0.913],[-2.953,0.905],[-2.992,0.913],[-3.021,0.909],[-3.318,0.914],[-3.373,0.901],[-3.392,0.882],[-3.413,0.772],[-3.434,0.523],[-3.443,0.231]],"scaleRefs":["sig-tango-msr-1-6x24.tube_od","sig-tango-msr-1-6x24.length"],"inputs":{"sig-tango-msr-1-6x24.length":10.4,"sig-tango-msr-1-6x24.tube_od":1.1811023622047243},"tolerance":0.004,"photo":"references/sig-tango-msr-1-6x24 a0aec57f834a (German Sport Guns SOT61000.jpg, right side: the turned body)","method":"luminance < 200, largest piece, holes up to 3000 px filled; the turned body alone: at each column the smaller of the dark run's reach above and below the tube's axis, taken both ways; scale from sig-tango-msr-1-6x24.tube_od = 1.1811 in, the tube's own width column by column: 276.1 px over columns 1170–1350, 275.5 px over columns 1545–1640, 274.6 px over columns 2025–2060, 273.0 px over columns 2290–2660; a line through them (rms 0.28 px) changes -1.5% from column 1170 to 2660, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1500)/width, the lens's axis taken to meet the image at column 1500; 233.4 px/in there. The axis is the tube's centre line (tilt -0.23°, rms 0.19 px). Lengths then scaled by 1.0125 so that the end faces are sig-tango-msr-1-6x24.length = 10.4 in apart: at the tube's scale they read 10.272 (-1.2%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.160 in over radius 0.591 (rms 0.002), the rear end's rim sags 0.055 in over radius 0.913 (rms 0.005); origin at column 1101.5 of the photo, on the tube's axis; Douglas-Peucker at 0.004 in with the extremes kept: 347 points (IoU 0.998 with the full outline) (tools/trace.py)","via":"harvest","note":"Traced from the scope in its ALPHA-MSR mount, so the mount's two rings show on it as two raised stretches (1.14 to 1.83 and 4.27 to 5.03 in): the tube runs on under them, and the model draws it so. The scope's body of revolution: objective, tube, turret saddle, magnification ring, eyepiece. Under the elevation turret and the throw lever it is what shows below the axis; at the rings (octagonal: the model puts octagons there) what shows above."},"turret":{"plane":"xy","origin":"on the optical axis, at the station that stood above the rear cross bolt of the ALPHA-MSR mount it was photographed in (the right-side photo's column 1101.5: the bolt's head shows at 1109, 0.03 in ahead of its axis in that photo's perspective): the scope's frame","offset":{},"points":[[2.545,1.038],[2.545,1.012],[2.554,1.008],[2.554,0.999],[2.545,0.995],[2.545,0.974],[2.554,0.969],[2.554,0.961],[2.545,0.956],[2.545,0.935],[2.554,0.922],[2.545,0.914],[2.545,0.892],[2.593,0.836],[2.593,0.785],[2.599,0.782],[2.625,0.787],[2.652,0.8],[2.695,0.799],[2.765,0.812],[2.843,0.812],[2.913,0.82],[3.118,0.82],[3.171,0.829],[3.485,0.824],[3.555,0.815],[3.625,0.815],[3.691,0.802],[3.717,0.806],[3.743,0.797],[3.746,0.838],[3.798,0.894],[3.798,0.907],[3.781,0.92],[3.798,0.937],[3.785,0.963],[3.798,0.976],[3.798,0.984],[3.785,1.002],[3.803,1.019],[3.781,1.053],[3.748,1.086],[3.608,1.15],[3.332,1.159],[3.328,1.164],[3.319,1.159],[3.302,1.164],[3,1.164],[2.996,1.16],[2.739,1.156],[2.595,1.092],[2.575,1.077]],"scaleRefs":["sig-tango-msr-1-6x24.tube_od","sig-tango-msr-1-6x24.length"],"inputs":{"sig-tango-msr-1-6x24.length":10.4,"sig-tango-msr-1-6x24.tube_od":1.1811023622047243},"tolerance":0.004,"photo":"references/sig-tango-msr-1-6x24 a0aec57f834a (German Sport Guns SOT61000.jpg, right side: the elevation turret)","method":"luminance < 200, largest piece, holes up to 3000 px filled; what the silhouette has above the turned body, in columns 1690–1990; scale from sig-tango-msr-1-6x24.tube_od = 1.1811 in, the tube's own width column by column: 276.1 px over columns 1170–1350, 275.5 px over columns 1545–1640, 274.6 px over columns 2025–2060, 273.0 px over columns 2290–2660; a line through them (rms 0.28 px) changes -1.5% from column 1170 to 2660, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1500)/width, the lens's axis taken to meet the image at column 1500; 233.4 px/in there. The axis is the tube's centre line (tilt -0.23°, rms 0.19 px). Lengths then scaled by 1.0125 so that the end faces are sig-tango-msr-1-6x24.length = 10.4 in apart: at the tube's scale they read 10.272 (-1.2%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.160 in over radius 0.591 (rms 0.002), the rear end's rim sags 0.055 in over radius 0.913 (rms 0.005); origin at column 1101.5 of the photo, on the tube's axis; Douglas-Peucker at 0.004 in with the extremes kept: 52 points (IoU 0.994 with the full outline) (tools/trace.py)","via":"harvest","note":"The capped elevation turret above the saddle, from the side: turned about its own vertical axis."},"lever":{"plane":"xy","origin":"on the optical axis, at the station that stood above the rear cross bolt of the ALPHA-MSR mount it was photographed in (the right-side photo's column 1101.5: the bolt's head shows at 1109, 0.03 in ahead of its axis in that photo's perspective): the scope's frame","offset":{},"points":[[-0.953,1.077],[-0.953,0.946],[-0.946,0.943],[-0.925,0.956],[-0.904,0.939],[-0.895,0.939],[-0.861,0.956],[-0.848,0.943],[-0.831,0.939],[-0.805,0.956],[-0.771,0.939],[-0.745,0.956],[-0.724,0.939],[-0.711,0.939],[-0.685,0.956],[-0.664,0.939],[-0.651,0.939],[-0.634,0.951],[-0.616,0.951],[-0.599,0.939],[-0.586,0.938],[-0.573,0.951],[-0.556,0.951],[-0.543,0.938],[-0.535,0.938],[-0.513,0.955],[-0.47,0.943],[-0.453,0.955],[-0.44,0.955],[-0.415,0.938],[-0.393,0.955],[-0.38,0.955],[-0.355,0.938],[-0.333,0.955],[-0.32,0.955],[-0.299,0.938],[-0.29,0.938],[-0.277,0.951],[-0.26,0.955],[-0.234,0.938],[-0.219,0.948],[-0.219,1.004],[-0.286,1.07],[-0.303,1.079],[-0.578,1.079],[-0.584,1.085],[-0.588,1.192],[-0.55,1.235],[-0.554,1.303],[-0.533,1.324],[-0.546,1.35],[-0.533,1.362],[-0.533,1.375],[-0.546,1.392],[-0.533,1.405],[-0.533,1.413],[-0.546,1.43],[-0.533,1.443],[-0.533,1.452],[-0.546,1.465],[-0.546,1.473],[-0.533,1.482],[-0.533,1.49],[-0.546,1.507],[-0.533,1.52],[-0.533,1.533],[-0.546,1.55],[-0.533,1.563],[-0.533,1.571],[-0.546,1.584],[-0.546,1.592],[-0.537,1.597],[-0.533,1.609],[-0.546,1.622],[-0.546,1.631],[-0.533,1.639],[-0.533,1.652],[-0.546,1.665],[-0.546,1.673],[-0.533,1.682],[-0.533,1.69],[-0.546,1.707],[-0.533,1.72],[-0.533,1.729],[-0.546,1.742],[-0.546,1.75],[-0.533,1.767],[-0.546,1.78],[-0.537,1.805],[-0.554,1.822],[-0.554,1.844],[-0.565,1.859],[-0.586,1.867],[-0.852,1.867],[-0.871,1.844],[-0.871,1.827],[-0.884,1.814],[-0.88,1.784],[-0.889,1.763],[-0.88,1.741],[-0.889,1.733],[-0.889,1.72],[-0.88,1.703],[-0.889,1.682],[-0.876,1.665],[-0.889,1.652],[-0.889,1.644],[-0.876,1.631],[-0.876,1.622],[-0.884,1.618],[-0.889,1.605],[-0.876,1.584],[-0.889,1.567],[-0.876,1.55],[-0.884,1.537],[-0.884,1.52],[-0.876,1.503],[-0.884,1.495],[-0.884,1.482],[-0.871,1.469],[-0.889,1.448],[-0.876,1.431],[-0.876,1.422],[-0.884,1.418],[-0.884,1.401],[-0.871,1.388],[-0.884,1.375],[-0.884,1.363],[-0.871,1.35],[-0.884,1.329],[-0.867,1.307],[-0.867,1.235],[-0.829,1.188],[-0.833,1.167],[-0.829,1.162],[-0.829,1.086],[-0.835,1.079]],"scaleRefs":["sig-tango-msr-1-6x24.tube_od","sig-tango-msr-1-6x24.length"],"inputs":{"sig-tango-msr-1-6x24.length":10.4,"sig-tango-msr-1-6x24.tube_od":1.1811023622047243},"tolerance":0.004,"photo":"references/sig-tango-msr-1-6x24 a0aec57f834a (German Sport Guns SOT61000.jpg, right side: the throw lever)","method":"luminance < 200, largest piece, holes up to 3000 px filled; what the silhouette has above the turned body, in columns 880–1050; scale from sig-tango-msr-1-6x24.tube_od = 1.1811 in, the tube's own width column by column: 276.1 px over columns 1170–1350, 275.5 px over columns 1545–1640, 274.6 px over columns 2025–2060, 273.0 px over columns 2290–2660; a line through them (rms 0.28 px) changes -1.5% from column 1170 to 2660, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1500)/width, the lens's axis taken to meet the image at column 1500; 233.4 px/in there. The axis is the tube's centre line (tilt -0.23°, rms 0.19 px). Lengths then scaled by 1.0125 so that the end faces are sig-tango-msr-1-6x24.length = 10.4 in apart: at the tube's scale they read 10.272 (-1.2%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.160 in over radius 0.591 (rms 0.002), the rear end's rim sags 0.055 in over radius 0.913 (rms 0.005); origin at column 1101.5 of the photo, on the tube's axis; Douglas-Peucker at 0.004 in with the extremes kept: 137 points (IoU 0.992 with the full outline) (tools/trace.py)","via":"harvest","note":"The magnification ring's throw lever, standing straight up at 1x."}},"gaps":[{"what":"A straight top or end view, or SIG's own dimensioned drawing","need":"none exists in anything reachable (two discovery passes; sigsauer.com refuses readers): every width here is read through a camera fitted to an oblique photo, the illumination knob's from one viewpoint (± 0.05 in)"},{"what":"A photo of the scope out of a mount","need":"every side view on file has the ALPHA-MSR's rings over the tube: where the tube begins and ends each side of the saddle is read beside them, and under them it is taken as the plain tube"},{"what":"Black matched under the app's light (it is the optics' placeholder); coyote rests on one retailer's two photos","need":"scripts/color-match.mjs against the black product photos; SIG's own photos of the coyote scope"}]},"silencerco-sparrow-22":{"id":"silencerco-sparrow-22","name":"Sparrow 22","manufacturer":"SilencerCo","sku":"SU75","category":"muzzle_device","description":"A rimfire silencer that threads straight onto a 1/2x28 muzzle: a plain tube with a notched back cap at the mount end and a fluted front cap. Modelled from the outside only.","weight":"silencerco-sparrow-22.weight","nfa":"silencer","cartridge":{"takes":[".22 LR",".17 WSM",".17 HMR",".22 WMR",".22 Hornet","5.7x28mm"],"stated":"22 LR, 17 WSM, 17 HMR, 22 WMR, 22 HORNET, 5.7 X 28 MM (Multi caliber compatibility and rated for full auto fire (22 LR only))","source":"SilencerCo, SPARROW 22 Field Manual, p. 3 (Overview & Product Specs), as Silencer Central hosts it: https://www-wp.silencercentral.com/wp/wp-content/uploads/2025/12/Manual_Sparrow-22.pdf"},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"ffl":true,"anchors":{"thread":{"origin":[0,0,0],"note":"Device frame: on the bore axis at the barrel's shoulder, +x toward the muzzle. The back cap's rear face is taken to bear on the shoulder (the ledger's length says why)."},"front":{"origin":["{.length}",0,0],"note":"The front cap's face: where the build's overall length ends."}},"interfaces":{"thread":{"type":"muzzle_thread","role":"device","anchor":"thread","params":{"thread":"1/2-28","thread_length_made_for":"={.thread_length}"},"flips":false,"note":"SilencerCo's manual: \"mounts on conventional 1/2 X 28 (Class 3A) threads .400 in length\"; its rifle spacer \"is required on threads .600 - .650 in length\"."}},"materials":{"body":{"label":"Outer tube","finish":"phosphate","recolorable":false,"color":"silencerco-sparrow-phosphate","note":"Stainless (SilencerCo's spec sheet: 17-4 & 316 SS); the tube's finish is the phosphate of \"Black Oxide, Magnesium Phosphate (Outer Tube)\" (Capitol Armory, https://www.capitolarmory.com/silencerco-ss-sparrow-22-rimfire-suppressor.html; Silencer Shop: \"Coating Type Black Oxide, Magnesium Phosphate\"): a matte charcoal grey in Primary Arms' three photos (7610478aca44, 09c2b9592403, 09406a0f6baa), lighter and flatter than the caps. One dealer's table says Cerakote; its own description says black oxide. Sold in black only (SU75): the tan and the silver ones in reviewers' photos are the anniversary Sparrow-Ti, another product."},"caps":{"label":"Back and front caps","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The black oxide of \"Black Oxide, Magnesium Phosphate (Outer Tube)\" (Capitol Armory): a smoother, blacker satin than the tube, with a hard highlight on the notches' edges (Primary Arms' photo of the mount end, 09406a0f6baa; the front cap's dished face in 09c2b9592403). A black on polished steel: not fitted to a photo."}},"components":{"body":{"label":"Outer tube","material":"body"},"caps":{"label":"Back and front caps","material":"caps"}},"geometry":{"model":"silencerco-sparrow-22.glb","components":{},"approximations":["The side outline from Primary Arms' photo, revolved: the tube and the front cap's rounded edge. Scaled by the tube's 1.06 in and trimmed to the published 5.08 in about its middle (the photo reads 1.6% long end to end).","The back cap's rim is drawn from its own figures, not from that outline (2026-10-05): a flat rear face 0.85 in across, a 47 degree chamfer to 1.01 in at 0.07 in from the face, a shallow cone to the cap's cylinder at 0.15 in. The outline is cut 0.05 in inside the silhouette's rear tip, and the photo is taken from so near that the rear face is 0.08 in inside it (the lens sees that end from 10.5 degrees off square): the outline's last 0.03 in was the face's rim seen as an arc, and had the flat 0.81 in across.","Eight notches round the back cap, 0.097 in wide, each a ramp: its floor 0.356 in from the axis at the rear face (0.07 in under the rear flat's edge) and running out at the cap's surface 0.25 in ahead of it. The floor is drawn as one flat ramp between those two places; whether it is flat or the arc of a cutter isn't settled, and its corners are drawn square. Which way round the notches stand is free (the silencer stops where its thread tightens): one is drawn on top.","The exit bore at the size the muzzle-end photo shows against the tube (0.27 in), cut back to the middle: the inside isn't modelled.","The two caps are their own pieces (2026-10-06, for their finish): the back cap to its seam 0.445 in from the rear face, the front cap from 0.07 in behind the front face, where its waved seam is drawn straight at the wave's middle. Not drawn: the thread and its ring in the rear face (it is a plain flat), the seams' own grooves and the front one's wave, the front face's eight flutes, its dish and the collar round the bore, the markings.","Seated with its rear face on the barrel's shoulder. SilencerCo makes it for threads .400 in long and requires its spacer on .600 to .650; its manual says nothing about lengths in between. The 22RB's muzzle stands 0.51 in ahead of its shoulder (measured bare on the user's own barrel: thread to 0.39 from the face, then a relief), so whether the Sparrow shoulders on this barrel isn't known: ask SilencerCo before buying."],"ledger":["silencerco-sparrow-22.overall_length","silencerco-sparrow-22.od","silencerco-sparrow-22.bore_d","silencerco-sparrow-22.half_length","silencerco-sparrow-22.rear_face_d","silencerco-sparrow-22.rear_chamfer_x","silencerco-sparrow-22.rear_chamfer_d","silencerco-sparrow-22.rear_break_x","silencerco-sparrow-22.notches","silencerco-sparrow-22.notch_width","silencerco-sparrow-22.notch_length","silencerco-sparrow-22.notch_floor_across","silencerco-sparrow-22.rear_cap_seam_x","silencerco-sparrow-22.front_cap_seam_behind_face"]},"profiles":{"side":{"plane":"xy","origin":"the middle of the silhouette, on the axis: the rear face is half the overall length behind it","offset":{"x":"half_length"},"points":[[-2.54,-0.338],[-2.532,-0.343],[-2.535,-0.392],[-2.529,-0.403],[-2.447,-0.492],[-2.353,-0.522],[-0.904,-0.53],[2.429,-0.53],[2.512,-0.522],[2.524,-0.51],[2.54,-0.472],[2.54,0.464],[2.532,0.494],[2.512,0.522],[2.442,0.527],[-0.217,0.53],[-2.356,0.522],[-2.429,0.503],[-2.527,0.403],[-2.54,0.373]],"scaleRefs":["silencerco-sparrow-22.od"],"inputs":{"silencerco-sparrow-22.od":1.06,"silencerco-sparrow-22.overall_length":5.08},"tolerance":0.004,"photo":"references/silencerco-sparrow-22 7610478aca44 (Primary Arms SU75_01, straight side view on white, 2200 px)","method":"luminance < 200, largest piece, holes filled; scale from silencerco-sparrow-22.od = 1.06 in (y-extent 395 px → 372.6 px/in); origin at x center, y center of the outline; clipped to x min -{.overall_length} / 2 = -2.54, x max {.overall_length} / 2 = 2.54; Douglas-Peucker at 0.004 in with the extremes kept: 20 points (IoU 0.998 with the full outline); scaled by the tube's diameter alone and trimmed to the published length about the middle. At that scale the silhouette is 5.16 in end to end, 1.6% over the published 5.08: put down to the end faces' near rims standing closer to the lens than the axis does, though a longer part would read the same (one article says 5.125); checks: width 5.160 ± 0.008 (tools/trace.py)","via":"harvest","note":"The mount end (the notched back cap) at the rear, the muzzle end at the front. The edges are revolved for the body; the back cap's notches, the seams and the front face's flutes aren't in the outline."}},"gaps":[{"what":"The notches' floors between the rear face and where they run out: flat, or the arc of a cutter; and their corners","need":"a photo straight along a notch from the side, close up (the floor's two ends are measured: 0.356 in from the axis at the rear face, the cap's surface at 0.25 in)"},{"what":"The rear face: the thread's ring (0.60 in across by the mount-end photo) and the thread's depth","need":"SilencerCo's drawing, or a photo straight on at the mount end; the model's rear face is a plain flat, and the barrel's thread stands inside it"},{"what":"The front face: how deep its dish and its eight flutes are, and the collar round the bore","need":"a straight end-on photo of the muzzle end for their plan, and a second view from another side for their depth: one oblique photo (Primary Arms SU75_00) shows where they are and not how deep. Not drawn until then"}]},"slr-sentry-7-gas-block":{"id":"slr-sentry-7-gas-block","name":"Sentry 7 Set Screw Adjustable Gas Block","manufacturer":"SLR Rifleworks","sku":"SA7-SM","url":"https://slrrifleworks.com/sentry-7-set-screw-adjustable-gas-block/","category":"gas_block","description":"SLR Rifleworks' adjustable gas block for a .750 in journal, held by two set screws .400 apart: Melonite-finished 4140 (SA7-SM, the number here). A 15-position metering screw in its front face ('At the front of the gas block is a 15-position adjustment screw', the maker's instruction sheet) opens a port from 0 to 0.125 in; a stamped flat spring on its right side, held by a screw at its rear end, presses a detent plunger on the screw, so each position clicks. It uses the standard gas tube; the tool, the roll pin and the set screws are in the box (US 9,410,756).","weight":"slr-sentry-7-gas-block.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"journal":{"origin":[0,0,0],"note":"On the bore axis at the gas port, +x toward the muzzle. The port is inside and unpublished: it is taken where the standard tube's gas hole lands with its pin in the block's cross hole (port_from_rear, 0.176 in ahead of the rear face)."},"gas_tube":{"origin":[0,"{.tube_hole_above_bore}",0],"x":[-1,0,0],"note":"The tube's hole at the port, +x rearward toward the receiver: 0.674 in above the bore by the patent's rear view (FIG. 4), 0.049 above the Army's .625 for a front sight. No photo on file shows the rear face."}},"interfaces":{"gas_journal":{"type":"ar15.gas_journal","role":"block","anchor":"journal","params":{"journal_od":"={.journal_id}"},"flips":false,"note":"SLR: \"Sentry .750\\\" Set Screw Version - Melonite QPQ Finish .400\\\" Set Screw Spacing\" and \"Note- If you have a barrel with no dimple or one dimple under the gas port either our .400 or .450 set screw spacing blocks will work fine.\" Under a handguard: SLR, \"Works with all SLR Handguards and most others\"; Primary Arms, \"Needs a handguard with at least 1.4\\\" internal diameter to hide underneath\". Its top is 0.812 in above the bore and its flat spring 0.27 in out on the right."},"gas_tube":{"type":"ar15.gas_tube","role":"block","anchor":"gas_tube","params":{},"flips":false,"note":"SLR: \"USES STANDARD GAS TUBE - Tool, roll pin and mounting screws included\"."}},"materials":{"body":{"label":"Gas block","finish":"nitride","recolorable":false,"color":"steel-nitride-black","options":{"melonite":{"label":"Melonite QPQ","finish":"nitride","color":"steel-nitride-black","sku":"SA7-SM","source":"https://slrrifleworks.com/sentry-7-set-screw-adjustable-gas-block/"}},"default":"melonite","note":"One finish for this number. SLR: \"Sentry .750\\\" Set Screw Version - Melonite QPQ Finish\" and \"Melonite finish 4140 Precision machined gas block\"; Primary Arms: \"Melonite-finished 4140 steel construction\". A salt-bath nitride: the app's black nitride, whose colour is a black and isn't fitted to a photo (a black on a sealed finish, CLAUDE.md). The same block in titanium (\"Sentry 7 Set Screw Adjustable Gas Block - Titanium\" on SLR's page; SA7-TI-S on AR15Discounts' list) and with its front screw .450 behind the rear one (\"Sentry 7 Set Screw Adjustable Gas Block - .450\\\"\", in Melonite and titanium) are other products, as are the clamp-on Sentry 7 and the Sentry 6, 8 and 9 for the .625, .875 and .936 journals (SA6-SM, SA8-SM, SA9-SM): none is a colour of this one. The lasered 'S' on the front face isn't drawn."},"hardware":{"label":"Screws","finish":"nitride","recolorable":false,"color":"steel-nitride-black","note":"The metering screw in the front face (SLR: \"Melonite finish 4140 Nexturn Swiss precision metering screw\"), the flat spring's button-head screw and the two set screws: black in the maker's photo and in both of Primary Arms'."},"spring":{"label":"Flat spring","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"SLR: \"Stamped Alloy Flat Spring with 1400deg temper\": bright in all three photos of this number (a satin steel, the app's natural stainless, not matched: a bright metal)."}},"components":{},"geometry":{"model":"slr-sentry-7-gas-block.glb","components":{},"approximations":["Its section is the patent's front view (US 9,410,756, FIG. 3, the number SLR's page prints), scaled by its bore as the journal's .750, run the same along the whole block. The maker's photo of the front face puts the foot 0.553 under the bore (the patent 0.548) and the width's left half 0.016 narrower at the face's broken edge; its top reads 0.036 higher because it is taken from a little above.","Its length (0.856 in) is a fit of that section to Primary Arms' two three-quarter photos' silhouettes, each through an orthographic camera (0.856 and 0.836): equally good fits give up to 0.92, so it is ± 0.04. The published 1.3 oz of 4140 allows 0.80 to 0.87 for this section. The patent's own side view is 0.974 long for this height: the product isn't the embodiment drawn (it has three flutes each side where the patent has a window).","The three flutes each side are grooves round the ring at the right photo's places along the block and its width, from 0.255 above the bore down to 0.38 below it, their bottoms round; how deep they are isn't seen (0.035 in, assumed). The left side's are drawn where the right side's are.","The flat spring is a tapered plate on the patent's flat (0.239 in out on the right), from its screw (0.771 behind the front face, by Primary Arms' right photo) to its rounded tip (0.094), 0.198 tall round its screw and 0.115 at its tip and centred 0.515 above the bore (the maker's photo), 0.025 thick (assumed); where its round about the screw would pass the rear face it ends at the face. The patent's flat is 0.105 tall: the flat is carried as far as the spring reaches and 0.012 more (assumed), so the spring lies on it. The plunger under its tip isn't drawn.","The metering screw is a head of the patent's diameter standing 0.17 in out of the front face (as the maker photographs it; Primary Arms' photos read 0.13 to 0.26 by the way their cameras are fitted, and the screw backs out as it is opened), its end broken to the patent's inner circle and its hex socket the patent's; its thread and its 15 positions aren't drawn. It is on the bore's vertical centre line, 0.481 above the bore.","The gas tube's hole is where the patent's rear view has it (0.674 above the bore, on the centre line), at the standard tube's diameter and the Army's depth past the pin. The roll pin's cross hole is where the right photo has it along the block (0.262 behind the front face; the left photo reads 0.175), at the tube's height (the photos read 0.03 higher, from above) and at the standard pin's diameter. The gas port is where the standard tube's gas hole then lands; the port up from the bore and the metering passage aren't drawn (inside).","The front set screw is 0.252 behind the front face by the left photo (the nearer of the two holes it shows in the bore's floor), the rear one .400 behind it (SLR); their holes are the patent's diameter, the screws 0.15 long from the barrel's surface (assumed), with sockets. Edges broken at 0.008 in (assumed). Not drawn: the lasered 'S', threads, the passages inside."],"ledger":["slr-sentry-7-gas-block.journal_id","slr-sentry-7-gas-block.length","slr-sentry-7-gas-block.height_above_bore","slr-sentry-7-gas-block.foot_below_bore","slr-sentry-7-gas-block.width","slr-sentry-7-gas-block.set_screw_spacing","slr-sentry-7-gas-block.tube_hole_above_bore","slr-sentry-7-gas-block.port_from_rear","slr-sentry-7-gas-block.adjuster_reach"]},"profiles":{"front":{"plane":"zy","origin":"the bore's axis","offset":{},"points":[[-0.452,0.016],[-0.452,0.005],[-0.448,0],[-0.445,-0.06],[-0.431,-0.126],[-0.409,-0.185],[-0.381,-0.237],[-0.346,-0.287],[-0.313,-0.323],[-0.279,-0.352],[-0.233,-0.385],[-0.201,-0.415],[-0.173,-0.452],[-0.124,-0.54],[-0.111,-0.548],[0.108,-0.548],[0.122,-0.541],[0.172,-0.452],[0.192,-0.424],[0.23,-0.386],[0.27,-0.358],[0.307,-0.328],[0.348,-0.284],[0.379,-0.24],[0.405,-0.193],[0.428,-0.133],[0.441,-0.082],[0.447,-0.032],[0.445,0.05],[0.439,0.09],[0.425,0.142],[0.408,0.185],[0.374,0.247],[0.344,0.287],[0.34,0.296],[0.337,0.297],[0.305,0.329],[0.29,0.347],[0.266,0.383],[0.259,0.398],[0.259,0.407],[0.251,0.415],[0.239,0.452],[0.239,0.557],[0.226,0.558],[0.216,0.566],[0.183,0.6],[0.174,0.614],[0.166,0.63],[0.158,0.657],[0.157,0.705],[0.154,0.717],[0.145,0.739],[0.132,0.756],[0.107,0.778],[0.071,0.798],[0.036,0.809],[0.014,0.812],[-0.037,0.809],[-0.075,0.797],[-0.115,0.772],[-0.132,0.758],[-0.147,0.736],[-0.158,0.704],[-0.158,0.579],[-0.161,0.546],[-0.179,0.48],[-0.201,0.437],[-0.229,0.398],[-0.341,0.293],[-0.389,0.224],[-0.412,0.178],[-0.429,0.131],[-0.443,0.07],[-0.448,0.02]],"scaleRefs":["slr-sentry-7-gas-block.journal_id"],"inputs":{"slr-sentry-7-gas-block.journal_id":0.75},"tolerance":0.002,"photo":"references/slr-sentry-7-gas-block e33823945e77 (US 9,410,756, sheet 3, FIG. 3: the block from its front, orthographic, 2560 x 3300 (the patent office's PDF))","method":"luminance < 200, inside [700, 1850, 1700, 2560], 2 boxes excluded, closing ×5, largest piece, holes filled, opening after the fill 7 px ×1, inset 2 px (half the outline's stroke); frame from the reviewed holes top, under, right, left (648.3 px/in, rms 0.000 in over 4 points); origin at the photo's frame; Douglas-Peucker at 0.002 in with the extremes kept: 75 points (IoU 0.995 with the full outline); the frame is the bore's circle, the journal's .750: the patent is a utility patent drawn without a scale, and its other proportions are held to the maker's photo of the front face (the ledger's photo readings) (tools/trace.py)","via":"harvest","note":"Its outline from the front as the patent draws it: the ring about the barrel, the gas tube's boss on top, the set screws' foot underneath. The flat spring, which the patent draws end on below the boss on the part's right, is left out of the outline (it is a piece of its own). The bore is open: a section with a hole is drawn solid and the barrel fills it."}},"gaps":[{"what":"Its length, height and width","need":"No page publishes them. A straight side view and a straight front view of SA7-SM, or the maker's figures, would replace the fit and the patent's proportions"},{"what":"The rear face","need":"No photo on file shows it: the gas tube's hole is the patent's (FIG. 4)"},{"what":"The flutes' depth and the flat spring's thickness","need":"A view from the end square to the block, or a photo of the spring edge on"},{"what":"The rear set screw's place","need":"A view square to the underside (the left photo shows the front hole whole and the rear one half hidden by the face's rim)"}]},"spikes-tactical-sdr100a":{"id":"spikes-tactical-sdr100a","name":"Delta Ring Assembly w/Mil-Spec Barrel Nut","manufacturer":"Spike's Tactical","sku":"SDR100A","url":"https://www.spikestactical.com/collections/parts/delta-ring-assembly-w-mil-spec-barrel-nut/","category":"barrel_nut","description":"The standard barrel nut with its delta ring, weld spring and snap ring already on it: the nut threads onto the upper receiver's nose and clamps the barrel extension, and the spring-loaded ring on it holds the rear of a drop-in handguard. Spike's: \"The Spike's Tactical Delta Ring assembly is fully Mil-Spec and comes ready for you to finish your new upper.\" \"Inside the package you'll find everything already installed so you can quickly mount your barrel\".","weight":"spikes-tactical-sdr100a.weight","occupies":["delta_ring"],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"mount":{"origin":[0,0,0],"note":"Part frame: the receiver's front face on the bore axis, +x toward the muzzle."}},"interfaces":{"handguard_mount":{"type":"ar15.handguard_mount","role":"handguard","anchor":"mount","params":{"nut":"standard"},"flips":false,"note":"Spike's: \"fully Mil-Spec\"; its nut is the mil-spec nut, threaded for the receiver's 1.250-18 UNEF (bcm-m4-upper.thread_major_d)."},"delta_ring":{"type":"ar15.delta_ring","role":"nut","anchor":"mount","params":{},"flips":false,"note":"Its own ring is on it (occupies: [delta_ring]): nothing else goes here."},"drop_in":{"type":"ar15.drop_in","role":"nut","params":{},"flips":false,"note":"The nut, and the ring it brings, hold a drop-in handguard's rear; it is in the delta ring's slot too (occupies)."}},"materials":{"nut":{"label":"Barrel nut","finish":"phosphate","recolorable":false,"color":"steel-phosphate-black","note":"Spike's: \"The barrel nut is machined from tough chromoly steel, is properly heat treated, and of course completed with a phosphate finish.\" Its front photo (b8505e770f0f) has the flange a satin black (a phosphate oiled), blacker than BCM's dry nut: its teeth read #1e1d1b in shade to #504c4a where lit, with no flat lit evenly enough to fit to, so it is drawn in the catalog's black phosphate (steel-phosphate-black, fitted to BCM's gas block), by its look. One look."},"ring":{"label":"Delta ring","finish":"anodized","recolorable":false,"color":"placeholder-black","note":"Spike's: \"The delta ring itself is made of Mil-Spec aluminum and features a black anodized finish.\" Its front photo (b8505e770f0f) has the lands lit as a satin, sealed anodize is (#878789 on a lit land, a near-black between): a black on sealed anodize isn't fitted to a photo, its finish type is its look (the Army's drawing asks a flat black; Spike's photos show this one with a sheen, unlike BCM's). One look."},"spring":{"label":"Weld spring and snap ring","finish":"phosphate","recolorable":false,"color":"steel-phosphate-charcoal","note":"Spike's: \"We also finished the weld spring and snap ring in a phosphate finish per Mil-Spec.\" Its rear photo (009abbbe250f) has the snap ring a dry mid grey beside the black ring and nut (#5c5854 on its lit face), as a phosphate is: the catalog's charcoal phosphate, not fitted to it (the spring is inside the ring and the snap ring a sliver behind it in the app's views). One look."}},"components":{},"geometry":{"model":"spikes-tactical-sdr100a.glb","components":{},"approximations":["Every size is the mil-spec parts' (std.ar15.barrel_nut_*, std.ar15.slip_ring_*: the Army's drawings for the ring and the weld spring, the reference CAD set for the nut and the snap ring), because Spike's states none and says the assembly is \"fully Mil-Spec\"; its two photos are obliques from in front and behind and aren't measured, but bear out the count of the ring's lands and the spacing of the nut's notches.","The nut placed as the Army's assembly has it, its inner shoulder on the barrel extension's flange; the ring forward on its spring with its lip against the nut's flange, its front then flush with the nut's front face (as Spike's front photo shows it). A drop-in handguard presses it back by as much as the handguard's length asks, which isn't drawn.","The nut's thread is a helix of the receiver's pitch ending where the receiver's front face stands, turned so that at the top of the turn its roots meet the crests of the upper's thread rings.","The weld spring: four sections of the drawing's strip, three waves round, each in the opposite phase to the next so that they touch crest to trough (the drawing's diamonds, welded there), pressed to the height between the snap ring and the ring's lip (0.50 of its free .552); its gap, the ring's notch, the snap ring's gap and the nut's top notch all at the top, where the gas tube passes, as Spike's rear photo has the snap ring's ears and the spring's gap over the ring's notch.","The snap ring is drawn seated: as wide as the nut's groove and its inside on the groove's floor (the reference model's ring is drawn free, 0.050 thick and 1.372 across inside); a flat ring, its gap's faces square, a hole in each end, and its inside the reference model's: the 1.372 circle at its ends' lugs (to 42 degrees from the gap) and over its back (from 127.6), cut away between them to 1.503 across at 73.4 degrees (the photos show the ends wider than the ring beside them); the model's two arcs there are drawn as a half cosine each side of the waist, and the whole inside comes down by the 0.0195 the ring is sprung into the groove.","Not drawn: the 0.010 rounds inside the ring's lip and the 0.005 rounds at the nut's groove."],"ledger":["spikes-tactical-sdr100a.length","spikes-tactical-sdr100a.flange_diameter","spikes-tactical-sdr100a.ring_outside_diameter","spikes-tactical-sdr100a.notches","spikes-tactical-sdr100a.ring_lands"]},"profiles":{},"gaps":[{"what":"Spike's own figures","need":"Any size Spike's states for the nut or the ring: every size here is the mil-spec parts'"},{"what":"A seller on file","need":"Spike's Tactical isn't a seller on file; no seller on file was found carrying SDR100A"}]},"streamlight-protac-rail-mount-hl-x":{"id":"streamlight-protac-rail-mount-hl-x","name":"ProTac Rail Mount HL-X","manufacturer":"Streamlight","sku":"88066","url":"https://www.streamlight.com/products/detail/protac-rail-mount-hl-x","category":"light","description":"Streamlight's ProTac Rail Mount HL-X long gun light: 1,000 lumens, a machined aluminium body, a push-button tail switch or the remote pressure switch that comes with it. \"Integrated rail clamp attaches to MIL-STD-1913 (Picatinny) rails\", and the M-LOK mount in the box (Streamlight 88300) holds it on a handguard's slot, over its top corner and leaning out. Black only.","weight":"streamlight-protac-rail-mount-hl-x.weight","fitments":{"label":"Batteries","default":"cr123a","options":{"cr123a":{"label":"Two CR123A cells (88066)","sku":"88066","params":{},"source":"https://www.streamlight.com/docs/default-source/info-sheet-with-part-numbers/protacrailmounthl-x_sup.pdf"},"sl_b26":{"label":"SL-B26 USB pack (88071)","sku":"88071","params":{},"weight":"streamlight-protac-rail-mount-hl-x.weight_sl_b26","source":"https://www.streamlight.com/docs/default-source/info-sheet-with-part-numbers/protacrailmounthl-x_sup.pdf"}}},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":[0,0,0],"note":"On the rail's top at the middle of its clamp (the cross bolt), +x toward the lens, +y away from the rail."},"mlok":{"origin":["({.band_front_x} - {.band_rear_x}) / 2","{.mlok_lip_height} - {.mlok_screw_below_corner} * sin({.mlok_seat_angle}) + {.mlok_plate_thickness} * cos({.mlok_seat_angle})","{.mlok_seat_hole_from_corner} - {.mlok_screw_below_corner} * cos({.mlok_seat_angle}) - {.mlok_plate_thickness} * sin({.mlok_seat_angle})"],"x":[1,0,0],"y":[0,"-cos({.mlok_seat_angle})","sin({.mlok_seat_angle})"],"note":"The middle of the M-LOK mount's two screws on the face that goes on the handguard, +y out of that face (the plate's outer normal), +x toward the lens. On a handguard's right face the light's axis then stands 1.2 in above the slot's centre and 0.43 in out from the face, leaning out 45 degrees; on the left face the mount is turned over and the light hangs under the face's lower edge, as 1lumen photographed the HL-X Pro on it (a page the harvester was refused)."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":"={.clamp_length} / 2","clamp_front":"={.clamp_length} / 2"},"flips":false,"note":"Streamlight: \"Integrated rail clamp attaches to MIL-STD-1913 (Picatinny) rails\"; the instructions: \"For the 1913 rail, rotate the thumb wheel until the clamp is fully open. Slip the clamp over the 1913 rail of the weapon and retighten the thumb wheel securely.\" The clamp's jaws are 1.2 in long about the cross bolt."},"mlok":{"type":"mlok","role":"accessory","anchor":"mlok","params":{"lugs":"={.lugs}","reach_inside":"={.reach_inside}"},"flips":false,"note":"Streamlight's M-LOK mount, item 88300, in the box with both packages: two 10-24 screws into two T-nuts, both in the one slot the plate is centred on (every installed photo on file); no page states a slot count. GRITR: \"It provides users with an ambidextrous platform to mount these weapon lights in various positions on M-LOK compatible handguards and forends.\" How far its nuts reach inside isn't published, so that check reads as unmade."}},"materials":{"body":{"label":"Body, clamp and M-LOK mount","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized_matte","color":"placeholder-black","source":"https://www.streamlight.com/products/detail/protac-rail-mount-hl-x"}},"default":"black","note":"Streamlight's fact sheet: \"6000 Series machined aircraft aluminum with black anodized finish\"; Primary Arms' table: \"Finish Hardcoat Anodized\". Black is the only colour this light is sold in (the page's row \"Colors Black\"; one black swatch on the info sheet; both packages, 88066 and 88071, are black). The tan light in sellers' galleries is the HL-X Pro, another product. The head, the tube, the tail cap, the clamp's two jaws and the M-LOK mount are the one anodize (the mount sold alone: GRITR \"Color: Black, Finish: Anodized\"; Battery Junction \"Color Black\"; milgear.fi's seven photos of it are black), drawn matte (`anodized_matte`, since 2026-10-06: Primary Arms' photographs have a soft sheen and no bright line along the tube, which a receiver's satin `anodized` draws on a round part); the black is the placeholder the optics use, not matched. The tail cap's rubber button is drawn in it too: the body is its outline turned, and the button's own size isn't read."},"lens":{"label":"Lens","finish":"glass","recolorable":false,"color":"glass-clear","note":"Streamlight's fact sheet: \"High-temperature, shock-mounted, AR coated, impact-resistant BOROFLOAT glass\"."},"hardware":{"label":"Screws and thumb wheel","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The clamp's cross bolt, its knurled thumb wheel and the fixed jaw's two socket-head screws: black, and flatter than the anodize beside them in Primary Arms' photographs of the light from behind and from ahead (the wheel's knurl a shade greyer than the jaw). What they are made of and their finish aren't named on a page on file: drawn as dark steel. The M-LOK mount's two 10-24 button heads are black too, a darker black than the mount's face in the maker's studio picture of it (GRITR 923578) and in its _4 on a handguard."}},"components":{},"geometry":{"components":{"body":"streamlight-protac-rail-mount-hl-x.body.glb","rail_clamp":"streamlight-protac-rail-mount-hl-x.rail_clamp.glb","mlok":"streamlight-protac-rail-mount-hl-x.mlok.glb"},"approximations":["The body is Primary Arms' photo straight down on the light, its outline's radius revolved about the axis and scaled by the published length (5.43 in) with the end rims' perspective taken off: the head comes out 1.42 in across its fins, 0.03 under the fact sheet's Width (1.45 in), which no document ties to the head. The bezel's scallops, the tail cap's guard ears and its switch, the knurling and the engraving aren't drawn; the tail cap is the push-button one.","Between the clamp's jaws the photo shows the jaws and not the body: the two bands the legs hang from are drawn at the diameter they show beside the jaws, each as long as the two bands' mean (0.33 in), and the engraved zone between them at the diameter the kit picture's upper edge gives (0.85 in).","The two legs under the body are blocks as long as the bands and as wide as a Picatinny rail (their section isn't in any straight view); the clamp's jaws are blocks whose inner faces are the rail's own head in section (MIL-STD-1913's, since 2026-10-12) as far down as they reach, 0.116 in under the rail's top, without the hooks that reach further under the rail, the fixed jaw's raised middle and two screw heads on it, the moving jaw's corners chamfered as the plan shows. The moving jaw's height and where the cross bolt sits are from an oblique photo through a fitted camera; the fixed jaw's height and its screws' places from an elevated kit picture: each to about 0.05 in.","The clamp is drawn as open as it was photographed off a rail (the moving jaw 0.67 in from the axis, the thumb wheel's end 1.05 in): tightened on a rail the jaw and the wheel stand further in. The body's axis is put above the rail by the cross bolt lying on the floor of a rail slot; riding higher in the slot it would be up to 0.03 in nearer.","The M-LOK mount (2026-10-19) is one section along its length, from a camera fitted to milgear.fi's four photos of it alone and scaled by its two screws, the M-LOK interval apart: its plate 0.80 in from the corner to its lower edge and 0.22 thick, its seat 0.69 across and 0.23 thick, the angle between them 135 degrees (what it has to fit: the photos read 129.5 ± 4), the lips 0.22 and 0.11 wide and 0.064 over the floor, each figure to 0.03 to 0.05 in. Its edges are broken at an assumed 0.02 in (GRITR: \"beveled ends and corners\"); the counterbores' depths are the fit's weakest figures (0.066 ± 0.06 and 0.074 ± 0.066).","On the M-LOK mount the light's legs stand on the seat's floor over its two holes, as on a rail's top on the clamp: the legs are drawn as wide as a rail (the body's assumption since batch 3), and the mount's floor between its lips is 0.36 in across, so on it the legs stand over both lips. The mount is centred along the light on the middle of its two legs; its two holes are 0.852 in apart and the legs' middles 0.897, each inside its leg.","The M-LOK mount's lugs are two crescents about each screw on the plate's inner face: a ring cut by the slot's sides (std.mlok.slot_width), out to where the slot's ends allow (its length less the interval, halved), the ring's inner radius and its height off the face assumed. The 10-24 button heads fill their counterbores and stand an assumed 0.05 in proud as a dome, with no socket; the two 8-32 screws under the seat, the T-nuts (inside the handguard) and the hex keys aren't drawn.","The glass is a disc at the bezel's front at the diameter it shows inside the bezel (1.05 in); its recess and the reflector behind it aren't drawn. Edges broken at 0.006 to 0.012 in."],"ledger":["streamlight-protac-rail-mount-hl-x.length","streamlight-protac-rail-mount-hl-x.head_diameter","streamlight-protac-rail-mount-hl-x.body_diameter","streamlight-protac-rail-mount-hl-x.axis_above_mount","streamlight-protac-rail-mount-hl-x.clamp_length","streamlight-protac-rail-mount-hl-x.mlok_length","streamlight-protac-rail-mount-hl-x.mlok_plate_height","streamlight-protac-rail-mount-hl-x.mlok_seat_angle","streamlight-protac-rail-mount-hl-x.mlok_axis_above_screws","streamlight-protac-rail-mount-hl-x.mlok_axis_out_of_face"]},"profiles":{"plan":{"plane":"xz","origin":"on the body's axis at the clamp's middle (the thumb wheel's centre, column 1142), x toward the lens, z toward the thumb wheel","offset":{},"points":[[-2.483,0.259],[-2.483,-0.239],[-2.457,-0.265],[-2.451,-0.285],[-2.443,-0.368],[-2.463,-0.408],[-2.463,-0.454],[-2.45,-0.467],[-2.137,-0.466],[-2.074,-0.501],[-2.045,-0.506],[-1.37,-0.505],[-1.341,-0.493],[-1.183,-0.493],[-1.162,-0.461],[-0.668,-0.459],[-0.63,-0.468],[-0.561,-0.468],[-0.554,-0.521],[-0.532,-0.54],[-0.463,-0.545],[-0.397,-0.542],[-0.351,-0.522],[-0.302,-0.528],[-0.288,-0.545],[-0.273,-0.55],[0.248,-0.549],[0.268,-0.529],[0.314,-0.523],[0.328,-0.523],[0.348,-0.537],[0.383,-0.546],[0.478,-0.546],[0.515,-0.537],[0.526,-0.527],[0.536,-0.468],[0.659,-0.459],[0.815,-0.461],[0.825,-0.5],[0.864,-0.521],[1.146,-0.524],[1.328,-0.627],[1.501,-0.632],[1.53,-0.655],[1.585,-0.664],[1.789,-0.677],[1.807,-0.677],[1.827,-0.666],[1.864,-0.666],[1.877,-0.702],[1.893,-0.715],[1.942,-0.712],[1.952,-0.701],[1.965,-0.668],[1.994,-0.668],[2.007,-0.701],[2.017,-0.711],[2.049,-0.714],[2.075,-0.711],[2.085,-0.701],[2.098,-0.668],[2.124,-0.668],[2.14,-0.704],[2.156,-0.714],[2.208,-0.711],[2.231,-0.668],[2.254,-0.667],[2.27,-0.703],[2.283,-0.714],[2.343,-0.708],[2.363,-0.667],[2.398,-0.667],[2.412,-0.679],[2.946,-0.677],[2.946,0.635],[2.939,0.659],[2.923,0.684],[2.877,0.692],[2.412,0.688],[2.395,0.676],[2.361,0.679],[2.348,0.698],[2.326,0.713],[2.277,0.713],[2.26,0.679],[2.228,0.678],[2.199,0.713],[2.147,0.713],[2.13,0.678],[2.104,0.675],[2.088,0.685],[2.069,0.713],[2.017,0.712],[1.997,0.675],[1.974,0.675],[1.955,0.685],[1.942,0.709],[1.905,0.712],[1.882,0.706],[1.874,0.679],[1.867,0.674],[1.763,0.68],[1.567,0.665],[1.536,0.659],[1.498,0.633],[1.345,0.632],[1.302,0.615],[1.149,0.525],[0.873,0.524],[0.85,0.515],[0.825,0.497],[0.818,0.461],[0.613,0.46],[0.598,0.47],[0.595,0.568],[0.487,0.673],[0.181,0.675],[0.176,0.686],[0.154,0.687],[0.193,0.695],[0.2,0.702],[0.204,0.749],[0.268,0.753],[0.31,0.766],[0.312,1.013],[0.305,1.02],[0.233,1.017],[0.252,1.025],[0.239,1.029],[0.086,1.034],[0.078,1.048],[0.046,1.051],[-0.069,1.051],[-0.089,1.034],[-0.158,1.036],[-0.167,1.016],[-0.19,1.019],[-0.193,1.033],[-0.245,1.03],[-0.227,1.022],[-0.305,1.024],[-0.312,1.011],[-0.312,0.772],[-0.296,0.762],[-0.21,0.754],[-0.206,0.706],[-0.199,0.699],[-0.128,0.689],[-0.19,0.685],[-0.196,0.673],[-0.489,0.669],[-0.609,0.555],[-0.612,0.475],[-0.619,0.465],[-0.679,0.459],[-1.16,0.46],[-1.175,0.496],[-1.183,0.5],[-1.344,0.5],[-1.372,0.511],[-2.051,0.509],[-2.077,0.503],[-2.137,0.471],[-2.436,0.47],[-2.456,0.464],[-2.46,0.457],[-2.46,0.406],[-2.443,0.368],[-2.451,0.299],[-2.46,0.279]],"scaleRefs":["streamlight-protac-rail-mount-hl-x.body_diameter"],"inputs":{"streamlight-protac-rail-mount-hl-x.body_diameter":0.92,"streamlight-protac-rail-mount-hl-x.front_x":2.946,"streamlight-protac-rail-mount-hl-x.rear_x":2.483},"tolerance":0.004,"photo":"references/streamlight-protac-rail-mount-hl-x 96bbc99c1b2a (Primary Arms 88066_00.jpg: the light from above its clamp, thumb wheel up, 2200 x 1467)","method":"luminance < 200, largest piece, holes filled; scale from streamlight-protac-rail-mount-hl-x.body_diameter = 0.92 in, the tube's own width column by column: 319.4 px over columns 862–926, 319.7 px over columns 1384–1544; a line through them (rms 0.14 px) changes +0.1% from column 862 to 1544, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 347.3 px/in there. The axis is the tube's centre line (tilt -0.17°, rms 0.05 px); origin at column 1142 of the photo, on the tube's axis; clipped to x min -{.rear_x} = -2.483, x max {.front_x} = 2.946; Douglas-Peucker at 0.004 in with the extremes kept: 170 points (IoU 0.998 with the full outline); tip to tip the silhouette is 5.57 in at the tube's scale, 2.6% over the published 5.43: the two end rims' near sides, 0.68 and 0.46 in nearer a lens 23 in off, which is what the scale allows for; checks: height 1.766 ± 0.018 in vs streamlight-protac-rail-mount-hl-x.width 1.766 ± 0.012 (provisional): agrees (tools/trace.py)","via":"harvest","note":"The whole light from above: head, body, tail cap, the clamp's moving jaw and thumb wheel on one side (+z) and its fixed jaw with two screw heads on the other. The ends are cut at the end planes: the rims' near sides show 0.09 and 0.05 in past them."},"body":{"plane":"xz","origin":"on the body's axis at the clamp's middle (the thumb wheel's centre, column 1142), x toward the lens, z toward the thumb wheel","offset":{},"points":[[-2.483,0.239],[-2.483,-0.239],[-2.457,-0.265],[-2.451,-0.285],[-2.449,-0.331],[-2.443,-0.348],[-2.441,-0.467],[-2.137,-0.466],[-2.074,-0.501],[-2.045,-0.506],[-1.37,-0.505],[-1.341,-0.493],[-1.183,-0.493],[-1.175,-0.488],[-1.162,-0.461],[-0.668,-0.459],[-0.616,-0.468],[-0.561,-0.468],[-0.554,-0.521],[-0.544,-0.534],[-0.532,-0.54],[-0.463,-0.545],[-0.397,-0.542],[-0.374,-0.536],[-0.357,-0.522],[-0.351,-0.522],[-0.302,-0.528],[-0.289,-0.538],[-0.288,-0.545],[-0.273,-0.55],[0.248,-0.549],[0.268,-0.529],[0.314,-0.523],[0.328,-0.523],[0.348,-0.537],[0.383,-0.546],[0.478,-0.546],[0.515,-0.537],[0.526,-0.527],[0.531,-0.512],[0.531,-0.472],[0.536,-0.468],[0.582,-0.467],[0.613,-0.459],[0.818,-0.461],[0.825,-0.497],[0.835,-0.507],[0.864,-0.521],[1.146,-0.524],[1.314,-0.621],[1.34,-0.63],[1.501,-0.632],[1.539,-0.658],[1.743,-0.675],[1.807,-0.677],[1.827,-0.666],[1.864,-0.666],[1.874,-0.679],[1.88,-0.704],[1.905,-0.712],[1.936,-0.712],[1.947,-0.704],[1.965,-0.668],[1.994,-0.668],[2.017,-0.711],[2.069,-0.711],[2.094,-0.681],[2.098,-0.668],[2.124,-0.668],[2.14,-0.704],[2.156,-0.714],[2.205,-0.711],[2.231,-0.668],[2.254,-0.667],[2.27,-0.703],[2.283,-0.714],[2.335,-0.71],[2.353,-0.689],[2.363,-0.667],[2.398,-0.667],[2.412,-0.679],[2.926,-0.677],[2.939,-0.658],[2.946,-0.634],[2.946,0.635],[2.939,0.659],[2.926,0.678],[2.412,0.679],[2.398,0.667],[2.363,0.667],[2.348,0.698],[2.335,0.711],[2.323,0.713],[2.277,0.71],[2.254,0.667],[2.231,0.667],[2.209,0.706],[2.199,0.713],[2.147,0.71],[2.124,0.667],[2.098,0.666],[2.076,0.708],[2.069,0.713],[2.017,0.712],[1.994,0.669],[1.965,0.669],[1.947,0.705],[1.936,0.712],[1.905,0.712],[1.88,0.705],[1.874,0.679],[1.864,0.666],[1.827,0.666],[1.807,0.677],[1.625,0.662],[1.585,0.665],[1.539,0.659],[1.501,0.633],[1.34,0.629],[1.314,0.621],[1.146,0.522],[0.864,0.521],[0.835,0.507],[0.825,0.497],[0.818,0.461],[0.659,0.457],[0.613,0.46],[0.582,0.469],[0.536,0.468],[0.531,0.473],[0.531,0.513],[0.526,0.527],[0.515,0.537],[0.478,0.546],[0.383,0.546],[0.348,0.537],[0.328,0.522],[0.314,0.522],[0.268,0.528],[0.248,0.548],[0.167,0.551],[-0.273,0.549],[-0.288,0.543],[-0.289,0.536],[-0.302,0.526],[-0.32,0.529],[-0.351,0.523],[-0.357,0.523],[-0.374,0.537],[-0.397,0.543],[-0.515,0.543],[-0.544,0.534],[-0.554,0.521],[-0.561,0.468],[-0.616,0.468],[-0.668,0.459],[-1.162,0.46],[-1.175,0.487],[-1.183,0.492],[-1.341,0.494],[-1.37,0.505],[-1.743,0.501],[-1.749,0.507],[-2.045,0.506],[-2.074,0.5],[-2.137,0.466],[-2.441,0.467],[-2.443,0.348],[-2.449,0.331],[-2.451,0.285],[-2.457,0.265]],"scaleRefs":["streamlight-protac-rail-mount-hl-x.body_diameter"],"inputs":{"streamlight-protac-rail-mount-hl-x.body_diameter":0.92,"streamlight-protac-rail-mount-hl-x.front_x":2.946,"streamlight-protac-rail-mount-hl-x.rear_x":2.483},"tolerance":0.003,"photo":"references/streamlight-protac-rail-mount-hl-x 96bbc99c1b2a (Primary Arms 88066_00.jpg: the turned body alone)","method":"luminance < 200, largest piece, holes filled; the turned body alone: at each column the smaller of the dark run's reach above and below the tube's axis, taken both ways; scale from streamlight-protac-rail-mount-hl-x.body_diameter = 0.92 in, the tube's own width column by column: 319.4 px over columns 862–926, 319.7 px over columns 1384–1544; a line through them (rms 0.14 px) changes +0.1% from column 862 to 1544, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1100)/width, the lens's axis taken to meet the image at column 1100; 347.3 px/in there. The axis is the tube's centre line (tilt -0.17°, rms 0.05 px); origin at column 1142 of the photo, on the tube's axis; clipped to x min -{.rear_x} = -2.483, x max {.front_x} = 2.946; Douglas-Peucker at 0.003 in with the extremes kept: 171 points (IoU 0.998 with the full outline); checks: height (tooth tops, max over 0.1 in windows) along x [1.85, 2.3] 1.415 ± 0.015 in vs streamlight-protac-rail-mount-hl-x.head_diameter 1.424 ± 0.012 (provisional): agrees; height (tooth tops, max over 0.05 in windows) along x [-1.05, -0.75] 0.921 ± 0.012 in vs streamlight-protac-rail-mount-hl-x.body_diameter 0.92 ± 0.006 (corroborated): agrees (tools/trace.py)","via":"harvest","note":"The body of revolution: bezel, four fins, the head's taper, neck ring, tube, tail cap. Between the clamp's two jaws it is the fixed jaw's reach that shows (0.55 in), not the body: the model puts the two bands' own radius there."}},"gaps":[{"what":"The M-LOK mount's section is read through a camera fitted to four photos of it alone (each figure to 0.03 to 0.05 in); its angle is what it has to fit (135 degrees), 1.4 of the photos' ± from their 129.5; where it then holds the light (the axis 1.20 in above the slot's centre) is 0.06 in above what the maker's side view of the light on it reads (1.14)","need":"A straight end view of the light on the mount (from the muzzle or the tail), or a drawing of 88300. 1lumen's photos of the HL-X Pro on it (a straight left side view, and one from the tail) and CatOutdoors' right side view of the Rail Mount 1 on it are the best views found; both sites refused the harvester (1lumen's firewall answered the images, CatOutdoors' robots.txt answered 403)"},{"what":"The light's legs: their width, and the mount's floor between its lips (0.36 in) says they are narrower than the rail they are drawn as wide as","need":"A view of the light's underside with the clamp off (the scout pattern's two ports), or from its end; then the legs and the clamp's jaws drawn again together"},{"what":"How the mount fits a particular handguard: it wraps the corner between a side face and the 45-degree face above it, its inner corner 0.31 in above the slot's centre. It sits clear on BCM's MCMR and Geissele's MK16 (lines cast through both models); Aero's R-ONE's side flat runs to 0.33 above its slots and leans 2 degrees, so there its seat's inner corner and its plate's lower edge each stand a hundredth or so into the face","need":"The inner corner's height to a hundredth (a straight end view), or a photo of it on a handguard whose side face runs higher; Streamlight's own photos show it on a handguard whose side face runs to about the plate's top edge"},{"what":"The M-LOK mount's weight","need":"A figure of the piece alone: the one seller's 1.28 oz is the package as boxed (its shipping weight); the build counts the light's published 6.4 oz on either mount"},{"what":"What the fact sheet's Width (1.45 in) and Height (1.72 in) span","need":"A dimensioned drawing. The Height matches the span across the head and out to the thumb wheel's end (1.71 to 1.77 in in two photos); the Width is drawn across the head in an infographic, where the photos scaled by the length read 1.42"},{"what":"A straight side view with a rail in it (how high the body sits, the jaws' hooks, the legs' section)","need":"A photo of the light clamped on a rail from square to its side, or from its end"},{"what":"The remote switch, its tail cap and cable, and the retaining clips","need":"Not rigid parts of the light: not drawn (the category's rule)"}]},"superlative-750-gas-block":{"id":"superlative-750-gas-block","name":".750\" Adjustable Gas Block, Bleed Off - Set Screw","manufacturer":"Superlative Arms","sku":"SABO-DI-750SM","url":"https://www.righttobear.com/superlative-arms-750-adjustable-gas-block-bleed-sabo-di-750sm/","category":"gas_block","description":"Superlative Arms' adjustable \"bleed off\" gas block for a .750 in journal, held by two 10-32 set screws: 416 stainless, sold with a black Melonite (QPQ) finish (SABO-DI-750SM, the number here), in matte stainless or with a tan DLC coat. Its adjustment screw is on the front face and lets the gas it doesn't use out of a port beside it, forward; a detent outside the block holds the setting (30 locked positions). The gas tube's roll pin and a 3/32 hex key are in the box; the gas tube isn't.","weight":"superlative-750-gas-block.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"journal":{"origin":[0,0,0],"note":"On the bore axis at the gas port, +x toward the muzzle. The port is inside and unpublished: it is taken where the standard tube's gas hole lands with its pin in the block's cross hole, 0.271 in ahead of the rear face (port_from_rear; the Army's front sight has .270)."},"gas_tube":{"origin":[0,"{.tube_hole_above_bore}",0],"x":[-1,0,0],"note":"The tube's hole at the port, +x rearward toward the receiver: 0.685 in above the bore by Primary Arms' photo of the rear face (the hole stands high in its boss). That is 0.060 above the Army's .625 for a front sight, where the BCM and Aero blocks have theirs: read on this block's own photo, not taken from the standard."}},"interfaces":{"gas_journal":{"type":"ar15.gas_journal","role":"block","anchor":"journal","params":{"journal_od":"={.journal_id}"},"flips":false,"note":"Primary Arms: \"Built for a .750\\\" gas block journal, this set screw gas block bleeds excess gas forward instead of restricting flow\". Wing Tactical (one page for both sizes): \"compatible with any AR-15 and AR-10 barrel that has a .625\\\" or .750\\\" diameter at the gas port area\". Primary Arms: \"Low profile: 1.383\\\" height fits under most handguards\": its top is 0.813 in above the bore and the detent's tab reaches 0.531 in from the axis on the left."},"gas_tube":{"type":"ar15.gas_tube","role":"block","anchor":"gas_tube","params":{},"flips":false,"note":"Right To Bear: \"1x Gas Tube Roll Pins\" in the box and \"***Gas Tube NOT Included***\". No page on file says which gas tube it takes."}},"materials":{"body":{"label":"Gas block","finish":"nitride","recolorable":false,"color":"steel-nitride-black","options":{"melonite":{"label":"Melonite","finish":"nitride","color":"steel-nitride-black","sku":"SABO-DI-750SM","source":"https://www.righttobear.com/superlative-arms-750-adjustable-gas-block-bleed-sabo-di-750sm/"},"stainless":{"label":"Stainless Steel, Matte","finish":"steel","color":"superlative-matte-stainless","sku":"SABO-DI-750SS","source":"https://www.righttobear.com/superlative-arms-750-adjustable-gas-block-bleed-sabo-di-750ss/"},"tan":{"label":"Tan DLC","finish":"steel","color":"superlative-tan-dlc","sku":"SABO-DI-750ST","source":"https://www.bauer-precision.com/superlative-arms-750-adjustable-gas-block-set-screw-stainless-steel-tan-dlc/"}},"default":"melonite","note":"One block of 416 stainless in three finishes, each under its own number. Melonite, SABO-DI-750SM (Right To Bear: \"Gas Block Material: 416 SS\", \"Finish: Melonite, QPQ\"; Blackstone: \"Black Melonite\"): a salt-bath nitride by its sellers' words, so the app's black nitride, whose colour is a black and isn't fitted to a photo (Primary Arms' photos of it read #282828 and #2f2f2f on its sides, with a finer, flatter face than a carrier's). Matte stainless, SABO-DI-750SS (Right To Bear: \"SKU: SABO-DI-750SS\", \"Finish - Stainless Steel, Matte\"): the bare steel blasted to an even pale grey with no bright line on it, so it is drawn as the app's matte steel in a matched colour and not as brushed stainless. Tan DLC, SABO-DI-750ST (Bauer Precision: \"SKU: SABO-DI-750ST UPC: 850011846759 MPN: SABO-DI-750ST\", \"Material: 416 Stainless Steel Finish: Tan Diamond-Like Carbon (DLC)\"; Arm or Ally and Huckleberry Arms carry the same number): a matte tan in the maker's pictures of it, a brassy gold in Wing Tactical's own photo of an older lot (Lot # 100417); the maker's is the one matched. Wing Tactical's one page lists the three (\"Finish: Melonite (Black), Matte stainless steel, or Tan DLC\"). The same shape in titanium (Primary Arms and others) is another product, of another weight, and isn't a colour of this one. The logo, the address and the patent's number lasered on the right side aren't drawn."},"hardware":{"label":"Adjustment screw","finish":"steel","recolorable":false,"color":"placeholder-black","note":"Black on the block in every finish: Primary Arms' photos of the Melonite one, Wing Tactical's of the stainless one (a80edfa7809c), the maker's pictures of the tan one (bc8e61f05e93)."},"pin":{"label":"Detent pin","finish":"steel","recolorable":false,"color":"placeholder-black","follows":{"slot":"body","options":{"stainless":{"finish":"stainless","color":"stainless-natural"},"tan":{"finish":"stainless","color":"stainless-natural"}}},"note":"The detent's pin along the left side. On the Melonite block it is black in its groove behind the pad (Primary Arms' left side photo, ab5b9b867b45), bare only where it shows through the tab's window; on the stainless block it is a bright polished pin (Wing Tactical's a80edfa7809c), and bright in the tab's window on the tan one (the maker's picture, 351d4aa42e07). The small socket screw at the tab's ear, bright on the tan and the stainless blocks, isn't drawn."},"screws":{"label":"Set screws","finish":"steel","recolorable":false,"color":"stainless-natural","note":"The two set screws in the foot: bright in every finish (the Melonite block in the marketing picture AR15Discounts shows, 0eababbbd865; the stainless one in Wing Tactical's 31f0f5230294; the tan one in the maker's 351d4aa42e07). Primary Arms' photos of the Melonite block show their tips darker in the bore; the app's natural-steel grey, not matched (a bright metal)."}},"components":{},"geometry":{"model":"superlative-750-gas-block.glb","components":{},"approximations":["Its section is the maker's own drawing of it from the front (nine callouts, one scale), run along the sellers' length. The body is taken to be the same on both sides: the side away from the detent is mirrored, and where the outline runs along the ring about the barrel it is drawn as the circle of the published width. Primary Arms' photo of the front face lies on the drawing's outline within 0.018 in, and its photo of the rear face (no tab there) on the mirrored body. The drawing is 287 pixels to the inch: the outline is within a pixel and a half of every callout but the foot's flat, which comes out 0.372 in wide against the 0.383 called out.","On the left, what stands outside that mirrored body in the drawing is drawn as the raised pad the left side photo shows, from the front face back to its step (0.218 in). Its surface is the drawing's outline; the photo has the step running a little further up and down the side than the drawing's bulge does.","The detent's tab is a block on the front face bounded by the drawing's own lines (its upper edge at the adjuster's height, its lower edge from its outer corner to the bore), at one thickness, 0.166 in: the two side photos read 0.182 and 0.151 for it, near a close lens and far from it. It is cut round the adjuster at the drawing's outer circle.","The detent's pin is where the drawing has its end, the small circle on the tab's ear: it runs back through the tab and the pad in a hole and lies in a groove in the ring's surface behind the pad's step, as far back as the left side photo has its rear end. The window across the tab's ear is at the pin's height, as wide as that photo shows it and as deep as the pin.","The adjustment screw stands 0.217 in out of the front face as photographed (closed: it backs out as it is opened): a neck and a head at the two side photos' diameters, the break round its end down to the drawing's inner circle, its socket at the box's 3/32 key, as deep as it is wide. The neck is taken to be round: the four detent flats on it (Wing Tactical: \"there are 4 clicks/revolution\") and its thread aren't drawn; the body's face is closed behind it.","The bleed-off port is the drawing's circle beside the adjuster, drawn one diameter deep: where it leads is inside and unpublished.","The gas tube's hole is where Primary Arms' rear photo has it (0.685 in above the bore, on the centre line), at the standard tube's diameter and the Army's depth past the pin. The roll pin's cross hole is where the two side photos have it along the block (0.311 in behind the front face), at the tube's height, since the pin crosses the tube (those photos read it 0.018 in lower), and at the standard pin's diameter. The gas port is where the standard tube's gas hole then lands, 0.271 in ahead of the rear face; the port up from the bore isn't drawn (inside).","The two side photos are close shots from a little above: what is off the block's middle plane reads low in them, and large where it is near the lens. Lengths along the block are taken from them as read (each ± says so); heights are taken from the drawing and the rear photo, and where only a side photo shows a thing (the pocket) its height is the reading taken up by what that photo's own two checks give, ± 0.025 in.","The two set screws are in the foot's flat on its middle line, 0.26 and 0.73 in ahead of the rear face by an oblique photo of a stainless block's underside whose diameter the page doesn't say (± 0.03), at the diameter they show there, 3/16 long (three sellers) from the barrel's surface down, which leaves their ends 0.008 in inside the flat; their sockets at the same 3/32 key (one key is in the box), as deep as wide. Their thread isn't drawn.","The flat-floored round pocket low on the left side is at mid length and as wide as the left side photo has it, its floor at the depth where its straight lower edge meets the flank. What it is for isn't said. None is drawn on the right: Primary Arms' right side photo shows none.","Edges broken at 0.006 in (the photos show a small break; its size isn't measured). Not drawn: the lasered logo and lettering on the right side, the screws' threads, the gas passages inside."],"ledger":["superlative-750-gas-block.journal_id","superlative-750-gas-block.length","superlative-750-gas-block.height","superlative-750-gas-block.width","superlative-750-gas-block.height_above_bore","superlative-750-gas-block.foot_below_bore","superlative-750-gas-block.foot_width","superlative-750-gas-block.boss_width","superlative-750-gas-block.tab_corner_z","superlative-750-gas-block.tab_corner_y","superlative-750-gas-block.port_from_rear","superlative-750-gas-block.tube_hole_above_bore","superlative-750-gas-block.adjuster_reach","superlative-750-gas-block.tab_thickness"]},"profiles":{"front":{"plane":"zy","origin":"the bore's axis","offset":{},"points":[[-0.463,0.068],[-0.463,-0.058],[-0.459,-0.061],[-0.459,-0.078],[-0.452,-0.096],[-0.449,-0.12],[-0.445,-0.124],[-0.445,-0.134],[-0.442,-0.138],[-0.442,-0.151],[-0.431,-0.172],[-0.431,-0.179],[-0.421,-0.193],[-0.417,-0.207],[-0.4,-0.242],[-0.379,-0.273],[-0.337,-0.318],[-0.337,-0.322],[-0.278,-0.381],[-0.278,-0.384],[-0.247,-0.423],[-0.24,-0.44],[-0.23,-0.454],[-0.226,-0.468],[-0.205,-0.499],[-0.205,-0.51],[-0.202,-0.513],[-0.195,-0.551],[-0.191,-0.555],[-0.191,-0.562],[-0.183,-0.571],[0.183,-0.571],[0.191,-0.555],[0.195,-0.531],[0.212,-0.489],[0.212,-0.478],[0.219,-0.471],[0.23,-0.447],[0.247,-0.426],[0.254,-0.412],[0.282,-0.381],[0.282,-0.378],[0.327,-0.332],[0.327,-0.329],[0.379,-0.273],[0.386,-0.256],[0.393,-0.249],[0.393,-0.242],[0.4,-0.228],[0.421,-0.197],[0.428,-0.169],[0.435,-0.162],[0.445,-0.12],[0.452,-0.11],[0.456,-0.064],[0.463,-0.058],[0.463,0.029],[0.459,0.033],[0.459,0.071],[0.456,0.075],[0.456,0.089],[0.452,0.092],[0.452,0.102],[0.449,0.106],[0.449,0.116],[0.442,0.134],[0.438,0.162],[0.424,0.182],[0.39,0.256],[0.275,0.398],[0.268,0.416],[0.257,0.426],[0.216,0.513],[0.209,0.52],[0.202,0.544],[0.198,0.548],[0.198,0.558],[0.191,0.576],[0.188,0.6],[0.184,0.603],[0.184,0.621],[0.181,0.624],[0.181,0.635],[0.174,0.652],[0.174,0.676],[0.16,0.694],[0.157,0.718],[0.117,0.769],[0.113,0.769],[0.085,0.793],[0.05,0.803],[0.043,0.81],[-0.03,0.81],[-0.033,0.807],[-0.064,0.803],[-0.078,0.793],[-0.106,0.779],[-0.143,0.743],[-0.163,0.701],[-0.174,0.69],[-0.174,0.583],[-0.177,0.579],[-0.177,0.551],[-0.188,0.534],[-0.188,0.523],[-0.198,0.503],[-0.216,0.482],[-0.216,0.478],[-0.247,0.45],[-0.256,0.438],[-0.29,0.421],[-0.297,0.421],[-0.315,0.41],[-0.332,0.41],[-0.336,0.407],[-0.343,0.407],[-0.357,0.4],[-0.363,0.389],[-0.386,0.374],[-0.386,0.349],[-0.39,0.346],[-0.39,0.283],[-0.393,0.28],[-0.393,0.266],[-0.403,0.242],[-0.407,0.224],[-0.442,0.155],[-0.449,0.116],[-0.456,0.099],[-0.456,0.089],[-0.459,0.085],[-0.459,0.071]],"features":{"tab":[[[-0.016,0.487],[-0.51,0.487],[-0.51,0.364],[-0.231,0.168],[-0.016,0.168]]]},"scaleRefs":["superlative-750-gas-block.height_above_bore","superlative-750-gas-block.foot_below_bore","superlative-750-gas-block.width"],"inputs":{"superlative-750-gas-block.foot_below_bore":0.57,"superlative-750-gas-block.height_above_bore":0.813,"superlative-750-gas-block.width":0.93},"tolerance":0.002,"photo":"references/superlative-750-gas-block 54b07ecfded4 (Right To Bear's gallery image 13471, the maker's drawing '.750\" ADJUSTABLE GAS BLOCK, SOLID' (fcaac37db433), its dimension lines taken off outside the outline (derived-54b07ecfded4.manifest.json), 750 x 750)","method":"luminance < 128, largest piece, holes filled, opening after the fill 5 px ×1, inset 1 px (half the outline's stroke); frame from the reviewed holes top, flat, right, left (287.5 px/in, rms 0.002 in over 4 points); origin at the photo's frame; Douglas-Peucker at 0.002 in with the extremes kept: 132 points (IoU 0.996 with the full outline); the frame is the drawing's own extension lines: the boss's top (row 142) and the foot's flat (row 540) on the bore's vertical centre line (column 373.5), and the ring's two sides (columns 240 and 507) on its horizontal one (row 375): four published sizes (0.813, 0.570 and 0.930 halved each way) in one least-squares fit; the filled outline is pulled in by half a stroke; features through the same placement (tab: The detent's tab on the front face, bounded as the drawing's own lines bound it: its upper edge (the level line from the adjuster's circle to the outline, row 235.5), its inner end (the short line from the adjuster's circle down to the bore's, column 378), its lower edge (the line from the outer corner at (486.7, 294.2) to the bore's circle at (466.7, 308.3), carried on both ways). Its outer side is the outline itself and its inner side the bore: a model takes this polygon where it lies inside the outline and outside the bore and the adjuster.) (tools/trace.py)","via":"harvest","note":"Its outline from the front, as its maker draws it: the ring about the barrel, the gas tube's boss on top, the set screws' foot underneath, and on the part's left the detent's tab and the pad behind it standing outside the ring. The other side is the body's own: a model mirrors it. The bore is open: a section with a hole is drawn solid and the barrel fills it."},"side":{"plane":"xy","origin":"the bore's axis at the gas port","offset":{},"points":[[-0.278,-0.208],[-0.272,-0.548],[-0.264,-0.564],[-0.25,-0.568],[0.193,-0.568],[0.69,-0.567],[0.708,-0.564],[0.721,-0.551],[0.737,-0.193],[0.739,0.124],[0.734,0.289],[0.737,0.295],[0.879,0.297],[0.883,0.309],[0.886,0.386],[0.9,0.398],[0.897,0.411],[0.937,0.413],[0.951,0.432],[0.953,0.534],[0.942,0.559],[0.925,0.564],[0.824,0.564],[0.808,0.556],[0.732,0.559],[0.729,0.766],[0.726,0.793],[0.713,0.809],[-0.173,0.812],[-0.18,0.808],[-0.256,0.813],[-0.268,0.797],[-0.273,0.72]],"scaleRefs":["superlative-750-gas-block.port_from_rear","superlative-750-gas-block.height_above_bore","superlative-750-gas-block.length","superlative-750-gas-block.foot_below_bore"],"inputs":{"superlative-750-gas-block.foot_below_bore":0.57,"superlative-750-gas-block.height_above_bore":0.813,"superlative-750-gas-block.length":1,"superlative-750-gas-block.port_from_rear":0.271},"tolerance":0.003,"photo":"references/superlative-750-gas-block 3b5e9fb65021 (Primary Arms, SABO-DI-750SM: the right side straight on, the adjuster at the right, 2200 x 1466)","method":"luminance < 128, largest piece, holes filled; frame from the reviewed holes rear_top, front_top, rear_foot, front_foot (664.9 px/in, rms 0.005 in over 4 points); origin at the photo's frame; Douglas-Peucker at 0.003 in with the extremes kept: 33 points (IoU 0.997 with the full outline); the frame is the body's four corners as the silhouette has them (its two faces on the boss's rows and on the foot's, its top and its flat), at the sellers' length and the drawing's two heights: the length and the height fit one scale within 1%; checks: x_max 0.953 ± 0.004; median row width in y [-0.5, -0.2] (0.994–1.014) 1.005 ± 0.006 (tools/trace.py)","via":"harvest","note":"Its right side: the body square, the adjustment screw standing out of the front face with the tab's end under it. Nothing is built from it; the section and the ledger's places along the block are."}},"gaps":[{"what":"Its weight","need":"Six sellers say 1.68 oz and Wing Tactical's table 1.80 oz for the same number; none says what was on the scale. The model as 416 stainless, with its screws and nothing cut inside, is 1.84 oz"},{"what":"The gas tube's hole against the standard","need":"It reads 0.685 in above the bore on the rear photo, 0.060 over the Army's .625; the maker's instruction sheet (on its own site, which refuses the reader, and at Brownells, which refused too) would say which tube it takes and whether the hole is meant high"},{"what":"The set screws' places along the foot","need":"A view square to the underside of the .750 set-screw block (the one on file is oblique, of a stainless block whose diameter isn't said)"},{"what":"A camera for the two side photos","need":"They are close shots from above (the lens some 4 in off by the tab's two thicknesses). A camera fitted to the pin's hole's two rims and the block's edges in each would give every feature on the sides its own correction: the pocket's height (± 0.025 in), the pad's length and the pin's rear end (each read some 5% long, inside their ±)"},{"what":"The lasered logo and lettering on the right side","need":"Primary Arms' right side photo shows them whole (the mark is one bright piece 0.52 in long with four dark islands in it; 'suparms.com' and the patent's number under it; the lot's number is the one block's). They are on the face nearest a close lens in a photo from above: they read some 10% large and 0.07 in low. With the camera for that photo fitted (the gap above) the mark is traced through it onto the ring's surface as its own material slot, as BCM's star is"},{"what":"The detent's tab across the face and the adjuster's shank","need":"A close view of the front from above or below: whether the tab is one thickness, the four flats on the adjuster's neck that the detent bears on (Primary Arms' six are the two sides, the two ends and two three-quarters)"},{"what":"How far the adjuster stands out at a working setting","need":"The maker's sheet: Wing Tactical says 18 clicks from closed is full pressure and 30 more are to be had, four to the turn; the thread's pitch isn't published, so the travel isn't known. Drawn closed, as shipped and as photographed"}]},"surefire-m340c-mini-scout-light-pro":{"id":"surefire-m340c-mini-scout-light-pro","name":"Mini Scout Light Pro","manufacturer":"SureFire","sku":"M340C-BK-PRO","url":"https://www.surefire.com/mini-scout-light-pro/","category":"light","description":"SureFire's 3-volt Scout Light Pro with the Z68 click tail cap: 500 lumens on the one 123A it comes with. Its Low-Profile Mount pivots, and it comes with a mount for a MIL-STD-1913 rail (the M-1913-S) and one for M-LOK (the M-MLOK-S). Black (M340C-BK-PRO) and tan (M340C-TN-PRO).","weight":"surefire-m340c-mini-scout-light-pro.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":[0,0,0],"note":"On the rail's top at the middle of the Picatinny mount's clamp (the rail's centre line across, the middle of its plate along), +x toward the lens, +y up off the rail. The body's axis is at z = {.rail_centre_below_axis}, y = {.axis_above_mount}."},"mlok":{"origin":["({.barrel_rear_x} + {.barrel_front_x}) / 2 - ({.clamp_rear_x} + {.clamp_front_x}) / 2","{.axis_above_mount} + {.mlok_base_width} / 2","{.rail_centre_below_axis} - {.pivot_centre_below_axis} - {.mlok_pivot_above_face}"],"x":[1,0,0],"y":[0,0,1],"note":"The middle of the M-LOK mount's two screws on its mounting face, +y out of the face toward the body (the part's +z: the body stands over the base, as SureFire photographs the Dual Fuel on it). The screws are taken as centred on the pivot barrel's length, and the barrel as standing over the base's long edge, as the Dual Fuel's are."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":"=({.clamp_front_x} - {.clamp_rear_x}) / 2","clamp_front":"=({.clamp_front_x} - {.clamp_rear_x}) / 2"},"flips":false,"note":"The M-1913-S: one clamp 0.59 in long, a fixed hook under the pivot and a moving jaw drawn up by a slotted screw (the manual: \"Use a flathead screwdriver to tighten or loosen mount screw\"). It is drawn with the body to +z, as SureFire's photos of this light have it."},"mlok":{"type":"mlok","role":"accessory","anchor":"mlok","params":{"lugs":"={.lugs}","reach_inside":"={.reach_inside}"},"flips":false,"note":"The M-MLOK-S (the manual: \"M-MLOK-S: See Magpul instructions enclosed\"; those instructions aren't on file): two screws with T-nuts about 0.64 in apart, both in one slot, as worked out for the Dual Fuel. How far its nuts reach inside isn't published, so that check reads as unmade."}},"materials":{"body":{"label":"Body and mount","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized_matte","color":"placeholder-black","sku":"M340C-BK-PRO","source":"https://www.surefire.com/mini-scout-light-pro/"},"tan":{"label":"Tan","finish":"anodized_matte","color":"surefire-tan","sku":"M340C-TN-PRO","source":"https://www.surefire.com/mini-scout-light-pro/"}},"default":"black","note":"Hard-anodized aluminium (\"FINISH Mil-Spec Hard Anodized\"; the product information sheet: \"FINISH Hard Anodized (MIL-A-8625 Type III, Class 2)\"; SureFire's page lists the two: \"PART NO. UPC M340C-BK-PRO 084871329224 M340C-TN-PRO 084871329231\"). The bezel, the head, the tube, the tail cap and both mounts are the one anodize in each colour (Primary Arms' photographs of a black and of a tan unit). Drawn matte, as the Dual Fuel is. Black is the placeholder the optics use, not matched (a black anodize's brightness in a photo is reflection). Tan is the Dual Fuel's preset (`surefire-tan`, fitted to Sportsman's Warehouse's photographs of a tan M640DF, #a18c78 and #a69482 on lit flats), reused, not fitted again: Primary Arms' photographs of the tan M340C read #98816a on the tube and #9a8065 on the head where they are lit (and #85725e from behind, less lit), the same tan some ten levels darker, which is what two sellers' studios differ by. SureFire's own picture of the tan light is a render in a pale grey (#c4bdb3), as its picture of the tan Dual Fuel is."},"lens":{"label":"Lens","finish":"glass","recolorable":false,"color":"glass-clear"},"button":{"label":"Tail cap button","finish":"rubber","recolorable":false,"color":"placeholder-polymer-black","note":"The Z68 tail cap's rubber boot inside its shroud: black on the black light (Primary Arms' M340C-BK-PRO_01, from behind) and on the tan one (Primary Arms' M340C-TN-PRO_01)."},"hardware":{"label":"Screws","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The pivot screw's slotted head ahead of the front ear, the Picatinny mount's slotted screw under its jaw and the M-LOK mount's two socket screws: dark steel on both colours of light (black against the tan body and mount in Primary Arms' photograph of the tan light, M340C-TN-PRO_00). Their finish isn't named on a page on file."}},"components":{},"geometry":{"components":{"body":"surefire-m340c-mini-scout-light-pro.body.glb","rail_clamp":"surefire-m340c-mini-scout-light-pro.rail_clamp.glb","mlok":"surefire-m340c-mini-scout-light-pro.mlok.glb"},"approximations":["The body is turned from SureFire's own outline drawing of it (the product information sheet's BODY SPECS, vector line art read at 600 dpi), its lengths by the published 4.1 in between the end faces, to which the drawing's dimension lines are drawn. At that scale the bezel reads 1.113 in, 1.1% under the published 1.125 (inside the length's own ±0.05): the model's bezel is the drawing's. The drawing has the mount's plate across the body's lower half between the bands, so the body is turned from its top edge alone, about the axis the ring's two edges put in the middle.","The ring behind the bezel has six flats, each a plane that leans 3 degrees (deeper at its rear), from the drawing; one is taken as facing +y (a flat faces the lens in SureFire's profile photo too), since the head's roll on the body isn't fixed. The Z68 shroud has its four holes, 45 degrees from the flats. Not drawn: the diamond knurl on the tail cap's ring (drawn as the round band its outline is), the bezel's scalloped front rim (the outline's notches at the front face are turned as rings), the engraving.","The lens is a disc 0.8 of the bezel across, set behind the bezel's front face by .lens_recess (an assumption, as the Dual Fuel's), and the tail cap's shroud is bored 0.8 of its diameter across, four fifths as deep as it runs straight: how wide the glass is and the hollow round the button aren't sourced. The button is a rubber skin on that hollow's floor, in its own material: its dome isn't drawn.","The mount swivels, and is drawn where SureFire photographs it on this light: the Picatinny mount hanging straight, the body beside the rail, its axis at the M-1913-S's pivot height over the rail (the Dual Fuel's 0.19 in, the most it can be) and 1.08 in from the rail's centre line (this light's pivot, 0.61 in under its axis, and the M-1913-S's rail centre 0.47 under its pivot). On the M-LOK mount the body stands over the base, the pivot the M-MLOK-S's 0.4 in off the face (give or take 0.1).","The pivot's two ears and the pivot screw's head are traced from SureFire's right profile photo of this light, placed on the drawing's outline by five of the body's steps; across the body they are round about the pivot at the barrel's diameter (as the rear three-quarter views show them). The Picatinny mount's plate is this light's own photo of it, hanging square to the lens; across the body its plate is the Dual Fuel's: tangent to its barrel on the SF side and 0.22 in thick, riding clear of the rail's top, its jaws lips either side of the rail reaching 0.1 in below its top, their inner faces the rail's own head in section that far, its recoil bar a plain bar across the rail down to the rail's top. The mount screw's head stands out of the jaw's end, centred across the plate (assumed). The hooks' 45 degree faces, the bar's reach into a slot, the screws' slots and the SF mark aren't drawn.","This light's photo has the M-1913-S's barrel 0.60 in long between the ears and its plate's end 1.01 in below the pivot; the Dual Fuel's photos read 0.553 and 0.969 for the same mount. This light's are drawn, and both are in the ledger (.barrel_front_x, .jaw_bottom_below_axis).","The M-LOK mount is the Dual Fuel's: plain shapes at sizes read as ratios from three-quarter photos of the M-MLOK-S (its screws 0.64 in apart, its base 0.40 in wide, round-ended about the screws): a base, the barrel over one long edge and a web between them, the counterbores half the base deep with a plain disc of a screw head in each (assumed); the web's cut-outs and the T-nuts aren't drawn.","A tape switch, which some Scout lights take, isn't part of this product (it has the Z68 click tail cap) and nothing of a cable is drawn."],"ledger":["surefire-m340c-mini-scout-light-pro.length","surefire-m340c-mini-scout-light-pro.head_diameter","surefire-m340c-mini-scout-light-pro.body_diameter","surefire-m340c-mini-scout-light-pro.ring_diameter","surefire-m340c-mini-scout-light-pro.rail_centre_below_axis","surefire-m340c-mini-scout-light-pro.axis_above_mount","surefire-m340c-mini-scout-light-pro.pivot_centre_below_axis","surefire-m340c-mini-scout-light-pro.clamp_thickness","surefire-m340c-mini-scout-light-pro.jaw_bottom_below_axis","surefire-m340c-mini-scout-light-pro.mlok_screw_spacing","surefire-m340c-mini-scout-light-pro.mlok_base_width","surefire-m340c-mini-scout-light-pro.mlok_pivot_above_face","surefire-m340c-mini-scout-light-pro.lens_recess"]},"profiles":{"side":{"plane":"xy","origin":"the tail cap's rear face, on the body's axis","offset":{},"points":[[0,0.477],[0,-0.001],[0,-0.477],[0.009,-0.493],[0.021,-0.496],[0.406,-0.496],[0.527,-0.396],[0.553,-0.396],[0.561,-0.381],[0.598,-0.381],[0.606,-0.396],[0.851,-0.396],[0.86,-0.381],[0.894,-0.381],[0.903,-0.396],[0.99,-0.396],[1,-0.386],[1.015,-0.394],[1.313,-0.394],[1.318,-0.389],[1.325,-0.396],[1.325,-0.279],[1.333,-0.272],[1.339,-0.274],[1.325,-0.248],[1.316,-0.205],[1.323,-0.198],[1.895,-0.198],[1.902,-0.205],[1.894,-0.243],[1.881,-0.273],[1.887,-0.269],[1.894,-0.276],[1.895,-0.397],[1.902,-0.391],[1.907,-0.394],[2.226,-0.394],[2.253,-0.42],[2.317,-0.42],[2.324,-0.428],[2.324,-0.492],[2.329,-0.495],[2.48,-0.495],[2.51,-0.508],[2.534,-0.543],[2.558,-0.557],[2.887,-0.557],[2.899,-0.547],[2.947,-0.547],[2.95,-0.544],[2.972,-0.574],[3,-0.587],[3.253,-0.587],[3.273,-0.579],[3.293,-0.551],[3.301,-0.557],[4.064,-0.556],[4.1,-0.5],[4.1,-0.392],[4.07,-0.309],[4.064,-0.274],[4.064,-0.23],[4.072,-0.177],[4.1,-0.085],[4.1,0.083],[4.069,0.197],[4.064,0.225],[4.064,0.276],[4.077,0.332],[4.1,0.39],[4.1,0.499],[4.061,0.556],[3.298,0.556],[3.293,0.551],[3.272,0.579],[3.249,0.587],[3.006,0.587],[2.978,0.579],[2.952,0.544],[2.899,0.546],[2.889,0.556],[2.556,0.556],[2.531,0.538],[2.513,0.511],[2.489,0.496],[2.329,0.495],[2.324,0.49],[2.324,0.428],[2.319,0.422],[2.254,0.42],[2.226,0.392],[1.905,0.392],[1.885,0.373],[1.335,0.373],[1.315,0.392],[1.011,0.392],[0.998,0.384],[0.99,0.396],[0.903,0.396],[0.894,0.381],[0.86,0.381],[0.851,0.396],[0.606,0.396],[0.598,0.381],[0.561,0.381],[0.554,0.388],[0.555,0.396],[0.525,0.396],[0.408,0.495],[0.017,0.495],[0.005,0.489]],"scaleRefs":["surefire-m340c-mini-scout-light-pro.length"],"inputs":{"surefire-m340c-mini-scout-light-pro.length":4.1},"tolerance":0.003,"photo":"references/surefire-m340c-mini-scout-light-pro fc4b86cba85b (SureFire's product information sheet (M340C-PRO.pdf), page 2, BODY SPECS: the outline drawing, rendered at 600 dpi)","method":"luminance < 128, inside [60, 280, 2620, 1100], 1 boxes excluded, closing ×2, largest piece, holes filled, inset 2 px (half the outline's stroke); scale from surefire-m340c-mini-scout-light-pro.length = 4.1 in (x-extent 2487 px → 606.6 px/in); origin at x min, y center of the outline; Douglas-Peucker at 0.003 in with the extremes kept: 111 points (IoU 0.999 with the full outline); checks: height (tooth tops, max over 0.05 in windows) along x [3.5, 3.95] 1.113 ± 0.014 in vs surefire-m340c-mini-scout-light-pro.head_diameter 1.125 ± 0.0005 (confirmed): agrees (tools/trace.py)","via":"harvest","note":"The drawing's top edge is the turned body's everywhere; its lower edge is the body's but between the two bands, where the M-1913-S's plate is drawn across it (the outline there is the plate's top block). The bezel's ring has scallops, drawn in this view as three facets."},"clamp":{"plane":"xy","origin":"the photo's frame","offset":{},"points":[[1.323,-0.443],[1.325,-1.549],[1.348,-1.589],[1.377,-1.61],[1.501,-1.612],[1.504,-1.618],[1.825,-1.615],[1.839,-1.609],[1.866,-1.585],[1.88,-1.56],[1.885,-1.515],[1.885,-1.32],[1.891,-1.281],[1.89,-0.971],[1.895,-0.797],[1.899,-0.784],[1.912,-0.783],[1.91,-0.43],[1.899,-0.43],[1.896,-0.441],[1.327,-0.439]],"scaleRefs":["surefire-m340c-mini-scout-light-pro.shroud_cone_x","surefire-m340c-mini-scout-light-pro.clamp_rear_x","surefire-m340c-mini-scout-light-pro.clamp_front_x","surefire-m340c-mini-scout-light-pro.head_step_x","surefire-m340c-mini-scout-light-pro.ring_front_x"],"inputs":{"surefire-m340c-mini-scout-light-pro.clamp_front_x":1.902,"surefire-m340c-mini-scout-light-pro.clamp_rear_x":1.317,"surefire-m340c-mini-scout-light-pro.head_step_x":2.324,"surefire-m340c-mini-scout-light-pro.ring_front_x":3.28,"surefire-m340c-mini-scout-light-pro.shroud_cone_x":0.457},"tolerance":0.003,"photo":"references/surefire-m340c-mini-scout-light-pro b1f3e5726acc (SureFire's gallery, M340C-BK-PRO-profileR: the light on its Picatinny mount, right side, on white, 1500 x 1500)","method":"luminance < 235, inside [487, 712, 696, 1150], 1 boxes excluded, largest piece, holes filled; frame from the reviewed holes cone, clamp_rear, clamp_front, head_step, ring_front (355.3 px/in, rms 0.009 in over 5 points); origin at the photo's frame; Douglas-Peucker at 0.003 in with the extremes kept: 21 points (IoU 0.994 with the full outline); checks: −y_min 1.618 ± 0.007 in vs surefire-m340c-mini-scout-light-pro.jaw_bottom_below_axis 1.642 ± 0.01 (conflict): DISAGREES; x_min in y [-1.5, -0.9] 1.324 ± 0.006; x_max in y [-1.5, -0.9] 1.893 ± 0.008 (tools/trace.py)","via":"harvest","note":"The mount's barrel on the pivot at the top, between the ears; the plate with the SF mark below it, narrowing under the barrel; the moving jaw at its end, its split line across. Seen square on: the plate hangs in the plane of the body's axis and the pivot."},"lug_front":{"plane":"xy","origin":"the photo's frame","offset":{},"points":[[1.92,-0.403],[1.922,-0.784],[2.172,-0.781],[2.182,-0.768],[2.188,-0.701],[2.188,-0.557],[2.179,-0.549],[2.185,-0.529],[2.182,-0.453],[2.172,-0.44],[2.163,-0.438],[2.037,-0.438],[2.034,-0.401]],"scaleRefs":["surefire-m340c-mini-scout-light-pro.shroud_cone_x","surefire-m340c-mini-scout-light-pro.clamp_rear_x","surefire-m340c-mini-scout-light-pro.clamp_front_x","surefire-m340c-mini-scout-light-pro.head_step_x","surefire-m340c-mini-scout-light-pro.ring_front_x"],"inputs":{"surefire-m340c-mini-scout-light-pro.clamp_front_x":1.902,"surefire-m340c-mini-scout-light-pro.clamp_rear_x":1.317,"surefire-m340c-mini-scout-light-pro.head_step_x":2.324,"surefire-m340c-mini-scout-light-pro.ring_front_x":3.28,"surefire-m340c-mini-scout-light-pro.shroud_cone_x":0.457},"tolerance":0.003,"photo":"references/surefire-m340c-mini-scout-light-pro b1f3e5726acc (SureFire's gallery, M340C-BK-PRO-profileR: the light on its Picatinny mount, right side, on white, 1500 x 1500)","method":"luminance < 235, inside [699, 702, 800, 845], largest piece, holes filled; frame from the reviewed holes cone, clamp_rear, clamp_front, head_step, ring_front (355.3 px/in, rms 0.009 in over 5 points); origin at the photo's frame; Douglas-Peucker at 0.003 in with the extremes kept: 13 points (IoU 0.990 with the full outline); checks: −y_min 0.784 ± 0.005; x_max 2.188 ± 0.009 in vs surefire-m340c-mini-scout-light-pro.screw_head_front_x 2.178 ± 0.006 (provisional): agrees (tools/trace.py)","via":"harvest","note":"The front ear and the pivot screw's slotted head ahead of it, against it."},"lug_rear":{"plane":"xy","origin":"the photo's frame","offset":{},"points":[[0.972,-0.559],[0.972,-0.663],[0.979,-0.676],[0.989,-0.672],[0.989,-0.759],[1.002,-0.783],[1.311,-0.788],[1.315,-0.787],[1.313,-0.403],[0.99,-0.403],[0.988,-0.54]],"scaleRefs":["surefire-m340c-mini-scout-light-pro.shroud_cone_x","surefire-m340c-mini-scout-light-pro.clamp_rear_x","surefire-m340c-mini-scout-light-pro.clamp_front_x","surefire-m340c-mini-scout-light-pro.head_step_x","surefire-m340c-mini-scout-light-pro.ring_front_x"],"inputs":{"surefire-m340c-mini-scout-light-pro.clamp_front_x":1.902,"surefire-m340c-mini-scout-light-pro.clamp_rear_x":1.317,"surefire-m340c-mini-scout-light-pro.head_step_x":2.324,"surefire-m340c-mini-scout-light-pro.ring_front_x":3.28,"surefire-m340c-mini-scout-light-pro.shroud_cone_x":0.457},"tolerance":0.003,"photo":"references/surefire-m340c-mini-scout-light-pro b1f3e5726acc (SureFire's gallery, M340C-BK-PRO-profileR: the light on its Picatinny mount, right side, on white, 1500 x 1500)","method":"luminance < 235, inside [355, 702, 484, 845], largest piece, holes filled; frame from the reviewed holes cone, clamp_rear, clamp_front, head_step, ring_front (355.3 px/in, rms 0.009 in over 5 points); origin at the photo's frame; Douglas-Peucker at 0.003 in with the extremes kept: 11 points (IoU 0.979 with the full outline) (tools/trace.py)","via":"harvest","note":"The rear ear, under the rear band; a small socket screw shows in its side, and the pivot screw's end a little behind it."}},"gaps":[{"what":"Whether the 3.65 oz counts a mount, and what Primary Arms' 4.1 oz counts","need":"SureFire says \"W/ BATTERIES\" only; each mount sold apart is 1.6 oz. A page that weighs the light and its mounts apart"},{"what":"Body diameters other than the bezel's, the mounts' sizes, how many M-LOK slots the mount takes: none is published","need":"The body's are read on SureFire's own drawing; the mounts' across the body are the Dual Fuel's coarse ratios from three-quarter photos. A square end view of each mount, or SureFire's drawing of the mounts"},{"what":"The M-1913-S's barrel and plate read 0.05 and 0.04 in longer on this light's photo than on the Dual Fuel's","need":"A square photo of the M-1913-S alone with something of known size, or SureFire's drawing of it"},{"what":"How far the M-LOK mount's nuts reach inside the handguard (reach_inside)","need":"The Magpul instructions the manual says are enclosed with the M-MLOK-S"},{"what":"Tan rests on the Dual Fuel's match to one seller's photographs; Primary Arms' photographs of the tan M340C read some ten levels darker","need":"A colour fit (`make color-match`) to Primary Arms' photographs of the M340C, if the two lights' tans are to be told apart"},{"what":"How far the mount swivels","need":"SureFire's pages say only that it lets the user optimize the light's position relative to the rail. The build draws one position"},{"what":"Overall width","need":"Not published, and it changes with the swivel"}]},"surefire-procomp-556":{"id":"surefire-procomp-556","name":"ProComp 556 Muzzle Brake","manufacturer":"SureFire","sku":"PROCOMP-556-1/2-28","url":"https://www.primaryarms.com/surefire-procomp-muzzle-brake-1-2x28-procomp556-1-2-28","category":"muzzle_device","description":"A stand-alone muzzle brake: two large windows through each side, flat port faces, two shallow pockets on the top and two on the bottom with a land between each pair, the top pair each drilled with a hole, and blind pilot holes at 3, 6 and 9 o'clock for tuning or for pinning. No suppressor mounts on it.","weight":"surefire-procomp-556.weight","cartridge":{"takes":["5.56 NATO",".223 Rem"],"stated":"Caliber: 5.56 mm (.223 caliber)","source":"https://www.primaryarms.com/surefire-procomp-muzzle-brake-1-2x28-procomp556-1-2-28 (its feature list, as cached: harvest.quote; Redcon1: \"Fits: .223 / 5.56\")"},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"thread":{"origin":[0,0,0],"note":"Device frame: on the bore axis at the barrel's shoulder, +x toward the muzzle. The device's rear face bears on the shoulder (no washer drawn: see the length's note in the ledger)."},"front":{"origin":["{.length}",0,0],"note":"The device's front face: where the build's overall length ends."}},"interfaces":{"thread":{"type":"muzzle_thread","role":"device","anchor":"thread","params":{"thread":"1/2-28"},"flips":false,"note":"Its number names its thread, PROCOMP-556-1/2-28 (Redcon1: \"Thread: 1/2 x 28 TPI\"; Primary Arms: \"Thread Pattern 1/2 X 28\"). SureFire, as Piasa Armory and Midwest Gun Works reprint it: \"ProComp 556 fits M4/M16 weapons and variants with 1/2-28 muzzle threads\", \"Installation requires no permanent modifications for M4 / M16 / AR15-type weapons\". No source gives how long a barrel thread it takes: no thread_length. How it is timed, none of SureFire's text says but its 6 o'clock pilot hole, which \"allows indexing the adapter at bottom dead center\" (Primary Arms). It takes no suppressor: SureFire, as Midwest Gun Works, Redcon1, AR15Discounts, Mile High and Piasa Armory reprint it, \"NOTE: SureFire ProComp muzzle brakes are stand-alone muzzle devices and do not serve as mounts/adapters for any SureFire Fast-Attach sound suppressors.\" (SureFire's sheet is headed \"MUZZLE BRAKE STAND-ALONE (NON-SOCOM ADAPTER)\" by the discovery's reading; not on file); Primary Arms: \"NOTE: Not compatible with SureFire Fast-Attach suppressors\", \"Suppressor Mount Non-Mount\". So no suppressor_mount and no suppressor_seat: the catalog's SOCOM556-RC2 goes on SureFire's WARCOMP or 3- and 4-prong adapters, not on this."}},"materials":{"body":{"label":"Muzzle brake","finish":"nitride","recolorable":false,"color":"steel-nitride-black","note":"One colour, black. SureFire's sheet as KYGunCo reprints it: \"FINISH: Nitride Finish\"; Primary Arms: \"Melonite finish\" (\"Finish Melonite\", \"Material Steel\"); SureFire, as Piasa Armory reprints it: \"heat-treated steel, precision machined from USA mill-certified bar stock\", \"Black nitride coating provides maximum protection against harsh environmental conditions\". Salt-bath nitride is the catalog's `nitride` (a polished black), drawn in the shared black for it and not fitted: Primary Arms' photographs read 18 to 22 of 255 on the faces square to the lens and 130 where the light lies along a face, which is the studio's light, not the coat. The lasered PROCOMP-556-SUREFIRE round the collar isn't drawn. No other colour is sold: PROCOMP-762-5/8-24 is the 7.62 model, another product."}},"components":{},"geometry":{"model":"surefire-procomp-556.glb","components":{},"approximations":["Every size but the length, the weight and the width is read on Primary Arms' two straight photographs of PROCOMP-556-1/2-28 standing, a quarter turn apart (from its left side and from below), its stations scaled by the 2.5 in length and its sizes across by the 0.864 in width.","Turned: one diameter from the rear taper to the front face (the lands at 12 and 6 o'clock stay round the whole length), a straight cone at the rear down to the rear face, three grooves round the collar. Then cut: the two port flats from 1.19 in forward, with a round run-out at their rear end; two windows straight through from side to side, square-walled, with round corners; two shallow pockets on the top and two on the bottom, each a flat floor turned 24 degrees out toward its own side with round ends, a land between each pair; the bore and the thread.","The top pockets are drawn as the bottom ones, read square on: no view on file faces the top square on, and the three-quarter views show the same two pockets and land there.","The windows are drawn on the axis: they read 0.012 in above it in the side view, as everything on that face does by the photo's turn about the axis. SureFire's \"offset porting\" is the two top ports, as its patent for this product says (US 7,954,414: offset to either side of the top, one further than the other): drawn at one station, as the patent's FIG. 4 has them, each in its pocket's middle, 25 degrees either side of the top; how much further one is offset than the other no view on file shows.","Inside the windows SureFire's pictures show slanted faces (its \"Impulse Diffusion design\"): not drawn. The walls between the windows and ahead of them are square to the axis, with the bore through them.","The pilot holes at 3 and 9 o'clock are drawn blind, as shallow as a spot drill; the pin-and-weld hole at 6 through the collar to the thread; the top ports down into the first chamber. How deep the blind ones go isn't sourced.","Inside, between the thread and the rear window, the high-pressure first chamber the top ports vent (the patent's FIG. 6), drawn as wide as the thread's minor diameter, ending in a cone and a wall short of the window, by the patent figure's proportions: no view on file looks into it.","The thread is the Army barrel's 1/2-28 cut as a helix, as deep as the Army compensator's bore, and the hole ahead of it the SOCOM 3-prong's: neither is sourced for this device.","No washer is drawn: one seller says a crush washer is in the box, and no photo or other page shows or says one.","Edges broken at 0.006 in. The front face's turned rings and the lasered marks aren't drawn."],"ledger":["surefire-procomp-556.overall_length","surefire-procomp-556.length","surefire-procomp-556.od","surefire-procomp-556.flats_across","surefire-procomp-556.window_height","surefire-procomp-556.pocket_tilt","surefire-procomp-556.top_right_hole_x","surefire-procomp-556.chamber_d","surefire-procomp-556.chamber_front_x","surefire-procomp-556.thread_depth","surefire-procomp-556.bore_d"]},"profiles":{"side":{"plane":"xy","origin":"the rear end of the outline (the rear face's near rim, 0.02 in behind the face's centre in this view from above), on the middle of the outline's height there: the bore axis","offset":{},"points":[[0,0.07],[0,0],[0,-0.072],[0.011,-0.206],[0.027,-0.286],[0.05,-0.348],[0.071,-0.37],[0.216,-0.41],[0.547,-0.414],[0.558,-0.407],[0.554,-0.402],[0.559,-0.397],[0.58,-0.397],[0.597,-0.414],[0.629,-0.414],[0.638,-0.407],[0.634,-0.402],[0.639,-0.397],[0.654,-0.397],[0.664,-0.399],[0.677,-0.414],[0.707,-0.414],[0.718,-0.407],[0.721,-0.397],[0.744,-0.397],[0.755,-0.412],[0.776,-0.416],[2.177,-0.422],[2.434,-0.42],[2.462,-0.415],[2.466,-0.404],[2.45,-0.246],[2.455,-0.241],[2.46,-0.246],[2.46,-0.261],[2.479,-0.31],[2.485,-0.299],[2.496,-0.198],[2.5,-0.063],[2.5,0.105],[2.489,0.282],[2.481,0.312],[2.474,0.309],[2.46,0.244],[2.455,0.239],[2.45,0.244],[2.466,0.4],[2.46,0.415],[2.293,0.414],[2.252,0.422],[0.766,0.418],[0.745,0.399],[0.721,0.399],[0.717,0.41],[0.7,0.418],[0.681,0.416],[0.665,0.399],[0.637,0.399],[0.631,0.412],[0.606,0.418],[0.578,0.397],[0.559,0.397],[0.553,0.41],[0.532,0.418],[0.424,0.41],[0.323,0.41],[0.317,0.416],[0.308,0.41],[0.216,0.41],[0.073,0.37],[0.051,0.35],[0.03,0.299],[0.019,0.249]],"scaleRefs":["surefire-procomp-556.overall_length"],"inputs":{"surefire-procomp-556.overall_length":2.5},"tolerance":0.004,"photo":"references/surefire-procomp-556 df201d3f2cee (Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, seen square from its left side (the 9 o'clock port face to the lens, the top to the right), on white)","method":"luminance < 200, inside [850, 80, 1380, 1440], closing ×2, largest piece, holes filled; rotated -90.0° as declared; scale from surefire-procomp-556.overall_length = 2.5 in (x-extent 1313 px → 525.2 px/in); origin at x min, y center of the outline; Douglas-Peucker at 0.004 in with the extremes kept: 73 points (IoU 0.996 with the full outline); The x-extent runs from the rear face's near rim to the front face's far rim (the ellipses of the two end faces in this view from about 3.5 degrees above): 2% longer than between the faces' centres, so the outline's heights read 2% small on top of a black edge's thin reading on white, and the checks against the published width fail by that. The model is built from the ledger's figures, read row by row between the faces' centres and across as fractions of the collar's width (data/ledger/surefire-procomp-556.yaml), not from this outline.; checks: height 0.843 ± 0.018 in vs surefire-procomp-556.od 0.864 ± 0.0005 (corroborated): DISAGREES; height in x [0.5, 0.75] 0.832 ± 0.018 (tools/trace.py)","via":"harvest","note":"The muzzle to the right, the top up. The outline's height is the two lands' at 12 and 6 o'clock, full round from end to end; the two port windows, seen through, are filled."},"plan":{"plane":"xz","origin":"the rear end of the outline, on the bore axis","offset":{},"points":[[0,-0.001],[0,-0.019],[0.016,-0.234],[0.038,-0.328],[0.063,-0.369],[0.212,-0.412],[0.37,-0.416],[0.423,-0.41],[0.539,-0.416],[0.55,-0.413],[0.555,-0.398],[0.577,-0.398],[0.591,-0.41],[0.619,-0.414],[0.626,-0.408],[0.633,-0.411],[0.627,-0.401],[0.632,-0.396],[0.658,-0.398],[0.674,-0.41],[0.704,-0.416],[0.713,-0.411],[0.711,-0.405],[0.718,-0.398],[0.738,-0.396],[0.758,-0.412],[1.19,-0.412],[1.19,-0.373],[1.216,-0.351],[1.228,-0.367],[1.274,-0.327],[1.617,-0.327],[1.674,-0.341],[1.728,-0.371],[1.887,-0.371],[1.903,-0.369],[1.965,-0.333],[1.989,-0.327],[2.162,-0.323],[2.212,-0.331],[2.284,-0.367],[2.457,-0.367],[2.466,-0.36],[2.46,-0.256],[2.465,-0.251],[2.47,-0.256],[2.485,-0.293],[2.494,-0.236],[2.5,0.087],[2.488,0.29],[2.483,0.299],[2.47,0.27],[2.465,0.265],[2.46,0.27],[2.466,0.358],[2.461,0.367],[2.445,0.371],[2.282,0.369],[2.24,0.341],[2.196,0.323],[2.031,0.323],[1.989,0.337],[1.939,0.367],[1.905,0.361],[1.883,0.367],[1.756,0.367],[1.72,0.365],[1.674,0.335],[1.603,0.319],[1.338,0.317],[1.274,0.339],[1.224,0.382],[1.198,0.353],[1.183,0.374],[1.183,0.397],[1.194,0.416],[0.758,0.414],[0.738,0.396],[0.72,0.396],[0.698,0.416],[0.668,0.408],[0.658,0.396],[0.638,0.396],[0.615,0.416],[0.589,0.41],[0.573,0.396],[0.551,0.396],[0.546,0.401],[0.55,0.407],[0.535,0.416],[0.521,0.41],[0.399,0.41],[0.381,0.416],[0.286,0.416],[0.26,0.41],[0.208,0.41],[0.081,0.376],[0.052,0.36],[0.03,0.31],[0.012,0.216]],"scaleRefs":["surefire-procomp-556.overall_length"],"inputs":{"surefire-procomp-556.overall_length":2.5},"tolerance":0.004,"photo":"references/surefire-procomp-556 aa48bc88d85b (Primary Arms PROCOMP556-1-2-28_02: the device standing muzzle up, seen square from below (the two bottom pockets and the land between them to the lens, the 6 o'clock pin hole in the collar), on white)","method":"luminance < 200, inside [850, 110, 1340, 1400], closing ×2, largest piece, holes filled; rotated -90.0° as declared; scale from surefire-procomp-556.overall_length = 2.5 in (x-extent 1245 px → 498.0 px/in); origin at x min, y center of the outline; Douglas-Peucker at 0.004 in with the extremes kept: 100 points (IoU 0.996 with the full outline); The x-extent runs from the rear face's near rim to the front face's far rim (the ellipses of the two end faces in this view from about 3.5 degrees above): 2% longer than between the faces' centres, so the outline's heights read 2% small on top of a black edge's thin reading on white, and the checks against the published width fail by that. The model is built from the ledger's figures, read row by row between the faces' centres and across as fractions of the collar's width (data/ledger/surefire-procomp-556.yaml), not from this outline.; checks: height in x [0.3, 0.6] 0.831 ± 0.018 in vs surefire-procomp-556.od 0.864 ± 0.0005 (corroborated): DISAGREES; height in x [1.75, 1.85] 0.739 ± 0.016 in vs surefire-procomp-556.flats_across 0.774 ± 0.015 (conflict): DISAGREES (tools/trace.py)","via":"harvest","note":"Seen from below, so the rifle's right is at the top of the outline. The two port flats are its sides ahead of the collar, notched where the windows go through."}},"gaps":[{"what":"SureFire's own sheet: its photographs, its \"BODY SPECS 1.0 in\" and its exact wording","need":"the product information sheet (PROCOMP_PIS.pdf) saved by the user from their own browser: its host's robots.txt refuses the reader"},{"what":"The top, square on: where the two top ports stand round the top and how the top pockets end","need":"a photo square on the top (Primary Arms has the underside; its _00 and _01 see the top from a three-quarter angle)"},{"what":"Whether it comes with a crush washer, and how it is timed","need":"SureFire's sheet or manual for the ProComp; only Cheaper Than Dirt says \"Includes Crush Washer\""},{"what":"The inside: the thread's depth, the bore, the slanted faces in the windows, whether the top holes go through","need":"a section drawing (SureFire's patent-marking page lists patents for its brakes; none on file is tied to the ProComp), or photos straight into both ends and each window"},{"what":"Its length: 2.5 in on SureFire's sheet and two sellers, 2.67 in on Cheaper Than Dirt's page","need":"the maker's sheet itself, or a review's own measurement"}]},"surefire-scout-light-pro-dual-fuel":{"id":"surefire-scout-light-pro-dual-fuel","name":"Scout Light Pro Dual Fuel","manufacturer":"SureFire","sku":"M640DF-BK-PRO","url":"https://www.surefire.com/scout-light-pro-dual-fuel/","category":"light","description":"SureFire's 6-volt Dual Fuel Scout Light Pro with the Z68 click tail cap: 1,500 lumens on the SF18650 cell it comes with, 1,200 on two 123A. Its Low-Profile Mount pivots, and it comes with a cleat for a MIL-STD-1913 rail and one for M-LOK. Black (M640DF-BK-PRO) and tan (M640DF-TN-PRO).","weight":"surefire-scout-light-pro-dual-fuel.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":[0,0,0],"note":"On the rail's top at the middle of the Picatinny mount's clamp (the rail's centre line across, the middle of its plate along), +x toward the lens, +y up off the rail. The body's axis is at z = {.rail_centre_below_axis}, y = {.axis_above_mount}."},"mlok":{"origin":["({.barrel_rear_x} + {.barrel_front_x}) / 2 - ({.clamp_rear_x} + {.clamp_front_x}) / 2","{.axis_above_mount} + {.mlok_base_width} / 2","{.rail_centre_below_axis} - ({.pivot_top_below_axis} + {.ear_bottom_below_axis}) / 2 - {.mlok_pivot_above_face}"],"x":[1,0,0],"y":[0,0,1],"note":"The middle of the M-LOK mount's two screws on its mounting face, +y out of the face toward the body (the part's +z: the body stands over the base, as photographed). The screws are taken as centred on the pivot barrel's length, and the barrel as standing over the base's long edge. Since 2026-10-05 the middle of the two, not the rear one: a slot's position is its centre, and two nuts in one slot go one in each half of it."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":"=({.clamp_front_x} - {.clamp_rear_x}) / 2","clamp_front":"=({.clamp_front_x} - {.clamp_rear_x}) / 2"},"flips":false,"note":"The M-1913-S: one clamp 0.59 in long, a fixed hook and a moving jaw drawn up by a slotted screw. SureFire's photos show it fitted either way round on the pivot (the body to one side of the rail or the other); it is drawn as the newer ones have it, the body to +z."},"mlok":{"type":"mlok","role":"accessory","anchor":"mlok","params":{"lugs":"={.lugs}","reach_inside":"={.reach_inside}"},"flips":false,"note":"The M-MLOK-S: two screws with T-nuts about 0.64 in apart on an obround base, both in one slot (worked out from its photos: no page on file states a slot count). How far its nuts reach inside isn't published, so that check reads as unmade."}},"materials":{"body":{"label":"Body and mount","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized_matte","color":"placeholder-black","sku":"M640DF-BK-PRO","source":"https://www.surefire.com/scout-light-pro-dual-fuel/"},"tan":{"label":"Tan","finish":"anodized_matte","color":"surefire-tan","sku":"M640DF-TN-PRO","source":"https://www.surefire.com/scout-light-pro-dual-fuel/"}},"default":"black","note":"Hard-anodized aluminium (\"FINISH Mil-Spec Hard Anodized\"; SureFire's page lists the two: \"PART NO. UPC M640DF-BK-PRO 084871329262 M640DF-TN-PRO 084871329279\"). The bezel, the head, the tube, the tail cap and both mounts are the one anodize in each colour (the mounts are sold apart in black and in tan). Both colours are drawn matte (`anodized_matte`, since 2026-10-06): Primary Arms' photograph of the black light and Sportsman's Warehouse's of a tan one have a soft sheen and no bright line along the tube, which a receiver's satin anodize (`anodized`, what the black was drawn in until then) draws on a round part. Black is the placeholder the optics use, not matched (a black anodize's brightness in a photo is reflection); tan is matched to those photographs' tube. SureFire's tan is not one tone: on that unit the head's middle ring is some 18 levels darker than the tube; SureFire's own artwork of the tan light is a grey with a cream mount, Rifle Supply's copy of it a saturated tan all over. One tan is drawn."},"lens":{"label":"Lens","finish":"glass","recolorable":false,"color":"glass-clear"},"button":{"label":"Tail cap button","finish":"rubber","recolorable":false,"color":"placeholder-polymer-black","note":"The Z68 tail cap's rubber boot inside its shroud: black on the black light and on the tan one (Sportsman's Warehouse's photograph of the tan unit from behind; SureFire's rear view of the black one)."},"hardware":{"label":"Screws","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The pivot screw's head ahead of the front ear, the Picatinny mount's screw under its jaw and the M-LOK mount's two socket screws: dark steel on both colours of light (black against the tan body and mount in SureFire's and Rifle Supply's pictures of the tan light; a dark grey beside the black anodize in SureFire's picture of the M-MLOK-S). Their finish isn't named on a page on file."}},"components":{},"geometry":{"components":{"body":"surefire-scout-light-pro-dual-fuel.body.glb","rail_clamp":"surefire-scout-light-pro-dual-fuel.rail_clamp.glb","mlok":"surefire-scout-light-pro-dual-fuel.mlok.glb"},"approximations":["The body is turned from Rifle Supply's straight side photo of it alone (SureFire's artwork, 2000 px), heights by the bezel's published 1.125 in and lengths by the published 5.56 in between the end faces, which agree within 0.8% there; SureFire's newer left profile puts four of its steps within 0.003 in of that outline. It is drawn round all over: the flats on the bezel's ring, the knurling on the tail cap, the bezel's scalloped rim and the engraving aren't cut (the ring is as wide as that photo happens to see it, the rim ends square at the published length).","The lens is a disc 0.8 of the bezel across, set 0.08 in behind its front face, and the tail cap's shroud is bored 0.8 of its diameter across as deep as it runs straight: all four are assumed (how wide the glass is, how deep it sits and the hollow round the button aren't sourced). The button is a rubber skin on that hollow's floor, in its own material: its dome isn't drawn.","The mount swivels, and is drawn where SureFire photographs it. On the Picatinny mount the body stands beside the rail, its axis 1.12 in from the rail's centre line and 0.19 in above the rail's top; that height is a coarse ratio read from a three-quarter photo (the fixed hook's V against the barrel's end) and is the most it can be: it is less by however much more than 0.05 in a rail's corner lies below its top (the standard's figure for that isn't on file). On the M-LOK mount the body stands over the base, the pivot about 0.4 in off the face (give or take 0.1: no square view of that mount is on file).","The pivot's two ears and the mounts' outlines along the body are traced from SureFire's left profile. Across the body they are assumed: the ears and the screw's head round about the pivot at the barrel's diameter (as the rear three-quarter view shows them), the Picatinny mount's plate tangent to its barrel on the SF side and 0.22 in thick (a coarse ratio), riding clear of the rail's top; its jaws lips either side of the rail reaching 0.1 in below its top, their inner faces the rail's own head in section that far (MIL-STD-1913's upper faces and its widest, since 2026-10-12); its recoil bar (0.20 in wide in the right profile) a plain bar across the rail down to the rail's top. The mount screw's head stands out of the jaw's end at the size the left profile gives, centred across the plate (assumed). The hooks' 45 degree faces, the bar's reach into a slot, the screws' slots and the SF mark aren't drawn.","The M-LOK mount is plain shapes at sizes read as ratios from three-quarter photos (its screws 0.64 in apart, its base 0.40 in wide, round-ended about the screws): a base, the barrel over one long edge and a web between them. Its counterbores are cut at the diameter one photo gives (0.31 in), half the base deep (assumed). Each screw's head is a plain disc filling its counterbore and standing 0.7 of its depth (assumed), in the screws' own material, with no socket; the web's two cut-outs aren't drawn, and the T-nuts aren't either (they sit inside the handguard).","The tape switch some Scout lights are fitted with isn't part of this product (it has the Z68 click tail cap) and nothing of a cable is drawn."],"ledger":["surefire-scout-light-pro-dual-fuel.length","surefire-scout-light-pro-dual-fuel.head_diameter","surefire-scout-light-pro-dual-fuel.body_diameter","surefire-scout-light-pro-dual-fuel.rail_centre_below_axis","surefire-scout-light-pro-dual-fuel.axis_above_mount","surefire-scout-light-pro-dual-fuel.clamp_thickness","surefire-scout-light-pro-dual-fuel.rail_corner_below_pivot","surefire-scout-light-pro-dual-fuel.mlok_screw_spacing","surefire-scout-light-pro-dual-fuel.mlok_base_width","surefire-scout-light-pro-dual-fuel.mlok_pivot_above_face"]},"profiles":{"side":{"plane":"xy","origin":"the tail cap's rearmost point (its rim's near side), on the body's axis","offset":{},"points":[[0,0.127],[0.009,0.116],[0.009,-0.102],[0.003,-0.085],[0,0.045],[0,-0.128],[0.02,-0.428],[0.034,-0.476],[0.059,-0.5],[0.325,-0.501],[0.468,-0.402],[0.585,-0.403],[0.597,-0.391],[0.614,-0.389],[0.651,-0.389],[0.665,-0.406],[0.68,-0.411],[0.874,-0.406],[0.886,-0.404],[0.891,-0.392],[0.917,-0.39],[0.951,-0.39],[0.96,-0.401],[1.037,-0.401],[1.05,-0.38],[1.051,-0.35],[1.064,-0.428],[1.086,-0.447],[1.391,-0.447],[1.417,-0.428],[1.571,-0.425],[1.97,-0.427],[1.993,-0.446],[2.318,-0.447],[2.341,-0.425],[3.598,-0.426],[3.658,-0.482],[3.697,-0.488],[3.707,-0.523],[3.737,-0.536],[3.956,-0.537],[4.046,-0.56],[4.381,-0.561],[4.401,-0.549],[4.455,-0.547],[4.465,-0.565],[4.497,-0.589],[4.602,-0.592],[4.781,-0.587],[4.809,-0.553],[4.817,-0.562],[5.505,-0.564],[5.587,-0.561],[5.612,-0.55],[5.631,-0.532],[5.636,-0.464],[5.668,-0.402],[5.679,-0.355],[5.679,-0.248],[5.653,-0.132],[5.653,-0.011],[5.668,0.065],[5.69,0.138],[5.69,0.158],[5.682,0.279],[5.659,0.327],[5.622,0.445],[5.636,0.487],[5.639,0.526],[5.595,0.556],[5.567,0.562],[5.166,0.564],[4.823,0.562],[4.8,0.554],[4.775,0.588],[4.679,0.591],[4.492,0.589],[4.466,0.575],[4.446,0.547],[4.395,0.55],[4.387,0.558],[4.041,0.557],[3.995,0.543],[3.93,0.535],[3.729,0.533],[3.704,0.523],[3.695,0.485],[3.658,0.48],[3.598,0.421],[2.338,0.42],[2.318,0.44],[2.292,0.443],[1.993,0.441],[1.962,0.419],[1.457,0.421],[1.408,0.424],[1.391,0.443],[1.088,0.442],[1.071,0.433],[1.061,0.418],[1.051,0.343],[1.047,0.378],[1.031,0.397],[0.957,0.397],[0.948,0.389],[0.894,0.389],[0.871,0.403],[0.668,0.404],[0.648,0.384],[0.591,0.384],[0.582,0.396],[0.471,0.396],[0.322,0.496],[0.059,0.497],[0.037,0.479],[0.026,0.45],[0.011,0.357],[0.003,0.246],[0.006,0.13]],"scaleRefs":["surefire-scout-light-pro-dual-fuel.head_diameter","surefire-scout-light-pro-dual-fuel.length"],"inputs":{"surefire-scout-light-pro-dual-fuel.head_diameter":1.125,"surefire-scout-light-pro-dual-fuel.length":5.56,"surefire-scout-light-pro-dual-fuel.tailcap_diameter":0.989},"tolerance":0.004,"photo":"references/surefire-scout-light-pro-dual-fuel 5911a4468ee0 (Rifle Supply's gallery, SFM640DF-BK-PRO_2_HR: the body alone, straight side view on white, 2000 x 2000)","method":"luminance < 235, largest piece, holes filled; scale from surefire-scout-light-pro-dual-fuel.head_diameter = 1.125 in, the tube's own width column by column: 399.4 px over columns 1708–1752, 399.6 px over columns 1918–1955; a line through them (rms 0.27 px) changes +0.1% from column 1708 to 1955, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1000)/width, the lens's axis taken to meet the image at column 1000; 354.2 px/in there. The axis is the tube's centre line (tilt -0.20°, rms 0.06 px). Lengths then scaled by 1.0076 so that the end faces are surefire-scout-light-pro-dual-fuel.length = 5.56 in apart: at the tube's scale they read 5.518 (-0.8%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.070 in over radius 0.563 (rms 0.014), the rear end's rim sags 0.043 in over radius 0.494 (rms 0.001); origin at x min of the outline, on the tube's axis; Douglas-Peucker at 0.004 in with the extremes kept: 119 points (IoU 0.998 with the full outline); checks: height (tooth tops, max over 0.05 in windows) along x [2.5, 3.5] 0.845 ± 0.009 in vs surefire-scout-light-pro-dual-fuel.body_diameter 0.843 ± 0.006 (corroborated): agrees; height (tooth tops, max over 0.05 in windows) along x [0.08, 0.3] 0.997 ± 0.009 in vs surefire-scout-light-pro-dual-fuel.tailcap_diameter 0.989 ± 0.008 (corroborated): agrees (tools/trace.py)","via":"harvest","note":"Both edges are the turned body's (the pivot lug is behind it in this view). The bezel's ring has flats: its silhouette is the ring across them as this photo happens to see it."},"clamp":{"plane":"xy","origin":"the photo's frame","offset":{},"points":[[1.394,-0.836],[1.402,-0.898],[1.406,-0.901],[1.41,-0.982],[1.414,-0.986],[1.419,-1.289],[1.427,-1.312],[1.427,-1.411],[1.431,-1.415],[1.436,-1.565],[1.451,-1.595],[1.484,-1.62],[1.821,-1.619],[1.825,-1.615],[1.944,-1.61],[1.967,-1.599],[1.98,-1.585],[1.996,-1.558],[1.995,-1.543],[1.999,-1.539],[1.998,-1.374],[1.995,-1.37],[1.994,-1.263],[1.99,-1.259],[1.988,-0.833],[1.965,-0.83],[1.962,-0.471],[1.413,-0.474],[1.413,-0.832]],"scaleRefs":["surefire-scout-light-pro-dual-fuel.band_rear_x","surefire-scout-light-pro-dual-fuel.band_front_x","surefire-scout-light-pro-dual-fuel.head_step_x","surefire-scout-light-pro-dual-fuel.bezel_rear_x"],"inputs":{"surefire-scout-light-pro-dual-fuel.band_front_x":2.319,"surefire-scout-light-pro-dual-fuel.band_rear_x":1.078,"surefire-scout-light-pro-dual-fuel.bezel_rear_x":4.791,"surefire-scout-light-pro-dual-fuel.head_step_x":3.699},"tolerance":0.003,"photo":"references/surefire-scout-light-pro-dual-fuel 240f795d3e2a (SureFire's gallery, M640DF-BK-PRO-profileL: the light on its Picatinny mount, left side, on white, 1500 x 1500)","method":"luminance < 235, inside [960, 733, 1135, 1032], 2 boxes excluded, largest piece, holes filled; frame from the reviewed holes band_rear, band_front, head_step, bezel_rear (260.7 px/in, rms 0.003 in over 4 points); origin at the photo's frame; Douglas-Peucker at 0.003 in with the extremes kept: 29 points (IoU 0.998 with the full outline) (tools/trace.py)","via":"harvest","note":"The mount's barrel on the pivot at the top, the plate with the SF mark, the moving jaw under its split line. Seen square on: the plate hangs in the plane of the body's axis and the pivot."},"lug_front":{"plane":"xy","origin":"the photo's frame","offset":{},"points":[[1.963,-0.469],[1.965,-0.826],[2.086,-0.827],[2.09,-0.831],[2.105,-0.827],[2.115,-0.817],[2.118,-0.76],[2.124,-0.75],[2.145,-0.752],[2.149,-0.81],[2.153,-0.825],[2.163,-0.831],[2.293,-0.83],[2.305,-0.826],[2.318,-0.809],[2.322,-0.77],[2.325,-0.767],[2.325,-0.74],[2.318,-0.709],[2.325,-0.694],[2.324,-0.544],[2.321,-0.54],[2.32,-0.506],[2.313,-0.487],[2.299,-0.477],[2.161,-0.478],[2.152,-0.487],[2.148,-0.549],[2.142,-0.558],[2.131,-0.558],[2.125,-0.553],[2.126,-0.447],[1.969,-0.448]],"scaleRefs":["surefire-scout-light-pro-dual-fuel.band_rear_x","surefire-scout-light-pro-dual-fuel.band_front_x","surefire-scout-light-pro-dual-fuel.head_step_x","surefire-scout-light-pro-dual-fuel.bezel_rear_x"],"inputs":{"surefire-scout-light-pro-dual-fuel.band_front_x":2.319,"surefire-scout-light-pro-dual-fuel.band_rear_x":1.078,"surefire-scout-light-pro-dual-fuel.bezel_rear_x":4.791,"surefire-scout-light-pro-dual-fuel.head_step_x":3.699},"tolerance":0.003,"photo":"references/surefire-scout-light-pro-dual-fuel 240f795d3e2a (SureFire's gallery, M640DF-BK-PRO-profileL: the light on its Picatinny mount, left side, on white, 1500 x 1500)","method":"luminance < 235, inside [870, 727, 976, 830], 1 boxes excluded, largest piece, holes filled; frame from the reviewed holes band_rear, band_front, head_step, bezel_rear (260.7 px/in, rms 0.003 in over 4 points); origin at the photo's frame; Douglas-Peucker at 0.003 in with the extremes kept: 33 points (IoU 0.995 with the full outline) (tools/trace.py)","via":"harvest","note":"The front ear (0.16 in along the body) and the pivot screw's head ahead of it, a gap of 0.02 in between them where the screw's shank shows."},"lug_rear":{"plane":"xy","origin":"the photo's frame","offset":{},"points":[[1.031,-0.454],[1.031,-0.477],[1.035,-0.481],[1.036,-0.731],[1.04,-0.734],[1.044,-0.784],[1.056,-0.811],[1.077,-0.824],[1.315,-0.823],[1.319,-0.827],[1.361,-0.827],[1.388,-0.823],[1.392,-0.831],[1.413,-0.828],[1.409,-0.451]],"scaleRefs":["surefire-scout-light-pro-dual-fuel.band_rear_x","surefire-scout-light-pro-dual-fuel.band_front_x","surefire-scout-light-pro-dual-fuel.head_step_x","surefire-scout-light-pro-dual-fuel.bezel_rear_x"],"inputs":{"surefire-scout-light-pro-dual-fuel.band_front_x":2.319,"surefire-scout-light-pro-dual-fuel.band_rear_x":1.078,"surefire-scout-light-pro-dual-fuel.bezel_rear_x":4.791,"surefire-scout-light-pro-dual-fuel.head_step_x":3.699},"tolerance":0.003,"photo":"references/surefire-scout-light-pro-dual-fuel 240f795d3e2a (SureFire's gallery, M640DF-BK-PRO-profileL: the light on its Picatinny mount, left side, on white, 1500 x 1500)","method":"luminance < 235, inside [1120, 727, 1260, 830], 1 boxes excluded, largest piece, holes filled; frame from the reviewed holes band_rear, band_front, head_step, bezel_rear (260.7 px/in, rms 0.003 in over 4 points); origin at the photo's frame; Douglas-Peucker at 0.003 in with the extremes kept: 15 points (IoU 0.992 with the full outline) (tools/trace.py)","via":"harvest","note":"The rear ear, as long as the rear band it hangs from; a small screw's socket shows in its side."}},"gaps":[{"what":"SureFire's product information sheet (its outline drawing) and its manual","need":"Both are PDFs on store-fecqh2764q.mybigcommerce.com, whose robots.txt disallows everything, so neither is on file: a copy saved from a browser by the user, or the same documents on a host that allows the reader"},{"what":"Tan rests on one seller's photographs of one unit; SureFire's tan differs piece to piece (that unit's head ring is darker than its tube)","need":"A second seller's own photographs of a tan unit, not SureFire's artwork (which is a grey in one copy and a saturated tan in another)"},{"what":"Body diameter, the mounts' sizes, how many M-LOK slots the mount takes: none is published","need":"The body's is read from three photos by the bezel; the mounts' across the body are coarse ratios from three-quarter photos. A square end view of each mount, or SureFire's drawing, would settle them"},{"what":"How far the M-LOK mount's nuts reach inside the handguard (reach_inside)","need":"The sheet SureFire encloses for the M-MLOK-S (said to be Magpul's), or a figure for its T-nuts"},{"what":"Which batteries the 5.5 oz is with, and whether a mount is in it","need":"SureFire's page says \"w/ batteries\" only; each mount alone is 1.6 oz"},{"what":"How far the mount swivels, and that it goes either side","need":"SureFire's pages say only that it lets the user optimize the light's position relative to the rail; a reviewer (Shooting Illustrated) says nearly 180 degrees and right or left hand. The build draws one position"},{"what":"Overall width","need":"Not published, and it changes with the swivel"}]},"surefire-socom-3-prong":{"id":"surefire-socom-3-prong","name":"SOCOM 3-Prong Flash Hider","manufacturer":"SureFire","sku":"SF3P-556-1/2-28","url":"https://www.surefire.com/socom-3-prong-flash-hider/","category":"muzzle_device","description":"A three-tine flash hider that SureFire's SOCOM suppressors lock onto: three long tines ahead of a two-groove labyrinth seal, two wrench flats, and a flange with the indexing tab that is timed to the bottom with shims.","weight":"surefire-socom-3-prong.weight","cartridge":{"takes":["5.56 NATO",".223 Rem"],"stated":".223 Caliber (5.56mm) + 1/2-28 Thread Pitch","source":"https://www.surefire.com/socom-3-prong-flash-hider/ (the page's Model choice for SF3P-556-1/2-28, as cached: harvest.quote; Primary Arms: \"compatible with AR-15/M16 weapons and variants with 1/2x28 muzzle threads\")"},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"thread":{"origin":[0,0,0],"note":"Device frame: on the bore axis at the barrel's shoulder, +x toward the muzzle. The shims bear on the shoulder, the device's rear face on the shims."},"front":{"origin":["{.length}",0,0],"note":"The tines' front: where the build's overall length ends."},"suppressor_seat":{"origin":["{.suppressor_seat_x}",0,0],"note":"On the bore axis where a SOCOM suppressor's rear face stands when locked on, +x toward the muzzle. No source on file for this device shows it: the ledger entry has no measurement yet, and lists the rear end's features it could be set on."}},"interfaces":{"thread":{"type":"muzzle_thread","role":"device","anchor":"thread","params":{"thread":"1/2-28"},"flips":false,"note":"SureFire's number for it is its thread, SF3P-556-1/2-28; its page: \".223 Caliber (5.56mm) + 1/2-28 Thread Pitch\"; \"High-precision single-point cut barrel threads create optimum thread interface\"; \"Installation requires no permanent modifications to most weapons\". No source gives how long a barrel thread it takes: no thread_length. The manual (71-01-997 Rev E): shims between the shoulder and the adapter time the indexing tab to the bottom; \"Torque the adapter between 20 - 30 lb-ft\"; \"Use spacer 71348-1 (sold separately) for shouldered barrels under .620\" diameter\"."},"suppressor_mount":{"type":"suppressor_mount","role":"device","anchor":"suppressor_seat","params":{"system":"surefire-socom"},"flips":false,"note":"SureFire, on its page: \"Mounts all SureFire SOCOM Series sound suppressors\"; \"Serves as rock-solid mounting adapter for SureFire SOCOM Series sound suppressors\"; \"Multiple bearing surfaces provide superior suppressor alignment and prevent ringing of tines inside suppressor\"; \"Labyrinth seals mitigate gas leak from suppressor lock ring\"; \"Note: SureFire SOCOM Series Fast-Attach sound suppressors, flash hider/suppressor adapters, and muzzle brake/suppressor adapters are not compatible with previous SureFire Fast-Attach sound suppressors, muzzle brakes or flash hiders\". The maker's name for the system: SOCOM Series Fast-Attach."}},"materials":{"body":{"label":"Flash hider","finish":"nitride","recolorable":false,"color":"surefire-dlc-black","note":"One colour, black. SureFire: \"CONSTRUCTION Heat-Treated Stainless Steel\", \"COATING DLC Coating\", \"precision machined from U.S. mill-certified heat-treated stainless steel bar stock and DLC-coated\" (https://www.surefire.com/socom-3-prong-flash-hider/). Primary Arms: \"finished with a Black Ionbond DLC coating\". The catalog has no finish type for a diamond-like carbon coat; it is drawn as the nearest it has, a smooth black on steel (`nitride`): Primary Arms' photos show a deep satin black with a soft highlight along each round (30af9029c34b, b963338c145d), Silencer Shop's a flatter charcoal under softer light (1b80beb538dd). The marks lasered on the collar (the maker's logo, the number, the NSN) aren't drawn."},"shims":{"label":"Shims","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"The shim kit's steel shims between the barrel's shoulder and the device (the manual's chart names them by colour for thickness: \"NO COLOR\", \"RED\", \"GREEN\"). No photo of them on file: drawn as bare steel, one thin ring that hardly shows."}},"components":{"body":{"label":"Flash hider","material":"body"},"shims":{"label":"Shims","material":"shims"}},"geometry":{"model":"surefire-socom-3-prong.glb","components":{},"approximations":["Its shape is SureFire's design patent for it (US D687,119 S, which SureFire's patent-marking page lists against SF3P-556), every size scaled by the one figure SureFire publishes, the 2.6 in length: a diameter is good to about 2%. Primary Arms' two straight side photos of SF3P-556-1/2-28 have every station where the patent has it.","Turned from the patent's top plan: the rear boss, the flange and its front cone, the collar, the two seal grooves, the body, its taper, the step ahead of it and the tines' rounded front. Then cut: two wrench flats, the three slots (square-ended with rounded corners, their walls parallel, each through to the axis), the two pockets either side of the indexing tab, the hole through, and the thread.","The indexing tab is drawn as a plain block as high as the flange, from the flange's front to its end (Primary Arms' side photo; the patent draws only its end that high), between two pockets: round-ended cuts with flat floors at the depth the patent's side view shows beside the tab (they may be deeper).","Each tine's front end is square across with a rounded outer corner. The patent's front view and Silencer Shop's photo show a slanted facet on one inner corner of each tine near its tip: not drawn.","The thread is the Army barrel's 1/2-28 cut as a helix, as deep as the Army compensator's bore: how deep this device's thread goes isn't sourced. Behind the tines the hole is the patent's 0.244 in with a chamfered mouth.","The shims that time it are drawn as one ring as wide as the rear boss, at the middle of what the stack can be (none to one pitch of the thread, 0.036 in): the device stands 0.018 in ahead of the shoulder. The shims' own diameter isn't sourced.","Timed as the manual has it: the indexing tab at the bottom, which puts one slot straight up and one tine straight down.","Edges broken at 0.006 in. The lasered marks aren't drawn."],"ledger":["surefire-socom-3-prong.overall_length","surefire-socom-3-prong.shim_stack","surefire-socom-3-prong.length","surefire-socom-3-prong.od","surefire-socom-3-prong.boss_od","surefire-socom-3-prong.collar_od","surefire-socom-3-prong.flats_across","surefire-socom-3-prong.body_od","surefire-socom-3-prong.slot_width","surefire-socom-3-prong.suppressor_seat_x"]},"profiles":{"plan":{"plane":"xz","origin":"the device's rear face, on the bore axis (the shims put it shim_stack ahead of the barrel's shoulder)","offset":{},"points":[[0,0.341],[0,0],[0,-0.341],[0.124,-0.342],[0.168,-0.385],[0.17,-0.479],[0.275,-0.479],[0.348,-0.436],[0.436,-0.438],[0.437,-0.408],[0.481,-0.365],[0.674,-0.365],[0.717,-0.408],[0.718,-0.439],[0.762,-0.439],[0.787,-0.415],[0.813,-0.439],[0.848,-0.439],[0.872,-0.417],[0.895,-0.439],[0.945,-0.439],[0.959,-0.429],[1.659,-0.427],[1.992,-0.42],[2.016,-0.412],[2.49,-0.404],[2.522,-0.398],[2.544,-0.388],[2.574,-0.361],[2.598,-0.311],[2.6,0.295],[2.585,0.346],[2.568,0.367],[2.526,0.395],[2.491,0.404],[2.305,0.407],[2.301,0.403],[2.293,0.407],[2.289,0.403],[2.284,0.407],[2.013,0.41],[1.992,0.42],[1.96,0.415],[1.952,0.42],[1.947,0.415],[1.94,0.42],[1.935,0.415],[1.928,0.42],[1.923,0.415],[1.915,0.42],[1.911,0.415],[1.903,0.42],[1.899,0.415],[1.891,0.42],[1.886,0.415],[1.879,0.42],[1.874,0.415],[1.87,0.42],[1.515,0.43],[0.96,0.429],[0.945,0.438],[0.895,0.438],[0.87,0.415],[0.848,0.438],[0.813,0.438],[0.788,0.414],[0.764,0.438],[0.718,0.438],[0.717,0.405],[0.674,0.362],[0.479,0.362],[0.436,0.405],[0.436,0.436],[0.345,0.436],[0.275,0.479],[0.17,0.479],[0.168,0.385],[0.124,0.342]],"scaleRefs":["surefire-socom-3-prong.overall_length"],"inputs":{"surefire-socom-3-prong.overall_length":2.6},"tolerance":0.004,"photo":"references/surefire-socom-3-prong 6ea6651fb575 (US D687,119 S (SureFire, 'Firearm attachment'), FIG. 5 top plan, the patent office's copy)","method":"luminance < 128, inside [380, 1505, 2125, 2175], closing ×26, holes filled, inset 2 px (half the outline's stroke); scale from surefire-socom-3-prong.overall_length = 2.6 in (x-extent 1707 px → 656.5 px/in); origin at x min, y center of the outline; Douglas-Peucker at 0.004 in with the extremes kept: 78 points (IoU 0.998 with the full outline); checks: height 0.958 ± 0.019 in vs surefire-socom-3-prong.od 0.962 ± 0.02 (corroborated): agrees; height in x [1.1, 1.5] 0.861 ± 0.017 in vs surefire-socom-3-prong.body_od 0.862 ± 0.02 (provisional): agrees; height in x [0.5, 0.66] 0.728 ± 0.015 in vs surefire-socom-3-prong.flats_across 0.731 ± 0.015 (provisional): agrees (tools/trace.py)","via":"harvest","note":"Symmetric about the axis. The flats are the steps in the outline behind the two grooves; the top slot faces the view and isn't in the outline."},"side":{"plane":"xy","origin":"the device's rear face; the middle of the outline's height there, which is the bore axis at the rear boss","offset":{},"points":[[0,0.338],[0,0],[0,-0.34],[0.139,-0.342],[0.166,-0.369],[0.167,-0.48],[0.373,-0.48],[0.397,-0.466],[0.427,-0.438],[0.763,-0.439],[0.787,-0.415],[0.811,-0.439],[0.847,-0.439],[0.871,-0.416],[0.897,-0.439],[0.944,-0.439],[0.96,-0.43],[1.54,-0.43],[1.733,-0.422],[1.99,-0.42],[2.007,-0.412],[2.047,-0.411],[2.483,-0.405],[2.526,-0.396],[2.552,-0.381],[2.577,-0.356],[2.597,-0.311],[2.599,-0.148],[1.071,-0.148],[1.047,-0.144],[1.019,-0.115],[1.05,-0.083],[1.086,-0.072],[2.487,-0.064],[2.549,-0.056],[2.584,-0.043],[2.599,-0.028],[2.6,0.264],[2.592,0.302],[2.557,0.35],[2.524,0.37],[2.483,0.378],[2.015,0.385],[1.99,0.393],[1.496,0.404],[1.081,0.403],[1.036,0.409],[1.013,0.43],[0.966,0.428],[0.94,0.439],[0.894,0.439],[0.868,0.415],[0.843,0.439],[0.817,0.439],[0.787,0.415],[0.763,0.439],[0.346,0.436],[0.273,0.48],[0.166,0.48],[0.166,0.375],[0.136,0.342],[0.007,0.343]],"scaleRefs":["surefire-socom-3-prong.overall_length"],"inputs":{"surefire-socom-3-prong.overall_length":2.6},"tolerance":0.004,"photo":"references/surefire-socom-3-prong a4a308d0b8fc (US D687,119 S (SureFire, 'Firearm attachment'), FIG. 4 right side elevation, the patent office's copy)","method":"luminance < 128, inside [690, 745, 1500, 2735], closing ×18, holes filled, inset 2 px (half the outline's stroke); rotated -90.0° as declared; scale from surefire-socom-3-prong.overall_length = 2.6 in (x-extent 1921 px → 738.8 px/in); origin at x min, y center of the outline; Douglas-Peucker at 0.004 in with the extremes kept: 62 points (IoU 0.996 with the full outline); checks: height 0.960 ± 0.019 in vs surefire-socom-3-prong.od 0.962 ± 0.02 (corroborated): agrees; height in x [0.5, 0.66] 0.878 ± 0.017 in vs surefire-socom-3-prong.collar_od 0.88 ± 0.02 (provisional): agrees; y_min in x [0.38, 0.4] -0.474 ± 0.009; y_max in x [0.38, 0.4] 0.436 ± 0.009 (tools/trace.py)","via":"harvest","note":"The muzzle to the right, the tab down. Above the axis the outline ahead of the seal is the top slot's edge, lower than the body's radius; below it, the bottom tine's."}},"gaps":[{"what":"Where a SOCOM suppressor's rear face stands on it (suppressor_seat_x)","need":"a photo of the device with a suppressor locked on, square from the side, or the suppressor's manual's drawing of the two together; the suppressor's own sources may have it"},{"what":"Any diameter as the maker states it: every one is the patent's drawing scaled by the 2.6 in length, which two sellers give as 2.67","need":"SureFire's drawing or product sheet (its host refuses the reader), or a seller's table with a diameter"},{"what":"The thread's depth, and the inside between the thread and the tines","need":"a section drawing, or a photo straight into the rear end"},{"what":"The slanted facet on each tine's inner corner at its tip","need":"a photo square on the muzzle end: the patent's front view shows where it is and not how deep"}]},"surefire-socom-4-prong":{"id":"surefire-socom-4-prong","name":"SOCOM 4-Prong Flash Hider","manufacturer":"SureFire","sku":"FH556RC-1/2-28","url":"https://www.surefire.com/socom-4-prong-flash-hider/","category":"muzzle_device","description":"The four-tine flash hider SureFire's SOCOM suppressors were first made to lock onto: four tines between slots cut to one side of the bore, a two-groove labyrinth seal, wrench flats, and a flange with the indexing tab.","weight":"surefire-socom-4-prong.weight","cartridge":{"takes":["5.56 NATO",".223 Rem"],"stated":".223 Caliber (5.56mm) + 1/2-28 Thread Pitch","source":"https://www.surefire.com/socom-4-prong-flash-hider/ (the page's Model choice for FH556RC-1/2-28, as cached: harvest.quote; \"Our FH556RC-1/2-28 SOCOM 4-Prong Flash Hider for 5.56 mm weapon platforms\")"},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"thread":{"origin":[0,0,0],"note":"Device frame: on the bore axis at the barrel's shoulder, +x toward the muzzle. The shims bear on the shoulder, the device's rear face on the shims."},"front":{"origin":["{.length}",0,0],"note":"The tines' front: where the build's overall length ends."},"suppressor_seat":{"origin":["{.suppressor_seat_x}",0,0],"note":"On the bore axis where a SOCOM suppressor's rear face stands when locked on, +x toward the muzzle. No source on file for this device shows it: the ledger entry has no measurement yet, and lists the rear end's features it could be set on."}},"interfaces":{"thread":{"type":"muzzle_thread","role":"device","anchor":"thread","params":{"thread":"1/2-28"},"flips":false,"note":"SureFire's number for it is its thread, FH556RC-1/2-28; its page: \".223 Caliber (5.56mm) + 1/2-28 Thread Pitch\". No source gives how long a barrel thread it takes: no thread_length. Its own manual (71-01-828) is on a host that refuses the reader; SureFire's adapter manual on file (71-01-997 Rev E) times its adapters with shims between the shoulder and the adapter."},"suppressor_mount":{"type":"suppressor_mount","role":"device","anchor":"suppressor_seat","params":{"system":"surefire-socom"},"flips":false,"note":"SureFire, on its page: \"The exact flash hider that helped create the SureFire SOCOM legacy\"; \"Multiple bearing surfaces provide superior suppressor alignment\"; \"Our FH556RC-1/2-28 SOCOM 4-Prong Flash Hider for 5.56 mm weapon platforms is the exact flash hider that SureFire developed to dominate the most rigorous suppressor trial in military history and earn the USSOCOM suppressor contract\". The maker's name for the system: SOCOM Fast-Attach (\"SureFire SOCOM Fast-Attach suppressor\", the same page)."}},"materials":{"body":{"label":"Flash hider","finish":"nitride","recolorable":false,"color":"surefire-dlc-black","note":"One colour. SureFire: \"CONSTRUCTION Heat Treated Stainless Steel\", \"COATING DLC Coating\" (https://www.surefire.com/socom-4-prong-flash-hider/). The catalog has no finish type for a diamond-like carbon coat; it is drawn as the nearest it has, a smooth black on steel (`nitride`). Primary Arms' three photos of it are lit to a mid grey (c9ac820f803b), SureFire's own picture a dark grey (504964c1525f): the studio's light, as on its siblings. The lasered marks aren't drawn."},"shims":{"label":"Shims","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"The shim kit's steel shims between the barrel's shoulder and the device. No photo of them on file: drawn as bare steel, one thin ring that hardly shows."}},"components":{"body":{"label":"Flash hider","material":"body"},"shims":{"label":"Shims","material":"shims"}},"geometry":{"model":"surefire-socom-4-prong.glb","components":{},"approximations":["Only one straight view of it is on file (Primary Arms', along one of its slots): every section's diameter and station is read there and scaled by the 2.6 in SureFire publishes. Its diameters are as the photo reads them, which on a dark part against white may be up to 3% thin.","Turned: the rear boss, the flange and its front cone, the collar, the two seal grooves, the body, its taper, the step ahead of it and the tines' rounded front. Then cut: two wrench flats, the four slots, the pockets either side of the indexing tab, the hole through, and the thread.","The four slots are a quarter turn apart, round-ended, their walls parallel, each cut to one side of the bore (0.074 in off it, all the same way round), as the straight view shows them: looking through two opposite slots only a slit of daylight shows.","How it is turned about its axis is read by eye on the rear three-quarter photo: the indexing tab in line with a tine, so a tine is straight down and the slots lie on the diagonals; the flats are drawn left and right, a quarter turn from the tab, where the one seen in the straight view would be.","The indexing tab and its two pockets aren't measured on this part (they don't show in the straight view): drawn as the 3-prong's, which the same suppressors index on. The flats' width is rough, from one flat seen 45° off.","The thread is the Army barrel's 1/2-28 cut as a helix, as deep as the Army compensator's bore, and the hole ahead of it the 3-prong's: neither is sourced for this device.","The shims that time it are drawn as one ring as wide as the rear boss, at the middle of what the stack can be (none to one pitch of the thread, 0.036 in).","Edges broken at 0.006 in. The lasered marks aren't drawn."],"ledger":["surefire-socom-4-prong.overall_length","surefire-socom-4-prong.shim_stack","surefire-socom-4-prong.length","surefire-socom-4-prong.od","surefire-socom-4-prong.boss_od","surefire-socom-4-prong.collar_od","surefire-socom-4-prong.flats_across","surefire-socom-4-prong.body_od","surefire-socom-4-prong.slot_width","surefire-socom-4-prong.slot_offset","surefire-socom-4-prong.suppressor_seat_x"]},"profiles":{"side":{"plane":"xy","origin":"the device's rear face; the middle of the outline's height there, which is the bore axis at the rear boss","offset":{},"points":[[0,-0.001],[0,-0.089],[0.016,-0.323],[0.042,-0.336],[0.158,-0.336],[0.167,-0.345],[0.175,-0.423],[0.187,-0.459],[0.205,-0.473],[0.292,-0.473],[0.368,-0.43],[0.783,-0.434],[0.796,-0.41],[0.824,-0.41],[0.838,-0.434],[0.865,-0.434],[0.877,-0.412],[0.906,-0.41],[0.918,-0.434],[0.953,-0.436],[0.995,-0.426],[1.967,-0.42],[2.059,-0.412],[2.452,-0.401],[2.513,-0.391],[2.552,-0.371],[2.569,-0.354],[2.594,-0.303],[2.6,-0.046],[2.589,-0.035],[2.473,-0.026],[1.15,-0.024],[1.091,-0.031],[1.063,-0.024],[1.051,-0.013],[1.069,0.008],[1.099,0.018],[2.409,0.006],[2.591,0.014],[2.6,0.237],[2.594,0.29],[2.574,0.333],[2.534,0.367],[2.469,0.383],[2.053,0.395],[2.014,0.397],[1.992,0.405],[1.004,0.418],[0.949,0.428],[0.922,0.428],[0.908,0.403],[0.887,0.403],[0.874,0.411],[0.867,0.428],[0.855,0.43],[0.839,0.425],[0.828,0.403],[0.8,0.403],[0.786,0.428],[0.37,0.428],[0.299,0.471],[0.217,0.473],[0.199,0.469],[0.187,0.453],[0.171,0.351],[0.162,0.336],[0.046,0.338],[0.03,0.332],[0.014,0.313]],"scaleRefs":["surefire-socom-4-prong.overall_length"],"inputs":{"surefire-socom-4-prong.overall_length":2.6},"tolerance":0.004,"photo":"references/surefire-socom-4-prong c9ac820f803b (Primary Arms FH556RC-1-2-28_02: the device standing, seen square along one of its slots, on white)","method":"luminance < 200, inside [700, 50, 1500, 1460], closing ×2, largest piece, holes filled; rotated -90.0° as declared; scale from surefire-socom-4-prong.overall_length = 2.6 in (x-extent 1276 px → 490.8 px/in); origin at x min, y center of the outline; Douglas-Peucker at 0.004 in with the extremes kept: 69 points (IoU 0.993 with the full outline); checks: height 0.945 ± 0.019 in vs surefire-socom-4-prong.od 0.945 ± 0.03 (provisional): agrees; height in x [0.5, 0.7] 0.864 ± 0.018 in vs surefire-socom-4-prong.collar_od 0.862 ± 0.03 (provisional): agrees (tools/trace.py)","via":"harvest","note":"NOT a view from the rifle's side: the lens looks along a slot, 45° round from where the model has its tines, and which way up it stood isn't known. The notch from the front is daylight through two slots in line. Kept as the record of what was measured; the model is turned from the ledger's sections."}},"gaps":[{"what":"Where a SOCOM suppressor's rear face stands on it (suppressor_seat_x)","need":"a photo of the device with a suppressor locked on, square from the side, or its manual's drawing (71-01-828, on a host that refuses the reader)"},{"what":"The indexing tab and its pockets, the flats' width, and how the slots and flats are turned to the tab","need":"straight photos from below and from the muzzle end: one straight view is on file, and the tab isn't in it"},{"what":"Any diameter as the maker states it; its length, which SureFire gives as 2.6 in and as 6.4 cm (2.52 in) and a seller as 2.67","need":"SureFire's product sheet or drawing"},{"what":"The inside: the thread's depth and the hole through","need":"a section drawing, or photos straight into both ends"}]},"surefire-socom556-rc2":{"id":"surefire-socom556-rc2","name":"SOCOM556-RC2","manufacturer":"SureFire","sku":"SOCOM556-RC2-BK","url":"https://www.surefire.com/socom556-rc2/","category":"suppressor","description":"A 5.56 mm suppressor that locks onto a SureFire SOCOM muzzle device with a half turn of its lock ring and comes off without tools: a plain tube with a recessed front plate, and at the rear a fluted lock ring with a spring latch. SureFire rates it for barrels of 10 inches and longer. Modelled from the outside only.","weight":"surefire-socom556-rc2.weight","nfa":"silencer","cartridge":{"takes":["5.56 NATO",".223 Rem"],"stated":"CALIBER 5.56 mm (.223 caliber); \"Optimized for any 5.56 mm/.223-caliber weapon system with a minimum barrel length of 10 inches\"; \"Designed specifically for 10-inch and longer M4/M16-variant rifles and carbines\"; \"Durable high-temperature Inconel alloy/stainless-steel construction withstands full-auto use\"","source":"https://www.surefire.com/socom556-rc2/ (Key Attributes, the description and the features, as cached: harvest.quote, 2026-10-06). Primary Arms says of the same number \"Designed for 10.5” and longer M4/M16 variant carbines\" (https://www.primaryarms.com/surefire-socom-2-qd-sound-suppressor-socom556-rc2-bk). SureFire's sound figures on the page are for 10.3, 14.5 and 16.0 in barrels with M855."},"mass":{"note":"Only the whole suppressor's weight is published, and nothing inside it is modelled: the drawn solid is hollow at the rear (the socket) and solid at the front, which would put its weight 0.45 in ahead of its middle. The weight is spread evenly along its length instead, as a tube of the published diameter from end to end. Where a real one balances isn't sourced.","lumps":{"whole":{"tube":{"from":[0,0,0],"to":["{.length}",0,0],"od":"{.od}"},"rest":true}}},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"mount":{"origin":[0,0,0],"note":"Suppressor frame: on its axis at its rear face (the lock ring's), +x toward the muzzle. Where it stands on a muzzle device is that device's half of the seat (its `suppressor_seat` anchor): by SureFire's manual's Figures 6 and 7A and by its own figures (6.4 long, adds 3.8 on a 2.6 in adapter), the device's rear face, on the barrel's shoulder (the ledger's seat_ahead_of_device_rear)."},"front":{"origin":["{.length}",0,0],"note":"The front rim: where the build's overall length ends."}},"interfaces":{"mount":{"type":"suppressor_mount","role":"suppressor","anchor":"mount","params":{"system":"surefire-socom"},"flips":false,"note":"SureFire: \"Compatible with the SureFire array of Fast-Attach® mounting adapters (flash hiders, Muzzle brakes, and WARCOMPS)\" and \"Fast-Attach® design allows fast, secure, easy attachment and removal without tools\" (https://www.surefire.com/socom556-rc2/). Its manual (71-01-863 Rev G, as Silencer Central hosts it): \"Slide the suppressor over the adapter ... Rotate counterclockwise until the indexing slot on the suppressor (Figure 5B) lines up with and seats onto the indexing tab on the adapter (Figure 5A). Ensure that the suppressor is fully seated onto the adapter.\" and \"Rotate the lock ring to locked position ... until it can no longer be rotated. The lock ring should rotate approximately 180º.\" Capitol Armory: \"NOTE: This suppressor requires a SureFire muzzle device for mounting.\""}},"materials":{"body":{"label":"Body","finish":"cerakote","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"cerakote","color":"placeholder-black","sku":"SOCOM556-RC2-BK","source":"https://www.surefire.com/socom556-rc2/"},"dark-earth":{"label":"Dark Earth","finish":"cerakote","color":"surefire-dark-earth-cerakote","sku":"SOCOM556-RC2-DE","source":"https://www.surefire.com/socom556-rc2/"}},"default":"black","note":"The tube and its front plate, one colour in each colourway. SureFire: \"COATING DLC and Cerakote™ Finish\", \"BODY COLORS Black, Dark Earth\", part numbers SOCOM556-RC2-BK and SOCOM556-RC2-DE (https://www.surefire.com/socom556-rc2/); sellers: \"Finish: High-temp Cerakote\" (Capitol Armory), \"Finish Cerakote\" and \"Color Flat Dark Earth\" (Primary Arms). Metal under it: \"High-Temp Alloy & Stainless Steel\". Black is a flat black in Primary Arms' photos (5cbae164067f, c6f8eeb9ce13), not fitted (a black); Dark Earth is fitted to its photos of that one (2ef29d436724, c5a2d597da99). Piece by piece, from Primary Arms' photos of each (2026-10-06): the front plate and the collar round the bore are the body's colour in both; the bore's wall is bare and dark."},"ring":{"label":"Lock ring","finish":"nitride","recolorable":false,"color":"surefire-dlc-black","follows":{"slot":"body","options":{"dark-earth":{"finish":"cerakote","color":"surefire-dark-earth-cerakote"}}},"note":"On the black one a dark warm grey, smoother than the tube and lighter than it under a studio's light (5cbae164067f, a2f86f6ddb7e, 89bfa38440ab): the DLC of \"DLC and Cerakote™ Finish\", which SureFire's manual calls \"the ionbond coating on the lock ring\" (71-01-863 Rev G, 10.3); a black on hard steel, not fitted (drawn under `nitride`, the nearest finish the catalog has, as SureFire's muzzle devices are). On the Dark Earth one the ring is tan as the tube is (2ef29d436724, 0b6cdb056ffe, 2b4e7d4cd0be), a little more golden and worn at its edges on the unit photographed: drawn in the body's Dark Earth."},"latch":{"label":"Lock ring latch","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The tab marked PUSH and its arm: black on both colourways (a2f86f6ddb7e; 0b6cdb056ffe and 2ef29d436724 on the Dark Earth one, where its screw at the ring's rear edge is black too). What it is coated with isn't said."},"collar":{"label":"Toothed collar","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"Bright bare steel on both colourways: the ring of fine teeth the latch bears on, in the gap between the lock ring and the body and under the latch (0b6cdb056ffe, 2ef29d436724, 89bfa38440ab). SureFire names the metal only as \"High-Temp Alloy & Stainless Steel\"."}},"components":{"body":{"label":"Body","material":"body"},"ring":{"label":"Lock ring","material":"ring"},"latch":{"label":"Lock ring latch","material":"latch"},"collar":{"label":"Toothed collar","material":"collar"}},"geometry":{"model":"surefire-socom556-rc2.glb","components":{},"approximations":["The body is a plain tube of the published 1.5 in from 0.83 in ahead of the rear face to the front, its rear shoulder and front corner rounded (0.09 and 0.075 in) as the side photo has them. Primary Arms' side view, scaled by the tube itself, is the tube's size within 0.006 in from shoulder to front, and reads 6.39 in between its end faces: SureFire's 6.4, not the 6.2 some sellers print.","The front plate is recessed 0.16 in behind the rim, with a collar 0.48 in across standing 0.06 in from its floor round a 0.35 in bore. The rim's inner edge has eight flats (1.22 in across them); under each a flat wall, turning round on the way down to a round floor 0.90 in across. How the flat walls really turn into the floor isn't read (no view is square to the face), nor which way round the flats stand: one is drawn on top. The small nicks the side photos show where the rim's corners meet its outer round aren't drawn: as measured, the corners stop 0.015 in short of it.","The lock ring is drawn locked, on the body's axis and at the tube's diameter, as SureFire's manual's Figures 6 and 7A draw it. Unlocked, as every product photo has it, it sits up to 0.05 in off the axis (Figure 7B).","Six flutes round the ring, 45 degrees apart with the two places beside the latch left out, each 0.41 in wide and running from the rear rim to a round end 0.61 in from the rear face. Their floors are drawn 0.03 in deep and following the ring's round: the depth is an estimate from a shadow, and no view looks along a flute.","The latch is its tab (marked PUSH; 0.33 by 0.30 in, its top 0.037 in outside the tube's line) and a plain arm 0.15 in wide round the ring's front edge, in a pocket 0.06 in deep that runs 47 degrees round from the tab one way and 25 the other. Its real arm hooks round a pivot pin and has a spring under it; the pin, the spring and the black screw at the ring's rear edge aren't drawn. The pocket's depth is weak (one photo).","Which way round the suppressor stands on a rifle is set by the adapter's indexing tab, which SureFire has timed to the bottom (\"bottom dead center\", its adapter installation manual). It is drawn as SureFire's Figures 6 and 7A have it locked on such an adapter: the latch low on the rifle's right. On a WARCOMP clocked to one side it would stand turned with it.","The toothed steel collar the latch bears on is a plain cylinder 1.26 in across showing in the gap between the ring and the body: its teeth (about a hundredth of an inch) aren't drawn.","Nothing inside is modelled. The opening in the lock ring (1.03 in) is carried forward as a plain socket to the middle, where it meets the exit bore cut back from the front: a SureFire adapter (2.6 to 2.7 in long, 0.96 in across its flange) stands wholly inside it. The indexing slot in the socket, the socket's real steps and tapers, and the baffles aren't drawn.","Not drawn: the engraving (SUREFIRE LLC, FOUNTAIN VALLEY, CA., SOCOM556-RC2 CAL:5.56MM, the serial), which is on the side that faces the lens in SureFire's figures."],"ledger":["surefire-socom556-rc2.length","surefire-socom556-rc2.od","surefire-socom556-rc2.half_length","surefire-socom556-rc2.body_rear_x","surefire-socom556-rc2.body_shoulder_round","surefire-socom556-rc2.front_corner_round","surefire-socom556-rc2.crown_flats","surefire-socom556-rc2.crown_across_flats","surefire-socom556-rc2.dish_d","surefire-socom556-rc2.front_recess","surefire-socom556-rc2.boss_d","surefire-socom556-rc2.boss_height","surefire-socom556-rc2.bore_d","surefire-socom556-rc2.rear_bore_d","surefire-socom556-rc2.collar_d","surefire-socom556-rc2.ring_length","surefire-socom556-rc2.ring_d","surefire-socom556-rc2.ring_rear_round","surefire-socom556-rc2.ring_front_chamfer","surefire-socom556-rc2.flutes","surefire-socom556-rc2.flute_pitch","surefire-socom556-rc2.flute_width","surefire-socom556-rc2.flute_length","surefire-socom556-rc2.flute_depth","surefire-socom556-rc2.latch_angle","surefire-socom556-rc2.latch_x0","surefire-socom556-rc2.latch_x1","surefire-socom556-rc2.latch_width","surefire-socom556-rc2.latch_proud","surefire-socom556-rc2.latch_pocket_x","surefire-socom556-rc2.latch_pocket_depth","surefire-socom556-rc2.latch_pocket_behind","surefire-socom556-rc2.latch_pocket_ahead","surefire-socom556-rc2.latch_arm_width"]},"profiles":{"side":{"plane":"xy","origin":"the middle of the silhouette, on the tube's axis: the rear face is half the overall length behind it","offset":{"x":"half_length"},"points":[[-3.2,0.648],[-3.2,-0.649],[-3.153,-0.7],[-3.107,-0.722],[-2.464,-0.722],[-2.439,-0.714],[-2.402,-0.682],[-2.375,-0.629],[-2.373,-0.653],[-2.351,-0.704],[-2.302,-0.74],[-2.281,-0.749],[1.823,-0.752],[1.828,-0.748],[2.134,-0.75],[2.139,-0.746],[2.143,-0.75],[2.198,-0.746],[2.203,-0.75],[2.42,-0.752],[2.433,-0.748],[2.437,-0.752],[2.441,-0.748],[2.757,-0.75],[2.761,-0.746],[2.948,-0.751],[2.953,-0.747],[3.136,-0.744],[3.179,-0.727],[3.198,-0.704],[3.2,0.694],[3.179,0.728],[3.136,0.745],[2.953,0.746],[2.948,0.751],[2.45,0.75],[2.446,0.746],[2.437,0.75],[2.433,0.746],[2.42,0.75],[2.203,0.752],[2.198,0.747],[2.143,0.752],[2.139,0.748],[0.891,0.752],[0.886,0.748],[0.58,0.75],[0.575,0.745],[0.269,0.752],[0.264,0.747],[-0.353,0.752],[-0.357,0.747],[-0.979,0.752],[-0.983,0.747],[-1.6,0.752],[-1.604,0.747],[-2.281,0.748],[-2.302,0.739],[-2.351,0.703],[-2.373,0.653],[-2.375,0.629],[-2.402,0.682],[-2.439,0.715],[-2.464,0.723],[-3.107,0.723],[-3.153,0.702]],"scaleRefs":["surefire-socom556-rc2.od","surefire-socom556-rc2.length"],"inputs":{"surefire-socom556-rc2.length":6.4,"surefire-socom556-rc2.od":1.5},"tolerance":0.004,"photo":"references/surefire-socom556-rc2 2ef29d436724 (Primary Arms SOCOM556-RC2-DE_01: the Dark Earth suppressor from its right side on white, 2000 x 1334)","method":"luminance < 235, largest piece, holes filled; the turned body alone: at each column the smaller of the dark run's reach above and below the tube's axis, taken both ways; scale from surefire-socom556-rc2.od = 1.5 in, the tube's own width column by column: 352.8 px over columns 520–900, 352.6 px over columns 1000–1650; a line through them (rms 0.14 px) changes -0.1% from column 520 to 1650, so the photo is yawed and one scale would not do. Heights by each column's width; lengths by (u − 1000)/width, the lens's axis taken to meet the image at column 1000; 235.1 px/in there. The axis is the tube's centre line (tilt -0.39°, rms 0.08 px). Lengths then scaled by 1.0012 so that the end faces are surefire-socom556-rc2.length = 6.4 in apart: at the tube's scale they read 6.392 (-0.1%; the yaw's cosine and where the lens's axis meets the image are in that). Each face is taken behind its rim's arc: the front end's rim sags 0.086 in over radius 0.748 (rms 0.016), the rear end's rim sags 0.093 in over radius 0.724 (rms 0.013); origin at x center of the outline, on the tube's axis; clipped to x min -{.length} / 2 = -3.2, x max {.length} / 2 = 3.2; Douglas-Peucker at 0.004 in with the extremes kept: 66 points (IoU 0.998 with the full outline); Scaled by the tube's own 1.5 in, column by column; at that scale the end faces, each taken behind its rim's arc, are 6.39 in apart, which is SureFire's 6.4 and not the 6.2 of three sellers. The silhouette's tips are 6.575 apart (each end's near rim stands nearer the lens than the axis does) and the outline is trimmed to the published length about its middle. What is above the tube's line at the ring (the latch) is left out: at each column the smaller of the reaches above and below the axis.; checks: width 6.575 ± 0.220 (tools/trace.py)","via":"harvest","note":"The lock ring at the rear, the front plate's rim at the front. The outline is the turned envelope: the ring's flutes and latch, the collar's teeth and the front rim's flats aren't in it, and the ring reads 0.03 in inside its drawn size because it is unlocked in the photo (ring_d)."}},"gaps":[{"what":"A view straight at either end","need":"a photo square on the lock ring's end and one square on the front plate: the opening's size, the ring's wall, the front rim's flats and where they stand round the axis are read off three-quarter views here"},{"what":"A flute's depth, the latch pocket's depth, and the latch's real shape","need":"a photo along a flute and one square on the latch with the ring locked, close up; SureFire's manual draws the latch in outline only (Figures 6 and 7A)"},{"what":"The socket: its steps and tapers, the indexing slot, how deep it is","need":"SureFire's drawing of the back section, or a photo straight into the rear end; the model's socket is a plain bore at the opening's size"},{"what":"SureFire's product sheet and the manual's own copy","need":"they are on SureFire's file host, whose robots.txt disallows them: the user could save SOCOM556-RC2_PIS.pdf from their own browser (it has a photo of a Dark Earth RC2 on a Mk18, by the discovery's account, which would show the seat on a rifle). The manual is on file as Silencer Central hosts it"}]},"surefire-warcomp":{"id":"surefire-warcomp","name":"WARCOMP Flash Hider","manufacturer":"SureFire","sku":"WARCOMP-556-1/2-28","url":"https://www.surefire.com/warcomp-flash-hider/","category":"muzzle_device","description":"A three-tine flash hider with two rows of ports round its collar, turned toward one side to hold the muzzle down, that SureFire's SOCOM suppressors lock onto: a flange with the indexing tab that is timed with shims.","weight":"surefire-warcomp.weight","cartridge":{"takes":["5.56 NATO",".223 Rem"],"stated":".223 Caliber (5.56mm) + 1/2-28 Thread Pitch","source":"https://www.surefire.com/warcomp-flash-hider/ (the page's Model choice for WARCOMP-556-1/2-28, as cached: harvest.quote)"},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"thread":{"origin":[0,0,0],"note":"Device frame: on the bore axis at the barrel's shoulder, +x toward the muzzle. The shims bear on the shoulder, the device's rear face on the shims."},"front":{"origin":["{.length}",0,0],"note":"The tines' front: where the build's overall length ends."},"suppressor_seat":{"origin":["{.suppressor_seat_x}",0,0],"note":"On the bore axis where a SOCOM suppressor's rear face stands when locked on, +x toward the muzzle. No source on file for this device shows it: the ledger entry has no measurement yet, and lists the rear end's features it could be set on."}},"interfaces":{"thread":{"type":"muzzle_thread","role":"device","anchor":"thread","params":{"thread":"1/2-28"},"flips":false,"note":"SureFire's number for it is its thread, WARCOMP-556-1/2-28; its page: \".223 Caliber (5.56mm) + 1/2-28 Thread Pitch\"; \"High-precision single-point cut barrel threads for optimum thread interface\"; \"Installation requires no permanent modifications to weapon\". No source gives how long a barrel thread it takes: no thread_length. The manual (71-01-997 Rev E): shims between the shoulder and the adapter time the indexing tab; \"Torque the adapter between 20 - 30 lb-ft\"; \"The WARCOMP models above can be clocked in different positions as shown to improve muzzle rise for right- or left-handed shooters or set in the neutral position\"; \"Use spacer 71348-1 (sold separately) for shouldered barrels under .620\" diameter\"."},"suppressor_mount":{"type":"suppressor_mount","role":"device","anchor":"suppressor_seat","params":{"system":"surefire-socom"},"flips":false,"note":"SureFire, on its page: \"Serves as a rock-solid mounting adapter for SureFire SOCOM suppressors\"; \"Multiple bearing surfaces provide suppressor alignment and prevent tines from ringing inside suppressor\". The manual: \"Clocking the adapter does not reduce suppressor performance. However, when clocked for right or left-handed shooters, the suppressor won't be indexed at the bottom-dead-center position.\" The maker's name for the system: SOCOM Series Fast-Attach (Mile High: \"When used in conjunction with a SureFire SOCOM Series Fast-...\")."}},"materials":{"body":{"label":"Flash hider","finish":"nitride","recolorable":false,"color":"surefire-dlc-black","note":"One colour, black. SureFire: \"CONSTRUCTION Heat Treated Stainless Steel\", \"COATING DLC Coating\", \"Precision-machined and DLC-coated for high performance and long service life\" (https://www.surefire.com/warcomp-flash-hider/). Mile High: \"the WARCOMP-556-1/2-28 features an Ionbond DLC coating\". The catalog has no finish type for a diamond-like carbon coat; it is drawn as the nearest it has, a smooth black on steel (`nitride`): Primary Arms' photos show a deep satin black (b6910adbb177, 0b49401e457d), T.REX ARMS' a blue-grey under a coloured light (6510c16e0122). The marks lasered on the rear boss aren't drawn."},"shims":{"label":"Shims","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"The shim kit's steel shims between the barrel's shoulder and the device (the manual's chart names them by colour for thickness: \"NO COLOR\", \"RED\", \"GREEN\"). No photo of them on file: drawn as bare steel, one thin ring that hardly shows."}},"components":{"body":{"label":"Flash hider","material":"body"},"shims":{"label":"Shims","material":"shims"}},"geometry":{"model":"surefire-warcomp.glb","components":{},"approximations":["Every size is read on Primary Arms' two straight photos of WARCOMP-556-1/2-28, a quarter turn apart, each scaled by the one figure SureFire publishes, the 2.7 in length. Its diameters are as the photos read them, which on a black part against white may be up to 3% thin.","Turned: the rear boss, the flange and its front cone, the ported collar, the body, the small step in it, the tines' rounded front. Then cut: the three slots (square-ended, their walls parallel, each through to the axis), the two pockets either side of the indexing tab, the twelve ports, the hole through, and the thread. No wrench flats: it has none.","The ports are plain round holes square to the axis, two rows of six, in two groups of three columns either side of a plane 47° to the right of the top, as counted and placed on the photos with the tab at the bottom: the timing the manual's drawing calls RIGHT HANDED. Whether they are drilled at a slant, and what they open into, isn't sourced.","The indexing tab is a plain block as high as the flange, from the flange's front to its end, between two pockets drawn as round-ended cuts with flat floors at the depth of the 3-prong's (theirs isn't read on this part).","Each tine's front end is square across with a rounded outer corner.","The thread is the Army barrel's 1/2-28 cut as a helix, as deep as the Army compensator's bore, and the hole ahead of it the 3-prong's: neither is sourced for this device, and the rear row of ports lies over the end of the thread as drawn.","The shims that time it are drawn as one ring as wide as the rear boss, at the middle of what the stack can be (none to one pitch of the thread, 0.036 in). The shims' own diameter isn't sourced.","Edges broken at 0.006 in. The lasered marks aren't drawn."],"ledger":["surefire-warcomp.overall_length","surefire-warcomp.shim_stack","surefire-warcomp.length","surefire-warcomp.od","surefire-warcomp.boss_od","surefire-warcomp.collar_od","surefire-warcomp.body_od","surefire-warcomp.slot_width","surefire-warcomp.port_d","surefire-warcomp.suppressor_seat_x"]},"profiles":{"plan":{"plane":"xz","origin":"the device's rear face, on the bore axis (the shims put it shim_stack ahead of the barrel's shoulder)","offset":{},"points":[[0,0],[0,-0.135],[0.007,-0.236],[0.019,-0.296],[0.03,-0.322],[0.062,-0.339],[0.212,-0.339],[0.221,-0.348],[0.225,-0.393],[0.24,-0.453],[0.257,-0.474],[0.271,-0.477],[0.346,-0.474],[0.391,-0.444],[0.425,-0.433],[1.013,-0.433],[1.043,-0.414],[2.088,-0.418],[2.099,-0.41],[2.612,-0.41],[2.657,-0.388],[2.681,-0.363],[2.696,-0.333],[2.7,0.296],[2.696,0.333],[2.681,0.363],[2.649,0.395],[2.619,0.41],[2.582,0.418],[2.099,0.414],[2.058,0.425],[1.144,0.421],[1.122,0.41],[1.069,0.41],[1.024,0.414],[1.015,0.423],[1.017,0.429],[0.998,0.433],[0.433,0.433],[0.41,0.444],[0.391,0.444],[0.369,0.466],[0.365,0.462],[0.358,0.47],[0.343,0.47],[0.335,0.477],[0.271,0.477],[0.264,0.47],[0.249,0.474],[0.236,0.449],[0.221,0.352],[0.208,0.339],[0.047,0.339],[0.036,0.335],[0.026,0.322],[0.015,0.285],[0.004,0.195]],"scaleRefs":["surefire-warcomp.overall_length"],"inputs":{"surefire-warcomp.overall_length":2.7},"tolerance":0.004,"photo":"references/surefire-warcomp b6910adbb177 (Primary Arms WARCOMP-556-1-2-28_02: the device standing, seen square from its underside, on white)","method":"luminance < 200, inside [700, 250, 1300, 1150], closing ×2, largest piece, holes filled; rotated -90.0° as declared; scale from surefire-warcomp.overall_length = 2.7 in (x-extent 721 px → 267.0 px/in); origin at x min, y center of the outline; Douglas-Peucker at 0.004 in with the extremes kept: 57 points (IoU 0.996 with the full outline); checks: height 0.955 ± 0.021 in vs surefire-warcomp.od 0.947 ± 0.03 (corroborated): agrees; height in x [0.6, 0.9] 0.873 ± 0.020 in vs surefire-warcomp.collar_od 0.869 ± 0.03 (provisional): agrees; height in x [1.3, 1.9] 0.839 ± 0.019 in vs surefire-warcomp.body_od 0.839 ± 0.03 (provisional): agrees (tools/trace.py)","via":"harvest","note":"Seen from below, so the rifle's right is at the top of the outline; it is symmetric but for two ports' edges on that side."},"side":{"plane":"xy","origin":"the device's rear face; the middle of the outline's height there, which is the bore axis at the rear boss","offset":{},"points":[[0,0],[0,-0.111],[0.019,-0.279],[0.033,-0.319],[0.05,-0.336],[0.21,-0.336],[0.223,-0.349],[0.223,-0.371],[0.241,-0.449],[0.258,-0.47],[0.336,-0.477],[0.459,-0.477],[0.481,-0.466],[0.487,-0.449],[0.5,-0.436],[0.555,-0.436],[0.581,-0.429],[1.016,-0.425],[1.027,-0.414],[1.053,-0.407],[2.089,-0.407],[2.1,-0.399],[2.264,-0.403],[2.416,-0.396],[2.616,-0.396],[2.663,-0.364],[2.681,-0.342],[2.693,-0.312],[2.7,-0.279],[2.698,-0.147],[1.179,-0.143],[1.159,-0.13],[1.159,-0.104],[1.194,-0.065],[2.078,-0.061],[2.119,-0.054],[2.628,-0.05],[2.672,-0.032],[2.7,-0.004],[2.7,0.26],[2.693,0.319],[2.67,0.357],[2.62,0.392],[2.572,0.399],[1.183,0.399],[1.123,0.418],[1.042,0.418],[1.016,0.433],[0.993,0.436],[0.477,0.433],[0.451,0.44],[0.436,0.436],[0.422,0.448],[0.407,0.444],[0.336,0.477],[0.266,0.477],[0.247,0.47],[0.241,0.461],[0.227,0.416],[0.219,0.353],[0.21,0.344],[0.098,0.336],[0.072,0.344],[0.046,0.34],[0.026,0.319],[0.004,0.189]],"scaleRefs":["surefire-warcomp.overall_length"],"inputs":{"surefire-warcomp.overall_length":2.7},"tolerance":0.004,"photo":"references/surefire-warcomp 0b49401e457d (Primary Arms WARCOMP-556-1-2-28_03: the device standing, seen square from its right side, on white)","method":"luminance < 200, inside [700, 250, 1300, 1150], closing ×2, largest piece, holes filled; rotated -90.0° as declared; scale from surefire-warcomp.overall_length = 2.7 in (x-extent 727 px → 269.3 px/in); origin at x min, y center of the outline; Douglas-Peucker at 0.004 in with the extremes kept: 66 points (IoU 0.994 with the full outline); checks: height 0.954 ± 0.021 in vs surefire-warcomp.od 0.947 ± 0.03 (corroborated): agrees; y_min in x [0.38, 0.45] -0.477 ± 0.010; y_max in x [0.38, 0.45] 0.459 ± 0.010 (tools/trace.py)","via":"harvest","note":"The muzzle to the right, the tab down. Above the axis the outline ahead of the collar is the top slot's edge; the slot at the lower right shows as a notch from the front where the view is through the device."}},"gaps":[{"what":"Where a SOCOM suppressor's rear face stands on it (suppressor_seat_x)","need":"a photo of the device with a suppressor locked on, square from the side, or the suppressor's manual's drawing of the two together"},{"what":"Any diameter as the maker states it, and the photos' thin reading of a black part","need":"SureFire's drawing or product sheet (its host refuses the reader), or a straight photo with a scale in the part's plane"},{"what":"The inside: the thread's depth, the hole through, how the ports are drilled and what they open into","need":"a section drawing (the utility patents SureFire lists against WARCOMP-556, 8,459,406 and 10,274,278, may draw one), or photos straight into both ends"},{"what":"The upper left of the collar, which no straight view on file faces","need":"a photo square on its top or its left side: the six columns were counted from the upper right, where all show at once"}]},"sylvan-arms-sa5-pro-left-folder":{"id":"sylvan-arms-sa5-pro-left-folder","name":"SA5 Pro AR15 Folding Stock Adapter (Opens To The Left)","manufacturer":"Sylvan Arms","sku":"SA5P-L","url":"https://sylvanarms.com/product/sa5-pro-ar15-folding-stock-adapter/","category":"folding_adapter","description":"A hinge between the lower receiver and the buffer tube: the tube and stock swing to the rifle's left, \"off to the side with out the ejection port\" (Sylvan Arms), and lock straight again unfolded. It moves the tube back 1.45 to 1.50 in, and the bolt extension it comes with, in the carrier's tail, makes up the length. The maker: \"CNC-machined in the USA from 4140 Steel and only 9.4 ounces\", \"Adjustable Hinge Tension\", \"Improved and Hardened Buffer Pin\", \"2 QD attachment points\", \"Includes a 1045 Steel Bolt Extension\"; \"NOT COMPATIBLE WITH Tippmann 22, LWRC, Extar EP9\". Engraved on its stock half: \"Do Not Fire While Open\".","weight":"sylvan-arms-sa5-pro-left-folder.weight","occupies":[],"integral":[],"brings":[],"seats":{"receiver_extension":{"parentInterface":"tube_socket","interface":"receiver_thread","folds":true,"note":"The maker: \"Screw on, fold and carry!\"; the extension threads into the stock half (\"Standard 1-3/16” x 16 threading\"), and on the maker's photo of a rifle's right side (DSC08599) its end plate and castle nut are on against the stock half's rear face, as they would be on a receiver's."}},"requires":[],"folding":{"anchor":"hinge","moves":"stock_half","max":"sylvan-arms-sa5-pro-left-folder.fold_max","side":"left","inside":["carrier_extension"],"note":"Folds to the rifle's left. The maker: \"The direction of the fold is orientated to the direction as if your build was pointed down range. On a standard build, Folding to the RIGHT folds toward the ejection port. Folding to the LEFT folds off to the side with out the ejection port.\" Primary Arms: \"Folds to the left, away from the ejection port\". Engraved on the stock half: \"Do Not Fire While Open\" (Primary Arms' photo, SA5P-L_02)."},"anchors":{"receiver_thread":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the tube axis at the takedown pin's X, +x rearward (+z is then the rifle's left). Its front thread screws into the lower here as a tube would."},"tube_socket":{"origin":["{.added_length}",0,0],"x":[1,0,0],"note":"Where a receiver extension's own frame stands with the adapter on: the takedown pin's X moved back by the adapter's length. The stock half's rear face is the lower's rear face moved back as far."},"hinge":{"origin":["{.hinge_x}",0,"{.hinge_z}"],"x":[1,0,0],"y":[0,1,0],"note":"On the hinge bolt's axis, upright, low on the rifle's left (the knuckles from the blocks' top, 0.22 in under the tube's axis, down to the faces' bottom), in the plane where the two halves meet."}},"interfaces":{"receiver_thread":{"type":"ar15.buffer_tube_mount","role":"tube","anchor":"receiver_thread","params":{},"flips":false},"tube_socket":{"type":"ar15.buffer_tube_mount","role":"receiver","anchor":"tube_socket","params":{},"flips":false}},"materials":{"body":{"label":"Adapter","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The two halves, their knuckles, the cover plate and the QD bosses: 4140 steel (\"CNC-machined in the USA from 4140 Steel\", the maker). No page on file names its finish, or a colour but black (MidwayUSA's page title, \"Gen 5 Left Hand Black\", read by the discovery; the page refuses the harvester): drawn under the catalog's finish for steel whose maker names none (data/finishes.yaml, `steel`), in its black, not fitted. The photos show one flat dark grey with no hard highlight: lit flats read #454040 to #54504f (AR15Discounts' 307151.png, Primary Arms' SA5P-L_01), faces toward the lens under a soft light #322f2f (SA5P-L_02, the distributor's IQSA5PR-1). Sold in black only."},"hardware":{"label":"Castle nut, collar, button and bolt extension","finish":"nitride","recolorable":false,"color":"steel-nitride-black","note":"A glossier black than the halves on every photo (the castle nut on the maker's DSC08599 carries the light in a line): the castle nut on the front thread, the hinge bolt's head, the knurled tension collar, the release button's head and the bolt extension (\"1045 Steel\", the maker). No page names their finish: drawn under `nitride` for its look, a polished black on steel, which isn't fitted to a photo."}},"components":{},"geometry":{"components":{"receiver_half":"sylvan-arms-sa5-pro-left-folder.receiver_half.glb","stock_half":"sylvan-arms-sa5-pro-left-folder.stock_half.glb","carrier_extension":"sylvan-arms-sa5-pro-left-folder.carrier_extension.glb"},"approximations":["Each half's section is drawn from the ledger's figures, not traced: a ring about the bore (.ring_r, read on Primary Arms' rear view rectified by the stock half's threaded bore) carried down flat-sided to the mating faces' bottom (.body_bottom_below_axis) with rounded corners (.corner_r), as Primary Arms' open view shows the two mating faces. The stock half narrows from that section at the seam to its rear face's teardrop (the ring and a lobe about the large hole, joined by tangents: .lobe_centre_below_axis, .lobe_r), a ruled surface between the two, as the distributor's view from behind and right shows its right face leaning in below the logo; where along the half the lean begins isn't read, and it is drawn from the seam.","Below the rings, toward the rifle's left, each half carries a block out to the hinge's axis, the whole height from .block_top_below_axis under the bore down to the faces' bottom, as the closed part from behind and left shows them (87600342169f: the hinge column at the seam with a block ahead of it and one behind); the knuckles stand round beyond the blocks' faces. The receiver half's block runs its half's length; how far the stock half's reaches back isn't read (.stock_block_length, assumed).","Where the halves meet is the hinge's plane: opened flat their two mating faces lie in one plane (e6285ca2177b). The lengths along the bore (the castle nut, the receiver half, the stock half) are the maker's side photo of a rifle's right side read at the scale of the length the maker says it adds; the part's height on the same photo agrees to 1.3%.","The front thread is a 1 3/16-16 helix (lib.thread_x) between the receiver extension's roots and crests, from where a tube's front face stands in the lower (std.receiver_extension.front_face_x) back to the receiver half; its bore is the tube's (what the carrier runs in), widening to .receiver_bore_d through the half. The stock half's threaded bore is the same thread in a hole, between the crests as read and the extension's major diameter.","The castle nut on the front thread bears on the lower's rear face (the maker's DSC08599: no end plate between). Its outside diameter is read from its top edge beside the body's; its notches are four at 90 degrees, a quarter turn apart as two are seen from each of two opposite corners (not counted on a view of the whole turn), their width and depth assumed.","On the receiver half's right face: the cover plate (a rounded strip from the bore's height down past the button), the release button's round head at its lower end and the QD socket's boss low by the seam, each where the maker's side photo has it; how far each stands out of the face is assumed (the ledger). The button is drawn as it is with the stock locked open; Primary Arms' open view has its pin pushed out, as it is to fold.","The stock half's rear face has its four holes (the large one in the lobe, the second QD point; two middle ones; a small one by the left middle hole) where its rectified photo has them, blind, as deep as assumed.","The hinge: an upright bolt on the axis .hinge_z out on the rifle's left, its top and bottom knuckles the receiver half's, the knurled tension collar between them the stock half's (\"Adjustable Hinge Tension\"), all .knuckle_d across, at the heights Primary Arms' open view has them; the bolt's socket head in a shallow counterbore in the top knuckle's top (its head's and socket's sizes read on the same view; how far it is sunk, its height and the socket's depth assumed), drawn with the receiver half. Each half's block is cut round the axis where the other's knuckle or the collar turns: the collar sits in a window between the knuckles, as on the photos.","The bolt extension is turned from the distributor's photo of it standing beside the adapter, at the scale that makes what stands behind its shoulder the length the adapter adds: its O-ring end in the carrier's tail, its shoulder on the tail's rear end where the carrier stands in battery (std.ar15.upper_rear_face_x), its body with its two grooves, its neck and its foot reaching back to where the buffer then rests. The O-rings in its three grooves stand flush and aren't drawn apart from it.","The mating faces, seen when folded, as Primary Arms' open view has them: the stock half's locking tab (its end face's size read, its height off the face read along the photo's depth, good to a twentieth of an inch) and the receiver half's slot for it, drawn as one pocket that takes in both the tab's place and the slot's as read (0.08 in apart); on the receiver half's face a socket screw in a counterbore, a large hex socket and a round hole, blind, as deep as assumed.","Not drawn: the engravings (\"Do Not Fire While Open\", the SA logo), the hardened buffer pin at the stock half's bore and the small screw beside it, the round socket in the receiver half's front face below the thread (AR15Discounts' 307151.png sees it only obliquely: not placed), the QD sockets' detent balls, the collar's knurl, and the faces' small chamfers beyond a 0.012 in break."],"ledger":["sylvan-arms-sa5-pro-left-folder.added_length","sylvan-arms-sa5-pro-left-folder.hinge_x","sylvan-arms-sa5-pro-left-folder.hinge_z","sylvan-arms-sa5-pro-left-folder.length","sylvan-arms-sa5-pro-left-folder.width","sylvan-arms-sa5-pro-left-folder.height"]},"profiles":{},"gaps":[{"what":"A square side view of the part, and one from above: the lengths along the bore rest on one lifestyle photo of a rifle at the scale of the maker's range for the length added, and the hinge's place across on a three-quarter view opened flat.","need":"A side photo of the part alone or on a lower with its pins in frame; a photo from above, folded and open."},{"what":"Its finish: no page names it.","need":"The maker's or a seller's word for the coating (nitride, phosphate, Cerakote, DLC)."},{"what":"Which two of its sockets are the maker's \"2 QD attachment points\": the boss out of the right face, the large hole in the stock half's rear lobe and a round socket in the receiver half's front face below the thread are all on the photos.","need":"The manual, or a photo of a sling swivel in it."},{"what":"Whether the 9.4 oz includes the bolt extension, and the extension's own size: it is scaled here by the length it makes up.","need":"A seller's or the maker's figure for the extension's length, diameter or weight."},{"what":"The User Manual tab on the maker's page is restricted to the reader; no instructions, drawing or patent number is on file.","need":"The manual (a PDF the maker or a seller hosts), or a patent number on the part or its page."},{"what":"MidwayUSA's page (1026993741) refuses the harvester (403); Shiner Tactical's is gone (410).","need":"Nothing: the maker's, Primary Arms' and AR15Discounts' pages give the figures."}]},"sylvan-arms-sa5-pro-right-folder":{"id":"sylvan-arms-sa5-pro-right-folder","name":"SA5 Pro AR15 Folding Stock Adapter (Opens To The Right)","manufacturer":"Sylvan Arms","sku":"SA5P-R","url":"https://sylvanarms.com/product/sa5-pro-ar15-folding-stock-adapter/","category":"folding_adapter","description":"A hinge between the lower receiver and the buffer tube: the tube and stock swing to the rifle's right, \"toward the ejection port\" (Sylvan Arms), and lock straight again unfolded. It moves the tube back 1.45 to 1.50 in, and the bolt extension it comes with, in the carrier's tail, makes up the length. The maker: \"CNC-machined in the USA from 4140 Steel and only 9.4 ounces\", \"Includes a 1045 Steel Bolt Extension\"; \"NOT COMPATIBLE WITH Tippmann 22, LWRC, Extar EP9\"; asked about the right-folding one beside a forward assist and a shell deflector: \"As long as the shell deflector is standard Mil-spec size or smaller, there is no interference.\"","weight":"sylvan-arms-sa5-pro-right-folder.weight","occupies":[],"integral":[],"brings":[],"seats":{"receiver_extension":{"parentInterface":"tube_socket","interface":"receiver_thread","folds":true,"note":"The maker: \"Screw on, fold and carry!\"; the extension threads into the stock half (\"Standard 1-3/16” x 16 threading\"), its end plate and castle nut on against the stock half's rear face as on a receiver's (the maker's DSC08599, of the left-folding one)."}},"requires":[],"folding":{"anchor":"hinge","moves":"stock_half","max":"sylvan-arms-sa5-pro-right-folder.fold_max","side":"right","inside":["carrier_extension"],"note":"Folds to the rifle's right. The maker: \"The direction of the fold is orientated to the direction as if your build was pointed down range. On a standard build, Folding to the RIGHT folds toward the ejection port.\" AR15Discounts: \"Folds to the right for optimal compatibility with your setup\"."},"anchors":{"receiver_thread":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the tube axis at the takedown pin's X, +x rearward (+z is then the rifle's left). Its front thread screws into the lower here as a tube would."},"tube_socket":{"origin":["{.added_length}",0,0],"x":[1,0,0],"note":"Where a receiver extension's own frame stands with the adapter on: the takedown pin's X moved back by the adapter's length."},"hinge":{"origin":["{.hinge_x}",0,"-{.hinge_z}"],"x":[1,0,0],"y":[0,1,0],"note":"On the hinge bolt's axis, upright, low on the rifle's RIGHT (-z here), in the plane where the two halves meet: the left-folding one's mirrored."}},"interfaces":{"receiver_thread":{"type":"ar15.buffer_tube_mount","role":"tube","anchor":"receiver_thread","params":{},"flips":false},"tube_socket":{"type":"ar15.buffer_tube_mount","role":"receiver","anchor":"tube_socket","params":{},"flips":false}},"materials":{"body":{"label":"Adapter","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The two halves, their knuckles, the cover plate and the QD bosses: 4140 steel (\"CNC-machined in the USA from 4140 Steel\", the maker). No page on file names its finish, or a colour but black (MidwayUSA's page title for the left-folding one, \"Gen 5 Left Hand Black\", read by the discovery; the page refuses the harvester): drawn under the catalog's finish for steel whose maker names none (data/finishes.yaml, `steel`), in its black, not fitted. The photos show one flat dark grey with no hard highlight: lit flats read #454040 to #54504f (AR15Discounts' 307151.png, Primary Arms' SA5P-L_01), faces toward the lens under a soft light #322f2f (SA5P-L_02, the distributor's IQSA5PR-1). Sold in black only."},"hardware":{"label":"Castle nut, collar, button and bolt extension","finish":"nitride","recolorable":false,"color":"steel-nitride-black","note":"A glossier black than the halves on every photo (the castle nut on the maker's DSC08599 carries the light in a line): the castle nut on the front thread, the hinge bolt's head, the knurled tension collar, the release button's head and the bolt extension (\"1045 Steel\", the maker). No page names their finish: drawn under `nitride` for its look, a polished black on steel, which isn't fitted to a photo."}},"components":{},"geometry":{"components":{"receiver_half":"sylvan-arms-sa5-pro-right-folder.receiver_half.glb","stock_half":"sylvan-arms-sa5-pro-right-folder.stock_half.glb","carrier_extension":"sylvan-arms-sa5-pro-right-folder.carrier_extension.glb"},"approximations":["No photo on file shows the right-folding one; the maker: \"Folding to the RIGHT folds toward the ejection port.\" It is drawn as the left-folding one's mirror across the bore's vertical plane: the hinge, its knuckles and blocks on the rifle's right, and with them the cover plate, the release button and the QD boss on its left face, the rear face's holes mirrored. Whether the maker moves the button, the plate and the QD boss to the other side, or keeps them where they are, isn't known.","Every size is the left-folding one's (its part file's approximations say how each was read and what is assumed): the ring about the bore and its flat sides, the stock half narrowing to its rear face's teardrop, the hinge's blocks and knuckles, the front thread and its castle nut, the threaded bore, the rear face's holes, the bolt extension.","Not drawn: the engravings, the latch, slot, screws and pins on the mating faces, the hardened buffer pin, the QD sockets' detent balls, the collar's knurl, and the faces' small chamfers beyond a 0.012 in break."],"ledger":["sylvan-arms-sa5-pro-right-folder.added_length","sylvan-arms-sa5-pro-right-folder.hinge_x","sylvan-arms-sa5-pro-right-folder.hinge_z","sylvan-arms-sa5-pro-right-folder.length","sylvan-arms-sa5-pro-right-folder.width","sylvan-arms-sa5-pro-right-folder.height"]},"profiles":{},"gaps":[{"what":"Any photo of the right-folding one: the sellers' pictures for SA5P-R (AR15Discounts' 307151.png, Monadnock's IQSA5PR-1) show the left one, and the maker's gallery has only the left one.","need":"A photo of the right-folding one: its right side with the hinge, or a rifle folded to the right."},{"what":"Everything the left-folding one lacks (its gaps): a square side view, the finish's name, whether the 9.4 oz has the bolt extension in it, the manual.","need":"As the left one's."},{"what":"Primary Arms and MidwayUSA list only the left one; AR15Discounts has the right one out of stock.","need":"Nothing: the maker's, AR15Discounts' and Monadnock's pages give its figures."}]},"taurus-tx22-barrel-46":{"id":"taurus-tx22-barrel-46","name":"TX22 4.6 in Threaded Barrel","manufacturer":"Taurus","url":"https://shoptaurus.com/new-items/taurustx-22-toro-conversion-kit","category":"pistol_barrel","description":"The T.O.R.O.'s barrel: alloy steel, matte black, 4.6 in, threaded 1/2x28 with a 1:10 right-hand twist (Taurus: \"Thread Pitch: 1/2x28 • Twist Rate: 1:10 RH Twist\"). Taurus sells it with the T.O.R.O. slide as the conversion kit for the newer TX22 frames.","weight":"taurus-tx22-barrel-46.weight","barrelLength":"taurus-tx22-barrel-46.stated_length","cartridge":{"takes":[".22 LR"],"stated":"Caliber: .22 LR","source":"https://shoptaurus.com/new-items/taurustx-22-toro-conversion-kit (Taurus shop's specifications for the kit, as cached: harvest.quote; Sportsman's Warehouse: \"Cartridge 22 Long Rifle\")"},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"slide":{"origin":[0,0,0],"note":"Barrel frame: origin at its breech face on the bore axis, +x toward the muzzle."},"muzzle":{"origin":["{.shoulder_x}",0,0],"note":"The thread's shoulder, where a muzzle device seats."}},"interfaces":{"slide":{"type":"tx22.barrel","role":"barrel","anchor":"slide","params":{},"flips":false,"note":"It comes off the frame with the slide (Taurus shop's picture of the conversion kit)."},"muzzle":{"type":"muzzle_thread","role":"barrel","anchor":"muzzle","params":{"thread":"1/2-28","thread_length":"={.thread_length}"},"flips":false,"note":"Taurus shop: \"Thread Pitch: 1/2x28\" and \"Threaded Barrel for Suppressor Use – 4.6-inch barrel with threaded muzzle allows suppressor or muzzle device installation.\"; Sportsman's: \"Thread Pitch 1/2 x 28\". Its threaded length is on no page: worked out from the published barrel length and where the shoulder stands (thread_length)."}},"materials":{"barrel":{"label":"Barrel","finish":"phosphate","recolorable":false,"color":"steel-phosphate-black","note":"Gun Tests (Taurus's table): \"BARREL MATERIAL Alloy Steel BARREL FINISH Matte Black\"; Taurus shop: \"Barrel Finish: Matte Black\". A matte black steel, drawn in the catalog's black phosphate (fitted to BCM's gas block, not to this barrel: the chamber block in the right view is a dark grey with \"22 LR\" lit on it). Not drawn: the \"22 LR\" on the block's right face and the other marks."}},"components":{},"geometry":{"model":"taurus-tx22-barrel-46.glb","components":{},"approximations":["Its rear is a rectangular chamber block, where it shows in the slide's open middle section: its top read on both black side views (0.31 over the bore), its front end at the slide's nose, its rear end at the breech face, which is worked out from the published 4.6 in, the protector's front wall (assumed) and the protector's front face where the pistol's published 7.60 in puts it. Its width (0.58) and its bottom (0.3 under the bore, the slide's lower edge) are assumed.","The round barrel is a bull barrel at an assumed 0.55 in (none of its silhouette shows: the slide's nose hides it, the vents its middle only), from the block to the thread's shoulder, which stands at the slide's front face, where the protector goes out of sight in both side views.","The muzzle thread is a helix, 28 to the inch, between the minor and major diameters of a 1/2-28 thread (the Army barrel's, Taurus naming no class), right-hand (assumed: as its rifling's twist), over its length worked out from the barrel's published length (0.47), running out at the shoulder over its last pitch; the bore one plain hole right through, at another .22 LR barrel's reading.","Not drawn: the chamber, the extractor's cut, the rifling, the crown, whatever under the block bears on the frame, the marks."],"ledger":["taurus-tx22-barrel-46.stated_length","taurus-tx22-barrel-46.shoulder_x","taurus-tx22-barrel-46.thread_length","taurus-tx22-barrel-46.od","taurus-tx22-barrel-46.block_top"]},"profiles":{},"gaps":[{"what":"The round barrel's diameter, the chamber block's width and what is under it","need":"A photo of the barrel out of the slide (a seller's of Taurus's replacement barrel, or the conversion kit's other pictures)"},{"what":"The thread's length","need":"A page that gives it, or the barrel bare from the side"}]},"taurus-tx22-frame":{"id":"taurus-tx22-frame","name":"TX22 Gen 2 frame","manufacturer":"Taurus","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/handguns/taurus-tx22-gen-2-toro-22-long-rifle-46in-hard-anodized-black-pistol-221-rounds/p/1883977","category":"pistol_frame","weight":"taurus-tx22-frame.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"slide":{"origin":["{.slide_rear_x}","{.bore_axis_y}",0],"note":"Where a closed slide's rear face stands, on the bore axis: the slide's origin."},"magwell":{"origin":["{.magwell_x}","{.grip_bottom_y}",0],"note":"Where a seated magazine's base pad bears on the grip's bottom face, at the front of its body, on the mid-plane, +x toward the muzzle and +y up (the pistol's own axes: the magazine is built as it stands in the grip, leaning back by magwell_rake)."},"rear":{"origin":["{.rear_x}",0,0],"note":"The frame's rearmost point (the back of the grip low down): where the overall length begins."},"grip":{"origin":["{.grip_x}","{.grip_y}",0],"note":"The middle of the grip, where the firing hand holds it: midway between the front and back straps, midway down the grip, on the mid-plane."},"rail":{"origin":["{.rail_slot0_x}","{.rail_top_y}",0],"x":[1,0,0],"y":[0,-1,0],"note":"The rail under the dust cover, its face (down) at its rear slot's centre: +y out of the rail's face, downward, +x toward the muzzle."}},"interfaces":{"slide":{"type":"tx22.slide","role":"frame","anchor":"slide","params":{},"flips":false},"magwell":{"type":"tx22.magwell","role":"frame","anchor":"magwell","params":{},"flips":false},"rail":{"type":"picatinny","role":"rail","anchor":"rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}"},"flips":false,"under":true,"note":"Sportsman's: \"MIL-STD-1913 accessory rail\"; American Rifleman: \"The dustcover features a molded-in 1.75\\\" accessory rail.\" Two slots, on the standard's pitch."}},"materials":{"body":{"label":"Frame","finish":"polymer","recolorable":false,"color":"placeholder-polymer-black","sheen":"matte","note":"Gun Tests: \"FRAME MATERIAL Polymer FRAME FINISH Black\"; American Rifleman: \"Frame: matte-black polymer\". The black polymer in the catalog's placeholder black, as the other black polymer parts on file are (no fit of Taurus's black: a black isn't fitted, D81). Sold with other frames (Primary Arms: \"black, FDE, OD Green, and Cyan splatter frames\"; Blackstone's OD green T.O.R.O., 725327943365, is the OD green frame's side view on file): other items under other numbers, not offered here."},"panels":{"label":"Grip panels","finish":"polymer","recolorable":false,"color":"placeholder-polymer-black","sheen":"matte","detail":"stipple","note":"The grip's stippled sides (the close view of the grip, 0c6d81d099f9, and Blackstone's side view), sunk a little below their smooth borders; the frame's polymer with a generated stipple."},"controls":{"label":"Controls","finish":"nitride","recolorable":false,"color":"placeholder-black","note":"The manual safety's two levers, the slide stop, the disassembly latch's ends and the magazine release's buttons: black, with a metal's lit edges in every photo (Sportsman's close view of the rear, b2ff2ae9a5cd). No page names their material or finish: a black metal by their look."},"trigger":{"label":"Trigger","finish":"polymer","recolorable":false,"color":"placeholder-polymer-black","note":"Sportsman's: \"Taurus Performance Trigger System\". Black in every photo, flat-faced, its pin's bright end on its side; no page names its material."},"pins":{"label":"Cross pins","finish":"nitride","recolorable":false,"color":"steel-nitride-black","note":"The two cross pins' ends on each side of the frame: dark in Sportsman's photos of the black pistol (a black steel's end in its ring), not bright. No page names them: black nitride steel by their look."},"trigger_pin":{"label":"Trigger pin","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"The trigger's pin, its end on each side of the trigger: bright in both side views (Sportsman's left, Blackstone's right). No page names it."}},"components":{},"geometry":{"model":"taurus-tx22-frame.glb","components":{},"approximations":["Its side outline is Blackstone's right side of an OD green T.O.R.O. (another item number than the black 1-2TX22P141: the same Gen 2 frame in another colour), framed by the two cross pins and checked against Sportsman's left view of the black one (profiles.left: IoU 0.94; their heel's lowest points 0.1 in apart, the left view nearer the lens). Blackstone's view is taken from 11 to 13 degrees above: the edges traced are its near face's, as the pins are, and stand where they should; what stands nearer the middle plane reads higher, and is moved to the near-level left view's reading: the trigger guard's lower bar (its foot 0.07 in, the opening's floor 0.13, which is the far edge of the bar's top face in that view: guard_bar_top_y, guard_bar_bottom_y) and the trigger (0.07, trigger_drop). The trigger's tip reads 0.1 in further forward in Blackstone's view than in the left one (another pistol's trigger at rest): not moved along.","No view on file is square across the frame. Its width under the slide is the slide's (0.93, read by the slide's owner in the right oblique against the thread protector's face: the slide's side runs down into the frame's with no ledge in both obliques), and the safety's levers stand out of it to the published widest point (1.25: 0.16 each). The grip is as wide as the 22-round magazine's sleeve (1.115), which Taurus's own picture of it seated has flush with the grip's foot (Handguns' view of the 16-round's pad from below has the pad a hair proud), from its foot up its panels, easing to the frame's width between y -0.95 and -0.45. ASSUMED: the trigger guard's bars 0.40 across, the trigger 0.30; the grip's front and back straps rounded across by 0.30, the dust cover's front corners and the tang by 0.06; the well's walls whatever the magazine's own size leaves (its width, depth and lean are the magazine's: taurus-tx22-magazine-16.body_width, body_front_to_back, rake 12.1 degrees for the front strap's 14.5; its front where Blackstone's photo has the pad's nose less the magazine's own overhang, magwell_x); the panels sunk 0.012 under their borders, the finger's indentations 0.03, the dust cover's lower band stepped in 0.04; the other controls standing out 0.05.","The dust cover's front has a room for the slide's front lug (the slide's own figures: its length, the lug's length, width and reach below the bore, a 0.005 clearance round), open to the top: the frame's front face is a U round the lug and the recoil spring's head in both obliques.","The guard's two bars are cut to their width under the opening's floor and ahead of its front wall, each easing out to the frame's width over a half cosine: the lower bar into the grip's front strap (x 0 to 0.9), the front bar into the dust cover (over its top 0.27 in). How the real guard flares into either no view shows from the front.","The rail is MIL-STD-1913's head (lib.rail_head) turned down under the dust cover, its face at the photo's reading (rail_top_y), from its front tooth back the published 1.75 in, its two slots at the standard's size on its pitch from the photo's rear slot; the dust cover's underside beside it at the line the photo shows (dust_cover_bottom_y).","The controls are their right-side outlines (Blackstone's), mirrored for the left (the safety is ambidextrous; the disassembly latch and the magazine release show on both sides in Sportsman's two views), each a flat plate standing out of the side face; the slide stop's lever is the left view's outline, on the left only. Their bevels and ridges aren't drawn.","The grip's bottom face over the magazine's pad is drawn on the seat's line (through magwell_x, grip_bottom_y at the pad's top's rise of 1.0 degree: the same edge in the same photo, and the frame's own grip_bottom_low on it), from the heel's front face to where the face rounds up into the front strap: as traced it stood level, a hundredth over the pad's top along its middle (a slit of backdrop under both magazines). The heel and the front round are as traced.","The grip: its stippled sides (the texture's extent in Blackstone's view) sunk a little under their borders, in the panels' slot, with the two smooth raised bands that part them into the back strip, the middle panel and the front strip left at the surface; the straps' faces fore and aft in the panels' slot over the same height (the right oblique shows the front strap stippled). The magazine well is cut through from the grip's foot to the frame's top, along the magazine's own lean, to its own depth and width with a clearance round its back and sides and none at its front. The tang's traced back (behind x -2.6, over y -0.35), where the OD green meets the slide's black, is smoothed over a 0.03 in window: drawn as traced its pixel steps read as ridges across the tang.","Not drawn: the frame's top under the slide (its walls, the rails' tabs, the disassembly latch's housing, the ejector: Taurus's picture of the frame with the slide off shows them, from close by and too much in perspective to read; nothing of the frame stands above the slide's lower edge), the raised borders inside the grip's panels and the bull's head, the line inside the dust cover's lower band, the slide stop's pocket, the bull's head in the panel, the markings, a flare at the magazine well's mouth."],"ledger":["taurus-tx22-frame.bore_axis_y","taurus-tx22-frame.slide_rear_x","taurus-tx22-frame.rear_x","taurus-tx22-frame.grip_bottom_y","taurus-tx22-frame.magwell_x","taurus-tx22-frame.width","taurus-tx22-frame.body_width","taurus-tx22-frame.grip_width","taurus-tx22-frame.guard_width","taurus-tx22-frame.magwell_across"]},"profiles":{"side":{"plane":"xy","origin":"the centre of the frame's rear cross pin (D104), x along the slide's travel (the slide's lower edge)","offset":{},"points":[[-2.895,-3.45],[-2.888,-3.897],[-2.864,-4.041],[-2.839,-4.078],[-2.827,-4.081],[-2.82,-4.119],[-2.749,-4.185],[-2.661,-4.228],[-2.564,-4.252],[-2.531,-4.247],[-2.531,-4.219],[-2.459,-4.045],[-2.19,-4.046],[-2.14,-4.026],[-1.427,-4.023],[-1.255,-4.009],[-1.252,-3.99],[-1.215,-3.993],[-1.183,-4.011],[-1.127,-4.014],[-0.911,-3.962],[-0.855,-3.933],[-0.831,-3.908],[-0.804,-3.9],[-0.802,-3.825],[-0.821,-3.806],[-0.821,-3.778],[-0.843,-3.766],[-0.849,-3.725],[-0.856,-3.663],[-0.851,-3.572],[-0.83,-3.515],[-0.821,-3.453],[-0.808,-3.437],[-0.8,-3.368],[-0.787,-3.349],[-0.742,-3.155],[-0.712,-3.064],[-0.7,-2.989],[-0.691,-2.979],[-0.612,-2.684],[-0.6,-2.612],[-0.591,-2.603],[-0.579,-2.531],[-0.558,-2.474],[-0.558,-2.446],[-0.533,-2.38],[-0.534,-2.352],[-0.435,-2.226],[-0.419,-2.182],[-0.417,-2.113],[-0.437,-2.004],[-0.426,-1.863],[-0.398,-1.791],[-0.336,-1.69],[-0.296,-1.652],[-0.285,-1.625],[-0.236,-1.6],[-0.223,-1.578],[-0.195,-1.575],[-0.167,-1.555],[-0.133,-1.552],[-0.12,-1.539],[-0.039,-1.526],[0.074,-1.534],[0.23,-1.586],[0.422,-1.672],[0.551,-1.702],[2.015,-1.701],[2.117,-1.641],[2.15,-1.573],[2.146,-1.526],[2.127,-1.486],[2.097,-1.45],[2.07,-1.446],[2.067,-1.108],[2.084,-0.917],[2.102,-0.823],[2.169,-0.606],[2.182,-0.52],[3.368,-0.531],[3.385,-0.514],[3.388,-0.448],[3.411,-0.428],[3.558,-0.426],[3.585,-0.434],[3.598,-0.515],[3.618,-0.532],[3.769,-0.534],[3.782,-0.516],[3.788,-0.457],[3.808,-0.433],[3.965,-0.432],[3.976,-0.446],[3.976,-0.468],[3.998,-0.48],[4.002,-0.533],[4.009,-0.541],[4.044,-0.541],[4.061,-0.514],[4.079,-0.448],[4.112,-0.276],[4.131,-0.266],[4.134,-0.254],[4.127,-0.216],[4.142,-0.125],[4.134,0.025],[4.142,0.144],[4.081,0.157],[2.646,0.165],[-1.882,0.165],[-1.997,0.161],[-2.007,0.142],[-2.201,0.14],[-2.202,0.161],[-2.22,0.165],[-2.747,0.165],[-2.753,0.149],[-2.786,0.122],[-2.815,0.117],[-2.818,0.036],[-2.827,0.017],[-2.805,0.005],[-2.807,-0.092],[-2.824,-0.1],[-2.826,-0.08],[-2.837,-0.078],[-2.863,-0.124],[-2.853,-0.196],[-2.837,-0.218],[-2.769,-0.262],[-2.488,-0.291],[-2.387,-0.321],[-2.318,-0.327],[-2.309,-0.343],[-2.208,-0.37],[-2.142,-0.41],[-2.121,-0.407],[-2.116,-0.427],[-2.083,-0.441],[-2.081,-0.455],[-2.045,-0.49],[-2.024,-0.492],[-2.018,-0.523],[-1.996,-0.545],[-1.986,-0.604],[-1.973,-0.616],[-1.968,-0.779],[-1.981,-0.788],[-1.983,-0.864],[-2.005,-0.889],[-2.057,-1.064],[-2.124,-1.193],[-2.124,-1.209],[-2.226,-1.382],[-2.368,-1.58],[-2.547,-1.857],[-2.673,-2.099],[-2.731,-2.241],[-2.794,-2.47],[-2.854,-2.839],[-2.882,-3.115]],"features":{"guard_opening":[[[1.884,-1.444],[1.882,-1.175],[1.885,-1.172],[1.885,-1.147],[1.881,-1.144],[1.873,-0.95],[1.87,-0.947],[1.87,-0.919],[1.863,-0.894],[1.86,-0.841],[1.857,-0.838],[1.85,-0.784],[1.805,-0.61],[1.782,-0.588],[1.751,-0.579],[1.717,-0.579],[1.713,-0.576],[1.67,-0.573],[1.623,-0.564],[1.548,-0.559],[1.529,-0.553],[1.45,-0.55],[1.419,-0.544],[1.385,-0.545],[1.382,-0.542],[1.297,-0.536],[1.281,-0.524],[1.278,-0.514],[1.274,-0.455],[1.265,-0.455],[1.259,-0.465],[1.256,-0.515],[1.247,-0.524],[1.169,-0.519],[1.156,-0.512],[1.134,-0.513],[1.118,-0.507],[1.062,-0.504],[1.059,-0.501],[1.015,-0.498],[0.993,-0.492],[0.965,-0.492],[0.956,-0.486],[0.952,-0.474],[0.943,-0.474],[0.943,-0.48],[0.937,-0.486],[0.837,-0.487],[0.824,-0.481],[0.805,-0.481],[0.802,-0.478],[0.324,-0.483],[0.317,-0.505],[0.318,-0.52],[0.327,-0.533],[0.327,-0.558],[0.337,-0.561],[0.337,-0.576],[0.343,-0.582],[0.343,-0.595],[0.353,-0.614],[0.353,-0.657],[0.344,-0.695],[0.332,-0.714],[0.329,-0.727],[0.323,-0.73],[0.301,-0.764],[0.273,-0.79],[0.273,-0.799],[0.261,-0.815],[0.261,-0.821],[0.239,-0.846],[0.23,-0.849],[0.23,-0.856],[0.211,-0.875],[0.208,-0.884],[0.187,-0.909],[0.177,-0.925],[0.181,-0.941],[0.178,-0.972],[0.11,-1.057],[0.036,-1.167],[0.036,-1.183],[0.045,-1.189],[0.064,-1.195],[0.146,-1.241],[0.181,-1.257],[0.247,-1.297],[0.253,-1.297],[0.328,-1.34],[0.451,-1.401],[0.47,-1.407],[0.495,-1.423],[0.501,-1.423],[0.507,-1.429],[0.526,-1.435],[0.533,-1.441],[0.539,-1.441],[0.58,-1.463],[0.592,-1.462],[0.605,-1.469],[1.331,-1.462],[1.334,-1.465],[1.647,-1.462],[1.65,-1.465],[1.872,-1.466],[1.881,-1.46]]],"trigger":[[[0.339,-0.457],[0.327,-0.473],[0.317,-0.505],[0.318,-0.52],[0.327,-0.533],[0.327,-0.558],[0.337,-0.561],[0.337,-0.576],[0.343,-0.582],[0.343,-0.595],[0.353,-0.614],[0.35,-0.679],[0.329,-0.72],[0.329,-0.727],[0.323,-0.73],[0.301,-0.764],[0.273,-0.79],[0.273,-0.799],[0.261,-0.815],[0.261,-0.821],[0.242,-0.84],[0.246,-0.852],[0.394,-1.008],[0.533,-1.128],[0.716,-1.264],[0.782,-1.307],[0.829,-1.332],[0.838,-1.341],[0.845,-1.341],[0.851,-1.347],[0.885,-1.363],[0.929,-1.362],[0.948,-1.356],[1.051,-1.349],[1.082,-1.339],[1.095,-1.323],[1.095,-1.311],[1.104,-1.289],[1.1,-1.261],[1.059,-1.23],[0.993,-1.168],[0.917,-1.068],[0.882,-1.003],[0.876,-0.981],[0.86,-0.95],[0.86,-0.941],[0.844,-0.9],[0.831,-0.85],[0.827,-0.813],[0.821,-0.794],[0.82,-0.735],[0.817,-0.731],[0.819,-0.656],[0.826,-0.637],[0.825,-0.616],[0.832,-0.606],[0.84,-0.559],[0.868,-0.487],[0.837,-0.487],[0.824,-0.481],[0.78,-0.478],[0.749,-0.469],[0.671,-0.467],[0.658,-0.461],[0.627,-0.461],[0.605,-0.455],[0.477,-0.45],[0.473,-0.447],[0.408,-0.444],[0.405,-0.441],[0.37,-0.441]]],"safety_right":[[[-2.333,-0.144],[-2.326,-0.147],[-2.311,-0.147],[-2.308,-0.144],[-2.282,-0.147],[-2.27,-0.156],[-2.267,-0.165],[-2.239,-0.165],[-2.235,-0.171],[-2.207,-0.174],[-2.188,-0.183],[-2.129,-0.186],[-2.097,-0.192],[-2.041,-0.188],[-2.029,-0.185],[-2.026,-0.179],[-2.001,-0.179],[-1.998,-0.175],[-1.963,-0.172],[-1.948,-0.166],[-1.891,-0.159],[-1.882,-0.152],[-1.841,-0.146],[-1.835,-0.14],[-1.795,-0.136],[-1.785,-0.13],[-1.72,-0.12],[-1.71,-0.113],[-1.679,-0.11],[-1.67,-0.104],[-1.645,-0.103],[-1.617,-0.091],[-1.576,-0.087],[-1.526,-0.071],[-1.504,-0.071],[-1.479,-0.061],[-1.46,-0.061],[-1.426,-0.048],[-1.411,-0.048],[-1.364,-0.035],[-1.345,-0.035],[-1.301,-0.016],[-1.283,0.006],[-1.274,0.028],[-1.261,0.044],[-1.255,0.063],[-1.237,0.091],[-1.234,0.113],[-1.243,0.129],[-1.259,0.135],[-1.434,0.133],[-1.437,0.136],[-1.462,0.136],[-1.465,0.133],[-1.569,0.132],[-1.572,0.129],[-1.603,0.129],[-1.606,0.132],[-1.719,0.131],[-1.722,0.127],[-1.819,0.13],[-1.822,0.127],[-1.866,0.126],[-1.869,0.129],[-2.007,0.128],[-2.01,0.14],[-2.207,0.139],[-2.207,0.129],[-2.232,0.11],[-2.232,0.098],[-2.238,0.091],[-2.253,0.088],[-2.253,0.072],[-2.263,0.069],[-2.262,0.057],[-2.281,0.047],[-2.281,0.041],[-2.287,0.038],[-2.287,0.025],[-2.281,0.022],[-2.284,0],[-2.293,-0.009],[-2.303,-0.009],[-2.302,-0.019],[-2.318,-0.028],[-2.333,-0.053]]],"takedown_right":[[[1.27,-0.289],[1.163,-0.287],[1.16,-0.29],[0.951,-0.292],[0.938,-0.295],[0.932,-0.317],[0.933,-0.408],[0.936,-0.411],[0.936,-0.439],[0.943,-0.452],[0.943,-0.471],[0.952,-0.471],[0.959,-0.486],[0.965,-0.489],[0.993,-0.489],[0.996,-0.492],[1.04,-0.495],[1.062,-0.501],[1.118,-0.503],[1.134,-0.51],[1.156,-0.509],[1.169,-0.515],[1.253,-0.515],[1.253,-0.49],[1.259,-0.477],[1.259,-0.458],[1.265,-0.452],[1.274,-0.452],[1.276,-0.33],[1.273,-0.327]]],"magrelease_right":[[[-0.613,-0.992],[-0.629,-1.026],[-0.632,-1.051],[-0.644,-1.083],[-0.65,-1.12],[-0.662,-1.155],[-0.662,-1.202],[-0.655,-1.214],[-0.639,-1.23],[-0.614,-1.233],[-0.599,-1.239],[-0.58,-1.239],[-0.564,-1.245],[-0.545,-1.245],[-0.539,-1.251],[-0.517,-1.251],[-0.489,-1.26],[-0.455,-1.262],[-0.436,-1.269],[-0.373,-1.271],[-0.367,-1.277],[-0.335,-1.28],[-0.32,-1.286],[-0.273,-1.286],[-0.236,-1.254],[-0.229,-1.254],[-0.205,-1.216],[-0.192,-1.185],[-0.193,-1.169],[-0.18,-1.138],[-0.18,-1.125],[-0.174,-1.116],[-0.178,-1.069],[-0.2,-1.044],[-0.307,-1.017],[-0.335,-1.014],[-0.344,-1.008],[-0.41,-0.996],[-0.473,-0.978],[-0.485,-0.978],[-0.495,-0.972],[-0.507,-0.972],[-0.545,-0.96],[-0.582,-0.966],[-0.595,-0.973]]],"finger_index":[[[0.729,-0.06],[1.903,-0.049],[1.981,-0.079],[2.019,-0.135],[1.998,-0.261],[1.952,-0.355],[1.906,-0.393],[1.296,-0.399],[1.029,-0.301],[0.732,-0.304]]],"cover_band":[[[2.281,-0.336],[2.348,-0.198],[4.188,-0.181],[4.189,-0.341],[2.281,-0.358]]],"panels":[[[-1.997,-0.929],[-2.042,-1.077],[-2.11,-1.206],[-2.11,-1.221],[-2.264,-1.467],[-2.264,-1.479],[-2.279,-1.489],[-2.44,-1.722],[-2.48,-1.8],[-2.533,-1.87],[-2.548,-1.901],[-2.548,-1.936],[-2.573,-1.945],[-2.606,-2.005],[-2.72,-2.263],[-2.759,-2.391],[-2.795,-2.557],[-2.86,-3.027],[-2.879,-3.315],[-2.879,-3.662],[-2.854,-3.662],[-2.842,-3.634],[-2.798,-3.634],[-2.791,-3.649],[-2.751,-3.649],[-2.72,-3.639],[-2.689,-3.611],[-2.657,-3.61],[-2.629,-3.591],[-2.586,-3.585],[-2.58,-3.51],[-2.533,-3.506],[-2.529,-3.559],[-2.504,-3.562],[-2.504,-3.609],[-2.545,-3.612],[-2.544,-3.638],[-2.519,-3.672],[-2.443,-3.727],[-2.418,-3.727],[-2.415,-3.746],[-2.381,-3.767],[-2.352,-3.767],[-2.349,-3.792],[-2.317,-3.817],[-2.252,-3.819],[-2.168,-3.79],[-2.086,-3.78],[-1.612,-3.654],[-1.39,-3.583],[-1.331,-3.579],[-1.327,-3.633],[-1.339,-3.692],[-1.302,-3.723],[-1.242,-3.751],[-1.164,-3.762],[-1.104,-3.809],[-1.047,-3.811],[-1.003,-3.83],[-0.978,-3.83],[-0.944,-3.807],[-0.882,-3.804],[-0.872,-3.797],[-0.873,-3.769],[-0.86,-3.75],[-0.87,-3.688],[-0.856,-3.509],[-0.844,-3.503],[-0.835,-3.44],[-0.823,-3.421],[-0.823,-3.381],[-0.804,-3.346],[-0.726,-3.051],[-0.714,-2.951],[-0.702,-2.948],[-0.693,-2.923],[-0.687,-2.857],[-0.675,-2.848],[-0.548,-2.343],[-0.511,-2.283],[-0.449,-2.213],[-0.434,-2.17],[-0.451,-1.951],[-0.449,-1.891],[-0.427,-1.835],[-0.428,-1.794],[-0.415,-1.791],[-0.351,-1.678],[-0.31,-1.64],[-0.31,-1.615],[-0.326,-1.615],[-0.332,-1.627],[-0.436,-1.628],[-0.439,-1.606],[-0.461,-1.597],[-0.533,-1.589],[-0.551,-1.604],[-0.554,-1.648],[-0.607,-1.649],[-0.626,-1.665],[-0.635,-1.749],[-0.672,-1.803],[-0.686,-1.893],[-0.736,-1.9],[-0.74,-1.841],[-0.716,-1.772],[-0.713,-1.715],[-0.704,-1.712],[-0.698,-1.646],[-0.72,-1.618],[-0.724,-1.568],[-0.824,-1.529],[-0.856,-1.488],[-0.919,-1.464],[-0.972,-1.464],[-0.985,-1.436],[-1.029,-1.434],[-1.076,-1.39],[-1.176,-1.35],[-1.422,-1.224],[-1.45,-1.218],[-1.51,-1.178],[-1.679,-1.105],[-1.692,-1.086],[-1.739,-1.087],[-1.751,-1.102],[-1.754,-1.14],[-1.788,-1.14],[-1.795,-1.156],[-1.838,-1.156],[-1.858,-1.1],[-1.877,-1.085],[-1.909,-0.972],[-1.934,-0.944],[-1.978,-0.945],[-1.984,-0.929]]],"panel_band_back":[[[-1.985,-0.879],[-1.886,-1.075],[-1.795,-1.416],[-2.182,-1.907],[-2.209,-1.976],[-2.508,-3.562],[-2.391,-3.602],[-2.112,-1.994],[-2.094,-1.975],[-1.708,-1.415],[-1.776,-1.162]]],"panel_band_front":[[[-0.737,-1.544],[-0.727,-1.593],[-0.771,-2.257],[-1.141,-3.549],[-1.218,-3.622],[-1.099,-3.621],[-1.062,-3.589],[-0.74,-2.179],[-0.648,-1.69],[-0.57,-1.623]]]},"scaleRefs":["taurus-tx22-frame.front_pin_x","taurus-tx22-frame.front_pin_y"],"inputs":{"taurus-tx22-frame.front_pin_x":1.355,"taurus-tx22-frame.front_pin_y":0.03,"taurus-tx22-frame.seam_y":0.165},"tolerance":0.006,"photo":"references/taurus-tx22-toro 9efc84da32c0 (Blackstone Shooting: a T.O.R.O. with an OD green frame from its right (2500 x 1844))","method":"manual polygon (825 points picked on the photo); frame from the reviewed holes rear_pin, front_pin (319.7 px/in, rms 0.000 in over 2 points); origin at the photo's frame; clipped to y max {taurus-tx22-frame.seam_y} = 0.165; Douglas-Peucker at 0.006 in with the extremes kept: 162 points (IoU 0.997 with the full outline); checks: x_min -2.895 ± 0.011 in vs taurus-tx22-frame.rear_x -2.894 ± 0.025 (provisional): agrees; x_max 4.142 ± 0.015; y_min -4.252 ± 0.015; y_max 0.173 ± 0.005; features through the same placement (guard_opening: The trigger guard's opening: the background inside the guard and the trigger in front of it below the frame's underside, less the disassembly latch, which hangs into it (.cache/tx22/taurus-tx22-frame/bsfeat.py); trigger: The trigger, black in the opening: its shoe below the frame's slot (its top goes up into the frame); safety_right: The manual safety's right lever, black on the frame's side under the slide; takedown_right: The disassembly latch's right end, black, hanging from the frame's underside into the guard's opening; magrelease_right: The magazine release's right button, black, behind the trigger guard; finger_index: The indentation on each side over the trigger guard (American Rifleman: \"Frame indentations, located above the square profile trigger guard, serve as index points for the trigger finger\"): its shadowed upper edge, rounded front end and lower edge picked on a 2x crop; cover_band: The dust cover's lower band, stepped in along each side above the rail from a slanted rear end to the front (its upper edge's shadow and its lower edge picked on a 2x crop; the line inside it isn't drawn); panels: The grip's stippled sides, above the smooth band round the grip's foot: where the surface's grey spreads over 12 levels in a 15 px window (.cache/tx22/taurus-tx22-frame/panels.py), below row 600 (the trigger guard's top), the largest piece, its contour at 2 px. The raised borders inside the panel (round the bull's head) aren't told apart.; panel_band_back: The smooth raised band down the grip's side between the stippled back strip and the middle panel: its two lit edges picked on a 1.6x crop of the grip's upper half and a 0.8x crop of the whole grip, from where it leaves the panel's top to where it meets the smooth band round the grip's foot; panel_band_front: The smooth raised band between the middle panel and the stippled front strip, picked as panel_band_back) (tools/trace.py)","via":"harvest","note":"The frame from its right, below the slide: the dust cover with its rail's two slots, the trigger guard and its opening, the grip with its heel round the magazine's base pad, the tang behind the slide. The controls and the trigger are not in it (black, other material slots of the model)."},"left":{"plane":"xy","origin":"the photo's frame","offset":{},"points":[[-2.917,-3.754],[-2.899,-3.95],[-2.905,-4.02],[-2.893,-4.032],[-2.899,-4.096],[-2.88,-4.134],[-2.886,-4.146],[-2.88,-4.171],[-2.842,-4.241],[-2.776,-4.301],[-2.687,-4.339],[-2.637,-4.352],[-2.542,-4.346],[-2.479,-4.352],[-2.475,-4.064],[-2.466,-4.055],[-0.928,-3.956],[-0.9,-3.94],[-0.925,-3.921],[-0.887,-3.883],[-0.893,-3.782],[-0.887,-3.725],[-0.785,-3.352],[-0.753,-3.194],[-0.741,-3.175],[-0.696,-2.979],[-0.677,-2.934],[-0.658,-2.833],[-0.633,-2.764],[-0.62,-2.707],[-0.626,-2.7],[-0.614,-2.681],[-0.582,-2.561],[-0.582,-2.523],[-0.55,-2.441],[-0.474,-2.353],[-0.455,-2.308],[-0.449,-2.264],[-0.474,-2.144],[-0.467,-2.062],[-0.474,-2.049],[-0.461,-1.992],[-0.404,-1.853],[-0.322,-1.758],[-0.331,-1.742],[-0.353,-1.733],[-0.331,-1.711],[-0.312,-1.717],[-0.293,-1.698],[-0.249,-1.685],[-0.192,-1.648],[-0.185,-1.654],[-0.166,-1.635],[-0.154,-1.641],[-0.141,-1.629],[-0.122,-1.629],[-0.109,-1.61],[-0.084,-1.603],[-0.072,-1.616],[-0.053,-1.597],[-0.034,-1.61],[-0.037,-1.6],[-0.027,-1.591],[0.004,-1.597],[0.008,-1.581],[0.023,-1.578],[0.049,-1.597],[0.074,-1.591],[0.087,-1.61],[0.106,-1.604],[0.169,-1.629],[0.396,-1.743],[0.498,-1.775],[0.555,-1.781],[1.162,-1.776],[1.168,-1.769],[1.902,-1.777],[1.978,-1.77],[2.066,-1.72],[2.095,-1.685],[2.076,-1.622],[2.032,-1.571],[2.019,-1.54],[2.02,-1.147],[2.045,-0.951],[2.077,-0.819],[2.153,-0.578],[2.169,-0.556],[2.327,-0.556],[2.334,-0.563],[2.384,-0.556],[2.441,-0.569],[3.32,-0.564],[3.342,-0.548],[3.355,-0.472],[3.384,-0.45],[3.396,-0.463],[3.409,-0.456],[3.425,-0.472],[3.444,-0.535],[3.488,-0.555],[3.478,-0.564],[3.447,-0.558],[3.453,-0.57],[3.542,-0.577],[3.719,-0.564],[3.735,-0.548],[3.747,-0.479],[3.757,-0.469],[3.789,-0.469],[3.811,-0.498],[3.826,-0.577],[3.896,-0.59],[3.94,-0.577],[3.984,-0.577],[4.007,-0.542],[4.019,-0.492],[4.032,-0.372],[4.042,-0.362],[4.061,-0.369],[4.121,-0.302],[4.172,-0.005],[4.178,0.165],[-2.786,0.165],[-2.774,0.149],[-2.799,0.136],[-2.863,-0.199],[-2.856,-0.256],[-2.818,-0.319],[-2.771,-0.348],[-2.727,-0.36],[-2.569,-0.373],[-2.316,-0.431],[-2.196,-0.469],[-2.113,-0.507],[-2.034,-0.58],[-2.003,-0.636],[-1.978,-0.725],[-1.984,-0.731],[-1.978,-0.807],[-1.997,-0.927],[-1.984,-0.978],[-2.01,-0.991],[-2.022,-1.054],[-2.041,-1.086],[-2.06,-1.155],[-2.079,-1.18],[-2.073,-1.193],[-2.098,-1.225],[-2.098,-1.25],[-2.117,-1.269],[-2.137,-1.32],[-2.162,-1.351],[-2.156,-1.364],[-2.194,-1.408],[-2.295,-1.585],[-2.415,-1.749],[-2.415,-1.762],[-2.479,-1.844],[-2.536,-1.952],[-2.574,-2.002],[-2.682,-2.204],[-2.764,-2.419],[-2.796,-2.565],[-2.809,-2.584],[-2.815,-2.66],[-2.84,-2.755],[-2.834,-2.767],[-2.853,-2.843],[-2.86,-2.938],[-2.885,-3.083],[-2.879,-3.102],[-2.898,-3.216],[-2.898,-3.305],[-2.911,-3.4],[-2.911,-3.596],[-2.917,-3.602],[-2.911,-3.615],[-2.917,-3.634],[-2.905,-3.665],[-2.911,-3.703],[-2.892,-3.722],[-2.902,-3.732],[-2.911,-3.729]],"features":{"slide_stop":[[[-0.395,0.057],[-0.767,0.067],[-0.815,-0.026],[-0.858,-0.121],[-0.847,-0.138],[-0.471,-0.139],[-0.411,-0.05]]]},"scaleRefs":["taurus-tx22-frame.front_pin_x","taurus-tx22-frame.front_pin_y"],"inputs":{"taurus-tx22-frame.front_pin_x":1.355,"taurus-tx22-frame.front_pin_y":0.03,"taurus-tx22-frame.seam_y":0.165},"tolerance":0.006,"photo":"references/taurus-tx22-toro f0237849b397 (Sportsman's Warehouse 1883977-2: the black T.O.R.O. from its left)","method":"luminance < 150, 1 polygons excluded, closing ×1, largest piece, holes up to 3000 px filled; frame from the reviewed holes rear_pin, front_pin (158.1 px/in, rms 0.000 in over 2 points); origin at the photo's frame; clipped to y max {taurus-tx22-frame.seam_y} = 0.165; Douglas-Peucker at 0.006 in with the extremes kept: 184 points (IoU 0.998 with the full outline); checks: x_min -2.917 ± 0.023 in vs taurus-tx22-frame.rear_x -2.894 ± 0.025 (provisional): agrees; x_max 4.634 ± 0.034; y_min -4.352 ± 0.032; features through the same placement (slide_stop: The slide stop's lever on the left, under the slide behind the trigger: its lit outline on an 8x crop (the pocket moulded round it isn't drawn)) (tools/trace.py)","via":"harvest","note":"The frame from its left (Sportsman's, the black T.O.R.O.), below the slide, the magazine's pad taken off: the check on Blackstone's outline, and the slide stop's lever, which only the left side has."}},"gaps":[{"what":"The frame's widths (under the slide, the grip, the trigger guard, the trigger) and how its straps round across","need":"A view of the pistol from the front and one from behind, square on, from 8 ft or more, zoomed; or the manual's exploded view (Taurus's PDF refuses the reader: a copy the user saves from their own browser)"},{"what":"The frame's top under the slide (the rails' tabs and walls, the latch's housing), seen only from close by","need":"The frame with the slide off, square from its side, from 8 ft or more, zoomed"},{"what":"The magazine well as it is (its walls, the flare at its mouth): drawn as the magazine's own size leaves it","need":"The grip's foot from below, square on, with the magazine out"}]},"taurus-tx22-magazine-16":{"id":"taurus-tx22-magazine-16","name":"TX22 .22 LR 16-Round Magazine","manufacturer":"Taurus","sku":"358-0017-01","url":"https://www.primaryarms.com/taurus-tx22lr-magazine-16-round","category":"pistol_magazine","description":"Taurus's standard magazine for the full-size TX22, the T.O.R.O. among them: the flush one, its pad level under the grip. Taurus sells its body with a +6 sleeve as the 22-round (taurus-tx22-magazine-22).","weight":"taurus-tx22-magazine-16.weight","cartridge":{"takes":[".22 LR"],"stated":"Taurus TX22 .22 LR 16-Round Magazine - Black (358-0017-01-WB)","source":"https://shoptaurus.com/tx22-22lr-22rd-magazine-assembly-web (Taurus's own shop, the page's title as cached: harvest.quote)"},"rounds":{"capacity":"taurus-tx22-magazine-16.capacity","each":"std.cartridge_22lr.weight"},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"magwell":{"origin":[0,0,0],"note":"Where the pad's top meets the front of the body, on the mid-plane: what bears on the grip's bottom face at the frame's magwell_x, grip_bottom_y. The magazine is built as it stands in the grip (the pistol's own axes): its pad level, its body leaning forward by the rake, the pad's top rising pad_top_rise toward the muzzle along the grip's bottom face."}},"interfaces":{"magwell":{"type":"tx22.magwell","role":"magazine","anchor":"magwell","params":{},"flips":false}},"materials":{"body":{"label":"Magazine body","finish":"polymer","recolorable":false,"color":"placeholder-polymer-black","sheen":"matte","note":"Taurus: \"Constructed from impact-resistant black polymer\" and \"Impact-Resistant Polymer Body\" (its shop's page for 358-0017-01-WB); Primary Arms: \"durable black polymer construction\"; Galati: \"constructed from polymer with a steel internal spring. Features a polymer follower and polymer base plate\". KYGUNCO's table says \"Material Steel\", against the maker's words. Sold in black only (no other colour on any page on file). A black polymer: not fitted to a photo (the catalog's polymer black). The follower's buttons are the follower's polymer (black in every picture), drawn in this slot."},"pad":{"label":"Base pad","finish":"polymer","recolorable":false,"color":"placeholder-polymer-black","sheen":"matte","note":"Galati: \"polymer base plate\"; black in every picture."}},"components":{},"geometry":{"model":"taurus-tx22-magazine-16.glb","components":{},"approximations":["No page gives a size. The scale is the pad's length, adopted from what the magazine has to fit (base_pad_length's `release`, 1.630 in: its catch notch at the height of the frame's release button), beside the pad as it shows under Blackstone's OD green grip on the frame's rail (1.763, 8% longer: kept, and in the gaps). At the seated scale the top stood 0.26 in over the bore's axis inside the slide and the pad was wider than the pistol's published widest point; at this one the top is 0.10 under the bore's axis and the pad 1.19 wide. Every side view of the magazine alone (six) agrees on its proportions to 2 to 3%; the body (taken on Gun Mag Warehouse's square view of the 22-round, whose body Taurus says it is) is 1.185 in front to back, 0.64 across, 4.39 tall over the pad's top.","The body is its side outline crossed with its section (the 22-round's end view, a picture turned some 5 degrees: its left half mirrored, the faces' middle found from the left edge and body_width), built in its own axis and leaning by the rake; the lips' taper from the end view, the gap between them its notch.","Hollow inside a staggered column of rounds' room (inside_width by inside_length, assumed: American Rifleman, of the TX22's magazines, \"more ammunition capacity than traditional single-stack designs\") up to follower_depth under the top (assumed): the follower and the lips of an empty magazine are solid. The long slot, its round lower end and the small slot go through both walls; the follower's button stands button_proud (assumed) out of its hole at the slot's top on each side; the catch's notch is a pocket catch_notch_depth (assumed) into each side; the channel down each side ahead of the slot, groove_depth (assumed) deep.","The pad: its side as it shows seated (Blackstone), its nose's highlights' jitter taken out, its rear end square where the grip's heel covers it; its top the grip's bottom face (a line through the origin, rising pad_top_rise); its plan from below (Primary Arms), its nose pad_front_ahead ahead of the body's front; the lip that wraps the front strap swept round the plan's rounded front, dying into the top at its ends.","On the pad's underside: the ring round its plug and the dimple near its nose, where the view from below has them (their depths assumed). Not drawn: the moulded markings ('TAURUS TX', 'CAL .22 LR', '1'), the pad's bull's head, the spring."],"ledger":["taurus-tx22-magazine-16.overall_height","taurus-tx22-magazine-16.below_grip","taurus-tx22-magazine-16.base_pad_length","taurus-tx22-magazine-16.pad_width","taurus-tx22-magazine-16.pad_front_ahead","taurus-tx22-magazine-16.pad_top_rise","taurus-tx22-magazine-16.rake","taurus-tx22-magazine-16.body_front_to_back","taurus-tx22-magazine-16.body_across","taurus-tx22-magazine-16.body_width","taurus-tx22-magazine-16.inside_width","taurus-tx22-magazine-16.inside_length","taurus-tx22-magazine-16.follower_depth","taurus-tx22-magazine-16.button_proud","taurus-tx22-magazine-16.catch_notch_depth","taurus-tx22-magazine-16.groove_depth","taurus-tx22-magazine-16.plug_ring_depth","taurus-tx22-magazine-16.dimple_depth"]},"profiles":{"side":{"plane":"xy","origin":"the pad's front tip (its foremost point on its lowest rows) and its lowest point: the pad's own corner; the part's origin (the body's front at the pad's top) is found from it by the model's script","offset":{},"points":[[-1.663,0.12],[-1.663,0.017],[-1.64,0],[-1.131,0],[-0.487,0.013],[-0.307,0.032],[-0.112,0.082],[-0.038,0.129],[-0.008,0.176],[-0.005,0.249],[-0.088,0.401],[-0.165,0.441],[-0.339,0.47],[-0.346,0.487],[0.523,4.533],[0.458,4.535],[0.453,4.553],[0.434,4.553],[0.409,4.647],[0.342,4.706],[0.278,4.719],[0.144,4.696],[0.096,4.735],[0.038,4.738],[0.021,4.726],[-0.004,4.669],[-0.123,4.645],[-0.137,4.657],[-0.14,4.689],[-0.17,4.722],[-0.622,4.698],[-0.665,4.663],[-0.668,4.597],[-0.728,4.285],[-1.515,0.516],[-1.534,0.432],[-1.54,0.425],[-1.548,0.436],[-1.582,0.414],[-1.599,0.384],[-1.642,0.239],[-1.642,0.173],[-1.66,0.152],[-1.652,0.136]],"scaleRefs":["taurus-tx22-magazine-16.base_pad_length"],"inputs":{"taurus-tx22-magazine-16.base_pad_length":1.63},"tolerance":0.008,"photo":"references/taurus-tx22-magazine-22 fb7549e66665 (Gun Mag Warehouse, the 16-round from its right (2000 x 2000), standing on its pad, the front at the right)","method":"luminance < 225, closing ×2, largest piece, holes filled; scale from taurus-tx22-magazine-16.base_pad_length = 1.63 in (median width over 0.94–0.985 of the height from the top, 574–622 px 618 px → 378.9 px/in); origin at x max, y min of the outline (x over 0.94–0.985 of the height from the top); Douglas-Peucker at 0.008 in with the extremes kept: 44 points (IoU 0.996 with the full outline) (tools/trace.py)","via":"harvest","note":"The 16-round's whole side as it stands on a level pad; its pad is the model's (the body is the square picture's: profiles.body)."},"body":{"plane":"xy","origin":"the body's front where it meets the sleeve's top edge (level once turned to the rake): the 16-round's pad's top at the body's front, the part's origin","offset":{},"points":[[-1.22,0.006],[-1.207,0],[0,0.037],[-0.016,0.068],[0.014,0.215],[0.156,0.844],[0.486,2.414],[0.591,2.868],[0.633,3.098],[0.893,4.246],[0.865,4.26],[0.825,4.257],[0.795,4.303],[0.77,4.32],[0.573,4.355],[0.511,4.413],[0.464,4.434],[0.425,4.422],[0.363,4.353],[0.25,4.331],[0.239,4.347],[0.239,4.399],[0.223,4.416],[0.201,4.421],[-0.234,4.403],[-0.268,4.39],[-0.285,4.359],[-0.821,1.823]],"features":{"slot":[[[-0.904,0.269],[-0.882,0.321],[-0.848,0.348],[-0.831,0.379],[-0.143,3.593],[-0.103,3.61],[0.055,3.578],[0.066,3.561],[-0.045,3.028],[-0.634,0.315],[-0.608,0.248],[-0.614,0.192],[-0.654,0.138],[-0.683,0.119],[-0.72,0.104],[-0.761,0.101],[-0.83,0.121],[-0.86,0.144],[-0.896,0.199]]],"button_hole":[[[-0.074,3.902],[-0.065,3.945],[-0.041,3.98],[0.003,4.013],[0.034,4.024],[0.083,4.014],[0.108,3.998],[0.132,3.967],[0.144,3.913],[0.116,3.778],[0.093,3.762],[0.058,3.758],[0.02,3.766],[-0.04,3.807],[-0.068,3.85]]],"small_slot":[[[-0.31,3.803],[-0.25,4.063],[-0.218,4.093],[-0.208,4.077],[-0.22,3.989],[-0.263,3.782],[-0.279,3.771],[-0.29,3.774]]],"catch_notch":[[[0.44,3.002],[0.598,2.969],[0.577,2.866],[0.419,2.898]]],"groove":[[[0.329,4.193],[0.422,4.174],[-0.408,0.161],[-0.501,0.18]]]},"scaleRefs":["taurus-tx22-magazine-16.body_front_to_back"],"angleRef":"taurus-tx22-magazine-16.rake","inputs":{"taurus-tx22-magazine-16.body_front_to_back":1.185,"taurus-tx22-magazine-16.rake":12.119},"tolerance":0.006,"photo":"references/taurus-tx22-magazine-22 c468e0cbc9ec (Gun Mag Warehouse, the 22-round from its right (1280 x 1280), the body upright, square on: its body above the sleeve)","method":"luminance < 225, 1 polygons excluded, closing ×2, largest piece, holes filled; rotated -11.7° (counter-clockwise) so the edges' mean lean in the band 0.15–0.85 of the height (0.4° rear, 0.5° front in the photo) becomes taurus-tx22-magazine-16.rake = 12.119°; re-measured 12.1°/12.2°; scale from taurus-tx22-magazine-16.body_front_to_back = 1.185 in (median width over 0.25–0.75 of the height from the top, 213–214 px 213 px → 180.1 px/in); origin at x max, y min of the outline (x over 0.985–1.0 of the height from the top); Douglas-Peucker at 0.006 in with the extremes kept: 28 points (IoU 0.996 with the full outline); features through the same placement (slot: the long slot through both walls, the follower's button's track, with its round lower end: the backdrop seen through it, flood-filled from a pixel inside; button_hole: the round opening at the slot's top, where the follower's button stands when the magazine is empty (the 16-round's pictures have the button in it, on both sides); small_slot: the short slot near the top of the rear strip, through both walls; catch_notch: the magazine catch's notch in the side, at the front edge: a dark rectangle in the side face; groove: the channel down the side just ahead of the slot, from the lips (where it opens into their notch) to the sleeve: its dark floor (columns 650 to 660) and the lit walls either side (645, 662), the groove as wide as both together; picked on a tile enlarged four times with its pixel grid (.cache/tx22/taurus-tx22-magazine-22/body_mid_grid.png, body_top_grid.png)) (tools/trace.py)","via":"harvest","note":"The body above the grip's bottom face, as it stands in the grip: leaning forward by the rake."},"pad":{"plane":"xy","origin":"the photo's frame","offset":{},"points":[[-5.951,-3.661],[-5.942,-3.658],[-5.913,-3.598],[-5.905,-3.608],[-5.92,-3.664],[-5.897,-3.672],[-5.264,-3.704],[-4.885,-3.713],[-4.586,-3.704],[-4.41,-3.672],[-4.321,-3.644],[-4.266,-3.616],[-4.218,-3.577],[-4.188,-3.527],[-4.189,-3.519],[-4.208,-3.535],[-4.215,-3.527],[-4.212,-3.512],[-4.194,-3.496],[-4.199,-3.486],[-4.208,-3.492],[-4.216,-3.484],[-4.204,-3.466],[-4.231,-3.444],[-4.238,-3.429],[-4.229,-3.416],[-4.239,-3.424],[-4.247,-3.417],[-4.241,-3.41],[-4.253,-3.398],[-4.25,-3.389],[-4.275,-3.383],[-4.254,-3.352],[-4.26,-3.343],[-4.246,-3.319],[-4.277,-3.347],[-4.348,-3.382],[-4.548,-3.43],[-4.579,-3.43],[-4.603,-3.415],[-4.687,-3.415],[-4.693,-3.428],[-4.791,-3.429],[-4.844,-3.438],[-4.856,-3.432],[-5.171,-3.447],[-5.519,-3.443],[-5.525,-3.428],[-5.541,-3.428],[-5.584,-3.435],[-5.608,-3.46],[-5.868,-3.455],[-5.887,-3.488]],"scaleRefs":["std.picatinny.slot_pitch"],"inputs":{"std.picatinny.slot_pitch":0.394},"tolerance":0.006,"photo":"references/taurus-tx22-toro 9efc84da32c0 (Blackstone Shooting's T.O.R.O. with an OD green frame from its right (2500 x 1844), square on: the 16-round's black pad under the grip)","method":"luminance < 80, inside [100, 1640, 760, 1812], 1 polygons excluded, closing ×2, largest piece, holes filled; frame from the reviewed holes slot_rear, slot_front (324.2 px/in, rms 0.000 in over 2 points); origin at the photo's frame; Douglas-Peucker at 0.006 in with the extremes kept: 53 points (IoU 0.982 with the full outline); the pad's top is where the grip's bottom edge, a dark line, ends over it (the triangle the grip has moulded over its bottom edge is left out by a polygon); the pad's rear end shows under the grip's rear skirt (tools/trace.py)","via":"harvest","note":"The seated pad's side as it shows under the grip, in the photo's own frame (the rail's rear slot's middle at the origin, x along the rail): the model's script puts it in the part's frame by its nose and pad_front_ahead, and by the grip's bottom edge over the body's front."},"plan":{"plane":"xz","origin":"the pad's nose (its foremost point), on the mid-plane (the middle of its width)","offset":{},"points":[[-1.63,-0.369],[-1.622,-0.504],[-1.617,-0.524],[-1.6,-0.539],[-1.209,-0.581],[-0.759,-0.593],[-0.45,-0.578],[-0.3,-0.517],[-0.217,-0.461],[-0.136,-0.384],[-0.056,-0.256],[-0.016,-0.135],[0,0],[0,0.02],[-0.028,0.186],[-0.079,0.303],[-0.16,0.41],[-0.26,0.492],[-0.347,0.538],[-0.445,0.572],[-0.688,0.589],[-0.944,0.593],[-1.341,0.575],[-1.557,0.556],[-1.593,0.544],[-1.609,0.487],[-1.616,0.399]],"features":{"plug":[[[-0.782,0.098],[-0.57,0.098],[-0.57,-0.112],[-0.782,-0.112]]],"plug_face":[[[-0.765,0.081],[-0.587,0.081],[-0.587,-0.095],[-0.765,-0.095]]],"dimple":[[[-0.269,0.038],[-0.204,0.038],[-0.204,-0.033],[-0.269,-0.033]]]},"scaleRefs":["taurus-tx22-magazine-16.base_pad_length"],"inputs":{"taurus-tx22-magazine-16.base_pad_length":1.63},"tolerance":0.006,"photo":"references/taurus-tx22-magazine-16 7ebe9ab55fee (Primary Arms 358-0017-01_03, the pad from below (2200 x 1467), the front at the right)","method":"luminance < 225, closing ×2, largest piece, holes filled; scale from taurus-tx22-magazine-16.base_pad_length = 1.63 in (x-extent 1742 px → 1068.7 px/in); origin at x max, y center of the outline; Douglas-Peucker at 0.006 in with the extremes kept: 27 points (IoU 0.993 with the full outline); features through the same placement (plug: the round plug in the middle of the pad's underside (its latch): the dark ring round it at its outer edge; picked on the photo with its pixel grid (.cache/tx22/taurus-tx22-magazine-16/plan_plug_grid.png); plug_face: the plug's own face inside that ring; dimple: the small round dimple near the nose) (tools/trace.py)","via":"harvest","note":"The pad's plan: the outline of its underside, which is its widest."},"end":{"plane":"zy","origin":"the left edge of the 22-round's base plate's face (the faces' middles are taurus-tx22-magazine-22.sleeve_width / 2 to its right), at the top of the magazine","offset":{},"points":[[0,-6.087],[0.012,-6.104],[0.012,-6.116],[0,-6.139],[0.026,-6.154],[0.102,-6.148],[0.12,-6.165],[0.172,-6.165],[0.184,-6.154],[0.26,-6.154],[0.272,-6.165],[0.324,-6.165],[0.336,-6.171],[0.342,-6.165],[0.406,-6.165],[0.418,-6.154],[0.441,-6.154],[0.453,-6.165],[0.488,-6.16],[0.5,-6.171],[0.529,-6.171],[0.535,-6.177],[0.546,-6.171],[0.581,-6.183],[0.593,-6.177],[0.698,-6.177],[0.704,-6.171],[0.716,-6.177],[0.728,-6.171],[0.733,-6.177],[0.763,-6.177],[0.768,-6.183],[0.815,-6.183],[0.821,-6.177],[0.891,-6.177],[0.909,-6.171],[0.92,-6.16],[0.961,-6.177],[1.043,-6.177],[1.067,-6.16],[1.119,-6.16],[1.154,-6.13],[1.178,-6.142],[1.204,-6.127],[1.221,-6.098],[1.216,-6.092],[1.227,-6.081],[1.233,-6.04],[1.245,-6.016],[1.239,-5.999],[1.245,-5.993],[1.245,-5.964],[1.251,-5.958],[1.251,-5.736],[1.245,-5.73],[1.245,-5.648],[1.233,-5.631],[1.233,-5.134],[1.227,-5.128],[1.227,-5.099],[1.233,-5.093],[1.233,-5.011],[1.239,-5.005],[1.239,-4.859],[1.233,-4.853],[1.233,-4.801],[1.227,-4.795],[1.221,-4.737],[1.186,-4.643],[1.186,-4.544],[1.192,-4.538],[1.186,-4.532],[1.186,-4.287],[1.166,-4.266],[1.143,-4.254],[1.02,-4.214],[0.999,-4.187],[0.999,-3.609],[0.993,-3.603],[0.993,-3.486],[0.999,-3.474],[0.993,-3.468],[0.993,-0.342],[0.929,-0.167],[0.915,-0.164],[0.903,-0.169],[0.888,-0.155],[0.792,0],[0.763,0],[0.739,-0.023],[0.704,-0.023],[0.657,-0.064],[0.637,-0.073],[0.637,-0.091],[0.617,-0.117],[0.558,-0.117],[0.552,-0.123],[0.538,-0.108],[0.555,-0.079],[0.555,-0.067],[0.543,-0.056],[0.543,-0.003],[0.529,0],[0.5,-0.012],[0.476,-0.035],[0.459,-0.041],[0.418,-0.076],[0.397,-0.085],[0.374,-0.131],[0.345,-0.219],[0.327,-0.248],[0.316,-0.295],[0.298,-0.324],[0.292,-0.354],[0.281,-0.371],[0.281,-0.383],[0.269,-0.4],[0.24,-0.482],[0.24,-0.856],[0.245,-0.862],[0.245,-2.031],[0.251,-2.037],[0.257,-4.269],[0.245,-4.281],[0.24,-4.304],[0.169,-4.374],[0.146,-4.409],[0.117,-4.479],[0.094,-4.55],[0.094,-4.567],[0.067,-4.593],[0.056,-4.593],[0.035,-4.614],[0.023,-4.672],[0.018,-4.678],[0.018,-4.702],[0.012,-4.707],[0.012,-5.73],[0.006,-5.742],[0.012,-5.748],[0.012,-5.765],[0.006,-5.771],[0.006,-5.859],[0.018,-5.87],[0.006,-5.882],[0.006,-6.075]],"scaleRefs":["taurus-tx22-magazine-22.axis_height"],"inputs":{"taurus-tx22-magazine-22.axis_height":6.183},"tolerance":0.004,"photo":"references/taurus-tx22-magazine-22 25b0a3efc4e2 (Taurus shop 08, the 22-round from one end (1200 x 1200), standing on its base plate, turned some 5 degrees)","method":"luminance < 225, closing ×2, largest piece, holes filled; scale from taurus-tx22-magazine-22.axis_height = 6.183 in (y-extent 1058 px → 171.1 px/in); origin at x min, y max of the outline; Douglas-Peucker at 0.004 in with the extremes kept: 146 points (IoU 0.999 with the full outline) (tools/trace.py)","via":"harvest","note":"The body's section square across it (its rows above the 22-round's sleeve are this body's); the right edge carries a strip of the side (the picture is turned 5 degrees): the model mirrors the left half."}},"gaps":[{"what":"Every size of it: no page (Taurus's shop, a seller's, a review's) gives one; the sellers' 8.5 in and their weights are a carton's","need":"Taurus's figures (its manual's parts page, its own site, which refuses the reader), or a review that measures the magazine"},{"what":"Its size: drawn at the scale the catch and the release button give (1.630 in of pad), which also puts its top under the bore and its pad inside the pistol's published width; the pad the pistol's own photos show is 1.73 to 1.76 long (Blackstone's on the rail's pitch, the frame's pins, Sportsman's left view), 8% longer than this magazine's pad at this scale. Either the pistol was photographed with another pad than the sellers' 358-0017-01, or the six pictures of the magazine alone mislead together (no sign of it: square, from four sellers and Taurus)","need":"A picture of the magazine beside the pistol, or out of it in a picture with something of known size in its plane; or Taurus's figures"},{"what":"Its weight: worked out from the model's polymer (the inside assumed)","need":"Taurus's figure or a review's weighing"}]},"taurus-tx22-magazine-22":{"id":"taurus-tx22-magazine-22","name":"TX22 .22LR 22-round magazine","manufacturer":"Taurus","sku":"358-0034-00","url":"https://shoptaurus.com/new-items/taurus-tx22-22lr-magazine-22-rounds","category":"pistol_magazine","description":"The 16-round's body with Taurus's +6 extension under it: a sleeve that stands below the grip by its whole height, its front face on the front strap's line (Taurus's photo of it seated), its base plate square to the body.","weight":"taurus-tx22-magazine-22.weight","cartridge":{"takes":[".22 LR"],"stated":"Genuine Taurus TX22 .22LR 22-round magazine","source":"https://shoptaurus.com/new-items/taurus-tx22-22lr-magazine-22-rounds (Taurus's own shop, the page's title as cached: harvest.quote)"},"rounds":{"capacity":"taurus-tx22-magazine-22.capacity","each":"std.cartridge_22lr.weight"},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"magwell":{"origin":[0,0,0],"note":"Where the sleeve's top meets the front of the body, on the mid-plane: what bears on the grip's bottom face at the frame's magwell_x, grip_bottom_y. Built as it stands in the grip: the body (the 16-round's) leaning forward by its rake, the sleeve's base square to the body (Gun Mag Warehouse's view: the magazine stands on it with its body upright), so tilting down toward the muzzle."}},"interfaces":{"magwell":{"type":"tx22.magwell","role":"magazine","anchor":"magwell","params":{},"flips":false}},"materials":{"body":{"label":"Magazine body","finish":"polymer","recolorable":false,"color":"placeholder-polymer-black","sheen":"matte","note":"Taurus: \"This factory magazine uses the same body as the standard TX22 16-round magazine with a +6 round extension\" (its shop's page); the 16-round's body is \"impact-resistant black polymer\" in Taurus's words (taurus-tx22-magazine-16). Rifle Configurator: \"Polymer body, steel internals\"; Primary Arms' table \"Material Steel\" and Shooting Surplus' \"The body is steel\" stand against the maker's. Sold in black only. A black polymer: not fitted to a photo."},"sleeve":{"label":"Extension sleeve","finish":"polymer","recolorable":false,"color":"placeholder-polymer-black","sheen":"matte","note":"The +6 extension (Taurus's words); black, its textured panel the same black in every picture. Moulded polymer by its look (no page names its material)."},"base":{"label":"Base plate","finish":"polymer","recolorable":false,"color":"placeholder-polymer-black","sheen":"matte","note":"The plate under the sleeve, its parting line across the sleeve's foot (Gun Mag Warehouse's side view, Taurus's end view); black."}},"components":{},"geometry":{"model":"taurus-tx22-magazine-22.glb","components":{},"approximations":["No page gives a size: the scale is the 16-round's body (its pad's length as the catch and the release button give it, base_pad_length's adopted `release`), on the square view of this magazine (Gun Mag Warehouse's right side) turned to the 16-round's rake; its length along the body (6.18 in) then scales Taurus's end view, which gives the sleeve's width (1.12 in) once the 5 degrees it is turned are taken out. Seated, its top stands 0.10 in under the bore's axis, as the 16-round's does.","The body is the 16-round's construction (taurus_tx22_magazine.py): side outline crossed with the end view's section, hollow, its slot, small slot and the button's hole through (no button shows in this magazine's pictures), the catch's notch, the channel down each side.","The sleeve: the side under its top edge (drawn bearing on the grip's bottom face, the 16-round's pad's top line through the seat: the square view has it falling 1.9 degrees to the rear, 0.02 in lower at its rear end, a reading kept in the manifest) crossed with the end view's rows from the sleeve down, hollow (sleeve_wall, assumed); on each side the face under its diagonal edge set in by step_depth and the textured panel by panel_depth more (both assumed); the base plate under the parting line, solid, its underside flat.","Not drawn: the moulded markings ('CAL .22 LR'), the panel's texture, the sleeve's end faces' recessed panels and the notches at the base plate's corners (Taurus's end view), the spring."],"ledger":["taurus-tx22-magazine-22.overall_height","taurus-tx22-magazine-22.below_grip","taurus-tx22-magazine-22.axis_height","taurus-tx22-magazine-22.sleeve_length","taurus-tx22-magazine-22.sleeve_width","taurus-tx22-magazine-22.body_width","taurus-tx22-magazine-22.inside_width","taurus-tx22-magazine-22.inside_length","taurus-tx22-magazine-22.sleeve_wall","taurus-tx22-magazine-22.follower_depth","taurus-tx22-magazine-22.catch_notch_depth","taurus-tx22-magazine-22.step_depth","taurus-tx22-magazine-22.panel_depth","taurus-tx22-magazine-22.groove_depth"]},"profiles":{"side":{"plane":"xy","origin":"the base plate's front lower corner as the magazine stands in the grip (turned to the rake, its base square to the body tilts down to the front); the part's origin (the body's front at the sleeve's top) is found from it by the model's script","offset":{},"points":[[-1.544,0.314],[-1.526,0.274],[-1.386,0.239],[-0.36,0.021],[-0.149,0],[-0.096,0.006],[-0.04,0.043],[0,0.239],[-0.008,0.257],[0.052,0.545],[0.332,1.706],[0.303,1.744],[0.221,1.761],[0.074,1.763],[0.063,1.765],[0.049,1.793],[0.551,4.139],[0.657,4.593],[0.699,4.823],[0.959,5.971],[0.931,5.985],[0.89,5.982],[0.86,6.028],[0.835,6.045],[0.638,6.08],[0.577,6.138],[0.53,6.159],[0.491,6.147],[0.428,6.078],[0.316,6.056],[0.305,6.072],[0.304,6.123],[0.288,6.141],[0.266,6.145],[-0.168,6.128],[-0.202,6.115],[-0.22,6.084],[-1.099,1.968],[-1.155,1.725],[-1.188,1.703],[-1.203,1.661],[-1.229,1.644],[-1.29,1.458],[-1.45,0.714],[-1.521,0.451],[-1.516,0.422]],"features":{"slot":[[[-0.839,1.994],[-0.817,2.046],[-0.783,2.073],[-0.765,2.103],[-0.078,5.318],[-0.037,5.335],[0.12,5.302],[0.131,5.286],[0.021,4.753],[-0.569,2.04],[-0.543,1.972],[-0.549,1.917],[-0.588,1.863],[-0.618,1.843],[-0.655,1.828],[-0.695,1.825],[-0.765,1.845],[-0.794,1.868],[-0.831,1.924]]],"button_hole":[[[-0.008,5.627],[0.001,5.67],[0.025,5.705],[0.069,5.738],[0.099,5.749],[0.148,5.739],[0.173,5.722],[0.198,5.692],[0.21,5.638],[0.181,5.502],[0.158,5.487],[0.124,5.483],[0.086,5.491],[0.026,5.532],[-0.002,5.574]]],"small_slot":[[[-0.244,5.528],[-0.185,5.788],[-0.153,5.818],[-0.142,5.802],[-0.155,5.714],[-0.197,5.507],[-0.214,5.496],[-0.225,5.499]]],"catch_notch":[[[0.506,4.727],[0.663,4.694],[0.642,4.591],[0.484,4.623]]],"groove":[[[0.395,5.918],[0.487,5.898],[-0.343,1.886],[-0.435,1.905]]],"panel":[[[-1.163,0.825],[-0.064,1.148],[-0.22,0.341],[-0.722,0.433]]],"step":[[[-1.135,0.904],[-0.007,1.261],[-0.221,0.228],[-1.232,0.437]]],"base":[[[-1.516,0.518],[0.034,0.198],[-0.023,-0.08],[-1.573,0.241]]]},"scaleRefs":["taurus-tx22-magazine-16.body_front_to_back"],"angleRef":"taurus-tx22-magazine-16.rake","inputs":{"taurus-tx22-magazine-16.body_front_to_back":1.185,"taurus-tx22-magazine-16.rake":12.119},"tolerance":0.006,"photo":"references/taurus-tx22-magazine-22 c468e0cbc9ec (Gun Mag Warehouse, the 22-round from its right (1280 x 1280), the body upright, square on)","method":"luminance < 225, closing ×2, largest piece, holes filled; rotated -11.7° (counter-clockwise) so the edges' mean lean in the band 0.1–0.6 of the height (0.4° rear, 0.5° front in the photo) becomes taurus-tx22-magazine-16.rake = 12.119°; re-measured 12.1°/12.2°; scale from taurus-tx22-magazine-16.body_front_to_back = 1.185 in (median width over 0.15–0.6 of the height from the top, 213–215 px 213 px → 180.1 px/in); origin at x max, y min of the outline (x over 0.96–1.0 of the height from the top); Douglas-Peucker at 0.006 in with the extremes kept: 46 points (IoU 0.996 with the full outline); features through the same placement (slot: the long slot through both walls (the 16-round's body's); button_hole: the round opening at the slot's top: on this magazine no button shows in it; small_slot: the short slot near the top of the rear strip, through both walls; catch_notch: the magazine catch's notch in the side, at the front edge; groove: the channel down the side just ahead of the slot, from the lips (where it opens into their notch) to the sleeve: its dark floor (columns 650 to 660) and the lit walls either side (645, 662), the groove as wide as both together; picked on a tile enlarged four times with its pixel grid (.cache/tx22/taurus-tx22-magazine-22/body_mid_grid.png, body_top_grid.png); panel: the moulded panel on the sleeve's side, textured: a pointed quadrilateral, its upper edge parallel to the step above it (picked on a tile enlarged three times with its pixel grid, .cache/tx22/taurus-tx22-magazine-22/sleeve_grid.png); step: the sleeve's side below the diagonal edge that runs from its rear groove up to the front (from 557, 1050 to 742, 947), behind its front strip, down to the base plate's parting line (its lower edge a few pixels past it: the sleeve's cut stops at the line): the face the panel is in; base: the base plate under the sleeve: the parting line across at row 1134) (tools/trace.py)","via":"harvest","note":"The whole 22-round as it stands in the grip, leaning by the rake: the body, the sleeve and the base plate under it."},"end":{"plane":"zy","origin":"the left edge of the base plate's face (the faces' middles are sleeve_width / 2 to its right), at the top of the magazine","offset":{},"points":[[0,-6.087],[0.012,-6.104],[0.012,-6.116],[0,-6.139],[0.026,-6.154],[0.102,-6.148],[0.12,-6.165],[0.172,-6.165],[0.184,-6.154],[0.26,-6.154],[0.272,-6.165],[0.324,-6.165],[0.336,-6.171],[0.342,-6.165],[0.406,-6.165],[0.418,-6.154],[0.441,-6.154],[0.453,-6.165],[0.488,-6.16],[0.5,-6.171],[0.529,-6.171],[0.535,-6.177],[0.546,-6.171],[0.581,-6.183],[0.593,-6.177],[0.698,-6.177],[0.704,-6.171],[0.716,-6.177],[0.728,-6.171],[0.733,-6.177],[0.763,-6.177],[0.768,-6.183],[0.815,-6.183],[0.821,-6.177],[0.891,-6.177],[0.909,-6.171],[0.92,-6.16],[0.961,-6.177],[1.043,-6.177],[1.067,-6.16],[1.119,-6.16],[1.154,-6.13],[1.178,-6.142],[1.204,-6.127],[1.221,-6.098],[1.216,-6.092],[1.227,-6.081],[1.233,-6.04],[1.245,-6.016],[1.239,-5.999],[1.245,-5.993],[1.245,-5.964],[1.251,-5.958],[1.251,-5.736],[1.245,-5.73],[1.245,-5.648],[1.233,-5.631],[1.233,-5.134],[1.227,-5.128],[1.227,-5.099],[1.233,-5.093],[1.233,-5.011],[1.239,-5.005],[1.239,-4.859],[1.233,-4.853],[1.233,-4.801],[1.227,-4.795],[1.221,-4.737],[1.186,-4.643],[1.186,-4.544],[1.192,-4.538],[1.186,-4.532],[1.186,-4.287],[1.166,-4.266],[1.143,-4.254],[1.02,-4.214],[0.999,-4.187],[0.999,-3.609],[0.993,-3.603],[0.993,-3.486],[0.999,-3.474],[0.993,-3.468],[0.993,-0.342],[0.929,-0.167],[0.915,-0.164],[0.903,-0.169],[0.888,-0.155],[0.792,0],[0.763,0],[0.739,-0.023],[0.704,-0.023],[0.657,-0.064],[0.637,-0.073],[0.637,-0.091],[0.617,-0.117],[0.558,-0.117],[0.552,-0.123],[0.538,-0.108],[0.555,-0.079],[0.555,-0.067],[0.543,-0.056],[0.543,-0.003],[0.529,0],[0.5,-0.012],[0.476,-0.035],[0.459,-0.041],[0.418,-0.076],[0.397,-0.085],[0.374,-0.131],[0.345,-0.219],[0.327,-0.248],[0.316,-0.295],[0.298,-0.324],[0.292,-0.354],[0.281,-0.371],[0.281,-0.383],[0.269,-0.4],[0.24,-0.482],[0.24,-0.856],[0.245,-0.862],[0.245,-2.031],[0.251,-2.037],[0.257,-4.269],[0.245,-4.281],[0.24,-4.304],[0.169,-4.374],[0.146,-4.409],[0.117,-4.479],[0.094,-4.55],[0.094,-4.567],[0.067,-4.593],[0.056,-4.593],[0.035,-4.614],[0.023,-4.672],[0.018,-4.678],[0.018,-4.702],[0.012,-4.707],[0.012,-5.73],[0.006,-5.742],[0.012,-5.748],[0.012,-5.765],[0.006,-5.771],[0.006,-5.859],[0.018,-5.87],[0.006,-5.882],[0.006,-6.075]],"scaleRefs":["taurus-tx22-magazine-22.axis_height"],"inputs":{"taurus-tx22-magazine-22.axis_height":6.183},"tolerance":0.004,"photo":"references/taurus-tx22-magazine-22 25b0a3efc4e2 (Taurus shop 08, the 22-round from one end (1200 x 1200), standing on its base plate, turned some 5 degrees)","method":"luminance < 225, closing ×2, largest piece, holes filled; scale from taurus-tx22-magazine-22.axis_height = 6.183 in (y-extent 1058 px → 171.1 px/in); origin at x min, y max of the outline; Douglas-Peucker at 0.004 in with the extremes kept: 146 points (IoU 0.999 with the full outline) (tools/trace.py)","via":"harvest","note":"The section square across the body: the body (above), the sleeve and the base plate (below). Its right edge carries a strip of each piece's side (the picture is turned): the model mirrors the left half about the faces' middle."}},"gaps":[{"what":"Every size of it: no page gives one (the 16-round's scale carries over, and with it the 16-round's doubt: the pistol's photographed pad is 8% longer than the 16-round's own at this scale)","need":"Taurus's figures, or a review that measures it"},{"what":"Its sleeve's top against the grip's bottom face: drawn on the 16-round's pad's top line; the square view of the magazine alone has it 0.02 in lower at the sleeve's rear end (1.9 degrees against 1)","need":"A square side view of it seated in the pistol"},{"what":"Its weight: worked out from the model's polymer (its insides assumed); a catalog's 3.4 oz stands beside it","need":"Taurus's figure or a review's weighing"}]},"taurus-tx22-thread-protector":{"id":"taurus-tx22-thread-protector","name":"TX22 Thread Protector","manufacturer":"Taurus","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/handguns/taurus-tx22-gen-2-toro-22-long-rifle-46in-hard-anodized-black-pistol-221-rounds/p/1883977","category":"muzzle_device","description":"The cap the T.O.R.O. comes with on its 1/2-28 muzzle thread: round at its front, rounded over at its front edge, wrench flats behind, a hole in its face. No page names it or sells it alone; it is on the pistol in every photo of the T.O.R.O. (\"Threaded Yes Thread Pitch 1/2 x 28\", Sportsman's Warehouse).","weight":"taurus-tx22-thread-protector.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"thread":{"origin":[0,0,0],"note":"Device frame: on the bore axis at the barrel's shoulder, +x toward the muzzle."},"front":{"origin":["{.length}",0,0],"note":"The device's front face: where the build's overall length ends."}},"interfaces":{"thread":{"type":"muzzle_thread","role":"device","anchor":"thread","params":{"thread":"1/2-28"},"flips":false,"note":"The barrel's own 1/2-28 (Taurus shop: \"Thread Pitch: 1/2x28\"), which it ships on: a protector that ships on its barrel states no thread length (the template's checklist)."}},"materials":{"body":{"label":"Thread protector","finish":"nitride","recolorable":false,"color":"steel-nitride-black","note":"A dark steel with a bright sheen in every photo (its silhouette reads grey 105 to 120 in the left view against the slide's 60 to 70, its rim a hard highlight in the right-front oblique): no page names its finish. Drawn as the catalog's polished black steel (`nitride`), whose look is the light in it."}},"components":{},"geometry":{"model":"taurus-tx22-thread-protector.glb","components":{},"approximations":["Turned at its silhouette's diameter (0.59 in, the three side views), from the barrel's shoulder to its front face where the pistol's published 7.60 in puts it (0.527 long): a round front 0.17 long, its edge rounded over at the left view's radius, and six wrench flats behind it (the left-front oblique), across them an assumed 0.53, leaving the round's corners standing (the silhouette is the round's all along in all three views).","Its front wall (0.06, assumed) has a hole in it (0.25, read on the right-front oblique); behind the wall it is threaded to take the barrel's thread: the barrel's helix, a drawing's gap outward (0.004, not a fit), turning with it when seated on the shoulder, out of its rear face.","Not drawn: a chamfer at its rear face, the flats' run-out into the round."],"ledger":["taurus-tx22-thread-protector.length","taurus-tx22-thread-protector.od","taurus-tx22-thread-protector.front_wall","taurus-tx22-barrel-46.thread_major_d","taurus-tx22-barrel-46.thread_minor_d","taurus-tx22-barrel-46.thread_pitch"]},"profiles":{},"gaps":[{"what":"Its flats (how many, how wide) and its front wall","need":"The protector off the barrel, stood on end and from the side (a seller's photo of Taurus's replacement protector)"}]},"taurus-tx22-toro-slide":{"id":"taurus-tx22-toro-slide","name":"TX22 T.O.R.O. Slide","manufacturer":"Taurus","url":"https://shoptaurus.com/new-items/taurustx-22-toro-conversion-kit","category":"slide","description":"The T.O.R.O.'s optics-ready slide: hard-anodized aluminium, a white-dot front sight and a drift-adjustable square-notch rear sight, three vents ahead of the ejection port, front and rear serrations, and an optic cut for the Shield RMSc footprint under a stepped cover plate held by two screws. Taurus sells it with its 4.6 in threaded barrel as the T.O.R.O. conversion kit for the newer TX22 frames (\"only compatible with the newer Taurus TX22 models (1-2TX22141 and 1-2TX22P141)\").","weight":"taurus-tx22-toro-slide.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"frame":{"origin":[0,0,0],"note":"The slide's rear face at the bore's height, on the bore axis: where the frame says a closed slide's rear face stands (taurus-tx22-frame.slide_rear_x, bore_axis_y)."},"barrel":{"origin":["{.breech_x}",0,0],"note":"Where the barrel's breech face stands: the barrel's origin."},"deck":{"origin":["{.screw_x}","{.cut_floor}",0],"note":"The optic cut's floor, midway between the footprint's two screw holes (the cover plate's two screws, side by side across it), on the slide's middle plane."}},"interfaces":{"frame":{"type":"tx22.slide","role":"slide","anchor":"frame","params":{},"flips":false,"note":"Its lower edge on the frame's top along its sides, bottom_below_axis under its origin: the frame's own seam_y, so that the two touch there."},"barrel":{"type":"tx22.barrel","role":"slide","anchor":"barrel","params":{},"flips":false,"note":"The barrel comes off the frame with the slide (Taurus shop's picture of the conversion kit)."},"optic":{"type":"optic_footprint","role":"deck","anchor":"deck","params":{"pattern":"shield_rmsc"},"flips":false,"cover":"cover","note":"Taurus, of the T.O.R.O. kit: \"Optic Ready Platform – Uses the Shield RMSc footprint , compatible with many micro red-dot optics.\" and \"The TX22 T.O.R.O. platform supports optics using the Shield RMSc footprint\"; Sportsman's Warehouse: \"the new TX22 T.O.R.O. uses the popular Shield RMSC optics footprint\". Against them, American Rifleman's review of the TX22 Black T.O.R.O.: \"the slide arrives with a cutout sized for the direct mounting of Holosun K-pattern footprints. With an adapter plate, optics with Shield RMSc or J-Point footprints can be used as well.\" The maker's own sentence is taken; the review's is the conflict, kept here. The cover plate (`cover`) is in the cut until a red dot is screwed in in its place."}},"materials":{"body":{"label":"Slide","finish":"anodized","recolorable":false,"color":"placeholder-black","note":"Gun Tests: \"SLIDE MATERIAL Aluminum SLIDE FINISH Hard Anodized Black\"; Taurus shop: \"Slide Finish: Hard Anodized Black\" and \"hard anodized slide\". The one finish the T.O.R.O. 1-2TX22P141 is sold in. A black on sealed anodize isn't fitted to a photo: its finish type is its look (`anodized`). Not drawn: the \"TX\" mark on each side of the nose (white in the photos) and the slide's other marks."},"cover":{"label":"Optic cover plate","finish":"anodized","recolorable":false,"color":"placeholder-black","note":"The plate in the optic cut: black in the side views and both obliques, its stepped top lit grey where it catches the light (as the slide's top does). No page names its finish; drawn as the slide's."},"screws":{"label":"Cover plate screws","finish":"nitride","recolorable":false,"color":"steel-nitride-black","note":"Two Torx heads, black steel in the left-front oblique (d4f6e257c86f), a little brighter than the plate round them."},"front_sight":{"label":"Front sight","finish":"nitride","recolorable":false,"color":"steel-nitride-black","note":"\"White-dot front sight\" (Taurus shop); Taurus: \"FRONT SIGHT Fixed (white dot)\" (Gun Tests' table). A black post in every photo, its white dot on its rear face."},"front_dot":{"label":"Front sight's white dot","finish":"polymer","recolorable":false,"color":"taurus-white-dot","note":"The dot on the post's rear face, toward the eye (\"white dot front\": American Rifleman)."},"rear_sight":{"label":"Rear sight","finish":"nitride","recolorable":false,"color":"steel-nitride-black","note":"\"a serrated, drift-adjustable square-notch rear sight\" (American Rifleman); \"REAR SIGHT Drift Adjustable\" (Gun Tests). Black, plain (no dots) in the obliques."},"guide_rod":{"label":"Recoil spring guide rod head","finish":"steel","recolorable":false,"color":"stainless-natural","note":"The recoil spring's guide rod head in the slide's front lug: a bare, bright steel disc in both obliques (7c0111a45816, d4f6e257c86f). It comes with the slide in Taurus's kit (\"Includes all necessary upper assembly components for installation\")."}},"components":{},"geometry":{"components":{"body":"taurus-tx22-toro-slide.body.glb","cover":"taurus-tx22-toro-slide.cover.glb"},"approximations":["The slide's side outline is its left side's silhouette on the pistol (Sportsman's 1883977-2), framed by the frame's two cross pins: its rear face leaning back to its foot, the nose and the rear block at full height, the open middle section's left wall at its lit rim. Its section is that outline across its width (0.93 in, read through the thread protector's front face in the right-front oblique), its two top edges chamfered 0.07 at 45 degrees; the nose's wider bevel at its front corners (where the \"TX\" is) isn't drawn as its own facet.","The right wall in the middle section is cut down further, to the ejection port's lit rim in the right view, between the rear block's front and the nose's rear; the walls' thickness there (0.09) and the room round the barrel inside are assumed, so that the barrel and the slide share nothing.","The three vents (American Rifleman: \"three weight-reducing vents located between the muzzle and the ejection port\"): the left one traced on the left view, the right one on the right view, the top one placed along the nose's top by the left-front oblique; each opens into the room round the barrel.","The serrations: five grooves each side at the front and seven at the rear, where the left view has them (each groove's width, pitch and lean read there; the right side's taken as the left's mirror); their depth (0.035) is assumed. The optic cut runs across the slide's top, open at both sides, at the plate's ends and lower edge; its two screw holes go down from the floor, the plate's two screws seated in them.","The cover plate is its own component (`cover`): its side face as the left view has it (four ramps, each falling a little toward the rear and a step above the one behind it; a flat, the screws' pad and a block at its rear end) across the slide's width, its sides in the slide's chamfer above the cut's floor (the left-front oblique's band of its side is as wide as a leaning face shows; no view from the front or behind). Along each ramp's two sides a facet between that chamfer and the ramp's top, a hundredth or two deep at the ramp's front and five or six at its rear as the two right views have it (the lit wedges in every photo), taken as half as wide again as it is deep (turned further to the top than the chamfer: lit where the chamfer is grey in the level views; no view across gives it). The seam round it: its foot and its ends' side edges broken, and the cut's floor broken under it (2026-11-06). Its two screws side by side across it, where the near one's head shows as a bump on the left view and the oblique has the two apart.","The screws' pad on the plate is its side outline across the plate, with the screws' heads on it; in the photos it is a round pad about the near screw, its side curved down to the plate's (a dark, curved face in both right views), which isn't drawn as such.","The sights are their side profiles at assumed widths (front 0.14, rear 0.6, the rear's square notch 0.12), standing on the slide's top in shallow dovetail seats; the front sight's white dot on its rear face. The front lug under the nose is the kit photo's length (0.27), down to where the left view has its face, its lower end a half round about the guide rod's axis (the close right-front view), so as wide as that round; the guide rod's head in it at the oblique's place and size. On the pistol only its front 0.08 shows ahead of the frame's dust cover: the rest stands inside the dust cover's front, which the frame's model is the one to hollow.","Not drawn: the long lit line along each side's lower half, from under the front serrations down to the rear block's front (in both side views and both obliques: a step or an engraved line, which way it goes isn't read on any view on file); the rear sight's serrations on its rear face (\"serrated\", American Rifleman; no photo looks at it from behind); the rails' grooves inside the walls, the breech face, the extractor and the striker's channel (the rear block's underside is open between its walls for the frame's rails, as far up as assumed); the marks (\"TX\" on each side of the nose)."],"ledger":["taurus-tx22-toro-slide.length","taurus-tx22-toro-slide.height","taurus-tx22-toro-slide.bottom_below_axis","taurus-tx22-toro-slide.width","taurus-tx22-toro-slide.top_chamfer","taurus-tx22-toro-slide.breech_x","taurus-tx22-toro-slide.cut_floor","taurus-tx22-toro-slide.ramp1_bevel_rear","taurus-tx22-toro-slide.plate_edge_break"]},"profiles":{"side":{"plane":"xy","origin":"The slide's rear face at the bore's height: the pin frame shifted by the frame's slide_rear_x and bore_axis_y.","offset":{},"points":[[-0.049,-0.293],[6.925,-0.304],[6.929,0.426],[6.917,0.471],[6.876,0.512],[6.692,0.518],[4.364,0.515],[4.279,0.417],[4.26,0.379],[4.26,0.29],[4.184,0.17],[4.104,0.079],[4.016,0.022],[3.94,0.003],[3.13,0.004],[3.051,0.058],[3.013,0.127],[2.988,0.254],[2.988,0.374],[3.007,0.387],[3.02,0.444],[2.954,0.523],[2.536,0.523],[2.517,0.441],[0.834,0.443],[0.822,0.525],[0.126,0.532],[0.098,0.517],[0.072,0.403]],"features":{"front_sight":[[[6.692,0.515],[6.661,0.578],[6.623,0.604],[6.401,0.629],[6.351,0.604],[6.338,0.515]]],"rear_sight":[[[0.544,0.51],[0.493,0.693],[0.367,0.693],[0.303,0.51]]],"cover_plate":[[[2.504,0.438],[2.504,0.526],[2.479,0.539],[2.34,0.539],[2.1,0.521],[2.081,0.54],[1.992,0.537],[1.72,0.527],[1.701,0.54],[1.379,0.54],[1.322,0.553],[1.265,0.553],[1.17,0.541],[0.961,0.528],[0.942,0.544],[0.898,0.547],[0.847,0.522],[0.841,0.44]]],"cover_screws":[[[1.341,0.566],[1.214,0.566],[1.214,0.541],[1.341,0.54]],[[0.955,0.56],[0.879,0.56],[0.879,0.535],[0.955,0.535]]],"left_window":[[[5.439,0.232],[4.269,0.233],[4.218,0.202],[4.193,0.113],[4.205,0.018],[4.25,-0.039],[5.249,-0.04],[5.3,0.011]]],"front_lug":[[[6.919,-0.308],[6.843,-0.307],[6.842,-0.826],[6.918,-0.826]]],"front_serrations":[[[6.56,0.186],[6.434,0.186],[6.228,-0.155],[6.355,-0.155]],[[6.358,0.187],[6.231,0.187],[6.026,-0.155],[6.152,-0.155]],[[6.155,0.187],[6.029,0.187],[5.823,-0.154],[5.95,-0.155]],[[5.953,0.187],[5.826,0.187],[5.621,-0.154],[5.747,-0.154]],[[5.75,0.187],[5.624,0.187],[5.419,-0.154],[5.545,-0.154]]],"rear_serrations":[[[1.949,0.375],[1.81,0.375],[1.465,-0.238],[1.604,-0.238]],[[1.74,0.376],[1.601,0.376],[1.256,-0.237],[1.395,-0.238]],[[1.531,0.376],[1.392,0.376],[1.047,-0.237],[1.187,-0.237]],[[1.326,0.376],[1.187,0.376],[0.842,-0.237],[0.981,-0.237]],[[1.114,0.376],[0.975,0.376],[0.63,-0.237],[0.769,-0.237]],[[0.905,0.377],[0.766,0.377],[0.421,-0.236],[0.56,-0.237]],[[0.696,0.377],[0.557,0.377],[0.212,-0.236],[0.352,-0.236]]]},"scaleRefs":["taurus-tx22-frame.front_pin_x","taurus-tx22-frame.front_pin_y"],"inputs":{"taurus-tx22-frame.bore_axis_y":0.467,"taurus-tx22-frame.front_pin_x":1.355,"taurus-tx22-frame.front_pin_y":0.03,"taurus-tx22-frame.slide_rear_x":-2.75},"tolerance":0.012,"photo":"references/taurus-tx22-toro f0237849b397 (Sportsman's Warehouse 1883977-2: the T.O.R.O. from its left, the muzzle at the left, 1200 x 1200)","method":"luminance < 232, inside [72, 178, 1184, 346], 4 boxes excluded, 1 polygons excluded, closing ×1, largest piece, holes filled; frame from the reviewed holes rear_pin, front_pin (158.1 px/in, rms 0.000 in over 2 points); origin at the photo's frame, shifted by ({taurus-tx22-frame.slide_rear_x}, {taurus-tx22-frame.bore_axis_y}); Douglas-Peucker at 0.012 in with the extremes kept: 29 points (IoU 0.994 with the full outline); checks: −y_min in x [0.5, 2.5] 0.299 ± 0.010 in vs taurus-tx22-toro-slide.bottom_below_axis 0.302 ± 0.03 (provisional): agrees; features through the same placement (front_sight: the front sight's side profile, base on the slide's top; rear_sight: the rear sight's side profile, base on the slide's top; cover_plate: the cover plate's side face: its stepped top (column by column, the first grey under 225) over its lower edge, the dark line at the cut's floor; cover_screws: the two screw heads' bumps on the plate's top (centres); left_window: the left vent's opening, its lit rim's outer edge; front_lug: the front lug's face as it shows ahead of the frame's dust cover, below the seam (its length is read on the kit's photo); front_serrations: the five front grooves, each between its two dark walls (20 px apart at row 285, the next 32 px on), leaning 0.6 px back for each row down, rows 266 to 322; rear_serrations: the seven rear grooves, each 22 px wide ending at its dark rear wall (918 to 1116 at row 300, 33 px apart), leaning 0.56 px back for each row down, rows 239 to 336 (they stop over the slide's lower edge in the left view and the kit's photo)) (tools/trace.py)","via":"harvest","note":"The slide alone as it shows on its frame from the left, the frame below the seam (the frame's top along its side, taurus-tx22-frame.seam_y) left out: its top silhouette is its far top edge; its front and rear ends are its near face's. Over the optic cut the outline is the cut's floor (the plate's lower edge); in the middle section it is the left wall's lit rim, under the barrel's chamber block."}},"gaps":[{"what":"The slide's width and its section","need":"A photo of the pistol from straight ahead or straight behind (any seller's), or Taurus's own page's views, which refuse the reader: a page the user saves from their own browser (D59)"},{"what":"The optic cut's footprint (Shield RMSc by Taurus, Holosun K by American Rifleman) and its screw spacing","need":"A page that dimensions the T.O.R.O.'s cut, or the plate off the slide from above"}]},"toolcraft-556-bcg":{"id":"toolcraft-556-bcg","name":".223/5.56/300 BLK M16 Profile Bolt Carrier Group - Black Nitride","manufacturer":"Toolcraft","sku":"TOOAUTO-016","category":"bolt_carrier_group","description":"Toolcraft's complete M16-profile bolt carrier group in salt black nitride, as its sellers list it: an 8620 carrier and a 9310 bolt, magnetic particle inspected.","weight":"toolcraft-556-bcg.weight","cartridge":{"takes":["5.56 NATO",".223 Rem",".300 Blackout"],"stated":"Caliber: 5.56x45mm NATO/.223 Rem, .300 Blackout","source":"Sellers' words (Toolcraft has no page for it): https://ar15discounts.com/products/toolcraft-223-5-56-300blk-m16-profile-bolt-carrier-group-black-nitride/ (its Technical Specs; its table has \"Cartridge Compatibility .223/5.56 NATO/.300 BLK\"), the same line at https://dirtybirdusa.com/products/toolcraft-223-5-56-300-blk-m16-profile-bolt-carrier-group-black-nitride/, and \"Caliber: .223 / 5.56 / 300 Blackout\" at https://www.righttobear.com/toolcraft-black-nitride-mpi-m16-bcg-tooauto-016/, as cached: harvest.quote."},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"channel":{"origin":[0,0,0],"note":"The receiver's rear face on the bore axis, +x toward the muzzle: the carrier's rear face stands here in battery."}},"interfaces":{"carrier_channel":{"type":"ar15.carrier_channel","role":"carrier","anchor":"channel","params":{},"flips":false}},"materials":{"body":{"label":"Carrier group","finish":"nitride","recolorable":false,"color":"steel-nitride-black","sheen":"satin","note":"AR15Discounts: \"Finish: Salt Black Nitride\" (its table: \"Finish Nitride / Melonite\", \"Bolt Finish Nitride / Melonite\"; \"Cam Pin: 8620 Steel w/ Black Nitride Finish\"); Toolcraft's own site: \"Black Nitride is a process commonly referred to as SBN (Salt bath nitride) and QPQ (quench polish quench).\" This number is the black nitride one: Toolcraft's nickel boron, DLC and phosphate groups are other products under other numbers. The carrier, the key, the cam pin and the bolt are one slot: all one polished black in AR15Discounts' two photos (03b83d654a76, d3f115e6c8f3). A black, not fitted to a photo: what a photo reads on it is the studio's lights (data/colors/steel.yaml). Satin: the photos' highlights are narrow and bright. Not drawn: the firing pin (\"hard chrome finish\"), the extractor and its black insert."},"screws":{"label":"Key screws","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The key's two socket screws (AR15Discounts: \"properly staked Grade-8 screws\"): black like the key in its three-quarter view (d3f115e6c8f3). No page names their finish: a black, not matched."}},"components":{},"geometry":{"model":"toolcraft-556-bcg.glb","components":{},"approximations":["Its shape is the Army's drawings', not Toolcraft's own (Toolcraft publishes nothing for it: \"Our carriers ... are all manufactured to customer print and specifications\"): its sellers call it \"Full Auto M16 Profile Direct Impingement\" (AR15Discounts, Dirty Bird) and \"a popular choice for AR-15, M4 and M16 builds due to its mil-spec design\" (Right To Bear), so it is drawn as the M16 carrier (8448507), its key (8448506) and screws (8448508), the cam pin (8448502) and the bolt (8448510) at those drawings' nominal sizes. The sellers' photos show that carrier; nothing was measured from them.","Drawn as the Army's assembly drawing (8448501) has it and as its sellers photograph it, out of the rifle: the bolt forward in the carrier (unlocked) and the cam pin upright. In battery the bolt is turned 22 1/2° and stands .255 to .325 in further back in the carrier; the carrier's rear face is put at the receiver's rear face.","Not drawn: the bores inside the carrier ahead of the slot and the bolt behind the carrier's front face, the extractor (its claw stands in as an eighth lug) and the ejector, the firing pin and its retaining pin, the gas rings, the key's 22°30' relief and its staking, any marking, fillets and edge breaks beyond the two cut corners and a small bevel.","Assumed where the drawing wasn't resolved: each lower rail's lower flank is the plane through the axis that touches the groove beside it (the end view's 10° callout wasn't placed); the groove's centre is where it touches the rib's side on the 45° ray; the cam track's helix is straight between the table's 0° and 20° rows; the 1.500 R is the run-out of the two grooves to the rear, from 2.35 ahead of the tail's shoulder (first read as the bottom cut's own); the notch under the tail runs the tail's length; the serrations' steep faces are toward the front, as the makers' photos show them; the screws' heads are flush with the key's top (the counterbores' depth isn't dimensioned); the vents, the hole in the right side and the cam track are drawn in as far as the bolt's diameter."],"ledger":["toolcraft-556-bcg.length","toolcraft-556-bcg.od"]},"profiles":{},"gaps":[{"what":"Anything from Toolcraft itself","need":"Toolcraft's site has no page, number, weight or drawing for it: every figure is a seller's"},{"what":"A weight that was weighed","need":"11.408 oz is one seller's figure (a second page repeats it in the same text); no page says it was put on a scale"},{"what":"What the seller's \"7.7 × 1 × 1.4 in\" measures","need":"A seller's statement: the drawings' carrier with its bolt forward is 7.46 in long"}]},"unity-fast-micro-226":{"id":"unity-fast-micro-226","name":"FAST Micro Mount, 2.26 in optical centerline","manufacturer":"Unity Tactical","sku":"FST-MICB","url":"https://www.primaryarms.com/unity-tactical-fast-ap-micro-mount-black","category":"optic_mount","description":"Unity Tactical's riser for an Aimpoint Micro-footprint red dot: \"The optical centerline of the mount is a nominal 2.26” above the rail\" (the maker's launch text), \"about 1/3\" higher than other popular 1.93\" mounts\", for shooting in a gas mask or with ear protection on. Built into it are a \"standard 1.42” height, windage-adjustable back up rear iron sight as well as an optional elevation adjustable front sight\", 1.27 in apart. It clamps to the rail by \"a no-snag dual cross-bolt clamp\" and a rail-grabber bar (a QD lever from ADM can take the bar's place, sold separately). 7075-T6, Type III hardcoat anodized; 3.0 oz. unitytactical.com refuses the reader: the page linked is Primary Arms' for the black one.","weight":"unity-fast-micro-226.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":[0,0,0],"note":"Mount frame: on the rail's top midway between the two cross bolts, which are four slots apart (cross_bolt_spacing): the slot the build names is the one between them, two from each."},"deck":{"origin":["{.deck_x}","{.deck_above_rail}",0],"note":"On the deck's top at the recoil boss, the footprint's middle: where a Micro dot's base is put (D101)."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":"={.mount_length} / 2","clamp_front":"={.mount_length} / 2","cross_rear":"={.cross_bolt_spacing} / 2","cross_front":"={.cross_bolt_spacing} / 2"},"flips":false,"note":"The body's whole length clamps: two cross bolts four slots apart (Soldier Systems' print of the launch text: \"It securely attaches to Milspec M1913 Picatinny rail via a no-snag dual cross-bolt clamp or optional American Defense Mfg patented QD Auto Lock Lever\"; the instruction sheet: \"If using Standard Rail Grabber Mount clamp, install the mount on weapon. Secure screws using a T25 bit driver. Lightly snug all screws before applying final torque to any. TORQUE TO 35 IN-LBS.\"). Nothing the maker publishes says where on a rifle's rail it goes."},"deck":{"type":"optic_footprint","role":"deck","anchor":"deck","params":{"pattern":"aimpoint_micro"},"flips":false,"note":"Arisaka Defense (the maker's text): \"Designed for Aimpoint® Micro (H1, H2, T1, T2, CompM5) and other optics with Aimpoint® Micro footprint\" and \"NOTE: DOES NOT FIT AIMPOINT COMP M5S OR M5B.\"; Soldier Systems: \"Compatible with most optics that feature the ubiquitous Aimpoint Micro footprint\" (data/interfaces.yaml, optic_footprint)."}},"materials":{"body":{"label":"Mount","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Black","finish":"anodized_matte","color":"placeholder-black","sku":"FST-MICB","source":"https://www.primaryarms.com/unity-tactical-fast-ap-micro-mount-black"},"fde":{"label":"Flat Dark Earth","finish":"anodized_matte","color":"unity-fde","sku":"FST-MICF","source":"https://www.primaryarms.com/unity-tactical-fast-aimpoint-micro-mount-fde"}},"default":"black","note":"The mount's one block of 7075: \"Machined from 7075-T6 aluminum and Type III hardcoat anodized black\" / \"... anodized flat dark earth\" (Primary Arms' two pages); TNVC: \"Due to the chemical process that takes place during Type III Hardcoat Anodizing, color may vary from part to part\". In every photo of either it is a matte satin with no hard highlight, so `anodized_matte`; the black is the placeholder black (a black on anodize isn't fitted), the FDE a preset (unity-fde) fitted under the app's light to Primary Arms' photo of its left side; Rifle Supply's photos of the FDE are an olive khaki, as \"FDE varies\". Also sold, and not offered here: Clear (\"Color Choose an option Black FDE Clear\": TNVC; Big Tex: \"Black Anodized FDE Anodized Clear\"), with no number and no photo of it on file; and OD Green (Custom Night Vision: \"Color FDE, Black, OD Green\"), with no number and no photo of it on file. Not drawn: the white engraving (UNITY, PAT. PEND., CAGE 81C38, the star, the R and U arrows)."},"hardware":{"label":"Bolts, drum and grabber","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","note":"Black on both colours of the mount (the FDE photos: 52f6e3ffa50f, 21330942adc2, 132598ee129a): the two cross bolts' Torx heads, the rear sight's windage drum on the right and the rail-grabber bar on the left with the bolts' ends in it; inside, the rear aperture ring and the front post. No page names what they are made of or how finished; in the photos the heads and the drum are a satin black like the bar's, so all are drawn in the one matte black."}},"components":{"body":{"label":"Mount","material":"body"},"hardware":{"label":"Bolts","material":"hardware"}},"geometry":{"model":"unity-fast-micro-226.glb","components":{},"approximations":["The deck's height is the maker's 2.26 in less an Aimpoint T-2's axis over its base (no page names the dot the 2.26 was given for): the maker's own graphic, scaled by its 2.01 in, has it 0.10 in higher (the ledger keeps both). The jaws' feet are where the published 2.01 in puts them under that deck.","The body is the right side's outline (traced on Primary Arms' square photo of the black one) across a section read on TNVC's end photo: the deck 0.91 in wide, its edges a chamfer down to the walls 0.85 in across, and on the right under the band's step the bolts' band out to 0.654 in. The left face is the right's mirror without its drum, holes and band (the photos of the left side are obliques; there the rail-grabber bar takes the band's place).","Nothing is drawn above the deck's plane where a dot's base stands. The deck is drawn as the obliques show it: two rims along its edges at the deck's plane (a dot's base stands on them; their width read by eye), the channel between them sunk 0.05 in (assumed), the recoil boss in its middle left flush with the rims where it rises into the dot's base, and a round-ended opening either side of the boss down into the sight tunnel (their sizes read by eye on an oblique). The four screw holes up through the deck and the threaded holes in the rims aren't cut: the Aimpoint Micro footprint's pattern isn't on file.","The sight tunnel (the oval window through each side, the upper window through each end) and the big window (through each side, and the lower window through each end) are cut through as the side photo and the end photo read them, their corners rounded at the radius read on the big window's; the end windows' rounded corners are a quarter of their width. The pockets in each side are cut 0.025 in deep (assumed), the rear one with its lower front edge on a line a web's width off the big window's slope.","The rear sight is drawn as its windage drum in its round relief on the right face (its slot not drawn) and an aperture ring in the sight tunnel at the maker's 1.42 in, on the drum's axis along the rifle; the ring's length and its peep hole's size are assumed. The front post is a plain pin at the sight radius ahead of it, from the lower end window's roof up through the tunnel's floor to 1.42 in, its diameter assumed; its threaded body and the hex in its foot aren't drawn.","The cross bolts are their heads flush in counterbores on the band, each with its Torx socket as a twelve-point star; their shanks across the rail aren't drawn, and their ends in the grabber bar are flush discs each ringed by a groove (sizes ratios of the heads'). The grabber bar is a block from the deck's left wall out to the clamp's width, its ends cut back at 45 degrees on the outer face, its length along the rail assumed (1.9 in), its jaw the rail's own head (MIL-STD-1913's section), as the right jaw's is. The windage drum's screwdriver slot is drawn straight (it is waisted), and the screw's end shows as a pin on the left face on the drum's axis. The octagonal recess between the bolts (for the QD lever's nut) and its round hole through, and the two small threaded holes beside it, are cut into the band. Every machined edge of the body is broken by the 0.011 in read on the side photo.","The engraving and the logo aren't drawn."],"ledger":["unity-fast-micro-226.deck_above_rail","unity-fast-micro-226.deck_x","unity-fast-micro-226.mount_length","unity-fast-micro-226.overall_height","unity-fast-micro-226.width"]},"profiles":{"side":{"plane":"xy","origin":"the middle of the mount's length (the middle between its two cross bolts, 0.001 in off it in the FDE photo) on the deck's top; the app raises it by deck_above_rail","offset":{"y":"deck_above_rail"},"points":[[-1.035,-0.252],[-1.027,-1.865],[-0.995,-1.933],[-0.942,-1.987],[-0.9,-2.012],[-0.87,-2.02],[-0.714,-2.02],[0.884,-2.014],[0.95,-1.977],[1.024,-1.889],[1.035,-1.827],[1.035,-1.695],[1.024,-0.86],[1.028,-0.072],[1.022,-0.042],[0.997,-0.016],[0.948,0],[0.31,0],[0,-0.002],[-0.973,-0.005],[-1.012,-0.027],[-1.033,-0.052]],"scaleRefs":["unity-fast-micro-226.mount_length","unity-fast-micro-226.overall_height"],"inputs":{"unity-fast-micro-226.mount_length":2.08,"unity-fast-micro-226.overall_height":2.01},"tolerance":0.006,"photo":"references/unity-fast-micro-226 bbcff7c94073 (Primary Arms FST-MICB_03: the black mount's right side, square on from a hair above, on white)","method":"luminance < 200, closing ×2, largest piece, holes filled; scale from unity-fast-micro-226.mount_length = 2.08 in (x-extent 1301 px → 625.5 px/in) and unity-fast-micro-226.overall_height = 2.01 in (y-extent 1270 px → 631.8 px/in), which agree within 1.0%; mean 628.7 px/in; origin at x center, y max of the outline; Douglas-Peucker at 0.006 in with the extremes kept: 22 points (IoU 0.997 with the full outline) (tools/trace.py)","via":"harvest","note":"The mount's right side, its windows filled: the deck's top, the square ends with their small chamfers, and the bolts' band down to the jaws' feet with its corners cut. The top row is a sliver of the deck seen from a hair above (the photo's height reads 1% over the published 2.01 at its length's scale)."}},"gaps":[{"what":"The deck's height, measured","need":"a review that measures the deck or the axis of a named dot on it, or Unity's own drawing with the deck dimensioned: the maker's graphic, scaled by its own 2.26 in and by its 2.01 in, puts the deck 1.71 and 1.775 in over the rail; the T-2's figures put it at 1.671 (adopted)"},{"what":"Which dot the 2.26 in is for","need":"the maker's page (unitytactical.com refuses the reader) or a seller quoting it with a dot named"},{"what":"A square view of the left side, from above and from below","need":"the rail-grabber bar's length and shape and the deck's plan (its rims, boss, recess and screw holes) are read on obliques and the instruction sheet's drawings only"},{"what":"The Clear and the OD Green","need":"a seller's page with the colour's number and a photo of it"},{"what":"The maker's own shop","need":"unitytactical.com refuses the reader; sellers on file carry it"}]},"vg6-gamma-556":{"id":"vg6-gamma-556","name":"GAMMA 556","manufacturer":"VG6 Precision","sku":"APVG200001A","url":"https://www.aeroprecisionusa.com/vg6-gamma-556","category":"muzzle_device","description":"VG6 Precision's brake and compensator in one, now made and sold by Aero Precision under APVG200001A (Primary Arms calls it the GEN 2): two chambers, each with a large port through both sides and narrow slots under it, a slot over the top from the front face back over both chambers with three small holes either side, a three-lobed exit, and a rear section with wrench flats, two grooves and one hole on top. 17-4 PH stainless steel in black nitride, timed with the crush washer it comes with. Not a suppressor mount. The first generation, APVG100001A (no top slot, rows of round holes beside its side ports, a taper to the rear section; 1.75 in and 2.1 oz by Midwest Gun Works' page), is the older product, and not this one. Aero: \"optimized to efficiently utilize gas from the muzzle on 10.5-18.5” barrel lengths\", and it \"virtually eliminates recoil and muzzle movement during firing\": the maker's claim, with no figure behind it on file (LoadoutRoom's review, of a Gamma on a .300 Blackout: \"no scientific testing was needed\").","weight":"vg6-gamma-556.weight","cartridge":{"takes":["5.56 NATO",".223 Rem"],"stated":"For 5.56mm / .223 Rem","source":"https://www.primaryarms.com/vg6-precision-gamma-5-56-high-performance-muzzle-brake-1-2x28-gen-2 (its Features list, as cached 2026-10-28: harvest.quote). Aero's page: \"Platform AR15\"; Wing Tactical: \"Caliber: .223 Rem. / 5.56 NATO / .224 Valkyrie\"."},"occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"thread":{"origin":[0,0,0],"note":"Device frame: on the bore axis at the barrel's shoulder, +x toward the muzzle. The crush washer bears on the shoulder, the device's rear face on the washer."},"front":{"origin":["{.length}",0,0],"note":"The device's front face: where the build's overall length ends."}},"interfaces":{"thread":{"type":"muzzle_thread","role":"device","anchor":"thread","params":{"thread":"1/2-28"},"flips":false,"note":"Primary Arms: \"1/2x28 RH\", \"Thread Pattern 1/2 X 28\"; Rifle Supply and Aerospace Arms: \"Thread: 1/2-28 RH\"; Wing Tactical: \"Any .223 Rem. / 5.56 NATO caliber barrel with 1/2\\\"-28 thread pitch\". Timed with its crush washer: \"Includes crush washer\" (Primary Arms). No page gives how long a barrel thread it takes: no thread_length."}},"materials":{"body":{"label":"Brake","finish":"nitride","recolorable":false,"color":"steel-nitride-black","note":"One colourway sold under this number: Aero's page, \"Finish Black Nitride\"; Primary Arms, \"17-4ph heat treated stainless steel\", \"Black nitride satin finish\", \"68RC surface hardness\"; Rifle Supply and Aerospace Arms, \"Finish: BLACKNITRIDE™ - Satin Finish(Half Gloss)\". Wing Tactical's page names a second finish beside its two numbers (\"MPN: APVG200001A / APVG200010A\", \"Finish: Blacknitride or Bead Blasted Stainless\") and has a photo of a bare one beside a black (046693be26b5); no page on file sells the stainless one by its number, so it isn't offered. A nitride is drawn by its finish type, not fitted to a photo (data/colors/steel.yaml). The logo and \"GAMMA 556\" lasered on top aren't drawn."},"washer":{"label":"Crush washer","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The crush washer in the box (\"Includes crush washer\", Primary Arms; \"1x Crush Washer\", Wing Tactical). No page names its finish; a dull black in Primary Arms' three photos of it, a little greyer than the brake. A black, not matched."}},"components":{"body":{"label":"Brake","material":"body"},"washer":{"label":"Crush washer","material":"washer"}},"geometry":{"model":"vg6-gamma-556.glb","components":{},"approximations":["Every size along the device is read on photos of APVG200001A scaled by its adopted length (1.83 in, Wing Tactical's), and every size across it by the 0.86 in diameter four sellers state; the maker's own four gallery pictures and Primary Arms' standing photo agree with that length to 0.01 in. Where a reading is an assumption for the drawing (the threaded bore's depth, the top slot's floor, the exit's lobes, the rear hole's depth), the ledger says so.","Turned: one diameter from the front face to the rear one, a 45-degree chamfer at each face, and two square grooves on the rear section (the front one shallower than the flats, so the flats run through it). Then cut: two wrench flats on the rear section's sides from the rear face to the rear port, the two side ports straight through from side to side (rounded rectangles in the side view, square to the axis), the top slot from the front face back past the web with a round end, three small holes either side of it, four narrow slots under the front chamber and two under the rear, each through the wall toward the axis, the bore through the web and the front face, three lobes round the exit, a hole on top of the rear section, and the thread.","The ports, slots and holes are cut square to the surface they open in. Whether any is drilled at a slant, and the chambers' shape inside beyond what the through-cut ports open, isn't sourced; the side ports are cut straight through, which is what the backdrop seen through them in every side view shows.","The three small holes either side of the slot are drilled toward the axis at the angles their places seen from above give on the head's round (39 and 30 degrees off the top); the narrow slots underneath likewise (18 and 39 degrees off the bottom under the front chamber, 29 under the rear).","The exit's three lobes are wedges round the bore at 120 degrees, one straight up into the top slot's end, reaching 0.2 in from the axis and running 0.12 in back: an assumption from an oblique photo (Primary Arms' APVG200001A_00), as the ledger says.","The thread is the 1/2-28 cut as a helix, 0.6 in deep (assumed: no view shows it), the bore beyond it.","The crush washer is drawn as a plain ring at its free thickness as read in a photo (0.105 in): a crush washer is flattened some way as the device is timed, by an amount no source states. Its conical face isn't drawn.","The lasered logo and lettering aren't drawn."],"ledger":["vg6-gamma-556.overall_length","vg6-gamma-556.washer_thickness","vg6-gamma-556.length","vg6-gamma-556.od","vg6-gamma-556.flats_across","vg6-gamma-556.front_port_height","vg6-gamma-556.rear_port_height","vg6-gamma-556.slot_width","vg6-gamma-556.bore_d"]},"profiles":{"plan":{"plane":"xz","origin":"the device's rear face, on the bore axis (the crush washer puts it washer_thickness ahead of the barrel's shoulder)","offset":{},"points":[[0,0],[0,-0.124],[0.005,-0.326],[0.007,-0.362],[0.015,-0.375],[0.218,-0.375],[0.238,-0.369],[0.238,-0.352],[0.244,-0.346],[0.349,-0.349],[0.356,-0.344],[0.364,-0.371],[0.375,-0.375],[0.596,-0.372],[0.606,-0.365],[0.62,-0.375],[0.763,-0.375],[0.805,-0.337],[0.853,-0.313],[0.898,-0.306],[0.989,-0.306],[1.07,-0.311],[1.124,-0.339],[1.159,-0.376],[1.169,-0.427],[1.265,-0.427],[1.273,-0.419],[1.278,-0.393],[1.296,-0.375],[1.329,-0.353],[1.372,-0.337],[1.415,-0.33],[1.512,-0.33],[1.553,-0.337],[1.603,-0.363],[1.628,-0.39],[1.632,-0.426],[1.638,-0.429],[1.807,-0.427],[1.823,-0.416],[1.827,-0.402],[1.832,-0.145],[1.825,-0.131],[1.823,-0.052],[1.825,0.105],[1.832,0.128],[1.832,0.278],[1.827,0.409],[1.817,0.427],[1.636,0.429],[1.628,0.383],[1.581,0.349],[1.536,0.33],[1.481,0.327],[1.384,0.33],[1.334,0.349],[1.273,0.4],[1.273,0.421],[1.265,0.429],[1.167,0.429],[1.161,0.378],[1.147,0.35],[1.096,0.315],[1.055,0.303],[0.879,0.306],[0.822,0.33],[0.767,0.375],[0.755,0.363],[0.365,0.363],[0.356,0.344],[0.349,0.351],[0.253,0.351],[0.244,0.363],[0.011,0.363],[0.005,0.328]],"scaleRefs":["vg6-gamma-556.overall_length","vg6-gamma-556.od"],"inputs":{"vg6-gamma-556.od":0.86,"vg6-gamma-556.overall_length":1.83},"tolerance":0.004,"photo":"references/vg6-gamma-556 a935992d9bfd (Resilient Arms' picture of APVG200001A from above, muzzle up, the slot to the lens, 450 x 820)","method":"luminance < 200, inside [0, 0, 450, 820], closing ×2, largest piece, holes filled; rotated -90.0° as declared; scale from vg6-gamma-556.overall_length = 1.83 in (x-extent 770 px → 420.8 px/in) and vg6-gamma-556.od = 0.86 in (y-extent 361 px → 419.8 px/in), which agree within 0.2%; mean 420.3 px/in; origin at x min, y center of the outline; Douglas-Peucker at 0.004 in with the extremes kept: 75 points (IoU 0.996 with the full outline); checks: height in x [0.03, 0.2] 0.738 ± 0.007 in vs vg6-gamma-556.flats_across 0.738 ± 0.012 (provisional): agrees; height in x [0.29, 0.34] 0.700 ± 0.007 in vs vg6-gamma-556.groove_2_d 0.703 ± 0.012 (provisional): agrees; height in x [1.65, 1.78] 0.857 ± 0.007 in vs vg6-gamma-556.od 0.86 ± 0 (corroborated): agrees (tools/trace.py)","via":"harvest","note":"From above: the rear section reads narrower than the head by its flats, and the side ports show as notches either side, the rear one deeper (it is the taller port). The top slot and the holes are inside the outline."},"side":{"plane":"xy","origin":"the device's rear face; the middle of the outline's height, the bore axis","offset":{},"points":[[0,0.339],[0,0.003],[0,-0.327],[0.006,-0.399],[0.025,-0.424],[0.228,-0.424],[0.242,-0.41],[0.237,-0.361],[0.25,-0.347],[0.35,-0.341],[0.363,-0.355],[0.369,-0.405],[0.383,-0.424],[0.465,-0.429],[0.498,-0.385],[0.603,-0.38],[0.622,-0.394],[0.622,-0.416],[0.647,-0.429],[1.803,-0.429],[1.827,-0.405],[1.833,-0.289],[1.833,0.289],[1.827,0.388],[1.808,0.407],[1.214,0.407],[1.104,0.429],[0.625,0.424],[0.622,0.399],[0.603,0.38],[0.493,0.385],[0.465,0.429],[0.377,0.424],[0.363,0.372],[0.344,0.347],[0.25,0.347],[0.237,0.361],[0.242,0.41],[0.223,0.429],[0.019,0.424],[0.006,0.405]],"scaleRefs":["vg6-gamma-556.overall_length","vg6-gamma-556.od"],"inputs":{"vg6-gamma-556.od":0.86,"vg6-gamma-556.overall_length":1.83},"tolerance":0.006,"photo":"references/vg6-gamma-556 9a99cc0f47f2 (Aero's own picture of APVG200001A's left side, square on, muzzle up, its top at the right edge, 1000 x 630)","method":"luminance < 200, inside [380, 230, 620, 600], closing ×2, largest piece, holes filled; rotated -90.0° as declared; scale from vg6-gamma-556.overall_length = 1.83 in (x-extent 333 px → 182.0 px/in) and vg6-gamma-556.od = 0.86 in (y-extent 156 px → 181.4 px/in), which agree within 0.3%; mean 181.7 px/in; origin at x min, y center of the outline; Douglas-Peucker at 0.006 in with the extremes kept: 41 points (IoU 0.993 with the full outline); checks: height in x [0.03, 0.2] 0.848 ± 0.017 in vs vg6-gamma-556.od 0.86 ± 0 (corroborated): agrees; height in x [0.52, 0.59] 0.771 ± 0.017 in vs vg6-gamma-556.groove_1_d 0.786 ± 0.012 (provisional): agrees; height in x [0.29, 0.34] 0.694 ± 0.017 in vs vg6-gamma-556.groove_2_d 0.703 ± 0.012 (provisional): agrees (tools/trace.py)","via":"harvest","note":"The left side: mirrored, then turned a quarter to put the muzzle at the right and the top up, as the right side would be seen. One diameter end to end but for the two grooves; the side ports are holes in the silhouette, filled. 333 px long: a pixel is 0.0055 in. Its length over its width is 2.18, 2.3% over the published 1.83 and 0.86 (the scales' spread, inside agree)."}},"gaps":[{"what":"A maker's figure for the second generation's length, diameter and weight","need":"VG6's or Aero's own specification or drawing for APVG200001A (Aero's page leaves \"Weight(s)\" blank; vg6precision.com's page is gone): until then the length is one seller's figure that the photos bear out, and three other sellers print the first generation's 1.75 in"},{"what":"The inside: how deep the thread goes, the chambers' shape, the slot's floor, the exit's lobes","need":"a photo straight into the front face and one into the rear, or a section (VG6's patents, if a marking page ties one to this product)"},{"what":"The stainless colourway (APVG200010A)","need":"a page that sells it by its own number, with a photo of it"}]},"vltor-a5-buffer-spring":{"id":"vltor-a5-buffer-spring","name":"A5 Action Spring","manufacturer":"VLTOR","sku":"V2-1174-C102","url":"https://vltor.com/products/v2-1174-c102","category":"buffer_spring","description":"The A5 system's spring: a standard rifle action spring, held in the A5's tube round the A5 buffer. VLTOR: \"Rifle-Length action spring for the A5 system.\" \"This is the stock spring utilized in the Vltor A5 buffer systems. This rifle spring has the proper specs, including length, coil count, and wire diameter.\" On the A5 page: \"A standard rifle action spring — not a carbine spring. More coils, more controlled compression, smoother return.\" \"The extra coils provide a smoother, more linear compression curve\". Its kits call it the \"A5 Buffer Spring\".","weight":"vltor-a5-buffer-spring.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[{"slot":"receiver_extension","parts":["vltor-a5-receiver-extension"],"says":"VLTOR, of its A5 spring and buffer kit: \"The SP-A5 kit is designed for the VLTOR A5 system and is only compatible with other VLTOR A5 products. The SP-A5 spring kit requires the use of an A5 receiver extension tube. The physical dimensions of A5 buffer components are different than that of standard carbine or rifle buffer components. You cannot blend components from the different buffer systems.\"","source":"https://www.vltor.com/products/sp-a5"}],"anchors":{"bore":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the receiver extension's axis where a buffer's front face rests, +x rearward: the spring is drawn as installed, from the buffer's seat to the tube's rear wall."}},"interfaces":{"bore":{"type":"ar15.extension_bore","role":"buffer","anchor":"bore","params":{},"flips":false,"note":"VLTOR: \"You cannot run a carbine spring in an A5 tube.\" and \"A standard carbine spring won't work because it doesn't provide enough return force in the longer tube.\" (https://vltor.com/a5). Held by `requires`."}},"materials":{"spring":{"label":"Spring","finish":"stainless","recolorable":false,"color":"stainless-natural","note":"A bright grey wire in VLTOR's photograph of the spring sold alone (15385186c4e5), drawn as bright metal (not fitted to a photo: the app's natural steel). VLTOR names no material or finish; the Army's drawing of the rifle's spring has stainless wire (type 631, 17-7 PH, heat treated: std.carbine_action_spring's note on BCM's). VLTOR's two kit pictures (2531fc1da290, ba600a518974) show it a bronze brown, the colour that steel takes in heat treatment and that BCM's spring is drawn in: one picture of the spring in both, a composite with the buffer and the tube's own photographs. Sold in the one finish (the one SKU)."}},"components":{},"geometry":{"model":"vltor-a5-buffer-spring.glb","components":{},"approximations":["Drawn as it is in a rifle: held between the A5H2's head and the rear wall inside the RE-A5, 7.66 in long, where it is 12.5 in free. Its wire (.072), its outside diameter (.940) and its 44 coils are the Army's drawing's of the rifle's action spring, which VLTOR says it is; VLTOR's photograph of it counts 41 and 42 crests and reads 12.46 in.","Its end coils are closed; the one coil at each end that the Army's drawing reduces to .900 isn't drawn reduced.","The wire's section is a polygon of the round wire's area (lib.coil_x)."],"ledger":["vltor-a5-buffer-spring.wire_d","vltor-a5-buffer-spring.od","vltor-a5-buffer-spring.end_coil_od","vltor-a5-buffer-spring.coils","vltor-a5-buffer-spring.free_length","vltor-a5-buffer-spring.installed_length"]},"profiles":{},"gaps":[{"what":"Its weight","need":"VLTOR's figure or a scale: 2.23 oz is worked out from its wire's length and steel's density"},{"what":"Its free length, wire and diameter as VLTOR makes it","need":"VLTOR's figures: they are the Army's drawing's of the rifle's spring, which VLTOR says it is"}]},"vltor-a5-receiver-extension":{"id":"vltor-a5-receiver-extension","name":"RE-A5 7-Position Receiver Extension, MilSpec Diameter","manufacturer":"VLTOR","sku":"RE-A5","url":"https://vltor.com/products/re-a5","category":"receiver_extension","description":"VLTOR's A5 receiver extension: a mil-spec diameter tube 11/16 in longer than a carbine one, with seven stock positions, for the A5 buffer and the rifle-length spring. VLTOR: \"The RE-A5 Receiver Extension is a 7-position receiver extension tube designed to work with the VLTOR A5 Buffer System. This receiver extension is slightly longer than the traditional M4 receiver extension and is designed to work with Mil-Spec dimensioned M4/AR-15 type collapsible stocks.\" \"Seven position receiver extension made from impact extruded 7075 T6 aluminum\", \"Type III Hard coat anodized black\", \"Dry Film Lube applied to interior surface\", \"Adjustment positions are numbered and are visible through the witness hole on most stocks\". Sold alone and in VLTOR's A5 Buffer Kit (SKU \"RE-A5 and SP-A5\": the tube, the A5H2 buffer, the A5 buffer spring, VLTOR's lockplate and castle nut).","weight":"vltor-a5-receiver-extension.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[{"slot":"buffer","parts":["vltor-a5h2-buffer"],"says":"VLTOR, of this tube: \"The RE-A5 is not compatible with standard carbine buffers or carbine springs. Using a carbine buffer in the A5 tube will cause the shorter buffer to over-travel, which can result in firearm damage. Always use A5-specific buffers and a rifle-length spring.\"","source":"https://vltor.com/a5"},{"slot":"buffer_spring","parts":["vltor-a5-buffer-spring","bcm-rifle-m16-action-spring"],"says":"VLTOR: \"The A5 system uses a rifle-length spring, not a carbine spring. ... You cannot run a carbine spring in an A5 tube.\" and \"The RE-A5 is not compatible with standard carbine buffers or carbine springs.\"","source":"https://vltor.com/a5"}],"anchors":{"receiver_thread":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the tube axis at the takedown pin's X, +x rearward."},"tube":{"origin":[0,0,0],"x":[1,0,0]},"end":{"origin":["0in - {std.ar15.receiver_rear_x}",0,0],"x":[1,0,0],"note":"On the tube axis at the receiver's rear face (the Army's drawing of the lower), where an end plate bears."},"bore":{"origin":["0in - {std.ar15.upper_rear_face_x}",0,0],"x":[1,0,0],"note":"On the tube axis where a buffer's front face rests with the bolt forward: against the carrier's rear end, which stands at the upper receiver's rear face (the Army's drawings). The A5 buffer and the rifle-length spring are placed from it."}},"interfaces":{"receiver_thread":{"type":"ar15.buffer_tube_mount","role":"tube","anchor":"receiver_thread","params":{},"flips":false,"note":"VLTOR: \"Thread 1-3/16 x 16 (mil-spec)\" (https://vltor.com/a5)."},"tube":{"type":"receiver_extension","role":"tube","anchor":"tube","params":{"profile":"mil-spec","od":"={.tube_od}","positions":7,"step":"={.position_step}"},"flips":false,"note":"VLTOR: \"MilSpec Diameter\" (its name); \"Positions 7\" (its product page); \"7-position mil-spec receiver extension ... It accepts any standard mil-spec collapsible stock\"; \"Position Spacing 0.650\"\" (https://vltor.com/a5). A stock made for a carbine tube's six positions has seven places on this one; whether it collapses to the first isn't said by VLTOR for any stock."},"extension_end":{"type":"ar15.extension_end","role":"tube","anchor":"end","params":{},"flips":false},"bore":{"type":"ar15.extension_bore","role":"tube","anchor":"bore","params":{},"flips":false,"note":"The A5's bore: VLTOR, \"The RE-A5 is not compatible with standard carbine buffers or carbine springs. Using a carbine buffer in the A5 tube will cause the shorter buffer to over-travel, which can result in firearm damage. Always use A5-specific buffers and a rifle-length spring.\" (https://vltor.com/a5). Held by `requires`."}},"materials":{"tube":{"label":"Receiver extension","finish":"anodized","recolorable":false,"color":"placeholder-black","note":"One piece of 7075 aluminium, hard anodized black: VLTOR, \"Finish Type III Hard coat anodized black\" (its product page) and \"Type III Hard coat anodized black\", \"made from impact extruded 7075 T6 aluminum\". VLTOR sells the RE-A5 in black only (the one SKU, RE-A5). A black on sealed anodize isn't fitted to a photo: the anodized finish's black. VLTOR's three photographs of it (ffe8eb512fc6, 4b0990a26750, 20475bac1645) show a satin dark grey under a hard light, the numbers 1 to 7 and VLTOR's marks lasered white; the marks aren't drawn."}},"components":{},"geometry":{"model":"vltor-a5-receiver-extension.glb","components":{},"approximations":["The tube is the standard's outside (1.148, VLTOR's \"MilSpec Diameter\"), VLTOR's length (7 15/16), its front face where the Army's drawings put a mil-spec tube's, and its thread the standard's 1 3/16-16 (a helix between the Army drawing's limits) as long as VLTOR's photographs have it (1.10 in to its last crest), with a relief behind it at the thread's root to the shoulder the photographs show (1.51 in). Bored to the drawing's inch to a rear wall of the carbine tube's 0.072 with its 0.094 hole: no page gives the A5's bore length, and the wall is assumed.","The rail under it is the standard's width and depth (Magpul's drawing of the mil-spec tube), with VLTOR's own front: a low lip under the tube from the relief's shoulder (0.04 in deep, read on a photograph that has the rail turned toward the lens), then a ramp from 2.33 in behind the front face to full depth at 2.80 (about 32°, where the mil-spec tube's is 45° and ends at 2.59).","Along the rail's underside a channel with rounded ends, from 4.64 in to 0.35 in ahead of the rear face (read on VLTOR's photograph), its width and depth assumed (0.25, 0.08): no view on file shows the underside square on. The seven holes, 0.30 in across, are in its floor at VLTOR's 0.650 in, the rear one 0.63 in ahead of the rear face (read on the holes' rims and on the engraved 7); each is wider than the channel and stands out of its sides, as VLTOR's photograph has them.","The rear face's outer edge and the rail's rear end are rounded off (assumed 0.04 in): VLTOR's photograph of the rear end shows a small round all round it.","Not drawn: the slot under the thread at six o'clock (no photograph shows the RE-A5's mouth from below), the plain lip at the mouth ahead of the thread's first crest, the fillets where the rail meets the tube (20475bac1645 has them, small), and VLTOR's marks: the numbers 1 to 7 down the left side, \"VLTOR PAT PEND RE - A5\" on the lip, and the V on the rear face."],"ledger":["vltor-a5-receiver-extension.tube_od","vltor-a5-receiver-extension.tube_length","vltor-a5-receiver-extension.tube_front_behind_pin","vltor-a5-receiver-extension.position_step","vltor-a5-receiver-extension.position_hole_d","vltor-a5-receiver-extension.position_hole_rear_from_rear","vltor-a5-receiver-extension.channel_rear_from_rear","vltor-a5-receiver-extension.channel_front_from_rear","vltor-a5-receiver-extension.channel_width","vltor-a5-receiver-extension.channel_depth","vltor-a5-receiver-extension.rail_ramp_start","vltor-a5-receiver-extension.rail_ramp_end","vltor-a5-receiver-extension.rail_lip_depth","vltor-a5-receiver-extension.relief_end","vltor-a5-receiver-extension.thread_length","vltor-a5-receiver-extension.rear_wall","vltor-a5-receiver-extension.rear_edge_round"]},"profiles":{},"gaps":[{"what":"The bore's length and the rear wall's thickness","need":"VLTOR's figure, a drawing, or a section of the tube: the model has the carbine tube's 0.072 wall"},{"what":"The position holes' size and exact places, and the channel's width and depth","need":"a photograph of the rail's underside square on with a known size in frame"},{"what":"A slot or notch at the mouth for the buffer retainer (the mil-spec tube's key slot)","need":"a photograph of the mouth from below; none on file shows it"}]},"vltor-a5h2-buffer":{"id":"vltor-a5h2-buffer","name":"A5H2 Buffer, 5.3 oz.","manufacturer":"VLTOR","sku":"A5H2","url":"https://vltor.com/products/a5h2","category":"buffer","description":"The A5 system's standard buffer, longer than a carbine buffer and only for VLTOR's A5 receiver extension. VLTOR: \"The default A5 Buffer at 5.3 oz and the recommended starting point for most standard builds.\" \"Internal Weights 2 Steel, 2 Tungsten\", \"Design Cascading Deadblow\"; on the A5 page \"Material Aluminum\". \"NOTE: A5 buffers are only compatible with other VLTOR A5 buffer system components. The buffers themselves are longer than traditional carbine buffers, and they cannot be used in standard carbine receiver extensions. The A5 Buffer is not compatible with the AR-10 Platform.\" Its head is marked \"A5-2 VLTOR US. PAT. 8296984\".","weight":"vltor-a5h2-buffer.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[{"slot":"receiver_extension","parts":["vltor-a5-receiver-extension"],"says":"VLTOR, of the A5H2: \"NOTE: A5 buffers are only compatible with other VLTOR A5 buffer system components. The buffers themselves are longer than traditional carbine buffers, and they cannot be used in standard carbine receiver extensions.\"","source":"https://vltor.com/products/a5h2"},{"slot":"buffer_spring","parts":["vltor-a5-buffer-spring"],"says":"VLTOR: \"The A5 buffer requires a longer receiver extension and rifle-length spring to function. A standard carbine tube is too short — the buffer will over-travel and damage your lower receiver. Don't mix and match.\"","source":"https://vltor.com/a5"}],"anchors":{"bore":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the buffer's axis at its head's front face, +x rearward (toward its bumper)."}},"interfaces":{"bore":{"type":"ar15.extension_bore","role":"buffer","anchor":"bore","params":{},"flips":false,"note":"VLTOR: \"A5 buffers are only compatible with other VLTOR A5 buffer system components ... they cannot be used in standard carbine receiver extensions.\" Held by `requires`."}},"materials":{"body":{"label":"Buffer body","finish":"anodized_matte","recolorable":false,"color":"vltor-a5-buffer-bronze","note":"Aluminium (VLTOR's A5 page: \"Material Aluminum\"), a bronze anodize in every photograph of it on file: VLTOR's close view of its head (references/vltor-a5h2-buffer 7dfeb8e9eab3), its kit pictures (references/vltor-a5-buffer-spring 2531fc1da290, ba600a518974) and its picture of the A5 buffer in its card (746290c9afa4). VLTOR names no finish and sells the A5H2 in the one colour (the one SKU, A5H2)."},"bumper":{"label":"Bumper","finish":"polymer","recolorable":false,"color":"vltor-a5-buffer-bumper","note":"A translucent milky white in VLTOR's pictures (2531fc1da290, 746290c9afa4), its end tapered as the standard bumper's is; VLTOR names no material. Drawn opaque under `polymer`, as BCM's and Guntec's bumpers are."},"pin":{"label":"Pin","finish":"steel","recolorable":false,"color":"steel-phosphate-dark","note":"The pin through the body and the bumper: a small dark round head in a hole near the bumper in VLTOR's kit picture (2531fc1da290). Its finish isn't stated or read."}},"components":{},"geometry":{"model":"vltor-a5h2-buffer.glb","components":{},"approximations":["The standard carbine buffer's pattern (lib.carbine_buffer: the Army's drawings of the buffer's head, bumper and pin, the reference model's carbine body), with the A5H2's own length (3.70 in, read on VLTOR's picture of it by its own diameters) and its pin 0.19 in from the body's open end: VLTOR's picture has the head, the step behind it and the body in the standard's proportions, and the bumper standing the standard's 0.4 in out. The body is what is longer than a carbine buffer's.","The head's flats are the standard's three, a third of a turn apart: VLTOR's close view of the head (7dfeb8e9eab3) shows two flats a third of a turn apart and the face round where it is turned away from the lens; the third isn't seen.","Not drawn: the four weights inside it (VLTOR: \"Internal Weights 2 Steel, 2 Tungsten\", \"Cascading Deadblow\"), which are what the A5H0 to A5H4 change; the mark on its head (\"A5-2 VLTOR US. PAT. 8296984\"); the head's front edge as round as the close view has it."],"ledger":["vltor-a5h2-buffer.length","vltor-a5h2-buffer.od","vltor-a5h2-buffer.body_length","vltor-a5h2-buffer.pin_from_open_end"]},"profiles":{},"gaps":[{"what":"Its length","need":"VLTOR's figure, or a photograph of the A5H2 square from the side with a known size in its plane: the photograph read is a kit picture looking a little down on it, and VLTOR's comparison table (its A5 buffer three quarters of an inch longer than a carbine buffer of 3.25) says 4.0"},{"what":"The number of flats on its head","need":"a view of its head face on"}]},"vltor-castle-nut":{"id":"vltor-castle-nut","name":"Receiver Extension Lock Nut","manufacturer":"VLTOR","sku":"V2-1069-M3","url":"https://vltor.com/products/v2-1069-m3","category":"castle_nut","description":"The nut on the receiver extension's thread that is turned down onto the end plate and locks the extension to the lower receiver, its four notches taking the wrench. VLTOR: \"Mil-Spec Receiver Extension Lock Nut (Castle Nut)\" (sold alone, V2-1069-M3). Its A5 kits list it as \"(1) Vltor Castle Nut\" (\"(1) RE-A5 Receiver Extension (1) A5H2 Buffer (1) A5 Buffer Spring (1) Vltor Lockplate (1) Vltor Castle Nut\").","weight":"vltor-castle-nut.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"seat":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the tube axis at the nut's front face, which bears on the end plate, +x rearward."}},"interfaces":{"nut_seat":{"type":"ar15.end_plate_seat","role":"nut","anchor":"seat","params":{},"flips":false,"note":"It goes on the RE-A5's mil-spec thread (VLTOR: \"Thread 1-3/16 x 16 (mil-spec)\", https://vltor.com/a5)."}},"materials":{"nut":{"label":"Castle nut","finish":"phosphate","recolorable":false,"color":"steel-phosphate-black","note":"A black with a little sheen in VLTOR's photograph of it (references/vltor-castle-nut a899784bf2cd) and its kit pictures (2531fc1da290, ba600a518974); VLTOR names neither its material nor its finish. Drawn as a black phosphate on steel, as a mil-spec nut is made."}},"components":{},"geometry":{"model":"vltor-castle-nut.glb","components":{},"approximations":["Its outside is the mil-spec nut's as the AR-15 CAD reference set draws it (1.363 in; VLTOR sells it as \"Mil-Spec Receiver Extension Lock Nut\"): neither of VLTOR's two pictures of it has a size of its own, and its thickness (0.334, on the kit picture) and notches (0.12 wide on both, 0.11 deep on its own photograph) are read on them as fractions of that.","A ring bored to the extension's thread's crests (std.receiver_extension.thread_major_d), as BCM's and Guntec's nuts are drawn: its own thread, which the picture shows inside it, isn't drawn, nor the bore's chamfers.","Its four wrench notches are cut square-floored, 90 degrees apart (counted on the kit picture, 92, 94, 85 and 89 degrees apart, and on VLTOR's photograph of the nut alone), one at the top, since how a nut is turned on its thread isn't fixed.","What its front face has (a mil-spec nut has three staking notches in its outer edge) isn't drawn: no view on file shows the nut's front face."],"ledger":["vltor-castle-nut.od","vltor-castle-nut.thickness","vltor-castle-nut.notches","vltor-castle-nut.notch_width","vltor-castle-nut.notch_depth"]},"profiles":{},"gaps":[{"what":"Its sizes","need":"VLTOR's figures, or a photograph of the nut with a known size in its plane: its outside is the mil-spec nut's and the rest is read as fractions of it on two 1024 px pictures"},{"what":"Its front face","need":"A photograph of the nut's front face: whether it has staking notches"}]},"vltor-lockplate":{"id":"vltor-lockplate","name":"Receiver Extension End Plate","manufacturer":"VLTOR","sku":"V2-1069-M1","url":"https://vltor.com/products/v2-1069-m1","category":"end_plate","description":"The plate between the castle nut and the lower receiver: a ring round the receiver extension with a lobe that covers the takedown pin's detent spring, a key in its hole that rides in the extension's slot, a boss on its front face and the dimple behind it, VLTOR's V in the dimple. VLTOR: \"Mil-Spec Receiver Extension End Plate\" (sold alone, V2-1069-M1). Its A5 kits list it as \"(1) Vltor Lockplate\" (\"(1) RE-A5 Receiver Extension (1) A5H2 Buffer (1) A5 Buffer Spring (1) Vltor Lockplate (1) Vltor Castle Nut\"); the SP-A5's short description calls it the \"End Plate\".","weight":"vltor-lockplate.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"end":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the tube axis at the plate's front face, which bears on the receiver's rear face, +x rearward."},"nut_seat":{"origin":["{.thickness}",0,0],"x":[1,0,0],"note":"The plate's rear face, where the castle nut bears."}},"interfaces":{"extension_end":{"type":"ar15.extension_end","role":"fitting","anchor":"end","params":{},"flips":false},"nut_seat":{"type":"ar15.end_plate_seat","role":"plate","anchor":"nut_seat","params":{},"flips":false}},"materials":{"plate":{"label":"End plate","finish":"phosphate","recolorable":false,"color":"steel-phosphate-black","note":"A matte black in VLTOR's photograph of it (references/vltor-lockplate dd62a391c0ba) and its kit pictures (2531fc1da290, ba600a518974); VLTOR names neither its material nor its finish. Drawn as a black phosphate on steel, as the mil-spec plate is made; the V in its dimple is bronze in the pictures (a filled or lasered mark) and isn't drawn."}},"components":{},"geometry":{"model":"vltor-lockplate.glb","components":{},"approximations":["The mil-spec end plate as the AR-15 CAD reference set draws it (its outline, hole, key, the V either side of the key, the boss and the dimple), which VLTOR's photograph of the plate sold alone, square on and scaled by its hole, reads within 0.015 in (its ring 1.378 across for 1.363, its top 0.683 for 0.682, its bottom 1.391 for 1.379, its dimple 0.49 by 0.40 for 0.506 by 0.385): VLTOR sells it as \"Mil-Spec Receiver Extension End Plate\".","Its thickness and the boss's and dimple's depths are the mil-spec plate's on the reference model: no view on file shows its edge or its front face.","Not drawn: VLTOR's V in the dimple (bronze in the photographs: a filled or lasered mark)."],"ledger":["vltor-lockplate.thickness","vltor-lockplate.height","vltor-lockplate.top_above_axis","vltor-lockplate.bottom_below_axis","vltor-lockplate.lobe_radius","vltor-lockplate.lobe_centre_below_axis","vltor-lockplate.boss_width","vltor-lockplate.boss_height","vltor-lockplate.boss_below_axis"]},"profiles":{},"gaps":[{"what":"Its thickness, its front face and its material","need":"VLTOR's figures, or a photograph of the plate's edge and front face: every size is the mil-spec plate's, read against VLTOR's two photographs"}]},"vortex-sport-cantilever-30mm-mount":{"id":"vortex-sport-cantilever-30mm-mount","name":"Sport Cantilever 30mm Mount","manufacturer":"Vortex","sku":"SCM-30-150","url":"https://vortexoptics.com/sport-cantilever-mount-scm-30-150.html","category":"scope_mount","description":"Vortex's one-piece cantilever scope mount for a 30 mm tube, the rings' axis 1.50 in above the rail (\"Center Scope Height 1.50\"\"), \"Lightweight, under 5.5 oz.\" in \"6061 Aluminum\". The rings are \"Horizontally split for easier mounting\"; two clamp blocks, each on two screws, hold it to a Picatinny rail, and two recoil lugs under it lie in the rail's slots. Vortex: \"The 2\" offset gets your head position and eye relief dialed, while leaving plenty of real estate on your rail.\"","weight":"vortex-sport-cantilever-30mm-mount.weight","occupies":[],"integral":[],"brings":[],"seats":{},"requires":[],"anchors":{"rail_clamp":{"origin":[0,0,0],"note":"Mount frame: on the rail's top over the rear recoil lug's middle, +x forward. The mount has no cross bolt: its rear lug lies in the slot the build names, its front lug in the next slot ahead, and its jaws reach 1.34 in behind that slot and 1.81 ahead of it."},"rings":{"origin":["({.ring_rear_x} + {.ring_front_x}) / 2","{.optical_axis_above_rail}",0],"note":"On the rings' axis midway between the two rings: where a scope's saddle is put at position 0."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{"clamp_rear":"={.clamp_rear_reach}","clamp_front":"={.clamp_front_reach}","cross_front":"={.lug_spacing}"},"flips":false,"note":"Two fixed jaws on the right and two clamp blocks on the left, each block on two Torx T-25 screws (\"Base Screw Torque 30 in-lbs.\") that cross the mount above the rail's top; two recoil lugs in two neighbouring slots. It is clamped from 1.34 in behind the rear lug's slot to 1.81 in ahead of it, 3.15 in of rail, and its front ring stands ahead of that: Vortex pictures it at the front of the receiver's rail with the front ring over the handguard (Sportsman's Warehouse: \"With a 2in offset, this mount positions your scope forward\")."},"rings":{"type":"scope_rings","role":"rings","anchor":"rings","params":{"diameter":"={.ring_bore}","rear_ring":"=({.ring_rear_x} - {.ring_front_x}) / 2","front_ring":"=({.ring_front_x} - {.ring_rear_x}) / 2","ring_length":"={.ring_length}"},"flips":false,"note":"Two rings bored 30 mm (\"Tube Size 30mm\"; the base's rear end is engraved \"30MM 1.50\"\"), 3.43 in apart middle to middle and 0.735 long each: 2.69 in between their faces for a scope's saddle. Four cap screws to a ring, Torx T-25 (\"Cap Screw Torque 15-18 in-lbs.\"; the caps are engraved \"18 in-lbs\")."}},"materials":{"body":{"label":"Mount","finish":"anodized_matte","recolorable":false,"color":"placeholder-black","options":{"black":{"label":"Matte black","finish":"anodized_matte","color":"placeholder-black","sku":"SCM-30-150","source":"https://vortexoptics.com/sport-cantilever-mount-scm-30-150.html"}},"default":"black","note":"One colourway, under one number: Vortex's page lists \"Type 2 Low-Glare Matte Black Anodized\" and no other finish (Primary Arms: \"Color Black\", \"Finish Matte\"; Sportsman's: \"Finish Matte Black\"). A matte anodize, `anodized_matte`, in the catalog's black: a black on anodize isn't fitted to a picture. Piece by piece on Vortex's own four pictures (2026-10-13; they read as renders): the two rings (caps and lower halves), the stems, the arm, the base with its fixed jaws and lugs, and the two clamp blocks are all the one matte black; the twelve screws are not (the `hardware` slot). The white engraving (\"18 in-lbs\" on each cap, \"30MM 1.50\"\" and \"30 in-lbs\" on the base's rear end) and the maker's mark on each side aren't drawn."},"hardware":{"label":"Screws","finish":"steel","recolorable":false,"color":"placeholder-black","note":"The twelve Torx screws, eight in the ring caps and four in the clamp blocks: in Vortex's pictures their heads are a blacker, glossier black than the matte mount round them, with a sheen on the socket's lobes. What they are made of and coated with isn't said on a page read (the page calls them \"T-25 Torx® Screws\"): drawn as dark steel, the placeholder black (a black on steel isn't fitted to a photo)."}},"components":{"body":{"label":"Mount","material":"body"},"hardware":{"label":"Screws","material":"hardware"}},"geometry":{"model":"vortex-sport-cantilever-30mm-mount.glb","components":{},"approximations":["No view of the mount is square across, and only one is square along it: Vortex's picture of it on a rifle with a scope in it, the rifle's right side, where the mount is 328 px long. Its lengths are read there by the rail's slots (a pixel is 0.016 in); its widths through cameras fitted to the two bores in two three-quarter pictures. In that side view the scope and the mount read 1.7 to 1.9% small up and down by the rail's scale: the rings stand at the published 1.50 in, and the outline below them is as traced.","The arm and the rises either side of the rear ring are the side outline between the arm's two walls, which are not about the mount's middle: 0.11 in left and 0.22 right of it (0.32 across), read through both cameras as its top flat's two edges and a chamfer off each (2026-10-19); along its top from the rear ring's stem to the front ring's each edge is chamfered, the left 0.075 in across and the right 0.025, each at 45 degrees (the angle assumed: each side is seen in one picture, whose camera gives a line of widths and drops). The base between the clamp blocks, under the rear ring's stem, is drawn as wide as the recoil lugs where they leave it (0.27 each side, both sides alike), from the rail's top to the base's top; under each ring the same outline leans in from the ring's foot (0.81 in) to what is under it at the base's top. Where the walls with the maker's mark end along the mount isn't read: they are drawn between the two blocks. The model's metal comes to 4.54 oz of aluminium and 0.19 oz of screw heads for a mount of 5.39 oz with its twelve screws, whose shanks aren't drawn (about half an ounce of steel).","Each ring is its measured section along its length: a top flat, two chamfers, a short side flat above and below the split, two long chamfers down to the stem. The two screw pockets a side are round cuts straight down into the cap's chamfer; under each the screw's hole runs on down and breaks out of the lower chamfer, which is the small window that shows the thread in the pictures (the thread itself isn't drawn). The rings are bored to the tube they are for, closed on it, the split a groove 0.014 in wide; its depth, 0.02, is assumed.","The twelve screws are their heads only: a head half as tall as it is across with a six-pointed socket three fifths of its width (ratios, not readings), the socket 0.02 deep (assumed), eight upright in the caps' pockets and four in the clamp blocks' counterbores, a hundredth under the blocks' faces (assumed). Every machined edge is broken by 0.006 in (assumed: the figure the other mounts on file are drawn with).","The side outline steps a pixel of its picture at a time (0.016 in) along the arm's straight lift and its flat top: it is simplified again at that pixel before anything is built from it, so those edges are drawn straight.","The base is a block as wide as the base at each end of the clamp, each with its fixed jaw on the right, and the outline's middle between them; the left-hand clamp blocks are separate pieces, their underside drawn as one flat face from the outer face's lower edge in to the hook's foot, which is taken to be as low as the fixed jaws'. Under all four the rail's place is the rail's own head in section (MIL-STD-1913's) from the rail's top down to the lower gauge line, and plain walls below that.","The two recoil lugs are drawn as bars in the rail's slot 0.27 in each side of the middle, where their right-hand ends read where they leave the base, as deep as a slot (the standard's 0.118 in: their depth isn't read); the left-rear picture shows lugs in the same notch on the left, drawn alike, and whether each is one bar or two short ones no picture shows.","Not drawn: the white engraving and the maker's mark on each side; the rounds where the rear ring's stem runs into the base and the arm (they are the side outline's corners only)."],"ledger":["vortex-sport-cantilever-30mm-mount.optical_axis_above_rail","vortex-sport-cantilever-30mm-mount.ring_bore","vortex-sport-cantilever-30mm-mount.ring_rear_x","vortex-sport-cantilever-30mm-mount.ring_front_x","vortex-sport-cantilever-30mm-mount.ring_length","vortex-sport-cantilever-30mm-mount.ring_width","vortex-sport-cantilever-30mm-mount.ring_top_above_axis","vortex-sport-cantilever-30mm-mount.stem_width","vortex-sport-cantilever-30mm-mount.arm_width","vortex-sport-cantilever-30mm-mount.mount_length","vortex-sport-cantilever-30mm-mount.clamp_rear_reach","vortex-sport-cantilever-30mm-mount.clamp_front_reach","vortex-sport-cantilever-30mm-mount.base_right_z","vortex-sport-cantilever-30mm-mount.clamp_outer_z"]},"profiles":{"side":{"plane":"xy","origin":"on the rail's top over the rear recoil lug's middle (the receiver's slot the lug lies in), +x toward the muzzle: the frame is five of the receiver's slot centres on the line of the rail's top, counted from that slot","offset":{},"points":[[-1.343,0.026],[-1.334,0.018],[2.361,0.002],[2.41,0.035],[2.492,0.051],[2.541,0.083],[2.622,0.099],[2.671,0.131],[2.753,0.147],[2.802,0.179],[2.932,0.211],[2.981,0.244],[3.014,0.244],[3.063,0.276],[3.193,0.308],[3.242,0.34],[3.291,0.34],[3.307,0.356],[3.698,0.355],[3.714,0.371],[3.763,0.371],[3.779,0.387],[3.812,0.387],[3.861,0.419],[3.894,0.419],[3.959,0.451],[4,0.508],[4.001,0.834],[3.993,0.842],[3.244,0.845],[3.236,0.804],[3.179,0.748],[3.146,0.748],[3.015,0.683],[2.934,0.667],[2.885,0.635],[2.804,0.619],[2.755,0.587],[2.673,0.571],[2.624,0.538],[2.543,0.522],[2.494,0.49],[2.412,0.474],[2.363,0.442],[2.282,0.426],[2.216,0.394],[1.24,0.398],[1.223,0.382],[0.979,0.383],[0.963,0.399],[0.898,0.399],[0.881,0.416],[0.849,0.416],[0.67,0.514],[0.638,0.514],[0.597,0.555],[0.565,0.621],[0.558,0.857],[-0.159,0.86],[-0.168,0.607],[-0.201,0.575],[-0.201,0.559],[-0.258,0.518],[-0.454,0.421],[-0.486,0.422],[-0.519,0.389],[-0.551,0.389],[-0.666,0.325],[-1.333,0.328]],"scaleRefs":["std.picatinny.slot_pitch"],"inputs":{"std.picatinny.slot_pitch":0.394},"tolerance":0.008,"photo":"references/vortex-sport-cantilever-30mm-mount 910667d8ac8f (Vortex ..._30mm_mp_w.jpg: the mount on a rifle with a scope in it, the rifle's right side square on; what shows between the rail's top and the tube's underside)","method":"luminance < 200, inside [750, 365, 1092, 417], largest piece, holes filled; frame from the reviewed holes s-7, s-4, s-1, s2, s5 (61.4 px/in, rms 0.001 in over 5 points); origin at the photo's frame; Douglas-Peucker at 0.008 in with the extremes kept: 69 points (IoU 0.992 with the full outline); The outline is cut a hair under the tube (row 365) and along the rail's top (row 417): its upper edge inside each ring and its lower edge under the base are those cuts, not edges of the mount. (tools/trace.py)","via":"harvest","note":"The mount's side between the rail and the tube: the base's top behind the rear ring, the rise to the rear ring's stem, the arm's top and its lift to the front ring, the front ring's foot. At the rail's scale; the same picture's heights read 1.7% under the published centre height."}},"gaps":[{"what":"A length, a ring spacing or a width from Vortex","need":"none is published on its page or at any seller read; its parts diagram and instruction card are on a host whose robots.txt disallows the reader (vortexoptics.widen.net) and were left alone"},{"what":"A view of the mount alone square on from the side, from above, from an end, or of its underside","need":"none exists in the maker's gallery or any seller's (they all show the maker's four): a seller's or an owner's own photo with a rail or a ruler in it"},{"what":"The arm's chamfers' angle, and how far the walls with the maker's mark run along the base","need":"a view of the arm from its end or from below (each side is seen in one picture, which gives a line of widths and drops: drawn at 45 degrees); the walls are drawn between the two clamp blocks"},{"what":"What Vortex's \"2\\\" Offset\" spans","need":"a sentence or a drawing from Vortex; on the side view no span of the mount comes to 2 in within its ±"},{"what":"Black matched under the app's light (it is the optics' placeholder)","need":"a black on matte anodize isn't fitted to a picture (D81)"}]}},"interfaces":{"ar15.upper_lower":{"label":"AR-15 receiver pins","description":"Takedown and pivot pin axes joining upper and lower. Anchor origin at the takedown pin axis center, x toward the pivot pin.","roles":{"lower":"upper","upper":"lower"},"compat":[{"param":"pin_spacing","rule":"within","tolerance":"0.005in","optional":false,"message":"Pin spacing differs"}],"beside":[]},"ar15.buffer_tube_mount":{"label":"AR-15 receiver extension thread","description":"Buffer tube threads, coaxial with the bore line. Anchor origin on the axis at the takedown pin's X, x pointing rearward.","roles":{"receiver":"tube","tube":"receiver"},"compat":[],"beside":[]},"receiver_extension":{"label":"Receiver extension (buffer tube)","description":"Stock rides on the tube. Anchor origin on the tube axis; x rearward. Index = stock position (1 = collapsed).","roles":{"tube":"stock","stock":"tube"},"index":{"param":"position","pitch":"step","on":"tube","direction":1,"min":1,"maxParam":"positions"},"compat":[{"param":"profile","rule":"equal","optional":false,"message":"Mil-spec and commercial tubes differ in OD; the stock will not fit"}],"beside":[]},"ar15.barrel_extension":{"label":"Barrel extension","description":"The barrel's extension in the upper receiver's bore, held by the barrel nut. Anchor at the receiver's front face on the bore axis, x toward the muzzle.","roles":{"receiver":"barrel","barrel":"receiver"},"compat":[],"beside":[]},"ar15.handguard_mount":{"label":"Handguard mount","description":"Where a handguard fixes to the upper (a barrel nut, or a proprietary nut). Anchor at the receiver's front face on the bore axis, x toward the muzzle.","roles":{"receiver":"handguard","handguard":"receiver"},"compat":[{"param":"nut","rule":"equal","optional":false,"message":"The handguard mounts by a different barrel nut from the one the upper receiver takes"}],"beside":[]},"ar15.delta_ring":{"label":"Delta ring on the barrel nut","description":"The delta ring's seat on the barrel nut, against the receiver's front face. Anchor at the receiver's front face on the bore axis, x toward the muzzle.","roles":{"nut":"ring","ring":"nut"},"compat":[],"beside":[]},"ar15.drop_in":{"label":"Drop-in handguard's hold","description":"No anchor: the delta ring and the cap that hold a drop-in handguard, and the handguard, say by it that they go together.","roles":{"ring":"handguard","nut":"handguard","cap":"handguard","handguard":"ring"},"compat":[{"param":"shape","rule":"among","role":"cap","optional":true,"message":"The handguard's front doesn't take a cap of this shape"}],"beside":["gas_block"]},"ar15.handguard_cap":{"label":"Handguard cap seat","description":"Where a drop-in handguard's front cap bears on the front sight base: the base's rear face. Anchor on the bore axis at that face, x toward the muzzle.","roles":{"block":"cap","cap":"block"},"compat":[{"param":"journal_od","rule":"equal","optional":false,"message":"The cap is bored for a different journal from the one the front sight base sits on"}],"beside":[]},"ar15.handguard_front":{"label":"Drop-in handguard's front in its cap","description":"The inside of a handguard cap's face, and the end of a drop-in handguard's front flange that goes in to it. Anchor on the bore axis, x toward the muzzle.","roles":{"cap":"handguard","handguard":"cap"},"compat":[],"beside":[]},"ar15.front_sight_post":{"label":"Front sight post seat","description":"The front sight base's threaded hole the post screws into. Anchor on the post's axis at the top of the tower, x toward the muzzle, y up.","roles":{"base":"post","post":"base"},"compat":[],"beside":[]},"ar15.gas_journal":{"label":"Gas block journal","description":"The barrel's gas block seat (its journal diameter and the gas port's place). Anchor at the gas port on the bore axis, x toward the muzzle.","roles":{"barrel":"block","block":"barrel"},"compat":[{"param":"journal_od","rule":"equal","optional":false,"message":"The gas block is bored for a different journal from the one the barrel has"}],"beside":[]},"ar15.gas_tube":{"label":"Gas tube","description":"The tube from the gas block back to the carrier key. Anchor at the block's tube hole, x rearward.","roles":{"block":"tube","tube":"block"},"compat":[],"beside":[]},"ar15.gas_system":{"label":"Gas system length","description":"The length of gas system a barrel's port is placed for, and a gas tube is made to: carbine, mid, rifle. No anchor: nothing is placed by it.","roles":{"barrel":"tube","tube":"barrel","handguard":"barrel"},"compat":[{"param":"length","rule":"equal","optional":false,"message":"The gas tube is made for another length of gas system than the barrel's: it wouldn't reach from the gas block to the carrier's key, or would run past it"}],"beside":[]},"ar15.carrier_channel":{"label":"Bolt carrier channel","description":"The upper receiver's bore that the bolt carrier group rides in. Anchor at the receiver's rear face on the bore axis, x toward the muzzle.","roles":{"receiver":"carrier","carrier":"receiver"},"compat":[],"beside":[]},"ar15.charging_handle_channel":{"label":"Charging handle channel","description":"The upper receiver's channel the charging handle rides in. Anchor where the handle stops, on the channel's axis, x toward the muzzle: on the receiver the front wall of the open notch under its rail's rear end (its handle_seat_x), on the handle its T's shoulder.","roles":{"receiver":"handle","handle":"receiver"},"compat":[],"beside":[]},"ar15.extension_end":{"label":"Receiver extension end","description":"The receiver extension's threaded end at the receiver: the end plate sits there, against the receiver's rear face. Anchor on the tube axis at the receiver's rear face, x rearward.","roles":{"tube":"fitting","fitting":"tube"},"compat":[],"beside":[]},"ar15.end_plate_seat":{"label":"End plate, where the castle nut bears","description":"An end plate's rear face: the castle nut is turned down onto it (2026-10-12, D82: until then the nut was placed from the receiver, by one plate's thickness). Anchor on the tube axis at that face, x rearward.","roles":{"plate":"nut","nut":"plate"},"compat":[],"beside":[]},"ar15.extension_bore":{"label":"Receiver extension bore","description":"Inside the receiver extension: the buffer and its spring. Anchor on the tube axis where a buffer's front face rests with the bolt forward (against the carrier's rear end, at the upper receiver's rear face), x rearward: a buffer's own frame begins at its front face, and a spring is drawn from the buffer's seat to the tube's rear wall.","roles":{"tube":"buffer","buffer":"tube"},"compat":[],"beside":[]},"ar15.grip_lug":{"label":"AR-15 grip mount","description":"Grip screw boss under the lower, behind the trigger guard.","roles":{"receiver":"grip","grip":"receiver"},"compat":[],"beside":[]},"ar15.trigger_guard":{"label":"AR-15 trigger guard ears","description":"Trigger guard pin/roll-pin ears at the front and the grip interface at the rear.","roles":{"receiver":"guard","guard":"receiver"},"compat":[],"beside":[]},"ar15.fcg":{"label":"AR-15 fire-control group (mounting only)","description":"Trigger and hammer pin axes. Mounting interface only; no pocket geometry is modeled.","roles":{"receiver":"trigger","trigger":"receiver"},"compat":[{"param":"pin_diameter","rule":"equal","optional":false,"message":"Small-pin and large-pin FCGs are not interchangeable"}],"beside":[]},"ar15.selector":{"label":"AR-15 safety selector","description":"The selector's hole through the lower receiver, above the grip. Anchor on the hole's axis at the receiver's mid-plane, x toward the muzzle; a selector's own anchor is the middle of the length of shaft that lies in the receiver.","roles":{"receiver":"selector","selector":"receiver"},"compat":[],"beside":[]},"ar15.lpk":{"label":"AR-15 lower parts kit","description":"External controls (selector, bolt catch, magazine release, pin heads) at their standard locations.","roles":{"receiver":"kit","kit":"receiver"},"compat":[],"beside":[]},"ar15.magwell":{"label":"AR-15 magazine well","description":"Anchor where a seated magazine's frame origin sits (the rear face of its body's straight top, at the top of its feed lips), x toward the front; magazines seat square to the bore.","roles":{"receiver":"magazine","magazine":"receiver"},"compat":[{"param":"family","rule":"equal","optional":false,"message":"Magazine family does not match the magwell (e.g. 5.56 vs pistol-caliber)"}],"beside":[]},"p90_magazine":{"label":"P90 magazine, on top of the upper","description":"FN's P90 magazine laid along the top of an upper made for it. Anchor on the bore's vertical plane at a seated magazine's rear end and underside, x toward the muzzle.","roles":{"receiver":"magazine","magazine":"receiver"},"compat":[],"beside":[]},"picatinny":{"label":"Picatinny rail (MIL-STD-1913)","description":"Anchor origin on the rail top surface at slot 0's center, x toward the muzzle. Index = slot number.","roles":{"rail":"mount","mount":"rail"},"index":{"param":"slot","pitch":"pitch","on":"rail","direction":1,"min":0,"maxParam":"slots"},"compat":[],"beside":[]},"mlok":{"label":"M-LOK","description":"Anchor on the host's axis at the rearmost slot's centre, x toward the muzzle; the host's `faces` say where each face is around it and `face_distance` how far out its surface is. Index = slot number along the face, `face` which face. An accessory's anchor is the middle of its lugs. `lugs` and `reach_inside` on an accessory, `reach_inside` (the room) on the host.","roles":{"slots":"accessory","accessory":"slots"},"index":{"param":"slot","pitch":"pitch","on":"slots","direction":1,"min":0,"maxParam":"slots","face":"face","interval":"interval"},"compat":[{"param":"reach_inside","rule":"at_most","role":"accessory","optional":false,"message":"The accessory reaches further inside the handguard than there is room before what runs through it (the barrel), so it can't be tightened here"}],"beside":[]},"muzzle_thread":{"label":"Muzzle thread","description":"Anchor at the barrel shoulder on the bore axis, x toward the muzzle.","roles":{"barrel":"device","device":"barrel"},"compat":[{"param":"thread","rule":"equal","optional":false,"message":"Thread pitch differs"},{"param":"thread_length","rule":"at_most","role":"barrel","nominal":"thread_length_made_for","nominalMessage":"The barrel's muzzle thread is longer than the one this device is made for, and its maker doesn't say how much longer a thread it takes: whether it seats on the shoulder can't be checked","optional":true,"message":"The barrel's muzzle thread is longer than this device takes, so it wouldn't seat on the shoulder"}],"beside":[]},"scope_rings":{"label":"Scope rings","description":"A scope's main tube in a mount's rings. Anchor on the rings' axis midway between the two rings, x toward the muzzle; the scope's on its optical axis at the middle of its turret saddle. Index = how far forward the scope sits in the rings, in steps of `slide` from where the two anchors meet.","roles":{"rings":"tube","tube":"rings"},"index":{"param":"position","on":"rings","direction":1,"slide":"1mm","clamps":[{"at":"rear_ring","length":"ring_length","from":"rear_from","to":"rear_to"},{"at":"front_ring","length":"ring_length","from":"front_from","to":"front_to"}]},"compat":[{"param":"diameter","rule":"within","tolerance":"0.25mm","optional":false,"message":"The rings are bored for a different tube from the scope's main tube"}],"beside":[]},"optic_footprint":{"label":"Optic footprint","description":"A sight's base on a mount's deck, held by the screws and lug of the pattern both are cut for. Anchor on the deck's top at the pattern's middle, x toward the muzzle; the sight's at the same point of its base. A deck holds one sight, in one place.","roles":{"deck":"base","base":"deck"},"holds":"deck","compat":[{"param":"pattern","rule":"equal","optional":false,"message":"The sight's base is cut for another footprint than the mount's deck"}],"beside":[]},"optic.sight_line":{"label":"Sight and magnifier","description":"What a sight is (how much it magnifies) and what a magnifier is made to sit behind. A check only (the platform's `checks`): both clamp to the rail, and neither is placed by the other.","roles":{"sight":"magnifier","magnifier":"sight","irons":"irons"},"compat":[{"param":"magnification","rule":"equal","optional":false,"message":"A magnifier is made to sit behind a sight that doesn't magnify. A scope needs the eye at its own eye relief, which is where the magnifier would be"}],"align":{"anchor":"optical_axis","message":"A magnifier is set up to stand at the height of the sight it is behind; no maker says how far off still gives the whole view."},"beside":[]},"suppressor_mount":{"label":"Suppressor mount","description":"A muzzle device that a suppressor locks onto. The device's anchor: on the bore axis where the suppressor's rear face stands when locked on, x toward the muzzle. The suppressor's: its rear face, on its axis, x toward the muzzle.","roles":{"device":"suppressor","suppressor":"device"},"compat":[{"param":"system","rule":"equal","optional":false,"message":"The suppressor locks onto another maker's muzzle devices, not this one"}],"beside":[]},"tx22.slide":{"label":"TX22 slide on its frame","description":"The slide on the frame's rails, closed (in battery). Anchor at the slide's rear face on the bore axis, x toward the muzzle: the frame states where a closed slide's rear face stands, the slide's own frame has its origin there.","roles":{"frame":"slide","slide":"frame"},"compat":[],"beside":[]},"tx22.barrel":{"label":"TX22 barrel in its slide","description":"The barrel as it sits in the slide (it comes off the frame with the slide: Taurus's picture of the conversion kit). Anchor at the barrel's breech face on the bore axis, x toward the muzzle: the slide states where the breech face stands, the barrel's own frame has its origin there.","roles":{"slide":"barrel","barrel":"slide"},"compat":[],"beside":[]},"tx22.magwell":{"label":"TX22 magazine in its grip","description":"A magazine seated in the frame's grip. Anchor where the two touch below: the magazine's base pad bearing on the grip's bottom face, at the front of the magazine's body, on the mid-plane, x toward the muzzle.","roles":{"frame":"magazine","magazine":"frame"},"compat":[],"beside":[]}},"finishes":{"finishes":{"anodized":{"label":"Type III hard anodize","recolorable":true,"metalness":0.1,"roughness":0.25,"sheen":{"matte":0.1,"satin":-0.08},"clearcoat":0.35,"detail":"grain","basis":"lookdev","note":"A satin dielectric (D25): the sheen of dyed anodize is the sealed oxide's, and the brief's metalness 0.6 and roughness 0.45 on a near-black dye reflected less than plain plastic, so the receivers rendered flat. Checked against the receivers' flats in Magpul's black-rifle photo (scripts/debug/looks.mjs: the Workhorse's magwell flat reads #424343 against #444245)."},"anodized_matte":{"label":"Matte hard anodize","recolorable":true,"metalness":0.1,"roughness":0.58,"sheen":{"matte":0.1,"satin":-0.12},"detail":"grain","basis":"lookdev","note":"An optic's finish: the metal blasted to a fine matte before it is anodized, so it has a soft, wide highlight and no gloss over it (no clearcoat, where a receiver's sealed anodize has one). The user, 2026-10-05, of SIG's coyote TANGO-MSR drawn as `anodized`: \"The color/finish on the coyote brown scope seems too shiny\". Sportsman's Warehouse lists the black one \"Finish | Matte\". Set against GritrOutdoors' two photos of the coyote scope (references/sig-tango-msr-1-6x24 01b2f17037d8, 9a799bb21e37): its highlights there are wide and soft-edged, with the grain showing in them, and there is no bright line anywhere on it; `anodized` drew a hard white line along the saddle and the tube, and its `matte` sheen left it there. By eye against those two photos: no ratio is read off them (their light isn't the app's)."},"cerakote":{"label":"Cerakote / sprayed ceramic-polymer coating","recolorable":true,"metalness":0,"roughness":0.78,"sheen":{"matte":0.08,"satin":-0.22},"detail":"grain","basis":"lookdev"},"polymer":{"label":"Glass-filled polymer","recolorable":true,"metalness":0,"roughness":0.65,"sheen":{"matte":0.1,"satin":-0.12},"clearcoat":0.08,"detail":"grain","basis":"brief","note":"Roughness 0.65 from the brief; clearcoat is look-dev for the satin skin."},"translucent_polymer":{"label":"Translucent polymer (e.g. smoke magazine bodies)","recolorable":false,"metalness":0,"roughness":0.05,"transmission":1,"ior":1.5,"basis":"lookdev","note":"The colour is the transmittance (what the backdrop reads through the body in the reference photo), applied once. Fully transmissive: a smoke body scatters little, and with any diffuse part the studio's softbox lit it like grey plastic. Glossy, as moulded polycarbonate is: three.js blurs what a transmissive surface shows by its roughness, and at 0.18 the internal webs read as smudges where Black Dog's photo shows them sharp (M5). Its walls, follower and spring aren't drawn (not sourced), so it reads as one tinted volume."},"rubber":{"label":"Rubber / elastomer","recolorable":false,"metalness":0,"roughness":0.9,"basis":"lookdev"},"stainless":{"label":"Brushed stainless","recolorable":false,"metalness":1,"roughness":0.18,"anisotropy":0.35,"basis":"lookdev","note":"The brief specifies \"brushed\"; the numbers are look-dev. Anisotropy (M4 step 4) runs along the barrel: the scene's box-projected UVs give every mesh a tangent frame (M1a's NaN-white barrel had none). Roughness 0.18 and anisotropy 0.35: at 0.3 and 0.6 the step 2 softbox smeared along it and the barrel rendered as a flat white tube (M4 review)."},"steel":{"label":"Phosphate / nitrided steel","recolorable":false,"metalness":0.75,"roughness":0.55,"basis":"lookdev"},"phosphate":{"label":"Manganese phosphate / parkerized steel","recolorable":false,"metalness":0.2,"roughness":0.82,"sheen":{"matte":0.08,"satin":-0.25},"detail":"grain","basis":"lookdev","note":"A conversion coating, not a metal's own face: a matte crystalline layer that scatters, charcoal to grey-green by its bath and its oil (the Army's finish on barrels, carriers and small parts; a maker's \"parkerized\" is the same thing by its trade name). Mostly diffuse, so its colour is matched on photos like a paint's (D24); `steel`, the darker and more metallic of the two, stays for a part whose maker names no finish. Look-dev, 2026-10-06. Looked at the same day beside the photos of the parts drawn in it (the steel parts' colour pass, data/colors/steel.yaml): dry, as Primary Arms photographs BCM's barrel (references/bcm-16-mid-barrel 99b8653ffc94: a soft, wide highlight and no line of light anywhere), the first numbers stand. Oiled, as BCM's carrier and Bear Creek's barrel are photographed (references/bcm-bcg 60260580e01f, bca-556-16-mid-barrel 53fbcf1e58d8: a clear soft highlight along each round), is its `satin`, taken from -0.15 to -0.25: at -0.15 the carrier drew as flat as the barrel. By eye: no ratio is read off the photos."},"nitride":{"label":"Black nitride (QPQ, Melonite) steel","recolorable":false,"metalness":0.7,"roughness":0.32,"sheen":{"matte":0.12,"satin":-0.1},"basis":"lookdev","note":"Salt-bath nitrided and polished steel (\"black nitride\", QPQ, Melonite, Tenifer by their makers): a deep, even black with a soft satin highlight, smoother than phosphate and darker. A photo's brightness on it is reflection: its colour stays a black and isn't fitted to a photo. Look-dev, 2026-10-06. Looked at the same day beside the photos of the parts drawn in it (the steel parts' colour pass): metalness 0.6 to 0.7 and roughness 0.4 to 0.32. At the first numbers a carrier's highlight was as wide and grey as an anodized receiver's; Aero's barrel (references/aero-556-16-mid-barrel 628368f22a19) has one band of light along a black tube, which 0.32 draws, and the carriers (references/toolcraft-556-bcg d3f115e6c8f3, aero-556-bcg a4082e72b225) are a polished black with narrow bright highlights on every edge, which is its `satin` (0.22). By eye: no ratio is read off the photos."},"nickel":{"label":"Electroless nickel (nickel boron, nickel-Teflon) steel","recolorable":false,"metalness":0.9,"roughness":0.36,"sheen":{"matte":0.12,"satin":-0.1},"basis":"lookdev","note":"A plated bright metal with a satin face: silver, a little warm (BCM's PNT trigger: \"An electroless nickel finish is applied\"; Primary Arms calls its colour Silver). A metal: its colour is its reflectance, not a paint's albedo. Look-dev, 2026-10-06."},"glass":{"label":"Coated optical glass","recolorable":false,"metalness":0,"roughness":0.02,"transmission":1,"ior":1.52,"basis":"brief","note":"Transmission with a slight tint (brief); the anti-reflection coating as a thin film (materials.ts, M5): green straight on, violet at an angle, as the HM3X's lenses read in Holosun's photos. Look-dev."}},"details":{"grain":{"tile":0.35,"strength":0.18,"note":"Fine irregular grain: bead-blasted anodize, sprayed coating, a moulded skin."},"stipple":{"tile":0.6,"strength":0.7,"note":"Raised dots ~0.012–0.02 in across (0.6 in per 256-texel tile), the K2+'s grip panels."}},"colors":{"placeholder-black":{"label":"Black (placeholder)","hex":"#1d1e20","calibration":"none","source":"Look-dev placeholder, not a manufacturer color.","family":"placeholder"},"placeholder-polymer-black":{"label":"Polymer black (placeholder)","hex":"#222326","calibration":"none","source":"Look-dev placeholder, not a manufacturer color.","family":"placeholder"},"stainless-natural":{"label":"Natural stainless","hex":"#c8c9c9","calibration":"none","source":"Look-dev, near published F0 reflectance for iron/steel alloys.","family":"metal"},"glass-clear":{"label":"Clear glass","hex":"#f4f7f6","calibration":"none","source":"Look-dev.","family":"other"},"sig-coyote":{"label":"SIG coyote","hex":"#80544a","calibration":"appearance","source":"make color-match, 2026-10-06: the coyote TANGO-MSR's objective bell in the hero direction (light backdrop, build `suppressed`, the scope and its mount in coyote), under anodized_matte, fitted to the lit flats of GritrOutdoors' two 1600 px photos of the coyote scope, SOTM61200 (references/sig-tango-msr-1-6x24 01b2f17037d8 and 9a799bb21e37: #77564d and #6d4c44, their mean #72514a); rendered #72514a for a target of #72514a, and the eyepiece in the same render reads #74544d. Until then it was #5b392c, from scripts/color-match.mjs: the scope and its mount in the right side view (light backdrop, build `suppressed`) matched to GritrOutdoors' two 1600 px photos of the coyote TANGO-MSR, SOTM61200 (references/sig-tango-msr-1-6x24 01b2f17037d8 and 9a799bb21e37; tools/color_sample.py reads #5d443c and #5a4139, a dark brown): renders #5c433b against their mean #5c433b. Matched again on 2026-10-05 under the matte finish the two are drawn in since (`anodized_matte`): the albedo matched under `anodized`, #6e4b3d, renders lighter on a matte surface (#6c5046), as a matte surface sends more of its own colour to the eye. Xtreme Guns and Ammo's 650 px photo of the same scope (6eed7e5f115c) reads lighter and pinker, #957b70, and was the value until the review (M6): one retailer's exposure against another's, with nothing from SIG to settle it. That older fit compared the whole scope's median in the photos (its shadowed underside with its lit flank) with the app's right side view, the side the app's light doesn't fall on; every other preset is fitted on a lit flat in the hero direction, where the old value drew a dark chocolate (#543e37 on the bell) under photos that read #72514a there (D81).","family":"metal"},"silencerco-black-oxide":{"label":"SilencerCo black oxide (as photographed)","hex":"#4b4a4d","calibration":"none","source":"tools/color_sample.py on Primary Arms' side view of the Sparrow 22 (references/silencerco-sparrow-22 7610478aca44): median sRGB of the body's interior, 10th to 85th luminance percentile. A studio photo of a matte dark metal: the reading includes the lights' sheen, so the surface itself is likely darker.","family":"metal"},"blackdog-smoke":{"label":"Black Dog smoke (translucent)","hex":"#8a8881","calibration":"none","source":"tools/color_sample.py on Black Dog's photo SMOKEANDBLACKCOLORS.jpg (references/blackdog-22lr-15, sha256 prefix d10099a31a30), 10-round body ROI [340,132,482,447]: median sRGB seen through the body against a white backdrop. Includes the follower and spring.","family":"other"},"blackdog-smoke-edge":{"label":"Black Dog smoke, seen edge-on (internal webs)","hex":"#353330","calibration":"none","source":"tools/color_sample.py on the webs' cores in the Sonic X side view (references/blackdog-22lr-15 0eb77371d877, rows 462–478, 680–694, 897–912 over x 1100–1170: #383430, #2f2d29, #353330): the smoke plastic seen through its thickness, behind a wall.","family":"other"},"blackdog-black-sample":{"label":"Black Dog black (photo sample, reference only)","hex":"#505458","calibration":"none","source":"tools/color_sample.py, same photo, ROI [493,125,640,442]. Reads lighter than the real albedo because sheen and exposure get averaged in, so it isn't used for rendering yet (M4 calibrates against the backdrop).","family":"other"},"magpul-black":{"label":"Magpul Black","hex":"#111111","calibration":"appearance","source":"scripts/color-match.mjs: the MOE SL's flat side in the hero view (light backdrop, M4 step 2 light) matched to the stock in Magpul's rifle photos on Big Tex Ordnance's MOE SL listing (references/magpul-moe-sl-carbine 37c122764a68 FDE, 64f9135baa1f black, 964ce038d18a ODG: one rifle with black anodized receivers, the furniture swapped): renders #323232 against #303030; the softbox's reflection in the satin polymer floors it there (albedo #1a1a1a reads #343434), as the photo's black is mostly sheen too. The grip, a check, #2b2b2b against #393939.","family":"magpul"},"magpul-fde":{"label":"Magpul Flat Dark Earth","hex":"#8c7556","calibration":"appearance","source":"scripts/color-match.mjs: the MOE SL's flat side in the hero view (light backdrop, M4 step 2 light) matched to the stock in Magpul's rifle photos on Big Tex Ordnance's MOE SL listing (references/magpul-moe-sl-carbine 37c122764a68 FDE, 64f9135baa1f black, 964ce038d18a ODG: one rifle with black anodized receivers, the furniture swapped): renders #7a6853 against #7a6853; the grip, a check, #78664f against #847361.","family":"magpul"},"magpul-odg":{"label":"Magpul OD Green","hex":"#413520","calibration":"appearance","source":"scripts/color-match.mjs: the MOE SL's flat side in the hero view (light backdrop, M4 step 2 light) matched to the stock in Magpul's rifle photos on Big Tex Ordnance's MOE SL listing (references/magpul-moe-sl-carbine 37c122764a68 FDE, 64f9135baa1f black, 964ce038d18a ODG: one rifle with black anodized receivers, the furniture swapped): renders #463f36 against #463f34; the grip, a check, #423b30 against #514a3e. The albedo is more saturated than the render because the polymer's sheen adds neutral grey, as it does in the photo.","family":"magpul"},"magpul-stealth-gray":{"label":"Magpul Stealth Gray","hex":"#4e4f53","calibration":"appearance","source":"scripts/color-match.mjs, like the others, to a target predicted for the rifle photos' light: two sets of Magpul's K2+ catalog shots (references/magpul-moe-k2-plus set A c773df52fda1 / 869463939860 / 858e9042147b / 5cff1c897341, set B 0f2dcecc75e7 / 72d990bb5374 / 927418fbea1a / ca9715288373) show it with black, ODG and FDE; a gain and offset in linear light, shared by the channels, maps each set's three onto the rifle photo's stocks, and takes its Stealth Gray to #4f4e53 (A) and #4d4e50 (B); target #4e4e51 (renders #4e4e51 against it in the M4 step 2 light)","family":"magpul","note":"Two steps from the reference photo instead of one. The map's residuals on the three shared colours reach 0.014–0.018 in linear light (the rifle photo's ODG is browner than the catalog shots'), so read it as ±3 sRGB levels on top of the others' uncertainty."},"aero-fde-cerakote":{"label":"Aero FDE Cerakote","hex":"#c7a88c","calibration":"appearance","source":"make color-match: the M4E1 Threaded upper's left side under its rail in the hero direction, light backdrop, build aero-556 (no sight), under cerakote, fitted to three of Aero's photos of its FDE Cerakote receivers, each on a flat that stands upright to the lens: the strip under the port of the upper APAR700202C (references/aero-m4e1-threaded-upper d52b7991fc46, region [480,350,800,392], reads #a88c79), the complete lower APAR600102 behind its trigger pin (references/aero-m4e1-lower 7afd45524a9c, region [645,203,735,230], reads #ac9178) and the stripped lower APAR600002C there (199354d2da14, region [330,240,500,285], reads #af9883); rendered #ac927b for a target of #ac917b","family":"cerakote","note":"The three flats agree within 9 levels. What Aero's light falls on is far lighter (the upper's sloped left face reads #caaf9c) and what it doesn't is darker (its lower body #907969, where the app's band toward the underside renders #99826d; the lowers' magazine wells #9a826a and #827061). Aero's Finish rows call it \"Magpul FDE Cerakote\". Matched on the upper, and drawn on the complete lower's receiver at the same colour: the lower's own flat couldn't be sampled in the tool (its stock stands where the tool reads the backdrop's level)."},"aero-kodiak-brown-7075":{"label":"Aero Kodiak Brown anodize (receivers)","hex":"#917767","calibration":"appearance","source":"make color-match: the M4E1 Threaded upper's left side under its rail in the hero direction, light backdrop, build aero-556 (no sight), under anodized (matte), fitted to Aero's two photos of APAR700222C: its left side's lit sloped face (references/aero-m4e1-threaded-upper 6ee423b705e6, region [420,265,840,298], reads #7d6f66) and the strip under the port on its right side (4e1c290e1d51, region [480,350,800,392], reads #806659); rendered #7f6b5f for a target of #7f6b60","family":"anodize","note":"The two photos are 13 levels apart in blue: the right view is a redder brown than the left (two receivers, or two days' light). The band below, toward the receiver's underside, renders #6f5d51 where the left photo's lower body, in its own shadow, reads #594c46: the app lights that side more evenly than Aero's studio. Aero's 6061 handguards in the anodize of this name are lighter and pinker (aero-kodiak-brown-6061)."},"aero-od-green-anodize-7075":{"label":"Aero OD Green anodize (receivers)","hex":"#8b9867","calibration":"appearance","source":"make color-match: the M4E1 Threaded upper's left side under its rail in the hero direction, light backdrop, build aero-556 (no sight), under anodized (matte), fitted to Aero's two photos of APAR700220C: its left side's lit sloped face (references/aero-m4e1-threaded-upper 8da1f0a429be, region [420,265,840,298], reads #7f8868) and the strip under the port on its right side (7263e3f8e030, region [480,350,800,392], reads #747f58); rendered #7a845f for a target of #7a8460","family":"anodize","note":"The two photos are 9 to 16 levels apart (the right view darker and less blue). The band toward the underside renders #6b7451 where the left photo's lower body, in shadow, reads #5b6147. Aero's 6061 handguards in the anodize of this name are a yellower olive (aero-od-green-anodize-6061)."},"aero-kodiak-brown-6061":{"label":"Aero Kodiak Brown anodize (handguards)","hex":"#bd9988","calibration":"appearance","source":"make color-match: the 15 in R-ONE's left side face on the solid block at its rear in the hero direction, light backdrop, build aero-556 (no sight), under anodized (matte), fitted to Aero's two photos of APRA501401A: the same face in its right view (references/aero-r-one-15-handguard b122b6045c79, region [50,303,180,330], reads #aa8e80) and its left view (88a1f366f7dc, region [825,303,940,330], reads #a58a7f); rendered #a88c80 for a target of #a88c80","family":"anodize","note":"Read on the side face, which Aero's light falls on: the faces above and below it are far darker in the photos (in shadow) than the app draws them. Small regions (1,200 to 1,400 px of a 1000 px photo)."},"aero-od-green-anodize-6061":{"label":"Aero OD Green anodize (handguards)","hex":"#9a8b53","calibration":"appearance","source":"make color-match: the 15 in R-ONE's left side face on the solid block at its rear in the hero direction, light backdrop, build aero-556 (no sight), under anodized (matte), fitted to Aero's two photos of APRA501178A: the same face in its right view (references/aero-r-one-15-handguard 484b835aa946, region [50,303,180,330], reads #8e8259) and its left view (8300948f5109, region [825,303,940,330], reads #8c825f); rendered #8d825c for a target of #8d825c","family":"anodize","note":"A bronze olive, as Aero's photos of the handguard have it; its receivers in OD Green Anodized are greener. Small regions (1,200 to 1,400 px)."},"aero-od-green-cerakote":{"label":"Aero OD Green Cerakote","hex":"#665f4a","calibration":"appearance","source":"make color-match: the 15 in R-ONE's left side face on the solid block at its rear in the hero direction, light backdrop, build aero-556 (no sight), under cerakote, fitted to Aero's two photos of APRA501402A: the same face in its right view (references/aero-r-one-15-handguard 679f4bacfe1f, region [50,303,180,330], reads #645e4f) and its left view (a6b5c43efbb5, region [825,303,940,330], reads #4f4c3d); rendered #5a5546 for a target of #5a5546","family":"cerakote","note":"The two views are 21 levels apart: the right view's rear end is lit lighter than the left's. Both are Aero's own and the same size, so the target is their mean, and the colour is good to about ten levels either way. Aero's Finish row calls it \"Magpul OD Cerakote\"."},"aero-socom-blue":{"label":"Aero SOCOM Blue Cerakote","hex":"#3a4146","calibration":"appearance","source":"make color-match: the 15 in R-ONE's left side face on the solid block at its rear in the hero direction, light backdrop, build aero-556 (no sight), under cerakote, fitted to Aero's two photos of APRA501643A: the same face in its right view (references/aero-r-one-15-handguard 3e51d0ad3489, region [50,303,180,330], reads #404549) and its left view (af00888aabfb, region [825,303,940,330], reads #353a3d); rendered #3b4043 for a target of #3b4043","family":"cerakote","note":"A blue charcoal, 11 levels apart between the two views; the black anodized handguard reads #3b373c and #3c3a3e on the same face, as dark and without the blue. Matched because it is a matte sprayed coat and plainly bluer than the black."},"aero-sniper-grey-cerakote":{"label":"Aero Sniper Grey Cerakote","hex":"#676b6a","calibration":"appearance","source":"make color-match: the M4E1 stripped lower's left side, the flat under its trigger pin, in the hero direction, light backdrop, build bcm-16-mid with that lower (no trigger guard: its own), under cerakote, fitted to Aero's photo of APAR600072C, this receiver in the coat (references/aero-m4e1-stripped-lower ee28352d2741, the flat behind its trigger pin, region [330,240,500,285], reads #5a5c5b); rendered #595c5b for a target of #5a5c5b","family":"cerakote","note":"One photo, Aero's own right side view of the stripped lower in this coat, and no second on file. A neutral grey: its three channels within two levels. The photo's magazine well reads darker (#494b4a above the logo, #525453 under it) where the app's well's wall renders the flat's own #595c5b: the app lights that side more evenly than Aero's studio. Aero's Finish row: \"Sniper Grey Cerakote\". Corroborated on the 15 in R-ONE in 2026-10-28 maker photos 2cdc199a1372 and 4c83842bb8a7: the side face reads #5e6163 and #4b4c4e at [60,309,180,327] and [825,309,940,327]. make color-match aero-colorways-check renders #5b5e5d on that face in the hero direction, within eight levels of their mean and within the two-photo spread; the existing preset is retained. And on the M4E1 Threaded assembled upper (2026-11-02): Aero's left view of APAR700272AC (references/aero-m4e1-threaded-upper b3b5eb2376e4) reads the band under the rail #444545 and the sloped flat below it #7a7c7b, mean #5f6160; the app in the same view (make color-match, view from the left, the colour as it is) renders the two #5a5c5c and #5e6160, mean #5c5e5e, within three levels of the photo's; the app lights the two faces more evenly than Aero's studio does."},"aero-fde-cerakote-handguards":{"label":"Aero FDE Cerakote (handguards)","hex":"#a98b72","calibration":"appearance","source":"Aero configurable product galleries, retrieved 2026-10-28; each exact 15 in variant has right/left views: APRA500715A 45cc70e3d695 [60, 309, 180, 327] #917a67; APRA500715A 5ac5e2604e2f [825, 309, 940, 327] #87725f; APRA500115A 6c3cc51f4db1 [60, 309, 180, 327] #947b65; APRA500115A a8315b731c7d [825, 309, 940, 327] #8a715d. Lit side face at the solid rear block, tools/color_sample.py. make color-match (aero-colorways-fit, 2026-10-28): the 15 in R-ONE solid rear block's left side face under cerakote, hero direction [0.45, 0.3, -1], light backdrop, camera target [7.6, 1.1, 0], distance 8, render region [800, 555, 1040, 630]; albedo #a98b72 renders #8e7663 for the four-photo target #8e7662.","family":"cerakote","note":"The R-ONE and S-ONE pairs agree within three levels in their means; this handguard preset preserves the distinctly lighter receiver FDE preset. The right and left photographs differ by up to ten levels. The galleries' registered edges do not match a single recolored photo (correlations 0.60-0.90 across these colors); the side walls and coating texture differ. Camera exposure, lighting and white balance remain those of the maker's studio."},"aero-burnt-bronze-cerakote":{"label":"Aero Burnt Bronze Cerakote","hex":"#ab8a66","calibration":"appearance","source":"Aero configurable product galleries, retrieved 2026-10-28; each exact 15 in variant has right/left views: APRA500775A 667b46b13955 [60, 309, 180, 327] #9d7f63; APRA500775A f5a23788580b [825, 309, 940, 327] #856c53; APRA500175A 408400db30ec [60, 309, 180, 327] #a18362; APRA500175A 5d92042d4fed [825, 309, 940, 327] #7f674f. Lit side face at the solid rear block, tools/color_sample.py. make color-match (aero-colorways-fit, 2026-10-28): the 15 in R-ONE solid rear block's left side face under cerakote, hero direction [0.45, 0.3, -1], light backdrop, camera target [7.6, 1.1, 0], distance 8, render region [800, 555, 1040, 630]; albedo #ab8a66 renders #90755a for the four-photo target #90755a.","family":"cerakote","note":"The R-ONE and S-ONE pairs agree within three levels in their means; a shared preset fits both. The right and left photographs differ by up to 34 levels, so this is their mean appearance, not a guarantee that any specimen will match exactly. The galleries' registered edges do not match a single recolored photo (correlations 0.60-0.90 across these colors); the side walls and coating texture differ. Camera exposure, lighting and white balance remain those of the maker's studio."},"aimpoint-dark-gray":{"label":"Aimpoint dark gray (the Micro's housing)","hex":"#312e2b","calibration":"appearance","source":"make color-match: aimpoint-micro-t-2's housing, its left flank, in the hero direction, light backdrop, build v1 with the sight in the red dot's place, under anodized_matte, fitted to the housing's flank in references/aimpoint-micro-t-2 10c377094e97 (Aimpoint's own left profile of 200198 as Bravo Company shows it, region [450,620,750,800], reads #3b383b) and 2a4123f4346e (Atlantic Tactical's photograph of one from the front left, region [230,180,440,260], #393836); rendered #3a3837 for a target of #3a3837","family":"anodize","note":"A dark gray with a warm cast, a little lighter than the black of the mount under it (the manual: \"black to dark gray\"). The check on the same render: the spacer, in the placeholder black every black optic has, renders #2f2f30 where Aimpoint's picture has it #2e2d31, so the two photos' light is near the app's. Higher on the housing, where the pictures' key light falls, it reads #4f4d4e and #575457: the flank's reading is the one taken."},"aimpoint-lrp-lever":{"label":"Aimpoint LRP lever","hex":"#ebe3c5","calibration":"appearance","source":"make color-match: aimpoint-micro-t-2's lever, its grip's flat on the mount's left side, in the hero direction, light backdrop, build v1 with the sight in the red dot's place, under anodized_matte, fitted to the lever in references/aimpoint-micro-t-2 61f02b95d3de (Atlantic Tactical's photograph of a 200198 from the right rear, the lever's tip, region [22,480,60,505], reads #c1baa2); rendered #c1baa2 for a target of #c1baa2","family":"metal","note":"A pale, warm metal. The seller's photograph is taken, not Aimpoint's own pictures, which have the lever lighter than a matte surface can be under the app's light: #dac9b9 on the left profile (references/aimpoint-micro-t-2 10c377094e97, region [760,1425,1150,1475]) and #cfbfae on the quarter view; fitted to the first, the colour stopped at the matcher's ceiling (#f3f3e2) and rendered #c7c7b9, its warmth lost. The seller's reading is a small one (333 px of a 600 px photo); the same lever where the sight shades it, in that seller's other photograph (2a4123f4346e), reads #a59e84. What the lever is made of and how it is finished is on no page on file: the finish type is the mount's, by its look."},"b5-fde":{"label":"B5 Flat Dark Earth","hex":"#786b57","calibration":"appearance","source":"make color-match: b5-enhanced-sopmod-stock's housing (its left flat, the face the app's light falls on) in the hero direction, light backdrop, build bcm-16-mid, under polymer (satin), fitted to the lever's flat, the lit face in B5's own pictures: references/b5-enhanced-sopmod-stock 4ad1e80354f6 (B5, SOP-1075_PROFILE_RIGHT.png, region [1003,951,1383,996], reads #7a7062) and references/b5-bravo-stock 19166c4b6f58 (B5, BRV-1085_PROFILE_RIGHT.png, [999,951,1329,996], #776e61); rendered #786f62 for a target of #786f62","family":"polymer","note":"Both readings are B5's own, of two stocks: no seller's photo agrees with them. Primary Arms' own photo of the Enhanced SOPMOD (792f4b2667db) reads its housing #a69d8e and Wing Tactical's (c74dbf598a8f) #c1b197, where B5's pictures read the housing #6a6154 and #5e5548 (it leans from the light there, and the lever's flat, which faces it, is the reading taken). The three sources' blacks are near each other (#36373a, #333333, #4d4d4d), so it is not one exposure apart: the maker's own is drawn, and the colour may be lighter than this."},"b5-coyote-brown":{"label":"B5 Coyote Brown","hex":"#78552e","calibration":"appearance","source":"make color-match: b5-enhanced-sopmod-stock's housing (its left flat, the face the app's light falls on) in the hero direction, light backdrop, build bcm-16-mid, under polymer (satin), fitted to the lever's flat, the lit face in B5's own pictures: references/b5-enhanced-sopmod-stock a2377e875455 (B5, SOP-1076_PROFILE_RIGHT.png, region [1023,966,1403,1011], reads #75604a) and references/b5-bravo-stock f6b0d8a39865 (B5, BRV-1086_PROFILE_RIGHT.png, [1025,971,1355,1016], #7b624d); rendered #78614e for a target of #78614c","family":"polymer","note":"Both readings are B5's own, of two stocks: no seller's photo agrees with them. Primary Arms' own photo of the Enhanced SOPMOD (c618e80428e6) reads its housing #856242, and T.REX ARMS' coyote stocks are a yellower, lighter tan under their own light, where B5's pictures read the housing #634e37 and #665039 (it leans from the light there, and the lever's flat, which faces it, is the reading taken). The three sources' blacks are near each other (#36373a, #333333, #4d4d4d), so it is not one exposure apart: the maker's own is drawn, and the colour may be lighter than this."},"b5-od-green":{"label":"B5 OD Green","hex":"#3d3a17","calibration":"appearance","source":"make color-match: b5-enhanced-sopmod-stock's housing (its left flat, the face the app's light falls on) in the hero direction, light backdrop, build bcm-16-mid, under polymer (satin), fitted to the lever's flat, the lit face in B5's own pictures: references/b5-enhanced-sopmod-stock 6db640b1df3c (B5, SOP-1097_PROFILE_RIGHT.png, region [1008,954,1388,999], reads #4e4d38) and references/b5-bravo-stock 60e89d6c78b6 (B5, BRV-1104_PROFILE_RIGHT.png, [1011,964,1341,1009], #55533e); rendered #555347 for a target of #52503b","family":"polymer","note":"Both readings are B5's own, of two stocks: no seller's photo agrees with them. Wing Tactical's photo of the Enhanced SOPMOD (c74dbf598a8f) reads its housing #706e59 (Primary Arms' two OD green photos are B5's own pictures by their names and their light), where B5's pictures read the housing #45412f and #3c3d2a (it leans from the light there, and the lever's flat, which faces it, is the reading taken). The three sources' blacks are near each other (#36373a, #333333, #4d4d4d), so it is not one exposure apart: the maker's own is drawn, and the colour may be lighter than this. The fit was stopped at its third step: the blue kept falling (#39370e at the fifth, for one level more) because the polymer's sheen adds a grey the target hasn't."},"b5-wolf-grey":{"label":"B5 Wolf Grey","hex":"#4a4c48","calibration":"appearance","source":"make color-match: b5-enhanced-sopmod-stock's housing (its left flat, the face the app's light falls on) in the hero direction, light backdrop, build bcm-16-mid, under polymer (satin), fitted to the lever's flat, the lit face in B5's own pictures: references/b5-enhanced-sopmod-stock 5617581aa523 (B5, SOP-1123_PROFILE_RIGHT.png, region [1010,954,1390,999], reads #545552) and references/b5-bravo-stock c502cb5e6ad4 (B5, BRV-1117_PROFILE_RIGHT.png, [1010,963,1340,1008], #626461); rendered #5b5c5a for a target of #5b5c5a","family":"polymer","note":"Both readings are B5's own, of two stocks: no seller's photo agrees with them. No seller's own photo of it is on file (Primary Arms' two are B5's own pictures by their names and their light), where B5's pictures read the housing #444543 and #494c49 (it leans from the light there, and the lever's flat, which faces it, is the reading taken). The three sources' blacks are near each other (#36373a, #333333, #4d4d4d), so it is not one exposure apart: the maker's own is drawn, and the colour may be lighter than this."},"b5-fde-rubber":{"label":"B5 Flat Dark Earth (butt pad)","hex":"#796b59","calibration":"appearance","source":"make color-match: b5-enhanced-sopmod-stock's butt pad, its left side in the hero direction, light backdrop, build bcm-16-mid, under rubber, fitted to a target predicted for the app's light. B5's pictures read the pad's side (references/b5-enhanced-sopmod-stock 4ad1e80354f6 [233,601,283,1371] #7e7466; references/b5-bravo-stock 19166c4b6f58 [264,621,324,1171] #6e6457; mean #766c5e) beside the lever's flat (#786f62), two faces square to the camera; that ratio in linear light, a channel at a time, of what the app renders b5-fde as on a face like the pad's (the web under the QD socket, #695f52) is #675c4f; rendered #675c4f for a target of #675c4f","family":"other","note":"The pad beside the polymer, as B5's pictures have the two: fitted to its own reading it came out far paler than the stock, because the app's light falls on the housing and B5's on the pad's side. As uncertain as the polymer's colour is, and with it."},"b5-coyote-brown-rubber":{"label":"B5 Coyote Brown (butt pad)","hex":"#8d7055","calibration":"appearance","source":"make color-match: b5-enhanced-sopmod-stock's butt pad, its left side in the hero direction, light backdrop, build bcm-16-mid, under rubber, fitted to a target predicted for the app's light. B5's pictures read the pad's side (references/b5-enhanced-sopmod-stock a2377e875455 [253,616,303,1386] #887562; references/b5-bravo-stock f6b0d8a39865 [290,641,350,1191] #877461; mean #887462) beside the lever's flat (#78614c), two faces square to the camera; that ratio in linear light, a channel at a time, of what the app renders b5-coyote-brown as on a face like the pad's (the web under the QD socket, #69503a) is #77604c; rendered #77604c for a target of #77604c","family":"other","note":"The pad beside the polymer, as B5's pictures have the two: fitted to its own reading it came out far paler than the stock, because the app's light falls on the housing and B5's on the pad's side. As uncertain as the polymer's colour is, and with it."},"b5-od-green-rubber":{"label":"B5 OD Green (butt pad)","hex":"#565643","calibration":"appearance","source":"make color-match: b5-enhanced-sopmod-stock's butt pad, its left side in the hero direction, light backdrop, build bcm-16-mid, under rubber, fitted to a target predicted for the app's light. B5's pictures read the pad's side (references/b5-enhanced-sopmod-stock 6db640b1df3c [238,604,288,1374] #66644f; references/b5-bravo-stock 60e89d6c78b6 [276,634,336,1184] #5d5e4b; mean #62614d) beside the lever's flat (#52503b), two faces square to the camera; that ratio in linear light, a channel at a time, of what the app renders b5-od-green as on a face like the pad's (the web under the QD socket, #403f30) is #4d4d3f; rendered #4d4d3f for a target of #4d4d3f","family":"other","note":"The pad beside the polymer, as B5's pictures have the two: fitted to its own reading it came out far paler than the stock, because the app's light falls on the housing and B5's on the pad's side. As uncertain as the polymer's colour is, and with it."},"b5-wolf-grey-rubber":{"label":"B5 Wolf Grey (butt pad)","hex":"#6c6f67","calibration":"appearance","source":"make color-match: b5-enhanced-sopmod-stock's butt pad, its left side in the hero direction, light backdrop, build bcm-16-mid, under rubber, fitted to a target predicted for the app's light. B5's pictures read the pad's side (references/b5-enhanced-sopmod-stock 5617581aa523 [240,604,290,1374] #71726f; references/b5-bravo-stock c502cb5e6ad4 [275,633,335,1183] #747572; mean #727470) beside the lever's flat (#5b5c5a), two faces square to the camera; that ratio in linear light, a channel at a time, of what the app renders b5-wolf-grey as on a face like the pad's (the web under the QD socket, #4a4b48) is #5d5f5a; rendered #5d5f59 for a target of #5d5f5a","family":"other","note":"The pad beside the polymer, as B5's pictures have the two: fitted to its own reading it came out far paler than the stock, because the app's light falls on the housing and B5's on the pad's side. As uncertain as the polymer's colour is, and with it."},"b5-fde-steel":{"label":"B5 Flat Dark Earth (steel hardware)","hex":"#7b6c5b","calibration":"appearance","source":"make color-match: b5-enhanced-sopmod-stock's QD socket, its left face in the hero direction, light backdrop, build bcm-16-mid, under cerakote, fitted to a target predicted for the app's light. B5's pictures read the steel (the socket's face, a ring 46 to 55 px about its hole, and the lock pin's end: references/b5-enhanced-sopmod-stock 4ad1e80354f6 #84796d and #7c7064; references/b5-bravo-stock 19166c4b6f58 #6f6559 and #716659; mean #786d61) beside the lever's flat (#786f62); that ratio in linear light, a channel at a time, of what the app renders b5-fde as on the web round the socket (#695f52) is #695d51; rendered #695d51 for a target of #695d51","family":"other","note":"The coat on B5's colour matched steel hardware, which B5 doesn't name: drawn as a matte sprayed coat. Small faces (2,000 to 3,600 px a reading), and the four readings span up to 22 levels a channel on one colour (OD green): the steel is the stock's colour within that."},"b5-coyote-brown-steel":{"label":"B5 Coyote Brown (steel hardware)","hex":"#876649","calibration":"appearance","source":"make color-match: b5-enhanced-sopmod-stock's QD socket, its left face in the hero direction, light backdrop, build bcm-16-mid, under cerakote, fitted to a target predicted for the app's light. B5's pictures read the steel (the socket's face, a ring 46 to 55 px about its hole, and the lock pin's end: references/b5-enhanced-sopmod-stock a2377e875455 #836a55 and #7e6955; references/b5-bravo-stock f6b0d8a39865 #846b57 and #85725f; mean #826c58) beside the lever's flat (#78614c); that ratio in linear light, a channel at a time, of what the app renders b5-coyote-brown as on the web round the socket (#69503a) is #725944; rendered #725944 for a target of #725944","family":"other","note":"The coat on B5's colour matched steel hardware, which B5 doesn't name: drawn as a matte sprayed coat. Small faces (2,000 to 3,600 px a reading), and the four readings span up to 22 levels a channel on one colour (OD green): the steel is the stock's colour within that."},"b5-od-green-steel":{"label":"B5 OD Green (steel hardware)","hex":"#4d4d38","calibration":"appearance","source":"make color-match: b5-enhanced-sopmod-stock's QD socket, its left face in the hero direction, light backdrop, build bcm-16-mid, under cerakote, fitted to a target predicted for the app's light. B5's pictures read the steel (the socket's face, a ring 46 to 55 px about its hole, and the lock pin's end: references/b5-enhanced-sopmod-stock 6db640b1df3c #676953 and #5c5c46; references/b5-bravo-stock 60e89d6c78b6 #53523f and #52513f; mean #5a5a46) beside the lever's flat (#52503b); that ratio in linear light, a channel at a time, of what the app renders b5-od-green as on the web round the socket (#403f30) is #474739; rendered #474739 for a target of #474739","family":"other","note":"The coat on B5's colour matched steel hardware, which B5 doesn't name: drawn as a matte sprayed coat. Small faces (2,000 to 3,600 px a reading), and the four readings span up to 22 levels a channel on one colour (OD green): the steel is the stock's colour within that."},"b5-wolf-grey-steel":{"label":"B5 Wolf Grey (steel hardware)","hex":"#54554e","calibration":"appearance","source":"make color-match: b5-enhanced-sopmod-stock's QD socket, its left face in the hero direction, light backdrop, build bcm-16-mid, under cerakote, fitted to a target predicted for the app's light. B5's pictures read the steel (the socket's face, a ring 46 to 55 px about its hole, and the lock pin's end: references/b5-enhanced-sopmod-stock 5617581aa523 #5a5a57 and #575854; references/b5-bravo-stock c502cb5e6ad4 #626260 and #5e5f5c; mean #5c5d5a) beside the lever's flat (#5b5c5a); that ratio in linear light, a channel at a time, of what the app renders b5-wolf-grey as on the web round the socket (#4a4b48) is #4b4c48; rendered #4c4c48 for a target of #4b4c48","family":"other","note":"The coat on B5's colour matched steel hardware, which B5 doesn't name: drawn as a matte sprayed coat. Small faces (2,000 to 3,600 px a reading), and the four readings span up to 22 levels a channel on one colour (OD green): the steel is the stock's colour within that."},"bcm-fde":{"label":"BCM Flat Dark Earth","hex":"#bbaa92","calibration":"appearance","source":"make color-match: the Stock Mod 0's cheek flat in the hero direction, light backdrop, build bcm-16-mid, under polymer (matte), fitted to references/bcm-stock-mod-0 eca7b267c2b2 (BCM's own photo of the Flat Dark Earth stock, 2020, region [1420,540,2060,770], reads #9a8d7b) and a7a4065dc6ed (Dirty Bird's BCM-GFS-MOD-0-FDE_2_HR, region [900,500,1500,800], #9f907c); rendered #9d8f7c for a target of #9d8f7c","family":"polymer","note":"The colour of what BCM has photographed since 2020. Its own photo of the Flat Dark Earth grip reads a little redder (references/bcm-grip-mod-3 bdf41efeff9d, #a28c77); SAO Supply's of the stock #a39683. Older pictures are a lighter, yellower tan and aren't what this is fitted to: the distributor's BCM-GFS-MOD-0-FDE_1_HR #e3d1a8, Wing's stock #c1af98 and grip #bbb09e, Dirty Bird's four grips #ccbd9d."},"bcm-foliage-green":{"label":"BCM Foliage Green","hex":"#d8d8b3","calibration":"appearance","source":"make color-match: the Stock Mod 0's cheek flat in the hero direction, light backdrop, build bcm-16-mid, under polymer (matte), fitted to references/bcm-stock-mod-0 7228e3bd7b8b (Bauer Precision's BCM-GFS-MOD-0-FG_1_HR, the distributor's photo, region [240,260,760,500], reads #b9b797) and references/bcm-grip-mod-3 a705fc36fe4b (Dirty Bird's BCM-GFG-MOD-3-FGREEN_2_HR, region [600,480,900,640], #b0af95); rendered #b4b396 for a target of #b4b396","family":"polymer","note":"No photo of BCM's own shows this colour (its shop has no page for it): both are the distributor's, of one bright series in which black reads #494845, so it may sit a little light beside the Flat Dark Earth, which is fitted to BCM's own darker exposures. Dirty Bird's four grips in one picture have it at #b2b198."},"bcm-foliage-green-rubber":{"label":"BCM Foliage Green (butt pad)","hex":"#e1e0bc","calibration":"appearance","source":"make color-match: the Stock Mod 0's butt pad, its side band in the hero direction, light backdrop, build bcm-16-mid, under rubber, fitted to the body's own target: in references/bcm-stock-mod-0 7228e3bd7b8b (Bauer Precision's BCM-GFS-MOD-0-FG_1_HR) the pad is the body's green, #b9b797 on the body and #989574 on the pad's shadowed edge (region [1170,300,1215,900]); rendered #b4b396 for a target of #b4b396","family":"other","note":"One photograph, of the earlier kind of stock, whose pad was the stock's colour. The pad's own reading is its edge in shadow, so the body's is the target: the photo shows no step in tone between them on the lit side."},"bcm-wolf-gray":{"label":"BCM Wolf Gray","hex":"#b6b7b7","calibration":"appearance","source":"make color-match: the Stock Mod 0's cheek flat in the hero direction, light backdrop, build bcm-16-mid, under polymer (matte), fitted to references/bcm-stock-mod-0 1b08531b0a85 (GunGear's BCM-GFS-MOD-0-WG_2_HR, the distributor's photo, region [690,410,1620,780], reads #969696) and a0647d7e661f (its WG_3_HR, region [375,500,1310,810], #9b9b9b); rendered #999999 for a target of #999999","family":"polymer","note":"A neutral mid grey in both. The grip in this colour reads a little lighter in Dirty Bird's photo (references/bcm-grip-mod-3 2f57f03b9273, #a6a9a6) and the stock from behind a little darker and warmer (9368820c28c7, #8b8c86). No photo of BCM's own in white light shows it (its brochure's, page 8, is lit low)."},"bcm-pad-gray":{"label":"BCM butt pad, dark grey","hex":"#525457","calibration":"appearance","source":"make color-match: the Stock Mod 0's butt pad, its side band in the hero direction, light backdrop, build bcm-16-mid, under rubber, fitted to references/bcm-stock-mod-0 eca7b267c2b2 (BCM's own photo of the Flat Dark Earth stock, region [540,470,600,560], reads #424448) and 1b08531b0a85 (GunGear's BCM-GFS-MOD-0-WG_2_HR, region [50,470,105,1250], #4b4b4b); rendered #47484a for a target of #47484a","family":"other","note":"The pad of the Flat Dark Earth and the Wolf Gray stock as photographed since 2020: a charcoal, lighter than the black stock's pad. SAO Supply's photo of the Flat Dark Earth stock has it at #4a4a4a. Small regions (a band 60 px wide)."},"bcm-fde-cerakote":{"label":"BCM Flat Dark Earth Cerakote","hex":"#877e7a","calibration":"appearance","source":"make color-match: the MCMR-15's side face between two M-LOK slots in the hero direction, light backdrop, build bcm-16-mid, under cerakote, fitted to references/bcm-mcmr-15-handguard 93b4cf6722f9 (BCM's own close photo of the Flat Dark Earth MCMR-15, region [760,800,960,860], reads #76706e) and 3c44f96c9c21 (BCM's side photo, the face between the slot rows, region [350,676,1100,698], #6d6562); rendered #726b68 for a target of #726b68","family":"cerakote","note":"A grey-brown, far greyer than the polymer of BCM's Flat Dark Earth stock and grip, in all three of BCM's photos. The side photo's reading is a band 22 px high with slot edges in it; a third (a39eb9705499, a band crossing the slots) read #928b83 and was left out. The fitted region in the render is small (2,269 px, a land between two slots)."},"bcm-buffer-anodize":{"label":"BCM buffer, undyed hard anodize","hex":"#d8c5a4","calibration":"appearance","source":"make color-match: the carbine buffer's body, its lit side in the hero direction, light backdrop, build bcm-16-mid drawn apart, under anodized_matte, fitted to references/bcm-carbine-buffer c75e44c92794 (BCM's own photo of the carbine buffer, its body's lit band, region [300,150,950,330], reads #baaa8f); rendered #baaa8f for a target of #baaa8f","family":"anodize","note":"A pale tan with a brushed grain along it, which undyed hard anodize on aluminium comes out as (the Army's drawing of the rifle buffer's body: MIL-A-8625, Type III, Class 1). BCM's H, H2 and H3 buffers are pictured with the same body."},"bcm-buffer-bumper":{"label":"BCM buffer bumper, cream urethane","hex":"#f0e4a2","calibration":"appearance","source":"make color-match: the carbine buffer's bumper, its side in the hero direction, light backdrop, build bcm-16-mid drawn apart, under polymer, fitted to references/bcm-carbine-buffer c75e44c92794 (BCM's own photo, the bumper's side, region [100,170,205,320], reads #cdc38d); rendered #cdc38d for a target of #cdc38d","family":"polymer","note":"A translucent cream-yellow in BCM's photo. Primary Arms' photo of BCM's H buffer has a pale green one: the colour is the urethane's batch, not the weight's."},"bcm-spring-wire":{"label":"BCM action spring, heat-treated wire","hex":"#c69f93","calibration":"appearance","source":"make color-match: the carbine action spring's coils in the hero direction, light backdrop, build bcm-16-mid drawn apart, under steel, fitted to references/bcm-carbine-action-spring f579fe1120ef (BCM's own photo of the spring, every pixel of the wire darker than 200 of 255, reads #7c625b); rendered #7c625a for a target of #7c625b","family":"metal","note":"A bronze brown. A wire a few pixels across in the photo, lit on one side: its reading is of the lit and the shadowed halves together, and so is the render's. Under `steel`, a metal: the colour here is what its reflection is tinted, far lighter than the wire looks."},"bcm-barrel-nut-phosphate":{"label":"BCM G.I. barrel nut, phosphate","hex":"#5b5753","calibration":"appearance","source":"make color-match: the nut's body in the hero direction, light backdrop, drawn apart (exploded), build bcm-16-mid made a drop-in rifle (barrel_nut bcm-gi-barrel-nut, delta_ring bcm-delta-ring-assembly, handguard magpul-moe-mlok-handguard-mid, gas_block bcm-front-sight-base-f-750, handguard_cap bcm-handguard-cap-round-750), under phosphate, region [830,300,970,640], fitted to references/bcm-gi-barrel-nut c43d94b8ae9c (BCM's own photo, the body's lit side under the teeth, region [220,450,600,560], reads #4f4c49; the flange's top [260,380,560,440] reads #4e4c49); rendered #4f4c49 for a target of #4f4c49 (2026-10-28)","family":"metal","note":"BCM's G.I. barrel nut, dry: a matte, mottled dark grey in BCM's one photo of it."},"bcm-cap-phosphate-round":{"label":"BCM handguard cap (round), manganese phosphate","hex":"#b0b1a9","calibration":"appearance","source":"make color-match: the round cap's face in the hero direction, light backdrop, exploded, build bcm-16-mid with the F front sight base and the drop-in parts, under phosphate, fitted to references/bcm-handguard-cap-round-750 6aea7065ddd1 (BCM's one photo of the cap, its face from a little below, the whole cap: tools/color_sample.py reads #6d6e6a); rendered #6c6e6a and #6e6e6a, the fit stepping between #afb1a9 and #b1b1a9, for a target of #6d6e6a","family":"metal","note":"BCM's round handguard cap (.750), dry: a matte, grainy mid grey with a little olive in it in BCM's one photo of it (500 px, on grey), as a manganese phosphate on bare steel often is. Lighter than the triangle cap's photo (#515559, another session's light and exposure): each is fitted to its own."},"bcm-cap-phosphate-triangle":{"label":"BCM handguard cap (triangle), manganese phosphate","hex":"#81888c","calibration":"appearance","source":"make color-match: the triangular cap's face in the hero direction, light backdrop, exploded, build bcm-16-mid with the F front sight base and the drop-in parts, under phosphate, fitted to references/bcm-handguard-cap-triangle-750 f771ddce876e (BCM's one photo of the cap, its face from a little below, the whole cap: tools/color_sample.py reads #515559); rendered #515659 for a target of #515559","family":"metal","note":"BCM's triangular handguard cap (.750), dry: a matte dark grey with a cool cast in BCM's one photo of it (500 x 456, on grey). Darker than the round cap's photo (#6d6e6a): each is fitted to its own."},"bear-creek-fde":{"label":"Bear Creek Flat Dark Earth","hex":"#c4b5a1","calibration":"appearance","source":"make color-match: the BC-15 lower's left side behind the magazine catch in the hero direction, light backdrop, build budget-16, under cerakote with the slot's matte sheen, fitted to Bear Creek's one photo of LR-15FDE (references/bca-stripped-lower de8b7bdc0836, region [545,458,700,492], reads #a39686); rendered #a39686 for a target of #a39686","family":"other","note":"One photo, the only one on Bear Creek's page: there is no second to check it. Its magazine well reads darker in the photo (region [255,400,300,470], #938675) where the app draws the well as light as the rest (#a39686). Bear Creek names the coat two ways (the page's title, Cerakote; the item and its description, a powder coat, \"Frosted Tan\"): a pale grey tan either way."},"cloud-defensive-fde":{"label":"Cloud Defensive FDE","hex":"#745827","calibration":"appearance","source":"make color-match: the REIN's tube in the hero direction, light backdrop, build aero-556-fitted with the light on the handguard's left M-LOK, under anodized_matte, fitted to 3879c02e03b1 (the maker's picture of the FDE REIN from the side, region [712,1040,887,1110], reads #644f32) and c7eaa5c1f126 (the maker's picture from behind, a seller's copy, region [620,830,770,930], reads #6e5939); rendered #695436 for a target of #695436","family":"anodize","note":"A bronze brown, darker and greener than most makers' flat dark earth. Both pictures are one studio's of one light; in the side view the head reads a little darker and yellower (#5e4a29) than the tube."},"cloud-defensive-earth-brown":{"label":"Cloud Defensive Earth Brown","hex":"#693d0d","calibration":"appearance","source":"make color-match: the REIN's tube in the hero direction, light backdrop, build aero-556-fitted with the light on the handguard's left M-LOK, under anodized_matte, fitted to 61d6f2cda4bc (the maker's picture of the Earth Brown REIN from the side, the head, region [1600,1540,1980,1800], reads #563b24) and bc27d295564d (the maker's picture from behind, the tube, region [620,830,770,930], reads #6a492e); rendered #60422d for a target of #604229","family":"anodize","note":"The two pictures are 20 to 30 levels apart (the side view is the darker: its tube reads #4b3019), so the target is between the side view's head and the rear view's tube and each picture is some 10 levels from it. The fit stops 4 levels short in blue: the albedo's blue is nearly spent. A reviewer's photographs of an Earth Brown light outdoors (Inside Safariland) are a brighter orange bronze."},"cloud-defensive-od-green":{"label":"Cloud Defensive OD Green","hex":"#848307","calibration":"appearance","source":"make color-match: the REIN's tube in the hero direction, light backdrop, build aero-556-fitted with the light on the handguard's left M-LOK, under anodized_matte, fitted to 31e88774b0f0 (GRITR Outdoors' picture of the OD Green REIN from the side, region [525,751,676,826], reads #6d6b1b) and 70733e873576 (its picture from behind, region [469,657,563,732], reads #7d7c27); rendered #75742c for a target of #757421","family":"anodize","note":"A bright yellow green, as saturated as the pictures: the fit stops 11 levels short in blue with the albedo's blue spent (the app's light adds a little white to any surface), so it is drawn a touch less saturated than photographed. The two pictures are 12 to 17 levels apart, the rear view the lighter. A colour one seller lists; the maker's own site doesn't, as read."},"daniel-defense-phosphate":{"label":"Daniel Defense heavy phosphate","hex":"#5b5c57","calibration":"appearance","source":"make color-match: daniel-defense-103-barrel's section under the hand guard in the hero direction, light backdrop, exploded, build bcm-16-mid, under phosphate, fitted to references/daniel-defense-103-barrel 0ec43808ddef (the sellers' side view, region [265,620,1830,722], the whole barrel ahead of the flange, reads #494946), 800edcb32507 (their three-quarter view: the thin section [560,380,1000,600] #50504d, the journal [1260,830,1560,1030] #4d4d4b) and 0105c617ad8c (their other three-quarter view: [700,480,1000,640] #575755, [1230,790,1420,900] #4a4a48); rendered #4d4d4a for a target of #4d4d4a (and #4d4e4a on the journal)","family":"metal","note":"The 10.3 in barrel, dry. One series of photos (Primary Arms', as Dirty Bird serves it at 2000 px); its three views are within 14 levels of each other on the thin section and within 3 on the journal, and the target is their mean. Fourteen levels lighter than BCM's barrel in the same seller's series (#3a3a38 to #454545 there, steel-phosphate-charcoal), which is why it has a colour of its own. The maker's own small picture (50c0d40d42c5, 1000 px, retouched) reads #565253 on the journal, lighter and warmer: not used."},"daniel-defense-insert-red":{"label":"Daniel Defense thread insert, red rim","hex":"#933a41","calibration":"appearance","source":"The median of the red pixels (red over green by more than 40) round the clamp screw's insert in Primary Arms' photo of the A1.5 rear sight from behind and to its left (references/daniel-defense-fixed-rear-sight 86d9f645ef0f, the box [1240, 1100, 1380, 1260], 2085 px)","family":"anodize","note":"A ring a few hundredths of an inch across: read off the photo, not fitted with make color-match (the ring is a handful of pixels at the size the page draws a rifle). The fixed front sight's insert is the same red in Primary Arms' photos."},"daniel-defense-tornado-grey":{"label":"Daniel Defense Tornado Grey","hex":"#d3dbea","calibration":"appearance","source":"make color-match: daniel-defense-fixed-rear-sight's left face (the face with the windage drum, below the drum's hole) in the hero direction, light backdrop, build aero-556 with the two sights on its rails, under anodized (matte), fitted to the same face in Evike's photograph of the Tornado Grey set (references/daniel-defense-fixed-front-sight 068da96fe436, as EMG Arms serves it: the rear's marked face left of its markings, region [670,440,790,495], reads #b4bac6); rendered #b4bac6 for a target of #b4bac6","family":"anodize","note":"A light, cool grey. Evike's photos are high key: faces turned more to its light read lighter (the front's right face in the same photo #d2d5da; in the other, 393b7739d245, the rear's right face #d8dbe0 and the front's #ced1d9), and fitted to their mean (#cccfd7) the fit ran to white (#f1f3f3, rendering #cccdcd): brighter than a matte face can be under the app's light, so the face the app's light falls on is fitted, as one face to the same face. The black steel in the same photos (the drum, the screws, #4c4f57 to #505159) reads far lighter than the app draws it (#222223): it reflects the white studio, and isn't an exposure reference. Daniel Defense's sell sheet: \"Type III Hard Coat Anodized (Tornado Gray)\"."},"dead-air-black-cerakote":{"label":"Dead Air Black Cerakote","hex":"#4c4b48","calibration":"appearance","source":"make color-match (job rxd22ti-bronze, black-fit): the tube's upper lit band in the hero direction (camera dir [0.45, 0.3, -1], 9 in off the suppressor), light backdrop, build carbine with the XRF and the RXD22Ti, under cerakote, region [450,410,650,445], fitted to the median of the tube's two lit bands on Midwest Gun Works' photo of RXD22TIBLK from the side (references/dead-air-rxd22ti e5d4c6005c19, regions [1000,650,1200,680] #474644 and [1000,800,1200,830] #414247); rendered #474644 for a target of #474644","family":"cerakote","note":"A charcoal black, the tube's. The band of the photo facing the lens reads #0b0c10, a studio's black reflection on the coat, not the coat."},"dead-air-burnt-bronze-cerakote":{"label":"Dead Air Burnt Bronze Cerakote","hex":"#ab8a66","calibration":"none","source":"Not fitted to Dead Air's photo: the one photograph of THIS product in Burnt Bronze on file is Ruger's of its parts apart (references/dead-air-xrf-brake 7b58ad4e444d), a glossy studio picture whose tube reads #d2a579 in its lit upper band (region [1560,320,1760,345]) and #603e0f to #25170d in the band facing the lens. Fitted to the lit band (make color-match, job rxd22ti-bronze, bronze-fit, the tube's upper band in the hero direction, region [450,410,650,445]) the albedo ran to #f3c58e and the render stopped at #cba579: a highlight no matte surface reaches. The value is the catalog's appearance fit of the same coating by name, Aero's Burnt Bronze Cerakote (data/colors/aero.yaml, aero-burnt-bronze-cerakote, fitted on Aero's photos), which lies between the photo's two bands.","family":"cerakote","note":"The bronze can in American Hunter's pair (2f1167ff33c2) is the RXD30Ti (its band reads RXD3...), and isn't read. A seller's straight photo of RXD22TiBB whole is what a fit wants."},"eotech-tan":{"label":"EOTECH Tan","hex":"#bfae9e","calibration":"appearance","source":"make color-match: eotech-exps3's left flank (the hood's flat) in the hero direction, light backdrop, build v1 with the sight on the receiver's rail, under cerakote, fitted to references/eotech-exps3 de0f9c611881 (Primary Arms EXPS3-0TAN, the left side: regions [780,560,1040,660] and [760,830,1250,960], reads #a09186 and #a29284) and 41e27975b533 (Primary Arms, the right side: [770,275,1265,363], [700,560,880,640] and [680,1000,1000,1080], reads #a7998d, #9d8c7e and #a29283); rendered #a09285 for a target of #a19285","family":"cerakote","note":"The two photos agree within a few levels a channel. A check on the hood's top in the same render reads #a59689 against the right view's upper flank, #a7998d. EOTECH's own 700 px pictures of the tan sight read darker and pinker (#8f796b, #816b5c) in a graded light: looked at for which piece is which colour, and not what this is matched to."},"eotech-tan-polymer":{"label":"EOTECH Tan, moulded housing","hex":"#ad9984","calibration":"appearance","source":"make color-match: eotech-exps3's battery compartment (its left end's flat) in the hero direction, light backdrop, build v1, under polymer, fitted to references/eotech-exps3 de0f9c611881 (Primary Arms EXPS3-0TAN, the left side: region [380,800,680,1000], reads #928272); rendered #928272 for a target of #928272","family":"polymer","note":"One reading, the largest (25,000 px): the same moulding reads lighter where it faces the light (the window's frame from behind, f02c1980f35e [900,650,1300,690]: #9c9384) and darker in the hood's shade (the cap's face in the right view, 41e27975b533 [1628,800,1716,900]: #7d6d60), further apart than ten levels. EOTECH's own pictures have it #90725d beside a hood of #8f796b, a like tone to the hood's and redder."},"eotech-tan-lever":{"label":"EOTECH Tan, quick-detach lever","hex":"#c4b08e","calibration":"appearance","source":"make color-match: eotech-exps3's quick-detach lever (its outer face, at the latch) in the hero direction, light backdrop, build v1, under anodized_matte, fitted to references/eotech-exps3 de0f9c611881 (Primary Arms EXPS3-0TAN, the left side: the lever along the base, region [1100,1195,1700,1260], reads #a29277; its front end [1060,1130,1280,1180], #9f8e72); rendered #a29277 for a target of #a29277","family":"anodize","note":"One photo, of an older sight, in the light the hood's tan is matched in: an olive gold. EOTECH's current pictures have the lever a redder bronze (exps3_tanls: #a07857 beside a hood of #8f796b; the plate of the same metal in exps3_tanrs, #895c3b): another light, and perhaps another anodize. No page on file states its finish; the fit's region is small (3,000 px of the render)."},"eotech-button-grey":{"label":"EOTECH button grey","hex":"#54595f","calibration":"appearance","source":"make color-match: eotech-exps3's down button in the hero direction, light backdrop, build v1, under rubber, fitted to references/eotech-exps3 de0f9c611881 (Primary Arms EXPS3-0TAN, the left side: the two brightness buttons, regions [1315,940,1415,1020] and [1490,940,1600,1020], read #494c51 and #4d5055; the night vision button [1490,715,1570,790], #4a4c51); rendered #4b4e53 for a target of #4b4e53","family":"other","note":"The black sight's buttons read #424244 in Primary Arms' left view of it (29f6391862ba [1330,960,1420,1030]): the same grey within ten levels but for its blue. EOTECH's small pictures have them a bluer charcoal (#323944 on the tan sight). A small flat: 2,000 px of the render."},"eotech-g33-tan":{"label":"EOTECH Tan, G33 tube","hex":"#a18162","calibration":"appearance","source":"make color-match: eotech-g33's foot under the objective tube (its left flat) in the hero direction, light backdrop, build v1 with the G33 behind the EXPS3, under anodized_matte, fitted to references/eotech-g33 3145815589cd (EOTECH-G33-Tan-1, EOTECH's own left side view: the tube at mid-height either side of its mark, regions [540,740,640,900] and [215,740,295,900], reads #89715a and #826b56); rendered #876e58 for a target of #866e58","family":"anodize","note":"A round tube has no flat: the target is the tube's side at mid-height in the picture, and the fit is on the flat of the foot under it, the same metal. The tube's own side in that render reads #947a63, inside what the picture's tube spans from its middle to its lower side (#977f6c). EOTECH's same view as Arisaka Defense serves it (d40b117a7965, another unit) reads #72604d and #6f5c49 there, darker all over by twenty levels: the larger picture, the maker's own address, is taken. No page on file states the bare metal's finish."},"eotech-g33-tan-rubber":{"label":"EOTECH Tan, G33 armour","hex":"#ae926d","calibration":"appearance","source":"make color-match: eotech-g33's armour (its left flat) in the hero direction, light backdrop, build v1 with the G33 behind the EXPS3, under rubber, fitted to references/eotech-g33 3145815589cd (EOTECH-G33-Tan-1, EOTECH's own left side view: the armour's flat, region [730,700,1060,900], reads #917a5d); rendered #917a5d for a target of #917a5d","family":"other","note":"EOTECH's own picture, the larger of two. The same view as Arisaka Defense serves it (d40b117a7965 [640,380,880,520], another unit in a lower light) reads #7a6851: darker by twenty levels, with the same step from the tube to the armour (lighter and yellower). T.REX ARMS' photos of a tan unit on slate (19f580f18851) have the armour an olive grey under their light: not used."},"eotech-g45-tan-rubber":{"label":"EOTECH Tan, G45 armour","hex":"#876a4b","calibration":"appearance","source":"make color-match: eotech-g45's armour (the eight-sided body's left flat) in the hero direction, light backdrop, build v1 with the G45 behind the EXPS3, under rubber, fitted to references/eotech-g45 6fece6de9f55 (EOTECH-G45-Tan-1, EOTECH's own left side view of the tan kit: the armour's side flat, regions [1180,800,1600,860] and [1180,880,1600,1000], reads #6f5841 and #755d45; the collar's side pad [720,800,1020,860], #725b43); rendered #725b44 for a target of #725b43","family":"other","note":"One photo, the maker's own; its three readings of the side flat are within six levels a channel. The same picture's facet above the flat, turned to the light, reads #b3a18c, and the app's does lighter there too. A browner, darker tan than the G33's armour in EOTECH's picture of that kit (#917a5d) beside the same tube (the tube's preset, eotech-g33-tan, renders #8d735c in this picture for the #88725f this kit's tube reads). T.REX ARMS' photo of a tan one on slate (cc40d744d76d) has the armour an olive khaki under its own light: not used."},"expo-arms-fde":{"label":"Expo Arms FDE Cerakote","hex":"#927966","calibration":"appearance","source":"make color-match: the 15 in M-LOK handguard's left side face on the solid block at its rear in the hero direction, light backdrop, build budget-16 (no sight), under cerakote, fitted to Primary Arms' two photos of XP-GUARD15-FDE: the same face in its right view (references/expo-arms-mlok-15-handguard b73e40fcdf82, region [90,712,390,790], reads #7b6756) and its left view (bb47fb7d2cad, region [1780,715,2010,788], reads #7b695c); rendered #7b6859 for a target of #7b6859","family":"cerakote","note":"A dark, brown flat dark earth, as Primary Arms' photos have it (the two agree within 6 levels; the upper face in the right view reads #725f4e)."},"fn-smoke":{"label":"FN smoke (translucent)","hex":"#796862","calibration":"none","source":"The median sRGB of the body seen on white in Midwest Gun Works' photo of the 50-round P90 magazine (references/fn-p90-50-magazine 128e601bf5c7, region [500,760,700,800]), as the translucent finish takes its colour: what the backdrop reads through the body (data/finishes.yaml, translucent_polymer).","family":"other","note":"Photos of it disagree: the same seller's photo reads #6c5d5a a little further along the body, Blackstone's brighter view of the top face #c8b99f (exposed for the white), Wikimedia's loaded one #ab9a82 over the brass inside it. Not fitted under the app's light."},"geissele-ddc":{"label":"Geissele Desert Dirt Color","hex":"#a0887b","calibration":"appearance","source":"make color-match: geissele-mk16-15-handguard's left side face at the clamp block in the hero direction, light backdrop, build bcm-16-mid with this rail (option ddc) and no optic, under anodized, fitted to 25fd311cc861 (Primary Arms' 05-792S_02, the Desert Dirt rail's left side seen level, 2200 x 1467, the side face along its length, regions [140,699,1740,709] and [140,760,1740,772], reads #8b776d and #8b796d) and bce26325b8d2 (Primary Arms' 05-792S_03, the same rail from above and behind, the side face, region [1737,1062,1862,1125], reads #86766f); rendered #8a776e for a target of #89776e","family":"anodize","note":"One rail, one seller's studio. Primary Arms' own page for it says: \"Geissele's Desert Dirt Color (DDC) finish refers to a variety of shades of desert terrain designed to better break up a rifle's outline. These colors can vary drastically even between products from the same batch and are not intended to color match.\" Other sellers' pictures of the colour are a pale peach (AR15Discounts' 15 in rail, 40a9c938a503, #dfbc9a, 700 px) and an olive brown (Bullet Central's short rail, 7c61cabf5c93). Within the photo taken, the light falls off along the rail: the same face reads #a98f7e on the clamp block beside the lens and #766764 at the muzzle end; the target is the middle of its length, which the three-quarter view agrees with. Checked on the upper face: renders #857268 where the three-quarter photo reads #877871. Geissele's maker's own pictures aren't read (its site refuses the reader)."},"geissele-ddc-receiver-set":{"label":"Geissele Desert Dirt Color (Super Duty receiver set)","hex":"#b27b3c","calibration":"appearance","source":"make color-match: geissele-super-duty-stripped-upper's left side flat under the rail, in the hero direction, light backdrop, build bcm-16-mid with this upper (option ddc) and no optic, under anodized, region [700,385,1100,415], fitted to 1bb49287dbc2 (Primary Arms' 05-1171S_04, the DDC set's left side seen level, 2200 x 1467, the upper's side flat under the rail, region [800,290,1450,335], reads #9e7650, 11,997 px); rendered #9e7651 for a target of #9e7650","family":"anodize","note":"The Super Duty Receiver Set's DDC (05-1171S), one colour for its two halves: \"Buying a matched set guarantees consistent color across both halves of your rifle\" (Charlie's Custom Clones). A copper brown in Primary Arms' four photos of the set, where the same studio's DDC MK16 rail reads a grey taupe (geissele-ddc, #8b776d on its side face): Primary Arms says of DDC that its shades 'can vary drastically even between products from the same batch'. The second photo, 493f19023c2c (05-1171S_03, from the rear left above), reads #aa8565 on the same flat (467 px) and #a48165 on the round body below it, where the fitted colour renders #996f44: 11 to 33 levels apart, the photo's light falling across the body from above; the level photo, the larger region, is the target."},"geissele-socket-steel":{"label":"Geissele sling socket steel","hex":"#5a5356","calibration":"none","source":"Read off Primary Arms' photos of the MK16's sling swivel cups (references/geissele-mk16-15-handguard 2b07184f9c79 region [1678,628,1736,640] reads #312628; bce26325b8d2 region [1462,960,1490,985] reads #665a5a; 413379c0fd31 region [1487,931,1512,956] reads #a1a0ae): a middle of the three, with their warm cast.","family":"metal","note":"Not matched, and not fitted: a smooth dark steel cup a quarter of an inch across, whose brightness in a photo is what it reflects (three photos of one cup read from #312628 to #a1a0ae). It is dark steel with a bronze or violet cast on the black rail and on the Desert Dirt one; what it is finished with isn't on a page read."},"geissele-black-oxide":{"label":"Geissele trigger black","hex":"#4c4a4c","calibration":"appearance","source":"make color-match: geissele-ssa-e's hammer, its left flat, in the hero direction, light backdrop, exploded view (the group is inside a receiver otherwise), build bcm-16-mid with this trigger, under steel, fitted to 86bac1cc4a94 (Primary Arms' own photo of the trigger and the hammer lying apart, 2200 x 1467, the hammer's flat, region [1056,209,1199,330], reads #41413f) and 1bf5dd1b0dab (the maker's parts view at BCM, 1100 x 1100, the hammer's flat, region [450,700,620,770], reads #474547); rendered #444344 for a target of #444344","family":"metal","note":"The SSA-E's steel as photographed: sellers call it \"a durable black finish\" (Primary Arms) and one distributor-fed page \"Black Oxide Finish\" (Selway Armory), and on its wire-cut flats it photographs as a matte charcoal, not a black: #41413f to #525252 in Primary Arms' two photos where the same studio's black anodized rail reads #363439 and its black Melonite gas block #282828, and #474547 in the maker's own parts view (lighter still, #6a6665 to #807d7d, in the maker's brightly lit three-quarter view, which wasn't taken). The app's placeholder black under steel renders #1e1e1f. The trigger's body flat renders #413f41 beside the hammer's #444344. The bow's cast surface is glossier and blacker in the photos; it is one piece with the body and drawn with it."},"geissele-buffer-anodize":{"label":"Geissele buffer, pale gold","hex":"#d8cead","calibration":"appearance","source":"by the gain of a fit, not fitted itself: the body is under its spring's coils and their shade in every view the app has of it. BCM's carbine buffer, the same shape under the same finish (anodized_matte) in the same view (make color-match, build bcm-16-mid drawn apart, the hero direction), took its photo's reading #baaa8f to #d8c5a4; the same gain a channel on this one's reading, #bab297 (references/geissele-super-42-h1 bd3cd61e3456, Midwest Gun Works' photo of the set, the buffer's body, region [450,825,700,890])","family":"anodize","note":"One seller's studio. Primary Arms' photos have the body a pale silver-green and two owners' plain silver (Alexander's: \"Color: Silver\"; Midwest Gun Works: \"Finish / Color: Unfinished\"): a clear or lightly dyed anodize whose tone is the light's as much as its own."},"geissele-buffer-bumper":{"label":"Geissele buffer bumper, pale grey","hex":"#d3cfc4","calibration":"appearance","source":"by the gain of a fit, not fitted itself: the bumper is inside its spring in every view. BCM's buffer's bumper, the same shape under the same finish (polymer) in the same view, took its photo's reading #cdc38d to #f0e4a2; the same gain a channel on this one's reading, #b4b1ab (references/geissele-super-42-h1 bd3cd61e3456, the bumper's side, region [738,830,772,885])","family":"polymer","note":"A small region (34 px wide). A fit of it in place ran to white: what shows of it between the coils is in their shade."},"geissele-spring-wire":{"label":"Geissele Super 42 spring, stranded wire","hex":"#948577","calibration":"appearance","source":"make color-match: the Super 42 spring's coils behind its buffer in the hero direction, light backdrop, build bcm-16-mid with the H1 set drawn apart, under steel, fitted to references/geissele-super-42-h1 bd3cd61e3456 (Midwest Gun Works' photo of the set, every pixel of the spring darker than 200 of 255, reads #5c5249); rendered #5c5249 for a target of #5c5249","family":"metal","note":"A dark bronze brown. Strands a few pixels across, lit on one side: the reading is of the lit and the shadowed halves together, and so is the render's."},"geissele-barrel-phosphate":{"label":"Geissele manganese phosphate (barrels)","hex":"#373737","calibration":"appearance","source":"make color-match: geissele-145-chf-barrel's long taper between the collar and the chamber in the hero direction, light backdrop, exploded, build bcm-16-mid with this barrel, under phosphate, fitted to references/geissele-145-chf-barrel dc38f9181866 (Primary Arms' side view, 2200 x 1467, region [100,600,2100,860], the whole barrel, reads #2f2f2f) and 7f3cd09611e9 (its three-quarter view, region [500,440,1100,760], the taper, reads #3e3e3e), with the 13.9 in barrel's two from the same studio between them (references/geissele-139-chf-barrel aaf30d1a864c, side, region [100,600,2100,860], #373737; db8a0e08f1ef, three-quarter, the whole barrel, #323232); rendered #363636 for a target of #363636","family":"metal","note":"Geissele's two cold-hammer-forged barrels, dry, in one seller's studio: four photos from #2f2f2f to #3e3e3e, their mean the target (the two views of one barrel are 15 levels apart, so neither alone is it). About nine levels darker than BCM's barrel in the same studio's same two views (#3a3a38 and #454545, the photos steel-phosphate-charcoal is fitted to): a darker phosphate by these photos, and a colour of its own. In the picture fitted, the journal renders #2f2f2f and the chamber section #363636. Geissele's own pictures aren't read (its site refuses the reader), and sellers' renderings of the barrel (Rooftop Defense's, a pale grey #6f6f78; C. Stephens') aren't photographs of the finish."},"geissele-ddc-lower":{"label":"Geissele Desert Dirt Color (Super Duty lower)","hex":"#b79d86","calibration":"appearance","source":"make color-match (2026-10-28, job gsd-lower/ddc-fit): geissele-super-duty-stripped-lower's left well wall in the hero direction, light backdrop, build bcm-16-mid with this lower (option ddc), under anodized, region [420,600,580,730]; fitted to the mean of Primary Arms' two side photos of 05-2994-S, each the median of a lit flat with its darkest 10% and brightest 15% dropped: references/geissele-super-duty-stripped-lower 940f8244472a (the left side, the face above the trigger, region [300,620,900,850], #988676) and 161ebf431735 (the right side, the well's wall panel, region [1386,780,1870,1040], #a79480): target #a08d7b, rendered #a08c7b. Checked on the left face above the trigger, rendered #a08c7b where the right photo's same face reads #a4917e","family":"anodize","note":"One lower, one seller's studio: a khaki tan, lighter and less red than the same studio's photos of Geissele's 15 in MK16 rail in DDC (geissele-ddc, #a0887b fitted to readings of #86766f to #8b796d). Primary Arms of DDC: \"These colors can vary drastically even between products from the same batch and are not intended to color match\": two parts of one build in DDC are drawn as photographed, not as one colour."},"geissele-ddc-t1-mount":{"label":"Geissele Desert Dirt Color (Super Precision T1 mount)","hex":"#d5a886","calibration":"appearance","source":"make color-match (2026-11-03, job gspm/ddc-fit): geissele-super-precision-micro-absolute's plate's left face in the hero direction, light backdrop, build v1 with this mount (option ddc) and no dot, under anodized, region [560,345,1090,385]; fitted to the mean of Primary Arms' two level photos of the DDC mounts' left sides, each the median of the plate's left face with its darkest 10% and brightest 15% dropped: references/geissele-super-precision-micro-absolute ba687bf5d135 (05-401S, region [700,570,1600,690], #a5856c) and references/geissele-super-precision-micro-lower-13 da3ad1df27ce (05-469S, region [500,300,1450,430], #9e7c63): target #a28067, rendered #a28067","family":"anodize","note":"The three Super Precision T1 mounts' Desert Dirt: a warm tan in Primary Arms' photos of them, where the same studio's DDC MK16 rail is a grey taupe (geissele-ddc, fitted to #89776e): reused, that colour drew these mounts greyer and darker than their photos. The 1.93's DDC photo (c8fa7e8075ca) is of its right side, the side the app's light doesn't fall on: its plate's face reads #8d7058, darker as that side is. Primary Arms of DDC: \"These colors can vary drastically even between products from the same batch and are not intended to color match\"."},"geissele-gray-buffer-tube":{"label":"Geissele gray (buffer tube)","hex":"#8b817f","calibration":"appearance","source":"make color-match (2026-11-03, job graytube/fit-gray): geissele-premium-mil-spec-buffer-tube's rail, its left side face, in the hero direction, light backdrop, drawn apart (exploded=1), build two-tone-16 with the gray assembly in its slots and Geissele's Super 42 H2, under anodized, region [800,578,1150,598]; fitted to references/geissele-premium-mil-spec-buffer-tube 234b20bbfb70 (Geissele's own studio picture of the gray assembly on Charlie's Custom Clones' page, 08-162g_grey_buffer_tube_040621_h1, 1106 x 793), the rail's right side face behind the logo, region [140,410,420,428], #7e7675; rendered #7e7675 for a target of #7e7675. Checked on the tube's round body: renders #7b7372 where the photo's body (region [100,300,580,400]) reads #756f6f","family":"anodize","note":"A warm mid grey, a little red over blue, as every picture of the gray on file has it. It varies from lot to lot: Charlie's own picture of four gray assemblies beside a black one under one light (7564882554c6, \"COMMERCIAL LIGHT (4100K)\") has the four tubes' bodies at #5a5251, #68605b, #89817d and #5a5352 (their rails #5b5351, #635b58, #877f7c, #5e5654), 47 levels apart from the darkest to the lightest, where the black one beside them reads #3d3b3e; Geissele's studio picture fitted here reads between them. Charlie's: \"Black is easy. Gray is hard. Keep in-mind that gray in your mind is different than gray in the head of the next person.\""},"geissele-ddc-buffer-tube":{"label":"Geissele Desert Dirt Color (buffer tube)","hex":"#7d4d2e","calibration":"appearance","source":"make color-match (2026-11-03, job graytube/fit-ddc): geissele-premium-mil-spec-buffer-tube's rail, its left side face, in the hero direction, light backdrop, drawn apart (exploded=1), build two-tone-16 with the DDC tube in its slot, under anodized, region [800,578,1150,598]; fitted to references/geissele-premium-mil-spec-buffer-tube fbfef3f8409d (Primary Arms' 08-162S_00, the DDC tube's right side seen level, 2200 x 1467), the rail's right side face behind the logo, region [450,850,1200,925], #745545; rendered #745546 for a target of #745545. Checked on the tube's round body: renders #71503f where the photo's body (region [300,600,1500,800]) reads #765646","family":"anodize","note":"A copper brown, as Primary Arms' four photos of the DDC tube have it; the same studio's DDC MK16 rail reads a grey taupe (geissele-ddc, #8b776d) and its DDC Super Duty receivers a copper brown (geissele-ddc-receiver-set): Primary Arms of this tube, \"These colors can vary drastically, even between products from the same batch, and are not intended to color match\". Charlie's own pictures of its DDC assembly (3bb361da6107, a yellow tan) aren't fitted: one is lit warm and one is a packaged tube on a cluttered ground (6569f4ecb02e)."},"geissele-laser-mark":{"label":"Geissele laser mark","hex":"#d6d6d3","calibration":"none","source":"Not fitted: the marks' strokes are two or three pixels wide in the app. Read off the photos of the tube's mark: #b2b6b6 on the black (references/geissele-premium-mil-spec-buffer-tube c5f8fd0417ad, the light strokes of GEISSELE), #e5e0de on the gray (234b20bbfb70), #fcfbf7 on the DDC (fbfef3f8409d): a pale grey between them.","family":"metal","note":"Laser marked through the anodize: the aluminium under it, frosted. White in every colourway's photo."},"guntec-anodized-clear":{"label":"Guntec Anodized Clear","hex":"#e7e6e6","calibration":"appearance","source":"make color-match: the tube's side in the hero direction (region [500,420,1250,520]), light backdrop, build bcm-16-mid with Guntec's tube drawn apart, under anodized, fitted to Guntec's own photograph of the tube in this colour (references/guntec-ar15-mil-spec-buffer-tube-gen-2 1b50c33def5f, MILTUBE-G2-CLEAR.jpg, 1500 px, the gallery of the page the user saved 2026-10-19: the top of the tube's body above its highlight, x 300 to 1000, 8 to 70 px under its top line, reads #d2d6ed) through the studio's treatment (the header: the clear made neutral, the white ground on the app's backdrop): #c0c0c0; rendered #c1c0c0 for a target of #c0c0c0","family":"anodize","note":"Clear anodize is the aluminium's own grey under the oxide: the treatment makes it neutral by construction, so its hue is an assumption and its lightness is the photograph's. A pale silver, lighter than batch 12 had it. the2ndtactical's picture of the clear tube (ca79a7f5e6ca) is its copy of this photograph, not a picture recoloured as batch 12 had it. Before: #d2d3d7 (drawn #b0b1b4), from batch 12, on ABC Sportz's photographs of Guntec's clear sets."},"guntec-anodized-red":{"label":"Guntec Anodized Red","hex":"#b52535","calibration":"appearance","source":"make color-match: the tube's side in the hero direction (region [500,420,1250,520]), light backdrop, build bcm-16-mid with Guntec's tube drawn apart, under anodized, fitted to Guntec's own photograph of the tube in this colour (references/guntec-ar15-mil-spec-buffer-tube-gen-2 8b887d2061e1, MILTUBE-G2-RED.jpg, 1500 px, the gallery of the page the user saved 2026-10-19: the top of the tube's body above its highlight, x 300 to 1000, 8 to 70 px under its top line, reads #a93f51) through the studio's treatment (the header: the clear made neutral, the white ground on the app's backdrop): #9a3840; rendered #9a3840 for a target of #9a3840","family":"anodize","note":"A crimson: in Guntec's photograph its blue stands over its green, and it is darker than batch 12's red, which a 600 px copy of another of Guntec's pictures (the red set's) gave. Redcon1's picture of the red set (eabe3e83f28b) reads lighter and pinker, #da4241. Before: #c30707 (drawn #a53030), from batch 12, on The Country Shed's 600 px copy of Guntec's picture of its red set."},"guntec-anodized-gold":{"label":"Guntec Anodized Gold","hex":"#ecb13d","calibration":"appearance","source":"make color-match: the tube's side in the hero direction (region [500,420,1250,520]), light backdrop, build bcm-16-mid with Guntec's tube drawn apart, under anodized, fitted to Guntec's own photograph of the tube in this colour (references/guntec-ar15-mil-spec-buffer-tube-gen-2 4008068fcaac, MILTUBE-G2-GOLD.jpg, 1500 px, the gallery of the page the user saved 2026-10-19: the top of the tube's body above its highlight, x 300 to 1000, 8 to 70 px under its top line, reads #d9a856) through the studio's treatment (the header: the clear made neutral, the white ground on the app's backdrop): #c79744; rendered #c69744 for a target of #c79744","family":"anodize","note":"A warm, orange-leaning gold, a little darker than batch 12's. the2ndtactical's gold picture is its copy of this photograph, not the clear one recoloured as batch 12 had it. Before: #f3c34b (drawn #cba54c), from batch 12, on ABC Sportz's photograph of Guntec's gold set."},"guntec-anodized-blue":{"label":"Guntec Anodized Blue","hex":"#157dcf","calibration":"appearance","source":"make color-match: the tube's side in the hero direction (region [500,420,1250,520]), light backdrop, build bcm-16-mid with Guntec's tube drawn apart, under anodized, fitted to Guntec's own photograph of the tube in this colour (references/guntec-ar15-mil-spec-buffer-tube-gen-2 228062fbd1c9, MILTUBE-G2-BLUE.jpg, 1500 px, the gallery of the page the user saved 2026-10-19: the top of the tube's body above its highlight, x 300 to 1000, 8 to 70 px under its top line, reads #377cd8) through the studio's treatment (the header: the clear made neutral, the white ground on the app's backdrop): #316faf; rendered #336faf for a target of #316faf","family":"anodize","note":"A bright azure in the photograph (#377cd8); with the studio's blue taken out, a plainer, deeper blue. Its red is near the albedo's floor and renders 2 levels over the target. Before: #1677c2 (drawn #336ba4), from the map."},"guntec-anodized-bronze":{"label":"Guntec Anodized Bronze","hex":"#9a644f","calibration":"appearance","source":"make color-match: the tube's side in the hero direction (region [500,420,1250,520]), light backdrop, build bcm-16-mid with Guntec's tube drawn apart, under anodized, fitted to Guntec's own photograph of the tube in this colour (references/guntec-ar15-mil-spec-buffer-tube-gen-2 d97379f956eb, MILTUBE-G2-BRZ.jpg, 1500 px, the gallery of the page the user saved 2026-10-19: the top of the tube's body above its highlight, x 300 to 1000, 8 to 70 px under its top line, reads #926863) through the studio's treatment (the header: the clear made neutral, the white ground on the app's backdrop): #855d4f; rendered #855d4f for a target of #855d4f","family":"anodize","note":"A pinkish copper. Before: #985f46 (drawn #845a49), from the map."},"guntec-anodized-green":{"label":"Guntec Anodized Green","hex":"#66693c","calibration":"appearance","source":"make color-match: the tube's side in the hero direction (region [500,420,1250,520]), light backdrop, build bcm-16-mid with Guntec's tube drawn apart, under anodized, fitted to Guntec's own photograph of the tube in this colour (references/guntec-ar15-mil-spec-buffer-tube-gen-2 ee953cbe1d47, MILTUBE-G2-GREEN.jpg, 1500 px, the gallery of the page the user saved 2026-10-19: the top of the tube's body above its highlight, x 300 to 1000, 8 to 70 px under its top line, reads #686c55) through the studio's treatment (the header: the clear made neutral, the white ground on the app's backdrop): #5f6043; rendered #5e6043 for a target of #5f6043","family":"anodize","note":"An olive drab. the2ndtactical's GT-BT-GREEN ANO is this colour: its picture is its copy of this photograph. Before: #666435 (drawn #5e5d3f), from the map."},"guntec-anodized-grey":{"label":"Guntec Anodized Grey","hex":"#697698","calibration":"appearance","source":"make color-match: the tube's side in the hero direction (region [500,420,1250,520]), light backdrop, build bcm-16-mid with Guntec's tube drawn apart, under anodized, fitted to Guntec's own photograph of the tube in this colour (references/guntec-ar15-mil-spec-buffer-tube-gen-2 6c1fc1488468, MILTUBE-G2-GREY.jpg, 1500 px, the gallery of the page the user saved 2026-10-19: the top of the tube's body above its highlight, x 300 to 1000, 8 to 70 px under its top line, reads #6a77a3) through the studio's treatment (the header: the clear made neutral, the white ground on the app's backdrop): #606a83; rendered #606a83 for a target of #606a83","family":"anodize","note":"A blue grey in the photograph (#6a77a3), a slate grey with the studio's blue out of it. Before: #67728d (drawn #5f677b), from the map."},"guntec-anodized-irish-green":{"label":"Guntec Anodized Irish Green","hex":"#088053","calibration":"appearance","source":"make color-match: the tube's side in the hero direction (region [500,420,1250,520]), light backdrop, build bcm-16-mid with Guntec's tube drawn apart, under anodized, fitted to Guntec's own photograph of the tube in this colour (references/guntec-ar15-mil-spec-buffer-tube-gen-2 f3767d2e2b64, MILTUBE-G2-IG.jpg, 1500 px, the gallery of the page the user saved 2026-10-19: the top of the tube's body above its highlight, x 300 to 1000, 8 to 70 px under its top line, reads #307f66) through the studio's treatment (the header: the clear made neutral, the white ground on the app's backdrop): #2b7151; rendered #307151 for a target of #2b7151","family":"anodize","note":"A bright green with some blue in it. Its red is near the albedo's floor and renders 5 levels over the target. Before: #087c4b (drawn #306e4c), from the map."},"guntec-anodized-orange":{"label":"Guntec Anodized Orange","hex":"#f39b07","calibration":"appearance","source":"make color-match: the tube's side in the hero direction (region [500,420,1250,520]), light backdrop, build bcm-16-mid with Guntec's tube drawn apart, under anodized, fitted to Guntec's own photograph of the tube in this colour (references/guntec-ar15-mil-spec-buffer-tube-gen-2 464464c23705, MILTUBE-G2-ORANGE.jpg, 1500 px, the gallery of the page the user saved 2026-10-19: the top of the tube's body above its highlight, x 300 to 1000, 8 to 70 px under its top line, reads #ef9628) through the studio's treatment (the header: the clear made neutral, the white ground on the app's backdrop): #db861e; rendered #cc8630 for a target of #db861e","family":"anodize","note":"Its red is at the albedo's ceiling and its blue at the floor: it renders 15 levels short in red and 18 over in blue, a little less saturated than the photograph, as no anodize under this finish can be drawn more so. Before: #f39607 (drawn #cc8230), from the map."},"guntec-anodized-pink":{"label":"Guntec Anodized Pink","hex":"#ea3961","calibration":"appearance","source":"make color-match: the tube's side in the hero direction (region [500,420,1250,520]), light backdrop, build bcm-16-mid with Guntec's tube drawn apart, under anodized, fitted to Guntec's own photograph of the tube in this colour (references/guntec-ar15-mil-spec-buffer-tube-gen-2 50623cdc3277, MILTUBE-G2-PINK_2025.jpg, 1500 px, the gallery of the page the user saved 2026-10-19: the top of the tube's body above its highlight, x 300 to 1000, 8 to 70 px under its top line, reads #d74b72) through the studio's treatment (the header: the clear made neutral, the white ground on the app's backdrop): #c5425b; rendered #c5425b for a target of #c5425b","family":"anodize","note":"A hot pink in the photograph; with the studio's blue out of it a deep pink, lighter and bluer than the red (#9a3840 as drawn), as the two photographs are. Before: #e83658 (drawn #c34055), from the map."},"guntec-anodized-purple":{"label":"Guntec Anodized Purple","hex":"#ad07c1","calibration":"appearance","source":"make color-match: the tube's side in the hero direction (region [500,420,1250,520]), light backdrop, build bcm-16-mid with Guntec's tube drawn apart, under anodized, fitted to Guntec's own photograph of the tube in this colour (references/guntec-ar15-mil-spec-buffer-tube-gen-2 54314b70bd49, MILTUBE-G2-PURPLE-1.jpg, 1500 px, the gallery of the page the user saved 2026-10-19: the top of the tube's body above its highlight, x 300 to 1000, 8 to 70 px under its top line, reads #a22cca) through the studio's treatment (the header: the clear made neutral, the white ground on the app's backdrop): #9426a3; rendered #9430a3 for a target of #9426a3","family":"anodize","note":"A violet. Its green is at the albedo's floor and renders 10 levels over the target: drawn a touch less saturated than photographed. Before: #aa07b3 (drawn #923098), from the map."},"guntec-buffer-anodize":{"label":"Guntec buffer, champagne anodize","hex":"#dfd1a7","calibration":"appearance","source":"make color-match: the buffer's body in the hero direction (region [600,380,1000,660]), light backdrop, build bcm-16-mid with Guntec's tube, buffer and spring, drawn apart, under anodized_matte, fitted to Midwest Gun Works' picture of Guntec's carbine buffer sold alone (references/guntec-ar15-carbine-buffer af72b3d271e9, CARBUF.jpg, 1500 px: the body's median over [450,600,1200,830], the darkest 10% and brightest 15% dropped, reads #d0c39e) through the exposure above: #b6ab8a; rendered #b6ab8a for a target of #b6ab8a","family":"anodize","note":"A pale champagne gold, as undyed anodize on aluminium comes out; a little lighter and yellower than BCM's buffer as drawn. The same body in the same seller's picture of the set (657de6718f20) and in Guntec's picture of its purple set (0ab407ab3350, warmer under that studio's light). A first fit on the photograph's reading untreated ran to #f3efc0 and still drew 10 levels dark: a matte surface can't be as bright as a reading on a white ground."},"guntec-buffer-bumper":{"label":"Guntec buffer bumper, white","hex":"#dacfb8","calibration":"appearance","source":"make color-match: the bumper's side in the hero direction (region [1165,420,1225,520]), light backdrop, the same build and shot, under polymer, fitted to Midwest Gun Works' picture (references/guntec-ar15-carbine-buffer af72b3d271e9: the bumper's side, [1255,630,1370,800], reads #d1c6b0) through the exposure above: #b7ae9a; rendered #b7ae9a for a target of #b7ae9a","family":"polymer","note":"A translucent white in the picture, drawn opaque (BCM's bumper is too): less yellow than BCM's cream bumper."},"hexmag-gray":{"label":"Hexmag Gray","hex":"#696f7a","calibration":"appearance","source":"make color-match (2026-11-03, JOB=hexmag in the part's worktree): a whole HEXTURE panel's face on the left side, low in the gripping section, in the hero direction, light backdrop, build two-tone-16 with this magazine in its magazine slot, under polymer (matte), region [850, 612, 900, 652] (1500 px; a second panel, [760, 700, 810, 740], renders the same); rendered #5d6169 for a target of #5d6169, the reading of Blackstone Shooting's photograph of HX30-AR15S2-GRY (references/hexmag-series-2-ar15-30 62f3a85ef619, 1000 x 1000: two magazines, one standing three-quarter from its front left), the left side's plain flat under the lips' block, region [335, 120, 420, 190], reads #5d6169","family":"polymer","note":"A bluish slate grey on Blackstone's photograph. AmmunitionStore's photograph of HX30-AR15S2-GRY (a82d374cd9a2, 741 x 1280, soft, the same pose as Primary Arms' black one) reads #3c413a on the same flat, 33 levels darker and greener; Classic Firearms' small picture (6806412b151e, 722 x 542, the right side) a neutral #7a7a7a. They are three studios' exposures and no photograph has another colour on file beside it to take them into one light, so the sharper, larger file is taken (Blackstone's) and the other two are said here. Classic Firearms calls it \"Dark Gray\"; Hexmag, Blackstone and KYGUNCO \"Gray\"."},"hexmag-fde":{"label":"Hexmag Flat Dark Earth","hex":"#b2a08b","calibration":"appearance","source":"make color-match (2026-11-03, JOB=hexmag in the part's worktree): a whole HEXTURE panel's face on the left side, low in the gripping section, in the hero direction, light backdrop, build two-tone-16 with this magazine in its magazine slot, under polymer (matte), region [850, 612, 900, 652] (1500 px; a second panel, [760, 700, 810, 740], renders the same); rendered #958776 for a target of #958776, the reading of Primary Arms' photograph of HX30-AR15S2-FDE (references/hexmag-series-2-ar15-30 77516244eade, its _00, 5000 x 3334, the left side three-quarter from its front), the left side's plain flat under the catch's window, region [2500, 985, 2740, 1140], reads #958776","family":"polymer","note":"Primary Arms photographs its magazines brightly: its black one reads #6e6e70 on the same flat (8078342f823b), so this may be drawn lighter than the magazine is."},"hexmag-odg":{"label":"Hexmag OD Green","hex":"#6b6a5c","calibration":"appearance","source":"make color-match (2026-11-03, JOB=hexmag in the part's worktree): a whole HEXTURE panel's face on the left side, low in the gripping section, in the hero direction, light backdrop, build two-tone-16 with this magazine in its magazine slot, under polymer (matte), region [850, 612, 900, 652] (1500 px; a second panel, [760, 700, 810, 740], renders the same); rendered #5f5e53 for a target of #5f5e53, the reading of Primary Arms' photograph of HX30-AR15S2-ODG (references/hexmag-series-2-ar15-30 694ac7ddf6cf, its _00, 4860 x 3240, the left side three-quarter from its front), the left side's plain flat under the catch's window, region [2420, 980, 2640, 1130], reads #5f5e53","family":"polymer","note":"Read in the same studio as the FDE one and the black one (see hexmag-fde's note)."},"hexmag-orange":{"label":"Hexmag Orange (HexID follower and latch plate)","hex":"#fe691e","calibration":"none","source":"Primary Arms' photographs of the FDE and the OD Green one, the follower's lit top between the lips: 77516244eade region [2150, 620, 2350, 760] reads #fe7024, 694ac7ddf6cf region [2120, 640, 2320, 760] #fe6119; their mean in linear light","family":"polymer","note":"Not fitted under the app's light: in a rifle the follower is inside the well and the latch plate faces down, so no lit face of either is drawn to fit on (the hero direction sees neither; from below the plate is in the floor's shadow). The photographs' reading is the albedo. On the black one's photograph the follower's top is a highlight (#ffb859, clipped), not taken."},"holosun-fde":{"label":"Holosun FDE","hex":"#c7bf9e","calibration":"appearance","source":"make color-match: holosun-hs510c's hood, its left flat, in the hero direction, light backdrop, build v1 with the sight in the red dot's place, under anodized_matte, fitted to the hood in references/holosun-hs510c 7c65b21ff280 (Impact Guns' right side view of HS510C-FDE, region [1875,188,2275,538], reads #a9a188) and 30ec615c9190 (its left side view, region [200,120,560,300], #a7a086); rendered #a8a187 for a target of #a8a187","family":"anodize","note":"Both photos are one distributor's set (Sportsman's Warehouse's page shows the same photographs): Holosun's own are on a host whose robots.txt can't be read. The housing, the mount and the lever read within 6 levels of the hood in them (#aea78d, #aba38c, #aca58a). In the app the mount's underside flat, turned from the light, renders #989279."},"holosun-fde-tray":{"label":"Holosun FDE, the battery tray","hex":"#d8cfa9","calibration":"appearance","source":"make color-match: fitted on holosun-hs510c's hood, its left flat, in the hero direction, light backdrop, build v1, under anodized_matte (the tray is on the sight's right side, turned from the app's light: the candidate was drawn on the hood's flat, the same finish, in its place), to the battery tray's plate in references/holosun-hs510c 7c65b21ff280 (Impact Guns' right side view of HS510C-FDE, region [1380,1170,1950,1280], reads #bab192) and e1f5fd9249cf (its front right quarter view, region [500,650,760,720], #b2aa8d); rendered #b6ae90 for a target of #b6ae90","family":"anodize","note":"A paler, yellower tan than the housing beside it in the same photos (#a9a188): by 17, 16 and 10 levels straight on, less from the quarter, where the plate is turned from the light. One distributor's photographs."},"holosun-fde-rubber":{"label":"Holosun FDE, the buttons' pad","hex":"#c0b38e","calibration":"appearance","source":"make color-match: holosun-hs510c's buttons' pad, between its two buttons, in the hero direction from 4.5 in, light backdrop, build v1, under rubber, fitted to the pad in references/holosun-hs510c 30ec615c9190 (Impact Guns' left side view of HS510C-FDE): between the buttons (region [490,650,585,770], reads #a1967a) and at its front end (region [300,640,340,760], #9d9274); rendered #9f9477 for a target of #9f9477","family":"other","note":"One photograph, read in two places: it is the only view of the sight's left side on file (Sportsman's Warehouse's is the same picture). A browner tan than the housing round it (#a8a187 in that photo)."},"holosun-solar-cell":{"label":"Holosun solar cell","hex":"#333943","calibration":"none","source":"tools/color_sample.py on Primary Arms' photo of the black HS510C from above and behind (references/holosun-hs510c d6fabf4177a8, region [1110,836,1420,935]: #333943, 13,005 px; a smaller region inside it reads #333944): the cell as that photo has it, through its cover glass.","family":"other","note":"Not fitted under the app's light: the cell lies under a cover glass that mirrors what is over it (Holosun's render has it silver, a photo on a rifle violet), so a photo's reading is the cell and a reflection together, and the one straight studio photo of it is the only reading taken. A dark slate blue."},"huxwrx-black-cerakote":{"label":"HUXWRX Matte Black Cerakote","hex":"#373838","calibration":"appearance","source":"make color-match: huxwrx-flow-556k's smooth body ahead of its grip texture in the hero direction, light backdrop, build bcm-16-mid with the Flash Hider-QD 556, under cerakote, fitted to references/huxwrx-flow-556k f40be2920eba (Primary Arms' HX-2448_01, the black can from the side, region [850,556,1450,620], reads #383838) and 1f585f440d7d (Primary Arms' 2449_02, region [1000,500,1900,580], #404040); rendered #3c3c3c for a target of #3c3c3c","family":"cerakote","note":"The FLOW 556K's black, on 17-4 stainless. One seller's two photos, eight levels apart; the maker's own picture of the black can (in its white paper) is 617 px wide and darker, and isn't read. A charcoal black, not the catalog's stand-in black."},"huxwrx-black-cerakote-ti":{"label":"HUXWRX Matte Black Cerakote (FLOW 556 Ti)","hex":"#676c6e","calibration":"appearance","source":"make color-match: huxwrx-flow-556-ti's smooth body ahead of its grip texture in the hero direction, light backdrop, build bcm-16-mid with the Flash Hider-QD 556, under cerakote, fitted to references/huxwrx-flow-556-ti 09cc4c5b0d02 (HUXWRX's own picture of the black can standing, 2640 x 1980, region [1160,420,1240,980], reads #616567) and cb0c4c6dcac8 (HUXWRX's own of it lying, region [1000,810,1500,890], #5b6061); rendered #5e6264 for a target of #5e6264","family":"cerakote","note":"What the maker calls Matte Black on the titanium can is a graphite grey in both of its own photos, 35 levels lighter than the 556K's black in Primary Arms'; Primary Arms' photo of the Ti (2312c6917350, region [1300,630,1700,700]) reads #4c4d59, darker and bluer, between the two. Fitted to the maker's. Both regions run over the engraved lettering, which darkens them a level or two."},"huxwrx-fde-cerakote":{"label":"HUXWRX Flat Dark Earth Cerakote","hex":"#d2b99c","calibration":"appearance","source":"make color-match: huxwrx-flow-556k's smooth body ahead of its grip texture in the hero direction, light backdrop, build bcm-16-mid with the Flash Hider-QD 556, under cerakote, fitted to references/huxwrx-flow-556k 1964a643ceef (HUXWRX's own picture of the FDE can standing, flow-556k-fde.png, 1800 x 1800, the band under the lock icons, region [730,1005,1080,1040], reads #b6a189); rendered #b6a189 for a target of #b6a189","family":"cerakote","note":"One coating on both cans: the maker's picture of the FLOW 556 Ti in FDE (references/huxwrx-flow-556-ti 3a9c26483816, region [1000,810,1500,890]) reads #b7a179, the same within a level but for a yellower blue channel. The two sellers' photos are far darker and greener and aren't what this is fitted to: Primary Arms' 556K (e38cf2af5cb4, region [940,556,1430,630]) #837956, Mile High's Ti (bb209c7a65ae, region [530,740,600,840]) #87795a; in Primary Arms' series the black can reads #383838, so its exposures are low. The maker's picture is high key (its lit left flank reads #cbb59c): the band facing the lens is the target."},"huxwrx-17-4-heat-tint":{"label":"17-4 stainless, heat tinted","hex":"#8a6a4a","calibration":"none","source":"Read by eye off references/huxwrx-flow-556k 2b9dfd529686 (Primary Arms' 2449_03, the rear end of the black FLOW 556K): the thread and the taper inside the mount, straw to bronze.","family":"metal","note":"Bare, heat-treated 17-4 stainless inside the FLOW 556K's mount. Bright metal: not fitted to a photo (a photo's brightness on it is reflection), and the colour is a reading by eye, between the photo's straw highlights and its brown shadows."},"jp-scs-bumper":{"label":"JP Silent Captured Spring bumper, cream polymer","hex":"#eee4da","calibration":"appearance","source":"make color-match: the Silent Captured Spring's bumper, its lit upper side in the hero direction, light backdrop, build bcm-16-mid with the unit in the buffer's slot drawn apart, under polymer, fitted to references/jp-silent-captured-spring-gen2 3431b2d79bca (MidwayUSA 767861, the standard unit square to its side on white, 2200 x 1650: the bumper's lit upper band, region [150,700,330,760], reads #c7beb6); rendered #c7beb6 for a target of #c7beb6","family":"polymer","note":"One seller's studio. The bumper's lower band in the same photo reads #bfb5ad, lit by the studio's fill, where the render's reads #aba39c. Primary Arms' photo of the standard (0b290578345a) has it a pale green cream (region [1620,590,1790,640] reads #dbe0c3, [1620,690,1790,760] #c2c7a2), and Wing Tactical's photos a yellower urethane: the polymer's batch and the light, as BCM's bumpers are cream in one seller's photo and green in another's."},"jp-scs-tungsten":{"label":"JP Silent Captured Spring tungsten weight","hex":"#91919d","calibration":"appearance","source":"make color-match: the H2's middle tungsten weight, its lit upper side in the hero direction, light backdrop, build bcm-16-mid with jp-silent-captured-spring-gen2-h2 in the buffer's slot drawn apart, under steel, fitted to references/jp-silent-captured-spring-gen2-h2 708eab533a4c (Primary Arms' JPSCS2-15H2_01, the H2 from ahead of its front face, 2200 x 1467: the middle tungsten weight's lit band, region [1560,860,1700,940], reads #7c7c87; [1700,920,1820,990] #787882 and [1450,820,1540,900] #7d7d88 on the same weights); rendered #7c7c87 for a target of #7c7c87","family":"metal","note":"A matte cool grey, ground tungsten, against the bright steel weight beside it. One seller's studio; JP's own small pictures (c5a3ef37c597) have the tungsten weights a darker grey."},"jp-scs-hard-anodize":{"label":"JP Silent Captured Spring slider, dark hard anodize","hex":"#686569","calibration":"appearance","source":"make color-match: the H2's flange, its front face beside the bore, the camera ahead of the unit and to its left (dir [1, 0.3, -0.45], 7 in), light backdrop, build bcm-16-mid with jp-silent-captured-spring-gen2-h2 in the buffer's slot drawn apart, under anodized, fitted to references/jp-silent-captured-spring-gen2-h2 708eab533a4c (Primary Arms' JPSCS2-15H2_01: the flange's front face, region [1870,1000,1960,1080], reads #5d5b5e); rendered #5d5b5e for a target of #5d5b5e","family":"anodize","note":"The H2's slider in Primary Arms' photo, a dark grey: JP's \"clear coat hard anodize\" (the text layer of its selection guide). The same studio's photo of the standard (0b290578345a) and MidwayUSA's have the standard's black; JP's own pictures have the slider a dark bronze. The anodize's tone is the lot's."},"law-tactical-fde":{"label":"Law Tactical FDE","hex":"#897255","calibration":"appearance","source":"make color-match (2026-10-18): the adapter's ring on the rifle's left in the hero direction, light backdrop, build bcm-16-mid with the adapter, under cerakote, region [850,290,990,410], fitted to Midwest Gun Works' photo of the FDE Gen 3-M on white (references/law-tactical-gen3m-folder 93ed44e08726, LTGEN3MFDE.jpg, 1500 px): the stock half's right side, a lit flat beside the logo, region [300,560,340,640], reads #786650; rendered #786650 for a target of #786650","family":"cerakote","note":"A brown tan, flat; the same side further back, in the photo's shade, reads #5f4f3e. T.REX Arms' photos of the same colour are on a slate table under a cool light and read grey-green (#c1c7b5 on a lit top): not used. One photo of one light."},"magpul-d60-window":{"label":"Magpul D-60 window (translucent)","hex":"#f9f9fc","calibration":"none","source":"tools/color_sample.py on Primary Arms' photo of the empty MAG576-BLK from the rear (references/magpul-pmag-d-60 7c86158366b8, 2200 px): the window between its numerals, region [1060,720,1130,800], reads #49484c where the body beside it reads #4b4a4d ([1250,900,1400,1050]); the first over the second, channel by channel as light, is 0.95, 0.95, 0.97, written as a colour. Magpul's own close-up of a loaded one (0528d1bd6412, 700 px) has the window #686565 between two rounds ([320,254,378,264]) and #e8d4aa over a round's brass ([330,236,372,250]).","family":"polymer","note":"Not fitted, and an estimate: the app's see-through plastic takes its colour as what passes through it, and no photo on file shows a backdrop through this window. What is written is how the window reads against the black body round it in Primary Arms' photo of the empty magazine, taking the drum's inside behind it to be as dark as its skin: nearly clear, a touch cool. That agrees with Magpul's close-up, where a round's brass behind it is pale and bright (brighter than the bare brass of the round at the feed lips in Magpul's gallery picture, 7f0070dd0758, the two pictures being lit apart). `make color-match` fits an albedo and is not used on glass or a see-through plastic. Written first as the window's own reading (#49484c), it drew the pane as a black slot in the cover, darker than the body, which the photo doesn't show (2026-10-06)."},"magpul-mcb":{"label":"Magpul Modified Coyote Brown","hex":"#937440","calibration":"appearance","source":"make color-match: the CTR's lock-housing flat in the hero direction, light backdrop, build bcm-16-mid with the CTR, under polymer (satin), fitted to Magpul's own gallery shots of MAG310-MCB: references/magpul-ctr 1be9f7137eaa (shot 02.1, region [640,560,900,650], reads #7b633f) and eeca9d25060e (shot 01.1, region [450,300,880,380], reads #9d8667, a lit top face), each taken into the app's light through the same shots of the black, FDE and ODG stocks (02.1: 1a2c2fe62b86 #313131, 836d56bf6714 #756454, 4878f290ac06 #37372d; 01.1: 35ed6a48fbdb #5d5d5d, 687d6ca56a00 #978676, a228d9c46596 #5b5b51) against the app's renders of those colours on the same flat (#2b2b2b, #73624d, #40392f): #78613e and #776141; rendered #78613f for a target of #78613f","family":"polymer","note":"Set 02.1 is nearly the app's own light (gain 0.95, no offset: its FDE comes out #726252 against the app's #73624d), so the target is close to that photo's own reading; set 01.1 is a brightly lit top face (gain 0.66) and agrees within two levels. Stealth Gray is left out of the map: on the lit top face of 01.1 it reads as light as FDE (#86878c), and with it that set gives #68563c. ODG maps 9 to 14 levels greener and darker than the app renders it (the ODG preset was matched on a rifle photo that has it browner): read this colour as within about 5 levels. Checked on the MVG's own gallery shots 02.1 (references/magpul-mlok-mvg faea18f842f0 black #3e3d3c, 51b6cc71ed5d FDE #7d6c5c, 2431e1ac8dca ODG #424238, 8a14d897e102 MCB #836c4a, region [500,250,700,340]): through the same three colours its MCB comes to #7c6540, and the app draws the MVG's side in this preset #7c6440."},"magpul-mct":{"label":"Magpul Medium Coyote Tan","hex":"#926b50","calibration":"appearance","source":"make color-match: the PMAG 30 GEN M3's upper middle side panel in the hero direction, light backdrop, build bcm-16-mid, under polymer (matte), fitted to Magpul's own gallery shots of MAG557-MCT: references/magpul-pmag-30-gen-m3 5a6d8a51f7b8 (shot 02, region [440,290,610,440], reads #8e6f5d) and 3affd5f92a4f (shot 01, region [450,320,630,470], reads #846857), each taken into the app's light through the same shots of the black and Modified Coyote Brown magazines (02: 3eded591002b #3e3e40, 1969c99feb7c #897253; 01: e78b0eeb0333 #393939, dc82d785ba53 #8a7354) against the app's renders of those two on the same panel (#2c2c2c, #7d6541): #82624f and #765b4a; rendered #7c5f4c for a target of #7c5f4c","family":"polymer","note":"The two sets differ by 12 levels in red after the map (the tan is pinker in shot 02, darker in shot 01): the target is their mean, and either is as likely. Only two colours anchor this map (they leave at most 0.010 in linear light between them), and the one colour left to check it is ODG, which it puts at #333327 where the app renders #423b31 (the ODG preset is browner than Magpul's gallery has it). Primary Arms' own photo of MAG557-MCT (34b24968b02d) reads far lighter and greyer, #a38d7e on white, and wasn't used: a small magazine in a high-key picture. Sold only on the PMAG among the parts on file."},"magpul-stealth-gray-moe-mlok":{"label":"Magpul Stealth Gray (as the MOE M-LOK hand guards' own photos have it)","hex":"#5c5b62","calibration":"appearance","source":"make color-match (2026-10-28, JOB=moe-mid): the MOE M-LOK mid-length's upper side flat above its slots in the hero direction, light backdrop, build bcm-16-mid with the drop-in parts, under polymer (satin), fitted to Magpul's own gallery shots of the two hand guards in their four colours (each set one render recoloured: their edges correlate 0.74 to 0.99), each set taken into the app's light by a gain and offset in linear light fitted on its black, Flat Dark Earth and OD green shots against the app's renders of magpul-black, magpul-fde and magpul-odg on the same flat (#323232, #7d6b55, #474037). MAG426: set 01 (references/magpul-moe-mlok-handguard-mid 07350227f7db, b6a0330a8c69, 60dc2d9c87c2, c2c6b8e46059; the side above the slots #4a4a4a, #a18e79, #6d6459, gray #807f85; the band beside them #454547, #9e8a75, #685e53, gray #7a797f) gives #5f5e63 and #5d5c61; set 03 (2810c81def7a, 7987a54ab75f, 4137006b88cc, 32f412d17d79, above the second slot: #646264, #b29f92, #827968, gray #8e8d93) gives #5a595f; their mean #5d5c61. MAG424: its set (references/magpul-moe-mlok-handguard-carbine 301b76a556b9, 4378fe364781, 029db15b2b70, ebf5bc6f3e4d; above the slots #615f5f, #b8a28a, #726759, gray #85858a; the lower band #545252, #b09981, #64594b, gray #79797e) gives #555559 and #535357, mean #545458. Target the two products' means averaged, #59585d; rendered #59585d","family":"polymer","note":"Magpul's own name for it on both hand guards' pages is Stealth Gray, the K2+'s and the MOE SL's colour (`magpul-stealth-gray`). On the same flat the app draws that preset #505053: the hand guards' photos read 4 to 15 levels lighter (the carbine's 4 to 6, within the maps' own scatter of about 5 levels; the mid-length's 10 to 15, beyond it), and the two lengths' pictures differ from each other by about 9. Which is the colour as moulded isn't settled by renders: the K2+'s catalog shots put it darker, these lighter, and the CTR's top face (magpul-mcb's note) as light as FDE. Drawn as the two hand guards' photos have it together: one colour for one product line, as Magpul names it."},"mas-defense-stealth-gray":{"label":"MAS Defense Stealth Gray Cerakote","hex":"#68717e","calibration":"appearance","source":"make color-match: the 15 in NERO's left side flat between its upper openings and its M-LOK row in the hero direction, light backdrop, build bcm-16-mid with this handguard, under cerakote, fitted to MAS Defense's own pictures of the 15 in in Stealth Gray: its product picture (references/mas-defense-nero-15-handguard 93522d896a7b, MAS00106384-2, the side flat beside the logo, region [100,86,126,110], reads #5c656e) and its Stealth Gray builder set's two level side pictures (6bf562718703, region [276,242,294,270], #555a63; 0627ae73f200, region [480,245,500,270], #5f656f), averaged: #5b616b; rendered #5b616b for a target of #5b616b (region [560,490,860,545], 12375 px)","family":"cerakote","note":"A bluish slate grey, as MAS's pictures have it: the three agree within 11 levels a channel (the builder set's right side the darkest). The pictures are small (800 x 600) and the regions small (127 to 168 px each); MAS's product pictures may be renders. Beside Magpul's Stealth Gray (magpul-stealth-gray, #4e4f53) it is lighter and bluer; it is near Aero's Sniper Grey Cerakote (#676b6a) in lightness and bluer than it."},"mas-defense-fde":{"label":"MAS Defense Flat Dark Earth","hex":"#726851","calibration":"appearance","source":"make color-match: the 15 in NERO's left side flat between its upper openings and its M-LOK row in the hero direction, light backdrop, build bcm-16-mid with this handguard in FDE, under cerakote, fitted to MAS Defense's picture of the 15 in in FDE (references/mas-defense-nero-15-handguard 7668d5d355e9, MAS00106364-2, the side flat beside the logo, region [100,86,126,110], reads #625b4a); rendered #625b4a for a target of #625b4a (region [560,490,860,545])","family":"cerakote","note":"One picture (MAS's pose for every colour), a small region (172 px); MAS's FDE page names no finish: drawn as Cerakote, as its weights are the Cerakoted colours'."},"mas-defense-od-green":{"label":"MAS Defense OD Green Cerakote","hex":"#647860","calibration":"appearance","source":"make color-match: the 15 in NERO's left side flat between its upper openings and its M-LOK row in the hero direction, light backdrop, build bcm-16-mid with this handguard in OD Green, under cerakote, fitted to MAS Defense's picture of the 15 in in OD Green (references/mas-defense-nero-15-handguard a44ca945fae5, MAS00106214-ODGB-2, the side flat beside the logo, region [100,86,126,110], reads #586755); rendered #586755 for a target of #586755 (region [560,490,860,545])","family":"cerakote","note":"One picture (MAS's pose for every colour), a small region (181 px)."},"mas-defense-navy-blue":{"label":"MAS Defense Navy Blue Cerakote","hex":"#5376f3","calibration":"appearance","source":"make color-match: the 15 in NERO's left side flat between its upper openings and its M-LOK row in the hero direction, light backdrop, build bcm-16-mid with this handguard in Navy Blue, under cerakote, fitted to MAS Defense's picture of the 15 in in Navy Blue (references/mas-defense-nero-15-handguard ddd045fa04d5, MAS00106214-BLU-2, the side flat beside the logo, region [100,86,126,110], reads #4c65d8); rendered #4c65c8 for a target of #4c65d8 (region [560,490,860,545]): the blue 16 levels short, more saturated than a matte surface reaches under the app's light","family":"cerakote","note":"A bright royal blue in MAS's picture, far brighter than its name; one picture, a small region (165 px). The fit stops 16 levels short in blue."},"midwest-fde-cerakote":{"label":"Midwest Industries Magpul FDE Cerakote","hex":"#d2c0a0","calibration":"appearance","source":"make color-match: the Combat Rail's side face ahead of its last slot in the hero direction, light backdrop, build aero-556 with this handguard, under cerakote, fitted to references/midwest-combat-rail-15-handguard 4bd57bb451ec (the maker's photo of the Flat Dark Earth 15 in Combat Rail, MI-CRM15-FDE-2, 1200 x 329): its side face between two slots, region [520,150,560,165], reads #b2a289, and at the muzzle end, region [880,95,930,110], #ab9b82; rendered #ae9f86 for a target of #af9f86","family":"cerakote","note":"The maker: \"Custom Cerakote Magpul FDE\". A warm tan, matte. One photograph, the maker's own and 1200 px wide: the only picture of this colour of this handguard on file, so nothing checks it against a second. Checked within it on the face above: the upper face renders #9d8f78 where the photo reads #a29278 (region [600,108,640,118]). The fitted region in the render is small (759 px, the side face's tip)."},"mft-scorched-dark-earth":{"label":"MFT Scorched Dark Earth","hex":"#9a8f6d","calibration":"appearance","source":"make color-match: the stock's housing, its lit upper side in the hero direction, light backdrop, build bcm-16-mid with this stock, under polymer (satin), fitted to references/mft-battlelink-minimalist-stock 45347093555f (Mission First Tactical's picture, region [300, 130, 1400, 190], reads #8b836c) and fbf2137f0dc7 (the same series, region [300, 110, 1400, 180], #8f8469); rendered #8d846b for a target of #8d846b","family":"polymer","note":"The two pictures agree within 4 levels a channel on the lit upper side, and their mean is the target. The panel under the ridge, turned from the light, reads #6b654f and #85795e in the two and renders #645d48. Wing Tactical's own photographs of the earth stock are paler (a seller's light); a buyer on Primary Arms' page calls it 'True coyote brown'."},"olight-desert-tan":{"label":"Olight Desert Tan","hex":"#83613e","calibration":"appearance","source":"make color-match (job olight-baldr-look, rifle-tan): the Baldr S BL's body side in the hero direction, light backdrop, build aero-16-light with the light on the handguard's front rail block, under anodized_matte, region [700,470,900,560], fitted to the reading of a lit flat in AR15Discounts' photograph of the desert tan light from its +z side (references/olight-baldr-s-bl 7b0dbbc5cfe8, the body's side under the clamp, [1050,640,1500,790], #715841; the paddle's side, [1450,860,1650,1000], reads #735942); rendered #715841 for a target of #715841","family":"anodize","note":"A brown tan, darker than SureFire's: Olight's own words for it are \"Desert Tan\" on Blackstone's page (\"Olight BALDR S BL, Weapon Light, Blue Laser, 800 Lumens, Desert Tan\") and \"desert-tan\" in AR15Discounts' markup. The swing arm, its knob, the insert and the bezel's ring are black on the tan light."},"otter-creek-black-cerakote":{"label":"Otter Creek Black","hex":"#454445","calibration":"appearance","source":"make color-match: otter-creek-polonium-k's body, the band of the can that faces the light in the hero direction (region [650,400,1150,520]), light backdrop, build bcm-16-mid with the K on its muzzle, under cerakote, fitted to the lit side of the can in references/otter-creek-polonium-k 0817f888c9c7 (Silencer Central, the K from the side: region [430,300,560,620], reads #484848), 695e8c80ec35 (Capitol Armory, the K lying on its side: [500,470,780,600], #403e41) and 1f7b0cdc9250 (Silencer Shop: [520,400,620,700], #414141); rendered #454445 for a target of #454445","family":"cerakote","note":"A matte charcoal, not a black: the sellers' \"Cerakote\", \"Black\". The three photos of the K agree within eight levels, and two of the Polonium read the same (references/otter-creek-polonium f243e92704d5, Bauer Precision: #484848; e5f6d6d4781b, Capitol Armory: #49474a). Silencer Shop's photo of the Polonium is lit far brighter (#696868) and isn't in the target. A round can has no flat: the fit is on the band that faces the light."},"otter-creek-fde-cerakote":{"label":"Otter Creek Flat Dark Earth","hex":"#b9aa83","calibration":"appearance","source":"make color-match: otter-creek-polonium-k's body in its flat dark earth option, the band of the can that faces the light in the hero direction (region [650,400,1150,520]), light backdrop, build bcm-16-mid with the K on its muzzle, under cerakote, fitted to references/otter-creek-polonium 2352f4807f8d (Blackstone Shooting, the flat dark earth Polonium standing, 2000 x 2000, serial G2521: regions [800,800,1000,1350] and [1000,800,1150,1350], read #9f9373 and #a39276); rendered #a19474 for a target of #a19374","family":"cerakote","note":"The sellers' \"Flat Dark Earth\"; no Cerakote number on any page. One photo's reading, the largest and the most evenly lit, and of the sibling (one maker's colour on both cans). The others on file are lighter and don't agree with it within ten levels: references/otter-creek-polonium 14aebeaf065e (2000 x 2000, #b3a884) and a7b1407b3473 (Bauer Precision, 800 x 800, #b09169); Bauer's photo of the flat dark earth K (references/otter-creek-polonium-k 11ce8a4d4446) is lit from above, #c1aa8c on its upper half and #77654e on its lower; Blackstone's small picture of the K (3e36ba884614, 170 x 510) reads #99886a, beside this target."},"precision-armament-crcn-black":{"label":"Precision Armament black CrCN","hex":"#1d1e20","calibration":"none","source":"Not fitted to a photo: the hex is the catalog's placeholder black (data/finishes.yaml, `placeholder-black`), under the `nitride` finish.","family":"metal","note":"Not matched, and not to be: the maker's \"Ionbond® high temperature CrCN coating (matte black)\" (https://precisionarmament.com/m4-72-severe-duty-compensator/) is a hard black film on stainless, and what a photo reads on it is the studio's light: the maker's straight photo of the black M4-72 (references/precision-armament-m4-72 a1a4c479327e) reads #363435 on its narrow flat square to the lens and #373433 on the base's flats (tools/color_sample.py), its three-quarter photo (1e2ffa21d003) #6d6b6d on the same flat where the light lies along it: the reading follows the light, not the coat. The catalog has no finish type for a PVD coat; it is drawn as the nearest it has, a smooth black on steel (`nitride`), as SureFire's DLC is (surefire-dlc-black)."},"precision-armament-matte-stainless":{"label":"Precision Armament matte stainless","hex":"#cac4bf","calibration":"appearance","source":"make color-match (job pa-stainless): precision-armament-m4-72's left side in the hero direction, light backdrop, build bcm-16-mid with the device in its stainless option, under steel, fitted to the narrow flat of the maker's photo of the stainless device (references/precision-armament-m4-72 4edb633eb80e, region [480,200,580,640], the darkest 10% and brightest 15% dropped, median #a49f9a); rendered #a49f9b on the wrench flat facing the camera (region [1160,400,1190,560]); the body behind the ports, curved and further round from the light, renders #817c78.","family":"metal","note":"The maker's \"Matte Stainless\", \"in-the-white (satin grey)\" (https://precisionarmament.com/m4-72-severe-duty-compensator/): bare 416 stainless with a matte blast, a flat warm grey with no bright line in the maker's two photos and Dirty Bird's, so it is fitted like a paint under the app's matte steel, as Superlative's matte block is, and not drawn as the `stainless` finish's polish."},"primary-arms-fde":{"label":"Primary Arms flat dark earth","hex":"#dfc8b9","calibration":"appearance","source":"make color-match, 2026-10-13: the SLx 1-6x24 Gen IV's illumination knob, the face of its battery cap, in the hero direction (light backdrop, build carbine with the scope in flat dark earth in the ALPHA-MSR's rings), under anodized_matte, fitted to the same face, turned to the lens, in Primary Arms' two photos of PA-SLX-1-6X24S-NOVA-FDE that show it: references/primary-arms-slx-1-6x24-gen-iv 79813964dc56 (from the front left, region [990,836,1144,990], reads #b29f92) and f0400992d947 (from the rear left, region [500,640,620,790], reads #bba69b), their mean #b6a397; rendered #b6a397 for a target of #b6a397. In the same render the eyepiece's flank reads #bdaa9e and the main tube #c1ada1.","family":"anodize","note":"Primary Arms: \"Flat Dark Earth anodized finish\". The photos are lit hard from above: the same scope's upper flanks read #d6beb0 to #e1cec0 in them and its shaded tube #8f7565 to #a08574, where the app's softer light draws both within a few levels of the cap's face. Fitted on the one flat that faces the lens in the photos and in the app's hero view alike; two photos of it agree within 9 levels a channel."},"radian-fde":{"label":"Radian Flat Dark Earth","hex":"#b79978","calibration":"appearance","source":"make color-match: radian-raptor-charging-handle's latch (the left latch's tip, the face turned to the camera) in the hero direction, light backdrop, build aero-556, under anodized_matte, fitted to references/radian-raptor-charging-handle a377e63e9478 (Primary Arms' R0003 from above, region [860,200,940,320], reads #978067) and be03be9599ff (Wing Tactical's, region [895,235,955,270], #ac9a89); rendered #988067 for a target of #978067","family":"anodize","note":"The two photos are 21 to 34 levels apart, Wing Tactical's the lighter and greyer as all of its photos of this handle are: the target is Primary Arms' alone, the larger photo and one of a series under one light (black, Flat Dark Earth, Radian OD, red, NP3)."},"radian-od":{"label":"Radian OD","hex":"#706b53","calibration":"appearance","source":"make color-match: radian-raptor-charging-handle's latch (the left latch's tip, the face turned to the camera) in the hero direction, light backdrop, build aero-556, under anodized_matte, fitted to references/radian-raptor-charging-handle cbbddafd5a8d (Primary Arms' R0375, two latch flats, regions [650,105,720,145] and [455,305,500,365], read #605d4b and #615e4d) and 6c91617182ca (Wing Tactical's, region [315,205,355,232], #818471); rendered #615d4c for a target of #605d4c","family":"anodize","note":"Wing Tactical's photo reads 33 to 39 levels lighter: the target is Primary Arms' alone (the larger photo, its two flats within 2 levels of each other)."},"radian-brown":{"label":"Radian Brown","hex":"#a59173","calibration":"appearance","source":"make color-match: radian-raptor-charging-handle's latch (the left latch's tip, the face turned to the camera) in the hero direction, light backdrop, build aero-556, under anodized_matte, fitted to references/radian-raptor-charging-handle 7df26ac0a6fd (the distributor's RWR0004_1_HR as AR15Discounts hosts it, region [62,990,102,1070], reads #8a7a63) and 8ec94730edea (Wing Tactical's close-up, region [380,222,520,246], #9d836b); rendered #8a7a63 for a target of #8a7a63","family":"anodize","note":"Wing Tactical's close-up reads 8 to 19 levels lighter and redder: the target is the distributor's alone, the larger photo and of one set-up with the Tungsten Grey's. Against Primary Arms' Flat Dark Earth it is the darker and greyer of the two by these photos, which are two sellers' and not one light: the two colours' order rests on Wing Tactical's six side by side, where the brown is the darker."},"radian-tungsten-grey":{"label":"Radian Tungsten Grey","hex":"#969185","calibration":"appearance","source":"make color-match: radian-raptor-charging-handle's latch (the left latch's tip, the face turned to the camera) in the hero direction, light backdrop, build aero-556, under anodized_matte, fitted to references/radian-raptor-charging-handle b7e2da884fd4 (AR15Discounts' picture of its tungsten variant, region [65,1000,105,1080], reads #7e7a70) and 452cf1c7f865 (Wing Tactical's, region [720,955,900,985], #8f8e8a); rendered #7e7a70 for a target of #7e7a70","family":"anodize","note":"Wing Tactical's photo reads 17 to 26 levels lighter and more neutral: the target is AR15Discounts' alone, the larger photo, of one set-up with the Radian Brown's."},"radian-grey":{"label":"Radian Grey","hex":"#676766","calibration":"appearance","source":"make color-match: radian-raptor-charging-handle's latch (the left latch's tip, the face turned to the camera) in the hero direction, light backdrop, build aero-556, under anodized_matte, fitted to references/radian-raptor-charging-handle 63faf9339b17 (Radian's artwork of R0560 as Alexander's hosts it, region [345,265,385,330], reads #60605f) and 05127e5dcddd (Wing Tactical's, region [300,215,350,240], #545454); rendered #5a5a59 for a target of #5a5a59","family":"anodize","note":"The two readings are 11 to 12 levels apart and are averaged (#5a5a59). A dark charcoal a little lighter than the black body: in the artwork the black one's latch reads #373a42 where this one's reads #60605f, the plates the same in both."},"radian-red":{"label":"Radian Competition Red","hex":"#ce393b","calibration":"appearance","source":"make color-match: radian-raptor-charging-handle's latch (the left latch's tip, the face turned to the camera) in the hero direction, light backdrop, build aero-556, under anodized_matte, fitted to references/radian-raptor-charging-handle e4d8d119a9e9 (Primary Arms' R0232 from ahead of its left and above, a latch's top face, region [240,262,340,300], reads #aa3b3c) and 73a9fdb625ea (its photo from above, the latch lit square on, region [850,170,940,290], #e92223); rendered #aa3b3c for a target of #aa3b3c","family":"anodize","note":"A dyed anodize over a blasted face: #e92223 where the light is square on it (the photo from above, the larger reading) and #aa3b3c on a face turned away (the photo from ahead of the left, which is how the app's hero direction sees a latch). Fitted to the second: at the first the fit ran out of red (an albedo of #f30809 rendered #c82727), and a colour that saturated is no colour. AR15Discounts' small picture of the red beside the blue has it #b7493d. Seen from above in the app it is brighter than the target, as the real one is."},"radian-blue":{"label":"Radian Competition Blue","hex":"#077fe7","calibration":"appearance","source":"make color-match: radian-raptor-charging-handle's latch (the left latch's tip, the face turned to the camera) in the hero direction, light backdrop, build aero-556, under anodized_matte, fitted to references/radian-raptor-charging-handle ae3fbd5da54d (AR15Discounts' picture of the red and the blue side by side, 1200 x 1024, region [690,48,745,72], reads #036cbe); rendered #276cbe for a target of #036cbe","family":"anodize","note":"One photo, and a small one (435 pixels read): the only photo of the blue on file large enough to read. Its red channel isn't reached (the render's sheen adds a little light of every colour to a saturated blue): green and blue are. The red handle beside it in the same picture reads #b7493d, between Primary Arms' two readings of the red."},"radian-np3":{"label":"Radian NP3 (nickel-Teflon)","hex":"#ac9f94","calibration":"appearance","source":"make color-match: radian-raptor-charging-handle's latch (the left latch's tip, the face turned to the camera) in the hero direction, light backdrop, build aero-556, under nickel, fitted to references/radian-raptor-charging-handle 8cb9503d18b6 (Primary Arms' R0005 from above: the plate, region [1000,120,1200,250], reads #857b76, and a latch, [680,140,790,250], #7e746b, averaged #82786f); rendered #82786f for a target of #82786f","family":"metal","note":"A metal's face (electroless nickel with Teflon, drawn as `nickel`), which is not usually fitted: a photo's brightness on bright metal is what it reflects. This coat is matte and evenly lit in Primary Arms' photo, with no highlight in either region, and the photo's own reading written as the colour drew it far too dark (#625a53 for the photo's #82786f, a dark bronze where the handle is a warm light grey), so it is fitted like the other colours: what comes out is a reflectance of about 0.35, under bare nickel's, as a coat with Teflon in it would be. Primary Arms lists its colour as Silver; AR15Discounts' smaller picture of the same handle (0ccff605b7c4) reads lighter, #a1998d over the whole of it."},"radian-lt-fde":{"label":"Radian Raptor-LT Flat Dark Earth (polymer)","hex":"#a58c71","calibration":"appearance","source":"make color-match: radian-raptor-lt-charging-handle's left handle (its end face, turned to the camera) in the hero direction, light backdrop, build aero-556, under polymer (matte), fitted to references/radian-raptor-lt-charging-handle 7629c52d4d97 (Primary Arms' R0149 from above: two flats of the handles beside the pivots, regions [875,280,930,330] and [1290,260,1350,320], read #867257 and #836f56) and ecb818757aad (its photo from below, regions [275,400,335,440] and [250,960,330,1010], #7d664f and #877158), averaged #846f56 and carried into the app's light by the black handle of the same series (5d168cd4d6e1, region [875,280,930,330], reads #111010 where the app draws black polymer #2f2f31 on the fitted face: that much added in linear light, #8a7661); rendered #8a7662 for a target of #8a7661","family":"polymer","note":"Primary Arms' two photos agree within 9 levels. Wing Tactical's photo of it from below (3db091fb55bd, region [150,560,260,700]) reads #ad9e81, lighter and greyer as all of its photos of these handles are, and the maker's artwork (9aa713419a72) #a8968a: neither is in the target. Fitted without the black handle's correction it is #9c8261 (rendered #836f56). Sellers say the handles' colours \"are designed to match standard Magpul® color offerings\" (Wing Tactical): the app's Magpul Flat Dark Earth is #8c7556, darker than this by these photos."},"radian-lt-grey":{"label":"Radian Raptor-LT Grey (polymer)","hex":"#4a4b57","calibration":"appearance","source":"make color-match: radian-raptor-lt-charging-handle's left handle (its end face, turned to the camera) in the hero direction, light backdrop, build aero-556, under polymer (matte), fitted to references/radian-raptor-lt-charging-handle 4b09812fc092 (Primary Arms' R0150 from above: two flats of the handles beside the pivots, regions [780,170,860,240] and [1400,150,1480,230], read #373840 and #373941), carried into the app's light by the black handle of the same series (5d168cd4d6e1, region [875,280,930,330], reads #111010 where the app draws black polymer #2f2f31 on the fitted face: that much added in linear light, #46474e); rendered #46474f for a target of #46474e","family":"polymer","note":"One photo's two flats (the series' other photo of the grey shows its handles in shade). A dark slate, bluer than neutral. Primary Arms' photos are dark at their dark end (its black handle reads #111010): fitted to the photo's reading as it stands the grey is #323441 and draws within 8 levels of the black handle (#373840 beside #2f2f31), so the reading is carried by the black one first. Wing Tactical's close-up (3231df18cd03, region [960,770,1100,850]) reads #71787b, far lighter, and the maker's artwork (9aa713419a72) #505662. It comes out beside the app's Magpul Stealth Gray (#4e4f53), which sellers say it is made to match."},"radian-sd-fde":{"label":"Radian Raptor-SD Flat Dark Earth","hex":"#8c6d48","calibration":"appearance","source":"make color-match: radian-raptor-sd-charging-handle's latch (the left latch's tip, the face turned to the camera, region [800,480,960,630]) in the hero direction, light backdrop, build aero-556, under anodized_matte, fitted to references/radian-raptor-sd-charging-handle 5b965fca6fda (Primary Arms' R0066_01, the SD's T from above: two latch flats, regions [1595,462,1705,517] and [715,165,792,242], read #765e47 and #745b3f, averaged #755d43); rendered #755d43 for a target of #755d43","family":"anodize","note":"Radian's page sells the SD's colours as \"Cerakote Color Options\" over the anodize, Primary Arms says \"finished in Mil-Spec FDE anodizing\"; drawn as the Raptor's are (anodized_matte). Beside radian-fde (the Raptor's R0003 in the same series and pose, #957e66) this one is darker and browner, with the two photos' logos (#b3b4ac, #bab9b5) and black blocks (#2d2a29, #373634) within 10 levels of each other."},"reptilia-clear":{"label":"Reptilia clear anodize","hex":"#d3b071","calibration":"appearance","source":"make color-match JOB=accessory-clear (2026-10-28): original AUS mount alone on carbine at slot 8, camera [0.45,0.3,-1] at 10 in, light backdrop, 1600 x 1000. Its lit front clamp face [668,690,728,755] under anodized_matte renders #af9363 from #d3b071, matching the maker's Clear 100-118 oblique photo eeb891756f2e bridge flat [280,616,350,643]. The separate top photo bf5ec607d063 bridge [285,480,365,523] reads #ba9e67 (11 levels brighter in red/green, 4 in blue). Main and right views reviewed; steel hardware stays black.","family":"anodize","note":"Clear hardcoat on the original AUS: olive bronze with warm gold lit faces in the manufacturer's separate oblique and top photos. This one matte preset matches the warm lit flat; it does not reproduce the full olive-to-gold variation with reflected light. Exposure and white balance are the photographer's, with no grey card. This is an appearance approximation, not a physical color specification."},"reptilia-fde":{"label":"Reptilia flat dark earth anodize","hex":"#d2b073","calibration":"appearance","source":"make color-match: the AUS mount's front clamp block, its left face beside the cross bolt's head, in the hero direction, light backdrop, build carbine with the mount alone at slot 8 in flat dark earth, under anodized_matte, region [668,690,728,755] of a 1600 x 1000 view at 10 in, fitted to Silencer Shop's photograph of the FDE mount from the front left (references/reptilia-aus-30mm-mount 0bf480654d9e, the bridge's side left of the word REPTILIA, [295,608,370,640]: #ae9364; and the base's side behind the rear boss, [600,655,700,690]: #ad9466): rendered #ae9364; the bridge's side under the arm renders #a88e61 and the rear clamp's face #ad9263 in the same picture (2026-10-20, .cache/color-match/reptilia-refit).","family":"anodize","note":"Reptilia: \"Flat Dark Earth Anodize\" (100-122), \"MIL-STD, Type III, Class 2, hard anodize coating\". Matched to Silencer Shop's studio photograph of the FDE mount, the one photograph of the colourway on file: the maker's own FDE picture is its black one recoloured, and no colour is fitted to it. The photograph's light is from its left: the flank is its brightest face, and its rings' faces and the bolts' bosses are in its shade, a greener khaki (#7b7a5d). A first fit on the bridge's side under the arm, in a closer view where that face read a fifth darker than the mount's other lit flats, gave #f3ce89, the brightest flat dark earth on file and a light sand on the page; fitted on the clamp's face, a flat the app lights as it lights the faces every other colour on file was fitted on, three lit flats agree with the photograph's within six levels."},"reptilia-dot-fde":{"label":"Reptilia flat dark earth anodize (the DOT mounts)","hex":"#9f6d47","calibration":"appearance","source":"make color-match JOB=reptilia-dot (catalog batch 17, 2026-11-03): build v1 with the DOT mount at the red dot's place (index 12) in flat dark earth and a Micro T-2 on it, camera [0.45,0.3,-1] at 7 in, light backdrop, 1600 x 1000, under anodized_matte; the base's left face beside the cross bolt's seat, [600,720,800,810] on the 1.93 and [600,670,800,760] on the lower 1/3, renders #866046 from #9f6d47 (the lower 1/3 alone fits #9e6c46). Target: Primary Arms' square side photographs of the two in flat dark earth, the web's face under the logo: the 1.93 (references/reptilia-dot-mount-193 56a035336ff3, [880,730,1300,900]: #896247) and the lower 1/3 (references/reptilia-dot-mount-39mm 64c81bc1e76b, [830,760,1350,860]: #835f46), averaged.","family":"anodize","note":"Reptilia's \"Flat Dark Earth Anodized\" on its DOT mounts photographs as a copper-bronze, redder and darker than the AUS mount's (reptilia-fde, fitted to #ae9364 on its photograph's lit flank): a hard anodize's colour varies by batch and part, and these are the photographs of these parts (the maker's own line-ups and on-rifle pictures agree by eye). Rifle Supply's photograph of the 1.93 reads lighter (#997353) under its light; the maker's recoloured 100-037/100-038 pictures aren't read. Exposure and white balance are the photographers': an appearance match, not a specification."},"sb-tactical-sba4-fde":{"label":"SB Tactical FDE","hex":"#a68b76","calibration":"appearance","source":"make color-match: sb-tactical-sba4's housing (its left flat above the slots, the face the app's light falls on) in the hero direction, light backdrop, build bcm-16-mid with the brace in the stock's slot, under polymer (satin), fitted to a target predicted for the app's light. SB Tactical's own pictures of the brace in FDE and in black (references/sb-tactical-sba4 941602a65010 and dc891b83a89c: one series, one light, straight from its left) read the same region of the housing's side (rows 475 to 525, columns 300 to 1040) #c0a58f and #555555; that ratio in linear light, a channel at a time, of what the app renders the black brace as there (#414142) is #968171; rendered #968171 for a target of #968171","family":"polymer","note":"The maker's pictures are brightly lit renders (its black reads #555555), so the FDE is fitted by its ratio to the black of the same series, not by its reading alone."},"sb-tactical-sba4-odg":{"label":"SB Tactical OD Green","hex":"#3a381a","calibration":"appearance","source":"make color-match: as the FDE, on references/sb-tactical-sba4 6f789e39e1ad (SB Tactical: the green brace straight from its left, the same series), whose region reads #61604e: the ratio to the black brace's #555555 (dc891b83a89c) of the app's #414142 is #4b4a3c; rendered #4b4a3e for a target of #4b4a3c (the satin sheen's white holds the blue two levels over)","family":"polymer"},"sb-tactical-sba3-fde":{"label":"SB Tactical FDE","hex":"#c7ad99","calibration":"appearance","source":"make color-match: sb-tactical-sba3's housing (its left side under the top's chamfer, the face the app's light falls on) in the hero direction, light backdrop, build bcm-16-mid with the brace in the stock's slot, under polymer (satin), fitted to a target predicted for the app's light, as sb-tactical-sba4-fde was. SB Tactical's own pictures of the SBA3 in FDE and in black (references/sb-tactical-sba3 300671e5046a and 379c7f22b44e: one series, one light, straight from its left) read the same region of the housing's side (rows 300 to 420, columns 700 to 1200) #c0aa98 and #4e4e4e; that ratio in linear light, a channel at a time, of what the app renders the black brace as there (#484849) is #b39e8f; rendered #b39e8f for a target of #b39e8f","family":"polymer","note":"Midwest Gun Works' photo of the FDE and the black SBA3 together (fb066a1c51d3) reads the FDE's housing #baa896 beside the black's #4a4a4a: the same ratio within 4 levels. Matched on the SBA3's own pictures; whether SB Tactical's FDE is one colour across its braces is for a match on two of them to say (sb-tactical-sba4-fde was fitted to #968171 on the SBA4's)."},"sb-tactical-sba3-odg":{"label":"SB Tactical OD Green","hex":"#615911","calibration":"appearance","source":"make color-match: as the FDE, on references/sb-tactical-sba3 77a3f5f5a0a6 (SB Tactical: SBA3-green-product_image.jpg, the same series; the only picture of the green SBA3 on file), whose region reads #6f6a45: the ratio to the black brace's #4e4e4e of the app's #484849 is #676240; rendered #676244 for a target of #676240 (the satin sheen's white holds the blue four levels over)","family":"polymer"},"sb-tactical-sba5-fde":{"label":"SB Tactical FDE","hex":"#9b7a4e","calibration":"appearance","source":"make color-match on the housing's lit side in the app's hero direction (camera dir [0.45, 0.3, -1]), to a target taken from references/sb-tactical-sba5 24198220d197 (SB Tactical: SBA5_Left_FDE-web.jpg, the FDE brace straight from its left on white): its housing's side (rows 398 to 491, columns 218 to 870, the darkest 10% and brightest 15% left out) reads #a88b63, against #4b4d4c for the same region of the black brace's picture of the same series (4d01fa8999c1); that ratio on the app's black brace there (#3f4041) is #8d7455; rendered #8d7455.","family":"polymer"},"sb-tactical-sba5-odg":{"label":"SB Tactical OD Green","hex":"#2f3224","calibration":"appearance","source":"make color-match as the FDE, on references/sb-tactical-sba5 c300cd24da81 (SB Tactical: SBA5_Left_ODG-scaled.jpg, the green brace from its left on white, a photograph; rows 680 to 837, columns 378 to 1478), whose region reads #515348: the ratio to the black brace's #4b4d4c of the app's #3f4041 is #44453e; rendered #454640 (the satin sheen's white holds it a level over).","family":"polymer"},"sb-tactical-stealth-gray":{"label":"SB Tactical Stealth Gray","hex":"#4f5560","calibration":"appearance","source":"make color-match: sb-tactical-sba4's housing (its left flat above the slots, the face the app's light falls on) in the hero direction, light backdrop, build bcm-16-mid with the brace in the stock's slot, under polymer (satin), fitted to a target predicted for the app's light, as sb-tactical-sba4-fde was. Primary Arms' own photographs of the brace in Stealth Gray and in black (references/sb-tactical-sba4 91a9ebe214f4 and 0ceacff4596a: one studio, one pose, straight from its left) read the housing's flat above the slots (regions [975,670,3100,800] and [850,550,3250,662], 119,500 px each) #636770 and #4c4c4e; that ratio in linear light, a channel at a time, of what the app renders the black brace as there (#414142) is #555960; rendered #555960 for a target of #555960","family":"polymer","note":"A cool, slightly blue grey, lighter than the black by about a third in Primary Arms' light. SB Tactical's own pages no longer show it, and the gray pictures sellers serve from distributors are the maker's black one tinted (the part's note): Primary Arms' photographs are the only ones on file. Whether SB Tactical's Stealth Gray is one colour across its braces is for a photograph of another brace in it to say."},"scalarworks-fde":{"label":"Scalarworks flat dark earth anodize","hex":"#d5c2c2","calibration":"appearance","source":"make color-match JOB=scalarworks-fde (2026-11-03): build v1 with the LEAP/02 (scalarworks-leap-02-micro-226) at the red dot's slot in flat dark earth and no dot on it, camera [0.45,0.3,-1] at 6 in, light backdrop, 1600 x 1000, under anodized_matte. The rear post's left face [1040,200,1125,460] renders #b2a2a2 from #d5c2c2, matching the maker's side photograph of SW0230-FDE (references/scalarworks-leap-02-micro-226 e27c207b94de: the rear post's left face [700,330,760,560], square to the lens: #b2a2a2). The clamp's left face behind the wheel renders #b0a1a1 against the photograph's #b7a8a6 there (7 levels).","family":"anodize","note":"The maker: \"Color — Type III hard anodized finish. Black FDE\" (its markup: \"flat-dark-earth\"). A warm grey-taupe in the maker's photographs, which read the body's lit flats within 10 levels of each other (#ad9e9f to #b7a8a6 on the side photo's left face); its three-quarter photo (ee9fe286117d) lights the near post brighter (#d1c2c2) and leaves the front post in shade (#7e7170): the side photo, the face square to the lens, is the target. An appearance from a photograph with no grey card, not a specification."},"sig-fde":{"label":"SIG flat dark earth","hex":"#b7a38d","calibration":"appearance","source":"make color-match: the ROMEO-MSR GEN II's left panel in the hero direction, light backdrop, build budget-16 with the sight in flat dark earth, under anodized_matte, fitted to SIG's rendering of SORMSR111 as two sellers show it: c4fea0598ed4 (Sportsman's Warehouse, regions [230,180,420,300] and [600,330,760,430], reads #988878 and #9c8b7a) and 1e3f18987926 (Alexander's, the same two flats, reads #948776 and #9f907d); rendered #9a8a79 for a target of #9a8a79 (the tube's flank above the panel renders #9f8f7d).","family":"other","note":"The one picture of the colour on file is a rendering, not a photo: its light is its artist's, and the two copies differ by 4 to 7 levels a channel (two sellers' compressions). No page says what the coat is (Sportsman's: \"Finish FDE\", \"Color Tan\"): drawn under the black sight's matte anodize, `anodized_matte`, and to be matched again if that changes or a photo of the sight turns up."},"sig-fde-romeo5":{"label":"SIG flat dark earth (ROMEO5 GEN II)","hex":"#ebd5b0","calibration":"appearance","source":"make color-match: the ROMEO5 GEN II's housing, its left flank in the hero direction, light backdrop, build aero-556 with the sight in Flat Dark Earth, under anodized_matte, region [720,380,1060,500], fitted to Midwest Gun Works' photograph of SOR5111 from the front left (references/sig-romeo5-gen-ii ec5b5b61c2c4, SGSOR5111-1, region [600,440,820,560] on the housing's left flank, reads #c4b294); rendered #c4b294 for a target of #c4b294. Its straight left side (5fc51c0b1652, SGSOR5111-3, region [300,320,520,430]) reads #bdab88, 7 to 12 levels darker a channel: the flat seen square from the side, away from the light.","family":"other","note":"Photographs of the sight itself, the distributor's set as a seller on file shows it (the ROMEO-MSR's sig-fde was matched to a rendering, and reads darker and cooler): a colour of its own. No page says what the coat is (Alexander's: \"Flat Dark Earth, matte\"): drawn under the black sight's matte anodize, to be matched again if that changes."},"silencerco-sparrow-phosphate":{"label":"SilencerCo Sparrow tube (magnesium phosphate)","hex":"#646566","calibration":"appearance","source":"make color-match: the Sparrow 22's outer tube (its side at mid-height) in the hero direction, light backdrop, build `suppressed`, under phosphate, fitted to the mean of Primary Arms' three views of SU75, the whole tube between its caps in each: two obliques (references/silencerco-sparrow-22 09c2b9592403, region [450,250,1650,1150], reads #5f5f60, and 09406a0f6baa, region [300,100,1500,1000], reads #585859) and the straight side view (7610478aca44, region [330,520,1950,940], reads #4a4a4c); rendered #565657 for a target of #565657","family":"metal","note":"The straight side view reads the tube darker than the two obliques, by its light (from above, the tube seen side on). Fitted to the obliques alone (#6b6c6d) the tube drew a light mid grey on a black rifle, lighter than any of the three photographs has it beside its own black caps; the three's mean is taken. A matte grey whose three readings span 21 levels by the light. The older preset silencerco-black-oxide (#4b4a4d, that side view's reading, never matched) is left in place and no longer used by the part."},"bcm-pnt-nickel":{"label":"BCM PNT electroless nickel","hex":"#96928f","calibration":"appearance","source":"make color-match: the PNT trigger's tail, its flat left side, in the hero direction, light backdrop, build bcm-16-mid drawn apart (the exploded view: the trigger is inside the receiver otherwise), under nickel, fitted to BCM's two photos of the assembly: the trigger's own body flat in the side view (references/bcm-pnt-trigger 96d05cd190c7, region [550,745,720,835], reads #8d8689) and its tail's lit side in the three-quarter view (dac53da6ba38, region [860,1060,1000,1180], reads #94938e), their mean #918d8b; rendered #918d8b for a target of #918d8b, and the body's flat ahead of the pin in the same render reads #9b9794","family":"metal","note":"A plated metal: its picture is its reflections, and the fit holds for the hero view's flat (13,000 px). A first fit on the bow's narrow flank (1,400 px) gave #bdb8b6, and the trigger's flats drew near white under the app's light, brighter than any of BCM's photos has them. The hammer in the same two photos reads darker, #7f7c80 and #8c8a84: by its face's turn to the light, the two being one plating. A first try from 3.5 in fitted nothing: the rifle, not the backdrop, stood in the corner the tool reads the backdrop's level from, and the fit ran to white (a fault of the framing, not of the finish)."},"steel-phosphate-charcoal":{"label":"Manganese phosphate, charcoal","hex":"#464644","calibration":"appearance","source":"make color-match: bcm-16-mid-barrel's tube between the collar and the chamber in the hero direction, light backdrop, exploded, build bcm-16-mid, under phosphate, fitted to references/bcm-16-mid-barrel 99b8653ffc94 (Primary Arms' side view, 4848 x 3232, region [100,1400,4700,1800], the whole barrel, reads #3a3a38) and 64064a2cab47 (Primary Arms' three-quarter view, regions [1000,950,1500,1250] and [2500,1500,3000,1800], read #454545 and #434342); rendered #3f3f3e for a target of #3f3f3e","family":"metal","note":"BCM's barrel, dry. One seller's two photos, ten levels apart; BCM's own of the barrel are 500 px on a wooden block and aren't read. The fit stepped between #454544 and #474744; the middle was then rendered on its own, and read the target."},"steel-phosphate-dark":{"label":"Manganese phosphate, dark charcoal","hex":"#313134","calibration":"appearance","source":"make color-match: bcm-bcg's tail in the hero direction, light backdrop, exploded, build bcm-16-mid, under phosphate with the satin sheen, fitted to references/bcm-bcg 60260580e01f (BCM's own side view, region [10,380,990,560], the whole group, reads #36373b) and 36cc65af4f82 (Primary Arms' side view, region [40,260,1110,470], reads #3a3a38); rendered #38383a for a target of #38383a (and #39393b on the carrier's front half)","family":"metal","note":"BCM's carrier group, oiled. The maker's photo and a seller's, four levels apart. Under BCM's barrel's charcoal (#464644) the carrier's flats rendered #454544, thirteen levels over its photos: a carrier is photographed darker than a barrel, and has its own colour. Which of its pieces reads lighter changes with the photo (the key against the tail: #40403b against #323230 in Primary Arms', #2f3034 against #414143 in BCM's), so the group is one colour."},"steel-phosphate-black":{"label":"Phosphate, black","hex":"#1f1f1d","calibration":"appearance","source":"make color-match: bcm-750-gas-block's left side in the hero direction, light backdrop, exploded, build bcm-16-mid, under phosphate, fitted to references/bcm-750-gas-block 8c329d289596 (Primary Arms' side view, region [700,200,1500,1300], reads #222320) and 3ce1f7e276b9 (its three-quarter view, region [500,100,1700,1400], reads #2c2c2b); rendered #272726 for a target of #272726","family":"metal","note":"BCM's gas block and the A2 flash hider: a blacker phosphate than BCM's barrel in the same seller's photos (#3a3a38 there). BCM's own two of the block read #302f2f and, lit harder, #575759 (2509846565db, dc4f60fefbd5); a retouched grey one (bcdd79b56f78) isn't used. On the flash hider it renders #20201f on the body under the slots and #252524 on the collar, where its two makers' own photos read #1b2024 (BCM's, references/a2-flash-hider 9f6749f9e2da) and #1c2124 (Windham's, edeff5c5fbd9): within ten levels, without their blue cast. Wing Tactical's photo of Aero's hider is a dry charcoal, #4d4d4d (434008668843): the lighter of the two looks phosphate is photographed in, and not the one drawn."},"steel-parkerized":{"label":"Parkerized, dark grey","hex":"#404045","calibration":"appearance","source":"make color-match: bca-556-16-mid-barrel's tube between the collar and the chamber in the hero direction, light backdrop, exploded, build budget-16, under phosphate with the satin sheen, fitted to references/bca-556-16-mid-barrel eff6b190e339 and 53fbcf1e58d8 (Primary Arms' side and three-quarter views, the whole barrel, read #47474e and #44444d) and b6429b8b7d3c and a1a4be9489ee (Dirty Bird's and AR15Discounts', read #3e3e3c and #3f3f3d); rendered #424245 for a target of #424245","family":"metal","note":"Bear Creek's barrel. Two sellers' pairs: Primary Arms' oiled, with a blue cast (18 levels more blue than the other pair, 9 more red and green), Dirty Bird's and AR15Discounts' dry and neutral. Neither is the maker's (Bear Creek's own photo is 485 px), so the target is the mean of the four, which is within ten levels of each on every channel but Primary Arms' blue. Three levels from BCM's manganese phosphate: by these photos the two finishes are one colour, and what differs is the oil."},"steel-nitride-black":{"label":"Black nitride","hex":"#1d1e20","calibration":"none","source":"Not fitted to a photo: the hex is the catalog's placeholder black (data/finishes.yaml, `placeholder-black`), under the `nitride` finish.","family":"metal","note":"Not matched, and not to be: salt-bath nitride (QPQ, Melonite) is a polished black, and what a photo reads on it is the studio's lights in it (Toolcraft's carrier reads #252428 on its tail in AR15Discounts' photo and Aero's #808080 where a softbox lies along it; Aero's barrel #474747, its gas block #312e2e). The `nitride` finish carries its look."},"superlative-matte-stainless":{"label":"Superlative matte stainless","hex":"#eeefec","calibration":"appearance","source":"make color-match: superlative-750-gas-block's left flank below the detent's groove in the hero direction, light backdrop, exploded view (the block is inside a handguard otherwise), build bcm-16-mid with this block and no handguard, under steel, fitted to a80edfa7809c (Wing Tactical's own photo of a stainless set-screw block, region [850,800,1100,1000], reads #b3b4b1) and b8b463a02350 (Wing Tactical's photo of the five blocks, the stainless set-screw one, region [900,290,1050,400], reads #cbcbc9; its stainless clamp-on #bfbfbd); rendered #bcbdba for a target of #bcbdba","family":"metal","note":"Bead-blasted bare 416 stainless (Right To Bear: \"Finish - Stainless Steel, Matte\"): an even pale grey with no bright line, so it is fitted like a paint under the app's matte steel and not drawn as brushed stainless. The albedo is near white because that finish is three quarters metal and darkens what it is given. Wing Tactical's three photos agree within 24 levels; the maker's older marketing picture of the stainless block (e3060a28050c, at AR15Discounts) is darker and pinkish (#8e8289) under a light of its own and wasn't taken. The curved top of the block renders a little lighter (#cdcdcb)."},"superlative-tan-dlc":{"label":"Superlative Tan DLC","hex":"#cfaa8c","calibration":"appearance","source":"make color-match: superlative-750-gas-block's left flank below the detent's groove in the hero direction, light backdrop, exploded view, build bcm-16-mid with this block (option tan) and no handguard, under steel, fitted to bc8e61f05e93 (the maker's marketing picture of SABO-DI-750ST at Bauer Precision, 750 x 750, region [259,259,371,371], reads #ab8b73) and 351d4aa42e07 (the maker's second picture of it at Huckleberry Arms, 750 x 750, region [249,289,391,351], reads #997d67); rendered #a2846d for a target of #a2846d","family":"metal","note":"A tan diamond-like carbon coat over blasted stainless (Bauer Precision: \"Finish: Tan Diamond-Like Carbon (DLC)\"): matte, with a soft metallic cast, drawn under the app's matte steel. Two pictures of two lots disagree: the maker's current marketing pictures (Lot # 022123) are this pinkish tan; Wing Tactical's own photo of the three finishes side by side (b8b463a02350, Lot # 100417) has the tan block a brassy gold (#d2bf7d). The maker's was taken, being the picture three sellers show for the number; a block in hand may be either. Both source pictures are 750 px: the largest any page read has. The two readings are 18 levels apart (two faces of the block under one light)."},"surefire-tan":{"label":"SureFire Tan","hex":"#bfa890","calibration":"appearance","source":"make color-match: the Scout Light Pro Dual Fuel's tube in the hero direction, light backdrop, build aero-556-fitted with the light on the handguard's left M-LOK, under anodized_matte, fitted to 592808c17b7c (Sportsman's Warehouse's photograph of a tan M640DF-TN-PRO side on, region [300,560,440,680], reads #a18c78) and 84193a6f917f (the same unit from the front, region [400,440,600,560], reads #a69482); rendered #a3907d for a target of #a3907d","family":"anodize","note":"Matched to a seller's photographs of one unit, the only pictures on file that aren't artwork: SureFire's own picture of the tan light is a render in a neutral grey (#c3c0bc on the tube) with a cream mount, and Rifle Supply's copy of that render is a saturated tan (#af9477). A third photograph of the same unit, from behind, reads lighter (#b8a28b). On the unit the head's middle ring is darker than the tube (#8f7c6e): SureFire's tan differs piece to piece and batch to batch, and one tone is drawn."},"surefire-dlc-black":{"label":"SureFire DLC black","hex":"#1d1e20","calibration":"none","source":"Not fitted to a photo: the hex is the catalog's placeholder black (data/finishes.yaml, `placeholder-black`), under the `nitride` finish.","family":"metal","note":"Not matched, and not to be: SureFire's diamond-like carbon coat on its stainless muzzle devices (\"DLC Coating\"; Primary Arms: \"Black Ionbond DLC coating\") is a smooth black on hard steel, and what a photo reads on it is the studio's light (see the parts' notes for the readings). The catalog has no finish type for DLC: drawn under `nitride`, the nearest."},"surefire-dark-earth-cerakote":{"label":"SureFire Dark Earth","hex":"#c59e71","calibration":"appearance","source":"make color-match: the SOCOM556-RC2's tube in the hero direction, light backdrop, build bcm-16-mid with the suppressor on a muzzle device, under cerakote, fitted to the tube's lit flat in Primary Arms' photographs of the Dark Earth one (references/surefire-socom556-rc2): 2ef29d436724 (from the side, region [600,560,1300,700], reads #ad8c64), c5a2d597da99 (from ahead, [700,430,1100,560], #ab8b6c), 0b6cdb056ffe (from behind, [900,500,1300,620], #a88660) and 2b4e7d4cd0be (standing, [930,450,1080,900], #ae8c67), their mean #ab8a66; rendered #ab8a66 for a target of #ab8a66 (the lock ring beside it in the same render reads #aa8965)","family":"cerakote","note":"SureFire's \"Dark Earth\" on its SOCOM suppressors (\"DLC and Cerakote™ Finish\"; Primary Arms: \"Color Flat Dark Earth\", \"Finish Cerakote\"). Four photographs of one unit agree within 6 levels a channel. Its lock ring reads the same in one view (#b18863) and brighter and more golden where a flute faces the light (#cca075): one tone is drawn. No picture of SureFire's own shows the Dark Earth one (its page has the black one only), so this is one seller's light."},"taurus-white-dot":{"label":"Taurus front sight dot, white","hex":"#e6e6e2","calibration":"none","source":"Not fitted to a photo: the dot is on the front sight's rear face, toward the eye, and no photo on file looks at it from behind (Sportsman's views are from the front and the sides). A look-dev white for a painted dot, a little under paper white.","family":"other","note":"\"White-dot front sight\" (Taurus shop, the T.O.R.O. kit); \"white dot front\" (American Rifleman)."},"unity-fde":{"label":"Unity flat dark earth anodize","hex":"#d09e6b","calibration":"appearance","source":"make color-match JOB=unity-fde (2026-11-03): build v1 with the mount at the red dot's slot in flat dark earth and a ROMEO5 on it, camera [0.45,0.3,-1] at 8 in, light backdrop, 1600 x 1000, under anodized_matte. The left face under the oval window [760,395,990,428] renders #ae8660 from #d09e6b, matching Primary Arms' photograph of the FDE mount's left side from ahead and above (references/unity-fast-micro-226 132598ee129a, FST-MICF_02.jpg: the face under the oval window [900,640,1300,690]: #ae8660). The face above the rear pocket renders the same, against the photograph's #a8805d there (6 levels). Read straight off the photograph before the fit: #9f7652 on the square right side (52f6e3ffa50f), which the app's light rendered #87684e.","family":"anodize","note":"Primary Arms: \"Type III hardcoat anodized flat dark earth\" and \"FDE is used to describe the wide range of brown, tan, and bronze colors\"; TNVC: \"color may vary from part to part (even parts done in the same batch)\". The sellers' photographs differ by as much: Primary Arms' (the seller whose offer is on file) a warm brown, Rifle Supply's three (250d1c931401, 21330942adc2, daf1712b069b) an olive khaki (#a1905b to #d2bf7a on lit flats). Matched to Primary Arms'. An appearance from a photograph with no grey card, not a specification."},"vltor-a5-buffer-bronze":{"label":"VLTOR A5 buffer, bronze anodize","hex":"#4c2a07","calibration":"appearance","source":"make color-match: the A5H2's body down its lit side in the hero direction (region [620,450,1000,520]), light backdrop, build bcm-16-mid with VLTOR's tube, buffer and spring, drawn apart, under anodized_matte, fitted to VLTOR's picture of its SP-A5 kit (references/vltor-a5-buffer-spring 2531fc1da290: the body down its lit middle, [165,320,210,520], reads #564122) through the exposure above: #4d391d; rendered #4d392e for a target of #4d391d","family":"anodize","note":"A dark bronze brown. Its blue is at the albedo's floor and renders 17 levels over the target: drawn a little cooler and less yellow than the picture, as no anodize under this finish can be drawn more so. VLTOR's close view of the head (references/vltor-a5h2-buffer 7dfeb8e9eab3) has its face an olive khaki (#757055) and the body's lit side near white under a hard studio light, and its picture of the buffer in its card (746290c9afa4) a lighter bronze through the card's plastic (#6b5738): neither is the body's side as the app shows it. Before: #564122, read off the picture."},"vltor-a5-buffer-bumper":{"label":"VLTOR A5 buffer bumper, translucent white","hex":"#e0d8c2","calibration":"appearance","source":"make color-match: the bumper's side in the hero direction (region [1105,420,1160,480]), light backdrop, the same build and shot, under polymer, fitted to VLTOR's picture of its SP-A5 kit (references/vltor-a5-buffer-spring 2531fc1da290: the bumper's side, [166,262,212,284], reads #d5cfbe) through the exposure above: #c1baa8; rendered #c1baa8 for a target of #c1baa8","family":"polymer","note":"A translucent milky white in VLTOR's pictures, drawn opaque (BCM's and Guntec's bumpers are too); a little warmer than Guntec's white bumper. Before: #d5cfbe, read off the picture."}}},"platforms":{"ar15":{"id":"ar15","label":"AR-15 pattern","root":"lower_receiver","groups":{"lower":"Lower","stock":"Stock","upper":"Upper","mounts":"Accessories"},"standin":"bcm-16-mid","hand":"grip","noun":"rifle","bore":"std.ar15.bore_axis_y","markers":[{"label":"takedown pin"},{"label":"pivot pin","at":"std.ar15.pin_spacing"}],"eye_from":{"at":"std.ar15.receiver_rear_x","words":"the receiver's rear face"},"nfa":{"barrel":"barrel","muzzle":"muzzle","barrel_min":"std.nfa.rifle_barrel_min","overall_min":"std.nfa.rifle_overall_min","shoulder":"stock","brace":"brace","grip":"grip","foregrip":"vertical_grip"},"slots":{"lower_receiver":{"category":"lower","also":[],"needed":true,"guided":true,"listed":"always","group":"lower"},"lpk":{"category":"lpk","also":[],"needed":true,"guided":true,"listed":"always","group":"lower","mate":{"parent":"lower_receiver","parentInterface":"lpk","interface":"lpk"}},"selector":{"category":"selector","also":[],"needed":false,"guided":false,"listed":"always","group":"lower","mate":{"parent":"lower_receiver","parentInterface":"selector","interface":"selector","apart":[0,0,-1]}},"trigger":{"category":"trigger","also":[],"needed":true,"guided":true,"listed":"always","group":"lower","mate":{"parent":"lower_receiver","parentInterface":"fcg","interface":"fcg","apart":[0,1,0]}},"trigger_guard":{"category":"trigger_guard","also":[],"needed":true,"guided":true,"listed":"always","group":"lower","mate":{"parent":"lower_receiver","parentInterface":"trigger_guard","interface":"trigger_guard","apart":[0,-1,0]}},"grip":{"category":"grip","also":[],"needed":true,"guided":true,"listed":"always","group":"lower","mate":{"parent":"lower_receiver","parentInterface":"grip_lug","interface":"grip_lug","apart":[0,-1,0]}},"magazine":{"category":"magazine","also":[],"needed":false,"guided":true,"listed":"always","group":"lower","mate":{"parent":"lower_receiver","parentInterface":"magwell","interface":"magwell","apart":[0,-1,0]}},"folding_adapter":{"category":"folding_adapter","also":[],"needed":false,"guided":false,"listed":"always","group":"stock","mate":{"parent":"lower_receiver","parentInterface":"buffer_tube_mount","interface":"receiver_thread","apart":[-1,0,0]}},"receiver_extension":{"category":"receiver_extension","also":[],"needed":true,"guided":true,"listed":"always","group":"stock","mate":{"parent":"lower_receiver","parentInterface":"buffer_tube_mount","interface":"receiver_thread","apart":[-1,0,0]}},"end_plate":{"category":"end_plate","also":[],"needed":true,"guided":true,"listed":"always","group":"stock","mate":{"parent":"receiver_extension","parentInterface":"extension_end","interface":"extension_end","apart":[1,0,0]}},"castle_nut":{"category":"castle_nut","also":[],"needed":true,"guided":true,"listed":"always","group":"stock","mate":{"parent":"end_plate","parentInterface":"nut_seat","interface":"nut_seat","apart":[-1,0,0]}},"buffer":{"category":"buffer","also":[],"needed":true,"guided":true,"listed":"always","group":"stock","mate":{"parent":"receiver_extension","parentInterface":"bore","interface":"bore","apart":[1,0,0]}},"buffer_spring":{"category":"buffer_spring","also":[],"needed":true,"guided":true,"listed":"always","group":"stock","mate":{"parent":"receiver_extension","parentInterface":"bore","interface":"bore","apart":[1,0,0]}},"stock":{"category":"stock","also":["brace"],"needed":true,"guided":true,"listed":"always","group":"stock","mate":{"parent":"receiver_extension","parentInterface":"tube","interface":"tube","indexParam":"stock_position","apart":[-1,0,0]}},"upper_receiver":{"category":"upper","also":[],"needed":true,"guided":true,"listed":"always","group":"upper","mate":{"parent":"lower_receiver","parentInterface":"receiver_pins","interface":"receiver_pins","apart":[0,1,0]}},"barrel":{"category":"barrel","also":[],"needed":true,"guided":true,"listed":"always","group":"upper","mate":{"parent":"upper_receiver","parentInterface":"barrel_extension","interface":"barrel_extension","apart":[1,0,0]}},"handguard":{"category":"handguard","also":[],"needed":true,"guided":true,"listed":"always","group":"upper","mate":{"parent":"upper_receiver","parentInterface":"handguard_mount","interface":"handguard_mount","apart":[0,-1,0]}},"barrel_nut":{"category":"barrel_nut","also":[],"needed":false,"guided":false,"listed":"needed","group":"upper","mate":{"parent":"upper_receiver","parentInterface":"handguard_mount","interface":"handguard_mount","apart":[1,0,0]}},"delta_ring":{"category":"delta_ring","also":[],"needed":false,"guided":false,"listed":"needed","group":"upper","mate":{"parent":"barrel_nut","parentInterface":"delta_ring","interface":"delta_ring","apart":[1,0,0]}},"gas_block":{"category":"gas_block","also":[],"needed":true,"guided":true,"listed":"always","group":"upper","mate":{"parent":"barrel","parentInterface":"gas_journal","interface":"gas_journal","apart":[0,1,0]}},"handguard_cap":{"category":"handguard_cap","also":[],"needed":false,"guided":false,"listed":"needed","group":"upper","mate":{"parent":"gas_block","parentInterface":"handguard_cap","interface":"handguard_cap","apart":[-1,0,0]}},"front_sight_post":{"category":"front_sight_post","also":[],"needed":false,"guided":false,"listed":"offered","group":"upper","mate":{"parent":"gas_block","parentInterface":"front_sight_post","interface":"front_sight_post","apart":[0,1,0]}},"gas_tube":{"category":"gas_tube","also":[],"needed":true,"guided":true,"listed":"always","group":"upper","mate":{"parent":"gas_block","parentInterface":"gas_tube","interface":"gas_tube"}},"bolt_carrier_group":{"category":"bolt_carrier_group","also":[],"needed":true,"guided":true,"listed":"always","group":"upper","mate":{"parent":"upper_receiver","parentInterface":"carrier_channel","interface":"carrier_channel","apart":[-1,0,0]}},"charging_handle":{"category":"charging_handle","also":[],"needed":true,"guided":true,"listed":"always","group":"upper","mate":{"parent":"upper_receiver","parentInterface":"charging_handle_channel","interface":"charging_handle_channel","apart":[-1,0,0]}},"muzzle":{"category":"muzzle_device","also":[],"needed":true,"guided":true,"listed":"always","group":"upper","mate":{"parent":"barrel","parentInterface":"muzzle","interface":"thread","apart":[1,0,0]}},"suppressor":{"category":"suppressor","also":[],"needed":false,"guided":false,"listed":"always","group":"upper","mate":{"parent":"muzzle","parentInterface":"suppressor_mount","interface":"mount","apart":[1,0,0]}}},"checks":[{"slot":"gas_tube","interface":"gas_system","with":"barrel","withInterface":"gas_system","note":"A gas tube is carbine, mid or rifle length, as the barrel's gas system is."},{"slot":"handguard","interface":"gas_system","with":"barrel","withInterface":"gas_system","note":"A drop-in handguard reaches from the delta ring to the cap behind the front sight base, which stands where the barrel's gas port is.","optional":true,"message":"{slot} is made for another length of gas system than {with}: its front wouldn't meet the cap behind the front sight base, which stands at the gas port"},{"slot":"barrel_nut","interface":"drop_in","with":"handguard","withInterface":"drop_in","missing":"{with} is a free-float handguard, on a barrel nut of its own: {slot} is for a drop-in handguard, held by a delta ring and a cap"},{"slot":"delta_ring","interface":"drop_in","with":"handguard","withInterface":"drop_in","missing":"{with} is a free-float handguard, on a barrel nut of its own: {slot} holds the rear of a drop-in handguard"},{"slot":"handguard_cap","interface":"drop_in","with":"handguard","withInterface":"drop_in","missing":"{with} is a free-float handguard: {slot} holds the front of a drop-in handguard"}],"cartridge":{"chamber":"barrel","slots":{"barrel":{"says":"is chambered for"},"bolt_carrier_group":{"says":"is made for"},"magazine":{"says":"holds"},"muzzle":{"says":"is rated for","optional":true},"suppressor":{"says":"is rated for","optional":true}}}},"taurus-tx22":{"id":"taurus-tx22","label":"Taurus TX22","root":"frame","groups":{"pistol":"Pistol","mounts":"Accessories"},"standin":"tx22-toro","hand":{"slot":"frame","anchor":"grip"},"noun":"pistol","bore":"taurus-tx22-frame.bore_axis_y","length":{"rear":{"slot":"frame","anchor":"rear"},"front":["suppressor","muzzle"]},"markers":[{"label":"rear pin"}],"view":{"min":[9,6],"orbit":14},"nfa":{"barrel":"barrel","muzzle":"muzzle","barrel_min":"std.nfa.rifle_barrel_min","overall_min":"std.nfa.rifle_overall_min","made":"handgun","foregrip":"vertical_grip"},"slots":{"frame":{"category":"pistol_frame","also":[],"needed":true,"guided":true,"listed":"always","group":"pistol"},"slide":{"category":"slide","also":[],"needed":true,"guided":true,"listed":"always","group":"pistol","mate":{"parent":"frame","parentInterface":"slide","interface":"frame","apart":[0,1,0]}},"barrel":{"category":"pistol_barrel","also":[],"needed":true,"guided":true,"listed":"always","group":"pistol","mate":{"parent":"slide","parentInterface":"barrel","interface":"slide","apart":[1,0,0]}},"muzzle":{"category":"muzzle_device","also":[],"needed":false,"guided":false,"listed":"always","group":"pistol","mate":{"parent":"barrel","parentInterface":"muzzle","interface":"thread","apart":[1,0,0]}},"suppressor":{"category":"suppressor","also":[],"needed":false,"guided":false,"listed":"always","group":"pistol","mate":{"parent":"muzzle","parentInterface":"suppressor_mount","interface":"mount","apart":[1,0,0]}},"magazine":{"category":"pistol_magazine","also":[],"needed":false,"guided":true,"listed":"always","group":"pistol","mate":{"parent":"frame","parentInterface":"magwell","interface":"magwell","apart":[0,-1,0]}}},"checks":[],"cartridge":{"chamber":"barrel","slots":{"barrel":{"says":"is chambered for"},"magazine":{"says":"holds"},"muzzle":{"says":"is rated for","optional":true},"suppressor":{"says":"is rated for","optional":true}}}}},"builds":{"aero-16-light":{"version":11,"id":"aero-16-light","name":"Aero 16 in, slick rail and a 1-6x","platform":"ar15","parts":{"lower_receiver":"aero-m4e1-stripped-lower","lpk":"rise-lpk","trigger":"geissele-ssa-e","grip":"magpul-moe-k2-plus","magazine":"magpul-pmag-20-gen-m3","receiver_extension":"bcm-receiver-extension","end_plate":"bcm-end-plate","castle_nut":"bcm-castle-nut","buffer":"bcm-carbine-buffer","buffer_spring":"bcm-carbine-action-spring","stock":"mft-battlelink-minimalist-stock","upper_receiver":"aero-m4e1-threaded-upper","barrel":"faxon-16-pencil-barrel","handguard":"aero-s-one-15-handguard","gas_block":"bcm-625-gas-block","gas_tube":"aero-mid-gas-tube","muzzle":"a2-flash-hider","bolt_carrier_group":"aero-556-bcg","charging_handle":"radian-raptor-lt-charging-handle"},"mounts":{"scope_mount":{"part":"primary-arms-deluxe-30mm-mount","host":"upper_receiver","interface":"top_rail","index":8},"optic":{"part":"primary-arms-slx-1-6x24-gen-iv","host":"scope_mount","interface":"rings","index":0}},"params":{"stock_position":1},"finishes":{},"fitments":{},"owned":[],"kits":["bcm-stock-kit","primary-arms-slx-1-6x24-nova-deluxe-mount-kit"]},"aero-556-fitted":{"version":11,"id":"aero-556-fitted","name":"Aero 5.56 carbine, fitted out","platform":"ar15","parts":{"lower_receiver":"aero-m4e1-lower","upper_receiver":"aero-m4e1-threaded-upper","barrel":"aero-556-16-mid-barrel","handguard":"aero-r-one-15-handguard","gas_block":"aero-750-gas-block","gas_tube":"aero-mid-gas-tube","bolt_carrier_group":"aero-556-bcg","charging_handle":"aero-charging-handle","muzzle":"a2-flash-hider","magazine":"magpul-pmag-30-gen-m3"},"mounts":{"optic_mount":{"part":"holosun-aro-163-mount","host":"upper_receiver","interface":"top_rail","index":8},"optic":{"part":"holosun-aro","host":"optic_mount","interface":"deck","index":0},"backup_sight":{"part":"magpul-mbus-pro-rear","host":"upper_receiver","interface":"top_rail","index":5,"folded":true},"backup_sight_2":{"part":"magpul-mbus-pro-front","host":"handguard","interface":"top_rail","index":34,"folded":true},"light":{"part":"surefire-scout-light-pro-dual-fuel","host":"handguard","interface":"mlok","index":4,"face":"right"},"sling_mount":{"part":"magpul-mlok-qd-sling-mount","host":"handguard","interface":"mlok","index":0,"face":"left"}},"params":{},"finishes":{},"fitments":{},"owned":[],"kits":[]},"aero-556":{"version":11,"id":"aero-556","name":"Aero 5.56 carbine","platform":"ar15","parts":{"lower_receiver":"aero-m4e1-lower","upper_receiver":"aero-m4e1-threaded-upper","barrel":"aero-556-16-mid-barrel","handguard":"aero-r-one-15-handguard","gas_block":"aero-750-gas-block","gas_tube":"aero-mid-gas-tube","bolt_carrier_group":"aero-556-bcg","charging_handle":"aero-charging-handle","muzzle":"a2-flash-hider","magazine":"magpul-pmag-30-gen-m3"},"mounts":{"optic_mount":{"part":"holosun-aro-163-mount","host":"upper_receiver","interface":"top_rail","index":8},"optic":{"part":"holosun-aro","host":"optic_mount","interface":"deck","index":0}},"params":{},"finishes":{},"fitments":{},"owned":[],"kits":[]},"aero-m4e1-pencil":{"version":11,"id":"aero-m4e1-pencil","name":"Aero M4E1 Enhanced, pencil barrel","platform":"ar15","parts":{"lower_receiver":"aero-m4e1-stripped-lower","lpk":"rise-lpk","selector":"radian-talon-safety-selector","trigger":"geissele-ssa-e","grip":"magpul-moe-k2-plus","magazine":"magpul-pmag-30-gen-m3","receiver_extension":"bcm-receiver-extension","end_plate":"bcm-end-plate","castle_nut":"bcm-castle-nut","buffer":"bcm-carbine-buffer","buffer_spring":"bcm-carbine-action-spring","stock":"b5-bravo-stock","upper_receiver":"aero-m4e1-enhanced-upper","barrel":"faxon-16-pencil-barrel","handguard":"aero-enhanced-15-handguard","gas_block":"bcm-625-gas-block","gas_tube":"aero-mid-gas-tube","muzzle":"a2-flash-hider","bolt_carrier_group":"aero-556-bcg","charging_handle":"radian-raptor-lt-charging-handle"},"mounts":{"optic":{"part":"eotech-exps3","host":"upper_receiver","interface":"top_rail","index":10},"magnifier":{"part":"eotech-g45","host":"upper_receiver","interface":"top_rail","index":3}},"params":{"stock_position":1},"finishes":{},"fitments":{"handguard":"enhanced"},"owned":[],"kits":["bcm-stock-kit"]},"ar57-16":{"version":11,"id":"ar57-16","name":"AR57 16 in, 5.7x28","platform":"ar15","parts":{"lower_receiver":"bad-workhorse-lower","lpk":"rise-lpk","trigger":"bcm-pnt-trigger","trigger_guard":"magpul-moe-trigger-guard","grip":"bcm-grip-mod-3","magazine":"fn-p90-50-magazine","receiver_extension":"bcm-receiver-extension","end_plate":"bcm-end-plate","castle_nut":"bcm-castle-nut","buffer":"panzer-ar57-buffer","buffer_spring":"bcm-carbine-action-spring","stock":"bcm-stock-mod-0","upper_receiver":"panzer-ar57-ult-16-upper"},"mounts":{"optic_mount":{"part":"holosun-aro-163-mount","host":"upper_receiver","interface":"top_rail","index":9},"optic":{"part":"holosun-aro","host":"optic_mount","interface":"deck","index":0}},"params":{"stock_position":1},"finishes":{},"fitments":{},"owned":[],"kits":["bcm-stock-kit","panzer-ar57-ult-16"]},"bcm-115-pistol-folding":{"version":11,"id":"bcm-115-pistol-folding","name":"BCM 11.5 in pistol on a Law GEN-S","platform":"ar15","parts":{"lower_receiver":"bad-workhorse-lower","lpk":"rise-lpk","trigger":"bcm-pnt-trigger","trigger_guard":"magpul-moe-trigger-guard","grip":"bcm-grip-mod-3","magazine":"magpul-pmag-30-gen-m3","folding_adapter":"law-tactical-gen-s-folder","receiver_extension":"bcm-receiver-extension","end_plate":"bcm-end-plate","castle_nut":"bcm-castle-nut","buffer":"bcm-carbine-buffer","buffer_spring":"bcm-carbine-action-spring","stock":"sb-tactical-sba4","upper_receiver":"bcm-m4-upper","barrel":"bcm-115-carbine-barrel","handguard":"bcm-mcmr-10-handguard","gas_block":"bcm-750-gas-block","gas_tube":"aero-carbine-gas-tube","muzzle":"surefire-socom-3-prong","bolt_carrier_group":"bcm-bcg","charging_handle":"bcm-mk2-charging-handle"},"mounts":{"optic_mount":{"part":"holosun-aro-163-mount","host":"upper_receiver","interface":"top_rail","index":8},"optic":{"part":"holosun-aro","host":"optic_mount","interface":"deck","index":0}},"params":{"stock_position":1},"finishes":{},"fitments":{},"owned":[],"kits":["bcm-stock-kit"]},"bcm-115-pistol":{"version":11,"id":"bcm-115-pistol","name":"BCM 11.5 in pistol, SBA3 brace","platform":"ar15","parts":{"lower_receiver":"bad-workhorse-lower","lpk":"rise-lpk","trigger":"bcm-pnt-trigger","trigger_guard":"magpul-moe-trigger-guard","grip":"bcm-grip-mod-3","magazine":"magpul-pmag-30-gen-m3","receiver_extension":"bcm-receiver-extension","end_plate":"bcm-end-plate","castle_nut":"bcm-castle-nut","buffer":"bcm-carbine-buffer","buffer_spring":"bcm-carbine-action-spring","stock":"sb-tactical-sba3","upper_receiver":"bcm-m4-upper","barrel":"bcm-115-carbine-barrel","handguard":"bcm-mcmr-10-handguard","gas_block":"bcm-750-gas-block","gas_tube":"aero-carbine-gas-tube","muzzle":"surefire-socom-3-prong","bolt_carrier_group":"bcm-bcg","charging_handle":"bcm-mk2-charging-handle"},"mounts":{"optic_mount":{"part":"holosun-aro-163-mount","host":"upper_receiver","interface":"top_rail","index":8},"optic":{"part":"holosun-aro","host":"optic_mount","interface":"deck","index":0}},"params":{"stock_position":1},"finishes":{},"fitments":{},"owned":[],"kits":["bcm-stock-kit"]},"bcm-115-suppressed":{"version":11,"id":"bcm-115-suppressed","name":"BCM 11.5 in carbine, suppressed","platform":"ar15","parts":{"lower_receiver":"bad-workhorse-lower","lpk":"rise-lpk","trigger":"bcm-pnt-trigger","trigger_guard":"magpul-moe-trigger-guard","grip":"bcm-grip-mod-3","magazine":"magpul-pmag-30-gen-m3","receiver_extension":"bcm-receiver-extension","end_plate":"bcm-end-plate","castle_nut":"bcm-castle-nut","buffer":"bcm-carbine-buffer","buffer_spring":"bcm-carbine-action-spring","stock":"bcm-stock-mod-0","upper_receiver":"bcm-m4-upper","barrel":"bcm-115-carbine-barrel","handguard":"bcm-mcmr-10-handguard","gas_block":"bcm-750-gas-block","gas_tube":"aero-carbine-gas-tube","muzzle":"surefire-socom-3-prong","suppressor":"surefire-socom556-rc2","bolt_carrier_group":"bcm-bcg","charging_handle":"bcm-mk2-charging-handle"},"mounts":{"optic_mount":{"part":"holosun-aro-163-mount","host":"upper_receiver","interface":"top_rail","index":8},"optic":{"part":"holosun-aro","host":"optic_mount","interface":"deck","index":0}},"params":{"stock_position":1},"finishes":{},"fitments":{},"owned":[],"kits":["bcm-stock-kit"]},"bcm-16-folding":{"version":11,"id":"bcm-16-folding","name":"BCM 16 in on a Law folder","platform":"ar15","parts":{"lower_receiver":"bad-workhorse-lower","lpk":"rise-lpk","trigger":"bcm-pnt-trigger","trigger_guard":"magpul-moe-trigger-guard","grip":"bcm-grip-mod-3","magazine":"magpul-pmag-30-gen-m3","folding_adapter":"law-tactical-gen3m-folder","receiver_extension":"bcm-receiver-extension","end_plate":"bcm-end-plate","castle_nut":"bcm-castle-nut","buffer":"bcm-carbine-buffer","buffer_spring":"bcm-carbine-action-spring","stock":"bcm-stock-mod-0","upper_receiver":"bcm-m4-upper","barrel":"bcm-16-mid-barrel","handguard":"bcm-mcmr-15-handguard","gas_block":"bcm-750-gas-block","gas_tube":"bcm-mid-gas-tube","muzzle":"a2-flash-hider","bolt_carrier_group":"bcm-bcg","charging_handle":"bcm-mk2-charging-handle"},"mounts":{"optic_mount":{"part":"holosun-aro-163-mount","host":"upper_receiver","interface":"top_rail","index":8},"optic":{"part":"holosun-aro","host":"optic_mount","interface":"deck","index":0}},"params":{"stock_position":1},"finishes":{},"fitments":{},"owned":[],"kits":["bcm-urg-mid-16-mcmr-15","bcm-stock-kit"]},"bcm-16-mid":{"version":11,"id":"bcm-16-mid","name":"BCM 16 in mid-length","platform":"ar15","parts":{"lower_receiver":"bad-workhorse-lower","lpk":"rise-lpk","trigger":"bcm-pnt-trigger","trigger_guard":"magpul-moe-trigger-guard","grip":"bcm-grip-mod-3","magazine":"magpul-pmag-30-gen-m3","receiver_extension":"bcm-receiver-extension","end_plate":"bcm-end-plate","castle_nut":"bcm-castle-nut","buffer":"bcm-carbine-buffer","buffer_spring":"bcm-carbine-action-spring","stock":"bcm-stock-mod-0","upper_receiver":"bcm-m4-upper","barrel":"bcm-16-mid-barrel","handguard":"bcm-mcmr-15-handguard","gas_block":"bcm-750-gas-block","gas_tube":"bcm-mid-gas-tube","muzzle":"a2-flash-hider","bolt_carrier_group":"bcm-bcg","charging_handle":"bcm-mk2-charging-handle"},"mounts":{"optic_mount":{"part":"holosun-aro-163-mount","host":"upper_receiver","interface":"top_rail","index":8},"optic":{"part":"holosun-aro","host":"optic_mount","interface":"deck","index":0}},"params":{"stock_position":1},"finishes":{},"fitments":{},"owned":[],"kits":["bcm-urg-mid-16-mcmr-15","bcm-stock-kit"]},"budget-16":{"version":11,"id":"budget-16","name":"Budget 16 in carbine","platform":"ar15","parts":{"lower_receiver":"bca-stripped-lower","lpk":"cmmg-lower-parts-kit","magazine":"magpul-pmag-30-gen-m3","receiver_extension":"bcm-receiver-extension","end_plate":"bcm-end-plate","castle_nut":"bcm-castle-nut","buffer":"bcm-carbine-buffer","buffer_spring":"bcm-carbine-action-spring","stock":"b5-bravo-stock","upper_receiver":"expo-arms-stripped-upper","barrel":"bca-556-16-mid-barrel","handguard":"expo-arms-mlok-15-handguard","gas_block":"aero-750-gas-block","gas_tube":"aero-mid-gas-tube","muzzle":"a2-flash-hider","bolt_carrier_group":"toolcraft-556-bcg","charging_handle":"aero-charging-handle"},"mounts":{"optic_mount":{"part":"sig-romeo-msr-riser-mount","host":"upper_receiver","interface":"top_rail","index":8},"optic":{"part":"sig-romeo-msr-gen-2","host":"optic_mount","interface":"deck","index":0}},"params":{"stock_position":1},"finishes":{},"fitments":{},"owned":[],"kits":["bcm-stock-kit"]},"carbine":{"version":11,"id":"carbine","name":"22RB carbine, scoped","platform":"ar15","parts":{"lower_receiver":"bad-workhorse-lower","upper_receiver":"nordic-22rb-upper","muzzle":"a2-flash-hider","receiver_extension":"bcm-receiver-extension","end_plate":"bcm-end-plate","castle_nut":"bcm-castle-nut","stock":"magpul-moe-carbine","grip":"magpul-moe-plus","trigger_guard":"magpul-moe-trigger-guard","trigger":"larue-mbt-2s","lpk":"rise-lpk","magazine":"blackdog-22lr-15"},"mounts":{"scope_mount":{"part":"sig-alpha-msr-30mm","host":"upper_receiver","interface":"top_rail","index":9},"optic":{"part":"sig-tango-msr-1-6x24","host":"scope_mount","interface":"rings","index":3}},"params":{"stock_position":3},"finishes":{"magazine.body":{"option":"smoke"}},"fitments":{},"owned":[],"kits":["bcm-stock-kit"]},"complete":{"version":11,"id":"complete","name":"22RB on a complete lower","platform":"ar15","parts":{"lower_receiver":"aero-m4e1-lower","upper_receiver":"nordic-22rb-upper","muzzle":"nordic-thread-protector","magazine":"blackdog-22lr-15"},"mounts":{"optic_mount":{"part":"holosun-aro-163-mount","host":"upper_receiver","interface":"top_rail","index":12},"optic":{"part":"holosun-aro","host":"optic_mount","interface":"deck","index":0},"magnifier":{"part":"holosun-hm3x","host":"upper_receiver","interface":"top_rail","index":2}},"params":{},"finishes":{"magazine.body":{"option":"smoke"}},"fitments":{},"owned":[],"kits":[]},"drop-in-16":{"version":11,"id":"drop-in-16","name":"Drop-in 16 in, Stealth Gray on BCM's MK2 lower","platform":"ar15","parts":{"lower_receiver":"bcm-mk2-lower-receiver","trigger":"bcm-pnt-trigger","grip":"bcm-grip-mod-4","magazine":"magpul-pmag-30-gen-m3","receiver_extension":"bcm-mk2-receiver-extension","end_plate":"bcm-qd-end-plate","castle_nut":"bcm-castle-nut","buffer":"bcm-mk2-buffer-t0","buffer_spring":"bcm-rifle-m16-action-spring","stock":"magpul-moe-sl-carbine","upper_receiver":"bcm-m4-upper","barrel":"bcm-16-mid-barrel","barrel_nut":"bcm-gi-barrel-nut","delta_ring":"bcm-delta-ring-assembly","handguard":"magpul-moe-mlok-handguard-mid","gas_block":"bcm-front-sight-base-f-750","front_sight_post":"aero-ar15-front-sight-post-kit","handguard_cap":"bcm-handguard-cap-round-750","gas_tube":"bcm-mid-gas-tube","muzzle":"a2-flash-hider","bolt_carrier_group":"bcm-bcg","charging_handle":"bcm-mk2-charging-handle"},"mounts":{"optic_mount":{"part":"aimpoint-micro-lrp-39mm","host":"upper_receiver","interface":"top_rail","index":8},"optic":{"part":"aimpoint-micro-t-2","host":"optic_mount","interface":"deck","index":0},"backup_sight":{"part":"magpul-mbus-3-rear","host":"upper_receiver","interface":"top_rail","index":0,"folded":true},"hand_stop":{"part":"magpul-mlok-hand-stop","host":"handguard","interface":"mlok_bottom","index":2,"face":"bottom"}},"params":{"stock_position":1},"finishes":{"handguard.body":{"option":"gry"},"stock.body":{"option":"sgy"},"hand_stop.body":{"option":"sgy"}},"fitments":{},"owned":[],"kits":["bcm-mk2-lower-no-stock"]},"suppressed":{"version":11,"id":"suppressed","name":"22RB suppressed, FDE","platform":"ar15","parts":{"lower_receiver":"bad-workhorse-lower","upper_receiver":"nordic-22rb-upper","muzzle":"silencerco-sparrow-22","receiver_extension":"bcm-receiver-extension","end_plate":"bcm-end-plate","castle_nut":"bcm-castle-nut","stock":"magpul-ctr","grip":"magpul-moe-plus","trigger_guard":"magpul-moe-trigger-guard","trigger":"larue-mbt-2s","lpk":"rise-lpk","magazine":"blackdog-22lr-25"},"mounts":{"scope_mount":{"part":"sig-alpha-msr-30mm","host":"upper_receiver","interface":"top_rail","index":9},"optic":{"part":"sig-tango-msr-1-6x24","host":"scope_mount","interface":"rings","index":3}},"params":{"stock_position":4},"finishes":{"stock.body":{"option":"fde"},"grip.body":{"option":"fde"},"trigger_guard.body":{"option":"fde"},"optic.body":{"option":"coyote"},"scope_mount.body":{"option":"coyote"},"magazine.body":{"option":"black"}},"fitments":{},"owned":[],"kits":["bcm-stock-kit"]},"two-tone-16":{"version":11,"id":"two-tone-16","name":"Two-tone 16 in, Stealth Gray and soft-shooting","platform":"ar15","parts":{"lower_receiver":"geissele-super-duty-stripped-lower","lpk":"rise-lpk","trigger":"geissele-ssa-e","trigger_guard":"magpul-moe-trigger-guard","grip":"magpul-moe-k2-plus","magazine":"hexmag-series-2-ar15-30","receiver_extension":"vltor-a5-receiver-extension","end_plate":"vltor-lockplate","castle_nut":"vltor-castle-nut","buffer":"vltor-a5h2-buffer","buffer_spring":"vltor-a5-buffer-spring","stock":"magpul-moe-sl-carbine","upper_receiver":"geissele-super-duty-stripped-upper","barrel":"geissele-16-chf-barrel","handguard":"mas-defense-nero-15-handguard","gas_block":"slr-sentry-7-gas-block","gas_tube":"aero-mid-gas-tube","muzzle":"precision-armament-m4-72","bolt_carrier_group":"bcm-bcg","charging_handle":"radian-raptor-charging-handle"},"mounts":{"optic_mount":{"part":"aimpoint-micro-lrp-39mm","host":"upper_receiver","interface":"top_rail","index":9},"optic":{"part":"aimpoint-micro-t-2","host":"optic_mount","interface":"deck","index":0},"hand_stop":{"part":"magpul-mlok-hand-stop","host":"handguard","interface":"mlok","index":5,"face":"bottom"}},"params":{"stock_position":1},"finishes":{"trigger_guard.body":{"option":"sgy"},"grip.body":{"option":"sgy"},"stock.body":{"option":"sgy"},"hand_stop.body":{"option":"sgy"},"magazine.body":{"option":"gray"}},"fitments":{},"owned":[],"kits":["geissele-super-duty-receiver-set","vltor-a5-buffer-kit"]},"tx22-toro":{"version":11,"id":"tx22-toro","name":"Taurus TX22 T.O.R.O.","platform":"taurus-tx22","parts":{"frame":"taurus-tx22-frame","slide":"taurus-tx22-toro-slide","barrel":"taurus-tx22-barrel-46","muzzle":"taurus-tx22-thread-protector","magazine":"taurus-tx22-magazine-16"},"mounts":{},"params":{},"finishes":{},"fitments":{},"owned":[],"kits":["taurus-tx22-toro"]},"v1":{"version":11,"id":"v1","name":"22RB .22 LR rifle","platform":"ar15","parts":{"lower_receiver":"bad-workhorse-lower","upper_receiver":"nordic-22rb-upper","muzzle":"nordic-thread-protector","receiver_extension":"bcm-receiver-extension","end_plate":"bcm-end-plate","castle_nut":"bcm-castle-nut","stock":"magpul-moe-sl-carbine","grip":"magpul-moe-k2-plus","trigger_guard":"magpul-moe-trigger-guard","trigger":"larue-mbt-2s","lpk":"rise-lpk","magazine":"blackdog-22lr-15"},"mounts":{"optic_mount":{"part":"holosun-aro-163-mount","host":"upper_receiver","interface":"top_rail","index":12},"optic":{"part":"holosun-aro","host":"optic_mount","interface":"deck","index":0},"magnifier":{"part":"holosun-hm3x","host":"upper_receiver","interface":"top_rail","index":2}},"params":{"stock_position":1},"finishes":{"magazine.body":{"option":"smoke"}},"fitments":{},"owned":[],"kits":["bcm-stock-kit"]}},"presets":{"aero-16-light":{"summary":"Aero's M4E1 stripped lower and threaded upper under its slick-topped 15 in S-ONE, Faxon's 16 in pencil barrel with BCM's .625 gas block, MFT's Minimalist stock, a PMAG 20, and Primary Arms' SLx 1-6x24 in its Deluxe mount.","order":11},"aero-556-fitted":{"summary":"The Aero 5.56 carbine with what gets hung on one, Magpul's MBUS Pro sights folded under the red dot, a SureFire Scout Light Pro on the handguard's right and a QD sling mount on its left.","order":6},"aero-556":{"summary":"A 5.56 NATO carbine from Aero Precision's components on its M4E1 complete lower, a 16 in mid-length barrel under the 15 in R-ONE, a red dot and a PMAG.","order":5},"aero-m4e1-pencil":{"summary":"Aero's M4E1 stripped lower and Enhanced upper under the Enhanced handguard made for it, Faxon's 16 in pencil barrel with BCM's .625 gas block, Radian's Talon selector and Raptor-LT, and an EXPS3 with the G45 behind it.","order":10},"ar57-16":{"summary":"Panzer Arms' AR57 16 in upper, fed from FN's 50-round P90 magazine laid along its top and sold with the heavier buffer it needs, on the BCM build's lower, whose magazine well is left empty for the cases to drop through; a red dot on its receiver's rail.","order":13},"bcm-115-pistol-folding":{"summary":"BCM's 11.5 in barrel and 10 in MCMR handguard with SB Tactical's SBA4 brace on Law Tactical's GEN-S folding adapter; Fold, on the toolbar, swings the brace to the left and says how short the pistol gets.","order":15},"bcm-115-pistol":{"summary":"BCM's 11.5 in barrel under its 10 in MCMR handguard with SB Tactical's SBA3 brace where a stock would go; its figures say what federal law makes of it, and what changes if its lower was first built as a rifle.","order":14},"bcm-115-suppressed":{"summary":"BCM's 11.5 in carbine-gas barrel under its 10 in MCMR handguard, with SureFire's SOCOM556-RC2 suppressor locked onto its 3-prong flash hider, on the lower of the BCM 16 in build.","order":9},"bcm-16-folding":{"summary":"BCM's 16 in mid-length build with Law Tactical's Gen 3-M folding stock adapter between its lower and its buffer tube; Fold, on the toolbar, swings the stock to the left and says how far it goes and what the rifle then measures.","order":12},"bcm-16-mid":{"summary":"BCM's complete 16 in mid-length upper under its 15 in MCMR handguard, with its carrier and MK2 charging handle, on a stripped lower built up with BCM's PNT trigger, Grip Mod 3 and Stock Mod 0.","order":7},"budget-16":{"summary":"A budget 16 in 5.56 carbine of Bear Creek's barrel and lower, Expo Arms' upper and handguard, a Toolcraft carrier, CMMG's parts kit with its trigger and grip, B5's Bravo stock and SIG's ROMEO-MSR red dot; the stripped upper's forward assist and port cover are still to buy.","order":8},"carbine":{"summary":"The same rifle as a plain carbine, with a 1-6x scope, the MOE Carbine stock two steps out, the MOE+ grip and an A2 flash hider.","order":2},"complete":{"summary":"Aero's M4E1 complete lower, sold with its grip, stock and fire control, under the same upper and sights.","order":4},"drop-in-16":{"summary":"BCM's MK2 complete lower and its recoil system under a BCM upper on its 16 in mid-length barrel, with Magpul's MOE M-LOK drop-in hand guard and MOE SL stock in Stealth Gray, a forged front sight base and a folding rear sight under an Aimpoint.","order":17},"suppressed":{"summary":"A Sparrow 22 on the muzzle and a 25-round magazine, with the CTR stock, FDE furniture and the scope in coyote.","order":3},"two-tone-16":{"summary":"Geissele's Super Duty receivers in black on its 16 in mid-length barrel under MAS Defense's 15 in NERO in Stealth Gray, Magpul's MOE SL stock, K2+ grip, trigger guard and hand stop in Stealth Gray, Hexmag's Series 2 magazine in gray, VLTOR's A5 buffer system, SLR's adjustable Sentry gas block and Precision Armament's M4-72.","order":16},"tx22-toro":{"summary":"Taurus's TX22 .22 LR pistol in its optics-ready T.O.R.O. form, as it comes from the box, with the cut in its slide for a red dot under its cover plate and its threaded barrel's protector on.","order":20},"v1":{"summary":"A .22 LR rifle on the Nordic 22RB upper, with a red dot ahead of a magnifier, the MOE SL stock and the K2+ grip.","order":1}},"categories":{"adapter_plate":{"category":"adapter_plate","label":"Adapter plate","about":"A plate that goes between the handguard and the accessories made to bolt through it.","mounts":true,"sight":false,"holds_sight":false,"inside":false,"ffl":false,"under":true,"dimensions":{"length":{"label":"Overall length (along the handguard)","kind":"length","required":true,"how":"Manufacturer spec table; a plan view scaled by what is known along it (its own holes at the M-LOK interval, the slots it covers at the slot pitch) checks it."},"height":{"label":"Thickness under what it carries (how far it stands them off the handguard's face)","kind":"length","required":true,"how":"The plate's thickness where an accessory bears on it, from a side view scaled by the length. Say what it is measured between."},"width":{"label":"Width (side to side, at its widest)","kind":"length","required":true,"how":"Manufacturer spec table; a plan view scaled by the length checks it."},"end_width":{"label":"Width where an accessory sits on it","kind":"length","required":false,"how":"A plan view scaled by the length: the plate across, at one of its places. Against the accessory's own width it says whether the accessory overhangs the plate."},"land_width":{"label":"Width of the flat an accessory bears on","kind":"length","required":false,"how":"A plan view scaled by the length: the flat between the plate's bevels at one of its places. Against the band an accessory bears by (its width between its ears) it says whether the flat lies between the ears."},"weight":{"label":"Weight","kind":"mass","required":true,"how":"Manufacturer spec table, for the plate alone."},"lugs":{"label":"M-LOK slots it covers","kind":"count","required":true,"how":"How many of the handguard's slots lie under it: its length against the slot pitch, and the maker's pictures of it installed. The interface's `lugs` reads it: a plate at slot n takes n and the next lugs - 1."},"positions":{"label":"Places it has for what it carries","kind":"count","required":true,"how":"How many accessories bolt through it, each at its own place: the maker's instruction sheet."},"position_pitch":{"label":"Distance between those places","kind":"length","required":true,"how":"Between the centres of two neighbouring places (each the middle of its pair of screw holes), from a plan view scaled by the length; a multiple of the M-LOK slot pitch when each place is over a slot."},"position_x":{"label":"Rear place's centre ahead of the plate's rear end","kind":"length","required":true,"how":"A plan view scaled by the length: the middle of the rear pair of screw holes, as a same-plane ratio against the plate's ends. It is over the centre of the rearmost slot the plate covers: the `lug` anchor is there."},"reach_inside":{"label":"Reach inside the handguard (below the mounting face)","kind":"length","required":false,"how":"What of the plate itself stands in a slot or inside the handguard. The screws and T-nuts are the carried accessories'."},"carried_reach_inside":{"label":"Room under an accessory it carries (for its screws and T-nut)","kind":"length","required":false,"how":"How far an accessory's hardware may reach below the plate's own top face: the plate's thickness and whatever room the hand guard under it has. A figure only where the maker gives one."}},"part":{"anchors":{"lug":{"origin":["{.position_x}",0,0],"note":"The centre of the rearmost slot it covers, on its mounting face: what an M-LOK position places (a plate at slot n lies over n and the slots ahead of it). Adapter plate frame: origin at the plate's rear end on the mounting face (the surface that bears on the handguard), +x forward along the handguard, +y out of the face (away from the handguard: the solver turns it to the face it is on)."},"plate":{"origin":["{.position_x}","{.height}",0],"note":"The centre of its rear place on the face an accessory bears on: where what it carries is put, a place further forward for each index."}},"interfaces":{"mlok":{"type":"mlok","role":"accessory","anchor":"lug","params":{"lugs":"={.lugs}","reach_inside":"={.reach_inside}","in_slot":true},"flips":false,"note":"`in_slot`: its places are over the handguard's slots, so it sits at the slots themselves and never between two. `lugs` is the slots it covers."},"carries":{"type":"mlok","role":"slots","anchor":"plate","params":{"pitch":"={.position_pitch}","slots":"={.positions}","reach_inside":"={.carried_reach_inside}"},"flips":false,"note":"What it carries is mounted here: an M-LOK accessory, at one of its places. Name the parts it is made for under `only`, with the maker's sentence."}},"materials":{"body":{"label":"Adapter plate","finish":"polymer","recolorable":true,"color":"placeholder-polymer-black"}}},"calibration":[{"feature":"known-length","note":"Its own screw holes at the M-LOK interval, and its places at the slot pitch: a scale and a check along it"},{"feature":"lineup","note":"Laid out beside the accessories it carries, whose sizes are in the ledger: on one flat surface they fix the plane of an oblique photo"},{"feature":"drawing","note":"The maker's instruction sheet, for how it goes on and what it replaces"}]},"backup_sight":{"category":"backup_sight","label":"Backup sight","about":"Iron sights for the rail, a front and a rear. Many fold flat until they are needed.","mounts":true,"sight":true,"holds_sight":false,"inside":false,"ffl":false,"under":false,"dimensions":{"weight":{"label":"Weight","kind":"mass","required":true,"how":"Manufacturer spec table."},"length":{"label":"Length along the rail (folded, where it folds)","kind":"length","required":true,"how":"Manufacturer spec table (\"stowed length\"); a straight side view scaled by a published size checks it."},"width":{"label":"Width","kind":"length","required":true,"how":"Manufacturer spec table."},"height":{"label":"Height above the rail's top, folded (a fixed sight: its height)","kind":"length","required":true,"how":"Manufacturer spec table (\"stowed height\"): say whether it is measured from the rail's top or includes the clamp below it."},"height_up":{"label":"Height above the rail's top, standing","kind":"length","required":false,"how":"The maker's figure or drawing for the sight deployed, to its highest point; failing that, a straight side view of it standing, scaled by a published size."},"sight_line_above_rail":{"label":"Sight line above the rail's top (the aperture's centre, the post's tip)","kind":"length","required":true,"how":"The maker's figure: say what it is measured to. The `optical_axis` anchor is here, and the readouts list it beside the optic's axis."},"clamp_length":{"label":"Clamp's length along the rail","kind":"length","required":false,"how":"A straight side view scaled by a published size: the base's two ends. `clamp_rear` and `clamp_front` read it (half each way about the frame's origin)."}},"part":{"anchors":{"rail_clamp":{"origin":[0,0,0],"note":"Backup sight frame: on the rail's top surface at the middle of its clamp, +x toward the muzzle, +y up."},"optical_axis":{"origin":[0,"{.sight_line_above_rail}",0],"note":"The sight line it has standing: the aperture's centre, or the post's tip."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{},"flips":false,"note":"Add params `clamp_rear` and `clamp_front`: how far its clamp reaches behind and ahead of the anchor, as ledger expressions. And `start: rear` or `start: front` where its maker says which end of the rail it goes on, with the sentence."},"sight_line":{"type":"optic.sight_line","role":"irons","params":{"magnification":"1x"},"flips":false,"note":"An iron sight: it doesn't magnify, and nothing is checked against it (data/interfaces.yaml)."}},"materials":{"body":{"label":"Sight","finish":"polymer","recolorable":false,"color":"placeholder-polymer-black"}}},"calibration":[{"feature":"known-length","note":"Two published sizes on a straight side view of it folded (they must agree)"},{"feature":"picatinny","note":"On a rail, straight side on: the slots give the scale in the clamp's plane"},{"feature":"drawing","note":"A design patent's elevations (folded and standing), each figure scaled by published sizes"}]},"barrel":{"category":"barrel","label":"Barrel","about":"The barrel sets what the rifle fires and much of its length, its weight and its balance. It is chosen by its cartridge, its length and the length of its gas system.","mounts":false,"sight":false,"holds_sight":false,"inside":false,"ffl":false,"under":false,"dimensions":{"weight":{"label":"Weight","kind":"mass","required":true,"how":"Manufacturer spec table."},"length":{"label":"Length from the extension's face to the muzzle","kind":"length","required":true,"how":"Maker's figure (the nominal 16 in is to the muzzle face; say whether a pinned device counts)."},"shoulder_x":{"label":"The muzzle shoulder ahead of the extension's face","kind":"length","required":true,"how":"Length less the thread length; a muzzle device seats here."},"thread_length":{"label":"The muzzle thread's length","kind":"length","required":true,"how":"Maker's figure or a drawing."},"gas_port_x":{"label":"The gas port ahead of the extension's face","kind":"length","required":true,"how":"Maker's figure (carbine, mid, rifle) or a drawing; the gas block seats here."},"journal_od":{"label":"The gas block journal's diameter (.750 or .625)","kind":"length","required":true,"how":"Maker's figure."},"muzzle_od":{"label":"The diameter behind the muzzle thread","kind":"length","required":true,"how":"Maker's profile drawing or a photo scaled in the barrel's plane."}},"part":{"cartridge":{"takes":["unstated"],"stated":"unstated","source":"unstated"},"anchors":{"extension":{"origin":[0,0,0],"note":"The barrel extension's face on the bore axis, +x toward the muzzle."},"muzzle":{"origin":["{.shoulder_x}",0,0]},"gas_journal":{"origin":["{.gas_port_x}",0,0]}},"interfaces":{"barrel_extension":{"type":"ar15.barrel_extension","role":"barrel","anchor":"extension","params":{},"flips":false},"muzzle":{"type":"muzzle_thread","role":"barrel","anchor":"muzzle","params":{"thread":"unstated","thread_length":"={.thread_length}"},"flips":false},"gas_journal":{"type":"ar15.gas_journal","role":"barrel","anchor":"gas_journal","params":{"journal_od":"={.journal_od}"},"flips":false},"gas_system":{"type":"ar15.gas_system","role":"barrel","params":{"length":"unstated"},"flips":false}},"materials":{"barrel":{"label":"Barrel","finish":"steel","recolorable":false,"color":"placeholder-black"}}},"calibration":[{"feature":"known-length","note":"The published length between the extension's face and the muzzle; a turned part's radii from its silhouette (tools/turned.py)."}]},"barrel_nut":{"category":"barrel_nut","label":"Barrel nut","about":"The nut that threads onto the front of the upper receiver and holds the barrel in it. A free-float handguard brings its own; a drop-in handguard sits in a delta ring on this one.","mounts":false,"sight":false,"holds_sight":false,"inside":false,"ffl":false,"under":false,"dimensions":{"weight":{"label":"Weight","kind":"mass","required":true,"how":"Maker's or seller's figure; else its steel, by its sizes and std.density.steel."},"length":{"label":"Length along the bore","kind":"length","required":true,"how":"Maker's figure, or a side photo scaled by the receiver's thread."},"flange_diameter":{"label":"Its toothed flange's outside diameter","kind":"length","required":true,"how":"An end-on photo scaled by the thread (std.ar15.barrel_nut_thread) or a seller's figure."}},"part":{"anchors":{"mount":{"origin":[0,0,0],"note":"Part frame: the receiver's front face on the bore axis, +x toward the muzzle."}},"interfaces":{"handguard_mount":{"type":"ar15.handguard_mount","role":"handguard","anchor":"mount","params":{"nut":"standard"},"flips":false},"delta_ring":{"type":"ar15.delta_ring","role":"nut","anchor":"mount","params":{},"flips":false},"drop_in":{"type":"ar15.drop_in","role":"nut","params":{},"flips":false}},"materials":{"nut":{"label":"Barrel nut","finish":"phosphate","recolorable":false,"color":"placeholder-black"}}},"calibration":[]},"bolt_carrier_group":{"category":"bolt_carrier_group","label":"Bolt carrier group","about":"The parts that move: the bolt that locks into the barrel, and the carrier that works it at each shot. It is chosen for the cartridge and by its finish.","mounts":false,"sight":false,"holds_sight":false,"inside":true,"ffl":false,"under":false,"dimensions":{"weight":{"label":"Weight","kind":"mass","required":true,"how":"Manufacturer spec table."},"length":{"label":"Length","kind":"length","required":true,"how":"The Army's drawings (bolt carrier assembly 8448501, 12011849) or the maker's figure."},"od":{"label":"The carrier's diameter","kind":"length","required":true,"how":"The Army's drawings."}},"part":{"cartridge":{"takes":["unstated"],"stated":"unstated","source":"unstated"},"anchors":{"channel":{"origin":[0,0,0],"note":"The receiver's rear face on the bore axis, +x toward the muzzle."}},"interfaces":{"carrier_channel":{"type":"ar15.carrier_channel","role":"carrier","anchor":"channel","params":{},"flips":false}},"materials":{"body":{"label":"Carrier","finish":"steel","recolorable":false,"color":"placeholder-black"}}},"calibration":[]},"brace":{"category":"brace","label":"Brace","about":"What an AR pistol has where a rifle has its stock: it slides onto the receiver extension and is made to rest against or strap to the forearm. What federal law makes of a build with one is said in the build's figures.","mounts":false,"sight":false,"holds_sight":false,"inside":false,"ffl":false,"under":false,"shortest":["charging_handle","end_plate"],"dimensions":{"length":{"label":"Overall length","kind":"length","required":true,"how":"Manufacturer page. With the height, it scales a straight side photo and checks that the photo is straight (the two scales must agree)."},"height":{"label":"Height","kind":"length","required":true,"how":"Manufacturer page."},"width":{"label":"Width","kind":"length","required":true,"how":"Manufacturer page: the widest point, and what an end section (a design patent's end view) is scaled by."},"weight":{"label":"Weight","kind":"mass","required":true,"how":"Manufacturer spec table."},"tube_axis_below_top":{"label":"Tube axis below the brace's top edge","kind":"length","required":true,"how":"The exposed tube in a photo of the stock on a rifle: its axis midway between its limbs, below the stock's top. Scale that photo by the stock's own length or a rail in it, not by the tube's width (a black tube reads 3% thin on white), and allow for the photo's tilt. A design patent's end view draws the bore as a hidden-line circle: fit a circle, as a check."},"butt_behind_pin_pos1":{"label":"Rear behind the takedown pin at its first position (all the way forward), on the tube it is made for","kind":"length","required":true,"how":"A pin-framed side photo of the stock on a rifle, at any position: fit the traced outline into it (trace.py `register`), count its steps back from where its front would meet the castle nut, and take them off. Then check it: the stock's front must not pass the castle nut, and the tube's front hole less where the stock's lock pin stands should agree. The maker's lengths of pull against another stock's are a check only: Magpul's have moved 0.4 in between revisions, and seated the MOE Carbine inside the nut (M6)."}},"part":{"anchors":{"butt":{"origin":[0,0,0],"note":"The brace's rearmost plane on the tube axis: the part frame's origin. The overall length ends here, as it does at a stock's butt (ATF's handbook, 2.1.4: \"the rearmost portion of the weapon\")."},"tube":{"origin":["{.butt_behind_pin_pos1}",0,0],"x":[-1,0,0],"note":"Brace frame: origin on the tube axis in the plane of its rear, +x forward. At its first position this anchor sits at the takedown pin's X."}},"interfaces":{"tube":{"type":"receiver_extension","role":"stock","anchor":"tube","params":{"profile":"unstated"},"flips":false,"note":"Set the profile from the product's page (a mil-spec or commercial carbine tube, or the pistol tube it comes with). A body sold for both is one part with `fitments` (D28)."}},"materials":{"body":{"label":"Brace body","finish":"polymer","recolorable":true,"color":"placeholder-polymer-black"}}},"calibration":[{"feature":"known-length","note":"Published length and height on a straight side view: two scales that must agree (trace.py `dims`)"},{"feature":"patent","note":"A design patent's end and plan views, each scaled by the published sizes (D26)"},{"feature":"frame","note":"On a rifle with its pins in view: the seat (at any position: count the steps), and a check of the size. A Picatinny rail in the same photo checks the pins' scale"}]},"buffer":{"category":"buffer","label":"Buffer","about":"The weight inside the receiver extension that the bolt carrier pushes back against. Heavier and lighter ones change how the rifle cycles.","mounts":false,"sight":false,"holds_sight":false,"inside":true,"ffl":false,"under":false,"dimensions":{"weight":{"label":"Weight (its class: carbine, H, H2…)","kind":"mass","required":true,"how":"The Army's drawing (buffer assembly 8448615) for the standard; the maker's figure."},"length":{"label":"Length","kind":"length","required":true,"how":"The Army's drawing (8448615)."},"od":{"label":"Diameter","kind":"length","required":true,"how":"The Army's drawing."}},"part":{"anchors":{"bore":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the buffer's axis at its head's front face, +x rearward (toward its bumper)."}},"interfaces":{"bore":{"type":"ar15.extension_bore","role":"buffer","anchor":"bore","params":{},"flips":false}},"materials":{"body":{"label":"Buffer","finish":"anodized","recolorable":false,"color":"placeholder-black"}}},"calibration":[]},"buffer_spring":{"category":"buffer_spring","label":"Buffer spring","about":"The spring inside the receiver extension that sends the bolt carrier forward again after each shot.","mounts":false,"sight":false,"holds_sight":false,"inside":true,"ffl":false,"under":false,"dimensions":{"weight":{"label":"Weight","kind":"mass","required":true,"how":"Maker's figure."},"free_length":{"label":"Free length","kind":"length","required":true,"how":"The Army's drawing of the rifle's (8448629) says how it is made; a carbine's free length is the maker's figure or the standard's (std.carbine_action_spring.free_length)."}},"part":{"anchors":{"bore":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the receiver extension's axis where a buffer's front face rests, +x rearward: the spring is drawn as installed, from the buffer's seat to the tube's rear wall."}},"interfaces":{"bore":{"type":"ar15.extension_bore","role":"buffer","anchor":"bore","params":{},"flips":false}},"materials":{"spring":{"label":"Spring","finish":"steel","recolorable":false,"color":"placeholder-black"}}},"calibration":[]},"castle_nut":{"category":"castle_nut","label":"Castle nut","about":"The nut that locks the receiver extension to the lower receiver.","mounts":false,"sight":false,"holds_sight":false,"inside":false,"ffl":false,"under":false,"dimensions":{"od":{"label":"Outside diameter","kind":"length","required":true,"how":"Maker's figure or a drawing."},"thickness":{"label":"Thickness","kind":"length","required":true},"notches":{"label":"Notches on its rear face","kind":"count","required":false}},"part":{"anchors":{"seat":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the tube axis at the nut's front face, which bears on the end plate, +x rearward."}},"interfaces":{"nut_seat":{"type":"ar15.end_plate_seat","role":"nut","anchor":"seat","params":{},"flips":false}},"materials":{"nut":{"label":"Castle nut","finish":"steel","recolorable":false,"color":"placeholder-black"}}},"calibration":[]},"charging_handle":{"category":"charging_handle","label":"Charging handle","about":"The handle at the back of the upper that is pulled to work the bolt by hand. They differ in the size and the shape of their latches.","mounts":false,"sight":false,"holds_sight":false,"inside":false,"ffl":false,"under":false,"dimensions":{"weight":{"label":"Weight","kind":"mass","required":true,"how":"Manufacturer spec table."},"length":{"label":"Length","kind":"length","required":true,"how":"The Army's drawing (8448518) or the maker's figure."},"latch_reach":{"label":"The latch's reach beyond the receiver's side","kind":"length","required":true,"how":"Maker's figure or a plan view."}},"part":{"anchors":{"channel":{"origin":[0,0,0],"note":"Its T's shoulder on the channel's axis, +x toward the muzzle: what stops on the front wall of the receiver's open notch under its rail's rear end (the receiver's handle_seat_x). The T stands behind it, astride the receiver's rear face (2026-10-05: with the anchor at the receiver's rear face a handle hung 0.7 in behind where it stops)."}},"interfaces":{"charging_handle_channel":{"type":"ar15.charging_handle_channel","role":"handle","anchor":"channel","params":{},"flips":false}},"materials":{"body":{"label":"Charging handle","finish":"anodized","recolorable":false,"color":"placeholder-black"}}},"calibration":[]},"delta_ring":{"category":"delta_ring","label":"Delta ring","about":"The spring-loaded ring at the front of the upper receiver that holds the rear of a drop-in handguard. Pulled back, it lets the two halves of the handguard out.","mounts":false,"sight":false,"holds_sight":false,"inside":false,"ffl":false,"under":false,"dimensions":{"weight":{"label":"Weight","kind":"mass","required":true,"how":"Maker's or seller's figure; else its metal, by its sizes and its density."},"outside_diameter":{"label":"Outside diameter","kind":"length","required":true,"how":"Maker's figure, or a photo scaled by the receiver."},"length":{"label":"Length along the bore","kind":"length","required":true,"how":"A side photo scaled by a known size."}},"part":{"anchors":{"seat":{"origin":[0,0,0],"note":"Part frame: the receiver's front face on the bore axis, +x toward the muzzle."}},"interfaces":{"delta_ring":{"type":"ar15.delta_ring","role":"ring","anchor":"seat","params":{},"flips":false},"drop_in":{"type":"ar15.drop_in","role":"ring","params":{},"flips":false}},"materials":{"ring":{"label":"Delta ring","finish":"anodized","recolorable":false,"color":"placeholder-black"}}},"calibration":[]},"end_plate":{"category":"end_plate","label":"End plate","about":"The plate between the receiver extension's nut and the lower receiver. Some carry a place for a sling.","mounts":false,"sight":false,"holds_sight":false,"inside":false,"ffl":false,"under":false,"dimensions":{"thickness":{"label":"Thickness","kind":"length","required":true,"how":"Maker's figure or a drawing."},"height":{"label":"Height","kind":"length","required":true,"how":"A face-on photo scaled by a known size."}},"part":{"anchors":{"end":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the tube axis at the plate's front face, which bears on the receiver's rear face, +x rearward."},"nut_seat":{"origin":["{.thickness}",0,0],"x":[1,0,0],"note":"The plate's rear face, where the castle nut bears."}},"interfaces":{"extension_end":{"type":"ar15.extension_end","role":"fitting","anchor":"end","params":{},"flips":false},"nut_seat":{"type":"ar15.end_plate_seat","role":"plate","anchor":"nut_seat","params":{},"flips":false}},"materials":{"plate":{"label":"End plate","finish":"steel","recolorable":false,"color":"placeholder-black"}}},"calibration":[]},"folding_adapter":{"category":"folding_adapter","label":"Folding stock adapter","about":"A hinge between the lower receiver and the buffer tube: the tube and the stock swing to the side of the rifle, so it is shorter to carry and to store. The tube moves back by the adapter's length.","mounts":false,"sight":false,"holds_sight":false,"inside":false,"ffl":false,"under":false,"dimensions":{"weight":{"label":"Weight","kind":"mass","required":true,"how":"Maker's or a seller's spec table (what is in the box, said which)."},"added_length":{"label":"How far it moves the receiver extension back","kind":"length","required":true,"how":"The maker's \"adds ... to the length of pull\"; check it on a side photo against the receiver's pins."},"hinge_x":{"label":"The hinge's axis behind the takedown pin","kind":"length","required":true,"how":"A photo from above or below, folded and open, scaled by the receiver or the tube in its own plane."},"hinge_z":{"label":"The hinge's axis out from the tube's axis, toward the side it folds to","kind":"length","required":true,"how":"A photo from above or below, or from behind, scaled by the tube's diameter."},"fold_max":{"label":"How far the hinge turns before its own halves stop it","kind":"angle","required":true,"how":"A photo of it folded with nothing in the way, from above; or the maker's figure."},"length":{"label":"Its length along the bore","kind":"length","required":true,"how":"A side photo scaled by the receiver's pins, or a maker's figure."},"width":{"label":"Its width across the rifle, the hinge included","kind":"length","required":true,"how":"A photo from above or behind, scaled by the tube's diameter."},"height":{"label":"Its height","kind":"length","required":true,"how":"A side photo scaled by the tube's diameter."}},"part":{"anchors":{"receiver_thread":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the tube axis at the takedown pin's X, +x rearward (+z is then the rifle's left)."},"tube_socket":{"origin":["{.added_length}",0,0],"x":[1,0,0],"note":"Where a receiver extension's own frame stands with the adapter on: the takedown pin's X moved back by the adapter's length."},"hinge":{"origin":["{.hinge_x}",0,"{.hinge_z}"],"x":[1,0,0],"y":[0,1,0],"note":"On the hinge's axis; its y is the axis (the stock folds about it to `folding.side`)."}},"interfaces":{"receiver_thread":{"type":"ar15.buffer_tube_mount","role":"tube","anchor":"receiver_thread","params":{},"flips":false},"tube_socket":{"type":"ar15.buffer_tube_mount","role":"receiver","anchor":"tube_socket","params":{},"flips":false}},"materials":{"body":{"label":"Adapter","finish":"steel","recolorable":false,"color":"placeholder-black"}}},"calibration":[{"feature":"frame","note":"A photo of it on a lower with the pins in frame; from above for the hinge, folded and open."}]},"front_sight_post":{"category":"front_sight_post","label":"Front sight post","about":"The post in a front sight base that the eye lines up on through the rear sight. It screws in, and its height sets the elevation.","mounts":false,"sight":false,"holds_sight":false,"inside":false,"ffl":false,"under":false,"dimensions":{"weight":{"label":"Weight","kind":"mass","required":true,"how":"Maker's or seller's figure; else its steel."},"height":{"label":"Height above the tower's top","kind":"length","required":true,"how":"A side photo scaled by the base."}},"part":{"anchors":{"seat":{"origin":[0,0,0],"note":"Part frame: on the post's axis at the top of the base's tower, +x toward the muzzle, +y up."}},"interfaces":{"front_sight_post":{"type":"ar15.front_sight_post","role":"post","anchor":"seat","params":{},"flips":false}},"materials":{"post":{"label":"Post","finish":"phosphate","recolorable":false,"color":"placeholder-black"}}},"calibration":[]},"gas_block":{"category":"gas_block","label":"Gas block","about":"It sits on the barrel over the gas port and sends the gas into the gas tube. It comes in the diameters barrels are made in.","mounts":false,"sight":false,"holds_sight":false,"inside":false,"ffl":false,"under":false,"section":{"height_above_bore":"out"},"dimensions":{"weight":{"label":"Weight","kind":"mass","required":true,"how":"Manufacturer spec table."},"journal_id":{"label":"Bore (the journal it fits: .750 or .625)","kind":"length","required":true,"how":"Maker's figure."},"length":{"label":"Length along the barrel","kind":"length","required":true,"how":"Maker's figure."},"height_above_bore":{"label":"Top above the bore axis","kind":"length","required":true,"how":"Maker's figure (what fits under a handguard)."}},"part":{"anchors":{"journal":{"origin":[0,0,0],"note":"On the bore axis at the gas port, +x toward the muzzle."},"gas_tube":{"origin":[0,"{.height_above_bore}",0],"x":[-1,0,0]}},"interfaces":{"gas_journal":{"type":"ar15.gas_journal","role":"block","anchor":"journal","params":{"journal_od":"={.journal_id}"},"flips":false},"gas_tube":{"type":"ar15.gas_tube","role":"block","anchor":"gas_tube","params":{},"flips":false}},"materials":{"body":{"label":"Gas block","finish":"steel","recolorable":false,"color":"placeholder-black"}}},"calibration":[]},"gas_tube":{"category":"gas_tube","label":"Gas tube","about":"The thin tube that carries the gas back from the gas block to the bolt carrier. Its length goes with the barrel's gas system: carbine, mid-length or rifle.","mounts":false,"sight":false,"holds_sight":false,"inside":false,"ffl":false,"under":false,"dimensions":{"weight":{"label":"Weight","kind":"mass","required":false,"how":"Manufacturer spec table."},"length":{"label":"Length (carbine, mid, rifle)","kind":"length","required":true,"how":"The Army's drawing (gas tube assembly 8448567) or the maker's figure."},"od":{"label":"Outside diameter","kind":"length","required":true,"how":"The Army's drawing (8448567)."}},"part":{"anchors":{"block":{"origin":[0,0,0],"note":"At the block's tube hole, +x rearward (the block's anchor turns it)."}},"interfaces":{"gas_tube":{"type":"ar15.gas_tube","role":"tube","anchor":"block","params":{},"flips":false},"gas_system":{"type":"ar15.gas_system","role":"tube","params":{"length":"unstated"},"flips":false}},"materials":{"tube":{"label":"Gas tube","finish":"stainless","recolorable":false,"color":"stainless-natural"}}},"calibration":[]},"grip":{"category":"grip","label":"Grip","about":"Where the firing hand holds the rifle. Grips differ in their angle, their size and their surface.","mounts":false,"sight":false,"holds_sight":false,"inside":false,"ffl":false,"under":false,"dimensions":{"grip_angle":{"label":"Grip angle (the straps' lean from vertical, installed)","kind":"angle","required":true,"how":"Manufacturer page; checked by fitting the traced outline into a pin-framed photo of the grip installed (trace.py `register`, `registered_lean`)."},"bottom_below_lower_underside":{"label":"Grip bottom below the receiver's underside where the grip bears","kind":"length","required":true,"how":"A pin-framed photo of the grip installed (its toe below the pins, less the surface it bears on), or the maker's height. A maker's figure whose reference points aren't stated counts only when it checks: the patent's end view at that scale against the published thickness, and the outline's free fit into the installed photo (the MOE+'s 4.0 does; the K2+'s 4.1 doesn't)."},"thickness":{"label":"Thickness (side to side)","kind":"length","required":true,"how":"Manufacturer page; a design patent's end view checks it."},"seat_x":{"label":"Seat, X: where the grip's frame origin (its flat top's rear end) sits ahead of the takedown pin, installed","kind":"length","required":true,"how":"trace.py `register`: the traced outline fitted into a pin-framed photo of the grip installed on any lower with the standard grip mount (D19); `mode: rows` with `fix: { y: <lower>.grip_mating_y }` when only one strap shows."},"lug_slot_width":{"label":"The slot in the top that goes over the receiver's lug, across","kind":"length","required":false,"how":"A view of the grip's top from above: the slot's two walls against the top face's two edges in the same rows (one plane, so the ratio needs no scale), times that face's width. Its model is cut with it (pipeline/blender/lib.py `grip_receiver_cuts`: the standard lug's faces as clear of the slot behind and below as its width leaves them at the sides, and the standard receiver's round under a beavertail), and tried against a lower in a build (app/tests/grip-mount.test.ts): a grip drawn as a hull of its outlines stands in the lug until it is."},"weight":{"label":"Weight","kind":"mass","required":true,"how":"Manufacturer spec table."}},"part":{"anchors":{"grip_lug":{"origin":["-{.seat_x}",0,0],"note":"Grip frame: origin at the rear end of its flat top, which bears on the lower's underside. The anchor is the point of that top at the takedown pin's x once installed (seat_x)."}},"interfaces":{"grip_lug":{"type":"ar15.grip_lug","role":"grip","anchor":"grip_lug","params":{},"flips":false}},"materials":{"body":{"label":"Grip","finish":"polymer","recolorable":true,"color":"placeholder-polymer-black"}}},"calibration":[{"feature":"known-length","note":"A published height or drop on a straight side view"},{"feature":"patent","note":"A design patent's end view for the section (D26)"},{"feature":"frame","note":"Installed on a lower with its pins in view: the seat and the installed angle (`register`)"}]},"hand_stop":{"category":"hand_stop","label":"Hand stop","about":"A small stop on the handguard for the forward hand to pull against or to find its place by.","mounts":true,"sight":false,"holds_sight":false,"inside":false,"ffl":false,"under":true,"dimensions":{"length":{"label":"Overall length (along the handguard)","kind":"length","required":true,"how":"Manufacturer spec table; a straight side view scaled by a published size checks it."},"height":{"label":"Height (how far it stands off the handguard's face)","kind":"length","required":true,"how":"Manufacturer spec table; say what it is measured from. A side view of it installed, scaled by the M-LOK slots in frame (calibrate.py rail), checks it."},"width":{"label":"Width (side to side)","kind":"length","required":true,"how":"Manufacturer spec table; an end or underside view scaled by the length checks it."},"weight":{"label":"Weight","kind":"mass","required":true,"how":"Manufacturer spec table (say whether the kit's other pieces are in it)."},"lugs":{"label":"M-LOK slots its lugs span","kind":"count","required":true,"how":"The maker's page or instruction sheet: how many M-LOK slots it needs. The interface's `lugs` reads it: a part at slot n takes n and the next lugs − 1."},"reach_inside":{"label":"Reach inside the handguard (below the mounting face, tightened)","kind":"length","required":false,"how":"How far its T-nuts and lugs reach below its mounting face once tightened, from the maker's drawing or instruction sheet. The host states the room it has (`reach_inside` on its mlok interface) and the mlok type's rule compares them."},"lug_x":{"label":"Rear lug's centre ahead of the part's rear end","kind":"length","required":true,"how":"A straight side view scaled by the length and the height together (they must agree): where the rearmost T-nut's stem sits along the part, as a same-plane ratio against the part's ends. The `lug` anchor is there."}},"part":{"anchors":{"lug":{"origin":["{.lug_x} + {std.mlok.interval} / 2",0,0],"note":"The middle of its two lugs on the mounting face (its T-nuts stand the M-LOK interval apart, one in each half of a slot; a part with one nut: that nut, `{.lug_x}` alone; one whose nuts are another distance apart: half that distance): what an M-LOK position places. Hand stop frame: origin at the part's rear end on the mounting face (its top surface, which bears on the handguard), +x forward along the handguard, +y out of the face (away from the handguard, into the part's body: the solver turns it to the face it is on). `flipped` turns it end for end: which way its lip faces."}},"interfaces":{"mlok":{"type":"mlok","role":"accessory","anchor":"lug","params":{"lugs":"={.lugs}","reach_inside":"={.reach_inside}"},"flips":false,"note":"Set `flips: true` here if the maker says it mounts either way round (Magpul's M-LOK FAQ says so of M-LOK accessories in general; quote the part's own sheet where it says which way its lip goes). `lugs` and `reach_inside` are ledger expressions: the checklist's figures."}},"materials":{"body":{"label":"Hand stop","finish":"polymer","recolorable":true,"color":"placeholder-polymer-black"}}},"calibration":[{"feature":"known-length","note":"A published length or height on a straight side view"},{"feature":"mlok","note":"Installed on a handguard with its M-LOK slots in frame: the slots give the scale in the mounting plane (calibrate.py rail does M-LOK too), and which slot the rear lug is in"},{"feature":"drawing","note":"A manufacturer's dimensioned drawing or instruction sheet, for the lugs' positions and how far they reach inside"}]},"handguard":{"category":"handguard","label":"Handguard","about":"The tube round the barrel that the forward hand holds, and where lights, grips and sling mounts go. Its length is the main choice: how much of the barrel it covers, and how much room it leaves for a hand and for accessories.","mounts":false,"sight":false,"holds_sight":false,"inside":false,"ffl":false,"under":false,"room":["gas_block","muzzle_device","suppressor"],"reaches_over":["muzzle_device","suppressor"],"section":{"inside_diameter":"across","inside_height":"across"},"dimensions":{"weight":{"label":"Weight","kind":"mass","required":true,"how":"Manufacturer spec table."},"length":{"label":"Length","kind":"length","required":true,"how":"Maker's figure."},"width":{"label":"Width across the flats","kind":"length","required":true,"how":"Maker's figure or an end view."},"height":{"label":"Height","kind":"length","required":true,"how":"Maker's figure or an end view."},"inside_diameter":{"label":"Inside diameter","kind":"length","required":true,"how":"Maker's figure (what barrel and gas block fit under it)."},"rear_x":{"label":"Its rear face ahead of the receiver's front face","kind":"length","required":true,"how":"A photo of it mounted; the barrel nut's standoff."}},"part":{"anchors":{"mount":{"origin":[0,0,0],"note":"The receiver's front face on the bore axis, +x toward the muzzle."}},"interfaces":{"handguard_mount":{"type":"ar15.handguard_mount","role":"handguard","anchor":"mount","params":{"nut":"standard"},"flips":false}},"materials":{"body":{"label":"Handguard","finish":"anodized","recolorable":true,"color":"placeholder-black"}}},"calibration":[{"feature":"mlok","note":"Its M-LOK slots: the standard's pitch (std.mlok.slot_pitch) gives the scale along it (calibrate.py)."}]},"handguard_cap":{"category":"handguard_cap","label":"Handguard cap","about":"The steel cap behind the front sight base that the front of a drop-in handguard sits in. Round or triangular: the handguard says which it takes.","mounts":false,"sight":false,"holds_sight":false,"inside":false,"ffl":false,"under":false,"dimensions":{"weight":{"label":"Weight","kind":"mass","required":true,"how":"Maker's or seller's figure; else its steel, by its sizes and std.density.steel."},"journal_id":{"label":"Bore (the journal it fits: .750 or .625)","kind":"length","required":true,"how":"Maker's figure."},"length":{"label":"Depth along the bore","kind":"length","required":true,"how":"A side photo scaled by the bore."},"width":{"label":"Width across","kind":"length","required":true,"how":"An end-on photo scaled by the bore."},"height":{"label":"Height","kind":"length","required":true,"how":"An end-on photo scaled by the bore."}},"part":{"anchors":{"seat":{"origin":[0,0,0],"note":"Part frame: on the bore axis at its front face, which bears on the front sight base's rear face, +x toward the muzzle."}},"interfaces":{"handguard_cap":{"type":"ar15.handguard_cap","role":"cap","anchor":"seat","params":{},"flips":false},"drop_in":{"type":"ar15.drop_in","role":"cap","params":{},"flips":false}},"materials":{"cap":{"label":"Handguard cap","finish":"phosphate","recolorable":false,"color":"placeholder-black"}}},"calibration":[]},"light":{"category":"light","label":"Light","about":"A weapon light, clamped to a rail or bolted to the handguard.","mounts":true,"sight":false,"holds_sight":false,"inside":false,"ffl":false,"under":false,"behind":{"category":"muzzle_device","what":"the muzzle device","says":"Cloud Defensive, of any weapon light: \"We do not recommend mounting the head of your REIN or any brand of weapon light directly in line with your muzzle device. The ideal mounting location for your weapon light is behind the muzzle device.\"","source":"https://clouddefensive.com/pages/rein-faq"},"dimensions":{"weight":{"label":"Weight (say with which batteries, and whether the mount is in it)","kind":"mass","required":true,"how":"Manufacturer spec table."},"length":{"label":"Overall length","kind":"length","required":true,"how":"Manufacturer spec table or product sheet."},"head_diameter":{"label":"Head (bezel) diameter","kind":"length","required":true,"how":"Manufacturer spec table or product sheet; a straight side view scaled by the length checks it."},"body_diameter":{"label":"Body diameter","kind":"length","required":false,"how":"The product sheet, or a straight side view scaled by the length and the head's diameter together (tools/turned.py: ratios of radii are true whatever the camera's distance)."},"axis_above_mount":{"label":"The body's axis above the mounting face (the rail's top, the handguard's face)","kind":"length","required":false,"how":"The maker's drawing, or a straight side view of the light on its mount scaled by the head's diameter: the axis to the mount's bearing face. Say which mount."},"width":{"label":"Overall width (with its mount and switch)","kind":"length","required":false,"how":"Manufacturer spec table, or an end view scaled by the head's diameter."},"lugs":{"label":"M-LOK slots its mount's lugs span","kind":"count","required":false,"how":"For a light with an M-LOK mount: the maker's instruction sheet. The mlok interface's `lugs` reads it."},"reach_inside":{"label":"Reach inside the handguard (below the mounting face, tightened)","kind":"length","required":false,"how":"For a light with an M-LOK mount: how far its T-nuts reach below its mounting face, from the maker's sheet. The host states the room it has."}},"part":{"anchors":{"rail_clamp":{"origin":[0,0,0],"note":"Light frame: on the mounting face at the middle of its clamp, +x toward the lens, +y away from what it is mounted on."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{},"flips":false,"note":"For a light that clamps to a rail. Add params `clamp_rear` and `clamp_front` (how far its clamp reaches each way, as ledger expressions). A light that mounts only on M-LOK has an `mlok` interface instead (role accessory, an anchor at the middle of its two lugs on the mounting face, `lugs` and `reach_inside`); one that comes with both has both. `flips: true` where its maker says it mounts either way round."}},"materials":{"body":{"label":"Body","finish":"anodized","recolorable":false,"color":"placeholder-black"},"lens":{"label":"Lens","finish":"glass","recolorable":false,"color":"glass-clear"}}},"calibration":[{"feature":"known-length","note":"The published length and head diameter on a straight side view (they must agree)"},{"feature":"tube","note":"A turned body scaled by its own tube, column by column, where the photo is yawed (trace.py `calibrate: tube`)"},{"feature":"mlok","note":"Mounted on a handguard with its M-LOK slots in frame: which slots its mount takes, and the scale in the mounting plane"}]},"lower":{"category":"lower","label":"Lower receiver","about":"The part the rest of the rifle is built on: the trigger, the grip, the stock and the upper all go onto it. Sellers ship it only to a licensed dealer. A stripped one is the receiver alone; a complete one comes with the parts that go in it.","mounts":false,"sight":false,"holds_sight":false,"inside":false,"ffl":true,"under":false,"dimensions":{"weight":{"label":"Weight","kind":"mass","required":true,"how":"Manufacturer spec table (stripped, or complete as sold); a retailer's figure may be boxed."},"width":{"label":"Receiver maximum width (Z)","kind":"length","required":true,"how":"The TDP's body width for a mil-spec forging (std.ar15.lower_body_width); a maker's figure or an end view for anything else."},"buffer_axis_above_pin":{"label":"Receiver extension (bore) axis above the takedown pin centre","kind":"length","required":true,"how":"The Army's drawings for a mil-spec lower (std.ar15.bore_axis_y); check it on a pin-framed side photo, allowing for the pins' near ends being nearer the lens."},"magazine_seat_x":{"label":"Magazine seat, X (a seated magazine's frame origin ahead of the takedown pin)","kind":"length","required":true,"how":"A pin-framed photo of a magazine seated in it, fitted with its traced outline (trace.py `register`)."},"magazine_seat_y":{"label":"Magazine seat, Y (the feed-lip top of the magazine in that photo, seated)","kind":"length","required":false,"how":"The same photo: a check on the catch, which is what seats a magazine (the `magwell` anchor is at the catch's upper face, and each magazine hangs there by its own catch notch). The TDP's magwell (2.553 x 0.898 in inside) bounds any magazine drawn in it."},"grip_seat_y":{"label":"Grip seat, Y (the underside a grip's flat top bears on, at the takedown pin's X)","kind":"length","required":true,"how":"A pin-framed side photo: the receiver's underside behind the step. Each grip says where its own origin sits from here (D28)."},"trigger_guard_front_x":{"label":"Trigger guard front ear hole, X","kind":"length","required":true,"how":"The TDP for a mil-spec lower (std.ar15.*). A lower with an integral trigger guard states where its guard's ears would be, so the fcg and grip anchors still frame it; its guard is drawn with the receiver."},"trigger_guard_front_y":{"label":"Trigger guard front ear hole, Y","kind":"length","required":true,"how":"As above."},"trigger_guard_rear_x":{"label":"Trigger guard rear ear hole, X","kind":"length","required":true,"how":"As above."},"trigger_guard_rear_y":{"label":"Trigger guard rear ear hole, Y","kind":"length","required":true,"how":"As above."},"trigger_pin_x":{"label":"Trigger pin hole centre, X","kind":"length","required":true,"how":"The TDP (std.ar15.trigger_pin_x); every lower that takes a standard FCG has it there."},"trigger_pin_y":{"label":"Trigger pin hole centre, Y","kind":"length","required":true,"how":"The TDP; checked on a pin-framed photo."},"trigger_face_x":{"label":"The trigger's face ahead of the takedown pin (a complete lower: its trigger, at rest)","kind":"length","required":false,"how":"A pin-framed side photo of the complete lower: the front of the trigger's shoe where a finger lands. Length of pull is read from here."},"butt_behind_pin":{"label":"The stock's butt behind the takedown pin, at the position it is drawn at (a complete lower)","kind":"length","required":false,"how":"A pin-framed side photo of the complete lower with its stock collapsed (say which position); the stock maker's lengths of pull are a check only (M6)."}},"part":{"anchors":{"pins":{"origin":[0,0,0],"note":"The rifle frame origin."},"buffer_tube_mount":{"origin":[0,"{.buffer_axis_above_pin}",0],"x":[-1,0,0]},"magwell":{"origin":["{.magazine_seat_x}","{std.ar15.mag_catch_slot_bottom_y} + {std.ar15.mag_catch_slot_h}",0],"note":"Where a seated magazine hangs: x where its spine's rear face sits in the well, y at the catch's upper face (the standard's slot). A magazine's own anchor is the upper edge of its catch notch."},"grip_lug":{"origin":[0,"{.grip_seat_y}",0]},"trigger_guard":{"origin":["{.trigger_guard_front_x}","{.trigger_guard_front_y}",0],"x":["{.trigger_guard_front_x} - {.trigger_guard_rear_x}","{.trigger_guard_front_y} - {.trigger_guard_rear_y}",0]},"fcg":{"origin":["{.trigger_pin_x}","{.trigger_pin_y}",0]},"lpk":{"origin":[0,0,"-{std.ar15.lower_body_width} / 2"]},"selector":{"origin":["{std.ar15.selector_x}","{std.ar15.selector_y}",0],"note":"The selector's hole, on its axis at the receiver's mid-plane (D86)."}},"interfaces":{"receiver_pins":{"type":"ar15.upper_lower","role":"lower","anchor":"pins","params":{"pin_spacing":"={std.ar15.pin_spacing}"},"flips":false},"buffer_tube_mount":{"type":"ar15.buffer_tube_mount","role":"receiver","anchor":"buffer_tube_mount","params":{},"flips":false},"magwell":{"type":"ar15.magwell","role":"receiver","anchor":"magwell","params":{"family":"unstated"},"flips":false,"note":"Set the family from the product's page (5.56 for a standard AR-15 magwell)."},"grip_lug":{"type":"ar15.grip_lug","role":"receiver","anchor":"grip_lug","params":{},"flips":false},"trigger_guard":{"type":"ar15.trigger_guard","role":"receiver","anchor":"trigger_guard","params":{},"flips":false},"fcg":{"type":"ar15.fcg","role":"receiver","anchor":"fcg","params":{"pin_diameter":"unstated"},"flips":false,"note":"small-pin (.154) or large-pin (.170): from the product's page."},"lpk":{"type":"ar15.lpk","role":"receiver","anchor":"lpk","params":{},"flips":false},"selector":{"type":"ar15.selector","role":"receiver","anchor":"selector","params":{},"flips":false}},"materials":{"receiver":{"label":"Receiver","finish":"anodized","recolorable":true,"color":"placeholder-black","sheen":"matte"}}},"calibration":[{"feature":"frame","note":"The receiver pins, 6.375 in apart (std.ar15.pin_spacing), on any side photo: the frame every other feature is measured in. Their near ends set the scale; the body is 0.44 in further from the lens (M6)."},{"feature":"known-length","note":"A maker's stated length or height: a check on the pin frame, and a scale where the pins aren't both in view."}]},"lpk":{"category":"lpk","label":"Lower parts kit","about":"The small parts that go into a lower receiver: its pins, springs, catches and safety. Some kits bring a trigger, a grip and a trigger guard as well; with one that doesn't, those are chosen on their own.","mounts":false,"sight":false,"holds_sight":false,"inside":false,"ffl":false,"under":false,"dimensions":{"weight":{"label":"Weight","kind":"mass","required":true,"how":"Manufacturer spec table."},"takedown_pin_head_d":{"label":"The takedown pin head's diameter","kind":"length","required":true,"how":"The Army's drawings (8448621) for mil-spec pins."},"pivot_pin_head_d":{"label":"The pivot pin head's diameter","kind":"length","required":true,"how":"The Army's drawings (8448584)."},"pivot_pin_head_flat":{"label":"The pivot pin head's flat from the pin's axis","kind":"length","required":false,"how":"The Army's drawing (8448621: .1355). The head is drawn with it turned to the rear, beside the end of a forged lower's roll along the top of its well."},"selector_hub_d":{"label":"The selector's hub diameter","kind":"length","required":true,"how":"The Army's drawings (9381367)."},"selector_lever_t":{"label":"The selector lever's thickness","kind":"length","required":true},"bolt_catch_paddle_rear_x":{"label":"The bolt catch paddle's rear edge ahead of the takedown pin","kind":"length","required":true,"how":"A pin-framed photo of an assembled lower."},"magazine_release_w":{"label":"The magazine release button's width","kind":"length","required":true,"how":"The Army's drawings (8448636)."},"magazine_release_standoff":{"label":"How far the button stands out of the fence","kind":"length","required":true}},"part":{"anchors":{"lpk":{"origin":[0,0,0],"note":"On the receiver's left face, level with the takedown pin (the lower's own `lpk` anchor is there): the controls stand out from it toward -Z. A kit that brings a trigger, a grip or a guard draws them as component models, each built in this frame: on the receiver's middle, which is half the body's width (`std.ar15.lower_body_width`) toward +Z from here. A model is drawn where its file has it (blockout.ts `lpk`)."}},"interfaces":{"lpk":{"type":"ar15.lpk","role":"kit","anchor":"lpk","params":{},"flips":false}},"materials":{"controls":{"label":"Controls","finish":"steel","recolorable":false,"color":"placeholder-black"}}},"calibration":[{"feature":"frame","note":"The controls' places are the standard's (std.ar15.selector_x, mag_catch_x…); a pin-framed photo checks them."}]},"magazine":{"category":"magazine","label":"Magazine","about":"What holds the rounds and feeds them. It is chosen for the cartridge and for how many rounds it holds, which is also how far it hangs below the rifle.","mounts":false,"sight":false,"holds_sight":false,"inside":false,"ffl":false,"under":false,"dimensions":{"overall_height":{"label":"Overall height, feed lips to base","kind":"length","required":true,"by":"ar15.magwell","how":"Side view. Sibling calibration in a lineup photo, or a published length with a defined reference."},"body_height":{"label":"Body height below the feed-lip block","kind":"length","required":true,"by":"ar15.magwell","how":"Side view; overall_height minus the feed-lip block when the block is shared across a product line."},"feed_lip_block_height":{"label":"Feed-lip block height","kind":"length","required":true,"by":"ar15.magwell"},"front_to_back":{"label":"Front to back at the body top","kind":"length","required":true,"by":"ar15.magwell","how":"Side view; same calibration as the heights."},"catch_notch_top":{"label":"Magazine catch notch (left side), its upper edge below the feed lips' top","kind":"length","required":true,"by":"ar15.magwell","how":"A straight left-side view scaled by the overall height, measured down the body's own axis (magazines are photographed leaning); a design patent's left elevation is a second reading. This is what seats the magazine: its notch's upper edge hangs on the lower's catch (the `magwell` anchor)."},"hang_below_magwell":{"label":"Hang below the magwell when seated","kind":"length","required":true,"by":"ar15.magwell","how":"Derived: overall_height minus the insertion depth, which is fixed by the mag-catch interface. A check on the seat: a photo of it seated in a lower, where one is on file."},"weight":{"label":"Weight, empty","kind":"mass","required":true,"how":"Manufacturer spec table."},"stated_length":{"label":"Length as the manufacturer states it (reference points undefined)","kind":"length","required":false}},"part":{"cartridge":{"takes":["unstated"],"stated":"unstated","source":"unstated"},"anchors":{"magwell":{"origin":[0,"-{.catch_notch_top}",0],"note":"The upper edge of its catch notch, at its spine's rear face where it stands in the well: what hangs on the lower's catch, in the well's spine slot. Magazine frame: origin at the rear face of the body's straight top (its spine) at the top of the feed lips; a traced side profile uses the same origin. Where the outline's rearmost point is something else (a stop or a rib on the spine under the well, as the PMAG's), the anchor's x is how far ahead of it the spine is, from the ledger (the PMAG's spine_ahead_of_stop)."}},"interfaces":{"magwell":{"type":"ar15.magwell","role":"magazine","anchor":"magwell","params":{"family":"5.56"},"flips":false}},"materials":{"body":{"label":"Magazine body","finish":"polymer","recolorable":false,"color":"placeholder-polymer-black"}}},"calibration":[{"feature":"sibling","note":"Lineup photo containing a magazine whose overall height is already in the ledger"},{"feature":"known-length","note":"Published overall length with a defined reference"}]},"magnifier":{"category":"magnifier","label":"Magnifier","about":"A magnifier sits behind a red dot to enlarge its view, and on a flip mount swings aside when it isn't wanted.","mounts":true,"sight":true,"holds_sight":false,"inside":false,"ffl":false,"under":false,"dimensions":{"length":{"label":"Overall length","kind":"length","required":true,"how":"Manufacturer spec table or dimensioned drawing."},"width":{"label":"Overall width","kind":"length","required":true},"height":{"label":"Overall height","kind":"length","required":true},"weight":{"label":"Weight (with its mount)","kind":"mass","required":true,"how":"Manufacturer spec table."},"optical_axis_above_rail_spacer":{"label":"Optical axis above the rail's top, with its spacer","kind":"length","required":true,"how":"The maker's centreline height, matched to the red dot it sits behind."},"eye_relief":{"label":"Eye relief","kind":"length","required":true,"how":"The maker's figure: the `eye:` of the part."},"eyepiece_rear_behind_base":{"label":"The eyepiece's rear face behind the mount's centre","kind":"length","required":true,"how":"A dimensioned drawing or a side view scaled by two published sizes."}},"part":{"anchors":{"rail_clamp":{"origin":[0,0,0]},"optical_axis":{"origin":[0,"{.optical_axis_above_rail_spacer}",0]},"eyepiece":{"origin":["-{.eyepiece_rear_behind_base}","{.optical_axis_above_rail_spacer}",0]}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{},"flips":false},"sight_line":{"type":"optic.sight_line","role":"magnifier","params":{"magnification":"unstated"},"flips":false,"note":"What it is made to sit behind: 1 (a red dot), from the maker's page."}},"materials":{"body":{"label":"Body","finish":"anodized","recolorable":false,"color":"placeholder-black"},"lens":{"label":"Lenses","finish":"glass","recolorable":false,"color":"placeholder-black"}}},"calibration":[{"feature":"known-length","note":"Two published sizes on a straight side view; the maker's dimensioned drawing where there is one."}]},"muzzle_device":{"category":"muzzle_device","label":"Muzzle device","about":"What threads onto the end of the barrel: a flash hider, a brake, or a plain protector for the threads. It adds to the build's length.","mounts":false,"sight":false,"holds_sight":false,"inside":false,"ffl":false,"under":false,"section":{"od":"across"},"dimensions":{"length":{"label":"Length ahead of the barrel's shoulder, installed (to the front face; a washer's thickness included)","kind":"length","required":true,"how":"The published overall length when the device seats on the shoulder; add a crush washer's installed thickness when it takes one, and say so."},"od":{"label":"Largest outside diameter","kind":"length","required":true,"how":"Manufacturer spec table; a cylinder's silhouette in a side photo checks it."},"weight":{"label":"Weight","kind":"mass","required":true,"how":"Manufacturer spec table. A part that ships as part of another (a thread protector on an upper) sets `weightIncludedIn` instead."},"thread_length":{"label":"Barrel thread length it takes, or is made for","kind":"length","required":false,"how":"The barrel's threaded end, shoulder to muzzle face, that the device takes. From a drawing's threaded bore depth it is a limit: give it to the interface as `thread_length`, and a longer barrel thread is a misfit. From the maker's words alone (a manual's \"mounts on threads .400 in length\") it is what the device is made for: give it as `thread_length_made_for`, and a longer barrel thread is a check that can't be made. A protector that ships on its barrel states neither."}},"part":{"anchors":{"thread":{"origin":[0,0,0],"note":"Device frame: on the bore axis at the barrel's shoulder, +x toward the muzzle."},"front":{"origin":["{.length}",0,0],"note":"The device's front face: where the build's overall length ends."}},"interfaces":{"thread":{"type":"muzzle_thread","role":"device","anchor":"thread","params":{"thread":"unstated"},"flips":false,"note":"Set the thread from the product's page (1/2-28, 5/8-24), and `thread_length` or `thread_length_made_for` when a source gives the barrel thread it takes (see the checklist)."}},"materials":{"body":{"label":"Body","finish":"steel","recolorable":false,"color":"placeholder-black"}}},"calibration":[{"feature":"known-length","note":"Published length and diameter on a straight side view (they must agree)"},{"feature":"drawing","note":"An official or manufacturer drawing"}]},"optic":{"category":"optic","label":"Optic","about":"A sight that is looked through, such as a red dot: on a rifle's top rail, or screwed to a pistol's slide.","mounts":true,"sight":true,"holds_sight":false,"inside":false,"ffl":false,"under":false,"dimensions":{"length":{"label":"Overall length","kind":"length","required":true,"how":"Manufacturer spec table or dimensioned drawing."},"width":{"label":"Overall width","kind":"length","required":true,"how":"Manufacturer spec table; say what it includes (turrets, a clamp's nut)."},"height":{"label":"Overall height","kind":"length","required":true,"how":"Manufacturer spec table; say what it is measured from (the clamp's bottom or the rail's top)."},"optical_axis_above_rail":{"label":"Optical axis above the rail's top","kind":"length","required":false,"how":"The mount's stated centreline height, checked on a side view scaled by two published sizes. An optic on a footprint (D101) states axis_above_base instead: its mount sets the rest."},"axis_above_base":{"label":"Optical axis above its own base (the plane its footprint meets a mount's deck in)","kind":"length","required":false,"how":"Read where the dot meets the mount it is pictured on (a drawing's seam, a photo's notch), against the maker's axis height for the pair."},"weight":{"label":"Weight (with its mount)","kind":"mass","required":true,"how":"Manufacturer spec table."},"mount_length":{"label":"Mount's clamp length along the rail","kind":"length","required":false},"tube_od":{"label":"Main tube OD","kind":"length","required":false},"eye_relief":{"label":"Eye relief","kind":"length","required":false,"how":"The maker's figure, or both ends of its range (a variable scope's changes with magnification): the part's `eye:` names them and an `eyepiece` anchor at the eyepiece's rear face. A red dot's is unlimited: it states none."}},"part":{"anchors":{"rail_clamp":{"origin":[0,0,0],"note":"Optic frame: origin on the rail top surface at the middle of the mount's clamp, +x forward."},"optical_axis":{"origin":[0,"{.optical_axis_above_rail}",0]}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{},"flips":false,"note":"Add params `clamp_rear` and `clamp_front`: how far its clamp reaches behind and ahead of the anchor, as ledger expressions (a single clamp: half its length each way; a two-bolt mount: 0 and the bolt spacing). A mount clamped across the rail's seam is flagged by them."},"sight_line":{"type":"optic.sight_line","role":"sight","params":{"magnification":"unstated"},"flips":false,"note":"Set it from the product's page: 1x for a red dot or a holographic sight, the range for a scope (1-6x). The platform checks a magnifier against it."}},"materials":{"body":{"label":"Housing and mount","finish":"anodized","recolorable":false,"color":"placeholder-black"},"lens":{"label":"Lenses","finish":"glass","recolorable":false,"color":"glass-clear"}}},"calibration":[{"feature":"drawing","note":"A manufacturer's dimensioned drawing: a least-squares frame over its dimension lines (trace.py, line art)"},{"feature":"known-length","note":"Two published sizes on a straight side view (they must agree)"},{"feature":"picatinny","note":"On a rail, straight side on: the slots give the scale in the mount's plane (the body is nearer the lens)"}]},"optic_mount":{"category":"optic_mount","label":"Red dot mount","about":"What a red dot is screwed to, and what clamps it to the top rail. How tall it is sets how high the dot sits over the iron sights.","mounts":true,"sight":false,"holds_sight":true,"inside":false,"ffl":false,"under":false,"dimensions":{"deck_above_rail":{"label":"The deck's top (where the dot's base sits) above the rail's top","kind":"length","required":true,"how":"The maker's axis height for the dot it is sold with (\"1.41 in absolute co-witness\", \"39 mm\") less that dot's axis_above_base, read where the two meet in the drawing or the photo the pair is built from. A mount sold alone (D102): its maker's height less the axis over its base of the dot the page names (a T-2's where it names none, said as assumed), checked on the mount's own photos or drawing. The deck is the floor a dot's base stands on, between any lips or fences along its sides; those aren't drawn while the dots on file have bases as wide as their housings."},"deck_x":{"label":"The footprint's middle along the deck, ahead of the clamp's middle","kind":"length","required":true,"how":"A straight side view: the middle of the plate or block the dot's base stands on, unless a drawing gives the screws."},"mount_length":{"label":"Clamp length along the rail (at its foot)","kind":"length","required":true},"weight":{"label":"Weight","kind":"mass","required":true,"how":"The maker's figure for the mount alone; failing one, the mount's metal (its model's volume times its material's density), said as worked out."}},"part":{"anchors":{"rail_clamp":{"origin":[0,0,0],"note":"Mount frame: origin on the rail top surface under the middle of the clamp, +x forward."},"deck":{"origin":["{.deck_x}","{.deck_above_rail}",0],"note":"On the deck's top at the footprint's middle: where a dot's base is put."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{},"flips":false,"note":"Add params `clamp_rear` and `clamp_front`: how far its clamp reaches behind and ahead of the anchor, as ledger expressions (a single clamp: half its length each way). A mount clamped across the rail's seam is flagged by them."},"deck":{"type":"optic_footprint","role":"deck","anchor":"deck","params":{"pattern":"aimpoint_micro"},"flips":false,"note":"The footprint its deck is cut for, as the maker names it (data/interfaces.yaml, optic_footprint)."}},"materials":{"mount":{"label":"Mount","finish":"anodized_matte","recolorable":false,"color":"placeholder-black"}}},"calibration":[{"feature":"drawing","note":"The maker's dimensioned drawing of the dot on it: the seam between the dot's base and the deck read in it"},{"feature":"picatinny","note":"On a rail, straight side on: the slots give the scale in the mount's plane"}]},"pistol_barrel":{"category":"pistol_barrel","label":"Barrel","about":"The barrel sets what the pistol fires and how far it reaches; a threaded one takes a thread protector, a compensator or a silencer.","mounts":false,"sight":false,"holds_sight":false,"inside":false,"ffl":false,"under":false,"dimensions":{"stated_length":{"label":"Barrel length as its maker states it","kind":"length","required":true,"how":"The maker's spec table, verbatim: what federal law's line goes by."},"shoulder_x":{"label":"The thread's shoulder, ahead of the breech face","kind":"length","required":true,"by":"muzzle_thread"},"thread_length":{"label":"Threaded end, shoulder to muzzle face","kind":"length","required":false},"weight":{"label":"Weight","kind":"mass","required":true}},"part":{"anchors":{"slide":{"origin":[0,0,0],"note":"Barrel frame: origin at its breech face on the bore axis, +x toward the muzzle."},"muzzle":{"origin":["{.shoulder_x}",0,0],"note":"The thread's shoulder, where a muzzle device seats."}},"interfaces":{"slide":{"type":"tx22.barrel","role":"barrel","anchor":"slide","params":{},"flips":false},"muzzle":{"type":"muzzle_thread","role":"barrel","anchor":"muzzle","params":{"thread":"unstated"},"flips":false}},"materials":{"body":{"label":"Barrel","finish":"steel","recolorable":false,"color":"placeholder-black"}}},"calibration":[]},"pistol_frame":{"category":"pistol_frame","label":"Frame","about":"The part a pistol is built on: its grip, trigger and controls are on it, the slide rides on its rails and the magazine goes into its grip. It is the serialised part, which sellers ship only to a licensed dealer.","mounts":false,"sight":false,"holds_sight":false,"inside":false,"ffl":true,"under":false,"dimensions":{"bore_axis_y":{"label":"The bore axis's height above the frame's origin","kind":"length","required":true,"by":"tx22.slide","how":"Side view, scaled by the pistol's published sizes: the barrel's muzzle (its thread protector's) centre against the origin pin's. It is where the slide, the barrel and whatever is on the muzzle line up."},"slide_rear_x":{"label":"Where a closed slide's rear face stands, from the origin","kind":"length","required":true,"by":"tx22.slide","how":"Side view of the pistol closed: the slide's rear face against the origin pin. Each part's half of the seat: the frame states where, the slide has its origin there."},"rear_x":{"label":"The frame's rearmost point, from the origin","kind":"length","required":true,"how":"Side view: the tang behind the grip, the overall length's rear end."},"grip_bottom_y":{"label":"The grip's bottom face, where a magazine's base pad bears","kind":"length","required":true,"by":"tx22.magwell","how":"Side view: the grip's lower edge at the magazine's front, against the origin pin."},"magwell_x":{"label":"The front of a seated magazine's body at the grip's bottom","kind":"length","required":true,"by":"tx22.magwell"},"width":{"label":"Width across the frame's grip","kind":"length","required":true,"how":"A view from the front or the rear, or a camera fitted to an oblique; the published overall width is at the widest point (its controls)."},"weight":{"label":"Weight","kind":"mass","required":true,"how":"Where only the pistol's is published, the frame's is that less the others' (each a derived entry), said as worked out."}},"part":{"anchors":{"slide":{"origin":["{.slide_rear_x}","{.bore_axis_y}",0],"note":"Where a closed slide's rear face stands, on the bore axis: the slide's origin."},"magwell":{"origin":["{.magwell_x}","{.grip_bottom_y}",0],"note":"Where a seated magazine's base pad bears on the grip's bottom face, at the front of its body."},"rear":{"origin":["{.rear_x}",0,0],"note":"The frame's rearmost point: where the overall length begins."}},"interfaces":{"slide":{"type":"tx22.slide","role":"frame","anchor":"slide","params":{},"flips":false},"magwell":{"type":"tx22.magwell","role":"frame","anchor":"magwell","params":{},"flips":false}},"materials":{"body":{"label":"Frame","finish":"polymer","recolorable":false,"color":"placeholder-polymer-black"}}},"calibration":[{"feature":"known-length","note":"The pistol's published overall length and height on a straight side view (they must agree)"}]},"pistol_magazine":{"category":"pistol_magazine","label":"Magazine","about":"What holds the rounds in the pistol's grip and feeds them. It is chosen for how many it holds, which is also how far it stands below the grip.","mounts":false,"sight":false,"holds_sight":false,"inside":false,"ffl":false,"under":false,"dimensions":{"overall_height":{"label":"Overall height, feed lips to base","kind":"length","required":true},"below_grip":{"label":"How far its base pad stands below the grip, seated","kind":"length","required":true,"by":"tx22.magwell"},"weight":{"label":"Weight, empty","kind":"mass","required":true}},"part":{"cartridge":{"takes":["unstated"],"stated":"unstated","source":"unstated"},"anchors":{"magwell":{"origin":[0,0,0],"note":"Magazine frame: origin where its base pad's top meets the front of its body, on the mid-plane; +x toward the muzzle, +y up."}},"interfaces":{"magwell":{"type":"tx22.magwell","role":"magazine","anchor":"magwell","params":{},"flips":false}},"materials":{"body":{"label":"Magazine body","finish":"steel","recolorable":false,"color":"placeholder-black"}}},"calibration":[]},"rail_cover":{"category":"rail_cover","label":"Rail cover","about":"A panel that fills a stretch of the handguard's slots, for the hand.","mounts":true,"sight":false,"holds_sight":false,"inside":false,"ffl":false,"under":false,"dimensions":{"length":{"label":"Overall length (along the handguard)","kind":"length","required":true,"how":"Manufacturer spec table or information sheet; a plan or side view of it installed, scaled by the handguard's rail or slots in frame (calibrate.py rail), checks it. A cover made for one slot is about a slot pitch long."},"height":{"label":"Height (how far it stands off the handguard's face)","kind":"length","required":true,"how":"The maker's figure for how far it stands above the rail; say what it is measured from. A side view of it installed checks it."},"width":{"label":"Width (side to side)","kind":"length","required":true,"how":"Manufacturer spec table; a plan view scaled by the length checks it."},"weight":{"label":"Weight","kind":"mass","required":true,"how":"Manufacturer spec table, for one cover (a pack's weight over its count is a derived figure: say so)."},"lugs":{"label":"M-LOK slots it fills","kind":"count","required":true,"how":"The maker's page: how many M-LOK slots one cover fills. The interface's `lugs` reads it: a cover at slot n takes n and the next lugs - 1."},"reach_inside":{"label":"Reach inside the handguard (below the mounting face, locked)","kind":"length","required":false,"how":"How far its latches and whatever locks them reach below its mounting face once fitted, from the maker's drawing or a patent's elevation scaled by the cover's length. The host states the room it has (`reach_inside` on its mlok interface) and the mlok type's rule compares them."}},"part":{"anchors":{"lug":{"origin":["{.length} / 2",0,0],"note":"The middle of the cover on its mounting face: a cover drops into a slot and is centred on it (its latches are either side of its middle), so a slot's position is the cover's middle. Rail cover frame: origin at the part's rear end on the mounting face (the surface that bears on the handguard), +x forward along the handguard, +y out of the face (away from the handguard: the solver turns it to the face it is on)."}},"interfaces":{"mlok":{"type":"mlok","role":"accessory","anchor":"lug","params":{"lugs":"={.lugs}","reach_inside":"={.reach_inside}","in_slot":true},"flips":false,"note":"`in_slot`: a cover drops into a slot and fills it, so it is offered the slots themselves and never the positions between two (the M-LOK interval is for parts held by T-nuts: assembly/solve.ts). Set `flips: true` here if the maker says it mounts either way round and it isn't the same both ways. `lugs` and `reach_inside` are ledger expressions: the checklist's figures."}},"materials":{"body":{"label":"Rail cover","finish":"polymer","recolorable":true,"color":"placeholder-polymer-black"}}},"calibration":[{"feature":"known-length","note":"A published length or width on a straight plan or side view"},{"feature":"mlok","note":"Installed on a handguard with its rail or M-LOK slots in frame: they give the scale in the mounting plane"},{"feature":"drawing","note":"A design patent's elevations, each figure scaled by published sizes; the maker's information sheet"}]},"rail_section":{"category":"rail_section","label":"Rail section","about":"A short Picatinny rail that bolts onto the handguard's M-LOK slots, for a light, a grip or a laser made to clamp to a rail.","mounts":true,"sight":false,"holds_sight":false,"inside":false,"ffl":false,"under":true,"dimensions":{"length":{"label":"Overall length (along the handguard)","kind":"length","required":true,"how":"Manufacturer spec table; a straight side or top view scaled by its own rail slots at the standard's pitch checks it."},"height":{"label":"Height (its rail's top above the handguard's face it sits on)","kind":"length","required":true,"how":"Manufacturer spec table; say what it is measured from. A straight side view scaled by its rail slots, or installed with M-LOK slots in frame (calibrate.py rail), checks it."},"width":{"label":"Width (side to side, at its widest)","kind":"length","required":true,"how":"Manufacturer spec table; the rail's head is the standard's 0.835 in, so a width of more than that is its base."},"weight":{"label":"Weight","kind":"mass","required":true,"how":"Manufacturer spec table, for the section with the hardware it is sold with (say which)."},"rail_slots":{"label":"Rail slots","kind":"count","required":true,"how":"The maker's page (its name usually gives it), and counted on a top or side view."},"rail_slot0_x":{"label":"Rear rail slot's centre ahead of the part's rear end","kind":"length","required":true,"how":"A straight side or top view scaled by its own slots at the standard's pitch: where the rearmost slot's centre lies. The rest are on the standard's pitch from it."},"lugs":{"label":"M-LOK slots its T-nuts span","kind":"count","required":true,"how":"The maker's page or instruction sheet: how many M-LOK slots it needs (its T-nuts, one pair a slot or one T-nut a slot). The interface's `lugs` reads it: a part at slot n takes n and the next lugs − 1."},"lug_x":{"label":"Its seat on the M-LOK face: the centre of the M-LOK slot its rear T-nut is in, ahead of its rear end","kind":"length","required":true,"how":"Where its rear screw or T-nut is (an underside view, an installed view with the slots in frame, or the maker's drawing, scaled by its length), and the M-LOK slot that puts it in: a T-nut sits in a slot's rear half, half the M-LOK interval (`std.mlok.interval`) behind the slot's centre, as one of a hand stop's two lugs does. So a part at whole and half positions has every T-nut in a slot (2026-10-29: with the nut itself as the seat, the 7-slot polymer rail's front nut, 60 mm on, stood on a web). Magpul's photo of its aluminium 5-slot on a hand guard has the screws over the slots' centres, 10 mm ahead of this: a T-nut may sit anywhere along its slot, and the rear half is the place that makes every half position one."},"reach_inside":{"label":"Reach inside the handguard (below the mounting face, tightened)","kind":"length","required":false,"how":"How far its T-nuts and lugs reach below its mounting face once tightened, from the maker's drawing or instruction sheet; failing that, the M-LOK specification's T-nut, as the maker's sheet names it."}},"part":{"anchors":{"lug":{"origin":["{.lug_x}",0,0],"note":"The centre of the M-LOK slot its rear T-nut is in, on its mounting face (the nut in that slot's rear half): what an M-LOK position places. Rail section frame: origin at its rear end on the mounting face, +x toward the muzzle, +y away from the face."},"top_rail":{"origin":["{.rail_slot0_x}","{.height}",0],"note":"The rearmost rail slot's centre on the rail's top: what a clamp's position places, a slot further forward for each index."}},"interfaces":{"mlok":{"type":"mlok","role":"accessory","anchor":"lug","params":{"lugs":"={.lugs}","reach_inside":"={.reach_inside}"},"flips":false,"note":"Set `flips: true` where the maker says it goes on either way round."},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}"},"flips":false,"note":"What clamps to a Picatinny rail is mounted here (D72: a mount that carries others)."}},"materials":{"body":{"label":"Rail section","finish":"polymer","recolorable":true,"color":"placeholder-polymer-black"}}},"calibration":[{"feature":"known-length","note":"Its own rail slots at the standard's pitch, on a straight side or top view: a scale and a check along it"},{"feature":"mlok","note":"Installed on a handguard with its M-LOK slots in frame: the slots give the scale in the mounting plane (calibrate.py rail does M-LOK too), and which slot its rear T-nuts are in"},{"feature":"drawing","note":"The maker's instruction sheet, for its T-nuts' places and how far they reach inside"}]},"receiver_extension":{"category":"receiver_extension","label":"Receiver extension","about":"The tube at the back of the lower receiver that the stock rides on, also called the buffer tube: the buffer and its spring sit inside it and send the bolt forward again after each shot. Sold alone, or as a kit with its end plate, castle nut, buffer and spring.","mounts":false,"sight":false,"holds_sight":false,"inside":false,"ffl":false,"under":false,"dimensions":{"weight":{"label":"Weight","kind":"mass","required":true,"how":"Manufacturer spec table; a retailer's figure may be boxed."},"tube_od":{"label":"The tube's outside diameter","kind":"length","required":true,"how":"The standard's (std.receiver_extension.milspec_od or commercial_od) for a tube sold as mil-spec or commercial."},"tube_length":{"label":"The tube's length","kind":"length","required":true,"how":"Maker's figure or a dimensioned drawing."},"tube_front_behind_pin":{"label":"The tube's front face behind the takedown pin","kind":"length","required":true,"how":"The Army's drawings (std.receiver_extension.front_face_x) for a mil-spec thread."},"position_step":{"label":"The stock position step","kind":"length","required":true,"how":"The tube's drawing or the holes on a photo scaled by the tube's OD in its own plane."}},"part":{"anchors":{"receiver_thread":{"origin":[0,0,0],"x":[1,0,0],"note":"Part frame: on the tube axis at the takedown pin's X, +x rearward."},"tube":{"origin":[0,0,0],"x":[1,0,0]},"end":{"origin":["0in - {std.ar15.receiver_rear_x}",0,0],"x":[1,0,0],"note":"On the tube axis at the receiver's rear face (the Army's drawing), where an end plate bears."},"bore":{"origin":["0in - {std.ar15.upper_rear_face_x}",0,0],"x":[1,0,0],"note":"On the tube axis where a buffer's front face rests with the bolt forward: against the carrier's rear end, which stands at the upper receiver's rear face (the Army's drawings). The buffer and its spring are placed from it."}},"interfaces":{"receiver_thread":{"type":"ar15.buffer_tube_mount","role":"tube","anchor":"receiver_thread","params":{},"flips":false},"tube":{"type":"receiver_extension","role":"tube","anchor":"tube","params":{"profile":"unstated","od":"={.tube_od}","positions":6,"step":"={.position_step}"},"flips":false},"extension_end":{"type":"ar15.extension_end","role":"tube","anchor":"end","params":{},"flips":false},"bore":{"type":"ar15.extension_bore","role":"tube","anchor":"bore","params":{},"flips":false}},"materials":{"tube":{"label":"Receiver extension","finish":"anodized","recolorable":true,"color":"placeholder-black"}}},"calibration":[{"feature":"frame","note":"A pin-framed photo of the tube on a lower: the nut and the exposed tube."}]},"scope":{"category":"scope","label":"Scope","about":"A sight that magnifies. It is held in a scope mount, and the mount is what clamps to the rail.","mounts":true,"sight":true,"holds_sight":false,"inside":false,"ffl":false,"under":false,"dimensions":{"length":{"label":"Overall length (the objective's front face to the eyepiece's rear face)","kind":"length","required":true,"how":"Manufacturer spec table or dimensioned drawing."},"tube_od":{"label":"Main tube diameter","kind":"length","required":true,"how":"Manufacturer spec table (30 mm, 1 in, 34 mm): what the rings have to be bored for."},"weight":{"label":"Weight (the scope alone, without rings or a mount)","kind":"mass","required":true,"how":"Manufacturer spec table; say whether the figure is with a mount it is sold in."},"saddle_x":{"label":"Turret saddle's middle along the optical axis (where the turrets' axes cross it)","kind":"length","required":true,"how":"On a straight side view scaled by the tube's own diameter: the middle of the elevation turret."},"tube_rear_from":{"label":"Main tube behind the saddle, where it begins (ahead of the eyepiece's housing or the magnification ring)","kind":"length","required":true,"how":"On the side view: where the outline comes down to the tube's diameter. A ring can't be clamped behind it."},"tube_rear_to":{"label":"Main tube behind the saddle, where it ends at the saddle","kind":"length","required":true},"tube_front_from":{"label":"Main tube ahead of the saddle, where it begins at the saddle","kind":"length","required":true},"tube_front_to":{"label":"Main tube ahead of the saddle, where it ends (at the objective bell, or the front face of a straight tube)","kind":"length","required":true},"eye_relief":{"label":"Eye relief","kind":"length","required":false,"how":"The maker's figure, or both ends of its range (a variable scope's changes with magnification): the part's `eye:` names them and an `eyepiece` anchor at the eyepiece's rear face."},"width":{"label":"Overall width","kind":"length","required":false,"how":"Manufacturer spec table; say what it includes (turrets)."}},"part":{"anchors":{"optical_axis":{"origin":[0,0,0],"note":"Scope frame: origin on the optical axis, +x toward the objective. Say which station the origin is."},"tube":{"origin":["{.saddle_x}",0,0],"note":"On the optical axis at the middle of the turret saddle: what a mount's rings are placed by."}},"interfaces":{"tube":{"type":"scope_rings","role":"tube","anchor":"tube","params":{"diameter":"={.tube_od}","rear_from":"={.tube_rear_from} - {.saddle_x}","rear_to":"={.tube_rear_to} - {.saddle_x}","front_from":"={.tube_front_from} - {.saddle_x}","front_to":"={.tube_front_to} - {.saddle_x}"},"flips":false,"note":"The stretches of main tube a ring can be clamped on, each side of the saddle, from the scope's anchor (data/interfaces.yaml, scope_rings)."},"sight_line":{"type":"optic.sight_line","role":"sight","params":{"magnification":"unstated"},"flips":false,"note":"The range from the product's page (1-6x). The platform checks a magnifier against it."}},"materials":{"body":{"label":"Scope","finish":"anodized","recolorable":false,"color":"placeholder-black"},"lens":{"label":"Lenses","finish":"glass","recolorable":false,"color":"glass-clear"}}},"calibration":[{"feature":"tube","note":"A straight side view scaled by the main tube's own diameter column by column (trace.py `calibrate: tube`: product side views are yawed a few degrees), and by the published length between the end faces"},{"feature":"drawing","note":"A manufacturer's dimensioned drawing: a least-squares frame over its dimension lines (trace.py, line art)"}]},"scope_mount":{"category":"scope_mount","label":"Scope mount","about":"What holds a scope by its tube and clamps it to the rail.","mounts":true,"sight":false,"holds_sight":true,"inside":false,"ffl":false,"under":false,"dimensions":{"optical_axis_above_rail":{"label":"Ring axis above the rail's top","kind":"length","required":true,"how":"The maker's centreline height (1.535 in: \"centerline of optic to top of Pic rail\")."},"ring_bore":{"label":"Tube diameter the rings are bored for","kind":"length","required":true,"how":"The maker's figure (30 mm, 1 in, 34 mm)."},"ring_rear_x":{"label":"Rear ring, its middle ahead of the rear cross bolt","kind":"length","required":true,"how":"A straight side view of the mount, scaled by the rail's slots under its bolts or by a scope's tube in it."},"ring_front_x":{"label":"Front ring, its middle ahead of the rear cross bolt","kind":"length","required":true},"ring_length":{"label":"Each ring's length along the tube (face to face)","kind":"length","required":true},"mount_length":{"label":"Clamp length along the rail (at its foot)","kind":"length","required":false},"weight":{"label":"Weight","kind":"mass","required":true,"how":"Manufacturer spec table."}},"part":{"anchors":{"rail_clamp":{"origin":[0,0,0],"note":"Mount frame: origin on the rail top surface under the rear cross bolt, +x forward."},"rings":{"origin":["({.ring_rear_x} + {.ring_front_x}) / 2","{.optical_axis_above_rail}",0],"note":"On the rings' axis midway between the two rings: where a scope's saddle is put."}},"interfaces":{"rail_clamp":{"type":"picatinny","role":"mount","anchor":"rail_clamp","params":{},"flips":false,"note":"Add params `clamp_rear` and `clamp_front`: how far its clamp reaches behind and ahead of the anchor, as ledger expressions (a two-bolt mount: 0 and the bolt spacing). A mount clamped across the rail's seam is flagged by them. One held by clamp blocks and no cross bolt states the blocks' far ends. And `cross_rear` and `cross_front` (D90): how far behind and ahead of the anchor its rearmost and foremost cross bolts or recoil lugs lie, each of which needs a slot of the rail (a two-bolt mount: `cross_front` is the bolt spacing)."},"rings":{"type":"scope_rings","role":"rings","anchor":"rings","params":{"diameter":"={.ring_bore}","rear_ring":"=({.ring_rear_x} - {.ring_front_x}) / 2","front_ring":"=({.ring_front_x} - {.ring_rear_x}) / 2","ring_length":"={.ring_length}"},"flips":false,"note":"The two rings, each by its middle along the axis from the anchor between them, and how long each is: a scope's tube has to take both (data/interfaces.yaml, scope_rings)."}},"materials":{"body":{"label":"Mount","finish":"anodized","recolorable":false,"color":"placeholder-black"}}},"calibration":[{"feature":"picatinny","note":"On a rail, straight side on: the slots give the scale in the mount's plane"},{"feature":"known-length","note":"A scope's published tube diameter in its rings, or the cross bolts a whole number of slots apart (checked: CLAUDE.md, a scale set by a feature taken to be at a standard spacing)"}]},"selector":{"category":"selector","label":"Safety selector","about":"The lever above the grip that is turned between safe and fire. A parts kit comes with a plain one on the left side; others add a lever on the right, or turn through a shorter arc.","mounts":false,"sight":false,"holds_sight":false,"inside":false,"ffl":false,"under":false,"dimensions":{"weight":{"label":"Weight","kind":"mass","required":true,"how":"Maker's or a seller's figure for the selector as installed (not the boxed kit with its spare levers); failing that its own metal, worked out and said as that."},"shaft_d":{"label":"Diameter of the shaft that turns in the receiver","kind":"length","required":true,"how":"The maker's figure; failing that the standard selector's (std.ar15.selector_shaft_d, the Army's drawing 9381367), by reference and said to be that: whatever turns in the standard's hole (std.ar15.selector_hole_d) is turned to it."},"shaft_length":{"label":"Length of shaft between the faces that bear on the receiver's two sides","kind":"length","required":true,"how":"The drawing, or a view along the rifle (edge-on to the lever): from the lever's inner face to the far lever's inner face, or to the shaft's far end on a one-sided selector. It is what the receiver's width has to match."},"lever_reach":{"label":"The lever's reach from the selector's axis to its tip","kind":"length","required":true,"how":"A view straight along the selector's axis, scaled by the shaft's diameter or a published length; for a selector sold with levers of two lengths, the one it is drawn with (say which, and on which side)."},"lever_standoff":{"label":"How far the lever stands out from the receiver's side","kind":"length","required":true,"how":"An edge-on view, scaled by the same figure."},"throw":{"label":"The arc it turns through between safe and fire","kind":"angle","required":false,"how":"The maker's words (90, or 45 on a short-throw selector; one that can be assembled either way says both, in its notes)."}},"part":{"anchors":{"selector":{"origin":[0,0,0],"note":"Selector frame: on its axis, at the middle of the length of shaft that lies in the receiver (the receiver's mid-plane when it is in), with the selector on SAFE: +x toward the muzzle, +y up, +z out of the rifle's right side. A lever's inner face is half the shaft's length from here: on the receiver's side where the shaft is made to a forged receiver's width (the standard selector's), a little off it where the maker's shaft is longer (an ambidextrous one made for several receivers: read it on its photos, and say the gap)."}},"interfaces":{"selector":{"type":"ar15.selector","role":"selector","anchor":"selector","params":{},"flips":false}},"materials":{"body":{"label":"Selector","finish":"phosphate","recolorable":false,"color":"placeholder-black"}}},"calibration":[{"feature":"drawing","note":"The Army's drawing of the standard selector, for a mil-spec one"},{"feature":"known-length","note":"The shaft's diameter (the standard hole's) seen in the same view as the lever"}]},"slide":{"category":"slide","label":"Slide","about":"The top of a pistol, which runs back on the frame at each shot. It carries the sights, and on an optics-ready slide the cut a red dot screws into.","mounts":false,"sight":false,"holds_sight":false,"inside":false,"ffl":false,"under":false,"dimensions":{"length":{"label":"Length, rear face to front face","kind":"length","required":true,"by":"tx22.slide"},"height":{"label":"Height above the bore axis to the slide's top","kind":"length","required":true},"width":{"label":"Width","kind":"length","required":true},"breech_x":{"label":"Where the barrel's breech face stands, ahead of the slide's rear face","kind":"length","required":true,"by":"tx22.barrel","how":"Where the barrel's own reading and the slide's meet: the port's rear edge seen against the chamber, or the field-stripped view."},"weight":{"label":"Weight","kind":"mass","required":true}},"part":{"anchors":{"frame":{"origin":[0,0,0],"note":"Slide frame: origin at its rear face on the bore axis, +x toward the muzzle."},"barrel":{"origin":["{.breech_x}",0,0],"note":"Where the barrel's breech face stands: the barrel's origin."}},"interfaces":{"frame":{"type":"tx22.slide","role":"slide","anchor":"frame","params":{},"flips":false},"barrel":{"type":"tx22.barrel","role":"slide","anchor":"barrel","params":{},"flips":false}},"materials":{"body":{"label":"Slide","finish":"anodized","recolorable":false,"color":"placeholder-black"}}},"calibration":[{"feature":"known-length","note":"The pistol's published sizes on a straight side view"}]},"sling_mount":{"category":"sling_mount","label":"Sling mount","about":"A socket or a loop on the handguard that a sling attaches to.","mounts":true,"sight":false,"holds_sight":false,"inside":false,"ffl":false,"under":false,"dimensions":{"length":{"label":"Overall length (along the handguard)","kind":"length","required":true,"how":"Manufacturer spec table; a straight side or plan view scaled by a published size checks it."},"height":{"label":"Height (how far it stands off the handguard's face)","kind":"length","required":true,"how":"Manufacturer spec table; say what it is measured from."},"width":{"label":"Width (side to side)","kind":"length","required":true,"how":"Manufacturer spec table; a plan view scaled by the length checks it."},"weight":{"label":"Weight","kind":"mass","required":true,"how":"Manufacturer spec table (say whether the hardware is in it)."},"lugs":{"label":"M-LOK slots its lugs span","kind":"count","required":true,"how":"The maker's page or instruction sheet: how many M-LOK slots it needs. The interface's `lugs` reads it: a part at slot n takes n and the next lugs - 1."},"reach_inside":{"label":"Reach inside the handguard (below the mounting face, tightened)","kind":"length","required":false,"how":"How far its T-nuts and lugs reach below its mounting face once tightened, from the maker's drawing or instruction sheet. The host states the room it has (`reach_inside` on its mlok interface) and the mlok type's rule compares them."},"lug_x":{"label":"Rear lug's centre ahead of the part's rear end","kind":"length","required":true,"how":"A plan or side view scaled by the length: where the rearmost T-nut's screw sits along the part, as a same-plane ratio against the part's ends. The `lug` anchor is there."}},"part":{"anchors":{"lug":{"origin":["{.lug_x} + {std.mlok.interval} / 2",0,0],"note":"The middle of its two lugs on the mounting face (its T-nuts stand the M-LOK interval apart, one in each half of a slot; a part with one nut: that nut, `{.lug_x}` alone; one whose nuts are another distance apart: half that distance): what an M-LOK position places. Sling mount frame: origin at the part's rear end on the mounting face (the surface that bears on the handguard), +x forward along the handguard, +y out of the face (away from the handguard: the solver turns it to the face it is on)."}},"interfaces":{"mlok":{"type":"mlok","role":"accessory","anchor":"lug","params":{"lugs":"={.lugs}","reach_inside":"={.reach_inside}"},"flips":false,"note":"Set `flips: true` here if the maker says it mounts either way round. `lugs` and `reach_inside` are ledger expressions: the checklist's figures."}},"materials":{"body":{"label":"Sling mount","finish":"steel","recolorable":false,"color":"placeholder-black"}}},"calibration":[{"feature":"known-length","note":"A published length or width on a straight plan or side view"},{"feature":"mlok","note":"Installed on a handguard with its M-LOK slots in frame: the slots give the scale in the mounting plane, and which slot the rear lug is in"},{"feature":"drawing","note":"A design patent's elevations, each figure scaled by published sizes; the maker's instruction sheet for the lugs"}]},"stock":{"category":"stock","label":"Stock","about":"What goes against the shoulder. An adjustable one slides along the receiver extension to set how long the rifle is to the shoulder; stocks differ in weight, in where the cheek rests and in how they lock.","mounts":false,"sight":false,"holds_sight":false,"inside":false,"ffl":false,"under":false,"shortest":["charging_handle","end_plate"],"dimensions":{"length":{"label":"Overall length","kind":"length","required":true,"how":"Manufacturer page. With the height, it scales a straight side photo and checks that the photo is straight (the two scales must agree)."},"height":{"label":"Height","kind":"length","required":true,"how":"Manufacturer page."},"width":{"label":"Width","kind":"length","required":true,"how":"Manufacturer page: the widest point, and what an end section (a design patent's end view) is scaled by."},"weight":{"label":"Weight","kind":"mass","required":true,"how":"Manufacturer spec table."},"tube_axis_below_top":{"label":"Tube axis below the stock's top edge","kind":"length","required":true,"how":"The exposed tube in a photo of the stock on a rifle: its axis midway between its limbs, below the stock's top. Scale that photo by the stock's own length or a rail in it, not by the tube's width (a black tube reads 3% thin on white), and allow for the photo's tilt. A design patent's end view draws the bore as a hidden-line circle: fit a circle, as a check."},"butt_behind_pin_pos1":{"label":"Butt behind the takedown pin at position 1 (collapsed), on a carbine receiver extension","kind":"length","required":true,"how":"A pin-framed side photo of the stock on a rifle, at any position: fit the traced outline into it (trace.py `register`), count its steps back from where its front would meet the castle nut, and take them off. Then check it: the stock's front must not pass the castle nut, and the tube's front hole less where the stock's lock pin stands should agree. The maker's lengths of pull against another stock's are a check only: Magpul's have moved 0.4 in between revisions, and seated the MOE Carbine inside the nut (M6)."},"lop_collapsed":{"label":"Length of pull, collapsed (the maker's reference rifle)","kind":"length","required":false},"lop_extended":{"label":"Length of pull, extended (the maker's reference rifle)","kind":"length","required":false}},"part":{"anchors":{"butt":{"origin":[0,0,0],"note":"The butt's plane on the tube axis: the part frame's origin. Overall length and length of pull end here (a complete lower that comes with a stock states its own)."},"tube":{"origin":["{.butt_behind_pin_pos1}",0,0],"x":[-1,0,0],"note":"Stock frame: origin on the tube axis in the plane of the butt, +x forward. At position 1 this anchor sits at the takedown pin's X."}},"interfaces":{"tube":{"type":"receiver_extension","role":"stock","anchor":"tube","params":{"profile":"unstated"},"flips":false,"note":"Set the profile from the product's name or page (mil-spec or commercial). A body sold for both is one part with `fitments` (D28)."}},"materials":{"body":{"label":"Stock body","finish":"polymer","recolorable":true,"color":"placeholder-polymer-black"}}},"calibration":[{"feature":"known-length","note":"Published length and height on a straight side view: two scales that must agree (trace.py `dims`)"},{"feature":"patent","note":"A design patent's end and plan views, each scaled by the published sizes (D26)"},{"feature":"frame","note":"On a rifle with its pins in view: the seat (at any position: count the steps), and a check of the size. A Picatinny rail in the same photo checks the pins' scale"}]},"suppressor":{"category":"suppressor","label":"Suppressor","about":"A suppressor that locks onto a muzzle device made for it and comes off by hand. It is itself a regulated item under federal law, and adds to the rifle's length and weight.","mounts":false,"sight":false,"holds_sight":false,"inside":false,"ffl":true,"under":false,"section":{"od":"across"},"dimensions":{"length":{"label":"Overall length, rear face to front face","kind":"length","required":true,"how":"Manufacturer spec table."},"od":{"label":"Largest outside diameter","kind":"length","required":true,"how":"Manufacturer spec table; a cylinder's silhouette in a side photo checks it."},"weight":{"label":"Weight","kind":"mass","required":true,"how":"Manufacturer spec table (without the muzzle device, which is a part of its own)."},"added_length":{"label":"What it adds to the weapon's length on the muzzle device it is measured with","kind":"length","required":false,"how":"The maker's own figure, with which muzzle device it is given for. A check on the seat: the suppressor's front ahead of that device's front, as the two are drawn, has to come to it."}},"part":{"anchors":{"mount":{"origin":[0,0,0],"note":"Suppressor frame: on its axis at its rear face, +x toward the muzzle. Where it stands on a muzzle device is that device's half of the seat (its `suppressor_mount` anchor)."},"front":{"origin":["{.length}",0,0],"note":"The front face: where the build's overall length ends."}},"interfaces":{"mount":{"type":"suppressor_mount","role":"suppressor","anchor":"mount","params":{"system":"unstated"},"flips":false,"note":"Set `system` to the maker's name for what it locks onto, with the maker's sentence."}},"materials":{"body":{"label":"Body","finish":"steel","recolorable":false,"color":"placeholder-black"}}},"calibration":[{"feature":"known-length","note":"Published length and diameter on a straight side view (they must agree)"},{"feature":"drawing","note":"An official or manufacturer drawing"}]},"trigger":{"category":"trigger","label":"Trigger","about":"The trigger and the parts that work with it. What is chosen here is how the pull feels: how heavy it is, and whether it breaks in one stage or two.","mounts":false,"sight":false,"holds_sight":false,"inside":false,"ffl":false,"under":false,"dimensions":{"weight":{"label":"Weight","kind":"mass","required":true,"how":"Manufacturer spec table."},"pin_diameter":{"label":"Pin diameter (small .154 or large .170)","kind":"length","required":true,"how":"The product's page."},"face_offset_x":{"label":"The shoe's face ahead of the trigger pin, at rest","kind":"length","required":true,"how":"A side photo scaled by the pivot hole; length of pull reads from here."},"shoe_face_x":{"label":"The shoe's face ahead of the takedown pin on a mil-spec lower (derived)","kind":"length","required":true,"how":"Derived: std.ar15.trigger_pin_x + face_offset_x."},"shoe_width":{"label":"The shoe's width","kind":"length","required":false}},"part":{"anchors":{"fcg":{"origin":[0,0,0],"note":"The trigger pin axis."},"face":{"origin":["{.face_offset_x}",0,0]}},"interfaces":{"fcg":{"type":"ar15.fcg","role":"trigger","anchor":"fcg","params":{"pin_diameter":"unstated"},"flips":false}},"materials":{"body":{"label":"Trigger","finish":"steel","recolorable":false,"color":"placeholder-black"}}},"calibration":[{"feature":"hole","note":"The pivot hole's diameter (the pin's) scales a side photo."}]},"trigger_guard":{"category":"trigger_guard","label":"Trigger guard","about":"The loop under the trigger. Mostly a choice of shape and colour; some leave more room for a gloved finger.","mounts":false,"sight":false,"holds_sight":false,"inside":false,"ffl":false,"under":false,"dimensions":{"weight":{"label":"Weight","kind":"mass","required":true,"how":"Manufacturer spec table."},"ear_spacing":{"label":"The ears' hole spacing","kind":"length","required":true,"how":"The standard's (std.ar15.trigger_guard_hole_spacing): it pins into a mil-spec lower."},"length_side":{"label":"Length in the side view","kind":"length","required":true,"how":"A side photo scaled by the ear spacing."},"height_side":{"label":"Height in the side view","kind":"length","required":true},"width_listed":{"label":"Width","kind":"length","required":false,"how":"Maker's figure or a plan view."}},"part":{"anchors":{"trigger_guard":{"origin":[0,0,0],"note":"At the front ear hole, x through the rear one."}},"interfaces":{"trigger_guard":{"type":"ar15.trigger_guard","role":"guard","anchor":"trigger_guard","params":{},"flips":false}},"materials":{"body":{"label":"Guard","finish":"polymer","recolorable":true,"color":"placeholder-polymer-black"}}},"calibration":[{"feature":"known-length","note":"The standard's ear spacing on the part's own holes."}]},"upper":{"category":"upper","label":"Upper","about":"The top half: it holds the barrel and the bolt carrier, and its rail is where sights go. A complete upper comes with its barrel, handguard and gas parts; a stripped one is the receiver alone, and those are chosen one by one.","mounts":false,"sight":false,"holds_sight":false,"inside":false,"ffl":false,"under":false,"dimensions":{"weight":{"label":"Weight (as sold: a complete upper counts its barrel, handguard, bolt carrier and charging handle)","kind":"mass","required":true,"how":"Manufacturer spec table; say what it includes."},"bore_axis_above_pin":{"label":"Bore axis above the takedown pin centre","kind":"length","required":true,"how":"The Army's drawings (std.ar15.bore_axis_y) for a mil-spec upper; a photo on its lower checks it."},"rail_top_above_pin":{"label":"The top rail's surface above the pin line","kind":"length","required":true,"how":"A pin-framed side photo (the standard's rail height above the deck: 2.07 on a mil-spec upper)."},"rail_slot0_x":{"label":"The rearmost rail slot's centre ahead of the takedown pin","kind":"length","required":true,"how":"A rail-framed photo (calibrate.py rail): the slots' phase and ends."},"rail_slots":{"label":"How many rail slots","kind":"count","required":true,"how":"The rail-framed photo."},"receiver_rear_x":{"label":"The receiver's rear face behind the takedown pin (negative)","kind":"length","required":true,"how":"The Army's drawings (std.ar15.receiver_rear_x) for a mil-spec upper."},"muzzle_shoulder_x":{"label":"The barrel's shoulder ahead of the takedown pin: where a muzzle device seats","kind":"length","required":true,"when":"barrel","how":"A rail-framed side photo; the thread protector's length and the published barrel length check it."},"barrel_od":{"label":"The barrel's diameter ahead of the handguard","kind":"length","required":true,"when":"barrel","how":"A side photo scaled in the barrel's plane (not a glossy tube's width: the rail's slots)."},"handguard_front_x":{"label":"The handguard's front face ahead of the takedown pin","kind":"length","required":true,"when":"handguard","how":"A rail-framed side photo."},"handguard_rear_x":{"label":"The handguard's rear face (the receiver/handguard seam) ahead of the takedown pin","kind":"length","required":true,"when":"handguard","how":"A rail-framed side photo; a complete upper's rail states its seam from this."},"handguard_height":{"label":"The handguard's height","kind":"length","required":true,"when":"handguard","how":"A side photo, with heights checked against the rail top and the receiver's deck."},"handguard_width":{"label":"The handguard's width across the flats","kind":"length","required":true,"when":"handguard","how":"Maker's figure or an end view."},"front_face_x":{"label":"A stripped receiver's front face (the end of its barrel-nut thread) ahead of the takedown pin","kind":"length","required":false,"how":"The Army's drawings (std.ar15.upper_front_face_x) for a mil-spec upper; its lug holes in a side photo check it."},"underside_y":{"label":"A stripped receiver's underside above the pin line (it sits on the lower's deck)","kind":"length","required":false,"how":"The Army's drawings (std.ar15.deck_y) for a mil-spec upper; a pin-framed side photo checks it."},"handle_seat_x":{"label":"A stripped receiver's open notch under its rail's rear end, its front wall ahead of the takedown pin: where a charging handle's shoulder stops","kind":"length","required":false,"how":"Its own side outline's wall (the notch is see-through from the side); the Army's drawing, scaled, is beside it for a mil-spec upper (std.ar15.charging_handle_seat_x, 0.075 ± 0.015). The receiver's charging-handle anchor is here, not at its rear face."},"muzzle_thread_length":{"label":"The muzzle thread's length (shoulder to face)","kind":"length","required":false,"how":"Maker's figure, or the thread protector's length and a photo of the bare muzzle."},"width":{"label":"The receiver's width","kind":"length","required":false}},"part":{"anchors":{"pins":{"origin":[0,0,0]},"top_rail":{"origin":["{.rail_slot0_x}","{.rail_top_above_pin}",0]},"muzzle":{"origin":["{.muzzle_shoulder_x}","{.bore_axis_above_pin}",0]}},"interfaces":{"receiver_pins":{"type":"ar15.upper_lower","role":"upper","anchor":"pins","params":{"pin_spacing":"={std.ar15.pin_spacing}"},"flips":false},"top_rail":{"type":"picatinny","role":"rail","anchor":"top_rail","params":{"pitch":"={std.picatinny.slot_pitch}","slots":"={.rail_slots}"},"flips":false,"note":"A rail over two parts states `seam` (D29)."},"muzzle":{"type":"muzzle_thread","role":"barrel","anchor":"muzzle","params":{"thread":"unstated"},"flips":false,"note":"The thread from the product's page (1/2-28); `thread_length` when known."}},"materials":{"receiver":{"label":"Receiver","finish":"anodized","recolorable":true,"color":"placeholder-black"},"barrel":{"label":"Barrel","finish":"steel","recolorable":false,"color":"placeholder-black"}}},"calibration":[{"feature":"picatinny","note":"The top rail's slots: the scale in the rail's plane (calibrate.py rail), with the tilt removed."},{"feature":"frame","note":"On a lower with its pins in view: the seat on the deck and the rail height."}]},"vertical_grip":{"category":"vertical_grip","label":"Vertical grip","about":"A grip that stands down from the handguard for the forward hand.","mounts":true,"sight":false,"holds_sight":false,"inside":false,"ffl":false,"under":true,"dimensions":{"length":{"label":"Overall length (along the handguard)","kind":"length","required":true,"how":"Manufacturer spec table; a straight side view scaled by a published size checks it."},"height":{"label":"Height (how far it stands off the handguard's face)","kind":"length","required":true,"how":"Manufacturer spec table; say what it is measured from (the mounting face, or the handguard's surface). A side view of it installed, scaled by the M-LOK slots in frame (calibrate.py rail), checks it."},"width":{"label":"Width (side to side)","kind":"length","required":true,"how":"Manufacturer spec table; an end or underside view scaled by the length checks it."},"weight":{"label":"Weight","kind":"mass","required":true,"how":"Manufacturer spec table."},"lugs":{"label":"M-LOK slots its lugs span","kind":"count","required":true,"how":"The maker's page or instruction sheet: how many M-LOK slots it needs (one T-nut per slot). The interface's `lugs` reads it: a part at slot n takes n and the next lugs − 1."},"reach_inside":{"label":"Reach inside the handguard (below the mounting face, tightened)","kind":"length","required":false,"how":"How far its T-nuts and lugs reach below its mounting face once tightened, from the maker's drawing or instruction sheet; failing that, the M-LOK specification's T-nut, as the maker's sheet names it. The host states the room it has (`reach_inside` on its mlok interface) and the mlok type's rule compares them."},"lug_x":{"label":"Rear lug's centre ahead of the part's rear end","kind":"length","required":true,"how":"A straight side view scaled by the length and the height together (they must agree): where the rearmost T-nut's stem sits along the plate, as a same-plane ratio against the plate's ends. The `lug` anchor is there."}},"part":{"anchors":{"lug":{"origin":["{.lug_x} + {std.mlok.interval} / 2",0,0],"note":"The middle of its two lugs on the mounting face (its T-nuts stand the M-LOK interval apart, one in each half of a slot; a part with one nut: that nut, `{.lug_x}` alone; one whose nuts are another distance apart: half that distance): what an M-LOK position places. Vertical grip frame: origin at the plate's rear end on the mounting face (its top surface, which bears on the handguard), +x forward along the handguard, +y out of the face (away from the handguard, into the grip's body: the solver turns it to the face it is on)."}},"interfaces":{"mlok":{"type":"mlok","role":"accessory","anchor":"lug","params":{"lugs":"={.lugs}","reach_inside":"={.reach_inside}"},"flips":false,"note":"Set `flips: true` here if the maker says it mounts either way round (a hand stop with a lip toward the muzzle or the shooter). `lugs` and `reach_inside` are ledger expressions: the checklist's figures."}},"materials":{"body":{"label":"Grip","finish":"polymer","recolorable":true,"color":"placeholder-polymer-black"}}},"calibration":[{"feature":"known-length","note":"A published length or height on a straight side view"},{"feature":"mlok","note":"Installed on a handguard with its M-LOK slots in frame: the slots give the scale in the mounting plane (calibrate.py rail does M-LOK too), and which slot the rear lug is in"},{"feature":"drawing","note":"A manufacturer's dimensioned drawing or instruction sheet, for the lugs' positions and how far they reach inside"}]}},"models":{"a2-flash-hider":{"part":"a2-flash-hider","model":"a2-flash-hider.glb","script":"a2_flash_hider.py","inputs":{"a2-flash-hider.cage_length":0.8,"a2-flash-hider.cage_od":0.834,"a2-flash-hider.chamber_cone_angle":90,"a2-flash-hider.chamber_d":0.67,"a2-flash-hider.chamber_from_front":0.88,"a2-flash-hider.compensator_length":1.75,"a2-flash-hider.exit_bore_d":0.343,"a2-flash-hider.flats_across":0.74,"a2-flash-hider.front_chamfer":0.04,"a2-flash-hider.groove_1_x":0.22,"a2-flash-hider.groove_2_x":0.48,"a2-flash-hider.groove_d":0.62,"a2-flash-hider.groove_width":0.12,"a2-flash-hider.od":0.862,"a2-flash-hider.rear_chamfer":0.03,"a2-flash-hider.rear_length":0.72,"a2-flash-hider.slot_center_from_front":0.59,"a2-flash-hider.slot_cutter_offset":0.61,"a2-flash-hider.slot_cutter_r":0.5,"a2-flash-hider.slot_flank_angle":30,"a2-flash-hider.slot_spacing":45,"a2-flash-hider.slot_tip_width":0.09,"a2-flash-hider.slot_width":0.185,"a2-flash-hider.slots":5,"a2-flash-hider.spacer_id":0.515,"a2-flash-hider.spacer_od":0.74,"a2-flash-hider.spacer_thickness":0.0525,"a2-flash-hider.step_angle":45,"a2-flash-hider.thread_depth":0.69},"profiles":{},"bounds":{"min":[0,-0.431,-0.431],"max":[1.8025,0.431,0.431]},"volume_in3":0.5235,"centroid":[0.6722,-0.0214,0],"shell":[0.8555,-0.0107,0],"area_in2":8.5679,"triangles":26374,"manifold":true,"slabs":[[0,-0.431,-0.37,0.361,0.431,0.37],[0.361,-0.431,-0.431,1.803,0.431,0.431]],"slots":["body","spacer"]},"aero-556-16-mid-barrel":{"part":"aero-556-16-mid-barrel","model":"aero-556-16-mid-barrel.glb","script":"aero_556_16_mid_barrel.py","inputs":{"aero-556-16-mid-barrel.bore_d":0.2195,"aero-556-16-mid-barrel.extension_rear_x":-0.979,"aero-556-16-mid-barrel.overall_length":16.501,"aero-556-16-mid-barrel.shoulder_x":14.89,"aero-556-16-mid-barrel.thread_length":0.63,"aero-556-16-mid-barrel.thread_major_d":0.4957,"aero-556-16-mid-barrel.thread_minor_d":0.4551,"aero-556-16-mid-barrel.thread_pitch":0.03571},"profiles":{"side":[[0.058,0.473],[0.058,-0.473],[0.081,-0.496],[1.002,-0.496],[1.056,-0.587],[1.164,-0.587],[1.218,-0.478],[1.904,-0.478],[2.012,-0.442],[2.211,-0.424],[2.301,-0.388],[2.409,-0.388],[2.427,-0.37],[2.608,-0.352],[2.626,-0.334],[9.014,-0.298],[9.231,-0.37],[9.303,-0.424],[9.916,-0.424],[9.952,-0.37],[9.97,-0.388],[10.241,-0.388],[10.259,-0.37],[15.06,-0.37],[15.078,-0.388],[15.186,-0.388],[15.222,-0.352],[15.944,-0.352],[15.971,-0.289],[15.953,-0.271],[15.98,-0.226],[16.106,-0.262],[16.124,-0.244],[16.142,-0.262],[16.16,-0.244],[16.485,-0.244],[16.503,-0.262],[16.539,-0.244],[16.581,-0.202],[16.581,0.184],[16.521,0.244],[16.503,0.226],[16.034,0.226],[15.98,0.208],[15.971,0.289],[15.944,0.334],[15.222,0.334],[15.204,0.352],[11.847,0.352],[11.829,0.37],[9.952,0.37],[9.934,0.352],[9.898,0.424],[9.862,0.406],[9.285,0.406],[9.158,0.334],[9.032,0.298],[2.662,0.334],[2.644,0.352],[2.463,0.37],[2.445,0.388],[2.319,0.388],[2.211,0.424],[1.994,0.442],[1.796,0.496],[1.687,0.478],[1.669,0.496],[1.218,0.496],[1.209,0.541],[1.164,0.587],[1.056,0.587],[1.029,0.559],[1.02,0.496],[0.532,0.496],[0.081,0.496]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"x":"extension_rear_x"}}},"bounds":{"min":[-0.98,-0.587,-0.587],"max":[15.52,0.587,0.587]},"volume_in3":6.19,"centroid":[6.2472,0,0],"shell":[6.9304,0,0],"area_in2":50.3744,"triangles":10466,"manifold":true,"slabs":[[-0.98,-0.496,-0.496,-0.155,0.496,0.496],[-0.155,-0.587,-0.587,0.258,0.587,0.587],[0.258,-0.533,-0.533,1.083,0.533,0.533],[1.083,-0.432,-0.432,1.495,0.432,0.432],[1.495,-0.362,-0.362,5.62,0.362,0.362],[5.62,-0.332,-0.332,8.095,0.332,0.333],[8.095,-0.424,-0.424,8.92,0.424,0.424],[8.92,-0.37,-0.37,15.108,0.37,0.37],[15.108,-0.248,-0.248,15.52,0.248,0.248]],"slots":["barrel"]},"aero-556-bcg":{"part":"aero-556-bcg","model":"aero-556-bcg.glb","script":"mil_spec_bolt_carrier_groups.py","inputs":{"aero-556-bcg.length":6.672,"aero-556-bcg.od":0.994,"std.ar15.carrier_body_od":0.93,"std.ar15.carrier_bolt_body_d":0.528,"std.ar15.carrier_bolt_cam_hole_to_face":1.305,"std.ar15.carrier_bolt_face_from_rear":2.675,"std.ar15.carrier_bolt_face_recess_d":0.38,"std.ar15.carrier_bolt_head_d":0.55,"std.ar15.carrier_bolt_length":2.8,"std.ar15.carrier_bolt_lug_length":0.278,"std.ar15.carrier_bolt_lug_od":0.743,"std.ar15.carrier_bolt_lug_offset":67.5,"std.ar15.carrier_bolt_lug_pitch":45,"std.ar15.carrier_bolt_lug_root_d":0.53,"std.ar15.carrier_bolt_lug_slot_width":0.102,"std.ar15.carrier_bolt_lugs":7,"std.ar15.carrier_bottom_cut_depth":0.215,"std.ar15.carrier_bottom_cut_rear":5.0965,"std.ar15.carrier_bottom_cut_rear_r":0.125,"std.ar15.carrier_cam_advance":0.255,"std.ar15.carrier_cam_advance_20":0.195,"std.ar15.carrier_cam_angle":22.5,"std.ar15.carrier_cam_dwell":0.042,"std.ar15.carrier_cam_pin_d":0.3105,"std.ar15.carrier_cam_pin_head_corner_d":0.47,"std.ar15.carrier_cam_pin_head_height":0.095,"std.ar15.carrier_cam_pin_head_length":0.32,"std.ar15.carrier_cam_pin_head_width":0.401,"std.ar15.carrier_cam_pin_hole_to_head":0.507,"std.ar15.carrier_cam_tail":0.07,"std.ar15.carrier_cam_width":0.3165,"std.ar15.carrier_cam_x":0.64,"std.ar15.carrier_cut_corner_r":0.12,"std.ar15.carrier_front_chamfer":0.075,"std.ar15.carrier_front_chamfer_angle":45,"std.ar15.carrier_front_flat_drop":0.095,"std.ar15.carrier_groove_angle":45,"std.ar15.carrier_groove_r":0.078,"std.ar15.carrier_groove_runout_from_shoulder":2.35,"std.ar15.carrier_groove_runout_r":1.5,"std.ar15.carrier_key_base_height":0.241,"std.ar15.carrier_key_bore_d":0.1805,"std.ar15.carrier_key_bore_depth":0.82,"std.ar15.carrier_key_cbore_d":0.273,"std.ar15.carrier_key_foot_length":1.31,"std.ar15.carrier_key_length":2.465,"std.ar15.carrier_key_mouth_angle":60,"std.ar15.carrier_key_mouth_d":0.225,"std.ar15.carrier_key_ramp_angle":45,"std.ar15.carrier_key_ramp_top":1.26,"std.ar15.carrier_key_screw_from_front":1.765,"std.ar15.carrier_key_screw_head_d":0.266,"std.ar15.carrier_key_screw_head_h":0.159,"std.ar15.carrier_key_screw_socket":0.125,"std.ar15.carrier_key_screw_socket_depth":0.077,"std.ar15.carrier_key_screw_spacing":0.5,"std.ar15.carrier_key_screw_x":2.055,"std.ar15.carrier_key_seat_front":1.37,"std.ar15.carrier_key_seat_rear":2.74,"std.ar15.carrier_key_seat_runout_r":0.5,"std.ar15.carrier_key_seat_y":0.42,"std.ar15.carrier_key_slot_width":0.4035,"std.ar15.carrier_key_step":0.03,"std.ar15.carrier_key_step_height":0.182,"std.ar15.carrier_key_tube_axis_y":0.361,"std.ar15.carrier_key_tube_d":0.25,"std.ar15.carrier_key_tube_length":0.9,"std.ar15.carrier_key_width":0.4005,"std.ar15.carrier_length":6.672,"std.ar15.carrier_pad_edge_angle":55,"std.ar15.carrier_pad_front":0.38,"std.ar15.carrier_rail_od":0.994,"std.ar15.carrier_rail_top_drop":0.67,"std.ar15.carrier_rear_chamfer":0.03,"std.ar15.carrier_rear_chamfer_angle":30,"std.ar15.carrier_relief_angle":75,"std.ar15.carrier_retaining_pin_csk_angle":82,"std.ar15.carrier_retaining_pin_csk_d":0.281,"std.ar15.carrier_retaining_pin_hole_d":0.093,"std.ar15.carrier_retaining_pin_x":2.536,"std.ar15.carrier_retaining_pin_y":0.157,"std.ar15.carrier_rib_bottom_drop":0.859,"std.ar15.carrier_rib_chamfer_across":0.87,"std.ar15.carrier_rib_chamfer_angle":22.5,"std.ar15.carrier_rib_rear":2.81,"std.ar15.carrier_rib_taper_angle":4.5,"std.ar15.carrier_rib_taper_start":1.8,"std.ar15.carrier_rib_width":0.399,"std.ar15.carrier_scallop_across":0.8125,"std.ar15.carrier_scallop_angle":22.5,"std.ar15.carrier_scallop_flat":0.375,"std.ar15.carrier_scallop_r":0.47,"std.ar15.carrier_scallop_rear":1.5,"std.ar15.carrier_serration_count":28,"std.ar15.carrier_serration_cutter_r":0.3125,"std.ar15.carrier_serration_depth":0.042,"std.ar15.carrier_serration_face_angle":70.5,"std.ar15.carrier_serration_flank_angle":22.25,"std.ar15.carrier_serration_front":1.9,"std.ar15.carrier_serration_pitch":0.125,"std.ar15.carrier_side_hole_d":0.125,"std.ar15.carrier_side_hole_x":2.15,"std.ar15.carrier_slab_height":0.5,"std.ar15.carrier_slot_travel":1.75,"std.ar15.carrier_slot_width":0.5,"std.ar15.carrier_tail_bore":0.625,"std.ar15.carrier_tail_front":5.1,"std.ar15.carrier_tail_notch_depth":0.1,"std.ar15.carrier_tail_notch_width":0.156,"std.ar15.carrier_top_cut_length":2.07,"std.ar15.carrier_vent_angle":45,"std.ar15.carrier_vent_d":0.109,"std.ar15.carrier_vent_x":1.34},"profiles":{},"bounds":{"min":[0,-0.4583,-0.4659],"max":[7.462,0.906,0.4659]},"volume_in3":2.9018,"centroid":[4.1793,0.0669,-0.0073],"shell":[3.7848,0.0999,0.0007],"area_in2":33.6114,"triangles":20152,"manifold":true,"slabs":[[0,-0.458,-0.465,1.964,0.465,0.465],[1.964,-0.25,-0.465,3.535,0.252,0.465],[3.535,-0.349,-0.466,4.713,0.661,0.466],[4.713,-0.362,-0.466,6.677,0.906,0.466],[6.677,-0.275,-0.275,7.069,0.275,0.275],[7.069,-0.368,-0.368,7.462,0.368,0.368]],"slots":["body","screws"]},"aero-750-gas-block":{"part":"aero-750-gas-block","model":"aero-750-gas-block.glb","script":"aero_750_gas_block.py","inputs":{"aero-750-gas-block.boss_width":0.33,"aero-750-gas-block.edge_break":0.012,"aero-750-gas-block.height_above_bore":0.79,"aero-750-gas-block.journal_id":0.75,"aero-750-gas-block.length":1.013,"aero-750-gas-block.od":0.884,"aero-750-gas-block.pin_hole_d":0.078,"aero-750-gas-block.pin_hole_from_front":0.326,"aero-750-gas-block.pin_to_port":0.418,"aero-750-gas-block.port_from_rear":0.269,"aero-750-gas-block.set_screw_d":0.185,"aero-750-gas-block.set_screw_end_d":0.15,"aero-750-gas-block.set_screw_from_front":0.258,"aero-750-gas-block.set_screw_key":0.09375,"aero-750-gas-block.set_screw_length":0.1875,"aero-750-gas-block.tab_below_bore":0.568,"aero-750-gas-block.tube_hole_above_bore":0.625,"aero-750-gas-block.tube_hole_d":0.1805,"aero-750-gas-block.tube_hole_past_pin":0.217},"profiles":{"front":[[-0.443,-0.049],[-0.427,-0.132],[-0.384,-0.233],[-0.326,-0.312],[-0.258,-0.375],[-0.215,-0.428],[-0.177,-0.496],[-0.154,-0.557],[-0.13,-0.576],[0.065,-0.576],[0.12,-0.574],[0.144,-0.562],[0.192,-0.453],[0.233,-0.403],[0.334,-0.309],[0.395,-0.228],[0.443,-0.107],[0.453,-0.051],[0.453,0.037],[0.448,0.04],[0.45,0.004],[0.445,0.004],[0.445,0.052],[0.427,0.131],[0.397,0.199],[0.402,0.204],[0.392,0.207],[0.367,0.247],[0.379,0.245],[0.245,0.406],[0.23,0.414],[0.207,0.46],[0.182,0.551],[0.175,0.657],[0.149,0.712],[0.159,0.707],[0.154,0.72],[0.142,0.725],[0.147,0.73],[0.123,0.754],[0.087,0.777],[0.006,0.792],[-0.067,0.769],[-0.111,0.733],[-0.134,0.7],[-0.149,0.657],[-0.167,0.523],[-0.205,0.434],[-0.26,0.358],[-0.359,0.255],[-0.407,0.169],[-0.44,0.052]]},"features":{"front":{}},"placement":{"front":{"plane":"zy","offset":{}}},"bounds":{"min":[-0.269,-0.568,-0.442],"max":[0.744,0.79,0.442]},"volume_in3":0.32,"centroid":[0.2401,0.094,0],"shell":[0.2455,0.0797,0],"area_in2":7.3473,"triangles":4904,"manifold":true,"slabs":[[-0.269,-0.568,-0.378,0.744,-0.229,0.378],[-0.269,-0.229,-0.442,0.744,0.451,0.442],[-0.269,0.451,-0.204,0.744,0.79,0.204]],"slots":["body"]},"aero-ar15-front-sight-post-kit":{"part":"aero-ar15-front-sight-post-kit","model":"aero-ar15-front-sight-post-kit.glb","script":"aero_ar15_front_sight_post_kit.py","inputs":{"aero-ar15-front-sight-post-kit.blade_height":0.268,"aero-ar15-front-sight-post-kit.blade_width":0.07,"aero-ar15-front-sight-post-kit.end_chamfer":0.025,"aero-ar15-front-sight-post-kit.flange_d":0.3645,"aero-ar15-front-sight-post-kit.flange_thickness":0.06,"aero-ar15-front-sight-post-kit.height":0.101,"aero-ar15-front-sight-post-kit.notch_circle_d":0.4,"aero-ar15-front-sight-post-kit.notch_r":0.04675,"aero-ar15-front-sight-post-kit.relief_length":0.062,"aero-ar15-front-sight-post-kit.seat_below_tower_top":0.227,"aero-ar15-front-sight-post-kit.shank_length":0.46,"aero-ar15-front-sight-post-kit.thread_major_d":0.16045,"aero-ar15-front-sight-post-kit.thread_pitch":0.027778,"aero-ar15-front-sight-post-kit.thread_pitch_d":0.1438},"profiles":{},"features":{},"placement":{},"bounds":{"min":[-0.1775,-0.687,-0.1775],"max":[0.1775,0.101,0.1775]},"volume_in3":0.0143,"centroid":[0.0001,-0.3131,0],"shell":[0.0001,-0.3081,-0.0002],"area_in2":0.6378,"triangles":3932,"manifold":true,"slabs":[[-0.08,-0.687,-0.08,0.08,-0.293,0.08],[-0.178,-0.293,-0.178,0.178,0.101,0.178]],"slots":["post"]},"aero-carbine-gas-tube":{"part":"aero-carbine-gas-tube","model":"aero-carbine-gas-tube.glb","script":"aero_carbine_gas_tube.py","inputs":{"aero-carbine-gas-tube.bend_end_from_rear":5.53,"aero-carbine-gas-tube.bend_offset":0.156,"aero-carbine-gas-tube.bend_radius":3.6,"aero-carbine-gas-tube.bend_start_from_rear":3.71,"aero-carbine-gas-tube.bore":0.134,"aero-carbine-gas-tube.crimp_depth":0.011,"aero-carbine-gas-tube.crimp_front_from_front":0.08,"aero-carbine-gas-tube.crimp_rear_from_front":0.295,"aero-carbine-gas-tube.crimp_width":0.035,"aero-carbine-gas-tube.end_break":0.015,"aero-carbine-gas-tube.gas_hole_d":0.125,"aero-carbine-gas-tube.gas_hole_from_front":0.605,"aero-carbine-gas-tube.head_length":0.1,"aero-carbine-gas-tube.length":9.75,"aero-carbine-gas-tube.od":0.18,"aero-carbine-gas-tube.pin_hole_d":0.078,"aero-carbine-gas-tube.pin_hole_from_front":0.187,"aero-carbine-gas-tube.plug_length":0.44,"aero-carbine-gas-tube.relief_depth":0.013,"aero-carbine-gas-tube.relief_end_from_rear":2.27},"profiles":{"side":[[0,0.129],[0.023,0.107],[0,0.084],[0,0.062],[0.011,0.05],[0.012,0.017],[0.028,0],[0.073,0],[0.085,0.011],[0.118,0.012],[0.13,0],[0.141,0.012],[0.163,0],[0.174,0.012],[0.242,0.012],[0.264,0.001],[0.287,0.012],[0.332,0.012],[0.343,0.001],[0.377,0.001],[0.399,0.001],[0.41,0.012],[0.489,0.013],[0.568,0.002],[0.579,0.013],[0.658,0.013],[0.702,0.013],[0.714,0.002],[0.792,0.002],[0.804,0.014],[0.882,0.014],[0.905,0.003],[1.242,0.004],[1.253,0.015],[1.298,0.015],[1.331,0.015],[1.343,0.004],[1.421,0.004],[1.444,0.016],[1.466,0.005],[1.511,0.005],[1.522,0.016],[1.545,0.016],[1.556,0.005],[3.915,0.012],[3.926,0.001],[3.949,0.012],[4.466,0.014],[4.477,0.025],[4.6,0.026],[4.611,0.037],[4.701,0.037],[4.713,0.048],[4.802,0.049],[4.814,0.06],[4.926,0.06],[4.937,0.072],[5.016,0.072],[5.027,0.083],[5.128,0.083],[5.139,0.095],[5.195,0.095],[5.207,0.106],[5.319,0.106],[5.33,0.118],[5.521,0.13],[5.532,0.141],[5.611,0.141],[5.622,0.152],[5.734,0.153],[5.746,0.164],[6.004,0.165],[6.015,0.176],[6.914,0.179],[6.925,0.168],[7.262,0.169],[7.442,0.169],[7.453,0.181],[7.487,0.181],[9.115,0.186],[9.127,0.175],[9.194,0.175],[9.205,0.186],[9.239,0.186],[9.25,0.175],[9.688,0.176],[9.7,0.165],[9.722,0.165],[9.739,0.182],[9.739,0.227],[9.75,0.238],[9.739,0.261],[9.75,0.283],[9.75,0.317],[9.71,0.345],[9.699,0.334],[9.677,0.334],[7.441,0.327],[7.43,0.338],[5.869,0.333],[5.857,0.322],[5.689,0.321],[5.678,0.31],[5.599,0.31],[5.588,0.298],[5.476,0.298],[5.464,0.287],[5.408,0.286],[5.397,0.275],[5.296,0.275],[5.285,0.264],[5.172,0.263],[5.161,0.252],[5.116,0.252],[5.105,0.241],[4.97,0.24],[4.959,0.229],[4.892,0.229],[4.881,0.217],[4.667,0.206],[4.656,0.194],[4.589,0.194],[4.577,0.183],[4.487,0.183],[4.476,0.171],[1.118,0.161],[1.106,0.172],[1.016,0.172],[0.331,0.169],[0.32,0.158],[0.298,0.158],[0.253,0.18],[0.241,0.169],[0.028,0.168]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{}}},"bounds":{"min":[-0.605,-0.09,-0.09],"max":[9.145,0.246,0.09]},"volume_in3":0.10753,"centroid":[3.7924,0.0649,0],"shell":[4.3067,0.0744,0],"area_in2":9.4094,"triangles":6148,"manifold":true,"slabs":[[-0.605,-0.09,-0.09,4.465,0.162,0.09],[4.465,-0.019,-0.09,5.245,0.241,0.09],[5.245,0.061,-0.09,9.145,0.246,0.09]],"slots":["tube"]},"aero-charging-handle":{"part":"aero-charging-handle","model":"aero-charging-handle.glb","script":"aero_charging_handle.py","inputs":{"aero-charging-handle.catch_bottom":0.1,"aero-charging-handle.catch_thickness":0.123,"aero-charging-handle.guide_lug_height":0.119,"aero-charging-handle.length":5.895,"aero-charging-handle.shaft_thickness":0.2985,"aero-charging-handle.shaft_width":0.4,"aero-charging-handle.shoulder_break_angle":47,"aero-charging-handle.shoulder_break_height":0.083,"aero-charging-handle.t_block_length":0.425,"aero-charging-handle.t_height":0.4235,"aero-charging-handle.t_nest_apex":0.78,"aero-charging-handle.t_nest_r":0.437,"std.ar15.charging_handle_axis_y":1.7338,"std.ar15.charging_handle_channel_rear_half_width":0.209,"std.ar15.charging_handle_channel_rear_round_x":0.676,"std.ar15.charging_handle_channel_round_r":0.2665,"std.ar15.charging_handle_latch_slot_bottom_y":1.52,"std.ar15.charging_handle_latch_slot_floor":0.045,"std.ar15.charging_handle_latch_slot_length":0.195,"std.ar15.charging_handle_latch_slot_top_y":1.935,"std.ar15.charging_handle_latch_slot_wall":0.156,"std.ar15.charging_handle_notch_chamfer":0.083,"std.ar15.charging_handle_notch_floor_y":1.571,"std.ar15.charging_handle_notch_roof_y":1.89,"std.ar15.rail_tongue_half_width":0.318},"profiles":{"top":[[-0.869,0.832],[-0.869,-0.64],[-0.862,-0.655],[-0.869,-0.662],[-0.869,-0.699],[-0.862,-0.706],[-0.862,-0.766],[-0.869,-0.788],[-0.862,-0.795],[-0.862,-0.854],[-0.854,-0.876],[-0.832,-0.921],[-0.784,-0.969],[-0.703,-1.006],[-0.621,-1.006],[-0.555,-0.976],[-0.518,-0.947],[-0.503,-0.947],[-0.47,-0.913],[-0.44,-0.862],[-0.44,-0.84],[-0.433,-0.832],[-0.433,-0.684],[-0.425,-0.677],[-0.433,-0.64],[-0.425,-0.632],[-0.418,-0.573],[-0.396,-0.521],[-0.381,-0.507],[-0.385,-0.496],[-0.396,-0.499],[-0.396,-0.492],[-0.374,-0.462],[-0.303,-0.399],[-0.237,-0.362],[-0.17,-0.34],[-0.126,-0.34],[-0.118,-0.333],[0,-0.333],[0.015,-0.325],[0.022,-0.207],[0.192,-0.207],[0.2,-0.2],[4.312,-0.2],[4.32,-0.207],[4.371,-0.207],[4.379,-0.2],[4.386,-0.207],[4.394,-0.2],[4.475,-0.2],[4.482,-0.207],[4.549,-0.214],[4.593,-0.229],[4.608,-0.244],[4.823,-0.244],[4.904,-0.207],[4.985,-0.207],[4.993,-0.2],[5.015,-0.207],[5.791,-0.207],[5.854,-0.152],[5.877,-0.115],[5.899,-0.041],[5.899,0.026],[5.891,0.033],[5.884,0.085],[5.862,0.129],[5.799,0.192],[4.948,0.192],[4.941,0.2],[4.882,0.207],[4.823,0.237],[4.749,0.237],[4.741,0.244],[4.608,0.244],[4.556,0.214],[4.512,0.2],[4.453,0.2],[4.445,0.192],[4.43,0.2],[4.379,0.192],[4.371,0.2],[4.334,0.2],[4.32,0.192],[4.312,0.2],[0.281,0.2],[0.266,0.192],[0.274,0.207],[0.366,0.285],[0.374,0.359],[0.366,0.374],[0.348,0.392],[0.325,0.399],[0.274,0.399],[0.266,0.407],[0.229,0.407],[0.222,0.414],[0.104,0.422],[0.059,0.436],[-0.104,0.451],[-0.111,0.459],[-0.133,0.459],[-0.2,0.496],[-0.248,0.558],[-0.263,0.603],[-0.263,0.64],[-0.285,0.669],[-0.285,0.684],[-0.274,0.695],[-0.259,0.695],[-0.24,0.721],[-0.255,0.751],[-0.237,0.769],[-0.222,0.769],[-0.211,0.788],[-0.218,0.832],[-0.181,0.854],[-0.174,0.899],[-0.181,0.906],[-0.189,0.95],[-0.222,0.991],[-0.259,1.013],[-0.325,1.021],[-0.333,1.028],[-0.385,1.028],[-0.392,1.036],[-0.451,1.036],[-0.459,1.043],[-0.54,1.05],[-0.577,1.036],[-0.607,0.991],[-0.725,0.991],[-0.777,0.969],[-0.84,0.906],[-0.854,0.884],[-0.862,0.84]]},"features":{"top":{}},"placement":{"top":{"plane":"xz","offset":{}}},"bounds":{"min":[-0.869,-0.1493,-1.05],"max":[5.899,0.2743,1.006]},"volume_in3":1.1817,"centroid":[1.5274,0.0141,-0.0315],"shell":[1.6734,0.0158,-0.031],"area_in2":13.3186,"triangles":4480,"manifold":true,"slabs":[[-0.869,-0.149,-1.05,-0.471,0.274,1.006],[-0.471,-0.149,-1.044,-0.073,0.274,0.914],[-0.073,-0.149,-0.448,0.325,0.149,0.333],[0.325,-0.149,-0.399,0.723,0.149,0.2],[0.723,-0.149,-0.244,5.103,0.149,0.244],[5.103,-0.149,-0.192,5.899,0.149,0.2]],"slots":["body"]},"aero-enhanced-15-handguard":{"part":"aero-enhanced-15-handguard","model":"aero-enhanced-15-handguard.glb","script":"aero_enhanced_15_handguard.py","inputs":{"aero-enhanced-15-handguard.bottom_flat_width":0.88,"aero-enhanced-15-handguard.channel_roof_below_rail_top":0.165,"aero-enhanced-15-handguard.channel_width":0.5,"aero-enhanced-15-handguard.height":2.18,"aero-enhanced-15-handguard.inside_diameter":1.72,"aero-enhanced-15-handguard.mlok_bottom_slots":7,"aero-enhanced-15-handguard.mlok_slot0_from_rear":4.727,"aero-enhanced-15-handguard.mlok_slots":7,"aero-enhanced-15-handguard.neck_width":0.67,"aero-enhanced-15-handguard.nut_cut_depth":1.6,"aero-enhanced-15-handguard.nut_cut_diameter":1.78,"aero-enhanced-15-handguard.overall_length":15.14,"aero-enhanced-15-handguard.rail_rear_from_rear":0.11,"aero-enhanced-15-handguard.rail_slot0_from_rear":0.634,"aero-enhanced-15-handguard.rail_slots":37,"aero-enhanced-15-handguard.rail_top_above_bore":1.2125,"aero-enhanced-15-handguard.rail_window0_lug":5,"aero-enhanced-15-handguard.rail_window_length":0.54,"aero-enhanced-15-handguard.rail_window_width":0.36,"aero-enhanced-15-handguard.rail_windows":17,"aero-enhanced-15-handguard.rear_bottom_ahead":0.235,"aero-enhanced-15-handguard.rear_notch_width":1.05,"aero-enhanced-15-handguard.rear_x":-0.555,"aero-enhanced-15-handguard.ridge_across":1.44,"aero-enhanced-15-handguard.ridge_from_bore":0.79,"aero-enhanced-15-handguard.screw_countersink_d":0.27,"aero-enhanced-15-handguard.screw_hole0_from_rear":0.824,"aero-enhanced-15-handguard.screw_hole_d":0.14,"aero-enhanced-15-handguard.screw_hole_spacing":0.41,"aero-enhanced-15-handguard.shelf_below_rail_top":0.235,"aero-enhanced-15-handguard.side_flat_height":0.93,"aero-enhanced-15-handguard.socket_boss_d":0.67,"aero-enhanced-15-handguard.socket_boss_height":0.087,"aero-enhanced-15-handguard.socket_cup_d":0.484,"aero-enhanced-15-handguard.socket_cup_from_rear":2.918,"aero-enhanced-15-handguard.socket_cup_height":0.084,"aero-enhanced-15-handguard.socket_from_rear":2.863,"aero-enhanced-15-handguard.socket_hole_d":0.36,"aero-enhanced-15-handguard.vent_shallow_row_from_ridge":0.17,"aero-enhanced-15-handguard.vent_slot0_from_rear":2.22,"aero-enhanced-15-handguard.vent_slot_length":0.82,"aero-enhanced-15-handguard.vent_slot_pitch":0.953,"aero-enhanced-15-handguard.vent_slot_width":0.2,"aero-enhanced-15-handguard.vent_slots":14,"aero-enhanced-15-handguard.vent_steep_row_from_flat":0.14,"aero-enhanced-15-handguard.width":1.92,"std.mlok.slot_corner_r":0.0937007874015748,"std.mlok.slot_length":1.2598425196850394,"std.mlok.slot_pitch":1.574803149606299,"std.mlok.slot_width":0.2755905511811024,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{},"features":{},"placement":{},"bounds":{"min":[-0.555,-1.0515,-1.047],"max":[14.585,1.2125,1.047]},"volume_in3":7.5615,"centroid":[6.4471,0.108,0],"shell":[6.8494,0.1177,0],"area_in2":183.834,"triangles":48272,"manifold":true,"slabs":[[-0.555,-0.967,-0.96,1.836,1.212,0.96],[1.836,-1.051,-1.047,2.632,1.212,1.047],[2.632,-0.967,-1.047,3.031,1.212,1.047],[3.031,-0.967,-0.96,14.585,1.212,0.96]],"slots":["body","screws","socket"]},"aero-m4e1-enhanced-upper.receiver":{"part":"aero-m4e1-enhanced-upper","component":"receiver","model":"aero-m4e1-enhanced-upper.receiver.glb","script":"aero_m4e1_enhanced_upper.py","inputs":{"aero-m4e1-enhanced-upper.body_radius":0.59,"aero-m4e1-enhanced-upper.bore_axis_above_pin":0.8775,"aero-m4e1-enhanced-upper.bore_d":1,"aero-m4e1-enhanced-upper.cam_boss_bottom_y":1.21,"aero-m4e1-enhanced-upper.cam_boss_ear_half_width":0.373,"aero-m4e1-enhanced-upper.cam_boss_face_half_width":0.172,"aero-m4e1-enhanced-upper.cam_boss_face_top_y":1.519,"aero-m4e1-enhanced-upper.cam_boss_flank_run":0.135,"aero-m4e1-enhanced-upper.cam_boss_top_half_width":0.245,"aero-m4e1-enhanced-upper.cam_boss_top_y":1.648,"aero-m4e1-enhanced-upper.cam_boss_x":5.14,"aero-m4e1-enhanced-upper.deflector_out":1.47,"aero-m4e1-enhanced-upper.deflector_point_x":2.72,"aero-m4e1-enhanced-upper.deflector_point_y":1.16,"aero-m4e1-enhanced-upper.dovetail_foot_half_width":0.323,"aero-m4e1-enhanced-upper.dovetail_foot_y":1.885,"aero-m4e1-enhanced-upper.fa_axis_angle":20,"aero-m4e1-enhanced-upper.fa_bore_d":0.509,"aero-m4e1-enhanced-upper.fa_bore_depth":0.65,"aero-m4e1-enhanced-upper.fa_housing_front_x":1.9,"aero-m4e1-enhanced-upper.fa_housing_out_rear":1.67,"aero-m4e1-enhanced-upper.fa_housing_outer_bottom_y":0.92,"aero-m4e1-enhanced-upper.fa_housing_outer_top_y":1.2,"aero-m4e1-enhanced-upper.fa_housing_r":0.3125,"aero-m4e1-enhanced-upper.fa_inner_bore_d":0.315,"aero-m4e1-enhanced-upper.fa_rear_x":-0.395,"aero-m4e1-enhanced-upper.fa_rear_z":1.09,"aero-m4e1-enhanced-upper.front_face_x":7.036,"aero-m4e1-enhanced-upper.handle_seat_x":0.092,"aero-m4e1-enhanced-upper.left_pad_front_x":6.202,"aero-m4e1-enhanced-upper.left_pad_rear_x":3.077,"aero-m4e1-enhanced-upper.left_pad_step_front_x":4.585,"aero-m4e1-enhanced-upper.left_pad_step_rear_x":4.05,"aero-m4e1-enhanced-upper.left_pad_step_top_y":0.743,"aero-m4e1-enhanced-upper.left_pad_top_y":0.662,"aero-m4e1-enhanced-upper.lug_wall_half_width":0.453,"aero-m4e1-enhanced-upper.platform_bore_d":1.22,"aero-m4e1-enhanced-upper.platform_front_x":7.925,"aero-m4e1-enhanced-upper.platform_groove0_x":6.722,"aero-m4e1-enhanced-upper.platform_groove_depth":0.125,"aero-m4e1-enhanced-upper.platform_groove_pitch":0.2016,"aero-m4e1-enhanced-upper.platform_groove_width":0.1,"aero-m4e1-enhanced-upper.platform_grooves":6,"aero-m4e1-enhanced-upper.platform_hole0_x":7.341,"aero-m4e1-enhanced-upper.platform_hole_above_bore":0.6155,"aero-m4e1-enhanced-upper.platform_hole_d":0.1,"aero-m4e1-enhanced-upper.platform_hole_spacing":0.414,"aero-m4e1-enhanced-upper.platform_holes":8,"aero-m4e1-enhanced-upper.platform_od":1.77,"aero-m4e1-enhanced-upper.port_bottom_y":0.841,"aero-m4e1-enhanced-upper.port_end_r":0.25,"aero-m4e1-enhanced-upper.port_front_x":6.036,"aero-m4e1-enhanced-upper.port_length":3.125,"aero-m4e1-enhanced-upper.rail_front_x":6.591,"aero-m4e1-enhanced-upper.rail_neck_bottom_y":1.737,"aero-m4e1-enhanced-upper.rail_neck_half_width":0.309,"aero-m4e1-enhanced-upper.rail_tongue_rear_x":-0.6,"aero-m4e1-enhanced-upper.rail_top_above_pin":2.09,"aero-m4e1-enhanced-upper.receiver_rear_x":-0.621,"aero-m4e1-enhanced-upper.shoulder_bottom_y":0.875,"aero-m4e1-enhanced-upper.shoulder_x":6.591,"aero-m4e1-enhanced-upper.side_bottom_y":1.435,"aero-m4e1-enhanced-upper.side_half_width":0.42,"aero-m4e1-enhanced-upper.underside_y":0.2485,"std.ar15.bore_axis_y":0.8775,"std.ar15.buffer_tower_front_x":-0.628,"std.ar15.buffer_tower_od":1.392,"std.ar15.buffer_trough_r":0.5625,"std.ar15.charging_handle_channel_floor_y":1.5845,"std.ar15.charging_handle_channel_front_round_x":5.726,"std.ar15.charging_handle_channel_rear_half_width":0.209,"std.ar15.charging_handle_channel_rear_round_x":0.676,"std.ar15.charging_handle_channel_roof_y":1.9085,"std.ar15.charging_handle_channel_round_r":0.2665,"std.ar15.charging_handle_channel_slot_half_width":0.205,"std.ar15.charging_handle_channel_tier_half_width":0.25,"std.ar15.charging_handle_channel_tier_top_y":1.7115,"std.ar15.charging_handle_channel_top_half_width":0.22,"std.ar15.charging_handle_latch_slot_bottom_y":1.52,"std.ar15.charging_handle_latch_slot_floor":0.045,"std.ar15.charging_handle_latch_slot_length":0.195,"std.ar15.charging_handle_latch_slot_top_y":1.935,"std.ar15.charging_handle_latch_slot_wall":0.156,"std.ar15.charging_handle_notch_chamfer":0.083,"std.ar15.charging_handle_notch_floor_y":1.571,"std.ar15.charging_handle_notch_roof_y":1.89,"std.ar15.deck_y":0.2485,"std.ar15.front_lug_slot_width":0.5,"std.ar15.rail_tongue_end_r":0.4175,"std.ar15.rail_tongue_fillet_r":0.1476,"std.ar15.rail_tongue_front_x":0.277,"std.ar15.rail_tongue_half_width":0.318,"std.ar15.rail_tongue_shoulder_x":0.4165,"std.ar15.rear_lug_slot_rear_x":-0.402,"std.ar15.rear_lug_slot_width":0.5,"std.ar15.rear_wall_arc_r":0.75,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.top_width":0.835},"profiles":{"side":[[-0.657,1.25],[-0.641,1.135],[-0.646,0.923],[-0.597,0.727],[-0.532,0.586],[-0.472,0.51],[-0.365,0.409],[-0.238,0.33],[-0.237,-0.094],[-0.226,-0.208],[-0.213,-0.216],[0.234,-0.211],[0.236,0.227],[0.255,0.241],[6.122,0.252],[6.146,0.244],[6.146,-0.001],[6.163,-0.072],[6.231,-0.167],[6.34,-0.221],[6.46,-0.221],[6.53,-0.188],[6.593,-0.099],[6.601,-0.02],[7.869,-0.013],[7.899,0.028],[7.92,0.256],[7.994,0.276],[8.018,0.354],[8.013,0.436],[7.928,0.466],[7.925,0.501],[8.004,0.504],[8.029,0.523],[8.034,0.632],[8.034,0.763],[7.966,0.771],[7.936,0.795],[7.936,0.964],[8.034,0.975],[8.028,1.22],[7.925,1.252],[7.927,1.293],[7.987,1.293],[8.017,1.312],[8.023,1.394],[8.012,1.454],[7.987,1.489],[7.919,1.497],[7.886,1.753],[7.856,1.777],[7.786,1.777],[7.767,1.649],[7.693,1.641],[7.68,1.655],[7.674,1.769],[7.584,1.777],[7.571,1.649],[7.481,1.646],[7.473,1.769],[7.383,1.777],[7.369,1.649],[7.296,1.641],[7.277,1.649],[7.271,1.769],[7.187,1.777],[7.173,1.763],[7.168,1.649],[7.084,1.641],[7.07,1.769],[6.986,1.777],[6.967,1.649],[6.888,1.64],[6.869,1.659],[6.869,1.768],[6.784,1.776],[6.771,1.746],[6.771,1.654],[6.752,1.64],[6.681,1.64],[6.667,1.654],[6.662,1.768],[6.596,1.784],[6.602,2.084],[6.588,2.097],[6.397,2.086],[6.403,1.983],[6.256,1.972],[6.204,1.98],[6.191,2.092],[6.033,2.097],[5.998,2.072],[6.014,2.012],[6.006,1.977],[5.886,1.971],[5.807,1.98],[5.807,2.078],[5.783,2.097],[5.625,2.091],[5.6,2.066],[5.617,2.05],[5.614,1.977],[5.494,1.971],[5.41,1.979],[5.41,2.083],[5.391,2.096],[5.244,2.096],[5.214,2.072],[5.225,1.984],[5.189,1.971],[5.015,1.976],[5.004,2.09],[4.846,2.096],[4.822,2.077],[4.819,1.976],[4.683,1.97],[4.615,1.978],[4.607,2.09],[4.455,2.095],[4.43,2.082],[4.428,1.976],[4.248,1.97],[4.218,1.984],[4.215,2.09],[4.041,2.09],[4.025,1.97],[3.829,1.97],[3.818,2.089],[3.671,2.095],[3.641,2.081],[3.633,1.975],[3.502,1.969],[3.429,1.983],[3.429,2.081],[3.399,2.094],[3.252,2.089],[3.236,1.974],[3.051,1.974],[3.032,1.982],[3.037,2.075],[3.018,2.094],[2.876,2.094],[2.847,2.08],[2.844,1.974],[2.659,1.968],[2.634,1.982],[2.645,2.075],[2.626,2.094],[2.468,2.093],[2.449,2.08],[2.441,1.968],[2.256,1.968],[2.243,1.982],[2.245,2.082],[2.076,2.093],[2.057,2.079],[2.049,1.973],[1.864,1.968],[1.851,1.976],[1.862,2.019],[1.851,2.041],[1.867,2.058],[1.853,2.082],[1.679,2.093],[1.66,2.079],[1.652,1.973],[1.483,1.967],[1.453,1.976],[1.47,1.992],[1.462,2.082],[1.282,2.092],[1.268,2.079],[1.263,1.975],[1.228,1.967],[1.059,1.978],[1.078,1.986],[1.083,2.062],[1.037,2.092],[-0.536,2.091],[-0.579,2.085],[-0.604,2.055],[-0.609,1.925],[-0.595,1.911],[-0.552,1.911],[-0.525,1.889],[0.014,1.89],[0.088,1.816],[0.088,1.664],[0.009,1.58],[-0.628,1.579],[-0.641,1.544]]},"features":{"side":{"forward_assist_housing":[[[-0.631,1.448],[1.773,1.45],[1.899,1.349],[1.9,0.845],[1.522,0.718],[0.009,0.524],[-0.496,0.507],[-0.63,0.658]]],"deflector":[[[1.874,1.366],[2.32,1.585],[2.555,1.669],[2.74,1.619],[2.95,1.468],[2.951,0.846],[2.53,0.846],[1.899,1.097]]]}},"placement":{"side":{"plane":"xy","offset":{}}},"bounds":{"min":[-0.621,-0.221,-0.885],"max":[7.925,2.09,1.5179]},"volume_in3":7.359,"centroid":[3.8675,0.9923,0.0965],"shell":[3.5756,1.0684,0.0508],"area_in2":92.9364,"triangles":20226,"manifold":true,"rear_corner":{"r":0.75,"centre":[0.122,0.9985],"x":[-0.628,-0.0116],"reach_z":0.696,"trough_r":0.5625},"slabs":[[-0.621,-0.14,-0.59,-0.233,2.09,1.436],[-0.233,-0.216,-0.59,0.156,2.09,1.518],[0.156,-0.212,-0.59,0.544,2.09,1.387],[0.544,0.249,-0.59,0.933,1.972,1.246],[0.933,0.249,-0.59,1.321,1.972,1.104],[1.321,0.249,-0.59,2.098,1.972,0.963],[2.098,0.249,-0.59,2.487,1.972,1.266],[2.487,0.249,-0.59,2.875,1.972,1.47],[2.875,0.249,-0.59,3.264,1.972,0.731],[3.264,0.249,-0.59,5.983,1.972,0.59],[5.983,-0.221,-0.59,6.371,1.972,0.59],[6.371,-0.221,-0.885,6.76,1.972,0.885],[6.76,-0.007,-0.885,7.925,1.763,0.885]],"slots":["receiver"]},"aero-m4e1-lower.grip":{"part":"aero-m4e1-lower","component":"grip","model":"aero-m4e1-lower.grip.glb","script":"aero_m4e1_lower.py","inputs":{"aero-m4e1-lower.grip_body_width":0.885,"aero-m4e1-lower.grip_depth":2.153,"aero-m4e1-lower.grip_height":3.709,"aero-m4e1-lower.grip_rake":28.3,"aero-m4e1-lower.grip_top_slope":1.7,"aero-m4e1-lower.grip_top_y":-1.221,"aero-m4e1-lower.grip_width":1.27,"aero-m4e1-lower.tower_top_above_pin":1.554,"cmmg-lower-parts-kit.grip_rake":30},"profiles":{"complete":[[-8.594,1.033],[-8.546,0.733],[-8.548,0.401],[-8.515,0.302],[-8.532,0.186],[-8.484,-0.114],[-8.501,-0.213],[-8.468,-0.263],[-8.485,-0.363],[-8.453,-0.462],[-8.454,-0.794],[-8.421,-0.828],[-8.439,-0.994],[-8.39,-1.226],[-8.408,-1.425],[-8.375,-1.459],[-8.376,-1.774],[-8.343,-1.808],[-8.345,-2.123],[-8.312,-2.156],[-8.329,-2.256],[-8.28,-2.422],[-8.297,-2.472],[-8.233,-2.837],[-8.249,-2.887],[-8.216,-2.921],[-8.185,-3.253],[-8.077,-3.345],[-7.828,-3.346],[-7.787,-3.305],[-7.619,-3.057],[-7.669,-2.99],[-7.667,-2.641],[-7.36,-2.585],[-7.293,-2.602],[-6.549,-1.601],[-6.408,-1.461],[-5.809,-1.248],[-4.759,-0.573],[-3.365,-0.564],[-3.142,-0.789],[-3.102,-1.129],[-3.077,-1.022],[-3.027,-0.989],[-2.925,-0.641],[-2.683,-0.368],[-2.384,-0.237],[-1.72,-0.24],[-1.677,-0.083],[-1.684,0.291],[-1.625,0.282],[-1.601,0.174],[-1.253,0.173],[-1.248,-0.5],[-1.223,-0.525],[-1.123,-0.509],[-0.858,-0.543],[-0.609,-0.644],[-0.37,-0.886],[-0.28,-1.094],[-0.139,-1.103],[-0.296,-1.111],[-0.338,-1.152],[-0.323,-1.418],[-0.407,-1.7],[-2.181,-4.347],[-2.198,-4.446],[-1.974,-4.539],[-0.681,-4.861],[-0.349,-4.929],[-0.183,-4.93],[-0.008,-4.773],[-0.008,-4.707],[-0.123,-4.556],[-0.123,-4.44],[0.414,-3.414],[0.556,-3.29],[0.805,-3.308],[0.846,-3.267],[0.847,-3.2],[0.715,-3.05],[0.699,-2.901],[1.009,-2.329],[1.142,-2.314],[1.158,-2.347],[1.307,-2.381],[2.187,-2.535],[2.353,-2.536],[6.174,-1.875],[6.183,-1.767],[6.085,-1.518],[6.089,-0.671],[6.207,-0.422],[6.315,-0.315],[6.523,-0.192],[6.574,-0.092],[6.574,-0.009],[6.541,0.074],[6.401,0.182],[3.595,0.214],[3.562,0.28],[3.48,0.297],[3.372,0.373],[3.356,0.572],[3.249,0.664],[3.116,0.648],[3.024,0.54],[3.023,0.325],[3.081,0.216],[2.334,0.22],[2.342,0.278],[2.301,0.32],[1.689,0.688],[1.589,0.689],[1.481,0.598],[1.255,0.226],[-0.073,0.249],[-0.371,0.417],[-0.577,0.709],[-0.576,0.974],[-0.626,0.991],[-0.625,1.107],[-0.608,1.257],[-0.575,1.256],[-0.559,1.024],[-0.541,1.256],[-0.566,1.314],[-0.624,1.323],[-0.631,1.547],[-1.046,1.549],[-1.229,1.501],[-1.262,1.534],[-1.561,1.535],[-1.619,1.494],[-1.645,1.403],[-1.71,1.503],[-2.076,1.522],[-8.019,1.602],[-8.118,1.619],[-8.25,1.77],[-8.466,1.787],[-8.558,1.696],[-8.591,1.58]],"side":[[-1.167,0.722],[-1.145,-0.296],[-1.116,-0.502],[-0.821,-0.528],[-0.611,-0.621],[-0.414,-0.802],[-0.285,-1.059],[-0.112,-1.08],[-0.129,-1.24],[-0.079,-1.291],[-0.075,-1.371],[0.991,-1.987],[1.143,-1.979],[1.167,-2.324],[2.268,-2.512],[6.147,-1.85],[6.16,-1.753],[6.06,-1.458],[6.079,-0.609],[6.197,-0.391],[6.509,-0.148],[6.552,0.004],[6.501,0.13],[6.413,0.202],[5.926,0.245],[0.072,0.244],[-0.062,0.269],[-0.306,0.388],[-0.52,0.662],[-0.586,0.889],[-0.61,1.545],[-0.984,1.567],[-1.14,1.521]],"grip_section":[[0,-0.022],[0.036,-0.207],[0.111,-0.334],[0.297,-0.495],[0.451,-0.544],[0.452,-0.569],[0.604,-0.585],[0.643,-0.629],[0.856,-0.627],[0.886,-0.598],[0.995,-0.634],[1.2,-0.617],[1.24,-0.569],[1.261,-0.6],[1.322,-0.557],[1.37,-0.577],[1.457,-0.528],[1.956,-0.406],[2.146,-0.225],[2.155,-0.003],[2.138,0.223],[2.044,0.279],[1.949,0.403],[1.287,0.573],[1.272,0.604],[1.211,0.617],[1.212,0.584],[0.899,0.603],[0.873,0.634],[0.622,0.609],[0.559,0.565],[0.476,0.577],[0.43,0.539],[0.306,0.521],[0.078,0.28],[0.015,0.125]],"grip_front":[[-0.686,-2.596],[-0.667,-3.36],[-0.61,-3.641],[-0.545,-3.747],[-0.391,-3.874],[-0.065,-3.878],[-0.038,-3.897],[0.327,-3.886],[0.429,-3.817],[0.515,-3.717],[0.553,-3.625],[0.594,-3.39],[0.621,-2.813],[0.594,-1.711],[0.53,-0.929],[0.439,-0.431],[0.446,-0.063],[0.41,-0.011],[0.315,0],[0,0],[-0.431,-0.017],[-0.446,-0.412],[-0.53,-0.792],[-0.617,-1.381],[-0.67,-2.038]]},"features":{"complete":{"grip":[[[-2.256,-1.208],[1.064,-1.226],[1.044,-5.094],[-2.276,-5.077]]],"stock":[[[-8.715,1.847],[-1.576,1.809],[-1.603,-3.42],[-8.742,-3.383]]],"tube":[[[-1.693,1.611],[-0.631,1.605],[-0.639,0.111],[-1.701,0.117]]],"guard_window":[[[1.5,-2.042],[1.504,-1.361],[1.537,-1.278],[1.696,-1.138],[1.829,-1.122],[1.853,-1.147],[1.769,-1.445],[1.784,-1.694],[1.932,-2.011],[2.072,-2.152],[2.105,-2.153],[2.131,-2.095],[2.015,-1.911],[1.967,-1.629],[2.018,-1.43],[2.177,-1.207],[2.293,-1.124],[3.024,-1.111],[3.206,-1.195],[3.297,-1.304],[3.313,-1.37],[3.31,-1.985],[3.259,-2.117],[3.184,-2.191],[3.018,-2.257],[2.353,-2.37],[2.154,-2.369],[1.723,-2.283],[1.549,-2.158]]],"stock_lever":[[[-5.842,-1.273],[-4.726,-0.565],[-3.365,-0.572],[-3.15,-0.789],[-3.119,-1.121],[-3.816,-1.134],[-4.231,-1.132],[-4.497,-1.147],[-5.663,-1.921],[-5.845,-1.854]]],"stock_lock_pin":[[[-4.231,-1.132],[-3.816,-1.134],[-3.818,-1.516],[-4.233,-1.514]]],"sling_loop":[[[-7.659,-2.641],[-7.31,-2.593],[-6.832,-3.26],[-6.916,-3.475],[-7.198,-3.474],[-7.661,-2.99]]]},"side":{"guard_window":[[[1.492,-1.934],[1.493,-1.379],[1.553,-1.219],[1.641,-1.14],[1.759,-1.098],[3.096,-1.102],[3.214,-1.161],[3.285,-1.241],[3.335,-1.401],[3.334,-1.888],[3.249,-2.099],[3.144,-2.178],[2.319,-2.336],[1.748,-2.242],[1.567,-2.145]]]},"grip_section":{},"grip_front":{}},"placement":{"complete":{"plane":"xy","offset":{}},"side":{"plane":"xy","offset":{}},"grip_section":{"plane":"xz","offset":{}},"grip_front":{"plane":"zy","offset":{"y":"grip_top_y"}}},"bounds":{"min":[-2.1977,-4.93,-0.634],"max":[1.064,-1.2248,0.634]},"volume_in3":6.4242,"centroid":[-0.4544,-3.2506,-0.0024],"shell":[-0.4325,-3.2276,-0.0024],"area_in2":22.2422,"triangles":1648,"manifold":true,"slabs":[[-1.892,-4.93,-0.604,-0.008,-4.559,0.582],[-2.198,-4.559,-0.634,0.008,-4.189,0.634],[-2.075,-4.189,-0.634,0.202,-3.818,0.634],[-1.827,-3.818,-0.634,0.396,-3.448,0.634],[-1.578,-3.448,-0.634,0.847,-3.077,0.634],[-1.33,-3.077,-0.634,0.804,-2.707,0.634],[-1.082,-2.707,-0.634,1.005,-2.336,0.634],[-0.833,-2.336,-0.634,1.064,-1.966,0.634],[-0.585,-1.966,-0.532,0.954,-1.595,0.508],[-0.376,-1.595,-0.446,0.313,-1.225,0.446]],"slots":["grip"]},"aero-m4e1-lower.receiver":{"part":"aero-m4e1-lower","component":"receiver","model":"aero-m4e1-lower.receiver.glb","script":"aero_m4e1_lower.py","inputs":{"aero-m4e1-lower.bolt_catch_boss_bottom_y":-0.02,"aero-m4e1-lower.bolt_catch_boss_front_x":3.52,"aero-m4e1-lower.bolt_catch_boss_out":0.708,"aero-m4e1-lower.bolt_catch_boss_rear_x":3.01,"aero-m4e1-lower.buffer_axis_above_pin":0.8775,"aero-m4e1-lower.catch_block_front_ramp":0.16,"aero-m4e1-lower.catch_block_front_x":3.64,"aero-m4e1-lower.catch_pad_bottom_y":-0.78,"aero-m4e1-lower.catch_pad_front_x":4.56,"aero-m4e1-lower.catch_pad_out":0.666,"aero-m4e1-lower.catch_pad_rear_x":3.048,"aero-m4e1-lower.catch_pad_top_y":-0.3,"aero-m4e1-lower.ear_left_out":0.542,"aero-m4e1-lower.ear_left_ramp":0.06,"aero-m4e1-lower.ear_left_rear_x":6.15,"aero-m4e1-lower.ear_right_out":0.519,"aero-m4e1-lower.ear_right_rear_x":6.18,"aero-m4e1-lower.front_view_lug_slot":0.549,"aero-m4e1-lower.panel_left_out":0.603,"aero-m4e1-lower.panel_left_ramp":0.08,"aero-m4e1-lower.panel_left_rear_x":3.03,"aero-m4e1-lower.panel_right_bottom_y":-1.03,"aero-m4e1-lower.panel_right_out":0.664,"aero-m4e1-lower.panel_right_ramp":0.17,"aero-m4e1-lower.panel_right_rear_x":3.09,"aero-m4e1-lower.rear_face_x":-1.14,"aero-m4e1-lower.tower_top_above_pin":1.554,"aero-m4e1-lower.wall_right_below_panel":0.56,"std.ar15.bolt_catch_plunger_hole_d":0.156,"std.ar15.bolt_catch_plunger_hole_depth":0.4703,"std.ar15.bolt_catch_plunger_hole_y":-0.195,"std.ar15.bolt_catch_slot_bottom_y":-0.38,"std.ar15.bolt_catch_slot_floor":0.4409,"std.ar15.bolt_catch_slot_front_x":3.375,"std.ar15.bolt_catch_slot_width":0.172,"std.ar15.bore_axis_y":0.8775,"std.ar15.buffer_tower_front_x":-0.628,"std.ar15.deck_front_x":6.194,"std.ar15.deck_y":0.2485,"std.ar15.fcg_pin_hole_d":0.15675,"std.ar15.fcg_pocket_corner_r":0.218,"std.ar15.fcg_pocket_depth":1.249,"std.ar15.fcg_pocket_front_x":3.11,"std.ar15.fcg_pocket_length":2.87,"std.ar15.fcg_pocket_width":0.69,"std.ar15.front_lug_slot_width":0.5,"std.ar15.hammer_pin_x":2.771,"std.ar15.hammer_pin_y":-0.375,"std.ar15.lower_body_width":0.88,"std.ar15.mag_catch_cbore_d":0.312,"std.ar15.mag_catch_cbore_depth":0.25,"std.ar15.mag_catch_fence_out":0.549,"std.ar15.mag_catch_hole_d":0.2055,"std.ar15.mag_catch_slot_bottom_y":-0.689,"std.ar15.mag_catch_slot_floor":0.3799,"std.ar15.mag_catch_slot_front_x":4.557,"std.ar15.mag_catch_slot_h":0.252,"std.ar15.mag_catch_slot_rear_x":3.048,"std.ar15.mag_catch_x":3.291,"std.ar15.mag_catch_y":-0.565,"std.ar15.mag_release_pocket_depth":0.617,"std.ar15.mag_release_pocket_h":0.515,"std.ar15.mag_release_pocket_w":0.319,"std.ar15.magwell_box_length":2.398,"std.ar15.magwell_corner_r":0.062,"std.ar15.magwell_front_inner_x":6.025,"std.ar15.magwell_length":2.553,"std.ar15.magwell_spine_slot_width":0.47,"std.ar15.magwell_width":0.898,"std.ar15.pin_spacing":6.375,"std.ar15.pivot_hole_d":0.251,"std.ar15.rear_lug_slot_depth":0.63,"std.ar15.rear_lug_slot_rear_x":-0.402,"std.ar15.rear_lug_slot_width":0.5,"std.ar15.rear_wall_arc_r":0.75,"std.ar15.safety_detent_boss_below_deck":0.455,"std.ar15.safety_detent_boss_face":0.53,"std.ar15.safety_detent_boss_from_rear":0.36,"std.ar15.safety_detent_boss_length":0.43,"std.ar15.selector_hole_d":0.376,"std.ar15.selector_x":0.803,"std.ar15.selector_y":-0.466,"std.ar15.takedown_hole_d":0.251,"std.ar15.trigger_pin_x":1.928,"std.ar15.trigger_pin_y":-0.689,"std.ar15.trigger_slot_front_ahead_of_pin":0.52,"std.ar15.trigger_slot_length":0.68,"std.ar15.trigger_slot_width":0.312,"std.ar15.upper_rear_face_x":-0.621,"std.receiver_extension.milspec_od":1.148},"profiles":{"side":[[-1.167,0.722],[-1.145,-0.296],[-1.116,-0.502],[-0.821,-0.528],[-0.611,-0.621],[-0.414,-0.802],[-0.285,-1.059],[-0.112,-1.08],[-0.129,-1.24],[-0.079,-1.291],[-0.075,-1.371],[0.991,-1.987],[1.143,-1.979],[1.167,-2.324],[2.268,-2.512],[6.147,-1.85],[6.16,-1.753],[6.06,-1.458],[6.079,-0.609],[6.197,-0.391],[6.509,-0.148],[6.552,0.004],[6.501,0.13],[6.413,0.202],[5.926,0.245],[0.072,0.244],[-0.062,0.269],[-0.306,0.388],[-0.52,0.662],[-0.586,0.889],[-0.61,1.545],[-0.984,1.567],[-1.14,1.521]],"rear":[[-0.682,-0.566],[-0.682,-0.754],[-0.42,-1.593],[-0.484,-1.672],[-0.574,-1.702],[-0.615,-1.751],[-0.607,-1.856],[-0.555,-1.923],[-0.532,-2.088],[-0.487,-2.156],[-0.547,-2.246],[-0.555,-2.336],[-0.472,-2.448],[-0.487,-2.531],[-0.555,-2.568],[-0.547,-2.621],[-0.487,-2.681],[-0.487,-3.625],[-0.54,-3.94],[-0.289,-3.982],[-0.206,-4.079],[0.266,-4.079],[0.349,-3.989],[0.645,-3.94],[0.645,-3.625],[0.555,-3.4],[0.555,-2.981],[0.562,-2.891],[0.667,-2.808],[0.667,-1.818],[0.562,-1.646],[0.454,-1.62],[0.435,-1.586],[0.66,-0.851],[0.682,-0.664],[0.63,-0.394],[0.424,-0.12],[0.289,0],[-0.004,0],[-0.296,0],[-0.487,-0.176],[-0.63,-0.379]],"front":[[-0.779,-1.208],[-0.764,-1.306],[-0.643,-1.464],[-0.651,-1.539],[-0.726,-1.622],[-0.726,-1.712],[-0.67,-1.731],[-0.636,-1.787],[-0.643,-1.885],[-0.726,-1.991],[-0.719,-2.051],[-0.643,-2.126],[-0.636,-2.871],[-0.704,-3.037],[-0.689,-3.759],[-0.346,-3.846],[-0.335,-4.008],[-0.248,-4.079],[0.294,-4.064],[0.365,-4],[0.376,-3.853],[0.692,-3.785],[0.734,-3.752],[0.756,-3.007],[0.651,-2.736],[0.643,-2.472],[0.722,-2.446],[0.764,-2.367],[0.756,-1.246],[0.779,-1.065],[0.764,-0.967],[0.711,-0.892],[0.726,-0.636],[0.674,-0.433],[0.546,-0.23],[0.301,0],[0,-0.008],[-0.331,-0.008],[-0.636,-0.335],[-0.741,-0.636],[-0.741,-0.824],[-0.704,-0.967]],"bottom":[[0,0.28],[0,0],[0,-0.298],[0.047,-0.587],[0.089,-0.648],[0.191,-0.675],[0.48,-0.675],[0.629,-0.648],[0.871,-0.536],[1.011,-0.517],[1.141,-0.433],[3.992,-0.461],[3.997,0.41],[1.132,0.424],[1.002,0.508],[0.862,0.526],[0.629,0.638],[0.219,0.675],[0.098,0.648],[0.056,0.587]]},"features":{"side":{"guard_window":[[[1.492,-1.934],[1.493,-1.379],[1.553,-1.219],[1.641,-1.14],[1.759,-1.098],[3.096,-1.102],[3.214,-1.161],[3.285,-1.241],[3.335,-1.401],[3.334,-1.888],[3.249,-2.099],[3.144,-2.178],[2.319,-2.336],[1.748,-2.242],[1.567,-2.145]]]},"rear":{},"front":{},"bottom":{}},"placement":{"side":{"plane":"xy","offset":{}},"rear":{"plane":"zy","offset":{"y":"tower_top_above_pin"}},"front":{"plane":"zy","offset":{"y":"tower_top_above_pin"}},"bottom":{"plane":"xz","offset":{"x":"rear_face_x"}}},"bounds":{"min":[-1.167,-2.512,-0.708],"max":[6.552,1.554,0.6885]},"volume_in3":6.7682,"centroid":[2.3488,-0.8647,0.0081],"shell":[2.8232,-0.7392,-0.0021],"area_in2":81.7292,"triangles":15646,"manifold":true,"interior":{"pocket":{"x":[0.24,3.11],"z":0.345,"floor_y":-1.0005},"rear_lug_slot":{"x":[-0.402,0.458],"z":0.25,"floor_y":-0.3815},"safety_detent_boss":{"x":[0.6,1.03],"face_z":0.185,"top_y":-0.2065},"trigger_slot":{"x":[1.768,2.448],"z":0.156},"magazine_well":{"x":[3.472,6.025],"z":0.449}},"holes":{"takedown":{"x":0,"y":0,"d":0.251},"pivot":{"x":6.375,"y":0,"d":0.251},"selector":{"x":0.803,"y":-0.466,"d":0.376},"hammer":{"x":2.771,"y":-0.375,"d":0.1568},"trigger":{"x":1.928,"y":-0.689,"d":0.1568}},"catches":{"button_pocket":{"x":3.291,"y":-0.565,"floor_z":-0.068,"face_z":0.664},"catch_slot":{"x":[3.048,4.557],"floor_z":-0.3799},"bolt_catch_slot":{"x":[3.203,3.375],"bottom_y":-0.38,"floor_z":-0.4409},"block":{"face_z":0.664,"x":[3.09,3.64],"front_ramp":0.16,"wall_z":0.56,"bottom_y":-1.03}},"rear_walls":{"r":0.75,"centre":[0.122,0.9985],"x":[-0.621,0.122],"meets_face_y":0.8963,"runs_out":[0.055,0.2515],"toe_x":[-0.1255,0.055]},"deck":{"y":0.2485,"x":[-0.02,6.194]},"slabs":[[-1.167,-0.546,-0.682,-0.781,1.554,0.682],[-0.781,-0.84,-0.682,-0.395,1.554,0.682],[-0.395,-1.409,-0.574,-0.009,0.455,0.582],[-0.009,-1.632,-0.446,0.377,0.26,0.441],[0.377,-1.855,-0.44,0.763,0.249,0.44],[0.763,-2.061,-0.44,1.149,0.249,0.44],[1.149,-2.387,-0.44,1.535,0.249,0.44],[1.535,-2.453,-0.44,1.921,0.249,0.44],[1.921,-2.512,-0.44,2.692,0.249,0.44],[2.692,-2.44,-0.708,3.078,0.249,0.649],[3.078,-2.374,-0.708,3.464,0.249,0.689],[3.464,-2.308,-0.708,3.85,0.249,0.689],[3.85,-2.242,-0.666,4.236,0.249,0.689],[4.236,-2.176,-0.666,4.622,0.249,0.689],[4.622,-2.11,-0.641,5.008,0.249,0.689],[5.008,-2.044,-0.641,5.394,0.249,0.689],[5.394,-1.978,-0.641,5.78,0.249,0.689],[5.78,-1.913,-0.641,6.166,0.249,0.689],[6.166,-0.448,-0.542,6.552,0.249,0.56]],"slots":["receiver"]},"aero-m4e1-lower.selector":{"part":"aero-m4e1-lower","component":"selector","model":"aero-m4e1-lower.selector.glb","script":"brought_selectors.py","inputs":{"cmmg-safety-selector.hub_d":0.48,"cmmg-safety-selector.hub_t":0.05,"cmmg-safety-selector.lever_reach":0.81,"cmmg-safety-selector.lever_standoff":0.25,"cmmg-safety-selector.paddle_base_t":0.125,"cmmg-safety-selector.paddle_relief":0.015,"cmmg-safety-selector.paddle_relief_start":0.281,"cmmg-safety-selector.paddle_start":0.09,"cmmg-safety-selector.paddle_width":0.25,"cmmg-safety-selector.pointer_angle":60,"cmmg-safety-selector.pointer_fillet_r":0.09,"cmmg-safety-selector.pointer_reach":0.34,"cmmg-safety-selector.shaft_d":0.37225,"cmmg-safety-selector.shaft_end_chamfer":0.024,"cmmg-safety-selector.shaft_length":0.9375,"cmmg-safety-selector.step_1_height":0.17,"cmmg-safety-selector.step_1_inset":0.009,"cmmg-safety-selector.step_2_height":0.2,"cmmg-safety-selector.step_2_inset":0.025,"cmmg-safety-selector.step_3_height":0.22,"cmmg-safety-selector.step_3_inset":0.043,"cmmg-safety-selector.step_4_height":0.24,"cmmg-safety-selector.step_4_inset":0.075,"cmmg-safety-selector.step_5_inset":0.11,"std.ar15.lower_body_width":0.88,"std.ar15.selector_hole_d":0.376,"std.ar15.selector_x":0.803,"std.ar15.selector_y":-0.466},"profiles":{},"bounds":{"min":[-0.007,-0.7058,-0.69],"max":[1.143,-0.2262,0.4975]},"volume_in3":0.1423,"centroid":[0.703,-0.466,-0.1335],"shell":[0.665,-0.466,-0.2048],"area_in2":2.158,"triangles":6464,"manifold":true,"slabs":[[-0.007,-0.706,-0.69,1.143,-0.226,-0.294],[0.617,-0.652,-0.294,0.989,-0.28,0.498]],"slots":["controls"]},"aero-m4e1-lower.stock":{"part":"aero-m4e1-lower","component":"stock","model":"aero-m4e1-lower.stock.glb","script":"aero_m4e1_lower.py","inputs":{"aero-m4e1-lower.sling_loop_depth":0.688,"aero-m4e1-lower.sling_loop_width":1.785,"aero-m4e1-lower.sling_loop_wire_d":0.16,"aero-m4e1-lower.stock_butt_flare":0.535,"aero-m4e1-lower.stock_butt_full":0.234,"aero-m4e1-lower.stock_butt_width":1.707,"aero-m4e1-lower.stock_lever_width":0.757,"aero-m4e1-lower.stock_lock_pin_d":0.417,"aero-m4e1-lower.stock_slot_columns":5,"aero-m4e1-lower.stock_slot_depth_lower":0.25,"aero-m4e1-lower.stock_slot_depth_upper":0.13,"aero-m4e1-lower.stock_slot_height":0.155,"aero-m4e1-lower.stock_slot_length":1.03,"aero-m4e1-lower.stock_slot_pitch":1.14,"aero-m4e1-lower.stock_slot_rear_x":-8.03,"aero-m4e1-lower.stock_slot_row1_y":0.47,"aero-m4e1-lower.stock_slot_row2_y":0.07,"aero-m4e1-lower.stock_slot_rows_x":-7.6,"aero-m4e1-lower.stock_slot_slope":-0.92,"aero-m4e1-lower.stock_top_above_pin":1.787,"aero-m4e1-lower.stock_width":1.443},"profiles":{"complete":[[-8.594,1.033],[-8.546,0.733],[-8.548,0.401],[-8.515,0.302],[-8.532,0.186],[-8.484,-0.114],[-8.501,-0.213],[-8.468,-0.263],[-8.485,-0.363],[-8.453,-0.462],[-8.454,-0.794],[-8.421,-0.828],[-8.439,-0.994],[-8.39,-1.226],[-8.408,-1.425],[-8.375,-1.459],[-8.376,-1.774],[-8.343,-1.808],[-8.345,-2.123],[-8.312,-2.156],[-8.329,-2.256],[-8.28,-2.422],[-8.297,-2.472],[-8.233,-2.837],[-8.249,-2.887],[-8.216,-2.921],[-8.185,-3.253],[-8.077,-3.345],[-7.828,-3.346],[-7.787,-3.305],[-7.619,-3.057],[-7.669,-2.99],[-7.667,-2.641],[-7.36,-2.585],[-7.293,-2.602],[-6.549,-1.601],[-6.408,-1.461],[-5.809,-1.248],[-4.759,-0.573],[-3.365,-0.564],[-3.142,-0.789],[-3.102,-1.129],[-3.077,-1.022],[-3.027,-0.989],[-2.925,-0.641],[-2.683,-0.368],[-2.384,-0.237],[-1.72,-0.24],[-1.677,-0.083],[-1.684,0.291],[-1.625,0.282],[-1.601,0.174],[-1.253,0.173],[-1.248,-0.5],[-1.223,-0.525],[-1.123,-0.509],[-0.858,-0.543],[-0.609,-0.644],[-0.37,-0.886],[-0.28,-1.094],[-0.139,-1.103],[-0.296,-1.111],[-0.338,-1.152],[-0.323,-1.418],[-0.407,-1.7],[-2.181,-4.347],[-2.198,-4.446],[-1.974,-4.539],[-0.681,-4.861],[-0.349,-4.929],[-0.183,-4.93],[-0.008,-4.773],[-0.008,-4.707],[-0.123,-4.556],[-0.123,-4.44],[0.414,-3.414],[0.556,-3.29],[0.805,-3.308],[0.846,-3.267],[0.847,-3.2],[0.715,-3.05],[0.699,-2.901],[1.009,-2.329],[1.142,-2.314],[1.158,-2.347],[1.307,-2.381],[2.187,-2.535],[2.353,-2.536],[6.174,-1.875],[6.183,-1.767],[6.085,-1.518],[6.089,-0.671],[6.207,-0.422],[6.315,-0.315],[6.523,-0.192],[6.574,-0.092],[6.574,-0.009],[6.541,0.074],[6.401,0.182],[3.595,0.214],[3.562,0.28],[3.48,0.297],[3.372,0.373],[3.356,0.572],[3.249,0.664],[3.116,0.648],[3.024,0.54],[3.023,0.325],[3.081,0.216],[2.334,0.22],[2.342,0.278],[2.301,0.32],[1.689,0.688],[1.589,0.689],[1.481,0.598],[1.255,0.226],[-0.073,0.249],[-0.371,0.417],[-0.577,0.709],[-0.576,0.974],[-0.626,0.991],[-0.625,1.107],[-0.608,1.257],[-0.575,1.256],[-0.559,1.024],[-0.541,1.256],[-0.566,1.314],[-0.624,1.323],[-0.631,1.547],[-1.046,1.549],[-1.229,1.501],[-1.262,1.534],[-1.561,1.535],[-1.619,1.494],[-1.645,1.403],[-1.71,1.503],[-2.076,1.522],[-8.019,1.602],[-8.118,1.619],[-8.25,1.77],[-8.466,1.787],[-8.558,1.696],[-8.591,1.58]],"stock_end":[[-0.858,-1.778],[-0.858,-2.135],[-0.844,-2.162],[-0.858,-2.186],[-0.844,-2.199],[-0.82,-2.788],[-0.807,-2.802],[-0.742,-3.381],[-0.728,-3.395],[-0.723,-3.497],[-0.709,-3.511],[-0.649,-3.896],[-0.515,-4.392],[-0.54,-4.417],[-0.61,-4.417],[-0.612,-4.429],[-0.521,-4.431],[-0.496,-4.457],[-0.468,-4.559],[-0.494,-4.584],[-0.61,-4.584],[-0.612,-4.624],[-0.47,-4.621],[-0.436,-4.656],[-0.408,-4.73],[-0.433,-4.774],[-0.596,-4.774],[-0.61,-4.76],[-0.612,-4.772],[-0.41,-4.779],[-0.38,-4.809],[-0.38,-4.837],[-0.348,-4.888],[-0.373,-4.927],[-0.582,-4.927],[-0.612,-4.962],[-0.331,-4.964],[-0.202,-5.099],[-0.123,-5.136],[0.039,-5.154],[0.053,-5.141],[0.155,-5.136],[0.234,-5.099],[0.364,-4.964],[0.612,-4.962],[0.61,-4.913],[0.572,-4.951],[0.545,-4.951],[0.521,-4.927],[0.406,-4.927],[0.38,-4.897],[0.413,-4.814],[0.447,-4.774],[0.612,-4.772],[0.61,-4.76],[0.466,-4.76],[0.44,-4.721],[0.498,-4.621],[0.612,-4.619],[0.521,-4.584],[0.496,-4.545],[0.528,-4.448],[0.559,-4.417],[0.612,-4.415],[0.547,-4.378],[0.552,-4.346],[0.644,-4.026],[0.705,-3.66],[0.718,-3.646],[0.723,-3.548],[0.737,-3.534],[0.742,-3.419],[0.765,-3.358],[0.783,-3.108],[0.802,-3.062],[0.802,-2.974],[0.816,-2.96],[0.839,-2.45],[0.853,-2.436],[0.858,-1.805],[0.853,-1.68],[0.839,-1.666],[0.834,-1.37],[0.82,-1.356],[0.816,-1.18],[0.802,-1.166],[0.765,-0.818],[0.742,-0.753],[0.718,-0.559],[0.644,-0.387],[0.644,-0.067],[0.6,-0.079],[0.406,-0.074],[0.392,-0.088],[0.336,-0.074],[0.313,-0.097],[0.192,-0.07],[0.162,-0.039],[0.176,-0.021],[0.169,0],[0.002,0],[-0.058,0],[-0.056,-0.035],[-0.086,-0.065],[-0.262,-0.074],[-0.392,-0.13],[-0.484,-0.19],[-0.591,-0.297],[-0.626,-0.243],[-0.617,-0.1],[-0.654,-0.067],[-0.654,-0.392],[-0.723,-0.535],[-0.779,-0.874],[-0.797,-1.092],[-0.82,-1.161],[-0.844,-1.764]]},"features":{"complete":{"grip":[[[-2.256,-1.208],[1.064,-1.226],[1.044,-5.094],[-2.276,-5.077]]],"stock":[[[-8.715,1.847],[-1.576,1.809],[-1.603,-3.42],[-8.742,-3.383]]],"tube":[[[-1.693,1.611],[-0.631,1.605],[-0.639,0.111],[-1.701,0.117]]],"guard_window":[[[1.5,-2.042],[1.504,-1.361],[1.537,-1.278],[1.696,-1.138],[1.829,-1.122],[1.853,-1.147],[1.769,-1.445],[1.784,-1.694],[1.932,-2.011],[2.072,-2.152],[2.105,-2.153],[2.131,-2.095],[2.015,-1.911],[1.967,-1.629],[2.018,-1.43],[2.177,-1.207],[2.293,-1.124],[3.024,-1.111],[3.206,-1.195],[3.297,-1.304],[3.313,-1.37],[3.31,-1.985],[3.259,-2.117],[3.184,-2.191],[3.018,-2.257],[2.353,-2.37],[2.154,-2.369],[1.723,-2.283],[1.549,-2.158]]],"stock_lever":[[[-5.842,-1.273],[-4.726,-0.565],[-3.365,-0.572],[-3.15,-0.789],[-3.119,-1.121],[-3.816,-1.134],[-4.231,-1.132],[-4.497,-1.147],[-5.663,-1.921],[-5.845,-1.854]]],"stock_lock_pin":[[[-4.231,-1.132],[-3.816,-1.134],[-3.818,-1.516],[-4.233,-1.514]]],"sling_loop":[[[-7.659,-2.641],[-7.31,-2.593],[-6.832,-3.26],[-6.916,-3.475],[-7.198,-3.474],[-7.661,-2.99]]]},"stock_end":{}},"placement":{"complete":{"plane":"xy","offset":{}},"stock_end":{"plane":"zy","offset":{"y":"stock_top_above_pin"}}},"bounds":{"min":[-8.594,-3.346,-0.8925],"max":[-1.576,1.787,0.8925]},"volume_in3":28.0812,"centroid":[-5.6197,-0.0121,0.001],"shell":[-5.5281,-0.1935,-0.0041],"area_in2":90.5626,"triangles":17636,"manifold":true,"slabs":[[-8.594,-3.048,-0.854,-8.204,1.787,0.854],[-8.204,-3.346,-0.785,-7.814,1.718,0.785],[-7.814,-3.332,-0.856,-7.424,1.599,0.856],[-7.424,-3.241,-0.892,-7.034,1.594,0.892],[-7.034,-2.254,-0.721,-6.645,1.589,0.721],[-6.645,-1.73,-0.721,-6.255,1.583,0.721],[-6.255,-1.406,-0.721,-5.865,1.578,0.721],[-5.865,-1.921,-0.721,-5.475,1.573,0.721],[-5.475,-1.796,-0.721,-5.085,1.568,0.721],[-5.085,-1.537,-0.721,-4.695,1.563,0.721],[-4.695,-1.279,-0.721,-4.305,1.557,0.721],[-4.305,-1.516,-0.721,-3.525,1.552,0.721],[-3.525,-1.129,-0.721,-2.746,1.542,0.721],[-2.746,-0.439,-0.721,-2.356,1.531,0.721],[-2.356,-0.24,-0.721,-1.576,1.526,0.721]],"slots":["stock"]},"aero-m4e1-stripped-lower":{"part":"aero-m4e1-stripped-lower","model":"aero-m4e1-stripped-lower.glb","script":"aero_m4e1_stripped_lower.py","inputs":{"aero-m4e1-stripped-lower.bolt_catch_boss_bottom_y":-0.02,"aero-m4e1-stripped-lower.bolt_catch_boss_front_x":3.52,"aero-m4e1-stripped-lower.bolt_catch_boss_out":0.708,"aero-m4e1-stripped-lower.bolt_catch_boss_rear_x":3.01,"aero-m4e1-stripped-lower.buffer_axis_above_pin":0.8775,"aero-m4e1-stripped-lower.catch_block_front_ramp":0.16,"aero-m4e1-stripped-lower.catch_block_front_x":3.64,"aero-m4e1-stripped-lower.catch_pad_bottom_y":-0.78,"aero-m4e1-stripped-lower.catch_pad_front_x":4.56,"aero-m4e1-stripped-lower.catch_pad_out":0.666,"aero-m4e1-stripped-lower.catch_pad_rear_x":3.048,"aero-m4e1-stripped-lower.catch_pad_top_y":-0.3,"aero-m4e1-stripped-lower.ear_left_out":0.542,"aero-m4e1-stripped-lower.ear_left_ramp":0.06,"aero-m4e1-stripped-lower.ear_left_rear_x":6.15,"aero-m4e1-stripped-lower.ear_right_out":0.519,"aero-m4e1-stripped-lower.ear_right_rear_x":6.18,"aero-m4e1-stripped-lower.front_view_lug_slot":0.549,"aero-m4e1-stripped-lower.grip_lug_face_angle":60,"aero-m4e1-stripped-lower.grip_lug_flat_y":-1.9995,"aero-m4e1-stripped-lower.grip_lug_rear_x":-0.075,"aero-m4e1-stripped-lower.grip_mating_y":-1.063,"aero-m4e1-stripped-lower.grip_seat_y":-1.0695,"aero-m4e1-stripped-lower.guard_root_rear_x":1.175,"aero-m4e1-stripped-lower.guard_slot1_front_x":2.279,"aero-m4e1-stripped-lower.guard_slot1_rear_x":1.655,"aero-m4e1-stripped-lower.guard_slot2_front_x":3.258,"aero-m4e1-stripped-lower.guard_slot2_rear_x":2.433,"aero-m4e1-stripped-lower.guard_slot_width":0.335,"aero-m4e1-stripped-lower.guard_width":0.59,"aero-m4e1-stripped-lower.panel_left_out":0.603,"aero-m4e1-stripped-lower.panel_left_ramp":0.08,"aero-m4e1-stripped-lower.panel_left_rear_x":3.03,"aero-m4e1-stripped-lower.panel_right_bottom_y":-1.03,"aero-m4e1-stripped-lower.panel_right_out":0.664,"aero-m4e1-stripped-lower.panel_right_ramp":0.17,"aero-m4e1-stripped-lower.panel_right_rear_x":3.09,"aero-m4e1-stripped-lower.rear_end_x":-1.125,"aero-m4e1-stripped-lower.rear_face_x":-1.14,"aero-m4e1-stripped-lower.rear_underside_arc_r":0.75,"aero-m4e1-stripped-lower.tower_top_above_pin":1.554,"aero-m4e1-stripped-lower.wall_right_below_panel":0.56,"std.ar15.bolt_catch_plunger_hole_d":0.156,"std.ar15.bolt_catch_plunger_hole_depth":0.4703,"std.ar15.bolt_catch_plunger_hole_y":-0.195,"std.ar15.bolt_catch_slot_bottom_y":-0.38,"std.ar15.bolt_catch_slot_floor":0.4409,"std.ar15.bolt_catch_slot_front_x":3.375,"std.ar15.bolt_catch_slot_width":0.172,"std.ar15.bore_axis_y":0.8775,"std.ar15.buffer_tower_front_x":-0.628,"std.ar15.deck_front_x":6.194,"std.ar15.deck_y":0.2485,"std.ar15.fcg_pin_hole_d":0.15675,"std.ar15.fcg_pocket_corner_r":0.218,"std.ar15.fcg_pocket_depth":1.249,"std.ar15.fcg_pocket_front_x":3.11,"std.ar15.fcg_pocket_length":2.87,"std.ar15.fcg_pocket_width":0.69,"std.ar15.front_lug_slot_width":0.5,"std.ar15.grip_lug_face_angle":60,"std.ar15.grip_lug_face_from_pin":1.228,"std.ar15.grip_lug_width":0.375,"std.ar15.grip_seat_below_deck":1.318,"std.ar15.hammer_pin_x":2.771,"std.ar15.hammer_pin_y":-0.375,"std.ar15.lower_body_width":0.88,"std.ar15.mag_catch_cbore_d":0.312,"std.ar15.mag_catch_cbore_depth":0.25,"std.ar15.mag_catch_fence_out":0.549,"std.ar15.mag_catch_hole_d":0.2055,"std.ar15.mag_catch_slot_bottom_y":-0.689,"std.ar15.mag_catch_slot_floor":0.3799,"std.ar15.mag_catch_slot_front_x":4.557,"std.ar15.mag_catch_slot_h":0.252,"std.ar15.mag_catch_slot_rear_x":3.048,"std.ar15.mag_catch_x":3.291,"std.ar15.mag_catch_y":-0.565,"std.ar15.mag_release_pocket_depth":0.617,"std.ar15.mag_release_pocket_h":0.515,"std.ar15.mag_release_pocket_w":0.319,"std.ar15.magwell_box_length":2.398,"std.ar15.magwell_corner_r":0.062,"std.ar15.magwell_front_inner_x":6.025,"std.ar15.magwell_length":2.553,"std.ar15.magwell_spine_slot_width":0.47,"std.ar15.magwell_width":0.898,"std.ar15.pin_spacing":6.375,"std.ar15.pivot_hole_d":0.251,"std.ar15.rear_lug_slot_depth":0.63,"std.ar15.rear_lug_slot_rear_x":-0.402,"std.ar15.rear_lug_slot_width":0.5,"std.ar15.rear_underside_arc_center_below_seat":0.1928,"std.ar15.rear_underside_arc_center_x":-1.0238,"std.ar15.rear_underside_arc_r_fullest":0.716,"std.ar15.rear_underside_round_r":0.44,"std.ar15.rear_wall_arc_r":0.75,"std.ar15.receiver_rear_x":-1.125,"std.ar15.safety_detent_boss_below_deck":0.455,"std.ar15.safety_detent_boss_face":0.53,"std.ar15.safety_detent_boss_from_rear":0.36,"std.ar15.safety_detent_boss_length":0.43,"std.ar15.selector_hole_d":0.376,"std.ar15.selector_x":0.803,"std.ar15.selector_y":-0.466,"std.ar15.takedown_hole_d":0.251,"std.ar15.trigger_pin_x":1.928,"std.ar15.trigger_pin_y":-0.689,"std.ar15.trigger_slot_front_ahead_of_pin":0.52,"std.ar15.trigger_slot_length":0.68,"std.ar15.trigger_slot_width":0.312,"std.ar15.upper_rear_face_x":-0.621,"std.receiver_extension.milspec_od":1.148},"profiles":{"side":[[-1.167,0.722],[-1.145,-0.296],[-1.116,-0.502],[-0.821,-0.528],[-0.611,-0.621],[-0.414,-0.802],[-0.285,-1.059],[-0.112,-1.08],[-0.129,-1.24],[-0.079,-1.291],[-0.075,-1.371],[0.991,-1.987],[1.143,-1.979],[1.167,-2.324],[2.268,-2.512],[6.147,-1.85],[6.16,-1.753],[6.06,-1.458],[6.079,-0.609],[6.197,-0.391],[6.509,-0.148],[6.552,0.004],[6.501,0.13],[6.413,0.202],[5.926,0.245],[0.072,0.244],[-0.062,0.269],[-0.306,0.388],[-0.52,0.662],[-0.586,0.889],[-0.61,1.545],[-0.984,1.567],[-1.14,1.521]],"rear":[[-0.682,-0.566],[-0.682,-0.754],[-0.42,-1.593],[-0.484,-1.672],[-0.574,-1.702],[-0.615,-1.751],[-0.607,-1.856],[-0.555,-1.923],[-0.532,-2.088],[-0.487,-2.156],[-0.547,-2.246],[-0.555,-2.336],[-0.472,-2.448],[-0.487,-2.531],[-0.555,-2.568],[-0.547,-2.621],[-0.487,-2.681],[-0.487,-3.625],[-0.54,-3.94],[-0.289,-3.982],[-0.206,-4.079],[0.266,-4.079],[0.349,-3.989],[0.645,-3.94],[0.645,-3.625],[0.555,-3.4],[0.555,-2.981],[0.562,-2.891],[0.667,-2.808],[0.667,-1.818],[0.562,-1.646],[0.454,-1.62],[0.435,-1.586],[0.66,-0.851],[0.682,-0.664],[0.63,-0.394],[0.424,-0.12],[0.289,0],[-0.004,0],[-0.296,0],[-0.487,-0.176],[-0.63,-0.379]],"front":[[-0.779,-1.208],[-0.764,-1.306],[-0.643,-1.464],[-0.651,-1.539],[-0.726,-1.622],[-0.726,-1.712],[-0.67,-1.731],[-0.636,-1.787],[-0.643,-1.885],[-0.726,-1.991],[-0.719,-2.051],[-0.643,-2.126],[-0.636,-2.871],[-0.704,-3.037],[-0.689,-3.759],[-0.346,-3.846],[-0.335,-4.008],[-0.248,-4.079],[0.294,-4.064],[0.365,-4],[0.376,-3.853],[0.692,-3.785],[0.734,-3.752],[0.756,-3.007],[0.651,-2.736],[0.643,-2.472],[0.722,-2.446],[0.764,-2.367],[0.756,-1.246],[0.779,-1.065],[0.764,-0.967],[0.711,-0.892],[0.726,-0.636],[0.674,-0.433],[0.546,-0.23],[0.301,0],[0,-0.008],[-0.331,-0.008],[-0.636,-0.335],[-0.741,-0.636],[-0.741,-0.824],[-0.704,-0.967]],"bottom":[[0,0.28],[0,0],[0,-0.298],[0.047,-0.587],[0.089,-0.648],[0.191,-0.675],[0.48,-0.675],[0.629,-0.648],[0.871,-0.536],[1.011,-0.517],[1.141,-0.433],[3.992,-0.461],[3.997,0.41],[1.132,0.424],[1.002,0.508],[0.862,0.526],[0.629,0.638],[0.219,0.675],[0.098,0.648],[0.056,0.587]]},"features":{"side":{"guard_window":[[[1.492,-1.934],[1.493,-1.379],[1.553,-1.219],[1.641,-1.14],[1.759,-1.098],[3.096,-1.102],[3.214,-1.161],[3.285,-1.241],[3.335,-1.401],[3.334,-1.888],[3.249,-2.099],[3.144,-2.178],[2.319,-2.336],[1.748,-2.242],[1.567,-2.145]]]},"rear":{},"front":{},"bottom":{}},"placement":{"side":{"plane":"xy","offset":{}},"rear":{"plane":"zy","offset":{"y":"tower_top_above_pin"}},"front":{"plane":"zy","offset":{"y":"tower_top_above_pin"}},"bottom":{"plane":"xz","offset":{"x":"rear_face_x"}}},"bounds":{"min":[-1.125,-2.512,-0.708],"max":[6.552,1.554,0.6885]},"volume_in3":5.8785,"centroid":[2.5566,-0.7717,0.009],"shell":[2.8762,-0.7087,-0.0022],"area_in2":79.4537,"triangles":16838,"manifold":true,"interior":{"pocket":{"x":[0.24,3.11],"z":0.345,"floor_y":-1.0005},"rear_lug_slot":{"x":[-0.402,0.458],"z":0.25,"floor_y":-0.3815},"safety_detent_boss":{"x":[0.6,1.03],"face_z":0.185,"top_y":-0.2065},"trigger_slot":{"x":[1.768,2.448],"z":0.156},"magazine_well":{"x":[3.472,6.025],"z":0.449}},"holes":{"takedown":{"x":0,"y":0,"d":0.251},"pivot":{"x":6.375,"y":0,"d":0.251},"selector":{"x":0.803,"y":-0.466,"d":0.376},"hammer":{"x":2.771,"y":-0.375,"d":0.1568},"trigger":{"x":1.928,"y":-0.689,"d":0.1568}},"catches":{"button_pocket":{"x":3.291,"y":-0.565,"floor_z":-0.068,"face_z":0.664},"catch_slot":{"x":[3.048,4.557],"floor_z":-0.3799},"bolt_catch_slot":{"x":[3.203,3.375],"bottom_y":-0.38,"floor_z":-0.4409},"block":{"face_z":0.664,"x":[3.09,3.64],"front_ramp":0.16,"wall_z":0.56,"bottom_y":-1.03}},"grip_mount":{"lug":{"seat_y":-1.0695,"x":[-0.075,1.175],"width":0.375,"foot_x":1.0072,"flat_y":-1.9995},"guard":{"width":0.59,"x":[1.175,3.335],"slot_width":0.335,"slot1_x":[1.655,2.279],"slot2_x":[2.433,3.258]},"rear_underside":{"round_r":0.44,"x":[-1.116,-0.285],"from_arc_centre":[0.7618,0.7663]}},"rear_walls":{"r":0.75,"centre":[0.122,0.9985],"x":[-0.621,0.122],"meets_face_y":0.8963,"runs_out":[0.055,0.2515],"toe_x":[-0.1255,0.055]},"deck":{"y":0.2485,"x":[-0.02,6.194]},"slabs":[[-1.125,-0.562,-0.682,-0.741,1.554,0.682],[-0.741,-0.913,-0.682,-0.357,1.553,0.682],[-0.357,-1.433,-0.564,0.027,0.422,0.564],[0.027,-1.655,-0.44,0.41,0.255,0.44],[0.41,-1.877,-0.44,0.794,0.249,0.44],[0.794,-2.326,-0.44,1.178,0.249,0.44],[1.178,-2.391,-0.44,1.562,0.249,0.44],[1.562,-2.457,-0.44,1.946,0.249,0.44],[1.946,-2.512,-0.44,2.714,0.249,0.44],[2.714,-2.436,-0.708,3.097,0.249,0.664],[3.097,-2.37,-0.708,3.481,0.249,0.689],[3.481,-2.305,-0.708,3.865,0.249,0.689],[3.865,-2.239,-0.666,4.249,0.249,0.689],[4.249,-2.174,-0.666,4.633,0.249,0.689],[4.633,-2.108,-0.641,5.017,0.249,0.689],[5.017,-2.043,-0.641,5.4,0.249,0.689],[5.4,-1.977,-0.641,5.784,0.249,0.689],[5.784,-1.912,-0.641,6.168,0.249,0.689],[6.168,-0.444,-0.542,6.552,0.249,0.56]],"slots":["receiver"]},"aero-m4e1-threaded-upper.receiver":{"part":"aero-m4e1-threaded-upper","component":"receiver","model":"aero-m4e1-threaded-upper.receiver.glb","script":"aero_m4e1_threaded_upper.py","inputs":{"aero-m4e1-threaded-upper.body_radius":0.59,"aero-m4e1-threaded-upper.bore_axis_above_pin":0.8775,"aero-m4e1-threaded-upper.bore_d":1,"aero-m4e1-threaded-upper.cam_boss_bottom_y":1.21,"aero-m4e1-threaded-upper.cam_boss_ear_half_width":0.373,"aero-m4e1-threaded-upper.cam_boss_face_half_width":0.172,"aero-m4e1-threaded-upper.cam_boss_face_top_y":1.519,"aero-m4e1-threaded-upper.cam_boss_flank_run":0.135,"aero-m4e1-threaded-upper.cam_boss_top_half_width":0.245,"aero-m4e1-threaded-upper.cam_boss_top_y":1.648,"aero-m4e1-threaded-upper.cam_boss_x":5.14,"aero-m4e1-threaded-upper.deflector_out":1.47,"aero-m4e1-threaded-upper.deflector_point_x":2.72,"aero-m4e1-threaded-upper.deflector_point_y":1.16,"aero-m4e1-threaded-upper.dovetail_foot_half_width":0.323,"aero-m4e1-threaded-upper.dovetail_foot_y":1.885,"aero-m4e1-threaded-upper.fa_axis_angle":20,"aero-m4e1-threaded-upper.fa_bore_d":0.509,"aero-m4e1-threaded-upper.fa_bore_depth":0.65,"aero-m4e1-threaded-upper.fa_housing_front_x":1.9,"aero-m4e1-threaded-upper.fa_housing_out_rear":1.67,"aero-m4e1-threaded-upper.fa_housing_outer_bottom_y":0.92,"aero-m4e1-threaded-upper.fa_housing_outer_top_y":1.2,"aero-m4e1-threaded-upper.fa_housing_r":0.3125,"aero-m4e1-threaded-upper.fa_inner_bore_d":0.315,"aero-m4e1-threaded-upper.fa_rear_x":-0.395,"aero-m4e1-threaded-upper.fa_rear_z":1.09,"aero-m4e1-threaded-upper.front_face_x":7.036,"aero-m4e1-threaded-upper.handle_seat_x":0.092,"aero-m4e1-threaded-upper.left_pad_front_x":6.202,"aero-m4e1-threaded-upper.left_pad_rear_x":3.077,"aero-m4e1-threaded-upper.left_pad_step_front_x":4.585,"aero-m4e1-threaded-upper.left_pad_step_rear_x":4.05,"aero-m4e1-threaded-upper.left_pad_step_top_y":0.743,"aero-m4e1-threaded-upper.left_pad_top_y":0.662,"aero-m4e1-threaded-upper.lug_wall_half_width":0.453,"aero-m4e1-threaded-upper.port_bottom_y":0.841,"aero-m4e1-threaded-upper.port_end_r":0.25,"aero-m4e1-threaded-upper.port_front_x":6.036,"aero-m4e1-threaded-upper.port_length":3.125,"aero-m4e1-threaded-upper.rail_front_x":6.583,"aero-m4e1-threaded-upper.rail_neck_bottom_y":1.737,"aero-m4e1-threaded-upper.rail_neck_half_width":0.309,"aero-m4e1-threaded-upper.rail_tongue_rear_x":-0.562,"aero-m4e1-threaded-upper.rail_top_above_pin":2.09,"aero-m4e1-threaded-upper.receiver_rear_x":-0.621,"aero-m4e1-threaded-upper.shoulder_bottom_y":0.875,"aero-m4e1-threaded-upper.side_bottom_y":1.435,"aero-m4e1-threaded-upper.side_half_width":0.42,"aero-m4e1-threaded-upper.underside_y":0.2485,"std.ar15.bore_axis_y":0.8775,"std.ar15.buffer_tower_front_x":-0.628,"std.ar15.buffer_tower_od":1.392,"std.ar15.buffer_trough_r":0.5625,"std.ar15.charging_handle_channel_floor_y":1.5845,"std.ar15.charging_handle_channel_front_round_x":5.726,"std.ar15.charging_handle_channel_rear_half_width":0.209,"std.ar15.charging_handle_channel_rear_round_x":0.676,"std.ar15.charging_handle_channel_roof_y":1.9085,"std.ar15.charging_handle_channel_round_r":0.2665,"std.ar15.charging_handle_channel_slot_half_width":0.205,"std.ar15.charging_handle_channel_tier_half_width":0.25,"std.ar15.charging_handle_channel_tier_top_y":1.7115,"std.ar15.charging_handle_channel_top_half_width":0.22,"std.ar15.charging_handle_latch_slot_bottom_y":1.52,"std.ar15.charging_handle_latch_slot_floor":0.045,"std.ar15.charging_handle_latch_slot_length":0.195,"std.ar15.charging_handle_latch_slot_top_y":1.935,"std.ar15.charging_handle_latch_slot_wall":0.156,"std.ar15.charging_handle_notch_chamfer":0.083,"std.ar15.charging_handle_notch_floor_y":1.571,"std.ar15.charging_handle_notch_roof_y":1.89,"std.ar15.deck_y":0.2485,"std.ar15.front_lug_slot_width":0.5,"std.ar15.rail_tongue_end_r":0.4175,"std.ar15.rail_tongue_fillet_r":0.1476,"std.ar15.rail_tongue_front_x":0.277,"std.ar15.rail_tongue_half_width":0.318,"std.ar15.rail_tongue_shoulder_x":0.4165,"std.ar15.rear_lug_slot_rear_x":-0.402,"std.ar15.rear_lug_slot_width":0.5,"std.ar15.rear_wall_arc_r":0.75,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.top_width":0.835},"profiles":{"side":[[-0.649,0.903],[-0.607,0.743],[-0.498,0.55],[-0.368,0.419],[-0.221,0.331],[-0.214,-0.207],[-0.193,-0.22],[0.227,-0.221],[0.24,-0.208],[0.24,0.036],[0.224,0.061],[0.224,0.229],[0.338,0.25],[6.146,0.248],[6.159,0.227],[6.15,-0.009],[6.183,-0.101],[6.246,-0.173],[6.322,-0.215],[6.414,-0.215],[6.49,-0.182],[6.57,-0.094],[6.595,0.007],[6.587,0.243],[6.608,0.297],[6.684,0.297],[6.701,0.272],[6.718,0.297],[6.734,0.297],[6.751,0.272],[6.777,0.297],[6.818,0.272],[6.835,0.297],[6.852,0.297],[6.869,0.271],[6.886,0.297],[6.928,0.271],[6.945,0.297],[6.961,0.296],[6.978,0.271],[7.033,0.317],[7.059,0.561],[7.06,1.158],[7.035,1.427],[6.997,1.482],[6.98,1.465],[6.947,1.49],[6.922,1.465],[6.888,1.49],[6.863,1.465],[6.838,1.49],[6.812,1.465],[6.787,1.49],[6.77,1.465],[6.753,1.465],[6.728,1.491],[6.711,1.465],[6.669,1.482],[6.653,1.457],[6.611,1.457],[6.59,1.478],[6.599,2.067],[6.586,2.096],[6.393,2.088],[6.389,2.067],[6.414,2.067],[6.422,1.991],[6.376,1.97],[6.3,1.97],[6.216,1.971],[6.195,2],[6.196,2.084],[6.158,2.097],[6.006,2.089],[5.994,2.068],[6.019,2.068],[6.027,2.017],[6.015,1.979],[5.821,1.971],[5.8,1.992],[5.801,2.085],[5.754,2.098],[5.611,2.081],[5.632,2.01],[5.611,1.972],[5.418,1.972],[5.405,1.985],[5.405,2.086],[5.309,2.09],[5.212,2.078],[5.237,2.01],[5.216,1.972],[5.023,1.973],[5.01,1.985],[5.006,2.091],[4.897,2.091],[4.838,2.091],[4.825,2.078],[4.834,1.986],[4.821,1.973],[4.619,1.974],[4.611,2.091],[4.443,2.092],[4.43,2.079],[4.434,1.974],[4.224,1.974],[4.22,2.079],[4.208,2.092],[4.124,2.092],[4.056,2.092],[4.044,2.08],[4.039,1.975],[3.829,1.975],[3.817,2.004],[3.825,2.08],[3.813,2.093],[3.661,2.093],[3.649,2.08],[3.648,1.98],[3.619,1.967],[3.442,1.967],[3.422,2.005],[3.43,2.081],[3.417,2.093],[3.266,2.094],[3.254,2.081],[3.253,1.989],[3.224,1.968],[3.039,1.968],[3.026,1.981],[3.035,2.073],[3.022,2.094],[2.871,2.094],[2.858,2.082],[2.858,1.981],[2.837,1.968],[2.636,1.977],[2.64,2.074],[2.619,2.095],[2.476,2.095],[2.463,2.083],[2.463,1.982],[2.442,1.969],[2.249,1.97],[2.236,1.999],[2.245,2.075],[2.232,2.087],[2.073,2.088],[2.068,1.991],[2.047,1.97],[1.854,1.97],[1.841,1.983],[1.846,2.088],[1.677,2.088],[1.673,1.992],[1.652,1.971],[1.459,1.971],[1.446,1.984],[1.455,2.076],[1.442,2.089],[1.282,2.089],[1.278,2.001],[1.257,1.971],[1.064,1.972],[1.06,2.06],[1.076,2.068],[1.047,2.089],[-0.559,2.084],[-0.588,2.055],[-0.584,1.916],[-0.525,1.899],[0.013,1.898],[0.092,1.818],[0.092,1.667],[0.004,1.579],[-0.61,1.588],[-0.622,1.576],[-0.648,1.256]]},"features":{"side":{"forward_assist_housing":[[[-0.627,1.449],[1.777,1.445],[1.903,1.344],[1.902,0.84],[1.524,0.714],[0.01,0.524],[-0.494,0.508],[-0.628,0.659]]],"deflector":[[[1.878,1.361],[2.324,1.579],[2.559,1.662],[2.744,1.611],[2.954,1.46],[2.953,0.838],[2.533,0.838],[1.903,1.092]]]}},"placement":{"side":{"plane":"xy","offset":{}}},"bounds":{"min":[-0.621,-0.221,-0.59],"max":[7.036,2.09,1.5179]},"volume_in3":5.6473,"centroid":[2.8622,1.0332,0.1257],"shell":[3.0035,1.0898,0.0584],"area_in2":80.81,"triangles":13682,"manifold":true,"rear_corner":{"r":0.75,"centre":[0.122,0.9985],"x":[-0.628,-0.0116],"reach_z":0.696,"trough_r":0.5625},"slabs":[[-0.621,0.341,-0.59,-0.238,2.09,1.42],[-0.238,-0.221,-0.59,0.145,2.09,1.518],[0.145,-0.221,-0.59,0.528,2.09,1.391],[0.528,0.249,-0.59,0.91,1.972,1.252],[0.91,0.249,-0.59,1.293,1.972,1.113],[1.293,0.249,-0.59,1.676,1.972,0.973],[1.676,0.249,-0.59,2.059,1.972,0.892],[2.059,0.249,-0.59,2.442,1.972,1.227],[2.442,0.249,-0.59,2.825,1.972,1.47],[2.825,0.249,-0.59,3.207,1.972,0.978],[3.207,0.249,-0.59,5.887,1.972,0.59],[5.887,-0.215,-0.59,6.653,1.992,0.59],[6.653,0.271,-0.59,7.036,1.491,0.59]],"slots":["receiver"]},"aero-mid-gas-tube":{"part":"aero-mid-gas-tube","model":"aero-mid-gas-tube.glb","script":"aero_mid_gas_tube.py","inputs":{"aero-mid-gas-tube.bend_end_from_rear":5.56,"aero-mid-gas-tube.bend_offset":0.156,"aero-mid-gas-tube.bend_radius":4.2,"aero-mid-gas-tube.bend_start_from_rear":3.61,"aero-mid-gas-tube.bore":0.13,"aero-mid-gas-tube.crimp_depth":0.012,"aero-mid-gas-tube.crimp_front_from_front":0.088,"aero-mid-gas-tube.crimp_rear_from_front":0.293,"aero-mid-gas-tube.crimp_width":0.035,"aero-mid-gas-tube.end_break":0.012,"aero-mid-gas-tube.gas_hole_d":0.125,"aero-mid-gas-tube.gas_hole_from_front":0.605,"aero-mid-gas-tube.head_length":0.1,"aero-mid-gas-tube.length":11.75,"aero-mid-gas-tube.od":0.18,"aero-mid-gas-tube.pin_hole_d":0.078,"aero-mid-gas-tube.pin_hole_from_front":0.187,"aero-mid-gas-tube.plug_length":0.44,"aero-mid-gas-tube.relief_depth":0.008,"aero-mid-gas-tube.relief_end_from_rear":2.31},"profiles":{"side":[[0,0.078],[0.014,0.063],[0,0.049],[0.014,0.035],[0.014,0.007],[0.021,0],[6.425,0],[6.439,0.014],[6.608,0.014],[6.623,0.028],[6.707,0.028],[6.721,0.014],[6.75,0.042],[6.764,0.042],[6.792,0.014],[6.82,0.042],[6.848,0.042],[6.862,0.056],[6.877,0.042],[6.891,0.056],[6.989,0.056],[7.003,0.071],[7.088,0.071],[7.102,0.085],[7.243,0.085],[7.257,0.099],[7.37,0.099],[7.384,0.113],[7.483,0.113],[7.497,0.127],[7.61,0.127],[7.624,0.141],[7.737,0.141],[7.751,0.155],[8.329,0.155],[8.343,0.141],[8.358,0.141],[8.372,0.155],[8.4,0.155],[8.414,0.141],[8.442,0.141],[8.456,0.155],[8.809,0.155],[8.823,0.169],[8.95,0.169],[8.964,0.155],[9.345,0.155],[9.359,0.141],[9.387,0.169],[9.401,0.155],[9.416,0.155],[9.43,0.169],[9.458,0.169],[9.472,0.155],[9.5,0.155],[9.514,0.169],[9.528,0.169],[9.542,0.155],[9.684,0.155],[9.698,0.169],[11.63,0.169],[11.644,0.155],[11.687,0.155],[11.701,0.169],[11.736,0.176],[11.736,0.261],[11.75,0.275],[11.715,0.31],[7.864,0.31],[7.85,0.296],[7.695,0.296],[7.681,0.282],[7.554,0.282],[7.539,0.268],[7.427,0.268],[7.413,0.254],[7.3,0.254],[7.286,0.24],[7.159,0.24],[7.145,0.226],[7.06,0.226],[7.046,0.212],[6.933,0.212],[6.919,0.197],[6.792,0.197],[6.778,0.183],[6.665,0.183],[6.651,0.169],[6.524,0.169],[6.51,0.155],[4.507,0.155],[4.493,0.141],[4.394,0.141],[4.38,0.155],[3.378,0.155],[3.364,0.141],[3.308,0.141],[3.294,0.155],[3.265,0.155],[3.251,0.141],[2.927,0.141],[2.913,0.155],[2.786,0.155],[2.772,0.141],[2.179,0.141],[2.165,0.155],[2.151,0.155],[2.137,0.141],[1.728,0.141],[1.714,0.155],[1.7,0.155],[1.686,0.141],[0.783,0.141],[0.769,0.155],[0.642,0.155],[0.628,0.141],[0.416,0.141],[0.402,0.155],[0.36,0.155],[0.346,0.141],[0.303,0.141],[0.289,0.155],[0.275,0.155],[0.261,0.141],[0.233,0.141],[0.219,0.155],[0.12,0.155],[0.106,0.141],[0.092,0.141],[0.078,0.155],[0.035,0.155],[0.014,0.134],[0.014,0.092]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{}}},"bounds":{"min":[-0.605,-0.09,-0.09],"max":[11.145,0.246,0.09]},"volume_in3":0.14231,"centroid":[4.9298,0.0558,0],"shell":[5.3167,0.0613,0],"area_in2":11.2721,"triangles":6148,"manifold":true,"slabs":[[-0.605,-0.09,-0.09,6.445,0.157,0.09],[6.445,-0.024,-0.09,7.228,0.235,0.09],[7.228,0.054,-0.09,11.145,0.246,0.09]],"slots":["tube"]},"aero-r-one-10-3-handguard":{"part":"aero-r-one-10-3-handguard","model":"aero-r-one-10-3-handguard.glb","script":"aero_r_one_10_3_handguard.py","inputs":{"aero-r-one-10-3-handguard.bottom_flat_width":0.609,"aero-r-one-10-3-handguard.height":1.95,"aero-r-one-10-3-handguard.inside_diameter":1.3,"aero-r-one-10-3-handguard.inside_height":1.65,"aero-r-one-10-3-handguard.lower_edge_below_rail_top":1.759,"aero-r-one-10-3-handguard.lower_edge_width":1.133,"aero-r-one-10-3-handguard.mlok_slot0_x":4.168,"aero-r-one-10-3-handguard.mlok_slots":4,"aero-r-one-10-3-handguard.qd_socket_d":0.37,"aero-r-one-10-3-handguard.qd_socket_from_rear":2.675,"aero-r-one-10-3-handguard.rail_bridge_recess":0.03,"aero-r-one-10-3-handguard.rail_centre_gap":0.365,"aero-r-one-10-3-handguard.rail_neck_foot_below_rail_top":0.377,"aero-r-one-10-3-handguard.rail_neck_width":0.62,"aero-r-one-10-3-handguard.rail_slot0_from_rear":0.821,"aero-r-one-10-3-handguard.rail_slots":25,"aero-r-one-10-3-handguard.rail_top_above_bore":1.2125,"aero-r-one-10-3-handguard.rail_window_length":0.54,"aero-r-one-10-3-handguard.rear_x":-0.763,"aero-r-one-10-3-handguard.short_slot_length":0.54,"aero-r-one-10-3-handguard.short_slot_rear_from_rear":3.432,"aero-r-one-10-3-handguard.side_flat_bottom_below_rail_top":1.502,"aero-r-one-10-3-handguard.side_flat_top_below_rail_top":0.88,"aero-r-one-10-3-handguard.side_top_width":1.455,"aero-r-one-10-3-handguard.thin_slot_count":8,"aero-r-one-10-3-handguard.thin_slot_first_from_rear":3.016,"aero-r-one-10-3-handguard.thin_slot_length":0.903,"aero-r-one-10-3-handguard.thin_slot_pitch":1.003,"aero-r-one-10-3-handguard.thin_slot_row_a_y":0.71,"aero-r-one-10-3-handguard.thin_slot_row_b_y":0.46,"aero-r-one-10-3-handguard.thin_slot_row_d_y":-0.41,"aero-r-one-10-3-handguard.thin_slot_row_e_y":-0.635,"aero-r-one-10-3-handguard.thin_slot_width":0.22,"aero-r-one-10-3-handguard.width":1.5,"std.mlok.slot_corner_r":0.0937007874015748,"std.mlok.slot_length":1.2598425196850394,"std.mlok.slot_pitch":1.574803149606299,"std.mlok.slot_width":0.2755905511811024,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{"side":[[0,-0.933],[0,-1.484],[0.012,-1.496],[0.012,-1.636],[0.035,-1.801],[0.076,-1.83],[0.305,-1.848],[0.328,-1.883],[0.34,-2.082],[0.358,-2.135],[0.628,-2.135],[0.639,-2.147],[1.097,-2.147],[1.144,-2.123],[1.161,-2.094],[1.138,-2.047],[1.161,-2.035],[1.161,-2],[1.132,-1.971],[1.085,-1.959],[1.044,-1.883],[1.044,-1.824],[1.073,-1.795],[1.414,-1.795],[1.466,-1.824],[1.49,-1.859],[1.49,-1.93],[1.373,-2.129],[1.39,-2.147],[1.66,-2.147],[1.766,-2.112],[1.895,-2.1],[2.082,-2.053],[2.153,-2.053],[2.387,-2.006],[2.986,-2.006],[3.115,-1.971],[10.493,-1.971],[10.505,-1.959],[10.611,-1.959],[10.628,-1.93],[10.675,-1.625],[10.675,-1.507],[10.687,-1.496],[10.675,-0.792],[10.652,-0.686],[10.64,-0.44],[10.628,-0.428],[10.628,-0.088],[10.64,-0.065],[10.611,0],[10.353,0],[10.329,-0.117],[10.218,-0.111],[10.229,-0.088],[10.212,0],[9.966,0],[9.942,-0.117],[9.836,-0.117],[9.813,0],[9.578,0],[9.561,-0.018],[9.555,-0.117],[9.438,-0.117],[9.414,0],[9.191,0],[9.174,-0.018],[9.168,-0.117],[9.039,-0.117],[9.033,-0.029],[9.015,0],[8.804,0],[8.775,-0.053],[8.787,-0.111],[8.675,-0.129],[8.634,-0.111],[8.634,-0.018],[8.616,0],[8.405,0],[8.388,-0.053],[8.394,-0.117],[8.265,-0.117],[8.253,-0.129],[8.235,-0.111],[8.229,0],[8.018,0],[8.001,-0.018],[7.995,-0.117],[7.889,-0.117],[7.877,-0.129],[7.836,-0.111],[7.848,-0.088],[7.83,0],[7.631,0],[7.613,-0.018],[7.608,-0.117],[7.502,-0.117],[7.49,-0.129],[7.467,-0.129],[7.437,-0.088],[7.449,-0.041],[7.432,0],[7.244,0],[7.215,-0.041],[7.226,-0.053],[7.22,-0.117],[7.103,-0.117],[7.091,-0.129],[7.05,-0.123],[7.05,-0.018],[7.033,0],[6.845,0],[6.827,-0.018],[6.827,-0.111],[6.763,-0.129],[6.657,-0.129],[6.652,-0.018],[6.634,0],[6.458,0],[6.44,-0.018],[6.452,-0.053],[6.44,-0.088],[6.464,-0.111],[6.388,-0.129],[6.259,-0.129],[6.253,-0.018],[6.235,0],[6.071,0],[6.041,-0.029],[6.053,-0.111],[6.036,-0.129],[6.024,-0.117],[6,-0.129],[5.86,-0.129],[5.854,-0.018],[5.836,0],[5.672,0],[5.654,-0.018],[5.666,-0.111],[5.649,-0.129],[5.473,-0.129],[5.455,-0.111],[5.449,0],[5.285,0],[5.267,-0.018],[5.267,-0.111],[5.25,-0.129],[5.074,-0.129],[5.056,-0.111],[5.05,0],[4.886,0],[4.868,-0.018],[4.88,-0.111],[4.851,-0.129],[4.675,-0.129],[4.669,-0.018],[4.651,0],[4.487,0],[4.47,-0.029],[4.481,-0.111],[4.452,-0.129],[4.276,-0.129],[4.27,-0.018],[4.253,0],[4.088,0],[4.071,-0.053],[4.082,-0.111],[4.053,-0.129],[3.889,-0.129],[3.883,-0.018],[3.854,0],[3.689,0],[3.684,-0.111],[3.666,-0.129],[3.502,-0.129],[3.484,-0.111],[3.496,-0.029],[3.467,0],[3.302,0],[3.285,-0.018],[3.285,-0.111],[3.267,-0.129],[3.103,-0.129],[3.097,-0.018],[3.068,0],[2.903,0],[2.886,-0.018],[2.886,-0.111],[2.868,-0.129],[2.716,-0.129],[2.71,-0.018],[2.669,0],[2.505,0],[2.487,-0.029],[2.481,-0.129],[2.329,-0.129],[2.323,-0.029],[2.293,0],[2.106,0],[2.088,-0.018],[2.082,-0.117],[1.93,-0.117],[1.924,-0.018],[1.906,0],[1.707,0],[1.689,-0.029],[1.683,-0.117],[1.543,-0.117],[1.537,-0.018],[1.507,0],[1.308,0],[1.29,-0.111],[1.261,-0.129],[1.249,-0.117],[1.156,-0.117],[1.15,-0.029],[1.12,0],[0.909,0],[0.903,-0.1],[0.886,-0.117],[0.768,-0.117],[0.751,-0.018],[0.733,0],[0.522,0],[0.504,-0.018],[0.499,-0.117],[0.346,-0.117],[0.334,-0.129],[0.311,-0.117],[0.293,-0.135],[0.305,-0.405],[0.287,-0.422],[0.194,-0.422],[0.059,-0.452],[0.035,-0.522],[0.012,-0.921]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"x":"rear_x","y":"rail_top_above_bore"}}},"bounds":{"min":[-0.763,-0.9345,-0.75],"max":[9.924,1.2125,0.75]},"volume_in3":4.3892,"centroid":[3.9521,0.233,0],"shell":[4.3846,0.2116,0],"area_in2":100.3156,"triangles":46972,"manifold":true,"slabs":[[-0.763,-0.923,-0.75,-0.367,1.094,0.75],[-0.367,-0.934,-0.75,1.216,1.212,0.75],[1.216,-0.866,-0.75,1.612,1.212,0.75],[1.612,-0.796,-0.75,2.404,1.212,0.75],[2.404,-0.738,-0.75,9.924,1.212,0.75]],"slots":["body"]},"aero-r-one-12-7-handguard":{"part":"aero-r-one-12-7-handguard","model":"aero-r-one-12-7-handguard.glb","script":"aero_r_one_12_7_handguard.py","inputs":{"aero-r-one-12-7-handguard.bottom_flat_width":0.609,"aero-r-one-12-7-handguard.height":1.95,"aero-r-one-12-7-handguard.inside_diameter":1.3,"aero-r-one-12-7-handguard.inside_height":1.65,"aero-r-one-12-7-handguard.lower_edge_below_rail_top":1.759,"aero-r-one-12-7-handguard.lower_edge_width":1.133,"aero-r-one-12-7-handguard.mlok_slot0_x":3.36,"aero-r-one-12-7-handguard.mlok_slots":6,"aero-r-one-12-7-handguard.qd_socket_d":0.37,"aero-r-one-12-7-handguard.qd_socket_from_rear":2.696,"aero-r-one-12-7-handguard.rail_bridge_recess":0.03,"aero-r-one-12-7-handguard.rail_centre_gap":0.365,"aero-r-one-12-7-handguard.rail_neck_foot_below_rail_top":0.377,"aero-r-one-12-7-handguard.rail_neck_width":0.62,"aero-r-one-12-7-handguard.rail_slot0_from_rear":0.813,"aero-r-one-12-7-handguard.rail_slots":31,"aero-r-one-12-7-handguard.rail_top_above_bore":1.2125,"aero-r-one-12-7-handguard.rail_window_length":0.54,"aero-r-one-12-7-handguard.rear_x":-0.763,"aero-r-one-12-7-handguard.side_flat_bottom_below_rail_top":1.502,"aero-r-one-12-7-handguard.side_flat_top_below_rail_top":0.88,"aero-r-one-12-7-handguard.side_top_width":1.455,"aero-r-one-12-7-handguard.thin_slot_count":10,"aero-r-one-12-7-handguard.thin_slot_first_from_rear":3.015,"aero-r-one-12-7-handguard.thin_slot_length":0.92,"aero-r-one-12-7-handguard.thin_slot_pitch":1.038,"aero-r-one-12-7-handguard.thin_slot_row_a_y":0.71,"aero-r-one-12-7-handguard.thin_slot_row_b_y":0.46,"aero-r-one-12-7-handguard.thin_slot_row_d_y":-0.41,"aero-r-one-12-7-handguard.thin_slot_row_e_y":-0.635,"aero-r-one-12-7-handguard.thin_slot_width":0.22,"aero-r-one-12-7-handguard.width":1.5,"std.mlok.slot_corner_r":0.0937007874015748,"std.mlok.slot_length":1.2598425196850394,"std.mlok.slot_pitch":1.574803149606299,"std.mlok.slot_width":0.2755905511811024,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{"side":[[0,-0.941],[0,-1.478],[0.014,-1.492],[0.028,-1.789],[0.092,-1.839],[0.304,-1.853],[0.339,-1.945],[0.354,-2.114],[0.375,-2.136],[0.785,-2.136],[0.799,-2.15],[1.068,-2.15],[1.16,-2.1],[1.146,-2.072],[1.16,-2.001],[1.075,-1.945],[1.047,-1.888],[1.047,-1.817],[1.068,-1.796],[1.393,-1.796],[1.421,-1.81],[1.471,-1.86],[1.471,-1.931],[1.358,-2.129],[1.379,-2.15],[1.605,-2.15],[1.747,-2.107],[2.072,-2.065],[2.086,-2.051],[2.327,-2.023],[2.341,-2.008],[2.977,-2.008],[3.062,-1.98],[11.067,-1.98],[11.082,-1.994],[11.096,-1.98],[11.506,-1.98],[11.52,-1.994],[11.562,-1.98],[11.605,-1.994],[11.69,-1.994],[11.704,-1.98],[12.029,-1.98],[12.072,-1.994],[12.114,-1.98],[12.128,-1.994],[12.213,-1.994],[12.227,-1.98],[12.241,-1.994],[12.948,-1.994],[12.97,-1.973],[12.984,-1.747],[12.998,-1.733],[12.998,-0.714],[12.984,-0.7],[12.984,-0.53],[12.97,-0.516],[12.97,-0.035],[12.948,-0.014],[12.722,-0.014],[12.701,-0.035],[12.694,-0.141],[12.567,-0.141],[12.56,-0.05],[12.538,-0.014],[12.326,-0.014],[12.319,-0.12],[12.27,-0.141],[12.185,-0.141],[12.164,-0.12],[12.164,-0.035],[12.142,-0.014],[11.93,-0.014],[11.923,-0.12],[11.902,-0.141],[11.859,-0.127],[11.789,-0.141],[11.768,-0.12],[11.768,-0.035],[11.746,-0.014],[11.548,-0.014],[11.527,-0.064],[11.527,-0.12],[11.449,-0.141],[11.421,-0.127],[11.393,-0.141],[11.371,-0.12],[11.371,-0.035],[11.35,-0.014],[11.152,-0.014],[11.145,-0.12],[11.124,-0.141],[11.096,-0.127],[10.983,-0.127],[10.975,-0.035],[10.954,-0.014],[10.756,-0.014],[10.742,-0.127],[10.629,-0.127],[10.615,-0.141],[10.579,-0.12],[10.579,-0.035],[10.558,-0.014],[10.374,-0.014],[10.353,-0.035],[10.367,-0.05],[10.353,-0.092],[10.367,-0.12],[10.332,-0.141],[10.318,-0.127],[10.19,-0.127],[10.183,-0.035],[10.162,-0.014],[9.978,-0.014],[9.964,-0.127],[9.794,-0.127],[9.787,-0.035],[9.766,-0.014],[9.582,-0.014],[9.582,-0.127],[9.398,-0.127],[9.391,-0.035],[9.37,-0.014],[9.186,-0.014],[9.172,-0.127],[9.031,-0.127],[9.017,-0.141],[8.995,-0.12],[8.995,-0.035],[8.974,-0.014],[8.79,-0.014],[8.79,-0.127],[8.606,-0.127],[8.585,-0.064],[8.599,-0.035],[8.578,-0.014],[8.408,-0.014],[8.394,-0.127],[8.196,-0.127],[8.182,-0.014],[8.012,-0.014],[7.998,-0.127],[7.8,-0.127],[7.786,-0.014],[7.616,-0.014],[7.602,-0.127],[7.404,-0.127],[7.39,-0.014],[7.22,-0.014],[7.206,-0.127],[7.022,-0.127],[7.001,-0.106],[7.015,-0.021],[6.994,0],[6.98,-0.014],[6.824,-0.014],[6.81,-0.127],[6.612,-0.127],[6.605,-0.05],[6.619,-0.021],[6.598,0],[6.584,-0.014],[6.428,-0.014],[6.414,-0.127],[6.23,-0.127],[6.216,-0.014],[6.032,-0.014],[6.018,-0.127],[5.82,-0.127],[5.82,0],[5.806,-0.014],[5.636,-0.014],[5.622,-0.127],[5.452,-0.127],[5.445,-0.021],[5.424,0],[5.396,-0.014],[5.297,-0.014],[5.283,0],[5.24,-0.014],[5.226,-0.127],[5.042,-0.127],[5.042,0],[4.887,0],[4.844,-0.014],[4.83,-0.127],[4.674,-0.127],[4.653,-0.106],[4.646,0],[4.491,0],[4.448,-0.014],[4.434,-0.127],[4.278,-0.127],[4.257,-0.106],[4.271,-0.021],[4.25,0],[4.095,0],[4.052,-0.014],[4.038,-0.127],[3.882,-0.127],[3.875,-0.021],[3.854,0],[3.699,0],[3.656,-0.014],[3.642,-0.127],[3.501,-0.127],[3.479,-0.106],[3.472,0],[3.303,0],[3.274,-0.014],[3.253,-0.035],[3.246,-0.127],[3.105,-0.127],[3.097,-0.021],[3.076,0],[2.921,0],[2.878,-0.014],[2.857,-0.05],[2.85,-0.127],[2.723,-0.127],[2.701,-0.106],[2.694,0],[2.525,0],[2.482,-0.014],[2.454,-0.127],[2.327,-0.127],[2.298,0],[2.143,0],[2.129,-0.014],[2.086,-0.014],[2.065,-0.078],[2.079,-0.106],[2.058,-0.127],[1.931,-0.127],[1.924,-0.021],[1.902,0],[1.747,0],[1.733,-0.014],[1.69,-0.014],[1.683,-0.106],[1.662,-0.127],[1.549,-0.127],[1.528,-0.106],[1.52,0],[1.294,-0.014],[1.287,-0.106],[1.266,-0.127],[1.167,-0.127],[1.146,-0.106],[1.146,-0.021],[1.124,0],[0.969,0],[0.955,-0.014],[0.912,-0.014],[0.891,-0.035],[0.884,-0.127],[0.771,-0.127],[0.743,0],[0.587,0],[0.509,-0.021],[0.488,-0.127],[0.297,-0.134],[0.311,-0.389],[0.29,-0.41],[0.248,-0.424],[0.134,-0.424],[0.12,-0.438],[0.078,-0.438],[0.057,-0.46],[0.042,-0.488],[0.042,-0.615],[0.028,-0.629],[0.014,-0.926]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"x":"rear_x","y":"rail_top_above_bore"}}},"bounds":{"min":[-0.763,-0.9375,-0.75],"max":[12.235,1.2125,0.75]},"volume_in3":5.1792,"centroid":[5.0583,0.2506,0],"shell":[5.5333,0.2175,0],"area_in2":120.6782,"triangles":57680,"manifold":true,"slabs":[[-0.763,-0.924,-0.75,-0.369,1.094,0.75],[-0.369,-0.938,-0.75,1.206,1.212,0.75],[1.206,-0.866,-0.75,1.6,1.212,0.75],[1.6,-0.795,-0.75,2.388,1.212,0.75],[2.388,-0.738,-0.75,12.235,1.212,0.75]],"slots":["body"]},"aero-r-one-15-handguard":{"part":"aero-r-one-15-handguard","model":"aero-r-one-15-handguard.glb","script":"aero_r_one_15_handguard.py","inputs":{"aero-r-one-15-handguard.bottom_flat_width":0.609,"aero-r-one-15-handguard.height":1.95,"aero-r-one-15-handguard.inside_diameter":1.3,"aero-r-one-15-handguard.inside_height":1.65,"aero-r-one-15-handguard.lower_edge_below_rail_top":1.759,"aero-r-one-15-handguard.lower_edge_width":1.133,"aero-r-one-15-handguard.mlok_slot0_x":4.134,"aero-r-one-15-handguard.mlok_slots":7,"aero-r-one-15-handguard.qd_socket_d":0.37,"aero-r-one-15-handguard.qd_socket_from_rear":2.685,"aero-r-one-15-handguard.rail_bridge_recess":0.03,"aero-r-one-15-handguard.rail_centre_gap":0.365,"aero-r-one-15-handguard.rail_neck_foot_below_rail_top":0.377,"aero-r-one-15-handguard.rail_neck_width":0.62,"aero-r-one-15-handguard.rail_slot0_from_rear":0.855,"aero-r-one-15-handguard.rail_slots":37,"aero-r-one-15-handguard.rail_top_above_bore":1.2125,"aero-r-one-15-handguard.rail_window_length":0.54,"aero-r-one-15-handguard.rear_x":-0.763,"aero-r-one-15-handguard.short_slot_length":0.317,"aero-r-one-15-handguard.short_slot_rear_from_rear":3.539,"aero-r-one-15-handguard.side_flat_bottom_below_rail_top":1.502,"aero-r-one-15-handguard.side_flat_top_below_rail_top":0.88,"aero-r-one-15-handguard.side_top_width":1.455,"aero-r-one-15-handguard.thin_slot_count":12,"aero-r-one-15-handguard.thin_slot_first_from_rear":2.987,"aero-r-one-15-handguard.thin_slot_length":0.954,"aero-r-one-15-handguard.thin_slot_pitch":1.0685,"aero-r-one-15-handguard.thin_slot_row_a_y":0.71,"aero-r-one-15-handguard.thin_slot_row_b_y":0.46,"aero-r-one-15-handguard.thin_slot_row_d_y":-0.41,"aero-r-one-15-handguard.thin_slot_row_e_y":-0.635,"aero-r-one-15-handguard.thin_slot_width":0.22,"aero-r-one-15-handguard.width":1.5,"std.mlok.slot_corner_r":0.0937007874015748,"std.mlok.slot_length":1.2598425196850394,"std.mlok.slot_pitch":1.574803149606299,"std.mlok.slot_width":0.2755905511811024,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{"side":[[0,-0.861],[0,-1.529],[0.017,-1.546],[0.033,-1.763],[0.075,-1.805],[0.125,-1.805],[0.142,-1.822],[0.276,-1.822],[0.309,-1.839],[0.351,-1.914],[0.351,-1.997],[0.368,-2.014],[0.376,-2.106],[0.51,-2.106],[0.526,-2.123],[1.011,-2.123],[1.028,-2.139],[1.045,-2.123],[1.095,-2.139],[1.128,-2.106],[1.203,-2.081],[1.17,-2.031],[1.17,-1.981],[1.12,-1.93],[1.086,-1.847],[1.128,-1.772],[1.396,-1.772],[1.454,-1.813],[1.471,-1.847],[1.471,-1.914],[1.437,-1.947],[1.437,-1.981],[1.371,-2.081],[1.371,-2.114],[1.412,-2.139],[1.446,-2.123],[1.646,-2.123],[1.713,-2.089],[1.88,-2.073],[1.897,-2.056],[1.997,-2.056],[2.014,-2.039],[2.081,-2.039],[2.098,-2.022],[2.281,-2.006],[2.298,-1.989],[2.933,-1.989],[2.95,-1.972],[3.05,-1.972],[3.067,-1.956],[6.56,-1.956],[6.577,-1.972],[6.627,-1.972],[6.644,-1.956],[6.777,-1.956],[6.794,-1.972],[13.597,-1.972],[13.613,-1.989],[15.318,-1.989],[15.343,-1.947],[15.343,-1.797],[15.36,-1.78],[15.36,-0.627],[15.343,-0.61],[15.343,-0.025],[15.318,0],[15.151,0],[15.126,-0.025],[15.118,-0.117],[15.068,-0.117],[15.051,-0.1],[15.001,-0.117],[14.976,-0.092],[14.951,0],[14.75,0],[14.733,-0.1],[14.583,-0.1],[14.574,-0.025],[14.549,0],[14.349,0],[14.34,-0.025],[14.357,-0.042],[14.332,-0.1],[14.182,-0.1],[14.165,0],[13.948,0],[13.931,-0.1],[13.781,-0.1],[13.764,0],[13.563,0],[13.563,-0.1],[13.379,-0.1],[13.363,0],[13.162,0],[13.145,-0.1],[12.978,-0.1],[12.962,0],[12.778,0],[12.778,-0.1],[12.577,-0.1],[12.56,0],[12.377,0],[12.36,-0.1],[12.176,-0.1],[12.159,0],[11.975,0],[11.975,-0.1],[11.792,-0.1],[11.775,0],[11.591,0],[11.574,-0.1],[11.39,-0.1],[11.374,0],[11.19,0],[11.19,-0.1],[10.989,-0.1],[10.973,0],[10.805,0],[10.789,-0.1],[10.588,-0.1],[10.571,0],[10.404,0],[10.388,-0.1],[10.187,-0.1],[10.17,0],[10.003,0],[9.987,-0.1],[9.786,-0.1],[9.786,0],[9.602,0],[9.585,-0.1],[9.402,-0.1],[9.385,0],[9.201,0],[9.184,-0.1],[9,-0.1],[9,0],[8.817,0],[8.8,-0.1],[8.616,-0.1],[8.599,0],[8.415,0],[8.399,-0.1],[8.198,-0.1],[8.198,0],[8.014,0],[7.998,-0.1],[7.83,-0.1],[7.814,0],[7.613,0],[7.596,-0.1],[7.413,-0.1],[7.413,0],[7.229,0],[7.204,-0.025],[7.22,-0.042],[7.195,-0.1],[7.045,-0.1],[7.028,0],[6.828,0],[6.819,-0.075],[6.794,-0.1],[6.644,-0.1],[6.619,-0.042],[6.635,-0.025],[6.627,0],[6.426,0],[6.41,-0.1],[6.259,-0.1],[6.243,0],[6.025,0],[6.009,-0.1],[5.858,-0.1],[5.841,0],[5.641,0],[5.616,-0.025],[5.607,-0.1],[5.474,-0.1],[5.457,0],[5.24,0],[5.223,-0.1],[5.073,-0.1],[5.073,0],[4.839,0],[4.822,-0.1],[4.688,-0.1],[4.672,0],[4.454,0],[4.429,-0.025],[4.421,-0.1],[4.304,-0.1],[4.287,0],[4.053,0],[4.036,-0.1],[3.903,-0.1],[3.894,-0.075],[3.911,-0.058],[3.886,0],[3.652,0],[3.635,-0.1],[3.518,-0.1],[3.502,0],[3.268,0],[3.251,-0.1],[3.134,-0.1],[3.117,0],[2.866,0],[2.85,-0.1],[2.749,-0.1],[2.733,0],[2.482,0],[2.465,-0.1],[2.365,-0.1],[2.332,0],[2.081,0],[2.064,-0.1],[1.981,-0.1],[1.947,0],[1.696,0],[1.663,-0.1],[1.579,-0.1],[1.563,0],[1.312,0],[1.287,-0.042],[1.279,-0.1],[1.195,-0.1],[1.178,0],[0.911,0],[0.894,-0.1],[0.811,-0.1],[0.802,-0.025],[0.777,0],[0.526,0],[0.493,-0.1],[0.301,-0.109],[0.301,-0.159],[0.318,-0.175],[0.318,-0.376],[0.292,-0.401],[0.109,-0.418],[0.067,-0.443],[0.05,-0.476],[0.05,-0.577],[0.033,-0.593],[0.017,-0.844]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"x":"rear_x","y":"rail_top_above_bore"}}},"bounds":{"min":[-0.763,-0.9265,-0.75],"max":[14.597,1.2125,0.75]},"volume_in3":5.9151,"centroid":[6.2192,0.2727,0],"shell":[6.7066,0.2239,0],"area_in2":141.0237,"triangles":69182,"manifold":true,"slabs":[[-0.763,-0.893,-0.75,-0.369,1.094,0.75],[-0.369,-0.926,-0.75,1.206,1.212,0.75],[1.206,-0.844,-0.75,1.6,1.212,0.75],[1.6,-0.738,-0.75,14.597,1.212,0.75]],"slots":["body"]},"aero-r-one-16-6-handguard":{"part":"aero-r-one-16-6-handguard","model":"aero-r-one-16-6-handguard.glb","script":"aero_r_one_16_6_handguard.py","inputs":{"aero-r-one-16-6-handguard.bottom_flat_width":0.609,"aero-r-one-16-6-handguard.height":1.95,"aero-r-one-16-6-handguard.inside_diameter":1.3,"aero-r-one-16-6-handguard.inside_height":1.65,"aero-r-one-16-6-handguard.lower_edge_below_rail_top":1.759,"aero-r-one-16-6-handguard.lower_edge_width":1.133,"aero-r-one-16-6-handguard.mlok_slot0_x":4.106,"aero-r-one-16-6-handguard.mlok_slots":8,"aero-r-one-16-6-handguard.qd_socket_d":0.37,"aero-r-one-16-6-handguard.qd_socket_from_rear":2.613,"aero-r-one-16-6-handguard.rail_bridge_recess":0.03,"aero-r-one-16-6-handguard.rail_centre_gap":0.365,"aero-r-one-16-6-handguard.rail_neck_foot_below_rail_top":0.377,"aero-r-one-16-6-handguard.rail_neck_width":0.62,"aero-r-one-16-6-handguard.rail_slot0_from_rear":0.797,"aero-r-one-16-6-handguard.rail_slots":41,"aero-r-one-16-6-handguard.rail_top_above_bore":1.2125,"aero-r-one-16-6-handguard.rail_window_length":0.54,"aero-r-one-16-6-handguard.rear_x":-0.763,"aero-r-one-16-6-handguard.short_slot_length":0.593,"aero-r-one-16-6-handguard.short_slot_rear_from_rear":3.345,"aero-r-one-16-6-handguard.side_flat_bottom_below_rail_top":1.502,"aero-r-one-16-6-handguard.side_flat_top_below_rail_top":0.88,"aero-r-one-16-6-handguard.side_top_width":1.455,"aero-r-one-16-6-handguard.thin_slot_count":13,"aero-r-one-16-6-handguard.thin_slot_first_from_rear":3.043,"aero-r-one-16-6-handguard.thin_slot_length":1.001,"aero-r-one-16-6-handguard.thin_slot_pitch":1.099,"aero-r-one-16-6-handguard.thin_slot_row_a_y":0.71,"aero-r-one-16-6-handguard.thin_slot_row_b_y":0.46,"aero-r-one-16-6-handguard.thin_slot_row_d_y":-0.41,"aero-r-one-16-6-handguard.thin_slot_row_e_y":-0.635,"aero-r-one-16-6-handguard.thin_slot_width":0.22,"aero-r-one-16-6-handguard.width":1.5,"std.mlok.slot_corner_r":0.0937007874015748,"std.mlok.slot_length":1.2598425196850394,"std.mlok.slot_pitch":1.574803149606299,"std.mlok.slot_width":0.2755905511811024,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{"side":[[0,-0.491],[0,-1.807],[0.046,-1.835],[0.158,-1.835],[0.176,-1.854],[0.278,-1.863],[0.278,-2.03],[0.297,-2.048],[0.306,-2.15],[1.047,-2.15],[1.057,-2.123],[1.038,-2.085],[1.094,-2.048],[1.094,-2.011],[1.047,-1.965],[1.029,-1.983],[0.992,-1.965],[0.973,-1.983],[0.927,-1.919],[0.945,-1.844],[0.992,-1.798],[1.4,-1.798],[1.464,-1.863],[1.464,-1.919],[1.409,-1.993],[1.335,-2.141],[1.566,-2.15],[1.585,-2.132],[1.659,-2.132],[1.678,-2.113],[1.752,-2.113],[1.77,-2.095],[1.863,-2.095],[1.882,-2.076],[1.956,-2.076],[1.974,-2.058],[2.067,-2.058],[2.085,-2.039],[2.16,-2.039],[2.178,-2.021],[2.326,-2.021],[2.345,-2.002],[2.901,-2.002],[2.92,-1.983],[3.012,-1.983],[3.031,-1.965],[16.841,-1.965],[16.869,-1.937],[16.869,-1.844],[16.887,-1.826],[16.887,-1.659],[16.906,-1.641],[16.906,-0.769],[16.887,-0.751],[16.887,-0.584],[16.869,-0.565],[16.869,-0.399],[16.85,-0.38],[16.869,-0.028],[16.841,0],[16.6,0],[16.572,-0.102],[16.545,-0.13],[16.526,-0.111],[16.489,-0.13],[16.461,-0.102],[16.461,-0.046],[16.433,0],[16.211,0],[16.202,-0.065],[16.174,-0.111],[16.081,-0.111],[16.053,-0.083],[16.044,0],[15.822,0],[15.794,-0.102],[15.766,-0.13],[15.692,-0.13],[15.664,-0.102],[15.655,0],[15.432,0],[15.404,-0.028],[15.423,-0.046],[15.404,-0.065],[15.404,-0.102],[15.377,-0.13],[15.303,-0.13],[15.275,-0.102],[15.265,0],[15.043,0],[15.015,-0.028],[15.015,-0.102],[14.987,-0.13],[14.913,-0.13],[14.885,-0.102],[14.876,0],[14.654,0],[14.626,-0.028],[14.617,-0.13],[14.505,-0.13],[14.496,-0.028],[14.468,0],[14.264,0],[14.237,-0.028],[14.227,-0.13],[14.116,-0.13],[14.088,-0.083],[14.079,0],[13.875,0],[13.847,-0.028],[13.838,-0.13],[13.727,-0.13],[13.699,-0.102],[13.69,0],[13.486,0],[13.458,-0.028],[13.449,-0.13],[13.319,-0.13],[13.3,0],[13.078,0],[13.06,-0.13],[12.93,-0.13],[12.92,-0.028],[12.893,0],[12.707,0],[12.679,-0.028],[12.679,-0.102],[12.652,-0.13],[12.54,-0.13],[12.513,-0.083],[12.531,-0.065],[12.503,0],[12.299,0],[12.29,-0.102],[12.262,-0.13],[12.151,-0.13],[12.123,-0.102],[12.114,0],[11.91,0],[11.873,-0.13],[11.743,-0.13],[11.725,0],[11.521,0],[11.493,-0.028],[11.484,-0.13],[11.354,-0.13],[11.345,-0.028],[11.317,0],[11.132,0],[11.095,-0.13],[10.965,-0.13],[10.937,-0.102],[10.928,0],[10.742,0],[10.715,-0.028],[10.705,-0.13],[10.557,-0.13],[10.538,0],[10.353,0],[10.325,-0.028],[10.316,-0.13],[10.168,-0.13],[10.158,-0.028],[10.131,0],[9.964,0],[9.936,-0.028],[9.927,-0.13],[9.778,-0.13],[9.751,-0.102],[9.741,0],[9.575,0],[9.547,-0.028],[9.547,-0.065],[9.528,-0.083],[9.547,-0.102],[9.537,-0.13],[9.371,-0.13],[9.352,0],[9.167,0],[9.139,-0.028],[9.13,-0.13],[8.981,-0.13],[8.972,-0.028],[8.944,0],[8.777,0],[8.75,-0.028],[8.74,-0.13],[8.592,-0.13],[8.564,-0.102],[8.583,-0.083],[8.583,-0.028],[8.555,0],[8.388,0],[8.36,-0.028],[8.351,-0.13],[8.184,-0.13],[8.166,0],[7.98,0],[7.962,-0.13],[7.795,-0.13],[7.786,-0.028],[7.758,0],[7.61,0],[7.582,-0.028],[7.572,-0.13],[7.406,-0.13],[7.378,-0.102],[7.396,-0.083],[7.378,-0.065],[7.396,-0.028],[7.369,0],[7.202,0],[7.174,-0.028],[7.192,-0.046],[7.183,-0.13],[6.998,-0.13],[6.979,0],[6.812,0],[6.785,-0.028],[6.775,-0.13],[6.609,-0.13],[6.599,-0.028],[6.571,0],[6.423,0],[6.395,-0.028],[6.386,-0.13],[6.219,-0.13],[6.191,-0.102],[6.21,-0.065],[6.191,-0.046],[6.21,-0.028],[6.182,0],[6.034,0],[6.006,-0.028],[5.997,-0.13],[5.811,-0.13],[5.793,0],[5.626,0],[5.608,-0.13],[5.422,-0.13],[5.413,-0.028],[5.385,0],[5.237,0],[5.209,-0.028],[5.209,-0.083],[5.228,-0.102],[5.2,-0.13],[5.033,-0.13],[5.005,-0.102],[4.996,0],[4.847,0],[4.82,-0.028],[4.81,-0.13],[4.625,-0.13],[4.607,0],[4.44,0],[4.421,-0.13],[4.236,-0.13],[4.208,-0.083],[4.226,-0.065],[4.226,-0.028],[4.199,0],[4.05,0],[4.032,-0.13],[3.846,-0.13],[3.819,-0.102],[3.809,0],[3.661,0],[3.633,-0.028],[3.624,-0.13],[3.439,-0.13],[3.429,-0.028],[3.402,0],[3.253,0],[3.235,-0.13],[3.049,-0.13],[3.04,-0.028],[3.012,0],[2.864,0],[2.855,-0.102],[2.827,-0.13],[2.642,-0.13],[2.623,0],[2.475,0],[2.447,-0.028],[2.438,-0.13],[2.252,-0.13],[2.243,-0.028],[2.215,0],[2.067,0],[2.048,-0.13],[1.863,-0.13],[1.835,-0.102],[1.854,-0.028],[1.826,0],[1.678,0],[1.65,-0.028],[1.641,-0.13],[1.474,-0.13],[1.446,-0.102],[1.464,-0.083],[1.464,-0.046],[1.437,0],[1.27,0],[1.251,-0.13],[1.066,-0.13],[1.038,-0.102],[1.057,-0.028],[1.029,0],[0.881,0],[0.871,-0.102],[0.843,-0.13],[0.658,-0.13],[0.649,-0.065],[0.667,-0.028],[0.64,0],[0.491,0],[0.463,-0.028],[0.454,-0.13],[0.26,-0.139],[0.26,-0.417],[0.158,-0.426],[0.139,-0.445],[0.046,-0.445]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"x":"rear_x","y":"rail_top_above_bore"}}},"bounds":{"min":[-0.763,-0.9375,-0.75],"max":[16.143,1.2125,0.75]},"volume_in3":6.423,"centroid":[6.908,0.2752,0],"shell":[7.4342,0.2242,-0.0002],"area_in2":154.3676,"triangles":76002,"manifold":true,"slabs":[[-0.763,-0.938,-0.75,-0.34,1.094,0.75],[-0.34,-0.938,-0.75,1.35,1.212,0.75],[1.35,-0.826,-0.75,2.196,1.212,0.75],[2.196,-0.738,-0.75,16.143,1.212,0.75]],"slots":["body"]},"aero-r-one-7-3-handguard":{"part":"aero-r-one-7-3-handguard","model":"aero-r-one-7-3-handguard.glb","script":"aero_r_one_7_3_handguard.py","inputs":{"aero-r-one-7-3-handguard.bottom_flat_width":0.609,"aero-r-one-7-3-handguard.height":1.95,"aero-r-one-7-3-handguard.inside_diameter":1.3,"aero-r-one-7-3-handguard.inside_height":1.65,"aero-r-one-7-3-handguard.lower_edge_below_rail_top":1.759,"aero-r-one-7-3-handguard.lower_edge_width":1.133,"aero-r-one-7-3-handguard.mlok_slot0_x":4.266,"aero-r-one-7-3-handguard.mlok_slots":2,"aero-r-one-7-3-handguard.qd_socket_d":0.37,"aero-r-one-7-3-handguard.qd_socket_from_rear":2.818,"aero-r-one-7-3-handguard.rail_bridge_recess":0.03,"aero-r-one-7-3-handguard.rail_centre_gap":0.365,"aero-r-one-7-3-handguard.rail_neck_foot_below_rail_top":0.377,"aero-r-one-7-3-handguard.rail_neck_width":0.62,"aero-r-one-7-3-handguard.rail_slot0_from_rear":0.798,"aero-r-one-7-3-handguard.rail_slots":17,"aero-r-one-7-3-handguard.rail_top_above_bore":1.2125,"aero-r-one-7-3-handguard.rail_window_length":0.54,"aero-r-one-7-3-handguard.rear_x":-0.763,"aero-r-one-7-3-handguard.short_slot_length":0.48,"aero-r-one-7-3-handguard.short_slot_rear_from_rear":3.607,"aero-r-one-7-3-handguard.side_flat_bottom_below_rail_top":1.502,"aero-r-one-7-3-handguard.side_flat_top_below_rail_top":0.88,"aero-r-one-7-3-handguard.side_top_width":1.455,"aero-r-one-7-3-handguard.thin_slot_count":5,"aero-r-one-7-3-handguard.thin_slot_first_from_rear":3.105,"aero-r-one-7-3-handguard.thin_slot_length":0.845,"aero-r-one-7-3-handguard.thin_slot_pitch":0.977,"aero-r-one-7-3-handguard.thin_slot_row_a_y":0.71,"aero-r-one-7-3-handguard.thin_slot_row_b_y":0.46,"aero-r-one-7-3-handguard.thin_slot_row_d_y":-0.41,"aero-r-one-7-3-handguard.thin_slot_row_e_y":-0.635,"aero-r-one-7-3-handguard.thin_slot_width":0.22,"aero-r-one-7-3-handguard.width":1.5,"std.mlok.slot_corner_r":0.0937007874015748,"std.mlok.slot_length":1.2598425196850394,"std.mlok.slot_pitch":1.574803149606299,"std.mlok.slot_width":0.2755905511811024,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{"side":[[0,-0.889],[0,-1.526],[0.025,-1.808],[0.103,-1.837],[0.298,-1.849],[0.335,-2.134],[1.071,-2.143],[1.125,-2.114],[1.1,-2.064],[1.133,-2.031],[1.133,-1.998],[1.08,-1.961],[1.063,-1.969],[1.034,-1.94],[1.001,-1.849],[1.018,-1.808],[1.03,-1.795],[1.41,-1.795],[1.464,-1.841],[1.481,-1.89],[1.357,-2.122],[1.394,-2.151],[1.65,-2.143],[1.725,-2.118],[2.436,-2.01],[3.082,-2.002],[3.222,-1.969],[7.549,-1.969],[7.569,-1.899],[7.586,-1.675],[7.586,-0.773],[7.561,-0.434],[7.569,-0.037],[7.557,0],[7.201,-0.008],[7.185,-0.124],[7.036,-0.124],[7.015,-0.087],[7.023,-0.045],[7.011,0],[6.821,0],[6.8,-0.021],[6.796,-0.124],[6.639,-0.124],[6.614,0],[6.424,0],[6.411,-0.012],[6.411,-0.103],[6.436,-0.112],[6.407,-0.124],[6.242,-0.124],[6.221,-0.103],[6.217,0],[6.035,0],[6.022,-0.012],[6.018,-0.124],[5.845,-0.124],[5.82,0],[5.638,-0.008],[5.625,-0.037],[5.642,-0.045],[5.642,-0.112],[5.63,-0.124],[5.448,-0.124],[5.427,-0.095],[5.435,-0.029],[5.423,0],[5.249,0],[5.232,-0.124],[5.05,-0.124],[5.026,0],[4.86,0],[4.848,-0.012],[4.844,-0.124],[4.645,-0.124],[4.633,-0.087],[4.641,-0.012],[4.629,0],[4.463,0],[4.451,-0.012],[4.447,-0.124],[4.248,-0.124],[4.244,-0.012],[4.231,0],[4.066,0],[4.049,-0.124],[3.851,-0.124],[3.847,-0.012],[3.834,0],[3.669,0],[3.657,-0.021],[3.665,-0.112],[3.652,-0.124],[3.454,-0.124],[3.45,-0.045],[3.466,-0.029],[3.437,0],[3.272,0],[3.255,-0.124],[3.073,-0.124],[3.069,-0.021],[3.04,0],[2.883,0],[2.858,-0.124],[2.66,-0.124],[2.656,-0.045],[2.676,-0.041],[2.68,-0.021],[2.643,0],[2.486,0],[2.461,-0.124],[2.287,-0.124],[2.283,-0.012],[2.254,0],[2.089,0],[2.064,-0.124],[1.899,-0.124],[1.894,-0.012],[1.857,0],[1.692,0],[1.667,-0.124],[1.51,-0.124],[1.506,-0.021],[1.46,0],[1.295,0],[1.27,-0.124],[1.121,-0.124],[1.117,-0.037],[1.088,0],[0.898,0],[0.873,-0.124],[0.732,-0.124],[0.716,-0.008],[0.509,0],[0.488,-0.021],[0.484,-0.124],[0.294,-0.124],[0.281,-0.136],[0.281,-0.418],[0.062,-0.447],[0.033,-0.476]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"x":"rear_x","y":"rail_top_above_bore"}}},"bounds":{"min":[-0.763,-0.9385,-0.75],"max":[6.823,1.2125,0.75]},"volume_in3":3.4266,"centroid":[2.563,0.1958,0],"shell":[2.885,0.1981,0],"area_in2":73.9998,"triangles":30616,"manifold":true,"slabs":[[-0.763,-0.922,-0.75,-0.364,1.094,0.75],[-0.364,-0.938,-0.75,1.233,1.212,0.75],[1.233,-0.864,-0.75,1.633,1.212,0.75],[1.633,-0.804,-0.75,2.83,1.212,0.75],[2.83,-0.738,-0.75,6.823,1.212,0.75]],"slots":["body"]},"aero-r-one-9-3-handguard":{"part":"aero-r-one-9-3-handguard","model":"aero-r-one-9-3-handguard.glb","script":"aero_r_one_9_3_handguard.py","inputs":{"aero-r-one-9-3-handguard.bottom_flat_width":0.609,"aero-r-one-9-3-handguard.height":1.95,"aero-r-one-9-3-handguard.inside_diameter":1.3,"aero-r-one-9-3-handguard.inside_height":1.65,"aero-r-one-9-3-handguard.lower_edge_below_rail_top":1.759,"aero-r-one-9-3-handguard.lower_edge_width":1.133,"aero-r-one-9-3-handguard.mlok_slot0_x":3.128,"aero-r-one-9-3-handguard.mlok_slots":4,"aero-r-one-9-3-handguard.qd_socket_d":0.37,"aero-r-one-9-3-handguard.qd_socket_from_rear":2.568,"aero-r-one-9-3-handguard.rail_bridge_recess":0.03,"aero-r-one-9-3-handguard.rail_centre_gap":0.365,"aero-r-one-9-3-handguard.rail_neck_foot_below_rail_top":0.377,"aero-r-one-9-3-handguard.rail_neck_width":0.62,"aero-r-one-9-3-handguard.rail_slot0_from_rear":0.828,"aero-r-one-9-3-handguard.rail_slots":22,"aero-r-one-9-3-handguard.rail_top_above_bore":1.2125,"aero-r-one-9-3-handguard.rail_window_length":0.54,"aero-r-one-9-3-handguard.rear_x":-0.763,"aero-r-one-9-3-handguard.side_flat_bottom_below_rail_top":1.502,"aero-r-one-9-3-handguard.side_flat_top_below_rail_top":0.88,"aero-r-one-9-3-handguard.side_top_width":1.455,"aero-r-one-9-3-handguard.thin_slot_count":7,"aero-r-one-9-3-handguard.thin_slot_first_from_rear":2.871,"aero-r-one-9-3-handguard.thin_slot_length":0.892,"aero-r-one-9-3-handguard.thin_slot_pitch":1.018,"aero-r-one-9-3-handguard.thin_slot_row_a_y":0.71,"aero-r-one-9-3-handguard.thin_slot_row_b_y":0.46,"aero-r-one-9-3-handguard.thin_slot_row_d_y":-0.41,"aero-r-one-9-3-handguard.thin_slot_row_e_y":-0.635,"aero-r-one-9-3-handguard.thin_slot_width":0.22,"aero-r-one-9-3-handguard.width":1.5,"std.mlok.slot_corner_r":0.0937007874015748,"std.mlok.slot_length":1.2598425196850394,"std.mlok.slot_pitch":1.574803149606299,"std.mlok.slot_width":0.2755905511811024,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{"side":[[0,-0.886],[0,-1.526],[0.031,-1.788],[0.058,-1.814],[0.1,-1.824],[0.304,-1.84],[0.336,-1.914],[0.362,-2.118],[0.886,-2.129],[0.896,-2.139],[1.012,-2.129],[1.075,-2.139],[1.164,-2.102],[1.164,-2.071],[1.143,-2.05],[1.164,-1.987],[1.127,-1.95],[1.075,-1.95],[1.08,-1.924],[1.049,-1.872],[1.049,-1.809],[1.085,-1.782],[1.421,-1.793],[1.468,-1.84],[1.478,-1.914],[1.363,-2.102],[1.379,-2.139],[1.599,-2.139],[2.186,-2.003],[2.784,-2.003],[2.899,-1.961],[9.557,-1.971],[9.584,-1.788],[9.584,-1.515],[9.594,-1.505],[9.594,-0.938],[9.584,-0.928],[9.594,-0.886],[9.563,-0.393],[9.573,-0.026],[9.557,0],[9.201,0],[9.18,-0.115],[9.023,-0.115],[9.017,-0.016],[9.002,0],[8.813,0],[8.797,-0.016],[8.792,-0.115],[8.687,-0.126],[8.677,-0.115],[8.635,-0.126],[8.619,-0.11],[8.619,-0.016],[8.603,0],[8.414,0],[8.42,-0.058],[8.399,-0.1],[8.43,-0.11],[8.351,-0.126],[8.226,-0.115],[8.22,-0.016],[8.205,0],[8.026,0],[8.011,-0.016],[8.005,-0.115],[7.827,-0.115],[7.822,-0.016],[7.806,0],[7.628,0],[7.612,-0.026],[7.633,-0.047],[7.633,-0.11],[7.607,-0.126],[7.429,-0.115],[7.418,0],[7.24,0],[7.224,-0.016],[7.224,-0.11],[7.198,-0.126],[7.03,-0.115],[7.02,0],[6.842,0],[6.831,-0.115],[6.632,-0.115],[6.621,0],[6.454,0],[6.438,-0.016],[6.433,-0.115],[6.286,-0.126],[6.228,-0.11],[6.223,0],[6.055,0],[6.04,-0.016],[6.05,-0.089],[6.034,-0.115],[5.846,-0.115],[5.84,-0.016],[5.825,0],[5.657,0],[5.641,-0.016],[5.641,-0.11],[5.604,-0.126],[5.437,-0.115],[5.431,-0.058],[5.452,-0.037],[5.437,0],[5.258,0],[5.243,-0.058],[5.253,-0.11],[5.227,-0.126],[5.059,-0.115],[5.049,0],[4.86,0],[4.855,-0.079],[4.844,-0.11],[4.818,-0.126],[4.65,-0.115],[4.645,-0.047],[4.666,-0.037],[4.65,0],[4.461,0],[4.456,-0.11],[4.42,-0.126],[4.273,-0.115],[4.278,-0.026],[4.262,0],[4.074,0],[4.058,-0.016],[4.058,-0.11],[4.042,-0.126],[4.011,-0.115],[3.864,-0.126],[3.848,-0.11],[3.859,-0.047],[3.869,-0.047],[3.874,-0.105],[3.89,-0.058],[3.874,0],[3.675,0],[3.659,-0.026],[3.67,-0.037],[3.659,-0.11],[3.623,-0.126],[3.497,-0.115],[3.486,0],[3.277,0],[3.261,-0.11],[3.245,-0.126],[3.067,-0.115],[3.104,-0.1],[3.104,-0.016],[3.088,0],[2.878,0],[2.873,-0.11],[2.826,-0.126],[2.805,-0.115],[2.721,-0.126],[2.705,-0.11],[2.716,-0.026],[2.7,0],[2.49,0],[2.475,-0.026],[2.475,-0.11],[2.448,-0.126],[2.333,-0.115],[2.312,0],[2.092,0],[2.071,-0.115],[1.935,-0.115],[1.924,0],[1.704,0],[1.688,-0.016],[1.683,-0.115],[1.557,-0.115],[1.536,0],[1.305,0],[1.284,-0.115],[1.159,-0.115],[1.153,-0.016],[1.138,0],[0.907,0],[0.886,-0.115],[0.781,-0.115],[0.76,0],[0.519,0],[0.503,-0.026],[0.503,-0.1],[0.488,-0.115],[0.309,-0.115],[0.294,-0.131],[0.304,-0.404],[0.288,-0.419],[0.173,-0.419],[0.079,-0.44],[0.052,-0.467]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"x":"rear_x","y":"rail_top_above_bore"}}},"bounds":{"min":[-0.763,-0.9265,-0.75],"max":[8.831,1.2125,0.75]},"volume_in3":3.9687,"centroid":[3.5177,0.2345,0],"shell":[3.876,0.2107,0],"area_in2":90.3816,"triangles":41434,"manifold":true,"slabs":[[-0.763,-0.906,-0.75,-0.363,1.094,0.75],[-0.363,-0.927,-0.75,1.236,1.212,0.75],[1.236,-0.834,-0.75,2.435,1.212,0.75],[2.435,-0.738,-0.75,8.831,1.212,0.75]],"slots":["body"]},"aero-s-one-15-handguard":{"part":"aero-s-one-15-handguard","model":"aero-s-one-15-handguard.glb","script":"aero_s_one_15_handguard.py","inputs":{"aero-mid-gas-tube.od":0.18,"aero-s-one-15-handguard.bottom_flat_width":0.609,"aero-s-one-15-handguard.height":1.95,"aero-s-one-15-handguard.inside_diameter":1.3,"aero-s-one-15-handguard.inside_height":1.65,"aero-s-one-15-handguard.lower_edge_below_rail_top":1.759,"aero-s-one-15-handguard.lower_edge_width":1.133,"aero-s-one-15-handguard.mlok_row_below_rail_top":1.17,"aero-s-one-15-handguard.mlok_slot0_x":4.127,"aero-s-one-15-handguard.mlok_slots":7,"aero-s-one-15-handguard.qd_socket_d":0.35,"aero-s-one-15-handguard.qd_socket_from_rail_slot0":1.853,"aero-s-one-15-handguard.rail_block_front_flat_start_from_slot0":12.72,"aero-s-one-15-handguard.rail_block_rear_flat_end_from_slot0":1.46,"aero-s-one-15-handguard.rail_bridge_recess":0.03,"aero-s-one-15-handguard.rail_centre_gap":0.4,"aero-s-one-15-handguard.rail_front_from_rear":15.321,"aero-s-one-15-handguard.rail_front_slot0_x":13.056,"aero-s-one-15-handguard.rail_front_slots":4,"aero-s-one-15-handguard.rail_neck_foot_below_rail_top":0.38,"aero-s-one-15-handguard.rail_neck_width":0.594,"aero-s-one-15-handguard.rail_ramp_front_foot_from_slot0":12.27,"aero-s-one-15-handguard.rail_ramp_rear_foot_from_slot0":1.95,"aero-s-one-15-handguard.rail_rear_face_from_rear":0.296,"aero-s-one-15-handguard.rail_rear_slots":4,"aero-s-one-15-handguard.rail_slot0_x":0.054,"aero-s-one-15-handguard.rail_top_above_bore":1.2125,"aero-s-one-15-handguard.rail_window_length":0.54,"aero-s-one-15-handguard.rear_x":-0.766,"aero-s-one-15-handguard.rib_count":9,"aero-s-one-15-handguard.rib_height":0.03,"aero-s-one-15-handguard.rib_length":0.15,"aero-s-one-15-handguard.short_slot_centre_from_rail_slot0":2.888,"aero-s-one-15-handguard.short_slot_length":0.39,"aero-s-one-15-handguard.side_flat_bottom_below_rail_top":1.51,"aero-s-one-15-handguard.side_flat_top_below_rail_top":0.885,"aero-s-one-15-handguard.side_top_width":1.455,"aero-s-one-15-handguard.spine_below_rail_top":0.242,"aero-s-one-15-handguard.spine_roof_below_rail_top":0.2922,"aero-s-one-15-handguard.thin_slot_count":12,"aero-s-one-15-handguard.thin_slot_first_from_rail_slot0":2.168,"aero-s-one-15-handguard.thin_slot_length":0.93,"aero-s-one-15-handguard.thin_slot_pitch":1.0664,"aero-s-one-15-handguard.thin_slot_row_a_y":0.71,"aero-s-one-15-handguard.thin_slot_row_b_y":0.46,"aero-s-one-15-handguard.thin_slot_row_d_y":-0.41,"aero-s-one-15-handguard.thin_slot_row_e_y":-0.635,"aero-s-one-15-handguard.thin_slot_width":0.22,"aero-s-one-15-handguard.width":1.5,"std.ar15.gas_tube_above_bore":0.78,"std.mlok.slot_corner_r":0.0937007874015748,"std.mlok.slot_length":1.2598425196850394,"std.mlok.slot_pitch":1.574803149606299,"std.mlok.slot_width":0.2755905511811024,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{"side":[[0,-0.806],[0,-1.592],[0.013,-1.606],[0.027,-1.792],[0.047,-1.812],[0.113,-1.812],[0.127,-1.825],[0.22,-1.825],[0.233,-1.839],[0.26,-1.825],[0.3,-1.852],[0.32,-1.872],[0.333,-2.072],[0.353,-2.119],[0.74,-2.119],[0.753,-2.132],[1.073,-2.132],[1.093,-2.112],[1.066,-2.085],[1.146,-2.005],[1.113,-1.972],[1.059,-1.959],[1.033,-1.959],[1.006,-1.999],[0.999,-1.952],[0.959,-1.912],[1.013,-1.885],[1.013,-1.832],[1.059,-1.772],[1.392,-1.772],[1.466,-1.819],[1.492,-1.899],[1.372,-2.099],[1.379,-2.132],[1.632,-2.132],[1.899,-2.065],[2.139,-2.039],[2.285,-1.999],[2.925,-1.999],[3.071,-1.959],[15.29,-1.959],[15.31,-1.939],[15.31,-1.885],[15.323,-1.872],[15.337,-1.619],[15.35,-1.606],[15.35,-0.806],[15.337,-0.793],[15.323,-0.433],[15.31,-0.42],[15.323,-0.02],[15.263,0],[15.21,0],[15.197,-0.013],[15.183,0],[15.157,-0.013],[15.103,0],[15.084,-0.02],[15.084,-0.113],[15.05,-0.133],[15.01,-0.12],[14.957,-0.133],[14.924,-0.1],[14.924,-0.02],[14.85,0],[14.717,0],[14.697,-0.02],[14.684,-0.113],[14.597,-0.133],[14.557,-0.133],[14.524,-0.1],[14.517,-0.013],[14.464,-0.013],[14.451,0],[14.317,0],[14.297,-0.033],[14.297,-0.113],[14.237,-0.133],[14.157,-0.133],[14.124,-0.073],[14.124,-0.02],[14.064,0],[13.931,0],[13.911,-0.02],[13.911,-0.113],[13.824,-0.12],[13.811,-0.133],[13.758,-0.133],[13.738,-0.113],[13.731,-0.013],[13.678,0],[13.664,-0.013],[13.518,-0.013],[13.331,-0.16],[13.131,-0.24],[12.145,-0.24],[12.092,-0.213],[12.012,-0.213],[11.972,-0.24],[11.079,-0.24],[11.026,-0.213],[10.96,-0.213],[10.906,-0.24],[10.013,-0.24],[9.96,-0.213],[9.894,-0.213],[9.84,-0.24],[8.934,-0.24],[8.894,-0.213],[8.828,-0.213],[8.774,-0.24],[7.868,-0.24],[7.815,-0.213],[7.762,-0.213],[7.708,-0.24],[6.802,-0.24],[6.762,-0.213],[6.682,-0.213],[6.642,-0.24],[5.736,-0.24],[5.696,-0.213],[5.616,-0.213],[5.563,-0.24],[4.67,-0.24],[4.63,-0.213],[4.537,-0.213],[4.497,-0.24],[3.604,-0.24],[3.551,-0.213],[3.471,-0.213],[3.431,-0.24],[2.712,-0.24],[2.498,-0.16],[2.338,-0.04],[2.259,0],[2.099,0],[2.092,-0.087],[2.072,-0.12],[1.925,-0.12],[1.919,-0.02],[1.899,0],[1.712,0],[1.692,-0.02],[1.692,-0.073],[1.672,-0.12],[1.526,-0.12],[1.506,-0.047],[1.512,0],[1.312,0],[1.292,-0.02],[1.292,-0.1],[1.273,-0.12],[1.139,-0.12],[1.119,-0.1],[1.113,0],[0.913,0],[0.893,-0.02],[0.893,-0.1],[0.873,-0.12],[0.74,-0.12],[0.713,0],[0.513,0],[0.493,-0.02],[0.493,-0.1],[0.473,-0.12],[0.3,-0.12],[0.28,-0.14],[0.293,-0.153],[0.293,-0.393],[0.273,-0.413],[0.087,-0.426],[0.04,-0.46],[0.027,-0.606],[0.013,-0.62],[0.013,-0.793]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"x":"rear_x","y":"rail_top_above_bore"}}},"bounds":{"min":[-0.766,-0.9195,-0.75],"max":[14.584,1.2125,0.75]},"volume_in3":5.1593,"centroid":[6.1124,0.1409,0],"shell":[6.6672,0.1502,0],"area_in2":132.9429,"triangles":55028,"manifold":true,"slabs":[[-0.766,-0.906,-0.75,-0.372,1.094,0.75],[-0.372,-0.919,-0.75,1.202,1.212,0.75],[1.202,-0.845,-0.75,1.596,1.212,0.75],[1.596,-0.738,-0.75,1.989,1.155,0.75],[1.989,-0.738,-0.75,12.222,1,0.75],[12.222,-0.738,-0.75,12.616,1.093,0.75],[12.616,-0.738,-0.75,14.584,1.212,0.75]],"slots":["body"]},"aimpoint-duty-rds-30mm-mount":{"part":"aimpoint-duty-rds-30mm-mount","model":"aimpoint-duty-rds-30mm-mount.glb","script":"aimpoint_duty_rds.py","inputs":{"aimpoint-duty-rds-30mm-mount.deck_above_rail":0.152,"aimpoint-duty-rds-39mm-mount.deck_above_rail":0.5064,"aimpoint-duty-rds-39mm-mount.deck_x":0,"aimpoint-duty-rds.adjuster_proud":0.01,"aimpoint-duty-rds.battery_cap_below_axis":0.083,"aimpoint-duty-rds.battery_cap_from_front":1.16,"aimpoint-duty-rds.battery_cap_od":1.202,"aimpoint-duty-rds.cap_slot_depth":0.04,"aimpoint-duty-rds.cap_slot_length":0.65,"aimpoint-duty-rds.cap_slot_width":0.11,"aimpoint-duty-rds.clamp_bottom_y":-0.4,"aimpoint-duty-rds.groove_bottom_above_clamp_bottom":0.49,"aimpoint-duty-rds.groove_depth":0.03,"aimpoint-duty-rds.groove_top_above_clamp_bottom":0.811,"aimpoint-duty-rds.height":2.637795275590551,"aimpoint-duty-rds.jaw_top_above_clamp_bottom":0.502,"aimpoint-duty-rds.keypad_recess":0.02,"aimpoint-duty-rds.lock_screw_proud":0.04,"aimpoint-duty-rds.mount_length":2.045,"aimpoint-duty-rds.optical_axis_above_rail":1.5354330708661417,"aimpoint-duty-rds.shoulder_radius":0.2,"aimpoint-duty-rds.tube_od":1.32,"aimpoint-duty-rds.underside_above_clamp_bottom":0.906,"aimpoint-duty-rds.width":1.4566929133858268,"aimpoint-duty-rds.windage_below_axis":0.077,"aimpoint-duty-rds.windage_from_front":2.083,"aimpoint-duty-rds.windage_od":0.497,"aimpoint-duty-rds.window_d":0.7086614173228346,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{},"features":{},"placement":{},"bounds":{"min":[-1.026,-0.4,-0.7],"max":[1.0236,0.152,0.66]},"volume_in3":0.8188,"centroid":[-0.0029,-0.0553,-0.0038],"shell":[-0.0036,-0.0681,-0.0775],"area_in2":11.6861,"triangles":2168,"manifold":true,"rail_seat":{"x":[-1.0225,1.0225],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-1.026,-0.4,-0.7,1.024,0.152,0.66]],"slots":["mount"]},"aimpoint-duty-rds-39mm-mount":{"part":"aimpoint-duty-rds-39mm-mount","model":"aimpoint-duty-rds-39mm-mount.glb","script":"aimpoint_duty_rds.py","inputs":{"aimpoint-duty-rds-39mm-mount.deck_above_rail":0.5064,"aimpoint-duty-rds-39mm-mount.deck_x":0,"aimpoint-duty-rds.adjuster_proud":0.01,"aimpoint-duty-rds.battery_cap_below_axis":0.083,"aimpoint-duty-rds.battery_cap_from_front":1.16,"aimpoint-duty-rds.battery_cap_od":1.202,"aimpoint-duty-rds.cap_slot_depth":0.04,"aimpoint-duty-rds.cap_slot_length":0.65,"aimpoint-duty-rds.cap_slot_width":0.11,"aimpoint-duty-rds.clamp_bottom_y":-0.4,"aimpoint-duty-rds.groove_bottom_above_clamp_bottom":0.49,"aimpoint-duty-rds.groove_depth":0.03,"aimpoint-duty-rds.groove_top_above_clamp_bottom":0.811,"aimpoint-duty-rds.height":2.637795275590551,"aimpoint-duty-rds.jaw_top_above_clamp_bottom":0.502,"aimpoint-duty-rds.keypad_recess":0.02,"aimpoint-duty-rds.lock_screw_proud":0.04,"aimpoint-duty-rds.mount_length":2.045,"aimpoint-duty-rds.optical_axis_above_rail":1.5354330708661417,"aimpoint-duty-rds.shoulder_radius":0.2,"aimpoint-duty-rds.tube_od":1.32,"aimpoint-duty-rds.underside_above_clamp_bottom":0.906,"aimpoint-duty-rds.width":1.4566929133858268,"aimpoint-duty-rds.windage_below_axis":0.077,"aimpoint-duty-rds.windage_from_front":2.083,"aimpoint-duty-rds.windage_od":0.497,"aimpoint-duty-rds.window_d":0.7086614173228346,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{},"features":{},"placement":{},"bounds":{"min":[-1.026,-0.4,-0.7],"max":[1.026,0.506,0.66]},"volume_in3":1.7555,"centroid":[-0.0007,0.1506,-0.009],"shell":[-0.0029,0.0681,-0.0606],"area_in2":14.1626,"triangles":2292,"manifold":true,"rail_seat":{"x":[-1.0225,1.0225],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-1.026,-0.4,-0.7,1.026,0.506,0.66]],"slots":["mount"]},"aimpoint-duty-rds":{"part":"aimpoint-duty-rds","model":"aimpoint-duty-rds.glb","script":"aimpoint_duty_rds.py","inputs":{"aimpoint-duty-rds-39mm-mount.deck_above_rail":0.5064,"aimpoint-duty-rds-39mm-mount.deck_x":0,"aimpoint-duty-rds.adjuster_proud":0.01,"aimpoint-duty-rds.battery_cap_below_axis":0.083,"aimpoint-duty-rds.battery_cap_from_front":1.16,"aimpoint-duty-rds.battery_cap_od":1.202,"aimpoint-duty-rds.cap_slot_depth":0.04,"aimpoint-duty-rds.cap_slot_length":0.65,"aimpoint-duty-rds.cap_slot_width":0.11,"aimpoint-duty-rds.clamp_bottom_y":-0.4,"aimpoint-duty-rds.groove_bottom_above_clamp_bottom":0.49,"aimpoint-duty-rds.groove_depth":0.03,"aimpoint-duty-rds.groove_top_above_clamp_bottom":0.811,"aimpoint-duty-rds.height":2.637795275590551,"aimpoint-duty-rds.jaw_top_above_clamp_bottom":0.502,"aimpoint-duty-rds.keypad_recess":0.02,"aimpoint-duty-rds.lock_screw_proud":0.04,"aimpoint-duty-rds.mount_length":2.045,"aimpoint-duty-rds.optical_axis_above_rail":1.5354330708661417,"aimpoint-duty-rds.shoulder_radius":0.2,"aimpoint-duty-rds.tube_od":1.32,"aimpoint-duty-rds.underside_above_clamp_bottom":0.906,"aimpoint-duty-rds.width":1.4566929133858268,"aimpoint-duty-rds.windage_below_axis":0.077,"aimpoint-duty-rds.windage_from_front":2.083,"aimpoint-duty-rds.windage_od":0.497,"aimpoint-duty-rds.window_d":0.7086614173228346,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{"side":[[-1.577,1.977],[-1.571,1.672],[-1.549,1.498],[-1.53,1.447],[-1.506,1.424],[-1.484,1.42],[-1.455,1.401],[-1.43,1.401],[-1.404,1.417],[-1.385,1.417],[-1.357,1.379],[-1.341,1.376],[-1.17,1.37],[-1.154,1.382],[-1.141,1.37],[-1.122,1.37],[-0.978,1.235],[-0.978,1.187],[-1.016,1.146],[-1.026,1.118],[-1.019,1.067],[-1.026,0.309],[-1.013,0.284],[-1.007,0.243],[-1.007,0.033],[-0.989,0.006],[-0.33,0.003],[-0.314,0.016],[0.314,0.016],[0.33,0.003],[0.615,0],[0.957,0],[0.984,0.024],[0.988,0.233],[0.997,0.281],[1.019,0.303],[1.022,0.334],[1.026,0.883],[1.003,0.943],[1.003,1.114],[0.973,1.148],[0.907,1.154],[0.886,1.181],[0.886,1.206],[0.919,1.246],[0.996,1.306],[1.03,1.275],[1.268,1.275],[1.292,1.292],[1.306,1.316],[1.325,1.316],[1.347,1.3],[1.37,1.297],[1.408,1.319],[1.436,1.325],[1.473,1.384],[1.492,1.466],[1.52,1.758],[1.52,2.094],[1.504,2.316],[1.469,2.484],[1.46,2.503],[1.43,2.53],[1.328,2.53],[1.322,2.536],[1.027,2.533],[1.005,2.53],[0.996,2.514],[0.97,2.514],[0.323,2.59],[0.184,2.584],[-0.006,2.559],[-0.124,2.552],[-0.187,2.571],[-0.304,2.622],[-0.897,2.638],[-0.954,2.638],[-0.989,2.628],[-0.999,2.638],[-1.148,2.486],[-1.512,2.438],[-1.539,2.389],[-1.558,2.287]]},"features":{"side":{"front_cover_ring":[[[1.519,2.535],[1.068,2.535],[1.068,1.305],[1.519,1.305]]],"rear_cover_ring":[[[-1.167,2.497],[-1.576,2.497],[-1.576,1.324],[-1.167,1.324]]],"keypad":[[[0.774,1.679],[0.019,1.679],[0.019,0.927],[0.774,0.927]]],"keypad_button":[[[0.675,1.577],[0.117,1.577],[0.117,1.026],[0.675,1.026]]],"locking_bar":[[[0.418,0.503],[-0.438,0.503],[-0.438,0.014],[0.418,0.014]]],"lock_screw":[[[0.155,0.407],[-0.168,0.407],[-0.168,0.084],[0.155,0.084]]],"foot_seam":[[[1.021,0.911],[-1.024,0.911],[-1.024,0.899],[1.021,0.899]]],"jaw_top":[[[1.021,0.509],[-1.024,0.509],[-1.024,0.496],[1.021,0.496]]],"front_lid":[[[1.037,2.513],[-0.016,3.163],[0.041,3.492],[1.094,2.842]]],"rear_lid":[[[-1.008,2.636],[-1.221,2.833],[-0.764,3.705],[-0.548,3.521]]],"front_hinge":[[[1.433,2.535],[1.43,2.674],[1.385,2.763],[1.309,2.811],[1.202,2.792],[1.068,2.617],[1.037,2.516],[1.037,2.389],[1.433,2.389]]],"rear_hinge":[[[-1.135,2.494],[-1.183,2.662],[-1.246,2.741],[-1.373,2.738],[-1.443,2.662],[-1.5,2.547],[-1.515,2.446],[-1.515,2.357],[-1.135,2.357]]]}},"placement":{"side":{"plane":"xy","offset":{"y":"clamp_bottom_y"}}},"bounds":{"min":[-1.581,-0.0004,-0.7283],"max":[1.524,2.7728,0.7283]},"axis_y":1.029,"volume_in3":6.4792,"centroid":[0.0118,1.0051,0.0072],"shell":[0.0026,1.1536,0.034],"area_in2":39.5279,"triangles":25512,"manifold":true,"slabs":[[-1.581,0.464,-0.565,-1.193,1.989,0.565],[-1.193,0,-0.66,-0.417,2.773,0.67],[-0.417,0,-0.66,-0.028,2.355,0.728],[-0.028,0,-0.728,0.36,2.563,0.728],[0.36,0,-0.728,0.748,2.403,0.728],[0.748,0,-0.728,1.136,2.163,0.728],[1.136,0.369,-0.66,1.524,1.924,0.66]],"slots":["body","cap","buttons","adjusters","covers","lens"]},"aimpoint-micro-lrp-39mm":{"part":"aimpoint-micro-lrp-39mm","model":"aimpoint-micro-lrp-39mm.glb","script":"aimpoint_micro_t_2.py","inputs":{"aimpoint-micro-lrp-39mm.deck_above_rail":0.9464,"aimpoint-micro-lrp-39mm.deck_x":0,"aimpoint-micro-t-2.base_top_above_clamp_bottom":0.59,"aimpoint-micro-t-2.clamp_bottom_y":-0.392,"aimpoint-micro-t-2.cross_bolt_below_axis":1.573,"aimpoint-micro-t-2.cross_bolt_from_front":1.478,"aimpoint-micro-t-2.cross_bolt_socket_od":0.175,"aimpoint-micro-t-2.height":2.739,"aimpoint-micro-t-2.intensity_below_axis":0.068,"aimpoint-micro-t-2.intensity_from_front":1.125,"aimpoint-micro-t-2.intensity_od":1.082,"aimpoint-micro-t-2.mount_length":2.036,"aimpoint-micro-t-2.optical_axis_above_rail":1.5354330708661417,"aimpoint-micro-t-2.shoulder_radius":0.26,"aimpoint-micro-t-2.spacer_length":1.922,"aimpoint-micro-t-2.tube_od":1.218,"aimpoint-micro-t-2.underside_above_clamp_bottom":1.338,"aimpoint-micro-t-2.width":1.6141732283464567,"aimpoint-micro-t-2.windage_below_axis":0.053,"aimpoint-micro-t-2.windage_from_front":1.994,"aimpoint-micro-t-2.windage_od":0.541,"aimpoint-micro-t-2.window_d":0.7086614173228346,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.top_width":0.835},"profiles":{},"features":{},"placement":{},"bounds":{"min":[-1.351,-0.392,-0.6969],"max":[1.088,0.948,0.5894]},"volume_in3":2.5158,"centroid":[-0.0061,0.3817,-0.0148],"shell":[-0.0257,0.2317,-0.047],"area_in2":20.167,"triangles":2144,"manifold":true,"rail_seat":{"x":[-1.018,1.018],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-1.351,-0.374,-0.697,-1.003,0.142,0.589],[-1.003,-0.392,-0.697,1.088,0.948,0.589]],"slots":["mount","hardware"]},"aimpoint-micro-t-2":{"part":"aimpoint-micro-t-2","model":"aimpoint-micro-t-2.glb","script":"aimpoint_micro_t_2.py","inputs":{"aimpoint-micro-lrp-39mm.deck_above_rail":0.9464,"aimpoint-micro-lrp-39mm.deck_x":0,"aimpoint-micro-t-2.base_top_above_clamp_bottom":0.59,"aimpoint-micro-t-2.clamp_bottom_y":-0.392,"aimpoint-micro-t-2.cross_bolt_below_axis":1.573,"aimpoint-micro-t-2.cross_bolt_from_front":1.478,"aimpoint-micro-t-2.cross_bolt_socket_od":0.175,"aimpoint-micro-t-2.height":2.739,"aimpoint-micro-t-2.intensity_below_axis":0.068,"aimpoint-micro-t-2.intensity_from_front":1.125,"aimpoint-micro-t-2.intensity_od":1.082,"aimpoint-micro-t-2.mount_length":2.036,"aimpoint-micro-t-2.optical_axis_above_rail":1.5354330708661417,"aimpoint-micro-t-2.shoulder_radius":0.26,"aimpoint-micro-t-2.spacer_length":1.922,"aimpoint-micro-t-2.tube_od":1.218,"aimpoint-micro-t-2.underside_above_clamp_bottom":1.338,"aimpoint-micro-t-2.width":1.6141732283464567,"aimpoint-micro-t-2.windage_below_axis":0.053,"aimpoint-micro-t-2.windage_from_front":1.994,"aimpoint-micro-t-2.windage_od":0.541,"aimpoint-micro-t-2.window_d":0.7086614173228346,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.top_width":0.835},"profiles":{"side":[[-1.399,2.058],[-1.394,1.706],[-1.378,1.563],[-1.355,1.484],[-1.339,1.465],[-1.313,1.462],[-1.283,1.442],[-1.219,1.46],[-1.188,1.419],[-1.02,1.414],[-1.004,1.422],[-0.979,1.409],[-0.965,1.387],[-0.96,1.311],[-0.957,0.601],[-0.98,0.581],[-1.006,0.527],[-1.008,0.392],[-1.015,0.385],[-1.045,0.385],[-1.277,0.398],[-1.336,0.383],[-1.353,0.356],[-1.35,0.063],[-1.321,0.048],[-1.295,0.051],[-1.198,0.11],[-1.145,0.105],[-1.03,0.11],[-1.023,0.103],[-1.018,0.032],[-1.004,0.018],[-0.961,0.003],[-0.264,0],[-0.001,0],[0.198,0.003],[0.318,0.02],[0.992,0.015],[1.023,0.029],[1.029,0.119],[1.016,0.175],[1.092,0.315],[1.097,0.341],[1.023,0.463],[1.018,0.502],[0.988,0.573],[0.955,0.596],[0.962,0.767],[0.965,1.359],[0.974,1.371],[0.99,1.331],[1.007,1.317],[1.229,1.32],[1.251,1.336],[1.265,1.36],[1.283,1.36],[1.311,1.342],[1.331,1.342],[1.359,1.363],[1.382,1.365],[1.414,1.408],[1.437,1.515],[1.457,1.841],[1.452,2.158],[1.437,2.344],[1.411,2.457],[1.396,2.487],[1.374,2.504],[1.27,2.504],[1.247,2.522],[1.226,2.522],[1.219,2.555],[0.963,2.555],[0.962,2.508],[0.98,2.497],[0.978,2.477],[0.966,2.468],[0.195,2.537],[0.101,2.552],[0.034,2.58],[-0.162,2.733],[-0.287,2.733],[-0.318,2.716],[-0.359,2.726],[-0.456,2.728],[-0.47,2.722],[-0.479,2.703],[-0.542,2.703],[-0.56,2.728],[-0.657,2.728],[-0.703,2.718],[-0.718,2.728],[-0.731,2.723],[-0.749,2.736],[-0.859,2.739],[-1.002,2.46],[-1.226,2.46],[-1.225,2.431],[-1.231,2.425],[-1.321,2.425],[-1.35,2.406],[-1.365,2.375],[-1.383,2.283]]},"features":{"side":{"elevation_turret":[[[-0.336,2.712],[-0.706,2.712],[-0.706,2.49],[-0.336,2.49]]],"turret_recess":[[[-0.328,2.719],[-0.724,2.719],[-0.724,2.49],[-0.328,2.49]]],"lever_bar":[[[0.558,0.364],[-0.872,0.364],[-0.872,0.149],[0.558,0.149]]],"lever_grip":[[[-0.846,0.371],[-1.351,0.371],[-1.351,0.06],[-0.846,0.06]]],"lever_nut":[[[1.086,0.453],[0.838,0.453],[0.838,0.162],[1.086,0.162]]],"front_cover_ring":[[[1.456,2.556],[0.992,2.556],[0.992,1.318],[1.456,1.318]]],"rear_cover_ring":[[[-1.038,2.462],[-1.397,2.462],[-1.397,1.415],[-1.038,1.415]]],"front_lid":[[[0.941,2.487],[-0.019,3.12],[0.144,3.37],[1.104,2.737]]],"rear_lid":[[[-0.831,2.732],[-1.124,2.732],[-0.989,3.712],[-0.695,3.712]]],"front_hinge":[[[1.374,2.564],[1.38,2.605],[1.385,2.653],[1.349,2.704],[1.293,2.755],[1.201,2.776],[1.127,2.758],[1.094,2.727],[0.981,2.556],[0.981,2.4],[1.221,2.4],[1.221,2.556]]],"rear_hinge":[[[-0.872,2.727],[-1.124,2.727],[-1.157,2.691],[-1.254,2.681],[-1.3,2.64],[-1.334,2.574],[-1.326,2.528],[-1.288,2.492],[-1.244,2.462],[-1.244,2.311],[-1.038,2.311],[-0.999,2.462],[-0.928,2.605]]]}},"placement":{"side":{"plane":"xy","offset":{"y":"clamp_bottom_y"}}},"bounds":{"min":[-1.403,-0.0214,-0.6104],"max":[1.461,2.3937,1.0247]},"axis_y":0.589,"volume_in3":4.7599,"centroid":[0.0429,0.7386,0.0774],"shell":[0.0184,0.8299,0.0996],"area_in2":32.6177,"triangles":24518,"manifold":true,"slabs":[[-1.403,0.076,-0.513,-1.045,1.977,0.513],[-1.045,0,-0.589,-0.687,2.394,0.807],[-0.687,0,-0.589,-0.329,1.374,0.807],[-0.329,0,-0.589,0.029,1.856,1.025],[0.029,-0.02,-0.589,0.387,2.031,1.025],[0.387,-0.017,-0.589,0.745,1.871,1.025],[0.745,-0.021,-0.61,1.103,1.635,1.025],[1.103,-0.02,-0.609,1.461,1.438,0.609]],"slots":["body","knobs","covers","lens"]},"aimpoint-pro":{"part":"aimpoint-pro","model":"aimpoint-pro.glb","script":"aimpoint_pro.py","inputs":{"aimpoint-pro.axis_above_knob_bottom":2.28,"aimpoint-pro.battery_od":0.717,"aimpoint-pro.knob_bottom_y":-0.7446,"aimpoint-pro.lid_thickness":0.12,"aimpoint-pro.mount_length":2.771,"aimpoint-pro.mount_width":1.1,"aimpoint-pro.optical_axis_above_rail":1.5354330708661417,"aimpoint-pro.qrp2_right_inboard":0.5906,"aimpoint-pro.right_jaw_below_holes":0.729,"aimpoint-pro.ring_ear_reach":0.24,"aimpoint-pro.rotary_switch_length":0.494,"aimpoint-pro.sight_width":1.9291338582677164,"aimpoint-pro.tube_od":1.1811023622047243,"aimpoint-pro.width":2.7559055118110236,"aimpoint-pro.windage_behind_mount_middle":0.639,"aimpoint-pro.windage_below_axis":0.08,"aimpoint-pro.windage_od":0.805,"aimpoint-pro.window_d":0.905511811023622,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{"side":[[-2.1,2.43],[-2.1,2.152],[-2.083,1.867],[-2.068,1.781],[-2.033,1.681],[-2.017,1.665],[-1.995,1.662],[-1.956,1.637],[-1.931,1.637],[-1.917,1.651],[-1.895,1.655],[-1.86,1.608],[-1.831,1.598],[-1.681,1.587],[-1.631,1.587],[-1.578,1.598],[-1.421,1.551],[-1.289,1.551],[-1.273,1.528],[-1.289,1.516],[-1.321,1.516],[-1.337,1.503],[-1.387,1.432],[-1.394,1.403],[-1.387,1.336],[-1.391,1.25],[-1.384,1.236],[-1.384,1.057],[-1.391,1.022],[-1.391,0.986],[-1.384,0.975],[-1.387,0.704],[-1.371,0.688],[-1.339,0.688],[-1.33,0.679],[-1.337,0.597],[-1.325,0.585],[-1.232,0.585],[-0.608,0.599],[-0.599,0.59],[-0.592,0.415],[-0.587,0.41],[-0.462,0.41],[-0.453,0.401],[-0.442,0.348],[-0.41,0.28],[-0.407,0.251],[-0.378,0.223],[-0.337,0.157],[-0.266,0.093],[-0.209,0.068],[-0.184,0.046],[-0.073,0.011],[-0.002,0.004],[0.009,0],[0.087,0.007],[0.173,0.029],[0.262,0.071],[0.326,0.121],[0.374,0.169],[0.424,0.237],[0.471,0.351],[0.474,0.398],[0.487,0.41],[0.594,0.41],[0.61,0.419],[0.613,0.579],[0.622,0.588],[1.229,0.592],[1.311,0.596],[1.319,0.604],[1.316,0.686],[1.325,0.695],[1.378,0.699],[1.387,0.744],[1.377,1.243],[1.384,1.257],[1.394,1.664],[1.398,1.689],[1.407,1.697],[1.45,1.69],[1.724,1.541],[2.092,1.541],[2.118,1.5],[2.195,1.434],[2.723,1.444],[2.776,1.494],[2.83,1.487],[2.901,1.519],[2.938,1.564],[2.963,1.617],[2.996,1.738],[3.021,1.895],[3.042,2.223],[3.031,2.569],[2.999,2.808],[2.967,2.937],[2.931,3.004],[2.905,3.038],[2.109,3.042],[2.092,3.021],[1.742,3.024],[1.692,3.01],[1.5,2.903],[1.457,2.899],[1.4,2.899],[1.391,2.908],[1.377,2.969],[1.364,2.978],[1.325,2.981],[0.451,2.981],[0.442,2.99],[0.442,3.261],[0.432,3.35],[0.417,3.39],[0.39,3.416],[0.362,3.423],[0.219,3.423],[0.205,3.388],[0.177,3.391],[0.162,3.406],[-0.947,3.409],[-0.954,3.423],[-1.328,3.416],[-1.33,2.919],[-1.339,2.91],[-2.02,2.91],[-2.047,2.873],[-2.072,2.776],[-2.09,2.623]]},"features":{"side":{"front_ring":[[[3.037,3.04],[2.127,3.04],[2.127,1.435],[3.037,1.435]]],"bell":[[[2.127,3.012],[1.385,3.012],[1.385,1.471],[2.127,1.471]]],"ring":[[[1.385,2.983],[0.216,2.983],[0.216,1.492],[1.385,1.492]]],"ring_split":[[[1.385,2.398],[0.216,2.398],[0.216,2.22],[1.385,2.22]]],"ring_ears":[[[1.385,2.484],[0.216,2.484],[0.216,2.398],[1.385,2.398]]],"ring_screws":[[[1.253,2.634],[1.04,2.634],[1.04,2.477],[1.253,2.477]],[[0.647,2.634],[0.433,2.634],[0.433,2.477],[0.647,2.477]]],"body":[[[0.216,3.012],[-1.375,3.012],[-1.375,1.514],[0.216,1.514]]],"battery":[[[0.612,3.422],[-1.671,3.422],[-1.671,3.004],[0.612,3.004]]],"battery_cap":[[[0.612,3.422],[0.373,3.422],[0.373,3.004],[0.612,3.004]]],"elevation_cap":[[[-0.173,3.368],[-0.94,3.368],[-0.94,3.09],[-0.173,3.09]]],"rear_ring":[[[-1.671,2.912],[-2.099,2.912],[-2.099,1.557],[-1.671,1.557]]],"foot":[[[1.385,1.496],[-1.389,1.496],[-1.389,1.321],[1.385,1.321]]],"spacer":[[[1.385,1.321],[-1.389,1.321],[-1.389,0.979],[1.385,0.979]]],"holes":[[[1.043,1.236],[-0.683,1.236],[-0.683,1.079],[1.043,1.079]]],"qrp2":[[[1.385,0.979],[-1.389,0.979],[-1.389,0.686],[1.385,0.686]]],"lip":[[[1.314,0.686],[-1.332,0.686],[-1.332,0.59],[1.314,0.59]]],"jaw":[[[0.612,0.686],[-0.601,0.686],[-0.601,0.408],[0.612,0.408]]],"knob":[[[0.487,0.95],[-0.458,0.95],[-0.458,0.002],[0.487,0.002]]],"front_lid":[[[2.395,3.029],[0.79,3.867],[0.95,4.099],[2.555,3.261]]],"rear_lid":[[[-1.1,3.361],[-1.35,3.411],[-0.637,4.349],[-0.369,4.231]]],"front_hinge":[[[2.93,3.029],[2.905,3.243],[2.769,3.397],[2.573,3.404],[2.43,3.34],[2.27,3.101],[2.27,3.029]]],"rear_hinge":[[[-1.332,2.905],[-1.332,3.397],[-1.564,3.397],[-1.742,3.29],[-1.849,3.101],[-1.831,2.905]]]}},"placement":{"side":{"plane":"xy","offset":{"y":"knob_bottom_y"}}},"bounds":{"min":[-2.104,-0.7426,-1.5758],"max":[3.046,3.5904,1.1801]},"axis_y":1.5354,"volume_in3":15.0746,"centroid":[0.3387,1.3341,0.031],"shell":[0.2916,1.2838,0.038],"area_in2":109.9161,"triangles":45176,"manifold":true,"rail_seat":{"x":[-1.389,1.385],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-2.104,0.844,-0.691,-1.708,2.566,0.691],[-1.708,-0.316,-0.749,-1.312,2.678,1.18],[-1.312,-0.316,-0.749,-0.916,3.125,1.18],[-0.916,-0.337,-0.749,-0.519,3.59,1.18],[-0.519,-0.722,-1.576,-0.123,3.558,1.18],[-0.123,-0.743,-1.576,0.273,2.678,1.18],[0.273,-0.666,-1.576,0.669,2.678,1.18],[0.669,-0.316,-0.943,1.065,3.291,0.943],[1.065,-0.316,-0.943,1.461,3.204,0.943],[1.461,0.796,-0.905,1.858,2.997,0.905],[1.858,0.69,-0.888,2.254,2.79,0.888],[2.254,0.69,-0.845,3.046,2.659,0.845]],"slots":["body","knobs","mount","covers","lens"]},"armaspec-stealth-recoil-spring-gen4-c":{"part":"armaspec-stealth-recoil-spring-gen4-c","model":"armaspec-stealth-recoil-spring-gen4-c.glb","script":"armaspec_stealth_recoil_spring_gen4.py","inputs":{"armaspec-stealth-recoil-spring-gen4-c.length":7.18,"armaspec-stealth-recoil-spring-gen4-c.neck_d":0.774,"armaspec-stealth-recoil-spring-gen4-c.neck_length":0.475,"armaspec-stealth-recoil-spring-gen4-c.neck_taper":0.168,"armaspec-stealth-recoil-spring-gen4-c.od":0.946,"armaspec-stealth-recoil-spring-gen4-c.weight_length":1.278,"armaspec-stealth-recoil-spring-gen4-h.bumper_d":0.957,"armaspec-stealth-recoil-spring-gen4-h.bumper_length":1.395,"armaspec-stealth-recoil-spring-gen4-h.bumper_slot_depth":0.1,"armaspec-stealth-recoil-spring-gen4-h.bumper_slot_w":0.048,"armaspec-stealth-recoil-spring-gen4-h.cap_d":0.5,"armaspec-stealth-recoil-spring-gen4-h.cap_depth":0.3,"armaspec-stealth-recoil-spring-gen4-h.cap_t":0.08,"armaspec-stealth-recoil-spring-gen4-h.counterbore_d":0.61,"armaspec-stealth-recoil-spring-gen4-h.edge_break":0.02,"armaspec-stealth-recoil-spring-gen4-h.main_coils":25,"armaspec-stealth-recoil-spring-gen4-h.main_spring_od":0.394,"armaspec-stealth-recoil-spring-gen4-h.main_wire_d":0.034,"armaspec-stealth-recoil-spring-gen4-h.rod_d":0.176,"armaspec-stealth-recoil-spring-gen4-h.rod_end_d":0.33,"armaspec-stealth-recoil-spring-gen4-h.rod_end_length":0.3,"armaspec-stealth-recoil-spring-gen4-h.rod_hole_ahead":0.06,"armaspec-stealth-recoil-spring-gen4-h.rod_hole_d":0.11,"armaspec-stealth-recoil-spring-gen4-h.second_coils":10,"armaspec-stealth-recoil-spring-gen4-h.second_spring_od":0.65,"armaspec-stealth-recoil-spring-gen4-h.second_wire_d":0.045,"armaspec-stealth-recoil-spring-gen4-h.sleeve_d":0.39,"armaspec-stealth-recoil-spring-gen4-h.washer_front_x":2.768,"armaspec-stealth-recoil-spring-gen4-h.washer_length":0.212,"armaspec-stealth-recoil-spring-gen4-h.washer_od":0.709,"std.density.stainless_416":4.479793167596712,"std.receiver_extension.bore_d":1},"profiles":{},"bounds":{"min":[0,-0.4785,-0.4785],"max":[7.18,0.4785,0.4785]},"volume_in3":2.0511,"centroid":[3.8865,0,0],"shell":[3.4178,0,0],"area_in2":26.3853,"triangles":28502,"manifold":true,"slabs":[[0,-0.473,-0.473,0.798,0.473,0.473],[0.798,-0.39,-0.39,1.596,0.39,0.39],[1.596,-0.354,-0.354,3.191,0.354,0.354],[3.191,-0.198,-0.198,5.584,0.198,0.198],[5.584,-0.479,-0.479,7.18,0.479,0.479]],"slots":["weight","bumper","rod","spring"]},"armaspec-stealth-recoil-spring-gen4-h":{"part":"armaspec-stealth-recoil-spring-gen4-h","model":"armaspec-stealth-recoil-spring-gen4-h.glb","script":"armaspec_stealth_recoil_spring_gen4.py","inputs":{"armaspec-stealth-recoil-spring-gen4-h.bumper_d":0.957,"armaspec-stealth-recoil-spring-gen4-h.bumper_length":1.395,"armaspec-stealth-recoil-spring-gen4-h.bumper_slot_depth":0.1,"armaspec-stealth-recoil-spring-gen4-h.bumper_slot_w":0.048,"armaspec-stealth-recoil-spring-gen4-h.cap_d":0.5,"armaspec-stealth-recoil-spring-gen4-h.cap_depth":0.3,"armaspec-stealth-recoil-spring-gen4-h.cap_t":0.08,"armaspec-stealth-recoil-spring-gen4-h.counterbore_d":0.61,"armaspec-stealth-recoil-spring-gen4-h.edge_break":0.02,"armaspec-stealth-recoil-spring-gen4-h.length":7.18,"armaspec-stealth-recoil-spring-gen4-h.main_coils":25,"armaspec-stealth-recoil-spring-gen4-h.main_spring_od":0.394,"armaspec-stealth-recoil-spring-gen4-h.main_wire_d":0.034,"armaspec-stealth-recoil-spring-gen4-h.od":0.946,"armaspec-stealth-recoil-spring-gen4-h.rod_d":0.176,"armaspec-stealth-recoil-spring-gen4-h.rod_end_d":0.33,"armaspec-stealth-recoil-spring-gen4-h.rod_end_length":0.3,"armaspec-stealth-recoil-spring-gen4-h.rod_hole_ahead":0.06,"armaspec-stealth-recoil-spring-gen4-h.rod_hole_d":0.11,"armaspec-stealth-recoil-spring-gen4-h.second_coils":10,"armaspec-stealth-recoil-spring-gen4-h.second_spring_od":0.65,"armaspec-stealth-recoil-spring-gen4-h.second_wire_d":0.045,"armaspec-stealth-recoil-spring-gen4-h.sleeve_d":0.39,"armaspec-stealth-recoil-spring-gen4-h.washer_front_x":2.768,"armaspec-stealth-recoil-spring-gen4-h.washer_length":0.212,"armaspec-stealth-recoil-spring-gen4-h.washer_od":0.709,"armaspec-stealth-recoil-spring-gen4-h.weight_length":1.264,"std.density.stainless_416":4.479793167596712,"std.receiver_extension.bore_d":1},"profiles":{},"bounds":{"min":[0,-0.4785,-0.4785],"max":[7.18,0.4785,0.4785]},"volume_in3":2.1734,"centroid":[3.7226,0,0],"shell":[3.3818,0,0],"area_in2":26.7998,"triangles":27990,"manifold":true,"slabs":[[0,-0.473,-0.473,1.596,0.473,0.473],[1.596,-0.354,-0.354,3.191,0.354,0.354],[3.191,-0.198,-0.198,5.584,0.198,0.198],[5.584,-0.479,-0.479,7.18,0.479,0.479]],"slots":["weight","bumper","rod","spring"]},"armaspec-stealth-recoil-spring-gen4-h2":{"part":"armaspec-stealth-recoil-spring-gen4-h2","model":"armaspec-stealth-recoil-spring-gen4-h2.glb","script":"armaspec_stealth_recoil_spring_gen4.py","inputs":{"armaspec-stealth-recoil-spring-gen4-h.bumper_d":0.957,"armaspec-stealth-recoil-spring-gen4-h.bumper_length":1.395,"armaspec-stealth-recoil-spring-gen4-h.bumper_slot_depth":0.1,"armaspec-stealth-recoil-spring-gen4-h.bumper_slot_w":0.048,"armaspec-stealth-recoil-spring-gen4-h.cap_d":0.5,"armaspec-stealth-recoil-spring-gen4-h.cap_depth":0.3,"armaspec-stealth-recoil-spring-gen4-h.cap_t":0.08,"armaspec-stealth-recoil-spring-gen4-h.counterbore_d":0.61,"armaspec-stealth-recoil-spring-gen4-h.edge_break":0.02,"armaspec-stealth-recoil-spring-gen4-h.main_coils":25,"armaspec-stealth-recoil-spring-gen4-h.main_spring_od":0.394,"armaspec-stealth-recoil-spring-gen4-h.main_wire_d":0.034,"armaspec-stealth-recoil-spring-gen4-h.pocket_d":0.68,"armaspec-stealth-recoil-spring-gen4-h.rod_d":0.176,"armaspec-stealth-recoil-spring-gen4-h.rod_end_d":0.33,"armaspec-stealth-recoil-spring-gen4-h.rod_end_length":0.3,"armaspec-stealth-recoil-spring-gen4-h.rod_hole_ahead":0.06,"armaspec-stealth-recoil-spring-gen4-h.rod_hole_d":0.11,"armaspec-stealth-recoil-spring-gen4-h.second_coils":10,"armaspec-stealth-recoil-spring-gen4-h.second_spring_od":0.65,"armaspec-stealth-recoil-spring-gen4-h.second_wire_d":0.045,"armaspec-stealth-recoil-spring-gen4-h.sleeve_d":0.39,"armaspec-stealth-recoil-spring-gen4-h.washer_front_x":2.768,"armaspec-stealth-recoil-spring-gen4-h.washer_length":0.212,"armaspec-stealth-recoil-spring-gen4-h.washer_od":0.709,"armaspec-stealth-recoil-spring-gen4-h2.length":7.18,"armaspec-stealth-recoil-spring-gen4-h2.od":0.946,"armaspec-stealth-recoil-spring-gen4-h2.spring_pocket_depth":0.489,"armaspec-stealth-recoil-spring-gen4-h2.weight_length":1.753,"std.density.stainless_416":4.479793167596712,"std.receiver_extension.bore_d":1},"profiles":{},"bounds":{"min":[0,-0.4785,-0.4785],"max":[7.18,0.4785,0.4785]},"volume_in3":2.3395,"centroid":[3.5652,0,0],"shell":[3.2296,0,0],"area_in2":29.2573,"triangles":29526,"manifold":true,"slabs":[[0,-0.473,-0.473,1.994,0.473,0.473],[1.994,-0.354,-0.354,3.191,0.354,0.354],[3.191,-0.198,-0.198,5.584,0.198,0.198],[5.584,-0.479,-0.479,7.18,0.479,0.479]],"slots":["weight","bumper","rod","spring"]},"armaspec-stealth-recoil-spring-gen4-h3":{"part":"armaspec-stealth-recoil-spring-gen4-h3","model":"armaspec-stealth-recoil-spring-gen4-h3.glb","script":"armaspec_stealth_recoil_spring_gen4.py","inputs":{"armaspec-stealth-recoil-spring-gen4-h.bumper_d":0.957,"armaspec-stealth-recoil-spring-gen4-h.bumper_slot_depth":0.1,"armaspec-stealth-recoil-spring-gen4-h.bumper_slot_w":0.048,"armaspec-stealth-recoil-spring-gen4-h.cap_d":0.5,"armaspec-stealth-recoil-spring-gen4-h.cap_depth":0.3,"armaspec-stealth-recoil-spring-gen4-h.cap_t":0.08,"armaspec-stealth-recoil-spring-gen4-h.counterbore_d":0.61,"armaspec-stealth-recoil-spring-gen4-h.edge_break":0.02,"armaspec-stealth-recoil-spring-gen4-h.main_spring_od":0.394,"armaspec-stealth-recoil-spring-gen4-h.main_wire_d":0.034,"armaspec-stealth-recoil-spring-gen4-h.pocket_d":0.68,"armaspec-stealth-recoil-spring-gen4-h.rod_d":0.176,"armaspec-stealth-recoil-spring-gen4-h.rod_end_d":0.33,"armaspec-stealth-recoil-spring-gen4-h.rod_end_length":0.3,"armaspec-stealth-recoil-spring-gen4-h.rod_hole_ahead":0.06,"armaspec-stealth-recoil-spring-gen4-h.rod_hole_d":0.11,"armaspec-stealth-recoil-spring-gen4-h.second_coils":10,"armaspec-stealth-recoil-spring-gen4-h.second_spring_od":0.65,"armaspec-stealth-recoil-spring-gen4-h.second_wire_d":0.045,"armaspec-stealth-recoil-spring-gen4-h.sleeve_d":0.39,"armaspec-stealth-recoil-spring-gen4-h.washer_length":0.212,"armaspec-stealth-recoil-spring-gen4-h.washer_od":0.709,"armaspec-stealth-recoil-spring-gen4-h3.bumper_length":0.761,"armaspec-stealth-recoil-spring-gen4-h3.length":7.18,"armaspec-stealth-recoil-spring-gen4-h3.main_coils":27,"armaspec-stealth-recoil-spring-gen4-h3.od":0.946,"armaspec-stealth-recoil-spring-gen4-h3.spring_pocket_depth":0.18,"armaspec-stealth-recoil-spring-gen4-h3.washer_front_x":3.082,"armaspec-stealth-recoil-spring-gen4-h3.weight_length":1.962,"std.density.stainless_416":4.479793167596712,"std.receiver_extension.bore_d":1},"profiles":{},"bounds":{"min":[0,-0.4785,-0.4785],"max":[7.18,0.4785,0.4785]},"volume_in3":2.1267,"centroid":[2.8769,0,0],"shell":[3.1185,0,0],"area_in2":28.0603,"triangles":30294,"manifold":true,"slabs":[[0,-0.473,-0.473,1.994,0.473,0.473],[1.994,-0.354,-0.354,3.59,0.354,0.354],[3.59,-0.198,-0.198,6.382,0.198,0.198],[6.382,-0.479,-0.479,7.18,0.479,0.479]],"slots":["weight","bumper","rod","spring"]},"b5-bravo-stock":{"part":"b5-bravo-stock","model":"b5-bravo-stock.glb","script":"b5_bravo_stock.py","inputs":{"b5-bravo-stock.bore_diameter":1.162,"b5-bravo-stock.butt_behind_pin_pos1":9.333,"b5-bravo-stock.frame_rim_width":0.19,"b5-bravo-stock.frame_width":0.62,"b5-bravo-stock.keel_width":0.99,"b5-bravo-stock.lever_width":0.86,"b5-bravo-stock.lock_pin_ahead_of_butt":5.154,"b5-bravo-stock.qd_boss_diameter":0.692,"b5-bravo-stock.qd_boss_foot_diameter":0.806,"b5-bravo-stock.rail_channel_floor_below_axis":0.932,"b5-bravo-stock.rail_channel_width":0.53,"b5-bravo-stock.release_tab_span":1.03,"b5-bravo-stock.relief_face_inset":0,"b5-bravo-stock.rib_width":0.066,"b5-bravo-stock.top_hole_ahead_of_butt":5.186,"b5-bravo-stock.top_hole_diameter":0.32,"b5-bravo-stock.tube_axis_below_top":0.677,"b5-bravo-stock.web_thickness":0.07,"bcm-receiver-extension.tube_front_behind_pin":0.669,"bcm-receiver-extension.tube_length":7.25},"profiles":{"side":[[0,-0.348],[0.436,-4.725],[0.465,-4.81],[0.514,-4.869],[0.586,-4.912],[0.69,-4.931],[0.917,-4.902],[0.946,-4.921],[1.074,-4.921],[1.159,-4.902],[1.709,-4.433],[2.932,-3.442],[2.944,-3.445],[2.959,-3.848],[3.037,-3.912],[3.079,-3.916],[3.132,-3.897],[3.226,-3.802],[3.264,-3.798],[3.281,-3.748],[3.335,-3.727],[3.352,-3.677],[3.407,-3.656],[3.423,-3.606],[3.478,-3.584],[3.494,-3.535],[3.544,-3.518],[3.582,-3.452],[3.625,-3.442],[3.637,-3.397],[3.703,-3.364],[3.712,-3.321],[3.765,-3.302],[3.791,-3.243],[3.833,-3.234],[3.871,-3.167],[3.909,-3.162],[3.926,-3.113],[3.987,-3.084],[4.009,-3.03],[4.063,-3.008],[4.068,-2.97],[4.156,-2.883],[4.288,-2.802],[4.44,-2.769],[4.962,-2.759],[4.94,-2.771],[4.936,-2.814],[4.94,-3.046],[4.952,-3.063],[5.317,-3.068],[5.372,-3.042],[5.355,-2.75],[5.801,-2.731],[5.86,-2.676],[5.886,-2.57],[6.465,-2.575],[6.498,-2.56],[6.543,-2.515],[7.012,-1.686],[7.038,-1.655],[7.095,-1.64],[7.126,-1.6],[7.117,-1.211],[7.15,-0.965],[7.155,-0.69],[7.145,-0.23],[7.126,-0.102],[7.095,-0.043],[7.019,-0.014],[5.336,-0.005],[5.251,-0.028],[5.156,-0.033],[4.957,-0.005],[0.472,0],[0.453,-0.019],[0.192,-0.057],[0.107,-0.09],[0.047,-0.145],[0.009,-0.211]],"rear":[[-0.998,-1.1],[-0.987,-1.167],[-0.95,-1.241],[-0.751,-1.422],[-0.754,-4.155],[-0.729,-4.347],[-0.692,-4.462],[-0.595,-4.621],[-0.449,-4.763],[-0.301,-4.848],[-0.202,-4.882],[0.05,-4.907],[0.301,-4.848],[0.468,-4.752],[0.629,-4.58],[0.729,-4.362],[0.754,-4.199],[0.751,-1.429],[0.969,-1.215],[0.998,-1.137],[0.998,-1.041],[0.965,-0.96],[0.758,-0.627],[0.754,-0.597],[0.64,-0.405],[0.499,-0.205],[0.405,-0.126],[0.276,-0.052],[0.135,-0.011],[-0.002,0],[-0.054,0],[-0.19,-0.022],[-0.294,-0.063],[-0.42,-0.137],[-0.51,-0.22],[-0.584,-0.32],[-0.962,-0.956],[-0.991,-1.03]],"plan":[[0,0.036],[0.014,-0.014],[0,-0.039],[0.014,-0.082],[0.004,-0.153],[0.014,-0.164],[0.007,-0.235],[0.021,-0.257],[0.014,-0.321],[0.029,-0.346],[0.021,-0.389],[0.054,-0.556],[0.103,-0.66],[0.159,-0.708],[0.255,-0.744],[0.523,-0.744],[0.74,-1.001],[6.116,-1.004],[6.227,-0.979],[6.662,-0.744],[7.093,-0.672],[7.156,-0.628],[7.17,-0.592],[7.17,0.592],[7.156,0.631],[7.115,0.669],[6.951,0.69],[6.762,0.74],[6.173,1.004],[0.74,1.004],[0.53,0.758],[0.237,0.754],[0.166,0.726],[0.096,0.663],[0.057,0.585],[0.032,0.4],[0.018,0.378],[0.025,0.321],[0.011,0.303],[0.018,0.235],[0.004,0.193],[0.014,0.071]]},"features":{"side":{"through":[[[1.408,-1.87],[1.422,-1.837],[1.477,-1.797],[2.776,-1.787],[2.809,-1.802],[2.845,-1.851],[2.826,-1.932],[2.767,-1.968],[1.776,-1.977],[1.453,-1.968],[1.413,-1.918]],[[1.636,-2.577],[1.645,-2.511],[1.674,-2.458],[1.733,-2.404],[1.795,-2.38],[1.87,-2.38],[1.951,-2.418],[2.006,-2.482],[2.025,-2.539],[2.025,-2.601],[1.991,-2.681],[1.932,-2.736],[1.847,-2.764],[1.771,-2.755],[1.709,-2.721],[1.659,-2.662]],[[1.19,-4.227],[1.19,-4.16],[1.235,-4.106],[2.179,-3.305],[2.254,-3.286],[2.309,-3.321],[2.318,-3.407],[2.254,-3.475],[1.292,-4.277],[1.23,-4.272]]],"buttpad":[[[-0.211,0.187],[0.462,0.187],[0.462,0.007],[0.486,-0.334],[0.51,-0.571],[0.538,-0.808],[0.567,-1.045],[0.595,-1.283],[0.619,-1.52],[0.642,-1.757],[0.661,-1.994],[0.685,-2.231],[0.714,-2.468],[0.737,-2.705],[0.761,-2.942],[0.785,-3.179],[0.808,-3.416],[0.832,-3.653],[0.851,-3.89],[0.87,-4.127],[0.889,-4.364],[0.913,-4.601],[0.932,-4.838],[0.941,-5.123],[-0.211,-5.123]]],"frame":[[[0.87,-1.652],[7.375,-1.652],[7.375,-4.08],[5.891,-4.08],[5.891,-2.563],[5.867,-2.373],[5.763,-2.221],[5.573,-2.145],[5.194,-2.112],[4.435,-2.107],[4.056,-2.126],[3.791,-2.183],[3.639,-2.335],[3.487,-2.525],[3.298,-2.714],[3.108,-2.923],[2.994,-3.056],[2.947,-3.132],[2.947,-5.313],[1.178,-5.313],[1.178,-4.933],[1.164,-4.838],[1.131,-4.601],[1.102,-4.364],[1.055,-3.89],[1.031,-3.653],[0.993,-3.179],[0.951,-2.705],[0.932,-2.468],[0.913,-2.231],[0.889,-1.994],[0.87,-1.7]]],"lever":[[[3.791,-2.183],[4.056,-2.126],[4.435,-2.107],[5.194,-2.112],[5.573,-2.145],[5.763,-2.221],[5.867,-2.373],[5.891,-2.563],[5.891,-4.08],[2.947,-4.08],[2.947,-3.132],[2.994,-3.056],[3.108,-2.923],[3.298,-2.714],[3.487,-2.525],[3.639,-2.335]]],"under":[[[0.808,-0.998],[7.375,-0.998],[7.375,-1.652],[0.87,-1.652]]],"pin":[[[4.943,-2.743],[5.369,-2.743],[5.369,-3.084],[4.943,-3.084]]],"tab":[[[1.008,-3.283],[1.283,-3.283],[1.283,-3.781],[1.008,-3.781]]],"qd":[[[1.548,-2.288],[2.117,-2.288],[2.117,-2.857],[1.548,-2.857]]]},"rear":{},"plan":{}},"placement":{"side":{"plane":"xy","offset":{"y":"tube_axis_below_top"}},"rear":{"plane":"zy","offset":{"y":"tube_axis_below_top"}},"plan":{"plane":"xz","offset":{}}},"bounds":{"min":[0,-4.23,-0.998],"max":[7.155,0.677,0.998]},"volume_in3":16.0938,"centroid":[2.6988,-1.1289,0.0014],"shell":[2.9992,-1.1405,0.001],"area_in2":133.5625,"triangles":12170,"manifold":true,"slabs":[[0,-3.661,-0.744,0.398,0.65,0.756],[0.398,-4.23,-0.998,1.59,0.677,0.998],[1.59,-3.857,-0.998,1.988,0.676,0.998],[1.988,-3.53,-0.998,2.385,0.675,0.998],[2.385,-3.239,-0.998,3.18,0.675,0.998],[3.18,-3.171,-0.998,3.578,0.674,0.998],[3.578,-2.783,-0.998,3.975,0.674,0.998],[3.975,-2.413,-0.998,4.373,0.673,0.998],[4.373,-2.107,-0.998,4.77,0.673,0.998],[4.77,-2.407,-0.998,5.565,0.672,0.998],[5.565,-2.064,-0.998,5.963,0.671,0.998],[5.963,-1.897,-0.998,6.36,0.669,0.998],[6.36,-1.898,-0.907,6.758,0.667,0.92],[6.758,-1.459,-0.728,7.155,0.664,0.742]],"slots":["body","buttpad","qd","pin"]},"b5-enhanced-sopmod-stock":{"part":"b5-enhanced-sopmod-stock","model":"b5-enhanced-sopmod-stock.glb","script":"b5_enhanced_sopmod_stock.py","inputs":{"b5-enhanced-sopmod-stock.block_width":0.68,"b5-enhanced-sopmod-stock.bore_diameter":1.161,"b5-enhanced-sopmod-stock.butt_behind_pin_pos1":9.309,"b5-enhanced-sopmod-stock.frame_width":0.5,"b5-enhanced-sopmod-stock.lever_width":0.924,"b5-enhanced-sopmod-stock.qd_span":0.748,"b5-enhanced-sopmod-stock.rail_channel_floor_below_axis":0.881,"b5-enhanced-sopmod-stock.rail_channel_width":0.505,"b5-enhanced-sopmod-stock.release_tab_span":1.032,"b5-enhanced-sopmod-stock.storage_axis_below_top":1.478,"b5-enhanced-sopmod-stock.storage_axis_off_centre":0.726,"b5-enhanced-sopmod-stock.storage_cap_diameter":0.66,"b5-enhanced-sopmod-stock.storage_cap_front_ahead_of_butt":7.39,"b5-enhanced-sopmod-stock.storage_pocket_diameter":0.762,"b5-enhanced-sopmod-stock.strut_flare_start_ahead_of_butt":2.29,"b5-enhanced-sopmod-stock.strut_width_at_plate":0.995,"b5-enhanced-sopmod-stock.top_hole_ahead_of_butt":5.158,"b5-enhanced-sopmod-stock.top_hole_diameter":0.34,"b5-enhanced-sopmod-stock.tube_axis_below_top":0.694,"b5-enhanced-sopmod-stock.wing_tip_radius":0.475,"bcm-receiver-extension.tube_front_behind_pin":0.669,"bcm-receiver-extension.tube_length":7.25},"profiles":{"side":[[0,-0.272],[0.003,-4.675],[0.012,-4.732],[0.05,-4.802],[0.152,-4.88],[0.247,-4.898],[0.469,-4.897],[0.483,-4.878],[0.535,-4.92],[0.676,-4.905],[0.693,-4.86],[0.683,-4.747],[0.694,-4.716],[1.606,-4.069],[3.19,-2.979],[3.194,-3.335],[3.273,-3.422],[3.358,-3.435],[3.443,-3.407],[3.457,-3.378],[3.494,-3.373],[3.56,-3.316],[3.588,-3.316],[3.612,-3.283],[3.64,-3.287],[3.659,-3.254],[3.692,-3.254],[3.715,-3.221],[3.748,-3.221],[3.767,-3.188],[3.795,-3.192],[3.814,-3.159],[3.842,-3.164],[3.87,-3.126],[3.899,-3.13],[3.917,-3.097],[3.95,-3.097],[3.964,-3.068],[3.997,-3.068],[4.021,-3.035],[4.054,-3.035],[4.068,-3.006],[4.101,-3.006],[4.124,-2.973],[4.157,-2.973],[4.171,-2.944],[4.204,-2.944],[4.228,-2.911],[4.256,-2.916],[4.275,-2.883],[4.308,-2.882],[4.331,-2.849],[4.36,-2.854],[4.383,-2.821],[4.416,-2.82],[4.444,-2.782],[4.543,-2.744],[4.623,-2.729],[4.925,-2.728],[4.92,-3.023],[4.946,-3.039],[5.045,-3.043],[5.078,-3.067],[5.187,-3.066],[5.224,-3.042],[5.314,-3.042],[5.345,-3.025],[5.341,-2.73],[5.907,-2.736],[5.954,-2.717],[5.989,-2.681],[6.014,-2.57],[6.515,-2.567],[6.787,-1.997],[6.808,-1.971],[6.856,-1.971],[6.921,-1.88],[6.952,-1.873],[7.017,-1.745],[7.269,-1.211],[7.259,-1.178],[7.445,-0.705],[7.399,-0.077],[7.387,-0.056],[7.273,0],[7.137,-0.01],[5.315,-0.002],[5.225,-0.022],[5.103,-0.022],[4.975,-0.004],[4.668,-0.001],[0.501,-0.007],[0.48,-0.019],[0.473,-0.05],[0.459,-0.003],[0.407,-0.003],[0.19,-0.023],[0.114,-0.052],[0.042,-0.126],[0.014,-0.187]],"rear":[[-1.203,-1.516],[-1.16,-1.679],[-1.09,-1.788],[-0.975,-1.882],[-0.823,-1.935],[-0.747,-2.015],[-0.75,-4.216],[-0.711,-4.41],[-0.655,-4.538],[-0.591,-4.633],[-0.43,-4.783],[-0.313,-4.851],[-0.193,-4.893],[0.044,-4.918],[0.182,-4.897],[0.288,-4.861],[0.405,-4.801],[0.501,-4.73],[0.64,-4.562],[0.729,-4.357],[0.754,-4.138],[0.75,-2.011],[0.826,-1.935],[0.9,-1.918],[1,-1.868],[1.107,-1.767],[1.189,-1.605],[1.203,-1.438],[1.15,-1.261],[0.517,-0.232],[0.43,-0.149],[0.303,-0.067],[0.154,-0.014],[-0.002,0],[-0.062,0],[-0.203,-0.028],[-0.334,-0.085],[-0.455,-0.17],[-0.538,-0.26],[-1.139,-1.244],[-1.192,-1.378]],"plan":[[0,0.44],[0,0],[0,-0.433],[0.053,-0.617],[0.146,-0.714],[0.266,-0.749],[0.731,-0.749],[1.503,-1.196],[7.017,-1.2],[7.091,-1.196],[7.141,-1.172],[7.431,-0.8],[7.431,0.803],[7.16,1.156],[7.077,1.2],[1.506,1.2],[0.721,0.745],[0.248,0.749],[0.171,0.728],[0.104,0.685],[0.046,0.603]]},"features":{"side":{"through":[[[1.348,-2.364],[1.348,-2.317],[1.388,-2.263],[1.42,-2.248],[3.162,-2.247],[3.216,-2.287],[3.231,-2.344],[3.212,-2.391],[3.158,-2.427],[1.436,-2.437],[1.367,-2.402]],[[0.947,-3.915],[0.948,-2.636],[0.962,-2.598],[1.016,-2.557],[1.083,-2.566],[1.128,-2.625],[1.126,-3.914],[1.117,-3.942],[1.058,-3.987],[0.992,-3.978]],[[1.598,-3.075],[1.611,-2.99],[1.649,-2.929],[1.698,-2.888],[1.769,-2.864],[1.835,-2.869],[1.911,-2.906],[1.951,-2.951],[1.98,-3.016],[1.98,-3.097],[1.957,-3.158],[1.903,-3.218],[1.828,-3.251],[1.757,-3.251],[1.681,-3.219],[1.626,-3.16]],[[6.237,-2.26],[6.281,-2.191],[6.352,-2.176],[6.397,-2.23],[6.402,-2.282],[6.388,-2.315],[6.325,-2.361],[6.296,-2.361],[6.261,-2.335]],[[5.108,-2.922],[5.113,-2.889],[5.143,-2.873],[5.183,-2.903],[5.153,-2.948],[5.125,-2.944]]],"buttpad":[[[-0.303,0.269],[0.485,0.274],[0.48,-5.201],[-0.27,-5.206]]],"frame":[[[0.664,-1.977],[6.068,-1.978],[6.08,-4.035],[6.033,-4.035],[6.023,-2.431],[6.008,-2.233],[5.941,-2.139],[5.846,-2.102],[4.525,-2.109],[4.384,-2.134],[4.195,-2.215],[3.96,-2.372],[3.725,-2.539],[3.49,-2.729],[3.265,-2.905],[3.195,-2.976],[3.208,-5.279],[0.665,-5.294]]],"strut":[[[0.646,-4.633],[3.194,-2.865],[3.196,-3.25],[0.649,-5.016]]],"lever":[[[3.195,-2.976],[3.265,-2.905],[3.49,-2.729],[3.725,-2.539],[3.96,-2.372],[4.195,-2.215],[4.384,-2.134],[4.525,-2.109],[5.846,-2.102],[5.941,-2.139],[6.008,-2.233],[6.023,-2.431],[6.033,-4.035],[3.201,-4.052]]],"block":[[[6.068,-1.978],[7.686,-1.977],[7.699,-4.026],[6.08,-4.035]]],"pin":[[[4.939,-2.725],[5.355,-2.723],[5.357,-3.067],[4.941,-3.07]]],"tab":[[[0.691,-3.312],[0.898,-3.311],[0.901,-3.802],[0.693,-3.803]]],"qd":[[[1.475,-2.75],[2.103,-2.747],[2.107,-3.37],[1.479,-3.373]]]},"rear":{},"plan":{}},"placement":{"side":{"plane":"xy","offset":{"y":"tube_axis_below_top"}},"rear":{"plane":"zy","offset":{"y":"tube_axis_below_top"}},"plan":{"plane":"xz","offset":{}}},"bounds":{"min":[0,-4.224,-1.2],"max":[7.431,0.694,1.2]},"volume_in3":21.7043,"centroid":[2.991,-1.144,-0.0009],"shell":[3.3504,-0.9691,0.0001],"area_in2":197.5761,"triangles":11012,"manifold":true,"slabs":[[0,-4.204,-0.749,0.391,0.69,0.749],[0.391,-4.224,-1.056,0.782,0.691,1.056],[0.782,-3.959,-1.056,1.173,0.688,1.056],[1.173,-3.682,-1.196,1.564,0.689,1.2],[1.564,-3.404,-1.196,1.956,0.689,1.2],[1.956,-3.134,-1.197,2.347,0.69,1.2],[2.347,-2.865,-1.197,2.738,0.69,1.2],[2.738,-2.596,-1.197,3.129,0.691,1.2],[3.129,-2.741,-1.197,3.52,0.691,1.2],[3.52,-2.657,-1.198,3.911,0.692,1.2],[3.911,-2.414,-1.198,4.302,0.692,1.2],[4.302,-2.188,-1.198,4.693,0.693,1.2],[4.693,-2.376,-1.199,5.475,0.693,1.2],[5.475,-2.042,-1.199,6.258,0.691,1.2],[6.258,-1.875,-1.2,6.649,0.688,1.2],[6.649,-1.593,-1.2,7.04,0.686,1.2],[7.04,-1.114,-1.199,7.431,0.694,1.2]],"slots":["body","buttpad","qd","pin"]},"b5-type-23-p-grip":{"part":"b5-type-23-p-grip","model":"b5-type-23-p-grip.glb","script":"b5_type_23_p_grip.py","inputs":{"b5-type-23-p-grip.back_strap_lean":18.947,"b5-type-23-p-grip.back_strap_round":0.45,"b5-type-23-p-grip.block_front_x":1.241,"b5-type-23-p-grip.front_strap_lean":13.251,"b5-type-23-p-grip.front_strap_round":0.25,"b5-type-23-p-grip.groove_depth":0.02,"b5-type-23-p-grip.groove_width":0.039,"b5-type-23-p-grip.height":4.84,"b5-type-23-p-grip.length":2.73,"b5-type-23-p-grip.lug_slot_width":0.405,"b5-type-23-p-grip.seat_x":-0.066,"b5-type-23-p-grip.shoulder_length":0.4,"b5-type-23-p-grip.thickness":1.26,"b5-type-23-p-grip.top_block_width":0.88,"std.ar15.deck_y":0.2485,"std.ar15.grip_lug_depth":0.93,"std.ar15.grip_lug_face_angle":60,"std.ar15.grip_lug_face_from_pin":1.228,"std.ar15.grip_lug_front_from_rear_face":2.3,"std.ar15.grip_lug_length":1.25,"std.ar15.grip_lug_width":0.375,"std.ar15.grip_seat_below_deck":1.318,"std.ar15.rear_underside_arc_center_below_seat":0.1928,"std.ar15.rear_underside_arc_center_x":-1.0238,"std.ar15.rear_underside_arc_r_fullest":0.716,"std.ar15.rear_underside_round_r":0.44,"std.ar15.receiver_rear_x":-1.125},"profiles":{"side":[[-1.493,-3.664],[-1.493,-3.708],[-1.479,-3.747],[-1.438,-3.788],[-1.302,-3.827],[-0.952,-3.91],[-0.539,-3.992],[-0.5,-3.992],[-0.389,-4.021],[-0.374,-4.016],[-0.359,-4.026],[-0.223,-4.046],[-0.029,-4.089],[0.267,-4.138],[0.355,-4.118],[0.401,-4.077],[0.415,-4.033],[0.381,-4.014],[0.391,-3.975],[0.403,-3.963],[0.447,-3.953],[0.469,-3.917],[0.474,-3.839],[0.488,-3.82],[0.493,-3.761],[0.503,-3.747],[0.503,-3.698],[0.522,-3.664],[0.532,-3.592],[0.546,-3.558],[0.542,-3.533],[0.556,-3.509],[0.556,-3.48],[0.571,-3.46],[0.571,-3.417],[0.585,-3.392],[0.58,-3.368],[0.595,-3.339],[0.619,-3.208],[0.648,-3.14],[0.648,-3.111],[0.673,-3.033],[0.673,-2.994],[0.692,-2.941],[0.702,-2.853],[0.726,-2.79],[0.726,-2.756],[0.745,-2.717],[0.741,-2.688],[0.755,-2.664],[0.75,-2.64],[0.77,-2.61],[0.77,-2.572],[0.794,-2.494],[0.799,-2.436],[0.833,-2.338],[0.833,-2.314],[0.847,-2.295],[0.843,-2.28],[0.862,-2.232],[0.872,-2.149],[0.901,-2.062],[0.901,-2.028],[0.93,-1.945],[0.93,-1.911],[0.949,-1.872],[0.945,-1.848],[0.954,-1.833],[0.906,-1.795],[0.915,-1.751],[0.928,-1.739],[0.952,-1.744],[0.964,-1.731],[0.959,-1.717],[0.974,-1.683],[0.998,-1.552],[1.042,-1.455],[1.112,-1.37],[1.217,-1.299],[1.226,-1.265],[1.241,-0.24],[1.226,-0.182],[1.202,-0.134],[1.144,-0.066],[1.088,-0.029],[1.005,-0.005],[0.005,0.005],[-0.007,0.017],[-0.061,0.168],[-0.124,0.279],[-0.206,0.386],[-0.364,0.529],[-0.539,0.627],[-0.622,0.656],[-0.777,0.685],[-0.787,0.695],[-0.942,0.695],[-0.952,0.685],[-0.996,0.68],[-1.022,0.648],[-1.037,0.61],[-1.037,0.036],[-1.022,0.007],[-0.986,-0.029],[-0.923,-0.058],[-0.889,-0.058],[-0.826,-0.078],[-0.714,-0.136],[-0.653,-0.187],[-0.576,-0.274],[-0.522,-0.367],[-0.474,-0.498],[-0.464,-0.644],[-0.474,-0.731],[-0.503,-0.838],[-0.629,-1.163],[-1.105,-2.494],[-1.484,-3.655]]},"features":{"side":{"panel":[[[-0.282,-1.27],[0.753,-1.416],[0.136,-3.975],[-1.044,-3.766]]],"strap_groove":[[[0.845,-1.795],[0.864,-1.795],[0.34,-3.941],[0.321,-3.941]]]}},"placement":{"side":{"plane":"xy","offset":{}}},"bounds":{"min":[-1.493,-4.138,-0.63],"max":[1.241,0.6821,0.63]},"volume_in3":8.1632,"centroid":[-0.0837,-2.1456,0],"shell":[-0.0316,-1.8521,0],"area_in2":30.9677,"triangles":46870,"manifold":true,"receiver":{"slot":{"width":0.405,"clear_of_lug":0.015,"rear_x":-0.024,"floor_at_rear_y":-0.3138,"foot_x":1.0692,"bottom_y":-0.945},"scoop":{"axis_x":-0.9578,"axis_y":-0.1928,"on_centre_plane_r":0.701,"across_r":0.455}},"slabs":[[-1.452,-4.138,-0.63,0.495,-3.767,0.63],[-1.493,-3.767,-0.63,0.579,-3.396,0.63],[-1.399,-3.396,-0.63,0.67,-3.026,0.63],[-1.278,-3.026,-0.63,0.754,-2.655,0.63],[-1.157,-2.655,-0.63,0.845,-2.284,0.63],[-1.03,-2.284,-0.63,0.934,-1.913,0.63],[-0.897,-1.913,-0.63,1.002,-1.543,0.63],[-0.765,-1.543,-0.63,1.227,-1.172,0.63],[-0.632,-1.172,-0.63,1.233,-0.801,0.63],[-0.499,-0.801,-0.447,1.238,-0.43,0.447],[-0.884,-0.43,-0.444,1.241,-0.059,0.444],[-1.037,-0.059,-0.444,1.134,0.311,0.444],[-1.037,0.311,-0.444,-0.149,0.682,0.444]],"slots":["body","texture"]},"bad-workhorse-lower":{"part":"bad-workhorse-lower","model":"bad-workhorse-lower.glb","script":"bad_workhorse_lower.py","inputs":{"bad-workhorse-lower.bolt_catch_boss_bottom_y":-0.05,"bad-workhorse-lower.bolt_catch_boss_front_x":3.576,"bad-workhorse-lower.bolt_catch_boss_rear_x":3.013,"bad-workhorse-lower.bolt_catch_gap_front_x":3.375,"bad-workhorse-lower.bolt_catch_gap_rear_x":3.203,"bad-workhorse-lower.buffer_axis_above_pin":0.8775,"bad-workhorse-lower.fence_bottom_y":-0.91,"bad-workhorse-lower.fence_corner_r":0.1,"bad-workhorse-lower.fence_front_x":3.565,"bad-workhorse-lower.fence_rear_x":3.02,"bad-workhorse-lower.fence_top_y":-0.22,"bad-workhorse-lower.grip_seat_y":-1.0695,"bad-workhorse-lower.grip_shelf_bottom_y":-2.002,"bad-workhorse-lower.grip_shelf_top_x":0.122,"bad-workhorse-lower.hammer_pin_x":2.771,"bad-workhorse-lower.hammer_pin_y":-0.375,"bad-workhorse-lower.magwell_front_x":6.179,"bad-workhorse-lower.magwell_wall_curve_bottom_y_left":-1.12,"bad-workhorse-lower.magwell_wall_curve_top_y_left":-0.7,"bad-workhorse-lower.magwell_wall_rear_x":3.619,"bad-workhorse-lower.magwell_wall_rear_x_left":3.455,"bad-workhorse-lower.magwell_wall_upper_rear_x_left":2.948,"bad-workhorse-lower.rear_behind_pin":1.125,"bad-workhorse-lower.selector_x":0.803,"bad-workhorse-lower.selector_y":-0.466,"bad-workhorse-lower.tower_front_x":-0.317,"bad-workhorse-lower.trigger_guard_front_x":3.3425,"bad-workhorse-lower.trigger_guard_front_y":-2.18,"bad-workhorse-lower.trigger_guard_rear_x":1.4985,"bad-workhorse-lower.trigger_guard_rear_y":-2.18,"bad-workhorse-lower.trigger_pin_x":1.928,"bad-workhorse-lower.trigger_pin_y":-0.689,"bad-workhorse-lower.well_roll_bottom_y":-0.204,"bad-workhorse-lower.well_roll_crest_out":0.8,"bad-workhorse-lower.well_roll_front_x":6.231,"bad-workhorse-lower.well_roll_rear_round":0.19,"bad-workhorse-lower.well_roll_rear_x":2.905,"std.ar15.bolt_catch_boss_out":0.618,"std.ar15.bolt_catch_plunger_hole_d":0.156,"std.ar15.bolt_catch_plunger_hole_depth":0.4703,"std.ar15.bolt_catch_plunger_hole_y":-0.195,"std.ar15.bolt_catch_slot_bottom_y":-0.38,"std.ar15.bolt_catch_slot_floor":0.4409,"std.ar15.bolt_catch_slot_front_x":3.375,"std.ar15.bolt_catch_slot_width":0.172,"std.ar15.bore_axis_y":0.8775,"std.ar15.buffer_tower_front_x":-0.628,"std.ar15.buffer_tower_od":1.392,"std.ar15.deck_front_x":6.194,"std.ar15.deck_y":0.2485,"std.ar15.fcg_pin_hole_d":0.15675,"std.ar15.fcg_pocket_corner_r":0.218,"std.ar15.fcg_pocket_depth":1.249,"std.ar15.fcg_pocket_front_x":3.11,"std.ar15.fcg_pocket_length":2.87,"std.ar15.fcg_pocket_width":0.69,"std.ar15.front_lug_slot_width":0.5,"std.ar15.grip_lug_width":0.375,"std.ar15.lower_body_width":0.88,"std.ar15.mag_catch_boss_edge_r":0.059,"std.ar15.mag_catch_boss_proud":0.0906,"std.ar15.mag_catch_boss_r":0.253,"std.ar15.mag_catch_boss_x":4.262,"std.ar15.mag_catch_cbore_d":0.312,"std.ar15.mag_catch_cbore_depth":0.25,"std.ar15.mag_catch_fence_out":0.549,"std.ar15.mag_catch_hole_d":0.2055,"std.ar15.mag_catch_slot_bottom_y":-0.689,"std.ar15.mag_catch_slot_floor":0.3799,"std.ar15.mag_catch_slot_front_x":4.557,"std.ar15.mag_catch_slot_h":0.252,"std.ar15.mag_catch_slot_rear_x":3.048,"std.ar15.mag_catch_x":3.291,"std.ar15.mag_catch_y":-0.565,"std.ar15.mag_release_pocket_depth":0.617,"std.ar15.mag_release_pocket_h":0.515,"std.ar15.mag_release_pocket_w":0.319,"std.ar15.magwell_band_bottom_y":-1.959,"std.ar15.magwell_band_front_x":4.549,"std.ar15.magwell_band_proud":0.059,"std.ar15.magwell_band_rear_x":3.975,"std.ar15.magwell_band_side":0.084,"std.ar15.magwell_box_length":2.398,"std.ar15.magwell_corner_r":0.062,"std.ar15.magwell_front_inner_x":6.025,"std.ar15.magwell_length":2.553,"std.ar15.magwell_outside_width":1.098,"std.ar15.magwell_spine_slot_width":0.47,"std.ar15.magwell_width":0.898,"std.ar15.pin_spacing":6.375,"std.ar15.pivot_hole_d":0.251,"std.ar15.rear_lug_slot_depth":0.63,"std.ar15.rear_lug_slot_rear_x":-0.402,"std.ar15.rear_lug_slot_width":0.5,"std.ar15.rear_underside_round_r":0.44,"std.ar15.rear_wall_arc_r":0.75,"std.ar15.safety_detent_boss_below_deck":0.455,"std.ar15.safety_detent_boss_face":0.53,"std.ar15.safety_detent_boss_from_rear":0.36,"std.ar15.safety_detent_boss_length":0.43,"std.ar15.selector_hole_d":0.376,"std.ar15.takedown_hole_d":0.251,"std.ar15.takedown_spotface_d":0.44,"std.ar15.takedown_spotface_depth":0.04,"std.ar15.trigger_guard_ear_gap":0.442,"std.ar15.trigger_guard_ears_width":0.659,"std.ar15.trigger_guard_front_hole_d":0.1265,"std.ar15.trigger_guard_front_spotface_d":0.25,"std.ar15.trigger_guard_front_spotface_floor":0.3219,"std.ar15.trigger_guard_rear_hole_d":0.1285,"std.ar15.trigger_pin_x":1.928,"std.ar15.trigger_slot_front_ahead_of_pin":0.52,"std.ar15.trigger_slot_length":0.68,"std.ar15.trigger_slot_width":0.312,"std.ar15.upper_rear_face_x":-0.621,"std.receiver_extension.milspec_od":1.148},"profiles":{"side":[[-1.159,0.335],[-1.121,-0.207],[-1.13,-0.533],[-0.853,-0.558],[-0.645,-0.653],[-0.49,-0.783],[-0.403,-0.903],[-0.341,-1.043],[-0.307,-1.071],[0.12,-1.067],[0.131,-1.454],[0.174,-1.513],[0.975,-1.977],[1.039,-2.002],[1.172,-2.008],[1.175,-2.323],[1.203,-2.357],[1.615,-2.365],[1.668,-2.318],[1.687,-2.274],[1.679,-2.204],[1.528,-2.059],[1.462,-1.971],[1.395,-1.831],[1.366,-1.704],[1.381,-1.501],[1.43,-1.373],[1.492,-1.277],[1.642,-1.151],[1.85,-1.064],[2.948,-1.061],[3.072,-1.112],[3.24,-1.226],[3.325,-1.334],[3.389,-1.483],[3.403,-1.545],[3.392,-1.781],[3.325,-1.947],[3.169,-2.155],[3.177,-2.243],[3.196,-2.28],[3.275,-2.344],[3.381,-2.368],[3.771,-2.283],[5.095,-2.041],[6.144,-1.873],[6.178,-1.833],[6.179,-1.766],[6.112,-1.68],[6.082,-1.588],[6.085,-0.661],[6.099,-0.543],[6.153,-0.418],[6.239,-0.315],[6.423,-0.226],[6.547,-0.122],[6.573,-0.065],[6.58,0.023],[6.537,0.117],[6.484,0.171],[6.434,0.196],[6.198,0.211],[6.141,0.236],[0.189,0.241],[-0.027,0.259],[-0.149,0.309],[-0.276,0.439],[-0.35,0.566],[-0.408,0.756],[-0.433,1.12],[-0.495,1.467],[-0.591,1.54],[-0.629,1.553],[-0.961,1.552],[-1.069,1.526],[-1.103,1.497],[-1.125,1.426],[-1.13,1.333],[-1.124,0.6]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{}}},"bounds":{"min":[-1.125,-2.368,-0.6986],"max":[6.58,1.5735,0.8]},"volume_in3":5.1151,"centroid":[2.412,-0.6012,0.0286],"shell":[2.8771,-0.6489,0.0093],"area_in2":76.3531,"triangles":22722,"manifold":true,"interior":{"pocket":{"x":[0.24,3.11],"z":0.345,"floor_y":-1.0005},"rear_lug_slot":{"x":[-0.402,0.458],"z":0.25,"floor_y":-0.3815},"safety_detent_boss":{"x":[0.6,1.03],"face_z":0.185,"top_y":-0.2065},"trigger_slot":{"x":[1.768,2.448],"z":0.156},"magazine_well":{"x":[3.472,6.025],"z":0.449}},"holes":{"takedown":{"x":0,"y":0,"d":0.251},"pivot":{"x":6.375,"y":0,"d":0.251},"selector":{"x":0.803,"y":-0.466,"d":0.376},"hammer":{"x":2.771,"y":-0.375,"d":0.1568},"trigger":{"x":1.928,"y":-0.689,"d":0.1568},"guard rear":{"x":1.4985,"y":-2.18,"d":0.1285},"guard front":{"x":3.3425,"y":-2.18,"d":0.1265}},"catches":{"button_pocket":{"x":3.291,"y":-0.565,"floor_z":-0.068,"face_z":0.549},"catch_slot":{"x":[3.048,4.557],"floor_z":-0.3799},"bolt_catch_slot":{"x":[3.203,3.375],"bottom_y":-0.38,"floor_z":-0.4409}},"grip_mount":{"lug":{"seat_y":-1.0695,"x":[0.12,1.172],"width":0.375},"ears":{"width":0.659,"gap":0.442,"gap_top_y":-2.008,"rear_x":[1.172,1.8369],"front_x":[2.9687,3.455]},"rear_underside":{"round_r":0.44,"x":[-1.13,-0.307]}},"rear_walls":{"r":0.75,"centre":[0.122,0.9985],"x":[-0.621,0.122],"meets_face_y":0.8963,"runs_out":[0.055,0.2515],"toe_x":[-0.1255,0.055]},"deck":{"y":0.2485,"x":[-0.02,6.194]},"slabs":[[-1.125,-0.609,-0.696,-0.74,1.573,0.696],[-0.74,-1.01,-0.696,-0.355,1.573,0.696],[-0.355,-1.071,-0.524,0.031,0.419,0.524],[0.031,-1.653,-0.44,0.416,0.254,0.44],[0.416,-1.876,-0.44,0.801,0.249,0.44],[0.801,-2.365,-0.44,1.957,0.249,0.44],[1.957,-1.064,-0.44,2.727,0.249,0.44],[2.727,-1.14,-0.618,3.113,0.249,0.8],[3.113,-2.368,-0.618,3.883,0.249,0.8],[3.883,-2.262,-0.699,4.268,0.249,0.8],[4.268,-2.192,-0.699,4.654,0.249,0.8],[4.654,-2.122,-0.549,5.039,0.249,0.8],[5.039,-2.051,-0.549,5.424,0.249,0.8],[5.424,-1.988,-0.549,5.809,0.249,0.8],[5.809,-1.927,-0.549,6.195,0.249,0.8],[6.195,-0.368,-0.44,6.58,0.249,0.8]],"slots":["receiver"]},"bca-556-16-mid-barrel":{"part":"bca-556-16-mid-barrel","model":"bca-556-16-mid-barrel.glb","script":"bca_556_16_mid_barrel.py","inputs":{"bca-556-16-mid-barrel.bore_d":0.2195,"bca-556-16-mid-barrel.extension_rear_x":-0.996,"bca-556-16-mid-barrel.flange_front_x":0.131,"bca-556-16-mid-barrel.gas_port_d":0.075,"bca-556-16-mid-barrel.gas_port_x":9.141,"bca-556-16-mid-barrel.index_pin_d":0.12525,"bca-556-16-mid-barrel.index_pin_protrusion":0.094,"bca-556-16-mid-barrel.index_pin_x":0.063,"bca-556-16-mid-barrel.journal_shoulder_x":8.846,"bca-556-16-mid-barrel.overall_length":16.501,"bca-556-16-mid-barrel.shoulder_x":14.911,"bca-556-16-mid-barrel.thread_minor_d":0.4551,"bca-556-16-mid-barrel.thread_od":0.496,"bca-556-16-mid-barrel.thread_pitch":0.03571},"profiles":{"side":[[0,0.36],[0,-0.24],[0.04,-0.307],[0.04,-0.323],[0.032,-0.331],[0.032,-0.347],[0.017,-0.38],[0.017,-0.412],[0.052,-0.474],[0.099,-0.499],[0.47,-0.503],[0.478,-0.494],[0.857,-0.499],[0.865,-0.49],[0.976,-0.492],[0.996,-0.504],[1.012,-0.537],[1.047,-0.574],[1.111,-0.591],[1.119,-0.583],[1.158,-0.583],[1.194,-0.547],[1.202,-0.515],[1.222,-0.494],[1.357,-0.496],[1.365,-0.488],[1.786,-0.492],[1.897,-0.436],[1.913,-0.436],[1.961,-0.412],[1.985,-0.413],[2.017,-0.396],[2.073,-0.389],[2.08,-0.381],[2.104,-0.381],[2.112,-0.373],[2.144,-0.373],[2.152,-0.365],[2.176,-0.365],[2.184,-0.357],[2.224,-0.358],[2.232,-0.35],[2.296,-0.35],[2.304,-0.342],[2.543,-0.345],[2.551,-0.353],[2.615,-0.354],[2.623,-0.345],[3.272,-0.352],[3.28,-0.344],[4.036,-0.352],[4.044,-0.344],[4.933,-0.353],[4.941,-0.345],[5.647,-0.352],[5.656,-0.344],[5.664,-0.352],[5.672,-0.344],[6.446,-0.352],[6.455,-0.343],[7.298,-0.352],[7.307,-0.344],[8.105,-0.352],[8.113,-0.344],[8.336,-0.346],[8.344,-0.338],[8.683,-0.341],[8.692,-0.35],[8.774,-0.35],[8.783,-0.359],[8.841,-0.359],[8.849,-0.368],[8.882,-0.368],[8.89,-0.377],[8.915,-0.377],[8.923,-0.385],[8.948,-0.386],[8.981,-0.403],[9.006,-0.403],[9.039,-0.42],[9.056,-0.42],[9.064,-0.428],[9.089,-0.429],[9.098,-0.437],[9.114,-0.437],[9.131,-0.454],[9.147,-0.454],[9.222,-0.497],[9.23,-0.489],[9.679,-0.493],[9.687,-0.485],[9.812,-0.486],[9.841,-0.449],[9.841,-0.416],[9.85,-0.407],[9.85,-0.382],[9.862,-0.361],[9.879,-0.362],[9.887,-0.37],[9.971,-0.371],[9.979,-0.379],[10.071,-0.38],[10.079,-0.372],[10.112,-0.372],[10.121,-0.381],[10.171,-0.381],[10.179,-0.373],[10.748,-0.379],[10.756,-0.37],[11.62,-0.379],[11.629,-0.371],[12.43,-0.379],[12.438,-0.371],[13.583,-0.382],[13.592,-0.374],[14.521,-0.383],[14.538,-0.375],[14.547,-0.383],[14.581,-0.384],[14.59,-0.375],[15.267,-0.382],[15.275,-0.374],[15.292,-0.374],[15.301,-0.383],[15.309,-0.374],[15.318,-0.383],[15.327,-0.374],[15.335,-0.383],[15.344,-0.375],[15.352,-0.383],[15.361,-0.375],[15.843,-0.379],[15.851,-0.371],[15.869,-0.371],[15.881,-0.359],[15.881,-0.35],[15.899,-0.333],[15.916,-0.299],[15.916,-0.282],[15.925,-0.265],[15.937,-0.253],[15.963,-0.262],[15.972,-0.253],[16.058,-0.254],[16.075,-0.263],[16.093,-0.254],[16.11,-0.263],[16.127,-0.255],[16.144,-0.263],[16.153,-0.255],[16.17,-0.255],[16.179,-0.264],[16.188,-0.255],[16.447,-0.258],[16.481,-0.241],[16.501,-0.222],[16.501,0.2],[16.481,0.219],[16.447,0.237],[16.386,0.237],[16.378,0.246],[16.36,0.237],[16.343,0.238],[16.334,0.246],[16.326,0.238],[16.308,0.238],[16.3,0.246],[16.291,0.238],[16.274,0.238],[16.265,0.247],[16.257,0.238],[16.067,0.24],[16.058,0.231],[15.989,0.232],[15.981,0.241],[15.972,0.232],[15.963,0.241],[15.929,0.241],[15.907,0.279],[15.907,0.297],[15.89,0.314],[15.89,0.322],[15.851,0.361],[15.834,0.369],[15.705,0.37],[15.696,0.362],[15.688,0.371],[15.671,0.362],[15.653,0.362],[15.645,0.371],[15.627,0.363],[15.61,0.371],[15.593,0.371],[15.576,0.363],[15.567,0.372],[15.559,0.363],[14.205,0.374],[14.196,0.366],[13.048,0.375],[13.039,0.366],[11.62,0.378],[11.612,0.369],[11.578,0.37],[11.562,0.378],[11.553,0.37],[10.488,0.378],[10.48,0.37],[10.421,0.371],[10.405,0.379],[10.396,0.371],[9.896,0.375],[9.887,0.366],[9.871,0.367],[9.854,0.358],[9.833,0.446],[9.816,0.48],[9.796,0.493],[9.504,0.495],[9.496,0.487],[9.479,0.495],[9.446,0.495],[9.438,0.487],[9.205,0.489],[9.098,0.431],[9.081,0.431],[9.073,0.423],[9.056,0.423],[9.048,0.415],[9.031,0.415],[8.998,0.399],[8.973,0.399],[8.965,0.391],[8.907,0.383],[8.899,0.374],[8.865,0.375],[8.857,0.366],[8.824,0.367],[8.816,0.358],[8.783,0.359],[8.774,0.35],[8.725,0.351],[8.716,0.343],[8.567,0.344],[8.559,0.336],[8.435,0.337],[8.427,0.345],[8.419,0.337],[8.394,0.337],[8.386,0.345],[8.237,0.347],[8.229,0.355],[8.22,0.347],[7.504,0.353],[7.496,0.344],[6.455,0.353],[6.446,0.345],[5.542,0.352],[5.534,0.344],[5.038,0.348],[5.03,0.34],[5.022,0.348],[5.014,0.34],[4.941,0.34],[4.933,0.349],[4.504,0.352],[4.496,0.344],[3.843,0.35],[3.835,0.341],[3.601,0.343],[3.593,0.352],[3.409,0.353],[3.401,0.345],[2.535,0.352],[2.527,0.344],[2.264,0.346],[2.256,0.355],[2.192,0.355],[2.184,0.363],[2.128,0.364],[2.12,0.372],[2.073,0.372],[2.065,0.381],[2.041,0.381],[2.033,0.389],[2.017,0.389],[1.985,0.406],[1.961,0.406],[1.897,0.439],[1.857,0.448],[1.778,0.489],[1.452,0.492],[1.444,0.484],[1.428,0.484],[1.42,0.492],[1.412,0.484],[1.206,0.486],[1.186,0.523],[1.186,0.539],[1.15,0.576],[1.127,0.584],[1.119,0.576],[1.032,0.577],[0.996,0.54],[0.992,0.528],[0.976,0.528],[0.937,0.496],[0.668,0.498],[0.66,0.49],[0.123,0.494],[0.115,0.486],[0.06,0.487],[0.04,0.466],[0.032,0.442],[0.009,0.41]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"x":"extension_rear_x"}}},"bounds":{"min":[-0.996,-0.5835,-0.5835],"max":[15.505,0.5876,0.5835]},"volume_in3":6.9481,"centroid":[6.5915,0.0002,0],"shell":[6.9776,0.0015,0],"area_in2":53.2349,"triangles":14522,"manifold":true,"slabs":[[-0.996,-0.497,-0.497,-0.171,0.497,0.497],[-0.171,-0.584,-0.584,0.242,0.588,0.584],[0.242,-0.49,-0.49,1.067,0.49,0.49],[1.067,-0.426,-0.426,8.08,0.426,0.426],[8.08,-0.493,-0.493,8.905,0.493,0.493],[8.905,-0.378,-0.378,15.092,0.378,0.378],[15.092,-0.248,-0.248,15.505,0.248,0.248]],"slots":["barrel","pin"]},"bca-stripped-lower":{"part":"bca-stripped-lower","model":"bca-stripped-lower.glb","script":"bca_stripped_lower.py","inputs":{"bca-stripped-lower.bolt_catch_boss_bottom_y":-0.14,"bca-stripped-lower.bolt_catch_boss_front_x":3.58,"bca-stripped-lower.bolt_catch_boss_rear_x":3.05,"bca-stripped-lower.bolt_catch_gap_front_x":3.375,"bca-stripped-lower.bolt_catch_gap_rear_x":3.203,"bca-stripped-lower.buffer_axis_above_pin":0.8775,"bca-stripped-lower.fence_bottom_y":-0.93,"bca-stripped-lower.fence_corner_r":0.07,"bca-stripped-lower.fence_front_x":3.55,"bca-stripped-lower.fence_rear_x":2.97,"bca-stripped-lower.fence_top_y":-0.19,"bca-stripped-lower.grip_mating_y":-1.045,"bca-stripped-lower.grip_seat_y":-1.0695,"bca-stripped-lower.grip_shelf_top_x":-0.03,"bca-stripped-lower.hammer_pin_x":2.771,"bca-stripped-lower.hammer_pin_y":-0.375,"bca-stripped-lower.magwell_front_x":6.1,"bca-stripped-lower.magwell_wall_curve_bottom_y_left":-1.2,"bca-stripped-lower.magwell_wall_curve_top_y_left":-0.69,"bca-stripped-lower.magwell_wall_rear_x":3.58,"bca-stripped-lower.magwell_wall_rear_x_left":3.48,"bca-stripped-lower.magwell_wall_upper_rear_x_left":2.96,"bca-stripped-lower.rear_behind_pin":1.125,"bca-stripped-lower.selector_x":0.803,"bca-stripped-lower.selector_y":-0.466,"bca-stripped-lower.tower_front_x":-0.378,"bca-stripped-lower.trigger_guard_front_x":3.3425,"bca-stripped-lower.trigger_guard_front_y":-2.18,"bca-stripped-lower.trigger_guard_rear_x":1.4985,"bca-stripped-lower.trigger_guard_rear_y":-2.18,"bca-stripped-lower.trigger_pin_x":1.928,"bca-stripped-lower.trigger_pin_y":-0.689,"bca-stripped-lower.well_roll_bottom_y":-0.204,"bca-stripped-lower.well_roll_crest_out":0.8,"bca-stripped-lower.well_roll_front_x":6.237,"bca-stripped-lower.well_roll_rear_round":0.2,"bca-stripped-lower.well_roll_rear_x":2.91,"std.ar15.bolt_catch_boss_out":0.618,"std.ar15.bolt_catch_plunger_hole_d":0.156,"std.ar15.bolt_catch_plunger_hole_depth":0.4703,"std.ar15.bolt_catch_plunger_hole_y":-0.195,"std.ar15.bolt_catch_slot_bottom_y":-0.38,"std.ar15.bolt_catch_slot_floor":0.4409,"std.ar15.bolt_catch_slot_front_x":3.375,"std.ar15.bolt_catch_slot_width":0.172,"std.ar15.bore_axis_y":0.8775,"std.ar15.buffer_tower_front_x":-0.628,"std.ar15.buffer_tower_od":1.392,"std.ar15.deck_front_x":6.194,"std.ar15.deck_y":0.2485,"std.ar15.fcg_pin_hole_d":0.15675,"std.ar15.fcg_pocket_corner_r":0.218,"std.ar15.fcg_pocket_depth":1.249,"std.ar15.fcg_pocket_front_x":3.11,"std.ar15.fcg_pocket_length":2.87,"std.ar15.fcg_pocket_width":0.69,"std.ar15.front_lug_slot_width":0.5,"std.ar15.grip_lug_depth":0.93,"std.ar15.grip_lug_face_angle":60,"std.ar15.grip_lug_face_from_pin":1.228,"std.ar15.grip_lug_front_from_rear_face":2.3,"std.ar15.grip_lug_length":1.25,"std.ar15.grip_lug_width":0.375,"std.ar15.grip_seat_below_deck":1.318,"std.ar15.lower_body_width":0.88,"std.ar15.mag_catch_boss_edge_r":0.059,"std.ar15.mag_catch_boss_proud":0.0906,"std.ar15.mag_catch_boss_r":0.253,"std.ar15.mag_catch_boss_x":4.262,"std.ar15.mag_catch_cbore_d":0.312,"std.ar15.mag_catch_cbore_depth":0.25,"std.ar15.mag_catch_fence_out":0.549,"std.ar15.mag_catch_hole_d":0.2055,"std.ar15.mag_catch_slot_bottom_y":-0.689,"std.ar15.mag_catch_slot_floor":0.3799,"std.ar15.mag_catch_slot_front_x":4.557,"std.ar15.mag_catch_slot_h":0.252,"std.ar15.mag_catch_slot_rear_x":3.048,"std.ar15.mag_catch_x":3.291,"std.ar15.mag_catch_y":-0.565,"std.ar15.mag_release_pocket_depth":0.617,"std.ar15.mag_release_pocket_h":0.515,"std.ar15.mag_release_pocket_w":0.319,"std.ar15.magwell_band_bottom_y":-1.959,"std.ar15.magwell_band_front_x":4.549,"std.ar15.magwell_band_proud":0.059,"std.ar15.magwell_band_rear_x":3.975,"std.ar15.magwell_band_side":0.084,"std.ar15.magwell_box_length":2.398,"std.ar15.magwell_corner_r":0.062,"std.ar15.magwell_front_inner_x":6.025,"std.ar15.magwell_length":2.553,"std.ar15.magwell_outside_width":1.098,"std.ar15.magwell_spine_slot_width":0.47,"std.ar15.magwell_width":0.898,"std.ar15.pin_spacing":6.375,"std.ar15.pivot_hole_d":0.251,"std.ar15.rear_lug_slot_depth":0.63,"std.ar15.rear_lug_slot_rear_x":-0.402,"std.ar15.rear_lug_slot_width":0.5,"std.ar15.rear_underside_arc_center_below_seat":0.1928,"std.ar15.rear_underside_arc_center_x":-1.0238,"std.ar15.rear_underside_arc_r":0.75,"std.ar15.rear_underside_round_r":0.44,"std.ar15.rear_wall_arc_r":0.75,"std.ar15.receiver_rear_x":-1.125,"std.ar15.safety_detent_boss_below_deck":0.455,"std.ar15.safety_detent_boss_face":0.53,"std.ar15.safety_detent_boss_from_rear":0.36,"std.ar15.safety_detent_boss_length":0.43,"std.ar15.selector_hole_d":0.376,"std.ar15.takedown_hole_d":0.251,"std.ar15.takedown_spotface_d":0.44,"std.ar15.takedown_spotface_depth":0.04,"std.ar15.trigger_guard_ear_gap":0.442,"std.ar15.trigger_guard_ears_width":0.659,"std.ar15.trigger_guard_front_hole_d":0.1265,"std.ar15.trigger_guard_front_spotface_d":0.25,"std.ar15.trigger_guard_front_spotface_floor":0.3219,"std.ar15.trigger_guard_rear_hole_d":0.1285,"std.ar15.trigger_pin_x":1.928,"std.ar15.trigger_slot_front_ahead_of_pin":0.52,"std.ar15.trigger_slot_length":0.68,"std.ar15.trigger_slot_width":0.312,"std.ar15.upper_rear_face_x":-0.621,"std.receiver_extension.milspec_od":1.148},"profiles":{"side":[[-1.17,0.828],[-1.105,-0.223],[-1.065,-0.393],[-0.728,-0.455],[-0.458,-0.62],[-0.335,-0.772],[-0.22,-1.018],[-0.03,-1.047],[-0.025,-1.317],[0.012,-1.355],[1.027,-1.93],[1.172,-1.93],[1.2,-1.958],[1.212,-2.28],[1.652,-2.285],[1.74,-2.208],[1.485,-1.962],[1.39,-1.703],[1.395,-1.533],[1.45,-1.342],[1.603,-1.15],[1.887,-1.05],[2.878,-1.05],[3.133,-1.18],[3.213,-1.19],[3.34,-1.368],[3.39,-1.698],[3.3,-1.933],[3.155,-2.097],[3.15,-2.217],[3.232,-2.305],[3.393,-2.295],[3.497,-2.33],[3.527,-2.295],[4.503,-2.15],[6.188,-1.83],[6.215,-1.743],[6.09,-1.533],[6.1,-0.572],[6.165,-0.408],[6.282,-0.275],[6.545,-0.143],[6.59,-0.062],[6.59,0.052],[6.555,0.133],[6.467,0.19],[6.188,0.205],[6.107,0.255],[5.987,0.27],[-0.018,0.265],[-0.283,0.4],[-0.475,0.633],[-0.595,0.953],[-0.58,1.232],[-0.63,1.538],[-0.658,1.565],[-0.973,1.57],[-1.083,1.54],[-1.125,1.488],[-1.155,1.353]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{}}},"bounds":{"min":[-1.125,-2.33,-0.6986],"max":[6.59,1.5735,0.8]},"volume_in3":5.1071,"centroid":[2.4329,-0.6045,0.0303],"shell":[2.8796,-0.6436,0.0095],"area_in2":76.1738,"triangles":24644,"manifold":true,"interior":{"pocket":{"x":[0.24,3.11],"z":0.345,"floor_y":-1.0005},"rear_lug_slot":{"x":[-0.402,0.458],"z":0.25,"floor_y":-0.3815},"safety_detent_boss":{"x":[0.6,1.03],"face_z":0.185,"top_y":-0.2065},"trigger_slot":{"x":[1.768,2.448],"z":0.156},"magazine_well":{"x":[3.472,6.025],"z":0.449}},"holes":{"takedown":{"x":0,"y":0,"d":0.251},"pivot":{"x":6.375,"y":0,"d":0.251},"selector":{"x":0.803,"y":-0.466,"d":0.376},"hammer":{"x":2.771,"y":-0.375,"d":0.1568},"trigger":{"x":1.928,"y":-0.689,"d":0.1568},"guard rear":{"x":1.4985,"y":-2.18,"d":0.1285},"guard front":{"x":3.3425,"y":-2.18,"d":0.1265}},"catches":{"button_pocket":{"x":3.291,"y":-0.565,"floor_z":-0.068,"face_z":0.549},"catch_slot":{"x":[3.048,4.557],"floor_z":-0.3799},"bolt_catch_slot":{"x":[3.203,3.375],"bottom_y":-0.38,"floor_z":-0.4409}},"grip_mount":{"lug":{"seat_y":-1.0695,"x":[-0.075,1.2],"width":0.375,"foot_x":1.0072,"flat_y":-1.9995},"ears":{"width":0.659,"gap":0.442,"gap_top_y":-1.9995,"rear_x":[1.2,1.8316],"front_x":[2.9162,3.48]},"rear_underside":{"round_r":0.44,"arc_r":0.75,"axis_x":-1.0238,"axis_y":-1.2623}},"rear_walls":{"r":0.75,"centre":[0.122,0.9985],"x":[-0.621,0.122],"meets_face_y":0.8963,"runs_out":[0.055,0.2515],"toe_x":[-0.1255,0.055]},"deck":{"y":0.2485,"x":[-0.02,6.188]},"slabs":[[-1.125,-0.567,-0.696,-0.739,1.573,0.696],[-0.739,-0.924,-0.696,-0.353,1.573,0.696],[-0.353,-1.437,-0.44,0.032,0.419,0.44],[0.032,-1.659,-0.44,0.418,0.254,0.44],[0.418,-1.882,-0.44,0.804,0.249,0.44],[0.804,-2,-0.44,1.19,0.249,0.44],[1.19,-2.285,-0.44,1.961,0.249,0.44],[1.961,-1.05,-0.44,2.733,0.249,0.44],[2.733,-1.172,-0.618,3.118,0.249,0.8],[3.118,-2.33,-0.618,3.89,0.249,0.8],[3.89,-2.241,-0.699,4.276,0.249,0.8],[4.276,-2.184,-0.699,4.661,0.249,0.8],[4.661,-2.12,-0.549,5.047,0.249,0.8],[5.047,-2.047,-0.549,5.433,0.249,0.8],[5.433,-1.973,-0.549,5.819,0.249,0.8],[5.819,-1.9,-0.549,6.204,0.249,0.8],[6.204,-1.778,-0.549,6.59,0.249,0.8]],"slots":["receiver"]},"bcm-115-carbine-barrel":{"part":"bcm-115-carbine-barrel","model":"bcm-115-carbine-barrel.glb","script":"bcm_115_carbine_barrel.py","inputs":{"bcm-115-carbine-barrel.bore_d":0.219,"bcm-115-carbine-barrel.chamber_od":0.981,"bcm-115-carbine-barrel.collar_chamfer":0.037,"bcm-115-carbine-barrel.collar_od":0.855,"bcm-115-carbine-barrel.collar_rear_x":6.254,"bcm-115-carbine-barrel.extension_lug_bore_d":0.572,"bcm-115-carbine-barrel.extension_lug_depth":0.214,"bcm-115-carbine-barrel.extension_mouth_chamfer":0.045,"bcm-115-carbine-barrel.extension_mouth_d":0.77,"bcm-115-carbine-barrel.extension_od":0.999,"bcm-115-carbine-barrel.extension_rear_x":-0.99,"bcm-115-carbine-barrel.extension_recess_d":0.83,"bcm-115-carbine-barrel.extension_recess_depth":0.595,"bcm-115-carbine-barrel.flange_d":1.176,"bcm-115-carbine-barrel.flange_front_x":0.114,"bcm-115-carbine-barrel.gas_port_d":0.078,"bcm-115-carbine-barrel.gas_port_x":7.138,"bcm-115-carbine-barrel.groove_front_x":6.923,"bcm-115-carbine-barrel.groove_od":0.725,"bcm-115-carbine-barrel.handguard_front_od":0.654,"bcm-115-carbine-barrel.handguard_knee_x":5.22,"bcm-115-carbine-barrel.handguard_rear_od":0.679,"bcm-115-carbine-barrel.index_pin_d":0.125,"bcm-115-carbine-barrel.index_pin_top":0.594,"bcm-115-carbine-barrel.index_pin_x":0.081,"bcm-115-carbine-barrel.journal_front_x":8.803,"bcm-115-carbine-barrel.journal_od":0.75,"bcm-115-carbine-barrel.journal_rear_x":6.878,"bcm-115-carbine-barrel.mid_od":0.726,"bcm-115-carbine-barrel.muzzle_od":0.699,"bcm-115-carbine-barrel.outline_front_face":12.258,"bcm-115-carbine-barrel.outline_inset":0.0067,"bcm-115-carbine-barrel.outline_lens_x":6.134,"bcm-115-carbine-barrel.outline_rear_face":0.046,"bcm-115-carbine-barrel.outline_yaw_run":-4310,"bcm-115-carbine-barrel.overall_length":12.001,"bcm-115-carbine-barrel.ramp_mid_od":0.713,"bcm-115-carbine-barrel.ramp_mid_x":6.017,"bcm-115-carbine-barrel.ramp_rear_x":5.777,"bcm-115-carbine-barrel.shoulder_chamfer":0.035,"bcm-115-carbine-barrel.shoulder_x":10.387,"bcm-115-carbine-barrel.step_x":9.813,"bcm-115-carbine-barrel.taper_front_x":1.631,"bcm-115-carbine-barrel.taper_rear_x":0.77,"bcm-115-carbine-barrel.thread_major_d":0.4957,"bcm-115-carbine-barrel.thread_minor_d":0.4551,"bcm-115-carbine-barrel.thread_pitch":0.03571},"profiles":{"side":[[0.046,0.499],[0.046,-0.484],[0.061,-0.493],[0.122,-0.493],[0.128,-0.499],[0.794,-0.496],[0.8,-0.502],[1.026,-0.502],[1.035,-0.511],[1.048,-0.572],[1.075,-0.593],[1.173,-0.587],[1.182,-0.577],[1.176,-0.553],[1.197,-0.55],[1.207,-0.541],[1.219,-0.504],[1.228,-0.495],[1.258,-0.495],[1.265,-0.488],[1.271,-0.495],[1.283,-0.488],[1.307,-0.488],[1.662,-0.487],[1.68,-0.493],[1.698,-0.493],[1.705,-0.487],[1.753,-0.487],[1.76,-0.493],[1.845,-0.492],[1.851,-0.486],[1.949,-0.474],[1.955,-0.468],[2.096,-0.449],[2.132,-0.436],[2.193,-0.43],[2.199,-0.424],[2.267,-0.418],[2.273,-0.411],[2.309,-0.411],[2.346,-0.399],[2.389,-0.399],[2.425,-0.386],[2.456,-0.386],[2.493,-0.374],[2.56,-0.368],[2.566,-0.362],[2.633,-0.355],[2.639,-0.349],[2.67,-0.349],[2.676,-0.343],[2.706,-0.343],[2.712,-0.337],[3.843,-0.333],[3.849,-0.339],[3.861,-0.332],[3.904,-0.332],[4.051,-0.332],[4.057,-0.338],[4.1,-0.338],[4.112,-0.332],[4.149,-0.331],[4.155,-0.338],[4.21,-0.337],[4.228,-0.331],[4.234,-0.337],[4.295,-0.337],[4.314,-0.331],[4.344,-0.331],[4.35,-0.337],[4.442,-0.336],[4.448,-0.33],[4.454,-0.336],[4.491,-0.336],[4.497,-0.33],[4.564,-0.336],[4.68,-0.336],[4.686,-0.33],[4.735,-0.329],[4.742,-0.335],[4.766,-0.335],[4.833,-0.329],[4.882,-0.335],[4.888,-0.329],[4.913,-0.329],[4.931,-0.329],[4.937,-0.335],[6.984,-0.327],[6.991,-0.333],[7.088,-0.339],[7.095,-0.345],[7.131,-0.345],[7.168,-0.357],[7.192,-0.357],[7.247,-0.375],[7.266,-0.375],[7.284,-0.387],[7.327,-0.393],[7.345,-0.406],[7.364,-0.405],[7.382,-0.418],[7.419,-0.424],[7.425,-0.43],[8.042,-0.428],[8.063,-0.4],[8.063,-0.369],[8.072,-0.36],[8.097,-0.36],[8.109,-0.378],[8.354,-0.371],[8.415,-0.371],[8.421,-0.377],[9.625,-0.373],[9.637,-0.367],[9.643,-0.373],[9.741,-0.373],[9.747,-0.366],[9.765,-0.372],[9.998,-0.372],[10.022,-0.359],[10.92,-0.356],[10.927,-0.362],[10.982,-0.362],[10.988,-0.356],[11.03,-0.356],[11.061,-0.343],[11.599,-0.341],[11.626,-0.308],[11.638,-0.247],[11.653,-0.237],[11.684,-0.237],[11.696,-0.225],[11.708,-0.225],[11.727,-0.237],[11.733,-0.225],[11.77,-0.231],[11.782,-0.219],[11.788,-0.231],[11.8,-0.231],[11.812,-0.218],[11.831,-0.237],[11.843,-0.224],[11.873,-0.23],[11.886,-0.218],[11.892,-0.23],[11.91,-0.23],[11.922,-0.218],[11.935,-0.23],[11.947,-0.23],[11.959,-0.218],[11.965,-0.23],[11.996,-0.224],[12.002,-0.23],[12.02,-0.23],[12.032,-0.218],[12.038,-0.23],[12.057,-0.23],[12.069,-0.218],[12.075,-0.23],[12.093,-0.23],[12.1,-0.217],[12.106,-0.217],[12.112,-0.23],[12.142,-0.223],[12.148,-0.229],[12.167,-0.229],[12.179,-0.223],[12.197,-0.229],[12.216,-0.217],[12.228,-0.223],[12.258,-0.18],[12.258,0.21],[12.245,0.235],[12.232,0.235],[12.214,0.254],[12.196,0.241],[12.171,0.253],[12.159,0.241],[12.141,0.253],[12.128,0.235],[12.11,0.253],[12.098,0.253],[12.086,0.241],[12.067,0.253],[12.049,0.241],[12.037,0.253],[12.025,0.253],[12.018,0.241],[12.012,0.241],[12,0.253],[11.976,0.241],[11.963,0.253],[11.951,0.253],[11.945,0.24],[11.939,0.24],[11.921,0.253],[11.908,0.234],[11.89,0.252],[11.878,0.246],[11.847,0.252],[11.835,0.24],[11.829,0.24],[11.823,0.252],[11.811,0.252],[11.792,0.24],[11.78,0.252],[11.762,0.24],[11.749,0.252],[11.725,0.24],[11.707,0.252],[11.695,0.246],[11.652,0.252],[11.636,0.267],[11.63,0.316],[11.618,0.34],[11.596,0.355],[11.046,0.353],[11.022,0.365],[10.46,0.363],[10.453,0.37],[10.417,0.369],[10.411,0.363],[10.405,0.369],[10.288,0.369],[10.062,0.362],[10.056,0.368],[10.013,0.368],[10.007,0.374],[9.952,0.374],[9.946,0.38],[9.891,0.38],[9.885,0.374],[9.867,0.374],[9.824,0.373],[9.818,0.379],[9.677,0.379],[9.665,0.373],[9.659,0.379],[9.5,0.378],[9.494,0.372],[9.451,0.372],[9.445,0.378],[8.162,0.374],[8.155,0.38],[8.137,0.373],[8.131,0.38],[8.125,0.373],[8.106,0.373],[8.088,0.361],[8.067,0.37],[8.054,0.407],[8.039,0.422],[8.021,0.428],[7.416,0.426],[7.342,0.401],[7.324,0.389],[7.306,0.389],[7.239,0.364],[7.214,0.364],[7.184,0.352],[7.159,0.352],[7.153,0.345],[7.123,0.345],[7.117,0.339],[7.08,0.339],[7.074,0.333],[7.025,0.333],[7.019,0.327],[5.998,0.323],[5.98,0.329],[5.961,0.323],[5.943,0.329],[5.913,0.323],[5.906,0.329],[5.619,0.328],[5.613,0.334],[5.595,0.328],[5.466,0.327],[5.436,0.327],[5.43,0.333],[4.446,0.33],[4.44,0.336],[3.627,0.333],[3.621,0.339],[3.608,0.333],[3.602,0.339],[2.93,0.336],[2.924,0.343],[2.698,0.342],[2.692,0.348],[2.661,0.348],[2.624,0.36],[2.588,0.36],[2.551,0.372],[2.453,0.384],[2.447,0.39],[2.423,0.39],[2.386,0.402],[2.319,0.408],[2.288,0.42],[2.221,0.426],[2.19,0.438],[2.117,0.444],[2.086,0.456],[2.056,0.456],[2.019,0.468],[1.921,0.48],[1.884,0.492],[1.835,0.491],[1.829,0.498],[1.334,0.496],[1.328,0.502],[1.206,0.501],[1.2,0.526],[1.194,0.514],[1.185,0.511],[1.181,0.532],[1.178,0.511],[1.169,0.501],[1.16,0.517],[1.166,0.523],[1.166,0.553],[1.178,0.584],[1.169,0.593],[1.065,0.593],[1.053,0.586],[1.047,0.574],[1.038,0.571],[1.035,0.501],[0.9,0.5],[0.888,0.513],[0.876,0.506],[0.858,0.506],[0.851,0.512],[0.845,0.506],[0.534,0.505],[0.485,0.505],[0.479,0.511],[0.473,0.505],[0.448,0.505],[0.442,0.511],[0.369,0.511],[0.35,0.505],[0.344,0.511],[0.057,0.51]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"x":"extension_rear_x"}}},"bounds":{"min":[-0.99,-0.588,-0.588],"max":[11.011,0.594,0.588]},"volume_in3":4.76,"centroid":[4.4209,0.0001,0],"shell":[4.476,0.0009,0],"area_in2":40.4602,"triangles":15444,"manifold":true,"slabs":[[-0.99,-0.5,-0.5,-0.216,0.5,0.5],[-0.216,-0.588,-0.588,0.171,0.594,0.588],[0.171,-0.491,-0.491,1.333,0.491,0.491],[1.333,-0.392,-0.392,1.72,0.392,0.392],[1.72,-0.349,-0.349,5.978,0.349,0.349],[5.978,-0.428,-0.428,7.14,0.428,0.428],[7.14,-0.375,-0.375,10.624,0.375,0.375],[10.624,-0.248,-0.248,11.011,0.248,0.248]],"slots":["barrel"]},"bcm-145-mid-barrel":{"part":"bcm-145-mid-barrel","model":"bcm-145-mid-barrel.glb","script":"bcm_145_mid_barrel.py","inputs":{"bcm-145-mid-barrel.bore_d":0.219,"bcm-145-mid-barrel.chamber_od":0.98,"bcm-145-mid-barrel.collar_od":0.853,"bcm-145-mid-barrel.collar_rear_x":8.204,"bcm-145-mid-barrel.extension_lug_bore_d":0.572,"bcm-145-mid-barrel.extension_lug_depth":0.214,"bcm-145-mid-barrel.extension_mouth_chamfer":0.045,"bcm-145-mid-barrel.extension_mouth_d":0.77,"bcm-145-mid-barrel.extension_od":0.999,"bcm-145-mid-barrel.extension_rear_x":-0.984,"bcm-145-mid-barrel.extension_recess_d":0.83,"bcm-145-mid-barrel.extension_recess_depth":0.595,"bcm-145-mid-barrel.flange_d":1.167,"bcm-145-mid-barrel.flange_front_x":0.102,"bcm-145-mid-barrel.gas_port_d":0.075,"bcm-145-mid-barrel.gas_port_x":9.098,"bcm-145-mid-barrel.handguard_front_od":0.651,"bcm-145-mid-barrel.handguard_rear_od":0.676,"bcm-145-mid-barrel.index_pin_d":0.125,"bcm-145-mid-barrel.index_pin_top":0.584,"bcm-145-mid-barrel.index_pin_x":0.086,"bcm-145-mid-barrel.journal_front_x":10.736,"bcm-145-mid-barrel.journal_od":0.75,"bcm-145-mid-barrel.journal_rear_x":8.812,"bcm-145-mid-barrel.mid_od":0.718,"bcm-145-mid-barrel.muzzle_od":0.7,"bcm-145-mid-barrel.outline_front_face":15.323,"bcm-145-mid-barrel.outline_inset":0.0061,"bcm-145-mid-barrel.outline_lens_x":7.707,"bcm-145-mid-barrel.outline_rear_face":0.213,"bcm-145-mid-barrel.outline_yaw_run":500,"bcm-145-mid-barrel.overall_length":15.001,"bcm-145-mid-barrel.ramp_mid_od":0.712,"bcm-145-mid-barrel.ramp_mid_x":7.977,"bcm-145-mid-barrel.ramp_rear_x":7.746,"bcm-145-mid-barrel.shoulder_x":13.403,"bcm-145-mid-barrel.step_x":12.84,"bcm-145-mid-barrel.taper_front_x":1.627,"bcm-145-mid-barrel.taper_rear_x":0.777,"bcm-145-mid-barrel.thread_major_d":0.4957,"bcm-145-mid-barrel.thread_minor_d":0.4551,"bcm-145-mid-barrel.thread_pitch":0.03571},"profiles":{"side":[[0.213,0.478],[0.213,-0.488],[0.229,-0.496],[1.058,-0.492],[1.112,-0.553],[1.158,-0.576],[1.288,-0.575],[1.296,-0.567],[1.311,-0.567],[1.342,-0.552],[1.391,-0.501],[1.403,-0.482],[1.939,-0.48],[1.947,-0.472],[2.054,-0.464],[2.062,-0.456],[2.093,-0.456],[2.1,-0.448],[2.139,-0.448],[2.146,-0.44],[2.185,-0.44],[2.192,-0.432],[2.277,-0.424],[2.284,-0.417],[2.353,-0.409],[2.361,-0.401],[2.399,-0.401],[2.407,-0.393],[2.438,-0.393],[2.445,-0.385],[2.476,-0.385],[2.484,-0.377],[2.522,-0.377],[2.53,-0.369],[2.606,-0.361],[2.614,-0.354],[2.652,-0.353],[2.66,-0.346],[2.706,-0.345],[2.713,-0.338],[2.752,-0.338],[2.759,-0.33],[5.705,-0.315],[5.712,-0.323],[5.72,-0.315],[6.165,-0.313],[6.172,-0.321],[7.246,-0.315],[7.254,-0.308],[7.384,-0.307],[7.392,-0.315],[8.312,-0.31],[8.32,-0.318],[8.964,-0.315],[8.972,-0.322],[9.026,-0.322],[9.033,-0.33],[9.072,-0.329],[9.079,-0.337],[9.11,-0.337],[9.118,-0.344],[9.148,-0.344],[9.156,-0.352],[9.187,-0.352],[9.194,-0.359],[9.233,-0.367],[9.241,-0.375],[9.279,-0.382],[9.287,-0.39],[9.325,-0.397],[9.348,-0.412],[9.455,-0.412],[9.463,-0.419],[9.985,-0.417],[9.996,-0.405],[10.004,-0.375],[10.015,-0.363],[10.291,-0.362],[10.299,-0.369],[10.514,-0.368],[10.521,-0.361],[10.537,-0.368],[11.357,-0.364],[11.365,-0.372],[11.956,-0.369],[11.971,-0.353],[12.316,-0.352],[12.324,-0.359],[13.367,-0.354],[13.374,-0.362],[13.474,-0.361],[13.482,-0.354],[13.566,-0.353],[13.574,-0.361],[14.134,-0.358],[14.149,-0.35],[14.348,-0.349],[14.356,-0.357],[14.379,-0.357],[14.387,-0.349],[14.41,-0.349],[14.418,-0.357],[14.433,-0.349],[14.471,-0.349],[14.487,-0.349],[14.494,-0.356],[14.717,-0.355],[14.751,-0.328],[14.774,-0.274],[14.8,-0.247],[14.847,-0.247],[14.854,-0.255],[14.885,-0.247],[14.893,-0.255],[14.908,-0.247],[14.923,-0.247],[14.931,-0.254],[14.939,-0.247],[15,-0.246],[15.015,-0.254],[15.031,-0.246],[15.038,-0.254],[15.054,-0.254],[15.307,-0.253],[15.323,-0.245],[15.323,0.235],[15.251,0.238],[15.243,0.246],[15.235,0.238],[15.22,0.246],[14.798,0.244],[14.779,0.263],[14.756,0.316],[14.729,0.343],[14.713,0.343],[14.706,0.35],[14.13,0.348],[14.1,0.363],[11.975,0.36],[11.944,0.383],[10.97,0.378],[10.962,0.386],[10.947,0.386],[10.94,0.378],[10.894,0.378],[10.886,0.385],[10.019,0.381],[10,0.4],[10,0.423],[9.988,0.435],[9.344,0.431],[9.298,0.408],[9.26,0.4],[9.229,0.385],[9.214,0.385],[9.206,0.377],[9.153,0.369],[9.145,0.361],[9.068,0.353],[9.061,0.346],[8.999,0.345],[8.992,0.338],[8.869,0.337],[8.861,0.329],[8.846,0.329],[8.838,0.337],[8.493,0.327],[8.485,0.335],[7.519,0.33],[7.511,0.338],[6.292,0.332],[6.284,0.34],[4.942,0.333],[4.934,0.341],[4.858,0.34],[4.85,0.332],[4.796,0.332],[4.789,0.34],[4.766,0.332],[4.75,0.332],[4.743,0.34],[4.727,0.332],[4.72,0.339],[3.101,0.331],[3.094,0.339],[2.963,0.338],[2.956,0.331],[2.771,0.33],[2.764,0.337],[2.741,0.337],[2.733,0.345],[2.687,0.345],[2.679,0.352],[2.649,0.352],[2.641,0.36],[2.61,0.36],[2.603,0.367],[2.564,0.367],[2.557,0.375],[2.526,0.375],[2.518,0.382],[2.487,0.382],[2.48,0.39],[2.411,0.397],[2.403,0.405],[2.365,0.405],[2.357,0.412],[2.319,0.412],[2.311,0.42],[2.273,0.419],[2.265,0.427],[2.226,0.427],[2.219,0.434],[2.188,0.434],[2.18,0.442],[2.119,0.449],[2.111,0.457],[2.073,0.457],[2.065,0.464],[2.035,0.464],[2.027,0.472],[1.996,0.472],[1.988,0.479],[1.889,0.479],[1.881,0.486],[1.843,0.486],[1.666,0.485],[1.659,0.478],[1.413,0.477],[1.398,0.484],[1.344,0.545],[1.305,0.568],[1.275,0.568],[1.267,0.575],[1.221,0.575],[1.213,0.568],[1.206,0.575],[1.19,0.575],[1.183,0.567],[1.152,0.567],[1.144,0.56],[1.129,0.559],[1.091,0.521],[1.083,0.521],[1.079,0.509],[1.053,0.482],[1.037,0.482],[1.03,0.49],[0.884,0.489],[0.224,0.486]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"x":"extension_rear_x"}}},"bounds":{"min":[-0.984,-0.5835,-0.5835],"max":[14.017,0.584,0.5835]},"volume_in3":5.7219,"centroid":[5.9143,0.0001,0],"shell":[5.9697,0.0007,0],"area_in2":48.888,"triangles":14376,"manifold":true,"slabs":[[-0.984,-0.5,-0.5,-0.194,0.5,0.5],[-0.194,-0.584,-0.584,0.2,0.584,0.584],[0.2,-0.49,-0.49,1.385,0.49,0.49],[1.385,-0.381,-0.381,4.937,0.381,0.381],[4.937,-0.331,-0.331,7.701,0.331,0.331],[7.701,-0.426,-0.426,8.885,0.426,0.426],[8.885,-0.375,-0.375,13.622,0.375,0.375],[13.622,-0.248,-0.248,14.017,0.248,0.248]],"slots":["barrel"]},"bcm-16-mid-barrel":{"part":"bcm-16-mid-barrel","model":"bcm-16-mid-barrel.glb","script":"bcm_16_mid_barrel.py","inputs":{"bcm-16-mid-barrel.bore_d":0.219,"bcm-16-mid-barrel.extension_lug_bore_d":0.572,"bcm-16-mid-barrel.extension_lug_depth":0.214,"bcm-16-mid-barrel.extension_mouth_chamfer":0.045,"bcm-16-mid-barrel.extension_mouth_d":0.77,"bcm-16-mid-barrel.extension_rear_x":-0.984,"bcm-16-mid-barrel.extension_recess_d":0.83,"bcm-16-mid-barrel.extension_recess_depth":0.595,"bcm-16-mid-barrel.flange_front_x":0.095,"bcm-16-mid-barrel.gas_port_d":0.075,"bcm-16-mid-barrel.gas_port_x":9.13,"bcm-16-mid-barrel.index_pin_d":0.125,"bcm-16-mid-barrel.index_pin_top":0.584,"bcm-16-mid-barrel.index_pin_x":0.113,"bcm-16-mid-barrel.outline_front_face":17.005,"bcm-16-mid-barrel.outline_rear_face":0.112,"bcm-16-mid-barrel.overall_length":16.501,"bcm-16-mid-barrel.shoulder_x":15.014,"bcm-16-mid-barrel.thread_major_d":0.4957,"bcm-16-mid-barrel.thread_minor_d":0.4551,"bcm-16-mid-barrel.thread_pitch":0.03571},"profiles":{"side":[[0.112,0.503],[0.112,-0.487],[0.117,-0.504],[1.05,-0.502],[1.081,-0.567],[1.101,-0.588],[1.231,-0.593],[1.262,-0.565],[1.291,-0.497],[1.909,-0.493],[2.75,-0.34],[9.074,-0.326],[9.163,-0.334],[9.292,-0.357],[9.407,-0.387],[9.529,-0.429],[9.706,-0.43],[10.147,-0.426],[10.16,-0.405],[10.173,-0.359],[10.18,-0.359],[10.195,-0.374],[11.797,-0.374],[12.079,-0.372],[12.094,-0.357],[12.319,-0.355],[14.951,-0.357],[15.191,-0.352],[15.872,-0.352],[15.902,-0.341],[16.42,-0.341],[16.457,-0.33],[16.477,-0.31],[16.504,-0.262],[16.507,-0.244],[16.517,-0.238],[16.927,-0.241],[17.005,-0.234],[17.005,0.243],[16.586,0.239],[16.512,0.243],[16.492,0.293],[16.474,0.319],[16.454,0.336],[16.428,0.343],[15.895,0.347],[15.877,0.354],[14.707,0.362],[14.393,0.357],[14.112,0.362],[13.801,0.357],[13.412,0.363],[13.068,0.358],[12.102,0.361],[12.076,0.376],[11.732,0.378],[10.544,0.375],[10.204,0.381],[10.174,0.366],[10.165,0.375],[10.154,0.42],[10.137,0.429],[9.538,0.433],[9.508,0.43],[9.367,0.379],[9.278,0.357],[9.175,0.339],[9.056,0.329],[2.773,0.341],[1.893,0.499],[1.29,0.499],[1.281,0.504],[1.266,0.545],[1.248,0.564],[1.251,0.571],[1.227,0.592],[1.109,0.592],[1.081,0.572],[1.077,0.539],[1.059,0.535],[1.057,0.504],[0.694,0.506]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"x":"extension_rear_x"}}},"bounds":{"min":[-0.984,-0.5922,-0.5922],"max":[15.517,0.5922,0.5922]},"volume_in3":6.3435,"centroid":[6.6215,0,0],"shell":[6.6764,0.0006,0],"area_in2":53.3608,"triangles":35834,"manifold":true,"slabs":[[-0.984,-0.504,-0.504,-0.571,0.504,0.504],[-0.571,-0.504,-0.504,-0.159,0.584,0.504],[-0.159,-0.592,-0.592,0.254,0.592,0.592],[0.254,-0.498,-0.498,1.079,0.498,0.498],[1.079,-0.438,-0.438,1.491,0.438,0.438],[1.491,-0.431,-0.431,8.917,0.431,0.431],[8.917,-0.377,-0.377,15.104,0.377,0.377],[15.104,-0.248,-0.248,15.517,0.248,0.248]],"slots":["barrel"]},"bcm-625-gas-block":{"part":"bcm-625-gas-block","model":"bcm-625-gas-block.glb","script":"bcm_625_gas_block.py","inputs":{"bcm-625-gas-block.height_above_bore":0.789,"bcm-625-gas-block.journal_id":0.625,"bcm-625-gas-block.length":1.011,"bcm-625-gas-block.pin_hole_d":0.078,"bcm-625-gas-block.pin_hole_from_front":0.317,"bcm-625-gas-block.pin_to_port":0.418,"bcm-625-gas-block.port_from_rear":0.276,"bcm-625-gas-block.star_center_above_bore":0.553,"bcm-625-gas-block.star_radius":0.1125,"bcm-625-gas-block.tab_below_bore":0.551,"bcm-625-gas-block.tube_hole_above_bore":0.625,"bcm-625-gas-block.tube_hole_d":0.1805,"bcm-625-gas-block.tube_hole_past_pin":0.217},"profiles":{"front":[[-0.427,0.03],[-0.417,-0.09],[-0.383,-0.193],[-0.361,-0.237],[-0.148,-0.552],[0.147,-0.552],[0.371,-0.218],[0.408,-0.127],[0.427,-0.019],[0.418,0.101],[0.397,0.176],[0.376,0.22],[0.331,0.291],[0.169,0.475],[0.141,0.548],[0.126,0.663],[0.099,0.73],[0.073,0.76],[0.051,0.774],[0.002,0.789],[-0.045,0.778],[-0.073,0.76],[-0.099,0.73],[-0.126,0.663],[-0.132,0.585],[-0.161,0.492],[-0.196,0.44],[-0.304,0.322],[-0.359,0.248],[-0.398,0.172],[-0.418,0.101]]},"features":{"front":{}},"placement":{"front":{"plane":"zy","offset":{}}},"bounds":{"min":[-0.276,-0.552,-0.4252],"max":[0.737,0.7885,0.4252]},"volume_in3":0.4234,"centroid":[0.2321,0.0398,0],"shell":[0.2315,0.0969,0],"area_in2":6.8845,"triangles":3774,"manifold":true,"slabs":[[-0.276,-0.552,-0.371,0.735,-0.217,0.371],[-0.276,-0.217,-0.425,0.735,0.453,0.425],[-0.276,0.453,-0.188,0.737,0.789,0.188]],"slots":["body","bore","marking"]},"bcm-750-gas-block":{"part":"bcm-750-gas-block","model":"bcm-750-gas-block.glb","script":"bcm_750_gas_block.py","inputs":{"bcm-750-gas-block.height_above_bore":0.785,"bcm-750-gas-block.journal_id":0.75,"bcm-750-gas-block.length":1.008,"bcm-750-gas-block.pin_hole_d":0.078,"bcm-750-gas-block.pin_hole_from_front":0.315,"bcm-750-gas-block.pin_to_port":0.418,"bcm-750-gas-block.port_from_rear":0.275,"bcm-750-gas-block.star_center_above_bore":0.552,"bcm-750-gas-block.star_radius":0.115,"bcm-750-gas-block.tab_below_bore":0.555,"bcm-750-gas-block.tube_hole_above_bore":0.625,"bcm-750-gas-block.tube_hole_d":0.1805,"bcm-750-gas-block.tube_hole_past_pin":0.217},"profiles":{"front":[[-0.432,-0.022],[-0.418,-0.13],[-0.39,-0.203],[-0.363,-0.252],[-0.147,-0.556],[0.15,-0.556],[0.396,-0.221],[0.433,-0.115],[0.448,0.03],[0.447,0.11],[0.434,0.171],[0.394,0.235],[0.344,0.298],[0.276,0.355],[0.221,0.416],[0.2,0.444],[0.167,0.515],[0.155,0.585],[0.154,0.689],[0.144,0.725],[0.123,0.752],[0.09,0.774],[0.065,0.786],[0.038,0.79],[-0.03,0.776],[-0.065,0.759],[-0.092,0.73],[-0.12,0.675],[-0.135,0.563],[-0.159,0.476],[-0.205,0.397],[-0.291,0.309],[-0.329,0.264],[-0.356,0.219],[-0.404,0.117],[-0.428,0.019]]},"features":{"front":{}},"placement":{"front":{"plane":"zy","offset":{}}},"bounds":{"min":[-0.275,-0.556,-0.4375],"max":[0.735,0.7822,0.4375]},"volume_in3":0.3097,"centroid":[0.2324,0.051,0],"shell":[0.2312,0.0943,0],"area_in2":7.0934,"triangles":3814,"manifold":true,"slabs":[[-0.275,-0.556,-0.387,0.733,-0.221,0.387],[-0.275,-0.221,-0.437,0.733,0.448,0.437],[-0.275,0.448,-0.188,0.735,0.782,0.188]],"slots":["body","bore","marking"]},"bcm-bcg":{"part":"bcm-bcg","model":"bcm-bcg.glb","script":"mil_spec_bolt_carrier_groups.py","inputs":{"bcm-bcg.length":6.672,"bcm-bcg.od":0.994,"std.ar15.carrier_body_od":0.93,"std.ar15.carrier_bolt_body_d":0.528,"std.ar15.carrier_bolt_cam_hole_to_face":1.305,"std.ar15.carrier_bolt_face_from_rear":2.675,"std.ar15.carrier_bolt_face_recess_d":0.38,"std.ar15.carrier_bolt_head_d":0.55,"std.ar15.carrier_bolt_length":2.8,"std.ar15.carrier_bolt_lug_length":0.278,"std.ar15.carrier_bolt_lug_od":0.743,"std.ar15.carrier_bolt_lug_offset":67.5,"std.ar15.carrier_bolt_lug_pitch":45,"std.ar15.carrier_bolt_lug_root_d":0.53,"std.ar15.carrier_bolt_lug_slot_width":0.102,"std.ar15.carrier_bolt_lugs":7,"std.ar15.carrier_bottom_cut_depth":0.215,"std.ar15.carrier_bottom_cut_rear":5.0965,"std.ar15.carrier_bottom_cut_rear_r":0.125,"std.ar15.carrier_cam_advance":0.255,"std.ar15.carrier_cam_advance_20":0.195,"std.ar15.carrier_cam_angle":22.5,"std.ar15.carrier_cam_dwell":0.042,"std.ar15.carrier_cam_pin_d":0.3105,"std.ar15.carrier_cam_pin_head_corner_d":0.47,"std.ar15.carrier_cam_pin_head_height":0.095,"std.ar15.carrier_cam_pin_head_length":0.32,"std.ar15.carrier_cam_pin_head_width":0.401,"std.ar15.carrier_cam_pin_hole_to_head":0.507,"std.ar15.carrier_cam_tail":0.07,"std.ar15.carrier_cam_width":0.3165,"std.ar15.carrier_cam_x":0.64,"std.ar15.carrier_cut_corner_r":0.12,"std.ar15.carrier_front_chamfer":0.075,"std.ar15.carrier_front_chamfer_angle":45,"std.ar15.carrier_front_flat_drop":0.095,"std.ar15.carrier_groove_angle":45,"std.ar15.carrier_groove_r":0.078,"std.ar15.carrier_groove_runout_from_shoulder":2.35,"std.ar15.carrier_groove_runout_r":1.5,"std.ar15.carrier_key_base_height":0.241,"std.ar15.carrier_key_bore_d":0.1805,"std.ar15.carrier_key_bore_depth":0.82,"std.ar15.carrier_key_cbore_d":0.273,"std.ar15.carrier_key_foot_length":1.31,"std.ar15.carrier_key_length":2.465,"std.ar15.carrier_key_mouth_angle":60,"std.ar15.carrier_key_mouth_d":0.225,"std.ar15.carrier_key_ramp_angle":45,"std.ar15.carrier_key_ramp_top":1.26,"std.ar15.carrier_key_screw_from_front":1.765,"std.ar15.carrier_key_screw_head_d":0.266,"std.ar15.carrier_key_screw_head_h":0.159,"std.ar15.carrier_key_screw_socket":0.125,"std.ar15.carrier_key_screw_socket_depth":0.077,"std.ar15.carrier_key_screw_spacing":0.5,"std.ar15.carrier_key_screw_x":2.055,"std.ar15.carrier_key_seat_front":1.37,"std.ar15.carrier_key_seat_rear":2.74,"std.ar15.carrier_key_seat_runout_r":0.5,"std.ar15.carrier_key_seat_y":0.42,"std.ar15.carrier_key_slot_width":0.4035,"std.ar15.carrier_key_step":0.03,"std.ar15.carrier_key_step_height":0.182,"std.ar15.carrier_key_tube_axis_y":0.361,"std.ar15.carrier_key_tube_d":0.25,"std.ar15.carrier_key_tube_length":0.9,"std.ar15.carrier_key_width":0.4005,"std.ar15.carrier_length":6.672,"std.ar15.carrier_pad_edge_angle":55,"std.ar15.carrier_pad_front":0.38,"std.ar15.carrier_rail_od":0.994,"std.ar15.carrier_rail_top_drop":0.67,"std.ar15.carrier_rear_chamfer":0.03,"std.ar15.carrier_rear_chamfer_angle":30,"std.ar15.carrier_relief_angle":75,"std.ar15.carrier_retaining_pin_csk_angle":82,"std.ar15.carrier_retaining_pin_csk_d":0.281,"std.ar15.carrier_retaining_pin_hole_d":0.093,"std.ar15.carrier_retaining_pin_x":2.536,"std.ar15.carrier_retaining_pin_y":0.157,"std.ar15.carrier_rib_bottom_drop":0.859,"std.ar15.carrier_rib_chamfer_across":0.87,"std.ar15.carrier_rib_chamfer_angle":22.5,"std.ar15.carrier_rib_rear":2.81,"std.ar15.carrier_rib_taper_angle":4.5,"std.ar15.carrier_rib_taper_start":1.8,"std.ar15.carrier_rib_width":0.399,"std.ar15.carrier_scallop_across":0.8125,"std.ar15.carrier_scallop_angle":22.5,"std.ar15.carrier_scallop_flat":0.375,"std.ar15.carrier_scallop_r":0.47,"std.ar15.carrier_scallop_rear":1.5,"std.ar15.carrier_serration_count":28,"std.ar15.carrier_serration_cutter_r":0.3125,"std.ar15.carrier_serration_depth":0.042,"std.ar15.carrier_serration_face_angle":70.5,"std.ar15.carrier_serration_flank_angle":22.25,"std.ar15.carrier_serration_front":1.9,"std.ar15.carrier_serration_pitch":0.125,"std.ar15.carrier_side_hole_d":0.125,"std.ar15.carrier_side_hole_x":2.15,"std.ar15.carrier_slab_height":0.5,"std.ar15.carrier_slot_travel":1.75,"std.ar15.carrier_slot_width":0.5,"std.ar15.carrier_tail_bore":0.625,"std.ar15.carrier_tail_front":5.1,"std.ar15.carrier_tail_notch_depth":0.1,"std.ar15.carrier_tail_notch_width":0.156,"std.ar15.carrier_top_cut_length":2.07,"std.ar15.carrier_vent_angle":45,"std.ar15.carrier_vent_d":0.109,"std.ar15.carrier_vent_x":1.34},"profiles":{},"bounds":{"min":[0,-0.4583,-0.4659],"max":[7.462,0.906,0.4659]},"volume_in3":2.9018,"centroid":[4.1793,0.0669,-0.0073],"shell":[3.7848,0.0999,0.0007],"area_in2":33.6114,"triangles":20152,"manifold":true,"slabs":[[0,-0.458,-0.465,1.964,0.465,0.465],[1.964,-0.25,-0.465,3.535,0.252,0.465],[3.535,-0.349,-0.466,4.713,0.661,0.466],[4.713,-0.362,-0.466,6.677,0.906,0.466],[6.677,-0.275,-0.275,7.069,0.275,0.275],[7.069,-0.368,-0.368,7.462,0.368,0.368]],"slots":["body","screws"]},"bcm-carbine-action-spring":{"part":"bcm-carbine-action-spring","model":"bcm-carbine-action-spring.glb","script":"bcm_carbine_action_spring.py","inputs":{"bcm-carbine-action-spring.coils":38.5,"bcm-carbine-action-spring.free_length":10.7,"bcm-carbine-action-spring.installed_length":6.972,"bcm-carbine-action-spring.od":0.94,"bcm-carbine-action-spring.wire_d":0.072,"std.carbine_buffer.head_thickness":0.254,"std.carbine_buffer.pilot_d":0.781,"std.receiver_extension.bore_d":1},"profiles":{},"bounds":{"min":[0.254,-0.4719,-0.4719],"max":[7.226,0.4719,0.4719]},"volume_in3":0.4257,"centroid":[3.74,0,0.0036],"shell":[3.74,0,0.0036],"area_in2":24.3234,"triangles":17260,"manifold":true,"slabs":[[0.254,-0.472,-0.472,7.226,0.472,0.472]],"slots":["spring"]},"bcm-carbine-buffer":{"part":"bcm-carbine-buffer","model":"bcm-carbine-buffer.glb","script":"bcm_carbine_buffer.py","inputs":{"bcm-carbine-buffer.length":3.251,"bcm-carbine-buffer.od":0.98,"std.carbine_buffer.body_d":0.687,"std.carbine_buffer.body_length":2.854,"std.carbine_buffer.body_start":0.5145,"std.carbine_buffer.bumper_band":0.06,"std.carbine_buffer.bumper_d":0.687,"std.carbine_buffer.bumper_exposed":0.4,"std.carbine_buffer.bumper_taper":13.5,"std.carbine_buffer.head_d":0.98,"std.carbine_buffer.head_flat_across":0.952,"std.carbine_buffer.head_rim":0.214,"std.carbine_buffer.head_thickness":0.254,"std.carbine_buffer.length":3.251,"std.carbine_buffer.pilot_d":0.781,"std.carbine_buffer.pilot_end":0.468,"std.carbine_buffer.pin_d":0.122,"std.carbine_buffer.pin_from_open_end":0.24},"profiles":{},"bounds":{"min":[0,-0.49,-0.49],"max":[3.251,0.462,0.49]},"volume_in3":1.2939,"centroid":[1.4641,0,0],"shell":[1.5949,0,0],"area_in2":9.6585,"triangles":7276,"manifold":true,"slabs":[[0,-0.49,-0.49,0.361,0.462,0.49],[0.361,-0.391,-0.391,3.251,0.391,0.391]],"slots":["body","bumper","pin"]},"bcm-castle-nut":{"part":"bcm-castle-nut","model":"bcm-castle-nut.glb","script":"bcm_castle_nut.py","inputs":{"bcm-castle-nut.notch_depth":0.11,"bcm-castle-nut.notch_width":0.16,"bcm-castle-nut.notches":4,"bcm-castle-nut.od":1.3748031496062993,"bcm-castle-nut.staking_notch_depth":0.082,"bcm-castle-nut.staking_notch_radial":0.075,"bcm-castle-nut.staking_notch_width":0.09,"bcm-castle-nut.staking_notches":3,"bcm-castle-nut.thickness":0.41338582677165353,"std.receiver_extension.thread_major_d":1.1813},"profiles":{},"bounds":{"min":[0,-0.6874,-0.6874],"max":[0.4134,0.6874,0.6874]},"volume_in3":0.152,"centroid":[0.2017,0,0],"shell":[0.2019,0,0],"area_in2":4.0756,"triangles":3190,"manifold":true,"slabs":[[0,-0.687,-0.595,0.413,-0.344,0.595],[0,-0.344,-0.687,0.413,0.344,0.687],[0,0.344,-0.595,0.413,0.687,0.595]],"slots":["nut"]},"bcm-delta-ring-assembly":{"part":"bcm-delta-ring-assembly","model":"bcm-delta-ring-assembly.glb","script":"bcm_delta_ring_assembly.py","inputs":{"bcm-delta-ring-assembly.length":0.6,"bcm-delta-ring-assembly.outside_diameter":2.1,"std.ar15.barrel_nut_groove":0.126,"std.ar15.barrel_nut_groove_d":1.333,"std.ar15.barrel_nut_groove_width":0.045,"std.ar15.barrel_nut_rear_x":-0.394,"std.ar15.slip_ring_bore_d":1.75,"std.ar15.slip_ring_bore_depth":0.42,"std.ar15.slip_ring_chamfer":0.02,"std.ar15.slip_ring_front_od":1.92,"std.ar15.slip_ring_land":0.086,"std.ar15.slip_ring_length":0.6,"std.ar15.slip_ring_lip_hole_d":1.38,"std.ar15.slip_ring_notch_reach":0.875,"std.ar15.slip_ring_notch_width":0.203,"std.ar15.slip_ring_od":2.1,"std.ar15.slip_ring_rear_x":-0.144,"std.ar15.slip_ring_retainer_back_start":127.6,"std.ar15.slip_ring_retainer_gap":0.2,"std.ar15.slip_ring_retainer_hole_apart":0.457,"std.ar15.slip_ring_retainer_hole_d":0.1,"std.ar15.slip_ring_retainer_hole_pcd":1.521,"std.ar15.slip_ring_retainer_id":1.372,"std.ar15.slip_ring_retainer_lug_end":42,"std.ar15.slip_ring_retainer_od":1.671,"std.ar15.slip_ring_retainer_waist_at":73.4,"std.ar15.slip_ring_retainer_waist_d":1.503,"std.ar15.slip_ring_skirt_d":1.75,"std.ar15.slip_ring_skirt_length":0.12,"std.ar15.slip_ring_spring_gap":0.245,"std.ar15.slip_ring_spring_height":0.552,"std.ar15.slip_ring_spring_id":1.41,"std.ar15.slip_ring_spring_od":1.73,"std.ar15.slip_ring_spring_sections":4,"std.ar15.slip_ring_spring_strip":0.02,"std.ar15.slip_ring_spring_wave":0.138,"std.ar15.slip_ring_step":0.015,"std.ar15.slip_ring_steps":6},"profiles":{},"bounds":{"min":[-0.268,-1.05,-1.05],"max":[0.456,1.05,1.05]},"volume_in3":0.6033,"centroid":[0.1037,-0.01,0],"shell":[0.0761,-0.0188,0],"area_in2":19.3487,"triangles":17740,"manifold":true,"slabs":[[-0.268,-1.05,-0.782,0.456,-0.7,0.782],[-0.268,-0.7,-0.99,0.456,-0.35,0.99],[-0.268,-0.35,-1.05,0.456,0.35,1.05],[-0.268,0.35,-0.99,0.456,0.7,0.99],[-0.268,0.7,-0.782,0.456,1.05,0.782]],"slots":["ring","spring"]},"bcm-end-plate":{"part":"bcm-end-plate","model":"bcm-end-plate.glb","script":"bcm_end_plate.py","inputs":{"bcm-end-plate.boss_below_axis":0.9974,"bcm-end-plate.boss_height":0.375,"bcm-end-plate.boss_proud":0.0645,"bcm-end-plate.boss_width":0.496,"bcm-end-plate.dimple_depth":0.063,"bcm-end-plate.thickness":0.13,"bcm-end-plate.top_above_axis":0.69,"std.receiver_extension.key_slot_floor":0.55,"std.receiver_extension.key_slot_width":0.125,"std.receiver_extension.thread_major_d":1.1813},"profiles":{"face":[[-0.661,-0.71],[-0.64,-0.829],[-0.556,-1.024],[-0.42,-1.669],[-0.379,-1.784],[-0.304,-1.884],[-0.202,-1.961],[-0.108,-1.996],[0.017,-2.006],[0.115,-1.985],[0.216,-1.936],[0.319,-1.837],[0.368,-1.75],[0.549,-1.034],[0.637,-0.839],[0.661,-0.64],[0.651,-0.536],[0.602,-0.389],[0.522,-0.256],[0.447,-0.174],[0.356,-0.105],[0.248,-0.049],[0.115,-0.01],[0,-0.003],[-0.007,0],[-0.154,-0.017],[-0.258,-0.052],[-0.387,-0.126],[-0.476,-0.201],[-0.56,-0.309],[-0.616,-0.417],[-0.651,-0.532]]},"features":{"face":{}},"placement":{"face":{"plane":"zy","offset":{"y":"top_above_axis"}}},"bounds":{"min":[-0.0645,-1.316,-0.661],"max":[0.13,0.69,0.661]},"volume_in3":0.1121,"centroid":[0.0533,-0.5552,-0.0104],"shell":[0.0566,-0.4317,-0.0071],"area_in2":3.064,"triangles":2296,"manifold":true,"slabs":[[-0.064,-1.316,-0.419,0.13,-0.982,0.388],[-0.064,-0.982,-0.49,0.13,-0.647,0.472],[0,-0.647,-0.565,0.13,-0.313,0.563],[0,-0.313,-0.661,0.13,0.356,0.661],[0,0.356,-0.573,0.13,0.69,0.569]],"slots":["plate"]},"bcm-front-sight-base-f-750":{"part":"bcm-front-sight-base-f-750","model":"bcm-front-sight-base-f-750.glb","script":"bcm_front_sight_base_f_750.py","inputs":{"bcm-front-sight-base-f-750.boss_half":0.155,"bcm-front-sight-base-f-750.boss_round_r":0.149,"bcm-front-sight-base-f-750.boss_top":0.834,"bcm-front-sight-base-f-750.detent_ahead_of_post":0.203,"bcm-front-sight-base-f-750.detent_hole_d":0.171,"bcm-front-sight-base-f-750.detent_hole_depth":0.511,"bcm-front-sight-base-f-750.edge_break":0.01,"bcm-front-sight-base-f-750.front_ring_foot":0.475,"bcm-front-sight-base-f-750.front_taper_pin_from_front":0.229,"bcm-front-sight-base-f-750.height_above_bore":2.615,"bcm-front-sight-base-f-750.journal_id":0.75,"bcm-front-sight-base-f-750.length":1.804,"bcm-front-sight-base-f-750.lug_bar_half":0.2215,"bcm-front-sight-base-f-750.lug_bar_top":0.67,"bcm-front-sight-base-f-750.lug_from_front":0.375,"bcm-front-sight-base-f-750.lug_stem_half":0.137,"bcm-front-sight-base-f-750.pin_hole_d":0.078,"bcm-front-sight-base-f-750.pin_hole_from_rear":0.688,"bcm-front-sight-base-f-750.port_from_rear":0.27,"bcm-front-sight-base-f-750.post_counterbore_d":0.375,"bcm-front-sight-base-f-750.post_counterbore_depth":0.227,"bcm-front-sight-base-f-750.post_from_rear":1.45,"bcm-front-sight-base-f-750.post_hole_d":0.164,"bcm-front-sight-base-f-750.post_hole_depth":0.738,"bcm-front-sight-base-f-750.post_seat_above_bore":2.325,"bcm-front-sight-base-f-750.rear_ring_foot":0.509,"bcm-front-sight-base-f-750.rear_ring_length":0.44,"bcm-front-sight-base-f-750.ring_flat_half":0.375,"bcm-front-sight-base-f-750.ring_flat_top":0.23,"bcm-front-sight-base-f-750.ring_r":0.44,"bcm-front-sight-base-f-750.slot_half":0.156,"bcm-front-sight-base-f-750.swivel_ear_half":0.222,"bcm-front-sight-base-f-750.swivel_gap_half":0.1195,"bcm-front-sight-base-f-750.swivel_hole_below_bore":0.653,"bcm-front-sight-base-f-750.swivel_hole_d":0.129,"bcm-front-sight-base-f-750.swivel_hole_from_rear":0.223,"bcm-front-sight-base-f-750.taper_pin_below_bore":0.347,"bcm-front-sight-base-f-750.taper_pin_big_d":0.1419,"bcm-front-sight-base-f-750.taper_pin_from_rear":0.2065,"bcm-front-sight-base-f-750.taper_pin_length":0.845,"bcm-front-sight-base-f-750.taper_pin_small_d":0.1251,"bcm-front-sight-base-f-750.tower_foot_half":0.4384,"bcm-front-sight-base-f-750.tower_foot_y":0.038,"bcm-front-sight-base-f-750.tower_side_top_below_seat":0.005,"bcm-front-sight-base-f-750.tower_top_half":0.239,"bcm-front-sight-base-f-750.tube_hole_above_bore":0.625,"bcm-front-sight-base-f-750.tube_hole_d":0.1805,"bcm-front-sight-base-f-750.tube_hole_depth":0.905,"bcm-front-sight-base-f-750.wing_arc_above_seat":0.0507,"bcm-front-sight-base-f-750.wing_arc_centre_half":0.8842,"bcm-front-sight-base-f-750.wing_inner_r":0.7282,"bcm-front-sight-base-f-750.wing_outer_r":0.6476},"profiles":{"side":[[-0.27,0.914],[-0.27,-0.125],[-0.266,-0.419],[-0.239,-0.49],[-0.219,-0.51],[-0.211,-0.529],[-0.208,-0.682],[-0.192,-0.747],[-0.158,-0.793],[-0.1,-0.828],[-0.065,-0.836],[-0.027,-0.836],[0.028,-0.823],[0.077,-0.793],[0.106,-0.761],[0.125,-0.728],[0.136,-0.687],[0.139,-0.63],[0.136,-0.488],[0.15,-0.474],[0.144,-0.452],[0.185,-0.395],[0.199,-0.365],[0.185,0.368],[0.188,0.415],[0.202,0.456],[0.23,0.474],[0.843,0.471],[0.884,0.479],[0.974,0.479],[1.004,0.471],[1.028,0.45],[1.06,0.365],[1.066,-0.187],[1.058,-0.351],[1.066,-0.378],[1.081,-0.396],[1.149,-0.421],[1.175,-0.455],[1.181,-0.829],[1.186,-0.857],[1.192,-0.87],[1.204,-0.877],[1.447,-0.877],[1.465,-0.87],[1.46,-0.775],[1.469,-0.752],[1.805,-0.743],[1.856,-0.693],[1.856,-0.54],[1.853,-0.444],[1.844,-0.434],[1.734,-0.391],[1.611,-0.33],[1.557,-0.325],[1.542,-0.302],[1.528,-0.231],[1.503,0.108],[1.52,0.338],[1.542,0.396],[1.531,0.792],[1.533,0.877],[1.528,0.934],[1.531,1.019],[1.525,1.046],[1.514,2.288],[1.501,2.307],[1.487,2.375],[1.457,2.444],[1.387,2.527],[1.335,2.565],[1.28,2.593],[1.207,2.612],[1.136,2.615],[1.029,2.59],[0.963,2.552],[0.913,2.507],[0.776,2.321],[0.747,2.292],[0.731,2.286],[0.702,2.255],[0.56,2.055],[0.336,1.763],[-0.247,0.978]]},"features":{"side":{"window":[[[-0.009,0.901],[-0.009,0.932],[0.008,0.97],[0.207,1.235],[0.306,1.347],[0.399,1.489],[0.687,1.871],[0.693,1.868],[0.731,1.887],[0.92,1.89],[0.955,1.885],[1.004,1.863],[1.03,1.834],[1.049,1.787],[1.049,1.547],[1.069,1.489],[1.103,1.45],[1.133,1.431],[1.179,1.414],[1.242,1.403],[1.282,1.369],[1.315,1.309],[1.32,1.262],[1.317,1.107],[1.323,0.948],[1.317,0.904],[1.301,0.863],[1.28,0.84],[1.25,0.821],[1.215,0.81],[1.174,0.807],[0.217,0.796],[0.099,0.799],[0.069,0.807],[0.036,0.826],[0.005,0.863]]]}},"placement":{"side":{"plane":"xy","offset":{}}},"bounds":{"min":[-0.27,-0.877,-0.4399],"max":[1.856,2.615,0.4399]},"volume_in3":1.218,"centroid":[0.8005,0.8213,0.0003],"shell":[0.7741,0.6856,0.0004],"area_in2":20.7564,"triangles":13306,"manifold":true,"slabs":[[-0.239,-0.877,-0.375,1.856,-0.489,0.375],[-0.27,-0.489,-0.428,1.854,-0.101,0.428],[-0.27,-0.101,-0.44,1.542,0.675,0.44],[-0.27,0.675,-0.383,1.534,1.063,0.383],[-0.184,1.063,-0.349,1.525,1.451,0.349],[0.104,1.451,-0.315,1.521,1.839,0.315],[0.394,1.839,-0.281,1.518,2.227,0.281],[0.682,2.227,-0.283,1.515,2.615,0.283]],"slots":["body","bore","pins"]},"bcm-gi-barrel-nut":{"part":"bcm-gi-barrel-nut","model":"bcm-gi-barrel-nut.glb","script":"bcm_gi_barrel_nut.py","inputs":{"bcm-gi-barrel-nut.flange_diameter":1.56,"bcm-gi-barrel-nut.length":0.85,"bcm-gi-barrel-nut.notches":20,"bcm-m4-upper.thread_pitch":0.0556,"std.ar15.barrel_nut_body_od":1.367,"std.ar15.barrel_nut_bore_d":1.01,"std.ar15.barrel_nut_counterbore_d":1.25,"std.ar15.barrel_nut_flange_chamfer":0.03,"std.ar15.barrel_nut_flange_od":1.56,"std.ar15.barrel_nut_flange_rear":0.73,"std.ar15.barrel_nut_front_recess":0.2,"std.ar15.barrel_nut_groove":0.126,"std.ar15.barrel_nut_groove_d":1.333,"std.ar15.barrel_nut_groove_width":0.045,"std.ar15.barrel_nut_inner_chamfer":0.03,"std.ar15.barrel_nut_length":0.85,"std.ar15.barrel_nut_notch_d":0.186,"std.ar15.barrel_nut_notch_pcd":1.561,"std.ar15.barrel_nut_notches":20,"std.ar15.barrel_nut_rear_chamfer":0.015,"std.ar15.barrel_nut_rear_x":-0.394,"std.ar15.barrel_nut_recess_round":0.06,"std.ar15.barrel_nut_shoulder":0.525,"std.ar15.barrel_nut_thread_chamfer":0.04,"std.ar15.barrel_nut_thread_length":0.394,"std.ar15.barrel_nut_thread_major_d":1.244,"std.ar15.barrel_nut_thread_minor_d":1.19},"profiles":{},"bounds":{"min":[-0.394,-0.7743,-0.7743],"max":[0.456,0.7743,0.7743]},"volume_in3":0.3023,"centroid":[0.0711,-0.0008,0],"shell":[0.0474,0.0006,-0.0001],"area_in2":9.2759,"triangles":24104,"manifold":true,"slabs":[[-0.394,-0.774,-0.573,0.456,-0.387,0.573],[-0.394,-0.387,-0.774,0.456,0.387,0.774],[-0.394,0.387,-0.573,0.456,0.774,0.573]],"slots":["nut"]},"bcm-grip-mod-3":{"part":"bcm-grip-mod-3","model":"bcm-grip-mod-3.glb","script":"bcm_grip_mod_3.py","inputs":{"bcm-grip-mod-3.bottom_below_lower_underside":4.242,"bcm-grip-mod-3.foot_width":1.36,"bcm-grip-mod-3.grip_angle":19.59,"bcm-grip-mod-3.lug_slot_width":0.385,"bcm-grip-mod-3.rib_reach":0.138,"bcm-grip-mod-3.seat_x":-0.094,"bcm-grip-mod-3.thickness":1.236,"bcm-grip-mod-3.top_block_width":0.88,"std.ar15.deck_y":0.2485,"std.ar15.grip_lug_depth":0.93,"std.ar15.grip_lug_face_angle":60,"std.ar15.grip_lug_face_from_pin":1.228,"std.ar15.grip_lug_front_from_rear_face":2.3,"std.ar15.grip_lug_length":1.25,"std.ar15.grip_lug_width":0.375,"std.ar15.grip_seat_below_deck":1.318,"std.ar15.rear_underside_arc_center_below_seat":0.1928,"std.ar15.rear_underside_arc_center_x":-1.0238,"std.ar15.rear_underside_arc_r_fullest":0.716,"std.ar15.rear_underside_round_r":0.44,"std.ar15.receiver_rear_x":-1.125},"profiles":{"side":[[-1.574,-3.478],[-1.561,-3.553],[-1.564,-3.613],[-1.541,-3.702],[-1.523,-3.718],[-1.528,-3.724],[-1.516,-3.721],[-1.471,-3.753],[-1.461,-3.749],[-1.437,-3.767],[-1.405,-3.771],[-1.406,-3.784],[-1.38,-3.803],[-1.039,-3.903],[-1.005,-3.91],[-0.977,-3.904],[-0.981,-3.922],[-0.963,-3.942],[-0.337,-4.104],[-0.314,-4.084],[-0.292,-4.098],[-0.307,-4.098],[-0.302,-4.107],[-0.14,-4.149],[-0.119,-4.164],[0.144,-4.238],[0.154,-4.238],[0.151,-4.231],[0.09,-4.217],[0.086,-4.21],[0.095,-4.205],[0.215,-4.242],[0.273,-4.231],[0.333,-4.18],[0.366,-4.175],[0.367,-4.146],[0.397,-4.101],[0.407,-4.041],[0.396,-3.991],[0.306,-3.864],[0.293,-3.82],[0.293,-3.771],[0.306,-3.726],[0.322,-3.716],[0.322,-3.674],[0.339,-3.663],[0.338,-3.625],[0.356,-3.608],[0.355,-3.569],[0.372,-3.558],[0.372,-3.516],[0.389,-3.505],[0.388,-3.467],[0.405,-3.453],[0.405,-3.411],[0.423,-3.398],[0.422,-3.36],[0.439,-3.347],[0.439,-3.306],[0.455,-3.295],[0.456,-3.253],[0.472,-3.242],[0.468,-3.214],[0.49,-3.184],[0.488,-3.15],[0.506,-3.133],[0.505,-3.097],[0.523,-3.079],[0.522,-3.043],[0.539,-3.03],[0.538,-2.992],[0.556,-2.977],[0.555,-2.941],[0.572,-2.925],[0.567,-2.902],[0.585,-2.88],[0.587,-2.838],[0.605,-2.823],[0.603,-2.787],[0.622,-2.769],[0.62,-2.735],[0.637,-2.72],[0.637,-2.682],[0.654,-2.669],[0.655,-2.631],[0.673,-2.616],[0.669,-2.588],[0.69,-2.562],[0.688,-2.526],[0.706,-2.511],[0.705,-2.473],[0.72,-2.466],[0.721,-2.423],[0.738,-2.408],[0.737,-2.372],[0.758,-2.344],[0.754,-2.321],[0.773,-2.306],[0.77,-2.269],[0.791,-2.251],[0.786,-2.218],[0.803,-2.207],[0.802,-2.167],[0.819,-2.154],[0.819,-2.115],[0.835,-2.104],[0.84,-2.086],[0.836,-2.062],[0.851,-2.053],[0.851,-2.013],[0.873,-1.983],[0.868,-1.959],[0.885,-1.948],[0.884,-1.91],[0.9,-1.899],[0.901,-1.856],[0.917,-1.847],[0.92,-1.804],[0.936,-1.793],[0.932,-1.76],[0.953,-1.739],[0.949,-1.707],[0.967,-1.689],[0.965,-1.655],[0.985,-1.591],[1.031,-1.521],[1.074,-1.486],[1.127,-1.46],[1.474,-1.39],[1.567,-1.379],[1.598,-1.349],[1.617,-1.289],[1.606,-1.267],[1.581,-1.26],[1.28,-1.258],[1.265,-1.244],[1.262,-0.962],[1.28,-0.947],[1.283,-0.927],[1.265,-0.902],[1.266,-0.224],[1.248,-0.152],[1.223,-0.108],[1.176,-0.057],[1.105,-0.015],[1.001,0.004],[0.611,-0.003],[-0.001,0.006],[-0.036,0.126],[-0.095,0.261],[-0.165,0.371],[-0.249,0.47],[-0.364,0.57],[-0.475,0.639],[-0.629,0.703],[-0.704,0.715],[-0.76,0.696],[-0.805,0.652],[-0.842,0.56],[-0.876,0.428],[-0.848,0.388],[-0.765,0.339],[-0.714,0.296],[-0.641,0.213],[-0.57,0.094],[-0.544,0.025],[-0.508,-0.146],[-0.482,-0.459],[-0.486,-0.684],[-0.508,-0.838],[-0.561,-1.031],[-0.608,-1.153],[-0.953,-1.793],[-1.075,-2.043],[-1.158,-2.248],[-1.468,-3.067],[-1.536,-3.283]],"rear":[[-0.68,-4.759],[-0.672,-4.8],[-0.639,-4.857],[-0.593,-4.886],[0.569,-4.886],[0.639,-4.825],[0.647,-4.775],[0.68,-4.717],[0.68,-4.478],[0.655,-4.149],[0.663,-3.893],[0.647,-3.341],[0.655,-3.102],[0.647,-3.094],[0.647,-2.361],[0.639,-2.353],[0.647,-2.344],[0.639,-1.916],[0.647,-1.908],[0.647,-1.619],[0.639,-1.545],[0.606,-1.438],[0.474,-1.174],[0.449,-1.084],[0.441,-0.754],[0.449,-0.556],[0.433,-0.54],[0.441,-0.507],[0.416,-0.457],[0.408,-0.251],[0.383,-0.078],[0.358,-0.012],[0.338,0],[0.264,-0.082],[0.157,-0.157],[0.049,-0.198],[-0.058,-0.214],[-0.173,-0.206],[-0.264,-0.181],[-0.371,-0.124],[-0.478,-0.016],[-0.49,-0.021],[-0.466,-0.111],[-0.433,-1.149],[-0.466,-1.314],[-0.49,-1.339],[-0.49,-1.364],[-0.556,-1.487],[-0.589,-1.677],[-0.589,-2.122],[-0.606,-2.402],[-0.597,-2.46],[-0.639,-3.687],[-0.63,-3.844],[-0.647,-3.902],[-0.639,-4.083],[-0.663,-4.47],[-0.663,-4.594],[-0.647,-4.66],[-0.672,-4.684]]},"features":{"side":{},"rear":{}},"placement":{"side":{"plane":"xy","offset":{}},"rear":{"plane":"zy","offset":{}}},"bounds":{"min":[-1.574,-4.2418,-0.6712],"max":[1.6153,0.6979,0.6712]},"volume_in3":7.1622,"centroid":[-0.1237,-2.1736,0],"shell":[-0.0083,-1.852,0],"area_in2":28.5062,"triangles":33008,"manifold":true,"receiver":{"slot":{"width":0.385,"clear_of_lug":0.005,"rear_x":0.014,"floor_at_rear_y":-0.3081,"foot_x":1.0999,"bottom_y":-0.935},"scoop":{"axis_x":-0.9298,"axis_y":-0.1928,"on_centre_plane_r":0.711,"across_r":0.445}},"slabs":[[-1.179,-4.242,-0.671,0.407,-3.862,0.671],[-1.573,-3.862,-0.671,0.389,-3.482,0.671],[-1.574,-3.482,-0.657,0.506,-3.102,0.657],[-1.479,-3.102,-0.649,0.635,-2.722,0.649],[-1.337,-2.722,-0.639,0.758,-2.342,0.639],[-1.194,-2.342,-0.631,0.873,-1.962,0.631],[-1.035,-1.962,-0.624,0.991,-1.582,0.624],[-0.839,-1.582,-0.618,1.615,-1.202,0.618],[-0.634,-1.202,-0.612,1.282,-0.822,0.612],[-0.526,-0.822,-0.478,1.266,-0.062,0.478],[-0.74,-0.062,-0.444,1.181,0.318,0.444],[-0.876,0.318,-0.444,-0.232,0.698,0.444]],"slots":["body"]},"bcm-grip-mod-4":{"part":"bcm-grip-mod-4","model":"bcm-grip-mod-4.glb","script":"bcm_grip_mod_4.py","inputs":{"bcm-grip-mod-4.base_wall":0.12,"bcm-grip-mod-4.block_front_x":1.265,"bcm-grip-mod-4.bottom_below_lower_underside":4.179,"bcm-grip-mod-4.foot_width":1.279,"bcm-grip-mod-4.grip_angle":17.4,"bcm-grip-mod-4.hollow_top_below_top":1.3,"bcm-grip-mod-4.lug_slot_width":0.394,"bcm-grip-mod-4.rib_reach":0.2,"bcm-grip-mod-4.seat_x":-0.09,"bcm-grip-mod-4.thickness":1.239,"bcm-grip-mod-4.top_block_width":0.88,"std.ar15.deck_y":0.2485,"std.ar15.grip_lug_depth":0.93,"std.ar15.grip_lug_face_angle":60,"std.ar15.grip_lug_face_from_pin":1.228,"std.ar15.grip_lug_front_from_rear_face":2.3,"std.ar15.grip_lug_length":1.25,"std.ar15.grip_lug_width":0.375,"std.ar15.grip_seat_below_deck":1.318,"std.ar15.rear_underside_arc_center_below_seat":0.1928,"std.ar15.rear_underside_arc_center_x":-1.0238,"std.ar15.rear_underside_arc_r_fullest":0.716,"std.ar15.rear_underside_round_r":0.44,"std.ar15.receiver_rear_x":-1.125},"profiles":{"side":[[-1.381,-3.462],[-1.37,-3.588],[-1.348,-3.69],[-1.331,-3.728],[-1.268,-3.784],[-1.106,-3.862],[-0.852,-3.943],[-0.622,-3.991],[-0.244,-4.088],[0.125,-4.166],[0.303,-4.179],[0.371,-4.171],[0.42,-4.149],[0.49,-4.062],[0.521,-4.003],[0.529,-3.956],[0.522,-3.899],[0.492,-3.84],[0.418,-3.756],[0.414,-3.691],[0.42,-3.667],[0.468,-3.626],[0.471,-3.553],[0.503,-3.497],[0.496,-3.452],[0.528,-3.411],[0.525,-3.35],[0.557,-3.31],[0.553,-3.248],[0.589,-3.197],[0.582,-3.143],[0.611,-3.115],[0.617,-3.095],[0.606,-3.042],[0.639,-3.013],[0.646,-2.993],[0.648,-2.966],[0.635,-2.94],[0.661,-2.923],[0.675,-2.896],[0.672,-2.854],[0.66,-2.839],[0.695,-2.82],[0.703,-2.794],[0.706,-2.771],[0.688,-2.738],[0.716,-2.722],[0.732,-2.697],[0.733,-2.654],[0.717,-2.636],[0.754,-2.611],[0.763,-2.58],[0.762,-2.56],[0.745,-2.535],[0.784,-2.507],[0.792,-2.482],[0.791,-2.459],[0.774,-2.429],[0.809,-2.414],[0.821,-2.38],[0.819,-2.354],[0.802,-2.328],[0.834,-2.312],[0.85,-2.283],[0.848,-2.248],[0.831,-2.226],[0.863,-2.211],[0.875,-2.193],[0.877,-2.151],[0.86,-2.128],[0.891,-2.109],[0.907,-2.08],[0.905,-2.053],[0.888,-2.027],[0.901,-2.009],[0.927,-2.004],[0.936,-1.982],[0.934,-1.955],[0.917,-1.925],[0.929,-1.907],[0.956,-1.902],[0.965,-1.884],[0.966,-1.85],[0.946,-1.832],[0.949,-1.816],[0.99,-1.791],[0.995,-1.748],[0.974,-1.726],[0.978,-1.715],[1.009,-1.699],[1.025,-1.67],[1.024,-1.647],[1.003,-1.621],[1.029,-1.543],[1.067,-1.479],[1.099,-1.452],[1.538,-1.346],[1.601,-1.319],[1.621,-1.289],[1.614,-1.243],[1.585,-1.232],[1.297,-1.241],[1.268,-1.229],[1.26,-0.239],[1.226,-0.133],[1.197,-0.085],[1.154,-0.04],[1.078,0.002],[1.016,0.014],[0.974,0.011],[0.967,0.003],[0.913,0],[0.882,0.01],[0.875,0.002],[0.81,-0.002],[0.725,0.008],[0.211,0.001],[0.131,-0.008],[0.122,0],[0.042,-0.005],[0.001,0.002],[-0.023,0.085],[-0.08,0.216],[-0.131,0.301],[-0.227,0.419],[-0.342,0.518],[-0.461,0.591],[-0.544,0.632],[-0.669,0.667],[-0.715,0.665],[-0.779,0.645],[-0.822,0.61],[-0.851,0.532],[-0.851,0.39],[-0.757,0.332],[-0.642,0.233],[-0.58,0.152],[-0.502,0.003],[-0.466,-0.148],[-0.424,-0.411],[-0.415,-0.618],[-0.437,-0.842],[-0.493,-1.064],[-0.573,-1.264],[-0.709,-1.506],[-0.856,-1.807],[-1.041,-2.248],[-1.237,-2.839],[-1.324,-3.132],[-1.37,-3.331]],"rear":[[-0.653,-4.46],[-0.598,-4.542],[-0.526,-4.586],[-0.447,-4.615],[-0.231,-4.658],[-0.007,-4.672],[0.26,-4.658],[0.433,-4.622],[0.57,-4.564],[0.602,-4.539],[0.638,-4.481],[0.638,-3.976],[0.624,-3.962],[0.631,-3.71],[0.616,-3.666],[0.616,-3.032],[0.624,-2.989],[0.645,-2.967],[0.631,-2.844],[0.645,-2.455],[0.638,-2.304],[0.653,-2.217],[0.631,-2.188],[0.631,-2.087],[0.616,-2.059],[0.631,-2.022],[0.631,-1.395],[0.616,-1.237],[0.609,-1.208],[0.573,-1.164],[0.58,-1.136],[0.544,-1.078],[0.53,-1.013],[0.512,-1.017],[0.487,-0.984],[0.516,-0.963],[0.505,-0.945],[0.49,-0.959],[0.472,-0.941],[0.465,-0.746],[0.487,-0.097],[0.479,-0.032],[0.454,-0.007],[0.429,-0.068],[0.375,-0.13],[0.357,-0.112],[0.361,-0.101],[0.26,-0.101],[0.238,-0.115],[0.205,-0.155],[0.205,-0.198],[0.22,-0.227],[0.187,-0.252],[0.108,-0.274],[-0.022,-0.274],[-0.166,-0.231],[-0.184,-0.213],[-0.169,-0.198],[-0.169,-0.155],[-0.209,-0.108],[-0.292,-0.105],[-0.242,-0.155],[-0.26,-0.173],[-0.328,-0.105],[-0.389,0],[-0.415,-0.047],[-0.422,-1.02],[-0.454,-1.053],[-0.479,-1.027],[-0.465,-0.977],[-0.472,-0.948],[-0.501,-1.049],[-0.544,-1.136],[-0.544,-1.179],[-0.566,-1.208],[-0.58,-1.294],[-0.595,-1.316],[-0.588,-1.453],[-0.602,-1.525],[-0.602,-1.676],[-0.588,-1.698],[-0.602,-1.813],[-0.588,-1.828],[-0.602,-1.842],[-0.602,-1.943],[-0.588,-1.958],[-0.588,-1.986],[-0.602,-2.001],[-0.595,-2.087],[-0.609,-2.116],[-0.595,-2.174],[-0.624,-2.21],[-0.624,-2.83],[-0.609,-2.852],[-0.624,-2.873],[-0.624,-2.974],[-0.609,-2.989],[-0.609,-3.335],[-0.624,-3.472],[-0.616,-3.565],[-0.638,-3.984],[-0.631,-4.099],[-0.645,-4.135],[-0.638,-4.279]]},"features":{"side":{},"rear":{}},"placement":{"side":{"plane":"xy","offset":{}},"rear":{"plane":"zy","offset":{}}},"bounds":{"min":[-1.381,-4.179,-0.6418],"max":[1.6207,0.6524,0.6418]},"volume_in3":3.7667,"centroid":[0.1654,-1.5745,0],"shell":[0.0075,-2.0106,0],"area_in2":37.5382,"triangles":37962,"manifold":true,"receiver":{"slot":{"width":0.394,"clear_of_lug":0.0095,"rear_x":0.0055,"floor_at_rear_y":-0.3107,"foot_x":1.0947,"bottom_y":-0.9395},"scoop":{"axis_x":-0.9338,"axis_y":-0.1928,"on_centre_plane_r":0.7065,"across_r":0.4495}},"slabs":[[-1.22,-4.179,-0.641,0.529,-3.807,0.641],[-1.381,-3.807,-0.642,0.509,-3.436,0.642],[-1.379,-3.436,-0.636,0.617,-3.064,0.636],[-1.304,-3.064,-0.619,0.732,-2.692,0.619],[-1.188,-2.692,-0.629,0.821,-2.321,0.629],[-1.065,-2.321,-0.634,0.936,-1.949,0.634],[-0.916,-1.949,-0.634,1.025,-1.577,0.634],[-0.744,-1.577,-0.616,1.621,-1.206,0.616],[-0.55,-1.206,-0.616,1.268,-0.834,0.616],[-0.436,-0.834,-0.575,1.265,-0.463,0.575],[-0.48,-0.463,-0.444,1.262,-0.091,0.444],[-0.697,-0.091,-0.444,1.201,0.281,0.444],[-0.851,0.281,-0.444,-0.223,0.652,0.444]],"slots":["body"]},"bcm-h-buffer":{"part":"bcm-h-buffer","model":"bcm-h-buffer.glb","script":"bcm_carbine_buffer.py","inputs":{"bcm-h-buffer.length":3.251,"bcm-h-buffer.od":0.98,"std.carbine_buffer.body_d":0.687,"std.carbine_buffer.body_length":2.854,"std.carbine_buffer.body_start":0.5145,"std.carbine_buffer.bumper_band":0.06,"std.carbine_buffer.bumper_d":0.687,"std.carbine_buffer.bumper_exposed":0.4,"std.carbine_buffer.bumper_taper":13.5,"std.carbine_buffer.head_d":0.98,"std.carbine_buffer.head_flat_across":0.952,"std.carbine_buffer.head_rim":0.214,"std.carbine_buffer.head_thickness":0.254,"std.carbine_buffer.length":3.251,"std.carbine_buffer.pilot_d":0.781,"std.carbine_buffer.pilot_end":0.468,"std.carbine_buffer.pin_d":0.122,"std.carbine_buffer.pin_from_open_end":0.24},"profiles":{},"bounds":{"min":[0,-0.49,-0.49],"max":[3.251,0.462,0.49]},"volume_in3":1.2939,"centroid":[1.4641,0,0],"shell":[1.5949,0,0],"area_in2":9.6585,"triangles":7276,"manifold":true,"slabs":[[0,-0.49,-0.49,0.361,0.462,0.49],[0.361,-0.391,-0.391,3.251,0.391,0.391]],"slots":["body","bumper","pin"]},"bcm-h2-buffer":{"part":"bcm-h2-buffer","model":"bcm-h2-buffer.glb","script":"bcm_carbine_buffer.py","inputs":{"bcm-h2-buffer.length":3.251,"bcm-h2-buffer.od":0.98,"std.carbine_buffer.body_d":0.687,"std.carbine_buffer.body_length":2.854,"std.carbine_buffer.body_start":0.5145,"std.carbine_buffer.bumper_band":0.06,"std.carbine_buffer.bumper_d":0.687,"std.carbine_buffer.bumper_exposed":0.4,"std.carbine_buffer.bumper_taper":13.5,"std.carbine_buffer.head_d":0.98,"std.carbine_buffer.head_flat_across":0.952,"std.carbine_buffer.head_rim":0.214,"std.carbine_buffer.head_thickness":0.254,"std.carbine_buffer.length":3.251,"std.carbine_buffer.pilot_d":0.781,"std.carbine_buffer.pilot_end":0.468,"std.carbine_buffer.pin_d":0.122,"std.carbine_buffer.pin_from_open_end":0.24},"profiles":{},"bounds":{"min":[0,-0.49,-0.49],"max":[3.251,0.462,0.49]},"volume_in3":1.2939,"centroid":[1.4641,0,0],"shell":[1.5949,0,0],"area_in2":9.6585,"triangles":7276,"manifold":true,"slabs":[[0,-0.49,-0.49,0.361,0.462,0.49],[0.361,-0.391,-0.391,3.251,0.391,0.391]],"slots":["body","bumper","pin"]},"bcm-h3-buffer":{"part":"bcm-h3-buffer","model":"bcm-h3-buffer.glb","script":"bcm_carbine_buffer.py","inputs":{"bcm-h3-buffer.length":3.251,"bcm-h3-buffer.od":0.98,"std.carbine_buffer.body_d":0.687,"std.carbine_buffer.body_length":2.854,"std.carbine_buffer.body_start":0.5145,"std.carbine_buffer.bumper_band":0.06,"std.carbine_buffer.bumper_d":0.687,"std.carbine_buffer.bumper_exposed":0.4,"std.carbine_buffer.bumper_taper":13.5,"std.carbine_buffer.head_d":0.98,"std.carbine_buffer.head_flat_across":0.952,"std.carbine_buffer.head_rim":0.214,"std.carbine_buffer.head_thickness":0.254,"std.carbine_buffer.length":3.251,"std.carbine_buffer.pilot_d":0.781,"std.carbine_buffer.pilot_end":0.468,"std.carbine_buffer.pin_d":0.122,"std.carbine_buffer.pin_from_open_end":0.24},"profiles":{},"bounds":{"min":[0,-0.49,-0.49],"max":[3.251,0.462,0.49]},"volume_in3":1.2939,"centroid":[1.4641,0,0],"shell":[1.5949,0,0],"area_in2":9.6585,"triangles":7276,"manifold":true,"slabs":[[0,-0.49,-0.49,0.361,0.462,0.49],[0.361,-0.391,-0.391,3.251,0.391,0.391]],"slots":["body","bumper","pin"]},"bcm-handguard-cap-round-750":{"part":"bcm-handguard-cap-round-750","model":"bcm-handguard-cap-round-750.glb","script":"bcm_handguard_cap_round_750.py","inputs":{"bcm-handguard-cap-round-750.bend_r":0.11811023622047244,"bcm-handguard-cap-round-750.bore_d":0.7509999999999999,"bcm-handguard-cap-round-750.length":0.2755905511811024,"bcm-handguard-cap-round-750.lip_bend_len":0.028141732283464567,"bcm-handguard-cap-round-750.lip_len":0.04105511811023622,"bcm-handguard-cap-round-750.lip_od":1.6929133858267715,"bcm-handguard-cap-round-750.sheet":0.032,"bcm-handguard-cap-round-750.skirt_od":1.6811023622047245,"bcm-handguard-cap-round-750.slot_hi":0.7529527559055118,"bcm-handguard-cap-round-750.slot_lo":0.5285433070866142,"bcm-handguard-cap-round-750.slot_w":0.18503937007874016,"bcm-handguard-cap-round-750.tab_bend_r":0.07874015748031496,"bcm-handguard-cap-round-750.tab_bend_x":0.049212598425196846,"bcm-handguard-cap-round-750.tab_set_r":0.7224409448818898,"bcm-handguard-cap-round-750.tab_step_x":0.1279527559055118,"bcm-handguard-cap-round-750.tab_w":0.17716535433070865},"profiles":{},"bounds":{"min":[-0.2756,-0.8465,-0.8465],"max":[0,0.8465,0.8465]},"volume_in3":0.08863,"centroid":[-0.0812,-0.0079,0],"shell":[-0.0855,-0.0051,0],"area_in2":5.8623,"triangles":9728,"manifold":true,"slabs":[[-0.276,-0.846,-0.677,0,-0.508,0.677],[-0.276,-0.508,-0.846,0,0.508,0.846],[-0.276,0.508,-0.677,0,0.846,0.677]],"slots":["cap"]},"bcm-handguard-cap-triangle-750":{"part":"bcm-handguard-cap-triangle-750","model":"bcm-handguard-cap-triangle-750.glb","script":"bcm_handguard_cap_triangle_750.py","inputs":{"bcm-handguard-cap-triangle-750.apex_r":0.912,"bcm-handguard-cap-triangle-750.bend_r":0.09,"bcm-handguard-cap-triangle-750.bore_d":0.7525,"bcm-handguard-cap-triangle-750.collar":0.058,"bcm-handguard-cap-triangle-750.corner_circle_r":0.625,"bcm-handguard-cap-triangle-750.corner_r":0.287,"bcm-handguard-cap-triangle-750.height":1.626,"bcm-handguard-cap-triangle-750.length":0.328,"bcm-handguard-cap-triangle-750.sheet":0.025,"bcm-handguard-cap-triangle-750.side_centre_r":0.912,"bcm-handguard-cap-triangle-750.side_r":1.626,"bcm-handguard-cap-triangle-750.skirt_depth":0.24,"bcm-handguard-cap-triangle-750.slot_hi":0.737,"bcm-handguard-cap-triangle-750.slot_lo":0.513,"bcm-handguard-cap-triangle-750.slot_w":0.187,"bcm-handguard-cap-triangle-750.width":1.656},"profiles":{},"bounds":{"min":[-0.323,-0.714,-0.8282],"max":[0,0.912,0.8282]},"volume_in3":0.06698,"centroid":[-0.1292,-0.008,0],"shell":[-0.132,-0.0058,0],"area_in2":5.5687,"triangles":6672,"manifold":true,"slabs":[[-0.323,-0.636,-0.828,-0.058,0.538,-0.497],[-0.323,-0.705,-0.497,0,0.859,-0.166],[-0.323,-0.714,-0.166,0,0.912,0.166],[-0.323,-0.705,0.166,0,0.859,0.497],[-0.323,-0.636,0.497,-0.058,0.538,0.828]],"slots":["cap"]},"bcm-kag-mlok":{"part":"bcm-kag-mlok","model":"bcm-kag-mlok.glb","script":"bcm_kag_mlok.py","inputs":{"bcm-kag-mlok.cup_depth":0.05,"bcm-kag-mlok.cup_front":0.96,"bcm-kag-mlok.cup_rim":0.1,"bcm-kag-mlok.cup_top":0.4,"bcm-kag-mlok.edge_round":0.03,"bcm-kag-mlok.face_hollow_depth":0.06,"bcm-kag-mlok.face_rim":0.1,"bcm-kag-mlok.front_head_proud":0.02,"bcm-kag-mlok.length":2.73,"bcm-kag-mlok.lug_x":0.767,"bcm-kag-mlok.nut_spacing":0.777,"bcm-kag-mlok.plan_corner":0.08,"bcm-kag-mlok.rib_depth":0.025,"bcm-kag-mlok.rib_gap":0.022,"bcm-kag-mlok.rib_pitch":0.061,"bcm-kag-mlok.ribs_back_count":16,"bcm-kag-mlok.ribs_back_from_y":0.159,"bcm-kag-mlok.ribs_back_to_y":1.058,"bcm-kag-mlok.ribs_front_from_x":2.69,"bcm-kag-mlok.ribs_front_to_y":1.315,"bcm-kag-mlok.screw_head":0.25,"bcm-kag-mlok.tail_counterbore":0.34,"bcm-kag-mlok.toe_bore":0.42,"bcm-kag-mlok.toe_bore_depth":0.75,"bcm-kag-mlok.width":0.65},"profiles":{"side":[[0,0.115],[0.006,0.109],[0.003,0.096],[0.012,0.087],[0.003,0.081],[0.009,0.047],[0,0.032],[0,0.017],[0.014,0.003],[0.038,0],[2.701,0],[2.721,0.008],[2.724,0.023],[2.718,0.029],[2.73,0.041],[2.73,0.063],[2.715,0.075],[2.709,0.093],[2.718,0.102],[2.706,0.118],[2.706,0.13],[2.693,0.139],[2.699,0.145],[2.658,0.183],[2.637,0.196],[2.621,0.196],[2.626,0.185],[2.621,0.18],[2.612,0.196],[2.606,0.193],[2.591,0.208],[2.57,0.214],[2.557,0.211],[2.548,0.226],[2.499,0.26],[2.414,0.284],[2.407,0.281],[2.395,0.29],[2.34,0.3],[2.313,0.312],[2.279,0.312],[2.23,0.333],[2.209,0.333],[2.148,0.355],[2.129,0.355],[2.114,0.364],[2.086,0.364],[2.028,0.385],[1.995,0.388],[1.946,0.407],[1.94,0.404],[1.863,0.422],[1.756,0.459],[1.732,0.459],[1.714,0.48],[1.701,0.477],[1.677,0.507],[1.631,0.535],[1.619,0.535],[1.603,0.553],[1.573,0.556],[1.53,0.596],[1.472,0.627],[1.466,0.624],[1.426,0.639],[1.377,0.639],[1.368,0.645],[1.356,0.636],[1.35,0.642],[1.328,0.636],[1.295,0.642],[1.282,0.651],[1.273,0.648],[1.264,0.657],[1.246,0.66],[1.209,0.688],[1.197,0.694],[1.191,0.691],[1.16,0.721],[1.136,0.728],[1.131,0.732],[1.134,0.741],[1.117,0.764],[1.111,0.767],[1.099,0.761],[1.091,0.769],[1.101,0.781],[1.094,0.809],[1.075,0.813],[1.067,0.824],[1.082,0.839],[1.076,0.851],[1.079,0.864],[1.058,0.873],[1.058,0.885],[1.076,0.894],[1.076,0.922],[1.061,0.931],[1.061,0.94],[1.068,0.948],[1.085,0.949],[1.088,0.977],[1.076,0.992],[1.084,1.003],[1.096,1.003],[1.104,1.016],[1.107,1.032],[1.091,1.041],[1.091,1.056],[1.116,1.062],[1.113,1.078],[1.119,1.09],[1.101,1.105],[1.111,1.119],[1.134,1.12],[1.128,1.136],[1.14,1.145],[1.128,1.151],[1.119,1.166],[1.143,1.175],[1.146,1.194],[1.156,1.203],[1.134,1.221],[1.145,1.235],[1.163,1.232],[1.162,1.246],[1.174,1.258],[1.159,1.27],[1.153,1.289],[1.163,1.293],[1.169,1.287],[1.186,1.289],[1.18,1.295],[1.195,1.313],[1.183,1.325],[1.189,1.344],[1.186,1.353],[1.206,1.363],[1.212,1.36],[1.214,1.377],[1.229,1.389],[1.235,1.399],[1.232,1.405],[1.244,1.411],[1.241,1.42],[1.256,1.438],[1.263,1.478],[1.275,1.481],[1.281,1.5],[1.281,1.527],[1.275,1.539],[1.281,1.551],[1.275,1.579],[1.266,1.591],[1.269,1.597],[1.253,1.616],[1.256,1.622],[1.234,1.651],[1.226,1.652],[1.221,1.666],[1.209,1.669],[1.185,1.694],[1.133,1.715],[1.056,1.721],[0.965,1.694],[0.943,1.697],[0.922,1.688],[0.909,1.694],[0.879,1.678],[0.861,1.681],[0.848,1.675],[0.842,1.681],[0.809,1.663],[0.784,1.663],[0.775,1.654],[0.766,1.657],[0.711,1.636],[0.702,1.639],[0.695,1.632],[0.662,1.626],[0.656,1.617],[0.549,1.602],[0.512,1.587],[0.506,1.59],[0.488,1.581],[0.405,1.562],[0.347,1.535],[0.312,1.503],[0.29,1.472],[0.275,1.441],[0.275,1.432],[0.287,1.423],[0.283,1.418],[0.274,1.428],[0.266,1.42],[0.275,1.414],[0.263,1.408],[0.272,1.393],[0.26,1.389],[0.263,1.383],[0.254,1.368],[0.263,1.362],[0.251,1.359],[0.254,1.347],[0.248,1.341],[0.254,1.334],[0.238,1.313],[0.251,1.298],[0.242,1.292],[0.242,1.252],[0.235,1.246],[0.235,1.234],[0.245,1.224],[0.235,1.221],[0.245,1.206],[0.238,1.185],[0.251,1.16],[0.245,1.148],[0.257,1.117],[0.251,1.099],[0.263,1.096],[0.26,1.087],[0.269,1.072],[0.243,1.064],[0.235,1.056],[0.235,1.044],[0.255,1.018],[0.264,1.033],[0.281,1.029],[0.269,1.023],[0.267,1.012],[0.255,1.015],[0.238,1.004],[0.238,0.977],[0.269,0.968],[0.232,0.943],[0.238,0.916],[0.257,0.903],[0.252,0.887],[0.246,0.89],[0.232,0.882],[0.242,0.864],[0.238,0.854],[0.258,0.847],[0.274,0.868],[0.281,0.848],[0.281,0.836],[0.272,0.827],[0.281,0.818],[0.281,0.802],[0.275,0.796],[0.281,0.79],[0.278,0.772],[0.264,0.761],[0.255,0.77],[0.232,0.766],[0.238,0.76],[0.235,0.735],[0.255,0.718],[0.264,0.731],[0.274,0.734],[0.278,0.729],[0.271,0.7],[0.255,0.715],[0.232,0.705],[0.232,0.674],[0.254,0.656],[0.229,0.644],[0.235,0.631],[0.232,0.619],[0.257,0.592],[0.229,0.585],[0.229,0.561],[0.26,0.533],[0.252,0.526],[0.24,0.532],[0.229,0.527],[0.235,0.5],[0.229,0.494],[0.251,0.475],[0.243,0.468],[0.231,0.471],[0.226,0.466],[0.232,0.46],[0.229,0.433],[0.257,0.414],[0.248,0.411],[0.246,0.4],[0.237,0.416],[0.223,0.411],[0.22,0.399],[0.226,0.387],[0.22,0.374],[0.245,0.356],[0.243,0.345],[0.249,0.352],[0.254,0.344],[0.234,0.339],[0.225,0.361],[0.211,0.356],[0.214,0.335],[0.205,0.313],[0.191,0.309],[0.183,0.298],[0.183,0.274],[0.173,0.263],[0.157,0.263],[0.15,0.255],[0.153,0.231],[0.139,0.214],[0.127,0.226],[0.104,0.216],[0.107,0.191],[0.092,0.179],[0.084,0.156],[0.069,0.168],[0.061,0.167],[0.058,0.16],[0.073,0.148],[0.053,0.125],[0.044,0.138],[0.034,0.139],[0.035,0.156],[0.024,0.151],[0.028,0.142],[0.009,0.121],[0.015,0.115],[0.011,0.11]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{}}},"bounds":{"min":[0.0042,0,-0.325],"max":[2.7277,1.7192,0.325]},"volume_in3":1.1969,"centroid":[1.0378,0.5962,0],"shell":[1.0895,0.6486,0],"area_in2":13.2837,"triangles":6918,"manifold":true,"slabs":[[0.004,0,-0.325,0.393,1.556,0.325],[0.393,0,-0.325,0.782,1.659,0.325],[0.782,0,-0.325,1.561,1.719,0.325],[1.561,0,-0.325,1.95,0.585,0.325],[1.95,0,-0.325,2.339,0.412,0.325],[2.339,0,-0.325,2.728,0.312,0.325]],"slots":["body","screws"]},"bcm-m4-upper.receiver":{"part":"bcm-m4-upper","component":"receiver","model":"bcm-m4-upper.receiver.glb","script":"bcm_m4_upper.py","inputs":{"bcm-m4-upper.body_radius":0.595,"bcm-m4-upper.bore_axis_above_pin":0.8775,"bcm-m4-upper.bore_d":1.001,"bcm-m4-upper.cam_pad_edge_round":0.115,"bcm-m4-upper.cam_pad_face_z":0.5625,"bcm-m4-upper.cover_bead_corner_r":0.125,"bcm-m4-upper.cover_bead_gap":0.62,"bcm-m4-upper.cover_bead_height":0.05,"bcm-m4-upper.cover_bead_inset":0.12,"bcm-m4-upper.cover_bead_leg_spacing":1.115,"bcm-m4-upper.cover_bead_r":0.025,"bcm-m4-upper.cover_corner_r":0.25,"bcm-m4-upper.cover_height":0.79,"bcm-m4-upper.cover_hinge_curl_id":0.13,"bcm-m4-upper.cover_latch_width":0.45,"bcm-m4-upper.cover_length":3.13,"bcm-m4-upper.cover_seat_below_hinge":0.04,"bcm-m4-upper.cover_thickness":0.025,"bcm-m4-upper.deflector_bottom_y":0.95,"bcm-m4-upper.deflector_front_x":2.97,"bcm-m4-upper.deflector_out":1.26,"bcm-m4-upper.deflector_rear_x":2.06,"bcm-m4-upper.deflector_ridge_bottom_y":1.11,"bcm-m4-upper.deflector_ridge_top_y":1.67,"bcm-m4-upper.deflector_tip_x":2.4,"bcm-m4-upper.deflector_top_y":1.7,"bcm-m4-upper.dovetail_foot_half_width":0.323,"bcm-m4-upper.dovetail_foot_y":1.885,"bcm-m4-upper.fa_axis_angle":20,"bcm-m4-upper.fa_bore_d":0.509,"bcm-m4-upper.fa_bore_depth":0.65,"bcm-m4-upper.fa_cap_body_d":0.486,"bcm-m4-upper.fa_cap_body_length":0.57,"bcm-m4-upper.fa_cap_head_d":0.605,"bcm-m4-upper.fa_cap_length":0.71,"bcm-m4-upper.fa_cap_proud":0.5,"bcm-m4-upper.fa_housing_r":0.305,"bcm-m4-upper.fa_mouth_x":-0.44,"bcm-m4-upper.fa_mouth_z":1.0285,"bcm-m4-upper.front_face_x":7.036,"bcm-m4-upper.gas_tube_hole_above_bore":0.781,"bcm-m4-upper.gas_tube_hole_d":0.1835,"bcm-m4-upper.gas_tube_lobe_offset":0.11,"bcm-m4-upper.gas_tube_lobe_r":0.047,"bcm-m4-upper.handle_seat_x":0.068,"bcm-m4-upper.hinge_lug_front_x":6.235,"bcm-m4-upper.hinge_lug_r":0.1365,"bcm-m4-upper.hinge_lug_rear_x":2.806,"bcm-m4-upper.hinge_pin_front_x":6.6,"bcm-m4-upper.hinge_pin_rear_x":2.83,"bcm-m4-upper.hinge_y":0.641,"bcm-m4-upper.hinge_z":0.689,"bcm-m4-upper.index_notch_depth":0.16,"bcm-m4-upper.index_notch_width":0.127,"bcm-m4-upper.latch_slot_bottom_y":1.527,"bcm-m4-upper.latch_slot_floor":0.045,"bcm-m4-upper.latch_slot_length":0.195,"bcm-m4-upper.latch_slot_top_y":1.926,"bcm-m4-upper.latch_slot_wall":0.156,"bcm-m4-upper.left_pad_front_x":6.105,"bcm-m4-upper.left_pad_rear_foot_x":2.895,"bcm-m4-upper.left_pad_rear_x":2.975,"bcm-m4-upper.left_pad_top_y":0.601,"bcm-m4-upper.left_photo_lens_distance":35,"bcm-m4-upper.left_photo_lens_x":3.9,"bcm-m4-upper.left_photo_lens_y":3.3,"bcm-m4-upper.left_tab_face_top_y":0.316,"bcm-m4-upper.left_tab_front_x":4.57,"bcm-m4-upper.left_tab_rear_foot_x":3.898,"bcm-m4-upper.left_tab_rear_x":3.962,"bcm-m4-upper.left_tab_top_y":0.368,"bcm-m4-upper.lug_bottom_below_pin":0.216,"bcm-m4-upper.lug_hole_d":0.2505,"bcm-m4-upper.lug_wall_half_width":0.453,"bcm-m4-upper.lug_width":0.4945,"bcm-m4-upper.port_bottom_y":0.841,"bcm-m4-upper.port_end_r":0.25,"bcm-m4-upper.port_face_angle":22.5,"bcm-m4-upper.port_front_x":6.078,"bcm-m4-upper.port_length":3.125,"bcm-m4-upper.rail_front_x":6.593,"bcm-m4-upper.rail_neck_bottom_y":1.7,"bcm-m4-upper.rail_neck_half_width":0.309,"bcm-m4-upper.rail_tongue_rear_x":-0.62,"bcm-m4-upper.rail_top_above_pin":2.09,"bcm-m4-upper.receiver_rear_x":-0.621,"bcm-m4-upper.shoulder_x":6.591,"bcm-m4-upper.side_bottom_y":1.44,"bcm-m4-upper.side_half_width":0.319,"bcm-m4-upper.thread_major_d":1.244,"bcm-m4-upper.thread_minor_d":1.1803,"bcm-m4-upper.thread_pitch":0.0556,"bcm-m4-upper.underside_y":0.2485,"std.ar15.bore_axis_y":0.8775,"std.ar15.buffer_tower_front_x":-0.628,"std.ar15.buffer_tower_od":1.392,"std.ar15.buffer_trough_r":0.5625,"std.ar15.charging_handle_channel_floor_y":1.5845,"std.ar15.charging_handle_channel_front_round_x":5.726,"std.ar15.charging_handle_channel_rear_half_width":0.209,"std.ar15.charging_handle_channel_rear_round_x":0.676,"std.ar15.charging_handle_channel_roof_y":1.9085,"std.ar15.charging_handle_channel_round_r":0.2665,"std.ar15.charging_handle_channel_slot_half_width":0.205,"std.ar15.charging_handle_channel_tier_half_width":0.25,"std.ar15.charging_handle_channel_tier_top_y":1.7115,"std.ar15.charging_handle_channel_top_half_width":0.22,"std.ar15.charging_handle_notch_chamfer":0.083,"std.ar15.charging_handle_notch_floor_y":1.571,"std.ar15.charging_handle_notch_roof_y":1.89,"std.ar15.deck_y":0.2485,"std.ar15.pin_spacing":6.375,"std.ar15.rail_tongue_end_r":0.4175,"std.ar15.rail_tongue_fillet_r":0.1476,"std.ar15.rail_tongue_front_x":0.277,"std.ar15.rail_tongue_half_width":0.318,"std.ar15.rail_tongue_shoulder_x":0.4165,"std.ar15.rear_lug_slot_rear_x":-0.402,"std.ar15.rear_lug_slot_width":0.5,"std.ar15.rear_wall_arc_r":0.75,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.top_width":0.835},"profiles":{"side":[[-0.621,1.55],[-0.621,0.51],[-0.598,0.51],[-0.559,0.455],[-0.489,0.463],[-0.493,0.436],[-0.41,0.362],[-0.242,0.265],[-0.233,-0.213],[-0.213,-0.24],[-0.12,-0.247],[0.217,-0.247],[0.228,-0.235],[0.22,0.18],[0.247,0.191],[2.773,0.197],[2.836,0.181],[6.191,0.197],[6.204,-0.12],[6.294,-0.21],[6.349,-0.225],[6.458,-0.225],[6.552,-0.186],[6.61,-0.119],[6.626,-0.025],[6.625,0.201],[6.657,0.217],[6.66,0.292],[6.676,0.299],[6.707,0.268],[6.739,0.284],[6.754,0.26],[6.785,0.284],[6.817,0.261],[6.848,0.284],[6.872,0.261],[6.895,0.284],[6.918,0.269],[6.958,0.284],[6.989,0.269],[7.012,0.292],[7.036,0.293],[7.036,1.455],[6.994,1.497],[6.978,1.481],[6.939,1.497],[6.916,1.481],[6.892,1.497],[6.861,1.481],[6.83,1.496],[6.814,1.481],[6.775,1.496],[6.759,1.481],[6.72,1.496],[6.681,1.465],[6.654,1.469],[6.653,1.867],[6.668,1.914],[6.668,2.024],[6.66,2.055],[6.633,2.075],[6.218,2.074],[6.207,2.062],[6.211,2.003],[6.195,2.042],[6.156,2.035],[6.136,1.999],[6.148,1.98],[6.125,1.988],[6.109,1.948],[6.062,1.948],[6.011,1.952],[6.003,2.046],[5.984,2.073],[5.819,2.073],[5.808,2.061],[5.816,2.006],[5.8,2.006],[5.788,2.042],[5.765,2.042],[5.753,1.998],[5.777,1.975],[5.741,1.987],[5.695,1.979],[5.695,1.963],[5.73,1.951],[5.695,1.947],[5.612,1.951],[5.604,2.045],[5.585,2.072],[5.421,2.072],[5.409,2.06],[5.417,2.013],[5.366,2.002],[5.378,1.982],[5.366,1.97],[5.35,1.986],[5.327,1.947],[5.241,1.946],[5.214,1.958],[5.194,2.072],[5.014,2.071],[5.018,2.044],[4.99,2.048],[4.987,2.028],[5.014,2.032],[5.018,2.005],[4.979,1.997],[4.983,1.969],[4.959,1.985],[4.944,1.969],[4.893,1.973],[4.944,1.961],[4.936,1.946],[4.819,1.946],[4.795,2.071],[4.623,2.07],[4.611,2.059],[4.619,2.004],[4.588,1.996],[4.592,1.969],[4.568,1.976],[4.553,1.945],[4.428,1.945],[4.408,1.964],[4.396,2.07],[4.232,2.077],[4.212,2.065],[4.22,2.003],[4.189,1.995],[4.212,1.972],[4.209,1.952],[4.169,1.975],[4.162,1.944],[4.021,1.944],[3.997,2.069],[3.825,2.076],[3.813,2.002],[3.798,1.994],[3.81,1.951],[3.778,1.967],[3.755,1.943],[3.685,1.943],[3.61,1.955],[3.598,2.068],[3.426,2.075],[3.415,2.001],[3.399,1.985],[3.415,1.954],[3.387,1.966],[3.34,1.942],[3.215,1.95],[3.192,2.075],[3.027,2.075],[3.016,2],[3,1.992],[3.008,1.953],[2.934,1.941],[2.816,1.949],[2.805,1.961],[2.804,2.062],[2.785,2.074],[2.621,2.074],[2.597,1.948],[2.41,1.948],[2.386,2.073],[2.23,2.073],[2.21,2.061],[2.21,1.959],[2.198,1.948],[2.011,1.947],[1.999,1.959],[1.999,2.061],[1.987,2.072],[1.909,2.072],[1.811,2.068],[1.811,1.998],[1.792,1.947],[1.604,1.946],[1.6,2.06],[1.588,2.071],[1.455,2.071],[1.404,2.059],[1.401,1.993],[1.244,1.992],[1.205,1.945],[1.193,1.957],[1.189,2.071],[-0.492,2.067],[-0.602,2.082],[-0.601,1.902],[-0.5,1.871],[-0.023,1.872],[0.068,1.775],[0.068,1.657],[0.017,1.599],[-0.609,1.597],[-0.62,1.585],[-0.616,1.558],[-0.581,1.554]],"left":[[-0.892,1.026],[-0.885,0.837],[-0.841,0.736],[-0.772,0.681],[-0.677,0.689],[-0.608,0.562],[-0.474,0.413],[-0.252,0.272],[-0.237,-0.186],[-0.219,-0.226],[-0.117,-0.233],[0.213,-0.229],[0.206,-0.091],[0.224,-0.116],[0.228,-0.076],[0.257,-0.084],[0.242,-0.011],[0.256,-0.011],[0.256,0.2],[0.267,0.211],[0.739,0.211],[3.913,0.193],[6.171,0.21],[6.175,-0.091],[6.204,-0.149],[6.288,-0.218],[6.331,-0.232],[6.447,-0.232],[6.556,-0.181],[6.611,-0.105],[6.618,0.207],[6.643,0.291],[6.672,0.291],[6.701,0.262],[6.73,0.284],[6.752,0.255],[6.781,0.284],[6.817,0.255],[6.839,0.284],[6.861,0.255],[6.897,0.284],[6.919,0.255],[6.955,0.284],[6.984,0.255],[7.06,0.317],[7.096,0.513],[7.111,0.84],[7.096,1.246],[7.059,1.442],[7.004,1.497],[6.975,1.475],[6.954,1.504],[6.939,1.504],[6.925,1.475],[6.888,1.504],[6.867,1.467],[6.837,1.504],[6.808,1.467],[6.787,1.504],[6.75,1.467],[6.729,1.504],[6.7,1.467],[6.631,1.471],[6.637,2.059],[6.619,2.092],[6.161,2.091],[6.172,2.08],[6.136,2.058],[6.129,2.037],[6.143,2.022],[6.103,1.989],[5.973,1.996],[5.951,2.091],[5.769,2.091],[5.766,2.029],[5.751,2.043],[5.74,1.989],[5.595,1.989],[5.562,2],[5.562,2.065],[5.544,2.09],[5.363,2.09],[5.366,2.007],[5.348,1.996],[5.167,1.995],[5.145,2.09],[4.978,2.097],[4.952,2.057],[4.967,2.05],[4.967,1.999],[4.945,1.992],[4.963,1.966],[4.949,1.966],[4.934,1.995],[4.76,1.995],[4.756,2.071],[4.738,2.089],[4.571,2.096],[4.557,1.966],[4.535,1.995],[4.528,1.966],[4.52,1.995],[4.361,1.995],[4.357,2.063],[4.339,2.089],[4.172,2.089],[4.157,1.965],[4.15,1.987],[4.099,1.987],[3.969,1.987],[3.961,1.965],[3.939,2.096],[3.765,2.081],[3.751,1.965],[3.725,1.968],[3.747,1.976],[3.743,1.987],[3.591,1.994],[3.569,1.986],[3.562,1.965],[3.54,2.088],[3.366,2.08],[3.351,1.986],[3.17,1.986],[3.162,1.971],[3.151,2.077],[3.126,2.087],[2.966,2.08],[2.963,1.996],[2.908,1.978],[2.785,1.985],[2.778,2],[2.77,1.978],[2.752,1.996],[2.748,2.08],[2.567,2.08],[2.556,1.981],[2.48,1.978],[2.356,1.992],[2.349,2.079],[2.175,2.079],[2.153,1.977],[2.051,1.977],[2.008,1.977],[1.975,1.995],[1.971,2.013],[1.953,1.995],[1.95,2.079],[1.768,2.079],[1.754,1.984],[1.645,1.977],[1.598,2.002],[1.587,2.064],[1.554,2.06],[1.572,2.086],[1.376,2.078],[1.347,1.955],[1.329,1.958],[1.333,1.976],[1.224,1.984],[1.198,2.06],[1.162,2.06],[1.173,2.085],[-0.599,2.076],[-0.603,1.905],[-0.592,1.894],[-0.505,1.873],[-0.04,1.873],[0.058,1.782],[0.051,1.652],[-0.01,1.59],[-0.591,1.589],[-0.599,1.56],[-0.671,1.553],[-0.711,1.259],[-0.765,1.248],[-0.827,1.2],[-0.863,1.135]]},"features":{"side":{},"left":{"cam_pin_pad":[[[4.684,1.646],[4.646,1.641],[4.612,1.627],[4.582,1.603],[4.559,1.574],[4.544,1.539],[4.539,1.501],[4.54,1.178],[4.543,1.152],[4.553,1.127],[4.569,1.106],[4.59,1.09],[4.615,1.08],[4.641,1.076],[5.556,1.077],[5.582,1.081],[5.607,1.091],[5.628,1.107],[5.644,1.128],[5.654,1.153],[5.658,1.179],[5.657,1.502],[5.652,1.54],[5.638,1.575],[5.614,1.605],[5.585,1.628],[5.55,1.642],[5.512,1.647]]],"latch_slot":[[[0.4,1.813],[0.386,1.863],[0.349,1.9],[0.299,1.913],[0.248,1.9],[0.211,1.863],[0.198,1.812],[0.198,1.611],[0.212,1.56],[0.248,1.524],[0.299,1.51],[0.349,1.524],[0.386,1.561],[0.4,1.611]]]}},"placement":{"side":{"plane":"xy","offset":{}},"left":{"plane":"xy","offset":{}}},"bounds":{"min":[-1.0082,-0.216,-0.622],"max":[7.036,2.09,1.4787]},"volume_in3":4.9682,"centroid":[3.0383,0.9841,0.098],"shell":[3.0855,1.0562,0.0983],"area_in2":90.4069,"triangles":30568,"manifold":true,"rear_corner":{"r":0.75,"centre":[0.122,0.9985],"x":[-0.628,-0.0116],"reach_z":0.696,"trough_r":0.5625},"slabs":[[-1.008,0.575,0.837,-0.625,1.18,1.479],[-0.625,0.265,-0.595,-0.242,2.09,1.354],[-0.242,-0.216,-0.595,0.141,2.09,1.281],[0.141,-0.216,-0.595,0.524,2.09,1.142],[0.524,0.249,-0.595,0.907,1.972,1.002],[0.907,0.249,-0.595,1.29,1.972,0.863],[1.29,0.249,-0.595,1.673,1.972,0.723],[1.673,0.249,-0.595,2.056,1.972,0.595],[2.056,0.249,-0.595,2.822,1.972,1.245],[2.822,0.249,-0.595,5.887,1.972,0.826],[5.887,-0.186,-0.595,6.27,1.972,0.826],[6.27,-0.216,-0.622,6.653,1.972,0.754],[6.653,0.256,-0.622,7.036,1.5,0.622]],"slots":["receiver","hardware"]},"bcm-mcmr-10-handguard":{"part":"bcm-mcmr-10-handguard","model":"bcm-mcmr-10-handguard.glb","script":"bcm_mcmr_10_handguard.py","inputs":{"bcm-mcmr-10-handguard.cross_bolt0_from_rail_slot0":0.144,"bcm-mcmr-10-handguard.cross_bolt_above_bore":0.6,"bcm-mcmr-10-handguard.cross_bolt_d":0.18,"bcm-mcmr-10-handguard.cross_bolt_spacing":0.219,"bcm-mcmr-10-handguard.flare_bottom_run":0.36,"bcm-mcmr-10-handguard.flare_face_bottom":0.63,"bcm-mcmr-10-handguard.flare_tip_bottom":-0.28,"bcm-mcmr-10-handguard.flare_tip_top":0.31,"bcm-mcmr-10-handguard.hole_center_above_bore":0.76,"bcm-mcmr-10-handguard.hole_count":11,"bcm-mcmr-10-handguard.hole_oblong0_from_rail_slot0":0.96,"bcm-mcmr-10-handguard.hole_oblong_length":0.39,"bcm-mcmr-10-handguard.hole_oblong_slant":58,"bcm-mcmr-10-handguard.hole_oblong_width":0.2,"bcm-mcmr-10-handguard.hole_pitch":0.787,"bcm-mcmr-10-handguard.hole_round_d":0.19,"bcm-mcmr-10-handguard.inside_diameter":1.3,"bcm-mcmr-10-handguard.length":10.5,"bcm-mcmr-10-handguard.mlok_bottom_slot0_x":2.731,"bcm-mcmr-10-handguard.mlok_bottom_slots":5,"bcm-mcmr-10-handguard.mlok_diag_slot0_x":2.333,"bcm-mcmr-10-handguard.mlok_diag_slots":5,"bcm-mcmr-10-handguard.mlok_side_slot0_x":2.724,"bcm-mcmr-10-handguard.mlok_side_slots":5,"bcm-mcmr-10-handguard.neck_base_above_bore":0.71,"bcm-mcmr-10-handguard.neck_width":0.7013,"bcm-mcmr-10-handguard.rail_bevel":0.08,"bcm-mcmr-10-handguard.rail_body_height":0.215,"bcm-mcmr-10-handguard.rail_front_from_last_slot":0.28,"bcm-mcmr-10-handguard.rail_slot0_from_rear":0.607,"bcm-mcmr-10-handguard.rail_slot0_x":0.185,"bcm-mcmr-10-handguard.rail_slots":25,"bcm-mcmr-10-handguard.rail_top_above_bore":1.2,"bcm-mcmr-10-handguard.rear_x":-0.4225,"bcm-mcmr-10-handguard.width":1.5,"std.mlok.slot_corner_r":0.0937007874015748,"std.mlok.slot_length":1.2598425196850394,"std.mlok.slot_pitch":1.574803149606299,"std.mlok.slot_width":0.2755905511811024,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{},"bounds":{"min":[-0.4225,-0.75,-0.75],"max":[10.0775,1.2,0.75]},"volume_in3":5.1632,"centroid":[4.421,0.3385,0],"shell":[4.6018,0.2411,0],"area_in2":103.7517,"triangles":25172,"manifold":true,"slabs":[[-0.423,-0.75,-0.75,10.078,1.2,0.75]],"slots":["body","bolts"]},"bcm-mcmr-13-handguard":{"part":"bcm-mcmr-13-handguard","model":"bcm-mcmr-13-handguard.glb","script":"bcm_mcmr_13_handguard.py","inputs":{"bcm-mcmr-13-handguard.cross_bolt0_from_rail_slot0":0.15,"bcm-mcmr-13-handguard.cross_bolt_above_bore":0.6,"bcm-mcmr-13-handguard.cross_bolt_d":0.18,"bcm-mcmr-13-handguard.cross_bolt_spacing":0.219,"bcm-mcmr-13-handguard.flare_bottom_run":0.35,"bcm-mcmr-13-handguard.flare_face_bottom":0.74,"bcm-mcmr-13-handguard.flare_tip_bottom":-0.32,"bcm-mcmr-13-handguard.flare_tip_top":0.26,"bcm-mcmr-13-handguard.hole_center_above_bore":0.76,"bcm-mcmr-13-handguard.hole_count":15,"bcm-mcmr-13-handguard.hole_oblong0_from_rail_slot0":0.728,"bcm-mcmr-13-handguard.hole_oblong_length":0.39,"bcm-mcmr-13-handguard.hole_oblong_slant":58,"bcm-mcmr-13-handguard.hole_oblong_width":0.2,"bcm-mcmr-13-handguard.hole_pitch":0.786,"bcm-mcmr-13-handguard.hole_round_d":0.19,"bcm-mcmr-13-handguard.inside_diameter":1.3,"bcm-mcmr-13-handguard.length":13.4,"bcm-mcmr-13-handguard.mlok_bottom_slot0_x":2.509,"bcm-mcmr-13-handguard.mlok_bottom_slots":7,"bcm-mcmr-13-handguard.mlok_diag_slot0_x":2.101,"bcm-mcmr-13-handguard.mlok_diag_slots":7,"bcm-mcmr-13-handguard.mlok_side_slot0_x":2.502,"bcm-mcmr-13-handguard.mlok_side_slots":7,"bcm-mcmr-13-handguard.neck_base_above_bore":0.71,"bcm-mcmr-13-handguard.neck_width":0.7013,"bcm-mcmr-13-handguard.rail_bevel":0.08,"bcm-mcmr-13-handguard.rail_body_height":0.215,"bcm-mcmr-13-handguard.rail_front_from_last_slot":0.279,"bcm-mcmr-13-handguard.rail_slot0_from_rear":0.63,"bcm-mcmr-13-handguard.rail_slot0_x":0.186,"bcm-mcmr-13-handguard.rail_slots":32,"bcm-mcmr-13-handguard.rail_top_above_bore":1.2,"bcm-mcmr-13-handguard.rear_x":-0.4225,"bcm-mcmr-13-handguard.width":1.5,"std.mlok.slot_corner_r":0.0937007874015748,"std.mlok.slot_length":1.2598425196850394,"std.mlok.slot_pitch":1.574803149606299,"std.mlok.slot_width":0.2755905511811024,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{},"bounds":{"min":[-0.4225,-0.75,-0.75],"max":[12.9775,1.2,0.75]},"volume_in3":6.3589,"centroid":[5.8378,0.3455,0],"shell":[6.025,0.2401,0],"area_in2":129.9502,"triangles":33800,"manifold":true,"slabs":[[-0.423,-0.75,-0.75,12.977,1.2,0.75]],"slots":["body","bolts"]},"bcm-mcmr-15-handguard":{"part":"bcm-mcmr-15-handguard","model":"bcm-mcmr-15-handguard.glb","script":"bcm_mcmr_15_handguard.py","inputs":{"bcm-mcmr-15-handguard.cross_bolt0_from_rail_slot0":0.152,"bcm-mcmr-15-handguard.cross_bolt_above_bore":0.6,"bcm-mcmr-15-handguard.cross_bolt_d":0.18,"bcm-mcmr-15-handguard.cross_bolt_spacing":0.217,"bcm-mcmr-15-handguard.hole_center_above_bore":0.76,"bcm-mcmr-15-handguard.hole_count":16,"bcm-mcmr-15-handguard.hole_oblong0_from_rail_slot0":1.543,"bcm-mcmr-15-handguard.hole_oblong_length":0.39,"bcm-mcmr-15-handguard.hole_oblong_slant":58,"bcm-mcmr-15-handguard.hole_oblong_width":0.2,"bcm-mcmr-15-handguard.hole_pitch":0.788,"bcm-mcmr-15-handguard.hole_round_d":0.19,"bcm-mcmr-15-handguard.inside_diameter":1.3,"bcm-mcmr-15-handguard.length":15,"bcm-mcmr-15-handguard.mlok_bottom_slot0_x":2.539,"bcm-mcmr-15-handguard.mlok_bottom_slots":8,"bcm-mcmr-15-handguard.mlok_diag_slot0_x":2.142,"bcm-mcmr-15-handguard.mlok_diag_slots":8,"bcm-mcmr-15-handguard.mlok_side_slot0_x":2.532,"bcm-mcmr-15-handguard.mlok_side_slots":8,"bcm-mcmr-15-handguard.neck_base_above_bore":0.71,"bcm-mcmr-15-handguard.neck_width":0.7013,"bcm-mcmr-15-handguard.rail_bevel":0.08,"bcm-mcmr-15-handguard.rail_body_height":0.215,"bcm-mcmr-15-handguard.rail_front_from_last_slot":0.283,"bcm-mcmr-15-handguard.rail_slot0_from_rear":0.623,"bcm-mcmr-15-handguard.rail_slot0_x":0.19,"bcm-mcmr-15-handguard.rail_slots":36,"bcm-mcmr-15-handguard.rail_top_above_bore":1.2,"bcm-mcmr-15-handguard.rear_x":-0.4225,"bcm-mcmr-15-handguard.width":1.5,"std.mlok.slot_corner_r":0.0937007874015748,"std.mlok.slot_length":1.2598425196850394,"std.mlok.slot_pitch":1.574803149606299,"std.mlok.slot_width":0.2755905511811024,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{"side":[[0,-0.974],[0,-1.458],[0.013,-1.472],[0.013,-1.566],[0.027,-1.579],[0.04,-1.7],[0.081,-1.808],[0.134,-1.848],[0.148,-1.915],[0.168,-1.935],[0.276,-1.962],[0.329,-1.949],[0.343,-1.962],[4.845,-1.962],[4.859,-1.976],[11.915,-1.976],[11.929,-1.962],[14.59,-1.962],[14.852,-1.7],[14.987,-1.539],[15,-1.499],[15,-0.961],[14.785,-0.733],[14.61,-0.491],[14.597,-0.45],[14.597,-0.235],[14.61,-0.222],[14.61,-0.074],[14.59,-0.054],[14.267,-0.054],[14.241,-0.067],[14.214,-0.04],[14.066,-0.04],[14.052,-0.054],[13.905,-0.054],[13.878,-0.094],[13.851,-0.04],[13.676,-0.04],[13.663,-0.054],[13.542,-0.054],[13.501,-0.108],[13.474,-0.04],[13.273,-0.04],[13.259,-0.054],[13.165,-0.054],[13.138,-0.134],[13.118,-0.114],[13.118,-0.074],[13.098,-0.04],[12.856,-0.04],[12.802,-0.054],[12.782,-0.074],[12.782,-0.114],[12.762,-0.148],[12.742,-0.128],[12.742,-0.074],[12.722,-0.04],[12.695,-0.027],[12.574,-0.027],[12.56,-0.04],[12.426,-0.054],[12.406,-0.074],[12.406,-0.128],[12.372,-0.148],[12.352,-0.047],[12.332,-0.027],[12.184,-0.027],[12.171,-0.04],[12.09,-0.04],[12.063,-0.054],[12.03,-0.141],[11.996,-0.148],[11.976,-0.128],[11.956,-0.027],[11.794,-0.027],[11.781,-0.04],[11.7,-0.04],[11.653,-0.141],[11.606,-0.148],[11.586,-0.101],[11.586,-0.047],[11.566,-0.027],[11.405,-0.027],[11.324,-0.054],[11.297,-0.121],[11.27,-0.148],[11.23,-0.148],[11.196,-0.101],[11.19,-0.027],[11.015,-0.027],[10.974,-0.04],[10.907,-0.134],[10.84,-0.148],[10.806,-0.087],[10.8,-0.027],[10.625,-0.027],[10.544,-0.134],[10.437,-0.134],[10.41,-0.027],[10.262,-0.013],[10.242,-0.034],[10.242,-0.074],[10.208,-0.054],[10.202,-0.087],[10.155,-0.134],[10.047,-0.134],[10.027,-0.087],[10.027,-0.034],[10.007,-0.013],[9.859,-0.013],[9.852,-0.047],[9.778,-0.134],[9.657,-0.134],[9.637,-0.087],[9.637,-0.034],[9.617,-0.013],[9.469,-0.013],[9.449,-0.034],[9.462,-0.047],[9.456,-0.121],[9.442,-0.108],[9.388,-0.134],[9.267,-0.134],[9.247,-0.114],[9.247,-0.034],[9.227,-0.013],[9.079,-0.013],[9.059,-0.047],[9.073,-0.087],[9.039,-0.134],[8.864,-0.134],[8.858,-0.034],[8.837,-0.013],[8.69,-0.013],[8.669,-0.034],[8.663,-0.121],[8.636,-0.134],[8.474,-0.134],[8.454,-0.101],[8.448,-0.013],[8.286,-0.013],[8.273,-0.121],[8.246,-0.134],[8.085,-0.134],[8.065,-0.114],[8.058,-0.013],[7.897,-0.013],[7.89,-0.101],[7.856,-0.134],[7.695,-0.134],[7.661,-0.087],[7.655,-0.013],[7.493,-0.013],[7.487,-0.114],[7.466,-0.134],[7.332,-0.134],[7.319,-0.121],[7.305,-0.134],[7.272,-0.114],[7.265,-0.013],[7.103,-0.013],[7.09,-0.121],[6.956,-0.134],[6.882,-0.114],[6.882,-0.034],[6.835,0],[6.821,-0.013],[6.714,-0.013],[6.694,-0.074],[6.707,-0.087],[6.687,-0.121],[6.485,-0.121],[6.472,-0.013],[6.337,-0.013],[6.324,0],[6.304,-0.02],[6.304,-0.101],[6.284,-0.121],[6.095,-0.121],[6.089,-0.02],[6.042,0],[6.028,-0.013],[5.921,-0.013],[5.894,-0.121],[5.692,-0.121],[5.685,-0.02],[5.665,0],[5.544,0],[5.511,-0.02],[5.511,-0.101],[5.491,-0.121],[5.302,-0.121],[5.296,-0.02],[5.276,0],[5.141,0],[5.108,-0.047],[5.101,-0.121],[4.913,-0.121],[4.892,-0.087],[4.906,-0.02],[4.886,0],[4.738,0],[4.718,-0.02],[4.718,-0.087],[4.698,-0.121],[4.536,-0.121],[4.496,0],[4.348,0],[4.328,-0.02],[4.308,-0.121],[4.173,-0.121],[4.093,0],[3.945,0],[3.925,-0.034],[3.918,-0.121],[3.784,-0.121],[3.703,0],[3.569,0],[3.535,-0.02],[3.535,-0.087],[3.515,-0.121],[3.407,-0.121],[3.374,-0.06],[3.313,0],[3.165,0],[3.132,-0.06],[3.125,-0.121],[3.031,-0.121],[2.997,-0.047],[2.923,0],[2.776,0],[2.742,-0.06],[2.742,-0.114],[2.668,-0.121],[2.621,-0.047],[2.574,-0.013],[2.386,0],[2.352,-0.047],[2.339,-0.114],[2.292,-0.121],[2.258,-0.06],[2.198,-0.013],[2.077,0],[2.063,-0.013],[2.05,0],[2.036,-0.013],[1.996,0],[1.962,-0.047],[1.949,-0.114],[1.915,-0.121],[1.895,-0.074],[1.848,-0.027],[1.741,0],[1.606,0],[1.573,-0.047],[1.573,-0.087],[1.552,-0.121],[1.519,-0.101],[1.519,-0.06],[1.485,-0.027],[1.431,-0.013],[1.203,-0.013],[1.163,-0.121],[1.122,-0.04],[1.028,-0.013],[0.813,-0.013],[0.786,-0.108],[0.766,-0.087],[0.759,-0.04],[0.652,-0.027],[0.638,-0.013],[0.114,-0.013],[0.094,-0.06],[0.094,-0.141],[0.128,-0.175],[0.329,-0.175],[0.349,-0.235],[0.329,-0.255],[0.128,-0.255],[0.108,-0.289],[0.108,-0.41],[0.128,-0.444],[0.343,-0.444],[0.349,-0.491],[0.336,-0.531],[0.302,-0.551],[0.101,-0.551],[0.081,-0.571],[0.081,-0.612],[0.04,-0.719],[0.04,-0.773],[0.013,-0.853],[0.013,-0.961]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"x":"rear_x","y":"rail_top_above_bore"}}},"bounds":{"min":[-0.4225,-0.75,-0.75],"max":[14.5775,1.2,0.75]},"volume_in3":7.3022,"centroid":[6.406,0.3627,0],"shell":[6.8173,0.2383,0],"area_in2":144.3129,"triangles":37112,"manifold":true,"slabs":[[-0.423,-0.75,-0.75,14.578,1.2,0.75]],"slots":["body","bolts"]},"bcm-mk2-buffer-t0":{"part":"bcm-mk2-buffer-t0","model":"bcm-mk2-buffer-t0.glb","script":"bcm_mk2_buffer_t0.py","inputs":{"bcm-mk2-buffer-t0.body_length":3.646,"bcm-mk2-buffer-t0.bumper_exposed":0.4,"bcm-mk2-buffer-t0.collar_d":0.781,"bcm-mk2-buffer-t0.head_thickness":0.254,"bcm-mk2-buffer-t0.length":4.046,"bcm-mk2-buffer-t0.od":0.98,"bcm-mk2-buffer-t0.pin_d":0.09,"bcm-mk2-buffer-t0.pin_from_open_end":0.144,"std.carbine_buffer.body_d":0.687,"std.carbine_buffer.body_start":0.5145,"std.carbine_buffer.bumper_band":0.06,"std.carbine_buffer.bumper_d":0.687,"std.carbine_buffer.bumper_taper":13.5,"std.carbine_buffer.head_flat_across":0.952,"std.carbine_buffer.head_rim":0.214,"std.carbine_buffer.pilot_end":0.468},"profiles":{},"bounds":{"min":[0,-0.49,-0.49],"max":[4.046,0.462,0.49]},"volume_in3":1.5886,"centroid":[1.8557,0,0],"shell":[1.9869,0,0],"area_in2":11.2456,"triangles":7276,"manifold":true,"slabs":[[0,-0.49,-0.49,0.368,0.462,0.49],[0.368,-0.391,-0.391,4.046,0.391,0.391]],"slots":["body","bumper","pin"]},"bcm-mk2-charging-handle":{"part":"bcm-mk2-charging-handle","model":"bcm-mk2-charging-handle.glb","script":"bcm_mk2_charging_handle.py","inputs":{"bcm-mk2-charging-handle.channel_depth":0.25,"bcm-mk2-charging-handle.channel_width":0.312,"bcm-mk2-charging-handle.guide_lug_height":0.119,"bcm-mk2-charging-handle.hook_drop":0.275,"bcm-mk2-charging-handle.hook_fillet_r":0.187,"bcm-mk2-charging-handle.hook_length":0.295,"bcm-mk2-charging-handle.hub_r":0.25,"bcm-mk2-charging-handle.latch_front_height":0.23,"bcm-mk2-charging-handle.latch_thickness":0.278,"bcm-mk2-charging-handle.length":5.895,"bcm-mk2-charging-handle.pin_behind_shoulder":0.368,"bcm-mk2-charging-handle.pin_d":0.092,"bcm-mk2-charging-handle.pin_off_centre":0.257,"bcm-mk2-charging-handle.rib_count":10,"bcm-mk2-charging-handle.rib_depth":0.02,"bcm-mk2-charging-handle.rib_first_z":0.58,"bcm-mk2-charging-handle.rib_pitch":0.06,"bcm-mk2-charging-handle.shaft_thickness":0.2985,"bcm-mk2-charging-handle.shaft_width":0.4,"bcm-mk2-charging-handle.t_height":0.33,"bcm-mk2-charging-handle.top_chamfer_drop":0.076,"bcm-mk2-charging-handle.top_chamfer_from_shoulder":0.235,"bcm-mk2-charging-handle.top_flat_width":0.14,"std.ar15.charging_handle_axis_y":1.7338,"std.ar15.charging_handle_channel_rear_half_width":0.209,"std.ar15.charging_handle_channel_rear_round_x":0.676,"std.ar15.charging_handle_channel_round_r":0.2665,"std.ar15.charging_handle_latch_slot_bottom_y":1.52,"std.ar15.charging_handle_latch_slot_floor":0.045,"std.ar15.charging_handle_latch_slot_length":0.195,"std.ar15.charging_handle_latch_slot_top_y":1.935,"std.ar15.charging_handle_latch_slot_wall":0.156,"std.ar15.charging_handle_notch_chamfer":0.083,"std.ar15.charging_handle_notch_floor_y":1.571,"std.ar15.charging_handle_notch_roof_y":1.89,"std.ar15.rail_tongue_half_width":0.318},"profiles":{"plan":[[-1.014,0.007],[-1.009,-0.079],[-0.985,-0.107],[-0.974,-0.142],[-0.974,-0.176],[-0.985,-0.199],[-0.98,-0.211],[-0.98,-0.279],[-0.985,-0.285],[-0.98,-0.291],[-0.985,-0.308],[-0.98,-0.383],[-0.991,-0.412],[-0.985,-0.434],[-0.997,-0.446],[-0.997,-0.475],[-0.962,-0.584],[-0.916,-0.664],[-0.889,-0.689],[-0.823,-0.715],[-0.811,-0.761],[-0.77,-0.818],[-0.759,-0.858],[-0.73,-0.881],[-0.724,-0.909],[-0.701,-0.921],[-0.695,-0.949],[-0.666,-0.972],[-0.666,-0.995],[-0.637,-1.012],[-0.631,-1.046],[-0.498,-1.234],[-0.425,-1.288],[-0.356,-1.311],[-0.263,-1.31],[-0.223,-1.292],[-0.191,-1.255],[-0.185,-1.198],[-0.202,-1.158],[-0.249,-1.124],[-0.237,-1.107],[-0.272,-1.084],[-0.266,-1.055],[-0.301,-1.021],[-0.295,-0.992],[-0.315,-0.984],[-0.324,-0.97],[-0.312,-0.947],[-0.341,-0.918],[-0.341,-0.907],[-0.33,-0.895],[-0.359,-0.861],[-0.347,-0.832],[-0.37,-0.81],[-0.37,-0.798],[-0.359,-0.792],[-0.359,-0.77],[-0.376,-0.764],[-0.382,-0.747],[-0.364,-0.735],[-0.364,-0.718],[-0.387,-0.701],[-0.387,-0.689],[-0.37,-0.678],[-0.37,-0.661],[-0.387,-0.649],[-0.387,-0.632],[-0.37,-0.621],[-0.37,-0.598],[-0.387,-0.592],[-0.387,-0.575],[-0.37,-0.563],[-0.359,-0.523],[-0.321,-0.486],[-0.292,-0.474],[-0.234,-0.474],[-0.199,-0.485],[0.182,-0.472],[0.291,-0.443],[0.32,-0.431],[0.34,-0.411],[0.346,-0.297],[0.34,-0.268],[0.32,-0.243],[0.28,-0.22],[0.199,-0.22],[0.185,-0.235],[0.19,-0.303],[0.182,-0.318],[0.164,-0.323],[0.014,-0.324],[0,-0.31],[0,-0.207],[0.02,-0.198],[0.188,-0.198],[0.193,-0.203],[0.608,-0.196],[0.614,-0.202],[4.571,-0.198],[4.654,-0.237],[4.877,-0.237],[4.927,-0.208],[4.966,-0.197],[5.847,-0.199],[5.869,-0.188],[5.927,-0.118],[5.955,-0.017],[5.944,0.072],[5.916,0.134],[5.869,0.187],[5.847,0.198],[4.988,0.196],[4.983,0.202],[4.977,0.196],[4.972,0.202],[4.938,0.196],[4.936,0.204],[4.944,0.213],[4.849,0.246],[4.666,0.246],[4.615,0.218],[4.579,0.209],[4.621,0.206],[4.621,0.201],[4.42,0.2],[4.415,0.195],[4.409,0.2],[4.32,0.194],[4.314,0.2],[2.327,0.196],[2.315,0.201],[2.31,0.196],[2.23,0.196],[2.219,0.201],[2.207,0.195],[2.202,0.201],[0.159,0.197],[0.153,0.202],[0.009,0.202],[0,0.211],[0,0.314],[-0.009,0.322],[-0.026,0.322],[-0.032,0.334],[-0.052,0.336],[-0.052,0.365],[-0.066,0.379],[-0.211,0.396],[-0.269,0.413],[-0.335,0.473],[-0.359,0.531],[-0.359,0.553],[-0.382,0.576],[-0.382,0.588],[-0.364,0.605],[-0.364,0.622],[-0.382,0.634],[-0.382,0.645],[-0.364,0.662],[-0.376,0.702],[-0.359,0.714],[-0.359,0.737],[-0.37,0.742],[-0.37,0.76],[-0.356,0.763],[-0.347,0.783],[-0.359,0.8],[-0.359,0.817],[-0.335,0.84],[-0.347,0.851],[-0.347,0.868],[-0.324,0.886],[-0.324,0.903],[-0.335,0.914],[-0.306,0.943],[-0.312,0.977],[-0.289,0.989],[-0.283,1.006],[-0.289,1.029],[-0.26,1.052],[-0.266,1.08],[-0.237,1.097],[-0.231,1.137],[-0.202,1.149],[-0.179,1.195],[-0.179,1.246],[-0.191,1.269],[-0.223,1.301],[-0.257,1.312],[-0.35,1.312],[-0.396,1.301],[-0.442,1.278],[-0.503,1.224],[-0.619,1.058],[-0.625,1.023],[-0.66,0.995],[-0.66,0.972],[-0.689,0.949],[-0.695,0.92],[-0.724,0.903],[-0.724,0.88],[-0.753,0.857],[-0.759,0.828],[-0.776,0.817],[-0.811,0.76],[-0.823,0.731],[-0.823,0.708],[-0.86,0.699],[-0.889,0.682],[-0.939,0.622],[-0.974,0.553],[-0.997,0.473],[-0.997,0.438],[-0.985,0.427],[-0.997,0.392],[-0.991,0.375],[-0.974,0.364],[-0.974,0.341],[-0.985,0.318],[-0.98,0.306],[-0.985,0.272],[-0.98,0.249],[-0.98,0.105],[-0.985,0.094],[-0.98,0.088],[-1.009,0.048]]},"features":{"plan":{"rear_grip":[[[-0.564,0.72],[-0.692,0.737],[-0.82,0.719],[-0.924,0.662],[-0.977,0.576],[-1,0.432],[-1.012,0.26],[-1.017,0.002],[-1.012,-0.257],[-1,-0.429],[-0.977,-0.572],[-0.924,-0.664],[-0.82,-0.721],[-0.692,-0.737],[-0.564,-0.725],[-0.489,-0.684],[-0.46,-0.598],[-0.46,-0.426],[-0.518,-0.386],[-0.605,-0.341],[-0.669,-0.255],[-0.727,-0.141],[-0.75,0.003],[-0.727,0.146],[-0.669,0.261],[-0.605,0.347],[-0.518,0.393],[-0.46,0.422],[-0.46,0.605],[-0.489,0.685]]]}},"placement":{"plan":{"plane":"xz","offset":{}}},"bounds":{"min":[-1.014,-0.4243,-1.311],"max":[5.895,0.1807,1.312]},"volume_in3":0.7966,"centroid":[0.8011,-0.0006,-0.0109],"shell":[1.809,0.0004,-0.0091],"area_in2":16.1274,"triangles":13794,"manifold":true,"slabs":[[-1.014,-0.149,-1.047,-0.63,0.181,1.019],[-0.63,-0.149,-1.311,0.137,0.181,1.312],[0.137,-0.149,-0.473,0.521,0.149,0.202],[0.521,-0.177,-0.237,5.511,0.149,0.246],[5.511,-0.424,-0.2,5.895,0.149,0.2]],"slots":["body","pins"]},"bcm-mk2-lower-receiver.guard":{"part":"bcm-mk2-lower-receiver","component":"guard","model":"bcm-mk2-lower-receiver.guard.glb","script":"bcm_mk2_lower_receiver.py","inputs":{"bcm-mk2-lower-receiver.bolt_catch_boss_bottom_y":-0.154,"bcm-mk2-lower-receiver.bolt_catch_boss_front_x":3.617,"bcm-mk2-lower-receiver.bolt_catch_boss_rear_x":3.091,"bcm-mk2-lower-receiver.bolt_catch_gap_front_x":3.375,"bcm-mk2-lower-receiver.bolt_catch_gap_rear_x":3.203,"bcm-mk2-lower-receiver.buffer_axis_above_pin":0.8775,"bcm-mk2-lower-receiver.fence_bottom_y":-1.015,"bcm-mk2-lower-receiver.fence_corner_r":0.06,"bcm-mk2-lower-receiver.fence_rear_x":2.864,"bcm-mk2-lower-receiver.fence_top_y":-0.202,"bcm-mk2-lower-receiver.front_ahead_of_pin":6.568,"bcm-mk2-lower-receiver.front_ear_bottom_y":-2.288,"bcm-mk2-lower-receiver.grip_seat_y":-1.0695,"bcm-mk2-lower-receiver.guard_edge_r":0.03,"bcm-mk2-lower-receiver.guard_front_end_x":3.47,"bcm-mk2-lower-receiver.guard_rear_end_x":1.3,"bcm-mk2-lower-receiver.guard_tab_top_y":-2.03,"bcm-mk2-lower-receiver.guard_width":0.442,"bcm-mk2-lower-receiver.hammer_pin_x":2.771,"bcm-mk2-lower-receiver.hammer_pin_y":-0.375,"bcm-mk2-lower-receiver.magwell_front_x":6.091,"bcm-mk2-lower-receiver.magwell_wall_curve_bottom_y_left":-1.317,"bcm-mk2-lower-receiver.magwell_wall_curve_top_y_left":-0.922,"bcm-mk2-lower-receiver.magwell_wall_rear_x":3.588,"bcm-mk2-lower-receiver.magwell_wall_rear_x_left":3.435,"bcm-mk2-lower-receiver.magwell_wall_upper_rear_x_left":3.03,"bcm-mk2-lower-receiver.rear_behind_pin":1.125,"bcm-mk2-lower-receiver.rear_ear_bottom_y":-2.333,"bcm-mk2-lower-receiver.selector_x":0.803,"bcm-mk2-lower-receiver.selector_y":-0.466,"bcm-mk2-lower-receiver.tower_front_x":-0.439,"bcm-mk2-lower-receiver.trigger_guard_front_x":3.3425,"bcm-mk2-lower-receiver.trigger_guard_front_y":-2.18,"bcm-mk2-lower-receiver.trigger_guard_rear_x":1.4985,"bcm-mk2-lower-receiver.trigger_guard_rear_y":-2.18,"bcm-mk2-lower-receiver.trigger_pin_x":1.928,"bcm-mk2-lower-receiver.trigger_pin_y":-0.689,"bcm-mk2-lower-receiver.well_roll_bottom_y":-0.202,"bcm-mk2-lower-receiver.well_roll_crest_out":0.8,"bcm-mk2-lower-receiver.well_roll_front_x":6.181,"bcm-mk2-lower-receiver.well_roll_rear_round":0.1,"bcm-mk2-lower-receiver.well_roll_rear_x":2.78,"bcm-mk2-lower-receiver.window_front_x":2.947,"bcm-mk2-lower-receiver.window_rear_x":1.68,"std.ar15.bolt_catch_boss_out":0.618,"std.ar15.bolt_catch_plunger_hole_d":0.156,"std.ar15.bolt_catch_plunger_hole_depth":0.4703,"std.ar15.bolt_catch_plunger_hole_y":-0.195,"std.ar15.bolt_catch_slot_bottom_y":-0.38,"std.ar15.bolt_catch_slot_floor":0.4409,"std.ar15.bolt_catch_slot_front_x":3.375,"std.ar15.bolt_catch_slot_width":0.172,"std.ar15.bore_axis_y":0.8775,"std.ar15.buffer_tower_front_x":-0.628,"std.ar15.buffer_tower_od":1.392,"std.ar15.deck_front_x":6.194,"std.ar15.deck_y":0.2485,"std.ar15.fcg_pin_hole_d":0.15675,"std.ar15.fcg_pocket_corner_r":0.218,"std.ar15.fcg_pocket_depth":1.249,"std.ar15.fcg_pocket_front_x":3.11,"std.ar15.fcg_pocket_length":2.87,"std.ar15.fcg_pocket_width":0.69,"std.ar15.front_lug_slot_width":0.5,"std.ar15.grip_lug_depth":0.93,"std.ar15.grip_lug_face_angle":60,"std.ar15.grip_lug_face_from_pin":1.228,"std.ar15.grip_lug_front_from_rear_face":2.3,"std.ar15.grip_lug_length":1.25,"std.ar15.grip_lug_width":0.375,"std.ar15.grip_seat_below_deck":1.318,"std.ar15.lower_body_width":0.88,"std.ar15.mag_catch_boss_edge_r":0.059,"std.ar15.mag_catch_boss_proud":0.0906,"std.ar15.mag_catch_boss_r":0.253,"std.ar15.mag_catch_boss_x":4.262,"std.ar15.mag_catch_cbore_d":0.312,"std.ar15.mag_catch_cbore_depth":0.25,"std.ar15.mag_catch_fence_out":0.549,"std.ar15.mag_catch_hole_d":0.2055,"std.ar15.mag_catch_slot_bottom_y":-0.689,"std.ar15.mag_catch_slot_floor":0.3799,"std.ar15.mag_catch_slot_front_x":4.557,"std.ar15.mag_catch_slot_h":0.252,"std.ar15.mag_catch_slot_rear_x":3.048,"std.ar15.mag_catch_x":3.291,"std.ar15.mag_catch_y":-0.565,"std.ar15.mag_release_pocket_depth":0.617,"std.ar15.mag_release_pocket_h":0.515,"std.ar15.mag_release_pocket_w":0.319,"std.ar15.magwell_band_bottom_y":-1.959,"std.ar15.magwell_band_front_x":4.549,"std.ar15.magwell_band_proud":0.059,"std.ar15.magwell_band_rear_x":3.975,"std.ar15.magwell_band_side":0.084,"std.ar15.magwell_box_length":2.398,"std.ar15.magwell_corner_r":0.062,"std.ar15.magwell_front_inner_x":6.025,"std.ar15.magwell_length":2.553,"std.ar15.magwell_outside_width":1.098,"std.ar15.magwell_spine_slot_width":0.47,"std.ar15.magwell_width":0.898,"std.ar15.pin_spacing":6.375,"std.ar15.pivot_hole_d":0.251,"std.ar15.rear_lug_slot_depth":0.63,"std.ar15.rear_lug_slot_rear_x":-0.402,"std.ar15.rear_lug_slot_width":0.5,"std.ar15.rear_underside_arc_center_below_seat":0.1928,"std.ar15.rear_underside_arc_center_x":-1.0238,"std.ar15.rear_underside_arc_r":0.75,"std.ar15.rear_underside_round_r":0.44,"std.ar15.rear_wall_arc_r":0.75,"std.ar15.receiver_rear_x":-1.125,"std.ar15.safety_detent_boss_below_deck":0.455,"std.ar15.safety_detent_boss_face":0.53,"std.ar15.safety_detent_boss_from_rear":0.36,"std.ar15.safety_detent_boss_length":0.43,"std.ar15.selector_hole_d":0.376,"std.ar15.takedown_hole_d":0.251,"std.ar15.takedown_spotface_d":0.44,"std.ar15.takedown_spotface_depth":0.04,"std.ar15.trigger_guard_ear_gap":0.442,"std.ar15.trigger_guard_ears_width":0.659,"std.ar15.trigger_guard_front_hole_d":0.1265,"std.ar15.trigger_guard_front_spotface_d":0.25,"std.ar15.trigger_guard_front_spotface_floor":0.3219,"std.ar15.trigger_guard_rear_hole_d":0.1285,"std.ar15.trigger_pin_x":1.928,"std.ar15.trigger_slot_front_ahead_of_pin":0.52,"std.ar15.trigger_slot_length":0.68,"std.ar15.trigger_slot_width":0.312,"std.ar15.upper_rear_face_x":-0.621,"std.receiver_extension.milspec_od":1.148},"profiles":{"guard":[[1.452,-2.092],[1.459,-2.357],[2.124,-2.451],[2.303,-2.456],[2.758,-2.427],[3.356,-2.31],[3.348,-2.009],[3.186,-2.153],[2.897,-2.284],[2.54,-2.348],[2.107,-2.325],[1.786,-2.24],[1.508,-2.088]]},"features":{"guard":{}},"placement":{"guard":{"plane":"xy","offset":{}}},"bounds":{"min":[1.3,-2.456,-0.221],"max":[3.47,-2.0097,0.221]},"volume_in3":0.1579,"centroid":[2.3184,-2.2855,0],"shell":[2.3696,-2.2751,0],"area_in2":3.3545,"triangles":2300,"manifold":true,"slabs":[[1.3,-2.386,-0.221,1.662,-2.03,0.221],[1.662,-2.437,-0.221,2.023,-2.172,0.221],[2.023,-2.456,-0.221,2.747,-2.303,0.221],[2.747,-2.428,-0.221,3.108,-2.188,0.221],[3.108,-2.358,-0.221,3.47,-2.01,0.221]],"slots":["guard"]},"bcm-mk2-lower-receiver.receiver":{"part":"bcm-mk2-lower-receiver","component":"receiver","model":"bcm-mk2-lower-receiver.receiver.glb","script":"bcm_mk2_lower_receiver.py","inputs":{"bcm-mk2-lower-receiver.bolt_catch_boss_bottom_y":-0.154,"bcm-mk2-lower-receiver.bolt_catch_boss_front_x":3.617,"bcm-mk2-lower-receiver.bolt_catch_boss_rear_x":3.091,"bcm-mk2-lower-receiver.bolt_catch_gap_front_x":3.375,"bcm-mk2-lower-receiver.bolt_catch_gap_rear_x":3.203,"bcm-mk2-lower-receiver.buffer_axis_above_pin":0.8775,"bcm-mk2-lower-receiver.fence_bottom_y":-1.015,"bcm-mk2-lower-receiver.fence_corner_r":0.06,"bcm-mk2-lower-receiver.fence_rear_x":2.864,"bcm-mk2-lower-receiver.fence_top_y":-0.202,"bcm-mk2-lower-receiver.front_ahead_of_pin":6.568,"bcm-mk2-lower-receiver.front_ear_bottom_y":-2.288,"bcm-mk2-lower-receiver.grip_seat_y":-1.0695,"bcm-mk2-lower-receiver.hammer_pin_x":2.771,"bcm-mk2-lower-receiver.hammer_pin_y":-0.375,"bcm-mk2-lower-receiver.magwell_front_x":6.091,"bcm-mk2-lower-receiver.magwell_wall_curve_bottom_y_left":-1.317,"bcm-mk2-lower-receiver.magwell_wall_curve_top_y_left":-0.922,"bcm-mk2-lower-receiver.magwell_wall_rear_x":3.588,"bcm-mk2-lower-receiver.magwell_wall_rear_x_left":3.435,"bcm-mk2-lower-receiver.magwell_wall_upper_rear_x_left":3.03,"bcm-mk2-lower-receiver.rear_behind_pin":1.125,"bcm-mk2-lower-receiver.rear_ear_bottom_y":-2.333,"bcm-mk2-lower-receiver.selector_x":0.803,"bcm-mk2-lower-receiver.selector_y":-0.466,"bcm-mk2-lower-receiver.tower_front_x":-0.439,"bcm-mk2-lower-receiver.trigger_guard_front_x":3.3425,"bcm-mk2-lower-receiver.trigger_guard_front_y":-2.18,"bcm-mk2-lower-receiver.trigger_guard_rear_x":1.4985,"bcm-mk2-lower-receiver.trigger_guard_rear_y":-2.18,"bcm-mk2-lower-receiver.trigger_pin_x":1.928,"bcm-mk2-lower-receiver.trigger_pin_y":-0.689,"bcm-mk2-lower-receiver.well_roll_bottom_y":-0.202,"bcm-mk2-lower-receiver.well_roll_crest_out":0.8,"bcm-mk2-lower-receiver.well_roll_front_x":6.181,"bcm-mk2-lower-receiver.well_roll_rear_round":0.1,"bcm-mk2-lower-receiver.well_roll_rear_x":2.78,"bcm-mk2-lower-receiver.window_front_x":2.947,"bcm-mk2-lower-receiver.window_rear_x":1.68,"std.ar15.bolt_catch_boss_out":0.618,"std.ar15.bolt_catch_plunger_hole_d":0.156,"std.ar15.bolt_catch_plunger_hole_depth":0.4703,"std.ar15.bolt_catch_plunger_hole_y":-0.195,"std.ar15.bolt_catch_slot_bottom_y":-0.38,"std.ar15.bolt_catch_slot_floor":0.4409,"std.ar15.bolt_catch_slot_front_x":3.375,"std.ar15.bolt_catch_slot_width":0.172,"std.ar15.bore_axis_y":0.8775,"std.ar15.buffer_tower_front_x":-0.628,"std.ar15.buffer_tower_od":1.392,"std.ar15.deck_front_x":6.194,"std.ar15.deck_y":0.2485,"std.ar15.fcg_pin_hole_d":0.15675,"std.ar15.fcg_pocket_corner_r":0.218,"std.ar15.fcg_pocket_depth":1.249,"std.ar15.fcg_pocket_front_x":3.11,"std.ar15.fcg_pocket_length":2.87,"std.ar15.fcg_pocket_width":0.69,"std.ar15.front_lug_slot_width":0.5,"std.ar15.grip_lug_depth":0.93,"std.ar15.grip_lug_face_angle":60,"std.ar15.grip_lug_face_from_pin":1.228,"std.ar15.grip_lug_front_from_rear_face":2.3,"std.ar15.grip_lug_length":1.25,"std.ar15.grip_lug_width":0.375,"std.ar15.grip_seat_below_deck":1.318,"std.ar15.lower_body_width":0.88,"std.ar15.mag_catch_boss_edge_r":0.059,"std.ar15.mag_catch_boss_proud":0.0906,"std.ar15.mag_catch_boss_r":0.253,"std.ar15.mag_catch_boss_x":4.262,"std.ar15.mag_catch_cbore_d":0.312,"std.ar15.mag_catch_cbore_depth":0.25,"std.ar15.mag_catch_fence_out":0.549,"std.ar15.mag_catch_hole_d":0.2055,"std.ar15.mag_catch_slot_bottom_y":-0.689,"std.ar15.mag_catch_slot_floor":0.3799,"std.ar15.mag_catch_slot_front_x":4.557,"std.ar15.mag_catch_slot_h":0.252,"std.ar15.mag_catch_slot_rear_x":3.048,"std.ar15.mag_catch_x":3.291,"std.ar15.mag_catch_y":-0.565,"std.ar15.mag_release_pocket_depth":0.617,"std.ar15.mag_release_pocket_h":0.515,"std.ar15.mag_release_pocket_w":0.319,"std.ar15.magwell_band_bottom_y":-1.959,"std.ar15.magwell_band_front_x":4.549,"std.ar15.magwell_band_proud":0.059,"std.ar15.magwell_band_rear_x":3.975,"std.ar15.magwell_band_side":0.084,"std.ar15.magwell_box_length":2.398,"std.ar15.magwell_corner_r":0.062,"std.ar15.magwell_front_inner_x":6.025,"std.ar15.magwell_length":2.553,"std.ar15.magwell_outside_width":1.098,"std.ar15.magwell_spine_slot_width":0.47,"std.ar15.magwell_width":0.898,"std.ar15.pin_spacing":6.375,"std.ar15.pivot_hole_d":0.251,"std.ar15.rear_lug_slot_depth":0.63,"std.ar15.rear_lug_slot_rear_x":-0.402,"std.ar15.rear_lug_slot_width":0.5,"std.ar15.rear_underside_arc_center_below_seat":0.1928,"std.ar15.rear_underside_arc_center_x":-1.0238,"std.ar15.rear_underside_arc_r":0.75,"std.ar15.rear_underside_round_r":0.44,"std.ar15.rear_wall_arc_r":0.75,"std.ar15.receiver_rear_x":-1.125,"std.ar15.safety_detent_boss_below_deck":0.455,"std.ar15.safety_detent_boss_face":0.53,"std.ar15.safety_detent_boss_from_rear":0.36,"std.ar15.safety_detent_boss_length":0.43,"std.ar15.selector_hole_d":0.376,"std.ar15.takedown_hole_d":0.251,"std.ar15.takedown_spotface_d":0.44,"std.ar15.takedown_spotface_depth":0.04,"std.ar15.trigger_guard_ear_gap":0.442,"std.ar15.trigger_guard_ears_width":0.659,"std.ar15.trigger_guard_front_hole_d":0.1265,"std.ar15.trigger_guard_front_spotface_d":0.25,"std.ar15.trigger_guard_front_spotface_floor":0.3219,"std.ar15.trigger_guard_rear_hole_d":0.1285,"std.ar15.trigger_pin_x":1.928,"std.ar15.trigger_slot_front_ahead_of_pin":0.52,"std.ar15.trigger_slot_length":0.68,"std.ar15.trigger_slot_width":0.312,"std.ar15.upper_rear_face_x":-0.621,"std.receiver_extension.milspec_od":1.148},"profiles":{"side":[[-0.964,1.504],[-0.935,-0.267],[1.155,-0.892],[1.173,-0.911],[1.18,-1.071],[3.393,-1.039],[3.412,-1.057],[3.434,-2.298],[3.613,-2.281],[6.178,-1.818],[6.197,-1.799],[6.196,-1.732],[6.128,-1.666],[6.089,-1.577],[6.083,-0.645],[6.097,-0.563],[6.169,-0.398],[6.242,-0.315],[6.356,-0.22],[6.542,-0.143],[6.597,-0.086],[6.626,-0.019],[6.609,0.108],[6.537,0.193],[6.365,0.235],[6.223,0.233],[6.148,0.261],[3.561,0.239],[3.539,0.261],[2.331,0.228],[2.308,0.25],[1.742,0.227],[1.667,0.241],[0.169,0.219],[-0.018,0.239],[-0.182,0.296],[-0.295,0.361],[-0.42,0.475],[-0.504,0.586],[-0.565,0.712],[-0.543,1.249],[-0.581,1.278],[-0.581,1.323],[-0.604,1.352],[-0.606,1.501],[-0.707,1.511]],"complete":[[-0.964,1.504],[-0.938,-0.263],[1.155,-0.892],[1.196,-2.461],[1.482,-2.401],[1.541,-2.333],[1.923,-2.432],[2.236,-2.472],[2.534,-2.453],[3.345,-2.292],[3.613,-2.281],[6.178,-1.818],[6.196,-1.732],[6.089,-1.577],[6.097,-0.563],[6.169,-0.398],[6.242,-0.315],[6.356,-0.22],[6.542,-0.143],[6.626,-0.019],[6.609,0.108],[6.537,0.193],[6.148,0.261],[3.561,0.239],[3.433,0.349],[3.279,0.417],[3.254,0.566],[3.153,0.643],[3.041,0.634],[2.949,0.562],[2.914,0.39],[2.946,0.271],[2.927,0.237],[-0.018,0.239],[-0.295,0.361],[-0.504,0.586],[-0.565,0.712],[-0.543,1.249],[-0.604,1.352],[-0.606,1.501],[-0.707,1.511]]},"features":{"side":{},"complete":{"opening":[[[1.386,-1.713],[1.42,-1.459],[1.522,-1.286],[1.74,-1.13],[1.754,-1.078],[2.074,-1.073],[2.114,-1.221],[2.268,-1.085],[2.827,-1.084],[2.962,-1.127],[3.06,-1.2],[3.223,-1.395],[3.27,-1.521],[3.281,-1.737],[3.201,-1.932],[2.888,-2.194],[2.421,-2.328],[1.965,-2.297],[1.612,-2.086],[1.457,-1.936]]]}},"placement":{"side":{"plane":"xy","offset":{}},"complete":{"plane":"xy","offset":{}}},"bounds":{"min":[-1.125,-2.333,-0.6986],"max":[6.568,1.5735,0.8]},"volume_in3":5.2239,"centroid":[2.4153,-0.6227,0.0324],"shell":[2.8582,-0.6506,0.0102],"area_in2":76.722,"triangles":25574,"manifold":true,"interior":{"pocket":{"x":[0.24,3.11],"z":0.345,"floor_y":-1.0005},"rear_lug_slot":{"x":[-0.402,0.458],"z":0.25,"floor_y":-0.3815},"safety_detent_boss":{"x":[0.6,1.03],"face_z":0.185,"top_y":-0.2065},"trigger_slot":{"x":[1.768,2.448],"z":0.156},"magazine_well":{"x":[3.472,6.025],"z":0.449}},"holes":{"takedown":{"x":0,"y":0,"d":0.251},"pivot":{"x":6.375,"y":0,"d":0.251},"selector":{"x":0.803,"y":-0.466,"d":0.376},"hammer":{"x":2.771,"y":-0.375,"d":0.1568},"trigger":{"x":1.928,"y":-0.689,"d":0.1568},"guard rear":{"x":1.4985,"y":-2.18,"d":0.1285},"guard front":{"x":3.3425,"y":-2.18,"d":0.1265}},"catches":{"button_pocket":{"x":3.291,"y":-0.565,"floor_z":-0.068,"face_z":0.549},"catch_slot":{"x":[3.048,4.557],"floor_z":-0.3799},"bolt_catch_slot":{"x":[3.203,3.375],"bottom_y":-0.38,"floor_z":-0.4409}},"grip_mount":{"lug":{"seat_y":-1.0695,"x":[-0.075,1.175],"width":0.375,"foot_x":1.0072,"flat_y":-1.9995},"ears":{"width":0.659,"gap":0.442,"gap_top_y":-1.9995,"rear_x":[1.175,1.68],"front_x":[2.947,3.435],"rear_bottom_y":-2.333,"front_bottom_y":-2.288},"rear_underside":{"round_r":0.44,"arc_r":0.75,"axis_x":-1.0238,"axis_y":-1.2623}},"rear_walls":{"r":0.75,"centre":[0.122,0.9985],"x":[-0.621,0.122],"meets_face_y":0.8963,"runs_out":[0.055,0.2515],"toe_x":[-0.1255,0.055]},"deck":{"y":0.2485,"x":[-0.02,6.194]},"slabs":[[-1.125,-0.567,-0.696,-0.74,1.573,0.696],[-0.74,-0.919,-0.696,-0.356,1.573,0.696],[-0.356,-1.435,-0.44,0.029,0.416,0.44],[0.029,-1.657,-0.44,0.414,0.254,0.44],[0.414,-1.879,-0.44,0.798,0.249,0.44],[0.798,-2.333,-0.44,1.952,0.249,0.44],[1.952,-1.069,-0.44,2.721,0.249,0.44],[2.721,-2.298,-0.618,3.875,0.249,0.8],[3.875,-2.234,-0.699,4.26,0.249,0.8],[4.26,-2.164,-0.699,4.645,0.249,0.8],[4.645,-2.095,-0.549,5.029,0.249,0.8],[5.029,-2.025,-0.549,5.414,0.249,0.8],[5.414,-1.956,-0.549,5.799,0.249,0.8],[5.799,-1.886,-0.549,6.183,0.249,0.8],[6.183,-1.813,-0.549,6.568,0.249,0.549]],"slots":["receiver"]},"bcm-mk2-lower-receiver.selector":{"part":"bcm-mk2-lower-receiver","component":"selector","model":"bcm-mk2-lower-receiver.selector.glb","script":"brought_selectors.py","inputs":{"cmmg-safety-selector.hub_d":0.48,"cmmg-safety-selector.hub_t":0.05,"cmmg-safety-selector.lever_reach":0.81,"cmmg-safety-selector.lever_standoff":0.25,"cmmg-safety-selector.paddle_base_t":0.125,"cmmg-safety-selector.paddle_relief":0.015,"cmmg-safety-selector.paddle_relief_start":0.281,"cmmg-safety-selector.paddle_start":0.09,"cmmg-safety-selector.paddle_width":0.25,"cmmg-safety-selector.pointer_angle":60,"cmmg-safety-selector.pointer_fillet_r":0.09,"cmmg-safety-selector.pointer_reach":0.34,"cmmg-safety-selector.shaft_d":0.37225,"cmmg-safety-selector.shaft_end_chamfer":0.024,"cmmg-safety-selector.shaft_length":0.9375,"cmmg-safety-selector.step_1_height":0.17,"cmmg-safety-selector.step_1_inset":0.009,"cmmg-safety-selector.step_2_height":0.2,"cmmg-safety-selector.step_2_inset":0.025,"cmmg-safety-selector.step_3_height":0.22,"cmmg-safety-selector.step_3_inset":0.043,"cmmg-safety-selector.step_4_height":0.24,"cmmg-safety-selector.step_4_inset":0.075,"cmmg-safety-selector.step_5_inset":0.11,"std.ar15.lower_body_width":0.88,"std.ar15.selector_hole_d":0.376,"std.ar15.selector_x":0.803,"std.ar15.selector_y":-0.466},"profiles":{},"bounds":{"min":[-0.007,-0.7058,-0.69],"max":[1.143,-0.2262,0.4975]},"volume_in3":0.1423,"centroid":[0.703,-0.466,-0.1335],"shell":[0.665,-0.466,-0.2048],"area_in2":2.158,"triangles":6464,"manifold":true,"slabs":[[-0.007,-0.706,-0.69,1.143,-0.226,-0.294],[0.617,-0.652,-0.294,0.989,-0.28,0.498]],"slots":["controls"]},"bcm-mk2-receiver-extension":{"part":"bcm-mk2-receiver-extension","model":"bcm-mk2-receiver-extension.glb","script":"bcm_mk2_receiver_extension.py","inputs":{"bcm-mk2-receiver-extension.channel_depth":0.04,"bcm-mk2-receiver-extension.channel_width":0.343,"bcm-mk2-receiver-extension.front_slot_end_from_face":3.13,"bcm-mk2-receiver-extension.position_hole_d":0.326,"bcm-mk2-receiver-extension.position_hole_front_from_face":3.506,"bcm-mk2-receiver-extension.position_pitch_front":0.605,"bcm-mk2-receiver-extension.position_pitch_rear":0.531,"bcm-mk2-receiver-extension.rail_ramp_end":2.9,"bcm-mk2-receiver-extension.rail_ramp_start":2.35,"bcm-mk2-receiver-extension.rail_rear_chamfer":0.28,"bcm-mk2-receiver-extension.rear_notch_depth":0.26,"bcm-mk2-receiver-extension.rear_wall":0.072,"bcm-mk2-receiver-extension.relief_d":1.12,"bcm-mk2-receiver-extension.relief_length":0.144,"bcm-mk2-receiver-extension.thread_length":1.295,"bcm-mk2-receiver-extension.tube_front_behind_pin":0.669,"bcm-mk2-receiver-extension.tube_length":7.955,"bcm-mk2-receiver-extension.tube_od":1.148,"bcm-mk2-receiver-extension.vent_d":0.094,"std.receiver_extension.bore_d":1,"std.receiver_extension.key_slot_floor":0.55,"std.receiver_extension.key_slot_length":1.24,"std.receiver_extension.key_slot_width":0.125,"std.receiver_extension.rail_bottom_below_axis":0.874,"std.receiver_extension.rail_width":0.49,"std.receiver_extension.thread_major_d":1.1813,"std.receiver_extension.thread_minor_d":1.1093,"std.receiver_extension.thread_pitch":0.0625},"profiles":{},"bounds":{"min":[0.669,-0.874,-0.5907],"max":[8.624,0.5907,0.5907]},"volume_in3":2.5501,"centroid":[5.0237,-0.1442,-0.0001],"shell":[4.7449,-0.0811,-0.0001],"area_in2":64.4499,"triangles":35518,"manifold":true,"slabs":[[0.669,-0.592,-0.591,3.055,0.591,0.591],[3.055,-0.81,-0.574,3.453,0.574,0.574],[3.453,-0.874,-0.574,8.624,0.574,0.574]],"slots":["tube"]},"bcm-pmcr-carbine":{"part":"bcm-pmcr-carbine","model":"bcm-pmcr-carbine.glb","script":"bcm_pmcr_carbine.py","inputs":{"bcm-front-sight-base-f-750.port_from_rear":0.27,"bcm-handguard-cap-round-750.sheet":0.032,"bcm-pmcr-carbine.base_clearance":0.02,"bcm-pmcr-carbine.body_rear_x":0.2,"bcm-pmcr-carbine.bottom_below_axis":0.899,"bcm-pmcr-carbine.bottom_half_width":0.3,"bcm-pmcr-carbine.front_flange_od":1.36,"bcm-pmcr-carbine.front_notch_half_width":0.475,"bcm-pmcr-carbine.front_notch_x":6.795,"bcm-pmcr-carbine.front_wall_x":6,"bcm-pmcr-carbine.heat_shield_thickness":0.03,"bcm-pmcr-carbine.lower_width":1.745,"bcm-pmcr-carbine.mlok_bottom_face_distance":0.899,"bcm-pmcr-carbine.mlok_bottom_slot0_x":1.77,"bcm-pmcr-carbine.mlok_bottom_slots":3,"bcm-pmcr-carbine.mlok_side_face_angle":43,"bcm-pmcr-carbine.mlok_side_face_distance":0.998,"bcm-pmcr-carbine.mlok_side_slot0_x":2.343,"bcm-pmcr-carbine.mlok_side_slots":3,"bcm-pmcr-carbine.mounting_length":6.5,"bcm-pmcr-carbine.panel_bottom_y":-0.215,"bcm-pmcr-carbine.panel_depth":0.015,"bcm-pmcr-carbine.panel_divider1_bottom_x":4.16,"bcm-pmcr-carbine.panel_divider1_top_x":4.79,"bcm-pmcr-carbine.panel_divider2_bottom_x":6.39,"bcm-pmcr-carbine.panel_divider2_top_x":6.53,"bcm-pmcr-carbine.panel_divider_bottom_x":1.92,"bcm-pmcr-carbine.panel_divider_top_x":3.08,"bcm-pmcr-carbine.panel_dividers":3,"bcm-pmcr-carbine.panel_rear_x":0.31,"bcm-pmcr-carbine.panel_rib":0.11,"bcm-pmcr-carbine.panel_top_y":0.49,"bcm-pmcr-carbine.rear_collar_gap":0.436,"bcm-pmcr-carbine.rear_collar_gap_y":-0.091,"bcm-pmcr-carbine.rear_collar_od":1.621,"bcm-pmcr-carbine.seam_y":-0.339,"bcm-pmcr-carbine.spine_centre_rib":0.254,"bcm-pmcr-carbine.spine_groove0_x":0.147,"bcm-pmcr-carbine.spine_groove_count":14,"bcm-pmcr-carbine.spine_groove_pitch":0.499,"bcm-pmcr-carbine.spine_half_width":0.294,"bcm-pmcr-carbine.spine_pocket_rib":0.15,"bcm-pmcr-carbine.spine_rim":0.04,"bcm-pmcr-carbine.spine_slit_width":0.028,"bcm-pmcr-carbine.spine_vent0_x":0.874,"bcm-pmcr-carbine.spine_vent_count":6,"bcm-pmcr-carbine.spine_vent_height":0.1,"bcm-pmcr-carbine.spine_vent_length":0.395,"bcm-pmcr-carbine.spine_vent_pitch":1.016,"bcm-pmcr-carbine.spine_vent_y":1.1,"bcm-pmcr-carbine.tab_front_x":1.138,"bcm-pmcr-carbine.tab_knee_x":0.755,"bcm-pmcr-carbine.tab_proud":0.03,"bcm-pmcr-carbine.tab_top_y":-0.027,"bcm-pmcr-carbine.tab_x":0.153,"bcm-pmcr-carbine.top_above_axis":1.294,"bcm-pmcr-carbine.vent0_x":1.4,"bcm-pmcr-carbine.vent_count":5,"bcm-pmcr-carbine.vent_length":0.607,"bcm-pmcr-carbine.vent_pitch":1.022,"bcm-pmcr-carbine.vent_width":0.14,"bcm-pmcr-carbine.vent_y":-0.811,"bcm-pmcr-carbine.vent_z":0.451,"bcm-pmcr-carbine.wall":0.1,"bcm-pmcr-carbine.width":1.854,"std.ar15.slip_ring_notch_width":0.203,"std.mlok.slot_corner_r":0.0937007874015748,"std.mlok.slot_length":1.2598425196850394,"std.mlok.slot_pitch":1.574803149606299,"std.mlok.slot_width":0.2755905511811024},"profiles":{"side":[[0,-0.244],[0.026,-0.265],[0.191,-0.312],[0.218,-0.38],[0.212,-0.456],[0.091,-0.494],[0.065,-0.533],[0.029,-1.045],[0.165,-1.186],[0.177,-1.539],[0.2,-1.557],[0.185,-1.601],[0.091,-1.601],[0.071,-1.615],[0.077,-1.78],[0.112,-2.01],[0.141,-2.098],[0.168,-2.125],[0.25,-2.136],[0.282,-2.204],[0.321,-2.225],[3.775,-2.189],[5.947,-2.201],[6.141,-2.23],[6.259,-2.266],[6.28,-2.286],[6.315,-2.581],[6.356,-2.681],[6.418,-2.731],[6.518,-2.737],[6.591,-2.687],[6.668,-2.486],[6.756,-2.328],[7.021,-1.998],[7.156,-1.786],[7.162,-1.757],[7.139,-1.733],[7.262,-1.563],[7.28,-1.404],[7.274,-1.056],[7.256,-0.897],[7.209,-0.815],[6.827,-0.303],[6.792,-0.068],[6.759,-0.029],[6.73,-0.024],[6.694,-0.035],[6.636,-0.024],[6.259,-0.024],[6.247,-0.035],[6.165,-0.035],[6.135,-0.024],[5.77,-0.024],[5.717,-0.041],[5.241,-0.029],[5.164,-0.047],[5.135,-0.029],[4.958,-0.024],[4.758,-0.024],[4.682,-0.041],[4.67,-0.029],[4.234,-0.029],[4.176,-0.041],[4.105,-0.024],[3.734,-0.024],[3.705,-0.041],[3.652,-0.029],[3.64,-0.041],[3.599,-0.024],[3.234,-0.024],[3.193,-0.041],[3.104,-0.024],[2.634,-0.035],[2.604,-0.024],[2.233,-0.018],[2.175,-0.035],[2.092,-0.018],[1.833,-0.012],[1.598,-0.024],[1.121,-0.012],[1.103,-0.024],[1.009,-0.006],[0.032,0],[0.012,-0.044]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"y":"top_above_axis"}}},"bounds":{"min":[0,-1.443,-0.957],"max":[7.28,1.294,0.957]},"volume_in3":5.2782,"centroid":[3.7097,0.0759,0],"shell":[3.6017,-0.0009,0],"area_in2":121.7093,"triangles":28242,"manifold":true,"slabs":[[0,-0.934,-0.957,6.131,1.294,0.957],[6.131,-1.443,-0.928,6.897,1.294,0.928],[6.897,-0.859,-0.928,7.28,0.897,0.928]],"slots":["body","heat_shield"]},"bcm-pmcr-mid":{"part":"bcm-pmcr-mid","model":"bcm-pmcr-mid.glb","script":"bcm_pmcr_mid.py","inputs":{"bcm-front-sight-base-f-750.port_from_rear":0.27,"bcm-handguard-cap-triangle-750.collar":0.058,"bcm-handguard-cap-triangle-750.sheet":0.025,"bcm-pmcr-mid.base_clearance":0.02,"bcm-pmcr-mid.body_rear_x":0.193,"bcm-pmcr-mid.bottom_below_axis":0.922,"bcm-pmcr-mid.bottom_half_width":0.3,"bcm-pmcr-mid.front_flange_od":1.36,"bcm-pmcr-mid.front_notch_half_width":0.48,"bcm-pmcr-mid.front_notch_x":8.863,"bcm-pmcr-mid.front_wall_x":7.95,"bcm-pmcr-mid.heat_shield_thickness":0.03,"bcm-pmcr-mid.lower_width":1.717,"bcm-pmcr-mid.mlok_bottom_face_distance":0.922,"bcm-pmcr-mid.mlok_bottom_slot0_x":2.15,"bcm-pmcr-mid.mlok_bottom_slots":4,"bcm-pmcr-mid.mlok_side_face_angle":42,"bcm-pmcr-mid.mlok_side_face_distance":0.993,"bcm-pmcr-mid.mlok_side_slot0_x":2.78,"bcm-pmcr-mid.mlok_side_slots":4,"bcm-pmcr-mid.mounting_length":8.45,"bcm-pmcr-mid.panel_bottom_y":-0.13,"bcm-pmcr-mid.panel_depth":0.015,"bcm-pmcr-mid.panel_divider1_bottom_x":6.21,"bcm-pmcr-mid.panel_divider1_top_x":6.81,"bcm-pmcr-mid.panel_divider2_bottom_x":8.42,"bcm-pmcr-mid.panel_divider2_top_x":8.38,"bcm-pmcr-mid.panel_divider_bottom_x":3.94,"bcm-pmcr-mid.panel_divider_top_x":5.09,"bcm-pmcr-mid.panel_dividers":3,"bcm-pmcr-mid.panel_rear_x":0.5,"bcm-pmcr-mid.panel_rib":0.11,"bcm-pmcr-mid.panel_top_y":0.47,"bcm-pmcr-mid.rear_collar_gap":0.414,"bcm-pmcr-mid.rear_collar_gap_y":-0.108,"bcm-pmcr-mid.rear_collar_od":1.6,"bcm-pmcr-mid.seam_y":-0.378,"bcm-pmcr-mid.spine_centre_rib":0.267,"bcm-pmcr-mid.spine_groove0_x":0.146,"bcm-pmcr-mid.spine_groove_count":18,"bcm-pmcr-mid.spine_groove_pitch":0.5025,"bcm-pmcr-mid.spine_half_width":0.272,"bcm-pmcr-mid.spine_pocket_rib":0.15,"bcm-pmcr-mid.spine_rim":0.04,"bcm-pmcr-mid.spine_slit_width":0.03,"bcm-pmcr-mid.spine_vent0_x":0.858,"bcm-pmcr-mid.spine_vent_count":8,"bcm-pmcr-mid.spine_vent_height":0.103,"bcm-pmcr-mid.spine_vent_length":0.4,"bcm-pmcr-mid.spine_vent_pitch":1.014,"bcm-pmcr-mid.spine_vent_y":1.084,"bcm-pmcr-mid.tab_front_x":1.06,"bcm-pmcr-mid.tab_knee_x":0.695,"bcm-pmcr-mid.tab_proud":0.03,"bcm-pmcr-mid.tab_top_y":0.005,"bcm-pmcr-mid.tab_x":0.133,"bcm-pmcr-mid.top_above_axis":1.259,"bcm-pmcr-mid.vent0_x":1.376,"bcm-pmcr-mid.vent_count":7,"bcm-pmcr-mid.vent_length":0.607,"bcm-pmcr-mid.vent_pitch":1.0175,"bcm-pmcr-mid.vent_width":0.12,"bcm-pmcr-mid.vent_y":-0.843,"bcm-pmcr-mid.vent_z":0.418,"bcm-pmcr-mid.wall":0.1,"bcm-pmcr-mid.width":1.873,"std.ar15.slip_ring_notch_width":0.203,"std.mlok.slot_corner_r":0.0937007874015748,"std.mlok.slot_length":1.2598425196850394,"std.mlok.slot_pitch":1.574803149606299,"std.mlok.slot_width":0.2755905511811024},"profiles":{"side":[[0,-0.233],[0.012,-0.259],[0.185,-0.315],[0.205,-0.359],[0.191,-0.462],[0.084,-0.495],[0.058,-0.52],[0.018,-0.763],[0,-1.046],[0.13,-1.186],[0.153,-1.541],[0.145,-1.587],[0.055,-1.589],[0.034,-1.611],[0.047,-1.766],[0.092,-1.986],[0.133,-2.085],[0.163,-2.113],[0.235,-2.122],[0.265,-2.188],[0.311,-2.212],[2.926,-2.181],[7.926,-2.201],[8.114,-2.226],[8.283,-2.275],[8.311,-2.308],[8.34,-2.593],[8.365,-2.665],[8.416,-2.727],[8.479,-2.74],[8.544,-2.736],[8.606,-2.683],[8.673,-2.478],[8.734,-2.362],[9.145,-1.788],[9.156,-1.757],[9.132,-1.741],[9.253,-1.577],[9.28,-1.444],[9.271,-0.957],[9.258,-0.896],[8.839,-0.289],[8.81,-0.075],[8.797,-0.037],[8.769,-0.013],[8.683,-0.027],[8.674,-0.016],[8.265,-0.018],[8.24,-0.034],[8.132,-0.016],[7.768,-0.018],[7.716,-0.038],[7.638,-0.02],[7.258,-0.02],[7.238,-0.038],[7.132,-0.02],[6.752,-0.018],[6.68,-0.038],[6.615,-0.02],[6.3,-0.02],[6.233,-0.022],[6.224,-0.043],[6.201,-0.029],[6.129,-0.036],[6.12,-0.02],[5.738,-0.02],[5.673,-0.038],[5.574,-0.02],[5.228,-0.022],[5.183,-0.036],[5.129,-0.027],[5.12,-0.04],[5.111,-0.02],[4.74,-0.02],[4.648,-0.036],[4.612,-0.022],[4.266,-0.02],[4.124,-0.029],[4.113,-0.045],[4.111,-0.02],[4.079,-0.018],[3.724,-0.018],[3.65,-0.036],[3.589,-0.018],[3.216,-0.018],[3.151,-0.031],[3.092,-0.016],[2.897,-0.013],[2.703,-0.013],[2.665,-0.027],[2.546,-0.013],[2.168,-0.013],[2.148,-0.027],[2.094,-0.011],[1.719,-0.009],[1.633,-0.025],[1.597,-0.011],[1.588,-0.025],[1.577,-0.011],[1.154,-0.011],[1.118,-0.022],[1.067,-0.007],[0.667,-0.004],[0.658,-0.018],[0.592,-0.02],[0.568,-0.002],[0.41,0],[0.132,-0.013],[0.046,-0.004],[0.016,-0.053]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"y":"top_above_axis"}}},"bounds":{"min":[0,-1.481,-0.9665],"max":[9.28,1.259,0.9665]},"volume_in3":6.9551,"centroid":[4.7013,0.0613,0],"shell":[4.5911,-0.0236,0],"area_in2":151.2664,"triangles":32440,"manifold":true,"slabs":[[0,-0.925,-0.966,8.12,1.259,0.966],[8.12,-1.481,-0.937,8.893,1.259,0.937],[8.893,-0.88,-0.937,9.28,0.891,0.937]],"slots":["body","heat_shield"]},"bcm-pnt-trigger":{"part":"bcm-pnt-trigger","model":"bcm-pnt-trigger.glb","script":"bcm_pnt_trigger.py","inputs":{"bcm-pnt-trigger.blade_back_depth":0.107,"bcm-pnt-trigger.blade_face_r":0.375,"bcm-pnt-trigger.blade_section_length":0.194,"bcm-pnt-trigger.block_bottom_below_pivot":0.378,"bcm-pnt-trigger.block_front_ahead_of_pivot":0.5,"bcm-pnt-trigger.boss_fillet_r":0.055,"bcm-pnt-trigger.boss_length":0.68,"bcm-pnt-trigger.boss_step_above_axis":0.03,"bcm-pnt-trigger.boss_step_length":0.058,"bcm-pnt-trigger.edge_r":0.031,"bcm-pnt-trigger.pivot_hole_d":0.1565,"bcm-pnt-trigger.rest_angle":-1,"bcm-pnt-trigger.slot_floor_below_pivot":0.19,"bcm-pnt-trigger.slot_front_ahead_of_pivot":0.48,"bcm-pnt-trigger.slot_front_r":1,"bcm-pnt-trigger.slot_width":0.1255,"bcm-pnt-trigger.spring_hole_behind_pivot":0.614,"bcm-pnt-trigger.spring_hole_d":0.164,"bcm-pnt-trigger.spring_hole_floor_below_pivot":0.23,"bcm-pnt-trigger.tail_step_depth":0.013,"bcm-pnt-trigger.tail_step_length":0.375,"bcm-pnt-trigger.web_from_below_pivot":0.75,"std.ar15.trigger_body_width":0.29,"std.ar15.trigger_boss_d":0.3145,"std.ar15.trigger_tail_behind_pivot":1.2025},"profiles":{"side":[[-1.208,-0.211],[-1.199,-0.239],[-1.191,-0.244],[-0.363,-0.259],[-0.109,-0.269],[-0.095,-0.284],[-0.097,-0.37],[-0.059,-0.402],[-0.053,-0.415],[-0.054,-0.456],[-0.077,-0.494],[-0.077,-0.506],[-0.09,-0.522],[-0.09,-0.538],[-0.1,-0.55],[-0.104,-0.576],[-0.113,-0.591],[-0.117,-0.626],[-0.127,-0.636],[-0.138,-0.699],[-0.141,-0.883],[-0.135,-0.899],[-0.13,-0.978],[-0.124,-0.985],[-0.097,-1.093],[-0.069,-1.151],[-0.066,-1.17],[-0.033,-1.231],[-0.017,-1.247],[-0.017,-1.272],[-0.006,-1.274],[0.008,-1.288],[0.063,-1.362],[0.127,-1.425],[0.146,-1.435],[0.178,-1.436],[0.199,-1.419],[0.2,-1.381],[0.144,-1.313],[0.104,-1.239],[0.098,-1.204],[0.082,-1.188],[0.07,-1.153],[0.05,-1.054],[0.051,-0.962],[0.045,-0.946],[0.052,-0.931],[0.053,-0.877],[0.067,-0.823],[0.076,-0.814],[0.09,-0.738],[0.1,-0.728],[0.1,-0.716],[0.116,-0.7],[0.123,-0.672],[0.175,-0.596],[0.238,-0.533],[0.322,-0.464],[0.37,-0.433],[0.44,-0.4],[0.487,-0.389],[0.49,-0.189],[0.494,-0.158],[0.512,-0.141],[0.767,-0.147],[0.789,0.031],[0.759,0.036],[0.293,0.044],[0.288,0.03],[0.263,0.007],[0.2,0.001],[0.178,0.008],[0.164,0.023],[0.13,0.096],[0.101,0.133],[0.088,0.133],[0.016,0.163],[-0.013,0.164],[-0.061,0.155],[-0.106,0.134],[-0.143,0.095],[-0.163,0.041],[-0.197,0.011],[-0.225,0.009],[-0.263,0.013],[-0.296,0.043],[-0.297,0.054],[-0.332,0.061],[-0.561,0.062],[-1.119,0.078],[-1.189,0.067],[-1.2,0.059]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{}}},"bounds":{"min":[-1.208,-1.4354,-0.34],"max":[0.789,0.164,0.34]},"volume_in3":0.2146,"centroid":[-0.0789,-0.2873,0],"shell":[-0.1774,-0.2462,0],"area_in2":4.8107,"triangles":16028,"manifold":true,"slabs":[[-1.208,-0.258,-0.145,-0.409,0.078,0.145],[-0.409,-1.267,-0.34,-0.01,0.164,0.34],[-0.01,-1.435,-0.34,0.39,0.164,0.34],[0.39,-0.424,-0.145,0.789,0.042,0.145]],"slots":["body"]},"bcm-qd-end-plate":{"part":"bcm-qd-end-plate","model":"bcm-qd-end-plate.glb","script":"bcm_qd_end_plate.py","inputs":{"bcm-qd-end-plate.socket_below_axis":0.979,"bcm-qd-end-plate.socket_bore_d":0.37,"bcm-qd-end-plate.socket_od":0.547,"bcm-qd-end-plate.socket_proud_front":0.1,"bcm-qd-end-plate.socket_proud_rear":0.12,"bcm-qd-end-plate.thickness":0.115,"bcm-qd-end-plate.top_above_axis":0.665,"std.receiver_extension.end_plate_hole_d":1.1902,"std.receiver_extension.key_slot_floor":0.55,"std.receiver_extension.key_slot_width":0.125,"std.receiver_extension.thread_major_d":1.1813},"profiles":{"face":[[-0.667,-0.696],[-0.636,-0.861],[-0.561,-1.037],[-0.417,-1.69],[-0.383,-1.784],[-0.312,-1.886],[-0.211,-1.967],[-0.084,-2.015],[0.023,-2.023],[0.138,-1.998],[0.232,-1.95],[0.325,-1.865],[0.379,-1.776],[0.561,-1.037],[0.648,-0.822],[0.667,-0.64],[0.648,-0.506],[0.617,-0.412],[0.544,-0.281],[0.461,-0.184],[0.359,-0.104],[0.23,-0.04],[0.1,-0.004],[0,0],[-0.044,0],[-0.167,-0.019],[-0.284,-0.061],[-0.415,-0.142],[-0.502,-0.224],[-0.575,-0.325],[-0.632,-0.446],[-0.663,-0.581]]},"features":{"face":{}},"placement":{"face":{"plane":"zy","offset":{"y":"top_above_axis"}}},"bounds":{"min":[-0.1,-1.358,-0.667],"max":[0.235,0.665,0.667]},"volume_in3":0.1179,"centroid":[0.0611,-0.6729,-0.0041],"shell":[0.0611,-0.5455,-0.0029],"area_in2":3.3521,"triangles":3932,"manifold":true,"slabs":[[-0.1,-1.358,-0.418,0.235,-1.021,0.401],[-0.1,-1.021,-0.492,0.235,-0.684,0.484],[0,-0.684,-0.572,0.115,-0.347,0.571],[0,-0.347,-0.667,0.115,0.328,0.667],[0,0.328,-0.581,0.115,0.665,0.575]],"slots":["plate"]},"bcm-receiver-extension":{"part":"bcm-receiver-extension","model":"bcm-receiver-extension.glb","script":"bcm_receiver_extension.py","inputs":{"bcm-receiver-extension.position_hole_d":0.42,"bcm-receiver-extension.position_hole_rear_from_rear":0.44,"bcm-receiver-extension.position_step":0.66,"bcm-receiver-extension.tube_front_behind_pin":0.669,"bcm-receiver-extension.tube_length":7.25,"bcm-receiver-extension.tube_od":1.148,"std.receiver_extension.bore_d":1,"std.receiver_extension.carbine_rear_wall":0.072,"std.receiver_extension.carbine_vent_d":0.094,"std.receiver_extension.key_slot_floor":0.55,"std.receiver_extension.key_slot_length":1.24,"std.receiver_extension.key_slot_width":0.125,"std.receiver_extension.rail_bottom_below_axis":0.874,"std.receiver_extension.rail_ramp_end":2.592,"std.receiver_extension.rail_ramp_start":2.326,"std.receiver_extension.rail_width":0.49,"std.receiver_extension.thread_length":1.181,"std.receiver_extension.thread_major_d":1.1813,"std.receiver_extension.thread_minor_d":1.1093,"std.receiver_extension.thread_pitch":0.0625},"profiles":{},"bounds":{"min":[0.669,-0.874,-0.5907],"max":[7.919,0.5907,0.5907]},"volume_in3":2.3555,"centroid":[4.6197,-0.1498,-0.0001],"shell":[4.4119,-0.0803,-0.0001],"area_in2":58.7549,"triangles":30260,"manifold":true,"slabs":[[0.669,-0.587,-0.591,2.958,0.591,0.591],[2.958,-0.874,-0.574,7.919,0.574,0.574]],"slots":["tube"]},"bcm-rifle-m16-action-spring":{"part":"bcm-rifle-m16-action-spring","model":"bcm-rifle-m16-action-spring.glb","script":"bcm_rifle_m16_action_spring.py","inputs":{"bcm-mk2-buffer-t0.collar_d":0.781,"bcm-mk2-buffer-t0.head_thickness":0.254,"bcm-rifle-m16-action-spring.assembled_length_rifle":8.19,"bcm-rifle-m16-action-spring.coils":43.5,"bcm-rifle-m16-action-spring.free_length":12.5,"bcm-rifle-m16-action-spring.installed_length":7.677,"bcm-rifle-m16-action-spring.od":0.94,"bcm-rifle-m16-action-spring.solid_length":3.285,"bcm-rifle-m16-action-spring.wire_d":0.072,"std.receiver_extension.bore_d":1},"profiles":{},"bounds":{"min":[0.254,-0.4719,-0.4719],"max":[7.931,0.4719,0.4719]},"volume_in3":0.4809,"centroid":[4.0925,0,0.0032],"shell":[4.0925,0,0.0032],"area_in2":27.4782,"triangles":19500,"manifold":true,"slabs":[[0.254,-0.472,-0.472,7.931,0.472,0.472]],"slots":["spring"]},"bcm-stock-mod-0":{"part":"bcm-stock-mod-0","model":"bcm-stock-mod-0.glb","script":"bcm_stock_mod_0.py","inputs":{"bcm-stock-mod-0.body_width":1.462,"bcm-stock-mod-0.butt_behind_tube_rear_pos1":0.768,"bcm-stock-mod-0.cheek_width":1.334,"bcm-stock-mod-0.length":6.657,"bcm-stock-mod-0.pad_rib_angle":36.5,"bcm-stock-mod-0.pad_rib_depth":0.0113,"bcm-stock-mod-0.pad_rib_pitch":0.115,"bcm-stock-mod-0.pad_rib_top":0.83,"bcm-stock-mod-0.qd_panel_recess_depth":0.05,"bcm-stock-mod-0.strut_rib_depth":0.0133,"bcm-stock-mod-0.strut_rib_pitch":0.0671,"bcm-stock-mod-0.triangle_recess_depth":0.1,"bcm-stock-mod-0.tube_axis_below_top":0.712,"bcm-stock-mod-0.width":1.67,"bcm-stock-mod-0.wing_end_below_top":1.65,"bcm-stock-mod-0.wing_top_below_top":0.649,"bcm-stock-mod-0.wing_widest_below_top":0.976,"std.receiver_extension.milspec_od":1.148,"std.receiver_extension.rail_bottom_below_axis":0.874,"std.receiver_extension.rail_width":0.49},"profiles":{"side":[[0,-0.421],[0.008,-0.637],[0.1,-1.472],[0.116,-1.508],[0.112,-1.607],[0.128,-1.659],[0.124,-1.739],[0.14,-1.791],[0.136,-1.871],[0.152,-1.923],[0.148,-2.003],[0.164,-2.055],[0.16,-2.139],[0.176,-2.19],[0.172,-2.274],[0.188,-2.326],[0.184,-2.41],[0.2,-2.458],[0.196,-2.542],[0.212,-2.59],[0.208,-2.678],[0.224,-2.722],[0.244,-3.049],[0.26,-3.093],[0.268,-3.281],[0.288,-3.341],[0.296,-3.524],[0.327,-3.684],[0.323,-3.748],[0.339,-3.788],[0.347,-3.948],[0.367,-4.003],[0.375,-4.155],[0.395,-4.203],[0.399,-4.275],[0.423,-4.319],[0.423,-4.367],[0.451,-4.411],[0.455,-4.499],[0.483,-4.515],[0.487,-4.571],[0.575,-4.822],[0.633,-4.876],[0.761,-4.88],[0.789,-4.9],[0.813,-4.888],[0.984,-4.888],[1.118,-4.778],[1.873,-3.652],[1.873,-3.632],[1.905,-3.604],[1.909,-3.576],[1.981,-3.492],[2.021,-3.408],[2.097,-3.317],[2.093,-3.301],[2.204,-3.157],[2.204,-3.133],[2.24,-3.105],[2.24,-3.077],[2.28,-3.041],[2.276,-3.005],[2.378,-2.895],[2.486,-2.927],[2.528,-2.961],[2.556,-3.017],[2.544,-3.125],[2.558,-3.147],[2.59,-3.151],[2.616,-3.133],[2.759,-2.777],[2.809,-2.712],[2.829,-2.763],[2.909,-2.763],[2.993,-2.756],[3.025,-2.736],[3.664,-2.68],[3.852,-2.676],[4.543,-2.608],[4.794,-2.604],[4.942,-2.576],[4.994,-2.588],[5.781,-2.52],[5.932,-2.468],[6.695,-2.109],[6.713,-2.083],[6.761,-1.779],[6.753,-1.747],[6.693,-1.711],[6.739,-1.685],[6.765,-1.643],[6.825,-0.617],[6.793,-0.337],[6.753,-0.154],[6.723,-0.104],[6.615,-0.068],[1.927,-0.064],[0.972,-0.076],[0.865,-0.072],[0.789,-0.004],[0.697,0],[0.373,-0.012],[0.206,-0.044],[0.154,-0.068],[0.088,-0.126],[0.036,-0.206],[0.008,-0.302]],"rear":[[-0.731,-0.731],[-0.731,-1.627],[-0.719,-3.187],[-0.673,-3.643],[-0.575,-4.146],[-0.43,-4.712],[-0.384,-4.799],[-0.3,-4.865],[-0.254,-4.883],[0.064,-4.9],[0.272,-4.877],[0.352,-4.831],[0.402,-4.776],[0.448,-4.649],[0.633,-3.869],[0.691,-3.505],[0.725,-3.042],[0.731,-1.673],[0.725,-0.65],[0.679,-0.459],[0.598,-0.303],[0.416,-0.121],[0.22,-0.029],[0,0],[-0.058,0],[-0.254,-0.04],[-0.439,-0.139],[-0.569,-0.263],[-0.673,-0.442],[-0.719,-0.598]]},"features":{"side":{"through":[[[1.43,-2.027],[1.454,-1.951],[1.5,-1.897],[1.571,-1.861],[1.619,-1.861],[1.695,-1.897],[1.745,-1.951],[1.769,-2.011],[1.769,-2.091],[1.745,-2.15],[1.695,-2.204],[1.643,-2.228],[1.575,-2.224],[1.504,-2.192],[1.458,-2.143],[1.434,-2.087]],[[0.847,-2.71],[0.859,-2.666],[0.897,-2.64],[2.234,-2.564],[2.302,-2.568],[2.336,-2.614],[2.314,-2.668],[2.238,-2.696],[0.917,-2.767],[0.873,-2.752]],[[3.818,-2.166],[3.868,-2.113],[3.928,-2.117],[3.954,-2.158],[3.954,-2.214],[3.848,-2.256],[3.822,-2.222]]],"buttpad":[[[-0.641,0.25],[0.294,0.25],[0.302,-0.03],[0.341,-0.589],[0.393,-1.188],[0.449,-1.787],[0.529,-2.386],[0.601,-2.985],[0.669,-3.584],[0.729,-4.183],[0.789,-4.782],[0.805,-5.162],[-0.641,-5.162]]],"wing":[[[0.341,-0.649],[2.334,-0.649],[2.422,-0.689],[2.462,-0.781],[2.482,-1.188],[2.522,-1.587],[2.562,-1.979],[2.194,-1.979],[2.083,-1.807],[1.895,-1.687],[1.595,-1.651],[1.296,-1.687],[1.108,-1.807],[0.976,-1.979],[0.477,-1.979],[0.449,-1.787],[0.393,-1.188],[0.349,-0.709]]],"qd_cup":[[[1.923,-2.039],[1.916,-2.103],[1.898,-2.164],[1.868,-2.221],[1.827,-2.27],[1.777,-2.311],[1.721,-2.341],[1.659,-2.36],[1.595,-2.366],[1.531,-2.36],[1.47,-2.341],[1.413,-2.311],[1.364,-2.27],[1.323,-2.221],[1.293,-2.164],[1.274,-2.103],[1.268,-2.039],[1.274,-1.975],[1.293,-1.913],[1.323,-1.857],[1.364,-1.807],[1.413,-1.766],[1.47,-1.736],[1.531,-1.718],[1.595,-1.711],[1.659,-1.718],[1.721,-1.736],[1.777,-1.766],[1.827,-1.807],[1.868,-1.857],[1.898,-1.913],[1.916,-1.975]]],"lever":[[[2.785,-2.75],[3.177,-1.855],[5.265,-1.855],[6.587,-1.699],[6.907,-1.699],[6.907,-2.865],[2.825,-2.865]]],"strut_ribs":[[[2.194,-3.009],[1.156,-4.431],[1.056,-4.363],[2.099,-2.937]]],"qd_panel":[[[0.657,-1.947],[1.108,-1.947],[1.204,-1.907],[1.276,-1.843],[1.388,-1.731],[1.492,-1.683],[1.595,-1.667],[1.699,-1.683],[1.803,-1.731],[1.915,-1.843],[1.987,-1.907],[2.043,-1.947],[2.498,-1.947],[2.518,-2.522],[0.657,-2.522]]],"triangle":[[[0.797,-2.965],[2.043,-2.913],[2.083,-2.937],[2.071,-2.985],[1.987,-3.105],[1.056,-4.583],[1.004,-4.654],[0.976,-4.646],[0.964,-4.602]]]},"rear":{}},"placement":{"side":{"plane":"xy","offset":{"y":"tube_axis_below_top"}},"rear":{"plane":"zy","offset":{"y":"tube_axis_below_top"}}},"bounds":{"min":[0,-4.188,-0.835],"max":[6.657,0.712,0.835]},"volume_in3":18.3251,"centroid":[2.6109,-1.2986,-0.0003],"shell":[2.7538,-1.0316,0.0002],"area_in2":127.8433,"triangles":44626,"manifold":true,"slabs":[[0,-3.568,-0.835,0.392,0.701,0.835],[0.392,-4.188,-0.835,1.175,0.712,0.835],[1.175,-3.937,-0.835,1.566,0.644,0.835],[1.566,-3.333,-0.835,1.958,0.648,0.835],[1.958,-2.725,-0.835,2.35,0.648,0.835],[2.35,-2.439,-0.835,2.741,0.648,0.835],[2.741,-2.051,-0.728,3.133,0.647,0.73],[3.133,-2.008,-0.667,3.916,0.647,0.667],[3.916,-1.948,-0.667,4.699,0.646,0.667],[4.699,-1.888,-0.667,5.482,0.646,0.667],[5.482,-1.822,-0.667,5.874,0.645,0.667],[5.874,-1.714,-0.667,6.265,0.645,0.667],[6.265,-1.525,-0.667,6.657,0.644,0.667]],"slots":["body","buttpad","qd"]},"bcm-vertical-grip-mod-3-mlok":{"part":"bcm-vertical-grip-mod-3-mlok","model":"bcm-vertical-grip-mod-3-mlok.glb","script":"bcm_vertical_grip_mod_3_mlok.py","inputs":{"bcm-vertical-grip-mod-3-mlok.base_cavity_depth":1.6,"bcm-vertical-grip-mod-3-mlok.body_width":0.92,"bcm-vertical-grip-mod-3-mlok.boss_d":0.46,"bcm-vertical-grip-mod-3-mlok.corner_r":0.1,"bcm-vertical-grip-mod-3-mlok.groove_depth":0.044,"bcm-vertical-grip-mod-3-mlok.groove_width":0.03,"bcm-vertical-grip-mod-3-mlok.lug_spacing":0.783,"bcm-vertical-grip-mod-3-mlok.lug_x":0.688,"bcm-vertical-grip-mod-3-mlok.panel_bottom":0.24,"bcm-vertical-grip-mod-3-mlok.panel_depth":0.02,"bcm-vertical-grip-mod-3-mlok.panel_inset":0.19,"bcm-vertical-grip-mod-3-mlok.panel_top":0.59,"bcm-vertical-grip-mod-3-mlok.plate_corner_r":0.25,"bcm-vertical-grip-mod-3-mlok.rake":5.45,"bcm-vertical-grip-mod-3-mlok.rib_width":0.06,"bcm-vertical-grip-mod-3-mlok.ridge_first_front":0.489,"bcm-vertical-grip-mod-3-mlok.ridge_first_rear":0.534,"bcm-vertical-grip-mod-3-mlok.ridge_pitch":0.06,"bcm-vertical-grip-mod-3-mlok.ridges_front":35,"bcm-vertical-grip-mod-3-mlok.ridges_rear":32,"bcm-vertical-grip-mod-3-mlok.top_cells_depth":0.35,"bcm-vertical-grip-mod-3-mlok.wall":0.09,"bcm-vertical-grip-mod-3-mlok.width":1.02},"profiles":{"side":[[0,0.112],[0.004,0.049],[0.023,0.024],[0.058,0.002],[0.149,0.013],[0.154,0.009],[0.415,0.012],[0.42,0.008],[0.473,0.011],[0.478,0.007],[0.782,0.013],[0.787,0.009],[0.859,0.014],[0.864,0.009],[0.951,0.015],[0.956,0.011],[1.154,0.014],[1.159,0.01],[1.236,0.015],[1.256,0.007],[1.482,0.013],[1.487,0.008],[1.709,0.014],[1.714,0.009],[1.719,0.014],[1.752,0.017],[1.757,0.012],[1.859,0.014],[1.864,0.01],[1.984,0.013],[2.072,0],[2.125,0.008],[2.143,0.019],[2.159,0.037],[2.166,0.076],[2.155,0.167],[2.126,0.233],[2.095,0.274],[2.013,0.341],[1.986,0.373],[1.959,0.424],[1.941,0.476],[1.963,0.497],[1.962,0.512],[1.922,0.533],[1.944,0.564],[1.943,0.578],[1.903,0.604],[1.925,0.63],[1.924,0.649],[1.889,0.671],[1.915,0.706],[1.907,0.723],[1.879,0.738],[1.89,0.755],[1.907,0.764],[1.905,0.783],[1.885,0.801],[1.902,0.826],[1.901,0.841],[1.876,0.863],[1.898,0.884],[1.897,0.903],[1.867,0.92],[1.894,0.946],[1.893,0.961],[1.868,0.978],[1.89,1.004],[1.884,1.023],[1.859,1.041],[1.881,1.061],[1.88,1.086],[1.859,1.099],[1.877,1.119],[1.876,1.143],[1.855,1.161],[1.873,1.182],[1.872,1.201],[1.846,1.218],[1.869,1.244],[1.868,1.259],[1.847,1.276],[1.865,1.302],[1.864,1.316],[1.838,1.339],[1.861,1.364],[1.86,1.374],[1.839,1.401],[1.852,1.417],[1.856,1.436],[1.83,1.459],[1.848,1.475],[1.847,1.499],[1.826,1.517],[1.844,1.537],[1.842,1.561],[1.827,1.579],[1.84,1.595],[1.838,1.619],[1.818,1.637],[1.836,1.657],[1.834,1.676],[1.814,1.694],[1.832,1.715],[1.831,1.734],[1.81,1.752],[1.828,1.777],[1.827,1.792],[1.806,1.815],[1.819,1.83],[1.823,1.845],[1.801,1.877],[1.819,1.902],[1.813,1.921],[1.798,1.935],[1.811,1.95],[1.809,1.979],[1.789,1.992],[1.807,2.013],[1.805,2.037],[1.789,2.055],[1.803,2.07],[1.801,2.094],[1.786,2.108],[1.799,2.128],[1.797,2.152],[1.777,2.17],[1.795,2.186],[1.793,2.215],[1.777,2.233],[1.791,2.248],[1.789,2.272],[1.773,2.29],[1.787,2.306],[1.785,2.33],[1.769,2.348],[1.782,2.368],[1.781,2.388],[1.765,2.406],[1.778,2.431],[1.777,2.45],[1.761,2.468],[1.774,2.489],[1.773,2.508],[1.752,2.526],[1.77,2.546],[1.769,2.565],[1.733,2.592],[1.726,2.693],[1.697,2.732],[1.683,2.731],[1.653,2.748],[1.599,2.759],[1.502,2.762],[1.497,2.767],[1.449,2.763],[1.444,2.768],[1.126,2.751],[1.097,2.744],[1.083,2.748],[1.078,2.743],[1.059,2.746],[1.03,2.739],[0.809,2.724],[0.799,2.733],[0.784,2.732],[0.775,2.722],[0.434,2.694],[0.43,2.689],[0.272,2.668],[0.172,2.642],[0.112,2.609],[0.088,2.576],[0.08,2.547],[0.092,2.441],[0.065,2.41],[0.066,2.391],[0.087,2.373],[0.074,2.353],[0.075,2.329],[0.096,2.311],[0.078,2.29],[0.079,2.281],[0.085,2.267],[0.105,2.254],[0.087,2.233],[0.088,2.214],[0.109,2.196],[0.096,2.176],[0.097,2.157],[0.118,2.134],[0.104,2.118],[0.106,2.094],[0.127,2.076],[0.113,2.061],[0.115,2.032],[0.136,2.014],[0.118,1.994],[0.119,1.979],[0.144,1.957],[0.126,1.936],[0.128,1.917],[0.148,1.899],[0.135,1.879],[0.137,1.855],[0.157,1.837],[0.144,1.822],[0.146,1.798],[0.166,1.78],[0.153,1.764],[0.149,1.745],[0.175,1.718],[0.157,1.702],[0.158,1.683],[0.184,1.66],[0.166,1.64],[0.167,1.62],[0.188,1.603],[0.17,1.577],[0.171,1.568],[0.197,1.54],[0.179,1.52],[0.18,1.505],[0.206,1.483],[0.188,1.462],[0.189,1.443],[0.21,1.425],[0.197,1.405],[0.198,1.381],[0.224,1.364],[0.201,1.338],[0.207,1.319],[0.227,1.306],[0.21,1.28],[0.211,1.266],[0.219,1.255],[0.229,1.255],[0.241,1.244],[0.219,1.223],[0.22,1.204],[0.245,1.186],[0.223,1.156],[0.229,1.142],[0.254,1.124],[0.236,1.108],[0.233,1.089],[0.241,1.077],[0.25,1.078],[0.263,1.067],[0.241,1.041],[0.242,1.027],[0.272,1.005],[0.249,0.984],[0.251,0.965],[0.281,0.947],[0.258,0.926],[0.26,0.902],[0.282,0.897],[0.295,0.885],[0.263,0.85],[0.264,0.835],[0.287,0.825],[0.3,0.813],[0.3,0.804],[0.264,0.777],[0.27,0.753],[0.29,0.745],[0.296,0.731],[0.28,0.713],[0.259,0.704],[0.261,0.68],[0.286,0.663],[0.271,0.64],[0.256,0.639],[0.241,0.616],[0.267,0.589],[0.251,0.566],[0.228,0.56],[0.221,0.552],[0.222,0.533],[0.243,0.515],[0.218,0.455],[0.161,0.369],[0.123,0.33],[0.09,0.309],[0.039,0.25],[0.014,0.195]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{}}},"bounds":{"min":[0.0001,0,-0.51],"max":[2.1657,2.768,0.51]},"volume_in3":2.1377,"centroid":[1.0545,0.9521,0],"shell":[1.0345,1.2404,0],"area_in2":35.3568,"triangles":31806,"manifold":true,"slabs":[[0,0,-0.51,2.166,0.395,0.51],[0.178,0.395,-0.468,1.974,0.791,0.468],[0.17,0.791,-0.46,1.907,1.582,0.46],[0.071,1.582,-0.46,1.843,2.373,0.46],[0.065,2.373,-0.46,1.782,2.768,0.46]],"slots":["body"]},"blackdog-22lr-15":{"part":"blackdog-22lr-15","model":"blackdog-22lr-15.glb","script":"blackdog_22lr_15.py","inputs":{"blackdog-22lr-15.base_slot_front_end_from_front":0.688,"blackdog-22lr-15.base_slot_length":0.998,"blackdog-22lr-15.base_slot_width":0.4,"blackdog-22lr-15.boss_diameter":0.185,"blackdog-22lr-15.boss_dimple_diameter":0.09,"blackdog-22lr-15.catch_lip_bottom":1.859,"blackdog-22lr-15.catch_lip_proud":0.026,"blackdog-22lr-15.catch_notch_front_x":1.048,"blackdog-22lr-15.catch_notch_height":0.3,"blackdog-22lr-15.catch_notch_rear_x":0.481,"blackdog-22lr-15.catch_notch_top":1.44,"blackdog-22lr-15.catch_recess_depth":0.035,"blackdog-22lr-15.catch_recess_front_x":1.019,"blackdog-22lr-15.catch_recess_rear_x":0.51,"blackdog-22lr-15.feed_lip_block_base_width":0.6,"blackdog-22lr-15.feed_lip_block_bottom_below_top":1.508,"blackdog-22lr-15.feed_lip_block_front_x":1.155,"blackdog-22lr-15.feed_lip_block_height":0.867,"blackdog-22lr-15.feed_lip_block_neck_below_top":0.385,"blackdog-22lr-15.feed_lip_block_neck_width":0.396,"blackdog-22lr-15.feed_lip_block_rear_x":0.588,"blackdog-22lr-15.feed_lip_block_shoulder_below_top":0.705,"blackdog-22lr-15.feed_lip_block_shoulder_width":0.572,"blackdog-22lr-15.feed_lip_block_top_width":0.26,"blackdog-22lr-15.feed_lips_height":0.225,"blackdog-22lr-15.feed_lips_width":0.14,"blackdog-22lr-15.groove_front_depth":0.087,"blackdog-22lr-15.groove_middle_depth":0.028,"blackdog-22lr-15.groove_rear_depth":0.033,"blackdog-22lr-15.post_diameter":0.19,"blackdog-22lr-15.spine_rib_depth":0.15,"blackdog-22lr-15.spine_rib_width":0.441,"blackdog-22lr-15.wall_thickness":0.053,"blackdog-22lr-15.width":0.868},"profiles":{"side":[[0,-4.789],[0.006,-5.74],[0.044,-5.79],[0.119,-5.796],[0.932,-5.655],[1.119,-5.593],[1.281,-5.589],[2.473,-5.377],[2.523,-5.276],[2.524,-4.713],[2.515,-0.92],[2.449,-0.865],[1.701,-0.85],[1.669,-0.394],[1.606,-0.33],[1.655,-0.052],[1.595,-0.014],[1.409,0],[0.649,-0.101],[0.621,-0.237],[0.521,-0.317],[0.423,-0.827],[0.211,-0.862],[0.173,-0.893],[0.158,-1.172],[0.006,-1.245]]},"features":{"side":{"webs":[[[1.462,-1.999],[2.459,-2.01],[2.457,-2.178],[1.46,-2.167]],[[1.45,-3.037],[2.447,-3.048],[2.445,-3.21],[1.448,-3.199]],[[1.438,-4.08],[2.435,-4.092],[2.433,-4.266],[1.436,-4.254]],[[1.426,-5.113],[2.423,-5.124],[2.422,-5.275],[1.424,-5.263]],[[0.076,-1.994],[0.458,-1.999],[0.457,-2.155],[0.074,-2.151]],[[0.064,-3.044],[0.446,-3.048],[0.444,-3.222],[0.062,-3.218]],[[0.052,-4.076],[0.434,-4.08],[0.433,-4.237],[0.05,-4.233]],[[0.04,-5.126],[0.422,-5.13],[0.421,-5.275],[0.038,-5.271]]],"bosses":[[[0.204,-0.917],[0.343,-0.919],[0.342,-1.058],[0.203,-1.056]],[[2.257,-0.964],[2.396,-0.965],[2.394,-1.105],[2.255,-1.103]],[[0.203,-3.057],[0.342,-3.059],[0.34,-3.198],[0.201,-3.196]],[[2.256,-3.069],[2.395,-3.071],[2.393,-3.21],[2.254,-3.208]],[[0.212,-5.238],[0.351,-5.239],[0.35,-5.379],[0.211,-5.377]],[[2.226,-5.122],[2.365,-5.123],[2.364,-5.263],[2.225,-5.261]]],"post":[[[0.829,-4.068],[1.015,-4.07],[1.012,-4.255],[0.827,-4.253]]],"groove_rear":[[[0.388,-0.844],[0.515,-0.845],[0.458,-5.797],[0.331,-5.796]]],"groove_middle":[[[1.052,-0.851],[1.202,-0.853],[1.145,-5.805],[0.995,-5.804]]],"groove_front":[[[1.783,-1.074],[2.067,-1.078],[2.012,-5.815],[1.728,-5.812]]],"rails":[[[0.524,-1.577],[0.546,-2.204],[0.577,-3.074],[0.603,-3.829],[0.682,-4.313],[0.772,-4.802],[0.893,-5.366],[0.932,-5.357],[0.811,-4.794],[0.721,-4.306],[0.643,-3.826],[0.617,-3.072],[0.587,-2.202],[0.565,-1.575]],[[1.174,-1.584],[1.184,-2.211],[1.214,-3.081],[1.252,-3.838],[1.375,-4.322],[1.468,-4.81],[1.572,-5.293],[1.612,-5.284],[1.507,-4.802],[1.414,-4.313],[1.293,-3.832],[1.255,-3.08],[1.224,-2.21],[1.214,-1.583]],[[1.455,-1.314],[1.439,-2.213],[1.47,-3.084],[1.519,-3.829],[1.63,-4.324],[1.706,-4.731],[1.746,-4.724],[1.669,-4.317],[1.56,-3.824],[1.51,-3.083],[1.48,-2.213],[1.496,-1.315]]]}},"placement":{"side":{"plane":"xy","offset":{}}},"bounds":{"min":[0,-5.796,-0.46],"max":[2.524,0,0.434]},"volume_in3":11.2483,"centroid":[1.2775,-3.1229,0.0004],"shell":[1.282,-3.1017,-0.0028],"area_in2":64.76,"triangles":15270,"manifold":true,"slabs":[[0.004,-5.796,-0.434,2.29,-5.41,0.434],[0,-5.41,-0.46,2.524,-1.159,0.434],[0.159,-1.159,-0.434,2.516,-0.773,0.434],[0.433,-0.773,-0.292,1.696,-0.386,0.292],[0.508,-0.386,-0.198,1.662,0,0.198]],"slots":["body","lips","webs"]},"blackdog-22lr-25":{"part":"blackdog-22lr-25","model":"blackdog-22lr-25.glb","script":"blackdog_22lr_25.py","inputs":{"blackdog-22lr-15.boss_diameter":0.185,"blackdog-22lr-15.boss_dimple_diameter":0.09,"blackdog-22lr-15.catch_lip_bottom":1.859,"blackdog-22lr-15.catch_lip_proud":0.026,"blackdog-22lr-15.catch_notch_front_x":1.048,"blackdog-22lr-15.catch_notch_height":0.3,"blackdog-22lr-15.catch_notch_rear_x":0.481,"blackdog-22lr-15.catch_recess_depth":0.035,"blackdog-22lr-15.catch_recess_front_x":1.019,"blackdog-22lr-15.catch_recess_rear_x":0.51,"blackdog-22lr-15.feed_lip_block_bottom_below_top":1.508,"blackdog-22lr-15.feed_lip_block_front_x":1.155,"blackdog-22lr-15.feed_lip_block_neck_below_top":0.385,"blackdog-22lr-15.feed_lip_block_neck_width":0.396,"blackdog-22lr-15.feed_lip_block_rear_x":0.588,"blackdog-22lr-15.feed_lip_block_shoulder_below_top":0.705,"blackdog-22lr-15.feed_lip_block_shoulder_width":0.572,"blackdog-22lr-15.feed_lip_block_top_width":0.26,"blackdog-22lr-15.feed_lips_height":0.225,"blackdog-22lr-15.feed_lips_width":0.14,"blackdog-22lr-15.groove_front_depth":0.087,"blackdog-22lr-15.groove_middle_depth":0.028,"blackdog-22lr-15.groove_rear_depth":0.033,"blackdog-22lr-15.spine_rib_depth":0.15,"blackdog-22lr-15.spine_rib_width":0.441,"blackdog-22lr-15.wall_thickness":0.053,"blackdog-22lr-25.catch_notch_top":1.44,"blackdog-22lr-25.feed_lip_block_base_width":0.6,"blackdog-22lr-25.feed_lip_block_height":0.867,"blackdog-22lr-25.width":0.868},"profiles":{"side":[[-0.003,-1.276],[0.022,-3.383],[0.135,-4.624],[0.387,-5.795],[0.991,-7.739],[1.049,-7.815],[1.046,-7.913],[1.093,-7.964],[1.225,-7.972],[3.259,-7.384],[3.339,-7.32],[3.355,-7.23],[2.748,-5.156],[2.561,-4.158],[2.509,-3.417],[2.524,-0.944],[2.464,-0.884],[1.822,-0.885],[1.724,-0.854],[1.695,-0.468],[1.629,-0.35],[1.675,-0.069],[1.493,0],[0.659,-0.08],[0.626,-0.222],[0.518,-0.286],[0.409,-0.807],[0.388,-0.838],[0.153,-0.861],[0.123,-0.904],[0.128,-1.165],[0.023,-1.212]]},"features":{"side":{"groove_rear":[[[0.364,-1.36],[0.365,-1.447],[0.366,-1.664],[0.372,-2.098],[0.374,-2.533],[0.377,-2.968],[0.384,-3.402],[0.406,-3.833],[0.448,-4.26],[0.505,-4.685],[0.583,-5.105],[0.68,-5.523],[0.796,-5.936],[0.923,-6.348],[1.053,-6.758],[1.18,-7.17],[1.259,-7.427],[1.319,-7.634],[1.438,-7.611],[1.38,-7.404],[1.301,-7.147],[1.175,-6.736],[1.045,-6.325],[0.918,-5.913],[0.802,-5.5],[0.705,-5.083],[0.628,-4.662],[0.571,-4.237],[0.53,-3.81],[0.51,-3.378],[0.503,-2.944],[0.501,-2.509],[0.499,-2.074],[0.494,-1.64],[0.492,-1.423],[0.491,-1.336]]],"groove_middle":[[[1.029,-1.235],[1.03,-1.322],[1.032,-1.539],[1.035,-1.974],[1.035,-2.409],[1.036,-2.844],[1.039,-3.279],[1.054,-3.711],[1.091,-4.14],[1.146,-4.565],[1.22,-4.986],[1.317,-5.403],[1.433,-5.817],[1.561,-6.228],[1.689,-6.639],[1.814,-7.051],[1.892,-7.308],[1.943,-7.516],[2.085,-7.49],[2.035,-7.282],[1.957,-7.024],[1.833,-6.612],[1.704,-6.201],[1.577,-5.79],[1.46,-5.376],[1.364,-4.959],[1.291,-4.538],[1.236,-4.113],[1.2,-3.684],[1.188,-3.251],[1.184,-2.816],[1.184,-2.381],[1.185,-1.946],[1.182,-1.511],[1.182,-1.293],[1.182,-1.206]]],"groove_front":[[[1.765,-1.184],[1.766,-1.402],[1.725,-1.845],[1.669,-2.29],[1.667,-2.726],[1.663,-3.162],[1.698,-3.591],[1.746,-4.017],[1.798,-4.442],[1.868,-4.865],[1.961,-5.282],[2.074,-5.696],[2.193,-6.109],[2.323,-6.52],[2.445,-6.933],[2.521,-7.191],[2.581,-7.397],[2.865,-7.344],[2.804,-7.137],[2.729,-6.879],[2.608,-6.467],[2.477,-6.056],[2.357,-5.643],[2.245,-5.229],[2.151,-4.812],[2.087,-4.388],[2.04,-3.962],[2.003,-3.533],[1.977,-3.103],[1.972,-2.669],[1.966,-2.234],[2.014,-1.79],[2.05,-1.348],[2.05,-1.131]]],"bosses":[[[0.141,-0.912],[0.288,-0.884],[0.315,-1.032],[0.168,-1.059]],[[2.197,-1.027],[2.344,-0.999],[2.372,-1.146],[2.225,-1.174]],[[0.285,-4.465],[0.432,-4.437],[0.459,-4.585],[0.312,-4.612]],[[2.253,-4.226],[2.4,-4.199],[2.428,-4.346],[2.281,-4.374]],[[1.098,-7.523],[1.245,-7.495],[1.272,-7.642],[1.125,-7.67]],[[3.013,-7.174],[3.16,-7.147],[3.187,-7.294],[3.04,-7.322]]]}},"placement":{"side":{"plane":"xy","offset":{}}},"bounds":{"min":[-0.003,-7.972,-0.46],"max":[3.355,0,0.434]},"volume_in3":14.762,"centroid":[1.4994,-4.1407,0.0003],"shell":[1.4674,-3.9435,-0.003],"area_in2":60.7425,"triangles":13962,"manifold":true,"slabs":[[0.94,-7.972,-0.434,2.604,-7.573,0.434],[0.816,-7.573,-0.434,3.355,-7.175,0.434],[0.692,-7.175,-0.434,3.339,-6.776,0.434],[0.568,-6.776,-0.434,3.222,-6.378,0.434],[0.444,-6.378,-0.434,3.106,-5.979,0.434],[0.341,-5.979,-0.434,2.989,-5.58,0.434],[0.255,-5.58,-0.434,2.872,-5.182,0.434],[0.169,-5.182,-0.434,2.756,-4.783,0.434],[0.113,-4.783,-0.434,2.678,-4.385,0.434],[0.077,-4.385,-0.434,2.603,-3.986,0.434],[-0.003,-3.986,-0.46,2.549,-1.196,0.434],[0.059,-1.196,-0.434,2.524,-0.797,0.434],[0.411,-0.797,-0.294,1.72,-0.399,0.294],[0.494,-0.399,-0.202,1.675,0,0.202]],"slots":["body","lips","webs"]},"cloud-defensive-rein.body":{"part":"cloud-defensive-rein","component":"body","model":"cloud-defensive-rein.body.glb","script":"cloud_defensive_rein.py","inputs":{"cloud-defensive-rein.axis_above_mount":0.82,"cloud-defensive-rein.body_diameter":0.881,"cloud-defensive-rein.foot_front_x":2.734,"cloud-defensive-rein.foot_length":0.325,"cloud-defensive-rein.foot_spacing":0.929,"cloud-defensive-rein.head_diameter":1.3,"cloud-defensive-rein.length":6.17,"cloud-defensive-rein.lens_diameter":0.99,"cloud-defensive-rein.mount_row_offset":0.131,"cloud-defensive-rein.mount_thickness":0.187,"cloud-defensive-rein.mount_width":0.6,"cloud-defensive-rein.tail_button_diameter":0.73,"cloud-defensive-rein.tail_x":0.21},"profiles":{"side":[[-0.238,0.057],[-0.238,-0.057],[-0.234,-0.06],[-0.223,-0.167],[-0.205,-0.261],[-0.175,-0.34],[-0.138,-0.413],[-0.091,-0.492],[-0.056,-0.528],[-0.023,-0.535],[-0.001,-0.532],[0.014,-0.535],[0.047,-0.535],[0.051,-0.532],[0.076,-0.535],[0.087,-0.532],[0.343,-0.532],[0.409,-0.543],[0.413,-0.522],[0.841,-0.523],[0.849,-0.519],[0.852,-0.523],[0.917,-0.526],[0.95,-0.516],[0.979,-0.495],[0.997,-0.499],[1.166,-0.499],[1.17,-0.496],[1.22,-0.499],[1.253,-0.492],[1.26,-0.496],[1.285,-0.493],[1.314,-0.496],[1.321,-0.493],[1.325,-0.496],[1.328,-0.489],[1.346,-0.493],[1.379,-0.479],[1.384,-0.474],[1.384,-0.46],[1.397,-0.452],[1.829,-0.453],[1.833,-0.456],[1.876,-0.439],[1.993,-0.439],[1.997,-0.436],[2.032,-0.443],[2.036,-0.44],[2.224,-0.44],[2.263,-0.43],[2.291,-0.45],[2.316,-0.457],[2.337,-0.454],[2.341,-0.457],[2.38,-0.457],[2.383,-0.454],[2.415,-0.454],[2.419,-0.457],[2.426,-0.454],[2.475,-0.454],[2.479,-0.457],[2.482,-0.454],[2.496,-0.457],[2.507,-0.454],[2.51,-0.457],[2.532,-0.454],[2.535,-0.458],[2.549,-0.454],[2.56,-0.458],[2.574,-0.454],[2.648,-0.454],[2.651,-0.458],[2.658,-0.454],[2.746,-0.455],[2.775,-0.458],[2.799,-0.445],[2.834,-0.438],[2.845,-0.441],[3.882,-0.44],[3.917,-0.434],[3.93,-0.437],[3.939,-0.432],[3.948,-0.41],[3.994,-0.499],[4.035,-0.536],[4.049,-0.559],[4.065,-0.574],[4.096,-0.587],[4.106,-0.581],[4.123,-0.581],[4.127,-0.574],[4.137,-0.574],[4.144,-0.581],[4.147,-0.577],[4.163,-0.599],[4.192,-0.624],[4.23,-0.644],[4.261,-0.647],[4.295,-0.647],[4.298,-0.644],[4.36,-0.651],[4.367,-0.648],[4.47,-0.648],[4.473,-0.644],[4.48,-0.648],[4.49,-0.644],[4.517,-0.648],[4.589,-0.644],[4.593,-0.648],[4.695,-0.648],[4.739,-0.654],[4.746,-0.648],[4.753,-0.651],[4.756,-0.648],[5.035,-0.648],[5.038,-0.645],[5.041,-0.648],[5.055,-0.645],[5.177,-0.648],[5.187,-0.645],[5.261,-0.651],[5.268,-0.648],[5.336,-0.651],[5.349,-0.645],[5.363,-0.648],[5.373,-0.645],[5.561,-0.648],[5.565,-0.651],[5.578,-0.648],[5.591,-0.651],[5.618,-0.648],[5.622,-0.651],[5.632,-0.645],[5.635,-0.648],[5.672,-0.645],[5.699,-0.648],[5.712,-0.645],[5.726,-0.648],[5.746,-0.645],[5.749,-0.648],[5.752,-0.645],[5.776,-0.648],[6.067,-0.645],[6.073,-0.648],[6.083,-0.645],[6.087,-0.648],[6.097,-0.645],[6.1,-0.648],[6.113,-0.645],[6.136,-0.652],[6.156,-0.648],[6.181,-0.627],[6.181,-0.594],[6.203,-0.596],[6.225,-0.578],[6.245,-0.539],[6.268,-0.46],[6.288,-0.349],[6.301,-0.221],[6.304,-0.1],[6.308,-0.096],[6.308,0.097],[6.304,0.1],[6.301,0.221],[6.288,0.349],[6.258,0.5],[6.238,0.556],[6.225,0.573],[6.225,0.579],[6.203,0.598],[6.181,0.593],[6.181,0.626],[6.156,0.647],[6.136,0.651],[6.113,0.645],[6.07,0.648],[6.067,0.645],[6.017,0.646],[6.013,0.649],[6,0.646],[5.996,0.649],[5.986,0.646],[5.98,0.649],[5.96,0.646],[5.953,0.65],[5.926,0.647],[5.923,0.65],[5.92,0.647],[5.809,0.648],[5.806,0.645],[5.803,0.648],[5.598,0.647],[5.591,0.65],[5.578,0.647],[5.565,0.651],[5.561,0.647],[5.447,0.649],[5.443,0.645],[5.363,0.649],[5.349,0.646],[5.346,0.65],[5.339,0.646],[5.332,0.65],[5.322,0.647],[5.319,0.65],[5.315,0.647],[5.268,0.647],[5.261,0.651],[5.187,0.645],[5.096,0.649],[5.089,0.646],[5.082,0.649],[5.079,0.646],[5.072,0.649],[5.038,0.643],[5.035,0.646],[4.766,0.649],[4.756,0.646],[4.749,0.65],[4.746,0.646],[4.739,0.653],[4.729,0.653],[4.695,0.647],[4.593,0.648],[4.589,0.645],[4.517,0.649],[4.49,0.646],[4.48,0.649],[4.476,0.646],[4.367,0.647],[4.36,0.65],[4.298,0.644],[4.295,0.648],[4.261,0.648],[4.23,0.645],[4.192,0.626],[4.147,0.576],[4.144,0.579],[4.137,0.573],[4.127,0.573],[4.123,0.58],[4.106,0.58],[4.096,0.587],[4.065,0.574],[4.049,0.559],[4.035,0.536],[3.994,0.499],[3.948,0.411],[3.939,0.433],[3.93,0.438],[3.917,0.435],[3.913,0.438],[3.588,0.441],[3.584,0.438],[3.525,0.438],[3.518,0.442],[3.512,0.439],[3.498,0.442],[3.494,0.439],[3.292,0.441],[3.289,0.437],[3.09,0.442],[3.083,0.439],[3.072,0.443],[3.069,0.439],[3.065,0.443],[3.058,0.439],[3.055,0.443],[3.048,0.439],[3.041,0.443],[3.034,0.44],[3.009,0.443],[3.006,0.44],[2.845,0.441],[2.834,0.438],[2.799,0.445],[2.775,0.459],[2.694,0.456],[2.69,0.453],[2.51,0.458],[2.507,0.454],[2.496,0.458],[2.482,0.455],[2.479,0.458],[2.475,0.455],[2.426,0.455],[2.419,0.459],[2.387,0.452],[2.341,0.456],[2.337,0.453],[2.316,0.456],[2.291,0.45],[2.263,0.43],[2.224,0.44],[2.036,0.438],[2.032,0.442],[1.997,0.435],[1.993,0.439],[1.876,0.44],[1.833,0.457],[1.78,0.451],[1.397,0.451],[1.384,0.46],[1.384,0.473],[1.379,0.478],[1.346,0.492],[1.328,0.489],[1.325,0.496],[1.321,0.493],[1.314,0.496],[1.285,0.493],[1.26,0.497],[1.253,0.493],[1.21,0.5],[1.206,0.497],[0.997,0.499],[0.979,0.496],[0.95,0.517],[0.917,0.527],[0.863,0.524],[0.849,0.518],[0.841,0.521],[0.551,0.524],[0.547,0.52],[0.413,0.522],[0.411,0.541],[0.398,0.542],[0.343,0.533],[0.241,0.534],[0.237,0.53],[0.014,0.536],[-0.001,0.533],[-0.023,0.536],[-0.048,0.533],[-0.076,0.511],[-0.08,0.501],[-0.105,0.47],[-0.164,0.363],[-0.205,0.26],[-0.223,0.167],[-0.234,0.06]]},"features":{"side":{"latch_face":[[[0.464,0.211],[0.794,0.208],[0.794,-0.021],[0.464,-0.019]]],"latch_edge":[[[0.496,0.622],[0.809,0.619],[0.809,0.527],[0.496,0.53]],[[0.434,-0.524],[0.762,-0.524],[0.762,-0.627],[0.434,-0.627]]],"bezel_flat":[[[5.315,0.001],[6.22,-0.004],[6.22,-0.28],[5.315,-0.276]]],"grip_flat":[[[1.547,0.176],[2.859,0.167],[2.859,-0.177],[1.547,-0.171]]],"seams":[[[0.405,0.568],[0.427,0.568],[0.427,0.52],[0.405,0.52]],[[4.712,0.665],[4.732,0.665],[4.732,0.618],[4.712,0.618]]]}},"placement":{"side":{"plane":"xy","offset":{"x":"tail_x","y":"axis_above_mount"}}},"bounds":{"min":[0.21,0.1665,-0.7845],"max":[6.384,1.4735,0.5225]},"volume_in3":5.5896,"centroid":[3.6423,0.8148,-0.131],"shell":[3.414,0.8086,-0.131],"area_in2":27.8615,"triangles":22806,"manifold":true,"slabs":[[0.21,0.281,-0.67,0.596,1.359,0.408],[0.596,0.196,-0.755,1.368,1.444,0.493],[1.368,0.187,-0.627,2.139,1.316,0.365],[2.139,0.329,-0.587,2.525,1.24,0.325],[2.525,0.187,-0.587,2.911,1.24,0.325],[2.911,0.278,-0.589,3.297,1.258,0.327],[3.297,0.382,-0.569,4.069,1.258,0.307],[4.069,0.167,-0.784,6.384,1.473,0.522]],"slots":["body","lens","button","latch"]},"cloud-defensive-rein.mlok":{"part":"cloud-defensive-rein","component":"mlok","model":"cloud-defensive-rein.mlok.glb","script":"cloud_defensive_rein.py","inputs":{"cloud-defensive-rein.axis_above_mount":0.82,"cloud-defensive-rein.body_diameter":0.881,"cloud-defensive-rein.foot_front_x":2.734,"cloud-defensive-rein.foot_length":0.325,"cloud-defensive-rein.foot_spacing":0.929,"cloud-defensive-rein.head_diameter":1.3,"cloud-defensive-rein.length":6.17,"cloud-defensive-rein.lens_diameter":0.99,"cloud-defensive-rein.lug_spacing":0.7874,"cloud-defensive-rein.lug_x":0.3,"cloud-defensive-rein.mount_bevel":0.08,"cloud-defensive-rein.mount_bevel_length":1.52,"cloud-defensive-rein.mount_hole_diameter":0.176,"cloud-defensive-rein.mount_hole_from_lug":1.559,"cloud-defensive-rein.mount_hole_spacing":0.833,"cloud-defensive-rein.mount_length":3.14,"cloud-defensive-rein.mount_pocket_diameter":0.384,"cloud-defensive-rein.mount_rear_radius":0.2,"cloud-defensive-rein.mount_row_offset":0.131,"cloud-defensive-rein.mount_row_stagger":0.169,"cloud-defensive-rein.mount_thickness":0.187,"cloud-defensive-rein.mount_width":0.6,"cloud-defensive-rein.tail_button_diameter":0.73,"cloud-defensive-rein.tail_x":0.21},"profiles":{},"bounds":{"min":[0,0,-0.3],"max":[3.14,0.187,0.3]},"volume_in3":0.3094,"centroid":[1.6438,0.0883,-0.0038],"shell":[1.5905,0.0884,0.0027],"area_in2":5.3,"triangles":2332,"manifold":true,"slabs":[[0,0,-0.3,3.14,0.187,0.3]],"slots":["mount"]},"cmmg-lower-parts-kit.grip":{"part":"cmmg-lower-parts-kit","component":"grip","model":"cmmg-lower-parts-kit.grip.glb","script":"cmmg_lower_parts_kit.py","inputs":{"cmmg-lower-parts-kit.grip_body_width":0.885,"cmmg-lower-parts-kit.grip_depth":3.284,"cmmg-lower-parts-kit.grip_edge_r":0.06,"cmmg-lower-parts-kit.grip_front_x":1.175,"cmmg-lower-parts-kit.grip_height":3.8535,"cmmg-lower-parts-kit.grip_rake":30,"cmmg-lower-parts-kit.grip_slot_width":0.3825,"cmmg-lower-parts-kit.grip_top_y":-1.0695,"cmmg-lower-parts-kit.grip_width":1.27,"std.ar15.deck_y":0.2485,"std.ar15.grip_lug_depth":0.93,"std.ar15.grip_lug_face_angle":60,"std.ar15.grip_lug_face_from_pin":1.228,"std.ar15.grip_lug_front_from_rear_face":2.3,"std.ar15.grip_lug_length":1.25,"std.ar15.grip_lug_width":0.375,"std.ar15.grip_seat_below_deck":1.318,"std.ar15.lower_body_width":0.88,"std.ar15.rear_underside_arc_center_below_seat":0.1928,"std.ar15.rear_underside_arc_center_x":-1.0238,"std.ar15.rear_underside_arc_r_fullest":0.716,"std.ar15.rear_underside_round_r":0.44,"std.ar15.receiver_rear_x":-1.125},"profiles":{"grip_side":[[-3.333,-3.198],[-3.311,-3.261],[-3.266,-3.316],[-3.266,-3.353],[-3.227,-3.37],[-1.639,-3.766],[-1.62,-3.785],[-1.45,-3.796],[-1.339,-3.748],[-1.278,-3.679],[-1.278,-3.627],[-1.333,-3.553],[-1.359,-3.468],[-1.348,-3.324],[-0.974,-2.65],[-0.926,-2.609],[-0.922,-2.565],[-0.77,-2.302],[-0.724,-2.252],[-0.62,-2.196],[-0.32,-2.163],[-0.278,-2.128],[-0.278,-2.05],[-0.389,-1.902],[-0.411,-1.846],[-0.418,-1.72],[-0.378,-1.613],[-0.178,-1.25],[-0.139,-1.218],[-0.004,-1.205],[0,-0.676],[-0.011,-0.239],[-0.083,-0.067],[-0.109,-0.067],[-0.154,-0.019],[-0.246,0],[-0.828,0],[-1.441,-0.017],[-1.459,-0.28],[-1.481,-0.365],[-1.552,-0.517],[-1.646,-0.641],[-1.741,-0.657],[-1.741,-0.698],[-1.711,-0.72],[-1.722,-0.765],[-1.985,-1.139],[-2.018,-1.161],[-2.018,-1.187],[-2.4,-1.735],[-2.441,-1.768],[-2.441,-1.791],[-3.17,-2.842],[-3.226,-2.894],[-3.226,-2.92],[-3.292,-3.005],[-3.326,-3.076]],"grip_section":[[0,-0.022],[0.036,-0.208],[0.111,-0.334],[0.297,-0.496],[0.451,-0.545],[0.452,-0.569],[0.604,-0.586],[0.643,-0.629],[0.857,-0.628],[0.887,-0.599],[0.996,-0.635],[1.201,-0.618],[1.241,-0.57],[1.262,-0.6],[1.323,-0.558],[1.372,-0.577],[1.458,-0.529],[1.958,-0.406],[2.148,-0.225],[2.157,-0.003],[2.14,0.223],[2.045,0.28],[1.951,0.404],[1.289,0.574],[1.273,0.605],[1.212,0.617],[1.213,0.584],[0.9,0.603],[0.874,0.635],[0.623,0.609],[0.559,0.565],[0.476,0.578],[0.43,0.54],[0.306,0.521],[0.078,0.281],[0.015,0.125]],"grip_front":[[-0.686,-2.596],[-0.667,-3.36],[-0.61,-3.641],[-0.545,-3.747],[-0.391,-3.874],[-0.065,-3.878],[-0.038,-3.897],[0.327,-3.886],[0.429,-3.817],[0.515,-3.717],[0.553,-3.625],[0.594,-3.39],[0.621,-2.813],[0.594,-1.711],[0.53,-0.929],[0.439,-0.431],[0.446,-0.063],[0.41,-0.011],[0.315,0],[0,0],[-0.431,-0.017],[-0.446,-0.412],[-0.53,-0.792],[-0.617,-1.381],[-0.67,-2.038]]},"features":{"grip_side":{"knurl":[[[-1.505,-0.961],[-1.124,-1.091],[-0.78,-1.217],[-0.717,-1.383],[-0.728,-1.505],[-0.902,-1.802],[-1.05,-2.05],[-1.15,-2.246],[-1.372,-2.591],[-1.568,-2.987],[-1.691,-3.209],[-1.791,-3.309],[-1.987,-3.32],[-2.209,-3.257],[-2.457,-3.183],[-2.653,-3.124],[-2.802,-3.061],[-2.839,-2.939],[-2.828,-2.839],[-2.753,-2.716],[-2.653,-2.542],[-2.457,-2.246],[-2.261,-1.976],[-1.987,-1.605],[-1.742,-1.235],[-1.594,-1.035]]]},"grip_section":{},"grip_front":{}},"placement":{"grip_side":{"plane":"xy","offset":{"x":"grip_front_x","y":"grip_top_y"}},"grip_section":{"plane":"xz","offset":{}},"grip_front":{"plane":"zy","offset":{"y":"grip_top_y"}}},"bounds":{"min":[-2.158,-4.8655,-0.195],"max":[1.175,-1.0695,1.075]},"volume_in3":6.8696,"centroid":[-0.3913,-3.0753,0.4375],"shell":[-0.2753,-2.9078,0.4379],"area_in2":25.7924,"triangles":2090,"manifold":true,"receiver":{"slot":{"width":0.3825,"clear_of_lug":0.0038,"rear_x":-1.2538,"floor_at_rear_y":-0.3073,"foot_x":-0.1688,"bottom_y":-0.9338},"scoop":{"axis_x":-2.1988,"axis_y":-0.1928,"on_centre_plane_r":0.7122,"across_r":0.4437}},"slabs":[[-1.866,-4.865,-0.164,-0.103,-4.486,1.014],[-2.158,-4.486,-0.195,-0.014,-4.106,1.075],[-2.132,-4.106,-0.195,0.197,-3.727,1.075],[-1.867,-3.727,-0.195,0.427,-3.347,1.075],[-1.604,-3.347,-0.195,0.897,-2.967,1.075],[-1.34,-2.967,-0.195,0.849,-2.588,1.075],[-1.074,-2.588,-0.195,1.172,-2.208,1.075],[-0.81,-2.208,-0.195,1.174,-1.829,1.075],[-0.566,-1.829,-0.087,1.175,-1.449,0.943],[-0.313,-1.449,-0.005,1.168,-1.069,0.886]],"slots":["grip"]},"cmmg-lower-parts-kit.guard":{"part":"cmmg-lower-parts-kit","component":"guard","model":"cmmg-lower-parts-kit.guard.glb","script":"cmmg_lower_parts_kit.py","inputs":{"cmmg-lower-parts-kit.guard_bar_t":0.09,"cmmg-lower-parts-kit.guard_edge_break":0.01,"cmmg-lower-parts-kit.guard_end_height":0.25,"cmmg-lower-parts-kit.guard_end_r":0.125,"cmmg-lower-parts-kit.guard_fillet_r":0.25,"cmmg-lower-parts-kit.guard_front_hole_y":-2.18,"cmmg-lower-parts-kit.guard_hole_above_bottom":0.125,"cmmg-lower-parts-kit.guard_hole_from_end":0.125,"cmmg-lower-parts-kit.guard_hole_spacing":1.844,"cmmg-lower-parts-kit.guard_length":2.09,"cmmg-lower-parts-kit.guard_width":0.43,"std.ar15.lower_body_width":0.88,"std.ar15.trigger_guard_ears_width":0.659,"std.ar15.trigger_guard_front_hole_d":0.1265,"std.ar15.trigger_guard_front_spotface_floor":0.3219,"std.ar15.trigger_guard_rear_hole_d":0.1285,"std.ar15.trigger_guard_rear_x":1.4985,"std.ar15.trigger_guard_rear_y":-2.18},"profiles":{},"bounds":{"min":[1.3736,-2.305,0.1125],"max":[3.4674,-2.0553,0.7675]},"volume_in3":0.1231,"centroid":[2.3875,-2.2227,0.4452],"shell":[2.3767,-2.2246,0.4485],"area_in2":2.8818,"triangles":1020,"manifold":true,"holes":{"rear":{"x":1.4985,"y":-2.18,"d":0.1285},"front":{"x":3.3425,"y":-2.18,"d":0.1265}},"slabs":[[1.374,-2.305,0.113,1.723,-2.055,0.767],[1.723,-2.305,0.225,3.118,-2.2,0.655],[3.118,-2.305,0.225,3.467,-2.055,0.762]],"slots":["guard","controls","plunger"]},"cmmg-lower-parts-kit.selector":{"part":"cmmg-lower-parts-kit","component":"selector","model":"cmmg-lower-parts-kit.selector.glb","script":"brought_selectors.py","inputs":{"cmmg-safety-selector.hub_d":0.48,"cmmg-safety-selector.hub_t":0.05,"cmmg-safety-selector.lever_reach":0.81,"cmmg-safety-selector.lever_standoff":0.25,"cmmg-safety-selector.paddle_base_t":0.125,"cmmg-safety-selector.paddle_relief":0.015,"cmmg-safety-selector.paddle_relief_start":0.281,"cmmg-safety-selector.paddle_start":0.09,"cmmg-safety-selector.paddle_width":0.25,"cmmg-safety-selector.pointer_angle":60,"cmmg-safety-selector.pointer_fillet_r":0.09,"cmmg-safety-selector.pointer_reach":0.34,"cmmg-safety-selector.shaft_d":0.37225,"cmmg-safety-selector.shaft_end_chamfer":0.024,"cmmg-safety-selector.shaft_length":0.9375,"cmmg-safety-selector.step_1_height":0.17,"cmmg-safety-selector.step_1_inset":0.009,"cmmg-safety-selector.step_2_height":0.2,"cmmg-safety-selector.step_2_inset":0.025,"cmmg-safety-selector.step_3_height":0.22,"cmmg-safety-selector.step_3_inset":0.043,"cmmg-safety-selector.step_4_height":0.24,"cmmg-safety-selector.step_4_inset":0.075,"cmmg-safety-selector.step_5_inset":0.11,"std.ar15.lower_body_width":0.88,"std.ar15.selector_hole_d":0.376,"std.ar15.selector_x":0.803,"std.ar15.selector_y":-0.466},"profiles":{},"bounds":{"min":[-0.007,-0.7058,-0.25],"max":[1.143,-0.2262,0.9375]},"volume_in3":0.1423,"centroid":[0.703,-0.466,0.3065],"shell":[0.665,-0.466,0.2352],"area_in2":2.158,"triangles":6464,"manifold":true,"slabs":[[-0.007,-0.706,-0.25,1.143,-0.226,0.146],[0.617,-0.652,0.146,0.989,-0.28,0.938]],"slots":["controls"]},"cmmg-lower-parts-kit.trigger":{"part":"cmmg-lower-parts-kit","component":"trigger","model":"cmmg-lower-parts-kit.trigger.glb","script":"cmmg_lower_parts_kit.py","inputs":{"cmmg-lower-parts-kit.trigger_edge_r":0.031,"cmmg-lower-parts-kit.trigger_face_x":1.9735,"cmmg-lower-parts-kit.trigger_rest_angle":-1,"std.ar15.lower_body_width":0.88,"std.ar15.trigger_body_width":0.29,"std.ar15.trigger_boss_d":0.3145,"std.ar15.trigger_boss_length":0.664,"std.ar15.trigger_pin_x":1.928,"std.ar15.trigger_pin_y":-0.689,"std.ar15.trigger_tail_behind_pivot":1.2025},"profiles":{"trigger":[[-1.204,-0.232],[-1.187,-0.265],[-0.105,-0.271],[-0.09,-0.286],[-0.09,-0.371],[-0.052,-0.403],[-0.046,-0.457],[-0.09,-0.552],[-0.125,-0.701],[-0.113,-0.98],[-0.078,-1.095],[0.005,-1.247],[0.005,-1.272],[0.152,-1.423],[0.203,-1.433],[0.224,-1.415],[0.224,-1.377],[0.125,-1.237],[0.068,-1.053],[0.062,-0.946],[0.078,-0.831],[0.095,-0.807],[0.125,-0.809],[0.125,-0.781],[0.1,-0.761],[0.103,-0.736],[0.186,-0.593],[0.247,-0.528],[0.378,-0.427],[0.493,-0.381],[0.493,-0.181],[0.514,-0.132],[0.769,-0.133],[0.788,0.044],[0.292,0.049],[0.263,0.011],[0.2,0.005],[0.163,0.025],[0.098,0.135],[-0.016,0.163],[-0.108,0.132],[-0.144,0.092],[-0.163,0.038],[-0.197,0.008],[-0.225,0.005],[-0.263,0.008],[-0.298,0.049],[-0.333,0.056],[-1.12,0.059],[-1.19,0.046],[-1.201,0.038]]},"features":{"trigger":{}},"placement":{"trigger":{"plane":"xy","offset":{}}},"bounds":{"min":[0.7201,-2.1253,0.108],"max":[2.7166,-0.5257,0.772]},"volume_in3":0.2918,"centroid":[1.7883,-0.943,0.44],"shell":[1.7968,-0.9918,0.44],"area_in2":4.1853,"triangles":2072,"manifold":true,"slabs":[[0.72,-0.951,0.295,1.519,-0.61,0.585],[1.519,-1.969,0.108,1.918,-0.526,0.772],[1.918,-2.125,0.108,2.317,-0.527,0.772],[2.317,-1.115,0.295,2.717,-0.648,0.585]],"slots":["controls"]},"cmmg-safety-selector":{"part":"cmmg-safety-selector","model":"cmmg-safety-selector.glb","script":"cmmg_safety_selector.py","inputs":{"cmmg-safety-selector.hub_d":0.48,"cmmg-safety-selector.hub_t":0.05,"cmmg-safety-selector.lever_reach":0.81,"cmmg-safety-selector.lever_standoff":0.25,"cmmg-safety-selector.paddle_base_t":0.125,"cmmg-safety-selector.paddle_relief":0.015,"cmmg-safety-selector.paddle_relief_start":0.281,"cmmg-safety-selector.paddle_start":0.09,"cmmg-safety-selector.paddle_width":0.25,"cmmg-safety-selector.pointer_angle":60,"cmmg-safety-selector.pointer_fillet_r":0.09,"cmmg-safety-selector.pointer_reach":0.34,"cmmg-safety-selector.shaft_d":0.37225,"cmmg-safety-selector.shaft_end_chamfer":0.024,"cmmg-safety-selector.shaft_length":0.9375,"cmmg-safety-selector.step_1_height":0.17,"cmmg-safety-selector.step_1_inset":0.009,"cmmg-safety-selector.step_2_height":0.2,"cmmg-safety-selector.step_2_inset":0.025,"cmmg-safety-selector.step_3_height":0.22,"cmmg-safety-selector.step_3_inset":0.043,"cmmg-safety-selector.step_4_height":0.24,"cmmg-safety-selector.step_4_inset":0.075,"cmmg-safety-selector.step_5_inset":0.11,"std.ar15.lower_body_width":0.88,"std.ar15.selector_hole_d":0.376},"profiles":{},"bounds":{"min":[-0.81,-0.2398,-0.69],"max":[0.34,0.2398,0.4975]},"volume_in3":0.1423,"centroid":[-0.1,0,-0.1335],"shell":[-0.138,0,-0.2048],"area_in2":2.158,"triangles":6464,"manifold":true,"slabs":[[-0.81,-0.24,-0.69,0.34,0.24,-0.294],[-0.186,-0.186,-0.294,0.186,0.186,0.498]],"slots":["body"]},"daniel-defense-103-barrel":{"part":"daniel-defense-103-barrel","model":"daniel-defense-103-barrel.glb","script":"daniel_defense_103_barrel.py","inputs":{"daniel-defense-103-barrel.barrel_ahead_of_flange":9.68,"daniel-defense-103-barrel.bore_d":0.219,"daniel-defense-103-barrel.chamber_front_x":0.781,"daniel-defense-103-barrel.chamber_od":0.993,"daniel-defense-103-barrel.collar_od":0.85,"daniel-defense-103-barrel.collar_rear_x":6.324,"daniel-defense-103-barrel.extension_lug_bore_d":0.572,"daniel-defense-103-barrel.extension_lug_count":8,"daniel-defense-103-barrel.extension_lug_depth":0.214,"daniel-defense-103-barrel.extension_lug_rear_cone":0.099,"daniel-defense-103-barrel.extension_mouth_d":0.77,"daniel-defense-103-barrel.extension_od":0.999,"daniel-defense-103-barrel.extension_rear_x":-0.99,"daniel-defense-103-barrel.extension_recess_d":0.83,"daniel-defense-103-barrel.extension_recess_depth":0.595,"daniel-defense-103-barrel.extension_slot_floor":0.38,"daniel-defense-103-barrel.extension_slot_width":0.124,"daniel-defense-103-barrel.feed_ramp_angle":45,"daniel-defense-103-barrel.feed_ramp_axis_r":0.286,"daniel-defense-103-barrel.feed_ramp_d":0.28,"daniel-defense-103-barrel.flange_d":1.171,"daniel-defense-103-barrel.flange_front_x":0.131,"daniel-defense-103-barrel.flare_fillet":0.219,"daniel-defense-103-barrel.flare_rear_x":5.984,"daniel-defense-103-barrel.gas_port_d":0.07,"daniel-defense-103-barrel.gas_port_x":7.226,"daniel-defense-103-barrel.handguard_section_front_od":0.612,"daniel-defense-103-barrel.handguard_section_rear_od":0.688,"daniel-defense-103-barrel.index_pin_d":0.125,"daniel-defense-103-barrel.index_pin_top":0.581,"daniel-defense-103-barrel.index_pin_x":0.074,"daniel-defense-103-barrel.journal_front_x":8.802,"daniel-defense-103-barrel.journal_od":0.75,"daniel-defense-103-barrel.journal_rear_x":6.943,"daniel-defense-103-barrel.muzzle_od":0.74,"daniel-defense-103-barrel.outline_flange_front":1.189,"daniel-defense-103-barrel.outline_muzzle":11.006,"daniel-defense-103-barrel.overall_length":10.801,"daniel-defense-103-barrel.shoulder_x":9.178,"daniel-defense-103-barrel.taper_front_x":1.641,"daniel-defense-103-barrel.thread_length":0.633,"daniel-defense-103-barrel.thread_major_d":0.4957,"daniel-defense-103-barrel.thread_minor_d":0.4551,"daniel-defense-103-barrel.thread_pitch":0.03571},"profiles":{"side":[[0,0.417],[0.011,0.406],[0,0.395],[0.001,0.003],[0.002,-0.355],[0.013,-0.367],[0.013,-0.501],[0.03,-0.518],[0.053,-0.518],[0.064,-0.506],[0.075,-0.518],[0.444,-0.517],[0.456,-0.505],[1.038,-0.504],[1.043,-0.51],[1.044,-0.577],[1.06,-0.594],[1.184,-0.593],[1.194,-0.492],[1.206,-0.492],[1.217,-0.504],[1.833,-0.502],[1.844,-0.491],[1.922,-0.491],[1.933,-0.479],[1.978,-0.479],[1.989,-0.468],[2.045,-0.468],[2.056,-0.457],[2.112,-0.457],[2.124,-0.445],[2.18,-0.445],[2.191,-0.434],[2.247,-0.434],[2.258,-0.423],[2.314,-0.423],[2.325,-0.411],[2.381,-0.411],[2.392,-0.4],[2.437,-0.4],[2.448,-0.389],[2.504,-0.389],[2.515,-0.377],[2.571,-0.377],[2.582,-0.366],[2.638,-0.366],[2.65,-0.355],[2.717,-0.354],[2.728,-0.343],[4.094,-0.34],[4.105,-0.329],[5.46,-0.325],[5.471,-0.314],[7.038,-0.31],[7.049,-0.322],[7.116,-0.321],[7.128,-0.333],[7.172,-0.332],[7.184,-0.344],[7.217,-0.344],[7.228,-0.355],[7.251,-0.355],[7.262,-0.366],[7.296,-0.366],[7.307,-0.377],[7.329,-0.377],[7.363,-0.399],[7.385,-0.399],[7.441,-0.433],[8.091,-0.431],[8.107,-0.414],[8.113,-0.375],[9.098,-0.373],[9.109,-0.384],[9.188,-0.384],[9.994,-0.382],[10.005,-0.37],[10.24,-0.37],[10.251,-0.381],[10.341,-0.381],[10.369,-0.364],[10.369,-0.33],[10.38,-0.319],[10.38,-0.252],[10.408,-0.246],[10.43,-0.224],[10.452,-0.246],[10.475,-0.224],[10.486,-0.246],[10.497,-0.246],[10.508,-0.235],[10.52,-0.246],[10.531,-0.246],[10.542,-0.235],[10.553,-0.246],[10.564,-0.246],[10.576,-0.235],[10.587,-0.246],[10.598,-0.246],[10.609,-0.235],[10.62,-0.235],[10.632,-0.246],[10.643,-0.235],[10.654,-0.235],[10.665,-0.246],[10.676,-0.246],[10.688,-0.234],[10.699,-0.246],[10.71,-0.246],[10.721,-0.234],[10.732,-0.246],[10.744,-0.246],[10.755,-0.234],[10.766,-0.245],[10.777,-0.245],[10.788,-0.234],[10.822,-0.245],[10.833,-0.234],[10.844,-0.245],[10.855,-0.234],[10.867,-0.234],[10.878,-0.245],[10.889,-0.245],[10.9,-0.234],[10.911,-0.245],[10.923,-0.245],[10.934,-0.234],[10.945,-0.245],[10.967,-0.245],[10.973,-0.228],[10.995,-0.206],[10.995,-0.15],[11.006,-0.139],[11.006,0.108],[10.995,0.119],[10.995,0.13],[11.006,0.141],[10.995,0.153],[10.994,0.209],[10.966,0.236],[10.955,0.225],[10.944,0.248],[10.933,0.248],[10.922,0.225],[10.899,0.247],[10.888,0.225],[10.866,0.247],[10.854,0.236],[10.843,0.236],[10.832,0.247],[10.821,0.236],[10.81,0.236],[10.798,0.247],[10.776,0.225],[10.765,0.236],[10.754,0.236],[10.742,0.225],[10.72,0.247],[10.709,0.225],[10.698,0.225],[10.686,0.247],[10.681,0.23],[10.664,0.225],[10.653,0.247],[10.63,0.224],[10.619,0.247],[10.608,0.247],[10.597,0.224],[10.574,0.247],[10.563,0.224],[10.541,0.247],[10.535,0.23],[10.519,0.224],[10.507,0.247],[10.485,0.224],[10.474,0.246],[10.451,0.224],[10.44,0.246],[10.418,0.224],[10.407,0.246],[10.395,0.235],[10.379,0.241],[10.378,0.319],[10.367,0.33],[10.361,0.369],[10.003,0.368],[9.992,0.38],[8.111,0.375],[8.105,0.414],[8.089,0.431],[7.439,0.429],[7.383,0.396],[7.361,0.396],[7.327,0.373],[7.305,0.373],[7.294,0.362],[7.26,0.362],[7.249,0.351],[7.227,0.351],[7.216,0.339],[7.182,0.339],[7.171,0.328],[7.115,0.328],[7.104,0.317],[7.037,0.317],[7.025,0.305],[6.578,0.304],[6.566,0.315],[5.402,0.313],[5.391,0.324],[4.63,0.322],[4.618,0.333],[3.678,0.331],[3.667,0.342],[2.704,0.34],[2.693,0.351],[2.659,0.351],[2.648,0.362],[2.581,0.362],[2.569,0.373],[2.536,0.373],[2.525,0.384],[2.469,0.384],[2.457,0.395],[2.401,0.395],[2.39,0.406],[2.345,0.406],[2.334,0.417],[2.278,0.417],[2.267,0.428],[2.211,0.428],[2.2,0.439],[2.144,0.439],[2.133,0.45],[2.088,0.45],[2.077,0.461],[2.032,0.461],[2.021,0.472],[1.965,0.472],[1.953,0.483],[1.897,0.483],[1.886,0.494],[1.349,0.493],[1.338,0.504],[1.192,0.504],[1.186,0.51],[1.186,0.566],[1.198,0.577],[1.181,0.594],[1.058,0.593],[1.052,0.588],[1.052,0.52],[1.035,0.504],[1.024,0.515],[0.901,0.514],[0.89,0.503],[0.532,0.502],[0.52,0.502],[0.509,0.514],[0.028,0.512],[0.011,0.496],[0.011,0.428]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"x":"extension_rear_x"}}},"bounds":{"min":[-0.99,-0.5855,-0.5855],"max":[9.811,0.5855,0.5855]},"volume_in3":4.267,"centroid":[3.832,0.0003,0],"shell":[3.7439,0.001,0],"area_in2":38.4023,"triangles":15374,"manifold":true,"slabs":[[-0.99,-0.5,-0.5,-0.219,0.5,0.5],[-0.219,-0.586,-0.586,0.167,0.586,0.586],[0.167,-0.496,-0.496,1.324,0.496,0.496],[1.324,-0.4,-0.4,1.71,0.4,0.4],[1.71,-0.343,-0.343,5.953,0.343,0.343],[5.953,-0.425,-0.425,7.111,0.425,0.425],[7.111,-0.375,-0.375,9.425,0.375,0.375],[9.425,-0.248,-0.248,9.811,0.248,0.248]],"slots":["barrel","extension"]},"daniel-defense-bcg":{"part":"daniel-defense-bcg","model":"daniel-defense-bcg.glb","script":"daniel_defense_bcg.py","inputs":{"daniel-defense-bcg.length":6.672,"daniel-defense-bcg.od":0.994,"daniel-defense-bcg.stake_depth":0.048,"daniel-defense-bcg.stake_width":0.076,"std.ar15.carrier_body_od":0.93,"std.ar15.carrier_bolt_body_d":0.528,"std.ar15.carrier_bolt_cam_hole_to_face":1.305,"std.ar15.carrier_bolt_face_from_rear":2.675,"std.ar15.carrier_bolt_face_recess_d":0.38,"std.ar15.carrier_bolt_head_d":0.55,"std.ar15.carrier_bolt_length":2.8,"std.ar15.carrier_bolt_lug_length":0.278,"std.ar15.carrier_bolt_lug_od":0.743,"std.ar15.carrier_bolt_lug_offset":67.5,"std.ar15.carrier_bolt_lug_pitch":45,"std.ar15.carrier_bolt_lug_root_d":0.53,"std.ar15.carrier_bolt_lug_slot_width":0.102,"std.ar15.carrier_bolt_lugs":7,"std.ar15.carrier_bottom_cut_depth":0.215,"std.ar15.carrier_bottom_cut_rear":5.0965,"std.ar15.carrier_bottom_cut_rear_r":0.125,"std.ar15.carrier_cam_advance":0.255,"std.ar15.carrier_cam_advance_20":0.195,"std.ar15.carrier_cam_angle":22.5,"std.ar15.carrier_cam_dwell":0.042,"std.ar15.carrier_cam_pin_d":0.3105,"std.ar15.carrier_cam_pin_head_corner_d":0.47,"std.ar15.carrier_cam_pin_head_height":0.095,"std.ar15.carrier_cam_pin_head_length":0.32,"std.ar15.carrier_cam_pin_head_width":0.401,"std.ar15.carrier_cam_pin_hole_to_head":0.507,"std.ar15.carrier_cam_tail":0.07,"std.ar15.carrier_cam_width":0.3165,"std.ar15.carrier_cam_x":0.64,"std.ar15.carrier_cut_corner_r":0.12,"std.ar15.carrier_front_chamfer":0.075,"std.ar15.carrier_front_chamfer_angle":45,"std.ar15.carrier_front_flat_drop":0.095,"std.ar15.carrier_groove_angle":45,"std.ar15.carrier_groove_r":0.078,"std.ar15.carrier_groove_runout_from_shoulder":2.35,"std.ar15.carrier_groove_runout_r":1.5,"std.ar15.carrier_key_base_height":0.241,"std.ar15.carrier_key_bore_d":0.1805,"std.ar15.carrier_key_bore_depth":0.82,"std.ar15.carrier_key_cbore_d":0.273,"std.ar15.carrier_key_foot_length":1.31,"std.ar15.carrier_key_length":2.465,"std.ar15.carrier_key_mouth_angle":60,"std.ar15.carrier_key_mouth_d":0.225,"std.ar15.carrier_key_ramp_angle":45,"std.ar15.carrier_key_ramp_top":1.26,"std.ar15.carrier_key_screw_from_front":1.765,"std.ar15.carrier_key_screw_head_d":0.266,"std.ar15.carrier_key_screw_head_h":0.159,"std.ar15.carrier_key_screw_socket":0.125,"std.ar15.carrier_key_screw_socket_depth":0.077,"std.ar15.carrier_key_screw_spacing":0.5,"std.ar15.carrier_key_screw_x":2.055,"std.ar15.carrier_key_seat_front":1.37,"std.ar15.carrier_key_seat_rear":2.74,"std.ar15.carrier_key_seat_runout_r":0.5,"std.ar15.carrier_key_seat_y":0.42,"std.ar15.carrier_key_slot_width":0.4035,"std.ar15.carrier_key_step":0.03,"std.ar15.carrier_key_step_height":0.182,"std.ar15.carrier_key_tube_axis_y":0.361,"std.ar15.carrier_key_tube_d":0.25,"std.ar15.carrier_key_tube_length":0.9,"std.ar15.carrier_key_width":0.4005,"std.ar15.carrier_length":6.672,"std.ar15.carrier_pad_edge_angle":55,"std.ar15.carrier_pad_front":0.38,"std.ar15.carrier_rail_od":0.994,"std.ar15.carrier_rail_top_drop":0.67,"std.ar15.carrier_rear_chamfer":0.03,"std.ar15.carrier_rear_chamfer_angle":30,"std.ar15.carrier_relief_angle":75,"std.ar15.carrier_retaining_pin_csk_angle":82,"std.ar15.carrier_retaining_pin_csk_d":0.281,"std.ar15.carrier_retaining_pin_hole_d":0.093,"std.ar15.carrier_retaining_pin_x":2.536,"std.ar15.carrier_retaining_pin_y":0.157,"std.ar15.carrier_rib_bottom_drop":0.859,"std.ar15.carrier_rib_chamfer_across":0.87,"std.ar15.carrier_rib_chamfer_angle":22.5,"std.ar15.carrier_rib_rear":2.81,"std.ar15.carrier_rib_taper_angle":4.5,"std.ar15.carrier_rib_taper_start":1.8,"std.ar15.carrier_rib_width":0.399,"std.ar15.carrier_scallop_across":0.8125,"std.ar15.carrier_scallop_angle":22.5,"std.ar15.carrier_scallop_flat":0.375,"std.ar15.carrier_scallop_r":0.47,"std.ar15.carrier_scallop_rear":1.5,"std.ar15.carrier_serration_count":28,"std.ar15.carrier_serration_cutter_r":0.3125,"std.ar15.carrier_serration_depth":0.042,"std.ar15.carrier_serration_face_angle":70.5,"std.ar15.carrier_serration_flank_angle":22.25,"std.ar15.carrier_serration_front":1.9,"std.ar15.carrier_serration_pitch":0.125,"std.ar15.carrier_side_hole_d":0.125,"std.ar15.carrier_side_hole_x":2.15,"std.ar15.carrier_slab_height":0.5,"std.ar15.carrier_slot_travel":1.75,"std.ar15.carrier_slot_width":0.5,"std.ar15.carrier_tail_bore":0.625,"std.ar15.carrier_tail_front":5.1,"std.ar15.carrier_tail_notch_depth":0.1,"std.ar15.carrier_tail_notch_width":0.156,"std.ar15.carrier_top_cut_length":2.07,"std.ar15.carrier_vent_angle":45,"std.ar15.carrier_vent_d":0.109,"std.ar15.carrier_vent_x":1.34},"profiles":{},"bounds":{"min":[0,-0.4583,-0.4659],"max":[7.462,0.906,0.4659]},"volume_in3":2.9012,"centroid":[4.1793,0.0668,-0.0073],"shell":[3.7846,0.0996,0.0007],"area_in2":33.5972,"triangles":20352,"manifold":true,"slabs":[[0,-0.458,-0.465,1.964,0.465,0.465],[1.964,-0.25,-0.465,3.535,0.252,0.465],[3.535,-0.349,-0.466,4.713,0.661,0.466],[4.713,-0.362,-0.466,6.677,0.906,0.466],[6.677,-0.275,-0.275,7.069,0.275,0.275],[7.069,-0.368,-0.368,7.462,0.368,0.368]],"slots":["body","screws"]},"daniel-defense-fixed-front-sight":{"part":"daniel-defense-fixed-front-sight","model":"daniel-defense-fixed-front-sight.glb","script":"daniel_defense_fixed_front_sight.py","inputs":{"daniel-defense-fixed-front-sight.clamp_bottom_y":-0.235,"daniel-defense-fixed-front-sight.feet_inner_half":0.447,"daniel-defense-fixed-front-sight.front_x":0.5,"daniel-defense-fixed-front-sight.insert_d":0.205,"daniel-defense-fixed-front-sight.length":1,"daniel-defense-fixed-front-sight.post_behind_front":0.325,"daniel-defense-fixed-front-sight.post_blade":0.07,"daniel-defense-fixed-front-sight.post_blade_height":0.268,"daniel-defense-fixed-front-sight.post_flange_d":0.3645,"daniel-defense-fixed-front-sight.post_flange_thick":0.06,"daniel-defense-fixed-front-sight.post_notch_circle_d":0.4,"daniel-defense-fixed-front-sight.post_notch_r":0.0455,"daniel-defense-fixed-front-sight.post_root_d":0.165,"daniel-defense-fixed-front-sight.post_root_height":0.077,"daniel-defense-fixed-front-sight.screw_behind_front":0.499,"daniel-defense-fixed-front-sight.screw_below_rail":0.025,"daniel-defense-fixed-front-sight.screw_d":0.19,"daniel-defense-fixed-front-sight.screw_head_d":0.38,"daniel-defense-fixed-front-sight.screw_head_proud":0.032,"daniel-defense-fixed-front-sight.sight_line_above_rail":1.36,"daniel-defense-fixed-front-sight.slit_offset":0.181,"daniel-defense-fixed-front-sight.slit_top_above_rail":0.5,"daniel-defense-fixed-front-sight.slit_width":0.061,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{"side":[[-1,0.247],[-1,0.007],[-0.995,0],[-0.005,0],[0,0.003],[0,1.42],[-0.003,1.453],[-0.026,1.524],[-0.058,1.57],[-0.116,1.622],[-0.166,1.645],[-0.23,1.66],[-0.335,1.66],[-0.41,1.642],[-0.457,1.616],[-0.515,1.562],[-0.55,1.503],[-0.61,1.265],[-0.705,0.973],[-0.81,0.715],[-0.854,0.632],[-0.853,0.623],[-0.893,0.54],[-0.959,0.423],[-0.984,0.355]],"rear":[[-0.616,0.308],[-0.616,0.098],[-0.575,0.036],[-0.548,0.011],[-0.527,0],[-0.448,0],[-0.447,0.235],[0.445,0.235],[0.445,0],[0.523,0],[0.54,0.006],[0.572,0.036],[0.616,0.098],[0.616,0.308],[0.605,0.344],[0.557,0.392],[0.487,0.444],[0.429,0.468],[0.327,0.535],[0.273,0.554],[0.274,1.357],[0.307,1.538],[0.354,1.66],[0.263,1.66],[0.224,1.538],[0.176,1.353],[0.13,1.315],[-0.011,1.308],[-0.134,1.315],[-0.182,1.355],[-0.225,1.538],[-0.265,1.66],[-0.355,1.66],[-0.31,1.538],[-0.276,1.357],[-0.276,0.554],[-0.327,0.536],[-0.398,0.467],[-0.526,0.431],[-0.574,0.398],[-0.605,0.351]],"plan":[[-1,0.452],[-1,-0.454],[-0.729,-0.623],[-0.273,-0.623],[0,-0.452],[0,0],[0,0.45],[-0.262,0.623],[-0.729,0.623]]},"features":{"side":{"screw_head":[[[-0.687,0.399],[-0.31,0.399],[-0.31,0.023],[-0.687,0.023]]],"base_top":[[[-0.95,0.44],[-0.002,0.44],[-0.002,0.44],[-0.95,0.44]]]},"rear":{"post":[[[-0.036,1.565],[0.034,1.565],[0.034,1.308],[-0.036,1.308]]],"slits":[[[-0.212,0.736],[-0.152,0.736],[-0.152,0.236],[-0.212,0.236]],[[0.149,0.736],[0.211,0.736],[0.211,0.236],[0.149,0.236]]],"ceiling":[[[-0.298,0.236],[0.294,0.236],[0.294,0.236],[-0.298,0.236]]],"tower":[[[-0.275,1.355],[0.272,1.355],[0.272,0.553],[-0.275,0.553]]],"screw_head":[[[0.616,0.371],[0.648,0.371],[0.648,0.043],[0.616,0.043]]]},"plan":{}},"placement":{"side":{"plane":"xy","offset":{"x":"front_x","y":"clamp_bottom_y"}},"rear":{"plane":"zy","offset":{"y":"clamp_bottom_y"}},"plan":{"plane":"xz","offset":{"x":"front_x"}}},"bounds":{"min":[-0.5,-0.235,-0.618],"max":[0.5,1.425,0.648]},"volume_in3":0.6969,"centroid":[0.071,0.3833,0.0021],"shell":[0.0651,0.3612,0.012],"area_in2":9.9194,"triangles":5926,"manifold":true,"rail_seat":{"x":[-0.5,0.5],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.457},"slabs":[[-0.5,-0.235,-0.618,0.5,0.429,0.648],[-0.337,0.429,-0.276,0.5,0.761,0.274],[-0.198,0.761,-0.276,0.5,1.093,0.274],[-0.094,1.093,-0.355,0.5,1.425,0.354]],"slots":["body","hardware","insert"]},"daniel-defense-fixed-rear-sight":{"part":"daniel-defense-fixed-rear-sight","model":"daniel-defense-fixed-rear-sight.glb","script":"daniel_defense_fixed_rear_sight.py","inputs":{"daniel-defense-fixed-rear-sight.aperture_large_d":0.2,"daniel-defense-fixed-rear-sight.aperture_leg_thick":0.09,"daniel-defense-fixed-rear-sight.aperture_leg_top":0.185,"daniel-defense-fixed-rear-sight.aperture_leg_width":0.361,"daniel-defense-fixed-rear-sight.aperture_lying_reach":0.28,"daniel-defense-fixed-rear-sight.aperture_small_d":0.07,"daniel-defense-fixed-rear-sight.clamp_bottom_y":-0.228,"daniel-defense-fixed-rear-sight.drum_above_rail":1.047,"daniel-defense-fixed-rear-sight.drum_behind_front":0.582,"daniel-defense-fixed-rear-sight.drum_d":0.74,"daniel-defense-fixed-rear-sight.drum_hole_circle_d":0.546,"daniel-defense-fixed-rear-sight.drum_hole_d":0.1,"daniel-defense-fixed-rear-sight.drum_proud":0.043,"daniel-defense-fixed-rear-sight.front_x":0.69,"daniel-defense-fixed-rear-sight.hub_d":0.273,"daniel-defense-fixed-rear-sight.hub_proud":0.22,"daniel-defense-fixed-rear-sight.insert_d":0.2,"daniel-defense-fixed-rear-sight.left_head_d":0.38,"daniel-defense-fixed-rear-sight.left_head_proud":0.058,"daniel-defense-fixed-rear-sight.length":1.38,"daniel-defense-fixed-rear-sight.pocket_depth":0.42,"daniel-defense-fixed-rear-sight.pocket_length":0.627,"daniel-defense-fixed-rear-sight.pocket_width":0.467,"daniel-defense-fixed-rear-sight.screw_behind_front":0.293,"daniel-defense-fixed-rear-sight.screw_below_rail":0.015,"daniel-defense-fixed-rear-sight.screw_d":0.19,"daniel-defense-fixed-rear-sight.screw_head_d":0.36,"daniel-defense-fixed-rear-sight.screw_head_proud":0.036,"daniel-defense-fixed-rear-sight.sight_line_above_rail":1.363,"daniel-defense-fixed-rear-sight.slit_width":0.059,"daniel-defense-fixed-rear-sight.window_height":0.486,"daniel-defense-fixed-rear-sight.window_width":0.691,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{"side":[[-1.38,0.214],[-1.375,0.209],[-1.332,0.211],[-1.259,0.198],[-1.162,0.155],[-1.121,0.128],[-1.069,0.077],[-1.013,0],[-0.005,0],[0,0.004],[0,1.557],[-0.013,1.605],[-0.041,1.657],[-0.08,1.696],[-0.136,1.727],[-0.559,1.803],[-0.623,1.806],[-0.673,1.804],[-0.737,1.787],[-0.787,1.769],[-0.846,1.736],[-0.904,1.687],[-1.108,1.482],[-1.149,1.42],[-1.164,1.359],[-1.163,1.248],[-1.171,1.212],[-1.176,1.114],[-1.196,0.995],[-1.217,0.924],[-1.216,0.907],[-1.223,0.897],[-1.272,0.732],[-1.352,0.547],[-1.377,0.446]],"rear":[[-0.628,0.28],[-0.628,0.132],[-0.601,0.062],[-0.57,0.024],[-0.527,0],[-0.489,0],[-0.488,0.228],[0.49,0.228],[0.49,0],[0.522,0],[0.575,0.024],[0.605,0.062],[0.621,0.097],[0.628,0.132],[0.628,0.28],[0.607,0.369],[0.568,0.415],[0.49,0.459],[0.442,0.505],[0.42,0.549],[0.408,0.594],[0.406,1.806],[0.303,1.806],[0.303,1.451],[0.296,1.415],[0.28,1.381],[0.255,1.362],[0.222,1.352],[-0.22,1.352],[-0.249,1.359],[-0.276,1.379],[-0.296,1.415],[-0.303,1.451],[-0.303,1.806],[-0.403,1.806],[-0.408,0.593],[-0.418,0.549],[-0.44,0.504],[-0.49,0.459],[-0.568,0.415],[-0.608,0.369]],"plan":[[-1.38,0.406],[-1.38,-0.398],[-0.524,-0.628],[-0.133,-0.628],[0,-0.553],[0,0],[0,0.412],[0,0.554],[-0.074,0.628],[-0.244,0.628],[-0.495,0.628]]},"features":{"side":{"drum":[[[-0.972,1.662],[-0.191,1.662],[-0.191,0.882],[-0.972,0.882]]],"hub":[[[-0.718,1.408],[-0.446,1.408],[-0.446,1.137],[-0.718,1.137]]],"screw_head":[[[-0.484,0.408],[-0.102,0.408],[-0.102,0.023],[-0.484,0.023]]]},"rear":{"window":[[[-0.344,0.86],[0.346,0.86],[0.346,0.375],[-0.344,0.375]]],"split":[[[-0.028,0.375],[0.031,0.375],[0.031,0.228],[-0.028,0.228]]],"ceiling":[[[-0.314,0.228],[0.341,0.228],[0.341,0.228],[-0.314,0.228]]],"aperture_leg":[[[-0.181,1.773],[0.18,1.773],[0.18,1.323],[-0.181,1.323]]],"aperture_hole":[[[-0.093,1.686],[0.102,1.686],[0.102,1.491],[-0.093,1.491]]],"walls":[[[-0.403,1.806],[-0.303,1.806],[-0.303,1.353],[-0.403,1.353]],[[0.303,1.806],[0.406,1.806],[0.406,1.353],[0.303,1.353]]],"drum":[[[0.406,1.653],[0.449,1.653],[0.449,0.894],[0.406,0.894]]],"hub":[[[0.449,1.409],[0.625,1.409],[0.625,1.136],[0.449,1.136]]],"left_head":[[[-0.461,1.407],[-0.403,1.407],[-0.403,1.145],[-0.461,1.145]]],"screw_head":[[[0.627,0.405],[0.662,0.405],[0.662,0.084],[0.627,0.084]]]},"plan":{}},"placement":{"side":{"plane":"xy","offset":{"x":"front_x","y":"clamp_bottom_y"}},"rear":{"plane":"zy","offset":{"y":"clamp_bottom_y"}},"plan":{"plane":"xz","offset":{"x":"front_x"}}},"bounds":{"min":[-0.69,-0.228,-0.63],"max":[0.69,1.578,0.664]},"volume_in3":0.9711,"centroid":[0.1017,0.5519,0.0138],"shell":[0.1047,0.5747,0.0316],"area_in2":16.7861,"triangles":7408,"manifold":true,"rail_seat":{"x":[-0.69,0.69],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.537},"slabs":[[-0.69,-0.228,-0.63,0.69,0.494,0.664],[-0.586,0.494,-0.407,0.69,0.856,0.449],[-0.491,0.856,-0.461,0.69,1.217,0.626],[-0.443,1.217,-0.461,0.69,1.578,0.449]],"slots":["body","hardware","insert"]},"dead-air-rxd22ti":{"part":"dead-air-rxd22ti","model":"dead-air-rxd22ti.glb","script":"dead_air_rxd22ti.py","inputs":{"dead-air-rxd22ti.band_d":1.117,"dead-air-rxd22ti.band_end_x":0.55,"dead-air-rxd22ti.band_x":0.171,"dead-air-rxd22ti.core_face_inset":0.1,"dead-air-rxd22ti.exit_bore_d":0.26,"dead-air-rxd22ti.flange_chamfer_x":0.05,"dead-air-rxd22ti.flange_d":1.023,"dead-air-rxd22ti.flange_end_x":0.121,"dead-air-rxd22ti.flange_flats":0.924,"dead-air-rxd22ti.flange_rear_d":0.902,"dead-air-rxd22ti.flute_depth":0.04,"dead-air-rxd22ti.flute_end_x":3.351,"dead-air-rxd22ti.flute_width":0.232,"dead-air-rxd22ti.flute_x":1.624,"dead-air-rxd22ti.flutes":8,"dead-air-rxd22ti.front_groove_depth":0.008,"dead-air-rxd22ti.front_groove_width":0.016,"dead-air-rxd22ti.front_groove_x":4.933,"dead-air-rxd22ti.groove_d":1.087,"dead-air-rxd22ti.hex_corner_d":1.074,"dead-air-rxd22ti.hex_end_x":1.045,"dead-air-rxd22ti.hex_flats":0.969,"dead-air-rxd22ti.hex_x":0.654,"dead-air-rxd22ti.length":5.403,"dead-air-rxd22ti.od":1.1,"dead-air-rxd22ti.ring_bore_d":0.85,"dead-air-rxd22ti.ring_front_round":0.02,"dead-air-rxd22ti.ring_notch_depth":0.05,"dead-air-rxd22ti.ring_notch_width":0.13,"dead-air-rxd22ti.ring_notches":6,"dead-air-rxd22ti.ring_od":1.109,"dead-air-rxd22ti.tube_front_x":5.3,"dead-air-rxd22ti.tube_x":1.191,"dead-air-xrf-brake.body_d":0.653,"dead-air-xrf-brake.collar_d":0.737,"dead-air-xrf-brake.collar_x":0.519,"dead-air-xrf-brake.groove_d":0.75,"dead-air-xrf-brake.lead_end_x":0.462,"dead-air-xrf-brake.length":1.16,"dead-air-xrf-brake.neck_d":0.71,"dead-air-xrf-brake.suppressor_seat_x":0.197,"dead-air-xrf-brake.taper_end_x":0.742,"dead-air-xrf-brake.taper_front_d":0.664,"dead-air-xrf-brake.taper_x":0.576,"dead-air-xrf-brake.thread_end_x":0.408,"dead-air-xrf-brake.thread_major_d":0.814,"dead-air-xrf-brake.thread_x":0.236},"profiles":{},"features":{},"placement":{},"bounds":{"min":[0,-0.5585,-0.5585],"max":[5.403,0.5585,0.5585]},"volume_in3":4.4098,"centroid":[2.8751,0,0],"shell":[2.6738,0,0],"area_in2":55.8103,"triangles":13270,"manifold":true,"slabs":[[0,-0.558,-0.558,5.403,0.558,0.558]],"slots":["body","core"]},"dead-air-xrf-brake":{"part":"dead-air-xrf-brake","model":"dead-air-xrf-brake.glb","script":"dead_air_xrf_brake.py","inputs":{"dead-air-xrf-brake.barrel_thread_major_d":0.4957,"dead-air-xrf-brake.body_d":0.653,"dead-air-xrf-brake.bore_d":0.26,"dead-air-xrf-brake.chamber_front_wall":0.08,"dead-air-xrf-brake.collar_d":0.737,"dead-air-xrf-brake.collar_x":0.519,"dead-air-xrf-brake.front_round":0.02,"dead-air-xrf-brake.groove_d":0.75,"dead-air-xrf-brake.hex_end_x":0.162,"dead-air-xrf-brake.hex_flats":0.75,"dead-air-xrf-brake.lead_end_x":0.462,"dead-air-xrf-brake.length":1.16,"dead-air-xrf-brake.neck_d":0.71,"dead-air-xrf-brake.od":0.81,"dead-air-xrf-brake.port_length":0.266,"dead-air-xrf-brake.port_width":0.178,"dead-air-xrf-brake.port_x":0.922,"dead-air-xrf-brake.suppressor_seat_x":0.197,"dead-air-xrf-brake.taper_end_x":0.742,"dead-air-xrf-brake.taper_front_d":0.664,"dead-air-xrf-brake.taper_x":0.576,"dead-air-xrf-brake.thread_end_x":0.408,"dead-air-xrf-brake.thread_major_d":0.814,"dead-air-xrf-brake.thread_pitch":0.0375,"dead-air-xrf-brake.thread_x":0.236},"profiles":{},"features":{},"placement":{},"bounds":{"min":[0,-0.407,-0.407],"max":[1.16,0.407,0.407]},"volume_in3":0.2491,"centroid":[0.5062,-0.0002,0],"shell":[0.5514,0.0005,0.0004],"area_in2":5.4541,"triangles":8276,"manifold":true,"slabs":[[0,-0.407,-0.407,0.773,0.407,0.407],[0.773,-0.326,-0.326,1.16,0.326,0.326]],"slots":["body"]},"eotech-exps3":{"part":"eotech-exps3","model":"eotech-exps3.glb","script":"eotech_exps3.py","inputs":{"eotech-exps3.cap_knurl_depth":0.02,"eotech-exps3.cap_knurl_teeth":41,"eotech-exps3.clamp_front":0.93,"eotech-exps3.clamp_rear":1.77,"eotech-exps3.front_window_thickness":0.12480314960629921,"eotech-exps3.hood_left_z":-1.173,"eotech-exps3.hood_thickness":0.103,"eotech-exps3.optical_axis_above_rail":1.859,"eotech-exps3.rear_window_thickness":0.1874015748031496,"eotech-exps3.side_rear_x":-1.938,"eotech-exps3.top_above_rail":2.65,"eotech-exps3.window_corner_r":0.18,"eotech-exps3.window_height":0.85,"eotech-exps3.window_width":1.2,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{"side":[[0,-2.466],[0.002,-2.574],[0.017,-2.633],[0.035,-2.647],[0.155,-2.657],[0.158,-2.849],[0.176,-2.869],[2.095,-2.883],[2.217,-2.895],[2.294,-2.919],[2.688,-2.905],[2.841,-2.859],[2.847,-2.409],[2.845,-2.354],[2.826,-2.294],[2.833,-2.213],[2.823,-2.189],[2.829,-2.183],[2.887,-2.235],[2.949,-2.276],[3.097,-2.331],[3.305,-2.336],[3.408,-2.312],[3.477,-2.281],[3.559,-2.228],[3.672,-2.11],[3.739,-1.983],[3.775,-1.809],[3.749,-1.62],[3.694,-1.495],[3.592,-1.377],[3.467,-1.287],[3.475,-1.279],[3.496,-1.296],[3.492,-1.284],[3.382,-1.212],[3.281,-1.181],[3.152,-1.171],[3.143,-1.16],[3.006,-1.16],[2.99,-1.167],[2.345,-1.154],[2.345,-1.001],[2.3,-0.893],[2.271,-0.795],[2.161,-0.152],[2.147,-0.099],[2.13,-0.092],[2.115,0],[0.568,-0.01],[0.519,-0.042],[0.5,-0.147],[0.538,-0.326],[0.545,-0.491],[0.531,-0.613],[0.509,-0.699],[0.464,-0.814],[0.414,-0.903],[0.351,-0.981],[0.17,-1.149],[0.134,-1.204],[0.11,-1.283],[0.043,-1.629],[0.029,-1.746],[0.029,-2.347],[0.007,-2.394]],"right":[[0,-2.643],[0.005,-2.696],[0.019,-2.733],[0.158,-2.745],[0.16,-2.841],[0.172,-2.873],[1.035,-2.866],[1.058,-2.799],[1.067,-2.857],[1.084,-2.873],[1.127,-2.891],[1.252,-2.909],[1.468,-2.911],[2.579,-2.904],[2.717,-2.896],[2.818,-2.876],[2.844,-2.863],[2.866,-2.836],[2.863,-2.413],[2.843,-2.347],[2.855,-2.319],[2.848,-2.273],[2.857,-2.267],[2.936,-2.328],[3.004,-2.364],[3.111,-2.397],[3.346,-2.397],[3.473,-2.354],[3.603,-2.267],[3.709,-2.141],[3.747,-2.067],[3.772,-1.988],[3.785,-1.835],[3.757,-1.675],[3.693,-1.537],[3.632,-1.461],[3.637,-1.456],[3.627,-1.438],[3.525,-1.275],[3.481,-1.228],[3.402,-1.172],[3.323,-1.136],[3.231,-1.116],[2.918,-1.103],[2.811,-1.049],[2.717,-1.032],[2.615,-1.039],[2.526,-1.07],[2.508,-1.039],[2.495,-1.057],[2.419,-1.098],[2.392,-1.084],[2.295,-0.911],[2.254,-0.801],[2.224,-0.666],[2.142,-0.172],[2.129,-0.157],[2.109,-0.011],[2.092,0],[0.562,-0.02],[0.525,-0.042],[0.487,-0.113],[0.474,-0.21],[0.479,-0.274],[0.517,-0.424],[0.53,-0.569],[0.522,-0.692],[0.497,-0.809],[0.443,-0.941],[0.352,-1.028],[0.321,-1.081],[0.303,-1.142],[0.168,-1.275],[0.125,-1.374],[0.064,-1.708],[0.043,-1.907],[0.056,-2.421],[0.022,-2.433],[0.008,-2.457]],"top":[[0,1.919],[0,1.644],[0.018,1.626],[0.065,1.622],[0.058,0.784],[0.047,0.773],[0.011,0.773],[0,0.762],[0,0.473],[0.058,0.459],[0.061,0.34],[0.166,0.322],[0.163,0.311],[0.137,0.307],[0.116,0.257],[0.116,0.17],[0.126,0.152],[0.152,0.141],[0.09,0.137],[0.072,0.126],[0.065,0.112],[0.065,0.025],[0.076,0.014],[0.126,0.014],[0.134,0.007],[0.871,0.007],[0.878,0],[2.735,0.007],[2.753,0.033],[2.753,0.098],[2.742,0.116],[2.692,0.116],[2.681,0.126],[2.681,0.177],[2.699,0.181],[2.717,0.199],[2.724,0.235],[2.75,0.275],[2.901,0.188],[2.981,0.159],[3.031,0.159],[3.039,0.152],[3.667,0.152],[3.674,0.159],[3.776,0.159],[3.801,0.191],[3.808,1.832],[3.815,1.839],[3.808,2.02],[3.797,2.031],[3.667,2.031],[3.653,2.052],[3.635,2.056],[3.653,2.074],[3.689,2.074],[3.7,2.085],[3.7,2.265],[3.689,2.276],[3.674,2.283],[3.306,2.283],[3.302,2.229],[3.241,2.218],[3.237,2.273],[3.226,2.283],[2.952,2.283],[2.945,2.291],[2.858,2.291],[2.833,2.265],[2.833,2.085],[2.883,2.078],[2.872,2.059],[2.829,2.052],[2.663,2.059],[2.656,2.067],[2.612,2.067],[2.601,2.078],[2.605,2.088],[2.627,2.096],[2.728,2.103],[2.76,2.121],[2.768,2.2],[2.75,2.24],[2.294,2.24],[2.287,2.247],[2.121,2.247],[2.092,2.262],[1.832,2.262],[1.803,2.247],[0.09,2.247],[0.072,2.229],[0.072,2.128],[0.083,2.11],[0.159,2.078],[0.152,1.962],[0.166,1.947],[0.033,1.937]],"front":[[0,-2.229],[0.007,-2.579],[0.012,-2.6],[0.04,-2.616],[0.038,-2.886],[0.057,-2.908],[0.116,-2.913],[0.171,-2.898],[0.211,-2.757],[0.233,-2.742],[0.32,-2.733],[0.349,-2.816],[0.409,-2.862],[0.437,-2.869],[0.634,-2.869],[0.667,-2.859],[0.69,-2.837],[0.71,-2.761],[0.808,-2.761],[0.854,-2.743],[0.854,-2.635],[0.864,-2.599],[0.907,-2.589],[1.176,-2.578],[1.514,-2.594],[1.561,-2.627],[1.614,-2.682],[1.656,-2.745],[1.677,-2.83],[1.699,-2.855],[1.756,-2.866],[1.981,-2.862],[2.028,-2.84],[2.059,-2.806],[2.076,-2.769],[2.09,-2.68],[2.113,-2.645],[2.185,-2.594],[2.229,-2.601],[2.245,-2.593],[2.252,-2.466],[2.242,-2.056],[2.186,-1.226],[2.144,-0.841],[2.116,-0.393],[2.078,-0.264],[2.036,-0.194],[1.969,-0.124],[1.915,-0.087],[1.819,-0.047],[1.659,-0.023],[1.432,-0.005],[1.066,0],[0.728,-0.021],[0.503,-0.056],[0.43,-0.087],[0.367,-0.129],[0.298,-0.201],[0.263,-0.257],[0.235,-0.327],[0.218,-0.416],[0.211,-0.754],[0.197,-0.939],[0.181,-0.972],[0.07,-1.075],[0.033,-1.146],[0.021,-1.2],[0.002,-1.817]]},"features":{"side":{"nv_boss":[[[0.675,-1.18],[0.221,-1.18],[0.221,-1.634],[0.675,-1.634]]],"nv_button":[[[0.563,-1.292],[0.334,-1.292],[0.334,-1.522],[0.563,-1.522]]],"button_pad":[[[1.173,-1.833],[0.145,-1.833],[0.145,-2.366],[1.173,-2.366]]],"buttons":[[[1.034,-1.964],[0.735,-1.964],[0.735,-2.256],[1.034,-2.256]],[[0.556,-1.964],[0.25,-1.964],[0.25,-2.256],[0.556,-2.256]]],"screws":[[[2.497,-2.155],[2.335,-2.155],[2.335,-2.318],[2.497,-2.318]],[[1.522,-2.155],[1.359,-2.155],[1.359,-2.318],[1.522,-2.318]]],"lever":[[[2.698,-2.488],[2.27,-2.488],[2.27,-2.806],[2.698,-2.806]]],"cam":[[[2.134,-2.442],[1.775,-2.442],[1.775,-2.7],[2.134,-2.7]]],"plate_front":[[[2.368,-1.189],[2.421,-1.295],[2.516,-1.414],[2.6,-1.534],[2.66,-1.653],[2.696,-1.773],[2.708,-1.964],[2.708,-2.299],[3.186,-2.299],[3.186,-1.189]]]},"right":{"elevation":[[[0.59,-1.198],[1.415,-1.198],[1.415,-2.024],[0.59,-2.024]]],"elevation_dial":[[[0.814,-1.397],[1.201,-1.397],[1.201,-1.784],[0.814,-1.784]]],"elevation_slot":[[[0.936,-1.417],[1.02,-1.415],[1.053,-1.777],[0.977,-1.782]]],"windage":[[[1.759,-1.514],[2.599,-1.514],[2.599,-2.355],[1.759,-2.355]]],"windage_dial":[[[2.001,-1.698],[2.396,-1.698],[2.396,-2.095],[2.001,-2.095]]],"windage_slot":[[[2.036,-1.973],[2.332,-1.797],[2.37,-1.843],[2.077,-2.024]]],"cap":[[[2.824,-1.463],[3.69,-1.463],[3.69,-2.329],[2.824,-2.329]]],"cap_slot":[[[3.432,-1.527],[3.534,-1.586],[3.081,-2.278],[2.994,-2.233]]],"nut":[[[1.772,-2.515],[2.103,-2.515],[2.103,-2.846],[1.772,-2.846]]],"screw":[[[0.197,-2.253],[0.416,-2.253],[0.416,-2.472],[0.197,-2.472]]],"plate_front":[[[2.337,-1.119],[2.408,-1.26],[2.472,-1.361],[2.536,-1.463],[2.612,-1.565],[2.676,-1.667],[2.714,-1.769],[2.734,-1.871],[2.739,-2.075],[2.734,-2.393],[3.274,-2.393],[3.274,-1.119]]],"base":[[[0.167,-2.457],[2.867,-2.457],[2.867,-2.91],[0.167,-2.91]]]},"top":{"cap":[[[2.843,2.049],[3.696,2.049],[3.696,2.294],[2.843,2.294]]],"hood_top":[[[0.524,0.199],[2.244,0.199],[2.244,2.171],[0.524,2.171]]]},"front":{"hood_gap":[[[0.225,-1.097],[0.235,-1.061],[0.347,-0.932],[0.371,-0.871],[0.385,-0.374],[0.403,-0.313],[0.434,-0.262],[0.527,-0.181],[0.618,-0.145],[0.921,-0.12],[0.925,-0.11],[0.963,-0.12],[0.986,-0.108],[1.005,-0.117],[1.031,-0.106],[1.387,-0.108],[1.394,-0.117],[1.434,-0.113],[1.469,-0.127],[1.507,-0.12],[1.526,-0.129],[1.549,-0.124],[1.678,-0.138],[1.749,-0.157],[1.838,-0.213],[1.893,-0.28],[1.928,-0.386],[1.954,-0.892],[1.946,-0.934],[1.937,-0.925],[1.926,-0.803],[1.909,-0.487],[1.893,-0.428],[1.853,-0.346],[1.858,-0.341],[1.791,-0.274],[1.746,-0.244],[1.678,-0.216],[1.57,-0.199],[1.355,-0.185],[1.094,-0.183],[0.7,-0.206],[0.595,-0.246],[0.529,-0.293],[0.488,-0.339],[0.45,-0.405],[0.425,-0.482],[0.422,-0.62],[0.394,-1.017],[0.382,-1.066],[0.389,-1.073],[0.385,-1.127],[0.32,-1.135],[0.299,-1.149],[0.233,-1.149]]],"latch":[[[0.041,-2.605],[0.196,-2.605],[0.196,-2.912],[0.041,-2.912]]],"cover":[[[0.341,-1.392],[1.915,-1.392],[1.915,-2.577],[0.341,-2.577]]],"cover_screws":[[[0.529,-1.479],[0.67,-1.479],[0.67,-1.62],[0.529,-1.62]],[[1.678,-1.465],[1.819,-1.465],[1.819,-1.606],[1.678,-1.606]],[[0.508,-2.581],[0.649,-2.581],[0.649,-2.722],[0.508,-2.722]],[[1.692,-2.581],[1.833,-2.581],[1.833,-2.722],[1.692,-2.722]]]}},"placement":{"side":{"plane":"xy","offset":{"x":"side_rear_x","y":"top_above_rail"}},"right":{"plane":"xy","offset":{"x":"side_rear_x","y":"top_above_rail"}},"top":{"plane":"xz","offset":{"x":"side_rear_x","y":"hood_left_z"}},"front":{"plane":"zy","offset":{"x":"hood_left_z","y":"top_above_rail"}}},"bounds":{"min":[-1.938,-0.263,-1.2445],"max":[1.837,2.65,1.121]},"axis_y":1.859,"volume_in3":12.9823,"centroid":[-0.2683,0.9147,-0.053],"shell":[-0.4761,1.0518,-0.0799],"area_in2":97.4549,"triangles":6430,"manifold":true,"slabs":[[-1.938,-0.22,-1.244,-1.56,1.702,1.102],[-1.56,-0.231,-1.244,-0.05,2.649,1.102],[-0.05,-0.26,-1.169,0.327,2.65,1.079],[0.327,-0.263,-1.199,0.705,1.89,1.074],[0.705,-0.257,-1.166,1.082,1.49,1.121],[1.082,0.314,-1.021,1.46,1.49,1.121],[1.46,0.336,-1.021,1.837,1.428,1.121]],"slots":["body","housing","clamp","cover","buttons","hardware","lens"]},"eotech-g33.aside":{"part":"eotech-g33","component":"aside","model":"eotech-g33.aside.glb","script":"eotech_g33.py","inputs":{"eotech-g33.axis_above_clamp_bottom":2.22,"eotech-g33.base_left_of_centre":1,"eotech-g33.base_top_above_clamp_bottom":0.555,"eotech-g33.body_height":1.627,"eotech-g33.clamp_bottom_y":-0.37,"eotech-g33.clamp_length":1.395,"eotech-g33.clamp_nut_above_clamp_bottom":0.32,"eotech-g33.clamp_nut_d":0.36,"eotech-g33.diopter_flute_angle":11,"eotech-g33.diopter_flute_depth":0.028,"eotech-g33.diopter_flutes":18,"eotech-g33.eyepiece_glass_d":0.95,"eotech-g33.eyepiece_rear_behind_base":3.168,"eotech-g33.eyepiece_ring_od":1.369,"eotech-g33.flip_angle":93.5,"eotech-g33.height":3.354,"eotech-g33.hinge_axis_above_clamp_bottom":0.871,"eotech-g33.hinge_axis_right_of_centre":0.69,"eotech-g33.hinge_barrel_d":0.5,"eotech-g33.hinge_block_length":1.394,"eotech-g33.hinge_knuckle_d":0.62,"eotech-g33.hinge_knuckle_length":0.37,"eotech-g33.hinge_pin_d":0.316,"eotech-g33.hinge_web_inner_right_of_centre":0.13,"eotech-g33.knob_lugs":8,"eotech-g33.knob_notch_angle":24,"eotech-g33.knob_notch_depth":0.036,"eotech-g33.knob_notch_phase":35,"eotech-g33.length":4.015748031496063,"eotech-g33.lever_tail_behind_base":1.381,"eotech-g33.lever_thickness":0.2,"eotech-g33.objective_glass_d":0.8976377952755906,"eotech-g33.objective_tube_od":1.149,"eotech-g33.optical_axis_above_rail_no_spacer":1.574803149606299,"eotech-g33.optical_axis_above_rail_spacer":1.8503937007874016,"eotech-g33.plate_bottom_above_clamp_bottom":0.866,"eotech-g33.plate_top_above_clamp_bottom":1.1,"eotech-g33.plate_width":0.64,"eotech-g33.riser_length":1.608,"eotech-g33.riser_thickness":0.2755905511811024,"eotech-g33.riser_top_above_clamp_bottom":1.385,"eotech-g33.riser_width":0.75,"eotech-g33.side_knob_reach":1.11,"eotech-g33.sts_mount_height":1.1811023622047243,"eotech-g33.sts_mount_length":1.6614173228346458,"eotech-g33.top_knob_behind_base":0.769,"eotech-g33.top_knob_d":0.7,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{"side":[[-3.176,2.432],[-3.176,1.993],[-3.163,1.714],[-3.142,1.596],[-3.099,1.546],[-2.779,1.539],[-2.739,1.579],[-2.726,1.609],[-2.699,1.614],[-2.667,1.455],[-2.632,1.43],[-2.542,1.43],[-2.404,1.413],[-1.611,1.396],[-1.434,1.405],[-1.141,1.384],[-0.801,1.385],[-0.801,1.111],[-0.824,1.107],[-0.832,1.092],[-0.832,0.878],[-0.812,0.865],[-0.677,0.861],[-0.68,0.6],[-0.698,0.569],[-1.369,0.555],[-1.382,0.534],[-1.385,0.413],[-1.385,0.103],[-1.374,0.087],[-1.083,0.082],[-0.705,0.097],[-0.7,0.01],[-0.15,0],[0,0.002],[0.603,0],[0.683,0.002],[0.694,0.011],[0.699,0.571],[0.689,0.583],[0.689,0.859],[0.824,0.86],[0.832,0.869],[0.832,1.101],[0.811,1.121],[0.82,2.386],[0.811,2.8],[-0.281,2.806],[-0.304,2.928],[-0.383,3.007],[-0.437,3.02],[-0.423,3.037],[-0.42,3.071],[-0.452,3.103],[-0.452,3.139],[-0.42,3.163],[-0.42,3.207],[-0.485,3.264],[-0.516,3.269],[-0.552,3.312],[-0.601,3.349],[-0.647,3.358],[-0.657,3.327],[-0.703,3.361],[-0.841,3.361],[-0.884,3.322],[-0.889,3.358],[-0.926,3.358],[-0.991,3.312],[-1.03,3.271],[-1.052,3.266],[-1.107,3.223],[-1.121,3.207],[-1.121,3.166],[-1.087,3.142],[-1.087,3.127],[-1.094,3.096],[-1.121,3.076],[-1.112,3.024],[-1.531,3.036],[-2.622,3.024],[-2.653,3.01],[-2.667,2.987],[-2.695,2.84],[-2.724,2.842],[-2.749,2.885],[-2.782,2.913],[-3.051,2.915],[-3.094,2.908],[-3.134,2.868],[-3.154,2.793]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"y":"clamp_bottom_y"}}},"bounds":{"min":[-3.176,-0.37,-1],"max":[0.8307,1.9357,3.2189]},"axis_y":1.1073,"axis_z":2.079,"volume_in3":9.6454,"centroid":[-0.9738,0.9265,1.671],"shell":[-0.7997,0.8351,1.4456],"area_in2":58.8957,"triangles":15526,"manifold":true,"rail_seat":{"x":[-0.6975,0.6975],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-1.385,-0.37,-1,0.699,0.185,-0.616],[-0.697,-0.37,-0.616,0.697,0.185,-0.233],[-0.697,0,-0.233,0.697,0.492,0.151],[-0.709,-0.37,0.151,0.709,0.769,0.534],[-0.831,-0.37,0.534,0.831,1.509,0.918],[-2.667,-0.37,0.918,0.831,1.55,1.301],[-3.18,0.156,1.301,0.823,1.847,1.685],[-3.18,-0.005,1.685,0.823,1.936,2.452],[-3.18,0.348,2.452,0.823,1.87,2.835],[-2.667,0.698,2.835,-0.35,1.483,3.219]],"slots":["body","tube","mount","hardware","pin","lens"]},"eotech-g33.aside_no_riser":{"part":"eotech-g33","component":"aside_no_riser","model":"eotech-g33.aside_no_riser.glb","script":"eotech_g33.py","inputs":{"eotech-g33.axis_above_clamp_bottom":2.22,"eotech-g33.base_left_of_centre":1,"eotech-g33.base_top_above_clamp_bottom":0.555,"eotech-g33.body_height":1.627,"eotech-g33.clamp_bottom_y":-0.37,"eotech-g33.clamp_length":1.395,"eotech-g33.clamp_nut_above_clamp_bottom":0.32,"eotech-g33.clamp_nut_d":0.36,"eotech-g33.diopter_flute_angle":11,"eotech-g33.diopter_flute_depth":0.028,"eotech-g33.diopter_flutes":18,"eotech-g33.eyepiece_glass_d":0.95,"eotech-g33.eyepiece_rear_behind_base":3.168,"eotech-g33.eyepiece_ring_od":1.369,"eotech-g33.flip_angle":93.5,"eotech-g33.height":3.354,"eotech-g33.hinge_axis_above_clamp_bottom":0.871,"eotech-g33.hinge_axis_right_of_centre":0.69,"eotech-g33.hinge_barrel_d":0.5,"eotech-g33.hinge_block_length":1.394,"eotech-g33.hinge_knuckle_d":0.62,"eotech-g33.hinge_knuckle_length":0.37,"eotech-g33.hinge_pin_d":0.316,"eotech-g33.hinge_web_inner_right_of_centre":0.13,"eotech-g33.knob_lugs":8,"eotech-g33.knob_notch_angle":24,"eotech-g33.knob_notch_depth":0.036,"eotech-g33.knob_notch_phase":35,"eotech-g33.length":4.015748031496063,"eotech-g33.lever_tail_behind_base":1.381,"eotech-g33.lever_thickness":0.2,"eotech-g33.objective_glass_d":0.8976377952755906,"eotech-g33.objective_tube_od":1.149,"eotech-g33.optical_axis_above_rail_no_spacer":1.574803149606299,"eotech-g33.optical_axis_above_rail_spacer":1.8503937007874016,"eotech-g33.plate_bottom_above_clamp_bottom":0.866,"eotech-g33.plate_top_above_clamp_bottom":1.1,"eotech-g33.plate_width":0.64,"eotech-g33.riser_length":1.608,"eotech-g33.riser_thickness":0.2755905511811024,"eotech-g33.riser_top_above_clamp_bottom":1.385,"eotech-g33.riser_width":0.75,"eotech-g33.side_knob_reach":1.11,"eotech-g33.sts_mount_height":1.1811023622047243,"eotech-g33.sts_mount_length":1.6614173228346458,"eotech-g33.top_knob_behind_base":0.769,"eotech-g33.top_knob_d":0.7,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{"side":[[-3.176,2.432],[-3.176,1.993],[-3.163,1.714],[-3.142,1.596],[-3.099,1.546],[-2.779,1.539],[-2.739,1.579],[-2.726,1.609],[-2.699,1.614],[-2.667,1.455],[-2.632,1.43],[-2.542,1.43],[-2.404,1.413],[-1.611,1.396],[-1.434,1.405],[-1.141,1.384],[-0.801,1.385],[-0.801,1.111],[-0.824,1.107],[-0.832,1.092],[-0.832,0.878],[-0.812,0.865],[-0.677,0.861],[-0.68,0.6],[-0.698,0.569],[-1.369,0.555],[-1.382,0.534],[-1.385,0.413],[-1.385,0.103],[-1.374,0.087],[-1.083,0.082],[-0.705,0.097],[-0.7,0.01],[-0.15,0],[0,0.002],[0.603,0],[0.683,0.002],[0.694,0.011],[0.699,0.571],[0.689,0.583],[0.689,0.859],[0.824,0.86],[0.832,0.869],[0.832,1.101],[0.811,1.121],[0.82,2.386],[0.811,2.8],[-0.281,2.806],[-0.304,2.928],[-0.383,3.007],[-0.437,3.02],[-0.423,3.037],[-0.42,3.071],[-0.452,3.103],[-0.452,3.139],[-0.42,3.163],[-0.42,3.207],[-0.485,3.264],[-0.516,3.269],[-0.552,3.312],[-0.601,3.349],[-0.647,3.358],[-0.657,3.327],[-0.703,3.361],[-0.841,3.361],[-0.884,3.322],[-0.889,3.358],[-0.926,3.358],[-0.991,3.312],[-1.03,3.271],[-1.052,3.266],[-1.107,3.223],[-1.121,3.207],[-1.121,3.166],[-1.087,3.142],[-1.087,3.127],[-1.094,3.096],[-1.121,3.076],[-1.112,3.024],[-1.531,3.036],[-2.622,3.024],[-2.653,3.01],[-2.667,2.987],[-2.695,2.84],[-2.724,2.842],[-2.749,2.885],[-2.782,2.913],[-3.051,2.915],[-3.094,2.908],[-3.134,2.868],[-3.154,2.793]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"y":"clamp_bottom_y"}}},"bounds":{"min":[-3.176,-0.37,-1],"max":[0.8307,1.9526,2.9438]},"axis_y":1.1242,"axis_z":1.8039,"volume_in3":9.3178,"centroid":[-1.008,0.9314,1.4725],"shell":[-0.8532,0.824,1.2866],"area_in2":55.211,"triangles":15514,"manifold":true,"rail_seat":{"x":[-0.6975,0.6975],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-3.18,0.43,1.109,-2.815,1.818,2.498],[-2.815,0.298,0.978,-1.722,1.95,2.63],[-1.722,-0.283,-1,-1.357,1.953,2.632],[-1.357,-0.288,-1,-0.992,1.947,2.889],[-0.992,-0.37,-1,-0.263,1.941,2.944],[-0.263,-0.37,-1,0.831,1.71,2.389]],"slots":["body","tube","mount","hardware","pin","lens"]},"eotech-g33.inline":{"part":"eotech-g33","component":"inline","model":"eotech-g33.inline.glb","script":"eotech_g33.py","inputs":{"eotech-g33.axis_above_clamp_bottom":2.22,"eotech-g33.base_left_of_centre":1,"eotech-g33.base_top_above_clamp_bottom":0.555,"eotech-g33.body_height":1.627,"eotech-g33.clamp_bottom_y":-0.37,"eotech-g33.clamp_length":1.395,"eotech-g33.clamp_nut_above_clamp_bottom":0.32,"eotech-g33.clamp_nut_d":0.36,"eotech-g33.diopter_flute_angle":11,"eotech-g33.diopter_flute_depth":0.028,"eotech-g33.diopter_flutes":18,"eotech-g33.eyepiece_glass_d":0.95,"eotech-g33.eyepiece_rear_behind_base":3.168,"eotech-g33.eyepiece_ring_od":1.369,"eotech-g33.flip_angle":93.5,"eotech-g33.height":3.354,"eotech-g33.hinge_axis_above_clamp_bottom":0.871,"eotech-g33.hinge_axis_right_of_centre":0.69,"eotech-g33.hinge_barrel_d":0.5,"eotech-g33.hinge_block_length":1.394,"eotech-g33.hinge_knuckle_d":0.62,"eotech-g33.hinge_knuckle_length":0.37,"eotech-g33.hinge_pin_d":0.316,"eotech-g33.hinge_web_inner_right_of_centre":0.13,"eotech-g33.knob_lugs":8,"eotech-g33.knob_notch_angle":24,"eotech-g33.knob_notch_depth":0.036,"eotech-g33.knob_notch_phase":35,"eotech-g33.length":4.015748031496063,"eotech-g33.lever_tail_behind_base":1.381,"eotech-g33.lever_thickness":0.2,"eotech-g33.objective_glass_d":0.8976377952755906,"eotech-g33.objective_tube_od":1.149,"eotech-g33.optical_axis_above_rail_no_spacer":1.574803149606299,"eotech-g33.optical_axis_above_rail_spacer":1.8503937007874016,"eotech-g33.plate_bottom_above_clamp_bottom":0.866,"eotech-g33.plate_top_above_clamp_bottom":1.1,"eotech-g33.plate_width":0.64,"eotech-g33.riser_length":1.608,"eotech-g33.riser_thickness":0.2755905511811024,"eotech-g33.riser_top_above_clamp_bottom":1.385,"eotech-g33.riser_width":0.75,"eotech-g33.side_knob_reach":1.11,"eotech-g33.sts_mount_height":1.1811023622047243,"eotech-g33.sts_mount_length":1.6614173228346458,"eotech-g33.top_knob_behind_base":0.769,"eotech-g33.top_knob_d":0.7,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{"side":[[-3.176,2.432],[-3.176,1.993],[-3.163,1.714],[-3.142,1.596],[-3.099,1.546],[-2.779,1.539],[-2.739,1.579],[-2.726,1.609],[-2.699,1.614],[-2.667,1.455],[-2.632,1.43],[-2.542,1.43],[-2.404,1.413],[-1.611,1.396],[-1.434,1.405],[-1.141,1.384],[-0.801,1.385],[-0.801,1.111],[-0.824,1.107],[-0.832,1.092],[-0.832,0.878],[-0.812,0.865],[-0.677,0.861],[-0.68,0.6],[-0.698,0.569],[-1.369,0.555],[-1.382,0.534],[-1.385,0.413],[-1.385,0.103],[-1.374,0.087],[-1.083,0.082],[-0.705,0.097],[-0.7,0.01],[-0.15,0],[0,0.002],[0.603,0],[0.683,0.002],[0.694,0.011],[0.699,0.571],[0.689,0.583],[0.689,0.859],[0.824,0.86],[0.832,0.869],[0.832,1.101],[0.811,1.121],[0.82,2.386],[0.811,2.8],[-0.281,2.806],[-0.304,2.928],[-0.383,3.007],[-0.437,3.02],[-0.423,3.037],[-0.42,3.071],[-0.452,3.103],[-0.452,3.139],[-0.42,3.163],[-0.42,3.207],[-0.485,3.264],[-0.516,3.269],[-0.552,3.312],[-0.601,3.349],[-0.647,3.358],[-0.657,3.327],[-0.703,3.361],[-0.841,3.361],[-0.884,3.322],[-0.889,3.358],[-0.926,3.358],[-0.991,3.312],[-1.03,3.271],[-1.052,3.266],[-1.107,3.223],[-1.121,3.207],[-1.121,3.166],[-1.087,3.142],[-1.087,3.127],[-1.094,3.096],[-1.121,3.076],[-1.112,3.024],[-1.531,3.036],[-2.622,3.024],[-2.653,3.01],[-2.667,2.987],[-2.695,2.84],[-2.724,2.842],[-2.749,2.885],[-2.782,2.913],[-3.051,2.915],[-3.094,2.908],[-3.134,2.868],[-3.154,2.793]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"y":"clamp_bottom_y"}}},"bounds":{"min":[-3.176,-0.37,-1],"max":[0.8307,2.988,1.11]},"axis_y":1.8504,"axis_z":0,"volume_in3":9.6454,"centroid":[-0.9738,1.4725,0.0351],"shell":[-0.7997,1.2696,0.0602],"area_in2":58.8957,"triangles":15526,"manifold":true,"rail_seat":{"x":[-0.6975,0.6975],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-3.18,1.156,-0.691,-2.815,2.545,0.691],[-2.815,1.037,-0.814,-1.722,2.664,0.814],[-1.722,-0.283,-1,-1.357,2.666,0.816],[-1.357,-0.288,-1,-0.992,2.937,1.059],[-0.992,-0.37,-1,-0.263,2.988,1.11],[-0.263,-0.37,-1,0.831,2.436,1.03]],"slots":["body","tube","mount","hardware","pin","lens"]},"eotech-g33.inline_no_riser":{"part":"eotech-g33","component":"inline_no_riser","model":"eotech-g33.inline_no_riser.glb","script":"eotech_g33.py","inputs":{"eotech-g33.axis_above_clamp_bottom":2.22,"eotech-g33.base_left_of_centre":1,"eotech-g33.base_top_above_clamp_bottom":0.555,"eotech-g33.body_height":1.627,"eotech-g33.clamp_bottom_y":-0.37,"eotech-g33.clamp_length":1.395,"eotech-g33.clamp_nut_above_clamp_bottom":0.32,"eotech-g33.clamp_nut_d":0.36,"eotech-g33.diopter_flute_angle":11,"eotech-g33.diopter_flute_depth":0.028,"eotech-g33.diopter_flutes":18,"eotech-g33.eyepiece_glass_d":0.95,"eotech-g33.eyepiece_rear_behind_base":3.168,"eotech-g33.eyepiece_ring_od":1.369,"eotech-g33.flip_angle":93.5,"eotech-g33.height":3.354,"eotech-g33.hinge_axis_above_clamp_bottom":0.871,"eotech-g33.hinge_axis_right_of_centre":0.69,"eotech-g33.hinge_barrel_d":0.5,"eotech-g33.hinge_block_length":1.394,"eotech-g33.hinge_knuckle_d":0.62,"eotech-g33.hinge_knuckle_length":0.37,"eotech-g33.hinge_pin_d":0.316,"eotech-g33.hinge_web_inner_right_of_centre":0.13,"eotech-g33.knob_lugs":8,"eotech-g33.knob_notch_angle":24,"eotech-g33.knob_notch_depth":0.036,"eotech-g33.knob_notch_phase":35,"eotech-g33.length":4.015748031496063,"eotech-g33.lever_tail_behind_base":1.381,"eotech-g33.lever_thickness":0.2,"eotech-g33.objective_glass_d":0.8976377952755906,"eotech-g33.objective_tube_od":1.149,"eotech-g33.optical_axis_above_rail_no_spacer":1.574803149606299,"eotech-g33.optical_axis_above_rail_spacer":1.8503937007874016,"eotech-g33.plate_bottom_above_clamp_bottom":0.866,"eotech-g33.plate_top_above_clamp_bottom":1.1,"eotech-g33.plate_width":0.64,"eotech-g33.riser_length":1.608,"eotech-g33.riser_thickness":0.2755905511811024,"eotech-g33.riser_top_above_clamp_bottom":1.385,"eotech-g33.riser_width":0.75,"eotech-g33.side_knob_reach":1.11,"eotech-g33.sts_mount_height":1.1811023622047243,"eotech-g33.sts_mount_length":1.6614173228346458,"eotech-g33.top_knob_behind_base":0.769,"eotech-g33.top_knob_d":0.7,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{"side":[[-3.176,2.432],[-3.176,1.993],[-3.163,1.714],[-3.142,1.596],[-3.099,1.546],[-2.779,1.539],[-2.739,1.579],[-2.726,1.609],[-2.699,1.614],[-2.667,1.455],[-2.632,1.43],[-2.542,1.43],[-2.404,1.413],[-1.611,1.396],[-1.434,1.405],[-1.141,1.384],[-0.801,1.385],[-0.801,1.111],[-0.824,1.107],[-0.832,1.092],[-0.832,0.878],[-0.812,0.865],[-0.677,0.861],[-0.68,0.6],[-0.698,0.569],[-1.369,0.555],[-1.382,0.534],[-1.385,0.413],[-1.385,0.103],[-1.374,0.087],[-1.083,0.082],[-0.705,0.097],[-0.7,0.01],[-0.15,0],[0,0.002],[0.603,0],[0.683,0.002],[0.694,0.011],[0.699,0.571],[0.689,0.583],[0.689,0.859],[0.824,0.86],[0.832,0.869],[0.832,1.101],[0.811,1.121],[0.82,2.386],[0.811,2.8],[-0.281,2.806],[-0.304,2.928],[-0.383,3.007],[-0.437,3.02],[-0.423,3.037],[-0.42,3.071],[-0.452,3.103],[-0.452,3.139],[-0.42,3.163],[-0.42,3.207],[-0.485,3.264],[-0.516,3.269],[-0.552,3.312],[-0.601,3.349],[-0.647,3.358],[-0.657,3.327],[-0.703,3.361],[-0.841,3.361],[-0.884,3.322],[-0.889,3.358],[-0.926,3.358],[-0.991,3.312],[-1.03,3.271],[-1.052,3.266],[-1.107,3.223],[-1.121,3.207],[-1.121,3.166],[-1.087,3.142],[-1.087,3.127],[-1.094,3.096],[-1.121,3.076],[-1.112,3.024],[-1.531,3.036],[-2.622,3.024],[-2.653,3.01],[-2.667,2.987],[-2.695,2.84],[-2.724,2.842],[-2.749,2.885],[-2.782,2.913],[-3.051,2.915],[-3.094,2.908],[-3.134,2.868],[-3.154,2.793]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"y":"clamp_bottom_y"}}},"bounds":{"min":[-3.176,-0.37,-1],"max":[0.8307,2.7124,1.11]},"axis_y":1.5748,"axis_z":0,"volume_in3":9.3178,"centroid":[-1.008,1.2747,0.0363],"shell":[-0.8532,1.1139,0.0642],"area_in2":55.211,"triangles":15514,"manifold":true,"rail_seat":{"x":[-0.6975,0.6975],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-3.18,0.88,-0.691,-2.815,2.269,0.691],[-2.815,0.761,-0.814,-1.722,2.388,0.814],[-1.722,-0.283,-1,-1.357,2.39,0.816],[-1.357,-0.288,-1,-0.992,2.662,1.059],[-0.992,-0.37,-1,-0.263,2.712,1.11],[-0.263,-0.37,-1,0.831,2.16,1.03]],"slots":["body","tube","mount","hardware","pin","lens"]},"eotech-g45.aside":{"part":"eotech-g45","component":"aside","model":"eotech-g45.aside.glb","script":"eotech_g45.py","inputs":{"eotech-g45.axis_above_clamp_bottom":2.196,"eotech-g45.base_left_of_centre":1,"eotech-g45.base_top_above_clamp_bottom":0.555,"eotech-g45.body_bottom_below_axis":0.82,"eotech-g45.body_half_width":0.8915,"eotech-g45.body_height":1.692,"eotech-g45.body_side_flat_bottom_below_axis":0.373,"eotech-g45.body_side_flat_top_above_axis":0.334,"eotech-g45.body_top_above_axis":0.872,"eotech-g45.clamp_bottom_y":-0.37,"eotech-g45.clamp_length":1.395,"eotech-g45.clamp_nut_above_clamp_bottom":0.32,"eotech-g45.clamp_nut_d":0.36,"eotech-g45.collar_pad_angle":34,"eotech-g45.collar_pad_front_behind_base":0.176,"eotech-g45.collar_pad_length":0.889,"eotech-g45.collar_pad_relief":0.027,"eotech-g45.collar_pads":7,"eotech-g45.collar_panel_angle":22,"eotech-g45.collar_panel_depth":0.027,"eotech-g45.collar_panel_length":0.787,"eotech-g45.collar_top_pad_angle":44,"eotech-g45.diopter_flute_angle":8,"eotech-g45.diopter_flute_depth":0.028,"eotech-g45.diopter_flutes":20,"eotech-g45.eyepiece_glass_d":0.92,"eotech-g45.eyepiece_neck_od":1.295,"eotech-g45.eyepiece_rear_behind_base":2.933,"eotech-g45.eyepiece_ring_od":1.512,"eotech-g45.flip_angle":93.5,"eotech-g45.height":3.2992125984251968,"eotech-g45.hinge_axis_above_clamp_bottom":0.871,"eotech-g45.hinge_axis_right_of_centre":0.69,"eotech-g45.hinge_barrel_d":0.5,"eotech-g45.hinge_block_length":1.394,"eotech-g45.hinge_knuckle_d":0.62,"eotech-g45.hinge_knuckle_length":0.37,"eotech-g45.hinge_pin_d":0.316,"eotech-g45.hinge_web_inner_right_of_centre":0.13,"eotech-g45.knob_lugs":8,"eotech-g45.knob_notch_angle":24,"eotech-g45.knob_notch_depth":0.035,"eotech-g45.knob_notch_phase":30,"eotech-g45.length":3.751,"eotech-g45.lever_tail_behind_base":1.318,"eotech-g45.lever_thickness":0.2,"eotech-g45.objective_front_ahead_of_base":0.819,"eotech-g45.objective_glass_d":0.984251968503937,"eotech-g45.objective_tube_od":1.512,"eotech-g45.optical_axis_above_rail_no_spacer":1.55,"eotech-g45.optical_axis_above_rail_spacer":1.826,"eotech-g45.plate_bottom_above_clamp_bottom":0.866,"eotech-g45.plate_top_above_clamp_bottom":1.1,"eotech-g45.plate_width":0.64,"eotech-g45.riser_length":1.608,"eotech-g45.riser_thickness":0.2755905511811024,"eotech-g45.riser_top_above_clamp_bottom":1.385,"eotech-g45.riser_width":0.75,"eotech-g45.side_knob_reach":1.1227,"eotech-g45.sts_mount_height":1.1811,"eotech-g45.sts_mount_length":1.6614,"eotech-g45.top_knob_behind_base":1.675,"eotech-g45.top_knob_d":0.675,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{"side":[[-2.932,2.692],[-2.928,1.625],[-2.921,1.481],[-2.904,1.448],[-2.879,1.441],[-2.676,1.446],[-2.645,1.467],[-2.641,1.547],[-2.592,1.548],[-2.582,1.557],[-2.577,1.408],[-2.562,1.393],[-2.503,1.386],[-1.239,1.377],[-1.134,1.396],[-0.804,1.398],[-0.803,1.139],[-0.828,1.128],[-0.83,0.904],[-0.808,0.86],[-0.709,0.859],[-0.711,0.592],[-1.308,0.581],[-1.316,0.571],[-1.318,0.489],[-1.318,0.09],[-1.296,0.08],[-0.699,0.089],[-0.693,0.086],[-0.702,0.079],[-0.716,0.019],[-0.703,0.011],[-0.314,0.011],[-0.065,0],[-0.001,0],[0.544,0.002],[0.692,0.009],[0.705,0.019],[0.702,0.147],[0.714,0.161],[0.714,0.496],[0.702,0.505],[0.709,0.573],[0.661,0.631],[0.654,0.852],[0.813,0.857],[0.83,0.877],[0.83,1.068],[0.81,1.096],[0.81,1.353],[0.798,1.367],[0.814,1.773],[0.819,2.416],[0.814,2.715],[0.791,2.945],[0.776,2.953],[-0.092,2.951],[-0.105,2.961],[-0.114,3.029],[-0.184,3.069],[-1.059,3.062],[-1.089,3.058],[-1.118,3.04],[-1.155,3.04],[-1.187,3.056],[-1.34,3.067],[-1.341,3.114],[-1.366,3.13],[-1.368,3.146],[-1.366,3.168],[-1.339,3.194],[-1.339,3.228],[-1.39,3.286],[-1.451,3.297],[-1.584,3.302],[-1.837,3.302],[-1.96,3.29],[-2.014,3.23],[-2.014,3.189],[-1.986,3.168],[-1.984,3.134],[-2.016,3.107],[-2.015,3.069],[-2.466,3.069],[-2.535,3.056],[-2.56,3.042],[-2.57,3.023],[-2.582,2.814],[-2.594,2.846],[-2.645,2.849],[-2.65,2.927],[-2.683,2.951],[-2.909,2.948],[-2.923,2.915]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"y":"clamp_bottom_y"}}},"bounds":{"min":[-2.9301,-0.37,-1],"max":[0.8307,2.0088,3.1667]},"axis_y":1.1088,"axis_z":2.0547,"volume_in3":10.7142,"centroid":[-0.8921,0.9466,1.7086],"shell":[-0.7438,0.8496,1.4653],"area_in2":61.7538,"triangles":17472,"manifold":true,"rail_seat":{"x":[-0.6975,0.6975],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-1.318,-0.37,-1,0.714,0.185,-0.621],[-0.697,-0.37,-0.621,0.697,0.185,-0.242],[-0.697,0,-0.242,0.697,0.492,0.136],[-0.697,-0.37,0.136,0.697,0.757,0.515],[-0.831,-0.37,0.515,0.831,1.509,0.894],[-2.572,-0.37,0.894,0.831,1.55,1.273],[-2.934,0.303,1.273,0.821,1.912,1.652],[-2.934,-0.023,1.652,0.821,2.009,2.409],[-2.934,0.265,2.409,0.821,1.958,2.788],[-2.917,0.601,2.788,0.792,1.588,3.167]],"slots":["body","tube","mount","hardware","pin","lens"]},"eotech-g45.aside_no_riser":{"part":"eotech-g45","component":"aside_no_riser","model":"eotech-g45.aside_no_riser.glb","script":"eotech_g45.py","inputs":{"eotech-g45.axis_above_clamp_bottom":2.196,"eotech-g45.base_left_of_centre":1,"eotech-g45.base_top_above_clamp_bottom":0.555,"eotech-g45.body_bottom_below_axis":0.82,"eotech-g45.body_half_width":0.8915,"eotech-g45.body_height":1.692,"eotech-g45.body_side_flat_bottom_below_axis":0.373,"eotech-g45.body_side_flat_top_above_axis":0.334,"eotech-g45.body_top_above_axis":0.872,"eotech-g45.clamp_bottom_y":-0.37,"eotech-g45.clamp_length":1.395,"eotech-g45.clamp_nut_above_clamp_bottom":0.32,"eotech-g45.clamp_nut_d":0.36,"eotech-g45.collar_pad_angle":34,"eotech-g45.collar_pad_front_behind_base":0.176,"eotech-g45.collar_pad_length":0.889,"eotech-g45.collar_pad_relief":0.027,"eotech-g45.collar_pads":7,"eotech-g45.collar_panel_angle":22,"eotech-g45.collar_panel_depth":0.027,"eotech-g45.collar_panel_length":0.787,"eotech-g45.collar_top_pad_angle":44,"eotech-g45.diopter_flute_angle":8,"eotech-g45.diopter_flute_depth":0.028,"eotech-g45.diopter_flutes":20,"eotech-g45.eyepiece_glass_d":0.92,"eotech-g45.eyepiece_neck_od":1.295,"eotech-g45.eyepiece_rear_behind_base":2.933,"eotech-g45.eyepiece_ring_od":1.512,"eotech-g45.flip_angle":93.5,"eotech-g45.height":3.2992125984251968,"eotech-g45.hinge_axis_above_clamp_bottom":0.871,"eotech-g45.hinge_axis_right_of_centre":0.69,"eotech-g45.hinge_barrel_d":0.5,"eotech-g45.hinge_block_length":1.394,"eotech-g45.hinge_knuckle_d":0.62,"eotech-g45.hinge_knuckle_length":0.37,"eotech-g45.hinge_pin_d":0.316,"eotech-g45.hinge_web_inner_right_of_centre":0.13,"eotech-g45.knob_lugs":8,"eotech-g45.knob_notch_angle":24,"eotech-g45.knob_notch_depth":0.035,"eotech-g45.knob_notch_phase":30,"eotech-g45.length":3.751,"eotech-g45.lever_tail_behind_base":1.318,"eotech-g45.lever_thickness":0.2,"eotech-g45.objective_front_ahead_of_base":0.819,"eotech-g45.objective_glass_d":0.984251968503937,"eotech-g45.objective_tube_od":1.512,"eotech-g45.optical_axis_above_rail_no_spacer":1.55,"eotech-g45.optical_axis_above_rail_spacer":1.826,"eotech-g45.plate_bottom_above_clamp_bottom":0.866,"eotech-g45.plate_top_above_clamp_bottom":1.1,"eotech-g45.plate_width":0.64,"eotech-g45.riser_length":1.608,"eotech-g45.riser_thickness":0.2755905511811024,"eotech-g45.riser_top_above_clamp_bottom":1.385,"eotech-g45.riser_width":0.75,"eotech-g45.side_knob_reach":1.1227,"eotech-g45.sts_mount_height":1.1811,"eotech-g45.sts_mount_length":1.6614,"eotech-g45.top_knob_behind_base":1.675,"eotech-g45.top_knob_d":0.675,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{"side":[[-2.932,2.692],[-2.928,1.625],[-2.921,1.481],[-2.904,1.448],[-2.879,1.441],[-2.676,1.446],[-2.645,1.467],[-2.641,1.547],[-2.592,1.548],[-2.582,1.557],[-2.577,1.408],[-2.562,1.393],[-2.503,1.386],[-1.239,1.377],[-1.134,1.396],[-0.804,1.398],[-0.803,1.139],[-0.828,1.128],[-0.83,0.904],[-0.808,0.86],[-0.709,0.859],[-0.711,0.592],[-1.308,0.581],[-1.316,0.571],[-1.318,0.489],[-1.318,0.09],[-1.296,0.08],[-0.699,0.089],[-0.693,0.086],[-0.702,0.079],[-0.716,0.019],[-0.703,0.011],[-0.314,0.011],[-0.065,0],[-0.001,0],[0.544,0.002],[0.692,0.009],[0.705,0.019],[0.702,0.147],[0.714,0.161],[0.714,0.496],[0.702,0.505],[0.709,0.573],[0.661,0.631],[0.654,0.852],[0.813,0.857],[0.83,0.877],[0.83,1.068],[0.81,1.096],[0.81,1.353],[0.798,1.367],[0.814,1.773],[0.819,2.416],[0.814,2.715],[0.791,2.945],[0.776,2.953],[-0.092,2.951],[-0.105,2.961],[-0.114,3.029],[-0.184,3.069],[-1.059,3.062],[-1.089,3.058],[-1.118,3.04],[-1.155,3.04],[-1.187,3.056],[-1.34,3.067],[-1.341,3.114],[-1.366,3.13],[-1.368,3.146],[-1.366,3.168],[-1.339,3.194],[-1.339,3.228],[-1.39,3.286],[-1.451,3.297],[-1.584,3.302],[-1.837,3.302],[-1.96,3.29],[-2.014,3.23],[-2.014,3.189],[-1.986,3.168],[-1.984,3.134],[-2.016,3.107],[-2.015,3.069],[-2.466,3.069],[-2.535,3.056],[-2.56,3.042],[-2.57,3.023],[-2.582,2.814],[-2.594,2.846],[-2.645,2.849],[-2.65,2.927],[-2.683,2.951],[-2.909,2.948],[-2.923,2.915]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"y":"clamp_bottom_y"}}},"bounds":{"min":[-2.9301,-0.37,-1],"max":[0.8307,2.0257,2.8912]},"axis_y":1.1257,"axis_z":1.7792,"volume_in3":10.3862,"centroid":[-0.9203,0.9534,1.503],"shell":[-0.7911,0.8408,1.3014],"area_in2":58.059,"triangles":17460,"manifold":true,"rail_seat":{"x":[-0.6975,0.6975],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-1.318,-0.37,-1,0.714,0.185,-0.611],[-0.697,-0.37,-0.611,0.697,0.185,-0.222],[-0.697,0,-0.222,0.697,0.492,0.167],[-0.709,-0.37,0.167,0.709,0.78,0.556],[-2.56,-0.37,0.556,0.831,1.509,0.946],[-2.934,-0.37,0.946,0.831,1.906,1.335],[-2.934,-0.006,1.335,0.821,2.026,2.113],[-2.934,0.265,2.113,0.821,1.983,2.502],[-2.921,0.608,2.502,0.794,1.616,2.891]],"slots":["body","tube","mount","hardware","pin","lens"]},"eotech-g45.inline":{"part":"eotech-g45","component":"inline","model":"eotech-g45.inline.glb","script":"eotech_g45.py","inputs":{"eotech-g45.axis_above_clamp_bottom":2.196,"eotech-g45.base_left_of_centre":1,"eotech-g45.base_top_above_clamp_bottom":0.555,"eotech-g45.body_bottom_below_axis":0.82,"eotech-g45.body_half_width":0.8915,"eotech-g45.body_height":1.692,"eotech-g45.body_side_flat_bottom_below_axis":0.373,"eotech-g45.body_side_flat_top_above_axis":0.334,"eotech-g45.body_top_above_axis":0.872,"eotech-g45.clamp_bottom_y":-0.37,"eotech-g45.clamp_length":1.395,"eotech-g45.clamp_nut_above_clamp_bottom":0.32,"eotech-g45.clamp_nut_d":0.36,"eotech-g45.collar_pad_angle":34,"eotech-g45.collar_pad_front_behind_base":0.176,"eotech-g45.collar_pad_length":0.889,"eotech-g45.collar_pad_relief":0.027,"eotech-g45.collar_pads":7,"eotech-g45.collar_panel_angle":22,"eotech-g45.collar_panel_depth":0.027,"eotech-g45.collar_panel_length":0.787,"eotech-g45.collar_top_pad_angle":44,"eotech-g45.diopter_flute_angle":8,"eotech-g45.diopter_flute_depth":0.028,"eotech-g45.diopter_flutes":20,"eotech-g45.eyepiece_glass_d":0.92,"eotech-g45.eyepiece_neck_od":1.295,"eotech-g45.eyepiece_rear_behind_base":2.933,"eotech-g45.eyepiece_ring_od":1.512,"eotech-g45.flip_angle":93.5,"eotech-g45.height":3.2992125984251968,"eotech-g45.hinge_axis_above_clamp_bottom":0.871,"eotech-g45.hinge_axis_right_of_centre":0.69,"eotech-g45.hinge_barrel_d":0.5,"eotech-g45.hinge_block_length":1.394,"eotech-g45.hinge_knuckle_d":0.62,"eotech-g45.hinge_knuckle_length":0.37,"eotech-g45.hinge_pin_d":0.316,"eotech-g45.hinge_web_inner_right_of_centre":0.13,"eotech-g45.knob_lugs":8,"eotech-g45.knob_notch_angle":24,"eotech-g45.knob_notch_depth":0.035,"eotech-g45.knob_notch_phase":30,"eotech-g45.length":3.751,"eotech-g45.lever_tail_behind_base":1.318,"eotech-g45.lever_thickness":0.2,"eotech-g45.objective_front_ahead_of_base":0.819,"eotech-g45.objective_glass_d":0.984251968503937,"eotech-g45.objective_tube_od":1.512,"eotech-g45.optical_axis_above_rail_no_spacer":1.55,"eotech-g45.optical_axis_above_rail_spacer":1.826,"eotech-g45.plate_bottom_above_clamp_bottom":0.866,"eotech-g45.plate_top_above_clamp_bottom":1.1,"eotech-g45.plate_width":0.64,"eotech-g45.riser_length":1.608,"eotech-g45.riser_thickness":0.2755905511811024,"eotech-g45.riser_top_above_clamp_bottom":1.385,"eotech-g45.riser_width":0.75,"eotech-g45.side_knob_reach":1.1227,"eotech-g45.sts_mount_height":1.1811,"eotech-g45.sts_mount_length":1.6614,"eotech-g45.top_knob_behind_base":1.675,"eotech-g45.top_knob_d":0.675,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{"side":[[-2.932,2.692],[-2.928,1.625],[-2.921,1.481],[-2.904,1.448],[-2.879,1.441],[-2.676,1.446],[-2.645,1.467],[-2.641,1.547],[-2.592,1.548],[-2.582,1.557],[-2.577,1.408],[-2.562,1.393],[-2.503,1.386],[-1.239,1.377],[-1.134,1.396],[-0.804,1.398],[-0.803,1.139],[-0.828,1.128],[-0.83,0.904],[-0.808,0.86],[-0.709,0.859],[-0.711,0.592],[-1.308,0.581],[-1.316,0.571],[-1.318,0.489],[-1.318,0.09],[-1.296,0.08],[-0.699,0.089],[-0.693,0.086],[-0.702,0.079],[-0.716,0.019],[-0.703,0.011],[-0.314,0.011],[-0.065,0],[-0.001,0],[0.544,0.002],[0.692,0.009],[0.705,0.019],[0.702,0.147],[0.714,0.161],[0.714,0.496],[0.702,0.505],[0.709,0.573],[0.661,0.631],[0.654,0.852],[0.813,0.857],[0.83,0.877],[0.83,1.068],[0.81,1.096],[0.81,1.353],[0.798,1.367],[0.814,1.773],[0.819,2.416],[0.814,2.715],[0.791,2.945],[0.776,2.953],[-0.092,2.951],[-0.105,2.961],[-0.114,3.029],[-0.184,3.069],[-1.059,3.062],[-1.089,3.058],[-1.118,3.04],[-1.155,3.04],[-1.187,3.056],[-1.34,3.067],[-1.341,3.114],[-1.366,3.13],[-1.368,3.146],[-1.366,3.168],[-1.339,3.194],[-1.339,3.228],[-1.39,3.286],[-1.451,3.297],[-1.584,3.302],[-1.837,3.302],[-1.96,3.29],[-2.014,3.23],[-2.014,3.189],[-1.986,3.168],[-1.984,3.134],[-2.016,3.107],[-2.015,3.069],[-2.466,3.069],[-2.535,3.056],[-2.56,3.042],[-2.57,3.023],[-2.582,2.814],[-2.594,2.846],[-2.645,2.849],[-2.65,2.927],[-2.683,2.951],[-2.909,2.948],[-2.923,2.915]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"y":"clamp_bottom_y"}}},"bounds":{"min":[-2.9301,-0.37,-1],"max":[0.8307,2.9291,1.1227]},"axis_y":1.826,"axis_z":0,"volume_in3":10.7142,"centroid":[-0.8921,1.5065,0.0307],"shell":[-0.7438,1.2858,0.0582],"area_in2":61.7538,"triangles":17472,"manifold":true,"rail_seat":{"x":[-0.6975,0.6975],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-2.934,1.006,-0.891,-2.181,2.698,0.891],[-2.181,1.006,-0.891,-1.428,2.929,1.123],[-1.428,-0.29,-1,-1.052,2.921,1.115],[-1.052,-0.37,-1,0.078,2.698,1.03],[0.078,-0.37,-1,0.831,2.582,1.03]],"slots":["body","tube","mount","hardware","pin","lens"]},"eotech-g45.inline_no_riser":{"part":"eotech-g45","component":"inline_no_riser","model":"eotech-g45.inline_no_riser.glb","script":"eotech_g45.py","inputs":{"eotech-g45.axis_above_clamp_bottom":2.196,"eotech-g45.base_left_of_centre":1,"eotech-g45.base_top_above_clamp_bottom":0.555,"eotech-g45.body_bottom_below_axis":0.82,"eotech-g45.body_half_width":0.8915,"eotech-g45.body_height":1.692,"eotech-g45.body_side_flat_bottom_below_axis":0.373,"eotech-g45.body_side_flat_top_above_axis":0.334,"eotech-g45.body_top_above_axis":0.872,"eotech-g45.clamp_bottom_y":-0.37,"eotech-g45.clamp_length":1.395,"eotech-g45.clamp_nut_above_clamp_bottom":0.32,"eotech-g45.clamp_nut_d":0.36,"eotech-g45.collar_pad_angle":34,"eotech-g45.collar_pad_front_behind_base":0.176,"eotech-g45.collar_pad_length":0.889,"eotech-g45.collar_pad_relief":0.027,"eotech-g45.collar_pads":7,"eotech-g45.collar_panel_angle":22,"eotech-g45.collar_panel_depth":0.027,"eotech-g45.collar_panel_length":0.787,"eotech-g45.collar_top_pad_angle":44,"eotech-g45.diopter_flute_angle":8,"eotech-g45.diopter_flute_depth":0.028,"eotech-g45.diopter_flutes":20,"eotech-g45.eyepiece_glass_d":0.92,"eotech-g45.eyepiece_neck_od":1.295,"eotech-g45.eyepiece_rear_behind_base":2.933,"eotech-g45.eyepiece_ring_od":1.512,"eotech-g45.flip_angle":93.5,"eotech-g45.height":3.2992125984251968,"eotech-g45.hinge_axis_above_clamp_bottom":0.871,"eotech-g45.hinge_axis_right_of_centre":0.69,"eotech-g45.hinge_barrel_d":0.5,"eotech-g45.hinge_block_length":1.394,"eotech-g45.hinge_knuckle_d":0.62,"eotech-g45.hinge_knuckle_length":0.37,"eotech-g45.hinge_pin_d":0.316,"eotech-g45.hinge_web_inner_right_of_centre":0.13,"eotech-g45.knob_lugs":8,"eotech-g45.knob_notch_angle":24,"eotech-g45.knob_notch_depth":0.035,"eotech-g45.knob_notch_phase":30,"eotech-g45.length":3.751,"eotech-g45.lever_tail_behind_base":1.318,"eotech-g45.lever_thickness":0.2,"eotech-g45.objective_front_ahead_of_base":0.819,"eotech-g45.objective_glass_d":0.984251968503937,"eotech-g45.objective_tube_od":1.512,"eotech-g45.optical_axis_above_rail_no_spacer":1.55,"eotech-g45.optical_axis_above_rail_spacer":1.826,"eotech-g45.plate_bottom_above_clamp_bottom":0.866,"eotech-g45.plate_top_above_clamp_bottom":1.1,"eotech-g45.plate_width":0.64,"eotech-g45.riser_length":1.608,"eotech-g45.riser_thickness":0.2755905511811024,"eotech-g45.riser_top_above_clamp_bottom":1.385,"eotech-g45.riser_width":0.75,"eotech-g45.side_knob_reach":1.1227,"eotech-g45.sts_mount_height":1.1811,"eotech-g45.sts_mount_length":1.6614,"eotech-g45.top_knob_behind_base":1.675,"eotech-g45.top_knob_d":0.675,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{"side":[[-2.932,2.692],[-2.928,1.625],[-2.921,1.481],[-2.904,1.448],[-2.879,1.441],[-2.676,1.446],[-2.645,1.467],[-2.641,1.547],[-2.592,1.548],[-2.582,1.557],[-2.577,1.408],[-2.562,1.393],[-2.503,1.386],[-1.239,1.377],[-1.134,1.396],[-0.804,1.398],[-0.803,1.139],[-0.828,1.128],[-0.83,0.904],[-0.808,0.86],[-0.709,0.859],[-0.711,0.592],[-1.308,0.581],[-1.316,0.571],[-1.318,0.489],[-1.318,0.09],[-1.296,0.08],[-0.699,0.089],[-0.693,0.086],[-0.702,0.079],[-0.716,0.019],[-0.703,0.011],[-0.314,0.011],[-0.065,0],[-0.001,0],[0.544,0.002],[0.692,0.009],[0.705,0.019],[0.702,0.147],[0.714,0.161],[0.714,0.496],[0.702,0.505],[0.709,0.573],[0.661,0.631],[0.654,0.852],[0.813,0.857],[0.83,0.877],[0.83,1.068],[0.81,1.096],[0.81,1.353],[0.798,1.367],[0.814,1.773],[0.819,2.416],[0.814,2.715],[0.791,2.945],[0.776,2.953],[-0.092,2.951],[-0.105,2.961],[-0.114,3.029],[-0.184,3.069],[-1.059,3.062],[-1.089,3.058],[-1.118,3.04],[-1.155,3.04],[-1.187,3.056],[-1.34,3.067],[-1.341,3.114],[-1.366,3.13],[-1.368,3.146],[-1.366,3.168],[-1.339,3.194],[-1.339,3.228],[-1.39,3.286],[-1.451,3.297],[-1.584,3.302],[-1.837,3.302],[-1.96,3.29],[-2.014,3.23],[-2.014,3.189],[-1.986,3.168],[-1.984,3.134],[-2.016,3.107],[-2.015,3.069],[-2.466,3.069],[-2.535,3.056],[-2.56,3.042],[-2.57,3.023],[-2.582,2.814],[-2.594,2.846],[-2.645,2.849],[-2.65,2.927],[-2.683,2.951],[-2.909,2.948],[-2.923,2.915]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"y":"clamp_bottom_y"}}},"bounds":{"min":[-2.9301,-0.37,-1],"max":[0.8307,2.6531,1.1227]},"axis_y":1.55,"axis_z":0,"volume_in3":10.3862,"centroid":[-0.9203,1.3013,0.0317],"shell":[-0.7911,1.1248,0.0619],"area_in2":58.059,"triangles":17460,"manifold":true,"rail_seat":{"x":[-0.6975,0.6975],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-2.934,0.73,-0.891,-2.181,2.422,0.891],[-2.181,0.73,-0.891,-1.428,2.653,1.123],[-1.428,-0.29,-1,-1.052,2.645,1.115],[-1.052,-0.37,-1,0.078,2.422,1.03],[0.078,-0.37,-1,0.831,2.306,1.03]],"slots":["body","tube","mount","hardware","pin","lens"]},"expo-arms-mlok-15-handguard":{"part":"expo-arms-mlok-15-handguard","model":"expo-arms-mlok-15-handguard.glb","script":"expo_arms_mlok_15_handguard.py","inputs":{"expo-arms-mlok-15-handguard.bolt_below_bore":0.94,"expo-arms-mlok-15-handguard.bolt_end_diameter":0.19,"expo-arms-mlok-15-handguard.bolt_first_from_rear_face":0.5,"expo-arms-mlok-15-handguard.bolt_head_diameter":0.3,"expo-arms-mlok-15-handguard.bolt_spacing":0.5,"expo-arms-mlok-15-handguard.bottom_below_bore":0.76,"expo-arms-mlok-15-handguard.channel_width":0.45,"expo-arms-mlok-15-handguard.diagonal_face_distance":0.775,"expo-arms-mlok-15-handguard.inside_diameter":1.35,"expo-arms-mlok-15-handguard.mlok_slot0_x":2.49,"expo-arms-mlok-15-handguard.mlok_slots":8,"expo-arms-mlok-15-handguard.neck_bottom_above_bore":0.73,"expo-arms-mlok-15-handguard.nut_face_diameter":0.44,"expo-arms-mlok-15-handguard.nut_shoulder_above_bolt":0.34,"expo-arms-mlok-15-handguard.nut_shoulder_width":0.2,"expo-arms-mlok-15-handguard.nut_tip_above_bolt":0.375,"expo-arms-mlok-15-handguard.overall_length":15.18,"expo-arms-mlok-15-handguard.rail_front_chamfer":0.11,"expo-arms-mlok-15-handguard.rail_slot0_from_rear_face":0.62,"expo-arms-mlok-15-handguard.rail_slots":36,"expo-arms-mlok-15-handguard.rail_top_above_bore":1.2,"expo-arms-mlok-15-handguard.rail_top_flat_width":0.64,"expo-arms-mlok-15-handguard.rail_underside_below_top":0.21,"expo-arms-mlok-15-handguard.rail_widest_below_top":0.1,"expo-arms-mlok-15-handguard.rear_face_x":-0.445,"expo-arms-mlok-15-handguard.rear_x":-0.635,"expo-arms-mlok-15-handguard.tab_length":0.19,"expo-arms-mlok-15-handguard.tab_root_bottom_above_bore":0.47,"expo-arms-mlok-15-handguard.tab_tip_bottom_above_bore":0.56,"expo-arms-mlok-15-handguard.tab_top_above_bore":0.71,"expo-arms-mlok-15-handguard.width":1.59,"std.ar15.gas_tube_above_bore":0.78,"std.mlok.slot_corner_r":0.0937007874015748,"std.mlok.slot_length":1.2598425196850394,"std.mlok.slot_pitch":1.574803149606299,"std.mlok.slot_width":0.2755905511811024,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{"side":[[0,-0.51],[0.003,-0.649],[0.123,-0.704],[0.159,-0.738],[0.116,-0.925],[0.12,-1.527],[0.238,-2.003],[0.32,-2.052],[0.402,-2.131],[0.458,-2.231],[0.525,-2.303],[0.611,-2.347],[1.53,-2.36],[1.762,-2.356],[1.823,-2.339],[1.969,-2.259],[2.134,-2.047],[2.195,-2.007],[2.264,-1.991],[15.021,-1.98],[15.062,-1.937],[15.17,-1.549],[15.18,-1.248],[15.174,-0.916],[15.064,-0.455],[15.073,-0.115],[14.982,-0.02],[14.45,-0.03],[14.395,-0.016],[14.133,-0.013],[14.071,-0.03],[14.017,-0.016],[13.793,-0.012],[13.685,-0.03],[13.469,-0.011],[13.353,-0.013],[13.299,-0.03],[13.152,-0.009],[12.982,-0.013],[12.921,-0.029],[12.789,-0.009],[12.596,-0.013],[12.535,-0.029],[12.457,-0.008],[12.218,-0.012],[12.149,-0.029],[12.079,-0.007],[11.839,-0.012],[11.762,-0.029],[11.693,-0.007],[11.453,-0.012],[11.384,-0.036],[11.299,-0.007],[11.067,-0.012],[10.998,-0.036],[10.913,-0.007],[10.689,-0.011],[10.604,-0.036],[10.519,-0.007],[10.303,-0.011],[10.218,-0.036],[10.133,-0.007],[9.917,-0.011],[9.832,-0.043],[9.786,-0.037],[9.739,-0.007],[9.538,-0.011],[9.492,-0.042],[9.446,-0.051],[9.4,-0.044],[9.345,-0.007],[9.206,-0.002],[9.053,-0.051],[9.006,-0.044],[8.951,-0.007],[8.843,-0.001],[8.789,-0.002],[8.72,-0.042],[8.666,-0.051],[8.62,-0.044],[8.565,-0.006],[8.457,-0.001],[8.403,-0.002],[8.327,-0.05],[8.28,-0.058],[8.218,-0.044],[8.171,-0.006],[8.094,0],[8.009,-0.002],[7.941,-0.05],[7.887,-0.058],[7.84,-0.052],[7.778,-0.006],[7.662,-0.001],[7.623,-0.002],[7.577,-0.041],[7.501,-0.066],[7.423,-0.044],[7.384,-0.006],[7.314,0],[7.221,-0.002],[7.153,-0.057],[7.099,-0.066],[7.022,-0.044],[6.982,-0.007],[6.92,0],[6.828,-0.002],[6.79,-0.041],[6.713,-0.066],[6.635,-0.044],[6.596,-0.006],[6.527,0],[6.434,-0.002],[6.373,-0.049],[6.319,-0.058],[6.242,-0.036],[6.21,-0.006],[6.117,0],[6.04,-0.002],[6.01,-0.033],[5.933,-0.058],[5.887,-0.051],[5.816,-0.006],[5.723,0],[5.646,-0.002],[5.593,-0.041],[5.539,-0.05],[5.493,-0.043],[5.438,-0.006],[5.314,-0.001],[5.252,-0.002],[5.199,-0.041],[5.153,-0.05],[5.107,-0.043],[5.052,-0.006],[4.944,0],[4.859,-0.002],[4.813,-0.034],[4.759,-0.042],[4.713,-0.035],[4.666,-0.006],[4.48,-0.001],[4.373,-0.042],[4.326,-0.035],[4.28,-0.005],[4.117,-0.001],[4.071,-0.002],[3.979,-0.034],[3.893,-0.005],[3.708,-0.001],[3.593,-0.034],[3.507,-0.005],[3.276,-0.01],[3.207,-0.034],[3.121,-0.005],[2.882,-0.01],[2.813,-0.026],[2.743,-0.005],[2.488,-0.01],[2.419,-0.026],[2.349,-0.005],[2.102,-0.009],[2.033,-0.026],[1.955,-0.005],[1.716,-0.009],[1.655,-0.026],[1.507,-0.006],[1.322,-0.009],[1.268,-0.026],[1.098,-0.006],[0.936,-0.009],[0.882,-0.026],[0.666,-0.007],[0.226,-0.015],[0.193,-0.089],[0.21,-0.189],[0.214,-0.374],[0.199,-0.413],[0.123,-0.477],[0.169,-0.483],[0.019,-0.49]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"x":"rear_x","y":"rail_top_above_bore"}}},"bounds":{"min":[-0.635,-1.135,-0.795],"max":[14.545,1.2,0.795]},"volume_in3":8.8668,"centroid":[6.5194,0.2321,-0.0001],"shell":[6.8085,0.2163,0.0004],"area_in2":154.0793,"triangles":36920,"manifold":true,"slabs":[[-0.635,-0.904,-0.795,-0.236,1.2,0.795],[-0.236,-1.135,-0.795,1.362,1.2,0.795],[1.362,-0.998,-0.795,1.762,1.2,0.795],[1.762,-0.76,-0.795,14.545,1.2,0.795]],"slots":["body","hardware"]},"expo-arms-stripped-upper.receiver":{"part":"expo-arms-stripped-upper","component":"receiver","model":"expo-arms-stripped-upper.receiver.glb","script":"expo_arms_stripped_upper.py","inputs":{"expo-arms-stripped-upper.barrel_thread_major_d":1.2442,"expo-arms-stripped-upper.barrel_thread_minor_d":1.1803,"expo-arms-stripped-upper.barrel_thread_tpi":18,"expo-arms-stripped-upper.body_radius":0.59,"expo-arms-stripped-upper.bore_axis_above_pin":0.8775,"expo-arms-stripped-upper.bore_d":1,"expo-arms-stripped-upper.cam_pad_face_z":0.5625,"expo-arms-stripped-upper.deflector_crest_x":2.32,"expo-arms-stripped-upper.deflector_front_out":0.82,"expo-arms-stripped-upper.deflector_out":1.25,"expo-arms-stripped-upper.dovetail_foot_half_width":0.321,"expo-arms-stripped-upper.dovetail_foot_y":1.885,"expo-arms-stripped-upper.fa_axis_angle":20,"expo-arms-stripped-upper.fa_axis_x":-0.395,"expo-arms-stripped-upper.fa_axis_z":1.09,"expo-arms-stripped-upper.fa_bore_d":0.509,"expo-arms-stripped-upper.fa_bore_depth":0.65,"expo-arms-stripped-upper.fa_housing_r":0.3125,"expo-arms-stripped-upper.fa_inner_bore_d":0.315,"expo-arms-stripped-upper.fa_rear_x":-0.49,"expo-arms-stripped-upper.front_face_x":7.036,"expo-arms-stripped-upper.gas_tube_hole_d":0.1835,"expo-arms-stripped-upper.gas_tube_relief_d":0.094,"expo-arms-stripped-upper.gas_tube_relief_offset":0.078,"expo-arms-stripped-upper.handle_seat_x":0.069,"expo-arms-stripped-upper.hinge_axis_y":0.641,"expo-arms-stripped-upper.hinge_axis_z":0.689,"expo-arms-stripped-upper.hinge_boss_r":0.1365,"expo-arms-stripped-upper.hinge_pin_d":0.1295,"expo-arms-stripped-upper.left_photo_lens_distance":34.8,"expo-arms-stripped-upper.left_photo_lens_x":3.36,"expo-arms-stripped-upper.left_photo_lens_y":4.8,"expo-arms-stripped-upper.lug_hole_d":0.251,"expo-arms-stripped-upper.lug_rear_face_top_y":0.458,"expo-arms-stripped-upper.lug_wall_half_width":0.453,"expo-arms-stripped-upper.lug_width":0.4945,"expo-arms-stripped-upper.port_bottom_y":0.841,"expo-arms-stripped-upper.port_end_r":0.25,"expo-arms-stripped-upper.port_front_x":6.036,"expo-arms-stripped-upper.port_length":3.125,"expo-arms-stripped-upper.rail_front_x":6.591,"expo-arms-stripped-upper.rail_neck_bottom_y":1.7,"expo-arms-stripped-upper.rail_neck_half_width":0.309,"expo-arms-stripped-upper.rail_tongue_rear_x":-0.588,"expo-arms-stripped-upper.rail_top_above_pin":2.092,"expo-arms-stripped-upper.rear_flange_front_x":-0.47,"expo-arms-stripped-upper.rear_flange_r":0.6938,"expo-arms-stripped-upper.receiver_rear_x":-0.621,"expo-arms-stripped-upper.right_photo_lens_distance":36,"expo-arms-stripped-upper.right_photo_lens_x":1.69,"expo-arms-stripped-upper.right_photo_lens_y":1.04,"expo-arms-stripped-upper.side_bottom_y":1.44,"expo-arms-stripped-upper.side_half_width":0.319,"expo-arms-stripped-upper.underside_y":0.2485,"std.ar15.buffer_tower_front_x":-0.628,"std.ar15.charging_handle_channel_floor_y":1.5845,"std.ar15.charging_handle_channel_front_round_x":5.726,"std.ar15.charging_handle_channel_rear_half_width":0.209,"std.ar15.charging_handle_channel_rear_round_x":0.676,"std.ar15.charging_handle_channel_roof_y":1.9085,"std.ar15.charging_handle_channel_round_r":0.2665,"std.ar15.charging_handle_channel_slot_half_width":0.205,"std.ar15.charging_handle_channel_tier_half_width":0.25,"std.ar15.charging_handle_channel_tier_top_y":1.7115,"std.ar15.charging_handle_channel_top_half_width":0.22,"std.ar15.charging_handle_latch_slot_floor":0.045,"std.ar15.charging_handle_notch_chamfer":0.083,"std.ar15.charging_handle_notch_floor_y":1.571,"std.ar15.charging_handle_notch_roof_y":1.89,"std.ar15.deck_y":0.2485,"std.ar15.gas_tube_above_bore":0.78,"std.ar15.pin_spacing":6.375,"std.ar15.rail_tongue_end_r":0.4175,"std.ar15.rail_tongue_fillet_r":0.1476,"std.ar15.rail_tongue_front_x":0.277,"std.ar15.rail_tongue_half_width":0.318,"std.ar15.rail_tongue_shoulder_x":0.4165,"std.ar15.rear_wall_arc_r":0.75,"std.ar15.upper_barrel_thread_length":0.445,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.top_width":0.835},"profiles":{"side":[[-0.621,1.594],[-0.621,0.645],[-0.561,0.543],[-0.378,0.403],[-0.244,0.323],[-0.243,-0.132],[-0.225,-0.22],[0.222,-0.219],[0.244,-0.202],[0.247,-0.163],[0.247,0.238],[0.634,0.245],[6.135,0.246],[6.134,-0.032],[6.161,-0.102],[6.222,-0.163],[6.335,-0.209],[6.467,-0.209],[6.568,-0.154],[6.62,-0.082],[6.624,0.241],[6.651,0.245],[6.657,0.297],[6.68,0.262],[6.719,0.282],[6.746,0.259],[6.774,0.282],[6.801,0.259],[6.828,0.282],[6.859,0.259],[6.883,0.282],[6.902,0.259],[6.933,0.278],[6.972,0.259],[7.036,0.303],[7.036,1.45],[6.998,1.485],[6.962,1.478],[6.947,1.489],[6.908,1.477],[6.865,1.489],[6.853,1.477],[6.822,1.493],[6.799,1.477],[6.764,1.493],[6.744,1.477],[6.713,1.493],[6.678,1.458],[6.634,1.463],[6.633,1.899],[6.648,2.012],[6.627,2.1],[6.183,2.099],[6.107,2.07],[6.093,1.982],[5.992,1.982],[5.969,2.099],[5.871,2.103],[5.794,2.102],[5.723,2.075],[5.712,1.986],[5.591,1.985],[5.576,2.098],[5.463,2.102],[5.396,2.102],[5.338,2.078],[5.323,1.985],[5.194,1.985],[5.176,2.1],[5.12,2.101],[4.995,2.101],[4.943,2.072],[4.929,1.984],[4.809,1.984],[4.787,1.994],[4.774,2.105],[4.606,2.104],[4.579,2.093],[4.554,2.071],[4.54,1.988],[4.396,1.987],[4.376,2.104],[4.201,2.104],[4.164,2.075],[4.155,1.987],[3.999,1.987],[3.983,2.103],[3.8,2.103],[3.775,2.078],[3.769,1.99],[3.594,1.99],[3.586,2.103],[3.407,2.106],[3.386,2.077],[3.384,2.028],[3.401,2.073],[3.396,1.99],[3.193,1.989],[3.185,2.106],[3.006,2.106],[3.002,1.993],[2.8,1.989],[2.784,2.105],[2.621,2.109],[2.603,2.103],[2.603,1.994],[2.555,1.988],[2.395,1.992],[2.393,2.099],[2.379,2.109],[2.212,2.108],[2.202,1.997],[2.122,1.991],[1.998,1.991],[1.996,2.094],[1.982,2.108],[1.811,2.108],[1.805,2.004],[1.788,1.991],[1.593,1.994],[1.593,2.01],[1.61,2.004],[1.61,2.078],[1.589,2.107],[1.41,2.107],[1.394,1.99],[1.223,1.99],[1.207,2.091],[1.188,2.107],[1.083,2.11],[-0.467,2.108],[-0.587,2.096],[-0.589,1.931],[-0.505,1.909],[-0.498,1.894],[0.013,1.891],[0.069,1.83],[0.069,1.675],[-0.014,1.591]],"left":[[-0.723,1.033],[-0.71,0.793],[-0.628,0.577],[-0.472,0.399],[-0.254,0.264],[-0.246,-0.149],[-0.23,-0.228],[-0.012,-0.237],[0.197,-0.237],[0.246,-0.188],[0.257,-0.113],[0.249,0.19],[0.263,0.196],[2.895,0.195],[2.974,0.18],[4.349,0.17],[6.141,0.188],[6.139,-0.022],[6.218,-0.16],[6.303,-0.221],[6.428,-0.232],[6.55,-0.185],[6.615,-0.096],[6.614,0.194],[6.638,0.21],[6.64,0.291],[6.675,0.291],[6.695,0.255],[6.726,0.279],[6.762,0.256],[6.785,0.279],[6.801,0.256],[6.821,0.256],[6.84,0.279],[6.856,0.256],[6.876,0.256],[6.895,0.279],[6.911,0.256],[6.931,0.256],[6.95,0.279],[6.966,0.256],[6.986,0.256],[7.058,0.309],[7.093,0.447],[7.113,0.714],[7.104,1.193],[7.068,1.425],[7,1.494],[6.972,1.47],[6.941,1.497],[6.921,1.466],[6.886,1.497],[6.866,1.466],[6.831,1.497],[6.811,1.466],[6.776,1.497],[6.752,1.466],[6.732,1.497],[6.717,1.497],[6.697,1.462],[6.636,1.464],[6.647,2.029],[6.643,2.065],[6.574,2.114],[6.134,2.113],[6.125,2.017],[6.107,1.999],[5.977,1.999],[5.971,2.064],[5.914,2.113],[5.741,2.113],[5.728,2.005],[5.628,1.999],[5.571,2.004],[5.571,2.059],[5.525,2.112],[5.349,2.112],[5.339,2.008],[5.325,1.998],[5.172,2.002],[5.166,2.063],[5.128,2.112],[4.952,2.112],[4.946,2.007],[4.905,1.998],[4.771,1.997],[4.765,2.062],[4.736,2.111],[4.559,2.111],[4.553,2.003],[4.457,1.997],[4.366,2.001],[4.36,2.066],[4.339,2.111],[4.166,2.11],[4.16,2.014],[4.17,2.063],[4.176,2.006],[4.095,2],[3.962,2],[3.946,2.11],[3.773,2.11],[3.769,2],[3.616,1.996],[3.559,1.998],[3.553,2.11],[3.38,2.109],[3.368,1.999],[3.258,1.995],[3.158,2.001],[3.16,2.109],[2.983,2.109],[2.96,1.995],[2.775,1.999],[2.763,2.109],[2.59,2.108],[2.569,2.063],[2.565,2],[2.48,1.998],[2.384,2],[2.374,2.108],[2.201,2.108],[2.168,2.063],[2.164,2],[2.123,1.998],[1.993,1.998],[1.977,2.107],[1.808,2.107],[1.767,2.062],[1.763,1.999],[1.75,1.993],[1.604,1.997],[1.588,2.107],[1.415,2.107],[1.366,2.061],[1.357,1.993],[1.215,1.993],[1.191,2.106],[-0.062,2.105],[-0.577,2.088],[-0.618,2.074],[-0.618,1.992],[-0.614,1.906],[-0.58,1.896],[-0.569,1.868],[-0.046,1.865],[0.043,1.781],[0.047,1.631],[0.006,1.594],[-0.592,1.597],[-0.609,1.587],[-0.615,1.55],[-0.678,1.546]]},"features":{"side":{"forward_assist_housing":[[[-0.543,1.234],[0.489,1.232],[1.111,1.213],[1.267,1.174],[1.423,1.105],[1.54,1.019],[1.618,0.93],[1.657,0.864],[1.618,0.774],[1.541,0.676],[1.424,0.606],[1.268,0.559],[0.879,0.527],[0.1,0.526],[-0.445,0.533],[-0.562,0.564],[-0.659,0.673],[-0.69,0.829],[-0.695,0.984],[-0.679,1.101],[-0.633,1.187]]],"forward_assist_bore":[[[-0.644,1.148],[-0.477,1.148],[-0.476,0.615],[-0.643,0.615]]],"deflector":[[[2.045,1.658],[2.103,1.697],[2.863,1.71],[2.933,1.574],[2.98,1.419],[2.988,1.068],[2.961,0.881],[2.767,0.873],[2.066,0.872],[2.031,0.93]]],"deflector_crest":[[[2.318,1.671],[2.395,1.671],[2.396,1.145],[2.318,1.145]]],"port":[[[2.98,1.38],[6.087,1.385],[6.088,0.847],[2.981,0.842]]],"hinge_rear":[[[2.786,0.795],[2.961,0.796],[2.962,0.515],[2.787,0.515]]],"hinge_front":[[[6.181,0.801],[6.348,0.801],[6.349,0.521],[6.182,0.521]]]},"left":{"cam_pin_pad":[[[5.668,1.462],[5.628,1.572],[5.53,1.619],[4.685,1.618],[4.587,1.571],[4.548,1.461],[4.548,1.205],[4.588,1.107],[4.686,1.06],[5.531,1.061],[5.629,1.109],[5.668,1.207]]],"latch_slot":[[[0.371,1.828],[0.343,1.895],[0.284,1.919],[0.225,1.895],[0.198,1.828],[0.198,1.592],[0.226,1.526],[0.285,1.502],[0.344,1.526],[0.371,1.593]]]}},"placement":{"side":{"plane":"xy","offset":{}},"left":{"plane":"xy","offset":{}}},"bounds":{"min":[-0.621,-0.2113,-0.6938],"max":[7.036,2.092,1.4182]},"volume_in3":4.7621,"centroid":[2.9753,1.009,0.091],"shell":[3.0371,1.0772,0.0528],"area_in2":81.9079,"triangles":14648,"manifold":true,"rear_corner":{"r":0.75,"centre":[0.122,0.9985],"x":[-0.628,0.122],"outside_z":0.2472},"slabs":[[-0.621,0.249,-0.694,-0.238,2.092,1.418],[-0.238,-0.211,-0.59,0.145,2.092,1.365],[0.145,-0.211,-0.59,0.528,2.092,1.226],[0.528,0.249,-0.59,0.91,1.974,1.087],[0.91,0.249,-0.59,1.293,1.974,0.947],[1.293,0.249,-0.59,1.676,1.974,0.808],[1.676,0.249,-0.59,2.059,1.974,0.59],[2.059,0.249,-0.59,2.442,1.974,1.25],[2.442,0.249,-0.59,2.825,1.974,1.168],[2.825,0.249,-0.59,3.207,1.974,0.911],[3.207,0.249,-0.59,5.887,1.974,0.589],[5.887,-0.178,-0.59,6.27,1.974,0.826],[6.27,-0.2,-0.622,6.653,1.974,0.622],[6.653,0.255,-0.622,7.036,1.5,0.622]],"slots":["receiver"]},"faxon-16-pencil-barrel":{"part":"faxon-16-pencil-barrel","model":"faxon-16-pencil-barrel.glb","script":"faxon_16_pencil_barrel.py","inputs":{"faxon-16-pencil-barrel.bore_d":0.219,"faxon-16-pencil-barrel.chamber_front_x":0.794,"faxon-16-pencil-barrel.chamber_od":0.98,"faxon-16-pencil-barrel.collar_od":0.755,"faxon-16-pencil-barrel.collar_rear_x":8.668,"faxon-16-pencil-barrel.extension_lug_bore_d":0.572,"faxon-16-pencil-barrel.extension_lug_depth":0.214,"faxon-16-pencil-barrel.extension_mouth_chamfer":0.045,"faxon-16-pencil-barrel.extension_mouth_d":0.77,"faxon-16-pencil-barrel.extension_od":0.999,"faxon-16-pencil-barrel.extension_rear_x":-0.976,"faxon-16-pencil-barrel.extension_recess_d":0.83,"faxon-16-pencil-barrel.extension_recess_depth":0.595,"faxon-16-pencil-barrel.flange_front_x":0.109,"faxon-16-pencil-barrel.flange_od":1.163,"faxon-16-pencil-barrel.forward_od":0.502,"faxon-16-pencil-barrel.forward_rear_x":10.181,"faxon-16-pencil-barrel.gas_port_d":0.081,"faxon-16-pencil-barrel.gas_port_x":9.137,"faxon-16-pencil-barrel.index_pin_d":0.12525,"faxon-16-pencil-barrel.index_pin_top":0.546,"faxon-16-pencil-barrel.index_pin_x":0.111,"faxon-16-pencil-barrel.journal_front_x":9.96,"faxon-16-pencil-barrel.journal_od":0.625,"faxon-16-pencil-barrel.journal_rear_x":8.847,"faxon-16-pencil-barrel.muzzle_od":0.615,"faxon-16-pencil-barrel.muzzle_ring_foot_x":14.704,"faxon-16-pencil-barrel.muzzle_ring_rear_x":14.917,"faxon-16-pencil-barrel.outline_front_face":16.804,"faxon-16-pencil-barrel.outline_rear_face":0.103,"faxon-16-pencil-barrel.overall_length":16.631,"faxon-16-pencil-barrel.shoulder_x":15.03,"faxon-16-pencil-barrel.taper_front_od":0.525,"faxon-16-pencil-barrel.taper_front_x":8.377,"faxon-16-pencil-barrel.taper_rear_od":0.618,"faxon-16-pencil-barrel.taper_rear_x":1.798,"faxon-16-pencil-barrel.thread_length":0.625,"faxon-16-pencil-barrel.thread_major_d":0.4957,"faxon-16-pencil-barrel.thread_minor_d":0.4551,"faxon-16-pencil-barrel.thread_pitch":0.03571},"profiles":{"side":[[0.103,0.49],[0.103,-0.481],[0.114,-0.49],[0.911,-0.49],[0.92,-0.499],[0.939,-0.49],[1.021,-0.49],[1.035,-0.504],[1.053,-0.559],[1.085,-0.582],[1.204,-0.582],[1.236,-0.549],[1.255,-0.495],[1.287,-0.481],[1.625,-0.481],[1.644,-0.49],[1.653,-0.481],[1.864,-0.481],[1.873,-0.49],[1.882,-0.481],[1.983,-0.472],[1.992,-0.462],[2.047,-0.462],[2.092,-0.444],[2.303,-0.417],[2.358,-0.398],[2.404,-0.398],[2.459,-0.38],[2.56,-0.371],[2.605,-0.353],[2.66,-0.353],[2.669,-0.343],[2.77,-0.334],[2.825,-0.316],[2.889,-0.316],[2.898,-0.307],[4.244,-0.307],[4.263,-0.298],[4.281,-0.307],[4.29,-0.298],[5.664,-0.298],[5.673,-0.288],[5.682,-0.298],[5.728,-0.298],[5.746,-0.288],[5.755,-0.298],[5.82,-0.298],[5.829,-0.288],[6.992,-0.288],[7.001,-0.279],[9.538,-0.27],[9.547,-0.279],[9.583,-0.279],[9.666,-0.307],[9.684,-0.325],[9.702,-0.325],[9.73,-0.343],[9.766,-0.38],[9.803,-0.38],[9.812,-0.389],[9.849,-0.389],[9.867,-0.38],[9.876,-0.389],[9.95,-0.389],[9.972,-0.357],[9.963,-0.348],[9.963,-0.321],[9.977,-0.307],[9.995,-0.316],[11.094,-0.316],[11.158,-0.279],[11.222,-0.27],[11.232,-0.261],[15.838,-0.261],[15.847,-0.27],[15.939,-0.279],[15.994,-0.298],[16.039,-0.325],[16.168,-0.325],[16.19,-0.284],[16.195,-0.243],[16.232,-0.243],[16.241,-0.252],[16.25,-0.243],[16.259,-0.261],[16.277,-0.261],[16.287,-0.243],[16.314,-0.261],[16.323,-0.243],[16.332,-0.261],[16.351,-0.261],[16.36,-0.243],[16.378,-0.261],[16.396,-0.243],[16.406,-0.261],[16.415,-0.261],[16.433,-0.243],[16.438,-0.256],[16.451,-0.261],[16.47,-0.243],[16.479,-0.261],[16.488,-0.261],[16.506,-0.243],[16.516,-0.261],[16.543,-0.252],[16.561,-0.261],[16.58,-0.243],[16.589,-0.261],[16.607,-0.252],[16.635,-0.261],[16.653,-0.252],[16.671,-0.261],[16.69,-0.252],[16.708,-0.261],[16.726,-0.252],[16.744,-0.261],[16.763,-0.252],[16.781,-0.261],[16.804,-0.243],[16.804,0.22],[16.763,0.234],[16.735,0.224],[16.717,0.234],[16.708,0.224],[16.68,0.234],[16.662,0.224],[16.644,0.234],[16.635,0.224],[16.607,0.234],[16.598,0.224],[16.57,0.234],[16.561,0.224],[16.534,0.234],[16.525,0.224],[16.497,0.234],[16.488,0.224],[16.461,0.234],[16.451,0.224],[16.424,0.234],[16.415,0.224],[16.387,0.234],[16.378,0.224],[16.351,0.234],[16.342,0.224],[16.323,0.234],[16.305,0.224],[16.277,0.234],[16.222,0.206],[16.204,0.206],[16.19,0.22],[16.19,0.266],[16.168,0.298],[16.039,0.298],[16.021,0.279],[15.948,0.252],[15.847,0.243],[15.838,0.234],[15.059,0.234],[15.05,0.243],[14.913,0.234],[14.904,0.243],[11.25,0.243],[11.241,0.252],[11.204,0.252],[11.149,0.27],[11.076,0.307],[10.005,0.307],[9.977,0.298],[9.963,0.311],[9.959,0.371],[9.785,0.371],[9.739,0.334],[9.666,0.298],[9.647,0.298],[9.592,0.27],[9.501,0.261],[9.492,0.252],[9.455,0.252],[9.446,0.261],[9.391,0.252],[9.382,0.261],[8.246,0.261],[8.237,0.27],[6.342,0.279],[6.332,0.288],[5.169,0.288],[5.16,0.298],[2.898,0.307],[2.889,0.316],[2.825,0.316],[2.779,0.334],[2.724,0.334],[2.715,0.343],[2.679,0.343],[2.624,0.362],[2.578,0.362],[2.569,0.371],[2.523,0.371],[2.514,0.38],[2.459,0.38],[2.413,0.398],[2.367,0.398],[2.312,0.417],[2.212,0.426],[2.157,0.444],[2.056,0.453],[2.01,0.472],[1.909,0.481],[1.9,0.49],[1.259,0.49],[1.236,0.531],[1.236,0.549],[1.204,0.582],[1.076,0.582],[1.053,0.559],[1.039,0.508],[0.92,0.508],[0.884,0.49],[0.865,0.499],[0.856,0.49],[0.517,0.49],[0.462,0.49],[0.453,0.499],[0.444,0.49],[0.435,0.499],[0.426,0.49],[0.417,0.499],[0.408,0.49],[0.334,0.49],[0.325,0.499],[0.316,0.49],[0.307,0.499],[0.298,0.49],[0.288,0.499],[0.279,0.49],[0.27,0.499],[0.261,0.49],[0.188,0.49],[0.179,0.499],[0.169,0.49]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"x":"extension_rear_x"}}},"bounds":{"min":[-0.976,-0.5815,-0.5815],"max":[15.655,0.5815,0.5815]},"volume_in3":4.3726,"centroid":[5.3781,0.0003,0],"shell":[6.1731,0.0013,0],"area_in2":48.9502,"triangles":19670,"manifold":true,"slabs":[[-0.976,-0.5,-0.5,-0.144,0.546,0.5],[-0.144,-0.581,-0.581,0.271,0.581,0.581],[0.271,-0.49,-0.49,1.103,0.49,0.49],[1.103,-0.434,-0.434,1.519,0.434,0.434],[1.519,-0.359,-0.359,1.934,0.359,0.359],[1.934,-0.318,-0.318,8.587,0.318,0.318],[8.587,-0.377,-0.377,9.003,0.377,0.377],[9.003,-0.313,-0.313,10.25,0.313,0.313],[10.25,-0.308,-0.308,15.239,0.308,0.308],[15.239,-0.248,-0.248,15.655,0.248,0.248]],"slots":["barrel","extension","pin"]},"fn-p90-50-magazine":{"part":"fn-p90-50-magazine","model":"fn-p90-50-magazine.glb","script":"fn_p90_50_magazine.py","inputs":{"fn-p90-50-magazine.cap_above":0.17,"fn-p90-50-magazine.cap_below":0.22,"fn-p90-50-magazine.cap_foot_slope":48,"fn-p90-50-magazine.cap_length":0.45,"fn-p90-50-magazine.cap_lug_length":0.6,"fn-p90-50-magazine.cap_lug_width":0.5,"fn-p90-50-magazine.cap_panel_depth":0.02,"fn-p90-50-magazine.cap_panel_frame":0.07,"fn-p90-50-magazine.cap_width":2.04,"fn-p90-50-magazine.edge_radius":0.15,"fn-p90-50-magazine.height":0.77,"fn-p90-50-magazine.length":10.869,"fn-p90-50-magazine.lip_bar_width":0.72,"fn-p90-50-magazine.pocket_depth":0.12,"fn-p90-50-magazine.pocket_rim":0.12,"fn-p90-50-magazine.rib_drop":0.08,"fn-p90-50-magazine.rib_from_face":0.55,"fn-p90-50-magazine.rib_length":0.25,"fn-p90-50-magazine.rib_span":1.5,"fn-p90-50-magazine.ring_bore_depth":0.1,"fn-p90-50-magazine.ring_height":0.03,"fn-p90-50-magazine.ring_id":0.3,"fn-p90-50-magazine.ring_od":0.45,"fn-p90-50-magazine.slot_width":0.313,"fn-p90-50-magazine.tower_d":1.873,"fn-p90-50-magazine.tower_drop":0.473,"fn-p90-50-magazine.width":1.949},"profiles":{},"bounds":{"min":[0,-0.473,-1.02],"max":[10.869,0.94,1.02]},"volume_in3":17.0522,"centroid":[5.3393,0.3493,0],"shell":[4.6145,0.3488,0],"area_in2":78.2236,"triangles":7728,"manifold":true,"slabs":[[0,-0.473,-0.778,0.388,0.77,0.778],[0.388,-0.473,-0.975,1.941,0.77,0.975],[1.941,-0.047,-0.975,10.093,0.77,0.975],[10.093,-0.22,-1.02,10.869,0.94,1.02]],"slots":["body","tower"]},"geissele-139-chf-barrel":{"part":"geissele-139-chf-barrel","model":"geissele-139-chf-barrel.glb","script":"geissele_139_chf_barrel.py","inputs":{"geissele-139-chf-barrel.bore_d":0.219,"geissele-139-chf-barrel.chamber_front_x":0.916,"geissele-139-chf-barrel.chamber_od":0.979,"geissele-139-chf-barrel.collar_od":0.842,"geissele-139-chf-barrel.collar_rear_x":8.748,"geissele-139-chf-barrel.extension_lug_bore_d":0.572,"geissele-139-chf-barrel.extension_lug_depth":0.214,"geissele-139-chf-barrel.extension_mouth_chamfer":0.045,"geissele-139-chf-barrel.extension_mouth_d":0.77,"geissele-139-chf-barrel.extension_od":0.999,"geissele-139-chf-barrel.extension_rear_x":-0.989,"geissele-139-chf-barrel.extension_recess_d":0.83,"geissele-139-chf-barrel.extension_recess_depth":0.595,"geissele-139-chf-barrel.flange_front_x":0.117,"geissele-139-chf-barrel.flange_od":1.167,"geissele-139-chf-barrel.gas_port_d":0.081,"geissele-139-chf-barrel.gas_port_x":9.177,"geissele-139-chf-barrel.index_pin_d":0.12525,"geissele-139-chf-barrel.index_pin_protrusion":0.094,"geissele-139-chf-barrel.index_pin_x":0.077,"geissele-139-chf-barrel.journal_front_x":9.933,"geissele-139-chf-barrel.journal_od":0.75,"geissele-139-chf-barrel.journal_rear_x":8.887,"geissele-139-chf-barrel.muzzle_od":0.701,"geissele-139-chf-barrel.muzzle_ring_foot_x":12.487,"geissele-139-chf-barrel.muzzle_ring_rear_x":12.57,"geissele-139-chf-barrel.muzzle_run_od":0.67,"geissele-139-chf-barrel.muzzle_run_rear_x":10.59,"geissele-139-chf-barrel.outline_axis_x":7.22,"geissele-139-chf-barrel.outline_extension_od":0.9854,"geissele-139-chf-barrel.outline_extension_x":0.542,"geissele-139-chf-barrel.outline_front_face":14.406,"geissele-139-chf-barrel.outline_journal_x":10.41,"geissele-139-chf-barrel.outline_rear_face":0.184,"geissele-139-chf-barrel.overall_length":14.401,"geissele-139-chf-barrel.shoulder_x":12.792,"geissele-139-chf-barrel.taper_front_od":0.665,"geissele-139-chf-barrel.taper_front_x":8.276,"geissele-139-chf-barrel.taper_rear_od":0.726,"geissele-139-chf-barrel.taper_rear_x":2.324,"geissele-139-chf-barrel.thread_length":0.62,"geissele-139-chf-barrel.thread_major_d":0.4957,"geissele-139-chf-barrel.thread_minor_d":0.4551,"geissele-139-chf-barrel.thread_pitch":0.03571},"profiles":{"side":[[0.184,0.483],[0.184,-0.497],[0.983,-0.497],[0.99,-0.49],[1.041,-0.49],[1.088,-0.551],[1.127,-0.576],[1.264,-0.576],[1.307,-0.555],[1.365,-0.483],[1.984,-0.49],[1.992,-0.483],[2.1,-0.483],[2.172,-0.468],[2.258,-0.468],[2.381,-0.447],[2.445,-0.447],[2.453,-0.439],[2.64,-0.432],[2.647,-0.425],[2.87,-0.411],[2.928,-0.396],[2.993,-0.396],[3,-0.389],[3.324,-0.367],[3.331,-0.36],[3.439,-0.36],[3.447,-0.353],[7.329,-0.339],[7.336,-0.331],[8.359,-0.331],[8.366,-0.324],[8.424,-0.324],[8.431,-0.331],[9,-0.331],[9.008,-0.324],[9.188,-0.324],[9.195,-0.331],[9.288,-0.331],[9.296,-0.339],[9.368,-0.339],[9.375,-0.346],[9.519,-0.36],[9.721,-0.418],[9.879,-0.418],[9.908,-0.367],[11.017,-0.375],[11.024,-0.367],[11.168,-0.36],[11.176,-0.353],[11.478,-0.346],[11.485,-0.339],[12.847,-0.339],[12.861,-0.331],[12.868,-0.339],[13.473,-0.339],[13.524,-0.353],[13.79,-0.36],[13.823,-0.335],[13.844,-0.285],[13.87,-0.259],[13.891,-0.252],[13.956,-0.252],[13.963,-0.259],[13.97,-0.252],[13.985,-0.259],[14.129,-0.252],[14.136,-0.259],[14.23,-0.259],[14.237,-0.252],[14.251,-0.259],[14.259,-0.252],[14.302,-0.252],[14.309,-0.259],[14.395,-0.259],[14.406,-0.252],[14.406,0.234],[14.388,0.245],[13.891,0.245],[13.87,0.252],[13.837,0.285],[13.823,0.328],[13.805,0.346],[13.553,0.346],[13.488,0.331],[11.86,0.339],[11.853,0.331],[11.774,0.331],[11.766,0.339],[11.471,0.339],[11.464,0.346],[11.082,0.367],[11.075,0.375],[9.915,0.382],[9.908,0.375],[9.897,0.407],[9.879,0.425],[9.728,0.425],[9.526,0.367],[9.382,0.353],[9.375,0.346],[9.288,0.346],[9.281,0.339],[6.926,0.346],[6.919,0.353],[5.161,0.353],[5.154,0.36],[3.447,0.36],[3.439,0.367],[3.324,0.367],[3.317,0.375],[3.007,0.396],[2.928,0.411],[2.784,0.418],[2.777,0.425],[2.705,0.425],[2.698,0.432],[2.611,0.432],[2.539,0.447],[2.381,0.454],[2.373,0.461],[2.273,0.461],[2.265,0.468],[2.136,0.475],[2.064,0.49],[1.372,0.483],[1.286,0.569],[1.264,0.576],[1.134,0.576],[1.098,0.555],[1.048,0.49],[0.846,0.49],[0.191,0.49]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"x":"extension_rear_x"}}},"bounds":{"min":[-0.989,-0.5835,-0.5835],"max":[13.412,0.5935,0.5835]},"volume_in3":5.6837,"centroid":[5.2475,0.0001,0],"shell":[5.5486,0.0008,0],"area_in2":47.5278,"triangles":14638,"manifold":true,"slabs":[[-0.989,-0.5,-0.5,-0.211,0.5,0.5],[-0.211,-0.584,-0.584,0.179,0.594,0.584],[0.179,-0.489,-0.489,1.736,0.489,0.489],[1.736,-0.416,-0.416,2.514,0.416,0.416],[2.514,-0.362,-0.362,8.352,0.362,0.362],[8.352,-0.421,-0.421,10.298,0.421,0.421],[10.298,-0.353,-0.353,13.023,0.353,0.353],[13.023,-0.248,-0.248,13.412,0.248,0.248]],"slots":["barrel"]},"geissele-145-chf-barrel":{"part":"geissele-145-chf-barrel","model":"geissele-145-chf-barrel.glb","script":"geissele_145_chf_barrel.py","inputs":{"geissele-145-chf-barrel.bore_d":0.219,"geissele-145-chf-barrel.chamber_front_x":0.962,"geissele-145-chf-barrel.chamber_od":0.983,"geissele-145-chf-barrel.collar_od":0.844,"geissele-145-chf-barrel.collar_rear_x":8.743,"geissele-145-chf-barrel.extension_lug_bore_d":0.572,"geissele-145-chf-barrel.extension_lug_depth":0.214,"geissele-145-chf-barrel.extension_mouth_chamfer":0.045,"geissele-145-chf-barrel.extension_mouth_d":0.77,"geissele-145-chf-barrel.extension_od":0.999,"geissele-145-chf-barrel.extension_rear_x":-1.001,"geissele-145-chf-barrel.extension_recess_d":0.83,"geissele-145-chf-barrel.extension_recess_depth":0.595,"geissele-145-chf-barrel.flange_front_x":0.117,"geissele-145-chf-barrel.flange_od":1.168,"geissele-145-chf-barrel.gas_port_d":0.076,"geissele-145-chf-barrel.gas_port_x":9.168,"geissele-145-chf-barrel.index_pin_d":0.12525,"geissele-145-chf-barrel.index_pin_protrusion":0.094,"geissele-145-chf-barrel.index_pin_x":0.063,"geissele-145-chf-barrel.journal_front_x":9.93,"geissele-145-chf-barrel.journal_od":0.75,"geissele-145-chf-barrel.journal_rear_x":8.882,"geissele-145-chf-barrel.muzzle_od":0.699,"geissele-145-chf-barrel.muzzle_ring_foot_x":13.04,"geissele-145-chf-barrel.muzzle_ring_rear_x":13.141,"geissele-145-chf-barrel.muzzle_run_od":0.666,"geissele-145-chf-barrel.muzzle_run_rear_x":10.545,"geissele-145-chf-barrel.outline_front_face":14.979,"geissele-145-chf-barrel.outline_rear_face":0.069,"geissele-145-chf-barrel.overall_length":15.001,"geissele-145-chf-barrel.shoulder_x":13.381,"geissele-145-chf-barrel.taper_front_od":0.663,"geissele-145-chf-barrel.taper_front_x":8.306,"geissele-145-chf-barrel.taper_rear_od":0.725,"geissele-145-chf-barrel.taper_rear_x":2.334,"geissele-145-chf-barrel.thread_length":0.619,"geissele-145-chf-barrel.thread_major_d":0.4957,"geissele-145-chf-barrel.thread_minor_d":0.4551,"geissele-145-chf-barrel.thread_pitch":0.03571},"profiles":{"side":[[0.069,0.501],[0.069,-0.495],[0.869,-0.5],[0.877,-0.492],[1.019,-0.493],[1.03,-0.542],[1.048,-0.568],[1.086,-0.584],[1.13,-0.584],[1.153,-0.584],[1.194,-0.573],[1.217,-0.498],[1.228,-0.487],[2.067,-0.485],[2.074,-0.478],[2.306,-0.464],[2.314,-0.457],[2.441,-0.45],[2.448,-0.443],[2.606,-0.436],[2.613,-0.429],[2.838,-0.415],[2.845,-0.408],[2.913,-0.408],[2.92,-0.401],[3.167,-0.38],[3.175,-0.372],[3.369,-0.366],[3.377,-0.359],[4.567,-0.359],[4.574,-0.351],[5.195,-0.355],[5.203,-0.348],[5.839,-0.352],[5.847,-0.345],[6.438,-0.348],[6.445,-0.341],[7.081,-0.345],[7.089,-0.338],[7.725,-0.342],[7.733,-0.334],[9.304,-0.329],[9.312,-0.337],[9.371,-0.337],[9.379,-0.345],[9.558,-0.368],[9.752,-0.422],[9.887,-0.423],[9.917,-0.371],[11.018,-0.37],[11.025,-0.363],[11.1,-0.363],[11.107,-0.356],[11.437,-0.343],[11.444,-0.336],[11.527,-0.336],[11.534,-0.329],[12.514,-0.335],[12.522,-0.328],[13.854,-0.329],[14.056,-0.33],[14.108,-0.345],[14.355,-0.347],[14.389,-0.328],[14.404,-0.276],[14.431,-0.25],[14.453,-0.243],[14.513,-0.251],[14.566,-0.236],[14.573,-0.243],[14.603,-0.236],[14.625,-0.244],[14.633,-0.236],[14.64,-0.244],[14.67,-0.237],[14.693,-0.244],[14.708,-0.237],[14.715,-0.244],[14.745,-0.237],[14.768,-0.245],[14.775,-0.237],[14.783,-0.245],[14.813,-0.237],[14.835,-0.245],[14.85,-0.238],[14.857,-0.245],[14.887,-0.238],[14.91,-0.246],[14.925,-0.238],[14.94,-0.246],[14.979,-0.237],[14.979,0.24],[14.958,0.248],[14.898,0.241],[14.89,0.248],[14.868,0.241],[14.838,0.249],[14.831,0.241],[14.816,0.249],[14.801,0.242],[14.771,0.249],[14.763,0.242],[14.748,0.249],[14.718,0.242],[14.696,0.25],[14.688,0.242],[14.629,0.25],[14.614,0.243],[14.606,0.25],[14.546,0.243],[14.524,0.251],[14.509,0.243],[14.456,0.259],[14.449,0.251],[14.427,0.259],[14.401,0.285],[14.393,0.323],[14.367,0.349],[14.113,0.351],[14.075,0.336],[13.986,0.337],[13.978,0.329],[12.766,0.337],[12.758,0.329],[11.845,0.328],[11.838,0.335],[11.419,0.338],[11.411,0.346],[11.284,0.346],[11.277,0.354],[11.157,0.355],[11.149,0.362],[11.03,0.363],[11.022,0.371],[9.93,0.378],[9.915,0.37],[9.893,0.423],[9.75,0.424],[9.72,0.409],[9.541,0.365],[9.503,0.365],[9.406,0.343],[9.353,0.344],[9.346,0.336],[9.248,0.337],[9.241,0.33],[6.36,0.348],[6.352,0.341],[6.315,0.341],[6.308,0.348],[6.023,0.35],[6.016,0.343],[5.799,0.344],[5.761,0.344],[5.754,0.352],[4.833,0.358],[4.826,0.35],[4.661,0.351],[4.324,0.361],[4.317,0.354],[3.441,0.359],[3.434,0.367],[3.187,0.376],[3.18,0.383],[3.112,0.384],[3.105,0.391],[2.693,0.424],[2.686,0.431],[2.611,0.432],[2.604,0.439],[2.529,0.44],[2.522,0.447],[2.424,0.448],[2.417,0.456],[2.26,0.464],[2.252,0.472],[2.162,0.472],[2.088,0.488],[1.227,0.493],[1.201,0.564],[1.183,0.583],[1.063,0.584],[1.044,0.573],[1.029,0.543],[1.029,0.506],[0.995,0.495],[0.726,0.496],[0.696,0.504],[0.666,0.497],[0.614,0.497],[0.606,0.505],[0.576,0.497],[0.254,0.499],[0.247,0.507],[0.21,0.507]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"x":"extension_rear_x"}}},"bounds":{"min":[-1.001,-0.584,-0.584],"max":[14,0.5935,0.584]},"volume_in3":5.8729,"centroid":[5.467,0.0001,0],"shell":[5.8108,0.0007,0],"area_in2":49.1845,"triangles":14626,"manifold":true,"slabs":[[-1.001,-0.5,-0.5,-0.211,0.5,0.5],[-0.211,-0.584,-0.584,0.183,0.594,0.584],[0.183,-0.491,-0.491,1.762,0.491,0.491],[1.762,-0.416,-0.416,2.552,0.416,0.416],[2.552,-0.361,-0.361,8.473,0.361,0.361],[8.473,-0.422,-0.422,10.052,0.422,0.422],[10.052,-0.367,-0.367,13.605,0.367,0.367],[13.605,-0.248,-0.248,14,0.248,0.248]],"slots":["barrel"]},"geissele-16-chf-barrel":{"part":"geissele-16-chf-barrel","model":"geissele-16-chf-barrel.glb","script":"geissele_16_chf_barrel.py","inputs":{"geissele-16-chf-barrel.bore_d":0.219,"geissele-16-chf-barrel.chamber_front_x":0.937,"geissele-16-chf-barrel.chamber_od":0.982,"geissele-16-chf-barrel.collar_od":0.842,"geissele-16-chf-barrel.collar_rear_x":8.678,"geissele-16-chf-barrel.extension_lug_bore_d":0.572,"geissele-16-chf-barrel.extension_lug_depth":0.214,"geissele-16-chf-barrel.extension_mouth_chamfer":0.045,"geissele-16-chf-barrel.extension_mouth_d":0.77,"geissele-16-chf-barrel.extension_od":0.999,"geissele-16-chf-barrel.extension_rear_x":-1,"geissele-16-chf-barrel.extension_recess_d":0.83,"geissele-16-chf-barrel.extension_recess_depth":0.595,"geissele-16-chf-barrel.flange_front_x":0.155,"geissele-16-chf-barrel.flange_od":1.166,"geissele-16-chf-barrel.gas_port_d":0.078,"geissele-16-chf-barrel.gas_port_x":9.079,"geissele-16-chf-barrel.index_pin_d":0.12525,"geissele-16-chf-barrel.index_pin_protrusion":0.094,"geissele-16-chf-barrel.index_pin_x":0.0626,"geissele-16-chf-barrel.journal_front_x":9.793,"geissele-16-chf-barrel.journal_od":0.75,"geissele-16-chf-barrel.journal_rear_x":8.776,"geissele-16-chf-barrel.muzzle_od":0.705,"geissele-16-chf-barrel.muzzle_ring_foot_x":14.508,"geissele-16-chf-barrel.muzzle_ring_rear_x":14.67,"geissele-16-chf-barrel.muzzle_run_od":0.667,"geissele-16-chf-barrel.muzzle_run_rear_x":10.5,"geissele-16-chf-barrel.outline_extension_od":0.9735,"geissele-16-chf-barrel.outline_extension_x":0.576,"geissele-16-chf-barrel.outline_front_face":16.395,"geissele-16-chf-barrel.outline_journal_x":10.222,"geissele-16-chf-barrel.outline_rear_face":0.136,"geissele-16-chf-barrel.overall_length":16.501,"geissele-16-chf-barrel.shoulder_x":14.845,"geissele-16-chf-barrel.taper_front_od":0.665,"geissele-16-chf-barrel.taper_front_x":8.21,"geissele-16-chf-barrel.taper_rear_od":0.728,"geissele-16-chf-barrel.taper_rear_x":2.32,"geissele-16-chf-barrel.thread_length":0.656,"geissele-16-chf-barrel.thread_major_d":0.4957,"geissele-16-chf-barrel.thread_minor_d":0.4551,"geissele-16-chf-barrel.thread_pitch":0.03571},"profiles":{"side":[[0.136,0.473],[0.136,-0.471],[0.143,-0.478],[0.167,-0.486],[0.987,-0.488],[1.061,-0.562],[1.094,-0.562],[1.102,-0.57],[1.217,-0.57],[1.266,-0.521],[1.299,-0.48],[2.004,-0.481],[2.012,-0.473],[2.111,-0.473],[2.119,-0.465],[2.193,-0.465],[2.201,-0.457],[2.275,-0.457],[2.283,-0.449],[2.463,-0.441],[2.472,-0.433],[2.537,-0.433],[2.545,-0.425],[2.627,-0.425],[2.636,-0.417],[2.709,-0.417],[2.718,-0.409],[2.964,-0.393],[2.972,-0.385],[3.144,-0.377],[3.152,-0.368],[3.308,-0.36],[3.316,-0.352],[3.447,-0.361],[3.62,-0.353],[3.628,-0.361],[3.685,-0.361],[3.693,-0.353],[4.768,-0.355],[4.776,-0.347],[5.055,-0.355],[5.063,-0.347],[6.342,-0.349],[6.35,-0.341],[7.555,-0.343],[7.564,-0.335],[8.753,-0.337],[8.777,-0.329],[8.794,-0.337],[8.933,-0.338],[8.941,-0.329],[9.138,-0.33],[9.146,-0.338],[9.212,-0.338],[9.22,-0.346],[9.343,-0.363],[9.564,-0.421],[9.728,-0.421],[9.732,-0.376],[9.745,-0.364],[9.761,-0.372],[10.86,-0.374],[10.868,-0.366],[10.958,-0.366],[10.966,-0.358],[11.335,-0.342],[11.344,-0.334],[12.147,-0.335],[12.155,-0.327],[12.336,-0.335],[12.5,-0.336],[12.508,-0.328],[12.967,-0.337],[13.025,-0.337],[13.033,-0.328],[13.18,-0.329],[13.189,-0.337],[13.221,-0.337],[13.23,-0.329],[14.197,-0.33],[14.205,-0.339],[14.296,-0.339],[14.337,-0.339],[14.345,-0.331],[15.517,-0.333],[15.566,-0.349],[15.804,-0.35],[15.837,-0.342],[15.858,-0.321],[15.866,-0.288],[15.895,-0.26],[15.936,-0.243],[15.952,-0.252],[15.968,-0.243],[15.993,-0.252],[16.001,-0.243],[16.395,-0.244],[16.395,0.248],[16.379,0.24],[16.297,0.24],[16.289,0.248],[16.264,0.24],[16.256,0.248],[16.24,0.24],[16.223,0.248],[16.191,0.24],[16.182,0.248],[16.174,0.24],[16.15,0.248],[16.141,0.24],[16.092,0.24],[16.084,0.248],[16.059,0.24],[16.051,0.248],[16.027,0.24],[16.018,0.248],[15.986,0.24],[15.977,0.249],[15.92,0.24],[15.896,0.249],[15.867,0.277],[15.859,0.31],[15.822,0.347],[15.617,0.348],[15.609,0.339],[15.477,0.331],[15.469,0.323],[15.436,0.323],[15.428,0.332],[15.289,0.332],[14.674,0.333],[14.666,0.325],[14.617,0.325],[14.477,0.325],[14.469,0.333],[14.133,0.334],[14.125,0.326],[14.116,0.334],[13.657,0.335],[13.649,0.326],[13.493,0.327],[13.469,0.335],[13.46,0.327],[13.444,0.335],[13.264,0.335],[13.141,0.336],[13.132,0.327],[13.042,0.328],[13.034,0.336],[12.657,0.328],[12.632,0.336],[12.599,0.328],[12.591,0.337],[12.427,0.337],[12.312,0.337],[12.304,0.329],[12.181,0.329],[12.173,0.337],[12.148,0.329],[12.14,0.337],[12.107,0.329],[11.935,0.329],[11.919,0.338],[11.911,0.33],[11.607,0.33],[11.599,0.338],[11.287,0.339],[11.279,0.347],[11.132,0.347],[11.124,0.355],[10.976,0.356],[10.968,0.364],[10.845,0.364],[10.837,0.372],[9.771,0.374],[9.746,0.366],[9.734,0.378],[9.734,0.411],[9.722,0.424],[9.631,0.424],[9.623,0.416],[9.541,0.416],[9.361,0.367],[9.27,0.359],[9.213,0.342],[9.164,0.343],[9.156,0.334],[6.852,0.338],[6.843,0.347],[6.835,0.338],[6.581,0.339],[6.573,0.347],[6.491,0.347],[6.425,0.339],[6.417,0.347],[4.178,0.351],[4.17,0.36],[4.129,0.36],[4.121,0.351],[3.785,0.352],[3.752,0.36],[3.646,0.36],[3.621,0.352],[3.613,0.361],[3.473,0.361],[3.236,0.353],[3.227,0.361],[3.154,0.361],[3.145,0.37],[3.088,0.37],[3.022,0.386],[2.645,0.411],[2.637,0.42],[2.391,0.436],[2.383,0.445],[2.244,0.445],[2.235,0.453],[2.137,0.462],[2.129,0.47],[1.957,0.478],[1.948,0.486],[1.916,0.478],[1.309,0.479],[1.252,0.545],[1.219,0.562],[1.194,0.57],[1.071,0.57],[1.026,0.533],[0.997,0.488],[0.546,0.489],[0.538,0.481],[0.144,0.481]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"x":"extension_rear_x"}}},"bounds":{"min":[-1,-0.583,-0.583],"max":[15.501,0.5935,0.583]},"volume_in3":6.3515,"centroid":[6.1122,0.0001,0],"shell":[6.5235,0.0007,0],"area_in2":53.403,"triangles":15030,"manifold":true,"slabs":[[-1,-0.5,-0.5,-0.175,0.5,0.5],[-0.175,-0.583,-0.583,0.238,0.594,0.583],[0.238,-0.491,-0.491,1.888,0.491,0.491],[1.888,-0.404,-0.404,4.363,0.404,0.404],[4.363,-0.421,-0.421,10.138,0.421,0.421],[10.138,-0.355,-0.355,15.088,0.355,0.355],[15.088,-0.248,-0.248,15.501,0.248,0.248]],"slots":["barrel"]},"geissele-mk16-105-handguard":{"part":"geissele-mk16-105-handguard","model":"geissele-mk16-105-handguard.glb","script":"geissele_mk16_105_handguard.py","inputs":{"geissele-mk16-105-handguard.body_bottom_below_bore":0.86,"geissele-mk16-105-handguard.bottom_flat_width":0.61,"geissele-mk16-105-handguard.channel_roof_below_top":0.18,"geissele-mk16-105-handguard.channel_width":0.47,"geissele-mk16-105-handguard.clamp_gap_width":0.51,"geissele-mk16-105-handguard.cross_bolt_counterbore_d":0.46,"geissele-mk16-105-handguard.cross_bolt_front_below_bore":0.745,"geissele-mk16-105-handguard.cross_bolt_front_from_rear":1.57,"geissele-mk16-105-handguard.cross_bolt_head_d":0.32,"geissele-mk16-105-handguard.cross_bolt_hole_d":0.21,"geissele-mk16-105-handguard.cross_bolt_rear_below_bore":0.835,"geissele-mk16-105-handguard.cross_bolt_rear_from_rear":0.55,"geissele-mk16-105-handguard.height":2.39,"geissele-mk16-105-handguard.inside_diameter":1.26,"geissele-mk16-105-handguard.length":10.505,"geissele-mk16-105-handguard.lower_face_angle":131.4,"geissele-mk16-105-handguard.lower_face_distance":0.794732,"geissele-mk16-105-handguard.mlok_bottom_slot0_x":2.815,"geissele-mk16-105-handguard.mlok_bottom_slots":5,"geissele-mk16-105-handguard.mlok_lower_row_below_bore":0.565,"geissele-mk16-105-handguard.mlok_lower_slots":5,"geissele-mk16-105-handguard.mlok_side_slot0_x":2.815,"geissele-mk16-105-handguard.mlok_side_slots":5,"geissele-mk16-105-handguard.mlok_upper_row_above_bore":0.51,"geissele-mk16-105-handguard.mlok_upper_slot0_x":4.389803,"geissele-mk16-105-handguard.mlok_upper_slots":4,"geissele-mk16-105-handguard.neck_base_above_bore":0.695,"geissele-mk16-105-handguard.neck_chamfer_height":0.08,"geissele-mk16-105-handguard.neck_width":0.61,"geissele-mk16-105-handguard.plate_bar_height":0.2,"geissele-mk16-105-handguard.plate_lobe_d":0.52,"geissele-mk16-105-handguard.rail_front_from_last_slot":0.424,"geissele-mk16-105-handguard.rail_nose_drop":0.09,"geissele-mk16-105-handguard.rail_nose_length":0.23,"geissele-mk16-105-handguard.rail_slot0_from_rear":0.625,"geissele-mk16-105-handguard.rail_slot0_x":0.18,"geissele-mk16-105-handguard.rail_slots":25,"geissele-mk16-105-handguard.rail_top_above_bore":1.2,"geissele-mk16-105-handguard.rear_face_x":-0.445,"geissele-mk16-105-handguard.rear_x":-0.705,"geissele-mk16-105-handguard.side_flat_height":0.6,"geissele-mk16-105-handguard.socket_above_bore":0.585,"geissele-mk16-105-handguard.socket_from_rear":2.77,"geissele-mk16-105-handguard.socket_hole_d":0.31,"geissele-mk16-105-handguard.socket_ring_d":0.545,"geissele-mk16-105-handguard.tab_bottom_below_bore":0.64,"geissele-mk16-105-handguard.tab_length":0.26,"geissele-mk16-105-handguard.tab_screw_d":0.14,"geissele-mk16-105-handguard.tab_top_below_bore":0.27,"geissele-mk16-105-handguard.tongue_bottom_above_bore":0.545,"geissele-mk16-105-handguard.tongue_length":0.12,"geissele-mk16-105-handguard.tongue_top_above_bore":0.727,"geissele-mk16-105-handguard.trough_wall":0.094,"geissele-mk16-105-handguard.trough_width":0.49,"geissele-mk16-105-handguard.upper_face_angle":45,"geissele-mk16-105-handguard.upper_face_distance":0.774282,"geissele-mk16-105-handguard.upper_tab_gap":0.638,"geissele-mk16-105-handguard.width":1.59,"std.mlok.slot_corner_r":0.0937007874015748,"std.mlok.slot_length":1.2598425196850394,"std.mlok.slot_pitch":1.574803149606299,"std.mlok.slot_width":0.2755905511811024,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{"side":[[0,-1.557],[0.006,-1.833],[0.074,-1.874],[0.339,-1.874],[0.383,-1.924],[0.471,-1.952],[0.485,-1.987],[0.485,-2.213],[0.502,-2.302],[0.56,-2.371],[0.648,-2.409],[1.017,-2.409],[1.166,-2.326],[1.227,-2.31],[2.197,-2.31],[2.269,-2.277],[2.434,-2.128],[2.517,-2.084],[2.638,-2.056],[10.566,-2.045],[10.59,-2.021],[10.629,-1.811],[10.673,-1.552],[10.679,-1.42],[10.679,-0.918],[10.607,-0.538],[10.607,-0.223],[10.624,-0.108],[10.406,-0.017],[10.273,0],[10.199,-0.014],[10.188,-0.102],[10.169,-0.116],[10.103,-0.116],[10.089,-0.036],[10.069,-0.017],[9.832,-0.006],[9.813,-0.025],[9.802,-0.108],[9.777,-0.121],[9.703,-0.108],[9.697,-0.036],[9.684,-0.022],[9.502,-0.006],[9.433,-0.019],[9.422,-0.113],[9.408,-0.121],[9.32,-0.121],[9.306,-0.036],[9.287,-0.022],[9.066,-0.011],[9.047,-0.036],[9.033,-0.121],[8.934,-0.127],[8.92,-0.119],[8.914,-0.041],[8.824,-0.011],[8.68,-0.017],[8.661,-0.119],[8.647,-0.127],[8.537,-0.127],[8.523,-0.041],[8.46,-0.017],[8.294,-0.022],[8.286,-0.113],[8.272,-0.127],[8.145,-0.127],[8.137,-0.047],[8.107,-0.028],[7.93,-0.017],[7.906,-0.052],[7.906,-0.119],[7.881,-0.132],[7.76,-0.132],[7.746,-0.047],[7.693,-0.022],[7.545,-0.022],[7.531,-0.036],[7.531,-0.119],[7.511,-0.132],[7.368,-0.132],[7.36,-0.052],[7.346,-0.039],[7.307,-0.022],[7.17,-0.022],[7.156,-0.03],[7.15,-0.124],[7.12,-0.138],[6.977,-0.132],[6.968,-0.047],[6.927,-0.022],[6.784,-0.028],[6.775,-0.124],[6.756,-0.138],[6.591,-0.138],[6.582,-0.052],[6.552,-0.028],[6.403,-0.033],[6.406,-0.124],[6.387,-0.138],[6.205,-0.138],[6.197,-0.052],[6.177,-0.028],[6.028,-0.033],[6.012,-0.138],[5.824,-0.138],[5.808,-0.033],[5.67,-0.028],[5.634,-0.058],[5.626,-0.143],[5.433,-0.132],[5.436,-0.036],[5.405,-0.028],[5.284,-0.033],[5.257,-0.05],[5.246,-0.143],[5.069,-0.138],[5.053,-0.033],[4.904,-0.033],[4.868,-0.058],[4.86,-0.143],[4.7,-0.143],[4.686,-0.124],[4.686,-0.047],[4.672,-0.033],[4.501,-0.044],[4.482,-0.058],[4.474,-0.143],[4.319,-0.138],[4.311,-0.047],[4.297,-0.033],[4.154,-0.033],[4.11,-0.05],[4.096,-0.063],[4.088,-0.143],[3.95,-0.143],[3.936,-0.047],[3.922,-0.033],[3.746,-0.044],[3.71,-0.069],[3.702,-0.143],[3.575,-0.143],[3.553,-0.039],[3.41,-0.033],[3.33,-0.063],[3.311,-0.149],[3.2,-0.143],[3.187,-0.047],[3.167,-0.033],[3.04,-0.033],[2.963,-0.05],[2.944,-0.063],[2.938,-0.141],[2.925,-0.149],[2.825,-0.143],[2.812,-0.047],[2.787,-0.033],[2.583,-0.05],[2.558,-0.069],[2.544,-0.149],[2.451,-0.143],[2.437,-0.052],[2.412,-0.033],[2.186,-0.055],[2.164,-0.149],[2.081,-0.149],[2.048,-0.039],[1.817,-0.05],[1.792,-0.063],[1.772,-0.149],[1.712,-0.149],[1.698,-0.135],[1.673,-0.039],[1.431,-0.05],[1.406,-0.069],[1.392,-0.149],[1.323,-0.141],[1.298,-0.039],[1.034,-0.055],[1.006,-0.149],[0.948,-0.141],[0.923,-0.039],[0.334,-0.05],[0.309,-0.108],[0.309,-0.179],[0.331,-0.256],[0.331,-0.466],[0.311,-0.496],[0.185,-0.502],[0.171,-0.515],[0.138,-0.675],[0.168,-0.7],[0.287,-0.703],[0.243,-0.951],[0.248,-1.497],[0.069,-1.5]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"x":"rear_x","y":"rail_top_above_bore"}}},"bounds":{"min":[-0.705,-1.19,-0.795],"max":[10.06,1.2,0.795]},"volume_in3":7.0921,"centroid":[3.6806,-0.0045,-0.0029],"shell":[4.4078,0.1348,-0.002],"area_in2":127.4271,"triangles":17440,"manifold":true,"slabs":[[-0.705,-0.86,-0.795,-0.306,1.2,0.795],[-0.306,-1.19,-0.795,0.491,1.2,0.795],[0.491,-1.104,-0.795,1.687,1.2,0.795],[1.687,-0.962,-0.795,2.086,1.2,0.795],[2.086,-0.86,-0.795,10.06,1.2,0.795]],"slots":["body","hardware","sockets"]},"geissele-mk16-135-handguard":{"part":"geissele-mk16-135-handguard","model":"geissele-mk16-135-handguard.glb","script":"geissele_mk16_135_handguard.py","inputs":{"geissele-mk16-135-handguard.body_bottom_below_bore":0.86,"geissele-mk16-135-handguard.bottom_flat_width":0.61,"geissele-mk16-135-handguard.channel_roof_below_top":0.18,"geissele-mk16-135-handguard.channel_width":0.47,"geissele-mk16-135-handguard.clamp_gap_width":0.51,"geissele-mk16-135-handguard.cross_bolt_counterbore_d":0.46,"geissele-mk16-135-handguard.cross_bolt_front_below_bore":0.745,"geissele-mk16-135-handguard.cross_bolt_front_from_rear":1.57,"geissele-mk16-135-handguard.cross_bolt_head_d":0.32,"geissele-mk16-135-handguard.cross_bolt_hole_d":0.21,"geissele-mk16-135-handguard.cross_bolt_rear_below_bore":0.835,"geissele-mk16-135-handguard.cross_bolt_rear_from_rear":0.55,"geissele-mk16-135-handguard.height":2.39,"geissele-mk16-135-handguard.inside_diameter":1.26,"geissele-mk16-135-handguard.length":13.52,"geissele-mk16-135-handguard.lower_face_angle":131.4,"geissele-mk16-135-handguard.lower_face_distance":0.794732,"geissele-mk16-135-handguard.mlok_bottom_slot0_x":2.655,"geissele-mk16-135-handguard.mlok_bottom_slots":7,"geissele-mk16-135-handguard.mlok_lower_row_below_bore":0.565,"geissele-mk16-135-handguard.mlok_lower_slots":7,"geissele-mk16-135-handguard.mlok_side_slot0_x":2.655,"geissele-mk16-135-handguard.mlok_side_slots":7,"geissele-mk16-135-handguard.mlok_upper_row_above_bore":0.51,"geissele-mk16-135-handguard.mlok_upper_slot0_x":4.229803,"geissele-mk16-135-handguard.mlok_upper_slots":6,"geissele-mk16-135-handguard.neck_base_above_bore":0.695,"geissele-mk16-135-handguard.neck_chamfer_height":0.08,"geissele-mk16-135-handguard.neck_width":0.61,"geissele-mk16-135-handguard.plate_bar_height":0.2,"geissele-mk16-135-handguard.plate_lobe_d":0.52,"geissele-mk16-135-handguard.rail_front_from_last_slot":0.685,"geissele-mk16-135-handguard.rail_nose_drop":0.11,"geissele-mk16-135-handguard.rail_nose_length":0.29,"geissele-mk16-135-handguard.rail_slot0_from_rear":0.62,"geissele-mk16-135-handguard.rail_slot0_x":0.175,"geissele-mk16-135-handguard.rail_slots":32,"geissele-mk16-135-handguard.rail_top_above_bore":1.2,"geissele-mk16-135-handguard.rear_face_x":-0.445,"geissele-mk16-135-handguard.rear_x":-0.705,"geissele-mk16-135-handguard.side_flat_height":0.6,"geissele-mk16-135-handguard.socket_above_bore":0.585,"geissele-mk16-135-handguard.socket_from_rear":2.77,"geissele-mk16-135-handguard.socket_hole_d":0.31,"geissele-mk16-135-handguard.socket_ring_d":0.545,"geissele-mk16-135-handguard.tab_bottom_below_bore":0.64,"geissele-mk16-135-handguard.tab_length":0.26,"geissele-mk16-135-handguard.tab_screw_d":0.14,"geissele-mk16-135-handguard.tab_top_below_bore":0.27,"geissele-mk16-135-handguard.tongue_bottom_above_bore":0.545,"geissele-mk16-135-handguard.tongue_length":0.12,"geissele-mk16-135-handguard.tongue_top_above_bore":0.727,"geissele-mk16-135-handguard.trough_wall":0.094,"geissele-mk16-135-handguard.trough_width":0.49,"geissele-mk16-135-handguard.upper_face_angle":45,"geissele-mk16-135-handguard.upper_face_distance":0.774282,"geissele-mk16-135-handguard.upper_tab_gap":0.638,"geissele-mk16-135-handguard.width":1.59,"std.mlok.slot_corner_r":0.0937007874015748,"std.mlok.slot_length":1.2598425196850394,"std.mlok.slot_pitch":1.574803149606299,"std.mlok.slot_width":0.2755905511811024,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{"side":[[0,-1.555],[0.007,-1.846],[0.058,-1.883],[0.335,-1.883],[0.383,-1.924],[0.45,-1.944],[0.474,-1.981],[0.474,-2.232],[0.495,-2.313],[0.566,-2.391],[0.647,-2.418],[0.999,-2.418],[1.243,-2.317],[2.219,-2.31],[2.293,-2.269],[2.496,-2.093],[2.652,-2.046],[10.517,-2.032],[13.443,-2.046],[13.474,-2.029],[13.494,-1.981],[13.603,-1.568],[13.616,-1.06],[13.616,-0.965],[13.501,-0.539],[13.508,-0.234],[13.535,-0.173],[13.535,-0.132],[13.504,-0.108],[13.315,-0.041],[13.179,-0.014],[12.841,-0.014],[12.817,-0.119],[12.793,-0.122],[12.759,-0.034],[12.509,-0.007],[12.458,-0.024],[12.438,-0.119],[12.407,-0.122],[12.39,-0.051],[12.366,-0.034],[12.224,-0.007],[12.102,-0.007],[12.078,-0.037],[12.065,-0.119],[12.028,-0.122],[12.004,-0.044],[11.987,-0.034],[11.899,-0.014],[11.723,-0.007],[11.699,-0.051],[11.692,-0.119],[11.642,-0.122],[11.625,-0.051],[11.601,-0.034],[11.526,-0.014],[11.343,-0.007],[11.32,-0.064],[11.32,-0.112],[11.255,-0.122],[11.238,-0.044],[11.222,-0.034],[11.147,-0.014],[10.971,-0.007],[10.954,-0.024],[10.94,-0.119],[10.869,-0.122],[10.842,-0.034],[10.754,-0.007],[10.592,-0.007],[10.568,-0.112],[10.51,-0.122],[10.48,-0.112],[10.473,-0.051],[10.422,-0.02],[10.219,-0.007],[10.202,-0.03],[10.195,-0.112],[10.124,-0.122],[10.094,-0.112],[10.087,-0.044],[10.063,-0.027],[9.989,-0.007],[9.846,-0.007],[9.829,-0.017],[9.823,-0.105],[9.799,-0.122],[9.752,-0.122],[9.707,-0.112],[9.701,-0.044],[9.663,-0.02],[9.616,-0.007],[9.467,-0.007],[9.443,-0.112],[9.372,-0.122],[9.332,-0.115],[9.315,-0.037],[9.25,-0.007],[9.088,-0.007],[9.067,-0.115],[8.945,-0.115],[8.925,-0.034],[8.857,-0.007],[8.783,0],[8.705,-0.01],[8.688,-0.115],[8.559,-0.115],[8.549,-0.044],[8.471,0],[8.336,-0.007],[8.315,-0.115],[8.173,-0.115],[8.163,-0.037],[8.132,-0.014],[8.092,0],[7.963,0],[7.946,-0.112],[7.895,-0.122],[7.787,-0.115],[7.777,-0.037],[7.753,-0.014],[7.699,0],[7.584,-0.007],[7.563,-0.115],[7.401,-0.115],[7.397,-0.044],[7.374,-0.014],[7.326,0],[7.204,-0.007],[7.191,-0.115],[7.022,-0.115],[6.998,-0.017],[6.961,0],[6.832,-0.007],[6.825,-0.115],[6.635,-0.115],[6.618,-0.01],[6.588,0],[6.452,-0.007],[6.439,-0.115],[6.256,-0.115],[6.239,-0.098],[6.239,-0.01],[6.215,0],[6.08,-0.007],[6.053,-0.115],[5.877,-0.115],[5.86,-0.085],[5.856,-0.007],[5.707,0],[5.677,-0.037],[5.67,-0.112],[5.619,-0.122],[5.497,-0.115],[5.487,-0.017],[5.443,0],[5.321,-0.007],[5.291,-0.037],[5.281,-0.115],[5.125,-0.115],[5.108,-0.01],[5.084,0],[4.996,0],[4.915,-0.027],[4.894,-0.115],[4.745,-0.115],[4.735,-0.017],[4.718,0],[4.61,0],[4.542,-0.02],[4.518,-0.037],[4.508,-0.115],[4.373,-0.115],[4.352,-0.007],[4.224,0],[4.132,-0.037],[4.122,-0.115],[4.068,-0.122],[3.993,-0.115],[3.976,-0.01],[3.932,0],[3.824,0],[3.75,-0.034],[3.729,-0.115],[3.614,-0.115],[3.604,-0.017],[3.567,0],[3.424,-0.007],[3.36,-0.037],[3.343,-0.115],[3.235,-0.115],[3.214,-0.007],[3.099,0],[2.977,-0.034],[2.96,-0.112],[2.93,-0.122],[2.862,-0.115],[2.845,-0.017],[2.788,0],[2.679,-0.007],[2.598,-0.034],[2.581,-0.051],[2.571,-0.115],[2.483,-0.115],[2.456,-0.007],[2.286,-0.007],[2.219,-0.027],[2.195,-0.051],[2.185,-0.115],[2.1,-0.112],[2.076,-0.007],[1.907,-0.007],[1.832,-0.027],[1.809,-0.044],[1.792,-0.115],[1.721,-0.112],[1.714,-0.037],[1.69,0],[1.555,-0.007],[1.433,-0.034],[1.409,-0.112],[1.385,-0.122],[1.341,-0.112],[1.318,-0.007],[1.148,-0.007],[1.06,-0.027],[1.03,-0.051],[1.013,-0.122],[0.962,-0.112],[0.948,-0.024],[0.931,-0.007],[0.417,-0.014],[0.335,-0.034],[0.312,-0.085],[0.312,-0.173],[0.332,-0.24],[0.332,-0.45],[0.315,-0.481],[0.183,-0.498],[0.142,-0.647],[0.149,-0.681],[0.173,-0.698],[0.285,-0.708],[0.237,-0.959],[0.244,-1.494],[0.051,-1.504]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"x":"rear_x","y":"rail_top_above_bore"}}},"bounds":{"min":[-0.705,-1.19,-0.795],"max":[13.075,1.2,0.795]},"volume_in3":8.4691,"centroid":[5.0624,0.0278,-0.0024],"shell":[5.8735,0.1506,-0.0016],"area_in2":159.5618,"triangles":21460,"manifold":true,"slabs":[[-0.705,-0.86,-0.795,-0.311,1.2,0.795],[-0.311,-1.19,-0.795,0.476,1.2,0.795],[0.476,-1.123,-0.795,1.657,1.2,0.795],[1.657,-1,-0.795,2.051,1.2,0.795],[2.051,-0.86,-0.795,13.075,1.2,0.795]],"slots":["body","hardware","sockets"]},"geissele-mk16-15-handguard":{"part":"geissele-mk16-15-handguard","model":"geissele-mk16-15-handguard.glb","script":"geissele_mk16_15_handguard.py","inputs":{"geissele-mk16-15-handguard.body_bottom_below_bore":0.86,"geissele-mk16-15-handguard.channel_roof_below_top":0.18,"geissele-mk16-15-handguard.channel_width":0.47,"geissele-mk16-15-handguard.clamp_gap_width":0.51,"geissele-mk16-15-handguard.cross_bolt_counterbore_d":0.46,"geissele-mk16-15-handguard.cross_bolt_front_below_bore":0.745,"geissele-mk16-15-handguard.cross_bolt_front_from_rear":1.57,"geissele-mk16-15-handguard.cross_bolt_head_d":0.32,"geissele-mk16-15-handguard.cross_bolt_hole_d":0.21,"geissele-mk16-15-handguard.cross_bolt_rear_below_bore":0.835,"geissele-mk16-15-handguard.cross_bolt_rear_from_rear":0.55,"geissele-mk16-15-handguard.diag_face_distance":0.774282,"geissele-mk16-15-handguard.height":2.39,"geissele-mk16-15-handguard.inside_diameter":1.26,"geissele-mk16-15-handguard.length":15.12,"geissele-mk16-15-handguard.mlok_bottom_slot0_x":2.635,"geissele-mk16-15-handguard.mlok_bottom_slots":8,"geissele-mk16-15-handguard.mlok_lower_row_below_bore":0.565,"geissele-mk16-15-handguard.mlok_lower_slots":8,"geissele-mk16-15-handguard.mlok_side_slot0_x":2.635,"geissele-mk16-15-handguard.mlok_side_slots":8,"geissele-mk16-15-handguard.mlok_upper_row_above_bore":0.51,"geissele-mk16-15-handguard.mlok_upper_slot0_x":4.209803,"geissele-mk16-15-handguard.mlok_upper_slots":7,"geissele-mk16-15-handguard.neck_base_above_bore":0.695,"geissele-mk16-15-handguard.neck_chamfer_height":0.08,"geissele-mk16-15-handguard.neck_width":0.61,"geissele-mk16-15-handguard.plate_bar_height":0.2,"geissele-mk16-15-handguard.plate_lobe_d":0.52,"geissele-mk16-15-handguard.rail_slot0_x":0.225,"geissele-mk16-15-handguard.rail_slots":36,"geissele-mk16-15-handguard.rail_top_above_bore":1.2,"geissele-mk16-15-handguard.rear_face_x":-0.445,"geissele-mk16-15-handguard.rear_x":-0.705,"geissele-mk16-15-handguard.side_flat_height":0.6,"geissele-mk16-15-handguard.socket_above_bore":0.585,"geissele-mk16-15-handguard.socket_from_rear":2.77,"geissele-mk16-15-handguard.socket_hole_d":0.31,"geissele-mk16-15-handguard.socket_ring_d":0.545,"geissele-mk16-15-handguard.tab_bottom_below_bore":0.64,"geissele-mk16-15-handguard.tab_length":0.26,"geissele-mk16-15-handguard.tab_screw_d":0.14,"geissele-mk16-15-handguard.tab_top_below_bore":0.27,"geissele-mk16-15-handguard.tongue_bottom_above_bore":0.545,"geissele-mk16-15-handguard.tongue_length":0.12,"geissele-mk16-15-handguard.tongue_top_above_bore":0.727,"geissele-mk16-15-handguard.upper_tab_gap":0.638,"geissele-mk16-15-handguard.width":1.59,"std.mlok.slot_corner_r":0.0937007874015748,"std.mlok.slot_length":1.2598425196850394,"std.mlok.slot_pitch":1.574803149606299,"std.mlok.slot_width":0.2755905511811024,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{"side":[[0,-1.538],[0.008,-1.819],[0.065,-1.853],[0.33,-1.853],[0.368,-1.914],[0.467,-1.951],[0.486,-1.978],[0.478,-2.16],[0.509,-2.312],[0.573,-2.377],[0.672,-2.407],[1.052,-2.399],[1.188,-2.324],[1.279,-2.301],[2.251,-2.293],[2.327,-2.263],[2.411,-2.179],[2.434,-2.179],[2.57,-2.096],[2.654,-2.073],[15.107,-2.027],[15.137,-2.012],[15.156,-1.978],[15.27,-1.447],[15.27,-0.877],[15.141,-0.505],[15.141,-0.171],[15.156,-0.087],[15.137,-0.068],[14.947,0],[14.727,0],[14.553,-0.023],[14.518,-0.042],[14.492,-0.114],[14.473,-0.027],[14.446,0],[14.294,0],[14.15,-0.03],[14.12,-0.114],[14.101,-0.103],[14.093,-0.034],[14.067,0],[13.907,0],[13.778,-0.03],[13.759,-0.049],[13.748,-0.114],[13.721,-0.11],[13.695,0],[13.527,0],[13.421,-0.023],[13.395,-0.042],[13.368,-0.114],[13.334,-0.11],[13.334,-0.065],[13.307,0],[13.148,0],[13.026,-0.03],[12.996,-0.114],[12.954,-0.11],[12.939,-0.027],[12.912,0],[12.761,0],[12.685,-0.023],[12.635,-0.049],[12.624,-0.114],[12.567,-0.11],[12.559,-0.034],[12.54,0],[12.381,0],[12.282,-0.03],[12.256,-0.049],[12.244,-0.114],[12.18,-0.11],[12.172,-0.027],[12.145,0],[12.001,0],[11.902,-0.03],[11.876,-0.065],[11.865,-0.114],[11.792,-0.103],[11.785,-0.027],[11.758,0],[11.629,0],[11.523,-0.03],[11.504,-0.049],[11.492,-0.114],[11.413,-0.11],[11.386,0],[11.287,0],[11.166,-0.023],[11.124,-0.049],[11.113,-0.114],[11.029,-0.114],[11.018,-0.034],[10.984,0],[10.877,0],[10.786,-0.023],[10.752,-0.049],[10.741,-0.114],[10.642,-0.114],[10.631,-0.027],[10.604,0],[10.483,0],[10.407,-0.023],[10.372,-0.049],[10.361,-0.114],[10.255,-0.114],[10.232,-0.008],[10.095,0],[9.997,-0.038],[9.974,-0.121],[9.867,-0.114],[9.856,-0.019],[9.807,0],[9.678,-0.008],[9.647,-0.023],[9.613,-0.057],[9.613,-0.095],[9.643,-0.11],[9.594,-0.121],[9.48,-0.114],[9.457,-0.008],[9.29,-0.008],[9.233,-0.057],[9.233,-0.095],[9.245,-0.084],[9.271,-0.11],[9.214,-0.121],[9.101,-0.121],[9.082,-0.019],[9.04,0],[8.888,-0.023],[8.854,-0.065],[8.869,-0.065],[8.873,-0.099],[8.892,-0.087],[8.892,-0.11],[8.835,-0.121],[8.706,-0.121],[8.683,-0.008],[8.508,-0.015],[8.482,-0.042],[8.482,-0.072],[8.512,-0.11],[8.463,-0.121],[8.318,-0.121],[8.296,-0.008],[8.129,-0.015],[8.117,-0.027],[8.125,-0.11],[8.083,-0.121],[7.931,-0.121],[7.908,-0.008],[7.741,-0.015],[7.726,-0.121],[7.536,-0.121],[7.525,-0.019],[7.506,-0.008],[7.354,-0.015],[7.339,-0.121],[7.149,-0.121],[7.126,-0.008],[6.967,-0.008],[6.952,-0.121],[6.754,-0.121],[6.75,-0.027],[6.724,-0.008],[6.587,-0.008],[6.568,-0.034],[6.564,-0.121],[6.367,-0.121],[6.344,-0.008],[6.192,-0.008],[6.177,-0.121],[5.972,-0.121],[5.965,-0.015],[5.805,-0.008],[5.782,-0.121],[5.653,-0.129],[5.573,-0.11],[5.573,-0.019],[5.562,-0.008],[5.41,-0.008],[5.387,-0.121],[5.19,-0.121],[5.175,-0.008],[5.023,-0.008],[5.004,-0.027],[5.004,-0.118],[4.955,-0.129],[4.795,-0.121],[4.791,-0.019],[4.765,-0.008],[4.628,-0.008],[4.605,-0.121],[4.408,-0.121],[4.397,-0.11],[4.404,-0.027],[4.385,-0.008],[4.241,-0.008],[4.222,-0.027],[4.214,-0.118],[4.157,-0.129],[4.013,-0.121],[4.009,-0.027],[3.937,-0.008],[3.831,-0.015],[3.819,-0.118],[3.77,-0.129],[3.618,-0.121],[3.63,-0.103],[3.614,-0.095],[3.614,-0.019],[3.595,-0.008],[3.444,-0.015],[3.413,-0.129],[3.239,-0.121],[3.235,-0.057],[3.25,-0.042],[3.227,-0.042],[3.223,-0.106],[3.22,-0.027],[3.163,-0.008],[3.056,-0.008],[3.037,-0.027],[3.018,-0.129],[2.866,-0.121],[2.866,-0.106],[2.847,-0.103],[2.87,-0.095],[2.87,-0.049],[2.836,-0.038],[2.829,-0.076],[2.825,-0.027],[2.768,-0.008],[2.654,-0.015],[2.635,-0.057],[2.631,-0.129],[2.502,-0.129],[2.472,-0.046],[2.396,-0.015],[2.282,-0.008],[2.248,-0.027],[2.229,-0.129],[2.115,-0.129],[2.092,-0.046],[2.016,-0.015],[1.917,-0.008],[1.853,-0.027],[1.834,-0.129],[1.72,-0.129],[1.708,-0.057],[1.614,-0.015],[1.469,-0.015],[1.45,-0.034],[1.443,-0.125],[1.424,-0.137],[1.333,-0.129],[1.321,-0.057],[1.219,-0.015],[1.067,-0.015],[1.044,-0.129],[0.9,-0.129],[0.888,-0.087],[0.904,-0.072],[0.881,-0.049],[0.888,-0.042],[0.839,-0.023],[0.345,-0.015],[0.319,-0.08],[0.342,-0.345],[0.334,-0.452],[0.323,-0.471],[0.194,-0.471],[0.159,-0.543],[0.144,-0.634],[0.156,-0.661],[0.178,-0.668],[0.296,-0.672],[0.258,-0.885],[0.251,-1.469],[0.042,-1.473],[0.008,-1.507]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"x":"rear_x","y":"rail_top_above_bore"}}},"bounds":{"min":[-0.705,-1.19,-0.795],"max":[14.675,1.2,0.795]},"volume_in3":10.1324,"centroid":[6.0006,0.0536,-0.002],"shell":[6.6587,0.1694,-0.0015],"area_in2":174.904,"triangles":23390,"manifold":true,"slabs":[[-0.705,-0.84,-0.795,-0.311,1.2,0.795],[-0.311,-1.19,-0.795,0.478,1.2,0.795],[0.478,-1.113,-0.795,1.661,1.2,0.795],[1.661,-1.014,-0.795,2.056,1.2,0.795],[2.056,-0.86,-0.795,14.675,1.2,0.795]],"slots":["body","hardware","sockets"]},"geissele-premium-mil-spec-buffer-tube-assembly-castle-nut":{"part":"geissele-premium-mil-spec-buffer-tube-assembly-castle-nut","model":"geissele-premium-mil-spec-buffer-tube-assembly-castle-nut.glb","script":"geissele_premium_mil_spec_buffer_tube_assembly_castle_nut.py","inputs":{"geissele-premium-mil-spec-buffer-tube-assembly-castle-nut.notch_depth":0.1375,"geissele-premium-mil-spec-buffer-tube-assembly-castle-nut.notch_width":0.162,"geissele-premium-mil-spec-buffer-tube-assembly-castle-nut.notches":4,"geissele-premium-mil-spec-buffer-tube-assembly-castle-nut.od":1.363,"geissele-premium-mil-spec-buffer-tube-assembly-castle-nut.staking_notch_depth":0.082,"geissele-premium-mil-spec-buffer-tube-assembly-castle-nut.staking_notch_radial":0.075,"geissele-premium-mil-spec-buffer-tube-assembly-castle-nut.staking_notch_width":0.09,"geissele-premium-mil-spec-buffer-tube-assembly-castle-nut.staking_notches":3,"geissele-premium-mil-spec-buffer-tube-assembly-castle-nut.thickness":0.3765,"std.receiver_extension.thread_major_d":1.1813},"profiles":{},"bounds":{"min":[0,-0.6815,-0.6815],"max":[0.3765,0.6815,0.6815]},"volume_in3":0.1268,"centroid":[0.1825,0,0],"shell":[0.1825,0,0],"area_in2":3.6882,"triangles":3190,"manifold":true,"slabs":[[0,-0.682,-0.59,0.377,-0.341,0.59],[0,-0.341,-0.682,0.377,0.341,0.682],[0,0.341,-0.59,0.377,0.682,0.59]],"slots":["nut"]},"geissele-premium-mil-spec-buffer-tube-assembly-end-plate":{"part":"geissele-premium-mil-spec-buffer-tube-assembly-end-plate","model":"geissele-premium-mil-spec-buffer-tube-assembly-end-plate.glb","script":"geissele_premium_mil_spec_buffer_tube_assembly_end_plate.py","inputs":{"geissele-premium-mil-spec-buffer-tube-assembly-end-plate.boss_below_axis":0.9974,"geissele-premium-mil-spec-buffer-tube-assembly-end-plate.boss_height":0.375,"geissele-premium-mil-spec-buffer-tube-assembly-end-plate.boss_proud":0.0645,"geissele-premium-mil-spec-buffer-tube-assembly-end-plate.boss_width":0.496,"geissele-premium-mil-spec-buffer-tube-assembly-end-plate.corner_angle":31.33,"geissele-premium-mil-spec-buffer-tube-assembly-end-plate.dimple_depth":0.063,"geissele-premium-mil-spec-buffer-tube-assembly-end-plate.dimple_grow":0.005,"geissele-premium-mil-spec-buffer-tube-assembly-end-plate.edge_break":0.012,"geissele-premium-mil-spec-buffer-tube-assembly-end-plate.hole_d":1.1902,"geissele-premium-mil-spec-buffer-tube-assembly-end-plate.key_tip_below_axis":0.5619,"geissele-premium-mil-spec-buffer-tube-assembly-end-plate.key_width":0.125,"geissele-premium-mil-spec-buffer-tube-assembly-end-plate.lobe_centre_below_axis":0.9522,"geissele-premium-mil-spec-buffer-tube-assembly-end-plate.lobe_radius":0.4266,"geissele-premium-mil-spec-buffer-tube-assembly-end-plate.relief_bottom_below_axis":0.6575,"geissele-premium-mil-spec-buffer-tube-assembly-end-plate.relief_fillet_r":0.031,"geissele-premium-mil-spec-buffer-tube-assembly-end-plate.relief_floor_half_width":0.1119,"geissele-premium-mil-spec-buffer-tube-assembly-end-plate.relief_top_half_width":0.354,"geissele-premium-mil-spec-buffer-tube-assembly-end-plate.side_angle":13.5,"geissele-premium-mil-spec-buffer-tube-assembly-end-plate.thickness":0.124,"geissele-premium-mil-spec-buffer-tube-assembly-end-plate.top_above_axis":0.6817,"std.receiver_extension.key_slot_floor":0.55,"std.receiver_extension.key_slot_width":0.125,"std.receiver_extension.thread_major_d":1.1813},"profiles":{},"bounds":{"min":[-0.0645,-1.3788,-0.6816],"max":[0.124,0.6817,0.6816]},"volume_in3":0.1191,"centroid":[0.0515,-0.5977,0.0003],"shell":[0.0541,-0.4761,0.0004],"area_in2":3.2758,"triangles":3460,"manifold":true,"slabs":[[-0.064,-1.379,-0.419,0.124,-1.035,0.419],[-0.064,-1.035,-0.501,0.124,-0.692,0.501],[0,-0.692,-0.586,0.124,-0.349,0.586],[0,-0.349,-0.682,0.124,0.338,0.682],[0,0.338,-0.592,0.124,0.682,0.592]],"slots":["plate"]},"geissele-premium-mil-spec-buffer-tube":{"part":"geissele-premium-mil-spec-buffer-tube","model":"geissele-premium-mil-spec-buffer-tube.glb","script":"geissele_premium_mil_spec_buffer_tube.py","inputs":{"geissele-premium-mil-spec-buffer-tube.channel_depth":0.05,"geissele-premium-mil-spec-buffer-tube.channel_width":0.335,"geissele-premium-mil-spec-buffer-tube.key_slot_length":1,"geissele-premium-mil-spec-buffer-tube.land_bottom_below_axis":0.59,"geissele-premium-mil-spec-buffer-tube.land_front_from_front":1.507,"geissele-premium-mil-spec-buffer-tube.mark2_base_above_bottom":0.076,"geissele-premium-mil-spec-buffer-tube.mark2_height":0.067,"geissele-premium-mil-spec-buffer-tube.mark2_length":0.555,"geissele-premium-mil-spec-buffer-tube.mark2_rear_from_rear":0.263,"geissele-premium-mil-spec-buffer-tube.mark_base_above_bottom":0.193,"geissele-premium-mil-spec-buffer-tube.mark_height":0.093,"geissele-premium-mil-spec-buffer-tube.mark_length":0.689,"geissele-premium-mil-spec-buffer-tube.mark_proud":0.002,"geissele-premium-mil-spec-buffer-tube.mark_rear_from_rear":0.204,"geissele-premium-mil-spec-buffer-tube.mark_slant":12.7,"geissele-premium-mil-spec-buffer-tube.mouth_lip":0.11,"geissele-premium-mil-spec-buffer-tube.position_hole_d":0.331,"geissele-premium-mil-spec-buffer-tube.position_hole_rear_from_rear":0.495,"geissele-premium-mil-spec-buffer-tube.position_step":0.658,"geissele-premium-mil-spec-buffer-tube.rail_full_from_front":2.897,"geissele-premium-mil-spec-buffer-tube.ramp_top_from_front":2.416,"geissele-premium-mil-spec-buffer-tube.rear_edge_break":0.06,"geissele-premium-mil-spec-buffer-tube.thread_length":1.288,"geissele-premium-mil-spec-buffer-tube.tube_front_behind_pin":0.669,"geissele-premium-mil-spec-buffer-tube.tube_length":7.25,"geissele-premium-mil-spec-buffer-tube.tube_od":1.148,"std.receiver_extension.bore_d":1,"std.receiver_extension.carbine_rear_wall":0.072,"std.receiver_extension.carbine_vent_d":0.094,"std.receiver_extension.key_slot_floor":0.55,"std.receiver_extension.key_slot_width":0.125,"std.receiver_extension.rail_bottom_below_axis":0.874,"std.receiver_extension.rail_width":0.49,"std.receiver_extension.thread_major_d":1.1813,"std.receiver_extension.thread_minor_d":1.1093,"std.receiver_extension.thread_pitch":0.0625},"profiles":{},"bounds":{"min":[0.669,-0.874,-0.5907],"max":[7.919,0.5907,0.5907]},"volume_in3":2.389,"centroid":[4.6627,-0.159,-0.0001],"shell":[4.4049,-0.0776,-0.0007],"area_in2":58.2898,"triangles":32432,"manifold":true,"slabs":[[0.669,-0.591,-0.591,2.958,0.591,0.591],[2.958,-0.741,-0.574,3.34,0.574,0.574],[3.34,-0.874,-0.574,7.919,0.574,0.574]],"slots":["tube","mark"]},"geissele-ssa-e":{"part":"geissele-ssa-e","model":"geissele-ssa-e.glb","script":"geissele_ssa_e.py","inputs":{"geissele-ssa-e.block_width":0.305,"geissele-ssa-e.body_width":0.25,"geissele-ssa-e.boss_d":0.29,"geissele-ssa-e.disconnector_width":0.17,"geissele-ssa-e.hammer_boss_d":0.25,"geissele-ssa-e.hammer_hole_d":0.078,"geissele-ssa-e.hammer_hole_x":0.533,"geissele-ssa-e.hammer_hole_y":0.555,"geissele-ssa-e.hammer_width":0.22,"geissele-ssa-e.pin_diameter":0.154,"geissele-ssa-e.pin_length":0.83,"geissele-ssa-e.shoe_width":0.265,"std.ar15.fcg_pocket_width":0.69,"std.ar15.hammer_pin_x":2.771,"std.ar15.hammer_pin_y":-0.375,"std.ar15.trigger_boss_length":0.664,"std.ar15.trigger_pin_x":1.928,"std.ar15.trigger_pin_y":-0.689,"std.ar15.trigger_slot_front_ahead_of_pin":0.52,"std.ar15.trigger_slot_width":0.312},"profiles":{"side":[[-1.097,-0.216],[-1.097,-0.247],[-1.085,-0.273],[-1,-0.284],[-0.992,-0.278],[-0.954,-0.278],[-0.875,-0.285],[-0.037,-0.288],[-0.029,-0.298],[-0.027,-0.365],[0,-0.412],[0.001,-0.446],[-0.046,-0.555],[-0.078,-0.685],[-0.087,-0.805],[-0.087,-0.89],[-0.077,-0.962],[-0.044,-1.083],[0.012,-1.213],[0.083,-1.318],[0.138,-1.385],[0.162,-1.403],[0.177,-1.403],[0.195,-1.393],[0.212,-1.37],[0.217,-1.35],[0.161,-1.258],[0.119,-1.168],[0.095,-1.077],[0.086,-0.998],[0.085,-0.931],[0.094,-0.855],[0.108,-0.797],[0.137,-0.721],[0.197,-0.614],[0.275,-0.524],[0.344,-0.467],[0.363,-0.467],[0.378,-0.458],[0.381,-0.437],[0.403,-0.437],[0.463,-0.406],[0.492,-0.383],[0.498,-0.372],[0.506,-0.215],[0.524,-0.208],[0.748,-0.213],[0.761,-0.203],[0.772,-0.168],[0.779,0.005],[0.781,0.02],[0.788,0.025],[0.78,0.05],[0.517,0.049],[0.515,0.137],[0.443,0.137],[0.378,0.155],[0.322,0.158],[0.309,0.297],[0.3,0.34],[0.202,0.458],[0.159,0.485],[0.123,0.48],[0.099,0.459],[0.081,0.403],[0.081,0.349],[0.107,0.328],[0.136,0.326],[0.156,0.289],[0.156,0.247],[0.138,0.208],[0.123,0.184],[0.094,0.157],[0.094,0.147],[0.065,0.145],[-0.096,0.029],[-0.782,0.026],[-1.064,-0.007],[-1.079,-0.019],[-1.088,-0.043]],"hammer":[[-0.316,1.042],[-0.31,1.022],[-0.226,0.958],[-0.176,0.9],[-0.134,0.822],[-0.106,0.713],[-0.11,0.592],[-0.154,0.429],[-0.156,0.391],[-0.168,0.376],[-0.248,0.329],[-0.243,0.313],[-0.225,0.294],[-0.195,0.276],[-0.051,0.233],[0.045,0.219],[0.079,0.225],[0.096,0.247],[0.105,0.327],[0.078,0.351],[0.056,0.352],[0.052,0.424],[0.063,0.475],[0.086,0.517],[0.121,0.55],[0.163,0.565],[0.219,0.563],[0.22,0.528],[0.232,0.509],[0.273,0.491],[0.304,0.49],[0.312,0.481],[0.398,0.368],[0.54,0.158],[0.542,0.137],[0.584,0.105],[0.595,0.105],[0.651,0.067],[0.657,0.051],[0.78,0.041],[0.789,0.026],[0.804,0.02],[0.804,-0.009],[0.816,-0.023],[0.87,-0.019],[0.896,-0.01],[0.982,0.041],[1.03,0.084],[1.077,0.16],[1.095,0.213],[1.104,0.269],[1.094,0.35],[1.071,0.406],[1.027,0.469],[0.981,0.512],[0.937,0.539],[0.609,0.7],[0.27,0.859],[0.229,0.903],[0.218,0.964],[0.196,0.987],[-0.152,1.143],[-0.228,1.17],[-0.25,1.166],[-0.265,1.153]],"disconnector":[[-0.757,0.027],[-0.756,0.026],[-0.187,0.029],[-0.189,0.135],[-0.297,0.135],[-0.314,0.154],[-0.324,0.206],[-0.315,0.23],[-0.244,0.286],[-0.261,0.311],[-0.264,0.337],[-0.283,0.374],[-0.311,0.393],[-0.383,0.388],[-0.525,0.208],[-0.572,0.188],[-0.721,0.142],[-0.744,0.13],[-0.754,0.111]]},"features":{"side":{},"hammer":{},"disconnector":{}},"placement":{"side":{"plane":"xy","offset":{}},"hammer":{"plane":"xy","offset":{}},"disconnector":{"plane":"xy","offset":{}}},"bounds":{"min":[-1.097,-1.403,-0.415],"max":[1.104,1.17,0.415]},"volume_in3":0.4771,"centroid":[0.1419,0.0768,0],"shell":[0.165,0.0835,0],"area_in2":9.0473,"triangles":2590,"manifold":true,"slabs":[[-0.057,-1.403,-0.132,0.217,-1.035,0.132],[-0.087,-1.035,-0.132,0.167,-0.668,0.132],[-0.074,-0.668,-0.132,0.502,-0.3,0.132],[-1.097,-0.3,-0.415,1.011,0.067,0.415],[-0.756,0.067,-0.415,1.104,0.435,0.415],[-0.152,0.435,-0.332,1.051,0.802,0.332],[-0.316,0.802,-0.11,0.391,1.17,0.11]],"slots":["body"]},"geissele-super-42-h1":{"part":"geissele-super-42-h1","model":"geissele-super-42-h1.glb","script":"geissele_super_42.py","inputs":{"geissele-super-42-h1.body_d":0.687,"geissele-super-42-h1.coils":26,"geissele-super-42-h1.free_length":11.125,"geissele-super-42-h1.installed_length":6.972,"geissele-super-42-h1.length":3.251,"geissele-super-42-h1.od":0.98,"geissele-super-42-h1.shoulder_d":0.762,"geissele-super-42-h1.spring_od":0.95,"geissele-super-42-h1.strand_d":0.045,"geissele-super-42-h1.stranded_thickness":0.097,"geissele-super-42-h1.strands":3,"geissele-super-42-h1.twist_pitch":0.475,"std.carbine_buffer.body_d":0.687,"std.carbine_buffer.body_length":2.854,"std.carbine_buffer.body_start":0.5145,"std.carbine_buffer.bumper_band":0.06,"std.carbine_buffer.bumper_d":0.687,"std.carbine_buffer.bumper_exposed":0.4,"std.carbine_buffer.bumper_taper":13.5,"std.carbine_buffer.head_d":0.98,"std.carbine_buffer.head_flat_across":0.952,"std.carbine_buffer.head_rim":0.214,"std.carbine_buffer.head_thickness":0.254,"std.carbine_buffer.length":3.251,"std.carbine_buffer.pilot_d":0.781,"std.carbine_buffer.pilot_end":0.468,"std.carbine_buffer.pin_d":0.122,"std.carbine_buffer.pin_from_open_end":0.24,"std.receiver_extension.bore_d":1},"profiles":{},"bounds":{"min":[0,-0.49,-0.49],"max":[7.2216,0.4831,0.49]},"volume_in3":1.6357,"centroid":[1.9558,0,0],"shell":[3.2626,0.0001,0],"area_in2":43.3743,"triangles":33376,"manifold":true,"slabs":[[0,-0.49,-0.49,7.222,0.483,0.49]],"slots":["body","bumper","pin","spring"]},"geissele-super-42-h2":{"part":"geissele-super-42-h2","model":"geissele-super-42-h2.glb","script":"geissele_super_42.py","inputs":{"geissele-super-42-h1.body_d":0.687,"geissele-super-42-h1.coils":26,"geissele-super-42-h1.free_length":11.125,"geissele-super-42-h1.installed_length":6.972,"geissele-super-42-h1.shoulder_d":0.762,"geissele-super-42-h1.spring_od":0.95,"geissele-super-42-h1.strand_d":0.045,"geissele-super-42-h1.stranded_thickness":0.097,"geissele-super-42-h1.strands":3,"geissele-super-42-h1.twist_pitch":0.475,"geissele-super-42-h2.length":3.251,"geissele-super-42-h2.od":0.98,"std.carbine_buffer.body_d":0.687,"std.carbine_buffer.body_length":2.854,"std.carbine_buffer.body_start":0.5145,"std.carbine_buffer.bumper_band":0.06,"std.carbine_buffer.bumper_d":0.687,"std.carbine_buffer.bumper_exposed":0.4,"std.carbine_buffer.bumper_taper":13.5,"std.carbine_buffer.head_d":0.98,"std.carbine_buffer.head_flat_across":0.952,"std.carbine_buffer.head_rim":0.214,"std.carbine_buffer.head_thickness":0.254,"std.carbine_buffer.length":3.251,"std.carbine_buffer.pilot_d":0.781,"std.carbine_buffer.pilot_end":0.468,"std.carbine_buffer.pin_d":0.122,"std.carbine_buffer.pin_from_open_end":0.24,"std.receiver_extension.bore_d":1},"profiles":{},"bounds":{"min":[0,-0.49,-0.49],"max":[7.2216,0.4831,0.49]},"volume_in3":1.6357,"centroid":[1.9558,0,0],"shell":[3.2626,0.0001,0],"area_in2":43.3743,"triangles":33376,"manifold":true,"slabs":[[0,-0.49,-0.49,7.222,0.483,0.49]],"slots":["body","bumper","pin","spring"]},"geissele-super-42-h3":{"part":"geissele-super-42-h3","model":"geissele-super-42-h3.glb","script":"geissele_super_42.py","inputs":{"geissele-super-42-h1.body_d":0.687,"geissele-super-42-h1.coils":26,"geissele-super-42-h1.free_length":11.125,"geissele-super-42-h1.installed_length":6.972,"geissele-super-42-h1.shoulder_d":0.762,"geissele-super-42-h1.spring_od":0.95,"geissele-super-42-h1.strand_d":0.045,"geissele-super-42-h1.stranded_thickness":0.097,"geissele-super-42-h1.strands":3,"geissele-super-42-h1.twist_pitch":0.475,"geissele-super-42-h3.length":3.251,"geissele-super-42-h3.od":0.98,"std.carbine_buffer.body_d":0.687,"std.carbine_buffer.body_length":2.854,"std.carbine_buffer.body_start":0.5145,"std.carbine_buffer.bumper_band":0.06,"std.carbine_buffer.bumper_d":0.687,"std.carbine_buffer.bumper_exposed":0.4,"std.carbine_buffer.bumper_taper":13.5,"std.carbine_buffer.head_d":0.98,"std.carbine_buffer.head_flat_across":0.952,"std.carbine_buffer.head_rim":0.214,"std.carbine_buffer.head_thickness":0.254,"std.carbine_buffer.length":3.251,"std.carbine_buffer.pilot_d":0.781,"std.carbine_buffer.pilot_end":0.468,"std.carbine_buffer.pin_d":0.122,"std.carbine_buffer.pin_from_open_end":0.24,"std.receiver_extension.bore_d":1},"profiles":{},"bounds":{"min":[0,-0.49,-0.49],"max":[7.2216,0.4831,0.49]},"volume_in3":1.6357,"centroid":[1.9558,0,0],"shell":[3.2626,0.0001,0],"area_in2":43.3743,"triangles":33376,"manifold":true,"slabs":[[0,-0.49,-0.49,7.222,0.483,0.49]],"slots":["body","bumper","pin","spring"]},"geissele-super-duty-stripped-lower":{"part":"geissele-super-duty-stripped-lower","model":"geissele-super-duty-stripped-lower.glb","script":"geissele_super_duty_stripped_lower.py","inputs":{"geissele-super-duty-stripped-lower.bolt_catch_boss_bottom_y":-0.12,"geissele-super-duty-stripped-lower.bolt_catch_boss_front_x":3.555,"geissele-super-duty-stripped-lower.bolt_catch_boss_rear_x":3.008,"geissele-super-duty-stripped-lower.bolt_catch_gap_front_x":3.375,"geissele-super-duty-stripped-lower.bolt_catch_gap_rear_x":3.203,"geissele-super-duty-stripped-lower.buffer_axis_above_pin":0.8775,"geissele-super-duty-stripped-lower.fence_bottom_y":-0.975,"geissele-super-duty-stripped-lower.fence_corner_r":0.08,"geissele-super-duty-stripped-lower.fence_front_x":3.545,"geissele-super-duty-stripped-lower.fence_rear_x":2.955,"geissele-super-duty-stripped-lower.fence_top_y":-0.215,"geissele-super-duty-stripped-lower.grip_mating_y":-1.065,"geissele-super-duty-stripped-lower.grip_seat_y":-1.0695,"geissele-super-duty-stripped-lower.grip_shelf_top_x":-0.06,"geissele-super-duty-stripped-lower.hammer_pin_x":2.771,"geissele-super-duty-stripped-lower.hammer_pin_y":-0.375,"geissele-super-duty-stripped-lower.magwell_front_x":6.09,"geissele-super-duty-stripped-lower.magwell_wall_curve_bottom_y_left":-1.15,"geissele-super-duty-stripped-lower.magwell_wall_curve_top_y_left":-0.75,"geissele-super-duty-stripped-lower.magwell_wall_rear_x":3.5,"geissele-super-duty-stripped-lower.magwell_wall_rear_x_left":3.485,"geissele-super-duty-stripped-lower.magwell_wall_upper_rear_x_left":2.945,"geissele-super-duty-stripped-lower.rear_behind_pin":1.125,"geissele-super-duty-stripped-lower.rib_front_turn_y":-1.2,"geissele-super-duty-stripped-lower.rib_front_x":3.9,"geissele-super-duty-stripped-lower.rib_point_x":3.73,"geissele-super-duty-stripped-lower.rib_point_y":-1.5,"geissele-super-duty-stripped-lower.rib_proud":0.04,"geissele-super-duty-stripped-lower.rib_rear_turn_y":-1,"geissele-super-duty-stripped-lower.rib_rear_x":3.6,"geissele-super-duty-stripped-lower.roll_hole_d":0.045,"geissele-super-duty-stripped-lower.roll_hole_depth":0.06,"geissele-super-duty-stripped-lower.roll_hole_x":5.322,"geissele-super-duty-stripped-lower.roll_hole_y":0,"geissele-super-duty-stripped-lower.selector_pad_front_x":1.345,"geissele-super-duty-stripped-lower.selector_pad_height":0.225,"geissele-super-duty-stripped-lower.selector_pad_length":0.35,"geissele-super-duty-stripped-lower.selector_pad_proud":0.03,"geissele-super-duty-stripped-lower.selector_pad_rear_x":0.225,"geissele-super-duty-stripped-lower.selector_pad_y":-0.317,"geissele-super-duty-stripped-lower.selector_x":0.803,"geissele-super-duty-stripped-lower.selector_y":-0.466,"geissele-super-duty-stripped-lower.tower_front_x":-0.418,"geissele-super-duty-stripped-lower.trigger_guard_front_x":3.3425,"geissele-super-duty-stripped-lower.trigger_guard_front_y":-2.18,"geissele-super-duty-stripped-lower.trigger_guard_rear_x":1.4985,"geissele-super-duty-stripped-lower.trigger_guard_rear_y":-2.18,"geissele-super-duty-stripped-lower.trigger_opening_top_y":-1.09,"geissele-super-duty-stripped-lower.trigger_pin_x":1.928,"geissele-super-duty-stripped-lower.trigger_pin_y":-0.689,"geissele-super-duty-stripped-lower.well_roll_bottom_y":-0.21,"geissele-super-duty-stripped-lower.well_roll_crest_out":0.8,"geissele-super-duty-stripped-lower.well_roll_front_x":6.2395,"geissele-super-duty-stripped-lower.well_roll_rear_round":0.17,"geissele-super-duty-stripped-lower.well_roll_rear_x":2.955,"std.ar15.bolt_catch_boss_out":0.618,"std.ar15.bolt_catch_plunger_hole_d":0.156,"std.ar15.bolt_catch_plunger_hole_depth":0.4703,"std.ar15.bolt_catch_plunger_hole_y":-0.195,"std.ar15.bolt_catch_slot_bottom_y":-0.38,"std.ar15.bolt_catch_slot_floor":0.4409,"std.ar15.bolt_catch_slot_front_x":3.375,"std.ar15.bolt_catch_slot_width":0.172,"std.ar15.bore_axis_y":0.8775,"std.ar15.buffer_tower_front_x":-0.628,"std.ar15.buffer_tower_od":1.392,"std.ar15.deck_front_x":6.194,"std.ar15.deck_y":0.2485,"std.ar15.fcg_pin_hole_d":0.15675,"std.ar15.fcg_pocket_corner_r":0.218,"std.ar15.fcg_pocket_depth":1.249,"std.ar15.fcg_pocket_front_x":3.11,"std.ar15.fcg_pocket_length":2.87,"std.ar15.fcg_pocket_width":0.69,"std.ar15.front_lug_slot_width":0.5,"std.ar15.grip_lug_depth":0.93,"std.ar15.grip_lug_face_angle":60,"std.ar15.grip_lug_face_from_pin":1.228,"std.ar15.grip_lug_front_from_rear_face":2.3,"std.ar15.grip_lug_length":1.25,"std.ar15.grip_lug_width":0.375,"std.ar15.grip_seat_below_deck":1.318,"std.ar15.lower_body_width":0.88,"std.ar15.mag_catch_boss_edge_r":0.059,"std.ar15.mag_catch_boss_proud":0.0906,"std.ar15.mag_catch_boss_r":0.253,"std.ar15.mag_catch_boss_x":4.262,"std.ar15.mag_catch_cbore_d":0.312,"std.ar15.mag_catch_cbore_depth":0.25,"std.ar15.mag_catch_fence_out":0.549,"std.ar15.mag_catch_hole_d":0.2055,"std.ar15.mag_catch_slot_bottom_y":-0.689,"std.ar15.mag_catch_slot_floor":0.3799,"std.ar15.mag_catch_slot_front_x":4.557,"std.ar15.mag_catch_slot_h":0.252,"std.ar15.mag_catch_slot_rear_x":3.048,"std.ar15.mag_catch_x":3.291,"std.ar15.mag_catch_y":-0.565,"std.ar15.mag_release_pocket_depth":0.617,"std.ar15.mag_release_pocket_h":0.515,"std.ar15.mag_release_pocket_w":0.319,"std.ar15.magwell_band_bottom_y":-1.959,"std.ar15.magwell_band_front_x":4.549,"std.ar15.magwell_band_proud":0.059,"std.ar15.magwell_band_rear_x":3.975,"std.ar15.magwell_band_side":0.084,"std.ar15.magwell_box_length":2.398,"std.ar15.magwell_corner_r":0.062,"std.ar15.magwell_front_inner_x":6.025,"std.ar15.magwell_length":2.553,"std.ar15.magwell_outside_width":1.098,"std.ar15.magwell_spine_slot_width":0.47,"std.ar15.magwell_width":0.898,"std.ar15.pin_spacing":6.375,"std.ar15.pivot_hole_d":0.251,"std.ar15.rear_lug_slot_depth":0.63,"std.ar15.rear_lug_slot_rear_x":-0.402,"std.ar15.rear_lug_slot_width":0.5,"std.ar15.rear_underside_arc_center_below_seat":0.1928,"std.ar15.rear_underside_arc_center_x":-1.0238,"std.ar15.rear_underside_arc_r":0.75,"std.ar15.rear_underside_round_r":0.44,"std.ar15.rear_wall_arc_r":0.75,"std.ar15.receiver_rear_x":-1.125,"std.ar15.safety_detent_boss_below_deck":0.455,"std.ar15.safety_detent_boss_face":0.53,"std.ar15.safety_detent_boss_from_rear":0.36,"std.ar15.safety_detent_boss_length":0.43,"std.ar15.selector_hole_d":0.376,"std.ar15.selector_x":0.803,"std.ar15.takedown_hole_d":0.251,"std.ar15.takedown_spotface_d":0.44,"std.ar15.takedown_spotface_depth":0.04,"std.ar15.trigger_guard_ear_gap":0.442,"std.ar15.trigger_guard_ears_width":0.659,"std.ar15.trigger_guard_front_hole_d":0.1265,"std.ar15.trigger_guard_front_spotface_d":0.25,"std.ar15.trigger_guard_front_spotface_floor":0.3219,"std.ar15.trigger_guard_rear_hole_d":0.1285,"std.ar15.trigger_pin_x":1.928,"std.ar15.trigger_slot_front_ahead_of_pin":0.52,"std.ar15.trigger_slot_length":0.68,"std.ar15.trigger_slot_width":0.312,"std.ar15.upper_rear_face_x":-0.621,"std.receiver_extension.milspec_od":1.148},"profiles":{"side":[[-1.17,0.758],[-1.13,-0.232],[-1.08,-0.493],[-0.798,-0.53],[-0.528,-0.65],[-0.36,-0.822],[-0.248,-1.055],[-0.06,-1.078],[-0.06,-1.362],[-0.038,-1.39],[0.972,-1.975],[1.163,-1.99],[1.188,-2.345],[1.632,-2.35],[1.745,-2.273],[1.712,-2.17],[1.48,-2.028],[1.375,-1.752],[1.375,-1.592],[1.42,-1.433],[1.475,-1.333],[1.637,-1.185],[1.877,-1.09],[2.857,-1.085],[3.013,-1.115],[3.152,-1.19],[3.265,-1.292],[3.37,-1.453],[3.425,-1.723],[3.4,-1.877],[3.17,-2.142],[3.19,-2.302],[3.282,-2.35],[6.178,-1.82],[6.195,-1.723],[6.09,-1.562],[6.095,-0.567],[6.14,-0.442],[6.245,-0.303],[6.5,-0.147],[6.545,-0.067],[6.555,0.038],[6.51,0.137],[6.418,0.205],[6.008,0.24],[-0.038,0.265],[-0.268,0.35],[-0.495,0.613],[-0.6,0.903],[-0.585,1.188],[-0.635,1.568],[-0.968,1.575],[-1.095,1.522],[-1.125,1.413],[-1.165,1.127]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{}}},"bounds":{"min":[-1.125,-2.35,-0.6986],"max":[6.555,1.5735,0.8]},"volume_in3":5.1372,"centroid":[2.4143,-0.6058,0.0327],"shell":[2.8651,-0.6446,0.01],"area_in2":76.1288,"triangles":26142,"manifold":true,"interior":{"pocket":{"x":[0.24,3.11],"z":0.345,"floor_y":-1.0005},"rear_lug_slot":{"x":[-0.402,0.458],"z":0.25,"floor_y":-0.3815},"safety_detent_boss":{"x":[0.6,1.03],"face_z":0.185,"top_y":-0.2065},"trigger_slot":{"x":[1.768,2.448],"z":0.156},"magazine_well":{"x":[3.472,6.025],"z":0.449}},"holes":{"takedown":{"x":0,"y":0,"d":0.251},"pivot":{"x":6.375,"y":0,"d":0.251},"selector":{"x":0.803,"y":-0.466,"d":0.376},"hammer":{"x":2.771,"y":-0.375,"d":0.1568},"trigger":{"x":1.928,"y":-0.689,"d":0.1568},"guard rear":{"x":1.4985,"y":-2.18,"d":0.1285},"guard front":{"x":3.3425,"y":-2.18,"d":0.1265}},"catches":{"button_pocket":{"x":3.291,"y":-0.565,"floor_z":-0.068,"face_z":0.549},"catch_slot":{"x":[3.048,4.557],"floor_z":-0.3799},"bolt_catch_slot":{"x":[3.203,3.375],"bottom_y":-0.38,"floor_z":-0.4409}},"grip_mount":{"lug":{"seat_y":-1.0695,"x":[-0.075,1.175],"width":0.375,"foot_x":1.0072,"flat_y":-1.9995},"ears":{"width":0.659,"gap":0.442,"gap_top_y":-1.9995,"rear_x":[1.175,1.877],"front_x":[2.857,3.485]},"rear_underside":{"round_r":0.44,"arc_r":0.75,"axis_x":-1.0238,"axis_y":-1.2623}},"rear_walls":{"r":0.75,"centre":[0.122,0.9985],"x":[-0.621,0.122],"meets_face_y":0.8963,"runs_out":[0.055,0.2515],"toe_x":[-0.1255,0.055]},"deck":{"y":0.2485,"x":[-0.02,6.194]},"slabs":[[-1.125,-0.567,-0.696,-0.741,1.573,0.696],[-0.741,-0.917,-0.696,-0.357,1.573,0.696],[-0.357,-1.434,-0.44,0.027,0.422,0.44],[0.027,-1.655,-0.47,0.411,0.255,0.44],[0.411,-1.877,-0.44,0.795,0.249,0.44],[0.795,-2.35,-0.47,1.947,0.249,0.44],[1.947,-1.069,-0.44,2.715,0.249,0.44],[2.715,-1.161,-0.618,3.099,0.249,0.796],[3.099,-2.35,-0.618,3.867,0.249,0.8],[3.867,-2.243,-0.699,4.251,0.249,0.8],[4.251,-2.173,-0.699,4.635,0.249,0.8],[4.635,-2.102,-0.549,5.019,0.249,0.8],[5.019,-2.032,-0.549,5.403,0.249,0.8],[5.403,-1.962,-0.549,5.787,0.249,0.8],[5.787,-1.892,-0.549,6.171,0.249,0.8],[6.171,-1.821,-0.549,6.555,0.249,0.8]],"slots":["receiver"]},"geissele-super-duty-stripped-upper.receiver":{"part":"geissele-super-duty-stripped-upper","component":"receiver","model":"geissele-super-duty-stripped-upper.receiver.glb","script":"geissele_super_duty_stripped_upper.py","inputs":{"geissele-super-duty-stripped-upper.barrel_thread_major_d":1.2442,"geissele-super-duty-stripped-upper.barrel_thread_minor_d":1.1803,"geissele-super-duty-stripped-upper.barrel_thread_tpi":18,"geissele-super-duty-stripped-upper.body_radius":0.59,"geissele-super-duty-stripped-upper.bore_axis_above_pin":0.8775,"geissele-super-duty-stripped-upper.bore_d":1,"geissele-super-duty-stripped-upper.cam_pad_bottom_y":1.05,"geissele-super-duty-stripped-upper.cam_pad_edge_round":0.094,"geissele-super-duty-stripped-upper.cam_pad_face_z":0.5625,"geissele-super-duty-stripped-upper.cam_pad_front_x":5.58,"geissele-super-duty-stripped-upper.cam_pad_rear_x":4.6,"geissele-super-duty-stripped-upper.cam_pad_top_y":1.63,"geissele-super-duty-stripped-upper.charging_handle_above_bore":0.8563,"geissele-super-duty-stripped-upper.deflector_crest_x":2.35,"geissele-super-duty-stripped-upper.deflector_front_out":0.82,"geissele-super-duty-stripped-upper.deflector_out":1.25,"geissele-super-duty-stripped-upper.deflector_top_face_y":1.67,"geissele-super-duty-stripped-upper.deflector_top_wall_y":1.7,"geissele-super-duty-stripped-upper.dovetail_foot_half_width":0.323,"geissele-super-duty-stripped-upper.dovetail_foot_y":1.885,"geissele-super-duty-stripped-upper.fa_axis_angle":20,"geissele-super-duty-stripped-upper.fa_axis_x":-0.395,"geissele-super-duty-stripped-upper.fa_axis_z":1.09,"geissele-super-duty-stripped-upper.fa_bore_d":0.509,"geissele-super-duty-stripped-upper.fa_bore_depth":0.65,"geissele-super-duty-stripped-upper.fa_housing_r":0.3125,"geissele-super-duty-stripped-upper.fa_inner_bore_d":0.315,"geissele-super-duty-stripped-upper.fa_rear_x":-0.48,"geissele-super-duty-stripped-upper.front_face_x":7.036,"geissele-super-duty-stripped-upper.gas_tube_hole_d":0.1835,"geissele-super-duty-stripped-upper.gas_tube_relief_d":0.094,"geissele-super-duty-stripped-upper.gas_tube_relief_offset":0.078,"geissele-super-duty-stripped-upper.handle_seat_x":0.075,"geissele-super-duty-stripped-upper.hinge_axis_y":0.641,"geissele-super-duty-stripped-upper.hinge_axis_z":0.689,"geissele-super-duty-stripped-upper.hinge_boss_r":0.1365,"geissele-super-duty-stripped-upper.hinge_pin_d":0.1295,"geissele-super-duty-stripped-upper.latch_slot_bottom_y":1.52,"geissele-super-duty-stripped-upper.latch_slot_length":0.195,"geissele-super-duty-stripped-upper.latch_slot_top_y":1.935,"geissele-super-duty-stripped-upper.latch_slot_wall":0.156,"geissele-super-duty-stripped-upper.lug_hole_d":0.251,"geissele-super-duty-stripped-upper.lug_rear_face_top_y":0.458,"geissele-super-duty-stripped-upper.lug_wall_half_width":0.453,"geissele-super-duty-stripped-upper.lug_width":0.4945,"geissele-super-duty-stripped-upper.notch_bottom_y":1.58,"geissele-super-duty-stripped-upper.notch_top_y":1.91,"geissele-super-duty-stripped-upper.pivot_lug_front_x":6.591,"geissele-super-duty-stripped-upper.pivot_lug_r":0.246,"geissele-super-duty-stripped-upper.pivot_lug_rear_x":6.159,"geissele-super-duty-stripped-upper.port_bottom_y":0.841,"geissele-super-duty-stripped-upper.port_end_r":0.25,"geissele-super-duty-stripped-upper.port_front_x":6.036,"geissele-super-duty-stripped-upper.port_length":3.125,"geissele-super-duty-stripped-upper.rail_front_x":6.591,"geissele-super-duty-stripped-upper.rail_neck_bottom_y":1.7,"geissele-super-duty-stripped-upper.rail_neck_half_width":0.309,"geissele-super-duty-stripped-upper.rail_tongue_rear_x":-0.6,"geissele-super-duty-stripped-upper.rail_top_above_pin":2.09,"geissele-super-duty-stripped-upper.rear_flange_front_x":-0.47,"geissele-super-duty-stripped-upper.rear_flange_r":0.6938,"geissele-super-duty-stripped-upper.receiver_rear_x":-0.621,"geissele-super-duty-stripped-upper.right_photo_lens_distance":28,"geissele-super-duty-stripped-upper.right_photo_lens_x":4.6,"geissele-super-duty-stripped-upper.right_photo_lens_y":3,"geissele-super-duty-stripped-upper.side_bottom_y":1.44,"geissele-super-duty-stripped-upper.side_half_width":0.319,"geissele-super-duty-stripped-upper.takedown_lug_bottom_y":-0.212,"geissele-super-duty-stripped-upper.takedown_lug_front_x":0.226,"geissele-super-duty-stripped-upper.takedown_lug_rear_x":-0.236,"geissele-super-duty-stripped-upper.underside_y":0.2485,"std.ar15.bore_axis_y":0.8775,"std.ar15.buffer_tower_front_x":-0.628,"std.ar15.buffer_tower_od":1.392,"std.ar15.buffer_trough_r":0.5625,"std.ar15.charging_handle_channel_floor_y":1.5845,"std.ar15.charging_handle_channel_front_round_x":5.726,"std.ar15.charging_handle_channel_rear_half_width":0.209,"std.ar15.charging_handle_channel_rear_round_x":0.676,"std.ar15.charging_handle_channel_roof_y":1.9085,"std.ar15.charging_handle_channel_round_r":0.2665,"std.ar15.charging_handle_channel_slot_half_width":0.205,"std.ar15.charging_handle_channel_tier_half_width":0.25,"std.ar15.charging_handle_channel_tier_top_y":1.7115,"std.ar15.charging_handle_channel_top_half_width":0.22,"std.ar15.charging_handle_latch_slot_floor":0.045,"std.ar15.charging_handle_notch_chamfer":0.083,"std.ar15.charging_handle_notch_floor_y":1.571,"std.ar15.charging_handle_notch_roof_y":1.89,"std.ar15.deck_y":0.2485,"std.ar15.gas_tube_above_bore":0.78,"std.ar15.pin_spacing":6.375,"std.ar15.rail_tongue_end_r":0.4175,"std.ar15.rail_tongue_fillet_r":0.1476,"std.ar15.rail_tongue_front_x":0.277,"std.ar15.rail_tongue_half_width":0.318,"std.ar15.rail_tongue_shoulder_x":0.4165,"std.ar15.rear_lug_slot_rear_x":-0.402,"std.ar15.rear_lug_slot_width":0.5,"std.ar15.rear_wall_arc_r":0.75,"std.ar15.upper_barrel_thread_length":0.445,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.top_width":0.835},"profiles":{"side":[[-0.621,2.098],[-0.621,1.913],[-0.598,1.899],[-0.082,1.895],[0.004,1.799],[0.004,1.65],[-0.053,1.593],[-0.621,1.594],[-0.621,0.249],[6.609,0.248],[6.619,0.292],[6.675,0.292],[6.713,0.257],[6.742,0.289],[6.763,0.251],[6.792,0.289],[6.819,0.251],[6.848,0.289],[6.874,0.251],[6.904,0.289],[6.93,0.254],[6.965,0.289],[6.986,0.254],[7.036,0.307],[7.036,1.446],[7.006,1.479],[6.985,1.465],[6.965,1.497],[6.932,1.468],[6.909,1.497],[6.883,1.468],[6.853,1.497],[6.833,1.456],[6.798,1.497],[6.777,1.456],[6.742,1.498],[6.715,1.462],[6.704,1.474],[6.68,1.46],[6.614,1.464],[6.618,2.083],[6.564,2.105],[6.139,2.103],[6.124,1.986],[5.96,1.977],[5.947,2.084],[5.91,2.103],[5.746,2.101],[5.738,1.997],[5.672,1.984],[5.552,1.987],[5.545,2.085],[5.526,2.101],[5.353,2.101],[5.357,2.027],[5.341,1.99],[5.153,1.984],[5.168,1.97],[5.149,1.977],[5.146,2.08],[5.127,2.102],[4.963,2.102],[4.955,1.992],[4.875,1.982],[4.746,1.991],[4.744,2.084],[4.725,2.106],[4.57,2.1],[4.557,2.087],[4.546,1.974],[4.546,1.986],[4.344,1.989],[4.347,2.1],[4.177,2.101],[4.155,2.085],[4.155,2.003],[4.133,1.966],[4.067,1.97],[4.138,1.972],[4.138,1.986],[3.974,1.984],[3.958,1.997],[3.964,2.02],[3.949,2.015],[3.954,2.101],[3.784,2.101],[3.753,2.082],[3.745,1.984],[3.66,1.981],[3.571,1.995],[3.561,2.102],[3.388,2.099],[3.351,2.083],[3.341,1.976],[3.194,1.979],[3.178,1.996],[3.171,2.1],[2.992,2.1],[2.949,2.081],[2.946,1.996],[2.924,1.965],[2.795,1.968],[2.778,2.1],[2.555,2.089],[2.534,1.972],[2.518,1.982],[2.528,1.987],[2.405,1.984],[2.379,2.101],[2.215,2.101],[2.146,2.083],[2.137,1.98],[2.1,1.967],[2.02,1.971],[2.064,1.983],[2.005,1.995],[1.989,2.102],[1.748,2.088],[1.735,1.987],[1.693,1.979],[1.621,1.984],[1.603,2.092],[1.59,2.103],[1.534,2.091],[1.42,2.1],[1.342,2.084],[1.326,1.971],[1.226,1.968],[1.203,2.1],[-0.202,2.109]]},"features":{"side":{"forward_assist_rim":[[[-0.778,1.12],[-0.594,1.12],[-0.595,0.486],[-0.78,0.487]]],"forward_assist_bore":[[[-0.735,1.067],[-0.647,1.067],[-0.648,0.539],[-0.736,0.539]]],"deflector":[[[2.032,1.596],[2.12,1.69],[2.765,1.688],[2.868,1.624],[2.926,1.448],[2.931,0.89],[2.72,0.826],[2.031,0.828],[2.01,0.921]]],"deflector_crest":[[[2.208,1.522],[2.296,1.522],[2.295,1.068],[2.207,1.068]]],"port":[[[2.911,1.345],[6.07,1.339],[6.069,0.802],[2.91,0.808]]],"hinge_rear":[[[2.743,0.847],[2.902,0.846],[2.901,0.368],[2.742,0.369]]],"hinge_front":[[[6.107,0.738],[6.289,0.737],[6.288,0.391],[6.106,0.392]]]}},"placement":{"side":{"plane":"xy","offset":{}}},"bounds":{"min":[-0.621,-0.246,-0.6938],"max":[7.036,2.09,1.4145]},"volume_in3":4.6946,"centroid":[3.0021,0.9998,0.0829],"shell":[3.0031,1.0724,0.0537],"area_in2":82.774,"triangles":16332,"manifold":true,"rear_corner":{"r":0.75,"centre":[0.122,0.9985],"x":[-0.628,-0.0116],"reach_z":0.696,"trough_r":0.5625},"slabs":[[-0.621,0.249,-0.694,-0.238,2.09,1.415],[-0.238,-0.212,-0.59,0.145,2.09,1.365],[0.145,-0.212,-0.59,0.528,2.09,1.226],[0.528,0.249,-0.59,0.91,1.972,1.087],[0.91,0.249,-0.59,1.293,1.972,0.947],[1.293,0.249,-0.59,1.676,1.972,0.808],[1.676,0.249,-0.59,2.059,1.972,0.669],[2.059,0.249,-0.59,2.442,1.972,1.25],[2.442,0.249,-0.59,2.825,1.972,1.187],[2.825,0.249,-0.59,3.207,1.972,0.925],[3.207,0.249,-0.59,5.887,1.972,0.589],[5.887,-0.223,-0.59,6.27,1.972,0.826],[6.27,-0.246,-0.613,6.653,1.972,0.62],[6.653,0.255,-0.622,7.036,1.5,0.622]],"slots":["receiver"]},"geissele-super-precision-micro-193":{"part":"geissele-super-precision-micro-193","model":"geissele-super-precision-micro-193.glb","script":"geissele_super_precision_micro.py","inputs":{"geissele-super-precision-micro-193.base_end_top_above_rail":0.028,"geissele-super-precision-micro-193.base_left_z":0.328,"geissele-super-precision-micro-193.base_right_face_bottom":0.091,"geissele-super-precision-micro-193.base_right_face_top":0.088,"geissele-super-precision-micro-193.base_right_foot_z":0.494,"geissele-super-precision-micro-193.base_right_upper_z":0.611,"geissele-super-precision-micro-193.base_right_z":0.676,"geissele-super-precision-micro-193.base_top_above_rail":0.34,"geissele-super-precision-micro-193.bolt_axis_above_rail":-0.017,"geissele-super-precision-micro-193.button_d":0.35,"geissele-super-precision-micro-193.button_proud":0.01,"geissele-super-precision-micro-193.clamp_below_rail":0.274,"geissele-super-precision-micro-193.collar_d":0.455,"geissele-super-precision-micro-193.collar_length":0.174,"geissele-super-precision-micro-193.deck_above_rail":1.341,"geissele-super-precision-micro-193.deck_x":0.002,"geissele-super-precision-micro-193.edge_break":0.008,"geissele-super-precision-micro-193.jaw_bottom_below_rail":0.183,"geissele-super-precision-micro-193.jaw_chamfer":0.09,"geissele-super-precision-micro-193.jaw_length":0.731,"geissele-super-precision-micro-193.jaw_outer_z":0.649,"geissele-super-precision-micro-193.lug_depth":0.084,"geissele-super-precision-micro-193.lug_length":0.2,"geissele-super-precision-micro-193.lug_spacing":0.394,"geissele-super-precision-micro-193.lug_width":0.369,"geissele-super-precision-micro-193.mount_length":1.37,"geissele-super-precision-micro-193.neck_bottom_above_rail":0.37,"geissele-super-precision-micro-193.neck_bottom_width":0.66,"geissele-super-precision-micro-193.neck_straight_bottom_above_rail":0.58,"geissele-super-precision-micro-193.neck_straight_top_above_rail":1.02,"geissele-super-precision-micro-193.neck_top_width":0.5,"geissele-super-precision-micro-193.neck_waist_above_rail":0.666,"geissele-super-precision-micro-193.neck_waist_length":1.02,"geissele-super-precision-micro-193.neck_waist_width":0.459,"geissele-super-precision-micro-193.nut_across":0.551,"geissele-super-precision-micro-193.nut_length":0.241,"geissele-super-precision-micro-193.nut_slot_depth":0.04,"geissele-super-precision-micro-193.nut_slot_width":0.05,"geissele-super-precision-micro-193.plate_bottom_above_rail":1.068,"geissele-super-precision-micro-193.plate_chamfer_height":0.07,"geissele-super-precision-micro-193.plate_chamfer_width":0.06,"geissele-super-precision-micro-193.plate_left_z":0.434,"geissele-super-precision-micro-193.plate_length":1.872,"geissele-super-precision-micro-193.plate_right_z":0.616,"geissele-super-precision-micro-193.pocket_d":0.193,"geissele-super-precision-micro-193.pocket_depth":0.15,"geissele-super-precision-micro-193.pocket_x":0.33,"geissele-super-precision-micro-193.screw_counterbore_d":0.246,"geissele-super-precision-micro-193.screw_counterbore_depth":0.1,"geissele-super-precision-micro-193.screw_hole_d":0.128,"geissele-super-precision-micro-193.screw_x":0.697,"geissele-super-precision-micro-193.screw_z":0.191,"geissele-super-precision-micro-193.shoulder_top_above_rail":0.369,"geissele-super-precision-micro-193.shoulder_x":0.512,"geissele-super-precision-micro-193.width_over_nut":1.74,"std.density.aluminium_7075":1.632,"std.density.steel":4.565,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{},"features":{},"placement":{},"bounds":{"min":[-0.934,-0.2925,-1.064],"max":[0.938,1.341,0.686]},"volume_in3":1.5711,"centroid":[0.0006,0.5732,0.0141],"shell":[0.0008,0.554,-0.0141],"area_in2":15.2583,"triangles":7874,"manifold":true,"rail_seat":{"x":[-0.685,0.685],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-0.934,-0.274,-0.452,-0.56,1.341,0.676],[-0.56,-0.292,-1.064,0.564,1.341,0.686],[0.564,-0.274,-0.452,0.938,1.341,0.676]],"slots":["body","hardware","button"]},"geissele-super-precision-micro-absolute":{"part":"geissele-super-precision-micro-absolute","model":"geissele-super-precision-micro-absolute.glb","script":"geissele_super_precision_micro.py","inputs":{"geissele-super-precision-micro-absolute.base_end_top_above_rail":0.085,"geissele-super-precision-micro-absolute.base_left_z":0.39,"geissele-super-precision-micro-absolute.base_right_face_bottom":0.141,"geissele-super-precision-micro-absolute.base_right_face_top":0.183,"geissele-super-precision-micro-absolute.base_right_foot_z":0.563,"geissele-super-precision-micro-absolute.base_right_upper_z":0.535,"geissele-super-precision-micro-absolute.base_right_z":0.676,"geissele-super-precision-micro-absolute.base_top_above_rail":0.282,"geissele-super-precision-micro-absolute.bolt_axis_above_rail":0.014,"geissele-super-precision-micro-absolute.button_d":0.349,"geissele-super-precision-micro-absolute.button_proud":0.01,"geissele-super-precision-micro-absolute.clamp_below_rail":0.264,"geissele-super-precision-micro-absolute.collar_d":0.479,"geissele-super-precision-micro-absolute.collar_length":0.155,"geissele-super-precision-micro-absolute.deck_above_rail":0.821,"geissele-super-precision-micro-absolute.deck_x":0,"geissele-super-precision-micro-absolute.edge_break":0.008,"geissele-super-precision-micro-absolute.jaw_bottom_below_rail":0.241,"geissele-super-precision-micro-absolute.jaw_chamfer":0.09,"geissele-super-precision-micro-absolute.jaw_length":0.69,"geissele-super-precision-micro-absolute.jaw_outer_z":0.69,"geissele-super-precision-micro-absolute.lug_depth":0.085,"geissele-super-precision-micro-absolute.lug_length":0.18,"geissele-super-precision-micro-absolute.lug_spacing":0.394,"geissele-super-precision-micro-absolute.lug_width":0.394,"geissele-super-precision-micro-absolute.mount_length":1.37,"geissele-super-precision-micro-absolute.neck_bottom_above_rail":0.327,"geissele-super-precision-micro-absolute.neck_bottom_width":0.62,"geissele-super-precision-micro-absolute.neck_top_width":0.507,"geissele-super-precision-micro-absolute.neck_waist_above_rail":0.46,"geissele-super-precision-micro-absolute.neck_waist_length":0.997,"geissele-super-precision-micro-absolute.neck_waist_width":0.42,"geissele-super-precision-micro-absolute.nut_across":0.535,"geissele-super-precision-micro-absolute.nut_length":0.259,"geissele-super-precision-micro-absolute.nut_slot_depth":0.04,"geissele-super-precision-micro-absolute.nut_slot_width":0.05,"geissele-super-precision-micro-absolute.plate_bottom_above_rail":0.556,"geissele-super-precision-micro-absolute.plate_chamfer_height":0.12,"geissele-super-precision-micro-absolute.plate_chamfer_width":0.085,"geissele-super-precision-micro-absolute.plate_left_z":0.479,"geissele-super-precision-micro-absolute.plate_length":1.881,"geissele-super-precision-micro-absolute.plate_right_z":0.611,"geissele-super-precision-micro-absolute.pocket_d":0.193,"geissele-super-precision-micro-absolute.pocket_depth":0.15,"geissele-super-precision-micro-absolute.pocket_x":0.33,"geissele-super-precision-micro-absolute.screw_counterbore_d":0.2,"geissele-super-precision-micro-absolute.screw_counterbore_depth":0.1,"geissele-super-precision-micro-absolute.screw_hole_d":0.128,"geissele-super-precision-micro-absolute.screw_x":0.697,"geissele-super-precision-micro-absolute.screw_z":0.191,"geissele-super-precision-micro-absolute.shoulder_top_above_rail":0.313,"geissele-super-precision-micro-absolute.shoulder_x":0.531,"geissele-super-precision-micro-absolute.width_over_nut":1.78,"std.density.aluminium_7075":1.632,"std.density.steel":4.565,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{},"features":{},"placement":{},"bounds":{"min":[-0.9405,-0.264,-1.104],"max":[0.9405,0.821,0.686]},"volume_in3":1.3102,"centroid":[0,0.329,-0.0064],"shell":[0,0.3115,-0.0305],"area_in2":13.8739,"triangles":8170,"manifold":true,"rail_seat":{"x":[-0.685,0.685],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-0.941,-0.264,-0.479,-0.564,0.821,0.676],[-0.564,-0.264,-1.104,0.564,0.821,0.686],[0.564,-0.264,-0.479,0.941,0.821,0.676]],"slots":["body","hardware","button"]},"geissele-super-precision-micro-lower-13":{"part":"geissele-super-precision-micro-lower-13","model":"geissele-super-precision-micro-lower-13.glb","script":"geissele_super_precision_micro.py","inputs":{"geissele-super-precision-micro-lower-13.base_end_top_above_rail":-0.013,"geissele-super-precision-micro-lower-13.base_left_z":0.345,"geissele-super-precision-micro-lower-13.base_right_face_bottom":0.091,"geissele-super-precision-micro-lower-13.base_right_face_top":0.088,"geissele-super-precision-micro-lower-13.base_right_foot_z":0.494,"geissele-super-precision-micro-lower-13.base_right_upper_z":0.611,"geissele-super-precision-micro-lower-13.base_right_z":0.653,"geissele-super-precision-micro-lower-13.base_top_above_rail":0.311,"geissele-super-precision-micro-lower-13.bolt_axis_above_rail":-0.011,"geissele-super-precision-micro-lower-13.button_d":0.272,"geissele-super-precision-micro-lower-13.button_proud":0.01,"geissele-super-precision-micro-lower-13.clamp_below_rail":0.256,"geissele-super-precision-micro-lower-13.collar_d":0.43,"geissele-super-precision-micro-lower-13.collar_length":0.155,"geissele-super-precision-micro-lower-13.deck_above_rail":0.884,"geissele-super-precision-micro-lower-13.deck_x":-0.009,"geissele-super-precision-micro-lower-13.edge_break":0.008,"geissele-super-precision-micro-lower-13.jaw_bottom_below_rail":0.183,"geissele-super-precision-micro-lower-13.jaw_chamfer":0.09,"geissele-super-precision-micro-lower-13.jaw_length":0.738,"geissele-super-precision-micro-lower-13.jaw_outer_z":0.636,"geissele-super-precision-micro-lower-13.lug_depth":0.084,"geissele-super-precision-micro-lower-13.lug_length":0.188,"geissele-super-precision-micro-lower-13.lug_spacing":0.394,"geissele-super-precision-micro-lower-13.lug_width":0.367,"geissele-super-precision-micro-lower-13.mount_length":1.37,"geissele-super-precision-micro-lower-13.neck_bottom_above_rail":0.319,"geissele-super-precision-micro-lower-13.neck_bottom_width":0.665,"geissele-super-precision-micro-lower-13.neck_top_width":0.668,"geissele-super-precision-micro-lower-13.neck_waist_above_rail":0.49,"geissele-super-precision-micro-lower-13.neck_waist_length":1.006,"geissele-super-precision-micro-lower-13.neck_waist_width":0.422,"geissele-super-precision-micro-lower-13.nut_across":0.529,"geissele-super-precision-micro-lower-13.nut_length":0.236,"geissele-super-precision-micro-lower-13.nut_slot_depth":0.04,"geissele-super-precision-micro-lower-13.nut_slot_width":0.05,"geissele-super-precision-micro-lower-13.plate_bottom_above_rail":0.678,"geissele-super-precision-micro-lower-13.plate_chamfer_height":0.11,"geissele-super-precision-micro-lower-13.plate_chamfer_width":0.1,"geissele-super-precision-micro-lower-13.plate_left_z":0.475,"geissele-super-precision-micro-lower-13.plate_length":1.879,"geissele-super-precision-micro-lower-13.plate_right_z":0.595,"geissele-super-precision-micro-lower-13.pocket_d":0.198,"geissele-super-precision-micro-lower-13.pocket_depth":0.15,"geissele-super-precision-micro-lower-13.pocket_x":0.325,"geissele-super-precision-micro-lower-13.screw_counterbore_d":0.23,"geissele-super-precision-micro-lower-13.screw_counterbore_depth":0.1,"geissele-super-precision-micro-lower-13.screw_hole_d":0.132,"geissele-super-precision-micro-lower-13.screw_x":0.689,"geissele-super-precision-micro-lower-13.screw_z":0.198,"geissele-super-precision-micro-lower-13.shoulder_top_above_rail":0.315,"geissele-super-precision-micro-lower-13.shoulder_x":0.526,"geissele-super-precision-micro-lower-13.width_over_nut":1.68,"std.density.aluminium_7075":1.632,"std.density.steel":4.565,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{},"features":{},"placement":{},"bounds":{"min":[-0.9485,-0.2755,-1.027],"max":[0.9305,0.884,0.663]},"volume_in3":1.1778,"centroid":[-0.0027,0.3548,-0.0018],"shell":[-0.0037,0.3532,-0.0314],"area_in2":13.0997,"triangles":8206,"manifold":true,"rail_seat":{"x":[-0.685,0.685],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-0.948,-0.256,-0.475,-0.573,0.884,0.653],[-0.573,-0.275,-1.027,0.555,0.884,0.663],[0.555,-0.256,-0.475,0.93,0.884,0.653]],"slots":["body","hardware","button"]},"guntec-ar15-carbine-buffer":{"part":"guntec-ar15-carbine-buffer","model":"guntec-ar15-carbine-buffer.glb","script":"guntec_ar15_carbine_buffer.py","inputs":{"guntec-ar15-carbine-buffer.body_length":3.02,"guntec-ar15-carbine-buffer.length":3.42,"guntec-ar15-carbine-buffer.od":0.98,"std.carbine_buffer.body_d":0.687,"std.carbine_buffer.body_start":0.5145,"std.carbine_buffer.bumper_band":0.06,"std.carbine_buffer.bumper_d":0.687,"std.carbine_buffer.bumper_exposed":0.4,"std.carbine_buffer.bumper_taper":13.5,"std.carbine_buffer.head_flat_across":0.952,"std.carbine_buffer.head_rim":0.214,"std.carbine_buffer.head_thickness":0.254,"std.carbine_buffer.pilot_d":0.781,"std.carbine_buffer.pilot_end":0.468,"std.carbine_buffer.pin_d":0.122,"std.carbine_buffer.pin_from_open_end":0.24},"profiles":{},"bounds":{"min":[0,-0.49,-0.49],"max":[3.42,0.462,0.49]},"volume_in3":1.3563,"centroid":[1.5468,0,0],"shell":[1.6809,0,0],"area_in2":10.0223,"triangles":7276,"manifold":true,"slabs":[[0,-0.49,-0.49,0.38,0.462,0.49],[0.38,-0.391,-0.391,3.42,0.391,0.391]],"slots":["body","bumper","pin"]},"guntec-ar15-castle-nut":{"part":"guntec-ar15-castle-nut","model":"guntec-ar15-castle-nut.glb","script":"guntec_ar15_castle_nut.py","inputs":{"guntec-ar15-castle-nut.edge_break":0.012,"guntec-ar15-castle-nut.hole_d":0.15,"guntec-ar15-castle-nut.hole_depth":0.085,"guntec-ar15-castle-nut.hole_from_front":0.133,"guntec-ar15-castle-nut.hole_round":44.5,"guntec-ar15-castle-nut.notch_depth":0.115,"guntec-ar15-castle-nut.notch_width":0.162,"guntec-ar15-castle-nut.notches":4,"guntec-ar15-castle-nut.od":1.355,"guntec-ar15-castle-nut.thickness":0.294,"std.receiver_extension.thread_major_d":1.1813},"profiles":{},"bounds":{"min":[0,-0.6775,-0.6775],"max":[0.294,0.6775,0.6775]},"volume_in3":0.0937,"centroid":[0.141,-0.0074,-0.0072],"shell":[0.1427,0.0008,0.0008],"area_in2":2.9642,"triangles":4028,"manifold":true,"slabs":[[0,-0.678,-0.587,0.294,-0.339,0.587],[0,-0.339,-0.678,0.294,0.339,0.678],[0,0.339,-0.587,0.294,0.678,0.587]],"slots":["nut"]},"guntec-ar15-chrome-silicon-buffer-spring":{"part":"guntec-ar15-chrome-silicon-buffer-spring","model":"guntec-ar15-chrome-silicon-buffer-spring.glb","script":"guntec_ar15_chrome_silicon_buffer_spring.py","inputs":{"guntec-ar15-chrome-silicon-buffer-spring.coils":39,"guntec-ar15-chrome-silicon-buffer-spring.free_length":11,"guntec-ar15-chrome-silicon-buffer-spring.installed_length":6.972,"guntec-ar15-chrome-silicon-buffer-spring.od":0.94,"guntec-ar15-chrome-silicon-buffer-spring.wire_d":0.072,"std.carbine_buffer.head_thickness":0.254,"std.carbine_buffer.pilot_d":0.781,"std.receiver_extension.bore_d":1},"profiles":{},"bounds":{"min":[0.254,-0.4719,-0.4719],"max":[7.226,0.4719,0.4719]},"volume_in3":0.4312,"centroid":[3.74,0,0],"shell":[3.74,0.0001,0],"area_in2":24.6378,"triangles":17484,"manifold":true,"slabs":[[0.254,-0.472,-0.472,7.226,0.472,0.472]],"slots":["spring"]},"guntec-ar15-end-plate":{"part":"guntec-ar15-end-plate","model":"guntec-ar15-end-plate.glb","script":"guntec_ar15_end_plate.py","inputs":{"guntec-ar15-end-plate.boss_below_axis":0.9974,"guntec-ar15-end-plate.boss_height":0.375,"guntec-ar15-end-plate.boss_proud":0.0645,"guntec-ar15-end-plate.boss_width":0.496,"guntec-ar15-end-plate.corner_angle":31.33,"guntec-ar15-end-plate.dimple_depth":0.063,"guntec-ar15-end-plate.dimple_grow":0.005,"guntec-ar15-end-plate.edge_break":0.012,"guntec-ar15-end-plate.hole_d":1.1902,"guntec-ar15-end-plate.key_tip_below_axis":0.5619,"guntec-ar15-end-plate.key_width":0.125,"guntec-ar15-end-plate.lobe_centre_below_axis":0.9522,"guntec-ar15-end-plate.lobe_radius":0.4266,"guntec-ar15-end-plate.relief_bottom_below_axis":0.6575,"guntec-ar15-end-plate.relief_fillet_r":0.031,"guntec-ar15-end-plate.relief_floor_half_width":0.1119,"guntec-ar15-end-plate.relief_top_half_width":0.354,"guntec-ar15-end-plate.side_angle":13.5,"guntec-ar15-end-plate.thickness":0.124,"guntec-ar15-end-plate.top_above_axis":0.6817,"std.receiver_extension.key_slot_floor":0.55,"std.receiver_extension.key_slot_width":0.125,"std.receiver_extension.thread_major_d":1.1813},"profiles":{},"bounds":{"min":[-0.0645,-1.3788,-0.6816],"max":[0.124,0.6817,0.6816]},"volume_in3":0.1191,"centroid":[0.0515,-0.5977,0.0003],"shell":[0.0541,-0.4761,0.0004],"area_in2":3.2758,"triangles":3460,"manifold":true,"slabs":[[-0.064,-1.379,-0.419,0.124,-1.035,0.419],[-0.064,-1.035,-0.501,0.124,-0.692,0.501],[0,-0.692,-0.586,0.124,-0.349,0.586],[0,-0.349,-0.682,0.124,0.338,0.682],[0,0.338,-0.592,0.124,0.682,0.592]],"slots":["plate"]},"guntec-ar15-heavy-duty-castle-nut":{"part":"guntec-ar15-heavy-duty-castle-nut","model":"guntec-ar15-heavy-duty-castle-nut.glb","script":"guntec_ar15_heavy_duty_castle_nut.py","inputs":{"guntec-ar15-heavy-duty-castle-nut.edge_break":0.012,"guntec-ar15-heavy-duty-castle-nut.notch_depth":0.078,"guntec-ar15-heavy-duty-castle-nut.notch_width":0.12,"guntec-ar15-heavy-duty-castle-nut.notches":4,"guntec-ar15-heavy-duty-castle-nut.od":1.3125,"guntec-ar15-heavy-duty-castle-nut.staking_notch_depth":0.03,"guntec-ar15-heavy-duty-castle-nut.staking_notch_radial":0.075,"guntec-ar15-heavy-duty-castle-nut.staking_notch_width":0.082,"guntec-ar15-heavy-duty-castle-nut.staking_notches":3,"guntec-ar15-heavy-duty-castle-nut.staking_round":45,"guntec-ar15-heavy-duty-castle-nut.thickness":0.375,"std.receiver_extension.thread_major_d":1.1813},"profiles":{},"bounds":{"min":[0,-0.6562,-0.6562],"max":[0.375,0.6562,0.6562]},"volume_in3":0.0934,"centroid":[0.1845,0,0],"shell":[0.1856,0,0],"area_in2":3.3984,"triangles":3916,"manifold":true,"slabs":[[0,-0.656,-0.568,0.375,-0.328,0.568],[0,-0.328,-0.656,0.375,0.328,0.656],[0,0.328,-0.568,0.375,0.656,0.568]],"slots":["nut"]},"guntec-ar15-mil-spec-buffer-tube-gen-2":{"part":"guntec-ar15-mil-spec-buffer-tube-gen-2","model":"guntec-ar15-mil-spec-buffer-tube-gen-2.glb","script":"guntec_ar15_mil_spec_buffer_tube_gen_2.py","inputs":{"guntec-ar15-mil-spec-buffer-tube-gen-2.channel_depth":0.03,"guntec-ar15-mil-spec-buffer-tube-gen-2.channel_front_from_rear":3.82,"guntec-ar15-mil-spec-buffer-tube-gen-2.channel_rear_from_rear":0.45,"guntec-ar15-mil-spec-buffer-tube-gen-2.channel_width":0.25,"guntec-ar15-mil-spec-buffer-tube-gen-2.position_hole_d":0.42,"guntec-ar15-mil-spec-buffer-tube-gen-2.position_hole_rear_from_rear":0.44,"guntec-ar15-mil-spec-buffer-tube-gen-2.position_step":0.66,"guntec-ar15-mil-spec-buffer-tube-gen-2.rail_rear_chamfer":0.1,"guntec-ar15-mil-spec-buffer-tube-gen-2.tube_front_behind_pin":0.669,"guntec-ar15-mil-spec-buffer-tube-gen-2.tube_length":7.25,"guntec-ar15-mil-spec-buffer-tube-gen-2.tube_od":1.148,"std.receiver_extension.bore_d":1,"std.receiver_extension.carbine_rear_wall":0.072,"std.receiver_extension.carbine_vent_d":0.094,"std.receiver_extension.key_slot_floor":0.55,"std.receiver_extension.key_slot_length":1.24,"std.receiver_extension.key_slot_width":0.125,"std.receiver_extension.rail_bottom_below_axis":0.874,"std.receiver_extension.rail_ramp_end":2.592,"std.receiver_extension.rail_ramp_start":2.326,"std.receiver_extension.rail_width":0.49,"std.receiver_extension.thread_length":1.181,"std.receiver_extension.thread_major_d":1.1813,"std.receiver_extension.thread_minor_d":1.1093,"std.receiver_extension.thread_pitch":0.0625},"profiles":{},"bounds":{"min":[0.669,-0.874,-0.5907],"max":[7.919,0.5907,0.5907]},"volume_in3":2.3431,"centroid":[4.6111,-0.1461,-0.0001],"shell":[4.41,-0.0798,-0.0001],"area_in2":58.7327,"triangles":30860,"manifold":true,"slabs":[[0.669,-0.587,-0.591,2.958,0.591,0.591],[2.958,-0.874,-0.574,7.919,0.574,0.574]],"slots":["tube"]},"guntec-ar15-stainless-carbine-buffer":{"part":"guntec-ar15-stainless-carbine-buffer","model":"guntec-ar15-stainless-carbine-buffer.glb","script":"guntec_ar15_stainless_carbine_buffer.py","inputs":{"guntec-ar15-stainless-carbine-buffer.length":3.251,"guntec-ar15-stainless-carbine-buffer.od":0.98,"std.carbine_buffer.body_d":0.687,"std.carbine_buffer.body_length":2.854,"std.carbine_buffer.body_start":0.5145,"std.carbine_buffer.bumper_band":0.06,"std.carbine_buffer.bumper_d":0.687,"std.carbine_buffer.bumper_exposed":0.4,"std.carbine_buffer.bumper_taper":13.5,"std.carbine_buffer.head_flat_across":0.952,"std.carbine_buffer.head_rim":0.214,"std.carbine_buffer.head_thickness":0.254,"std.carbine_buffer.pilot_d":0.781,"std.carbine_buffer.pilot_end":0.468,"std.carbine_buffer.pin_d":0.122,"std.carbine_buffer.pin_from_open_end":0.24},"profiles":{},"bounds":{"min":[0,-0.49,-0.49],"max":[3.251,0.462,0.49]},"volume_in3":1.2939,"centroid":[1.4641,0,0],"shell":[1.5949,0,0],"area_in2":9.6585,"triangles":7276,"manifold":true,"slabs":[[0,-0.49,-0.49,0.361,0.462,0.49],[0.361,-0.391,-0.391,3.251,0.391,0.391]],"slots":["body","bumper","pin"]},"hexmag-series-2-ar15-30":{"part":"hexmag-series-2-ar15-30","model":"hexmag-series-2-ar15-30.glb","script":"hexmag_series_2_ar15_30.py","inputs":{"hexmag-series-2-ar15-30.catch_notch_front_x":1.027,"hexmag-series-2-ar15-30.catch_notch_height":0.27,"hexmag-series-2-ar15-30.catch_notch_rear_x":0.507,"hexmag-series-2-ar15-30.catch_notch_top":1.057,"hexmag-series-2-ar15-30.floorplate_height":0.31,"hexmag-series-2-ar15-30.follower_thickness":0.06,"hexmag-series-2-ar15-30.grip_top":2.77,"hexmag-series-2-ar15-30.hex_band":0.081,"hexmag-series-2-ar15-30.hex_panels":28,"hexmag-series-2-ar15-30.hex_panels_front":2,"hexmag-series-2-ar15-30.hex_proud":0.03,"hexmag-series-2-ar15-30.hexid_across":0.474,"hexmag-series-2-ar15-30.hexid_depth":0.05,"hexmag-series-2-ar15-30.name_block_depth":0.01,"hexmag-series-2-ar15-30.overall_height":7.366,"hexmag-series-2-ar15-30.spine_depth":0.145,"hexmag-series-2-ar15-30.spine_width":0.457,"hexmag-series-2-ar15-30.vee_depth":0.04,"std.ar15.mag_catch_slot_floor":0.3799},"profiles":{"side":[[0,-0.483],[0.003,-1.869],[0.033,-2.618],[0.066,-3.063],[0.066,-3.099],[0.046,-3.119],[0.046,-3.155],[0.076,-3.195],[0.086,-3.363],[0.066,-3.386],[0.066,-3.409],[0.099,-3.462],[0.115,-3.624],[0.096,-3.643],[0.092,-3.67],[0.125,-3.716],[0.142,-3.864],[0.142,-3.888],[0.122,-3.911],[0.122,-3.94],[0.155,-3.983],[0.175,-4.151],[0.152,-4.181],[0.155,-4.207],[0.185,-4.234],[0.208,-4.409],[0.188,-4.435],[0.188,-4.465],[0.221,-4.498],[0.247,-4.676],[0.228,-4.696],[0.224,-4.712],[0.231,-4.735],[0.261,-4.762],[0.287,-4.923],[0.287,-4.937],[0.267,-4.956],[0.267,-4.979],[0.303,-5.026],[0.33,-5.184],[0.31,-5.23],[0.317,-5.253],[0.346,-5.28],[0.379,-5.454],[0.36,-5.477],[0.36,-5.504],[0.396,-5.54],[0.429,-5.708],[0.409,-5.751],[0.416,-5.774],[0.449,-5.811],[0.482,-5.969],[0.462,-6.012],[0.468,-6.032],[0.501,-6.061],[0.515,-6.114],[0.538,-6.22],[0.538,-6.236],[0.521,-6.256],[0.521,-6.279],[0.561,-6.322],[0.597,-6.487],[0.581,-6.513],[0.581,-6.536],[0.62,-6.576],[0.66,-6.744],[0.643,-6.771],[0.643,-6.79],[0.683,-6.84],[0.726,-7.001],[0.709,-7.025],[0.709,-7.051],[0.749,-7.091],[0.765,-7.147],[0.782,-7.209],[0.762,-7.242],[0.769,-7.265],[0.802,-7.295],[0.815,-7.345],[0.833,-7.366],[0.882,-7.356],[0.942,-7.363],[3.248,-6.729],[3.307,-6.69],[3.353,-6.68],[3.365,-6.649],[3.309,-6.451],[3.271,-6.413],[3.241,-6.409],[3.223,-6.391],[3.233,-6.355],[3.2,-6.312],[3.177,-6.226],[3.163,-6.17],[3.173,-6.154],[3.173,-6.121],[3.144,-6.091],[3.111,-5.956],[3.121,-5.9],[3.088,-5.854],[3.058,-5.718],[3.068,-5.669],[3.038,-5.633],[3.005,-5.484],[3.022,-5.451],[3.015,-5.431],[2.989,-5.405],[2.969,-5.316],[2.959,-5.253],[2.972,-5.223],[2.966,-5.2],[2.942,-5.177],[2.913,-5.026],[2.926,-5.009],[2.926,-4.983],[2.9,-4.95],[2.87,-4.798],[2.886,-4.772],[2.883,-4.748],[2.857,-4.719],[2.843,-4.65],[2.834,-4.584],[2.843,-4.521],[2.817,-4.491],[2.794,-4.346],[2.81,-4.306],[2.801,-4.277],[2.781,-4.257],[2.761,-4.115],[2.774,-4.085],[2.774,-4.059],[2.748,-4.026],[2.731,-3.907],[2.728,-3.871],[2.745,-3.851],[2.745,-3.835],[2.741,-3.818],[2.718,-3.795],[2.702,-3.66],[2.702,-3.637],[2.715,-3.624],[2.715,-3.591],[2.692,-3.564],[2.688,-3.544],[2.675,-3.406],[2.692,-3.386],[2.692,-3.366],[2.669,-3.333],[2.659,-3.264],[2.652,-3.175],[2.669,-3.155],[2.669,-3.129],[2.646,-3.099],[2.642,-3.076],[2.632,-2.944],[2.649,-2.924],[2.649,-2.898],[2.626,-2.868],[2.616,-2.687],[2.533,-2.575],[2.53,-0.328],[2.517,-0.315],[2.514,-0.229],[2.03,-0.228],[1.968,-0.208],[1.948,-0.224],[1.912,-0.191],[1.889,-0.185],[1.897,-0.2],[1.869,-0.228],[1.842,-0.228],[1.829,-0.214],[1.773,-0.214],[1.76,-0.228],[1.74,-0.228],[1.72,-0.214],[1.654,-0.218],[1.476,-0.175],[1.377,-0.132],[1.268,-0.069],[1.25,-0.051],[1.255,-0.043],[1.229,-0.043],[1.176,0],[0.17,-0.003],[0.148,-0.038],[0.145,-0.209],[0.127,-0.228],[0.096,-0.233],[0.092,-0.345],[0.036,-0.407],[0.033,-0.463],[0.015,-0.482]],"right":[[0,-0.48],[0,-1.809],[0.03,-2.626],[0.063,-3.055],[0.063,-3.101],[0.043,-3.121],[0.04,-3.144],[0.073,-3.187],[0.086,-3.358],[0.066,-3.381],[0.063,-3.408],[0.096,-3.451],[0.112,-3.622],[0.092,-3.642],[0.089,-3.668],[0.122,-3.714],[0.138,-3.886],[0.119,-3.909],[0.119,-3.932],[0.152,-3.975],[0.155,-3.998],[0.171,-4.146],[0.148,-4.186],[0.155,-4.209],[0.181,-4.232],[0.208,-4.407],[0.185,-4.433],[0.185,-4.456],[0.218,-4.496],[0.231,-4.578],[0.241,-4.671],[0.224,-4.69],[0.224,-4.723],[0.257,-4.763],[0.284,-4.928],[0.264,-4.954],[0.264,-4.98],[0.297,-5.017],[0.326,-5.185],[0.31,-5.208],[0.307,-5.234],[0.313,-5.254],[0.343,-5.277],[0.373,-5.429],[0.376,-5.452],[0.356,-5.472],[0.356,-5.505],[0.392,-5.541],[0.425,-5.706],[0.406,-5.736],[0.406,-5.759],[0.442,-5.798],[0.478,-5.97],[0.458,-6.009],[0.465,-6.032],[0.498,-6.062],[0.534,-6.23],[0.514,-6.253],[0.514,-6.276],[0.557,-6.329],[0.594,-6.484],[0.574,-6.51],[0.574,-6.53],[0.58,-6.547],[0.613,-6.573],[0.623,-6.606],[0.656,-6.744],[0.64,-6.761],[0.636,-6.784],[0.643,-6.804],[0.676,-6.83],[0.719,-6.995],[0.702,-7.025],[0.706,-7.051],[0.745,-7.091],[0.778,-7.206],[0.758,-7.246],[0.765,-7.265],[0.801,-7.298],[0.818,-7.354],[0.836,-7.366],[0.879,-7.353],[0.938,-7.359],[2.072,-7.049],[2.155,-7.02],[3.256,-6.726],[3.296,-6.693],[3.352,-6.677],[3.36,-6.642],[3.31,-6.461],[3.259,-6.407],[3.24,-6.407],[3.221,-6.388],[3.231,-6.372],[3.228,-6.349],[3.195,-6.309],[3.159,-6.167],[3.172,-6.138],[3.165,-6.115],[3.139,-6.085],[3.106,-5.947],[3.116,-5.923],[3.113,-5.887],[3.086,-5.864],[3.057,-5.742],[3.05,-5.709],[3.063,-5.693],[3.063,-5.676],[3.033,-5.633],[3.014,-5.548],[3.004,-5.478],[3.014,-5.445],[2.981,-5.389],[2.954,-5.257],[2.968,-5.218],[2.938,-5.172],[2.911,-5.037],[2.925,-4.994],[2.918,-4.971],[2.895,-4.951],[2.869,-4.806],[2.882,-4.76],[2.852,-4.713],[2.836,-4.621],[2.829,-4.562],[2.842,-4.529],[2.813,-4.476],[2.793,-4.347],[2.806,-4.298],[2.78,-4.252],[2.76,-4.113],[2.773,-4.064],[2.75,-4.031],[2.74,-3.975],[2.727,-3.873],[2.74,-3.859],[2.743,-3.83],[2.717,-3.787],[2.7,-3.645],[2.717,-3.602],[2.691,-3.563],[2.687,-3.54],[2.677,-3.404],[2.691,-3.388],[2.691,-3.368],[2.667,-3.338],[2.654,-3.177],[2.667,-3.16],[2.667,-3.127],[2.644,-3.098],[2.631,-2.949],[2.648,-2.93],[2.648,-2.893],[2.625,-2.864],[2.615,-2.686],[2.532,-2.577],[2.536,-0.338],[2.519,-0.298],[2.519,-0.232],[2.076,-0.231],[2.013,-0.228],[1.98,-0.214],[1.957,-0.231],[1.931,-0.201],[1.911,-0.195],[1.902,-0.196],[1.916,-0.209],[1.884,-0.231],[1.861,-0.211],[1.841,-0.231],[1.713,-0.228],[1.683,-0.204],[1.647,-0.208],[1.637,-0.218],[1.624,-0.208],[1.584,-0.208],[1.479,-0.178],[1.377,-0.135],[1.284,-0.082],[1.266,-0.064],[1.278,-0.046],[1.232,-0.049],[1.166,0],[0.186,0],[0.16,-0.013],[0.152,-0.035],[0.148,-0.206],[0.127,-0.228],[0.096,-0.232],[0.092,-0.341],[0.04,-0.404],[0.036,-0.46],[0.015,-0.481]],"rear":[[-0.542,-6.685],[-0.542,-7.252],[-0.526,-7.289],[-0.495,-7.31],[-0.406,-7.33],[-0.336,-7.336],[-0.31,-7.353],[-0.267,-7.359],[-0.211,-7.353],[-0.148,-7.363],[-0.109,-7.359],[0.036,-7.366],[0.109,-7.359],[0.142,-7.363],[0.208,-7.353],[0.257,-7.359],[0.31,-7.353],[0.336,-7.336],[0.458,-7.32],[0.519,-7.295],[0.542,-7.249],[0.542,-6.698],[0.509,-6.636],[0.467,-6.596],[0.463,-6.533],[0.467,-2.824],[0.463,-2.785],[0.437,-2.745],[0.44,-0.203],[0.424,-0.137],[0.394,-0.087],[0.369,-0.059],[0.31,-0.02],[0.257,-0.003],[0.224,0],[0.226,-0.031],[0.208,-0.049],[0.148,-0.043],[0.134,-0.054],[0.171,-0.056],[0.188,-0.073],[0.208,-0.056],[0.226,-0.074],[0.226,-0.163],[0.213,-0.176],[0.223,-0.186],[0.223,-0.203],[0.204,-0.221],[0.188,-0.204],[0.181,-0.211],[0.162,-0.208],[0.142,-0.228],[0.115,-0.208],[0.079,-0.208],[0.084,-0.219],[0.066,-0.237],[0.049,-0.237],[0.028,-0.216],[0.033,-0.208],[0,-0.208],[-0.016,-0.191],[-0.049,-0.228],[-0.129,-0.224],[-0.158,-0.241],[-0.175,-0.224],[-0.201,-0.228],[-0.219,-0.209],[-0.223,-0.002],[-0.244,0],[-0.277,-0.007],[-0.333,-0.03],[-0.384,-0.071],[-0.424,-0.134],[-0.437,-0.173],[-0.443,-0.223],[-0.443,-2.709],[-0.447,-2.745],[-0.47,-2.781],[-0.473,-2.831],[-0.473,-6.596],[-0.513,-6.632]]},"features":{"side":{"hexes":[[[0.299,-2.077],[0.533,-2.301],[0.536,-2.317],[0.454,-2.614],[0.427,-2.631],[0.19,-2.693],[0.18,-2.654],[0.18,-2.624],[0.186,-2.618],[0.18,-2.581],[0.18,-2.113],[0.216,-2.096]],[[1.413,-1.78],[1.641,-2.001],[1.644,-2.024],[1.572,-2.301],[1.555,-2.327],[1.249,-2.41],[1.018,-2.182],[1.021,-2.146],[1.09,-1.885],[1.11,-1.859]],[[0.945,-2.248],[1.179,-2.482],[1.1,-2.779],[1.087,-2.796],[0.8,-2.875],[0.777,-2.875],[0.549,-2.651],[0.553,-2.604],[0.622,-2.35],[0.635,-2.331]],[[0.477,-2.716],[0.691,-2.928],[0.684,-2.934],[0.708,-2.957],[0.704,-2.98],[0.694,-2.99],[0.698,-3],[0.632,-3.244],[0.619,-3.264],[0.308,-3.347],[0.256,-3.297],[0.236,-3.079],[0.242,-3.069],[0.206,-3.027],[0.213,-3.02],[0.203,-3.007],[0.19,-2.796],[0.203,-2.786]],[[2.057,-1.954],[2.284,-2.185],[2.208,-2.479],[2.189,-2.499],[1.951,-2.565],[1.941,-2.558],[1.931,-2.568],[1.892,-2.578],[1.658,-2.35],[1.658,-2.331],[1.737,-2.044],[1.747,-2.034],[1.78,-2.02],[1.803,-2.034],[1.826,-2.011],[1.895,-1.994],[1.915,-1.997],[1.935,-1.984]],[[1.588,-2.42],[1.816,-2.644],[1.819,-2.664],[1.803,-2.726],[1.78,-2.756],[1.79,-2.766],[1.786,-2.792],[1.776,-2.802],[1.78,-2.812],[1.747,-2.937],[1.73,-2.967],[1.423,-3.05],[1.189,-2.815],[1.265,-2.515],[1.275,-2.502]],[[1.117,-2.888],[1.156,-2.918],[1.341,-3.102],[1.351,-3.119],[1.272,-3.422],[1.255,-3.439],[0.952,-3.518],[0.717,-3.287],[0.717,-3.271],[0.787,-3.01],[0.803,-2.97],[0.948,-2.947],[0.975,-2.924]],[[0.645,-3.353],[0.714,-3.413],[0.876,-3.574],[0.879,-3.607],[0.793,-3.904],[0.477,-3.986],[0.308,-3.818],[0.285,-3.591],[0.318,-3.462],[0.341,-3.432]],[[2.232,-2.594],[2.456,-2.822],[2.38,-3.119],[2.364,-3.135],[2.067,-3.218],[1.829,-2.994],[1.826,-2.974],[1.836,-2.934],[1.865,-2.905],[1.862,-2.845],[1.905,-2.697],[1.918,-2.674],[1.938,-2.667],[1.945,-2.674],[1.964,-2.66]],[[1.76,-3.056],[1.806,-3.093],[1.991,-3.284],[1.935,-3.521],[1.908,-3.548],[1.915,-3.597],[1.898,-3.614],[1.856,-3.627],[1.842,-3.62],[1.595,-3.69],[1.367,-3.469],[1.357,-3.449],[1.437,-3.152],[1.453,-3.135]],[[1.291,-3.525],[1.509,-3.739],[1.522,-3.769],[1.443,-4.066],[1.423,-4.082],[1.13,-4.161],[1.1,-4.142],[0.889,-3.927],[0.962,-3.64],[0.968,-3.62],[0.985,-3.604]],[[0.823,-3.996],[1.054,-4.231],[0.975,-4.534],[0.952,-4.554],[0.651,-4.63],[0.421,-4.402],[0.417,-4.386],[0.5,-4.089],[0.516,-4.076]],[[2.403,-3.234],[2.522,-3.36],[2.561,-3.723],[2.555,-3.756],[2.525,-3.785],[2.238,-3.861],[2.011,-3.637],[2.004,-3.607],[2.011,-3.584],[2.024,-3.571],[2.027,-3.525],[2.09,-3.314]],[[1.921,-3.699],[1.945,-3.723],[1.951,-3.719],[2.149,-3.917],[2.159,-3.937],[2.11,-4.125],[2.093,-4.148],[2.096,-4.171],[2.077,-4.237],[2.063,-4.25],[2.02,-4.264],[2.007,-4.254],[1.987,-4.273],[1.945,-4.287],[1.931,-4.283],[1.915,-4.297],[1.766,-4.333],[1.536,-4.109],[1.529,-4.085],[1.605,-3.805],[1.621,-3.779]],[[1.463,-4.168],[1.694,-4.399],[1.694,-4.419],[1.615,-4.706],[1.598,-4.722],[1.295,-4.801],[1.064,-4.574],[1.064,-4.541],[1.14,-4.264],[1.153,-4.25]],[[0.995,-4.64],[1.225,-4.871],[1.153,-5.154],[1.133,-5.191],[0.823,-5.27],[0.592,-5.039],[0.658,-4.765],[0.671,-4.729],[0.688,-4.715]],[[2.571,-3.874],[2.581,-3.884],[2.657,-4.429],[2.641,-4.438],[2.403,-4.498],[2.175,-4.27],[2.255,-3.967],[2.268,-3.953]],[[2.1,-4.343],[2.327,-4.567],[2.331,-4.584],[2.258,-4.857],[2.241,-4.887],[2.212,-4.89],[2.133,-4.92],[2.113,-4.913],[2.09,-4.933],[1.938,-4.973],[1.704,-4.742],[1.704,-4.715],[1.776,-4.452],[1.793,-4.422],[1.931,-4.382],[1.945,-4.386],[1.981,-4.369],[2.007,-4.366],[2.017,-4.376],[2.037,-4.356]],[[1.641,-4.811],[1.869,-5.042],[1.786,-5.349],[1.763,-5.365],[1.466,-5.441],[1.232,-5.204],[1.311,-4.904],[1.331,-4.887],[1.611,-4.811]],[[1.159,-5.276],[1.397,-5.507],[1.397,-5.527],[1.321,-5.804],[1.305,-5.83],[0.998,-5.913],[0.77,-5.689],[0.764,-5.666],[0.84,-5.382],[0.856,-5.359]],[[2.667,-4.534],[2.68,-4.564],[2.769,-5.085],[2.68,-5.115],[2.575,-5.138],[2.347,-4.91],[2.426,-4.607],[2.462,-4.587]],[[2.271,-4.983],[2.502,-5.214],[2.426,-5.51],[2.41,-5.53],[2.354,-5.547],[2.337,-5.543],[2.327,-5.553],[2.251,-5.576],[2.238,-5.567],[2.218,-5.586],[2.172,-5.6],[2.159,-5.596],[2.126,-5.613],[2.103,-5.613],[1.875,-5.375],[1.948,-5.088],[1.964,-5.062],[2.04,-5.039],[2.053,-5.042],[2.106,-5.022],[2.126,-5.032],[2.143,-5.016],[2.222,-4.996],[2.232,-4.999]],[[1.813,-5.451],[2.037,-5.679],[2.04,-5.689],[1.961,-5.989],[1.948,-6.002],[1.641,-6.084],[1.407,-5.854],[1.483,-5.547],[1.496,-5.53],[1.776,-5.454]],[[1.331,-5.92],[1.348,-5.926],[1.562,-6.141],[1.569,-6.17],[1.489,-6.461],[1.479,-6.47],[1.169,-6.553],[0.942,-6.329],[0.935,-6.315],[1.008,-6.038],[1.028,-6.002]],[[2.786,-5.187],[2.796,-5.2],[2.815,-5.319],[2.908,-5.735],[2.895,-5.745],[2.773,-5.778],[2.746,-5.778],[2.525,-5.56],[2.519,-5.543],[2.601,-5.243],[2.634,-5.227]],[[2.446,-5.626],[2.674,-5.85],[2.67,-5.887],[2.601,-6.141],[2.585,-6.17],[2.492,-6.197],[2.482,-6.19],[2.466,-6.203],[2.403,-6.223],[2.383,-6.216],[2.367,-6.233],[2.314,-6.249],[2.307,-6.243],[2.281,-6.256],[2.05,-6.028],[2.05,-5.992],[2.119,-5.735],[2.139,-5.702],[2.238,-5.675],[2.255,-5.685],[2.271,-5.669],[2.35,-5.649],[2.36,-5.656],[2.37,-5.646]],[[2.152,-6.263],[2.152,-6.282],[2.129,-6.299],[1.625,-6.434],[1.611,-6.431],[1.598,-6.414],[1.651,-6.197],[1.667,-6.174],[1.978,-6.091]],[[2.921,-5.84],[2.934,-5.85],[3.027,-6.239],[3.066,-6.378],[3.053,-6.391],[2.944,-6.421],[2.921,-6.421],[2.693,-6.193],[2.773,-5.887],[2.806,-5.87]]],"hexes_front":[[[2.347,-0.846],[2.426,-0.922],[2.423,-1.397],[2.413,-1.41],[2.189,-1.47],[1.954,-1.235],[2.034,-0.938],[2.047,-0.925]],[[2.416,-1.516],[2.423,-1.522],[2.426,-1.925],[2.436,-2.083],[2.413,-2.096],[2.357,-2.106],[2.126,-1.872],[2.208,-1.575],[2.225,-1.562]]],"notch":[[[1.014,-1.133],[1.018,-1.328],[0.988,-1.357],[0.553,-1.357],[0.523,-1.334],[0.52,-1.146],[0.546,-1.113],[0.985,-1.11]]],"notch_block":[[[0.909,-1.39],[0.909,-1.456],[0.899,-1.466],[0.642,-1.466],[0.632,-1.456],[0.635,-1.39],[0.645,-1.381],[0.899,-1.381]],[[0.952,-1.549],[0.942,-1.562],[0.599,-1.562],[0.589,-1.552],[0.625,-1.486],[0.648,-1.47],[0.902,-1.47]]],"vees":[[[2.347,-0.51],[2.331,-0.52],[1.964,-0.421],[1.954,-0.411],[1.964,-0.401],[2.34,-0.401],[2.35,-0.411]],[[1.915,-0.734],[1.921,-0.579],[1.931,-0.569],[2.208,-0.642],[2.228,-0.655],[2.199,-0.671],[1.928,-0.744]]],"above_step":[[[2.782,-2.662],[-0.186,-2.922],[-0.186,0.078],[2.782,0.078]]]},"right":{"hexes":[[[0.298,-2.076],[0.18,-2.109],[0.18,-2.669],[0.19,-2.695],[0.43,-2.63],[0.453,-2.61],[0.529,-2.316],[0.519,-2.29]],[[1.416,-1.782],[1.403,-1.779],[1.106,-1.858],[1.09,-1.874],[1.011,-2.178],[1.241,-2.409],[1.548,-2.329],[1.561,-2.316],[1.64,-2.006]],[[0.935,-2.247],[0.635,-2.326],[0.615,-2.359],[0.539,-2.643],[0.546,-2.656],[0.773,-2.877],[0.806,-2.874],[1.08,-2.798],[1.093,-2.785],[1.169,-2.508],[1.172,-2.478],[0.951,-2.254]],[[0.473,-2.719],[0.203,-2.785],[0.19,-2.794],[0.203,-3.012],[0.219,-3.029],[0.213,-3.042],[0.239,-3.071],[0.232,-3.081],[0.252,-3.296],[0.298,-3.345],[0.321,-3.345],[0.605,-3.269],[0.622,-3.256],[0.691,-3.005],[0.684,-2.992],[0.704,-2.959],[0.684,-2.939],[0.687,-2.93]],[[2.053,-1.954],[1.937,-1.98],[1.907,-1.996],[1.894,-1.993],[1.832,-2.006],[1.802,-2.029],[1.789,-2.02],[1.752,-2.026],[1.726,-2.056],[1.654,-2.329],[1.654,-2.353],[1.884,-2.58],[1.927,-2.57],[1.937,-2.56],[1.95,-2.564],[2.191,-2.498],[2.204,-2.481],[2.277,-2.217],[2.28,-2.178]],[[1.584,-2.422],[1.551,-2.425],[1.274,-2.501],[1.261,-2.514],[1.182,-2.817],[1.413,-3.052],[1.72,-2.972],[1.736,-2.953],[1.776,-2.811],[1.769,-2.801],[1.782,-2.788],[1.785,-2.768],[1.776,-2.755],[1.795,-2.735],[1.815,-2.656],[1.812,-2.646]],[[1.113,-2.89],[0.974,-2.923],[0.945,-2.949],[0.8,-2.972],[0.79,-2.986],[0.711,-3.269],[0.714,-3.292],[0.951,-3.52],[1.248,-3.441],[1.271,-3.408],[1.347,-3.131],[1.34,-3.111]],[[0.641,-3.355],[0.335,-3.434],[0.318,-3.454],[0.289,-3.559],[0.282,-3.615],[0.305,-3.817],[0.476,-3.985],[0.783,-3.906],[0.803,-3.869],[0.872,-3.619],[0.875,-3.582]],[[2.227,-2.597],[1.97,-2.659],[1.94,-2.676],[1.917,-2.672],[1.901,-2.695],[1.855,-2.854],[1.858,-2.907],[1.832,-2.933],[1.822,-2.972],[1.828,-3.002],[2.056,-3.216],[2.366,-3.137],[2.382,-3.104],[2.442,-2.89],[2.455,-2.821]],[[1.749,-3.058],[1.449,-3.137],[1.429,-3.157],[1.354,-3.447],[1.357,-3.464],[1.591,-3.691],[1.832,-3.629],[1.841,-3.619],[1.855,-3.625],[1.894,-3.612],[1.911,-3.596],[1.904,-3.549],[1.931,-3.523],[1.987,-3.302],[1.983,-3.282],[1.868,-3.17],[1.802,-3.094]],[[1.281,-3.526],[0.978,-3.606],[0.958,-3.638],[0.885,-3.925],[1.113,-4.156],[1.136,-4.156],[1.419,-4.08],[1.436,-4.067],[1.518,-3.76],[1.307,-3.543]],[[0.816,-3.995],[0.757,-4.004],[0.506,-4.074],[0.486,-4.107],[0.414,-4.394],[0.641,-4.624],[0.668,-4.624],[0.958,-4.545],[0.974,-4.516],[1.047,-4.225]],[[2.392,-3.233],[2.089,-3.315],[2.072,-3.345],[2.02,-3.543],[2.023,-3.573],[2.006,-3.589],[2,-3.629],[2.231,-3.856],[2.534,-3.777],[2.547,-3.764],[2.557,-3.695],[2.521,-3.358]],[[1.914,-3.701],[1.617,-3.777],[1.601,-3.797],[1.528,-4.067],[1.528,-4.103],[1.756,-4.328],[1.983,-4.272],[2.003,-4.252],[2.013,-4.262],[2.062,-4.245],[2.076,-4.232],[2.092,-4.176],[2.089,-4.143],[2.105,-4.126],[2.151,-3.958],[2.155,-3.929],[1.947,-3.721],[1.937,-3.724]],[[1.456,-4.166],[1.149,-4.245],[1.133,-4.265],[1.057,-4.568],[1.288,-4.799],[1.594,-4.72],[1.614,-4.694],[1.69,-4.41],[1.687,-4.394]],[[0.994,-4.638],[0.981,-4.634],[0.678,-4.713],[0.658,-4.753],[0.585,-5.033],[0.819,-5.267],[1.126,-5.188],[1.142,-5.172],[1.218,-4.865]],[[2.56,-3.873],[2.267,-3.952],[2.25,-3.968],[2.181,-4.225],[2.178,-4.275],[2.402,-4.496],[2.643,-4.436],[2.656,-4.427],[2.603,-4.09],[2.58,-3.889]],[[2.092,-4.341],[2.033,-4.354],[2.013,-4.374],[2,-4.361],[1.95,-4.374],[1.94,-4.384],[1.927,-4.38],[1.792,-4.417],[1.776,-4.433],[1.696,-4.727],[1.703,-4.746],[1.931,-4.971],[2.089,-4.931],[2.109,-4.911],[2.125,-4.918],[2.201,-4.898],[2.211,-4.888],[2.24,-4.885],[2.254,-4.862],[2.326,-4.591],[2.326,-4.565],[2.161,-4.4]],[[1.624,-4.806],[1.324,-4.885],[1.304,-4.908],[1.228,-5.188],[1.232,-5.215],[1.459,-5.439],[1.766,-5.36],[1.785,-5.337],[1.855,-5.076],[1.858,-5.033],[1.667,-4.839]],[[1.156,-5.274],[0.852,-5.356],[0.836,-5.376],[0.76,-5.679],[0.988,-5.907],[1.014,-5.907],[1.297,-5.831],[1.317,-5.805],[1.393,-5.518],[1.39,-5.501]],[[2.669,-4.532],[2.442,-4.591],[2.428,-4.601],[2.346,-4.895],[2.349,-4.915],[2.58,-5.139],[2.758,-5.093],[2.768,-5.083],[2.679,-4.555]],[[2.264,-4.98],[2.24,-4.987],[2.227,-5],[2.217,-4.994],[2.145,-5.01],[2.122,-5.03],[2.102,-5.02],[1.96,-5.06],[1.947,-5.079],[1.874,-5.343],[1.871,-5.383],[2.102,-5.61],[2.145,-5.604],[2.158,-5.59],[2.171,-5.597],[2.217,-5.584],[2.237,-5.564],[2.247,-5.574],[2.326,-5.551],[2.336,-5.541],[2.349,-5.544],[2.409,-5.528],[2.428,-5.498],[2.494,-5.248],[2.498,-5.205],[2.283,-4.99]],[[1.802,-5.449],[1.492,-5.528],[1.479,-5.541],[1.4,-5.841],[1.403,-5.851],[1.634,-6.082],[1.944,-5.999],[1.96,-5.973],[2.036,-5.693],[2.023,-5.663]],[[1.334,-5.917],[1.027,-5.996],[1.007,-6.022],[0.931,-6.309],[0.938,-6.329],[1.166,-6.553],[1.472,-6.471],[1.485,-6.458],[1.565,-6.164],[1.561,-6.144]],[[2.785,-5.188],[2.616,-5.231],[2.593,-5.248],[2.517,-5.538],[2.521,-5.554],[2.735,-5.768],[2.755,-5.778],[2.893,-5.742],[2.903,-5.732],[2.827,-5.389],[2.794,-5.205]],[[2.445,-5.623],[2.369,-5.64],[2.359,-5.65],[2.28,-5.663],[2.254,-5.683],[2.234,-5.673],[2.191,-5.683],[2.178,-5.696],[2.168,-5.689],[2.135,-5.699],[2.118,-5.719],[2.049,-5.983],[2.046,-6.026],[2.283,-6.256],[2.306,-6.243],[2.32,-6.247],[2.362,-6.233],[2.382,-6.214],[2.392,-6.224],[2.471,-6.2],[2.481,-6.191],[2.491,-6.194],[2.583,-6.167],[2.597,-6.144],[2.676,-5.858],[2.669,-5.844]],[[2.151,-6.27],[1.983,-6.095],[1.954,-6.092],[1.663,-6.171],[1.647,-6.2],[1.594,-6.411],[1.611,-6.431],[2.132,-6.296]],[[2.92,-5.838],[2.781,-5.874],[2.771,-5.884],[2.689,-6.187],[2.91,-6.415],[2.93,-6.421],[3.052,-6.388],[3.058,-6.372],[2.933,-5.848]]],"hexes_front":[[[2.349,-0.846],[2.046,-0.925],[2.033,-0.941],[1.96,-1.205],[1.957,-1.245],[2.188,-1.469],[2.422,-1.403],[2.428,-0.922]],[[2.415,-1.512],[2.217,-1.565],[2.207,-1.574],[2.125,-1.871],[2.359,-2.109],[2.435,-2.085],[2.425,-1.835],[2.425,-1.551]]],"vees":[[[1.96,-0.414],[1.97,-0.424],[2.329,-0.519],[2.349,-0.509],[2.353,-0.414],[2.343,-0.404],[1.97,-0.404]],[[1.914,-0.734],[1.931,-0.744],[2.211,-0.668],[2.231,-0.654],[2.221,-0.645],[1.931,-0.569],[1.921,-0.579]]],"name_block":[[[0.434,-0.457],[0.427,-0.476],[0.427,-0.958],[0.434,-0.974],[0.467,-1.004],[1.548,-1.007],[1.571,-0.994],[1.594,-0.964],[1.598,-0.483],[1.588,-0.457],[1.558,-0.43],[1.528,-0.424],[0.486,-0.424],[0.46,-0.43]]]},"rear":{}},"placement":{"side":{"plane":"xy","offset":{}},"right":{"plane":"xy","offset":{}},"rear":{"plane":"zy","offset":{}}},"bounds":{"min":[0,-7.366,-0.542],"max":[3.365,0,0.542]},"volume_in3":16.0361,"centroid":[1.4921,-3.7374,-0.0032],"shell":[1.4921,-3.5544,-0.0038],"area_in2":62.492,"triangles":4960,"manifold":true,"slabs":[[0.709,-7.366,-0.542,2.341,-6.978,0.542],[0.623,-6.978,-0.542,3.365,-6.591,0.542],[0.521,-6.591,-0.542,3.348,-6.203,0.542],[0.45,-6.203,-0.473,3.173,-5.815,0.464],[0.36,-5.815,-0.473,3.079,-5.428,0.464],[0.305,-5.428,-0.473,3.012,-5.04,0.465],[0.224,-5.04,-0.473,2.926,-4.652,0.465],[0.188,-4.652,-0.473,2.843,-4.265,0.465],[0.092,-4.265,-0.473,2.789,-3.489,0.466],[0.04,-3.489,-0.473,2.692,-2.714,0.467],[0.021,-2.714,-0.473,2.617,-2.326,0.465],[0,-2.326,-0.443,2.533,-0.388,0.44],[0.053,-0.388,-0.443,2.53,0,0.44]],"slots":["body","hexid"]},"holosun-aro-163-mount":{"part":"holosun-aro-163-mount","model":"holosun-aro-163-mount.glb","script":"holosun_aro.py","inputs":{"holosun-aro-163-mount.deck_above_rail":0.728,"holosun-aro-163-mount.deck_x":0.01,"holosun-aro.barrel_od":1.2,"holosun-aro.bolt_head_d":0.348,"holosun-aro.bolt_thread_d":0.18,"holosun-aro.bolt_tip_z":0.94,"holosun-aro.button_d":0.357,"holosun-aro.button_mark_length":0.23,"holosun-aro.button_mark_width":0.044,"holosun-aro.button_minus_x":0.068,"holosun-aro.button_plus_x":0.61,"holosun-aro.button_ring_width":0.02,"holosun-aro.cap_d":0.534,"holosun-aro.cap_slot_length":0.24,"holosun-aro.cap_slot_width":0.04,"holosun-aro.clamp_bottom_y":-0.227,"holosun-aro.clamp_corner_chamfer":0.05,"holosun-aro.clamp_flank_end_y":0.02,"holosun-aro.clamp_flank_top_y":0.197,"holosun-aro.clamp_flat_length":0.413,"holosun-aro.clamp_saddle_width":0.144,"holosun-aro.clamp_top_end_y":0.107,"holosun-aro.clamp_top_y":0.28,"holosun-aro.cover_bottom_y":0.927,"holosun-aro.cover_corner_r":0.13,"holosun-aro.cover_front_x":0.8,"holosun-aro.cover_proud":0.035,"holosun-aro.cover_rear_x":-0.52,"holosun-aro.cover_screw_front_x":0.652,"holosun-aro.cover_screw_head_d":0.165,"holosun-aro.cover_screw_rear_x":-0.352,"holosun-aro.cover_screw_y":1.01,"holosun-aro.cover_top_y":1.23,"holosun-aro.cross_bolt_x":0.01,"holosun-aro.cross_bolt_y":0.015,"holosun-aro.deck_foot_width":0.739,"holosun-aro.deck_front_x":0.977,"holosun-aro.deck_top_front_y":2.29,"holosun-aro.deck_top_rear_y":2.376,"holosun-aro.deck_top_width":0.65,"holosun-aro.detail_relief":0.02,"holosun-aro.eyepiece_od":1.094,"holosun-aro.flute_bottom_y":1.875,"holosun-aro.flute_front_x":0.94,"holosun-aro.flute_rear_x":-0.92,"holosun-aro.flute_top_y":2.15,"holosun-aro.housing_front_x":1.055,"holosun-aro.housing_rear_x":-1.028,"holosun-aro.length":2.48,"holosun-aro.logo_height":0.245,"holosun-aro.logo_left_mid_x":0.036,"holosun-aro.logo_length":1.042,"holosun-aro.logo_mid_y":1.64,"holosun-aro.logo_right_mid_x":0.373,"holosun-aro.mount_length":1.486,"holosun-aro.mount_rise":0.728,"holosun-aro.nut_across_flats":0.375,"holosun-aro.nut_outer_z":0.867,"holosun-aro.nut_recess_d":0.48,"holosun-aro.nut_recess_depth":0.08,"holosun-aro.nut_recess_wing_bottom_y":-0.006,"holosun-aro.nut_recess_wing_length":0.829,"holosun-aro.nut_recess_wing_top_y":0.11,"holosun-aro.nut_seat_z":0.641,"holosun-aro.optical_axis_above_rail":1.63,"holosun-aro.pad_front_x":0.89,"holosun-aro.pad_proud":0.012,"holosun-aro.pad_rear_x":-0.23,"holosun-aro.pad_width":0.55,"holosun-aro.rear_behind_clamp_middle":1.115,"holosun-aro.skirt_bottom_front_x":0.806,"holosun-aro.skirt_bottom_rear_x":-0.771,"holosun-aro.skirt_bottom_width":0.894,"holosun-aro.skirt_chamfer_top_y":0.89,"holosun-aro.skirt_shoulder_y":1.3,"holosun-aro.skirt_top_y":1.22,"holosun-aro.skirt_width":1.094,"holosun-aro.stem_end_width":0.136,"holosun-aro.stem_foot_y":0.327,"holosun-aro.stem_length":0.935,"holosun-aro.stem_panel_length":0.475,"holosun-aro.stem_width":0.273,"holosun-aro.top_above_axis":0.78,"holosun-aro.tube_od":1.17,"holosun-aro.turret_x":-0.57,"holosun-aro.windage_boss_d":0.66,"holosun-aro.windage_boss_reach_z":0.73,"holosun-aro.windage_cap_reach_z":0.78,"holosun-aro.windage_y":1.63,"holosun-aro.window":0.866,"holosun-aro.window_d":0.737,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{},"features":{},"placement":{},"bounds":{"min":[-0.733,-0.227,-0.5842],"max":[0.753,0.728,0.94]},"volume_in3":0.625,"centroid":[0.0099,0.1308,0.0654],"shell":[0.0099,0.1045,0.0768],"area_in2":7.2764,"triangles":1498,"manifold":true,"rail_seat":{"x":[-0.733,0.753],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-0.733,-0.227,-0.584,0.753,0.28,-0.203],[-0.733,0,-0.203,0.753,0.728,0.178],[-0.733,-0.213,0.178,0.753,0.29,0.94]],"slots":["mount"]},"holosun-aro":{"part":"holosun-aro","model":"holosun-aro.glb","script":"holosun_aro.py","inputs":{"holosun-aro-163-mount.deck_above_rail":0.728,"holosun-aro-163-mount.deck_x":0.01,"holosun-aro.barrel_od":1.2,"holosun-aro.bolt_head_d":0.348,"holosun-aro.bolt_thread_d":0.18,"holosun-aro.bolt_tip_z":0.94,"holosun-aro.button_d":0.357,"holosun-aro.button_mark_length":0.23,"holosun-aro.button_mark_width":0.044,"holosun-aro.button_minus_x":0.068,"holosun-aro.button_plus_x":0.61,"holosun-aro.button_ring_width":0.02,"holosun-aro.cap_d":0.534,"holosun-aro.cap_slot_length":0.24,"holosun-aro.cap_slot_width":0.04,"holosun-aro.clamp_bottom_y":-0.227,"holosun-aro.clamp_corner_chamfer":0.05,"holosun-aro.clamp_flank_end_y":0.02,"holosun-aro.clamp_flank_top_y":0.197,"holosun-aro.clamp_flat_length":0.413,"holosun-aro.clamp_saddle_width":0.144,"holosun-aro.clamp_top_end_y":0.107,"holosun-aro.clamp_top_y":0.28,"holosun-aro.cover_bottom_y":0.927,"holosun-aro.cover_corner_r":0.13,"holosun-aro.cover_front_x":0.8,"holosun-aro.cover_proud":0.035,"holosun-aro.cover_rear_x":-0.52,"holosun-aro.cover_screw_front_x":0.652,"holosun-aro.cover_screw_head_d":0.165,"holosun-aro.cover_screw_rear_x":-0.352,"holosun-aro.cover_screw_y":1.01,"holosun-aro.cover_top_y":1.23,"holosun-aro.cross_bolt_x":0.01,"holosun-aro.cross_bolt_y":0.015,"holosun-aro.deck_foot_width":0.739,"holosun-aro.deck_front_x":0.977,"holosun-aro.deck_top_front_y":2.29,"holosun-aro.deck_top_rear_y":2.376,"holosun-aro.deck_top_width":0.65,"holosun-aro.detail_relief":0.02,"holosun-aro.eyepiece_od":1.094,"holosun-aro.flute_bottom_y":1.875,"holosun-aro.flute_front_x":0.94,"holosun-aro.flute_rear_x":-0.92,"holosun-aro.flute_top_y":2.15,"holosun-aro.housing_front_x":1.055,"holosun-aro.housing_rear_x":-1.028,"holosun-aro.length":2.48,"holosun-aro.logo_height":0.245,"holosun-aro.logo_left_mid_x":0.036,"holosun-aro.logo_length":1.042,"holosun-aro.logo_mid_y":1.64,"holosun-aro.logo_right_mid_x":0.373,"holosun-aro.mount_length":1.486,"holosun-aro.mount_rise":0.728,"holosun-aro.nut_across_flats":0.375,"holosun-aro.nut_outer_z":0.867,"holosun-aro.nut_recess_d":0.48,"holosun-aro.nut_recess_depth":0.08,"holosun-aro.nut_recess_wing_bottom_y":-0.006,"holosun-aro.nut_recess_wing_length":0.829,"holosun-aro.nut_recess_wing_top_y":0.11,"holosun-aro.nut_seat_z":0.641,"holosun-aro.optical_axis_above_rail":1.63,"holosun-aro.pad_front_x":0.89,"holosun-aro.pad_proud":0.012,"holosun-aro.pad_rear_x":-0.23,"holosun-aro.pad_width":0.55,"holosun-aro.rear_behind_clamp_middle":1.115,"holosun-aro.skirt_bottom_front_x":0.806,"holosun-aro.skirt_bottom_rear_x":-0.771,"holosun-aro.skirt_bottom_width":0.894,"holosun-aro.skirt_chamfer_top_y":0.89,"holosun-aro.skirt_shoulder_y":1.3,"holosun-aro.skirt_top_y":1.22,"holosun-aro.skirt_width":1.094,"holosun-aro.stem_end_width":0.136,"holosun-aro.stem_foot_y":0.327,"holosun-aro.stem_length":0.935,"holosun-aro.stem_panel_length":0.475,"holosun-aro.stem_width":0.273,"holosun-aro.top_above_axis":0.78,"holosun-aro.tube_od":1.17,"holosun-aro.turret_x":-0.57,"holosun-aro.windage_boss_d":0.66,"holosun-aro.windage_boss_reach_z":0.73,"holosun-aro.windage_cap_reach_z":0.78,"holosun-aro.windage_y":1.63,"holosun-aro.window":0.866,"holosun-aro.window_d":0.737,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{"side":[[-1.117,2.048],[-1.101,1.339],[-1.012,1.326],[-0.761,0.887],[-0.454,0.882],[-0.457,0.763],[-0.651,0.697],[-0.706,0.648],[-0.702,0.408],[-0.64,0.402],[-0.721,0.355],[-0.72,0.03],[-0.424,0],[0,0],[0.418,0.002],[0.716,0.032],[0.716,0.357],[0.625,0.406],[0.669,0.414],[0.673,0.652],[0.608,0.701],[0.443,0.76],[0.443,0.886],[0.771,0.891],[1.005,1.294],[1.292,1.3],[1.312,1.343],[1.328,1.473],[1.339,1.779],[1.328,2.25],[1.31,2.379],[1.288,2.421],[1.005,2.423],[0.92,2.545],[-0.316,2.613],[-0.523,2.655],[-0.69,2.648],[-0.902,2.604],[-1.01,2.393],[-1.101,2.378]],"front":[[-0.596,1.706],[-0.596,1.566],[-0.544,1.381],[-0.463,1.255],[-0.53,1.196],[-0.53,0.79],[-0.43,0.683],[-0.134,0.661],[-0.116,0.642],[-0.116,0.376],[-0.134,0.358],[-0.415,0.35],[-0.467,0.291],[-0.504,0.291],[-0.559,0.243],[-0.567,-0.141],[-0.544,-0.171],[-0.552,-0.185],[-0.489,-0.241],[-0.349,-0.241],[-0.33,-0.222],[-0.308,-0.06],[-0.29,-0.041],[-0.238,-0.034],[-0.149,-0.034],[-0.112,-0.071],[0.161,-0.071],[0.205,-0.034],[0.294,-0.027],[0.342,-0.052],[0.313,-0.082],[0.305,-0.163],[0.324,-0.182],[0.494,-0.174],[0.53,-0.226],[0.582,-0.204],[0.641,-0.137],[0.819,-0.145],[0.867,-0.097],[0.867,-0.03],[0.9,0.003],[0.922,-0.012],[0.94,0.014],[0.94,0.169],[0.929,0.195],[0.885,0.195],[0.867,0.214],[0.848,0.299],[0.811,0.254],[0.663,0.254],[0.627,0.299],[0.604,0.284],[0.464,0.365],[0.176,0.358],[0.157,0.376],[0.157,0.649],[0.176,0.668],[0.464,0.69],[0.564,0.812],[0.564,0.96],[0.593,0.997],[0.586,1.13],[0.615,1.196],[0.608,1.226],[0.549,1.277],[0.627,1.311],[0.745,1.325],[0.793,1.366],[0.8,1.795],[0.793,1.913],[0.759,1.968],[0.737,1.917],[0.538,1.939],[0.364,2.12],[0.32,2.393],[0.264,2.434],[0.146,2.434],[0.095,2.404],[-0.098,2.404],[-0.12,2.426],[-0.245,2.426],[-0.29,2.419],[-0.33,2.386],[-0.375,2.105],[-0.5,1.965],[-0.574,1.817]]},"features":{"side":{},"front":{}},"placement":{"side":{"plane":"xy","offset":{"y":"clamp_bottom_y"}},"front":{"plane":"zy","offset":{}}},"bounds":{"min":[-1.125,0,-0.6],"max":[1.355,1.682,0.78]},"axis_y":0.902,"volume_in3":3.7793,"centroid":[0.0708,0.8011,0.0134],"shell":[0.0969,0.828,0.0253],"area_in2":17.5359,"triangles":8132,"manifold":true,"slabs":[[-1.129,0,-0.6,-0.063,1.682,0.78],[-0.063,0,-0.6,1.004,1.643,0.602],[1.004,0.302,-0.6,1.359,1.533,0.6]],"slots":["body","lens"]},"holosun-eps-carry.plated":{"part":"holosun-eps-carry","component":"plated","model":"holosun-eps-carry.plated.glb","script":"holosun_eps_carry.py","inputs":{"holosun-eps-carry.adjuster_d":0.176,"holosun-eps-carry.axis_above_base":0.52,"holosun-eps-carry.base_width":0.999,"holosun-eps-carry.button_d":0.312,"holosun-eps-carry.button_front":1.229,"holosun-eps-carry.button_inner_d":0.26,"holosun-eps-carry.button_rear":0.835,"holosun-eps-carry.button_y":0.563,"holosun-eps-carry.counterbore_d":0.23,"holosun-eps-carry.counterbore_depth":0.1,"holosun-eps-carry.deck_y":0.243,"holosun-eps-carry.edge_break":0.008,"holosun-eps-carry.elevation_x":0.26,"holosun-eps-carry.facet_tip_from_rear":0.14,"holosun-eps-carry.feature_relief":0.02,"holosun-eps-carry.glass_inset":0.04,"holosun-eps-carry.glass_thickness":0.03,"holosun-eps-carry.glyph_length":0.195,"holosun-eps-carry.glyph_width":0.026,"holosun-eps-carry.height":0.95,"holosun-eps-carry.hood_width":0.988,"holosun-eps-carry.lip_facet":0.127,"holosun-eps-carry.lip_from_rear":0.187,"holosun-eps-carry.lip_y":0.29,"holosun-eps-carry.pad_bottom":0.373,"holosun-eps-carry.pad_front":1.42,"holosun-eps-carry.pad_proud":0.008,"holosun-eps-carry.pad_rear":0.647,"holosun-eps-carry.pad_top":0.747,"holosun-eps-carry.panel_bottom":0.512,"holosun-eps-carry.panel_front":1.381,"holosun-eps-carry.panel_rear":0.688,"holosun-eps-carry.panel_top":0.701,"holosun-eps-carry.pin_d":0.091,"holosun-eps-carry.pin_from_rear":0.554,"holosun-eps-carry.pin_spacing":0.838,"holosun-eps-carry.plate_corner_r":0.08,"holosun-eps-carry.plate_end_sag":0.03,"holosun-eps-carry.plate_hole_d":0.15,"holosun-eps-carry.plate_hole_in":0.14,"holosun-eps-carry.plate_length":1.7716535433070866,"holosun-eps-carry.plate_middle_x":0.302,"holosun-eps-carry.plate_offset_x":0,"holosun-eps-carry.plate_thickness":0.11811023622047244,"holosun-eps-carry.plate_width":0.984251968503937,"holosun-eps-carry.pocket_d":0.162,"holosun-eps-carry.pocket_depth":0.05,"holosun-eps-carry.pocket_from_rear":1.482,"holosun-eps-carry.pocket_inner_z":0.147,"holosun-eps-carry.pocket_outer_z":0.335,"holosun-eps-carry.rear_x":-0.503,"holosun-eps-carry.screw_hole_d":0.171,"holosun-eps-carry.screw_spacing":0.566,"holosun-eps-carry.top_panel_front":1.386,"holosun-eps-carry.top_panel_rear":1.194,"holosun-eps-carry.top_panel_width":0.53,"holosun-eps-carry.tray_body_top":0.256,"holosun-eps-carry.tray_bottom":0.019,"holosun-eps-carry.tray_front":1.551,"holosun-eps-carry.tray_out":0.062,"holosun-eps-carry.tray_rear":0.858,"holosun-eps-carry.tray_screw_d":0.16,"holosun-eps-carry.tray_screw_x":1.173,"holosun-eps-carry.tray_stem_front":1.32,"holosun-eps-carry.tray_stem_rear":1.02,"holosun-eps-carry.tray_top":0.378,"holosun-eps-carry.windage_x":0.192,"holosun-eps-carry.windage_y":0.165,"holosun-eps-carry.window_arch":0.031,"holosun-eps-carry.window_bezel_height":0.618,"holosun-eps-carry.window_bezel_width":0.806,"holosun-eps-carry.window_centre_y":0.523,"holosun-eps-carry.window_corner_r":0.104,"holosun-eps-carry.window_height":0.58,"holosun-eps-carry.window_width":0.77},"profiles":{"side":[[0,0.238],[0.001,0],[1.597,0],[1.611,0.014],[1.611,0.211],[1.588,0.23],[1.569,0.294],[1.5,0.606],[1.471,0.764],[1.471,0.801],[1.482,0.824],[1.482,0.845],[1.463,0.934],[1.452,0.95],[0.678,0.95],[0.666,0.943],[0.649,0.948],[0.641,0.937],[0.6,0.927],[0.59,0.915],[0.574,0.371],[0.567,0.327],[0.536,0.28],[0.512,0.26],[0.479,0.247],[0.242,0.245],[0.213,0.254],[0.195,0.271],[0.186,0.293],[0.011,0.293],[0.002,0.284]],"front":[[-0.495,0.625],[-0.493,0.461],[-0.487,0.455],[-0.487,0.297],[-0.495,0.202],[-0.492,0],[-0.001,0],[0.492,0],[0.509,0.021],[0.524,0.026],[0.524,0.111],[0.555,0.13],[0.555,0.372],[0.548,0.377],[0.509,0.377],[0.495,0.405],[0.493,0.865],[0.481,0.894],[0.455,0.924],[0.428,0.941],[0.391,0.949],[-0.384,0.949],[-0.416,0.943],[-0.462,0.911],[-0.485,0.869],[-0.487,0.662],[-0.493,0.656]]},"features":{"side":{},"front":{}},"placement":{"side":{"plane":"xy","offset":{"x":"rear_x"}},"front":{"plane":"zy","offset":{}}},"bounds":{"min":[-0.5838,-0.1181,-0.502],"max":[1.1878,0.97,0.559]},"axis_y":0.52,"volume_in3":0.843,"centroid":[0.3828,0.2612,0.0114],"shell":[0.4066,0.2904,0.002],"area_in2":16.5317,"triangles":14468,"manifold":true,"slabs":[[-0.584,-0.118,-0.495,-0.229,0.293,0.5],[-0.229,-0.118,-0.495,0.125,0.934,0.5],[0.125,-0.118,-0.502,1.188,0.97,0.559]],"slots":["body","pad","tray","screws","lens","plate"]},"holosun-eps-carry.sight":{"part":"holosun-eps-carry","component":"sight","model":"holosun-eps-carry.sight.glb","script":"holosun_eps_carry.py","inputs":{"holosun-eps-carry.adjuster_d":0.176,"holosun-eps-carry.axis_above_base":0.52,"holosun-eps-carry.base_width":0.999,"holosun-eps-carry.button_d":0.312,"holosun-eps-carry.button_front":1.229,"holosun-eps-carry.button_inner_d":0.26,"holosun-eps-carry.button_rear":0.835,"holosun-eps-carry.button_y":0.563,"holosun-eps-carry.counterbore_d":0.23,"holosun-eps-carry.counterbore_depth":0.1,"holosun-eps-carry.deck_y":0.243,"holosun-eps-carry.edge_break":0.008,"holosun-eps-carry.elevation_x":0.26,"holosun-eps-carry.facet_tip_from_rear":0.14,"holosun-eps-carry.feature_relief":0.02,"holosun-eps-carry.glass_inset":0.04,"holosun-eps-carry.glass_thickness":0.03,"holosun-eps-carry.glyph_length":0.195,"holosun-eps-carry.glyph_width":0.026,"holosun-eps-carry.height":0.95,"holosun-eps-carry.hood_width":0.988,"holosun-eps-carry.lip_facet":0.127,"holosun-eps-carry.lip_from_rear":0.187,"holosun-eps-carry.lip_y":0.29,"holosun-eps-carry.pad_bottom":0.373,"holosun-eps-carry.pad_front":1.42,"holosun-eps-carry.pad_proud":0.008,"holosun-eps-carry.pad_rear":0.647,"holosun-eps-carry.pad_top":0.747,"holosun-eps-carry.panel_bottom":0.512,"holosun-eps-carry.panel_front":1.381,"holosun-eps-carry.panel_rear":0.688,"holosun-eps-carry.panel_top":0.701,"holosun-eps-carry.pin_d":0.091,"holosun-eps-carry.pin_from_rear":0.554,"holosun-eps-carry.pin_spacing":0.838,"holosun-eps-carry.plate_corner_r":0.08,"holosun-eps-carry.plate_end_sag":0.03,"holosun-eps-carry.plate_hole_d":0.15,"holosun-eps-carry.plate_hole_in":0.14,"holosun-eps-carry.plate_length":1.7716535433070866,"holosun-eps-carry.plate_middle_x":0.302,"holosun-eps-carry.plate_offset_x":0,"holosun-eps-carry.plate_thickness":0.11811023622047244,"holosun-eps-carry.plate_width":0.984251968503937,"holosun-eps-carry.pocket_d":0.162,"holosun-eps-carry.pocket_depth":0.05,"holosun-eps-carry.pocket_from_rear":1.482,"holosun-eps-carry.pocket_inner_z":0.147,"holosun-eps-carry.pocket_outer_z":0.335,"holosun-eps-carry.rear_x":-0.503,"holosun-eps-carry.screw_hole_d":0.171,"holosun-eps-carry.screw_spacing":0.566,"holosun-eps-carry.top_panel_front":1.386,"holosun-eps-carry.top_panel_rear":1.194,"holosun-eps-carry.top_panel_width":0.53,"holosun-eps-carry.tray_body_top":0.256,"holosun-eps-carry.tray_bottom":0.019,"holosun-eps-carry.tray_front":1.551,"holosun-eps-carry.tray_out":0.062,"holosun-eps-carry.tray_rear":0.858,"holosun-eps-carry.tray_screw_d":0.16,"holosun-eps-carry.tray_screw_x":1.173,"holosun-eps-carry.tray_stem_front":1.32,"holosun-eps-carry.tray_stem_rear":1.02,"holosun-eps-carry.tray_top":0.378,"holosun-eps-carry.windage_x":0.192,"holosun-eps-carry.windage_y":0.165,"holosun-eps-carry.window_arch":0.031,"holosun-eps-carry.window_bezel_height":0.618,"holosun-eps-carry.window_bezel_width":0.806,"holosun-eps-carry.window_centre_y":0.523,"holosun-eps-carry.window_corner_r":0.104,"holosun-eps-carry.window_height":0.58,"holosun-eps-carry.window_width":0.77},"profiles":{"side":[[0,0.238],[0.001,0],[1.597,0],[1.611,0.014],[1.611,0.211],[1.588,0.23],[1.569,0.294],[1.5,0.606],[1.471,0.764],[1.471,0.801],[1.482,0.824],[1.482,0.845],[1.463,0.934],[1.452,0.95],[0.678,0.95],[0.666,0.943],[0.649,0.948],[0.641,0.937],[0.6,0.927],[0.59,0.915],[0.574,0.371],[0.567,0.327],[0.536,0.28],[0.512,0.26],[0.479,0.247],[0.242,0.245],[0.213,0.254],[0.195,0.271],[0.186,0.293],[0.011,0.293],[0.002,0.284]],"front":[[-0.495,0.625],[-0.493,0.461],[-0.487,0.455],[-0.487,0.297],[-0.495,0.202],[-0.492,0],[-0.001,0],[0.492,0],[0.509,0.021],[0.524,0.026],[0.524,0.111],[0.555,0.13],[0.555,0.372],[0.548,0.377],[0.509,0.377],[0.495,0.405],[0.493,0.865],[0.481,0.894],[0.455,0.924],[0.428,0.941],[0.391,0.949],[-0.384,0.949],[-0.416,0.943],[-0.462,0.911],[-0.485,0.869],[-0.487,0.662],[-0.493,0.656]]},"features":{"side":{},"front":{}},"placement":{"side":{"plane":"xy","offset":{"x":"rear_x"}},"front":{"plane":"zy","offset":{}}},"bounds":{"min":[-0.503,0,-0.502],"max":[1.108,0.97,0.559]},"axis_y":0.52,"volume_in3":0.6536,"centroid":[0.4037,0.354,0.0147],"shell":[0.4429,0.4089,0.0027],"area_in2":12.3463,"triangles":12924,"manifold":true,"slabs":[[-0.503,0,-0.495,-0.181,0.293,0.5],[-0.181,0,-0.495,0.141,0.942,0.5],[0.141,0,-0.502,1.108,0.97,0.559]],"slots":["body","pad","tray","screws","lens"]},"holosun-hm3x.aside":{"part":"holosun-hm3x","component":"aside","model":"holosun-hm3x.aside.glb","script":"holosun_hm3x.py","inputs":{"holosun-hm3x.adjuster_cap_d":0.63,"holosun-hm3x.adjuster_cap_slot_length":0.22,"holosun-hm3x.adjuster_cap_slot_width":0.06,"holosun-hm3x.axis_to_mount_interface":0.97,"holosun-hm3x.base_left_wall_left_of_centre":0.604,"holosun-hm3x.base_plate_front_behind_hinge_front":0,"holosun-hm3x.base_plate_length":1.73,"holosun-hm3x.base_strip_length":1,"holosun-hm3x.base_strip_right_of_centre":0.045,"holosun-hm3x.base_strip_screw_spacing":0.79,"holosun-hm3x.base_strip_width":0.16,"holosun-hm3x.base_top_above_rail":0.287,"holosun-hm3x.clamp_bolt_behind_hinge_front":0.864,"holosun-hm3x.clamp_bolt_head_d":0.32,"holosun-hm3x.clamp_nose_width":0.445,"holosun-hm3x.detail_relief":0.02,"holosun-hm3x.eyepiece_glass_d":0.912,"holosun-hm3x.eyepiece_ring_flute_end_inset":0.03,"holosun-hm3x.eyepiece_ring_flute_width":14.8,"holosun-hm3x.eyepiece_ring_flutes":14,"holosun-hm3x.eyepiece_ring_length":0.405,"holosun-hm3x.eyepiece_ring_od":1.42,"holosun-hm3x.flip_angle":90,"holosun-hm3x.flip_plate_length":1,"holosun-hm3x.flip_plate_screw_d":0.16,"holosun-hm3x.flip_plate_screw_spacing":0.69,"holosun-hm3x.flip_plate_width":0.58,"holosun-hm3x.foot_rib_bottom_above_interface":0.104,"holosun-hm3x.foot_rib_count":5,"holosun-hm3x.foot_rib_first_front_ahead_of_base_centre":0.438,"holosun-hm3x.foot_rib_lean":30,"holosun-hm3x.foot_rib_pitch":0.198,"holosun-hm3x.foot_rib_rear_wall_behind_base_centre":0.359,"holosun-hm3x.foot_rib_top_above_interface":0.31,"holosun-hm3x.foot_rib_top_fall":4.7,"holosun-hm3x.foot_rib_width":0.128,"holosun-hm3x.hinge_axis_above_rail":0.44,"holosun-hm3x.hinge_axis_right_of_centre":0.47,"holosun-hm3x.hinge_barrel_d":0.35,"holosun-hm3x.hinge_block_length":1.728,"holosun-hm3x.hinge_cap_proud":0.16,"holosun-hm3x.hinge_knuckle_inner_right_of_centre":0.215,"holosun-hm3x.hinge_knuckle_length":0.35,"holosun-hm3x.hinge_seat_above_rail":0.21,"holosun-hm3x.lever_arm_thickness":0.09,"holosun-hm3x.lever_bottom_below_rail":0.163,"holosun-hm3x.lever_catch_length":0.36,"holosun-hm3x.lever_catch_proud":0.085,"holosun-hm3x.lever_ear_d":0.19,"holosun-hm3x.lever_link_ahead_of_centre":0.38,"holosun-hm3x.lever_link_height":0.332,"holosun-hm3x.lever_link_width":0.093,"holosun-hm3x.lever_pad_length":0.206,"holosun-hm3x.lever_pivot_ahead_of_centre":0.097,"holosun-hm3x.lever_rear_behind_centre":0.91,"holosun-hm3x.lever_recess_behind_centre":0.507,"holosun-hm3x.lever_recess_height":0.173,"holosun-hm3x.lever_recess_length":0.32,"holosun-hm3x.lever_roller_bottom_below_rail":0.036,"holosun-hm3x.lever_roller_d":0.206,"holosun-hm3x.lever_roller_top_above_rail":0.073,"holosun-hm3x.lever_screw_behind_centre":0.545,"holosun-hm3x.lever_screw_d":0.15,"holosun-hm3x.lever_tip_outer_from_wall":0.18,"holosun-hm3x.lever_top_above_rail":0.203,"holosun-hm3x.logo_oval_behind_top_cap":0.02,"holosun-hm3x.logo_oval_face_left_of_axis":0.739,"holosun-hm3x.logo_oval_height":0.31,"holosun-hm3x.logo_oval_length":1.239,"holosun-hm3x.logo_oval_rim":0.02,"holosun-hm3x.mount_base_length":1.93,"holosun-hm3x.objective_glass_d":0.906,"holosun-hm3x.objective_ring_flute_depth":0.0103,"holosun-hm3x.objective_ring_flute_floor":8.5,"holosun-hm3x.objective_ring_flute_wall":2.75,"holosun-hm3x.objective_ring_flutes":16,"holosun-hm3x.objective_ring_length":0.348,"holosun-hm3x.objective_ring_od":1.32,"holosun-hm3x.optical_axis_above_rail_no_spacer":1.41,"holosun-hm3x.optical_axis_above_rail_spacer":1.63,"holosun-hm3x.right_logo_oval_behind_side_cap":1.12,"holosun-hm3x.right_logo_oval_height":0.245,"holosun-hm3x.right_logo_oval_length":1,"holosun-hm3x.side_cap_ahead_of_top_cap":0.01,"holosun-hm3x.side_cap_face_right_of_axis":0.786,"holosun-hm3x.spacer_thickness":0.22,"holosun-hm3x.tension_screw_slot_width":0.064,"holosun-hm3x.tool_knob_above_rail":0.17,"holosun-hm3x.tool_knob_d":0.3,"holosun-hm3x.tool_knob_length":0.208,"holosun-hm3x.tool_knob_right_of_centre":0.42,"holosun-hm3x.top_above_rail_no_spacer":2.2,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{"side":[[-2.995,0.748],[-2.978,0.75],[-2.946,0.713],[-2.633,0.713],[-2.602,0.734],[-2.598,0.785],[-2.577,0.806],[-2.455,0.806],[-2.434,0.785],[-2.434,0.715],[-2.418,0.699],[-1.89,0.708],[-0.797,0.675],[-0.762,0.649],[-0.762,0.332],[-0.783,0.311],[-0.946,0.311],[-0.958,0.294],[-0.963,-0.005],[-0.923,0.002],[-0.902,-0.019],[-0.897,-0.126],[-0.867,-0.161],[-0.815,-0.175],[-0.708,-0.17],[-0.652,-0.222],[0.894,-0.222],[0.878,-0.201],[0.913,-0.166],[0.941,-0.138],[0.962,-0.154],[0.967,0.701],[0.955,0.712],[0.633,0.712],[0.612,0.738],[0.642,0.773],[0.694,0.773],[0.712,0.759],[1.021,0.768],[1.049,0.74],[1.065,0.752],[1.042,0.78],[1.046,2.037],[1.065,2.074],[1.053,2.086],[1.025,2.058],[0.712,2.067],[0.694,2.053],[0.642,2.053],[-0.002,2.128],[-0.016,2.142],[-0.096,2.147],[-0.131,2.186],[-0.119,2.203],[-0.727,2.203],[-0.759,2.198],[-0.801,2.156],[-0.881,2.151],[-0.895,2.137],[-1.736,2.109],[-2.189,2.109],[-2.207,2.123],[-2.436,2.128],[-2.434,2.042],[-2.455,2.021],[-2.576,2.021],[-2.597,2.042],[-2.597,2.084],[-2.633,2.114],[-2.946,2.109],[-2.99,2.06]],"front":[[-0.873,0.001],[-0.855,-0.027],[-0.869,-0.041],[-0.873,-0.139],[-0.82,-0.132],[-0.787,-0.17],[-0.731,-0.174],[-0.675,-0.221],[-0.358,-0.207],[-0.327,-0.167],[-0.388,-0.093],[-0.306,0.003],[0.347,0.003],[0.442,-0.088],[0.363,-0.177],[0.363,-0.214],[0.561,-0.221],[0.596,-0.186],[0.596,0.192],[0.657,0.374],[0.652,0.63],[0.608,0.689],[0.57,0.707],[0.319,0.712],[0.298,0.733],[0.505,0.875],[0.673,1.099],[0.787,1.092],[0.783,1.722],[0.673,1.724],[0.522,1.927],[0.312,2.086],[0.312,2.188],[0.295,2.2],[-0.302,2.2],[-0.313,2.188],[-0.313,2.086],[-0.484,1.967],[-0.556,1.894],[-0.687,1.703],[-0.729,1.582],[-0.719,1.549],[-0.738,1.493],[-0.738,1.405],[-0.752,1.391],[-0.738,1.377],[-0.715,1.195],[-0.687,1.12],[-0.561,0.933],[-0.456,0.833],[-0.295,0.728],[-0.295,0.458],[-0.313,0.439],[-0.295,0.42],[-0.281,0.346],[-0.239,0.308],[-0.26,0.287],[-0.563,0.287],[-0.619,0.231],[-0.675,0.236],[-0.703,0.213],[-0.782,0.208],[-0.82,0.171],[-0.862,0.171],[-0.859,0.052]]},"features":{"side":{},"front":{}},"placement":{"side":{"plane":"xy","offset":{}},"front":{"plane":"zy","offset":{}}},"bounds":{"min":[-2.995,-0.221,-0.873],"max":[1.046,1.649,2.45]},"axis_y":0.91,"axis_z":1.66,"volume_in3":7.6348,"centroid":[-0.7934,0.8065,1.3954],"shell":[-0.5791,0.6665,1.0202],"area_in2":42.4426,"triangles":21362,"manifold":true,"rail_seat":{"x":[-0.765,0.965],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-2.999,0.176,0.942,-1.159,1.628,2.378],[-1.159,-0.163,-0.794,-0.79,1.649,2.413],[-0.79,-0.221,-0.853,-0.054,1.649,2.45],[-0.054,-0.221,-0.873,0.314,1.649,2.397],[0.314,-0.221,-0.634,1.05,1.591,2.341]],"slots":["body","mount","hardware","lens"]},"holosun-hm3x.aside_no_spacer":{"part":"holosun-hm3x","component":"aside_no_spacer","model":"holosun-hm3x.aside_no_spacer.glb","script":"holosun_hm3x.py","inputs":{"holosun-hm3x.adjuster_cap_d":0.63,"holosun-hm3x.adjuster_cap_slot_length":0.22,"holosun-hm3x.adjuster_cap_slot_width":0.06,"holosun-hm3x.axis_to_mount_interface":0.97,"holosun-hm3x.base_left_wall_left_of_centre":0.604,"holosun-hm3x.base_plate_front_behind_hinge_front":0,"holosun-hm3x.base_plate_length":1.73,"holosun-hm3x.base_strip_length":1,"holosun-hm3x.base_strip_right_of_centre":0.045,"holosun-hm3x.base_strip_screw_spacing":0.79,"holosun-hm3x.base_strip_width":0.16,"holosun-hm3x.base_top_above_rail":0.287,"holosun-hm3x.clamp_bolt_behind_hinge_front":0.864,"holosun-hm3x.clamp_bolt_head_d":0.32,"holosun-hm3x.clamp_nose_width":0.445,"holosun-hm3x.detail_relief":0.02,"holosun-hm3x.eyepiece_glass_d":0.912,"holosun-hm3x.eyepiece_ring_flute_end_inset":0.03,"holosun-hm3x.eyepiece_ring_flute_width":14.8,"holosun-hm3x.eyepiece_ring_flutes":14,"holosun-hm3x.eyepiece_ring_length":0.405,"holosun-hm3x.eyepiece_ring_od":1.42,"holosun-hm3x.flip_angle":90,"holosun-hm3x.flip_plate_length":1,"holosun-hm3x.flip_plate_screw_d":0.16,"holosun-hm3x.flip_plate_screw_spacing":0.69,"holosun-hm3x.flip_plate_width":0.58,"holosun-hm3x.foot_rib_bottom_above_interface":0.104,"holosun-hm3x.foot_rib_count":5,"holosun-hm3x.foot_rib_first_front_ahead_of_base_centre":0.438,"holosun-hm3x.foot_rib_lean":30,"holosun-hm3x.foot_rib_pitch":0.198,"holosun-hm3x.foot_rib_rear_wall_behind_base_centre":0.359,"holosun-hm3x.foot_rib_top_above_interface":0.31,"holosun-hm3x.foot_rib_top_fall":4.7,"holosun-hm3x.foot_rib_width":0.128,"holosun-hm3x.hinge_axis_above_rail":0.44,"holosun-hm3x.hinge_axis_right_of_centre":0.47,"holosun-hm3x.hinge_barrel_d":0.35,"holosun-hm3x.hinge_block_length":1.728,"holosun-hm3x.hinge_cap_proud":0.16,"holosun-hm3x.hinge_knuckle_inner_right_of_centre":0.215,"holosun-hm3x.hinge_knuckle_length":0.35,"holosun-hm3x.hinge_seat_above_rail":0.21,"holosun-hm3x.lever_arm_thickness":0.09,"holosun-hm3x.lever_bottom_below_rail":0.163,"holosun-hm3x.lever_catch_length":0.36,"holosun-hm3x.lever_catch_proud":0.085,"holosun-hm3x.lever_ear_d":0.19,"holosun-hm3x.lever_link_ahead_of_centre":0.38,"holosun-hm3x.lever_link_height":0.332,"holosun-hm3x.lever_link_width":0.093,"holosun-hm3x.lever_pad_length":0.206,"holosun-hm3x.lever_pivot_ahead_of_centre":0.097,"holosun-hm3x.lever_rear_behind_centre":0.91,"holosun-hm3x.lever_recess_behind_centre":0.507,"holosun-hm3x.lever_recess_height":0.173,"holosun-hm3x.lever_recess_length":0.32,"holosun-hm3x.lever_roller_bottom_below_rail":0.036,"holosun-hm3x.lever_roller_d":0.206,"holosun-hm3x.lever_roller_top_above_rail":0.073,"holosun-hm3x.lever_screw_behind_centre":0.545,"holosun-hm3x.lever_screw_d":0.15,"holosun-hm3x.lever_tip_outer_from_wall":0.18,"holosun-hm3x.lever_top_above_rail":0.203,"holosun-hm3x.logo_oval_behind_top_cap":0.02,"holosun-hm3x.logo_oval_face_left_of_axis":0.739,"holosun-hm3x.logo_oval_height":0.31,"holosun-hm3x.logo_oval_length":1.239,"holosun-hm3x.logo_oval_rim":0.02,"holosun-hm3x.mount_base_length":1.93,"holosun-hm3x.objective_glass_d":0.906,"holosun-hm3x.objective_ring_flute_depth":0.0103,"holosun-hm3x.objective_ring_flute_floor":8.5,"holosun-hm3x.objective_ring_flute_wall":2.75,"holosun-hm3x.objective_ring_flutes":16,"holosun-hm3x.objective_ring_length":0.348,"holosun-hm3x.objective_ring_od":1.32,"holosun-hm3x.optical_axis_above_rail_no_spacer":1.41,"holosun-hm3x.optical_axis_above_rail_spacer":1.63,"holosun-hm3x.right_logo_oval_behind_side_cap":1.12,"holosun-hm3x.right_logo_oval_height":0.245,"holosun-hm3x.right_logo_oval_length":1,"holosun-hm3x.side_cap_ahead_of_top_cap":0.01,"holosun-hm3x.side_cap_face_right_of_axis":0.786,"holosun-hm3x.spacer_thickness":0.22,"holosun-hm3x.tension_screw_slot_width":0.064,"holosun-hm3x.tool_knob_above_rail":0.17,"holosun-hm3x.tool_knob_d":0.3,"holosun-hm3x.tool_knob_length":0.208,"holosun-hm3x.tool_knob_right_of_centre":0.42,"holosun-hm3x.top_above_rail_no_spacer":2.2,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{"side":[[-2.995,0.748],[-2.978,0.75],[-2.946,0.713],[-2.633,0.713],[-2.602,0.734],[-2.598,0.785],[-2.577,0.806],[-2.455,0.806],[-2.434,0.785],[-2.434,0.715],[-2.418,0.699],[-1.89,0.708],[-0.797,0.675],[-0.762,0.649],[-0.762,0.332],[-0.783,0.311],[-0.946,0.311],[-0.958,0.294],[-0.963,-0.005],[-0.923,0.002],[-0.902,-0.019],[-0.897,-0.126],[-0.867,-0.161],[-0.815,-0.175],[-0.708,-0.17],[-0.652,-0.222],[0.894,-0.222],[0.878,-0.201],[0.913,-0.166],[0.941,-0.138],[0.962,-0.154],[0.967,0.701],[0.955,0.712],[0.633,0.712],[0.612,0.738],[0.642,0.773],[0.694,0.773],[0.712,0.759],[1.021,0.768],[1.049,0.74],[1.065,0.752],[1.042,0.78],[1.046,2.037],[1.065,2.074],[1.053,2.086],[1.025,2.058],[0.712,2.067],[0.694,2.053],[0.642,2.053],[-0.002,2.128],[-0.016,2.142],[-0.096,2.147],[-0.131,2.186],[-0.119,2.203],[-0.727,2.203],[-0.759,2.198],[-0.801,2.156],[-0.881,2.151],[-0.895,2.137],[-1.736,2.109],[-2.189,2.109],[-2.207,2.123],[-2.436,2.128],[-2.434,2.042],[-2.455,2.021],[-2.576,2.021],[-2.597,2.042],[-2.597,2.084],[-2.633,2.114],[-2.946,2.109],[-2.99,2.06]],"front":[[-0.873,0.001],[-0.855,-0.027],[-0.869,-0.041],[-0.873,-0.139],[-0.82,-0.132],[-0.787,-0.17],[-0.731,-0.174],[-0.675,-0.221],[-0.358,-0.207],[-0.327,-0.167],[-0.388,-0.093],[-0.306,0.003],[0.347,0.003],[0.442,-0.088],[0.363,-0.177],[0.363,-0.214],[0.561,-0.221],[0.596,-0.186],[0.596,0.192],[0.657,0.374],[0.652,0.63],[0.608,0.689],[0.57,0.707],[0.319,0.712],[0.298,0.733],[0.505,0.875],[0.673,1.099],[0.787,1.092],[0.783,1.722],[0.673,1.724],[0.522,1.927],[0.312,2.086],[0.312,2.188],[0.295,2.2],[-0.302,2.2],[-0.313,2.188],[-0.313,2.086],[-0.484,1.967],[-0.556,1.894],[-0.687,1.703],[-0.729,1.582],[-0.719,1.549],[-0.738,1.493],[-0.738,1.405],[-0.752,1.391],[-0.738,1.377],[-0.715,1.195],[-0.687,1.12],[-0.561,0.933],[-0.456,0.833],[-0.295,0.728],[-0.295,0.458],[-0.313,0.439],[-0.295,0.42],[-0.281,0.346],[-0.239,0.308],[-0.26,0.287],[-0.563,0.287],[-0.619,0.231],[-0.675,0.236],[-0.703,0.213],[-0.782,0.208],[-0.82,0.171],[-0.862,0.171],[-0.859,0.052]]},"features":{"side":{},"front":{}},"placement":{"side":{"plane":"xy","offset":{}},"front":{"plane":"zy","offset":{}}},"bounds":{"min":[-2.995,-0.221,-0.873],"max":[1.046,1.649,2.23]},"axis_y":0.91,"axis_z":1.44,"volume_in3":7.5176,"centroid":[-0.8074,0.8049,1.2212],"shell":[-0.6083,0.656,0.9006],"area_in2":40.6955,"triangles":21350,"manifold":true,"rail_seat":{"x":[-0.765,0.965],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-2.999,0.176,0.722,-1.159,1.628,2.158],[-1.159,-0.163,-0.794,-0.79,1.649,2.193],[-0.79,-0.221,-0.853,-0.054,1.649,2.23],[-0.054,-0.221,-0.873,0.314,1.649,2.177],[0.314,-0.221,-0.634,1.05,1.591,2.121]],"slots":["body","mount","hardware","lens"]},"holosun-hm3x.inline":{"part":"holosun-hm3x","component":"inline","model":"holosun-hm3x.inline.glb","script":"holosun_hm3x.py","inputs":{"holosun-hm3x.adjuster_cap_d":0.63,"holosun-hm3x.adjuster_cap_slot_length":0.22,"holosun-hm3x.adjuster_cap_slot_width":0.06,"holosun-hm3x.axis_to_mount_interface":0.97,"holosun-hm3x.base_left_wall_left_of_centre":0.604,"holosun-hm3x.base_plate_front_behind_hinge_front":0,"holosun-hm3x.base_plate_length":1.73,"holosun-hm3x.base_strip_length":1,"holosun-hm3x.base_strip_right_of_centre":0.045,"holosun-hm3x.base_strip_screw_spacing":0.79,"holosun-hm3x.base_strip_width":0.16,"holosun-hm3x.base_top_above_rail":0.287,"holosun-hm3x.clamp_bolt_behind_hinge_front":0.864,"holosun-hm3x.clamp_bolt_head_d":0.32,"holosun-hm3x.clamp_nose_width":0.445,"holosun-hm3x.detail_relief":0.02,"holosun-hm3x.eyepiece_glass_d":0.912,"holosun-hm3x.eyepiece_ring_flute_end_inset":0.03,"holosun-hm3x.eyepiece_ring_flute_width":14.8,"holosun-hm3x.eyepiece_ring_flutes":14,"holosun-hm3x.eyepiece_ring_length":0.405,"holosun-hm3x.eyepiece_ring_od":1.42,"holosun-hm3x.flip_angle":90,"holosun-hm3x.flip_plate_length":1,"holosun-hm3x.flip_plate_screw_d":0.16,"holosun-hm3x.flip_plate_screw_spacing":0.69,"holosun-hm3x.flip_plate_width":0.58,"holosun-hm3x.foot_rib_bottom_above_interface":0.104,"holosun-hm3x.foot_rib_count":5,"holosun-hm3x.foot_rib_first_front_ahead_of_base_centre":0.438,"holosun-hm3x.foot_rib_lean":30,"holosun-hm3x.foot_rib_pitch":0.198,"holosun-hm3x.foot_rib_rear_wall_behind_base_centre":0.359,"holosun-hm3x.foot_rib_top_above_interface":0.31,"holosun-hm3x.foot_rib_top_fall":4.7,"holosun-hm3x.foot_rib_width":0.128,"holosun-hm3x.hinge_axis_above_rail":0.44,"holosun-hm3x.hinge_axis_right_of_centre":0.47,"holosun-hm3x.hinge_barrel_d":0.35,"holosun-hm3x.hinge_block_length":1.728,"holosun-hm3x.hinge_cap_proud":0.16,"holosun-hm3x.hinge_knuckle_inner_right_of_centre":0.215,"holosun-hm3x.hinge_knuckle_length":0.35,"holosun-hm3x.hinge_seat_above_rail":0.21,"holosun-hm3x.lever_arm_thickness":0.09,"holosun-hm3x.lever_bottom_below_rail":0.163,"holosun-hm3x.lever_catch_length":0.36,"holosun-hm3x.lever_catch_proud":0.085,"holosun-hm3x.lever_ear_d":0.19,"holosun-hm3x.lever_link_ahead_of_centre":0.38,"holosun-hm3x.lever_link_height":0.332,"holosun-hm3x.lever_link_width":0.093,"holosun-hm3x.lever_pad_length":0.206,"holosun-hm3x.lever_pivot_ahead_of_centre":0.097,"holosun-hm3x.lever_rear_behind_centre":0.91,"holosun-hm3x.lever_recess_behind_centre":0.507,"holosun-hm3x.lever_recess_height":0.173,"holosun-hm3x.lever_recess_length":0.32,"holosun-hm3x.lever_roller_bottom_below_rail":0.036,"holosun-hm3x.lever_roller_d":0.206,"holosun-hm3x.lever_roller_top_above_rail":0.073,"holosun-hm3x.lever_screw_behind_centre":0.545,"holosun-hm3x.lever_screw_d":0.15,"holosun-hm3x.lever_tip_outer_from_wall":0.18,"holosun-hm3x.lever_top_above_rail":0.203,"holosun-hm3x.logo_oval_behind_top_cap":0.02,"holosun-hm3x.logo_oval_face_left_of_axis":0.739,"holosun-hm3x.logo_oval_height":0.31,"holosun-hm3x.logo_oval_length":1.239,"holosun-hm3x.logo_oval_rim":0.02,"holosun-hm3x.mount_base_length":1.93,"holosun-hm3x.objective_glass_d":0.906,"holosun-hm3x.objective_ring_flute_depth":0.0103,"holosun-hm3x.objective_ring_flute_floor":8.5,"holosun-hm3x.objective_ring_flute_wall":2.75,"holosun-hm3x.objective_ring_flutes":16,"holosun-hm3x.objective_ring_length":0.348,"holosun-hm3x.objective_ring_od":1.32,"holosun-hm3x.optical_axis_above_rail_no_spacer":1.41,"holosun-hm3x.optical_axis_above_rail_spacer":1.63,"holosun-hm3x.right_logo_oval_behind_side_cap":1.12,"holosun-hm3x.right_logo_oval_height":0.245,"holosun-hm3x.right_logo_oval_length":1,"holosun-hm3x.side_cap_ahead_of_top_cap":0.01,"holosun-hm3x.side_cap_face_right_of_axis":0.786,"holosun-hm3x.spacer_thickness":0.22,"holosun-hm3x.tension_screw_slot_width":0.064,"holosun-hm3x.tool_knob_above_rail":0.17,"holosun-hm3x.tool_knob_d":0.3,"holosun-hm3x.tool_knob_length":0.208,"holosun-hm3x.tool_knob_right_of_centre":0.42,"holosun-hm3x.top_above_rail_no_spacer":2.2,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{"side":[[-2.995,0.748],[-2.978,0.75],[-2.946,0.713],[-2.633,0.713],[-2.602,0.734],[-2.598,0.785],[-2.577,0.806],[-2.455,0.806],[-2.434,0.785],[-2.434,0.715],[-2.418,0.699],[-1.89,0.708],[-0.797,0.675],[-0.762,0.649],[-0.762,0.332],[-0.783,0.311],[-0.946,0.311],[-0.958,0.294],[-0.963,-0.005],[-0.923,0.002],[-0.902,-0.019],[-0.897,-0.126],[-0.867,-0.161],[-0.815,-0.175],[-0.708,-0.17],[-0.652,-0.222],[0.894,-0.222],[0.878,-0.201],[0.913,-0.166],[0.941,-0.138],[0.962,-0.154],[0.967,0.701],[0.955,0.712],[0.633,0.712],[0.612,0.738],[0.642,0.773],[0.694,0.773],[0.712,0.759],[1.021,0.768],[1.049,0.74],[1.065,0.752],[1.042,0.78],[1.046,2.037],[1.065,2.074],[1.053,2.086],[1.025,2.058],[0.712,2.067],[0.694,2.053],[0.642,2.053],[-0.002,2.128],[-0.016,2.142],[-0.096,2.147],[-0.131,2.186],[-0.119,2.203],[-0.727,2.203],[-0.759,2.198],[-0.801,2.156],[-0.881,2.151],[-0.895,2.137],[-1.736,2.109],[-2.189,2.109],[-2.207,2.123],[-2.436,2.128],[-2.434,2.042],[-2.455,2.021],[-2.576,2.021],[-2.597,2.042],[-2.597,2.084],[-2.633,2.114],[-2.946,2.109],[-2.99,2.06]],"front":[[-0.873,0.001],[-0.855,-0.027],[-0.869,-0.041],[-0.873,-0.139],[-0.82,-0.132],[-0.787,-0.17],[-0.731,-0.174],[-0.675,-0.221],[-0.358,-0.207],[-0.327,-0.167],[-0.388,-0.093],[-0.306,0.003],[0.347,0.003],[0.442,-0.088],[0.363,-0.177],[0.363,-0.214],[0.561,-0.221],[0.596,-0.186],[0.596,0.192],[0.657,0.374],[0.652,0.63],[0.608,0.689],[0.57,0.707],[0.319,0.712],[0.298,0.733],[0.505,0.875],[0.673,1.099],[0.787,1.092],[0.783,1.722],[0.673,1.724],[0.522,1.927],[0.312,2.086],[0.312,2.188],[0.295,2.2],[-0.302,2.2],[-0.313,2.188],[-0.313,2.086],[-0.484,1.967],[-0.556,1.894],[-0.687,1.703],[-0.729,1.582],[-0.719,1.549],[-0.738,1.493],[-0.738,1.405],[-0.752,1.391],[-0.738,1.377],[-0.715,1.195],[-0.687,1.12],[-0.561,0.933],[-0.456,0.833],[-0.295,0.728],[-0.295,0.458],[-0.313,0.439],[-0.295,0.42],[-0.281,0.346],[-0.239,0.308],[-0.26,0.287],[-0.563,0.287],[-0.619,0.231],[-0.675,0.236],[-0.703,0.213],[-0.782,0.208],[-0.82,0.171],[-0.862,0.171],[-0.859,0.052]]},"features":{"side":{},"front":{}},"placement":{"side":{"plane":"xy","offset":{}},"front":{"plane":"zy","offset":{}}},"bounds":{"min":[-2.995,-0.221,-0.873],"max":[1.046,2.42,0.786]},"axis_y":1.63,"axis_z":0,"volume_in3":7.6348,"centroid":[-0.7934,1.3852,0.0102],"shell":[-0.5791,1.0485,0.0037],"area_in2":42.4426,"triangles":21362,"manifold":true,"rail_seat":{"x":[-0.765,0.965],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-2.999,0.912,-0.718,-1.159,2.348,0.734],[-1.159,-0.163,-0.794,-0.79,2.383,0.734],[-0.79,-0.221,-0.853,-0.054,2.42,0.786],[-0.054,-0.221,-0.873,0.314,2.367,0.718],[0.314,-0.221,-0.681,1.05,2.311,0.681]],"slots":["body","mount","hardware","lens"]},"holosun-hm3x.inline_no_spacer":{"part":"holosun-hm3x","component":"inline_no_spacer","model":"holosun-hm3x.inline_no_spacer.glb","script":"holosun_hm3x.py","inputs":{"holosun-hm3x.adjuster_cap_d":0.63,"holosun-hm3x.adjuster_cap_slot_length":0.22,"holosun-hm3x.adjuster_cap_slot_width":0.06,"holosun-hm3x.axis_to_mount_interface":0.97,"holosun-hm3x.base_left_wall_left_of_centre":0.604,"holosun-hm3x.base_plate_front_behind_hinge_front":0,"holosun-hm3x.base_plate_length":1.73,"holosun-hm3x.base_strip_length":1,"holosun-hm3x.base_strip_right_of_centre":0.045,"holosun-hm3x.base_strip_screw_spacing":0.79,"holosun-hm3x.base_strip_width":0.16,"holosun-hm3x.base_top_above_rail":0.287,"holosun-hm3x.clamp_bolt_behind_hinge_front":0.864,"holosun-hm3x.clamp_bolt_head_d":0.32,"holosun-hm3x.clamp_nose_width":0.445,"holosun-hm3x.detail_relief":0.02,"holosun-hm3x.eyepiece_glass_d":0.912,"holosun-hm3x.eyepiece_ring_flute_end_inset":0.03,"holosun-hm3x.eyepiece_ring_flute_width":14.8,"holosun-hm3x.eyepiece_ring_flutes":14,"holosun-hm3x.eyepiece_ring_length":0.405,"holosun-hm3x.eyepiece_ring_od":1.42,"holosun-hm3x.flip_angle":90,"holosun-hm3x.flip_plate_length":1,"holosun-hm3x.flip_plate_screw_d":0.16,"holosun-hm3x.flip_plate_screw_spacing":0.69,"holosun-hm3x.flip_plate_width":0.58,"holosun-hm3x.foot_rib_bottom_above_interface":0.104,"holosun-hm3x.foot_rib_count":5,"holosun-hm3x.foot_rib_first_front_ahead_of_base_centre":0.438,"holosun-hm3x.foot_rib_lean":30,"holosun-hm3x.foot_rib_pitch":0.198,"holosun-hm3x.foot_rib_rear_wall_behind_base_centre":0.359,"holosun-hm3x.foot_rib_top_above_interface":0.31,"holosun-hm3x.foot_rib_top_fall":4.7,"holosun-hm3x.foot_rib_width":0.128,"holosun-hm3x.hinge_axis_above_rail":0.44,"holosun-hm3x.hinge_axis_right_of_centre":0.47,"holosun-hm3x.hinge_barrel_d":0.35,"holosun-hm3x.hinge_block_length":1.728,"holosun-hm3x.hinge_cap_proud":0.16,"holosun-hm3x.hinge_knuckle_inner_right_of_centre":0.215,"holosun-hm3x.hinge_knuckle_length":0.35,"holosun-hm3x.hinge_seat_above_rail":0.21,"holosun-hm3x.lever_arm_thickness":0.09,"holosun-hm3x.lever_bottom_below_rail":0.163,"holosun-hm3x.lever_catch_length":0.36,"holosun-hm3x.lever_catch_proud":0.085,"holosun-hm3x.lever_ear_d":0.19,"holosun-hm3x.lever_link_ahead_of_centre":0.38,"holosun-hm3x.lever_link_height":0.332,"holosun-hm3x.lever_link_width":0.093,"holosun-hm3x.lever_pad_length":0.206,"holosun-hm3x.lever_pivot_ahead_of_centre":0.097,"holosun-hm3x.lever_rear_behind_centre":0.91,"holosun-hm3x.lever_recess_behind_centre":0.507,"holosun-hm3x.lever_recess_height":0.173,"holosun-hm3x.lever_recess_length":0.32,"holosun-hm3x.lever_roller_bottom_below_rail":0.036,"holosun-hm3x.lever_roller_d":0.206,"holosun-hm3x.lever_roller_top_above_rail":0.073,"holosun-hm3x.lever_screw_behind_centre":0.545,"holosun-hm3x.lever_screw_d":0.15,"holosun-hm3x.lever_tip_outer_from_wall":0.18,"holosun-hm3x.lever_top_above_rail":0.203,"holosun-hm3x.logo_oval_behind_top_cap":0.02,"holosun-hm3x.logo_oval_face_left_of_axis":0.739,"holosun-hm3x.logo_oval_height":0.31,"holosun-hm3x.logo_oval_length":1.239,"holosun-hm3x.logo_oval_rim":0.02,"holosun-hm3x.mount_base_length":1.93,"holosun-hm3x.objective_glass_d":0.906,"holosun-hm3x.objective_ring_flute_depth":0.0103,"holosun-hm3x.objective_ring_flute_floor":8.5,"holosun-hm3x.objective_ring_flute_wall":2.75,"holosun-hm3x.objective_ring_flutes":16,"holosun-hm3x.objective_ring_length":0.348,"holosun-hm3x.objective_ring_od":1.32,"holosun-hm3x.optical_axis_above_rail_no_spacer":1.41,"holosun-hm3x.optical_axis_above_rail_spacer":1.63,"holosun-hm3x.right_logo_oval_behind_side_cap":1.12,"holosun-hm3x.right_logo_oval_height":0.245,"holosun-hm3x.right_logo_oval_length":1,"holosun-hm3x.side_cap_ahead_of_top_cap":0.01,"holosun-hm3x.side_cap_face_right_of_axis":0.786,"holosun-hm3x.spacer_thickness":0.22,"holosun-hm3x.tension_screw_slot_width":0.064,"holosun-hm3x.tool_knob_above_rail":0.17,"holosun-hm3x.tool_knob_d":0.3,"holosun-hm3x.tool_knob_length":0.208,"holosun-hm3x.tool_knob_right_of_centre":0.42,"holosun-hm3x.top_above_rail_no_spacer":2.2,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{"side":[[-2.995,0.748],[-2.978,0.75],[-2.946,0.713],[-2.633,0.713],[-2.602,0.734],[-2.598,0.785],[-2.577,0.806],[-2.455,0.806],[-2.434,0.785],[-2.434,0.715],[-2.418,0.699],[-1.89,0.708],[-0.797,0.675],[-0.762,0.649],[-0.762,0.332],[-0.783,0.311],[-0.946,0.311],[-0.958,0.294],[-0.963,-0.005],[-0.923,0.002],[-0.902,-0.019],[-0.897,-0.126],[-0.867,-0.161],[-0.815,-0.175],[-0.708,-0.17],[-0.652,-0.222],[0.894,-0.222],[0.878,-0.201],[0.913,-0.166],[0.941,-0.138],[0.962,-0.154],[0.967,0.701],[0.955,0.712],[0.633,0.712],[0.612,0.738],[0.642,0.773],[0.694,0.773],[0.712,0.759],[1.021,0.768],[1.049,0.74],[1.065,0.752],[1.042,0.78],[1.046,2.037],[1.065,2.074],[1.053,2.086],[1.025,2.058],[0.712,2.067],[0.694,2.053],[0.642,2.053],[-0.002,2.128],[-0.016,2.142],[-0.096,2.147],[-0.131,2.186],[-0.119,2.203],[-0.727,2.203],[-0.759,2.198],[-0.801,2.156],[-0.881,2.151],[-0.895,2.137],[-1.736,2.109],[-2.189,2.109],[-2.207,2.123],[-2.436,2.128],[-2.434,2.042],[-2.455,2.021],[-2.576,2.021],[-2.597,2.042],[-2.597,2.084],[-2.633,2.114],[-2.946,2.109],[-2.99,2.06]],"front":[[-0.873,0.001],[-0.855,-0.027],[-0.869,-0.041],[-0.873,-0.139],[-0.82,-0.132],[-0.787,-0.17],[-0.731,-0.174],[-0.675,-0.221],[-0.358,-0.207],[-0.327,-0.167],[-0.388,-0.093],[-0.306,0.003],[0.347,0.003],[0.442,-0.088],[0.363,-0.177],[0.363,-0.214],[0.561,-0.221],[0.596,-0.186],[0.596,0.192],[0.657,0.374],[0.652,0.63],[0.608,0.689],[0.57,0.707],[0.319,0.712],[0.298,0.733],[0.505,0.875],[0.673,1.099],[0.787,1.092],[0.783,1.722],[0.673,1.724],[0.522,1.927],[0.312,2.086],[0.312,2.188],[0.295,2.2],[-0.302,2.2],[-0.313,2.188],[-0.313,2.086],[-0.484,1.967],[-0.556,1.894],[-0.687,1.703],[-0.729,1.582],[-0.719,1.549],[-0.738,1.493],[-0.738,1.405],[-0.752,1.391],[-0.738,1.377],[-0.715,1.195],[-0.687,1.12],[-0.561,0.933],[-0.456,0.833],[-0.295,0.728],[-0.295,0.458],[-0.313,0.439],[-0.295,0.42],[-0.281,0.346],[-0.239,0.308],[-0.26,0.287],[-0.563,0.287],[-0.619,0.231],[-0.675,0.236],[-0.703,0.213],[-0.782,0.208],[-0.82,0.171],[-0.862,0.171],[-0.859,0.052]]},"features":{"side":{},"front":{}},"placement":{"side":{"plane":"xy","offset":{}},"front":{"plane":"zy","offset":{}}},"bounds":{"min":[-2.995,-0.221,-0.873],"max":[1.046,2.2,0.786]},"axis_y":1.41,"axis_z":0,"volume_in3":7.5176,"centroid":[-0.8074,1.2113,0.0104],"shell":[-0.6083,0.9314,0.0039],"area_in2":40.6955,"triangles":21350,"manifold":true,"rail_seat":{"x":[-0.765,0.965],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-2.999,0.692,-0.718,-1.159,2.128,0.734],[-1.159,-0.163,-0.794,-0.79,2.163,0.734],[-0.79,-0.221,-0.853,-0.054,2.2,0.786],[-0.054,-0.221,-0.873,0.314,2.147,0.718],[0.314,-0.221,-0.681,1.05,2.091,0.681]],"slots":["body","mount","hardware","lens"]},"holosun-hs510c":{"part":"holosun-hs510c","model":"holosun-hs510c.glb","script":"holosun_hs510c.py","inputs":{"holosun-hs510c.clamp_below_rail":0.219,"holosun-hs510c.clamp_bottom_y":-0.219,"holosun-hs510c.height":2.31,"holosun-hs510c.length":3.3,"holosun-hs510c.optical_axis_above_rail":1.41,"holosun-hs510c.rail_middle_z":-0.0255,"holosun-hs510c.width":1.8,"holosun-hs510c.window_center_above_base":1.04,"holosun-hs510c.window_width":1.26,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{"side":[[-1.83,1.134],[-1.83,0.887],[-1.821,0.873],[-1.83,0.859],[-1.807,0.836],[-1.723,0.622],[-1.716,0.47],[-1.474,0.466],[-1.362,0.419],[-1.323,0.384],[-1.346,0.361],[-1.341,0.109],[-1.32,0.098],[-1.148,0.102],[-1.067,0.012],[-1.069,0],[-1.05,0.014],[-1.036,0],[-1.022,0.009],[-0.999,0],[-0.976,0.009],[-0.966,0],[-0.957,0.009],[1.055,0.014],[1.092,0.033],[1.118,0.063],[1.449,0.533],[1.439,0.543],[1.439,0.589],[1.463,0.612],[1.463,1.167],[1.199,2.31],[0.203,2.315],[0.191,2.28],[0.177,2.103],[0.154,1.991],[0.102,1.833],[0.028,1.674],[-0.056,1.539],[-0.154,1.418],[-0.272,1.3],[-0.403,1.197],[-0.533,1.118],[-0.585,1.099],[-0.929,1.099],[-0.999,1.206],[-1.8,1.206],[-1.826,1.171]],"front":[[-0.851,0.593],[-0.831,0.6],[-0.819,0.589],[-0.828,0.556],[-0.81,0.523],[-0.647,0.356],[-0.675,0.272],[-0.675,0.193],[-0.647,0.1],[-0.647,0.044],[-0.603,0],[-0.37,0.005],[-0.377,0.054],[-0.442,0.119],[-0.442,0.128],[-0.351,0.219],[0.319,0.219],[0.34,0.174],[0.391,0.123],[0.391,0.114],[0.33,0.054],[0.34,0.03],[0.365,0.009],[0.468,0.009],[0.482,0],[0.612,0],[0.651,0.035],[0.656,0.058],[0.677,0.074],[0.854,0.07],[0.891,0.093],[0.938,0.093],[0.954,0.123],[0.954,0.337],[0.945,0.356],[0.928,0.368],[0.886,0.368],[0.863,0.386],[0.7,0.386],[0.689,0.398],[0.81,0.519],[0.819,0.533],[0.819,0.584],[0.838,0.603],[0.838,1.119],[0.814,1.221],[0.81,1.901],[0.805,1.961],[0.777,2.04],[0.7,2.136],[0.63,2.178],[0.547,2.21],[0.277,2.28],[0.03,2.303],[-0.212,2.289],[-0.458,2.238],[-0.663,2.159],[-0.726,2.11],[-0.777,2.036],[-0.8,1.97],[-0.81,1.896],[-0.814,1.212],[-0.833,1.128],[-0.833,0.612]],"plan":[[0,0.847],[0.007,0.595],[0.104,0.121],[0.113,0.098],[0.144,0.076],[0.265,0.069],[0.785,0.074],[1.025,0.06],[1.087,0.012],[1.58,0.009],[1.616,0.03],[1.653,0.03],[2.617,0.012],[2.867,0.018],[2.924,0.005],[3.243,0],[3.287,0.007],[3.298,0.036],[3.291,0.075],[3.288,1.582],[3.3,1.623],[3.283,1.657],[2.834,1.652],[2.797,1.641],[2.673,1.638],[2.437,1.666],[2.125,1.668],[2.11,1.764],[2.096,1.794],[2.026,1.839],[1.963,1.849],[1.903,1.828],[1.845,1.77],[1.799,1.74],[1.402,1.692],[1.374,1.675],[1.344,1.685],[1.325,1.671],[1.293,1.68],[1.274,1.666],[1.238,1.675],[1.224,1.662],[1.207,1.673],[1.187,1.673],[1.17,1.659],[1.143,1.673],[1.122,1.659],[1.087,1.671],[1.069,1.659],[1.039,1.673],[1.018,1.659],[0.99,1.675],[0.967,1.662],[0.946,1.678],[0.914,1.666],[0.895,1.682],[0.865,1.668],[0.845,1.687],[0.815,1.675],[0.791,1.694],[0.764,1.682],[0.745,1.701],[0.72,1.694],[0.681,1.724],[0.581,1.731],[0.56,1.719],[0.54,1.742],[0.496,1.74],[0.471,1.714],[0.471,1.679],[0.505,1.641],[0.525,1.635],[0.53,1.615],[0.55,1.607],[0.555,1.584],[0.573,1.575],[0.567,1.564],[0.144,1.555],[0.104,1.529],[0.002,1.034]],"left":[[-1.829,1.194],[-1.826,0.875],[-1.769,0.613],[-1.756,0.596],[-1.762,0.588],[-1.758,0.472],[-1.489,0.452],[-1.427,0.43],[-1.359,0.392],[-1.323,0.361],[-1.325,0.234],[-1.317,0.172],[-1.299,0.154],[-1.226,0.152],[-1.217,0.141],[-1.185,0.141],[-1.126,0.044],[-1.102,0.021],[-1.072,0.006],[-1.035,0.002],[-0.001,0.002],[0.082,0],[1.04,0.002],[1.082,0.011],[1.135,0.055],[1.31,0.307],[1.46,0.494],[1.482,0.536],[1.48,0.579],[1.471,0.59],[1.492,0.603],[1.488,1.222],[1.287,2.102],[1.22,2.269],[1.196,2.293],[0.436,2.295],[0.206,2.294],[0.191,2.153],[0.139,1.943],[0.079,1.787],[-0.034,1.583],[-0.135,1.453],[-0.241,1.343],[-0.378,1.229],[-0.545,1.12],[-0.92,1.12],[-0.992,1.214],[-1.02,1.216],[-1.725,1.22],[-1.806,1.216]]},"features":{"side":{"mount":[[[-1.712,0.617],[1.451,0.617],[1.451,0.533],[1.129,-0.002],[-1.102,-0.002],[-1.325,0.179],[-1.325,0.422],[-1.516,0.468],[-1.712,0.477]]],"lever":[[[-1.344,0.384],[-0.491,0.384],[-0.491,0.445],[0.743,0.445],[0.743,0.026],[-0.491,0.026],[-0.491,0.105],[-1.344,0.105]]],"lever_ribs":[[[-1.288,0.384],[-0.435,0.384],[-0.435,0.105],[-1.288,0.105]]],"hood":[[[0.193,2.317],[1.195,2.317],[1.46,1.223],[1.46,1.209],[-0.342,1.209],[-0.259,1.283],[-0.142,1.4],[0.021,1.633],[0.137,1.865],[0.184,2.098]]],"glass":[[[1.167,2.317],[1.432,1.223],[1.386,1.223],[1.12,2.317]]],"tray":[[[-0.305,0.994],[1.139,0.994],[1.139,0.668],[-0.305,0.668]]],"tray_tab":[[[0.161,1.064],[0.673,1.064],[0.673,0.994],[0.161,0.994]]],"tray_screws":[[[-0.212,0.897],[-0.1,0.897],[-0.1,0.785],[-0.212,0.785]],[[0.934,0.897],[1.046,0.897],[1.046,0.785],[0.934,0.785]]],"housing_screws":[[[-0.65,0.953],[-0.398,0.953],[-0.398,0.701],[-0.65,0.701]],[[1.171,0.953],[1.423,0.953],[1.423,0.701],[1.171,0.701]]],"windage":[[[-1.493,1.036],[-1.167,1.036],[-1.167,0.71],[-1.493,0.71]],[[-1.437,0.98],[-1.223,0.98],[-1.223,0.766],[-1.437,0.766]]],"deck_chamfer":[[[-1.712,1.181],[-0.585,1.181],[-0.585,1.088],[-1.712,1.088]]],"deck_corner":[[[-1.418,1.092],[-1.66,0.813],[-1.819,1.185]]],"solar":[[[-0.92,1.129],[-0.594,1.129],[-0.594,1.092],[-0.92,1.092]]],"windage_slot":[[[-1.348,0.971],[-1.306,0.971],[-1.306,0.771],[-1.348,0.771]]],"housing_screw_heads":[[[-0.603,0.906],[-0.445,0.906],[-0.445,0.748],[-0.603,0.748]],[[1.218,0.906],[1.376,0.906],[1.376,0.748],[1.218,0.748]]]},"front":{"window":[[[0.628,1.273],[0.628,1.901],[0.6,1.966],[0.542,2.019],[0.426,2.061],[0.244,2.103],[0.072,2.122],[-0.072,2.122],[-0.272,2.098],[-0.454,2.052],[-0.523,2.029],[-0.565,2.001],[-0.61,1.947],[-0.628,1.896],[-0.628,1.282],[-0.61,1.226],[-0.57,1.177],[-0.519,1.145],[-0.458,1.131],[0.458,1.131],[0.523,1.145],[0.561,1.168],[0.605,1.217]]],"panel":[[[0.721,0.612],[0.721,1.077],[0.714,1.084],[-0.714,1.084],[-0.721,1.077],[-0.721,0.612],[-0.71,0.6],[0.714,0.605]]],"lever":[[[0.952,0.398],[0.649,0.398],[0.649,0.04],[0.952,0.04]]],"bolt":[[[-0.658,0.365],[-0.691,0.365],[-0.691,0.077],[-0.658,0.077]]],"bar":[[[0.416,0.375],[-0.416,0.375],[-0.416,0.216],[0.416,0.216]]]},"plan":{"lever":[[[2.109,1.561],[2.104,1.792],[2.062,1.838],[1.982,1.845],[1.901,1.815],[1.866,1.778],[1.381,1.688],[1.173,1.674],[0.676,1.674],[0.618,1.72],[0.503,1.739],[0.475,1.688],[0.491,1.561]]],"bar":[[[2.086,1.203],[2.086,0.382],[1.889,0.382],[1.889,1.203]]]},"left":{"pad":[[[0.898,1.072],[-0.055,1.072],[-0.307,0.825],[-0.194,0.622],[0.984,0.622],[1.102,0.714],[1.106,0.832]]],"buttons":[[[0.873,0.999],[0.539,0.999],[0.539,0.665],[0.873,0.665]],[[0.294,1.01],[-0.04,1.01],[-0.04,0.676],[0.294,0.676]]],"plus":[[[0.791,0.845],[0.62,0.845],[0.62,0.819],[0.791,0.819]],[[0.718,0.917],[0.693,0.917],[0.693,0.746],[0.718,0.746]]],"minus":[[[0.213,0.855],[0.042,0.855],[0.042,0.83],[0.213,0.83]]],"screws":[[[1.455,0.907],[1.241,0.907],[1.241,0.693],[1.455,0.693]],[[-0.376,0.917],[-0.59,0.917],[-0.59,0.703],[-0.376,0.703]]],"bolt":[[[0.331,0.404],[-0.033,0.404],[-0.033,0.04],[0.331,0.04]]],"gap":[[[0.518,0.592],[-0.286,0.597],[-0.291,0.592],[-0.187,0.492],[-0.08,0.492],[-0.074,0.499],[0.414,0.492]]]}},"placement":{"side":{"plane":"xy","offset":{"y":"clamp_bottom_y"}},"front":{"plane":"zy","offset":{"y":"clamp_bottom_y"}},"plan":{"plane":"xz","offset":{}},"left":{"plane":"xy","offset":{"y":"clamp_bottom_y"}}},"bounds":{"min":[-1.8299,-0.219,-0.851],"max":[1.463,2.084,0.952]},"axis_y":1.41,"volume_in3":5.4143,"centroid":[0.0189,0.605,0.0202],"shell":[0.1522,0.7563,0.0162],"area_in2":40.2609,"triangles":20664,"manifold":true,"rail_seat":{"x":[-1.325,1.129],"top_y":0,"centre_z":-0.0255,"to_y":-0.154,"reach":0.4525},"slabs":[[-1.83,0.236,-0.851,-1.464,0.987,0.838],[-1.464,-0.219,-0.851,-1.098,0.987,0.911],[-1.098,-0.219,-0.851,-0.366,1.007,0.875],[-0.366,-0.219,-0.851,-0.001,1.409,0.944],[-0.001,-0.219,-0.851,0.365,2.084,0.952],[0.365,-0.219,-0.851,1.463,2.084,0.844]],"slots":["body","tray","pad","screws","solar","lens"]},"huxwrx-flash-hider-qd-556":{"part":"huxwrx-flash-hider-qd-556","model":"huxwrx-flash-hider-qd-556.glb","script":"huxwrx_flash_hider_qd_556.py","inputs":{"huxwrx-flash-hider-qd-556.body_d":0.895,"huxwrx-flash-hider-qd-556.body_x":0.669,"huxwrx-flash-hider-qd-556.bore_d":0.275,"huxwrx-flash-hider-qd-556.cone_rear_d":1.015,"huxwrx-flash-hider-qd-556.cone_rear_x":0.465,"huxwrx-flash-hider-qd-556.core_notch_depth":0.08,"huxwrx-flash-hider-qd-556.core_od":0.434,"huxwrx-flash-hider-qd-556.core_recess":0.03,"huxwrx-flash-hider-qd-556.cross_hole_d":0.123,"huxwrx-flash-hider-qd-556.hex_across_flats":1.04,"huxwrx-flash-hider-qd-556.hex_thickness":0.145,"huxwrx-flash-hider-qd-556.length":2.3,"huxwrx-flash-hider-qd-556.neck_d":1.015,"huxwrx-flash-hider-qd-556.neck_length":0.047,"huxwrx-flash-hider-qd-556.od":1.2,"huxwrx-flash-hider-qd-556.qd_thread_length":0.236,"huxwrx-flash-hider-qd-556.qd_thread_od":1.123,"huxwrx-flash-hider-qd-556.qd_thread_pitch":0.083,"huxwrx-flash-hider-qd-556.rear_hole_circle_d":0.82,"huxwrx-flash-hider-qd-556.rear_hole_d":0.16,"huxwrx-flash-hider-qd-556.rear_holes":9,"huxwrx-flash-hider-qd-556.ring_id":0.77,"huxwrx-flash-hider-qd-556.slot_front_x":2.11,"huxwrx-flash-hider-qd-556.slot_rear_x":0.663,"huxwrx-flash-hider-qd-556.slot_taper_x":1.55,"huxwrx-flash-hider-qd-556.slot_twist":35,"huxwrx-flash-hider-qd-556.slot_width":45,"huxwrx-flash-hider-qd-556.slots":6,"huxwrx-flash-hider-qd-556.suppressor_seat_x":0.145,"huxwrx-flash-hider-qd-556.thread_length":0.6,"huxwrx-flash-hider-qd-556.thread_major_d":0.5},"profiles":{},"bounds":{"min":[0,-0.5615,-0.6],"max":[2.3,0.5615,0.6]},"volume_in3":0.6642,"centroid":[0.8234,-0.001,-0.0005],"shell":[1.0716,-0.0011,-0.0007],"area_in2":14.7822,"triangles":32242,"manifold":true,"slabs":[[0,-0.561,-0.6,0.383,0.561,0.6],[0.383,-0.549,-0.555,0.767,0.528,0.519],[0.767,-0.447,-0.447,2.3,0.447,0.447]],"slots":["body"]},"huxwrx-flow-556-ti":{"part":"huxwrx-flow-556-ti","model":"huxwrx-flow-556-ti.glb","script":"huxwrx_flow_556_ti.py","inputs":{"huxwrx-flash-hider-qd-556.body_d":0.895,"huxwrx-flash-hider-qd-556.body_x":0.669,"huxwrx-flash-hider-qd-556.cone_rear_d":1.015,"huxwrx-flash-hider-qd-556.cone_rear_x":0.465,"huxwrx-flash-hider-qd-556.hex_thickness":0.145,"huxwrx-flash-hider-qd-556.length":2.3,"huxwrx-flash-hider-qd-556.neck_d":1.015,"huxwrx-flash-hider-qd-556.neck_length":0.047,"huxwrx-flash-hider-qd-556.qd_thread_length":0.236,"huxwrx-flash-hider-qd-556.qd_thread_od":1.123,"huxwrx-flash-hider-qd-556.qd_thread_pitch":0.083,"huxwrx-flash-hider-qd-556.suppressor_seat_x":0.145,"huxwrx-flow-556-ti.bore_d":0.281,"huxwrx-flow-556-ti.cap_slot_lean":50,"huxwrx-flow-556-ti.cap_slot_r_in":0.645,"huxwrx-flow-556-ti.cap_slot_r_out":0.87,"huxwrx-flow-556-ti.cap_slot_width":0.14,"huxwrx-flow-556-ti.cap_slots":16,"huxwrx-flow-556-ti.collar_across_flats":1.3,"huxwrx-flow-556-ti.collar_corner_r":0.3,"huxwrx-flow-556-ti.collar_length":0.237,"huxwrx-flow-556-ti.grip_columns":20,"huxwrx-flow-556-ti.grip_dash_length":0.38,"huxwrx-flow-556-ti.grip_dash_width":0.07,"huxwrx-flow-556-ti.grip_first_x":0.418,"huxwrx-flow-556-ti.grip_pitch":0.686,"huxwrx-flow-556-ti.grip_ranks":3,"huxwrx-flow-556-ti.grip_stagger":0.2,"huxwrx-flow-556-ti.grip_texture":0.05,"huxwrx-flow-556-ti.length":6.8,"huxwrx-flow-556-ti.nose_boss_d":0.38,"huxwrx-flow-556-ti.nose_rib_width":0.164,"huxwrx-flow-556-ti.od":1.8},"profiles":{"side":[[0,0.621],[0,-0.001],[0,-0.621],[0.01,-0.639],[0.029,-0.65],[0.24,-0.65],[0.296,-0.663],[0.337,-0.683],[0.358,-0.705],[0.362,-0.727],[0.39,-0.744],[0.441,-0.788],[0.456,-0.79],[0.466,-0.798],[0.509,-0.844],[0.542,-0.864],[0.56,-0.861],[0.577,-0.878],[0.581,-0.892],[0.619,-0.91],[0.654,-0.92],[0.692,-0.925],[0.774,-0.925],[0.802,-0.904],[1.056,-0.904],[1.079,-0.922],[1.226,-0.922],[1.485,-0.917],[1.503,-0.904],[1.759,-0.904],[1.77,-0.912],[1.94,-0.912],[2.207,-0.904],[6.023,-0.904],[6.071,-0.899],[6.114,-0.889],[6.175,-0.866],[6.272,-0.816],[6.34,-0.77],[6.364,-0.746],[6.484,-0.593],[6.552,-0.497],[6.789,-0.187],[6.801,-0.151],[6.799,0.017],[6.688,0.091],[6.669,0.111],[6.686,0.127],[6.79,0.127],[6.801,0.136],[6.801,0.171],[6.796,0.192],[6.762,0.236],[6.734,0.239],[6.706,0.254],[6.564,0.351],[6.524,0.387],[6.499,0.431],[6.499,0.57],[6.375,0.733],[6.34,0.77],[6.272,0.816],[6.175,0.866],[6.107,0.892],[6.053,0.902],[2.207,0.904],[1.942,0.912],[1.772,0.912],[1.759,0.904],[1.505,0.904],[1.485,0.917],[1.231,0.922],[1.079,0.922],[1.056,0.904],[0.802,0.904],[0.774,0.925],[0.69,0.925],[0.634,0.915],[0.581,0.892],[0.577,0.878],[0.56,0.861],[0.542,0.864],[0.509,0.844],[0.456,0.79],[0.441,0.788],[0.39,0.744],[0.362,0.727],[0.358,0.705],[0.339,0.686],[0.309,0.668],[0.24,0.65],[0.029,0.65],[0.005,0.634]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{}}},"bounds":{"min":[0,-0.9191,-0.9191],"max":[6.8,0.9191,0.9191]},"volume_in3":14.0309,"centroid":[3.4894,0,0],"shell":[2.7807,-0.0003,-0.0001],"area_in2":70.1268,"triangles":46128,"manifold":true,"slabs":[[0,-0.733,-0.733,0.378,0.733,0.733],[0.378,-0.919,-0.919,6.422,0.919,0.919],[6.422,-0.668,-0.668,6.8,0.668,0.668]],"slots":["body","socket"]},"huxwrx-flow-556k":{"part":"huxwrx-flow-556k","model":"huxwrx-flow-556k.glb","script":"huxwrx_flow_556k.py","inputs":{"huxwrx-flash-hider-qd-556.body_d":0.895,"huxwrx-flash-hider-qd-556.body_x":0.669,"huxwrx-flash-hider-qd-556.cone_rear_d":1.015,"huxwrx-flash-hider-qd-556.cone_rear_x":0.465,"huxwrx-flash-hider-qd-556.hex_thickness":0.145,"huxwrx-flash-hider-qd-556.length":2.3,"huxwrx-flash-hider-qd-556.neck_d":1.015,"huxwrx-flash-hider-qd-556.neck_length":0.047,"huxwrx-flash-hider-qd-556.qd_thread_length":0.236,"huxwrx-flash-hider-qd-556.qd_thread_od":1.123,"huxwrx-flash-hider-qd-556.qd_thread_pitch":0.083,"huxwrx-flash-hider-qd-556.suppressor_seat_x":0.145,"huxwrx-flow-556k.bore_d":0.277,"huxwrx-flow-556k.cap_slot_lean":15,"huxwrx-flow-556k.cap_slot_r_in":0.52,"huxwrx-flow-556k.cap_slot_r_out":0.77,"huxwrx-flow-556k.cap_slot_width":0.125,"huxwrx-flow-556k.cap_slots":18,"huxwrx-flow-556k.collar_across_flats":1.283,"huxwrx-flow-556k.collar_corner_r":0.3,"huxwrx-flow-556k.collar_length":0.244,"huxwrx-flow-556k.grip_columns":20,"huxwrx-flow-556k.grip_dash_length":0.36,"huxwrx-flow-556k.grip_dash_width":0.065,"huxwrx-flow-556k.grip_first_x":0.405,"huxwrx-flow-556k.grip_pitch":0.672,"huxwrx-flow-556k.grip_ranks":3,"huxwrx-flow-556k.grip_stagger":0.188,"huxwrx-flow-556k.grip_texture":0.05,"huxwrx-flow-556k.length":5.5,"huxwrx-flow-556k.nose_boss_d":0.44,"huxwrx-flow-556k.nose_rib_width":0.154,"huxwrx-flow-556k.od":1.6},"profiles":{"side":[[0,0.608],[0,0],[0,-0.61],[0.017,-0.636],[0.036,-0.642],[0.244,-0.642],[0.299,-0.653],[0.352,-0.673],[0.37,-0.692],[0.374,-0.702],[0.488,-0.757],[0.576,-0.79],[0.616,-0.799],[0.955,-0.801],[0.966,-0.792],[1.044,-0.792],[1.057,-0.801],[1.196,-0.801],[1.639,-0.792],[4.87,-0.792],[4.973,-0.775],[5.019,-0.761],[5.061,-0.742],[5.111,-0.699],[5.272,-0.494],[5.274,-0.388],[5.292,-0.355],[5.33,-0.316],[5.46,-0.226],[5.486,-0.196],[5.492,-0.174],[5.491,-0.131],[5.48,-0.125],[5.396,-0.125],[5.382,-0.11],[5.396,-0.096],[5.476,-0.043],[5.49,-0.02],[5.492,0.154],[5.479,0.207],[5.461,0.238],[5.331,0.408],[5.263,0.505],[5.107,0.703],[5.077,0.731],[5.028,0.757],[4.978,0.772],[4.883,0.79],[1.628,0.792],[1.118,0.801],[1.061,0.801],[1.046,0.792],[0.964,0.792],[0.951,0.801],[0.64,0.801],[0.572,0.788],[0.495,0.759],[0.376,0.702],[0.37,0.69],[0.354,0.673],[0.294,0.651],[0.226,0.64],[0.03,0.64],[0.007,0.626]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{}}},"bounds":{"min":[0,-0.8199,-0.8199],"max":[5.5,0.8199,0.8199]},"volume_in3":8.549,"centroid":[2.895,0.0001,0],"shell":[2.2188,-0.0003,-0.0002],"area_in2":57.622,"triangles":44206,"manifold":true,"slabs":[[0,-0.718,-0.718,0.393,0.718,0.718],[0.393,-0.82,-0.82,5.107,0.82,0.82],[5.107,-0.715,-0.717,5.5,0.715,0.717]],"slots":["body","socket"]},"jp-silent-captured-spring-gen2-h2":{"part":"jp-silent-captured-spring-gen2-h2","model":"jp-silent-captured-spring-gen2-h2.glb","script":"jp_silent_captured_spring_gen2.py","inputs":{"jp-silent-captured-spring-gen2-h2.bumper_front_d":0.918,"jp-silent-captured-spring-gen2-h2.bumper_front_round":0.06,"jp-silent-captured-spring-gen2-h2.bumper_length":0.979,"jp-silent-captured-spring-gen2-h2.bumper_rear_d":0.993,"jp-silent-captured-spring-gen2-h2.cap_d":0.996,"jp-silent-captured-spring-gen2-h2.cap_length":0.116,"jp-silent-captured-spring-gen2-h2.cap_pocket_d":0.42,"jp-silent-captured-spring-gen2-h2.cap_round":0.035,"jp-silent-captured-spring-gen2-h2.cap_spigot_d":0.7,"jp-silent-captured-spring-gen2-h2.carrier_channel_min":0.53,"jp-silent-captured-spring-gen2-h2.coils":25,"jp-silent-captured-spring-gen2-h2.collar_d":0.805,"jp-silent-captured-spring-gen2-h2.collar_length":0.164,"jp-silent-captured-spring-gen2-h2.flange_d":0.993,"jp-silent-captured-spring-gen2-h2.flange_length":0.209,"jp-silent-captured-spring-gen2-h2.flange_round":0.045,"jp-silent-captured-spring-gen2-h2.front_bore_d":0.546,"jp-silent-captured-spring-gen2-h2.front_bore_depth":0.25,"jp-silent-captured-spring-gen2-h2.hex_socket":0.125,"jp-silent-captured-spring-gen2-h2.inner_flange":0.1,"jp-silent-captured-spring-gen2-h2.installed_length":7.226,"jp-silent-captured-spring-gen2-h2.length":7.249,"jp-silent-captured-spring-gen2-h2.mass_bore_d":0.805,"jp-silent-captured-spring-gen2-h2.mass_chamfer":0.014,"jp-silent-captured-spring-gen2-h2.mass_count":3,"jp-silent-captured-spring-gen2-h2.mass_length":0.572,"jp-silent-captured-spring-gen2-h2.od":0.966,"jp-silent-captured-spring-gen2-h2.oring_d":0.942,"jp-silent-captured-spring-gen2-h2.oring_gap":0.072,"jp-silent-captured-spring-gen2-h2.pocket_depth":0.05,"jp-silent-captured-spring-gen2-h2.protrusion":0.03,"jp-silent-captured-spring-gen2-h2.rod_d":0.377,"jp-silent-captured-spring-gen2-h2.screw_head_d":0.36,"jp-silent-captured-spring-gen2-h2.slider_bore_d":0.53,"jp-silent-captured-spring-gen2-h2.snap_ring_d":0.897,"jp-silent-captured-spring-gen2-h2.snap_ring_length":0.062,"jp-silent-captured-spring-gen2-h2.spring_od":0.51,"jp-silent-captured-spring-gen2-h2.tungsten_count":2,"jp-silent-captured-spring-gen2-h2.wire_d":0.047,"std.receiver_extension.bore_d":1},"profiles":{},"bounds":{"min":[0,-0.498,-0.498],"max":[7.226,0.498,0.498]},"volume_in3":2.5986,"centroid":[3.2024,0,0],"shell":[3.0909,-0.0001,0],"area_in2":52.7844,"triangles":43394,"manifold":true,"slabs":[[0,-0.496,-0.496,2.282,0.496,0.496],[2.282,-0.403,-0.403,2.662,0.403,0.403],[2.662,-0.256,-0.256,6.085,0.256,0.256],[6.085,-0.498,-0.498,7.226,0.498,0.498]],"slots":["body","tungsten","weights","orings","hardware","rod","spring","bumper"]},"jp-silent-captured-spring-gen2-h3":{"part":"jp-silent-captured-spring-gen2-h3","model":"jp-silent-captured-spring-gen2-h3.glb","script":"jp_silent_captured_spring_gen2.py","inputs":{"jp-silent-captured-spring-gen2-h3.bumper_front_d":0.918,"jp-silent-captured-spring-gen2-h3.bumper_front_round":0.06,"jp-silent-captured-spring-gen2-h3.bumper_length":0.979,"jp-silent-captured-spring-gen2-h3.bumper_rear_d":0.993,"jp-silent-captured-spring-gen2-h3.cap_d":0.996,"jp-silent-captured-spring-gen2-h3.cap_length":0.116,"jp-silent-captured-spring-gen2-h3.cap_pocket_d":0.42,"jp-silent-captured-spring-gen2-h3.cap_round":0.035,"jp-silent-captured-spring-gen2-h3.cap_spigot_d":0.7,"jp-silent-captured-spring-gen2-h3.carrier_channel_min":0.53,"jp-silent-captured-spring-gen2-h3.coils":25,"jp-silent-captured-spring-gen2-h3.collar_d":0.805,"jp-silent-captured-spring-gen2-h3.collar_length":0.164,"jp-silent-captured-spring-gen2-h3.flange_d":0.993,"jp-silent-captured-spring-gen2-h3.flange_length":0.209,"jp-silent-captured-spring-gen2-h3.flange_round":0.045,"jp-silent-captured-spring-gen2-h3.front_bore_d":0.546,"jp-silent-captured-spring-gen2-h3.front_bore_depth":0.25,"jp-silent-captured-spring-gen2-h3.hex_socket":0.125,"jp-silent-captured-spring-gen2-h3.inner_flange":0.1,"jp-silent-captured-spring-gen2-h3.installed_length":7.226,"jp-silent-captured-spring-gen2-h3.length":7.249,"jp-silent-captured-spring-gen2-h3.mass_bore_d":0.805,"jp-silent-captured-spring-gen2-h3.mass_chamfer":0.014,"jp-silent-captured-spring-gen2-h3.mass_count":3,"jp-silent-captured-spring-gen2-h3.mass_length":0.572,"jp-silent-captured-spring-gen2-h3.od":0.966,"jp-silent-captured-spring-gen2-h3.oring_d":0.942,"jp-silent-captured-spring-gen2-h3.oring_gap":0.072,"jp-silent-captured-spring-gen2-h3.pocket_depth":0.05,"jp-silent-captured-spring-gen2-h3.protrusion":0.03,"jp-silent-captured-spring-gen2-h3.rod_d":0.377,"jp-silent-captured-spring-gen2-h3.screw_head_d":0.36,"jp-silent-captured-spring-gen2-h3.slider_bore_d":0.53,"jp-silent-captured-spring-gen2-h3.snap_ring_d":0.897,"jp-silent-captured-spring-gen2-h3.snap_ring_length":0.062,"jp-silent-captured-spring-gen2-h3.spring_od":0.51,"jp-silent-captured-spring-gen2-h3.tungsten_count":3,"jp-silent-captured-spring-gen2-h3.wire_d":0.047,"std.receiver_extension.bore_d":1},"profiles":{},"bounds":{"min":[0,-0.498,-0.498],"max":[7.226,0.498,0.498]},"volume_in3":2.5986,"centroid":[3.2024,0,0],"shell":[3.0909,-0.0001,0],"area_in2":52.7844,"triangles":43394,"manifold":true,"slabs":[[0,-0.496,-0.496,2.282,0.496,0.496],[2.282,-0.403,-0.403,2.662,0.403,0.403],[2.662,-0.256,-0.256,6.085,0.256,0.256],[6.085,-0.498,-0.498,7.226,0.498,0.498]],"slots":["body","tungsten","orings","hardware","rod","spring","bumper"]},"jp-silent-captured-spring-gen2":{"part":"jp-silent-captured-spring-gen2","model":"jp-silent-captured-spring-gen2.glb","script":"jp_silent_captured_spring_gen2.py","inputs":{"jp-silent-captured-spring-gen2.bumper_front_d":0.918,"jp-silent-captured-spring-gen2.bumper_front_round":0.06,"jp-silent-captured-spring-gen2.bumper_length":0.979,"jp-silent-captured-spring-gen2.bumper_rear_d":0.993,"jp-silent-captured-spring-gen2.cap_d":0.996,"jp-silent-captured-spring-gen2.cap_length":0.116,"jp-silent-captured-spring-gen2.cap_pocket_d":0.42,"jp-silent-captured-spring-gen2.cap_round":0.035,"jp-silent-captured-spring-gen2.cap_spigot_d":0.7,"jp-silent-captured-spring-gen2.carrier_channel_min":0.53,"jp-silent-captured-spring-gen2.coils":30.5,"jp-silent-captured-spring-gen2.collar_d":0.805,"jp-silent-captured-spring-gen2.collar_length":0.164,"jp-silent-captured-spring-gen2.flange_d":0.993,"jp-silent-captured-spring-gen2.flange_length":0.209,"jp-silent-captured-spring-gen2.flange_round":0.045,"jp-silent-captured-spring-gen2.front_bore_d":0.546,"jp-silent-captured-spring-gen2.front_bore_depth":0.25,"jp-silent-captured-spring-gen2.hex_socket":0.125,"jp-silent-captured-spring-gen2.inner_flange":0.1,"jp-silent-captured-spring-gen2.installed_length":7.226,"jp-silent-captured-spring-gen2.length":7.249,"jp-silent-captured-spring-gen2.mass_bore_d":0.805,"jp-silent-captured-spring-gen2.mass_chamfer":0.014,"jp-silent-captured-spring-gen2.mass_count":3,"jp-silent-captured-spring-gen2.mass_length":0.572,"jp-silent-captured-spring-gen2.od":0.966,"jp-silent-captured-spring-gen2.oring_d":0.942,"jp-silent-captured-spring-gen2.oring_gap":0.072,"jp-silent-captured-spring-gen2.pocket_depth":0.05,"jp-silent-captured-spring-gen2.protrusion":0.03,"jp-silent-captured-spring-gen2.rod_d":0.377,"jp-silent-captured-spring-gen2.screw_head_d":0.36,"jp-silent-captured-spring-gen2.slider_bore_d":0.53,"jp-silent-captured-spring-gen2.snap_ring_d":0.897,"jp-silent-captured-spring-gen2.snap_ring_length":0.062,"jp-silent-captured-spring-gen2.spring_od":0.51,"jp-silent-captured-spring-gen2.tungsten_count":0,"jp-silent-captured-spring-gen2.wire_d":0.047,"std.receiver_extension.bore_d":1},"profiles":{},"bounds":{"min":[0,-0.498,-0.498],"max":[7.226,0.498,0.498]},"volume_in3":2.6232,"centroid":[3.2074,0,0],"shell":[3.116,-0.0001,0.0001],"area_in2":54.9451,"triangles":48450,"manifold":true,"slabs":[[0,-0.496,-0.496,2.282,0.496,0.496],[2.282,-0.403,-0.403,2.662,0.403,0.403],[2.662,-0.256,-0.256,6.085,0.256,0.256],[6.085,-0.498,-0.498,7.226,0.498,0.498]],"slots":["body","weights","orings","hardware","rod","spring","bumper"]},"kynshot-rb5000":{"part":"kynshot-rb5000","model":"kynshot-rb5000.glb","script":"kynshot_rb5000.py","inputs":{"kynshot-rb5000.body_front_chamfer":0.025,"kynshot-rb5000.body_length":2.666,"kynshot-rb5000.body_rear_chamfer":0.02,"kynshot-rb5000.bumper_d":0.67,"kynshot-rb5000.bumper_end_d":0.53,"kynshot-rb5000.bumper_exposed":0.279,"kynshot-rb5000.bumper_round":0.045,"kynshot-rb5000.head_back_d":0.79,"kynshot-rb5000.head_d":0.951,"kynshot-rb5000.head_flat_across":0.924,"kynshot-rb5000.head_flats":3,"kynshot-rb5000.head_front_chamfer":0.015,"kynshot-rb5000.head_rim":0.193,"kynshot-rb5000.head_thickness":0.244,"kynshot-rb5000.hub_chamfer":0.017,"kynshot-rb5000.hub_d":0.74,"kynshot-rb5000.hub_hole_d":0.09,"kynshot-rb5000.hub_length":0.136,"kynshot-rb5000.length":3.65,"kynshot-rb5000.mouth_depth":0.06,"kynshot-rb5000.mouth_wall":0.04,"kynshot-rb5000.od":0.69,"kynshot-rb5000.rod_d":0.167,"kynshot-rb5000.rod_exposed":0.324,"kynshot-rb5000.screw_sink":0.02,"kynshot-rb5000.screw_socket":0.05,"kynshot-rb5000.screw_socket_depth":0.03,"kynshot-rb5000.weight":4.2,"std.density.steel":4.565,"std.receiver_extension.bore_d":1},"profiles":{},"bounds":{"min":[0,-0.4755,-0.4755],"max":[3.649,0.4485,0.4755]},"volume_in3":1.2891,"centroid":[1.808,0,0.0002],"shell":[1.6465,0,0.0017],"area_in2":10.9298,"triangles":11620,"manifold":true,"slabs":[[0,-0.475,-0.475,0.365,0.449,0.475],[0.365,-0.368,-0.368,3.649,0.368,0.368]],"slots":["body","screw","rod","seal","bumper"]},"kynshot-rb5000hp":{"part":"kynshot-rb5000hp","model":"kynshot-rb5000hp.glb","script":"kynshot_rb5000.py","inputs":{"kynshot-rb5000hp.body_front_chamfer":0.03,"kynshot-rb5000hp.body_length":2.68,"kynshot-rb5000hp.body_rear_chamfer":0.03,"kynshot-rb5000hp.bumper_d":0.7,"kynshot-rb5000hp.bumper_end_d":0.557,"kynshot-rb5000hp.bumper_exposed":0.299,"kynshot-rb5000hp.bumper_round":0.05,"kynshot-rb5000hp.head_back_d":0.82,"kynshot-rb5000hp.head_d":0.982,"kynshot-rb5000hp.head_flat_across":0.945,"kynshot-rb5000hp.head_flats":3,"kynshot-rb5000hp.head_front_chamfer":0.02,"kynshot-rb5000hp.head_rim":0.205,"kynshot-rb5000hp.head_thickness":0.238,"kynshot-rb5000hp.hub_chamfer":0.03,"kynshot-rb5000hp.hub_d":0.768,"kynshot-rb5000hp.hub_hole_d":0.1,"kynshot-rb5000hp.hub_length":0.141,"kynshot-rb5000hp.length":3.69,"kynshot-rb5000hp.mouth_depth":0.06,"kynshot-rb5000hp.mouth_wall":0.04,"kynshot-rb5000hp.od":0.76,"kynshot-rb5000hp.rod_d":0.194,"kynshot-rb5000hp.rod_exposed":0.332,"kynshot-rb5000hp.screw_sink":0.02,"kynshot-rb5000hp.screw_socket":0.05,"kynshot-rb5000hp.screw_socket_depth":0.03,"kynshot-rb5000hp.weight":4.8,"std.density.steel":4.565,"std.receiver_extension.bore_d":1},"profiles":{},"bounds":{"min":[0,-0.491,-0.491],"max":[3.69,0.454,0.491]},"volume_in3":1.5324,"centroid":[1.8545,0,0.0002],"shell":[1.666,0,0.0018],"area_in2":12.1413,"triangles":11584,"manifold":true,"slabs":[[0,-0.491,-0.491,0.369,0.454,0.491],[0.369,-0.38,-0.38,3.69,0.38,0.38]],"slots":["body","screw","rod","seal","bumper"]},"larue-mbt-2s":{"part":"larue-mbt-2s","model":"larue-mbt-2s.glb","script":"larue_mbt_2s.py","inputs":{"larue-mbt-2s.body_width":0.3,"larue-mbt-2s.boss_d":0.285,"larue-mbt-2s.boss_length":0.68,"larue-mbt-2s.pin_diameter":0.154,"larue-mbt-2s.shoe_chamfer":0.03,"larue-mbt-2s.shoe_width":0.305,"std.ar15.fcg_pocket_width":0.69,"std.ar15.trigger_slot_width":0.312},"profiles":{"side":[[-1.161,-0.126],[-1.154,-0.252],[-1.09,-0.283],[-1.005,-0.26],[-0.052,-0.258],[-0.049,-0.475],[-0.108,-0.755],[-0.101,-0.969],[-0.009,-1.278],[0.053,-1.387],[0.098,-1.399],[0.132,-1.364],[0.116,-0.554],[0.233,-0.411],[0.462,-0.344],[0.462,-0.288],[0.508,-0.271],[0.462,-0.232],[0.463,-0.151],[0.718,-0.133],[0.738,0.071],[0.404,0.076],[0.328,0.102],[0.271,0.186],[0.264,0.367],[0.182,0.509],[0.131,0.527],[0.04,0.4],[0.042,0.362],[0.126,0.354],[0.119,0.259],[0.065,0.168],[-0.363,0.191],[-0.374,0.252],[-0.335,0.282],[-0.318,0.354],[-0.341,0.466],[-0.416,0.497],[-0.47,0.453],[-0.496,0.242],[-0.527,0.208],[-0.705,0.224],[-0.735,0.333],[-0.857,0.333],[-0.885,0.068],[-0.922,0.033],[-1.146,0.02]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{}}},"bounds":{"min":[-1.161,-1.399,-0.34],"max":[0.738,0.527,0.34]},"volume_in3":0.341,"centroid":[-0.1671,-0.1597,0],"shell":[-0.1416,-0.1534,0],"area_in2":5.2003,"triangles":1106,"manifold":true,"slabs":[[-0.108,-1.399,-0.153,0.132,-0.629,0.153],[-1.154,-0.629,-0.153,0.508,-0.243,0.153],[-1.161,-0.243,-0.34,0.738,0.142,0.34],[-0.877,0.142,-0.34,0.301,0.527,0.34]],"slots":["shoe"]},"law-tactical-gen-s-folder.carrier_extension":{"part":"law-tactical-gen-s-folder","component":"carrier_extension","model":"law-tactical-gen-s-folder.carrier_extension.glb","script":"law_tactical_gen_s_folder.py","inputs":{"law-tactical-gen-s-folder.added_length":1.3,"law-tactical-gen-s-folder.body_top_above_axis":0.706,"law-tactical-gen-s-folder.bolt_counterbore_d":0.34,"law-tactical-gen-s-folder.bolt_head_d":0.3,"law-tactical-gen-s-folder.bolt_head_height":0.15,"law-tactical-gen-s-folder.bolt_head_recess":0.02,"law-tactical-gen-s-folder.bolt_socket":0.125,"law-tactical-gen-s-folder.bolt_socket_depth":0.08,"law-tactical-gen-s-folder.bore_thread_crest_d":1.1568,"law-tactical-gen-s-folder.button_below_axis":0.926,"law-tactical-gen-s-folder.button_proud":0.205,"law-tactical-gen-s-folder.button_side":0.751,"law-tactical-gen-s-folder.button_width":0.278,"law-tactical-gen-s-folder.ext_body_d":0.692,"law-tactical-gen-s-folder.ext_body_length":0.217,"law-tactical-gen-s-folder.ext_collar_d":0.689,"law-tactical-gen-s-folder.ext_collar_length":0.083,"law-tactical-gen-s-folder.ext_flare_d":0.652,"law-tactical-gen-s-folder.ext_flare_length":0.217,"law-tactical-gen-s-folder.ext_head_d":0.614,"law-tactical-gen-s-folder.ext_head_length":0.123,"law-tactical-gen-s-folder.ext_neck_d":0.452,"law-tactical-gen-s-folder.ext_neck_length":0.233,"law-tactical-gen-s-folder.ext_pilot_d":0.572,"law-tactical-gen-s-folder.ext_pilot_length":0.453,"law-tactical-gen-s-folder.ext_stem_d":0.467,"law-tactical-gen-s-folder.ext_stem_length":0.427,"law-tactical-gen-s-folder.flange_head_d":1.25,"law-tactical-gen-s-folder.flange_head_length":0.12,"law-tactical-gen-s-folder.hinge_x":1.775,"law-tactical-gen-s-folder.hinge_z":1.082,"law-tactical-gen-s-folder.knuckle_d":0.44,"law-tactical-gen-s-folder.length":1.3,"law-tactical-gen-s-folder.lower_tab_bottom":1.294,"law-tactical-gen-s-folder.lower_tab_top":1.107,"law-tactical-gen-s-folder.nut_bottom":1.476,"law-tactical-gen-s-folder.nut_d":0.369,"law-tactical-gen-s-folder.pivot_bottom":0.987,"law-tactical-gen-s-folder.pivot_d":0.6,"law-tactical-gen-s-folder.pivot_top":0.556,"law-tactical-gen-s-folder.qd_depth":0.45,"law-tactical-gen-s-folder.receiver_bore_d":1.207,"law-tactical-gen-s-folder.receiver_half_length":0.65,"law-tactical-gen-s-folder.stock_hole_big_below_axis":1.06,"law-tactical-gen-s-folder.stock_hole_big_d":0.5,"law-tactical-gen-s-folder.stock_hole_depth":0.35,"law-tactical-gen-s-folder.stock_hole_small_apart":0.366,"law-tactical-gen-s-folder.stock_hole_small_below_axis":0.685,"law-tactical-gen-s-folder.stock_hole_small_d":0.293,"law-tactical-gen-s-folder.tab_centre_below_axis":0.946,"law-tactical-gen-s-folder.tab_centre_out":0.299,"law-tactical-gen-s-folder.tab_height":0.557,"law-tactical-gen-s-folder.tab_proud":0.12,"law-tactical-gen-s-folder.tab_width":0.21,"law-tactical-gen-s-folder.upper_tab_bottom":0.434,"law-tactical-gen-s-folder.upper_tab_top":0.161,"law-tactical-gen-s-folder.washer_d":0.57,"law-tactical-gen-s-folder.window_centre_below_axis":0.971,"law-tactical-gen-s-folder.window_centre_out":0.342,"law-tactical-gen-s-folder.window_depth":0.3,"law-tactical-gen-s-folder.window_height":0.564,"law-tactical-gen-s-folder.window_width":0.42,"law-tactical-gen-s-folder.window_width_bottom":0.365,"law-tactical-gen-s-folder.window_width_top":0.449,"std.ar15.receiver_rear_x":-1.125,"std.ar15.upper_rear_face_x":-0.621,"std.receiver_extension.bore_d":1,"std.receiver_extension.front_face_x":-0.669,"std.receiver_extension.thread_major_d":1.1813,"std.receiver_extension.thread_minor_d":1.1093,"std.receiver_extension.thread_pitch":0.0625},"profiles":{"end_receiver":[[-0.5206,0.5126],[-0.4378,0.5715],[-0.3255,0.6291],[-0.1374,0.6782],[-0.0055,0.6866],[0.104,0.681],[0.2093,0.6628],[0.33,0.6221],[0.4114,0.5799],[0.5082,0.5112],[0.5882,0.434],[0.657,0.3441],[0.7272,0.2052],[0.7356,0.1098],[0.7496,0.0971],[0.7637,0.0087],[0.7931,-0.0376],[0.8367,-0.0811],[0.831,-0.0867],[0.8423,-0.1092],[0.8451,-0.1752],[0.8675,-0.1808],[0.8928,-0.1695],[1.0809,-0.1611],[1.0809,-1.2896],[0.904,-1.2896],[0.8409,-1.2798],[0.824,-1.2615],[0.7875,-1.2741],[0.4198,-1.2812],[0.3594,-1.2938],[0.3216,-1.3148],[0.2893,-1.3485],[0.2696,-1.3934],[0.2584,-1.4861],[0.2275,-1.5141],[-0.1893,-1.5198],[-0.2188,-1.4987],[-0.2497,-1.437],[-0.2862,-1.3977],[-0.3339,-1.3696],[-0.4027,-1.3471],[-0.435,-1.3191],[-0.4855,-1.2461],[-0.5318,-1.152],[-0.5922,-1.1085],[-0.6736,-1.0889],[-0.7185,-1.058],[-0.7508,-1.0552],[-0.7508,-0.7815],[-0.7437,-0.7604],[-0.7522,-0.3674],[-0.7943,-0.1555],[-0.7901,0.034],[-0.7592,0.1645],[-0.6946,0.3077],[-0.623,0.4101]],"end_stock":[[-0.5161,0.5392],[-0.641,0.4129],[-0.728,0.2726],[-0.7842,0.1126],[-0.8038,-0.0601],[-0.7842,-0.2299],[-0.5891,-0.9555],[-0.5568,-1.1394],[-0.5245,-1.2208],[-0.4754,-1.298],[-0.4291,-1.3317],[-0.342,-1.3598],[-0.2677,-1.4103],[-0.0136,-1.4327],[0.1913,-1.4103],[0.2236,-1.3906],[0.2881,-1.3148],[0.3611,-1.2868],[0.8804,-1.2896],[1.0812,-1.2896],[1.0812,-0.1611],[0.8945,-0.1569],[0.8369,-0.1288],[0.7934,-0.0867],[0.7752,-0.0587],[0.7541,0.0101],[0.7471,0.201],[0.6952,0.3203],[0.6404,0.4031],[0.5366,0.514],[0.3976,0.6122],[0.2573,0.6712],[0.1071,0.7021],[-0.0712,0.7063],[-0.2396,0.6796],[-0.3827,0.6249]]},"features":{"end_receiver":{},"end_stock":{}},"placement":{"end_receiver":{"plane":"zy","offset":{}},"end_stock":{"plane":"zy","offset":{}}},"bounds":{"min":[0.168,-0.346,-0.346],"max":[1.921,0.346,0.346]},"volume_in3":0.4201,"centroid":[1.0099,0,0],"shell":[1.0339,0,0],"area_in2":4.1342,"triangles":6144,"manifold":true,"slabs":[[0.168,-0.286,-0.286,0.519,0.286,0.286],[0.519,-0.346,-0.346,1.921,0.346,0.346]],"slots":["hardware"]},"law-tactical-gen-s-folder.receiver_half":{"part":"law-tactical-gen-s-folder","component":"receiver_half","model":"law-tactical-gen-s-folder.receiver_half.glb","script":"law_tactical_gen_s_folder.py","inputs":{"law-tactical-gen-s-folder.added_length":1.3,"law-tactical-gen-s-folder.button_below_axis":0.926,"law-tactical-gen-s-folder.button_proud":0.205,"law-tactical-gen-s-folder.button_side":0.751,"law-tactical-gen-s-folder.button_width":0.278,"law-tactical-gen-s-folder.flange_head_d":1.25,"law-tactical-gen-s-folder.flange_head_length":0.12,"law-tactical-gen-s-folder.hinge_x":1.775,"law-tactical-gen-s-folder.hinge_z":1.082,"law-tactical-gen-s-folder.knuckle_d":0.44,"law-tactical-gen-s-folder.length":1.3,"law-tactical-gen-s-folder.lower_tab_bottom":1.294,"law-tactical-gen-s-folder.lower_tab_top":1.107,"law-tactical-gen-s-folder.nut_bottom":1.476,"law-tactical-gen-s-folder.nut_d":0.369,"law-tactical-gen-s-folder.pivot_bottom":0.987,"law-tactical-gen-s-folder.pivot_d":0.6,"law-tactical-gen-s-folder.pivot_top":0.556,"law-tactical-gen-s-folder.receiver_bore_d":1.207,"law-tactical-gen-s-folder.receiver_half_length":0.65,"law-tactical-gen-s-folder.tab_centre_below_axis":0.946,"law-tactical-gen-s-folder.tab_centre_out":0.299,"law-tactical-gen-s-folder.tab_height":0.557,"law-tactical-gen-s-folder.tab_width":0.21,"law-tactical-gen-s-folder.upper_tab_bottom":0.434,"law-tactical-gen-s-folder.upper_tab_top":0.161,"law-tactical-gen-s-folder.washer_d":0.57,"law-tactical-gen-s-folder.window_centre_below_axis":0.971,"law-tactical-gen-s-folder.window_centre_out":0.342,"law-tactical-gen-s-folder.window_depth":0.3,"law-tactical-gen-s-folder.window_height":0.564,"law-tactical-gen-s-folder.window_width":0.42,"law-tactical-gen-s-folder.window_width_bottom":0.365,"law-tactical-gen-s-folder.window_width_top":0.449,"std.ar15.receiver_rear_x":-1.125,"std.receiver_extension.bore_d":1,"std.receiver_extension.front_face_x":-0.669,"std.receiver_extension.thread_major_d":1.1813,"std.receiver_extension.thread_minor_d":1.1093,"std.receiver_extension.thread_pitch":0.0625},"profiles":{"end_receiver":[[-0.5206,0.5126],[-0.4378,0.5715],[-0.3255,0.6291],[-0.1374,0.6782],[-0.0055,0.6866],[0.104,0.681],[0.2093,0.6628],[0.33,0.6221],[0.4114,0.5799],[0.5082,0.5112],[0.5882,0.434],[0.657,0.3441],[0.7272,0.2052],[0.7356,0.1098],[0.7496,0.0971],[0.7637,0.0087],[0.7931,-0.0376],[0.8367,-0.0811],[0.831,-0.0867],[0.8423,-0.1092],[0.8451,-0.1752],[0.8675,-0.1808],[0.8928,-0.1695],[1.0809,-0.1611],[1.0809,-1.2896],[0.904,-1.2896],[0.8409,-1.2798],[0.824,-1.2615],[0.7875,-1.2741],[0.4198,-1.2812],[0.3594,-1.2938],[0.3216,-1.3148],[0.2893,-1.3485],[0.2696,-1.3934],[0.2584,-1.4861],[0.2275,-1.5141],[-0.1893,-1.5198],[-0.2188,-1.4987],[-0.2497,-1.437],[-0.2862,-1.3977],[-0.3339,-1.3696],[-0.4027,-1.3471],[-0.435,-1.3191],[-0.4855,-1.2461],[-0.5318,-1.152],[-0.5922,-1.1085],[-0.6736,-1.0889],[-0.7185,-1.058],[-0.7508,-1.0552],[-0.7508,-0.7815],[-0.7437,-0.7604],[-0.7522,-0.3674],[-0.7943,-0.1555],[-0.7901,0.034],[-0.7592,0.1645],[-0.6946,0.3077],[-0.623,0.4101]],"end_stock":[[-0.5161,0.5392],[-0.641,0.4129],[-0.728,0.2726],[-0.7842,0.1126],[-0.8038,-0.0601],[-0.7842,-0.2299],[-0.5891,-0.9555],[-0.5568,-1.1394],[-0.5245,-1.2208],[-0.4754,-1.298],[-0.4291,-1.3317],[-0.342,-1.3598],[-0.2677,-1.4103],[-0.0136,-1.4327],[0.1913,-1.4103],[0.2236,-1.3906],[0.2881,-1.3148],[0.3611,-1.2868],[0.8804,-1.2896],[1.0812,-1.2896],[1.0812,-0.1611],[0.8945,-0.1569],[0.8369,-0.1288],[0.7934,-0.0867],[0.7752,-0.0587],[0.7541,0.0101],[0.7471,0.201],[0.6952,0.3203],[0.6404,0.4031],[0.5366,0.514],[0.3976,0.6122],[0.2573,0.6712],[0.1071,0.7021],[-0.0712,0.7063],[-0.2396,0.6796],[-0.3827,0.6249]]},"features":{"end_receiver":{},"end_stock":{}},"placement":{"end_receiver":{"plane":"zy","offset":{}},"end_stock":{"plane":"zy","offset":{}}},"bounds":{"min":[0.669,-1.5198,-0.956],"max":[2.075,0.6866,1.382]},"volume_in3":1.5959,"centroid":[1.439,-0.5524,0.1753],"shell":[1.3944,-0.3033,0.1189],"area_in2":24.1375,"triangles":28842,"manifold":true,"slabs":[[0.726,-1.127,-0.956,1.775,0.467,-0.566],[0.669,-1.52,-0.566,1.775,0.687,0.603],[1.125,-1.278,0.603,2.061,0.415,0.992],[1.125,-1.107,0.992,2.075,-0.434,1.382]],"slots":["body","hardware"]},"law-tactical-gen-s-folder.stock_half":{"part":"law-tactical-gen-s-folder","component":"stock_half","model":"law-tactical-gen-s-folder.stock_half.glb","script":"law_tactical_gen_s_folder.py","inputs":{"law-tactical-gen-s-folder.added_length":1.3,"law-tactical-gen-s-folder.body_top_above_axis":0.706,"law-tactical-gen-s-folder.bolt_counterbore_d":0.34,"law-tactical-gen-s-folder.bolt_head_d":0.3,"law-tactical-gen-s-folder.bolt_head_height":0.15,"law-tactical-gen-s-folder.bolt_head_recess":0.02,"law-tactical-gen-s-folder.bolt_socket":0.125,"law-tactical-gen-s-folder.bolt_socket_depth":0.08,"law-tactical-gen-s-folder.bore_thread_crest_d":1.1568,"law-tactical-gen-s-folder.button_below_axis":0.926,"law-tactical-gen-s-folder.button_proud":0.205,"law-tactical-gen-s-folder.button_side":0.751,"law-tactical-gen-s-folder.button_width":0.278,"law-tactical-gen-s-folder.flange_head_d":1.25,"law-tactical-gen-s-folder.flange_head_length":0.12,"law-tactical-gen-s-folder.hinge_x":1.775,"law-tactical-gen-s-folder.hinge_z":1.082,"law-tactical-gen-s-folder.knuckle_d":0.44,"law-tactical-gen-s-folder.length":1.3,"law-tactical-gen-s-folder.lower_tab_bottom":1.294,"law-tactical-gen-s-folder.lower_tab_top":1.107,"law-tactical-gen-s-folder.nut_bottom":1.476,"law-tactical-gen-s-folder.nut_d":0.369,"law-tactical-gen-s-folder.pivot_bottom":0.987,"law-tactical-gen-s-folder.pivot_d":0.6,"law-tactical-gen-s-folder.pivot_top":0.556,"law-tactical-gen-s-folder.qd_depth":0.45,"law-tactical-gen-s-folder.receiver_bore_d":1.207,"law-tactical-gen-s-folder.receiver_half_length":0.65,"law-tactical-gen-s-folder.stock_hole_big_below_axis":1.06,"law-tactical-gen-s-folder.stock_hole_big_d":0.5,"law-tactical-gen-s-folder.stock_hole_depth":0.35,"law-tactical-gen-s-folder.stock_hole_small_apart":0.366,"law-tactical-gen-s-folder.stock_hole_small_below_axis":0.685,"law-tactical-gen-s-folder.stock_hole_small_d":0.293,"law-tactical-gen-s-folder.tab_centre_below_axis":0.946,"law-tactical-gen-s-folder.tab_centre_out":0.299,"law-tactical-gen-s-folder.tab_height":0.557,"law-tactical-gen-s-folder.tab_proud":0.12,"law-tactical-gen-s-folder.tab_width":0.21,"law-tactical-gen-s-folder.upper_tab_bottom":0.434,"law-tactical-gen-s-folder.upper_tab_top":0.161,"law-tactical-gen-s-folder.washer_d":0.57,"law-tactical-gen-s-folder.window_centre_below_axis":0.971,"law-tactical-gen-s-folder.window_centre_out":0.342,"law-tactical-gen-s-folder.window_depth":0.3,"law-tactical-gen-s-folder.window_height":0.564,"law-tactical-gen-s-folder.window_width":0.42,"law-tactical-gen-s-folder.window_width_bottom":0.365,"law-tactical-gen-s-folder.window_width_top":0.449,"std.ar15.receiver_rear_x":-1.125,"std.receiver_extension.bore_d":1,"std.receiver_extension.front_face_x":-0.669,"std.receiver_extension.thread_major_d":1.1813,"std.receiver_extension.thread_minor_d":1.1093,"std.receiver_extension.thread_pitch":0.0625},"profiles":{"end_receiver":[[-0.5206,0.5126],[-0.4378,0.5715],[-0.3255,0.6291],[-0.1374,0.6782],[-0.0055,0.6866],[0.104,0.681],[0.2093,0.6628],[0.33,0.6221],[0.4114,0.5799],[0.5082,0.5112],[0.5882,0.434],[0.657,0.3441],[0.7272,0.2052],[0.7356,0.1098],[0.7496,0.0971],[0.7637,0.0087],[0.7931,-0.0376],[0.8367,-0.0811],[0.831,-0.0867],[0.8423,-0.1092],[0.8451,-0.1752],[0.8675,-0.1808],[0.8928,-0.1695],[1.0809,-0.1611],[1.0809,-1.2896],[0.904,-1.2896],[0.8409,-1.2798],[0.824,-1.2615],[0.7875,-1.2741],[0.4198,-1.2812],[0.3594,-1.2938],[0.3216,-1.3148],[0.2893,-1.3485],[0.2696,-1.3934],[0.2584,-1.4861],[0.2275,-1.5141],[-0.1893,-1.5198],[-0.2188,-1.4987],[-0.2497,-1.437],[-0.2862,-1.3977],[-0.3339,-1.3696],[-0.4027,-1.3471],[-0.435,-1.3191],[-0.4855,-1.2461],[-0.5318,-1.152],[-0.5922,-1.1085],[-0.6736,-1.0889],[-0.7185,-1.058],[-0.7508,-1.0552],[-0.7508,-0.7815],[-0.7437,-0.7604],[-0.7522,-0.3674],[-0.7943,-0.1555],[-0.7901,0.034],[-0.7592,0.1645],[-0.6946,0.3077],[-0.623,0.4101]],"end_stock":[[-0.5161,0.5392],[-0.641,0.4129],[-0.728,0.2726],[-0.7842,0.1126],[-0.8038,-0.0601],[-0.7842,-0.2299],[-0.5891,-0.9555],[-0.5568,-1.1394],[-0.5245,-1.2208],[-0.4754,-1.298],[-0.4291,-1.3317],[-0.342,-1.3598],[-0.2677,-1.4103],[-0.0136,-1.4327],[0.1913,-1.4103],[0.2236,-1.3906],[0.2881,-1.3148],[0.3611,-1.2868],[0.8804,-1.2896],[1.0812,-1.2896],[1.0812,-0.1611],[0.8945,-0.1569],[0.8369,-0.1288],[0.7934,-0.0867],[0.7752,-0.0587],[0.7541,0.0101],[0.7471,0.201],[0.6952,0.3203],[0.6404,0.4031],[0.5366,0.514],[0.3976,0.6122],[0.2573,0.6712],[0.1071,0.7021],[-0.0712,0.7063],[-0.2396,0.6796],[-0.3827,0.6249]]},"features":{"end_receiver":{},"end_stock":{}},"placement":{"end_receiver":{"plane":"zy","offset":{}},"end_stock":{"plane":"zy","offset":{}}},"bounds":{"min":[1.555,-1.476,-0.8038],"max":[2.425,0.7063,1.302]},"volume_in3":1.1643,"centroid":[2.0615,-0.5699,0.1796],"shell":[2.0561,-0.4815,0.2211],"area_in2":14.5464,"triangles":19358,"manifold":true,"slabs":[[1.555,-1.476,-0.562,2.425,-1.112,1.302],[1.555,-1.112,-0.645,2.425,-0.749,1.302],[1.555,-0.749,-0.743,2.425,-0.385,1.302],[1.555,-0.385,-0.804,2.425,-0.021,1.302],[1.775,-0.021,-0.799,2.425,0.343,0.764],[1.775,0.343,-0.685,2.425,0.706,0.68]],"slots":["body","hardware"]},"law-tactical-gen3m-folder.carrier_extension":{"part":"law-tactical-gen3m-folder","component":"carrier_extension","model":"law-tactical-gen3m-folder.carrier_extension.glb","script":"law_tactical_gen3m_folder.py","inputs":{"law-tactical-gen3m-folder.added_length":1.3,"law-tactical-gen3m-folder.body_top_above_axis":0.734,"law-tactical-gen3m-folder.bolt_counterbore_d":0.374,"law-tactical-gen3m-folder.bolt_head_d":0.317,"law-tactical-gen3m-folder.bolt_head_height":0.15,"law-tactical-gen3m-folder.bolt_head_recess":0.04,"law-tactical-gen3m-folder.bolt_socket":0.125,"law-tactical-gen3m-folder.bolt_socket_depth":0.08,"law-tactical-gen3m-folder.bore_thread_crest_d":1.1515,"law-tactical-gen3m-folder.button_below_axis":0.9,"law-tactical-gen3m-folder.button_proud":0.18,"law-tactical-gen3m-folder.button_width":0.29,"law-tactical-gen3m-folder.ext_body_d":0.714,"law-tactical-gen3m-folder.ext_body_length":0.25,"law-tactical-gen3m-folder.ext_collar_d":0.712,"law-tactical-gen3m-folder.ext_collar_length":0.093,"law-tactical-gen3m-folder.ext_flare_length":0.206,"law-tactical-gen3m-folder.ext_head_d":0.623,"law-tactical-gen3m-folder.ext_head_length":0.161,"law-tactical-gen3m-folder.ext_neck_d":0.468,"law-tactical-gen3m-folder.ext_neck_length":0.206,"law-tactical-gen3m-folder.ext_pilot_d":0.599,"law-tactical-gen3m-folder.ext_pilot_length":0.466,"law-tactical-gen3m-folder.ext_stem_d":0.48,"law-tactical-gen3m-folder.ext_stem_length":0.383,"law-tactical-gen3m-folder.far_side":0.79,"law-tactical-gen3m-folder.flange_head_d":1.3,"law-tactical-gen3m-folder.flange_head_length":0.12,"law-tactical-gen3m-folder.hinge_x":1.775,"law-tactical-gen3m-folder.hinge_z":1.137,"law-tactical-gen3m-folder.knuckle_d":0.481,"law-tactical-gen3m-folder.length":1.3,"law-tactical-gen3m-folder.lower_tab_bottom":1.284,"law-tactical-gen3m-folder.lower_tab_top":1.1,"law-tactical-gen3m-folder.nut_bottom":1.511,"law-tactical-gen3m-folder.nut_d":0.36,"law-tactical-gen3m-folder.pivot_bottom":0.968,"law-tactical-gen3m-folder.pivot_d":0.63,"law-tactical-gen3m-folder.pivot_top":0.542,"law-tactical-gen3m-folder.receiver_bore_d":1.213,"law-tactical-gen3m-folder.receiver_half_length":0.65,"law-tactical-gen3m-folder.stock_hole_big_below_axis":1.13,"law-tactical-gen3m-folder.stock_hole_big_d":0.44,"law-tactical-gen3m-folder.stock_hole_depth":0.4,"law-tactical-gen3m-folder.stock_hole_small_apart":0.33,"law-tactical-gen3m-folder.stock_hole_small_below_axis":0.69,"law-tactical-gen3m-folder.stock_hole_small_d":0.22,"law-tactical-gen3m-folder.tab_centre_below_axis":0.887,"law-tactical-gen3m-folder.tab_centre_out":0.327,"law-tactical-gen3m-folder.tab_height":0.4,"law-tactical-gen3m-folder.tab_proud":0.15,"law-tactical-gen3m-folder.tab_width":0.22,"law-tactical-gen3m-folder.upper_tab_bottom":0.409,"law-tactical-gen3m-folder.upper_tab_top":0.061,"law-tactical-gen3m-folder.washer_d":0.527,"law-tactical-gen3m-folder.window_depth":0.3,"law-tactical-gen3m-folder.window_height":0.45,"law-tactical-gen3m-folder.window_width":0.36,"std.ar15.receiver_rear_x":-1.125,"std.ar15.upper_rear_face_x":-0.621,"std.receiver_extension.bore_d":1,"std.receiver_extension.front_face_x":-0.669,"std.receiver_extension.thread_major_d":1.1813,"std.receiver_extension.thread_minor_d":1.1093,"std.receiver_extension.thread_pitch":0.0625},"profiles":{"end_receiver":[[0.1793,0.7277],[0.2974,0.7047],[0.424,0.6587],[0.5565,0.5781],[0.663,0.4802],[0.7493,0.3679],[0.8012,0.27],[0.8184,0.2211],[0.8271,0.1117],[0.8443,0.0541],[0.9249,-0.0495],[0.9451,-0.0639],[1.0343,-0.0582],[1.043,-0.0495],[1.0545,-0.0582],[1.1351,-0.0553],[1.1351,-1.2903],[1.0343,-1.2874],[0.9768,-1.2874],[0.9019,-1.2787],[0.8127,-1.2903],[0.4528,-1.2903],[0.3924,-1.3104],[0.3521,-1.3478],[0.329,-1.391],[0.3146,-1.4946],[0.2743,-1.5292],[-0.1402,-1.5321],[-0.2381,-1.5033],[-0.264,-1.4716],[-0.2956,-1.4025],[-0.3475,-1.3565],[-0.5317,-1.3536],[-0.6526,-1.319],[-0.6987,-1.2759],[-0.7361,-1.2125],[-0.7476,-1.1521],[-0.7476,-1.0628],[-0.79,-1.04],[-0.7908,0.0455],[-0.762,0.1837],[-0.6958,0.3334],[-0.5864,0.4802],[-0.4914,0.5608],[-0.3964,0.6212],[-0.3763,0.6155],[-0.3417,0.6414],[-0.2525,0.6817],[-0.1143,0.722],[-0.0049,0.7335]],"end_stock":[[-0.5331,0.5176],[-0.6483,0.3852],[-0.7001,0.2988],[-0.7404,0.2067],[-0.7778,0.0628],[-0.7865,-0.1128],[-0.7519,-0.3086],[-0.5619,-0.9765],[-0.536,-1.1406],[-0.4957,-1.2413],[-0.4381,-1.3248],[-0.4036,-1.3478],[-0.3431,-1.3651],[-0.3086,-1.3853],[-0.2654,-1.4342],[-0.2424,-1.5004],[-0.2078,-1.5263],[0.2009,-1.5321],[0.3017,-1.5148],[0.319,-1.5033],[0.3391,-1.4745],[0.3564,-1.3363],[0.4024,-1.2931],[0.912,-1.2903],[0.9667,-1.2931],[1.1365,-1.2903],[1.1365,-0.0553],[1.1164,-0.0438],[1.1077,-0.0524],[0.984,-0.0438],[0.9724,-0.0553],[0.9206,-0.0553],[0.8659,-0.0438],[0.8199,-0.0092],[0.817,0.0714],[0.794,0.1837],[0.7594,0.2758],[0.7047,0.3823],[0.6068,0.4917],[0.5176,0.5637],[0.4284,0.6126],[0.2844,0.6731],[0.1635,0.7018],[0.0599,0.7134],[-0.0725,0.7134],[-0.1762,0.699],[-0.2712,0.6731],[-0.3892,0.6212]]},"features":{"end_receiver":{},"end_stock":{}},"placement":{"end_receiver":{"plane":"zy","offset":{}},"end_stock":{"plane":"zy","offset":{}}},"bounds":{"min":[0.155,-0.357,-0.357],"max":[1.92,0.357,0.357]},"volume_in3":0.4689,"centroid":[1.0003,0,0],"shell":[1.0216,0,0],"area_in2":4.3623,"triangles":5184,"manifold":true,"slabs":[[0.155,-0.299,-0.299,0.508,0.299,0.299],[0.508,-0.357,-0.357,1.92,0.357,0.357]],"slots":["hardware"]},"law-tactical-gen3m-folder.receiver_half":{"part":"law-tactical-gen3m-folder","component":"receiver_half","model":"law-tactical-gen3m-folder.receiver_half.glb","script":"law_tactical_gen3m_folder.py","inputs":{"law-tactical-gen3m-folder.added_length":1.3,"law-tactical-gen3m-folder.button_below_axis":0.9,"law-tactical-gen3m-folder.button_proud":0.18,"law-tactical-gen3m-folder.button_width":0.29,"law-tactical-gen3m-folder.far_side":0.79,"law-tactical-gen3m-folder.flange_head_d":1.3,"law-tactical-gen3m-folder.flange_head_length":0.12,"law-tactical-gen3m-folder.hinge_x":1.775,"law-tactical-gen3m-folder.hinge_z":1.137,"law-tactical-gen3m-folder.knuckle_d":0.481,"law-tactical-gen3m-folder.length":1.3,"law-tactical-gen3m-folder.lower_tab_bottom":1.284,"law-tactical-gen3m-folder.lower_tab_top":1.1,"law-tactical-gen3m-folder.nut_bottom":1.511,"law-tactical-gen3m-folder.nut_d":0.36,"law-tactical-gen3m-folder.pivot_bottom":0.968,"law-tactical-gen3m-folder.pivot_d":0.63,"law-tactical-gen3m-folder.pivot_top":0.542,"law-tactical-gen3m-folder.receiver_bore_d":1.213,"law-tactical-gen3m-folder.receiver_half_length":0.65,"law-tactical-gen3m-folder.tab_centre_below_axis":0.887,"law-tactical-gen3m-folder.tab_centre_out":0.327,"law-tactical-gen3m-folder.tab_height":0.4,"law-tactical-gen3m-folder.tab_width":0.22,"law-tactical-gen3m-folder.upper_tab_bottom":0.409,"law-tactical-gen3m-folder.upper_tab_top":0.061,"law-tactical-gen3m-folder.washer_d":0.527,"law-tactical-gen3m-folder.window_depth":0.3,"law-tactical-gen3m-folder.window_height":0.45,"law-tactical-gen3m-folder.window_width":0.36,"std.ar15.receiver_rear_x":-1.125,"std.receiver_extension.bore_d":1,"std.receiver_extension.front_face_x":-0.669,"std.receiver_extension.thread_major_d":1.1813,"std.receiver_extension.thread_minor_d":1.1093,"std.receiver_extension.thread_pitch":0.0625},"profiles":{"end_receiver":[[0.1793,0.7277],[0.2974,0.7047],[0.424,0.6587],[0.5565,0.5781],[0.663,0.4802],[0.7493,0.3679],[0.8012,0.27],[0.8184,0.2211],[0.8271,0.1117],[0.8443,0.0541],[0.9249,-0.0495],[0.9451,-0.0639],[1.0343,-0.0582],[1.043,-0.0495],[1.0545,-0.0582],[1.1351,-0.0553],[1.1351,-1.2903],[1.0343,-1.2874],[0.9768,-1.2874],[0.9019,-1.2787],[0.8127,-1.2903],[0.4528,-1.2903],[0.3924,-1.3104],[0.3521,-1.3478],[0.329,-1.391],[0.3146,-1.4946],[0.2743,-1.5292],[-0.1402,-1.5321],[-0.2381,-1.5033],[-0.264,-1.4716],[-0.2956,-1.4025],[-0.3475,-1.3565],[-0.5317,-1.3536],[-0.6526,-1.319],[-0.6987,-1.2759],[-0.7361,-1.2125],[-0.7476,-1.1521],[-0.7476,-1.0628],[-0.79,-1.04],[-0.7908,0.0455],[-0.762,0.1837],[-0.6958,0.3334],[-0.5864,0.4802],[-0.4914,0.5608],[-0.3964,0.6212],[-0.3763,0.6155],[-0.3417,0.6414],[-0.2525,0.6817],[-0.1143,0.722],[-0.0049,0.7335]],"end_stock":[[-0.5331,0.5176],[-0.6483,0.3852],[-0.7001,0.2988],[-0.7404,0.2067],[-0.7778,0.0628],[-0.7865,-0.1128],[-0.7519,-0.3086],[-0.5619,-0.9765],[-0.536,-1.1406],[-0.4957,-1.2413],[-0.4381,-1.3248],[-0.4036,-1.3478],[-0.3431,-1.3651],[-0.3086,-1.3853],[-0.2654,-1.4342],[-0.2424,-1.5004],[-0.2078,-1.5263],[0.2009,-1.5321],[0.3017,-1.5148],[0.319,-1.5033],[0.3391,-1.4745],[0.3564,-1.3363],[0.4024,-1.2931],[0.912,-1.2903],[0.9667,-1.2931],[1.1365,-1.2903],[1.1365,-0.0553],[1.1164,-0.0438],[1.1077,-0.0524],[0.984,-0.0438],[0.9724,-0.0553],[0.9206,-0.0553],[0.8659,-0.0438],[0.8199,-0.0092],[0.817,0.0714],[0.794,0.1837],[0.7594,0.2758],[0.7047,0.3823],[0.6068,0.4917],[0.5176,0.5637],[0.4284,0.6126],[0.2844,0.6731],[0.1635,0.7018],[0.0599,0.7134],[-0.0725,0.7134],[-0.1762,0.699],[-0.2712,0.6731],[-0.3892,0.6212]]},"features":{"end_receiver":{},"end_stock":{}},"placement":{"end_receiver":{"plane":"zy","offset":{}},"end_stock":{"plane":"zy","offset":{}}},"bounds":{"min":[0.669,-1.5321,-0.97],"max":[2.09,0.7335,1.452]},"volume_in3":1.804,"centroid":[1.4437,-0.5417,0.1741],"shell":[1.3977,-0.2957,0.1256],"area_in2":25.0052,"triangles":28734,"manifold":true,"slabs":[[1.125,-1.327,-0.97,1.775,0.43,-0.624],[0.669,-1.441,-0.624,1.775,0.67,-0.278],[0.669,-1.532,-0.278,1.775,0.734,0.414],[0.669,-1.303,0.414,1.775,0.662,0.76],[1.125,-1.29,0.76,2.088,0.348,1.106],[1.125,-1.1,1.106,2.09,-0.409,1.452]],"slots":["body","hardware"]},"law-tactical-gen3m-folder.stock_half":{"part":"law-tactical-gen3m-folder","component":"stock_half","model":"law-tactical-gen3m-folder.stock_half.glb","script":"law_tactical_gen3m_folder.py","inputs":{"law-tactical-gen3m-folder.added_length":1.3,"law-tactical-gen3m-folder.body_top_above_axis":0.734,"law-tactical-gen3m-folder.bolt_counterbore_d":0.374,"law-tactical-gen3m-folder.bolt_head_d":0.317,"law-tactical-gen3m-folder.bolt_head_height":0.15,"law-tactical-gen3m-folder.bolt_head_recess":0.04,"law-tactical-gen3m-folder.bolt_socket":0.125,"law-tactical-gen3m-folder.bolt_socket_depth":0.08,"law-tactical-gen3m-folder.bore_thread_crest_d":1.1515,"law-tactical-gen3m-folder.button_below_axis":0.9,"law-tactical-gen3m-folder.button_proud":0.18,"law-tactical-gen3m-folder.button_width":0.29,"law-tactical-gen3m-folder.far_side":0.79,"law-tactical-gen3m-folder.flange_head_d":1.3,"law-tactical-gen3m-folder.flange_head_length":0.12,"law-tactical-gen3m-folder.hinge_x":1.775,"law-tactical-gen3m-folder.hinge_z":1.137,"law-tactical-gen3m-folder.knuckle_d":0.481,"law-tactical-gen3m-folder.length":1.3,"law-tactical-gen3m-folder.lower_tab_bottom":1.284,"law-tactical-gen3m-folder.lower_tab_top":1.1,"law-tactical-gen3m-folder.nut_bottom":1.511,"law-tactical-gen3m-folder.nut_d":0.36,"law-tactical-gen3m-folder.pivot_bottom":0.968,"law-tactical-gen3m-folder.pivot_d":0.63,"law-tactical-gen3m-folder.pivot_top":0.542,"law-tactical-gen3m-folder.receiver_bore_d":1.213,"law-tactical-gen3m-folder.receiver_half_length":0.65,"law-tactical-gen3m-folder.stock_hole_big_below_axis":1.13,"law-tactical-gen3m-folder.stock_hole_big_d":0.44,"law-tactical-gen3m-folder.stock_hole_depth":0.4,"law-tactical-gen3m-folder.stock_hole_small_apart":0.33,"law-tactical-gen3m-folder.stock_hole_small_below_axis":0.69,"law-tactical-gen3m-folder.stock_hole_small_d":0.22,"law-tactical-gen3m-folder.tab_centre_below_axis":0.887,"law-tactical-gen3m-folder.tab_centre_out":0.327,"law-tactical-gen3m-folder.tab_height":0.4,"law-tactical-gen3m-folder.tab_proud":0.15,"law-tactical-gen3m-folder.tab_width":0.22,"law-tactical-gen3m-folder.upper_tab_bottom":0.409,"law-tactical-gen3m-folder.upper_tab_top":0.061,"law-tactical-gen3m-folder.washer_d":0.527,"law-tactical-gen3m-folder.window_depth":0.3,"law-tactical-gen3m-folder.window_height":0.45,"law-tactical-gen3m-folder.window_width":0.36,"std.ar15.receiver_rear_x":-1.125,"std.receiver_extension.bore_d":1,"std.receiver_extension.front_face_x":-0.669,"std.receiver_extension.thread_major_d":1.1813,"std.receiver_extension.thread_minor_d":1.1093,"std.receiver_extension.thread_pitch":0.0625},"profiles":{"end_receiver":[[0.1793,0.7277],[0.2974,0.7047],[0.424,0.6587],[0.5565,0.5781],[0.663,0.4802],[0.7493,0.3679],[0.8012,0.27],[0.8184,0.2211],[0.8271,0.1117],[0.8443,0.0541],[0.9249,-0.0495],[0.9451,-0.0639],[1.0343,-0.0582],[1.043,-0.0495],[1.0545,-0.0582],[1.1351,-0.0553],[1.1351,-1.2903],[1.0343,-1.2874],[0.9768,-1.2874],[0.9019,-1.2787],[0.8127,-1.2903],[0.4528,-1.2903],[0.3924,-1.3104],[0.3521,-1.3478],[0.329,-1.391],[0.3146,-1.4946],[0.2743,-1.5292],[-0.1402,-1.5321],[-0.2381,-1.5033],[-0.264,-1.4716],[-0.2956,-1.4025],[-0.3475,-1.3565],[-0.5317,-1.3536],[-0.6526,-1.319],[-0.6987,-1.2759],[-0.7361,-1.2125],[-0.7476,-1.1521],[-0.7476,-1.0628],[-0.79,-1.04],[-0.7908,0.0455],[-0.762,0.1837],[-0.6958,0.3334],[-0.5864,0.4802],[-0.4914,0.5608],[-0.3964,0.6212],[-0.3763,0.6155],[-0.3417,0.6414],[-0.2525,0.6817],[-0.1143,0.722],[-0.0049,0.7335]],"end_stock":[[-0.5331,0.5176],[-0.6483,0.3852],[-0.7001,0.2988],[-0.7404,0.2067],[-0.7778,0.0628],[-0.7865,-0.1128],[-0.7519,-0.3086],[-0.5619,-0.9765],[-0.536,-1.1406],[-0.4957,-1.2413],[-0.4381,-1.3248],[-0.4036,-1.3478],[-0.3431,-1.3651],[-0.3086,-1.3853],[-0.2654,-1.4342],[-0.2424,-1.5004],[-0.2078,-1.5263],[0.2009,-1.5321],[0.3017,-1.5148],[0.319,-1.5033],[0.3391,-1.4745],[0.3564,-1.3363],[0.4024,-1.2931],[0.912,-1.2903],[0.9667,-1.2931],[1.1365,-1.2903],[1.1365,-0.0553],[1.1164,-0.0438],[1.1077,-0.0524],[0.984,-0.0438],[0.9724,-0.0553],[0.9206,-0.0553],[0.8659,-0.0438],[0.8199,-0.0092],[0.817,0.0714],[0.794,0.1837],[0.7594,0.2758],[0.7047,0.3823],[0.6068,0.4917],[0.5176,0.5637],[0.4284,0.6126],[0.2844,0.6731],[0.1635,0.7018],[0.0599,0.7134],[-0.0725,0.7134],[-0.1762,0.699],[-0.2712,0.6731],[-0.3892,0.6212]]},"features":{"end_receiver":{},"end_stock":{}},"placement":{"end_receiver":{"plane":"zy","offset":{}},"end_stock":{"plane":"zy","offset":{}}},"bounds":{"min":[1.5345,-1.5321,-0.7865],"max":[2.425,0.7134,1.3775]},"volume_in3":1.3413,"centroid":[2.0646,-0.5909,0.2381],"shell":[2.0521,-0.485,0.2706],"area_in2":15.2328,"triangles":19440,"manifold":true,"slabs":[[1.535,-1.532,-0.529,2.425,-1.158,1.377],[1.535,-1.158,-0.617,2.425,-0.784,1.377],[1.625,-0.784,-0.723,2.425,-0.409,0.812],[1.535,-0.409,-0.786,2.425,-0.035,1.377],[1.775,-0.035,-0.783,2.425,0.339,0.854],[1.775,0.339,-0.676,2.425,0.713,0.727]],"slots":["body","hardware"]},"magpul-ctr":{"part":"magpul-ctr","model":"magpul-ctr.glb","script":"magpul_ctr.py","inputs":{"bcm-receiver-extension.tube_front_behind_pin":0.669,"bcm-receiver-extension.tube_length":7.25,"magpul-ctr.bore_diameter":1.158,"magpul-ctr.butt_behind_pin_pos1":8.726,"magpul-ctr.frame_width":0.69,"magpul-ctr.rail_channel_floor_below_axis":0.874,"magpul-ctr.rail_channel_width":0.49,"magpul-ctr.tube_axis_below_top":0.72},"profiles":{"side":[[0,-0.342],[0,-0.787],[0.03,-0.954],[0.041,-1.142],[0.273,-2.448],[0.354,-3.055],[0.456,-3.977],[0.506,-4.726],[0.542,-5.01],[0.577,-5.086],[0.666,-5.169],[0.742,-5.189],[0.853,-5.184],[0.878,-5.215],[0.914,-5.225],[1.375,-5.215],[1.496,-5.179],[1.6,-5.086],[1.666,-4.919],[1.701,-4.878],[1.701,-4.858],[1.775,-4.784],[4.022,-3.215],[4.402,-2.967],[4.488,-2.987],[4.559,-2.942],[4.607,-2.898],[4.622,-2.853],[4.746,-2.744],[4.797,-2.729],[4.827,-2.688],[4.898,-2.658],[4.929,-2.618],[4.995,-2.592],[5.05,-2.536],[5.106,-2.516],[5.131,-2.481],[5.217,-2.44],[5.238,-2.405],[5.298,-2.385],[5.344,-2.334],[5.394,-2.319],[5.44,-2.268],[5.506,-2.243],[5.683,-2.121],[5.794,-2.081],[5.926,-2.071],[6.68,-2.081],[6.696,-2.071],[6.746,-2.106],[6.812,-2.106],[6.842,-2.091],[6.88,-2.023],[6.916,-1.734],[6.961,-0.985],[6.967,-0.57],[6.916,-0.119],[6.817,-0.056],[0.605,-0.051],[0.544,0],[0.397,0],[0.332,-0.056],[0.311,-0.046],[0.154,-0.066],[0.073,-0.086],[0.015,-0.134]],"front":[[-0.848,-1.009],[-0.699,-1.911],[-0.609,-2.994],[-0.59,-3.69],[-0.622,-4.702],[-0.603,-4.85],[-0.519,-5.024],[-0.4,-5.131],[-0.329,-5.169],[-0.142,-5.215],[0.161,-5.215],[0.348,-5.163],[0.451,-5.092],[0.577,-4.947],[0.616,-4.792],[0.609,-4.148],[0.596,-4.122],[0.603,-3.606],[0.59,-3.561],[0.603,-3.548],[0.596,-3.394],[0.609,-3.368],[0.603,-3.2],[0.616,-3.181],[0.622,-2.826],[0.641,-2.73],[0.648,-2.459],[0.661,-2.446],[0.654,-2.395],[0.674,-2.311],[0.706,-1.879],[0.738,-1.782],[0.77,-1.466],[0.802,-1.312],[0.796,-1.273],[0.835,-1.112],[0.848,-0.97],[0.815,-0.822],[0.68,-0.448],[0.564,-0.255],[0.425,-0.129],[0.322,-0.071],[0.18,-0.019],[0,-0.006],[-0.013,0],[-0.116,-0.006],[-0.335,-0.077],[-0.413,-0.122],[-0.545,-0.235],[-0.622,-0.338],[-0.667,-0.429],[-0.712,-0.57],[-0.777,-0.706]]},"features":{"side":{"through":[[[1.281,-1.111],[1.296,-1.071],[1.359,-1.028],[2.362,-1.028],[2.385,-1.051],[2.38,-1.091],[2.342,-1.139],[2.301,-1.154],[1.329,-1.154]],[[4.82,-1.091],[4.873,-1.023],[4.908,-1.013],[5.764,-1.018],[5.777,-1.03],[5.767,-1.096],[5.708,-1.144],[4.908,-1.144],[4.833,-1.139]],[[1.261,-2.018],[1.266,-1.957],[1.291,-1.901],[1.364,-1.833],[1.425,-1.813],[1.547,-1.833],[1.63,-1.926],[1.63,-1.987],[1.6,-2.063],[1.521,-2.131],[1.471,-2.147],[1.415,-2.147],[1.344,-2.121],[1.296,-2.078]],[[1.296,-2.605],[1.306,-2.488],[1.347,-2.418],[1.415,-2.349],[1.567,-2.319],[1.663,-2.263],[1.742,-2.169],[1.777,-2.053],[1.81,-2.015],[2.078,-1.792],[2.225,-1.732],[2.752,-1.726],[2.764,-1.739],[2.311,-1.929],[2.248,-1.977],[2.233,-2.012],[2.233,-2.068],[2.258,-2.149],[2.248,-2.159],[2.273,-2.205],[2.268,-2.245],[2.288,-2.286],[2.321,-2.309],[3.688,-1.919],[4.063,-1.894],[4.086,-1.871],[4.091,-1.825],[4.103,-1.813],[4.121,-1.825],[4.162,-1.906],[4.167,-2.038],[4.131,-2.134],[4.058,-2.223],[1.871,-3.959],[1.8,-4.01],[1.719,-4.04],[1.613,-4.035],[1.521,-3.99],[1.448,-3.901],[1.438,-3.845],[1.362,-3.081],[1.342,-3.02]],[[0.871,-2.357],[0.886,-2.291],[0.964,-2.243],[1.03,-2.263],[1.063,-2.301],[1.099,-2.499],[1.2,-3.369],[1.195,-3.455],[1.132,-3.504],[1.066,-3.498],[1.023,-3.45]],[[2.167,-4.012],[2.177,-3.972],[2.215,-3.934],[3.096,-3.276],[3.172,-3.26],[3.205,-3.283],[3.22,-3.329],[3.187,-3.362],[2.24,-4.076],[2.2,-4.065]],[[1.073,-4.812],[1.132,-4.749],[1.329,-4.744],[1.387,-4.782],[1.382,-4.812],[1.339,-4.85],[1.182,-4.86],[1.116,-4.85]]],"buttpad":[[[-2.104,1.451],[0.327,1.451],[0.327,0.033],[0.332,-0.321],[0.337,-0.575],[0.332,-0.828],[0.352,-1.081],[0.382,-1.334],[0.428,-1.587],[0.473,-1.84],[0.519,-2.093],[0.559,-2.347],[0.6,-2.6],[0.63,-2.853],[0.666,-3.106],[0.691,-3.359],[0.721,-3.612],[0.747,-3.866],[0.772,-4.119],[0.792,-4.372],[0.818,-4.625],[0.843,-4.878],[0.868,-5.131],[0.883,-5.283],[0.904,-6.078],[-2.104,-6.078]]],"frame":[[[0.777,-1.562],[4.478,-1.562],[4.478,-6.078],[1.253,-6.078],[1.233,-5.283],[1.218,-5.131],[1.192,-4.878],[1.167,-4.625],[1.142,-4.372],[1.121,-4.119],[1.096,-3.866],[1.071,-3.612],[1.04,-3.359],[1.015,-3.106],[0.98,-2.853],[0.949,-2.6],[0.909,-2.347],[0.868,-2.093],[0.823,-1.84],[0.777,-1.587]]]},"front":{}},"placement":{"side":{"plane":"xy","offset":{"y":"tube_axis_below_top"}},"front":{"plane":"zy","offset":{"y":"tube_axis_below_top"}}},"bounds":{"min":[0,-4.495,-0.848],"max":[6.967,0.72,0.848]},"volume_in3":16.3514,"centroid":[2.9286,-1.2194,0.002],"shell":[2.8275,-1.0711,0.0012],"area_in2":122.8724,"triangles":7438,"manifold":true,"slabs":[[0,-2.634,-0.848,0.387,0.711,0.848],[0.387,-4.469,-0.848,0.774,0.72,0.848],[0.774,-4.495,-0.848,1.548,0.668,0.848],[1.548,-4.412,-0.848,1.935,0.668,0.848],[1.935,-3.952,-0.848,2.322,0.668,0.848],[2.322,-3.682,-0.848,2.709,0.667,0.848],[2.709,-3.412,-0.848,3.096,0.667,0.848],[3.096,-3.141,-0.848,3.484,0.667,0.848],[3.484,-2.871,-0.848,3.871,0.666,0.848],[3.871,-2.601,-0.848,4.258,0.666,0.848],[4.258,-2.341,-0.848,4.645,0.666,0.848],[4.645,-2.113,-0.848,5.032,0.666,0.848],[5.032,-1.835,-0.848,5.419,0.665,0.848],[5.419,-1.572,-0.848,5.806,0.665,0.848],[5.806,-1.386,-0.848,6.967,0.665,0.848]],"slots":["body","buttpad"]},"magpul-mbus-3-front.folded":{"part":"magpul-mbus-3-front","component":"folded","model":"magpul-mbus-3-front.folded.glb","script":"magpul_mbus_3_front.py","inputs":{"magpul-mbus-3-front.body_width":1.143,"magpul-mbus-3-front.bolt_below_rail":0.007,"magpul-mbus-3-front.bolt_x":0.061,"magpul-mbus-3-front.boss_d":0.425,"magpul-mbus-3-front.boss_out":0.078,"magpul-mbus-3-front.clamp_below_rail":0.248,"magpul-mbus-3-front.clamp_length":0.692,"magpul-mbus-3-front.height_up":1.488,"magpul-mbus-3-front.hinge_behind_front":0.862,"magpul-mbus-3-front.hinge_y":0.22,"magpul-mbus-3-front.knuckle_d":0.421,"magpul-mbus-3-front.length":2.13,"magpul-mbus-3-front.length_up":1.072,"magpul-mbus-3-front.post_width_match":0.04,"magpul-mbus-3-front.post_width_standard":0.06,"magpul-mbus-3-front.screw_head_d":0.349,"magpul-mbus-3-front.screw_head_out":0.053,"magpul-mbus-3-front.sight_line_above_rail":1.41,"magpul-mbus-3-front.wheel_d":0.407,"magpul-mbus-3-front.wheel_flutes":12,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{"side":[[-0.727,1.41],[-0.727,0.216],[-0.717,0.156],[-0.686,0.096],[-0.64,0.05],[-0.562,0],[-0.354,0],[-0.346,-0.009],[-0.296,-0.188],[-0.265,-0.225],[-0.244,-0.237],[-0.184,-0.249],[0.235,-0.249],[0.274,-0.244],[0.304,-0.23],[0.337,-0.188],[0.347,-0.154],[0.347,-0.022],[0.335,0.069],[0.277,0.29],[0.253,0.335],[0.205,0.373],[0.108,0.397],[-0.074,0.426],[-0.135,0.432],[-0.24,0.431],[-0.245,0.426],[-0.251,0.43],[-0.287,0.386],[-0.291,0.315],[-0.298,0.309],[-0.305,0.316],[-0.31,0.976],[-0.315,0.997],[-0.331,1.015],[-0.337,1.076],[-0.306,1.106],[-0.304,1.141],[-0.312,1.153],[-0.339,1.153],[-0.345,1.159],[-0.364,1.367],[-0.382,1.4],[-0.415,1.426],[-0.618,1.483],[-0.664,1.489],[-0.688,1.483],[-0.709,1.463]],"rear":[[-0.649,-0.191],[-0.642,-0.202],[-0.625,-0.207],[-0.515,-0.224],[-0.473,-0.247],[-0.344,-0.248],[-0.345,-0.189],[-0.351,-0.183],[-0.354,-0.205],[-0.472,-0.202],[-0.469,-0.156],[-0.382,-0.155],[-0.391,-0.142],[-0.4,-0.139],[-0.398,-0.104],[0.399,-0.104],[0.402,-0.139],[0.381,-0.154],[0.47,-0.155],[0.472,-0.198],[0.363,-0.2],[0.36,-0.181],[0.353,-0.181],[0.345,-0.189],[0.344,-0.248],[0.47,-0.248],[0.495,-0.234],[0.555,-0.229],[0.57,-0.222],[0.574,0.171],[0.57,0.333],[0.527,0.378],[0.527,0.44],[0.518,0.491],[0.444,0.674],[0.429,0.729],[0.402,1.34],[0.347,1.483],[0.341,1.488],[0.284,1.488],[0.269,1.476],[0.247,1.204],[0.237,1.182],[0.213,1.16],[0.185,1.152],[-0.012,1.156],[-0.016,1.152],[-0.186,1.152],[-0.223,1.166],[-0.238,1.183],[-0.248,1.208],[-0.27,1.479],[-0.281,1.488],[-0.341,1.488],[-0.348,1.483],[-0.401,1.336],[-0.425,0.762],[-0.432,0.715],[-0.513,0.506],[-0.527,0.443],[-0.527,0.377],[-0.571,0.33],[-0.571,0.205],[-0.637,0.191],[-0.648,0.182]],"front":[[-0.651,0.169],[-0.65,-0.19],[-0.636,-0.205],[-0.512,-0.225],[-0.469,-0.248],[-0.344,-0.248],[-0.345,-0.192],[-0.355,-0.179],[-0.359,-0.205],[-0.472,-0.202],[-0.469,-0.148],[-0.391,-0.148],[-0.4,-0.132],[-0.398,-0.104],[0.398,-0.104],[0.4,-0.139],[0.385,-0.148],[0.469,-0.148],[0.472,-0.202],[0.354,-0.205],[0.351,-0.182],[0.345,-0.189],[0.344,-0.248],[0.471,-0.248],[0.496,-0.234],[0.562,-0.229],[0.571,-0.219],[0.572,-0.181],[0.572,0.17],[0.571,0.329],[0.527,0.378],[0.527,0.443],[0.517,0.495],[0.443,0.677],[0.43,0.725],[0.4,1.344],[0.348,1.483],[0.341,1.488],[0.283,1.488],[0.27,1.479],[0.246,1.199],[0.221,1.165],[0.186,1.152],[0.065,1.152],[0.061,1.156],[0.058,1.152],[0.016,1.152],[0.013,1.156],[-0.184,1.152],[-0.217,1.162],[-0.24,1.186],[-0.248,1.21],[-0.271,1.481],[-0.282,1.488],[-0.347,1.484],[-0.401,1.34],[-0.425,0.758],[-0.433,0.711],[-0.517,0.494],[-0.526,0.452],[-0.527,0.379],[-0.57,0.332],[-0.571,0.205],[-0.639,0.19]],"plan":[[-0.727,-0.466],[-0.717,-0.492],[-0.687,-0.529],[-0.347,-0.529],[-0.328,-0.519],[-0.317,-0.53],[-0.301,-0.565],[-0.29,-0.572],[-0.157,-0.572],[-0.145,-0.586],[-0.135,-0.64],[-0.123,-0.651],[0.235,-0.651],[0.249,-0.647],[0.26,-0.636],[0.279,-0.54],[0.346,-0.471],[0.346,-0.103],[0.346,0.47],[0.287,0.53],[0.284,0.566],[0.278,0.571],[0.245,0.571],[0.24,0.576],[0.232,0.571],[-0.11,0.571],[-0.116,0.576],[-0.121,0.571],[-0.29,0.572],[-0.299,0.567],[-0.328,0.519],[-0.348,0.528],[-0.689,0.527],[-0.723,0.48]],"top":[[-0.727,0.47],[-0.725,-0.479],[-0.687,-0.528],[-0.341,-0.528],[-0.328,-0.518],[-0.294,-0.571],[-0.156,-0.571],[-0.145,-0.583],[-0.135,-0.639],[-0.122,-0.65],[0.249,-0.648],[0.26,-0.638],[0.281,-0.539],[0.347,-0.469],[0.347,0.465],[0.344,0.476],[0.287,0.533],[0.283,0.569],[0.24,0.575],[0.235,0.571],[-0.29,0.572],[-0.301,0.566],[-0.317,0.529],[-0.328,0.519],[-0.34,0.529],[-0.685,0.529],[-0.698,0.521]]},"features":{"side":{"pivot_pin":[[[-0.589,0.294],[-0.442,0.294],[-0.442,0.147],[-0.589,0.147]]],"latch_pin":[[[-0.213,0.331],[-0.113,0.331],[-0.113,0.231],[-0.213,0.231]]],"knuckle_face":[[[-0.692,0.396],[-0.34,0.396],[-0.34,0.044],[-0.692,0.044]]],"side_recess":[[[-0.454,1.283],[-0.458,1.305],[-0.474,1.321],[-0.576,1.345],[-0.596,1.339],[-0.608,1.321],[-0.61,1.299],[-0.61,0.368],[-0.453,0.368]]],"front_recess":[[[-0.28,1.174],[-0.347,1.174],[-0.309,0.782],[-0.28,0.782]]]},"rear":{"legs":[[[-0.527,0.379],[0.527,0.379],[0.527,0.01],[-0.527,0.01]]],"fork":[[[-0.345,0.338],[0.349,0.338],[0.349,-0.035],[-0.345,-0.035]]],"lugs":[[[-0.324,0.338],[-0.175,0.338],[-0.175,0.077],[-0.324,0.077]],[[0.175,0.338],[0.324,0.338],[0.324,0.077],[0.175,0.077]]],"spring":[[[-0.166,0.338],[0.166,0.338],[0.166,0.077],[-0.166,0.077]]],"window":[[[-0.173,1.044],[0.174,1.044],[0.174,0.706],[-0.173,0.706]]],"wheel":[[[-0.203,1.015],[0.204,1.015],[0.204,0.725],[-0.203,0.725]]],"pockets":[[[-0.371,0.623],[-0.109,0.623],[-0.109,0.501],[-0.371,0.501]],[[0.108,0.623],[0.365,0.623],[0.365,0.501],[0.108,0.501]]],"post_base":[[[-0.062,1.235],[0.061,1.235],[0.061,1.152],[-0.062,1.152]]],"post_stem":[[[-0.018,1.387],[0.019,1.387],[0.019,1.235],[-0.018,1.235]]]},"front":{"base":[[[0.671,-0.306],[0.671,0.334],[0.571,0.334],[0.472,0.429],[-0.473,0.429],[-0.571,0.334],[-0.678,0.334],[-0.678,-0.306]]],"pad":[[[0.152,1.151],[0.152,1.107],[0.274,1.075],[0.289,1.032],[0.289,0.586],[0.274,0.553],[0.23,0.536],[-0.228,0.536],[-0.271,0.553],[-0.287,0.586],[-0.287,1.032],[-0.271,1.075],[-0.151,1.107],[-0.151,1.151]]],"window":[[[0.223,1.044],[-0.223,1.044],[-0.223,0.703],[0.223,0.703]]],"channel":[[[0.421,0],[-0.421,0],[-0.421,-0.107],[-0.344,-0.187],[-0.344,-0.306],[0.343,-0.306],[0.343,-0.187],[0.421,-0.108]]],"latch":[[[0.421,0.455],[-0.421,0.455],[-0.421,0.216],[0.421,0.216]]]},"plan":{"bolt":[[[0.159,-0.434],[-0.036,-0.434],[-0.036,0.431],[0.159,0.431]]]},"top":{"latch":[[[0.316,0.424],[-0.275,0.424],[-0.275,-0.424],[0.316,-0.424]]]}},"placement":{"side":{"plane":"xy","offset":{}},"rear":{"plane":"zy","offset":{}},"front":{"plane":"zy","offset":{}},"plan":{"plane":"xz","offset":{}},"top":{"plane":"xz","offset":{}}},"bounds":{"min":[-1.784,-0.248,-0.6495],"max":[0.346,0.455,0.6275]},"volume_in3":0.7916,"centroid":[-0.4664,0.1704,0.0009],"shell":[-0.5194,0.1442,0.0118],"area_in2":12.0266,"triangles":17380,"manifold":true,"rail_seat":{"x":[-0.5677,0.346],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-1.784,0.009,-0.424,-1.074,0.432,0.427],[-1.074,0,-0.531,-0.364,0.437,0.531],[-0.364,-0.248,-0.65,0.346,0.455,0.627]],"slots":["body","hardware"]},"magpul-mbus-3-front.up":{"part":"magpul-mbus-3-front","component":"up","model":"magpul-mbus-3-front.up.glb","script":"magpul_mbus_3_front.py","inputs":{"magpul-mbus-3-front.body_width":1.143,"magpul-mbus-3-front.bolt_below_rail":0.007,"magpul-mbus-3-front.bolt_x":0.061,"magpul-mbus-3-front.boss_d":0.425,"magpul-mbus-3-front.boss_out":0.078,"magpul-mbus-3-front.clamp_below_rail":0.248,"magpul-mbus-3-front.clamp_length":0.692,"magpul-mbus-3-front.height_up":1.488,"magpul-mbus-3-front.hinge_behind_front":0.862,"magpul-mbus-3-front.hinge_y":0.22,"magpul-mbus-3-front.knuckle_d":0.421,"magpul-mbus-3-front.length":2.13,"magpul-mbus-3-front.length_up":1.072,"magpul-mbus-3-front.post_width_match":0.04,"magpul-mbus-3-front.post_width_standard":0.06,"magpul-mbus-3-front.screw_head_d":0.349,"magpul-mbus-3-front.screw_head_out":0.053,"magpul-mbus-3-front.sight_line_above_rail":1.41,"magpul-mbus-3-front.wheel_d":0.407,"magpul-mbus-3-front.wheel_flutes":12,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{"side":[[-0.727,1.41],[-0.727,0.216],[-0.717,0.156],[-0.686,0.096],[-0.64,0.05],[-0.562,0],[-0.354,0],[-0.346,-0.009],[-0.296,-0.188],[-0.265,-0.225],[-0.244,-0.237],[-0.184,-0.249],[0.235,-0.249],[0.274,-0.244],[0.304,-0.23],[0.337,-0.188],[0.347,-0.154],[0.347,-0.022],[0.335,0.069],[0.277,0.29],[0.253,0.335],[0.205,0.373],[0.108,0.397],[-0.074,0.426],[-0.135,0.432],[-0.24,0.431],[-0.245,0.426],[-0.251,0.43],[-0.287,0.386],[-0.291,0.315],[-0.298,0.309],[-0.305,0.316],[-0.31,0.976],[-0.315,0.997],[-0.331,1.015],[-0.337,1.076],[-0.306,1.106],[-0.304,1.141],[-0.312,1.153],[-0.339,1.153],[-0.345,1.159],[-0.364,1.367],[-0.382,1.4],[-0.415,1.426],[-0.618,1.483],[-0.664,1.489],[-0.688,1.483],[-0.709,1.463]],"rear":[[-0.649,-0.191],[-0.642,-0.202],[-0.625,-0.207],[-0.515,-0.224],[-0.473,-0.247],[-0.344,-0.248],[-0.345,-0.189],[-0.351,-0.183],[-0.354,-0.205],[-0.472,-0.202],[-0.469,-0.156],[-0.382,-0.155],[-0.391,-0.142],[-0.4,-0.139],[-0.398,-0.104],[0.399,-0.104],[0.402,-0.139],[0.381,-0.154],[0.47,-0.155],[0.472,-0.198],[0.363,-0.2],[0.36,-0.181],[0.353,-0.181],[0.345,-0.189],[0.344,-0.248],[0.47,-0.248],[0.495,-0.234],[0.555,-0.229],[0.57,-0.222],[0.574,0.171],[0.57,0.333],[0.527,0.378],[0.527,0.44],[0.518,0.491],[0.444,0.674],[0.429,0.729],[0.402,1.34],[0.347,1.483],[0.341,1.488],[0.284,1.488],[0.269,1.476],[0.247,1.204],[0.237,1.182],[0.213,1.16],[0.185,1.152],[-0.012,1.156],[-0.016,1.152],[-0.186,1.152],[-0.223,1.166],[-0.238,1.183],[-0.248,1.208],[-0.27,1.479],[-0.281,1.488],[-0.341,1.488],[-0.348,1.483],[-0.401,1.336],[-0.425,0.762],[-0.432,0.715],[-0.513,0.506],[-0.527,0.443],[-0.527,0.377],[-0.571,0.33],[-0.571,0.205],[-0.637,0.191],[-0.648,0.182]],"front":[[-0.651,0.169],[-0.65,-0.19],[-0.636,-0.205],[-0.512,-0.225],[-0.469,-0.248],[-0.344,-0.248],[-0.345,-0.192],[-0.355,-0.179],[-0.359,-0.205],[-0.472,-0.202],[-0.469,-0.148],[-0.391,-0.148],[-0.4,-0.132],[-0.398,-0.104],[0.398,-0.104],[0.4,-0.139],[0.385,-0.148],[0.469,-0.148],[0.472,-0.202],[0.354,-0.205],[0.351,-0.182],[0.345,-0.189],[0.344,-0.248],[0.471,-0.248],[0.496,-0.234],[0.562,-0.229],[0.571,-0.219],[0.572,-0.181],[0.572,0.17],[0.571,0.329],[0.527,0.378],[0.527,0.443],[0.517,0.495],[0.443,0.677],[0.43,0.725],[0.4,1.344],[0.348,1.483],[0.341,1.488],[0.283,1.488],[0.27,1.479],[0.246,1.199],[0.221,1.165],[0.186,1.152],[0.065,1.152],[0.061,1.156],[0.058,1.152],[0.016,1.152],[0.013,1.156],[-0.184,1.152],[-0.217,1.162],[-0.24,1.186],[-0.248,1.21],[-0.271,1.481],[-0.282,1.488],[-0.347,1.484],[-0.401,1.34],[-0.425,0.758],[-0.433,0.711],[-0.517,0.494],[-0.526,0.452],[-0.527,0.379],[-0.57,0.332],[-0.571,0.205],[-0.639,0.19]],"plan":[[-0.727,-0.466],[-0.717,-0.492],[-0.687,-0.529],[-0.347,-0.529],[-0.328,-0.519],[-0.317,-0.53],[-0.301,-0.565],[-0.29,-0.572],[-0.157,-0.572],[-0.145,-0.586],[-0.135,-0.64],[-0.123,-0.651],[0.235,-0.651],[0.249,-0.647],[0.26,-0.636],[0.279,-0.54],[0.346,-0.471],[0.346,-0.103],[0.346,0.47],[0.287,0.53],[0.284,0.566],[0.278,0.571],[0.245,0.571],[0.24,0.576],[0.232,0.571],[-0.11,0.571],[-0.116,0.576],[-0.121,0.571],[-0.29,0.572],[-0.299,0.567],[-0.328,0.519],[-0.348,0.528],[-0.689,0.527],[-0.723,0.48]],"top":[[-0.727,0.47],[-0.725,-0.479],[-0.687,-0.528],[-0.341,-0.528],[-0.328,-0.518],[-0.294,-0.571],[-0.156,-0.571],[-0.145,-0.583],[-0.135,-0.639],[-0.122,-0.65],[0.249,-0.648],[0.26,-0.638],[0.281,-0.539],[0.347,-0.469],[0.347,0.465],[0.344,0.476],[0.287,0.533],[0.283,0.569],[0.24,0.575],[0.235,0.571],[-0.29,0.572],[-0.301,0.566],[-0.317,0.529],[-0.328,0.519],[-0.34,0.529],[-0.685,0.529],[-0.698,0.521]]},"features":{"side":{"pivot_pin":[[[-0.589,0.294],[-0.442,0.294],[-0.442,0.147],[-0.589,0.147]]],"latch_pin":[[[-0.213,0.331],[-0.113,0.331],[-0.113,0.231],[-0.213,0.231]]],"knuckle_face":[[[-0.692,0.396],[-0.34,0.396],[-0.34,0.044],[-0.692,0.044]]],"side_recess":[[[-0.454,1.283],[-0.458,1.305],[-0.474,1.321],[-0.576,1.345],[-0.596,1.339],[-0.608,1.321],[-0.61,1.299],[-0.61,0.368],[-0.453,0.368]]],"front_recess":[[[-0.28,1.174],[-0.347,1.174],[-0.309,0.782],[-0.28,0.782]]]},"rear":{"legs":[[[-0.527,0.379],[0.527,0.379],[0.527,0.01],[-0.527,0.01]]],"fork":[[[-0.345,0.338],[0.349,0.338],[0.349,-0.035],[-0.345,-0.035]]],"lugs":[[[-0.324,0.338],[-0.175,0.338],[-0.175,0.077],[-0.324,0.077]],[[0.175,0.338],[0.324,0.338],[0.324,0.077],[0.175,0.077]]],"spring":[[[-0.166,0.338],[0.166,0.338],[0.166,0.077],[-0.166,0.077]]],"window":[[[-0.173,1.044],[0.174,1.044],[0.174,0.706],[-0.173,0.706]]],"wheel":[[[-0.203,1.015],[0.204,1.015],[0.204,0.725],[-0.203,0.725]]],"pockets":[[[-0.371,0.623],[-0.109,0.623],[-0.109,0.501],[-0.371,0.501]],[[0.108,0.623],[0.365,0.623],[0.365,0.501],[0.108,0.501]]],"post_base":[[[-0.062,1.235],[0.061,1.235],[0.061,1.152],[-0.062,1.152]]],"post_stem":[[[-0.018,1.387],[0.019,1.387],[0.019,1.235],[-0.018,1.235]]]},"front":{"base":[[[0.671,-0.306],[0.671,0.334],[0.571,0.334],[0.472,0.429],[-0.473,0.429],[-0.571,0.334],[-0.678,0.334],[-0.678,-0.306]]],"pad":[[[0.152,1.151],[0.152,1.107],[0.274,1.075],[0.289,1.032],[0.289,0.586],[0.274,0.553],[0.23,0.536],[-0.228,0.536],[-0.271,0.553],[-0.287,0.586],[-0.287,1.032],[-0.271,1.075],[-0.151,1.107],[-0.151,1.151]]],"window":[[[0.223,1.044],[-0.223,1.044],[-0.223,0.703],[0.223,0.703]]],"channel":[[[0.421,0],[-0.421,0],[-0.421,-0.107],[-0.344,-0.187],[-0.344,-0.306],[0.343,-0.306],[0.343,-0.187],[0.421,-0.108]]],"latch":[[[0.421,0.455],[-0.421,0.455],[-0.421,0.216],[0.421,0.216]]]},"plan":{"bolt":[[[0.159,-0.434],[-0.036,-0.434],[-0.036,0.431],[0.159,0.431]]]},"top":{"latch":[[[0.316,0.424],[-0.275,0.424],[-0.275,-0.424],[0.316,-0.424]]]}},"placement":{"side":{"plane":"xy","offset":{}},"rear":{"plane":"zy","offset":{}},"front":{"plane":"zy","offset":{}},"plan":{"plane":"xz","offset":{}},"top":{"plane":"xz","offset":{}}},"bounds":{"min":[-0.727,-0.248,-0.6495],"max":[0.346,1.488,0.6275]},"volume_in3":0.7916,"centroid":[-0.2548,0.3858,0.0009],"shell":[-0.2874,0.3819,0.0118],"area_in2":12.0266,"triangles":17380,"manifold":true,"rail_seat":{"x":[-0.5677,0.346],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-0.727,-0.248,-0.65,0.346,0.446,0.627],[-0.727,0.446,-0.526,-0.039,0.794,0.526],[-0.727,0.794,-0.424,-0.304,1.488,0.426]],"slots":["body","hardware"]},"magpul-mbus-3-rear.folded":{"part":"magpul-mbus-3-rear","component":"folded","model":"magpul-mbus-3-rear.folded.glb","script":"magpul_mbus_3_rear.py","inputs":{"magpul-mbus-3-rear.aperture_large_d":0.19,"magpul-mbus-3-rear.aperture_small_d":0.063,"magpul-mbus-3-rear.clamp_bottom_y":-0.253,"magpul-mbus-3-rear.clamp_front_x":0.343,"magpul-mbus-3-rear.clamp_screw_hex":0.125,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{"rear":[[-0.667,0.063],[-0.654,0.046],[-0.527,0.025],[-0.484,0.001],[-0.358,0],[-0.353,0.002],[-0.354,0.062],[-0.359,0.067],[-0.363,0.046],[-0.484,0.049],[-0.481,0.096],[-0.391,0.097],[-0.415,0.125],[-0.412,0.15],[0.414,0.15],[0.412,0.113],[0.393,0.101],[0.482,0.096],[0.485,0.052],[0.365,0.049],[0.361,0.069],[0.354,0.061],[0.354,0.002],[0.473,0],[0.509,0.016],[0.583,0.023],[0.589,0.07],[0.587,0.593],[0.542,0.643],[0.539,0.774],[0.488,0.924],[0.484,1.05],[0.507,1.08],[0.51,1.107],[0.656,1.116],[0.694,1.136],[0.712,1.153],[0.713,1.522],[0.705,1.538],[0.662,1.563],[0.507,1.576],[0.506,1.604],[0.484,1.631],[0.483,1.81],[0.439,1.937],[0.43,1.949],[0.335,1.949],[0.31,1.917],[0.305,1.433],[0.3,1.428],[0.166,1.433],[0.165,1.79],[0.146,1.828],[0.102,1.846],[-0.104,1.846],[-0.127,1.84],[-0.147,1.826],[-0.161,1.805],[-0.166,1.774],[-0.165,1.433],[-0.301,1.429],[-0.31,1.918],[-0.332,1.949],[-0.431,1.949],[-0.483,1.807],[-0.484,0.946],[-0.495,0.894],[-0.525,0.823],[-0.537,0.777],[-0.541,0.642],[-0.586,0.596],[-0.587,0.467],[-0.653,0.453],[-0.666,0.442]],"side":[[-1.176,1.364],[-1.173,1.299],[-1.159,1.239],[-1.135,1.19],[-1.101,1.144],[-1.101,0.463],[-1.085,0.397],[-1.067,0.363],[-1.025,0.316],[-0.93,0.255],[-0.718,0.255],[-0.71,0.242],[-0.671,0.09],[-0.657,0.059],[-0.615,0.016],[-0.557,0],[-0.09,0.001],[-0.05,0.016],[-0.023,0.04],[-0.008,0.068],[0,0.102],[0,0.229],[-0.011,0.321],[-0.075,0.563],[-0.102,0.605],[-0.125,0.626],[-0.179,0.65],[-0.395,0.687],[-0.489,0.698],[-0.601,0.697],[-0.639,0.665],[-0.653,0.635],[-0.655,0.582],[-0.66,0.577],[-0.671,0.582],[-0.671,1.145],[-0.634,1.194],[-0.601,1.28],[-0.596,1.347],[-0.606,1.416],[-0.641,1.497],[-0.698,1.563],[-0.726,1.807],[-0.748,1.857],[-0.792,1.888],[-1.028,1.949],[-1.047,1.948],[-1.071,1.936],[-1.09,1.914],[-1.099,1.888],[-1.101,1.535],[-1.13,1.498],[-1.152,1.457]],"plan":[[-1.171,0.393],[-1.166,0.379],[-1.098,0.306],[-1.1,-0.51],[-1.073,-0.553],[-1.055,-0.565],[-0.705,-0.565],[-0.69,-0.552],[-0.662,-0.606],[-0.652,-0.61],[-0.512,-0.609],[-0.504,-0.617],[-0.493,-0.679],[-0.48,-0.69],[-0.101,-0.688],[-0.088,-0.675],[-0.068,-0.577],[0,-0.505],[-0.001,0],[0,0.461],[-0.06,0.521],[-0.066,0.562],[-0.109,0.567],[-0.113,0.563],[-0.468,0.563],[-0.472,0.567],[-0.477,0.563],[-0.648,0.563],[-0.654,0.57],[-0.66,0.646],[-0.696,0.69],[-1.063,0.69],[-1.074,0.686],[-1.103,0.638],[-1.112,0.49],[-1.118,0.484],[-1.141,0.485],[-1.166,0.469]]},"features":{"rear":{"yoke":[[[-0.334,1.949],[-0.434,1.949],[-0.439,1.933],[-0.466,1.854],[-0.483,1.805],[-0.483,0.96],[-0.485,0.938],[-0.489,0.916],[-0.496,0.893],[-0.505,0.871],[-0.514,0.849],[-0.523,0.826],[-0.53,0.804],[-0.535,0.782],[-0.539,0.759],[-0.54,0.715],[-0.54,0.301],[-0.526,0.29],[-0.502,0.273],[-0.488,0.266],[-0.333,0.266],[-0.333,0.58],[-0.327,0.596],[-0.311,0.603],[0.313,0.603],[0.329,0.596],[0.335,0.58],[0.335,0.266],[0.489,0.266],[0.504,0.273],[0.527,0.29],[0.541,0.301],[0.541,0.715],[0.54,0.759],[0.537,0.782],[0.531,0.804],[0.525,0.826],[0.516,0.849],[0.507,0.871],[0.498,0.893],[0.491,0.916],[0.487,0.938],[0.484,0.96],[0.484,1.805],[0.468,1.854],[0.441,1.933],[0.436,1.949],[0.335,1.949],[0.322,1.933],[0.311,1.854],[0.308,1.698],[0.306,1.343],[0.302,0.983],[0.3,0.916],[0.299,0.893],[0.294,0.871],[0.282,0.849],[0.264,0.832],[0.238,0.822],[-0.236,0.822],[-0.262,0.832],[-0.28,0.849],[-0.292,0.871],[-0.297,0.893],[-0.298,0.916],[-0.3,0.983],[-0.304,1.343],[-0.306,1.698],[-0.31,1.854],[-0.32,1.933]]],"web":[[[-0.315,1.123],[0.316,1.123],[0.316,0.804],[-0.315,0.804]]],"plate":[[[0.166,0.882],[0.164,0.867],[0.158,0.854],[0.147,0.844],[0.134,0.837],[0.12,0.835],[-0.118,0.835],[-0.133,0.837],[-0.146,0.844],[-0.156,0.854],[-0.163,0.867],[-0.165,0.882],[-0.165,1.799],[-0.163,1.814],[-0.156,1.827],[-0.146,1.837],[-0.133,1.844],[-0.118,1.846],[0.12,1.846],[0.134,1.844],[0.147,1.837],[0.158,1.827],[0.164,1.814],[0.166,1.799]]],"aperture_small":[[[0.037,1.679],[0.036,1.686],[0.034,1.693],[0.031,1.699],[0.026,1.705],[0.021,1.709],[0.015,1.713],[0.008,1.715],[0.001,1.715],[-0.006,1.715],[-0.013,1.713],[-0.019,1.709],[-0.024,1.705],[-0.029,1.699],[-0.032,1.693],[-0.034,1.686],[-0.035,1.679],[-0.034,1.673],[-0.032,1.666],[-0.029,1.66],[-0.024,1.654],[-0.019,1.65],[-0.013,1.646],[-0.006,1.644],[0.001,1.644],[0.008,1.644],[0.015,1.646],[0.021,1.65],[0.026,1.654],[0.031,1.66],[0.034,1.666],[0.036,1.673]]],"aperture_large":[[[0.097,0.999],[0.095,1.018],[0.09,1.037],[0.081,1.053],[0.069,1.068],[0.054,1.08],[0.037,1.089],[0.019,1.095],[0,1.097],[-0.019,1.095],[-0.037,1.089],[-0.054,1.08],[-0.069,1.068],[-0.081,1.053],[-0.09,1.037],[-0.095,1.018],[-0.097,0.999],[-0.095,0.98],[-0.09,0.962],[-0.081,0.945],[-0.069,0.931],[-0.054,0.919],[-0.037,0.909],[-0.019,0.904],[0,0.902],[0.019,0.904],[0.037,0.909],[0.054,0.919],[0.069,0.931],[0.081,0.945],[0.09,0.962],[0.095,0.98]]],"aperture_ring":[[[0.065,1.679],[0.064,1.692],[0.06,1.704],[0.054,1.715],[0.046,1.724],[0.037,1.732],[0.025,1.738],[0.014,1.742],[0.001,1.743],[-0.011,1.742],[-0.023,1.738],[-0.034,1.732],[-0.044,1.724],[-0.052,1.715],[-0.058,1.704],[-0.061,1.692],[-0.063,1.679],[-0.061,1.667],[-0.058,1.655],[-0.052,1.644],[-0.044,1.634],[-0.034,1.627],[-0.023,1.621],[-0.011,1.617],[0.001,1.616],[0.014,1.617],[0.025,1.621],[0.037,1.627],[0.046,1.634],[0.054,1.644],[0.06,1.655],[0.064,1.667]]],"windage_screw":[[[-0.465,1.422],[0.507,1.422],[0.507,1.262],[-0.465,1.262]]],"knob_collar":[[[0.484,1.633],[0.493,1.633],[0.507,1.616],[0.507,1.068],[0.493,1.051],[0.484,1.051]]],"knob_grip":[[[0.507,1.573],[0.664,1.567],[0.713,1.541],[0.713,1.143],[0.664,1.117],[0.507,1.111]]],"flange_left":[[[-0.143,1.549],[-0.068,1.549],[-0.068,1.135],[-0.143,1.135]]],"flange_right":[[[0.07,1.549],[0.145,1.549],[0.145,1.135],[0.07,1.135]]],"traveller":[[[-0.068,1.476],[0.07,1.476],[0.07,1.208],[-0.068,1.208]]],"clamp_boss":[[[-0.586,0.465],[-0.667,0.443],[-0.667,0.052],[-0.586,0.03]]],"screw_head":[[[0.587,0.425],[0.669,0.425],[0.669,0.07],[0.587,0.07]]],"base":[[[-0.488,0.697],[-0.587,0.597],[-0.587,0.068],[-0.485,0],[-0.353,0],[-0.353,0.064],[-0.422,0.134],[-0.437,0.149],[-0.448,0.159],[-0.448,0.229],[-0.441,0.245],[-0.424,0.253],[0.424,0.253],[0.441,0.245],[0.448,0.229],[0.448,0.159],[0.437,0.149],[0.422,0.134],[0.353,0.064],[0.353,0],[0.485,0],[0.587,0.068],[0.587,0.597],[0.488,0.697]]],"knuckle_left":[[[-0.333,0.603],[-0.178,0.603],[-0.178,0.253],[-0.333,0.253]]],"knuckle_right":[[[0.178,0.603],[0.334,0.603],[0.334,0.253],[0.178,0.253]]],"spring":[[[-0.164,0.603],[0.166,0.603],[0.166,0.357],[-0.164,0.357]]],"rail_top":[[[-0.424,0.253],[0.424,0.253],[0.424,0.25],[-0.424,0.25]]]},"side":{"arm":[[[-0.669,0.465],[-0.669,0.517],[-0.673,0.527],[-0.673,0.533],[-0.669,0.536],[-0.669,1.177],[-0.673,1.3],[-0.679,1.4],[-0.687,1.467],[-0.687,1.481],[-0.691,1.498],[-0.691,1.513],[-0.696,1.547],[-0.701,1.603],[-0.715,1.708],[-0.72,1.756],[-0.73,1.823],[-0.741,1.849],[-0.749,1.859],[-0.767,1.876],[-0.784,1.885],[-1.009,1.947],[-1.025,1.949],[-1.051,1.947],[-1.068,1.939],[-1.086,1.921],[-1.095,1.903],[-1.102,1.868],[-1.102,0.531],[-1.097,0.528],[-1.102,0.518],[-1.102,0.474],[-1.096,0.43],[-1.094,0.427],[-1.094,0.422],[-1.085,0.396],[-1.076,0.377],[-1.063,0.356],[-1.043,0.331],[-1.014,0.306],[-0.974,0.283],[-0.945,0.273],[-0.936,0.272],[-0.934,0.269],[-0.902,0.265],[-0.871,0.265],[-0.839,0.269],[-0.805,0.279],[-0.764,0.301],[-0.738,0.322],[-0.709,0.355],[-0.692,0.383],[-0.676,0.424]]],"base":[[[0,0.099],[0,0.237],[-0.006,0.291],[-0.011,0.324],[-0.027,0.377],[-0.039,0.431],[-0.044,0.441],[-0.045,0.452],[-0.049,0.462],[-0.049,0.469],[-0.053,0.476],[-0.07,0.552],[-0.085,0.584],[-0.095,0.598],[-0.109,0.614],[-0.128,0.629],[-0.137,0.633],[-0.139,0.636],[-0.177,0.65],[-0.25,0.663],[-0.253,0.665],[-0.294,0.671],[-0.299,0.673],[-0.463,0.696],[-0.484,0.698],[-0.592,0.697],[-0.604,0.694],[-0.619,0.686],[-0.635,0.672],[-0.649,0.649],[-0.655,0.622],[-0.656,0.472],[-0.66,0.434],[-0.671,0.401],[-0.678,0.386],[-0.678,0.383],[-0.687,0.369],[-0.691,0.36],[-0.704,0.344],[-0.712,0.327],[-0.719,0.302],[-0.72,0.279],[-0.716,0.259],[-0.713,0.252],[-0.712,0.242],[-0.71,0.24],[-0.701,0.199],[-0.696,0.191],[-0.696,0.185],[-0.679,0.128],[-0.671,0.088],[-0.653,0.051],[-0.626,0.022],[-0.604,0.01],[-0.583,0.003],[-0.559,0],[-0.096,0],[-0.066,0.007],[-0.052,0.016],[-0.049,0.016],[-0.025,0.037],[-0.008,0.065]]],"hinge":[[[-1.066,0.481],[-1.063,0.517],[-1.053,0.551],[-1.036,0.582],[-1.013,0.609],[-0.986,0.632],[-0.955,0.649],[-0.921,0.659],[-0.885,0.662],[-0.85,0.659],[-0.816,0.649],[-0.785,0.632],[-0.757,0.609],[-0.735,0.582],[-0.718,0.551],[-0.708,0.517],[-0.704,0.481],[-0.708,0.446],[-0.718,0.412],[-0.735,0.381],[-0.757,0.353],[-0.785,0.331],[-0.816,0.314],[-0.85,0.304],[-0.885,0.3],[-0.921,0.304],[-0.955,0.314],[-0.986,0.331],[-1.013,0.353],[-1.036,0.381],[-1.053,0.412],[-1.063,0.446]]],"windage":[[[-1.068,1.343],[-1.065,1.378],[-1.054,1.412],[-1.038,1.443],[-1.015,1.471],[-0.987,1.493],[-0.956,1.51],[-0.922,1.521],[-0.887,1.524],[-0.851,1.521],[-0.817,1.51],[-0.786,1.493],[-0.758,1.471],[-0.736,1.443],[-0.719,1.412],[-0.709,1.378],[-0.705,1.343],[-0.709,1.307],[-0.719,1.273],[-0.736,1.242],[-0.758,1.214],[-0.786,1.192],[-0.817,1.175],[-0.851,1.165],[-0.887,1.161],[-0.922,1.165],[-0.956,1.175],[-0.987,1.192],[-1.015,1.214],[-1.038,1.242],[-1.054,1.273],[-1.065,1.307]]],"bolt":[[[-0.467,0.248],[-0.464,0.282],[-0.454,0.314],[-0.438,0.345],[-0.416,0.371],[-0.39,0.393],[-0.36,0.409],[-0.327,0.419],[-0.293,0.422],[-0.259,0.419],[-0.226,0.409],[-0.196,0.393],[-0.17,0.371],[-0.148,0.345],[-0.132,0.314],[-0.122,0.282],[-0.119,0.248],[-0.122,0.214],[-0.132,0.181],[-0.148,0.151],[-0.17,0.124],[-0.196,0.103],[-0.226,0.087],[-0.259,0.077],[-0.293,0.073],[-0.327,0.077],[-0.36,0.087],[-0.39,0.103],[-0.416,0.124],[-0.438,0.151],[-0.454,0.181],[-0.464,0.214]]],"hinge_pin":[[[-0.933,0.481],[-0.932,0.49],[-0.929,0.5],[-0.925,0.508],[-0.919,0.515],[-0.912,0.521],[-0.904,0.525],[-0.895,0.528],[-0.885,0.529],[-0.876,0.528],[-0.867,0.525],[-0.859,0.521],[-0.851,0.515],[-0.846,0.508],[-0.841,0.5],[-0.838,0.49],[-0.837,0.481],[-0.838,0.472],[-0.841,0.463],[-0.846,0.455],[-0.851,0.447],[-0.859,0.441],[-0.867,0.437],[-0.876,0.434],[-0.885,0.433],[-0.895,0.434],[-0.904,0.437],[-0.912,0.441],[-0.919,0.447],[-0.925,0.455],[-0.929,0.463],[-0.932,0.472]]],"plate":[[[-1.028,1.846],[-1.099,1.846],[-1.099,0.835],[-1.028,0.835]]],"knuckle":[[[-0.681,0.603],[-0.885,0.603],[-0.909,0.601],[-0.932,0.594],[-0.953,0.582],[-0.971,0.567],[-0.986,0.549],[-0.998,0.528],[-1.005,0.505],[-1.007,0.481],[-1.007,0.253],[-0.681,0.253]]]},"plan":{"base":[[[0,-0.508],[0,0.462],[-0.003,0.463],[-0.003,0.467],[-0.059,0.52],[-0.069,0.523],[-0.094,0.534],[-0.126,0.555],[-0.132,0.563],[-0.139,0.564],[-0.652,0.564],[-0.648,0.484],[-0.623,0.484],[-0.623,0.481],[-0.617,0.477],[-0.605,0.471],[-0.599,0.461],[-0.596,0.359],[-0.607,0.345],[-0.625,0.334],[-0.631,0.329],[-0.632,0.326],[-0.653,0.314],[-0.666,0.302],[-0.666,-0.51],[-0.674,-0.524],[-0.688,-0.542],[-0.689,-0.55],[-0.664,-0.604],[-0.654,-0.61],[-0.139,-0.61],[-0.132,-0.609],[-0.099,-0.582],[-0.069,-0.568],[-0.059,-0.566],[-0.008,-0.518],[-0.003,-0.513],[-0.003,-0.509]]],"latch":[[[-0.667,-0.395],[-0.664,-0.414],[-0.655,-0.431],[-0.641,-0.445],[-0.624,-0.453],[-0.605,-0.456],[-0.101,-0.456],[-0.082,-0.453],[-0.065,-0.445],[-0.051,-0.431],[-0.043,-0.414],[-0.04,-0.395],[-0.04,0.355],[-0.043,0.374],[-0.051,0.391],[-0.065,0.404],[-0.082,0.413],[-0.101,0.416],[-0.605,0.416],[-0.624,0.413],[-0.641,0.404],[-0.655,0.391],[-0.664,0.374],[-0.667,0.355]]]}},"placement":{"rear":{"plane":"zy","offset":{"y":"clamp_bottom_y"}},"side":{"plane":"xy","offset":{"x":"clamp_front_x","y":"clamp_bottom_y"}},"plan":{"plane":"xz","offset":{"x":"clamp_front_x"}}},"bounds":{"min":[-2.01,-0.253,-0.667],"max":[0.343,0.5175,0.713]},"volume_in3":0.882,"centroid":[-0.6035,0.1785,0.023],"shell":[-0.7757,0.1691,0.0414],"area_in2":14.4321,"triangles":13602,"manifold":true,"rail_seat":{"x":[-0.377,0.343],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-2.01,0.012,-0.483,-1.618,0.423,0.683],[-1.618,-0.063,-0.483,-1.226,0.517,0.713],[-1.226,-0.002,-0.537,-0.833,0.456,0.713],[-0.833,0,-0.546,-0.441,0.445,0.547],[-0.441,-0.253,-0.667,0.343,0.444,0.669]],"slots":["body","hardware"]},"magpul-mbus-3-rear.up":{"part":"magpul-mbus-3-rear","component":"up","model":"magpul-mbus-3-rear.up.glb","script":"magpul_mbus_3_rear.py","inputs":{"magpul-mbus-3-rear.aperture_large_d":0.19,"magpul-mbus-3-rear.aperture_small_d":0.063,"magpul-mbus-3-rear.clamp_bottom_y":-0.253,"magpul-mbus-3-rear.clamp_front_x":0.343,"magpul-mbus-3-rear.clamp_screw_hex":0.125,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{"rear":[[-0.667,0.063],[-0.654,0.046],[-0.527,0.025],[-0.484,0.001],[-0.358,0],[-0.353,0.002],[-0.354,0.062],[-0.359,0.067],[-0.363,0.046],[-0.484,0.049],[-0.481,0.096],[-0.391,0.097],[-0.415,0.125],[-0.412,0.15],[0.414,0.15],[0.412,0.113],[0.393,0.101],[0.482,0.096],[0.485,0.052],[0.365,0.049],[0.361,0.069],[0.354,0.061],[0.354,0.002],[0.473,0],[0.509,0.016],[0.583,0.023],[0.589,0.07],[0.587,0.593],[0.542,0.643],[0.539,0.774],[0.488,0.924],[0.484,1.05],[0.507,1.08],[0.51,1.107],[0.656,1.116],[0.694,1.136],[0.712,1.153],[0.713,1.522],[0.705,1.538],[0.662,1.563],[0.507,1.576],[0.506,1.604],[0.484,1.631],[0.483,1.81],[0.439,1.937],[0.43,1.949],[0.335,1.949],[0.31,1.917],[0.305,1.433],[0.3,1.428],[0.166,1.433],[0.165,1.79],[0.146,1.828],[0.102,1.846],[-0.104,1.846],[-0.127,1.84],[-0.147,1.826],[-0.161,1.805],[-0.166,1.774],[-0.165,1.433],[-0.301,1.429],[-0.31,1.918],[-0.332,1.949],[-0.431,1.949],[-0.483,1.807],[-0.484,0.946],[-0.495,0.894],[-0.525,0.823],[-0.537,0.777],[-0.541,0.642],[-0.586,0.596],[-0.587,0.467],[-0.653,0.453],[-0.666,0.442]],"side":[[-1.176,1.364],[-1.173,1.299],[-1.159,1.239],[-1.135,1.19],[-1.101,1.144],[-1.101,0.463],[-1.085,0.397],[-1.067,0.363],[-1.025,0.316],[-0.93,0.255],[-0.718,0.255],[-0.71,0.242],[-0.671,0.09],[-0.657,0.059],[-0.615,0.016],[-0.557,0],[-0.09,0.001],[-0.05,0.016],[-0.023,0.04],[-0.008,0.068],[0,0.102],[0,0.229],[-0.011,0.321],[-0.075,0.563],[-0.102,0.605],[-0.125,0.626],[-0.179,0.65],[-0.395,0.687],[-0.489,0.698],[-0.601,0.697],[-0.639,0.665],[-0.653,0.635],[-0.655,0.582],[-0.66,0.577],[-0.671,0.582],[-0.671,1.145],[-0.634,1.194],[-0.601,1.28],[-0.596,1.347],[-0.606,1.416],[-0.641,1.497],[-0.698,1.563],[-0.726,1.807],[-0.748,1.857],[-0.792,1.888],[-1.028,1.949],[-1.047,1.948],[-1.071,1.936],[-1.09,1.914],[-1.099,1.888],[-1.101,1.535],[-1.13,1.498],[-1.152,1.457]],"plan":[[-1.171,0.393],[-1.166,0.379],[-1.098,0.306],[-1.1,-0.51],[-1.073,-0.553],[-1.055,-0.565],[-0.705,-0.565],[-0.69,-0.552],[-0.662,-0.606],[-0.652,-0.61],[-0.512,-0.609],[-0.504,-0.617],[-0.493,-0.679],[-0.48,-0.69],[-0.101,-0.688],[-0.088,-0.675],[-0.068,-0.577],[0,-0.505],[-0.001,0],[0,0.461],[-0.06,0.521],[-0.066,0.562],[-0.109,0.567],[-0.113,0.563],[-0.468,0.563],[-0.472,0.567],[-0.477,0.563],[-0.648,0.563],[-0.654,0.57],[-0.66,0.646],[-0.696,0.69],[-1.063,0.69],[-1.074,0.686],[-1.103,0.638],[-1.112,0.49],[-1.118,0.484],[-1.141,0.485],[-1.166,0.469]]},"features":{"rear":{"yoke":[[[-0.334,1.949],[-0.434,1.949],[-0.439,1.933],[-0.466,1.854],[-0.483,1.805],[-0.483,0.96],[-0.485,0.938],[-0.489,0.916],[-0.496,0.893],[-0.505,0.871],[-0.514,0.849],[-0.523,0.826],[-0.53,0.804],[-0.535,0.782],[-0.539,0.759],[-0.54,0.715],[-0.54,0.301],[-0.526,0.29],[-0.502,0.273],[-0.488,0.266],[-0.333,0.266],[-0.333,0.58],[-0.327,0.596],[-0.311,0.603],[0.313,0.603],[0.329,0.596],[0.335,0.58],[0.335,0.266],[0.489,0.266],[0.504,0.273],[0.527,0.29],[0.541,0.301],[0.541,0.715],[0.54,0.759],[0.537,0.782],[0.531,0.804],[0.525,0.826],[0.516,0.849],[0.507,0.871],[0.498,0.893],[0.491,0.916],[0.487,0.938],[0.484,0.96],[0.484,1.805],[0.468,1.854],[0.441,1.933],[0.436,1.949],[0.335,1.949],[0.322,1.933],[0.311,1.854],[0.308,1.698],[0.306,1.343],[0.302,0.983],[0.3,0.916],[0.299,0.893],[0.294,0.871],[0.282,0.849],[0.264,0.832],[0.238,0.822],[-0.236,0.822],[-0.262,0.832],[-0.28,0.849],[-0.292,0.871],[-0.297,0.893],[-0.298,0.916],[-0.3,0.983],[-0.304,1.343],[-0.306,1.698],[-0.31,1.854],[-0.32,1.933]]],"web":[[[-0.315,1.123],[0.316,1.123],[0.316,0.804],[-0.315,0.804]]],"plate":[[[0.166,0.882],[0.164,0.867],[0.158,0.854],[0.147,0.844],[0.134,0.837],[0.12,0.835],[-0.118,0.835],[-0.133,0.837],[-0.146,0.844],[-0.156,0.854],[-0.163,0.867],[-0.165,0.882],[-0.165,1.799],[-0.163,1.814],[-0.156,1.827],[-0.146,1.837],[-0.133,1.844],[-0.118,1.846],[0.12,1.846],[0.134,1.844],[0.147,1.837],[0.158,1.827],[0.164,1.814],[0.166,1.799]]],"aperture_small":[[[0.037,1.679],[0.036,1.686],[0.034,1.693],[0.031,1.699],[0.026,1.705],[0.021,1.709],[0.015,1.713],[0.008,1.715],[0.001,1.715],[-0.006,1.715],[-0.013,1.713],[-0.019,1.709],[-0.024,1.705],[-0.029,1.699],[-0.032,1.693],[-0.034,1.686],[-0.035,1.679],[-0.034,1.673],[-0.032,1.666],[-0.029,1.66],[-0.024,1.654],[-0.019,1.65],[-0.013,1.646],[-0.006,1.644],[0.001,1.644],[0.008,1.644],[0.015,1.646],[0.021,1.65],[0.026,1.654],[0.031,1.66],[0.034,1.666],[0.036,1.673]]],"aperture_large":[[[0.097,0.999],[0.095,1.018],[0.09,1.037],[0.081,1.053],[0.069,1.068],[0.054,1.08],[0.037,1.089],[0.019,1.095],[0,1.097],[-0.019,1.095],[-0.037,1.089],[-0.054,1.08],[-0.069,1.068],[-0.081,1.053],[-0.09,1.037],[-0.095,1.018],[-0.097,0.999],[-0.095,0.98],[-0.09,0.962],[-0.081,0.945],[-0.069,0.931],[-0.054,0.919],[-0.037,0.909],[-0.019,0.904],[0,0.902],[0.019,0.904],[0.037,0.909],[0.054,0.919],[0.069,0.931],[0.081,0.945],[0.09,0.962],[0.095,0.98]]],"aperture_ring":[[[0.065,1.679],[0.064,1.692],[0.06,1.704],[0.054,1.715],[0.046,1.724],[0.037,1.732],[0.025,1.738],[0.014,1.742],[0.001,1.743],[-0.011,1.742],[-0.023,1.738],[-0.034,1.732],[-0.044,1.724],[-0.052,1.715],[-0.058,1.704],[-0.061,1.692],[-0.063,1.679],[-0.061,1.667],[-0.058,1.655],[-0.052,1.644],[-0.044,1.634],[-0.034,1.627],[-0.023,1.621],[-0.011,1.617],[0.001,1.616],[0.014,1.617],[0.025,1.621],[0.037,1.627],[0.046,1.634],[0.054,1.644],[0.06,1.655],[0.064,1.667]]],"windage_screw":[[[-0.465,1.422],[0.507,1.422],[0.507,1.262],[-0.465,1.262]]],"knob_collar":[[[0.484,1.633],[0.493,1.633],[0.507,1.616],[0.507,1.068],[0.493,1.051],[0.484,1.051]]],"knob_grip":[[[0.507,1.573],[0.664,1.567],[0.713,1.541],[0.713,1.143],[0.664,1.117],[0.507,1.111]]],"flange_left":[[[-0.143,1.549],[-0.068,1.549],[-0.068,1.135],[-0.143,1.135]]],"flange_right":[[[0.07,1.549],[0.145,1.549],[0.145,1.135],[0.07,1.135]]],"traveller":[[[-0.068,1.476],[0.07,1.476],[0.07,1.208],[-0.068,1.208]]],"clamp_boss":[[[-0.586,0.465],[-0.667,0.443],[-0.667,0.052],[-0.586,0.03]]],"screw_head":[[[0.587,0.425],[0.669,0.425],[0.669,0.07],[0.587,0.07]]],"base":[[[-0.488,0.697],[-0.587,0.597],[-0.587,0.068],[-0.485,0],[-0.353,0],[-0.353,0.064],[-0.422,0.134],[-0.437,0.149],[-0.448,0.159],[-0.448,0.229],[-0.441,0.245],[-0.424,0.253],[0.424,0.253],[0.441,0.245],[0.448,0.229],[0.448,0.159],[0.437,0.149],[0.422,0.134],[0.353,0.064],[0.353,0],[0.485,0],[0.587,0.068],[0.587,0.597],[0.488,0.697]]],"knuckle_left":[[[-0.333,0.603],[-0.178,0.603],[-0.178,0.253],[-0.333,0.253]]],"knuckle_right":[[[0.178,0.603],[0.334,0.603],[0.334,0.253],[0.178,0.253]]],"spring":[[[-0.164,0.603],[0.166,0.603],[0.166,0.357],[-0.164,0.357]]],"rail_top":[[[-0.424,0.253],[0.424,0.253],[0.424,0.25],[-0.424,0.25]]]},"side":{"arm":[[[-0.669,0.465],[-0.669,0.517],[-0.673,0.527],[-0.673,0.533],[-0.669,0.536],[-0.669,1.177],[-0.673,1.3],[-0.679,1.4],[-0.687,1.467],[-0.687,1.481],[-0.691,1.498],[-0.691,1.513],[-0.696,1.547],[-0.701,1.603],[-0.715,1.708],[-0.72,1.756],[-0.73,1.823],[-0.741,1.849],[-0.749,1.859],[-0.767,1.876],[-0.784,1.885],[-1.009,1.947],[-1.025,1.949],[-1.051,1.947],[-1.068,1.939],[-1.086,1.921],[-1.095,1.903],[-1.102,1.868],[-1.102,0.531],[-1.097,0.528],[-1.102,0.518],[-1.102,0.474],[-1.096,0.43],[-1.094,0.427],[-1.094,0.422],[-1.085,0.396],[-1.076,0.377],[-1.063,0.356],[-1.043,0.331],[-1.014,0.306],[-0.974,0.283],[-0.945,0.273],[-0.936,0.272],[-0.934,0.269],[-0.902,0.265],[-0.871,0.265],[-0.839,0.269],[-0.805,0.279],[-0.764,0.301],[-0.738,0.322],[-0.709,0.355],[-0.692,0.383],[-0.676,0.424]]],"base":[[[0,0.099],[0,0.237],[-0.006,0.291],[-0.011,0.324],[-0.027,0.377],[-0.039,0.431],[-0.044,0.441],[-0.045,0.452],[-0.049,0.462],[-0.049,0.469],[-0.053,0.476],[-0.07,0.552],[-0.085,0.584],[-0.095,0.598],[-0.109,0.614],[-0.128,0.629],[-0.137,0.633],[-0.139,0.636],[-0.177,0.65],[-0.25,0.663],[-0.253,0.665],[-0.294,0.671],[-0.299,0.673],[-0.463,0.696],[-0.484,0.698],[-0.592,0.697],[-0.604,0.694],[-0.619,0.686],[-0.635,0.672],[-0.649,0.649],[-0.655,0.622],[-0.656,0.472],[-0.66,0.434],[-0.671,0.401],[-0.678,0.386],[-0.678,0.383],[-0.687,0.369],[-0.691,0.36],[-0.704,0.344],[-0.712,0.327],[-0.719,0.302],[-0.72,0.279],[-0.716,0.259],[-0.713,0.252],[-0.712,0.242],[-0.71,0.24],[-0.701,0.199],[-0.696,0.191],[-0.696,0.185],[-0.679,0.128],[-0.671,0.088],[-0.653,0.051],[-0.626,0.022],[-0.604,0.01],[-0.583,0.003],[-0.559,0],[-0.096,0],[-0.066,0.007],[-0.052,0.016],[-0.049,0.016],[-0.025,0.037],[-0.008,0.065]]],"hinge":[[[-1.066,0.481],[-1.063,0.517],[-1.053,0.551],[-1.036,0.582],[-1.013,0.609],[-0.986,0.632],[-0.955,0.649],[-0.921,0.659],[-0.885,0.662],[-0.85,0.659],[-0.816,0.649],[-0.785,0.632],[-0.757,0.609],[-0.735,0.582],[-0.718,0.551],[-0.708,0.517],[-0.704,0.481],[-0.708,0.446],[-0.718,0.412],[-0.735,0.381],[-0.757,0.353],[-0.785,0.331],[-0.816,0.314],[-0.85,0.304],[-0.885,0.3],[-0.921,0.304],[-0.955,0.314],[-0.986,0.331],[-1.013,0.353],[-1.036,0.381],[-1.053,0.412],[-1.063,0.446]]],"windage":[[[-1.068,1.343],[-1.065,1.378],[-1.054,1.412],[-1.038,1.443],[-1.015,1.471],[-0.987,1.493],[-0.956,1.51],[-0.922,1.521],[-0.887,1.524],[-0.851,1.521],[-0.817,1.51],[-0.786,1.493],[-0.758,1.471],[-0.736,1.443],[-0.719,1.412],[-0.709,1.378],[-0.705,1.343],[-0.709,1.307],[-0.719,1.273],[-0.736,1.242],[-0.758,1.214],[-0.786,1.192],[-0.817,1.175],[-0.851,1.165],[-0.887,1.161],[-0.922,1.165],[-0.956,1.175],[-0.987,1.192],[-1.015,1.214],[-1.038,1.242],[-1.054,1.273],[-1.065,1.307]]],"bolt":[[[-0.467,0.248],[-0.464,0.282],[-0.454,0.314],[-0.438,0.345],[-0.416,0.371],[-0.39,0.393],[-0.36,0.409],[-0.327,0.419],[-0.293,0.422],[-0.259,0.419],[-0.226,0.409],[-0.196,0.393],[-0.17,0.371],[-0.148,0.345],[-0.132,0.314],[-0.122,0.282],[-0.119,0.248],[-0.122,0.214],[-0.132,0.181],[-0.148,0.151],[-0.17,0.124],[-0.196,0.103],[-0.226,0.087],[-0.259,0.077],[-0.293,0.073],[-0.327,0.077],[-0.36,0.087],[-0.39,0.103],[-0.416,0.124],[-0.438,0.151],[-0.454,0.181],[-0.464,0.214]]],"hinge_pin":[[[-0.933,0.481],[-0.932,0.49],[-0.929,0.5],[-0.925,0.508],[-0.919,0.515],[-0.912,0.521],[-0.904,0.525],[-0.895,0.528],[-0.885,0.529],[-0.876,0.528],[-0.867,0.525],[-0.859,0.521],[-0.851,0.515],[-0.846,0.508],[-0.841,0.5],[-0.838,0.49],[-0.837,0.481],[-0.838,0.472],[-0.841,0.463],[-0.846,0.455],[-0.851,0.447],[-0.859,0.441],[-0.867,0.437],[-0.876,0.434],[-0.885,0.433],[-0.895,0.434],[-0.904,0.437],[-0.912,0.441],[-0.919,0.447],[-0.925,0.455],[-0.929,0.463],[-0.932,0.472]]],"plate":[[[-1.028,1.846],[-1.099,1.846],[-1.099,0.835],[-1.028,0.835]]],"knuckle":[[[-0.681,0.603],[-0.885,0.603],[-0.909,0.601],[-0.932,0.594],[-0.953,0.582],[-0.971,0.567],[-0.986,0.549],[-0.998,0.528],[-1.005,0.505],[-1.007,0.481],[-1.007,0.253],[-0.681,0.253]]]},"plan":{"base":[[[0,-0.508],[0,0.462],[-0.003,0.463],[-0.003,0.467],[-0.059,0.52],[-0.069,0.523],[-0.094,0.534],[-0.126,0.555],[-0.132,0.563],[-0.139,0.564],[-0.652,0.564],[-0.648,0.484],[-0.623,0.484],[-0.623,0.481],[-0.617,0.477],[-0.605,0.471],[-0.599,0.461],[-0.596,0.359],[-0.607,0.345],[-0.625,0.334],[-0.631,0.329],[-0.632,0.326],[-0.653,0.314],[-0.666,0.302],[-0.666,-0.51],[-0.674,-0.524],[-0.688,-0.542],[-0.689,-0.55],[-0.664,-0.604],[-0.654,-0.61],[-0.139,-0.61],[-0.132,-0.609],[-0.099,-0.582],[-0.069,-0.568],[-0.059,-0.566],[-0.008,-0.518],[-0.003,-0.513],[-0.003,-0.509]]],"latch":[[[-0.667,-0.395],[-0.664,-0.414],[-0.655,-0.431],[-0.641,-0.445],[-0.624,-0.453],[-0.605,-0.456],[-0.101,-0.456],[-0.082,-0.453],[-0.065,-0.445],[-0.051,-0.431],[-0.043,-0.414],[-0.04,-0.395],[-0.04,0.355],[-0.043,0.374],[-0.051,0.391],[-0.065,0.404],[-0.082,0.413],[-0.101,0.416],[-0.605,0.416],[-0.624,0.413],[-0.641,0.404],[-0.655,0.391],[-0.664,0.374],[-0.667,0.355]]]}},"placement":{"rear":{"plane":"zy","offset":{"y":"clamp_bottom_y"}},"side":{"plane":"xy","offset":{"x":"clamp_front_x","y":"clamp_bottom_y"}},"plan":{"plane":"xz","offset":{"x":"clamp_front_x"}}},"bounds":{"min":[-0.8341,-0.253,-0.667],"max":[0.343,1.696,0.713]},"volume_in3":0.882,"centroid":[-0.3163,0.4784,0.023],"shell":[-0.3894,0.581,0.0414],"area_in2":14.4321,"triangles":13602,"manifold":true,"rail_seat":{"x":[-0.377,0.343],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-0.759,-0.253,-0.667,0.343,0.527,0.669],[-0.776,0.527,-0.535,-0.311,0.916,0.713],[-0.834,0.916,-0.483,-0.253,1.306,0.713],[-0.759,1.306,-0.483,-0.351,1.696,0.679]],"slots":["body","hardware"]},"magpul-mbus-pro-front.folded":{"part":"magpul-mbus-pro-front","component":"folded","model":"magpul-mbus-pro-front.folded.glb","script":"magpul_mbus_pro_front.py","inputs":{"magpul-mbus-pro-front.knob_diameter":0.388,"magpul-mbus-pro-front.pivot_x":0.209,"magpul-mbus-pro-front.pivot_y":0.256,"magpul-mbus-pro-front.post_width_match":0.04,"magpul-mbus-pro-front.screw_hex":0.125,"magpul-mbus-pro-front.sight_line_above_rail":1.41,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{"side":[[-1.113,0.054],[-1.101,0.038],[-1.067,0.017],[-0.606,0.017],[-0.572,0.03],[-0.545,0.069],[-0.519,0.069],[-0.513,0.063],[-0.519,0.029],[-0.517,-0.166],[-0.504,-0.195],[-0.477,-0.211],[0.471,-0.213],[0.504,-0.199],[0.518,-0.175],[0.518,0.112],[0.51,0.137],[0.496,0.155],[0.306,0.345],[0.254,0.374],[0.194,0.383],[0.179,0.418],[0.158,0.416],[0.113,0.38],[-0.26,0.38],[-0.279,0.39],[-0.312,0.448],[-0.322,0.454],[-0.331,0.454],[-0.357,0.428],[-0.371,0.442],[-0.395,0.451],[-0.557,0.451],[-0.587,0.436],[-0.594,0.418],[-0.593,0.39],[-0.61,0.38],[-0.626,0.393],[-0.626,0.437],[-0.651,0.454],[-0.664,0.446],[-0.705,0.383],[-0.87,0.381],[-0.931,0.375],[-1.031,0.354],[-1.057,0.339],[-1.094,0.276]],"end":[[-0.65,0.113],[-0.65,0.026],[-0.585,0.026],[-0.578,0.019],[-0.578,-0.053],[-0.585,-0.06],[-0.65,-0.059],[-0.647,-0.159],[-0.624,-0.191],[-0.603,-0.202],[-0.562,-0.202],[-0.54,-0.182],[-0.49,-0.183],[-0.458,-0.211],[-0.438,-0.2],[-0.367,-0.2],[-0.351,-0.187],[-0.349,-0.176],[-0.4,-0.123],[-0.394,-0.118],[0.415,-0.118],[0.421,-0.125],[0.356,-0.191],[0.361,-0.206],[0.38,-0.213],[0.451,-0.213],[0.504,-0.165],[0.568,-0.16],[0.596,-0.132],[0.598,-0.087],[0.594,0.101],[0.564,0.126],[0.508,0.13],[0.313,0.361],[0.296,0.368],[0.223,0.368],[0.167,0.409],[0.121,0.43],[0.067,0.447],[0.002,0.455],[-0.055,0.45],[-0.123,0.431],[-0.184,0.401],[-0.228,0.368],[-0.3,0.368],[-0.318,0.361],[-0.479,0.169],[-0.535,0.169],[-0.548,0.158],[-0.573,0.169],[-0.605,0.166],[-0.635,0.145]],"plan":[[-1.113,0.287],[-1.097,0.262],[-1.059,0.237],[-0.773,0.17],[-0.751,0.15],[-0.743,0.129],[-0.743,0.089],[-0.752,0.081],[-0.803,0.082],[-0.829,0.064],[-0.881,0.046],[-1.01,0.037],[-1.009,-0.023],[-0.894,-0.031],[-0.855,-0.04],[-0.799,-0.068],[-0.75,-0.067],[-0.743,-0.073],[-0.745,-0.119],[-0.752,-0.137],[-0.774,-0.155],[-1.07,-0.227],[-1.113,-0.267],[-1.105,-0.3],[-1.09,-0.325],[-1.029,-0.354],[-0.981,-0.366],[-0.743,-0.337],[-0.528,-0.345],[-0.519,-0.354],[-0.519,-0.439],[-0.512,-0.454],[-0.486,-0.472],[-0.398,-0.498],[-0.388,-0.507],[-0.378,-0.549],[-0.394,-0.585],[-0.38,-0.62],[-0.358,-0.645],[-0.322,-0.656],[-0.084,-0.656],[-0.044,-0.644],[-0.023,-0.62],[-0.011,-0.585],[-0.015,-0.56],[-0.024,-0.549],[-0.009,-0.529],[0.006,-0.526],[0.011,-0.517],[0.01,-0.408],[0.016,-0.401],[0.025,-0.413],[0.026,-0.526],[0.05,-0.539],[0.343,-0.537],[0.437,-0.513],[0.495,-0.49],[0.507,-0.48],[0.517,-0.455],[0.518,-0.373],[0.518,0.446],[0.516,0.478],[0.496,0.504],[0.402,0.539],[0.33,0.553],[-0.029,0.553],[-0.049,0.563],[-0.053,0.587],[-0.078,0.617],[-0.132,0.623],[-0.322,0.62],[-0.348,0.589],[-0.353,0.542],[-0.365,0.528],[-0.417,0.522],[-0.503,0.484],[-0.519,0.453],[-0.519,0.376],[-0.527,0.36],[-0.755,0.352],[-0.976,0.381],[-1.013,0.374],[-1.086,0.343],[-1.105,0.315]]},"features":{"side":{"base":[[[-0.472,-0.212],[0.483,-0.212],[0.5,-0.204],[0.512,-0.193],[0.518,-0.179],[0.518,0.09],[0.515,0.111],[0.508,0.132],[0.495,0.151],[0.32,0.343],[0.303,0.358],[0.282,0.37],[0.261,0.379],[0.24,0.381],[0.113,0.381],[0.092,0.378],[0.073,0.369],[0.061,0.356],[0.05,0.332],[0.046,0.28],[0.046,0.237],[0.043,0.211],[0.034,0.195],[0.021,0.187],[0.003,0.184],[-0.404,0.184],[-0.43,0.176],[-0.451,0.161],[-0.467,0.145],[-0.477,0.127],[-0.493,0.1],[-0.511,0.069],[-0.517,0.048],[-0.517,-0.163],[-0.513,-0.185],[-0.503,-0.2],[-0.488,-0.209]]],"arm":[[[-1.112,0.069],[-1.111,0.111],[-1.109,0.153],[-1.106,0.195],[-1.102,0.237],[-1.097,0.269],[-1.089,0.295],[-1.077,0.32],[-1.06,0.339],[-1.039,0.352],[-1.01,0.362],[-0.973,0.37],[-0.931,0.377],[-0.889,0.381],[0.209,0.381],[0.257,0.371],[0.297,0.344],[0.324,0.304],[0.334,0.256],[0.324,0.209],[0.297,0.169],[0.257,0.141],[0.209,0.132],[0.166,0.139],[0.132,0.158],[0.108,0.184],[-0.404,0.184],[-0.435,0.174],[-0.525,0.069],[-0.546,0.045],[-0.562,0.031],[-0.578,0.022],[-0.593,0.018],[-1.058,0.018],[-1.079,0.023],[-1.097,0.035],[-1.108,0.05]]],"knob":[[[-0.593,0.451],[-0.359,0.451],[-0.359,0.062],[-0.593,0.062]]],"ridge_rear":[[[-0.712,0.381],[-0.655,0.452],[-0.644,0.452],[-0.627,0.431],[-0.624,0.381]]],"ridge_front":[[[-0.358,0.381],[-0.358,0.426],[-0.334,0.452],[-0.323,0.452],[-0.27,0.381]]],"tab":[[[0.119,0.381],[0.132,0.389],[0.154,0.415],[0.166,0.419],[0.179,0.419],[0.184,0.412],[0.187,0.385],[0.192,0.381]]],"pivot":[[[0.126,0.34],[0.293,0.34],[0.293,0.173],[0.126,0.173]]],"nut":[[[-0.351,0.137],[-0.049,0.137],[-0.049,-0.165],[-0.351,-0.165]]]},"end":{"channel":[[[0.44,-0.234],[0.44,-0.087],[0.346,0],[-0.346,0],[-0.443,-0.087],[-0.443,-0.234]]],"body":[[[0.537,-0.212],[0.54,0.071],[0.522,0.133],[0.293,0.363],[-0.293,0.363],[-0.522,0.133],[-0.537,0.071],[-0.537,-0.212]]],"ears_gap":[[[0.211,0.377],[-0.211,0.377],[-0.211,0.27],[0.211,0.27]]],"head":[[[-0.545,0.179],[-0.649,0.179],[-0.649,-0.205],[-0.545,-0.205]]],"head_slot":[[[-0.579,0.023],[-0.653,0.023],[-0.653,-0.068],[-0.579,-0.068]]],"nut":[[[0.598,0.124],[0.537,0.124],[0.537,-0.176],[0.598,-0.176]]],"bolt":[[[0.44,0.086],[-0.443,0.086],[-0.443,-0.114],[0.44,-0.114]]],"lip_right":[[[0.44,-0.114],[0.432,-0.114],[0.355,-0.19],[0.366,-0.207],[0.44,-0.211]]],"lip_left":[[[-0.443,-0.114],[-0.434,-0.114],[-0.348,-0.177],[-0.344,-0.19],[-0.356,-0.197],[-0.443,-0.197]]]},"plan":{"arm":[[[-1.112,-0.268],[-1.107,-0.296],[-1.095,-0.322],[-1.076,-0.335],[-1.031,-0.354],[-0.987,-0.365],[-0.942,-0.363],[-0.875,-0.352],[-0.786,-0.34],[-0.742,-0.337],[-0.653,-0.338],[-0.541,-0.344],[-0.43,-0.355],[-0.319,-0.369],[-0.207,-0.38],[-0.096,-0.387],[-0.007,-0.389],[0.01,-0.382],[0.029,-0.346],[0.044,-0.302],[0.051,-0.235],[0.057,-0.218],[0.305,-0.218],[0.344,-0.174],[0.344,0.174],[0.305,0.218],[0.057,0.218],[0.051,0.235],[0.044,0.302],[0.029,0.346],[0.01,0.382],[-0.007,0.389],[-0.096,0.387],[-0.207,0.38],[-0.319,0.369],[-0.43,0.355],[-0.541,0.344],[-0.653,0.338],[-0.742,0.337],[-0.786,0.34],[-0.875,0.352],[-0.942,0.363],[-0.987,0.365],[-1.031,0.354],[-1.076,0.335],[-1.095,0.322],[-1.107,0.296],[-1.112,0.268],[-1.098,0.246],[-1.053,0.22],[-0.987,0.204],[-0.875,0.176],[-0.809,0.159],[-0.775,0.148],[-0.758,0.129],[-0.747,0.101],[-0.744,0.068],[-0.744,-0.068],[-0.747,-0.101],[-0.758,-0.129],[-0.775,-0.148],[-0.809,-0.159],[-0.875,-0.176],[-0.987,-0.204],[-1.053,-0.22],[-1.098,-0.246]]],"window":[[[-0.625,-0.218],[-0.269,-0.218],[-0.269,0.218],[-0.625,0.218]]],"pocket":[[[-0.216,-0.224],[0.002,-0.224],[0.002,0.224],[-0.216,0.224]]],"post":[[[-1.011,-0.026],[-0.886,-0.026],[-0.803,-0.067],[-0.744,-0.067],[-0.744,0.068],[-0.803,0.068],[-0.886,0.03],[-1.011,0.03]]]}},"placement":{"side":{"plane":"xy","offset":{}},"end":{"plane":"zy","offset":{}},"plan":{"plane":"xz","offset":{}}},"bounds":{"min":[-1.112,-0.212,-0.649],"max":[0.518,0.4525,0.598]},"volume_in3":0.4819,"centroid":[-0.1641,0.1249,-0.0063],"shell":[-0.2017,0.1258,-0.0122],"area_in2":8.2569,"triangles":11578,"manifold":true,"rail_seat":{"x":[-0.517,0.518],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-1.112,0.018,-0.365,-0.786,0.382,0.365],[-0.786,-0.212,-0.537,-0.46,0.452,0.54],[-0.46,-0.212,-0.649,0.192,0.452,0.598],[0.192,-0.212,-0.537,0.518,0.382,0.54]],"slots":["body"]},"magpul-mbus-pro-front.up":{"part":"magpul-mbus-pro-front","component":"up","model":"magpul-mbus-pro-front.up.glb","script":"magpul_mbus_pro_front.py","inputs":{"magpul-mbus-pro-front.knob_diameter":0.388,"magpul-mbus-pro-front.pivot_x":0.209,"magpul-mbus-pro-front.pivot_y":0.256,"magpul-mbus-pro-front.post_width_match":0.04,"magpul-mbus-pro-front.screw_hex":0.125,"magpul-mbus-pro-front.sight_line_above_rail":1.41,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{"side":[[-1.113,0.054],[-1.101,0.038],[-1.067,0.017],[-0.606,0.017],[-0.572,0.03],[-0.545,0.069],[-0.519,0.069],[-0.513,0.063],[-0.519,0.029],[-0.517,-0.166],[-0.504,-0.195],[-0.477,-0.211],[0.471,-0.213],[0.504,-0.199],[0.518,-0.175],[0.518,0.112],[0.51,0.137],[0.496,0.155],[0.306,0.345],[0.254,0.374],[0.194,0.383],[0.179,0.418],[0.158,0.416],[0.113,0.38],[-0.26,0.38],[-0.279,0.39],[-0.312,0.448],[-0.322,0.454],[-0.331,0.454],[-0.357,0.428],[-0.371,0.442],[-0.395,0.451],[-0.557,0.451],[-0.587,0.436],[-0.594,0.418],[-0.593,0.39],[-0.61,0.38],[-0.626,0.393],[-0.626,0.437],[-0.651,0.454],[-0.664,0.446],[-0.705,0.383],[-0.87,0.381],[-0.931,0.375],[-1.031,0.354],[-1.057,0.339],[-1.094,0.276]],"end":[[-0.65,0.113],[-0.65,0.026],[-0.585,0.026],[-0.578,0.019],[-0.578,-0.053],[-0.585,-0.06],[-0.65,-0.059],[-0.647,-0.159],[-0.624,-0.191],[-0.603,-0.202],[-0.562,-0.202],[-0.54,-0.182],[-0.49,-0.183],[-0.458,-0.211],[-0.438,-0.2],[-0.367,-0.2],[-0.351,-0.187],[-0.349,-0.176],[-0.4,-0.123],[-0.394,-0.118],[0.415,-0.118],[0.421,-0.125],[0.356,-0.191],[0.361,-0.206],[0.38,-0.213],[0.451,-0.213],[0.504,-0.165],[0.568,-0.16],[0.596,-0.132],[0.598,-0.087],[0.594,0.101],[0.564,0.126],[0.508,0.13],[0.313,0.361],[0.296,0.368],[0.223,0.368],[0.167,0.409],[0.121,0.43],[0.067,0.447],[0.002,0.455],[-0.055,0.45],[-0.123,0.431],[-0.184,0.401],[-0.228,0.368],[-0.3,0.368],[-0.318,0.361],[-0.479,0.169],[-0.535,0.169],[-0.548,0.158],[-0.573,0.169],[-0.605,0.166],[-0.635,0.145]],"plan":[[-1.113,0.287],[-1.097,0.262],[-1.059,0.237],[-0.773,0.17],[-0.751,0.15],[-0.743,0.129],[-0.743,0.089],[-0.752,0.081],[-0.803,0.082],[-0.829,0.064],[-0.881,0.046],[-1.01,0.037],[-1.009,-0.023],[-0.894,-0.031],[-0.855,-0.04],[-0.799,-0.068],[-0.75,-0.067],[-0.743,-0.073],[-0.745,-0.119],[-0.752,-0.137],[-0.774,-0.155],[-1.07,-0.227],[-1.113,-0.267],[-1.105,-0.3],[-1.09,-0.325],[-1.029,-0.354],[-0.981,-0.366],[-0.743,-0.337],[-0.528,-0.345],[-0.519,-0.354],[-0.519,-0.439],[-0.512,-0.454],[-0.486,-0.472],[-0.398,-0.498],[-0.388,-0.507],[-0.378,-0.549],[-0.394,-0.585],[-0.38,-0.62],[-0.358,-0.645],[-0.322,-0.656],[-0.084,-0.656],[-0.044,-0.644],[-0.023,-0.62],[-0.011,-0.585],[-0.015,-0.56],[-0.024,-0.549],[-0.009,-0.529],[0.006,-0.526],[0.011,-0.517],[0.01,-0.408],[0.016,-0.401],[0.025,-0.413],[0.026,-0.526],[0.05,-0.539],[0.343,-0.537],[0.437,-0.513],[0.495,-0.49],[0.507,-0.48],[0.517,-0.455],[0.518,-0.373],[0.518,0.446],[0.516,0.478],[0.496,0.504],[0.402,0.539],[0.33,0.553],[-0.029,0.553],[-0.049,0.563],[-0.053,0.587],[-0.078,0.617],[-0.132,0.623],[-0.322,0.62],[-0.348,0.589],[-0.353,0.542],[-0.365,0.528],[-0.417,0.522],[-0.503,0.484],[-0.519,0.453],[-0.519,0.376],[-0.527,0.36],[-0.755,0.352],[-0.976,0.381],[-1.013,0.374],[-1.086,0.343],[-1.105,0.315]]},"features":{"side":{"base":[[[-0.472,-0.212],[0.483,-0.212],[0.5,-0.204],[0.512,-0.193],[0.518,-0.179],[0.518,0.09],[0.515,0.111],[0.508,0.132],[0.495,0.151],[0.32,0.343],[0.303,0.358],[0.282,0.37],[0.261,0.379],[0.24,0.381],[0.113,0.381],[0.092,0.378],[0.073,0.369],[0.061,0.356],[0.05,0.332],[0.046,0.28],[0.046,0.237],[0.043,0.211],[0.034,0.195],[0.021,0.187],[0.003,0.184],[-0.404,0.184],[-0.43,0.176],[-0.451,0.161],[-0.467,0.145],[-0.477,0.127],[-0.493,0.1],[-0.511,0.069],[-0.517,0.048],[-0.517,-0.163],[-0.513,-0.185],[-0.503,-0.2],[-0.488,-0.209]]],"arm":[[[-1.112,0.069],[-1.111,0.111],[-1.109,0.153],[-1.106,0.195],[-1.102,0.237],[-1.097,0.269],[-1.089,0.295],[-1.077,0.32],[-1.06,0.339],[-1.039,0.352],[-1.01,0.362],[-0.973,0.37],[-0.931,0.377],[-0.889,0.381],[0.209,0.381],[0.257,0.371],[0.297,0.344],[0.324,0.304],[0.334,0.256],[0.324,0.209],[0.297,0.169],[0.257,0.141],[0.209,0.132],[0.166,0.139],[0.132,0.158],[0.108,0.184],[-0.404,0.184],[-0.435,0.174],[-0.525,0.069],[-0.546,0.045],[-0.562,0.031],[-0.578,0.022],[-0.593,0.018],[-1.058,0.018],[-1.079,0.023],[-1.097,0.035],[-1.108,0.05]]],"knob":[[[-0.593,0.451],[-0.359,0.451],[-0.359,0.062],[-0.593,0.062]]],"ridge_rear":[[[-0.712,0.381],[-0.655,0.452],[-0.644,0.452],[-0.627,0.431],[-0.624,0.381]]],"ridge_front":[[[-0.358,0.381],[-0.358,0.426],[-0.334,0.452],[-0.323,0.452],[-0.27,0.381]]],"tab":[[[0.119,0.381],[0.132,0.389],[0.154,0.415],[0.166,0.419],[0.179,0.419],[0.184,0.412],[0.187,0.385],[0.192,0.381]]],"pivot":[[[0.126,0.34],[0.293,0.34],[0.293,0.173],[0.126,0.173]]],"nut":[[[-0.351,0.137],[-0.049,0.137],[-0.049,-0.165],[-0.351,-0.165]]]},"end":{"channel":[[[0.44,-0.234],[0.44,-0.087],[0.346,0],[-0.346,0],[-0.443,-0.087],[-0.443,-0.234]]],"body":[[[0.537,-0.212],[0.54,0.071],[0.522,0.133],[0.293,0.363],[-0.293,0.363],[-0.522,0.133],[-0.537,0.071],[-0.537,-0.212]]],"ears_gap":[[[0.211,0.377],[-0.211,0.377],[-0.211,0.27],[0.211,0.27]]],"head":[[[-0.545,0.179],[-0.649,0.179],[-0.649,-0.205],[-0.545,-0.205]]],"head_slot":[[[-0.579,0.023],[-0.653,0.023],[-0.653,-0.068],[-0.579,-0.068]]],"nut":[[[0.598,0.124],[0.537,0.124],[0.537,-0.176],[0.598,-0.176]]],"bolt":[[[0.44,0.086],[-0.443,0.086],[-0.443,-0.114],[0.44,-0.114]]],"lip_right":[[[0.44,-0.114],[0.432,-0.114],[0.355,-0.19],[0.366,-0.207],[0.44,-0.211]]],"lip_left":[[[-0.443,-0.114],[-0.434,-0.114],[-0.348,-0.177],[-0.344,-0.19],[-0.356,-0.197],[-0.443,-0.197]]]},"plan":{"arm":[[[-1.112,-0.268],[-1.107,-0.296],[-1.095,-0.322],[-1.076,-0.335],[-1.031,-0.354],[-0.987,-0.365],[-0.942,-0.363],[-0.875,-0.352],[-0.786,-0.34],[-0.742,-0.337],[-0.653,-0.338],[-0.541,-0.344],[-0.43,-0.355],[-0.319,-0.369],[-0.207,-0.38],[-0.096,-0.387],[-0.007,-0.389],[0.01,-0.382],[0.029,-0.346],[0.044,-0.302],[0.051,-0.235],[0.057,-0.218],[0.305,-0.218],[0.344,-0.174],[0.344,0.174],[0.305,0.218],[0.057,0.218],[0.051,0.235],[0.044,0.302],[0.029,0.346],[0.01,0.382],[-0.007,0.389],[-0.096,0.387],[-0.207,0.38],[-0.319,0.369],[-0.43,0.355],[-0.541,0.344],[-0.653,0.338],[-0.742,0.337],[-0.786,0.34],[-0.875,0.352],[-0.942,0.363],[-0.987,0.365],[-1.031,0.354],[-1.076,0.335],[-1.095,0.322],[-1.107,0.296],[-1.112,0.268],[-1.098,0.246],[-1.053,0.22],[-0.987,0.204],[-0.875,0.176],[-0.809,0.159],[-0.775,0.148],[-0.758,0.129],[-0.747,0.101],[-0.744,0.068],[-0.744,-0.068],[-0.747,-0.101],[-0.758,-0.129],[-0.775,-0.148],[-0.809,-0.159],[-0.875,-0.176],[-0.987,-0.204],[-1.053,-0.22],[-1.098,-0.246]]],"window":[[[-0.625,-0.218],[-0.269,-0.218],[-0.269,0.218],[-0.625,0.218]]],"pocket":[[[-0.216,-0.224],[0.002,-0.224],[0.002,0.224],[-0.216,0.224]]],"post":[[[-1.011,-0.026],[-0.886,-0.026],[-0.803,-0.067],[-0.744,-0.067],[-0.744,0.068],[-0.803,0.068],[-0.886,0.03],[-1.011,0.03]]]}},"placement":{"side":{"plane":"xy","offset":{}},"end":{"plane":"zy","offset":{}},"plan":{"plane":"xz","offset":{}}},"bounds":{"min":[-0.517,-0.212,-0.649],"max":[0.518,1.577,0.598]},"volume_in3":0.4819,"centroid":[0.0895,0.3916,-0.0063],"shell":[0.0944,0.4335,-0.0121],"area_in2":8.3388,"triangles":11424,"manifold":true,"rail_seat":{"x":[-0.517,0.518],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-0.517,-0.212,-0.649,0.518,0.146,0.598],[-0.466,0.146,-0.649,0.499,0.504,0.509],[-0.029,0.504,-0.388,0.405,1.219,0.388],[-0.029,1.219,-0.365,0.334,1.577,0.365]],"slots":["body"]},"magpul-mbus-pro-rear.folded":{"part":"magpul-mbus-pro-rear","component":"folded","model":"magpul-mbus-pro-rear.folded.glb","script":"magpul_mbus_pro_rear.py","inputs":{"magpul-mbus-pro-rear.clamp_bottom_y":-0.211,"magpul-mbus-pro-rear.clamp_length":0.819,"magpul-mbus-pro-rear.front_x":0.409,"magpul-mbus-pro-rear.hinge_above_rail":0.187,"magpul-mbus-pro-rear.hinge_behind_front":0.654,"magpul-mbus-pro-rear.knob_face_z":0.74,"magpul-mbus-pro-rear.knob_lobes":10,"magpul-mbus-pro-rear.large_aperture_d":0.19,"magpul-mbus-pro-rear.length":2.1,"magpul-mbus-pro-rear.relief_depth":0.03,"magpul-mbus-pro-rear.sight_line_above_rail":1.42,"magpul-mbus-pro-rear.small_aperture_d":0.07,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{"side":[[-2.1,0.229],[-2.094,0.224],[-1.965,0.223],[-0.836,0.224],[-0.818,0.211],[-0.818,0.037],[-0.801,0.011],[-0.782,0.001],[-0.041,0],[-0.015,0.015],[-0.001,0.047],[0,0.268],[-0.006,0.298],[-0.018,0.321],[-0.211,0.514],[-0.238,0.531],[-0.279,0.544],[-0.456,0.544],[-0.477,0.565],[-0.492,0.569],[-0.501,0.562],[-0.533,0.584],[-0.549,0.601],[-0.55,0.619],[-0.569,0.628],[-0.61,0.638],[-0.631,0.621],[-0.679,0.621],[-0.696,0.637],[-0.705,0.638],[-0.758,0.62],[-0.769,0.594],[-0.783,0.58],[-0.792,0.577],[-0.804,0.587],[-0.826,0.587],[-0.859,0.548],[-1.726,0.552],[-1.833,0.541],[-2.007,0.514],[-2.041,0.5],[-2.072,0.465],[-2.093,0.326]],"plan":[[-2.1,-0.641],[-2.1,-0.84],[-2.087,-0.913],[-2.041,-0.983],[-2.016,-1.008],[-1.989,-1.023],[-1.955,-1.033],[-1.92,-1.033],[-1.701,-1.019],[-1.605,-1.019],[-1.259,-1.084],[-1.246,-1.095],[-1.237,-1.089],[-1.037,-1.13],[-0.865,-1.135],[-0.837,-1.119],[-0.831,-1.126],[-0.831,-1.194],[-0.803,-1.252],[-0.8,-1.294],[-0.782,-1.312],[-0.518,-1.314],[-0.469,-1.322],[-0.468,-1.271],[-0.448,-1.257],[-0.422,-1.291],[-0.442,-1.294],[-0.442,-1.33],[-0.426,-1.364],[-0.403,-1.388],[-0.375,-1.397],[-0.13,-1.397],[-0.103,-1.389],[-0.082,-1.368],[-0.057,-1.325],[-0.072,-1.294],[-0.083,-1.291],[-0.074,-1.281],[-0.073,-1.238],[-0.055,-1.22],[-0.015,-1.206],[-0.003,-1.193],[0,-1.171],[0,-0.296],[-0.004,-0.274],[-0.02,-0.258],[-0.085,-0.236],[-0.104,-0.217],[-0.107,-0.191],[-0.125,-0.171],[-0.131,-0.176],[-0.166,-0.176],[-0.184,-0.16],[-0.32,-0.16],[-0.339,-0.176],[-0.365,-0.176],[-0.37,-0.171],[-0.396,-0.187],[-0.414,-0.169],[-0.414,-0.041],[-0.454,0],[-0.856,0],[-0.866,-0.005],[-0.895,-0.036],[-0.898,-0.049],[-0.898,-0.235],[-0.892,-0.251],[-0.867,-0.274],[-0.87,-0.327],[-0.891,-0.347],[-1.001,-0.346],[-1.124,-0.369],[-1.134,-0.37],[-1.141,-0.363],[-1.167,-0.378],[-1.592,-0.461],[-1.723,-0.461],[-1.925,-0.448],[-1.973,-0.451],[-2.022,-0.478],[-2.075,-0.546],[-2.089,-0.575]],"bottom":[[-2.1,-0.64],[-2.1,-0.84],[-2.091,-0.899],[-2.078,-0.93],[-2.024,-1.002],[-1.967,-1.032],[-1.864,-1.032],[-1.656,-1.018],[-1.591,-1.021],[-1.037,-1.132],[-0.867,-1.137],[-0.85,-1.132],[-0.817,-1.165],[-0.817,-1.216],[-0.797,-1.244],[-0.797,-1.278],[-0.804,-1.292],[-0.78,-1.316],[-0.529,-1.316],[-0.483,-1.271],[-0.469,-1.269],[-0.435,-1.301],[-0.443,-1.328],[-0.42,-1.372],[-0.392,-1.395],[-0.363,-1.4],[-0.137,-1.4],[-0.102,-1.391],[-0.078,-1.367],[-0.065,-1.33],[-0.07,-1.305],[-0.08,-1.293],[-0.072,-1.277],[-0.074,-1.253],[-0.037,-1.216],[-0.009,-1.206],[0,-1.185],[0,-0.293],[-0.007,-0.268],[-0.07,-0.242],[-0.103,-0.209],[-0.103,-0.199],[-0.116,-0.182],[-0.16,-0.177],[-0.176,-0.161],[-0.316,-0.16],[-0.337,-0.177],[-0.379,-0.18],[-0.412,-0.147],[-0.413,-0.041],[-0.444,-0.005],[-0.456,0],[-0.847,0],[-0.864,-0.007],[-0.889,-0.032],[-0.898,-0.051],[-0.897,-0.234],[-0.89,-0.252],[-0.866,-0.278],[-0.868,-0.316],[-0.901,-0.349],[-0.912,-0.343],[-0.919,-0.348],[-0.973,-0.348],[-0.981,-0.343],[-1.041,-0.352],[-1.403,-0.425],[-1.439,-0.421],[-1.457,-0.434],[-1.484,-0.441],[-1.616,-0.464],[-1.919,-0.449],[-1.954,-0.449],[-1.989,-0.459],[-2.019,-0.478],[-2.087,-0.549],[-2.079,-0.559],[-2.091,-0.586]],"front":[[-1.397,0.057],[-1.366,0.021],[-1.344,0.01],[-1.303,0.011],[-1.28,0.028],[-1.27,0.023],[-1.211,0.023],[-1.193,0.004],[-1.182,0.002],[-1.169,0.015],[-1.105,0.014],[-1.08,0.029],[-1.082,0.042],[-1.125,0.084],[-1.116,0.093],[-0.411,0.092],[-0.39,0.119],[-0.368,0.098],[-0.349,0.123],[-0.321,0.087],[-0.371,0.033],[-0.37,0.008],[-0.363,0],[-0.29,0.002],[-0.239,0.046],[-0.194,0.047],[-0.178,0.062],[-0.177,0.107],[-0.159,0.124],[-0.159,0.15],[-0.15,0.159],[-0.046,0.161],[-0.011,0.183],[0,0.206],[-0.003,0.604],[-0.034,0.631],[-0.052,0.636],[-0.217,0.635],[-0.236,0.642],[-0.275,0.61],[-0.347,0.612],[-0.36,0.607],[-0.392,0.565],[-0.416,0.561],[-0.438,0.541],[-0.584,0.544],[-0.607,0.579],[-0.619,0.582],[-0.724,0.582],[-0.738,0.567],[-0.749,0.582],[-0.862,0.582],[-0.892,0.544],[-0.906,0.541],[-1.036,0.541],[-1.057,0.561],[-1.066,0.562],[-1.189,0.561],[-1.212,0.548],[-1.29,0.548],[-1.309,0.528],[-1.309,0.387],[-1.334,0.384],[-1.366,0.366],[-1.389,0.332],[-1.392,0.235],[-1.379,0.212],[-1.376,0.185],[-1.392,0.151],[-1.392,0.075]]},"features":{"side":{"knob":[[[-0.409,0.642],[-0.409,0.153],[-0.899,0.153],[-0.899,0.642]]],"knob_root":[[[-0.428,0.624],[-0.428,0.17],[-0.881,0.17],[-0.881,0.624]]],"knob_face":[[[-0.459,0.594],[-0.459,0.202],[-0.85,0.202],[-0.85,0.594]]],"knob_hub":[[[-0.588,0.465],[-0.588,0.332],[-0.721,0.332],[-0.721,0.465]]],"boss":[[[-0.07,0.349],[-0.07,0.013],[-0.405,0.013],[-0.405,0.349]]],"boss_bore":[[[-0.103,0.317],[-0.103,0.046],[-0.372,0.046],[-0.372,0.317]]],"screw_end":[[[-0.158,0.26],[-0.158,0.103],[-0.317,0.103],[-0.317,0.26]]],"base":[[[0.001,0.544],[0.001,-0.001],[-0.819,-0.001],[-0.819,0.544]]],"arm_pin":[[[-1.56,0.502],[-1.56,0.42],[-1.643,0.42],[-1.643,0.502]]]},"plan":{"arm":[[[-0.83,-1.104],[-0.841,-1.124],[-0.862,-1.134],[-0.979,-1.135],[-1.037,-1.131],[-1.179,-1.101],[-1.237,-1.089],[-1.527,-1.035],[-1.565,-1.024],[-1.605,-1.019],[-1.701,-1.019],[-1.92,-1.032],[-1.955,-1.032],[-1.981,-1.027],[-2.011,-1.013],[-2.039,-0.987],[-2.086,-0.914],[-2.101,-0.84],[-2.101,-0.641],[-2.086,-0.566],[-2.039,-0.494],[-2.011,-0.468],[-1.981,-0.454],[-1.955,-0.448],[-1.92,-0.448],[-1.701,-0.461],[-1.605,-0.461],[-1.565,-0.457],[-1.527,-0.446],[-1.237,-0.391],[-1.179,-0.379],[-1.037,-0.35],[-0.979,-0.345],[-0.862,-0.346],[-0.841,-0.356],[-0.83,-0.377]]],"knuckle":[[[-0.509,-0.923],[-0.509,-0.555],[-0.805,-0.555],[-0.805,-0.923]]],"index_rib":[[[-0.769,-0.897],[-0.769,-0.583],[-0.853,-0.583],[-0.853,-0.897]]],"shaft":[[[-0.571,-1.057],[-0.571,-0.422],[-0.746,-0.422],[-0.746,-1.057]]],"ear_right":[[[-0.444,-0.422],[-0.444,-0.271],[-0.871,-0.271],[-0.871,-0.422]]],"ear_left":[[[-0.495,-1.214],[-0.495,-1.057],[-0.819,-1.057],[-0.819,-1.214]]],"cap":[[[-0.512,-1.314],[-0.512,-1.214],[-0.8,-1.214],[-0.8,-1.314]]],"knob":[[[-0.412,-0.261],[-0.412,0.001],[-0.899,0.001],[-0.899,-0.261]]],"bolt_head":[[[-0.055,-1.398],[-0.055,-1.297],[-0.439,-1.297],[-0.439,-1.398]]],"clamp_bar":[[[-0.001,-1.297],[-0.001,-1.175],[-0.445,-1.175],[-0.445,-1.297]]],"body":[[[-0.001,-1.175],[-0.001,-0.176],[-0.822,-0.176],[-0.822,-1.175]]],"boss":[[[-0.125,-0.176],[-0.125,-0.158],[-0.37,-0.158],[-0.37,-0.176]]],"slot":[[[-0.495,-1.057],[-0.495,-0.422],[-0.827,-0.422],[-0.827,-1.057]]],"top_pocket":[[[-0.194,-0.983],[-0.194,-0.497],[-0.417,-0.497],[-0.417,-0.983]]],"ticks":[[[-0.41,-0.871],[-0.41,-0.858],[-0.483,-0.858],[-0.483,-0.871]],[[-0.41,-0.746],[-0.41,-0.734],[-0.483,-0.734],[-0.483,-0.746]],[[-0.41,-0.621],[-0.41,-0.609],[-0.483,-0.609],[-0.483,-0.621]],[[-0.442,-0.808],[-0.442,-0.795],[-0.481,-0.795],[-0.481,-0.808]],[[-0.442,-0.686],[-0.442,-0.672],[-0.481,-0.672],[-0.481,-0.686]]],"logo_panel":[[[-0.965,-0.964],[-0.923,-0.925],[-0.923,-0.555],[-0.965,-0.517],[-1.337,-0.588],[-1.375,-0.619],[-1.375,-0.862],[-1.337,-0.892]]],"window":[[[-1.441,-0.856],[-1.441,-0.624],[-1.687,-0.624],[-1.687,-0.608],[-2.064,-0.608],[-2.064,-0.873],[-1.687,-0.873],[-1.687,-0.856]]],"aperture":[[[-1.849,-0.775],[-1.849,-0.704],[-1.92,-0.704],[-1.92,-0.775]]],"aperture_sink":[[[-1.807,-0.818],[-1.807,-0.663],[-1.963,-0.663],[-1.963,-0.818]]]},"bottom":{"aperture":[[[-1.92,-0.777],[-1.92,-0.706],[-1.848,-0.706],[-1.848,-0.777]]],"aperture_bore":[[[-1.976,-0.834],[-1.976,-0.65],[-1.792,-0.65],[-1.792,-0.834]]],"pad":[[[-2.061,-0.955],[-2.061,-0.527],[-1.687,-0.527],[-1.687,-0.955]]],"rib_pockets":[[[-1.599,-0.905],[-1.599,-0.578],[-1.302,-0.683],[-1.28,-0.706],[-1.28,-0.777],[-1.302,-0.8]],[[-1.181,-0.777],[-1.181,-0.706],[-1.132,-0.686],[-0.88,-0.632],[-0.828,-0.658],[-0.813,-0.672],[-0.813,-0.811],[-0.828,-0.825],[-0.88,-0.851],[-1.132,-0.797]],[[-1.462,-0.95],[-1.462,-0.931],[-1.251,-0.866],[-1.233,-0.866],[-0.923,-0.92],[-0.923,-1.053],[-0.941,-1.065]],[[-1.462,-0.533],[-1.462,-0.552],[-1.251,-0.617],[-1.233,-0.617],[-0.923,-0.563],[-0.923,-0.43],[-0.941,-0.418]]],"screw":[[[-0.351,-1.085],[-0.351,-0.392],[-0.15,-0.392],[-0.15,-1.085]]],"knuckle":[[[-0.754,-0.931],[-0.754,-0.563],[-0.497,-0.563],[-0.497,-0.931]]]},"front":{"rail":[[[-0.299,0.213],[-1.164,0.213],[-1.164,0.092],[-0.299,0.092]]],"body":[[[-0.421,0.544],[-1.057,0.544],[-1.202,0.386],[-1.202,0.213],[-0.398,0.213],[-0.299,0.125],[-0.366,0.045],[-0.368,0.01],[-0.36,0.003],[-0.279,0.003],[-0.253,0.044],[-0.197,0.047],[-0.178,0.066],[-0.176,0.318],[-0.188,0.336],[-0.221,0.342],[-0.27,0.392]]],"clamp_bar":[[[-1.202,0.38],[-1.284,0.38],[-1.292,0.371],[-1.292,0.032],[-1.284,0.023],[-1.195,0.023],[-1.182,0.015],[-1.097,0.015],[-1.08,0.032],[-1.164,0.125],[-1.164,0.195],[-1.13,0.229],[-1.202,0.229]]],"knob":[[[0.001,0.638],[-0.26,0.638],[-0.26,0.161],[0.001,0.161]]],"bolt_head":[[[-1.292,0.391],[-1.398,0.391],[-1.398,0.006],[-1.292,0.006]]],"head_slot":[[[-1.323,0.234],[-1.398,0.234],[-1.398,0.152],[-1.323,0.152]]],"ear_right":[[[-0.27,0.612],[-0.365,0.612],[-0.365,0.187],[-0.27,0.187]]],"ear_left":[[[-1.056,0.562],[-1.208,0.562],[-1.208,0.237],[-1.056,0.237]]],"cap":[[[-1.208,0.549],[-1.309,0.549],[-1.309,0.25],[-1.208,0.25]]],"index_rib":[[[-0.595,0.583],[-0.886,0.583],[-0.886,0.544],[-0.595,0.544]]],"screw_end":[[[-0.158,0.267],[-0.176,0.267],[-0.176,0.121],[-0.158,0.121]]]}},"placement":{"side":{"plane":"xy","offset":{"x":"front_x","y":"clamp_bottom_y"}},"plan":{"plane":"xz","offset":{"x":"front_x","y":"knob_face_z"}},"bottom":{"plane":"xz","offset":{"x":"front_x","y":"knob_face_z"}},"front":{"plane":"zy","offset":{"x":"knob_face_z","y":"clamp_bottom_y"}}},"bounds":{"min":[-1.6909,-0.208,-0.658],"max":[0.409,0.4282,0.75]},"volume_in3":0.6521,"centroid":[-0.3773,0.1354,0.0607],"shell":[-0.3189,0.1258,0.06],"area_in2":12.1887,"triangles":8252,"manifold":true,"rail_seat":{"x":[-0.41,0.409],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-1.691,0.012,-0.319,-0.991,0.341,0.318],[-0.991,0.012,-0.388,-0.641,0.34,0.387],[-0.641,-0.208,-0.574,-0.291,0.427,0.75],[-0.291,-0.208,-0.658,0.059,0.428,0.75],[0.059,-0.208,-0.658,0.409,0.333,0.582]],"slots":["body"]},"magpul-mbus-pro-rear.up":{"part":"magpul-mbus-pro-rear","component":"up","model":"magpul-mbus-pro-rear.up.glb","script":"magpul_mbus_pro_rear.py","inputs":{"magpul-mbus-pro-rear.clamp_bottom_y":-0.211,"magpul-mbus-pro-rear.clamp_length":0.819,"magpul-mbus-pro-rear.front_x":0.409,"magpul-mbus-pro-rear.height_up":1.633,"magpul-mbus-pro-rear.hinge_above_rail":0.187,"magpul-mbus-pro-rear.hinge_behind_front":0.654,"magpul-mbus-pro-rear.knob_face_z":0.74,"magpul-mbus-pro-rear.knob_lobes":10,"magpul-mbus-pro-rear.large_aperture_d":0.19,"magpul-mbus-pro-rear.length":2.1,"magpul-mbus-pro-rear.relief_depth":0.03,"magpul-mbus-pro-rear.sight_line_above_rail":1.42,"magpul-mbus-pro-rear.small_aperture_d":0.07,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{"side":[[-2.1,0.229],[-2.094,0.224],[-1.965,0.223],[-0.836,0.224],[-0.818,0.211],[-0.818,0.037],[-0.801,0.011],[-0.782,0.001],[-0.041,0],[-0.015,0.015],[-0.001,0.047],[0,0.268],[-0.006,0.298],[-0.018,0.321],[-0.211,0.514],[-0.238,0.531],[-0.279,0.544],[-0.456,0.544],[-0.477,0.565],[-0.492,0.569],[-0.501,0.562],[-0.533,0.584],[-0.549,0.601],[-0.55,0.619],[-0.569,0.628],[-0.61,0.638],[-0.631,0.621],[-0.679,0.621],[-0.696,0.637],[-0.705,0.638],[-0.758,0.62],[-0.769,0.594],[-0.783,0.58],[-0.792,0.577],[-0.804,0.587],[-0.826,0.587],[-0.859,0.548],[-1.726,0.552],[-1.833,0.541],[-2.007,0.514],[-2.041,0.5],[-2.072,0.465],[-2.093,0.326]],"plan":[[-2.1,-0.641],[-2.1,-0.84],[-2.087,-0.913],[-2.041,-0.983],[-2.016,-1.008],[-1.989,-1.023],[-1.955,-1.033],[-1.92,-1.033],[-1.701,-1.019],[-1.605,-1.019],[-1.259,-1.084],[-1.246,-1.095],[-1.237,-1.089],[-1.037,-1.13],[-0.865,-1.135],[-0.837,-1.119],[-0.831,-1.126],[-0.831,-1.194],[-0.803,-1.252],[-0.8,-1.294],[-0.782,-1.312],[-0.518,-1.314],[-0.469,-1.322],[-0.468,-1.271],[-0.448,-1.257],[-0.422,-1.291],[-0.442,-1.294],[-0.442,-1.33],[-0.426,-1.364],[-0.403,-1.388],[-0.375,-1.397],[-0.13,-1.397],[-0.103,-1.389],[-0.082,-1.368],[-0.057,-1.325],[-0.072,-1.294],[-0.083,-1.291],[-0.074,-1.281],[-0.073,-1.238],[-0.055,-1.22],[-0.015,-1.206],[-0.003,-1.193],[0,-1.171],[0,-0.296],[-0.004,-0.274],[-0.02,-0.258],[-0.085,-0.236],[-0.104,-0.217],[-0.107,-0.191],[-0.125,-0.171],[-0.131,-0.176],[-0.166,-0.176],[-0.184,-0.16],[-0.32,-0.16],[-0.339,-0.176],[-0.365,-0.176],[-0.37,-0.171],[-0.396,-0.187],[-0.414,-0.169],[-0.414,-0.041],[-0.454,0],[-0.856,0],[-0.866,-0.005],[-0.895,-0.036],[-0.898,-0.049],[-0.898,-0.235],[-0.892,-0.251],[-0.867,-0.274],[-0.87,-0.327],[-0.891,-0.347],[-1.001,-0.346],[-1.124,-0.369],[-1.134,-0.37],[-1.141,-0.363],[-1.167,-0.378],[-1.592,-0.461],[-1.723,-0.461],[-1.925,-0.448],[-1.973,-0.451],[-2.022,-0.478],[-2.075,-0.546],[-2.089,-0.575]],"bottom":[[-2.1,-0.64],[-2.1,-0.84],[-2.091,-0.899],[-2.078,-0.93],[-2.024,-1.002],[-1.967,-1.032],[-1.864,-1.032],[-1.656,-1.018],[-1.591,-1.021],[-1.037,-1.132],[-0.867,-1.137],[-0.85,-1.132],[-0.817,-1.165],[-0.817,-1.216],[-0.797,-1.244],[-0.797,-1.278],[-0.804,-1.292],[-0.78,-1.316],[-0.529,-1.316],[-0.483,-1.271],[-0.469,-1.269],[-0.435,-1.301],[-0.443,-1.328],[-0.42,-1.372],[-0.392,-1.395],[-0.363,-1.4],[-0.137,-1.4],[-0.102,-1.391],[-0.078,-1.367],[-0.065,-1.33],[-0.07,-1.305],[-0.08,-1.293],[-0.072,-1.277],[-0.074,-1.253],[-0.037,-1.216],[-0.009,-1.206],[0,-1.185],[0,-0.293],[-0.007,-0.268],[-0.07,-0.242],[-0.103,-0.209],[-0.103,-0.199],[-0.116,-0.182],[-0.16,-0.177],[-0.176,-0.161],[-0.316,-0.16],[-0.337,-0.177],[-0.379,-0.18],[-0.412,-0.147],[-0.413,-0.041],[-0.444,-0.005],[-0.456,0],[-0.847,0],[-0.864,-0.007],[-0.889,-0.032],[-0.898,-0.051],[-0.897,-0.234],[-0.89,-0.252],[-0.866,-0.278],[-0.868,-0.316],[-0.901,-0.349],[-0.912,-0.343],[-0.919,-0.348],[-0.973,-0.348],[-0.981,-0.343],[-1.041,-0.352],[-1.403,-0.425],[-1.439,-0.421],[-1.457,-0.434],[-1.484,-0.441],[-1.616,-0.464],[-1.919,-0.449],[-1.954,-0.449],[-1.989,-0.459],[-2.019,-0.478],[-2.087,-0.549],[-2.079,-0.559],[-2.091,-0.586]],"front":[[-1.397,0.057],[-1.366,0.021],[-1.344,0.01],[-1.303,0.011],[-1.28,0.028],[-1.27,0.023],[-1.211,0.023],[-1.193,0.004],[-1.182,0.002],[-1.169,0.015],[-1.105,0.014],[-1.08,0.029],[-1.082,0.042],[-1.125,0.084],[-1.116,0.093],[-0.411,0.092],[-0.39,0.119],[-0.368,0.098],[-0.349,0.123],[-0.321,0.087],[-0.371,0.033],[-0.37,0.008],[-0.363,0],[-0.29,0.002],[-0.239,0.046],[-0.194,0.047],[-0.178,0.062],[-0.177,0.107],[-0.159,0.124],[-0.159,0.15],[-0.15,0.159],[-0.046,0.161],[-0.011,0.183],[0,0.206],[-0.003,0.604],[-0.034,0.631],[-0.052,0.636],[-0.217,0.635],[-0.236,0.642],[-0.275,0.61],[-0.347,0.612],[-0.36,0.607],[-0.392,0.565],[-0.416,0.561],[-0.438,0.541],[-0.584,0.544],[-0.607,0.579],[-0.619,0.582],[-0.724,0.582],[-0.738,0.567],[-0.749,0.582],[-0.862,0.582],[-0.892,0.544],[-0.906,0.541],[-1.036,0.541],[-1.057,0.561],[-1.066,0.562],[-1.189,0.561],[-1.212,0.548],[-1.29,0.548],[-1.309,0.528],[-1.309,0.387],[-1.334,0.384],[-1.366,0.366],[-1.389,0.332],[-1.392,0.235],[-1.379,0.212],[-1.376,0.185],[-1.392,0.151],[-1.392,0.075]]},"features":{"side":{"knob":[[[-0.409,0.642],[-0.409,0.153],[-0.899,0.153],[-0.899,0.642]]],"knob_root":[[[-0.428,0.624],[-0.428,0.17],[-0.881,0.17],[-0.881,0.624]]],"knob_face":[[[-0.459,0.594],[-0.459,0.202],[-0.85,0.202],[-0.85,0.594]]],"knob_hub":[[[-0.588,0.465],[-0.588,0.332],[-0.721,0.332],[-0.721,0.465]]],"boss":[[[-0.07,0.349],[-0.07,0.013],[-0.405,0.013],[-0.405,0.349]]],"boss_bore":[[[-0.103,0.317],[-0.103,0.046],[-0.372,0.046],[-0.372,0.317]]],"screw_end":[[[-0.158,0.26],[-0.158,0.103],[-0.317,0.103],[-0.317,0.26]]],"base":[[[0.001,0.544],[0.001,-0.001],[-0.819,-0.001],[-0.819,0.544]]],"arm_pin":[[[-1.56,0.502],[-1.56,0.42],[-1.643,0.42],[-1.643,0.502]]]},"plan":{"arm":[[[-0.83,-1.104],[-0.841,-1.124],[-0.862,-1.134],[-0.979,-1.135],[-1.037,-1.131],[-1.179,-1.101],[-1.237,-1.089],[-1.527,-1.035],[-1.565,-1.024],[-1.605,-1.019],[-1.701,-1.019],[-1.92,-1.032],[-1.955,-1.032],[-1.981,-1.027],[-2.011,-1.013],[-2.039,-0.987],[-2.086,-0.914],[-2.101,-0.84],[-2.101,-0.641],[-2.086,-0.566],[-2.039,-0.494],[-2.011,-0.468],[-1.981,-0.454],[-1.955,-0.448],[-1.92,-0.448],[-1.701,-0.461],[-1.605,-0.461],[-1.565,-0.457],[-1.527,-0.446],[-1.237,-0.391],[-1.179,-0.379],[-1.037,-0.35],[-0.979,-0.345],[-0.862,-0.346],[-0.841,-0.356],[-0.83,-0.377]]],"knuckle":[[[-0.509,-0.923],[-0.509,-0.555],[-0.805,-0.555],[-0.805,-0.923]]],"index_rib":[[[-0.769,-0.897],[-0.769,-0.583],[-0.853,-0.583],[-0.853,-0.897]]],"shaft":[[[-0.571,-1.057],[-0.571,-0.422],[-0.746,-0.422],[-0.746,-1.057]]],"ear_right":[[[-0.444,-0.422],[-0.444,-0.271],[-0.871,-0.271],[-0.871,-0.422]]],"ear_left":[[[-0.495,-1.214],[-0.495,-1.057],[-0.819,-1.057],[-0.819,-1.214]]],"cap":[[[-0.512,-1.314],[-0.512,-1.214],[-0.8,-1.214],[-0.8,-1.314]]],"knob":[[[-0.412,-0.261],[-0.412,0.001],[-0.899,0.001],[-0.899,-0.261]]],"bolt_head":[[[-0.055,-1.398],[-0.055,-1.297],[-0.439,-1.297],[-0.439,-1.398]]],"clamp_bar":[[[-0.001,-1.297],[-0.001,-1.175],[-0.445,-1.175],[-0.445,-1.297]]],"body":[[[-0.001,-1.175],[-0.001,-0.176],[-0.822,-0.176],[-0.822,-1.175]]],"boss":[[[-0.125,-0.176],[-0.125,-0.158],[-0.37,-0.158],[-0.37,-0.176]]],"slot":[[[-0.495,-1.057],[-0.495,-0.422],[-0.827,-0.422],[-0.827,-1.057]]],"top_pocket":[[[-0.194,-0.983],[-0.194,-0.497],[-0.417,-0.497],[-0.417,-0.983]]],"ticks":[[[-0.41,-0.871],[-0.41,-0.858],[-0.483,-0.858],[-0.483,-0.871]],[[-0.41,-0.746],[-0.41,-0.734],[-0.483,-0.734],[-0.483,-0.746]],[[-0.41,-0.621],[-0.41,-0.609],[-0.483,-0.609],[-0.483,-0.621]],[[-0.442,-0.808],[-0.442,-0.795],[-0.481,-0.795],[-0.481,-0.808]],[[-0.442,-0.686],[-0.442,-0.672],[-0.481,-0.672],[-0.481,-0.686]]],"logo_panel":[[[-0.965,-0.964],[-0.923,-0.925],[-0.923,-0.555],[-0.965,-0.517],[-1.337,-0.588],[-1.375,-0.619],[-1.375,-0.862],[-1.337,-0.892]]],"window":[[[-1.441,-0.856],[-1.441,-0.624],[-1.687,-0.624],[-1.687,-0.608],[-2.064,-0.608],[-2.064,-0.873],[-1.687,-0.873],[-1.687,-0.856]]],"aperture":[[[-1.849,-0.775],[-1.849,-0.704],[-1.92,-0.704],[-1.92,-0.775]]],"aperture_sink":[[[-1.807,-0.818],[-1.807,-0.663],[-1.963,-0.663],[-1.963,-0.818]]]},"bottom":{"aperture":[[[-1.92,-0.777],[-1.92,-0.706],[-1.848,-0.706],[-1.848,-0.777]]],"aperture_bore":[[[-1.976,-0.834],[-1.976,-0.65],[-1.792,-0.65],[-1.792,-0.834]]],"pad":[[[-2.061,-0.955],[-2.061,-0.527],[-1.687,-0.527],[-1.687,-0.955]]],"rib_pockets":[[[-1.599,-0.905],[-1.599,-0.578],[-1.302,-0.683],[-1.28,-0.706],[-1.28,-0.777],[-1.302,-0.8]],[[-1.181,-0.777],[-1.181,-0.706],[-1.132,-0.686],[-0.88,-0.632],[-0.828,-0.658],[-0.813,-0.672],[-0.813,-0.811],[-0.828,-0.825],[-0.88,-0.851],[-1.132,-0.797]],[[-1.462,-0.95],[-1.462,-0.931],[-1.251,-0.866],[-1.233,-0.866],[-0.923,-0.92],[-0.923,-1.053],[-0.941,-1.065]],[[-1.462,-0.533],[-1.462,-0.552],[-1.251,-0.617],[-1.233,-0.617],[-0.923,-0.563],[-0.923,-0.43],[-0.941,-0.418]]],"screw":[[[-0.351,-1.085],[-0.351,-0.392],[-0.15,-0.392],[-0.15,-1.085]]],"knuckle":[[[-0.754,-0.931],[-0.754,-0.563],[-0.497,-0.563],[-0.497,-0.931]]]},"front":{"rail":[[[-0.299,0.213],[-1.164,0.213],[-1.164,0.092],[-0.299,0.092]]],"body":[[[-0.421,0.544],[-1.057,0.544],[-1.202,0.386],[-1.202,0.213],[-0.398,0.213],[-0.299,0.125],[-0.366,0.045],[-0.368,0.01],[-0.36,0.003],[-0.279,0.003],[-0.253,0.044],[-0.197,0.047],[-0.178,0.066],[-0.176,0.318],[-0.188,0.336],[-0.221,0.342],[-0.27,0.392]]],"clamp_bar":[[[-1.202,0.38],[-1.284,0.38],[-1.292,0.371],[-1.292,0.032],[-1.284,0.023],[-1.195,0.023],[-1.182,0.015],[-1.097,0.015],[-1.08,0.032],[-1.164,0.125],[-1.164,0.195],[-1.13,0.229],[-1.202,0.229]]],"knob":[[[0.001,0.638],[-0.26,0.638],[-0.26,0.161],[0.001,0.161]]],"bolt_head":[[[-1.292,0.391],[-1.398,0.391],[-1.398,0.006],[-1.292,0.006]]],"head_slot":[[[-1.323,0.234],[-1.398,0.234],[-1.398,0.152],[-1.323,0.152]]],"ear_right":[[[-0.27,0.612],[-0.365,0.612],[-0.365,0.187],[-0.27,0.187]]],"ear_left":[[[-1.056,0.562],[-1.208,0.562],[-1.208,0.237],[-1.056,0.237]]],"cap":[[[-1.208,0.549],[-1.309,0.549],[-1.309,0.25],[-1.208,0.25]]],"index_rib":[[[-0.595,0.583],[-0.886,0.583],[-0.886,0.544],[-0.595,0.544]]],"screw_end":[[[-0.158,0.267],[-0.176,0.267],[-0.176,0.121],[-0.158,0.121]]]}},"placement":{"side":{"plane":"xy","offset":{"x":"front_x","y":"clamp_bottom_y"}},"plan":{"plane":"xz","offset":{"x":"front_x","y":"knob_face_z"}},"bottom":{"plane":"xz","offset":{"x":"front_x","y":"knob_face_z"}},"front":{"plane":"zy","offset":{"x":"knob_face_z","y":"clamp_bottom_y"}}},"bounds":{"min":[-0.4897,-0.208,-0.658],"max":[0.409,1.6324,0.75]},"volume_in3":0.6521,"centroid":[-0.1204,0.399,0.0607],"shell":[-0.1163,0.3338,0.06],"area_in2":12.1887,"triangles":8252,"manifold":true,"rail_seat":{"x":[-0.41,0.409],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-0.488,-0.208,-0.658,0.409,0.16,0.75],[-0.49,0.16,-0.651,0.339,0.528,0.75],[-0.419,0.528,-0.394,-0.092,0.896,0.394],[-0.419,0.896,-0.325,-0.091,1.632,0.325]],"slots":["body"]},"magpul-mlok-aluminum-rail-section-3-slot":{"part":"magpul-mlok-aluminum-rail-section-3-slot","model":"magpul-mlok-aluminum-rail-section-3-slot.glb","script":"magpul_mlok_aluminum_rail_section_3_slot.py","inputs":{"magpul-mlok-aluminum-rail-section-3-slot.counterbore_d":0.37,"magpul-mlok-aluminum-rail-section-3-slot.end_bevel_run":0.14,"magpul-mlok-aluminum-rail-section-3-slot.height":0.24,"magpul-mlok-aluminum-rail-section-3-slot.length":1.576,"magpul-mlok-aluminum-rail-section-3-slot.neck_width":0.603,"magpul-mlok-aluminum-rail-section-3-slot.rail_slot0_x":0.395,"magpul-mlok-aluminum-rail-section-3-slot.rail_slots":3,"magpul-mlok-aluminum-rail-section-3-slot.screw_count":2,"magpul-mlok-aluminum-rail-section-3-slot.screw_head_d":0.2,"magpul-mlok-aluminum-rail-section-3-slot.screw_head_height":0.08,"magpul-mlok-aluminum-rail-section-3-slot.screw_seat_below_top":0.2,"magpul-mlok-aluminum-rail-section-3-slot.screw_step":2,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{"plan":[[-0.002,0.032],[-0.002,-0.05],[0.008,-0.134],[0.02,-0.197],[0.042,-0.274],[0.058,-0.299],[0.084,-0.314],[0.174,-0.39],[0.265,-0.391],[0.294,-0.373],[0.466,-0.372],[0.478,-0.376],[0.489,-0.389],[0.502,-0.392],[0.659,-0.393],[0.693,-0.373],[0.859,-0.373],[0.877,-0.376],[0.896,-0.393],[0.971,-0.393],[1.063,-0.392],[1.082,-0.377],[1.095,-0.374],[1.268,-0.374],[1.295,-0.393],[1.379,-0.393],[1.395,-0.387],[1.49,-0.312],[1.516,-0.304],[1.526,-0.294],[1.549,-0.217],[1.565,-0.14],[1.577,0.006],[1.575,0.075],[1.565,0.157],[1.55,0.226],[1.528,0.296],[1.455,0.377],[1.383,0.444],[1.298,0.445],[1.275,0.422],[1.247,0.419],[1.092,0.421],[1.083,0.425],[1.072,0.442],[1.052,0.445],[0.897,0.444],[0.883,0.425],[0.873,0.421],[0.712,0.42],[0.691,0.422],[0.675,0.443],[0.666,0.445],[0.527,0.446],[0.497,0.442],[0.49,0.429],[0.48,0.422],[0.442,0.419],[0.299,0.421],[0.291,0.423],[0.279,0.442],[0.272,0.445],[0.193,0.445],[0.177,0.44],[0.05,0.299],[0.014,0.171]]},"features":{"plan":{}},"placement":{"plan":{"plane":"xz","offset":{}}},"bounds":{"min":[0,0,-0.4175],"max":[1.576,0.24,0.4175]},"volume_in3":0.1581,"centroid":[0.7875,0.0982,0],"shell":[0.7882,0.0976,0],"area_in2":3.8084,"triangles":3092,"manifold":true,"slabs":[[0,0,-0.417,1.576,0.24,0.417]],"slots":["body","screws"]},"magpul-mlok-aluminum-rail-section-5-slot":{"part":"magpul-mlok-aluminum-rail-section-5-slot","model":"magpul-mlok-aluminum-rail-section-5-slot.glb","script":"magpul_mlok_aluminum_rail_section_5_slot.py","inputs":{"magpul-mlok-aluminum-rail-section-5-slot.counterbore_d":0.37,"magpul-mlok-aluminum-rail-section-5-slot.end_bevel_run":0.122,"magpul-mlok-aluminum-rail-section-5-slot.height":0.24,"magpul-mlok-aluminum-rail-section-5-slot.length":2.382,"magpul-mlok-aluminum-rail-section-5-slot.neck_width":0.602,"magpul-mlok-aluminum-rail-section-5-slot.rail_slot0_x":0.403,"magpul-mlok-aluminum-rail-section-5-slot.rail_slots":5,"magpul-mlok-aluminum-rail-section-5-slot.screw_count":2,"magpul-mlok-aluminum-rail-section-5-slot.screw_head_d":0.21,"magpul-mlok-aluminum-rail-section-5-slot.screw_head_height":0.08,"magpul-mlok-aluminum-rail-section-5-slot.screw_seat_below_top":0.2,"magpul-mlok-aluminum-rail-section-5-slot.screw_step":4,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{"plan":[[0.022,0.061],[0.022,-0.041],[0.036,-0.158],[0.072,-0.28],[0.171,-0.383],[0.197,-0.403],[0.221,-0.411],[0.297,-0.411],[0.302,-0.397],[0.314,-0.389],[0.495,-0.389],[0.506,-0.395],[0.509,-0.408],[0.516,-0.413],[0.688,-0.413],[0.693,-0.399],[0.707,-0.389],[0.885,-0.389],[0.899,-0.397],[0.905,-0.413],[1.078,-0.413],[1.084,-0.408],[1.084,-0.399],[1.1,-0.389],[1.274,-0.389],[1.292,-0.401],[1.297,-0.413],[1.473,-0.413],[1.475,-0.399],[1.488,-0.39],[1.575,-0.389],[1.671,-0.39],[1.688,-0.413],[1.864,-0.413],[1.869,-0.397],[1.879,-0.39],[2.062,-0.39],[2.081,-0.413],[2.168,-0.413],[2.194,-0.394],[2.234,-0.354],[2.303,-0.276],[2.319,-0.226],[2.34,-0.137],[2.351,-0.048],[2.353,0.035],[2.342,0.154],[2.327,0.224],[2.304,0.297],[2.205,0.39],[2.174,0.409],[2.083,0.409],[2.064,0.39],[1.884,0.39],[1.871,0.401],[1.871,0.408],[1.866,0.411],[1.692,0.411],[1.682,0.396],[1.669,0.39],[1.495,0.39],[1.482,0.396],[1.475,0.411],[1.298,0.411],[1.284,0.392],[1.098,0.392],[1.09,0.397],[1.083,0.411],[0.957,0.413],[0.905,0.411],[0.901,0.401],[0.889,0.392],[0.709,0.392],[0.697,0.399],[0.688,0.413],[0.514,0.413],[0.503,0.396],[0.492,0.392],[0.353,0.392],[0.312,0.394],[0.295,0.413],[0.204,0.413],[0.173,0.392],[0.07,0.299],[0.044,0.211],[0.029,0.134]]},"features":{"plan":{}},"placement":{"plan":{"plane":"xz","offset":{}}},"bounds":{"min":[0,0,-0.4175],"max":[2.382,0.24,0.4175]},"volume_in3":0.2658,"centroid":[1.191,0.1009,0],"shell":[1.191,0.1032,0],"area_in2":5.6837,"triangles":3284,"manifold":true,"slabs":[[0,0,-0.417,2.382,0.24,0.417]],"slots":["body","screws"]},"magpul-mlok-aluminum-rail-section-7-slot":{"part":"magpul-mlok-aluminum-rail-section-7-slot","model":"magpul-mlok-aluminum-rail-section-7-slot.glb","script":"magpul_mlok_aluminum_rail_section_7_slot.py","inputs":{"magpul-mlok-aluminum-rail-section-7-slot.counterbore_d":0.369,"magpul-mlok-aluminum-rail-section-7-slot.end_bevel_run":0.131,"magpul-mlok-aluminum-rail-section-7-slot.height":0.24,"magpul-mlok-aluminum-rail-section-7-slot.length":3.162,"magpul-mlok-aluminum-rail-section-7-slot.neck_width":0.602,"magpul-mlok-aluminum-rail-section-7-slot.rail_slot0_x":0.398,"magpul-mlok-aluminum-rail-section-7-slot.rail_slots":7,"magpul-mlok-aluminum-rail-section-7-slot.screw_count":2,"magpul-mlok-aluminum-rail-section-7-slot.screw_head_d":0.205,"magpul-mlok-aluminum-rail-section-7-slot.screw_head_height":0.08,"magpul-mlok-aluminum-rail-section-7-slot.screw_seat_below_top":0.2,"magpul-mlok-aluminum-rail-section-7-slot.screw_step":6,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{"plan":[[-0.001,-0.033],[0.011,-0.154],[0.03,-0.236],[0.05,-0.294],[0.093,-0.349],[0.167,-0.428],[0.18,-0.438],[0.201,-0.445],[0.275,-0.443],[0.297,-0.417],[0.482,-0.418],[0.492,-0.423],[0.499,-0.442],[0.597,-0.444],[0.674,-0.442],[0.684,-0.424],[0.696,-0.416],[0.8,-0.414],[0.88,-0.417],[0.901,-0.443],[1.061,-0.443],[1.074,-0.441],[1.082,-0.425],[1.093,-0.415],[1.277,-0.416],[1.289,-0.426],[1.296,-0.442],[1.467,-0.442],[1.475,-0.439],[1.479,-0.424],[1.487,-0.416],[1.499,-0.414],[1.672,-0.415],[1.686,-0.425],[1.692,-0.441],[1.705,-0.443],[1.869,-0.441],[1.878,-0.421],[1.888,-0.415],[2.072,-0.416],[2.086,-0.428],[2.086,-0.437],[2.093,-0.442],[2.262,-0.443],[2.272,-0.437],[2.274,-0.424],[2.283,-0.417],[2.32,-0.415],[2.469,-0.417],[2.493,-0.443],[2.659,-0.444],[2.671,-0.436],[2.671,-0.425],[2.677,-0.42],[2.709,-0.416],[2.869,-0.418],[2.888,-0.442],[2.974,-0.443],[3.038,-0.383],[3.112,-0.295],[3.132,-0.232],[3.151,-0.144],[3.163,-0.04],[3.163,0.037],[3.148,0.165],[3.118,0.275],[3.1,0.3],[3.091,0.302],[3.046,0.348],[2.988,0.393],[2.897,0.394],[2.875,0.374],[2.83,0.372],[2.685,0.375],[2.675,0.39],[2.666,0.394],[2.508,0.395],[2.493,0.393],[2.486,0.381],[2.474,0.373],[2.292,0.374],[2.282,0.378],[2.271,0.393],[2.217,0.393],[2.096,0.394],[2.074,0.374],[1.888,0.375],[1.867,0.394],[1.705,0.395],[1.694,0.393],[1.677,0.373],[1.491,0.374],[1.481,0.379],[1.474,0.393],[1.297,0.394],[1.279,0.375],[1.096,0.373],[1.085,0.377],[1.074,0.393],[1.035,0.395],[0.897,0.393],[0.886,0.378],[0.878,0.374],[0.748,0.372],[0.694,0.374],[0.681,0.381],[0.673,0.394],[0.504,0.394],[0.496,0.392],[0.486,0.378],[0.476,0.373],[0.295,0.373],[0.284,0.378],[0.269,0.393],[0.18,0.393],[0.117,0.346],[0.072,0.303],[0.059,0.298],[0.047,0.282],[0.027,0.222],[0.008,0.127],[-0.001,0.028]]},"features":{"plan":{}},"placement":{"plan":{"plane":"xz","offset":{}}},"bounds":{"min":[0,0,-0.4175],"max":[3.162,0.24,0.4175]},"volume_in3":0.3643,"centroid":[1.5814,0.1011,0],"shell":[1.5808,0.1053,0],"area_in2":7.4475,"triangles":3476,"manifold":true,"slabs":[[0,0,-0.417,3.162,0.24,0.417]],"slots":["body","screws"]},"magpul-mlok-aluminum-rail-section-9-slot":{"part":"magpul-mlok-aluminum-rail-section-9-slot","model":"magpul-mlok-aluminum-rail-section-9-slot.glb","script":"magpul_mlok_aluminum_rail_section_9_slot.py","inputs":{"magpul-mlok-aluminum-rail-section-9-slot.counterbore_d":0.37,"magpul-mlok-aluminum-rail-section-9-slot.end_bevel_run":0.131,"magpul-mlok-aluminum-rail-section-9-slot.height":0.24,"magpul-mlok-aluminum-rail-section-9-slot.length":3.943,"magpul-mlok-aluminum-rail-section-9-slot.neck_width":0.6,"magpul-mlok-aluminum-rail-section-9-slot.rail_slot0_x":0.395,"magpul-mlok-aluminum-rail-section-9-slot.rail_slots":9,"magpul-mlok-aluminum-rail-section-9-slot.screw_count":3,"magpul-mlok-aluminum-rail-section-9-slot.screw_head_d":0.205,"magpul-mlok-aluminum-rail-section-9-slot.screw_head_height":0.08,"magpul-mlok-aluminum-rail-section-9-slot.screw_seat_below_top":0.2,"magpul-mlok-aluminum-rail-section-9-slot.screw_step":4,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{"plan":[[-0.005,0.024],[-0.003,-0.071],[0.003,-0.126],[0.018,-0.201],[0.04,-0.278],[0.144,-0.384],[0.171,-0.402],[0.256,-0.402],[0.278,-0.382],[0.464,-0.382],[0.479,-0.402],[0.499,-0.402],[0.655,-0.402],[0.677,-0.382],[0.859,-0.382],[0.874,-0.402],[0.884,-0.404],[1.048,-0.404],[1.068,-0.384],[1.076,-0.382],[1.248,-0.382],[1.259,-0.384],[1.268,-0.399],[1.277,-0.404],[1.447,-0.404],[1.467,-0.384],[1.488,-0.382],[1.656,-0.384],[1.67,-0.404],[1.848,-0.404],[1.866,-0.384],[2.053,-0.384],[2.071,-0.404],[2.099,-0.406],[2.233,-0.406],[2.247,-0.404],[2.268,-0.384],[2.45,-0.383],[2.461,-0.391],[2.468,-0.404],[2.484,-0.406],[2.636,-0.406],[2.648,-0.404],[2.658,-0.388],[2.669,-0.383],[2.847,-0.383],[2.857,-0.387],[2.871,-0.406],[3.041,-0.406],[3.062,-0.385],[3.072,-0.383],[3.244,-0.383],[3.258,-0.389],[3.263,-0.4],[3.272,-0.405],[3.441,-0.405],[3.449,-0.403],[3.463,-0.385],[3.584,-0.383],[3.651,-0.385],[3.674,-0.405],[3.767,-0.403],[3.897,-0.285],[3.932,-0.157],[3.946,-0.021],[3.944,0.074],[3.936,0.139],[3.917,0.226],[3.895,0.297],[3.764,0.433],[3.746,0.437],[3.673,0.437],[3.647,0.413],[3.463,0.413],[3.444,0.435],[3.436,0.437],[3.345,0.437],[3.274,0.437],[3.248,0.413],[3.169,0.413],[3.065,0.413],[3.054,0.42],[3.047,0.435],[3.039,0.437],[2.875,0.437],[2.864,0.43],[2.855,0.415],[2.794,0.413],[2.668,0.413],[2.642,0.437],[2.478,0.437],[2.47,0.435],[2.463,0.422],[2.45,0.413],[2.399,0.411],[2.269,0.413],[2.258,0.42],[2.249,0.435],[2.241,0.437],[2.081,0.437],[2.068,0.43],[2.059,0.415],[2.038,0.413],[1.872,0.413],[1.857,0.424],[1.852,0.435],[1.844,0.437],[1.724,0.437],[1.674,0.435],[1.667,0.42],[1.655,0.412],[1.475,0.412],[1.462,0.422],[1.455,0.435],[1.443,0.437],[1.287,0.437],[1.277,0.435],[1.269,0.419],[1.258,0.412],[1.167,0.412],[1.078,0.412],[1.067,0.419],[1.058,0.435],[1.048,0.437],[0.894,0.437],[0.881,0.435],[0.863,0.412],[0.805,0.41],[0.681,0.412],[0.67,0.421],[0.665,0.432],[0.649,0.436],[0.486,0.434],[0.47,0.412],[0.436,0.41],[0.286,0.412],[0.262,0.434],[0.176,0.434],[0.094,0.352],[0.046,0.291],[0.009,0.156]]},"features":{"plan":{}},"placement":{"plan":{"plane":"xz","offset":{}}},"bounds":{"min":[0,0,-0.4175],"max":[3.943,0.24,0.4175]},"volume_in3":0.4509,"centroid":[1.9717,0.1009,0],"shell":[1.9714,0.1048,0],"area_in2":9.4433,"triangles":4708,"manifold":true,"slabs":[[0,0,-0.417,3.943,0.24,0.417]],"slots":["body","screws"]},"magpul-mlok-hand-stop-moe-adapter":{"part":"magpul-mlok-hand-stop-moe-adapter","model":"magpul-mlok-hand-stop-moe-adapter.glb","script":"magpul_mlok_hand_stop_moe_adapter.py","inputs":{"magpul-mlok-hand-stop-moe-adapter.cover_corner_radius":0.11,"magpul-mlok-hand-stop-moe-adapter.cover_edge_height":0.12,"magpul-mlok-hand-stop-moe-adapter.cover_end_lean":0.052,"magpul-mlok-hand-stop-moe-adapter.cover_height":0.24,"magpul-mlok-hand-stop-moe-adapter.cover_shoulder_height":0.203,"magpul-mlok-hand-stop-moe-adapter.edge_height":0.021,"magpul-mlok-hand-stop-moe-adapter.end_inset":0.023,"magpul-mlok-hand-stop-moe-adapter.end_notch_depth":0.03,"magpul-mlok-hand-stop-moe-adapter.end_notch_width":0.3,"magpul-mlok-hand-stop-moe-adapter.end_width":0.9,"magpul-mlok-hand-stop-moe-adapter.height":0.103,"magpul-mlok-hand-stop-moe-adapter.land_width":0.656,"magpul-mlok-hand-stop-moe-adapter.length":4.715,"magpul-mlok-hand-stop-moe-adapter.position_pitch":3.149,"magpul-mlok-hand-stop-moe-adapter.position_x":0.783,"magpul-mlok-hand-stop-moe-adapter.positions":2,"magpul-mlok-hand-stop-moe-adapter.recess_depth":0.066,"magpul-mlok-hand-stop-moe-adapter.recess_length":1.232,"magpul-mlok-hand-stop-moe-adapter.recess_width":0.279,"magpul-mlok-hand-stop-moe-adapter.score_width":0.02,"magpul-mlok-hand-stop-moe-adapter.score_x":1.552,"magpul-mlok-hand-stop-moe-adapter.screw_hole_diameter":0.224,"magpul-mlok-hand-stop-moe-adapter.width":1.036,"std.mlok.interval":0.7874015748031495,"std.mlok.slot_corner_r":0.0937007874015748},"profiles":{},"features":{},"placement":{},"bounds":{"min":[0,0,-0.518],"max":[4.715,0.24,0.518]},"volume_in3":0.5198,"centroid":[2.3575,0.081,0],"shell":[2.3575,0.0622,0],"area_in2":10.1192,"triangles":5032,"manifold":true,"slabs":[[0,0,-0.453,1.572,0.128,0.453],[1.572,0,-0.518,3.143,0.24,0.518],[3.143,0,-0.453,4.715,0.128,0.453]],"slots":["body"]},"magpul-mlok-hand-stop":{"part":"magpul-mlok-hand-stop","model":"magpul-mlok-hand-stop.glb","script":"magpul_mlok_hand_stop.py","inputs":{"magpul-mlok-hand-stop.lug_x":0.374,"magpul-mlok-hand-stop.screw_head_diameter":0.375,"magpul-mlok-hand-stop.screw_head_proud":0.033,"magpul-mlok-hand-stop.screw_recess_diameter":0.399,"magpul-mlok-hand-stop.screw_recess_floor_diameter":0.358,"std.mlok.interval":0.7874015748031495},"profiles":{"side":[[0,0.275],[0.003,0.048],[0.06,0.011],[0.097,0],[1.458,0],[1.557,0.035],[1.569,0.045],[1.575,0.078],[1.569,0.247],[1.391,0.25],[1.37,0.239],[1.154,0.232],[1.031,0.249],[0.886,0.325],[0.823,0.389],[0.769,0.478],[0.753,0.475],[0.73,0.498],[0.745,0.526],[0.725,0.575],[0.712,0.572],[0.688,0.595],[0.707,0.625],[0.692,0.673],[0.659,0.696],[0.678,0.728],[0.668,0.778],[0.639,0.801],[0.661,0.83],[0.656,0.884],[0.628,0.91],[0.655,0.937],[0.655,0.99],[0.63,1.017],[0.659,1.042],[0.666,1.096],[0.644,1.122],[0.674,1.145],[0.686,1.197],[0.668,1.228],[0.689,1.249],[0.702,1.248],[0.729,1.311],[0.79,1.401],[0.775,1.49],[0.746,1.505],[0.48,1.468],[0.387,1.427],[0.346,1.385],[0.265,1.273],[0.062,0.954],[0.022,0.879],[0.004,0.8]],"front":[[-0.527,0.022],[-0.523,0.005],[-0.508,0.002],[-0.348,0.116],[0.35,0.116],[0.52,0],[0.527,0.045],[0.284,1.426],[0.263,1.453],[0.232,1.465],[0.107,1.498],[-0.005,1.504],[-0.141,1.49],[-0.262,1.456],[-0.284,1.429]],"plan":[[0,-0.396],[0.012,-0.47],[0.061,-0.519],[0.069,-0.512],[0.107,-0.526],[1.459,-0.526],[1.548,-0.488],[1.576,-0.449],[1.576,0.452],[1.56,0.477],[1.489,0.518],[1.455,0.526],[0.11,0.526],[0.077,0.517],[0.034,0.487],[0.009,0.463],[0.003,0.445]]},"features":{"side":{},"front":{},"plan":{}},"placement":{"side":{"plane":"xy","offset":{}},"front":{"plane":"zy","offset":{}},"plan":{"plane":"xz","offset":{}}},"bounds":{"min":[0,0,-0.526],"max":[1.575,1.504,0.526]},"volume_in3":0.843,"centroid":[0.5093,0.5654,0.0007],"shell":[0.6528,0.4961,0.0007],"area_in2":7.5385,"triangles":3302,"manifold":true,"slabs":[[0,0,-0.526,0.394,1.43,0.526],[0.394,0,-0.526,0.788,1.504,0.526],[0.788,0,-0.526,1.181,1.416,0.526],[1.181,0,-0.526,1.575,0.265,0.526]],"slots":["body","screws"]},"magpul-mlok-index-panel":{"part":"magpul-mlok-index-panel","model":"magpul-mlok-index-panel.glb","script":"magpul_mlok_index_panel.py","inputs":{"magpul-mlok-index-panel.lug_x":0.387,"magpul-mlok-index-panel.screw_head_diameter":0.364,"magpul-mlok-index-panel.screw_head_proud":0.034,"magpul-mlok-index-panel.screw_hole_diameter":0.219,"magpul-mlok-index-panel.screw_recess_diameter":0.429,"magpul-mlok-index-panel.screw_recess_floor_diameter":0.36},"profiles":{"side":[[0,0.086],[0.004,0.057],[0.021,0.035],[0.118,0],[1.441,0],[1.467,0.003],[1.55,0.046],[1.558,0.06],[1.558,0.146],[1.552,0.234],[1.543,0.245],[1.38,0.246],[1.34,0.263],[1.303,0.3],[1.284,0.36],[1.217,0.739],[1.208,0.745],[1.05,0.745],[1.036,0.726],[0.967,0.329],[0.947,0.291],[0.907,0.257],[0.866,0.245],[0.603,0.246],[0.565,0.236],[0.415,0.227],[0.226,0.234],[0.171,0.246],[0.016,0.245],[0.004,0.231]],"front":[[-0.519,0.025],[-0.515,0.006],[-0.503,0],[-0.345,0.11],[0.339,0.112],[0.507,0],[0.518,0.008],[0.519,0.026],[0.504,0.124],[0.339,0.583],[0.321,0.614],[0.263,0.665],[0.166,0.714],[0.092,0.735],[-0.006,0.745],[-0.092,0.735],[-0.173,0.712],[-0.256,0.671],[-0.315,0.624],[-0.367,0.512],[-0.503,0.128]],"plan":[[0,0.436],[0,0],[0,-0.437],[0.003,-0.453],[0.023,-0.473],[0.082,-0.509],[0.115,-0.519],[1.442,-0.519],[1.482,-0.504],[1.486,-0.507],[1.539,-0.469],[1.558,-0.436],[1.559,0.429],[1.554,0.451],[1.54,0.469],[1.483,0.505],[1.449,0.518],[0.123,0.519],[0.08,0.508],[0.022,0.471],[0.007,0.455]]},"features":{"side":{},"front":{"plate":[[[0.558,-0.036],[-0.558,-0.036],[-0.558,0.038],[-0.513,0.055],[-0.477,0.089],[-0.44,0.124],[-0.403,0.159],[-0.366,0.19],[-0.329,0.21],[-0.292,0.219],[-0.255,0.226],[-0.218,0.231],[-0.181,0.235],[-0.145,0.239],[-0.108,0.242],[-0.071,0.243],[-0.034,0.245],[0,0.245],[0.034,0.245],[0.071,0.243],[0.108,0.242],[0.145,0.239],[0.181,0.235],[0.218,0.231],[0.255,0.226],[0.292,0.219],[0.329,0.21],[0.366,0.19],[0.403,0.159],[0.44,0.124],[0.477,0.089],[0.513,0.055],[0.558,0.038]]]},"plan":{"fin_foot":[[[1.307,0.518],[1.312,0.502],[1.329,0.451],[1.345,0.401],[1.368,0.351],[1.385,0.301],[1.393,0.251],[1.396,0.2],[1.399,0.1],[1.404,0],[1.399,-0.1],[1.396,-0.2],[1.393,-0.251],[1.385,-0.301],[1.368,-0.351],[1.345,-0.401],[1.329,-0.451],[1.312,-0.502],[1.307,-0.518],[0.953,-0.518],[0.948,-0.502],[0.931,-0.451],[0.915,-0.401],[0.892,-0.351],[0.875,-0.301],[0.867,-0.251],[0.864,-0.2],[0.861,-0.1],[0.856,0],[0.861,0.1],[0.864,0.2],[0.867,0.251],[0.875,0.301],[0.892,0.351],[0.915,0.401],[0.931,0.451],[0.948,0.502],[0.953,0.518]]],"fin_root":[[[1.193,0.518],[1.197,0.502],[1.212,0.451],[1.228,0.401],[1.247,0.351],[1.264,0.301],[1.276,0.251],[1.281,0.2],[1.284,0.1],[1.289,0],[1.284,-0.1],[1.281,-0.2],[1.276,-0.251],[1.264,-0.301],[1.247,-0.351],[1.228,-0.401],[1.212,-0.451],[1.197,-0.502],[1.193,-0.518],[1.067,-0.518],[1.063,-0.502],[1.048,-0.451],[1.032,-0.401],[1.013,-0.351],[0.996,-0.301],[0.984,-0.251],[0.979,-0.2],[0.976,-0.1],[0.971,0],[0.976,0.1],[0.979,0.2],[0.984,0.251],[0.996,0.301],[1.013,0.351],[1.032,0.401],[1.048,0.451],[1.063,0.502],[1.067,0.518]]],"fin_tip":[[[1.178,0.518],[1.178,0.502],[1.178,0.451],[1.179,0.401],[1.182,0.351],[1.183,0.301],[1.192,0.251],[1.202,0.2],[1.217,0.1],[1.219,0],[1.217,-0.1],[1.202,-0.2],[1.192,-0.251],[1.183,-0.301],[1.182,-0.351],[1.179,-0.401],[1.178,-0.451],[1.178,-0.502],[1.178,-0.518],[1.081,-0.518],[1.081,-0.502],[1.081,-0.451],[1.081,-0.401],[1.078,-0.351],[1.077,-0.301],[1.068,-0.251],[1.058,-0.2],[1.043,-0.1],[1.041,0],[1.043,0.1],[1.058,0.2],[1.068,0.251],[1.077,0.301],[1.078,0.351],[1.081,0.401],[1.081,0.451],[1.081,0.502],[1.081,0.518]]]}},"placement":{"side":{"plane":"xy","offset":{}},"front":{"plane":"zy","offset":{}},"plan":{"plane":"xz","offset":{}}},"bounds":{"min":[0,0,-0.519],"max":[1.558,0.745,0.519]},"volume_in3":0.2792,"centroid":[0.9239,0.2484,-0.0006],"shell":[0.8155,0.2095,0],"area_in2":4.8584,"triangles":4948,"manifold":true,"slabs":[[0,0,-0.519,0.779,0.262,0.519],[0.779,0,-0.519,1.558,0.745,0.519]],"slots":["body","screws"]},"magpul-mlok-mvg":{"part":"magpul-mlok-mvg","model":"magpul-mlok-mvg.glb","script":"magpul_mlok_mvg.py","inputs":{"magpul-mlok-mvg.base_wall":0.115,"magpul-mlok-mvg.rib_groove_depth":0.028,"magpul-mlok-mvg.rib_groove_first_y":1.389,"magpul-mlok-mvg.rib_groove_length":0.7,"magpul-mlok-mvg.rib_groove_pitch":0.0856,"magpul-mlok-mvg.rib_groove_width":0.048,"magpul-mlok-mvg.rib_grooves":16,"magpul-mlok-mvg.width":1.17},"profiles":{"side":[[0,1.77],[0.029,1.736],[0.032,1.707],[0.009,1.692],[0.003,1.681],[0.026,1.662],[0.034,1.636],[0.034,1.628],[0.005,1.599],[0.008,1.588],[0.026,1.575],[0.032,1.554],[0.029,1.535],[0.005,1.517],[0.026,1.488],[0.034,1.453],[0.005,1.427],[0.005,1.419],[0.026,1.401],[0.034,1.382],[0.032,1.369],[0.003,1.345],[0.016,1.203],[0.026,1.184],[0.029,1.158],[0.05,1.121],[0.058,1.084],[0.069,1.073],[0.069,1.05],[0.092,0.983],[0.095,0.954],[0.106,0.939],[0.106,0.91],[0.121,0.851],[0.121,0.801],[0.135,0.772],[0.137,0.73],[0.137,0.461],[0.124,0.389],[0.087,0.286],[0.013,0.173],[0.003,0.144],[0.003,0.057],[0.016,0.028],[0.075,0],[0.413,0],[0.429,0.005],[0.445,0],[0.561,0],[0.58,0.005],[0.598,0],[0.894,0],[0.902,0.008],[0.936,0.003],[0.952,0.008],[1.02,0.005],[1.026,0.011],[1.036,0.011],[1.044,0.003],[1.065,0.013],[1.081,0.008],[1.176,0.011],[1.184,0.005],[1.226,0.005],[1.232,0],[1.414,0],[1.427,0.008],[1.469,0.013],[1.517,0.029],[1.547,0.054],[1.55,0.086],[1.55,0.133],[1.534,0.173],[1.494,0.228],[1.452,0.305],[1.418,0.397],[1.418,0.434],[1.405,0.466],[1.405,0.801],[1.418,0.817],[1.42,0.891],[1.484,1.113],[1.497,1.137],[1.526,1.226],[1.526,1.258],[1.537,1.3],[1.537,1.369],[1.53,1.378],[1.514,1.378],[1.508,1.385],[1.516,1.411],[1.539,1.443],[1.516,1.477],[1.542,1.527],[1.508,1.554],[1.518,1.585],[1.537,1.607],[1.537,1.622],[1.527,1.629],[1.519,1.626],[1.508,1.644],[1.516,1.665],[1.539,1.694],[1.539,1.707],[1.51,1.731],[1.513,1.747],[1.539,1.789],[1.53,1.801],[1.519,1.801],[1.508,1.81],[1.516,1.834],[1.539,1.863],[1.539,1.871],[1.516,1.9],[1.539,1.95],[1.539,1.966],[1.508,1.982],[1.518,2.011],[1.539,2.034],[1.534,2.05],[1.516,2.066],[1.518,2.084],[1.539,2.116],[1.537,2.137],[1.508,2.153],[1.513,2.172],[1.539,2.206],[1.539,2.216],[1.516,2.24],[1.523,2.264],[1.539,2.285],[1.539,2.298],[1.521,2.319],[1.518,2.333],[1.539,2.38],[1.539,2.391],[1.521,2.409],[1.518,2.42],[1.539,2.457],[1.539,2.475],[1.518,2.499],[1.523,2.517],[1.539,2.536],[1.542,2.554],[1.518,2.583],[1.521,2.602],[1.542,2.636],[1.518,2.671],[1.521,2.689],[1.539,2.71],[1.537,2.782],[1.526,2.805],[1.523,2.887],[1.51,2.948],[1.483,2.978],[1.467,2.981],[1.356,2.981],[1.308,2.97],[1.139,2.973],[1.071,2.968],[0.999,2.973],[0.97,2.968],[0.659,2.973],[0.635,2.968],[0.334,2.97],[0.276,2.965],[0.234,2.97],[0.078,2.97],[0.054,2.962],[0.029,2.924],[0.029,2.853],[0.016,2.824],[0.016,2.75],[0.003,2.718],[0.034,2.663],[0.005,2.639],[0.008,2.623],[0.037,2.583],[0.005,2.536],[0.026,2.517],[0.034,2.491],[0.016,2.467],[0.011,2.449],[0.037,2.412],[0.034,2.399],[0.013,2.378],[0.016,2.351],[0.029,2.338],[0.037,2.317],[0.008,2.288],[0.032,2.248],[0.034,2.23],[0.013,2.211],[0.005,2.195],[0.026,2.18],[0.034,2.145],[0.008,2.119],[0.008,2.103],[0.026,2.09],[0.034,2.069],[0.034,2.053],[0.008,2.026],[0.008,2.016],[0.029,1.995],[0.034,1.971],[0.005,1.945],[0.008,1.934],[0.026,1.918],[0.034,1.894],[0.034,1.886],[0.005,1.863],[0.005,1.852],[0.026,1.834],[0.034,1.797]],"plan":[[0,-0.003],[0.016,-0.141],[0.063,-0.263],[0.127,-0.354],[0.224,-0.438],[0.328,-0.49],[0.425,-0.513],[0.536,-0.553],[0.677,-0.58],[0.809,-0.583],[0.984,-0.56],[1.114,-0.514],[1.205,-0.495],[1.301,-0.451],[1.363,-0.407],[1.439,-0.33],[1.494,-0.244],[1.533,-0.127],[1.546,0.029],[1.526,0.153],[1.483,0.263],[1.413,0.361],[1.324,0.436],[1.209,0.493],[1.121,0.511],[0.976,0.562],[0.867,0.58],[0.731,0.583],[0.563,0.56],[0.43,0.514],[0.341,0.495],[0.269,0.464],[0.202,0.423],[0.107,0.33],[0.055,0.247],[0.013,0.127],[0.002,0]],"front":[[-0.585,1.21],[-0.564,1.054],[-0.494,0.758],[-0.466,0.483],[-0.473,0.214],[-0.516,0.032],[-0.503,0.043],[0.034,0.043],[0.047,0.033],[0.058,0.043],[0.503,0.043],[0.514,0],[0.516,0.066],[0.473,0.223],[0.466,0.448],[0.494,0.751],[0.585,1.178],[0.585,2.609],[0.556,2.788],[0.526,2.822],[-0.004,2.842],[-0.498,2.827],[-0.533,2.817],[-0.554,2.788],[-0.585,2.59]]},"features":{"side":{},"plan":{},"front":{}},"placement":{"side":{"plane":"xy","offset":{}},"plan":{"plane":"xz","offset":{}},"front":{"plane":"zy","offset":{}}},"bounds":{"min":[0.0006,0,-0.585],"max":[1.55,2.981,0.585]},"volume_in3":1.3519,"centroid":[0.7722,1.3788,0],"shell":[0.7721,1.4403,0],"area_in2":25.6089,"triangles":14588,"manifold":true,"slabs":[[0.003,0,-0.508,1.55,0.373,0.508],[0.118,0.373,-0.49,1.427,0.745,0.49],[0.05,0.745,-0.564,1.488,1.118,0.564],[0.001,1.118,-0.585,1.542,2.981,0.585]],"slots":["body"]},"magpul-mlok-polymer-rail-section-11-slot":{"part":"magpul-mlok-polymer-rail-section-11-slot","model":"magpul-mlok-polymer-rail-section-11-slot.glb","script":"magpul_mlok_polymer_rail_section_11_slot.py","inputs":{"magpul-mlok-polymer-rail-section-11-slot.counterbore_diameter":0.41,"magpul-mlok-polymer-rail-section-11-slot.counterbore_floor":0.12,"magpul-mlok-polymer-rail-section-11-slot.end_bevel_length":0.26,"magpul-mlok-polymer-rail-section-11-slot.end_corner_chamfer":0.13,"magpul-mlok-polymer-rail-section-11-slot.end_face_height":0.08,"magpul-mlok-polymer-rail-section-11-slot.height":0.33,"magpul-mlok-polymer-rail-section-11-slot.hole_diameter":0.2,"magpul-mlok-polymer-rail-section-11-slot.hole_pitches":8,"magpul-mlok-polymer-rail-section-11-slot.length":4.706,"magpul-mlok-polymer-rail-section-11-slot.middle_hole_pitches":4,"magpul-mlok-polymer-rail-section-11-slot.neck_foot_above_face":0.055,"magpul-mlok-polymer-rail-section-11-slot.neck_top_below_top":0.2,"magpul-mlok-polymer-rail-section-11-slot.rail_slot0_x":0.383,"magpul-mlok-polymer-rail-section-11-slot.rail_slots":11,"magpul-mlok-polymer-rail-section-11-slot.rear_hole_slot":2,"magpul-mlok-polymer-rail-section-11-slot.screw_head_diameter":0.34,"magpul-mlok-polymer-rail-section-11-slot.screw_head_height":0.06,"magpul-mlok-polymer-rail-section-11-slot.width":0.79,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{},"features":{},"placement":{},"bounds":{"min":[0,0,-0.4175],"max":[4.706,0.33,0.4175]},"volume_in3":0.8611,"centroid":[2.353,0.1383,0],"shell":[2.353,0.147,0],"area_in2":13.9346,"triangles":7664,"manifold":true,"slabs":[[0,0,-0.417,4.706,0.33,0.417]],"slots":["body","screws"]},"magpul-mlok-polymer-rail-section-3-slot":{"part":"magpul-mlok-polymer-rail-section-3-slot","model":"magpul-mlok-polymer-rail-section-3-slot.glb","script":"magpul_mlok_polymer_rail_section_3_slot.py","inputs":{"magpul-mlok-polymer-rail-section-3-slot.counterbore_diameter":0.43,"magpul-mlok-polymer-rail-section-3-slot.counterbore_floor":0.12,"magpul-mlok-polymer-rail-section-3-slot.end_bevel_length":0.195,"magpul-mlok-polymer-rail-section-3-slot.end_corner_chamfer":0.13,"magpul-mlok-polymer-rail-section-3-slot.end_face_height":0.08,"magpul-mlok-polymer-rail-section-3-slot.height":0.33,"magpul-mlok-polymer-rail-section-3-slot.hole_diameter":0.21,"magpul-mlok-polymer-rail-section-3-slot.hole_pitches":2,"magpul-mlok-polymer-rail-section-3-slot.length":1.575,"magpul-mlok-polymer-rail-section-3-slot.neck_foot_above_face":0.055,"magpul-mlok-polymer-rail-section-3-slot.neck_top_below_top":0.2,"magpul-mlok-polymer-rail-section-3-slot.rail_slot0_x":0.3935,"magpul-mlok-polymer-rail-section-3-slot.rail_slots":3,"magpul-mlok-polymer-rail-section-3-slot.rear_hole_slot":1,"magpul-mlok-polymer-rail-section-3-slot.screw_head_diameter":0.396,"magpul-mlok-polymer-rail-section-3-slot.screw_head_height":0.06,"magpul-mlok-polymer-rail-section-3-slot.width":0.811,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{},"features":{},"placement":{},"bounds":{"min":[0,0,-0.4175],"max":[1.575,0.33,0.4175]},"volume_in3":0.2735,"centroid":[0.7875,0.1356,0],"shell":[0.7875,0.1399,0],"area_in2":5.3504,"triangles":4628,"manifold":true,"slabs":[[0,0,-0.417,1.575,0.33,0.417]],"slots":["body","screws"]},"magpul-mlok-polymer-rail-section-5-slot":{"part":"magpul-mlok-polymer-rail-section-5-slot","model":"magpul-mlok-polymer-rail-section-5-slot.glb","script":"magpul_mlok_polymer_rail_section_5_slot.py","inputs":{"magpul-mlok-polymer-rail-section-5-slot.counterbore_diameter":0.39,"magpul-mlok-polymer-rail-section-5-slot.counterbore_floor":0.12,"magpul-mlok-polymer-rail-section-5-slot.end_bevel_length":0.22,"magpul-mlok-polymer-rail-section-5-slot.end_corner_chamfer":0.13,"magpul-mlok-polymer-rail-section-5-slot.end_face_height":0.08,"magpul-mlok-polymer-rail-section-5-slot.height":0.33,"magpul-mlok-polymer-rail-section-5-slot.hole_diameter":0.2,"magpul-mlok-polymer-rail-section-5-slot.hole_pitches":4,"magpul-mlok-polymer-rail-section-5-slot.length":2.36,"magpul-mlok-polymer-rail-section-5-slot.neck_foot_above_face":0.055,"magpul-mlok-polymer-rail-section-5-slot.neck_top_below_top":0.2,"magpul-mlok-polymer-rail-section-5-slot.rail_slot0_x":0.392,"magpul-mlok-polymer-rail-section-5-slot.rail_slots":5,"magpul-mlok-polymer-rail-section-5-slot.rear_hole_slot":1,"magpul-mlok-polymer-rail-section-5-slot.screw_head_diameter":0.34,"magpul-mlok-polymer-rail-section-5-slot.screw_head_height":0.06,"magpul-mlok-polymer-rail-section-5-slot.width":0.81,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{},"features":{},"placement":{},"bounds":{"min":[0,0,-0.4175],"max":[2.36,0.33,0.4175]},"volume_in3":0.4328,"centroid":[1.18,0.1383,0],"shell":[1.18,0.1437,0],"area_in2":7.3767,"triangles":5076,"manifold":true,"slabs":[[0,0,-0.417,2.36,0.33,0.417]],"slots":["body","screws"]},"magpul-mlok-polymer-rail-section-7-slot":{"part":"magpul-mlok-polymer-rail-section-7-slot","model":"magpul-mlok-polymer-rail-section-7-slot.glb","script":"magpul_mlok_polymer_rail_section_7_slot.py","inputs":{"magpul-mlok-polymer-rail-section-7-slot.counterbore_diameter":0.37,"magpul-mlok-polymer-rail-section-7-slot.counterbore_floor":0.12,"magpul-mlok-polymer-rail-section-7-slot.end_bevel_length":0.163,"magpul-mlok-polymer-rail-section-7-slot.end_corner_chamfer":0.13,"magpul-mlok-polymer-rail-section-7-slot.end_face_height":0.08,"magpul-mlok-polymer-rail-section-7-slot.height":0.316,"magpul-mlok-polymer-rail-section-7-slot.hole_diameter":0.2,"magpul-mlok-polymer-rail-section-7-slot.hole_pitches":6,"magpul-mlok-polymer-rail-section-7-slot.length":3.147,"magpul-mlok-polymer-rail-section-7-slot.neck_foot_above_face":0.055,"magpul-mlok-polymer-rail-section-7-slot.neck_top_below_top":0.2,"magpul-mlok-polymer-rail-section-7-slot.rail_slot0_x":0.3915,"magpul-mlok-polymer-rail-section-7-slot.rail_slots":7,"magpul-mlok-polymer-rail-section-7-slot.rear_hole_slot":1,"magpul-mlok-polymer-rail-section-7-slot.screw_head_diameter":0.34,"magpul-mlok-polymer-rail-section-7-slot.screw_head_height":0.06,"magpul-mlok-polymer-rail-section-7-slot.width":0.8,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{},"features":{},"placement":{},"bounds":{"min":[0,0,-0.4175],"max":[3.147,0.316,0.4175]},"volume_in3":0.5695,"centroid":[1.5735,0.1341,0],"shell":[1.5735,0.1402,0],"area_in2":9.3861,"triangles":5500,"manifold":true,"slabs":[[0,0,-0.417,3.147,0.316,0.417]],"slots":["body","screws"]},"magpul-mlok-polymer-rail-section-9-slot":{"part":"magpul-mlok-polymer-rail-section-9-slot","model":"magpul-mlok-polymer-rail-section-9-slot.glb","script":"magpul_mlok_polymer_rail_section_9_slot.py","inputs":{"magpul-mlok-polymer-rail-section-9-slot.counterbore_diameter":0.4,"magpul-mlok-polymer-rail-section-9-slot.counterbore_floor":0.12,"magpul-mlok-polymer-rail-section-9-slot.end_bevel_length":0.2,"magpul-mlok-polymer-rail-section-9-slot.end_corner_chamfer":0.13,"magpul-mlok-polymer-rail-section-9-slot.end_face_height":0.08,"magpul-mlok-polymer-rail-section-9-slot.height":0.345,"magpul-mlok-polymer-rail-section-9-slot.hole_diameter":0.21,"magpul-mlok-polymer-rail-section-9-slot.hole_pitches":8,"magpul-mlok-polymer-rail-section-9-slot.length":3.912,"magpul-mlok-polymer-rail-section-9-slot.middle_hole_pitches":4,"magpul-mlok-polymer-rail-section-9-slot.neck_foot_above_face":0.055,"magpul-mlok-polymer-rail-section-9-slot.neck_top_below_top":0.2,"magpul-mlok-polymer-rail-section-9-slot.rail_slot0_x":0.38,"magpul-mlok-polymer-rail-section-9-slot.rail_slots":9,"magpul-mlok-polymer-rail-section-9-slot.rear_hole_slot":1,"magpul-mlok-polymer-rail-section-9-slot.screw_head_diameter":0.34,"magpul-mlok-polymer-rail-section-9-slot.screw_head_height":0.06,"magpul-mlok-polymer-rail-section-9-slot.width":0.816,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{},"features":{},"placement":{},"bounds":{"min":[0,0,-0.4175],"max":[3.912,0.345,0.4175]},"volume_in3":0.7487,"centroid":[1.956,0.1451,0],"shell":[1.956,0.1521,-0.0001],"area_in2":12.0626,"triangles":7240,"manifold":true,"slabs":[[0,0,-0.417,3.912,0.345,0.417]],"slots":["body","screws"]},"magpul-mlok-qd-sling-mount":{"part":"magpul-mlok-qd-sling-mount","model":"magpul-mlok-qd-sling-mount.glb","script":"magpul_mlok_qd_sling_mount.py","inputs":{"magpul-mlok-qd-sling-mount.screw_head_diameter":0.272,"magpul-mlok-qd-sling-mount.screw_head_top":0.235,"magpul-mlok-qd-sling-mount.screw_hex":0.15625,"magpul-mlok-qd-sling-mount.screw_seat_height":0.055},"profiles":{"plan":[[0,0.056],[0,-0.053],[0.005,-0.091],[0.024,-0.131],[0.051,-0.163],[0.074,-0.179],[0.097,-0.19],[0.119,-0.197],[0.121,-0.195],[0.125,-0.198],[0.257,-0.209],[0.275,-0.214],[0.28,-0.212],[0.331,-0.219],[0.384,-0.222],[0.431,-0.229],[0.458,-0.235],[0.492,-0.249],[0.519,-0.266],[0.546,-0.276],[0.556,-0.283],[0.559,-0.282],[0.609,-0.296],[0.674,-0.3],[0.722,-0.294],[0.746,-0.287],[0.75,-0.289],[0.756,-0.283],[0.77,-0.282],[0.776,-0.276],[0.805,-0.264],[0.843,-0.242],[0.89,-0.229],[1.011,-0.215],[1.028,-0.216],[1.035,-0.213],[1.089,-0.209],[1.109,-0.205],[1.163,-0.203],[1.169,-0.199],[1.176,-0.203],[1.183,-0.198],[1.205,-0.196],[1.235,-0.186],[1.26,-0.171],[1.29,-0.143],[1.313,-0.098],[1.321,-0.054],[1.321,0.056],[1.314,0.095],[1.296,0.132],[1.261,0.17],[1.227,0.189],[1.224,0.188],[1.217,0.193],[1.19,0.199],[1.149,0.201],[1.143,0.206],[1.137,0.203],[1.113,0.204],[1.075,0.209],[1.068,0.213],[1.064,0.21],[1.026,0.215],[1.009,0.215],[1.004,0.217],[0.886,0.229],[0.837,0.245],[0.783,0.275],[0.759,0.282],[0.751,0.287],[0.749,0.285],[0.742,0.29],[0.698,0.298],[0.644,0.301],[0.617,0.296],[0.614,0.297],[0.569,0.287],[0.553,0.279],[0.54,0.276],[0.485,0.245],[0.482,0.247],[0.475,0.242],[0.435,0.229],[0.429,0.232],[0.412,0.226],[0.401,0.226],[0.375,0.221],[0.371,0.223],[0.325,0.217],[0.32,0.22],[0.314,0.215],[0.307,0.219],[0.301,0.215],[0.266,0.213],[0.24,0.208],[0.236,0.21],[0.179,0.202],[0.172,0.204],[0.167,0.201],[0.132,0.199],[0.081,0.183],[0.053,0.164],[0.028,0.137],[0.005,0.091]],"side":[[0,0.127],[0,0.005],[0.002,0.002],[0.034,0],[1.287,0],[1.32,0.002],[1.321,0.13],[1.22,0.173],[1.185,0.181],[1.128,0.201],[1.117,0.202],[1.098,0.21],[1.093,0.215],[1.091,0.213],[1.074,0.218],[1.041,0.234],[1.012,0.251],[0.981,0.274],[0.942,0.314],[0.914,0.354],[0.408,0.354],[0.376,0.311],[0.352,0.285],[0.311,0.253],[0.281,0.234],[0.211,0.205],[0.174,0.194],[0.171,0.195],[0.16,0.189],[0.101,0.173],[0.004,0.132]],"front":[[-0.3,0.319],[-0.3,0.002],[0,0.001],[0.13,0.003],[0.135,0],[0.137,0.003],[0.3,0.002],[0.3,0.319],[0.265,0.354],[0.197,0.354],[-0.267,0.353]]},"features":{"plan":{"screw_holes":[[[0.376,-0.014],[0.368,-0.042],[0.354,-0.067],[0.334,-0.087],[0.309,-0.101],[0.281,-0.109],[0.253,-0.109],[0.225,-0.101],[0.2,-0.087],[0.18,-0.067],[0.166,-0.042],[0.158,-0.014],[0.158,0.014],[0.166,0.042],[0.18,0.067],[0.2,0.087],[0.225,0.101],[0.253,0.109],[0.281,0.109],[0.309,0.101],[0.334,0.087],[0.354,0.067],[0.368,0.042],[0.376,0.014]],[[1.163,-0.014],[1.156,-0.042],[1.141,-0.067],[1.121,-0.087],[1.096,-0.101],[1.069,-0.109],[1.04,-0.109],[1.013,-0.101],[0.988,-0.087],[0.968,-0.067],[0.953,-0.042],[0.946,-0.014],[0.946,0.014],[0.953,0.042],[0.968,0.067],[0.988,0.087],[1.013,0.101],[1.04,0.109],[1.069,0.109],[1.096,0.101],[1.121,0.087],[1.141,0.067],[1.156,0.042],[1.163,0.014]]],"counterbores":[[[0.427,-0.016],[0.421,-0.047],[0.409,-0.076],[0.391,-0.102],[0.369,-0.124],[0.343,-0.142],[0.314,-0.154],[0.283,-0.16],[0.251,-0.16],[0.22,-0.154],[0.191,-0.142],[0.165,-0.124],[0.143,-0.102],[0.125,-0.076],[0.113,-0.047],[0.107,-0.016],[0.107,0.016],[0.113,0.047],[0.125,0.076],[0.143,0.102],[0.165,0.124],[0.191,0.142],[0.22,0.154],[0.251,0.16],[0.283,0.16],[0.314,0.154],[0.343,0.142],[0.369,0.124],[0.391,0.102],[0.409,0.076],[0.421,0.047],[0.427,0.016]],[[1.214,-0.016],[1.208,-0.047],[1.196,-0.076],[1.179,-0.102],[1.156,-0.124],[1.13,-0.142],[1.101,-0.154],[1.07,-0.16],[1.039,-0.16],[1.008,-0.154],[0.978,-0.142],[0.952,-0.124],[0.93,-0.102],[0.912,-0.076],[0.9,-0.047],[0.894,-0.016],[0.894,0.016],[0.9,0.047],[0.912,0.076],[0.93,0.102],[0.952,0.124],[0.978,0.142],[1.008,0.154],[1.039,0.16],[1.07,0.16],[1.101,0.154],[1.13,0.142],[1.156,0.124],[1.179,0.102],[1.196,0.076],[1.208,0.047],[1.214,0.016]]],"bore":[[[0.847,-0.018],[0.839,-0.054],[0.825,-0.088],[0.805,-0.118],[0.779,-0.144],[0.749,-0.165],[0.715,-0.179],[0.679,-0.186],[0.642,-0.186],[0.606,-0.179],[0.573,-0.165],[0.542,-0.144],[0.516,-0.118],[0.496,-0.088],[0.482,-0.054],[0.475,-0.018],[0.475,0.018],[0.482,0.054],[0.496,0.088],[0.516,0.119],[0.542,0.144],[0.573,0.165],[0.606,0.179],[0.642,0.186],[0.679,0.186],[0.715,0.179],[0.749,0.165],[0.779,0.144],[0.805,0.119],[0.825,0.088],[0.839,0.054],[0.847,0.018]]],"bore_lead":[[[0.858,-0.019],[0.85,-0.057],[0.835,-0.093],[0.814,-0.126],[0.786,-0.153],[0.754,-0.175],[0.718,-0.19],[0.68,-0.197],[0.641,-0.197],[0.603,-0.19],[0.567,-0.175],[0.535,-0.153],[0.507,-0.126],[0.486,-0.093],[0.471,-0.057],[0.463,-0.019],[0.463,0.02],[0.471,0.058],[0.486,0.094],[0.507,0.126],[0.535,0.153],[0.567,0.175],[0.603,0.19],[0.641,0.197],[0.68,0.197],[0.718,0.19],[0.754,0.175],[0.786,0.153],[0.814,0.126],[0.835,0.094],[0.85,0.058],[0.858,0.02]]],"boss_face":[[[0.925,-0.021],[0.918,-0.062],[0.905,-0.101],[0.886,-0.138],[0.862,-0.172],[0.833,-0.201],[0.799,-0.226],[0.762,-0.245],[0.722,-0.258],[0.681,-0.264],[0.64,-0.264],[0.599,-0.258],[0.559,-0.245],[0.522,-0.226],[0.489,-0.201],[0.459,-0.172],[0.435,-0.138],[0.416,-0.101],[0.403,-0.062],[0.397,-0.021],[0.397,0.021],[0.403,0.062],[0.416,0.101],[0.435,0.138],[0.459,0.172],[0.489,0.201],[0.522,0.226],[0.559,0.245],[0.599,0.257],[0.64,0.264],[0.681,0.264],[0.722,0.257],[0.762,0.245],[0.799,0.226],[0.833,0.201],[0.862,0.172],[0.886,0.138],[0.905,0.101],[0.918,0.062],[0.925,0.021]]],"boss":[[[0.96,-0.024],[0.952,-0.07],[0.938,-0.115],[0.916,-0.157],[0.889,-0.195],[0.855,-0.228],[0.817,-0.256],[0.775,-0.277],[0.731,-0.292],[0.684,-0.299],[0.637,-0.299],[0.591,-0.292],[0.546,-0.277],[0.504,-0.256],[0.466,-0.228],[0.433,-0.195],[0.405,-0.157],[0.383,-0.115],[0.369,-0.07],[0.362,-0.024],[0.362,0.024],[0.369,0.07],[0.383,0.115],[0.405,0.157],[0.433,0.195],[0.466,0.228],[0.504,0.256],[0.546,0.277],[0.591,0.292],[0.637,0.299],[0.684,0.299],[0.731,0.292],[0.775,0.277],[0.817,0.256],[0.855,0.228],[0.889,0.195],[0.916,0.157],[0.938,0.115],[0.952,0.07],[0.96,0.024]]]},"side":{"wall_top":[[[1.319,0.131],[1.316,0.131],[1.304,0.134],[1.292,0.137],[1.28,0.14],[1.268,0.143],[1.257,0.146],[1.245,0.151],[1.233,0.154],[1.221,0.158],[1.209,0.162],[1.198,0.166],[1.186,0.17],[1.174,0.175],[1.162,0.178],[1.151,0.184],[1.139,0.188],[1.127,0.192],[1.115,0.196],[1.103,0.2],[1.092,0.204],[1.08,0.208],[1.068,0.212],[1.056,0.216],[1.044,0.221],[1.033,0.225],[1.021,0.231],[1.009,0.236],[0.997,0.241],[0.985,0.246],[0.974,0.252],[0.962,0.259],[0.95,0.264],[0.938,0.271],[0.927,0.277],[0.915,0.282],[0.903,0.289],[0.891,0.296],[0.879,0.301],[0.867,0.307],[0.852,0.312],[0.841,0.315],[0.833,0.316],[0.812,0.319]],[[0.001,0.132],[0.005,0.132],[0.016,0.133],[0.028,0.136],[0.04,0.139],[0.052,0.143],[0.064,0.146],[0.075,0.15],[0.087,0.154],[0.099,0.158],[0.111,0.162],[0.123,0.166],[0.134,0.17],[0.146,0.175],[0.158,0.178],[0.17,0.183],[0.181,0.188],[0.193,0.192],[0.205,0.196],[0.217,0.2],[0.229,0.205],[0.24,0.208],[0.252,0.212],[0.264,0.217],[0.276,0.221],[0.288,0.226],[0.299,0.231],[0.311,0.236],[0.323,0.241],[0.335,0.247],[0.346,0.252],[0.358,0.258],[0.37,0.264],[0.382,0.27],[0.394,0.277],[0.405,0.281],[0.418,0.289],[0.431,0.296],[0.443,0.302],[0.455,0.308],[0.468,0.312],[0.479,0.315],[0.49,0.316],[0.509,0.319]]]},"front":{}},"placement":{"plan":{"plane":"xz","offset":{}},"side":{"plane":"xy","offset":{}},"front":{"plane":"zy","offset":{}}},"bounds":{"min":[0,0,-0.2996],"max":[1.3213,0.354,0.2997]},"volume_in3":0.109,"centroid":[0.6607,0.1376,0.0001],"shell":[0.6607,0.1316,0],"area_in2":3.2284,"triangles":26850,"manifold":true,"slabs":[[0,0,-0.218,0.33,0.267,0.218],[0.33,0,-0.3,0.991,0.354,0.3],[0.991,0,-0.218,1.321,0.267,0.218]],"slots":["body","screws"]},"magpul-mlok-rail-cover-type-2":{"part":"magpul-mlok-rail-cover-type-2","model":"magpul-mlok-rail-cover-type-2.glb","script":"magpul_mlok_rail_cover_type_2.py","inputs":{},"profiles":{"front":[[-0.519,-0.089],[-0.515,-0.105],[-0.51,-0.11],[-0.504,-0.111],[-0.453,-0.077],[-0.369,-0.015],[-0.327,0.011],[-0.305,0],[-0.143,0.001],[-0.135,-0.001],[-0.127,0.001],[0.306,0],[0.314,0.001],[0.327,0.01],[0.334,0.01],[0.499,-0.108],[0.516,-0.108],[0.519,-0.099],[0.519,-0.07],[0.513,-0.053],[0.391,0.062],[0.357,0.087],[0.321,0.104],[0.287,0.113],[0.283,0.111],[0.274,0.115],[0.261,0.114],[0.257,0.117],[0.236,0.121],[0.23,0.116],[0.218,0.123],[0.191,0.124],[0.165,0.129],[0.143,0.128],[0.092,0.135],[0.079,0.133],[0.047,0.136],[0.044,0.134],[0.04,0.136],[0.034,0.134],[0.032,0.136],[-0.032,0.136],[-0.035,0.134],[-0.041,0.136],[-0.044,0.134],[-0.048,0.136],[-0.052,0.134],[-0.108,0.134],[-0.143,0.128],[-0.166,0.129],[-0.182,0.125],[-0.218,0.123],[-0.23,0.117],[-0.237,0.121],[-0.257,0.117],[-0.261,0.114],[-0.274,0.115],[-0.322,0.104],[-0.347,0.09],[-0.35,0.091],[-0.392,0.062],[-0.513,-0.053],[-0.517,-0.062]],"side":[[0,0.067],[0,0.06],[0.003,0.056],[0.001,-0.061],[0.022,-0.078],[0.096,-0.108],[0.116,-0.11],[0.49,-0.111],[1.287,-0.111],[1.459,-0.109],[1.541,-0.078],[1.555,-0.067],[1.557,-0.06],[1.56,-0.039],[1.56,0.034],[1.557,0.054],[1.559,0.084],[1.556,0.088],[1.555,0.127],[1.553,0.132],[1.545,0.136],[0.024,0.136],[0.008,0.133],[0.004,0.071]],"plan":[[0,-0.386],[0.001,-0.447],[0.006,-0.46],[0.018,-0.472],[0.077,-0.506],[0.085,-0.507],[0.092,-0.513],[0.113,-0.519],[1.437,-0.52],[1.476,-0.511],[1.508,-0.491],[1.528,-0.482],[1.551,-0.465],[1.557,-0.457],[1.559,-0.447],[1.56,-0.165],[1.556,-0.144],[1.556,0.148],[1.56,0.162],[1.56,0.434],[1.555,0.46],[1.544,0.472],[1.472,0.513],[1.453,0.52],[0.105,0.52],[0.071,0.505],[0.019,0.475],[0.007,0.464],[0.001,0.451],[0.004,-0.144],[0.001,-0.152]]},"features":{"front":{"tab":[[[-0.229,0.12],[-0.194,0.071],[0.194,0.071],[0.229,0.12]]],"channel":[[[-0.234,0.121],[-0.201,0.071],[0.201,0.071],[0.234,0.121]]]},"side":{"windows":[[[0.314,0.114],[0.458,0.114],[0.458,0.017],[0.314,0.017]],[[1.101,0.114],[1.245,0.114],[1.245,0.017],[1.101,0.017]]]},"plan":{"tab":[[[0.001,0.229],[1.561,0.229],[1.561,-0.226],[0.001,-0.226]]],"windows":[[[0.313,0.439],[0.459,0.439],[0.459,0.229],[0.313,0.229]],[[1.1,0.439],[1.247,0.439],[1.247,0.229],[1.1,0.229]],[[0.313,-0.226],[0.459,-0.226],[0.459,-0.436],[0.313,-0.436]],[[1.1,-0.226],[1.247,-0.226],[1.247,-0.436],[1.1,-0.436]]],"window_floors":[[[0.337,0.439],[0.434,0.439],[0.434,0.229],[0.337,0.229]],[[1.124,0.439],[1.222,0.439],[1.222,0.229],[1.124,0.229]],[[0.337,-0.226],[0.434,-0.226],[0.434,-0.436],[0.337,-0.436]],[[1.124,-0.226],[1.222,-0.226],[1.222,-0.436],[1.124,-0.436]]]}},"placement":{"front":{"plane":"zy","offset":{}},"side":{"plane":"xy","offset":{}},"plan":{"plane":"xz","offset":{}}},"bounds":{"min":[0,-0.1095,-0.519],"max":[1.56,0.136,0.519]},"volume_in3":0.1706,"centroid":[0.7805,0.043,0.0001],"shell":[0.7804,0.0332,0.0001],"area_in2":4.2199,"triangles":11736,"manifold":true,"slabs":[[0,-0.109,-0.519,1.56,0.136,0.519]],"slots":["body"]},"magpul-moe-carbine":{"part":"magpul-moe-carbine","model":"magpul-moe-carbine.glb","script":"magpul_moe_carbine.py","inputs":{"bcm-receiver-extension.tube_front_behind_pin":0.669,"bcm-receiver-extension.tube_length":7.25,"magpul-moe-carbine.bore_diameter":1.158,"magpul-moe-carbine.butt_behind_pin_pos1":8.696,"magpul-moe-carbine.frame_width":0.69,"magpul-moe-carbine.pad_check_depth":0.033,"magpul-moe-carbine.pad_check_pitch":0.122,"magpul-moe-carbine.pad_check_top":1.27,"magpul-moe-carbine.rail_channel_floor_below_axis":0.874,"magpul-moe-carbine.rail_channel_width":0.49,"magpul-moe-carbine.tube_axis_below_top":0.706},"profiles":{"side":[[0,-0.76],[0.151,-1.558],[0.165,-1.645],[0.156,-1.682],[0.174,-1.7],[0.188,-1.765],[0.358,-2.866],[0.464,-3.766],[0.56,-4.982],[0.631,-5.09],[0.727,-5.145],[0.879,-5.149],[0.911,-5.181],[0.952,-5.191],[1.255,-5.191],[1.434,-5.181],[1.554,-5.126],[1.666,-4.991],[1.698,-4.872],[1.765,-4.787],[3.197,-3.795],[4.431,-2.965],[4.592,-2.841],[4.844,-2.689],[6.281,-1.716],[6.34,-1.693],[6.68,-1.693],[6.753,-1.735],[6.808,-1.739],[6.928,-1.712],[6.953,-1.687],[6.967,-1.613],[7.013,-0.659],[6.99,-0.278],[6.962,-0.122],[6.937,-0.087],[6.854,-0.05],[0.842,-0.05],[0.741,-0.046],[0.682,0],[0.475,0],[0.425,-0.014],[0.388,-0.05],[0.273,-0.055],[0.117,-0.092],[0.064,-0.145],[0.018,-0.356]],"front":[[-0.848,-1.009],[-0.699,-1.911],[-0.609,-2.994],[-0.59,-3.69],[-0.622,-4.702],[-0.603,-4.85],[-0.519,-5.024],[-0.4,-5.131],[-0.329,-5.169],[-0.142,-5.215],[0.161,-5.215],[0.348,-5.163],[0.451,-5.092],[0.577,-4.947],[0.616,-4.792],[0.609,-4.148],[0.596,-4.122],[0.603,-3.606],[0.59,-3.561],[0.603,-3.548],[0.596,-3.394],[0.609,-3.368],[0.603,-3.2],[0.616,-3.181],[0.622,-2.826],[0.641,-2.73],[0.648,-2.459],[0.661,-2.446],[0.654,-2.395],[0.674,-2.311],[0.706,-1.879],[0.738,-1.782],[0.77,-1.466],[0.802,-1.312],[0.796,-1.273],[0.835,-1.112],[0.848,-0.97],[0.815,-0.822],[0.68,-0.448],[0.564,-0.255],[0.425,-0.129],[0.322,-0.071],[0.18,-0.019],[0,-0.006],[-0.013,0],[-0.116,-0.006],[-0.335,-0.077],[-0.413,-0.122],[-0.545,-0.235],[-0.622,-0.338],[-0.667,-0.429],[-0.712,-0.57],[-0.777,-0.706]]},"features":{"side":{"through":[[[4.846,-1.053],[4.865,-1.017],[4.922,-0.978],[5.771,-0.973],[5.829,-1.049],[5.81,-1.118],[5.757,-1.152],[5.239,-1.157],[4.876,-1.157],[4.851,-1.122]],[[1.368,-1.099],[1.368,-1.058],[1.386,-1.012],[1.42,-0.987],[2.37,-0.991],[2.432,-1.04],[2.446,-1.113],[2.416,-1.161],[2.361,-1.17],[1.443,-1.17],[1.391,-1.14]],[[1.285,-1.944],[1.294,-1.879],[1.361,-1.785],[1.439,-1.744],[1.558,-1.73],[2.875,-1.716],[2.887,-1.728],[2.857,-1.749],[2.37,-1.941],[2.322,-1.976],[2.286,-2.035],[2.281,-2.077],[2.308,-2.182],[2.304,-2.237],[2.318,-2.269],[2.347,-2.286],[3.678,-1.923],[4.101,-1.891],[4.126,-1.833],[4.137,-1.822],[4.153,-1.838],[4.19,-1.911],[4.199,-2.035],[4.158,-2.146],[4.105,-2.208],[1.898,-3.951],[1.783,-4.002],[1.71,-4.002],[1.636,-3.979],[1.556,-3.912],[1.515,-3.83],[1.432,-3.018]],[[0.959,-2.343],[0.964,-2.269],[1.021,-2.226],[1.081,-2.23],[1.129,-2.274],[1.166,-2.467],[1.28,-3.38],[1.276,-3.444],[1.246,-3.474],[1.2,-3.488],[1.136,-3.465],[1.097,-3.398],[1.028,-2.793]],[[2.478,-3.747],[2.504,-3.708],[3.417,-3.038],[3.481,-3.029],[3.534,-3.063],[3.543,-3.132],[3.504,-3.176],[2.586,-3.837],[2.531,-3.832],[2.487,-3.793]],[[1.198,-4.84],[1.198,-4.78],[1.214,-4.764],[1.393,-4.768],[1.455,-4.835],[1.411,-4.869],[1.237,-4.869]]],"buttpad":[[[-1.14,0.507],[0.383,0.507],[0.374,-0.021],[0.296,-0.457],[0.305,-0.916],[0.383,-1.375],[0.489,-1.833],[0.567,-2.292],[0.649,-2.751],[0.718,-3.21],[0.764,-3.669],[0.81,-4.128],[0.856,-4.587],[0.888,-5.023],[0.906,-5.712],[-1.14,-5.712]]],"frame":[[[0.773,-1.558],[4.872,-1.558],[4.872,-1.925],[8.13,-1.925],[8.13,-5.712],[1.255,-5.712],[1.237,-5.023],[1.205,-4.587],[1.159,-4.128],[1.113,-3.669],[1.067,-3.21],[0.998,-2.751],[0.916,-2.292],[0.838,-1.833]]]},"front":{}},"placement":{"side":{"plane":"xy","offset":{"y":"tube_axis_below_top"}},"front":{"plane":"zy","offset":{"y":"tube_axis_below_top"}}},"bounds":{"min":[0,-4.485,-0.848],"max":[7.013,0.706,0.848]},"volume_in3":14.858,"centroid":[2.793,-1.232,0.0018],"shell":[2.8173,-1.0569,0.0013],"area_in2":120.6502,"triangles":57642,"manifold":true,"slabs":[[0,-2.388,-0.848,0.39,0.658,0.848],[0.39,-4.485,-0.848,1.558,0.706,0.848],[1.558,-4.415,-0.843,1.948,0.656,0.848],[1.948,-3.954,-0.844,2.338,0.656,0.848],[2.338,-3.684,-0.848,2.727,0.656,0.848],[2.727,-3.414,-0.848,3.117,0.656,0.848],[3.117,-3.144,-0.848,3.507,0.656,0.848],[3.507,-2.881,-0.848,3.896,0.656,0.848],[3.896,-2.619,-0.848,4.286,0.656,0.848],[4.286,-2.357,-0.848,4.675,0.656,0.848],[4.675,-2.085,-0.848,5.065,0.656,0.848],[5.065,-1.833,-0.84,5.455,0.656,0.848],[5.455,-1.57,-0.848,5.844,0.656,0.848],[5.844,-1.306,-0.848,6.234,0.656,0.848],[6.234,-1.042,-0.848,7.013,0.656,0.848]],"slots":["body","buttpad"]},"magpul-moe-k2-plus":{"part":"magpul-moe-k2-plus","model":"magpul-moe-k2-plus.glb","script":"magpul_moe_k2_plus.py","inputs":{"magpul-moe-k2-plus.base_lip_height":0.166,"magpul-moe-k2-plus.base_tab_front_foot_u":1.105,"magpul-moe-k2-plus.base_tab_front_top_u":1.01,"magpul-moe-k2-plus.base_tab_height":0.296,"magpul-moe-k2-plus.base_tab_rear_foot_u":0.065,"magpul-moe-k2-plus.base_tab_rear_top_u":0.21,"magpul-moe-k2-plus.beavertail_edge_round":0.111,"magpul-moe-k2-plus.detail_relief":0.02,"magpul-moe-k2-plus.grip_angle":17.89,"magpul-moe-k2-plus.latch_end_gap":0.035,"magpul-moe-k2-plus.latch_height":0.132,"magpul-moe-k2-plus.latch_window_depth":0.05,"magpul-moe-k2-plus.latch_window_front_u":0.93,"magpul-moe-k2-plus.latch_window_height":0.18,"magpul-moe-k2-plus.latch_window_rear_u":0.243,"magpul-moe-k2-plus.logo_plate_corner_r":0.07,"magpul-moe-k2-plus.logo_plate_height":0.238,"magpul-moe-k2-plus.logo_plate_length":0.866,"magpul-moe-k2-plus.logo_plate_rear_x":0.13,"magpul-moe-k2-plus.logo_plate_top_y":-0.154,"magpul-moe-k2-plus.lug_slot_width":0.425,"magpul-moe-k2-plus.relief_band_width":0.119,"magpul-moe-k2-plus.relief_edge_rear_x":-0.3,"magpul-moe-k2-plus.relief_edge_rear_y":-1.017,"magpul-moe-k2-plus.relief_floor_front_x":0.95,"magpul-moe-k2-plus.relief_floor_front_y":-0.756,"magpul-moe-k2-plus.relief_floor_low_x":0.4,"magpul-moe-k2-plus.relief_floor_low_y":-0.985,"magpul-moe-k2-plus.relief_floor_rear_x":-0.18,"magpul-moe-k2-plus.relief_floor_rear_y":-0.787,"magpul-moe-k2-plus.relief_floor_rise":0.05,"magpul-moe-k2-plus.relief_top_front_x":0.995,"magpul-moe-k2-plus.relief_top_front_y":-0.673,"magpul-moe-k2-plus.relief_top_rear_x":-0.162,"magpul-moe-k2-plus.relief_top_rear_y":-0.487,"magpul-moe-k2-plus.seat_x":-0.155,"magpul-moe-k2-plus.strap_face_width":0.75,"magpul-moe-k2-plus.thickness":1.2,"magpul-moe-k2-plus.top_block_width":0.88,"std.ar15.deck_y":0.2485,"std.ar15.grip_lug_depth":0.93,"std.ar15.grip_lug_face_angle":60,"std.ar15.grip_lug_face_from_pin":1.228,"std.ar15.grip_lug_front_from_rear_face":2.3,"std.ar15.grip_lug_length":1.25,"std.ar15.grip_lug_width":0.375,"std.ar15.grip_seat_below_deck":1.318,"std.ar15.rear_underside_arc_center_below_seat":0.1928,"std.ar15.rear_underside_arc_center_x":-1.0238,"std.ar15.rear_underside_arc_r_fullest":0.716,"std.ar15.rear_underside_round_r":0.44,"std.ar15.receiver_rear_x":-1.125},"profiles":{"side":[[-1.631,-3.508],[-1.627,-3.543],[-1.594,-3.589],[-1.458,-3.668],[-1.318,-3.72],[-1.02,-3.82],[-0.994,-3.82],[-0.972,-3.798],[-0.919,-3.842],[-0.433,-3.994],[-0.35,-4.015],[-0.319,-4.011],[-0.297,-4.037],[0.184,-4.15],[0.237,-4.15],[0.307,-4.115],[0.348,-4.064],[0.392,-3.977],[0.387,-3.889],[0.313,-3.776],[0.291,-3.701],[0.291,-3.609],[0.321,-3.509],[0.312,-3.478],[0.343,-3.438],[0.343,-3.39],[0.369,-3.351],[0.364,-3.311],[0.395,-3.268],[0.39,-3.224],[0.421,-3.184],[0.416,-3.141],[0.443,-3.11],[0.443,-3.057],[0.473,-3.009],[0.464,-2.974],[0.499,-2.926],[0.49,-2.891],[0.521,-2.847],[0.516,-2.808],[0.547,-2.76],[0.543,-2.72],[0.573,-2.681],[0.564,-2.641],[0.599,-2.593],[0.59,-2.554],[0.625,-2.51],[0.616,-2.471],[0.651,-2.422],[0.643,-2.387],[0.677,-2.335],[0.669,-2.3],[0.699,-2.26],[0.695,-2.217],[0.725,-2.182],[0.721,-2.129],[0.751,-2.094],[0.742,-2.05],[0.777,-2.006],[0.769,-1.967],[0.795,-1.941],[0.803,-1.914],[0.795,-1.879],[0.821,-1.853],[0.83,-1.822],[0.821,-1.796],[0.843,-1.774],[0.856,-1.744],[0.847,-1.709],[0.882,-1.66],[0.873,-1.621],[0.899,-1.59],[0.943,-1.476],[1.01,-1.391],[1.063,-1.351],[1.141,-1.316],[1.203,-1.307],[1.255,-1.312],[1.275,-1.296],[1.292,-1.257],[1.314,-1.152],[1.322,-1.056],[1.318,-0.99],[1.327,-0.977],[1.317,-0.723],[1.33,-0.307],[1.321,-0.233],[1.286,-0.145],[1.222,-0.064],[1.139,-0.012],[1.086,0.001],[0.202,-0.001],[0.132,0.008],[0.073,0.062],[0.038,0.154],[-0.037,0.285],[-0.162,0.427],[-0.289,0.519],[-0.372,0.562],[-0.508,0.606],[-0.626,0.623],[-0.71,0.623],[-0.793,0.605],[-0.941,0.57],[-0.97,0.546],[-0.978,0.458],[-0.974,0.226],[-0.96,0.191],[-0.936,0.167],[-0.625,-0.081],[-0.526,-0.197],[-0.478,-0.302],[-0.456,-0.407],[-0.456,-0.508],[-0.469,-0.578],[-0.499,-0.665],[-0.543,-0.74],[-0.73,-0.964],[-0.774,-1.038],[-0.787,-1.073],[-0.783,-1.091],[-0.813,-1.121],[-0.813,-1.178],[-0.839,-1.196],[-0.848,-1.218],[-0.844,-1.261],[-0.874,-1.288],[-0.874,-1.345],[-0.896,-1.362],[-0.909,-1.402],[-0.9,-1.428],[-0.931,-1.458],[-0.931,-1.511],[-0.961,-1.546],[-0.961,-1.599],[-0.983,-1.616],[-0.996,-1.656],[-0.991,-1.682],[-1.018,-1.713],[-1.018,-1.765],[-1.048,-1.796],[-1.048,-1.848],[-1.074,-1.875],[-1.083,-1.91],[-1.078,-1.931],[-1.1,-1.953],[-1.109,-1.984],[-1.105,-2.015],[-1.131,-2.041],[-1.139,-2.072],[-1.135,-2.098],[-1.161,-2.129],[-1.17,-2.172],[-1.161,-2.181],[-1.187,-2.207],[-1.196,-2.234],[-1.192,-2.264],[-1.218,-2.295],[-1.226,-2.326],[-1.222,-2.352],[-1.248,-2.383],[-1.252,-2.435],[-1.279,-2.47],[-1.279,-2.518],[-1.3,-2.536],[-1.313,-2.58],[-1.309,-2.602],[-1.335,-2.637],[-1.335,-2.685],[-1.357,-2.702],[-1.366,-2.724],[-1.366,-2.768],[-1.392,-2.803],[-1.396,-2.851],[-1.414,-2.869],[-1.422,-2.895],[-1.422,-2.934],[-1.444,-2.956],[-1.453,-3.018],[-1.47,-3.035],[-1.479,-3.062],[-1.479,-3.101],[-1.501,-3.123],[-1.509,-3.184],[-1.531,-3.215],[-1.535,-3.263],[-1.588,-3.355],[-1.587,-3.39]],"rear":[[-0.6,-4.309],[-0.579,-4.355],[-0.501,-4.416],[-0.459,-4.432],[-0.262,-4.449],[0.022,-4.452],[0.476,-4.43],[0.574,-4.363],[0.597,-4.331],[0.592,-4.233],[0.572,-4.211],[0.569,-4.167],[0.592,-4.128],[0.594,-3.69],[0.581,-3.679],[0.592,-3.629],[0.6,-1.797],[0.592,-1.786],[0.589,-1.407],[0.477,-1.126],[0.452,-1.02],[0.455,-0.174],[0.447,-0.063],[0.43,-0.026],[0.404,-0.006],[0.365,-0.003],[0.29,-0.07],[0.187,-0.125],[0.064,-0.161],[-0.019,-0.167],[-0.203,-0.117],[-0.365,-0.003],[-0.401,0],[-0.436,-0.026],[-0.455,-0.113],[-0.452,-1.029],[-0.469,-1.057],[-0.475,-1.121],[-0.575,-1.357],[-0.594,-1.441],[-0.592,-4.13],[-0.575,-4.206],[-0.592,-4.236]],"plan":[[-2.729,-0.176],[-2.723,-0.296],[-2.712,-0.316],[-2.492,-0.431],[-2.329,-0.483],[-2.174,-0.498],[-1.956,-0.565],[-1.749,-0.6],[-1.353,-0.58],[-1.073,-0.536],[-1.05,-0.548],[-1.024,-0.527],[-1.003,-0.542],[-0.995,-0.521],[-0.907,-0.486],[-0.756,-0.486],[-0.447,-0.451],[-0.275,-0.414],[-0.025,-0.329],[0,-0.272],[-0.012,0.051],[-0.003,0.234],[-0.033,0.28],[-0.368,0.382],[-0.572,0.417],[-0.782,0.434],[-0.84,0.486],[-0.919,0.516],[-1.292,0.559],[-1.35,0.571],[-1.379,0.591],[-1.618,0.6],[-1.737,0.594],[-1.752,0.583],[-1.947,0.553],[-2.442,0.402],[-2.71,0.297],[-2.726,0.261]]},"features":{"side":{},"rear":{},"plan":{}},"placement":{"side":{"plane":"xy","offset":{}},"rear":{"plane":"zy","offset":{}},"plan":{"plane":"xz","offset":{}}},"bounds":{"min":[-1.631,-4.15,-0.6],"max":[1.33,0.623,0.6]},"volume_in3":8.067,"centroid":[-0.1946,-2.0562,-0.0002],"shell":[-0.1825,-2.0572,0.0001],"area_in2":36.0767,"triangles":31944,"manifold":true,"receiver":{"slot":{"width":0.425,"clear_of_lug":0.025,"rear_x":0.055,"floor_at_rear_y":-0.3196,"foot_x":1.1555,"bottom_y":-0.955},"scoop":{"axis_x":-0.8688,"axis_y":-0.1928,"on_centre_plane_r":0.691,"across_r":0.465}},"slabs":[[-1.217,-4.15,-0.6,0.392,-3.752,0.6],[-1.631,-3.752,-0.6,0.367,-3.355,0.6],[-1.588,-3.355,-0.594,0.477,-2.957,0.594],[-1.444,-2.957,-0.596,0.599,-2.559,0.596],[-1.307,-2.559,-0.598,0.725,-2.161,0.598],[-1.168,-2.161,-0.599,0.848,-1.764,0.599],[-1.018,-1.764,-0.6,1.043,-1.366,0.6],[-0.897,-1.366,-0.6,1.327,-0.968,0.6],[-0.732,-0.968,-0.574,1.327,-0.57,0.57],[-0.543,-0.57,-0.444,1.33,-0.172,0.444],[-0.974,-0.172,-0.441,1.297,0.225,0.441],[-0.978,0.225,-0.441,0.001,0.623,0.441]],"slots":["body","base"]},"magpul-moe-mlok-handguard-carbine":{"part":"magpul-moe-mlok-handguard-carbine","model":"magpul-moe-mlok-handguard-carbine.glb","script":"magpul_moe_mlok_handguard_carbine.py","inputs":{"magpul-moe-mlok-handguard-carbine.bottom_half_width":0.45,"magpul-moe-mlok-handguard-carbine.face_flat":0.62,"magpul-moe-mlok-handguard-carbine.front_flange_od":1.36,"magpul-moe-mlok-handguard-carbine.front_wall_x":6.03,"magpul-moe-mlok-handguard-carbine.heat_shield_thickness":0.03,"magpul-moe-mlok-handguard-carbine.length":7.1,"magpul-moe-mlok-handguard-carbine.mlok_bottom_face_distance":1.19,"magpul-moe-mlok-handguard-carbine.mlok_bottom_slot0_x":1.83,"magpul-moe-mlok-handguard-carbine.mlok_bottom_slots":3,"magpul-moe-mlok-handguard-carbine.mlok_side_face_angle":78,"magpul-moe-mlok-handguard-carbine.mlok_side_face_distance":1.0462,"magpul-moe-mlok-handguard-carbine.mlok_side_slot0_x":1.83,"magpul-moe-mlok-handguard-carbine.mlok_side_slot_y":0.16,"magpul-moe-mlok-handguard-carbine.mlok_side_slots":3,"magpul-moe-mlok-handguard-carbine.mounting_length":6.6,"magpul-moe-mlok-handguard-carbine.panel_depth":0.02,"magpul-moe-mlok-handguard-carbine.panel_rib":0.12,"magpul-moe-mlok-handguard-carbine.rear_collar_gap":0.36,"magpul-moe-mlok-handguard-carbine.rear_collar_gap_y":-0.07,"magpul-moe-mlok-handguard-carbine.rear_collar_od":1.72,"magpul-moe-mlok-handguard-carbine.seam_groove":0.02,"magpul-moe-mlok-handguard-carbine.seam_y":-0.33,"magpul-moe-mlok-handguard-carbine.top_above_axis":1.18,"magpul-moe-mlok-handguard-carbine.top_half_width":0.5,"magpul-moe-mlok-handguard-carbine.vent0_x":2.03,"magpul-moe-mlok-handguard-carbine.vent_count":4,"magpul-moe-mlok-handguard-carbine.vent_length":0.55,"magpul-moe-mlok-handguard-carbine.vent_pitch":1.15,"magpul-moe-mlok-handguard-carbine.vent_width":0.16,"magpul-moe-mlok-handguard-carbine.visible_rear_x":0.12,"magpul-moe-mlok-handguard-carbine.wall":0.15,"magpul-moe-mlok-handguard-carbine.width":2.2,"magpul-moe-mlok-handguard-carbine.window0_x":1.42,"magpul-moe-mlok-handguard-carbine.window_count":4,"magpul-moe-mlok-handguard-carbine.window_depth":0.06,"magpul-moe-mlok-handguard-carbine.window_height":0.13,"magpul-moe-mlok-handguard-carbine.window_length":0.52,"magpul-moe-mlok-handguard-carbine.window_pitch":1.09,"magpul-moe-mlok-handguard-carbine.window_y":-0.96,"std.ar15.slip_ring_notch_width":0.203,"std.mlok.slot_corner_r":0.0937007874015748,"std.mlok.slot_length":1.2598425196850394,"std.mlok.slot_pitch":1.574803149606299,"std.mlok.slot_width":0.2755905511811024},"profiles":{"side":[[0,-0.995],[0.2,-1.424],[0.174,-1.457],[0.129,-1.427],[0.018,-1.435],[0.007,-1.453],[0.03,-1.668],[0.081,-1.89],[0.118,-1.971],[0.159,-2.019],[0.218,-2.026],[0.259,-2.06],[0.311,-2.252],[0.433,-2.359],[0.884,-2.374],[5.861,-2.374],[5.935,-2.396],[5.983,-2.437],[5.991,-2.526],[6.031,-2.603],[6.135,-2.618],[6.198,-2.577],[6.264,-2.393],[6.338,-2.267],[6.497,-2.13],[6.623,-2.093],[6.771,-2.093],[6.911,-2.056],[6.978,-2.026],[7.056,-1.934],[7.1,-1.808],[7.1,-1.106],[7.041,-0.965],[6.656,-0.484],[6.664,-0.47],[6.59,-0.396],[6.56,-0.337],[6.479,-0.263],[6.316,-0.063],[6.238,0],[5.876,0],[5.75,-0.037],[5.203,-0.037],[5.092,0],[4.73,0],[4.604,-0.037],[4.034,-0.037],[3.931,0],[3.576,0],[3.465,-0.037],[2.888,-0.037],[2.77,0],[2.422,0],[2.296,-0.037],[1.764,-0.037],[1.646,0],[0.743,0],[0.714,-0.015],[0.684,0],[0.618,0],[0.514,-0.03],[0.388,-0.104],[0.333,-0.166],[0.318,-0.255],[0.255,-0.348],[0.166,-0.355],[0.111,-0.381],[0.037,-0.64]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"y":"top_above_axis"}}},"bounds":{"min":[0,-1.438,-1.1005],"max":[7.1,1.1615,1.1005]},"volume_in3":7.3841,"centroid":[3.6047,-0.1616,0],"shell":[3.4639,-0.3006,0.0001],"area_in2":147.9245,"triangles":19800,"manifold":true,"slabs":[[0,-1.172,-1.041,0.394,1.08,1.041],[0.394,-1.218,-1.1,5.917,1.161,1.1],[5.917,-1.438,-1.1,6.311,1.161,1.1],[6.311,-1.133,-1.1,6.706,1.12,1.1],[6.706,-0.913,-1.1,7.1,0.634,1.1]],"slots":["body","heat_shield"]},"magpul-moe-mlok-handguard-mid":{"part":"magpul-moe-mlok-handguard-mid","model":"magpul-moe-mlok-handguard-mid.glb","script":"magpul_moe_mlok_handguard_mid.py","inputs":{"magpul-moe-mlok-handguard-mid.bottom_half_width":0.45,"magpul-moe-mlok-handguard-mid.face_flat":0.62,"magpul-moe-mlok-handguard-mid.front_flange_od":1.36,"magpul-moe-mlok-handguard-mid.front_wall_x":8.03,"magpul-moe-mlok-handguard-mid.heat_shield_thickness":0.03,"magpul-moe-mlok-handguard-mid.length":9.2,"magpul-moe-mlok-handguard-mid.mlok_bottom_face_distance":1.19,"magpul-moe-mlok-handguard-mid.mlok_bottom_slot0_x":3.91,"magpul-moe-mlok-handguard-mid.mlok_bottom_slots":3,"magpul-moe-mlok-handguard-mid.mlok_side_face_angle":78,"magpul-moe-mlok-handguard-mid.mlok_side_face_distance":1.0587,"magpul-moe-mlok-handguard-mid.mlok_side_slot0_x":3.91,"magpul-moe-mlok-handguard-mid.mlok_side_slot_y":0.22,"magpul-moe-mlok-handguard-mid.mlok_side_slots":3,"magpul-moe-mlok-handguard-mid.mounting_length":8.6,"magpul-moe-mlok-handguard-mid.panel_depth":0.02,"magpul-moe-mlok-handguard-mid.panel_rib":0.12,"magpul-moe-mlok-handguard-mid.rear_collar_od":1.72,"magpul-moe-mlok-handguard-mid.seam_groove":0.02,"magpul-moe-mlok-handguard-mid.seam_y":-0.245,"magpul-moe-mlok-handguard-mid.top_above_axis":1.15,"magpul-moe-mlok-handguard-mid.top_half_width":0.5,"magpul-moe-mlok-handguard-mid.vent0_x":2.25,"magpul-moe-mlok-handguard-mid.vent_count":6,"magpul-moe-mlok-handguard-mid.vent_length":0.65,"magpul-moe-mlok-handguard-mid.vent_pitch":1.14,"magpul-moe-mlok-handguard-mid.vent_width":0.16,"magpul-moe-mlok-handguard-mid.visible_rear_x":0.12,"magpul-moe-mlok-handguard-mid.wall":0.15,"magpul-moe-mlok-handguard-mid.width":2.2,"magpul-moe-mlok-handguard-mid.window0_x":1.38,"magpul-moe-mlok-handguard-mid.window_count":6,"magpul-moe-mlok-handguard-mid.window_depth":0.06,"magpul-moe-mlok-handguard-mid.window_height":0.13,"magpul-moe-mlok-handguard-mid.window_length":0.63,"magpul-moe-mlok-handguard-mid.window_pitch":1.1,"magpul-moe-mlok-handguard-mid.window_y":-0.85,"std.ar15.slip_ring_notch_width":0.203,"std.mlok.slot_corner_r":0.0937007874015748,"std.mlok.slot_length":1.2598425196850394,"std.mlok.slot_pitch":1.574803149606299,"std.mlok.slot_width":0.2755905511811024},"profiles":{"side":[[0,-0.622],[0,-0.72],[0.024,-0.744],[0.024,-1.184],[0.049,-1.208],[0.024,-1.574],[0.049,-1.599],[0.049,-1.77],[0.098,-1.818],[0.098,-2.038],[0.22,-2.16],[0.22,-2.209],[0.293,-2.282],[0.293,-2.307],[0.354,-2.343],[0.378,-2.343],[0.427,-2.294],[0.5,-2.368],[0.574,-2.294],[0.598,-2.319],[0.671,-2.319],[0.696,-2.343],[0.72,-2.319],[0.818,-2.319],[0.867,-2.27],[0.891,-2.294],[1.428,-2.294],[1.477,-2.343],[1.599,-2.343],[1.648,-2.294],[1.672,-2.319],[1.843,-2.319],[1.867,-2.343],[2.038,-2.343],[2.087,-2.294],[2.575,-2.294],[2.648,-2.368],[2.722,-2.368],[2.77,-2.319],[2.868,-2.343],[2.917,-2.294],[2.966,-2.319],[2.99,-2.294],[3.039,-2.343],[3.21,-2.343],[3.259,-2.294],[3.771,-2.294],[3.82,-2.343],[3.893,-2.343],[3.918,-2.319],[3.991,-2.319],[4.04,-2.27],[4.064,-2.294],[4.357,-2.294],[4.406,-2.343],[4.577,-2.343],[4.625,-2.294],[4.747,-2.294],[4.796,-2.343],[4.894,-2.343],[4.918,-2.319],[4.967,-2.319],[4.992,-2.343],[5.358,-2.343],[5.431,-2.294],[5.724,-2.294],[5.773,-2.343],[5.943,-2.343],[6.041,-2.294],[6.066,-2.319],[6.139,-2.319],[6.188,-2.27],[6.212,-2.27],[6.261,-2.319],[6.31,-2.294],[6.334,-2.319],[6.407,-2.319],[6.432,-2.343],[6.529,-2.343],[6.578,-2.294],[6.92,-2.294],[6.944,-2.319],[6.993,-2.294],[7.042,-2.319],[7.091,-2.27],[7.14,-2.319],[7.31,-2.319],[7.335,-2.294],[7.53,-2.294],[7.554,-2.319],[7.701,-2.319],[7.725,-2.343],[7.896,-2.343],[8.03,-2.477],[8.067,-2.563],[8.165,-2.563],[8.177,-2.453],[8.201,-2.429],[8.226,-2.307],[8.275,-2.209],[8.458,-2.026],[8.482,-2.05],[8.506,-2.026],[8.604,-2.026],[8.702,-1.977],[8.799,-1.977],[8.848,-1.953],[9.031,-1.77],[9.031,-1.623],[9.08,-1.574],[9.08,-0.867],[8.934,-0.72],[8.958,-0.696],[8.812,-0.549],[8.812,-0.525],[8.567,-0.256],[8.567,-0.232],[8.555,-0.22],[8.506,-0.244],[8.482,-0.22],[8.433,-0.22],[8.299,-0.085],[8.287,-0.024],[8.213,-0.024],[8.189,0],[7.921,0],[7.896,-0.024],[7.091,-0.024],[7.066,0],[6.725,0],[6.7,-0.024],[0.403,-0.024],[0.098,-0.33],[0.098,-0.354],[0.024,-0.427],[0.024,-0.598]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"x":"visible_rear_x","y":"top_above_axis"}}},"bounds":{"min":[0,-1.413,-1.1005],"max":[9.2,1.138,1.1005]},"volume_in3":9.4561,"centroid":[4.615,-0.134,0],"shell":[4.4757,-0.2747,0],"area_in2":191.8555,"triangles":24066,"manifold":true,"slabs":[[0,-1.149,-1.03,0.4,1.01,1.03],[0.4,-1.169,-1.1,8,1.138,1.1],[8,-1.413,-1.1,8.4,1.138,1.1],[8.4,-1.054,-1.1,8.8,1.138,1.1],[8.8,-0.838,-1.1,9.2,0.77,1.1]],"slots":["body","heat_shield"]},"magpul-moe-plus":{"part":"magpul-moe-plus","model":"magpul-moe-plus.glb","script":"magpul_moe_plus.py","inputs":{"magpul-moe-plus.back_strap_face_width":0.2,"magpul-moe-plus.front_strap_face_width":0.72,"magpul-moe-plus.grip_angle":26.282,"magpul-moe-plus.lug_slot_width":0.425,"magpul-moe-plus.seat_x":-0.255,"magpul-moe-plus.thickness":1.2,"magpul-moe-plus.toe_y":-4,"std.ar15.deck_y":0.2485,"std.ar15.grip_lug_depth":0.93,"std.ar15.grip_lug_face_angle":60,"std.ar15.grip_lug_face_from_pin":1.228,"std.ar15.grip_lug_front_from_rear_face":2.3,"std.ar15.grip_lug_length":1.25,"std.ar15.grip_lug_width":0.375,"std.ar15.grip_seat_below_deck":1.318,"std.ar15.rear_underside_arc_center_below_seat":0.1928,"std.ar15.rear_underside_arc_center_x":-1.0238,"std.ar15.rear_underside_arc_r_fullest":0.716,"std.ar15.rear_underside_round_r":0.44,"std.ar15.receiver_rear_x":-1.125},"profiles":{"side":[[-1.785,-3.074],[-1.766,-3.143],[-1.694,-3.213],[-1.59,-3.281],[-1.31,-3.427],[-1.141,-3.51],[-1.122,-3.51],[-1.099,-3.49],[-1.067,-3.511],[-1.061,-3.536],[-0.715,-3.701],[-0.508,-3.787],[-0.482,-3.775],[-0.472,-3.785],[-0.472,-3.804],[-0.455,-3.817],[0.036,-4],[0.071,-4],[0.135,-3.969],[0.171,-3.924],[0.209,-3.851],[0.208,-3.767],[0.146,-3.649],[0.137,-3.565],[0.145,-3.523],[1.116,-1.44],[1.161,-1.378],[1.239,-1.314],[1.319,-1.283],[1.411,-1.278],[1.428,-1.265],[1.445,-1.043],[1.457,-0.321],[1.453,-0.214],[1.414,-0.119],[1.35,-0.048],[1.285,-0.011],[1.246,0],[0.176,-0.005],[0.167,0.004],[0.147,0.119],[0.119,0.187],[0.042,0.305],[-0.091,0.447],[-0.203,0.53],[-0.341,0.601],[-0.487,0.646],[-0.605,0.664],[-0.728,0.663],[-0.766,0.647],[-0.798,0.618],[-0.824,0.561],[-0.831,0.519],[-0.83,0.354],[-0.793,0.295],[-0.495,0.063],[-0.425,-0.009],[-0.356,-0.111],[-0.305,-0.233],[-0.281,-0.359],[-0.28,-0.47],[-0.309,-0.604],[-0.347,-0.696],[-0.509,-0.931],[-0.501,-0.965],[-0.55,-0.992],[-0.546,-1.038],[-0.556,-1.048],[-0.592,-1.054],[-0.603,-1.077],[-0.595,-1.107],[-0.641,-1.127],[-0.648,-1.153],[-0.641,-1.172],[-0.69,-1.2],[-0.686,-1.242],[-0.731,-1.265],[-0.739,-1.288],[-0.731,-1.307],[-0.773,-1.327],[-0.784,-1.353],[-0.776,-1.376],[-0.818,-1.396],[-0.829,-1.419],[-0.822,-1.445],[-0.86,-1.465],[-0.871,-1.484],[-0.867,-1.515],[-0.905,-1.534],[-0.916,-1.565],[-0.912,-1.584],[-0.95,-1.603],[-0.957,-1.649],[-0.999,-1.684],[-0.999,-1.718],[-1.033,-1.738],[-1.044,-1.757],[-1.044,-1.791],[-1.069,-1.801],[-1.086,-1.822],[-1.085,-1.86],[-1.12,-1.876],[-1.131,-1.899],[-1.131,-1.926],[-1.172,-1.964],[-1.172,-1.999],[-1.206,-2.022],[-1.217,-2.068],[-1.251,-2.099],[-1.259,-2.141],[-1.289,-2.164],[-1.3,-2.21],[-1.334,-2.241],[-1.341,-2.283],[-1.372,-2.306],[-1.379,-2.352],[-1.409,-2.375],[-1.42,-2.425],[-1.451,-2.448],[-1.462,-2.498],[-1.492,-2.521],[-1.503,-2.571],[-1.533,-2.598],[-1.541,-2.64],[-1.567,-2.66],[-1.582,-2.713],[-1.609,-2.736],[-1.62,-2.782],[-1.646,-2.806],[-1.657,-2.855],[-1.699,-2.89],[-1.744,-2.967],[-1.774,-3.028]],"front":[[-0.601,2.919],[-0.601,0.548],[-0.557,0.436],[-0.548,0.275],[-0.346,0.019],[-0.297,0.005],[0,0],[0.088,0],[0.341,0.015],[0.514,0.222],[0.557,0.295],[0.557,0.421],[0.601,0.557],[0.601,2.919],[0.562,3.138],[0.48,3.367],[0.441,3.552],[0.431,4.652],[0.355,4.664],[0.263,4.576],[0.185,4.533],[0.083,4.498],[-0.015,4.489],[-0.175,4.528],[-0.278,4.591],[-0.346,4.659],[-0.404,4.664],[-0.436,4.627],[-0.441,3.532],[-0.475,3.367],[-0.528,3.24],[-0.587,3.035]]},"features":{"side":{},"front":{}},"placement":{"side":{"plane":"xy","offset":{}},"front":{"plane":"zy","offset":{"y":"toe_y"}}},"bounds":{"min":[-1.785,-4,-0.6],"max":[1.457,0.6639,0.6]},"volume_in3":7.6847,"centroid":[-0.1123,-1.9422,0],"shell":[-0.1301,-1.8861,0],"area_in2":34.4051,"triangles":17528,"manifold":true,"receiver":{"slot":{"width":0.425,"clear_of_lug":0.025,"rear_x":0.155,"floor_at_rear_y":-0.3196,"foot_x":1.2555,"bottom_y":-0.955},"scoop":{"axis_x":-0.7688,"axis_y":-0.1928,"on_centre_plane_r":0.691,"across_r":0.465}},"slabs":[[-0.903,-4,-0.553,0.209,-3.611,0.556],[-1.679,-3.611,-0.6,0.285,-3.223,0.6],[-1.785,-3.223,-0.6,0.466,-2.834,0.6],[-1.652,-2.834,-0.6,0.647,-2.445,0.6],[-1.447,-2.445,-0.6,0.829,-2.057,0.6],[-1.214,-2.057,-0.6,1.01,-1.668,0.6],[-0.98,-1.668,-0.6,1.385,-1.279,0.6],[-0.736,-1.279,-0.6,1.448,-0.891,0.6],[-0.481,-0.891,-0.565,1.454,-0.502,0.566],[-0.355,-0.502,-0.447,1.457,-0.113,0.452],[-0.768,-0.113,-0.439,1.409,0.275,0.437],[-0.831,0.275,-0.437,0.061,0.664,0.434]],"slots":["body","base"]},"magpul-moe-sl-carbine":{"part":"magpul-moe-sl-carbine","model":"magpul-moe-sl-carbine.glb","script":"magpul_moe_sl_carbine.py","inputs":{"bcm-receiver-extension.tube_front_behind_pin":0.669,"bcm-receiver-extension.tube_length":7.25,"magpul-moe-sl-carbine.bore_diameter":1.163,"magpul-moe-sl-carbine.butt_behind_pin_pos1":9.255,"magpul-moe-sl-carbine.grip_edge_height":0.037,"magpul-moe-sl-carbine.grip_first_tooth":0.045,"magpul-moe-sl-carbine.grip_foot_half_width":0.415,"magpul-moe-sl-carbine.grip_teeth":12,"magpul-moe-sl-carbine.grip_tooth_height":0.023,"magpul-moe-sl-carbine.grip_tooth_pitch":0.082,"magpul-moe-sl-carbine.latch_arm_half_width":0.477,"magpul-moe-sl-carbine.latch_boss_half_width":0.512,"magpul-moe-sl-carbine.latch_tab_half_width":0.655,"magpul-moe-sl-carbine.lock_pin_face_half_width":0.59,"magpul-moe-sl-carbine.lock_slot_floor_half_width":0.403,"magpul-moe-sl-carbine.panel_recess_depth":0.05,"magpul-moe-sl-carbine.rail_channel_floor_below_axis":0.874,"magpul-moe-sl-carbine.rail_channel_width":0.49,"magpul-moe-sl-carbine.tube_axis_below_top":0.667},"profiles":{"side":[[0,-0.69],[0.049,-0.76],[0.046,-0.803],[0.012,-0.852],[0.012,-0.904],[0.064,-0.977],[0.058,-1.023],[0.024,-1.065],[0.024,-1.117],[0.079,-1.175],[0.04,-1.3],[0.094,-1.382],[0.091,-1.431],[0.058,-1.477],[0.055,-1.522],[0.11,-1.589],[0.104,-1.641],[0.07,-1.681],[0.07,-1.727],[0.122,-1.784],[0.128,-1.827],[0.085,-1.885],[0.088,-1.946],[0.137,-1.992],[0.131,-2.053],[0.098,-2.105],[0.101,-2.141],[0.155,-2.205],[0.155,-2.242],[0.113,-2.306],[0.113,-2.342],[0.171,-2.418],[0.165,-2.464],[0.128,-2.516],[0.131,-2.562],[0.186,-2.629],[0.183,-2.665],[0.143,-2.726],[0.143,-2.763],[0.198,-2.836],[0.195,-2.879],[0.155,-2.937],[0.158,-2.982],[0.213,-3.052],[0.207,-3.092],[0.171,-3.141],[0.171,-3.18],[0.229,-3.254],[0.222,-3.302],[0.186,-3.351],[0.186,-3.403],[0.238,-3.464],[0.232,-3.519],[0.192,-3.567],[0.204,-3.625],[0.253,-3.683],[0.25,-3.72],[0.21,-3.778],[0.21,-3.82],[0.268,-3.9],[0.259,-3.948],[0.222,-3.985],[0.222,-4.015],[0.232,-4.052],[0.28,-4.116],[0.265,-4.168],[0.238,-4.198],[0.241,-4.25],[0.296,-4.326],[0.29,-4.372],[0.259,-4.409],[0.268,-4.482],[0.475,-5.04],[0.536,-5.158],[0.629,-5.227],[0.989,-5.261],[1.026,-5.245],[1.309,-5.236],[1.382,-5.203],[1.439,-5.149],[2.774,-3.077],[2.85,-2.97],[2.927,-2.902],[3.055,-2.859],[4.844,-2.612],[5.14,-2.609],[5.213,-2.563],[6.649,-2.371],[6.746,-2.347],[6.829,-2.301],[6.906,-2.233],[6.983,-2.135],[7.287,-1.586],[7.327,-1.355],[7.354,-0.687],[7.3,-0.178],[7.272,-0.084],[7.204,-0.021],[0.995,-0.034],[0.684,-0.03],[0.623,-0.003],[0.468,0],[0.169,-0.03],[0.085,-0.102],[0.049,-0.163],[0.061,-0.227],[0.018,-0.297],[0.049,-0.404],[0.012,-0.459],[0.006,-0.498],[0.049,-0.587],[0.006,-0.651]],"front":[[-0.85,-1.1],[-0.84,-1.328],[-0.785,-1.448],[-0.778,-1.51],[-0.691,-4.139],[-0.661,-4.399],[-0.457,-5.124],[-0.431,-5.176],[-0.371,-5.239],[-0.306,-5.275],[0.013,-5.301],[0.296,-5.278],[0.361,-5.246],[0.434,-5.169],[0.473,-5.075],[0.665,-4.386],[0.694,-4.103],[0.782,-1.471],[0.843,-1.318],[0.85,-1.051],[0.811,-0.931],[0.782,-0.759],[0.678,-0.473],[0.629,-0.366],[0.554,-0.258],[0.426,-0.137],[0.296,-0.062],[0.14,-0.013],[-0.002,-0.002],[-0.007,0],[-0.163,-0.02],[-0.312,-0.072],[-0.445,-0.153],[-0.57,-0.281],[-0.665,-0.444],[-0.782,-0.765],[-0.801,-0.912],[-0.843,-1.016]],"web":[[-0.457,-2.206],[-0.408,-2.392],[-0.388,-2.583],[-0.375,-3.022],[-0.349,-3.376],[-0.343,-3.623],[-0.31,-4.166],[-0.304,-4.423],[-0.278,-4.777],[-0.278,-5.401],[0.279,-5.402],[0.281,-4.767],[0.317,-4.163],[0.343,-3.578],[0.359,-3.363],[0.372,-3.035],[0.388,-2.824],[0.388,-2.583],[0.408,-2.395],[0.46,-2.203],[0.46,-1.199],[-0.455,-1.197]]},"features":{"side":{"through":[[[1.103,-1.812],[1.119,-1.763],[1.181,-1.731],[2.293,-1.728],[2.329,-1.754],[2.325,-1.824],[2.29,-1.865],[2.236,-1.877],[1.151,-1.877],[1.112,-1.855]],[[1.335,-2.421],[1.344,-2.339],[1.387,-2.254],[1.434,-2.21],[1.495,-2.188],[1.577,-2.191],[1.62,-2.207],[1.655,-2.245],[1.67,-2.29],[1.667,-2.367],[1.602,-2.478],[1.492,-2.533],[1.422,-2.524],[1.356,-2.476]],[[1.161,-4.732],[1.173,-4.695],[1.777,-3.759],[1.824,-3.724],[1.891,-3.731],[1.929,-3.787],[1.917,-3.86],[1.317,-4.802],[1.248,-4.84],[1.199,-4.828],[1.17,-4.799]]],"buttpad":[[[-0.139,0.142],[0.334,0.142],[0.73,-5.405],[-0.139,-5.405]]],"latch":[[[2.415,-1.986],[3.458,-1.809],[4.189,-1.449],[4.372,-1.397],[4.372,-1.855],[4.189,-1.885],[3.519,-2.022],[2.458,-2.229]]],"latch_boss":[[[4.592,-1.602],[4.584,-1.658],[4.562,-1.711],[4.527,-1.757],[4.482,-1.792],[4.429,-1.813],[4.372,-1.821],[4.315,-1.813],[4.262,-1.792],[4.217,-1.757],[4.182,-1.711],[4.16,-1.658],[4.153,-1.602],[4.16,-1.545],[4.182,-1.492],[4.217,-1.446],[4.262,-1.411],[4.315,-1.39],[4.372,-1.382],[4.429,-1.39],[4.482,-1.411],[4.527,-1.446],[4.562,-1.492],[4.584,-1.545]]],"pocket":[[[0.806,-1.245],[2.94,-1.306],[5.987,-1.382],[6.902,-1.413],[6.963,-1.717],[6.597,-2.327],[6.597,-5.68],[1.172,-5.68],[1.141,-5.07],[1.05,-4.156],[0.806,-1.717]]],"grip":[[[2.428,-1.961],[3.464,-1.784],[3.5,-2.041],[2.44,-2.223]]],"lever":[[[2.863,-1.535],[3.808,-1.385],[4.235,-1.379],[4.372,-1.379],[4.372,-1.827],[4.281,-1.83],[3.915,-1.861],[3.503,-1.943],[3.397,-1.9],[3.244,-1.839],[3.092,-1.717]],[[4.372,-1.379],[4.844,-1.367],[4.844,-1.486],[4.372,-1.504]]],"lock_slot":[[[4.985,-1.461],[5.009,-1.437],[5.195,-1.437],[5.219,-1.461],[5.219,-1.945],[5.21,-1.99],[5.184,-2.028],[5.147,-2.053],[5.102,-2.062],[5.058,-2.053],[5.02,-2.028],[4.994,-1.99],[4.985,-1.945]]],"lock_pin":[[[5.23,-1.548],[5.225,-1.577],[5.212,-1.603],[5.192,-1.624],[5.166,-1.637],[5.137,-1.641],[5.108,-1.637],[5.083,-1.624],[5.062,-1.603],[5.049,-1.577],[5.044,-1.548],[5.049,-1.52],[5.062,-1.494],[5.083,-1.473],[5.108,-1.46],[5.137,-1.455],[5.166,-1.46],[5.192,-1.473],[5.212,-1.494],[5.225,-1.52]]],"qd":[[[1.675,-2.335],[1.671,-2.372],[1.66,-2.409],[1.642,-2.442],[1.618,-2.471],[1.589,-2.496],[1.555,-2.514],[1.519,-2.525],[1.481,-2.528],[1.443,-2.525],[1.407,-2.514],[1.374,-2.496],[1.344,-2.471],[1.32,-2.442],[1.302,-2.409],[1.291,-2.372],[1.288,-2.335],[1.291,-2.297],[1.302,-2.261],[1.32,-2.227],[1.344,-2.198],[1.374,-2.174],[1.407,-2.156],[1.443,-2.145],[1.481,-2.141],[1.519,-2.145],[1.555,-2.156],[1.589,-2.174],[1.618,-2.198],[1.642,-2.227],[1.66,-2.261],[1.671,-2.297]],[[1.695,-2.335],[1.691,-2.376],[1.678,-2.416],[1.659,-2.453],[1.632,-2.485],[1.6,-2.512],[1.563,-2.532],[1.523,-2.544],[1.481,-2.548],[1.439,-2.544],[1.4,-2.532],[1.363,-2.512],[1.33,-2.485],[1.304,-2.453],[1.284,-2.416],[1.272,-2.376],[1.268,-2.335],[1.272,-2.293],[1.284,-2.253],[1.304,-2.216],[1.33,-2.184],[1.363,-2.157],[1.4,-2.137],[1.439,-2.125],[1.481,-2.121],[1.523,-2.125],[1.563,-2.137],[1.6,-2.157],[1.632,-2.184],[1.659,-2.216],[1.678,-2.253],[1.691,-2.293]],[[1.792,-2.335],[1.786,-2.395],[1.768,-2.453],[1.74,-2.507],[1.701,-2.554],[1.654,-2.593],[1.6,-2.622],[1.542,-2.639],[1.481,-2.646],[1.421,-2.639],[1.362,-2.622],[1.308,-2.593],[1.261,-2.554],[1.223,-2.507],[1.194,-2.453],[1.176,-2.395],[1.17,-2.335],[1.176,-2.274],[1.194,-2.216],[1.223,-2.162],[1.261,-2.115],[1.308,-2.076],[1.362,-2.048],[1.421,-2.03],[1.481,-2.024],[1.542,-2.03],[1.6,-2.048],[1.654,-2.076],[1.701,-2.115],[1.74,-2.162],[1.768,-2.216],[1.786,-2.274]],[[1.841,-2.335],[1.834,-2.405],[1.813,-2.472],[1.78,-2.535],[1.735,-2.589],[1.681,-2.634],[1.619,-2.667],[1.551,-2.687],[1.481,-2.694],[1.411,-2.687],[1.343,-2.667],[1.281,-2.634],[1.227,-2.589],[1.182,-2.535],[1.149,-2.472],[1.129,-2.405],[1.122,-2.335],[1.129,-2.265],[1.149,-2.197],[1.182,-2.135],[1.227,-2.08],[1.281,-2.036],[1.343,-2.002],[1.411,-1.982],[1.481,-1.975],[1.551,-1.982],[1.619,-2.002],[1.681,-2.036],[1.735,-2.08],[1.78,-2.135],[1.813,-2.197],[1.834,-2.265]]],"panel":[[[1.065,-1.169],[4.844,-1.169],[4.844,-2.318],[3.702,-2.498],[2.94,-2.613],[2.818,-2.61],[2.635,-2.546],[2.33,-2.434],[1.83,-2.245],[1.776,-2.128],[1.688,-2.04],[1.574,-1.987],[1.481,-1.975],[1.388,-1.987],[1.301,-2.023],[1.226,-2.082],[1.065,-2.034]],[[5.405,-1.169],[7.152,-1.169],[6.627,-2.071],[5.405,-2.248]],[[0.837,-2.175],[1.133,-2.247],[1.127,-2.397],[1.17,-2.514],[1.25,-2.61],[1.358,-2.673],[1.481,-2.694],[1.604,-2.673],[1.712,-2.61],[1.802,-2.498],[1.964,-2.54],[2.421,-2.647],[2.574,-2.708],[2.62,-2.784],[2.33,-3.287],[2.086,-3.683],[1.888,-3.805],[1.233,-4.765],[1.248,-4.933],[1.157,-4.887],[1.087,-4.765],[1.01,-4.339],[0.913,-2.967]]],"tab":[[[0.867,-3.851],[1.279,-3.851],[1.279,-4.049],[0.867,-4.049]]]},"front":{},"web":{}},"placement":{"side":{"plane":"xy","offset":{"y":"tube_axis_below_top"}},"front":{"plane":"zy","offset":{"y":"tube_axis_below_top"}},"web":{"plane":"zy","offset":{"y":"tube_axis_below_top"}}},"bounds":{"min":[0.0002,-4.594,-0.85],"max":[7.354,0.667,0.85]},"volume_in3":18.5173,"centroid":[2.722,-1.3129,0.0016],"shell":[2.9279,-1.0947,0.0006],"area_in2":129.4174,"triangles":8972,"manifold":true,"slabs":[[0,-4.136,-0.85,0.387,0.659,0.85],[0.387,-4.594,-0.85,1.548,0.667,0.85],[1.548,-4.312,-0.85,1.935,0.635,0.85],[1.935,-3.712,-0.85,2.322,0.636,0.85],[2.322,-3.111,-0.85,2.709,0.637,0.85],[2.709,-2.51,-0.85,3.097,0.637,0.85],[3.097,-2.186,-0.85,3.484,0.638,0.85],[3.484,-2.133,-0.85,3.871,0.639,0.85],[3.871,-2.079,-0.85,4.258,0.64,0.85],[4.258,-2.026,-0.85,4.645,0.641,0.85],[4.645,-1.973,-0.85,5.419,0.642,0.85],[5.419,-1.868,-0.85,5.806,0.643,0.85],[5.806,-1.817,-0.85,6.193,0.644,0.85],[6.193,-1.765,-0.85,6.58,0.645,0.85],[6.58,-1.713,-0.85,6.967,0.646,0.85],[6.967,-1.488,-0.85,7.354,0.646,0.85]],"slots":["body","buttpad"]},"magpul-moe-sl-handguard-carbine":{"part":"magpul-moe-sl-handguard-carbine","model":"magpul-moe-sl-handguard-carbine.glb","script":"magpul_moe_sl_handguard_carbine.py","inputs":{"magpul-moe-sl-handguard-carbine.bottom_below_axis":1.16,"magpul-moe-sl-handguard-carbine.bottom_half_width":0.42,"magpul-moe-sl-handguard-carbine.bottom_notch0_x":0.27,"magpul-moe-sl-handguard-carbine.bottom_notch_length":0.36,"magpul-moe-sl-handguard-carbine.bottom_notch_pitch":0.78,"magpul-moe-sl-handguard-carbine.bottom_notch_width":0.1,"magpul-moe-sl-handguard-carbine.bottom_notches":10,"magpul-moe-sl-handguard-carbine.crown_groove_depth":0.015,"magpul-moe-sl-handguard-carbine.crown_groove_end_x":6.85,"magpul-moe-sl-handguard-carbine.crown_groove_span":0.38,"magpul-moe-sl-handguard-carbine.crown_grooves":8,"magpul-moe-sl-handguard-carbine.face_flat":0.5,"magpul-moe-sl-handguard-carbine.front_flange_od":1.36,"magpul-moe-sl-handguard-carbine.front_flare_x":6.19,"magpul-moe-sl-handguard-carbine.front_room_d":1.7329,"magpul-moe-sl-handguard-carbine.front_wall_x":6.03,"magpul-moe-sl-handguard-carbine.front_width":1.99,"magpul-moe-sl-handguard-carbine.heat_shield_thickness":0.03,"magpul-moe-sl-handguard-carbine.length":8.9,"magpul-moe-sl-handguard-carbine.lower_round_y":-0.78,"magpul-moe-sl-handguard-carbine.mlok_axis_y":0.1635481,"magpul-moe-sl-handguard-carbine.mlok_bottom_face_distance":1.16,"magpul-moe-sl-handguard-carbine.mlok_bottom_slot0_x":1.81,"magpul-moe-sl-handguard-carbine.mlok_bottom_slots":4,"magpul-moe-sl-handguard-carbine.mlok_side_face_angle":70,"magpul-moe-sl-handguard-carbine.mlok_side_face_distance":0.8667674,"magpul-moe-sl-handguard-carbine.mlok_side_slot0_x":1.8,"magpul-moe-sl-handguard-carbine.mlok_side_slot_y":0.46,"magpul-moe-sl-handguard-carbine.mlok_side_slots":3,"magpul-moe-sl-handguard-carbine.mounting_length":6.6,"magpul-moe-sl-handguard-carbine.nose_corner_x":0.12,"magpul-moe-sl-handguard-carbine.nose_corner_y":0.24,"magpul-moe-sl-handguard-carbine.notch_depth":0.06,"magpul-moe-sl-handguard-carbine.outline_rear_x":-0.56,"magpul-moe-sl-handguard-carbine.rear_collar_od":1.72,"magpul-moe-sl-handguard-carbine.rib0_x":0.91,"magpul-moe-sl-handguard-carbine.rib_count":8,"magpul-moe-sl-handguard-carbine.rib_height":0.03,"magpul-moe-sl-handguard-carbine.rib_pitch":0.75,"magpul-moe-sl-handguard-carbine.rib_width":0.06,"magpul-moe-sl-handguard-carbine.ring_clearance":0.02,"magpul-moe-sl-handguard-carbine.rivet0_x":1,"magpul-moe-sl-handguard-carbine.rivet1_x":5.7,"magpul-moe-sl-handguard-carbine.rivet_d":0.13,"magpul-moe-sl-handguard-carbine.rivet_height":0.02,"magpul-moe-sl-handguard-carbine.seam_groove":0.02,"magpul-moe-sl-handguard-carbine.seam_y":-0.09,"magpul-moe-sl-handguard-carbine.top_above_axis":1.16,"magpul-moe-sl-handguard-carbine.top_half_width":0.6,"magpul-moe-sl-handguard-carbine.top_slot0_x":0.29,"magpul-moe-sl-handguard-carbine.top_slot_length":0.37,"magpul-moe-sl-handguard-carbine.top_slot_pitch":0.79,"magpul-moe-sl-handguard-carbine.top_slot_width":0.12,"magpul-moe-sl-handguard-carbine.top_slot_z":0.45,"magpul-moe-sl-handguard-carbine.top_slots":8,"magpul-moe-sl-handguard-carbine.wall":0.15,"magpul-moe-sl-handguard-carbine.width":1.8,"magpul-moe-sl-handguard-carbine.window_length":0.68,"std.ar15.slip_ring_notch_width":0.203,"std.ar15.slip_ring_od":2.1,"std.mlok.slot_corner_r":0.0937007874015748,"std.mlok.slot_length":1.2598425196850394,"std.mlok.slot_pitch":1.574803149606299,"std.mlok.slot_width":0.2755905511811024},"profiles":{"side":[[0,-0.483],[0,-0.542],[0.073,-0.556],[0.22,-0.41],[0.278,-0.41],[0.381,-0.512],[0.351,-0.542],[0.366,-0.586],[0.454,-0.586],[0.483,-0.556],[0.586,-0.659],[0.586,-0.893],[0.629,-0.878],[0.732,-0.981],[0.586,-1.156],[0.644,-1.215],[0.586,-1.274],[0.586,-1.361],[0.425,-1.552],[0.293,-1.42],[0.293,-1.303],[0.263,-1.303],[0.263,-1.742],[0.351,-1.83],[0.351,-1.918],[0.22,-2.049],[0.117,-1.947],[0.117,-1.771],[0.059,-1.713],[0.059,-1.537],[0,-1.508],[0,-1.683],[0.029,-1.742],[0,-1.8],[0.029,-1.859],[0,-1.888],[0,-1.976],[0.088,-2.064],[0.088,-2.21],[0.132,-2.313],[0.659,-2.313],[0.834,-2.371],[8.241,-2.371],[8.446,-2.547],[8.68,-2.547],[8.754,-2.503],[8.812,-2.093],[8.9,-2.005],[8.9,-1.654],[8.871,-1.596],[8.9,-1.566],[8.9,-1.332],[8.871,-1.303],[8.9,-1.274],[8.9,-1.186],[8.841,-1.098],[8.9,-1.01],[8.754,-0.893],[8.724,-0.395],[8.637,-0.307],[8.622,-0.234],[8.578,-0.278],[8.578,-0.366],[8.475,-0.468],[7.451,-0.468],[7.319,-0.337],[7.378,-0.22],[7.363,-0.176],[7.275,-0.263],[7.173,-0.161],[7.231,-0.102],[7.217,-0.088],[7.158,-0.117],[7.041,0],[6.953,0],[6.895,-0.059],[0.132,-0.059],[0.117,-0.337],[0.146,-0.366]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"x":"outline_rear_x","y":"top_above_axis"}}},"bounds":{"min":[-0.56,-1.3366,-0.9955],"max":[8.3313,1.2192,0.9955]},"volume_in3":7.8908,"centroid":[3.8185,-0.1825,0],"shell":[3.7282,-0.228,0],"area_in2":159.5657,"triangles":32642,"manifold":true,"slabs":[[-0.56,-1.18,-0.9,6.012,1.161,0.9],[6.012,-1.16,-0.996,6.785,1.219,0.996],[6.785,-1.16,-0.996,7.558,0.553,0.996],[7.558,-1.337,-0.996,8.331,0.553,0.996]],"slots":["body","heat_shield"]},"magpul-moe-sl-handguard-mid":{"part":"magpul-moe-sl-handguard-mid","model":"magpul-moe-sl-handguard-mid.glb","script":"magpul_moe_sl_handguard_mid.py","inputs":{"magpul-moe-sl-handguard-mid.bottom_below_axis":1.18,"magpul-moe-sl-handguard-mid.bottom_half_width":0.42,"magpul-moe-sl-handguard-mid.bottom_notch0_x":0.51,"magpul-moe-sl-handguard-mid.bottom_notch_length":0.47,"magpul-moe-sl-handguard-mid.bottom_notch_pitch":0.788,"magpul-moe-sl-handguard-mid.bottom_notch_width":0.1,"magpul-moe-sl-handguard-mid.bottom_notches":13,"magpul-moe-sl-handguard-mid.crown_groove_depth":0.015,"magpul-moe-sl-handguard-mid.crown_groove_end_x":8.32,"magpul-moe-sl-handguard-mid.crown_groove_span":0.4,"magpul-moe-sl-handguard-mid.crown_grooves":8,"magpul-moe-sl-handguard-mid.face_flat":0.5,"magpul-moe-sl-handguard-mid.front_flange_od":1.36,"magpul-moe-sl-handguard-mid.front_flare_x":7.99,"magpul-moe-sl-handguard-mid.front_room_d":1.7329,"magpul-moe-sl-handguard-mid.front_wall_x":8.03,"magpul-moe-sl-handguard-mid.front_width":1.97,"magpul-moe-sl-handguard-mid.heat_shield_thickness":0.03,"magpul-moe-sl-handguard-mid.length":10.9,"magpul-moe-sl-handguard-mid.lower_round_y":-0.8,"magpul-moe-sl-handguard-mid.mlok_axis_y":0.2206843,"magpul-moe-sl-handguard-mid.mlok_bottom_face_distance":1.18,"magpul-moe-sl-handguard-mid.mlok_bottom_slot0_x":2.15,"magpul-moe-sl-handguard-mid.mlok_bottom_slots":4,"magpul-moe-sl-handguard-mid.mlok_side_face_angle":76,"magpul-moe-sl-handguard-mid.mlok_side_face_distance":0.8652203,"magpul-moe-sl-handguard-mid.mlok_side_slot0_x":2.15,"magpul-moe-sl-handguard-mid.mlok_side_slot_y":0.43,"magpul-moe-sl-handguard-mid.mlok_side_slots":4,"magpul-moe-sl-handguard-mid.mounting_length":8.6,"magpul-moe-sl-handguard-mid.nose_corner_x":0.15,"magpul-moe-sl-handguard-mid.nose_corner_y":0.23,"magpul-moe-sl-handguard-mid.notch_depth":0.06,"magpul-moe-sl-handguard-mid.outline_rear_x":-0.56,"magpul-moe-sl-handguard-mid.rear_collar_od":1.72,"magpul-moe-sl-handguard-mid.rib0_x":0.9,"magpul-moe-sl-handguard-mid.rib_count":9,"magpul-moe-sl-handguard-mid.rib_height":0.03,"magpul-moe-sl-handguard-mid.rib_pitch":0.788,"magpul-moe-sl-handguard-mid.rib_width":0.06,"magpul-moe-sl-handguard-mid.ring_clearance":0.02,"magpul-moe-sl-handguard-mid.seam_groove":0.02,"magpul-moe-sl-handguard-mid.seam_y":-0.1,"magpul-moe-sl-handguard-mid.top_above_axis":1.14,"magpul-moe-sl-handguard-mid.top_half_width":0.6,"magpul-moe-sl-handguard-mid.top_slot0_x":0.52,"magpul-moe-sl-handguard-mid.top_slot_length":0.36,"magpul-moe-sl-handguard-mid.top_slot_pitch":0.8,"magpul-moe-sl-handguard-mid.top_slot_width":0.115,"magpul-moe-sl-handguard-mid.top_slot_z":0.46,"magpul-moe-sl-handguard-mid.top_slots":10,"magpul-moe-sl-handguard-mid.wall":0.15,"magpul-moe-sl-handguard-mid.width":1.8,"magpul-moe-sl-handguard-mid.window_length":0.68,"std.ar15.slip_ring_notch_width":0.203,"std.ar15.slip_ring_od":2.1,"std.mlok.slot_corner_r":0.0937007874015748,"std.mlok.slot_length":1.2598425196850394,"std.mlok.slot_pitch":1.574803149606299,"std.mlok.slot_width":0.2755905511811024},"profiles":{"side":[[0,-0.203],[0,-0.329],[0.028,-0.357],[0.014,-0.399],[0.028,-0.413],[0.091,-0.42],[0.175,-0.504],[0.259,-0.532],[0.287,-0.518],[0.301,-0.532],[0.539,-0.532],[0.616,-0.609],[0.616,-0.792],[0.658,-0.834],[0.616,-0.876],[0.616,-0.96],[0.637,-0.953],[0.729,-1.044],[0.729,-1.086],[0.701,-1.128],[0.715,-1.198],[0.701,-1.268],[0.715,-1.282],[0.644,-1.352],[0.729,-1.436],[0.729,-1.52],[0.701,-1.548],[0.687,-1.716],[0.616,-1.786],[0.616,-1.912],[0.651,-1.905],[0.687,-1.94],[0.729,-1.982],[0.729,-2.024],[0.651,-2.102],[0.616,-2.109],[0.616,-2.319],[0.672,-2.375],[0.658,-2.431],[0.708,-2.438],[0.736,-2.466],[1.45,-2.466],[1.506,-2.452],[1.52,-2.466],[1.618,-2.466],[1.632,-2.452],[2.277,-2.452],[2.291,-2.438],[2.305,-2.452],[3.748,-2.438],[3.762,-2.452],[3.93,-2.452],[3.944,-2.438],[4.098,-2.438],[4.196,-2.452],[4.21,-2.438],[4.42,-2.438],[4.448,-2.452],[4.462,-2.438],[5.051,-2.438],[5.079,-2.466],[6.298,-2.466],[6.326,-2.452],[6.34,-2.466],[6.592,-2.466],[6.62,-2.438],[6.9,-2.438],[6.914,-2.424],[6.942,-2.438],[7.783,-2.424],[7.797,-2.438],[8.763,-2.438],[8.777,-2.424],[9.338,-2.424],[9.352,-2.41],[9.478,-2.438],[9.618,-2.424],[9.632,-2.438],[10.024,-2.438],[10.066,-2.424],[10.108,-2.438],[10.136,-2.424],[10.15,-2.438],[10.291,-2.438],[10.445,-2.48],[10.599,-2.648],[10.697,-2.648],[10.725,-2.62],[10.781,-2.634],[10.809,-2.62],[10.844,-2.571],[10.858,-2.319],[10.872,-2.305],[10.858,-2.109],[10.9,-2.067],[10.858,-2.024],[10.83,-1.912],[10.844,-1.884],[10.816,-1.856],[10.83,-1.772],[10.816,-1.702],[10.83,-1.688],[10.816,-1.646],[10.858,-1.604],[10.816,-1.562],[10.788,-1.45],[10.816,-1.422],[10.816,-1.1],[10.802,-1.072],[10.816,-0.974],[10.788,-0.946],[10.816,-0.862],[10.816,-0.764],[10.767,-0.771],[10.676,-0.679],[10.704,-0.651],[10.704,-0.567],[10.585,-0.462],[10.571,-0.476],[10.192,-0.476],[10.178,-0.49],[9.478,-0.49],[9.38,-0.392],[9.352,-0.42],[9.338,-0.406],[9.268,-0.448],[9.177,-0.357],[9.191,-0.287],[9.135,-0.231],[9.149,-0.203],[9.079,-0.133],[9.051,-0.049],[9.002,0],[8.918,0],[8.791,-0.084],[8.469,-0.07],[8.455,-0.084],[7.362,-0.084],[7.348,-0.098],[7.334,-0.084],[6.326,-0.098],[6.228,-0.084],[6.214,-0.098],[4.252,-0.098],[4.21,-0.112],[4.196,-0.098],[4.14,-0.112],[4.098,-0.098],[4.056,-0.14],[4.028,-0.112],[2.305,-0.112],[2.263,-0.154],[2.235,-0.126],[2.193,-0.14],[2.081,-0.14],[2.067,-0.126],[0.736,-0.126],[0.637,-0.14],[0.623,-0.126],[0.525,-0.14],[0.511,-0.126],[0.091,-0.126],[0.021,-0.168]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"x":"outline_rear_x","y":"top_above_axis"}}},"bounds":{"min":[-0.56,-1.3834,-0.9855],"max":[10.3077,1.237,0.9855]},"volume_in3":10.026,"centroid":[4.8582,-0.1692,0],"shell":[4.7432,-0.2311,0.0001],"area_in2":202.0922,"triangles":36748,"manifold":true,"slabs":[[-0.56,-1.181,-0.9,7.979,1.14,0.9],[7.979,-1.18,-0.985,8.755,1.237,0.985],[8.755,-1.226,-0.985,9.92,0.739,0.985],[9.92,-1.383,-0.985,10.308,0.739,0.985]],"slots":["body","heat_shield"]},"magpul-moe-trigger-guard":{"part":"magpul-moe-trigger-guard","model":"magpul-moe-trigger-guard.glb","script":"magpul_moe_trigger_guard.py","inputs":{"magpul-moe-trigger-guard.front_ahead_of_hole":0.143},"profiles":{"side":[[-2.154,-0.105],[-2.117,-0.142],[-1.3,-0.337],[-1.019,-0.363],[0.122,-0.175],[0.141,-0.147],[0.143,0.042],[0.141,0.09],[0.122,0.109],[-0.1,0.111],[-0.272,-0.036],[-0.437,-0.115],[-0.93,-0.204],[-1.098,-0.21],[-1.236,-0.185],[-1.35,-0.142],[-1.75,0.122],[-2.115,0.124],[-2.15,0.104]],"plan":[[-2.297,0.007],[-2.289,-0.198],[-2.276,-0.212],[-1.984,-0.214],[-1.919,-0.27],[-1.779,-0.308],[-0.72,-0.315],[-0.301,-0.312],[-0.276,-0.289],[-0.269,-0.236],[-0.25,-0.22],[-0.016,-0.218],[0,-0.008],[-0.012,0.023],[-0.01,0.212],[-0.264,0.223],[-0.273,0.286],[-0.3,0.311],[-1.689,0.315],[-1.86,0.298],[-1.952,0.258],[-1.977,0.226],[-2.283,0.224]]},"features":{"side":{},"plan":{}},"placement":{"side":{"plane":"xy","offset":{}},"plan":{"plane":"xz","offset":{"x":"front_ahead_of_hole"}}},"bounds":{"min":[-2.154,-0.363,-0.315],"max":[0.143,0.124,0.315]},"volume_in3":0.2831,"centroid":[-1.0539,-0.1382,0.0015],"shell":[-1.0027,-0.1431,0.0014],"area_in2":4.0037,"triangles":712,"manifold":true,"slabs":[[-2.154,-0.225,-0.271,-1.771,0.124,0.274],[-1.771,-0.316,-0.31,-1.388,0.122,0.315],[-1.388,-0.363,-0.315,-0.623,-0.117,0.315],[-0.623,-0.298,-0.315,-0.24,-0.008,0.312],[-0.24,-0.235,-0.313,0.143,0.111,0.311]],"slots":["body"]},"magpul-pmag-20-gen-m3":{"part":"magpul-pmag-20-gen-m3","model":"magpul-pmag-20-gen-m3.glb","script":"magpul_pmag_20_gen_m3.py","inputs":{"magpul-pmag-20-gen-m3.bars_front":10,"magpul-pmag-20-gen-m3.bars_spine":10,"magpul-pmag-20-gen-m3.catch_notch_front_x":0.974,"magpul-pmag-20-gen-m3.catch_notch_height":0.244,"magpul-pmag-20-gen-m3.catch_notch_rear_x":0.483,"magpul-pmag-20-gen-m3.catch_notch_top":1.055,"magpul-pmag-20-gen-m3.dot_depth":0.016,"magpul-pmag-20-gen-m3.dot_size":0.068,"magpul-pmag-20-gen-m3.dots_per_side":60,"magpul-pmag-20-gen-m3.frame_tab_corner_radius":0.03,"magpul-pmag-20-gen-m3.frame_tab_front":0.2,"magpul-pmag-20-gen-m3.frame_tab_lean":3.6,"magpul-pmag-20-gen-m3.frame_tab_length":0.226,"magpul-pmag-20-gen-m3.frame_tab_top":2.312,"magpul-pmag-20-gen-m3.front_bar_proud":0.014,"magpul-pmag-20-gen-m3.front_corner_depth":0.117,"magpul-pmag-20-gen-m3.front_strip_width":0.437,"magpul-pmag-20-gen-m3.guide_rib_lower_angle":19,"magpul-pmag-20-gen-m3.guide_rib_lower_height":0.102,"magpul-pmag-20-gen-m3.guide_rib_lower_top":1.996,"magpul-pmag-20-gen-m3.guide_rib_top_angle":29,"magpul-pmag-20-gen-m3.guide_rib_upper_height":0.133,"magpul-pmag-20-gen-m3.guide_rib_upper_top":0.48,"magpul-pmag-20-gen-m3.nose_front_width":0.526,"magpul-pmag-20-gen-m3.nose_round_depth":0.068,"magpul-pmag-20-gen-m3.nose_shoulder_width":0.7,"magpul-pmag-20-gen-m3.nose_taper_length":0.602,"magpul-pmag-20-gen-m3.rear_corner_depth":0.124,"magpul-pmag-20-gen-m3.rear_shoulder_width":0.545,"magpul-pmag-20-gen-m3.side_panel_corner_radius":0.08,"magpul-pmag-20-gen-m3.side_panel_depth":0.027,"magpul-pmag-20-gen-m3.side_panel_wall_run":0.027,"magpul-pmag-20-gen-m3.spine_bar_proud":0.022,"magpul-pmag-20-gen-m3.spine_depth":0.139,"magpul-pmag-20-gen-m3.spine_groove_length":0.938,"magpul-pmag-20-gen-m3.spine_groove_top":0.176,"magpul-pmag-20-gen-m3.spine_groove_width":0.048,"magpul-pmag-20-gen-m3.spine_groove_x":0.415,"magpul-pmag-20-gen-m3.spine_rib_width":0.148,"magpul-pmag-20-gen-m3.spine_strip_proud":0.072,"magpul-pmag-20-gen-m3.spine_width":0.438,"magpul-pmag-20-gen-m3.stop_bay_half_width":0.28,"magpul-pmag-20-gen-m3.stop_behind_spine":0.061,"magpul-pmag-20-gen-m3.stop_flat_half_width":0.287,"magpul-pmag-20-gen-m3.stop_half_width":0.426,"magpul-pmag-20-gen-m3.stop_length":0.224,"magpul-pmag-20-gen-m3.stop_lip_depth_end":0.128,"magpul-pmag-20-gen-m3.stop_lip_depth_middle":0.174,"magpul-pmag-20-gen-m3.stop_lip_end_half_width":0.385,"magpul-pmag-20-gen-m3.stop_lip_level_half_width":0.262,"magpul-pmag-20-gen-m3.stop_side_angle":18.4,"magpul-pmag-20-gen-m3.stop_wing_depth":0.169,"magpul-pmag-20-gen-m3.stop_wing_half_width":0.385,"magpul-pmag-20-gen-m3.strip_bar_thickness":0.034,"magpul-pmag-20-gen-m3.upper_rear_corner_radius":0.057,"std.ar15.mag_catch_slot_floor":0.3799},"profiles":{"side":[[-0.061,-3.124],[0.05,-3.381],[0.138,-4.199],[0.152,-4.287],[0.179,-4.315],[0.185,-4.428],[0.21,-4.522],[0.207,-4.58],[0.232,-4.676],[0.235,-4.759],[0.249,-4.781],[0.268,-4.889],[0.262,-4.925],[0.276,-4.944],[0.295,-5.049],[0.287,-5.074],[0.312,-5.132],[0.315,-5.201],[0.29,-5.295],[0.307,-5.408],[0.345,-5.549],[0.457,-5.6],[2.835,-5.131],[2.933,-5.03],[2.886,-4.787],[2.852,-4.729],[2.772,-4.27],[2.734,-4.016],[2.753,-3.986],[2.731,-3.831],[2.695,-3.793],[2.687,-3.735],[2.701,-3.718],[2.698,-3.691],[2.676,-3.644],[2.673,-3.605],[2.684,-3.594],[2.667,-3.577],[2.681,-3.564],[2.659,-3.511],[2.648,-3.423],[2.659,-3.392],[2.643,-3.359],[2.632,-3.268],[2.645,-3.254],[2.643,-3.224],[2.623,-3.193],[2.623,-3.169],[2.64,-3.152],[2.615,-3.122],[2.629,-3.094],[2.607,-3.025],[2.607,-3.003],[2.634,-2.97],[2.621,-2.801],[2.518,-2.705],[2.496,-2.647],[2.493,-0.211],[2.445,-0.174],[2.407,-0.185],[1.769,-0.138],[1.631,-0.091],[1.595,-0.099],[1.559,-0.091],[1.537,-0.102],[1.493,-0.091],[1.476,-0.102],[1.454,-0.091],[1.415,-0.105],[1.404,-0.094],[1.365,-0.094],[1.354,-0.105],[1.343,-0.094],[1.255,-0.08],[1.128,0],[0.189,0],[0.144,-0.026],[0.121,-0.261],[0.093,-0.29],[0.066,-0.297],[0.061,-0.418],[0.032,-0.447],[0,-0.457],[0.003,-2.97],[-0.058,-3.011]],"front":[[-0.552,-5.068],[-0.539,-5.397],[-0.549,-5.438],[-0.528,-5.498],[-0.423,-5.567],[-0.197,-5.6],[0.194,-5.6],[0.423,-5.567],[0.518,-5.505],[0.533,-5.482],[0.552,-5.202],[0.539,-4.911],[0.468,-4.81],[0.468,-4.247],[0.484,-4.157],[0.479,-2.914],[0.451,-2.765],[0.443,-0.233],[0.419,-0.135],[0.381,-0.08],[0.317,-0.027],[0.238,0],[0.215,-0.012],[0.215,-0.072],[0.201,-0.086],[0.233,-0.098],[0.256,-0.121],[0.254,-0.139],[0.276,-0.117],[0.31,-0.154],[0.281,-0.182],[0.257,-0.166],[0.214,-0.231],[0.189,-0.256],[0.166,-0.257],[0.18,-0.271],[0.135,-0.313],[0.11,-0.313],[0.088,-0.291],[0.067,-0.313],[-0.064,-0.313],[-0.088,-0.288],[-0.113,-0.313],[-0.165,-0.302],[-0.193,-0.273],[-0.171,-0.252],[-0.201,-0.216],[-0.218,-0.159],[-0.218,-0.015],[-0.241,0],[-0.314,-0.024],[-0.363,-0.06],[-0.419,-0.129],[-0.441,-0.192],[-0.446,-0.736],[-0.46,-0.915],[-0.449,-1.331],[-0.477,-1.36],[-0.506,-1.364],[-0.506,-1.484],[-0.449,-1.568],[-0.451,-2.332],[-0.462,-2.349],[-0.451,-2.37],[-0.462,-2.392],[-0.451,-2.414],[-0.454,-2.789],[-0.481,-2.917],[-0.484,-4.198],[-0.468,-4.261],[-0.468,-4.791],[-0.503,-4.862],[-0.549,-4.916],[-0.539,-4.94]],"left":[[-0.065,-3.033],[-0.062,-3.141],[0.046,-3.387],[0.143,-4.225],[0.141,-4.279],[0.176,-4.322],[0.181,-4.436],[0.211,-4.566],[0.206,-4.604],[0.227,-4.66],[0.233,-4.769],[0.249,-4.79],[0.262,-4.882],[0.257,-4.917],[0.276,-4.958],[0.289,-5.101],[0.314,-5.177],[0.287,-5.296],[0.303,-5.415],[0.341,-5.55],[0.45,-5.6],[2.819,-5.138],[2.849,-5.13],[2.931,-5.031],[2.912,-4.896],[2.88,-4.777],[2.855,-4.741],[2.801,-4.455],[2.734,-4.022],[2.75,-3.971],[2.731,-3.828],[2.69,-3.784],[2.685,-3.733],[2.696,-3.722],[2.696,-3.687],[2.677,-3.665],[2.666,-3.584],[2.68,-3.565],[2.677,-3.535],[2.658,-3.514],[2.65,-3.441],[2.663,-3.392],[2.639,-3.36],[2.634,-3.268],[2.645,-3.257],[2.639,-3.219],[2.623,-3.203],[2.615,-3.122],[2.628,-3.097],[2.604,-3.006],[2.634,-2.976],[2.62,-2.803],[2.515,-2.703],[2.496,-2.64],[2.493,-0.21],[2.454,-0.184],[1.764,-0.138],[1.713,-0.13],[1.629,-0.092],[1.535,-0.1],[1.521,-0.087],[1.475,-0.103],[1.456,-0.092],[1.416,-0.103],[1.294,-0.095],[1.132,0],[0.18,0],[0.158,-0.008],[0.138,-0.037],[0.141,-0.096],[0.116,-0.261],[0.088,-0.289],[0.062,-0.296],[0.057,-0.418],[0,-0.458],[0,-2.97],[-0.034,-3.004],[-0.055,-3.01]],"rear":[[-0.55,-4.909],[-0.536,-4.933],[-0.55,-5.061],[-0.55,-5.3],[-0.531,-5.479],[-0.424,-5.559],[-0.196,-5.592],[0.217,-5.589],[0.228,-5.6],[0.247,-5.584],[0.424,-5.559],[0.526,-5.49],[0.545,-5.332],[0.55,-5.08],[0.536,-4.901],[0.463,-4.792],[0.463,-4.271],[0.477,-4.184],[0.479,-2.986],[0.474,-2.875],[0.452,-2.763],[0.439,-0.194],[0.411,-0.113],[0.353,-0.054],[0.288,-0.014],[0.228,0],[0.21,-0.02],[0.216,-0.058],[0.189,-0.086],[0.216,-0.115],[0.191,-0.251],[0.152,-0.296],[0.115,-0.289],[0.137,-0.314],[0.148,-0.354],[0.124,-0.387],[0.148,-0.414],[0.117,-0.445],[-0.114,-0.445],[-0.143,-0.417],[-0.121,-0.392],[-0.151,-0.363],[-0.14,-0.352],[-0.143,-0.311],[-0.105,-0.284],[-0.118,-0.268],[-0.105,-0.254],[-0.147,-0.263],[-0.197,-0.224],[-0.219,-0.151],[-0.219,-0.012],[-0.236,0],[-0.312,-0.024],[-0.373,-0.069],[-0.43,-0.162],[-0.444,-0.235],[-0.444,-0.678],[-0.458,-0.889],[-0.449,-1.329],[-0.478,-1.358],[-0.504,-1.362],[-0.501,-1.495],[-0.449,-1.563],[-0.452,-2.763],[-0.479,-2.975],[-0.474,-4.181],[-0.485,-4.192],[-0.468,-4.216],[-0.485,-4.235],[-0.466,-4.254],[-0.466,-4.797]]},"features":{"side":{"dots":[[[0.653,-4.519],[0.639,-4.434],[0.724,-4.42],[0.738,-4.505]],[[0.667,-4.617],[0.655,-4.532],[0.739,-4.52],[0.752,-4.605]],[[0.685,-4.719],[0.666,-4.633],[0.752,-4.614],[0.77,-4.7]],[[0.694,-4.812],[0.688,-4.726],[0.774,-4.719],[0.781,-4.805]],[[0.716,-4.913],[0.699,-4.828],[0.782,-4.812],[0.799,-4.896]],[[0.75,-4.505],[0.735,-4.42],[0.824,-4.405],[0.838,-4.49]],[[0.765,-4.602],[0.754,-4.516],[0.841,-4.505],[0.851,-4.592]],[[0.781,-4.703],[0.767,-4.615],[0.851,-4.601],[0.866,-4.688]],[[0.797,-4.798],[0.783,-4.714],[0.866,-4.7],[0.88,-4.785]],[[0.809,-4.894],[0.8,-4.809],[0.884,-4.8],[0.893,-4.884]],[[0.85,-4.493],[0.833,-4.405],[0.919,-4.388],[0.936,-4.475]],[[0.866,-4.59],[0.848,-4.503],[0.935,-4.486],[0.952,-4.572]],[[0.879,-4.685],[0.866,-4.601],[0.952,-4.588],[0.965,-4.672]],[[0.894,-4.783],[0.879,-4.699],[0.966,-4.685],[0.981,-4.769]],[[0.908,-4.882],[0.896,-4.796],[0.979,-4.784],[0.992,-4.87]],[[0.995,-4.467],[0.982,-4.378],[1.068,-4.366],[1.081,-4.455]],[[1.01,-4.566],[0.996,-4.481],[1.084,-4.466],[1.098,-4.551]],[[1.027,-4.663],[1.013,-4.579],[1.098,-4.565],[1.112,-4.649]],[[1.04,-4.759],[1.029,-4.677],[1.111,-4.665],[1.123,-4.748]],[[1.054,-4.86],[1.043,-4.772],[1.128,-4.762],[1.139,-4.85]],[[1.174,-4.446],[1.088,-4.446],[1.088,-4.357],[1.174,-4.357]],[[1.107,-4.55],[1.097,-4.465],[1.182,-4.455],[1.193,-4.539]],[[1.121,-4.646],[1.111,-4.561],[1.198,-4.552],[1.207,-4.636]],[[1.138,-4.745],[1.126,-4.661],[1.212,-4.648],[1.224,-4.733]],[[1.152,-4.844],[1.141,-4.755],[1.224,-4.745],[1.235,-4.834]],[[1.192,-4.439],[1.177,-4.354],[1.262,-4.339],[1.277,-4.425]],[[1.208,-4.535],[1.194,-4.45],[1.279,-4.436],[1.293,-4.521]],[[1.222,-4.633],[1.207,-4.549],[1.292,-4.534],[1.307,-4.618]],[[1.236,-4.733],[1.222,-4.647],[1.309,-4.633],[1.324,-4.718]],[[1.25,-4.833],[1.237,-4.743],[1.325,-4.73],[1.338,-4.821]],[[1.34,-4.416],[1.33,-4.329],[1.413,-4.319],[1.423,-4.405]],[[1.352,-4.511],[1.34,-4.428],[1.426,-4.416],[1.438,-4.499]],[[1.373,-4.618],[1.352,-4.531],[1.438,-4.509],[1.46,-4.597]],[[1.385,-4.709],[1.37,-4.623],[1.455,-4.609],[1.47,-4.695]],[[1.399,-4.808],[1.384,-4.724],[1.47,-4.709],[1.485,-4.793]],[[1.44,-4.401],[1.423,-4.317],[1.507,-4.3],[1.524,-4.384]],[[1.452,-4.497],[1.437,-4.413],[1.523,-4.398],[1.538,-4.483]],[[1.467,-4.596],[1.455,-4.51],[1.541,-4.497],[1.553,-4.584]],[[1.48,-4.693],[1.469,-4.607],[1.556,-4.597],[1.567,-4.682]],[[1.496,-4.792],[1.484,-4.707],[1.57,-4.695],[1.583,-4.78]],[[1.536,-4.384],[1.522,-4.301],[1.605,-4.287],[1.619,-4.37]],[[1.548,-4.483],[1.539,-4.395],[1.624,-4.386],[1.633,-4.474]],[[1.565,-4.582],[1.55,-4.494],[1.636,-4.48],[1.65,-4.568]],[[1.581,-4.679],[1.569,-4.594],[1.654,-4.582],[1.666,-4.667]],[[1.594,-4.775],[1.583,-4.689],[1.669,-4.678],[1.68,-4.764]],[[1.684,-4.362],[1.671,-4.276],[1.754,-4.265],[1.766,-4.351]],[[1.698,-4.461],[1.686,-4.375],[1.769,-4.363],[1.781,-4.449]],[[1.792,-4.553],[1.707,-4.553],[1.707,-4.468],[1.792,-4.468]],[[1.727,-4.659],[1.713,-4.574],[1.799,-4.559],[1.813,-4.645]],[[1.74,-4.754],[1.728,-4.669],[1.815,-4.657],[1.827,-4.742]],[[1.78,-4.348],[1.768,-4.262],[1.853,-4.249],[1.865,-4.336]],[[1.796,-4.446],[1.785,-4.357],[1.868,-4.347],[1.879,-4.436]],[[1.814,-4.546],[1.797,-4.463],[1.879,-4.445],[1.897,-4.528]],[[1.825,-4.641],[1.813,-4.556],[1.898,-4.544],[1.91,-4.629]],[[1.843,-4.742],[1.827,-4.655],[1.912,-4.64],[1.927,-4.727]],[[1.878,-4.334],[1.866,-4.246],[1.951,-4.233],[1.964,-4.322]],[[1.892,-4.43],[1.882,-4.346],[1.968,-4.336],[1.979,-4.42]],[[1.906,-4.526],[1.9,-4.442],[1.987,-4.435],[1.993,-4.519]],[[1.923,-4.624],[1.913,-4.541],[1.995,-4.531],[2.006,-4.614]],[[1.937,-4.726],[1.926,-4.638],[2.011,-4.628],[2.021,-4.715]]]},"front":{"bars":[[[0.205,-3.068],[-0.209,-3.068],[-0.209,-3.102],[0.205,-3.102]],[[0.205,-3.223],[-0.209,-3.223],[-0.209,-3.257],[0.205,-3.257]],[[0.205,-3.377],[-0.209,-3.377],[-0.209,-3.409],[0.205,-3.409]],[[0.205,-3.53],[-0.209,-3.53],[-0.209,-3.564],[0.205,-3.564]],[[0.205,-3.685],[-0.209,-3.685],[-0.209,-3.721],[0.205,-3.721]],[[0.205,-4.078],[-0.209,-4.078],[-0.209,-4.111],[0.205,-4.111]],[[0.205,-4.232],[-0.209,-4.232],[-0.209,-4.266],[0.205,-4.266]],[[0.205,-4.384],[-0.209,-4.384],[-0.209,-4.418],[0.205,-4.418]],[[0.205,-4.539],[-0.209,-4.539],[-0.209,-4.572],[0.205,-4.572]],[[0.205,-4.693],[-0.209,-4.693],[-0.209,-4.726],[0.205,-4.726]]]},"left":{"panels_front":[[[2.962,-2.96],[2.343,-3.008],[2.384,-3.828],[3.019,-3.776]],[[3.071,-4.011],[2.459,-4.072],[2.558,-4.746],[3.071,-4.647]]],"panels_middle":[[[2.146,-3.049],[0.904,-3.135],[0.964,-3.987],[2.208,-3.876]]],"panels_rear":[[[0.694,-3.168],[-0.283,-3.243],[-0.283,-4.117],[0.769,-4.036]]],"panel_dots":[[[2.274,-4.092],[-0.174,-4.356],[-0.174,-5.276],[2.371,-4.775]]],"above_frame":[[[2.849,-2.789],[-0.282,-3.008],[-0.282,-2.459],[2.849,-2.459]]],"floorplate_joint":[[[3.119,-4.739],[-0.288,-5.409],[-0.288,-4.541],[3.119,-4.541]]],"catch_notch":[[[1.013,-1.107],[0.491,-1.107],[0.491,-1.359],[1.013,-1.359]]],"catch_block":[[[0.95,-1.359],[0.55,-1.359],[0.55,-1.553],[0.95,-1.553]]],"dots":[[[1.939,-4.729],[2.022,-4.715],[2.008,-4.63],[1.925,-4.644]],[[1.926,-4.631],[2.009,-4.614],[1.992,-4.531],[1.909,-4.547]],[[1.909,-4.535],[1.994,-4.518],[1.977,-4.432],[1.892,-4.449]],[[1.894,-4.436],[1.979,-4.42],[1.963,-4.335],[1.879,-4.351]],[[1.88,-4.337],[1.964,-4.32],[1.947,-4.234],[1.863,-4.252]],[[1.838,-4.743],[1.923,-4.731],[1.911,-4.647],[1.827,-4.658]],[[1.821,-4.645],[1.908,-4.633],[1.896,-4.548],[1.809,-4.56]],[[1.808,-4.546],[1.893,-4.534],[1.881,-4.45],[1.797,-4.462]],[[1.794,-4.449],[1.88,-4.436],[1.867,-4.351],[1.781,-4.364]],[[1.775,-4.35],[1.863,-4.34],[1.853,-4.253],[1.765,-4.263]],[[1.739,-4.758],[1.824,-4.749],[1.814,-4.661],[1.729,-4.671]],[[1.725,-4.66],[1.811,-4.647],[1.799,-4.563],[1.713,-4.575]],[[1.711,-4.562],[1.794,-4.551],[1.782,-4.465],[1.698,-4.476]],[[1.694,-4.464],[1.78,-4.451],[1.768,-4.365],[1.681,-4.377]],[[1.682,-4.364],[1.765,-4.352],[1.753,-4.268],[1.669,-4.28]],[[1.593,-4.783],[1.678,-4.771],[1.665,-4.682],[1.581,-4.694]],[[1.577,-4.681],[1.662,-4.67],[1.651,-4.585],[1.566,-4.596]],[[1.563,-4.587],[1.649,-4.574],[1.636,-4.488],[1.55,-4.5]],[[1.548,-4.485],[1.633,-4.473],[1.621,-4.389],[1.536,-4.401]],[[1.532,-4.387],[1.619,-4.377],[1.609,-4.292],[1.522,-4.302]],[[1.494,-4.795],[1.58,-4.783],[1.568,-4.697],[1.482,-4.71]],[[1.477,-4.698],[1.565,-4.685],[1.553,-4.6],[1.464,-4.612]],[[1.466,-4.599],[1.552,-4.585],[1.538,-4.501],[1.452,-4.515]],[[1.45,-4.501],[1.535,-4.489],[1.523,-4.403],[1.438,-4.415]],[[1.439,-4.405],[1.523,-4.387],[1.505,-4.301],[1.421,-4.319]],[[1.398,-4.812],[1.483,-4.796],[1.467,-4.711],[1.383,-4.727]],[[1.381,-4.711],[1.468,-4.7],[1.457,-4.614],[1.37,-4.625]],[[1.366,-4.613],[1.452,-4.601],[1.44,-4.517],[1.354,-4.529]],[[1.352,-4.515],[1.438,-4.503],[1.426,-4.419],[1.34,-4.431]],[[1.336,-4.416],[1.421,-4.406],[1.41,-4.32],[1.326,-4.331]],[[1.25,-4.834],[1.336,-4.819],[1.321,-4.733],[1.236,-4.747]],[[1.237,-4.737],[1.321,-4.72],[1.304,-4.635],[1.22,-4.652]],[[1.218,-4.636],[1.304,-4.624],[1.292,-4.538],[1.205,-4.55]],[[1.206,-4.537],[1.29,-4.525],[1.277,-4.441],[1.194,-4.453]],[[1.189,-4.439],[1.275,-4.427],[1.263,-4.342],[1.177,-4.354]],[[1.148,-4.848],[1.235,-4.838],[1.225,-4.751],[1.138,-4.761]],[[1.138,-4.749],[1.222,-4.735],[1.208,-4.651],[1.124,-4.665]],[[1.123,-4.653],[1.207,-4.641],[1.195,-4.554],[1.111,-4.566]],[[1.108,-4.555],[1.192,-4.539],[1.177,-4.454],[1.092,-4.469]],[[1.092,-4.456],[1.176,-4.444],[1.164,-4.357],[1.08,-4.369]],[[1.055,-4.864],[1.139,-4.847],[1.123,-4.763],[1.038,-4.78]],[[1.038,-4.764],[1.123,-4.752],[1.111,-4.666],[1.026,-4.678]],[[1.024,-4.666],[1.107,-4.654],[1.095,-4.569],[1.012,-4.581]],[[1.008,-4.567],[1.093,-4.555],[1.081,-4.47],[0.996,-4.482]],[[0.995,-4.472],[1.08,-4.457],[1.065,-4.37],[0.979,-4.386]],[[0.906,-4.885],[0.99,-4.873],[0.978,-4.787],[0.893,-4.799]],[[0.89,-4.786],[0.976,-4.774],[0.964,-4.689],[0.878,-4.701]],[[0.877,-4.689],[0.961,-4.674],[0.946,-4.589],[0.862,-4.604]],[[0.86,-4.59],[0.945,-4.579],[0.934,-4.494],[0.85,-4.504]],[[0.845,-4.492],[0.931,-4.479],[0.918,-4.393],[0.832,-4.406]],[[0.807,-4.899],[0.892,-4.887],[0.879,-4.8],[0.795,-4.813]],[[0.793,-4.803],[0.879,-4.788],[0.865,-4.703],[0.779,-4.717]],[[0.777,-4.703],[0.862,-4.691],[0.85,-4.606],[0.765,-4.618]],[[0.765,-4.607],[0.85,-4.59],[0.833,-4.505],[0.748,-4.522]],[[0.744,-4.504],[0.83,-4.499],[0.824,-4.411],[0.738,-4.417]],[[0.71,-4.915],[0.796,-4.902],[0.784,-4.817],[0.698,-4.829]],[[0.692,-4.814],[0.779,-4.805],[0.769,-4.72],[0.683,-4.729]],[[0.681,-4.721],[0.766,-4.706],[0.751,-4.619],[0.666,-4.635]],[[0.665,-4.62],[0.751,-4.607],[0.739,-4.522],[0.652,-4.535]],[[0.652,-4.523],[0.736,-4.509],[0.721,-4.423],[0.637,-4.438]]]},"rear":{"bars":[[[-0.201,-3.306],[0.198,-3.306],[0.198,-3.34],[-0.201,-3.34]],[[-0.201,-3.468],[0.198,-3.468],[0.198,-3.499],[-0.201,-3.499]],[[-0.201,-3.63],[0.198,-3.63],[0.198,-3.664],[-0.201,-3.664]],[[-0.201,-3.795],[0.198,-3.795],[0.198,-3.827],[-0.201,-3.827]],[[-0.201,-3.956],[0.198,-3.956],[0.198,-3.988],[-0.201,-3.988]],[[-0.201,-4.409],[0.198,-4.409],[0.198,-4.438],[-0.201,-4.438]],[[-0.201,-4.569],[0.198,-4.569],[0.198,-4.603],[-0.201,-4.603]],[[-0.201,-4.734],[0.198,-4.734],[0.198,-4.761],[-0.201,-4.761]],[[-0.201,-4.893],[0.198,-4.893],[0.198,-4.924],[-0.201,-4.924]],[[-0.201,-5.055],[0.198,-5.055],[0.198,-5.087],[-0.201,-5.087]]],"rib":[[[-0.075,-3.131],[0.073,-3.131],[0.073,-4.101],[-0.075,-4.101]]]}},"placement":{"side":{"plane":"xy","offset":{}},"front":{"plane":"zy","offset":{}},"left":{"plane":"xy","offset":{}},"rear":{"plane":"zy","offset":{}}},"bounds":{"min":[-0.061,-5.6,-0.552],"max":[2.933,0,0.552]},"volume_in3":11.658,"centroid":[1.3498,-2.8849,-0.0007],"shell":[1.3294,-2.798,0.0003],"area_in2":43.5199,"triangles":7348,"manifold":true,"slabs":[[0.29,-5.6,-0.549,2.485,-5.2,0.551],[0.248,-5.2,-0.552,2.933,-4.8,0.551],[0.17,-4.8,-0.482,2.889,-4.4,0.481],[0.117,-4.4,-0.482,2.809,-4,0.481],[0.074,-4,-0.482,2.753,-3.6,0.481],[-0.061,-3.6,-0.482,2.677,-2.8,0.481],[0.002,-2.8,-0.457,2.62,-2.4,0.454],[0,-2.4,-0.451,2.496,-0.4,0.45],[0.062,-0.4,-0.443,2.493,0,0.444]],"slots":["body"]},"magpul-pmag-30-gen-m3":{"part":"magpul-pmag-30-gen-m3","model":"magpul-pmag-30-gen-m3.glb","script":"magpul_pmag_30_gen_m3.py","inputs":{"magpul-pmag-30-gen-m3.catch_notch_front_x":1.06,"magpul-pmag-30-gen-m3.catch_notch_height":0.25,"magpul-pmag-30-gen-m3.catch_notch_rear_x":0.55,"magpul-pmag-30-gen-m3.catch_notch_top":1.07,"magpul-pmag-30-gen-m3.dot_matrix_blocks":4,"magpul-pmag-30-gen-m3.dot_matrix_columns":3,"magpul-pmag-30-gen-m3.dot_matrix_dimple":0.068,"magpul-pmag-30-gen-m3.dot_matrix_pitch":0.101,"magpul-pmag-30-gen-m3.dot_matrix_rows":5,"magpul-pmag-30-gen-m3.frame_tab_corner_radius":0.03,"magpul-pmag-30-gen-m3.front_bar_proud":0.017,"magpul-pmag-30-gen-m3.front_corner_depth":0.115,"magpul-pmag-30-gen-m3.front_strip_width":0.44,"magpul-pmag-30-gen-m3.guide_rib_top_angle":29,"magpul-pmag-30-gen-m3.nose_front_width":0.526,"magpul-pmag-30-gen-m3.nose_round_depth":0.068,"magpul-pmag-30-gen-m3.nose_shoulder_width":0.7,"magpul-pmag-30-gen-m3.nose_taper_length":0.602,"magpul-pmag-30-gen-m3.rear_corner_depth":0.12,"magpul-pmag-30-gen-m3.rear_shoulder_width":0.554,"magpul-pmag-30-gen-m3.side_panel_corner_radius":0.08,"magpul-pmag-30-gen-m3.side_panel_depth":0.025,"magpul-pmag-30-gen-m3.side_panel_wall_run":0.026,"magpul-pmag-30-gen-m3.spine_ahead_of_stop":0.066,"magpul-pmag-30-gen-m3.spine_bar_proud":0.022,"magpul-pmag-30-gen-m3.spine_rib_width":0.151,"magpul-pmag-30-gen-m3.spine_strip_proud":0.07,"magpul-pmag-30-gen-m3.spine_strip_proud_upper":0.101,"magpul-pmag-30-gen-m3.spine_strip_width":0.442,"magpul-pmag-30-gen-m3.stop_bay_half_width":0.271,"magpul-pmag-30-gen-m3.stop_flat_half_width":0.304,"magpul-pmag-30-gen-m3.stop_half_width":0.431,"magpul-pmag-30-gen-m3.stop_length":0.206,"magpul-pmag-30-gen-m3.stop_lip_depth_end":0.103,"magpul-pmag-30-gen-m3.stop_lip_depth_middle":0.178,"magpul-pmag-30-gen-m3.stop_lip_end_half_width":0.385,"magpul-pmag-30-gen-m3.stop_lip_level_half_width":0.262,"magpul-pmag-30-gen-m3.stop_side_angle":18.3,"magpul-pmag-30-gen-m3.stop_wing_depth":0.156,"magpul-pmag-30-gen-m3.stop_wing_half_width":0.385,"magpul-pmag-30-gen-m3.strip_bar_thickness":0.036,"magpul-pmag-30-gen-m3.upper_rear_corner_radius":0.057,"std.ar15.mag_catch_slot_floor":0.3799},"profiles":{"side":[[0,-3.164],[0.141,-3.49],[0.13,-3.536],[0.15,-3.562],[0.162,-3.617],[0.144,-3.666],[0.15,-3.704],[0.17,-3.724],[0.179,-3.805],[0.164,-3.828],[0.196,-3.949],[0.182,-3.998],[0.211,-4.059],[0.202,-4.088],[0.211,-4.096],[0.188,-4.142],[0.231,-4.402],[0.237,-4.469],[0.225,-4.48],[0.251,-4.541],[0.378,-5.352],[0.387,-5.38],[0.421,-5.415],[0.439,-5.464],[0.424,-5.493],[0.462,-5.6],[0.459,-5.686],[0.485,-5.715],[0.496,-5.787],[0.485,-5.802],[0.531,-5.926],[0.519,-5.972],[0.548,-6.015],[0.56,-6.07],[0.551,-6.125],[0.586,-6.188],[0.571,-6.212],[0.586,-6.232],[0.566,-6.258],[0.586,-6.327],[0.571,-6.35],[0.6,-6.382],[0.609,-6.437],[0.658,-6.489],[0.649,-6.529],[0.693,-6.639],[0.69,-6.702],[0.733,-6.797],[0.724,-6.843],[0.765,-6.89],[0.785,-6.959],[0.765,-6.988],[0.768,-7.011],[0.808,-7.054],[0.834,-7.144],[0.805,-7.187],[0.863,-7.4],[0.988,-7.48],[1.026,-7.497],[1.066,-7.491],[1.075,-7.5],[1.112,-7.474],[1.306,-7.419],[1.329,-7.431],[1.378,-7.399],[3.314,-6.851],[3.36,-6.831],[3.417,-6.777],[3.437,-6.728],[3.443,-6.65],[3.394,-6.486],[3.402,-6.465],[3.366,-6.424],[3.337,-6.421],[3.304,-6.388],[3.307,-6.338],[3.278,-6.301],[3.264,-6.235],[3.235,-6.197],[3.215,-6.131],[3.244,-6.093],[3.232,-6.056],[3.206,-6.03],[3.194,-5.972],[3.209,-5.955],[3.2,-5.914],[3.171,-5.88],[3.169,-5.854],[3.192,-5.831],[3.186,-5.787],[3.154,-5.663],[3.114,-5.629],[3.105,-5.597],[3.119,-5.577],[3.079,-5.487],[3.076,-5.455],[3.091,-5.438],[3.082,-5.404],[3.053,-5.369],[3.056,-5.285],[3.018,-5.199],[3.033,-5.167],[3.021,-5.126],[2.998,-5.103],[2.99,-5.049],[3.004,-5.034],[3.001,-5.005],[2.969,-4.939],[2.992,-4.904],[2.972,-4.783],[2.987,-4.757],[2.929,-4.705],[2.923,-4.685],[2.929,-4.61],[2.906,-4.587],[2.894,-4.541],[2.912,-4.515],[2.909,-4.466],[2.88,-4.437],[2.883,-4.33],[2.857,-4.298],[2.851,-4.261],[2.866,-4.229],[2.837,-4.16],[2.834,-4.125],[2.848,-4.111],[2.814,-3.998],[2.842,-3.964],[2.828,-3.834],[2.819,-3.799],[2.779,-3.756],[2.788,-3.672],[2.77,-3.655],[2.762,-3.588],[2.776,-3.554],[2.744,-3.47],[2.762,-3.418],[2.759,-3.395],[2.733,-3.366],[2.727,-3.32],[2.747,-3.291],[2.741,-3.257],[2.721,-3.233],[2.715,-3.17],[2.73,-3.153],[2.704,-3.066],[2.704,-3.04],[2.73,-3.008],[2.718,-2.832],[2.617,-2.743],[2.594,-2.694],[2.594,-0.302],[2.586,-0.203],[2.547,-0.182],[1.41,-0.104],[1.291,-0.052],[1.222,0],[0.232,0],[0.205,-0.03],[0.208,-0.085],[0.167,-0.414],[0.134,-0.447],[0.079,-0.447],[0.066,-0.46],[0.069,-2.994],[0.036,-3.036],[0.006,-3.046]],"front":[[-0.586,-7.283],[-0.574,-7.366],[-0.526,-7.417],[-0.468,-7.451],[-0.332,-7.491],[-0.262,-7.5],[-0.219,-7.488],[0.225,-7.488],[0.277,-7.5],[0.489,-7.442],[0.559,-7.385],[0.58,-7.348],[0.586,-6.788],[0.577,-6.729],[0.531,-6.628],[0.46,-6.532],[0.46,-6.409],[0.475,-6.387],[0.488,-6.249],[0.479,-2.91],[0.488,-2.901],[0.46,-2.839],[0.457,-1.586],[0.509,-1.51],[0.512,-1.399],[0.508,-1.379],[0.489,-1.376],[0.457,-1.343],[0.463,-0.903],[0.451,-0.712],[0.451,-0.226],[0.432,-0.152],[0.386,-0.075],[0.335,-0.034],[0.243,0],[0.22,-0.011],[0.223,-0.14],[0.202,-0.192],[0.192,-0.269],[0.154,-0.311],[0.012,-0.314],[-0.02,-0.282],[-0.028,-0.243],[-0.049,-0.265],[-0.066,-0.254],[-0.038,-0.282],[-0.071,-0.314],[-0.111,-0.305],[-0.12,-0.314],[-0.132,-0.302],[-0.148,-0.314],[-0.183,-0.279],[-0.171,-0.263],[-0.205,-0.229],[-0.183,-0.208],[-0.22,-0.174],[-0.217,-0.014],[-0.246,0],[-0.329,-0.031],[-0.386,-0.075],[-0.423,-0.131],[-0.448,-0.205],[-0.457,-2.818],[-0.488,-2.95],[-0.479,-3.141],[-0.488,-4.132],[-0.479,-4.963],[-0.488,-5.166],[-0.479,-5.972],[-0.488,-6.003],[-0.488,-6.249],[-0.479,-6.258],[-0.472,-6.397],[-0.457,-6.412],[-0.457,-6.511],[-0.546,-6.658],[-0.583,-6.763]],"left":[[0,-3.067],[0.005,-3.159],[0.03,-3.184],[0.128,-3.434],[0.154,-3.473],[0.138,-3.511],[0.164,-3.543],[0.172,-3.606],[0.153,-3.672],[0.177,-3.697],[0.19,-3.795],[0.172,-3.819],[0.175,-3.84],[0.199,-3.858],[0.211,-3.949],[0.193,-3.973],[0.212,-4.006],[0.222,-4.082],[0.2,-4.128],[0.272,-4.666],[0.393,-5.354],[0.434,-5.398],[0.434,-5.497],[0.457,-5.516],[0.471,-5.62],[0.461,-5.65],[0.485,-5.668],[0.502,-5.744],[0.489,-5.803],[0.522,-5.841],[0.534,-5.925],[0.523,-5.955],[0.558,-6],[0.569,-6.084],[0.559,-6.113],[0.583,-6.132],[0.595,-6.173],[0.576,-6.239],[0.58,-6.267],[0.612,-6.398],[0.646,-6.443],[0.654,-6.506],[0.644,-6.536],[0.677,-6.567],[0.691,-6.622],[0.687,-6.694],[0.711,-6.712],[0.728,-6.844],[0.754,-6.876],[0.769,-6.931],[0.763,-6.996],[0.797,-7.034],[0.805,-7.097],[0.777,-7.257],[0.846,-7.454],[0.955,-7.5],[1.137,-7.476],[1.87,-7.27],[1.951,-7.238],[2.014,-7.23],[2.15,-7.183],[2.83,-7.006],[3.282,-6.874],[3.328,-6.847],[3.402,-6.741],[3.39,-6.7],[3.374,-6.688],[3.392,-6.664],[3.381,-6.53],[3.299,-6.342],[3.3,-6.299],[3.27,-6.232],[3.26,-6.155],[3.226,-6.068],[3.227,-6.018],[3.195,-5.937],[3.195,-5.887],[3.166,-5.827],[3.174,-5.783],[3.166,-5.72],[3.142,-5.652],[3.107,-5.6],[3.106,-5.543],[3.077,-5.483],[3.062,-5.372],[3.037,-5.297],[3.037,-5.24],[3.02,-5.221],[3.004,-5.102],[2.98,-5.027],[2.978,-4.963],[2.958,-4.916],[2.973,-4.871],[2.955,-4.739],[2.909,-4.66],[2.915,-4.595],[2.897,-4.569],[2.888,-4.449],[2.864,-4.374],[2.872,-4.33],[2.853,-4.297],[2.843,-4.221],[2.854,-4.198],[2.828,-4.166],[2.82,-4.103],[2.828,-4.059],[2.811,-4.033],[2.802,-3.97],[2.82,-3.946],[2.799,-3.786],[2.775,-3.768],[2.779,-3.746],[2.762,-3.727],[2.778,-3.682],[2.761,-3.663],[2.748,-3.565],[2.759,-3.542],[2.74,-3.509],[2.741,-3.409],[2.715,-3.321],[2.73,-3.276],[2.709,-3.222],[2.702,-3.173],[2.717,-3.128],[2.693,-3.053],[2.713,-2.987],[2.7,-2.839],[2.681,-2.806],[2.65,-2.789],[2.608,-2.738],[2.585,-2.67],[2.574,-2.38],[2.585,-2.3],[2.58,-2.109],[2.569,-2.082],[2.582,-1.696],[2.57,-1.505],[2.576,-0.651],[2.566,-0.575],[2.567,-0.425],[2.58,-0.359],[2.564,-0.191],[2.536,-0.17],[2.493,-0.161],[2.248,-0.137],[1.732,-0.107],[1.672,-0.087],[1.445,-0.089],[1.304,-0.051],[1.22,-0.005],[1.049,0],[0.609,-0.009],[0.295,-0.002],[0.218,-0.012],[0.204,-0.039],[0.197,-0.196],[0.177,-0.263],[0.184,-0.312],[0.172,-0.434],[0.157,-0.454],[0.08,-0.464],[0.073,-0.49],[0.075,-0.718],[0.088,-0.815],[0.074,-0.867],[0.073,-1.017],[0.081,-1.079],[0.068,-2.041],[0.076,-2.943],[0.07,-3.008],[0.055,-3.028],[0.014,-3.04]]},"features":{"side":{},"front":{},"left":{"panels_front":[[[2.942,-2.975],[2.393,-3.044],[2.496,-3.812],[3.046,-3.749]],[[3.072,-3.942],[2.523,-4.011],[2.626,-4.776],[3.174,-4.702]],[[3.201,-4.9],[2.707,-4.957],[2.808,-5.704],[3.301,-5.647]]],"panels_middle":[[[2.2,-3.059],[0.961,-3.155],[1.072,-3.982],[2.304,-3.834]],[[2.325,-4.045],[1.092,-4.207],[1.202,-5.024],[2.432,-4.841]],[[2.507,-5.027],[1.246,-5.218],[1.342,-5.937],[2.604,-5.749]]],"panels_rear":[[[0.731,-3.189],[-0.111,-3.274],[-0.004,-4.065],[0.819,-3.974]],[[0.855,-4.243],[0.035,-4.358],[0.146,-5.183],[0.958,-5.064]],[[1.055,-5.279],[0.175,-5.402],[0.287,-6.23],[1.152,-6.105]]],"panel_dots":[[[2.688,-5.969],[0.324,-6.509],[0.412,-7.161],[2.837,-6.507]]],"above_frame":[[[2.952,-2.786],[2.397,-2.83],[2.363,-2.324],[2.156,-2.327],[2.195,-2.846],[-0.179,-3.033],[-0.311,-2.049],[2.855,-2.064]]],"panel_front_low":[[[3.396,-5.82],[2.873,-5.89],[3.028,-6.537],[3.489,-6.512]]],"rim_low":[[[3.489,-6.512],[3.028,-6.537],[2.837,-6.507],[0.412,-7.161],[0.432,-7.309],[2.866,-6.637],[2.901,-6.847],[3.507,-6.645]]],"dot_blocks":[[[1.079,-6.465],[1.277,-6.414],[1.377,-6.805],[1.18,-6.855]],[[1.423,-6.376],[1.619,-6.326],[1.718,-6.714],[1.523,-6.764]],[[1.763,-6.286],[1.962,-6.235],[2.062,-6.624],[1.864,-6.675]],[[2.105,-6.191],[2.301,-6.141],[2.402,-6.533],[2.206,-6.584]]],"spine_groove":[[[0.446,-0.21],[0.489,-0.21],[0.489,-1.09],[0.446,-1.09]]],"guide_ribs":[[[1.85,-0.455],[2.75,-0.455],[2.75,-0.603],[1.85,-0.603]],[[1.85,-1.985],[2.75,-1.985],[2.75,-2.12],[1.85,-2.12]]],"bars_front":[[[2.711,-3.126],[2.724,-3.264],[2.739,-3.402],[2.754,-3.538],[2.772,-3.684]],[[2.827,-4.062],[2.847,-4.198],[2.866,-4.332],[2.89,-4.47],[2.914,-4.608]],[[2.981,-4.978],[3.003,-5.13],[3.033,-5.258],[3.065,-5.39],[3.094,-5.528]],[[3.186,-5.886],[3.22,-6.026],[3.253,-6.155],[3.292,-6.288]]],"bars_spine":[[[0.142,-3.516],[0.159,-3.672],[0.178,-3.828],[0.194,-3.982]],[[0.431,-5.484],[0.461,-5.64],[0.493,-5.792],[0.525,-5.946],[0.559,-6.102]],[[0.65,-6.526],[0.689,-6.686],[0.727,-6.834],[0.765,-6.986]]]}},"placement":{"side":{"plane":"xy","offset":{}},"front":{"plane":"zy","offset":{}},"left":{"plane":"xy","offset":{}}},"bounds":{"min":[0,-7.5,-0.586],"max":[3.443,0,0.586]},"volume_in3":16.3598,"centroid":[1.5615,-3.7903,0.0014],"shell":[1.5514,-3.7101,-0.0007],"area_in2":57.4236,"triangles":9646,"manifold":true,"slabs":[[0.805,-7.5,-0.586,2.417,-7.105,0.582],[0.718,-7.105,-0.585,3.438,-6.71,0.581],[0.594,-6.71,-0.495,3.443,-6.316,0.493],[0.511,-6.316,-0.488,3.262,-5.921,0.488],[0.45,-5.921,-0.484,3.192,-5.526,0.487],[0.343,-5.526,-0.488,3.103,-5.131,0.486],[0.282,-5.131,-0.486,3.021,-4.737,0.485],[0.221,-4.737,-0.486,2.942,-4.342,0.484],[0.176,-4.342,-0.488,2.881,-3.947,0.483],[0.144,-3.947,-0.486,2.828,-3.553,0.482],[0,-3.553,-0.488,2.77,-2.763,0.488],[0.066,-2.763,-0.457,2.64,-0.395,0.463],[0.169,-0.395,-0.449,2.594,0,0.451]],"slots":["body"]},"magpul-pmag-d-60":{"part":"magpul-pmag-d-60","model":"magpul-pmag-d-60.glb","script":"magpul_pmag_d_60.py","inputs":{"magpul-pmag-30-gen-m3.catch_notch_front_x":1.06,"magpul-pmag-30-gen-m3.catch_notch_height":0.25,"magpul-pmag-30-gen-m3.catch_notch_rear_x":0.55,"magpul-pmag-30-gen-m3.side_panel_depth":0.025,"magpul-pmag-30-gen-m3.spine_ahead_of_stop":0.066,"magpul-pmag-d-60.catch_notch_top":1.1,"magpul-pmag-d-60.clip_half_angle":13.6,"magpul-pmag-d-60.clip_inner_radius":1.56,"magpul-pmag-d-60.dot_group_gap":0.088,"magpul-pmag-d-60.dot_square":0.073,"magpul-pmag-d-60.drum_height":4.487,"magpul-pmag-d-60.front_hub_radius":0.495,"magpul-pmag-d-60.front_hub_rim_radius":0.607,"magpul-pmag-d-60.front_ring_radius":1.038,"magpul-pmag-d-60.front_to_back":2.528,"magpul-pmag-d-60.lips_slot_depth":0.31,"magpul-pmag-d-60.lips_slot_width":0.44,"magpul-pmag-d-60.overall_height":7.4,"magpul-pmag-d-60.seam_front_x":2.667,"magpul-pmag-d-60.seam_rear_x":0.59,"magpul-pmag-d-60.spine_ahead_of_rear":0.086,"magpul-pmag-d-60.spine_width":0.46,"magpul-pmag-d-60.stated_width":4.1,"magpul-pmag-d-60.tower_lean":10,"magpul-pmag-d-60.tower_width":0.875,"std.ar15.mag_catch_slot_floor":0.3799,"std.ar15.magwell_box_length":2.398,"std.ar15.magwell_length":2.553},"profiles":{"drum":[[0,4.217],[0.006,4.208],[0,4.165],[0.089,4.069],[0.074,4.044],[0.08,4.035],[0.068,3.84],[0.034,3.807],[0.022,3.751],[0.028,3.736],[0.022,3.726],[0.028,3.711],[0.022,3.702],[0.028,3.686],[0.022,3.677],[0.028,3.662],[0.022,3.652],[0.028,3.637],[0.022,3.628],[0.028,3.612],[0.022,3.603],[0.028,3.587],[0.022,3.578],[0.028,3.563],[0.022,3.553],[0.028,3.538],[0.022,3.529],[0.028,3.513],[0.022,3.504],[0.028,3.489],[0.022,3.174],[0.028,3.165],[0.009,2.995],[0.012,2.881],[0,2.834],[0.006,2.825],[0,2.785],[0.028,2.751],[0.025,1.325],[0.037,1.254],[0.031,1.242],[0.043,1.109],[0.022,1.079],[0.028,1.069],[0.022,1.06],[0.028,1.045],[0.022,1.035],[0.028,1.02],[0.022,1.011],[0.028,0.995],[0.022,0.986],[0.028,0.971],[0.022,0.961],[0.028,0.946],[0.022,0.937],[0.028,0.921],[0.022,0.912],[0.028,0.896],[0.022,0.887],[0.028,0.872],[0.022,0.863],[0.028,0.847],[0.022,0.838],[0.028,0.822],[0.022,0.813],[0.028,0.798],[0.022,0.788],[0.028,0.773],[0.022,0.764],[0.028,0.748],[0.022,0.739],[0.028,0.724],[0.022,0.714],[0.028,0.699],[0.022,0.69],[0.028,0.674],[0.022,0.665],[0.028,0.65],[0.022,0.64],[0.028,0.625],[0.022,0.616],[0.028,0.6],[0.022,0.591],[0.025,0.335],[0.031,0.307],[0.096,0.245],[0.105,0.103],[0.159,0.031],[0.313,0.022],[0.329,0.028],[0.523,0.009],[0.56,0.015],[0.603,0.009],[0.613,0],[0.631,0.015],[0.721,0.028],[0.733,0.022],[0.832,0.037],[0.921,0.037],[0.967,0.049],[1.008,0.046],[1.239,0.077],[1.329,0.074],[1.353,0.089],[1.369,0.083],[1.511,0.102],[1.523,0.096],[1.609,0.105],[1.625,0.114],[1.649,0.099],[1.668,0.114],[1.733,0.123],[1.77,0.12],[2.004,0.151],[2.094,0.148],[2.143,0.164],[2.159,0.157],[2.254,0.173],[2.291,0.148],[2.322,0.179],[2.362,0.185],[2.402,0.182],[2.523,0.201],[2.588,0.201],[2.609,0.21],[2.674,0.207],[3.075,0.25],[3.109,0.265],[3.444,0.588],[3.459,0.622],[3.472,0.687],[3.466,0.699],[3.496,0.835],[3.49,0.844],[3.512,0.924],[3.512,0.971],[3.521,0.983],[3.515,1.02],[3.564,1.446],[3.564,2.662],[3.515,3.091],[3.521,3.304],[3.512,3.316],[3.512,3.359],[3.586,3.489],[3.58,3.649],[3.595,3.674],[3.58,3.695],[3.586,3.856],[3.53,3.958],[3.461,4.024],[3.427,4.033],[3.319,4.03],[3.279,4.04],[3.266,4.033],[3.128,4.095],[3.106,4.114],[3.094,4.111],[3.057,4.135],[2.856,4.141],[2.855,4.013],[2.801,3.959],[2.705,3.969],[2.651,4.029],[2.654,4.149],[2.648,4.155],[2.657,4.168],[2.629,4.214],[2.555,4.282],[2.56,4.32],[2.532,4.293],[2.501,4.32],[2.443,4.262],[2.43,4.262],[2.412,4.243],[2.396,4.259],[2.365,4.262],[2.31,4.256],[2.294,4.24],[2.279,4.256],[2.227,4.252],[2.211,4.237],[2.199,4.249],[2.156,4.252],[2.131,4.234],[2.112,4.249],[2.06,4.249],[2.044,4.237],[1.995,4.286],[1.946,4.237],[1.93,4.249],[1.921,4.243],[1.878,4.249],[1.862,4.234],[1.838,4.249],[1.822,4.243],[1.801,4.249],[1.779,4.234],[1.764,4.249],[1.745,4.243],[1.708,4.249],[1.696,4.237],[1.683,4.249],[1.674,4.243],[1.631,4.249],[1.612,4.234],[1.591,4.249],[1.575,4.243],[1.554,4.249],[1.535,4.231],[1.517,4.249],[1.498,4.243],[1.461,4.249],[1.452,4.24],[1.44,4.249],[1.427,4.243],[1.384,4.249],[1.362,4.231],[1.344,4.249],[1.329,4.243],[1.307,4.249],[1.285,4.234],[1.27,4.249],[1.251,4.243],[1.214,4.249],[1.202,4.237],[1.19,4.249],[1.18,4.243],[1.137,4.249],[1.116,4.231],[1.097,4.249],[1.082,4.243],[1.06,4.249],[1.038,4.237],[1.023,4.249],[1.004,4.243],[0.967,4.249],[0.955,4.237],[0.943,4.249],[0.934,4.243],[0.89,4.249],[0.875,4.234],[0.85,4.249],[0.835,4.243],[0.813,4.249],[0.795,4.231],[0.776,4.249],[0.758,4.243],[0.721,4.249],[0.708,4.237],[0.696,4.249],[0.687,4.243],[0.643,4.249],[0.622,4.231],[0.603,4.249],[0.588,4.243],[0.569,4.249],[0.523,4.246],[0.511,4.234],[0.498,4.243],[0.44,4.24],[0.427,4.228],[0.412,4.24],[0.375,4.231],[0.36,4.237],[0.344,4.222],[0.332,4.234],[0.316,4.234],[0.273,4.274],[0.275,4.254],[0.224,4.203],[0.177,4.2],[0.153,4.181],[0.096,4.245],[0.114,4.266],[0.102,4.285],[0.12,4.303],[0.111,4.313],[0.136,4.337],[0.13,4.347],[0.199,4.416],[0.25,4.377],[0.241,4.476],[0.218,4.487],[0.181,4.456],[0.162,4.459],[0.134,4.487],[0.116,4.468],[0.091,4.487],[0.063,4.459],[0.037,4.452],[0.009,4.282],[0.012,4.239]],"rear":[[-2.052,1.959],[-2.027,1.74],[-1.959,1.453],[-1.877,1.234],[-1.778,1.04],[-1.815,0.884],[-1.859,0.753],[-1.852,0.653],[-1.746,0.515],[-1.543,0.312],[-1.425,0.212],[-1.381,0.194],[-1.187,0.225],[-1.05,0.262],[-1.031,0.275],[-1.006,0.275],[-0.856,0.187],[-0.625,0.094],[-0.575,0.087],[-0.556,0.075],[-0.456,0.05],[-0.281,0.019],[0,0],[0.156,0],[0.306,0.019],[0.612,0.087],[0.687,0.125],[0.856,0.187],[0.981,0.262],[1,0.262],[1.037,0.237],[1.062,0.237],[1.156,0.206],[1.218,0.2],[1.306,0.175],[1.35,0.175],[1.381,0.187],[1.531,0.306],[1.734,0.509],[1.821,0.622],[1.834,0.69],[1.828,0.747],[1.79,0.865],[1.771,0.965],[1.759,0.984],[1.759,1.015],[1.828,1.134],[1.884,1.259],[1.99,1.578],[2.034,1.815],[2.052,2.077],[2.034,2.327],[1.965,2.646],[1.865,2.902],[1.771,3.071],[1.852,3.383],[1.852,3.421],[1.821,3.483],[1.746,3.577],[1.543,3.78],[1.393,3.905],[1.343,3.917],[1.25,3.886],[1.15,3.867],[1.087,3.842],[1.006,3.83],[0.9,3.886],[0.872,3.914],[0.865,3.964],[0.84,4.014],[0.772,4.077],[0.772,4.089],[0.756,4.105],[0.712,4.13],[0.631,4.142],[0.594,4.161],[0.581,4.149],[0.556,4.18],[0.5,4.192],[0.44,4.227],[0.447,6.22],[0.44,6.226],[0.447,6.239],[0.434,6.495],[0.428,7.213],[0.369,7.323],[0.331,7.354],[0.281,7.379],[0.231,7.385],[0.222,7.376],[0.222,7.257],[0.203,7.226],[0.172,7.126],[0.125,7.091],[0.056,7.091],[0.041,7.107],[0.047,7.194],[0.034,7.232],[-0.016,7.301],[-0.1,7.348],[-0.194,7.341],[-0.216,7.363],[-0.209,7.369],[-0.219,7.385],[-0.244,7.391],[-0.325,7.348],[-0.372,7.301],[-0.397,7.263],[-0.422,7.188],[-0.428,6.007],[-0.472,5.976],[-0.465,5.764],[-0.428,5.657],[-0.434,5.651],[-0.428,5.532],[-0.434,5.489],[-0.428,5.483],[-0.434,5.476],[-0.434,4.233],[-0.45,4.217],[-0.531,4.192],[-0.587,4.161],[-0.6,4.167],[-0.612,4.155],[-0.644,4.155],[-0.731,4.124],[-0.781,4.067],[-0.834,4.033],[-0.859,3.977],[-0.89,3.946],[-0.903,3.908],[-0.925,3.886],[-1.006,3.842],[-1.043,3.836],[-1.325,3.917],[-1.368,3.917],[-1.4,3.905],[-1.562,3.767],[-1.721,3.608],[-1.834,3.471],[-1.852,3.427],[-1.852,3.383],[-1.771,3.083],[-1.89,2.852],[-2.002,2.515],[-2.046,2.24]],"front":[[-2.05,4.233],[-2.048,0],[0,0],[2.05,0.002],[2.048,4.235]]},"features":{"drum":{},"rear":{"window":[[[-0.187,3.921],[0.194,3.921],[0.194,2.79],[-0.187,2.79]]],"window_recess":[[[-0.281,3.983],[0.287,3.983],[0.287,2.733],[-0.281,2.733]]],"hub":[[[-0.687,2.702],[0.7,2.702],[0.7,1.309],[-0.687,1.309]]],"hub_button":[[[-0.187,2.202],[0.2,2.202],[0.2,1.809],[-0.187,1.809]]],"dot_matrix":[[[-0.662,1.134],[0.656,1.134],[0.656,0.665],[-0.662,0.665]]],"catch_block":[[[-0.469,5.995],[-0.419,5.995],[-0.419,5.701],[-0.469,5.701]]],"collar":[[[-0.431,4.539],[0.437,4.539],[0.437,4.489],[-0.431,4.489]]]},"front":{"lever_eye":[[[0.455,3.873],[-0.118,3.873],[-0.118,3.3],[0.455,3.3]]],"lever_hole":[[[0.371,3.788],[-0.034,3.788],[-0.034,3.384],[0.371,3.384]]],"lever_arm":[[[-0.051,3.822],[-0.219,3.832],[-0.387,3.822],[-0.556,3.795],[-0.724,3.748],[-0.893,3.67],[-1.044,3.586],[-0.893,3.613],[-0.724,3.654],[-0.556,3.681],[-0.387,3.687],[-0.219,3.681],[-0.067,3.637]]]}},"placement":{"drum":{"plane":"xy","offset":{}},"rear":{"plane":"zy","offset":{}},"front":{"plane":"zy","offset":{}}},"bounds":{"min":[-0.0422,-7.3609,-2.0439],"max":[3.9944,0,2.0439]},"volume_in3":51.6435,"centroid":[1.9194,-4.6445,-0.0017],"shell":[1.8932,-4.1792,-0.006],"area_in2":118.1015,"triangles":20172,"manifold":true,"slabs":[[0.64,-7.361,-1.681,2.483,-6.974,1.675],[0.571,-6.974,-1.859,3.735,-6.586,1.834],[0.511,-6.586,-1.859,3.993,-6.199,1.835],[0.437,-6.199,-1.976,3.994,-5.811,1.975],[0.369,-5.811,-2.04,3.981,-5.424,2.04],[0.302,-5.424,-2.044,3.946,-5.036,2.044],[0.23,-5.036,-2.027,3.878,-4.649,2.027],[0.16,-4.649,-1.935,3.81,-4.262,1.935],[0.094,-4.262,-1.852,3.741,-3.874,1.852],[0.058,-3.874,-1.852,3.661,-3.487,1.852],[-0.041,-3.487,-1.852,3.65,-3.099,1.852],[-0.042,-3.099,-1.572,3.582,-2.712,1.566],[0,-2.712,-0.438,2.536,-0.387,0.438],[0.104,-0.387,-0.438,2.528,0,0.438]],"slots":["body","window"]},"mas-defense-nero-12-62-handguard":{"part":"mas-defense-nero-12-62-handguard","model":"mas-defense-nero-12-62-handguard.glb","script":"mas_defense_nero_12_62_handguard.py","inputs":{"mas-defense-nero-12-62-handguard.bottom_below_bore":0.85,"mas-defense-nero-12-62-handguard.bottom_half_width":0.35,"mas-defense-nero-12-62-handguard.inside_diameter":1.25,"mas-defense-nero-12-62-handguard.length":12.84,"mas-defense-nero-12-62-handguard.lower0_from_rear_face":2.33,"mas-defense-nero-12-62-handguard.lower_bottom_below_bore":0.67,"mas-defense-nero-12-62-handguard.lower_count":14,"mas-defense-nero-12-62-handguard.lower_length":0.52,"mas-defense-nero-12-62-handguard.lower_pitch":0.69,"mas-defense-nero-12-62-handguard.lower_slant":24,"mas-defense-nero-12-62-handguard.lug_bottom_below_bore":1.08,"mas-defense-nero-12-62-handguard.lug_end_from_rear_face":1.48,"mas-defense-nero-12-62-handguard.lug_flat_end_from_rear_face":1.18,"mas-defense-nero-12-62-handguard.mlok_slot0_from_rear_face":4.01,"mas-defense-nero-12-62-handguard.mlok_slots":5,"mas-defense-nero-12-62-handguard.qd_diameter":0.37,"mas-defense-nero-12-62-handguard.qd_front_from_rear_face":11.92,"mas-defense-nero-12-62-handguard.qd_rear_from_rear_face":2.58,"mas-defense-nero-12-62-handguard.rail_neck_below_top":0.4,"mas-defense-nero-12-62-handguard.rail_slot0_from_rear_face":0.39,"mas-defense-nero-12-62-handguard.rail_slots":31,"mas-defense-nero-12-62-handguard.rail_top_above_bore":1.22,"mas-defense-nero-12-62-handguard.rail_underside_below_top":0.24,"mas-defense-nero-12-62-handguard.rear_x":-0.445,"mas-defense-nero-12-62-handguard.screw0_from_rear_face":0.34,"mas-defense-nero-12-62-handguard.screw_below_bore":0.93,"mas-defense-nero-12-62-handguard.screw_end_diameter":0.2,"mas-defense-nero-12-62-handguard.screw_head_diameter":0.26,"mas-defense-nero-12-62-handguard.screw_head_proud":0.06,"mas-defense-nero-12-62-handguard.screw_spacing":0.6,"mas-defense-nero-12-62-handguard.side_flat_bottom_below_bore":0.4,"mas-defense-nero-12-62-handguard.side_flat_top_above_bore":0.62,"mas-defense-nero-12-62-handguard.wall":0.06,"mas-defense-nero-12-62-handguard.width":1.6,"mas-defense-nero-12-62-handguard.window0_from_rear_face":3.1,"mas-defense-nero-12-62-handguard.window_bottom_above_bore":0.39,"mas-defense-nero-12-62-handguard.window_count":14,"mas-defense-nero-12-62-handguard.window_length":0.55,"mas-defense-nero-12-62-handguard.window_pitch":0.69,"mas-defense-nero-12-62-handguard.window_slant":30,"std.mlok.slot_corner_r":0.0937007874015748,"std.mlok.slot_length":1.2598425196850394,"std.mlok.slot_pitch":1.574803149606299,"std.mlok.slot_width":0.2755905511811024,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{"top":[[-0.475,-0.333],[-0.461,-0.387],[-0.388,-0.402],[-0.35,-0.776],[-0.304,-0.798],[1.783,-0.807],[1.836,-0.792],[1.973,-0.808],[2.089,-0.793],[3.34,-0.808],[3.393,-0.794],[4.707,-0.809],[4.76,-0.794],[6.58,-0.811],[6.633,-0.797],[6.706,-0.812],[6.76,-0.798],[7.694,-0.811],[7.747,-0.797],[7.82,-0.812],[8.073,-0.813],[8.127,-0.798],[9.314,-0.813],[9.367,-0.798],[9.44,-0.813],[9.693,-0.814],[9.747,-0.8],[10.934,-0.814],[10.987,-0.8],[11.25,-0.816],[11.367,-0.802],[11.999,-0.804],[12.072,-0.819],[12.126,-0.805],[12.238,-0.815],[12.267,-0.795],[12.265,-0.744],[12.341,-0.368],[12.361,-0.334],[12.42,-0.295],[12.432,-0.234],[12.434,0.209],[12.429,0.247],[12.371,0.335],[12.347,0.34],[12.318,0.384],[12.309,0.525],[12.26,0.662],[12.271,0.774],[12.249,0.791],[11.806,0.792],[11.753,0.778],[11.616,0.793],[11.3,0.794],[11.247,0.78],[9.174,0.798],[9.121,0.784],[9.048,0.799],[8.732,0.8],[8.678,0.786],[8.479,0.801],[8.362,0.787],[8.289,0.802],[8.172,0.788],[7.919,0.789],[7.846,0.803],[7.793,0.789],[4.708,0.811],[4.655,0.797],[4.519,0.812],[4.202,0.813],[4.149,0.799],[3.833,0.8],[3.76,0.815],[3.643,0.801],[0.179,0.825],[0.126,0.81],[-0.327,0.827],[-0.349,0.78],[-0.335,0.664],[-0.374,0.532],[-0.377,0.457],[-0.421,0.428],[-0.445,0.433],[-0.472,0.363]]},"features":{"top":{}},"placement":{"top":{"plane":"xz","offset":{}}},"bounds":{"min":[-0.445,-1.08,-0.8],"max":[12.395,1.22,0.8]},"volume_in3":5.68,"centroid":[4.416,0.2703,-0.0004],"shell":[5.6445,0.1465,-0.0005],"area_in2":126.7658,"triangles":35466,"manifold":true,"slabs":[[-0.445,-1.08,-0.8,1.111,1.22,0.8],[1.111,-0.85,-0.8,12.395,1.22,0.8]],"slots":["body","hardware"]},"mas-defense-nero-15-handguard":{"part":"mas-defense-nero-15-handguard","model":"mas-defense-nero-15-handguard.glb","script":"mas_defense_nero_15_handguard.py","inputs":{"mas-defense-nero-15-handguard.bottom_below_bore":0.85,"mas-defense-nero-15-handguard.bottom_half_width":0.35,"mas-defense-nero-15-handguard.inside_diameter":1.25,"mas-defense-nero-15-handguard.length":15.12,"mas-defense-nero-15-handguard.lower0_from_rear_face":2.05,"mas-defense-nero-15-handguard.lower_bottom_below_bore":0.67,"mas-defense-nero-15-handguard.lower_count":18,"mas-defense-nero-15-handguard.lower_length":0.52,"mas-defense-nero-15-handguard.lower_pitch":0.689,"mas-defense-nero-15-handguard.lower_slant":24,"mas-defense-nero-15-handguard.lug_bottom_below_bore":1.08,"mas-defense-nero-15-handguard.lug_end_from_rear_face":1.48,"mas-defense-nero-15-handguard.lug_flat_end_from_rear_face":1.18,"mas-defense-nero-15-handguard.mlok_slot0_from_rear_face":3.51,"mas-defense-nero-15-handguard.mlok_slots":7,"mas-defense-nero-15-handguard.qd_diameter":0.37,"mas-defense-nero-15-handguard.qd_front_from_rear_face":14.3,"mas-defense-nero-15-handguard.qd_rear_from_rear_face":2.27,"mas-defense-nero-15-handguard.rail_neck_below_top":0.4,"mas-defense-nero-15-handguard.rail_slot0_from_rear_face":0.35,"mas-defense-nero-15-handguard.rail_slots":37,"mas-defense-nero-15-handguard.rail_top_above_bore":1.22,"mas-defense-nero-15-handguard.rail_underside_below_top":0.24,"mas-defense-nero-15-handguard.rear_x":-0.445,"mas-defense-nero-15-handguard.screw0_from_rear_face":0.34,"mas-defense-nero-15-handguard.screw_below_bore":0.93,"mas-defense-nero-15-handguard.screw_end_diameter":0.2,"mas-defense-nero-15-handguard.screw_head_diameter":0.26,"mas-defense-nero-15-handguard.screw_head_proud":0.06,"mas-defense-nero-15-handguard.screw_spacing":0.6,"mas-defense-nero-15-handguard.side_flat_bottom_below_bore":0.4,"mas-defense-nero-15-handguard.side_flat_top_above_bore":0.62,"mas-defense-nero-15-handguard.wall":0.06,"mas-defense-nero-15-handguard.width":1.6,"mas-defense-nero-15-handguard.window0_from_rear_face":2.82,"mas-defense-nero-15-handguard.window_bottom_above_bore":0.39,"mas-defense-nero-15-handguard.window_count":18,"mas-defense-nero-15-handguard.window_length":0.55,"mas-defense-nero-15-handguard.window_pitch":0.688,"mas-defense-nero-15-handguard.window_slant":30,"std.mlok.slot_corner_r":0.0937007874015748,"std.mlok.slot_length":1.2598425196850394,"std.mlok.slot_pitch":1.574803149606299,"std.mlok.slot_width":0.2755905511811024,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{"side":[[-0.447,1.173],[-0.447,-1.043],[-0.432,-1.058],[-0.373,-0.999],[-0.284,-1.088],[0.721,-1.088],[0.809,-1.029],[0.839,-1.029],[1.016,-0.851],[3.616,-0.851],[3.646,-0.822],[3.823,-0.822],[3.853,-0.851],[4,-0.851],[4.03,-0.822],[4.06,-0.851],[4.887,-0.851],[4.916,-0.822],[4.946,-0.851],[5.271,-0.851],[5.301,-0.822],[5.33,-0.851],[5.36,-0.851],[5.389,-0.822],[6.246,-0.822],[6.276,-0.851],[6.305,-0.822],[14.254,-0.822],[14.283,-0.851],[14.638,-0.851],[14.653,-0.836],[14.653,-0.718],[14.682,-0.689],[14.682,-0.63],[14.712,-0.6],[14.712,-0.511],[14.741,-0.482],[14.741,-0.364],[14.771,-0.334],[14.771,0.198],[14.801,0.227],[14.771,0.257],[14.801,0.286],[14.801,0.316],[14.741,0.375],[14.741,0.552],[14.712,0.582],[14.712,0.67],[14.682,0.7],[14.682,1.232],[14.668,1.247],[14.136,1.247],[14.121,1.232],[14.121,1.143],[14.077,1.128],[14.062,1.143],[14.062,1.202],[14.017,1.247],[13.752,1.247],[13.737,1.232],[13.737,1.173],[13.692,1.128],[13.663,1.128],[13.648,1.143],[13.648,1.232],[13.633,1.247],[13.367,1.247],[13.323,1.202],[13.323,1.143],[13.279,1.128],[13.234,1.173],[13.234,1.232],[13.22,1.247],[12.954,1.247],[12.939,1.232],[12.939,1.143],[12.924,1.128],[12.865,1.128],[12.85,1.143],[12.85,1.232],[12.836,1.247],[12.57,1.247],[12.555,1.232],[12.555,1.173],[12.511,1.128],[12.481,1.128],[12.437,1.173],[12.437,1.232],[12.422,1.247],[12.185,1.247],[12.141,1.202],[12.141,1.143],[12.126,1.128],[12.067,1.128],[12.052,1.143],[12.052,1.202],[12.008,1.247],[11.772,1.247],[11.757,1.232],[11.757,1.143],[11.742,1.128],[11.654,1.128],[11.639,1.143],[11.639,1.232],[11.624,1.247],[11.388,1.247],[11.373,1.232],[11.373,1.173],[11.343,1.143],[11.329,1.128],[11.269,1.128],[11.225,1.173],[11.225,1.232],[11.21,1.247],[11.004,1.247],[10.959,1.202],[10.959,1.143],[10.944,1.128],[10.856,1.128],[10.841,1.143],[10.841,1.232],[10.826,1.247],[10.619,1.247],[10.575,1.202],[10.575,1.143],[10.531,1.099],[10.501,1.128],[10.442,1.128],[10.427,1.143],[10.427,1.232],[10.413,1.247],[10.206,1.247],[10.191,1.232],[10.191,1.143],[10.147,1.099],[10.117,1.128],[10.058,1.128],[10.043,1.143],[10.043,1.202],[9.999,1.247],[9.822,1.247],[9.777,1.202],[9.777,1.114],[9.762,1.099],[9.674,1.099],[9.629,1.143],[9.629,1.232],[9.615,1.247],[9.437,1.247],[9.393,1.202],[9.393,1.143],[9.349,1.099],[9.26,1.099],[9.245,1.114],[9.245,1.202],[9.201,1.247],[9.171,1.247],[9.142,1.217],[9.024,1.217],[9.009,1.202],[9.009,1.143],[8.965,1.099],[8.876,1.099],[8.832,1.143],[8.832,1.232],[8.787,1.247],[8.758,1.217],[8.64,1.217],[8.595,1.173],[8.595,1.114],[8.581,1.099],[8.462,1.099],[8.448,1.114],[8.448,1.202],[8.433,1.217],[8.226,1.217],[8.211,1.202],[8.211,1.114],[8.196,1.099],[8.078,1.099],[8.034,1.143],[8.034,1.202],[8.019,1.217],[7.842,1.217],[7.827,1.202],[7.827,1.114],[7.812,1.099],[7.665,1.099],[7.65,1.114],[7.65,1.202],[7.635,1.217],[7.458,1.217],[7.443,1.202],[7.443,1.143],[7.399,1.099],[7.251,1.099],[7.236,1.114],[7.236,1.202],[7.221,1.217],[7.074,1.217],[7.029,1.173],[7.059,1.143],[7.014,1.099],[6.867,1.099],[6.822,1.143],[6.852,1.173],[6.837,1.217],[6.66,1.217],[6.645,1.202],[6.645,1.114],[6.63,1.099],[6.453,1.099],[6.438,1.114],[6.438,1.202],[6.423,1.217],[6.276,1.217],[6.261,1.202],[6.261,1.114],[6.246,1.099],[6.069,1.099],[6.054,1.114],[6.054,1.202],[6.039,1.217],[5.892,1.217],[5.877,1.202],[5.877,1.114],[5.862,1.099],[5.655,1.099],[5.64,1.114],[5.64,1.202],[5.626,1.217],[5.478,1.217],[5.463,1.173],[5.493,1.143],[5.448,1.099],[5.271,1.099],[5.256,1.114],[5.256,1.202],[5.242,1.217],[5.094,1.217],[5.079,1.202],[5.079,1.114],[5.064,1.099],[4.887,1.099],[4.872,1.114],[4.872,1.202],[4.857,1.217],[4.71,1.217],[4.665,1.173],[4.695,1.143],[4.651,1.099],[4.503,1.099],[4.488,1.114],[4.488,1.202],[4.473,1.217],[4.296,1.217],[4.281,1.202],[4.281,1.114],[4.266,1.099],[4.119,1.099],[4.104,1.114],[4.104,1.173],[4.06,1.217],[3.912,1.217],[3.897,1.202],[3.897,1.114],[3.882,1.099],[3.735,1.099],[3.72,1.114],[3.72,1.173],[3.675,1.217],[3.498,1.217],[3.483,1.202],[3.483,1.114],[3.469,1.099],[3.321,1.099],[3.306,1.114],[3.306,1.202],[3.291,1.217],[3.114,1.217],[3.099,1.202],[3.099,1.114],[3.084,1.099],[2.937,1.099],[2.922,1.114],[2.922,1.202],[2.907,1.217],[2.73,1.217],[2.715,1.202],[2.715,1.143],[2.671,1.099],[2.553,1.099],[2.538,1.114],[2.538,1.202],[2.523,1.217],[2.346,1.217],[2.301,1.173],[2.301,1.114],[2.287,1.099],[2.228,1.099],[2.198,1.069],[2.154,1.114],[2.154,1.202],[2.139,1.217],[1.932,1.217],[1.917,1.202],[1.917,1.114],[1.902,1.099],[1.784,1.099],[1.77,1.114],[1.77,1.173],[1.725,1.217],[1.548,1.217],[1.533,1.202],[1.533,1.114],[1.489,1.069],[1.43,1.069],[1.385,1.114],[1.385,1.173],[1.341,1.217],[1.312,1.217],[1.282,1.188],[1.193,1.188],[1.164,1.217],[1.119,1.173],[1.119,1.114],[1.075,1.069],[1.046,1.069],[1.001,1.114],[1.001,1.173],[0.957,1.217],[0.927,1.217],[0.898,1.188],[0.809,1.188],[0.78,1.217],[0.735,1.173],[0.735,1.114],[0.691,1.069],[0.661,1.069],[0.617,1.114],[0.617,1.173],[0.573,1.217],[0.543,1.217],[0.514,1.188],[0.366,1.188],[0.351,1.173],[0.351,1.114],[0.307,1.069],[0.248,1.069],[0.233,1.084],[0.233,1.173],[0.189,1.217],[0.159,1.217],[0.13,1.188],[-0.018,1.188],[-0.062,1.143],[-0.062,1.084],[-0.077,1.069],[-0.136,1.069],[-0.151,1.084],[-0.151,1.173],[-0.166,1.188],[-0.432,1.188]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{}}},"bounds":{"min":[-0.445,-1.08,-0.8],"max":[14.675,1.22,0.8]},"volume_in3":6.2448,"centroid":[5.4128,0.2834,-0.0003],"shell":[6.7612,0.1486,-0.0004],"area_in2":143.9232,"triangles":44072,"manifold":true,"slabs":[[-0.445,-1.08,-0.8,1.147,1.22,0.8],[1.147,-0.85,-0.8,14.675,1.22,0.8]],"slots":["body","hardware"]},"mas-defense-nero-9-87-handguard":{"part":"mas-defense-nero-9-87-handguard","model":"mas-defense-nero-9-87-handguard.glb","script":"mas_defense_nero_9_87_handguard.py","inputs":{"mas-defense-nero-9-87-handguard.bottom_below_bore":0.85,"mas-defense-nero-9-87-handguard.bottom_half_width":0.35,"mas-defense-nero-9-87-handguard.inside_diameter":1.25,"mas-defense-nero-9-87-handguard.length":10.01,"mas-defense-nero-9-87-handguard.lower0_from_rear_face":2.41,"mas-defense-nero-9-87-handguard.lower_bottom_below_bore":0.67,"mas-defense-nero-9-87-handguard.lower_count":10,"mas-defense-nero-9-87-handguard.lower_length":0.52,"mas-defense-nero-9-87-handguard.lower_pitch":0.682,"mas-defense-nero-9-87-handguard.lower_slant":24,"mas-defense-nero-9-87-handguard.lug_bottom_below_bore":1.08,"mas-defense-nero-9-87-handguard.lug_end_from_rear_face":1.48,"mas-defense-nero-9-87-handguard.lug_flat_end_from_rear_face":1.18,"mas-defense-nero-9-87-handguard.mlok_slot0_from_rear_face":3.89,"mas-defense-nero-9-87-handguard.mlok_slots":4,"mas-defense-nero-9-87-handguard.qd_diameter":0.37,"mas-defense-nero-9-87-handguard.qd_rear_from_rear_face":2.69,"mas-defense-nero-9-87-handguard.rail_neck_below_top":0.4,"mas-defense-nero-9-87-handguard.rail_slot0_from_rear_face":0.36,"mas-defense-nero-9-87-handguard.rail_slots":24,"mas-defense-nero-9-87-handguard.rail_top_above_bore":1.22,"mas-defense-nero-9-87-handguard.rail_underside_below_top":0.24,"mas-defense-nero-9-87-handguard.rear_x":-0.445,"mas-defense-nero-9-87-handguard.screw0_from_rear_face":0.34,"mas-defense-nero-9-87-handguard.screw_below_bore":0.93,"mas-defense-nero-9-87-handguard.screw_end_diameter":0.2,"mas-defense-nero-9-87-handguard.screw_head_diameter":0.26,"mas-defense-nero-9-87-handguard.screw_head_proud":0.06,"mas-defense-nero-9-87-handguard.screw_spacing":0.6,"mas-defense-nero-9-87-handguard.side_flat_bottom_below_bore":0.4,"mas-defense-nero-9-87-handguard.side_flat_top_above_bore":0.62,"mas-defense-nero-9-87-handguard.wall":0.06,"mas-defense-nero-9-87-handguard.width":1.6,"mas-defense-nero-9-87-handguard.window0_from_rear_face":3.21,"mas-defense-nero-9-87-handguard.window_bottom_above_bore":0.39,"mas-defense-nero-9-87-handguard.window_count":10,"mas-defense-nero-9-87-handguard.window_length":0.55,"mas-defense-nero-9-87-handguard.window_pitch":0.68,"mas-defense-nero-9-87-handguard.window_slant":30,"std.mlok.slot_corner_r":0.0937007874015748,"std.mlok.slot_length":1.2598425196850394,"std.mlok.slot_pitch":1.574803149606299,"std.mlok.slot_width":0.2755905511811024,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{"top":[[-0.474,-0.06],[-0.465,-0.348],[-0.446,-0.377],[-0.45,-0.401],[-0.363,-0.405],[-0.344,-0.433],[-0.328,-0.549],[-0.308,-0.577],[-0.307,-0.64],[-0.288,-0.669],[-0.286,-0.794],[-0.264,-0.81],[-0.125,-0.799],[-0.052,-0.812],[0.073,-0.811],[0.125,-0.796],[0.198,-0.809],[0.251,-0.794],[0.535,-0.81],[1.175,-0.792],[1.247,-0.806],[1.512,-0.793],[1.584,-0.806],[1.637,-0.791],[1.709,-0.804],[2.162,-0.789],[2.234,-0.803],[2.686,-0.787],[2.759,-0.801],[3.611,-0.785],[3.683,-0.799],[3.948,-0.786],[4.02,-0.799],[4.073,-0.784],[4.145,-0.798],[4.41,-0.785],[4.482,-0.798],[4.809,-0.784],[4.882,-0.798],[4.934,-0.783],[5.007,-0.796],[5.334,-0.783],[5.406,-0.796],[5.459,-0.781],[5.531,-0.794],[5.584,-0.779],[5.657,-0.793],[5.921,-0.78],[5.994,-0.793],[6.046,-0.778],[6.119,-0.792],[6.446,-0.778],[6.518,-0.792],[6.908,-0.777],[6.98,-0.791],[7.433,-0.775],[7.505,-0.789],[7.62,-0.773],[7.693,-0.786],[8.882,-0.771],[8.954,-0.785],[9.093,-0.773],[9.166,-0.787],[9.416,-0.784],[9.43,-0.774],[9.442,-0.714],[9.432,-0.699],[9.457,-0.629],[9.502,-0.325],[9.573,-0.276],[9.594,-0.23],[9.582,-0.028],[9.598,0.256],[9.577,0.347],[9.48,0.428],[9.469,0.567],[9.429,0.687],[9.432,0.774],[9.413,0.802],[9.352,0.814],[9.3,0.799],[9.227,0.812],[8.501,0.798],[8.428,0.812],[8.313,0.796],[8.115,0.808],[8.063,0.793],[7.904,0.81],[7.851,0.795],[7.653,0.807],[7.601,0.791],[7.528,0.805],[7.264,0.792],[7.191,0.806],[6.614,0.789],[6.541,0.802],[6.277,0.789],[6.204,0.803],[5.016,0.788],[4.943,0.801],[4.303,0.783],[4.231,0.797],[4.029,0.785],[3.956,0.798],[3.504,0.783],[3.432,0.796],[3.379,0.781],[3.306,0.795],[2.854,0.779],[2.782,0.793],[2.517,0.78],[2.445,0.793],[2.392,0.778],[2.32,0.792],[1.068,0.776],[0.996,0.789],[0.081,0.773],[0.009,0.787],[-0.193,0.774],[-0.265,0.788],[-0.286,0.742],[-0.268,0.639],[-0.333,0.426],[-0.362,0.406],[-0.434,0.42],[-0.457,0.362],[-0.471,0.152],[-0.46,0.013]]},"features":{"top":{}},"placement":{"top":{"plane":"xz","offset":{}}},"bounds":{"min":[-0.445,-1.08,-0.8],"max":[9.565,1.22,0.8]},"volume_in3":4.7975,"centroid":[3.1373,0.2538,-0.0004],"shell":[4.217,0.1476,-0.0006],"area_in2":101.3255,"triangles":26508,"manifold":true,"slabs":[[-0.445,-1.08,-0.8,1.095,1.22,0.8],[1.095,-0.85,-0.8,9.565,1.22,0.8]],"slots":["body","hardware"]},"mft-battlelink-minimalist-stock":{"part":"mft-battlelink-minimalist-stock","model":"mft-battlelink-minimalist-stock.glb","script":"mft_battlelink_minimalist_stock.py","inputs":{"bcm-receiver-extension.tube_front_behind_pin":0.669,"bcm-receiver-extension.tube_length":7.25,"mft-battlelink-minimalist-stock.block_width":0.63,"mft-battlelink-minimalist-stock.butt_behind_pin_pos1":9.009,"mft-battlelink-minimalist-stock.cross_pin_diameter":0.11,"mft-battlelink-minimalist-stock.cross_pin_length":1.08,"mft-battlelink-minimalist-stock.frame_width":0.47,"mft-battlelink-minimalist-stock.lock_pin_ahead_of_butt":4.83,"mft-battlelink-minimalist-stock.lock_pin_diameter":0.234,"mft-battlelink-minimalist-stock.neck_width":0.67,"mft-battlelink-minimalist-stock.pad_width_low":1.42,"mft-battlelink-minimalist-stock.pad_width_low_below_top":3,"mft-battlelink-minimalist-stock.pad_width_toe":1.2,"mft-battlelink-minimalist-stock.pivot_pin_diameter":0.148,"mft-battlelink-minimalist-stock.qd_bore_diameter":0.365,"mft-battlelink-minimalist-stock.qd_rim_diameter":0.424,"mft-battlelink-minimalist-stock.rail_channel_floor_below_axis":0.885,"mft-battlelink-minimalist-stock.rear_wall_top_below_top":0.89,"mft-battlelink-minimalist-stock.spring_wire_diameter":0.035,"mft-battlelink-minimalist-stock.top_hole_diameter":0.39,"mft-battlelink-minimalist-stock.tube_axis_below_top":0.66,"mft-battlelink-minimalist-stock.web_thickness":0.25,"mft-battlelink-minimalist-stock.width":1.752,"std.receiver_extension.milspec_od":1.148,"std.receiver_extension.rail_bottom_below_axis":0.874,"std.receiver_extension.rail_width":0.49},"profiles":{"side":[[0,-0.616],[0,-0.861],[0.032,-1.226],[0.048,-1.251],[0.085,-1.256],[0.115,-1.281],[0.129,-1.383],[0.125,-1.42],[0.06,-1.457],[0.074,-1.609],[0.09,-1.648],[0.141,-1.658],[0.162,-1.678],[0.171,-1.738],[0.171,-1.812],[0.106,-1.854],[0.125,-2.011],[0.141,-2.041],[0.208,-2.066],[0.222,-2.149],[0.222,-2.214],[0.162,-2.26],[0.175,-2.375],[0.189,-2.435],[0.205,-2.452],[0.252,-2.461],[0.272,-2.509],[0.277,-2.606],[0.261,-2.632],[0.217,-2.652],[0.212,-2.708],[0.379,-4.107],[0.406,-4.255],[0.462,-4.407],[0.547,-4.437],[0.577,-4.485],[0.591,-4.536],[0.554,-4.587],[0.554,-4.61],[0.628,-4.767],[0.649,-4.783],[0.713,-4.797],[0.753,-4.864],[0.753,-4.901],[0.716,-4.961],[0.785,-5.123],[0.824,-5.153],[0.866,-5.162],[1.23,-5.18],[1.272,-5.166],[1.309,-5.134],[1.614,-5.125],[1.674,-5.111],[1.701,-5.097],[1.741,-5.049],[1.801,-4.919],[1.791,-4.859],[1.653,-4.555],[1.404,-3.936],[1.279,-2.763],[1.325,-2.579],[1.385,-2.482],[1.443,-2.419],[1.563,-2.35],[1.688,-2.322],[2.999,-2.309],[3.029,-2.288],[3.043,-2.255],[2.95,-2.126],[2.932,-2.075],[2.936,-1.96],[2.957,-1.935],[2.985,-1.925],[3.096,-1.93],[3.13,-1.951],[3.103,-2.214],[3.103,-2.251],[3.128,-2.276],[3.156,-2.276],[3.216,-2.248],[3.322,-2.258],[3.391,-2.23],[3.511,-2.248],[3.553,-2.23],[3.613,-2.23],[3.673,-2.253],[3.756,-2.239],[3.807,-2.248],[3.848,-2.272],[3.959,-2.267],[4.051,-2.313],[5.912,-2.322],[6.037,-2.304],[6.166,-2.244],[6.261,-2.163],[6.445,-1.872],[6.54,-1.773],[6.605,-1.727],[6.757,-1.667],[7.043,-1.662],[7.069,-1.641],[7.082,-1.226],[7.138,-0.704],[7.138,-0.57],[7.096,-0.108],[7.071,-0.065],[7.029,-0.051],[6.78,-0.005],[5.035,0],[4.906,-0.023],[4.772,-0.023],[4.633,0],[4.527,0],[0.436,-0.028],[0.178,-0.046],[0.132,-0.065],[0.088,-0.108],[0.037,-0.229],[0.014,-0.381]],"front":[[-0.809,-0.624],[-0.809,-0.651],[-0.763,-0.742],[-0.443,-1.235],[-0.34,-1.342],[-0.34,-1.601],[-0.311,-1.63],[0.311,-1.63],[0.34,-1.601],[0.34,-1.342],[0.443,-1.235],[0.458,-1.212],[0.783,-0.712],[0.809,-0.651],[0.809,-0.624],[0.767,-0.536],[0.721,-0.464],[0.5,-0.181],[0.414,-0.103],[0.391,-0.088],[0.185,-0.019],[0.162,0],[-0.002,0],[-0.162,0],[-0.185,-0.019],[-0.399,-0.092],[-0.5,-0.181],[-0.733,-0.479],[-0.794,-0.59]]},"features":{"side":{"through":[[[5.91,-2.071],[5.919,-1.798],[5.963,-1.768],[6.212,-1.773],[6.238,-1.808],[6.233,-1.84],[6.127,-2.015],[6.051,-2.087],[5.972,-2.119],[5.935,-2.115]],[[1.505,-2.001],[1.535,-1.958],[1.591,-1.935],[2.699,-1.93],[2.726,-1.944],[2.761,-1.992],[2.766,-2.057],[2.756,-2.075],[2.699,-2.124],[2.569,-2.133],[1.581,-2.128],[1.54,-2.105],[1.51,-2.066]],[[0.873,-2.703],[0.896,-2.634],[0.953,-2.604],[1.004,-2.618],[1.039,-2.657],[1.062,-2.768],[1.173,-3.797],[1.129,-3.86],[1.097,-3.869],[1.037,-3.851],[1.007,-3.821],[0.993,-3.793],[0.97,-3.622]],[[1.071,-4.121],[1.085,-4.093],[1.129,-4.063],[1.198,-4.072],[1.251,-4.135],[1.417,-4.545],[1.408,-4.592],[1.369,-4.622],[1.318,-4.617],[1.279,-4.582],[1.076,-4.181]],[[1.394,-4.864],[1.406,-4.852],[1.595,-4.857],[1.634,-4.892],[1.653,-4.933],[1.637,-4.963],[1.609,-4.968],[1.447,-4.968]]],"buttpad":[[[-0.03,0.076],[0.339,0.076],[0.339,-0.478],[0.353,-1.17],[0.386,-1.632],[0.441,-2.094],[0.515,-2.556],[0.584,-3.017],[0.616,-3.479],[0.663,-3.941],[0.695,-4.171],[0.732,-4.402],[0.824,-4.633],[0.94,-4.864],[1.055,-5.095],[1.11,-5.256],[-0.03,-5.256]]],"plate":[[[0.386,-1.632],[0.441,-2.094],[0.515,-2.556],[0.584,-3.017],[0.616,-3.479],[0.663,-3.941],[0.695,-4.171],[0.732,-4.402],[0.824,-4.633],[0.94,-4.864],[1.055,-5.095],[1.11,-5.256],[1.24,-5.256],[1.18,-5.095],[1.064,-4.864],[0.949,-4.633],[0.847,-4.402],[0.81,-4.171],[0.778,-3.941],[0.732,-3.479],[0.699,-3.017],[0.63,-2.556],[0.556,-2.094],[0.501,-1.632]]],"housing":[[[0.247,0.076],[7.219,0.076],[7.219,-1.632],[0.247,-1.632]]],"rear":[[[0.247,0.076],[3.479,0.076],[3.479,-0.663],[3.225,-1.17],[3.202,-1.378],[0.247,-1.378]]],"lever":[[[3.918,-1.434],[4.633,-1.378],[4.979,-1.392],[5.012,-1.424],[5.012,-1.531],[4.633,-1.567],[4.125,-2.223],[4.125,-2.371],[3.11,-2.371],[3.11,-1.946],[3.839,-1.817],[3.885,-1.54]]],"block":[[[4.125,-1.632],[7.219,-1.632],[7.219,-2.371],[4.125,-2.371]]],"frame":[[[0.247,-1.632],[4.125,-1.632],[4.125,-5.256],[0.247,-5.256]]],"window":[[[4.772,-1.632],[4.901,-1.632],[4.901,-1.965],[4.772,-1.965]]],"crosspin":[[[4.776,-1.535],[4.887,-1.535],[4.887,-1.646],[4.776,-1.646]]],"pivot":[[[3.945,-1.484],[4.093,-1.484],[4.093,-1.632],[3.945,-1.632]]],"qd":[[[5.233,-1.655],[5.815,-1.655],[5.815,-2.311],[5.233,-2.311]]],"pockets":[[[0.672,-1.692],[1.267,-1.692],[1.147,-1.817],[1.009,-1.955],[0.893,-2.094],[0.801,-2.218],[0.723,-2.334],[0.672,-2.334]],[[1.54,-1.715],[2.906,-1.715],[2.754,-2.223],[1.041,-2.223],[1.101,-2.117],[1.207,-1.965],[1.355,-1.817]],[[0.824,-2.556],[1.147,-2.556],[1.217,-2.671],[1.286,-3.802],[1.217,-3.941],[1.055,-3.978],[0.94,-3.918],[0.87,-3.479],[0.764,-2.694]],[[0.963,-4.01],[1.18,-3.996],[1.263,-4.056],[1.54,-4.587],[1.517,-4.67],[1.401,-4.689],[1.309,-4.633],[1.009,-4.171]]],"bar":[[[4.125,-2.218],[5.926,-2.218],[5.926,-2.311],[4.125,-2.311]]],"blockpocket":[[[4.601,-1.655],[5.233,-1.655],[5.233,-2.218],[4.601,-2.218]]],"cells":[[[0.478,-1.184],[0.552,-1.184],[0.552,-1.295],[0.478,-1.295]],[[0.838,-1.184],[1.032,-1.184],[1.032,-1.295],[0.838,-1.295]],[[1.724,-1.184],[1.909,-1.184],[1.909,-1.295],[1.724,-1.295]],[[2.616,-1.184],[2.8,-1.184],[2.8,-1.295],[2.616,-1.295]]]},"front":{"opening":[[[-0.032,-0.071],[-0.269,-0.128],[-0.357,-0.185],[-0.414,-0.242],[-0.468,-0.3],[-0.513,-0.357],[-0.555,-0.414],[-0.597,-0.471],[-0.632,-0.529],[-0.678,-0.586],[-0.7,-0.643],[-0.67,-0.7],[-0.628,-0.758],[-0.594,-0.815],[-0.552,-0.872],[-0.513,-0.93],[-0.471,-0.987],[-0.41,-1.044],[-0.357,-1.101],[-0.303,-1.159],[-0.261,-1.216],[-0.242,-1.273],[-0.239,-1.33],[-0.239,-1.544],[0.239,-1.544],[0.239,-1.33],[0.242,-1.273],[0.261,-1.216],[0.303,-1.159],[0.357,-1.101],[0.41,-1.044],[0.471,-0.987],[0.513,-0.93],[0.552,-0.872],[0.594,-0.815],[0.628,-0.758],[0.67,-0.7],[0.7,-0.643],[0.678,-0.586],[0.632,-0.529],[0.597,-0.471],[0.555,-0.414],[0.513,-0.357],[0.468,-0.3],[0.414,-0.242],[0.357,-0.185],[0.269,-0.128],[0.032,-0.071]]]}},"placement":{"side":{"plane":"xy","offset":{"y":"tube_axis_below_top"}},"front":{"plane":"zy","offset":{"y":"tube_axis_below_top"}}},"bounds":{"min":[0,-4.52,-0.876],"max":[7.138,0.66,0.876]},"volume_in3":10.7685,"centroid":[2.265,-1.0306,0.0001],"shell":[2.8359,-0.9879,0.0001],"area_in2":123.6181,"triangles":16886,"manifold":true,"slabs":[[0,-3.543,-0.876,0.397,0.629,0.876],[0.397,-4.52,-0.876,1.586,0.64,0.876],[1.586,-4.466,-0.876,1.983,0.643,0.876],[1.983,-1.659,-0.876,3.172,0.651,0.876],[3.172,-1.608,-0.876,3.569,0.653,0.876],[3.569,-1.665,-0.809,6.345,0.66,0.809],[6.345,-1.37,-0.809,6.741,0.656,0.809],[6.741,-1.013,-0.809,7.138,0.655,0.809]],"slots":["body","buttpad","qd","hardware"]},"midwest-combat-rail-15-handguard":{"part":"midwest-combat-rail-15-handguard","model":"midwest-combat-rail-15-handguard.glb","script":"midwest_combat_rail_15_handguard.py","inputs":{"midwest-combat-rail-15-handguard.body_bottom_below_bore":0.75,"midwest-combat-rail-15-handguard.channel_roof_below_top":0.15,"midwest-combat-rail-15-handguard.clamp_gap_width":0.08,"midwest-combat-rail-15-handguard.corner_chamfer_height":0.106,"midwest-combat-rail-15-handguard.diag_face_distance":0.75,"midwest-combat-rail-15-handguard.hole0_from_rail_slot0":1.576,"midwest-combat-rail-15-handguard.hole_center_below_top":0.36,"midwest-combat-rail-15-handguard.hole_count":32,"midwest-combat-rail-15-handguard.hole_d":0.24,"midwest-combat-rail-15-handguard.inside_diameter":1.3,"midwest-combat-rail-15-handguard.length":15,"midwest-combat-rail-15-handguard.lug_bottom_below_bore":1.135,"midwest-combat-rail-15-handguard.lug_corner_r":0.13,"midwest-combat-rail-15-handguard.lug_flat_from_rear":1.24,"midwest-combat-rail-15-handguard.lug_ramp_from_rear":1.64,"midwest-combat-rail-15-handguard.lug_width":0.51,"midwest-combat-rail-15-handguard.mlok_bottom_slots":7,"midwest-combat-rail-15-handguard.mlok_diag_slot0_x":2.21,"midwest-combat-rail-15-handguard.mlok_diag_slots":8,"midwest-combat-rail-15-handguard.mlok_lower_row_below_bore":0.5,"midwest-combat-rail-15-handguard.mlok_side_slot0_x":3.785,"midwest-combat-rail-15-handguard.mlok_side_slots":7,"midwest-combat-rail-15-handguard.mlok_upper_row_above_bore":0.51,"midwest-combat-rail-15-handguard.neck_base_above_bore":0.664,"midwest-combat-rail-15-handguard.neck_wall":0.06,"midwest-combat-rail-15-handguard.neck_width":0.69,"midwest-combat-rail-15-handguard.nose_bottom_run":0.48,"midwest-combat-rail-15-handguard.nut_bore":1.244,"midwest-combat-rail-15-handguard.nut_length":1.12,"midwest-combat-rail-15-handguard.nut_od":1.345,"midwest-combat-rail-15-handguard.plate_height":0.36,"midwest-combat-rail-15-handguard.plate_length":1,"midwest-combat-rail-15-handguard.plate_thickness":0.06,"midwest-combat-rail-15-handguard.pocket_depth":0.02,"midwest-combat-rail-15-handguard.pocket_diag_from_rear":1.1,"midwest-combat-rail-15-handguard.pocket_diag_length":1.27,"midwest-combat-rail-15-handguard.pocket_diag_width":0.33,"midwest-combat-rail-15-handguard.pocket_side_from_rear":0.815,"midwest-combat-rail-15-handguard.pocket_side_length":0.7,"midwest-combat-rail-15-handguard.pocket_side_width":0.28,"midwest-combat-rail-15-handguard.rail_front_from_last_slot":0.5,"midwest-combat-rail-15-handguard.rail_length":14.91,"midwest-combat-rail-15-handguard.rail_slot0_x":0.175,"midwest-combat-rail-15-handguard.rail_slots":36,"midwest-combat-rail-15-handguard.rail_top_above_bore":1.22,"midwest-combat-rail-15-handguard.rear_face_x":-0.445,"midwest-combat-rail-15-handguard.rear_x":-0.61,"midwest-combat-rail-15-handguard.scallop_count":16,"midwest-combat-rail-15-handguard.scallop_height":0.03,"midwest-combat-rail-15-handguard.scallop_length":0.22,"midwest-combat-rail-15-handguard.screw_below_bore":0.887,"midwest-combat-rail-15-handguard.screw_d":0.19,"midwest-combat-rail-15-handguard.screw_front_from_rear":0.985,"midwest-combat-rail-15-handguard.screw_head_d":0.31,"midwest-combat-rail-15-handguard.screw_head_height":0.17,"midwest-combat-rail-15-handguard.screw_length":0.5,"midwest-combat-rail-15-handguard.screw_rear_from_rear":0.427,"midwest-combat-rail-15-handguard.screw_socket_w":0.155,"midwest-combat-rail-15-handguard.short_slot_length":0.64,"midwest-combat-rail-15-handguard.side_flat_height":0.478,"midwest-combat-rail-15-handguard.socket_d":0.365,"midwest-combat-rail-15-handguard.socket_from_rear":1.9,"midwest-combat-rail-15-handguard.socket_recess_depth":0.035,"midwest-combat-rail-15-handguard.socket_recess_length":0.62,"midwest-combat-rail-15-handguard.tab_gap":0.638,"midwest-combat-rail-15-handguard.tab_length":0.165,"midwest-combat-rail-15-handguard.width":1.5,"std.mlok.slot_corner_r":0.0937007874015748,"std.mlok.slot_length":1.2598425196850394,"std.mlok.slot_pitch":1.574803149606299,"std.mlok.slot_width":0.2755905511811024,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{},"features":{},"placement":{},"bounds":{"min":[-0.61,-1.135,-0.75],"max":[14.555,1.22,0.75]},"volume_in3":5.8177,"centroid":[6.1931,0.168,0.0013],"shell":[6.27,0.2278,0.0014],"area_in2":164.4196,"triangles":47348,"manifold":true,"slabs":[[-0.61,-1.135,-0.75,0.986,1.22,0.75],[0.986,-0.951,-0.75,1.385,1.22,0.75],[1.385,-0.75,-0.75,14.156,1.22,0.75],[14.156,-0.676,-0.75,14.555,1.22,0.75]],"slots":["body","hardware"]},"midwest-industries-drop-in-mlok-carbine":{"part":"midwest-industries-drop-in-mlok-carbine","model":"midwest-industries-drop-in-mlok-carbine.glb","script":"midwest_industries_drop_in_mlok_carbine.py","inputs":{"bcm-front-sight-base-f-750.port_from_rear":0.27,"bcm-front-sight-base-f-750.ring_r":0.44,"midwest-industries-drop-in-mlok-carbine.base_rear_x":6.868,"midwest-industries-drop-in-mlok-carbine.bevel_hole0_from_slot0":0.373,"midwest-industries-drop-in-mlok-carbine.bevel_hole_d":0.6,"midwest-industries-drop-in-mlok-carbine.bevel_holes":8,"midwest-industries-drop-in-mlok-carbine.big_hole_below_top":0.665,"midwest-industries-drop-in-mlok-carbine.big_hole_from_slot0":5.5,"midwest-industries-drop-in-mlok-carbine.big_hole_height":0.58,"midwest-industries-drop-in-mlok-carbine.big_hole_length":0.785,"midwest-industries-drop-in-mlok-carbine.bottom_cut_from_slot0":5.95,"midwest-industries-drop-in-mlok-carbine.bottom_cut_height":0.12,"midwest-industries-drop-in-mlok-carbine.bottom_half_width":0.46,"midwest-industries-drop-in-mlok-carbine.channel_roof_below_top":0.15,"midwest-industries-drop-in-mlok-carbine.collar_id":1.6,"midwest-industries-drop-in-mlok-carbine.collar_od":1.74,"midwest-industries-drop-in-mlok-carbine.front_from_slot0":6.03,"midwest-industries-drop-in-mlok-carbine.front_round":0.25,"midwest-industries-drop-in-mlok-carbine.height":2.25,"midwest-industries-drop-in-mlok-carbine.hole_pitch":0.732,"midwest-industries-drop-in-mlok-carbine.lower_bottom_below_top":1.473,"midwest-industries-drop-in-mlok-carbine.lower_front_from_slot0":6.14,"midwest-industries-drop-in-mlok-carbine.lower_rear_from_slot0":0.245,"midwest-industries-drop-in-mlok-carbine.lower_top_below_top":1.07,"midwest-industries-drop-in-mlok-carbine.mlok_below_top":1.31,"midwest-industries-drop-in-mlok-carbine.mlok_slot0_from_slot0":1.4,"midwest-industries-drop-in-mlok-carbine.mlok_slot0_x":2.436,"midwest-industries-drop-in-mlok-carbine.mlok_slots":3,"midwest-industries-drop-in-mlok-carbine.neck_foot_below_top":0.41,"midwest-industries-drop-in-mlok-carbine.qd_d":0.34,"midwest-industries-drop-in-mlok-carbine.qd_front_from_slot0":5.6,"midwest-industries-drop-in-mlok-carbine.qd_rear_from_slot0":0.266,"midwest-industries-drop-in-mlok-carbine.rail_slot0_x":1.036,"midwest-industries-drop-in-mlok-carbine.rail_slots":15,"midwest-industries-drop-in-mlok-carbine.rail_top_above_bore":1.2125,"midwest-industries-drop-in-mlok-carbine.rear_x":0.336,"midwest-industries-drop-in-mlok-carbine.seam_below_top":0.979,"midwest-industries-drop-in-mlok-carbine.seam_groove":0.02,"midwest-industries-drop-in-mlok-carbine.shoulder_top_below_top":0.18,"midwest-industries-drop-in-mlok-carbine.tongue_rear_from_slot0":1.06,"midwest-industries-drop-in-mlok-carbine.tongue_thickness":0.12,"midwest-industries-drop-in-mlok-carbine.upper_half_width":1.7,"midwest-industries-drop-in-mlok-carbine.upper_hole0_from_slot0":0.311,"midwest-industries-drop-in-mlok-carbine.upper_hole_below_top":0.7,"midwest-industries-drop-in-mlok-carbine.upper_hole_d":0.59,"midwest-industries-drop-in-mlok-carbine.upper_holes":7,"midwest-industries-drop-in-mlok-carbine.upper_rear_from_slot0":0.336,"midwest-industries-drop-in-mlok-carbine.wall":0.08,"midwest-industries-drop-in-mlok-carbine.width":1.83,"std.ar15.barrel_nut_flange_od":1.56,"std.ar15.slip_ring_notch_width":0.203,"std.ar15.slip_ring_skirt_d":1.75,"std.mlok.slot_corner_r":0.0937007874015748,"std.mlok.slot_length":1.2598425196850394,"std.mlok.slot_pitch":1.574803149606299,"std.mlok.slot_width":0.2755905511811024,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{},"features":{},"placement":{},"bounds":{"min":[0,-1.0375,-0.915],"max":[7.176,1.2125,0.915]},"volume_in3":3.0656,"centroid":[3.6163,0.2238,0],"shell":[3.6268,0.1634,0],"area_in2":84.0336,"triangles":18572,"manifold":true,"slabs":[[0,-0.87,-0.87,0.399,1.212,0.87],[0.399,-1.038,-0.915,7.176,1.212,0.915]],"slots":["body"]},"midwest-industries-drop-in-mlok-mid":{"part":"midwest-industries-drop-in-mlok-mid","model":"midwest-industries-drop-in-mlok-mid.glb","script":"midwest_industries_drop_in_mlok_mid.py","inputs":{"bcm-front-sight-base-f-750.port_from_rear":0.27,"bcm-front-sight-base-f-750.ring_r":0.44,"midwest-industries-drop-in-mlok-mid.base_rear_x":8.86,"midwest-industries-drop-in-mlok-mid.bevel_hole0_from_slot0":0.428,"midwest-industries-drop-in-mlok-mid.bevel_hole_d":0.6,"midwest-industries-drop-in-mlok-mid.bevel_holes":10,"midwest-industries-drop-in-mlok-mid.big_hole_below_top":0.7,"midwest-industries-drop-in-mlok-mid.big_hole_from_slot0":7.144,"midwest-industries-drop-in-mlok-mid.big_hole_height":0.56,"midwest-industries-drop-in-mlok-mid.big_hole_length":0.84,"midwest-industries-drop-in-mlok-mid.bottom_cut_from_slot0":7.714,"midwest-industries-drop-in-mlok-mid.bottom_cut_height":0.12,"midwest-industries-drop-in-mlok-mid.bottom_half_width":0.4,"midwest-industries-drop-in-mlok-mid.channel_roof_below_top":0.15,"midwest-industries-drop-in-mlok-mid.collar_id":1.6,"midwest-industries-drop-in-mlok-mid.collar_od":1.74,"midwest-industries-drop-in-mlok-mid.front_from_slot0":8.044,"midwest-industries-drop-in-mlok-mid.front_round":0.25,"midwest-industries-drop-in-mlok-mid.height":2.25,"midwest-industries-drop-in-mlok-mid.hole_pitch":0.731,"midwest-industries-drop-in-mlok-mid.lower_bottom_below_top":1.542,"midwest-industries-drop-in-mlok-mid.lower_front_from_slot0":8.084,"midwest-industries-drop-in-mlok-mid.lower_rear_from_slot0":0.156,"midwest-industries-drop-in-mlok-mid.lower_top_below_top":1.067,"midwest-industries-drop-in-mlok-mid.mlok_below_top":1.38,"midwest-industries-drop-in-mlok-mid.mlok_slot0_from_slot0":1.634,"midwest-industries-drop-in-mlok-mid.mlok_slot0_x":2.576,"midwest-industries-drop-in-mlok-mid.mlok_slots":4,"midwest-industries-drop-in-mlok-mid.neck_foot_below_top":0.43,"midwest-industries-drop-in-mlok-mid.qd_d":0.375,"midwest-industries-drop-in-mlok-mid.qd_front_from_slot0":7.604,"midwest-industries-drop-in-mlok-mid.qd_rear_from_slot0":0.394,"midwest-industries-drop-in-mlok-mid.rail_slot0_x":0.942,"midwest-industries-drop-in-mlok-mid.rail_slots":20,"midwest-industries-drop-in-mlok-mid.rail_top_above_bore":1.2125,"midwest-industries-drop-in-mlok-mid.rear_x":0.336,"midwest-industries-drop-in-mlok-mid.seam_below_top":0.978,"midwest-industries-drop-in-mlok-mid.seam_groove":0.02,"midwest-industries-drop-in-mlok-mid.shoulder_top_below_top":0.204,"midwest-industries-drop-in-mlok-mid.tongue_rear_from_slot0":0.996,"midwest-industries-drop-in-mlok-mid.tongue_thickness":0.12,"midwest-industries-drop-in-mlok-mid.upper_half_width":1.7,"midwest-industries-drop-in-mlok-mid.upper_hole0_from_slot0":0.502,"midwest-industries-drop-in-mlok-mid.upper_hole_below_top":0.7,"midwest-industries-drop-in-mlok-mid.upper_hole_d":0.59,"midwest-industries-drop-in-mlok-mid.upper_holes":9,"midwest-industries-drop-in-mlok-mid.upper_rear_from_slot0":0.406,"midwest-industries-drop-in-mlok-mid.wall":0.08,"midwest-industries-drop-in-mlok-mid.width":1.83,"std.ar15.barrel_nut_flange_od":1.56,"std.ar15.slip_ring_notch_width":0.203,"std.ar15.slip_ring_skirt_d":1.75,"std.mlok.slot_corner_r":0.0937007874015748,"std.mlok.slot_length":1.2598425196850394,"std.mlok.slot_pitch":1.574803149606299,"std.mlok.slot_width":0.2755905511811024,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{},"features":{},"placement":{},"bounds":{"min":[0,-1.0375,-0.915],"max":[9.026,1.2125,0.915]},"volume_in3":4.0812,"centroid":[4.5865,0.267,0],"shell":[4.5785,0.1772,0],"area_in2":106.7333,"triangles":22434,"manifold":true,"slabs":[[0,-0.87,-0.87,0.785,1.212,0.87],[0.785,-1.038,-0.915,9.026,1.212,0.915]],"slots":["body"]},"midwest-mk2-qd-t2-226":{"part":"midwest-mk2-qd-t2-226","model":"midwest-mk2-qd-t2-226.glb","script":"midwest_mk2_qd_t2.py","inputs":{"midwest-mk2-qd-t2-226.deck_above_rail":1.671,"midwest-mk2-qd-t2-226.web_fillet":0.08,"midwest-mk2-qd-t2-226.web_length":0.95,"midwest-mk2-qd-t2-226.web_oval_groove":0.03,"midwest-mk2-qd-t2-226.web_oval_height":0.9,"midwest-mk2-qd-t2-226.web_oval_length":0.45,"midwest-mk2-qd-t2-lower-13.base_half_width":0.49,"midwest-mk2-qd-t2-lower-13.base_top_above_rail":0.35,"midwest-mk2-qd-t2-lower-13.clamp_below_rail":0.277,"midwest-mk2-qd-t2-lower-13.deck_above_rail":1.1,"midwest-mk2-qd-t2-lower-13.deck_hole_across":0.4,"midwest-mk2-qd-t2-lower-13.deck_hole_d":0.129,"midwest-mk2-qd-t2-lower-13.deck_hole_spacing":1.418,"midwest-mk2-qd-t2-lower-13.deck_length":1.985,"midwest-mk2-qd-t2-lower-13.deck_lip_height":0.049,"midwest-mk2-qd-t2-lower-13.deck_thickness":0.173,"midwest-mk2-qd-t2-lower-13.deck_width":0.897,"midwest-mk2-qd-t2-lower-13.deck_x":-0.01,"midwest-mk2-qd-t2-lower-13.edge_break":0.012,"midwest-mk2-qd-t2-lower-13.jaw_groove_pitch":0.076,"midwest-mk2-qd-t2-lower-13.jaw_groove_rear_x":0.505,"midwest-mk2-qd-t2-lower-13.jaw_groove_width":0.022,"midwest-mk2-qd-t2-lower-13.lever_flute_pitch":0.187,"midwest-mk2-qd-t2-lower-13.lever_flute_rear_x":-1.182,"midwest-mk2-qd-t2-lower-13.lever_flute_width":0.04,"midwest-mk2-qd-t2-lower-13.lever_groove_depth":0.02,"midwest-mk2-qd-t2-lower-13.lever_thickness":0.17,"midwest-mk2-qd-t2-lower-13.lever_window_bottom":-0.14,"midwest-mk2-qd-t2-lower-13.lever_window_front_x":0.297,"midwest-mk2-qd-t2-lower-13.lever_window_rear_x":-0.35,"midwest-mk2-qd-t2-lower-13.lever_window_top":0.089,"midwest-mk2-qd-t2-lower-13.lock_button_bottom":-0.114,"midwest-mk2-qd-t2-lower-13.lock_button_front_x":0.16,"midwest-mk2-qd-t2-lower-13.lock_button_rear_x":-0.241,"midwest-mk2-qd-t2-lower-13.lock_button_top":0.068,"midwest-mk2-qd-t2-lower-13.mount_length":1.405,"midwest-mk2-qd-t2-lower-13.nut_across":0.504,"midwest-mk2-qd-t2-lower-13.nut_rib_bottom":-0.134,"midwest-mk2-qd-t2-lower-13.nut_rib_inner_x":0.26,"midwest-mk2-qd-t2-lower-13.nut_rib_outer_x":0.4,"midwest-mk2-qd-t2-lower-13.nut_rib_proud":0.03,"midwest-mk2-qd-t2-lower-13.nut_rib_top":0.15,"midwest-mk2-qd-t2-lower-13.nut_screw_d":0.154,"midwest-mk2-qd-t2-lower-13.nut_thickness":0.1,"midwest-mk2-qd-t2-lower-13.shaft_d":0.2,"midwest-mk2-qd-t2-lower-13.web_groove_depth":0.03,"midwest-mk2-qd-t2-lower-13.web_width":0.5,"std.density.aluminium":1.568,"std.density.steel":4.565,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.top_width":0.835},"profiles":{},"features":{},"placement":{},"bounds":{"min":[-1.302,-0.343,-0.596],"max":[0.985,1.671,0.66]},"volume_in3":1.5906,"centroid":[-0.0413,0.6485,0.0561],"shell":[-0.0626,0.6283,0.0739],"area_in2":16.0557,"triangles":3788,"manifold":true,"rail_seat":{"x":[-0.714,0.704],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-1.302,-0.269,-0.449,-0.921,1.671,0.66],[-0.921,-0.343,-0.49,-0.54,1.671,0.66],[-0.54,-0.343,-0.596,0.604,1.671,0.66],[0.604,-0.33,-0.49,0.985,1.671,0.66]],"slots":["mount","hardware"]},"midwest-mk2-qd-t2-low":{"part":"midwest-mk2-qd-t2-low","model":"midwest-mk2-qd-t2-low.glb","script":"midwest_mk2_qd_t2.py","inputs":{"midwest-mk2-qd-t2-low.deck_above_rail":0.525,"midwest-mk2-qd-t2-lower-13.base_half_width":0.49,"midwest-mk2-qd-t2-lower-13.base_top_above_rail":0.35,"midwest-mk2-qd-t2-lower-13.clamp_below_rail":0.277,"midwest-mk2-qd-t2-lower-13.deck_above_rail":1.1,"midwest-mk2-qd-t2-lower-13.deck_hole_across":0.4,"midwest-mk2-qd-t2-lower-13.deck_hole_d":0.129,"midwest-mk2-qd-t2-lower-13.deck_hole_spacing":1.418,"midwest-mk2-qd-t2-lower-13.deck_length":1.985,"midwest-mk2-qd-t2-lower-13.deck_lip_height":0.049,"midwest-mk2-qd-t2-lower-13.deck_thickness":0.173,"midwest-mk2-qd-t2-lower-13.deck_width":0.897,"midwest-mk2-qd-t2-lower-13.deck_x":-0.01,"midwest-mk2-qd-t2-lower-13.edge_break":0.012,"midwest-mk2-qd-t2-lower-13.jaw_groove_pitch":0.076,"midwest-mk2-qd-t2-lower-13.jaw_groove_rear_x":0.505,"midwest-mk2-qd-t2-lower-13.jaw_groove_width":0.022,"midwest-mk2-qd-t2-lower-13.lever_flute_pitch":0.187,"midwest-mk2-qd-t2-lower-13.lever_flute_rear_x":-1.182,"midwest-mk2-qd-t2-lower-13.lever_flute_width":0.04,"midwest-mk2-qd-t2-lower-13.lever_groove_depth":0.02,"midwest-mk2-qd-t2-lower-13.lever_thickness":0.17,"midwest-mk2-qd-t2-lower-13.lever_window_bottom":-0.14,"midwest-mk2-qd-t2-lower-13.lever_window_front_x":0.297,"midwest-mk2-qd-t2-lower-13.lever_window_rear_x":-0.35,"midwest-mk2-qd-t2-lower-13.lever_window_top":0.089,"midwest-mk2-qd-t2-lower-13.lock_button_bottom":-0.114,"midwest-mk2-qd-t2-lower-13.lock_button_front_x":0.16,"midwest-mk2-qd-t2-lower-13.lock_button_rear_x":-0.241,"midwest-mk2-qd-t2-lower-13.lock_button_top":0.068,"midwest-mk2-qd-t2-lower-13.mount_length":1.405,"midwest-mk2-qd-t2-lower-13.nut_across":0.504,"midwest-mk2-qd-t2-lower-13.nut_rib_bottom":-0.134,"midwest-mk2-qd-t2-lower-13.nut_rib_inner_x":0.26,"midwest-mk2-qd-t2-lower-13.nut_rib_outer_x":0.4,"midwest-mk2-qd-t2-lower-13.nut_rib_proud":0.03,"midwest-mk2-qd-t2-lower-13.nut_rib_top":0.15,"midwest-mk2-qd-t2-lower-13.nut_screw_d":0.154,"midwest-mk2-qd-t2-lower-13.nut_thickness":0.1,"midwest-mk2-qd-t2-lower-13.shaft_d":0.2,"midwest-mk2-qd-t2-lower-13.web_width":0.5,"std.density.aluminium":1.568,"std.density.steel":4.565,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.top_width":0.835},"profiles":{},"features":{},"placement":{},"bounds":{"min":[-1.302,-0.343,-0.596],"max":[0.985,0.525,0.66]},"volume_in3":1.0499,"centroid":[-0.0575,0.1853,0.0849],"shell":[-0.0901,0.1459,0.1034],"area_in2":11.4711,"triangles":2850,"manifold":true,"rail_seat":{"x":[-0.714,0.704],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-1.302,-0.269,-0.449,-0.921,0.525,0.66],[-0.921,-0.343,-0.49,-0.54,0.525,0.66],[-0.54,-0.343,-0.596,0.604,0.525,0.66],[0.604,-0.33,-0.49,0.985,0.525,0.66]],"slots":["mount","hardware"]},"midwest-mk2-qd-t2-lower-13":{"part":"midwest-mk2-qd-t2-lower-13","model":"midwest-mk2-qd-t2-lower-13.glb","script":"midwest_mk2_qd_t2.py","inputs":{"midwest-mk2-qd-t2-lower-13.base_half_width":0.49,"midwest-mk2-qd-t2-lower-13.base_top_above_rail":0.35,"midwest-mk2-qd-t2-lower-13.clamp_below_rail":0.277,"midwest-mk2-qd-t2-lower-13.deck_above_rail":1.1,"midwest-mk2-qd-t2-lower-13.deck_hole_across":0.4,"midwest-mk2-qd-t2-lower-13.deck_hole_d":0.129,"midwest-mk2-qd-t2-lower-13.deck_hole_spacing":1.418,"midwest-mk2-qd-t2-lower-13.deck_length":1.985,"midwest-mk2-qd-t2-lower-13.deck_lip_height":0.049,"midwest-mk2-qd-t2-lower-13.deck_thickness":0.173,"midwest-mk2-qd-t2-lower-13.deck_width":0.897,"midwest-mk2-qd-t2-lower-13.deck_x":-0.01,"midwest-mk2-qd-t2-lower-13.edge_break":0.012,"midwest-mk2-qd-t2-lower-13.jaw_groove_pitch":0.076,"midwest-mk2-qd-t2-lower-13.jaw_groove_rear_x":0.505,"midwest-mk2-qd-t2-lower-13.jaw_groove_width":0.022,"midwest-mk2-qd-t2-lower-13.lever_flute_pitch":0.187,"midwest-mk2-qd-t2-lower-13.lever_flute_rear_x":-1.182,"midwest-mk2-qd-t2-lower-13.lever_flute_width":0.04,"midwest-mk2-qd-t2-lower-13.lever_groove_depth":0.02,"midwest-mk2-qd-t2-lower-13.lever_thickness":0.17,"midwest-mk2-qd-t2-lower-13.lever_window_bottom":-0.14,"midwest-mk2-qd-t2-lower-13.lever_window_front_x":0.297,"midwest-mk2-qd-t2-lower-13.lever_window_rear_x":-0.35,"midwest-mk2-qd-t2-lower-13.lever_window_top":0.089,"midwest-mk2-qd-t2-lower-13.lock_button_bottom":-0.114,"midwest-mk2-qd-t2-lower-13.lock_button_front_x":0.16,"midwest-mk2-qd-t2-lower-13.lock_button_rear_x":-0.241,"midwest-mk2-qd-t2-lower-13.lock_button_top":0.068,"midwest-mk2-qd-t2-lower-13.mount_length":1.405,"midwest-mk2-qd-t2-lower-13.nut_across":0.504,"midwest-mk2-qd-t2-lower-13.nut_rib_bottom":-0.134,"midwest-mk2-qd-t2-lower-13.nut_rib_inner_x":0.26,"midwest-mk2-qd-t2-lower-13.nut_rib_outer_x":0.4,"midwest-mk2-qd-t2-lower-13.nut_rib_proud":0.03,"midwest-mk2-qd-t2-lower-13.nut_rib_top":0.15,"midwest-mk2-qd-t2-lower-13.nut_screw_d":0.154,"midwest-mk2-qd-t2-lower-13.nut_thickness":0.1,"midwest-mk2-qd-t2-lower-13.shaft_d":0.2,"midwest-mk2-qd-t2-lower-13.web_groove_depth":0.03,"midwest-mk2-qd-t2-lower-13.web_groove_spacing":0.426,"midwest-mk2-qd-t2-lower-13.web_groove_width":0.038,"midwest-mk2-qd-t2-lower-13.web_width":0.5,"std.density.aluminium":1.568,"std.density.steel":4.565,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.top_width":0.835},"profiles":{"side":[[-1.005,1.138],[-1.005,1.009],[-0.923,0.929],[-0.618,0.929],[-0.572,0.915],[-0.507,0.878],[-0.47,0.841],[-0.43,0.774],[-0.414,0.72],[-0.414,0.517],[-0.425,0.466],[-0.454,0.409],[-0.526,0.337],[-0.714,0.336],[-0.714,0.225],[-0.708,0.22],[-0.714,0.217],[-0.714,-0.11],[-0.705,-0.115],[-0.703,-0.185],[-0.637,-0.257],[-0.62,-0.265],[-0.08,-0.265],[-0.072,-0.273],[0.085,-0.273],[0.101,-0.262],[0.619,-0.262],[0.648,-0.245],[0.702,-0.177],[0.704,0.169],[0.615,0.258],[0.613,0.323],[0.607,0.339],[0.592,0.354],[0.563,0.359],[0.449,0.359],[0.41,0.406],[0.386,0.463],[0.372,0.533],[0.372,0.695],[0.38,0.738],[0.407,0.801],[0.445,0.852],[0.492,0.891],[0.552,0.923],[0.565,0.929],[0.903,0.929],[0.982,1.003],[0.985,1.022],[0.985,1.135],[0.968,1.153],[-0.993,1.153]],"lever":[[-1.302,0.103],[-1.302,0.003],[-1.297,-0.121],[-1.277,-0.168],[-1.24,-0.211],[-1.157,-0.26],[-1.11,-0.269],[-1.019,-0.263],[-0.707,-0.263],[-0.708,-0.328],[-0.693,-0.338],[-0.666,-0.343],[-0.169,-0.338],[-0.136,-0.329],[-0.114,-0.34],[-0.02,-0.343],[0.107,-0.338],[0.12,-0.331],[0.124,-0.318],[0.381,-0.335],[0.521,-0.335],[0.626,-0.329],[0.69,-0.318],[0.708,-0.306],[0.708,-0.198],[0.702,-0.173],[0.708,-0.162],[0.708,-0.066],[0.702,0.166],[0.695,0.234],[-1.16,0.234],[-1.201,0.214],[-1.248,0.181],[-1.288,0.136]]},"features":{"side":{},"lever":{}},"placement":{"side":{"plane":"xy","offset":{}},"lever":{"plane":"xy","offset":{}}},"bounds":{"min":[-1.302,-0.343,-0.596],"max":[0.985,1.1,0.66]},"volume_in3":1.2899,"centroid":[-0.0503,0.402,0.0691],"shell":[-0.0678,0.3916,0.0832],"area_in2":14.2557,"triangles":3186,"manifold":true,"rail_seat":{"x":[-0.714,0.704],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-1.302,-0.269,-0.449,-0.921,1.1,0.66],[-0.921,-0.343,-0.49,-0.54,1.1,0.66],[-0.54,-0.343,-0.596,0.604,1.1,0.66],[0.604,-0.33,-0.49,0.985,1.1,0.66]],"slots":["mount","hardware"]},"nordic-22rb-upper.barrel":{"part":"nordic-22rb-upper","component":"barrel","model":"nordic-22rb-upper.barrel.glb","script":"nordic_22rb_upper.py","inputs":{"nordic-22rb-upper.barrel_od":0.736,"nordic-22rb-upper.bore_axis_above_pin":0.8775,"nordic-22rb-upper.bore_d":0.218,"nordic-22rb-upper.handguard_rear_x":6.597,"nordic-22rb-upper.muzzle_pilot_d":0.443,"nordic-22rb-upper.muzzle_relief_d":0.441,"nordic-22rb-upper.muzzle_shoulder_x":21.134,"nordic-22rb-upper.muzzle_thread_end":0.385,"nordic-22rb-upper.muzzle_thread_length":0.506,"nordic-22rb-upper.muzzle_thread_major_d":0.4957,"nordic-22rb-upper.muzzle_thread_minor_d":0.4551,"nordic-22rb-upper.muzzle_thread_pitch":0.03571,"nordic-22rb-upper.muzzle_thread_start":0.029},"profiles":{},"features":{},"placement":{},"bounds":{"min":[6.597,0.5095,-0.368],"max":[21.64,1.2455,0.368]},"volume_in3":5.7027,"centroid":[13.9539,0.8775,0],"shell":[14.0899,0.8775,0],"area_in2":45.6668,"triangles":3704,"manifold":true,"slabs":[[6.597,0.51,-0.368,21.244,1.245,0.368],[21.244,0.63,-0.248,21.64,1.125,0.248]],"slots":["barrel"]},"nordic-22rb-upper.handguard":{"part":"nordic-22rb-upper","component":"handguard","model":"nordic-22rb-upper.handguard.glb","script":"nordic_22rb_upper.py","inputs":{"nordic-22rb-upper.handguard_bottom_y":0.0765,"nordic-22rb-upper.handguard_center_y":0.8775,"nordic-22rb-upper.handguard_clamp_bottom_y":-0.114,"nordic-22rb-upper.handguard_clamp_corner_front":0.17,"nordic-22rb-upper.handguard_clamp_corner_rear":0.24,"nordic-22rb-upper.handguard_clamp_counterbore_d":0.27,"nordic-22rb-upper.handguard_clamp_flat_front_x":7.955,"nordic-22rb-upper.handguard_clamp_flat_rear_x":7.05,"nordic-22rb-upper.handguard_clamp_front_x":8.33,"nordic-22rb-upper.handguard_clamp_hole_d":0.135,"nordic-22rb-upper.handguard_clamp_rear_x":6.81,"nordic-22rb-upper.handguard_clamp_screw_head_d":0.2,"nordic-22rb-upper.handguard_clamp_screw_rear_x":7.3,"nordic-22rb-upper.handguard_clamp_screw_socket":0.11,"nordic-22rb-upper.handguard_clamp_screw_spacing":0.505,"nordic-22rb-upper.handguard_clamp_screw_y":0.1,"nordic-22rb-upper.handguard_clamp_screws":2,"nordic-22rb-upper.handguard_clamp_side_front_x":8.23,"nordic-22rb-upper.handguard_clamp_side_rear_x":6.85,"nordic-22rb-upper.handguard_clamp_side_top_y":0.283,"nordic-22rb-upper.handguard_clamp_slit_front_x":8.4,"nordic-22rb-upper.handguard_clamp_slit_width":0.059,"nordic-22rb-upper.handguard_clamp_width":1.06,"nordic-22rb-upper.handguard_front_x":20.135,"nordic-22rb-upper.handguard_groove_offset":0.21,"nordic-22rb-upper.handguard_groove_overrun":0.3,"nordic-22rb-upper.handguard_groove_upper_rear_x":6.82,"nordic-22rb-upper.handguard_groove_width":0.044,"nordic-22rb-upper.handguard_id":1.4015748031496063,"nordic-22rb-upper.handguard_nose_opening_d":1.53,"nordic-22rb-upper.handguard_panel_gap":0.31,"nordic-22rb-upper.handguard_panel_length":0.93,"nordic-22rb-upper.handguard_panel_width":0.29,"nordic-22rb-upper.handguard_rail_top_above_pin":2.0824,"nordic-22rb-upper.handguard_rear_x":6.597,"nordic-22rb-upper.handguard_width":1.602,"nordic-22rb-upper.mlok_rear_slot_length":0.93,"nordic-22rb-upper.mlok_slot_front_x":18.976,"nordic-22rb-upper.mlok_slots_per_face":7,"nordic-22rb-upper.rail_front_x":19.98,"std.mlok.slot_corner_r":0.0937007874015748,"std.mlok.slot_length":1.2598425196850394,"std.mlok.slot_pitch":1.574803149606299,"std.mlok.slot_width":0.2755905511811024,"std.picatinny.slot_depth":0.118},"profiles":{"front":[[-0.801,0.75],[-0.797,0.513],[-0.77,0.446],[-0.376,0.048],[-0.279,0.005],[0,0.001],[0.037,0],[0.261,0.003],[0.376,0.049],[0.759,0.429],[0.799,0.529],[0.801,0.807],[0.796,1.105],[0.774,1.162],[0.308,1.638],[0.31,1.782],[0.34,1.83],[0.398,1.878],[0.409,1.924],[0.314,2.009],[-0.221,2.013],[-0.328,2.007],[-0.411,1.921],[-0.388,1.855],[-0.36,1.85],[-0.378,1.845],[-0.374,1.821],[-0.344,1.831],[-0.316,1.786],[-0.306,1.65],[-0.317,1.619],[-0.456,1.488],[-0.769,1.155],[-0.798,1.076]]},"features":{"front":{}},"placement":{"front":{"plane":"zy","offset":{"y":"handguard_bottom_y"}}},"bounds":{"min":[6.597,-0.114,-0.801],"max":[20.135,1.9644,0.801]},"volume_in3":8.7675,"centroid":[12.9748,1.1563,-0.0003],"shell":[13.1102,0.9839,0.0011],"area_in2":130.416,"triangles":33370,"manifold":true,"slabs":[[6.597,-0.114,-0.801,8.19,1.964,0.801],[8.19,0.005,-0.8,8.588,1.964,0.8],[8.588,0.076,-0.801,20.135,1.964,0.801]],"slots":["receiver"]},"nordic-22rb-upper.receiver":{"part":"nordic-22rb-upper","component":"receiver","model":"nordic-22rb-upper.receiver.glb","script":"nordic_22rb_upper.py","inputs":{"nordic-22rb-upper.bolt_catch_relief_front_x":3.473,"nordic-22rb-upper.bolt_catch_relief_rear_x":2.555,"nordic-22rb-upper.bolt_catch_relief_top_y":0.6,"nordic-22rb-upper.bolt_flat_bottom_y":0.985,"nordic-22rb-upper.bolt_flat_top_y":1.285,"nordic-22rb-upper.bolt_front_corner_r":0.05,"nordic-22rb-upper.bolt_front_x":5.18,"nordic-22rb-upper.bolt_pin_seat_d":0.205,"nordic-22rb-upper.bolt_pin_socket_d":0.101,"nordic-22rb-upper.bolt_pin_x":5,"nordic-22rb-upper.bolt_pin_y":1.187,"nordic-22rb-upper.bolt_rear_corner_r":0.143,"nordic-22rb-upper.bolt_rear_x":3.6,"nordic-22rb-upper.bolt_top_break":0.054,"nordic-22rb-upper.bore_axis_above_pin":0.8775,"nordic-22rb-upper.charging_handle_latch_thickness":0.124,"nordic-22rb-upper.charging_handle_plate_top_y":1.89,"nordic-22rb-upper.charging_handle_recess_r":0.455,"nordic-22rb-upper.charging_handle_recess_web":0.155,"nordic-22rb-upper.charging_handle_slot_bottom_y":1.699,"nordic-22rb-upper.charging_handle_slot_length":0.81,"nordic-22rb-upper.charging_handle_slot_top_y":1.846,"nordic-22rb-upper.charging_handle_t_bottom_y":1.597,"nordic-22rb-upper.charging_handle_t_depth":0.496,"nordic-22rb-upper.charging_handle_t_top_y":2.047,"nordic-22rb-upper.charging_handle_t_width":1.97,"nordic-22rb-upper.ejection_port_bottom_y":0.833,"nordic-22rb-upper.ejection_port_corner_r":0.063,"nordic-22rb-upper.ejection_port_front_x":5.283,"nordic-22rb-upper.ejection_port_pocket_bottom_y":0.811,"nordic-22rb-upper.ejection_port_pocket_corner_r":0.16,"nordic-22rb-upper.ejection_port_pocket_depth":0.232,"nordic-22rb-upper.ejection_port_pocket_front_x":5.326,"nordic-22rb-upper.ejection_port_pocket_rear_x":3.529,"nordic-22rb-upper.ejection_port_pocket_top_y":1.452,"nordic-22rb-upper.ejection_port_rear_x":3.565,"nordic-22rb-upper.ejection_port_top_y":1.309,"nordic-22rb-upper.extractor_bottom_y":0.84,"nordic-22rb-upper.extractor_front_x":4.936,"nordic-22rb-upper.extractor_notch_r":0.07,"nordic-22rb-upper.extractor_notch_top_y":0.976,"nordic-22rb-upper.extractor_notch_x":4.798,"nordic-22rb-upper.extractor_pivot_front_x":4.869,"nordic-22rb-upper.extractor_pivot_rear_x":4.748,"nordic-22rb-upper.extractor_rear_x":4.395,"nordic-22rb-upper.extractor_rod_d":0.019,"nordic-22rb-upper.extractor_spring_d":0.04,"nordic-22rb-upper.extractor_spring_front_x":4.554,"nordic-22rb-upper.extractor_spring_pitch":0.037,"nordic-22rb-upper.extractor_top_y":0.924,"nordic-22rb-upper.handguard_bottom_y":0.0765,"nordic-22rb-upper.handguard_center_y":0.8775,"nordic-22rb-upper.handguard_rear_x":6.597,"nordic-22rb-upper.latch_window_bottom_y":1.585,"nordic-22rb-upper.latch_window_front_x":0.446,"nordic-22rb-upper.latch_window_rear_x":0.245,"nordic-22rb-upper.latch_window_top_y":1.949,"nordic-22rb-upper.lug_hole_d":0.251,"nordic-22rb-upper.rail_front_x":19.98,"nordic-22rb-upper.rail_rear_x":0.57,"nordic-22rb-upper.rail_slot0_x":0.795,"nordic-22rb-upper.rail_tongue_bottom_y":1.905,"nordic-22rb-upper.rail_tongue_rear_x":-0.684,"nordic-22rb-upper.rail_tongue_width":0.64,"nordic-22rb-upper.rail_top_above_pin":2.09,"nordic-22rb-upper.rear_behind_pin":0.86,"nordic-22rb-upper.receiver_bore_d":0.851,"nordic-22rb-upper.receiver_chamfer_bottom_y":1.177,"nordic-22rb-upper.receiver_flare_start_x":6.19,"nordic-22rb-upper.receiver_lower_corner_w":0.134,"nordic-22rb-upper.receiver_lower_corner_y":0.631,"nordic-22rb-upper.receiver_lug_width":0.49,"nordic-22rb-upper.receiver_rear_chamfer_front_x":3,"nordic-22rb-upper.receiver_rear_chamfer_runout":0.22,"nordic-22rb-upper.receiver_rear_chamfer_w":0.23,"nordic-22rb-upper.width":1.31,"std.ar15.bolt_catch_boss_out":0.618,"std.ar15.bore_axis_y":0.8775,"std.ar15.buffer_tower_front_x":-0.628,"std.ar15.buffer_tower_od":1.392,"std.ar15.buffer_trough_r":0.5625,"std.ar15.deck_y":0.2485,"std.ar15.pin_spacing":6.375,"std.ar15.rear_lug_slot_rear_x":-0.402,"std.ar15.rear_lug_slot_width":0.5,"std.ar15.rear_wall_arc_r":0.75,"std.ar15.upper_rear_face_x":-0.621,"std.picatinny.slot_depth":0.118},"profiles":{"side":[[-0.86,1.592],[-0.673,1.541],[-0.708,1.102],[-0.694,0.858],[-0.578,0.528],[-0.489,0.504],[-0.272,0.327],[-0.253,-0.188],[-0.211,-0.222],[0.069,-0.227],[0.234,-0.197],[0.24,0.168],[0.273,0.219],[0.358,0.218],[0.385,0.18],[0.517,0.215],[0.648,0.213],[0.685,0.184],[0.798,0.229],[1.088,0.243],[5.954,0.235],[6.038,0.224],[6.047,0.168],[6.094,0.214],[6.141,0.213],[6.173,0.179],[6.196,-0.111],[6.312,-0.202],[6.443,-0.214],[6.579,-0.146],[6.628,-0.062],[6.62,0.031],[6.653,0.064],[6.84,0.032],[7.081,-0.112],[7.577,-0.111],[7.604,-0.149],[7.642,-0.122],[7.848,-0.106],[7.941,-0.127],[8.14,0.01],[8.347,0.072],[15.207,0.049],[20.135,0.068],[20.135,1.958],[20.049,1.96],[20.009,2.068],[19.977,2.083],[19.817,2.076],[19.713,1.965],[19.634,1.99],[19.612,2.089],[19.443,2.082],[19.363,2.042],[19.32,1.963],[19.231,1.997],[19.209,2.086],[19.041,2.08],[18.97,2.039],[18.936,1.969],[18.861,1.971],[18.83,2.06],[18.788,2.084],[18.629,2.077],[18.543,1.967],[18.468,1.968],[18.423,2.081],[18.255,2.084],[18.184,2.043],[18.15,1.964],[18.061,1.989],[18.039,2.078],[17.871,2.081],[17.8,2.04],[17.766,1.961],[17.691,1.962],[17.646,2.085],[17.469,2.088],[17.407,2.047],[17.373,1.968],[17.298,1.969],[17.244,2.082],[17.076,2.085],[16.961,1.966],[16.896,1.967],[16.864,2],[16.86,2.089],[16.673,2.083],[16.596,1.972],[16.503,1.973],[16.471,2.007],[16.467,2.086],[16.308,2.089],[16.218,2.03],[16.227,1.992],[16.194,1.96],[16.11,1.971],[16.065,2.084],[15.896,2.087],[15.81,1.966],[15.754,1.967],[15.684,2.001],[15.681,2.081],[15.532,2.093],[15.461,2.052],[15.417,1.964],[15.314,1.975],[15.279,2.088],[15.148,2.09],[15.077,2.058],[15.024,1.961],[14.921,1.972],[14.886,2.085],[14.708,2.088],[14.65,1.967],[14.537,1.969],[14.493,2.082],[14.315,2.086],[14.281,1.997],[14.219,1.965],[14.144,1.967],[14.112,2],[14.109,2.089],[13.941,2.092],[13.864,1.972],[13.742,1.974],[13.697,2.087],[13.557,2.089],[13.514,2.066],[13.48,1.969],[13.349,1.971],[13.314,2.093],[13.211,2.095],[13.145,2.087],[13.068,1.966],[12.965,1.968],[12.911,2.091],[12.743,2.084],[12.694,1.973],[12.563,1.975],[12.527,2.088],[12.368,2.091],[12.335,2.068],[12.334,2.002],[12.263,1.961],[12.16,1.972],[12.139,2.08],[12.078,2.096],[11.966,2.088],[11.941,2.009],[11.87,1.968],[11.777,1.979],[11.732,2.092],[11.582,2.095],[11.524,1.974],[11.374,1.977],[11.348,2.089],[11.189,2.092],[11.122,1.971],[10.991,1.974],[10.946,2.087],[10.787,2.099],[10.771,2.001],[10.719,1.969],[10.598,1.971],[10.553,2.093],[10.394,2.096],[10.354,1.975],[10.223,1.968],[10.172,1.992],[10.169,2.091],[10.01,2.093],[9.961,1.982],[9.84,1.975],[9.779,1.999],[9.767,2.097],[9.655,2.099],[9.603,2.086],[9.568,1.979],[9.493,1.971],[9.409,1.982],[9.378,2.081],[9.346,2.095],[9.205,2.088],[9.199,2.009],[9.119,1.978],[9.016,1.979],[8.981,2.092],[8.822,2.095],[8.806,2.006],[8.763,1.974],[8.623,1.977],[8.588,2.09],[8.428,2.092],[8.413,2.004],[8.323,1.972],[8.23,1.983],[8.195,2.096],[8.036,2.099],[7.987,1.978],[7.865,1.98],[7.814,2.004],[7.792,2.094],[7.633,2.106],[7.594,1.994],[7.453,1.978],[7.421,2.011],[7.422,2.077],[7.352,2.101],[7.24,2.094],[7.191,1.982],[7.098,1.975],[7.037,1.999],[7.006,2.098],[6.847,2.1],[6.831,2.012],[6.789,1.98],[6.658,1.982],[6.636,2.062],[6.585,2.105],[6.445,2.098],[6.429,2.009],[6.358,1.978],[6.255,1.98],[6.211,2.093],[6.052,2.105],[6.036,2.016],[5.946,1.975],[5.872,1.977],[5.808,2.099],[5.64,2.102],[5.61,1.991],[5.497,1.974],[5.437,2.008],[5.424,2.097],[5.331,2.108],[5.266,2.109],[5.241,2.011],[5.198,1.979],[5.076,1.981],[5.013,2.104],[4.854,2.106],[4.814,1.985],[4.711,1.978],[4.66,2.002],[4.629,2.101],[4.461,2.104],[4.412,1.983],[4.309,1.985],[4.236,2.098],[4.068,2.101],[4.052,2.012],[3.972,1.972],[3.916,1.982],[3.834,2.105],[3.712,2.107],[3.651,2.094],[3.65,2.01],[3.607,1.978],[3.523,1.989],[3.501,2.05],[3.422,2.103],[3.282,2.105],[3.233,1.994],[3.13,1.977],[3.088,2.01],[3.098,2.047],[3.01,2.11],[2.879,2.103],[2.864,2.014],[2.821,1.982],[2.727,1.983],[2.701,2.059],[2.58,2.108],[2.477,2.1],[2.461,2.011],[2.381,1.98],[2.325,1.981],[2.302,2.005],[2.321,2.051],[2.252,2.104],[2.074,2.098],[2.068,2.018],[1.96,1.978],[1.914,2.063],[1.831,2.102],[1.691,2.104],[1.666,2.016],[1.623,1.984],[1.548,1.985],[1.526,2.055],[1.502,2.042],[1.466,2.099],[1.297,2.101],[1.263,2.013],[1.202,1.972],[1.164,1.973],[1.11,2.067],[0.998,2.107],[0.905,2.108],[0.861,2.011],[0.799,1.979],[0.753,1.98],[0.73,2.05],[0.652,2.103],[-0.359,2.102],[-0.528,2.095],[-0.631,2.05],[-0.846,2.063]],"handle":[[-0.869,0.681],[-0.865,0.673],[-0.868,0.573],[-0.863,0.567],[-0.861,0.439],[-0.856,-0.747],[-0.849,-0.818],[-0.833,-0.867],[-0.807,-0.912],[-0.771,-0.952],[-0.738,-0.977],[-0.696,-0.998],[-0.641,-1.013],[-0.569,-1.019],[-0.529,-1.014],[-0.509,-1.048],[-0.489,-1.063],[-0.439,-1.072],[-0.196,-1.04],[-0.142,-1.016],[-0.111,-0.981],[-0.091,-0.931],[-0.096,-0.876],[-0.104,-0.858],[-0.136,-0.85],[-0.136,-0.837],[-0.123,-0.819],[-0.138,-0.785],[-0.166,-0.781],[-0.173,-0.774],[-0.158,-0.747],[-0.169,-0.715],[-0.176,-0.708],[-0.191,-0.71],[-0.206,-0.701],[-0.18,-0.652],[-0.176,-0.611],[-0.163,-0.571],[-0.134,-0.527],[-0.11,-0.505],[-0.08,-0.485],[-0.042,-0.471],[0.054,-0.454],[0.081,-0.456],[0.114,-0.446],[0.334,-0.421],[0.419,-0.406],[0.441,-0.393],[0.454,-0.371],[0.446,-0.294],[0.437,-0.282],[0.355,-0.22],[0.351,-0.216],[0.357,-0.211],[1.064,-0.21],[1.072,0.197],[0.473,0.195],[0.085,0.201],[0.08,0.216],[0.079,0.313],[0.07,0.319],[-0.04,0.332],[-0.132,0.362],[-0.207,0.409],[-0.283,0.492],[-0.316,0.547],[-0.332,0.59],[-0.339,0.664],[-0.334,0.685],[-0.341,0.696],[-0.344,0.783],[-0.354,0.833],[-0.385,0.897],[-0.415,0.934],[-0.453,0.97],[-0.478,0.981],[-0.707,0.985],[-0.739,0.97],[-0.783,0.93],[-0.81,0.889],[-0.818,0.886],[-0.815,0.881],[-0.826,0.875],[-0.823,0.866],[-0.866,0.767],[-0.861,0.756]]},"features":{"side":{},"handle":{"latch":[[[0.347,-0.202],[0.262,-0.218],[0.251,-0.29],[0.222,-0.311],[0.188,-0.322],[0.151,-0.313],[0.075,-0.274],[0.006,-0.328],[-0.063,-0.347],[-0.136,-0.377],[-0.207,-0.426],[-0.276,-0.51],[-0.32,-0.604],[-0.334,-0.671],[-0.351,-0.742],[-0.362,-0.808],[-0.39,-0.869],[-0.432,-0.92],[-0.483,-0.954],[-0.522,-0.972],[-0.524,-1.065],[-0.439,-1.068],[-0.319,-1.055],[-0.201,-1.044],[-0.14,-1.015],[-0.108,-0.965],[-0.094,-0.914],[-0.095,-0.871],[-0.14,-0.847],[-0.129,-0.811],[-0.174,-0.777],[-0.16,-0.738],[-0.207,-0.699],[-0.182,-0.649],[-0.173,-0.589],[-0.139,-0.522],[-0.08,-0.481],[-0.003,-0.465],[0.118,-0.445],[0.288,-0.423],[0.433,-0.396],[0.453,-0.354],[0.436,-0.281]]]}},"placement":{"side":{"plane":"xy","offset":{}},"handle":{"plane":"xz","offset":{}}},"bounds":{"min":[-0.86,-0.227,-1.068],"max":[6.597,2.09,0.985]},"volume_in3":13.6299,"centroid":[2.9103,1.0421,-0.0103],"shell":[2.7211,1.1466,-0.0087],"area_in2":61.0213,"triangles":12550,"manifold":true,"rear_corner":{"r":0.75,"centre":[0.122,0.9985],"x":[-0.628,-0.0116],"reach_z":0.696,"trough_r":0.5625},"slabs":[[-0.86,0.486,-1.067,-0.468,2.09,0.985],[-0.468,-0.224,-1.068,-0.075,2.09,0.976],[-0.075,-0.227,-0.655,0.317,2.09,0.655],[0.317,0.249,-0.655,0.71,2.09,0.655],[0.71,0.249,-0.655,5.812,1.972,0.655],[5.812,-0.118,-0.66,6.205,1.972,0.66],[6.205,-0.214,-0.801,6.597,1.972,0.801]],"slots":["receiver","bolt","charging_handle","extractor"]},"nordic-thread-protector":{"part":"nordic-thread-protector","model":"nordic-thread-protector.glb","script":"nordic_thread_protector.py","inputs":{"nordic-22rb-upper.muzzle_thread_length":0.506,"nordic-22rb-upper.muzzle_thread_major_d":0.4957,"nordic-22rb-upper.muzzle_thread_minor_d":0.4551,"nordic-22rb-upper.muzzle_thread_pitch":0.03571,"nordic-22rb-upper.muzzle_thread_start":0.029,"nordic-thread-protector.length":0.511,"nordic-thread-protector.od":0.736},"profiles":{},"features":{},"placement":{},"bounds":{"min":[0,-0.368,-0.368],"max":[0.511,0.368,0.368]},"volume_in3":0.1234,"centroid":[0.2555,0,-0.0001],"shell":[0.2555,0.0002,-0.0005],"area_in2":2.8378,"triangles":4180,"manifold":true,"slabs":[[0,-0.368,-0.368,0.511,0.368,0.368]],"slots":["body"]},"olight-baldr-s-bl.body":{"part":"olight-baldr-s-bl","component":"body","model":"olight-baldr-s-bl.body.glb","script":"olight_baldr_s_bl.py","inputs":{"olight-baldr-s-bl.adjuster_below_jaw_top":0.755,"olight-baldr-s-bl.adjuster_depth":0.04,"olight-baldr-s-bl.adjuster_diameter":0.125,"olight-baldr-s-bl.adjuster_lr_x":1.23,"olight-baldr-s-bl.adjuster_ud_x":1.49,"olight-baldr-s-bl.axis_above_mount":0.815,"olight-baldr-s-bl.body_front_x":2.11,"olight-baldr-s-bl.body_rear_x":0.338,"olight-baldr-s-bl.body_top_below_jaw_top":0.513,"olight-baldr-s-bl.body_width":1.1,"olight-baldr-s-bl.clamp_front_x":2.084,"olight-baldr-s-bl.clamp_rear_x":1.195,"olight-baldr-s-bl.contact_diameter":0.19,"olight-baldr-s-bl.contact_ring_diameter":0.71,"olight-baldr-s-bl.contact_ring_groove":0.02,"olight-baldr-s-bl.contact_x":1.224,"olight-baldr-s-bl.head_axis_below_jaw_top":0.975,"olight-baldr-s-bl.head_diameter":0.846,"olight-baldr-s-bl.laser_window_above_axis":0.261,"olight-baldr-s-bl.laser_window_diameter":0.124,"olight-baldr-s-bl.length":2.48,"olight-baldr-s-bl.lens_diameter":0.635,"olight-baldr-s-bl.lens_recess":0.06,"olight-baldr-s-bl.rail_face_below_jaw_top":0.16,"olight-baldr-s-bl.rear_switch_width":0.935},"profiles":{"side":[[0,-0.805],[0,-0.963],[0.002,-1.003],[0.016,-1.007],[0.023,-1.031],[0.035,-1.045],[0.05,-1.054],[0.24,-1.102],[0.253,-1.097],[0.259,-1.082],[0.261,-1.102],[0.267,-1.108],[0.319,-1.122],[0.327,-1.122],[0.333,-1.113],[0.337,-1.123],[0.339,-1.208],[0.353,-1.22],[0.34,-1.232],[0.34,-1.352],[0.374,-1.377],[0.453,-1.413],[0.546,-1.412],[0.579,-1.388],[0.596,-1.364],[0.644,-1.413],[0.658,-1.416],[1.204,-1.416],[1.996,-1.414],[2.043,-1.413],[2.057,-1.402],[2.131,-1.397],[2.333,-1.398],[2.346,-1.392],[2.376,-1.397],[2.395,-1.373],[2.413,-1.326],[2.45,-1.152],[2.481,-0.862],[2.487,-0.667],[2.478,-0.59],[2.466,-0.561],[2.444,-0.559],[2.432,-0.563],[2.417,-0.552],[2.185,-0.552],[2.159,-0.54],[2.129,-0.517],[2.106,-0.513],[2.147,-0.461],[2.147,-0.228],[2.14,-0.221],[2.085,-0.22],[2.083,-0.075],[2.071,-0.057],[2.019,-0.015],[1.98,-0.004],[1.282,0],[1.253,-0.011],[1.207,-0.055],[1.195,-0.081],[1.193,-0.146],[1.186,-0.148],[1.162,-0.178],[1.113,-0.171],[0.609,-0.19],[0.59,-0.196],[0.577,-0.214],[0.58,-0.476],[0.575,-0.482],[0.576,-0.513],[0.556,-0.514],[0.477,-0.557],[0.453,-0.558],[0.351,-0.616],[0.336,-0.626],[0.336,-0.645],[0.331,-0.655],[0.316,-0.645],[0.294,-0.647],[0.217,-0.7],[0.019,-0.759],[0.005,-0.778]],"front":[[0,-0.719],[0.003,-0.872],[0.03,-0.918],[0.032,-1.312],[0.056,-1.361],[0.087,-1.392],[0.128,-1.413],[0.472,-1.413],[0.515,-1.421],[0.609,-1.421],[0.643,-1.413],[0.985,-1.411],[1.03,-1.384],[1.059,-1.35],[1.08,-1.299],[1.083,-0.912],[1.104,-0.88],[1.11,-0.864],[1.11,-0.633],[1.091,-0.582],[1.075,-0.555],[1.061,-0.547],[1.069,-0.531],[1.069,-0.49],[1.076,-0.484],[1.272,-0.478],[1.279,-0.472],[1.279,-0.41],[1.265,-0.399],[1.271,-0.38],[1.271,-0.343],[1.26,-0.316],[1.271,-0.302],[1.268,-0.216],[1.229,-0.199],[1.135,-0.199],[1.128,-0.192],[1.128,-0.176],[1.122,-0.164],[1.076,-0.164],[1.069,-0.157],[1.067,-0.047],[1.036,-0.016],[1.012,0],[0.928,0],[0.913,-0.017],[0.908,-0.05],[0.892,-0.06],[0.897,-0.066],[0.892,-0.079],[0.895,-0.085],[0.932,-0.122],[0.909,-0.153],[0.903,-0.146],[0.903,-0.136],[0.896,-0.126],[0.845,-0.113],[0.818,-0.113],[0.813,-0.118],[0.692,-0.118],[0.686,-0.113],[0.474,-0.113],[0.455,-0.121],[0.34,-0.121],[0.334,-0.116],[0.313,-0.116],[0.254,-0.129],[0.219,-0.148],[0.212,-0.154],[0.21,-0.206],[0.203,-0.212],[0.196,-0.206],[0.196,-0.149],[0.172,-0.12],[0.199,-0.09],[0.199,-0.069],[0.193,-0.055],[0.196,-0.009],[0.192,-0.005],[0.117,-0.005],[0.106,-0.013],[0.067,-0.05],[0.059,-0.063],[0.056,-0.458],[0.062,-0.549],[0.055,-0.556],[0.039,-0.556],[0.032,-0.563],[0.013,-0.6],[0.003,-0.641]]},"features":{"side":{},"front":{}},"placement":{"side":{"plane":"xy","offset":{}},"front":{"plane":"zy","offset":{}}},"bounds":{"min":[-1.6395,0.353,-0.55],"max":[0.8405,1.26,0.55]},"volume_in3":2.0597,"centroid":[-0.3698,0.8017,0.0003],"shell":[-0.361,0.8073,-0.0012],"area_in2":13.345,"triangles":11568,"manifold":true,"slabs":[[-1.64,0.454,-0.55,-1.285,1.256,0.55],[-1.285,0.353,-0.55,0.84,1.26,0.55]],"slots":["body","bezel","lens","laser","contact"]},"olight-baldr-s-bl.rail_clamp":{"part":"olight-baldr-s-bl","component":"rail_clamp","model":"olight-baldr-s-bl.rail_clamp.glb","script":"olight_baldr_s_bl.py","inputs":{"olight-baldr-s-bl.adjuster_below_jaw_top":0.755,"olight-baldr-s-bl.adjuster_depth":0.04,"olight-baldr-s-bl.adjuster_diameter":0.125,"olight-baldr-s-bl.adjuster_lr_x":1.23,"olight-baldr-s-bl.adjuster_ud_x":1.49,"olight-baldr-s-bl.axis_above_mount":0.815,"olight-baldr-s-bl.body_front_x":2.11,"olight-baldr-s-bl.body_rear_x":0.338,"olight-baldr-s-bl.body_top_below_jaw_top":0.513,"olight-baldr-s-bl.body_width":1.1,"olight-baldr-s-bl.clamp_front_x":2.084,"olight-baldr-s-bl.clamp_rear_x":1.195,"olight-baldr-s-bl.contact_diameter":0.19,"olight-baldr-s-bl.contact_ring_diameter":0.71,"olight-baldr-s-bl.contact_ring_groove":0.02,"olight-baldr-s-bl.contact_x":1.224,"olight-baldr-s-bl.head_axis_below_jaw_top":0.975,"olight-baldr-s-bl.head_diameter":0.846,"olight-baldr-s-bl.jaw_thickness":0.15,"olight-baldr-s-bl.key_height":0.04,"olight-baldr-s-bl.knob_diameter":0.29,"olight-baldr-s-bl.knob_proud":0.205,"olight-baldr-s-bl.laser_window_above_axis":0.261,"olight-baldr-s-bl.laser_window_diameter":0.124,"olight-baldr-s-bl.length":2.48,"olight-baldr-s-bl.lens_diameter":0.635,"olight-baldr-s-bl.lens_recess":0.06,"olight-baldr-s-bl.lever_rear_x":0.577,"olight-baldr-s-bl.lever_thickness":0.06,"olight-baldr-s-bl.lever_top_below_jaw_top":0.19,"olight-baldr-s-bl.rail_face_below_jaw_top":0.16,"olight-baldr-s-bl.rear_switch_width":0.935,"olight-baldr-s-bl.screw_below_jaw_top":0.337,"olight-baldr-s-bl.screw_diameter":0.2,"olight-baldr-s-bl.screw_x":1.476,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{"side":[[0,-0.805],[0,-0.963],[0.002,-1.003],[0.016,-1.007],[0.023,-1.031],[0.035,-1.045],[0.05,-1.054],[0.24,-1.102],[0.253,-1.097],[0.259,-1.082],[0.261,-1.102],[0.267,-1.108],[0.319,-1.122],[0.327,-1.122],[0.333,-1.113],[0.337,-1.123],[0.339,-1.208],[0.353,-1.22],[0.34,-1.232],[0.34,-1.352],[0.374,-1.377],[0.453,-1.413],[0.546,-1.412],[0.579,-1.388],[0.596,-1.364],[0.644,-1.413],[0.658,-1.416],[1.204,-1.416],[1.996,-1.414],[2.043,-1.413],[2.057,-1.402],[2.131,-1.397],[2.333,-1.398],[2.346,-1.392],[2.376,-1.397],[2.395,-1.373],[2.413,-1.326],[2.45,-1.152],[2.481,-0.862],[2.487,-0.667],[2.478,-0.59],[2.466,-0.561],[2.444,-0.559],[2.432,-0.563],[2.417,-0.552],[2.185,-0.552],[2.159,-0.54],[2.129,-0.517],[2.106,-0.513],[2.147,-0.461],[2.147,-0.228],[2.14,-0.221],[2.085,-0.22],[2.083,-0.075],[2.071,-0.057],[2.019,-0.015],[1.98,-0.004],[1.282,0],[1.253,-0.011],[1.207,-0.055],[1.195,-0.081],[1.193,-0.146],[1.186,-0.148],[1.162,-0.178],[1.113,-0.171],[0.609,-0.19],[0.59,-0.196],[0.577,-0.214],[0.58,-0.476],[0.575,-0.482],[0.576,-0.513],[0.556,-0.514],[0.477,-0.557],[0.453,-0.558],[0.351,-0.616],[0.336,-0.626],[0.336,-0.645],[0.331,-0.655],[0.316,-0.645],[0.294,-0.647],[0.217,-0.7],[0.019,-0.759],[0.005,-0.778]],"front":[[0,-0.719],[0.003,-0.872],[0.03,-0.918],[0.032,-1.312],[0.056,-1.361],[0.087,-1.392],[0.128,-1.413],[0.472,-1.413],[0.515,-1.421],[0.609,-1.421],[0.643,-1.413],[0.985,-1.411],[1.03,-1.384],[1.059,-1.35],[1.08,-1.299],[1.083,-0.912],[1.104,-0.88],[1.11,-0.864],[1.11,-0.633],[1.091,-0.582],[1.075,-0.555],[1.061,-0.547],[1.069,-0.531],[1.069,-0.49],[1.076,-0.484],[1.272,-0.478],[1.279,-0.472],[1.279,-0.41],[1.265,-0.399],[1.271,-0.38],[1.271,-0.343],[1.26,-0.316],[1.271,-0.302],[1.268,-0.216],[1.229,-0.199],[1.135,-0.199],[1.128,-0.192],[1.128,-0.176],[1.122,-0.164],[1.076,-0.164],[1.069,-0.157],[1.067,-0.047],[1.036,-0.016],[1.012,0],[0.928,0],[0.913,-0.017],[0.908,-0.05],[0.892,-0.06],[0.897,-0.066],[0.892,-0.079],[0.895,-0.085],[0.932,-0.122],[0.909,-0.153],[0.903,-0.146],[0.903,-0.136],[0.896,-0.126],[0.845,-0.113],[0.818,-0.113],[0.813,-0.118],[0.692,-0.118],[0.686,-0.113],[0.474,-0.113],[0.455,-0.121],[0.34,-0.121],[0.334,-0.116],[0.313,-0.116],[0.254,-0.129],[0.219,-0.148],[0.212,-0.154],[0.21,-0.206],[0.203,-0.212],[0.196,-0.206],[0.196,-0.149],[0.172,-0.12],[0.199,-0.09],[0.199,-0.069],[0.193,-0.055],[0.196,-0.009],[0.192,-0.005],[0.117,-0.005],[0.106,-0.013],[0.067,-0.05],[0.059,-0.063],[0.056,-0.458],[0.062,-0.549],[0.055,-0.556],[0.039,-0.556],[0.032,-0.563],[0.013,-0.6],[0.003,-0.641]]},"features":{"side":{},"front":{}},"placement":{"side":{"plane":"xy","offset":{}},"front":{"plane":"zy","offset":{}}},"bounds":{"min":[-1.0645,-0.16,-0.5371],"max":[0.5075,0.353,0.7341]},"volume_in3":0.6455,"centroid":[-0.2588,0.1634,0.0316],"shell":[-0.2636,0.1408,0.0905],"area_in2":7.1968,"triangles":2212,"manifold":true,"rail_seat":{"x":[-0.4445,0.4445],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.5091},"slabs":[[-1.064,0.016,-0.529,-0.671,0.353,0.724],[-0.671,-0.16,-0.537,0.115,0.353,0.734],[0.115,-0.157,-0.529,0.507,0.353,0.529]],"slots":["body","hardware"]},"otter-creek-polonium-k":{"part":"otter-creek-polonium-k","model":"otter-creek-polonium-k.glb","script":"otter_creek_polonium_k.py","inputs":{"otter-creek-polonium-k.bore_d":0.287,"otter-creek-polonium-k.can_rear_x":0.435,"otter-creek-polonium-k.collar_notch_width":0.095,"otter-creek-polonium-k.collar_notches":4,"otter-creek-polonium-k.collar_od":0.408,"otter-creek-polonium-k.face_land_d":0.5,"otter-creek-polonium-k.face_pocket_depth":0.017,"otter-creek-polonium-k.face_pocket_r":0.08,"otter-creek-polonium-k.face_pockets":4,"otter-creek-polonium-k.face_rim_width":0.124,"otter-creek-polonium-k.face_spoke_width":0.112,"otter-creek-polonium-k.front_edge_break":0.02,"otter-creek-polonium-k.front_face_x":5.205,"otter-creek-polonium-k.groove_1_x0":4.206,"otter-creek-polonium-k.groove_1_x1":4.48,"otter-creek-polonium-k.groove_2_x0":4.696,"otter-creek-polonium-k.groove_2_x1":4.962,"otter-creek-polonium-k.groove_depth":0.014,"otter-creek-polonium-k.grooves":2,"otter-creek-polonium-k.length":5.3,"otter-creek-polonium-k.mount_hex_end_d":0.76,"otter-creek-polonium-k.mount_hex_flats":0.805,"otter-creek-polonium-k.mount_hex_length":0.39,"otter-creek-polonium-k.mount_plug_length":0.37,"otter-creek-polonium-k.od":1.625,"otter-creek-polonium-k.rear_chamfer_x":0.616,"otter-creek-polonium-k.rear_rim_d":1.49,"otter-creek-polonium-k.thread_major_d":0.4957,"otter-creek-polonium-k.thread_minor_d":0.4551,"otter-creek-polonium-k.thread_pitch":0.03571},"profiles":{},"features":{},"placement":{},"bounds":{"min":[0,-0.8125,-0.8125],"max":[5.3,0.8125,0.8125]},"volume_in3":9.4693,"centroid":[2.7895,0,0],"shell":[2.4687,0,0.0001],"area_in2":39.6529,"triangles":13742,"manifold":true,"slabs":[[0,-0.403,-0.465,0.379,0.403,0.465],[0.379,-0.813,-0.813,5.3,0.813,0.813]],"slots":["body","mount"]},"otter-creek-polonium":{"part":"otter-creek-polonium","model":"otter-creek-polonium.glb","script":"otter_creek_polonium.py","inputs":{"otter-creek-polonium.bore_d":0.291,"otter-creek-polonium.can_rear_x":0.381,"otter-creek-polonium.collar_notch_width":0.093,"otter-creek-polonium.collar_notches":4,"otter-creek-polonium.collar_od":0.43,"otter-creek-polonium.face_land_d":0.503,"otter-creek-polonium.face_pocket_depth":0.01,"otter-creek-polonium.face_pocket_r":0.07,"otter-creek-polonium.face_pockets":4,"otter-creek-polonium.face_rim_width":0.103,"otter-creek-polonium.face_spoke_width":0.111,"otter-creek-polonium.front_edge_break":0.02,"otter-creek-polonium.front_face_x":6.238,"otter-creek-polonium.groove_1_x0":4.26,"otter-creek-polonium.groove_1_x1":4.525,"otter-creek-polonium.groove_2_x0":4.754,"otter-creek-polonium.groove_2_x1":5.016,"otter-creek-polonium.groove_3_x0":5.249,"otter-creek-polonium.groove_3_x1":5.503,"otter-creek-polonium.groove_4_x0":5.743,"otter-creek-polonium.groove_4_x1":6.005,"otter-creek-polonium.groove_depth":0.014,"otter-creek-polonium.grooves":4,"otter-creek-polonium.length":6.3,"otter-creek-polonium.mount_hex_end_d":0.79,"otter-creek-polonium.mount_hex_flats":0.803,"otter-creek-polonium.mount_hex_length":0.34,"otter-creek-polonium.mount_plug_length":0.25,"otter-creek-polonium.od":1.625,"otter-creek-polonium.rear_chamfer_x":0.603,"otter-creek-polonium.rear_rim_d":1.49,"otter-creek-polonium.thread_major_d":0.4957,"otter-creek-polonium.thread_minor_d":0.4551,"otter-creek-polonium.thread_pitch":0.03571},"profiles":{},"features":{},"placement":{},"bounds":{"min":[0,-0.8125,-0.8125],"max":[6.3,0.8125,0.8125]},"volume_in3":11.5344,"centroid":[3.2913,0,0],"shell":[2.9549,0,-0.0001],"area_in2":46.105,"triangles":14540,"manifold":true,"slabs":[[0,-0.749,-0.749,0.394,0.749,0.749],[0.394,-0.813,-0.813,6.3,0.813,0.813]],"slots":["body","mount"]},"panzer-ar57-buffer":{"part":"panzer-ar57-buffer","model":"panzer-ar57-buffer.glb","script":"panzer_ar57_buffer.py","inputs":{"panzer-ar57-buffer.length":3.251,"panzer-ar57-buffer.od":0.98,"std.carbine_buffer.body_d":0.687,"std.carbine_buffer.body_length":2.854,"std.carbine_buffer.body_start":0.5145,"std.carbine_buffer.bumper_band":0.06,"std.carbine_buffer.bumper_d":0.687,"std.carbine_buffer.bumper_exposed":0.4,"std.carbine_buffer.bumper_taper":13.5,"std.carbine_buffer.head_d":0.98,"std.carbine_buffer.head_flat_across":0.952,"std.carbine_buffer.head_rim":0.214,"std.carbine_buffer.head_thickness":0.254,"std.carbine_buffer.length":3.251,"std.carbine_buffer.pilot_d":0.781,"std.carbine_buffer.pilot_end":0.468,"std.carbine_buffer.pin_d":0.122,"std.carbine_buffer.pin_from_open_end":0.24},"profiles":{},"bounds":{"min":[0,-0.49,-0.49],"max":[3.251,0.462,0.49]},"volume_in3":1.2939,"centroid":[1.4641,0,0],"shell":[1.5949,0,0],"area_in2":9.6585,"triangles":7276,"manifold":true,"slabs":[[0,-0.49,-0.49,0.361,0.462,0.49],[0.361,-0.391,-0.391,3.251,0.391,0.391]],"slots":["body","bumper","pin"]},"panzer-ar57-ult-12-upper.barrel":{"part":"panzer-ar57-ult-12-upper","component":"barrel","model":"panzer-ar57-ult-12-upper.barrel.glb","script":"panzer_ar57_ult_upper.py","inputs":{"fn-p90-50-magazine.height":0.77,"fn-p90-50-magazine.width":1.949,"panzer-ar57-ult-12-upper.barrel_od":0.53,"panzer-ar57-ult-12-upper.barrel_rear_x":5.508,"panzer-ar57-ult-12-upper.bolt_end_d":0.75,"panzer-ar57-ult-12-upper.bolt_end_proud":0.05,"panzer-ar57-ult-12-upper.bolt_window_depth":0.3,"panzer-ar57-ult-12-upper.bolt_window_front_x":3.999,"panzer-ar57-ult-12-upper.bolt_window_rear_x":3.141,"panzer-ar57-ult-12-upper.bore_axis_above_pin":0.951,"panzer-ar57-ult-12-upper.bore_d":0.224,"panzer-ar57-ult-12-upper.brake_band_front_x":17.926,"panzer-ar57-ult-12-upper.brake_bore_d":0.204,"panzer-ar57-ult-12-upper.brake_groove_depth":0.02,"panzer-ar57-ult-12-upper.brake_groove_w":0.03,"panzer-ar57-ult-12-upper.brake_od":0.625,"panzer-ar57-ult-12-upper.brake_port_columns":3,"panzer-ar57-ult-12-upper.brake_port_d":0.156,"panzer-ar57-ult-12-upper.brake_port_phase":19.5,"panzer-ar57-ult-12-upper.brake_port_pitch":0.262,"panzer-ar57-ult-12-upper.brake_port_x":18.319,"panzer-ar57-ult-12-upper.brake_ports_around":6,"panzer-ar57-ult-12-upper.brake_rear_x":17.444,"panzer-ar57-ult-12-upper.brake_slot_depth":0.477,"panzer-ar57-ult-12-upper.brake_slot_width":0.204,"panzer-ar57-ult-12-upper.catch_bottom_y":1.799,"panzer-ar57-ult-12-upper.catch_front_x":3.16,"panzer-ar57-ult-12-upper.catch_out":0.3,"panzer-ar57-ult-12-upper.catch_rear_x":2.9,"panzer-ar57-ult-12-upper.catch_top_y":2.185,"panzer-ar57-ult-12-upper.channel_bottom_y":0.358,"panzer-ar57-ult-12-upper.channel_depth":0.1,"panzer-ar57-ult-12-upper.channel_front_x":6.988,"panzer-ar57-ult-12-upper.channel_gap":0.03,"panzer-ar57-ult-12-upper.channel_rear_x":0.774,"panzer-ar57-ult-12-upper.channel_top_y":0.865,"panzer-ar57-ult-12-upper.cross_hole_d":0.171,"panzer-ar57-ult-12-upper.cross_hole_depth":0.1,"panzer-ar57-ult-12-upper.cross_hole_y":2.27,"panzer-ar57-ult-12-upper.feed_notch_length":1.462,"panzer-ar57-ult-12-upper.feed_pocket_d":1.883,"panzer-ar57-ult-12-upper.feed_pocket_floor_y":1.063,"panzer-ar57-ult-12-upper.feed_pocket_x":5.056,"panzer-ar57-ult-12-upper.front_block_face_x":14.951,"panzer-ar57-ult-12-upper.front_block_rear_x":14.866,"panzer-ar57-ult-12-upper.front_hole_pitch":0.2653,"panzer-ar57-ult-12-upper.front_hole_x":15.139,"panzer-ar57-ult-12-upper.front_hole_y":2.23,"panzer-ar57-ult-12-upper.front_rail_front_x":16.247,"panzer-ar57-ult-12-upper.front_rail_slot0_x":15.187,"panzer-ar57-ult-12-upper.front_rail_slots":3,"panzer-ar57-ult-12-upper.front_rail_top_above_pin":2.55,"panzer-ar57-ult-12-upper.handguard_bottom_y":0.098,"panzer-ar57-ult-12-upper.handguard_front_x":17.202,"panzer-ar57-ult-12-upper.handguard_rear_bottom_x":7.246,"panzer-ar57-ult-12-upper.handguard_rear_top_x":6.589,"panzer-ar57-ult-12-upper.handguard_wall":0.12,"panzer-ar57-ult-12-upper.handguard_width":1.44,"panzer-ar57-ult-12-upper.handle_bottom_y":0.433,"panzer-ar57-ult-12-upper.handle_front_x":6.907,"panzer-ar57-ult-12-upper.handle_out":0.2,"panzer-ar57-ult-12-upper.handle_rear_x":5.296,"panzer-ar57-ult-12-upper.handle_top_y":0.79,"panzer-ar57-ult-12-upper.keel_top_y":0.241,"panzer-ar57-ult-12-upper.keel_width":0.67,"panzer-ar57-ult-12-upper.latch_bottom_y":1.76,"panzer-ar57-ult-12-upper.latch_top_y":2.1,"panzer-ar57-ult-12-upper.latch_width":0.62,"panzer-ar57-ult-12-upper.lower_chamfer_top_y":0.649,"panzer-ar57-ult-12-upper.lower_face_angle":133.34,"panzer-ar57-ult-12-upper.lower_hole_pitch":0.3174,"panzer-ar57-ult-12-upper.lower_hole_x":15.326,"panzer-ar57-ult-12-upper.lower_hole_y":0.157,"panzer-ar57-ult-12-upper.lower_rail_bottom_y":-0.093,"panzer-ar57-ult-12-upper.lower_rail_slot0_x":15.279,"panzer-ar57-ult-12-upper.lug_clearance":0.005,"panzer-ar57-ult-12-upper.mag_rear_x":4.082,"panzer-ar57-ult-12-upper.mag_underside_y":1.635,"panzer-ar57-ult-12-upper.mlok_lower_axis_y":1.0297,"panzer-ar57-ult-12-upper.mlok_lower_face_distance":0.785,"panzer-ar57-ult-12-upper.mlok_lower_front_x":15.389,"panzer-ar57-ult-12-upper.mlok_lower_slots":5,"panzer-ar57-ult-12-upper.mlok_lower_y":0.491,"panzer-ar57-ult-12-upper.mlok_lower_z":0.5709,"panzer-ar57-ult-12-upper.mlok_upper_front_x":16.328,"panzer-ar57-ult-12-upper.mlok_upper_slots":6,"panzer-ar57-ult-12-upper.mlok_upper_y":0.984,"panzer-ar57-ult-12-upper.muzzle_end_x":19.58,"panzer-ar57-ult-12-upper.muzzle_end_x_pinframe":19.58,"panzer-ar57-ult-12-upper.nut_height":0.722,"panzer-ar57-ult-12-upper.nut_rear_x":17.221,"panzer-ar57-ult-12-upper.rail_block_front_x":3.98,"panzer-ar57-ult-12-upper.rail_front_x":3.979,"panzer-ar57-ult-12-upper.rail_rear_x":-1.767,"panzer-ar57-ult-12-upper.rail_rear_x_pinframe":-1.767,"panzer-ar57-ult-12-upper.rail_slot0_x":-1.216,"panzer-ar57-ult-12-upper.rail_slots":13,"panzer-ar57-ult-12-upper.rail_top_above_pin":2.543,"panzer-ar57-ult-12-upper.receiver_chamfer_front_low_x":3.557,"panzer-ar57-ult-12-upper.receiver_chamfer_front_low_y":1.278,"panzer-ar57-ult-12-upper.receiver_chamfer_front_top_x":3.69,"panzer-ar57-ult-12-upper.receiver_chamfer_front_top_y":1.42,"panzer-ar57-ult-12-upper.receiver_chamfer_top_y":1.506,"panzer-ar57-ult-12-upper.receiver_rear_x":-0.621,"panzer-ar57-ult-12-upper.receiver_top_y":1.524,"panzer-ar57-ult-12-upper.riser_width":0.62,"panzer-ar57-ult-12-upper.side_face_bottom_y":0.26,"panzer-ar57-ult-12-upper.side_face_top_y":1.26,"panzer-ar57-ult-12-upper.takedown_lug_front_x":0.22,"panzer-ar57-ult-12-upper.top_flat_width":0.835,"panzer-ar57-ult-12-upper.tray_dip_rear_x":13.551,"panzer-ar57-ult-12-upper.tray_front_y":1.362,"panzer-ar57-ult-12-upper.tray_top_y":1.635,"panzer-ar57-ult-12-upper.underside_y":0.2485,"panzer-ar57-ult-12-upper.width":1.44,"panzer-ar57-ult-12-upper.window2_front_x":2.601,"panzer-ar57-ult-12-upper.window2_rear_x":2.292,"panzer-ar57-ult-12-upper.window_bottom_y":1.758,"panzer-ar57-ult-12-upper.window_front_x":3.544,"panzer-ar57-ult-12-upper.window_rear_x":2.946,"panzer-ar57-ult-12-upper.window_top_y":2.131,"std.ar15.bore_axis_y":0.8775,"std.ar15.buffer_tower_front_x":-0.628,"std.ar15.buffer_tower_od":1.392,"std.ar15.buffer_tower_top_y":1.5735,"std.ar15.buffer_trough_r":0.5625,"std.ar15.deck_y":0.2485,"std.ar15.front_lug_slot_width":0.5,"std.ar15.pin_spacing":6.375,"std.ar15.rear_lug_slot_rear_x":-0.402,"std.ar15.rear_lug_slot_width":0.5,"std.ar15.rear_wall_arc_r":0.75,"std.mlok.slot_corner_r":0.0937007874015748,"std.mlok.slot_length":1.2598425196850394,"std.mlok.slot_pitch":1.574803149606299,"std.mlok.slot_width":0.2755905511811024,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{"side":[[-1.767,2.126],[-1.749,2.06],[-1.66,1.979],[-1.525,1.925],[-1.383,1.905],[-1.218,1.863],[-1.081,1.787],[-1.028,1.739],[-0.976,1.652],[-0.947,1.625],[-0.66,1.529],[-0.509,1.498],[-0.47,1.472],[-0.527,1.408],[-0.58,1.301],[-0.573,1.121],[-0.583,1.11],[-0.574,1.025],[-0.584,1.015],[-0.569,0.856],[-0.821,0.918],[-0.8,0.811],[-0.758,0.703],[-0.658,0.554],[-0.534,0.432],[-0.421,0.358],[-0.331,0.316],[-0.277,0.306],[-0.237,0.279],[-0.217,-0.167],[-0.177,-0.204],[-0.1,-0.225],[0.367,-0.22],[0.378,-0.231],[0.439,-0.199],[0.453,-0.172],[0.45,-0.023],[0.46,-0.013],[0.446,0.147],[0.453,0.189],[0.477,0.216],[0.807,0.219],[0.819,0.209],[1.722,0.217],[1.734,0.206],[3.454,0.221],[3.466,0.211],[4.272,0.218],[4.283,0.207],[6.137,0.213],[6.153,0.197],[6.164,-0.036],[6.189,-0.11],[6.261,-0.189],[6.368,-0.23],[6.516,-0.218],[6.846,-0.056],[7.17,0.042],[7.244,0.042],[7.254,0.053],[7.375,0.044],[7.385,0.054],[8.1,0.061],[8.111,0.05],[10.913,0.065],[10.923,0.054],[12.065,0.064],[12.075,0.054],[12.201,0.065],[12.211,0.055],[14.009,0.061],[14.019,0.05],[14.218,0.062],[14.228,0.052],[14.437,0.043],[14.563,0.003],[14.832,-0.12],[14.935,-0.151],[15.352,-0.137],[15.394,-0.157],[15.456,-0.157],[15.467,-0.146],[15.55,-0.145],[15.561,-0.135],[15.717,-0.133],[15.748,-0.154],[15.841,-0.153],[15.852,-0.143],[16.05,-0.13],[16.06,-0.141],[16.112,-0.14],[16.143,-0.161],[16.175,-0.15],[16.31,-0.149],[16.321,-0.138],[16.582,-0.145],[16.677,-0.053],[16.701,-0.011],[16.706,0.064],[16.767,0.183],[17.047,0.527],[17.202,0.528],[17.202,1.158],[17.151,1.158],[17.11,1.178],[17.079,1.178],[17.014,1.256],[16.988,1.309],[16.931,1.332],[16.869,1.391],[16.761,1.565],[16.657,1.819],[16.558,2.011],[16.381,2.2],[16.371,2.233],[16.331,2.288],[16.302,2.343],[16.291,2.448],[16.245,2.508],[16.183,2.551],[16.066,2.55],[15.905,2.473],[15.869,2.532],[15.843,2.548],[15.705,2.547],[15.512,2.469],[15.487,2.518],[15.44,2.556],[15.312,2.555],[15.13,2.467],[15.093,2.493],[15.057,2.553],[14.882,2.546],[14.879,2.394],[14.819,2.298],[14.809,1.702],[14.855,1.749],[14.851,1.503],[14.707,1.357],[13.575,1.637],[8.898,1.61],[8.887,1.62],[5.772,1.595],[5.761,1.606],[4.518,1.595],[4.475,1.615],[4.176,1.613],[4.159,1.629],[4.114,2.38],[4.147,2.367],[4.145,2.4],[4.094,2.449],[3.961,2.535],[3.639,2.532],[3.593,2.423],[3.448,2.509],[3.372,2.53],[3.243,2.529],[3.196,2.431],[3.029,2.528],[2.858,2.526],[2.799,2.439],[2.643,2.525],[2.461,2.523],[2.428,2.463],[2.402,2.446],[2.269,2.511],[2.181,2.532],[2.064,2.52],[2.016,2.454],[1.973,2.454],[1.86,2.519],[1.709,2.528],[1.7,2.517],[1.667,2.517],[1.608,2.451],[1.442,2.515],[1.27,2.514],[1.232,2.459],[1.189,2.459],[1.012,2.523],[0.904,2.522],[0.835,2.456],[0.813,2.456],[0.625,2.52],[0.507,2.519],[0.438,2.453],[0.26,2.517],[0.099,2.516],[0.05,2.461],[0.007,2.461],[-0.116,2.514],[-0.267,2.513],[-0.318,2.491],[-0.347,2.458],[-0.369,2.458],[-0.535,2.511],[-0.675,2.51],[-0.745,2.455],[-0.933,2.508],[-1.073,2.507],[-1.122,2.463],[-1.176,2.463],[-1.288,2.505],[-1.654,2.503],[-1.715,2.469],[-1.738,2.431],[-1.734,2.387],[-1.702,2.338],[-1.758,2.356],[-1.732,2.312],[-1.726,2.257],[-1.736,2.246],[-1.729,2.181]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{}}},"bounds":{"min":[5.508,0.59,-0.3126],"max":[19.58,1.312,0.3126]},"volume_in3":2.6113,"centroid":[12.6419,0.951,0],"shell":[12.8919,0.951,0],"area_in2":35.8086,"triangles":4332,"manifold":true,"slabs":[[5.508,0.686,-0.265,16.844,1.216,0.265],[16.844,0.59,-0.313,19.189,1.312,0.313],[19.189,0.656,-0.295,19.58,1.246,0.295]],"slots":["barrel"]},"panzer-ar57-ult-12-upper.handguard":{"part":"panzer-ar57-ult-12-upper","component":"handguard","model":"panzer-ar57-ult-12-upper.handguard.glb","script":"panzer_ar57_ult_upper.py","inputs":{"fn-p90-50-magazine.height":0.77,"fn-p90-50-magazine.width":1.949,"panzer-ar57-ult-12-upper.barrel_od":0.53,"panzer-ar57-ult-12-upper.barrel_rear_x":5.508,"panzer-ar57-ult-12-upper.bolt_end_d":0.75,"panzer-ar57-ult-12-upper.bolt_end_proud":0.05,"panzer-ar57-ult-12-upper.bolt_window_depth":0.3,"panzer-ar57-ult-12-upper.bolt_window_front_x":3.999,"panzer-ar57-ult-12-upper.bolt_window_rear_x":3.141,"panzer-ar57-ult-12-upper.bore_axis_above_pin":0.951,"panzer-ar57-ult-12-upper.catch_bottom_y":1.799,"panzer-ar57-ult-12-upper.catch_front_x":3.16,"panzer-ar57-ult-12-upper.catch_out":0.3,"panzer-ar57-ult-12-upper.catch_rear_x":2.9,"panzer-ar57-ult-12-upper.catch_top_y":2.185,"panzer-ar57-ult-12-upper.channel_bottom_y":0.358,"panzer-ar57-ult-12-upper.channel_depth":0.1,"panzer-ar57-ult-12-upper.channel_front_x":6.988,"panzer-ar57-ult-12-upper.channel_gap":0.03,"panzer-ar57-ult-12-upper.channel_rear_x":0.774,"panzer-ar57-ult-12-upper.channel_top_y":0.865,"panzer-ar57-ult-12-upper.cross_hole_d":0.171,"panzer-ar57-ult-12-upper.cross_hole_depth":0.1,"panzer-ar57-ult-12-upper.cross_hole_y":2.27,"panzer-ar57-ult-12-upper.feed_notch_length":1.462,"panzer-ar57-ult-12-upper.feed_pocket_d":1.883,"panzer-ar57-ult-12-upper.feed_pocket_floor_y":1.063,"panzer-ar57-ult-12-upper.feed_pocket_x":5.056,"panzer-ar57-ult-12-upper.front_block_face_x":14.951,"panzer-ar57-ult-12-upper.front_block_rear_x":14.866,"panzer-ar57-ult-12-upper.front_hole_pitch":0.2653,"panzer-ar57-ult-12-upper.front_hole_x":15.139,"panzer-ar57-ult-12-upper.front_hole_y":2.23,"panzer-ar57-ult-12-upper.front_rail_front_x":16.247,"panzer-ar57-ult-12-upper.front_rail_slot0_x":15.187,"panzer-ar57-ult-12-upper.front_rail_slots":3,"panzer-ar57-ult-12-upper.front_rail_top_above_pin":2.55,"panzer-ar57-ult-12-upper.handguard_bottom_y":0.098,"panzer-ar57-ult-12-upper.handguard_front_x":17.202,"panzer-ar57-ult-12-upper.handguard_rear_bottom_x":7.246,"panzer-ar57-ult-12-upper.handguard_rear_top_x":6.589,"panzer-ar57-ult-12-upper.handguard_wall":0.12,"panzer-ar57-ult-12-upper.handguard_width":1.44,"panzer-ar57-ult-12-upper.handle_bottom_y":0.433,"panzer-ar57-ult-12-upper.handle_front_x":6.907,"panzer-ar57-ult-12-upper.handle_out":0.2,"panzer-ar57-ult-12-upper.handle_rear_x":5.296,"panzer-ar57-ult-12-upper.handle_top_y":0.79,"panzer-ar57-ult-12-upper.keel_top_y":0.241,"panzer-ar57-ult-12-upper.keel_width":0.67,"panzer-ar57-ult-12-upper.latch_bottom_y":1.76,"panzer-ar57-ult-12-upper.latch_top_y":2.1,"panzer-ar57-ult-12-upper.latch_width":0.62,"panzer-ar57-ult-12-upper.lower_chamfer_top_y":0.649,"panzer-ar57-ult-12-upper.lower_face_angle":133.34,"panzer-ar57-ult-12-upper.lower_hole_pitch":0.3174,"panzer-ar57-ult-12-upper.lower_hole_x":15.326,"panzer-ar57-ult-12-upper.lower_hole_y":0.157,"panzer-ar57-ult-12-upper.lower_rail_bottom_y":-0.093,"panzer-ar57-ult-12-upper.lower_rail_slot0_x":15.279,"panzer-ar57-ult-12-upper.lug_clearance":0.005,"panzer-ar57-ult-12-upper.mag_rear_x":4.082,"panzer-ar57-ult-12-upper.mag_underside_y":1.635,"panzer-ar57-ult-12-upper.mlok_lower_axis_y":1.0297,"panzer-ar57-ult-12-upper.mlok_lower_face_distance":0.785,"panzer-ar57-ult-12-upper.mlok_lower_front_x":15.389,"panzer-ar57-ult-12-upper.mlok_lower_slots":5,"panzer-ar57-ult-12-upper.mlok_lower_y":0.491,"panzer-ar57-ult-12-upper.mlok_lower_z":0.5709,"panzer-ar57-ult-12-upper.mlok_upper_front_x":16.328,"panzer-ar57-ult-12-upper.mlok_upper_slots":6,"panzer-ar57-ult-12-upper.mlok_upper_y":0.984,"panzer-ar57-ult-12-upper.muzzle_end_x":19.58,"panzer-ar57-ult-12-upper.muzzle_end_x_pinframe":19.58,"panzer-ar57-ult-12-upper.rail_block_front_x":3.98,"panzer-ar57-ult-12-upper.rail_front_x":3.979,"panzer-ar57-ult-12-upper.rail_rear_x":-1.767,"panzer-ar57-ult-12-upper.rail_rear_x_pinframe":-1.767,"panzer-ar57-ult-12-upper.rail_slot0_x":-1.216,"panzer-ar57-ult-12-upper.rail_slots":13,"panzer-ar57-ult-12-upper.rail_top_above_pin":2.543,"panzer-ar57-ult-12-upper.receiver_chamfer_front_low_x":3.557,"panzer-ar57-ult-12-upper.receiver_chamfer_front_low_y":1.278,"panzer-ar57-ult-12-upper.receiver_chamfer_front_top_x":3.69,"panzer-ar57-ult-12-upper.receiver_chamfer_front_top_y":1.42,"panzer-ar57-ult-12-upper.receiver_chamfer_top_y":1.506,"panzer-ar57-ult-12-upper.receiver_rear_x":-0.621,"panzer-ar57-ult-12-upper.receiver_top_y":1.524,"panzer-ar57-ult-12-upper.riser_width":0.62,"panzer-ar57-ult-12-upper.side_face_bottom_y":0.26,"panzer-ar57-ult-12-upper.side_face_top_y":1.26,"panzer-ar57-ult-12-upper.takedown_lug_front_x":0.22,"panzer-ar57-ult-12-upper.top_flat_width":0.835,"panzer-ar57-ult-12-upper.tray_dip_rear_x":13.551,"panzer-ar57-ult-12-upper.tray_front_y":1.362,"panzer-ar57-ult-12-upper.tray_top_y":1.635,"panzer-ar57-ult-12-upper.underside_y":0.2485,"panzer-ar57-ult-12-upper.width":1.44,"panzer-ar57-ult-12-upper.window2_front_x":2.601,"panzer-ar57-ult-12-upper.window2_rear_x":2.292,"panzer-ar57-ult-12-upper.window_bottom_y":1.758,"panzer-ar57-ult-12-upper.window_front_x":3.544,"panzer-ar57-ult-12-upper.window_rear_x":2.946,"panzer-ar57-ult-12-upper.window_top_y":2.131,"std.ar15.bore_axis_y":0.8775,"std.ar15.buffer_tower_front_x":-0.628,"std.ar15.buffer_tower_od":1.392,"std.ar15.buffer_tower_top_y":1.5735,"std.ar15.buffer_trough_r":0.5625,"std.ar15.deck_y":0.2485,"std.ar15.front_lug_slot_width":0.5,"std.ar15.pin_spacing":6.375,"std.ar15.rear_lug_slot_rear_x":-0.402,"std.ar15.rear_lug_slot_width":0.5,"std.ar15.rear_wall_arc_r":0.75,"std.mlok.slot_corner_r":0.0937007874015748,"std.mlok.slot_length":1.2598425196850394,"std.mlok.slot_pitch":1.574803149606299,"std.mlok.slot_width":0.2755905511811024,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{"side":[[-1.767,2.126],[-1.749,2.06],[-1.66,1.979],[-1.525,1.925],[-1.383,1.905],[-1.218,1.863],[-1.081,1.787],[-1.028,1.739],[-0.976,1.652],[-0.947,1.625],[-0.66,1.529],[-0.509,1.498],[-0.47,1.472],[-0.527,1.408],[-0.58,1.301],[-0.573,1.121],[-0.583,1.11],[-0.574,1.025],[-0.584,1.015],[-0.569,0.856],[-0.821,0.918],[-0.8,0.811],[-0.758,0.703],[-0.658,0.554],[-0.534,0.432],[-0.421,0.358],[-0.331,0.316],[-0.277,0.306],[-0.237,0.279],[-0.217,-0.167],[-0.177,-0.204],[-0.1,-0.225],[0.367,-0.22],[0.378,-0.231],[0.439,-0.199],[0.453,-0.172],[0.45,-0.023],[0.46,-0.013],[0.446,0.147],[0.453,0.189],[0.477,0.216],[0.807,0.219],[0.819,0.209],[1.722,0.217],[1.734,0.206],[3.454,0.221],[3.466,0.211],[4.272,0.218],[4.283,0.207],[6.137,0.213],[6.153,0.197],[6.164,-0.036],[6.189,-0.11],[6.261,-0.189],[6.368,-0.23],[6.516,-0.218],[6.846,-0.056],[7.17,0.042],[7.244,0.042],[7.254,0.053],[7.375,0.044],[7.385,0.054],[8.1,0.061],[8.111,0.05],[10.913,0.065],[10.923,0.054],[12.065,0.064],[12.075,0.054],[12.201,0.065],[12.211,0.055],[14.009,0.061],[14.019,0.05],[14.218,0.062],[14.228,0.052],[14.437,0.043],[14.563,0.003],[14.832,-0.12],[14.935,-0.151],[15.352,-0.137],[15.394,-0.157],[15.456,-0.157],[15.467,-0.146],[15.55,-0.145],[15.561,-0.135],[15.717,-0.133],[15.748,-0.154],[15.841,-0.153],[15.852,-0.143],[16.05,-0.13],[16.06,-0.141],[16.112,-0.14],[16.143,-0.161],[16.175,-0.15],[16.31,-0.149],[16.321,-0.138],[16.582,-0.145],[16.677,-0.053],[16.701,-0.011],[16.706,0.064],[16.767,0.183],[17.047,0.527],[17.202,0.528],[17.202,1.158],[17.151,1.158],[17.11,1.178],[17.079,1.178],[17.014,1.256],[16.988,1.309],[16.931,1.332],[16.869,1.391],[16.761,1.565],[16.657,1.819],[16.558,2.011],[16.381,2.2],[16.371,2.233],[16.331,2.288],[16.302,2.343],[16.291,2.448],[16.245,2.508],[16.183,2.551],[16.066,2.55],[15.905,2.473],[15.869,2.532],[15.843,2.548],[15.705,2.547],[15.512,2.469],[15.487,2.518],[15.44,2.556],[15.312,2.555],[15.13,2.467],[15.093,2.493],[15.057,2.553],[14.882,2.546],[14.879,2.394],[14.819,2.298],[14.809,1.702],[14.855,1.749],[14.851,1.503],[14.707,1.357],[13.575,1.637],[8.898,1.61],[8.887,1.62],[5.772,1.595],[5.761,1.606],[4.518,1.595],[4.475,1.615],[4.176,1.613],[4.159,1.629],[4.114,2.38],[4.147,2.367],[4.145,2.4],[4.094,2.449],[3.961,2.535],[3.639,2.532],[3.593,2.423],[3.448,2.509],[3.372,2.53],[3.243,2.529],[3.196,2.431],[3.029,2.528],[2.858,2.526],[2.799,2.439],[2.643,2.525],[2.461,2.523],[2.428,2.463],[2.402,2.446],[2.269,2.511],[2.181,2.532],[2.064,2.52],[2.016,2.454],[1.973,2.454],[1.86,2.519],[1.709,2.528],[1.7,2.517],[1.667,2.517],[1.608,2.451],[1.442,2.515],[1.27,2.514],[1.232,2.459],[1.189,2.459],[1.012,2.523],[0.904,2.522],[0.835,2.456],[0.813,2.456],[0.625,2.52],[0.507,2.519],[0.438,2.453],[0.26,2.517],[0.099,2.516],[0.05,2.461],[0.007,2.461],[-0.116,2.514],[-0.267,2.513],[-0.318,2.491],[-0.347,2.458],[-0.369,2.458],[-0.535,2.511],[-0.675,2.51],[-0.745,2.455],[-0.933,2.508],[-1.073,2.507],[-1.122,2.463],[-1.176,2.463],[-1.288,2.505],[-1.654,2.503],[-1.715,2.469],[-1.738,2.431],[-1.734,2.387],[-1.702,2.338],[-1.758,2.356],[-1.732,2.312],[-1.726,2.257],[-1.736,2.246],[-1.729,2.181]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{}}},"bounds":{"min":[6.589,-0.093,-0.72],"max":[17.202,2.55,0.72]},"volume_in3":7.1095,"centroid":[12.6094,1.1124,0],"shell":[12.1991,0.9642,0],"area_in2":97.3672,"triangles":5176,"manifold":true,"slabs":[[6.589,0.812,-0.72,6.982,1.635,0.72],[6.982,0.098,-0.72,14.057,1.635,0.72],[14.057,0.088,-0.72,14.45,1.517,0.72],[14.45,-0.093,-0.72,14.844,2.119,0.72],[14.844,-0.093,-0.72,16.416,2.55,0.72],[16.416,-0.093,-0.72,16.809,2.163,0.72],[16.809,0.235,-0.72,17.202,1.488,0.72]],"slots":["receiver"]},"panzer-ar57-ult-12-upper.receiver":{"part":"panzer-ar57-ult-12-upper","component":"receiver","model":"panzer-ar57-ult-12-upper.receiver.glb","script":"panzer_ar57_ult_upper.py","inputs":{"fn-p90-50-magazine.height":0.77,"fn-p90-50-magazine.width":1.949,"panzer-ar57-ult-12-upper.barrel_od":0.53,"panzer-ar57-ult-12-upper.barrel_rear_x":5.508,"panzer-ar57-ult-12-upper.bolt_end_d":0.75,"panzer-ar57-ult-12-upper.bolt_end_proud":0.05,"panzer-ar57-ult-12-upper.bolt_window_depth":0.3,"panzer-ar57-ult-12-upper.bolt_window_front_x":3.999,"panzer-ar57-ult-12-upper.bolt_window_rear_x":3.141,"panzer-ar57-ult-12-upper.bore_axis_above_pin":0.951,"panzer-ar57-ult-12-upper.catch_bottom_y":1.799,"panzer-ar57-ult-12-upper.catch_front_x":3.16,"panzer-ar57-ult-12-upper.catch_out":0.3,"panzer-ar57-ult-12-upper.catch_rear_x":2.9,"panzer-ar57-ult-12-upper.catch_top_y":2.185,"panzer-ar57-ult-12-upper.channel_bottom_y":0.358,"panzer-ar57-ult-12-upper.channel_depth":0.1,"panzer-ar57-ult-12-upper.channel_front_x":6.988,"panzer-ar57-ult-12-upper.channel_gap":0.03,"panzer-ar57-ult-12-upper.channel_rear_x":0.774,"panzer-ar57-ult-12-upper.channel_top_y":0.865,"panzer-ar57-ult-12-upper.cross_hole_d":0.171,"panzer-ar57-ult-12-upper.cross_hole_depth":0.1,"panzer-ar57-ult-12-upper.cross_hole_y":2.27,"panzer-ar57-ult-12-upper.feed_notch_length":1.462,"panzer-ar57-ult-12-upper.feed_pocket_d":1.883,"panzer-ar57-ult-12-upper.feed_pocket_floor_y":1.063,"panzer-ar57-ult-12-upper.feed_pocket_x":5.056,"panzer-ar57-ult-12-upper.front_block_face_x":14.951,"panzer-ar57-ult-12-upper.front_block_rear_x":14.866,"panzer-ar57-ult-12-upper.front_hole_pitch":0.2653,"panzer-ar57-ult-12-upper.front_hole_x":15.139,"panzer-ar57-ult-12-upper.front_hole_y":2.23,"panzer-ar57-ult-12-upper.front_rail_front_x":16.247,"panzer-ar57-ult-12-upper.front_rail_slot0_x":15.187,"panzer-ar57-ult-12-upper.front_rail_slots":3,"panzer-ar57-ult-12-upper.front_rail_top_above_pin":2.55,"panzer-ar57-ult-12-upper.handguard_bottom_y":0.098,"panzer-ar57-ult-12-upper.handguard_front_x":17.202,"panzer-ar57-ult-12-upper.handguard_rear_bottom_x":7.246,"panzer-ar57-ult-12-upper.handguard_rear_top_x":6.589,"panzer-ar57-ult-12-upper.handguard_wall":0.12,"panzer-ar57-ult-12-upper.handguard_width":1.44,"panzer-ar57-ult-12-upper.handle_bottom_y":0.433,"panzer-ar57-ult-12-upper.handle_front_x":6.907,"panzer-ar57-ult-12-upper.handle_out":0.2,"panzer-ar57-ult-12-upper.handle_rear_x":5.296,"panzer-ar57-ult-12-upper.handle_top_y":0.79,"panzer-ar57-ult-12-upper.keel_top_y":0.241,"panzer-ar57-ult-12-upper.keel_width":0.67,"panzer-ar57-ult-12-upper.latch_bottom_y":1.76,"panzer-ar57-ult-12-upper.latch_top_y":2.1,"panzer-ar57-ult-12-upper.latch_width":0.62,"panzer-ar57-ult-12-upper.lower_chamfer_top_y":0.649,"panzer-ar57-ult-12-upper.lower_face_angle":133.34,"panzer-ar57-ult-12-upper.lower_hole_pitch":0.3174,"panzer-ar57-ult-12-upper.lower_hole_x":15.326,"panzer-ar57-ult-12-upper.lower_hole_y":0.157,"panzer-ar57-ult-12-upper.lower_rail_bottom_y":-0.093,"panzer-ar57-ult-12-upper.lower_rail_slot0_x":15.279,"panzer-ar57-ult-12-upper.lug_clearance":0.005,"panzer-ar57-ult-12-upper.mag_rear_x":4.082,"panzer-ar57-ult-12-upper.mag_underside_y":1.635,"panzer-ar57-ult-12-upper.mlok_lower_axis_y":1.0297,"panzer-ar57-ult-12-upper.mlok_lower_face_distance":0.785,"panzer-ar57-ult-12-upper.mlok_lower_front_x":15.389,"panzer-ar57-ult-12-upper.mlok_lower_slots":5,"panzer-ar57-ult-12-upper.mlok_lower_y":0.491,"panzer-ar57-ult-12-upper.mlok_lower_z":0.5709,"panzer-ar57-ult-12-upper.mlok_upper_front_x":16.328,"panzer-ar57-ult-12-upper.mlok_upper_slots":6,"panzer-ar57-ult-12-upper.mlok_upper_y":0.984,"panzer-ar57-ult-12-upper.muzzle_end_x":19.58,"panzer-ar57-ult-12-upper.muzzle_end_x_pinframe":19.58,"panzer-ar57-ult-12-upper.rail_block_front_x":3.98,"panzer-ar57-ult-12-upper.rail_front_x":3.979,"panzer-ar57-ult-12-upper.rail_rear_x":-1.767,"panzer-ar57-ult-12-upper.rail_rear_x_pinframe":-1.767,"panzer-ar57-ult-12-upper.rail_slot0_x":-1.216,"panzer-ar57-ult-12-upper.rail_slots":13,"panzer-ar57-ult-12-upper.rail_top_above_pin":2.543,"panzer-ar57-ult-12-upper.receiver_chamfer_front_low_x":3.557,"panzer-ar57-ult-12-upper.receiver_chamfer_front_low_y":1.278,"panzer-ar57-ult-12-upper.receiver_chamfer_front_top_x":3.69,"panzer-ar57-ult-12-upper.receiver_chamfer_front_top_y":1.42,"panzer-ar57-ult-12-upper.receiver_chamfer_top_y":1.506,"panzer-ar57-ult-12-upper.receiver_rear_x":-0.621,"panzer-ar57-ult-12-upper.receiver_top_y":1.524,"panzer-ar57-ult-12-upper.riser_width":0.62,"panzer-ar57-ult-12-upper.side_face_bottom_y":0.26,"panzer-ar57-ult-12-upper.side_face_top_y":1.26,"panzer-ar57-ult-12-upper.takedown_lug_front_x":0.22,"panzer-ar57-ult-12-upper.top_flat_width":0.835,"panzer-ar57-ult-12-upper.tray_dip_rear_x":13.551,"panzer-ar57-ult-12-upper.tray_front_y":1.362,"panzer-ar57-ult-12-upper.tray_top_y":1.635,"panzer-ar57-ult-12-upper.underside_y":0.2485,"panzer-ar57-ult-12-upper.width":1.44,"panzer-ar57-ult-12-upper.window2_front_x":2.601,"panzer-ar57-ult-12-upper.window2_rear_x":2.292,"panzer-ar57-ult-12-upper.window_bottom_y":1.758,"panzer-ar57-ult-12-upper.window_front_x":3.544,"panzer-ar57-ult-12-upper.window_rear_x":2.946,"panzer-ar57-ult-12-upper.window_top_y":2.131,"std.ar15.bore_axis_y":0.8775,"std.ar15.buffer_tower_front_x":-0.628,"std.ar15.buffer_tower_od":1.392,"std.ar15.buffer_tower_top_y":1.5735,"std.ar15.buffer_trough_r":0.5625,"std.ar15.deck_y":0.2485,"std.ar15.front_lug_slot_width":0.5,"std.ar15.pin_spacing":6.375,"std.ar15.rear_lug_slot_rear_x":-0.402,"std.ar15.rear_lug_slot_width":0.5,"std.ar15.rear_wall_arc_r":0.75,"std.mlok.slot_corner_r":0.0937007874015748,"std.mlok.slot_length":1.2598425196850394,"std.mlok.slot_pitch":1.574803149606299,"std.mlok.slot_width":0.2755905511811024,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{"side":[[-1.767,2.126],[-1.749,2.06],[-1.66,1.979],[-1.525,1.925],[-1.383,1.905],[-1.218,1.863],[-1.081,1.787],[-1.028,1.739],[-0.976,1.652],[-0.947,1.625],[-0.66,1.529],[-0.509,1.498],[-0.47,1.472],[-0.527,1.408],[-0.58,1.301],[-0.573,1.121],[-0.583,1.11],[-0.574,1.025],[-0.584,1.015],[-0.569,0.856],[-0.821,0.918],[-0.8,0.811],[-0.758,0.703],[-0.658,0.554],[-0.534,0.432],[-0.421,0.358],[-0.331,0.316],[-0.277,0.306],[-0.237,0.279],[-0.217,-0.167],[-0.177,-0.204],[-0.1,-0.225],[0.367,-0.22],[0.378,-0.231],[0.439,-0.199],[0.453,-0.172],[0.45,-0.023],[0.46,-0.013],[0.446,0.147],[0.453,0.189],[0.477,0.216],[0.807,0.219],[0.819,0.209],[1.722,0.217],[1.734,0.206],[3.454,0.221],[3.466,0.211],[4.272,0.218],[4.283,0.207],[6.137,0.213],[6.153,0.197],[6.164,-0.036],[6.189,-0.11],[6.261,-0.189],[6.368,-0.23],[6.516,-0.218],[6.846,-0.056],[7.17,0.042],[7.244,0.042],[7.254,0.053],[7.375,0.044],[7.385,0.054],[8.1,0.061],[8.111,0.05],[10.913,0.065],[10.923,0.054],[12.065,0.064],[12.075,0.054],[12.201,0.065],[12.211,0.055],[14.009,0.061],[14.019,0.05],[14.218,0.062],[14.228,0.052],[14.437,0.043],[14.563,0.003],[14.832,-0.12],[14.935,-0.151],[15.352,-0.137],[15.394,-0.157],[15.456,-0.157],[15.467,-0.146],[15.55,-0.145],[15.561,-0.135],[15.717,-0.133],[15.748,-0.154],[15.841,-0.153],[15.852,-0.143],[16.05,-0.13],[16.06,-0.141],[16.112,-0.14],[16.143,-0.161],[16.175,-0.15],[16.31,-0.149],[16.321,-0.138],[16.582,-0.145],[16.677,-0.053],[16.701,-0.011],[16.706,0.064],[16.767,0.183],[17.047,0.527],[17.202,0.528],[17.202,1.158],[17.151,1.158],[17.11,1.178],[17.079,1.178],[17.014,1.256],[16.988,1.309],[16.931,1.332],[16.869,1.391],[16.761,1.565],[16.657,1.819],[16.558,2.011],[16.381,2.2],[16.371,2.233],[16.331,2.288],[16.302,2.343],[16.291,2.448],[16.245,2.508],[16.183,2.551],[16.066,2.55],[15.905,2.473],[15.869,2.532],[15.843,2.548],[15.705,2.547],[15.512,2.469],[15.487,2.518],[15.44,2.556],[15.312,2.555],[15.13,2.467],[15.093,2.493],[15.057,2.553],[14.882,2.546],[14.879,2.394],[14.819,2.298],[14.809,1.702],[14.855,1.749],[14.851,1.503],[14.707,1.357],[13.575,1.637],[8.898,1.61],[8.887,1.62],[5.772,1.595],[5.761,1.606],[4.518,1.595],[4.475,1.615],[4.176,1.613],[4.159,1.629],[4.114,2.38],[4.147,2.367],[4.145,2.4],[4.094,2.449],[3.961,2.535],[3.639,2.532],[3.593,2.423],[3.448,2.509],[3.372,2.53],[3.243,2.529],[3.196,2.431],[3.029,2.528],[2.858,2.526],[2.799,2.439],[2.643,2.525],[2.461,2.523],[2.428,2.463],[2.402,2.446],[2.269,2.511],[2.181,2.532],[2.064,2.52],[2.016,2.454],[1.973,2.454],[1.86,2.519],[1.709,2.528],[1.7,2.517],[1.667,2.517],[1.608,2.451],[1.442,2.515],[1.27,2.514],[1.232,2.459],[1.189,2.459],[1.012,2.523],[0.904,2.522],[0.835,2.456],[0.813,2.456],[0.625,2.52],[0.507,2.519],[0.438,2.453],[0.26,2.517],[0.099,2.516],[0.05,2.461],[0.007,2.461],[-0.116,2.514],[-0.267,2.513],[-0.318,2.491],[-0.347,2.458],[-0.369,2.458],[-0.535,2.511],[-0.675,2.51],[-0.745,2.455],[-0.933,2.508],[-1.073,2.507],[-1.122,2.463],[-1.176,2.463],[-1.288,2.505],[-1.654,2.503],[-1.715,2.469],[-1.738,2.431],[-1.734,2.387],[-1.702,2.338],[-1.758,2.356],[-1.732,2.312],[-1.726,2.257],[-1.736,2.246],[-1.729,2.181]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{}}},"bounds":{"min":[-1.767,-0.23,-0.72],"max":[7.3234,2.425,0.92]},"volume_in3":15.8774,"centroid":[2.6954,1.0611,-0.0011],"shell":[3.0297,1.077,0.0725],"area_in2":77.7301,"triangles":3990,"manifold":true,"rear_corner":{"r":0.75,"centre":[0.122,0.9985],"x":[-0.628,-0.0116],"reach_z":0.696,"trough_r":0.5625},"slabs":[[-1.767,1.902,-0.31,-1.372,2.425,0.31],[-1.372,1.653,-0.31,-0.977,2.425,0.31],[-0.977,0.352,-0.72,-0.581,2.425,0.72],[-0.581,-0.225,-0.72,0.604,2.425,0.72],[0.604,0.248,-0.72,4.162,2.425,0.72],[4.162,0.249,-0.72,4.557,1.635,0.72],[4.557,0.249,-0.72,4.952,1.063,0.72],[4.952,0.249,-0.72,5.742,1.063,0.92],[5.742,0.249,-0.72,6.138,1.635,0.92],[6.138,-0.23,-0.72,6.928,1.635,0.92],[6.928,-0.017,-0.72,7.323,0.925,0.72]],"slots":["receiver","bolt"]},"panzer-ar57-ult-16-upper.barrel":{"part":"panzer-ar57-ult-16-upper","component":"barrel","model":"panzer-ar57-ult-16-upper.barrel.glb","script":"panzer_ar57_ult_upper.py","inputs":{"fn-p90-50-magazine.height":0.77,"fn-p90-50-magazine.width":1.949,"panzer-ar57-ult-16-upper.barrel_od":0.53,"panzer-ar57-ult-16-upper.barrel_rear_x":5.508,"panzer-ar57-ult-16-upper.bolt_end_d":0.75,"panzer-ar57-ult-16-upper.bolt_end_proud":0.05,"panzer-ar57-ult-16-upper.bolt_window_depth":0.3,"panzer-ar57-ult-16-upper.bolt_window_front_x":3.8,"panzer-ar57-ult-16-upper.bolt_window_rear_x":3.03,"panzer-ar57-ult-16-upper.bore_axis_above_pin":0.957,"panzer-ar57-ult-16-upper.bore_d":0.224,"panzer-ar57-ult-16-upper.brake_band_front_x":21.88,"panzer-ar57-ult-16-upper.brake_bore_d":0.24,"panzer-ar57-ult-16-upper.brake_groove_depth":0.02,"panzer-ar57-ult-16-upper.brake_groove_w":0.03,"panzer-ar57-ult-16-upper.brake_od":0.59,"panzer-ar57-ult-16-upper.brake_port_columns":3,"panzer-ar57-ult-16-upper.brake_port_d":0.171,"panzer-ar57-ult-16-upper.brake_port_phase":17,"panzer-ar57-ult-16-upper.brake_port_pitch":0.25,"panzer-ar57-ult-16-upper.brake_port_x":22.32,"panzer-ar57-ult-16-upper.brake_ports_around":6,"panzer-ar57-ult-16-upper.brake_rear_x":21.38,"panzer-ar57-ult-16-upper.brake_slot_depth":0.43,"panzer-ar57-ult-16-upper.brake_slot_width":0.226,"panzer-ar57-ult-16-upper.catch_bottom_y":1.77,"panzer-ar57-ult-16-upper.catch_front_x":3.16,"panzer-ar57-ult-16-upper.catch_out":0.3,"panzer-ar57-ult-16-upper.catch_rear_x":2.93,"panzer-ar57-ult-16-upper.catch_top_y":2.14,"panzer-ar57-ult-16-upper.channel_bottom_y":0.46,"panzer-ar57-ult-16-upper.channel_depth":0.1,"panzer-ar57-ult-16-upper.channel_front_x":6.83,"panzer-ar57-ult-16-upper.channel_gap":0.03,"panzer-ar57-ult-16-upper.channel_rear_x":0.57,"panzer-ar57-ult-16-upper.channel_top_y":1,"panzer-ar57-ult-16-upper.cross_hole_d":0.125,"panzer-ar57-ult-16-upper.cross_hole_depth":0.1,"panzer-ar57-ult-16-upper.cross_hole_y":2.26,"panzer-ar57-ult-16-upper.feed_notch_length":1.52,"panzer-ar57-ult-16-upper.feed_pocket_d":1.883,"panzer-ar57-ult-16-upper.feed_pocket_floor_y":1.055,"panzer-ar57-ult-16-upper.feed_pocket_x":5.045,"panzer-ar57-ult-16-upper.front_block_face_x":14.939,"panzer-ar57-ult-16-upper.front_block_rear_x":15,"panzer-ar57-ult-16-upper.front_hole_pitch":0.269,"panzer-ar57-ult-16-upper.front_hole_x":15.19,"panzer-ar57-ult-16-upper.front_hole_y":2.22,"panzer-ar57-ult-16-upper.front_rail_front_x":16.32,"panzer-ar57-ult-16-upper.front_rail_slot0_x":15.282,"panzer-ar57-ult-16-upper.front_rail_slots":3,"panzer-ar57-ult-16-upper.front_rail_top_above_pin":2.54,"panzer-ar57-ult-16-upper.handguard_bottom_y":0.098,"panzer-ar57-ult-16-upper.handguard_front_x":17.12,"panzer-ar57-ult-16-upper.handguard_rear_bottom_x":7.26,"panzer-ar57-ult-16-upper.handguard_rear_top_x":6.51,"panzer-ar57-ult-16-upper.handguard_wall":0.12,"panzer-ar57-ult-16-upper.handguard_width":1.44,"panzer-ar57-ult-16-upper.handle_bottom_y":0.67,"panzer-ar57-ult-16-upper.handle_front_x":6.74,"panzer-ar57-ult-16-upper.handle_out":0.2,"panzer-ar57-ult-16-upper.handle_rear_x":5,"panzer-ar57-ult-16-upper.handle_top_y":0.99,"panzer-ar57-ult-16-upper.keel_top_y":0.259,"panzer-ar57-ult-16-upper.keel_width":0.67,"panzer-ar57-ult-16-upper.latch_bottom_y":1.78,"panzer-ar57-ult-16-upper.latch_top_y":2.12,"panzer-ar57-ult-16-upper.latch_width":0.62,"panzer-ar57-ult-16-upper.lower_chamfer_top_y":0.665,"panzer-ar57-ult-16-upper.lower_face_angle":133.48,"panzer-ar57-ult-16-upper.lower_hole_pitch":0.308,"panzer-ar57-ult-16-upper.lower_hole_x":15.33,"panzer-ar57-ult-16-upper.lower_hole_y":0.186,"panzer-ar57-ult-16-upper.lower_rail_bottom_y":-0.093,"panzer-ar57-ult-16-upper.lower_rail_slot0_x":15.51,"panzer-ar57-ult-16-upper.lug_clearance":0.005,"panzer-ar57-ult-16-upper.mag_rear_x":4.07,"panzer-ar57-ult-16-upper.mag_underside_y":1.6,"panzer-ar57-ult-16-upper.mlok_lower_axis_y":1.0458,"panzer-ar57-ult-16-upper.mlok_lower_face_distance":0.7845,"panzer-ar57-ult-16-upper.mlok_lower_front_x":15.5,"panzer-ar57-ult-16-upper.mlok_lower_slots":5,"panzer-ar57-ult-16-upper.mlok_lower_y":0.506,"panzer-ar57-ult-16-upper.mlok_lower_z":0.5692,"panzer-ar57-ult-16-upper.mlok_upper_front_x":16.32,"panzer-ar57-ult-16-upper.mlok_upper_slots":6,"panzer-ar57-ult-16-upper.mlok_upper_y":1.005,"panzer-ar57-ult-16-upper.muzzle_end_x":23.508,"panzer-ar57-ult-16-upper.muzzle_end_x_pinframe":23.325,"panzer-ar57-ult-16-upper.plate_notch_front_x":3.47,"panzer-ar57-ult-16-upper.plate_notch_rear_x":2.97,"panzer-ar57-ult-16-upper.plate_notch_top_y":0.777,"panzer-ar57-ult-16-upper.plate_screw_d":0.21,"panzer-ar57-ult-16-upper.plate_screw_front_x":6.43,"panzer-ar57-ult-16-upper.plate_screw_mid_x":2.78,"panzer-ar57-ult-16-upper.plate_screw_rear_x":0.94,"panzer-ar57-ult-16-upper.plate_screw_y":0.64,"panzer-ar57-ult-16-upper.rail_block_front_x":3.97,"panzer-ar57-ult-16-upper.rail_front_x":3.978,"panzer-ar57-ult-16-upper.rail_rear_x":-1.723,"panzer-ar57-ult-16-upper.rail_rear_x_pinframe":-1.723,"panzer-ar57-ult-16-upper.rail_slot0_x":-1.248,"panzer-ar57-ult-16-upper.rail_slots":13,"panzer-ar57-ult-16-upper.rail_top_above_pin":2.545,"panzer-ar57-ult-16-upper.receiver_chamfer_front_low_x":3.5,"panzer-ar57-ult-16-upper.receiver_chamfer_front_low_y":1.319,"panzer-ar57-ult-16-upper.receiver_chamfer_front_top_x":3.7,"panzer-ar57-ult-16-upper.receiver_chamfer_front_top_y":1.494,"panzer-ar57-ult-16-upper.receiver_chamfer_top_y":1.525,"panzer-ar57-ult-16-upper.receiver_rear_x":-0.621,"panzer-ar57-ult-16-upper.receiver_top_y":1.59,"panzer-ar57-ult-16-upper.riser_width":0.62,"panzer-ar57-ult-16-upper.side_face_bottom_y":0.33,"panzer-ar57-ult-16-upper.side_face_top_y":1.3,"panzer-ar57-ult-16-upper.takedown_lug_front_x":0.22,"panzer-ar57-ult-16-upper.top_flat_width":0.835,"panzer-ar57-ult-16-upper.tray_dip_rear_x":13.6,"panzer-ar57-ult-16-upper.tray_front_y":1.367,"panzer-ar57-ult-16-upper.tray_top_y":1.6,"panzer-ar57-ult-16-upper.underside_y":0.2485,"panzer-ar57-ult-16-upper.width":1.44,"panzer-ar57-ult-16-upper.window2_front_x":2.585,"panzer-ar57-ult-16-upper.window2_rear_x":2.298,"panzer-ar57-ult-16-upper.window_bottom_y":1.741,"panzer-ar57-ult-16-upper.window_front_x":3.546,"panzer-ar57-ult-16-upper.window_rear_x":2.922,"panzer-ar57-ult-16-upper.window_top_y":2.127,"std.ar15.bore_axis_y":0.8775,"std.ar15.buffer_tower_front_x":-0.628,"std.ar15.buffer_tower_od":1.392,"std.ar15.buffer_tower_top_y":1.5735,"std.ar15.buffer_trough_r":0.5625,"std.ar15.deck_y":0.2485,"std.ar15.front_lug_slot_width":0.5,"std.ar15.pin_spacing":6.375,"std.ar15.rear_lug_slot_rear_x":-0.402,"std.ar15.rear_lug_slot_width":0.5,"std.ar15.rear_wall_arc_r":0.75,"std.mlok.slot_corner_r":0.0937007874015748,"std.mlok.slot_length":1.2598425196850394,"std.mlok.slot_pitch":1.574803149606299,"std.mlok.slot_width":0.2755905511811024,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{"side":[[-1.723,2.131],[-1.71,2.118],[-1.71,2.069],[-1.642,2],[-1.567,1.962],[-1.492,1.937],[-1.442,1.937],[-1.43,1.925],[-1.38,1.925],[-1.318,1.9],[-1.218,1.887],[-1.106,1.837],[-0.975,1.706],[-0.919,1.6],[-0.894,1.588],[-0.67,1.588],[-0.651,1.569],[-0.651,1.494],[-0.676,1.432],[-0.676,1.382],[-0.688,1.37],[-0.688,1.27],[-0.689,0.771],[-0.676,0.759],[-0.677,0.659],[-0.664,0.646],[-0.652,0.547],[-0.627,0.497],[-0.583,0.453],[-0.446,0.44],[-0.228,0.284],[-0.228,-0.152],[-0.185,-0.196],[-0.147,-0.208],[-0.11,-0.208],[-0.097,-0.221],[0.164,-0.221],[0.177,-0.208],[0.252,-0.196],[0.289,-0.171],[0.295,-0.015],[0.308,-0.003],[0.308,0.222],[0.327,0.24],[0.551,0.24],[0.564,0.253],[1.013,0.24],[1.761,0.239],[1.773,0.252],[1.836,0.252],[2.085,0.251],[2.097,0.239],[2.16,0.239],[2.172,0.251],[2.21,0.239],[2.247,0.239],[2.259,0.251],[2.808,0.251],[2.82,0.238],[2.858,0.238],[2.933,0.238],[2.945,0.251],[6.137,0.248],[6.156,0.23],[6.155,-0.082],[6.193,-0.144],[6.236,-0.188],[6.311,-0.226],[6.374,-0.238],[6.386,-0.226],[6.436,-0.226],[6.648,-0.114],[6.673,-0.114],[6.698,-0.089],[6.723,-0.089],[6.76,-0.064],[6.785,-0.064],[6.885,-0.014],[6.922,-0.014],[6.997,0.023],[7.035,0.023],[7.097,0.048],[7.147,0.048],[7.159,0.06],[7.222,0.06],[7.234,0.073],[7.346,0.073],[7.359,0.085],[14.541,0.092],[15.139,-0.12],[15.301,-0.12],[15.313,-0.108],[15.351,-0.108],[15.37,-0.064],[15.37,-0.015],[15.388,0.004],[15.426,0.004],[15.444,-0.015],[15.457,-0.077],[15.5,-0.108],[15.725,-0.108],[15.744,-0.09],[15.744,-0.04],[15.775,0.016],[15.831,-0.027],[15.843,-0.09],[15.887,-0.108],[16.099,-0.109],[16.13,-0.09],[16.13,-0.04],[16.161,0.016],[16.205,-0.015],[16.217,-0.09],[16.236,-0.109],[16.548,-0.109],[16.616,-0.028],[16.666,0.084],[16.666,0.109],[16.766,0.284],[16.829,0.346],[16.866,0.408],[16.953,0.508],[17.003,0.595],[17.05,0.642],[17.05,1.225],[17.023,1.225],[17.004,1.243],[16.979,1.293],[16.917,1.356],[16.817,1.505],[16.767,1.555],[16.518,2.004],[16.381,2.179],[16.344,2.266],[16.307,2.316],[16.269,2.429],[16.219,2.503],[16.176,2.535],[16.088,2.535],[16.076,2.522],[15.976,2.51],[15.958,2.491],[15.957,2.441],[15.914,2.41],[15.883,2.454],[15.883,2.516],[15.864,2.535],[15.689,2.535],[15.59,2.498],[15.571,2.429],[15.552,2.41],[15.527,2.41],[15.509,2.429],[15.496,2.516],[15.478,2.535],[15.303,2.535],[15.291,2.523],[15.216,2.51],[15.197,2.467],[15.197,2.429],[15.166,2.411],[15.122,2.442],[15.11,2.504],[15.079,2.535],[14.954,2.536],[14.947,1.382],[14.928,1.364],[14.192,1.364],[13.98,1.364],[13.793,1.427],[13.694,1.477],[13.631,1.489],[13.588,1.52],[13.607,1.539],[13.681,1.539],[13.706,1.552],[13.713,1.558],[13.694,1.576],[4.056,1.584],[4.037,1.603],[4.038,2.114],[4.025,2.126],[4.038,2.139],[4.025,2.326],[4.038,2.338],[4.038,2.476],[3.932,2.544],[3.62,2.544],[3.602,2.526],[3.602,2.463],[3.57,2.432],[3.483,2.432],[3.452,2.451],[3.452,2.501],[3.421,2.532],[3.383,2.545],[3.221,2.545],[3.203,2.501],[3.203,2.451],[3.184,2.433],[3.159,2.433],[3.084,2.433],[3.065,2.451],[3.065,2.501],[3.034,2.532],[2.997,2.545],[2.835,2.545],[2.804,2.501],[2.804,2.452],[2.785,2.433],[2.747,2.433],[2.735,2.42],[2.679,2.452],[2.679,2.502],[2.66,2.52],[2.598,2.545],[2.436,2.545],[2.417,2.527],[2.417,2.464],[2.386,2.433],[2.348,2.433],[2.336,2.421],[2.292,2.452],[2.292,2.502],[2.249,2.533],[2.211,2.546],[2.037,2.546],[2.018,2.527],[2.018,2.452],[1.974,2.421],[1.937,2.421],[1.906,2.452],[1.906,2.502],[1.887,2.521],[1.812,2.546],[1.65,2.546],[1.632,2.527],[1.619,2.452],[1.588,2.421],[1.563,2.421],[1.519,2.453],[1.519,2.502],[1.501,2.521],[1.426,2.546],[1.251,2.546],[1.233,2.528],[1.233,2.478],[1.22,2.453],[1.189,2.422],[1.151,2.422],[1.133,2.44],[1.133,2.478],[1.114,2.521],[1.077,2.521],[1.027,2.546],[0.865,2.547],[0.834,2.503],[0.834,2.453],[0.802,2.422],[0.765,2.422],[0.746,2.441],[0.746,2.491],[0.728,2.522],[0.628,2.534],[0.615,2.547],[0.478,2.547],[0.447,2.528],[0.435,2.441],[0.416,2.422],[0.378,2.422],[0.36,2.441],[0.36,2.491],[0.329,2.522],[0.241,2.535],[0.229,2.547],[0.079,2.547],[0.048,2.504],[0.048,2.441],[0.029,2.423],[0.004,2.423],[-0.027,2.441],[-0.027,2.491],[-0.058,2.522],[-0.095,2.522],[-0.158,2.547],[-0.32,2.548],[-0.338,2.529],[-0.351,2.442],[-0.382,2.423],[-0.413,2.442],[-0.413,2.491],[-0.438,2.516],[-0.494,2.535],[-0.557,2.535],[-0.569,2.548],[-0.681,2.548],[-0.719,2.535],[-0.737,2.504],[-0.737,2.442],[-0.756,2.423],[-0.781,2.423],[-0.8,2.442],[-0.8,2.504],[-0.831,2.523],[-0.943,2.536],[-0.956,2.548],[-1.093,2.548],[-1.124,2.529],[-1.136,2.442],[-1.155,2.423],[-1.186,2.442],[-1.186,2.492],[-1.217,2.523],[-1.28,2.523],[-1.292,2.536],[-1.666,2.536],[-1.691,2.524],[-1.722,2.492],[-1.722,2.393],[-1.71,2.38],[-1.71,2.281],[-1.698,2.268],[-1.71,2.256],[-1.71,2.143]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{}}},"bounds":{"min":[5.508,0.662,-0.295],"max":[23.508,1.252,0.295]},"volume_in3":3.2233,"centroid":[14.3871,0.957,0],"shell":[14.7412,0.957,0],"area_in2":44.2938,"triangles":4508,"manifold":true,"slabs":[[5.508,0.662,-0.295,23.508,1.252,0.295]],"slots":["barrel"]},"panzer-ar57-ult-16-upper.handguard":{"part":"panzer-ar57-ult-16-upper","component":"handguard","model":"panzer-ar57-ult-16-upper.handguard.glb","script":"panzer_ar57_ult_upper.py","inputs":{"fn-p90-50-magazine.height":0.77,"fn-p90-50-magazine.width":1.949,"panzer-ar57-ult-16-upper.barrel_od":0.53,"panzer-ar57-ult-16-upper.barrel_rear_x":5.508,"panzer-ar57-ult-16-upper.bolt_end_d":0.75,"panzer-ar57-ult-16-upper.bolt_end_proud":0.05,"panzer-ar57-ult-16-upper.bolt_window_depth":0.3,"panzer-ar57-ult-16-upper.bolt_window_front_x":3.8,"panzer-ar57-ult-16-upper.bolt_window_rear_x":3.03,"panzer-ar57-ult-16-upper.bore_axis_above_pin":0.957,"panzer-ar57-ult-16-upper.catch_bottom_y":1.77,"panzer-ar57-ult-16-upper.catch_front_x":3.16,"panzer-ar57-ult-16-upper.catch_out":0.3,"panzer-ar57-ult-16-upper.catch_rear_x":2.93,"panzer-ar57-ult-16-upper.catch_top_y":2.14,"panzer-ar57-ult-16-upper.channel_bottom_y":0.46,"panzer-ar57-ult-16-upper.channel_depth":0.1,"panzer-ar57-ult-16-upper.channel_front_x":6.83,"panzer-ar57-ult-16-upper.channel_gap":0.03,"panzer-ar57-ult-16-upper.channel_rear_x":0.57,"panzer-ar57-ult-16-upper.channel_top_y":1,"panzer-ar57-ult-16-upper.cross_hole_d":0.125,"panzer-ar57-ult-16-upper.cross_hole_depth":0.1,"panzer-ar57-ult-16-upper.cross_hole_y":2.26,"panzer-ar57-ult-16-upper.feed_notch_length":1.52,"panzer-ar57-ult-16-upper.feed_pocket_d":1.883,"panzer-ar57-ult-16-upper.feed_pocket_floor_y":1.055,"panzer-ar57-ult-16-upper.feed_pocket_x":5.045,"panzer-ar57-ult-16-upper.front_block_face_x":14.939,"panzer-ar57-ult-16-upper.front_block_rear_x":15,"panzer-ar57-ult-16-upper.front_hole_pitch":0.269,"panzer-ar57-ult-16-upper.front_hole_x":15.19,"panzer-ar57-ult-16-upper.front_hole_y":2.22,"panzer-ar57-ult-16-upper.front_rail_front_x":16.32,"panzer-ar57-ult-16-upper.front_rail_slot0_x":15.282,"panzer-ar57-ult-16-upper.front_rail_slots":3,"panzer-ar57-ult-16-upper.front_rail_top_above_pin":2.54,"panzer-ar57-ult-16-upper.handguard_bottom_y":0.098,"panzer-ar57-ult-16-upper.handguard_front_x":17.12,"panzer-ar57-ult-16-upper.handguard_rear_bottom_x":7.26,"panzer-ar57-ult-16-upper.handguard_rear_top_x":6.51,"panzer-ar57-ult-16-upper.handguard_wall":0.12,"panzer-ar57-ult-16-upper.handguard_width":1.44,"panzer-ar57-ult-16-upper.handle_bottom_y":0.67,"panzer-ar57-ult-16-upper.handle_front_x":6.74,"panzer-ar57-ult-16-upper.handle_out":0.2,"panzer-ar57-ult-16-upper.handle_rear_x":5,"panzer-ar57-ult-16-upper.handle_top_y":0.99,"panzer-ar57-ult-16-upper.keel_top_y":0.259,"panzer-ar57-ult-16-upper.keel_width":0.67,"panzer-ar57-ult-16-upper.latch_bottom_y":1.78,"panzer-ar57-ult-16-upper.latch_top_y":2.12,"panzer-ar57-ult-16-upper.latch_width":0.62,"panzer-ar57-ult-16-upper.lower_chamfer_top_y":0.665,"panzer-ar57-ult-16-upper.lower_face_angle":133.48,"panzer-ar57-ult-16-upper.lower_hole_pitch":0.308,"panzer-ar57-ult-16-upper.lower_hole_x":15.33,"panzer-ar57-ult-16-upper.lower_hole_y":0.186,"panzer-ar57-ult-16-upper.lower_rail_bottom_y":-0.093,"panzer-ar57-ult-16-upper.lower_rail_slot0_x":15.51,"panzer-ar57-ult-16-upper.lug_clearance":0.005,"panzer-ar57-ult-16-upper.mag_rear_x":4.07,"panzer-ar57-ult-16-upper.mag_underside_y":1.6,"panzer-ar57-ult-16-upper.mlok_lower_axis_y":1.0458,"panzer-ar57-ult-16-upper.mlok_lower_face_distance":0.7845,"panzer-ar57-ult-16-upper.mlok_lower_front_x":15.5,"panzer-ar57-ult-16-upper.mlok_lower_slots":5,"panzer-ar57-ult-16-upper.mlok_lower_y":0.506,"panzer-ar57-ult-16-upper.mlok_lower_z":0.5692,"panzer-ar57-ult-16-upper.mlok_upper_front_x":16.32,"panzer-ar57-ult-16-upper.mlok_upper_slots":6,"panzer-ar57-ult-16-upper.mlok_upper_y":1.005,"panzer-ar57-ult-16-upper.muzzle_end_x":23.508,"panzer-ar57-ult-16-upper.muzzle_end_x_pinframe":23.325,"panzer-ar57-ult-16-upper.plate_notch_front_x":3.47,"panzer-ar57-ult-16-upper.plate_notch_rear_x":2.97,"panzer-ar57-ult-16-upper.plate_notch_top_y":0.777,"panzer-ar57-ult-16-upper.plate_screw_d":0.21,"panzer-ar57-ult-16-upper.plate_screw_front_x":6.43,"panzer-ar57-ult-16-upper.plate_screw_mid_x":2.78,"panzer-ar57-ult-16-upper.plate_screw_rear_x":0.94,"panzer-ar57-ult-16-upper.plate_screw_y":0.64,"panzer-ar57-ult-16-upper.rail_block_front_x":3.97,"panzer-ar57-ult-16-upper.rail_front_x":3.978,"panzer-ar57-ult-16-upper.rail_rear_x":-1.723,"panzer-ar57-ult-16-upper.rail_rear_x_pinframe":-1.723,"panzer-ar57-ult-16-upper.rail_slot0_x":-1.248,"panzer-ar57-ult-16-upper.rail_slots":13,"panzer-ar57-ult-16-upper.rail_top_above_pin":2.545,"panzer-ar57-ult-16-upper.receiver_chamfer_front_low_x":3.5,"panzer-ar57-ult-16-upper.receiver_chamfer_front_low_y":1.319,"panzer-ar57-ult-16-upper.receiver_chamfer_front_top_x":3.7,"panzer-ar57-ult-16-upper.receiver_chamfer_front_top_y":1.494,"panzer-ar57-ult-16-upper.receiver_chamfer_top_y":1.525,"panzer-ar57-ult-16-upper.receiver_rear_x":-0.621,"panzer-ar57-ult-16-upper.receiver_top_y":1.59,"panzer-ar57-ult-16-upper.riser_width":0.62,"panzer-ar57-ult-16-upper.side_face_bottom_y":0.33,"panzer-ar57-ult-16-upper.side_face_top_y":1.3,"panzer-ar57-ult-16-upper.takedown_lug_front_x":0.22,"panzer-ar57-ult-16-upper.top_flat_width":0.835,"panzer-ar57-ult-16-upper.tray_dip_rear_x":13.6,"panzer-ar57-ult-16-upper.tray_front_y":1.367,"panzer-ar57-ult-16-upper.tray_top_y":1.6,"panzer-ar57-ult-16-upper.underside_y":0.2485,"panzer-ar57-ult-16-upper.width":1.44,"panzer-ar57-ult-16-upper.window2_front_x":2.585,"panzer-ar57-ult-16-upper.window2_rear_x":2.298,"panzer-ar57-ult-16-upper.window_bottom_y":1.741,"panzer-ar57-ult-16-upper.window_front_x":3.546,"panzer-ar57-ult-16-upper.window_rear_x":2.922,"panzer-ar57-ult-16-upper.window_top_y":2.127,"std.ar15.bore_axis_y":0.8775,"std.ar15.buffer_tower_front_x":-0.628,"std.ar15.buffer_tower_od":1.392,"std.ar15.buffer_tower_top_y":1.5735,"std.ar15.buffer_trough_r":0.5625,"std.ar15.deck_y":0.2485,"std.ar15.front_lug_slot_width":0.5,"std.ar15.pin_spacing":6.375,"std.ar15.rear_lug_slot_rear_x":-0.402,"std.ar15.rear_lug_slot_width":0.5,"std.ar15.rear_wall_arc_r":0.75,"std.mlok.slot_corner_r":0.0937007874015748,"std.mlok.slot_length":1.2598425196850394,"std.mlok.slot_pitch":1.574803149606299,"std.mlok.slot_width":0.2755905511811024,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{"side":[[-1.723,2.131],[-1.71,2.118],[-1.71,2.069],[-1.642,2],[-1.567,1.962],[-1.492,1.937],[-1.442,1.937],[-1.43,1.925],[-1.38,1.925],[-1.318,1.9],[-1.218,1.887],[-1.106,1.837],[-0.975,1.706],[-0.919,1.6],[-0.894,1.588],[-0.67,1.588],[-0.651,1.569],[-0.651,1.494],[-0.676,1.432],[-0.676,1.382],[-0.688,1.37],[-0.688,1.27],[-0.689,0.771],[-0.676,0.759],[-0.677,0.659],[-0.664,0.646],[-0.652,0.547],[-0.627,0.497],[-0.583,0.453],[-0.446,0.44],[-0.228,0.284],[-0.228,-0.152],[-0.185,-0.196],[-0.147,-0.208],[-0.11,-0.208],[-0.097,-0.221],[0.164,-0.221],[0.177,-0.208],[0.252,-0.196],[0.289,-0.171],[0.295,-0.015],[0.308,-0.003],[0.308,0.222],[0.327,0.24],[0.551,0.24],[0.564,0.253],[1.013,0.24],[1.761,0.239],[1.773,0.252],[1.836,0.252],[2.085,0.251],[2.097,0.239],[2.16,0.239],[2.172,0.251],[2.21,0.239],[2.247,0.239],[2.259,0.251],[2.808,0.251],[2.82,0.238],[2.858,0.238],[2.933,0.238],[2.945,0.251],[6.137,0.248],[6.156,0.23],[6.155,-0.082],[6.193,-0.144],[6.236,-0.188],[6.311,-0.226],[6.374,-0.238],[6.386,-0.226],[6.436,-0.226],[6.648,-0.114],[6.673,-0.114],[6.698,-0.089],[6.723,-0.089],[6.76,-0.064],[6.785,-0.064],[6.885,-0.014],[6.922,-0.014],[6.997,0.023],[7.035,0.023],[7.097,0.048],[7.147,0.048],[7.159,0.06],[7.222,0.06],[7.234,0.073],[7.346,0.073],[7.359,0.085],[14.541,0.092],[15.139,-0.12],[15.301,-0.12],[15.313,-0.108],[15.351,-0.108],[15.37,-0.064],[15.37,-0.015],[15.388,0.004],[15.426,0.004],[15.444,-0.015],[15.457,-0.077],[15.5,-0.108],[15.725,-0.108],[15.744,-0.09],[15.744,-0.04],[15.775,0.016],[15.831,-0.027],[15.843,-0.09],[15.887,-0.108],[16.099,-0.109],[16.13,-0.09],[16.13,-0.04],[16.161,0.016],[16.205,-0.015],[16.217,-0.09],[16.236,-0.109],[16.548,-0.109],[16.616,-0.028],[16.666,0.084],[16.666,0.109],[16.766,0.284],[16.829,0.346],[16.866,0.408],[16.953,0.508],[17.003,0.595],[17.05,0.642],[17.05,1.225],[17.023,1.225],[17.004,1.243],[16.979,1.293],[16.917,1.356],[16.817,1.505],[16.767,1.555],[16.518,2.004],[16.381,2.179],[16.344,2.266],[16.307,2.316],[16.269,2.429],[16.219,2.503],[16.176,2.535],[16.088,2.535],[16.076,2.522],[15.976,2.51],[15.958,2.491],[15.957,2.441],[15.914,2.41],[15.883,2.454],[15.883,2.516],[15.864,2.535],[15.689,2.535],[15.59,2.498],[15.571,2.429],[15.552,2.41],[15.527,2.41],[15.509,2.429],[15.496,2.516],[15.478,2.535],[15.303,2.535],[15.291,2.523],[15.216,2.51],[15.197,2.467],[15.197,2.429],[15.166,2.411],[15.122,2.442],[15.11,2.504],[15.079,2.535],[14.954,2.536],[14.947,1.382],[14.928,1.364],[14.192,1.364],[13.98,1.364],[13.793,1.427],[13.694,1.477],[13.631,1.489],[13.588,1.52],[13.607,1.539],[13.681,1.539],[13.706,1.552],[13.713,1.558],[13.694,1.576],[4.056,1.584],[4.037,1.603],[4.038,2.114],[4.025,2.126],[4.038,2.139],[4.025,2.326],[4.038,2.338],[4.038,2.476],[3.932,2.544],[3.62,2.544],[3.602,2.526],[3.602,2.463],[3.57,2.432],[3.483,2.432],[3.452,2.451],[3.452,2.501],[3.421,2.532],[3.383,2.545],[3.221,2.545],[3.203,2.501],[3.203,2.451],[3.184,2.433],[3.159,2.433],[3.084,2.433],[3.065,2.451],[3.065,2.501],[3.034,2.532],[2.997,2.545],[2.835,2.545],[2.804,2.501],[2.804,2.452],[2.785,2.433],[2.747,2.433],[2.735,2.42],[2.679,2.452],[2.679,2.502],[2.66,2.52],[2.598,2.545],[2.436,2.545],[2.417,2.527],[2.417,2.464],[2.386,2.433],[2.348,2.433],[2.336,2.421],[2.292,2.452],[2.292,2.502],[2.249,2.533],[2.211,2.546],[2.037,2.546],[2.018,2.527],[2.018,2.452],[1.974,2.421],[1.937,2.421],[1.906,2.452],[1.906,2.502],[1.887,2.521],[1.812,2.546],[1.65,2.546],[1.632,2.527],[1.619,2.452],[1.588,2.421],[1.563,2.421],[1.519,2.453],[1.519,2.502],[1.501,2.521],[1.426,2.546],[1.251,2.546],[1.233,2.528],[1.233,2.478],[1.22,2.453],[1.189,2.422],[1.151,2.422],[1.133,2.44],[1.133,2.478],[1.114,2.521],[1.077,2.521],[1.027,2.546],[0.865,2.547],[0.834,2.503],[0.834,2.453],[0.802,2.422],[0.765,2.422],[0.746,2.441],[0.746,2.491],[0.728,2.522],[0.628,2.534],[0.615,2.547],[0.478,2.547],[0.447,2.528],[0.435,2.441],[0.416,2.422],[0.378,2.422],[0.36,2.441],[0.36,2.491],[0.329,2.522],[0.241,2.535],[0.229,2.547],[0.079,2.547],[0.048,2.504],[0.048,2.441],[0.029,2.423],[0.004,2.423],[-0.027,2.441],[-0.027,2.491],[-0.058,2.522],[-0.095,2.522],[-0.158,2.547],[-0.32,2.548],[-0.338,2.529],[-0.351,2.442],[-0.382,2.423],[-0.413,2.442],[-0.413,2.491],[-0.438,2.516],[-0.494,2.535],[-0.557,2.535],[-0.569,2.548],[-0.681,2.548],[-0.719,2.535],[-0.737,2.504],[-0.737,2.442],[-0.756,2.423],[-0.781,2.423],[-0.8,2.442],[-0.8,2.504],[-0.831,2.523],[-0.943,2.536],[-0.956,2.548],[-1.093,2.548],[-1.124,2.529],[-1.136,2.442],[-1.155,2.423],[-1.186,2.442],[-1.186,2.492],[-1.217,2.523],[-1.28,2.523],[-1.292,2.536],[-1.666,2.536],[-1.691,2.524],[-1.722,2.492],[-1.722,2.393],[-1.71,2.38],[-1.71,2.281],[-1.698,2.268],[-1.71,2.256],[-1.71,2.143]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{}}},"bounds":{"min":[6.51,-0.093,-0.72],"max":[17.12,2.54,0.72]},"volume_in3":7.002,"centroid":[12.5963,1.1112,0],"shell":[12.1549,0.9498,0],"area_in2":95.5744,"triangles":5072,"manifold":true,"slabs":[[6.51,0.935,-0.72,6.903,1.6,0.72],[6.903,0.269,-0.72,7.296,1.6,0.72],[7.296,0.098,-0.72,13.976,1.6,0.72],[13.976,0.098,-0.72,14.369,1.382,0.72],[14.369,0.038,-0.72,14.762,1.364,0.72],[14.762,-0.093,-0.72,16.334,2.54,0.72],[16.334,-0.093,-0.72,16.727,2.422,0.72],[16.727,0.044,-0.72,17.12,1.769,0.72]],"slots":["receiver"]},"panzer-ar57-ult-16-upper.receiver":{"part":"panzer-ar57-ult-16-upper","component":"receiver","model":"panzer-ar57-ult-16-upper.receiver.glb","script":"panzer_ar57_ult_upper.py","inputs":{"fn-p90-50-magazine.height":0.77,"fn-p90-50-magazine.width":1.949,"panzer-ar57-ult-16-upper.barrel_od":0.53,"panzer-ar57-ult-16-upper.barrel_rear_x":5.508,"panzer-ar57-ult-16-upper.bolt_end_d":0.75,"panzer-ar57-ult-16-upper.bolt_end_proud":0.05,"panzer-ar57-ult-16-upper.bolt_window_depth":0.3,"panzer-ar57-ult-16-upper.bolt_window_front_x":3.8,"panzer-ar57-ult-16-upper.bolt_window_rear_x":3.03,"panzer-ar57-ult-16-upper.bore_axis_above_pin":0.957,"panzer-ar57-ult-16-upper.catch_bottom_y":1.77,"panzer-ar57-ult-16-upper.catch_front_x":3.16,"panzer-ar57-ult-16-upper.catch_out":0.3,"panzer-ar57-ult-16-upper.catch_rear_x":2.93,"panzer-ar57-ult-16-upper.catch_top_y":2.14,"panzer-ar57-ult-16-upper.channel_bottom_y":0.46,"panzer-ar57-ult-16-upper.channel_depth":0.1,"panzer-ar57-ult-16-upper.channel_front_x":6.83,"panzer-ar57-ult-16-upper.channel_gap":0.03,"panzer-ar57-ult-16-upper.channel_rear_x":0.57,"panzer-ar57-ult-16-upper.channel_top_y":1,"panzer-ar57-ult-16-upper.cross_hole_d":0.125,"panzer-ar57-ult-16-upper.cross_hole_depth":0.1,"panzer-ar57-ult-16-upper.cross_hole_y":2.26,"panzer-ar57-ult-16-upper.feed_notch_length":1.52,"panzer-ar57-ult-16-upper.feed_pocket_d":1.883,"panzer-ar57-ult-16-upper.feed_pocket_floor_y":1.055,"panzer-ar57-ult-16-upper.feed_pocket_x":5.045,"panzer-ar57-ult-16-upper.front_block_face_x":14.939,"panzer-ar57-ult-16-upper.front_block_rear_x":15,"panzer-ar57-ult-16-upper.front_hole_pitch":0.269,"panzer-ar57-ult-16-upper.front_hole_x":15.19,"panzer-ar57-ult-16-upper.front_hole_y":2.22,"panzer-ar57-ult-16-upper.front_rail_front_x":16.32,"panzer-ar57-ult-16-upper.front_rail_slot0_x":15.282,"panzer-ar57-ult-16-upper.front_rail_slots":3,"panzer-ar57-ult-16-upper.front_rail_top_above_pin":2.54,"panzer-ar57-ult-16-upper.handguard_bottom_y":0.098,"panzer-ar57-ult-16-upper.handguard_front_x":17.12,"panzer-ar57-ult-16-upper.handguard_rear_bottom_x":7.26,"panzer-ar57-ult-16-upper.handguard_rear_top_x":6.51,"panzer-ar57-ult-16-upper.handguard_wall":0.12,"panzer-ar57-ult-16-upper.handguard_width":1.44,"panzer-ar57-ult-16-upper.handle_bottom_y":0.67,"panzer-ar57-ult-16-upper.handle_front_x":6.74,"panzer-ar57-ult-16-upper.handle_out":0.2,"panzer-ar57-ult-16-upper.handle_rear_x":5,"panzer-ar57-ult-16-upper.handle_top_y":0.99,"panzer-ar57-ult-16-upper.keel_top_y":0.259,"panzer-ar57-ult-16-upper.keel_width":0.67,"panzer-ar57-ult-16-upper.latch_bottom_y":1.78,"panzer-ar57-ult-16-upper.latch_top_y":2.12,"panzer-ar57-ult-16-upper.latch_width":0.62,"panzer-ar57-ult-16-upper.lower_chamfer_top_y":0.665,"panzer-ar57-ult-16-upper.lower_face_angle":133.48,"panzer-ar57-ult-16-upper.lower_hole_pitch":0.308,"panzer-ar57-ult-16-upper.lower_hole_x":15.33,"panzer-ar57-ult-16-upper.lower_hole_y":0.186,"panzer-ar57-ult-16-upper.lower_rail_bottom_y":-0.093,"panzer-ar57-ult-16-upper.lower_rail_slot0_x":15.51,"panzer-ar57-ult-16-upper.lug_clearance":0.005,"panzer-ar57-ult-16-upper.mag_rear_x":4.07,"panzer-ar57-ult-16-upper.mag_underside_y":1.6,"panzer-ar57-ult-16-upper.mlok_lower_axis_y":1.0458,"panzer-ar57-ult-16-upper.mlok_lower_face_distance":0.7845,"panzer-ar57-ult-16-upper.mlok_lower_front_x":15.5,"panzer-ar57-ult-16-upper.mlok_lower_slots":5,"panzer-ar57-ult-16-upper.mlok_lower_y":0.506,"panzer-ar57-ult-16-upper.mlok_lower_z":0.5692,"panzer-ar57-ult-16-upper.mlok_upper_front_x":16.32,"panzer-ar57-ult-16-upper.mlok_upper_slots":6,"panzer-ar57-ult-16-upper.mlok_upper_y":1.005,"panzer-ar57-ult-16-upper.muzzle_end_x":23.508,"panzer-ar57-ult-16-upper.muzzle_end_x_pinframe":23.325,"panzer-ar57-ult-16-upper.plate_notch_front_x":3.47,"panzer-ar57-ult-16-upper.plate_notch_rear_x":2.97,"panzer-ar57-ult-16-upper.plate_notch_top_y":0.777,"panzer-ar57-ult-16-upper.plate_screw_d":0.21,"panzer-ar57-ult-16-upper.plate_screw_front_x":6.43,"panzer-ar57-ult-16-upper.plate_screw_mid_x":2.78,"panzer-ar57-ult-16-upper.plate_screw_rear_x":0.94,"panzer-ar57-ult-16-upper.plate_screw_y":0.64,"panzer-ar57-ult-16-upper.rail_block_front_x":3.97,"panzer-ar57-ult-16-upper.rail_front_x":3.978,"panzer-ar57-ult-16-upper.rail_rear_x":-1.723,"panzer-ar57-ult-16-upper.rail_rear_x_pinframe":-1.723,"panzer-ar57-ult-16-upper.rail_slot0_x":-1.248,"panzer-ar57-ult-16-upper.rail_slots":13,"panzer-ar57-ult-16-upper.rail_top_above_pin":2.545,"panzer-ar57-ult-16-upper.receiver_chamfer_front_low_x":3.5,"panzer-ar57-ult-16-upper.receiver_chamfer_front_low_y":1.319,"panzer-ar57-ult-16-upper.receiver_chamfer_front_top_x":3.7,"panzer-ar57-ult-16-upper.receiver_chamfer_front_top_y":1.494,"panzer-ar57-ult-16-upper.receiver_chamfer_top_y":1.525,"panzer-ar57-ult-16-upper.receiver_rear_x":-0.621,"panzer-ar57-ult-16-upper.receiver_top_y":1.59,"panzer-ar57-ult-16-upper.riser_width":0.62,"panzer-ar57-ult-16-upper.side_face_bottom_y":0.33,"panzer-ar57-ult-16-upper.side_face_top_y":1.3,"panzer-ar57-ult-16-upper.takedown_lug_front_x":0.22,"panzer-ar57-ult-16-upper.top_flat_width":0.835,"panzer-ar57-ult-16-upper.tray_dip_rear_x":13.6,"panzer-ar57-ult-16-upper.tray_front_y":1.367,"panzer-ar57-ult-16-upper.tray_top_y":1.6,"panzer-ar57-ult-16-upper.underside_y":0.2485,"panzer-ar57-ult-16-upper.width":1.44,"panzer-ar57-ult-16-upper.window2_front_x":2.585,"panzer-ar57-ult-16-upper.window2_rear_x":2.298,"panzer-ar57-ult-16-upper.window_bottom_y":1.741,"panzer-ar57-ult-16-upper.window_front_x":3.546,"panzer-ar57-ult-16-upper.window_rear_x":2.922,"panzer-ar57-ult-16-upper.window_top_y":2.127,"std.ar15.bore_axis_y":0.8775,"std.ar15.buffer_tower_front_x":-0.628,"std.ar15.buffer_tower_od":1.392,"std.ar15.buffer_tower_top_y":1.5735,"std.ar15.buffer_trough_r":0.5625,"std.ar15.deck_y":0.2485,"std.ar15.front_lug_slot_width":0.5,"std.ar15.pin_spacing":6.375,"std.ar15.rear_lug_slot_rear_x":-0.402,"std.ar15.rear_lug_slot_width":0.5,"std.ar15.rear_wall_arc_r":0.75,"std.mlok.slot_corner_r":0.0937007874015748,"std.mlok.slot_length":1.2598425196850394,"std.mlok.slot_pitch":1.574803149606299,"std.mlok.slot_width":0.2755905511811024,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{"side":[[-1.723,2.131],[-1.71,2.118],[-1.71,2.069],[-1.642,2],[-1.567,1.962],[-1.492,1.937],[-1.442,1.937],[-1.43,1.925],[-1.38,1.925],[-1.318,1.9],[-1.218,1.887],[-1.106,1.837],[-0.975,1.706],[-0.919,1.6],[-0.894,1.588],[-0.67,1.588],[-0.651,1.569],[-0.651,1.494],[-0.676,1.432],[-0.676,1.382],[-0.688,1.37],[-0.688,1.27],[-0.689,0.771],[-0.676,0.759],[-0.677,0.659],[-0.664,0.646],[-0.652,0.547],[-0.627,0.497],[-0.583,0.453],[-0.446,0.44],[-0.228,0.284],[-0.228,-0.152],[-0.185,-0.196],[-0.147,-0.208],[-0.11,-0.208],[-0.097,-0.221],[0.164,-0.221],[0.177,-0.208],[0.252,-0.196],[0.289,-0.171],[0.295,-0.015],[0.308,-0.003],[0.308,0.222],[0.327,0.24],[0.551,0.24],[0.564,0.253],[1.013,0.24],[1.761,0.239],[1.773,0.252],[1.836,0.252],[2.085,0.251],[2.097,0.239],[2.16,0.239],[2.172,0.251],[2.21,0.239],[2.247,0.239],[2.259,0.251],[2.808,0.251],[2.82,0.238],[2.858,0.238],[2.933,0.238],[2.945,0.251],[6.137,0.248],[6.156,0.23],[6.155,-0.082],[6.193,-0.144],[6.236,-0.188],[6.311,-0.226],[6.374,-0.238],[6.386,-0.226],[6.436,-0.226],[6.648,-0.114],[6.673,-0.114],[6.698,-0.089],[6.723,-0.089],[6.76,-0.064],[6.785,-0.064],[6.885,-0.014],[6.922,-0.014],[6.997,0.023],[7.035,0.023],[7.097,0.048],[7.147,0.048],[7.159,0.06],[7.222,0.06],[7.234,0.073],[7.346,0.073],[7.359,0.085],[14.541,0.092],[15.139,-0.12],[15.301,-0.12],[15.313,-0.108],[15.351,-0.108],[15.37,-0.064],[15.37,-0.015],[15.388,0.004],[15.426,0.004],[15.444,-0.015],[15.457,-0.077],[15.5,-0.108],[15.725,-0.108],[15.744,-0.09],[15.744,-0.04],[15.775,0.016],[15.831,-0.027],[15.843,-0.09],[15.887,-0.108],[16.099,-0.109],[16.13,-0.09],[16.13,-0.04],[16.161,0.016],[16.205,-0.015],[16.217,-0.09],[16.236,-0.109],[16.548,-0.109],[16.616,-0.028],[16.666,0.084],[16.666,0.109],[16.766,0.284],[16.829,0.346],[16.866,0.408],[16.953,0.508],[17.003,0.595],[17.05,0.642],[17.05,1.225],[17.023,1.225],[17.004,1.243],[16.979,1.293],[16.917,1.356],[16.817,1.505],[16.767,1.555],[16.518,2.004],[16.381,2.179],[16.344,2.266],[16.307,2.316],[16.269,2.429],[16.219,2.503],[16.176,2.535],[16.088,2.535],[16.076,2.522],[15.976,2.51],[15.958,2.491],[15.957,2.441],[15.914,2.41],[15.883,2.454],[15.883,2.516],[15.864,2.535],[15.689,2.535],[15.59,2.498],[15.571,2.429],[15.552,2.41],[15.527,2.41],[15.509,2.429],[15.496,2.516],[15.478,2.535],[15.303,2.535],[15.291,2.523],[15.216,2.51],[15.197,2.467],[15.197,2.429],[15.166,2.411],[15.122,2.442],[15.11,2.504],[15.079,2.535],[14.954,2.536],[14.947,1.382],[14.928,1.364],[14.192,1.364],[13.98,1.364],[13.793,1.427],[13.694,1.477],[13.631,1.489],[13.588,1.52],[13.607,1.539],[13.681,1.539],[13.706,1.552],[13.713,1.558],[13.694,1.576],[4.056,1.584],[4.037,1.603],[4.038,2.114],[4.025,2.126],[4.038,2.139],[4.025,2.326],[4.038,2.338],[4.038,2.476],[3.932,2.544],[3.62,2.544],[3.602,2.526],[3.602,2.463],[3.57,2.432],[3.483,2.432],[3.452,2.451],[3.452,2.501],[3.421,2.532],[3.383,2.545],[3.221,2.545],[3.203,2.501],[3.203,2.451],[3.184,2.433],[3.159,2.433],[3.084,2.433],[3.065,2.451],[3.065,2.501],[3.034,2.532],[2.997,2.545],[2.835,2.545],[2.804,2.501],[2.804,2.452],[2.785,2.433],[2.747,2.433],[2.735,2.42],[2.679,2.452],[2.679,2.502],[2.66,2.52],[2.598,2.545],[2.436,2.545],[2.417,2.527],[2.417,2.464],[2.386,2.433],[2.348,2.433],[2.336,2.421],[2.292,2.452],[2.292,2.502],[2.249,2.533],[2.211,2.546],[2.037,2.546],[2.018,2.527],[2.018,2.452],[1.974,2.421],[1.937,2.421],[1.906,2.452],[1.906,2.502],[1.887,2.521],[1.812,2.546],[1.65,2.546],[1.632,2.527],[1.619,2.452],[1.588,2.421],[1.563,2.421],[1.519,2.453],[1.519,2.502],[1.501,2.521],[1.426,2.546],[1.251,2.546],[1.233,2.528],[1.233,2.478],[1.22,2.453],[1.189,2.422],[1.151,2.422],[1.133,2.44],[1.133,2.478],[1.114,2.521],[1.077,2.521],[1.027,2.546],[0.865,2.547],[0.834,2.503],[0.834,2.453],[0.802,2.422],[0.765,2.422],[0.746,2.441],[0.746,2.491],[0.728,2.522],[0.628,2.534],[0.615,2.547],[0.478,2.547],[0.447,2.528],[0.435,2.441],[0.416,2.422],[0.378,2.422],[0.36,2.441],[0.36,2.491],[0.329,2.522],[0.241,2.535],[0.229,2.547],[0.079,2.547],[0.048,2.504],[0.048,2.441],[0.029,2.423],[0.004,2.423],[-0.027,2.441],[-0.027,2.491],[-0.058,2.522],[-0.095,2.522],[-0.158,2.547],[-0.32,2.548],[-0.338,2.529],[-0.351,2.442],[-0.382,2.423],[-0.413,2.442],[-0.413,2.491],[-0.438,2.516],[-0.494,2.535],[-0.557,2.535],[-0.569,2.548],[-0.681,2.548],[-0.719,2.535],[-0.737,2.504],[-0.737,2.442],[-0.756,2.423],[-0.781,2.423],[-0.8,2.442],[-0.8,2.504],[-0.831,2.523],[-0.943,2.536],[-0.956,2.548],[-1.093,2.548],[-1.124,2.529],[-1.136,2.442],[-1.155,2.423],[-1.186,2.442],[-1.186,2.492],[-1.217,2.523],[-1.28,2.523],[-1.292,2.536],[-1.666,2.536],[-1.691,2.524],[-1.722,2.492],[-1.722,2.393],[-1.71,2.38],[-1.71,2.281],[-1.698,2.268],[-1.71,2.256],[-1.71,2.143]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{}}},"bounds":{"min":[-1.723,-0.238,-0.72],"max":[7.397,2.427,0.92]},"volume_in3":15.6771,"centroid":[2.6873,1.0537,-0.0009],"shell":[3.0252,1.0791,0.0755],"area_in2":77.5555,"triangles":5002,"manifold":true,"rear_corner":{"r":0.75,"centre":[0.122,0.9985],"x":[-0.628,-0.0116],"reach_z":0.696,"trough_r":0.5625},"slabs":[[-1.723,1.903,-0.31,-1.326,2.427,0.31],[-1.326,1.621,-0.31,-0.93,2.427,0.31],[-0.93,0.405,-0.72,-0.533,2.427,0.72],[-0.533,-0.221,-0.72,0.26,2.427,0.72],[0.26,0.248,-0.72,4.225,2.427,0.72],[4.225,0.248,-0.72,4.621,1.6,0.72],[4.621,0.248,-0.72,5.414,1.055,0.92],[5.414,0.248,-0.72,5.811,1.6,0.92],[5.811,-0.159,-0.72,6.207,1.6,0.92],[6.207,-0.238,-0.72,6.604,1.6,0.92],[6.604,-0.138,-0.72,7,1.441,0.92],[7,0.023,-0.72,7.397,0.769,0.72]],"slots":["receiver","bolt"]},"precision-armament-m4-72":{"part":"precision-armament-m4-72","model":"precision-armament-m4-72.glb","script":"precision_armament_m4_72.py","inputs":{"precision-armament-m4-72.base_af":0.766,"precision-armament-m4-72.base_flats":8,"precision-armament-m4-72.base_front_chamfer":0.05,"precision-armament-m4-72.base_front_r":0.372,"precision-armament-m4-72.base_length":0.315,"precision-armament-m4-72.base_rear_chamfer":0.025,"precision-armament-m4-72.body_rear_x":0.633,"precision-armament-m4-72.bore_d":0.29,"precision-armament-m4-72.chamber_d":0.562,"precision-armament-m4-72.edge_break":0.006,"precision-armament-m4-72.edge_round":0.02,"precision-armament-m4-72.flat_width":0.263,"precision-armament-m4-72.front_bevel_len":0.037,"precision-armament-m4-72.front_bevel_r":0.072,"precision-armament-m4-72.groove_d":0.682,"precision-armament-m4-72.length":2.25,"precision-armament-m4-72.od":0.865,"precision-armament-m4-72.overall_length":2.25,"precision-armament-m4-72.port_1_front_x":1.054,"precision-armament-m4-72.port_1_rear_x":0.774,"precision-armament-m4-72.port_2_front_x":1.482,"precision-armament-m4-72.port_2_rear_x":1.195,"precision-armament-m4-72.port_3_front_x":2.121,"precision-armament-m4-72.port_3_rear_x":1.607,"precision-armament-m4-72.port_end_r":0.04,"precision-armament-m4-72.port_front_angle":30.3,"precision-armament-m4-72.port_rear_angle":54.7,"precision-armament-m4-72.port_z_in":0.215,"precision-armament-m4-72.ports":3,"precision-armament-m4-72.ring_front_x":0.543,"precision-armament-m4-72.ring_rear_x":0.394,"precision-armament-m4-72.thread_depth":0.69,"precision-armament-m4-72.thread_major_d":0.4957,"precision-armament-m4-72.thread_minor_d":0.4551,"precision-armament-m4-72.thread_pitch":0.03571,"precision-armament-m4-72.window_1_x0":0.926,"precision-armament-m4-72.window_1_x1":1.051,"precision-armament-m4-72.window_1_y0":-0.14,"precision-armament-m4-72.window_1_y1":0.232,"precision-armament-m4-72.window_2_x0":1.327,"precision-armament-m4-72.window_2_x1":1.482,"precision-armament-m4-72.window_2_y0":-0.147,"precision-armament-m4-72.window_2_y1":0.239,"precision-armament-m4-72.window_3_x0":1.781,"precision-armament-m4-72.window_3_x1":2.07,"precision-armament-m4-72.window_3_y0":-0.285,"precision-armament-m4-72.window_3_y1":0.277,"precision-armament-m4-72.window_r":0.06},"profiles":{},"bounds":{"min":[0,-0.4325,-0.4325],"max":[2.25,0.412,0.4325]},"volume_in3":0.6494,"centroid":[1.0888,-0.0046,0],"shell":[1.0853,-0.0012,0.0001],"area_in2":12.3258,"triangles":28716,"manifold":true,"slabs":[[0,-0.433,-0.433,2.25,0.412,0.433]],"slots":["body"]},"primary-arms-deluxe-30mm-mount":{"part":"primary-arms-deluxe-30mm-mount","model":"primary-arms-deluxe-30mm-mount.glb","script":"primary_arms_deluxe_30mm_mount.py","inputs":{"primary-arms-deluxe-30mm-mount.arm_width":1.2,"primary-arms-deluxe-30mm-mount.base_behind_rear_bolt":0.395,"primary-arms-deluxe-30mm-mount.base_foot_front_x":2.45,"primary-arms-deluxe-30mm-mount.base_left_break":0.07,"primary-arms-deluxe-30mm-mount.base_rear_chamfer":0.13,"primary-arms-deluxe-30mm-mount.base_rear_chamfer_drop":0.17,"primary-arms-deluxe-30mm-mount.base_right_break":0.12,"primary-arms-deluxe-30mm-mount.base_right_z":0.6,"primary-arms-deluxe-30mm-mount.base_slope_top_x":2.89,"primary-arms-deluxe-30mm-mount.base_top_above_rail":0.4,"primary-arms-deluxe-30mm-mount.clamp_bar_outer_z":0.65,"primary-arms-deluxe-30mm-mount.clamp_bar_seam_groove":0.012,"primary-arms-deluxe-30mm-mount.clamp_bar_thickness":0.23,"primary-arms-deluxe-30mm-mount.clamp_bolt_above_rail_top":0,"primary-arms-deluxe-30mm-mount.clamp_bolt_bar_width":0.19,"primary-arms-deluxe-30mm-mount.clamp_bolt_head_d":0.31,"primary-arms-deluxe-30mm-mount.clamp_bolt_head_h":0.03,"primary-arms-deluxe-30mm-mount.clamp_bolt_spacing":1.97,"primary-arms-deluxe-30mm-mount.clamp_nut_af":0.51,"primary-arms-deluxe-30mm-mount.clamp_nut_collar_d":0.44,"primary-arms-deluxe-30mm-mount.clamp_nut_collar_h":0.19,"primary-arms-deluxe-30mm-mount.clamp_nut_h":0.47,"primary-arms-deluxe-30mm-mount.clamp_nut_recess_d":0.33,"primary-arms-deluxe-30mm-mount.clamp_nut_recess_depth":0.07,"primary-arms-deluxe-30mm-mount.clamp_nut_slot_depth":0.1,"primary-arms-deluxe-30mm-mount.clamp_nut_slot_width":0.08,"primary-arms-deluxe-30mm-mount.clamp_stud_d":0.145,"primary-arms-deluxe-30mm-mount.clamp_stud_end_below_nut_end":0.06,"primary-arms-deluxe-30mm-mount.optical_axis_above_rail":1.5,"primary-arms-deluxe-30mm-mount.ring_bore":1.1811023622047243,"primary-arms-deluxe-30mm-mount.ring_edge_break":0.026,"primary-arms-deluxe-30mm-mount.ring_facet_bottom_below_axis":0.76,"primary-arms-deluxe-30mm-mount.ring_flat_bottom_below_axis":0.437,"primary-arms-deluxe-30mm-mount.ring_front_x":4.65,"primary-arms-deluxe-30mm-mount.ring_ledge_height":0.165,"primary-arms-deluxe-30mm-mount.ring_length":0.693,"primary-arms-deluxe-30mm-mount.ring_rear_x":1.435,"primary-arms-deluxe-30mm-mount.ring_screw_head_d":0.24,"primary-arms-deluxe-30mm-mount.ring_screw_head_h":0.11,"primary-arms-deluxe-30mm-mount.ring_screw_spacing":0.315,"primary-arms-deluxe-30mm-mount.ring_screw_z":0.67,"primary-arms-deluxe-30mm-mount.ring_split_above_axis":0.15,"primary-arms-deluxe-30mm-mount.ring_split_groove_depth":0.012,"primary-arms-deluxe-30mm-mount.ring_split_groove_width":0.008,"primary-arms-deluxe-30mm-mount.ring_top_above_axis":0.645,"primary-arms-deluxe-30mm-mount.ring_width":1.585,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.top_width":0.835},"profiles":{"side":[[-0.395,-1.163],[-0.384,-1.624],[-0.367,-1.644],[-0.327,-1.644],[-0.322,-1.639],[-0.307,-1.692],[-0.296,-1.703],[-0.276,-1.698],[-0.294,-1.723],[-0.285,-1.744],[-0.262,-1.77],[-0.251,-1.772],[-0.251,-1.784],[-0.243,-1.792],[-0.217,-1.803],[-0.234,-1.804],[-0.2,-1.817],[-0.091,-1.844],[0.02,-1.84],[0.188,-1.665],[0.197,-1.637],[0.216,-1.622],[0.22,-1.605],[0.225,-1.619],[0.208,-1.651],[0.329,-1.651],[0.342,-1.634],[0.333,-1.593],[0.339,-1.559],[0.354,-1.532],[0.393,-1.496],[0.445,-1.477],[0.609,-1.473],[1.534,-1.485],[1.589,-1.501],[1.611,-1.513],[1.641,-1.542],[1.662,-1.591],[1.666,-1.663],[1.706,-1.669],[1.765,-1.78],[1.798,-1.827],[1.829,-1.843],[1.959,-1.852],[2.076,-1.845],[2.084,-1.84],[2.085,-1.829],[2.092,-1.839],[2.127,-1.791],[2.125,-1.786],[2.118,-1.791],[2.124,-1.775],[2.115,-1.775],[2.108,-1.76],[2.119,-1.771],[2.122,-1.761],[2.139,-1.766],[2.192,-1.682],[2.175,-1.678],[2.178,-1.671],[2.196,-1.674],[2.202,-1.668],[2.205,-1.674],[2.239,-1.677],[2.362,-1.675],[2.371,-1.66],[2.373,-1.431],[2.378,-1.426],[2.585,-1.426],[2.613,-1.41],[2.767,-1.261],[2.834,-1.205],[2.874,-1.177],[2.949,-1.146],[3.013,-1.133],[3.638,-1.134],[4.065,-1.142],[4.188,-1.135],[4.34,-1.1],[4.411,-1.072],[4.54,-1.001],[4.662,-0.897],[4.748,-0.788],[4.816,-0.72],[4.887,-0.621],[4.92,-0.552],[4.963,-0.41],[4.977,0.011],[4.977,0.091],[4.971,0.082],[4.958,0.109],[4.966,0.117],[4.977,0.097],[4.977,0.113],[4.964,0.128],[4.973,0.174],[4.973,0.227],[4.894,0.616],[4.879,0.663],[4.869,0.666],[4.869,0.684],[4.865,0.673],[4.859,0.686],[4.852,0.68],[4.843,0.686],[4.821,0.682],[4.815,0.689],[4.809,0.682],[4.787,0.682],[4.778,0.688],[4.753,0.685],[4.75,0.691],[4.741,0.682],[4.716,0.682],[4.623,0.691],[4.466,0.684],[4.438,0.69],[4.429,0.684],[4.404,0.69],[4.382,0.684],[4.32,0.69],[4.32,0.311],[4.333,0.243],[4.334,0.039],[4.328,-0.057],[4.331,-0.156],[4.325,-0.165],[4.323,-0.279],[4.323,-0.487],[4.305,-0.49],[4.275,-0.623],[4.235,-0.697],[4.187,-0.752],[4.104,-0.811],[4.014,-0.851],[3.946,-0.864],[3.421,-0.86],[3.39,-0.86],[3.383,-0.866],[3.377,-0.86],[2.385,-0.851],[2.261,-0.855],[2.113,-0.852],[2.02,-0.843],[1.933,-0.81],[1.84,-0.742],[1.789,-0.679],[1.761,-0.602],[1.754,-0.404],[1.752,-0.033],[1.758,0.14],[1.745,0.168],[1.76,0.496],[1.759,0.688],[1.765,0.691],[1.765,0.709],[1.692,0.711],[1.683,0.717],[1.34,0.709],[1.334,0.715],[1.296,0.712],[1.293,0.718],[1.287,0.712],[1.266,0.712],[1.262,0.718],[1.247,0.712],[1.198,0.715],[1.167,0.706],[1.164,0.715],[1.153,0.664],[1.117,0.296],[1.117,0.259],[1.124,0.259],[1.124,0.252],[1.114,0.246],[1.115,0.181],[1.124,0.163],[1.112,0.141],[1.114,-0.394],[1.143,-0.706],[1.143,-0.777],[1.116,-0.882],[1.045,-0.988],[0.991,-1.036],[0.929,-1.07],[0.926,-1.076],[0.94,-1.075],[0.932,-1.083],[0.867,-1.086],[0.874,-1.095],[0.852,-1.095],[0.837,-1.083],[0.818,-1.086],[0.809,-1.095],[0.79,-1.095],[0.787,-1.086],[0.778,-1.086],[0.775,-1.092],[0.744,-1.093],[0.741,-1.086],[0.765,-1.086],[0.756,-1.08],[0.731,-1.08],[0.725,-1.086],[0.719,-1.08],[0.694,-1.077],[0.679,-1.09],[0.676,-1.084],[0.673,-1.09],[0.66,-1.084],[0.651,-1.09],[0.636,-1.077],[0.625,-1.082],[0.626,-1.09],[0.614,-1.09],[0.608,-1.081],[0.574,-1.087],[0.537,-1.081],[0.544,-1.089],[0.53,-1.096],[0.527,-1.087],[0.504,-1.086],[0.527,-1.084],[0.527,-1.078],[0.456,-1.078],[0.438,-1.081],[0.439,-1.089],[0.431,-1.091],[0.428,-1.078],[0.407,-1.078],[0.401,-1.085],[0.379,-1.078],[0.365,-1.083],[0.376,-1.091],[0.359,-1.092],[0.357,-1.119],[0.354,-1.1],[0.328,-1.105],[0.331,-1.093],[0.32,-1.079],[0.317,-1.091],[0.303,-1.09],[0.309,-1.099],[0.306,-1.114],[0.314,-1.119],[0.258,-1.116],[0.257,-1.124],[0.248,-1.127],[0.257,-1.136],[0.246,-1.141],[0.271,-1.141],[0.282,-1.145],[0.28,-1.15],[0.03,-1.148],[0.053,-1.143],[0.042,-1.142],[0.03,-1.126],[0.019,-1.134],[0.033,-1.142],[-0.001,-1.148],[-0.375,-1.143],[-0.388,-1.149]]},"features":{"side":{"bar":[[[2.349,-1.187],[-0.391,-1.182],[-0.389,-1.658],[0.341,-1.655],[0.34,-1.479],[1.63,-1.48],[1.63,-1.672],[2.351,-1.669]]],"nuts":[[[2.21,-1.333],[1.66,-1.335],[1.662,-1.842],[2.212,-1.84]],[[0.185,-1.31],[-0.387,-1.312],[-0.385,-1.856],[0.187,-1.854]]],"split":[[[4.972,0.159],[4.329,0.156],[4.329,0.138],[4.972,0.14]],[[1.756,0.159],[1.113,0.156],[1.113,0.141],[1.756,0.144]]]}},"placement":{"side":{"plane":"xy","offset":{"y":"optical_axis_above_rail"}}},"bounds":{"min":[-0.395,-0.2944,-1.12],"max":[4.9965,2.145,0.7925]},"axis_y":1.5,"volume_in3":4.4809,"centroid":[2.1651,0.5547,-0.0353],"shell":[2.2703,0.7452,-0.0599],"area_in2":38.4347,"triangles":16656,"manifold":true,"rail_seat":{"x":[-0.395,2.45],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-0.395,-0.294,-1.12,0.375,0.4,0.63],[0.375,-0.196,-0.65,0.76,0.4,0.6],[0.76,-0.196,-0.793,1.531,2.145,0.793],[1.531,-0.263,-1.12,1.916,2.145,0.793],[1.916,-0.294,-1.12,2.301,0.749,0.63],[2.301,-0.196,-0.65,2.686,0.69,0.6],[2.686,0.093,-0.6,3.071,0.686,0.6],[3.071,0.339,-0.6,3.841,0.686,0.6],[3.841,0.334,-0.6,4.226,0.81,0.6],[4.226,0.35,-0.793,4.611,2.145,0.793],[4.611,0.536,-0.793,4.997,2.145,0.793]],"slots":["body","hardware"]},"primary-arms-slx-1-6x24-gen-iv":{"part":"primary-arms-slx-1-6x24-gen-iv","model":"primary-arms-slx-1-6x24-gen-iv.glb","script":"primary_arms_slx_1_6x24_gen_iv.py","inputs":{"primary-arms-slx-1-6x24-gen-iv.boss_behind_station":0.235,"primary-arms-slx-1-6x24-gen-iv.boss_below_axis":0.694,"primary-arms-slx-1-6x24-gen-iv.boss_d":0.3,"primary-arms-slx-1-6x24-gen-iv.cap_d":1.302,"primary-arms-slx-1-6x24-gen-iv.cap_lugs":18,"primary-arms-slx-1-6x24-gen-iv.cap_medallion_d":0.6,"primary-arms-slx-1-6x24-gen-iv.coin_slot_depth":0.04,"primary-arms-slx-1-6x24-gen-iv.diopter_pocket_depth":0.03,"primary-arms-slx-1-6x24-gen-iv.diopter_pocket_from":0.15,"primary-arms-slx-1-6x24-gen-iv.diopter_pocket_to":0.28,"primary-arms-slx-1-6x24-gen-iv.diopter_ring_lugs":18,"primary-arms-slx-1-6x24-gen-iv.elevation_top_above_axis":1.232,"primary-arms-slx-1-6x24-gen-iv.eyepiece_lens_d":1.32,"primary-arms-slx-1-6x24-gen-iv.eyepiece_rear_x":0.001,"primary-arms-slx-1-6x24-gen-iv.eyepiece_rim_id":1.63,"primary-arms-slx-1-6x24-gen-iv.illumination_knob_lugs":18,"primary-arms-slx-1-6x24-gen-iv.illumination_reach":1.387,"primary-arms-slx-1-6x24-gen-iv.illumination_slot_length":0.52,"primary-arms-slx-1-6x24-gen-iv.illumination_slot_turned":52,"primary-arms-slx-1-6x24-gen-iv.illumination_slot_width":0.06,"primary-arms-slx-1-6x24-gen-iv.knob_flute_depth":0.02,"primary-arms-slx-1-6x24-gen-iv.length":10.4,"primary-arms-slx-1-6x24-gen-iv.lever_screw_d":0.11,"primary-arms-slx-1-6x24-gen-iv.lever_screw_front_x":2.78,"primary-arms-slx-1-6x24-gen-iv.lever_screw_pocket_depth":0.03,"primary-arms-slx-1-6x24-gen-iv.lever_screw_rear_x":2.61,"primary-arms-slx-1-6x24-gen-iv.lever_tip_above_axis":1.611,"primary-arms-slx-1-6x24-gen-iv.lever_width":0.3,"primary-arms-slx-1-6x24-gen-iv.magnification_ring_lug_places":18,"primary-arms-slx-1-6x24-gen-iv.magnification_ring_lug_width":0.166,"primary-arms-slx-1-6x24-gen-iv.magnification_ring_r":0.91,"primary-arms-slx-1-6x24-gen-iv.objective_bore_d":1.02,"primary-arms-slx-1-6x24-gen-iv.objective_front_x":10.401,"primary-arms-slx-1-6x24-gen-iv.objective_glass_recess":0.4,"primary-arms-slx-1-6x24-gen-iv.objective_lens_d":0.9448818897637795,"primary-arms-slx-1-6x24-gen-iv.ocular_glass_recess":0.25,"primary-arms-slx-1-6x24-gen-iv.plug_proud":0.05,"primary-arms-slx-1-6x24-gen-iv.saddle_flat_bottom":0.793,"primary-arms-slx-1-6x24-gen-iv.saddle_flat_top":0.739,"primary-arms-slx-1-6x24-gen-iv.saddle_radius":0.9468,"primary-arms-slx-1-6x24-gen-iv.saddle_x":6.604,"primary-arms-slx-1-6x24-gen-iv.tube_front_from":7.341,"primary-arms-slx-1-6x24-gen-iv.tube_od":1.1811023622047243,"primary-arms-slx-1-6x24-gen-iv.tube_rear_from":3.23,"primary-arms-slx-1-6x24-gen-iv.tube_rear_to":5.861,"primary-arms-slx-1-6x24-gen-iv.windage_reach":1.234},"profiles":{"body":[[-0.194,0.013],[-0.194,-0.014],[-0.189,-0.02],[-0.189,-0.188],[-0.183,-0.193],[-0.178,-0.334],[-0.172,-0.34],[-0.167,-0.427],[-0.162,-0.432],[-0.162,-0.465],[-0.156,-0.47],[-0.156,-0.503],[-0.151,-0.508],[-0.14,-0.59],[-0.101,-0.72],[-0.074,-0.774],[-0.049,-0.804],[-0.016,-0.821],[0.033,-0.826],[0.049,-0.837],[0.115,-0.848],[0.121,-0.854],[0.23,-0.854],[0.241,-0.849],[0.247,-0.854],[0.29,-0.854],[0.296,-0.86],[0.34,-0.86],[0.345,-0.866],[0.405,-0.866],[0.411,-0.871],[0.471,-0.866],[0.477,-0.861],[0.488,-0.861],[0.499,-0.872],[0.548,-0.872],[0.559,-0.866],[0.57,-0.872],[0.575,-0.861],[0.581,-0.872],[0.828,-0.873],[0.833,-0.868],[1.64,-0.871],[1.645,-0.865],[1.788,-0.866],[1.794,-0.872],[1.81,-0.866],[1.821,-0.872],[1.827,-0.866],[1.975,-0.867],[1.981,-0.872],[2.025,-0.872],[2.03,-0.856],[2.036,-0.862],[2.096,-0.862],[2.102,-0.867],[2.168,-0.868],[2.173,-0.851],[2.212,-0.895],[2.228,-0.895],[2.234,-0.906],[2.47,-0.907],[2.542,-0.88],[2.558,-0.886],[2.564,-0.875],[2.597,-0.875],[2.624,-0.864],[2.657,-0.859],[2.668,-0.864],[2.674,-0.859],[2.707,-0.875],[2.8,-0.897],[2.822,-0.908],[3.054,-0.909],[3.095,-0.836],[3.095,-0.803],[3.111,-0.803],[3.111,-0.711],[3.147,-0.714],[3.158,-0.708],[3.177,-0.689],[3.216,-0.619],[3.241,-0.594],[3.279,-0.584],[3.384,-0.584],[3.39,-0.59],[3.412,-0.59],[3.417,-0.584],[3.423,-0.59],[4.09,-0.592],[4.095,-0.587],[5.726,-0.593],[5.731,-0.588],[5.831,-0.588],[5.858,-0.599],[5.925,-0.67],[5.936,-0.665],[5.955,-0.684],[5.955,-0.7],[5.997,-0.736],[6.036,-0.753],[6.13,-0.764],[6.135,-0.769],[6.179,-0.77],[6.185,-0.775],[6.335,-0.781],[6.34,-0.787],[6.662,-0.793],[6.667,-0.788],[6.845,-0.789],[6.85,-0.783],[7.011,-0.778],[7.016,-0.773],[7.061,-0.773],[7.066,-0.768],[7.161,-0.757],[7.205,-0.741],[7.269,-0.684],[7.344,-0.599],[7.372,-0.589],[8.194,-0.592],[8.199,-0.586],[8.333,-0.587],[8.338,-0.592],[8.677,-0.594],[8.683,-0.588],[8.722,-0.588],[8.733,-0.594],[8.739,-0.588],[10.405,-0.589],[10.424,-0.576],[10.458,-0.505],[10.469,-0.444],[10.475,-0.439],[10.48,-0.379],[10.486,-0.373],[10.486,-0.34],[10.491,-0.335],[10.497,-0.225],[10.503,-0.22],[10.503,-0.138],[10.508,-0.132],[10.508,0.131],[10.503,0.136],[10.497,0.284],[10.491,0.29],[10.491,0.333],[10.486,0.339],[10.475,0.438],[10.441,0.547],[10.424,0.575],[10.405,0.588],[9.808,0.59],[9.802,0.585],[9.719,0.585],[9.713,0.59],[7.355,0.591],[7.205,0.739],[7.161,0.756],[7.066,0.767],[7.061,0.772],[7.016,0.773],[7.011,0.778],[6.944,0.778],[6.939,0.784],[6.551,0.796],[6.529,0.785],[6.34,0.785],[6.335,0.78],[6.185,0.775],[6.179,0.769],[6.135,0.769],[6.13,0.764],[6.036,0.753],[5.997,0.737],[5.955,0.702],[5.955,0.685],[5.936,0.666],[5.925,0.672],[5.858,0.601],[5.831,0.59],[3.423,0.591],[3.417,0.586],[3.412,0.592],[3.39,0.592],[3.384,0.586],[3.257,0.586],[3.241,0.592],[3.216,0.617],[3.177,0.687],[3.158,0.706],[3.147,0.712],[3.111,0.709],[3.111,0.802],[3.095,0.802],[3.095,0.835],[3.054,0.908],[2.822,0.909],[2.8,0.898],[2.707,0.876],[2.674,0.86],[2.668,0.866],[2.657,0.86],[2.624,0.866],[2.597,0.877],[2.564,0.877],[2.558,0.888],[2.542,0.882],[2.465,0.91],[2.459,0.904],[2.234,0.905],[2.228,0.894],[2.212,0.894],[2.173,0.851],[2.168,0.867],[2.102,0.867],[2.096,0.862],[2.036,0.862],[2.03,0.856],[2.025,0.873],[1.981,0.873],[1.975,0.867],[1.827,0.868],[1.821,0.873],[1.81,0.868],[1.794,0.873],[1.788,0.868],[0.581,0.871],[0.575,0.86],[0.57,0.871],[0.559,0.866],[0.548,0.871],[0.499,0.871],[0.488,0.86],[0.411,0.871],[0.405,0.866],[0.345,0.866],[0.34,0.861],[0.296,0.861],[0.29,0.855],[0.247,0.855],[0.241,0.85],[0.23,0.855],[0.121,0.856],[0.115,0.85],[0.049,0.84],[0,0.818],[-0.016,0.818],[-0.049,0.802],[-0.074,0.772],[-0.101,0.718],[-0.14,0.588],[-0.151,0.507],[-0.156,0.501],[-0.156,0.469],[-0.162,0.463],[-0.162,0.431],[-0.167,0.425],[-0.172,0.338],[-0.178,0.333],[-0.183,0.192],[-0.189,0.187],[-0.189,0.018]],"turret":[[5.944,1.176],[5.944,1.111],[5.977,1.067],[5.977,1.045],[5.955,1.013],[5.944,1.007],[5.944,0.958],[5.977,0.92],[5.977,0.794],[5.983,0.789],[5.986,0.743],[6.036,0.764],[6.13,0.775],[6.135,0.78],[6.179,0.78],[6.185,0.786],[6.335,0.791],[6.34,0.796],[6.529,0.796],[6.551,0.807],[6.662,0.806],[6.667,0.801],[6.845,0.8],[6.85,0.795],[6.939,0.795],[6.944,0.789],[7.061,0.783],[7.066,0.778],[7.161,0.767],[7.222,0.739],[7.23,0.747],[7.23,0.922],[7.263,0.955],[7.258,0.966],[7.263,0.971],[7.263,0.999],[7.23,1.048],[7.23,1.07],[7.258,1.102],[7.258,1.168],[7.188,1.215],[7.161,1.22],[7.094,1.204],[7.1,1.22],[7.039,1.22],[7.033,1.226],[7.028,1.22],[7.022,1.226],[6.817,1.226],[6.811,1.232],[6.495,1.232],[6.49,1.227],[6.191,1.228],[6.185,1.222],[6.113,1.222],[6.119,1.211],[6.157,1.211],[6.163,1.217],[6.407,1.222],[6.407,1.216],[6.324,1.216],[6.304,1.208],[6.335,1.206],[6.335,1.2],[6.096,1.206],[6.052,1.217],[6.013,1.217],[6.002,1.212]],"lever":[[2.28,1.592],[2.28,0.989],[2.349,0.915],[2.459,0.915],[2.47,0.92],[2.542,0.893],[2.558,0.898],[2.569,0.888],[2.597,0.888],[2.652,0.871],[2.668,0.876],[2.674,0.871],[2.707,0.887],[2.8,0.909],[2.822,0.92],[3.043,0.919],[3.029,0.949],[3.054,0.941],[3.062,0.949],[3.062,0.96],[3.056,0.965],[3.056,0.992],[3.004,1.039],[2.996,1.036],[3.007,1.025],[3.004,1.017],[2.946,1.069],[2.949,1.082],[2.828,1.105],[2.822,1.11],[2.795,1.11],[2.767,1.121],[2.74,1.121],[2.734,1.127],[2.657,1.138],[2.652,1.143],[2.63,1.143],[2.624,1.149],[2.597,1.149],[2.536,1.17],[2.506,1.2],[2.489,1.244],[2.495,1.581],[2.489,1.603],[2.47,1.611],[2.322,1.611],[2.316,1.606],[2.305,1.611],[2.289,1.606]],"plan":[[-0.129,0.132],[-0.129,-0.126],[-0.113,-0.142],[-0.113,-0.4],[-0.098,-0.415],[-0.098,-0.552],[-0.083,-0.568],[-0.083,-0.659],[-0.068,-0.674],[-0.068,-0.735],[-0.053,-0.75],[-0.053,-0.781],[-0.038,-0.796],[-0.038,-0.811],[-0.015,-0.834],[0.03,-0.834],[0.045,-0.85],[0.091,-0.85],[0.106,-0.865],[0.227,-0.866],[0.242,-0.851],[0.257,-0.851],[0.288,-0.821],[0.325,-0.844],[0.333,-0.867],[0.409,-0.867],[0.424,-0.883],[1.546,-0.89],[1.561,-0.875],[2.122,-0.879],[2.138,-0.894],[2.153,-0.879],[2.29,-0.88],[2.305,-0.865],[2.35,-0.926],[2.578,-0.928],[2.594,-0.913],[2.639,-0.913],[2.685,-0.883],[2.73,-0.883],[2.746,-0.868],[2.791,-0.868],[2.806,-0.884],[2.822,-0.869],[2.898,-0.915],[2.928,-0.915],[2.943,-0.93],[2.959,-0.915],[3.172,-0.917],[3.194,-0.894],[3.225,-0.818],[3.24,-0.803],[3.24,-0.788],[3.225,-0.772],[3.225,-0.726],[3.24,-0.711],[3.24,-0.681],[3.286,-0.635],[3.286,-0.62],[3.309,-0.582],[3.324,-0.597],[3.507,-0.599],[3.522,-0.583],[3.537,-0.599],[3.842,-0.601],[3.857,-0.586],[5.2,-0.594],[5.215,-0.579],[5.23,-0.595],[5.246,-0.579],[5.261,-0.595],[5.521,-0.597],[5.536,-0.581],[5.903,-0.584],[6.064,-0.745],[6.033,-0.791],[6.048,-0.806],[6.033,-0.822],[6.033,-0.867],[6.048,-0.883],[6.018,-0.913],[6.018,-0.959],[6.033,-0.974],[6.018,-0.99],[6.018,-1.005],[6.048,-1.036],[6.048,-1.066],[6.018,-1.097],[6.018,-1.173],[6.064,-1.219],[6.056,-1.242],[6.025,-1.242],[6.018,-1.25],[6.018,-1.341],[6.025,-1.349],[6.087,-1.35],[6.102,-1.365],[6.27,-1.366],[6.285,-1.382],[6.975,-1.387],[6.99,-1.371],[7.159,-1.373],[7.174,-1.357],[7.251,-1.358],[7.274,-1.335],[7.274,-1.259],[7.251,-1.235],[7.235,-1.251],[7.228,-1.243],[7.228,-1.212],[7.251,-1.205],[7.274,-1.182],[7.274,-1.105],[7.243,-1.075],[7.243,-1.044],[7.274,-1.014],[7.274,-0.906],[7.243,-0.891],[7.243,-0.723],[7.281,-0.7],[7.297,-0.7],[7.304,-0.677],[7.389,-0.593],[7.818,-0.596],[7.834,-0.581],[7.911,-0.581],[7.926,-0.597],[7.941,-0.582],[10.434,-0.598],[10.458,-0.575],[10.458,-0.56],[10.473,-0.544],[10.473,-0.514],[10.488,-0.498],[10.488,-0.452],[10.504,-0.437],[10.504,-0.345],[10.519,-0.33],[10.519,-0.161],[10.55,-0.146],[10.55,0.069],[10.519,0.085],[10.519,0.3],[10.504,0.315],[10.504,0.392],[10.488,0.407],[10.488,0.469],[10.473,0.484],[10.473,0.515],[10.458,0.53],[10.458,0.546],[10.419,0.584],[8.079,0.597],[8.064,0.582],[8.049,0.597],[7.957,0.598],[7.941,0.583],[7.926,0.598],[7.864,0.598],[7.849,0.583],[7.834,0.583],[7.818,0.598],[7.803,0.583],[7.788,0.583],[7.772,0.599],[7.757,0.599],[7.742,0.584],[7.711,0.584],[7.696,0.599],[7.496,0.6],[7.481,0.585],[7.419,0.585],[7.404,0.601],[7.389,0.585],[7.266,0.709],[7.243,0.716],[7.243,0.9],[7.258,0.915],[7.243,0.931],[7.266,0.938],[7.289,0.961],[7.289,1.007],[7.243,1.053],[7.243,1.068],[7.289,1.114],[7.289,1.175],[7.266,1.183],[7.235,1.214],[7.174,1.214],[7.159,1.23],[7.113,1.23],[7.097,1.215],[7.051,1.215],[7.036,1.23],[7.021,1.23],[7.005,1.215],[6.944,1.215],[6.929,1.231],[6.485,1.233],[6.469,1.218],[6.454,1.218],[6.439,1.233],[6.301,1.234],[6.285,1.219],[6.071,1.22],[6.025,1.189],[5.995,1.189],[5.987,1.182],[5.987,1.105],[6.018,1.075],[6.018,1.044],[5.987,0.998],[5.987,0.952],[6.018,0.937],[6.018,0.769],[6.033,0.753],[6.033,0.723],[6.048,0.707],[6.025,0.685],[5.979,0.685],[5.903,0.594],[5.184,0.597],[5.169,0.582],[5.154,0.598],[4.94,0.599],[4.925,0.584],[3.309,0.592],[3.255,0.646],[3.255,0.661],[3.225,0.707],[3.225,0.768],[3.24,0.783],[3.225,0.799],[3.21,0.845],[3.156,0.913],[2.913,0.915],[2.898,0.9],[2.852,0.9],[2.822,0.869],[2.776,0.87],[2.761,0.854],[2.746,0.855],[2.73,0.87],[2.67,0.87],[2.639,0.901],[2.609,0.901],[2.594,0.916],[2.335,0.918],[2.312,0.895],[2.305,0.857],[2.29,0.872],[1.257,0.878],[1.242,0.862],[1.227,0.878],[1.106,0.878],[1.091,0.863],[0.575,0.866],[0.56,0.881],[0.545,0.866],[0.378,0.867],[0.363,0.852],[0.333,0.852],[0.303,0.822],[0.272,0.822],[0.265,0.845],[0.242,0.868],[0.227,0.852],[0.121,0.853],[0.106,0.838],[0.03,0.838],[0.015,0.823],[-0.015,0.823],[-0.053,0.785],[-0.053,0.755],[-0.068,0.74],[-0.068,0.694],[-0.083,0.679],[-0.083,0.588],[-0.098,0.573],[-0.098,0.451],[-0.113,0.436],[-0.113,0.147]]},"features":{"body":{},"turret":{},"lever":{},"plan":{}},"placement":{"body":{"plane":"xy","offset":{}},"turret":{"plane":"xy","offset":{}},"lever":{"plane":"xy","offset":{}},"plan":{"plane":"xz","offset":{}}},"bounds":{"min":[0.001,-0.9099,-1.387],"max":[10.401,1.611,1.237]},"volume_in3":17.855,"centroid":[4.6522,0.0358,-0.0095],"shell":[4.8612,0.0687,-0.0084],"area_in2":68.8281,"triangles":36294,"manifold":true,"slabs":[[0.001,-0.873,-0.873,1.927,0.873,0.873],[1.927,-0.91,-0.906,2.697,1.611,0.906],[2.697,-0.909,-0.905,3.082,1.132,0.905],[3.082,-0.857,-0.857,3.468,0.857,0.857],[3.468,-0.587,-0.587,5.779,0.587,0.587],[5.779,-0.83,-1.387,7.32,1.235,1.237],[7.32,-0.62,-0.62,10.401,0.62,0.62]],"slots":["body","lens","medallion","hardware"]},"primary-arms-slx-cantilever-30mm-mount":{"part":"primary-arms-slx-cantilever-30mm-mount","model":"primary-arms-slx-cantilever-30mm-mount.glb","script":"primary_arms_slx_cantilever_30mm_mount.py","inputs":{"primary-arms-slx-cantilever-30mm-mount.arm_pocket_depth":0.19,"primary-arms-slx-cantilever-30mm-mount.arm_width":0.75,"primary-arms-slx-cantilever-30mm-mount.base_boss_chamfer":0.07,"primary-arms-slx-cantilever-30mm-mount.base_bottom_y":0.249,"primary-arms-slx-cantilever-30mm-mount.base_left_z":0.68,"primary-arms-slx-cantilever-30mm-mount.base_top_y":0.234,"primary-arms-slx-cantilever-30mm-mount.cap_screw_d":0.2,"primary-arms-slx-cantilever-30mm-mount.cap_screw_depth":0.075,"primary-arms-slx-cantilever-30mm-mount.cap_screw_head_h":0.03,"primary-arms-slx-cantilever-30mm-mount.clamp_bar_facet_bottom_h":0.117,"primary-arms-slx-cantilever-30mm-mount.clamp_bar_facet_depth":0.08,"primary-arms-slx-cantilever-30mm-mount.clamp_bar_facet_top_h":0.177,"primary-arms-slx-cantilever-30mm-mount.clamp_bar_length":3.2,"primary-arms-slx-cantilever-30mm-mount.clamp_bar_outer_z":0.68,"primary-arms-slx-cantilever-30mm-mount.clamp_bar_pad_half":0.21,"primary-arms-slx-cantilever-30mm-mount.clamp_bar_pad_top_half":0.09,"primary-arms-slx-cantilever-30mm-mount.clamp_bar_rear_x":0.41,"primary-arms-slx-cantilever-30mm-mount.clamp_bar_thickness":0.25,"primary-arms-slx-cantilever-30mm-mount.clamp_bolt_below_rail_top":0.007,"primary-arms-slx-cantilever-30mm-mount.clamp_bolt_counterbore_d":0.385,"primary-arms-slx-cantilever-30mm-mount.clamp_bolt_end_below_face":0.02,"primary-arms-slx-cantilever-30mm-mount.clamp_bolt_end_d":0.16,"primary-arms-slx-cantilever-30mm-mount.clamp_bolt_head_d":0.31,"primary-arms-slx-cantilever-30mm-mount.clamp_bolt_head_h":0.1,"primary-arms-slx-cantilever-30mm-mount.clamp_bolt_recess_d":0.235,"primary-arms-slx-cantilever-30mm-mount.clamp_bolt_recess_depth":0.05,"primary-arms-slx-cantilever-30mm-mount.clamp_bolt_socket_d":0.177,"primary-arms-slx-cantilever-30mm-mount.clamp_bolt_socket_depth":0.06,"primary-arms-slx-cantilever-30mm-mount.clamp_bolt_socket_waist_d":0.125,"primary-arms-slx-cantilever-30mm-mount.clamp_bolt_spacing":1.182,"primary-arms-slx-cantilever-30mm-mount.edge_break":0.006,"primary-arms-slx-cantilever-30mm-mount.lower_pocket_depth":0.06,"primary-arms-slx-cantilever-30mm-mount.optical_axis_above_rail":1.5,"primary-arms-slx-cantilever-30mm-mount.ring_bore":1.1811023622047243,"primary-arms-slx-cantilever-30mm-mount.ring_corner_chamfer":0.074,"primary-arms-slx-cantilever-30mm-mount.ring_front_x":4.197,"primary-arms-slx-cantilever-30mm-mount.ring_length":0.765,"primary-arms-slx-cantilever-30mm-mount.ring_rear_x":0.598,"primary-arms-slx-cantilever-30mm-mount.ring_screw_hole_above_axis":0.333,"primary-arms-slx-cantilever-30mm-mount.ring_screw_hole_d":0.23,"primary-arms-slx-cantilever-30mm-mount.ring_screw_spacing":0.453,"primary-arms-slx-cantilever-30mm-mount.ring_side_flat_above_axis":0.24,"primary-arms-slx-cantilever-30mm-mount.ring_side_flat_below_axis":0.25,"primary-arms-slx-cantilever-30mm-mount.ring_split_depth":0.012,"primary-arms-slx-cantilever-30mm-mount.ring_split_width":0.012,"primary-arms-slx-cantilever-30mm-mount.ring_top_above_axis":0.669,"primary-arms-slx-cantilever-30mm-mount.ring_top_flat_width":0.672,"primary-arms-slx-cantilever-30mm-mount.ring_width":1.53,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{"side":[[-0.55,-1.372],[-0.548,-1.499],[-0.349,-1.724],[-0.327,-1.743],[-0.306,-1.751],[0.221,-1.751],[0.239,-1.746],[0.286,-1.704],[0.901,-1.704],[0.945,-1.743],[0.965,-1.751],[1.433,-1.751],[1.456,-1.743],[1.498,-1.702],[2.115,-1.704],[2.152,-1.738],[2.175,-1.751],[2.715,-1.751],[2.919,-1.547],[2.981,-1.5],[3.028,-1.477],[3.428,-1.384],[4.064,-1.247],[4.175,-1.216],[4.22,-1.165],[4.38,-0.933],[4.553,-0.698],[4.561,-0.667],[4.582,-0.279],[4.579,-0.028],[4.553,-0.003],[4.579,0.026],[4.582,0.248],[4.574,0.344],[4.564,0.359],[4.561,0.38],[4.548,0.53],[4.535,0.584],[4.454,0.668],[4.433,0.673],[3.873,0.671],[3.791,0.587],[3.802,0.509],[3.796,0.506],[3.796,0.53],[3.79,0.541],[3.781,0.525],[3.765,0.129],[3.765,-0.021],[3.778,-0.034],[3.781,-0.052],[3.763,-0.072],[3.768,-0.444],[3.776,-0.576],[3.783,-0.618],[3.783,-0.721],[3.768,-0.773],[3.75,-0.798],[3.718,-0.826],[3.674,-0.844],[3.547,-0.862],[1.971,-1.056],[1.728,-1.079],[1.009,-1.076],[0.96,-1.063],[0.907,-1.018],[0.894,-0.997],[0.881,-0.954],[0.884,-0.897],[0.902,-0.855],[1,-0.713],[1.008,-0.682],[1.013,-0.69],[1.013,-0.656],[1.026,-0.643],[1.026,-0.628],[1.02,-0.637],[1.016,-0.631],[1.029,-0.618],[1.031,-0.584],[1.026,-0.576],[1.031,-0.574],[1.025,-0.572],[1.022,-0.593],[1.018,-0.571],[1.029,-0.463],[1.034,-0.121],[1.039,-0.124],[1.034,-0.111],[1.039,-0.088],[1.016,-0.049],[1.042,-0.013],[1.037,0.274],[1.024,0.509],[1.013,0.553],[1.003,0.522],[0.998,0.473],[0.985,0.026],[0.965,0.001],[0.956,0],[0.977,0.028],[0.977,0.3],[0.99,0.372],[0.998,0.509],[1.003,0.558],[1.013,0.574],[1.011,0.587],[0.927,0.671],[0.356,0.671],[0.264,0.574],[0.248,0.491],[0.238,0.364],[0.225,0.344],[0.217,0.276],[0.217,0.026],[0.243,-0.003],[0.215,-0.026],[0.21,-0.049],[0.21,-0.344],[0.243,-0.853],[0.211,-0.901],[0.131,-0.955],[-0.417,-1.267],[-0.422,-1.275],[-0.448,-1.278],[-0.528,-1.322],[-0.545,-1.341]]},"features":{"side":{"lower_pockets":[[[4.527,-0.305],[4.32,-0.305],[4.32,-0.419],[4.328,-0.458],[4.351,-0.492],[4.384,-0.514],[4.423,-0.522],[4.463,-0.514],[4.497,-0.492],[4.519,-0.458],[4.527,-0.419]],[[4.074,-0.305],[3.867,-0.305],[3.867,-0.419],[3.875,-0.458],[3.897,-0.492],[3.931,-0.514],[3.971,-0.522],[4.01,-0.514],[4.043,-0.492],[4.066,-0.458],[4.074,-0.419]],[[0.928,-0.305],[0.721,-0.305],[0.721,-0.419],[0.729,-0.458],[0.751,-0.492],[0.785,-0.514],[0.825,-0.522],[0.864,-0.514],[0.898,-0.492],[0.92,-0.458],[0.928,-0.419]],[[0.475,-0.305],[0.268,-0.305],[0.268,-0.419],[0.276,-0.458],[0.298,-0.492],[0.332,-0.514],[0.371,-0.522],[0.411,-0.514],[0.445,-0.492],[0.467,-0.458],[0.475,-0.419]]],"arm_pocket":[[[4.126,-1.102],[4.16,-1.088],[4.187,-1.064],[4.205,-1.033],[4.213,-0.997],[4.21,-0.961],[4.196,-0.927],[4.172,-0.9],[4.14,-0.882],[4.105,-0.874],[4.069,-0.877],[3.056,-1.135],[3.022,-1.15],[2.995,-1.174],[2.976,-1.205],[2.968,-1.241],[2.972,-1.277],[2.986,-1.31],[3.01,-1.338],[3.042,-1.356],[3.077,-1.364],[3.113,-1.361]]],"neck_pocket":[[[0.683,-0.933],[0.708,-0.905],[0.724,-0.871],[0.728,-0.834],[0.72,-0.798],[0.702,-0.766],[0.674,-0.741],[0.64,-0.725],[0.603,-0.721],[0.567,-0.729],[0.535,-0.747],[0.173,-1.036],[0.148,-1.064],[0.132,-1.098],[0.128,-1.135],[0.136,-1.171],[0.154,-1.203],[0.182,-1.228],[0.216,-1.244],[0.253,-1.248],[0.289,-1.24],[0.321,-1.222]]],"arches":[[[2.144,-1.755],[1.914,-1.535],[1.671,-1.535],[1.441,-1.755]],[[0.949,-1.755],[0.719,-1.535],[0.476,-1.535],[0.246,-1.755]]]}},"placement":{"side":{"plane":"xy","offset":{"y":"optical_axis_above_rail"}}},"bounds":{"min":[-0.55,-0.251,-0.765],"max":[4.5795,2.169,0.765]},"axis_y":1.5,"volume_in3":3.4312,"centroid":[1.8446,0.5271,-0.0016],"shell":[1.952,0.7106,0.0128],"area_in2":39.192,"triangles":19362,"manifold":true,"rail_seat":{"x":[-0.327,2.715],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-0.55,-0.251,-0.68,-0.155,0.382,0.68],[-0.155,-0.251,-0.715,0.239,1.879,0.715],[0.239,-0.251,-0.765,1.028,2.169,0.765],[1.028,-0.251,-0.68,3.001,0.571,0.68],[3.001,0.01,-0.375,3.396,0.619,0.375],[3.396,0.109,-0.375,3.79,0.74,0.375],[3.79,0.194,-0.765,4.185,2.169,0.765],[4.185,0.295,-0.765,4.58,2.169,0.765]],"slots":["body","hardware"]},"psa-stealth-stripped-lower":{"part":"psa-stealth-stripped-lower","model":"psa-stealth-stripped-lower.glb","script":"psa_stealth_stripped_lower.py","inputs":{"psa-stealth-stripped-lower.bolt_catch_boss_bottom_y":-0.11,"psa-stealth-stripped-lower.bolt_catch_boss_front_x":3.6,"psa-stealth-stripped-lower.bolt_catch_boss_rear_x":3.04,"psa-stealth-stripped-lower.bolt_catch_gap_front_x":3.375,"psa-stealth-stripped-lower.bolt_catch_gap_rear_x":3.203,"psa-stealth-stripped-lower.buffer_axis_above_pin":0.8775,"psa-stealth-stripped-lower.fence_bottom_y":-0.91,"psa-stealth-stripped-lower.fence_corner_r":0.1,"psa-stealth-stripped-lower.fence_front_x":3.565,"psa-stealth-stripped-lower.fence_rear_x":3.02,"psa-stealth-stripped-lower.fence_top_y":-0.22,"psa-stealth-stripped-lower.grip_mating_y":-1.071,"psa-stealth-stripped-lower.grip_seat_y":-1.0695,"psa-stealth-stripped-lower.grip_shelf_top_x":-0.095,"psa-stealth-stripped-lower.hammer_pin_x":2.771,"psa-stealth-stripped-lower.hammer_pin_y":-0.375,"psa-stealth-stripped-lower.magwell_front_x":6.148,"psa-stealth-stripped-lower.magwell_wall_curve_bottom_y_left":-1.09,"psa-stealth-stripped-lower.magwell_wall_curve_top_y_left":-0.62,"psa-stealth-stripped-lower.magwell_wall_rear_x":3.619,"psa-stealth-stripped-lower.magwell_wall_rear_x_left":3.49,"psa-stealth-stripped-lower.magwell_wall_upper_rear_x_left":2.955,"psa-stealth-stripped-lower.rear_behind_pin":1.125,"psa-stealth-stripped-lower.selector_x":0.803,"psa-stealth-stripped-lower.selector_y":-0.466,"psa-stealth-stripped-lower.tower_front_x":-0.416,"psa-stealth-stripped-lower.trigger_guard_front_x":3.3425,"psa-stealth-stripped-lower.trigger_guard_front_y":-2.18,"psa-stealth-stripped-lower.trigger_guard_rear_x":1.4985,"psa-stealth-stripped-lower.trigger_guard_rear_y":-2.18,"psa-stealth-stripped-lower.trigger_opening_top_y":-1.085,"psa-stealth-stripped-lower.trigger_pin_x":1.928,"psa-stealth-stripped-lower.trigger_pin_y":-0.689,"psa-stealth-stripped-lower.well_roll_bottom_y":-0.204,"psa-stealth-stripped-lower.well_roll_crest_out":0.8,"psa-stealth-stripped-lower.well_roll_front_x":6.231,"psa-stealth-stripped-lower.well_roll_rear_round":0.19,"psa-stealth-stripped-lower.well_roll_rear_x":2.905,"std.ar15.bolt_catch_boss_out":0.618,"std.ar15.bolt_catch_plunger_hole_d":0.156,"std.ar15.bolt_catch_plunger_hole_depth":0.4703,"std.ar15.bolt_catch_plunger_hole_y":-0.195,"std.ar15.bolt_catch_slot_bottom_y":-0.38,"std.ar15.bolt_catch_slot_floor":0.4409,"std.ar15.bolt_catch_slot_front_x":3.375,"std.ar15.bolt_catch_slot_width":0.172,"std.ar15.bore_axis_y":0.8775,"std.ar15.buffer_tower_front_x":-0.628,"std.ar15.buffer_tower_od":1.392,"std.ar15.deck_front_x":6.194,"std.ar15.deck_y":0.2485,"std.ar15.fcg_pin_hole_d":0.15675,"std.ar15.fcg_pocket_corner_r":0.218,"std.ar15.fcg_pocket_depth":1.249,"std.ar15.fcg_pocket_front_x":3.11,"std.ar15.fcg_pocket_length":2.87,"std.ar15.fcg_pocket_width":0.69,"std.ar15.front_lug_slot_width":0.5,"std.ar15.grip_lug_depth":0.93,"std.ar15.grip_lug_face_angle":60,"std.ar15.grip_lug_face_from_pin":1.228,"std.ar15.grip_lug_front_from_rear_face":2.3,"std.ar15.grip_lug_length":1.25,"std.ar15.grip_lug_width":0.375,"std.ar15.grip_seat_below_deck":1.318,"std.ar15.lower_body_width":0.88,"std.ar15.mag_catch_boss_edge_r":0.059,"std.ar15.mag_catch_boss_proud":0.0906,"std.ar15.mag_catch_boss_r":0.253,"std.ar15.mag_catch_boss_x":4.262,"std.ar15.mag_catch_cbore_d":0.312,"std.ar15.mag_catch_cbore_depth":0.25,"std.ar15.mag_catch_fence_out":0.549,"std.ar15.mag_catch_hole_d":0.2055,"std.ar15.mag_catch_slot_bottom_y":-0.689,"std.ar15.mag_catch_slot_floor":0.3799,"std.ar15.mag_catch_slot_front_x":4.557,"std.ar15.mag_catch_slot_h":0.252,"std.ar15.mag_catch_slot_rear_x":3.048,"std.ar15.mag_catch_x":3.291,"std.ar15.mag_catch_y":-0.565,"std.ar15.mag_release_pocket_depth":0.617,"std.ar15.mag_release_pocket_h":0.515,"std.ar15.mag_release_pocket_w":0.319,"std.ar15.magwell_band_bottom_y":-1.959,"std.ar15.magwell_band_front_x":4.549,"std.ar15.magwell_band_proud":0.059,"std.ar15.magwell_band_rear_x":3.975,"std.ar15.magwell_band_side":0.084,"std.ar15.magwell_box_length":2.398,"std.ar15.magwell_corner_r":0.062,"std.ar15.magwell_front_inner_x":6.025,"std.ar15.magwell_length":2.553,"std.ar15.magwell_outside_width":1.098,"std.ar15.magwell_spine_slot_width":0.47,"std.ar15.magwell_width":0.898,"std.ar15.pin_spacing":6.375,"std.ar15.pivot_hole_d":0.251,"std.ar15.rear_lug_slot_depth":0.63,"std.ar15.rear_lug_slot_rear_x":-0.402,"std.ar15.rear_lug_slot_width":0.5,"std.ar15.rear_underside_arc_center_below_seat":0.1928,"std.ar15.rear_underside_arc_center_x":-1.0238,"std.ar15.rear_underside_arc_r":0.75,"std.ar15.rear_underside_round_r":0.44,"std.ar15.rear_wall_arc_r":0.75,"std.ar15.receiver_rear_x":-1.125,"std.ar15.safety_detent_boss_below_deck":0.455,"std.ar15.safety_detent_boss_face":0.53,"std.ar15.safety_detent_boss_from_rear":0.36,"std.ar15.safety_detent_boss_length":0.43,"std.ar15.selector_hole_d":0.376,"std.ar15.takedown_hole_d":0.251,"std.ar15.takedown_spotface_d":0.44,"std.ar15.takedown_spotface_depth":0.04,"std.ar15.trigger_guard_ear_gap":0.442,"std.ar15.trigger_guard_ears_width":0.659,"std.ar15.trigger_guard_front_hole_d":0.1265,"std.ar15.trigger_guard_front_spotface_d":0.25,"std.ar15.trigger_guard_front_spotface_floor":0.3219,"std.ar15.trigger_guard_rear_hole_d":0.1285,"std.ar15.trigger_pin_x":1.928,"std.ar15.trigger_slot_front_ahead_of_pin":0.52,"std.ar15.trigger_slot_length":0.68,"std.ar15.trigger_slot_width":0.312,"std.ar15.upper_rear_face_x":-0.621,"std.receiver_extension.milspec_od":1.148},"profiles":{"side":[[-1.225,1.175],[-1.19,-0.255],[-1.156,-0.474],[-0.811,-0.516],[-0.575,-0.633],[-0.364,-0.86],[-0.297,-0.995],[-0.288,-1.071],[-0.095,-1.079],[-0.095,-1.348],[-0.069,-1.373],[0.924,-1.945],[1.025,-1.995],[1.16,-1.995],[1.177,-2.314],[1.632,-2.314],[1.674,-2.255],[1.673,-2.171],[1.598,-2.078],[1.454,-1.969],[1.404,-1.885],[1.37,-1.784],[1.37,-1.549],[1.454,-1.33],[1.63,-1.153],[1.681,-1.153],[1.832,-1.085],[2.943,-1.084],[3.01,-1.101],[3.128,-1.151],[3.288,-1.311],[3.356,-1.429],[3.389,-1.546],[3.373,-1.849],[3.323,-1.95],[3.264,-1.976],[3.154,-2.102],[3.154,-2.203],[3.264,-2.329],[3.382,-2.329],[3.432,-2.278],[3.466,-2.312],[3.718,-2.295],[4.762,-2.092],[6.091,-1.872],[6.175,-1.838],[6.217,-1.762],[6.133,-1.628],[6.148,-0.483],[6.199,-0.365],[6.308,-0.256],[6.392,-0.205],[6.476,-0.188],[6.602,-0.062],[6.602,0.073],[6.568,0.14],[6.493,0.199],[6.24,0.215],[6.19,0.249],[6.004,0.249],[5.988,0.265],[5.399,0.248],[3.396,0.263],[3.345,0.246],[2.975,0.262],[2.958,0.245],[2.925,0.262],[2.874,0.245],[2.47,0.245],[2.437,0.262],[2.403,0.245],[2.386,0.262],[0.013,0.259],[-0.071,0.276],[-0.307,0.377],[-0.484,0.604],[-0.568,0.89],[-0.568,1.226],[-0.602,1.546],[-0.678,1.605],[-1.032,1.604],[-1.166,1.571]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{}}},"bounds":{"min":[-1.125,-2.329,-0.6986],"max":[6.602,1.5735,0.8]},"volume_in3":5.189,"centroid":[2.4847,-0.6052,0.0291],"shell":[2.8839,-0.6472,0.0093],"area_in2":76.4582,"triangles":24640,"manifold":true,"interior":{"pocket":{"x":[0.24,3.11],"z":0.345,"floor_y":-1.0005},"rear_lug_slot":{"x":[-0.402,0.458],"z":0.25,"floor_y":-0.3815},"safety_detent_boss":{"x":[0.6,1.03],"face_z":0.185,"top_y":-0.2065},"trigger_slot":{"x":[1.768,2.448],"z":0.156},"magazine_well":{"x":[3.472,6.025],"z":0.449}},"holes":{"takedown":{"x":0,"y":0,"d":0.251},"pivot":{"x":6.375,"y":0,"d":0.251},"selector":{"x":0.803,"y":-0.466,"d":0.376},"hammer":{"x":2.771,"y":-0.375,"d":0.1568},"trigger":{"x":1.928,"y":-0.689,"d":0.1568},"guard rear":{"x":1.4985,"y":-2.18,"d":0.1285},"guard front":{"x":3.3425,"y":-2.18,"d":0.1265}},"catches":{"button_pocket":{"x":3.291,"y":-0.565,"floor_z":-0.068,"face_z":0.549},"catch_slot":{"x":[3.048,4.557],"floor_z":-0.3799},"bolt_catch_slot":{"x":[3.203,3.375],"bottom_y":-0.38,"floor_z":-0.4409}},"grip_mount":{"lug":{"seat_y":-1.0695,"x":[-0.075,1.175],"width":0.375,"foot_x":1.0072,"flat_y":-1.9995},"ears":{"width":0.659,"gap":0.442,"gap_top_y":-1.9995,"rear_x":[1.175,1.832],"front_x":[2.943,3.49]},"rear_underside":{"round_r":0.44,"arc_r":0.75,"axis_x":-1.0238,"axis_y":-1.2623}},"rear_walls":{"r":0.75,"centre":[0.122,0.9985],"x":[-0.621,0.122],"meets_face_y":0.8963,"runs_out":[0.055,0.2515],"toe_x":[-0.1255,0.055]},"deck":{"y":0.2485,"x":[-0.02,6.194]},"slabs":[[-1.125,-0.568,-0.696,-0.739,1.573,0.696],[-0.739,-0.926,-0.696,-0.352,1.573,0.696],[-0.352,-1.438,-0.44,0.034,0.418,0.44],[0.034,-1.661,-0.44,0.42,0.254,0.44],[0.42,-1.884,-0.44,0.807,0.249,0.44],[0.807,-2.314,-0.44,1.966,0.249,0.44],[1.966,-1.069,-0.44,2.739,0.249,0.44],[2.739,-1.15,-0.618,3.125,0.249,0.8],[3.125,-2.329,-0.618,3.898,0.249,0.8],[3.898,-2.26,-0.699,4.284,0.249,0.8],[4.284,-2.185,-0.699,4.67,0.249,0.8],[4.67,-2.11,-0.549,5.057,0.249,0.8],[5.057,-2.043,-0.549,5.443,0.249,0.8],[5.443,-1.979,-0.549,5.829,0.249,0.8],[5.829,-1.915,-0.549,6.216,0.249,0.8],[6.216,-1.764,-0.549,6.602,0.249,0.8]],"slots":["receiver"]},"psa-stripped-upper.receiver":{"part":"psa-stripped-upper","component":"receiver","model":"psa-stripped-upper.receiver.glb","script":"psa_stripped_upper.py","inputs":{"psa-stripped-upper.barrel_thread_major_d":1.2442,"psa-stripped-upper.barrel_thread_minor_d":1.1803,"psa-stripped-upper.barrel_thread_tpi":18,"psa-stripped-upper.body_radius":0.59,"psa-stripped-upper.bore_axis_above_pin":0.8775,"psa-stripped-upper.bore_d":1,"psa-stripped-upper.cam_pad_bottom_y":1.05,"psa-stripped-upper.cam_pad_edge_round":0.094,"psa-stripped-upper.cam_pad_face_z":0.5625,"psa-stripped-upper.cam_pad_front_x":5.58,"psa-stripped-upper.cam_pad_rear_x":4.6,"psa-stripped-upper.cam_pad_top_y":1.63,"psa-stripped-upper.charging_handle_above_bore":0.8563,"psa-stripped-upper.deflector_crest_x":2.32,"psa-stripped-upper.deflector_front_out":0.82,"psa-stripped-upper.deflector_out":1.25,"psa-stripped-upper.dovetail_foot_half_width":0.323,"psa-stripped-upper.dovetail_foot_y":1.885,"psa-stripped-upper.fa_axis_angle":20,"psa-stripped-upper.fa_axis_x":-0.395,"psa-stripped-upper.fa_axis_z":1.09,"psa-stripped-upper.fa_bore_d":0.509,"psa-stripped-upper.fa_bore_depth":0.65,"psa-stripped-upper.fa_housing_r":0.3125,"psa-stripped-upper.fa_inner_bore_d":0.315,"psa-stripped-upper.fa_rear_x":-0.53,"psa-stripped-upper.front_face_x":7.036,"psa-stripped-upper.gas_tube_hole_d":0.1835,"psa-stripped-upper.gas_tube_relief_d":0.094,"psa-stripped-upper.gas_tube_relief_offset":0.078,"psa-stripped-upper.handle_seat_x":0.06,"psa-stripped-upper.hinge_axis_y":0.641,"psa-stripped-upper.hinge_axis_z":0.689,"psa-stripped-upper.hinge_boss_r":0.1365,"psa-stripped-upper.hinge_pin_d":0.1295,"psa-stripped-upper.latch_slot_bottom_y":1.52,"psa-stripped-upper.latch_slot_length":0.195,"psa-stripped-upper.latch_slot_top_y":1.935,"psa-stripped-upper.latch_slot_wall":0.156,"psa-stripped-upper.lug_hole_d":0.251,"psa-stripped-upper.lug_rear_face_top_y":0.458,"psa-stripped-upper.lug_wall_half_width":0.453,"psa-stripped-upper.lug_width":0.4945,"psa-stripped-upper.notch_bottom_y":1.6,"psa-stripped-upper.notch_top_y":1.89,"psa-stripped-upper.port_bottom_y":0.841,"psa-stripped-upper.port_end_r":0.25,"psa-stripped-upper.port_front_x":6.036,"psa-stripped-upper.port_length":3.125,"psa-stripped-upper.rail_front_x":6.591,"psa-stripped-upper.rail_neck_bottom_y":1.7,"psa-stripped-upper.rail_neck_half_width":0.309,"psa-stripped-upper.rail_tongue_rear_x":-0.57,"psa-stripped-upper.rail_top_above_pin":2.09,"psa-stripped-upper.rear_flange_front_x":-0.47,"psa-stripped-upper.rear_flange_r":0.6938,"psa-stripped-upper.receiver_rear_x":-0.621,"psa-stripped-upper.right_photo_lens_distance":22,"psa-stripped-upper.right_photo_lens_x":2.58,"psa-stripped-upper.right_photo_lens_y":0.33,"psa-stripped-upper.side_bottom_y":1.44,"psa-stripped-upper.side_half_width":0.319,"psa-stripped-upper.underside_y":0.2485,"std.ar15.bore_axis_y":0.8775,"std.ar15.buffer_tower_front_x":-0.628,"std.ar15.buffer_tower_od":1.392,"std.ar15.buffer_trough_r":0.5625,"std.ar15.charging_handle_channel_floor_y":1.5845,"std.ar15.charging_handle_channel_front_round_x":5.726,"std.ar15.charging_handle_channel_rear_half_width":0.209,"std.ar15.charging_handle_channel_rear_round_x":0.676,"std.ar15.charging_handle_channel_roof_y":1.9085,"std.ar15.charging_handle_channel_round_r":0.2665,"std.ar15.charging_handle_channel_slot_half_width":0.205,"std.ar15.charging_handle_channel_tier_half_width":0.25,"std.ar15.charging_handle_channel_tier_top_y":1.7115,"std.ar15.charging_handle_channel_top_half_width":0.22,"std.ar15.charging_handle_latch_slot_floor":0.045,"std.ar15.charging_handle_notch_chamfer":0.083,"std.ar15.charging_handle_notch_floor_y":1.571,"std.ar15.charging_handle_notch_roof_y":1.89,"std.ar15.deck_y":0.2485,"std.ar15.gas_tube_above_bore":0.78,"std.ar15.pin_spacing":6.375,"std.ar15.rail_tongue_end_r":0.4175,"std.ar15.rail_tongue_fillet_r":0.1476,"std.ar15.rail_tongue_front_x":0.277,"std.ar15.rail_tongue_half_width":0.318,"std.ar15.rail_tongue_shoulder_x":0.4165,"std.ar15.rear_lug_slot_rear_x":-0.402,"std.ar15.rear_lug_slot_width":0.5,"std.ar15.rear_wall_arc_r":0.75,"std.ar15.upper_barrel_thread_length":0.445,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.top_width":0.835},"profiles":{"side":[[-0.621,1.632],[-0.621,0.551],[-0.432,0.408],[-0.282,0.32],[-0.284,-0.141],[-0.269,-0.157],[-0.261,-0.212],[0.231,-0.215],[0.271,-0.176],[0.273,0.063],[0.289,0.078],[0.298,0.245],[0.981,0.241],[0.996,0.257],[3.649,0.243],[3.665,0.258],[6.079,0.245],[6.103,0.221],[6.102,-0.049],[6.133,-0.113],[6.236,-0.185],[6.426,-0.218],[6.554,-0.171],[6.642,-0.068],[6.651,0.242],[6.683,0.258],[6.874,0.256],[6.89,0.272],[6.905,0.256],[6.937,0.256],[6.953,0.272],[6.969,0.256],[7.036,0.306],[7.036,1.434],[7.031,1.455],[6.992,1.479],[6.65,1.473],[6.652,1.791],[6.636,1.806],[6.636,1.886],[6.652,1.902],[6.669,2.013],[6.653,2.029],[6.653,2.076],[6.63,2.1],[6.201,2.103],[6.089,2.04],[6.057,1.992],[6.002,2.016],[6.002,2.08],[5.978,2.104],[5.804,2.105],[5.724,2.042],[5.692,1.994],[5.676,1.994],[5.644,1.995],[5.605,2.035],[5.597,2.106],[5.407,2.107],[5.311,1.996],[5.279,1.997],[5.208,2.021],[5.2,2.108],[5.01,2.109],[4.985,2.054],[5.001,2.038],[4.993,2.03],[4.945,1.999],[4.898,1.999],[4.85,1.999],[4.811,2.023],[4.803,2.11],[4.628,2.111],[4.612,2.016],[4.58,2.001],[4.501,2.001],[4.453,2.001],[4.413,2.025],[4.406,2.113],[4.231,2.114],[4.223,2.026],[4.183,2.003],[4.119,2.003],[4.04,2.004],[4.024,2.019],[4.009,2.115],[3.834,2.116],[3.826,2.029],[3.786,2.005],[3.643,2.006],[3.619,2.03],[3.612,2.117],[3.421,2.118],[3.429,2.031],[3.405,2.007],[3.341,2.007],[3.246,2.008],[3.222,2.032],[3.222,2.08],[3.199,2.119],[3.024,2.12],[3.016,2.017],[2.944,2.01],[2.833,2.01],[2.809,2.034],[2.802,2.122],[2.627,2.123],[2.619,2.035],[2.595,2.012],[2.547,2.012],[2.436,2.012],[2.412,2.036],[2.405,2.124],[2.23,2.125],[2.222,2.053],[2.198,2.014],[2.039,2.015],[1.999,2.055],[2.015,2.07],[2.008,2.126],[1.833,2.127],[1.809,2.103],[1.809,2.04],[1.769,2.016],[1.642,2.017],[1.61,2.033],[1.61,2.128],[1.42,2.129],[1.412,2.058],[1.372,2.018],[1.26,2.019],[1.189,2.043],[1.205,2.059],[1.197,2.13],[-0.534,2.14],[-0.574,2.116],[-0.567,1.934],[-0.487,1.917],[-0.44,1.885],[0.037,1.883],[0.06,1.859],[0.06,1.732],[-0.028,1.629]]},"features":{"side":{"forward_assist_rim":[[[-0.777,1.292],[-0.586,1.291],[-0.59,0.623],[-0.781,0.624]]],"deflector":[[[2.068,1.641],[2.132,1.736],[2.879,1.732],[2.942,1.573],[2.988,1.382],[2.986,1.001],[2.954,0.874],[2.763,0.859],[2.112,0.863],[2.065,0.942]]],"deflector_crest":[[[2.339,1.703],[2.418,1.703],[2.415,1.131],[2.336,1.131]]],"port":[[[2.988,1.382],[6.133,1.365],[6.131,0.872],[2.986,0.89]]],"hinge_rear":[[[2.826,0.827],[2.953,0.826],[2.952,0.524],[2.825,0.525]]],"hinge_front":[[[6.257,0.808],[6.432,0.807],[6.43,0.505],[6.256,0.506]]]}},"placement":{"side":{"plane":"xy","offset":{}}},"bounds":{"min":[-0.6367,-0.21,-0.6938],"max":[7.036,2.09,1.4326]},"volume_in3":4.711,"centroid":[2.9973,1.0005,0.0884],"shell":[3.0124,1.0729,0.0568],"area_in2":82.4166,"triangles":15836,"manifold":true,"rear_corner":{"r":0.75,"centre":[0.122,0.9985],"x":[-0.628,-0.0116],"reach_z":0.696,"trough_r":0.5625},"slabs":[[-0.637,0.249,-0.694,-0.253,2.09,1.433],[-0.253,-0.208,-0.59,0.131,2.09,1.371],[0.131,-0.209,-0.59,0.514,2.09,1.231],[0.514,0.249,-0.59,0.898,1.972,1.092],[0.898,0.249,-0.59,1.281,1.972,0.952],[1.281,0.249,-0.59,1.665,1.972,0.812],[1.665,0.249,-0.59,2.049,1.972,0.673],[2.049,0.249,-0.59,2.432,1.972,1.25],[2.432,0.249,-0.59,2.816,1.972,1.176],[2.816,0.249,-0.59,3.2,1.972,0.924],[3.2,0.249,-0.59,5.885,1.972,0.589],[5.885,-0.21,-0.622,6.652,1.972,0.826],[6.652,0.255,-0.622,7.036,1.5,0.622]],"slots":["receiver"]},"radian-raptor-charging-handle":{"part":"radian-raptor-charging-handle","model":"radian-raptor-charging-handle.glb","script":"radian_raptor_charging_handle.py","inputs":{"radian-raptor-charging-handle.block_front_behind_shoulder":0.112,"radian-raptor-charging-handle.catch_bottom":0.086,"radian-raptor-charging-handle.catch_top":0.217,"radian-raptor-charging-handle.channel_depth":0.25,"radian-raptor-charging-handle.channel_rear_behind_shoulder":0.171,"radian-raptor-charging-handle.channel_width":0.312,"radian-raptor-charging-handle.guide_lug_height":0.119,"radian-raptor-charging-handle.hook_drop":0.275,"radian-raptor-charging-handle.hook_fillet_r":0.187,"radian-raptor-charging-handle.hook_length":0.295,"radian-raptor-charging-handle.latch_height":0.359,"radian-raptor-charging-handle.latch_lift":0.022,"radian-raptor-charging-handle.length":5.895,"radian-raptor-charging-handle.lower_plate_thickness":0.086,"radian-raptor-charging-handle.pin_d":0.06,"radian-raptor-charging-handle.rear_groove_count":5,"radian-raptor-charging-handle.rear_groove_depth":0.021,"radian-raptor-charging-handle.rear_groove_r":0.03,"radian-raptor-charging-handle.shaft_thickness":0.2985,"radian-raptor-charging-handle.shaft_width":0.4,"radian-raptor-charging-handle.t_height":0.4,"radian-raptor-charging-handle.top_chamfer_drop":0.06,"radian-raptor-charging-handle.top_chamfer_from_shoulder":0.226,"radian-raptor-charging-handle.top_chamfer_full_from_shoulder":0.377,"radian-raptor-charging-handle.top_flat_width":0.205,"radian-raptor-charging-handle.upper_plate_thickness":0.176,"std.ar15.charging_handle_axis_y":1.7338,"std.ar15.charging_handle_channel_rear_half_width":0.209,"std.ar15.charging_handle_channel_rear_round_x":0.676,"std.ar15.charging_handle_channel_round_r":0.2665,"std.ar15.charging_handle_latch_slot_bottom_y":1.52,"std.ar15.charging_handle_latch_slot_floor":0.045,"std.ar15.charging_handle_latch_slot_length":0.195,"std.ar15.charging_handle_latch_slot_top_y":1.935,"std.ar15.charging_handle_latch_slot_wall":0.156,"std.ar15.charging_handle_notch_chamfer":0.083,"std.ar15.charging_handle_notch_floor_y":1.571,"std.ar15.charging_handle_notch_roof_y":1.89,"std.ar15.rail_tongue_half_width":0.318},"profiles":{"plan":[[-1.053,0.419],[-1.049,0.415],[-1.053,0.404],[-1.037,0.381],[-1.033,0.388],[-1.023,0.374],[-1.01,0.369],[-1.026,0.367],[-1.033,0.374],[-1.039,0.372],[-1.042,0.228],[-1.037,0.227],[-1.033,0.234],[-1.026,0.234],[-1.024,0.243],[-1.012,0.255],[-1.006,0.254],[-1.014,0.243],[-1.006,0.239],[-1.024,0.221],[-1.021,0.214],[-1.024,0.203],[-1.017,0.196],[-1.028,0.189],[-1.03,0.223],[-1.042,0.21],[-1.042,0.178],[-1.046,0.174],[-1.042,-0.196],[-1.031,-0.221],[-1.031,-0.232],[-1.042,-0.243],[-1.042,-0.289],[-1.035,-0.329],[-1.039,-0.347],[-1.035,-0.35],[-1.035,-0.386],[-1.015,-0.381],[-1.021,-0.39],[-1.014,-0.397],[-1.028,-0.415],[-1.024,-0.419],[-1.028,-0.437],[-1.024,-0.44],[-1.028,-0.462],[-1.031,-0.462],[-1.031,-0.448],[-1.039,-0.433],[-1.031,-0.426],[-1.039,-0.419],[-1.035,-0.408],[-1.042,-0.412],[-1.042,-0.433],[-1.046,-0.437],[-1.042,-0.44],[-1.042,-0.487],[-1.035,-0.534],[-1.028,-0.555],[-1.017,-0.563],[-1.024,-0.566],[-1.005,-0.597],[-0.98,-0.604],[-0.965,-0.629],[-0.96,-0.623],[-0.96,-0.638],[-0.949,-0.649],[-0.953,-0.656],[-0.949,-0.659],[-0.958,-0.661],[-0.96,-0.652],[-0.956,-0.649],[-0.965,-0.647],[-0.964,-0.663],[-0.947,-0.665],[-0.944,-0.661],[-0.928,-0.677],[-0.921,-0.695],[-0.921,-0.713],[-0.912,-0.711],[-0.906,-0.717],[-0.915,-0.722],[-0.922,-0.719],[-0.924,-0.724],[-0.912,-0.737],[-0.905,-0.736],[-0.901,-0.729],[-0.894,-0.733],[-0.881,-0.749],[-0.874,-0.771],[-0.867,-0.767],[-0.871,-0.792],[-0.874,-0.792],[-0.876,-0.783],[-0.878,-0.796],[-0.851,-0.805],[-0.835,-0.821],[-0.831,-0.846],[-0.835,-0.86],[-0.826,-0.869],[-0.801,-0.876],[-0.792,-0.893],[-0.785,-0.896],[-0.792,-0.928],[-0.774,-0.954],[-0.76,-0.964],[-0.763,-0.972],[-0.742,-1.004],[-0.735,-1],[-0.735,-1.015],[-0.713,-1.047],[-0.706,-1.051],[-0.702,-1.065],[-0.684,-1.086],[-0.684,-1.094],[-0.679,-1.088],[-0.674,-1.09],[-0.677,-1.101],[-0.674,-1.108],[-0.643,-1.142],[-0.604,-1.164],[-0.593,-1.16],[-0.597,-1.167],[-0.518,-1.181],[-0.511,-1.178],[-0.504,-1.185],[-0.371,-1.206],[-0.314,-1.22],[-0.267,-1.213],[-0.228,-1.191],[-0.19,-1.146],[-0.179,-1.117],[-0.179,-1.11],[-0.197,-1.092],[-0.197,-1.07],[-0.183,-1.052],[-0.183,-1.042],[-0.192,-1.033],[-0.195,-1.036],[-0.21,-1.033],[-0.226,-1.013],[-0.222,-0.991],[-0.208,-0.977],[-0.212,-0.959],[-0.238,-0.954],[-0.255,-0.934],[-0.251,-0.912],[-0.237,-0.898],[-0.24,-0.88],[-0.264,-0.878],[-0.283,-0.858],[-0.276,-0.83],[-0.265,-0.822],[-0.265,-0.808],[-0.271,-0.799],[-0.296,-0.795],[-0.308,-0.779],[-0.305,-0.754],[-0.29,-0.743],[-0.29,-0.736],[-0.299,-0.72],[-0.321,-0.72],[-0.337,-0.704],[-0.337,-0.682],[-0.319,-0.66],[-0.326,-0.643],[-0.314,-0.637],[-0.312,-0.632],[-0.317,-0.63],[-0.335,-0.641],[-0.35,-0.641],[-0.366,-0.625],[-0.362,-0.596],[-0.337,-0.578],[-0.337,-0.527],[-0.33,-0.491],[-0.312,-0.448],[-0.301,-0.434],[-0.29,-0.401],[-0.285,-0.396],[-0.281,-0.407],[-0.242,-0.374],[-0.217,-0.367],[-0.17,-0.366],[-0.149,-0.374],[-0.124,-0.373],[-0.048,-0.388],[-0.023,-0.387],[0.027,-0.398],[0.099,-0.405],[0.102,-0.409],[0.145,-0.408],[0.149,-0.412],[0.346,-0.397],[0.363,-0.384],[0.363,-0.348],[0.352,-0.319],[0.23,-0.208],[0.235,-0.199],[0.612,-0.197],[0.623,-0.194],[0.627,-0.197],[0.907,-0.196],[0.911,-0.199],[0.947,-0.196],[0.95,-0.199],[1.231,-0.198],[1.238,-0.194],[1.242,-0.198],[1.57,-0.196],[1.573,-0.2],[1.588,-0.196],[1.649,-0.196],[1.653,-0.2],[1.682,-0.196],[1.685,-0.2],[1.757,-0.199],[1.761,-0.196],[1.768,-0.199],[1.779,-0.195],[1.783,-0.199],[2.169,-0.197],[2.176,-0.194],[2.18,-0.197],[2.201,-0.197],[2.22,-0.193],[2.241,-0.197],[2.248,-0.19],[2.252,-0.197],[2.306,-0.197],[2.306,-0.193],[2.295,-0.193],[2.295,-0.19],[2.328,-0.189],[2.332,-0.197],[2.346,-0.197],[2.355,-0.184],[2.346,-0.171],[2.36,-0.175],[2.364,-0.167],[2.404,-0.164],[2.407,-0.167],[2.433,-0.167],[2.44,-0.164],[2.444,-0.167],[2.494,-0.167],[2.5,-0.172],[2.458,-0.174],[2.462,-0.182],[2.476,-0.181],[2.478,-0.187],[2.454,-0.185],[2.463,-0.194],[2.458,-0.2],[3.07,-0.197],[3.081,-0.2],[3.088,-0.197],[3.091,-0.2],[3.095,-0.197],[3.117,-0.197],[3.12,-0.2],[3.153,-0.2],[3.168,-0.196],[3.171,-0.2],[3.236,-0.2],[3.244,-0.196],[3.247,-0.2],[3.305,-0.199],[3.309,-0.196],[3.327,-0.199],[3.325,-0.19],[3.331,-0.188],[3.338,-0.199],[3.367,-0.199],[3.371,-0.195],[3.374,-0.199],[4.493,-0.198],[4.497,-0.201],[4.562,-0.204],[4.595,-0.215],[4.65,-0.244],[4.806,-0.243],[4.81,-0.236],[4.817,-0.243],[4.828,-0.243],[4.89,-0.214],[4.952,-0.199],[5.484,-0.197],[5.488,-0.2],[5.565,-0.2],[5.565,-0.196],[5.55,-0.196],[5.55,-0.193],[5.579,-0.193],[5.583,-0.2],[5.594,-0.203],[5.623,-0.203],[5.634,-0.196],[5.674,-0.199],[5.673,-0.205],[5.678,-0.214],[5.824,-0.217],[5.828,-0.213],[5.842,-0.217],[5.883,-0.202],[5.914,-0.167],[5.936,-0.135],[5.961,-0.069],[5.969,0.004],[5.965,0.007],[5.961,0.051],[5.943,0.102],[5.925,0.131],[5.919,0.129],[5.892,0.156],[5.895,0.167],[5.864,0.187],[5.842,0.187],[5.839,0.19],[5.693,0.19],[5.678,0.175],[5.667,0.175],[5.634,0.186],[5.638,0.193],[5.521,0.196],[5.517,0.2],[5.448,0.199],[5.444,0.188],[5.435,0.194],[5.437,0.199],[4.992,0.197],[4.988,0.2],[4.941,0.2],[4.937,0.204],[4.923,0.204],[4.919,0.196],[4.879,0.211],[4.879,0.214],[4.888,0.216],[4.879,0.222],[4.868,0.225],[4.864,0.218],[4.859,0.223],[4.861,0.229],[4.835,0.243],[4.646,0.242],[4.58,0.209],[4.522,0.198],[3.595,0.197],[3.592,0.2],[3.588,0.197],[3.574,0.2],[3.556,0.197],[3.552,0.2],[3.53,0.2],[3.527,0.196],[3.516,0.2],[3.497,0.196],[3.494,0.2],[3.487,0.196],[3.472,0.2],[2.802,0.196],[2.798,0.2],[2.791,0.196],[2.776,0.2],[2.769,0.196],[2.747,0.2],[2.744,0.196],[2.74,0.2],[2.686,0.199],[2.679,0.196],[2.675,0.199],[2.176,0.197],[2.173,0.2],[2.165,0.2],[2.162,0.193],[2.133,0.2],[2.126,0.196],[2.097,0.2],[2.089,0.193],[2.082,0.2],[2.068,0.196],[2.064,0.2],[1.483,0.197],[1.48,0.189],[1.473,0.197],[1.469,0.193],[1.465,0.197],[1.447,0.193],[1.444,0.2],[1.411,0.193],[1.375,0.2],[1.361,0.196],[1.354,0.2],[0.666,0.196],[0.663,0.2],[0.609,0.196],[0.605,0.199],[0.005,0.2],[0,0.205],[0,0.328],[-0.027,0.351],[-0.045,0.343],[-0.056,0.347],[-0.203,0.346],[-0.206,0.35],[-0.224,0.346],[-0.242,0.35],[-0.237,0.355],[-0.24,0.366],[-0.289,0.414],[-0.292,0.403],[-0.316,0.441],[-0.341,0.506],[-0.348,0.542],[-0.348,0.581],[-0.36,0.587],[-0.373,0.603],[-0.369,0.631],[-0.35,0.644],[-0.335,0.644],[-0.33,0.657],[-0.33,0.664],[-0.341,0.671],[-0.348,0.686],[-0.341,0.711],[-0.321,0.724],[-0.31,0.724],[-0.305,0.733],[-0.305,0.743],[-0.319,0.758],[-0.323,0.776],[-0.307,0.799],[-0.285,0.803],[-0.276,0.819],[-0.294,0.841],[-0.294,0.859],[-0.278,0.879],[-0.256,0.882],[-0.251,0.895],[-0.269,0.924],[-0.265,0.942],[-0.249,0.958],[-0.226,0.964],[-0.226,0.982],[-0.24,0.999],[-0.24,1.021],[-0.221,1.041],[-0.206,1.041],[-0.197,1.054],[-0.197,1.061],[-0.212,1.079],[-0.208,1.108],[-0.188,1.12],[-0.178,1.12],[-0.172,1.129],[-0.172,1.14],[-0.186,1.158],[-0.186,1.176],[-0.17,1.196],[-0.151,1.202],[-0.154,1.241],[-0.165,1.274],[-0.19,1.309],[-0.228,1.336],[-0.278,1.35],[-0.324,1.346],[-0.378,1.331],[-0.536,1.302],[-0.568,1.287],[-0.599,1.26],[-0.602,1.253],[-0.593,1.24],[-0.582,1.251],[-0.57,1.253],[-0.591,1.227],[-0.609,1.195],[-0.616,1.191],[-0.627,1.166],[-0.656,1.13],[-0.659,1.115],[-0.695,1.068],[-0.695,1.061],[-0.717,1.032],[-0.72,1.018],[-0.795,0.906],[-0.803,0.884],[-0.813,0.877],[-0.853,0.805],[-0.867,0.798],[-0.863,0.794],[-0.878,0.772],[-0.878,0.765],[-0.899,0.74],[-0.938,0.675],[-0.942,0.66],[-0.96,0.646],[-0.971,0.617],[-1.003,0.574],[-1.003,0.567],[-1.021,0.538],[-1.021,0.527],[-1.028,0.52],[-1.035,0.484],[-1.031,0.477],[-1.035,0.473],[-1.039,0.412],[-1.046,0.415],[-1.042,0.419],[-1.042,0.455],[-1.046,0.458],[-1.042,0.462],[-1.046,0.469],[-1.039,0.473],[-1.046,0.48],[-1.039,0.48],[-1.039,0.487],[-1.046,0.491],[-1.046,0.505],[-1.049,0.505]]},"features":{"plan":{"windows":[[[-0.777,0.733],[-0.774,0.773],[-0.756,0.809],[-0.538,1.156],[-0.504,1.19],[-0.482,1.201],[-0.432,1.209],[-0.378,1.223],[-0.339,1.224],[-0.314,1.213],[-0.29,1.186],[-0.287,1.136],[-0.402,0.797],[-0.402,0.786],[-0.423,0.728],[-0.441,0.699],[-0.464,0.679],[-0.493,0.669],[-0.522,0.668],[-0.565,0.679],[-0.615,0.679],[-0.686,0.664],[-0.726,0.667],[-0.747,0.678],[-0.763,0.694]],[[-0.763,-0.763],[-0.763,-0.727],[-0.756,-0.709],[-0.74,-0.689],[-0.693,-0.667],[-0.672,-0.667],[-0.611,-0.681],[-0.547,-0.681],[-0.525,-0.674],[-0.475,-0.674],[-0.446,-0.684],[-0.427,-0.701],[-0.405,-0.74],[-0.402,-0.762],[-0.394,-0.772],[-0.312,-1.01],[-0.312,-1.042],[-0.319,-1.06],[-0.332,-1.076],[-0.364,-1.094],[-0.403,-1.095],[-0.529,-1.07],[-0.575,-1.052],[-0.599,-1.029],[-0.631,-0.975],[-0.727,-0.835],[-0.727,-0.828],[-0.738,-0.817],[-0.756,-0.784]]],"catch_gap":[[[0,-0.263],[0,-0.205],[0.016,-0.2],[0.181,-0.199],[0.187,-0.241],[0.194,-0.259],[0.187,-0.284],[0.17,-0.297],[0.113,-0.3],[0.109,-0.304],[0.034,-0.294],[0.005,-0.283],[0.011,-0.277],[0.011,-0.259],[0.005,-0.258]]],"pins":[[[-0.595,0.433],[-0.584,0.433],[-0.584,0.423],[-0.595,0.423]],[[-0.588,-0.422],[-0.578,-0.422],[-0.578,-0.433],[-0.588,-0.433]]],"plate":[[[-1.072,0.198],[-1.046,0.222],[-1.03,0.238],[-1.002,0.25],[-0.951,0.264],[-0.898,0.278],[-0.844,0.293],[-0.798,0.307],[-0.765,0.326],[-0.742,0.354],[-0.724,0.391],[-0.71,0.438],[-0.697,0.485],[-0.678,0.522],[-0.651,0.546],[-0.614,0.557],[-0.567,0.558],[-0.525,0.544],[-0.49,0.519],[-0.464,0.482],[-0.45,0.44],[-0.447,0.398],[-0.456,0.361],[-0.475,0.333],[-0.503,0.323],[-0.542,0.309],[-0.583,0.288],[-0.628,0.253],[-0.667,0.206],[-0.697,0.154],[-0.719,0.084],[-0.726,-0.001],[-0.718,-0.085],[-0.694,-0.155],[-0.664,-0.206],[-0.624,-0.252],[-0.579,-0.287],[-0.537,-0.308],[-0.498,-0.321],[-0.47,-0.33],[-0.451,-0.358],[-0.441,-0.395],[-0.443,-0.437],[-0.457,-0.479],[-0.482,-0.516],[-0.517,-0.542],[-0.559,-0.557],[-0.605,-0.557],[-0.643,-0.546],[-0.67,-0.523],[-0.689,-0.485],[-0.704,-0.439],[-0.718,-0.393],[-0.737,-0.356],[-0.76,-0.328],[-0.793,-0.309],[-0.84,-0.296],[-0.893,-0.282],[-0.947,-0.269],[-0.998,-0.255],[-1.026,-0.244],[-1.043,-0.228],[-1.068,-0.205]]],"opening":[[[-1.092,0.402],[-1.015,0.399],[-0.945,0.39],[-0.882,0.388],[-0.829,0.395],[-0.789,0.414],[-0.762,0.447],[-0.743,0.491],[-0.725,0.538],[-0.697,0.573],[-0.66,0.597],[-0.609,0.604],[-0.558,0.602],[-0.512,0.589],[-0.469,0.563],[-0.434,0.524],[-0.41,0.478],[-0.399,0.424],[-0.403,0.378],[-0.421,0.343],[-0.449,0.319],[-0.444,-0.316],[-0.416,-0.339],[-0.397,-0.374],[-0.392,-0.42],[-0.403,-0.474],[-0.426,-0.521],[-0.461,-0.561],[-0.503,-0.586],[-0.549,-0.601],[-0.6,-0.603],[-0.652,-0.597],[-0.689,-0.574],[-0.717,-0.539],[-0.736,-0.493],[-0.755,-0.449],[-0.783,-0.416],[-0.823,-0.398],[-0.876,-0.391],[-0.939,-0.394],[-1.009,-0.404],[-1.085,-0.409]]],"block":[[[-0.475,0.333],[-0.503,0.323],[-0.542,0.309],[-0.583,0.288],[-0.628,0.253],[-0.667,0.206],[-0.697,0.154],[-0.719,0.084],[-0.726,-0.001],[-0.718,-0.085],[-0.694,-0.155],[-0.664,-0.206],[-0.624,-0.252],[-0.579,-0.287],[-0.537,-0.308],[-0.498,-0.321],[-0.47,-0.33],[-0.439,-0.356],[-0.23,-0.37],[0.282,-0.366],[0.277,0.35],[-0.445,0.345]]],"logo":[[[-0.442,0.085],[-0.37,0.061],[-0.258,0.118],[-0.257,-0.001],[-0.193,-0.055],[-0.195,0.232]],[[-0.58,0.002],[-0.354,-0.06],[-0.191,-0.224],[-0.192,-0.14],[-0.328,0],[-0.51,0.043]]],"rear_grooves":[[[-0.982,0.632],[-0.972,0.632],[-0.972,0.621],[-0.982,0.621]],[[-0.936,0.702],[-0.926,0.702],[-0.926,0.691],[-0.936,0.691]],[[-0.89,0.772],[-0.879,0.772],[-0.879,0.761],[-0.89,0.761]],[[-0.847,0.843],[-0.836,0.843],[-0.836,0.832],[-0.847,0.832]],[[-0.805,0.915],[-0.795,0.915],[-0.795,0.904],[-0.805,0.904]],[[-0.973,-0.629],[-0.962,-0.629],[-0.962,-0.64],[-0.973,-0.64]],[[-0.926,-0.693],[-0.915,-0.693],[-0.915,-0.704],[-0.926,-0.704]],[[-0.879,-0.765],[-0.868,-0.765],[-0.868,-0.776],[-0.879,-0.776]],[[-0.832,-0.835],[-0.821,-0.835],[-0.821,-0.846],[-0.832,-0.846]],[[-0.789,-0.904],[-0.779,-0.904],[-0.779,-0.915],[-0.789,-0.915]]]}},"placement":{"plan":{"plane":"xz","offset":{}}},"bounds":{"min":[-1.039,-0.4243,-1.22],"max":[5.895,0.2508,1.35]},"volume_in3":0.7762,"centroid":[0.8579,0.025,-0.0007],"shell":[1.4177,0.0197,0.0054],"area_in2":19.6145,"triangles":20702,"manifold":true,"slabs":[[-1.039,-0.149,-1.13,-0.654,0.251,1.133],[-0.654,-0.149,-1.22,0.117,0.254,1.35],[0.117,-0.149,-0.412,0.502,0.149,0.2],[0.502,-0.176,-0.244,5.51,0.149,0.243],[5.51,-0.424,-0.217,5.895,0.149,0.2]],"slots":["body","latches","pins","marking"]},"radian-raptor-lt-charging-handle":{"part":"radian-raptor-lt-charging-handle","model":"radian-raptor-lt-charging-handle.glb","script":"radian_raptor_lt_charging_handle.py","inputs":{"radian-raptor-lt-charging-handle.block_front_behind_shoulder":0.112,"radian-raptor-lt-charging-handle.catch_bottom":0.086,"radian-raptor-lt-charging-handle.catch_top":0.217,"radian-raptor-lt-charging-handle.channel_depth":0.25,"radian-raptor-lt-charging-handle.channel_rear_behind_shoulder":0.171,"radian-raptor-lt-charging-handle.channel_width":0.312,"radian-raptor-lt-charging-handle.front_groove_count":7,"radian-raptor-lt-charging-handle.front_groove_count_left":6,"radian-raptor-lt-charging-handle.front_groove_depth":0.024,"radian-raptor-lt-charging-handle.front_groove_width":0.043,"radian-raptor-lt-charging-handle.guide_lug_height":0.119,"radian-raptor-lt-charging-handle.hook_drop":0.275,"radian-raptor-lt-charging-handle.hook_fillet_r":0.187,"radian-raptor-lt-charging-handle.hook_length":0.295,"radian-raptor-lt-charging-handle.latch_height":0.37,"radian-raptor-lt-charging-handle.latch_lift":0.045,"radian-raptor-lt-charging-handle.length":5.895,"radian-raptor-lt-charging-handle.lower_plate_thickness":0.086,"radian-raptor-lt-charging-handle.panel_depth":0.075,"radian-raptor-lt-charging-handle.pin_d":0.06,"radian-raptor-lt-charging-handle.rear_rib_count":5,"radian-raptor-lt-charging-handle.rear_rib_height":0.015,"radian-raptor-lt-charging-handle.rear_rib_r":0.012,"radian-raptor-lt-charging-handle.shaft_thickness":0.2985,"radian-raptor-lt-charging-handle.shaft_width":0.4,"radian-raptor-lt-charging-handle.t_height":0.4,"radian-raptor-lt-charging-handle.top_chamfer_drop":0.06,"radian-raptor-lt-charging-handle.top_chamfer_from_shoulder":0.226,"radian-raptor-lt-charging-handle.top_chamfer_full_from_shoulder":0.377,"radian-raptor-lt-charging-handle.top_flat_width":0.205,"radian-raptor-lt-charging-handle.upper_plate_thickness":0.176,"std.ar15.charging_handle_axis_y":1.7338,"std.ar15.charging_handle_channel_rear_half_width":0.209,"std.ar15.charging_handle_channel_rear_round_x":0.676,"std.ar15.charging_handle_channel_round_r":0.2665,"std.ar15.charging_handle_latch_slot_bottom_y":1.52,"std.ar15.charging_handle_latch_slot_floor":0.045,"std.ar15.charging_handle_latch_slot_length":0.195,"std.ar15.charging_handle_latch_slot_top_y":1.935,"std.ar15.charging_handle_latch_slot_wall":0.156,"std.ar15.charging_handle_notch_chamfer":0.083,"std.ar15.charging_handle_notch_floor_y":1.571,"std.ar15.charging_handle_notch_roof_y":1.89,"std.ar15.rail_tongue_half_width":0.318},"profiles":{"plan":[[-1.059,0.462],[-1.055,0.433],[-1.059,0.419],[-1.048,0.39],[-1.034,0.375],[-1.045,0.321],[-1.045,0.202],[-1.048,0.199],[-1.048,-0.187],[-1.037,-0.227],[-1.048,-0.241],[-1.048,-0.292],[-1.045,-0.295],[-1.045,-0.331],[-1.03,-0.364],[-1.03,-0.386],[-1.045,-0.396],[-1.052,-0.411],[-1.055,-0.447],[-1.052,-0.451],[-1.045,-0.53],[-1.034,-0.566],[-1.01,-0.604],[-0.985,-0.607],[-0.973,-0.616],[-0.958,-0.642],[-0.962,-0.674],[-0.953,-0.683],[-0.931,-0.683],[-0.911,-0.707],[-0.904,-0.721],[-0.904,-0.732],[-0.911,-0.743],[-0.908,-0.753],[-0.895,-0.763],[-0.884,-0.759],[-0.877,-0.763],[-0.865,-0.775],[-0.85,-0.8],[-0.857,-0.815],[-0.854,-0.833],[-0.848,-0.838],[-0.823,-0.842],[-0.807,-0.862],[-0.8,-0.876],[-0.803,-0.909],[-0.791,-0.918],[-0.773,-0.918],[-0.753,-0.941],[-0.746,-0.956],[-0.753,-0.974],[-0.749,-0.992],[-0.706,-1.049],[-0.677,-1.1],[-0.636,-1.149],[-0.614,-1.163],[-0.567,-1.177],[-0.549,-1.177],[-0.459,-1.199],[-0.304,-1.224],[-0.272,-1.217],[-0.243,-1.203],[-0.218,-1.181],[-0.186,-1.163],[-0.151,-1.129],[-0.137,-1.1],[-0.133,-1.082],[-0.133,-1.053],[-0.139,-1.044],[-0.153,-1.044],[-0.157,-1.051],[-0.164,-1.051],[-0.173,-1.06],[-0.166,-1.064],[-0.173,-1.071],[-0.175,-1.087],[-0.177,-1.071],[-0.184,-1.064],[-0.177,-1.053],[-0.186,-1.051],[-0.196,-1.062],[-0.204,-1.062],[-0.223,-1.028],[-0.207,-1.012],[-0.193,-1.008],[-0.187,-1.013],[-0.184,-0.999],[-0.166,-0.977],[-0.166,-0.963],[-0.182,-0.957],[-0.189,-0.972],[-0.193,-0.968],[-0.2,-0.975],[-0.211,-0.972],[-0.214,-0.979],[-0.223,-0.974],[-0.222,-0.965],[-0.229,-0.972],[-0.243,-0.975],[-0.259,-0.945],[-0.259,-0.934],[-0.25,-0.925],[-0.229,-0.921],[-0.222,-0.914],[-0.22,-0.927],[-0.213,-0.927],[-0.216,-0.905],[-0.205,-0.894],[-0.205,-0.876],[-0.218,-0.871],[-0.25,-0.892],[-0.259,-0.887],[-0.258,-0.882],[-0.279,-0.885],[-0.288,-0.876],[-0.288,-0.865],[-0.295,-0.858],[-0.295,-0.844],[-0.29,-0.838],[-0.265,-0.831],[-0.238,-0.804],[-0.238,-0.79],[-0.25,-0.781],[-0.254,-0.788],[-0.272,-0.795],[-0.279,-0.795],[-0.286,-0.788],[-0.308,-0.795],[-0.317,-0.79],[-0.317,-0.779],[-0.324,-0.768],[-0.324,-0.75],[-0.312,-0.741],[-0.297,-0.741],[-0.288,-0.732],[-0.292,-0.725],[-0.286,-0.719],[-0.279,-0.723],[-0.272,-0.719],[-0.263,-0.707],[-0.267,-0.699],[-0.276,-0.694],[-0.283,-0.708],[-0.294,-0.701],[-0.308,-0.716],[-0.31,-0.703],[-0.304,-0.694],[-0.322,-0.701],[-0.337,-0.701],[-0.346,-0.685],[-0.35,-0.663],[-0.346,-0.656],[-0.321,-0.642],[-0.328,-0.613],[-0.322,-0.607],[-0.31,-0.609],[-0.317,-0.624],[-0.317,-0.638],[-0.308,-0.64],[-0.304,-0.647],[-0.303,-0.638],[-0.31,-0.634],[-0.306,-0.624],[-0.31,-0.616],[-0.304,-0.615],[-0.297,-0.625],[-0.285,-0.62],[-0.29,-0.6],[-0.297,-0.604],[-0.322,-0.6],[-0.351,-0.607],[-0.357,-0.602],[-0.36,-0.584],[-0.357,-0.562],[-0.348,-0.553],[-0.33,-0.546],[-0.319,-0.528],[-0.313,-0.53],[-0.312,-0.539],[-0.301,-0.524],[-0.294,-0.528],[-0.288,-0.523],[-0.281,-0.494],[-0.281,-0.472],[-0.267,-0.432],[-0.276,-0.423],[-0.285,-0.44],[-0.281,-0.443],[-0.297,-0.449],[-0.295,-0.461],[-0.304,-0.467],[-0.31,-0.461],[-0.31,-0.447],[-0.303,-0.44],[-0.299,-0.425],[-0.281,-0.414],[-0.295,-0.407],[-0.268,-0.391],[-0.258,-0.391],[-0.25,-0.384],[-0.236,-0.38],[-0.178,-0.38],[-0.135,-0.387],[-0.099,-0.387],[-0.063,-0.394],[0.11,-0.409],[0.114,-0.412],[0.186,-0.412],[0.189,-0.409],[0.236,-0.409],[0.24,-0.405],[0.351,-0.398],[0.368,-0.382],[0.357,-0.328],[0.222,-0.199],[0.243,-0.199],[0.247,-0.196],[0.258,-0.199],[0.323,-0.196],[0.326,-0.199],[0.38,-0.199],[0.388,-0.196],[0.391,-0.199],[0.402,-0.196],[0.409,-0.199],[0.424,-0.196],[0.427,-0.199],[0.431,-0.196],[1.051,-0.196],[1.058,-0.199],[1.066,-0.196],[1.069,-0.199],[4.529,-0.198],[4.595,-0.213],[4.663,-0.245],[4.794,-0.245],[4.805,-0.242],[4.819,-0.245],[4.823,-0.242],[4.848,-0.242],[4.903,-0.213],[4.964,-0.198],[5.53,-0.198],[5.533,-0.194],[5.577,-0.194],[5.581,-0.198],[5.649,-0.198],[5.664,-0.194],[5.678,-0.202],[5.711,-0.202],[5.715,-0.205],[5.849,-0.205],[5.882,-0.191],[5.912,-0.16],[5.942,-0.116],[5.967,-0.044],[5.971,0.018],[5.963,0.061],[5.938,0.123],[5.92,0.152],[5.885,0.186],[5.863,0.197],[5.686,0.197],[5.675,0.186],[5.66,0.186],[5.62,0.2],[5.617,0.197],[5.602,0.2],[5.595,0.197],[5.588,0.2],[4.953,0.2],[4.892,0.214],[4.841,0.243],[4.649,0.243],[4.591,0.214],[4.533,0.2],[0.452,0.198],[0.449,0.201],[0.005,0.201],[0,0.206],[0,0.326],[0.011,0.326],[0.007,0.34],[-0.009,0.349],[-0.218,0.349],[-0.236,0.352],[-0.238,0.362],[-0.254,0.378],[-0.272,0.389],[-0.283,0.403],[-0.295,0.405],[-0.303,0.43],[-0.313,0.437],[-0.321,0.459],[-0.328,0.466],[-0.331,0.499],[-0.339,0.509],[-0.339,0.578],[-0.364,0.603],[-0.36,0.636],[-0.351,0.645],[-0.33,0.641],[-0.321,0.647],[-0.328,0.654],[-0.328,0.679],[-0.346,0.69],[-0.342,0.726],[-0.333,0.739],[-0.312,0.742],[-0.306,0.748],[-0.31,0.751],[-0.303,0.758],[-0.301,0.771],[-0.288,0.769],[-0.29,0.775],[-0.312,0.775],[-0.321,0.784],[-0.324,0.794],[-0.317,0.816],[-0.308,0.832],[-0.297,0.836],[-0.286,0.836],[-0.279,0.829],[-0.281,0.841],[-0.274,0.849],[-0.277,0.859],[-0.263,0.863],[-0.283,0.868],[-0.295,0.877],[-0.285,0.917],[-0.276,0.923],[-0.254,0.919],[-0.256,0.924],[-0.245,0.939],[-0.245,0.95],[-0.24,0.955],[-0.231,0.953],[-0.236,0.962],[-0.243,0.959],[-0.263,0.971],[-0.252,1.007],[-0.218,1.016],[-0.211,1.031],[-0.209,1.022],[-0.196,1.009],[-0.182,1.013],[-0.173,1.022],[-0.178,1.035],[-0.182,1.031],[-0.207,1.053],[-0.222,1.053],[-0.231,1.062],[-0.231,1.069],[-0.211,1.103],[-0.196,1.099],[-0.177,1.112],[-0.18,1.127],[-0.177,1.13],[-0.189,1.136],[-0.195,1.148],[-0.187,1.177],[-0.171,1.19],[-0.157,1.175],[-0.144,1.181],[-0.155,1.188],[-0.155,1.195],[-0.151,1.206],[-0.144,1.21],[-0.144,1.217],[-0.151,1.238],[-0.159,1.242],[-0.159,1.257],[-0.173,1.285],[-0.211,1.323],[-0.276,1.348],[-0.348,1.341],[-0.409,1.323],[-0.434,1.323],[-0.467,1.312],[-0.485,1.312],[-0.546,1.298],[-0.578,1.283],[-0.605,1.256],[-0.771,0.992],[-0.774,0.971],[-0.767,0.956],[-0.774,0.938],[-0.794,0.915],[-0.816,0.915],[-0.825,0.906],[-0.818,0.873],[-0.829,0.859],[-0.832,0.845],[-0.845,0.835],[-0.863,0.835],[-0.872,0.83],[-0.875,0.816],[-0.868,0.794],[-0.892,0.756],[-0.913,0.756],[-0.926,0.743],[-0.919,0.715],[-0.937,0.682],[-0.946,0.677],[-0.964,0.677],[-0.976,0.664],[-0.969,0.646],[-0.969,0.632],[-0.983,0.606],[-0.996,0.597],[-1.018,0.597],[-1.03,0.581],[-1.052,0.52],[-1.055,0.466]]},"features":{"plan":{"catch_gap":[[[0,-0.259],[0,-0.205],[0.005,-0.2],[0.023,-0.196],[0.11,-0.196],[0.114,-0.2],[0.124,-0.196],[0.182,-0.196],[0.18,-0.216],[0.191,-0.255],[0.184,-0.284],[0.175,-0.293],[0.157,-0.301],[0.114,-0.301],[0.11,-0.304],[0.074,-0.301],[0.013,-0.286],[0.014,-0.255],[0.005,-0.261]]],"pins":[[[-0.61,0.44],[-0.599,0.44],[-0.599,0.429],[-0.61,0.429]],[[-0.601,-0.419],[-0.59,-0.419],[-0.59,-0.43],[-0.601,-0.43]]],"plate":[[[-1.086,0.203],[-1.06,0.227],[-1.044,0.243],[-1.016,0.255],[-0.965,0.269],[-0.912,0.283],[-0.858,0.298],[-0.812,0.312],[-0.779,0.331],[-0.756,0.359],[-0.738,0.396],[-0.724,0.443],[-0.711,0.49],[-0.692,0.527],[-0.665,0.551],[-0.628,0.562],[-0.581,0.563],[-0.539,0.549],[-0.504,0.524],[-0.478,0.487],[-0.464,0.445],[-0.461,0.403],[-0.47,0.366],[-0.489,0.338],[-0.517,0.328],[-0.556,0.314],[-0.597,0.293],[-0.642,0.258],[-0.681,0.211],[-0.711,0.159],[-0.733,0.089],[-0.74,0.004],[-0.732,-0.08],[-0.708,-0.15],[-0.678,-0.201],[-0.638,-0.247],[-0.593,-0.282],[-0.551,-0.303],[-0.512,-0.316],[-0.484,-0.325],[-0.465,-0.353],[-0.455,-0.39],[-0.457,-0.432],[-0.471,-0.474],[-0.496,-0.511],[-0.531,-0.537],[-0.573,-0.552],[-0.619,-0.552],[-0.657,-0.541],[-0.684,-0.518],[-0.703,-0.48],[-0.718,-0.434],[-0.732,-0.388],[-0.751,-0.351],[-0.774,-0.323],[-0.807,-0.304],[-0.854,-0.291],[-0.907,-0.277],[-0.961,-0.264],[-1.012,-0.25],[-1.04,-0.239],[-1.057,-0.223],[-1.082,-0.2]]],"opening":[[[-1.084,0.002],[-1.086,0.378],[-1.038,0.38],[-0.99,0.381],[-0.942,0.383],[-0.894,0.391],[-0.87,0.4],[-0.846,0.413],[-0.822,0.427],[-0.798,0.451],[-0.781,0.476],[-0.769,0.5],[-0.76,0.524],[-0.75,0.543],[-0.738,0.563],[-0.722,0.577],[-0.702,0.584],[-0.678,0.589],[-0.642,0.592],[-0.606,0.59],[-0.57,0.583],[-0.534,0.573],[-0.51,0.562],[-0.486,0.545],[-0.467,0.526],[-0.449,0.502],[-0.435,0.478],[-0.423,0.454],[-0.413,0.43],[-0.406,0.406],[-0.391,0.382],[-0.367,0.363],[-0.341,0.353],[-0.336,-0.34],[-0.362,-0.349],[-0.386,-0.369],[-0.401,-0.393],[-0.408,-0.417],[-0.417,-0.441],[-0.429,-0.465],[-0.444,-0.489],[-0.46,-0.514],[-0.479,-0.533],[-0.503,-0.55],[-0.527,-0.562],[-0.563,-0.572],[-0.599,-0.579],[-0.635,-0.582],[-0.671,-0.58],[-0.695,-0.575],[-0.715,-0.568],[-0.732,-0.554],[-0.744,-0.535],[-0.753,-0.515],[-0.763,-0.491],[-0.775,-0.467],[-0.793,-0.444],[-0.817,-0.419],[-0.841,-0.405],[-0.865,-0.393],[-0.889,-0.384],[-0.937,-0.377],[-0.985,-0.375],[-1.033,-0.375],[-1.081,-0.373],[-1.084,0.002]]],"block":[[[-0.489,0.338],[-0.517,0.328],[-0.556,0.314],[-0.597,0.293],[-0.642,0.258],[-0.681,0.211],[-0.711,0.159],[-0.733,0.089],[-0.74,0.004],[-0.732,-0.08],[-0.708,-0.15],[-0.678,-0.201],[-0.638,-0.247],[-0.593,-0.282],[-0.551,-0.303],[-0.512,-0.316],[-0.484,-0.325],[-0.453,-0.351],[-0.244,-0.365],[0.268,-0.361],[0.263,0.355],[-0.459,0.35]]],"logo":[[[-0.471,0.073],[-0.387,0.05],[-0.286,0.111],[-0.285,-0.002],[-0.22,-0.067],[-0.222,0.222]],[[-0.615,-0.004],[-0.545,0.037],[-0.367,-0.005],[-0.338,-0.027],[-0.219,-0.141],[-0.219,-0.237],[-0.386,-0.07]]],"panels":[[[-0.787,0.673],[-0.679,0.673],[-0.583,0.679],[-0.523,0.675],[-0.499,0.689],[-0.48,0.718],[-0.451,0.79],[-0.416,0.887],[-0.375,0.983],[-0.34,1.08],[-0.316,1.152],[-0.321,1.195],[-0.351,1.219],[-0.406,1.226],[-0.478,1.216],[-0.533,1.186],[-0.605,1.126],[-0.674,1.005],[-0.752,0.885],[-0.824,0.764],[-0.843,0.72],[-0.833,0.687]],[[-0.821,-0.703],[-0.802,-0.775],[-0.76,-0.847],[-0.711,-0.919],[-0.663,-0.991],[-0.62,-1.05],[-0.584,-1.092],[-0.548,-1.11],[-0.476,-1.115],[-0.404,-1.115],[-0.35,-1.103],[-0.331,-1.079],[-0.344,-1.036],[-0.374,-0.965],[-0.407,-0.893],[-0.441,-0.821],[-0.472,-0.749],[-0.488,-0.701],[-0.508,-0.683],[-0.574,-0.689],[-0.647,-0.687],[-0.707,-0.678],[-0.761,-0.669],[-0.803,-0.676]]],"front_grooves":[[[-0.324,0.607],[-0.313,0.607],[-0.313,0.596],[-0.324,0.596]],[[-0.299,0.697],[-0.289,0.697],[-0.289,0.687],[-0.299,0.687]],[[-0.276,0.788],[-0.265,0.788],[-0.265,0.777],[-0.276,0.777]],[[-0.251,0.881],[-0.24,0.881],[-0.24,0.87],[-0.251,0.87]],[[-0.226,0.974],[-0.215,0.974],[-0.215,0.963],[-0.226,0.963]],[[-0.203,1.062],[-0.192,1.062],[-0.192,1.052],[-0.203,1.051]],[[-0.179,1.153],[-0.168,1.153],[-0.168,1.142],[-0.179,1.142]],[[-0.324,-0.563],[-0.313,-0.563],[-0.313,-0.573],[-0.324,-0.573]],[[-0.3,-0.656],[-0.289,-0.656],[-0.289,-0.667],[-0.3,-0.667]],[[-0.276,-0.752],[-0.265,-0.752],[-0.265,-0.763],[-0.276,-0.763]],[[-0.253,-0.842],[-0.242,-0.842],[-0.242,-0.853],[-0.253,-0.853]],[[-0.23,-0.933],[-0.219,-0.933],[-0.219,-0.944],[-0.23,-0.944]],[[-0.208,-1.022],[-0.197,-1.022],[-0.197,-1.033],[-0.208,-1.033]]],"rear_ribs":[[[-1.006,0.665],[-0.996,0.665],[-0.996,0.654],[-1.006,0.654]],[[-0.957,0.754],[-0.946,0.754],[-0.946,0.743],[-0.957,0.743]],[[-0.904,0.834],[-0.893,0.834],[-0.893,0.823],[-0.904,0.823]],[[-0.859,0.911],[-0.848,0.911],[-0.848,0.9],[-0.859,0.9]],[[-0.807,0.991],[-0.796,0.991],[-0.796,0.98],[-0.807,0.98]],[[-0.991,-0.667],[-0.98,-0.667],[-0.98,-0.678],[-0.991,-0.678]],[[-0.938,-0.748],[-0.927,-0.748],[-0.927,-0.759],[-0.938,-0.759]],[[-0.882,-0.827],[-0.871,-0.827],[-0.871,-0.838],[-0.882,-0.838]],[[-0.826,-0.907],[-0.815,-0.907],[-0.815,-0.918],[-0.826,-0.918]],[[-0.773,-0.983],[-0.762,-0.983],[-0.762,-0.994],[-0.773,-0.994]]]}},"placement":{"plan":{"plane":"xz","offset":{}}},"bounds":{"min":[-1.0521,-0.4243,-1.224],"max":[5.895,0.2657,1.348]},"volume_in3":0.9036,"centroid":[0.6769,0.0343,0.0168],"shell":[1.4548,0.0294,0.0098],"area_in2":19.035,"triangles":16958,"manifold":true,"slabs":[[-1.052,-0.149,-1.113,-0.666,0.266,1.159],[-0.666,-0.152,-1.224,0.106,0.266,1.348],[0.106,-0.149,-0.412,0.492,0.149,0.2],[0.492,-0.176,-0.245,5.509,0.149,0.243],[5.509,-0.424,-0.205,5.895,0.149,0.2]],"slots":["body","latches","pins","marking"]},"radian-raptor-sd-charging-handle":{"part":"radian-raptor-sd-charging-handle","model":"radian-raptor-sd-charging-handle.glb","script":"radian_raptor_sd_charging_handle.py","inputs":{"radian-raptor-sd-charging-handle.block_front_behind_shoulder":0.107,"radian-raptor-sd-charging-handle.catch_bottom":0.086,"radian-raptor-sd-charging-handle.catch_top":0.217,"radian-raptor-sd-charging-handle.channel_depth":0.25,"radian-raptor-sd-charging-handle.channel_rear_behind_shoulder":0.106,"radian-raptor-sd-charging-handle.channel_width":0.312,"radian-raptor-sd-charging-handle.guide_lug_height":0.119,"radian-raptor-sd-charging-handle.hook_drop":0.275,"radian-raptor-sd-charging-handle.hook_fillet_r":0.187,"radian-raptor-sd-charging-handle.hook_length":0.295,"radian-raptor-sd-charging-handle.latch_lift":0,"radian-raptor-sd-charging-handle.length":5.895,"radian-raptor-sd-charging-handle.lower_plate_thickness":0.086,"radian-raptor-sd-charging-handle.pin_d":0.065,"radian-raptor-sd-charging-handle.plate_arc_behind_pins":0.099,"radian-raptor-sd-charging-handle.plate_arc_r":0.346,"radian-raptor-sd-charging-handle.plate_ear_r":0.105,"radian-raptor-sd-charging-handle.port_count":6,"radian-raptor-sd-charging-handle.port_floor_front":0.092,"radian-raptor-sd-charging-handle.port_floor_rear":0.138,"radian-raptor-sd-charging-handle.port_hole_d":0.115,"radian-raptor-sd-charging-handle.port_notch_depth":0.116,"radian-raptor-sd-charging-handle.port_pitch":0.4425,"radian-raptor-sd-charging-handle.port_top_front":0.19,"radian-raptor-sd-charging-handle.port_top_rear":0.059,"radian-raptor-sd-charging-handle.shaft_thickness":0.2985,"radian-raptor-sd-charging-handle.shaft_width":0.4,"radian-raptor-sd-charging-handle.t_height":0.403,"std.ar15.charging_handle_axis_y":1.7338,"std.ar15.charging_handle_channel_rear_half_width":0.209,"std.ar15.charging_handle_channel_rear_round_x":0.676,"std.ar15.charging_handle_channel_round_r":0.2665,"std.ar15.charging_handle_latch_slot_bottom_y":1.52,"std.ar15.charging_handle_latch_slot_floor":0.045,"std.ar15.charging_handle_latch_slot_length":0.195,"std.ar15.charging_handle_latch_slot_top_y":1.935,"std.ar15.charging_handle_latch_slot_wall":0.156,"std.ar15.charging_handle_notch_chamfer":0.083,"std.ar15.charging_handle_notch_floor_y":1.571,"std.ar15.charging_handle_notch_roof_y":1.89,"std.ar15.rail_tongue_half_width":0.318},"profiles":{"plan":[[-1.083,-0.252],[-1.076,-0.263],[-1.083,-0.267],[-1.079,-0.274],[-1.083,-0.277],[-1.079,-0.281],[-1.076,-0.361],[-1.069,-0.393],[-1.076,-0.411],[-1.076,-0.469],[-1.072,-0.473],[-1.072,-0.513],[-1.061,-0.564],[-1.047,-0.593],[-1.03,-0.609],[-1.027,-0.605],[-1.012,-0.609],[-0.996,-0.625],[-0.992,-0.658],[-0.996,-0.669],[-0.987,-0.678],[-0.968,-0.678],[-0.948,-0.698],[-0.945,-0.719],[-0.952,-0.738],[-0.947,-0.743],[-0.928,-0.743],[-0.905,-0.763],[-0.901,-0.792],[-0.905,-0.806],[-0.899,-0.812],[-0.885,-0.812],[-0.87,-0.819],[-0.857,-0.835],[-0.861,-0.872],[-0.857,-0.879],[-0.834,-0.884],[-0.814,-0.901],[-0.81,-0.933],[-0.814,-0.948],[-0.683,-1.143],[-0.645,-1.174],[-0.616,-1.185],[-0.525,-1.199],[-0.485,-1.21],[-0.467,-1.21],[-0.427,-1.221],[-0.409,-1.221],[-0.369,-1.232],[-0.318,-1.232],[-0.314,-1.235],[-0.27,-1.224],[-0.234,-1.203],[-0.207,-1.175],[-0.185,-1.128],[-0.189,-1.118],[-0.203,-1.103],[-0.203,-1.085],[-0.189,-1.067],[-0.189,-1.052],[-0.194,-1.047],[-0.216,-1.043],[-0.232,-1.02],[-0.229,-1.002],[-0.214,-0.98],[-0.223,-0.967],[-0.249,-0.96],[-0.258,-0.947],[-0.258,-0.922],[-0.243,-0.9],[-0.249,-0.891],[-0.278,-0.881],[-0.287,-0.864],[-0.287,-0.85],[-0.283,-0.839],[-0.272,-0.828],[-0.272,-0.817],[-0.278,-0.812],[-0.296,-0.808],[-0.312,-0.788],[-0.312,-0.767],[-0.298,-0.745],[-0.307,-0.732],[-0.318,-0.732],[-0.338,-0.719],[-0.345,-0.694],[-0.338,-0.676],[-0.327,-0.669],[-0.33,-0.658],[-0.336,-0.653],[-0.354,-0.649],[-0.37,-0.629],[-0.367,-0.6],[-0.345,-0.582],[-0.349,-0.567],[-0.345,-0.564],[-0.345,-0.524],[-0.338,-0.506],[-0.338,-0.491],[-0.301,-0.415],[-0.289,-0.41],[-0.26,-0.385],[-0.231,-0.374],[-0.172,-0.374],[-0.147,-0.381],[-0.122,-0.381],[-0.096,-0.388],[-0.045,-0.392],[-0.02,-0.399],[0.005,-0.399],[0.114,-0.417],[0.187,-0.418],[0.19,-0.414],[0.354,-0.403],[0.363,-0.398],[0.37,-0.383],[0.359,-0.329],[0.256,-0.233],[0.212,-0.208],[0.212,-0.201],[0.499,-0.201],[0.502,-0.197],[4.537,-0.197],[4.541,-0.2],[4.584,-0.204],[4.634,-0.222],[4.666,-0.24],[4.856,-0.24],[4.914,-0.211],[4.971,-0.197],[5.64,-0.197],[5.648,-0.19],[5.669,-0.19],[5.687,-0.201],[5.791,-0.201],[5.794,-0.205],[5.801,-0.201],[5.855,-0.201],[5.884,-0.187],[5.932,-0.135],[5.953,-0.088],[5.964,-0.049],[5.968,0.012],[5.964,0.016],[5.96,0.063],[5.932,0.131],[5.887,0.183],[5.858,0.197],[5.687,0.198],[5.669,0.183],[5.63,0.194],[5.619,0.201],[5.021,0.198],[5.018,0.202],[4.96,0.202],[4.924,0.209],[4.878,0.227],[4.853,0.245],[4.681,0.246],[4.659,0.242],[4.613,0.217],[4.58,0.206],[4.537,0.199],[0.005,0.201],[0,0.207],[0,0.344],[-0.009,0.342],[-0.02,0.35],[-0.049,0.346],[-0.093,0.353],[-0.249,0.354],[-0.243,0.359],[-0.247,0.366],[-0.292,0.412],[-0.301,0.406],[-0.309,0.431],[-0.33,0.464],[-0.349,0.518],[-0.352,0.569],[-0.356,0.573],[-0.352,0.584],[-0.378,0.609],[-0.374,0.638],[-0.354,0.654],[-0.339,0.654],[-0.334,0.667],[-0.334,0.674],[-0.349,0.689],[-0.349,0.714],[-0.336,0.73],[-0.314,0.734],[-0.309,0.739],[-0.309,0.75],[-0.32,0.761],[-0.323,0.772],[-0.32,0.793],[-0.31,0.806],[-0.285,0.813],[-0.28,0.822],[-0.28,0.83],[-0.294,0.848],[-0.294,0.869],[-0.278,0.889],[-0.254,0.895],[-0.254,0.913],[-0.269,0.931],[-0.269,0.949],[-0.256,0.965],[-0.231,0.972],[-0.225,0.985],[-0.24,1.003],[-0.243,1.025],[-0.227,1.048],[-0.201,1.052],[-0.196,1.065],[-0.214,1.094],[-0.214,1.104],[-0.201,1.124],[-0.191,1.132],[-0.176,1.131],[-0.171,1.141],[-0.171,1.148],[-0.189,1.17],[-0.189,1.188],[-0.172,1.207],[-0.154,1.211],[-0.149,1.227],[-0.152,1.253],[-0.171,1.296],[-0.209,1.338],[-0.241,1.356],[-0.267,1.363],[-0.314,1.363],[-0.55,1.317],[-0.59,1.295],[-0.607,1.279],[-0.817,0.957],[-0.825,0.943],[-0.817,0.932],[-0.821,0.892],[-0.83,0.894],[-0.837,0.887],[-0.865,0.881],[-0.868,0.871],[-0.857,0.852],[-0.865,0.834],[-0.881,0.818],[-0.907,0.815],[-0.912,0.809],[-0.901,0.777],[-0.908,0.773],[-0.921,0.753],[-0.932,0.746],[-0.95,0.746],[-0.959,0.737],[-0.948,0.708],[-0.956,0.701],[-0.956,0.693],[-0.979,0.677],[-0.999,0.675],[-1.003,0.664],[-0.996,0.65],[-0.996,0.632],[-1.007,0.617],[-1.007,0.61],[-1.041,0.608],[-1.061,0.578],[-1.072,0.545],[-1.076,0.494],[-1.079,0.491],[-1.079,0.418],[-1.072,0.407],[-1.076,0.386],[-1.072,0.382],[-1.072,0.331],[-1.076,0.328],[-1.069,0.317],[-1.076,0.31],[-1.072,0.306],[-1.076,0.302],[-1.076,0.219],[-1.072,0.215],[-1.072,0.19],[-1.079,0.165],[-1.076,0.157],[-1.079,0.139],[-1.076,0.121],[-1.079,0.117],[-1.076,0.114],[-1.076,0.041],[-1.079,0.038],[-1.076,0.027],[-1.079,0.02],[-1.072,0.012],[-1.076,0.005],[-1.072,0.002],[-1.072,-0.19],[-1.058,-0.227],[-1.076,-0.238],[-1.079,-0.245],[-1.076,-0.248]]},"features":{"plan":{"windows":[[[-0.796,0.751],[-0.792,0.784],[-0.77,0.827],[-0.719,0.899],[-0.65,1.011],[-0.625,1.044],[-0.625,1.051],[-0.614,1.062],[-0.599,1.091],[-0.588,1.102],[-0.541,1.178],[-0.499,1.212],[-0.379,1.237],[-0.343,1.237],[-0.307,1.219],[-0.294,1.202],[-0.287,1.181],[-0.29,1.134],[-0.309,1.09],[-0.309,1.079],[-0.316,1.068],[-0.32,1.047],[-0.33,1.025],[-0.352,0.953],[-0.359,0.942],[-0.363,0.92],[-0.37,0.909],[-0.414,0.772],[-0.443,0.714],[-0.459,0.698],[-0.499,0.68],[-0.528,0.68],[-0.572,0.691],[-0.627,0.691],[-0.63,0.687],[-0.641,0.691],[-0.699,0.677],[-0.721,0.677],[-0.747,0.684],[-0.761,0.691],[-0.781,0.711]],[[-0.785,-0.77],[-0.785,-0.741],[-0.774,-0.709],[-0.761,-0.696],[-0.736,-0.681],[-0.717,-0.678],[-0.685,-0.678],[-0.612,-0.692],[-0.554,-0.689],[-0.55,-0.685],[-0.485,-0.685],[-0.452,-0.7],[-0.432,-0.719],[-0.407,-0.777],[-0.32,-1.027],[-0.32,-1.056],[-0.33,-1.081],[-0.354,-1.101],[-0.376,-1.109],[-0.427,-1.105],[-0.467,-1.094],[-0.558,-1.08],[-0.594,-1.062],[-0.617,-1.038],[-0.752,-0.839],[-0.752,-0.832],[-0.77,-0.81]]],"catch_gap":[[[0,-0.264],[0,-0.206],[0.005,-0.2],[0.201,-0.2],[0.201,-0.204],[0.185,-0.21],[0.196,-0.257],[0.192,-0.285],[0.172,-0.302],[0.125,-0.305],[0.122,-0.309],[0.089,-0.309],[0.005,-0.291]]],"pins":[[[-0.608,0.444],[-0.597,0.444],[-0.597,0.433],[-0.608,0.433]],[[-0.6,-0.428],[-0.59,-0.428],[-0.59,-0.439],[-0.6,-0.439]]],"ports":[[[3.03,0.105],[3.03,0.127],[3.057,0.147],[3.114,0.15],[3.143,0.14],[3.152,0.131],[3.156,0.113],[3.148,0.095],[3.139,0.086],[3.134,0.087],[3.138,0.095],[3.13,0.098],[3.134,0.105],[3.129,0.107],[3.103,0.096],[3.057,0.1],[3.051,0.095],[3.049,0.082],[3.037,0.091]],[[3.03,-0.125],[3.033,-0.089],[3.046,-0.08],[3.044,-0.086],[3.053,-0.087],[3.053,-0.095],[3.078,-0.087],[3.125,-0.095],[3.139,-0.08],[3.156,-0.104],[3.156,-0.114],[3.152,-0.125],[3.139,-0.138],[3.118,-0.145],[3.067,-0.145],[3.046,-0.138]],[[3.479,0.105],[3.483,0.119],[3.479,0.127],[3.492,0.139],[3.517,0.15],[3.571,0.15],[3.582,0.146],[3.596,0.139],[3.605,0.123],[3.602,0.098],[3.589,0.081],[3.584,0.083],[3.587,0.101],[3.578,0.107],[3.546,0.096],[3.503,0.103],[3.505,0.094],[3.499,0.081]],[[3.479,-0.122],[3.479,-0.093],[3.487,-0.082],[3.496,-0.081],[3.494,-0.09],[3.499,-0.095],[3.517,-0.088],[3.557,-0.084],[3.56,-0.091],[3.571,-0.091],[3.582,-0.099],[3.584,-0.093],[3.576,-0.09],[3.593,-0.081],[3.605,-0.108],[3.602,-0.126],[3.578,-0.142],[3.56,-0.145],[3.524,-0.145],[3.488,-0.131]],[[3.929,0.104],[3.929,0.126],[3.945,0.142],[3.966,0.149],[4.024,0.149],[4.035,0.146],[4.051,0.133],[4.054,0.122],[4.051,0.101],[4.035,0.084],[4.029,0.086],[4.04,0.097],[4.028,0.106],[4.01,0.099],[3.959,0.099],[3.952,0.103],[3.954,0.097],[3.947,0.094],[3.95,0.086],[3.941,0.085]],[[3.929,-0.122],[3.932,-0.086],[3.938,-0.081],[3.948,-0.081],[3.954,-0.086],[3.945,-0.088],[3.945,-0.092],[4.01,-0.088],[4.031,-0.099],[4.036,-0.09],[4.029,-0.083],[4.042,-0.081],[4.054,-0.108],[4.051,-0.122],[4.035,-0.139],[4.01,-0.146],[3.974,-0.146],[3.938,-0.131]],[[4.378,0.104],[4.378,0.125],[4.404,0.145],[4.451,0.152],[4.483,0.145],[4.5,0.133],[4.503,0.111],[4.487,0.088],[4.489,0.097],[4.476,0.109],[4.451,0.098],[4.404,0.102],[4.395,0.097],[4.403,0.093],[4.394,0.084],[4.385,0.089]],[[4.374,-0.105],[4.381,-0.087],[4.39,-0.078],[4.395,-0.087],[4.39,-0.096],[4.426,-0.085],[4.444,-0.085],[4.476,-0.096],[4.487,-0.081],[4.5,-0.094],[4.503,-0.108],[4.5,-0.126],[4.473,-0.143],[4.412,-0.143],[4.394,-0.135],[4.378,-0.119]],[[4.826,0.1],[4.826,0.129],[4.835,0.137],[4.86,0.148],[4.903,0.152],[4.932,0.145],[4.944,0.136],[4.948,0.107],[4.932,0.087],[4.926,0.089],[4.93,0.1],[4.924,0.109],[4.892,0.098],[4.867,0.098],[4.838,0.105],[4.847,0.096],[4.84,0.093],[4.842,0.08]],[[4.826,-0.12],[4.829,-0.084],[4.835,-0.078],[4.84,-0.084],[4.837,-0.087],[4.838,-0.096],[4.881,-0.082],[4.917,-0.093],[4.932,-0.103],[4.933,-0.087],[4.942,-0.089],[4.948,-0.098],[4.948,-0.12],[4.935,-0.136],[4.921,-0.143],[4.863,-0.143],[4.838,-0.132]],[[5.27,0.121],[5.293,0.144],[5.326,0.151],[5.354,0.151],[5.372,0.148],[5.392,0.135],[5.395,0.11],[5.379,0.09],[5.374,0.106],[5.381,0.113],[5.376,0.115],[5.351,0.101],[5.333,0.097],[5.29,0.105],[5.29,0.083],[5.274,0.099]],[[5.27,-0.113],[5.277,-0.08],[5.286,-0.075],[5.299,-0.084],[5.293,-0.089],[5.347,-0.086],[5.376,-0.1],[5.381,-0.098],[5.377,-0.091],[5.383,-0.093],[5.381,-0.084],[5.386,-0.082],[5.395,-0.098],[5.392,-0.127],[5.361,-0.143],[5.318,-0.143],[5.286,-0.133]]]}},"placement":{"plan":{"plane":"xz","offset":{}}},"bounds":{"min":[-1.083,-0.4243,-1.235],"max":[5.895,0.2537,1.363]},"volume_in3":0.8866,"centroid":[0.6576,0.0313,0.0133],"shell":[1.4246,0.0251,0.0136],"area_in2":20.0228,"triangles":18462,"manifold":true,"slabs":[[-1.083,-0.149,-1.125,-0.695,0.254,1.144],[-0.695,-0.149,-1.235,0.08,0.257,1.363],[0.08,-0.149,-0.418,0.468,0.149,0.2],[0.468,-0.175,-0.24,5.507,0.149,0.246],[5.507,-0.424,-0.205,5.895,0.149,0.201]],"slots":["body","latches","pins"]},"radian-talon-safety-selector":{"part":"radian-talon-safety-selector","model":"radian-talon-safety-selector.glb","script":"radian_talon_safety_selector.py","inputs":{"radian-talon-safety-selector.dovetail_height":0.0689,"radian-talon-safety-selector.dovetail_width_base":0.206,"radian-talon-safety-selector.dovetail_width_top":0.2786,"radian-talon-safety-selector.groove_end_from_tip":0.096,"radian-talon-safety-selector.groove_first":0.08,"radian-talon-safety-selector.groove_pitch":0.0608,"radian-talon-safety-selector.groove_start":0.182,"radian-talon-safety-selector.groove_width":0.026,"radian-talon-safety-selector.grooves":3,"radian-talon-safety-selector.head_band_w":0.13,"radian-talon-safety-selector.head_d":0.4801,"radian-talon-safety-selector.head_groove_w":0.042,"radian-talon-safety-selector.head_rim_t":0.07,"radian-talon-safety-selector.head_t_shelf":0.2206,"radian-talon-safety-selector.head_t_top":0.1303,"radian-talon-safety-selector.lever_chamfer":0.024,"radian-talon-safety-selector.lever_reach":0.797,"radian-talon-safety-selector.lever_standoff":0.297,"radian-talon-safety-selector.lever_tip_t":0.2221,"radian-talon-safety-selector.lever_width":0.2569,"radian-talon-safety-selector.neck_fillet_r":0.07,"radian-talon-safety-selector.shaft_d":0.37225,"radian-talon-safety-selector.shaft_length":0.9613,"radian-talon-safety-selector.shelf_end":0.225,"radian-talon-safety-selector.shelf_point_length":0.09,"radian-talon-safety-selector.shelf_ramp":0.044,"radian-talon-safety-selector.shelf_start":0.0718,"radian-talon-safety-selector.short_lever_reach":0.609,"radian-talon-safety-selector.stud_hole_d":0.059,"radian-talon-safety-selector.tip_flank_angle":43,"radian-talon-safety-selector.tip_flat":0.036,"radian-talon-safety-selector.tip_rake":0.04,"std.ar15.lower_body_width":0.88,"std.ar15.selector_hole_d":0.376},"profiles":{},"bounds":{"min":[-0.797,-0.24,-0.7776],"max":[0.2401,0.24,0.7776]},"volume_in3":0.221,"centroid":[-0.1224,0,-0.03],"shell":[-0.124,0,-0.0287],"area_in2":3.9559,"triangles":9616,"manifold":true,"slabs":[[-0.797,-0.24,-0.778,0.24,0.24,-0.389],[-0.186,-0.186,-0.389,0.186,0.186,0.389],[-0.609,-0.24,0.389,0.24,0.24,0.778]],"slots":["levers","shaft","studs"]},"reptilia-aus-30mm-mount":{"part":"reptilia-aus-30mm-mount","model":"reptilia-aus-30mm-mount.glb","script":"reptilia_aus_30mm_mount.py","inputs":{"reptilia-aus-30mm-mount.base_plate_top_above_rail":0.335,"reptilia-aus-30mm-mount.base_top_above_rail":0.545,"reptilia-aus-30mm-mount.base_width":0.712,"reptilia-aus-30mm-mount.boss_face_length":0.88,"reptilia-aus-30mm-mount.boss_length":1.026,"reptilia-aus-30mm-mount.boss_outer_z":0.6,"reptilia-aus-30mm-mount.boss_top_above_rail":0.29,"reptilia-aus-30mm-mount.bridge_web_width":0.19,"reptilia-aus-30mm-mount.clamp_below_rail":0.25,"reptilia-aus-30mm-mount.clamp_bolt_axis_above_rail":0,"reptilia-aus-30mm-mount.clamp_bolt_end_d":0.166,"reptilia-aus-30mm-mount.clamp_bolt_groove_width":0.22,"reptilia-aus-30mm-mount.clamp_bolt_head_d":0.383,"reptilia-aus-30mm-mount.clamp_bolt_head_h":0.1,"reptilia-aus-30mm-mount.clamp_bolt_hex_af":0.15625,"reptilia-aus-30mm-mount.clamp_bolt_hex_depth":0.06,"reptilia-aus-30mm-mount.clamp_bolt_spacing":2.411,"reptilia-aus-30mm-mount.clamp_face_length":0.44,"reptilia-aus-30mm-mount.clamp_length":0.78,"reptilia-aus-30mm-mount.clamp_outer_z":0.64,"reptilia-aus-30mm-mount.clamp_top_above_rail":0.2,"reptilia-aus-30mm-mount.edge_break":0.006,"reptilia-aus-30mm-mount.jaw_below_rail":0.239,"reptilia-aus-30mm-mount.lug_depth":0.115,"reptilia-aus-30mm-mount.lug_length":0.2,"reptilia-aus-30mm-mount.lug_width":0.63,"reptilia-aus-30mm-mount.lug_x":1.214,"reptilia-aus-30mm-mount.optical_axis_above_rail":1.5354330708661417,"reptilia-aus-30mm-mount.pocket_depth":0.12,"reptilia-aus-30mm-mount.pocket_front_x":4.225,"reptilia-aus-30mm-mount.pocket_height":0.26,"reptilia-aus-30mm-mount.pocket_hole_d":0.115,"reptilia-aus-30mm-mount.pocket_hole_spacing":0.25,"reptilia-aus-30mm-mount.pocket_length":0.555,"reptilia-aus-30mm-mount.pocket_rear_x":0.705,"reptilia-aus-30mm-mount.pocket_recess_y":0.49,"reptilia-aus-30mm-mount.pocket_y":0.448,"reptilia-aus-30mm-mount.ring_bore":1.1811023622047243,"reptilia-aus-30mm-mount.ring_corner_chamfer":0.055,"reptilia-aus-30mm-mount.ring_flat_bottom_above_rail":1.473,"reptilia-aus-30mm-mount.ring_flat_top_above_rail":1.827,"reptilia-aus-30mm-mount.ring_front_x":4.264,"reptilia-aus-30mm-mount.ring_length":0.777,"reptilia-aus-30mm-mount.ring_neck_top_above_rail":0.887,"reptilia-aus-30mm-mount.ring_rear_x":0.642,"reptilia-aus-30mm-mount.ring_screw_bore_d":0.215,"reptilia-aus-30mm-mount.ring_screw_exit_d":0.185,"reptilia-aus-30mm-mount.ring_screw_head_below_top":0.37,"reptilia-aus-30mm-mount.ring_screw_head_d":0.15,"reptilia-aus-30mm-mount.ring_screw_spacing":0.489,"reptilia-aus-30mm-mount.ring_screw_z":0.735,"reptilia-aus-30mm-mount.ring_split_above_rail":1.645,"reptilia-aus-30mm-mount.ring_split_gap":0.01,"reptilia-aus-30mm-mount.ring_top_above_rail":2.222,"reptilia-aus-30mm-mount.ring_top_flat_width":0.8,"reptilia-aus-30mm-mount.ring_width":1.757,"reptilia-aus-30mm-mount.tail_width":0.83,"reptilia-aus-30mm-mount.under_pocket_depth":0.12,"reptilia-aus-30mm-mount.under_pocket_front_x0":2.871,"reptilia-aus-30mm-mount.under_pocket_front_x1":3.863,"reptilia-aus-30mm-mount.under_pocket_mid_x0":1.565,"reptilia-aus-30mm-mount.under_pocket_mid_x1":2.17,"reptilia-aus-30mm-mount.under_pocket_rear_x0":0.264,"reptilia-aus-30mm-mount.under_pocket_rear_x1":0.977,"reptilia-aus-30mm-mount.under_pocket_width":0.564,"reptilia-aus-30mm-mount.under_round_behind_bolt":0.288,"reptilia-aus-30mm-mount.under_round_d":0.267,"std.density.aluminium_7075":1.632,"std.density.steel":4.565,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{"side":[[-0.66,0.172],[-0.66,0.038],[-0.646,0.024],[-0.617,0.024],[-0.608,0.014],[-0.588,0.024],[-0.56,0.014],[-0.526,-0.01],[-0.507,-0.038],[-0.507,-0.191],[-0.455,-0.234],[-0.263,-0.234],[-0.254,-0.253],[0.158,-0.253],[0.167,-0.244],[0.492,-0.244],[0.497,-0.22],[0.526,-0.182],[0.526,-0.057],[0.54,-0.033],[0.578,-0.033],[0.588,-0.024],[0.617,-0.024],[0.626,-0.033],[0.636,-0.024],[0.684,-0.024],[0.703,-0.005],[1.095,-0.005],[1.105,0.005],[1.119,-0.01],[1.119,-0.067],[1.143,-0.1],[1.282,-0.105],[1.181,-0.11],[1.181,-0.12],[1.353,-0.12],[1.363,-0.005],[1.831,-0.005],[1.841,-0.014],[1.879,-0.024],[1.894,-0.048],[1.894,-0.163],[1.903,-0.172],[1.903,-0.191],[1.946,-0.225],[2.051,-0.225],[2.061,-0.244],[2.348,-0.244],[2.358,-0.234],[2.501,-0.234],[2.511,-0.225],[2.874,-0.225],[2.917,-0.182],[2.917,-0.057],[2.927,-0.038],[2.941,-0.024],[2.97,-0.024],[3.008,-0.005],[3.496,-0.005],[3.505,0.005],[3.572,0.005],[3.582,0.014],[3.639,0.014],[3.649,0.024],[3.706,0.024],[3.716,0.033],[3.831,0.043],[3.84,0.053],[3.898,0.053],[3.907,0.062],[3.965,0.062],[3.974,0.072],[4.031,0.072],[4.041,0.081],[4.108,0.081],[4.118,0.091],[4.184,0.091],[4.194,0.1],[4.242,0.1],[4.251,0.11],[4.338,0.11],[4.347,0.12],[4.376,0.12],[4.385,0.129],[4.404,0.129],[4.424,0.158],[4.443,0.158],[4.452,0.167],[4.471,0.167],[4.51,0.187],[4.548,0.225],[4.558,0.225],[4.591,0.268],[4.62,0.325],[4.62,0.363],[4.629,0.373],[4.62,0.756],[4.629,0.765],[4.629,0.957],[4.639,0.966],[4.648,1.31],[4.658,1.32],[4.658,1.597],[4.648,1.607],[4.648,1.645],[4.658,1.655],[4.658,1.865],[4.648,1.875],[4.648,1.942],[4.639,1.951],[4.639,1.999],[4.629,2.009],[4.629,2.066],[4.62,2.076],[4.62,2.123],[4.61,2.133],[4.61,2.181],[4.601,2.19],[4.601,2.21],[4.577,2.224],[3.878,2.224],[3.855,2.21],[3.845,2.19],[3.845,2.133],[3.855,2.123],[3.855,2.085],[3.835,2.076],[3.826,2.056],[3.826,1.99],[3.816,1.98],[3.816,1.808],[3.807,1.798],[3.807,1.291],[3.816,1.282],[3.816,1.062],[3.826,1.052],[3.826,0.928],[3.835,0.918],[3.835,0.756],[3.807,0.698],[3.745,0.627],[3.73,0.622],[3.725,0.607],[3.639,0.56],[3.611,0.56],[3.601,0.55],[3.544,0.55],[3.534,0.54],[1.363,0.54],[1.353,0.55],[1.315,0.55],[1.305,0.56],[1.286,0.56],[1.277,0.569],[1.238,0.579],[1.157,0.641],[1.157,0.65],[1.128,0.679],[1.109,0.717],[1.109,0.737],[1.1,0.746],[1.1,0.765],[1.109,0.775],[1.109,0.842],[1.119,0.851],[1.119,0.995],[1.128,1.004],[1.128,1.129],[1.138,1.138],[1.138,1.712],[1.128,1.722],[1.128,1.875],[1.119,1.884],[1.119,1.99],[1.109,1.999],[1.109,2.104],[1.1,2.114],[1.09,2.162],[1.071,2.181],[1.071,2.2],[1.057,2.214],[0.349,2.214],[0.315,2.181],[0.315,2.143],[0.306,2.133],[0.296,2.047],[0.287,2.037],[0.287,1.99],[0.277,1.98],[0.277,1.942],[0.268,1.932],[0.268,1.894],[0.258,1.884],[0.258,1.253],[0.268,1.243],[0.268,1.138],[0.277,1.129],[0.277,1.023],[0.287,1.014],[0.287,0.899],[0.296,0.89],[0.296,0.689],[0.287,0.679],[0.287,0.65],[0.248,0.583],[0.21,0.545],[0.21,0.536],[0.196,0.531],[0.148,0.483],[0.052,0.435],[0.033,0.435],[0.005,0.416],[-0.043,0.407],[-0.072,0.387],[-0.12,0.378],[-0.148,0.359],[-0.196,0.349],[-0.225,0.33],[-0.273,0.32],[-0.302,0.301],[-0.378,0.282],[-0.407,0.263],[-0.455,0.253],[-0.483,0.234],[-0.502,0.234],[-0.512,0.225],[-0.569,0.225],[-0.579,0.215],[-0.617,0.215],[-0.636,0.196],[-0.646,0.196]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{}}},"bounds":{"min":[-0.66,-0.25,-0.8785],"max":[4.6525,2.222,0.8785]},"axis_y":1.5354330708661417,"volume_in3":3.1951,"centroid":[2.0881,0.7462,-0.0104],"shell":[2.1094,0.8421,-0.0142],"area_in2":41.567,"triangles":23816,"manifold":true,"rail_seat":{"x":[-0.513,2.924],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-0.66,-0.25,-0.6,-0.281,0.315,0.537],[-0.281,-0.25,-0.6,0.099,0.458,0.668],[0.099,-0.25,-0.878,0.858,2.222,0.878],[0.858,-0.115,-0.878,1.237,2.222,0.878],[1.237,-0.115,-0.356,1.617,0.58,0.356],[1.617,-0.239,-0.6,1.996,0.54,0.356],[1.996,-0.25,-0.6,2.755,0.54,0.668],[2.755,-0.25,-0.6,3.135,0.54,0.452],[3.135,0,-0.356,3.514,0.54,0.356],[3.514,0.005,-0.878,4.273,2.222,0.878],[4.273,0.11,-0.878,4.653,2.222,0.878]],"slots":["body","hardware"]},"reptilia-dot-mount-193":{"part":"reptilia-dot-mount-193","model":"reptilia-dot-mount-193.glb","script":"reptilia_dot_mount.py","inputs":{"reptilia-dot-mount-193.base_chamfer":0.05,"reptilia-dot-mount-193.base_end_height":0.368,"reptilia-dot-mount-193.base_hole_d":0.12,"reptilia-dot-mount-193.base_hole_x":0.78,"reptilia-dot-mount-193.base_hole_z":0.4,"reptilia-dot-mount-193.bolt_above_foot":0.226,"reptilia-dot-mount-193.bolt_end_d":0.16,"reptilia-dot-mount-193.bolt_head_d":0.306,"reptilia-dot-mount-193.bolt_seat_d":0.403,"reptilia-dot-mount-193.bolt_seat_depth":0.02,"reptilia-dot-mount-193.bolt_slot_width":0.045,"reptilia-dot-mount-193.clamp_below_rail":0.223,"reptilia-dot-mount-193.clamp_length":0.6,"reptilia-dot-mount-193.clamp_proud":0.05,"reptilia-dot-mount-193.clamp_top_above_foot":0.33,"reptilia-dot-mount-193.deck_above_rail":1.38,"reptilia-dot-mount-193.deck_plate_thickness":0.132,"reptilia-dot-mount-193.deck_screw_d":0.17,"reptilia-dot-mount-193.deck_screw_x":0.62,"reptilia-dot-mount-193.deck_screw_z":0.31,"reptilia-dot-mount-193.deck_x":0,"reptilia-dot-mount-193.edge_break":0.006,"reptilia-dot-mount-193.flange_thickness":0.2,"reptilia-dot-mount-193.lip_top_above_rail":1.41,"reptilia-dot-mount-193.stem_width":0.551,"reptilia-dot-mount-193.web_thickness":0.1,"reptilia-dot-mount-193.width":1.24,"std.density.aluminium_7075":1.632,"std.density.steel":4.565,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{"side":[[-1.02,-1.401],[-1.02,-1.554],[-1.016,-1.599],[-1.005,-1.62],[-0.196,-1.627],[-0.024,-1.633],[0.196,-1.627],[1.002,-1.627],[1.016,-1.615],[1.02,-1.596],[1.02,-1.346],[1.013,-1.265],[0.989,-1.237],[0.67,-1.091],[0.586,-1.045],[0.539,-0.995],[0.516,-0.933],[0.513,-0.44],[0.529,-0.378],[0.552,-0.346],[0.576,-0.325],[0.846,-0.156],[0.875,-0.143],[0.93,-0.14],[0.946,-0.133],[0.987,-0.021],[0.987,-0.011],[0.976,-0.003],[0.771,0],[0.002,0],[-0.969,0],[-0.981,-0.008],[-0.981,-0.028],[-0.943,-0.13],[-0.882,-0.136],[-0.826,-0.159],[-0.576,-0.315],[-0.523,-0.372],[-0.507,-0.424],[-0.507,-0.914],[-0.513,-0.95],[-0.529,-0.989],[-0.583,-1.045],[-0.982,-1.234],[-1.013,-1.265]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"y":"lip_top_above_rail"}}},"bounds":{"min":[-1.02,-0.223,-0.62],"max":[1.02,1.38,0.71]},"volume_in3":1.2525,"centroid":[0.0026,0.4976,0.0048],"shell":[0.0016,0.5571,0.0091],"area_in2":18.6017,"triangles":9990,"manifold":true,"rail_seat":{"x":[-1.02,1.02],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-1.02,-0.216,-0.62,-0.34,1.38,0.62],[-0.34,-0.223,-0.62,0.34,1.38,0.71],[0.34,-0.217,-0.62,1.02,1.38,0.62]],"slots":["body","hardware"]},"reptilia-dot-mount-39mm":{"part":"reptilia-dot-mount-39mm","model":"reptilia-dot-mount-39mm.glb","script":"reptilia_dot_mount.py","inputs":{"reptilia-dot-mount-39mm.base_chamfer":0.05,"reptilia-dot-mount-39mm.base_end_height":0.37,"reptilia-dot-mount-39mm.base_hole_d":0.12,"reptilia-dot-mount-39mm.base_hole_x":0.78,"reptilia-dot-mount-39mm.base_hole_z":0.4,"reptilia-dot-mount-39mm.bolt_above_foot":0.23,"reptilia-dot-mount-39mm.bolt_end_d":0.16,"reptilia-dot-mount-39mm.bolt_head_d":0.3,"reptilia-dot-mount-39mm.bolt_seat_d":0.381,"reptilia-dot-mount-39mm.bolt_seat_depth":0.02,"reptilia-dot-mount-39mm.bolt_slot_width":0.045,"reptilia-dot-mount-39mm.clamp_below_rail":0.209,"reptilia-dot-mount-39mm.clamp_length":0.6,"reptilia-dot-mount-39mm.clamp_proud":0.05,"reptilia-dot-mount-39mm.clamp_top_above_foot":0.33,"reptilia-dot-mount-39mm.deck_above_rail":1.066,"reptilia-dot-mount-39mm.deck_plate_thickness":0.13,"reptilia-dot-mount-39mm.deck_screw_d":0.17,"reptilia-dot-mount-39mm.deck_screw_x":0.62,"reptilia-dot-mount-39mm.deck_screw_z":0.31,"reptilia-dot-mount-39mm.deck_x":0,"reptilia-dot-mount-39mm.edge_break":0.006,"reptilia-dot-mount-39mm.flange_thickness":0.2,"reptilia-dot-mount-39mm.lip_top_above_rail":1.096,"reptilia-dot-mount-39mm.stem_width":0.5511811023622047,"reptilia-dot-mount-39mm.web_thickness":0.1,"reptilia-dot-mount-39mm.width":1.2401574803149606,"std.density.aluminium_7075":1.632,"std.density.steel":4.565,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{"side":[[-1.028,-1.047],[-1.025,-1.195],[-1.016,-1.276],[-1.008,-1.29],[0.713,-1.305],[1.028,-1.303],[1.028,-0.93],[0.634,-0.741],[0.606,-0.716],[0.579,-0.677],[0.56,-0.616],[0.56,-0.454],[0.57,-0.414],[0.594,-0.372],[0.643,-0.331],[0.887,-0.181],[0.984,-0.175],[1.003,-0.161],[1.012,-0.137],[1.006,-0.131],[1.006,-0.038],[1.016,-0.017],[1.005,-0.006],[0.99,-0.003],[0.866,0],[0.002,0],[-0.957,0],[-0.964,-0.005],[-0.922,-0.131],[-0.912,-0.142],[-0.86,-0.157],[-0.833,-0.157],[-0.791,-0.172],[-0.547,-0.325],[-0.494,-0.369],[-0.473,-0.405],[-0.464,-0.441],[-0.464,-0.604],[-0.47,-0.64],[-0.488,-0.683],[-0.532,-0.729],[-0.559,-0.747],[-0.893,-0.901],[-1.005,-0.925],[-1.016,-0.948]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"y":"lip_top_above_rail"}}},"bounds":{"min":[-1.028,-0.209,-0.6201],"max":[1.028,1.066,0.7101]},"volume_in3":1.1949,"centroid":[0.0227,0.3754,0.0049],"shell":[0.0299,0.4355,0.0098],"area_in2":17.4408,"triangles":10224,"manifold":true,"rail_seat":{"x":[-1.028,1.028],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-1.028,-0.2,-0.62,-0.343,1.066,0.62],[-0.343,-0.206,-0.62,0.343,1.066,0.71],[0.343,-0.209,-0.62,1.028,1.066,0.62]],"slots":["body","hardware"]},"rise-lpk.selector":{"part":"rise-lpk","component":"selector","model":"rise-lpk.selector.glb","script":"brought_selectors.py","inputs":{"cmmg-safety-selector.hub_d":0.48,"cmmg-safety-selector.hub_t":0.05,"cmmg-safety-selector.lever_reach":0.81,"cmmg-safety-selector.lever_standoff":0.25,"cmmg-safety-selector.paddle_base_t":0.125,"cmmg-safety-selector.paddle_relief":0.015,"cmmg-safety-selector.paddle_relief_start":0.281,"cmmg-safety-selector.paddle_start":0.09,"cmmg-safety-selector.paddle_width":0.25,"cmmg-safety-selector.pointer_angle":60,"cmmg-safety-selector.pointer_fillet_r":0.09,"cmmg-safety-selector.pointer_reach":0.34,"cmmg-safety-selector.shaft_d":0.37225,"cmmg-safety-selector.shaft_end_chamfer":0.024,"cmmg-safety-selector.shaft_length":0.9375,"cmmg-safety-selector.step_1_height":0.17,"cmmg-safety-selector.step_1_inset":0.009,"cmmg-safety-selector.step_2_height":0.2,"cmmg-safety-selector.step_2_inset":0.025,"cmmg-safety-selector.step_3_height":0.22,"cmmg-safety-selector.step_3_inset":0.043,"cmmg-safety-selector.step_4_height":0.24,"cmmg-safety-selector.step_4_inset":0.075,"cmmg-safety-selector.step_5_inset":0.11,"std.ar15.lower_body_width":0.88,"std.ar15.selector_hole_d":0.376,"std.ar15.selector_x":0.803,"std.ar15.selector_y":-0.466},"profiles":{},"bounds":{"min":[-0.007,-0.7058,-0.25],"max":[1.143,-0.2262,0.9375]},"volume_in3":0.1423,"centroid":[0.703,-0.466,0.3065],"shell":[0.665,-0.466,0.2352],"area_in2":2.158,"triangles":6464,"manifold":true,"slabs":[[-0.007,-0.706,-0.25,1.143,-0.226,0.146],[0.617,-0.652,0.146,0.989,-0.28,0.938]],"slots":["controls"]},"rosco-bloodline-105-barrel":{"part":"rosco-bloodline-105-barrel","model":"rosco-bloodline-105-barrel.glb","script":"rosco_bloodline_105_barrel.py","inputs":{"rosco-bloodline-105-barrel.bore_d":0.219,"rosco-bloodline-105-barrel.crown_angle":11,"rosco-bloodline-105-barrel.extension_lug_bore_d":0.572,"rosco-bloodline-105-barrel.extension_lug_depth":0.214,"rosco-bloodline-105-barrel.extension_mouth_chamfer":0.045,"rosco-bloodline-105-barrel.extension_mouth_d":0.77,"rosco-bloodline-105-barrel.extension_od":0.994,"rosco-bloodline-105-barrel.extension_rear_x":-0.98,"rosco-bloodline-105-barrel.extension_recess_d":0.83,"rosco-bloodline-105-barrel.extension_recess_depth":0.595,"rosco-bloodline-105-barrel.flange_front_x":0.097,"rosco-bloodline-105-barrel.flange_od":1.167,"rosco-bloodline-105-barrel.gas_port_d":0.073,"rosco-bloodline-105-barrel.gas_port_x":7.208,"rosco-bloodline-105-barrel.index_pin_d":0.125,"rosco-bloodline-105-barrel.index_pin_top":0.582,"rosco-bloodline-105-barrel.index_pin_x":0.072,"rosco-bloodline-105-barrel.journal_front_x":8.859,"rosco-bloodline-105-barrel.journal_od":0.75,"rosco-bloodline-105-barrel.journal_rear_x":6.913,"rosco-bloodline-105-barrel.muzzle_od":0.729,"rosco-bloodline-105-barrel.outline_front_face":11.078,"rosco-bloodline-105-barrel.outline_rear_face":0.077,"rosco-bloodline-105-barrel.overall_length":11.001,"rosco-bloodline-105-barrel.ramp_rear_x":5.832,"rosco-bloodline-105-barrel.shoulder_x":9.41,"rosco-bloodline-105-barrel.taper_front_x":1.63,"rosco-bloodline-105-barrel.thread_major_d":0.4957,"rosco-bloodline-105-barrel.thread_minor_d":0.4551,"rosco-bloodline-105-barrel.thread_pitch":0.03571},"profiles":{"side":[[0.077,0.484],[0.078,-0.497],[1.017,-0.498],[1.03,-0.545],[1.06,-0.586],[1.184,-0.586],[1.193,-0.578],[1.198,-0.55],[1.209,-0.54],[1.222,-0.493],[1.884,-0.488],[1.912,-0.477],[1.939,-0.477],[2.026,-0.455],[2.113,-0.445],[2.118,-0.439],[2.146,-0.439],[2.173,-0.428],[2.2,-0.428],[2.26,-0.412],[2.315,-0.406],[2.32,-0.401],[2.347,-0.401],[2.435,-0.379],[2.456,-0.379],[2.462,-0.374],[2.489,-0.374],[2.522,-0.363],[2.549,-0.363],[2.555,-0.357],[2.637,-0.346],[2.642,-0.341],[2.697,-0.335],[2.702,-0.33],[6.902,-0.332],[6.907,-0.338],[6.986,-0.338],[6.992,-0.343],[7.092,-0.349],[7.098,-0.354],[7.12,-0.354],[7.193,-0.377],[7.21,-0.377],[7.306,-0.41],[7.356,-0.416],[7.362,-0.421],[7.396,-0.422],[7.401,-0.427],[7.975,-0.422],[7.981,-0.428],[8.006,-0.408],[8.02,-0.377],[8.066,-0.377],[8.071,-0.372],[9.909,-0.373],[9.915,-0.367],[9.972,-0.367],[9.977,-0.362],[10.486,-0.362],[10.523,-0.331],[10.535,-0.314],[10.56,-0.244],[10.824,-0.239],[10.83,-0.244],[10.933,-0.244],[10.938,-0.239],[10.984,-0.239],[10.99,-0.244],[11.078,-0.244],[11.078,0.246],[10.956,0.246],[10.95,0.251],[10.933,0.246],[10.921,0.251],[10.904,0.251],[10.898,0.246],[10.887,0.251],[10.87,0.251],[10.864,0.246],[10.852,0.251],[10.835,0.251],[10.83,0.246],[10.818,0.251],[10.795,0.251],[10.789,0.246],[10.778,0.251],[10.761,0.246],[10.703,0.246],[10.698,0.251],[10.692,0.246],[10.675,0.251],[10.658,0.251],[10.652,0.246],[10.64,0.251],[10.623,0.245],[10.572,0.245],[10.557,0.254],[10.54,0.304],[10.517,0.344],[10.503,0.358],[10.492,0.358],[10.474,0.369],[9.943,0.368],[9.937,0.374],[9.852,0.374],[9.846,0.379],[8.02,0.377],[8.006,0.407],[7.987,0.427],[7.351,0.426],[7.266,0.392],[7.25,0.392],[7.199,0.375],[7.177,0.375],[7.149,0.364],[7.126,0.364],[7.076,0.347],[7.014,0.342],[7.008,0.336],[6.924,0.336],[6.919,0.33],[6.913,0.336],[6.896,0.33],[6.807,0.33],[6.801,0.336],[6.784,0.336],[6.779,0.33],[6.728,0.33],[6.723,0.336],[6.717,0.33],[4.924,0.328],[4.919,0.333],[4.897,0.333],[4.891,0.328],[4.841,0.327],[4.836,0.333],[4.819,0.333],[4.814,0.327],[4.803,0.333],[2.915,0.33],[2.91,0.325],[2.762,0.325],[2.757,0.33],[2.691,0.33],[2.686,0.335],[2.62,0.341],[2.615,0.346],[2.593,0.346],[2.533,0.363],[2.506,0.363],[2.5,0.368],[2.478,0.368],[2.369,0.395],[2.309,0.401],[2.282,0.412],[2.222,0.417],[2.135,0.439],[2.042,0.45],[2.015,0.461],[1.988,0.461],[1.933,0.477],[1.868,0.482],[1.863,0.488],[1.797,0.488],[1.792,0.493],[1.651,0.493],[1.645,0.487],[1.64,0.493],[1.613,0.493],[1.607,0.487],[1.244,0.487],[1.214,0.495],[1.209,0.539],[1.179,0.574],[1.141,0.585],[1.087,0.585],[1.082,0.579],[1.076,0.585],[1.06,0.579],[1.025,0.505],[1.011,0.492],[0.984,0.492],[0.979,0.486],[0.827,0.491],[0.822,0.497],[0.509,0.496],[0.503,0.491],[0.094,0.495]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"x":"extension_rear_x"}}},"bounds":{"min":[-0.98,-0.5855,-0.5855],"max":[10.021,0.5855,0.5855]},"volume_in3":4.3536,"centroid":[4.0162,0.0001,0],"shell":[4.0245,0.0009,0],"area_in2":37.4036,"triangles":15058,"manifold":true,"slabs":[[-0.98,-0.494,-0.494,-0.194,0.494,0.494],[-0.194,-0.586,-0.586,0.199,0.586,0.586],[0.199,-0.489,-0.489,1.377,0.489,0.489],[1.377,-0.38,-0.38,1.77,0.38,0.38],[1.77,-0.364,-0.364,6.092,0.364,0.364],[6.092,-0.425,-0.425,7.271,0.425,0.425],[7.271,-0.375,-0.375,9.628,0.375,0.375],[9.628,-0.248,-0.248,10.021,0.248,0.248]],"slots":["barrel"]},"rosco-bloodline-115-barrel":{"part":"rosco-bloodline-115-barrel","model":"rosco-bloodline-115-barrel.glb","script":"rosco_bloodline_115_barrel.py","inputs":{"rosco-bloodline-115-barrel.bore_d":0.219,"rosco-bloodline-115-barrel.crown_angle":11,"rosco-bloodline-115-barrel.extension_lug_bore_d":0.572,"rosco-bloodline-115-barrel.extension_lug_depth":0.214,"rosco-bloodline-115-barrel.extension_mouth_chamfer":0.045,"rosco-bloodline-115-barrel.extension_mouth_d":0.77,"rosco-bloodline-115-barrel.extension_od":0.995,"rosco-bloodline-115-barrel.extension_rear_x":-0.972,"rosco-bloodline-115-barrel.extension_recess_d":0.83,"rosco-bloodline-115-barrel.extension_recess_depth":0.595,"rosco-bloodline-115-barrel.flange_front_x":0.095,"rosco-bloodline-115-barrel.flange_od":1.171,"rosco-bloodline-115-barrel.gas_port_d":0.073,"rosco-bloodline-115-barrel.gas_port_x":7.238,"rosco-bloodline-115-barrel.index_pin_d":0.125,"rosco-bloodline-115-barrel.index_pin_top":0.582,"rosco-bloodline-115-barrel.index_pin_x":0.072,"rosco-bloodline-115-barrel.journal_front_x":8.917,"rosco-bloodline-115-barrel.journal_od":0.75,"rosco-bloodline-115-barrel.journal_rear_x":6.943,"rosco-bloodline-115-barrel.muzzle_od":0.724,"rosco-bloodline-115-barrel.outline_front_face":12.115,"rosco-bloodline-115-barrel.outline_rear_face":0.114,"rosco-bloodline-115-barrel.overall_length":12.001,"rosco-bloodline-115-barrel.ramp_rear_x":5.933,"rosco-bloodline-115-barrel.shoulder_x":10.432,"rosco-bloodline-115-barrel.taper_front_x":1.632,"rosco-bloodline-115-barrel.thread_major_d":0.4957,"rosco-bloodline-115-barrel.thread_minor_d":0.4551,"rosco-bloodline-115-barrel.thread_pitch":0.03571},"profiles":{"side":[[0.114,0.498],[0.114,-0.493],[0.516,-0.494],[0.521,-0.5],[0.702,-0.5],[0.708,-0.494],[0.936,-0.495],[0.942,-0.501],[1.036,-0.501],[1.042,-0.578],[1.077,-0.578],[1.083,-0.584],[1.188,-0.584],[1.212,-0.572],[1.232,-0.552],[1.253,-0.49],[1.888,-0.491],[1.894,-0.485],[1.924,-0.485],[1.959,-0.473],[1.988,-0.473],[2.024,-0.461],[2.048,-0.461],[2.053,-0.456],[2.077,-0.456],[2.083,-0.45],[2.112,-0.45],[2.148,-0.438],[2.172,-0.438],[2.177,-0.432],[2.207,-0.432],[2.242,-0.42],[2.266,-0.42],[2.272,-0.414],[2.296,-0.414],[2.302,-0.408],[2.325,-0.408],[2.331,-0.403],[2.355,-0.403],[2.361,-0.397],[2.384,-0.397],[2.39,-0.391],[2.455,-0.385],[2.491,-0.373],[2.515,-0.373],[2.521,-0.367],[2.55,-0.367],[2.556,-0.361],[2.586,-0.361],[2.615,-0.349],[2.645,-0.349],[2.651,-0.344],[2.681,-0.344],[2.716,-0.332],[4.399,-0.334],[4.411,-0.328],[4.417,-0.334],[4.784,-0.335],[4.79,-0.329],[5.073,-0.329],[5.079,-0.335],[5.17,-0.335],[5.176,-0.329],[5.702,-0.33],[5.708,-0.336],[5.939,-0.336],[5.945,-0.33],[6.334,-0.331],[6.34,-0.337],[6.383,-0.337],[6.389,-0.331],[6.48,-0.331],[6.486,-0.337],[6.578,-0.337],[6.584,-0.331],[6.871,-0.331],[6.877,-0.325],[6.895,-0.325],[6.902,-0.331],[7.018,-0.332],[7.024,-0.338],[7.067,-0.338],[7.103,-0.35],[7.128,-0.35],[7.134,-0.356],[7.165,-0.356],[7.195,-0.368],[7.244,-0.374],[7.342,-0.411],[7.361,-0.411],[7.398,-0.429],[7.557,-0.423],[7.563,-0.429],[7.662,-0.429],[7.668,-0.423],[7.754,-0.424],[7.76,-0.43],[8.037,-0.43],[8.065,-0.409],[8.087,-0.376],[8.105,-0.369],[8.124,-0.37],[8.13,-0.376],[9.238,-0.377],[9.251,-0.371],[9.257,-0.377],[9.437,-0.378],[9.444,-0.371],[9.487,-0.372],[9.493,-0.378],[9.612,-0.378],[9.618,-0.372],[10.018,-0.372],[10.024,-0.366],[10.068,-0.366],[10.074,-0.36],[10.324,-0.361],[10.331,-0.367],[10.356,-0.367],[10.362,-0.361],[11.539,-0.362],[11.574,-0.341],[11.627,-0.246],[12.115,-0.246],[12.115,0.241],[12.071,0.24],[12.064,0.247],[11.659,0.24],[11.653,0.246],[11.627,0.246],[11.605,0.28],[11.599,0.305],[11.552,0.357],[11.4,0.357],[11.394,0.363],[10.08,0.361],[10.074,0.368],[10.018,0.367],[10.011,0.374],[9.593,0.373],[9.587,0.379],[9.574,0.373],[9.344,0.373],[9.338,0.379],[9.319,0.373],[8.698,0.372],[8.692,0.378],[8.321,0.378],[8.315,0.384],[8.309,0.378],[8.253,0.378],[8.247,0.372],[8.148,0.371],[8.142,0.377],[8.087,0.377],[8.043,0.426],[7.41,0.431],[7.275,0.382],[7.201,0.37],[7.195,0.364],[7.171,0.364],[7.14,0.352],[7.116,0.352],[7.085,0.34],[7.048,0.34],[7.042,0.334],[6.761,0.334],[6.755,0.327],[6.737,0.333],[6.486,0.333],[6.48,0.327],[6.474,0.333],[6.243,0.333],[6.237,0.327],[6.194,0.327],[6.188,0.333],[5.672,0.332],[5.666,0.326],[5.406,0.332],[5.4,0.326],[5.321,0.326],[5.315,0.332],[3.752,0.33],[3.746,0.336],[3.686,0.336],[3.68,0.33],[3.257,0.33],[3.251,0.336],[3.162,0.336],[3.156,0.33],[3.019,0.33],[3.013,0.336],[2.716,0.329],[2.71,0.335],[2.686,0.335],[2.651,0.347],[2.621,0.347],[2.615,0.353],[2.592,0.353],[2.586,0.359],[2.562,0.359],[2.526,0.371],[2.497,0.371],[2.491,0.377],[2.414,0.389],[2.408,0.394],[2.378,0.394],[2.343,0.406],[2.248,0.418],[2.219,0.43],[2.189,0.43],[2.16,0.442],[2.059,0.453],[2.053,0.459],[2.03,0.459],[2.024,0.465],[2,0.465],[1.994,0.471],[1.971,0.471],[1.935,0.483],[1.906,0.483],[1.9,0.489],[1.753,0.489],[1.747,0.495],[1.6,0.494],[1.594,0.488],[1.459,0.488],[1.453,0.494],[1.423,0.494],[1.417,0.488],[1.253,0.488],[1.244,0.497],[1.244,0.52],[1.227,0.562],[1.2,0.582],[1.118,0.582],[1.112,0.588],[1.106,0.582],[1.077,0.582],[1.065,0.576],[1.039,0.538],[1.033,0.508],[1.013,0.493],[0.942,0.493],[0.936,0.499]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"x":"extension_rear_x"}}},"bounds":{"min":[-0.972,-0.5849,-0.5849],"max":[11.029,0.5849,0.5849]},"volume_in3":4.7518,"centroid":[4.4986,0.0001,0],"shell":[4.5136,0.0008,0],"area_in2":40.4252,"triangles":16632,"manifold":true,"slabs":[[-0.972,-0.497,-0.497,-0.198,0.497,0.497],[-0.198,-0.585,-0.585,0.189,0.585,0.585],[0.189,-0.493,-0.493,1.351,0.493,0.493],[1.351,-0.387,-0.387,1.738,0.387,0.387],[1.738,-0.342,-0.342,5.996,0.342,0.342],[5.996,-0.43,-0.43,7.158,0.43,0.43],[7.158,-0.375,-0.375,10.642,0.375,0.375],[10.642,-0.248,-0.248,11.029,0.248,0.248]],"slots":["barrel"]},"rosco-bloodline-125-barrel":{"part":"rosco-bloodline-125-barrel","model":"rosco-bloodline-125-barrel.glb","script":"rosco_bloodline_125_barrel.py","inputs":{"rosco-bloodline-125-barrel.bore_d":0.219,"rosco-bloodline-125-barrel.crown_angle":11,"rosco-bloodline-125-barrel.extension_lug_bore_d":0.572,"rosco-bloodline-125-barrel.extension_lug_depth":0.214,"rosco-bloodline-125-barrel.extension_mouth_chamfer":0.045,"rosco-bloodline-125-barrel.extension_mouth_d":0.77,"rosco-bloodline-125-barrel.extension_od":0.999,"rosco-bloodline-125-barrel.extension_rear_x":-1.02,"rosco-bloodline-125-barrel.extension_recess_d":0.83,"rosco-bloodline-125-barrel.extension_recess_depth":0.595,"rosco-bloodline-125-barrel.flange_front_x":0.081,"rosco-bloodline-125-barrel.flange_od":1.186,"rosco-bloodline-125-barrel.gas_port_d":0.073,"rosco-bloodline-125-barrel.gas_port_x":7.227,"rosco-bloodline-125-barrel.index_pin_d":0.125,"rosco-bloodline-125-barrel.index_pin_top":0.594,"rosco-bloodline-125-barrel.index_pin_x":0.095,"rosco-bloodline-125-barrel.journal_front_x":8.928,"rosco-bloodline-125-barrel.journal_od":0.75,"rosco-bloodline-125-barrel.journal_rear_x":6.932,"rosco-bloodline-125-barrel.muzzle_od":0.72,"rosco-bloodline-125-barrel.outline_front_face":13.104,"rosco-bloodline-125-barrel.outline_rear_face":0.103,"rosco-bloodline-125-barrel.overall_length":13.001,"rosco-bloodline-125-barrel.ramp_rear_x":5.932,"rosco-bloodline-125-barrel.shoulder_x":11.389,"rosco-bloodline-125-barrel.taper_front_x":1.649,"rosco-bloodline-125-barrel.thread_major_d":0.4957,"rosco-bloodline-125-barrel.thread_minor_d":0.4551,"rosco-bloodline-125-barrel.thread_pitch":0.03571},"profiles":{"side":[[0.103,0.503],[0.103,-0.496],[0.108,-0.501],[0.917,-0.501],[0.923,-0.508],[0.949,-0.508],[0.956,-0.514],[1.055,-0.514],[1.058,-0.583],[1.107,-0.586],[1.114,-0.593],[1.212,-0.593],[1.238,-0.58],[1.268,-0.544],[1.275,-0.511],[1.291,-0.488],[1.298,-0.494],[1.941,-0.494],[1.948,-0.488],[1.981,-0.488],[1.987,-0.481],[2.013,-0.481],[2.02,-0.474],[2.053,-0.474],[2.086,-0.461],[2.118,-0.461],[2.125,-0.455],[2.151,-0.455],[2.158,-0.448],[2.184,-0.448],[2.191,-0.442],[2.217,-0.442],[2.223,-0.435],[2.25,-0.435],[2.256,-0.428],[2.289,-0.428],[2.296,-0.422],[2.322,-0.422],[2.329,-0.415],[2.361,-0.415],[2.368,-0.409],[2.394,-0.409],[2.401,-0.402],[2.427,-0.402],[2.434,-0.396],[2.46,-0.396],[2.466,-0.389],[2.493,-0.389],[2.499,-0.382],[2.525,-0.382],[2.532,-0.376],[2.565,-0.376],[2.571,-0.369],[2.598,-0.369],[2.604,-0.363],[2.637,-0.363],[2.67,-0.35],[2.696,-0.35],[2.703,-0.343],[2.729,-0.343],[2.735,-0.336],[2.768,-0.336],[2.775,-0.33],[3.739,-0.33],[3.746,-0.336],[3.851,-0.336],[3.857,-0.329],[3.864,-0.336],[3.871,-0.329],[3.877,-0.336],[3.884,-0.329],[3.89,-0.336],[3.897,-0.329],[3.903,-0.336],[3.91,-0.329],[3.917,-0.336],[3.923,-0.329],[3.93,-0.336],[3.936,-0.329],[3.943,-0.336],[3.949,-0.329],[4.054,-0.329],[4.061,-0.336],[4.526,-0.336],[4.533,-0.329],[4.579,-0.329],[4.585,-0.336],[6.571,-0.335],[6.578,-0.329],[6.938,-0.328],[6.945,-0.335],[7.056,-0.335],[7.063,-0.342],[7.095,-0.342],[7.102,-0.348],[7.148,-0.348],[7.154,-0.355],[7.194,-0.355],[7.2,-0.361],[7.259,-0.368],[7.37,-0.407],[7.41,-0.413],[7.449,-0.433],[8.071,-0.433],[8.11,-0.38],[8.13,-0.38],[8.136,-0.374],[8.3,-0.374],[8.307,-0.38],[9.981,-0.38],[9.988,-0.373],[10.289,-0.373],[10.295,-0.367],[10.916,-0.366],[10.923,-0.373],[10.969,-0.373],[10.975,-0.366],[12.484,-0.366],[12.491,-0.372],[12.497,-0.366],[12.524,-0.366],[12.537,-0.359],[12.56,-0.336],[12.573,-0.31],[12.579,-0.278],[12.595,-0.248],[12.609,-0.248],[12.615,-0.255],[12.628,-0.248],[12.641,-0.248],[12.648,-0.255],[12.661,-0.248],[12.68,-0.248],[12.687,-0.255],[12.7,-0.248],[12.713,-0.248],[12.72,-0.255],[12.733,-0.248],[12.746,-0.248],[12.752,-0.255],[12.765,-0.248],[12.778,-0.248],[12.785,-0.255],[12.798,-0.248],[12.817,-0.248],[12.824,-0.255],[12.831,-0.248],[12.85,-0.248],[12.857,-0.255],[12.863,-0.248],[12.883,-0.248],[12.889,-0.255],[12.902,-0.255],[12.909,-0.248],[12.922,-0.248],[12.928,-0.255],[12.935,-0.248],[12.955,-0.248],[12.961,-0.255],[12.968,-0.248],[12.981,-0.248],[12.987,-0.255],[13,-0.255],[13.007,-0.248],[13.013,-0.254],[13.104,-0.248],[13.104,0.217],[13.098,0.223],[13.085,0.23],[13.059,0.23],[13.053,0.236],[13.033,0.236],[13.026,0.23],[13.02,0.236],[12.798,0.236],[12.791,0.23],[12.785,0.236],[12.772,0.236],[12.765,0.23],[12.752,0.23],[12.739,0.236],[12.733,0.23],[12.72,0.23],[12.713,0.236],[12.706,0.23],[12.654,0.23],[12.648,0.236],[12.602,0.236],[12.586,0.252],[12.579,0.285],[12.553,0.331],[12.53,0.347],[12.504,0.347],[12.497,0.354],[12.452,0.347],[12.445,0.354],[10.086,0.36],[10.079,0.367],[9.667,0.366],[9.661,0.373],[8.516,0.373],[8.509,0.366],[8.464,0.366],[8.457,0.373],[8.149,0.373],[8.143,0.379],[8.136,0.373],[8.13,0.379],[8.11,0.379],[8.077,0.425],[7.442,0.425],[7.298,0.373],[7.279,0.373],[7.272,0.366],[7.239,0.366],[7.233,0.36],[7.207,0.36],[7.2,0.353],[7.174,0.353],[7.167,0.346],[7.102,0.34],[7.095,0.333],[6.997,0.333],[6.991,0.327],[6.945,0.327],[6.938,0.333],[2.768,0.333],[2.762,0.339],[2.729,0.339],[2.722,0.346],[2.696,0.346],[2.69,0.352],[2.663,0.352],[2.657,0.359],[2.63,0.359],[2.624,0.365],[2.591,0.365],[2.585,0.372],[2.558,0.372],[2.552,0.378],[2.525,0.378],[2.519,0.385],[2.493,0.385],[2.486,0.392],[2.46,0.392],[2.453,0.398],[2.42,0.398],[2.414,0.405],[2.355,0.411],[2.348,0.418],[2.315,0.418],[2.309,0.424],[2.283,0.424],[2.276,0.431],[2.25,0.431],[2.243,0.437],[2.171,0.444],[2.138,0.457],[2.072,0.464],[2.04,0.477],[2.007,0.477],[2,0.483],[1.974,0.483],[1.967,0.49],[1.941,0.49],[1.935,0.496],[1.587,0.496],[1.58,0.49],[1.383,0.49],[1.376,0.496],[1.311,0.496],[1.288,0.506],[1.268,0.552],[1.232,0.595],[1.12,0.595],[1.114,0.588],[1.101,0.588],[1.084,0.578],[1.051,0.519],[1.035,0.503],[0.949,0.503],[0.943,0.509],[0.122,0.509]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"x":"extension_rear_x"}}},"bounds":{"min":[-1.02,-0.5877,-0.5877],"max":[11.981,0.5877,0.5877]},"volume_in3":5.1464,"centroid":[4.9064,0.0001,0],"shell":[4.9391,0.0008,0],"area_in2":43.4581,"triangles":15236,"manifold":true,"slabs":[[-1.02,-0.5,-0.5,-0.232,0.5,0.5],[-0.232,-0.588,-0.588,0.162,0.588,0.588],[0.162,-0.492,-0.492,1.344,0.492,0.492],[1.344,-0.391,-0.391,1.738,0.391,0.391],[1.738,-0.358,-0.358,6.071,0.358,0.358],[6.071,-0.429,-0.429,7.253,0.429,0.429],[7.253,-0.375,-0.375,11.587,0.375,0.375],[11.587,-0.248,-0.248,11.981,0.248,0.248]],"slots":["barrel"]},"sb-tactical-sba3":{"part":"sb-tactical-sba3","model":"sb-tactical-sba3.glb","script":"sb_tactical_sba3.py","inputs":{"sb-tactical-sba3.bore_clearance":0.01,"sb-tactical-sba3.cavity_depth":6.219,"sb-tactical-sba3.cuff_window_width":1.05,"sb-tactical-sba3.endcap_inset":0.08,"sb-tactical-sba3.lever_thickness":0.08,"sb-tactical-sba3.lower_inset":0.12,"sb-tactical-sba3.pin_head_diameter":0.1,"sb-tactical-sba3.pocket_depth":0.1,"sb-tactical-sba3.qd_bore_diameter":0.4,"sb-tactical-sba3.qd_cup_diameter":0.55,"sb-tactical-sba3.relief_depth":0.03,"sb-tactical-sba3.strap_thickness":0.12,"sb-tactical-sba3.strap_width":1,"sb-tactical-sba3.tube_axis_below_top":0.95,"sb-tactical-sba3.width":1.8,"std.receiver_extension.milspec_od":1.148,"std.receiver_extension.rail_bottom_below_axis":0.874,"std.receiver_extension.rail_width":0.49},"profiles":{"side":[[0,-0.403],[0,-1.815],[0.017,-1.865],[0.042,-1.89],[0.075,-1.896],[0.117,-1.943],[0.1,-1.971],[0.1,-2.01],[0.111,-2.043],[0.117,-2.165],[0.128,-2.204],[0.156,-2.632],[0.178,-2.816],[0.239,-4.15],[0.256,-4.79],[0.25,-4.862],[0.261,-4.995],[0.261,-5.646],[0.267,-5.679],[0.295,-5.712],[0.356,-5.751],[0.356,-5.779],[0.403,-5.793],[1.443,-5.793],[1.468,-5.785],[1.479,-5.74],[1.543,-5.699],[1.562,-5.662],[1.562,-5.401],[1.59,-5.123],[1.59,-5.04],[1.757,-3.65],[1.857,-2.627],[1.876,-2.602],[1.993,-2.602],[2.09,-2.699],[2.088,-2.719],[2.099,-2.707],[2.282,-2.885],[2.327,-2.913],[3.405,-2.908],[3.477,-2.891],[3.555,-2.852],[3.614,-2.799],[3.647,-2.755],[3.675,-2.694],[3.669,-2.371],[3.683,-2.357],[5.195,-2.318],[5.29,-2.313],[5.362,-2.296],[5.479,-2.179],[5.496,-2.19],[5.509,-2.177],[5.498,-2.16],[5.621,-2.032],[5.632,-1.91],[5.651,-1.885],[5.996,-1.885],[6.032,-1.865],[6.054,-1.799],[6.049,-1.448],[6.06,-1.348],[6.343,-1.065],[6.338,-0.72],[6.31,-0.47],[6.305,-0.325],[6.293,-0.275],[6.274,-0.267],[5.646,-0.278],[1.743,-0.261],[1.465,0],[0.192,0],[0.156,-0.019],[0.145,-0.053],[0.133,-0.259],[0.058,-0.345],[0.025,-0.35],[0.011,-0.364]],"rear":[[-1.091,-1.094],[-1.081,-1.208],[-1.091,-1.283],[-1.07,-1.337],[-1.075,-1.37],[-1.037,-1.624],[-1.032,-1.797],[-1.01,-1.883],[-1.005,-1.975],[-0.978,-2.034],[-0.978,-2.072],[-0.967,-2.094],[-0.967,-2.175],[-0.951,-2.213],[-0.946,-2.272],[-0.935,-2.283],[-0.935,-2.332],[-0.924,-2.348],[-0.908,-2.45],[-0.913,-2.558],[-0.897,-2.591],[-0.902,-2.618],[-0.886,-2.645],[-0.875,-2.829],[-0.859,-2.872],[-0.859,-3.012],[-0.838,-3.056],[-0.832,-3.131],[-0.821,-3.147],[-0.816,-3.202],[-0.805,-3.212],[-0.8,-3.277],[-0.773,-3.326],[-0.751,-4.363],[-0.778,-4.417],[-0.783,-4.515],[-0.794,-4.536],[-0.794,-4.898],[-0.805,-4.909],[-0.783,-4.941],[-0.789,-5.006],[-0.773,-5.028],[-0.773,-5.066],[-0.762,-5.076],[-0.762,-5.125],[-0.74,-5.19],[-0.74,-5.217],[-0.686,-5.32],[-0.692,-5.33],[-0.67,-5.352],[-0.643,-5.406],[-0.611,-5.438],[-0.562,-5.514],[-0.446,-5.62],[-0.43,-5.62],[-0.392,-5.657],[-0.327,-5.684],[-0.246,-5.738],[-0.176,-5.755],[0.024,-5.76],[0.208,-5.744],[0.235,-5.738],[0.278,-5.711],[0.3,-5.728],[0.319,-5.714],[0.308,-5.703],[0.332,-5.679],[0.397,-5.647],[0.505,-5.555],[0.578,-5.482],[0.611,-5.428],[0.67,-5.357],[0.686,-5.309],[0.708,-5.282],[0.708,-5.255],[0.756,-5.147],[0.762,-5.087],[0.778,-5.071],[0.783,-5.049],[0.794,-4.552],[0.773,-4.417],[0.756,-4.347],[0.746,-4.336],[0.767,-3.753],[0.767,-3.347],[0.805,-3.283],[0.805,-3.261],[0.84,-3.226],[0.905,-3.274],[0.954,-3.274],[1,-3.234],[1.016,-3.191],[1.021,-3.104],[1.005,-2.958],[1.021,-2.931],[1.005,-2.818],[1.01,-2.607],[0.994,-2.569],[0.994,-2.386],[1.01,-2.223],[1.021,-2.207],[1.016,-2.186],[1.054,-2.007],[1.059,-1.937],[1.07,-1.921],[1.075,-1.829],[1.086,-1.807],[1.086,-1.759],[1.102,-1.705],[1.097,-1.683],[1.108,-1.667],[1.113,-1.58],[1.124,-1.548],[1.118,-1.537],[1.135,-1.467],[1.14,-1.364],[1.151,-1.348],[1.156,-1.089],[1.146,-1.029],[1.151,-0.986],[1.14,-0.975],[1.14,-0.905],[1.124,-0.829],[1.129,-0.786],[1.108,-0.732],[1.108,-0.684],[1.097,-0.667],[1.091,-0.608],[1.048,-0.494],[0.997,-0.411],[0.916,-0.357],[0.835,-0.346],[0.821,-0.332],[0.824,-0.324],[0.802,-0.335],[0.727,-0.286],[0.713,-0.273],[0.719,-0.23],[0.697,-0.208],[0.686,-0.17],[0.64,-0.124],[0.586,-0.097],[0.527,-0.081],[0.43,-0.086],[0.408,-0.113],[0.386,-0.119],[0.322,-0.173],[0.294,-0.184],[0.251,-0.184],[0.235,-0.173],[0.197,-0.178],[0.173,-0.154],[0.157,-0.041],[0.132,-0.011],[-0.003,0],[-0.014,0],[-0.138,-0.011],[-0.162,-0.068],[-0.173,-0.132],[-0.192,-0.151],[-0.365,-0.184],[-0.489,-0.249],[-0.554,-0.308],[-0.611,-0.343],[-0.621,-0.37],[-0.675,-0.419],[-0.762,-0.527],[-0.794,-0.554],[-0.886,-0.689],[-0.924,-0.727],[-0.935,-0.759],[-0.983,-0.824],[-1.048,-0.948],[-1.081,-1.035],[-1.081,-1.078]]},"features":{"side":{"through":[[[2.607,-2.493],[2.607,-2.416],[2.58,-2.349],[2.505,-2.279],[2.443,-2.263],[2.377,-2.263],[2.31,-2.291],[2.274,-2.332],[2.246,-2.41],[2.257,-2.493],[2.285,-2.543],[2.343,-2.596],[2.399,-2.619],[2.471,-2.619],[2.532,-2.596],[2.58,-2.555]],[[1.09,-0.147],[1.076,-0.133],[0.692,-0.133],[0.678,-0.147],[0.692,-0.161],[0.748,-0.161],[0.781,-0.172],[0.865,-0.161],[1.026,-0.167],[1.076,-0.161]]],"box":[[[6.413,0.064],[1.91,0.064],[1.91,-1.265],[6.413,-1.265]]],"lower":[[[6.413,-1.265],[1.91,-1.265],[1.91,-1.882],[6.413,-1.882]]],"cap":[[[1.91,0.064],[0.292,0.064],[0.292,-1.871],[1.91,-1.871]]],"endcap":[[[0.292,-0.27],[-0.092,-0.27],[-0.092,-1.882],[0.292,-1.882]]],"loop":[[[1.771,0.064],[0.075,0.064],[0.075,-0.225],[1.771,-0.225]]],"cuff":[[[1.993,-1.871],[-0.231,-1.871],[-0.231,-5.94],[1.993,-5.94]]],"strap":[[[1.404,-0.158],[0.297,-0.158],[0.297,-5.84],[1.404,-5.84]]],"keeper":[[[1.493,-3.572],[0.242,-3.572],[0.242,-4.011],[1.493,-4.011]]],"lever":[[[5.635,-1.765],[3.105,-1.576],[3.01,-1.587],[3.01,-2.254],[3.633,-2.31],[5.373,-2.288],[5.601,-2.004]]],"block":[[[3.689,-2.104],[1.815,-2.104],[1.815,-2.949],[3.689,-2.949]]],"notches":[[[5.818,-1.131],[5.106,-1.131],[5.106,-1.254],[5.818,-1.254]],[[3.394,-1.131],[2.705,-1.131],[2.705,-1.254],[3.394,-1.254]]],"groove":[[[6.052,-1.47],[1.926,-1.47],[1.926,-1.515],[6.052,-1.515]]],"pockets":[[[3.061,-2.282],[2.727,-2.282],[2.727,-2.894],[3.061,-2.894]],[[2.994,-1.882],[1.993,-1.882],[1.993,-2.127],[2.994,-2.127]]],"pins":[[[3.427,-1.871],[3.327,-1.871],[3.327,-1.971],[3.427,-1.971]],[[3.427,-2.677],[3.327,-2.677],[3.327,-2.777],[3.427,-2.777]]],"qd":[[[2.705,-2.138],[2.16,-2.138],[2.16,-2.682],[2.705,-2.682]]]},"rear":{"section":[[[-0.23,-0.014],[0.203,-0.014],[0.203,-0.251],[0.511,-0.251],[0.883,-0.975],[0.873,-1.861],[0.775,-2.099],[0.689,-3.18],[0.657,-4.261],[0.635,-5.071],[0.554,-5.422],[0.392,-5.584],[-0.014,-5.644],[-0.419,-5.584],[-0.581,-5.422],[-0.662,-5.071],[-0.684,-4.261],[-0.716,-3.18],[-0.802,-2.099],[-0.9,-1.861],[-0.91,-0.975],[-0.538,-0.251],[-0.23,-0.251]]],"opening":[[[-0.54,-3.337],[-0.54,-3.25],[-0.508,-3.158],[-0.475,-3.115],[-0.413,-3.064],[-0.327,-3.031],[-0.132,-3.01],[0.132,-3.01],[0.246,-3.02],[0.381,-3.048],[0.44,-3.08],[0.497,-3.137],[0.535,-3.202],[0.546,-3.25],[0.546,-3.412],[0.465,-3.537],[0.448,-3.628],[0.438,-3.639],[0.421,-3.704],[0.416,-3.796],[0.405,-3.828],[0.432,-4.044],[0.475,-4.152],[0.519,-4.212],[0.513,-4.271],[0.524,-4.293],[0.524,-4.428],[0.513,-4.839],[0.497,-4.887],[0.497,-4.925],[0.432,-5.066],[0.338,-5.171],[0.262,-5.22],[0.176,-5.257],[0.019,-5.279],[0.016,-5.303],[0.003,-5.317],[-0.024,-5.285],[-0.127,-5.274],[-0.24,-5.23],[-0.257,-5.209],[-0.278,-5.209],[-0.373,-5.12],[-0.411,-5.076],[-0.454,-4.99],[-0.486,-4.882],[-0.492,-4.817],[-0.492,-4.185],[-0.448,-4.131],[-0.443,-4.098],[-0.421,-4.066],[-0.421,-4.044],[-0.405,-4.012],[-0.389,-3.78],[-0.405,-3.645],[-0.416,-3.628],[-0.416,-3.574],[-0.448,-3.52],[-0.465,-3.472],[-0.508,-3.428],[-0.508,-3.347],[-0.527,-3.35]]],"split":[[[-0.046,-5.476],[0.019,-5.476],[0.019,-5.655],[-0.046,-5.655]]]}},"placement":{"side":{"plane":"xy","offset":{"y":"tube_axis_below_top"}},"rear":{"plane":"zy","offset":{"y":"tube_axis_below_top"}}},"bounds":{"min":[0,-4.8153,-1.0303],"max":[6.343,0.936,1.0033]},"volume_in3":18.7379,"centroid":[2.3758,-1.1144,-0.0168],"shell":[2.1969,-1.1869,-0.0091],"area_in2":136.6789,"triangles":9562,"manifold":true,"slabs":[[0,-4.815,-1.03,1.586,0.936,1.003],[1.586,-4.215,-0.91,1.982,0.837,0.883],[1.982,-1.963,-0.91,3.568,0.688,0.883],[3.568,-1.89,-0.91,3.964,0.681,0.883],[3.964,-1.4,-0.91,5.55,0.679,0.883],[5.55,-1.156,-0.91,5.947,0.677,0.883],[5.947,-0.935,-0.91,6.343,0.683,0.883]],"slots":["body","strap","hardware"]},"sb-tactical-sba4":{"part":"sb-tactical-sba4","model":"sb-tactical-sba4.glb","script":"sb_tactical_sba4.py","inputs":{"sb-tactical-sba4.block_width":0.78,"sb-tactical-sba4.bore_clearance":0.01,"sb-tactical-sba4.boss_width":0.34,"sb-tactical-sba4.cavity_depth":6.75,"sb-tactical-sba4.lever_pin_diameter":0.11,"sb-tactical-sba4.lever_slot_depth":0.04,"sb-tactical-sba4.loop_bar_thickness":0.067,"sb-tactical-sba4.qd_bore_diameter":0.29,"sb-tactical-sba4.qd_ring_diameter":0.42,"sb-tactical-sba4.rear_seam_depth":0.03,"sb-tactical-sba4.rear_seam_width":0.04,"sb-tactical-sba4.slot_depth":0.12,"sb-tactical-sba4.strap_thickness":0.05,"sb-tactical-sba4.strap_width":1,"sb-tactical-sba4.tube_axis_below_crest":0.981,"std.receiver_extension.milspec_od":1.148,"std.receiver_extension.rail_bottom_below_axis":0.874,"std.receiver_extension.rail_width":0.49},"profiles":{"side":[[0,-0.822],[0.006,-1.041],[0.028,-1.226],[0.039,-1.422],[0.09,-1.714],[0.09,-1.742],[0.079,-1.759],[0.101,-1.787],[0.152,-2.186],[0.163,-2.214],[0.185,-2.432],[0.253,-2.87],[0.275,-3.106],[0.297,-3.224],[0.325,-3.493],[0.342,-3.56],[0.359,-3.751],[0.46,-4.48],[0.466,-4.581],[0.455,-4.593],[0.471,-4.61],[0.483,-5.092],[0.494,-5.159],[0.477,-5.176],[0.499,-5.193],[0.525,-5.235],[0.76,-5.235],[0.772,-5.246],[0.788,-5.246],[0.808,-5.266],[0.797,-5.283],[0.811,-5.286],[0.819,-5.311],[0.839,-5.325],[1.664,-5.325],[1.742,-5.308],[1.787,-5.286],[1.801,-5.272],[1.801,-5.227],[1.815,-5.213],[2.101,-5.207],[2.129,-5.196],[2.194,-5.137],[2.362,-4.845],[2.404,-4.809],[2.432,-4.792],[2.444,-4.798],[2.489,-4.758],[2.758,-4.601],[2.988,-4.45],[3.016,-4.433],[3.027,-4.438],[3.05,-4.41],[3.173,-4.332],[3.852,-3.917],[3.874,-3.905],[3.88,-3.911],[3.908,-3.883],[4.009,-3.821],[4.099,-3.771],[4.105,-3.776],[4.121,-3.754],[4.25,-3.675],[4.323,-3.636],[4.329,-3.642],[4.374,-3.602],[4.525,-3.513],[4.548,-3.501],[4.553,-3.507],[4.61,-3.462],[4.823,-3.344],[4.935,-3.271],[4.957,-3.271],[4.991,-3.238],[5.317,-3.047],[5.468,-2.968],[5.603,-2.884],[5.625,-2.873],[5.631,-2.879],[5.676,-2.839],[5.698,-2.834],[6.091,-2.598],[6.164,-2.559],[6.169,-2.564],[6.293,-2.48],[6.357,-2.41],[6.397,-2.32],[6.402,-2.124],[6.422,-2.087],[6.764,-2.087],[6.837,-2.059],[6.913,-1.995],[6.958,-1.905],[6.963,-1.523],[6.98,-1.507],[6.963,-1.467],[6.963,-1.428],[6.98,-1.411],[6.969,-1.394],[6.969,-1.046],[6.98,-1.024],[6.98,-0.99],[6.93,-0.407],[6.91,-0.376],[6.888,-0.37],[6.848,-0.337],[2.55,-0.337],[2.348,-0.23],[2.118,-0.236],[2.093,-0.205],[2.087,-0.16],[2.062,-0.135],[1.961,-0.084],[1.866,-0.022],[1.81,0],[0.586,-0.006],[0.463,-0.067],[0.311,-0.163],[0.297,-0.227],[0.283,-0.241],[0.042,-0.241],[0.017,-0.278],[0.022,-0.295],[0.011,-0.39]],"rear":[[-1.121,-1.362],[-1.115,-1.448],[-1.096,-1.522],[-1.065,-1.584],[-1.053,-1.64],[-1.01,-1.726],[-1.004,-1.769],[-0.942,-1.924],[-0.936,-1.967],[-0.892,-2.072],[-0.855,-2.214],[-0.831,-2.27],[-0.8,-2.43],[-0.781,-2.467],[-0.757,-2.634],[-0.732,-2.714],[-0.701,-2.93],[-0.682,-2.998],[-0.676,-3.079],[-0.658,-3.146],[-0.59,-3.739],[-0.59,-3.758],[-0.614,-3.801],[-0.639,-3.881],[-0.639,-4.122],[-0.652,-4.227],[-0.652,-4.721],[-0.633,-4.851],[-0.614,-4.888],[-0.596,-4.968],[-0.528,-5.086],[-0.414,-5.206],[-0.358,-5.249],[-0.253,-5.299],[-0.093,-5.33],[0.093,-5.33],[0.272,-5.292],[0.358,-5.249],[0.414,-5.206],[0.497,-5.123],[0.559,-5.036],[0.602,-4.95],[0.608,-4.906],[0.633,-4.851],[0.652,-4.715],[0.652,-4.233],[0.639,-4.128],[0.639,-3.888],[0.633,-3.85],[0.59,-3.764],[0.59,-3.733],[0.658,-3.14],[0.676,-3.072],[0.682,-2.992],[0.701,-2.924],[0.732,-2.708],[0.757,-2.628],[0.781,-2.467],[0.8,-2.43],[0.824,-2.288],[0.849,-2.232],[0.899,-2.053],[0.929,-1.985],[0.948,-1.905],[0.997,-1.788],[1.016,-1.708],[1.096,-1.516],[1.115,-1.442],[1.121,-1.331],[1.109,-1.3],[1.102,-1.232],[1.071,-1.152],[0.985,-0.991],[0.936,-0.936],[0.818,-0.75],[0.757,-0.682],[0.633,-0.516],[0.513,-0.389],[0.463,-0.352],[0.389,-0.303],[0.296,-0.266],[0.185,-0.204],[0.17,-0.164],[0.151,-0.052],[0.124,-0.025],[0.093,0],[0,0],[-0.093,0],[-0.157,-0.065],[-0.182,-0.201],[-0.296,-0.266],[-0.389,-0.303],[-0.513,-0.389],[-0.639,-0.522],[-0.818,-0.75],[-0.936,-0.936],[-0.991,-0.997],[-1.065,-1.133],[-1.102,-1.232]]},"features":{"side":{"through":[[[5.089,-2.483],[5.075,-2.469],[4.548,-2.48],[4.534,-2.494],[4.528,-2.522],[4.528,-2.662],[4.503,-2.772],[4.458,-2.789],[4.368,-2.8],[4.026,-2.8],[3.931,-2.789],[3.88,-2.772],[3.866,-2.747],[3.866,-2.691],[3.855,-2.657],[3.855,-2.528],[3.849,-2.5],[3.835,-2.486],[3.403,-2.486],[3.083,-2.497],[3.016,-2.491],[2.466,-2.508],[2.264,-2.503],[2.233,-2.466],[2.222,-2.388],[2.228,-2.376],[2.216,-2.343],[2.205,-2.208],[2.2,-2.034],[2.186,-2.02],[2.124,-2.02],[2.087,-2.073],[2.087,-2.343],[2.127,-4.004],[2.132,-4.06],[2.155,-4.088],[2.219,-4.147],[2.281,-4.169],[2.298,-4.169],[2.32,-4.147],[2.348,-4.158],[2.365,-4.141],[2.376,-4.152],[2.399,-4.141],[2.522,-4.057],[2.59,-4.023],[2.668,-3.967],[2.691,-3.961],[3.252,-3.608],[3.347,-3.557],[3.588,-3.4],[3.639,-3.378],[3.947,-3.182],[3.998,-3.159],[4.206,-3.024],[4.963,-2.57],[4.985,-2.542],[4.997,-2.547],[5.019,-2.536]]],"slots":[[[6.13,-0.721],[4.868,-0.721],[4.868,-0.929],[6.13,-0.929]],[[4.66,-0.721],[3.398,-0.721],[3.398,-0.929],[4.66,-0.929]],[[3.173,-0.721],[1.922,-0.721],[1.922,-0.929],[3.173,-0.929]],[[6.13,-1.03],[4.868,-1.03],[4.868,-1.237],[6.13,-1.237]],[[4.66,-1.03],[3.398,-1.03],[3.398,-1.237],[4.66,-1.237]],[[3.173,-1.03],[1.922,-1.03],[1.922,-1.237],[3.173,-1.237]],[[6.13,-1.355],[4.868,-1.355],[4.868,-1.563],[6.13,-1.563]],[[4.66,-1.355],[3.398,-1.355],[3.398,-1.563],[4.66,-1.563]],[[3.173,-1.355],[1.922,-1.355],[1.922,-1.563],[3.173,-1.563]]],"qd":[[[6.826,-1.501],[6.405,-1.501],[6.405,-1.933],[6.826,-1.933]]],"qd_bore":[[[6.759,-1.574],[6.472,-1.574],[6.472,-1.86],[6.759,-1.86]]],"block":[[[5.401,-1.72],[2.202,-1.72],[2.202,-2.483],[5.401,-2.483]]],"boss":[[[4.514,-2.449],[3.852,-2.449],[3.852,-2.786],[4.514,-2.786]]],"strap":[[[1.737,0.031],[0.704,0.031],[0.704,-5.356],[1.737,-5.356]]],"loop":[[[2.062,0.031],[0.267,0.031],[0.267,-0.244],[2.062,-0.244]]],"housing":[[[7.028,0.031],[-0.042,0.031],[-0.042,-1.72],[7.028,-1.72]]],"nose":[[[7.028,0.031],[5.401,0.031],[5.401,-2.214],[7.028,-2.214]]],"lever_slots":[[[3.56,-1.922],[3.527,-1.933],[3.499,-1.961],[3.493,-1.995],[3.499,-2.028],[3.527,-2.056],[3.56,-2.068],[3.908,-2.068],[3.942,-2.056],[3.97,-2.028],[3.975,-1.995],[3.97,-1.961],[3.942,-1.933],[3.908,-1.922]],[[2.96,-2.051],[2.926,-2.068],[2.909,-2.101],[2.909,-2.135],[2.926,-2.169],[2.96,-2.186],[2.994,-2.186],[3.347,-2.085],[3.381,-2.068],[3.398,-2.034],[3.398,-2],[3.381,-1.967],[3.347,-1.95],[3.313,-1.95]],[[2.371,-2.202],[2.343,-2.225],[2.326,-2.253],[2.326,-2.292],[2.348,-2.32],[2.376,-2.337],[2.416,-2.337],[2.763,-2.225],[2.792,-2.202],[2.808,-2.174],[2.808,-2.135],[2.786,-2.107],[2.758,-2.09],[2.719,-2.09]]],"lever_pin":[[[4.267,-1.944],[4.155,-1.944],[4.155,-2.056],[4.267,-2.056]]],"pin_boss":[[[4.385,-1.776],[4.054,-1.776],[4.054,-2.157],[4.385,-2.157]]]},"rear":{"opening":[[[0.389,-2.313],[0.389,-2.504],[0.383,-2.554],[0.377,-2.603],[0.371,-2.652],[0.364,-2.702],[0.358,-2.751],[0.352,-2.801],[0.352,-2.85],[0.346,-2.899],[0.34,-2.949],[0.333,-2.998],[0.333,-3.048],[0.333,-3.097],[0.327,-3.146],[0.321,-3.196],[0.321,-3.245],[0.321,-3.295],[0.315,-3.344],[0.315,-3.393],[0.309,-3.443],[0.309,-3.492],[0.309,-3.542],[0.303,-3.591],[0.303,-3.64],[0.303,-3.69],[0.303,-3.739],[0.296,-3.789],[0.29,-3.838],[0.29,-3.888],[0.284,-3.937],[0.278,-3.986],[0.272,-4.036],[0.266,-4.085],[0.259,-4.135],[0.253,-4.184],[0.247,-4.233],[0.235,-4.283],[0.222,-4.332],[0.21,-4.382],[0.204,-4.431],[0.185,-4.48],[0.173,-4.53],[0.154,-4.579],[0.13,-4.629],[0.105,-4.678],[0.068,-4.727],[0.043,-4.777],[0.037,-4.826],[0.031,-4.876],[0.012,-4.925],[0,-4.968],[-0.012,-4.925],[-0.031,-4.876],[-0.037,-4.826],[-0.043,-4.777],[-0.068,-4.727],[-0.105,-4.678],[-0.13,-4.629],[-0.154,-4.579],[-0.173,-4.53],[-0.185,-4.48],[-0.204,-4.431],[-0.21,-4.382],[-0.222,-4.332],[-0.235,-4.283],[-0.247,-4.233],[-0.253,-4.184],[-0.259,-4.135],[-0.266,-4.085],[-0.272,-4.036],[-0.278,-3.986],[-0.284,-3.937],[-0.29,-3.888],[-0.29,-3.838],[-0.296,-3.789],[-0.303,-3.739],[-0.303,-3.69],[-0.303,-3.64],[-0.303,-3.591],[-0.309,-3.542],[-0.309,-3.492],[-0.309,-3.443],[-0.315,-3.393],[-0.315,-3.344],[-0.321,-3.295],[-0.321,-3.245],[-0.321,-3.196],[-0.327,-3.146],[-0.333,-3.097],[-0.333,-3.048],[-0.333,-2.998],[-0.34,-2.949],[-0.346,-2.899],[-0.352,-2.85],[-0.352,-2.801],[-0.358,-2.751],[-0.364,-2.702],[-0.371,-2.652],[-0.377,-2.603],[-0.383,-2.554],[-0.389,-2.504],[-0.389,-2.313]]],"tab":[[[-0.167,-0.003],[0.167,-0.003],[0.167,-0.293],[-0.167,-0.293]]],"boss":[[[-0.247,-2.393],[0.093,-2.393],[0.093,-2.64],[-0.247,-2.64]]],"panel":[[[0,-0.343],[0.136,-0.355],[0.29,-0.429],[0.414,-0.54],[0.537,-0.676],[0.661,-0.831],[0.772,-0.985],[0.865,-1.139],[0.92,-1.251],[0.939,-1.356],[0.92,-1.479],[0.865,-1.59],[0.797,-1.664],[0.364,-1.683],[0.364,-2.041],[0,-2.041],[-0.364,-2.041],[-0.364,-1.683],[-0.797,-1.664],[-0.865,-1.59],[-0.92,-1.479],[-0.939,-1.356],[-0.92,-1.251],[-0.865,-1.139],[-0.772,-0.985],[-0.661,-0.831],[-0.537,-0.676],[-0.414,-0.54],[-0.29,-0.429],[-0.136,-0.355]]],"medallion":[[[-0.476,-0.472],[0.463,-0.472],[0.463,-1.411],[-0.476,-1.411]]]}},"placement":{"side":{"plane":"xy","offset":{"y":"tube_axis_below_crest"}},"rear":{"plane":"zy","offset":{"y":"tube_axis_below_crest"}}},"bounds":{"min":[0,-4.353,-1.125],"max":[6.98,0.981,1.125]},"volume_in3":20.9087,"centroid":[2.9813,-1.1993,-0.0007],"shell":[2.9305,-1.1263,-0.0004],"area_in2":177.2797,"triangles":30612,"manifold":true,"slabs":[[0,-2.978,-1.121,0.388,0.866,1.121],[0.388,-4.353,-1.125,1.939,0.981,1.125],[1.939,-4.229,-1.121,2.327,0.911,1.121],[2.327,-3.925,-1.12,2.714,0.751,1.121],[2.714,-3.645,-1.121,3.102,0.644,1.121],[3.102,-3.396,-1.121,3.49,0.644,1.121],[3.49,-3.157,-1.12,3.878,0.644,1.121],[3.878,-2.93,-1.12,4.266,0.644,1.121],[4.266,-2.686,-1.121,4.653,0.644,1.121],[4.653,-2.457,-1.121,5.041,0.644,1.121],[5.041,-2.228,-1.12,5.429,0.644,1.121],[5.429,-2.007,-1.12,5.817,0.644,1.121],[5.817,-1.782,-1.121,6.204,0.644,1.121],[6.204,-1.559,-1.121,6.592,0.644,1.121],[6.592,-1.106,-1.121,6.98,0.644,1.121]],"slots":["body","strap","qd","hardware"]},"sb-tactical-sba5":{"part":"sb-tactical-sba5","model":"sb-tactical-sba5.glb","script":"sb_tactical_sba5.py","inputs":{"sb-tactical-sba5.cavity_depth":6,"sb-tactical-sba5.flap_wall":0.25,"sb-tactical-sba5.groove_depth":0.03,"sb-tactical-sba5.length":6.2,"sb-tactical-sba5.panel_depth":0.06,"sb-tactical-sba5.pin_diameter":0.077,"sb-tactical-sba5.qd_bore_diameter":0.37,"sb-tactical-sba5.split_width":0.02,"sb-tactical-sba5.strap_thickness":0.06,"sb-tactical-sba5.strap_width":1,"sb-tactical-sba5.tab_above_housing_top":0.297,"sb-tactical-sba5.tube_axis_below_top":0.957,"sb-tactical-sba5.width":2.1,"std.receiver_extension.milspec_od":1.148,"std.receiver_extension.rail_bottom_below_axis":0.874,"std.receiver_extension.rail_width":0.49},"profiles":{"side":[[0,-1.941],[0,-2.013],[0.041,-2.213],[0.072,-2.254],[0.051,-2.305],[0.051,-2.418],[0.092,-2.556],[0.41,-4.305],[0.569,-5.095],[0.597,-5.128],[0.644,-5.149],[0.741,-5.149],[0.808,-5.128],[1.756,-5.144],[1.785,-5.023],[1.803,-5.005],[1.821,-5.023],[1.821,-5.146],[1.844,-5.164],[1.869,-5.159],[1.918,-5.105],[2.887,-3.803],[3.579,-2.946],[3.585,-2.905],[3.651,-2.854],[3.692,-2.787],[3.71,-2.708],[3.736,-2.703],[3.915,-2.769],[3.946,-2.769],[3.972,-2.718],[3.985,-2.762],[4.074,-2.831],[4.131,-2.831],[5.31,-2.682],[5.767,-2.641],[5.849,-2.615],[5.964,-2.438],[6.082,-2.079],[6.072,-2.013],[6,-1.951],[6.01,-1.941],[6,-1.931],[6.082,-1.7],[6.179,-1.556],[6.2,-0.977],[6.2,-0.751],[6.174,-0.515],[6.123,-0.351],[6.069,-0.308],[5.997,-0.292],[5.074,-0.287],[2.105,-0.287],[2.036,-0.228],[2.026,-0.141],[1.995,-0.059],[1.931,-0.01],[1.859,0],[1.49,-0.015],[0.756,-0.01],[0.679,-0.021],[0.626,-0.059],[0.456,-0.305],[0.282,-0.5],[0.133,-0.777]],"rear":[[-1.127,-1.687],[-1.117,-1.697],[-1.112,-1.768],[-1.097,-1.793],[-1.102,-1.844],[-1.092,-1.894],[-1.097,-1.914],[-1.082,-1.97],[-1.092,-1.985],[-1.077,-2.005],[-1.077,-2.111],[-1.062,-2.126],[-1.047,-2.267],[-1.011,-2.393],[-1.021,-2.429],[-1.001,-2.439],[-0.996,-2.499],[-0.986,-2.514],[-0.986,-2.565],[-1.001,-2.59],[-0.981,-2.62],[-0.976,-2.686],[-0.956,-2.767],[-0.951,-2.827],[-0.961,-2.842],[-0.946,-2.857],[-0.956,-2.868],[-0.941,-2.883],[-0.91,-2.999],[-0.91,-3.039],[-0.9,-3.049],[-0.9,-3.079],[-0.885,-3.115],[-0.885,-3.135],[-0.9,-3.155],[-0.888,-3.147],[-0.875,-3.16],[-0.87,-3.221],[-0.855,-3.251],[-0.86,-3.266],[-0.85,-3.276],[-0.84,-3.392],[-0.85,-3.402],[-0.83,-3.432],[-0.81,-3.523],[-0.81,-3.569],[-0.789,-3.644],[-0.769,-3.821],[-0.699,-4.048],[-0.699,-4.088],[-0.653,-4.3],[-0.638,-4.461],[-0.618,-4.532],[-0.608,-4.633],[-0.618,-4.648],[-0.598,-4.658],[-0.572,-4.789],[-0.507,-4.91],[-0.482,-5.052],[-0.434,-5.12],[-0.368,-5.15],[-0.045,-5.155],[-0.035,-5.145],[-0.015,-5.145],[0.293,-5.16],[0.348,-5.145],[0.406,-5.087],[0.441,-4.961],[0.507,-4.865],[0.512,-4.835],[0.537,-4.799],[0.532,-4.779],[0.547,-4.764],[0.542,-4.744],[0.572,-4.577],[0.593,-4.567],[0.578,-4.542],[0.593,-4.451],[0.618,-4.386],[0.613,-4.355],[0.643,-4.25],[0.653,-4.174],[0.668,-4.159],[0.663,-4.129],[0.689,-4.043],[0.739,-3.765],[0.754,-3.705],[0.779,-3.68],[0.769,-3.67],[0.769,-3.649],[0.779,-3.614],[0.794,-3.599],[0.784,-3.584],[0.794,-3.538],[0.812,-3.516],[0.82,-3.518],[0.81,-3.488],[0.83,-3.478],[0.815,-3.448],[0.83,-3.432],[0.82,-3.422],[0.835,-3.367],[0.83,-3.357],[0.845,-3.327],[0.85,-3.286],[0.865,-3.271],[0.86,-3.256],[0.875,-3.241],[0.865,-3.231],[0.895,-3.16],[0.895,-3.125],[0.915,-3.1],[0.905,-3.084],[0.905,-3.059],[1.016,-2.615],[1.062,-2.388],[1.077,-2.298],[1.072,-2.192],[1.087,-2.146],[1.112,-1.985],[1.117,-1.793],[1.127,-1.783],[1.117,-1.748],[1.127,-1.607],[1.112,-1.49],[1.087,-1.425],[1.087,-1.264],[1.072,-1.183],[1.067,-1.077],[1.031,-1.006],[1.021,-0.926],[0.936,-0.729],[0.941,-0.724],[0.83,-0.547],[0.784,-0.507],[0.787,-0.499],[0.696,-0.424],[0.615,-0.378],[0.58,-0.363],[0.575,-0.368],[0.545,-0.338],[0.54,-0.343],[0.474,-0.303],[0.421,-0.25],[0.416,-0.134],[0.406,-0.098],[0.386,-0.063],[0.348,-0.03],[0.288,-0.015],[0.151,-0.01],[0.121,0],[0.003,-0.003],[-0.025,0],[-0.212,-0.015],[-0.247,-0.03],[-0.29,-0.083],[-0.295,-0.209],[-0.305,-0.24],[-0.368,-0.298],[-0.404,-0.313],[-0.464,-0.358],[-0.532,-0.431],[-0.562,-0.482],[-0.764,-0.936],[-0.86,-1.122],[-0.86,-1.137],[-0.991,-1.395],[-1.021,-1.521],[-1.034,-1.533],[-1.059,-1.533],[-1.092,-1.571],[-1.102,-1.647]]},"features":{"side":{"through":[[[3.313,-2.259],[3.295,-2.2],[2.126,-2.205],[2.079,-2.21],[2.056,-2.233],[2.041,-2.413],[2.041,-3.741],[2.067,-3.813],[2.11,-3.856],[2.167,-3.877],[2.259,-3.867],[2.313,-3.823],[3.287,-2.51]]],"strap":[[[1.695,-0.074],[0.71,-0.074],[0.71,-5.151],[1.695,-5.151]]],"tab":[[[2.079,0.018],[0.592,0.018],[0.592,-0.3],[2.079,-0.3]]],"cuff":[[[2.038,-2.295],[-0.049,-2.295],[-0.049,-5.187],[2.038,-5.187]]],"seam":[[[1.951,-2.279],[0.003,-2.279],[0.003,-2.31],[1.951,-2.31]]],"strut":[[[3.746,-2.238],[2.038,-2.238],[2.038,-5.187],[3.746,-5.187]]],"lever":[[[6.218,-1.972],[4.915,-1.972],[4.874,-1.674],[3.736,-1.674],[3.736,-2.854],[6.218,-2.854]]],"pins":[[[3.951,-1.854],[3.874,-1.854],[3.874,-1.931],[3.951,-1.931]],[[3.946,-2.546],[3.869,-2.546],[3.869,-2.623],[3.946,-2.623]]],"qdpanel":[[[2.7,-1.479],[1.951,-1.479],[1.951,-2.187],[2.7,-2.187]]],"blank":[[[3.362,-1.479],[2.721,-1.479],[2.721,-2.208],[3.362,-2.208]]],"qd":[[[2.459,-1.679],[2.09,-1.679],[2.09,-2.049],[2.459,-2.049]]],"chevron":[[[6.141,-0.874],[4.623,-1.387],[6.141,-1.572]]]},"rear":{"channel":[[[-0.416,-2.883],[-0.416,-2.842],[-0.388,-2.82],[-0.05,-2.835],[0.288,-2.825],[0.328,-2.835],[0.356,-2.868],[0.351,-2.994],[0.275,-3.569],[0.26,-3.649],[0.23,-3.72],[0.159,-4.234],[0.149,-4.26],[0.106,-4.308],[0.086,-4.318],[0.076,-4.308],[0.061,-4.323],[-0.146,-4.318],[-0.177,-4.308],[-0.204,-4.28],[-0.23,-4.234],[-0.28,-3.816],[-0.305,-3.72],[-0.34,-3.503],[-0.366,-3.281],[-0.366,-3.256],[-0.356,-3.241],[-0.376,-3.216],[-0.386,-3.074]]],"cap":[[[-1.17,-0.29],[1.15,-0.29],[1.15,-2.131],[-1.17,-2.131]]],"strap":[[[-1.12,-1.274],[-0.958,-1.274],[-0.938,-2.837],[-0.787,-3.947],[-0.636,-4.653],[-0.666,-4.704],[-0.837,-3.947],[-0.999,-2.837],[-1.12,-1.929]],[[0.928,-0.366],[1.09,-0.416],[1.13,-1.274],[1.039,-1.274]]]}},"placement":{"side":{"plane":"xy","offset":{"y":"tube_axis_below_top"}},"rear":{"plane":"zy","offset":{"y":"tube_axis_below_top"}}},"bounds":{"min":[0,-4.2629,-1.11],"max":[6.2,0.9569,1.11]},"volume_in3":21.9092,"centroid":[2.805,-1.2139,0],"shell":[2.4162,-1.2043,0],"area_in2":149.5737,"triangles":14860,"manifold":true,"slabs":[[0,-3.224,-1.05,0.387,0.575,1.05],[0.387,-4.263,-1.11,1.937,0.957,1.11],[1.937,-4.122,-1.05,2.325,0.942,1.05],[2.325,-3.601,-1.05,2.712,0.67,1.05],[2.712,-3.08,-1.05,3.1,0.67,1.05],[3.1,-2.582,-1.05,3.487,0.67,1.05],[3.487,-2.102,-1.05,3.875,0.67,1.05],[3.875,-1.874,-1.05,4.65,0.67,1.05],[4.65,-1.808,-1.05,5.425,0.67,1.05],[5.425,-1.715,-1.05,6.2,0.668,1.05]],"slots":["body","strap","qd","hardware"]},"sb-tactical-sbpdw-brace":{"part":"sb-tactical-sbpdw-brace","model":"sb-tactical-sbpdw-brace.glb","script":"sb_tactical_sbpdw_brace.py","inputs":{"sb-tactical-sbpdw-brace.body_width":1.45,"sb-tactical-sbpdw-brace.bore_d":1.166,"sb-tactical-sbpdw-brace.butt_behind_pin_pos1":8.365,"sb-tactical-sbpdw-brace.rod_below_axis":0.78,"sb-tactical-sbpdw-brace.rod_d":0.334,"sb-tactical-sbpdw-brace.rod_enters_strut_ahead_of_butt":2.03,"sb-tactical-sbpdw-brace.rod_front_ahead_of_butt":8.63,"sb-tactical-sbpdw-brace.rod_spacing":1.175,"sb-tactical-sbpdw-brace.strap_centre_ahead_of_butt":0.72,"sb-tactical-sbpdw-brace.strap_thickness":0.06,"sb-tactical-sbpdw-brace.strap_width":1,"sb-tactical-sbpdw-receiver-extension.tube_front_behind_pin":0.669,"sb-tactical-sbpdw-receiver-extension.tube_length":6.992},"profiles":{"side":[[-0.003,-0.718],[-0.003,-1.138],[0.145,-3.514],[0.186,-3.75],[0.242,-3.824],[0.361,-3.901],[0.378,-3.942],[0.479,-3.954],[1.383,-3.96],[1.415,-3.945],[1.421,-3.904],[1.442,-3.883],[1.513,-3.871],[1.625,-3.8],[1.676,-3.715],[1.711,-3.496],[1.723,-3.254],[1.817,-2.651],[1.918,-1.853],[2.018,-1.155],[2.042,-1.114],[2.042,-0.588],[2.057,-0.573],[3.227,-0.573],[3.23,0.57],[3.206,0.683],[3.132,0.745],[1.755,0.751],[1.489,0.999],[1.306,1.005],[1.274,1.025],[1.259,1.07],[1.229,1.076],[0.922,1.082],[0.626,1.064],[0.567,1.076],[0.55,1.064],[0.313,1.07],[0.301,1.058],[0.219,1.058],[0.204,1.031],[0.186,0.836],[0.103,0.712],[0.056,0.464]],"rear":[[-1.125,-1.374],[-1.096,-1.655],[-0.96,-2.281],[-0.742,-3.167],[-0.598,-3.6],[-0.517,-3.725],[-0.427,-3.808],[-0.315,-3.874],[-0.15,-3.907],[0.019,-3.894],[0.076,-3.907],[0.2,-3.878],[0.571,-3.853],[0.622,-3.806],[0.639,-3.769],[0.63,-3.624],[0.67,-3.536],[0.696,-3.674],[0.725,-3.731],[0.769,-3.758],[0.818,-3.742],[0.837,-3.715],[0.841,-3.641],[0.799,-3.414],[0.853,-3.212],[0.898,-2.693],[1.01,-1.972],[1.117,-1.498],[1.125,-1.304],[1.088,-1.057],[1.026,-0.847],[0.841,-0.517],[0.754,-0.332],[0.668,-0.2],[0.659,-0.163],[0.548,-0.01],[0.538,0],[-0.002,0],[-0.558,0],[-0.591,-0.066],[-0.678,-0.091],[-0.713,-0.134],[-0.729,-0.233],[-0.804,-0.348],[-0.828,-0.472],[-1.051,-0.921],[-1.113,-1.152]]},"features":{"side":{"window":[[[1.472,0.145],[2.772,0.145],[2.819,0.086],[2.837,-0.074],[2.801,-0.192],[2.742,-0.251],[2.476,-0.352],[2.122,-0.488],[1.826,-0.553],[1.619,-0.564],[1.543,-0.529],[1.483,-0.428],[1.466,0.015]]],"cuff":[[[-0.183,1.256],[1.383,1.256],[1.383,-4.122],[-0.183,-4.122]]],"top":[[[1.383,1.256],[3.304,1.256],[3.304,-0.576],[1.383,-0.576]]]},"rear":{"opening":[[[-0.639,-1.762],[-0.579,-1.698],[-0.521,-1.673],[-0.183,-1.611],[0.208,-1.611],[0.571,-1.677],[0.655,-1.741],[0.589,-2.124],[0.523,-2.26],[0.49,-2.384],[0.482,-2.705],[0.375,-3.072],[0.301,-3.212],[0.216,-3.288],[0.072,-3.35],[0.021,-3.398],[-0.01,-3.478],[-0.045,-3.394],[-0.089,-3.354],[-0.183,-3.321],[-0.282,-3.251],[-0.326,-3.204],[-0.375,-3.109],[-0.474,-2.763],[-0.462,-2.438],[-0.482,-2.289],[-0.519,-2.178],[-0.589,-2.075]]]}},"placement":{"side":{"plane":"xy","offset":{}},"rear":{"plane":"zy","offset":{}}},"bounds":{"min":[-0.003,-3.96,-1.125],"max":[8.63,1.082,1.125]},"volume_in3":12.6621,"centroid":[1.4328,-1.0881,0.0141],"shell":[1.6696,-1.141,0.0221],"area_in2":104.2076,"triangles":8778,"manifold":true,"slabs":[[-0.003,-3.96,-1.125,1.567,1.082,1.125],[1.567,-3.837,-1.125,1.959,0.927,1.125],[1.959,-1.567,-1.125,2.351,0.75,1.125],[2.351,-0.947,-0.754,3.529,0.748,0.754],[3.529,-0.947,-0.754,8.63,-0.613,0.754]],"slots":["body","strap","rods"]},"sb-tactical-sbpdw-receiver-extension":{"part":"sb-tactical-sbpdw-receiver-extension","model":"sb-tactical-sbpdw-receiver-extension.glb","script":"sb_tactical_sbpdw_receiver_extension.py","inputs":{"sb-tactical-sbpdw-brace.rod_below_axis":0.78,"sb-tactical-sbpdw-brace.rod_d":0.334,"sb-tactical-sbpdw-brace.rod_spacing":1.175,"sb-tactical-sbpdw-receiver-extension.bore_d":1,"sb-tactical-sbpdw-receiver-extension.ear_wall":0.09,"sb-tactical-sbpdw-receiver-extension.housing_bore":1.1813,"sb-tactical-sbpdw-receiver-extension.housing_bottom_below_axis":1.26,"sb-tactical-sbpdw-receiver-extension.housing_front_behind_pin":1.125,"sb-tactical-sbpdw-receiver-extension.housing_length":2.02,"sb-tactical-sbpdw-receiver-extension.housing_od":1.418,"sb-tactical-sbpdw-receiver-extension.latch_width":0.35,"sb-tactical-sbpdw-receiver-extension.lever_width":0.3,"sb-tactical-sbpdw-receiver-extension.nut_length":0.7,"sb-tactical-sbpdw-receiver-extension.nut_notch_count":8,"sb-tactical-sbpdw-receiver-extension.nut_notch_depth":0.2,"sb-tactical-sbpdw-receiver-extension.nut_notch_width":0.11,"sb-tactical-sbpdw-receiver-extension.nut_od":1.389,"sb-tactical-sbpdw-receiver-extension.rear_wall":0.072,"sb-tactical-sbpdw-receiver-extension.rod_bore_d":0.35,"sb-tactical-sbpdw-receiver-extension.tube_front_behind_pin":0.669,"sb-tactical-sbpdw-receiver-extension.tube_length":6.992,"sb-tactical-sbpdw-receiver-extension.tube_od":1.141,"std.receiver_extension.thread_length":1.181,"std.receiver_extension.thread_major_d":1.1813,"std.receiver_extension.thread_minor_d":1.1093,"std.receiver_extension.thread_pitch":0.0625},"profiles":{"side":[[1.016,-1.167],[1.022,-1.262],[1.048,-1.288],[1.125,-1.288],[1.146,-1.309],[1.152,-1.38],[1.172,-1.395],[1.432,-1.389],[1.71,-1.283],[1.864,-1.265],[3.146,-1.259],[3.312,-1.271],[3.324,-1.259],[3.554,-1.259],[3.563,-1.132],[3.598,-1.114],[3.598,-0.564],[3.158,-0.561],[3.143,-0.547],[3.143,0.6],[3.114,0.618],[3.114,0.677],[3.099,0.697],[3.081,0.709],[1.763,0.715],[1.178,0.715],[1.14,0.677],[1.122,0.618],[1.122,-1.15],[1.107,-1.164]]},"features":{"side":{"lever":[[[3.566,-1.238],[3.33,-1.238],[3.33,-1.936],[3.566,-1.936]]],"latch":[[[3.134,-1.238],[2.484,-1.238],[2.484,-1.593],[3.134,-1.593]]]}},"placement":{"side":{"plane":"xy","offset":{}}},"bounds":{"min":[0.669,-1.936,-0.8445],"max":[7.661,0.709,0.8445]},"volume_in3":5.6126,"centroid":[2.9676,-0.4242,0],"shell":[3.4257,-0.1804,-0.0001],"area_in2":85.0407,"triangles":32576,"manifold":true,"slabs":[[0.669,-1.26,-0.786,1.057,0.591,0.786],[1.057,-1.26,-0.845,2.223,0.709,0.845],[2.223,-1.593,-0.845,3,0.709,0.845],[3,-1.936,-0.845,3.777,0.709,0.845],[3.777,-0.695,-0.695,4.165,0.695,0.695],[4.165,-0.571,-0.571,7.661,0.571,0.571]],"slots":["tube","housing"]},"scalarworks-leap-01-micro-142":{"part":"scalarworks-leap-01-micro-142","model":"scalarworks-leap-01-micro-142.glb","script":"scalarworks_leap_micro.py","inputs":{"scalarworks-leap-01-micro-142.body_width":0.94,"scalarworks-leap-01-micro-142.clamp_below_rail":0.234,"scalarworks-leap-01-micro-142.clamp_front":0.673,"scalarworks-leap-01-micro-142.clamp_rear":0.88,"scalarworks-leap-01-micro-142.deck_above_rail":0.831,"scalarworks-leap-01-micro-142.deck_x":0.195,"scalarworks-leap-01-micro-142.edge_break":0.008,"scalarworks-leap-01-micro-142.guide_pin_d":0.1,"scalarworks-leap-01-micro-142.guide_pin_x":0.53,"scalarworks-leap-01-micro-142.head_hole_depth":0.04,"scalarworks-leap-01-micro-142.head_ring":0.008,"scalarworks-leap-01-micro-142.hook_top":-0.056,"scalarworks-leap-01-micro-142.jaw_inner_z":0.51,"scalarworks-leap-01-micro-142.jaw_top":0.195,"scalarworks-leap-01-micro-142.set_screw_d":0.106,"scalarworks-leap-01-micro-142.set_screw_hole_depth":0.1,"scalarworks-leap-01-micro-142.set_screw_recess":0.02,"scalarworks-leap-01-micro-142.set_screw_z":0.579,"scalarworks-leap-01-micro-142.shaft_end_d":0.15,"scalarworks-leap-01-micro-142.wheel_axis_above_rail":0,"scalarworks-leap-01-micro-142.wheel_d":0.632,"scalarworks-leap-01-micro-142.wheel_dish_depth":0.01,"scalarworks-leap-01-micro-142.wheel_face_d":0.57,"scalarworks-leap-01-micro-142.wheel_hub_d":0.117,"scalarworks-leap-01-micro-142.wheel_outer_z":0.663,"scalarworks-leap-01-micro-142.wheel_pocket_gap":0.02,"scalarworks-leap-01-micro-142.wheel_root_d":0.527,"scalarworks-leap-01-micro-142.wheel_socket_depth":0.08,"scalarworks-leap-01-micro-142.wheel_thickness":0.167,"scalarworks-leap-01-micro-142.width":1.334,"std.density.aluminium_7075":1.632,"std.density.steel":4.565,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{"side":[[-0.938,0.105],[-0.938,0.02],[-0.908,0.018],[-0.89,0],[-0.888,-0.233],[0.673,-0.233],[0.991,0.555],[1.028,0.612],[1.093,0.669],[1.109,0.709],[1.133,0.73],[1.133,0.811],[1.101,0.823],[1.093,0.884],[1.071,0.906],[-0.653,0.906],[-0.667,0.892],[-0.667,0.847],[-0.683,0.807],[-0.721,0.772],[-0.876,0.683],[-0.89,0.665],[-0.898,0.191],[-0.91,0.13],[-0.924,0.107]],"end":[[-0.673,-0.004],[-0.664,-0.223],[-0.654,-0.227],[-0.365,-0.23],[-0.358,-0.17],[-0.416,-0.111],[-0.416,-0.09],[-0.318,0.008],[0.317,0.008],[0.418,-0.094],[0.418,-0.109],[0.356,-0.171],[0.362,-0.23],[0.529,-0.231],[0.561,-0.216],[0.602,-0.178],[0.642,-0.138],[0.666,-0.094],[0.669,0.218],[0.646,0.277],[0.507,0.416],[0.478,0.469],[0.471,0.892],[0.306,0.893],[0.27,0.813],[-0.231,0.814],[-0.267,0.814],[-0.28,0.827],[-0.305,0.893],[-0.47,0.893],[-0.475,0.479],[-0.496,0.432],[-0.53,0.395],[-0.609,0.315],[-0.639,0.316],[-0.664,0.29]]},"features":{"side":{"window":[[[0.618,0.559],[0.594,0.628],[0.543,0.679],[0.466,0.703],[-0.093,0.712],[-0.178,0.695],[-0.247,0.667],[-0.421,0.545],[-0.48,0.478],[-0.5,0.426],[-0.505,0.247],[-0.496,0.199],[-0.476,0.162],[-0.434,0.124],[-0.401,0.107],[-0.344,0.099],[-0.278,0.109],[-0.286,0.142],[-0.271,0.156],[-0.251,0.156],[-0.229,0.178],[-0.229,0.219],[-0.215,0.233],[-0.178,0.229],[-0.156,0.247],[-0.138,0.286],[-0.089,0.274],[-0.044,0.314],[-0.004,0.29],[0.02,0.29],[0.061,0.31],[0.085,0.278],[0.106,0.27],[0.154,0.278],[0.164,0.243],[0.183,0.225],[0.227,0.221],[0.237,0.211],[0.233,0.174],[0.256,0.148],[0.29,0.134],[0.282,0.109],[0.288,0.103],[0.337,0.107],[0.361,0.099],[0.41,0.111],[0.464,0.154],[0.493,0.199],[0.606,0.474]]]},"end":{"window":[[[0.233,0.698],[0.259,0.694],[0.282,0.682],[0.3,0.664],[0.311,0.641],[0.316,0.615],[0.315,0.264],[0.311,0.239],[0.3,0.216],[0.281,0.198],[0.258,0.186],[0.233,0.182],[-0.233,0.182],[-0.259,0.187],[-0.282,0.198],[-0.3,0.216],[-0.312,0.239],[-0.316,0.265],[-0.316,0.616],[-0.311,0.642],[-0.3,0.665],[-0.282,0.683],[-0.259,0.694],[-0.233,0.699]]]}},"placement":{"side":{"plane":"xy","offset":{}},"end":{"plane":"zy","offset":{}}},"bounds":{"min":[-0.88,-0.3156,-0.669],"max":[1.133,0.831,0.669]},"volume_in3":0.9246,"centroid":[0.0169,0.2814,-0.0051],"shell":[0.0195,0.2703,0.0095],"area_in2":15.9037,"triangles":4258,"manifold":true,"rail_seat":{"x":[-0.88,0.673],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-0.88,-0.231,-0.669,-0.209,0.831,0.669],[-0.209,-0.316,-0.663,0.127,0.831,0.668],[0.127,-0.264,-0.669,0.798,0.831,0.669],[0.798,0.076,-0.669,1.133,0.831,0.669]],"slots":["mount","hardware"]},"scalarworks-leap-01-micro-157":{"part":"scalarworks-leap-01-micro-157","model":"scalarworks-leap-01-micro-157.glb","script":"scalarworks_leap_micro.py","inputs":{"scalarworks-leap-01-micro-157.body_width":0.94,"scalarworks-leap-01-micro-157.clamp_below_rail":0.234,"scalarworks-leap-01-micro-157.clamp_front":0.679,"scalarworks-leap-01-micro-157.clamp_rear":0.878,"scalarworks-leap-01-micro-157.deck_above_rail":0.981,"scalarworks-leap-01-micro-157.deck_x":0.28,"scalarworks-leap-01-micro-157.edge_break":0.008,"scalarworks-leap-01-micro-157.guide_pin_d":0.1,"scalarworks-leap-01-micro-157.guide_pin_x":0.53,"scalarworks-leap-01-micro-157.head_hole_depth":0.04,"scalarworks-leap-01-micro-157.head_ring":0.008,"scalarworks-leap-01-micro-157.hook_top":-0.056,"scalarworks-leap-01-micro-157.jaw_inner_z":0.51,"scalarworks-leap-01-micro-157.jaw_top":0.195,"scalarworks-leap-01-micro-157.set_screw_d":0.106,"scalarworks-leap-01-micro-157.set_screw_hole_depth":0.1,"scalarworks-leap-01-micro-157.set_screw_recess":0.02,"scalarworks-leap-01-micro-157.set_screw_z":0.579,"scalarworks-leap-01-micro-157.shaft_end_d":0.15,"scalarworks-leap-01-micro-157.wheel_axis_above_rail":0.002,"scalarworks-leap-01-micro-157.wheel_d":0.629,"scalarworks-leap-01-micro-157.wheel_dish_depth":0.01,"scalarworks-leap-01-micro-157.wheel_face_d":0.572,"scalarworks-leap-01-micro-157.wheel_hub_d":0.13,"scalarworks-leap-01-micro-157.wheel_outer_z":0.663,"scalarworks-leap-01-micro-157.wheel_pocket_gap":0.02,"scalarworks-leap-01-micro-157.wheel_root_d":0.527,"scalarworks-leap-01-micro-157.wheel_socket_depth":0.08,"scalarworks-leap-01-micro-157.wheel_thickness":0.167,"scalarworks-leap-01-micro-157.width":1.334,"std.density.aluminium_7075":1.632,"std.density.steel":4.565,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{"side":[[-0.937,0.095],[-0.937,0.022],[-0.906,0.02],[-0.888,0.002],[-0.88,-0.051],[-0.888,-0.059],[-0.888,-0.103],[-0.878,-0.069],[-0.868,-0.087],[-0.868,-0.112],[-0.888,-0.116],[-0.886,-0.227],[0.679,-0.227],[0.835,0.136],[1.046,0.683],[1.095,0.768],[1.16,0.825],[1.176,0.866],[1.2,0.886],[1.2,0.967],[1.168,0.983],[1.156,1.048],[1.137,1.062],[1.109,1.066],[-0.586,1.062],[-0.6,1.048],[-0.604,0.995],[-0.643,0.953],[-0.841,0.839],[-0.878,0.815],[-0.888,0.797],[-0.896,0.193],[-0.908,0.124]],"end":[[-0.671,-0.005],[-0.662,-0.223],[-0.652,-0.227],[-0.364,-0.23],[-0.356,-0.17],[-0.415,-0.111],[-0.415,-0.091],[-0.317,0.008],[0.315,0.007],[0.417,-0.094],[0.417,-0.109],[0.355,-0.171],[0.361,-0.229],[0.527,-0.231],[0.583,-0.196],[0.64,-0.139],[0.664,-0.094],[0.667,0.217],[0.643,0.276],[0.505,0.414],[0.473,0.479],[0.469,1.048],[0.304,1.048],[0.282,0.985],[0.266,0.965],[-0.251,0.966],[-0.266,0.966],[-0.279,0.979],[-0.304,1.048],[-0.469,1.048],[-0.473,0.477],[-0.494,0.43],[-0.543,0.378],[-0.607,0.314],[-0.637,0.314],[-0.662,0.289]]},"features":{"side":{"window":[[[0.681,0.679],[0.681,0.724],[0.665,0.772],[0.622,0.823],[0.553,0.856],[-0.116,0.864],[-0.205,0.839],[-0.253,0.815],[-0.432,0.689],[-0.474,0.639],[-0.499,0.578],[-0.503,0.249],[-0.495,0.201],[-0.483,0.172],[-0.448,0.134],[-0.371,0.101],[-0.282,0.101],[-0.276,0.107],[-0.284,0.144],[-0.235,0.168],[-0.227,0.221],[-0.217,0.231],[-0.184,0.227],[-0.162,0.241],[-0.144,0.284],[-0.087,0.276],[-0.055,0.312],[-0.034,0.312],[-0.01,0.292],[0.018,0.292],[0.043,0.312],[0.059,0.312],[0.091,0.276],[0.148,0.284],[0.162,0.266],[0.162,0.249],[0.184,0.227],[0.221,0.227],[0.235,0.217],[0.235,0.176],[0.253,0.154],[0.292,0.136],[0.284,0.116],[0.29,0.101],[0.387,0.101],[0.428,0.122],[0.474,0.164],[0.491,0.193],[0.665,0.622]]]},"end":{"window":[[[0.232,0.851],[0.258,0.847],[0.281,0.835],[0.299,0.817],[0.31,0.794],[0.315,0.768],[0.314,0.263],[0.31,0.237],[0.299,0.214],[0.28,0.196],[0.257,0.185],[0.232,0.181],[-0.233,0.181],[-0.258,0.185],[-0.281,0.197],[-0.299,0.215],[-0.311,0.238],[-0.315,0.263],[-0.315,0.769],[-0.31,0.795],[-0.299,0.817],[-0.281,0.836],[-0.258,0.847],[-0.232,0.851]]]}},"placement":{"side":{"plane":"xy","offset":{}},"end":{"plane":"zy","offset":{}}},"bounds":{"min":[-0.878,-0.3122,-0.667],"max":[1.2,0.981,0.667]},"volume_in3":0.9534,"centroid":[0.0374,0.3379,-0.0053],"shell":[0.0364,0.3296,0.009],"area_in2":16.555,"triangles":4294,"manifold":true,"rail_seat":{"x":[-0.878,0.679],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-0.878,-0.252,-0.667,-0.185,0.981,0.667],[-0.185,-0.312,-0.663,0.161,0.981,0.666],[0.161,-0.261,-0.667,0.854,0.981,0.667],[0.854,0.184,-0.667,1.2,0.981,0.667]],"slots":["mount","hardware"]},"scalarworks-leap-01-micro-193":{"part":"scalarworks-leap-01-micro-193","model":"scalarworks-leap-01-micro-193.glb","script":"scalarworks_leap_micro.py","inputs":{"scalarworks-leap-01-micro-193.body_width":0.94,"scalarworks-leap-01-micro-193.clamp_below_rail":0.234,"scalarworks-leap-01-micro-193.clamp_front":0.669,"scalarworks-leap-01-micro-193.clamp_rear":0.878,"scalarworks-leap-01-micro-193.deck_above_rail":1.341,"scalarworks-leap-01-micro-193.deck_x":0.364,"scalarworks-leap-01-micro-193.edge_break":0.008,"scalarworks-leap-01-micro-193.guide_pin_d":0.1,"scalarworks-leap-01-micro-193.guide_pin_x":0.53,"scalarworks-leap-01-micro-193.head_hole_depth":0.04,"scalarworks-leap-01-micro-193.head_ring":0.008,"scalarworks-leap-01-micro-193.hook_top":-0.056,"scalarworks-leap-01-micro-193.jaw_inner_z":0.51,"scalarworks-leap-01-micro-193.jaw_top":0.195,"scalarworks-leap-01-micro-193.set_screw_d":0.106,"scalarworks-leap-01-micro-193.set_screw_hole_depth":0.1,"scalarworks-leap-01-micro-193.set_screw_recess":0.02,"scalarworks-leap-01-micro-193.set_screw_z":0.579,"scalarworks-leap-01-micro-193.shaft_end_d":0.15,"scalarworks-leap-01-micro-193.wheel_axis_above_rail":-0.008,"scalarworks-leap-01-micro-193.wheel_d":0.631,"scalarworks-leap-01-micro-193.wheel_dish_depth":0.01,"scalarworks-leap-01-micro-193.wheel_face_d":0.565,"scalarworks-leap-01-micro-193.wheel_hub_d":0.138,"scalarworks-leap-01-micro-193.wheel_outer_z":0.663,"scalarworks-leap-01-micro-193.wheel_pocket_gap":0.02,"scalarworks-leap-01-micro-193.wheel_root_d":0.523,"scalarworks-leap-01-micro-193.wheel_socket_depth":0.08,"scalarworks-leap-01-micro-193.wheel_thickness":0.167,"scalarworks-leap-01-micro-193.width":1.334,"std.density.aluminium_7075":1.632,"std.density.steel":4.565,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{"side":[[-0.937,0.103],[-0.937,0.022],[-0.907,0.016],[-0.888,0.002],[-0.886,-0.243],[0.669,-0.243],[0.761,-0.01],[0.789,0.034],[1.162,0.978],[1.214,1.068],[1.263,1.112],[1.287,1.205],[1.316,1.242],[1.316,1.319],[1.279,1.339],[1.271,1.4],[1.249,1.418],[-0.473,1.418],[-0.483,1.408],[-0.487,1.359],[-0.526,1.309],[-0.83,1.134],[-0.892,1.084],[-0.896,0.225],[-0.913,0.132],[-0.921,0.111]],"end":[[-0.673,-0.005],[-0.664,-0.223],[-0.654,-0.227],[-0.365,-0.231],[-0.358,-0.17],[-0.416,-0.111],[-0.416,-0.09],[-0.318,0.008],[0.316,0.008],[0.418,-0.094],[0.418,-0.109],[0.356,-0.171],[0.362,-0.23],[0.529,-0.231],[0.561,-0.216],[0.617,-0.163],[0.651,-0.127],[0.666,-0.094],[0.669,0.339],[0.645,0.395],[0.51,0.531],[0.475,0.599],[0.471,1.405],[0.306,1.406],[0.27,1.326],[0.182,1.326],[-0.27,1.326],[-0.305,1.406],[-0.47,1.406],[-0.472,0.614],[-0.499,0.547],[-0.643,0.399],[-0.667,0.355]]},"features":{"side":{"window":[[[0.805,1.027],[0.789,1.096],[0.761,1.14],[0.718,1.179],[0.633,1.211],[0.037,1.219],[-0.084,1.195],[-0.396,0.984],[-0.447,0.938],[-0.483,0.881],[-0.503,0.8],[-0.503,0.261],[-0.495,0.205],[-0.463,0.152],[-0.424,0.122],[-0.404,0.117],[-0.4,0.101],[-0.38,0.113],[-0.291,0.109],[-0.289,0.136],[-0.258,0.146],[-0.232,0.172],[-0.232,0.213],[-0.177,0.223],[-0.145,0.275],[-0.104,0.263],[-0.088,0.267],[-0.056,0.304],[-0.007,0.28],[0.054,0.304],[0.09,0.263],[0.147,0.271],[0.157,0.237],[0.175,0.219],[0.212,0.219],[0.23,0.205],[0.23,0.156],[0.287,0.128],[0.279,0.103],[0.285,0.097],[0.337,0.093],[0.402,0.101],[0.404,0.115],[0.455,0.146],[0.489,0.192],[0.797,0.958]]]},"end":{"window":[[[0.233,1.182],[0.259,1.177],[0.282,1.166],[0.3,1.148],[0.312,1.125],[0.316,1.099],[0.315,0.264],[0.311,0.239],[0.299,0.216],[0.281,0.197],[0.258,0.186],[0.232,0.182],[-0.233,0.182],[-0.259,0.186],[-0.282,0.198],[-0.3,0.216],[-0.312,0.239],[-0.316,0.265],[-0.315,1.099],[-0.311,1.125],[-0.3,1.148],[-0.281,1.166],[-0.258,1.178],[-0.233,1.182]]]}},"placement":{"side":{"plane":"xy","offset":{}},"end":{"plane":"zy","offset":{}}},"bounds":{"min":[-0.878,-0.3231,-0.669],"max":[1.316,1.341,0.669]},"volume_in3":1.1131,"centroid":[0.0728,0.4983,-0.004],"shell":[0.0676,0.4757,0.0077],"area_in2":18.5208,"triangles":4380,"manifold":true,"rail_seat":{"x":[-0.878,0.669],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-0.878,-0.272,-0.669,-0.147,1.341,0.669],[-0.147,-0.323,-0.663,0.219,1.341,0.667],[0.219,-0.231,-0.669,0.95,1.341,0.669],[0.95,0.442,-0.598,1.316,1.341,0.598]],"slots":["mount","hardware"]},"scalarworks-leap-02-micro-226":{"part":"scalarworks-leap-02-micro-226","model":"scalarworks-leap-02-micro-226.glb","script":"scalarworks_leap_micro.py","inputs":{"scalarworks-leap-02-micro-226.body_width":0.94,"scalarworks-leap-02-micro-226.clamp_below_rail":0.236,"scalarworks-leap-02-micro-226.clamp_front":0.887,"scalarworks-leap-02-micro-226.clamp_rear":0.884,"scalarworks-leap-02-micro-226.deck_above_rail":1.671,"scalarworks-leap-02-micro-226.deck_x":0.328,"scalarworks-leap-02-micro-226.edge_break":0.008,"scalarworks-leap-02-micro-226.end_raise":0.33,"scalarworks-leap-02-micro-226.guide_pin_d":0.1,"scalarworks-leap-02-micro-226.guide_pin_x":0.53,"scalarworks-leap-02-micro-226.head_hole_depth":0.04,"scalarworks-leap-02-micro-226.head_ring":0.008,"scalarworks-leap-02-micro-226.hook_top":-0.056,"scalarworks-leap-02-micro-226.jaw_inner_z":0.51,"scalarworks-leap-02-micro-226.jaw_top":0.195,"scalarworks-leap-02-micro-226.set_screw_d":0.106,"scalarworks-leap-02-micro-226.set_screw_hole_depth":0.1,"scalarworks-leap-02-micro-226.set_screw_recess":0.02,"scalarworks-leap-02-micro-226.set_screw_z":0.579,"scalarworks-leap-02-micro-226.shaft_end_d":0.15,"scalarworks-leap-02-micro-226.wheel_axis_above_rail":-0.032,"scalarworks-leap-02-micro-226.wheel_d":0.627,"scalarworks-leap-02-micro-226.wheel_dish_depth":0.01,"scalarworks-leap-02-micro-226.wheel_face_d":0.54,"scalarworks-leap-02-micro-226.wheel_hub_d":0.122,"scalarworks-leap-02-micro-226.wheel_outer_z":0.663,"scalarworks-leap-02-micro-226.wheel_pocket_gap":0.02,"scalarworks-leap-02-micro-226.wheel_root_d":0.577,"scalarworks-leap-02-micro-226.wheel_socket_depth":0.08,"scalarworks-leap-02-micro-226.wheel_thickness":0.167,"scalarworks-leap-02-micro-226.width":1.334,"scalarworks-leap-02-micro-226.window_step":0.027,"scalarworks-leap-02-micro-226.window_step_depth":0.02,"std.density.aluminium_7075":1.632,"std.density.steel":4.565,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{"side":[[-0.942,0.14],[-0.942,0.03],[-0.914,0.006],[-0.887,0.003],[-0.887,-0.038],[-0.865,-0.1],[-0.868,-0.117],[-0.887,-0.118],[-0.886,-0.237],[0.887,-0.237],[0.901,0.003],[0.93,0.014],[0.946,0.033],[0.946,0.138],[0.871,0.431],[0.645,1.209],[0.635,1.309],[0.668,1.377],[0.734,1.421],[1.274,1.561],[1.302,1.58],[1.325,1.643],[1.316,1.657],[1.292,1.658],[1.302,1.723],[1.276,1.739],[-0.588,1.732],[-0.601,1.681],[-0.657,0.793],[-0.674,0.76],[-0.71,0.724],[-0.866,0.633],[-0.89,0.609],[-0.897,0.582],[-0.902,0.306]],"end":[[-0.673,-0.005],[-0.664,-0.223],[-0.654,-0.227],[-0.365,-0.231],[-0.358,-0.17],[-0.416,-0.111],[-0.416,-0.09],[-0.318,0.008],[0.316,0.008],[0.418,-0.094],[0.418,-0.109],[0.356,-0.171],[0.362,-0.23],[0.529,-0.231],[0.561,-0.216],[0.617,-0.163],[0.651,-0.127],[0.666,-0.094],[0.669,0.339],[0.645,0.395],[0.51,0.531],[0.475,0.599],[0.471,1.405],[0.306,1.406],[0.27,1.326],[0.182,1.326],[-0.27,1.326],[-0.305,1.406],[-0.47,1.406],[-0.472,0.614],[-0.499,0.547],[-0.643,0.399],[-0.667,0.355]]},"features":{"side":{"window":[[[0.435,0.609],[0.229,1.327],[0.199,1.395],[0.17,1.426],[0.127,1.448],[0.08,1.456],[-0.186,1.448],[-0.241,1.421],[-0.268,1.395],[-0.295,1.342],[-0.308,1.239],[-0.353,0.424],[-0.343,0.391],[-0.307,0.342],[-0.259,0.312],[-0.209,0.3],[0.203,0.3],[0.24,0.307],[0.28,0.327],[0.314,0.359],[0.409,0.484],[0.432,0.529]]]},"end":{"window":[[[0.233,1.182],[0.259,1.177],[0.282,1.166],[0.3,1.148],[0.312,1.125],[0.316,1.099],[0.315,0.264],[0.311,0.239],[0.299,0.216],[0.281,0.197],[0.258,0.186],[0.232,0.182],[-0.233,0.182],[-0.259,0.186],[-0.282,0.198],[-0.3,0.216],[-0.312,0.239],[-0.316,0.265],[-0.315,1.099],[-0.311,1.125],[-0.3,1.148],[-0.281,1.166],[-0.258,1.178],[-0.233,1.182]]]}},"placement":{"side":{"plane":"xy","offset":{}},"end":{"plane":"zy","offset":{}}},"bounds":{"min":[-0.884,-0.3452,-0.669],"max":[1.325,1.671,0.669]},"volume_in3":1.4352,"centroid":[0.0847,0.5594,-0.0005],"shell":[0.0803,0.5726,0.0234],"area_in2":21.2854,"triangles":5352,"manifold":true,"rail_seat":{"x":[-0.884,0.887],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-0.884,-0.231,-0.669,-0.516,1.671,0.669],[-0.516,-0.294,-0.669,-0.148,1.671,0.669],[-0.148,-0.345,-0.668,0.22,1.671,0.668],[0.22,-0.231,-0.669,0.957,1.671,0.669],[0.957,1.479,-0.472,1.325,1.671,0.472]],"slots":["mount","hardware"]},"scalarworks-leap-08-30mm-mount":{"part":"scalarworks-leap-08-30mm-mount","model":"scalarworks-leap-08-30mm-mount.glb","script":"scalarworks_leap_08_30mm_mount.py","inputs":{"scalarworks-leap-08-30mm-mount.base_left_z":0.6653543307086613,"scalarworks-leap-08-30mm-mount.base_right_z":0.6535433070866142,"scalarworks-leap-08-30mm-mount.block_shoulder_y":0.16929133858267714,"scalarworks-leap-08-30mm-mount.block_shoulder_z":0.5984251968503936,"scalarworks-leap-08-30mm-mount.block_side_top":0.0748031496062992,"scalarworks-leap-08-30mm-mount.cap_hole_d":0.21653543307086615,"scalarworks-leap-08-30mm-mount.cap_hole_spacing":0.48425196850393704,"scalarworks-leap-08-30mm-mount.cap_pocket_floor":0.21456692913385828,"scalarworks-leap-08-30mm-mount.cap_pocket_inner_z":0.6299212598425197,"scalarworks-leap-08-30mm-mount.cap_pocket_length":0.7775590551181102,"scalarworks-leap-08-30mm-mount.cap_screw_head_d":0.2047244094488189,"scalarworks-leap-08-30mm-mount.cap_screw_head_h":0.02952755905511811,"scalarworks-leap-08-30mm-mount.cap_screw_pitch":0.2795275590551181,"scalarworks-leap-08-30mm-mount.cap_screw_z":0.7381889763779528,"scalarworks-leap-08-30mm-mount.clamp_spacing":2.364,"scalarworks-leap-08-30mm-mount.clamp_top_above_rail":0.28346456692913385,"scalarworks-leap-08-30mm-mount.edge_break":0.005,"scalarworks-leap-08-30mm-mount.flute_front_x":4.633858267716535,"scalarworks-leap-08-30mm-mount.flute_pitch":0.03110236220472441,"scalarworks-leap-08-30mm-mount.flute_rear_x":3.149606299212598,"scalarworks-leap-08-30mm-mount.flute_runout":0.22440944881889766,"scalarworks-leap-08-30mm-mount.flute_step_depth":0.015748031496062992,"scalarworks-leap-08-30mm-mount.flute_top_below_axis":1.1913385826771654,"scalarworks-leap-08-30mm-mount.front_block_rear_x":1.7322834645669292,"scalarworks-leap-08-30mm-mount.front_block_toe_x":2.822834645669291,"scalarworks-leap-08-30mm-mount.front_block_top_x":2.97244094488189,"scalarworks-leap-08-30mm-mount.hook_below_rail":0.22834645669291337,"scalarworks-leap-08-30mm-mount.jaw_end_inset":0.07874015748031496,"scalarworks-leap-08-30mm-mount.lug_depth":0.0905511811023622,"scalarworks-leap-08-30mm-mount.lug_length":0.19881889763779526,"scalarworks-leap-08-30mm-mount.lug_width":0.2755905511811024,"scalarworks-leap-08-30mm-mount.lug_x":1.1811023622047243,"scalarworks-leap-08-30mm-mount.mount_length":3.37007874015748,"scalarworks-leap-08-30mm-mount.optical_axis_above_rail":1.57,"scalarworks-leap-08-30mm-mount.pedestal_hole_below_axis":0.8622047244094487,"scalarworks-leap-08-30mm-mount.pedestal_hole_d":0.1468503937007874,"scalarworks-leap-08-30mm-mount.pedestal_hole_spacing":0.4622047244094488,"scalarworks-leap-08-30mm-mount.pedestal_recess_depth":0.23622047244094488,"scalarworks-leap-08-30mm-mount.pedestal_recess_h":0.3031496062992126,"scalarworks-leap-08-30mm-mount.pedestal_recess_length":0.7637795275590551,"scalarworks-leap-08-30mm-mount.pedestal_width":0.6929133858267718,"scalarworks-leap-08-30mm-mount.rear_block_front_x":0.6220472440944882,"scalarworks-leap-08-30mm-mount.rear_block_rear_x":0.547244094488189,"scalarworks-leap-08-30mm-mount.rib_depth":0.011811023622047244,"scalarworks-leap-08-30mm-mount.rib_length":0.7440944881889763,"scalarworks-leap-08-30mm-mount.rib_pitch":0.03220472440944882,"scalarworks-leap-08-30mm-mount.rib_top_below_axis":0.25196850393700787,"scalarworks-leap-08-30mm-mount.ring_bore":1.1811023622047243,"scalarworks-leap-08-30mm-mount.ring_cap_shoulder_width":1.669291338582677,"scalarworks-leap-08-30mm-mount.ring_cap_side_flat":0.1220472440944882,"scalarworks-leap-08-30mm-mount.ring_end_chamfer":0.04133858267716536,"scalarworks-leap-08-30mm-mount.ring_front_x":4.488188976377953,"scalarworks-leap-08-30mm-mount.ring_gap":2.3622047244094486,"scalarworks-leap-08-30mm-mount.ring_length":0.9448818897637795,"scalarworks-leap-08-30mm-mount.ring_lower_chamfer_drop":0.30708661417322836,"scalarworks-leap-08-30mm-mount.ring_lower_r":0.7519685039370079,"scalarworks-leap-08-30mm-mount.ring_lower_side_flat":0.17716535433070865,"scalarworks-leap-08-30mm-mount.ring_lower_width":1.68503937007874,"scalarworks-leap-08-30mm-mount.ring_rear_x":1.1811023622047243,"scalarworks-leap-08-30mm-mount.ring_top_above_axis":0.7133858267716535,"scalarworks-leap-08-30mm-mount.ring_top_flat_width":0.7992125984251969,"scalarworks-leap-08-30mm-mount.ring_width":1.7440944881889762,"scalarworks-leap-08-30mm-mount.shaft_d":0.15433070866141732,"scalarworks-leap-08-30mm-mount.side_pocket_corner_r":0.10236220472440945,"scalarworks-leap-08-30mm-mount.side_pocket_depth":0.19685039370078738,"scalarworks-leap-08-30mm-mount.side_pocket_front_x":1.6811023622047245,"scalarworks-leap-08-30mm-mount.side_pocket_rear_x":0.6811023622047244,"scalarworks-leap-08-30mm-mount.side_pocket_top":0.46299212598425193,"scalarworks-leap-08-30mm-mount.split_groove_depth":0.012,"scalarworks-leap-08-30mm-mount.split_groove_width":0.008,"scalarworks-leap-08-30mm-mount.under_pocket_depth":0.19685039370078738,"scalarworks-leap-08-30mm-mount.under_pocket_front_x":4.460629921259843,"scalarworks-leap-08-30mm-mount.under_pocket_rear_x":3.7559055118110236,"scalarworks-leap-08-30mm-mount.under_pocket_width":0.3543307086614173,"scalarworks-leap-08-30mm-mount.weight":5.6791078738824465,"scalarworks-leap-08-30mm-mount.wheel_axis_below_rail":0.010236220472440945,"scalarworks-leap-08-30mm-mount.wheel_d":0.6299212598425197,"scalarworks-leap-08-30mm-mount.wheel_dish_depth":0.015748031496062992,"scalarworks-leap-08-30mm-mount.wheel_face_d":0.5177165354330708,"scalarworks-leap-08-30mm-mount.wheel_outer_z":0.6811023622047244,"scalarworks-leap-08-30mm-mount.wheel_pocket_gap":0.011811023622047244,"scalarworks-leap-08-30mm-mount.wheel_root_d":0.5826771653543308,"scalarworks-leap-08-30mm-mount.wheel_thickness":0.18503937007874016,"std.density.aluminium_7075":1.632,"std.density.steel":4.565,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{"mount":[[-0.628,-1.355],[-0.628,-1.57],[0.509,-1.57],[2.685,-1.57],[2.694,-1.56],[2.901,-1.56],[2.909,-1.568],[2.958,-1.511],[3.026,-1.489],[4.739,-1.282],[4.78,-1.263],[4.808,-1.22],[4.959,-0.828],[4.959,0.678],[4.919,0.713],[4.053,0.713],[4.014,0.674],[4.014,-0.839],[3.984,-0.911],[3.94,-0.958],[3.88,-0.992],[3.846,-0.999],[1.817,-0.999],[1.757,-0.977],[1.691,-0.919],[1.665,-0.873],[1.654,-0.824],[1.654,0.678],[1.614,0.713],[0.748,0.713],[0.709,0.674],[0.709,-0.858],[0.675,-0.941],[0.609,-0.999],[0.545,-1.022],[-0.543,-1.154]]},"features":{"mount":{}},"placement":{"mount":{"plane":"xy","offset":{"y":"optical_axis_above_rail"}}},"bounds":{"min":[-0.628,-0.3248,-0.872],"max":[4.9606,2.2834,0.872]},"axis_y":1.57,"volume_in3":3.8628,"centroid":[2.1995,0.7692,-0.0048],"shell":[2.2684,0.8514,-0.0062],"area_in2":48.523,"triangles":12126,"manifold":true,"rail_seat":{"x":[-0.5472,2.8228],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-0.628,-0.228,-0.681,-0.229,0.454,0.654],[-0.229,-0.325,-0.681,0.17,0.503,0.654],[0.17,-0.273,-0.681,0.57,0.557,0.654],[0.57,-0.228,-0.872,0.969,2.283,0.872],[0.969,-0.091,-0.872,1.368,2.283,0.872],[1.368,-0.228,-0.872,1.767,2.283,0.872],[1.767,-0.228,-0.681,2.166,0.589,0.654],[2.166,-0.325,-0.681,2.566,0.571,0.654],[2.566,-0.228,-0.681,2.965,0.571,0.654],[2.965,0.061,-0.405,3.364,0.571,0.402],[3.364,0.122,-0.346,3.763,0.571,0.346],[3.763,0.17,-0.872,4.561,2.283,0.872],[4.561,0.267,-0.872,4.961,2.283,0.872]],"slots":["body","hardware"]},"sig-alpha-msr-30mm":{"part":"sig-alpha-msr-30mm","model":"sig-alpha-msr-30mm.glb","script":"sig_alpha_msr_30mm.py","inputs":{"sig-alpha-msr-30mm.arm_pocket_depth":0.2,"sig-alpha-msr-30mm.arm_width":0.68,"sig-alpha-msr-30mm.base_foot_right_z":0.44,"sig-alpha-msr-30mm.base_right_z":0.6,"sig-alpha-msr-30mm.base_top_width":0.7,"sig-alpha-msr-30mm.clamp_bar_outer_z":0.56,"sig-alpha-msr-30mm.clamp_bar_thickness":0.21,"sig-alpha-msr-30mm.clamp_bolt_below_rail_top":0.01,"sig-alpha-msr-30mm.clamp_bolt_head_d":0.32,"sig-alpha-msr-30mm.clamp_bolt_head_h":0.05,"sig-alpha-msr-30mm.clamp_bolt_spacing":1.97,"sig-alpha-msr-30mm.clamp_nut_af":0.5,"sig-alpha-msr-30mm.clamp_nut_h":0.54,"sig-alpha-msr-30mm.optical_axis_above_rail":1.535,"sig-alpha-msr-30mm.ring_bore":1.1811023622047243,"sig-alpha-msr-30mm.ring_edge_bevel":0.085,"sig-alpha-msr-30mm.ring_front_x":4.645,"sig-alpha-msr-30mm.ring_length":0.628,"sig-alpha-msr-30mm.ring_lower_slot_bottom_below_split":0.62,"sig-alpha-msr-30mm.ring_od":1.363,"sig-alpha-msr-30mm.ring_rear_x":1.477,"sig-alpha-msr-30mm.ring_screw_seat_above_split":0.326,"sig-alpha-msr-30mm.ring_screw_seat_d":0.228,"sig-alpha-msr-30mm.ring_screw_slot_top_above_split":0.62,"sig-alpha-msr-30mm.ring_screw_slot_width":0.148,"sig-alpha-msr-30mm.ring_screw_spacing":0.321,"sig-alpha-msr-30mm.ring_screw_z":0.715,"sig-alpha-msr-30mm.ring_side_flat_height":0.62,"sig-alpha-msr-30mm.ring_top_flat_width":0.61,"sig-alpha-msr-30mm.ring_width":1.686,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{"mount_alone":[[-0.421,-1.315],[-0.415,-1.655],[-0.403,-1.725],[-0.388,-1.735],[-0.274,-1.737],[-0.227,-1.803],[-0.2,-1.816],[-0.081,-1.82],[0.066,-1.811],[0.093,-1.783],[0.11,-1.755],[0.11,-1.744],[0.131,-1.722],[0.136,-1.736],[0.298,-1.732],[0.322,-1.696],[0.321,-1.651],[0.376,-1.649],[1.648,-1.65],[1.655,-1.662],[1.659,-1.711],[1.666,-1.729],[1.723,-1.737],[1.774,-1.734],[1.822,-1.798],[1.862,-1.804],[1.953,-1.797],[2.091,-1.802],[2.108,-1.796],[2.124,-1.78],[2.153,-1.733],[2.332,-1.737],[2.36,-1.732],[2.367,-1.724],[2.368,-1.554],[2.374,-1.554],[2.378,-1.651],[2.387,-1.652],[2.397,-1.642],[2.47,-1.497],[2.499,-1.49],[2.512,-1.477],[2.667,-1.191],[4.471,-1.187],[4.55,-1.146],[4.797,-0.906],[4.914,-0.788],[4.933,-0.759],[4.955,-0.7],[4.992,-0.377],[4.997,-0.286],[4.995,-0.006],[4.981,0.006],[4.989,0.02],[4.992,0.329],[4.958,0.651],[4.949,0.668],[4.922,0.686],[4.679,0.687],[4.362,0.684],[4.345,0.676],[4.326,0.654],[4.327,0.578],[4.346,0.352],[4.343,0.06],[4.348,0.01],[4.338,0.014],[4.335,0.366],[4.328,0.507],[4.319,0.584],[4.311,0.596],[4.301,0.595],[4.283,0.413],[4.275,0.093],[4.281,0.045],[4.281,-0.295],[4.288,-0.453],[4.303,-0.547],[4.314,-0.544],[4.322,-0.515],[4.34,-0.218],[4.341,-0.017],[4.343,-0.005],[4.349,-0.005],[4.35,-0.104],[4.347,-0.374],[4.331,-0.569],[4.321,-0.66],[4.307,-0.685],[4.301,-0.686],[4.298,-0.703],[4.29,-0.708],[4.295,-0.671],[4.277,-0.67],[4.231,-0.723],[4.164,-0.784],[4.122,-0.81],[4.077,-0.819],[3.862,-0.818],[3.86,-0.825],[3.873,-0.829],[3.876,-0.838],[3.896,-0.838],[3.904,-0.846],[3.726,-0.848],[3.705,-0.844],[3.726,-0.842],[3.729,-0.831],[3.703,-0.831],[3.692,-0.839],[3.683,-0.831],[3.665,-0.83],[3.706,-0.828],[3.71,-0.824],[3.703,-0.819],[3.669,-0.82],[3.658,-0.826],[3.629,-0.82],[3.627,-0.826],[3.647,-0.828],[3.64,-0.833],[3.655,-0.843],[3.678,-0.842],[3.669,-0.848],[3.389,-0.85],[3.372,-0.845],[3.281,-0.849],[3.261,-0.837],[3.256,-0.846],[2.791,-0.847],[2.793,-0.834],[2.787,-0.832],[2.791,-0.819],[2.729,-0.819],[2.737,-0.831],[2.78,-0.822],[2.784,-0.832],[2.715,-0.834],[2.723,-0.845],[2.732,-0.839],[2.742,-0.843],[2.718,-0.851],[2.704,-0.851],[2.695,-0.842],[2.681,-0.848],[2.658,-0.843],[2.619,-0.849],[2.614,-0.844],[2.623,-0.839],[2.618,-0.832],[2.601,-0.837],[2.596,-0.829],[2.582,-0.846],[2.562,-0.826],[2.538,-0.836],[2.542,-0.843],[2.565,-0.84],[2.559,-0.846],[2.409,-0.847],[2.412,-0.839],[2.446,-0.841],[2.464,-0.834],[2.448,-0.824],[2.446,-0.83],[2.409,-0.83],[2.389,-0.822],[2.382,-0.826],[2.388,-0.835],[2.375,-0.848],[2.366,-0.848],[2.349,-0.845],[2.347,-0.834],[2.335,-0.834],[2.332,-0.817],[2.322,-0.818],[2.314,-0.841],[2.321,-0.843],[2.322,-0.833],[2.33,-0.831],[2.335,-0.842],[2.342,-0.844],[2.304,-0.848],[2.298,-0.84],[2.279,-0.846],[2.253,-0.818],[2.006,-0.814],[1.944,-0.792],[1.837,-0.689],[1.815,-0.649],[1.807,-0.643],[1.803,-0.647],[1.803,-0.656],[1.797,-0.656],[1.803,-0.67],[1.799,-0.674],[1.786,-0.642],[1.769,-0.395],[1.766,-0.005],[1.774,-0.007],[1.777,-0.356],[1.79,-0.537],[1.8,-0.541],[1.807,-0.525],[1.821,-0.134],[1.817,0.353],[1.81,0.497],[1.798,0.579],[1.787,0.556],[1.782,0.48],[1.774,0.012],[1.763,0.007],[1.766,0.378],[1.781,0.576],[1.78,0.653],[1.75,0.679],[1.733,0.682],[1.189,0.68],[1.16,0.65],[1.129,0.338],[1.131,0.013],[1.137,-0.001],[1.129,-0.013],[1.129,-0.353],[1.154,-0.653],[1.143,-0.698],[1.107,-0.755],[0.838,-1.075],[0.791,-1.116],[0.749,-1.142],[0.726,-1.148],[0.719,-1.144],[0.753,-1.124],[0.734,-1.114],[-0.291,-1.117],[-0.327,-1.134],[-0.332,-1.141],[-0.322,-1.148],[-0.302,-1.142],[-0.293,-1.151],[-0.214,-1.147],[-0.18,-1.153],[-0.358,-1.154],[-0.375,-1.16],[-0.382,-1.178],[-0.355,-1.18],[-0.35,-1.194],[-0.341,-1.182],[-0.335,-1.196],[-0.33,-1.182],[-0.307,-1.182],[-0.287,-1.188],[-0.282,-1.199],[-0.248,-1.196],[-0.248,-1.19],[-0.275,-1.186],[-0.239,-1.182],[-0.235,-1.189],[-0.239,-1.193],[-0.211,-1.195],[-0.207,-1.202],[-0.216,-1.207],[-0.395,-1.205],[-0.408,-1.216],[-0.413,-1.233]]},"features":{"mount_alone":{"screw_pockets":[[[4.888,0.591],[4.862,0.616],[4.78,0.616],[4.755,0.59],[4.756,0.465],[4.72,0.448],[4.707,0.4],[4.73,0.355],[4.77,0.335],[4.877,0.336],[4.917,0.356],[4.939,0.402],[4.924,0.45],[4.889,0.467]],[[4.575,0.589],[4.549,0.614],[4.459,0.613],[4.433,0.587],[4.434,0.463],[4.405,0.445],[4.391,0.397],[4.414,0.352],[4.454,0.333],[4.559,0.333],[4.598,0.354],[4.62,0.399],[4.606,0.447],[4.576,0.464]],[[1.683,0.587],[1.657,0.612],[1.567,0.611],[1.541,0.585],[1.543,0.449],[1.513,0.432],[1.499,0.385],[1.522,0.342],[1.562,0.322],[1.667,0.323],[1.706,0.343],[1.729,0.387],[1.714,0.434],[1.684,0.451]],[[1.366,0.584],[1.34,0.609],[1.249,0.608],[1.224,0.583],[1.225,0.447],[1.196,0.43],[1.182,0.383],[1.205,0.339],[1.245,0.32],[1.35,0.32],[1.389,0.341],[1.411,0.385],[1.397,0.431],[1.367,0.448]]],"lower_pockets":[[[4.906,-0.377],[4.866,-0.338],[4.787,-0.339],[4.747,-0.379],[4.749,-0.56],[4.789,-0.599],[4.868,-0.599],[4.907,-0.559]],[[4.589,-0.38],[4.549,-0.341],[4.464,-0.341],[4.424,-0.381],[4.426,-0.563],[4.466,-0.602],[4.551,-0.601],[4.59,-0.561]],[[1.702,-0.371],[1.663,-0.331],[1.578,-0.332],[1.538,-0.372],[1.54,-0.573],[1.58,-0.612],[1.665,-0.612],[1.704,-0.572]],[[1.385,-0.373],[1.345,-0.334],[1.26,-0.335],[1.221,-0.375],[1.223,-0.576],[1.263,-0.615],[1.348,-0.614],[1.387,-0.574]]],"arm_pockets":[[[4.728,-0.784],[4.326,-0.776],[4.059,-1.081],[4.097,-1.129],[4.465,-1.126],[4.751,-0.84]],[[3.987,-0.932],[2.112,-0.948],[2.084,-0.982],[2.205,-1.134],[3.881,-1.12],[4.01,-0.971]],[[1.782,-0.764],[1.196,-0.769],[0.93,-1.088],[0.964,-1.127],[2.006,-1.119],[2.034,-1.079]]],"split":[[[4.993,0.009],[4.342,0.003],[4.342,-0.008],[4.993,-0.003]],[[1.79,0.007],[1.17,0.002],[1.17,-0.01],[1.79,-0.004]]],"bar":[[[2.361,-1.212],[-0.42,-1.235],[-0.416,-1.751],[0.34,-1.744],[0.34,-1.643],[1.75,-1.631],[1.751,-1.732],[2.365,-1.727]]],"nuts":[[[2.178,-1.324],[1.747,-1.327],[1.751,-1.772],[2.182,-1.768]],[[0.133,-1.336],[-0.314,-1.339],[-0.311,-1.79],[0.137,-1.786]]]}},"placement":{"mount_alone":{"plane":"xy","offset":{"y":"optical_axis_above_rail"}}},"bounds":{"min":[-0.421,-0.2987,-1.1],"max":[4.9594,2.2165,0.843]},"axis_y":1.535,"volume_in3":3.194,"centroid":[2.034,0.633,-0.059],"shell":[2.296,0.7732,-0.0541],"area_in2":39.1566,"triangles":17320,"manifold":true,"rail_seat":{"x":[-0.421,2.516],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-0.421,-0.299,-1.1,0.348,0.42,0.65],[0.348,-0.115,-0.56,0.732,0.421,0.6],[0.732,-0.115,-0.56,1.116,0.795,0.6],[1.116,-0.115,-0.843,1.501,2.217,0.843],[1.501,-0.25,-1.1,1.885,2.217,0.843],[1.885,-0.299,-1.1,2.269,0.8,0.65],[2.269,-0.202,-0.56,2.654,0.718,0.6],[2.654,0.319,-0.34,3.806,0.716,0.34],[3.806,0.347,-0.34,4.191,0.775,0.34],[4.191,0.347,-0.843,4.575,2.217,0.843],[4.575,0.413,-0.843,4.959,2.217,0.843]],"slots":["body","hardware"]},"sig-romeo-msr-gen-2":{"part":"sig-romeo-msr-gen-2","model":"sig-romeo-msr-gen-2.glb","script":"sig_romeo_msr_gen_2.py","inputs":{"sig-romeo-msr-gen-2.base_above_clamp_bottom":1.058,"sig-romeo-msr-gen-2.clamp_bottom_y":-0.245,"sig-romeo-msr-gen-2.dial_from_front":0.96,"sig-romeo-msr-gen-2.dial_od":1.09,"sig-romeo-msr-gen-2.housing_width":0.51,"sig-romeo-msr-gen-2.left_panel_reach_z":0.68,"sig-romeo-msr-gen-2.mount_length":1.973,"sig-romeo-msr-gen-2.optical_axis_above_rail":1.41,"sig-romeo-msr-gen-2.riser_neck_width":0.856,"sig-romeo-msr-gen-2.riser_opening_bottom_above_rail":0.119,"sig-romeo-msr-gen-2.riser_opening_top_above_rail":0.558,"sig-romeo-msr-gen-2.riser_opening_width":0.841,"sig-romeo-msr-gen-2.riser_shoulder_below_top":0.197,"sig-romeo-msr-gen-2.riser_width":1.113,"sig-romeo-msr-gen-2.tube_od":1.168,"sig-romeo-msr-gen-2.turret_from_front":2.1,"sig-romeo-msr-gen-2.width":1.7637795275590549,"sig-romeo-msr-gen-2.windage_below_axis":0.05,"sig-romeo-msr-gen-2.windage_od":0.64,"sig-romeo-msr-gen-2.windage_reach_z":0.87,"sig-romeo-msr-gen-2.window_d":0.7874015748031495,"sig-romeo-msr-riser-mount.deck_above_rail":0.813,"sig-romeo-msr-riser-mount.deck_x":0,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{"side":[[-1.234,1.869],[-1.228,1.225],[-1.089,1.076],[-0.988,1.072],[-0.983,1.023],[-0.961,0.978],[-0.961,0.867],[-0.971,0.867],[-0.984,0.899],[-0.987,0.871],[-0.989,0.465],[-0.963,0.399],[-0.963,0.278],[-0.97,0.269],[-0.975,0.274],[-0.989,0.313],[-0.991,0.106],[-0.965,0.093],[-0.967,0.009],[-0.896,0],[-0.288,0.002],[-0.276,0.035],[-0.256,0.027],[0.297,0.029],[0.313,0.002],[0.375,0],[0.98,0.004],[0.991,0.908],[0.979,1.023],[0.961,1.058],[0.972,1.07],[1.103,1.072],[1.186,1.096],[1.208,1.086],[1.422,1.117],[1.442,1.127],[1.462,1.173],[1.484,1.292],[1.501,1.539],[1.501,1.779],[1.49,1.972],[1.466,2.128],[1.449,2.177],[1.434,2.192],[1.212,2.223],[1.198,2.223],[1.188,2.209],[1.112,2.227],[1.06,2.209],[1.027,2.211],[-0.18,2.443],[-0.247,2.465],[-0.291,2.467],[-0.297,2.474],[-0.375,2.482],[-0.405,2.474],[-0.446,2.484],[-0.787,2.484],[-0.863,2.472],[-1.045,2.253],[-1.062,2.238],[-1.091,2.244],[-1.224,2.103]]},"features":{"side":{"left_panel":[[[0.99,1.647],[0.974,1.695],[0.931,1.738],[0.834,1.785],[0.6,1.806],[0.21,1.816],[-0.18,1.824],[-0.317,1.836],[-0.405,1.89],[-0.492,1.929],[-0.668,1.945],[-0.843,1.92],[-0.96,1.871],[-1.032,1.828],[-1.038,1.734],[-1.019,1.578],[-0.999,1.5],[-0.96,1.422],[-0.843,1.354],[-0.687,1.321],[-0.531,1.344],[-0.414,1.393],[-0.297,1.432],[0.015,1.446],[0.405,1.461],[0.697,1.477],[0.853,1.496],[0.931,1.539],[0.974,1.598]]]}},"placement":{"side":{"plane":"xy","offset":{"y":"clamp_bottom_y"}}},"bounds":{"min":[-1.234,0,-0.68],"max":[1.501,1.426,1.0838]},"axis_y":0.597,"volume_in3":3.8275,"centroid":[0.1324,0.6079,0.1137],"shell":[0.1365,0.6073,0.1344],"area_in2":24.5003,"triangles":18640,"manifold":true,"slabs":[[-1.238,0,-0.68,-0.062,1.426,0.87],[-0.062,0,-0.68,0.329,1.362,1.084],[0.329,0,-0.68,0.721,1.287,1.084],[0.721,0,-0.68,1.113,1.212,1.084],[1.113,0.028,-0.569,1.505,1.166,0.569]],"slots":["body","hood","dial","lens"]},"sig-romeo-msr-riser-mount":{"part":"sig-romeo-msr-riser-mount","model":"sig-romeo-msr-riser-mount.glb","script":"sig_romeo_msr_gen_2.py","inputs":{"sig-romeo-msr-gen-2.base_above_clamp_bottom":1.058,"sig-romeo-msr-gen-2.clamp_bottom_y":-0.245,"sig-romeo-msr-gen-2.dial_from_front":0.96,"sig-romeo-msr-gen-2.dial_od":1.09,"sig-romeo-msr-gen-2.housing_width":0.51,"sig-romeo-msr-gen-2.left_panel_reach_z":0.68,"sig-romeo-msr-gen-2.mount_length":1.973,"sig-romeo-msr-gen-2.optical_axis_above_rail":1.41,"sig-romeo-msr-gen-2.riser_neck_width":0.856,"sig-romeo-msr-gen-2.riser_opening_bottom_above_rail":0.119,"sig-romeo-msr-gen-2.riser_opening_top_above_rail":0.558,"sig-romeo-msr-gen-2.riser_opening_width":0.841,"sig-romeo-msr-gen-2.riser_shoulder_below_top":0.197,"sig-romeo-msr-gen-2.riser_width":1.113,"sig-romeo-msr-gen-2.tube_od":1.168,"sig-romeo-msr-gen-2.turret_from_front":2.1,"sig-romeo-msr-gen-2.width":1.7637795275590549,"sig-romeo-msr-gen-2.windage_below_axis":0.05,"sig-romeo-msr-gen-2.windage_od":0.64,"sig-romeo-msr-gen-2.windage_reach_z":0.87,"sig-romeo-msr-gen-2.window_d":0.7874015748031495,"sig-romeo-msr-riser-mount.deck_above_rail":0.813,"sig-romeo-msr-riser-mount.deck_x":0,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835},"profiles":{},"features":{},"placement":{},"bounds":{"min":[-0.991,-0.245,-0.5565],"max":[0.991,0.813,0.5565]},"volume_in3":1.1494,"centroid":[0.0042,0.3682,0],"shell":[-0.0109,0.2949,0],"area_in2":15.5177,"triangles":284,"manifold":true,"rail_seat":{"x":[-0.991,0.991],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-0.991,-0.245,-0.557,0.991,0.813,0.557]],"slots":["mount"]},"sig-romeo5-gen-ii":{"part":"sig-romeo5-gen-ii","model":"sig-romeo5-gen-ii.glb","script":"sig_romeo5_gen_ii.py","inputs":{"sig-romeo5-gen-ii.base_left_z":0.649,"sig-romeo5-gen-ii.bolt_counterbore":0.05,"sig-romeo5-gen-ii.bolt_end_d":0.197,"sig-romeo5-gen-ii.bolt_end_proud":0.015,"sig-romeo5-gen-ii.button_width":0.25,"sig-romeo5-gen-ii.cap_edge_z":0.841,"sig-romeo5-gen-ii.cap_face_z":0.91,"sig-romeo5-gen-ii.cap_rim_z":0.791,"sig-romeo5-gen-ii.cap_slot_length":0.497,"sig-romeo5-gen-ii.cap_slot_width":0.127,"sig-romeo5-gen-ii.clamp_bottom_y":-0.235,"sig-romeo5-gen-ii.coin_slot_depth":0.03,"sig-romeo5-gen-ii.elevation_d":0.601,"sig-romeo5-gen-ii.elevation_from_rear":0.61,"sig-romeo5-gen-ii.elevation_slot_length":0.29,"sig-romeo5-gen-ii.elevation_slot_width":0.11,"sig-romeo5-gen-ii.flank_z":0.637,"sig-romeo5-gen-ii.hood_notch_depth":0.03,"sig-romeo5-gen-ii.hood_notch_length":0.17,"sig-romeo5-gen-ii.hood_notch_width":0.128,"sig-romeo5-gen-ii.jaw_inner_z":0.442,"sig-romeo5-gen-ii.jaw_length":0.714,"sig-romeo5-gen-ii.lug_depth":0.1,"sig-romeo5-gen-ii.lug_length":0.15,"sig-romeo5-gen-ii.lug_width":0.314,"sig-romeo5-gen-ii.mount_length":1.98,"sig-romeo5-gen-ii.objective_bezel_d":0.94,"sig-romeo5-gen-ii.objective_recess":0.12,"sig-romeo5-gen-ii.optical_axis_above_rail":1.41,"sig-romeo5-gen-ii.panel_from_front":0.587,"sig-romeo5-gen-ii.panel_groove":0.02,"sig-romeo5-gen-ii.panel_length":1.177,"sig-romeo5-gen-ii.panel_width":0.505,"sig-romeo5-gen-ii.screw_head_d":0.214,"sig-romeo5-gen-ii.screw_z":0.2,"sig-romeo5-gen-ii.torx_depth":0.04,"sig-romeo5-gen-ii.torx_head_d":0.231,"sig-romeo5-gen-ii.torx_star_d":0.165,"sig-romeo5-gen-ii.tube_od":1.123,"sig-romeo5-gen-ii.turret_groove":0.02,"sig-romeo5-gen-ii.web_width":0.228,"sig-romeo5-gen-ii.windage_face_z":0.827,"sig-romeo5-gen-ii.windage_slot_length":0.26,"sig-romeo5-gen-ii.windage_slot_width":0.096,"sig-romeo5-gen-ii.windage_step":0.03,"sig-romeo5-gen-ii.window_d":0.7874015748031495,"sig-romeo5-i-beam-mount.deck_above_rail":0.798,"sig-romeo5-i-beam-mount.deck_x":0,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{"side":[[-1.251,2.094],[-1.251,1.186],[-1.097,1.032],[-1.003,1.032],[-0.99,1.019],[-0.989,0.898],[-0.814,0.898],[-0.784,0.851],[-0.757,0.826],[-0.632,0.826],[-0.605,0.851],[-0.588,0.882],[-0.572,0.896],[-0.556,0.888],[-0.53,0.863],[-0.523,0.844],[-0.523,0.794],[-0.535,0.753],[-0.552,0.724],[-0.589,0.687],[-0.941,0.493],[-0.976,0.466],[-0.99,0.42],[-0.989,0],[0,0],[0.989,0],[0.99,0.432],[0.983,0.456],[0.955,0.486],[0.582,0.694],[0.552,0.727],[0.533,0.763],[0.523,0.801],[0.526,0.849],[0.533,0.866],[0.553,0.886],[0.577,0.896],[0.607,0.849],[0.635,0.826],[0.757,0.826],[0.784,0.849],[0.817,0.898],[0.989,0.898],[0.99,0.995],[0.997,1.012],[1.018,1.03],[1.161,1.032],[1.493,1.084],[1.493,2.197],[1.25,2.232],[0.929,2.289],[0.915,2.289],[0.898,2.277],[0.888,2.284],[0.773,2.304],[0.76,2.317],[0.761,2.323],[0.749,2.325],[0.608,2.342],[0.594,2.351],[0.572,2.354],[0.567,2.349],[0.484,2.363],[0.462,2.373],[0.433,2.361],[0.304,2.383],[0.223,2.397],[0.204,2.418],[0.194,2.421],[0.177,2.423],[0.172,2.418],[0.163,2.426],[0.158,2.421],[0.139,2.43],[0.132,2.426],[0.11,2.435],[0.103,2.43],[0.096,2.438],[0.089,2.433],[0.079,2.44],[0.074,2.435],[0.067,2.442],[0.053,2.445],[0.048,2.44],[0.038,2.447],[0.034,2.442],[0.026,2.45],[0.019,2.445],[0.012,2.452],[0.005,2.447],[-0.002,2.454],[-0.026,2.454],[-0.101,2.471],[-0.115,2.457],[-0.127,2.457],[-0.239,2.474],[-0.256,2.49],[-0.879,2.49],[-0.914,2.468],[-1.086,2.259]],"end":[[-0.648,0.417],[-0.648,0.02],[-0.634,0.01],[-0.589,0],[-0.341,0],[-0.34,0.016],[-0.447,0.125],[-0.447,0.142],[-0.434,0.155],[-0.412,0.158],[-0.343,0.222],[-0.169,0.222],[-0.156,0.209],[-0.156,0.14],[-0.14,0.124],[0.141,0.124],[0.155,0.137],[0.155,0.209],[0.168,0.222],[0.342,0.222],[0.439,0.128],[0.436,0.113],[0.379,0.056],[0.38,0.005],[0.39,0],[0.588,0],[0.646,0.013],[0.646,0.424],[0.447,0.48],[0.409,0.501],[0.354,0.554],[0.175,0.554],[0.139,0.563],[0.107,0.593],[0.095,0.62],[0.09,0.655],[0.095,0.765],[0.104,0.82],[0.118,0.833],[0.139,0.821],[0.256,0.821],[0.288,0.849],[0.316,0.888],[0.39,0.891],[0.396,0.897],[0.427,1.018],[0.427,1.035],[0.42,1.042],[0.434,1.056],[0.441,1.076],[0.469,1.101],[0.495,1.108],[0.831,1.103],[0.847,1.14],[0.883,1.293],[0.897,1.381],[0.911,1.541],[0.911,1.565],[0.895,1.579],[0.895,1.684],[0.911,1.699],[0.9,1.863],[0.878,1.995],[0.837,2.155],[0.824,2.163],[0.793,2.158],[0.366,2.158],[0.35,2.181],[0.292,2.478],[-0.293,2.478],[-0.366,2.124],[-0.489,2.001],[-0.636,1.957],[-0.636,1.307],[-0.501,1.27],[-0.459,1.236],[-0.445,1.2],[-0.433,1.059],[-0.418,1.045],[-0.428,1.023],[-0.395,0.897],[-0.384,0.888],[-0.315,0.888],[-0.287,0.846],[-0.257,0.821],[-0.138,0.821],[-0.119,0.836],[-0.103,0.815],[-0.091,0.739],[-0.089,0.674],[-0.094,0.627],[-0.103,0.598],[-0.14,0.563],[-0.176,0.554],[-0.312,0.554],[-0.313,0.491],[-0.326,0.478],[-0.34,0.491],[-0.342,0.538],[-0.362,0.542],[-0.403,0.506],[-0.441,0.482],[-0.63,0.43]]},"features":{"side":{"hood":[[[1.25,2.23],[1.497,2.23],[1.497,1.079],[1.25,1.079]]],"rear_bezel":[[[-1.255,2.262],[-1.092,2.262],[-1.092,1.026],[-1.255,1.026]]],"battery_cap":[[[-0.122,2.178],[0.953,2.178],[0.953,1.105],[-0.122,1.105]]],"cap_boss":[[[-0.184,2.221],[0.999,2.221],[0.999,1.062],[-0.184,1.062]]],"windage_boss":[[[-0.905,1.965],[-0.261,1.965],[-0.261,1.318],[-0.905,1.318]]],"windage_cap":[[[-0.833,1.893],[-0.33,1.893],[-0.33,1.39],[-0.833,1.39]]],"windage_dial":[[[-0.733,1.79],[-0.433,1.79],[-0.433,1.491],[-0.733,1.491]]],"skirt":[[[-0.994,1.251],[0.994,1.251],[0.994,1.033],[-0.994,1.033]]],"plate":[[[-0.994,1.033],[0.994,1.033],[0.994,0.894],[-0.994,0.894]]],"web":[[[-0.527,0.894],[0.532,0.894],[0.532,0.66],[-0.527,0.66]]],"base":[[[-0.994,0.669],[0.994,0.669],[0.994,-0.004],[-0.994,-0.004]]],"torx_head":[[[-0.141,0.365],[0.148,0.365],[0.148,0.075],[-0.141,0.075]]],"bolt_boss":[[[-0.326,0.54],[0.33,0.54],[0.33,-0.116],[-0.326,-0.116]]],"screw_rear":[[[-0.802,0.894],[-0.582,0.894],[-0.582,0.825],[-0.802,0.825]]],"screw_front":[[[0.587,0.894],[0.805,0.894],[0.805,0.825],[0.587,0.825]]],"rear_button":[[[-0.108,2.472],[0.213,2.472],[0.213,2.396],[-0.108,2.396]]],"front_button":[[[0.45,2.381],[0.769,2.381],[0.769,2.305],[0.45,2.305]]]},"end":{"battery_cap":[[[0.915,2.167],[0.796,2.167],[0.796,1.104],[0.915,1.104]]],"objective":[[[0.409,2.038],[-0.408,2.038],[-0.408,1.221],[0.409,1.221]]],"web":[[[0.115,0.806],[-0.114,0.806],[-0.114,0.732],[0.115,0.732]]],"screw_right":[[[0.309,0.885],[0.094,0.885],[0.094,0.82],[0.309,0.82]]],"screw_left":[[[-0.093,0.885],[-0.307,0.885],[-0.307,0.82],[-0.093,0.82]]],"buttons":[[[0.122,2.458],[-0.128,2.458],[-0.128,2.386],[0.122,2.386]]],"lug":[[[0.158,0.218],[-0.157,0.218],[-0.157,0.118],[0.158,0.118]]],"jaw":[[[-0.443,0.548],[-0.651,0.548],[-0.651,-0.004],[-0.443,-0.004]]],"channel_roof":[[[0.352,0.223],[-0.35,0.223],[-0.35,0.214],[0.352,0.214]]]}},"placement":{"side":{"plane":"xy","offset":{"y":"clamp_bottom_y"}},"end":{"plane":"zy","offset":{"y":"clamp_bottom_y"}}},"bounds":{"min":[-1.255,0,-0.636],"max":[1.4924,1.457,0.909]},"axis_y":0.612,"volume_in3":3.9694,"centroid":[0.0836,0.644,0.0567],"shell":[0.1236,0.6866,0.1104],"area_in2":27.7175,"triangles":29176,"manifold":true,"slabs":[[-1.255,0,-0.636,-0.863,1.457,0.767],[-0.863,0,-0.636,-0.078,1.457,0.852],[-0.078,0,-0.636,0.315,1.434,0.906],[0.315,0,-0.636,1.1,1.348,0.909],[1.1,0,-0.636,1.492,1.226,0.636]],"slots":["body","ends","knobs","controls","lens"]},"sig-romeo5-i-beam-mount":{"part":"sig-romeo5-i-beam-mount","model":"sig-romeo5-i-beam-mount.glb","script":"sig_romeo5_gen_ii.py","inputs":{"sig-romeo5-gen-ii.base_left_z":0.649,"sig-romeo5-gen-ii.bolt_counterbore":0.05,"sig-romeo5-gen-ii.bolt_end_d":0.197,"sig-romeo5-gen-ii.bolt_end_proud":0.015,"sig-romeo5-gen-ii.button_width":0.25,"sig-romeo5-gen-ii.cap_edge_z":0.841,"sig-romeo5-gen-ii.cap_face_z":0.91,"sig-romeo5-gen-ii.cap_rim_z":0.791,"sig-romeo5-gen-ii.cap_slot_length":0.497,"sig-romeo5-gen-ii.cap_slot_width":0.127,"sig-romeo5-gen-ii.clamp_bottom_y":-0.235,"sig-romeo5-gen-ii.coin_slot_depth":0.03,"sig-romeo5-gen-ii.elevation_d":0.601,"sig-romeo5-gen-ii.elevation_from_rear":0.61,"sig-romeo5-gen-ii.elevation_slot_length":0.29,"sig-romeo5-gen-ii.elevation_slot_width":0.11,"sig-romeo5-gen-ii.flank_z":0.637,"sig-romeo5-gen-ii.hood_notch_depth":0.03,"sig-romeo5-gen-ii.hood_notch_length":0.17,"sig-romeo5-gen-ii.hood_notch_width":0.128,"sig-romeo5-gen-ii.jaw_inner_z":0.442,"sig-romeo5-gen-ii.jaw_length":0.714,"sig-romeo5-gen-ii.lug_depth":0.1,"sig-romeo5-gen-ii.lug_length":0.15,"sig-romeo5-gen-ii.lug_width":0.314,"sig-romeo5-gen-ii.mount_length":1.98,"sig-romeo5-gen-ii.objective_bezel_d":0.94,"sig-romeo5-gen-ii.objective_recess":0.12,"sig-romeo5-gen-ii.optical_axis_above_rail":1.41,"sig-romeo5-gen-ii.panel_from_front":0.587,"sig-romeo5-gen-ii.panel_groove":0.02,"sig-romeo5-gen-ii.panel_length":1.177,"sig-romeo5-gen-ii.panel_width":0.505,"sig-romeo5-gen-ii.screw_head_d":0.214,"sig-romeo5-gen-ii.screw_z":0.2,"sig-romeo5-gen-ii.torx_depth":0.04,"sig-romeo5-gen-ii.torx_head_d":0.231,"sig-romeo5-gen-ii.torx_star_d":0.165,"sig-romeo5-gen-ii.tube_od":1.123,"sig-romeo5-gen-ii.turret_groove":0.02,"sig-romeo5-gen-ii.web_width":0.228,"sig-romeo5-gen-ii.windage_face_z":0.827,"sig-romeo5-gen-ii.windage_slot_length":0.26,"sig-romeo5-gen-ii.windage_slot_width":0.096,"sig-romeo5-gen-ii.windage_step":0.03,"sig-romeo5-gen-ii.window_d":0.7874015748031495,"sig-romeo5-i-beam-mount.deck_above_rail":0.798,"sig-romeo5-i-beam-mount.deck_x":0,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835},"profiles":{},"features":{},"placement":{},"bounds":{"min":[-1.098,-0.235,-0.664],"max":[1.1674,0.798,0.646]},"volume_in3":1.2928,"centroid":[0.0007,0.2347,-0.0009],"shell":[0.0084,0.2709,-0.0319],"area_in2":15.5406,"triangles":6376,"manifold":true,"rail_seat":{"x":[-0.99,0.99],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-1.098,-0.235,-0.664,1.167,0.798,0.646]],"slots":["mount","hardware"]},"sig-tango-msr-1-6x24":{"part":"sig-tango-msr-1-6x24","model":"sig-tango-msr-1-6x24.glb","script":"sig_tango_msr_1_6x24.py","inputs":{"sig-alpha-msr-30mm.ring_od":1.363,"sig-tango-msr-1-6x24.cap_flat_width":0.233,"sig-tango-msr-1-6x24.cap_flats":6,"sig-tango-msr-1-6x24.cap_knurl_columns":2,"sig-tango-msr-1-6x24.cap_knurl_depth":0.0125,"sig-tango-msr-1-6x24.cap_knurl_pitch":0.04,"sig-tango-msr-1-6x24.cap_knurl_rows":4,"sig-tango-msr-1-6x24.cap_rib_width":0.08,"sig-tango-msr-1-6x24.elevation_cap_turned":9.5,"sig-tango-msr-1-6x24.elevation_top_above_axis":1.164,"sig-tango-msr-1-6x24.eyepiece_lens_d":1.22,"sig-tango-msr-1-6x24.eyepiece_lens_recess":0.3,"sig-tango-msr-1-6x24.eyepiece_rear_behind_bolt":3.392,"sig-tango-msr-1-6x24.eyepiece_rim_id":1.48,"sig-tango-msr-1-6x24.illumination_detent_d":1.11,"sig-tango-msr-1-6x24.illumination_detent_outer":1.11,"sig-tango-msr-1-6x24.illumination_dial_d":1.2,"sig-tango-msr-1-6x24.illumination_dial_outer":0.95,"sig-tango-msr-1-6x24.illumination_face_d":0.95,"sig-tango-msr-1-6x24.illumination_knob_turned":32,"sig-tango-msr-1-6x24.illumination_knurl_columns":4,"sig-tango-msr-1-6x24.illumination_knurl_inner":1.17,"sig-tango-msr-1-6x24.illumination_knurl_land_width":0.1,"sig-tango-msr-1-6x24.illumination_knurl_outer":1.28,"sig-tango-msr-1-6x24.illumination_knurl_patches":12,"sig-tango-msr-1-6x24.illumination_knurl_rows":3,"sig-tango-msr-1-6x24.illumination_reach":1.43,"sig-tango-msr-1-6x24.illumination_ring_d":1.17,"sig-tango-msr-1-6x24.magnification_ring_knurl_depth":0.017,"sig-tango-msr-1-6x24.magnification_ring_knurl_groove_width":0.09,"sig-tango-msr-1-6x24.magnification_ring_knurl_length":1.04,"sig-tango-msr-1-6x24.magnification_ring_knurl_panel_width":27,"sig-tango-msr-1-6x24.magnification_ring_knurl_panels":6,"sig-tango-msr-1-6x24.magnification_ring_knurl_rows":3,"sig-tango-msr-1-6x24.objective_bore_d":1.01,"sig-tango-msr-1-6x24.objective_front_x":7.008,"sig-tango-msr-1-6x24.objective_lens_d":0.9448818897637795,"sig-tango-msr-1-6x24.objective_lens_recess":0.47,"sig-tango-msr-1-6x24.saddle_flat_bottom":0.82,"sig-tango-msr-1-6x24.saddle_flat_left":0.8,"sig-tango-msr-1-6x24.saddle_flat_right":0.77,"sig-tango-msr-1-6x24.saddle_flat_top":0.78,"sig-tango-msr-1-6x24.saddle_radius":0.985,"sig-tango-msr-1-6x24.tube_od":1.1811023622047243,"sig-tango-msr-1-6x24.windage_cap_turned":48.75,"sig-tango-msr-1-6x24.windage_reach":1.165},"profiles":{"body":[[-3.447,0.227],[-3.447,-0.226],[-3.443,-0.23],[-3.434,-0.522],[-3.417,-0.734],[-3.392,-0.882],[-3.373,-0.901],[-3.318,-0.914],[-3.131,-0.916],[-3.064,-0.908],[-2.992,-0.912],[-2.958,-0.904],[-2.945,-0.913],[-2.928,-0.904],[-2.911,-0.913],[-2.779,-0.909],[-2.775,-0.914],[-2.648,-0.914],[-2.644,-0.91],[-2.474,-0.911],[-2.469,-0.886],[-2.461,-0.886],[-2.448,-0.899],[-2.431,-0.899],[-2.423,-0.89],[-2.414,-0.907],[-2.393,-0.908],[-2.372,-0.886],[-2.363,-0.886],[-2.346,-0.912],[-2.235,-0.904],[-2.206,-0.909],[-2.201,-0.887],[-2.195,-0.89],[-2.195,-0.902],[-2.189,-0.909],[-1.413,-0.909],[-1.408,-0.905],[-1.263,-0.902],[-1.216,-0.911],[-1.173,-0.949],[-1.147,-0.932],[-1.13,-0.932],[-1.105,-0.945],[-1.088,-0.933],[-1.066,-0.933],[-1.045,-0.946],[-1.019,-0.929],[-0.989,-0.946],[-0.959,-0.929],[-0.929,-0.946],[-0.904,-0.93],[-0.869,-0.947],[-0.861,-0.947],[-0.839,-0.93],[-0.831,-0.93],[-0.809,-0.947],[-0.779,-0.93],[-0.745,-0.948],[-0.724,-0.931],[-0.711,-0.931],[-0.685,-0.948],[-0.664,-0.931],[-0.651,-0.931],[-0.634,-0.944],[-0.616,-0.944],[-0.599,-0.932],[-0.586,-0.932],[-0.573,-0.944],[-0.556,-0.945],[-0.535,-0.928],[-0.513,-0.945],[-0.47,-0.932],[-0.453,-0.945],[-0.44,-0.945],[-0.419,-0.928],[-0.393,-0.946],[-0.372,-0.942],[-0.359,-0.929],[-0.333,-0.946],[-0.312,-0.942],[-0.299,-0.929],[-0.29,-0.929],[-0.269,-0.946],[-0.26,-0.946],[-0.239,-0.93],[-0.209,-0.947],[-0.2,-0.947],[-0.178,-0.93],[-0.153,-0.939],[-0.045,-0.833],[-0.022,-0.818],[-0.004,-0.792],[0.06,-0.733],[0.069,-0.716],[0.166,-0.621],[0.204,-0.591],[1.128,-0.587],[1.134,-0.598],[1.134,-0.641],[1.143,-0.658],[1.175,-0.686],[1.401,-0.679],[1.505,-0.688],[1.522,-0.679],[1.561,-0.684],[1.578,-0.676],[1.773,-0.681],[1.799,-0.668],[1.819,-0.649],[1.823,-0.606],[1.843,-0.587],[1.847,-0.591],[2.103,-0.593],[2.108,-0.588],[2.377,-0.59],[2.406,-0.609],[2.456,-0.668],[2.466,-0.666],[2.469,-0.646],[2.482,-0.651],[2.493,-0.67],[2.493,-0.704],[2.534,-0.745],[2.547,-0.754],[2.586,-0.758],[2.593,-0.774],[2.604,-0.78],[2.765,-0.802],[2.843,-0.803],[2.913,-0.812],[3.271,-0.818],[3.284,-0.814],[3.302,-0.819],[3.306,-0.814],[3.485,-0.815],[3.555,-0.807],[3.625,-0.808],[3.735,-0.791],[3.746,-0.785],[3.746,-0.755],[3.752,-0.748],[3.8,-0.744],[3.822,-0.731],[3.958,-0.59],[4.257,-0.587],[4.267,-0.598],[4.281,-0.654],[4.309,-0.682],[4.344,-0.687],[4.349,-0.683],[4.498,-0.683],[4.502,-0.679],[4.771,-0.685],[4.775,-0.681],[4.964,-0.682],[4.991,-0.673],[5.015,-0.65],[5.033,-0.594],[5.053,-0.587],[6.707,-0.592],[6.712,-0.588],[6.92,-0.593],[6.938,-0.584],[7.036,-0.568],[7.074,-0.535],[7.096,-0.501],[7.105,-0.462],[7.118,-0.44],[7.132,-0.392],[7.132,-0.366],[7.145,-0.327],[7.145,-0.297],[7.154,-0.262],[7.158,-0.102],[7.167,-0.093],[7.172,0.028],[7.167,0.033],[7.167,0.093],[7.158,0.102],[7.154,0.263],[7.145,0.297],[7.145,0.328],[7.118,0.441],[7.105,0.462],[7.096,0.502],[7.074,0.536],[7.036,0.569],[6.934,0.591],[6.929,0.587],[6.92,0.591],[6.872,0.587],[6.392,0.592],[6.388,0.588],[5.053,0.587],[5.033,0.594],[5.015,0.65],[4.991,0.674],[4.964,0.682],[4.502,0.679],[4.498,0.683],[4.322,0.688],[4.309,0.684],[4.281,0.656],[4.267,0.6],[4.257,0.589],[3.958,0.59],[3.822,0.732],[3.8,0.745],[3.752,0.75],[3.746,0.756],[3.746,0.786],[3.735,0.793],[3.485,0.815],[3.171,0.82],[3.118,0.811],[2.913,0.812],[2.843,0.803],[2.765,0.804],[2.695,0.791],[2.652,0.791],[2.625,0.778],[2.604,0.778],[2.593,0.772],[2.586,0.757],[2.547,0.753],[2.534,0.744],[2.493,0.703],[2.493,0.669],[2.482,0.65],[2.469,0.645],[2.466,0.665],[2.456,0.667],[2.406,0.609],[2.377,0.59],[1.847,0.591],[1.843,0.587],[1.823,0.606],[1.819,0.649],[1.799,0.669],[1.773,0.681],[1.522,0.678],[1.496,0.686],[1.492,0.682],[1.327,0.678],[1.323,0.683],[1.175,0.687],[1.143,0.659],[1.134,0.642],[1.134,0.6],[1.128,0.589],[0.523,0.591],[0.519,0.586],[0.506,0.591],[0.204,0.591],[0.166,0.621],[0.069,0.718],[0.06,0.735],[-0.153,0.938],[-0.178,0.929],[-0.2,0.946],[-0.209,0.946],[-0.239,0.929],[-0.26,0.946],[-0.269,0.946],[-0.29,0.929],[-0.299,0.929],[-0.312,0.942],[-0.333,0.947],[-0.359,0.93],[-0.372,0.942],[-0.393,0.947],[-0.419,0.93],[-0.44,0.947],[-0.453,0.947],[-0.47,0.934],[-0.513,0.947],[-0.535,0.926],[-0.556,0.943],[-0.573,0.943],[-0.586,0.93],[-0.599,0.93],[-0.616,0.943],[-0.634,0.943],[-0.651,0.93],[-0.664,0.93],[-0.685,0.947],[-0.711,0.93],[-0.724,0.93],[-0.745,0.947],[-0.779,0.93],[-0.809,0.947],[-0.831,0.93],[-0.839,0.93],[-0.861,0.948],[-0.869,0.948],[-0.904,0.931],[-0.929,0.948],[-0.959,0.931],[-0.989,0.948],[-1.019,0.931],[-1.049,0.948],[-1.066,0.931],[-1.088,0.931],[-1.105,0.944],[-1.13,0.931],[-1.147,0.931],[-1.173,0.948],[-1.216,0.91],[-1.263,0.901],[-1.408,0.906],[-1.413,0.91],[-1.571,0.911],[-1.575,0.906],[-2.091,0.912],[-2.095,0.907],[-2.189,0.907],[-2.197,0.886],[-2.204,0.888],[-2.206,0.907],[-2.235,0.903],[-2.316,0.912],[-2.346,0.912],[-2.363,0.887],[-2.372,0.887],[-2.393,0.908],[-2.414,0.908],[-2.423,0.891],[-2.431,0.899],[-2.448,0.899],[-2.461,0.887],[-2.469,0.887],[-2.474,0.912],[-2.61,0.912],[-2.614,0.908],[-2.911,0.913],[-2.928,0.905],[-2.945,0.913],[-2.953,0.905],[-2.992,0.913],[-3.021,0.909],[-3.318,0.914],[-3.373,0.901],[-3.392,0.882],[-3.413,0.772],[-3.434,0.523],[-3.443,0.231]],"turret":[[2.545,1.038],[2.545,1.012],[2.554,1.008],[2.554,0.999],[2.545,0.995],[2.545,0.974],[2.554,0.969],[2.554,0.961],[2.545,0.956],[2.545,0.935],[2.554,0.922],[2.545,0.914],[2.545,0.892],[2.593,0.836],[2.593,0.785],[2.599,0.782],[2.625,0.787],[2.652,0.8],[2.695,0.799],[2.765,0.812],[2.843,0.812],[2.913,0.82],[3.118,0.82],[3.171,0.829],[3.485,0.824],[3.555,0.815],[3.625,0.815],[3.691,0.802],[3.717,0.806],[3.743,0.797],[3.746,0.838],[3.798,0.894],[3.798,0.907],[3.781,0.92],[3.798,0.937],[3.785,0.963],[3.798,0.976],[3.798,0.984],[3.785,1.002],[3.803,1.019],[3.781,1.053],[3.748,1.086],[3.608,1.15],[3.332,1.159],[3.328,1.164],[3.319,1.159],[3.302,1.164],[3,1.164],[2.996,1.16],[2.739,1.156],[2.595,1.092],[2.575,1.077]],"lever":[[-0.953,1.077],[-0.953,0.946],[-0.946,0.943],[-0.925,0.956],[-0.904,0.939],[-0.895,0.939],[-0.861,0.956],[-0.848,0.943],[-0.831,0.939],[-0.805,0.956],[-0.771,0.939],[-0.745,0.956],[-0.724,0.939],[-0.711,0.939],[-0.685,0.956],[-0.664,0.939],[-0.651,0.939],[-0.634,0.951],[-0.616,0.951],[-0.599,0.939],[-0.586,0.938],[-0.573,0.951],[-0.556,0.951],[-0.543,0.938],[-0.535,0.938],[-0.513,0.955],[-0.47,0.943],[-0.453,0.955],[-0.44,0.955],[-0.415,0.938],[-0.393,0.955],[-0.38,0.955],[-0.355,0.938],[-0.333,0.955],[-0.32,0.955],[-0.299,0.938],[-0.29,0.938],[-0.277,0.951],[-0.26,0.955],[-0.234,0.938],[-0.219,0.948],[-0.219,1.004],[-0.286,1.07],[-0.303,1.079],[-0.578,1.079],[-0.584,1.085],[-0.588,1.192],[-0.55,1.235],[-0.554,1.303],[-0.533,1.324],[-0.546,1.35],[-0.533,1.362],[-0.533,1.375],[-0.546,1.392],[-0.533,1.405],[-0.533,1.413],[-0.546,1.43],[-0.533,1.443],[-0.533,1.452],[-0.546,1.465],[-0.546,1.473],[-0.533,1.482],[-0.533,1.49],[-0.546,1.507],[-0.533,1.52],[-0.533,1.533],[-0.546,1.55],[-0.533,1.563],[-0.533,1.571],[-0.546,1.584],[-0.546,1.592],[-0.537,1.597],[-0.533,1.609],[-0.546,1.622],[-0.546,1.631],[-0.533,1.639],[-0.533,1.652],[-0.546,1.665],[-0.546,1.673],[-0.533,1.682],[-0.533,1.69],[-0.546,1.707],[-0.533,1.72],[-0.533,1.729],[-0.546,1.742],[-0.546,1.75],[-0.533,1.767],[-0.546,1.78],[-0.537,1.805],[-0.554,1.822],[-0.554,1.844],[-0.565,1.859],[-0.586,1.867],[-0.852,1.867],[-0.871,1.844],[-0.871,1.827],[-0.884,1.814],[-0.88,1.784],[-0.889,1.763],[-0.88,1.741],[-0.889,1.733],[-0.889,1.72],[-0.88,1.703],[-0.889,1.682],[-0.876,1.665],[-0.889,1.652],[-0.889,1.644],[-0.876,1.631],[-0.876,1.622],[-0.884,1.618],[-0.889,1.605],[-0.876,1.584],[-0.889,1.567],[-0.876,1.55],[-0.884,1.537],[-0.884,1.52],[-0.876,1.503],[-0.884,1.495],[-0.884,1.482],[-0.871,1.469],[-0.889,1.448],[-0.876,1.431],[-0.876,1.422],[-0.884,1.418],[-0.884,1.401],[-0.871,1.388],[-0.884,1.375],[-0.884,1.363],[-0.871,1.35],[-0.884,1.329],[-0.867,1.307],[-0.867,1.235],[-0.829,1.188],[-0.833,1.167],[-0.829,1.162],[-0.829,1.086],[-0.835,1.079]]},"features":{"body":{},"turret":{},"lever":{}},"placement":{"body":{"plane":"xy","offset":{}},"turret":{"plane":"xy","offset":{}},"lever":{"plane":"xy","offset":{}}},"bounds":{"min":[-3.392,-0.948,-1.43],"max":[7.008,1.8647,1.165]},"volume_in3":19.0403,"centroid":[1.0755,0.0258,-0.0166],"shell":[1.389,0.0533,-0.0248],"area_in2":67.9696,"triangles":73248,"manifold":true,"slabs":[[-3.392,-0.948,-0.948,-0.992,0.948,0.948],[-0.992,-0.948,-0.947,-0.192,1.865,0.947],[-0.192,-0.948,-0.947,0.208,0.948,0.947],[0.208,-0.591,-0.591,2.208,0.591,0.591],[2.208,-0.806,-1.41,2.608,1.091,1.092],[2.608,-0.82,-1.43,3.808,1.164,1.165],[3.808,-0.753,-0.753,4.208,0.753,0.753],[4.208,-0.591,-0.591,7.008,0.591,0.591]],"slots":["body","lens"]},"silencerco-sparrow-22":{"part":"silencerco-sparrow-22","model":"silencerco-sparrow-22.glb","script":"silencerco_sparrow_22.py","inputs":{"silencerco-sparrow-22.bore_d":0.27,"silencerco-sparrow-22.front_cap_seam_behind_face":0.07,"silencerco-sparrow-22.half_length":2.54,"silencerco-sparrow-22.notch_floor_across":0.712,"silencerco-sparrow-22.notch_length":0.25,"silencerco-sparrow-22.notch_width":0.097,"silencerco-sparrow-22.notches":8,"silencerco-sparrow-22.od":1.06,"silencerco-sparrow-22.overall_length":5.08,"silencerco-sparrow-22.rear_break_x":0.149,"silencerco-sparrow-22.rear_cap_seam_x":0.445,"silencerco-sparrow-22.rear_chamfer_d":1.006,"silencerco-sparrow-22.rear_chamfer_x":0.07,"silencerco-sparrow-22.rear_face_d":0.852},"profiles":{"side":[[-2.54,-0.338],[-2.532,-0.343],[-2.535,-0.392],[-2.529,-0.403],[-2.447,-0.492],[-2.353,-0.522],[-0.904,-0.53],[2.429,-0.53],[2.512,-0.522],[2.524,-0.51],[2.54,-0.472],[2.54,0.464],[2.532,0.494],[2.512,0.522],[2.442,0.527],[-0.217,0.53],[-2.356,0.522],[-2.429,0.503],[-2.527,0.403],[-2.54,0.373]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"x":"half_length"}}},"bounds":{"min":[0,-0.53,-0.53],"max":[5.08,0.53,0.53]},"volume_in3":4.27,"centroid":[2.5202,0,0],"shell":[2.6617,0,0],"area_in2":23.9517,"triangles":12240,"manifold":true,"slabs":[[0,-0.53,-0.53,5.08,0.53,0.53]],"slots":["body","caps"]},"slr-sentry-7-gas-block":{"part":"slr-sentry-7-gas-block","model":"slr-sentry-7-gas-block.glb","script":"slr_sentry_7_gas_block.py","inputs":{"slr-sentry-7-gas-block.adjuster_above_bore":0.481,"slr-sentry-7-gas-block.adjuster_end_d":0.14,"slr-sentry-7-gas-block.adjuster_head_d":0.18,"slr-sentry-7-gas-block.adjuster_reach":0.17,"slr-sentry-7-gas-block.adjuster_socket":0.067,"slr-sentry-7-gas-block.edge_break":0.008,"slr-sentry-7-gas-block.flute_bottom_below_bore":0.38,"slr-sentry-7-gas-block.flute_depth":0.035,"slr-sentry-7-gas-block.flute_front_from_front":0.154,"slr-sentry-7-gas-block.flute_pitch":0.227,"slr-sentry-7-gas-block.flute_top_above_bore":0.255,"slr-sentry-7-gas-block.flute_width":0.106,"slr-sentry-7-gas-block.foot_below_bore":0.548,"slr-sentry-7-gas-block.height_above_bore":0.812,"slr-sentry-7-gas-block.journal_id":0.75,"slr-sentry-7-gas-block.length":0.856,"slr-sentry-7-gas-block.pin_hole_above_bore":0.674,"slr-sentry-7-gas-block.pin_hole_d":0.078,"slr-sentry-7-gas-block.pin_hole_from_front":0.262,"slr-sentry-7-gas-block.pin_to_port":0.418,"slr-sentry-7-gas-block.port_from_rear":0.176,"slr-sentry-7-gas-block.set_screw_d":0.147,"slr-sentry-7-gas-block.set_screw_front_from_front":0.252,"slr-sentry-7-gas-block.set_screw_length":0.15,"slr-sentry-7-gas-block.set_screw_spacing":0.4,"slr-sentry-7-gas-block.spring_above_bore":0.515,"slr-sentry-7-gas-block.spring_flat_margin":0.012,"slr-sentry-7-gas-block.spring_front_from_front":0.094,"slr-sentry-7-gas-block.spring_height_front":0.115,"slr-sentry-7-gas-block.spring_height_rear":0.198,"slr-sentry-7-gas-block.spring_rear_from_front":0.771,"slr-sentry-7-gas-block.spring_screw_head_d":0.12,"slr-sentry-7-gas-block.spring_thickness":0.025,"slr-sentry-7-gas-block.tube_hole_above_bore":0.674,"slr-sentry-7-gas-block.tube_hole_d":0.1805,"slr-sentry-7-gas-block.tube_hole_past_pin":0.217,"slr-sentry-7-gas-block.width":0.899},"profiles":{"front":[[-0.452,0.016],[-0.452,0.005],[-0.448,0],[-0.445,-0.06],[-0.431,-0.126],[-0.409,-0.185],[-0.381,-0.237],[-0.346,-0.287],[-0.313,-0.323],[-0.279,-0.352],[-0.233,-0.385],[-0.201,-0.415],[-0.173,-0.452],[-0.124,-0.54],[-0.111,-0.548],[0.108,-0.548],[0.122,-0.541],[0.172,-0.452],[0.192,-0.424],[0.23,-0.386],[0.27,-0.358],[0.307,-0.328],[0.348,-0.284],[0.379,-0.24],[0.405,-0.193],[0.428,-0.133],[0.441,-0.082],[0.447,-0.032],[0.445,0.05],[0.439,0.09],[0.425,0.142],[0.408,0.185],[0.374,0.247],[0.344,0.287],[0.34,0.296],[0.337,0.297],[0.305,0.329],[0.29,0.347],[0.266,0.383],[0.259,0.398],[0.259,0.407],[0.251,0.415],[0.239,0.452],[0.239,0.557],[0.226,0.558],[0.216,0.566],[0.183,0.6],[0.174,0.614],[0.166,0.63],[0.158,0.657],[0.157,0.705],[0.154,0.717],[0.145,0.739],[0.132,0.756],[0.107,0.778],[0.071,0.798],[0.036,0.809],[0.014,0.812],[-0.037,0.809],[-0.075,0.797],[-0.115,0.772],[-0.132,0.758],[-0.147,0.736],[-0.158,0.704],[-0.158,0.579],[-0.161,0.546],[-0.179,0.48],[-0.201,0.437],[-0.229,0.398],[-0.341,0.293],[-0.389,0.224],[-0.412,0.178],[-0.429,0.131],[-0.443,0.07],[-0.448,0.02]]},"features":{"front":{}},"placement":{"front":{"plane":"zy","offset":{}}},"bounds":{"min":[-0.176,-0.548,-0.4484],"max":[0.85,0.812,0.4486]},"volume_in3":0.2788,"centroid":[0.2578,0.154,0.0117],"shell":[0.2601,0.118,0.0136],"area_in2":7.2046,"triangles":17036,"manifold":true,"slabs":[[-0.176,-0.548,-0.397,0.68,-0.208,0.397],[-0.176,-0.208,-0.448,0.68,0.132,0.449],[-0.176,0.132,-0.429,0.85,0.472,0.429],[-0.176,0.472,-0.183,0.85,0.812,0.294]],"slots":["body","hardware","spring"]},"spikes-tactical-sdr100a":{"part":"spikes-tactical-sdr100a","model":"spikes-tactical-sdr100a.glb","script":"spikes_tactical_sdr100a.py","inputs":{"bcm-m4-upper.thread_pitch":0.0556,"spikes-tactical-sdr100a.flange_diameter":1.56,"spikes-tactical-sdr100a.length":0.85,"spikes-tactical-sdr100a.notches":20,"spikes-tactical-sdr100a.ring_lands":7,"spikes-tactical-sdr100a.ring_outside_diameter":2.1,"std.ar15.barrel_nut_body_od":1.367,"std.ar15.barrel_nut_bore_d":1.01,"std.ar15.barrel_nut_counterbore_d":1.25,"std.ar15.barrel_nut_flange_chamfer":0.03,"std.ar15.barrel_nut_flange_od":1.56,"std.ar15.barrel_nut_flange_rear":0.73,"std.ar15.barrel_nut_front_recess":0.2,"std.ar15.barrel_nut_groove":0.126,"std.ar15.barrel_nut_groove_d":1.333,"std.ar15.barrel_nut_groove_width":0.045,"std.ar15.barrel_nut_inner_chamfer":0.03,"std.ar15.barrel_nut_length":0.85,"std.ar15.barrel_nut_notch_d":0.186,"std.ar15.barrel_nut_notch_pcd":1.561,"std.ar15.barrel_nut_notches":20,"std.ar15.barrel_nut_rear_chamfer":0.015,"std.ar15.barrel_nut_rear_x":-0.394,"std.ar15.barrel_nut_recess_round":0.06,"std.ar15.barrel_nut_shoulder":0.525,"std.ar15.barrel_nut_thread_chamfer":0.04,"std.ar15.barrel_nut_thread_length":0.394,"std.ar15.barrel_nut_thread_major_d":1.244,"std.ar15.barrel_nut_thread_minor_d":1.19,"std.ar15.slip_ring_bore_d":1.75,"std.ar15.slip_ring_bore_depth":0.42,"std.ar15.slip_ring_chamfer":0.02,"std.ar15.slip_ring_front_od":1.92,"std.ar15.slip_ring_land":0.086,"std.ar15.slip_ring_length":0.6,"std.ar15.slip_ring_lip_hole_d":1.38,"std.ar15.slip_ring_notch_reach":0.875,"std.ar15.slip_ring_notch_width":0.203,"std.ar15.slip_ring_od":2.1,"std.ar15.slip_ring_rear_x":-0.144,"std.ar15.slip_ring_retainer_back_start":127.6,"std.ar15.slip_ring_retainer_gap":0.2,"std.ar15.slip_ring_retainer_hole_apart":0.457,"std.ar15.slip_ring_retainer_hole_d":0.1,"std.ar15.slip_ring_retainer_hole_pcd":1.521,"std.ar15.slip_ring_retainer_id":1.372,"std.ar15.slip_ring_retainer_lug_end":42,"std.ar15.slip_ring_retainer_od":1.671,"std.ar15.slip_ring_retainer_waist_at":73.4,"std.ar15.slip_ring_retainer_waist_d":1.503,"std.ar15.slip_ring_skirt_d":1.75,"std.ar15.slip_ring_skirt_length":0.12,"std.ar15.slip_ring_spring_gap":0.245,"std.ar15.slip_ring_spring_height":0.552,"std.ar15.slip_ring_spring_id":1.41,"std.ar15.slip_ring_spring_od":1.73,"std.ar15.slip_ring_spring_sections":4,"std.ar15.slip_ring_spring_strip":0.02,"std.ar15.slip_ring_spring_wave":0.138,"std.ar15.slip_ring_step":0.015,"std.ar15.slip_ring_steps":6},"profiles":{},"bounds":{"min":[-0.394,-1.05,-1.05],"max":[0.456,1.05,1.05]},"volume_in3":0.9056,"centroid":[0.0928,-0.0069,0],"shell":[0.0668,-0.0125,0],"area_in2":28.6246,"triangles":41844,"manifold":true,"slabs":[[-0.268,-1.05,-0.782,0.456,-0.7,0.782],[-0.394,-0.7,-0.99,0.456,-0.35,0.99],[-0.394,-0.35,-1.05,0.456,0.35,1.05],[-0.394,0.35,-0.99,0.456,0.7,0.99],[-0.268,0.7,-0.782,0.456,1.05,0.782]],"slots":["nut","ring","spring"]},"streamlight-protac-rail-mount-hl-x.body":{"part":"streamlight-protac-rail-mount-hl-x","component":"body","model":"streamlight-protac-rail-mount-hl-x.body.glb","script":"streamlight_protac_rail_mount_hl_x.py","inputs":{"std.picatinny.top_width":0.835,"streamlight-protac-rail-mount-hl-x.axis_above_mount":0.773,"streamlight-protac-rail-mount-hl-x.band_diameter":0.933,"streamlight-protac-rail-mount-hl-x.band_front_x":0.605,"streamlight-protac-rail-mount-hl-x.band_length":0.33,"streamlight-protac-rail-mount-hl-x.band_rear_x":0.622,"streamlight-protac-rail-mount-hl-x.front_x":2.946,"streamlight-protac-rail-mount-hl-x.head_diameter":1.424,"streamlight-protac-rail-mount-hl-x.lens_diameter":1.05,"streamlight-protac-rail-mount-hl-x.rear_x":2.483,"streamlight-protac-rail-mount-hl-x.waist_diameter":0.852},"profiles":{"body":[[-2.483,0.239],[-2.483,-0.239],[-2.457,-0.265],[-2.451,-0.285],[-2.449,-0.331],[-2.443,-0.348],[-2.441,-0.467],[-2.137,-0.466],[-2.074,-0.501],[-2.045,-0.506],[-1.37,-0.505],[-1.341,-0.493],[-1.183,-0.493],[-1.175,-0.488],[-1.162,-0.461],[-0.668,-0.459],[-0.616,-0.468],[-0.561,-0.468],[-0.554,-0.521],[-0.544,-0.534],[-0.532,-0.54],[-0.463,-0.545],[-0.397,-0.542],[-0.374,-0.536],[-0.357,-0.522],[-0.351,-0.522],[-0.302,-0.528],[-0.289,-0.538],[-0.288,-0.545],[-0.273,-0.55],[0.248,-0.549],[0.268,-0.529],[0.314,-0.523],[0.328,-0.523],[0.348,-0.537],[0.383,-0.546],[0.478,-0.546],[0.515,-0.537],[0.526,-0.527],[0.531,-0.512],[0.531,-0.472],[0.536,-0.468],[0.582,-0.467],[0.613,-0.459],[0.818,-0.461],[0.825,-0.497],[0.835,-0.507],[0.864,-0.521],[1.146,-0.524],[1.314,-0.621],[1.34,-0.63],[1.501,-0.632],[1.539,-0.658],[1.743,-0.675],[1.807,-0.677],[1.827,-0.666],[1.864,-0.666],[1.874,-0.679],[1.88,-0.704],[1.905,-0.712],[1.936,-0.712],[1.947,-0.704],[1.965,-0.668],[1.994,-0.668],[2.017,-0.711],[2.069,-0.711],[2.094,-0.681],[2.098,-0.668],[2.124,-0.668],[2.14,-0.704],[2.156,-0.714],[2.205,-0.711],[2.231,-0.668],[2.254,-0.667],[2.27,-0.703],[2.283,-0.714],[2.335,-0.71],[2.353,-0.689],[2.363,-0.667],[2.398,-0.667],[2.412,-0.679],[2.926,-0.677],[2.939,-0.658],[2.946,-0.634],[2.946,0.635],[2.939,0.659],[2.926,0.678],[2.412,0.679],[2.398,0.667],[2.363,0.667],[2.348,0.698],[2.335,0.711],[2.323,0.713],[2.277,0.71],[2.254,0.667],[2.231,0.667],[2.209,0.706],[2.199,0.713],[2.147,0.71],[2.124,0.667],[2.098,0.666],[2.076,0.708],[2.069,0.713],[2.017,0.712],[1.994,0.669],[1.965,0.669],[1.947,0.705],[1.936,0.712],[1.905,0.712],[1.88,0.705],[1.874,0.679],[1.864,0.666],[1.827,0.666],[1.807,0.677],[1.625,0.662],[1.585,0.665],[1.539,0.659],[1.501,0.633],[1.34,0.629],[1.314,0.621],[1.146,0.522],[0.864,0.521],[0.835,0.507],[0.825,0.497],[0.818,0.461],[0.659,0.457],[0.613,0.46],[0.582,0.469],[0.536,0.468],[0.531,0.473],[0.531,0.513],[0.526,0.527],[0.515,0.537],[0.478,0.546],[0.383,0.546],[0.348,0.537],[0.328,0.522],[0.314,0.522],[0.268,0.528],[0.248,0.548],[0.167,0.551],[-0.273,0.549],[-0.288,0.543],[-0.289,0.536],[-0.302,0.526],[-0.32,0.529],[-0.351,0.523],[-0.357,0.523],[-0.374,0.537],[-0.397,0.543],[-0.515,0.543],[-0.544,0.534],[-0.554,0.521],[-0.561,0.468],[-0.616,0.468],[-0.668,0.459],[-1.162,0.46],[-1.175,0.487],[-1.183,0.492],[-1.341,0.494],[-1.37,0.505],[-1.743,0.501],[-1.749,0.507],[-2.045,0.506],[-2.074,0.5],[-2.137,0.466],[-2.441,0.467],[-2.443,0.348],[-2.449,0.331],[-2.451,0.285],[-2.457,0.265]]},"features":{"body":{}},"placement":{"body":{"plane":"xz","offset":{}}},"bounds":{"min":[-2.483,0,-0.7123],"max":[2.946,1.4853,0.7123]},"volume_in3":5.2592,"centroid":[0.6678,0.7501,0],"shell":[0.7097,0.7231,0],"area_in2":25.3873,"triangles":57616,"manifold":true,"slabs":[[-2.483,0.267,-0.506,-0.931,1.279,0.506],[-0.931,0,-0.467,-0.155,1.24,0.467],[-0.155,0.347,-0.426,0.234,1.199,0.426],[0.234,0,-0.467,0.622,1.24,0.467],[0.622,0.251,-0.522,1.01,1.295,0.522],[1.01,0.061,-0.712,2.95,1.485,0.712]],"slots":["body","lens"]},"streamlight-protac-rail-mount-hl-x.mlok":{"part":"streamlight-protac-rail-mount-hl-x","component":"mlok","model":"streamlight-protac-rail-mount-hl-x.mlok.glb","script":"streamlight_protac_rail_mount_hl_x.py","inputs":{"std.mlok.slot_width":0.2755905511811024,"streamlight-protac-rail-mount-hl-x.band_front_x":0.605,"streamlight-protac-rail-mount-hl-x.band_rear_x":0.622,"streamlight-protac-rail-mount-hl-x.mlok_counterbore_depth":0.066,"streamlight-protac-rail-mount-hl-x.mlok_counterbore_diameter":0.374,"streamlight-protac-rail-mount-hl-x.mlok_edge_break":0.02,"streamlight-protac-rail-mount-hl-x.mlok_far_lip_width":0.11,"streamlight-protac-rail-mount-hl-x.mlok_length":1.498,"streamlight-protac-rail-mount-hl-x.mlok_lip_height":0.064,"streamlight-protac-rail-mount-hl-x.mlok_lug_height":0.05,"streamlight-protac-rail-mount-hl-x.mlok_lug_inner_radius":0.157,"streamlight-protac-rail-mount-hl-x.mlok_lug_outer_radius":0.236,"streamlight-protac-rail-mount-hl-x.mlok_near_lip_width":0.22,"streamlight-protac-rail-mount-hl-x.mlok_plate_height":0.798,"streamlight-protac-rail-mount-hl-x.mlok_plate_thickness":0.216,"streamlight-protac-rail-mount-hl-x.mlok_screw_below_corner":0.417,"streamlight-protac-rail-mount-hl-x.mlok_screw_head_height":0.05,"streamlight-protac-rail-mount-hl-x.mlok_screw_hole_diameter":0.215,"streamlight-protac-rail-mount-hl-x.mlok_screw_spacing":0.787,"streamlight-protac-rail-mount-hl-x.mlok_seat_angle":135,"streamlight-protac-rail-mount-hl-x.mlok_seat_counterbore_depth":0.074,"streamlight-protac-rail-mount-hl-x.mlok_seat_counterbore_diameter":0.3,"streamlight-protac-rail-mount-hl-x.mlok_seat_hole_diameter":0.176,"streamlight-protac-rail-mount-hl-x.mlok_seat_hole_from_corner":0.402,"streamlight-protac-rail-mount-hl-x.mlok_seat_hole_spacing":0.852,"streamlight-protac-rail-mount-hl-x.mlok_seat_thickness":0.226,"streamlight-protac-rail-mount-hl-x.mlok_seat_width":0.689},"profiles":{},"features":{},"placement":{},"bounds":{"min":[-0.7575,-0.653,-0.287],"max":[0.7405,0.064,0.9663]},"volume_in3":0.4133,"centroid":[-0.0085,-0.2052,0.3893],"shell":[-0.0085,-0.2095,0.3742],"area_in2":6.7326,"triangles":8690,"manifold":true,"slabs":[[-0.757,-0.653,-0.287,0.74,0.064,0.966]],"slots":["body","hardware"]},"streamlight-protac-rail-mount-hl-x.rail_clamp":{"part":"streamlight-protac-rail-mount-hl-x","component":"rail_clamp","model":"streamlight-protac-rail-mount-hl-x.rail_clamp.glb","script":"streamlight_protac_rail_mount_hl_x.py","inputs":{"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835,"streamlight-protac-rail-mount-hl-x.axis_above_mount":0.773,"streamlight-protac-rail-mount-hl-x.band_diameter":0.933,"streamlight-protac-rail-mount-hl-x.band_front_x":0.605,"streamlight-protac-rail-mount-hl-x.band_length":0.33,"streamlight-protac-rail-mount-hl-x.band_rear_x":0.622,"streamlight-protac-rail-mount-hl-x.bolt_below_axis":0.807,"streamlight-protac-rail-mount-hl-x.clamp_length":1.215,"streamlight-protac-rail-mount-hl-x.collar_diameter":0.406,"streamlight-protac-rail-mount-hl-x.fixed_jaw_length":1.094,"streamlight-protac-rail-mount-hl-x.fixed_jaw_z":0.55,"streamlight-protac-rail-mount-hl-x.front_x":2.946,"streamlight-protac-rail-mount-hl-x.head_diameter":1.424,"streamlight-protac-rail-mount-hl-x.jaw_below_bolt":0.082,"streamlight-protac-rail-mount-hl-x.jaw_chamfer":0.12,"streamlight-protac-rail-mount-hl-x.jaw_face_step":0.025,"streamlight-protac-rail-mount-hl-x.jaw_height":0.52,"streamlight-protac-rail-mount-hl-x.jaw_pad_length":0.54,"streamlight-protac-rail-mount-hl-x.lens_diameter":1.05,"streamlight-protac-rail-mount-hl-x.moving_jaw_height":0.376,"streamlight-protac-rail-mount-hl-x.moving_jaw_z":0.673,"streamlight-protac-rail-mount-hl-x.rear_x":2.483,"streamlight-protac-rail-mount-hl-x.screw_above_bolt":0.18,"streamlight-protac-rail-mount-hl-x.screw_head_diameter":0.196,"streamlight-protac-rail-mount-hl-x.screw_spacing":0.895,"streamlight-protac-rail-mount-hl-x.stud_diameter":0.167,"streamlight-protac-rail-mount-hl-x.waist_diameter":0.852,"streamlight-protac-rail-mount-hl-x.wheel_diameter":0.625,"streamlight-protac-rail-mount-hl-x.wheel_end_z":1.05,"streamlight-protac-rail-mount-hl-x.wheel_face_z":1.033,"streamlight-protac-rail-mount-hl-x.wheel_thickness":0.262},"profiles":{},"features":{},"placement":{},"bounds":{"min":[-0.6075,-0.3465,-0.55],"max":[0.6075,0.404,1.05]},"volume_in3":0.3199,"centroid":[0,0.0421,0.3682],"shell":[0,0.0493,0.2369],"area_in2":5.7553,"triangles":2640,"manifold":true,"rail_seat":{"x":[-0.547,0.547],"top_y":0,"centre_z":0,"to_y":-0.116,"reach":0.4525},"slabs":[[-0.547,-0.117,-0.55,0.547,0.404,-0.15],[-0.083,-0.117,-0.15,0.083,0.049,0.25],[-0.608,-0.117,0.25,0.608,0.26,0.65],[-0.511,-0.347,0.65,0.511,0.278,1.05]],"slots":["body","hardware"]},"superlative-750-gas-block":{"part":"superlative-750-gas-block","model":"superlative-750-gas-block.glb","script":"superlative_750_gas_block.py","inputs":{"superlative-750-gas-block.adjuster_above_bore":0.484,"superlative-750-gas-block.adjuster_d":0.147,"superlative-750-gas-block.adjuster_head_d":0.154,"superlative-750-gas-block.adjuster_hole_d":0.164,"superlative-750-gas-block.adjuster_neck_d":0.139,"superlative-750-gas-block.adjuster_neck_length":0.074,"superlative-750-gas-block.adjuster_reach":0.217,"superlative-750-gas-block.bleed_above_bore":0.463,"superlative-750-gas-block.bleed_d":0.116,"superlative-750-gas-block.bleed_z":0.119,"superlative-750-gas-block.boss_width":0.351,"superlative-750-gas-block.detent_pin_above_bore":0.324,"superlative-750-gas-block.detent_pin_d":0.064,"superlative-750-gas-block.detent_pin_rear":0.402,"superlative-750-gas-block.detent_pin_z":0.342,"superlative-750-gas-block.foot_below_bore":0.57,"superlative-750-gas-block.foot_width":0.383,"superlative-750-gas-block.height":1.383,"superlative-750-gas-block.height_above_bore":0.813,"superlative-750-gas-block.hex_key":0.09375,"superlative-750-gas-block.journal_id":0.75,"superlative-750-gas-block.length":1,"superlative-750-gas-block.pad_length":0.218,"superlative-750-gas-block.pin_hole_above_bore":0.685,"superlative-750-gas-block.pin_hole_d":0.078,"superlative-750-gas-block.pin_hole_from_front":0.311,"superlative-750-gas-block.pin_to_port":0.418,"superlative-750-gas-block.port_from_rear":0.271,"superlative-750-gas-block.scoop_d":0.145,"superlative-750-gas-block.scoop_flat_below_bore":0.359,"superlative-750-gas-block.scoop_from_front":0.508,"superlative-750-gas-block.scoop_top_below_bore":0.271,"superlative-750-gas-block.set_screw_d":0.185,"superlative-750-gas-block.set_screw_front":0.73,"superlative-750-gas-block.set_screw_length":0.1875,"superlative-750-gas-block.set_screw_rear":0.26,"superlative-750-gas-block.tab_corner_y":0.37,"superlative-750-gas-block.tab_corner_z":0.381,"superlative-750-gas-block.tab_thickness":0.166,"superlative-750-gas-block.tab_top_above_bore":0.485,"superlative-750-gas-block.tab_window_ahead":0.045,"superlative-750-gas-block.tab_window_d":0.115,"superlative-750-gas-block.tube_hole_above_bore":0.685,"superlative-750-gas-block.tube_hole_d":0.1805,"superlative-750-gas-block.tube_hole_past_pin":0.217,"superlative-750-gas-block.width":0.93},"profiles":{"front":[[-0.463,0.068],[-0.463,-0.058],[-0.459,-0.061],[-0.459,-0.078],[-0.452,-0.096],[-0.449,-0.12],[-0.445,-0.124],[-0.445,-0.134],[-0.442,-0.138],[-0.442,-0.151],[-0.431,-0.172],[-0.431,-0.179],[-0.421,-0.193],[-0.417,-0.207],[-0.4,-0.242],[-0.379,-0.273],[-0.337,-0.318],[-0.337,-0.322],[-0.278,-0.381],[-0.278,-0.384],[-0.247,-0.423],[-0.24,-0.44],[-0.23,-0.454],[-0.226,-0.468],[-0.205,-0.499],[-0.205,-0.51],[-0.202,-0.513],[-0.195,-0.551],[-0.191,-0.555],[-0.191,-0.562],[-0.183,-0.571],[0.183,-0.571],[0.191,-0.555],[0.195,-0.531],[0.212,-0.489],[0.212,-0.478],[0.219,-0.471],[0.23,-0.447],[0.247,-0.426],[0.254,-0.412],[0.282,-0.381],[0.282,-0.378],[0.327,-0.332],[0.327,-0.329],[0.379,-0.273],[0.386,-0.256],[0.393,-0.249],[0.393,-0.242],[0.4,-0.228],[0.421,-0.197],[0.428,-0.169],[0.435,-0.162],[0.445,-0.12],[0.452,-0.11],[0.456,-0.064],[0.463,-0.058],[0.463,0.029],[0.459,0.033],[0.459,0.071],[0.456,0.075],[0.456,0.089],[0.452,0.092],[0.452,0.102],[0.449,0.106],[0.449,0.116],[0.442,0.134],[0.438,0.162],[0.424,0.182],[0.39,0.256],[0.275,0.398],[0.268,0.416],[0.257,0.426],[0.216,0.513],[0.209,0.52],[0.202,0.544],[0.198,0.548],[0.198,0.558],[0.191,0.576],[0.188,0.6],[0.184,0.603],[0.184,0.621],[0.181,0.624],[0.181,0.635],[0.174,0.652],[0.174,0.676],[0.16,0.694],[0.157,0.718],[0.117,0.769],[0.113,0.769],[0.085,0.793],[0.05,0.803],[0.043,0.81],[-0.03,0.81],[-0.033,0.807],[-0.064,0.803],[-0.078,0.793],[-0.106,0.779],[-0.143,0.743],[-0.163,0.701],[-0.174,0.69],[-0.174,0.583],[-0.177,0.579],[-0.177,0.551],[-0.188,0.534],[-0.188,0.523],[-0.198,0.503],[-0.216,0.482],[-0.216,0.478],[-0.247,0.45],[-0.256,0.438],[-0.29,0.421],[-0.297,0.421],[-0.315,0.41],[-0.332,0.41],[-0.336,0.407],[-0.343,0.407],[-0.357,0.4],[-0.363,0.389],[-0.386,0.374],[-0.386,0.349],[-0.39,0.346],[-0.39,0.283],[-0.393,0.28],[-0.393,0.266],[-0.403,0.242],[-0.407,0.224],[-0.442,0.155],[-0.449,0.116],[-0.456,0.099],[-0.456,0.089],[-0.459,0.085],[-0.459,0.071]]},"features":{"front":{"tab":[[[-0.016,0.487],[-0.51,0.487],[-0.51,0.364],[-0.231,0.168],[-0.016,0.168]]]}},"placement":{"front":{"plane":"zy","offset":{}}},"bounds":{"min":[-0.271,-0.571,-0.4648],"max":[0.946,0.81,0.4648]},"volume_in3":0.4098,"centroid":[0.2482,0.0985,-0.0061],"shell":[0.2671,0.0869,-0.0131],"area_in2":8.4912,"triangles":12380,"manifold":true,"slabs":[[-0.271,-0.571,-0.406,0.729,-0.226,0.406],[-0.271,-0.226,-0.465,0.729,0.12,0.465],[-0.271,0.12,-0.449,0.946,0.465,0.449],[-0.271,0.465,-0.24,0.946,0.81,0.24]],"slots":["body","hardware","pin","screws"]},"surefire-m340c-mini-scout-light-pro.body":{"part":"surefire-m340c-mini-scout-light-pro","component":"body","model":"surefire-m340c-mini-scout-light-pro.body.glb","script":"surefire_m340c_mini_scout_light_pro.py","inputs":{"surefire-m340c-mini-scout-light-pro.axis_above_mount":0.19,"surefire-m340c-mini-scout-light-pro.barrel_diameter":0.36,"surefire-m340c-mini-scout-light-pro.barrel_front_x":1.92,"surefire-m340c-mini-scout-light-pro.barrel_rear_x":1.315,"surefire-m340c-mini-scout-light-pro.body_diameter":0.746,"surefire-m340c-mini-scout-light-pro.clamp_front_x":1.902,"surefire-m340c-mini-scout-light-pro.clamp_rear_x":1.317,"surefire-m340c-mini-scout-light-pro.ear_bottom_below_axis":0.788,"surefire-m340c-mini-scout-light-pro.head_diameter":1.125,"surefire-m340c-mini-scout-light-pro.length":4.1,"surefire-m340c-mini-scout-light-pro.lens_recess":0.08,"surefire-m340c-mini-scout-light-pro.pivot_centre_below_axis":0.609,"surefire-m340c-mini-scout-light-pro.pivot_top_below_axis":0.43,"surefire-m340c-mini-scout-light-pro.rail_centre_below_axis":1.081,"surefire-m340c-mini-scout-light-pro.ring_diameter":1.174,"surefire-m340c-mini-scout-light-pro.ring_flat_front_from_axis":0.5742,"surefire-m340c-mini-scout-light-pro.ring_flat_front_x":3.239,"surefire-m340c-mini-scout-light-pro.ring_flat_rear_from_axis":0.5627,"surefire-m340c-mini-scout-light-pro.ring_flat_rear_x":3.017,"surefire-m340c-mini-scout-light-pro.ring_flats":6,"surefire-m340c-mini-scout-light-pro.ring_front_x":3.28,"surefire-m340c-mini-scout-light-pro.ring_rear_x":2.967,"surefire-m340c-mini-scout-light-pro.screw_head_front_x":2.178,"surefire-m340c-mini-scout-light-pro.shroud_hole_diameter":0.121,"surefire-m340c-mini-scout-light-pro.shroud_hole_x":0.11,"surefire-m340c-mini-scout-light-pro.shroud_holes":4,"surefire-m340c-mini-scout-light-pro.tailcap_diameter":0.989},"profiles":{"side":[[0,0.477],[0,-0.001],[0,-0.477],[0.009,-0.493],[0.021,-0.496],[0.406,-0.496],[0.527,-0.396],[0.553,-0.396],[0.561,-0.381],[0.598,-0.381],[0.606,-0.396],[0.851,-0.396],[0.86,-0.381],[0.894,-0.381],[0.903,-0.396],[0.99,-0.396],[1,-0.386],[1.015,-0.394],[1.313,-0.394],[1.318,-0.389],[1.325,-0.396],[1.325,-0.279],[1.333,-0.272],[1.339,-0.274],[1.325,-0.248],[1.316,-0.205],[1.323,-0.198],[1.895,-0.198],[1.902,-0.205],[1.894,-0.243],[1.881,-0.273],[1.887,-0.269],[1.894,-0.276],[1.895,-0.397],[1.902,-0.391],[1.907,-0.394],[2.226,-0.394],[2.253,-0.42],[2.317,-0.42],[2.324,-0.428],[2.324,-0.492],[2.329,-0.495],[2.48,-0.495],[2.51,-0.508],[2.534,-0.543],[2.558,-0.557],[2.887,-0.557],[2.899,-0.547],[2.947,-0.547],[2.95,-0.544],[2.972,-0.574],[3,-0.587],[3.253,-0.587],[3.273,-0.579],[3.293,-0.551],[3.301,-0.557],[4.064,-0.556],[4.1,-0.5],[4.1,-0.392],[4.07,-0.309],[4.064,-0.274],[4.064,-0.23],[4.072,-0.177],[4.1,-0.085],[4.1,0.083],[4.069,0.197],[4.064,0.225],[4.064,0.276],[4.077,0.332],[4.1,0.39],[4.1,0.499],[4.061,0.556],[3.298,0.556],[3.293,0.551],[3.272,0.579],[3.249,0.587],[3.006,0.587],[2.978,0.579],[2.952,0.544],[2.899,0.546],[2.889,0.556],[2.556,0.556],[2.531,0.538],[2.513,0.511],[2.489,0.496],[2.329,0.495],[2.324,0.49],[2.324,0.428],[2.319,0.422],[2.254,0.42],[2.226,0.392],[1.905,0.392],[1.885,0.373],[1.335,0.373],[1.315,0.392],[1.011,0.392],[0.998,0.384],[0.99,0.396],[0.903,0.396],[0.894,0.381],[0.86,0.381],[0.851,0.396],[0.606,0.396],[0.598,0.381],[0.561,0.381],[0.554,0.388],[0.555,0.396],[0.525,0.396],[0.408,0.495],[0.017,0.495],[0.005,0.489]],"lug_front":[[1.92,-0.403],[1.922,-0.784],[2.172,-0.781],[2.182,-0.768],[2.188,-0.701],[2.188,-0.557],[2.179,-0.549],[2.185,-0.529],[2.182,-0.453],[2.172,-0.44],[2.163,-0.438],[2.037,-0.438],[2.034,-0.401]],"lug_rear":[[0.972,-0.559],[0.972,-0.663],[0.979,-0.676],[0.989,-0.672],[0.989,-0.759],[1.002,-0.783],[1.311,-0.788],[1.315,-0.787],[1.313,-0.403],[0.99,-0.403],[0.988,-0.54]]},"features":{"side":{},"lug_front":{},"lug_rear":{}},"placement":{"side":{"plane":"xy","offset":{}},"lug_front":{"plane":"xy","offset":{}},"lug_rear":{"plane":"xy","offset":{}}},"bounds":{"min":[-1.6095,-0.386,0.293],"max":[2.4905,0.766,1.668]},"volume_in3":2.7592,"centroid":[0.8131,0.19,1.066],"shell":[0.4822,0.19,1.0432],"area_in2":19.2639,"triangles":53414,"manifold":true,"slabs":[[-1.61,-0.305,0.586,-0.864,0.685,1.576],[-0.864,-0.206,0.293,-0.119,0.586,1.477],[-0.119,-0.183,0.708,0.254,0.563,1.454],[0.254,-0.212,0.297,0.627,0.592,1.483],[0.627,-0.386,0.494,2.49,0.766,1.668]],"slots":["body","lens","button","hardware"]},"surefire-m340c-mini-scout-light-pro.mlok":{"part":"surefire-m340c-mini-scout-light-pro","component":"mlok","model":"surefire-m340c-mini-scout-light-pro.mlok.glb","script":"surefire_m340c_mini_scout_light_pro.py","inputs":{"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835,"surefire-m340c-mini-scout-light-pro.axis_above_mount":0.19,"surefire-m340c-mini-scout-light-pro.barrel_diameter":0.36,"surefire-m340c-mini-scout-light-pro.barrel_front_x":1.92,"surefire-m340c-mini-scout-light-pro.barrel_rear_x":1.315,"surefire-m340c-mini-scout-light-pro.body_diameter":0.746,"surefire-m340c-mini-scout-light-pro.clamp_front_x":1.902,"surefire-m340c-mini-scout-light-pro.clamp_rear_x":1.317,"surefire-m340c-mini-scout-light-pro.clamp_thickness":0.22,"surefire-m340c-mini-scout-light-pro.ear_bottom_below_axis":0.788,"surefire-m340c-mini-scout-light-pro.head_diameter":1.125,"surefire-m340c-mini-scout-light-pro.hook_back_beyond_pivot":0.07,"surefire-m340c-mini-scout-light-pro.jaw_bottom_below_axis":1.618,"surefire-m340c-mini-scout-light-pro.jaw_reach":0.1,"surefire-m340c-mini-scout-light-pro.length":4.1,"surefire-m340c-mini-scout-light-pro.lens_recess":0.08,"surefire-m340c-mini-scout-light-pro.mlok_base_thickness":0.15,"surefire-m340c-mini-scout-light-pro.mlok_base_width":0.4,"surefire-m340c-mini-scout-light-pro.mlok_counterbore_diameter":0.31,"surefire-m340c-mini-scout-light-pro.mlok_pivot_above_face":0.4,"surefire-m340c-mini-scout-light-pro.mlok_screw_spacing":0.64,"surefire-m340c-mini-scout-light-pro.mount_screw_head_diameter":0.19,"surefire-m340c-mini-scout-light-pro.mount_screw_head_proud":0.04,"surefire-m340c-mini-scout-light-pro.pivot_centre_below_axis":0.609,"surefire-m340c-mini-scout-light-pro.pivot_top_below_axis":0.43,"surefire-m340c-mini-scout-light-pro.rail_centre_below_axis":1.081,"surefire-m340c-mini-scout-light-pro.recoil_bar_width":0.2,"surefire-m340c-mini-scout-light-pro.ring_diameter":1.174,"surefire-m340c-mini-scout-light-pro.ring_flat_front_from_axis":0.5742,"surefire-m340c-mini-scout-light-pro.ring_flat_front_x":3.239,"surefire-m340c-mini-scout-light-pro.ring_flat_rear_from_axis":0.5627,"surefire-m340c-mini-scout-light-pro.ring_flat_rear_x":3.017,"surefire-m340c-mini-scout-light-pro.ring_flats":6,"surefire-m340c-mini-scout-light-pro.ring_front_x":3.28,"surefire-m340c-mini-scout-light-pro.ring_rear_x":2.967,"surefire-m340c-mini-scout-light-pro.screw_head_front_x":2.178,"surefire-m340c-mini-scout-light-pro.shroud_hole_diameter":0.121,"surefire-m340c-mini-scout-light-pro.shroud_hole_x":0.11,"surefire-m340c-mini-scout-light-pro.shroud_holes":4,"surefire-m340c-mini-scout-light-pro.tailcap_diameter":0.989},"profiles":{},"bounds":{"min":[-0.512,0.01,0.072],"max":[0.528,0.59,0.652]},"volume_in3":0.1302,"centroid":[0.008,0.286,0.3119],"shell":[0.008,0.3253,0.2585],"area_in2":2.6097,"triangles":3506,"manifold":true,"slabs":[[-0.512,0.01,0.072,0.528,0.59,0.652]],"slots":["body","hardware"]},"surefire-m340c-mini-scout-light-pro.rail_clamp":{"part":"surefire-m340c-mini-scout-light-pro","component":"rail_clamp","model":"surefire-m340c-mini-scout-light-pro.rail_clamp.glb","script":"surefire_m340c_mini_scout_light_pro.py","inputs":{"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835,"surefire-m340c-mini-scout-light-pro.axis_above_mount":0.19,"surefire-m340c-mini-scout-light-pro.barrel_diameter":0.36,"surefire-m340c-mini-scout-light-pro.barrel_front_x":1.92,"surefire-m340c-mini-scout-light-pro.barrel_rear_x":1.315,"surefire-m340c-mini-scout-light-pro.body_diameter":0.746,"surefire-m340c-mini-scout-light-pro.clamp_front_x":1.902,"surefire-m340c-mini-scout-light-pro.clamp_rear_x":1.317,"surefire-m340c-mini-scout-light-pro.clamp_thickness":0.22,"surefire-m340c-mini-scout-light-pro.ear_bottom_below_axis":0.788,"surefire-m340c-mini-scout-light-pro.head_diameter":1.125,"surefire-m340c-mini-scout-light-pro.hook_back_beyond_pivot":0.07,"surefire-m340c-mini-scout-light-pro.jaw_bottom_below_axis":1.618,"surefire-m340c-mini-scout-light-pro.jaw_reach":0.1,"surefire-m340c-mini-scout-light-pro.length":4.1,"surefire-m340c-mini-scout-light-pro.lens_recess":0.08,"surefire-m340c-mini-scout-light-pro.mount_screw_head_diameter":0.19,"surefire-m340c-mini-scout-light-pro.mount_screw_head_proud":0.04,"surefire-m340c-mini-scout-light-pro.pivot_centre_below_axis":0.609,"surefire-m340c-mini-scout-light-pro.pivot_top_below_axis":0.43,"surefire-m340c-mini-scout-light-pro.rail_centre_below_axis":1.081,"surefire-m340c-mini-scout-light-pro.recoil_bar_width":0.2,"surefire-m340c-mini-scout-light-pro.ring_diameter":1.174,"surefire-m340c-mini-scout-light-pro.ring_flat_front_from_axis":0.5742,"surefire-m340c-mini-scout-light-pro.ring_flat_front_x":3.239,"surefire-m340c-mini-scout-light-pro.ring_flat_rear_from_axis":0.5627,"surefire-m340c-mini-scout-light-pro.ring_flat_rear_x":3.017,"surefire-m340c-mini-scout-light-pro.ring_flats":6,"surefire-m340c-mini-scout-light-pro.ring_front_x":3.28,"surefire-m340c-mini-scout-light-pro.ring_rear_x":2.967,"surefire-m340c-mini-scout-light-pro.screw_head_front_x":2.178,"surefire-m340c-mini-scout-light-pro.shroud_hole_diameter":0.121,"surefire-m340c-mini-scout-light-pro.shroud_hole_x":0.11,"surefire-m340c-mini-scout-light-pro.shroud_holes":4,"surefire-m340c-mini-scout-light-pro.tailcap_diameter":0.989},"profiles":{"clamp":[[1.323,-0.443],[1.325,-1.549],[1.348,-1.589],[1.377,-1.61],[1.501,-1.612],[1.504,-1.618],[1.825,-1.615],[1.839,-1.609],[1.866,-1.585],[1.88,-1.56],[1.885,-1.515],[1.885,-1.32],[1.891,-1.281],[1.89,-0.971],[1.895,-0.797],[1.899,-0.784],[1.912,-0.783],[1.91,-0.43],[1.899,-0.43],[1.896,-0.441],[1.327,-0.439]]},"features":{"clamp":{}},"placement":{"clamp":{"plane":"xy","offset":{}}},"bounds":{"min":[-0.2945,-0.1,-0.577],"max":[0.3105,0.37,0.652]},"volume_in3":0.2239,"centroid":[0.0015,0.1867,0.0541],"shell":[0.0018,0.1621,0.0053],"area_in2":3.2104,"triangles":2518,"manifold":true,"rail_seat":{"x":[-0.2925,0.2925],"top_y":0,"centre_z":0,"to_y":-0.1,"reach":0.4525},"slabs":[[-0.292,-0.1,-0.577,0.292,0.37,-0.27],[-0.295,-0.017,-0.27,0.31,0.37,0.345],[-0.295,-0.1,0.345,0.31,0.37,0.652]],"slots":["body","hardware"]},"surefire-procomp-556":{"part":"surefire-procomp-556","model":"surefire-procomp-556.glb","script":"surefire_procomp_556.py","inputs":{"surefire-procomp-556.bore_d":0.244,"surefire-procomp-556.chamber_cone":0.058,"surefire-procomp-556.chamber_d":0.4551,"surefire-procomp-556.chamber_front_x":1.006,"surefire-procomp-556.flats_across":0.774,"surefire-procomp-556.flats_rear_x":1.187,"surefire-procomp-556.flats_runout":0.057,"surefire-procomp-556.groove_depth":0.018,"surefire-procomp-556.groove_front_x":0.728,"surefire-procomp-556.groove_pitch":0.0835,"surefire-procomp-556.groove_width":0.05,"surefire-procomp-556.grooves":3,"surefire-procomp-556.land_width":0.088,"surefire-procomp-556.length":2.5,"surefire-procomp-556.od":0.864,"surefire-procomp-556.overall_length":2.5,"surefire-procomp-556.pilot_hole_d":0.103,"surefire-procomp-556.pilot_hole_depth":0.04,"surefire-procomp-556.pilot_hole_x":0.917,"surefire-procomp-556.pin_hole_d":0.088,"surefire-procomp-556.pin_hole_x":0.225,"surefire-procomp-556.pocket_front_x":2.245,"surefire-procomp-556.pocket_outer_z":0.3,"surefire-procomp-556.pocket_rear_x":0.347,"surefire-procomp-556.pocket_tilt":24,"surefire-procomp-556.rear_face_d":0.754,"surefire-procomp-556.rear_taper_x":0.196,"surefire-procomp-556.thread_depth":0.69,"surefire-procomp-556.thread_major_d":0.4957,"surefire-procomp-556.thread_minor_d":0.4551,"surefire-procomp-556.thread_pitch":0.03571,"surefire-procomp-556.top_hole_d":0.124,"surefire-procomp-556.top_left_hole_x":0.965,"surefire-procomp-556.top_right_hole_x":0.965,"surefire-procomp-556.window_corner_r":0.09,"surefire-procomp-556.window_front_front_x":2.291,"surefire-procomp-556.window_front_rear_x":1.887,"surefire-procomp-556.window_height":0.584,"surefire-procomp-556.window_rear_front_x":1.718,"surefire-procomp-556.window_rear_rear_x":1.142,"surefire-procomp-556.windows":2},"profiles":{},"bounds":{"min":[0,-0.432,-0.432],"max":[2.5,0.432,0.432]},"volume_in3":0.7522,"centroid":[1.1593,-0.0014,0],"shell":[1.2088,0.0015,0.0001],"area_in2":11.7624,"triangles":24132,"manifold":true,"slabs":[[0,-0.432,-0.432,2.5,0.432,0.432]],"slots":["body"]},"surefire-scout-light-pro-dual-fuel.body":{"part":"surefire-scout-light-pro-dual-fuel","component":"body","model":"surefire-scout-light-pro-dual-fuel.body.glb","script":"surefire_scout_light_pro_dual_fuel.py","inputs":{"surefire-scout-light-pro-dual-fuel.axis_above_mount":0.19,"surefire-scout-light-pro-dual-fuel.barrel_front_x":1.965,"surefire-scout-light-pro-dual-fuel.barrel_rear_x":1.412,"surefire-scout-light-pro-dual-fuel.body_diameter":0.843,"surefire-scout-light-pro-dual-fuel.clamp_front_x":1.999,"surefire-scout-light-pro-dual-fuel.clamp_rear_x":1.406,"surefire-scout-light-pro-dual-fuel.ear_bottom_below_axis":0.831,"surefire-scout-light-pro-dual-fuel.head_diameter":1.125,"surefire-scout-light-pro-dual-fuel.length":5.56,"surefire-scout-light-pro-dual-fuel.pivot_top_below_axis":0.471,"surefire-scout-light-pro-dual-fuel.rail_centre_below_axis":1.123,"surefire-scout-light-pro-dual-fuel.rear_face_x":0.044,"surefire-scout-light-pro-dual-fuel.ring_diameter":1.178,"surefire-scout-light-pro-dual-fuel.tailcap_diameter":0.989},"profiles":{"side":[[0,0.127],[0.009,0.116],[0.009,-0.102],[0.003,-0.085],[0,0.045],[0,-0.128],[0.02,-0.428],[0.034,-0.476],[0.059,-0.5],[0.325,-0.501],[0.468,-0.402],[0.585,-0.403],[0.597,-0.391],[0.614,-0.389],[0.651,-0.389],[0.665,-0.406],[0.68,-0.411],[0.874,-0.406],[0.886,-0.404],[0.891,-0.392],[0.917,-0.39],[0.951,-0.39],[0.96,-0.401],[1.037,-0.401],[1.05,-0.38],[1.051,-0.35],[1.064,-0.428],[1.086,-0.447],[1.391,-0.447],[1.417,-0.428],[1.571,-0.425],[1.97,-0.427],[1.993,-0.446],[2.318,-0.447],[2.341,-0.425],[3.598,-0.426],[3.658,-0.482],[3.697,-0.488],[3.707,-0.523],[3.737,-0.536],[3.956,-0.537],[4.046,-0.56],[4.381,-0.561],[4.401,-0.549],[4.455,-0.547],[4.465,-0.565],[4.497,-0.589],[4.602,-0.592],[4.781,-0.587],[4.809,-0.553],[4.817,-0.562],[5.505,-0.564],[5.587,-0.561],[5.612,-0.55],[5.631,-0.532],[5.636,-0.464],[5.668,-0.402],[5.679,-0.355],[5.679,-0.248],[5.653,-0.132],[5.653,-0.011],[5.668,0.065],[5.69,0.138],[5.69,0.158],[5.682,0.279],[5.659,0.327],[5.622,0.445],[5.636,0.487],[5.639,0.526],[5.595,0.556],[5.567,0.562],[5.166,0.564],[4.823,0.562],[4.8,0.554],[4.775,0.588],[4.679,0.591],[4.492,0.589],[4.466,0.575],[4.446,0.547],[4.395,0.55],[4.387,0.558],[4.041,0.557],[3.995,0.543],[3.93,0.535],[3.729,0.533],[3.704,0.523],[3.695,0.485],[3.658,0.48],[3.598,0.421],[2.338,0.42],[2.318,0.44],[2.292,0.443],[1.993,0.441],[1.962,0.419],[1.457,0.421],[1.408,0.424],[1.391,0.443],[1.088,0.442],[1.071,0.433],[1.061,0.418],[1.051,0.343],[1.047,0.378],[1.031,0.397],[0.957,0.397],[0.948,0.389],[0.894,0.389],[0.871,0.403],[0.668,0.404],[0.648,0.384],[0.591,0.384],[0.582,0.396],[0.471,0.396],[0.322,0.496],[0.059,0.497],[0.037,0.479],[0.026,0.45],[0.011,0.357],[0.003,0.246],[0.006,0.13]],"lug_front":[[1.963,-0.469],[1.965,-0.826],[2.086,-0.827],[2.09,-0.831],[2.105,-0.827],[2.115,-0.817],[2.118,-0.76],[2.124,-0.75],[2.145,-0.752],[2.149,-0.81],[2.153,-0.825],[2.163,-0.831],[2.293,-0.83],[2.305,-0.826],[2.318,-0.809],[2.322,-0.77],[2.325,-0.767],[2.325,-0.74],[2.318,-0.709],[2.325,-0.694],[2.324,-0.544],[2.321,-0.54],[2.32,-0.506],[2.313,-0.487],[2.299,-0.477],[2.161,-0.478],[2.152,-0.487],[2.148,-0.549],[2.142,-0.558],[2.131,-0.558],[2.125,-0.553],[2.126,-0.447],[1.969,-0.448]],"lug_rear":[[1.031,-0.454],[1.031,-0.477],[1.035,-0.481],[1.036,-0.731],[1.04,-0.734],[1.044,-0.784],[1.056,-0.811],[1.077,-0.824],[1.315,-0.823],[1.319,-0.827],[1.361,-0.827],[1.388,-0.823],[1.392,-0.831],[1.413,-0.828],[1.409,-0.451]]},"features":{"side":{},"lug_front":{},"lug_rear":{}},"placement":{"side":{"plane":"xy","offset":{}},"lug_front":{"plane":"xy","offset":{}},"lug_rear":{"plane":"xy","offset":{}}},"bounds":{"min":[-1.6585,-0.4011,0.292],"max":[3.9015,0.7811,1.7141]},"volume_in3":3.9017,"centroid":[1.5223,0.19,1.1093],"shell":[1.1679,0.19,1.0879],"area_in2":23.7058,"triangles":48034,"manifold":true,"slabs":[[-1.658,-0.308,0.625,-1.261,0.688,1.622],[-1.261,-0.228,0.705,-0.864,0.608,1.541],[-0.864,-0.255,0.292,0.724,0.635,1.568],[0.724,-0.253,0.68,1.916,0.633,1.566],[1.916,-0.401,0.532,3.901,0.781,1.714]],"slots":["body","lens","button","hardware"]},"surefire-scout-light-pro-dual-fuel.mlok":{"part":"surefire-scout-light-pro-dual-fuel","component":"mlok","model":"surefire-scout-light-pro-dual-fuel.mlok.glb","script":"surefire_scout_light_pro_dual_fuel.py","inputs":{"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835,"surefire-scout-light-pro-dual-fuel.axis_above_mount":0.19,"surefire-scout-light-pro-dual-fuel.barrel_front_x":1.965,"surefire-scout-light-pro-dual-fuel.barrel_rear_x":1.412,"surefire-scout-light-pro-dual-fuel.body_diameter":0.843,"surefire-scout-light-pro-dual-fuel.clamp_front_x":1.999,"surefire-scout-light-pro-dual-fuel.clamp_rear_x":1.406,"surefire-scout-light-pro-dual-fuel.clamp_thickness":0.22,"surefire-scout-light-pro-dual-fuel.ear_bottom_below_axis":0.831,"surefire-scout-light-pro-dual-fuel.head_diameter":1.125,"surefire-scout-light-pro-dual-fuel.hook_back_beyond_pivot":0.07,"surefire-scout-light-pro-dual-fuel.jaw_bottom_below_axis":1.62,"surefire-scout-light-pro-dual-fuel.jaw_reach":0.1,"surefire-scout-light-pro-dual-fuel.length":5.56,"surefire-scout-light-pro-dual-fuel.mlok_base_thickness":0.15,"surefire-scout-light-pro-dual-fuel.mlok_base_width":0.4,"surefire-scout-light-pro-dual-fuel.mlok_counterbore_diameter":0.31,"surefire-scout-light-pro-dual-fuel.mlok_pivot_above_face":0.4,"surefire-scout-light-pro-dual-fuel.mlok_screw_spacing":0.64,"surefire-scout-light-pro-dual-fuel.mount_screw_head_diameter":0.19,"surefire-scout-light-pro-dual-fuel.mount_screw_head_proud":0.04,"surefire-scout-light-pro-dual-fuel.pivot_top_below_axis":0.471,"surefire-scout-light-pro-dual-fuel.rail_centre_below_axis":1.123,"surefire-scout-light-pro-dual-fuel.rear_face_x":0.044,"surefire-scout-light-pro-dual-fuel.recoil_bar_width":0.2,"surefire-scout-light-pro-dual-fuel.ring_diameter":1.178,"surefire-scout-light-pro-dual-fuel.tailcap_diameter":0.989},"profiles":{},"bounds":{"min":[-0.534,0.01,0.072],"max":[0.506,0.59,0.652]},"volume_in3":0.1234,"centroid":[-0.014,0.2899,0.3058],"shell":[-0.014,0.328,0.254],"area_in2":2.544,"triangles":3562,"manifold":true,"slabs":[[-0.534,0.01,0.072,0.506,0.59,0.652]],"slots":["body","hardware"]},"surefire-scout-light-pro-dual-fuel.rail_clamp":{"part":"surefire-scout-light-pro-dual-fuel","component":"rail_clamp","model":"surefire-scout-light-pro-dual-fuel.rail_clamp.glb","script":"surefire_scout_light_pro_dual_fuel.py","inputs":{"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835,"surefire-scout-light-pro-dual-fuel.axis_above_mount":0.19,"surefire-scout-light-pro-dual-fuel.barrel_front_x":1.965,"surefire-scout-light-pro-dual-fuel.barrel_rear_x":1.412,"surefire-scout-light-pro-dual-fuel.body_diameter":0.843,"surefire-scout-light-pro-dual-fuel.clamp_front_x":1.999,"surefire-scout-light-pro-dual-fuel.clamp_rear_x":1.406,"surefire-scout-light-pro-dual-fuel.clamp_thickness":0.22,"surefire-scout-light-pro-dual-fuel.ear_bottom_below_axis":0.831,"surefire-scout-light-pro-dual-fuel.head_diameter":1.125,"surefire-scout-light-pro-dual-fuel.hook_back_beyond_pivot":0.07,"surefire-scout-light-pro-dual-fuel.jaw_bottom_below_axis":1.62,"surefire-scout-light-pro-dual-fuel.jaw_reach":0.1,"surefire-scout-light-pro-dual-fuel.length":5.56,"surefire-scout-light-pro-dual-fuel.mount_screw_head_diameter":0.19,"surefire-scout-light-pro-dual-fuel.mount_screw_head_proud":0.04,"surefire-scout-light-pro-dual-fuel.pivot_top_below_axis":0.471,"surefire-scout-light-pro-dual-fuel.rail_centre_below_axis":1.123,"surefire-scout-light-pro-dual-fuel.rear_face_x":0.044,"surefire-scout-light-pro-dual-fuel.recoil_bar_width":0.2,"surefire-scout-light-pro-dual-fuel.ring_diameter":1.178,"surefire-scout-light-pro-dual-fuel.tailcap_diameter":0.989},"profiles":{"clamp":[[1.394,-0.836],[1.402,-0.898],[1.406,-0.901],[1.41,-0.982],[1.414,-0.986],[1.419,-1.289],[1.427,-1.312],[1.427,-1.411],[1.431,-1.415],[1.436,-1.565],[1.451,-1.595],[1.484,-1.62],[1.821,-1.619],[1.825,-1.615],[1.944,-1.61],[1.967,-1.599],[1.98,-1.585],[1.996,-1.558],[1.995,-1.543],[1.999,-1.539],[1.998,-1.374],[1.995,-1.37],[1.994,-1.263],[1.99,-1.259],[1.988,-0.833],[1.965,-0.83],[1.962,-0.471],[1.413,-0.474],[1.413,-0.832]]},"features":{"clamp":{}},"placement":{"clamp":{"plane":"xy","offset":{}}},"bounds":{"min":[-0.3085,-0.1,-0.537],"max":[0.2965,0.37,0.652]},"volume_in3":0.2084,"centroid":[-0.0033,0.1907,0.0698],"shell":[-0.0032,0.166,0.0209],"area_in2":3.0251,"triangles":2846,"manifold":true,"rail_seat":{"x":[-0.2965,0.2965],"top_y":0,"centre_z":0,"to_y":-0.1,"reach":0.4525},"slabs":[[-0.296,-0.1,-0.537,0.296,0.37,-0.141],[-0.304,0,-0.141,0.292,0.37,0.256],[-0.308,-0.1,0.256,0.286,0.37,0.652]],"slots":["body","hardware"]},"surefire-socom-3-prong":{"part":"surefire-socom-3-prong","model":"surefire-socom-3-prong.glb","script":"surefire_socom_3_prong.py","inputs":{"surefire-socom-3-prong.body_od":0.862,"surefire-socom-3-prong.bore_d":0.244,"surefire-socom-3-prong.bore_mouth_d":0.308,"surefire-socom-3-prong.boss_length":0.167,"surefire-socom-3-prong.boss_od":0.685,"surefire-socom-3-prong.collar_od":0.88,"surefire-socom-3-prong.cone_length":0.056,"surefire-socom-3-prong.flange_length":0.137,"surefire-socom-3-prong.flats":2,"surefire-socom-3-prong.flats_across":0.731,"surefire-socom-3-prong.flats_length":0.274,"surefire-socom-3-prong.flats_x":0.442,"surefire-socom-3-prong.front_od":0.81,"surefire-socom-3-prong.groove_1_x":0.766,"surefire-socom-3-prong.groove_d":0.833,"surefire-socom-3-prong.groove_pitch":0.084,"surefire-socom-3-prong.groove_width":0.046,"surefire-socom-3-prong.length":2.618,"surefire-socom-3-prong.nose_r":0.109,"surefire-socom-3-prong.od":0.962,"surefire-socom-3-prong.overall_length":2.6,"surefire-socom-3-prong.pocket_floor_d":0.817,"surefire-socom-3-prong.pocket_front_x":0.48,"surefire-socom-3-prong.pocket_rear_x":0.253,"surefire-socom-3-prong.pocket_width":0.12,"surefire-socom-3-prong.seal_front_x":0.96,"surefire-socom-3-prong.seal_grooves":2,"surefire-socom-3-prong.shim_stack":0.018,"surefire-socom-3-prong.slot_root_r":0.075,"surefire-socom-3-prong.slot_root_x":1.015,"surefire-socom-3-prong.slot_width":0.298,"surefire-socom-3-prong.step_front_od":0.83,"surefire-socom-3-prong.step_rear_od":0.842,"surefire-socom-3-prong.step_x":1.992,"surefire-socom-3-prong.tab_front_x":0.401,"surefire-socom-3-prong.tab_lip_length":0.104,"surefire-socom-3-prong.tab_width":0.12,"surefire-socom-3-prong.taper_x":1.571,"surefire-socom-3-prong.thread_depth":0.69,"surefire-socom-3-prong.thread_major_d":0.4957,"surefire-socom-3-prong.thread_minor_d":0.4551,"surefire-socom-3-prong.thread_pitch":0.03571,"surefire-socom-3-prong.tines":3},"profiles":{},"bounds":{"min":[0,-0.481,-0.481],"max":[2.618,0.481,0.481]},"volume_in3":0.7946,"centroid":[1.1206,0.0006,0],"shell":[1.1238,-0.0016,-0.0001],"area_in2":12.0245,"triangles":23650,"manifold":true,"slabs":[[0,-0.481,-0.481,1.122,0.481,0.481],[1.122,-0.431,-0.431,2.618,0.404,0.431]],"slots":["body","shims"]},"surefire-socom-4-prong":{"part":"surefire-socom-4-prong","model":"surefire-socom-4-prong.glb","script":"surefire_socom_4_prong.py","inputs":{"surefire-socom-4-prong.body_od":0.844,"surefire-socom-4-prong.bore_d":0.244,"surefire-socom-4-prong.boss_length":0.168,"surefire-socom-4-prong.boss_od":0.674,"surefire-socom-4-prong.collar_od":0.862,"surefire-socom-4-prong.cone_length":0.06,"surefire-socom-4-prong.flange_length":0.135,"surefire-socom-4-prong.flats":2,"surefire-socom-4-prong.flats_across":0.8,"surefire-socom-4-prong.flats_length":0.295,"surefire-socom-4-prong.flats_x":0.457,"surefire-socom-4-prong.front_od":0.785,"surefire-socom-4-prong.groove_1_x":0.79,"surefire-socom-4-prong.groove_d":0.814,"surefire-socom-4-prong.groove_pitch":0.08,"surefire-socom-4-prong.groove_width":0.04,"surefire-socom-4-prong.length":2.618,"surefire-socom-4-prong.nose_r":0.122,"surefire-socom-4-prong.od":0.945,"surefire-socom-4-prong.overall_length":2.6,"surefire-socom-4-prong.pocket_floor_d":0.817,"surefire-socom-4-prong.pocket_front_x":0.48,"surefire-socom-4-prong.pocket_rear_x":0.253,"surefire-socom-4-prong.pocket_width":0.12,"surefire-socom-4-prong.seal_front_x":0.962,"surefire-socom-4-prong.seal_grooves":2,"surefire-socom-4-prong.shim_stack":0.018,"surefire-socom-4-prong.slot_offset":0.074,"surefire-socom-4-prong.slot_root_r":0.09,"surefire-socom-4-prong.slot_root_x":1.006,"surefire-socom-4-prong.slot_width":0.19,"surefire-socom-4-prong.step_front_od":0.805,"surefire-socom-4-prong.step_rear_od":0.825,"surefire-socom-4-prong.step_x":1.999,"surefire-socom-4-prong.tab_front_x":0.401,"surefire-socom-4-prong.tab_width":0.12,"surefire-socom-4-prong.taper_x":1.473,"surefire-socom-4-prong.thread_depth":0.69,"surefire-socom-4-prong.thread_major_d":0.4957,"surefire-socom-4-prong.thread_minor_d":0.4551,"surefire-socom-4-prong.thread_pitch":0.03571,"surefire-socom-4-prong.tines":4},"profiles":{},"bounds":{"min":[0,-0.4725,-0.4725],"max":[2.618,0.4725,0.4725]},"volume_in3":0.8018,"centroid":[1.1431,0.0004,0],"shell":[1.1826,-0.0013,-0.0001],"area_in2":12.742,"triangles":23338,"manifold":true,"slabs":[[0,-0.472,-0.472,1.122,0.472,0.472],[1.122,-0.422,-0.422,2.618,0.422,0.422]],"slots":["body","shims"]},"surefire-socom556-rc2":{"part":"surefire-socom556-rc2","model":"surefire-socom556-rc2.glb","script":"surefire_socom556_rc2.py","inputs":{"surefire-socom556-rc2.body_rear_x":0.83,"surefire-socom556-rc2.body_shoulder_round":0.09,"surefire-socom556-rc2.bore_d":0.35,"surefire-socom556-rc2.boss_d":0.48,"surefire-socom556-rc2.boss_height":0.06,"surefire-socom556-rc2.collar_d":1.26,"surefire-socom556-rc2.crown_across_flats":1.22,"surefire-socom556-rc2.crown_flats":8,"surefire-socom556-rc2.dish_d":0.9,"surefire-socom556-rc2.flute_depth":0.03,"surefire-socom556-rc2.flute_length":0.61,"surefire-socom556-rc2.flute_pitch":45,"surefire-socom556-rc2.flute_width":0.41,"surefire-socom556-rc2.flutes":6,"surefire-socom556-rc2.front_corner_round":0.075,"surefire-socom556-rc2.front_recess":0.16,"surefire-socom556-rc2.half_length":3.2,"surefire-socom556-rc2.latch_angle":136,"surefire-socom556-rc2.latch_arm_width":0.15,"surefire-socom556-rc2.latch_pocket_ahead":25,"surefire-socom556-rc2.latch_pocket_behind":47,"surefire-socom556-rc2.latch_pocket_depth":0.06,"surefire-socom556-rc2.latch_pocket_x":0.17,"surefire-socom556-rc2.latch_proud":0.037,"surefire-socom556-rc2.latch_width":0.3,"surefire-socom556-rc2.latch_x0":0.4,"surefire-socom556-rc2.latch_x1":0.73,"surefire-socom556-rc2.length":6.4,"surefire-socom556-rc2.od":1.5,"surefire-socom556-rc2.rear_bore_d":1.03,"surefire-socom556-rc2.ring_d":1.5,"surefire-socom556-rc2.ring_front_chamfer":0.05,"surefire-socom556-rc2.ring_length":0.8,"surefire-socom556-rc2.ring_rear_round":0.09},"profiles":{"side":[[-3.2,0.648],[-3.2,-0.649],[-3.153,-0.7],[-3.107,-0.722],[-2.464,-0.722],[-2.439,-0.714],[-2.402,-0.682],[-2.375,-0.629],[-2.373,-0.653],[-2.351,-0.704],[-2.302,-0.74],[-2.281,-0.749],[1.823,-0.752],[1.828,-0.748],[2.134,-0.75],[2.139,-0.746],[2.143,-0.75],[2.198,-0.746],[2.203,-0.75],[2.42,-0.752],[2.433,-0.748],[2.437,-0.752],[2.441,-0.748],[2.757,-0.75],[2.761,-0.746],[2.948,-0.751],[2.953,-0.747],[3.136,-0.744],[3.179,-0.727],[3.198,-0.704],[3.2,0.694],[3.179,0.728],[3.136,0.745],[2.953,0.746],[2.948,0.751],[2.45,0.75],[2.446,0.746],[2.437,0.75],[2.433,0.746],[2.42,0.75],[2.203,0.752],[2.198,0.747],[2.143,0.752],[2.139,0.748],[0.891,0.752],[0.886,0.748],[0.58,0.75],[0.575,0.745],[0.269,0.752],[0.264,0.747],[-0.353,0.752],[-0.357,0.747],[-0.979,0.752],[-0.983,0.747],[-1.6,0.752],[-1.604,0.747],[-2.281,0.748],[-2.302,0.739],[-2.351,0.703],[-2.373,0.653],[-2.375,0.629],[-2.402,0.682],[-2.439,0.715],[-2.464,0.723],[-3.107,0.723],[-3.153,0.702]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"x":"half_length"}}},"bounds":{"min":[0,-0.75,-0.75],"max":[6.4,0.75,0.75]},"volume_in3":8.1043,"centroid":[3.6461,0,-0.0005],"shell":[2.8898,-0.0036,0.005],"area_in2":50.3041,"triangles":26136,"manifold":true,"slabs":[[0,-0.75,-0.75,6.4,0.75,0.75]],"slots":["body","ring","latch","collar"]},"surefire-warcomp":{"part":"surefire-warcomp","model":"surefire-warcomp.glb","script":"surefire_warcomp.py","inputs":{"surefire-warcomp.body_od":0.839,"surefire-warcomp.bore_d":0.244,"surefire-warcomp.boss_length":0.213,"surefire-warcomp.boss_od":0.678,"surefire-warcomp.collar_front_x":1.019,"surefire-warcomp.collar_od":0.869,"surefire-warcomp.cone_length":0.06,"surefire-warcomp.flange_length":0.143,"surefire-warcomp.flats":0,"surefire-warcomp.length":2.718,"surefire-warcomp.nose_r":0.079,"surefire-warcomp.od":0.947,"surefire-warcomp.overall_length":2.7,"surefire-warcomp.pocket_floor_d":0.817,"surefire-warcomp.pocket_front_x":0.543,"surefire-warcomp.pocket_rear_x":0.282,"surefire-warcomp.pocket_width":0.114,"surefire-warcomp.port_center_angle":47,"surefire-warcomp.port_column_pitch":26,"surefire-warcomp.port_columns":6,"surefire-warcomp.port_d":0.159,"surefire-warcomp.port_group_gap":35,"surefire-warcomp.port_row_1_x":0.596,"surefire-warcomp.port_row_pitch":0.206,"surefire-warcomp.port_rows":2,"surefire-warcomp.shim_stack":0.018,"surefire-warcomp.slot_root_r":0.04,"surefire-warcomp.slot_root_x":1.13,"surefire-warcomp.slot_width":0.285,"surefire-warcomp.step_front_od":0.824,"surefire-warcomp.step_x":2.09,"surefire-warcomp.tab_front_x":0.468,"surefire-warcomp.tab_width":0.136,"surefire-warcomp.thread_depth":0.69,"surefire-warcomp.thread_major_d":0.4957,"surefire-warcomp.thread_minor_d":0.4551,"surefire-warcomp.thread_pitch":0.03571,"surefire-warcomp.tines":3},"profiles":{},"bounds":{"min":[0,-0.4735,-0.4735],"max":[2.718,0.4735,0.4735]},"volume_in3":0.7965,"centroid":[1.2213,-0.0093,-0.0104],"shell":[1.1793,0.0066,0.0086],"area_in2":12.784,"triangles":20986,"manifold":true,"slabs":[[0,-0.474,-0.474,1.165,0.474,0.474],[1.165,-0.419,-0.419,2.718,0.397,0.419]],"slots":["body","shims"]},"sylvan-arms-sa5-pro-left-folder.carrier_extension":{"part":"sylvan-arms-sa5-pro-left-folder","component":"carrier_extension","model":"sylvan-arms-sa5-pro-left-folder.carrier_extension.glb","script":"sylvan_arms_sa5_pro.py","inputs":{"std.ar15.receiver_rear_x":-1.125,"std.ar15.upper_rear_face_x":-0.621,"std.receiver_extension.bore_d":1,"std.receiver_extension.front_face_x":-0.669,"std.receiver_extension.thread_major_d":1.1813,"std.receiver_extension.thread_minor_d":1.1093,"std.receiver_extension.thread_pitch":0.0625,"sylvan-arms-sa5-pro-left-folder.added_length":1.475,"sylvan-arms-sa5-pro-left-folder.big_hole_d":0.505,"sylvan-arms-sa5-pro-left-folder.big_hole_depth":0.4,"sylvan-arms-sa5-pro-left-folder.block_top_below_axis":0.217,"sylvan-arms-sa5-pro-left-folder.body_bottom_below_axis":1.421,"sylvan-arms-sa5-pro-left-folder.bolt_head_d":0.26,"sylvan-arms-sa5-pro-left-folder.bolt_head_height":0.08,"sylvan-arms-sa5-pro-left-folder.bolt_head_recess":0.02,"sylvan-arms-sa5-pro-left-folder.bolt_socket":0.1,"sylvan-arms-sa5-pro-left-folder.bolt_socket_depth":0.06,"sylvan-arms-sa5-pro-left-folder.bore_thread_crest_d":1.1453,"sylvan-arms-sa5-pro-left-folder.button_behind_front":0.39,"sylvan-arms-sa5-pro-left-folder.button_below_axis":0.68,"sylvan-arms-sa5-pro-left-folder.button_d":0.28,"sylvan-arms-sa5-pro-left-folder.button_proud":0.06,"sylvan-arms-sa5-pro-left-folder.collar_bottom_below_axis":1.109,"sylvan-arms-sa5-pro-left-folder.corner_r":0.3,"sylvan-arms-sa5-pro-left-folder.ext_body_d":0.737,"sylvan-arms-sa5-pro-left-folder.ext_body_length":0.743,"sylvan-arms-sa5-pro-left-folder.ext_flare_length":0.157,"sylvan-arms-sa5-pro-left-folder.ext_foot_d":0.61,"sylvan-arms-sa5-pro-left-folder.ext_foot_length":0.062,"sylvan-arms-sa5-pro-left-folder.ext_groove_1":0.105,"sylvan-arms-sa5-pro-left-folder.ext_groove_2":0.314,"sylvan-arms-sa5-pro-left-folder.ext_groove_depth":0.025,"sylvan-arms-sa5-pro-left-folder.ext_groove_w":0.045,"sylvan-arms-sa5-pro-left-folder.ext_neck_d":0.488,"sylvan-arms-sa5-pro-left-folder.ext_neck_length":0.513,"sylvan-arms-sa5-pro-left-folder.ext_pilot_d":0.61,"sylvan-arms-sa5-pro-left-folder.ext_pilot_length":0.512,"sylvan-arms-sa5-pro-left-folder.face_hole_depth":0.25,"sylvan-arms-sa5-pro-left-folder.hinge_x":1.914,"sylvan-arms-sa5-pro-left-folder.hinge_z":1.232,"sylvan-arms-sa5-pro-left-folder.knuckle_d":0.505,"sylvan-arms-sa5-pro-left-folder.lobe_centre_below_axis":1.045,"sylvan-arms-sa5-pro-left-folder.lobe_r":0.37,"sylvan-arms-sa5-pro-left-folder.mid_hole_apart":0.334,"sylvan-arms-sa5-pro-left-folder.mid_hole_below_axis":0.745,"sylvan-arms-sa5-pro-left-folder.mid_hole_d":0.274,"sylvan-arms-sa5-pro-left-folder.mid_hole_depth":0.25,"sylvan-arms-sa5-pro-left-folder.nut_d":1.42,"sylvan-arms-sa5-pro-left-folder.nut_length":0.221,"sylvan-arms-sa5-pro-left-folder.nut_notch_depth":0.06,"sylvan-arms-sa5-pro-left-folder.nut_notch_width":0.14,"sylvan-arms-sa5-pro-left-folder.nut_notches":4,"sylvan-arms-sa5-pro-left-folder.plate_bottom_below_axis":0.8,"sylvan-arms-sa5-pro-left-folder.plate_front":0.134,"sylvan-arms-sa5-pro-left-folder.plate_length":0.42,"sylvan-arms-sa5-pro-left-folder.plate_proud":0.03,"sylvan-arms-sa5-pro-left-folder.plate_top":0.06,"sylvan-arms-sa5-pro-left-folder.qd_behind_front":0.45,"sylvan-arms-sa5-pro-left-folder.qd_below_axis":1.2,"sylvan-arms-sa5-pro-left-folder.qd_bore_d":0.31,"sylvan-arms-sa5-pro-left-folder.qd_d":0.44,"sylvan-arms-sa5-pro-left-folder.qd_depth":0.3,"sylvan-arms-sa5-pro-left-folder.qd_proud":0.2,"sylvan-arms-sa5-pro-left-folder.rear_hex_below_axis":1.083,"sylvan-arms-sa5-pro-left-folder.rear_hex_d":0.26,"sylvan-arms-sa5-pro-left-folder.rear_hex_out":0.065,"sylvan-arms-sa5-pro-left-folder.rear_hole_below_axis":1.03,"sylvan-arms-sa5-pro-left-folder.rear_hole_d":0.21,"sylvan-arms-sa5-pro-left-folder.rear_hole_in":0.371,"sylvan-arms-sa5-pro-left-folder.rear_screw_below_axis":0.441,"sylvan-arms-sa5-pro-left-folder.rear_screw_d":0.19,"sylvan-arms-sa5-pro-left-folder.rear_screw_out":0.578,"sylvan-arms-sa5-pro-left-folder.receiver_bore_d":1.079,"sylvan-arms-sa5-pro-left-folder.receiver_half_length":0.568,"sylvan-arms-sa5-pro-left-folder.ring_r":0.737,"sylvan-arms-sa5-pro-left-folder.slot_below_axis":0.79,"sylvan-arms-sa5-pro-left-folder.slot_out":0.43,"sylvan-arms-sa5-pro-left-folder.small_hole_below_axis":0.718,"sylvan-arms-sa5-pro-left-folder.small_hole_d":0.124,"sylvan-arms-sa5-pro-left-folder.small_hole_left":0.098,"sylvan-arms-sa5-pro-left-folder.stock_block_length":0.5,"sylvan-arms-sa5-pro-left-folder.stock_half_length":0.686,"sylvan-arms-sa5-pro-left-folder.tab_below_axis":0.721,"sylvan-arms-sa5-pro-left-folder.tab_height":0.39,"sylvan-arms-sa5-pro-left-folder.tab_out":0.351,"sylvan-arms-sa5-pro-left-folder.tab_proud":0.17,"sylvan-arms-sa5-pro-left-folder.tab_width":0.16,"sylvan-arms-sa5-pro-left-folder.top_knuckle_bottom_below_axis":0.579},"profiles":{},"features":{},"placement":{},"bounds":{"min":[0.109,-0.3685,-0.3685],"max":[2.096,0.3685,0.3685]},"volume_in3":0.6125,"centroid":[1.0296,0,0],"shell":[1.0663,0,0],"area_in2":4.9517,"triangles":8448,"manifold":true,"slabs":[[0.109,-0.305,-0.305,0.506,0.305,0.305],[0.506,-0.368,-0.368,1.699,0.368,0.368],[1.699,-0.305,-0.305,2.096,0.305,0.305]],"slots":["hardware"]},"sylvan-arms-sa5-pro-left-folder.receiver_half":{"part":"sylvan-arms-sa5-pro-left-folder","component":"receiver_half","model":"sylvan-arms-sa5-pro-left-folder.receiver_half.glb","script":"sylvan_arms_sa5_pro.py","inputs":{"std.ar15.receiver_rear_x":-1.125,"std.receiver_extension.bore_d":1,"std.receiver_extension.front_face_x":-0.669,"std.receiver_extension.thread_major_d":1.1813,"std.receiver_extension.thread_minor_d":1.1093,"std.receiver_extension.thread_pitch":0.0625,"sylvan-arms-sa5-pro-left-folder.added_length":1.475,"sylvan-arms-sa5-pro-left-folder.block_top_below_axis":0.217,"sylvan-arms-sa5-pro-left-folder.body_bottom_below_axis":1.421,"sylvan-arms-sa5-pro-left-folder.bolt_head_d":0.26,"sylvan-arms-sa5-pro-left-folder.bolt_head_height":0.08,"sylvan-arms-sa5-pro-left-folder.bolt_head_recess":0.02,"sylvan-arms-sa5-pro-left-folder.bolt_socket":0.1,"sylvan-arms-sa5-pro-left-folder.bolt_socket_depth":0.06,"sylvan-arms-sa5-pro-left-folder.button_behind_front":0.39,"sylvan-arms-sa5-pro-left-folder.button_below_axis":0.68,"sylvan-arms-sa5-pro-left-folder.button_d":0.28,"sylvan-arms-sa5-pro-left-folder.button_proud":0.06,"sylvan-arms-sa5-pro-left-folder.collar_bottom_below_axis":1.109,"sylvan-arms-sa5-pro-left-folder.corner_r":0.3,"sylvan-arms-sa5-pro-left-folder.face_hole_depth":0.25,"sylvan-arms-sa5-pro-left-folder.hinge_x":1.914,"sylvan-arms-sa5-pro-left-folder.hinge_z":1.232,"sylvan-arms-sa5-pro-left-folder.knuckle_d":0.505,"sylvan-arms-sa5-pro-left-folder.nut_d":1.42,"sylvan-arms-sa5-pro-left-folder.nut_length":0.221,"sylvan-arms-sa5-pro-left-folder.nut_notch_depth":0.06,"sylvan-arms-sa5-pro-left-folder.nut_notch_width":0.14,"sylvan-arms-sa5-pro-left-folder.nut_notches":4,"sylvan-arms-sa5-pro-left-folder.plate_bottom_below_axis":0.8,"sylvan-arms-sa5-pro-left-folder.plate_front":0.134,"sylvan-arms-sa5-pro-left-folder.plate_length":0.42,"sylvan-arms-sa5-pro-left-folder.plate_proud":0.03,"sylvan-arms-sa5-pro-left-folder.plate_top":0.06,"sylvan-arms-sa5-pro-left-folder.qd_behind_front":0.45,"sylvan-arms-sa5-pro-left-folder.qd_below_axis":1.2,"sylvan-arms-sa5-pro-left-folder.qd_bore_d":0.31,"sylvan-arms-sa5-pro-left-folder.qd_d":0.44,"sylvan-arms-sa5-pro-left-folder.qd_depth":0.3,"sylvan-arms-sa5-pro-left-folder.qd_proud":0.2,"sylvan-arms-sa5-pro-left-folder.rear_hex_below_axis":1.083,"sylvan-arms-sa5-pro-left-folder.rear_hex_d":0.26,"sylvan-arms-sa5-pro-left-folder.rear_hex_out":0.065,"sylvan-arms-sa5-pro-left-folder.rear_hole_below_axis":1.03,"sylvan-arms-sa5-pro-left-folder.rear_hole_d":0.21,"sylvan-arms-sa5-pro-left-folder.rear_hole_in":0.371,"sylvan-arms-sa5-pro-left-folder.rear_screw_below_axis":0.441,"sylvan-arms-sa5-pro-left-folder.rear_screw_d":0.19,"sylvan-arms-sa5-pro-left-folder.rear_screw_out":0.578,"sylvan-arms-sa5-pro-left-folder.receiver_bore_d":1.079,"sylvan-arms-sa5-pro-left-folder.receiver_half_length":0.568,"sylvan-arms-sa5-pro-left-folder.ring_r":0.737,"sylvan-arms-sa5-pro-left-folder.slot_below_axis":0.79,"sylvan-arms-sa5-pro-left-folder.slot_out":0.43,"sylvan-arms-sa5-pro-left-folder.stock_half_length":0.686,"sylvan-arms-sa5-pro-left-folder.tab_below_axis":0.721,"sylvan-arms-sa5-pro-left-folder.tab_height":0.39,"sylvan-arms-sa5-pro-left-folder.tab_out":0.351,"sylvan-arms-sa5-pro-left-folder.tab_proud":0.17,"sylvan-arms-sa5-pro-left-folder.tab_width":0.16,"sylvan-arms-sa5-pro-left-folder.top_knuckle_bottom_below_axis":0.579},"profiles":{},"features":{},"placement":{},"bounds":{"min":[0.669,-1.421,-0.937],"max":[2.1665,0.737,1.4845]},"volume_in3":1.803,"centroid":[1.5599,-0.5454,0.233],"shell":[1.451,-0.3445,0.125],"area_in2":23.5464,"triangles":28894,"manifold":true,"slabs":[[1.125,-1.42,-0.937,2.016,0.44,-0.591],[0.669,-1.421,-0.591,1.914,0.737,0.447],[0.669,-1.421,0.447,1.914,0.586,0.793],[1.346,-1.421,0.793,2.167,-0.217,1.484]],"slots":["body","hardware"]},"sylvan-arms-sa5-pro-left-folder.stock_half":{"part":"sylvan-arms-sa5-pro-left-folder","component":"stock_half","model":"sylvan-arms-sa5-pro-left-folder.stock_half.glb","script":"sylvan_arms_sa5_pro.py","inputs":{"std.ar15.receiver_rear_x":-1.125,"std.receiver_extension.bore_d":1,"std.receiver_extension.front_face_x":-0.669,"std.receiver_extension.thread_major_d":1.1813,"std.receiver_extension.thread_minor_d":1.1093,"std.receiver_extension.thread_pitch":0.0625,"sylvan-arms-sa5-pro-left-folder.added_length":1.475,"sylvan-arms-sa5-pro-left-folder.big_hole_d":0.505,"sylvan-arms-sa5-pro-left-folder.big_hole_depth":0.4,"sylvan-arms-sa5-pro-left-folder.block_top_below_axis":0.217,"sylvan-arms-sa5-pro-left-folder.body_bottom_below_axis":1.421,"sylvan-arms-sa5-pro-left-folder.bolt_head_d":0.26,"sylvan-arms-sa5-pro-left-folder.bolt_head_height":0.08,"sylvan-arms-sa5-pro-left-folder.bolt_head_recess":0.02,"sylvan-arms-sa5-pro-left-folder.bolt_socket":0.1,"sylvan-arms-sa5-pro-left-folder.bolt_socket_depth":0.06,"sylvan-arms-sa5-pro-left-folder.bore_thread_crest_d":1.1453,"sylvan-arms-sa5-pro-left-folder.button_behind_front":0.39,"sylvan-arms-sa5-pro-left-folder.button_below_axis":0.68,"sylvan-arms-sa5-pro-left-folder.button_d":0.28,"sylvan-arms-sa5-pro-left-folder.button_proud":0.06,"sylvan-arms-sa5-pro-left-folder.collar_bottom_below_axis":1.109,"sylvan-arms-sa5-pro-left-folder.corner_r":0.3,"sylvan-arms-sa5-pro-left-folder.face_hole_depth":0.25,"sylvan-arms-sa5-pro-left-folder.hinge_x":1.914,"sylvan-arms-sa5-pro-left-folder.hinge_z":1.232,"sylvan-arms-sa5-pro-left-folder.knuckle_d":0.505,"sylvan-arms-sa5-pro-left-folder.lobe_centre_below_axis":1.045,"sylvan-arms-sa5-pro-left-folder.lobe_r":0.37,"sylvan-arms-sa5-pro-left-folder.mid_hole_apart":0.334,"sylvan-arms-sa5-pro-left-folder.mid_hole_below_axis":0.745,"sylvan-arms-sa5-pro-left-folder.mid_hole_d":0.274,"sylvan-arms-sa5-pro-left-folder.mid_hole_depth":0.25,"sylvan-arms-sa5-pro-left-folder.nut_d":1.42,"sylvan-arms-sa5-pro-left-folder.nut_length":0.221,"sylvan-arms-sa5-pro-left-folder.nut_notch_depth":0.06,"sylvan-arms-sa5-pro-left-folder.nut_notch_width":0.14,"sylvan-arms-sa5-pro-left-folder.nut_notches":4,"sylvan-arms-sa5-pro-left-folder.plate_bottom_below_axis":0.8,"sylvan-arms-sa5-pro-left-folder.plate_front":0.134,"sylvan-arms-sa5-pro-left-folder.plate_length":0.42,"sylvan-arms-sa5-pro-left-folder.plate_proud":0.03,"sylvan-arms-sa5-pro-left-folder.plate_top":0.06,"sylvan-arms-sa5-pro-left-folder.qd_behind_front":0.45,"sylvan-arms-sa5-pro-left-folder.qd_below_axis":1.2,"sylvan-arms-sa5-pro-left-folder.qd_bore_d":0.31,"sylvan-arms-sa5-pro-left-folder.qd_d":0.44,"sylvan-arms-sa5-pro-left-folder.qd_depth":0.3,"sylvan-arms-sa5-pro-left-folder.qd_proud":0.2,"sylvan-arms-sa5-pro-left-folder.rear_hex_below_axis":1.083,"sylvan-arms-sa5-pro-left-folder.rear_hex_d":0.26,"sylvan-arms-sa5-pro-left-folder.rear_hex_out":0.065,"sylvan-arms-sa5-pro-left-folder.rear_hole_below_axis":1.03,"sylvan-arms-sa5-pro-left-folder.rear_hole_d":0.21,"sylvan-arms-sa5-pro-left-folder.rear_hole_in":0.371,"sylvan-arms-sa5-pro-left-folder.rear_screw_below_axis":0.441,"sylvan-arms-sa5-pro-left-folder.rear_screw_d":0.19,"sylvan-arms-sa5-pro-left-folder.rear_screw_out":0.578,"sylvan-arms-sa5-pro-left-folder.receiver_bore_d":1.079,"sylvan-arms-sa5-pro-left-folder.receiver_half_length":0.568,"sylvan-arms-sa5-pro-left-folder.ring_r":0.737,"sylvan-arms-sa5-pro-left-folder.slot_below_axis":0.79,"sylvan-arms-sa5-pro-left-folder.slot_out":0.43,"sylvan-arms-sa5-pro-left-folder.small_hole_below_axis":0.718,"sylvan-arms-sa5-pro-left-folder.small_hole_d":0.124,"sylvan-arms-sa5-pro-left-folder.small_hole_left":0.098,"sylvan-arms-sa5-pro-left-folder.stock_block_length":0.5,"sylvan-arms-sa5-pro-left-folder.stock_half_length":0.686,"sylvan-arms-sa5-pro-left-folder.tab_below_axis":0.721,"sylvan-arms-sa5-pro-left-folder.tab_height":0.39,"sylvan-arms-sa5-pro-left-folder.tab_out":0.351,"sylvan-arms-sa5-pro-left-folder.tab_proud":0.17,"sylvan-arms-sa5-pro-left-folder.tab_width":0.16,"sylvan-arms-sa5-pro-left-folder.top_knuckle_bottom_below_axis":0.579},"profiles":{},"features":{},"placement":{},"bounds":{"min":[1.6615,-1.421,-0.737],"max":[2.6,0.737,1.4845]},"volume_in3":1.3601,"centroid":[2.1873,-0.6159,0.268],"shell":[2.2126,-0.4853,0.2277],"area_in2":14.8878,"triangles":20214,"manifold":true,"slabs":[[1.744,-1.421,-0.737,2.6,0.639,-0.367],[1.744,-1.421,-0.367,2.6,0.737,0.003],[1.914,-1.421,0.003,2.6,0.737,0.374],[1.914,-1.421,0.374,2.6,0.635,0.744],[1.661,-1.421,0.744,2.414,-0.217,1.484]],"slots":["body","hardware"]},"sylvan-arms-sa5-pro-right-folder.carrier_extension":{"part":"sylvan-arms-sa5-pro-right-folder","component":"carrier_extension","model":"sylvan-arms-sa5-pro-right-folder.carrier_extension.glb","script":"sylvan_arms_sa5_pro.py","inputs":{"std.ar15.receiver_rear_x":-1.125,"std.ar15.upper_rear_face_x":-0.621,"std.receiver_extension.bore_d":1,"std.receiver_extension.front_face_x":-0.669,"std.receiver_extension.thread_major_d":1.1813,"std.receiver_extension.thread_minor_d":1.1093,"std.receiver_extension.thread_pitch":0.0625,"sylvan-arms-sa5-pro-left-folder.added_length":1.475,"sylvan-arms-sa5-pro-left-folder.big_hole_d":0.505,"sylvan-arms-sa5-pro-left-folder.big_hole_depth":0.4,"sylvan-arms-sa5-pro-left-folder.block_top_below_axis":0.217,"sylvan-arms-sa5-pro-left-folder.body_bottom_below_axis":1.421,"sylvan-arms-sa5-pro-left-folder.bolt_head_d":0.26,"sylvan-arms-sa5-pro-left-folder.bolt_head_height":0.08,"sylvan-arms-sa5-pro-left-folder.bolt_head_recess":0.02,"sylvan-arms-sa5-pro-left-folder.bolt_socket":0.1,"sylvan-arms-sa5-pro-left-folder.bolt_socket_depth":0.06,"sylvan-arms-sa5-pro-left-folder.bore_thread_crest_d":1.1453,"sylvan-arms-sa5-pro-left-folder.button_behind_front":0.39,"sylvan-arms-sa5-pro-left-folder.button_below_axis":0.68,"sylvan-arms-sa5-pro-left-folder.button_d":0.28,"sylvan-arms-sa5-pro-left-folder.button_proud":0.06,"sylvan-arms-sa5-pro-left-folder.collar_bottom_below_axis":1.109,"sylvan-arms-sa5-pro-left-folder.corner_r":0.3,"sylvan-arms-sa5-pro-left-folder.ext_body_d":0.737,"sylvan-arms-sa5-pro-left-folder.ext_body_length":0.743,"sylvan-arms-sa5-pro-left-folder.ext_flare_length":0.157,"sylvan-arms-sa5-pro-left-folder.ext_foot_d":0.61,"sylvan-arms-sa5-pro-left-folder.ext_foot_length":0.062,"sylvan-arms-sa5-pro-left-folder.ext_groove_1":0.105,"sylvan-arms-sa5-pro-left-folder.ext_groove_2":0.314,"sylvan-arms-sa5-pro-left-folder.ext_groove_depth":0.025,"sylvan-arms-sa5-pro-left-folder.ext_groove_w":0.045,"sylvan-arms-sa5-pro-left-folder.ext_neck_d":0.488,"sylvan-arms-sa5-pro-left-folder.ext_neck_length":0.513,"sylvan-arms-sa5-pro-left-folder.ext_pilot_d":0.61,"sylvan-arms-sa5-pro-left-folder.ext_pilot_length":0.512,"sylvan-arms-sa5-pro-left-folder.face_hole_depth":0.25,"sylvan-arms-sa5-pro-left-folder.hinge_x":1.914,"sylvan-arms-sa5-pro-left-folder.hinge_z":1.232,"sylvan-arms-sa5-pro-left-folder.knuckle_d":0.505,"sylvan-arms-sa5-pro-left-folder.lobe_centre_below_axis":1.045,"sylvan-arms-sa5-pro-left-folder.lobe_r":0.37,"sylvan-arms-sa5-pro-left-folder.mid_hole_apart":0.334,"sylvan-arms-sa5-pro-left-folder.mid_hole_below_axis":0.745,"sylvan-arms-sa5-pro-left-folder.mid_hole_d":0.274,"sylvan-arms-sa5-pro-left-folder.mid_hole_depth":0.25,"sylvan-arms-sa5-pro-left-folder.nut_d":1.42,"sylvan-arms-sa5-pro-left-folder.nut_length":0.221,"sylvan-arms-sa5-pro-left-folder.nut_notch_depth":0.06,"sylvan-arms-sa5-pro-left-folder.nut_notch_width":0.14,"sylvan-arms-sa5-pro-left-folder.nut_notches":4,"sylvan-arms-sa5-pro-left-folder.plate_bottom_below_axis":0.8,"sylvan-arms-sa5-pro-left-folder.plate_front":0.134,"sylvan-arms-sa5-pro-left-folder.plate_length":0.42,"sylvan-arms-sa5-pro-left-folder.plate_proud":0.03,"sylvan-arms-sa5-pro-left-folder.plate_top":0.06,"sylvan-arms-sa5-pro-left-folder.qd_behind_front":0.45,"sylvan-arms-sa5-pro-left-folder.qd_below_axis":1.2,"sylvan-arms-sa5-pro-left-folder.qd_bore_d":0.31,"sylvan-arms-sa5-pro-left-folder.qd_d":0.44,"sylvan-arms-sa5-pro-left-folder.qd_depth":0.3,"sylvan-arms-sa5-pro-left-folder.qd_proud":0.2,"sylvan-arms-sa5-pro-left-folder.rear_hex_below_axis":1.083,"sylvan-arms-sa5-pro-left-folder.rear_hex_d":0.26,"sylvan-arms-sa5-pro-left-folder.rear_hex_out":0.065,"sylvan-arms-sa5-pro-left-folder.rear_hole_below_axis":1.03,"sylvan-arms-sa5-pro-left-folder.rear_hole_d":0.21,"sylvan-arms-sa5-pro-left-folder.rear_hole_in":0.371,"sylvan-arms-sa5-pro-left-folder.rear_screw_below_axis":0.441,"sylvan-arms-sa5-pro-left-folder.rear_screw_d":0.19,"sylvan-arms-sa5-pro-left-folder.rear_screw_out":0.578,"sylvan-arms-sa5-pro-left-folder.receiver_bore_d":1.079,"sylvan-arms-sa5-pro-left-folder.receiver_half_length":0.568,"sylvan-arms-sa5-pro-left-folder.ring_r":0.737,"sylvan-arms-sa5-pro-left-folder.slot_below_axis":0.79,"sylvan-arms-sa5-pro-left-folder.slot_out":0.43,"sylvan-arms-sa5-pro-left-folder.small_hole_below_axis":0.718,"sylvan-arms-sa5-pro-left-folder.small_hole_d":0.124,"sylvan-arms-sa5-pro-left-folder.small_hole_left":0.098,"sylvan-arms-sa5-pro-left-folder.stock_block_length":0.5,"sylvan-arms-sa5-pro-left-folder.stock_half_length":0.686,"sylvan-arms-sa5-pro-left-folder.tab_below_axis":0.721,"sylvan-arms-sa5-pro-left-folder.tab_height":0.39,"sylvan-arms-sa5-pro-left-folder.tab_out":0.351,"sylvan-arms-sa5-pro-left-folder.tab_proud":0.17,"sylvan-arms-sa5-pro-left-folder.tab_width":0.16,"sylvan-arms-sa5-pro-left-folder.top_knuckle_bottom_below_axis":0.579},"profiles":{},"features":{},"placement":{},"bounds":{"min":[0.109,-0.3685,-0.3685],"max":[2.096,0.3685,0.3685]},"volume_in3":0.6125,"centroid":[1.0296,0,0],"shell":[1.0663,0,0],"area_in2":4.9517,"triangles":8448,"manifold":true,"slabs":[[0.109,-0.305,-0.305,0.506,0.305,0.305],[0.506,-0.368,-0.368,1.699,0.368,0.368],[1.699,-0.305,-0.305,2.096,0.305,0.305]],"slots":["hardware"]},"sylvan-arms-sa5-pro-right-folder.receiver_half":{"part":"sylvan-arms-sa5-pro-right-folder","component":"receiver_half","model":"sylvan-arms-sa5-pro-right-folder.receiver_half.glb","script":"sylvan_arms_sa5_pro.py","inputs":{"std.ar15.receiver_rear_x":-1.125,"std.receiver_extension.bore_d":1,"std.receiver_extension.front_face_x":-0.669,"std.receiver_extension.thread_major_d":1.1813,"std.receiver_extension.thread_minor_d":1.1093,"std.receiver_extension.thread_pitch":0.0625,"sylvan-arms-sa5-pro-left-folder.added_length":1.475,"sylvan-arms-sa5-pro-left-folder.block_top_below_axis":0.217,"sylvan-arms-sa5-pro-left-folder.body_bottom_below_axis":1.421,"sylvan-arms-sa5-pro-left-folder.bolt_head_d":0.26,"sylvan-arms-sa5-pro-left-folder.bolt_head_height":0.08,"sylvan-arms-sa5-pro-left-folder.bolt_head_recess":0.02,"sylvan-arms-sa5-pro-left-folder.bolt_socket":0.1,"sylvan-arms-sa5-pro-left-folder.bolt_socket_depth":0.06,"sylvan-arms-sa5-pro-left-folder.button_behind_front":0.39,"sylvan-arms-sa5-pro-left-folder.button_below_axis":0.68,"sylvan-arms-sa5-pro-left-folder.button_d":0.28,"sylvan-arms-sa5-pro-left-folder.button_proud":0.06,"sylvan-arms-sa5-pro-left-folder.collar_bottom_below_axis":1.109,"sylvan-arms-sa5-pro-left-folder.corner_r":0.3,"sylvan-arms-sa5-pro-left-folder.face_hole_depth":0.25,"sylvan-arms-sa5-pro-left-folder.hinge_x":1.914,"sylvan-arms-sa5-pro-left-folder.hinge_z":1.232,"sylvan-arms-sa5-pro-left-folder.knuckle_d":0.505,"sylvan-arms-sa5-pro-left-folder.nut_d":1.42,"sylvan-arms-sa5-pro-left-folder.nut_length":0.221,"sylvan-arms-sa5-pro-left-folder.nut_notch_depth":0.06,"sylvan-arms-sa5-pro-left-folder.nut_notch_width":0.14,"sylvan-arms-sa5-pro-left-folder.nut_notches":4,"sylvan-arms-sa5-pro-left-folder.plate_bottom_below_axis":0.8,"sylvan-arms-sa5-pro-left-folder.plate_front":0.134,"sylvan-arms-sa5-pro-left-folder.plate_length":0.42,"sylvan-arms-sa5-pro-left-folder.plate_proud":0.03,"sylvan-arms-sa5-pro-left-folder.plate_top":0.06,"sylvan-arms-sa5-pro-left-folder.qd_behind_front":0.45,"sylvan-arms-sa5-pro-left-folder.qd_below_axis":1.2,"sylvan-arms-sa5-pro-left-folder.qd_bore_d":0.31,"sylvan-arms-sa5-pro-left-folder.qd_d":0.44,"sylvan-arms-sa5-pro-left-folder.qd_depth":0.3,"sylvan-arms-sa5-pro-left-folder.qd_proud":0.2,"sylvan-arms-sa5-pro-left-folder.rear_hex_below_axis":1.083,"sylvan-arms-sa5-pro-left-folder.rear_hex_d":0.26,"sylvan-arms-sa5-pro-left-folder.rear_hex_out":0.065,"sylvan-arms-sa5-pro-left-folder.rear_hole_below_axis":1.03,"sylvan-arms-sa5-pro-left-folder.rear_hole_d":0.21,"sylvan-arms-sa5-pro-left-folder.rear_hole_in":0.371,"sylvan-arms-sa5-pro-left-folder.rear_screw_below_axis":0.441,"sylvan-arms-sa5-pro-left-folder.rear_screw_d":0.19,"sylvan-arms-sa5-pro-left-folder.rear_screw_out":0.578,"sylvan-arms-sa5-pro-left-folder.receiver_bore_d":1.079,"sylvan-arms-sa5-pro-left-folder.receiver_half_length":0.568,"sylvan-arms-sa5-pro-left-folder.ring_r":0.737,"sylvan-arms-sa5-pro-left-folder.slot_below_axis":0.79,"sylvan-arms-sa5-pro-left-folder.slot_out":0.43,"sylvan-arms-sa5-pro-left-folder.stock_half_length":0.686,"sylvan-arms-sa5-pro-left-folder.tab_below_axis":0.721,"sylvan-arms-sa5-pro-left-folder.tab_height":0.39,"sylvan-arms-sa5-pro-left-folder.tab_out":0.351,"sylvan-arms-sa5-pro-left-folder.tab_proud":0.17,"sylvan-arms-sa5-pro-left-folder.tab_width":0.16,"sylvan-arms-sa5-pro-left-folder.top_knuckle_bottom_below_axis":0.579},"profiles":{},"features":{},"placement":{},"bounds":{"min":[0.669,-1.421,-1.4845],"max":[2.1665,0.737,0.937]},"volume_in3":1.803,"centroid":[1.5599,-0.5454,-0.233],"shell":[1.451,-0.3445,-0.125],"area_in2":23.5464,"triangles":28894,"manifold":true,"slabs":[[1.346,-1.421,-1.484,2.167,-0.217,-0.793],[0.669,-1.421,-0.793,1.914,0.586,-0.447],[0.669,-1.421,-0.447,1.914,0.737,0.591],[1.125,-1.42,0.591,2.016,0.44,0.937]],"slots":["body","hardware"]},"sylvan-arms-sa5-pro-right-folder.stock_half":{"part":"sylvan-arms-sa5-pro-right-folder","component":"stock_half","model":"sylvan-arms-sa5-pro-right-folder.stock_half.glb","script":"sylvan_arms_sa5_pro.py","inputs":{"std.ar15.receiver_rear_x":-1.125,"std.receiver_extension.bore_d":1,"std.receiver_extension.front_face_x":-0.669,"std.receiver_extension.thread_major_d":1.1813,"std.receiver_extension.thread_minor_d":1.1093,"std.receiver_extension.thread_pitch":0.0625,"sylvan-arms-sa5-pro-left-folder.added_length":1.475,"sylvan-arms-sa5-pro-left-folder.big_hole_d":0.505,"sylvan-arms-sa5-pro-left-folder.big_hole_depth":0.4,"sylvan-arms-sa5-pro-left-folder.block_top_below_axis":0.217,"sylvan-arms-sa5-pro-left-folder.body_bottom_below_axis":1.421,"sylvan-arms-sa5-pro-left-folder.bolt_head_d":0.26,"sylvan-arms-sa5-pro-left-folder.bolt_head_height":0.08,"sylvan-arms-sa5-pro-left-folder.bolt_head_recess":0.02,"sylvan-arms-sa5-pro-left-folder.bolt_socket":0.1,"sylvan-arms-sa5-pro-left-folder.bolt_socket_depth":0.06,"sylvan-arms-sa5-pro-left-folder.bore_thread_crest_d":1.1453,"sylvan-arms-sa5-pro-left-folder.button_behind_front":0.39,"sylvan-arms-sa5-pro-left-folder.button_below_axis":0.68,"sylvan-arms-sa5-pro-left-folder.button_d":0.28,"sylvan-arms-sa5-pro-left-folder.button_proud":0.06,"sylvan-arms-sa5-pro-left-folder.collar_bottom_below_axis":1.109,"sylvan-arms-sa5-pro-left-folder.corner_r":0.3,"sylvan-arms-sa5-pro-left-folder.face_hole_depth":0.25,"sylvan-arms-sa5-pro-left-folder.hinge_x":1.914,"sylvan-arms-sa5-pro-left-folder.hinge_z":1.232,"sylvan-arms-sa5-pro-left-folder.knuckle_d":0.505,"sylvan-arms-sa5-pro-left-folder.lobe_centre_below_axis":1.045,"sylvan-arms-sa5-pro-left-folder.lobe_r":0.37,"sylvan-arms-sa5-pro-left-folder.mid_hole_apart":0.334,"sylvan-arms-sa5-pro-left-folder.mid_hole_below_axis":0.745,"sylvan-arms-sa5-pro-left-folder.mid_hole_d":0.274,"sylvan-arms-sa5-pro-left-folder.mid_hole_depth":0.25,"sylvan-arms-sa5-pro-left-folder.nut_d":1.42,"sylvan-arms-sa5-pro-left-folder.nut_length":0.221,"sylvan-arms-sa5-pro-left-folder.nut_notch_depth":0.06,"sylvan-arms-sa5-pro-left-folder.nut_notch_width":0.14,"sylvan-arms-sa5-pro-left-folder.nut_notches":4,"sylvan-arms-sa5-pro-left-folder.plate_bottom_below_axis":0.8,"sylvan-arms-sa5-pro-left-folder.plate_front":0.134,"sylvan-arms-sa5-pro-left-folder.plate_length":0.42,"sylvan-arms-sa5-pro-left-folder.plate_proud":0.03,"sylvan-arms-sa5-pro-left-folder.plate_top":0.06,"sylvan-arms-sa5-pro-left-folder.qd_behind_front":0.45,"sylvan-arms-sa5-pro-left-folder.qd_below_axis":1.2,"sylvan-arms-sa5-pro-left-folder.qd_bore_d":0.31,"sylvan-arms-sa5-pro-left-folder.qd_d":0.44,"sylvan-arms-sa5-pro-left-folder.qd_depth":0.3,"sylvan-arms-sa5-pro-left-folder.qd_proud":0.2,"sylvan-arms-sa5-pro-left-folder.rear_hex_below_axis":1.083,"sylvan-arms-sa5-pro-left-folder.rear_hex_d":0.26,"sylvan-arms-sa5-pro-left-folder.rear_hex_out":0.065,"sylvan-arms-sa5-pro-left-folder.rear_hole_below_axis":1.03,"sylvan-arms-sa5-pro-left-folder.rear_hole_d":0.21,"sylvan-arms-sa5-pro-left-folder.rear_hole_in":0.371,"sylvan-arms-sa5-pro-left-folder.rear_screw_below_axis":0.441,"sylvan-arms-sa5-pro-left-folder.rear_screw_d":0.19,"sylvan-arms-sa5-pro-left-folder.rear_screw_out":0.578,"sylvan-arms-sa5-pro-left-folder.receiver_bore_d":1.079,"sylvan-arms-sa5-pro-left-folder.receiver_half_length":0.568,"sylvan-arms-sa5-pro-left-folder.ring_r":0.737,"sylvan-arms-sa5-pro-left-folder.slot_below_axis":0.79,"sylvan-arms-sa5-pro-left-folder.slot_out":0.43,"sylvan-arms-sa5-pro-left-folder.small_hole_below_axis":0.718,"sylvan-arms-sa5-pro-left-folder.small_hole_d":0.124,"sylvan-arms-sa5-pro-left-folder.small_hole_left":0.098,"sylvan-arms-sa5-pro-left-folder.stock_block_length":0.5,"sylvan-arms-sa5-pro-left-folder.stock_half_length":0.686,"sylvan-arms-sa5-pro-left-folder.tab_below_axis":0.721,"sylvan-arms-sa5-pro-left-folder.tab_height":0.39,"sylvan-arms-sa5-pro-left-folder.tab_out":0.351,"sylvan-arms-sa5-pro-left-folder.tab_proud":0.17,"sylvan-arms-sa5-pro-left-folder.tab_width":0.16,"sylvan-arms-sa5-pro-left-folder.top_knuckle_bottom_below_axis":0.579},"profiles":{},"features":{},"placement":{},"bounds":{"min":[1.6615,-1.421,-1.4845],"max":[2.6,0.737,0.737]},"volume_in3":1.3601,"centroid":[2.1873,-0.6159,-0.268],"shell":[2.2126,-0.4853,-0.2277],"area_in2":14.8878,"triangles":20214,"manifold":true,"slabs":[[1.661,-1.421,-1.484,2.414,-0.217,-0.744],[1.914,-1.421,-0.744,2.6,0.635,-0.374],[1.914,-1.421,-0.374,2.6,0.737,-0.003],[1.744,-1.421,-0.003,2.6,0.737,0.367],[1.744,-1.421,0.367,2.6,0.639,0.737]],"slots":["body","hardware"]},"taurus-tx22-barrel-46":{"part":"taurus-tx22-barrel-46","model":"taurus-tx22-barrel-46.glb","script":"taurus_tx22_barrel_46.py","inputs":{"taurus-tx22-barrel-46.block_bottom":0.3,"taurus-tx22-barrel-46.block_front_x":1.467,"taurus-tx22-barrel-46.block_top":0.31,"taurus-tx22-barrel-46.block_width":0.58,"taurus-tx22-barrel-46.bore_d":0.218,"taurus-tx22-barrel-46.od":0.55,"taurus-tx22-barrel-46.shoulder_x":4.133,"taurus-tx22-barrel-46.stated_length":4.6,"taurus-tx22-barrel-46.thread_length":0.467,"taurus-tx22-barrel-46.thread_major_d":0.4957,"taurus-tx22-barrel-46.thread_minor_d":0.4551,"taurus-tx22-barrel-46.thread_pitch":0.03571},"profiles":{},"features":{},"placement":{},"bounds":{"min":[0,-0.3,-0.29],"max":[4.6,0.31,0.29]},"volume_in3":1.0639,"centroid":[1.9936,0.0025,0],"shell":[2.1887,0.0017,0.0001],"area_in2":12.9056,"triangles":6520,"manifold":true,"slabs":[[0,-0.3,-0.29,4.217,0.31,0.29],[4.217,-0.248,-0.248,4.6,0.248,0.248]],"slots":["barrel"]},"taurus-tx22-frame":{"part":"taurus-tx22-frame","model":"taurus-tx22-frame.glb","script":"taurus_tx22_frame.py","inputs":{"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_pitch":0.394,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835,"taurus-tx22-frame.body_width":0.93,"taurus-tx22-frame.bore_axis_y":0.467,"taurus-tx22-frame.controls_proud":0.05,"taurus-tx22-frame.cover_band_depth":0.04,"taurus-tx22-frame.dust_cover_bottom_y":-0.381,"taurus-tx22-frame.edge_round":0.06,"taurus-tx22-frame.finger_index_depth":0.03,"taurus-tx22-frame.front_pin_x":1.355,"taurus-tx22-frame.front_pin_y":0.03,"taurus-tx22-frame.grip_bottom_y":-4.024,"taurus-tx22-frame.grip_width":1.115,"taurus-tx22-frame.guard_bar_bottom_y":-1.771,"taurus-tx22-frame.guard_bar_top_y":-1.595,"taurus-tx22-frame.guard_width":0.4,"taurus-tx22-frame.magwell_across":0.64,"taurus-tx22-frame.magwell_x":-1.144,"taurus-tx22-frame.panel_recess":0.012,"taurus-tx22-frame.pin_end_d":0.065,"taurus-tx22-frame.rail_front_x":4.068,"taurus-tx22-frame.rail_length":1.75,"taurus-tx22-frame.rail_slot0_x":3.489,"taurus-tx22-frame.rail_slots":2,"taurus-tx22-frame.rail_top_y":-0.566,"taurus-tx22-frame.safety_proud":0.16,"taurus-tx22-frame.seam_y":0.165,"taurus-tx22-frame.slide_rear_x":-2.75,"taurus-tx22-frame.strap_round":0.3,"taurus-tx22-frame.trigger_drop":-0.07,"taurus-tx22-frame.trigger_pin_d":0.11,"taurus-tx22-frame.trigger_pin_x":0.499,"taurus-tx22-frame.trigger_pin_y":-0.77,"taurus-tx22-frame.trigger_width":0.3,"taurus-tx22-magazine-16.body_front_to_back":1.185,"taurus-tx22-magazine-16.pad_top_rise":1,"taurus-tx22-magazine-16.rake":12.119,"taurus-tx22-toro-slide.length":6.929,"taurus-tx22-toro-slide.lug_bottom":0.826,"taurus-tx22-toro-slide.lug_length":0.27,"taurus-tx22-toro-slide.lug_width":0.532},"profiles":{"side":[[-2.895,-3.45],[-2.888,-3.897],[-2.864,-4.041],[-2.839,-4.078],[-2.827,-4.081],[-2.82,-4.119],[-2.749,-4.185],[-2.661,-4.228],[-2.564,-4.252],[-2.531,-4.247],[-2.531,-4.219],[-2.459,-4.045],[-2.19,-4.046],[-2.14,-4.026],[-1.427,-4.023],[-1.255,-4.009],[-1.252,-3.99],[-1.215,-3.993],[-1.183,-4.011],[-1.127,-4.014],[-0.911,-3.962],[-0.855,-3.933],[-0.831,-3.908],[-0.804,-3.9],[-0.802,-3.825],[-0.821,-3.806],[-0.821,-3.778],[-0.843,-3.766],[-0.849,-3.725],[-0.856,-3.663],[-0.851,-3.572],[-0.83,-3.515],[-0.821,-3.453],[-0.808,-3.437],[-0.8,-3.368],[-0.787,-3.349],[-0.742,-3.155],[-0.712,-3.064],[-0.7,-2.989],[-0.691,-2.979],[-0.612,-2.684],[-0.6,-2.612],[-0.591,-2.603],[-0.579,-2.531],[-0.558,-2.474],[-0.558,-2.446],[-0.533,-2.38],[-0.534,-2.352],[-0.435,-2.226],[-0.419,-2.182],[-0.417,-2.113],[-0.437,-2.004],[-0.426,-1.863],[-0.398,-1.791],[-0.336,-1.69],[-0.296,-1.652],[-0.285,-1.625],[-0.236,-1.6],[-0.223,-1.578],[-0.195,-1.575],[-0.167,-1.555],[-0.133,-1.552],[-0.12,-1.539],[-0.039,-1.526],[0.074,-1.534],[0.23,-1.586],[0.422,-1.672],[0.551,-1.702],[2.015,-1.701],[2.117,-1.641],[2.15,-1.573],[2.146,-1.526],[2.127,-1.486],[2.097,-1.45],[2.07,-1.446],[2.067,-1.108],[2.084,-0.917],[2.102,-0.823],[2.169,-0.606],[2.182,-0.52],[3.368,-0.531],[3.385,-0.514],[3.388,-0.448],[3.411,-0.428],[3.558,-0.426],[3.585,-0.434],[3.598,-0.515],[3.618,-0.532],[3.769,-0.534],[3.782,-0.516],[3.788,-0.457],[3.808,-0.433],[3.965,-0.432],[3.976,-0.446],[3.976,-0.468],[3.998,-0.48],[4.002,-0.533],[4.009,-0.541],[4.044,-0.541],[4.061,-0.514],[4.079,-0.448],[4.112,-0.276],[4.131,-0.266],[4.134,-0.254],[4.127,-0.216],[4.142,-0.125],[4.134,0.025],[4.142,0.144],[4.081,0.157],[2.646,0.165],[-1.882,0.165],[-1.997,0.161],[-2.007,0.142],[-2.201,0.14],[-2.202,0.161],[-2.22,0.165],[-2.747,0.165],[-2.753,0.149],[-2.786,0.122],[-2.815,0.117],[-2.818,0.036],[-2.827,0.017],[-2.805,0.005],[-2.807,-0.092],[-2.824,-0.1],[-2.826,-0.08],[-2.837,-0.078],[-2.863,-0.124],[-2.853,-0.196],[-2.837,-0.218],[-2.769,-0.262],[-2.488,-0.291],[-2.387,-0.321],[-2.318,-0.327],[-2.309,-0.343],[-2.208,-0.37],[-2.142,-0.41],[-2.121,-0.407],[-2.116,-0.427],[-2.083,-0.441],[-2.081,-0.455],[-2.045,-0.49],[-2.024,-0.492],[-2.018,-0.523],[-1.996,-0.545],[-1.986,-0.604],[-1.973,-0.616],[-1.968,-0.779],[-1.981,-0.788],[-1.983,-0.864],[-2.005,-0.889],[-2.057,-1.064],[-2.124,-1.193],[-2.124,-1.209],[-2.226,-1.382],[-2.368,-1.58],[-2.547,-1.857],[-2.673,-2.099],[-2.731,-2.241],[-2.794,-2.47],[-2.854,-2.839],[-2.882,-3.115]],"left":[[-2.917,-3.754],[-2.899,-3.95],[-2.905,-4.02],[-2.893,-4.032],[-2.899,-4.096],[-2.88,-4.134],[-2.886,-4.146],[-2.88,-4.171],[-2.842,-4.241],[-2.776,-4.301],[-2.687,-4.339],[-2.637,-4.352],[-2.542,-4.346],[-2.479,-4.352],[-2.475,-4.064],[-2.466,-4.055],[-0.928,-3.956],[-0.9,-3.94],[-0.925,-3.921],[-0.887,-3.883],[-0.893,-3.782],[-0.887,-3.725],[-0.785,-3.352],[-0.753,-3.194],[-0.741,-3.175],[-0.696,-2.979],[-0.677,-2.934],[-0.658,-2.833],[-0.633,-2.764],[-0.62,-2.707],[-0.626,-2.7],[-0.614,-2.681],[-0.582,-2.561],[-0.582,-2.523],[-0.55,-2.441],[-0.474,-2.353],[-0.455,-2.308],[-0.449,-2.264],[-0.474,-2.144],[-0.467,-2.062],[-0.474,-2.049],[-0.461,-1.992],[-0.404,-1.853],[-0.322,-1.758],[-0.331,-1.742],[-0.353,-1.733],[-0.331,-1.711],[-0.312,-1.717],[-0.293,-1.698],[-0.249,-1.685],[-0.192,-1.648],[-0.185,-1.654],[-0.166,-1.635],[-0.154,-1.641],[-0.141,-1.629],[-0.122,-1.629],[-0.109,-1.61],[-0.084,-1.603],[-0.072,-1.616],[-0.053,-1.597],[-0.034,-1.61],[-0.037,-1.6],[-0.027,-1.591],[0.004,-1.597],[0.008,-1.581],[0.023,-1.578],[0.049,-1.597],[0.074,-1.591],[0.087,-1.61],[0.106,-1.604],[0.169,-1.629],[0.396,-1.743],[0.498,-1.775],[0.555,-1.781],[1.162,-1.776],[1.168,-1.769],[1.902,-1.777],[1.978,-1.77],[2.066,-1.72],[2.095,-1.685],[2.076,-1.622],[2.032,-1.571],[2.019,-1.54],[2.02,-1.147],[2.045,-0.951],[2.077,-0.819],[2.153,-0.578],[2.169,-0.556],[2.327,-0.556],[2.334,-0.563],[2.384,-0.556],[2.441,-0.569],[3.32,-0.564],[3.342,-0.548],[3.355,-0.472],[3.384,-0.45],[3.396,-0.463],[3.409,-0.456],[3.425,-0.472],[3.444,-0.535],[3.488,-0.555],[3.478,-0.564],[3.447,-0.558],[3.453,-0.57],[3.542,-0.577],[3.719,-0.564],[3.735,-0.548],[3.747,-0.479],[3.757,-0.469],[3.789,-0.469],[3.811,-0.498],[3.826,-0.577],[3.896,-0.59],[3.94,-0.577],[3.984,-0.577],[4.007,-0.542],[4.019,-0.492],[4.032,-0.372],[4.042,-0.362],[4.061,-0.369],[4.121,-0.302],[4.172,-0.005],[4.178,0.165],[-2.786,0.165],[-2.774,0.149],[-2.799,0.136],[-2.863,-0.199],[-2.856,-0.256],[-2.818,-0.319],[-2.771,-0.348],[-2.727,-0.36],[-2.569,-0.373],[-2.316,-0.431],[-2.196,-0.469],[-2.113,-0.507],[-2.034,-0.58],[-2.003,-0.636],[-1.978,-0.725],[-1.984,-0.731],[-1.978,-0.807],[-1.997,-0.927],[-1.984,-0.978],[-2.01,-0.991],[-2.022,-1.054],[-2.041,-1.086],[-2.06,-1.155],[-2.079,-1.18],[-2.073,-1.193],[-2.098,-1.225],[-2.098,-1.25],[-2.117,-1.269],[-2.137,-1.32],[-2.162,-1.351],[-2.156,-1.364],[-2.194,-1.408],[-2.295,-1.585],[-2.415,-1.749],[-2.415,-1.762],[-2.479,-1.844],[-2.536,-1.952],[-2.574,-2.002],[-2.682,-2.204],[-2.764,-2.419],[-2.796,-2.565],[-2.809,-2.584],[-2.815,-2.66],[-2.84,-2.755],[-2.834,-2.767],[-2.853,-2.843],[-2.86,-2.938],[-2.885,-3.083],[-2.879,-3.102],[-2.898,-3.216],[-2.898,-3.305],[-2.911,-3.4],[-2.911,-3.596],[-2.917,-3.602],[-2.911,-3.615],[-2.917,-3.634],[-2.905,-3.665],[-2.911,-3.703],[-2.892,-3.722],[-2.902,-3.732],[-2.911,-3.729]]},"features":{"side":{"guard_opening":[[[1.884,-1.444],[1.882,-1.175],[1.885,-1.172],[1.885,-1.147],[1.881,-1.144],[1.873,-0.95],[1.87,-0.947],[1.87,-0.919],[1.863,-0.894],[1.86,-0.841],[1.857,-0.838],[1.85,-0.784],[1.805,-0.61],[1.782,-0.588],[1.751,-0.579],[1.717,-0.579],[1.713,-0.576],[1.67,-0.573],[1.623,-0.564],[1.548,-0.559],[1.529,-0.553],[1.45,-0.55],[1.419,-0.544],[1.385,-0.545],[1.382,-0.542],[1.297,-0.536],[1.281,-0.524],[1.278,-0.514],[1.274,-0.455],[1.265,-0.455],[1.259,-0.465],[1.256,-0.515],[1.247,-0.524],[1.169,-0.519],[1.156,-0.512],[1.134,-0.513],[1.118,-0.507],[1.062,-0.504],[1.059,-0.501],[1.015,-0.498],[0.993,-0.492],[0.965,-0.492],[0.956,-0.486],[0.952,-0.474],[0.943,-0.474],[0.943,-0.48],[0.937,-0.486],[0.837,-0.487],[0.824,-0.481],[0.805,-0.481],[0.802,-0.478],[0.324,-0.483],[0.317,-0.505],[0.318,-0.52],[0.327,-0.533],[0.327,-0.558],[0.337,-0.561],[0.337,-0.576],[0.343,-0.582],[0.343,-0.595],[0.353,-0.614],[0.353,-0.657],[0.344,-0.695],[0.332,-0.714],[0.329,-0.727],[0.323,-0.73],[0.301,-0.764],[0.273,-0.79],[0.273,-0.799],[0.261,-0.815],[0.261,-0.821],[0.239,-0.846],[0.23,-0.849],[0.23,-0.856],[0.211,-0.875],[0.208,-0.884],[0.187,-0.909],[0.177,-0.925],[0.181,-0.941],[0.178,-0.972],[0.11,-1.057],[0.036,-1.167],[0.036,-1.183],[0.045,-1.189],[0.064,-1.195],[0.146,-1.241],[0.181,-1.257],[0.247,-1.297],[0.253,-1.297],[0.328,-1.34],[0.451,-1.401],[0.47,-1.407],[0.495,-1.423],[0.501,-1.423],[0.507,-1.429],[0.526,-1.435],[0.533,-1.441],[0.539,-1.441],[0.58,-1.463],[0.592,-1.462],[0.605,-1.469],[1.331,-1.462],[1.334,-1.465],[1.647,-1.462],[1.65,-1.465],[1.872,-1.466],[1.881,-1.46]]],"trigger":[[[0.339,-0.457],[0.327,-0.473],[0.317,-0.505],[0.318,-0.52],[0.327,-0.533],[0.327,-0.558],[0.337,-0.561],[0.337,-0.576],[0.343,-0.582],[0.343,-0.595],[0.353,-0.614],[0.35,-0.679],[0.329,-0.72],[0.329,-0.727],[0.323,-0.73],[0.301,-0.764],[0.273,-0.79],[0.273,-0.799],[0.261,-0.815],[0.261,-0.821],[0.242,-0.84],[0.246,-0.852],[0.394,-1.008],[0.533,-1.128],[0.716,-1.264],[0.782,-1.307],[0.829,-1.332],[0.838,-1.341],[0.845,-1.341],[0.851,-1.347],[0.885,-1.363],[0.929,-1.362],[0.948,-1.356],[1.051,-1.349],[1.082,-1.339],[1.095,-1.323],[1.095,-1.311],[1.104,-1.289],[1.1,-1.261],[1.059,-1.23],[0.993,-1.168],[0.917,-1.068],[0.882,-1.003],[0.876,-0.981],[0.86,-0.95],[0.86,-0.941],[0.844,-0.9],[0.831,-0.85],[0.827,-0.813],[0.821,-0.794],[0.82,-0.735],[0.817,-0.731],[0.819,-0.656],[0.826,-0.637],[0.825,-0.616],[0.832,-0.606],[0.84,-0.559],[0.868,-0.487],[0.837,-0.487],[0.824,-0.481],[0.78,-0.478],[0.749,-0.469],[0.671,-0.467],[0.658,-0.461],[0.627,-0.461],[0.605,-0.455],[0.477,-0.45],[0.473,-0.447],[0.408,-0.444],[0.405,-0.441],[0.37,-0.441]]],"safety_right":[[[-2.333,-0.144],[-2.326,-0.147],[-2.311,-0.147],[-2.308,-0.144],[-2.282,-0.147],[-2.27,-0.156],[-2.267,-0.165],[-2.239,-0.165],[-2.235,-0.171],[-2.207,-0.174],[-2.188,-0.183],[-2.129,-0.186],[-2.097,-0.192],[-2.041,-0.188],[-2.029,-0.185],[-2.026,-0.179],[-2.001,-0.179],[-1.998,-0.175],[-1.963,-0.172],[-1.948,-0.166],[-1.891,-0.159],[-1.882,-0.152],[-1.841,-0.146],[-1.835,-0.14],[-1.795,-0.136],[-1.785,-0.13],[-1.72,-0.12],[-1.71,-0.113],[-1.679,-0.11],[-1.67,-0.104],[-1.645,-0.103],[-1.617,-0.091],[-1.576,-0.087],[-1.526,-0.071],[-1.504,-0.071],[-1.479,-0.061],[-1.46,-0.061],[-1.426,-0.048],[-1.411,-0.048],[-1.364,-0.035],[-1.345,-0.035],[-1.301,-0.016],[-1.283,0.006],[-1.274,0.028],[-1.261,0.044],[-1.255,0.063],[-1.237,0.091],[-1.234,0.113],[-1.243,0.129],[-1.259,0.135],[-1.434,0.133],[-1.437,0.136],[-1.462,0.136],[-1.465,0.133],[-1.569,0.132],[-1.572,0.129],[-1.603,0.129],[-1.606,0.132],[-1.719,0.131],[-1.722,0.127],[-1.819,0.13],[-1.822,0.127],[-1.866,0.126],[-1.869,0.129],[-2.007,0.128],[-2.01,0.14],[-2.207,0.139],[-2.207,0.129],[-2.232,0.11],[-2.232,0.098],[-2.238,0.091],[-2.253,0.088],[-2.253,0.072],[-2.263,0.069],[-2.262,0.057],[-2.281,0.047],[-2.281,0.041],[-2.287,0.038],[-2.287,0.025],[-2.281,0.022],[-2.284,0],[-2.293,-0.009],[-2.303,-0.009],[-2.302,-0.019],[-2.318,-0.028],[-2.333,-0.053]]],"takedown_right":[[[1.27,-0.289],[1.163,-0.287],[1.16,-0.29],[0.951,-0.292],[0.938,-0.295],[0.932,-0.317],[0.933,-0.408],[0.936,-0.411],[0.936,-0.439],[0.943,-0.452],[0.943,-0.471],[0.952,-0.471],[0.959,-0.486],[0.965,-0.489],[0.993,-0.489],[0.996,-0.492],[1.04,-0.495],[1.062,-0.501],[1.118,-0.503],[1.134,-0.51],[1.156,-0.509],[1.169,-0.515],[1.253,-0.515],[1.253,-0.49],[1.259,-0.477],[1.259,-0.458],[1.265,-0.452],[1.274,-0.452],[1.276,-0.33],[1.273,-0.327]]],"magrelease_right":[[[-0.613,-0.992],[-0.629,-1.026],[-0.632,-1.051],[-0.644,-1.083],[-0.65,-1.12],[-0.662,-1.155],[-0.662,-1.202],[-0.655,-1.214],[-0.639,-1.23],[-0.614,-1.233],[-0.599,-1.239],[-0.58,-1.239],[-0.564,-1.245],[-0.545,-1.245],[-0.539,-1.251],[-0.517,-1.251],[-0.489,-1.26],[-0.455,-1.262],[-0.436,-1.269],[-0.373,-1.271],[-0.367,-1.277],[-0.335,-1.28],[-0.32,-1.286],[-0.273,-1.286],[-0.236,-1.254],[-0.229,-1.254],[-0.205,-1.216],[-0.192,-1.185],[-0.193,-1.169],[-0.18,-1.138],[-0.18,-1.125],[-0.174,-1.116],[-0.178,-1.069],[-0.2,-1.044],[-0.307,-1.017],[-0.335,-1.014],[-0.344,-1.008],[-0.41,-0.996],[-0.473,-0.978],[-0.485,-0.978],[-0.495,-0.972],[-0.507,-0.972],[-0.545,-0.96],[-0.582,-0.966],[-0.595,-0.973]]],"finger_index":[[[0.729,-0.06],[1.903,-0.049],[1.981,-0.079],[2.019,-0.135],[1.998,-0.261],[1.952,-0.355],[1.906,-0.393],[1.296,-0.399],[1.029,-0.301],[0.732,-0.304]]],"cover_band":[[[2.281,-0.336],[2.348,-0.198],[4.188,-0.181],[4.189,-0.341],[2.281,-0.358]]],"panels":[[[-1.997,-0.929],[-2.042,-1.077],[-2.11,-1.206],[-2.11,-1.221],[-2.264,-1.467],[-2.264,-1.479],[-2.279,-1.489],[-2.44,-1.722],[-2.48,-1.8],[-2.533,-1.87],[-2.548,-1.901],[-2.548,-1.936],[-2.573,-1.945],[-2.606,-2.005],[-2.72,-2.263],[-2.759,-2.391],[-2.795,-2.557],[-2.86,-3.027],[-2.879,-3.315],[-2.879,-3.662],[-2.854,-3.662],[-2.842,-3.634],[-2.798,-3.634],[-2.791,-3.649],[-2.751,-3.649],[-2.72,-3.639],[-2.689,-3.611],[-2.657,-3.61],[-2.629,-3.591],[-2.586,-3.585],[-2.58,-3.51],[-2.533,-3.506],[-2.529,-3.559],[-2.504,-3.562],[-2.504,-3.609],[-2.545,-3.612],[-2.544,-3.638],[-2.519,-3.672],[-2.443,-3.727],[-2.418,-3.727],[-2.415,-3.746],[-2.381,-3.767],[-2.352,-3.767],[-2.349,-3.792],[-2.317,-3.817],[-2.252,-3.819],[-2.168,-3.79],[-2.086,-3.78],[-1.612,-3.654],[-1.39,-3.583],[-1.331,-3.579],[-1.327,-3.633],[-1.339,-3.692],[-1.302,-3.723],[-1.242,-3.751],[-1.164,-3.762],[-1.104,-3.809],[-1.047,-3.811],[-1.003,-3.83],[-0.978,-3.83],[-0.944,-3.807],[-0.882,-3.804],[-0.872,-3.797],[-0.873,-3.769],[-0.86,-3.75],[-0.87,-3.688],[-0.856,-3.509],[-0.844,-3.503],[-0.835,-3.44],[-0.823,-3.421],[-0.823,-3.381],[-0.804,-3.346],[-0.726,-3.051],[-0.714,-2.951],[-0.702,-2.948],[-0.693,-2.923],[-0.687,-2.857],[-0.675,-2.848],[-0.548,-2.343],[-0.511,-2.283],[-0.449,-2.213],[-0.434,-2.17],[-0.451,-1.951],[-0.449,-1.891],[-0.427,-1.835],[-0.428,-1.794],[-0.415,-1.791],[-0.351,-1.678],[-0.31,-1.64],[-0.31,-1.615],[-0.326,-1.615],[-0.332,-1.627],[-0.436,-1.628],[-0.439,-1.606],[-0.461,-1.597],[-0.533,-1.589],[-0.551,-1.604],[-0.554,-1.648],[-0.607,-1.649],[-0.626,-1.665],[-0.635,-1.749],[-0.672,-1.803],[-0.686,-1.893],[-0.736,-1.9],[-0.74,-1.841],[-0.716,-1.772],[-0.713,-1.715],[-0.704,-1.712],[-0.698,-1.646],[-0.72,-1.618],[-0.724,-1.568],[-0.824,-1.529],[-0.856,-1.488],[-0.919,-1.464],[-0.972,-1.464],[-0.985,-1.436],[-1.029,-1.434],[-1.076,-1.39],[-1.176,-1.35],[-1.422,-1.224],[-1.45,-1.218],[-1.51,-1.178],[-1.679,-1.105],[-1.692,-1.086],[-1.739,-1.087],[-1.751,-1.102],[-1.754,-1.14],[-1.788,-1.14],[-1.795,-1.156],[-1.838,-1.156],[-1.858,-1.1],[-1.877,-1.085],[-1.909,-0.972],[-1.934,-0.944],[-1.978,-0.945],[-1.984,-0.929]]],"panel_band_back":[[[-1.985,-0.879],[-1.886,-1.075],[-1.795,-1.416],[-2.182,-1.907],[-2.209,-1.976],[-2.508,-3.562],[-2.391,-3.602],[-2.112,-1.994],[-2.094,-1.975],[-1.708,-1.415],[-1.776,-1.162]]],"panel_band_front":[[[-0.737,-1.544],[-0.727,-1.593],[-0.771,-2.257],[-1.141,-3.549],[-1.218,-3.622],[-1.099,-3.621],[-1.062,-3.589],[-0.74,-2.179],[-0.648,-1.69],[-0.57,-1.623]]]},"left":{"slide_stop":[[[-0.395,0.057],[-0.767,0.067],[-0.815,-0.026],[-0.858,-0.121],[-0.847,-0.138],[-0.471,-0.139],[-0.411,-0.05]]]}},"placement":{"side":{"plane":"xy","offset":{}},"left":{"plane":"xy","offset":{}}},"bounds":{"min":[-2.895,-4.252,-0.625],"max":[4.142,0.165,0.625]},"volume_in3":9.55,"centroid":[-0.4689,-1.4021,-0.0001],"shell":[-0.435,-1.4224,-0.0055],"area_in2":71.3922,"triangles":16204,"manifold":true,"slabs":[[-2.895,-4.252,-0.558,-2.504,0.154,0.558],[-2.504,-4.155,-0.625,-2.113,0.165,0.625],[-2.113,-4.041,-0.625,-0.94,0.165,0.625],[-0.94,-3.969,-0.608,-0.549,0.165,0.608],[-0.549,-2.423,-0.608,-0.158,0.165,0.608],[-0.158,-1.589,-0.558,0.233,0.165,0.558],[0.233,-1.77,-0.547,1.405,0.165,0.547],[1.405,-1.77,-0.487,2.187,0.165,0.487],[2.187,-0.566,-0.47,4.142,0.165,0.47]],"slots":["body","panels","controls","trigger","pins","trigger_pin"]},"taurus-tx22-magazine-16":{"part":"taurus-tx22-magazine-16","model":"taurus-tx22-magazine-16.glb","script":"taurus_tx22_magazine_16.py","inputs":{"taurus-tx22-magazine-16.base_pad_length":1.63,"taurus-tx22-magazine-16.body_across":1.159,"taurus-tx22-magazine-16.body_front_to_back":1.185,"taurus-tx22-magazine-16.body_width":0.64,"taurus-tx22-magazine-16.button_proud":0.06,"taurus-tx22-magazine-16.catch_notch_depth":0.06,"taurus-tx22-magazine-16.dimple_depth":0.015,"taurus-tx22-magazine-16.follower_depth":0.45,"taurus-tx22-magazine-16.groove_depth":0.03,"taurus-tx22-magazine-16.inside_length":1.03,"taurus-tx22-magazine-16.inside_width":0.4,"taurus-tx22-magazine-16.pad_front_ahead":0.384,"taurus-tx22-magazine-16.pad_top_rise":1,"taurus-tx22-magazine-16.plug_ring_depth":0.02,"taurus-tx22-magazine-16.rake":12.119},"profiles":{"body":[[-1.22,0.006],[-1.207,0],[0,0.037],[-0.016,0.068],[0.014,0.215],[0.156,0.844],[0.486,2.414],[0.591,2.868],[0.633,3.098],[0.893,4.246],[0.865,4.26],[0.825,4.257],[0.795,4.303],[0.77,4.32],[0.573,4.355],[0.511,4.413],[0.464,4.434],[0.425,4.422],[0.363,4.353],[0.25,4.331],[0.239,4.347],[0.239,4.399],[0.223,4.416],[0.201,4.421],[-0.234,4.403],[-0.268,4.39],[-0.285,4.359],[-0.821,1.823]],"end":[[0,-6.087],[0.012,-6.104],[0.012,-6.116],[0,-6.139],[0.026,-6.154],[0.102,-6.148],[0.12,-6.165],[0.172,-6.165],[0.184,-6.154],[0.26,-6.154],[0.272,-6.165],[0.324,-6.165],[0.336,-6.171],[0.342,-6.165],[0.406,-6.165],[0.418,-6.154],[0.441,-6.154],[0.453,-6.165],[0.488,-6.16],[0.5,-6.171],[0.529,-6.171],[0.535,-6.177],[0.546,-6.171],[0.581,-6.183],[0.593,-6.177],[0.698,-6.177],[0.704,-6.171],[0.716,-6.177],[0.728,-6.171],[0.733,-6.177],[0.763,-6.177],[0.768,-6.183],[0.815,-6.183],[0.821,-6.177],[0.891,-6.177],[0.909,-6.171],[0.92,-6.16],[0.961,-6.177],[1.043,-6.177],[1.067,-6.16],[1.119,-6.16],[1.154,-6.13],[1.178,-6.142],[1.204,-6.127],[1.221,-6.098],[1.216,-6.092],[1.227,-6.081],[1.233,-6.04],[1.245,-6.016],[1.239,-5.999],[1.245,-5.993],[1.245,-5.964],[1.251,-5.958],[1.251,-5.736],[1.245,-5.73],[1.245,-5.648],[1.233,-5.631],[1.233,-5.134],[1.227,-5.128],[1.227,-5.099],[1.233,-5.093],[1.233,-5.011],[1.239,-5.005],[1.239,-4.859],[1.233,-4.853],[1.233,-4.801],[1.227,-4.795],[1.221,-4.737],[1.186,-4.643],[1.186,-4.544],[1.192,-4.538],[1.186,-4.532],[1.186,-4.287],[1.166,-4.266],[1.143,-4.254],[1.02,-4.214],[0.999,-4.187],[0.999,-3.609],[0.993,-3.603],[0.993,-3.486],[0.999,-3.474],[0.993,-3.468],[0.993,-0.342],[0.929,-0.167],[0.915,-0.164],[0.903,-0.169],[0.888,-0.155],[0.792,0],[0.763,0],[0.739,-0.023],[0.704,-0.023],[0.657,-0.064],[0.637,-0.073],[0.637,-0.091],[0.617,-0.117],[0.558,-0.117],[0.552,-0.123],[0.538,-0.108],[0.555,-0.079],[0.555,-0.067],[0.543,-0.056],[0.543,-0.003],[0.529,0],[0.5,-0.012],[0.476,-0.035],[0.459,-0.041],[0.418,-0.076],[0.397,-0.085],[0.374,-0.131],[0.345,-0.219],[0.327,-0.248],[0.316,-0.295],[0.298,-0.324],[0.292,-0.354],[0.281,-0.371],[0.281,-0.383],[0.269,-0.4],[0.24,-0.482],[0.24,-0.856],[0.245,-0.862],[0.245,-2.031],[0.251,-2.037],[0.257,-4.269],[0.245,-4.281],[0.24,-4.304],[0.169,-4.374],[0.146,-4.409],[0.117,-4.479],[0.094,-4.55],[0.094,-4.567],[0.067,-4.593],[0.056,-4.593],[0.035,-4.614],[0.023,-4.672],[0.018,-4.678],[0.018,-4.702],[0.012,-4.707],[0.012,-5.73],[0.006,-5.742],[0.012,-5.748],[0.012,-5.765],[0.006,-5.771],[0.006,-5.859],[0.018,-5.87],[0.006,-5.882],[0.006,-6.075]],"pad":[[-5.951,-3.661],[-5.942,-3.658],[-5.913,-3.598],[-5.905,-3.608],[-5.92,-3.664],[-5.897,-3.672],[-5.264,-3.704],[-4.885,-3.713],[-4.586,-3.704],[-4.41,-3.672],[-4.321,-3.644],[-4.266,-3.616],[-4.218,-3.577],[-4.188,-3.527],[-4.189,-3.519],[-4.208,-3.535],[-4.215,-3.527],[-4.212,-3.512],[-4.194,-3.496],[-4.199,-3.486],[-4.208,-3.492],[-4.216,-3.484],[-4.204,-3.466],[-4.231,-3.444],[-4.238,-3.429],[-4.229,-3.416],[-4.239,-3.424],[-4.247,-3.417],[-4.241,-3.41],[-4.253,-3.398],[-4.25,-3.389],[-4.275,-3.383],[-4.254,-3.352],[-4.26,-3.343],[-4.246,-3.319],[-4.277,-3.347],[-4.348,-3.382],[-4.548,-3.43],[-4.579,-3.43],[-4.603,-3.415],[-4.687,-3.415],[-4.693,-3.428],[-4.791,-3.429],[-4.844,-3.438],[-4.856,-3.432],[-5.171,-3.447],[-5.519,-3.443],[-5.525,-3.428],[-5.541,-3.428],[-5.584,-3.435],[-5.608,-3.46],[-5.868,-3.455],[-5.887,-3.488]],"plan":[[-1.63,-0.369],[-1.622,-0.504],[-1.617,-0.524],[-1.6,-0.539],[-1.209,-0.581],[-0.759,-0.593],[-0.45,-0.578],[-0.3,-0.517],[-0.217,-0.461],[-0.136,-0.384],[-0.056,-0.256],[-0.016,-0.135],[0,0],[0,0.02],[-0.028,0.186],[-0.079,0.303],[-0.16,0.41],[-0.26,0.492],[-0.347,0.538],[-0.445,0.572],[-0.688,0.589],[-0.944,0.593],[-1.341,0.575],[-1.557,0.556],[-1.593,0.544],[-1.609,0.487],[-1.616,0.399]]},"features":{"body":{"slot":[[[-0.904,0.269],[-0.882,0.321],[-0.848,0.348],[-0.831,0.379],[-0.143,3.593],[-0.103,3.61],[0.055,3.578],[0.066,3.561],[-0.045,3.028],[-0.634,0.315],[-0.608,0.248],[-0.614,0.192],[-0.654,0.138],[-0.683,0.119],[-0.72,0.104],[-0.761,0.101],[-0.83,0.121],[-0.86,0.144],[-0.896,0.199]]],"button_hole":[[[-0.074,3.902],[-0.065,3.945],[-0.041,3.98],[0.003,4.013],[0.034,4.024],[0.083,4.014],[0.108,3.998],[0.132,3.967],[0.144,3.913],[0.116,3.778],[0.093,3.762],[0.058,3.758],[0.02,3.766],[-0.04,3.807],[-0.068,3.85]]],"small_slot":[[[-0.31,3.803],[-0.25,4.063],[-0.218,4.093],[-0.208,4.077],[-0.22,3.989],[-0.263,3.782],[-0.279,3.771],[-0.29,3.774]]],"catch_notch":[[[0.44,3.002],[0.598,2.969],[0.577,2.866],[0.419,2.898]]],"groove":[[[0.329,4.193],[0.422,4.174],[-0.408,0.161],[-0.501,0.18]]]},"end":{},"pad":{},"plan":{"plug":[[[-0.782,0.098],[-0.57,0.098],[-0.57,-0.112],[-0.782,-0.112]]],"plug_face":[[[-0.765,0.081],[-0.587,0.081],[-0.587,-0.095],[-0.765,-0.095]]],"dimple":[[[-0.269,0.038],[-0.204,0.038],[-0.204,-0.033],[-0.269,-0.033]]]}},"placement":{"body":{"plane":"xy","offset":{}},"end":{"plane":"zy","offset":{}},"pad":{"plane":"xy","offset":{}},"plan":{"plane":"xz","offset":{}}},"bounds":{"min":[-1.246,-0.2874,-0.593],"max":[0.893,4.3952,0.593]},"volume_in3":1.9945,"centroid":[-0.2458,1.5567,0.0001],"shell":[-0.1864,1.8258,0.0007],"area_in2":35.5444,"triangles":1798,"manifold":true,"slabs":[[-1.246,-0.287,-0.593,0.384,0.103,0.593],[-1.191,0.103,-0.32,0.328,0.493,0.32],[-1.105,0.493,-0.32,0.172,0.883,0.32],[-1.019,0.883,-0.32,0.254,1.273,0.32],[-0.934,1.273,-0.32,0.336,1.664,0.32],[-0.848,1.664,-0.32,0.418,2.054,0.32],[-0.764,2.054,-0.32,0.502,2.444,0.32],[-0.682,2.444,-0.32,0.592,2.834,0.32],[-0.599,2.834,-0.32,0.67,3.225,0.32],[-0.517,3.225,-0.32,0.758,3.615,0.32],[-0.434,3.615,-0.38,0.847,4.005,0.38],[-0.352,4.005,-0.32,0.893,4.395,0.32]],"slots":["body","pad"]},"taurus-tx22-magazine-22":{"part":"taurus-tx22-magazine-22","model":"taurus-tx22-magazine-22.glb","script":"taurus_tx22_magazine_22.py","inputs":{"taurus-tx22-magazine-16.body_across":1.159,"taurus-tx22-magazine-16.body_front_to_back":1.185,"taurus-tx22-magazine-16.pad_top_rise":1,"taurus-tx22-magazine-16.rake":12.119,"taurus-tx22-magazine-22.body_width":0.64,"taurus-tx22-magazine-22.catch_notch_depth":0.06,"taurus-tx22-magazine-22.follower_depth":0.45,"taurus-tx22-magazine-22.groove_depth":0.03,"taurus-tx22-magazine-22.inside_length":1.03,"taurus-tx22-magazine-22.inside_width":0.4,"taurus-tx22-magazine-22.panel_depth":0.015,"taurus-tx22-magazine-22.sleeve_wall":0.08,"taurus-tx22-magazine-22.sleeve_width":1.115,"taurus-tx22-magazine-22.step_depth":0.02},"profiles":{"side":[[-1.544,0.314],[-1.526,0.274],[-1.386,0.239],[-0.36,0.021],[-0.149,0],[-0.096,0.006],[-0.04,0.043],[0,0.239],[-0.008,0.257],[0.052,0.545],[0.332,1.706],[0.303,1.744],[0.221,1.761],[0.074,1.763],[0.063,1.765],[0.049,1.793],[0.551,4.139],[0.657,4.593],[0.699,4.823],[0.959,5.971],[0.931,5.985],[0.89,5.982],[0.86,6.028],[0.835,6.045],[0.638,6.08],[0.577,6.138],[0.53,6.159],[0.491,6.147],[0.428,6.078],[0.316,6.056],[0.305,6.072],[0.304,6.123],[0.288,6.141],[0.266,6.145],[-0.168,6.128],[-0.202,6.115],[-0.22,6.084],[-1.099,1.968],[-1.155,1.725],[-1.188,1.703],[-1.203,1.661],[-1.229,1.644],[-1.29,1.458],[-1.45,0.714],[-1.521,0.451],[-1.516,0.422]],"end":[[0,-6.087],[0.012,-6.104],[0.012,-6.116],[0,-6.139],[0.026,-6.154],[0.102,-6.148],[0.12,-6.165],[0.172,-6.165],[0.184,-6.154],[0.26,-6.154],[0.272,-6.165],[0.324,-6.165],[0.336,-6.171],[0.342,-6.165],[0.406,-6.165],[0.418,-6.154],[0.441,-6.154],[0.453,-6.165],[0.488,-6.16],[0.5,-6.171],[0.529,-6.171],[0.535,-6.177],[0.546,-6.171],[0.581,-6.183],[0.593,-6.177],[0.698,-6.177],[0.704,-6.171],[0.716,-6.177],[0.728,-6.171],[0.733,-6.177],[0.763,-6.177],[0.768,-6.183],[0.815,-6.183],[0.821,-6.177],[0.891,-6.177],[0.909,-6.171],[0.92,-6.16],[0.961,-6.177],[1.043,-6.177],[1.067,-6.16],[1.119,-6.16],[1.154,-6.13],[1.178,-6.142],[1.204,-6.127],[1.221,-6.098],[1.216,-6.092],[1.227,-6.081],[1.233,-6.04],[1.245,-6.016],[1.239,-5.999],[1.245,-5.993],[1.245,-5.964],[1.251,-5.958],[1.251,-5.736],[1.245,-5.73],[1.245,-5.648],[1.233,-5.631],[1.233,-5.134],[1.227,-5.128],[1.227,-5.099],[1.233,-5.093],[1.233,-5.011],[1.239,-5.005],[1.239,-4.859],[1.233,-4.853],[1.233,-4.801],[1.227,-4.795],[1.221,-4.737],[1.186,-4.643],[1.186,-4.544],[1.192,-4.538],[1.186,-4.532],[1.186,-4.287],[1.166,-4.266],[1.143,-4.254],[1.02,-4.214],[0.999,-4.187],[0.999,-3.609],[0.993,-3.603],[0.993,-3.486],[0.999,-3.474],[0.993,-3.468],[0.993,-0.342],[0.929,-0.167],[0.915,-0.164],[0.903,-0.169],[0.888,-0.155],[0.792,0],[0.763,0],[0.739,-0.023],[0.704,-0.023],[0.657,-0.064],[0.637,-0.073],[0.637,-0.091],[0.617,-0.117],[0.558,-0.117],[0.552,-0.123],[0.538,-0.108],[0.555,-0.079],[0.555,-0.067],[0.543,-0.056],[0.543,-0.003],[0.529,0],[0.5,-0.012],[0.476,-0.035],[0.459,-0.041],[0.418,-0.076],[0.397,-0.085],[0.374,-0.131],[0.345,-0.219],[0.327,-0.248],[0.316,-0.295],[0.298,-0.324],[0.292,-0.354],[0.281,-0.371],[0.281,-0.383],[0.269,-0.4],[0.24,-0.482],[0.24,-0.856],[0.245,-0.862],[0.245,-2.031],[0.251,-2.037],[0.257,-4.269],[0.245,-4.281],[0.24,-4.304],[0.169,-4.374],[0.146,-4.409],[0.117,-4.479],[0.094,-4.55],[0.094,-4.567],[0.067,-4.593],[0.056,-4.593],[0.035,-4.614],[0.023,-4.672],[0.018,-4.678],[0.018,-4.702],[0.012,-4.707],[0.012,-5.73],[0.006,-5.742],[0.012,-5.748],[0.012,-5.765],[0.006,-5.771],[0.006,-5.859],[0.018,-5.87],[0.006,-5.882],[0.006,-6.075]]},"features":{"side":{"slot":[[[-0.839,1.994],[-0.817,2.046],[-0.783,2.073],[-0.765,2.103],[-0.078,5.318],[-0.037,5.335],[0.12,5.302],[0.131,5.286],[0.021,4.753],[-0.569,2.04],[-0.543,1.972],[-0.549,1.917],[-0.588,1.863],[-0.618,1.843],[-0.655,1.828],[-0.695,1.825],[-0.765,1.845],[-0.794,1.868],[-0.831,1.924]]],"button_hole":[[[-0.008,5.627],[0.001,5.67],[0.025,5.705],[0.069,5.738],[0.099,5.749],[0.148,5.739],[0.173,5.722],[0.198,5.692],[0.21,5.638],[0.181,5.502],[0.158,5.487],[0.124,5.483],[0.086,5.491],[0.026,5.532],[-0.002,5.574]]],"small_slot":[[[-0.244,5.528],[-0.185,5.788],[-0.153,5.818],[-0.142,5.802],[-0.155,5.714],[-0.197,5.507],[-0.214,5.496],[-0.225,5.499]]],"catch_notch":[[[0.506,4.727],[0.663,4.694],[0.642,4.591],[0.484,4.623]]],"groove":[[[0.395,5.918],[0.487,5.898],[-0.343,1.886],[-0.435,1.905]]],"panel":[[[-1.163,0.825],[-0.064,1.148],[-0.22,0.341],[-0.722,0.433]]],"step":[[[-1.135,0.904],[-0.007,1.261],[-0.221,0.228],[-1.232,0.437]]],"base":[[[-1.516,0.518],[0.034,0.198],[-0.023,-0.08],[-1.573,0.241]]]},"end":{}},"placement":{"side":{"plane":"xy","offset":{}},"end":{"plane":"zy","offset":{}}},"bounds":{"min":[-1.5937,-1.765,-0.5575],"max":[0.9093,4.3922,0.5575]},"volume_in3":2.6125,"centroid":[-0.361,0.7716,0],"shell":[-0.387,0.745,0],"area_in2":55.2401,"triangles":1220,"manifold":true,"slabs":[[-1.594,-1.765,-0.558,-0.031,-1.38,0.558],[-1.575,-1.38,-0.553,0.056,-0.995,0.553],[-1.488,-0.995,-0.545,0.149,-0.611,0.545],[-1.405,-0.611,-0.545,0.242,-0.226,0.545],[-1.313,-0.226,-0.545,0.282,0.159,0.545],[-1.159,0.159,-0.32,0.11,0.544,0.32],[-1.076,0.544,-0.32,0.192,0.929,0.32],[-0.994,0.929,-0.32,0.274,1.314,0.32],[-0.912,1.314,-0.32,0.357,1.698,0.32],[-0.829,1.698,-0.32,0.439,2.083,0.32],[-0.747,2.083,-0.32,0.523,2.468,0.32],[-0.665,2.468,-0.32,0.612,2.853,0.32],[-0.583,2.853,-0.32,0.69,3.238,0.32],[-0.501,3.238,-0.32,0.777,3.623,0.32],[-0.418,3.623,-0.32,0.864,4.007,0.32],[-0.336,4.007,-0.32,0.909,4.392,0.32]],"slots":["body","sleeve","base"]},"taurus-tx22-thread-protector":{"part":"taurus-tx22-thread-protector","model":"taurus-tx22-thread-protector.glb","script":"taurus_tx22_thread_protector.py","inputs":{"taurus-tx22-barrel-46.thread_length":0.467,"taurus-tx22-barrel-46.thread_major_d":0.4957,"taurus-tx22-barrel-46.thread_minor_d":0.4551,"taurus-tx22-barrel-46.thread_pitch":0.03571,"taurus-tx22-thread-protector.across_flats":0.565,"taurus-tx22-thread-protector.flats_length":0.357,"taurus-tx22-thread-protector.front_round":0.07,"taurus-tx22-thread-protector.front_wall":0.06,"taurus-tx22-thread-protector.hole_d":0.25,"taurus-tx22-thread-protector.length":0.527,"taurus-tx22-thread-protector.od":0.59},"profiles":{},"features":{},"placement":{},"bounds":{"min":[0,-0.295,-0.295],"max":[0.527,0.295,0.295]},"volume_in3":0.0506,"centroid":[0.297,-0.0002,-0.0001],"shell":[0.2739,0.0008,0.0005],"area_in2":2.4641,"triangles":7768,"manifold":true,"slabs":[[0,-0.295,-0.295,0.527,0.295,0.295]],"slots":["body"]},"taurus-tx22-toro-slide.body":{"part":"taurus-tx22-toro-slide","component":"body","model":"taurus-tx22-toro-slide.body.glb","script":"taurus_tx22_toro_slide.py","inputs":{"taurus-tx22-barrel-46.block_top":0.31,"taurus-tx22-barrel-46.block_width":0.58,"taurus-tx22-barrel-46.od":0.55,"taurus-tx22-toro-slide.bore_clearance":0.012,"taurus-tx22-toro-slide.bottom_below_axis":0.302,"taurus-tx22-toro-slide.breech_x":2.796,"taurus-tx22-toro-slide.cut_floor":0.44,"taurus-tx22-toro-slide.cut_front_x":2.504,"taurus-tx22-toro-slide.cut_rear_x":0.841,"taurus-tx22-toro-slide.floor_edge_break":0.005,"taurus-tx22-toro-slide.front_corner":0.045,"taurus-tx22-toro-slide.front_dot_d":0.07,"taurus-tx22-toro-slide.front_sight_width":0.14,"taurus-tx22-toro-slide.guide_rod_d":0.3,"taurus-tx22-toro-slide.guide_rod_y":0.56,"taurus-tx22-toro-slide.height":0.514,"taurus-tx22-toro-slide.length":6.929,"taurus-tx22-toro-slide.lug_bottom":0.826,"taurus-tx22-toro-slide.lug_length":0.27,"taurus-tx22-toro-slide.lug_width":0.532,"taurus-tx22-toro-slide.nose_bevel_across":23,"taurus-tx22-toro-slide.nose_bevel_front_y":0.151,"taurus-tx22-toro-slide.nose_bevel_rear_y":0.274,"taurus-tx22-toro-slide.nose_rear_x":4.263,"taurus-tx22-toro-slide.port_floor":0.09,"taurus-tx22-toro-slide.rear_block_front_x":3.02,"taurus-tx22-toro-slide.rear_end":0.12,"taurus-tx22-toro-slide.rear_notch_depth":0.07,"taurus-tx22-toro-slide.rear_notch_width":0.12,"taurus-tx22-toro-slide.rear_sight_width":0.6,"taurus-tx22-toro-slide.right_window_front_x":5.39,"taurus-tx22-toro-slide.right_window_rear_x":4.46,"taurus-tx22-toro-slide.screw_hole_d":0.1,"taurus-tx22-toro-slide.screw_spacing":0.42,"taurus-tx22-toro-slide.screw_x":1.278,"taurus-tx22-toro-slide.serration_count_front":5,"taurus-tx22-toro-slide.serration_count_rear":7,"taurus-tx22-toro-slide.serration_depth":0.035,"taurus-tx22-toro-slide.top_chamfer":0.07,"taurus-tx22-toro-slide.top_window_front_x":6.21,"taurus-tx22-toro-slide.top_window_rear_x":4.5,"taurus-tx22-toro-slide.top_window_width":0.38,"taurus-tx22-toro-slide.underside_depth":0.22,"taurus-tx22-toro-slide.wall":0.09,"taurus-tx22-toro-slide.width":0.93,"taurus-tx22-toro-slide.window_depth":0.3},"profiles":{"side":[[-0.049,-0.293],[6.925,-0.304],[6.929,0.426],[6.917,0.471],[6.876,0.512],[6.692,0.518],[4.364,0.515],[4.279,0.417],[4.26,0.379],[4.26,0.29],[4.184,0.17],[4.104,0.079],[4.016,0.022],[3.94,0.003],[3.13,0.004],[3.051,0.058],[3.013,0.127],[2.988,0.254],[2.988,0.374],[3.007,0.387],[3.02,0.444],[2.954,0.523],[2.536,0.523],[2.517,0.441],[0.834,0.443],[0.822,0.525],[0.126,0.532],[0.098,0.517],[0.072,0.403]]},"features":{"side":{"front_sight":[[[6.692,0.515],[6.661,0.578],[6.623,0.604],[6.401,0.629],[6.351,0.604],[6.338,0.515]]],"rear_sight":[[[0.544,0.51],[0.493,0.693],[0.367,0.693],[0.303,0.51]]],"cover_plate":[[[2.504,0.438],[2.504,0.526],[2.479,0.539],[2.34,0.539],[2.1,0.521],[2.081,0.54],[1.992,0.537],[1.72,0.527],[1.701,0.54],[1.379,0.54],[1.322,0.553],[1.265,0.553],[1.17,0.541],[0.961,0.528],[0.942,0.544],[0.898,0.547],[0.847,0.522],[0.841,0.44]]],"cover_screws":[[[1.341,0.566],[1.214,0.566],[1.214,0.541],[1.341,0.54]],[[0.955,0.56],[0.879,0.56],[0.879,0.535],[0.955,0.535]]],"left_window":[[[5.439,0.232],[4.269,0.233],[4.218,0.202],[4.193,0.113],[4.205,0.018],[4.25,-0.039],[5.249,-0.04],[5.3,0.011]]],"front_lug":[[[6.919,-0.308],[6.843,-0.307],[6.842,-0.826],[6.918,-0.826]]],"front_serrations":[[[6.56,0.186],[6.434,0.186],[6.228,-0.155],[6.355,-0.155]],[[6.358,0.187],[6.231,0.187],[6.026,-0.155],[6.152,-0.155]],[[6.155,0.187],[6.029,0.187],[5.823,-0.154],[5.95,-0.155]],[[5.953,0.187],[5.826,0.187],[5.621,-0.154],[5.747,-0.154]],[[5.75,0.187],[5.624,0.187],[5.419,-0.154],[5.545,-0.154]]],"rear_serrations":[[[1.949,0.375],[1.81,0.375],[1.465,-0.238],[1.604,-0.238]],[[1.74,0.376],[1.601,0.376],[1.256,-0.237],[1.395,-0.238]],[[1.531,0.376],[1.392,0.376],[1.047,-0.237],[1.187,-0.237]],[[1.326,0.376],[1.187,0.376],[0.842,-0.237],[0.981,-0.237]],[[1.114,0.376],[0.975,0.376],[0.63,-0.237],[0.769,-0.237]],[[0.905,0.377],[0.766,0.377],[0.421,-0.236],[0.56,-0.237]],[[0.696,0.377],[0.557,0.377],[0.212,-0.236],[0.352,-0.236]]]}},"placement":{"side":{"plane":"xy","offset":{}}},"bounds":{"min":[-0.049,-0.826,-0.465],"max":[6.929,0.693,0.465]},"volume_in3":2.6762,"centroid":[3.1299,0.1232,-0.0001],"shell":[3.6417,0.051,-0.0027],"area_in2":32.0462,"triangles":2340,"manifold":true,"slabs":[[-0.049,-0.302,-0.465,0.339,0.61,0.465],[0.339,-0.302,-0.465,0.726,0.693,0.465],[0.726,-0.302,-0.465,1.114,0.526,0.465],[1.114,-0.302,-0.465,2.277,0.443,0.465],[2.277,-0.302,-0.465,3.052,0.523,0.465],[3.052,-0.302,-0.465,3.44,0.057,0.465],[3.44,-0.302,-0.465,3.828,0.004,0.465],[3.828,-0.302,-0.465,4.215,0.219,0.465],[4.215,-0.302,-0.465,6.154,0.517,0.465],[6.154,-0.302,-0.465,6.541,0.629,0.465],[6.541,-0.826,-0.465,6.929,0.613,0.465]],"slots":["body","front_sight","front_dot","rear_sight","guide_rod"]},"taurus-tx22-toro-slide.cover":{"part":"taurus-tx22-toro-slide","component":"cover","model":"taurus-tx22-toro-slide.cover.glb","script":"taurus_tx22_toro_slide.py","inputs":{"taurus-tx22-barrel-46.block_top":0.31,"taurus-tx22-barrel-46.block_width":0.58,"taurus-tx22-barrel-46.od":0.55,"taurus-tx22-toro-slide.bore_clearance":0.012,"taurus-tx22-toro-slide.bottom_below_axis":0.302,"taurus-tx22-toro-slide.breech_x":2.796,"taurus-tx22-toro-slide.cut_floor":0.44,"taurus-tx22-toro-slide.cut_front_x":2.504,"taurus-tx22-toro-slide.cut_rear_x":0.841,"taurus-tx22-toro-slide.floor_edge_break":0.005,"taurus-tx22-toro-slide.front_corner":0.045,"taurus-tx22-toro-slide.front_dot_d":0.07,"taurus-tx22-toro-slide.front_sight_width":0.14,"taurus-tx22-toro-slide.guide_rod_d":0.3,"taurus-tx22-toro-slide.guide_rod_y":0.56,"taurus-tx22-toro-slide.height":0.514,"taurus-tx22-toro-slide.length":6.929,"taurus-tx22-toro-slide.lug_bottom":0.826,"taurus-tx22-toro-slide.lug_length":0.27,"taurus-tx22-toro-slide.lug_width":0.532,"taurus-tx22-toro-slide.nose_bevel_across":23,"taurus-tx22-toro-slide.nose_bevel_front_y":0.151,"taurus-tx22-toro-slide.nose_bevel_rear_y":0.274,"taurus-tx22-toro-slide.nose_rear_x":4.263,"taurus-tx22-toro-slide.plate_edge_break":0.0065,"taurus-tx22-toro-slide.plate_width_inset":0,"taurus-tx22-toro-slide.port_floor":0.09,"taurus-tx22-toro-slide.ramp1_bevel_front":0.016,"taurus-tx22-toro-slide.ramp1_bevel_rear":0.053,"taurus-tx22-toro-slide.ramp1_rear_x":2.084,"taurus-tx22-toro-slide.ramp2_bevel_front":0.024,"taurus-tx22-toro-slide.ramp2_bevel_rear":0.057,"taurus-tx22-toro-slide.ramp2_rear_x":1.709,"taurus-tx22-toro-slide.ramp3_bevel_front":0.027,"taurus-tx22-toro-slide.ramp3_bevel_rear":0.048,"taurus-tx22-toro-slide.ramp3_rear_x":1.5,"taurus-tx22-toro-slide.ramp4_bevel_front":0.046,"taurus-tx22-toro-slide.ramp4_bevel_rear":0.065,"taurus-tx22-toro-slide.ramp4_front_x":1.168,"taurus-tx22-toro-slide.ramp4_rear_x":0.946,"taurus-tx22-toro-slide.rear_block_front_x":3.02,"taurus-tx22-toro-slide.rear_end":0.12,"taurus-tx22-toro-slide.rear_notch_depth":0.07,"taurus-tx22-toro-slide.rear_notch_width":0.12,"taurus-tx22-toro-slide.rear_sight_width":0.6,"taurus-tx22-toro-slide.right_window_front_x":5.39,"taurus-tx22-toro-slide.right_window_rear_x":4.46,"taurus-tx22-toro-slide.screw_head_d":0.17,"taurus-tx22-toro-slide.screw_hole_d":0.1,"taurus-tx22-toro-slide.screw_spacing":0.42,"taurus-tx22-toro-slide.screw_x":1.278,"taurus-tx22-toro-slide.serration_count_front":5,"taurus-tx22-toro-slide.serration_count_rear":7,"taurus-tx22-toro-slide.serration_depth":0.035,"taurus-tx22-toro-slide.top_chamfer":0.07,"taurus-tx22-toro-slide.top_window_front_x":6.21,"taurus-tx22-toro-slide.top_window_rear_x":4.5,"taurus-tx22-toro-slide.top_window_width":0.38,"taurus-tx22-toro-slide.underside_depth":0.22,"taurus-tx22-toro-slide.wall":0.09,"taurus-tx22-toro-slide.width":0.93,"taurus-tx22-toro-slide.window_depth":0.3},"profiles":{"side":[[-0.049,-0.293],[6.925,-0.304],[6.929,0.426],[6.917,0.471],[6.876,0.512],[6.692,0.518],[4.364,0.515],[4.279,0.417],[4.26,0.379],[4.26,0.29],[4.184,0.17],[4.104,0.079],[4.016,0.022],[3.94,0.003],[3.13,0.004],[3.051,0.058],[3.013,0.127],[2.988,0.254],[2.988,0.374],[3.007,0.387],[3.02,0.444],[2.954,0.523],[2.536,0.523],[2.517,0.441],[0.834,0.443],[0.822,0.525],[0.126,0.532],[0.098,0.517],[0.072,0.403]]},"features":{"side":{"front_sight":[[[6.692,0.515],[6.661,0.578],[6.623,0.604],[6.401,0.629],[6.351,0.604],[6.338,0.515]]],"rear_sight":[[[0.544,0.51],[0.493,0.693],[0.367,0.693],[0.303,0.51]]],"cover_plate":[[[2.504,0.438],[2.504,0.526],[2.479,0.539],[2.34,0.539],[2.1,0.521],[2.081,0.54],[1.992,0.537],[1.72,0.527],[1.701,0.54],[1.379,0.54],[1.322,0.553],[1.265,0.553],[1.17,0.541],[0.961,0.528],[0.942,0.544],[0.898,0.547],[0.847,0.522],[0.841,0.44]]],"cover_screws":[[[1.341,0.566],[1.214,0.566],[1.214,0.541],[1.341,0.54]],[[0.955,0.56],[0.879,0.56],[0.879,0.535],[0.955,0.535]]],"left_window":[[[5.439,0.232],[4.269,0.233],[4.218,0.202],[4.193,0.113],[4.205,0.018],[4.25,-0.039],[5.249,-0.04],[5.3,0.011]]],"front_lug":[[[6.919,-0.308],[6.843,-0.307],[6.842,-0.826],[6.918,-0.826]]],"front_serrations":[[[6.56,0.186],[6.434,0.186],[6.228,-0.155],[6.355,-0.155]],[[6.358,0.187],[6.231,0.187],[6.026,-0.155],[6.152,-0.155]],[[6.155,0.187],[6.029,0.187],[5.823,-0.154],[5.95,-0.155]],[[5.953,0.187],[5.826,0.187],[5.621,-0.154],[5.747,-0.154]],[[5.75,0.187],[5.624,0.187],[5.419,-0.154],[5.545,-0.154]]],"rear_serrations":[[[1.949,0.375],[1.81,0.375],[1.465,-0.238],[1.604,-0.238]],[[1.74,0.376],[1.601,0.376],[1.256,-0.237],[1.395,-0.238]],[[1.531,0.376],[1.392,0.376],[1.047,-0.237],[1.187,-0.237]],[[1.326,0.376],[1.187,0.376],[0.842,-0.237],[0.981,-0.237]],[[1.114,0.376],[0.975,0.376],[0.63,-0.237],[0.769,-0.237]],[[0.905,0.377],[0.766,0.377],[0.421,-0.236],[0.56,-0.237]],[[0.696,0.377],[0.557,0.377],[0.212,-0.236],[0.352,-0.236]]]}},"placement":{"side":{"plane":"xy","offset":{}}},"bounds":{"min":[0.8224,0.3,-0.465],"max":[2.5367,0.565,0.465]},"volume_in3":0.1465,"centroid":[1.6567,0.4854,0],"shell":[1.6488,0.4838,0],"area_in2":3.7565,"triangles":704,"manifold":true,"slabs":[[0.822,0.439,-0.465,1.165,0.547,0.465],[1.165,0.3,-0.465,1.508,0.565,0.465],[1.508,0.439,-0.465,2.537,0.54,0.465]],"slots":["cover","screws"]},"toolcraft-556-bcg":{"part":"toolcraft-556-bcg","model":"toolcraft-556-bcg.glb","script":"mil_spec_bolt_carrier_groups.py","inputs":{"std.ar15.carrier_body_od":0.93,"std.ar15.carrier_bolt_body_d":0.528,"std.ar15.carrier_bolt_cam_hole_to_face":1.305,"std.ar15.carrier_bolt_face_from_rear":2.675,"std.ar15.carrier_bolt_face_recess_d":0.38,"std.ar15.carrier_bolt_head_d":0.55,"std.ar15.carrier_bolt_length":2.8,"std.ar15.carrier_bolt_lug_length":0.278,"std.ar15.carrier_bolt_lug_od":0.743,"std.ar15.carrier_bolt_lug_offset":67.5,"std.ar15.carrier_bolt_lug_pitch":45,"std.ar15.carrier_bolt_lug_root_d":0.53,"std.ar15.carrier_bolt_lug_slot_width":0.102,"std.ar15.carrier_bolt_lugs":7,"std.ar15.carrier_bottom_cut_depth":0.215,"std.ar15.carrier_bottom_cut_rear":5.0965,"std.ar15.carrier_bottom_cut_rear_r":0.125,"std.ar15.carrier_cam_advance":0.255,"std.ar15.carrier_cam_advance_20":0.195,"std.ar15.carrier_cam_angle":22.5,"std.ar15.carrier_cam_dwell":0.042,"std.ar15.carrier_cam_pin_d":0.3105,"std.ar15.carrier_cam_pin_head_corner_d":0.47,"std.ar15.carrier_cam_pin_head_height":0.095,"std.ar15.carrier_cam_pin_head_length":0.32,"std.ar15.carrier_cam_pin_head_width":0.401,"std.ar15.carrier_cam_pin_hole_to_head":0.507,"std.ar15.carrier_cam_tail":0.07,"std.ar15.carrier_cam_width":0.3165,"std.ar15.carrier_cam_x":0.64,"std.ar15.carrier_cut_corner_r":0.12,"std.ar15.carrier_front_chamfer":0.075,"std.ar15.carrier_front_chamfer_angle":45,"std.ar15.carrier_front_flat_drop":0.095,"std.ar15.carrier_groove_angle":45,"std.ar15.carrier_groove_r":0.078,"std.ar15.carrier_groove_runout_from_shoulder":2.35,"std.ar15.carrier_groove_runout_r":1.5,"std.ar15.carrier_key_base_height":0.241,"std.ar15.carrier_key_bore_d":0.1805,"std.ar15.carrier_key_bore_depth":0.82,"std.ar15.carrier_key_cbore_d":0.273,"std.ar15.carrier_key_foot_length":1.31,"std.ar15.carrier_key_length":2.465,"std.ar15.carrier_key_mouth_angle":60,"std.ar15.carrier_key_mouth_d":0.225,"std.ar15.carrier_key_ramp_angle":45,"std.ar15.carrier_key_ramp_top":1.26,"std.ar15.carrier_key_screw_from_front":1.765,"std.ar15.carrier_key_screw_head_d":0.266,"std.ar15.carrier_key_screw_head_h":0.159,"std.ar15.carrier_key_screw_socket":0.125,"std.ar15.carrier_key_screw_socket_depth":0.077,"std.ar15.carrier_key_screw_spacing":0.5,"std.ar15.carrier_key_screw_x":2.055,"std.ar15.carrier_key_seat_front":1.37,"std.ar15.carrier_key_seat_rear":2.74,"std.ar15.carrier_key_seat_runout_r":0.5,"std.ar15.carrier_key_seat_y":0.42,"std.ar15.carrier_key_slot_width":0.4035,"std.ar15.carrier_key_step":0.03,"std.ar15.carrier_key_step_height":0.182,"std.ar15.carrier_key_tube_axis_y":0.361,"std.ar15.carrier_key_tube_d":0.25,"std.ar15.carrier_key_tube_length":0.9,"std.ar15.carrier_key_width":0.4005,"std.ar15.carrier_length":6.672,"std.ar15.carrier_pad_edge_angle":55,"std.ar15.carrier_pad_front":0.38,"std.ar15.carrier_rail_od":0.994,"std.ar15.carrier_rail_top_drop":0.67,"std.ar15.carrier_rear_chamfer":0.03,"std.ar15.carrier_rear_chamfer_angle":30,"std.ar15.carrier_relief_angle":75,"std.ar15.carrier_retaining_pin_csk_angle":82,"std.ar15.carrier_retaining_pin_csk_d":0.281,"std.ar15.carrier_retaining_pin_hole_d":0.093,"std.ar15.carrier_retaining_pin_x":2.536,"std.ar15.carrier_retaining_pin_y":0.157,"std.ar15.carrier_rib_bottom_drop":0.859,"std.ar15.carrier_rib_chamfer_across":0.87,"std.ar15.carrier_rib_chamfer_angle":22.5,"std.ar15.carrier_rib_rear":2.81,"std.ar15.carrier_rib_taper_angle":4.5,"std.ar15.carrier_rib_taper_start":1.8,"std.ar15.carrier_rib_width":0.399,"std.ar15.carrier_scallop_across":0.8125,"std.ar15.carrier_scallop_angle":22.5,"std.ar15.carrier_scallop_flat":0.375,"std.ar15.carrier_scallop_r":0.47,"std.ar15.carrier_scallop_rear":1.5,"std.ar15.carrier_serration_count":28,"std.ar15.carrier_serration_cutter_r":0.3125,"std.ar15.carrier_serration_depth":0.042,"std.ar15.carrier_serration_face_angle":70.5,"std.ar15.carrier_serration_flank_angle":22.25,"std.ar15.carrier_serration_front":1.9,"std.ar15.carrier_serration_pitch":0.125,"std.ar15.carrier_side_hole_d":0.125,"std.ar15.carrier_side_hole_x":2.15,"std.ar15.carrier_slab_height":0.5,"std.ar15.carrier_slot_travel":1.75,"std.ar15.carrier_slot_width":0.5,"std.ar15.carrier_tail_bore":0.625,"std.ar15.carrier_tail_front":5.1,"std.ar15.carrier_tail_notch_depth":0.1,"std.ar15.carrier_tail_notch_width":0.156,"std.ar15.carrier_top_cut_length":2.07,"std.ar15.carrier_vent_angle":45,"std.ar15.carrier_vent_d":0.109,"std.ar15.carrier_vent_x":1.34,"toolcraft-556-bcg.length":6.672,"toolcraft-556-bcg.od":0.994},"profiles":{},"bounds":{"min":[0,-0.4583,-0.4659],"max":[7.462,0.906,0.4659]},"volume_in3":2.9018,"centroid":[4.1793,0.0669,-0.0073],"shell":[3.7848,0.0999,0.0007],"area_in2":33.6114,"triangles":20152,"manifold":true,"slabs":[[0,-0.458,-0.465,1.964,0.465,0.465],[1.964,-0.25,-0.465,3.535,0.252,0.465],[3.535,-0.349,-0.466,4.713,0.661,0.466],[4.713,-0.362,-0.466,6.677,0.906,0.466],[6.677,-0.275,-0.275,7.069,0.275,0.275],[7.069,-0.368,-0.368,7.462,0.368,0.368]],"slots":["body","screws"]},"unity-fast-micro-226":{"part":"unity-fast-micro-226","model":"unity-fast-micro-226.glb","script":"unity_fast_micro.py","inputs":{"std.density.aluminium_7075":1.632,"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.top_width":0.835,"unity-fast-micro-226.band_below_top":1.514,"unity-fast-micro-226.band_outer_z":0.654,"unity-fast-micro-226.bolt_above_feet":0.255,"unity-fast-micro-226.bolt_counterbore_d":0.34,"unity-fast-micro-226.bolt_head_d":0.27,"unity-fast-micro-226.cross_bolt_spacing":1.584,"unity-fast-micro-226.deck_above_rail":1.671,"unity-fast-micro-226.deck_channel_depth":0.05,"unity-fast-micro-226.deck_opening_length":0.32,"unity-fast-micro-226.deck_opening_width":0.42,"unity-fast-micro-226.deck_rim_width":0.09,"unity-fast-micro-226.deck_x":0,"unity-fast-micro-226.drum_below_top":0.629,"unity-fast-micro-226.drum_d":0.32,"unity-fast-micro-226.drum_relief_d":0.46,"unity-fast-micro-226.edge_break":0.011,"unity-fast-micro-226.end_window_bottom_below_top":1.36,"unity-fast-micro-226.end_window_top_below_top":0.77,"unity-fast-micro-226.end_window_width":0.57,"unity-fast-micro-226.front_pocket_x0":0.616,"unity-fast-micro-226.front_pocket_x1":0.896,"unity-fast-micro-226.front_post_d":0.06,"unity-fast-micro-226.front_post_x":0.917,"unity-fast-micro-226.grabber_bottom_below_top":1.97,"unity-fast-micro-226.grabber_length":1.9,"unity-fast-micro-226.grabber_top_below_top":1.48,"unity-fast-micro-226.lever_hole_d":0.24,"unity-fast-micro-226.lever_recess_af":0.39,"unity-fast-micro-226.lug_length":0.22,"unity-fast-micro-226.lug_width":0.3,"unity-fast-micro-226.oval_x0":-0.118,"unity-fast-micro-226.oval_x1":0.51,"unity-fast-micro-226.pocket_bottom_below_top":1.199,"unity-fast-micro-226.pocket_top_below_top":0.615,"unity-fast-micro-226.rear_aperture_d":0.2,"unity-fast-micro-226.rear_aperture_hole_d":0.06,"unity-fast-micro-226.rear_aperture_length":0.12,"unity-fast-micro-226.rear_pocket_x0":-0.896,"unity-fast-micro-226.rear_pocket_x1":-0.456,"unity-fast-micro-226.rear_sight_height":1.42,"unity-fast-micro-226.rear_sight_x":-0.353,"unity-fast-micro-226.relief_depth":0.025,"unity-fast-micro-226.small_hole_above_feet":0.305,"unity-fast-micro-226.small_hole_d":0.108,"unity-fast-micro-226.small_hole_spacing":0.612,"unity-fast-micro-226.top_width":0.91,"unity-fast-micro-226.tunnel_bottom_below_top":0.494,"unity-fast-micro-226.tunnel_top_below_top":0.171,"unity-fast-micro-226.tunnel_width":0.56,"unity-fast-micro-226.wall_width":0.85,"unity-fast-micro-226.window_bottom_below_top":1.45,"unity-fast-micro-226.window_chamfer_below_top":1.147,"unity-fast-micro-226.window_chamfer_x":-0.033,"unity-fast-micro-226.window_corner_r":0.08,"unity-fast-micro-226.window_top_below_top":0.651,"unity-fast-micro-226.window_x0":-0.499,"unity-fast-micro-226.window_x1":0.505},"profiles":{"side":[[-1.035,-0.252],[-1.027,-1.865],[-0.995,-1.933],[-0.942,-1.987],[-0.9,-2.012],[-0.87,-2.02],[-0.714,-2.02],[0.884,-2.014],[0.95,-1.977],[1.024,-1.889],[1.035,-1.827],[1.035,-1.695],[1.024,-0.86],[1.028,-0.072],[1.022,-0.042],[0.997,-0.016],[0.948,0],[0.31,0],[0,-0.002],[-0.973,-0.005],[-1.012,-0.027],[-1.033,-0.052]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{"y":"deck_above_rail"}}},"bounds":{"min":[-1.045,-0.349,-0.654],"max":[1.045,1.671,0.654]},"volume_in3":1.8969,"centroid":[-0.0175,0.5943,0.0008],"shell":[-0.0097,0.648,0.0062],"area_in2":25.9302,"triangles":10006,"manifold":true,"rail_seat":{"x":[-1.045,1.045],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-1.045,-0.349,-0.654,1.045,1.671,0.654]],"slots":["body","hardware"]},"vg6-gamma-556":{"part":"vg6-gamma-556","model":"vg6-gamma-556.glb","script":"vg6_gamma_556.py","inputs":{"vg6-gamma-556.bore_d":0.27,"vg6-gamma-556.bottom_slot_front_front_x":1.608,"vg6-gamma-556.bottom_slot_front_rear_x":1.273,"vg6-gamma-556.bottom_slot_inner_z":0.133,"vg6-gamma-556.bottom_slot_outer_z":0.272,"vg6-gamma-556.bottom_slot_rear_front_x":1.136,"vg6-gamma-556.bottom_slot_rear_rear_x":0.76,"vg6-gamma-556.bottom_slot_rear_z":0.206,"vg6-gamma-556.bottom_slot_width":0.055,"vg6-gamma-556.bottom_slots":6,"vg6-gamma-556.flats_across":0.738,"vg6-gamma-556.front_chamfer":0.02,"vg6-gamma-556.front_port_front_x":1.62,"vg6-gamma-556.front_port_height":0.577,"vg6-gamma-556.front_port_rear_x":1.274,"vg6-gamma-556.groove_1_d":0.786,"vg6-gamma-556.groove_1_front_x":0.622,"vg6-gamma-556.groove_1_rear_x":0.489,"vg6-gamma-556.groove_2_d":0.703,"vg6-gamma-556.groove_2_front_x":0.375,"vg6-gamma-556.groove_2_rear_x":0.258,"vg6-gamma-556.length":1.935,"vg6-gamma-556.lobe_depth":0.12,"vg6-gamma-556.lobe_reach":0.2,"vg6-gamma-556.od":0.86,"vg6-gamma-556.overall_length":1.83,"vg6-gamma-556.port_corner_r":0.09,"vg6-gamma-556.rear_chamfer":0.02,"vg6-gamma-556.rear_hole_d":0.108,"vg6-gamma-556.rear_hole_depth":0.12,"vg6-gamma-556.rear_hole_x":0.119,"vg6-gamma-556.rear_port_front_x":1.149,"vg6-gamma-556.rear_port_height":0.631,"vg6-gamma-556.rear_port_rear_x":0.754,"vg6-gamma-556.side_ports":2,"vg6-gamma-556.slot_floor_y":0.11,"vg6-gamma-556.slot_length":0.718,"vg6-gamma-556.slot_width":0.263,"vg6-gamma-556.thread_depth":0.6,"vg6-gamma-556.thread_major_d":0.4957,"vg6-gamma-556.thread_minor_d":0.4551,"vg6-gamma-556.thread_pitch":0.03571,"vg6-gamma-556.top_hole_1_x":1.578,"vg6-gamma-556.top_hole_2_x":1.5,"vg6-gamma-556.top_hole_3_x":1.421,"vg6-gamma-556.top_hole_d":0.052,"vg6-gamma-556.top_hole_inner_z":0.215,"vg6-gamma-556.top_hole_outer_z":0.272,"vg6-gamma-556.top_holes":6,"vg6-gamma-556.washer_id":0.5,"vg6-gamma-556.washer_od":0.728,"vg6-gamma-556.washer_thickness":0.105},"profiles":{},"bounds":{"min":[0,-0.43,-0.43],"max":[1.935,0.43,0.43]},"volume_in3":0.4976,"centroid":[0.916,-0.0183,0],"shell":[0.9068,-0.0083,-0.0001],"area_in2":10.3657,"triangles":26008,"manifold":true,"slabs":[[0,-0.43,-0.369,1.161,0.43,0.369],[1.161,-0.43,-0.43,1.935,0.43,0.43]],"slots":["body","washer"]},"vltor-a5-buffer-spring":{"part":"vltor-a5-buffer-spring","model":"vltor-a5-buffer-spring.glb","script":"vltor_a5_buffer_spring.py","inputs":{"std.carbine_buffer.head_thickness":0.254,"std.carbine_buffer.pilot_d":0.781,"std.receiver_extension.bore_d":1,"vltor-a5-buffer-spring.coils":44,"vltor-a5-buffer-spring.free_length":12.5,"vltor-a5-buffer-spring.installed_length":7.66,"vltor-a5-buffer-spring.od":0.94,"vltor-a5-buffer-spring.solid_length":3.285,"vltor-a5-buffer-spring.wire_d":0.072},"profiles":{},"bounds":{"min":[0.254,-0.4719,-0.4719],"max":[7.914,0.4719,0.4719]},"volume_in3":0.4864,"centroid":[4.084,0,0],"shell":[4.084,0.0001,0],"area_in2":27.7923,"triangles":19724,"manifold":true,"slabs":[[0.254,-0.472,-0.472,7.914,0.472,0.472]],"slots":["spring"]},"vltor-a5-receiver-extension":{"part":"vltor-a5-receiver-extension","model":"vltor-a5-receiver-extension.glb","script":"vltor_a5_receiver_extension.py","inputs":{"std.receiver_extension.bore_d":1,"std.receiver_extension.carbine_vent_d":0.094,"std.receiver_extension.rail_bottom_below_axis":0.874,"std.receiver_extension.rail_width":0.49,"std.receiver_extension.thread_major_d":1.1813,"std.receiver_extension.thread_minor_d":1.1093,"std.receiver_extension.thread_pitch":0.0625,"vltor-a5-receiver-extension.channel_depth":0.08,"vltor-a5-receiver-extension.channel_front_from_rear":4.64,"vltor-a5-receiver-extension.channel_rear_from_rear":0.35,"vltor-a5-receiver-extension.channel_width":0.25,"vltor-a5-receiver-extension.position_hole_d":0.3,"vltor-a5-receiver-extension.position_hole_rear_from_rear":0.63,"vltor-a5-receiver-extension.position_step":0.65,"vltor-a5-receiver-extension.rail_lip_depth":0.04,"vltor-a5-receiver-extension.rail_ramp_end":2.8,"vltor-a5-receiver-extension.rail_ramp_start":2.33,"vltor-a5-receiver-extension.rear_edge_round":0.04,"vltor-a5-receiver-extension.rear_wall":0.072,"vltor-a5-receiver-extension.relief_d":1.123,"vltor-a5-receiver-extension.relief_end":1.51,"vltor-a5-receiver-extension.thread_length":1.1,"vltor-a5-receiver-extension.tube_front_behind_pin":0.669,"vltor-a5-receiver-extension.tube_length":7.9375,"vltor-a5-receiver-extension.tube_od":1.148},"profiles":{},"bounds":{"min":[0.669,-0.874,-0.5907],"max":[8.6065,0.5907,0.5907]},"volume_in3":2.6792,"centroid":[5.0213,-0.1742,0],"shell":[4.7423,-0.0809,0],"area_in2":63.5466,"triangles":30860,"manifold":true,"slabs":[[0.669,-0.642,-0.591,3.05,0.591,0.591],[3.05,-0.874,-0.574,8.606,0.574,0.574]],"slots":["tube"]},"vltor-a5h2-buffer":{"part":"vltor-a5h2-buffer","model":"vltor-a5h2-buffer.glb","script":"vltor_a5h2_buffer.py","inputs":{"std.carbine_buffer.body_d":0.687,"std.carbine_buffer.body_start":0.5145,"std.carbine_buffer.bumper_band":0.06,"std.carbine_buffer.bumper_d":0.687,"std.carbine_buffer.bumper_exposed":0.4,"std.carbine_buffer.bumper_taper":13.5,"std.carbine_buffer.head_flat_across":0.952,"std.carbine_buffer.head_rim":0.214,"std.carbine_buffer.head_thickness":0.254,"std.carbine_buffer.length":3.251,"std.carbine_buffer.pilot_d":0.781,"std.carbine_buffer.pilot_end":0.468,"std.carbine_buffer.pin_d":0.122,"vltor-a5h2-buffer.body_length":3.3,"vltor-a5h2-buffer.length":3.7,"vltor-a5h2-buffer.od":0.98,"vltor-a5h2-buffer.pin_from_open_end":0.19},"profiles":{},"bounds":{"min":[0,-0.49,-0.49],"max":[3.7,0.462,0.49]},"volume_in3":1.46,"centroid":[1.6846,0,0],"shell":[1.8263,0,0],"area_in2":10.6265,"triangles":7276,"manifold":true,"slabs":[[0,-0.49,-0.49,0.37,0.462,0.49],[0.37,-0.391,-0.391,3.7,0.391,0.391]],"slots":["body","bumper","pin"]},"vltor-castle-nut":{"part":"vltor-castle-nut","model":"vltor-castle-nut.glb","script":"vltor_castle_nut.py","inputs":{"std.receiver_extension.thread_major_d":1.1813,"vltor-castle-nut.edge_break":0.012,"vltor-castle-nut.notch_depth":0.112,"vltor-castle-nut.notch_width":0.123,"vltor-castle-nut.notches":4,"vltor-castle-nut.od":1.363,"vltor-castle-nut.thickness":0.334},"profiles":{},"bounds":{"min":[0,-0.6815,-0.6815],"max":[0.334,0.6815,0.6815]},"volume_in3":0.1162,"centroid":[0.1622,0,0],"shell":[0.1644,0,0],"area_in2":3.3385,"triangles":3568,"manifold":true,"slabs":[[0,-0.682,-0.59,0.334,-0.341,0.59],[0,-0.341,-0.682,0.334,0.341,0.682],[0,0.341,-0.59,0.334,0.682,0.59]],"slots":["nut"]},"vltor-lockplate":{"part":"vltor-lockplate","model":"vltor-lockplate.glb","script":"vltor_lockplate.py","inputs":{"std.receiver_extension.key_slot_floor":0.55,"std.receiver_extension.key_slot_width":0.125,"std.receiver_extension.thread_major_d":1.1813,"vltor-lockplate.boss_below_axis":0.9974,"vltor-lockplate.boss_height":0.375,"vltor-lockplate.boss_proud":0.0645,"vltor-lockplate.boss_width":0.496,"vltor-lockplate.corner_angle":31.33,"vltor-lockplate.dimple_depth":0.063,"vltor-lockplate.dimple_grow":0.005,"vltor-lockplate.edge_break":0.012,"vltor-lockplate.hole_d":1.1902,"vltor-lockplate.key_tip_below_axis":0.5619,"vltor-lockplate.key_width":0.125,"vltor-lockplate.lobe_centre_below_axis":0.9522,"vltor-lockplate.lobe_radius":0.4266,"vltor-lockplate.relief_bottom_below_axis":0.6575,"vltor-lockplate.relief_fillet_r":0.031,"vltor-lockplate.relief_floor_half_width":0.1119,"vltor-lockplate.relief_top_half_width":0.354,"vltor-lockplate.side_angle":13.5,"vltor-lockplate.thickness":0.124,"vltor-lockplate.top_above_axis":0.6817},"profiles":{},"bounds":{"min":[-0.0645,-1.3788,-0.6816],"max":[0.124,0.6817,0.6816]},"volume_in3":0.1191,"centroid":[0.0515,-0.5977,0.0003],"shell":[0.0541,-0.4761,0.0004],"area_in2":3.2758,"triangles":3460,"manifold":true,"slabs":[[-0.064,-1.379,-0.419,0.124,-1.035,0.419],[-0.064,-1.035,-0.501,0.124,-0.692,0.501],[0,-0.692,-0.586,0.124,-0.349,0.586],[0,-0.349,-0.682,0.124,0.338,0.682],[0,0.338,-0.592,0.124,0.682,0.592]],"slots":["plate"]},"vortex-sport-cantilever-30mm-mount":{"part":"vortex-sport-cantilever-30mm-mount","model":"vortex-sport-cantilever-30mm-mount.glb","script":"vortex_sport_cantilever_30mm_mount.py","inputs":{"std.picatinny.bevel_gauge_apart":0.108,"std.picatinny.bevel_width":0.748,"std.picatinny.lower_gauge_below_top":0.154,"std.picatinny.slot_depth":0.118,"std.picatinny.slot_width":0.206,"std.picatinny.top_width":0.835,"vortex-sport-cantilever-30mm-mount.arm_chamfer_left":0.075,"vortex-sport-cantilever-30mm-mount.arm_chamfer_right":0.025,"vortex-sport-cantilever-30mm-mount.arm_top_left_z":-0.032,"vortex-sport-cantilever-30mm-mount.arm_top_right_z":0.19,"vortex-sport-cantilever-30mm-mount.arm_width":0.322,"vortex-sport-cantilever-30mm-mount.base_left_z":0.43,"vortex-sport-cantilever-30mm-mount.base_middle_half_width":0.27,"vortex-sport-cantilever-30mm-mount.base_right_z":0.637,"vortex-sport-cantilever-30mm-mount.base_top_y":0.316,"vortex-sport-cantilever-30mm-mount.cap_pocket_d":0.32,"vortex-sport-cantilever-30mm-mount.cap_screw_head_above_axis":0.255,"vortex-sport-cantilever-30mm-mount.cap_screw_spacing":0.39,"vortex-sport-cantilever-30mm-mount.cap_screw_z":0.762,"vortex-sport-cantilever-30mm-mount.clamp_face_below_rail_top":0.065,"vortex-sport-cantilever-30mm-mount.clamp_front_reach":1.807,"vortex-sport-cantilever-30mm-mount.clamp_length":0.73,"vortex-sport-cantilever-30mm-mount.clamp_outer_z":0.625,"vortex-sport-cantilever-30mm-mount.clamp_rear_reach":1.34,"vortex-sport-cantilever-30mm-mount.clamp_screw_head_under_face":0.01,"vortex-sport-cantilever-30mm-mount.clamp_screw_spacing":0.325,"vortex-sport-cantilever-30mm-mount.clamp_screw_y":0.135,"vortex-sport-cantilever-30mm-mount.clamp_top_y":0.305,"vortex-sport-cantilever-30mm-mount.edge_break":0.006,"vortex-sport-cantilever-30mm-mount.front_clamp_front_x":1.791,"vortex-sport-cantilever-30mm-mount.front_jaw_length":0.822,"vortex-sport-cantilever-30mm-mount.front_jaw_top_y":0.259,"vortex-sport-cantilever-30mm-mount.jaw_bottom_below_rail_top":0.233,"vortex-sport-cantilever-30mm-mount.jaw_foot_chamfer":0.065,"vortex-sport-cantilever-30mm-mount.lug_half_width":0.27,"vortex-sport-cantilever-30mm-mount.lug_length":0.192,"vortex-sport-cantilever-30mm-mount.lug_spacing":0.394,"vortex-sport-cantilever-30mm-mount.optical_axis_above_rail":1.5,"vortex-sport-cantilever-30mm-mount.rear_clamp_front_x":0.573,"vortex-sport-cantilever-30mm-mount.rear_jaw_length":0.763,"vortex-sport-cantilever-30mm-mount.ring_bore":1.1811023622047243,"vortex-sport-cantilever-30mm-mount.ring_edge_bevel":0.022,"vortex-sport-cantilever-30mm-mount.ring_foot_below_axis":0.745,"vortex-sport-cantilever-30mm-mount.ring_front_x":3.611,"vortex-sport-cantilever-30mm-mount.ring_length":0.735,"vortex-sport-cantilever-30mm-mount.ring_rear_x":0.186,"vortex-sport-cantilever-30mm-mount.ring_side_flat_above_split":0.15,"vortex-sport-cantilever-30mm-mount.ring_side_flat_below_split":0.115,"vortex-sport-cantilever-30mm-mount.ring_split_depth":0.02,"vortex-sport-cantilever-30mm-mount.ring_split_gap":0.014,"vortex-sport-cantilever-30mm-mount.ring_top_above_axis":0.689,"vortex-sport-cantilever-30mm-mount.ring_top_flat_width":0.76,"vortex-sport-cantilever-30mm-mount.ring_width":1.85,"vortex-sport-cantilever-30mm-mount.screw_counterbore_d":0.23,"vortex-sport-cantilever-30mm-mount.screw_head_d":0.21,"vortex-sport-cantilever-30mm-mount.screw_socket_depth":0.02,"vortex-sport-cantilever-30mm-mount.stem_width":0.81,"vortex-sport-cantilever-30mm-mount.thread_window_d":0.065},"profiles":{"side":[[-1.343,0.026],[-1.334,0.018],[2.361,0.002],[2.41,0.035],[2.492,0.051],[2.541,0.083],[2.622,0.099],[2.671,0.131],[2.753,0.147],[2.802,0.179],[2.932,0.211],[2.981,0.244],[3.014,0.244],[3.063,0.276],[3.193,0.308],[3.242,0.34],[3.291,0.34],[3.307,0.356],[3.698,0.355],[3.714,0.371],[3.763,0.371],[3.779,0.387],[3.812,0.387],[3.861,0.419],[3.894,0.419],[3.959,0.451],[4,0.508],[4.001,0.834],[3.993,0.842],[3.244,0.845],[3.236,0.804],[3.179,0.748],[3.146,0.748],[3.015,0.683],[2.934,0.667],[2.885,0.635],[2.804,0.619],[2.755,0.587],[2.673,0.571],[2.624,0.538],[2.543,0.522],[2.494,0.49],[2.412,0.474],[2.363,0.442],[2.282,0.426],[2.216,0.394],[1.24,0.398],[1.223,0.382],[0.979,0.383],[0.963,0.399],[0.898,0.399],[0.881,0.416],[0.849,0.416],[0.67,0.514],[0.638,0.514],[0.597,0.555],[0.565,0.621],[0.558,0.857],[-0.159,0.86],[-0.168,0.607],[-0.201,0.575],[-0.201,0.559],[-0.258,0.518],[-0.454,0.421],[-0.486,0.422],[-0.519,0.389],[-0.551,0.389],[-0.666,0.325],[-1.333,0.328]]},"features":{"side":{}},"placement":{"side":{"plane":"xy","offset":{}}},"bounds":{"min":[-1.34,-0.233,-0.925],"max":[3.9785,2.189,0.925]},"axis_y":1.5,"volume_in3":2.9382,"centroid":[1.2952,0.7683,0.0153],"shell":[1.3508,0.898,-0.0176],"area_in2":35.8767,"triangles":6600,"manifold":true,"rail_seat":{"x":[-1.34,1.807],"top_y":0,"centre_z":0,"to_y":-0.154,"reach":0.4525},"slabs":[[-1.34,-0.233,-0.625,-0.58,0.362,0.637],[-0.58,-0.232,-0.625,-0.2,0.56,0.636],[-0.2,-0.118,-0.925,0.559,2.189,0.925],[0.559,0,-0.27,0.939,0.808,0.27],[0.939,-0.233,-0.625,2.079,0.393,0.637],[2.079,0,-0.107,2.459,0.483,0.215],[2.459,0.038,-0.107,2.839,0.623,0.215],[2.839,0.184,-0.107,3.219,0.787,0.215],[3.219,0.331,-0.925,3.978,2.189,0.925]],"slots":["body","hardware"]}},"vendors":{"magpul":{"label":"Magpul","url":"https://magpul.com","kind":"manufacturer","shipping":{"free_over":99,"flat":5.99,"from":false,"source":{"url":"https://magpul.com/shipping-and-returns","stated":"orders with a product total over $99 will ship for free. We charge a $5.99 flat rate for shipping. All packages for continental U.S. addresses are shipped via FedEX","retrieved":"2026-10-02"},"note":"\"over $99\": a total of exactly $99 may not qualify; taken as the threshold."}},"battle-arms":{"label":"Battle Arms Development","url":"https://battlearmsdevelopment.com","kind":"manufacturer","shipping":{"free_over":null,"flat":null,"from":false,"ffl":{"ships":true,"charge":null,"from":false,"excluded":false,"stated":"IF an order is for a serialized item or firearm the system will dictate it as such and it will be sent to the chosen FFL."},"source":{"url":"https://battlearmsdevelopment.com/store-policies","stated":"Our Flat rate shipping policy only qualifies for the lower 48 states.","retrieved":"2026-10-02"},"note":"A flat rate exists; its amount isn't on the page."}},"palmetto-state-armory":{"label":"Palmetto State Armory","url":"https://palmettostatearmory.com","kind":"manufacturer"},"nordic":{"label":"Nordic Components","url":"https://nordiccomp.com","kind":"manufacturer","shipping":{"free_over":199,"flat":8.95,"from":false,"excludes":"Free shipping applies to regular ground shipping ON INTERNET ORDERS ONLY within the 48 contiguous United States. Shipping fees will be added to Alaska and Hawaii orders (call for pricing).","source":{"url":"https://nordiccomp.com/terms-and-conditions/shipping-policy/","stated":"Get free regular ground shipping on all orders over $199! On all orders up to $199, there is a flat rate shipping charge of $8.95 per order.","retrieved":"2026-10-02"}}},"bcm":{"label":"BCM","url":"https://bravocompanyusa.com","kind":"manufacturer","shipping":{"free_over":null,"flat":null,"from":false,"tiers":[{"up_to":100,"rate":6.95},{"up_to":399.99,"rate":9.95},{"up_to":null,"rate":15.95}],"source":{"url":"https://bravocompanyusa.com/shipping-returns/","stated":"$0.00-$100.00: $6.95, USPS Mail; $100.01-$399.99: $9.95 USPS Mail; $400+: $15.95 - UPS Ground. The above shipping rates are only applicable to internet orders.","retrieved":"2026-10-02"},"note":"No free shipping at any order value."}},"holosun":{"label":"Holosun","url":"https://www.holosun.com","kind":"manufacturer","note":"No current shipping-policy page was found on 2026-10-02 (the old Shipping & Returns page is gone; /returns covers warranty returns): rates appear only at checkout."},"larue":{"label":"LaRue Tactical","url":"https://larue.com","kind":"manufacturer","shipping":null,"note":"The terms page (https://larue.com/terms-and-conditions/, 2026-10-02) states no rates or threshold; \"Firearms must be shipped to a licensed FFL dealer where required\"."},"aero-precision":{"label":"Aero Precision","url":"https://www.aeroprecisionusa.com","kind":"manufacturer","shipping":{"free_over":99,"flat":null,"from":false,"ffl":{"ships":true,"charge":null,"from":false,"excluded":false,"stated":"Please expect higher lead times for FFL items."},"source":{"url":"https://www.aeroprecisionusa.com/terms-conditions","stated":"FREE SHIPPING ON ALL ORDERS +$99!","retrieved":"2026-10-02"},"note":"The rate under $99 isn't published. Orders over $500 require a signature."}},"faxon":{"label":"Faxon Firearms","url":"https://faxonfirearms.com","kind":"manufacturer","shipping":null,"note":"The terms page (https://faxonfirearms.com/terms-conditions/, 2026-10-02): \"Shipping and handling charges will apply in addition to the price indicated on the website\", no amounts."},"kak":{"label":"KAK Industry","url":"https://kakindustry.com","kind":"manufacturer","shipping":null,"note":"https://kakindustry.com/shipping-returns/ (2026-10-02): \"the shipping rates for many items we sell are weight-based\", no amounts."},"scalarworks":{"label":"Scalarworks","url":"https://scalarworks.com","kind":"manufacturer","shipping":{"free_over":0,"flat":null,"from":false,"source":{"url":"https://scalarworks.com/shipping/","stated":"We ship mounts and optic bundles via UPS Ground free of charge.","retrieved":"2026-10-13"},"note":"Of mounts and optic bundles, which is all it has on file. The page also says: \"We do not ship internationally directly to end users.\""}},"primary-arms":{"label":"Primary Arms","url":"https://www.primaryarms.com","kind":"retailer","shipping":{"free_over":null,"flat":null,"from":false,"ffl":{"ships":true,"charge":null,"from":false,"excluded":false,"stated":"All firearms, including lower receivers, must ship to 'licensed persons'. (https://www.primaryarms.com/federal-firearms-license)"},"source":{"url":"https://www.primaryarms.com/faq","stated":"All orders ship from our facility in Houston, TX, and we do the best we can to pass the best rates we can achieve on to you. The exact cost of shipping will vary, depending on factors like order size or selected speed.","retrieved":"2026-10-02"},"note":"No standing threshold or rate on the page; sitewide free-shipping promotions exclude handguns (FFL). A sentence about free shipping on orders with a Primary Arms Optics product reached the research only through a search snippet and isn't used."}},"the2ndtactical":{"label":"The 2nd Tactical","url":"https://the2ndtactical.com","kind":"retailer","shipping":null,"note":"Its FAQ (https://the2ndtactical.com/faq/, read 2026-10-18), the one policy page its product pages link to: \"All items will ship by the United States Post Office.\" No rate or threshold. Added for Guntec's buffer tube, which no other seller on file sells alone (catalog batch 12)."},"guntec-usa":{"label":"Guntec USA","url":"https://guntecusa.com","kind":"manufacturer","shipping":null,"note":"The maker's own shop. Its site refuses the reader and is never asked (D59): its prices are read from its product pages as the user saved them from their own browser on 2026-10-19 (references/inbox/guntec/, filed under the tube's references), each offer's `saved:` and `observed:`. No shipping page of it is on file."},"spikes-tactical":{"label":"Spike's Tactical","url":"https://www.spikestactical.com","kind":"manufacturer","shipping":null,"note":"The maker's own shop. Its shipping policy is linked from its pages at a bare IP address, not its own site, and isn't read: no rate or threshold on file. Added for its SDR100A delta ring assembly with its barrel nut, which no other seller on file carries (catalog batch 15)."},"vltor":{"label":"VLTOR","url":"https://vltor.com","kind":"manufacturer","shipping":null,"note":"The maker's own shop. Its terms (https://vltor.com/terms, read 2026-10-28): \"6. Shipping We ship to addresses within the United States.\"; its product pages: \"Shipping within the United States only.\" No rate or threshold. Added for its A5 buffer system, whose buffer, spring and kits no seller on file carries (catalog batch 15)."},"slr-rifleworks":{"label":"SLR Rifleworks","url":"https://slrrifleworks.com","kind":"manufacturer","shipping":null,"note":"The maker's own shop. Its Shipping & Returns page (https://slrrifleworks.com/shipping-returns/, read 2026-10-28 through a page reader's summary): \"We ship our packages using USPS Priority Mail (2-3 Days)\", \"We only ship within the US, no International shipping.\" No rate or threshold. Added for its Sentry 7 gas block (catalog batch 15)."},"wing-tactical":{"label":"Wing Tactical","url":"https://www.wingtactical.com","kind":"retailer","shipping":null,"note":"https://www.wingtactical.com/shipping-returns/ (2026-10-02): \"Customers can view shipping costs and estimated delivery times before finalizing their order at the checkout page.\" No threshold or rate."},"midwayusa":{"label":"MidwayUSA","url":"https://www.midwayusa.com","kind":"retailer","shipping":{"free_over":100,"flat":8,"from":false,"excludes":"Some exclusions apply to clearance products, large or bulky products, products with quantity limits, some firearms, and products that ship alone or directly from a supplier.","ffl":{"ships":true,"charge":10,"from":false,"excluded":false,"stated":"Charge for select rifles, shotguns, and actions/receivers under $500: $10.00 per product"},"source":{"url":"https://www.midwayusa.com/cart/shippingrateinfo","stated":"Free shipping on orders over $100, with low-price, flat-rate shipping on Just About Everything else. Economy $8.00, USPS Priority $14.00, UPS Ground $16.00","retrieved":"2026-10-02"},"note":"Economy is the rate used. Oversize ($5/$15/$25 per product) and remote-location ($20) surcharges aren't applied."}},"midwest-gun-works":{"label":"Midwest Gun Works","url":"https://www.midwestgunworks.com","kind":"retailer","shipping":{"free_over":null,"flat":7.99,"from":true,"ffl":{"ships":true,"charge":30,"from":true,"excluded":false,"stated":"are $30.00 and up on firearm purchases (shipping fees may vary on orders placed over the telephone and can increase due to size and weight). Long Guns: Minimum shipping rate is set at $32.00"},"source":{"url":"https://www.midwestgunworks.com/shipping-policy-order-tracking.html","stated":"Current shipping costs range from $7.99 - $22.99 on all non-firearm purchases","retrieved":"2026-10-02"},"note":"Rates vary with size, weight and destination: the low end of the range is used, marked from."}},"academy":{"label":"Academy Sports + Outdoors","url":"https://www.academy.com","kind":"retailer","note":"Its shipping pages were behind a bot check on 2026-10-02 and weren't read; search snippets (not used) speak of free shipping over $25 to $50 and of firearms for store pickup only."},"scheels":{"label":"Scheels","url":"https://www.scheels.com","kind":"retailer","shipping":{"free_over":75,"flat":9.99,"from":false,"excludes":"Free standard shipping on orders $75 or more applies to Standard shipping only and does not apply to Same Day Delivery, Expedited, Express, or Alaska & Hawaii shipping. Items with surcharges do not qualify.","ffl":{"ships":true,"charge":9.99,"from":false,"excluded":false,"stated":"Select firearms can be shipped to your local SCHEELS store for a $9.99 flat rate shipping fee."},"source":{"url":"https://www.scheels.com/policies/shipping-policy","stated":"Standard (orders $75 or more)... Free; Standard (orders under $75)... $9.99","retrieved":"2026-10-02"}}},"sportsmans":{"label":"Sportsman's Warehouse","url":"https://www.sportsmans.com","kind":"retailer","shipping":{"free_over":75,"flat":9.99,"from":false,"excludes":"Excludes orders containing hazardous materials, oversize, and extra oversize items; LTL shipments are not eligible; some promotion exclusions apply.","ffl":{"ships":true,"charge":15,"from":false,"excluded":false,"stated":"All firearms will be shipped to the store you selected at no additional cost. Firearm shipments to listed Independent Partner FFL's incur a $15.00 FFL processing fee."},"source":{"url":"https://www.sportsmans.com/shipping","stated":"Orders over $75 qualify for Free Standard Shipping. Standard Ground (3-7 business days): orders $0-$75 $9.99, $75.01+ free.","retrieved":"2026-10-02"},"note":"The $15 is for an independent dealer; to one of its own stores a firearm ships at no cost. A support article says free shipping over $49; the shipping page's table is taken."}},"trex-arms":{"label":"T.REX ARMS","url":"https://www.trex-arms.com","kind":"retailer","shipping":{"free_over":null,"flat":8,"from":false,"source":{"url":"https://www.trex-arms.com/help-center/shipping-rates-policies-lead-times-142","stated":"We charge a flat rate of $8.00 for most orders shipped domestically.","retrieved":"2026-10-02"},"note":"No free-shipping threshold. Body armour, night vision and dropshipped targets ship at other flat rates."}},"right-to-bear":{"label":"Right To Bear","url":"https://www.righttobear.com","kind":"retailer","shipping":{"free_over":null,"flat":null,"from":false,"ffl":{"ships":true,"charge":null,"from":false,"excluded":false,"stated":"All firearms are shipped to a Federal Firearms Licensed dealer (FFL) on your behalf. The applicable FFL may charge you an additional transfer fee for their services. FFL items may ship separately from the rest of your order."},"source":{"url":"https://www.righttobear.com/free-shipping-on-ar-15-parts-accessories/","stated":"simply add one of these products to your cart, and the entire order ships free. FREE SHIPPING APPLIES TO ENTIRE CART WHEN THESE PRODUCTS ARE ADDED","retrieved":"2026-10-02"},"note":"Free shipping is by product (a marked set), not by a threshold, and the rate otherwise isn't stated: nothing the purchase can apply; a cart with one of those products ships free."}},"redcon1":{"label":"Redcon1 Tactical","url":"https://redcon1tactical.com","kind":"retailer","shipping":{"free_over":200,"flat":9.95,"from":false,"ffl":{"ships":true,"charge":null,"from":false,"excluded":false,"stated":"All firearms purchases must ship to a Federal Firearms License (FFL) Dealer. A direct Adult Signature will be required for all items with serial numbers requiring an FFL transfer."},"source":{"url":"https://redcon1tactical.com/shipping-policy.html","stated":"Free shipping over $200 & Fast Same-Day Shipping on all orders placed before 1 p.m. EST M-F / 11 a.m. SAT. We offer flat-rate shipping of $9.95 regardless of the weight, size, or location using USPS and UPS","retrieved":"2026-10-02"}}},"impact-guns":{"label":"Impact Guns","url":"https://www.impactguns.com","kind":"retailer","shipping":{"free_over":null,"flat":null,"from":false,"ffl":{"ships":true,"charge":null,"from":false,"excluded":false,"stated":"All firearms ship to a licensed FFL dealer near you. Free shipping covers our cost to ship to the FFL; the FFL's transfer fee is paid directly to them and varies by dealer."},"source":{"url":"https://www.impactguns.com/free-shipping/","stated":"Free standard shipping applies to many firearms—particularly higher-value items—and some accessories. Lower-cost accessories and small parts may not qualify.","retrieved":"2026-10-02"},"note":"Free shipping is by product, shown on its page; no threshold and no rate otherwise: nothing the purchase can apply."}},"mas-defense":{"label":"MAS Defense","url":"https://www.masdefense.com","kind":"manufacturer","shipping":null,"note":"The maker's own shop. Its shipping page (https://www.masdefense.com/articles.php?ID=57, read 2026-10-28 by batch 15's owner) gives lead times and where it won't ship, no rate or threshold. Added for its NERO handguards, which no other seller on file carries (catalog batch 15)."},"mile-high":{"label":"Mile High Shooting Accessories","url":"https://www.milehighshooting.com","kind":"retailer","shipping":{"free_over":250,"flat":null,"from":false,"excludes":"Select products, excludes ammo, barrels, dummy rounds, reloading supplies, RRS, suppressors, handguns, items already on sale, other restrictions may apply, discounts cannot be combined. (the FAQ, https://www.milehighshooting.com/faq/)","ffl":{"ships":true,"charge":null,"from":false,"excluded":true,"stated":"Mile High Shooting Accessories (MHSA) will only ship suppressors to Class III FFL holders. (the FAQ keeps suppressors and handguns out of the free shipping)"},"source":{"url":"https://www.milehighshooting.com/shipping-returns/","stated":"Free ground shipping on orders over $250! (the home page's banner; the policy page lists the service levels without prices)","retrieved":"2026-10-02"},"note":"The rate under $250 isn't published. A suppressor is excluded from the free shipping."}},"silencer-shop":{"label":"Silencer Shop","url":"https://www.silencershop.com","kind":"retailer","shipping":{"free_over":null,"flat":null,"from":false,"ffl":{"ships":true,"charge":null,"from":false,"excluded":false,"stated":"We will arrange for shipment of the products to you (except for NFA Items and GCA Firearms, which will be transferred and delivered to your selected dealer). Never pay a transfer fee when you order at silencershop.com."},"source":{"url":"https://www.silencershop.com/terms-and-conditions-for-sales-and-services","stated":"You will pay all shipping and handling charges specified during the ordering process.","retrieved":"2026-10-02"},"note":"No rate or threshold on the page."}},"kygunco":{"label":"KYGUNCO","url":"https://www.kygunco.com","kind":"retailer","shipping":{"free_over":null,"flat":13.94,"from":false,"ffl":{"ships":true,"charge":0,"from":false,"excluded":false,"stated":"Most firearms are shipped free unless otherwise noted. All firearms must be shipped to a Federal Firearms License (FFL) dealer in your area."},"source":{"url":"https://www.kygunco.com/page/shipping-policy","stated":"We offer a flat-rate shipping fee of $13.94 / 25 lbs for all other orders.","retrieved":"2026-10-02"},"note":"The flat rate is per 25 lb; a build's parts are under that. Hawaii, Alaska and the territories add $50."}},"capitol-armory":{"label":"Capitol Armory","url":"https://www.capitolarmory.com","kind":"retailer","shipping":{"free_over":null,"flat":5.95,"from":false,"ffl":{"ships":true,"charge":29.95,"from":false,"excluded":false,"stated":"Suppressors ship for a flat rate of $29.95 and ship via UPS. Yes, in the 42 states where suppressors are legal we ship directly to your residence via UPS Ground with adult signature."},"source":{"url":"https://www.capitolarmory.com/support/shipping_returns_policy.html","stated":"All accessories ship for a flat rate of $5.95, regardless of the amount purchased.","retrieved":"2026-10-02"},"note":"The dealer-only charge on file is the suppressor's (the only dealer-only part it sells here); the page states none for a receiver."}},"alexanders":{"label":"Alexander's Store","url":"https://alexandersstore.com","kind":"retailer","shipping":{"free_over":null,"flat":null,"from":false,"ffl":{"ships":true,"charge":null,"from":false,"excluded":false,"stated":"All firearms must be shipped to an FFL dealer."},"source":{"url":"https://alexandersstore.com/terms-conditions/","stated":"Most orders are processed and shipped within 2 business days. Delivery times will depend on your location, but in most cases, packages arrive within 3 to 7 business days.","retrieved":"2026-10-02"},"note":"No rate or threshold on the page."}},"dirty-bird":{"label":"Dirty Bird Industries","url":"https://dirtybirdusa.com","kind":"retailer","shipping":{"free_over":null,"flat":null,"from":false,"ffl":{"ships":true,"charge":null,"from":false,"excluded":false,"stated":"FFL (Federal Firearms License): Required for all firearm shipments, receivers, and any serialized components. You agree to their transfer fees."},"source":{"url":"https://dirtybirdusa.com/shipping-policy/","stated":"Orders under 40 lbs qualify for free FedEx 2-Day shipping; Orders over 40 lbs and $50+ qualify for free standard shipping. Exclusions: ammunition, hazmat, CO2 cartridges, rifle bags/cases.","retrieved":"2026-10-02"},"note":"The page's free shipping turns on weight, value, dimensions and item type together, and states no rate otherwise: nothing the purchase can apply as a threshold."}},"gritr":{"label":"GRITR Outdoors","url":"https://gritroutdoors.com","kind":"retailer","shipping":{"free_over":0,"flat":null,"from":false,"source":{"url":"https://gritroutdoors.com/shipping-delivery/","stated":"Free shipping is available to all 50 US states and D.C. US Standard Ground is guaranteed to arrive within 7-10 business days from the time of order","retrieved":"2026-10-02"},"note":"No minimum is stated on the page (a search snippet says none; not used). Its other shipping page is an untouched platform template about weight-based rates."}},"gritr-sports":{"label":"GRITR Sports","url":"https://gritrsports.com","kind":"retailer","shipping":null,"note":"https://gritrsports.com/us-shipping/ (2026-10-06) states no rate or threshold: \"Selected items on our website are eligible for free ground shipping\", \"the availability of free shipping is item-specific and will be clearly indicated on the product's page\". A shop of its own beside GRITR Outdoors: what it lists isn't at gritroutdoors.com's addresses."},"arsenal-engineering":{"label":"Arsenal Engineering","url":"https://arsenal-engineering.com","kind":"retailer","shipping":null,"note":"https://arsenal-engineering.com/delivery-policy/ (2026-10-02) states no rate or threshold; shipping is priced at checkout."},"rifle-supply":{"label":"Rifle Supply","url":"https://riflesupply.com","kind":"retailer","shipping":{"free_over":0,"flat":null,"from":false,"excludes":"All firearms and frames, All rifle upper and lowers, All online exclusives, All ammo, All rifle bags and hard cases, All complete rifle build kits, All steel targets","ffl":{"ships":true,"charge":null,"from":false,"excluded":true,"stated":"All orders that contain FFL items may take longer, because we need to get ahold of your preferred FFL's information. Frames (Serialized, Rates subjected to change) - $19.50 each; the rate for rifle uppers and lowers, excluded from free shipping, isn't given."},"source":{"url":"https://riflesupply.com/shipping-returns/","stated":"Due to high shipping prices, we have a few standard exclusions from our 'FREE SHIPPING SITEWIDE*' deal.","retrieved":"2026-10-02"},"note":"Free sitewide for what isn't excluded; a receiver (excluded) ships at a rate the page doesn't give."}},"aerospace-arms":{"label":"Aerospace Arms","url":"https://aerospacearms.com","kind":"retailer","shipping":null,"note":"https://aerospacearms.com/shipping-returns/ (2026-10-02): \"most items will be charged a flat rate for shipping or qualify for free shipping depending on the order total\", no amounts; the home page's footer says free over $300 and its meta description over $150, and a banner says stripped uppers and lowers ship free. The contradiction is left unresolved rather than picked from."},"alquist":{"label":"Alquist Arms","url":"https://www.alquistarms.com","kind":"retailer","shipping":{"free_over":null,"flat":null,"from":false,"ffl":{"ships":true,"charge":25,"from":false,"excluded":false,"stated":"Firearms- $25.00 Flat Fee Per Firearm"},"source":{"url":"https://www.alquistarms.com/policies/","stated":"Firearms- $25.00 Flat Fee Per Firearm (shipping); A 10% inconvenience fee will be charged for ***ANY*** web store order that is requested to be refunded.","retrieved":"2026-10-02"},"note":"No rate or threshold for other items on the page. A California dealer: ships only to the address on the buyer's licence, adult signature."}},"ar15discounts":{"label":"AR15Discounts","url":"https://ar15discounts.com","kind":"retailer","shipping":{"free_over":null,"flat":null,"from":false,"ffl":{"ships":true,"charge":null,"from":false,"excluded":false,"stated":"All regulated items will ship with mandatory adult signature to the FFL. We must have the receiving businesses FFL/SOT/CFD on file before the order can be processed and shipped."},"source":{"url":"https://ar15discounts.com/shipping-policy/","stated":"(the page covers delivery timeframes and carrier options; no dollar rates)","retrieved":"2026-10-02"},"note":"No rate or threshold on the page."}},"bear-creek":{"label":"Bear Creek Arsenal","url":"https://www.bearcreekarsenal.com","kind":"retailer","shipping":{"free_over":null,"flat":null,"from":false,"ffl":{"ships":true,"charge":null,"from":false,"excluded":false,"stated":"ALL complete firearms, 100% lowers and lower assemblies must be shipped to an FFL Dealer. (https://www.bearcreekarsenal.com/shipping/)"},"source":{"url":"https://www.bearcreekarsenal.com/free-shipping","stated":"Free Ground Shipping with Fedex: Available on all orders with Rifle Barrels, AR Pistol Barrels and BCGs. Does not include Complete Uppers. To check shipping costs, add the product to your cart and go to the cart page.","retrieved":"2026-10-02"},"note":"Free shipping is by product (barrels, bolt carrier groups), not by a threshold, and the rate otherwise is shown only in the cart: nothing the purchase can apply."}},"cloud-defensive":{"label":"Cloud Defensive","url":"https://clouddefensive.com","kind":"manufacturer"},"b5-systems":{"label":"B5 Systems","url":"https://b5systems.com","kind":"manufacturer"},"cmmg":{"label":"CMMG","url":"https://cmmg.com","kind":"manufacturer"},"cheaper-than-dirt":{"label":"Cheaper Than Dirt","url":"https://www.cheaperthandirt.com","kind":"retailer"},"tactical-transition":{"label":"Tactical Transition","url":"https://tacticaltransition.com","kind":"retailer"},"abc-sportz":{"label":"ABC Sportz","url":"https://abcsportz.com","kind":"retailer"},"the-country-shed":{"label":"The Country Shed","url":"https://www.thecountryshed.com","kind":"retailer"},"charlies-custom-clones":{"label":"Charlie's Custom Clones","url":"https://charliescustomclones.com","kind":"retailer","shipping":{"free_over":149,"flat":null,"from":false,"ffl":{"ships":true,"charge":null,"from":false,"excluded":false,"stated":"Shipment of registered items (firearms and serialized receivers) ship only to federal firearms licensees."},"source":{"url":"https://charliescustomclones.com/pages.php?pageid=2","stated":"We offer free domestic shipping on orders over $149.00","retrieved":"2026-11-03"},"note":"\"over $149.00\": taken as the threshold. The rate under it isn't published (\"Shipping - Timing, International, Restrictions\" names none); free shipping \"is quoted as 5-7 days\". Rifles, shotguns and ammunition in an order take away any shipping discount. Read through a page reader on 2026-11-03 for Geissele's gray buffer tube assembly."}}},"offers":{"a2-flash-hider":[{"vendor":"bcm","url":"https://bravocompanyusa.com/flash-hider-a2/","price":8,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"BCM's A2: the part is the mil-spec pattern, which many makers sell."},{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/ar15-a2-flash-hider","price":10,"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Aero Precision's A2."},{"vendor":"faxon","url":"https://faxonfirearms.com/5-56-a2-flash-hider-1-2-28-threaded/","price":9.99,"sku":"FFMD556A2","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Faxon's A2."},{"vendor":"kak","url":"https://kakindustry.com/a2-birdcage-flash-hider","price":7,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"KAK Industry's A2."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/kak-industry-a2-flash-hider-1-2x28","price":6.3,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"KAK Industry's A2 at Primary Arms."}],"aero-556-16-mid-barrel":[{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/556-16-mid-cmv-barrel","price":185,"in_stock":null,"observed":"2026-11-21","via":"harvest"}],"aero-556-bcg":[{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/ar15-556-bolt-carrier-group-complete-black-nitride","price":170,"in_stock":null,"observed":"2026-11-21","via":"harvest"}],"aero-750-gas-block":[{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/750-low-profile-gas-block-w-aero-logo-nitride","price":40,"in_stock":null,"observed":"2026-11-21","via":"harvest"}],"aero-ar15-front-sight-post-kit":[{"vendor":"kygunco","url":"https://www.kygunco.com/product/aero-precision-aprh100526c-front-sight-post-kit-detent-spring-sight","price":11.99,"sku":"229084","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/aero-precision-ar15-front-sight-post-kit/","price":8.99,"sku":"2633","in_stock":false,"observed":"2026-11-21","via":"harvest"}],"aero-carbine-gas-tube":[{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/gas-tube-carbine-length-stainless-steel","price":19,"options":{"tube":"stainless"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (SKU: APRH100017C in its text); the markup names no number."},{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/gas-tube-carbine-length-melonite","price":20,"options":{"tube":"melonite"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (SKU: APRH100281C in its text); the markup names no number."},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/1026894280?pid=924189","price":16.99,"options":{"tube":"stainless"},"sku":"924189","in_stock":false,"observed":"2026-10-30","via":"harvest","note":"MidwayUSA's own number in the markup; its page's data ties it to APRH100017C (UPC 815421020601)."},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/1025560285?pid=116459","price":17.99,"options":{"tube":"melonite"},"sku":"116459","in_stock":false,"observed":"2026-10-30","via":"harvest","note":"MidwayUSA's own number in the markup; its page's data ties it to APRH100281C (UPC 815421021394)."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/aprh100017c","price":16.99,"options":{"tube":"stainless"},"sku":"APRH100017C","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"right-to-bear","url":"https://www.righttobear.com/aero-precision-stainless-steel-gas-tubes-carbine-aprh100017c/","price":19,"options":{"tube":"stainless"},"sku":"APRH100017C","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/aero-precision-stainless-carbine-length-gas-tube/","price":12.95,"options":{"tube":"stainless"},"sku":"33279","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"AR15Discounts' own number in the markup, which carries APRH100017C as the maker's."}],"aero-charging-handle":[{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/ar15-charging-handle","price":24,"in_stock":null,"observed":"2026-11-21","via":"harvest"}],"aero-enhanced-15-handguard":[{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/ar15-15inch-mlok-handguard-bar-nut-gen2-1","price":220,"options":{"body":"black"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"APRA100218A, with the BAR barrel nut (the default way of mounting): Aero's page for this one number (in the page's SKU line); the markup names no number"},{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/ar15-15inch-m-lok-handguard-gen2","price":180,"options":{"body":"black"},"fitment":"enhanced","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"APRA100218C, the handguard alone (for the M4E1 Enhanced upper): Aero's page for this one number; the markup names no number"},{"vendor":"right-to-bear","url":"https://www.righttobear.com/aero-precision-ar-15-enhanced-mlok-rail-gen2-blk-apra100218as/","price":189.99,"options":{"body":"black"},"sku":"APRA100218AS","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"the seller's code for the one with the BAR barrel nut (its heading: \"Anodized Black (w/ BAR Barrel Nut)\")"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/aero-precision-enhanced-m-lok-ar-15-handguard-gen-2-black-15/","price":129.95,"options":{"body":"black"},"fitment":"enhanced","sku":"30256","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"the seller's own number; its mpn is APRA100218C, the handguard alone (\"requires either a BAR System Barrel Nut (sold separately) or the M4E1 Enhanced Upper Receiver\")"},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/aero-precision-enhanced-m-lok-ar-15-handguard-gen-2-black-15/","price":129.95,"options":{"body":"black"},"fitment":"enhanced","sku":"30256","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"the seller's own number; its mpn is APRA100218C, the handguard alone"},{"vendor":"kygunco","url":"https://kygunco.com/product/aero-precision-llc-apra100218c-ar15-enhanced-m-lok-15-handguard-gen-2-blk","price":140.99,"options":{"body":"black"},"fitment":"enhanced","sku":"161842","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"the seller's own number; its mpn is APRA100218C, the handguard alone"},{"vendor":"aerospace-arms","url":"https://aerospacearms.com/aero-precision-15-ar15-enhanced-m-lok-handguards-gen-2-anodized-black/","price":159.99,"options":{"body":"black"},"fitment":"enhanced","sku":"APRA100218C","in_stock":false,"observed":"2026-11-19","via":"harvest"}],"aero-m4e1-complete-upper-16-mid-r-one-15":[{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/m4e1-threaded-complete-upper-16-5-56-mid-barrel-atlas-r-one-15-m-lok-hg-anodized","price":655,"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"APAR700705M7 (the page's SKU; the markup names none)"},{"vendor":"kygunco","url":"https://www.kygunco.com/product/aero-precision-apar700705m7-m4e1-threaded-complete-upper-16in-556-mid-length-barrel-15in-m-lok-atlas-r-one-handguard-anodized-black","price":543.99,"sku":"205748","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"MPN APAR700705M7; its page repeats Aero's Includes list"},{"vendor":"rifle-supply","url":"https://riflesupply.com/Aero-Precision-M4E1-16-556-Mid-Length-Complete-Upper-Receiver-w-ATLAS-R-ONE-Handguard-16-Handguard-556-Black-APAR700705M7_p_6988.html","price":646.99,"sku":"6988","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"MPN APAR700705M7. Its own copy says carbine length, against Aero's mid-length: the price only is taken"},{"vendor":"right-to-bear","url":"https://www.righttobear.com/aero-precision-m4e1-barreled-upper-16-5-56-apar700705m7/","price":509.99,"sku":"APAR700705M7","in_stock":false,"observed":"2026-10-19","via":"harvest","note":"Its own copy says carbine length, against Aero's mid-length: the price only is taken"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/aero-precision-m4e1-threaded-complete-upper-16-5-56-mid-length-barrel-atlas-r-one-15-m-lok-hg/","price":559.99,"sku":"3611","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"MPN APAR700705M7 in its Additional Info"}],"aero-m4e1-enhanced-upper":[{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/ar15-m4e1-enhanced-upper-receiver-stripped","price":194.99,"options":{"receiver":"black"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"APAR600201C: Aero's page for this one number (in the page's SKU line); the markup names no number"},{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/ar15-m4e1-enhanced-upper-receiver-stripped-fde","price":214.99,"options":{"receiver":"fde"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"APAR600202C, FDE Cerakote: Aero's page for this one number; the markup names no number"}],"aero-m4e1-lower":[{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/m4e1-complete-lower-a2-grip-m4-stock-black","price":350,"options":{"receiver":"black"},"sku":"APAR600101","in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/m4e1-complete-lower-a2-grip-m4-stock-fde","price":370,"options":{"receiver":"fde"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Aero's page for this one finish (its number is in the page's SKU line); the markup names no number"}],"aero-m4e1-stripped-lower":[{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/m4e1-stripped-lower-receiver-anodized-black","price":155,"options":{"receiver":"black"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Aero's page for this one finish (its number is in the page's SKU line); the markup names no number"},{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/m4e1-stripped-lower-receiver-fde","price":175,"options":{"receiver":"fde"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Aero's page for this one finish (its number is in the page's SKU line); the markup names no number"},{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/m4e1-stripped-lower-receiver-od-green-anodized","price":155,"options":{"receiver":"odg"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Aero's page for this one finish (its number is in the page's SKU line); the markup names no number"},{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/m4e1-stripped-lower-receiver-od-green-cerakote","price":175,"options":{"receiver":"odg_cerakote"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Aero's page for this one finish (its number is in the page's SKU line); the markup names no number"},{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/m4e1-stripped-lower-receiver-kodiak-brown-anodized","price":155,"options":{"receiver":"kodiak"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Aero's page for this one finish (its number is in the page's SKU line); the markup names no number"},{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/m4e1-stripped-lower-receiver-sniper-grey-cerakote","price":175,"options":{"receiver":"sniper_grey"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Aero's page for this one finish (its number is in the page's SKU line); the markup names no number"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/apar600001c","price":139.99,"options":{"receiver":"black"},"sku":"APAR600001C","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"sportsmans","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/gun-parts-accessories/gun-parts-magazines/rifle-parts/receivers-lowers/aero-precision-m4e1-anodized-black-stripped-lower-receiver/p/1628378","price":139.99,"options":{"receiver":"black"},"sku":"1628378","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/aero-precision-m4e1-stripped-lower-receiver-2/","price":139.99,"options":{"receiver":"black"},"sku":"2472","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/aero-precision-m4e1-stripped-lower-receiver-2/","price":159.99,"options":{"receiver":"fde"},"sku":"3756","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/aero-precision-m4e1-stripped-lower-receiver-2/","price":139.99,"options":{"receiver":"odg"},"sku":"16645","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/aero-precision-m4e1-stripped-lower-receiver-2/","price":139.99,"options":{"receiver":"kodiak"},"sku":"16643","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/aero-precision-m4e1-stripped-lower-receiver-anodized-black/","price":139.99,"options":{"receiver":"black"},"sku":"2472","in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/aero-precision-m4e1-stripped-lower-receiver-anodized-black/","price":149.99,"options":{"receiver":"fde"},"sku":"3756","in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/aero-precision-m4e1-stripped-lower-receiver-anodized-black/","price":129.99,"options":{"receiver":"odg"},"sku":"16645","in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/aero-precision-m4e1-stripped-lower-receiver-anodized-black/","price":129.99,"options":{"receiver":"kodiak"},"sku":"16643","in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"right-to-bear","url":"https://www.righttobear.com/aero-precision-m4e1-stripped-lower-receiver-apar600001c/","price":154.99,"options":{"receiver":"black"},"sku":"APAR600001C","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"gritr-sports","url":"https://gritrsports.com/aero-precision-enhanced-lower-receiver-apar600001c","price":112.99,"options":{"receiver":"black"},"sku":"AERP-APAR600001C","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"rifle-supply","url":"https://riflesupply.com/Aero-Precision-M4E1-Stripped-AR-Lower-Receiver-Multi-Cal-APAR600001C_p_3498.html","price":164.99,"options":{"receiver":"black"},"sku":"3498","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"aerospace-arms","url":"https://aerospacearms.com/aero-precision-m4e1-stripped-lower-receiver-anodized-black-free-shipping/","price":139.99,"options":{"receiver":"black"},"sku":"APAR600001C","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"alquist","url":"https://www.alquistarms.com/aero-precision-apar600001c-m4e1-receiver-multi-caliber-black-anodized-finish-7075-t6-aluminum-material-with-mil-spec-dimensions-for-ar-15/","price":139.99,"options":{"receiver":"black"},"sku":"APAR600001C","in_stock":false,"observed":"2026-11-21","via":"harvest"}],"aero-m4e1-threaded-upper":[{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/m4e1-threaded-stripped-upper-receiver-anodized-black","price":150,"options":{"receiver":"black"},"in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/m4e1-threaded-assembled-upper-receiver-black","price":175,"options":{"receiver":"black"},"fitment":"assembled","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"APAR700201AC: the assembled receiver (port door and forward assist installed)"},{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/m4e1-threaded-stripped-upper-receiver-fde","price":170,"options":{"receiver":"fde"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Aero's page for this one finish (its number is in the page's SKU line); the markup names no number"},{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/m4e1-stripped-threaded-upper-odg-ano","price":150,"options":{"receiver":"odg"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Aero's page for this one finish (its number is in the page's SKU line); the markup names no number"},{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/m4e1-threaded-stripped-upper-receiver-kodiak-brown-ano","price":150,"options":{"receiver":"kodiak"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Aero's page for this one finish (its number is in the page's SKU line); the markup names no number"},{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/m4e1-threaded-assembled-upper-sniper-grey-cerakote","price":195,"options":{"receiver":"sniper_grey"},"fitment":"assembled","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"APAR700272AC: the assembled receiver, the one way Aero sells it in Sniper Grey; the markup names no number"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/aero-precision-m4e1-threaded-assembled-upper-receiver-sniper-grey-cerakote","price":174.99,"options":{"receiver":"sniper_grey"},"fitment":"assembled","sku":"14594","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/aero-precision-m4e1-threaded-assembled-upper-receiver-sniper-grey-cerakote/","price":174.99,"options":{"receiver":"sniper_grey"},"fitment":"assembled","sku":"14594","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Its markup's MPN: APAR700272AC"}],"aero-mid-gas-tube":[{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/gas-tube-mid-length-stainless-steel","price":20,"in_stock":null,"observed":"2026-11-21","via":"harvest"}],"aero-r-one-10-3-handguard":[{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/ar15-10-3-atlas-r-one-m-lok-handguard-anodized-black","price":205,"options":{"body":"black"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Aero's page for this one finish (its number is in the page's SKU line); the markup names no number"},{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/ar15-10-3-atlas-r-one-m-lok-handguard-sniper-grey-cerakote","price":225,"options":{"body":"sniper_grey"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Aero's page for this one finish (its number is in the page's SKU line); the markup names no number"},{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/ar15-10-3-atlas-r-one-m-lok-handguard-kodiak-brown-anodized","price":205,"options":{"body":"kodiak"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Aero's page for this one finish (its number is in the page's SKU line); the markup names no number"},{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/ar15-10-3-atlas-r-one-m-lok-handguard-od-green-anodized","price":205,"options":{"body":"odg"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Aero's page for this one finish (its number is in the page's SKU line); the markup names no number"},{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/ar15-10-3-atlas-r-one-m-lok-handguard-od-green-cerakote","price":225,"options":{"body":"odg_cerakote"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Aero's page for this one finish (its number is in the page's SKU line); the markup names no number"},{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/ar15-10-3-atlas-r-one-m-lok-handguard-burnt-bronze-cerakote","price":225,"options":{"body":"burnt_bronze"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Aero's page for this one finish (its number is in the page's SKU line); the markup names no number"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/aero-precision-atlas-r-one-m-lok-hg-10-3in-black","price":184.99,"options":{"body":"black"},"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Primary Arms' page for the black 10.3 in (its markup names no number)."}],"aero-r-one-12-7-handguard":[{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/ar15-12-7-atlas-r-one-m-lok-handguard-kodiak-brown-anodized","price":215,"options":{"body":"kodiak"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Aero's page for this one finish (its number is in the page's SKU line); the markup names no number"},{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/ar15-12-7-atlas-r-one-m-lok-handguard-od-green-anodized","price":215,"options":{"body":"odg"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Aero's page for this one finish (its number is in the page's SKU line); the markup names no number"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/aero-precision-atlas-r-one-m-lok-ar-15-handguard-odg-anodized-12-7in","price":194.99,"options":{"body":"odg"},"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Primary Arms' page for the OD Green Anodized 12.7 in (its markup names no number)."}],"aero-r-one-15-handguard":[{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/ar15-15-atlas-r-one-m-lok-handguard-anodized-black","price":225,"options":{"body":"black"},"in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/ar15-15-atlas-r-one-m-lok-handguard-od-green-anodized","price":225,"options":{"body":"odg"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Aero's page for this one finish (its number is in the page's SKU line); the markup names no number"},{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/ar15-15-atlas-r-one-m-lok-handguard-kodiak-brown-anodized","price":225,"options":{"body":"kodiak"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Aero's page for this one finish (its number is in the page's SKU line); the markup names no number"},{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/ar15-15-atlas-r-one-m-lok-handguard-od-green-cerakote","price":245,"options":{"body":"odg_cerakote"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Aero's page for this one finish (its number is in the page's SKU line); the markup names no number"},{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/r-one-m-lok-15-in-handguard-socom-blue","price":122.5,"options":{"body":"socom_blue"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Aero's page for this one finish (its number is in the page's SKU line); the markup names no number"}],"aero-r-one-16-6-handguard":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/aero-precision-atlas-r-one-m-lok-ar-15-handguard-16-6in","price":209.99,"options":{"body":"black"},"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Primary Arms' page for the 16.6 in, the black one by its pictures (its markup names no number)."}],"aero-r-one-7-3-handguard":[{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/ar15-7-atlas-r-one-m-lok-handguard-anodized-black","price":185,"options":{"body":"black"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Aero's page for this one finish (its number is in the page's SKU line); the markup names no number"},{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/ar15-7-3-atlas-r-one-m-lok-handguard-sniper-grey-cerakote","price":205,"options":{"body":"sniper_grey"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Aero's page for this one finish (its number is in the page's SKU line); the markup names no number"},{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/ar15-7-3-atlas-r-one-m-lok-handguard-kodiak-brown-anodized","price":185,"options":{"body":"kodiak"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Aero's page for this one finish (its number is in the page's SKU line); the markup names no number"},{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/ar15-7-3-atlas-r-one-m-lok-handguard-od-green-anodized","price":185,"options":{"body":"odg"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Aero's page for this one finish (its number is in the page's SKU line); the markup names no number"},{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/ar15-7-3-atlas-r-one-m-lok-handguard-od-green-cerakote","price":205,"options":{"body":"odg_cerakote"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Aero's page for this one finish (its number is in the page's SKU line); the markup names no number"}],"aero-r-one-9-3-handguard":[{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/ar15-9-atlas-r-one-m-lok-handguard-anodized-black","price":195,"options":{"body":"black"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Aero's page for this one finish (its number is in the page's SKU line); the markup names no number"},{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/ar15-9-3-atlas-r-one-m-lok-handguard-kodiak-brown-anodized","price":195,"options":{"body":"kodiak"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Aero's page for this one finish (its number is in the page's SKU line); the markup names no number"}],"aero-s-one-15-handguard":[{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/ar15-15-atlas-s-one-m-lok-handguard-anodized-black","price":225,"options":{"body":"black"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Aero's page for this one finish (its number is in the page's SKU line); the markup names no number"},{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/ar15-15-atlas-s-one-m-lok-handguard-od-green-anodized","price":225,"options":{"body":"odg"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Aero's page for this one finish (its number is in the page's SKU line); the markup names no number"},{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/ar15-15-atlas-s-one-m-lok-handguard-kodiak-brown-anodized","price":225,"options":{"body":"kodiak"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Aero's page for this one finish (its number is in the page's SKU line); the markup names no number"},{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/ar15-15-atlas-s-one-m-lok-handguard-sniper-grey-cerakote","price":245,"options":{"body":"sniper_grey"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Aero's page for this one finish (its number is in the page's SKU line); the markup names no number"},{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/ar15-15-atlas-s-one-m-lok-handguard-od-green-cerakote","price":245,"options":{"body":"odg_cerakote"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Aero's page for this one finish (its number is in the page's SKU line); the markup names no number"},{"vendor":"kygunco","url":"https://www.kygunco.com/product/aero-precision-apra500105a-ar15-15-atlas-s-one-m-lok-handguard-ano","price":175.99,"options":{"body":"black"},"sku":"228799","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"KYGUNCO's item number; the markup's mpn is APRA500105A"},{"vendor":"sportsmans","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/gun-parts-accessories/gun-parts-magazines/rifle-parts/rails-handguards/aero-precision-ar15-15in-atlas-s-one-m-lok-handguard-black/p/1627563","price":204.99,"options":{"body":"black"},"sku":"1627563","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Sportsman's Warehouse's item number; the markup's mpn is APRA500105A"}],"aimpoint-duty-rds-kit":[{"vendor":"mile-high","url":"https://www.milehighshooting.com/aimpoint-duty-rds-red-dot/","price":514,"sku":"200759","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"kygunco","url":"https://www.kygunco.com/product/aimpoint-200759-duty-red-dot-sight-onepiece-torsion-nut-mount-39mm","price":514,"sku":"218180","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"KYGunCo's own item number (its markup: sku 218180, mpn 200759; the page: \"Item # 218180 Style MPN-200759 UPC 7350004386963\")."},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/1024757827","price":514,"sku":"572941","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"A family page with two offers: 572941 is this configuration (mpn 7350004386963, the UPC Bravo Company and KYGunCo give for 200759: \"2 MOA Dot with 39mm Picatinny Mount and Spacer\"); 592322 is the multi-reticle sight, another product."},{"vendor":"bcm","url":"https://bravocompanyusa.com/aimpoint-duty-rds-red-dot-sight-one-piece-torsion-nut-mount-39mm/","price":514,"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"A page of this one product whose Offer markup names no number (its page data says sku AIMPOINT-200759, mpn 200759)."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/aimpoint-duty-rds-2-moa-red-dot-sight","price":514,"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (\"SKU: 200759 MPN: 200759\" in its text) whose markup carries the same Offer twice, at one price, and names no number."},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/aimpoint-duty-rds-red-dot-sight-646938","price":514,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (its in-the-box list: \"1x Torsion nut mount and spacer (39mm)\") whose markup names no number."}],"aimpoint-micro-t-2-kit":[{"vendor":"mile-high","url":"https://www.milehighshooting.com/aimpoint-200198-micro-t-2-2moa-lrp/","price":1108,"sku":"200198","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"the page's SKU line says 200198 and its markup carries one Offer in US dollars; its spec table is the standard listing's (Article Number 200170), which doesn't change what is sold"},{"vendor":"bcm","url":"https://bravocompanyusa.com/micro-t-2-2-moa-red-dot-reflex-sight-with-39-mm-spacer-lrp-mount/","price":1108,"sku":"AIMPOINT-200198","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Bravo Company's own number (its page data: sku AIMPOINT-200198, mpn 200198)."}],"aimpoint-pro":[{"vendor":"mile-high","url":"https://www.milehighshooting.com/aimpoint-12841-patrol-rifle-optic/","price":512,"sku":"12841","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"its markup carries one Offer in US dollars with sku 12841 (json-ld); its spec table has another sight's rows, which doesn't change what is sold"},{"vendor":"sportsmans","url":"https://www.sportsmans.com/hunting-gear-supplies/optics-binoculars-scopes-rangefinders/red-dots/aimpoint-patrol-rifle-optic-1x-red-dot-2-moa-dot/p/1379668","price":512,"sku":"1379668","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Sportsman's own number (json-ld sku 1379668, mpn 12841)."},{"vendor":"bcm","url":"https://bravocompanyusa.com/aimpoint-pro-patrol-rifle-optic/","price":512,"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"a page of one product whose markup (microdata) names no number; the page's SKU line says AIMPOINT-12841"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/aimpoint-pro-patrol-rifle-optic-with-mount","price":512,"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"a page of one product whose markup (microdata, two offers at one price) names no number; the page's SKU line says 12841"},{"vendor":"impact-guns","url":"https://www.impactguns.com/sights/aimpoint-pro-patrol-rifle-optic-30mm-modular-qrp2-ar-15-mount-flip-covers-7350004383399-12841","price":512.49,"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"a page of one product whose markup (microdata, two offers at one price) names no number; 12841 and the UPC 7350004383399 are in its address"}],"armaspec-stealth-recoil-spring-gen4-c":[{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/102597809","price":76.49,"sku":"461128","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"MidwayUSA's one page for every version; its own number for the C in the markup (UPC 810048492688 as the mpn)."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/arm253-c","price":76.49,"sku":"ARM253-C","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Midwest Gun Works, 'Armaspec Gen 4 Stealth Recoil Spring, SRS-C 3.3oz'."},{"vendor":"redcon1","url":"https://redcon1tactical.com/armaspec-ar-15-stealth-recoil-spring-srs-carbine-gen4-c-3-3-oz.html","price":76.49,"sku":"ARM253-C","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Redcon1, the C ('Mnf#/Vendor# ARM253-C'): the number is the markup's mpn. Out of stock when read."}],"armaspec-stealth-recoil-spring-gen4-h":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/armaspec-stealth-ar-15-recoil-spring-h-3-8-oz-gen-4","price":76.49,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product ('SKU: ARM253-H MPN: ARM253-H' in its text); its offer markup names no number (make offers show, 2026-10-18)."},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/102597809","price":76.49,"sku":"875246","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"MidwayUSA's one page for every version; its own number for the H in the markup (UPC 810048492695 as the mpn)."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/arm253-h","price":76.49,"sku":"ARM253-H","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Midwest Gun Works, 'Armaspec Gen 4 Stealth Recoil Spring, SRS-H 3.8oz'."},{"vendor":"redcon1","url":"https://redcon1tactical.com/armaspec-ar-15-stealth-recoil-spring-srs-heavy-gen4-h-3-8-oz.html","price":76.49,"sku":"ARM253-H","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Redcon1, the H: the number is the markup's mpn. Out of stock when read."}],"armaspec-stealth-recoil-spring-gen4-h2":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/armaspec-stealth-ar-15-recoil-spring-h2-4-7-oz-gen-4","price":76.49,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product ('SKU: ARM253-H2 MPN: ARM253-H2' in its text); its offer markup names no number (make offers show, 2026-10-18)."},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/102597809","price":76.49,"sku":"893401","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"MidwayUSA's one page for every version; its own number for the H2 in the markup (UPC 810048492701 as the mpn)."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/arm253-h2","price":76.49,"sku":"ARM253-H2","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Midwest Gun Works, 'Armaspec Gen 4 Stealth Recoil Spring, SRS-H2 4.7oz'."}],"armaspec-stealth-recoil-spring-gen4-h3":[{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/102597809","price":76.49,"sku":"284577","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"MidwayUSA's one page for every version; its own number for the H3 in the markup (UPC 810048492787 as the mpn)."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/arm253-h3","price":76.49,"sku":"ARM253-H3","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Midwest Gun Works, 'Armaspec Gen 4 Stealth Recoil Spring, SRS-H3 5.6oz'."},{"vendor":"rifle-supply","url":"https://riflesupply.com/armaspec-stealth-recoil-spring-gen-4-lower-parts-h3-buffer-ar-15-black-arm253-h3/","price":82.99,"sku":"ARM253-H3","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Rifle Supply, 'Armaspec Stealth Recoil Spring Gen 4 | Lower Parts | H3 Buffer' (its own number 9896, mpn ARM253-H3). Out of stock when read."}],"b5-bravo-stock":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/b5-systems-sopmod-bravo-milspec-stock-flat-dark-earth","price":57.95,"options":{"body":"fde"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product in FDE (the page says SKU: BRV-202-01-FDE, MPN: BRV-1085); its offer markup names no number (the colour pass, 2026-10-06, looked at with `make offers ARGS=\"show <url>\"`)."},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/b5-systems-bravo-stock-844455","price":57.95,"options":{"body":"coyote"},"sku":"844459","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"T.REX's own number for Coyote Brown (the markup's 'B5 Systems BRAVO Stock - Coyote Brown')."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/b5-systems-bravo-stock-mil-spec-black","price":57.95,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product in black (Primary Arms' own number is BRV-201-01-BLK); its offer markup names no number (`make offers ARGS=\"show <url>\"`, 2026-10-06: the entry named that number until then, and the read refused it)."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/b5-systems-bravo-black-mil-spec-stock-oem/","price":57.95,"options":{"body":"black"},"sku":"17930","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The black one alone (MPN BRV-1082); the page's own number is 17930."},{"vendor":"wing-tactical","url":"https://www.wingtactical.com/firearm-parts-accessories/ar-15-parts/ar-stocks-and-accessories/b5-systems-bravo-stock/","price":57.95,"options":{"body":"black"},"sku":"B5-BRV","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One price (SKU B5-BRV) for the three colours the page offers (MPN: BRV-1082 / BRV-1085 / BRV-1104): the product's entry, left as it was."},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/b5-systems-bravo-stock-844455","price":57.95,"options":{"body":"black"},"sku":"844457","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"T.REX's own number for Black (Coyote Brown is 844459)."},{"vendor":"bcm","url":"https://bravocompanyusa.com/b5-systems-sopmod-bravo-milspec-stock-black/","price":58,"options":{"body":"black"},"sku":"B5-BRV-1082-BLK-BRAVO","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Bravo Company's shop (the vendor on file as bcm), the black one."}],"b5-enhanced-sopmod-stock":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/b5-systems-enhanced-sopmod-stock-mil-spec-flat-dark-earth-sop-202-01-fde","price":95,"options":{"body":"fde"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product in FDE (the page says SKU: SOP-202-01-FDE, MPN: SOP-1075); its offer markup names no number."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/b5-systems-enhanced-sopmod-stock-mil-spec-coyote-brown-sop-203-01-coy","price":95,"options":{"body":"coyote"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product in Coyote Brown (the page says SKU: SOP-203-01-COY, MPN: SOP-1076); its offer markup names no number."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/b5-systems-enhanced-sopmod-stock-mil-spec-olive-drab-green","price":95,"options":{"body":"odg"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product in OD Green (the page says SKU: SOP-1097, MPN: SOP-1097); its offer markup names no number."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/b5-systems-enhanced-sopmod-stock-mil-spec-wolf-gray","price":95,"options":{"body":"wolf"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product in Wolf Grey (the page says SKU: SOP-1123, MPN: SOP-1123); its offer markup names no number."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/sop-10xx","price":95,"options":{"body":"fde"},"sku":"SOP-1075","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One page for five colours, each under B5's number (SOP-1075 Flat Dark Earth)."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/sop-10xx","price":95,"options":{"body":"coyote"},"sku":"SOP-1076","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One page for five colours, each under B5's number (SOP-1076 Coyote Brown)."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/sop-10xx","price":95,"options":{"body":"odg"},"sku":"SOP-1097","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One page for five colours, each under B5's number (SOP-1097 OD Green)."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/sop-10xx","price":95,"options":{"body":"wolf"},"sku":"SOP-1123","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One page for five colours, each under B5's number (SOP-1123 Wolf Grey)."},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/b5-systems-enhanced-sopmod-stock-844470","price":95,"options":{"body":"coyote"},"sku":"844472","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"T.REX's own number for Coyote Brown (the markup's 'B5 Systems Enhanced SOPMOD Stock - Coyote Brown')."},{"vendor":"impact-guns","url":"https://www.impactguns.com/stocks-forends/b5-systems-enhanced-sopmod-stock-coyote-brown-for-ar-15-m4-with-mil-spec-receiver-extension-814927020023-","price":95,"options":{"body":"coyote"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product in Coyote Brown (its title; its address ends in the UPC 814927020023); its offer markup names no number."},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/b5-systems-enhanced-sopmod-stock-mil-spec-2/","price":95,"options":{"body":"fde"},"sku":"14702","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Dirty Bird's own number for 'B5 Systems Enhanced SOPMOD Stock - Mil-Spec - FDE' in the markup (one page, a number a colour; no black among its seven offers)."},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/b5-systems-enhanced-sopmod-stock-mil-spec-2/","price":95,"options":{"body":"coyote"},"sku":"14739","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Dirty Bird's own number for '... - Coyote Brown'."},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/b5-systems-enhanced-sopmod-stock-mil-spec-2/","price":95,"options":{"body":"odg"},"sku":"14703","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Dirty Bird's own number for '... - OD Green'."},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/b5-systems-enhanced-sopmod-stock-mil-spec-2/","price":95,"options":{"body":"wolf"},"sku":"14740","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Dirty Bird's own number for '... - Wolf Grey'."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/b5-systems-sopmod-ar-15-mil-spec-polymer-stock-with-quick-detach-mount-black-sop-201-01-blk","price":95,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (Primary Arms' own number SOP-201-01-BLK in its address; the page says MPN: SOP-1074); its offer markup names no number."},{"vendor":"wing-tactical","url":"https://www.wingtactical.com/firearm-parts-accessories/ar-15-parts/ar-stocks-and-accessories/b5-systems-enhanced-sopmod-stock/","price":95,"options":{"body":"black"},"sku":"B5-SOP","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One price (SKU B5-SOP) for the three colours the page offers (MPN: SOP-1074 / SOP-1075 / SOP-1097): the product's entry, left as it was."},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/b5-systems-enhanced-sopmod-stock-844470","price":95,"options":{"body":"black"},"sku":"844471","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"T.REX's own number for Black (Coyote Brown is 844472)."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/b5-systems-enhanced-sopmod-mil-spec-stock-black-oem/","price":95,"options":{"body":"black"},"sku":"18347","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The black one alone, sold as OEM (in a bag, not B5's retail package); the markup carries the seller's own number."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/sop-10xx","price":95,"options":{"body":"black"},"sku":"SOP-1074","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One page for five colours, each under B5's number (SOP-1074 Black)."},{"vendor":"sportsmans","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/gun-parts-accessories/gun-parts-magazines/rifle-parts/stocks-recoil-pads/b5-systems-enhanced-sopmod-ar15-stock-black/p/1857713","price":95.99,"options":{"body":"black"},"sku":"1857713","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"rifle-supply","url":"https://riflesupply.com/B5-Systems-SOPMOD-Stock-Mil-Spec-Quick-Detach-Mount-Black_p_5171.html","price":106.99,"options":{"body":"black"},"sku":"5172","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Titled 'SOPMOD Stock' with B5's number for the black Enhanced (SOP-1074) and its QD mount named."},{"vendor":"bcm","url":"https://bravocompanyusa.com/b5-enhanced-sopmod-milspec-stock-black/","price":95,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest"}],"b5-type-23-p-grip":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/b5-systems-p-grip-23-black","price":19,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of the black one alone (the page: SKU: B5PGR-1122, MPN: PGR-1122); its offer markup names no number (`make offers ARGS=\"show <url>\"`, 2026-10-19: 19.00 USD, sku=- mpn=-)."},{"vendor":"rifle-supply","url":"https://riflesupply.com/B5-Systems-Type-23-P-Grip-AR15-Black-PGR-1122_p_5150.html","price":23.99,"options":{"body":"black"},"sku":"5150","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The black one (the markup's 'B5 Systems Type 23 P-Grip | AR15 | Black | PGR-1122', mpn PGR-1122); out of stock when read. Its two photos are an earlier moulding by their look (no texture panel)."},{"vendor":"sportsmans","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/gun-parts-magazines/rifle-parts/rifle-grips/b5-systems-p-grip-23-rifle-grip-black/p/1857716","price":19.99,"options":{"body":"black"},"sku":"1857716","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Sportsman's own number for the black one ('B5 Systems P-Grip 23 Rifle Grip - Black', mpn PGR-1122)."},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/b5-systems-type-23-p-grip/","price":20,"options":{"body":"black"},"sku":"1008639","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"T.REX's own number for the black one ('B5 Systems Type 23 P-Grip - Black')."},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/b5-systems-type-23-p-grip/","price":20,"options":{"body":"coyote"},"sku":"1008640","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"T.REX's own number for Coyote Brown ('B5 Systems Type 23 P-Grip - Coyote Brown')."},{"vendor":"sportsmans","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/gun-parts-magazines/rifle-parts/rifle-grips/b5-systems-p-grip-23-rifle-grip-od-green/p/1890653","price":20,"options":{"body":"odg"},"sku":"1890653","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Sportsman's own number for OD Green ('B5 Systems P-Grip 23 Rifle Grip - OD Green', mpn PGR-1134)."},{"vendor":"sportsmans","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/gun-parts-magazines/rifle-parts/rifle-grips/b5-systems-p-grip-23-rifle-grip-wolf-gray/p/1857718","price":19.99,"options":{"body":"wolf"},"sku":"1857718","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Sportsman's own number for Wolf Grey ('B5 Systems P-Grip 23 Rifle Grip - Wolf Gray', mpn PGR-1118); out of stock when read."},{"vendor":"impact-guns","url":"https://www.impactguns.com/AR-15-Parts/B5-Systems-PGR-1122-Bravo-Ergonomic-Pistol-Grip-AR-15-M-4-Black-Polymer-814927020450-PGR-001-01/","price":17.78,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The black one: the page's title says 'B5 Systems PGR-1122 Bravo Ergonomic Pistol Grip' and its text 'This B5 System's Type 23 P-Grip offers a drop in upgrade' (Manufacturer Number: PGR-001-01, its own SKU 814927020450); its offer markup names no number (`make offers ARGS=\"show <url>\"`, 2026-10-19: 17.28 USD, sku=- mpn=-)."}],"bad-workhorse-lower":[{"vendor":"battle-arms","url":"https://battlearmsdevelopment.com/shop/wh556-lr-blk-workhorse-forged-7075-t6-lower-receiver-stripped-black-anodized-ar15-956","price":131.95,"options":{"receiver":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"redcon1","url":"https://redcon1tactical.com/battle-arms-development-ar-15-workhorse-forged-lower-receiver.html","price":125,"sku":"WH556LR","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"rifle-supply","url":"https://riflesupply.com/Battle-Arms-Development-Workhorse-AR-15-Receiver-Lower-Receiver-223-REM-556-NATO-Black-WH556-LR_p_7245.html","price":125.99,"options":{"receiver":"black"},"sku":"7245","in_stock":false,"observed":"2026-11-21","via":"harvest"}],"bca-556-16-mid-barrel":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/bear-creek-arsenal-16in-5-56-nato-1-7-mid-length-ar-15-barrel-parkerized","price":59.99,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (the number is in its title and its address); the markup names no number"},{"vendor":"bear-creek","url":"https://www.bearcreekarsenal.com/556-16-parkerized-m4-barrel-1-7-twist-mid-length.html","price":62.93,"sku":"1343-B556MM41617(P)","in_stock":true,"observed":"2026-10-26","via":"harvest"},{"vendor":"right-to-bear","url":"https://www.righttobear.com/bear-creek-16-m4-mid-barrel-5-56-1343-b556mm41617/","price":124.99,"sku":"1343-B556MM41617","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"redcon1","url":"https://redcon1tactical.com/bear-creek-arsenal-16-contour-4150-parkerized-5-56-mid-length-1-7-barrel.html","price":123.95,"sku":"1343-B556MM41617(P)","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/16-5-56-nato-17-twist-mid-length-parkerized-barrel/","price":79.95,"sku":"1374","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/collections/barrel/products/bca-16-5-56-nato-1-7-twist-mid-length-parkerized-barrel","price":79.95,"sku":"1374","in_stock":true,"observed":"2026-11-21","via":"harvest"}],"bca-stripped-lower":[{"vendor":"bear-creek","url":"https://www.bearcreekarsenal.com/guns-parts/ar-15/ar-15-lowers/stripped-lower-receivers/bca-ar-15-lower-receiver-multi-caliber-black-anodized.html","price":69.99,"options":{"receiver":"black"},"sku":"LR-15","in_stock":true,"observed":"2026-10-26","via":"harvest"},{"vendor":"bear-creek","url":"https://www.bearcreekarsenal.com/bca-ar-15-lower-receiver-multi-caliber-flat-dark-earth-cerakote.html","price":109.99,"options":{"receiver":"fde"},"sku":"LR-15FDE","in_stock":true,"observed":"2026-10-26","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/bear-creek-arsenal-multi-cal-stripped-ar-15-lower-stripped-lower","price":69.95,"options":{"receiver":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (the number is in its title and its address); the markup names no number"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/bca-bc-15-ar-15-forged-stripped-lower-receiver/","price":49.95,"options":{"receiver":"black"},"sku":"34198","in_stock":true,"observed":"2026-11-21","via":"harvest"}],"bcm-115-carbine-barrel":[{"vendor":"bcm","url":"https://bravocompanyusa.com/bcm-standard-11-5-carbine-barrel-stripped-nfa/","price":279,"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The maker's own shop: its page is this one product (SKU: BCM-BRL-s-11-STD in its text); the markup's offer names no number"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/bravo-company-bcm-ar-15-barrel-11.5in-5.56-nato-carbine-length-govt-profile","price":279,"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (SKU and MPN BCM-BRL-S-11-STD in its text); the markup names no number"}],"bcm-145-mid-barrel":[{"vendor":"bcm","url":"https://bravocompanyusa.com/bcm-standard-14-5-mid-length-barrel-stripped/","price":279,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The maker's own shop: its page is this one product (SKU: BCM-BRL-s-MID-14-STD in its text); the markup's one offer names no number"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/bravo-company-manufacturing-5-56-nato-1-7-mid-length-govt-profile-ar-15-barrel-14-5in","price":279,"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (SKU and MPN BCM-BRL-S-MID-14-STD in its text); the markup's two offers are the same price and name no number"}],"bcm-16-mid-barrel":[{"vendor":"bcm","url":"https://bravocompanyusa.com/bcm-standard-16-mid-length-barrel-stripped/","price":279,"in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/bravo-company-manufacturing-standard-16-mid-length-barrel-stripped-bcm-brl-s-mid-16-std","price":279,"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (the number is in its title and its address); the markup names no number"}],"bcm-625-gas-block":[{"vendor":"bcm","url":"https://bravocompanyusa.com/bcm-low-profile-gas-block-steel-with-set-screws-625/","price":44.95,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"BCM's own page for BCM-LGB-625; the markup's one offer names no number"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/bravo-company-mfg-low-profile-gas-block-625-set-screw-style-bcm-lgb-625","price":44.95,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (the number is in its title and its address); the markup names no number"},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/1025636846?pid=594888","price":44.95,"sku":"594888","in_stock":true,"observed":"2026-10-30","via":"harvest","note":"MidwayUSA's own number for the .625 choice of its one page for the two sizes (manufacturer number BCM-LGB-625)"},{"vendor":"kygunco","url":"https://www.kygunco.com/product/bravo-company-bcm-lgb-625-bcm-low-profile-gas-block-625","price":44.95,"sku":"229547","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The markup's number is the seller's own; its mpn is BCM-LGB-625"},{"vendor":"gritr-sports","url":"https://gritrsports.com/bravo-company-ar-15-625-gas-block-bcm-lgb-625","price":38.99,"sku":"BRA-BCM-LGB-625","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"rifle-supply","url":"https://riflesupply.com/BCM-Low-Profile-Gas-Block-625-ID_p_1846.html","price":50.99,"sku":"1846","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The markup's number is the seller's own; its mpn is BCM-LGB-625"}],"bcm-750-gas-block":[{"vendor":"bcm","url":"https://bravocompanyusa.com/bcm-low-profile-gas-block-steel-with-set-screws-750/","price":44.95,"in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/bravo-company-mfg-low-profile-gas-block-750-set-screw-style-bcm-lgb-750","price":44.95,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (the number is in its title and its address); the markup names no number"},{"vendor":"alexanders","url":"https://alexandersstore.com/product/bcm-low-profile-gas-block-750-bbl/","price":44.95,"sku":"LGB750","in_stock":true,"observed":"2026-11-18","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/bcmgunfighter-750-low-profile-gas-block/","price":44.95,"sku":"3503","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"sportsmans","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/gun-parts-magazines/rifle-parts/gas-blocks/bravo-company-750-low-profile-gas-block/p/1697744","price":32.92,"sku":"1697744","in_stock":false,"observed":"2026-11-21","via":"harvest"}],"bcm-bcg":[{"vendor":"bcm","url":"https://bravocompanyusa.com/bcm-bolt-carrier-group-mpi-auto/","price":199,"in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/bravo-company-manufacturing-bolt-carrier-group-bcm-bcg","price":199,"in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"aerospace-arms","url":"https://aerospacearms.com/bravo-company-m16-bolt-carrier-group/","price":220,"sku":"100020758","in_stock":true,"observed":"2026-11-21","via":"harvest"}],"bcm-carbine-action-spring":[{"vendor":"bcm","url":"https://bravocompanyusa.com/carbine-action-spring/","price":4.5,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (BCM's number for it is SPRING-CARBINE-ACTION); its offer markup names no number."}],"bcm-carbine-buffer":[{"vendor":"bcm","url":"https://bravocompanyusa.com/carbine-buffer/","price":17.95,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (BCM's number for it is Buffer-Carbine); its offer markup names no number. The page gives $20.00 as MSRP."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/bravo-company-manufacturing-carbine-buffer-3-0-oz","price":17.95,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The page's text gives SKU and MPN Buffer-Carbine; its offer markup names no number (two offers, one price)."}],"bcm-castle-nut":[{"vendor":"bcm","url":"https://bravocompanyusa.com/receiver-extension-nut-castle-nut/","price":7,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (BCM's number for it is CASTLE-NUT-AR15); its offer markup names no number."}],"bcm-delta-ring-assembly":[{"vendor":"bcm","url":"https://bravocompanyusa.com/delta-ring-assembly-ar15/","price":10.5,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (BCM's number for it is DELTA-RING-ASSEMBLY-AR15); its offer markup names no number (make offers show, 2026-10-28: 10.50 USD, sku -)."}],"bcm-end-plate":[{"vendor":"bcm","url":"https://bravocompanyusa.com/receiver-end-plate/","price":4,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (BCM's number for it is RECEIVER-END-PLATE); its offer markup names no number."}],"bcm-front-sight-base-f-750":[{"vendor":"bcm","url":"https://bravocompanyusa.com/front-sight-base-f-fsb-id-750-milspec-for-flat-top-uppers/","price":29.95,"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The maker's own page of this one product (SKU Front-Sight-Base-F-750 on the page); the markup names no number"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/bravo-company-manufacturing-ar-15-front-sight-post-gas-block-f-marked-for-flat-top-upper","price":29.95,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (BCM's F-marked .750 base, in its title); the markup names no number, and carries the one price twice"}],"bcm-gi-barrel-nut":[{"vendor":"bcm","url":"https://bravocompanyusa.com/g-i-barrel-nut-ar15/","price":8.95,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (BCM's number for it is Barrel-Nut-G.I.); its offer markup names no number (make offers show, 2026-10-28: 8.95 USD, sku -)."}],"bcm-grip-mod-3":[{"vendor":"bcm","url":"https://bravocompanyusa.com/bcm-grip-mod-3-black/","price":19.95,"options":{"body":"black"},"sku":"BCM-GFG-Mod-3-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"bcm","url":"https://bravocompanyusa.com/bcm-grip-mod-3-flat-dark-earth/","price":19.95,"options":{"body":"fde"},"sku":"BCM-GFG-Mod-3-FDE","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/bravo-company-gunfighter-grip-mod-3-black-bcm-gfg-mod-3-black","price":19.95,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (the number is in its title and its address); the markup names no number"},{"vendor":"wing-tactical","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/grips-foregrips/pistol-grips/bravo-company-bcmgunfighter-pistol-grip-mod-3/","price":17.95,"options":{"body":"black"},"sku":"BCM-GFG-MOD-3","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One page and one price for Black and Flat Dark Earth."},{"vendor":"right-to-bear","url":"https://www.righttobear.com/bcm-gunfighter-grip-mod-3-black-bcm-gfg-mod-3-blk/","price":20,"options":{"body":"black"},"sku":"BCM-GFG-MOD-3-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"kygunco","url":"https://www.kygunco.com/product/bravo-company-bcm-gfg-mod-3-black-bcm-gunfighter-grip-mod-3-black","price":17.95,"options":{"body":"black"},"sku":"211693","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/bcmgunfighter-grip-844513","price":20,"options":{"body":"black"},"sku":"844515","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One page for Mod 3 in Black and FDE; 844515 is its 'BCMGUNFIGHTER Grip - Mod 3, Black'."},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/bcmgunfighter-grip-844513","price":20,"options":{"body":"fde"},"sku":"844516","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"844516 is its 'BCMGUNFIGHTER Grip - Mod 3, FDE'."},{"vendor":"alexanders","url":"https://alexandersstore.com/product/bcm-gunfighter-grip-mod-3-blk/","price":19.99,"options":{"body":"black"},"sku":"BCM-GFG-MOD-3-BLACK","in_stock":true,"observed":"2026-10-27","via":"harvest"},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/bcmgunfighter-pistol-grip-mod-3/","price":19.95,"options":{"body":"black"},"sku":"3500","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One page for four colours; 3500 is its Black."},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/bcmgunfighter-pistol-grip-mod-3/","price":19.95,"options":{"body":"fde"},"sku":"3540","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"3540 is its 'BCMGUNFIGHTER Pistol Grip - MOD 3 - FDE'."},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/bcmgunfighter-pistol-grip-mod-3/","price":19.95,"options":{"body":"fg"},"sku":"3538","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"3538 is its Foliage Green (out of stock on 2026-10-06)."},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/bcmgunfighter-pistol-grip-mod-3/","price":19.95,"options":{"body":"wg"},"sku":"3539","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"3539 is its Wolf Grey (out of stock on 2026-10-06)."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/bcmgunfighter-pistol-grip-mod-3/","price":19.95,"options":{"body":"black"},"sku":"3500","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"One page for four colours; 3500 is its Black."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/bcmgunfighter-pistol-grip-mod-3/","price":19.95,"options":{"body":"fde"},"sku":"3540","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"3540 is its fde."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/bcmgunfighter-pistol-grip-mod-3/","price":19.95,"options":{"body":"fg"},"sku":"3538","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"3538 is its foliage-green."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/bcmgunfighter-pistol-grip-mod-3/","price":19.95,"options":{"body":"wg"},"sku":"3539","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"3539 is its wolf-grey."},{"vendor":"rifle-supply","url":"https://riflesupply.com/BCM-Gunfighter-Grip-Mod-3-Black_p_1841.html","price":23.99,"options":{"body":"black"},"sku":"1841","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"sportsmans","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/gun-parts-accessories/gun-parts-magazines/rifle-parts/rifle-grips/bravo-company-gunfighter-mod-3-pistol-grip-black/p/1697749","price":19.99,"options":{"body":"black"},"sku":"1697749","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/1025633544","price":19.95,"options":{"body":"black"},"sku":"670545","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The page lists the grip's colours; 670545 is MidwayUSA's own number for the black one in its markup (\"... Pistol Grip Black\", UPC 855877004183)."}],"bcm-grip-mod-4":[{"vendor":"bcm","url":"https://bravocompanyusa.com/bcm-grip-mod-4-black/","price":17.95,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"BCM's page for the black grip (SKU row BCM-GFG-MOD-4-BLK); its markup's one offer names no number."},{"vendor":"bcm","url":"https://bravocompanyusa.com/bcm-grip-mod-4-flat-dark-earth/","price":17.95,"options":{"body":"fde"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"BCM's page for the FDE grip (SKU row BCM-GFG-MOD-4-FDE); its markup's one offer names no number."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/bravo-company-manufacturing-grip-mod-4-black","price":17.95,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (SKU and MPN BCM-GFG-MOD-4-BLK in its text); the markup carries one price twice and names no number."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/bravo-company-manufacturing-grip-mod-4-flat-dark-earth","price":17.95,"options":{"body":"fde"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product, the FDE grip; the markup carries one price twice and names no number."},{"vendor":"kygunco","url":"https://www.kygunco.com/product/bravo-company-mod-4-grip-fits-ar-rifles-black","price":17.95,"options":{"body":"black"},"sku":"289406","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"KYGUNCO's own number; its markup's mpn is BCM-GFG-MOD-4-BLK."}],"bcm-h-buffer":[{"vendor":"bcm","url":"https://bravocompanyusa.com/h-carbine-buffer/","price":73.6,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (BCM's number for it is Buffer-Carbine-H); its offer markup names no number. The page gives $79.00 as MSRP and a limit of 5 to an order."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/bravo-company-manufacturing-carbine-h1-buffer-3-8-oz","price":69.95,"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The page's text gives SKU and MPN Buffer-Carbine-H; its offer markup names no number (two offers, one price)."}],"bcm-h2-buffer":[{"vendor":"bcm","url":"https://bravocompanyusa.com/h2-carbine-buffer/","price":133.25,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (BCM's number for it is Buffer-Carbine-H2); its offer markup names no number. The page gives $141.00 as MSRP and a limit of 5 to an order."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/bravo-company-usa-carbine-h2-buffer-weight-4.6oz.","price":125.9,"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The page's text gives SKU and MPN BUFFER-CARBINE-H2; its offer markup names no number (two offers, one price)."}],"bcm-h3-buffer":[{"vendor":"bcm","url":"https://bravocompanyusa.com/h3-carbine-buffer/","price":192.9,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (BCM's number for it is Buffer-Carbine-H3); its offer markup names no number. The page gives $204.00 as MSRP and a limit of 5 to an order."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/bravo-company-manufacturing-carbine-h3-buffer-5-4-oz","price":181.85,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The page's text gives SKU and MPN Buffer-Carbine-H3; its offer markup names no number (two offers, one price)."}],"bcm-handguard-cap-round-750":[{"vendor":"bcm","url":"https://bravocompanyusa.com/handguard-cap-round-750-ar15","price":3,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (BCM's number for it is Handguard-Cap-Round-.750-AR15); its offer markup names no number."}],"bcm-handguard-cap-triangle-750":[{"vendor":"bcm","url":"https://bravocompanyusa.com/handguard-cap-triangle-750-ar15/","price":3,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (BCM's number for it is Handguard-Cap-Triangle-.750); its offer markup names no number."}],"bcm-kag-mlok":[{"vendor":"bcm","url":"https://bravocompanyusa.com/bcm-kag-black-m-lok-compatible/","price":18.95,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"BCM's page for the black KAG (SKU: BCM-KAG-MCMR-BLK on the page); its markup's offer names no number."},{"vendor":"bcm","url":"https://bravocompanyusa.com/bcm-kag-flat-dark-earth-m-lok-compatible/","price":18.95,"options":{"body":"fde"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"BCM's page for the FDE KAG (SKU: BCM-KAG-MCMR-FDE on the page); its markup's offer names no number."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/bcm-gunfighter-kag-grip-m-lok-black","price":18.95,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (BCM-KAG-MCMR-BLK in its spec table); its markup names no number, and carries the one price twice."},{"vendor":"rifle-supply","url":"https://riflesupply.com/BCM-Gunfighter-Kinesthetic-Angled-Grip-KAG-MLOK-Black-BCM-KAG-MCMR-BLK_p_1858.html","price":21.99,"options":{"body":"black"},"sku":"1858","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"sportsmans","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/gun-parts-accessories/gun-parts-magazines/rifle-parts/rifle-grips/bravo-company-kag-m-lok-foregrip/p/1697740","price":19.99,"options":{"body":"black"},"sku":"1697740","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Out of stock on 2026-10-19."},{"vendor":"kygunco","url":"https://www.kygunco.com/product/bravo-company-bcm-kag-mcmr-blk-bcm-gunfighter-kag-black-m-lok-compatible","price":18.95,"options":{"body":"black"},"sku":"211692","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"right-to-bear","url":"https://www.righttobear.com/bcm-m-lok-kag-angled-grip-blk-bcm-kag-mcmr-blk/","price":21,"options":{"body":"black"},"sku":"BCM-KAG-MCMR-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest"}],"bcm-m4-upper":[{"vendor":"bcm","url":"https://bravocompanyusa.com/bcm-m4-upper-receiver-assembly-w-laser-t-markings/","price":129,"in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/bravo-company-manufacturing-m4-upper-receiver-assembly-w-laser-t-markings-bcm4-ur-m4","price":129,"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Titled \"Bravo Company Manufacturing M4 Stripped AR-15 Upper Receiver\" under BCM4-UR-M4, with the rows \"Forward Assist: Assembled with Forward Assist\" and \"Port Door: Assembled with Port Cover\": the seller's title, the same product."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/bcmgunfighter-assembled-upper-receiver/","price":129,"sku":"3506","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Its own number 3506; \"MPN BCM4-UR-M4 UPC 855877004442\"."},{"vendor":"rifle-supply","url":"https://riflesupply.com/BCM-Upper-Receiver-Assembly-Flat-Top-M4_p_1798.html","price":131.99,"sku":"1798","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"aerospace-arms","url":"https://aerospacearms.com/bravo-company-m4-upper-receiver-assembly-with-laser-t-markings/","price":144.95,"sku":"BCM4-UR-M4","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"right-to-bear","url":"https://www.righttobear.com/bcm-m4-upper-receiver-assembly-w-laser-t-marking-bcm4-ur-m4/","price":149,"sku":"BCM4-UR-M4","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"alexanders","url":"https://alexandersstore.com/product/bcm-upper-rec-assembly-ft-m4/","price":143.99,"sku":"4URM4","in_stock":false,"observed":"2026-11-18","via":"harvest","note":"Its part number reads 4URM4 (a distributor's), with BCM's UPC 855877004442 and photos named BCM4-UR-M4: to be confirmed when its offer is read."}],"bcm-mcmr-10-handguard":[{"vendor":"bcm","url":"https://bravocompanyusa.com/bcm-mcmr-10-m-lok-compatible-modular-rail/","price":214.95,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (its text: SKU: BCM-MCMR-10-556-BLK); the markup names no number."},{"vendor":"bcm","url":"https://bravocompanyusa.com/bcm-mcmr-10-m-lok-compatible-modular-rail-flat-dark-earth/","price":214.95,"options":{"body":"fde"},"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product in Flat Dark Earth (its text: SKU: BCM-MCMR-10-556-FDE); the markup names no number."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/bcm-10-mlok-compatible-modular-rail-bcm-mcmr-10-556-blk","price":214.95,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (the number is in its text and its address); the markup names no number, and states the one price twice. Primary Arms has a second address for the same product (bravo-company-mfg-mcmr-10-modular-rail-handguard-m-lok-compatible-10.5in): not listed twice."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/bravo-company-manufacturing-mcmr-modular-rail-ar-15-handguard-fde-10in","price":214.95,"options":{"body":"fde"},"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product in Flat Dark Earth (its text: SKU: BCM-MCMR-10-556-FDE); the markup names no number, and states the one price twice."},{"vendor":"kygunco","url":"https://www.kygunco.com/product/bravo-company-bcm-mcmr-10-556-blk-bcm-gunfighter-mcmr-aluminum-rail-5.56-10-blk","price":214.95,"options":{"body":"black"},"sku":"BCM-MCMR-10-556-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"rifle-supply","url":"https://riflesupply.com/BCM-Gunfighter-Mlok-MCMR-Modular-Rail-System-10-Black-BCM-MCMR-10-556-BLK_p_1854.html","price":234.99,"options":{"body":"black"},"sku":"BCM-MCMR-10-556-BLK","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/bcm-gunfighter-mcmr-m-lok-modular-rail/","price":214.95,"options":{"body":"black"},"sku":"4715","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"One page for every length (the 15's seed has it too): the markup's 4715 is its 10.5 in, and the page's numbers are the black ones (MPN BCM-MCMR-10-556-BLK among them)."}],"bcm-mcmr-13-handguard":[{"vendor":"bcm","url":"https://bravocompanyusa.com/bcm-mcmr-13-m-lok-compatible-modular-rail/","price":224.95,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (its text: SKU: BCM-MCMR-13-556-BLK); the markup names no number."},{"vendor":"bcm","url":"https://bravocompanyusa.com/bcm-mcmr-13-m-lok-compatible-modular-rail-flat-dark-earth/","price":224.95,"options":{"body":"fde"},"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product in Flat Dark Earth (its text: SKU: BCM-MCMR-13-556-FDE); the markup names no number."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/bcm-13-mlok-compatible-modular-rail-bcm-mcmr-13-556-blk","price":224.95,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (the number is in its address); the markup names no number, and states the one price twice."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/bravo-company-manufacturing-mcmr-13-modular-rail-ar-15-handguard-13-4in-fde","price":224.95,"options":{"body":"fde"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product in Flat Dark Earth (its text: SKU: BCM-MCMR-13-556-FDE MPN: BCM-MCMR-13-556-FDE); the markup names no number, and states the one price twice."},{"vendor":"kygunco","url":"https://www.kygunco.com/product/bravo-company-bcm-mcmr-13-556-blk-bcm-gunfighter-mcmr-aluminum-rail-5.56-13-blk","price":224.95,"options":{"body":"black"},"sku":"229544","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The markup's one offer carries the seller's own number, 229544, and the maker's as its mpn (BCM-MCMR-13-556-BLK)."},{"vendor":"gritr-sports","url":"https://gritrsports.com/bravo-company-mcmr-556-13in-rail-bcm-mcmr-13-556-blk","price":195.81,"options":{"body":"black"},"sku":"BCM-BCM-MCMR-13-556-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The seller's own number as the markup carries it (the maker's with the seller's prefix for the brand in front; its mpn is BCM-MCMR-13-556-BLK), stated twice at one price; the page's markup also carries another product's offer (a bag), which the number leaves out."},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/bcm-gunfighter-mcmr-m-lok-modular-rail/","price":224.95,"options":{"body":"black"},"sku":"4716","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"One page for every length (the 10's and the 15's seeds have it too): the markup's 4716 is its 13 in (\"BCM Gunfighter MCMR M-LOK Modular Rail - 13\"\"), and the page's numbers are the black ones (MPN BCM-MCMR-13-556-BLK among them)."},{"vendor":"trex-arms","url":"https://trex-arms.com/store/bcm-5-56-handguard","price":224.95,"options":{"body":"black"},"sku":"1332316","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One page for six of BCM's handguards in two colours: the markup's 1332316 is \"BCM AR-15 Handguard - MCMR-13, Black\"."},{"vendor":"trex-arms","url":"https://trex-arms.com/store/bcm-5-56-handguard","price":224.95,"options":{"body":"fde"},"sku":"1332317","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The same page: the markup's 1332317 is \"BCM AR-15 Handguard - MCMR-13, FDE\"."}],"bcm-mcmr-15-handguard":[{"vendor":"bcm","url":"https://bravocompanyusa.com/bcm-mcmr-15-m-lok-compatible-modular-rail/","price":234.95,"options":{"body":"black"},"sku":"BCM-MCMR-15-556-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"bcm","url":"https://bravocompanyusa.com/bcm-mcmr-15-m-lok-compatible-modular-rail-flat-dark-earth/","price":234.95,"options":{"body":"fde"},"sku":"BCM-MCMR-15-556-FDE","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/bravo-company-manufacturing-mcmr-modular-rail-ar-15-handguard-fde-15in","price":234.95,"options":{"body":"fde"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product in Flat Dark Earth (its title: MCMR Free Float AR-15 Handguard - M-LOK - 15\" - FDE); the markup names no number, and states the one price twice."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/bcm-15-mlok-compatible-modular-rail-bcm-mcmr-15-556-blk","price":234.95,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (the number is in its title and its address); the markup names no number"},{"vendor":"right-to-bear","url":"https://www.righttobear.com/bcm-mcmr-m-lok-free-float-handguard-15-bcm-mcmr-15-556-blk/","price":250,"options":{"body":"black"},"sku":"BCM-MCMR-15-556-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"kygunco","url":"https://www.kygunco.com/product/bravo-company-bcm-mcmr-15-556-blk-bcm-gunfighter-mcmr-aluminum-rail-5.56-15-blk","price":234.95,"options":{"body":"black"},"sku":"229545","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"impact-guns","url":"https://www.impactguns.com/accessories/bcm-mcmr-15-556-blk-mcmr-alum-rail-mlok-15-812526021618-mcmr15556blk/","price":234.95,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"scheels","url":"https://www.scheels.com/p/bravo-company-bcm-mcmr-15%22-m-lok--modular-rail/18914-BCM-MCMR-15-556-BLK/","price":239.99,"options":{"body":"black"},"sku":"81252602161","in_stock":true,"observed":"2026-10-05","via":"harvest"},{"vendor":"alexanders","url":"https://alexandersstore.com/product/bcm-gunftr-mcmr-rail-556-15-blk-mlk/","price":234.95,"options":{"body":"black"},"sku":"MCMR15556BLK","in_stock":true,"observed":"2026-11-18","via":"harvest"},{"vendor":"rifle-supply","url":"https://riflesupply.com/bcm-gunftr-mcmr-rail-556-15-blk-mlk/","price":234.99,"options":{"body":"black"},"sku":"DSHIP-BCM-MCMR-15-556-BLK","in_stock":false,"observed":"2026-11-21","via":"harvest"}],"bcm-mid-gas-tube":[{"vendor":"bcm","url":"https://bravocompanyusa.com/gas-tube-mid-length/","price":15,"in_stock":true,"observed":"2026-11-21","via":"harvest"}],"bcm-mk2-buffer-t0":[{"vendor":"bcm","url":"https://bravocompanyusa.com/bcm-mk2-buffer-t0","price":36.95,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (BCM's number for it is BCM-BFMK2-M1-T0, in the page's text); its offer markup names no number. $36.95, MSRP $49.00 (2026-10-28)."}],"bcm-mk2-charging-handle":[{"vendor":"bcm","url":"https://bravocompanyusa.com/bcm-ambidextrous-mk2-charging-handle-large-latch-5-56mm-223/","price":89.95,"in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/bravo-company-manufacturing-gunfighter-mk2-ambidextrous-charging-handle-large-latch","price":89.95,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (the number is in its title and its address); the markup names no number"},{"vendor":"scheels","url":"https://www.scheels.com/p/bcm-ambidextrous-mk2-charging-handle/5270-BCM-GFH-MK2-LRG-AMBI/","price":89.99,"sku":"81252602380","in_stock":true,"observed":"2026-10-05","via":"harvest","note":"Its page's number 5270-BCM-GFH-MK2-LRG-AMBI holds BCM's; gtin 812526023803."},{"vendor":"alexanders","url":"https://alexandersstore.com/product/bcm-gfhmk2lrgambi-ambidextrous-mk2-charging-handle-compatible-w-mil-spec-ar-15-black-7075-t-6-aluminum/","price":89.95,"sku":"BCM-GFH-MK2-LRG-AMBI","in_stock":true,"observed":"2026-11-18","via":"harvest","note":"mpn GFHMK2LRGAMBI, gtin12 812526023803. Its photo is of the medium handle (laser marked MED); its 'Overall Length 9.25 in' is not the handle's."},{"vendor":"faxon","url":"https://faxonfirearms.com/GFHMK2LRGAMBI","price":91.95,"sku":"167850","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"A drop-ship listing ('Ships From Sports South'), sku 167850, mpn GFHMK2LRGAMBI, upc 812526023803."}],"bcm-mk2-lower-no-stock":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/bcm-mk2-ar-15-complete-lower-receiver-no-stock","price":524,"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Primary Arms' page of LRG-RMS-NO-STOCK; its markup names no number (two microdata offers, one price)."}],"bcm-mk2-receiver-extension":[{"vendor":"bcm","url":"https://bravocompanyusa.com/bcm-MK2-receiver-extension/","price":49.95,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (BCM's number for it is BCM-MK2-RE, in the page's text); its offer markup names no number. $49.95, MSRP $55.00 (2026-10-28)."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/bravo-company-manufacturing-mk2-receiver-extension","price":49.95,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The page's text gives SKU and MPN BCM-MK2-RE; its offer markup names no number (two offers, one price, $49.95, 2026-10-28)."}],"bcm-mk2-rms-m1t0":[{"vendor":"bcm","url":"https://bravocompanyusa.com/bcm-mk2-recoil-mitigation-system-mod-1-t0/","price":110.95,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"BCM's own page for the kit; its markup names no number (one microdata offer)."}],"bcm-pmcr-carbine":[{"vendor":"bcm","url":"https://bravocompanyusa.com/bcm-pmcr-polymer-m-lok-rail-carbine-length-black/","price":30.95,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (BCM's number for it is BCM-PMCR-CAR-BLK); its offer markup names no number."}],"bcm-pmcr-mid":[{"vendor":"bcm","url":"https://bravocompanyusa.com/bcm-pmcr-polymer-m-lok-rail-mid-length-black/","price":31.95,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (BCM's number for it is BCM-PMCR-MID-BLK); its offer markup names no number."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/bravo-company-manufacturing-bcmgunfighter-pmcr-polymer-m-lok-compatible-rail-mid-length","price":31.95,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (its SKU and MPN BCM-PMCR-MID-BLK in its text); its markup carries two offers at one price and names no number."}],"bcm-pnt-trigger":[{"vendor":"bcm","url":"https://bravocompanyusa.com/bcm-pnt-trigger-assembly-ar15/","price":65.95,"sku":"BCM-PNT-TA1","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/bravo-company-pnt-trigger-assembly-ar-15-bcm-pnt-ta1","price":65.95,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (the number is in its title and its address); the markup names no number"},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/1025637997","price":65.95,"sku":"290660","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page's data names BCM-PNT-TA1 and UPC 812526020451; MidwayUSA's own number in its markup is 290660."},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/bcm-pnt-trigger-assembly-ar-15-950472","price":65.95,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"No SKU or MPN on the page; its address and title name the product."},{"vendor":"kygunco","url":"https://www.kygunco.com/product/bravo-company-bcm-pnt-ta1-bcm-gunfighter-pnt-trigger-assembly-ar-15","price":65.95,"sku":"229571","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"MPN BCM-PNT-TA1, UPC 812526020451."},{"vendor":"alexanders","url":"https://alexandersstore.com/product/bcm-pnt-trigger-assembly-ar15/","price":65.95,"sku":"BCM-PNT-TA1","in_stock":true,"observed":"2026-11-18","via":"harvest","note":"mpn BCM-PNT-TA1, gtin12 812526020451."},{"vendor":"rifle-supply","url":"https://riflesupply.com/BCM-Polished-Nickel-Teflon-Trigger-Assembly-AR15_p_1889.html","price":69.99,"sku":"1889","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"MPN BCM-PNT-TA1."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/bcm-ar-15-pnt-trigger-assembly/","price":65.95,"sku":"5414","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"MPN BCM-PNT-TA1 in its Additional information."}],"bcm-qd-end-plate":[{"vendor":"bcm","url":"https://bravocompanyusa.com/bcm-qd-end-plate/","price":16.95,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (BCM's number for it is BCM-EPM4-QD); its offer markup names no number. The page gives $20.00 as MSRP."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/bravo-company-gunfighter-qd-end-plate-bcm-epm4-qd","price":16.95,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The page's text gives SKU and MPN BCM-EPM4-QD; its offer markup names no number (two offers, one price)."},{"vendor":"kygunco","url":"https://www.kygunco.com/product/bravo-company-bcm-epm4-qd-bcm-gunfighter-qd-end-plate","price":16.95,"sku":"BCM-EPM4-QD","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The markup carries BCM's number as mpn and the seller's item number 211695 as sku."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/bcmgunfighter-qd-end-plate/","price":16.95,"sku":"4328","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"MPN BCM-EPM4-QD, UPC 812526020109 on the page; the markup carries the seller's own number (4328)."},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/bcm-qd-end-plate-306433","price":18,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product ('1x BCM Gunfighter QD End Plate'); it names no number, and neither does its offer markup."}],"bcm-receiver-extension":[{"vendor":"bcm","url":"https://bravocompanyusa.com/bcm-milspec-carbine-receiver-extension-buffer-tube-6-position/","price":38.95,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (BCM's number for it is BCM-Milspec-RE); its offer markup names no number. The page gives $45.00 as the regular price."}],"bcm-rifle-m16-action-spring":[{"vendor":"bcm","url":"https://bravocompanyusa.com/rifle-m16-action-spring/","price":4.5,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (BCM's number for it is SPRING-RIFLE-M16-ACTION, in the page's text); its offer markup names no number. $4.50 (2026-10-28)."}],"bcm-stock-kit":[{"vendor":"bcm","url":"https://bravocompanyusa.com/bcm-milspec-carbine-stock-hardware-mounting-kit-mil-spec/","price":61.95,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"BCM's sale price that day; the page gives $69.00 as the regular price."}],"bcm-stock-mod-0":[{"vendor":"bcm","url":"https://bravocompanyusa.com/bcm-stock-mod-0-black/","price":55.95,"options":{"body":"black"},"sku":"BCM-GFS-MOD-0-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"bcm","url":"https://bravocompanyusa.com/bcm-stock-assembly-flat-dark-earth/","price":55.95,"options":{"body":"fde"},"sku":"BCM-GFS-Mod-0-FDE","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/bravo-company-manufacturing-bcm-gunfighter-mod-0-stock-black","price":55.95,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (BCM-GFS-MOD-0-BLK in its text); the markup names no number"},{"vendor":"wing-tactical","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/stocks-accessories/bravo-company-bcmgunfighter-mod-0-stock/","price":55.95,"options":{"body":"black"},"sku":"BCM-GFS-MOD-0","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One page and one price for Black and Flat Dark Earth."},{"vendor":"right-to-bear","url":"https://www.righttobear.com/Bravo-Company-GUNFIGHTER-Stock-Mod-0-Black-p/bcm-gfs-mod-0-blk.htm","price":60,"options":{"body":"black"},"sku":"BCM-GFS-MOD-0-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"impact-guns","url":"https://www.impactguns.com/parts/bravo-company-gunfighter-mod-0-stock-black-finish-855877004916-bcm-gfs-mod-0-blk/","price":55.89,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (UPC 855877004916, and BCM-GFS-MOD-0-BLK in its address); the markup names no number."},{"vendor":"kygunco","url":"https://www.kygunco.com/product/bravo-company-bcm-gfs-mod-0-blk-bcm-gunfighter-stock-mod-0-black","price":55.95,"options":{"body":"black"},"sku":"211698","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/bcmgunfighter-stock-884400","price":55.95,"options":{"body":"black"},"sku":"884401","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One page for Mod 0 in Black and FDE; 884401 is its 'BCMGUNFIGHTER Stock - Mod 0, Black' (884402 the FDE)."},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/bcmgunfighter-stock-884400","price":55.95,"options":{"body":"fde"},"sku":"884402","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"884402 is its 'BCMGUNFIGHTER Stock - Mod 0, FDE'."},{"vendor":"alexanders","url":"https://alexandersstore.com/product/bcm-gunfighter-stock-mod-0-blk/","price":55.95,"options":{"body":"black"},"sku":"BCM-GFS-MOD-0-BLK","in_stock":true,"observed":"2026-11-18","via":"harvest","note":"The page's markup gives the number as its mpn (and gtin12 855877004916)."},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/bcmgunfighter-stock-mod-0/","price":55.95,"options":{"body":"black"},"sku":"3502","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"One page for four colours; 3502 is its Black with BCM's UPC (855877004916). A second Black, 3501, carries another UPC (812526020680) and isn't taken."},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/bcmgunfighter-stock-mod-0/","price":55.95,"options":{"body":"fde"},"sku":"3535","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"3535 is its 'BCMGUNFIGHTER Stock - MOD 0 - FDE'."},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/bcmgunfighter-stock-mod-0/","price":55.95,"options":{"body":"fg"},"sku":"3530","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"3530 is its 'BCMGUNFIGHTER Stock - MOD 0 - Foliage Green' (out of stock on 2026-10-06)."},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/bcmgunfighter-stock-mod-0/","price":55.95,"options":{"body":"wg"},"sku":"3532","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"3532 is its 'BCMGUNFIGHTER Stock - MOD 0 - Wolf Grey' (out of stock on 2026-10-06)."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/bcmgunfighter-stock-mod-0/","price":55.95,"options":{"body":"black"},"sku":"3502","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"The same page and numbers as Dirty Bird's; 3502 is its Black."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/bcmgunfighter-stock-mod-0/","price":55.95,"options":{"body":"fde"},"sku":"3535","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"3535 is its fde."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/bcmgunfighter-stock-mod-0/","price":55.95,"options":{"body":"fg"},"sku":"3530","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"3530 is its foliage-green."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/bcmgunfighter-stock-mod-0/","price":55.95,"options":{"body":"wg"},"sku":"3532","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"3532 is its wolf-grey."}],"bcm-urg-mid-16-mcmr-15":[{"vendor":"bcm","url":"https://bravocompanyusa.com/bcm-standard-16-mid-length-upper-receiver-group-w-bcm-mcmr-15-handguard/","price":789.65,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"BCM-URG-MID-16-MCMR-15, as its page is first shown: the free A2 flash hider, no carrier, no charging handle"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/bravo-company-manufacturing-556-nato-mid-length-barreled-upper-mcmr-15-16in","price":789.65,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"\"Bolt carrier group and charging handle not included\". Its page is this one product (SKU and MPN BCM-URG-MID-16-MCMR-15 in its text); the markup names no number"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/bcm-5-56-nato-mid-length-barreled-upper-mcmr-15-16/","price":689.35,"sku":"8839","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"AR15Discounts' own number in the markup; SKU, MPN and UPC on the page all print BCM-URG-MID-16-MCMR-15"}],"bcm-vertical-grip-mod-3-mlok":[{"vendor":"bcm","url":"https://bravocompanyusa.com/bcm-vertical-grip-mod-3-m-lok-compatible-black/","price":18.95,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"BCM's page for the black one alone (SKU BCM-VG-MCMR-MOD-3-BLK in its text); its markup names no number."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/bcm-gunfighter-mod-3-vertical-grip-m-lok-black","price":18.95,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Primary Arms' page for the black one alone (SKU and MPN BCM-VG-MCMR-MOD-3-BLK in its table); its markup names no number."},{"vendor":"right-to-bear","url":"https://www.righttobear.com/bcmgunfighter-vertical-grip-m-lok-bcm-vg-mcmr-mod-3-blk/","price":21,"options":{"body":"black"},"sku":"BCM-VG-MCMR-MOD-3-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"impact-guns","url":"https://www.impactguns.com/grips/bravo-company-bcmgunfighter-grip-mod-3-bcmgunfighter-polymer-rubber-black-812526021595-vgmcmrmod3bk","price":18.99,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its title and address are this grip's (VGMCMRMOD3BK, UPC 812526021595), its description a pistol grip's; its markup names no number."},{"vendor":"rifle-supply","url":"https://riflesupply.com/BCM-Gunfighter-VG-MCMR-Mod-3-Foregrip-MLOK-Compatible-Color-Options_p_3116.html","price":23.99,"options":{"body":"black"},"sku":"3116","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One page and one price for Black and FDE (UPC 812526021595, the black one's)."},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/BCM-Vertical-Grip-MOD-3/","price":20,"options":{"body":"black"},"sku":"462383","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One page for the Mod 3 on M-LOK and Picatinny in two colours; 462383 is its 'BCMGUNFIGHTER Vertical Grip - Mod 3, M-LOK, Black'."},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/BCM-Vertical-Grip-MOD-3/","price":20,"options":{"body":"fde"},"sku":"889653","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"889653 is its 'BCMGUNFIGHTER Vertical Grip - Mod 3, M-LOK, FDE'."}],"blackdog-22lr-15":[{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/black-dog-machine-sonic-x-ar-15-22-long-rifle-15rd-conversion-magazine/","price":15.95,"options":{"body":"smoke"},"sku":"21685","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"ar15discounts' own number; it calls the translucent smoke body grey. The nylon feed lips Black Dog's own page lists."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/black-dog-machine-sonic-x-ar-15-22-long-rifle-15rd-conversion-magazine/","price":15.95,"options":{"body":"black"},"sku":"21683","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"ar15discounts' own number for black with the nylon feed lips Black Dog's own page lists."}],"blackdog-22lr-25":[{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/black-dog-machine-sonic-x-ar-15-22-long-rifle-25rd-conversion-magazine/","price":15.95,"options":{"body":"smoke"},"sku":"21689","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"ar15discounts' own number; it calls the translucent smoke body grey. The nylon feed lips Black Dog's own page lists."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/black-dog-machine-sonic-x-ar-15-22-long-rifle-25rd-conversion-magazine/","price":15.95,"options":{"body":"black"},"sku":"21687","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"ar15discounts' own number for black with the nylon feed lips Black Dog's own page lists."},{"vendor":"bear-creek","url":"https://www.bearcreekarsenal.com/black-dog-25-rd-22lr-magazine.html","price":21,"options":{"body":"black"},"sku":"SW-25BL-NY","in_stock":true,"observed":"2026-10-26","via":"harvest"}],"cloud-defensive-rein":[{"vendor":"cloud-defensive","url":"https://clouddefensive.com/products/cloud-defensive-rein-black","price":369.99,"options":{"body":"black"},"sku":"REIN 3.0-DF-S-650 BLK","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"alexanders","url":"https://alexandersstore.com/product/cld-def-rein-3-0-complete-kit-blk/","price":399.99,"options":{"body":"black"},"sku":"REIN 3.0-DF-S-650 BLK","in_stock":false,"observed":"2026-11-18","via":"harvest"},{"vendor":"impact-guns","url":"https://www.impactguns.com/weapon-mounted-lights/cloud-defensive-rein-3-0-weaponlight-black-m-lok-mount-850016201928-cd2109dfsblk","price":399.99,"options":{"body":"black"},"in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"kygunco","url":"https://www.kygunco.com/product/cloud-defensive-rein-3.0-100000-candela-1250l-weaponlight-black","price":349.99,"options":{"body":"black"},"sku":"268830","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"rifle-supply","url":"https://riflesupply.com/Cloud-Defense-REIN-30-Weaponlight-1250-Lumens-Black-REIN-30-DF-S-650-BLK_p_7665.html","price":430.99,"options":{"body":"black"},"sku":"7665","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"sportsmans","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/gun-parts-accessories/gun-parts-magazines/weapon-lights/cloud-defensive-rein-30-complete-weapon-light-kit-black/p/1808408","price":399.99,"options":{"body":"black"},"sku":"1808408","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/cloud-defensive-rein-gen-3-high-output-weapon-light/","price":399.99,"options":{"body":"black"},"sku":"18309","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/cloud-defensive-rein-gen-3-high-output-weapon-light/","price":399.99,"options":{"body":"black"},"sku":"18309","in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"cloud-defensive","url":"https://clouddefensive.com/products/cloud-defensive-rein-fde","price":369.99,"options":{"body":"fde"},"sku":"REIN 3.0-DF-S-650 FDE","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"impact-guns","url":"https://www.impactguns.com/weapon-mounted-lights/cloud-defensive-rein-3-0-weaponlight-flat-dark-earth-m-lok-mount-850016201942-cd2109dfsfde","price":399.99,"options":{"body":"fde"},"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"A page of one product: its markup names no number (two offers at the one price, 2026-10-06)."},{"vendor":"kygunco","url":"https://www.kygunco.com/product/cloud-defensive-rein-3.0-100000-candela-1250l-weaponlight-fde","price":349.99,"options":{"body":"fde"},"sku":"268831","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"rifle-supply","url":"https://riflesupply.com/Cloud-Defense-REIN-30-Weaponlight-1250-Lumens-FDE-REIN-30-DF-S-650-FDE_p_7666.html","price":430.99,"options":{"body":"fde"},"sku":"7666","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"sportsmans","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/gun-parts-accessories/gun-parts-magazines/weapon-lights/cloud-defensive-rein-30-complete-weapon-light-kit-flat-dark-earth/p/1808409","price":399.99,"options":{"body":"fde"},"sku":"1808409","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/cloud-defensive-rein-gen-3-high-output-weapon-light/","price":399.99,"options":{"body":"fde"},"sku":"18310","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"One page for black (18309) and FDE (18310)."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/cloud-defensive-rein-gen-3-high-output-weapon-light/","price":399.99,"options":{"body":"fde"},"sku":"18310","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"One page for black (18309) and FDE (18310)."},{"vendor":"cloud-defensive","url":"https://clouddefensive.com/products/rein-3-0-coyote-brown-copy","price":369,"options":{"body":"earth_brown"},"sku":"REIN 3.0 DF-S-650 EARTH BROWN","in_stock":false,"observed":"2026-10-21","via":"harvest"},{"vendor":"gritr","url":"https://gritroutdoors.com/cloud-defensive-rein-3-0-weapon-light-cd2109-dfs-odg","price":349.99,"options":{"body":"od_green"},"sku":"CD2109-DFS-ODG","in_stock":false,"observed":"2026-11-21","via":"harvest"}],"cmmg-lower-parts-kit":[{"vendor":"cmmg","url":"https://cmmg.com/lower-parts-kit-ar15","price":69.95,"sku":"55CA6C5","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/cmmg-ar-15-lower-parts-kit/","price":64.99,"sku":"3020","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/cmmg-ar-15-lower-parts-kit/","price":64.95,"sku":"3020","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"wing-tactical","url":"https://www.wingtactical.com/firearm-parts/ar-15/lower-receiver-parts/ar-15-lower-receiver-parts-kit/cmmg-ar-15-lower-parts-kit/","price":62.95,"sku":"CMG-55CA6C5","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"alexanders","url":"https://alexandersstore.com/product/cmmg-lpk-556-blk/","price":60.99,"sku":"55CA6C5","in_stock":true,"observed":"2026-11-18","via":"harvest"},{"vendor":"right-to-bear","url":"https://www.righttobear.com/cmmg-ar-15-lower-receiver-parts-kit-lpk-55ca6c5/","price":67.95,"sku":"55CA6C5","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"scheels","url":"https://www.scheels.com/p/lower-parts-kit-for-ar-15/852005-55CA6C5/","price":69.99,"sku":"85200500208","in_stock":true,"observed":"2026-10-05","via":"harvest"},{"vendor":"sportsmans","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/gun-parts-accessories/gun-parts-magazines/rifle-parts/lower-parts/cmmg-ar-15-lower-parts-kit/p/1318758","price":69.99,"sku":"1318758","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"rifle-supply","url":"https://riflesupply.com/CMMG-AR-15-Lower-Parts-Kit-Includes-Trigger-Pistol-Grip-Black-55CA6C5_p_2135.html","price":78.99,"sku":"2135","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"impact-guns","url":"https://www.impactguns.com/ar-15-parts/cmmg-lower-parts-kit-10208-ar-15-standard-852005002080-10208/","price":61.99,"in_stock":true,"observed":"2026-11-21","via":"harvest"}],"cmmg-safety-selector":[{"vendor":"cmmg","url":"https://cmmg.com/safety-selector-ar15","price":11.95,"sku":"55CA741","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The maker's own page; its markup carries CMMG's number."},{"vendor":"sportsmans","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/gun-parts-accessories/gun-parts-magazines/rifle-parts/cmmg-ar15-single-sided-safety-selector-black/p/2001659","price":11.99,"sku":"2001659","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The markup's sku is the seller's own number; its mpn is 55CA741 and its gtin12 815835014791."},{"vendor":"impact-guns","url":"https://www.impactguns.com/AR-15-Parts/CMMG-Safety-Selector-For-AR-15-815835014791-55CA741/","price":16.66,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (\"Manufacturer Number: 55CA741\" in its text, and in its address with the UPC); its offer markup names no number, and says the one price twice."}],"daniel-defense-103-barrel":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/daniel-defense-5-56-10-3-17-chf-barrel-carbine-length-gas-system-07-077-16176-018","price":348,"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (the number 07-077-16176-018 is in its title block and its address); the markup names no number"},{"vendor":"right-to-bear","url":"https://www.righttobear.com/daniel-defense-10-3-5-56-nato-chf-carbine-1-7-government-ar-15-barrel/","price":338,"sku":"07-077-16176-018","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/daniel-defense-10-3-5-56-nato-chf-carbine-length-17-government-contour-ar-15-barrel/","price":327,"sku":"7575","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"7575 is the seller's own number; its page states MPN 07-077-16176-018"},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/daniel-defense-10-3-5-56-nato-chf-carbine-length-17-government-contour-ar-15-barrel/","price":327,"sku":"7575","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"7575 is the seller's own number; its markup carries mpn 07-077-16176-018"},{"vendor":"alexanders","url":"https://alexandersstore.com/product/dd-bbl-556-10-3-gov-car/","price":365,"sku":"07-077-16176-018","in_stock":false,"observed":"2026-11-18","via":"harvest","note":"The markup carries the maker's number as its mpn"},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/2684151347","price":365,"sku":"151347","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of eleven Daniel Defense barrels: 151347 is the seller's number for the 10.3 in Government Contour, whose markup carries 852548002301, the UPC AR15Discounts, Right To Bear and Botach state for 07-077-16176-018"}],"daniel-defense-bcg":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/daniel-defense-m16-cut-complete-bolt-carrier-group-04-013-19032","price":235,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (04-013-19032 is its SKU and MPN and is in its address); its markup (microdata, two offers at one price) names no number"},{"vendor":"wing-tactical","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/ar-15-upper-receiver-parts/bolts-carriers/daniel-defense-5-56-bolt-carrier-group/","price":235,"sku":"DD-556-BCG","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/1016389896","price":247,"sku":"305968","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"impact-guns","url":"https://www.impactguns.com/Other-Parts/Daniel-Defense-Complete-Bolt-Carrier-Group-852548002868-04-013-02146/","price":252.39,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (the UPC 852548002868 is in its address, under Impact's manufacturer number 04-013-02146); its markup (microdata, two offers at one price) names no number"},{"vendor":"rifle-supply","url":"https://riflesupply.com/daniel-defense-complete-bolt-carrier-group-5-56mm-matte-finish-black/","price":247.99,"sku":"DSHIP-DD04-013-19032","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"scheels","url":"https://www.scheels.com/p/daniel-defense-complete-bolt-carrier-group/815604-04-013-19032/","price":228,"sku":"85254800286","in_stock":true,"observed":"2026-10-20","via":"harvest"}],"daniel-defense-fixed-front-sight":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/daniel-defense-rail-mount-fixed-front-sight-19-017-04013","price":77,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of one product whose markup names no number (microdata, $77.00)."},{"vendor":"sportsmans","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/gun-parts-accessories/gun-parts-magazines/gun-sights-lasers/daniel-defense-rail-mounted-fixed-front-sight/p/1865505","price":74.99,"options":{"body":"black"},"sku":"1865505","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"gritr-sports","url":"https://gritrsports.com/daniel-defense-rail-mounted-front-sight-19-017-04013","price":81,"options":{"body":"black"},"sku":"DAN-19-017-04013","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"right-to-bear","url":"https://www.righttobear.com/daniel-defense-rail-mounted-fixed-sight-front-19-017-04013/","price":82,"options":{"body":"black"},"sku":"19-017-04013","in_stock":true,"observed":"2026-11-21","via":"harvest"}],"daniel-defense-fixed-rear-sight":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/daniel-defense-a1-5-fixed-rear-sight-19-064-11002","price":86.6,"options":{"body":"black"},"sku":"19-064-11002","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of one product whose markup names no number (microdata, $105.00)."},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/1003309917","price":110,"options":{"body":"black"},"sku":"181805","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"right-to-bear","url":"https://www.righttobear.com/daniel-defense-rail-mounted-fixed-sight-rear-19-064-11002/","price":105,"options":{"body":"black"},"sku":"19-064-11002","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"alexanders","url":"https://alexandersstore.com/product/dd-a1-5-fixed-rear-sight/","price":110.99,"options":{"body":"black"},"sku":"19-064-11002","in_stock":true,"observed":"2026-11-18","via":"harvest","note":"A page of one product whose markup names no sku (its mpn is 1906411002)."}],"daniel-defense-fixed-sight-set":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/daniel-defense-fixed-rear-iron-sight-combo","price":129.99,"options":{"body":"black"},"sku":"19-088-09116","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of one product whose markup names no number (microdata, $149.00)."},{"vendor":"wing-tactical","url":"https://www.wingtactical.com/accessories/optics-sights/sights/daniel-defense-ar-15-fixed-iron-sights/","price":149,"options":{"body":"black"},"sku":"DD-19-088-09116","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"rifle-supply","url":"https://riflesupply.com/Daniel-Defense-Fixed-FrontRear-Iron-Sight-Combo-AR15-Picatinny-Black-19-088-09116_p_4974.html","price":155.99,"options":{"body":"black"},"sku":"4974","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"gritr","url":"https://gritroutdoors.com/daniel-defense-fixed-front-rear-sights-19-088-09116-012","price":173,"options":{"body":"tornado"},"sku":"DAN-19-088-09116-012","in_stock":true,"observed":"2026-11-21","via":"harvest"}],"dead-air-rxd22ti-kit":[{"vendor":"kygunco","url":"https://www.kygunco.com/product/dead-air-rxd22ti-22-cal-black-w-rxd674-xrf-muzzle-brake","price":438.99,"options":{"body":"black"},"sku":"285569","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"KYGUNCO's own number; its markup's MPN is RXD22TIBLK"},{"vendor":"kygunco","url":"https://www.kygunco.com/product/dead-air-rxd22ti-22-cal-bronze-w-rxd674-xrf-muzzle-brake","price":438.99,"options":{"body":"burnt_bronze"},"sku":"285570","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"KYGUNCO's own number; its markup's MPN is RXD22TiBB"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/rxd22tiblk","price":469,"options":{"body":"black"},"sku":"RXD22TIBLK","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"silencer-shop","url":"https://silencershop.com/dead-air-rxd22ti.html","price":469,"sku":"DA RDX22Ti-MULTI","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"One price for either colour, chosen on the page; its markup's number is its own (DA RDX22Ti-MULTI)"}],"dead-air-xrf-brake":[{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/rxd674","price":67,"sku":"RXD674","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"kygunco","url":"https://www.kygunco.com/product/dead-air-xrf-rimfire-muzzle-brake-1-2x28","price":52.9,"sku":"298561","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"KYGUNCO's own number; its markup's MPN is RXD674"}],"eotech-exps3":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/eotech-exps3-0-holographic-weapon-sight","price":815,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The page names it: SKU EXPS3-0, MPN EXPS3-0. Its offer markup names no number."},{"vendor":"right-to-bear","url":"https://www.righttobear.com/eotech-model-exps3-0-holographic-sight-exps3-0/","price":815,"options":{"body":"black"},"sku":"EXPS3-0","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"scheels","url":"https://www.scheels.com/p/eotech-exps3-holographic-sight-with-1-moa-dot-reticle/5878-EXPS3-0","price":815,"options":{"body":"black"},"sku":"67229460033","in_stock":true,"observed":"2026-10-06","via":"harvest","note":"Scheels' own number is in the page's address (5878-EXPS3-0); its reticle field is the 68 MOA ring and 1 MOA dot."},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/eotech-exps3-0/","price":652,"options":{"body":"black"},"sku":"111307","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"A series page (EXPS3-0 and EXPS3-1, black and tan): T.REX's own number for the black EXPS3-0, which its markup carries."},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/1868161365/","price":815,"options":{"body":"black"},"sku":"161365","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"MidwayUSA's product 1868161365, 'EOTech EXPS3-0 Holographic Weapon Sight 68 MOA Circle 1 MOA Dot': it lists black and tan under one product; the black one's number wasn't read."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/eotech-exps3-0-holographic-weapon-sight-tan","price":815,"options":{"body":"tan"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The page names it: SKU EXPS3-0TAN, MPN EXPS3-0 TAN. Its offer markup names no number."},{"vendor":"right-to-bear","url":"https://www.righttobear.com/eotech-model-exps3-0-holographic-sight-tan-rds-eoexps3-0tan/","price":819,"options":{"body":"tan"},"sku":"EXPS3-0TAN","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/eotech-exps3-0/","price":611.25,"options":{"body":"tan"},"sku":"111308","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The same series page: T.REX's own number for the tan EXPS3-0 (\"EOTECH HWS EXPS3 Series - 1 MOA Dot w/ 68 MOA Bullseye (EXPS3-0), Tan\"), which its markup carries."}],"eotech-g33":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/eotech-g33-gen-iii-magnifier-w-sts-mount-black-g33-sts","price":645,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/eotech-g33-3x-magnifier-73466","price":548.25,"options":{"body":"black"},"sku":"111294","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"sportsmans","url":"https://www.sportsmans.com/hunting-gear-supplies/optics-binoculars-scopes-rangefinders/red-dots/eotech-g33-3x-magnifier/p/1294943","price":516,"options":{"body":"black"},"sku":"1294943","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"kygunco","url":"https://www.kygunco.com/product/eotech-g33.sts-holographic-hybrid-sight-g33","price":527.68,"options":{"body":"black"},"sku":"48736","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"impact-guns","url":"https://www.impactguns.com/reflex-sights/eotech-g33-magnifier-w-slap-to-side-mount-black-672294300380-g33-sts/","price":679,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"rifle-supply","url":"https://riflesupply.com/Eotech-G33-3x-Magnifer-w-Switch-To-Side-Mount-Black-G33STS_p_2028.html","price":663.99,"options":{"body":"black"},"sku":"2028","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/eotech-3-power-magnifier-with-sts-switch-to-side-mount-works-with-existing-hws-units-blk/","price":489,"options":{"body":"black"},"sku":"31675","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/eotech-g33-gen-iii-magnifier-w-sts-mount-tan-g33-ststan","price":645,"options":{"body":"tan"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Primary Arms' page for the tan kit (its address ends g33-ststan); its offer markup names no number."},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/eotech-g33-3x-magnifier-73466","price":516,"options":{"body":"tan"},"sku":"111295","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The same page as the black kit's: T.REX's own number for \"EOTECH G33 3x Magnifier - Tan\", which its markup carries."},{"vendor":"sportsmans","url":"https://www.sportsmans.com/hunting-gear-supplies/optics-binoculars-scopes-rangefinders/red-dots/eotech-g33sts-3x-red-dot-magnifier/p/1751061","price":645,"options":{"body":"tan"},"sku":"1751061","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Sportsman's own number, which its markup carries with the maker's as \"G33.STS TAN\"."}],"eotech-g45":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/eotech-g45-5x-magnifier-black","price":609.99,"options":{"body":"black"},"sku":"G45.STS","in_stock":true,"observed":"2026-10-29","via":"harvest"},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/eotech-g45-5x-magnifier-652617","price":607.75,"options":{"body":"black"},"sku":"921694","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"T.REX's own number for \"EOTECH G45 5x Magnifier - Black\", which its markup carries."},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/eotech-g45-5x-magnifier-652617","price":572,"options":{"body":"tan"},"sku":"921695","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The same page as the black kit's: T.REX's own number for \"EOTECH G45 5x Magnifier - Tan\"."},{"vendor":"silencer-shop","url":"https://www.silencershop.com/eotech-g45.html","price":715,"options":{"body":"black"},"sku":"EO-G45.STS","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"The page's title names no colour; its number is the black kit's (G45.STS) with the shop's prefix."},{"vendor":"impact-guns","url":"https://www.impactguns.com/reflex-sights/eotech-g45-magnifier-5x-magnification-monocular-quick-detach-mount-black-672294300465-g45-sts","price":755,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of the one product (its address and title name the black kit, G45.STS); its offer markup names no number, and states the one price twice."},{"vendor":"rifle-supply","url":"https://riflesupply.com/EOTech-G45-5X-Magnifier-QD-Mount-Switch-to-Side-Black-Finish-34mm-G45STS_p_6677.html","price":732.99,"options":{"body":"black"},"sku":"6677","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Rifle Supply's own item number, which its markup carries with the maker's as G45.STS."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/eotech-5-power-magnifier-w-quick-disconnect-switch-to-side-sts-mount-black/","price":679,"options":{"body":"black"},"sku":"31678","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"kygunco","url":"https://www.kygunco.com/product/eotech-g45.ststan-5-power-magnifer-with-qd-sts-mount-tan","price":604.04,"options":{"body":"tan"},"sku":"231234","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"KYGunCo's own item number, which its markup carries with the maker's as G45.STSTAN. Its listing picture is the tan magnifier alone; the page is the kit's."},{"vendor":"gritr-sports","url":"https://gritrsports.com/eotech-g45-sts-tan-mini-5x-magnifier-g45-ststan","price":643.5,"options":{"body":"tan"},"sku":"EOT-G45.STSTAN","in_stock":true,"observed":"2026-11-21","via":"harvest"}],"expo-arms-mlok-15-handguard":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/expo-arms-m-lok-handguard-black-15","price":99.99,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (the number is in its title and its address); the markup names no number"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/expo-arms-15-m-lok-handguard-flat-dark-earth-xp-guard15-fde","price":119.99,"options":{"body":"fde"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product in FDE (XP-GUARD15-FDE, in its address); the markup names no number (two offers, one price: checked 2026-10-06)"}],"expo-arms-stripped-upper":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/expo-arms-ar-15-7075-stripped-upper-receiver","price":49.99,"options":{"receiver":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (the number is in its title and its address); the markup names no number"}],"faxon-16-pencil-barrel":[{"vendor":"faxon","url":"https://faxonfirearms.com/15A58M16NPQ","price":187,"sku":"15A58M16NPQ","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/faxon-firearms-5-56-ar-15-barrel-mid-length-pencil-16","price":154.99,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (SKU and MPN 15A58M16NPQ in its text); the markup names no number"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/15a58m16npq","price":173,"sku":"15A58M16NPQ","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"right-to-bear","url":"https://www.righttobear.com/faxon-firearms-16-pencil-5-56-nato-mid-length-15a58m16npq/","price":187,"sku":"15A58M16NPQ","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"impact-guns","url":"https://www.impactguns.com/Barrels/Faxon-Barrel-16-Pencil-5-56-Nato-Mid-Length-4150-Qpq-816341020146-15A58M16NPQ/","price":173,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (the maker's number and the UPC are in its address); the markup names no number"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/faxon-firearms-16-pencil-5-56-nato-mid-length-4150-nitride-melonite-barrel/","price":149.95,"sku":"2191","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The markup's number is the seller's own; the page's title names 15A58M16NPQ"}],"fn-p90-50-magazine":[{"vendor":"kygunco","url":"https://www.kygunco.com/product/fnh-usa-3810110093-ps90-5.7x28-50rd-smoke-finish-magazine","price":36.99,"options":{"body":"smoke"},"sku":"50648","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"KYGUNCO's own item number; its markup's mpn is FN's 3810110093."},{"vendor":"midwest-gun-works","url":"https://midwestgunworks.com/page/mgwi/prod/3810110093","price":44.99,"options":{"body":"smoke"},"sku":"3810110093","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Listed as \"Finish / Color: Black\" over a photo of the smoke one (128e601bf5c7): FN's one 50-round magazine."}],"geissele-139-chf-barrel":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/geissele-automatics-5-56-chf-mid-length-taper-profile-ar-15-barrel-chrome-lined-13-9in","price":365,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (SKU and MPN 05-2989 in its text); the markup names no number"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/geissele-5-56-nato-13-9-17-midlength-cold-hammer-forged-chrome-lined-barrel/","price":365,"sku":"16938","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The markup's number is the seller's own; the page states MPN 05-2989 and UPC 810081134958"},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/geissele-5-56-nato-13-9-17-midlength-cold-hammer-forged-chrome-lined-barrel/","price":365,"sku":"16938","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The markup's sku is the seller's own (its mpn is 05-2989)"}],"geissele-145-chf-barrel":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/geissele-automatics-5-56-chf-mid-length-taper-profile-ar-15-barrel-chrome-lined-14-5in","price":365,"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (SKU and MPN 05-2985 in its text); the markup names no number"},{"vendor":"mile-high","url":"https://www.milehighshooting.com/geissele-chf-chrome-lined-barrel-5-56-14-5/","price":365,"sku":"05-2985","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/geissele-automatics-chf-5-56-14-5-chrome-lined-barrel/","price":365,"sku":"13290","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The markup's number is the seller's own; the page's title prints the maker's as 05-2895 (sic) and its UPC is 810081134910, as Primary Arms' feed has for 05-2985"}],"geissele-16-chf-barrel":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/geissele-automatics-5-56-chf-chrome-lined-ar-15-barrel-mid-length-taper-profile-16in","price":365,"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (SKU and MPN 05-2984 in its text); the markup names no number (two offers, one price)"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/geissele-automatics-16-chf-government-phosphate-17-midlengtrh-barrel/","price":365,"sku":"13291","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The markup's number is the seller's own; the page states MPN 05-2984 and UPC 810081134903"}],"geissele-mk16-105-handguard":[{"vendor":"aerospace-arms","url":"https://aerospacearms.com/geissele-automatics-10-5-super-modular-rail-mk16-m-lok-black/","price":325,"options":{"body":"black"},"sku":"GEI05-1073B","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The seller's own number, which the markup carries, with the maker's as mpn (05-1073B)"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/geissele-automatics-super-modular-rail-mk16-m-lok-black-10.5in","price":325,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (SKU and MPN 05-1073B on the page); its offer markup names no number (make offers show, 2026-10-06)"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/geissele-automatics-super-modular-rail-mk16-m-lok-ddc-10.5in","price":350,"options":{"body":"ddc"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (SKU and MPN 05-1073S on the page); its offer markup names no number (make offers show, 2026-10-06)"},{"vendor":"aerospace-arms","url":"https://aerospacearms.com/geissele-automatics-10-5-super-modular-rail-mk16-m-lok-ddc/","price":350,"options":{"body":"ddc"},"sku":"GEI05-1073S","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The seller's own number, which the markup carries, with the maker's as mpn (05-1073S)"},{"vendor":"rifle-supply","url":"https://riflesupply.com/geissele-10-5-smr-mk16-mlok-ddc/","price":350.99,"options":{"body":"ddc"},"sku":"DSHIP-GEI05-1073S","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The seller's own number, which the markup carries, with the maker's as mpn (05-1073S)"}],"geissele-mk16-135-handguard":[{"vendor":"aerospace-arms","url":"https://aerospacearms.com/geissele-automatics-13-5-super-modular-rail-mk16-m-lok-black/","price":350,"options":{"body":"black"},"sku":"GEI05-650B","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The seller's own number, which the markup carries, with the maker's as mpn (05-650B)"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/geissele-automatics-mk16-super-modular-m-lok-rail-black-13.5","price":350,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (SKU and MPN 05-650B on the page); its offer markup names no number (make offers show, 2026-10-06)"},{"vendor":"rifle-supply","url":"https://riflesupply.com/geissele-13-5-smr-mk16-mlok-blk/","price":350.99,"options":{"body":"black"},"sku":"DSHIP-GEI05-650B","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/geissele-automatics-13.5-in-super-modular-rail-m-lok-ddc","price":375,"options":{"body":"ddc"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (SKU and MPN 05-650S on the page); its offer markup names no number (make offers show, 2026-10-06)"},{"vendor":"aerospace-arms","url":"https://aerospacearms.com/geissele-automatics-13-5-super-modular-rail-mk16-m-lok-ddc/","price":375,"options":{"body":"ddc"},"sku":"GEI05-650S","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The seller's own number, which the markup carries, with the maker's as mpn (05-650S)"},{"vendor":"sportsmans","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/gun-parts-magazines/rifle-parts/rails-handguards/geissele-super-modular-mk16-m-lok-135in-rail-desert-dirt-color/p/1628406","price":228.92,"options":{"body":"ddc"},"sku":"1628406","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The seller's own number, which the markup carries, with the maker's as mpn (05-650S)"}],"geissele-mk16-15-handguard":[{"vendor":"mile-high","url":"https://www.milehighshooting.com/geissele-15-super-modular-rail-mk16-m-lok/","price":375,"options":{"body":"black"},"sku":"05-792B","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/geissele-automatics-super-modular-rail-mk16-m-lok-black-15in","price":375,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (SKU and MPN 05-792B on the page); its offer markup names no number (make offers show, 2026-10-06)"},{"vendor":"rifle-supply","url":"https://riflesupply.com/geissele-15-smr-mk16-mlok-blk/","price":375.99,"options":{"body":"black"},"sku":"DSHIP-GEI05-792B","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"gritr-sports","url":"https://gritrsports.com/geissele-automatics-15-super-modular-rail-mk16-m-lok-05-792b","price":301.77,"options":{"body":"black"},"sku":"GEIS-05-792B","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/geissele-automatics-super-modular-rail-mk16-mlok-ddc-15in","price":400,"options":{"body":"ddc"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (SKU and MPN 05-792S on the page); its offer markup names no number (make offers show, 2026-10-06)"},{"vendor":"aerospace-arms","url":"https://aerospacearms.com/geissele-automatics-15-super-modular-rail-mk16-m-lok-ddc/","price":400,"options":{"body":"ddc"},"sku":"GEI05-792S","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The seller's own number, which the markup carries, with the maker's as mpn (05-792S)"}],"geissele-premium-mil-spec-buffer-tube-assembly-super-42-h1":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/geissele-automatics-premium-mil-spec-buffer-tube-assembly-with-h1-buffer-and-super-42-spring_2","price":133,"options":{"tube":"black"},"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (SKU 08-163B, MPN 08-163B in its text); its offer markup names no number (make offers show, 2026-11-03: two offers, one price)."}],"geissele-premium-mil-spec-buffer-tube-assembly-super-42-h2":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/geissele-automatics-premium-mil-spec-buffer-tube-assembly-super-42-h2-ddc","price":172,"options":{"tube":"ddc"},"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (SKU 08-163S-H2, MPN 08-163S-H2 in its text); its offer markup names no number (make offers show, 2026-11-03: two offers, one price)."}],"geissele-premium-mil-spec-buffer-tube-assembly":[{"vendor":"charlies-custom-clones","url":"https://charliescustomclones.com/geissele-premium-mil-spec-buffer-tube-assembly-gray/","price":119,"options":{"tube":"gray"},"sku":"08-162G","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its markup's offer carries mpn 08-162G (no sku); the page shows its own SKU G081637."},{"vendor":"charlies-custom-clones","url":"https://charliescustomclones.com/geissele-premium-mil-spec-buffer-tube-assembly-desert-dirt-ddc/","price":72,"options":{"tube":"ddc"},"sku":"08-162S","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Its markup's offer carries mpn 08-162S (no sku); the page shows its own SKU G081621. Out of stock when read."},{"vendor":"mile-high","url":"https://www.milehighshooting.com/geissele-premium-mil-spec-buffer-tube/","price":68,"options":{"tube":"black"},"sku":"08-162B","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/geissele-automatics-premium-mil-spec-ar15-buffer-tube-black","price":68,"options":{"tube":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (SKU 08-162B, MPN 08-162B in its text); its offer markup names no number (make offers show, 2026-11-03: two offers, one price). Out of stock when read."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/geissele-automatics-premium-mil-spec-ar15-buffer-tube-desert-dirt","price":80,"options":{"tube":"ddc"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (SKU 08-162S, MPN 08-162S in its text); its offer markup names no number (make offers show, 2026-11-03: two offers, one price)."}],"geissele-ssa-e":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/geissele-automatics-super-semi-automatic-enhanced-ssa-e-two-stage-ar-15-trigger-.154in","price":250,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The page's text gives SKU GATSSA-E and MPN 05-160; its offer markup names no number."},{"vendor":"mile-high","url":"https://www.milehighshooting.com/geissele-super-semi-automatic-enhanced-ssa-e-trigger/","price":250,"sku":"05-160","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"bcm","url":"https://bravocompanyusa.com/geissele-ar15-super-semi-automatic-enhanced-trigger-small-pin/","price":240,"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (BCM's own number for it is GEISSELE-SSA-E); its offer markup names no number."},{"vendor":"right-to-bear","url":"https://www.righttobear.com/geissele-super-semi-automatic-enhanced-ssa-e-ssa-e/","price":245,"sku":"SSA-E","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Seller's number SSA-E, UPC 854014005038 on the page."},{"vendor":"gritr-sports","url":"https://gritrsports.com/geissele-semi-auto-enhanced-3-5lb-trigger-05-160","price":240,"sku":"GEIS-05-160","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The seller's own number, which the markup carries (the page's markup also holds another product's offer)."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/geissele-super-semi-automatic-enhanced-ssa-e-trigger/","price":250,"sku":"1959","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"MPN 05-160, UPC 854014005038 on the page; the markup carries the seller's own number."},{"vendor":"silencer-shop","url":"https://www.silencershop.com/geissele-super-semi-automatic-enhanced-trigger-ssa-e.html","price":250,"sku":"GEISSELE-05-160","in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"kygunco","url":"https://www.kygunco.com/product/geissele-ssa-e-super-semi-auto-enhanced-trigg","price":213.01,"sku":"52073","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/geissele-super-semi-automatic-enhanced-trigger","price":245,"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (Aero's number for it is APRH100363); its offer markup names no number."}],"geissele-super-42-h1":[{"vendor":"mile-high","url":"https://www.milehighshooting.com/geissele-super-42-braided-wire-buffer-spring-and-buffer-combo-h1/","price":85,"sku":"05-495","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/geissele-automatics-super-42-braided-buffer-spring-and-buffer","price":85,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (SKU GAT05-495, MPN 05-495 in its text); its offer markup names no number (make offers show, 2026-10-12)."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/05-495","price":85,"sku":"05-495","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/1017901689","price":85,"sku":"104024","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One page for the three combos; 104024 is MidwayUSA's own number for the H1 in its markup (its data: sku 05-495, upc 854014005908)."},{"vendor":"impact-guns","url":"https://www.impactguns.com/ar-15-lower-receiver-parts/geissele-automatics-super-42-braided-wire-buffer-and-spring-combo-not-compatible-with-rifle-length-or-a5-buffer-tubes-receiver-extensions-fits-ar15-854014005908-05-495","price":79.29,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (Manufacturer Number 05-495; its address ends in the UPC and the number); its offer markup names no number."},{"vendor":"gritr-sports","url":"https://gritrsports.com/geissele-super-42-braided-wire-spring-buffer-05-495","price":71.99,"sku":"GEIS-05-495","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The seller's own number, which the markup carries with mpn 05-495 (the page's markup also holds another product's offer)."},{"vendor":"alexanders","url":"https://alexandersstore.com/product/geissele-spr-42-brd-wire-bfr-spr-cmb/","price":85,"sku":"05-495","in_stock":true,"observed":"2026-11-18","via":"harvest","note":"The markup carries the number as mpn."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/geissele-super-42-braided-wire-buffer-spring-and-buffer-combo/","price":75,"sku":"1981","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The seller's own number, which the markup carries; MPN 05-495, UPC 854014005908 on the page."}],"geissele-super-42-h2":[{"vendor":"mile-high","url":"https://www.milehighshooting.com/geissele-super-42-braided-wire-buffer-spring-and-buffer-combo-h2/","price":114,"sku":"05-495-H2","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/geissele-automatics-super-42-braided-buffer-spring-and-h2-buffer","price":114,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (SKU and MPN 05-495-H2 in its text); its offer markup names no number (make offers show, 2026-10-12)."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/05-495-h2","price":114,"sku":"05-495-H2","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/1017901689","price":114,"sku":"734974","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One page for the three combos; 734974 is MidwayUSA's own number for the H2 in its markup (its data: sku 05-495-H2, upc 817953026915)."},{"vendor":"impact-guns","url":"https://www.impactguns.com/ar-15-lower-receiver-parts/geissele-automatics-super-42-kit-h2-buffer-braided-wire-buffer-spring-combo-fits-ar-15-817953026915-05495h2","price":114,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (Manufacturer Part # 05-495-H2; its address ends in the UPC and the number); its offer markup names no number."},{"vendor":"gritr-sports","url":"https://gritrsports.com/geissele-automatics-super-42-combo-set-05-495-h2","price":95.99,"sku":"GEIS-05-495-H2","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The seller's own number, which the markup carries with mpn 05-495-H2 (the page's markup also holds another product's offer)."},{"vendor":"rifle-supply","url":"https://riflesupply.com/geissele-spr-42-brd-wire-bfr-spr-h2/","price":114.99,"sku":"DSHIP-GEI05-495-H2","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The seller's own number, with mpn 05-495-H2."}],"geissele-super-42-h3":[{"vendor":"mile-high","url":"https://www.milehighshooting.com/geissele-super-42-braided-wire-buffer-spring-and-buffer-combo-h3/","price":142,"sku":"05-495-H3","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/geissele-automatics-super-42-braided-buffer-spring-and-h3-buffer","price":142,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (SKU and MPN 05-495-H3 in its text); its offer markup names no number (make offers show, 2026-10-12)."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/05-495-h3","price":142,"sku":"05-495-H3","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/1017901689","price":142,"sku":"826469","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One page for the three combos; 826469 is MidwayUSA's own number for the H3 in its markup (its data: sku 05-495-H3, upc 817953026922)."},{"vendor":"impact-guns","url":"https://www.impactguns.com/ar-15-lower-receiver-parts/geissele-automatics-super-42-kit-h3-buffer-and-braided-wire-buffer-spring-combo-fits-ar-15-817953026922-05-495-h3","price":126.99,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (Manufacturer Part # 05-495-H3; its address ends in the UPC and the number); its offer markup names no number."},{"vendor":"gritr-sports","url":"https://gritrsports.com/geissele-automatics-buffer-spring-h3-buffer-05-495-h3","price":119.99,"sku":"GEIS-05-495-H3","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The seller's own number, which the markup carries with mpn 05-495-H3 (the page's markup also holds another product's offer)."},{"vendor":"rifle-supply","url":"https://riflesupply.com/geissele-spr-42-brd-wire-bfr-spr-h3/","price":142.99,"sku":"DSHIP-GEI05-495-H3","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The seller's own number, with mpn 05-495-H3. Out of stock on 2026-10-12."},{"vendor":"alexanders","url":"https://alexandersstore.com/product/geissele-spr-42-brd-wire-bfr-spr-h3/","price":142,"sku":"05-495-H3","in_stock":true,"observed":"2026-11-18","via":"harvest","note":"The markup carries the number as mpn, written 05495H3."},{"vendor":"kygunco","url":"https://www.kygunco.com/product/geissele-super-42-braided-wire-buffer-spring-buffr-combo-h3","price":130.99,"sku":"278374","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The seller's item number, which the markup carries with mpn 05-495-H3."}],"geissele-super-duty-receiver-set":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/geissele-automatics-super-duty-stripped-ar15-receiver-set-black","price":350,"options":{"receiver":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The black set, 05-1171B by the upper's owner's reading of the page; its markup names no number (two microdata offers, one price)."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/geissele-automatics-super-duty-stripped-ar-15-receiver-set-ddc","price":400,"options":{"receiver":"ddc"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The Desert Dirt Color set, 05-1171S; its markup names no number (two microdata offers, one price)."}],"geissele-super-duty-stripped-lower":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/geissele-automatics-super-duty-stripped-ar-15-lower-stripped-lower","price":175,"options":{"receiver":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Primary Arms' page for 05-2994-B (its title and 'SKU: 05-2994-B' in the page's text): its markup names no number."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/geissele-automatics-super-duty-stripped-lower-ddc-stripped-lower","price":200,"options":{"receiver":"ddc"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Primary Arms' page for 05-2994-S, the Desert Dirt lower ('SKU: 05-2994-S' in the page's text): its markup names no number."}],"geissele-super-precision-micro-193":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/geissele-automatics-super-precision-aimpoint-t2-mount-1.93in-black","price":150,"options":{"body":"black"},"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"One product, black (the page: \"SKU: 05-543B\"); its markup's offer names no number."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/geissele-automatics-super-precision-aimpoint-t2-mount-1.93in-desert-dirt","price":160,"options":{"body":"ddc"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One product, Desert Dirt (05-543S); its markup's offer names no number."},{"vendor":"kygunco","url":"https://www.kygunco.com/product/geissele-super-precision-mount-aimpoint-t1-t1-black","price":138.06,"options":{"body":"black"},"sku":"256290","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its markup: sku 256290, mpn 05-543B."}],"geissele-super-precision-micro-absolute":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/geissele-super-precision-aimpoint-t1-compatible-optic-mount-absolute-cowitness-black-05-401b","price":150,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One product, black (the page: \"SKU: 05-401B MPN: 05-401B\"); its markup's offer names no number."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/geissele-super-precision-aimpoint-t1-compatible-optic-mount-absolute-cowitness-desert-dirt-null","price":160,"options":{"body":"ddc"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One product, Desert Dirt (the page: \"SKU: 05-401S MPN: 05-401S\"); its markup's offer names no number."},{"vendor":"sportsmans","url":"https://www.sportsmans.com/hunting-gear-supplies/optics-binoculars-scopes-rangefinders/scope-rings-bases/geissele-super-precision-t1-mount-absolute-co-witness-black-matte-black/p/1787278","price":145.99,"options":{"body":"black"},"sku":"1787278","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Its markup: sku 1787278, mpn 05-401B."},{"vendor":"rifle-supply","url":"https://riflesupply.com/geissele-spr-prcsn-t1-co-wit-ddc/","price":155.99,"options":{"body":"ddc"},"sku":"DSHIP-GEI05-401S","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Its markup: sku DSHIP-GEI05-401S, mpn 05-401S."}],"geissele-super-precision-micro-lower-13":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/geissele-super-precision-aimpoint-t1-compatible-optic-mount-lower-1-3-cowitness","price":150,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One product, black (the page: \"SKU: 05-469B\"); its markup's offer names no number."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/geissele-super-precision-aimpoint-t1-compatible-optic-mount-lower-1-3-cowitness-desert-dirt","price":160,"options":{"body":"ddc"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One product, Desert Dirt (05-469S); its markup's offer names no number."},{"vendor":"kygunco","url":"https://www.kygunco.com/product/geissele-super-precision-mount-aimpoint-t1-lower-black","price":131.04,"options":{"body":"black"},"sku":"256286","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its markup: sku 256286, mpn 05-469B."}],"guntec-ar15-carbine-buffer":[{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/carbuf","price":19.95,"sku":"CARBUF","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"guntec-usa","url":"https://guntecusa.com/product/ar-15-mil-spec-car-buffer/","price":19.95,"sku":"CARBUF","in_stock":true,"observed":"2026-10-20","via":"user","note":"Guntec's own page, as the user saved it from their browser on 2026-10-20: the site refuses the reader and is never asked (D59). Its markup states the price (product:price:amount 19.95); the page shows SKU CARBUF."}],"guntec-ar15-castle-nut":[{"vendor":"cheaper-than-dirt","url":"https://www.cheaperthandirt.com/guntec-ar-15-castle-nut-for-carm4-buffer-tube-steel-black-finish/FC-714569643782.html","price":7.89,"sku":"CASTLE","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The page's markup names no number (its mpn is CASTLE, Guntec's)."},{"vendor":"tactical-transition","url":"https://tacticaltransition.com/product/ar-15-castle-nut-for-carm4-buffer-tube/","price":7.95,"sku":"CASTLE","in_stock":true,"observed":"2026-11-21","via":"harvest"}],"guntec-ar15-end-plate":[{"vendor":"guntec-usa","url":"https://guntecusa.com/product/ar-15-receiver-end-plate/","price":5.95,"sku":"ENDPLATE","in_stock":true,"observed":"2026-10-20","via":"user","note":"Guntec's own page, as the user saved it from their browser on 2026-10-20: the site refuses the reader and is never asked (D59). The page shows SKU ENDPLATE, UPC 714569652319."}],"guntec-ar15-heavy-duty-castle-nut":[{"vendor":"guntec-usa","url":"https://guntecusa.com/product/ar15-heavy-duty-wide-castle-nut-for-car-m4-buffer-tube/","price":8.95,"sku":"CASTLE-HD","in_stock":true,"observed":"2026-10-20","via":"user","note":"Guntec's own page, as the user saved it from their browser on 2026-10-20: the site refuses the reader and is never asked (D59). The page shows SKU CASTLE-HD, UPC 714569647827."}],"guntec-ar15-mil-spec-buffer-tube-gen-2":[{"vendor":"the2ndtactical","url":"https://the2ndtactical.com/guntec-ar-15-ar-10-mil-spec-buffer-tube-anodized-clear.html","price":34.99,"options":{"tube":"clear"},"sku":"GT-BT-CLEAR ANO","in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"the2ndtactical","url":"https://the2ndtactical.com/ar-15-ar-10-mil-spec-buffer-tube-red-anodized.html","price":34.99,"options":{"tube":"red"},"sku":"GT-BT-RED ANO","in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"the2ndtactical","url":"https://the2ndtactical.com/guntec-ar-15-ar-10-mil-spec-buffer-tube-anodized-gold.html","price":34.99,"options":{"tube":"gold"},"sku":"GT-BT-GOLD ANO","in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"the2ndtactical","url":"https://the2ndtactical.com/guntec-ar-15-ar-10-mil-spec-buffer-tube-blue-anodized.html","price":34.99,"options":{"tube":"blue"},"sku":"GT-BT-BLUE ANO","in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"the2ndtactical","url":"https://the2ndtactical.com/guntec-ar-15-ar-10-mil-spec-buffer-tube-purple-anodized.html","price":34.99,"options":{"tube":"purple"},"sku":"GT-BT-PURPLE ANO","in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"the2ndtactical","url":"https://the2ndtactical.com/guntec-ar-15-ar-10-mil-spec-buffer-tube-anodized-green.html","price":34.99,"options":{"tube":"green"},"sku":"GT-BT-GREEN ANO","in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"the2ndtactical","url":"https://the2ndtactical.com/guntec-ar-15-ar-10-mil-spec-buffer-tube-anodized-irish-green.html","price":34.99,"options":{"tube":"irish-green"},"sku":"GT-BT-IG","in_stock":null,"observed":"2026-11-21","via":"harvest"}],"guntec-ar15-mil-spec-buffer-tube-set":[{"vendor":"guntec-usa","url":"https://guntecusa.com/product/ar-15-mil-spec-buffer-tube-set-anodized-clear/","price":59.95,"options":{"tube":"clear"},"sku":"MILTUBESET-CLEAR","in_stock":true,"observed":"2026-10-20","via":"user"},{"vendor":"guntec-usa","url":"https://guntecusa.com/product/ar-15-mil-spec-buffer-tube-set-anodized-blue/","price":59.95,"options":{"tube":"blue"},"sku":"MILTUBESET-BLUE","in_stock":true,"observed":"2026-10-20","via":"user"},{"vendor":"guntec-usa","url":"https://guntecusa.com/product/ar-15-mil-spec-buffer-tube-set-anodized-grey/","price":59.95,"options":{"tube":"grey"},"sku":"MILTUBESET-GREY","in_stock":true,"observed":"2026-10-20","via":"user"},{"vendor":"guntec-usa","url":"https://guntecusa.com/product/ar-15-mil-spec-buffer-tube-set-anodized-irish-green/","price":59.95,"options":{"tube":"irish-green"},"sku":"MILTUBESET-IG","in_stock":true,"observed":"2026-10-20","via":"user"},{"vendor":"guntec-usa","url":"https://guntecusa.com/product/ar-15-mil-spec-buffer-tube-set-anodized-orange/","price":59.95,"options":{"tube":"orange"},"sku":"MILTUBESET-ORANGE","in_stock":true,"observed":"2026-10-20","via":"user"},{"vendor":"guntec-usa","url":"https://guntecusa.com/product/ar-15-mil-spec-buffer-tube-set-anodized-pink/","price":59.95,"options":{"tube":"pink"},"sku":"MILTUBESET-PINK","in_stock":true,"observed":"2026-10-20","via":"user"},{"vendor":"redcon1","url":"https://redcon1tactical.com/guntec-usa-ar-15-mil-spec-buffer-tube-kit-anodized-clear.html","price":54.95,"options":{"tube":"clear"},"sku":"MILTUBESET-CLEAR","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The page's markup names no sku: its mpn is MILTUBESET-CLEAR, Guntec's number for this colour."},{"vendor":"redcon1","url":"https://redcon1tactical.com/guntec-usa-ar-15-mil-spec-buffer-tube-kit-anodized-red.html","price":54.95,"options":{"tube":"red"},"sku":"MILTUBESET-RED","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The page's markup names no sku: its mpn is MILTUBESET-RED, Guntec's number for this colour."},{"vendor":"redcon1","url":"https://redcon1tactical.com/guntec-usa-ar-15-mil-spec-buffer-tube-kit-anodized-blue.html","price":54.95,"options":{"tube":"blue"},"sku":"MILTUBESET-BLUE","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The page's markup names no sku: its mpn is MILTUBESET-BLUE, Guntec's number for this colour."},{"vendor":"redcon1","url":"https://redcon1tactical.com/guntec-usa-ar-15-mil-spec-buffer-tube-kit-anodized-gold.html","price":54.95,"options":{"tube":"gold"},"sku":"MILTUBESET-GOLD","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The page's markup names no sku: its mpn is MILTUBESET-GOLD, Guntec's number for this colour."},{"vendor":"redcon1","url":"https://redcon1tactical.com/guntec-usa-ar-15-mil-spec-buffer-tube-kit-anodized-purple.html","price":54.95,"options":{"tube":"purple"},"sku":"MILTUBESET-PURPLE","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The page's markup names no sku: its mpn is MILTUBESET-PURPLE, Guntec's number for this colour."},{"vendor":"abc-sportz","url":"https://abcsportz.com/guntec-usa-miltubeset-clear-mil-spec-buffer-tube-set-anodized-clear/","price":46.2,"options":{"tube":"clear"},"sku":"MILTUBESET-CLEAR","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"abc-sportz","url":"https://abcsportz.com/guntec-usa-miltubeset-gold-mil-spec-buffer-tube-set-anodized-gold/","price":46.2,"options":{"tube":"gold"},"sku":"MILTUBESET-GOLD","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"abc-sportz","url":"https://abcsportz.com/guntec-usa-miltubeset-green-mil-spec-buffer-tube-set-anodized-green/","price":46.2,"options":{"tube":"green"},"sku":"MILTUBESET-GREEN","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"the-country-shed","url":"https://www.thecountryshed.com/GunTec-AR-15-Mil-Spec-Buffer-Tube-Set--Red_p_3709.html","price":50,"options":{"tube":"red"},"sku":"MILTUBESET-RED","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/miltubeset","price":52.5,"options":{"tube":"black"},"sku":"MILTUBESET","in_stock":true,"observed":"2026-11-21","via":"harvest"}],"guntec-ar15-stainless-carbine-buffer":[{"vendor":"guntec-usa","url":"https://guntecusa.com/product/ar-15-stainless-steel-car-buffer/","price":29.95,"sku":"CARBUF-SS","in_stock":true,"observed":"2026-10-20","via":"user","note":"Guntec's own page, as the user saved it from their browser on 2026-10-20: the site refuses the reader and is never asked (D59). Its markup states the price (product:price:amount 29.95); the page shows SKU CARBUF-SS."}],"hexmag-series-2-ar15-30":[{"vendor":"kygunco","url":"https://www.kygunco.com/product/hexmag-series-2-gray-detachable-30rd-multi-cal-ar-15","price":8.91,"options":{"body":"gray"},"sku":"263430","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"KYGUNCO's page of the gray Series 2 30-round: its markup's number is its own item number (263430) with mpn HX30-AR-GRY; its UPC 085992200737 is Blackstone's for HX30-AR15S2-GRY."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/hexmag-30-round-magazine-series-2-blk-hx30-ar15s2-blk","price":11.99,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Primary Arms' page for the black one alone (HX30-AR15S2-BLK in its address and its text); its markup names no number (two offers at one price, the page's one product)."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/hexmag-30-round-magazine-series-2-fde-hx30-ar15s2-fde","price":11.99,"options":{"body":"fde"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Primary Arms' page for the FDE one alone; its markup names no number (two offers at one price)."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/hexmag-30-round-magazine-series-2-odg-hx30-ar15s2-odg","price":11.99,"options":{"body":"odg"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Primary Arms' page for the OD Green one alone; its markup names no number (two offers at one price)."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/hx30-ar15s2-blk","price":8.99,"options":{"body":"black"},"sku":"HX30-AR15S2-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest"}],"holosun-aro-kit":[{"vendor":"holosun","url":"https://www.holosun.com/products/aro-core-rd-2","price":188.22,"sku":"ARO-CORE-RD-2","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"alquist","url":"https://www.alquistarms.com/holosun-technologies-aro-red-dot-2-moa-dot-fits-1913-picatinny-rail-1-63-lower-1-3-co-witness-mount-black/","price":149,"sku":"ARO-RD2","in_stock":false,"observed":"2026-11-21","via":"harvest"}],"holosun-eps-carry":[{"vendor":"holosun","url":"https://www.holosun.com/products/eps-carry-rd-2","price":388.22,"sku":"EPS-CARRY-RD-2","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/holosun-eps-carry-enclosed-pistol-sight-2-moa-dot-red-reticle","price":329.99,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Primary Arms' page of the 2 MOA red EPS Carry; its markup names no number (make offers show, 2026-11-06: 329.99 USD, sku -)."}],"holosun-hm3x":[{"vendor":"holosun","url":"https://www.holosun.com/products/hm3x","price":235.28,"sku":"HM3X","in_stock":true,"observed":"2026-11-21","via":"harvest"}],"holosun-hs510c":[{"vendor":"holosun","url":"https://www.holosun.com/products/hs510c","price":364.69,"options":{"body":"black"},"sku":"HS510C","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/holosun-hs510c-hud-solar-powered-red-dot-sight-with-circle-dot-reticle","price":272.79,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product; its offer markup names no number."},{"vendor":"kygunco","url":"https://www.kygunco.com/product/holosun-hs510c-circle-dotsolar-panelqd-mount-reflex-sights","price":309.99,"options":{"body":"black"},"sku":"142604","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/hs510c","price":309.99,"options":{"body":"black"},"sku":"HS510C","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"faxon","url":"https://faxonfirearms.com/holosun-hs510c-red-dot/","price":352.93,"options":{"body":"black"},"sku":"HS510C","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"holosun","url":"https://www.holosun.com/products/hs510c-fde","price":364.69,"options":{"body":"fde"},"sku":"HS510C-FDE","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/holosun-hs510c-open-reflex-circle-dot-sight-fde","price":272.79,"options":{"body":"fde"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (the FDE sight, HS510C-FDE-R in its text); its offer markup names no number, and carries the one price twice."},{"vendor":"sportsmans","url":"https://www.sportsmans.com/hunting-gear-supplies/optics-binoculars-scopes-rangefinders/red-dots/holosun-hs510c-1x-red-dot-reflex-sight-2-moa-dot65-moa-circle/p/1772124","price":272.79,"options":{"body":"fde"},"sku":"1772124","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Sportsman's own number; its markup's mpn is HS510C-FDE-R and its page says \"Finish Flat Dark Earth Anodized\"."}],"huxwrx-flash-hider-qd-556":[{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/huxwrx-556-qd-flash-hider-1-2x28/","price":129,"sku":"22296","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The seller's own number; the page's title ends '- 1677'."},{"vendor":"alexanders","url":"https://alexandersstore.com/product/hux-flash-hider-qd-556-1-2x28/","price":129,"sku":"1677","in_stock":false,"observed":"2026-11-18","via":"harvest","note":"The markup carries the maker's number as its mpn."}],"huxwrx-flow-556-ti":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/huxwrx-flow-5-56-ti-suppressor-black","price":1185,"options":{"body":"black"},"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product in black (SKU 3059, MPN 3059 in its heading); the markup names no number"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/huxwrx-flow-556-ti-556-nato-suppressor-fde","price":1185,"options":{"body":"fde"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product in FDE (SKU 2693, MPN 2693 in its heading); the markup names no number"},{"vendor":"capitol-armory","url":"https://www.capitolarmory.com/huxwrx-flow-556-ti-titanium-556-ar15-rifle-silencer.html","price":1185,"sku":"HUX-556TI-3292","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One price for either colour, chosen on the page; \"Capitol Armory sells the FLOW 556 Ti without a muzzle device\" (a flash hider or a brake is an option at $114 more). The seller's own number, though it ends in the black kit's 3292."}],"huxwrx-flow-556k":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/huxwrx-flow-556k-suppressor-only-black","price":1054,"options":{"body":"black"},"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product in black (SKU HX-2448, MPN 2448 in its heading); the markup names no number"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/huxwrx-flow-556k-suppressor-only-fde","price":1054,"options":{"body":"fde"},"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product in FDE (SKU 2159, MPN 2159 in its heading); the markup names no number"},{"vendor":"capitol-armory","url":"https://www.capitolarmory.com/huxwrx-flow-556k.html","price":1054,"sku":"HUX-OSS2450","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"One price for either colour, chosen on the page; \"Capitol Armory sells the FLOW 556K without a muzzle device\" (a flash hider or a brake is an option at $114 more). The seller's own number."}],"jp-silent-captured-spring-gen2-h2":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/JPSCS2-15H2","price":178.16,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (SKU and MPN JPSCS2-15H2 in its text); its offer markup names no number (make offers show, 2026-10-18)."},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/101762715","price":188.05,"sku":"856665","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"MidwayUSA's own number for this product in its markup (its mpn the UPC 812872023984, AR15Discounts' UPC for JPSCS2-15H2; its page: \"Features H2 buffer version\")."},{"vendor":"silencer-shop","url":"https://www.silencershop.com/jp-gen-2-silent-captured-spring-heavy-buffer-ar15.html","price":180,"sku":"JPSCS2-15H2","in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/jp-enterprises-gen-2-silent-capture-spring-w-h2-buffer-ar-15/","price":187.95,"sku":"3788","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its markup's number for this product (its page: \"MPN JPSCS2-15H2\"); out of stock when read, 2026-10-18."},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/jp-enterprises-gen-2-silent-capture-spring-w-h2-buffer-ar-15/","price":188.05,"sku":"3788","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its markup's number for this product (mpn JPSCS2-15H2); out of stock when read, 2026-10-18."}],"jp-silent-captured-spring-gen2":[{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/101762705","price":132.95,"sku":"767861","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/jp-silent-captured-spring-for-ar15-gen-2","price":125.96,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (SKU and MPN JPSCS2-15 in its text); its offer markup names no number (make offers show, 2026-10-18)."},{"vendor":"silencer-shop","url":"https://www.silencershop.com/jp-gen-2-silent-captured-spring-ar15.html","price":125,"sku":"JPSCS2-15","in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/jp-enterprises-gen-2-silent-capture-spring-ar-15/","price":139.95,"sku":"3787","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its markup's number for this product (mpn JPSCS2-15); out of stock when read, 2026-10-18."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/jp-enterprises-gen-2-silent-capture-spring-ar-15/","price":115.95,"sku":"3787","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its markup's number for this product (mpn JPSCS2-15); out of stock when read, 2026-10-18."}],"kynshot-rb5000":[{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/1024517165","price":112.49,"sku":"614230","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/kynshot-precision-carbine-recoil-damper-for-5-56-223-rb5000","price":119.99,"sku":"RB5000","in_stock":true,"observed":"2026-11-17","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/kynshot-precision-carbine-recoil-damper-for-5-56-223/","price":149.99,"sku":"6764","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"impact-guns","url":"https://www.impactguns.com/stocks-forends/kynshot-ar-15-carbine-stock-recoil-buffer-854476005003-rb5000","price":124.69,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (its address ends in the UPC 854476005003 and the maker's number); its offer markup names no number, and carries the one price twice."}],"kynshot-rb5000hp":[{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/1024517262","price":149.99,"sku":"418309","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/kynshot-precision-high-performance-carbine-recoil-damper-for-5-56-223/","price":149.99,"sku":"6767","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"impact-guns","url":"https://www.impactguns.com/stocks-forends/kynshot-ar-15-cmmg-over-gassed-recoil-buffer-854476005379-rb5000hp","price":115.19,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (its address ends in the UPC 854476005379 and the maker's number); its offer markup names no number, and carries the one price twice."}],"larue-mbt-2s":[{"vendor":"larue","url":"https://larue.com/mbt-2-stage-ar-triggers-mc7h/","price":139.99,"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The page's price before a trigger style (straight or curved bow) is chosen."},{"vendor":"impact-guns","url":"https://www.impactguns.com/triggers/larue-tactical-mbt-2s-two-stage-straight-trigger-for-ar10-ar15-black-810143180992-ltmbt2ssb","price":100.99,"in_stock":true,"observed":"2026-11-21","via":"harvest"}],"law-tactical-gen-s-folder":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/https-www.primaryarms.com-law-tactical-ar-folding-stock-adapter-gen-s","price":269.99,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The page's markup names no number (two offers of one price, $269.99); the page itself: \"SKU: 430116178 MPN: 99329\"."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/law-tactical-ar-folding-stock-adapter-gen-s-black-oem/","price":249.99,"options":{"body":"black"},"sku":"6704","in_stock":true,"observed":"2026-11-21","via":"harvest"}],"law-tactical-gen3m-folder":[{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/99312","price":269.99,"options":{"body":"black"},"sku":"99312","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/ltgen3mfde","price":259,"options":{"body":"fde"},"sku":"LTGEN3MFDE","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/law-folder-ar-m4-gen-3/","price":265,"options":{"body":"black"},"sku":"75086","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/law-folder-ar-m4-gen-3/","price":275,"options":{"body":"fde"},"sku":"75087","in_stock":false,"observed":"2026-11-21","via":"harvest"}],"magpul-ctr":[{"vendor":"magpul","url":"https://magpul.com/ctr-carbine-stock-mil-spec.html","price":69.95,"in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/magpul-ctr-carbine-stock-mil-spec-black-mag310-blk","price":66.45,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Primary Arms' page for the black one alone; its markup names no number (it carried MAG310-BLK when it was first read, 2026-10-02)."},{"vendor":"wing-tactical","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/stocks-accessories/magpul-ctr-compact-type-restricted-stock-mil-spec/","price":64.95,"sku":"MAG-310","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One price for the colours the page offers: Black, Flat Dark Earth, Foliage Green, OD Green, Stealth Gray."},{"vendor":"academy","url":"https://www.academy.com/p/magpul-ctr-mil-spec-receiver-extension-carbine-stock","price":69.99,"options":{"body":"black"},"sku":"1204629","in_stock":true,"observed":"2026-11-10","via":"harvest","note":"Academy's own number for the black one."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/magpul-ctr-carbine-stock-mil-spec-stock-modified-coyote-brown","price":66.45,"options":{"body":"mcb"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Primary Arms' page for the Modified Coyote Brown stock alone; its markup names no number."}],"magpul-mbus-3-front":[{"vendor":"magpul","url":"https://magpul.com/mbus-3-sight-front.html","price":39.95,"in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/magpul-mbus-3-sight-front-865852","price":37.95,"options":{"body":"black"},"sku":"865853","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/magpul-mbus-3-sight-front-865852","price":37.95,"options":{"body":"fde"},"sku":"865854","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/magpul-mbus-3-sight-front-865852","price":37.95,"options":{"body":"odg"},"sku":"865855","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"wing-tactical","url":"https://www.wingtactical.com/accessories/optics-sights/sights/magpul-back-up-sight-mbus-3-front/","price":37.95,"sku":"MAG-1166","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/magpul-mbus-gen-3-folding-front-sight-black/","price":37.95,"options":{"body":"black"},"sku":"16448","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/mag1166-fde","price":37.95,"options":{"body":"fde"},"sku":"MAG1166-FDE","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"mile-high","url":"https://www.milehighshooting.com/magpul-mbus-3-sight-front/","price":37.95,"options":{"body":"black"},"sku":"MAG1166-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"alexanders","url":"https://alexandersstore.com/product/magpul-mbus-3-front-sight-blk/","price":37.95,"options":{"body":"black"},"sku":"MAG1166-BLK","in_stock":true,"observed":"2026-11-18","via":"harvest"},{"vendor":"alexanders","url":"https://alexandersstore.com/product/magpul-mbus-3-front-sight-fde/","price":37.95,"options":{"body":"fde"},"sku":"MAG1166-FDE","in_stock":true,"observed":"2026-11-18","via":"harvest"},{"vendor":"alexanders","url":"https://alexandersstore.com/product/magpul-mbus-3-front-sight-odg/","price":37.95,"options":{"body":"odg"},"sku":"MAG1166-ODG","in_stock":true,"observed":"2026-11-18","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/magpul-mbus-gen-3-folding-front-sight/","price":37.95,"sku":"16448","in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/magpul-mbus-3-front-sight-olive-drab-green","price":37.95,"options":{"body":"odg"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Primary Arms' page for this one product (MAG1166-ODG); its markup named that number until October 2026 and names none since"},{"vendor":"scheels","url":"https://www.scheels.com/p/magpul-mbus-3-front-sight/873750-MAG1166/","price":39.99,"sku":"84081513216","in_stock":true,"observed":"2026-10-05","via":"harvest"},{"vendor":"sportsmans","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/gun-parts-accessories/gun-parts-magazines/gun-sights-lasers/magpul-mbus-3-flip-up-front-sight-black/p/1693787","price":37.99,"options":{"body":"black"},"sku":"1693787","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"right-to-bear","url":"https://www.righttobear.com/magpul-mbus-3-flip-up-front-sight-blk/","price":37.95,"options":{"body":"black"},"sku":"MAG1166-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"rifle-supply","url":"https://riflesupply.com/Magpul-MBUS-3-Flip-Up-Front-Sight-FDE-AR-15-AR-10-M4-M16-MAG1166-FDE_p_5782.html","price":43.99,"options":{"body":"fde"},"sku":"5782","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"kygunco","url":"https://www.kygunco.com/product/magpul-mag1166-blk-mbus-3-sight-front-black","price":24.99,"options":{"body":"black"},"sku":"159442","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"impact-guns","url":"https://www.impactguns.com/sights/magpul-mbus-3-back-up-front-sight-tool-less-elevation-adjustment-ambidextrous-push-button-deployment-fits-picatinny-rails-black-840815132165-mag1166-blk","price":30.99,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"gritr","url":"https://gritroutdoors.com/magpul-mbus-3-front-sight-fde-mag1166-fde","price":36.95,"options":{"body":"fde"},"sku":"MAG-MAG1166-FDE","in_stock":true,"observed":"2026-11-21","via":"harvest"}],"magpul-mbus-3-rear":[{"vendor":"magpul","url":"https://magpul.com/mbus-3-sight-rear.html","price":59.95,"in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/magpul-mbus-3-sight-rear-865862","price":56.95,"options":{"body":"black"},"sku":"865865","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/magpul-mbus-3-sight-rear-865862","price":56.95,"options":{"body":"fde"},"sku":"865866","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/magpul-mbus-3-sight-rear-865862","price":56.95,"options":{"body":"odg"},"sku":"865867","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"wing-tactical","url":"https://www.wingtactical.com/accessories/optics-sights/sights/magpul-back-up-sight-mbus-3-rear/","price":56.95,"sku":"MAG-1167","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/mag1167-blk","price":56.95,"options":{"body":"black"},"sku":"MAG1167-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/mag1167-fde","price":56.95,"options":{"body":"fde"},"sku":"MAG1167-FDE","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"mile-high","url":"https://www.milehighshooting.com/magpul-mbus-3-sight-rear/","price":56.95,"options":{"body":"black"},"sku":"MAG1167-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"alexanders","url":"https://alexandersstore.com/product/magpul-mbus-3-rear-sight-fde/","price":56.95,"options":{"body":"fde"},"sku":"MAG1167-FDE","in_stock":true,"observed":"2026-11-18","via":"harvest"},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/magpul-mbus-gen-3-folding-rear-sight-black/","price":56.95,"options":{"body":"black"},"sku":"16449","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/magpul-mbus-gen-3-folding-rear-sight/","price":46.95,"options":{"body":"black"},"sku":"16449","in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/magpul-mbus-gen-3-folding-rear-sight/","price":56.95,"options":{"body":"fde"},"sku":"110888","in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/magpul-mbus-gen-3-folding-rear-sight/","price":56.95,"options":{"body":"odg"},"sku":"110892","in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/magpul-mbus-3-rear-sight-olive-drab-green","price":56.95,"options":{"body":"odg"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Primary Arms' page for this one product (MAG1167-ODG); its markup named that number until October 2026 and names none since"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/magpul-mbus-3-rear-sight-flat-dark-earth","price":56.95,"options":{"body":"fde"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Primary Arms' page for this one product (MAG1167-FDE); its markup named that number until October 2026 and names none since"},{"vendor":"scheels","url":"https://www.scheels.com/p/magpul-mbus-3-rear-sight/873750-MAG1167/","price":59.99,"options":{"body":"black"},"sku":"84081513219","in_stock":true,"observed":"2026-10-05","via":"harvest"},{"vendor":"sportsmans","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/gun-parts-accessories/gun-parts-magazines/gun-sights-lasers/magpul-mbus-3-flip-up-rear-sight-black/p/1693789","price":56.99,"options":{"body":"black"},"sku":"1693789","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"sportsmans","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/gun-parts-accessories/gun-parts-magazines/gun-sights-lasers/magpul-mbus-3-flip-up-rear-sight-fde/p/1693790","price":56.99,"options":{"body":"fde"},"sku":"1693790","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"right-to-bear","url":"https://www.righttobear.com/magpul-mbus-3-flip-up-rear-sight-fde/","price":56.95,"options":{"body":"fde"},"sku":"MAG1167-FDE","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"rifle-supply","url":"https://riflesupply.com/magpul-industries-mbus-3-back-up-rear-sight-sights-ambidextrous-picatinny-rail-od-green-mag1167-odg/","price":67.49,"options":{"body":"odg"},"sku":"7966","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"kygunco","url":"https://www.kygunco.com/product/magpul-mag1167-blk-mbus-3-sight-rear","price":37.99,"options":{"body":"black"},"sku":"159443","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"impact-guns","url":"https://www.impactguns.com/sights/magpul-mbus-3-back-up-rear-sight-olive-drab-green-fits-picatinny-rails-840815132219-mag1167-odg","price":56.95,"options":{"body":"odg"},"in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"gritr","url":"https://gritroutdoors.com/magpul-mbus-3-rear-sight-fde-mag1167-fde","price":56.95,"options":{"body":"fde"},"sku":"MAG-MAG1167-FDE","in_stock":true,"observed":"2026-11-21","via":"harvest"}],"magpul-mbus-pro-front":[{"vendor":"magpul","url":"https://magpul.com/firearm-accessories/sights/mbus-pro/mbus-pro-sight-front.html","price":104.95,"in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/magpul-mbus-pro-flip-up-front-sight-black-mag275-blk","price":99.7,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Primary Arms' page for this one product (MAG275-BLK); its markup named that number until October 2026 and names none since"},{"vendor":"wing-tactical","url":"https://www.wingtactical.com/accessories/ar-15-sights-and-optics/ar-15-sights/magpul-mbus-pro-front-sight/","price":94.95,"sku":"MAG-275","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"gritr","url":"https://gritroutdoors.com/magpul-mbus-black-front-pro-sight-mag275","price":85.08,"sku":"MAG-MAG275","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/MAG275","price":90.2,"sku":"MAG275","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"scheels","url":"https://www.scheels.com/p/magpul-mbus-pro-sight-front/873750-MAG275/","price":99.99,"sku":"87375000837","in_stock":true,"observed":"2026-10-05","via":"harvest"},{"vendor":"sportsmans","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/gun-parts-accessories/gun-parts-magazines/gun-sights-lasers/magpul-mbus-pro-back-up-front-sight/p/1385313","price":94.99,"sku":"1385313","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"right-to-bear","url":"https://www.righttobear.com/magpul-mbus-pro-flip-up-front-sight-black-mag275/","price":94.95,"sku":"MAG275","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"impact-guns","url":"https://www.impactguns.com/Sights/MagPul-MBUS-Pro-Front-Flip-Up-Sight-Black-873750008370-MAG275-BLK/","price":81.99,"in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"mile-high","url":"https://www.milehighshooting.com/magpul-mbus-pro-sight-front/","price":99.7,"sku":"MAG275-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"kygunco","url":"https://www.kygunco.com/product/magpul-mag275-blk-mbus-pro-flip-front-sight-ar15-m4-black","price":66.99,"sku":"122232","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"alexanders","url":"https://alexandersstore.com/product/magpul-mbus-pro-frnt-flip-sight-blk/","price":99.7,"sku":"MAG275-BLK","in_stock":true,"observed":"2026-11-18","via":"harvest"},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/magpul-mbus-pro-front-flip-sight-black/","price":99.7,"sku":"2598","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"rifle-supply","url":"https://riflesupply.com/Magpul-Mbus-Pro-Front-Sight-MAG275-BLK_p_530.html","price":96.49,"sku":"530","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/magpul-mbus-pro-front-flip-sight-black/","price":84.95,"sku":"2598","in_stock":true,"observed":"2026-11-21","via":"harvest"}],"magpul-mbus-pro-rear":[{"vendor":"magpul","url":"https://magpul.com/mbus-pro-sight-rear.html","price":124.95,"in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/magpul-mbus-pro-flip-up-rear-sight-black-mag276-blk","price":118.7,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Primary Arms' page for this one product (MAG276-BLK); its markup named that number until October 2026 and names none since"},{"vendor":"wing-tactical","url":"https://www.wingtactical.com/accessories/ar-15-sights-and-optics/ar-15-sights/magpul-back-up-rear-sight-mbus-pro/","price":109.95,"sku":"MAG-276","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/MAG276","price":109.2,"sku":"MAG276","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"scheels","url":"https://www.scheels.com/p/magpul-mbus-pro-rear-sight/873750-MAG276-BLK/","price":118.99,"sku":"87375000838","in_stock":true,"observed":"2026-10-05","via":"harvest"},{"vendor":"sportsmans","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/gun-parts-accessories/gun-parts-magazines/gun-sights-lasers/magpul-mbus-pro-rear-back-up-sight/p/1385294","price":114.99,"sku":"1385294","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"right-to-bear","url":"https://www.righttobear.com/MagPul-MBUS-Pro-Flip-Up-Rear-Sight-Black-p/mag276.htm","price":114.95,"sku":"MAG276","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"impact-guns","url":"https://www.impactguns.com/sights/magpul-mbus-pro-rear-sight-ar-black-873750008387-mag276-blk/","price":102.99,"in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"mile-high","url":"https://www.milehighshooting.com/magpul-mbus-pro-mag276-rear-flip-up-sight-black/","price":118.7,"sku":"MAG276-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"kygunco","url":"https://www.kygunco.com/product/magpul-mag276-blk-mbus-pro-rear-flip-sight-ar15m4-black","price":79.99,"sku":"64800","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"alexanders","url":"https://alexandersstore.com/product/magpul-mbus-pro-rear-flip-sight-blk/","price":118.7,"sku":"MAG276-BLK","in_stock":true,"observed":"2026-11-18","via":"harvest"},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/magpul-mbus-pro-rear-flip-sight-black/","price":99.7,"sku":"2599","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"gritr","url":"https://gritroutdoors.com/magpul-mbus-pro-rear-sight-mag276-blk","price":105.2,"sku":"MAG-MAG276","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"rifle-supply","url":"https://riflesupply.com/Magpul-Mbus-Pro-Rear-Sight-MAG276-BLK_p_532.html","price":118.49,"sku":"532","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/magpul-mbus-pro-rear-flip-sight-black/","price":99.95,"sku":"2599","in_stock":true,"observed":"2026-11-21","via":"harvest"}],"magpul-mlok-aluminum-rail-section-3-slot":[{"vendor":"magpul","url":"https://magpul.com/m-lokaluminumrail-3slots.html","price":20.95,"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Magpul's own page: its markup carries the one price twice (two microdata offers, no number on either); the page sells the one variant, MAG580-BLK."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/mag580","price":18,"sku":"MAG580","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/magpul-m-lok-aluminum-rail-section-3-slot-mag580","price":16.92,"sku":"MAG580","in_stock":true,"observed":"2026-11-17","via":"harvest"}],"magpul-mlok-aluminum-rail-section-5-slot":[{"vendor":"magpul","url":"https://magpul.com/m-lokaluminumrail-5slots.html","price":22.95,"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Magpul's own page: its markup carries the one price twice (two microdata offers, no number on either); the page sells the one variant, MAG581-BLK."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/magpul-m-lok-aluminum-rail-section-5-slot-mag581","price":18.53,"sku":"MAG581","in_stock":true,"observed":"2026-11-17","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/mag581","price":19.9,"sku":"MAG581","in_stock":true,"observed":"2026-11-21","via":"harvest"}],"magpul-mlok-aluminum-rail-section-7-slot":[{"vendor":"magpul","url":"https://magpul.com/m-lokaluminumrail-7slots.html","price":24.95,"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Magpul's own page: its markup carries the one price twice (two microdata offers, no number on either); the page sells the one variant, MAG582-BLK."},{"vendor":"kygunco","url":"https://www.kygunco.com/product/magpul-mag582-blk-m-lok-aluminum-rail-section-7-slots-blk","price":17.02,"sku":"122223","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"KYGunCo's own number in the markup (its mpn MAG582-BLK)."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/magpul-m-lok-aluminum-rail-section-7-slot-mag582","price":20.15,"sku":"MAG582","in_stock":true,"observed":"2026-11-17","via":"harvest"}],"magpul-mlok-aluminum-rail-section-9-slot":[{"vendor":"magpul","url":"https://magpul.com/m-lokaluminumrail-9slots.html","price":26.95,"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Magpul's own page: its markup carries the one price twice (two microdata offers, no number on either); the page sells the one variant (MAG583_RET_BLK_ in its data)."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/mag583","price":23.7,"sku":"MAG583","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/magpul-m-lok-aluminum-rail-section-9-slot-mag583","price":21.76,"sku":"MAG583","in_stock":true,"observed":"2026-11-17","via":"harvest"}],"magpul-mlok-hand-stop-kit":[{"vendor":"magpul","url":"https://magpul.com/m-lok-handstop-kit.html","price":24.95,"in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"wing-tactical","url":"https://www.wingtactical.com/firearm-parts/ar-15/handguards-rails/rail-system-parts-accessories/magpul-m-lok-handstop-kit/","price":22.95,"sku":"MAG-608","in_stock":true,"observed":"2026-11-21","via":"harvest"}],"magpul-mlok-mvg":[{"vendor":"magpul","url":"https://magpul.com/m-lok-mvg-vertical-grip.html","price":22.95,"in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/magpul-mvg-m-lok-vertical-grip-black","price":21.8,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Primary Arms' page for the black one alone; its markup names no number (it carried MAG597-BLK when it was first read, 2026-10-02)."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/magpul-m-lok-mvg-vertical-grip-olive-drab-green-mag597-odg","price":21.8,"options":{"body":"odg"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Primary Arms' page for the Olive Drab Green one alone; its markup names no number (it carried MAG597-ODG when it was first read, 2026-10-02)."},{"vendor":"wing-tactical","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/grips-foregrips/foregrips/magpul-mvg-m-lok-vertical-grip/","price":19.5,"sku":"MAG-597","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"rifle-supply","url":"https://riflesupply.com/Magpul-Industries-MVG-M-Lok-FDE-MAG597-FDE_p_5220.html","price":26.99,"options":{"body":"fde"},"sku":"MAG597-FDE","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/magpul-m-lok-mvg-vertical-grip-flat-dark-earth-mag597-fde","price":21.8,"options":{"body":"fde"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Primary Arms' page for the Flat Dark Earth grip alone; its markup names no number."}],"magpul-mlok-polymer-rail-section-11-slot":[{"vendor":"magpul","url":"https://magpul.com/m-lokpolymerrailsection-11slots.html","price":16.95,"options":{"body":"black"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Magpul's page for MAG593 (one variant, MAG593_RET_BLK_ in its data); its markup's offer names no number, and carries the one price twice."}],"magpul-mlok-polymer-rail-section-3-slot":[{"vendor":"magpul","url":"https://magpul.com/m-lokpolymerrailsection-3slots.html","price":11.95,"options":{"body":"black"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Magpul's page for MAG589 (one variant, MAG589_RET_BLK_ in its data); its markup's offer names no number, and carries the one price twice."}],"magpul-mlok-polymer-rail-section-5-slot":[{"vendor":"magpul","url":"https://magpul.com/m-lokpolymerrailsection-5slots.html","price":11.95,"options":{"body":"black"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Magpul's page for MAG590 (one variant, MAG590_RET_BLK_ in its data); its markup's offer names no number, and carries the one price twice."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/magpul-industries-m-lok-rail-section-5-slot","price":9.65,"options":{"body":"black"},"sku":"MAG590","in_stock":true,"observed":"2026-11-17","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/mag590-blk","price":10.4,"options":{"body":"black"},"sku":"MAG590-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"kygunco","url":"https://kygunco.com/product/magpul-mag590-blk-m-lok-polymer-rail-section-5-slots-blk","price":7.99,"options":{"body":"black"},"sku":"64785","in_stock":true,"observed":"2026-11-21","via":"harvest"}],"magpul-mlok-polymer-rail-section-7-slot":[{"vendor":"magpul","url":"https://magpul.com/m-lokpolymerrailsection-7slots.html","price":14.95,"options":{"body":"black"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Magpul's page for MAG591 (one variant, MAG591_RET_BLK_ in its data); its markup's offer names no number, and carries the one price twice."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/magpul-industries-m-lok-rail-section-7-slot","price":12.07,"options":{"body":"black"},"sku":"MAG591","in_stock":true,"observed":"2026-11-17","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/mag591-blk","price":14.2,"options":{"body":"black"},"sku":"MAG591-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/magpul-m-lok-poly-rail-section-7-slots/","price":14.2,"options":{"body":"black"},"sku":"1652","in_stock":true,"observed":"2026-11-21","via":"harvest"}],"magpul-mlok-polymer-rail-section-9-slot":[{"vendor":"magpul","url":"https://magpul.com/m-lokpolymerrailsection-9slots.html","price":15.95,"options":{"body":"black"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Magpul's page for MAG592 (one variant, MAG592_RET_BLK_ in its data); its markup's offer names no number, and carries the one price twice."}],"magpul-mlok-qd-sling-mount":[{"vendor":"magpul","url":"https://magpul.com/m-lok-qd-sling-mount.html","price":20.95,"in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/magpul-m-lok-qd-sling-mount-mag606","price":19.9,"in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"wing-tactical","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/handguards-rails/rail-system-parts-accessories/magpul-m-lok-qd-sling-attachment/","price":18.95,"sku":"MAG-606-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/MAG606","price":18.95,"sku":"MAG606","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"scheels","url":"https://www.scheels.com/p/magpul-m-lok-qd-sling-mount/873750-MAG606/","price":19.99,"sku":"87375000284","in_stock":true,"observed":"2026-10-05","via":"harvest"},{"vendor":"sportsmans","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/gun-parts-accessories/gun-parts-magazines/slings-swivels/magpul-m-lok-qd-sling-mount/p/1403218","price":19.99,"sku":"1403218","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"right-to-bear","url":"https://www.righttobear.com/magpul-m-lok-qd-sling-mount-mag606/","price":18.95,"sku":"MAG606","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"mile-high","url":"https://www.milehighshooting.com/magpul-mag606-m-lok-qd-sling-mount/","price":19.9,"sku":"MAG606-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"alexanders","url":"https://alexandersstore.com/product/magpul-m-lok-qd-sling-mnt/","price":19.9,"sku":"MAG606-BLK","in_stock":true,"observed":"2026-11-18","via":"harvest"},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/magpul-m-lok-qd-sling-mount/","price":19.9,"sku":"6197","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"rifle-supply","url":"https://riflesupply.com/Magpul-Sling-Mount-M-LOK-QD-Black_p_4940.html","price":21.99,"sku":"4940","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/magpul-m-lok-qd-sling-mount/","price":15.95,"sku":"6197","in_stock":false,"observed":"2026-11-21","via":"harvest"}],"magpul-moe-carbine":[{"vendor":"magpul","url":"https://magpul.com/moe-carbine-stock-mil-spec.html","price":49.95,"in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/magpul-moe-carbine-stock-mil-spec-black-mag400-blk","price":40.33,"options":{"body":"black"},"sku":"MAG400-BLK","in_stock":true,"observed":"2026-11-17","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/magpul-moe-carbine-stock-mil-spec-flat-dark-earth-mag400-fde","price":40.33,"options":{"body":"fde"},"sku":"MAG400-FDE","in_stock":true,"observed":"2026-11-17","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/magpul-moe-carbine-stock-mil-spec-olive-drab-green-mag400-od","price":40.33,"options":{"body":"odg"},"sku":"MAG400-ODG","in_stock":false,"observed":"2026-11-17","via":"harvest"},{"vendor":"wing-tactical","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/stocks-accessories/magpul-moe-carbine-stock-mil-spec/","price":45.95,"sku":"MAG-400","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One price for the colours the page offers: Black, Flat Dark Earth, Foliage Green, OD Green, Stealth Gray."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/MAG400-BLK","price":47.45,"options":{"body":"black"},"sku":"MAG400-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/2319180434","price":47.45,"options":{"body":"black"},"sku":"910076","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"MidwayUSA's own number for the black one."},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/2319180434","price":47.45,"options":{"body":"fde"},"sku":"797174","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"MidwayUSA's own number for Flat Dark Earth."},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/2319180434","price":47.45,"options":{"body":"odg"},"sku":"455458","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"MidwayUSA's own number for Olive Drab."},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/2319180434","price":47.45,"options":{"body":"sgy"},"sku":"616066","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"MidwayUSA's own number for Stealth."}],"magpul-moe-k2-plus":[{"vendor":"magpul","url":"https://magpul.com/moe-k2-plus-grip-ar15-m4.html","price":24.95,"in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/magpul-moe-k2-plus-pistol-grip-black","price":20.15,"options":{"body":"black"},"sku":"MAG532-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"wing-tactical","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/grips-foregrips/pistol-grips/magpul-moe-k2-ar-15-grip/","price":21.95,"options":{"body":"black"},"sku":"MAG-532","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One price for the colours the page offers: Black, Flat Dark Earth, OD Green."},{"vendor":"wing-tactical","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/grips-foregrips/pistol-grips/magpul-moe-k2-ar-15-grip/","price":21.95,"options":{"body":"fde"},"sku":"MAG-532","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One price for the colours the page offers: Black, Flat Dark Earth, OD Green."},{"vendor":"wing-tactical","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/grips-foregrips/pistol-grips/magpul-moe-k2-ar-15-grip/","price":21.95,"options":{"body":"odg"},"sku":"MAG-532","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One price for the colours the page offers: Black, Flat Dark Earth, OD Green."},{"vendor":"mile-high","url":"https://www.milehighshooting.com/magpul-moe-k2-plus-grip-ar15-m4-fde/","price":23.7,"options":{"body":"fde"},"sku":"MAG532-FDE","in_stock":true,"observed":"2026-11-21","via":"harvest"}],"magpul-moe-mlok-handguard-carbine":[{"vendor":"magpul","url":"https://magpul.com/moem-lokhandguard-carbine-length-ar15-m4.html","price":36.95,"options":{"body":"black"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"One price for the four colours the page offers (its swatches: Black, Flat Dark Earth, Olive Drab Green, Stealth Gray); its markup names no number."},{"vendor":"magpul","url":"https://magpul.com/moem-lokhandguard-carbine-length-ar15-m4.html","price":36.95,"options":{"body":"fde"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"One price for the four colours the page offers (its swatches: Black, Flat Dark Earth, Olive Drab Green, Stealth Gray); its markup names no number."},{"vendor":"magpul","url":"https://magpul.com/moem-lokhandguard-carbine-length-ar15-m4.html","price":36.95,"options":{"body":"odg"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"One price for the four colours the page offers (its swatches: Black, Flat Dark Earth, Olive Drab Green, Stealth Gray); its markup names no number."},{"vendor":"magpul","url":"https://magpul.com/moem-lokhandguard-carbine-length-ar15-m4.html","price":36.95,"options":{"body":"gry"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"One price for the four colours the page offers (its swatches: Black, Flat Dark Earth, Olive Drab Green, Stealth Gray); its markup names no number."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/magpul-moe-m-lok-handguard-carbine-length-black","price":29.84,"options":{"body":"black"},"sku":"MAG424-BLK","in_stock":true,"observed":"2026-11-17","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/magpul-moe-m-lok-handguard-carbine-length-flat-dark-earth-mag424-fde","price":29.84,"options":{"body":"fde"},"sku":"MAG424-FDE","in_stock":true,"observed":"2026-11-17","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/magpul-moe-m-lok-handguard-carbine-length-olive-drab-green-mag424-odg","price":29.84,"options":{"body":"odg"},"sku":"MAG424-ODG","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/mag424-xx","price":35.1,"options":{"body":"black"},"sku":"MAG424-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/mag424-xx","price":35.1,"options":{"body":"fde"},"sku":"MAG424-FDE","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/mag424-xx","price":35.1,"options":{"body":"odg"},"sku":"MAG424-ODG","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/mag424-xx","price":35.1,"options":{"body":"gry"},"sku":"MAG424-GRY","in_stock":true,"observed":"2026-11-21","via":"harvest"}],"magpul-moe-mlok-handguard-mid":[{"vendor":"magpul","url":"https://magpul.com/moem-lokhandguard-mid-length-ar15-m4.html","price":36.95,"options":{"body":"black"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"One price for the four colours the page offers (its swatches: Black, Flat Dark Earth, Olive Drab Green, Stealth Gray); its markup names no number."},{"vendor":"magpul","url":"https://magpul.com/moem-lokhandguard-mid-length-ar15-m4.html","price":36.95,"options":{"body":"fde"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"One price for the four colours the page offers (its swatches: Black, Flat Dark Earth, Olive Drab Green, Stealth Gray); its markup names no number."},{"vendor":"magpul","url":"https://magpul.com/moem-lokhandguard-mid-length-ar15-m4.html","price":36.95,"options":{"body":"odg"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"One price for the four colours the page offers (its swatches: Black, Flat Dark Earth, Olive Drab Green, Stealth Gray); its markup names no number."},{"vendor":"magpul","url":"https://magpul.com/moem-lokhandguard-mid-length-ar15-m4.html","price":36.95,"options":{"body":"gry"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"One price for the four colours the page offers (its swatches: Black, Flat Dark Earth, Olive Drab Green, Stealth Gray); its markup names no number."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/magpul-moe-m-lok-handguard-mid-length-black-mag426-blk","price":29.84,"options":{"body":"black"},"sku":"MAG426-BLK","in_stock":true,"observed":"2026-11-17","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/magpul-moe-m-lok-handguard-mid-length-flat-dark-earth-mag426-fde","price":29.84,"options":{"body":"fde"},"sku":"MAG426-FDE","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/magpul-moe-m-lok-handguard-mid-length-olive-drab-green-mag426-odg","price":29.84,"options":{"body":"odg"},"sku":"MAG426-ODG","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/mag426-xx","price":35.1,"options":{"body":"black"},"sku":"MAG426-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/mag426-xx","price":35.1,"options":{"body":"fde"},"sku":"MAG426-FDE","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/mag426-xx","price":35.1,"options":{"body":"odg"},"sku":"MAG426-ODG","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/mag426-xx","price":35.1,"options":{"body":"gry"},"sku":"MAG426-GRY","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"kygunco","url":"https://www.kygunco.com/product/magpul-mag426-gry-moe-m-lok-hand-guard-mid-length-ar15m4-gry","price":28.8,"options":{"body":"gry"},"sku":"64951","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"KYGUNCO's own number; the markup's mpn is MAG426-GRY."}],"magpul-moe-plus":[{"vendor":"magpul","url":"https://magpul.com/moe-plus-grip-ar15-m4.html","price":24.95,"in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/magpul-moe-plus-pistol-grip-black","price":23.7,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Primary Arms' page for this one product (MAG416-BLK); its markup named that number until October 2026 and names none since"},{"vendor":"wing-tactical","url":"https://www.wingtactical.com/firearm-parts/ar-15/grips-accessories/pistol-grips/magpul-moe-grip/","price":22.95,"sku":"MAG-416","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One price for the colours the page offers: Black, Flat Dark Earth, Foliage Green, OD Green, Stealth Gray."},{"vendor":"right-to-bear","url":"https://www.righttobear.com/magpul-moe-plus-pistol-grip-ar-15-blk-mag416-blk/","price":22.75,"options":{"body":"black"},"sku":"MAG416-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest"}],"magpul-moe-sl-carbine":[{"vendor":"magpul","url":"https://magpul.com/moe-sl-carbine-stock-mil-spec.html","price":69.95,"in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/magpul-moe-slim-line-carbine-stock-mil-spec-black-mag347-blk","price":66.45,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Primary Arms' page for this one product (MAG347-BLK); its markup named that number until October 2026 and names none since"},{"vendor":"wing-tactical","url":"https://www.wingtactical.com/firearm-parts/ar-15/stocks-accessories/magpul-moe-sl-slim-line-stock-mil-spec/","price":62.95,"options":{"body":"black"},"sku":"MAG-347","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One price for the colours the page offers: Black, Flat Dark Earth, OD Green."},{"vendor":"wing-tactical","url":"https://www.wingtactical.com/firearm-parts/ar-15/stocks-accessories/magpul-moe-sl-slim-line-stock-mil-spec/","price":62.95,"options":{"body":"fde"},"sku":"MAG-347","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One price for the colours the page offers: Black, Flat Dark Earth, OD Green."},{"vendor":"wing-tactical","url":"https://www.wingtactical.com/firearm-parts/ar-15/stocks-accessories/magpul-moe-sl-slim-line-stock-mil-spec/","price":62.95,"options":{"body":"odg"},"sku":"MAG-347","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One price for the colours the page offers: Black, Flat Dark Earth, OD Green."},{"vendor":"mile-high","url":"https://www.milehighshooting.com/magpul-moe-sl-carbine-stock-mil-spec/","price":66.45,"options":{"body":"black"},"sku":"MAG347-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest"}],"magpul-moe-sl-handguard-carbine":[{"vendor":"magpul","url":"https://magpul.com/moeslhandguard-carbine-length-ar15-m4.html","price":39.95,"options":{"body":"black"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"One price for the four colours the page offers (its swatches: Black, Flat Dark Earth, Olive Drab Green, Stealth Gray); its markup names no number."},{"vendor":"magpul","url":"https://magpul.com/moeslhandguard-carbine-length-ar15-m4.html","price":39.95,"options":{"body":"fde"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"One price for the four colours the page offers (its swatches: Black, Flat Dark Earth, Olive Drab Green, Stealth Gray); its markup names no number."},{"vendor":"magpul","url":"https://magpul.com/moeslhandguard-carbine-length-ar15-m4.html","price":39.95,"options":{"body":"odg"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"One price for the four colours the page offers (its swatches: Black, Flat Dark Earth, Olive Drab Green, Stealth Gray); its markup names no number."},{"vendor":"magpul","url":"https://magpul.com/moeslhandguard-carbine-length-ar15-m4.html","price":39.95,"options":{"body":"gry"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"One price for the four colours the page offers (its swatches: Black, Flat Dark Earth, Olive Drab Green, Stealth Gray); its markup names no number."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/magpul-moe-slim-line-handguard-carbine-length-stealth-grey-mag538-gry","price":32.26,"options":{"body":"gry"},"sku":"MAG538-GRY","in_stock":false,"observed":"2026-11-01","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/mag538-xx","price":37.95,"options":{"body":"black"},"sku":"MAG538-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/mag538-xx","price":37.95,"options":{"body":"fde"},"sku":"MAG538-FDE","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/mag538-xx","price":37.95,"options":{"body":"odg"},"sku":"MAG538-ODG","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/mag538-xx","price":37.95,"options":{"body":"gry"},"sku":"MAG538-GRY","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"kygunco","url":"https://www.kygunco.com/product/magpul-mag538-gry-moe-sl-hand-guard-carbine-length-ar15m4-gry","price":31.13,"options":{"body":"gry"},"sku":"64862","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"KYGUNCO's own number; the markup's mpn is MAG538-GRY."}],"magpul-moe-sl-handguard-mid":[{"vendor":"magpul","url":"https://magpul.com/moeslhandguard-mid-length-ar15-m4.html","price":39.95,"options":{"body":"black"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"One price for the four colours the page offers (its swatches: Black, Flat Dark Earth, Olive Drab Green, Stealth Gray); its markup names no number."},{"vendor":"magpul","url":"https://magpul.com/moeslhandguard-mid-length-ar15-m4.html","price":39.95,"options":{"body":"fde"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"One price for the four colours the page offers (its swatches: Black, Flat Dark Earth, Olive Drab Green, Stealth Gray); its markup names no number."},{"vendor":"magpul","url":"https://magpul.com/moeslhandguard-mid-length-ar15-m4.html","price":39.95,"options":{"body":"odg"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"One price for the four colours the page offers (its swatches: Black, Flat Dark Earth, Olive Drab Green, Stealth Gray); its markup names no number."},{"vendor":"magpul","url":"https://magpul.com/moeslhandguard-mid-length-ar15-m4.html","price":39.95,"options":{"body":"gry"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"One price for the four colours the page offers (its swatches: Black, Flat Dark Earth, Olive Drab Green, Stealth Gray); its markup names no number."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/magpul-moe-sl-handguard-mid-length-flat-dark-earth-mag551-fde","price":32.26,"options":{"body":"fde"},"sku":"MAG551-FDE","in_stock":true,"observed":"2026-11-17","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/mag551-xx","price":37.95,"options":{"body":"black"},"sku":"MAG551-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/mag551-xx","price":37.95,"options":{"body":"fde"},"sku":"MAG551-FDE","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/mag551-xx","price":37.95,"options":{"body":"odg"},"sku":"MAG551-ODG","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/mag551-xx","price":37.95,"options":{"body":"gry"},"sku":"MAG551-GRY","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"kygunco","url":"https://www.kygunco.com/product/magpul-mag551-odg-moe-sl-hand-guard-mid-length-ar15-m4-odg","price":31.13,"options":{"body":"odg"},"sku":"122208","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"KYGUNCO's own number; the markup's mpn is MAG551-ODG."}],"magpul-moe-trigger-guard":[{"vendor":"magpul","url":"https://magpul.com/moe-enhanced-trigger-guard-polymer-ar15-m4.html","price":9.95,"in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"wing-tactical","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/lower-receiver-parts/lower-receiver-parts/magpul-moe-enhanced-polymer-trigger-guard/","price":8.85,"options":{"body":"black"},"sku":"MAG-1186","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One price for the colours the page offers: Black, Flat Dark Earth, OD Green."},{"vendor":"wing-tactical","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/lower-receiver-parts/lower-receiver-parts/magpul-moe-enhanced-polymer-trigger-guard/","price":8.85,"options":{"body":"fde"},"sku":"MAG-1186","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One price for the colours the page offers: Black, Flat Dark Earth, OD Green."},{"vendor":"wing-tactical","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/lower-receiver-parts/lower-receiver-parts/magpul-moe-enhanced-polymer-trigger-guard/","price":8.85,"options":{"body":"odg"},"sku":"MAG-1186","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One price for the colours the page offers: Black, Flat Dark Earth, OD Green."},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/magpul-moe-enhanced-trigger-guard-ar-15-m4/","price":10,"options":{"body":"black"},"sku":"865814","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"T.REX ARMS' own number for the black one."},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/magpul-moe-enhanced-trigger-guard-ar-15-m4/","price":10,"options":{"body":"fde"},"sku":"865815","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"T.REX ARMS' own number for FDE."},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/magpul-moe-enhanced-trigger-guard-ar-15-m4/","price":10,"options":{"body":"odg"},"sku":"865816","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"T.REX ARMS' own number for OD Green."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/mag1186","price":9.45,"options":{"body":"black"},"sku":"MAG1186-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest"}],"magpul-pmag-20-gen-m3":[{"vendor":"magpul","url":"https://magpul.com/pmag-20-ar-m4-gen-m3.html","price":15.95,"in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/magpul-pmag-20-ar15-m4-gen-m3-5.56-nato-magazine-black-polymer","price":15.15,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Primary Arms' page for the black one alone (its text: SKU MAG560-BLK); its markup names no number."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/MAG560-BLK","price":14.95,"options":{"body":"black"},"sku":"MAG560-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/magpul-pmag-20-ar-m4-gen-m3","price":14.95,"options":{"body":"black"},"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Aero's one page for the magazine (its own number APRH101755, 'Magpul SKU: MAG560'); its markup names no number, and its one picture is the black one's."},{"vendor":"mile-high","url":"https://www.milehighshooting.com/copy-of-magpul-mag291-blk-308-20-round-pmag-gen-3-black/","price":15.15,"options":{"body":"black"},"sku":"MAG560","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The address's slug is another product's; the page and its markup are MAG560's, black."},{"vendor":"gritr-sports","url":"https://gritrsports.com/magpul-pmag-20-black-magazine-mag560","price":16.99,"options":{"body":"black"},"sku":"MAG-MAG560-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"scheels","url":"https://www.scheels.com/p/magpul-pmag-20-ar%2Fm4-gen-m3-magazine/873750-MAG560-BLK","price":14.39,"options":{"body":"black"},"sku":"87375000791","in_stock":true,"observed":"2026-10-13","via":"harvest"},{"vendor":"academy","url":"https://www.academy.com/p/magpul-pmag-20-gen-m3-556-x-45-nato-ar-m4-magazine","price":15.99,"options":{"body":"black"},"sku":"115177025","in_stock":true,"observed":"2026-11-20","via":"harvest"},{"vendor":"kygunco","url":"https://www.kygunco.com/product/magpul-mag560-blk-pmag-m3-5.56-ar15m4-20rd-blk","price":11.99,"options":{"body":"black"},"sku":"65212","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/magpul-ar-m4-pmag-336599","price":14,"options":{"body":"black"},"sku":"339067","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page for the whole family (eight offers); 339067 is its 'M3, Non-Window, 5.56, 20 Rounds, Black'."},{"vendor":"impact-guns","url":"https://www.impactguns.com/rifle-magazines/magpul-pmag-ar-m4-gen-m3-5-56x45-magazine-20rd-873750007915-mag560-blk/","price":13.99,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Impact Guns' page for the black one alone (its address carries 873750007915 and mag560-blk); its markup names no number."},{"vendor":"sportsmans","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/gun-parts-accessories/gun-parts-magazines/magazines-clips/rifle-magazines/magpul-pmag-gen-m3-arm4-223556-rifle-magazine-20-rounds/p/1376789","price":15.99,"options":{"body":"black"},"sku":"1376789","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"rifle-supply","url":"https://riflesupply.com/Magpul-PMAG-ARM4-GEN-M3-20RD-223556NATO-Black-MAG560-BLK_p_2998.html","price":17.99,"options":{"body":"black"},"sku":"2998","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/magpul-pmag-m3-5-56-20rnd-black/","price":12.95,"options":{"body":"black"},"sku":"2587","in_stock":true,"observed":"2026-11-21","via":"harvest"}],"magpul-pmag-30-gen-m3":[{"vendor":"magpul","url":"https://magpul.com/pmag-30-ar-m4-gen-m3.html","price":15.95,"in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/magpul-pmag-30-ar15-m4-gen-m3-5.56-nato-magazine-black-polymer","price":12.88,"options":{"body":"black"},"sku":"MAG557-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Primary Arms' page for the black one alone; its markup names no number (it carried MAG557-BLK when it was first read, 2026-10-03)."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/MAG557-BLK","price":14.2,"options":{"body":"black"},"sku":"MAG557-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/MAG557-ODG","price":14.2,"options":{"body":"odg"},"sku":"MAG557-ODG","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"mile-high","url":"https://www.milehighshooting.com/magpul-mag557-blk-genm3-30-round-pmag-5-56-223-black/","price":15.15,"options":{"body":"black"},"sku":"MAG557-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/MAG557-MCT","price":14.2,"options":{"body":"mct"},"sku":"MAG557-MCT","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/MAG557-MCB","price":14.2,"options":{"body":"mcb"},"sku":"MAG557-MCB","in_stock":true,"observed":"2026-11-21","via":"harvest"}],"magpul-pmag-d-60":[{"vendor":"magpul","url":"https://magpul.com/pmag-d-60-ar-m4-gen-m3.html","price":139.95,"in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/magpul-pmag-5-56mm-d-60-drum-magazine-black-mag576-blk","price":113.01,"sku":"MAG576-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (MAG576-BLK in its address); its offer markup names no number."},{"vendor":"impact-guns","url":"https://www.impactguns.com/drum-mags/magpul-d-60-black-60-round-drum-magazine-for-ar15-m4-pattern-firearms-840815100560-mag576-blk","price":132.95,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (840815100560 and MAG576-BLK in its address); its offer markup names no number."},{"vendor":"scheels","url":"https://www.scheels.com/p/magpul-pmag-d-60-5.56x45-polymer-drum-magazine/873750-MAG576-BLK/","price":132.99,"sku":"84081510056","in_stock":true,"observed":"2026-10-06","via":"harvest","note":"The number the markup carries (the address has Scheels' own, 873750-MAG576-BLK)."},{"vendor":"sportsmans","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/gun-parts-magazines/magazines-clips/rifle-magazines/magpul-pmag-d60-ar15m4-223-remington556mm-nato-rifle-magazine-60-rounds/p/1408704","price":139.99,"sku":"1408704","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"right-to-bear","url":"https://www.righttobear.com/d60-pmag-5-56-drum-magazine-60-round-mag576-blk/","price":134.95,"sku":"MAG576-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"mile-high","url":"https://www.milehighshooting.com/magpul-mag576-pmag-d-60-ar-m4-5-56x45mm-nato/","price":132.95,"sku":"MAG576","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/MAG576-BLK","price":131.95,"sku":"MAG576-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"kygunco","url":"https://www.kygunco.com/product/magpul-mag576-blk-pmag-d-60rd-arm4-gen-m3-5.56x45-black","price":102.99,"sku":"64741","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"gritr-sports","url":"https://gritrsports.com/magpul-pmag-d-60-ar-m4-556mm-60rd-drum-mag-mag576-blk","price":116.99,"sku":"MAG-MAG576-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/magpul-pmag-d-60-5-56-60rd-black/","price":128.2,"sku":"3939","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The seller's own number, which the markup carries."},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/2319563127/","price":132.95,"sku":"719525","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"rifle-supply","url":"https://riflesupply.com/Magpul-Industries-D-60-AR15-Drum-Magazine-60RD-223556NATO-Black-MAG576-BLK_p_1750.html","price":139.95,"sku":"MAG576-BLK","in_stock":false,"observed":"2026-11-21","via":"harvest"}],"mas-defense-nero-12-62-handguard":[{"vendor":"mas-defense","url":"https://www.masdefense.com/MAS00106380-p/mas00106380.htm","price":94.99,"options":{"body":"stealth-gray"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"MAS's own page for this length in this colour; its markup names no number (one microdata offer)."},{"vendor":"mas-defense","url":"https://www.masdefense.com/MAS00106312-p/mas00106312.htm","price":79.99,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"MAS's own page for this length in this colour; its markup names no number (one microdata offer)."},{"vendor":"mas-defense","url":"https://www.masdefense.com/MAS00106362-p/mas00106362.htm","price":94.99,"options":{"body":"fde"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"MAS's own page for this length in this colour; its markup names no number (one microdata offer)."},{"vendor":"mas-defense","url":"https://www.masdefense.com/MAS00106212-ODG-p/mas00106212-odg.htm","price":94.99,"options":{"body":"od-green"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"MAS's own page for this length in this colour; its markup names no number (one microdata offer)."}],"mas-defense-nero-15-handguard":[{"vendor":"mas-defense","url":"https://www.masdefense.com/MAS00106384-p/mas00106384.htm","price":104.99,"options":{"body":"stealth-gray"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"MAS's own page for this length in this colour; its markup names no number (one microdata offer)."},{"vendor":"mas-defense","url":"https://www.masdefense.com/MAS00106314-p/mas00106314.htm","price":89.99,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"MAS's own page for this length in this colour; its markup names no number (one microdata offer)."},{"vendor":"mas-defense","url":"https://www.masdefense.com/MAS00106364-p/mas00106364.htm","price":104.99,"options":{"body":"fde"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"MAS's own page for this length in this colour; its markup names no number (one microdata offer)."},{"vendor":"mas-defense","url":"https://www.masdefense.com/MAS00106214-BLU-p/mas00106214-blu.htm","price":104.99,"options":{"body":"navy-blue"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"MAS's own page for this length in this colour; its markup names no number (one microdata offer)."},{"vendor":"mas-defense","url":"https://www.masdefense.com/MAS00106214-ODG-p/mas00106214-odgb.htm","price":99.99,"options":{"body":"od-green"},"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"MAS's own page for this length in this colour; its markup names no number (one microdata offer)."}],"mas-defense-nero-9-87-handguard":[{"vendor":"mas-defense","url":"https://www.masdefense.com/MAS00106375-p/mas00106378.htm","price":84.99,"options":{"body":"stealth-gray"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"MAS's own page for this length in this colour; its markup names no number (one microdata offer)."},{"vendor":"mas-defense","url":"https://www.masdefense.com/MAS00106308-p/mas00106308.htm","price":69.99,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"MAS's own page for this length in this colour; its markup names no number (one microdata offer)."},{"vendor":"mas-defense","url":"https://www.masdefense.com/MAS00106358-p/mas00106358.htm","price":84.99,"options":{"body":"fde"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"MAS's own page for this length in this colour; its markup names no number (one microdata offer)."},{"vendor":"mas-defense","url":"https://www.masdefense.com/MAS00106208-ODG-p/mas00106208-odg.htm","price":84.99,"options":{"body":"od-green"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"MAS's own page for this length in this colour; its markup names no number (one microdata offer)."},{"vendor":"mas-defense","url":"https://www.masdefense.com/MAS00106208-BLU-p/mas00106208-blu.htm","price":84.99,"options":{"body":"navy-blue"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"MAS's own page for this length in this colour; its markup names no number (one microdata offer)."}],"mft-battlelink-minimalist-stock":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/mission-first-tactical-battlelink-minimalist-stock-mil-spec-black","price":59.99,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product in black (the page says SKU: MFTBMSMILBLK, MPN: BMSMIL); its offer markup names no number."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/mission-first-tactical-battlelink-minimalist-stock-milspec-scorched-dark-earth","price":59.99,"options":{"body":"sde"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product in Scorched Dark Earth (the page says SKU: MFTBMSMILSDE, MPN: BMSMILSDE); its offer markup names no number."},{"vendor":"wing-tactical","url":"https://www.wingtactical.com/firearm-parts/ar-15/stocks-accessories/mission-first-tactical-battlelink-minimalist-stock-mil-spec/","price":59.99,"sku":"MFT-BMSMIL","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One page and one price for both colours (the shop's own number; 'Finish: Black and Scorched Dark Earth')."},{"vendor":"kygunco","url":"https://kygunco.com/product/mft-bmsmil-battlelink-minimalist-milspec-stock-black","price":59.99,"options":{"body":"black"},"sku":"66353","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The black one (the shop's item number; the markup's mpn is BMSMIL, its gtin 676315025856)."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/mft-battlelink-minimalist-stock-mil-spec-black-oem/","price":49.99,"options":{"body":"black"},"sku":"24258","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The black one, 'OEM' in its name (the page's own number; MPN BMSMIL in its table). Out of stock when read."},{"vendor":"redcon1","url":"https://redcon1tactical.com/mission-first-tactical-battlelink-minimalist-stock-bms-mil-spec-black.html","price":59.99,"options":{"body":"black"},"sku":"BMSMIL","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The black one (the markup carries the maker's number as its mpn)."},{"vendor":"right-to-bear","url":"https://www.righttobear.com/mission-first-bmsmil-battlelink-minimalist-stock-bmsmil-bl/","price":33.95,"options":{"body":"black"},"sku":"BMSMIL-BL","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The black one, sold from bulk without the maker's packaging (the page says so). Out of stock when read."},{"vendor":"impact-guns","url":"https://www.impactguns.com/Grips/Mission-First-Tactical-Battlelink-Minimalist-Stock-Mil-Spec-Size-1-148-Diameter-Receiver-Extensions-Black-676315025856-BATTLELINK/","price":51.99,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product in black (its address ends in the UPC 676315025856); its offer markup names no number."}],"midwest-combat-rail-15-handguard":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/midwest-industries-15in-combat-rail-m-lok-ar-15-handguard-black","price":209.95,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (its text: SKU: MI-CRM-15.0, MPN: MI-CRM-15.0); the markup names no number, and states the one price twice."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/mi-crm15","price":209.95,"options":{"body":"black"},"sku":"MI-CRM15","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"right-to-bear","url":"https://www.righttobear.com/midwest-combat-rail-free-float-handguard-15-inch-mi-crm15/","price":279.99,"options":{"body":"black"},"sku":"MI-CRM15","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"bcm","url":"https://bravocompanyusa.com/mi-15-combat-rail-one-piece-free-float-handguard-m-lok-tm-compatible/","price":199.95,"options":{"body":"black"},"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Bravo Company's page for this one product (its text: SKU: MI-CRM15); the markup names no number."},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/midwest-industries-ar-15-m-lok-free-float-combat-rail-handguard/","price":209.95,"options":{"body":"black"},"sku":"17806","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"A page for thirteen lengths, each an offer under the shop's own number: 17806 is \"Combat Rail Handguard - 15\"\"."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/midwest-industries-ar-15-m-lok-free-float-combat-rail-handguard/","price":209.95,"options":{"body":"black"},"sku":"17806","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"A page for thirteen lengths, each an offer under the shop's own number: 17806 is \"Combat Rail Handguard - 15\"."}],"midwest-industries-drop-in-mlok-carbine":[{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/M-SERIES","price":85,"options":{"body":"black"},"sku":"MI-17M-BK","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"One page for the three lengths; its markup gives each its own number and price (MI-17M-BK, MI-18M-BK, MI-19M-BK)."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/midwest-industries-ar-15-2-piece-m-lok-drop-in-handguard/","price":136.95,"options":{"body":"black"},"sku":"17849","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"One page for the three lengths; the markup names this one \"Midwest Industries AR-15 2-Piece M-LOK Drop-In Handguard - carbine\" under the shop's own number 17849."}],"midwest-industries-drop-in-mlok-mid":[{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/M-SERIES","price":95,"options":{"body":"black"},"sku":"MI-18M-BK","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"One page for the three lengths; its markup gives each its own number and price (MI-17M-BK, MI-18M-BK, MI-19M-BK)."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/midwest-industries-ar-15-2-piece-m-lok-drop-in-handguard/","price":146.95,"options":{"body":"black"},"sku":"17850","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"One page for the three lengths; the markup names this one \"Midwest Industries AR-15 2-Piece M-LOK Drop-In Handguard - midlength\" under the shop's own number 17850."}],"midwest-mk2-qd-t2-226":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/midwest-industries-mk2-qd-aimpoint-t2-mount-nv-2-26-height","price":139.95,"options":{"mount":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The page of MI-MK2-QDT2NV-2.26 (its text: \"SKU: MI-MK2-QDT2NV-2.26 MPN: MI-MK2-QDT2NV-2.26\"), black, the one colour; its markup names no number (sku and mpn empty in its microdata)."}],"midwest-mk2-qd-t2-low":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/midwest-industries-mk2-qd-aimpoint-t2-mount-low","price":109.95,"options":{"mount":"black"},"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The page of MI-MK2-QDT2L (its text: \"SKU: MI-MK2-QDT2L MPN: MI-MK2-QDT2L\"), black, the one colour; its markup names no number (sku and mpn empty in its microdata)."}],"midwest-mk2-qd-t2-lower-13":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/midwest-industries-mk2-qd-aimpoint-t2-mount-lower-1-3-cowitness","price":129.95,"options":{"mount":"black"},"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The page of MI-MK2-QDT21-3 (its text: \"SKU: MI-MK2-QDT21-3 MPN: MI-MK2-QDT21/3\"), black, the one colour; its markup names no number (sku and mpn empty in its microdata)."}],"nordic-22rb-upper":[{"vendor":"nordic","url":"https://nordiccomp.com/categories/nc-22rb-upper/","price":658,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Nordic's page for the 16 in upper (\"22RB Dedicated 22 Upper-16\"); the 14.5 in has its own."},{"vendor":"aerospace-arms","url":"https://aerospacearms.com/nordic-components-22rb-complete-upper-22lr-16-match-grade-barrel-1-16-twist-black-finish/","price":549,"sku":"NC22RB-UPPER-16-KIT","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"alexanders","url":"https://alexandersstore.com/product/nordic-16-22lr-complete-upper-10rd/","price":581.99,"sku":"22RB-UPPER-16-KIT","in_stock":true,"observed":"2026-11-18","via":"harvest"}],"olight-baldr-s-bl":[{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/olight-baldr-s-bl-800-lumens-led-light-with-blue-dot","price":115.49,"options":{"body":"black"},"sku":"27224","in_stock":null,"observed":"2026-11-20","via":"harvest","note":"The seller's own number for the black light (its markup: \"115.49 USD ... sku=27224 ... - black\")."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/olight-baldr-s-bl-800-lumens-led-light-with-blue-dot","price":116.99,"options":{"body":"tan"},"sku":"27225","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"The seller's own number for the desert tan light (its markup: \"116.99 USD ... sku=27225 ... - desert-tan\")."}],"otter-creek-polonium-k":[{"vendor":"capitol-armory","url":"https://www.capitolarmory.com/otter-creek-labs-polonium-k-556-suppressor.html","price":539,"options":{"body":"black"},"sku":"OCL-POL556K","in_stock":false,"observed":"2026-11-09","via":"harvest"},{"vendor":"silencer-shop","url":"https://www.silencershop.com/otter-creek-labs-polonium-k.html","price":522,"sku":"OCL-POLK-MULTI","in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"kygunco","url":"https://www.kygunco.com/product/otter-creek-labs-polk-polonium-k","price":522,"options":{"body":"black"},"sku":"241963","in_stock":false,"observed":"2026-11-21","via":"harvest"}],"otter-creek-polonium":[{"vendor":"capitol-armory","url":"https://www.capitolarmory.com/otter-creek-labs-polonium-5-56-rifle-suppressor.html","price":549,"options":{"body":"black"},"sku":"OCL-POL556","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"silencer-shop","url":"https://www.silencershop.com/otter-creek-labs-polonium.html","price":532,"sku":"OCL-POL556-MULTI","in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"kygunco","url":"https://www.kygunco.com/product/otter-creek-labs-pol556-polonium-5.56","price":532,"options":{"body":"black"},"sku":"241961","in_stock":false,"observed":"2026-11-21","via":"harvest"}],"panzer-ar57-ult-12":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/ar57-ult-complete-upper-assembly-5-7-x28mm-12in","price":699.99,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The page is this one product (SKU AR57ULT-12 in its text); the markup names no number. \"50-round magazine included\"; the monobloc integrating \"barrel, muzzle brake, BCG, buffer, and screws\""},{"vendor":"kygunco","url":"https://www.kygunco.com/product/ar57-ar57ult-12-ult-5.7x28-12-upper-w-50rd-mag","price":711.85,"sku":"247149","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"KYGUNCO's own number in the markup. \"the bolt carrier group and a 50rd top feed magazine\""}],"panzer-ar57-ult-16":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/panzer-arms-ar57-ultra-light-tactical-5-7x28mm-complete-upper-16in","price":699.99,"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The page is this one product (SKU ULT0116 in its text); the markup names no number. \"This upper ships with a 50-round magazine.\"; \"Alloy monobloc receiver integrating barrel, BCG, buffer, and screws\""},{"vendor":"kygunco","url":"https://www.kygunco.com/product/ar57-ult-0116-ult-5.7x28-16-upper-w-50rd-mag","price":649.99,"sku":"247148","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"KYGUNCO's own number in the markup. \"It is supplied with the bolt carrier group and a 50rd top feed magazine\""}],"precision-armament-m4-72":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/precision-armament-m4-72-severe-duty-5-56-compensator-1-2x28-black","price":74.99,"options":{"body":"black"},"sku":"A04002","in_stock":true,"observed":"2026-11-01","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/a04002","price":89.99,"options":{"body":"black"},"sku":"A04002","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/a04003","price":89.99,"options":{"body":"stainless"},"sku":"A04003","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/precision-armament-m4-72-severe-duty-5-56-muzzle-brake/","price":89.99,"options":{"body":"black"},"sku":"7213","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"One page for both finishes, two offers in its markup by the seller's own numbers: 7213 \"- Black\", 7214 \"- Stainless\" (its mpn line: \"A04002,A04003\")."},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/precision-armament-m4-72-severe-duty-5-56-muzzle-brake/","price":89.99,"options":{"body":"stainless"},"sku":"7214","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/precision-armament-m4-72-severe-duty-5-56-muzzle-brake/","price":85.49,"options":{"body":"black"},"sku":"7213","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"One page for both finishes, two offers by the seller's own numbers: 7213 \"- black\", 7214 \"- stainless\"."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/precision-armament-m4-72-severe-duty-5-56-muzzle-brake/","price":85.49,"options":{"body":"stainless"},"sku":"7214","in_stock":null,"observed":"2026-11-21","via":"harvest"}],"primary-arms-deluxe-30mm-mount":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/primary-arms-deluxe-ar15-scope-mount-30mm-padlxsm","price":59.99,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The maker's own page (the page says SKU: PADLXSM, MPN: 910058); its offer markup names no number."},{"vendor":"kygunco","url":"https://kygunco.com/product/primary-arms-padlxsm-deluxe-ar15-scope-mount-30mm","price":59.99,"options":{"body":"black"},"sku":"123405","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"KYGUNCO's own number; its markup has mpn 910058 and gtin 818500010197."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/primary-arms-deluxe-ar-15-scope-mount-30mm/","price":59.99,"options":{"body":"black"},"sku":"8042","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"MPN PADLXSM and UPC 818500010197 in its Additional information; the page's own number is 8042."},{"vendor":"rifle-supply","url":"https://riflesupply.com/Primary-Arms-Deluxe-AR-15-Scope-Mount-30mm-910058_p_6732.html","price":63.99,"options":{"body":"black"},"sku":"6732","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Rifle Supply's own number; its markup has mpn 910058 and gtin12 818500010197."}],"primary-arms-slx-1-6x24-gen-iv":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/primary-arms-slx-1-6x24mm-sfp-rifle-scope-gen-4-illuminated-acss-nova-fiber-wire-reticle","price":349.99,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The maker's own page for this scope in black (the page says SKU: PA-SLX-1-6X24S-NOVA, MPN: 610183); its offer markup names no number."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/primary-arms-slx-1-6x24-sfp-rifle-scope-geniv-illuminated-acss-nova-fiber-wire-reticle-fde","price":299.99,"options":{"body":"fde"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The maker's own page for this scope in flat dark earth (the page says SKU: PA-SLX-1-6X24S-NOVA-FDE, MPN: 610207); its offer markup names no number."},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/primary-arms-slx-1-6x24-sfp-rifle-scope-gen-iv","price":349.99,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product: its only choices are the reticle 'ACSS NOVA' and the colour 'Black'. Its offer markup names no number."}],"primary-arms-slx-1-6x24-nova-deluxe-mount-kit":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/KIT-PA-SLX-1-6X24S-NOVA-PADLXSM","price":399.98,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The maker's own page for the kit (the page says SKU: KIT-PA-SLX-1-6X24S-NOVA-PADLXSM); its offer markup names no number."}],"primary-arms-slx-cantilever-30mm-mount":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/primary-arms-slx-cantilever-30mm-mount-1-5in","price":89.99,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The maker's own page for this mount (the page says SKU: PA-SLX-CM-30-1.5, MPN: 910105); its offer markup names no number."}],"psa-stealth-stripped-lower":[{"vendor":"palmetto-state-armory","url":"https://palmettostatearmory.com/psa-stealth-lower.html","price":79.99,"sku":"39296","in_stock":true,"observed":"2026-10-12","via":"user","note":"Palmetto State Armory's own page, as the user saved it from their browser on 2026-10-12: the site refuses the reader and is never asked (D59). Its markup names 39296 as SKU and MPN."}],"psa-stripped-upper":[{"vendor":"palmetto-state-armory","url":"https://palmettostatearmory.com/psa-ar-15-stripped-upper-receiver.html","price":69.99,"sku":"51655109407","in_stock":true,"observed":"2026-10-12","via":"user","note":"Palmetto State Armory's own page, as the user saved it from their browser on 2026-10-12: the site refuses the reader and is never asked (D59). Its markup names 51655109407 as SKU and MPN."}],"radian-raptor-charging-handle":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/radian-weapons-ar15-m16-raptor-ambidextrous-charging-handle-black","price":104.95,"options":{"latches":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product, black: 'SKU: R0001 MPN: R0001' in its text."},{"vendor":"kygunco","url":"https://www.kygunco.com/product/radian-weapons-r0001-raptor-ambidextrous-charging-handle-ar15-m16-blk","price":104.95,"options":{"latches":"black"},"sku":"131972","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Item # 131972, Style RDN-R0001, UPC 817093020477: the black one alone."},{"vendor":"sportsmans","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/gun-parts-magazines/rifle-parts/upper-receiver-parts/radian-raptor-ar15-ambidextrous-charging-handle/p/1464996","price":106.99,"options":{"latches":"black"},"sku":"1464996","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its markup: mpn R0001, sku 1464996, gtin12 817093020477, color Black."},{"vendor":"alexanders","url":"https://alexandersstore.com/product/radian-raptor-chrgng-hndl-556-blk/","price":104.95,"options":{"latches":"black"},"sku":"R0001","in_stock":true,"observed":"2026-11-18","via":"harvest","note":"Its markup: mpn R0001, gtin12 817093020477. Its 'Length 10.35 inches' is a package's."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/r0001","price":104.95,"options":{"latches":"black"},"sku":"R0001","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"One page for the colours, each under its number: 'SKU COLOR R0001 Black ... R0003 FDE R0005 NP3 ...'. The black one is R0001."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/radian-ar-15-m16-raptor-ambidextrous-charging-handle-flat-dark-earth","price":109.95,"options":{"latches":"fde"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product, Flat Dark Earth: 'SKU: R0003 MPN: R0003' in its text; its offer markup names no number."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/radian-raptor-charging-handle-ar15-radian-od","price":109.95,"options":{"latches":"od"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product, Radian OD: 'SKU: R0375 MPN: R0375' in its text; its offer markup names no number."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/radian-weapons-ar15-m16-raptor-ambidextrous-charging-handle-red","price":114.95,"options":{"latches":"red"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product, red: 'SKU: R0232 MPN: R0232' in its text; its offer markup names no number."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/radian-raptor-ambidextrous-ar15-charging-handle-np3","price":139.95,"options":{"latches":"np3"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product, NP3 coated: 'SKU: R0005 MPN: R0005' in its text; its offer markup names no number."},{"vendor":"alexanders","url":"https://alexandersstore.com/product/radian-raptor-chrgng-hnd-556-fde/","price":109.95,"options":{"latches":"fde"},"sku":"R0003","in_stock":true,"observed":"2026-11-18","via":"harvest","note":"Its markup: mpn R0003, gtin12 817093020521."},{"vendor":"alexanders","url":"https://alexandersstore.com/product/radian-raptor-charging-hndl-556-od/","price":109.95,"options":{"latches":"od"},"sku":"R0375","in_stock":true,"observed":"2026-11-18","via":"harvest","note":"Its markup: mpn R0375, gtin12 817093023584."},{"vendor":"alexanders","url":"https://alexandersstore.com/product/radian-weapons-raptor-charging-handle-grey/","price":109.95,"options":{"latches":"grey"},"sku":"R0560","in_stock":true,"observed":"2026-11-18","via":"harvest","note":"Its markup: mpn R0560, gtin12 817093022877: 'Radian Gray'."},{"vendor":"alexanders","url":"https://alexandersstore.com/product/radian-raptor-chrgng-hndl-556-red/","price":114.95,"options":{"latches":"red"},"sku":"R0232","in_stock":true,"observed":"2026-11-18","via":"harvest","note":"Its markup: mpn R0232, gtin12 817093021993."},{"vendor":"alexanders","url":"https://alexandersstore.com/product/radian-weapons-r0005-raptor-ambi-charging-handle-np3-coated-fits-mil-spec-ar-15-m16-platform/","price":139.95,"options":{"latches":"np3"},"sku":"R0005","in_stock":true,"observed":"2026-11-18","via":"harvest","note":"Its markup: mpn R0005, gtin12 817093020552."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/r0001","price":90.2,"options":{"latches":"tungsten"},"sku":"R0002","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"One page for the colours, each under its number: R0002 is Tungsten, which the page marks DISCONTINUED (its offer is out of stock)."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/r0001","price":109.95,"options":{"latches":"fde"},"sku":"R0003","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One page for the colours, each under its number: R0003 is FDE."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/r0001","price":139.95,"options":{"latches":"np3"},"sku":"R0005","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One page for the colours, each under its number: R0005 is NP3 Nickel."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/r0001","price":109.95,"options":{"latches":"od"},"sku":"R0375","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One page for the colours, each under its number: R0375 is Radian OD."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/r0001","price":109.95,"options":{"latches":"grey"},"sku":"R0560","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One page for the colours, each under its number: R0560 is Radian Grey."},{"vendor":"rifle-supply","url":"https://riflesupply.com/Radian-Raptor-Charging-Handle-AR15-Platform-Brown-R0004_p_262.html","price":132.99,"options":{"latches":"brown"},"sku":"262","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The seller's own number, which the markup carries (mpn R0004, gtin12 817093020545)."},{"vendor":"wing-tactical","url":"https://www.wingtactical.com/firearm-parts-accessories/ar-15-parts/ar-15-upper-receiver-parts/charging-handles/radian-competition-raptor-ar-15-ambidextrous-charging-handle/","price":104.95,"options":{"latches":"red"},"sku":"RW-R0232","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Wing Tactical's page for the Competition Raptor: 'MPN: R0232', the red one's number."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/radian-raptor-ambidextrous-charging-handle/","price":104.95,"options":{"latches":"black"},"sku":"1769","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"The seller's own number for its 'black' variant, which the markup carries. Its 'grey' variant (1777) is left out: its picture and its price are the NP3 handle's, and the page doesn't say which grey it is. The 'clear-anodized' offer (8282) remains excluded: its identity has not been verified against the current maker R0140 identity; Clear Ano remains unavailable until its appearance is verified."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/radian-raptor-ambidextrous-charging-handle/","price":109.95,"options":{"latches":"fde"},"sku":"1770","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"The seller's own number for its 'fde' variant, which the markup carries. Its 'grey' variant (1777) is left out: its picture and its price are the NP3 handle's, and the page doesn't say which grey it is. The 'clear-anodized' offer (8282) remains excluded: its identity has not been verified against the current maker R0140 identity; Clear Ano remains unavailable until its appearance is verified."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/radian-raptor-ambidextrous-charging-handle/","price":109.95,"options":{"latches":"od"},"sku":"8281","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"The seller's own number for its 'od-green' variant, which the markup carries. Its 'grey' variant (1777) is left out: its picture and its price are the NP3 handle's, and the page doesn't say which grey it is. The 'clear-anodized' offer (8282) remains excluded: its identity has not been verified against the current maker R0140 identity; Clear Ano remains unavailable until its appearance is verified."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/radian-raptor-ambidextrous-charging-handle/","price":109.95,"options":{"latches":"brown"},"sku":"7644","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"The seller's own number for its 'brown' variant, which the markup carries. Its 'grey' variant (1777) is left out: its picture and its price are the NP3 handle's, and the page doesn't say which grey it is. The 'clear-anodized' offer (8282) remains excluded: its identity has not been verified against the current maker R0140 identity; Clear Ano remains unavailable until its appearance is verified."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/radian-raptor-ambidextrous-charging-handle/","price":94.95,"options":{"latches":"tungsten"},"sku":"3693","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"The seller's own number for its 'tungsten' variant, which the markup carries. Its 'grey' variant (1777) is left out: its picture and its price are the NP3 handle's, and the page doesn't say which grey it is. The 'clear-anodized' offer (8282) remains excluded: its identity has not been verified against the current maker R0140 identity; Clear Ano remains unavailable until its appearance is verified."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/radian-raptor-competition-ambidextrous-charging-handle-556-red/","price":114.95,"options":{"latches":"red"},"sku":"3692","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"The seller's own number for the red Competition Raptor, which the markup carries."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/radian-raptor-competition-ambidextrous-charging-handle-556-red/","price":114.95,"options":{"latches":"blue"},"sku":"3712","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"The seller's own number for the blue Competition Raptor, which the markup carries."}],"radian-raptor-lt-charging-handle":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/radian-raptor-lt-ambidextrous-ar15-charging-handle-black","price":79.95,"options":{"latches":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product, black: 'SKU: R0148 MPN: R0148' in its text; its offer markup names no number."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/radian-raptor-lt-ambidextrous-ar-15-charging-handle","price":84.95,"options":{"latches":"fde"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product, Flat Dark Earth: 'SKU: R0149 MPN: R0149' in its text; its offer markup names no number."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/radian-raptor-lt-ambidextrous-ar15-charging-handle-gray","price":84.95,"options":{"latches":"grey"},"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product, grey: 'SKU: R0150 MPN: R0150' in its text; its offer markup names no number."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/raptor-lt-ar15","price":79.95,"options":{"latches":"black"},"sku":"R0148","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"One page for the three colours, each under its number: 'SKU COLOR R0148 Black R0149 FDE R0150 Stealth Grey'. R0148 is Black."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/raptor-lt-ar15","price":84.95,"options":{"latches":"fde"},"sku":"R0149","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One page for the three colours, each under its number: 'SKU COLOR R0148 Black R0149 FDE R0150 Stealth Grey'. R0149 is FDE."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/raptor-lt-ar15","price":84.95,"options":{"latches":"grey"},"sku":"R0150","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One page for the three colours, each under its number: 'SKU COLOR R0148 Black R0149 FDE R0150 Stealth Grey'. R0150 is Stealth Grey."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/radian-raptor-lt-ambidextrous-charging-handle-556-black/","price":79.95,"options":{"latches":"black"},"sku":"1771","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"The seller's own number for its 'black' variant, which the markup carries (one page for the three colours)."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/radian-raptor-lt-ambidextrous-charging-handle-556-black/","price":84.95,"options":{"latches":"fde"},"sku":"3688","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"The seller's own number for its 'fde' variant, which the markup carries (one page for the three colours)."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/radian-raptor-lt-ambidextrous-charging-handle-556-black/","price":84.95,"options":{"latches":"grey"},"sku":"1778","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"The seller's own number for its 'grey' variant, which the markup carries (one page for the three colours)."},{"vendor":"impact-guns","url":"https://www.impactguns.com/ar-15-upper-receiver-parts/radian-raptor-lt-ambidextrous-charging-handle-ar15-m16-black-817093021160-r0148","price":79.95,"options":{"latches":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product, black: 'SKU: 817093021160 ... Manufacturer Number: R0148' in its text; its offer markup names no number."},{"vendor":"impact-guns","url":"https://www.impactguns.com/ar-15-upper-receiver-parts/radian-raptor-lt-ambidextrous-charging-handle-ar15-m16-fde-817093021177-r0149","price":84.95,"options":{"latches":"fde"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product, Flat Dark Earth: its address ends -fde-817093021177-r0149 (the colour, the UPC, the number); its offer markup names no number."},{"vendor":"impact-guns","url":"https://www.impactguns.com/ar-15-upper-receiver-parts/radian-raptor-lt-ambidextrous-charging-handle-ar15-m16-stealth-grey-817093021184-r0150","price":84.95,"options":{"latches":"grey"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product, which it calls Stealth Grey: its address ends -stealth-grey-817093021184-r0150 (the colour, the UPC, the number); its offer markup names no number."},{"vendor":"sportsmans","url":"https://sportsmans.com/shooting-gear-gun-supplies/gun-parts-magazines/gun-components/radian-raptor-lt-ar15m16-charging-handle/p/1474832","price":74.99,"options":{"latches":"black"},"sku":"1474832","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Its markup: mpn R0148, sku 1474832, gtin12 817093021160, color Black."},{"vendor":"right-to-bear","url":"https://www.righttobear.com/radian-raptor-lt-ambi-charging-tungsten-grey-r0150/","price":84.95,"options":{"latches":"grey"},"sku":"R0150","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is the grey one alone, which it calls Tungsten Grey: 'Product Code: R0150', the number its markup carries (upc 817093021184)."},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/1019310582","price":79.95,"options":{"latches":"black"},"sku":"591811","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One page for the three colours; the seller's own number for 'Radian Raptor-LT AR-15 Ambidextrous Charging Handle Black', which the markup carries with the colour's UPC as its mpn (817093021160)."},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/1019310582","price":84.95,"options":{"latches":"fde"},"sku":"653913","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One page for the three colours; the seller's own number for '... Flat Dark Earth', which the markup carries with the colour's UPC as its mpn (817093021177)."},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/1019310582","price":84.95,"options":{"latches":"grey"},"sku":"853969","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One page for the three colours; the seller's own number for '... Gray', which the markup carries with the colour's UPC as its mpn (817093021184)."},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/Radian-Weapons-Raptor-Charging-Handle/","price":79.95,"options":{"latches":"black"},"sku":"652597","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"T.REX ARMS' page for the whole Raptor family; the seller's own number for 'Radian Raptor Ambidextrous Charging Handle - LT, Black', which the markup carries."},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/Radian-Weapons-Raptor-Charging-Handle/","price":84.95,"options":{"latches":"fde"},"sku":"1332783","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"T.REX ARMS' page for the whole Raptor family; the seller's own number for 'Radian Raptor Ambidextrous Charging Handle - LT, FDE', which the markup carries."}],"radian-raptor-sd-charging-handle":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/radian-raptor-sd-ambidextrous-vented-ar-15-charging-handle-black","price":134.95,"options":{"latches":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product, black: 'SKU: R0006 MPN: R0006' in its text; its offer markup names no number."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/radian-raptor-sd-vented-ambidextrous-ar15-charging-handle-fde","price":139.95,"options":{"latches":"fde"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product, Flat Dark Earth: 'SKU: R0066 MPN: R0066' in its text; its offer markup names no number."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/radian-raptor-sd-ar-15-charging-handle-radian-od","price":139.95,"options":{"latches":"od"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product, Radian OD: 'SKU: R0376 MPN: R0376' in its text; its offer markup names no number."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/raptor-sd-ar15","price":134.95,"options":{"latches":"black"},"sku":"R0006","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One page for the colours, each under its number: 'SKU COLOR R0006 Black R0066 FDE R0376 Radian OD R0561 Radian Grey'."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/raptor-sd-ar15","price":139.95,"options":{"latches":"fde"},"sku":"R0066","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/raptor-sd-ar15","price":139.95,"options":{"latches":"od"},"sku":"R0376","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/raptor-sd-ar15","price":139.95,"options":{"latches":"grey"},"sku":"R0561","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/radian-raptor-ambidextrous-charging-handle-472185","price":134.95,"options":{"latches":"black"},"sku":"472186","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One page for the family; its markup's variant 'Radian Raptor Ambidextrous Charging Handle - SD, Black'."},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/radian-raptor-ambidextrous-charging-handle-472185","price":139.95,"options":{"latches":"fde"},"sku":"1332785","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its markup's variant 'Radian Raptor Ambidextrous Charging Handle - SD, FDE'."},{"vendor":"alexanders","url":"https://alexandersstore.com/product/radian-raptor-sd-chrgng-hndl-556-blk/","price":134.95,"options":{"latches":"black"},"sku":"R0006","in_stock":true,"observed":"2026-11-18","via":"harvest","note":"Its markup: mpn R0006 (no sku), gtin12 817093020491. Its 'Length: 10.45 in' is a package's."},{"vendor":"alexanders","url":"https://alexandersstore.com/product/radian-raptor-sd-chrgng-hndl-556-gry/","price":139.95,"options":{"latches":"grey"},"sku":"R0561","in_stock":false,"observed":"2026-11-18","via":"harvest","note":"Its markup: mpn R0561 (no sku), gtin12 817093025441, 'Color / Finish: Radian Grey'."},{"vendor":"alexanders","url":"https://alexandersstore.com/product/radian-raptor-sd-chrgng-hndl-556-od/","price":139.95,"options":{"latches":"od"},"sku":"R0376","in_stock":true,"observed":"2026-11-18","via":"harvest","note":"Its markup: mpn R0376 (no sku), gtin12 817093023591, 'OD Green Cerakote over MIL-SPEC Type III Hard Coat Anodize'."},{"vendor":"kygunco","url":"https://www.kygunco.com/product/radian-weapons-r0006-raptor-sd-ambidextrous-charging-handle-ar15-m16","price":134.95,"options":{"latches":"black"},"sku":"131975","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Item # 131975, Style RDN-R0006, UPC 817093020491: the black one alone."},{"vendor":"kygunco","url":"https://www.kygunco.com/product/radian-weapons-r0065-raptor-sd-ambi-charging-handle-ar15-m16-grey","price":155.72,"options":{"latches":"tungsten"},"sku":"131976","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Item # 131976, Style RDN-R0065: 'RAPTOR-SD AMBIDEXTROUS CHARGING HANDLE: TUNGSTEN GREY' (out of stock when read)."},{"vendor":"sportsmans","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/gun-parts-magazines/rifle-parts/upper-receiver-parts/radian-raptor-sd-ar15-ambidextrous-charging-handle/p/1464998","price":134.99,"options":{"latches":"black"},"sku":"1464998","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its markup: mpn R0006, sku 1464998, gtin12 817093020491, color Black."},{"vendor":"rifle-supply","url":"https://riflesupply.com/radian-raptor-sd-chrgng-hndl-556-blk/","price":134.99,"options":{"latches":"black"},"sku":"DSHIP-RWR0006","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Its markup: mpn R0006 (a drop-ship listing)."},{"vendor":"impact-guns","url":"https://www.impactguns.com/parts/radian-raptor-sd-ambidextrous-charging-handle-ar15-m16-black-anodized-817093020491-r0006","price":134.95,"options":{"latches":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product, black R0006 (UPC 817093020491 in its address); its offer markup names no number."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/radian-raptor-sd-ambidextrous-charging-handle/","price":134.95,"options":{"latches":"black"},"sku":"3702","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"One page for the colours; its markup's variant '... - black'."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/radian-raptor-sd-ambidextrous-charging-handle/","price":139.95,"options":{"latches":"fde"},"sku":"3704","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Its markup's variant '... - fde'."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/radian-raptor-sd-ambidextrous-charging-handle/","price":129.95,"options":{"latches":"tungsten"},"sku":"3703","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"Its markup's variant '... - tungsten-grey'."}],"radian-talon-safety-selector":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/radian-weapons-talon-ambidextrous-safety-selector-2-lever-kit-r0018","price":64.95,"options":{"levers":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product, black: 'SKU: R0018 MPN: R0018' in its text; its offer markup names no number, and says the one price twice."},{"vendor":"right-to-bear","url":"https://www.righttobear.com/radian-talon-ambi-safety-selector-2-lever-kit-r0018/","price":64.95,"options":{"levers":"black"},"sku":"R0018","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"rifle-supply","url":"https://riflesupply.com/Radian-Talon-Ambi-Safety-Selector-2-Lever-Kit-Black-R0018_p_2167.html","price":66.99,"options":{"levers":"black"},"sku":"2167","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The markup's sku is the seller's own number; its mpn is R0018."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/talon-2-lever","price":64.95,"options":{"levers":"black"},"sku":"R0018","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/talon-2-lever","price":69.95,"options":{"levers":"fde"},"sku":"R0020","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/talon-2-lever","price":69.95,"options":{"levers":"od"},"sku":"R0381","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/talon-2-lever","price":69.95,"options":{"levers":"grey"},"sku":"R0567","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/radian-talon-ambidextrous-45-90-2-lever-safety-selector/","price":64.95,"options":{"levers":"black"},"sku":"3727","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"The seller's own number for its black variant (the markup's '- black')."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/radian-talon-ambidextrous-45-90-2-lever-safety-selector/","price":69.95,"options":{"levers":"fde"},"sku":"3728","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"The seller's own number for its FDE variant."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/radian-talon-ambidextrous-45-90-2-lever-safety-selector/","price":69.95,"options":{"levers":"od"},"sku":"8283","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"The seller's own number for its OD green variant (R0381 is in its list of numbers; its UPC list has 817093023645, which MidwayUSA sells as Olive Drab)."},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/1086195127125","price":64.95,"options":{"levers":"black"},"sku":"378621","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Matte Black; the markup's mpn is the UPC 817093020514, R0018's."},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/1086195127125","price":69.95,"options":{"levers":"fde"},"sku":"127125","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Flat Dark Earth; the markup's mpn is the UPC 817093020668."},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/1086195127125","price":69.95,"options":{"levers":"od"},"sku":"447921","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Olive Drab; the markup's mpn is the UPC 817093023645."}],"reptilia-aus-30mm-mount":[{"vendor":"kygunco","url":"https://www.kygunco.com/product/reptilia-aus-mount-30mm-black-1.54-bore-height","price":292.46,"options":{"body":"black"},"sku":"272274","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its markup: sku 272274, mpn 100-116, gtin 850022282133."},{"vendor":"sportsmans","url":"https://www.sportsmans.com/hunting-gear-supplies/optics-binoculars-scopes-rangefinders/scope-rings-bases/reptilia-aus-mount-30mm-154in-bore-height-anodized-black/p/1818958","price":324.99,"options":{"body":"black"},"sku":"1818958","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its markup: sku 1818958, mpn 100-116."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/reptilia-corp-aus-30mm-1-54-optic-mount/","price":292.46,"options":{"body":"black"},"sku":"8802","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"One page for both colours, a number each in its markup: 8802 'black', 8803 'fde' (the maker's 100-116 and 100-122 are in its Additional information)."},{"vendor":"kygunco","url":"https://www.kygunco.com/product/reptilia-aus-mount-30mm-fde-1.54-bore-height","price":292.46,"options":{"body":"fde"},"sku":"272277","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its markup: sku 272277, mpn 100-122. (FDE offered since 2026-10-19, with a photograph of it on file: 0bf480654d9e.)"},{"vendor":"rifle-supply","url":"https://riflesupply.com/reptilia-aus-30mm-mount-optic-mount-1-54-bore-height-fde-100-122/","price":292.99,"options":{"body":"fde"},"sku":"8218","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Its markup: sku 8218, mpn 100-122."},{"vendor":"gritr-sports","url":"https://gritrsports.com/reptilia-aus-30mm-mount-1-54-fde","price":292.46,"options":{"body":"fde"},"sku":"REPT-100-122","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its markup: sku REPT-100-122, mpn 100-122 (twice, one price; a third offer on the page is another product's)."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/reptilia-corp-aus-30mm-1-54-optic-mount/","price":292.46,"options":{"body":"fde"},"sku":"8803","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"The page the black's 8802 is on: its markup's 'fde' offer."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/reptilia-corp-aus-30mm-optic-mount-black-1.54in","price":299.66,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product in black (its text: SKU: 100-116 MPN: 100-116); the markup names no number, and states the one price twice."}],"reptilia-dot-mount-193":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/reptilia-corp-dot-mount-aimpoint-micro-black-1.93in","price":112.46,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of the black 1.93 alone (its title and its specification table: Color Black, Mount Height 1.93 in.); its markup names no number (microdata, two offers at one price)."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/reptilia-corp-dot-mount-aimpoint-micro-fde-1.93in","price":112.46,"options":{"body":"fde"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of the flat dark earth 1.93 alone; its markup names no number (microdata, two offers at one price)."},{"vendor":"rifle-supply","url":"https://riflesupply.com/Reptilia-DOT-Mount-193-Height-Fits-Aimpoint-Micro-Black-100-037_p_6467.html","price":107.99,"options":{"body":"black"},"sku":"6467","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its markup: sku 6467, mpn 100-037."},{"vendor":"rifle-supply","url":"https://riflesupply.com/reptilia-dot-mount-1-93-optical-axis-height-fits-aimpoint-micro-anodized-black-100-037","price":112.99,"options":{"body":"black"},"sku":"DSHIP-REP100-037","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Rifle Supply's second listing of the black 1.93 (drop-shipped): its markup, sku DSHIP-REP100-037, mpn 100-037; out of stock on 2026-11-03."},{"vendor":"rifle-supply","url":"https://riflesupply.com/Reptilia-DOT-Mount-193-Height-Fits-Aimpoint-Micro-FDE-100-038_p_6468.html","price":107.99,"options":{"body":"fde"},"sku":"6468","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its markup: sku 6468, mpn 100-038."},{"vendor":"sportsmans","url":"https://www.sportsmans.com/hunting-gear-supplies/optics-binoculars-scopes-rangefinders/scope-rings-bases/reptillia-dot-mount-193in-optical-axis-height-aimpoint-micro-anodized-flat-dark-earth/p/1818944","price":109.99,"options":{"body":"fde"},"sku":"1818944","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its markup: sku 1818944, mpn 100-038."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/reptilia-corp-dot-mount-for-aimpoint-micro","price":98.96,"options":{"body":"black"},"sku":"7071","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"One page for both heights and both colours, a number each in its markup: 7071 '1-93 / black', 7072 '1-93 / fde', 7069 '1-5 / black', 7070 '1-5 / fde'."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/reptilia-corp-dot-mount-for-aimpoint-micro","price":98.96,"options":{"body":"fde"},"sku":"7072","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"The same page: 7072 '1-93 / fde'."}],"reptilia-dot-mount-39mm":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/Reptilia-corp-dot-mount-aimpoint-micro-fde-lower-1-3rd","price":112.46,"options":{"body":"fde"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of the flat dark earth lower 1/3 alone (its title; Primary Arms' own number R100-024 is in its text, not its markup): its markup names no number (microdata, two offers at one price)."},{"vendor":"rifle-supply","url":"https://riflesupply.com/Reptilia-DOT-Mount-Fits-Aimpoint-Micro-Black-100-004_p_6465.html","price":89.99,"options":{"body":"black"},"sku":"6465","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Its markup: sku 6465, mpn 100-004; out of stock on 2026-11-03."},{"vendor":"rifle-supply","url":"https://riflesupply.com/Reptilia-DOT-Mount-Fits-Aimpoint-Micro-FDE-100-024_p_6466.html","price":92.99,"options":{"body":"fde"},"sku":"6466","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its markup: sku 6466, mpn 100-024."},{"vendor":"sportsmans","url":"https://www.sportsmans.com/hunting-gear-supplies/optics-binoculars-scopes-rangefinders/scope-rings-bases/reptillia-dot-mount-lower-13-co-witness-base-anodized-black/p/1818921","price":94.99,"options":{"body":"black"},"sku":"1818921","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Its markup: sku 1818921, mpn 100-004 (its title names no dot and its table says \"Height Style High\"; the number is this part's). Out of stock on 2026-11-03."},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/1023010579/","price":112.46,"options":{"body":"black"},"sku":"361111","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One page for both colours, a number each in its markup: 361111 'Aluminum Black' (mpn 850002688085, the black's UPC), 894055 'Aluminum Flat Dark Earth' (850002688245, the FDE's)."},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/1023010579/","price":112.46,"options":{"body":"fde"},"sku":"894055","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The same page: 894055 'Aluminum Flat Dark Earth'."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/reptilia-corp-dot-mount-for-aimpoint-micro","price":85.46,"options":{"body":"black"},"sku":"7069","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"One page for both heights and both colours, a number each in its markup: 7069 '1-5 / black', 7070 '1-5 / fde' (the lower 1/3, which the page calls 1.5 in)."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/reptilia-corp-dot-mount-for-aimpoint-micro","price":98.96,"options":{"body":"fde"},"sku":"7070","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"The same page: 7070 '1-5 / fde'."}],"rise-lpk":[{"vendor":"right-to-bear","url":"https://www.righttobear.com/rise-armament-ar15-lower-parts-kit/","price":44.99,"sku":"12003","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"redcon1","url":"https://redcon1tactical.com/rise-armament-ar-15-lower-parts-kit.html","price":44.99,"sku":"12003","in_stock":true,"observed":"2026-11-21","via":"harvest"}],"rosco-bloodline-105-barrel":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/rosco-manufacturing-bloodline-556-barrel-government-carbine-10.5","price":144.9,"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (the number is in its text: SKU and MPN BL-105-M4-556-7-C); the markup names no number"},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/1024526582?pid=244017","price":144.9,"sku":"244017","in_stock":true,"observed":"2026-10-30","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/rosco-manufacturing-bloodline-10-5-5-56-m4-17-twist-black-nitride-cabine-barrel/","price":134.95,"sku":"4639","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/rosco-manufacturing-bloodline-10-5-5-56-m4-17-twist-black-nitride-cabine-barrel/","price":132.3,"sku":"4639","in_stock":false,"observed":"2026-11-21","via":"harvest"}],"rosco-bloodline-115-barrel":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/rosco-manufacturing-bloodline-556-barrel-government-carbine-11.5","price":150.3,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (the number is in its text: SKU and MPN BL-115-M4-556-7-C); the markup names no number"},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/1024526582?pid=638416","price":150.3,"sku":"638416","in_stock":true,"observed":"2026-10-30","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/rosco-manufacturing-bloodline-11-5-5-56-m4-17-twist-black-nitride-cabine-barrel/","price":144.95,"sku":"4640","in_stock":false,"observed":"2026-11-21","via":"harvest"}],"rosco-bloodline-125-barrel":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/rosco-manufacturing-bloodline-556-barrel-government-carbine-12.5","price":154.8,"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (the number is in its text: SKU and MPN BL-125-M4-556-7-C); the markup names no number"},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/1024526582?pid=407128","price":154.8,"sku":"407128","in_stock":true,"observed":"2026-10-30","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/rosco-manufacturing-bloodline-12-5-5-56-m4-17-twist-black-nitride-carbine-barrel/","price":149.95,"sku":"4641","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"rifle-supply","url":"https://riflesupply.com/rosco-manufacturing-bloodline-ar-15-12-5-barrel-barrel-12-5-barrel-5-56-nato-black-bl-125-m4-556-7-c/","price":129.99,"sku":"8665","in_stock":false,"observed":"2026-11-21","via":"harvest"}],"sb-tactical-sba3":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/sb-tactical-sba3-ar-pistol-stabilizing-brace-black-no-buffer-tube","price":69.99,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product in black (the page says SKU: SBA3X-01-SB, MPN: SBA3X-01-SB); its offer markup names no number."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/sba3-xx","price":99.99,"options":{"body":"black"},"sku":"SBA3-BLK","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The shop's code SBA3-XX, under the older numbers SBA3-BLK and SBA3-FDE: the markup's own."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/sba3-xx","price":99.99,"options":{"body":"fde"},"sku":"SBA3-FDE","in_stock":true,"observed":"2026-11-21","via":"harvest"}],"sb-tactical-sba4":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/sb-tactical-sba4-pistol-stabilizing-brace-black-no-buffer-tube","price":69.99,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product in black (the page says SKU: SBA4X-01-SB, MPN: SBA4X-01-SB); its offer markup names no number."},{"vendor":"gritr-sports","url":"https://gritrsports.com/sb-tactical-sba4-5-position-arm-brace-sba4x-01-sb","price":68.99,"options":{"body":"black"},"sku":"SBT-SBA4X-01-SB","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"wing-tactical","url":"https://www.wingtactical.com/firearm-parts-accessories/sb-tactical-sba4-pistol-stabilizing-brace/","price":99.99,"sku":"SBT-SBA4X","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One offer for the product, its colour chosen on the page (\"Finish: Black, Flat Dark Earth, or OD Green\"): no colour named."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/sb-tactical-sba4x-brace-only/","price":99.99,"options":{"body":"black"},"sku":"4083","in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/sb-tactical-sba4x-brace-only/","price":99.99,"options":{"body":"fde"},"sku":"6112","in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/sb-tactical-sba4x-brace-only/","price":99.99,"options":{"body":"odg"},"sku":"10851","in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/sb-tactical-sba4x-brace-only/","price":99.99,"options":{"body":"stealth_gray"},"sku":"10852","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"The page's 'grey' (its markup: 'SB Tactical SBA4X Brace Only - grey'), the Stealth Gray brace."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/sb-tactical-sba4-pistol-stabilizing-brace-stealth-grey-no-buffer-tube","price":49.99,"options":{"body":"stealth_gray"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product in Stealth Gray (the page says SKU: SBA4X-03M-SB, MPN: SBA4X-03M-SB); its offer markup names no number."}],"sb-tactical-sba5":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/sb-tactical-sba5-ar-pistol-stabilizing-brace-black","price":69.99,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product in black (the page says SKU: SBA5-BLK, MPN: SBA5-BLK); its offer markup names no number."},{"vendor":"gritr-sports","url":"https://gritrsports.com/sb-tactical-sba5-pistol-stabilizing-brace-sba5x-01-sb","price":67.99,"options":{"body":"black"},"sku":"SBT-SBA5X-01-SB","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"kygunco","url":"https://www.kygunco.com/product/sb-tactical-sba5x-01-sb-sba5-blk-5-position-adjustable","price":99.99,"options":{"body":"black"},"sku":"252331","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"wing-tactical","url":"https://www.wingtactical.com/firearm-parts-accessories/ar-15-parts/ar-15-buffer-systems/ar-15-buffer-tube-accessories/sb-tactical-sba5-pistol-stabilizing-brace/","price":99.99,"sku":"SBT-SBA5X","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One offer for the product, its colour chosen on the page (\"Color: (Required) Choose Options Black Flat Dark Earth\"): no colour named."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/sb-tactical-sba5-brace-only/","price":65.95,"options":{"body":"black"},"sku":"24268","in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/sb-tactical-sba5-brace-only/","price":99.99,"options":{"body":"fde"},"sku":"24269","in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/sb-tactical-sba5-brace-only/","price":99.99,"options":{"body":"odg"},"sku":"31045","in_stock":null,"observed":"2026-11-21","via":"harvest"}],"sb-tactical-sbpdw":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/sb-tactical-pdw-adjustable-pistol-stabilizing-brace-black","price":199.99,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (the page: SKU SBTPDW-01-SB, MPN PDW-01-SB); its offer markup names no number (2026-10-18)."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/sb-tactical-sbpdw-pistol-stabilizing-brace-ar-black/","price":239.99,"sku":"2673","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"right-to-bear","url":"https://www.righttobear.com/sb-tactical-pdw-pistol-stabilizing-brace-pdw-01-sb/","price":300,"sku":"PDW-01-SB","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"gritr-sports","url":"https://gritrsports.com/sb-tactical-pdw-ar-pistol-brace-pdw-01-sb","price":209.99,"sku":"SBT-PDW-01-SB","in_stock":true,"observed":"2026-11-21","via":"harvest"}],"scalarworks-leap-01-micro-142":[{"vendor":"scalarworks","url":"https://scalarworks.com/shop/quick-detach-mounts/leap-01/","price":159,"options":{"mount":"black"},"sku":"SW0100","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The maker's own shop: one page for the three heights, its markup an offer for each by its number (this one out of stock on 2026-11-03)."},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/scalarworks-leap-01-aimpoint-micro-t-2-qd-mount-73479","price":159,"options":{"mount":"black"},"sku":"113132","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"T.REX ARMS: one page for the three heights; its markup's offer for 1.42 in by its own number (out of stock on 2026-11-03)."}],"scalarworks-leap-01-micro-157":[{"vendor":"scalarworks","url":"https://scalarworks.com/shop/quick-detach-mounts/leap-01/","price":159,"options":{"mount":"black"},"sku":"SW0110","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The maker's own shop: one page for the three heights, its markup an offer for each by its number."},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/scalarworks-leap-01-aimpoint-micro-t-2-qd-mount-73479","price":159,"options":{"mount":"black"},"sku":"113131","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"T.REX ARMS: one page for the three heights; its markup's offer for 1.57 in by its own number."},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/1022884560","price":159,"options":{"mount":"black"},"sku":"100599","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"MidwayUSA: one page for 1.57 and 1.93 in; its markup's offer for 1.57 in, \"Matte Black\"."}],"scalarworks-leap-01-micro-193":[{"vendor":"scalarworks","url":"https://scalarworks.com/shop/quick-detach-mounts/leap-01/","price":159,"options":{"mount":"black"},"sku":"SW0120","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The maker's own shop: one page for the three heights, its markup an offer for each by its number."},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/scalarworks-leap-01-aimpoint-micro-t-2-qd-mount-73479","price":159,"options":{"mount":"black"},"sku":"148276","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"T.REX ARMS: one page for the three heights; its markup's offer for 1.93 in by its own number."},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/1022884560","price":159,"options":{"mount":"black"},"sku":"361961","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"MidwayUSA: one page for 1.57 and 1.93 in; its markup's offer for 1.93 in, \"Matte Black\"."}],"scalarworks-leap-02-micro-226":[{"vendor":"scalarworks","url":"https://scalarworks.com/shop/quick-detach-mounts/leap-02/","price":179,"options":{"mount":"black"},"sku":"SW0230","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The maker's own shop: its markup an offer for each colour by its number (out of stock on 2026-11-03)."},{"vendor":"scalarworks","url":"https://scalarworks.com/shop/quick-detach-mounts/leap-02/","price":189,"options":{"mount":"fde"},"sku":"SW0230-FDE","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The maker's own shop: its markup's offer for flat dark earth by its number (out of stock on 2026-11-03)."}],"scalarworks-leap-08-30mm-mount":[{"vendor":"scalarworks","url":"https://scalarworks.com/shop/quick-detach-mounts/leap-08/","price":419,"options":{"body":"black"},"sku":"SW0815","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The maker's own shop: one page for both heights, its markup an offer for each by its number."}],"sig-alpha-msr-30mm":[{"vendor":"gritr","url":"https://gritroutdoors.com/sig-sauer-alpha-msr-30mm-scope-mount-soa20016","price":71.99,"options":{"body":"coyote"},"sku":"SOA20016","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"gritr","url":"https://gritroutdoors.com/sig-sauer-alpha-msr-30mm-black-scope-mount-soa20014","price":68.57,"options":{"body":"black"},"sku":"SOA20014","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/sig-sauer-alpha-msr-scope-mount-30mm-1-535-0-moa-6061-t6-black/","price":74.99,"options":{"body":"black"},"sku":"20404","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"MPN SOA20014 in its Additional information; the page's own number is 20404."}],"sig-romeo-msr-gen-2-kit":[{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/sig-sauer-romeo-msr-gen-ii-1x20mm-2-moa-compact-red-dot-black/","price":129.99,"options":{"body":"black"},"sku":"SORMSR101","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/sig-sauer-romeo-msr-gen-ii-1x20-mm-reflex-red-dot-sight/","price":129.99,"options":{"body":"black"},"sku":"SORMSR101","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"impact-guns","url":"https://www.impactguns.com/reflex-sights/sig-romeo-msr-gen-2-red-dot-1x20mm-black-798681694624-sormsr101","price":111.99,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"SORMSR101 by its page's title and address; its markup names no number"},{"vendor":"right-to-bear","url":"https://www.righttobear.com/sig-sauer-romeo-msr-gen-ii-2-moa-red-dot-sight/","price":134.95,"options":{"body":"black"},"sku":"SORMSR101","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"scheels","url":"https://www.scheels.com/p/sig-sauer-romeo-msr-gen-ii-red-dot/1701-SORMSR101/","price":129.99,"options":{"body":"black"},"sku":"79868169462","in_stock":true,"observed":"2026-10-06","via":"harvest","note":"Scheels' own number in the markup; the page's address says SORMSR101"},{"vendor":"sportsmans","url":"https://www.sportsmans.com/hunting-gear-supplies/optics-binoculars-scopes-rangefinders/red-dots/sig-sauer-romeo-msr-gen-ii-1x-20mm-red-dot-2-moa/p/1873391","price":103.49,"options":{"body":"black"},"sku":"1873391","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"alexanders","url":"https://alexandersstore.com/product/sig-romeo-msr-gen-ii-red-dot-blk/","price":107.99,"options":{"body":"black"},"sku":"SORMSR101","in_stock":true,"observed":"2026-11-18","via":"harvest"},{"vendor":"alexanders","url":"https://alexandersstore.com/product/sig-sauer-romeo-msr-gen2-1x20mm-fde/","price":106.99,"options":{"body":"fde"},"sku":"SORMSR111","in_stock":true,"observed":"2026-11-18","via":"harvest"},{"vendor":"sportsmans","url":"https://www.sportsmans.com/hunting-gear-supplies/optics-binoculars-scopes-rangefinders/red-dots/sig-sauer-romeo-msr-gen-ii-1x20mm-fde-red-dot-2-moa-dot/p/1939082","price":119.99,"options":{"body":"fde"},"sku":"1939082","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Sportsman's own number, which its markup carries (mpn SORMSR111)"}],"sig-romeo5-gen-ii-kit":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/sig-sauer-romeo-5-gen-ii-2-moa-red-dot-sight","price":149.99,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"SOR5101 by its page's own line, \"SKU: SOR5101 MPN: SOR5101\"; its markup names no number"},{"vendor":"sportsmans","url":"https://www.sportsmans.com/hunting-gear-supplies/optics-binoculars-scopes-rangefinders/red-dots/sig-sauer-romeo5-gen-ii-1x-red-dot-2-moa-dot/p/1900437","price":116.99,"options":{"body":"black"},"sku":"1900437","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"impact-guns","url":"https://www.impactguns.com/reflex-sights/sig-sauer-romeo-5-gen-ii-red-dot-sight-1x20mm-black-2-moa-dot-for-picatinny-798681694600-sor5101","price":135.99,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"SOR5101 by its page's title and address; its markup names no number"},{"vendor":"alexanders","url":"https://alexandersstore.com/product/sig-romeo5-gii-red-dot-1x20mm-2moa/","price":125.99,"options":{"body":"black"},"sku":"SOR5101","in_stock":true,"observed":"2026-11-18","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/sig-sauer-romeo5-gen-ii-1x20-1-moa-red-dot-sight/","price":149.99,"options":{"body":"black"},"sku":"25160","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"scheels","url":"https://www.scheels.com/p/sig-sauer-romeo-5-gen-ii-1x20mm-2-moa-red-dot-sight/1701-SOR5101.html","price":139.99,"options":{"body":"black"},"sku":"79868169460","in_stock":true,"observed":"2026-10-19","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/sor5101","price":129.34,"options":{"body":"black"},"sku":"SOR5101","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/sor5111","price":134.19,"options":{"body":"fde"},"sku":"SOR5111","in_stock":false,"observed":"2026-11-18","via":"harvest"},{"vendor":"alexanders","url":"https://alexandersstore.com/product/sig-romeo5-gii-2-moa-red-dot-fde/","price":134.99,"options":{"body":"fde"},"sku":"SOR5111","in_stock":true,"observed":"2026-11-18","via":"harvest"}],"sig-tango-msr-1-6x24-kit":[{"vendor":"sportsmans","url":"https://www.sportsmans.com/hunting-gear-supplies/optics-binoculars-scopes-rangefinders/rifle-scopes-red-dots/sig-sauer-tango-msr-lpvo-1-6x-24mm-rifle-scope-bdc6/p/1696951","price":269.99,"options":{"body":"black"},"sku":"SOT61000","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"alexanders","url":"https://alexandersstore.com/product/sig-tango-msr-1-6x24-msr-bdc6/","price":244.99,"options":{"body":"black"},"sku":"SOT61000","in_stock":true,"observed":"2026-11-18","via":"harvest"},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/sig-sauer-tango-msr-scope-1-6x24mm-30mm-sfp-illuminated-msr-bdc6-reticle-0-5-moa-capped-turret-black-w-1-535-mount/","price":279.99,"options":{"body":"black"},"sku":"SOT61000","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"gritr","url":"https://gritroutdoors.com/sig-sauer-tango-msr-lpvo-coyote-riflescope-sotm61200","price":259.99,"options":{"body":"coyote"},"sku":"SOTM61200","in_stock":true,"observed":"2026-11-21","via":"harvest"}],"silencerco-sparrow-22":[{"vendor":"silencer-shop","url":"https://www.silencershop.com/silencerco-sparrow-22.html","price":296,"sku":"SCO SU75","in_stock":null,"observed":"2026-11-21","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/silencerco-sparrow-22-caliber-silencer-black","price":296.65,"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Primary Arms' page for this one product (SU75); its markup named that number until October 2026 and names none since"},{"vendor":"kygunco","url":"https://www.kygunco.com/product/100482","price":296.65,"sku":"SU75","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"capitol-armory","url":"https://www.capitolarmory.com/silencerco-ss-sparrow-22-rimfire-suppressor.html","price":349,"sku":"SU75","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"scheels","url":"https://www.scheels.com/p/silencerco-sparrow-22-rimfire-suppressor/817272-SU75","price":299.99,"sku":"81727201000","in_stock":true,"observed":"2026-10-01","via":"harvest"}],"slr-sentry-7-gas-block":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/slr-rifleworks-sentry-7-set-screw-adjustable-gas-block-.750","price":148.99,"options":{"body":"melonite"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (SKU and MPN SA7-SM in its text); its offer markup names no number (make offers show, 2026-10-28: two offers, both 124.99 USD)"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/slr-rifleworks-sentry-adjustable-gas-block-set-screw/","price":141.64,"options":{"body":"melonite"},"sku":"22605","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"One page for six variants; the markup's 22605 is \"0-75 / melonite\", the .750 Melonite block (the page's list of numbers has SA7-SM for it, and no .450 one)"},{"vendor":"slr-rifleworks","url":"https://slrrifleworks.com/sentry-7-set-screw-adjustable-gas-block/","price":118.19,"options":{"body":"melonite"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"SLR's own page for the .750 set-screw block (its title: 'Sentry .750\" Set Screw Version - Melonite QPQ Finish .400\" Set Screw Spacing'); its markup names no number (make offers show, 2026-10-28: two microdata offers, both 126.06 USD in stock)."}],"spikes-tactical-sdr100a":[{"vendor":"spikes-tactical","url":"https://www.spikestactical.com/collections/parts/delta-ring-assembly-w-mil-spec-barrel-nut/","price":18.95,"sku":"SDR100A","in_stock":null,"observed":"2026-11-21","via":"harvest"}],"streamlight-protac-rail-mount-hl-x":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/streamlight-protac-rail-mount-hl-x-1000-lumen-weapon-light-tapeswitch","price":119.99,"fitment":"cr123a","sku":"88066","in_stock":true,"observed":"2026-11-17","via":"harvest"},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/1018571930/","price":133.44,"fitment":"cr123a","sku":"951275","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"MidwayUSA's own number in the markup; 88066 by its page"},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/102958235","price":143.64,"fitment":"sl_b26","sku":"667967","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"MidwayUSA's own number in the markup; 88071 by its page"},{"vendor":"sportsmans","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/gun-parts-accessories/gun-parts-magazines/weapon-lights/streamlight-protac-rail-mount-hl-x-gun-light/p/1470378","price":143.99,"fitment":"cr123a","sku":"88066","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"sportsmans","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/gun-parts-accessories/gun-parts-magazines/weapon-lights/streamlight-protac-rail-mount-hl-x-long-gun-light-black/p/1821926","price":134.97,"fitment":"sl_b26","sku":"88071","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"mile-high","url":"https://www.milehighshooting.com/streamlight-protac-rail-mount-hl-x-long-gun-light/","price":182.99,"fitment":"sl_b26","sku":"88071","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"impact-guns","url":"https://www.impactguns.com/Lights/STREAMLIGHT-ProTac-HL-X-Dual-Fuel-WML-Light-1-000-Lumens-080926880665-88066/","price":147.99,"fitment":"cr123a","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"88066 by its page's title and address; its markup names no number"},{"vendor":"alexanders","url":"https://alexandersstore.com/product/strmlght-protac-hl-x-rail-mount/","price":140.99,"fitment":"cr123a","sku":"88066","in_stock":true,"observed":"2026-11-18","via":"harvest"},{"vendor":"gritr","url":"https://gritroutdoors.com/streamlight-protac-rail-mount-weapon-light-88066","price":148.43,"fitment":"cr123a","sku":"88066","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"gritr","url":"https://gritroutdoors.com/streamlight-protac-rail-mount-hl-x-usb-long-gun-light-88071","price":162.99,"fitment":"sl_b26","sku":"88071","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"rifle-supply","url":"https://riflesupply.com/Streamlight-ProTac-HL-X-Rail-Mount-Remote-Pressure-Switch-88066_p_1975.html","price":136.99,"fitment":"cr123a","sku":"88066","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/streamlight-protac-railmount-hl-x-weapon-light-1000-lumen-black/","price":145,"fitment":"cr123a","sku":"5470","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"AR15Discounts' own number in the markup; 88066 by its page"}],"superlative-750-gas-block":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/superlative-arms-bleed-off-adjustable-gas-block-set-screw-750-melonite","price":89.99,"options":{"body":"melonite"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its page is this one product (SKU and MPN SABO-DI-750SM in its text); its offer markup names no number (make offers show, 2026-10-06)"},{"vendor":"right-to-bear","url":"https://www.righttobear.com/superlative-arms-750-adjustable-gas-block-bleed-sabo-di-750sm/","price":94.95,"options":{"body":"melonite"},"sku":"SABO-DI-750SM","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/superlative-arms-750-adjustable-gas-block-solid-melonited/","price":94.99,"options":{"body":"melonite"},"sku":"2549","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"2549 is the shop's own number in its markup, with the maker's as mpn (SABO-DI-750SM) and gtin 850011846063"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/superlative-arms-750-adjustable-gas-block-solid-melonited/","price":89.99,"options":{"body":"melonite"},"sku":"2549","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The same page and number as Dirty Bird's"},{"vendor":"right-to-bear","url":"https://www.righttobear.com/superlative-arms-750-adjustable-gas-block-bleed-sabo-di-750ss/","price":94.95,"options":{"body":"stainless"},"sku":"SABO-DI-750SS","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/superlative-arms-750-adjustable-gas-block-solid-stainless-steel/","price":89.99,"options":{"body":"stainless"},"sku":"2550","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"2550 is the shop's own number in its markup, with the maker's as mpn (SABO-DI-750SS)"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/superlative-arms-750-adjustable-gas-block-solid-stainless-steel/","price":89.99,"options":{"body":"stainless"},"sku":"2550","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The same page and number as Dirty Bird's (its own markup names no mpn)"}],"surefire-m340c-mini-scout-light-pro":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/surefire-m340c-mini-scout-light-pro-weapon-light-500-lumens-black","price":269.99,"options":{"body":"black"},"sku":"M340C-BK-PRO","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of the black light alone (\"SKU: M340C-BK-PRO\" in its text) whose markup names no number."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/surefire-m340c-mini-scout-light-pro-weapon-light-500-lumens-tan","price":269.99,"options":{"body":"tan"},"sku":"M340C-TN-PRO","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of the tan light alone (\"SKU: M340C-TN-PRO\" in its text) whose markup names no number."},{"vendor":"mile-high","url":"https://www.milehighshooting.com/surefire-mini-scout-light-pro-3-volt-scout-light-pro-w-z68-tailcap/","price":341,"options":{"body":"black"},"sku":"M340C-BK-PRO","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/1022376924","price":341,"options":{"body":"black"},"sku":"465384","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The family page's black offer (its mpn is the black light's UPC, 084871329224)."},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/1022376924","price":341,"options":{"body":"tan"},"sku":"756745","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The family page's tan offer (its mpn is the tan light's UPC, 084871329231)."},{"vendor":"impact-guns","url":"https://www.impactguns.com/weapon-mounted-lights/surefire-m340c-scout-pro-flashlight-black-1913-picatinny-mount-084871329224-m340c-bk-pro","price":341,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of the black light alone (its address carries M340C-BK-PRO and its UPC) whose markup names no number."},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/SureFire-M340C-Mini-Scout-Light-PRO/","price":341,"options":{"body":"black"},"sku":"664627","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/SureFire-M340C-Mini-Scout-Light-PRO/","price":341,"options":{"body":"tan"},"sku":"664628","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"sportsmans","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/gun-parts-accessories/gun-parts-magazines/weapon-lights/surefire-mini-scout-light-pro-with-z68-tailcap-weaponlight/p/1705233","price":341,"options":{"body":"black"},"sku":"1705233","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its one offer's mpn is M340C-BK-PRO."}],"surefire-procomp-556":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/surefire-procomp-muzzle-brake-1-2x28-procomp556-1-2-28","price":74.99,"sku":"PROCOMP556-1-2-28","in_stock":true,"observed":"2026-11-17","via":"harvest"},{"vendor":"rifle-supply","url":"https://riflesupply.com/surefire-procomp-mb-5-56mm-1-2x28/","price":76.99,"sku":"DSHIP-SFPROCOMP-556-12-28","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"mile-high","url":"https://www.milehighshooting.com/surefire-procomp-556-1-2-28-non-suppressor-adapter-muzzle-brake-for-5-56-with-1-2-28-threading/","price":89,"sku":"PROCOMP-556-1/2-28","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/PROCOMP-556-12-28","price":89,"sku":"PROCOMP-556-12-28","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"kygunco","url":"https://www.kygunco.com/product/surefire-procomp-556-1-2-28-procomp-556-muzzle-break-1-2x28-black","price":89,"sku":"163062","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"impact-guns","url":"https://www.impactguns.com/other-parts/surefire-procomp-muzzle-brake-stand-alone-model-adapter-5-56mm-1-2-28-tpi-black-084871323512-procomp-556-1-2-28/","price":89,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (its address carries the UPC 084871323512 and PROCOMP-556-1-2-28); its markup names no number, and carries the one price twice."},{"vendor":"sportsmans","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/gun-parts-accessories/gun-parts-magazines/rifle-parts/muzzle-brakes-devices/surefire-procomp-556-12-28-muzzle-break/p/1663701","price":99.99,"sku":"1663701","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"alexanders","url":"https://alexandersstore.com/product/surefire-procomp-mb-5-56mm-1-2x28/","price":89,"sku":"PROCOMP-556-1/2-28","in_stock":false,"observed":"2026-11-18","via":"harvest","note":"A page of this one product (mpn PROCOMP-556-1/2-28 in its markup); its markup names no number."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/surefire-procomp-muzzle-brake-5-56-1-2x28/","price":89,"sku":"4683","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"redcon1","url":"https://redcon1tactical.com/ar-15/magazines/followers/surefire-procomp-muzzle-brake-5-56-black.html?category_id=230","price":89,"sku":"PROCOMP-556-1/2-28","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (mpn PROCOMP-556-1/2-28 in its markup); its markup names no number."},{"vendor":"cheaper-than-dirt","url":"https://www.cheaperthandirt.com/surefire-procomp-556-muzzle-brake-5.56-nato.223-rem-threaded-12x28-heat-treated-stainless-steel-black-melonite-finish-procomp-556-12-28/FC-084871323512.html","price":89,"sku":"PROCOMP556","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (mpn PROCOMP556 in its markup, PROCOMP-556-1/2-28 in its title); its markup names no number."}],"surefire-scout-light-pro-dual-fuel":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/surefire-m640df-scout-light-pro-dual-fuel-weapon-light-1500-lumens-black","price":269.99,"options":{"body":"black"},"sku":"M640DF-BK-PRO","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/1022377344?pid=722487","price":341,"options":{"body":"black"},"sku":"722487","in_stock":true,"observed":"2026-10-30","via":"harvest"},{"vendor":"mile-high","url":"https://www.milehighshooting.com/surefire-scout-light-pro-dual-fuel-black/","price":341,"options":{"body":"black"},"sku":"M640DF-BK-PRO","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"alexanders","url":"https://alexandersstore.com/product/surefire-m640df-scout-pro-1500lm-bk/","price":341,"options":{"body":"black"},"sku":"M640DF-BK-PRO","in_stock":true,"observed":"2026-11-18","via":"harvest"},{"vendor":"rifle-supply","url":"https://riflesupply.com/Surefire-M640DF-Scout-Pro-LED-Flashlight-Flashlight-1500-Lumens-1913-Picatinny-Mount-Rechargeable-Battery-Black-M640DF-BK-PRO_p_7278.html","price":349.99,"options":{"body":"black"},"sku":"7278","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"scheels","url":"https://www.scheels.com/p/surefire-dual-fuel-scout-light-pro-led-weaponlight/084871-M640DF.html/","price":332,"options":{"body":"black"},"sku":"08487132926","in_stock":true,"observed":"2026-10-05","via":"harvest"},{"vendor":"sportsmans","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/gun-parts-accessories/gun-parts-magazines/weapon-lights/surefire-dual-fuel-scout-light-pro-with-z68-tailcap-weaponlight/p/1705234","price":341,"options":{"body":"black"},"sku":"1705234","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"kygunco","url":"https://www.kygunco.com/product/surefire-m640df-bk-pro-m640df-scout-pro-flashlight-1500-lumen-m-lok","price":341,"options":{"body":"black"},"sku":"216047","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"alexanders","url":"https://alexandersstore.com/product/surefire-m640df-scout-pro-1500lm-tn/","price":395,"options":{"body":"tan"},"sku":"M640DF-TN-PRO","in_stock":true,"observed":"2026-11-18","via":"harvest"},{"vendor":"rifle-supply","url":"https://riflesupply.com/surefire-m640df-scout-pro-1500lm-tn/","price":395.99,"options":{"body":"tan"},"sku":"M640DF-TN-PRO","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"sportsmans","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/gun-parts-accessories/gun-parts-magazines/weapon-lights/surefire-scout-light-pro-duel-fuel-weapon-light-tan/p/1896633","price":395,"options":{"body":"tan"},"sku":"M640DF-TN-PRO","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/m640df-tn-pro","price":395,"options":{"body":"tan"},"sku":"M640DF-TN-PRO","in_stock":true,"observed":"2026-11-21","via":"harvest"}],"surefire-socom-3-prong":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/surefire-3-prong-flash-hider-silencer-mount-sf3p-556-1-2-28","price":152,"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (SKU SF3P-556-1-2-28, MPN SF3P-556-1/2-28 in its text); its markup names no number."},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/surefire-socom-flash-hider-1357594","price":152,"sku":"909276","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One page for the family; the markup's 909276 is \"SureFire SOCOM Flash Hider - 3-Prong, 5.56mm (.223 Caliber), 1/2-28\"."},{"vendor":"midwayusa","url":"https://www.midwayusa.com/product/1016579424","price":152,"sku":"369900","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The markup's 369900 carries mpn 084871319119, the UPC SureFire's page gives for SF3P-556-1/2-28."}],"surefire-socom-4-prong":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/surefire-socom-4-prong-5-56-flash-hider-suppressor-adapter-1-2x28","price":179,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product; its markup names no number."},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/surefire-socom-flash-hider-1357594","price":180,"sku":"1342505","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One page for the family; the markup's 1342505 is \"SureFire SOCOM Flash Hider - 4-Prong, 5.56mm (.223 Caliber), 1/2-28\"."},{"vendor":"silencer-shop","url":"https://www.silencershop.com/surefire-4-prong-flash-hider.html","price":179,"sku":"SUREFIRE FH556RC-1/2-28","in_stock":null,"observed":"2026-11-21","via":"harvest"}],"surefire-socom556-rc2":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/surefire-socom-2-qd-sound-suppressor-socom556-rc2-bk","price":1196,"options":{"body":"black"},"sku":"SOCOM556-RC2-BK","in_stock":true,"observed":"2026-11-17","via":"harvest"},{"vendor":"primary-arms","url":"https://www.primaryarms.com/surefire-socom-2-qd-sound-suppressor-socom556-rc2-de","price":1196,"options":{"body":"dark-earth"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The page of the Dark Earth one alone (SKU and MPN SOCOM556-RC2-DE in its text); its markup names no number, and carries the one price twice."},{"vendor":"silencer-shop","url":"https://www.silencershop.com/surefire-socom556-rc2-1.html","price":1196,"options":{"body":"black"},"sku":"sf_socom556_rc2","in_stock":null,"observed":"2026-11-21","via":"harvest","note":"The seller's own number for the product. The page opens on the black one (SUREFIRE SOCOM556-RC2-BK, Color Black) and names Dark Earth as its other colour: its markup has one offer, taken as the black one's."},{"vendor":"capitol-armory","url":"https://www.capitolarmory.com/surefire-socom-556rc2-suppressor.html","price":1289,"sku":"SF-SOCOM556-RC2","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The seller's own number, one offer for the product: the page lists Black and Dark Earth (FDE) and gives no price apart for either."},{"vendor":"impact-guns","url":"https://www.impactguns.com/Suppressors/SureFire-2nd-Gen-SOCOM-5-56-Black-Incl-SFMB-556-1-2-28-084871324564-SOCOM556-RC2-BK/","price":1196,"options":{"body":"black"},"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The page of the black one alone (MPN SOCOM556-RC2-BK, UPC 084871324564 in its address); its markup names no number, and carries the one price twice. Its address says 'Incl SFMB-556-1-2-28' and the page says nothing of a muzzle brake coming with it."},{"vendor":"impact-guns","url":"https://www.impactguns.com/Suppressors/Surefire-Socom-Gen-2-RC2-5-56mm-Suppressor-Dark-Earth-Quick-Detach-084871324571-SOCOM556-RC2-DE/","price":1196,"options":{"body":"dark-earth"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The page of the Dark Earth one alone (SOCOM556-RC2-DE, UPC 084871324571 in its address); its markup names no number, and carries the one price twice."},{"vendor":"kygunco","url":"https://www.kygunco.com/product/surefire-socom556-rc2-bk-socom-g2-5.56-suppressor-blk","price":1196,"options":{"body":"black"},"sku":"423","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The seller's own number in the markup (its mpn there is SOCOM556-RC2-BK)."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/SOCOM556-RC2-BK","price":1196,"options":{"body":"black"},"sku":"SOCOM556-RC2-BK","in_stock":true,"observed":"2026-11-21","via":"harvest"}],"surefire-warcomp":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/surefire-warcomp-556-warcomp-556-1-2-28","price":152,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product; its markup names no number."},{"vendor":"trex-arms","url":"https://www.trex-arms.com/store/surefire-warcomp-flash-hider/","price":152,"sku":"909391","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"One page for the three-prong and the Closed Tine; the markup's 909391 is \"SureFire WARCOMP Flash Hider - 3-Prong, 5.56mm (.223 Caliber), 1/2-28\"."},{"vendor":"mile-high","url":"https://www.milehighshooting.com/surefire-warcomp-556-1-2x28-adapter-for-556-socom-suppressors/","price":152,"sku":"WARCOMP-556-1/2-28","in_stock":true,"observed":"2026-11-21","via":"harvest"}],"sylvan-arms-sa5-pro-left-folder":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/https-www.primaryarms.com-sylvan-arms-ar-15-ar-9-folding-stock-adapter-gen-5-left-folding","price":189.99,"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The page is for SA5P-L alone; its markup names no number (two microdata offers, one price)."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/sylvan-arms-ar-15-ar-9-folding-stock-adapter-gen-5-left-folding/","price":189.99,"sku":"30716","in_stock":false,"observed":"2026-11-21","via":"harvest"}],"sylvan-arms-sa5-pro-right-folder":[{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/sylvan-arms-ar-15-ar-9-folding-stock-adapter-gen-5-right-folding/","price":189.99,"sku":"30715","in_stock":false,"observed":"2026-11-21","via":"harvest"}],"taurus-tx22-magazine-16":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/taurus-tx22lr-magazine-16-round","price":24.99,"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The page's markup names no number; the page is of this one product (Taurus TX22 .22LR 16-round magazine)."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/358-0017-01","price":26.75,"sku":"358-0017-01","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"kygunco","url":"https://www.kygunco.com/product/taurus-358-0017-01-tx22-22lr-16rd-poly-black-magazine","price":21.16,"sku":"140003","in_stock":true,"observed":"2026-11-21","via":"harvest"}],"taurus-tx22-magazine-22":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/taurus-tx22-22-lr-22rd-magazine","price":29.99,"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"The page's markup names no number; the page is of this one product (Taurus TX22 .22 LR 22-round magazine)."},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/358-0034-00","price":32.95,"sku":"358-0034-00","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"kygunco","url":"https://www.kygunco.com/product/taurus-tx22-22rd-magazine","price":26.99,"sku":"258267","in_stock":true,"observed":"2026-11-21","via":"harvest"}],"taurus-tx22-toro":[{"vendor":"sportsmans","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/handguns/taurus-tx22-gen-2-toro-22-long-rifle-46in-hard-anodized-black-pistol-221-rounds/p/1883977","price":319.99,"sku":"1883977","in_stock":false,"observed":"2026-11-21","via":"harvest"}],"toolcraft-556-bcg":[{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/toolcraft-223-5-56-300blk-m16-profile-bolt-carrier-group-black-nitride/","price":109.95,"sku":"2705","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"dirty-bird","url":"https://dirtybirdusa.com/products/toolcraft-223-5-56-300-blk-m16-profile-bolt-carrier-group-black-nitride/","price":119.95,"sku":"2705","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"right-to-bear","url":"https://www.righttobear.com/toolcraft-black-nitride-mpi-m16-bcg-tooauto-016/","price":142.95,"sku":"TOOAUTO-016","in_stock":false,"observed":"2026-11-21","via":"harvest"}],"unity-fast-micro-226":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/unity-tactical-fast-ap-micro-mount-black","price":186,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Primary Arms' page for the black one, FST-MICB by its title and its SKU and MPN in the page's text (its markup names no number: two offers of one price)."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/unity-tactical-fast-aimpoint-micro-mount-fde","price":186,"options":{"body":"fde"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Primary Arms' page for the flat dark earth one, FST-MICF by its title and its SKU and MPN in the page's text (its markup names no number: two offers of one price)."},{"vendor":"mile-high","url":"https://www.milehighshooting.com/unity-tactical-fast-micro-red-dot-mount-2-26/","price":186,"options":{"body":"black"},"sku":"FST-MICB","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/unity-fast-t1t2","price":195,"options":{"body":"black"},"sku":"FST-MICB","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"midwest-gun-works","url":"https://www.midwestgunworks.com/page/mgwi/prod/unity-fast-t1t2","price":195,"options":{"body":"fde"},"sku":"FST-MICF","in_stock":true,"observed":"2026-11-21","via":"harvest"},{"vendor":"rifle-supply","url":"https://riflesupply.com/Unity-Tactical-FAST-Micro-Red-Dot-Mount-Optic-Mount-226-Optical-Height-T1T2-Footprints-FDE-FST-MICF_p_7679.html","price":195.99,"options":{"body":"fde"},"sku":"7679","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"Rifle Supply's page for the FDE, FST-MICF (its MPN in the markup; its own number 7679)."}],"vg6-gamma-556":[{"vendor":"aero-precision","url":"https://www.aeroprecisionusa.com/vg6-gamma-556","price":90,"in_stock":null,"observed":"2026-11-21","via":"harvest","note":"The maker's shop, a page of this one product (\"SKU: APVG200001A\" in its text); its markup names no number."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/vg6-precision-gamma-5-56-high-performance-muzzle-brake-1-2x28-gen-2","price":80.99,"in_stock":false,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (SKU and MPN APVG200001A in its text); its markup names no number, and carries the one price twice."},{"vendor":"rifle-supply","url":"https://riflesupply.com/VG6-Gamma-556-Muzzle-Device-556-NATO-Black-APVG200001A_p_3557.html","price":90.99,"sku":"3557","in_stock":false,"observed":"2026-11-21","via":"harvest"},{"vendor":"wing-tactical","url":"https://www.wingtactical.com/firearm-parts/ar-15-parts/muzzle-devices/vg6-precision-gamma-556-muzzle-brake/","price":80.99,"sku":"VG6-GAMMA-556","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"Its text names two numbers and two finishes (\"APVG200001A / APVG200010A\", \"Blacknitride or Bead Blasted Stainless\"); its markup has one offer, VG6-GAMMA-556, at one price."},{"vendor":"aerospace-arms","url":"https://aerospacearms.com/aero-precision-vg6-gamma-556-muzzle-brake-223-rem-556nato-black-1-2x28/","price":80.99,"sku":"APVG200001A","in_stock":false,"observed":"2026-11-19","via":"harvest"},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/vg6-gamma-556/","price":72.99,"sku":"1588","in_stock":false,"observed":"2026-11-21","via":"harvest"}],"vltor-a5-buffer-kit":[{"vendor":"vltor","url":"https://vltor.com/products/re-a5-and-sp-a5","price":182.9,"sku":"RE-A5 and SP-A5","in_stock":false,"observed":"2026-11-21","via":"harvest"}],"vltor-a5-buffer-spring":[{"vendor":"vltor","url":"https://vltor.com/products/v2-1174-c102","price":12.95,"sku":"V2-1174-C102","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"VLTOR's own shop; its json-ld names V2-1174-C102 (make offers show, 2026-10-28)."}],"vltor-a5-receiver-extension":[{"vendor":"vltor","url":"https://vltor.com/products/re-a5","price":62.95,"sku":"RE-A5","in_stock":false,"observed":"2026-11-21","via":"harvest","note":"VLTOR's own shop; its json-ld names RE-A5 (make offers show, 2026-10-28)."},{"vendor":"primary-arms","url":"https://www.primaryarms.com/vltor-re-a5-a5-receiver-extension-re-a5","price":56.66,"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The page is for VLTOR's RE-A5 alone (\"SKU: RE-A5 MPN: RE-A5\" in its text, \"7-position A5-length buffer tube\"); its markup names no number (two microdata offers, one price, out of stock on 2026-10-28)."}],"vltor-a5h2-buffer":[{"vendor":"vltor","url":"https://vltor.com/products/a5h2","price":95.95,"sku":"A5H2","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"VLTOR's own shop; its json-ld names A5H2 (make offers show, 2026-10-28)."}],"vltor-castle-nut":[{"vendor":"vltor","url":"https://vltor.com/products/v2-1069-m3","price":5.95,"sku":"V2-1069-M3","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"VLTOR's own shop; its json-ld names V2-1069-M3 (make offers show, 2026-10-28)."}],"vltor-lockplate":[{"vendor":"vltor","url":"https://vltor.com/products/v2-1069-m1","price":5.95,"sku":"V2-1069-M1","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"VLTOR's own shop; its json-ld names V2-1069-M1 (make offers show, 2026-10-28)."}],"vltor-sp-a5":[{"vendor":"vltor","url":"https://www.vltor.com/products/sp-a5","price":119.95,"sku":"SP-A5","in_stock":true,"observed":"2026-11-21","via":"harvest"}],"vortex-sport-cantilever-30mm-mount":[{"vendor":"primary-arms","url":"https://www.primaryarms.com/vortex-optics-30mm-sport-cantilever-mount-1-5in-height","price":119.99,"options":{"body":"black"},"in_stock":true,"observed":"2026-11-21","via":"harvest","note":"A page of this one product (SKU and MPN SCM-30-150 in its text); its markup names no number: two offers, both $119.99."},{"vendor":"kygunco","url":"https://www.kygunco.com/product/vortex-sports-cantilever-mount-30mm-1.5-height","price":119.99,"options":{"body":"black"},"sku":"281508","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The markup's sku is the shop's item number; its mpn is SCM-30-150."},{"vendor":"scheels","url":"https://www.scheels.com/p/875874-SCM-30-150","price":119.99,"options":{"body":"black"},"sku":"84382914048","in_stock":true,"observed":"2026-10-13","via":"harvest","note":"The markup's sku and mpn are the shop's own number (the UPC less its last digit); the page's number is 875874-SCM-30-150."},{"vendor":"sportsmans","url":"https://www.sportsmans.com/hunting-gear-supplies/optics-binoculars-scopes-rangefinders/scope-rings-bases/vortex-optics-sport-30mm-cantilever-mount-matte-black-1-piece/p/1932637","price":119.99,"options":{"body":"black"},"sku":"1932637","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The markup's sku is the shop's item number; its mpn is SCM-30-150."},{"vendor":"ar15discounts","url":"https://ar15discounts.com/products/vortex-30mm-1-5-sport-cantilever-mount/","price":119.99,"options":{"body":"black"},"sku":"25847","in_stock":true,"observed":"2026-11-21","via":"harvest","note":"The markup's sku is the shop's own; the page's MPN is SCM-30-150."}]},"cartridges":{"5.56 NATO":{"label":"5.56×45 mm NATO"},".22 LR":{"label":".22 Long Rifle"},".22 WMR":{"label":".22 Winchester Magnum Rimfire"},".22 Hornet":{"label":".22 Hornet"},".17 HMR":{"label":".17 Hornady Magnum Rimfire"},".17 WSM":{"label":".17 Winchester Super Magnum"},"5.7x28mm":{"label":"5.7×28 mm"},".223 Rem":{"label":".223 Remington"},".300 Blackout":{"label":".300 Blackout"}},"kits":{"aero-m4e1-complete-upper-16-mid-r-one-15":{"id":"aero-m4e1-complete-upper-16-mid-r-one-15","label":"Complete upper","name":"M4E1 Threaded complete upper, 16\" 5.56 mid-length, 15\" R-ONE M-LOK","manufacturer":"Aero Precision","sku":"APAR700705M7","url":"https://www.aeroprecisionusa.com/m4e1-threaded-complete-upper-16-5-56-mid-barrel-atlas-r-one-15-m-lok-hg-anodized","platform":"ar15","alsoOn":[],"contains":{"upper_receiver":{"part":"aero-m4e1-threaded-upper","fitment":"assembled","stated":"M4E1 Threaded Assembled Upper Receiver - Anodized Black","note":"The assembled receiver, APAR700201AC: \"Port Door and Forward Assist installed\" (its own page)."},"barrel":{"part":"aero-556-16-mid-barrel","stated":"16\" 5.56 CMV Barrel; 16\" 5.56 Mid-Length Barrel Features: 5.56 NATO 16\" Midlength, 1/7 twist, 4150 CrMoV, QPQ, gas port drilled .750 gas block journal Mid-length gas system, .0785 gas port M4 Feed Ramp Extension HP and MPI tested Standard A2 flash hider","note":"No number given; every figure is APBA100060C's page's."},"handguard":{"part":"aero-r-one-15-handguard","stated":"15\" R-ONE M-LOK Handguard; Finish: Anodized Black"},"gas_block":{"part":"aero-750-gas-block","stated":"Low Profile Gas Block; .750 gas block journal","note":"No number, logo or finish given: Aero sells the .750 low-profile block with its logo (this one) and without. Under the handguard either way."},"gas_tube":{"part":"aero-mid-gas-tube","stated":"Mid-Length Gas Tube","note":"Its material isn't given: Aero sells a stainless mid-length tube (this one) and a Melonite one."},"muzzle":{"part":"a2-flash-hider","stated":"Standard A2 flash hider","note":"Among the barrel's features, not the Includes list; its maker isn't named."}},"mounted":[],"also":[],"description":"Aero's M4E1 Threaded complete upper with a 16 in 5.56 mid-length CMV barrel under the 15 in R-ONE, sold assembled. \"This complete upper does not include BCG or Charging Handle\": its page offers Aero's as add-ons, the catalog's two."},"aimpoint-duty-rds-kit":{"id":"aimpoint-duty-rds-kit","label":"Red dot on its mount","name":"Duty RDS Red Dot Sight - One-piece Torsion Nut Mount, 39mm","manufacturer":"Aimpoint","sku":"200759","url":"https://bravocompanyusa.com/aimpoint-duty-rds-red-dot-sight-one-piece-torsion-nut-mount-39mm/","platform":"ar15","alsoOn":[],"contains":{},"mounted":[{"part":"aimpoint-duty-rds-39mm-mount","stated":"1x Torsion nut mount and spacer (39mm)","note":"T.REX ARMS' list of what is in the box."},{"part":"aimpoint-duty-rds","stated":"1x Duty RDS Red Dot Reflex Sight","note":"T.REX ARMS' list of what is in the box. Drawn on the mount where Aimpoint's own profiles of 200759 have it."}],"also":["a CR2032 battery and a T10 wrench (T.REX ARMS' list)"],"description":"Aimpoint's Duty RDS as an AR-15 takes it: the sight on its one-piece torsion nut mount, its axis 39 mm over the rail. The mount goes on the rail and the sight on it, by the Micro footprint."},"aimpoint-micro-t-2-kit":{"id":"aimpoint-micro-t-2-kit","label":"Red dot on its mount","name":"Micro T-2 Red Dot Reflex Sight - AR15 Ready","manufacturer":"Aimpoint","sku":"200198","url":"https://bravocompanyusa.com/micro-t-2-2-moa-red-dot-reflex-sight-with-39-mm-spacer-lrp-mount/","platform":"ar15","alsoOn":[],"contains":{},"mounted":[{"part":"aimpoint-micro-lrp-39mm","stated":"This AR15 Ready version includes 39 mm Spacer and LRP (Lever Release Picatinny) Mount","note":"Aimpoint's sheet for 200198; Bravo Company: \"The AR15 Ready configuration includes a 39mm spacer and LRP (Lever Release Picatinny) base\"."},{"part":"aimpoint-micro-t-2","stated":"Aimpoint 200198 Micro T-2 Red Dot Sight 2 MOA Dot AR-15 Ready with 39mm Spacer and LRP Mount","note":"Atlantic Tactical's name for the listing (in the sight's seed). Drawn on the spacer where Aimpoint's own profiles of 200198 have it."}],"also":["flip-up lens covers, drawn with the sight (Bravo Company: \"Flip-up lens covers – front is solid, and rear is transparent\")"],"description":"Aimpoint's Micro T-2 as an AR-15 takes it: the sight on the LRP (Lever Release Picatinny) mount with the 39 mm spacer, its axis 39 mm over the rail. The mount goes on the rail and the sight on its deck, by the Micro footprint."},"bcm-mk2-lower-no-stock":{"id":"bcm-mk2-lower-no-stock","label":"Complete lower","name":"MK2 AR-15 Lower Receiver - Complete Lower - No Stock","manufacturer":"BCM","sku":"LRG-RMS-NO-STOCK","url":"https://www.primaryarms.com/bcm-mk2-ar-15-complete-lower-receiver-no-stock","platform":"ar15","alsoOn":[],"contains":{"lower_receiver":{"part":"bcm-mk2-lower-receiver","stated":"MK2 AR-15 Lower Receiver"},"trigger":{"part":"bcm-pnt-trigger","stated":"PNT (Polished Nickel Teflon) trigger"},"grip":{"part":"bcm-grip-mod-4","stated":"BCM ergonomic pistol grip","note":"The Mod 4 by its photos (its star-in-a-ring panel, its coarse front ribs and its open bottom, as BCM's own Mod 4 photo; the Mod 3 has a door and fine ribs) and by Primary Arms' page of the same lower's cosmetic second, \"BCM Mod 4 pistol grip\"."},"receiver_extension":{"part":"bcm-mk2-receiver-extension","stated":"MK2 receiver extension carbine buffer tube"},"buffer":{"part":"bcm-mk2-buffer-t0","stated":"with T0 buffer (3.8 oz)"},"buffer_spring":{"part":"bcm-rifle-m16-action-spring","stated":"MK2 receiver extension carbine buffer tube with T0 buffer","note":"Not named on the page: BCM's MK2 tube \"require[s] a M16 rifle action spring\", and BCM's own MK2 kits name the \"Mil-Spec M16A4 rifle action spring\"."},"end_plate":{"part":"bcm-qd-end-plate","stated":"MK2 receiver extension carbine buffer tube","note":"Not named on the page: an installed tube is held by a plate and a castle nut, and BCM's MK2 kit (BCM-MK2RMS-M1T0) names its \"M4 Receiver QD End Plate\". The blem page of BCM's no-stock, no-trigger lower names a \"QD sling mount end plate\" too."},"castle_nut":{"part":"bcm-castle-nut","stated":"MK2 receiver extension carbine buffer tube","note":"Not named on the page: BCM's MK2 kit names its \"Lock Nut (Castle) M4\"."}},"mounted":[],"also":[],"description":"BCM's MK2 lower, its parts kit and polymer guard installed, with BCM's Mod 4 grip, its PNT trigger and its MK2 recoil system (the MK2 tube, the 3.8 oz T0 buffer and the M16 rifle spring), and no stock: \"Ready for any compatible stock or pistol brace\". BCM: \"When correctly installed and tuned, the patented* BCM MK2 RMS reduces felt recoil without affecting reliability.\""},"bcm-mk2-rms-m1t0":{"id":"bcm-mk2-rms-m1t0","label":"Buffer system","name":"MK2 Recoil Mitigation System - Mod 1 - T0","manufacturer":"BCM","sku":"BCM-MK2RMS-M1T0","url":"https://bravocompanyusa.com/bcm-mk2-recoil-mitigation-system-mod-1-t0/","platform":"ar15","alsoOn":[],"contains":{"receiver_extension":{"part":"bcm-mk2-receiver-extension","stated":"Mk2 Receiver Extension (approximately 3/4” longer than carbine), 7076T6, 8 position, Mil-Spec diameter"},"end_plate":{"part":"bcm-qd-end-plate","stated":"M4 Receiver QD End Plate (include mount for QD swivel)","note":"BCM's QD End Plate on file by its name; the kit's page gives no number for it."},"castle_nut":{"part":"bcm-castle-nut","stated":"Lock Nut (Castle) M4","note":"BCM's Receiver Extension Nut on file by its name; the kit's page gives no number for it."},"buffer":{"part":"bcm-mk2-buffer-t0","stated":"MK2 Mod 1 - T0 Buffer (weight = approximately 3.8oz)"},"buffer_spring":{"part":"bcm-rifle-m16-action-spring","stated":"Mil-Spec M16A4 rifle action spring"}},"mounted":[],"also":[],"description":"BCM's MK2 system whole: its eight-position receiver extension, about 3/4 in longer than a carbine tube, with the 3.8 oz MK2 T0 buffer, the M16 rifle action spring, a castle nut and a QD end plate. BCM: \"When correctly installed and tuned, the patented* BCM MK2 RMS reduces felt recoil without affecting reliability.\" Its buffer and tube go only with each other and that spring."},"bcm-stock-kit":{"id":"bcm-stock-kit","label":"Stock hardware kit","name":"Milspec Carbine Stock Hardware MOUNTING KIT (Mil-Spec)","manufacturer":"BCM","sku":"BCM-STOCK-HARDWARE-KIT","url":"https://bravocompanyusa.com/bcm-milspec-carbine-stock-hardware-mounting-kit-mil-spec/","platform":"ar15","alsoOn":[],"contains":{"receiver_extension":{"part":"bcm-receiver-extension","stated":"Receiver Extension - Mil-Spec, 6 position (machined from 7075T6)"},"end_plate":{"part":"bcm-end-plate","stated":"Receiver End Plate"},"castle_nut":{"part":"bcm-castle-nut","stated":"Lock Nut (Castle)"},"buffer":{"part":"bcm-carbine-buffer","stated":"Carbine Buffer Assembly (options for Std, H, H2, or H3)","note":"The standard one: the page sells the kit with any of BCM's four buffer weights, chosen there (\"Buffer Weight: Required: Carbine Buffer, H Carbine Buffer, H2 Carbine Buffer, H3 Carbine Buffer\"). A build with another weight in the buffer's slot has this kit's buffer set aside."},"buffer_spring":{"part":"bcm-carbine-action-spring","stated":"M4 Carbine Action Spring"}},"mounted":[],"also":[],"description":"What a carbine stock goes on, sold together: BCM's mil-spec six-position receiver extension, its end plate and castle nut, a carbine buffer and an action spring."},"bcm-urg-mid-16-mcmr-15":{"id":"bcm-urg-mid-16-mcmr-15","label":"Complete upper","name":"Standard 16\" Mid Length Complete Upper Receiver Group w/ MCMR-15 Handguard","manufacturer":"BCM","sku":"BCM-URG-MID-16-MCMR-15","url":"https://bravocompanyusa.com/bcm-standard-16-mid-length-upper-receiver-group-w-bcm-mcmr-15-handguard/","platform":"ar15","alsoOn":[],"contains":{"upper_receiver":{"part":"bcm-m4-upper","stated":"M4 Feed Ramp Barrel Extension and Upper Receiver; T-Marked Upper Receiver","note":"No number given. BCM's page shows the group with its forward assist and port door on (its photo 2); Primary Arms: \"M4 feed ramps and T-marked flat-top receiver\"."},"barrel":{"part":"bcm-16-mid-barrel","stated":"Barrel Length: 16in Barrel Style: Standard","note":"No number given: the standard (government) profile 16 in mid-length barrel, 1/7, chrome lined, as the page's description and Primary Arms' specifications (\"Barrel Contour Government\") have it."},"handguard":{"part":"bcm-mcmr-15-handguard","stated":"Handguard: MCMR-15"},"gas_block":{"part":"bcm-750-gas-block","stated":"They are fully assembled, headspaced, and test fired.","note":"Not named on any page: an assembled, test-fired upper under a free-float handguard has a low-profile block, and BCM's own is the catalog's. Which one is fitted isn't stated; under the handguard either way."},"gas_tube":{"part":"bcm-mid-gas-tube","stated":"They are fully assembled, headspaced, and test fired.","note":"Not named on any page: a mid-length upper has a mid-length tube, and BCM's own is the catalog's."},"muzzle":{"part":"a2-flash-hider","stated":"Muzzle Device: Required Free A2 Flash Hider (Installed)","note":"The choice the page starts with, of ten; its maker isn't named."}},"mounted":[],"also":["One 3\" Picatinny Rail Section","One BCM MCMR Sling Mount"],"description":"BCM's standard 16 in mid-length upper under its 15 in MCMR handguard, sold \"fully assembled, headspaced, and test fired\", with the free A2 flash hider installed. Its carrier and its charging handle are options that start at \"None\": the catalog's two BCM ones are what its page offers."},"daniel-defense-fixed-sight-set":{"id":"daniel-defense-fixed-sight-set","label":"Iron sight set","name":"Fixed Front & Rear Sight Combo (Rock & Lock®)","manufacturer":"Daniel Defense","sku":"19-088-09116","url":"https://www.primaryarms.com/daniel-defense-fixed-rear-iron-sight-combo","platform":"ar15","alsoOn":[],"contains":{},"mounted":[{"part":"daniel-defense-fixed-front-sight","stated":"1x Daniel Defense AR-15 Fixed Front Sight"},{"part":"daniel-defense-fixed-rear-sight","stated":"1x Daniel Defense AR-15 Fixed Rear Sight"}],"also":[],"description":"Daniel Defense's fixed front and A1.5 rear sights as one set (2.8 oz for both): one-piece 6061-T6 aluminium sights for a Picatinny rail, each held by one slotted screw into a self-locking insert, the front taking a standard A2 post and the rear the standard A2 dual aperture with an A1 windage wheel. Sold in black, Mil-Spec+ Brown and Tornado Grey."},"dead-air-rxd22ti-kit":{"id":"dead-air-rxd22ti-kit","label":"Silencer with its brake","name":"RXD22Ti with the XRF Xeno Rimfire Muzzle Brake","manufacturer":"Dead Air","sku":"RXD22TiBLK","url":"https://deadairsilencers.com/rxd22ti/","platform":"ar15","alsoOn":["taurus-tx22"],"home":"suppressor","contains":{"muzzle":{"part":"dead-air-xrf-brake","stated":"What's Included Xeno Rimfire Muzzle Brake | RXD674","note":"Dead Air's page of the RXD22Ti. The manual, p. 6: \"Thread the muzzle device onto your host firearm or into the suppressor until it bottoms out on the taper.\""},"suppressor":{"part":"dead-air-rxd22ti","stated":"Dead Air RXD22Ti Suppressor, .22 cal, Black","note":"Midwest Gun Works' name for the black item (RXD22TIBLK, one of the kit's offers); the Burnt Bronze item is RXD22TiBB."}},"mounted":[],"also":[],"description":"Dead Air's RXD22Ti rimfire silencer with the XRF brake it locks onto, as it is sold: the brake threads onto a 1/2-28 muzzle and the silencer onto the brake. Black (RXD22TiBLK) and Burnt Bronze (RXD22TiBB)."},"geissele-premium-mil-spec-buffer-tube-assembly-super-42-h1":{"id":"geissele-premium-mil-spec-buffer-tube-assembly-super-42-h1","label":"Buffer system","name":"Premium AR-15 H1 Buffer Tube Kit With Super 42 - Carbine","manufacturer":"Geissele Automatics","sku":"08-163B","url":"https://www.primaryarms.com/geissele-automatics-premium-mil-spec-buffer-tube-assembly-with-h1-buffer-and-super-42-spring_2","platform":"ar15","alsoOn":[],"contains":{"receiver_extension":{"part":"geissele-premium-mil-spec-buffer-tube","stated":"Mil-Spec diameter buffer tube"},"end_plate":{"part":"geissele-premium-mil-spec-buffer-tube-assembly-end-plate","stated":"end plate"},"castle_nut":{"part":"geissele-premium-mil-spec-buffer-tube-assembly-castle-nut","stated":"castle nut"},"buffer":{"part":"geissele-super-42-h1","stated":"Super 42 buffer spring H1 buffer","note":"The Super 42 set on file: its spring and the H1 buffer it is sold seated on, in the buffer's slot (it takes the spring's)."}},"mounted":[],"also":[],"description":"Geissele's six-position mil-spec carbine buffer tube with its castle nut and end plate, and its Super 42 braided spring on the H1 buffer, in one package. Primary Arms' features: Mil-Spec diameter buffer tube 7075-T6 aluminum, Type III hardcoat anodized Castle nut and end plate Triple-braided Super 42 buffer spring H1 buffer, optimized for carbine/mid-length gas systems 4 oz weight Black finish."},"geissele-premium-mil-spec-buffer-tube-assembly-super-42-h2":{"id":"geissele-premium-mil-spec-buffer-tube-assembly-super-42-h2","label":"Buffer system","name":"Premium AR-15 H2 Buffer Tube Kit With Super 42 - Carbine","manufacturer":"Geissele Automatics","sku":"08-163S-H2","url":"https://www.primaryarms.com/geissele-automatics-premium-mil-spec-buffer-tube-assembly-super-42-h2-ddc","platform":"ar15","alsoOn":[],"contains":{"receiver_extension":{"part":"geissele-premium-mil-spec-buffer-tube","stated":"Mil-Spec diameter buffer tube"},"end_plate":{"part":"geissele-premium-mil-spec-buffer-tube-assembly-end-plate","stated":"end plate"},"castle_nut":{"part":"geissele-premium-mil-spec-buffer-tube-assembly-castle-nut","stated":"castle nut"},"buffer":{"part":"geissele-super-42-h2","stated":"Super 42 buffer spring H2 buffer","note":"The Super 42 set on file: its spring and the H2 buffer it is sold seated on, in the buffer's slot (it takes the spring's)."}},"mounted":[],"also":[],"description":"Geissele's six-position mil-spec carbine buffer tube with its castle nut and end plate, and its Super 42 braided spring on the H2 buffer, in one package. Primary Arms' features: H2 buffer, best for carbine/mid-length gas systems (14.5\"-16\" barrel) Super 42 braided buffer spring, 15 percent stronger average return force than standard 7075-T6 aluminum, Type III hardcoat anodized Mil-Spec castle nut and end plate included 6 stock positi[ons]."},"geissele-premium-mil-spec-buffer-tube-assembly":{"id":"geissele-premium-mil-spec-buffer-tube-assembly","label":"Buffer tube assembly","name":"Premium Mil-Spec Buffer Tube Assembly","manufacturer":"Geissele Automatics","sku":"08-162B","url":"https://charliescustomclones.com/geissele-premium-mil-spec-buffer-tube-assembly-gray/","platform":"ar15","alsoOn":[],"contains":{"receiver_extension":{"part":"geissele-premium-mil-spec-buffer-tube","stated":"Premium Mil-Spec Buffer Tube","note":"Sold in black (08-162B), DDC (08-162S), ODG (08-162ODG) and gray (08-162G: the mpn in the markup of Charlie's page of the gray assembly, SKU G081637)."},"end_plate":{"part":"geissele-premium-mil-spec-buffer-tube-assembly-end-plate","stated":"end plate","note":"A mil-spec plate in every photo; named by no page. The same look in every colourway."},"castle_nut":{"part":"geissele-premium-mil-spec-buffer-tube-assembly-castle-nut","stated":"mil-spec castle nut","note":"A mil-spec nut in every photo; named by no page. The same look in every colourway."}},"mounted":[],"also":[],"description":"Geissele's six-position mil-spec carbine buffer tube (7075-T6, Type 3 hardcoat anodized in black, DDC, ODG or gray) with the mil-spec castle nut and end plate its package holds; no buffer or spring. \"Included in the package is a high-quality, mil-spec castle nut and end plate\" (its sellers). Whether Geissele still makes the gray, no page read says."},"geissele-super-duty-receiver-set":{"id":"geissele-super-duty-receiver-set","label":"Receiver set","name":"Super Duty Receiver Set","manufacturer":"Geissele Automatics","sku":"05-1171B","url":"https://www.primaryarms.com/geissele-automatics-super-duty-stripped-ar15-receiver-set-black","platform":"ar15","alsoOn":[],"contains":{"lower_receiver":{"part":"geissele-super-duty-stripped-lower","stated":"a Super Duty stripped lower receiver","note":"Charlie's Custom Clones' words for the set (05-1171S). Its Desert Dirt is drawn as the lower's own (fitted on Primary Arms' photos of the lower sold alone) and the upper's as the set's photographs at Aegis Cerakote have it: the two studios' DDC differ, and the set's own pair is one colour by Charlie's sentence."},"upper_receiver":{"part":"geissele-super-duty-stripped-upper","stated":"a Super Duty stripped upper receiver"}},"mounted":[],"also":[],"description":"Geissele's Super Duty stripped upper and stripped lower, sold as a matched pair in black or Desert Dirt Color. Charlie's Custom Clones: \"This matched set pairs a Super Duty stripped upper receiver with a Super Duty stripped lower receiver\"; \"Buying a matched set guarantees consistent color across both halves of your rifle\"."},"guntec-ar15-mil-spec-buffer-tube-set":{"id":"guntec-ar15-mil-spec-buffer-tube-set","label":"Buffer tube set","name":"AR-15 Mil-Spec Buffer Tube Set","manufacturer":"Guntec USA","sku":"MILTUBESET-CLEAR","url":"https://guntecusa.com/product/ar-15-mil-spec-buffer-tube-set-anodized-clear/","platform":"ar15","alsoOn":[],"contains":{"receiver_extension":{"part":"guntec-ar15-mil-spec-buffer-tube-gen-2","stated":"Six Position Buffer Tube","note":"Guntec's set pages don't call the tube Gen 2; the user's own set has the Gen 2's notch cut through its threads at the front end (2026-10-20). The set is sold in the tube's colours: royal purple, black chrome, gold plated and rainbow PVD sets are sold too, in colours the tube on file doesn't come in, and aren't offered here."},"end_plate":{"part":"guntec-ar15-end-plate","stated":"End Plate","note":"Black in every colourway's photographs on file, whatever the tube's colour."},"castle_nut":{"part":"guntec-ar15-heavy-duty-castle-nut","stated":"Castle Nut","note":"Guntec's heavy duty wide nut, by the user who owns a set: \"you can tell by the extra notches on the other side of the nut [the side that is smooth on the standard nut version]\" (2026-10-20). Black in every colourway."},"buffer":{"part":"guntec-ar15-carbine-buffer","stated":"3 oz CAR Buffer","note":"Guntec's Mil-Spec CAR Buffer (CARBUF: \"3.0 oz weight Aluminum Body, White Neoprene Head\"), by the user who owns a set (\"Gold, white bumper\", 2026-10-20) and by the set's own words. Guntec's set photographs since 2021 show its stainless buffer instead (CARBUF-SS, 3.2 oz, a black bumper), which is in the catalog as a part sold alone."},"buffer_spring":{"part":"guntec-ar15-chrome-silicon-buffer-spring","stated":"Upgraded Chrome Silicon Spring"}},"mounted":[],"also":[],"description":"What a carbine stock goes on, sold together in the tube's colour: Guntec's six-position mil-spec tube (the Gen 2), a nitrided steel end plate, its heavy duty wide castle nut, its 3 oz CAR buffer (an aluminium body with steel weights and a white bumper) and a chrome silicon action spring. 9.6 oz in all, by Guntec's page."},"holosun-aro-kit":{"id":"holosun-aro-kit","label":"Red dot on its mount","name":"ARO 2 MOA red dot, on its 1.63 in lower 1/3 co-witness pedestal mount","manufacturer":"Holosun","sku":"ARO-RD2","url":"https://www.holosun.com/products/aro-core-rd-2","platform":"ar15","alsoOn":[],"contains":{},"mounted":[{"part":"holosun-aro-163-mount","stated":"1.63\" Mount","note":"Holosun's page, \"Included Mounts\"; its manual: \"an all-new 1.63\" lower 1/3 co-witness pedestal mount\"."},{"part":"holosun-aro","stated":"ARO-CORE-RD-2","note":"Holosun's page, \"In The Box\". Drawn on the pedestal where Holosun's two side photos have it."}],"also":["the 1.05 in low mount (Holosun's page: \"Included Mounts 1.63\" Mount 1.05\" Mount\"): not on file, no photograph of it being on any page reached","a CR2032 battery, a lens cloth, a multi-tool and a wrench (Holosun's page, \"In The Box\")"],"description":"Holosun's ARO as it is sold: the sight on its 1.63 in pedestal, its axis 1.63 in over the rail (a lower 1/3 co-witness), with a 1.05 in low mount in the box too. The pedestal goes on the rail and the sight on its deck, by the Micro footprint."},"magpul-mlok-hand-stop-kit":{"id":"magpul-mlok-hand-stop-kit","label":"Hand stop kit","name":"M-LOK Hand Stop Kit","manufacturer":"Magpul","sku":"MAG608","url":"https://magpul.com/m-lok-handstop-kit.html","platform":"ar15","alsoOn":[],"contains":{},"mounted":[{"part":"magpul-mlok-index-panel","stated":"one M-LOK Index panel, which is reversible for a custom fit"},{"part":"magpul-mlok-rail-cover-type-2","stated":"one M-LOK Rail Cover Type 2","note":"\"The M-LOK Hand Stop Kit includes a Type 2 M-LOK Rail Cover, additional covers can be purchased for additional coverage\" (the instruction sheet)."},{"part":"magpul-mlok-hand-stop","stated":"Includes M-LOK Hand Stop"},{"part":"magpul-mlok-hand-stop-moe-adapter","stated":"Includes adapter for use with Magpul polymer M-LOK hand guards or aluminum hand guards with wider, flatter profiles","spare":true,"note":"The hand stop and the index panel bolt through it there, and its moulded middle takes the Type 2 cover's place (the instruction sheet, scenario 2). No hand guard in the catalog wants it."}],"also":["three T-nuts and six screws"],"description":"Magpul's M-LOK Hand Stop Kit: \"installs onto M-LOK hand guards to deliver a hand stop and finger index\". Sold in one colour to a kit: Black, FDE, ODG or Stealth Gray. On a machined metal or narrow M-LOK hand guard the hand stop and the index panel bolt straight into slots with T-nuts and the cover snaps into a slot of its own (Magpul's instruction sheet 072-0098-A, scenario 1). On a Magpul polymer hand guard, or an aluminium one with a wider, flatter profile, the two bolt through the adapter plate instead, and the cover isn't used (scenario 2)."},"panzer-ar57-ult-12":{"id":"panzer-ar57-ult-12","label":"Complete upper","name":"AR57 ULT Complete AR-15 Upper Receiver - 5.7x28mm - 12\"","manufacturer":"Panzer Arms","sku":"AR57ULT-12","url":"https://www.primaryarms.com/ar57-ult-complete-upper-assembly-5-7-x28mm-12in","platform":"ar15","alsoOn":[],"contains":{"upper_receiver":{"part":"panzer-ar57-ult-12-upper","stated":"AR57 ULT Complete AR-15 Upper Receiver - 5.7x28mm - 12\""},"buffer":{"part":"panzer-ar57-buffer","stated":"proprietary carbine buffer","note":"Classic Firearms' words for what comes with the 16 in (\"proprietary carbine buffer\"); Primary Arms: the monobloc integrates the \"buffer\". Not sold alone on any page found."},"magazine":{"part":"fn-p90-50-magazine","stated":"50-round magazine","note":"Which maker's magazine isn't said: FN's P90 pattern is what the upper takes (Small Arms Review: \"uses 50-shot P90 magazines\", \"standard FN P90 magazine\"), and FN's is the catalog's."}},"mounted":[],"also":[],"description":"Panzer Arms' AR57 ULT, a dedicated 5.7x28mm upper that feeds from FN's 50-round P90 magazine laid along its top and ejects down through the lower's empty magazine well, sold with the heavier buffer it needs and one magazine."},"panzer-ar57-ult-16":{"id":"panzer-ar57-ult-16","label":"Complete upper","name":"AR57 Ultra Light Tactical Complete AR-15 Upper Receiver - 5.7x28mm - 16\"","manufacturer":"Panzer Arms","sku":"ULT0116","url":"https://www.primaryarms.com/panzer-arms-ar57-ultra-light-tactical-5-7x28mm-complete-upper-16in","platform":"ar15","alsoOn":[],"contains":{"upper_receiver":{"part":"panzer-ar57-ult-16-upper","stated":"AR57 Ultra Light Tactical Complete AR-15 Upper Receiver - 5.7x28mm - 16\""},"buffer":{"part":"panzer-ar57-buffer","stated":"proprietary carbine buffer","note":"Classic Firearms' words for what comes with the 16 in (\"proprietary carbine buffer\"); Primary Arms: the monobloc integrates the \"buffer\". Not sold alone on any page found."},"magazine":{"part":"fn-p90-50-magazine","stated":"50-round magazine","note":"Which maker's magazine isn't said: FN's P90 pattern is what the upper takes (Small Arms Review: \"uses 50-shot P90 magazines\", \"standard FN P90 magazine\"), and FN's is the catalog's."}},"mounted":[],"also":[],"description":"Panzer Arms' AR57 ULT, a dedicated 5.7x28mm upper that feeds from FN's 50-round P90 magazine laid along its top and ejects down through the lower's empty magazine well, sold with the heavier buffer it needs and one magazine."},"primary-arms-slx-1-6x24-nova-deluxe-mount-kit":{"id":"primary-arms-slx-1-6x24-nova-deluxe-mount-kit","label":"Scope with a mount","name":"SLx 1-6x24mm SFP Rifle Scope Gen IV ACSS Nova Fiber Wire Reticle - Red Dot Bright™ with Primary Arms Deluxe 30mm Scope Mount","manufacturer":"Primary Arms","sku":"KIT-PA-SLX-1-6X24S-NOVA-PADLXSM","url":"https://www.primaryarms.com/KIT-PA-SLX-1-6X24S-NOVA-PADLXSM","platform":"ar15","alsoOn":[],"contains":{},"mounted":[{"part":"primary-arms-deluxe-30mm-mount","stated":"Primary Arms Deluxe AR-15 Scope Mount - 30mm (SKU: PADLXSM)","note":"The kit page lists its two components by name and number; this is the second."},{"part":"primary-arms-slx-1-6x24-gen-iv","stated":"Primary Arms SLx 1-6x24mm SFP Rifle Scope Gen IV - Illuminated ACSS Nova Fiber Wire Reticle - Red Dot Bright™ (SKU: PA-SLX-1-6X24S-NOVA)","note":"The kit page's first component: the black scope by its number. Drawn in the mount with its saddle midway between the rings."}],"also":[],"description":"Primary Arms' 1-6x low-power variable scope (second focal plane, the red ACSS Nova fibre-wire reticle) sold together with its Deluxe AR-15 scope mount, a one-piece cantilever mount for a 30 mm tube with the optical axis 1.5 in above the rail. The scope is the black one (PA-SLX-1-6X24S-NOVA). The mount goes on the rail and the scope in its rings, where it slides to set the eye relief."},"sb-tactical-sbpdw":{"id":"sb-tactical-sbpdw","label":"Brace with its own tube","name":"SBPDW®","manufacturer":"SB Tactical","sku":"PDW-01-SB","url":"https://www.sb-tactical.com/product/sbpdw/","platform":"ar15","alsoOn":[],"home":"stock","contains":{"receiver_extension":{"part":"sb-tactical-sbpdw-receiver-extension","stated":"Proprietary buffer tube included","note":"Primary Arms' words; the maker's sheet: \"Complete assembly, ready-to-install\", and its instructions: \"With the tube inserted into the housing, begin threading the tube into the receiver\", \"Tighten the tube via the integral castle nut\". The housing is drawn with the tube: it stays on the rifle when the brace is taken off it (\"Remove the brace from the SBPDW assembly by depressing the adjustment and takedown levers together and sliding the brace to the rear.\")."},"stock":{"part":"sb-tactical-sbpdw-brace","stated":"Comes with adjustable nylon strap for custom fit","note":"The maker's page, of the brace and its strap; its two guide rods are drawn with it."}},"mounted":[],"also":[],"description":"SB Tactical's three-position pistol brace, \"Designed in conjunction with Maxim Defense\", sold as one assembly with its own aluminium receiver extension, its castle nut made on the tube, and a housing at the receiver that its two guide rods run through. It takes the rifle's own carbine buffer and spring. Black only."},"sig-romeo-msr-gen-2-kit":{"id":"sig-romeo-msr-gen-2-kit","label":"Red dot on its mount","name":"ROMEO-MSR GEN II red dot sight, 2 MOA red dot, on its see-through riser","manufacturer":"SIG Sauer","sku":"SORMSR101","url":"https://www.primaryarms.com/sig-sauer-romeo-msr-gen-ii-2-moa-red-dot-sight","platform":"ar15","alsoOn":[],"contains":{},"mounted":[{"part":"sig-romeo-msr-riser-mount","stated":"See-Through Riser Mount","note":"Impact Guns' list of what the box holds; SIG's sheet names it among the sight's features."},{"part":"sig-romeo-msr-gen-2","stated":"Romeo MSR Gen II","note":"Impact Guns' list of what the box holds. Drawn on the riser where Primary Arms' side view has it."}],"also":["a CR2032 battery, a T10 multi-tool and a rubber lens cover (SIG's sheet: \"CR2032 Battery, T10 Multi-Tool & Rubber Lens Cover\")"],"description":"SIG's ROMEO-MSR GEN II as it is sold: the sight on its see-through riser, its axis 1.41 in over the rail (absolute co-witness). Black is SORMSR101; flat dark earth, the sight's housing, is SORMSR111. The riser goes on the rail and the sight on its top, by the Micro footprint."},"sig-romeo5-gen-ii-kit":{"id":"sig-romeo5-gen-ii-kit","label":"Red dot on its mount","name":"ROMEO5 GEN II 1x20mm Compact Illuminated Dot Sight, 2 MOA red dot, on its M1913 I-BEAM mount","manufacturer":"SIG Sauer","sku":"SOR5101","url":"https://www.primaryarms.com/sig-sauer-romeo-5-gen-ii-2-moa-red-dot-sight","platform":"ar15","alsoOn":[],"contains":{},"mounted":[{"part":"sig-romeo5-i-beam-mount","stated":"M1913 I-BEAM Mount","note":"The manual's list of the box's contents."},{"part":"sig-romeo5-gen-ii","stated":"ROMEO5 GEN II Illuminated Dot Sight","note":"The manual's list of the box's contents. Drawn on the top plate where SIG's drawings have it."}],"also":["the M1913 Low Mount, with some numbers (the manual: \"M1913 Low Mount (Select SKU’s)\"): not on file","a rubber bikini lens cover, a multi-tool, a T20 L-key, a CR2032 battery and a lens cleaning cloth (the manual's list)"],"description":"SIG's ROMEO5 GEN II as it is sold: the sight on its M1913 I-BEAM mount, its axis 1.41 in over the rail (absolute co-witness). Black is SOR5101; Flat Dark Earth, the sight's housing, is SOR5111. The mount goes on the rail and the sight on its top plate, by the Micro footprint."},"sig-tango-msr-1-6x24-kit":{"id":"sig-tango-msr-1-6x24-kit","label":"Scope in its mount","name":"TANGO-MSR 1-6x24 in its ALPHA-MSR mount","manufacturer":"SIG SAUER","sku":"SOT61000","url":"https://www.sigsauer.com/tango-msr-lpvo-1-6x24mm-sfp.html","platform":"ar15","alsoOn":[],"contains":{},"mounted":[{"part":"sig-alpha-msr-30mm","stated":"Includes ALPHA-MSR 1 piece aluminum cantilever mount.","note":"Which ALPHA-MSR is on the mount itself in SOT61000's photos: \"P/N: SOA20014 30mm X 1.535\"\" engraved on its left side."},{"part":"sig-tango-msr-1-6x24","stated":"TANGO-MSR LPVO 1-6x24mm SFP","note":"SIG's name for the product (its page, as the user read it). Drawn in the mount with its saddle midway between the rings; SIG's photos have it a tenth of an inch further forward."}],"also":["lay-flat flip-back lens covers"],"description":"SIG's 1-6x low-power variable scope (second focal plane, illuminated MSR BDC6 reticle) as it is sold: in the ALPHA-MSR, a one-piece cantilever mount for its 30 mm tube with the optical axis 1.535 in above the rail. Black is SOT61000; coyote, scope and mount both, is SOTM61200. The mount goes on the rail and the scope in its rings, where it slides to set the eye relief."},"taurus-tx22-toro":{"id":"taurus-tx22-toro","label":"Pistol","name":"TX22 Gen 2 T.O.R.O., 22 LR, 4.6 in, Hard Anodized Black","manufacturer":"Taurus","sku":"1-2TX22P141","url":"https://www.sportsmans.com/shooting-gear-gun-supplies/handguns/taurus-tx22-gen-2-toro-22-long-rifle-46in-hard-anodized-black-pistol-221-rounds/p/1883977","platform":"taurus-tx22","alsoOn":[],"contains":{"frame":{"part":"taurus-tx22-frame","stated":"Frame Size Fullsize"},"slide":{"part":"taurus-tx22-toro-slide","stated":"Taurus Optic Ready Option T.O.R.O."},"barrel":{"part":"taurus-tx22-barrel-46","stated":"Barrel Length 4.6in"},"muzzle":{"part":"taurus-tx22-thread-protector","stated":"Threaded Yes","note":"The protector on the muzzle in every seller's picture; the manual's part list (the discovery's reading, Taurus's PDF refusing the harvester) has '63 THREAD PROTECTOR'."},"magazine":{"part":"taurus-tx22-magazine-16","stated":"it includes both 22-round and 16-round magazines","note":"The 16-round (Taurus 358-0017-01) is the one in every seller's picture of the pistol: a thin flush pad, 0.27 in below the grip (the magazine's owner's reading, 2026-11-05). The 22-round (358-0034-00) comes in the box too and is a part of its own, priced alone: a kit holds one part a slot."}},"mounted":[],"also":[],"description":"Taurus's TX22 in its optics-ready T.O.R.O. form: the Gen 2 polymer frame with its rail, the aluminium slide cut for a Shield RMSc red dot under a cover plate, a 4.6 in barrel threaded 1/2-28 with its protector, and a 22-round and a 16-round magazine.","ffl":true},"vltor-a5-buffer-kit":{"id":"vltor-a5-buffer-kit","label":"Buffer system","name":"A5 Buffer Kit","manufacturer":"VLTOR","sku":"RE-A5 and SP-A5","url":"https://vltor.com/products/re-a5-and-sp-a5","platform":"ar15","alsoOn":[],"contains":{"receiver_extension":{"part":"vltor-a5-receiver-extension","stated":"(1) RE-A5 Receiver Extension"},"end_plate":{"part":"vltor-lockplate","stated":"(1) Vltor Lockplate","note":"VLTOR sells it alone as its \"Receiver Extension End Plate\" (V2-1069-M1, \"Mil-Spec Receiver Extension End Plate\"): the kit's \"Lockplate\" by VLTOR's own catalog of buffer-system parts, where it is the one end plate."},"castle_nut":{"part":"vltor-castle-nut","stated":"(1) Vltor Castle Nut","note":"VLTOR sells it alone as its \"Receiver Extension Lock Nut\" (V2-1069-M3, \"Mil-Spec Receiver Extension Lock Nut (Castle Nut)\")."},"buffer":{"part":"vltor-a5h2-buffer","stated":"(1) A5H2 Buffer"},"buffer_spring":{"part":"vltor-a5-buffer-spring","stated":"(1) A5 Buffer Spring","note":"Its own page names it \"A5 Action Spring\" (V2-1174-C102)."}},"mounted":[],"also":[],"description":"VLTOR's A5 system whole: its seven-position receiver extension, 3/4 in longer than a carbine tube, with the A5H2 buffer, the rifle-length A5 spring, and VLTOR's mil-spec end plate and castle nut. The A5's buffers and spring belong only in its own tube (\"You cannot blend components from the different buffer systems.\")."},"vltor-sp-a5":{"id":"vltor-sp-a5","label":"Buffer and spring","name":"A5 Spring and Buffer Kit","manufacturer":"VLTOR","sku":"SP-A5","url":"https://www.vltor.com/products/sp-a5","platform":"ar15","alsoOn":[],"home":"buffer","contains":{"end_plate":{"part":"vltor-lockplate","stated":"(1) Vltor Lockplate"},"castle_nut":{"part":"vltor-castle-nut","stated":"(1) Vltor Castle Nut"},"buffer":{"part":"vltor-a5h2-buffer","stated":"(1) A5H2 Buffer"},"buffer_spring":{"part":"vltor-a5-buffer-spring","stated":"(1) A5 Buffer Spring"}},"mounted":[],"also":[],"description":"VLTOR's A5H2 buffer and rifle-length A5 spring with its end plate and castle nut, for its A5 receiver extension (\"requires the use of an A5 receiver extension tube\")."}},"bufferGuides":{"geissele-super-42":{"maker":"Geissele","label":"Super 42 chart","url":"https://www.milehighshooting.com/geissele-super-42-braided-wire-buffer-spring-and-buffer-combo-h2/","read":"2026-10-12","publisher":"retailer","note":"The table Geissele's sellers carry with the Super 42 (Mile High Shooting's page; the same rows at MidwayUSA), taken as the maker's: no page read names its author, and geissele.com isn't read (D59). On file in the Super 42's seeds (tools/harvest/sources/geissele-super-42-h1.yaml): \"Barrel Length Gas System Suppressed? Buffer Weight ...\".","options":{"H1":"geissele-super-42-h1","H2":"geissele-super-42-h2","H3":"geissele-super-42-h3"},"rows":[{"barrel":[18,null],"gas":["mid","rifle"],"suppressed":false,"says":["H1"],"stated":"18\" and above Mid-Length / Rifle Length No H1"},{"barrel":[14.5,16.5],"gas":["carbine","mid"],"suppressed":false,"says":["H1","H2"],"stated":"Between 14.5 - 16\" Carbine / Mid-Length No H1 or H2","read":"Up to a barrel its maker calls 16 in (Faxon states its pencil barrel's 16.13 in as \"16″ nominal\"): taken as below 16.5."},{"barrel":[14.5,16.5],"gas":["carbine","mid"],"suppressed":true,"says":["H2"],"stated":"Between 14.5 - 16\" Carbine / Mid-Length Yes H2","read":"Taken as below 16.5, as the row above."},{"barrel":[10.5,12],"gas":["carbine"],"suppressed":false,"says":["H2","H3"],"stated":"Between 10.5\" - 11.5\" Carbine No H2 or H3","read":"Up to a barrel its maker calls 11.5 in: taken as below 12."},{"barrel":[10.5,12],"gas":["carbine"],"suppressed":true,"says":["H3"],"stated":"Between 10.5\" - 11.5\" Carbine Yes H3","read":"Taken as below 12, as the row above."},{"barrel":[null,10.5],"gas":["carbine"],"suppressed":false,"says":["H2","H3"],"stated":"10\" and Under Carbine No H2 or H3","read":"Taken as below 10.5, where the next row begins, so that a 10.3 in barrel has a row."}]},"kynshot":{"maker":"KynSHOT","label":"word on its buffers","url":"https://www.kynshot.com/products/our-products/kynshot-rb5000hp-high-performance-96/","read":"2026-10-18","publisher":"manufacturer","note":"KynSHOT publishes no table (its selection guide asks for a cartridge, a gas system, a barrel length, a tube's depth and a suppressor and answers by form, \"only a guide as there are many factors\"); these rows are its product pages' own sentences. Its lighter RB5000L, for .300 Blackout's subsonic loads and a bolt that won't lock back, isn't on file, and no row here asks for ammunition.","options":{"RB5000":"kynshot-rb5000","RB5000HP":"kynshot-rb5000hp"},"rows":[{"gas":["pistol","carbine","mid","rifle"],"suppressed":true,"says":["RB5000HP"],"stated":"When a suppressor is added to an AR-15, increased back pressure often results in harsher cycling. The RB5000HP builds on the performance of the RB5000 with enhanced damping to better manage this added pressure.","read":"A gas-operated AR-15 only: \"DO NOT USE IN DIRECT BLOWBACK PCC's\" (both pages)."},{"gas":["pistol","carbine","mid","rifle"],"suppressed":false,"says":["RB5000"],"stated":"While the standard RB5000 can handle these applications, the RB5000HP is specifically designed for setups that require additional damping due to over pressure.","read":"The RB5000 is the standard model, and the HP is for what needs more damping (a suppressor, an over-gassed rifle): with no suppressor, the RB5000. A gas-operated AR-15 only."}]},"armaspec":{"maker":"Armaspec","label":"SRS and SMB chart","url":"https://armaspec.com/srs-smb-chart-size","read":"2026-10-18","publisher":"manufacturer","note":"The page's question tree (caliber, barrel, gas system, suppressed, folding stock), every 5.56 branch; its answers name Armaspec's Stealth Recoil Spring (SRS) and Sound Mitigation Buffer (SMB), and for a folding stock its braided spring (ARM181-AR15): only the SRS is on file. Its .300 Blackout and 9mm branches ask for ammunition or a carrier's type, which no part on file says, and aren't here. The tree offers four barrels; a barrel is taken at the one its maker's length names.","options":{"SRS-C":"armaspec-stealth-recoil-spring-gen4-c","SRS-H":"armaspec-stealth-recoil-spring-gen4-h","SRS-H2":"armaspec-stealth-recoil-spring-gen4-h2","SRS-H3":"armaspec-stealth-recoil-spring-gen4-h3","SMB-C":null,"SMB-H":null,"braided buffer spring":null},"rows":[{"folder":true,"says":["braided buffer spring"],"stated":"Folding stock: Yes → \"Perfect. A braided buffer spring is what you need!\""},{"cartridge":["5.56 NATO",".223 Rem"],"barrel":[16,16.5],"gas":["carbine"],"suppressed":true,"folder":false,"says":["SRS-C"],"stated":".223/5.56, 16\", Carbine, Suppressed: Yes → \"A 3.3/SRS-C is what you need!\"","read":"16 in: a barrel its maker calls 16 in, below 16.5."},{"cartridge":["5.56 NATO",".223 Rem"],"barrel":[16,16.5],"gas":["carbine"],"suppressed":false,"folder":false,"says":["SMB-H"],"stated":".223/5.56, 16\", Carbine, Suppressed: No → 3.8/SMB-H","read":"Below 16.5, as above."},{"cartridge":["5.56 NATO",".223 Rem"],"barrel":[16,16.5],"gas":["mid"],"suppressed":true,"folder":false,"says":["SRS-C"],"stated":".223/5.56, 16\", Mid-Length, Suppressed: Yes → 3.3/SRS-C","read":"Below 16.5, as above."},{"cartridge":["5.56 NATO",".223 Rem"],"barrel":[16,16.5],"gas":["mid"],"suppressed":false,"folder":false,"says":["SMB-C"],"stated":".223/5.56, 16\", Mid-Length, Suppressed: No → SMB-C (by its link)","read":"Below 16.5, as above."},{"cartridge":["5.56 NATO",".223 Rem"],"barrel":[14.5,15],"gas":["carbine"],"suppressed":true,"folder":false,"says":["SRS-H","SRS-H2"],"stated":".223/5.56, 14.5\", Carbine, Suppressed: Yes → \"A 3.8/SRS-H or a 4.7/SRS-H2 is what you need!\"","read":"14.5 in: below 15."},{"cartridge":["5.56 NATO",".223 Rem"],"barrel":[14.5,15],"gas":["carbine"],"suppressed":false,"folder":false,"says":["SMB-H"],"stated":".223/5.56, 14.5\", Carbine, Suppressed: No → SMB-H","read":"Below 15, as above."},{"cartridge":["5.56 NATO",".223 Rem"],"barrel":[14.5,15],"gas":["mid"],"suppressed":true,"folder":false,"says":["SRS-C"],"stated":".223/5.56, 14.5\", Mid-Length, Suppressed: Yes → 3.3/SRS-C","read":"Below 15, as above."},{"cartridge":["5.56 NATO",".223 Rem"],"barrel":[14.5,15],"gas":["mid"],"suppressed":false,"folder":false,"says":["SMB-H"],"stated":".223/5.56, 14.5\", Mid-Length, Suppressed: No → SMB (its link SMB-H)","read":"Below 15, as above."},{"cartridge":["5.56 NATO",".223 Rem"],"barrel":[11.5,12],"gas":["carbine"],"suppressed":true,"folder":false,"says":["SRS-H2"],"stated":".223/5.56, 11.5\", Carbine, Suppressed: Yes → \"A 4.7/SRS-H2 is what you need!\"","read":"11.5 in: below 12."},{"cartridge":["5.56 NATO",".223 Rem"],"barrel":[11.5,12],"gas":["carbine"],"suppressed":false,"folder":false,"says":["SMB-C"],"stated":".223/5.56, 11.5\", Carbine, Suppressed: No → SMB-C (by its link)","read":"Below 12, as above."},{"cartridge":["5.56 NATO",".223 Rem"],"barrel":[10.5,11],"gas":["carbine"],"suppressed":true,"folder":false,"says":["SRS-H2","SRS-H3"],"stated":".223/5.56, 10.5\", Carbine, Suppressed: Yes → \"A 4.7/SRS-H2 or a 5.6/SRS-H3 is what you need!\"","read":"10.5 in: below 11. (Unsuppressed, the page's message says 3.3/SRS-C and its link 3.8/SMB-H: it disagrees with itself, and no row is made of it.)"}]},"jp-enterprises":{"maker":"JP Enterprises","label":"SCS selection guide","url":"https://jprifles.com/1.4.7.2_os.php?menu_select=scs_guide","read":"2026-10-18","publisher":"manufacturer","note":"JP's selection guide (its page's script and its PDF's flow chart, p. 4): \"Is your rifle configured in one of the following ways? ■ Short-barreled rifle ■ Suppressed ■ Select fire ■ Piston operated ■ Using an H2 buffer\" NO → JPSCS2-15, YES → JPSCS2-15H2; a Law Tactical folder → its Law-specific models. And: \"Your manufacturer's recommendations take precedence over what we suggest here.\" The guide never answers the H3 (its own page: \"Only in extreme cases such as a severely over-gassed rifle without an adjustable gas block would the H3 be a functional recommendation over the H2\"), so a build with one is told the guide's answer. Select fire, piston operation and an H2 buffer aren't things a build on file says; the guide's .300 Blackout and larger branches ask for ammunition or a carrier's mass.","options":{"JPSCS2-15":"jp-silent-captured-spring-gen2","JPSCS2-15H2":"jp-silent-captured-spring-gen2-h2","JPSCS2-15H3":"jp-silent-captured-spring-gen2-h3","JPSCS2-15-LAW":null,"JPSCS2-15H2-LAW":null},"rows":[{"cartridge":["5.56 NATO",".223 Rem"],"gas":["pistol","carbine","mid","rifle"],"suppressed":true,"folder":["Law Tactical"],"says":["JPSCS2-15H2-LAW"],"stated":"Law folder: yes; configured as a short-barreled rifle, suppressed, select fire, piston operated or using an H2 buffer: yes → JPSCS2-15H2-LAW","read":"Law Tactical's adapters only (JP's: \"Are the Law Tactical Folder models of the JPSCS compatible with the Sylvan Arms folding stock adapter? No, these models are only compatible with the Law folder.\")."},{"cartridge":["5.56 NATO",".223 Rem"],"barrel":[null,16],"gas":["pistol","carbine","mid","rifle"],"folder":["Law Tactical"],"says":["JPSCS2-15H2-LAW"],"stated":"Law folder: yes; configured as a short-barreled rifle, suppressed, select fire, piston operated or using an H2 buffer: yes → JPSCS2-15H2-LAW","read":"A short-barreled rifle taken as a barrel under 16 in, braced or stocked: the guide asks what the rifle cycles like, not what the law calls it."},{"cartridge":["5.56 NATO",".223 Rem"],"gas":["pistol","carbine","mid","rifle"],"folder":["Law Tactical"],"says":["JPSCS2-15-LAW"],"stated":"Law folder: yes; configured as a short-barreled rifle, suppressed, select fire, piston operated or using an H2 buffer: no → JPSCS2-15-LAW","read":"Law Tactical's adapters only, as above. Any other folder is \"Law folder: no\", and the guide goes on as for a rifle without one."},{"cartridge":["5.56 NATO",".223 Rem"],"gas":["pistol","carbine","mid","rifle"],"suppressed":true,"says":["JPSCS2-15H2"],"stated":"Is your rifle configured in one of the following ways? ■ Short-barreled rifle ■ Suppressed ... YES → JPSCS2-15H2"},{"cartridge":["5.56 NATO",".223 Rem"],"barrel":[null,16],"gas":["pistol","carbine","mid","rifle"],"says":["JPSCS2-15H2"],"stated":"Is your rifle configured in one of the following ways? ■ Short-barreled rifle ... YES → JPSCS2-15H2","read":"A short-barreled rifle taken as a barrel under 16 in, braced or stocked, as above."},{"cartridge":["5.56 NATO",".223 Rem"],"gas":["pistol","carbine","mid","rifle"],"says":["JPSCS2-15"],"stated":"Is your rifle configured in one of the following ways? ... NO → JPSCS2-15","read":"None of the five that a build on file can say (select fire, a piston and an H2 buffer it can't)."}]},"vltor-a5":{"maker":"VLTOR","label":"A5 buffer table","url":"https://vltor.com/a5","read":"2026-10-28","publisher":"manufacturer","note":"VLTOR's \"Full Table\" on its A5 page (Configuration / Gas System / Barrel / Suppressed? / Recommended Buffer), for its A5 receiver extension alone: its buffers \"cannot be used in standard carbine receiver extensions\", so the chart is a build's only with the A5 tube (bufferGuide.ts `chartFor`, by the parts' `requires`). The page closes: \"When in doubt, start with the A5H2 and adjust from there.\" Two rows are left out: 'Competition / tuned low-gas Mid-length 14.5\"–16\" Yes (tuned) H0' and 'General purpose, lightly gassed Mid-length 16\" No H1' ask how the port is gassed, which no part on file states; the rifles they name are in the A5H2's row too, the one the page says to start from. Weights on the page: H0 3.8, H1 4.56, H2 5.3, H3 6.08, H4 6.83 oz; the A5H2 alone is on file.","options":{"A5H0":null,"A5H1":null,"A5H2":"vltor-a5h2-buffer","A5H3":null,"A5H4":null},"rows":[{"barrel":[14.5,16.5],"gas":["carbine","mid"],"says":["A5H2"],"stated":"Most versatile (start here) Carbine / Mid 14.5\"–16\" Either H2","read":"Up to a barrel its maker calls 16 in: taken as below 16.5, as the other charts read their 16 in rows."},{"barrel":[10.3,12],"gas":["carbine"],"suppressed":true,"says":["A5H3","A5H4"],"stated":"Suppressed SBR / heavy over-gas Carbine 10.3\"–11.5\" Yes H4","read":"Up to a barrel its maker calls 11.5 in: taken as below 12. Its rifles are in the H3's row too ('Over-gassed / suppressed Carbine 10.3\"–14.5\" Yes H3'); 'heavy over-gas', which tells the two apart, is the port's, which no part states: both are said."},{"barrel":[10.3,14.5],"gas":["carbine"],"suppressed":true,"says":["A5H3"],"stated":"Over-gassed / suppressed Carbine 10.3\"–14.5\" Yes H3","read":"Below 14.5, where the A5H2's row begins."}]}}},"issues":[{"level":"gap","where":"ledger aero-charging-handle.latch_reach","message":"Not published."},{"level":"gap","where":"ledger aero-enhanced-15-handguard.reach_inside","message":"Not sourced: it depends on the barrel and gas block under it, other parts. Its wall is 0.1 in by the two published figures (1.92 wide, 1.72 inside)."},{"level":"gap","where":"ledger aero-m4e1-lower.trigger_guard_front_y","message":"Onboarding checklist: As above. The M4E1's guard is integral (no ear holes), and the standard doesn't give this one: left missing; nothing is placed by it while the guard slot is occupied."},{"level":"gap","where":"ledger aero-r-one-10-3-handguard.reach_inside","message":"Not read: as on the 15 in, it depends on the barrel under it."},{"level":"gap","where":"ledger aero-r-one-12-7-handguard.reach_inside","message":"Not read: as on the 15 in, it depends on the barrel under it."},{"level":"gap","where":"ledger aero-r-one-15-handguard.reach_inside","message":"Not sourced: the barrel under it is another part, and its diameter under the handguard isn't on file (its traced photo shows it ahead of the handguard only)."},{"level":"gap","where":"ledger aero-r-one-16-6-handguard.reach_inside","message":"Not read: as on the 15 in, it depends on the barrel under it."},{"level":"gap","where":"ledger aero-r-one-7-3-handguard.reach_inside","message":"Not read: as on the 15 in, it depends on the barrel under it."},{"level":"gap","where":"ledger aero-r-one-9-3-handguard.reach_inside","message":"Not read: as on the 15 in, it depends on the barrel under it."},{"level":"gap","where":"ledger aero-s-one-15-handguard.reach_inside","message":"It depends on the barrel under it, another part: no figure."},{"level":"gap","where":"ledger aimpoint-duty-rds.eye_relief","message":"None to state: the sheet says \"Eye Relief: Unlimited\" and the manual \"Eye relief Unlimited\". A red dot: the part states no eye point."},{"level":"gap","where":"ledger aimpoint-micro-t-2.eye_relief","message":"None to state: the sheet says \"Eye Relief: Unlimited\" and the manual \"Unlimited\". A red dot: the part states no eye point."},{"level":"gap","where":"ledger aimpoint-pro.eye_relief","message":"None to state: the manual says \"Eye relief Unlimited\" and the 2011 sheet \"Eye relief Unlimited\". A red dot: the part states no eye point."},{"level":"gap","where":"ledger b5-bravo-stock.lop_collapsed","message":"B5 publishes none (its page, its installation sheet and six sellers' pages read 2026-10-05)."},{"level":"gap","where":"ledger b5-bravo-stock.lop_extended","message":"B5 publishes none."},{"level":"gap","where":"ledger b5-enhanced-sopmod-stock.lop_collapsed","message":"B5 publishes none (its page, its installation sheet and the sellers' pages read 2026-10-06)."},{"level":"gap","where":"ledger b5-enhanced-sopmod-stock.lop_extended","message":"B5 publishes none."},{"level":"gap","where":"ledger bcm-kag-mlok.reach_inside","message":"Not sourced: BCM gives no T-nut figure. The nuts stand 0.15 in above the face in BCM's side view as shipped, turned and loose; tightened they draw up under the slot's lips."},{"level":"gap","where":"ledger bcm-m4-upper.cover_latch_proud","message":"No view on file gives it a size: the housing's own drawing (8448784) wasn't read. Drawn at the beads' height until it is."},{"level":"gap","where":"ledger bcm-mcmr-10-handguard.reach_inside","message":"Not sourced: it depends on the barrel and gas block under it, other parts. Its wall is 0.1 in by BCM's two figures (1.5 wide, 1.3 inside)."},{"level":"gap","where":"ledger bcm-mcmr-13-handguard.reach_inside","message":"Not sourced: it depends on the barrel and gas block under it, other parts. Its wall is 0.1 in by BCM's two figures (1.5 wide, 1.3 inside)."},{"level":"gap","where":"ledger bcm-mcmr-15-handguard.reach_inside","message":"Not sourced: it depends on the barrel and gas block under it, other parts. Its wall is 0.1 in by BCM's two figures (1.5 wide, 1.3 inside)."},{"level":"gap","where":"ledger bcm-mid-gas-tube.weight","message":"Not published: BCM's page states none (its product data has \"weight\":null), and no seller's page for it is on file."},{"level":"gap","where":"ledger bcm-pmcr-carbine.inside_diameter","message":"BCM gives none, and no photo looks into an end. The model's inside is its outside less the wall (wall), which no view gives either."},{"level":"gap","where":"ledger bcm-pmcr-carbine.reach_inside","message":"Depends on the barrel, the gas tube and the heat shield, and on the wall, which no view gives: no figure, so the check reads as unmade."},{"level":"gap","where":"ledger bcm-pmcr-mid.inside_diameter","message":"BCM gives none, and no photo looks into an end. The model's inside is its outside less the wall (wall), which no view gives either."},{"level":"gap","where":"ledger bcm-pmcr-mid.reach_inside","message":"Depends on the barrel, the gas tube and the heat shield, and on the wall, which no view gives: no figure, so the check reads as unmade."},{"level":"gap","where":"ledger bcm-pnt-trigger.weight","message":"Not sourced: BCM states none (its page, its marketing site, its brochure; its shop's own product data has \"weight\":null). What sellers print is the parcel's: MidwayUSA \"shippingWeight\":0.266159 (\"0.266 Pounds\", 4.26 oz, in its page's data), AR15Discounts \"Weight 4 oz\" beside \"Dimensions 5.25 × 2 × 2 in\" (a box), KYGUNCO \"Weight 2 lb\" (the figure its other BCM pages carry). None is the part's, so none is entered: the build's weight says it is unknown. A reviewer's scale reading of the assembly, or of a mil-spec trigger group, would close it."},{"level":"gap","where":"ledger bcm-vertical-grip-mod-3-mlok.reach_inside","message":"Not sourced: BCM publishes no T-nut drawing, and Magpul's M-LOK FAQ says the nut's drawings are restricted. Until one is found the check against the handguard's room reads as unmade."},{"level":"gap","where":"ledger cloud-defensive-rein.reach_inside","message":"Not sourced: no page or sheet gives the T-nuts' height, and the one photo of them shows them hanging loose under the mount."},{"level":"gap","where":"ledger eotech-exps3.tube_od","message":"A holographic sight has no tube: its window is a rectangle in a housing (window_width, window_height). Not applicable; kept as the checklist's entry."},{"level":"gap","where":"ledger eotech-exps3.eye_relief","message":"EOTECH's manual, p. 9: \"Eye Relief Unlimited\". It has no eye point of its own and the part states no `eye`."},{"level":"gap","where":"ledger eotech-g45.exit_pupil","message":"Not stated for the G45: EOTECH's page has the row, and in it the field of view again (\"Exit Pupil 4°\"). The G33's page states its own (7.6 mm). With one seller's \"Objective 25\" and the 5X it would be 5 mm; nothing is drawn from it."},{"level":"gap","where":"ledger expo-arms-mlok-15-handguard.reach_inside","message":"Not sourced: what runs under it is another part (a barrel, a gas block, a gas tube), so the room is the build's and not this part's."},{"level":"gap","where":"ledger expo-arms-stripped-upper.weight","message":"No page states one: Primary Arms' page for it (the brand owner's) has no weight row and none in its text, its T-marked sibling's page none, and no seller or reviewer on file gives a figure. Not estimated: a build with it says its total is unknown (D61)."},{"level":"gap","where":"ledger geissele-139-chf-barrel.collar_slot_depth","message":"No source: the photo looks straight down into it. Not drawn until a figure or a view from the muzzle is on file."},{"level":"gap","where":"ledger geissele-139-chf-barrel.dimple_depth","message":"Huckleberry: \".750\" gas block diameter with a precision-machined dimple for secure mounting\". Primary Arms' close photo of the journal's underside (308babea3e35) shows it, a drilled spot with a coned floor just ahead of the collar, from an angle: neither its size nor its depth is read. Not drawn."},{"level":"gap","where":"ledger geissele-145-chf-barrel.dimple_depth","message":"No source: the one close photo looks straight into it. Not drawn until a figure or a view with its edge on the silhouette is on file."},{"level":"gap","where":"ledger geissele-145-chf-barrel.collar_slot_w","message":"A buyer on Primary Arms' page: \"it also has an indexing notch on the top and a dimple to help locate a gas block\". On the far side in the side photo; a mark a few pixels across in the three-quarter view (7f3cd09611e9) and on Rooftop's rendering. Not read, and not drawn. (The 13.9 in barrel's own photo shows its slot from above.)"},{"level":"gap","where":"ledger geissele-16-chf-barrel.dimple_depth","message":"No source: the photos look into it. Not drawn until a figure or a view with its edge on the silhouette is on file."},{"level":"gap","where":"ledger geissele-16-chf-barrel.collar_slot_w","message":"Primary Arms' three-quarter photo (f8d6141d8f0c) shows a notch in the collar's top in line with the port, a few pixels across; the side photo has it on the far side. Not read, and not drawn."},{"level":"gap","where":"ledger geissele-mk16-105-handguard.reach_inside","message":"Not sourced: it depends on the barrel and gas block under it, other parts. Its walls are 0.165 in by the sellers' two figures (1.59 across, 1.26 inside), 0.09 under a trough."},{"level":"gap","where":"ledger geissele-mk16-135-handguard.reach_inside","message":"Not sourced: it depends on the barrel and gas block under it, other parts. Its side walls are 0.165 in by the sellers' two figures (1.59 across, 1.26 inside); the bottom's is 0.09 in the trough."},{"level":"gap","where":"ledger geissele-mk16-15-handguard.reach_inside","message":"Not sourced: it depends on the barrel and gas block under it, other parts. Its side walls are 0.165 in by the sellers' two figures (1.59 across, 1.26 inside)."},{"level":"gap","where":"ledger geissele-ssa-e.boss_length","message":"Not read: no picture on file is square to the trigger's top or front, and in the parts view the boss's end and its foot are not told apart. What centres a trigger between a pocket's walls (.690, std.ar15.fcg_pocket_width); the Army's own are .680 (drawing 8448592). The model draws the standard's span (std.ar15.trigger_boss_length) and says so."},{"level":"gap","where":"ledger geissele-ssa-e.hammer_boss_length","message":"Not read, for the same want of a view as the trigger's. They and the spring's coils on them go between a pocket's walls (.690). The model draws the standard trigger's span and says so."},{"level":"gap","where":"ledger hexmag-series-2-ar15-30.body_height","message":"Onboarding checklist: Side view; overall_height minus the feed-lip block when the block is shared across a product line. Not read: the patent's side elevation draws no line where a feed-lip block would end, and nothing here needs it."},{"level":"gap","where":"ledger hexmag-series-2-ar15-30.feed_lip_block_height","message":"Onboarding checklist. Not read (as body_height)."},{"level":"gap","where":"ledger hexmag-series-2-ar15-30.stated_length","message":"Onboarding checklist. Hexmag's page states no length apart from its three sizes (overall_height, stated_front_to_back, stated_width). Shiner's page says \"Length 8.6500\" with no unit and no reference: not taken."},{"level":"gap","where":"ledger magpul-mlok-aluminum-rail-section-3-slot.reach_inside","message":"Not published: Magpul's M-LOK tips sheet sets the nut's top level with the recoil lug's bottom edge and gives neither's size."},{"level":"gap","where":"ledger magpul-mlok-aluminum-rail-section-5-slot.reach_inside","message":"Not published: Magpul's M-LOK tips sheet sets the nut's top level with the recoil lug's bottom edge (\"with the highest edge of the T-Nut even with the bottom edge of the recoil lug\") and gives neither's size."},{"level":"gap","where":"ledger magpul-mlok-aluminum-rail-section-7-slot.reach_inside","message":"Not published: Magpul's M-LOK tips sheet sets the nut's top level with the recoil lug's bottom edge and gives neither's size."},{"level":"gap","where":"ledger magpul-mlok-aluminum-rail-section-9-slot.reach_inside","message":"Not published: Magpul's M-LOK tips sheet sets the nut's top level with the recoil lug's bottom edge and gives neither's size."},{"level":"gap","where":"ledger magpul-mlok-hand-stop-moe-adapter.reach_inside","message":"Not measured. Either side of each screw hole a crescent seat stands off the mounting side, fore and aft (Wing Tactical's photo of the FDE kit from its mounting sides; Magpul's drawings): they stand in the hand guard's slot, as a hand stop's own do. The screws and T-nuts are the carried accessories'."},{"level":"gap","where":"ledger magpul-mlok-hand-stop-moe-adapter.carried_reach_inside","message":"No figure from Magpul. Each place's recess is 0.07 in deep in a 0.10 in plate (recess_depth): what stands off an accessory's band into a slot goes into it, and its screws go on through the floor into the hand guard's own slot."},{"level":"gap","where":"ledger magpul-mlok-hand-stop-moe-adapter.cover_underside_drop","message":"Not measured. Under the cover the plate is a waffle of ribs (Wing Tactical's photo of its mounting side), and three sources have its rim standing below the end sections' underside: that photo (a step where an end section meets it), Magpul's drawing from the side (the lower outline bulges under the cover, about 0.03 in) and Magpul's low side view of the plate (references/magpul-mlok-hand-stop 09443d72a495: the cover's lower edge 15 to 20 px below the end sections', where the two photos from 42 and 46 degrees have its wing tips level with them: something inboard of the tips, hidden from above). None is through a fitted camera. On a flat face it would touch before the ends do."},{"level":"gap","where":"ledger magpul-mlok-hand-stop.reach_inside","message":"Not sourced (as for the MVG: Magpul publishes no T-nut figure)."},{"level":"gap","where":"ledger magpul-mlok-index-panel.reach_inside","message":"Not sourced (as for the hand stop and the MVG: Magpul publishes no T-nut figure). FIG. 3 draws the lug that stands in the slot 0.06 in above the band, in broken lines; the T-nut beyond it isn't drawn."},{"level":"gap","where":"ledger magpul-mlok-mvg.reach_inside","message":"Not sourced. Magpul publishes no T-nut dimensions (its M-LOK FAQ: drawings of the nut are restricted pending an ITAR review), and the installation sheet sets the nut by the surface's thickness, not by a figure. Until one is found, the check against the handguard's room (data/interfaces.yaml, mlok) can't be made, and the app says so."},{"level":"gap","where":"ledger magpul-mlok-polymer-rail-section-11-slot.reach_inside","message":"Not published: Magpul gives no figure for its cammed T-nuts or for the recoil lugs under the section."},{"level":"gap","where":"ledger magpul-mlok-polymer-rail-section-3-slot.reach_inside","message":"Not published: Magpul gives no figure for its cammed T-nuts or for the recoil lugs under the section."},{"level":"gap","where":"ledger magpul-mlok-polymer-rail-section-5-slot.reach_inside","message":"Not published: Magpul gives no figure for its cammed T-nuts or for the recoil lugs under the section."},{"level":"gap","where":"ledger magpul-mlok-polymer-rail-section-7-slot.reach_inside","message":"Not published: Magpul gives no figure for its cammed T-nuts or for the recoil lugs under the section."},{"level":"gap","where":"ledger magpul-mlok-polymer-rail-section-9-slot.reach_inside","message":"Not published: Magpul gives no figure for its cammed T-nuts or for the recoil lugs under the section."},{"level":"gap","where":"ledger magpul-mlok-qd-sling-mount.reach_inside","message":"Not sourced (as for the MVG and the hand stop: Magpul publishes no T-nut figure). The M-LOK tips sheet sets the nut by the surface's thickness ('the T-Nut \"gap\" must be slightly greater than the thickness of the mounting surface'), not by a figure."},{"level":"gap","where":"ledger magpul-moe-mlok-handguard-carbine.inside_diameter","message":"Magpul gives none. The model's inside is its outside less the wall (wall), which no view gives either."},{"level":"gap","where":"ledger magpul-moe-mlok-handguard-carbine.reach_inside","message":"Depends on the barrel, the gas tube and the heat shield under it, and on the wall, which no view gives: no figure, so the check reads as unmade."},{"level":"gap","where":"ledger magpul-moe-mlok-handguard-mid.inside_diameter","message":"Magpul gives none: the room inside it isn't published. The model's inside is its outside less the wall (wall), which no view gives either."},{"level":"gap","where":"ledger magpul-moe-mlok-handguard-mid.reach_inside","message":"Depends on the barrel, the gas tube and the heat shield under it, and on the wall, which no view gives: no figure, so the check reads as unmade."},{"level":"gap","where":"ledger magpul-moe-sl-handguard-carbine.inside_diameter","message":"Magpul gives none. The model's inside is its outside less the wall (wall), which no view gives either."},{"level":"gap","where":"ledger magpul-moe-sl-handguard-carbine.reach_inside","message":"Depends on the barrel, the gas tube and the heat shield, and on the wall, which no view gives: no figure, so the check reads as unmade."},{"level":"gap","where":"ledger magpul-moe-sl-handguard-mid.inside_diameter","message":"Magpul gives none. The model's inside is its outside less the wall (wall), which no view gives either."},{"level":"gap","where":"ledger magpul-moe-sl-handguard-mid.reach_inside","message":"Depends on the barrel, the gas tube and the heat shield, and on the wall, which no view gives: no figure, so the check reads as unmade."},{"level":"gap","where":"ledger magpul-pmag-20-gen-m3.body_height","message":"Onboarding checklist: Side view; overall_height minus the feed-lip block when the block is shared across a product line. Not read: the block is not a piece of its own on a PMAG (the body is one moulding to the lips)."},{"level":"gap","where":"ledger magpul-pmag-20-gen-m3.feed_lip_block_height","message":"Onboarding checklist. Not read: a PMAG's body is one moulding from the floorplate to the feed lips, with no block to split off."},{"level":"gap","where":"ledger magpul-pmag-30-gen-m3.body_height","message":"Onboarding checklist: Side view; overall_height minus the feed-lip block when the block is shared across a product line."},{"level":"gap","where":"ledger magpul-pmag-30-gen-m3.feed_lip_block_height","message":"Onboarding checklist."},{"level":"gap","where":"ledger magpul-pmag-30-gen-m3.hang_below_magwell","message":"Onboarding checklist: Derived: overall_height minus the insertion depth, which is fixed by the mag-catch interface. A check on the seat since M3 (the lower's magazine_seat places magazines)."},{"level":"gap","where":"ledger magpul-pmag-d-60.body_height","message":"Onboarding checklist: Side view; overall_height minus the feed-lip block when the block is shared across a product line."},{"level":"gap","where":"ledger magpul-pmag-d-60.feed_lip_block_height","message":"Onboarding checklist."},{"level":"gap","where":"ledger magpul-pmag-d-60.hang_below_magwell","message":"Onboarding checklist: Derived: overall_height minus the insertion depth, which is fixed by the mag-catch interface. Not entered: how far the drum stands under a lower depends on that lower's mouth; the part's test says it for the catalog's two (app/tests/magpul-pmag-d-60.test.ts)."},{"level":"gap","where":"ledger mas-defense-nero-12-62-handguard.reach_inside","message":"Depends on the barrel and the gas block under it, other parts: no figure."},{"level":"gap","where":"ledger mas-defense-nero-15-handguard.reach_inside","message":"Depends on the barrel and the gas block under it, other parts: no figure."},{"level":"gap","where":"ledger mas-defense-nero-9-87-handguard.reach_inside","message":"Depends on the barrel and the gas block under it, other parts: no figure."},{"level":"gap","where":"ledger mft-battlelink-minimalist-stock.lop_collapsed","message":"Mission First Tactical publishes none (its page, its 2013 release and eight sellers' pages read 2026-10-13)."},{"level":"gap","where":"ledger mft-battlelink-minimalist-stock.lop_extended","message":"Mission First Tactical publishes none."},{"level":"gap","where":"ledger midwest-combat-rail-15-handguard.reach_inside","message":"Not sourced: it depends on the barrel and gas block under it, other parts. Its walls are 0.1 in by the maker's two figures (1.5 outside, 1.3 inside)."},{"level":"gap","where":"ledger midwest-industries-drop-in-mlok-carbine.inside_diameter","message":"Not published, and no view on file looks into either end square on. Left missing: the model's inside is its wall (assumed) inside its section."},{"level":"gap","where":"ledger midwest-industries-drop-in-mlok-carbine.reach_inside","message":"Not published. It depends on the barrel under it, another part: left missing, and the check reads as unmade."},{"level":"gap","where":"ledger midwest-industries-drop-in-mlok-mid.inside_diameter","message":"Not published, and no view on file looks into either end square on. Left missing: the model's inside is its wall (assumed) inside its section."},{"level":"gap","where":"ledger midwest-industries-drop-in-mlok-mid.reach_inside","message":"Not published. It depends on the barrel under it, another part: left missing, and the check reads as unmade."},{"level":"gap","where":"ledger otter-creek-polonium-k.thread_length","message":"No page on file says what length of 1/2x28 barrel thread the mount takes or is made for, and no manual of Otter Creek's is hosted anywhere the harvester may read. The mount is threaded through (mount_plug_length says how long it is), so the catalog's barrels' threaded ends, half an inch to .63, are inside it as drawn."},{"level":"gap","where":"ledger otter-creek-polonium.thread_length","message":"No page on file says what length of 1/2x28 barrel thread the mount takes or is made for, and no manual of Otter Creek's is hosted anywhere the harvester may read. The mount is threaded through and the can is open behind it, so a barrel's threaded end of any length stands in air as drawn."},{"level":"gap","where":"ledger psa-stripped-upper.weight","message":"No page states one: Palmetto State Armory's page for it, saved by the user on 2026-10-12, has no weight row and none in its text (Manufacturer, Platform, Material, Finish), and no other source is on file (the maker's site refuses the reader, D59; no seller's page for it has been harvested). Not estimated: a build with it says its total is unknown (D61)."},{"level":"gap","where":"ledger reptilia-aus-30mm-mount.clamp_bolt_shank_d","message":"Not read. The view from below shows each bolt as a dark bar 37 px across (0.22 in) with a glint down its middle: wider than a rail's slot (0.206), so the bar is the groove the bolt lies in with its shadow, not the bolt. The shanks aren't drawn across the rail's place."},{"level":"gap","where":"ledger streamlight-protac-rail-mount-hl-x.reach_inside","message":"Not sourced: the instruction sheet gives the M-LOK mount's screws (10-24 x 3/8 in) and no T-nut figure."},{"level":"gap","where":"ledger surefire-m340c-mini-scout-light-pro.reach_inside","message":"Not sourced, for the M-MLOK-S on either light: the Magpul sheet the manual says is enclosed isn't on file."},{"level":"gap","where":"ledger surefire-m340c-mini-scout-light-pro.width","message":"Not published, and it changes as the mount is swivelled."},{"level":"gap","where":"ledger surefire-procomp-556.thread_length","message":"No source states it (no drawing, no manual on file): no thread_length on its interface."},{"level":"gap","where":"ledger surefire-scout-light-pro-dual-fuel.width","message":"Not published, and it changes as the mount is swivelled."},{"level":"gap","where":"ledger surefire-scout-light-pro-dual-fuel.reach_inside","message":"Not sourced: no page on file gives the M-MLOK-S's nuts a figure, and the Magpul sheet SureFire's box is said to enclose isn't on file."},{"level":"gap","where":"ledger vg6-gamma-556.thread_length","message":"No page on file states how deep its threaded bore is, or what barrel thread it is made for: missing, and not given to the interface."},{"level":"gap","where":"part aero-556-16-mid-barrel gap","message":"A model: the app turns its traced outline, so its bore, its gas port, its index pin and its thread's rings aren't drawn, and its steps are as square as a 1000 px photo's pixels (0.018 in) — need The two other barrels' script run on this outline (the port and the pin are both in the photo on file, facing the lens), or a larger side photo"},{"level":"gap","where":"part aero-556-16-mid-barrel gap","message":"Where the 16 in is measured from — need Aero's statement (taken from the barrel's breech end, as the catalog's two other 16 in barrels are; from the bolt's face it would be an eighth shorter overall)"},{"level":"gap","where":"part aero-556-16-mid-barrel gap","message":"The muzzle shoulder closer than 0.06 in: its own photo has 14.89 (a pixel of it is 0.018 in, and its scale is the published 16 in), Aero's photo of the complete upper 14.95 ± 0.08 — need A larger straight side photo, or Aero's drawing"},{"level":"gap","where":"part aero-556-bcg gap","message":"Aero's own two side photos against the model — need A comparison by silhouette, as BCM's photos were: nothing of Aero's was measured for it"},{"level":"gap","where":"part aero-750-gas-block gap","message":"The second set screw's place along the tab, and both screws' sockets — need A photo of the underside: the two side views show one screw's end 0.258 in behind the front face and nothing of the other, and the end view shows a screw's tip in the bore's floor without saying which"},{"level":"gap","where":"part aero-750-gas-block gap","message":"The rear face: the gas tube's hole as Aero drills it — need A photo of the rear face, or of the bore from behind: the hole's size and depth are the Army's front sight's"},{"level":"gap","where":"part aero-750-gas-block gap","message":"Its length to better than a hundredth — need Aero publishes none: 1.013 in is the two side views in the boss's rows, each a few degrees off square (the ring's rows read 1.03 to 1.04). A seller's figure, or a view from above"},{"level":"gap","where":"part aero-750-gas-block gap","message":"Its weight against its metal — need The model's volume in steel comes to about 1.5 oz against Aero's 1.6: inside the section's ± (a hundredth of an inch on the ring's wall is a tenth of an ounce), and not a second reading of anything"},{"level":"gap","where":"part aero-ar15-front-sight-post-kit gap","message":"Aero's own page and photos of the kit — need Aero's product page for APRH100526C (not found), or a seller's photos of the post from the side and from above"},{"level":"gap","where":"part aero-ar15-front-sight-post-kit gap","message":"The kit's weight — need A seller's figure for the kit itself: KYGUNCO's 1 lb is a parcel's; the figure is its steel"},{"level":"gap","where":"part aero-carbine-gas-tube gap","message":"Its outside diameter and its bore, as Aero makes them — need A figure from Aero or a seller, or a view of its end with something of known size in it: the diameter drawn is the Army's drawing's, the bore what Aero's weight leaves"},{"level":"gap","where":"part aero-carbine-gas-tube gap","message":"The grade of its stainless steel — need Aero's own word for it (its pages say \"Stainless Steel\" and no more)"},{"level":"gap","where":"part aero-carbine-gas-tube gap","message":"The roll pin it comes with — need Its length, from Aero or a seller: the pin goes in the .078 cross hole and isn't drawn"},{"level":"gap","where":"part aero-carbine-gas-tube gap","message":"A carbine tube's own drawing — need The Army's drawing of the M4's gas tube (the package on file has the rifle's, 8448567): where its bend lies, and its rounds"},{"level":"gap","where":"part aero-carbine-gas-tube gap","message":"The sections of the two grooves round the plug and of the relief behind the head — need A close photo of each end with a scale on the tube: the product photos have them at one to four pixels"},{"level":"gap","where":"part aero-charging-handle checklist","message":"charging_handle checklist: \"latch_reach\" still missing"},{"level":"gap","where":"part aero-charging-handle gap","message":"Its latch — need The Army's drawing of the latch (8448519; the package has its parts list only), read and checked on Aero's photo: the handle's own (8448518) is read for its shaft, its T's heights, its lugs, its shoulder's breaks and the arc in its top, and the latch's height is the reference model's"},{"level":"gap","where":"part aero-enhanced-15-handguard interface mlok.reach_inside","message":"needs aero-enhanced-15-handguard.reach_inside"},{"level":"gap","where":"part aero-enhanced-15-handguard interface mlok_bottom.reach_inside","message":"needs aero-enhanced-15-handguard.reach_inside"},{"level":"gap","where":"part aero-enhanced-15-handguard gap","message":"Whether a clamp that hangs low beside a rail clears the tube's top (0.235 in under the rail's top as read; Aimpoint's LRP and EOTECH's STS mount hang 0.37 to 0.39 in as drawn, and stand in it; Magpul's MBUS 3 sights' hooks by a few thousandths of a cubic inch: app/tests/rail-clamps.test.ts) — need A photo of such a mount on this handguard's rail, or a sentence of Aero's on what its rail takes"},{"level":"gap","where":"part aero-enhanced-15-handguard gap","message":"The room inside its faces before the barrel (reach_inside: what an M-LOK accessory's nuts may take) — need The barrel's and the gas block's size under it, from the parts a build puts there"},{"level":"gap","where":"part aero-enhanced-15-handguard gap","message":"The M-LOK row along its underside (taken at the sides' stations with the sides' count, as a 12.63 in one's is: a grip under it may really bolt a slot off) — need A view of a 15 in's underside"},{"level":"gap","where":"part aero-enhanced-15-handguard gap","message":"Its section square on (each corner is read on a view in perspective, to 0.02 to 0.04 in), the rounds at its corners and the notch under its rail's rear end — need An end view taken from far off with a known size in frame, or a drawing; a view of its rear end from straight behind with no nut in it"},{"level":"gap","where":"part aero-enhanced-15-handguard gap","message":"How deep its barrel nut cut is, and what the BAR barrel nut's own sizes are (only its weight and the barrels it takes are published) — need The nut's length from a photo of it beside a rule, or Aero's drawing"},{"level":"gap","where":"part aero-enhanced-15-handguard gap","message":"How much room a clamp's jaws have under its rail's head: the tube's top stands 0.235 in below the rail's top beside the neck by two photos, and three clamps on file whose hooks reach 0.37 to 0.39 in below a rail's top (Aimpoint's Micro T-2 mount, EOTECH's G33 and G45 mounts) share space with the tube there as drawn — need Its section from a drawing, or a photo of one of those mounts on this rail"},{"level":"gap","where":"part aero-enhanced-15-handguard gap","message":"Which of its rail's lugs are cut through along a 15 in (carried on from a 12.63 in one's pattern), and the pocket in the third — need A view of a 15 in from straight above"},{"level":"gap","where":"part aero-enhanced-15-handguard gap","message":"The scallops milled along its flats' edges (their pitch and first station are read; their depth and outline aren't, and they aren't drawn) — need A close view of a flat's edge square on and one along it"},{"level":"gap","where":"part aero-enhanced-15-handguard gap","message":"Its weight with the nut, the eight screws and the shims on (Aero's two figures added: the screws and shims aren't weighed) — need A weight for the screw kit, or for the number APRA100218A as boxed less its carton"},{"level":"gap","where":"part aero-m4e1-enhanced-upper gap","message":"Its weight is worked out, not published (no page states the stripped receiver's: Aero's 6.9 oz for the Threaded receiver plus the platform's metal, 10 oz ± 1) — need A page of Aero's or a seller's for APAR600201C that states it"},{"level":"gap","where":"part aero-m4e1-enhanced-upper gap","message":"The platform square on: its flats, how far round its grooves run, the eight holes' angle and size, the thread in its front and where inside it the barrel seats — need A view of it from straight ahead and one from above with a known size in frame, or Aero's drawing"},{"level":"gap","where":"part aero-m4e1-enhanced-upper gap","message":"Its section below the bore's level (as the M4E1 Threaded receiver's gap) — need A view of it square from the front or the rear with a known size in frame"},{"level":"gap","where":"part aero-m4e1-enhanced-upper gap","message":"How far its left side's pad and cam pin boss stand out (each is drawn where the body as drawn is at the height of the edge it runs out on), the shape of the pad's ends and of the boss's flanks and undersides; and where along the receiver they are to better than 0.04 in (its own left view reads them that far behind the Threaded receiver's) — need A view from above, from below or from an end that shows the left wall in profile at a size to read; a left view of the stripped receiver in a colour that shows relief (its FDE one), square on, with the lens's place known from its own holes"},{"level":"gap","where":"part aero-m4e1-lower anchor trigger_guard.origin[1]","message":"needs aero-m4e1-lower.trigger_guard_front_y"},{"level":"gap","where":"part aero-m4e1-lower anchor trigger_guard.x[1]","message":"needs aero-m4e1-lower.trigger_guard_front_y"},{"level":"gap","where":"part aero-m4e1-lower checklist","message":"lower checklist: \"trigger_guard_front_y\" still missing"},{"level":"gap","where":"part aero-m4e1-lower gap","message":"the receiver's widths: the flared magwell and the integral trigger guard — need an end view or a maker's figure; the body at the pins is drawn at the TDP's width"},{"level":"gap","where":"part aero-m4e1-lower gap","message":"the stock's position in Aero's photo (it reads partly extended) — need a photo with the stock collapsed, or the exposed tube's position holes legible"},{"level":"gap","where":"part aero-m4e1-stripped-lower gap","message":"its weight: Aero's table says 8.35 with no unit, sellers 8.61 oz and 8.48 oz; and the model's metal is more than any of them — need a page or a reviewer that weighs a stripped M4E1 lower; and for the metal, the well's walls and the forging's inside: a view down into the receiver, square, or a section"},{"level":"gap","where":"part aero-m4e1-stripped-lower gap","message":"the integral guard: its width (0.59 ± 0.02) and its two slots' ends (± 0.04) are one reading each from the one view from below, which leans about 8 degrees along the receiver; its sides are drawn square and its slots cut straight up — need a square view from below of the whole receiver with both pin holes' ends in frame, or a view along it from the front at the guard's height"},{"level":"gap","where":"part aero-m4e1-stripped-lower gap","message":"the rear underside's facets and the tang's shape behind the lug (drawn as a half-round across) — need a view from behind and below, square to the tang"},{"level":"gap","where":"part aero-m4e1-stripped-lower gap","message":"the receiver extension's thread in the ring, and how far the pivot lug's slot runs down into the well's front wall — need a maker's figure or drawing; no page states either"},{"level":"gap","where":"part aero-m4e1-stripped-lower gap","message":"a sentence that states the hammer and trigger pins' size: Aero says 'compatible with all mil-spec AR15 parts' and sells its complete lower on this receiver with a 'Mil-spec Lower Parts Kit' — need a seller's sentence naming .154 pins"},{"level":"gap","where":"part aero-m4e1-threaded-upper gap","message":"Its section below the bore's level (drawn as the mil-spec forging's round body; Aero's left view of the FDE receiver has one even dark tone from the widest line down to a crease 0.41 in above the pin line, a flat face sloping in, where the round meets the lug walls at 0.50), and how far out its upper band stands (read from above as level with the rail's head, within a pixel) — need A view of it square from the front or the rear with a known size in frame"},{"level":"gap","where":"part aero-m4e1-threaded-upper gap","message":"Its forward assist housing's and its deflector's reach to better than a tenth of an inch (read on a small photo from above, taken from close) — need A view from above or from the rear at a larger size, or from further off"},{"level":"gap","where":"part aero-m4e1-threaded-upper gap","message":"How far its left side's pad and cam pin boss stand out (each is drawn where the body as drawn is at the height of the edge it runs out on), the shape of the pad's ends and of the boss's flanks and undersides; and the port's door seat and hinge bosses (not drawn) — need A view from above, from below or from an end that shows the left wall in profile at a size to read (the obliques on file have the part 250 px long); the hinge bosses outlined on Aero's right view with a depth from the same"},{"level":"gap","where":"part aero-mid-gas-tube gap","message":"Its outside diameter and its bore, as Aero makes them — need A figure from Aero or a seller, or a view of its end with something of known size in it: the diameter drawn is the Army's drawing's, the bore what Aero's weight leaves"},{"level":"gap","where":"part aero-mid-gas-tube gap","message":"A second photo of it — need Everything read on this tube is from one photograph (Aero's own, 70.7 px to the inch; its second file is the same photograph): a seller's picture of the mid-length tube, as the carbine tube has four, would check the bend's place and the two ends"},{"level":"gap","where":"part aero-mid-gas-tube gap","message":"The gas hole on this tube — need A view from below, or a side view sharp enough to show its notch: its place and size are the Army's drawing's, which the carbine tube's photos bear out for that tube"},{"level":"gap","where":"part aero-mid-gas-tube gap","message":"The roll pin it comes with — need Its length, from Aero or a seller: the pin goes in the .078 cross hole and isn't drawn"},{"level":"gap","where":"part aero-mid-gas-tube gap","message":"A mid-length tube's own drawing — need The package on file has the rifle's (8448567): where a mid-length tube's bend lies, and its rounds"},{"level":"gap","where":"part aero-mid-gas-tube gap","message":"The sections of the two grooves round the plug and of the relief behind the head — need A close photo of each end with a scale on the tube: the product photo has them at half a pixel to three"},{"level":"gap","where":"part aero-r-one-10-3-handguard interface mlok.reach_inside","message":"needs aero-r-one-10-3-handguard.reach_inside"},{"level":"gap","where":"part aero-r-one-10-3-handguard gap","message":"The room inside its side faces before the barrel (reach_inside: what an M-LOK accessory's nuts may take) — need The barrel's diameter under the handguard at the slots, from a photo of the bare barrel or Aero's profile figures"},{"level":"gap","where":"part aero-r-one-10-3-handguard gap","message":"Where its bottom row of M-LOK slots stands along it (stated at 6 o'clock, drawn where the sides' row is, not offered for mounting) — need A view of this R-ONE's underside, or the bottom row and a side row together in one photo"},{"level":"gap","where":"part aero-r-one-10-3-handguard gap","message":"Its inside away from the muzzle end: how thick its walls are and how far along the channel under its rail runs (from the side less shows through its upper outer row of slots than the section as drawn would let through) — need A view into it from the receiver's end with no barrel nut in it, or its section from a drawing"},{"level":"gap","where":"part aero-r-one-10-3-handguard gap","message":"Which of its rail's lugs are bridges along it, and what its rail has over the barrel nut (a shorter one has two round holes there) — need A view of it from straight above"},{"level":"gap","where":"part aero-r-one-10-3-handguard gap","message":"Whether a low-profile gas block clears it — need A rule from Aero's sentence (\"Compatible with low profile gas blocks\") once a gas block's height is on file"},{"level":"gap","where":"part aero-r-one-12-7-handguard interface mlok.reach_inside","message":"needs aero-r-one-12-7-handguard.reach_inside"},{"level":"gap","where":"part aero-r-one-12-7-handguard gap","message":"The room inside its side faces before the barrel (reach_inside: what an M-LOK accessory's nuts may take) — need The barrel's diameter under the handguard at the slots, from a photo of the bare barrel or Aero's profile figures"},{"level":"gap","where":"part aero-r-one-12-7-handguard gap","message":"Where its bottom row of M-LOK slots stands along it (stated at 6 o'clock, drawn where the sides' row is, not offered for mounting) — need A view of this R-ONE's underside, or the bottom row and a side row together in one photo"},{"level":"gap","where":"part aero-r-one-12-7-handguard gap","message":"Its inside away from the muzzle end: how thick its walls are and how far along the channel under its rail runs (from the side less shows through its upper outer row of slots than the section as drawn would let through) — need A view into it from the receiver's end with no barrel nut in it, or its section from a drawing"},{"level":"gap","where":"part aero-r-one-12-7-handguard gap","message":"Which of its rail's lugs are bridges along it, and what its rail has over the barrel nut (a shorter one has two round holes there) — need A view of it from straight above"},{"level":"gap","where":"part aero-r-one-12-7-handguard gap","message":"Whether a low-profile gas block clears it — need A rule from Aero's sentence (\"Compatible with low profile gas blocks\") once a gas block's height is on file"},{"level":"gap","where":"part aero-r-one-15-handguard interface mlok.reach_inside","message":"needs aero-r-one-15-handguard.reach_inside"},{"level":"gap","where":"part aero-r-one-15-handguard gap","message":"The room inside its side faces before the barrel (reach_inside: what an M-LOK accessory's nuts may take) — need The barrel's diameter under the handguard at the slots, from a photo of the bare barrel or Aero's profile figures"},{"level":"gap","where":"part aero-r-one-15-handguard gap","message":"Where its bottom row of M-LOK slots stands along it (stated at 6 o'clock, drawn where the sides' row is, not offered for mounting) — need A view of a 15 in R-ONE's underside, or the bottom row and a side row together in one photo"},{"level":"gap","where":"part aero-r-one-15-handguard gap","message":"Its inside away from the muzzle end: how thick its walls are and how far along the channel under its rail runs (from the side less shows through its upper outer row of slots than the section as drawn would let through) — need A view into it from the receiver's end with no barrel nut in it, or its section from a drawing"},{"level":"gap","where":"part aero-r-one-15-handguard gap","message":"Which of its rail's lugs are bridges along a 15 in, and what its rail has over the barrel nut (a shorter one has two round holes there) — need A view of a 15 in R-ONE from straight above"},{"level":"gap","where":"part aero-r-one-15-handguard gap","message":"Whether a low-profile gas block clears it — need A rule from Aero's sentence (\"Compatible with low profile gas blocks\") once a gas block's height is on file"},{"level":"gap","where":"part aero-r-one-16-6-handguard interface mlok.reach_inside","message":"needs aero-r-one-16-6-handguard.reach_inside"},{"level":"gap","where":"part aero-r-one-16-6-handguard gap","message":"The room inside its side faces before the barrel (reach_inside: what an M-LOK accessory's nuts may take) — need The barrel's diameter under the handguard at the slots, from a photo of the bare barrel or Aero's profile figures"},{"level":"gap","where":"part aero-r-one-16-6-handguard gap","message":"Where its bottom row of M-LOK slots stands along it (stated at 6 o'clock, drawn where the sides' row is, not offered for mounting) — need A view of this R-ONE's underside, or the bottom row and a side row together in one photo"},{"level":"gap","where":"part aero-r-one-16-6-handguard gap","message":"Its inside away from the muzzle end: how thick its walls are and how far along the channel under its rail runs (from the side less shows through its upper outer row of slots than the section as drawn would let through) — need A view into it from the receiver's end with no barrel nut in it, or its section from a drawing"},{"level":"gap","where":"part aero-r-one-16-6-handguard gap","message":"Which of its rail's lugs are bridges along it, and what its rail has over the barrel nut (a shorter one has two round holes there) — need A view of it from straight above"},{"level":"gap","where":"part aero-r-one-16-6-handguard gap","message":"Whether a low-profile gas block clears it — need A rule from Aero's sentence (\"Compatible with low profile gas blocks\") once a gas block's height is on file"},{"level":"gap","where":"part aero-r-one-7-3-handguard interface mlok.reach_inside","message":"needs aero-r-one-7-3-handguard.reach_inside"},{"level":"gap","where":"part aero-r-one-7-3-handguard gap","message":"The room inside its side faces before the barrel (reach_inside: what an M-LOK accessory's nuts may take) — need The barrel's diameter under the handguard at the slots, from a photo of the bare barrel or Aero's profile figures"},{"level":"gap","where":"part aero-r-one-7-3-handguard gap","message":"Where its bottom row of M-LOK slots stands along it (stated at 6 o'clock, drawn where the sides' row is, not offered for mounting) — need A view of this R-ONE's underside, or the bottom row and a side row together in one photo"},{"level":"gap","where":"part aero-r-one-7-3-handguard gap","message":"Its inside away from the muzzle end: how thick its walls are and how far along the channel under its rail runs (from the side less shows through its upper outer row of slots than the section as drawn would let through) — need A view into it from the receiver's end with no barrel nut in it, or its section from a drawing"},{"level":"gap","where":"part aero-r-one-7-3-handguard gap","message":"Which of its rail's lugs are bridges along it, and what its rail has over the barrel nut (a shorter one has two round holes there) — need A view of it from straight above"},{"level":"gap","where":"part aero-r-one-7-3-handguard gap","message":"Whether a low-profile gas block clears it — need A rule from Aero's sentence (\"Compatible with low profile gas blocks\") once a gas block's height is on file"},{"level":"gap","where":"part aero-r-one-9-3-handguard interface mlok.reach_inside","message":"needs aero-r-one-9-3-handguard.reach_inside"},{"level":"gap","where":"part aero-r-one-9-3-handguard gap","message":"The room inside its side faces before the barrel (reach_inside: what an M-LOK accessory's nuts may take) — need The barrel's diameter under the handguard at the slots, from a photo of the bare barrel or Aero's profile figures"},{"level":"gap","where":"part aero-r-one-9-3-handguard gap","message":"Where its bottom row of M-LOK slots stands along it (stated at 6 o'clock, drawn where the sides' row is, not offered for mounting) — need A view of this R-ONE's underside, or the bottom row and a side row together in one photo"},{"level":"gap","where":"part aero-r-one-9-3-handguard gap","message":"Its inside away from the muzzle end: how thick its walls are and how far along the channel under its rail runs (from the side less shows through its upper outer row of slots than the section as drawn would let through) — need A view into it from the receiver's end with no barrel nut in it, or its section from a drawing"},{"level":"gap","where":"part aero-r-one-9-3-handguard gap","message":"Which of its rail's lugs are bridges along it, and what its rail has over the barrel nut (a shorter one has two round holes there) — need A view of it from straight above"},{"level":"gap","where":"part aero-r-one-9-3-handguard gap","message":"Whether a low-profile gas block clears it — need A rule from Aero's sentence (\"Compatible with low profile gas blocks\") once a gas block's height is on file"},{"level":"gap","where":"part aero-s-one-15-handguard interface mlok.reach_inside","message":"needs aero-s-one-15-handguard.reach_inside"},{"level":"gap","where":"part aero-s-one-15-handguard gap","message":"The room inside its side faces before the barrel (reach_inside: what an M-LOK accessory's nuts may take) — need The barrel's diameter under the handguard at the slots, from a photo of the bare barrel or Aero's profile figures"},{"level":"gap","where":"part aero-s-one-15-handguard gap","message":"Where its bottom row of M-LOK slots stands along it, and how many (stated at 6 o'clock, seen from inside and at the clamp, drawn where the sides' row is, not offered for mounting) — need A view of a 15 in S-ONE's underside, or the bottom row and a side row together in one photo"},{"level":"gap","where":"part aero-s-one-15-handguard gap","message":"The corners of its section that only a view square on to an end shows (the side faces' width at their tops, the edge between the two lower faces, the bottom flat's width, a bridged lug's step, a window's length, a thin slot's width across its face): the R-ONE's figures by reference — need A view square on to an S-ONE's muzzle end, or its section from a drawing"},{"level":"gap","where":"part aero-s-one-15-handguard gap","message":"Its inside away from its two ends: the roof under the spine (drawn midway between the spine's top and a gas tube's), how far the arched channel under each rail block runs, and how thick its walls are (the model is 2% heavier as aluminium than its page says) — need A view into it from an end with no barrel nut in it, or its section from a drawing"},{"level":"gap","where":"part aero-s-one-15-handguard gap","message":"Its rail blocks' windows: how long each is and that it goes through to the channel under the block (deep and dark in the three-quarter views; the R-ONE's length by reference) — need A view of a 15 in S-ONE from straight above"},{"level":"gap","where":"part aero-s-one-15-handguard gap","message":"Its mounting hardware's weight: Aero's page says 1.9 oz, Wing Tactical's table 4.72 oz, a third seller 12.67 oz with it (7.95 with 4.72) — need A scale reading of the barrel nut, the taper lock nuts and the screw, or a page that says what each figure weighs"},{"level":"gap","where":"part aero-s-one-15-handguard gap","message":"Where it stops on a receiver (placed by Aero's rule for its length; no photo of it installed is on file) — need Aero's photo of the complete upper APAR700305M7 (an S-ONE on the M4E1 Threaded upper), which is on a host that refuses the reader"},{"level":"gap","where":"part aero-s-one-15-handguard gap","message":"Whether a low-profile gas block clears it — need A rule from Aero's sentence (\"Compatible with low profile gas blocks\") once a gas block's height is checked against its inside"},{"level":"gap","where":"part aimpoint-duty-rds-30mm-mount gap","message":"A seller on file for it, or for the sight on it (200758) — need A page at a seller on file with an offer for 200768 or 200758: The Shooting Centre (UK), Optics Trade (Slovenia) and a few European shops carry them"},{"level":"gap","where":"part aimpoint-duty-rds-30mm-mount gap","message":"Its own outline and its deck's height as read on its own photographs, which come 0.025 in under Aimpoint's figure less the sight's own axis over its base — need A straight view of the mount alone, or a drawing"},{"level":"gap","where":"part aimpoint-duty-rds-39mm-mount gap","message":"A page that sells the mount alone, with its own figures — need Aimpoint's 39 mm torsion nut mount under a number of its own, with a weight: the weight here is what the maker's figures for the pair and the sight leave"},{"level":"gap","where":"part aimpoint-duty-rds-39mm-mount gap","message":"The mount's own figures (its length, its height, where its recoil stop is) — need A drawing of the 39 mm one-piece mount, or Aimpoint's figure: the length is read off its left profile, the recoil stop's place isn't seen"},{"level":"gap","where":"part aimpoint-duty-rds gap","message":"A straight view from the front, the rear or above — need A studio end view or top view on a plain ground: the housing's width and section, how far the battery cap and the keypad stand out, the mount's width and its channel, where the elevation adjuster is along the top"},{"level":"gap","where":"part aimpoint-duty-rds gap","message":"What the 43 mm of sight height spans — need A page or a picture that shows the sight's underside off its mount: the profile reads 44.0 mm from the seam under its foot to its top at the scale of the 67 mm"},{"level":"gap","where":"part aimpoint-duty-rds gap","message":"Aimpoint's own pages (aimpoint.com, aimpoint.us) — need They refuse the project's reader and are left alone; a page the user saves from their own browser could be filed"},{"level":"gap","where":"part aimpoint-duty-rds gap","message":"A magnifier for it — need A maker's or a seller's sentence that a magnifier (Aimpoint's 3XMag-1 or 3X-C) goes behind the Duty RDS: none on file"},{"level":"gap","where":"part aimpoint-micro-lrp-39mm gap","message":"A page that sells the mount alone, with its own figures — need Aimpoint's LRP mount and 39 mm spacer under a number of their own, with a weight: the weight here is the pair's floor less the sight's"},{"level":"gap","where":"part aimpoint-micro-lrp-39mm gap","message":"The LRP mount's own height over the rail — need Aimpoint's figure for the LRP mount without a spacer, or a view of 200198 on a rail: the rail's top is placed by the 39 mm alone"},{"level":"gap","where":"part aimpoint-micro-lrp-39mm gap","message":"What the LRP's lever is made of and how it is finished — need A page that names it: its pale colour is matched to a seller's photograph of one (Aimpoint's own pictures have it lighter than a matte surface can be under the app's light), and it is drawn matte because it looks it"},{"level":"gap","where":"part aimpoint-micro-t-2 gap","message":"A straight view from the front, the rear or above — need A studio end view or top view on a plain ground: the housing's width and section, the turret housing's width, how far the switch and the windage cap stand out, the spacer's waist, the LRP base's width with its lever"},{"level":"gap","where":"part aimpoint-micro-t-2 gap","message":"Aimpoint's own pages (aimpoint.com, aimpoint.us) — need They refuse the project's reader and are left alone; a page the user saves from their own browser could be filed"},{"level":"gap","where":"part aimpoint-pro gap","message":"A straight view from the front, the rear or above — need A studio end view or top view on a plain ground: the main body's and the battery housing's section, how far the windage cap and the torque knob stand out, the ring's flats, the spacer's and the QRP2's widths. On file since the detail pass (2026-10-19), all oblique: Primary Arms' 12841_02 (e97955bbce77, from ahead and to the right, the QRP2's front end face against white), Optics Trade's sixteen photographs of the QRP2 alone (12195; 1000 px) and its photographs of the sight upside down (4015 px). A camera fitted to the first by the spacer's holes, the mount's ends and edges and the jaw's corner on the rail's flat fitted the mount to a quarter of a pixel and put the battery cap 160 px from where it is; with the battery cap or the front cover ring's rim it did not settle (the side profiles' heights, taken from a little above, carry a few hundredths each): its 0.57 to 0.63 in for the right face isn't a reading"},{"level":"gap","where":"part aimpoint-pro gap","message":"The mount's own sizes — need The spacer's and the ring base's widths, the QRP2's left side and how its jaws' lower outer edges are shaped (Primary Arms' photograph and Aimpoint's front quarter show a change of facet along the right jaw's outer face about level with the rail's top, not resolved) are on no page and in no square view: the spacer, the foot and the QRP2's left side are drawn 0.55 in each side of the rail's middle (assumed), the QRP2's right jaw 0.59 in by Aimpoint's two widths (qrp2_right_inboard), its foot 0.316 in under the rail's top by the right profile. So drawn, the QRP2's right jaw stands 0.044 cu in into the tube's top beside the neck of Aero's Enhanced rail (0.047 before the detail pass), as the T-2's and the Duty RDS's mounts do, and 0.0013 to 0.0015 into the shoulders under the head of Geissele's 15 and 13.5 in MK16 and Expo's rail (app/tests/rail-clamps.test.ts, LOW_SHELF): the right jaw's lower outer edge from a square end view would say whether it clears them"},{"level":"gap","where":"part aimpoint-pro gap","message":"Which of the maker's two generations of figures is the product sold now — need Aimpoint's own page for 12841 (it refuses the reader; a page the user saves from their own browser could be filed): 130 or 136 mm, 330 or 360 g, 192 or 220 g for the sight"},{"level":"gap","where":"part aimpoint-pro gap","message":"What the configuration's 81 mm of height spans — need A drawing or a sentence: no reading on the photos lands on it (71.9 mm from the mount's lowest edge to the top, 74.6 from the jaws, 83.1 from the knob's lowest edge on Primary Arms' photograph)"},{"level":"gap","where":"part aimpoint-pro gap","message":"Aimpoint's own pages (aimpoint.com, aimpoint.us) — need They refuse the project's reader and are left alone; a page the user saves from their own browser could be filed"},{"level":"gap","where":"part armaspec-stealth-recoil-spring-gen4-c gap","message":"The rod, the cap and the weight's bore — need A drawing, or an owner's measurements of the unit taken apart; the maker's design patent D864337 (marked on the bumper) is of an earlier generation's weight and gives no size"},{"level":"gap","where":"part armaspec-stealth-recoil-spring-gen4-c gap","message":"Where the unit stands in the rifle — need A figure for how far the carrier pushes the weight back on its rod with the bolt forward (the maker: 'Buffer mass is designed to stay under constant tension against the bolt carrier'), or a photo of it in a cut-away tube"},{"level":"gap","where":"part armaspec-stealth-recoil-spring-gen4-c gap","message":"What the steel as drawn lacks — need At stainless steel's density the model's steel is 4.95 oz of the maker's 6.2 oz, which would leave the bumper at 1.32 oz to the cubic inch, denser than a common polymer: something not seen in a photo (the rod's end inside the bumper, the weight's bore, a steel insert) holds 0.3 to 0.7 oz more. A photo or a description of the unit taken apart would close it"},{"level":"gap","where":"part armaspec-stealth-recoil-spring-gen4-h gap","message":"The rod, the cap and the weight's bore — need A drawing, or an owner's measurements of the unit taken apart; the maker's design patent D864337 (marked on the bumper) is of an earlier generation's weight and gives no size"},{"level":"gap","where":"part armaspec-stealth-recoil-spring-gen4-h gap","message":"Where the unit stands in the rifle — need A figure for how far the carrier pushes the weight back on its rod with the bolt forward (the maker: 'Buffer mass is designed to stay under constant tension against the bolt carrier'), or a photo of it in a cut-away tube"},{"level":"gap","where":"part armaspec-stealth-recoil-spring-gen4-h gap","message":"What the steel as drawn lacks — need At stainless steel's density the model's steel is 5.49 oz of the maker's 6.6 oz, which would leave the bumper at 1.17 oz to the cubic inch, denser than a common polymer: something not seen in a photo (the rod's end inside the bumper, the weight's bore, a steel insert) holds 0.3 to 0.7 oz more. A photo or a description of the unit taken apart would close it"},{"level":"gap","where":"part armaspec-stealth-recoil-spring-gen4-h2 gap","message":"The rod, the cap and the weight's bore — need A drawing, or an owner's measurements of the unit taken apart; the maker's design patent D864337 (marked on the bumper) is of an earlier generation's weight and gives no size"},{"level":"gap","where":"part armaspec-stealth-recoil-spring-gen4-h2 gap","message":"Where the unit stands in the rifle — need A figure for how far the carrier pushes the weight back on its rod with the bolt forward (the maker: 'Buffer mass is designed to stay under constant tension against the bolt carrier'), or a photo of it in a cut-away tube"},{"level":"gap","where":"part armaspec-stealth-recoil-spring-gen4-h2 gap","message":"What the steel as drawn lacks — need At stainless steel's density the model's steel is 6.24 oz of the maker's 7.4 oz, which would leave the bumper at 1.23 oz to the cubic inch, denser than a common polymer: something not seen in a photo (the rod's end inside the bumper, the weight's bore, a steel insert) holds 0.3 to 0.7 oz more. A photo or a description of the unit taken apart would close it"},{"level":"gap","where":"part armaspec-stealth-recoil-spring-gen4-h3 gap","message":"The rod, the cap and the weight's bore — need A drawing, or an owner's measurements of the unit taken apart; the maker's design patent D864337 (marked on the bumper) is of an earlier generation's weight and gives no size"},{"level":"gap","where":"part armaspec-stealth-recoil-spring-gen4-h3 gap","message":"Where the unit stands in the rifle — need A figure for how far the carrier pushes the weight back on its rod with the bolt forward (the maker: 'Buffer mass is designed to stay under constant tension against the bolt carrier'), or a photo of it in a cut-away tube"},{"level":"gap","where":"part armaspec-stealth-recoil-spring-gen4-h3 gap","message":"What the steel as drawn lacks — need At stainless steel's density the model's steel is 7.25 oz of the maker's 8.0 oz, which would leave the bumper at 1.48 oz to the cubic inch, denser than a common polymer: something not seen in a photo (the rod's end inside the bumper, the weight's bore, a steel insert) holds 0.3 to 0.7 oz more. A photo or a description of the unit taken apart would close it"},{"level":"gap","where":"part b5-bravo-stock gap","message":"Its seat on the tube from a photo (it is seated by its lock pin in the tube's front hole, ± 0.08 in) — need a straight side photo of it on a lower with both receiver pins in view, at any position"},{"level":"gap","where":"part b5-bravo-stock gap","message":"How light B5's colours are: its own pictures, which the five are matched on, are darker than the sellers' photos of the same stock (flat dark earth #786f62 on the lever's flat, against Primary Arms' and Wing Tactical's much paler tan; the blacks agree) — need a photo of a coloured stock beside a black one and a grey card, or on a rifle whose black parts set the exposure"},{"level":"gap","where":"part b5-bravo-stock gap","message":"What the steel hardware's black and its coloured coat are (B5 says only \"Color-Matched Steel Hardware\"), and whether the black pad is the cheek's black or a charcoal — need B5's or a seller's words for the finish; a photo of the black stock's pad beside its cheek in flat light"},{"level":"gap","where":"part b5-bravo-stock gap","message":"How deep the butt pad's checkering is; how far the QD boss's face and the rib's stand from the frame's face (drawn flush: the rib's reading through the camera agrees within ± 0.12 in; the boss's isn't read, its foot being hidden by the rib where the one fitted camera sees its wall); the web's thickness to better than ± 0.05 in (one photo, one camera: a second camera, fitted to T.REX ARMS' photo of the black stock from nearly the same corner, matched its outline less well and wasn't used) — need a photo square across the frame from behind or below with a known size in frame, or a second oblique from another corner with the camera fitted to it (B5's own photos are all straight side views)"},{"level":"gap","where":"part b5-bravo-stock gap","message":"How far back the bore runs and how its mouth is flared — need a photo into the stock's front, or the maker's drawing"},{"level":"gap","where":"part b5-bravo-stock gap","message":"A weight measured on a scale (B5 says 9.3 oz, its shop table 12, two sellers 9.6, two old reviews 8.25) — need a reviewer's weighing of the current stock, with the method"},{"level":"gap","where":"part b5-enhanced-sopmod-stock gap","message":"Its seat on the tube from a photo (it is seated by its lock pin in the tube's front hole, ± 0.08 in) — need a straight side photo of it on a lower with both receiver pins in view, at any position (the sellers' photos of it installed are oblique or 800 px wide)"},{"level":"gap","where":"part b5-enhanced-sopmod-stock gap","message":"How light B5's colours are: its own pictures, which the five are matched on, are darker than every seller's photo of the same stock (flat dark earth #786f62 on the lever's flat, against #a69d8e in Primary Arms' photo and #c1b197 in Wing Tactical's; the blacks agree) — need a photo of a coloured stock beside a black one and a grey card, or on a rifle whose black parts set the exposure"},{"level":"gap","where":"part b5-enhanced-sopmod-stock gap","message":"What the steel hardware's black and its coloured coat are (B5 says only \"Color Matched Steel Hardware\"), and whether the black pad is the housing's black or a charcoal — need B5's or a seller's words for the finish; a photo of the black stock's pad beside its housing in flat light"},{"level":"gap","where":"part b5-enhanced-sopmod-stock gap","message":"How deep the butt pad's diamond pattern is, and how far the frame's panels are recessed inside their ribs — need a view that shows their depth, or an oblique photo with the camera fitted to it"},{"level":"gap","where":"part b5-enhanced-sopmod-stock gap","message":"The storage tubes' own size, their caps' ribs and the walls' thickness away from the wings' tips — need the maker's drawing, or a photo square into the stock's front with a scale in its plane (T.REX ARMS' and Wing Tactical's are oblique)"},{"level":"gap","where":"part b5-enhanced-sopmod-stock gap","message":"The round hole on the top from above (its size is read from the side only, ± 0.04 in) — need a photo from straight above"},{"level":"gap","where":"part b5-enhanced-sopmod-stock gap","message":"A weight measured on a scale (B5 says 12.2 oz, its shop table 12, two sellers 11.8, which is its other SOPMOD's figure, one seller 14.4, a 2012 weighing 11.5) — need a reviewer's weighing of the current stock, with the method"},{"level":"gap","where":"part b5-type-23-p-grip gap","message":"The grip's section: how wide it is down its length, and how its straps round across — need a straight view of the grip from behind (square to the back strap), from the front and from below, from 8 ft or more; or a drawing or design patent of B5's for it (no patent marking page of B5's was looked for)"},{"level":"gap","where":"part b5-type-23-p-grip gap","message":"The lug slot's width, and the top's shape under the receiver — need a view of the grip's top from straight above with a scale, or the slot against the top's width in one"},{"level":"gap","where":"part b5-type-23-p-grip gap","message":"Its seat read on the grip installed (it is seated by its interface) — need a straight side photo of a Type 23 on a lower with the receiver's pins in view"},{"level":"gap","where":"part b5-type-23-p-grip gap","message":"The hollow under the base that B5's grip plug goes into — need a view of the base from below"},{"level":"gap","where":"part b5-type-23-p-grip gap","message":"Whether B5's 2.20 oz takes in the T30 screw — need B5's word, or a weighing of the grip with and without it"},{"level":"gap","where":"part bca-556-16-mid-barrel gap","message":"Which barrel ships today: with or without a cut-out ahead of the gas block's seat, with or without the dimple the photos show — need A dated photo of a delivered 1343-B556MM41617(P), or Bear Creek's own drawing of it"},{"level":"gap","where":"part bca-556-16-mid-barrel gap","message":"Its weight: four published figures from 28 to 30.4 oz, none with a method; 29 oz is adopted, which two listings give and the model's volume supports — need A weighed barrel, or Bear Creek saying whether its 1.75 lb is the barrel bare"},{"level":"gap","where":"part bca-556-16-mid-barrel gap","message":"A second view of its profile: it is one photo, yawed — need A straight side photo with a scale in the barrel's plane, or the maker's profile drawing"},{"level":"gap","where":"part bca-556-16-mid-barrel gap","message":"What its 16 in is measured between (taken from the breech face; the Army measures from the bolt's face, 0.126 further back) — need The maker's drawing, or a rod's reading on a barrel in hand"},{"level":"gap","where":"part bca-556-16-mid-barrel gap","message":"The gas port's diameter and the dimple's place — need The maker's figure: neither is published"},{"level":"gap","where":"part bca-556-16-mid-barrel gap","message":"Where its flange's rear face is within 0.03 in, and with it everything ahead of the receiver (the muzzle shoulder, the gas port) — need A straight side photo of the breech end. This one sees it from about 6° off square: the face is taken where the outline first stands over 0.53 in from the axis, 0.996 in ahead of the extension's rear face, as the standard extension has it (0.990); the flange's flat top begins 0.03 to 0.05 ahead of that, and if the face is there the shoulder is 14.88 in ahead of the receiver, not 14.91"},{"level":"gap","where":"part bca-stripped-lower gap","message":"its weight: the maker's page says 1 lb in a store's field, a seller 11.2 oz beside what reads as a box's size; neither is a weighing of the bare receiver — need a page or a reviewer that weighs the stripped receiver"},{"level":"gap","where":"part bca-stripped-lower gap","message":"a view square to the receiver: both photos are oblique (26 to 28 in away, 7 degrees above), so every reading goes through a fitted camera, and the left one's frame leans half a degree (its pivot hole's rim is unclear) — need a straight side photo with both pin holes open, or a photo from further away"},{"level":"gap","where":"part bca-stripped-lower gap","message":"everything read below the pin line on its photos is 0.02 to 0.03 in above the drawing's once its depth is allowed for (the grip's seat and lug, the trigger guard's holes), and the rear underside 0.03 to 0.06 above the reference model's: the drawing's and the model's are used, and the ears' and the well's lower edges may be drawn that much high — need a straight side photo, or where the camera's axis met the picture (it is taken at each picture's centre)"},{"level":"gap","where":"part bca-stripped-lower gap","message":"the depth of the two oblong pockets by the selector and of the panel on the well's right wall — need an oblique close-up with a known edge beside them, or a view along the receiver"},{"level":"gap","where":"part bcm-115-carbine-barrel gap","message":"The gas port's place, to better than a fortieth of an inch — need BCM's figure, or a photo with the port square to the lens and the collar's face in it (it is read here off two nicks a fraction of a pixel deep in the silhouette's edges; BCM's own gas block has its port 0.275 in ahead of its rear face, and this barrel's reads 0.26 ahead of the collar)"},{"level":"gap","where":"part bcm-115-carbine-barrel gap","message":"Where the 11.5 in is measured from — need BCM's statement (taken from the barrel's breech end, as the Army's drawing dimensions a barrel; from the bolt's face it would be an eighth shorter overall)"},{"level":"gap","where":"part bcm-115-carbine-barrel gap","message":"The dimple under the journal: its depth — need BCM's figure, or a photo of the journal's underside lit from the side (its width is on the silhouette, 0.144 in)"},{"level":"gap","where":"part bcm-115-carbine-barrel gap","message":"The gas port's diameter — need BCM's figure (.078 is read on an oblique close photo, ± .012; a mid-length chart has .075)"},{"level":"gap","where":"part bcm-115-carbine-barrel gap","message":"The extension's locking lugs and feed ramps, and the chamber's mouth — need The extension's drawing (8448550 isn't in the package): its inside is the reference CAD set's, turned; hidden once the barrel is in a receiver"},{"level":"gap","where":"part bcm-145-mid-barrel gap","message":"The scale along the barrel, to better than 1% — need A maker's drawing, or a side photo taken square from a distance with a scale in the barrel's plane: the published length, the thread's pitch and the two known diameters are 1.3 to 1.5% apart in this photo"},{"level":"gap","where":"part bcm-145-mid-barrel gap","message":"Where the 14.5 in is measured from — need BCM's statement (taken from the barrel's breech end, as the Army's drawing dimensions a barrel; from the bolt's face it would be an eighth shorter overall)"},{"level":"gap","where":"part bcm-145-mid-barrel gap","message":"The dimple under the journal and the relief groove at the collar's front face: their sizes and depths — need BCM's figures, or a side photo with the dimple on the silhouette (Primary Arms' close view of the journal shows both from above)"},{"level":"gap","where":"part bcm-145-mid-barrel gap","message":"The gas port's diameter — need BCM's figure (.075 is a third-party chart's)"},{"level":"gap","where":"part bcm-145-mid-barrel gap","message":"The indexing pin's height — need A side photo of this barrel with the pin on the silhouette (the 16 in barrel's reading stands in: the same USGI extension by BCM's words)"},{"level":"gap","where":"part bcm-145-mid-barrel gap","message":"The extension's locking lugs and feed ramps, and the chamber's mouth — need The extension's drawing (8448550 isn't in the package): its inside is the reference CAD set's, turned; hidden once the barrel is in a receiver"},{"level":"gap","where":"part bcm-16-mid-barrel gap","message":"The muzzle end's scale, and with it the thread's length — need The thread's own pitch reads 9.2 px in the photo where 28 to the inch would be 9.8 at the published length's scale: 6% short, unexplained. A maker's drawing, or a straight side photo of the muzzle with a scale in its plane"},{"level":"gap","where":"part bcm-16-mid-barrel gap","message":"Where the 16 in is measured from — need BCM's statement (taken from the barrel's breech end, as the Army's drawing dimensions a barrel; from the bolt's face it would be an eighth shorter overall)"},{"level":"gap","where":"part bcm-16-mid-barrel gap","message":"The dimple under the journal: its diameter and depth — need BCM's figure, or a side photo with the dimple on the silhouette (it dents the lower edge by half a pixel here)"},{"level":"gap","where":"part bcm-16-mid-barrel gap","message":"The gas port's diameter — need BCM's figure (.075 is a third-party chart's)"},{"level":"gap","where":"part bcm-16-mid-barrel gap","message":"The extension's locking lugs and feed ramps, and the chamber's mouth — need The extension's drawing (8448550 isn't in the package): its inside is the reference CAD set's, turned; hidden once the barrel is in a receiver"},{"level":"gap","where":"part bcm-625-gas-block gap","message":"A straight end view, for the section's widths — need A photo of the block end-on with its bore seen through (every one on file is a three-quarter view), or a maker's drawing: it would say whether the .625 block's ring is the .750's 0.88 in or the 0.85 its own photo reads"},{"level":"gap","where":"part bcm-625-gas-block gap","message":"Its weight — need BCM publishes none and no seller's page read states one (MidwayUSA's 0.183 lb is the parcel's; a second parts-database page said to carry 2.8 oz wasn't read): it is worked out from its steel, 1.93 oz ± 0.12. A scale would settle it"},{"level":"gap","where":"part bcm-625-gas-block gap","message":"Its height and length from its maker — need BCM's own figures: the 1.34 in is a parts database's for this number, unsourced, borne out by the block's own bore in its photo (1.33) and by the .750 block's two sellers"},{"level":"gap","where":"part bcm-625-gas-block gap","message":"The set screws' places along the tab and their holes, and the rear face — need A photo of the underside and one of the rear of this block (its oblique photo shows the front screw's hole in the bore's floor, its middle about 0.3 in behind the star face and about 0.2 across; the one rear view on its sellers' pages is BCM's picture of the .750 block)"},{"level":"gap","where":"part bcm-750-gas-block gap","message":"A straight end view, for the section's widths — need A photo of the block end-on with its bore seen through (BCM's own are three-quarter views), or a maker's drawing"},{"level":"gap","where":"part bcm-750-gas-block gap","message":"The block's length as the oblique photo shows it — need With the star face turned square, the block's long edges under a camera without perspective make it 0.89 in long against the side photo's 1.008 (the photo's perspective shortens them: the far face is about 5% smaller than the near one). By the mouth's fitted ellipse taken whole it read 1.3 to 1.45 in: the edge finder runs inside the rim along the ellipse's long axis, so that reading was dropped. A camera fitted to both oblique views (3ce1f7e276b9, ec4b889d2aba) with the mouth's rim picked by hand would close it; the side photo's length is the one used"},{"level":"gap","where":"part bcm-750-gas-block gap","message":"The set screws' places along the tab and their holes — need A photo of the underside (the two oblique photos show the front screw's hole in the bore's floor about a quarter of the length behind the star face)"},{"level":"gap","where":"part bcm-750-gas-block gap","message":"Its weight from its maker — need BCM publishes none; AR15Discounts' 2.08 oz is the only figure, and the model's volume in steel is about 1.4 oz (Aero's block of the same size weighs 1.6 by its maker): either the ring is thicker than the oblique photo shows or the seller's figure is a shipping weight"},{"level":"gap","where":"part bcm-bcg gap","message":"A weight of BCM's own — need BCM publishes none (its page's weight field is empty): the figure is the seller Primary Arms', beside a magazine's scale reading of a BCM group it doesn't name"},{"level":"gap","where":"part bcm-bcg gap","message":"The cartridge in BCM's words — need BCM's page names none; two sellers do, differently (5.56 NATO, 223 Remington)"},{"level":"gap","where":"part bcm-bcg gap","message":"Anything of BCM's own shape (its marking) — need A straight, scaled side photo, or BCM's drawing: the model is the Army's carrier"},{"level":"gap","where":"part bcm-carbine-action-spring gap","message":"Its weight — need BCM's figure or a scale: 1.95 oz is worked out from its wire's length and steel's density"},{"level":"gap","where":"part bcm-carbine-action-spring gap","message":"Its free length, wire and diameter as BCM makes it — need BCM's figures: they are the standard's and the Army's drawing's of the rifle's spring"},{"level":"gap","where":"part bcm-carbine-buffer gap","message":"Its own sizes — need BCM's figures or a photo with scale: its length, head and body are the standard pattern's"},{"level":"gap","where":"part bcm-delta-ring-assembly gap","message":"BCM's own figures — need Any size, weight or finish BCM states for these parts: every figure here is the Army's drawings' or the reference model's"},{"level":"gap","where":"part bcm-front-sight-base-f-750 gap","message":"Its weight — need BCM and Primary Arms publish none: the figure is its own steel by the model's volume (5.6 oz). A seller's or a reviewer's weight of the bare base"},{"level":"gap","where":"part bcm-front-sight-base-f-750 gap","message":"The F base's own height — need A drawing or a maker's figure for the F base's post seat: the .040 over the A2's is Windham Weaponry's (a rifle maker selling a taller post for the A2 base), and BCM says only \"taller\""},{"level":"gap","where":"part bcm-front-sight-base-f-750 gap","message":"Its widths — need An end-on or a top photo of BCM's base: every width across is the CAD set's .750 base, and BCM's forging differs from it in the side view (its wings 0.04 taller over the bore, its bayonet lug's foot 0.1 higher, its swivel hole 0.04 higher)"},{"level":"gap","where":"part bcm-front-sight-base-f-750 gap","message":"Where a gunsmith drills the front taper pin — need A drawing of the barrel and base assembly, or a photo of a pinned base from below"},{"level":"gap","where":"part bcm-gi-barrel-nut gap","message":"BCM's own figures — need Any size, weight or finish BCM states for this nut: every figure here is the mil-spec nut's"},{"level":"gap","where":"part bcm-gi-barrel-nut gap","message":"A square view of BCM's nut — need A side view of this nut, to read its length and the flange's against the mil-spec figures"},{"level":"gap","where":"part bcm-grip-mod-3 gap","message":"A size, a weight or an angle from BCM — need BCM publishes none: its sizes are one reviewer's calipers, each checked against a photo; a maker's drawing or spec sheet would settle them"},{"level":"gap","where":"part bcm-grip-mod-3 gap","message":"The section and the foot's width from a view square to them — need a straight rear, front or top view from further away (the only view from behind is a close photo), or a design patent's figures if BCM holds one for this grip"},{"level":"gap","where":"part bcm-grip-mod-3 gap","message":"Its seat, its lean and its drop read on the grip itself, installed (it is seated by its interface, and its size is one reviewer's calipers) — need a straight side photo of a Mod 3 on a lower with the receiver's pins in view (BCM's FDE photo of one, from the right and a little below, is on file and unread; Wing Tactical's pin-framed photo shows a Mod 0)"},{"level":"gap","where":"part bcm-grip-mod-3 gap","message":"Its lug slot's width from a view square to the top (it is read on the block's front face in two oblique photos, and comes to the lug's own width) — need a view of a Mod 3's top from above with a scale, or the slot against the top's width in one"},{"level":"gap","where":"part bcm-grip-mod-3 gap","message":"The tang against a lower with a trigger guard of its own — need the room behind an integral guard (the M4E1's) as a figure; T.REX ARMS says the tang has to be trimmed there"},{"level":"gap","where":"part bcm-grip-mod-4 gap","message":"A size, a weight or an angle from BCM — need BCM publishes none (its two shop pages, its marketing site's two pages, and Primary Arms', KYGUNCO's, Rainier Arms' and AT3 Tactical's pages were read): a maker's drawing, or a reviewer's calipers and scale, would settle them"},{"level":"gap","where":"part bcm-grip-mod-4 gap","message":"The open bottom's rim and how deep the hollow goes — need a view square to the base from below, with the foot's outline in it, and a section or a reviewer's description of the hollow"},{"level":"gap","where":"part bcm-grip-mod-4 gap","message":"The section from a view square to it — need a straight view from the base or the top from further away, or a design patent's figures if BCM holds one for this grip (no patent marking page of BCM's was found)"},{"level":"gap","where":"part bcm-grip-mod-4 gap","message":"Its weight — need a weighed figure (the model's polymer volume times a polyamide's density stands for it, without the screw and washer)"},{"level":"gap","where":"part bcm-h-buffer gap","message":"Its own sizes — need BCM's figures or a photo with scale: its length, head and body are the standard pattern's"},{"level":"gap","where":"part bcm-h2-buffer gap","message":"Its own sizes — need BCM's figures or a photo with scale: its length, head and body are the standard pattern's"},{"level":"gap","where":"part bcm-h3-buffer gap","message":"Its own sizes — need BCM's figures or a photo with scale: its length, head and body are the standard pattern's"},{"level":"gap","where":"part bcm-handguard-cap-round-750 gap","message":"Its weight — need BCM states no weight, material or finish: the weight is its steel worked out from the reference model's sizes. A seller's weight of BCM's cap itself"},{"level":"gap","where":"part bcm-handguard-cap-round-750 gap","message":"Its skirt and lip as BCM makes them — need BCM's one photo is of the face: the skirt, its lip and the tabs' depth are the reference model's. A photo of the cap from behind or edge-on"},{"level":"gap","where":"part bcm-handguard-cap-triangle-750 gap","message":"Its weight — need BCM states no weight, material or finish: the weight is its steel worked out from the drawing's sizes (Linemount's figure for its own triangular cap, 0.3 oz, agrees). A seller's weight of BCM's cap itself"},{"level":"gap","where":"part bcm-handguard-cap-triangle-750 gap","message":"Its skirt, its lip and its collar as BCM makes them — need No view of BCM's cap from the side or from behind: they are the Army's drawing's. A photo of the cap from behind or edge-on"},{"level":"gap","where":"part bcm-kag-mlok interface mlok.reach_inside","message":"needs bcm-kag-mlok.reach_inside"},{"level":"gap","where":"part bcm-kag-mlok gap","message":"Any size or weight from BCM or a seller — need BCM's page states none and its product data has \"weight\":null; a seller's table, a reviewer's calipers or scale, or a dimensioned drawing"},{"level":"gap","where":"part bcm-kag-mlok gap","message":"The width, from a view square to the part's end or its face — need an end-on or straight-down photo with a scale (a rail, a slot, a tape lying on it); the width is read on a face-on photo taken a little from one side"},{"level":"gap","where":"part bcm-kag-mlok gap","message":"How far the T-nuts reach inside the handguard (reach_inside) — need BCM's figure for its M-LOK nuts, or a side view of them tightened on a slot of known depth"},{"level":"gap","where":"part bcm-kag-mlok gap","message":"The face's hollow's depth, the cups' depth, how far up the toe's bore the screw is, and the toe's slots — need a view into each with a scale, or a section"},{"level":"gap","where":"part bcm-kag-mlok gap","message":"A design patent for the KAG — need The face's moulded PATENT marking names Magpul's M-LOK page (https://www.magpul.com/ip, BCM's FDE -4); a search lead, D745629, is tied to BCM or the KAG by no page on file"},{"level":"gap","where":"part bcm-m4-upper gap","message":"Its weight: two sellers' figures 1.4 oz apart, neither said to be the part's — need BCM's own figure, or a reviewer's on a scale"},{"level":"gap","where":"part bcm-m4-upper gap","message":"A view square to its rear or front end — need An end view with the rail in frame: its section is the reference model's of a mil-spec forging, checked on BCM's part only from above (the body's width, the rail's flat top)"},{"level":"gap","where":"part bcm-m4-upper gap","message":"How far the port cover's latch housing stands off the cover — need The Army's drawing of the housing (8448784), read"},{"level":"gap","where":"part bcm-m4-upper gap","message":"How far the raised band along the foot of the left wall and the tab on it stand out, and the body's section under the bore on BCM's own part — need A view along the receiver from its front or rear end, or from below, with the left wall's foot in profile: the band is drawn where the round body of the reference model is at its upper edge (0.074 out from the lug wall) and the tab by the lean of the band's rear end (0.059 more), both from one left view"},{"level":"gap","where":"part bcm-mcmr-10-handguard interface mlok.reach_inside","message":"needs bcm-mcmr-10-handguard.reach_inside"},{"level":"gap","where":"part bcm-mcmr-10-handguard interface mlok_between.reach_inside","message":"needs bcm-mcmr-10-handguard.reach_inside"},{"level":"gap","where":"part bcm-mcmr-10-handguard interface mlok_bottom.reach_inside","message":"needs bcm-mcmr-10-handguard.reach_inside"},{"level":"gap","where":"part bcm-mcmr-10-handguard gap","message":"A level side photo of this length alone (its muzzle end's two slopes are read on a photo from 18.5° above, each ± 0.03 to 0.06 in; the heights of the two slots across its rear end are the 15's) — need Primary Arms' gallery for BCM-MCMR-10-556-BLK (script-loaded: not fetched), whose first picture of the 15 is the level one; or any seller's straight side view"},{"level":"gap","where":"part bcm-mcmr-10-handguard gap","message":"The underside's M-LOK row seen square: how many slots it has and where it begins at the rear (the row is the family's reading at its front end, on BCM's photo of its KAG fitted under an MCMR, with the bottom face nearly edge-on; its count is the side faces', assumed) — need A photo of this length from below, its whole underside in frame; a seller's gallery or a review may have one"},{"level":"gap","where":"part bcm-mcmr-10-handguard gap","message":"The room inside its faces before the barrel (reach_inside: what an M-LOK accessory's nuts may take) — need The barrel's and the gas block's size under it, from the parts a build puts there"},{"level":"gap","where":"part bcm-mcmr-10-handguard gap","message":"Its section square on (the neck's width, the room between its walls and how high it goes under the rail, the corners' rounding, the rail's dovetail) — need An end view with a known size in frame (the views of its rear end on file are three-quarter ones); BCM's diagram of the MCMR's section is undimensioned"},{"level":"gap","where":"part bcm-mcmr-10-handguard gap","message":"Its two cross bolts' heads (each bolt is drawn as a plain pin as wide as its hole shows) — need a photo of an MCMR installed, from each side, close on the clamp"},{"level":"gap","where":"part bcm-mcmr-13-handguard interface mlok.reach_inside","message":"needs bcm-mcmr-13-handguard.reach_inside"},{"level":"gap","where":"part bcm-mcmr-13-handguard interface mlok_between.reach_inside","message":"needs bcm-mcmr-13-handguard.reach_inside"},{"level":"gap","where":"part bcm-mcmr-13-handguard interface mlok_bottom.reach_inside","message":"needs bcm-mcmr-13-handguard.reach_inside"},{"level":"gap","where":"part bcm-mcmr-13-handguard gap","message":"A level side photo of this length alone (its muzzle end's two slopes are read on a photo from 18.6° above, each ± 0.03 to 0.05 in; the heights of the two slots across its rear end are the 15's) — need Primary Arms' gallery for BCM-MCMR-13-556-BLK (script-loaded: not fetched), whose first picture of the 15 is the level one; or any seller's straight side view"},{"level":"gap","where":"part bcm-mcmr-13-handguard gap","message":"The underside's M-LOK row seen square: how many slots it has and where it begins at the rear (the row is the family's reading at its front end, on BCM's photo of its KAG fitted under an MCMR, with the bottom face nearly edge-on; its count is the side faces', assumed) — need A photo of this length from below, its whole underside in frame; a seller's gallery or a review may have one"},{"level":"gap","where":"part bcm-mcmr-13-handguard gap","message":"The room inside its faces before the barrel (reach_inside: what an M-LOK accessory's nuts may take) — need The barrel's and the gas block's size under it, from the parts a build puts there"},{"level":"gap","where":"part bcm-mcmr-13-handguard gap","message":"Its section square on (the neck's width, the room between its walls and how high it goes under the rail, the corners' rounding, the rail's dovetail) — need An end view with a known size in frame (the views of its rear end on file are three-quarter ones); BCM's diagram of the MCMR's section is undimensioned"},{"level":"gap","where":"part bcm-mcmr-13-handguard gap","message":"Its two cross bolts' heads (each bolt is drawn as a plain pin as wide as its hole shows) — need a photo of an MCMR installed, from each side, close on the clamp"},{"level":"gap","where":"part bcm-mcmr-15-handguard interface mlok.reach_inside","message":"needs bcm-mcmr-15-handguard.reach_inside"},{"level":"gap","where":"part bcm-mcmr-15-handguard interface mlok_between.reach_inside","message":"needs bcm-mcmr-15-handguard.reach_inside"},{"level":"gap","where":"part bcm-mcmr-15-handguard interface mlok_bottom.reach_inside","message":"needs bcm-mcmr-15-handguard.reach_inside"},{"level":"gap","where":"part bcm-mcmr-15-handguard gap","message":"The underside's M-LOK row seen square: how many slots it has and where it begins at the rear (the row is read at its front end only, on BCM's photo of its KAG fitted there, with the bottom face nearly edge-on; its count is the side faces', assumed) — need A photo of an MCMR from below, its whole underside in frame; a seller's gallery or a review may have one"},{"level":"gap","where":"part bcm-mcmr-15-handguard gap","message":"The room inside its faces before the barrel (reach_inside: what an M-LOK accessory's nuts may take) — need The barrel's and the gas block's size under it, from the parts a build puts there"},{"level":"gap","where":"part bcm-mcmr-15-handguard gap","message":"Its section square on (the neck's width, the corners' rounding, the rail's dovetail) — need An end view with a known size in frame; BCM's diagram of it is undimensioned"},{"level":"gap","where":"part bcm-mcmr-15-handguard gap","message":"Its two cross bolts' heads (each bolt is drawn as a plain pin as wide as its hole, its ends just inside the upper faces: BCM's photos of the handguard are of it off a rifle, the holes empty) — need a photo of an MCMR installed, from each side, close on the clamp"},{"level":"gap","where":"part bcm-mid-gas-tube gap","message":"Its weight — need A figure from BCM or from a seller's page for it (BCM's page states none): until then a build with it says its weight isn't known"},{"level":"gap","where":"part bcm-mid-gas-tube gap","message":"Where its bend lies along its length — need A straight side view of the mid-length tube with its bend in the picture's plane (BCM's photo has the bends turned from the camera); the Army's drawing dimensions the rifle's tube"},{"level":"gap","where":"part bcm-mk2-buffer-t0 gap","message":"Its sizes from BCM — need BCM's figures or a drawing to scale: its length is read on BCM's photo beside the MK2 tube; its head, collar, body and bumper are the standard's, which the photos bear out"},{"level":"gap","where":"part bcm-mk2-charging-handle gap","message":"Its weight — need BCM's own figure, or a reviewer's scale: BCM states none, and the one seller's 0.18 lb is twice what the modelled solid would weigh in aluminium (it may be a packed weight)."},{"level":"gap","where":"part bcm-mk2-charging-handle gap","message":"A straight side view — need A photo square to the handle's side (none is on file): the rear grip's profile, its lobes' crests, the latches' open rear edges and the shoulder block's and hook's heights."},{"level":"gap","where":"part bcm-mk2-charging-handle gap","message":"Its seat checked on a photo of it in a receiver — need A pin-framed photo of the handle latched in an upper: it is placed with its shoulder against the front wall of the receiver's notch (2026-10-05), as the Army's handle stops, which puts its latch's hook 0.02 to 0.045 in past the front end of the one latch slot traced (Expo Arms' left side) and its rear grip's two lobes in the square rear corners the app draws on a rail (the real rail's end is rounded)."},{"level":"gap","where":"part bcm-mk2-lower-receiver gap","message":"BCM's own figures for this receiver: no page gives a dimension or a weight (BCM sells no stripped lower and publishes nothing of the complete one; Primary Arms gives none) — need BCM's drawing or spec sheet, or a seller that weighs the stripped forging; until then the Army drawing's figures stand for its interfaces and its weight is worked out from its metal"},{"level":"gap","where":"part bcm-mk2-lower-receiver gap","message":"Where its weight sits: the worked-out weight is put at the middle of what is drawn, though most of the parts kit's steel is in the receiver's left face and its pins — need BCM's parts kit weighed piece by piece, or published weights for its pins and controls; they could then be lumps (mass.lumps)"},{"level":"gap","where":"part bcm-mk2-lower-receiver gap","message":"The roll's crest along the well's right top, the guard's width and its hidden ends: assumed (ledger entries marked so) — need a view along the receiver from ahead or behind (a seller's or reviewer's), and a view square to the guard from below"},{"level":"gap","where":"part bcm-mk2-lower-receiver gap","message":"Whether this forging is BCM's widebody or its standard lower — need a page that says (none of the three pages read does), or a view along the receiver from behind or ahead: none is on file, so it is drawn at the standard's widths"},{"level":"gap","where":"part bcm-mk2-receiver-extension gap","message":"Its weight — need BCM's figure or a scale: 4.2 oz is worked out from its sizes and 7075's density"},{"level":"gap","where":"part bcm-mk2-receiver-extension gap","message":"Its rear face — need A photo of the rear end, square on: its wall and any hole through it are a carbine tube's"},{"level":"gap","where":"part bcm-mk2-receiver-extension gap","message":"Its sizes from BCM — need A drawing or BCM's figures: every size here is read on its photos or is the mil-spec carbine tube's"},{"level":"gap","where":"part bcm-pmcr-carbine interface mlok.reach_inside","message":"needs bcm-pmcr-carbine.reach_inside"},{"level":"gap","where":"part bcm-pmcr-carbine interface mlok_bottom.reach_inside","message":"needs bcm-pmcr-carbine.reach_inside"},{"level":"gap","where":"part bcm-pmcr-carbine checklist","message":"handguard checklist: \"inside_diameter\" still missing"},{"level":"gap","where":"part bcm-pmcr-carbine gap","message":"Any size from BCM: its length, width, height and mounting length — need A drawing or a spec table from BCM, a seller's or a reviewer's own measurement"},{"level":"gap","where":"part bcm-pmcr-carbine gap","message":"Its front flange (its shape for the round cap, its length) and its inside (the wall, ribs, bosses) — need A photo into its front end, or of a half alone from inside"},{"level":"gap","where":"part bcm-pmcr-carbine gap","message":"Its section square on (the faces' angle, the spine's sides, the underside) — need An end view with a known size in frame"},{"level":"gap","where":"part bcm-pmcr-mid interface mlok.reach_inside","message":"needs bcm-pmcr-mid.reach_inside"},{"level":"gap","where":"part bcm-pmcr-mid interface mlok_bottom.reach_inside","message":"needs bcm-pmcr-mid.reach_inside"},{"level":"gap","where":"part bcm-pmcr-mid checklist","message":"handguard checklist: \"inside_diameter\" still missing"},{"level":"gap","where":"part bcm-pmcr-mid gap","message":"Any size from BCM: its length, width, height and mounting length — need A drawing or a spec table from BCM, a seller's or a reviewer's own measurement"},{"level":"gap","where":"part bcm-pmcr-mid gap","message":"Its front flange (its shape for the triangular cap, its length) and its inside (the wall, ribs, bosses) — need A photo into its front end, or of a half alone from inside"},{"level":"gap","where":"part bcm-pmcr-mid gap","message":"Its section square on (the faces' angle, the spine's sides, the underside) — need An end view with a known size in frame"},{"level":"gap","where":"part bcm-pmcr-mid gap","message":"BCM's insert adapters for a round cap (named by no number) — need BCM's page for the inserts, with their number and photos"},{"level":"gap","where":"part bcm-pnt-trigger checklist","message":"trigger checklist: \"weight\" still missing"},{"level":"gap","where":"part bcm-pnt-trigger gap","message":"The assembly's weight — need A weight of the part itself: BCM publishes none, and the sellers' figures are parcels' (4 oz, 0.266 lb) or a default (2 lb). A reviewer's scale reading would do"},{"level":"gap","where":"part bcm-pnt-trigger gap","message":"Where BCM's trigger rests in a lower — need A straight side photo of it installed, the receiver's pins in frame: the rest angle is the Aero lower's mil-spec trigger's"},{"level":"gap","where":"part bcm-pnt-trigger gap","message":"The hammer, the disconnector, the springs and the pins — need Their Army drawings are in the same scan (8448613, 8448635, 8448593, 8448611, 8448594, 8448609): a later pass, for the exploded view"},{"level":"gap","where":"part bcm-qd-end-plate gap","message":"Its sizes — need BCM's figures, or a photo of it with scale: every size here is read on photos scaled by the hole for the extension"},{"level":"gap","where":"part bcm-rifle-m16-action-spring gap","message":"Its weight — need BCM's figure or a scale: 2.2 oz is worked out from its wire's length and steel's density"},{"level":"gap","where":"part bcm-stock-mod-0 gap","message":"Its seat on the tube to better than 0.07 in (BCM's photo of it on a rifle is 33.7 px/in; the patent's section with a generic tube reads up to 0.26 in more) — need a close, straight side photo of it collapsed on a lower with both receiver pins in view"},{"level":"gap","where":"part bcm-stock-mod-0 gap","message":"Its length from its maker (a seller says 6.75 in; BCM's patent section and its photo of the stock on a rifle read 6.66 and 6.64) — need BCM's own figure, or a square side photo with a scale in the stock's plane"},{"level":"gap","where":"part bcm-stock-mod-0 gap","message":"A weight someone weighed (sellers say 8.2, 8.208 and 8.4 oz; the 2014 reviews 7.5; BCM none) — need a review that names its scale, or BCM's own figure"},{"level":"gap","where":"part bcm-stock-mod-0 gap","message":"The strut's own width (its ribbed underside is a narrow strip; it is drawn as wide as the butt, 1.46 in), the cheek's own section (drawn as the rear view's narrowed to the cheek's width read on its front face; its facets, the line along its side and the chamfer at its front aren't drawn), and whether body_width is the pad's: the patent's rear view is the pad's outline wherever the pad is the widest thing, and the Wolf Gray stock photographed from behind (9368820c28c7) has the pad's rim a little proud of the body all round and the rear body's face running on down from the wing to the QD panel as one surface, where the model's wing ends in a crease 1.65 in below the top. The cheek's width rests on one photo from ahead (65b0b1c49267, ± 0.03 in): a second one (a0647d7e661f, from ahead of its left side) doesn't show the face's near edge against the cheek's side, and gives no second reading — need a camera fitted to BCM's photo from the front right and below (b10b8afd338e: the bore's mouth is a circle of known size) for the strut and a second reading of the cheek, or a front, rear or underside photo square-on with a known size in frame"},{"level":"gap","where":"part bcm-stock-mod-0 gap","message":"How deep the two recessed panels are (assumed: 0.05 in round the QD socket, 0.1 in in the triangle, which the obliques show deeper), how their walls lean, and how high the pad's ribs stand at the middle of its face — need a camera fitted to BCM's photo of the butt from behind and below (525e4e3ca3a2), or a view square across the stock from below or behind with a known size in frame"},{"level":"gap","where":"part bcm-stock-mod-0 gap","message":"Which butt pad a Foliage Green stock sold today has (the one photograph on file, the distributor's earlier one, has the body's green; the Flat Dark Earth and the Wolf Gray stock were photographed later with a dark grey pad) — need a later photo of a Foliage Green Mod 0 stock"},{"level":"gap","where":"part bcm-vertical-grip-mod-3-mlok interface mlok.reach_inside","message":"needs bcm-vertical-grip-mod-3-mlok.reach_inside"},{"level":"gap","where":"part bcm-vertical-grip-mod-3-mlok gap","message":"Any size from BCM or a seller (length, height, width) — need A seller's table or a review's calipers; every size here is read on photos, the width through an oblique one"},{"level":"gap","where":"part bcm-vertical-grip-mod-3-mlok gap","message":"A straight view of the grip's end or base, for its width and section — need A square end view (the ridged face) or a view straight up at the base; a seller's gallery may have one"},{"level":"gap","where":"part bcm-vertical-grip-mod-3-mlok gap","message":"How far the T-nuts reach inside the handguard (reach_inside) — need A drawing of the M-LOK T-nut BCM uses, or a straight photo of a nut beside its 7 mm flats"},{"level":"gap","where":"part bcm-vertical-grip-mod-3-mlok gap","message":"Which way round BCM means by \"forward angle\" — need BCM's words or a straight side photo of it mounted, the muzzle in frame; the model is drawn as BCM's own installed photo (-6) has it, read by the side its marks are on"},{"level":"gap","where":"part blackdog-22lr-25 gap","message":"What shows through a smoke wall: the internal webs and the cartridge channel's walls — need Nothing more for their places (c8bd551fb5e2 has the smoke one beside the black): a pass on the model, as the 15's had"},{"level":"gap","where":"part blackdog-22lr-25 gap","message":"Its left side and its base: the catch notch and the base's slot are the 15's, and the base's isn't drawn — need A seller's or an owner's photo of a Sonic X 25 from the left and from under its base (the user doesn't own one)"},{"level":"gap","where":"part blackdog-22lr-25 gap","message":"The rear and middle grooves' widths and every groove's depth: the 15's — need A close photo of a 25's side wall, or its base's outline seen end on, where each groove shows as a notch"},{"level":"gap","where":"part cloud-defensive-rein interface mlok.reach_inside","message":"needs cloud-defensive-rein.reach_inside"},{"level":"gap","where":"part cloud-defensive-rein gap","message":"How far the mount's T-nuts reach inside the handguard (reach_inside) — need A figure from Cloud Defensive, or a photo of the mount tightened on a handguard seen from inside"},{"level":"gap","where":"part cloud-defensive-rein gap","message":"A second source for each colour (each rests on one studio's two pictures of one light) — need A seller's own photographs of the FDE, Earth Brown and OD Green lights under one light, or the maker's colour reference"},{"level":"gap","where":"part cloud-defensive-rein gap","message":"The weight without the battery, and the mount's own weight — need A maker's figure or a reviewer's scale"},{"level":"gap","where":"part cloud-defensive-rein gap","message":"The mounting feet's width across the body, and a straight end view of the light — need A photo of the body from an end, or the Scout mounting pattern's drawing"},{"level":"gap","where":"part cloud-defensive-rein gap","message":"Everything about the inline mount is read off two photos (± 0.02 to 0.04 in) — need The maker's drawing or figures for the mount (TOR-MLOKINLINE BLK): none is published"},{"level":"gap","where":"part cloud-defensive-rein gap","message":"The Picatinny mount the light shipped with at its 2022 launch (two sellers still list it) — need Nothing: the maker's page now lists the inline M-LOK mount, and that is what is modelled"},{"level":"gap","where":"part cmmg-lower-parts-kit gap","message":"CMMG's own figures: no page gives a dimension, a pin size or a trigger pull for this kit, and the maker states no weight — need CMMG's drawing or spec sheet, or the kit weighed out of its pack; until then the Army's drawings stand for its parts and Primary Arms' 7 oz for its weight"},{"level":"gap","where":"part cmmg-lower-parts-kit gap","message":"the selector lever's thickness (only its serrations are dimensioned on the Army's drawing) — need the plate's thickness: drawing 9381367's side view read at higher resolution, or a maker's figure"},{"level":"gap","where":"part cmmg-lower-parts-kit gap","message":"the grip's lean and size within about 1.5%: on the service rifle's photo an A2 grip stands about a degree nose-up of the Army drawing's side view with its top level (Aero's photo of its own: 1.7°), and the drawing's stated 1.275 across its front face is 0.05 more than the two photographed grips have there — need a straight side photo of a bare A2 grip with a scale in its plane, and the Army drawing's Section C-C (frame 2) read for the slot's floor and what the 1.275 spans"},{"level":"gap","where":"part cmmg-lower-parts-kit gap","message":"where the kit's weight sits: it is put at the middle of everything drawn, most of which is the grip, though most of the weight is the steel in the receiver — need a published weight for an A2 grip alone (the model is solid where the grip is hollow, so a density won't do); the grip and the guard then become lumps and the steel takes the rest"},{"level":"gap","where":"part cmmg-lower-parts-kit gap","message":"where CMMG's own trigger rests, and its hammer and disconnector — need a pin-framed side photo of a lower built with this kit; the Army's drawings 8448613 (hammer) and 8448635 (disconnector) for the two not drawn"},{"level":"gap","where":"part cmmg-safety-selector gap","message":"its weight: no page states one — need CMMG's or a seller's figure for 55CA741, or a scale reading of one"},{"level":"gap","where":"part cmmg-safety-selector gap","message":"any size of CMMG's own part: all are the Army drawing's — need a straight view of CMMG's selector along its axis and one edge-on, to hold the drawing's lever to it; its only photo is one three-quarter view"},{"level":"gap","where":"part daniel-defense-103-barrel gap","message":"Where the 10.3 in is measured from — need The maker's statement (its site refuses the reader), or a drawing: from the barrel's breech face, as taken, or from the closed bolt's face, an eighth further back. The maker's square-on picture is for the breech face by its thread's pitch (10.90 in end to end at 28 to the inch, against 10.801 and 10.675) and by its extension's diameter (10.80), though that second ruler reads 10.66 with the edges taken at their palest"},{"level":"gap","where":"part daniel-defense-103-barrel gap","message":"Its profile's diameters — need The maker's drawing or table: none is published. Each is a picture's reading against the .750 journal, ± 0.004 to 0.008 in"},{"level":"gap","where":"part daniel-defense-103-barrel gap","message":"The barrel extension's length — need This barrel's two pictures read it 1.00 to 1.03 in behind the flange's rear face where the reference CAD set's standard extension has 0.990: a drawing of the extension (8448550 isn't in the package), or a picture with a scale on it"},{"level":"gap","where":"part daniel-defense-103-barrel gap","message":"The gas port's diameter and place — need The maker's figures. A seller's title says .070 and a customer's review that the maker has shipped .070 and .082; its place is read off one picture turned 19° to the lens (± 0.03 in): 0.06 to 0.10 in ahead of where the catalog's mid-length barrels' ports and Aero's two tube lengths would put it, which a 10.3 measured from the bolt's face would take up"},{"level":"gap","where":"part daniel-defense-103-barrel gap","message":"The relief groove at the shoulder, the muzzle's crown and the edge breaks — need Close views square to the muzzle end with a scale in their plane: the sellers' pictures show them from 16 in and 20° off"},{"level":"gap","where":"part daniel-defense-103-barrel gap","message":"The extension's locking lugs and feed ramps, and the chamber's mouth — need The extension's drawing (8448550 isn't in the package): its lugs, slots and ramps are the reference CAD set's, a third-party model of a mil-spec part; hidden once the barrel is in a receiver"},{"level":"gap","where":"part daniel-defense-bcg gap","message":"Anything from Daniel Defense itself — need Its site refuses the reader (PLAN D59): every figure is a seller's. A page the user saves from their own browser, or the maker's words hosted elsewhere, would give its own"},{"level":"gap","where":"part daniel-defense-bcg gap","message":"A weight that was weighed — need Wing's 11.5 oz and Primary Arms' 11 oz are sellers' rows half an ounce apart, and the review repeats the round one; a scale reading of this group (a review's table) would settle it"},{"level":"gap","where":"part daniel-defense-bcg gap","message":"Anything of Daniel Defense's own shape — need No drawing or size is published; the model is the Army's carrier, checked against the photos by the serrations' count, the tail's diameter and the two side holes' places only. The lasered logo isn't drawn; the staking is drawn as a straight-sided notch through the key's wall, as the side view shows it, without the metal it pushes into the head"},{"level":"gap","where":"part daniel-defense-fixed-front-sight gap","message":"The length is a whole inch from one seller (Wing); the width and the height have no published figure on file (Modern Warriors' text, the discovery's lead, wasn't served to the harvester: 202, an empty body) — need A seller's table with the front sight's sizes in decimals, or the maker's"},{"level":"gap","where":"part daniel-defense-fixed-front-sight gap","message":"The serrations on the rear ramp: how many and how deep — need A count on Primary Arms' photo from behind (f0aba6d31478) or Wing's 55323"},{"level":"gap","where":"part daniel-defense-fixed-front-sight gap","message":"Mil-Spec+ Brown and Tornado Grey are sold only in the set and aren't offered: no colour matched — need make color-match on GRITR Outdoors' brown photos; a photograph (not a render) of the Tornado Grey set"},{"level":"gap","where":"part daniel-defense-fixed-front-sight gap","message":"danieldefense.com refuses the reader (D59): no maker's page, drawing or manual — need Pages of Daniel Defense's the user saves from their own browser"},{"level":"gap","where":"part daniel-defense-fixed-rear-sight gap","message":"The sight line's height as a maker's figure: no page states it (Wing's \"Center Height Over Rail: Rear: 1.54\"\" is the aperture's top); the patent's 1.363 and Wing's end-on photo's 1.41 differ — need A maker's or seller's figure for the aperture's centre over the rail, or a square side photo of the sight on a rail with the aperture's ring in profile"},{"level":"gap","where":"part daniel-defense-fixed-rear-sight gap","message":"The width's span (TLO's 1.24 in) and the overall height (TLO's 1.78 against the patent's 1.81 at the length's scale) — need A second seller's table, or a dimensioned drawing"},{"level":"gap","where":"part daniel-defense-fixed-rear-sight gap","message":"Mil-Spec+ Brown and Tornado Grey are sold only in the set and aren't offered: no colour matched — need make color-match on GRITR Outdoors' brown photos (5ae12c63efa9, f1fb888cfd05); a photograph of the Tornado Grey set"},{"level":"gap","where":"part daniel-defense-fixed-rear-sight gap","message":"danieldefense.com refuses the reader (D59): no maker's page, drawing or manual — need Pages of Daniel Defense's the user saves from their own browser"},{"level":"gap","where":"part dead-air-rxd22ti gap","message":"The front end square on: the ring's inside, its notches' size, the core's front face and its hole — need a photo straight into the front end"},{"level":"gap","where":"part dead-air-rxd22ti gap","message":"The core's flange flats, and the wrench sizes the manual names (1-1/16 in, 27 mm) against the tube's hex as read (0.97 in) — need Dead Air's drawing, or a view along the axis from the rear"},{"level":"gap","where":"part dead-air-rxd22ti gap","message":"The Burnt Bronze tube assembled, and its colour under the app's light — need a seller's photo of RXD22TiBB whole; then `make color-match`"},{"level":"gap","where":"part dead-air-xrf-brake gap","message":"The hex's flats, and which flat is where — need a view straight along the axis, or Dead Air's drawing; 0.75 in is assumed from the manual's wrench"},{"level":"gap","where":"part dead-air-xrf-brake gap","message":"The thread the suppressor screws onto: its size and pitch as the maker states them — need Dead Air's drawing or a page that names it; read on one photo at 0.814 in and 0.0375 in"},{"level":"gap","where":"part dead-air-xrf-brake gap","message":"The inside: how deep the barrel's thread runs, the lead-catching room and its front wall, how the port opens into it — need a section, or photos straight into both ends"},{"level":"gap","where":"part eotech-exps3 gap","message":"The reticle's height over the rail, as EOTECH states it — need No page or document on file states one (only \"lower 1/3 co-witness\" and \"7mm raised base\"): the window's centre is 1.86 in above the rail's top by the photos, the rail's top taken at the roof of the notch in the current rear cover, which the cross bolt's axis agrees with within a slot's depth; no view on file has the sight on a rail, and at 1.86 in an AR's own sights come up at the window's lower edge. A dimensioned drawing, or a photo of the sight on a rail from straight behind or straight from the side with the rail's slots in frame, would close it"},{"level":"gap","where":"part eotech-exps3 gap","message":"What the tan sight's lever and its housing are made of and finished in, and which of two looks the lever has — need No page on file names either. Primary Arms' photos (an older sight) have the lever an olive gold and its latch a bare grey; EOTECH's current pictures have both a redder bronze, in a light of their own. A page of EOTECH's that names the finishes, or a large photo of a current tan sight's left side on white, would settle it; the plate of the same metal round the adjustment nut wants an outline traced on the right side view before it is drawn"},{"level":"gap","where":"part eotech-exps3 gap","message":"The cross bolt's own size, and how far the jaws hook under the rail — need The manual's Figure 1 draws the base from below, undimensioned; the rear cover's notch in the view from behind is the only section of the channel on file. A view of the base from below, or from the front with the lever open, would give both"},{"level":"gap","where":"part eotech-g33 gap","message":"The optical axis's height over the rail from EOTECH itself. Its manual says only \"an absolute co-witness or lower-third co-witness height\"; the 47 mm with the riser (40 mm without) is one reviewer's, which EOTECH's pictures bear out within 1.3 mm. — need EOTECH's own centreline figure for the G33 on the STS mount, or a second independent reading of it."},{"level":"gap","where":"part eotech-g33 gap","message":"The mount set to open to the left (EOTECH: \"Position the mount on the optic mount interface (or riser) so it opens either to the left or right (based on preference).\"): the model has the one arrangement EOTECH pictures, opening to the right. — need A decision to offer it as a choice: drawn mirrored about the rail's middle, as EOTECH's manual says it is set up."},{"level":"gap","where":"part eotech-g33 gap","message":"The tan kit (G33.STSTAN): the magnifier tan, the mount black. — need A colour preset matched to EOTECH's tan (its EOTECH-G33-Tan-1.webp and T.REX's photos of it are on file; T.REX's read olive-grey on the body and tan on the tubes)."},{"level":"gap","where":"part eotech-g33 gap","message":"What the 2022 manual's 4.4 in (113 mm) length spans. EOTECH's page and catalogue say 4 in (102 mm), and its side views agree with the mount's published 1.66 in only at 4 in. — need A reviewer's rule on the part, or EOTECH's word."},{"level":"gap","where":"part eotech-g33 gap","message":"A view square across the magnifier's width. The rear views are close ones (their scale changes by 5% and more with depth), so the housing's width, the knob on its right and the hinge's place across the rifle are each good to about 0.05 in. — need A straight view from above or below, or a rear view from further off."},{"level":"gap","where":"part eotech-g45 gap","message":"The optical axis's height over the rail. No page states it: EOTECH's manual says only \"an absolute co-witness or lower-third co-witness height\". The 1.83 in drawn is the diopter ring's middle on EOTECH's side view over the rail's top where the same mount's clamp puts it, and that in turn rests on one reviewer's 47 mm for the G33. — need EOTECH's own centreline figure for the G45 on the STS mount with the riser, or a reviewer's rule on one."},{"level":"gap","where":"part eotech-g45 gap","message":"Anything across the magnifier: its body's width, where the horizontal knob's face is, its overall width (EOTECH: 2.3 in; the model 2.12). Every view on file is from the side or oblique. — need A straight view from above, from behind or from ahead (EOTECH's gallery has none for the G45)."},{"level":"gap","where":"part eotech-g45 gap","message":"What EOTECH's 3.9 in length spans: three side views have 3.75 to 3.83 in between the magnifier's two end faces. — need A reviewer's rule on the part, or EOTECH's word."},{"level":"gap","where":"part eotech-g45 gap","message":"The diopter ring's flutes: their number (20 drawn, from their spacing on two side views; 19 or 21 isn't excluded) and their depth (the G33's ring's, unread on this one). — need A view from behind, the ring's rear rim whole."},{"level":"gap","where":"part eotech-g45 gap","message":"The mount set to open to the left (EOTECH: \"Position the mount on the optic mount interface (or riser) so it opens either to the left or right (based on preference).\"): the model has the one arrangement EOTECH pictures, opening to the right. — need A decision to offer it as a choice: drawn mirrored about the rail's middle, as EOTECH's manual says it is set up."},{"level":"gap","where":"part eotech-g45 gap","message":"How deep the sunk panels in four of the collar's pads are (drawn as the pads' own relief, 0.027 in; the side views bracket it only from above), and the recess round each knob, which isn't drawn. — need A view along the housing where a panel meets the outline, or a close oblique one with a known width in it."},{"level":"gap","where":"part expo-arms-mlok-15-handguard interface mlok.reach_inside","message":"needs expo-arms-mlok-15-handguard.reach_inside"},{"level":"gap","where":"part expo-arms-mlok-15-handguard gap","message":"Where it seats on a receiver (its rear face is taken at the standard's front shoulder) — need A photo of it mounted on an upper whose lug holes show, or Primary Arms' instructions for it (none are published)"},{"level":"gap","where":"part expo-arms-mlok-15-handguard gap","message":"Its section: its width, the flats inside, the channel's roof — need A view down its length with its rail in frame (Primary Arms' three photos have none)"},{"level":"gap","where":"part expo-arms-mlok-15-handguard gap","message":"The room inside its faces before what runs under it (reach_inside: what an M-LOK accessory's nuts may take) — need The barrel's and the gas block's sizes under the slots: the build's, once those parts state them"},{"level":"gap","where":"part expo-arms-mlok-15-handguard gap","message":"Which weight is the handguard's: 13.2 oz on its page, 18.2 oz on the FDE one's, and neither says whether the barrel nut is counted — need A weighed figure with the nut said to be on or off"},{"level":"gap","where":"part expo-arms-mlok-15-handguard gap","message":"The FDE Cerakote variant (XP-GUARD15-FDE) — need A colour preset for Expo's FDE Cerakote, matched on Primary Arms' photos of it"},{"level":"gap","where":"part expo-arms-mlok-15-handguard gap","message":"Whether a low-profile gas block clears it — need A rule from Primary Arms' sentence (\"the generous internal diameter leaves room for a low-profile gas block\") once a gas block states its height over the bore"},{"level":"gap","where":"part expo-arms-stripped-upper checklist","message":"upper checklist: \"weight\" still missing"},{"level":"gap","where":"part expo-arms-stripped-upper gap","message":"Its weight — need A page that states one: Primary Arms' (the brand owner's) gives none, and no seller or reviewer on file does. Not estimated: a build with it says its total weight is unknown"},{"level":"gap","where":"part expo-arms-stripped-upper gap","message":"Its width, and how far its forward assist housing and deflector stand out — need An end or a top view with a known size in frame: the mil-spec forging's figures stand in"},{"level":"gap","where":"part expo-arms-stripped-upper gap","message":"A forward assist and a port door for it — need Those parts in the catalog: it is sold without them, and drawn without them"},{"level":"gap","where":"part faxon-16-pencil-barrel gap","message":"The section ahead of the gas block: .525 by Faxon's sentence, .50 by both photographs — need Faxon's print (its page says its figures are from it and doesn't publish it), or a caliper reading on a barrel; until then the photographs' figure is drawn and the maker's kept beside it (forward_od)"},{"level":"gap","where":"part faxon-16-pencil-barrel gap","message":"Where the 16.13 in is measured from — need Faxon's statement. Taken from the barrel's breech end (as the Army's drawing dimensions a barrel), three other published sizes land within a hundredth on the photo; from either of the two other faces they miss by 2 to 3%"},{"level":"gap","where":"part faxon-16-pencil-barrel gap","message":"The collar behind the journal and the long taper's two diameters — need Faxon's print: its sentence gives the journal and names a tapered body, no collar and no figures for the taper; they are the photo's (± 0.009 in)"},{"level":"gap","where":"part faxon-16-pencil-barrel gap","message":"The gas port's distance from the breech — need Faxon's figure (its page says only that mid-length gas \"puts the port about two inches farther from the chamber than carbine-length gas\"); it is read on an oblique close view, ± 0.04 in"},{"level":"gap","where":"part faxon-16-pencil-barrel gap","message":"The gas port's diameter: .081 by Faxon, .078 by Primary Arms and Impact Guns — need Nothing drawn turns on it; Faxon's own page is taken (gas_port_d keeps all three)"},{"level":"gap","where":"part faxon-16-pencil-barrel gap","message":"The target crown's width and depth, the extension's locking lugs and feed ramps, the chamber — need A straight view of the muzzle's face with a scale in its plane; the extension's drawing (8448550 isn't in the package)"},{"level":"gap","where":"part fn-p90-50-magazine gap","message":"Every size of it: no page (FN's, a seller's, a review's) gives one — need FN's or a seller's figures, or a square view from the side, the top and an end with a scale in the part's plane"},{"level":"gap","where":"part fn-p90-50-magazine gap","message":"Its weight empty (worked out from Wikipedia's two weights of a P90, ± 1.7 oz) — need FN's figure, or a review's weighing"},{"level":"gap","where":"part fn-p90-50-magazine gap","message":"The feed tower's bottom face (its bar and pockets) and the cap's lugs and feet in profile — need A view of the feed end square from below and one of the front end square on"},{"level":"gap","where":"part fn-p90-50-magazine gap","message":"The raised ring on the underside: where it stands across, its size and how far it stands proud (all assumed) — need A view of the underside square on, with the tower in it, and one of the ring in profile"},{"level":"gap","where":"part fn-p90-50-magazine gap","message":"The two long lines down the top face: grooves in it, or inner ribs seen through it — need A view along the top face at a grazing angle, or one of the front or rear end square on, where a groove would notch the outline"},{"level":"gap","where":"part geissele-139-chf-barrel gap","message":"Every diameter but the journal's, and every station along the barrel — need Geissele's own page or drawing (its site refuses the reader): all are read off one seller's close, yawed photo at 139 px to the inch, through a scale fixed at two stations: ± 0.008 in on a diameter and ± 0.03 to 0.04 on a station. A level photo taken from further off would do better"},{"level":"gap","where":"part geissele-139-chf-barrel gap","message":"Where the 13.9 in is measured from — need The maker's statement (taken from the barrel's breech end, as the Army's drawing dimensions a barrel; the photo by its own scales reads 0.18 in shorter end to end, which is nearer what a length from the bolt's face would be)"},{"level":"gap","where":"part geissele-139-chf-barrel gap","message":"The dimple under the journal: its place and depth; the slot along the collar: its depth — need Geissele's figures, or a level view of the underside and a close view of the collar's top with their edges on the silhouette"},{"level":"gap","where":"part geissele-139-chf-barrel gap","message":"The extension's locking lugs and feed ramps, the chamber's mouth, the muzzle's crown — need The extension's drawing (8448550 isn't in the package) and a close view of the muzzle: the extension's inside is the reference CAD set's, turned; hidden once the barrel is in a receiver"},{"level":"gap","where":"part geissele-139-chf-barrel gap","message":"Its steel — need The maker's own statement: sellers print \"Chrome Moly Vanadium Steel\", \"Chromoly steel\", \"Chromolly Steel\" and \"Steel\""},{"level":"gap","where":"part geissele-145-chf-barrel gap","message":"Every diameter but the journal's, and every station along the barrel — need Geissele's own page or drawing (its site refuses the reader): all are read off one seller's photo at 133 px to the inch, ± 0.007 in on a diameter and ± 0.03 on a station"},{"level":"gap","where":"part geissele-145-chf-barrel gap","message":"Where the 14.5 in is measured from — need The maker's statement (taken from the barrel's breech end, as the Army's drawing dimensions a barrel; the photo at its journal's scale reads 0.09 in shorter end to end, which is about what a length from the bolt's face would be)"},{"level":"gap","where":"part geissele-145-chf-barrel gap","message":"The gas port's own station — need A straight view of the barrel's top with a scale in its plane: it is drawn over the dimple, which Rooftop's rendering agrees with to 0.03 in"},{"level":"gap","where":"part geissele-145-chf-barrel gap","message":"The dimple under the journal: its depth; the notch in the collar: its width and depth — need Geissele's figures, or a close view of each with its edge on the silhouette"},{"level":"gap","where":"part geissele-145-chf-barrel gap","message":"The extension's locking lugs and feed ramps, the chamber's mouth, the muzzle's crown — need The extension's drawing (8448550 isn't in the package) and a close view of the muzzle: the extension's inside is the reference CAD set's, turned; hidden once the barrel is in a receiver"},{"level":"gap","where":"part geissele-145-chf-barrel gap","message":"Its steel — need The maker's own statement: sellers print \"Chrome moly vanadium steel\", \"4140 Chrome Moly Steel\" and (under another number) \"4150 CMV Steel\""},{"level":"gap","where":"part geissele-16-chf-barrel gap","message":"Every diameter but the journal's, and every station along the barrel — need Geissele's own page or drawing (its site refuses the reader): all are read off one seller's photo at 122 px to the inch, through a lens distortion of the photo's own, ± 0.008 in on a diameter and ± 0.03 to 0.04 on a station"},{"level":"gap","where":"part geissele-16-chf-barrel gap","message":"The barrel's length: 16 or 16.25 in, and where it is measured from — need The maker's statement, or a second page quoting its table: Primary Arms says 16, AR15Discounts' list 16.25, and the photo reads between them"},{"level":"gap","where":"part geissele-16-chf-barrel gap","message":"The gas port's own station and its diameter — need A straight view of the barrel's top with a scale in its plane, and a second seller's figure: the port is drawn over the dimple, at one page's .078"},{"level":"gap","where":"part geissele-16-chf-barrel gap","message":"The dimple's depth; the notch in the collar: its width and depth — need Geissele's figures, or a close view of each with its edge on the silhouette"},{"level":"gap","where":"part geissele-16-chf-barrel gap","message":"The extension's locking lugs and feed ramps, the chamber's mouth, the muzzle's crown — need The extension's drawing (8448550 isn't in the package) and a close view of the muzzle: the extension's inside is the reference CAD set's, turned; hidden once the barrel is in a receiver"},{"level":"gap","where":"part geissele-16-chf-barrel gap","message":"Its steel — need The maker's own statement: sellers print \"Chrome moly vanadium steel\" and \"4140 Chrome Moly Steel\""},{"level":"gap","where":"part geissele-mk16-105-handguard interface mlok.reach_inside","message":"needs geissele-mk16-105-handguard.reach_inside"},{"level":"gap","where":"part geissele-mk16-105-handguard interface mlok_lower.reach_inside","message":"needs geissele-mk16-105-handguard.reach_inside"},{"level":"gap","where":"part geissele-mk16-105-handguard interface mlok_upper.reach_inside","message":"needs geissele-mk16-105-handguard.reach_inside"},{"level":"gap","where":"part geissele-mk16-105-handguard interface mlok_bottom.reach_inside","message":"needs geissele-mk16-105-handguard.reach_inside"},{"level":"gap","where":"part geissele-mk16-105-handguard gap","message":"The M-LOK slots on its underside: how many, and where they begin (sellers: \"M-LOK slots on every quadrant\"; drawn and offered as the side rows' five at the side rows' stations, assumed) — need A photo of it from below, or into its muzzle end: no view on file shows the bottom face"},{"level":"gap","where":"part geissele-mk16-105-handguard gap","message":"Where it stops on the receiver (rear_face_x: drawn against the front shoulder with no gap) — need A photo of it mounted on a mil-spec upper, or the maker's instruction sheet from a page that may be read"},{"level":"gap","where":"part geissele-mk16-105-handguard gap","message":"Its section square on at this length (the faces' lean, the bottom flat and the troughs inside are the 13.5 in rail's readings; the rear end's round bore and the neck are the 15 in rail's readings of a shorter rail) — need A view square on an end of the 10.5 in rail with a known size in frame"},{"level":"gap","where":"part geissele-mk16-105-handguard gap","message":"Its weight: sellers give 11 oz (12.6 with the nut) and 11.2 oz (12.84) — need The maker's own figure, from a page that may be read"},{"level":"gap","where":"part geissele-mk16-105-handguard gap","message":"The room inside its faces before the barrel (reach_inside: what an M-LOK accessory's nuts may take) — need The barrel's and the gas block's size under it, from the parts a build puts there"},{"level":"gap","where":"part geissele-mk16-105-handguard gap","message":"Its Desert Dirt Color as the maker means it (the preset is one seller's 15 in rail; the same seller's rail of this length is a lighter, more orange tan, and the maker says the colour varies from rail to rail) — need The maker's own pictures of the DDC rail, from a page that may be read"},{"level":"gap","where":"part geissele-mk16-135-handguard interface mlok.reach_inside","message":"needs geissele-mk16-135-handguard.reach_inside"},{"level":"gap","where":"part geissele-mk16-135-handguard interface mlok_lower.reach_inside","message":"needs geissele-mk16-135-handguard.reach_inside"},{"level":"gap","where":"part geissele-mk16-135-handguard interface mlok_upper.reach_inside","message":"needs geissele-mk16-135-handguard.reach_inside"},{"level":"gap","where":"part geissele-mk16-135-handguard interface mlok_bottom.reach_inside","message":"needs geissele-mk16-135-handguard.reach_inside"},{"level":"gap","where":"part geissele-mk16-135-handguard gap","message":"The M-LOK slots on the rear half of its underside: how many the row has (its foremost four are seen from inside the muzzle end; drawn and offered as the side rows' seven at the side rows' stations) — need A photo of it from below: no view on file shows the bottom face"},{"level":"gap","where":"part geissele-mk16-135-handguard gap","message":"Where it stops on the receiver (rear_face_x: drawn against the front shoulder with no gap) — need A photo of it mounted on a mil-spec upper, or the maker's instruction sheet from a page that may be read"},{"level":"gap","where":"part geissele-mk16-135-handguard gap","message":"Its section behind the muzzle end (the trough inside the bottom is seen at the muzzle end only; the rear end's round bore and the neck are the 15 in rail's readings of a shorter rail) — need A view into its rear end with a known size in frame"},{"level":"gap","where":"part geissele-mk16-135-handguard gap","message":"The room inside its faces before the barrel (reach_inside: what an M-LOK accessory's nuts may take) — need The barrel's and the gas block's size under it, from the parts a build puts there"},{"level":"gap","where":"part geissele-mk16-135-handguard gap","message":"Its Desert Dirt Color as the maker means it (the preset is one seller's rail; another seller's rail of this length is a yellower tan, and the maker says the colour varies from rail to rail) — need The maker's own pictures of the DDC rail, from a page that may be read"},{"level":"gap","where":"part geissele-mk16-15-handguard interface mlok.reach_inside","message":"needs geissele-mk16-15-handguard.reach_inside"},{"level":"gap","where":"part geissele-mk16-15-handguard interface mlok_lower.reach_inside","message":"needs geissele-mk16-15-handguard.reach_inside"},{"level":"gap","where":"part geissele-mk16-15-handguard interface mlok_upper.reach_inside","message":"needs geissele-mk16-15-handguard.reach_inside"},{"level":"gap","where":"part geissele-mk16-15-handguard interface mlok_bottom.reach_inside","message":"needs geissele-mk16-15-handguard.reach_inside"},{"level":"gap","where":"part geissele-mk16-15-handguard gap","message":"The M-LOK slots on its underside: how many, and where they begin (sellers: \"M-LOK slots on every quadrant\"; drawn and offered as the side rows' eight at the side rows' stations, assumed) — need A photo of it from below: no view on file shows the bottom face"},{"level":"gap","where":"part geissele-mk16-15-handguard gap","message":"Where it stops on the receiver (rear_face_x: drawn against the front shoulder with no gap) — need A photo of it mounted on a mil-spec upper, or the maker's instruction sheet from a page that may be read"},{"level":"gap","where":"part geissele-mk16-15-handguard gap","message":"Its section square on at this length (the faces' angle, the neck's width, the walls) — need An end view of the 15 in rail with a known size in frame; the only near end-on view is of a shorter rail, 504 px wide"},{"level":"gap","where":"part geissele-mk16-15-handguard gap","message":"Its weight: sellers give 15.6 oz (17.1 with the nut) and 14.2 oz (15.8) — need The maker's own figure, from a page that may be read"},{"level":"gap","where":"part geissele-mk16-15-handguard gap","message":"The room inside its faces before the barrel (reach_inside: what an M-LOK accessory's nuts may take) — need The barrel's and the gas block's size under it, from the parts a build puts there"},{"level":"gap","where":"part geissele-mk16-15-handguard gap","message":"Its Desert Dirt Color as the maker means it (05-792S is matched to one seller's rail; the maker says the colour varies from rail to rail) — need The maker's own pictures of the DDC rail, from a page that may be read"},{"level":"gap","where":"part geissele-premium-mil-spec-buffer-tube-assembly-castle-nut gap","message":"What it is: its maker, its number, its steel and its finish — need Geissele's own page of the assembly (geissele.com refuses the reader: one the user saves), or a seller's page that names the nut"},{"level":"gap","where":"part geissele-premium-mil-spec-buffer-tube-assembly-castle-nut gap","message":"Its thickness — need a photo of the nut square from the side, or on the tube with the tube square to the lens"},{"level":"gap","where":"part geissele-premium-mil-spec-buffer-tube-assembly-end-plate gap","message":"What it is: its maker, its number, its steel and its finish — need Geissele's own page of the assembly (geissele.com refuses the reader: one the user saves), or a seller's page that names the plate"},{"level":"gap","where":"part geissele-premium-mil-spec-buffer-tube-assembly-end-plate gap","message":"Its sizes — need a square-on picture of the plate with a scale: every size here is the reference model's mil-spec plate, which the photos on file agree with"},{"level":"gap","where":"part geissele-premium-mil-spec-buffer-tube gap","message":"Whether Geissele still makes the gray (08-162G) — need Geissele's own page of the tube (geissele.com refuses the reader: one the user saves from their browser), or a dealer's page that says it is current or discontinued"},{"level":"gap","where":"part geissele-premium-mil-spec-buffer-tube gap","message":"Every size of Geissele's own: read on Primary Arms' two studio photos (a side view and an underside), each scaled by the tube itself — need a drawing of Geissele's tube, or a third photo square to the rail's side with a known size in its plane"},{"level":"gap","where":"part geissele-premium-mil-spec-buffer-tube gap","message":"The rear end, the channel's depth, the holes' depth and what is in their floors — need a photo of the rear end square on, and one of the rail's underside along it"},{"level":"gap","where":"part geissele-premium-mil-spec-buffer-tube gap","message":"The colours rest on one photograph each, the gray on Geissele's own studio picture of one tube — need a second studio's photograph of each colour with a known neutral in frame; the gray varies from lot to lot by Charlie's own picture of five"},{"level":"gap","where":"part geissele-ssa-e gap","message":"The bosses' span across the trigger and across the hammer (drawn at a mil-spec trigger's) — need A view square to the group's top or front, or the maker's sheet for the SSA-E (on the maker's site, which isn't read)"},{"level":"gap","where":"part geissele-ssa-e gap","message":"The weight: three sellers state 2.2, 2.5 and 3.2 oz and none says what was weighed — need The maker's figure, or a reviewer's on a scale with what was on it"},{"level":"gap","where":"part geissele-ssa-e gap","message":"The outlines' scale: the two pins' ends as far apart as a receiver holds them. Two things read 3% small at it and say the outline may be that much small: the pins' own ends (0.149 in for .154, dark discs on a dark ground) and the bow's tip (1.40 in below the pin for the Army's own trigger's 1.45 ± .02, if an M4 bow is the Army's). A third reading, the pins lying beside the trigger in BCM's parts view (33.0 px across for .154 where the trigger is 409.8 px long), has it 1.4% small, give or take 2.4%. The pocket and the slot take it either way — need The group in a lower, square to the side (the lower's own pins give the scale), or a published length of any piece"},{"level":"gap","where":"part geissele-ssa-e gap","message":"A photo of it installed, square to the side with both pins in frame: the rest angle is the group's as pictured out of a rifle — need A seller's or reviewer's side view of a lower with the SSA-E in it"},{"level":"gap","where":"part geissele-ssa-e gap","message":"The trigger's top under the disconnector and the spring's coil, the bevels on the block, the bow's rounding across — need The trigger alone square to its side and to its front (BCM's parts view is from above)"},{"level":"gap","where":"part geissele-super-42-h1 gap","message":"The maker's own figures — need Geissele's page or drawing for the set, saved by the user from their browser: the site isn't read (D59), and every size here is an owner's or the patent's"},{"level":"gap","where":"part geissele-super-42-h2 gap","message":"The maker's own figures — need Geissele's page or drawing for the set, saved by the user from their browser: the site isn't read (D59), and every size here is an owner's or the patent's"},{"level":"gap","where":"part geissele-super-42-h3 gap","message":"The maker's own figures — need Geissele's page or drawing for the set, saved by the user from their browser: the site isn't read (D59), and every size here is an owner's or the patent's"},{"level":"gap","where":"part geissele-super-duty-stripped-lower gap","message":"its weight: no page read publishes one (Primary Arms, Blackstone, Aegis Cerakote); geissele.com refuses the reader — need a seller's or reviewer's page that weighs the stripped receiver; the figure on file is its model's metal"},{"level":"gap","where":"part geissele-super-duty-stripped-lower gap","message":"how far the roll on the well's right wall stands out (the Workhorse's 0.80 from the centre is drawn), and how far the two oblong pads by the selector and the rib beside the fence stand off their faces (assumed: 0.03 and 0.04) — need a view along the receiver from ahead or behind, or a close oblique with a known edge beside them"},{"level":"gap","where":"part geissele-super-duty-stripped-lower gap","message":"OD green: seen only as Geissele's receiver set (05-1171ODG), with no page read selling the lower alone in it — need a seller's page for an OD green Super Duty lower with its number and a photo"},{"level":"gap","where":"part geissele-super-duty-stripped-upper gap","message":"A number of its own and a price — need A page that sells the bare upper: it is sold in the Super Duty Receiver Set (05-1171B, 05-1171S) with its lower, which is where its offers belong (a kit), and the assembled 05-3201B is another product"},{"level":"gap","where":"part geissele-super-duty-stripped-upper gap","message":"Its weight as published — need A page or a review that weighs it: none states one; it is weighed by its metal"},{"level":"gap","where":"part geissele-super-duty-stripped-upper gap","message":"Its width, its left side's own figures, and how far its forward assist housing and deflector stand out — need An end or a top view with a known size in frame, and the left photo measured: the mil-spec forging's figures stand in"},{"level":"gap","where":"part geissele-super-duty-stripped-upper gap","message":"Its own lugs — need A photo of the upper off its lower from the side: every photo on file has it on the lower, and the reference model's lugs stand in"},{"level":"gap","where":"part geissele-super-duty-stripped-upper gap","message":"A forward assist and a port door for it — need Those parts in the catalog: it is sold without them, and drawn without them"},{"level":"gap","where":"part geissele-super-precision-micro-193 gap","message":"Geissele's own drawing, figures and instruction sheet — need geissele.com refuses the reader: a drawing of this height would replace the photos' readings and the sibling's photos used for its end outline and its top"},{"level":"gap","where":"part geissele-super-precision-micro-193 gap","message":"Which dot the 1.93 in is for — need A page that names it: Primary Arms titles the mount for the T2, Geissele's text names the T1"},{"level":"gap","where":"part geissele-super-precision-micro-193 gap","message":"Where on the rail it goes — need A maker's sentence (receiver only, not across the rail's seam): none on any page read"},{"level":"gap","where":"part geissele-super-precision-micro-absolute gap","message":"Geissele's own drawing, figures and instruction sheet — need geissele.com refuses the reader: its spec page and instructions (the dot's screws and their torque) would replace the sellers' quotations and the drawing's readings"},{"level":"gap","where":"part geissele-super-precision-micro-absolute gap","message":"Which dot the 1.41 in is for — need A page that names it: Primary Arms titles the mount for the T2, Geissele's text names the T1; the deck's height is the 1.41 less the T-2's own axis over its base, and a T-1 is taken to stand as high"},{"level":"gap","where":"part geissele-super-precision-micro-absolute gap","message":"The weight as drawn against Geissele's — need The mount weighed, or a second page of Geissele's 2 oz: as drawn it is 36% over it, and a European seller's 79 g agrees with the drawing"},{"level":"gap","where":"part geissele-super-precision-micro-absolute gap","message":"Where on the rail it goes — need A maker's sentence (receiver only, not across the rail's seam): none on any page read"},{"level":"gap","where":"part geissele-super-precision-micro-lower-13 gap","message":"This height's height — need Geissele's own figure, or a drawing of this height: its sellers say 1.59 (Primary Arms) and 1.70 in to the optic's centerline (Rooftop Defense), and its own photos put a T-2 at about 1.47 to 1.50"},{"level":"gap","where":"part geissele-super-precision-micro-lower-13 gap","message":"Geissele's own drawing, figures and instruction sheet — need geissele.com refuses the reader: its spec page and instructions (the dot's screws and their torque) would replace the sellers' quotations and the photos' readings"},{"level":"gap","where":"part geissele-super-precision-micro-lower-13 gap","message":"Which dot the height is for — need A page that names it: Primary Arms titles the mount for the T2, Geissele's text names the T1"},{"level":"gap","where":"part geissele-super-precision-micro-lower-13 gap","message":"Where on the rail it goes — need A maker's sentence (receiver only, not across the rail's seam): none on any page read"},{"level":"gap","where":"part guntec-ar15-carbine-buffer gap","message":"Its own sizes — need Guntec's figures: its page states none; its length is two photographs' (3.42 in; Guntec's own picture, 7c97d3ec96e9, is an oblique and isn't read), its diameters and its head the standard's"},{"level":"gap","where":"part guntec-ar15-castle-nut gap","message":"Its sizes — need Guntec's figures: every size here is read on Cheaper Than Dirt's photo (its own thread or its own diameter as the scale) and checked on Redcon1's"},{"level":"gap","where":"part guntec-ar15-castle-nut gap","message":"Its front face — need A photo of the nut's front face: whether it has staking notches"},{"level":"gap","where":"part guntec-ar15-chrome-silicon-buffer-spring gap","message":"Its wire and its weight — need Guntec's figures (its pages refuse the reader: the user's saved copy of the set's page): the wire is the standard's, and 1.98 oz is worked out from it and the coils"},{"level":"gap","where":"part guntec-ar15-chrome-silicon-buffer-spring gap","message":"Its free length — need Guntec's figure: Redcon1 Tactical's spec table says 11 in, Guntec's 2019 picture of the set reads 12.1"},{"level":"gap","where":"part guntec-ar15-chrome-silicon-buffer-spring gap","message":"Sold alone? — need A page that ties it to a Guntec spring sold alone: a search names an 'AR-15 Chrome Car Stock Spring' (CH-SPR, \"Chrome/Teflon Coated\") on Guntec's site, which refuses the reader, and at OpticsPlanet, whose page gave the reader no product"},{"level":"gap","where":"part guntec-ar15-end-plate gap","message":"Its sizes — need Guntec's figures, or a square-on picture of the plate with a scale: every size here is the reference model's mil-spec plate, which Guntec's pictures agree with to their two or three hundredths"},{"level":"gap","where":"part guntec-ar15-heavy-duty-castle-nut gap","message":"Its front face notches' count — need A picture of its front face whole (the one on file shows its near half)"},{"level":"gap","where":"part guntec-ar15-mil-spec-buffer-tube-gen-2 gap","message":"The notch at the mouth's rim (\"Notch Cut Out For Buffer Detent To Engage\"): Guntec's two close-ups of the black tube (12b14516ed50, 0979efec9f6c) show it, small and square, and a slot through the thread's crests beside it; the model has the standard's key slot and no notch in the rim — need the notch read on those close-ups against the thread's pitch (a known size in their plane), or a view of the mouth square on"},{"level":"gap","where":"part guntec-ar15-mil-spec-buffer-tube-gen-2 gap","message":"The weight: Guntec states 3.3 oz (and 3.4 as the black tube's Product Weight), the metal worked out from the mil-spec sizes is 3.6 — need a review that weighs the tube alone, or the wall's and the channel's own sizes"},{"level":"gap","where":"part guntec-ar15-mil-spec-buffer-tube-gen-2 gap","message":"The holes' size and place, the channel's width and depth, and the rear end — need a photograph of the underside and the rear end square on, with a known size in frame"},{"level":"gap","where":"part guntec-ar15-mil-spec-buffer-tube-gen-2 gap","message":"Every colour rests on one studio's photographs and a treatment that takes the clear anodize for neutral grey and the studio's cut-out white ground for its exposure: nothing on file checks either — need a second studio's photograph of the tube alone in any colour, with a neutral (a black end plate, a grey card) in frame"},{"level":"gap","where":"part guntec-ar15-stainless-carbine-buffer gap","message":"Its inside — need Guntec's figure or a section: \"One Solid Unit\" at 3.2 oz is hollow by about half its outside's volume"},{"level":"gap","where":"part guntec-ar15-stainless-carbine-buffer gap","message":"Its own sizes — need Guntec's figures: \"Mil-Spec Dimensions\" gives it the standard's"},{"level":"gap","where":"part hexmag-series-2-ar15-30 checklist","message":"magazine checklist: \"body_height\" still missing"},{"level":"gap","where":"part hexmag-series-2-ar15-30 checklist","message":"magazine checklist: \"feed_lip_block_height\" still missing"},{"level":"gap","where":"part hexmag-series-2-ar15-30 gap","message":"A square view of the Series 2 from its rear or its front, and a figure of its own that fixes the scale: the patent's rear elevation (2013) is the section, and the scale is the well's (the top section reaching the well's front wall from the catalog's seat), not a reading of the magazine — need A photograph of HX30-AR15S2 end on, or Hexmag's own drawing"},{"level":"gap","where":"part hexmag-series-2-ar15-30 gap","message":"How far the HEXTURE panels stand out of their grooves, how deep the stripper-clip guides and the HexID's pocket are (assumed 0.03, 0.04 and 0.05 in) — need A view along a side from close by with a panel's edge in profile, or Hexmag's figure"},{"level":"gap","where":"part hexmag-series-2-ar15-30 gap","message":"What Hexmag's 7.5, 2.66 and 1.125 in are of: at the scale the well gives (7.366 tall) the floorplate is 1.085 wide and about 2.65 long along its own lean, and the top section 2.53 from the spine to the front — need Hexmag's drawing, or a seller's table of the magazine's sizes with what each spans"},{"level":"gap","where":"part hexmag-series-2-ar15-30 gap","message":"The gray's colour: the two photographs of HX30-AR15S2-GRY on file read 33 levels apart on the same flat (Blackstone's slate #5d6169, AmmunitionStore's charcoal #3c413a); Hexmag's gallery has the black one only — need Hexmag's own photograph of the gray one, or one of it beside a black or an FDE one under one light"},{"level":"gap","where":"part hexmag-series-2-ar15-30 gap","message":"The block under the catch window (not drawn): the rear elevation has it 0.049 in out of a side that is as wide as a well already — need A view of the Series 2 from its front or rear with the left side in profile at the window"},{"level":"gap","where":"part holosun-aro-163-mount gap","message":"The clamp's two ends: drawn as one surface falling straight to each end. The side photos show a dark round-ended notch in it at each end, the two obliques a pocket stepped down into its middle, and Holosun's front and rear views a dark face nearly the clamp's width with a lighter ledge under it over the rail. The lug under the clamp's roof and the two slits down from the nut's pocket aren't drawn either. — need A camera fitted to Holosun's front and rear views or to one of the two obliques on file; or a view of the mount from straight above."},{"level":"gap","where":"part holosun-aro-163-mount gap","message":"The deck plate: its lips, its four holes and its recoil key — need A straight view of the mount alone from the side and from above; Holosun's two pictures of it alone are from above and a quarter"},{"level":"gap","where":"part holosun-aro-163-mount gap","message":"The 1.05 in low mount the ARO comes with (Holosun's page: \"Included Mounts 1.63\" Mount 1.05\" Mount\") — need Any photograph of it, alone or with the sight on it: none is on file, so it isn't a part (D102)"},{"level":"gap","where":"part holosun-aro-163-mount gap","message":"The clamp's heights: the two side photos' cameras have each jaw's face 0.197 in over the rail at the bolt and the clamp's top 0.28; the user's rear view has 0.243 and 0.35. Drawn at the first. — need A straight view of the mount from the side with the rail in it."},{"level":"gap","where":"part holosun-aro-163-mount gap","message":"The cross bolt's height: Holosun's two side photos have its axis at the rail's top (0.015 in over it), the user's rear view 0.08 over it. Drawn at the first. — need A straight view of the mount from the side or from behind with the rail in it."},{"level":"gap","where":"part holosun-aro gap","message":"How deep the flutes, the HOLOSUN panels and the buttons' grooves are sunk, and how far the cover, its screws' heads and the caps stand: drawn at 0.02 in or at what the rear view's outline has, none of them seen in profile. — need A camera fitted to one of the two obliques on file (5ec56fffa262 at 2200 px, d968cfc95219), which show them from a quarter; or a view from above."},{"level":"gap","where":"part holosun-aro gap","message":"The left flank's raised panel and the two small pads beside the HOLOSUN panel on that side, in Holosun's left photo (3233645ac025): not drawn. — need Their outlines read through that photo's camera, and how far they stand from a view that shows it."},{"level":"gap","where":"part holosun-aro gap","message":"Whether the round body is wider than the objective's bezel: the rear view has one circle for both (1.20 in), the side photos have the bezel at 1.17. — need A straight view from the front, or from above."},{"level":"gap","where":"part holosun-eps-carry gap","message":"Holosun's US product photos and its manual (cdn.prod.website-files.com) — need That host's robots.txt answered 403 on 2026-11-06 and the harvester left it alone; the EU shop's photos are of the same sight (its serial on the left side)."},{"level":"gap","where":"part holosun-eps-carry gap","message":"The hood's section between the front and rear faces (what the window's tunnel is inside, how thick the walls are) — need A view through the window from a quarter, or a section; drawn as a straight tunnel of the window's size."},{"level":"gap","where":"part holosun-hm3x gap","message":"How the mount is set to swing to the left. Holosun's page calls it ambidextrous; the manual on file draws it swinging to the right and says nothing of turning it round. — need Holosun's instructions for reversing the mount, or a picture of one set up left-handed."},{"level":"gap","where":"part holosun-hm3x gap","message":"How much of the base's length its clamp's jaws grip, and where its recoil lugs are. The interface gives the mount the drawing's whole 1.93 in of rail, which is what it takes of the rail's length (that figure runs from the front knuckle to the adjustment tool's knob, both over the rail's right edge); the base is 1.73 in long and the rail channel is drawn the length of it. The picture of the magnifier from below (3bcb120eaf6e) has the left jaw in two stretches with the moving jaw between them, and two lugs in the channel's roof: taken from close and not square on, nothing of them is read. — need A view of the mount's underside square on, with the jaws and the recoil lugs in it."},{"level":"gap","where":"part holosun-hm3x gap","message":"How deep the eyepiece ring's flutes are: they are closed at both ends, so no rim shows them in outline. Drawn as deep as the objective ring's, a hundredth of an inch. — need A view of the eyepiece ring from its end and a little to one side, or a close one across its top, where a flute shows against the background."},{"level":"gap","where":"part holosun-hm3x gap","message":"The lines of the panels along the housing's flanks and top: seen in every photo of either side and in the drawing's side view, not drawn. Where they are is read (2026-10-19, the drawing's side view at its 214.1 px/in, from the axis): three rows a flank, each from the housing's front, 0.645 in ahead of the base's middle, to 2.183 in behind it with round rear ends; the upper from 0.66 to 0.265 in over the axis, the middle (the oval's row, a pad ahead of the oval to 0.262 in ahead and one behind it from 1.163 behind) from 0.162 over to 0.154 under, the lower from 0.26 to 0.653 under; between them two bands 0.10 in wide that run the housing's length. How far any of it stands is not: on Primary Arms' photo of the left side (lit from above) each edge is a line a few thousandths of an inch wide with light on both sides of it, not a lit or a shadowed wall, and the drawing's end view has the flank's silhouette a round within its trace's hundredth of an inch at those heights. Whatever relief there is is under a hundredth of an inch (under half a pixel where a whole rifle is drawn, a pixel and a half at a close look), and which side of each edge stands proud isn't settled: not drawn rather than drawn either way. — need A close view along the flank from an end, or across the top, where a panel's edge shows as a step against the background."},{"level":"gap","where":"part holosun-hm3x gap","message":"How deep the slanted pockets in the foot's sides are: no view has one in profile. Drawn a fiftieth of an inch deep. — need A view of the foot from the front or from below, square on, where a pocket notches the side's edge."},{"level":"gap","where":"part holosun-hm3x gap","message":"How far the right flank's oval stands off the housing, and how deep either oval's field is: the drawing's end view has the left one edge on (0.739 in from the axis) and the adjuster's cap in front of the right one. Drawn with the left one's figures. — need A view from the eyepiece end, square on, or along the right flank."},{"level":"gap","where":"part holosun-hm3x gap","message":"The strip in the base's top under the flip plate, and the base's top with the magnifier swung aside: only the manual's two line drawings show it, read by proportion. — need A photo of the mount from above with the magnifier swung aside."},{"level":"gap","where":"part holosun-hm3x gap","message":"Where the housing comes to rest when swung aside, to better than a twentieth of an inch: it follows from the hinge's place, read on two pictures. — need A picture of the magnifier swung aside, square on from behind or from the front."},{"level":"gap","where":"part holosun-hs510c gap","message":"A straight view from above — need The solar cell's size, where the elevation screw stands on the deck and the ribbed floor under the hood: the plan on file is a photo from below, which shows only the widest outline at each station."},{"level":"gap","where":"part holosun-hs510c gap","message":"A second straight view of the left side — need The buttons' pad, the two screws, the clamp's bolt and the opening under the housing are placed from one seller's straight photo of the left side (Primary Arms), which the drawing's two sizes fit to 2%; it reads the foot 0.06 in longer than the drawing does."},{"level":"gap","where":"part holosun-hs510c gap","message":"The deck's facets across the sight — need A straight view from behind and one from above: how far the rear corners' facets and the top edges' chamfers cut across is assumed (45 degrees each); only their edges on the side wall are in a straight view."},{"level":"gap","where":"part holosun-hs510c gap","message":"How deep the glass sits and how it leans — need A section, or a straight side view through the hood: the pane is drawn just behind the front face and parallel to it."},{"level":"gap","where":"part holosun-hs510c gap","message":"What Holosun's 215 g is made of — need The body (4.94 oz, 140 g) and the mount (45 g) as published add to 185 g; a scale reading of the sight with and without its battery and mount would settle the 30 g between."},{"level":"gap","where":"part holosun-hs510c gap","message":"What the battery tray's plate and the buttons' pad are made of — need A page or a manual that names them: the pad is drawn as rubber and the tray in the housing's finish, each by its look in the photos"},{"level":"gap","where":"part holosun-hs510c gap","message":"Holosun's own photos of the FDE sight — need Its colours are matched to one distributor's three photographs (Impact Guns' and Sportsman's Warehouse's pages show the same set): Holosun's own are on a host whose robots.txt can't be read, and are left alone. A second photographer's FDE sight would check the tan, the tray's and the pad's."},{"level":"gap","where":"part huxwrx-flash-hider-qd-556 gap","message":"The slots' count and the core's end, on a view that shows the whole turn — need a photo straight on at the muzzle end (none at the maker or at eight sellers); six slots is counted from their spacing on a side view"},{"level":"gap","where":"part huxwrx-flash-hider-qd-556 gap","message":"The suppressor's thread: its size, how deep it is cut, its form — need the maker's drawing of the QD mount, or a straight, sharp side photo of the thread against a scale (the photo on file is soft at the grooves)"},{"level":"gap","where":"part huxwrx-flash-hider-qd-556 gap","message":"Where a suppressor's rear face stands on it, against the suppressors' published added lengths — need a photo of a FLOW suppressor on a rifle, square from the side, that shows the hex behind it (or doesn't): the maker's rendering shows it, and the published added lengths would have the suppressor 0.17 to 0.21 in further back"},{"level":"gap","where":"part huxwrx-flash-hider-qd-556 gap","message":"Weight and diameter from the maker — need HUXWRX states neither; three sellers give 3.3 oz and one 1.20 in"},{"level":"gap","where":"part huxwrx-flash-hider-qd-556 gap","message":"Its steel and its finish in the maker's words — need a page that names them: 'Steel' and 'Black' are one seller's"},{"level":"gap","where":"part huxwrx-flow-556-ti gap","message":"The cap's pockets: their depth and their curved floors — need a second view of the muzzle end from the side, close: Mile High's straight-on photo gives their plan and not their depth"},{"level":"gap","where":"part huxwrx-flow-556-ti gap","message":"The mount's socket: its thread, its taper and its depth — need the maker's drawing of the QD mount; it is drawn to fit the flash hider"},{"level":"gap","where":"part huxwrx-flow-556-ti gap","message":"How far the can's front stands ahead of the muzzle: the pair as drawn against the maker's 6.1 in — need a photo of the can on a rifle square from the side, with the barrel's shoulder in view"},{"level":"gap","where":"part huxwrx-flow-556-ti gap","message":"5.45 in the maker's list of calibers — need a name for it in data/cartridges.yaml"},{"level":"gap","where":"part huxwrx-flow-556k gap","message":"The cap's pockets: their depth, their floors and how they open into the core — need a sharp photo straight on at the muzzle end of the 556K (the only one on file is of the 556 Ti) and one square from the side across the cap"},{"level":"gap","where":"part huxwrx-flow-556k gap","message":"The mount's socket: its thread, its taper and its depth — need the maker's drawing of the QD mount; it is drawn to fit the flash hider"},{"level":"gap","where":"part huxwrx-flow-556k gap","message":"Weight: 12.9 oz at the maker, 11.8 and 11.9 oz at two sellers — need a reviewer's own scale reading, or the maker's word on what the lighter figure is"},{"level":"gap","where":"part huxwrx-flow-556k gap","message":"How far the can's front stands ahead of the muzzle: the pair as drawn against the maker's 4.9 in — need a photo of the can on a rifle square from the side, with the barrel's shoulder in view"},{"level":"gap","where":"part huxwrx-flow-556k gap","message":"5.45 in the maker's list of calibers — need a name for it in data/cartridges.yaml"},{"level":"gap","where":"part jp-silent-captured-spring-gen2-h2 gap","message":"A square side view of the H2 — need A seller's side photo of this number (MidwayUSA's and Silencer Shop's pages have none on file): its spring's outside and wire, and any size that differs from the standard's"},{"level":"gap","where":"part jp-silent-captured-spring-gen2-h3 gap","message":"A photograph of the H3 — need A seller's photo of this number: JP's own picture of it is its H2 picture with the steel weight darkened"},{"level":"gap","where":"part jp-silent-captured-spring-gen2-h3 gap","message":"A seller — need No seller in data/vendors.yaml carries JPSCS2-15H3 (web search, 2026-10-18); JP's own store sells it ($233.95 on its page) and its page carries no offer markup"},{"level":"gap","where":"part jp-silent-captured-spring-gen2 gap","message":"The maker's own sizes — need JP publishes no length or diameter of the unit: a drawing or a measured review would replace the photo readings (every diameter is one photo's, ±1.6%)"},{"level":"gap","where":"part jp-silent-captured-spring-gen2 gap","message":"The weights' bore and the slider's tube — need A photo of the slider taken apart (JP's weights sheet describes it, and shows none on file): the model's are assumed for the weight"},{"level":"gap","where":"part kynshot-rb5000 gap","message":"The head's flats seen face-on — need a view looking along the axis at the head's face, to count the flats round the whole turn and read their depth square (two are seen at once from above)"},{"level":"gap","where":"part kynshot-rb5000 gap","message":"What it is inside — need the body's bore and the damper's parts: the maker's patent US 10,100,896 B2 (engraved on the part) draws its mechanism, not this product's sizes; nothing is drawn of the inside"},{"level":"gap","where":"part kynshot-rb5000 gap","message":"Its stroke against its rod — need a photo of it pushed in, or the maker's word: the rod stands out 0.32 in at rest, and the maker's two lengths differ by 0.40"},{"level":"gap","where":"part kynshot-rb5000hp gap","message":"The head's flats seen face-on — need a view looking along the axis at the head's face, to count the flats round the whole turn and read their depth square"},{"level":"gap","where":"part kynshot-rb5000hp gap","message":"What it is inside — need the body's bore and the damper's parts: nothing is drawn of the inside"},{"level":"gap","where":"part kynshot-rb5000hp gap","message":"Its stroke against its rod — need a photo of it pushed in, or the maker's word: the rod stands out 0.33 in at rest, and the maker's two lengths differ by 0.44"},{"level":"gap","where":"part kynshot-rb5000hp gap","message":"A review of its own — need the reviews on file (all4shooters, Armory Blog) are of the RB5000"},{"level":"gap","where":"part larue-mbt-2s gap","message":"Where it rests in a lower: the outline is as LaRue's photo has it, its tail taken as level — need The user's own, in the lower, from the side and square on, both pins in frame"},{"level":"gap","where":"part larue-mbt-2s gap","message":"Its side outline from the user's own trigger: theirs is in a corner of its photo and cut by the frame's edge, so LaRue's product photo is still the outline, and its scale is the pin's hole taken as the pin's size — need The trigger lying on its side in the middle of the frame, from 3 ft or more, zoomed, a ruler lying beside it on something as thick as the trigger"},{"level":"gap","where":"part larue-mbt-2s gap","message":"The window through the body, the disconnector and its slot, the adjustment screw, the bow's side grooves — need Nothing more for their places (282e8449a1d8 and 70c0dd8b895c have them): a pass on the model, with the side view above for their sizes"},{"level":"gap","where":"part larue-mbt-2s gap","message":"The hammer, its spring and the two pins — need The hammer from its side with a ruler beside it (b6661e28ee95 is edge on): for the exploded view"},{"level":"gap","where":"part law-tactical-gen-s-folder gap","message":"Where the hinge stands along the bore and where the halves meet, read only from how the part lies folded open: no square side view. — need A side view of the part square on (on a lower with its pins in frame, or alone beside a known length)."},{"level":"gap","where":"part law-tactical-gen-s-folder gap","message":"How far the hinge turns past 180 degrees, if at all, and what stops it: the photos have it at 180, lying flat. — need A photo from above of the adapter alone turned as far as it goes."},{"level":"gap","where":"part law-tactical-gen-s-folder gap","message":"The bolt carrier extension's scale: read so its length behind the shoulder is the 1.3 in it makes up (which its weight in steel bears out), the end that goes into the carrier comes out 0.053 in under the carrier's bore. — need A seller's or the maker's figure for the extension's length or diameter, or a photo of it beside a carrier."},{"level":"gap","where":"part law-tactical-gen-s-folder gap","message":"The receiver half's front face (its index protrusion, the hole over the takedown pin's spring) and the stock half's and receiver half's undersides (a hole in each): seen only in three-quarter. — need A photo of each face square on."},{"level":"gap","where":"part law-tactical-gen-s-folder gap","message":"Which product code a retail GEN-S carries: the maker's page gives 99312 (the Gen 3-M's before it) and 99329 for government and OEM sales; the sellers on file list 99329. — need The maker's dealer list or a box label."},{"level":"gap","where":"part law-tactical-gen3m-folder gap","message":"Where the hinge stands along the bore and where the halves meet, read only from how the part lies folded open: no square side view. — need A side view of the part square on (on a lower with its pins in frame, or alone beside a known length)."},{"level":"gap","where":"part law-tactical-gen3m-folder gap","message":"How far the hinge turns past 180 degrees, if at all, and what stops it: the photos have it at 180, lying flat; the patent says the stock folds flat against the receiver. — need A photo from above of the adapter alone turned as far as it goes."},{"level":"gap","where":"part law-tactical-gen3m-folder gap","message":"The receiver half's front face: its protrusion into the lower's index indentation (the sheet's X), the hole over the takedown pin's spring, and any relief round the flange. No photo of that face square on is on file. — need A photo of the receiver half's front face, square on (Law Tactical's or a seller's)."},{"level":"gap","where":"part law-tactical-gen3m-folder gap","message":"The bolt carrier extension's scale: read so its length behind the shoulder is the 1.3 in it makes up, on two close photos taken from above; the stem's length differs between them by 0.054 in (a conflict in the ledger). — need A seller's or the maker's figure for the extension's length or diameter, or a side photo of it square on."},{"level":"gap","where":"part law-tactical-gen3m-folder gap","message":"Law Tactical's own page for the Gen 3-M now shows the Gen-S; Primary Arms' page for it (URL from the brief) answered 404, Rainier Arms' and AT3's refused the reader (403). — need Nothing: the sellers' pages on file give the figures."},{"level":"gap","where":"part magpul-ctr gap","message":"Its end section and the friction lock housing's width (the MOE Carbine's section stands in) — need a straight end-on or underside photo of the CTR with a known size in frame"},{"level":"gap","where":"part magpul-ctr gap","message":"Its seat on the tube from its own photo (three steps out, it lands inside the castle nut) — need a straight side photo of it collapsed on a lower with both receiver pins in view"},{"level":"gap","where":"part magpul-ctr gap","message":"The pieces that stay black on a coloured stock (the QD socket's steel cup, the lock pin's head, the friction lock's pivot pin) as surfaces of their own — need their sizes read into the ledger (the cup's rim round the traced socket, the pins' heads) from a straight side photo of a coloured CTR"},{"level":"gap","where":"part magpul-mbus-3-front gap","message":"What Magpul's \"1.38 in wide\" spans: 0.08 to 0.12 in more than the sight measures in its patent and its own photographs — need A dimensioned drawing, or a straight end view of the sight on a rail with the rail's width in frame"},{"level":"gap","where":"part magpul-mbus-3-front gap","message":"The sight line's height as a maker's figure (Magpul: \"Standard AR sight height\"); T.REX ARMS' 1.41 in doesn't say what it is measured to — need Magpul's figure for the post's tip over the rail, or a square side photo of it standing on a rail"},{"level":"gap","where":"part magpul-mbus-3-front gap","message":"The standing height, the hinge and the clamp's reach rest on the patent's figures at one published length (a seller's row) — need A square side photo of the sight standing on a rail, the rail's teeth in frame"},{"level":"gap","where":"part magpul-mbus-3-front gap","message":"The weight's split between the polymer body and its steel (bolt, pins, spring, post) — need Nothing published: the centre of mass treats it as one material"},{"level":"gap","where":"part magpul-mbus-3-rear gap","message":"A length from Magpul (its page states none; a seller's 2.43 in is 0.08 in more than the patent's figures and Magpul's photo give) — need Magpul's own stowed length, or a straight side photo of it stowed with a scale in its plane"},{"level":"gap","where":"part magpul-mbus-3-rear gap","message":"What the stowed height is measured to: Magpul's ~0.55 in against 0.52 in to the windage knob's rim on the patent's figures and in Magpul's photo — need A dimensioned drawing, or a straight end view of it stowed on a rail"},{"level":"gap","where":"part magpul-mbus-3-rear gap","message":"The aperture arm's ribs (they run along the bar on the product and across it in the patent), the windage marks on the arm's rear face, the MBUS lettering and the Magpul mark — need Surface detail; not modelled"},{"level":"gap","where":"part magpul-mbus-3-rear gap","message":"What the hardware is made of and its finish — need A statement from Magpul"},{"level":"gap","where":"part magpul-mbus-pro-front gap","message":"The sight's true scale: Magpul's 1.63 in stowed length against 1.57 (Recoil, 2015) and a .835 in rail in the patent's clamp — need A photo of it on a rail straight from the side or from above (the slots give the scale), or a dimensioned drawing"},{"level":"gap","where":"part magpul-mbus-pro-front gap","message":"Its width — need A maker's figure; it is read off the patent's front elevation (1.25 in across the cross bolt)"},{"level":"gap","where":"part magpul-mbus-pro-front gap","message":"The deck under the arm and the clamp's separate bar — need The deck from a straight photo of it standing from the rear or above; the bar from the patent's FIG. 4 and FIG. 5, which are on file and not yet traced"},{"level":"gap","where":"part magpul-mbus-pro-front gap","message":"The colour — need A match to a photo under the app's light; the placeholder black stands in"},{"level":"gap","where":"part magpul-mbus-pro-rear gap","message":"Its width is the patent's, not a published figure (1.397 in over the windage knob and the clamp screw's head) — need A maker's figure, or a straight end view of the sight with a scale in its plane. AR15Discounts' shop field (2.1 × 1.4 × 0.38 in, unlabelled) may be the same width."},{"level":"gap","where":"part magpul-mbus-pro-rear gap","message":"Its standing height (1.63 in) and the arm's lean when it stands come from the patent's folded figures turned up, not from a view of it standing — need Magpul's photos of it standing from the side (a7d9a987a0d9) and from behind (acc7c896d80c) traced: the aperture's published height scales the second."},{"level":"gap","where":"part magpul-mbus-pro-rear gap","message":"No recess's depth is sourced (one figure, 0.03 ± 0.02 in, stands for all) — need A section, or two views of the arm's rear face from known angles."},{"level":"gap","where":"part magpul-mbus-pro-rear gap","message":"The colour is a placeholder black — need Two large photos sampled and matched under the app's light (docs/pipeline/ONBOARDING.md, stage 7); a nitrided steel's look is mostly reflection."},{"level":"gap","where":"part magpul-mbus-pro-rear gap","message":"Which end of the rail it goes on is from its name and its page's \"Position Rear\": the installation sheet says only which way round — need A maker's sentence, or the app's own rule for a rear sight. Folded, the arm needs 1.28 in of rail (or of clear air over the charging handle) behind the base."},{"level":"gap","where":"part magpul-mlok-aluminum-rail-section-3-slot interface mlok.reach_inside","message":"needs magpul-mlok-aluminum-rail-section-3-slot.reach_inside"},{"level":"gap","where":"part magpul-mlok-aluminum-rail-section-3-slot gap","message":"Its height above the hand guard's face, and how wide it is under the head — need A view of this length from its end or its side: its height is the line's, read on the five-slot, and its own oblique photo reads it to ± 0.04 in"},{"level":"gap","where":"part magpul-mlok-aluminum-rail-section-3-slot gap","message":"Its weight — need A page that weighs it, Magpul's or a seller's that isn't a shipping weight: worked out from the model's aluminium meanwhile (weight)"},{"level":"gap","where":"part magpul-mlok-aluminum-rail-section-3-slot gap","message":"How far its recoil lugs stand below the base (Primary Arms' photo of its underside shows where they are) and how far the T-nuts reach inside the hand guard (reach_inside) — need A view of it from its end or its side, or Magpul's drawing of it"},{"level":"gap","where":"part magpul-mlok-aluminum-rail-section-5-slot interface mlok.reach_inside","message":"needs magpul-mlok-aluminum-rail-section-5-slot.reach_inside"},{"level":"gap","where":"part magpul-mlok-aluminum-rail-section-5-slot gap","message":"Its height above the hand guard's face, and how wide it is under the head — need A view of it from its end, or a straight side view, with a scale: the one oblique photo reads 0.24 in with the body as narrow as the standard's lower gauge line, 0.21 if 0.79 across"},{"level":"gap","where":"part magpul-mlok-aluminum-rail-section-5-slot gap","message":"Its weight — need A page that weighs it, Magpul's or a seller's that isn't a shipping weight: worked out from the model's aluminium meanwhile (weight)"},{"level":"gap","where":"part magpul-mlok-aluminum-rail-section-5-slot gap","message":"Its underside: the recoil lugs (how many, their size and where) and how far the T-nuts reach inside the hand guard (reach_inside) — need A view of its underside, or Magpul's drawing of it"},{"level":"gap","where":"part magpul-mlok-aluminum-rail-section-7-slot interface mlok.reach_inside","message":"needs magpul-mlok-aluminum-rail-section-7-slot.reach_inside"},{"level":"gap","where":"part magpul-mlok-aluminum-rail-section-7-slot gap","message":"Its height above the hand guard's face, and how wide it is under the head — need A view of this length from its end or its side, at an angle a camera can be fitted to: its height is the line's, read on the five-slot"},{"level":"gap","where":"part magpul-mlok-aluminum-rail-section-7-slot gap","message":"Its end bevel's run: the line's, as the three- and five-slot's views from above read it — need A view from above lit so that the bevel's top edge shows"},{"level":"gap","where":"part magpul-mlok-aluminum-rail-section-7-slot gap","message":"Its weight — need A page that weighs it, Magpul's or a seller's that isn't a shipping weight: worked out from the model's aluminium meanwhile (weight)"},{"level":"gap","where":"part magpul-mlok-aluminum-rail-section-7-slot gap","message":"Its underside: the recoil lugs (how many, their size and where) and how far the T-nuts reach inside the hand guard (reach_inside) — need A view of its underside, or Magpul's drawing of it"},{"level":"gap","where":"part magpul-mlok-aluminum-rail-section-9-slot interface mlok.reach_inside","message":"needs magpul-mlok-aluminum-rail-section-9-slot.reach_inside"},{"level":"gap","where":"part magpul-mlok-aluminum-rail-section-9-slot gap","message":"Its height above the hand guard's face, and how wide it is under the head — need A view of this length from its end or its side, at an angle a camera can be fitted to: its height is the line's, read on the five-slot"},{"level":"gap","where":"part magpul-mlok-aluminum-rail-section-9-slot gap","message":"Its end bevel's run: the line's, as the three- and five-slot's views from above read it — need A view from above lit so that the bevel's top edge shows"},{"level":"gap","where":"part magpul-mlok-aluminum-rail-section-9-slot gap","message":"Its weight — need A page that weighs it, Magpul's or a seller's that isn't a shipping weight: worked out from the model's aluminium meanwhile (weight)"},{"level":"gap","where":"part magpul-mlok-aluminum-rail-section-9-slot gap","message":"Its underside: the recoil lugs (how many, their size and where) and how far the T-nuts reach inside the hand guard (reach_inside) — need A view of its underside, or Magpul's drawing of it"},{"level":"gap","where":"part magpul-mlok-hand-stop-moe-adapter interface mlok.reach_inside","message":"needs magpul-mlok-hand-stop-moe-adapter.reach_inside"},{"level":"gap","where":"part magpul-mlok-hand-stop-moe-adapter interface carries.reach_inside","message":"needs magpul-mlok-hand-stop-moe-adapter.carried_reach_inside"},{"level":"gap","where":"part magpul-mlok-hand-stop-moe-adapter gap","message":"A size for it from its maker: every figure is read from photographs, the widths from one — need A Magpul drawing or figure for the kit's pieces, a seller's measurement, or a view of it from its end with a scale"},{"level":"gap","where":"part magpul-mlok-hand-stop-moe-adapter gap","message":"How far the moulded cover's ribbed underside stands below the end sections' mounting face, and so whether the plate's ends or its middle meet a flat face first (cover_underside_drop) — need A side view of the plate alone square to its length, or of its mounting side beside a scale"},{"level":"gap","where":"part magpul-mlok-hand-stop-moe-adapter gap","message":"How far the seats round its screw holes stand into the hand guard's slot (reach_inside), and the room under an accessory (carried_reach_inside) — need A section, or a photo of its mounting side from its edge"},{"level":"gap","where":"part magpul-mlok-hand-stop-moe-adapter gap","message":"How deep the snap-off scores are, and how the cover's top rounds into its ends — need A close side view of the plate alone"},{"level":"gap","where":"part magpul-mlok-hand-stop interface mlok.reach_inside","message":"needs magpul-mlok-hand-stop.reach_inside"},{"level":"gap","where":"part magpul-mlok-hand-stop gap","message":"How far the T-nuts reach inside the handguard (reach_inside) — need A Magpul figure for the M-LOK T-nut's height"},{"level":"gap","where":"part magpul-mlok-hand-stop gap","message":"How it sits on the kit's MOE adapter plate (magpul-mlok-hand-stop-moe-adapter, a part since 2026-10-05: D72): by the two parts' figures its band bears on the plate's flat and its ears' tips end 0.013 in past the plate's underside, and its plate runs 0.03 in into the foot of the adapter's moulded cover one way round — need A view of the stop on the plate from its end or its side with a scale: the band's depth here (the patent's outermost line) and the plate's thickness (two photos through fitted cameras) are each good to a hundredth"},{"level":"gap","where":"part magpul-mlok-hand-stop gap","message":"How far its ears stand above the band between them: the patent's outermost line there is 0.116 in, and the image of it installed has its plate 0.04 in thinner than the patent's (the ledger's height) — need A view of it from the plate's end with a scale, or of its mounting side beside the T-nuts"},{"level":"gap","where":"part magpul-mlok-hand-stop gap","message":"The source page of the user's photo — need The gallery it was screenshotted from, for the manifest"},{"level":"gap","where":"part magpul-mlok-index-panel interface mlok.reach_inside","message":"needs magpul-mlok-index-panel.reach_inside"},{"level":"gap","where":"part magpul-mlok-index-panel gap","message":"How far the T-nut reaches inside the handguard (reach_inside) — need A Magpul figure for the M-LOK T-nut's height"},{"level":"gap","where":"part magpul-mlok-index-panel gap","message":"A size for it from its maker (its length, height and width are read from an image and a patent) — need A Magpul drawing or figure for the kit's pieces, or a seller's measurement"},{"level":"gap","where":"part magpul-mlok-index-panel gap","message":"How deep the screw's recess is, and how far the fin's faces are dished — need A section, or a close photo square to the fin's edge"},{"level":"gap","where":"part magpul-mlok-index-panel gap","message":"The source page of the user's photo — need The gallery it was screenshotted from, for the manifest"},{"level":"gap","where":"part magpul-mlok-mvg interface mlok.reach_inside","message":"needs magpul-mlok-mvg.reach_inside"},{"level":"gap","where":"part magpul-mlok-mvg gap","message":"How far the T-nuts reach inside the handguard (reach_inside) — need A Magpul figure or drawing of the M-LOK T-nut's height, or a straight photo of a nut beside its 7 mm flats; the FAQ says the nut's drawings are restricted"},{"level":"gap","where":"part magpul-mlok-polymer-rail-section-11-slot interface mlok.reach_inside","message":"needs magpul-mlok-polymer-rail-section-11-slot.reach_inside"},{"level":"gap","where":"part magpul-mlok-polymer-rail-section-11-slot gap","message":"Magpul's own height, width and weight for it — need A specification table or a drawing from Magpul; a seller's measured figures; or a level side view or end view of it with a scale (its own rail slots in frame)"},{"level":"gap","where":"part magpul-mlok-polymer-rail-section-11-slot gap","message":"Where its T-nuts sit in an M-LOK slot, and how far they and its recoil lugs reach inside (reach_inside) — need Magpul's instruction for the rail sections, or a side view of one fitted to a hand guard with the slots in frame"},{"level":"gap","where":"part magpul-mlok-polymer-rail-section-11-slot gap","message":"The underside's pocket, its rim and its lugs — need A square view of its underside with a scale; drawn flat meanwhile"},{"level":"gap","where":"part magpul-mlok-polymer-rail-section-11-slot gap","message":"Which two of its three holes its two screws go in — need Magpul's word on the \"intermediate spacing option\"; the model has them in the end holes"},{"level":"gap","where":"part magpul-mlok-polymer-rail-section-3-slot interface mlok.reach_inside","message":"needs magpul-mlok-polymer-rail-section-3-slot.reach_inside"},{"level":"gap","where":"part magpul-mlok-polymer-rail-section-3-slot gap","message":"Magpul's own height, width and weight for it — need A specification table or a drawing from Magpul; a seller's measured figures; or a level side view or end view of it with a scale (its own rail slots in frame)"},{"level":"gap","where":"part magpul-mlok-polymer-rail-section-3-slot gap","message":"Where its T-nuts sit in an M-LOK slot, and how far they and its recoil lugs reach inside (reach_inside) — need Magpul's instruction for the rail sections, or a side view of one fitted to a hand guard with the slots in frame"},{"level":"gap","where":"part magpul-mlok-polymer-rail-section-3-slot gap","message":"The underside's pocket, its rim and its lugs — need A square view of its underside with a scale; drawn flat meanwhile"},{"level":"gap","where":"part magpul-mlok-polymer-rail-section-5-slot interface mlok.reach_inside","message":"needs magpul-mlok-polymer-rail-section-5-slot.reach_inside"},{"level":"gap","where":"part magpul-mlok-polymer-rail-section-5-slot gap","message":"Magpul's own height, width and weight for it — need A specification table or a drawing from Magpul; a seller's measured figures; or a level side view or end view of it with a scale (its own rail slots in frame)"},{"level":"gap","where":"part magpul-mlok-polymer-rail-section-5-slot gap","message":"Where its T-nuts sit in an M-LOK slot, and how far they and its recoil lugs reach inside (reach_inside) — need Magpul's instruction for the rail sections, or a side view of one fitted to a hand guard with the slots in frame"},{"level":"gap","where":"part magpul-mlok-polymer-rail-section-5-slot gap","message":"The underside's pocket, its rim and its lugs — need A square view of its underside with a scale; drawn flat meanwhile"},{"level":"gap","where":"part magpul-mlok-polymer-rail-section-7-slot interface mlok.reach_inside","message":"needs magpul-mlok-polymer-rail-section-7-slot.reach_inside"},{"level":"gap","where":"part magpul-mlok-polymer-rail-section-7-slot gap","message":"Magpul's own height, width and weight for it — need A specification table or a drawing from Magpul; a seller's measured figures; or a level side view or end view of it with a scale (its own rail slots in frame)"},{"level":"gap","where":"part magpul-mlok-polymer-rail-section-7-slot gap","message":"Where its T-nuts sit in an M-LOK slot, and how far they and its recoil lugs reach inside (reach_inside) — need Magpul's instruction for the rail sections, or a side view of one fitted to a hand guard with the slots in frame"},{"level":"gap","where":"part magpul-mlok-polymer-rail-section-7-slot gap","message":"The underside's pocket, its rim and its lugs — need A square view of its underside with a scale; drawn flat meanwhile"},{"level":"gap","where":"part magpul-mlok-polymer-rail-section-9-slot interface mlok.reach_inside","message":"needs magpul-mlok-polymer-rail-section-9-slot.reach_inside"},{"level":"gap","where":"part magpul-mlok-polymer-rail-section-9-slot gap","message":"Magpul's own height, width and weight for it — need A specification table or a drawing from Magpul; a seller's measured figures; or a level side view or end view of it with a scale (its own rail slots in frame)"},{"level":"gap","where":"part magpul-mlok-polymer-rail-section-9-slot gap","message":"Where its T-nuts sit in an M-LOK slot, and how far they and its recoil lugs reach inside (reach_inside) — need Magpul's instruction for the rail sections, or a side view of one fitted to a hand guard with the slots in frame"},{"level":"gap","where":"part magpul-mlok-polymer-rail-section-9-slot gap","message":"The underside's pocket, its rim and its lugs — need A square view of its underside with a scale; drawn flat meanwhile"},{"level":"gap","where":"part magpul-mlok-polymer-rail-section-9-slot gap","message":"Which two of its three holes its two screws go in — need Magpul's word on the \"intermediate spacing option\"; the model has them in the end holes"},{"level":"gap","where":"part magpul-mlok-qd-sling-mount interface mlok.reach_inside","message":"needs magpul-mlok-qd-sling-mount.reach_inside"},{"level":"gap","where":"part magpul-mlok-qd-sling-mount gap","message":"How far the T-nuts reach inside the handguard (reach_inside) — need A Magpul figure or drawing of the M-LOK T-nut's height"},{"level":"gap","where":"part magpul-mlok-qd-sling-mount gap","message":"Whether the steel mount sold today has the patent's shape — need A straight photo of the current mount beside a scale, or a drawing: the patent is of the aluminum mount, and the weights suggest the steel one has less metal in it than this shape would. Its plan agrees where Magpul's photos show it (the screws' spacing, the ring's face)"},{"level":"gap","where":"part magpul-mlok-qd-sling-mount gap","message":"The screws' size and what coats them (their heads are drawn from two photo readings, ± 0.015 and ± 0.03 in), and the T-nuts — need A figure for the screw's head (Magpul's sheet gives only its 5/32 in hex) or a straight photo of the mount with its hardware beside a scale"},{"level":"gap","where":"part magpul-mlok-rail-cover-type-2 gap","message":"A published length, width or weight for one cover — need Magpul states none (its page, its information sheet and its instruction sheet were read): the length is read on a picture of a row of covers, the width is the patent's at that length, the weight is a retailer's list of the hand stop kit's pieces (0.15 oz, source unstated)"},{"level":"gap","where":"part magpul-mlok-rail-cover-type-2 gap","message":"Whether a handguard's M-LOK face takes it — need Each host's face width beside its slots and how its corners fall away, to hold against the cover's pad (0.61 in) and its wings (0.11 in below the pad): Magpul says it may not fit a wider, flatter profile and names no figure"},{"level":"gap","where":"part magpul-mlok-rail-cover-type-2 gap","message":"How far it reaches inside the handguard once locked (reach_inside is the patent's broken lines: 0.21 in ± 0.02) — need A straight photo of a cover from its side with the tab home, lugs and legs in view, or a figure from Magpul"},{"level":"gap","where":"part magpul-mlok-rail-cover-type-2 gap","message":"The source page of the user's image — need The gallery it was screenshotted from, for the manifest (the hand stop's gap too)"},{"level":"gap","where":"part magpul-mlok-rail-cover-type-2 gap","message":"The colour Modified Coyote Brown — need A colour preset matched for it (Magpul's page lists it for MAG603; its information sheet doesn't)"},{"level":"gap","where":"part magpul-moe-carbine gap","message":"Its seat on the tube to better than 0.08 in (Magpul's two photos of it on a rifle differ by 0.1) — need a straight side photo of it collapsed on a lower with both receiver pins in view"},{"level":"gap","where":"part magpul-moe-carbine gap","message":"The frame's widths: the upright, the strut, the brace, and the butt's flare — need a rear or underside photo square-on with a known size in frame"},{"level":"gap","where":"part magpul-moe-k2-plus gap","message":"Whether the left side of the top block has a plate as the right has (it is drawn bare), and the plate's place below the top on a view square to it (the two photos read differ by 0.03 in) — need The grip's left side and its right side, each square on from 8 ft or more, zoomed, with a tape lying on the grip"},{"level":"gap","where":"part magpul-moe-k2-plus gap","message":"How deep the relief under the top block stands in along its length (its lines are the patent's; its depth is from two outlines, and toward the nose assumed), and how the logo plate and the latch's opening are sunk (assumed: 0.02 and 0.05 in) — need The grip from below its base looking up along the strap, and from the front looking straight back along the rifle, each from 8 ft or more, zoomed: the outlines the relief makes"},{"level":"gap","where":"part magpul-moe-k2-plus gap","message":"The relief's lower edge where it climbs the nose, and the nose's cheeks (drawn as the hull of three outlines; the patent has the block's front edge as a band up the nose) — need The grip from the front quarter, right and left, from 8 ft or more, zoomed"},{"level":"gap","where":"part magpul-moe-k2-plus gap","message":"The beavertail's tip, whose edges are broken by thousandths where the grip's are round, and how its rear face rounds across (0.11 in by the patent's MOE-K2) — need The grip from behind, square to its back strap, from 8 ft or more, zoomed, with a tape lying on it"},{"level":"gap","where":"part magpul-moe-k2-plus gap","message":"The cap under the base (its outline, the MOE lettering) and the top face under the receiver (the screw's hole, the detent spring's hole, the step round the slot) — need Nothing more for the top: the user's photos of it are on file (9455489fc6df, 906083dafd0e, 45eafc02ec88) and it is hidden once installed. For the cap: the base straight on from below with a tape lying on it"},{"level":"gap","where":"part magpul-moe-mlok-handguard-carbine interface mlok.reach_inside","message":"needs magpul-moe-mlok-handguard-carbine.reach_inside"},{"level":"gap","where":"part magpul-moe-mlok-handguard-carbine interface mlok_bottom.reach_inside","message":"needs magpul-moe-mlok-handguard-carbine.reach_inside"},{"level":"gap","where":"part magpul-moe-mlok-handguard-carbine checklist","message":"handguard checklist: \"inside_diameter\" still missing"},{"level":"gap","where":"part magpul-moe-mlok-handguard-carbine gap","message":"Its underside: the six o'clock M-LOK row's count and places, and where the heat shield's rivets are — need A photo of a MOE M-LOK carbine-length from below, its whole underside in frame (a seller's gallery or a review)"},{"level":"gap","where":"part magpul-moe-mlok-handguard-carbine gap","message":"Its section square on (how wide the crown and the underside are, how the faces lean) and its width — need An end view with a known size in frame, or a photo from above; Magpul publishes no drawing"},{"level":"gap","where":"part magpul-moe-mlok-handguard-carbine gap","message":"Its wall and what is inside it (ribs, bosses, the flanges' sizes) — need A photo into either end, or of a half alone from inside"},{"level":"gap","where":"part magpul-moe-mlok-handguard-carbine gap","message":"Magpul's height, 2.5 in excluding the lip, against the photo's 2.38 — need What Magpul measured over; a seller's or a reviewer's own measurement"},{"level":"gap","where":"part magpul-moe-mlok-handguard-mid interface mlok.reach_inside","message":"needs magpul-moe-mlok-handguard-mid.reach_inside"},{"level":"gap","where":"part magpul-moe-mlok-handguard-mid interface mlok_bottom.reach_inside","message":"needs magpul-moe-mlok-handguard-mid.reach_inside"},{"level":"gap","where":"part magpul-moe-mlok-handguard-mid checklist","message":"handguard checklist: \"inside_diameter\" still missing"},{"level":"gap","where":"part magpul-moe-mlok-handguard-mid gap","message":"Its underside: the six o'clock M-LOK row's count and places, and the heat shield's rivets — need A photo of a MOE M-LOK mid-length from below, its whole underside in frame (a seller's gallery or a review)"},{"level":"gap","where":"part magpul-moe-mlok-handguard-mid gap","message":"Its section square on (how wide the crown and the underside are, how the faces lean) and its width — need An end view with a known size in frame, or a photo from above; Magpul publishes no drawing"},{"level":"gap","where":"part magpul-moe-mlok-handguard-mid gap","message":"Its wall and what is inside it (ribs, bosses, the flanges' sizes) — need A photo into either end, or of a half alone from inside"},{"level":"gap","where":"part magpul-moe-mlok-handguard-mid gap","message":"Magpul's height, 2.5 in excluding the lip, against the photos' 2.34 to 2.38 — need What Magpul measured over; a seller's or a reviewer's own measurement"},{"level":"gap","where":"part magpul-moe-plus gap","message":"Its lug slot's width measured on an MOE+ (it is drawn at the MOE-K2+'s) — need a view of an MOE+'s top from above with a scale, or the slot against the top's width in one"},{"level":"gap","where":"part magpul-moe-plus gap","message":"Its seat, lean and drop measured on the MOE+ itself (they are the plain MOE's) — need a straight side photo of an MOE+ on a lower with the receiver's pins in view"},{"level":"gap","where":"part magpul-moe-plus gap","message":"The black rim's own line round the foot (lower at the corners, rising mid-side where the cap latches) and the logo plate as their own surfaces — need a straight side photo of a coloured MOE+ at a known scale: the base is cut square across at the top of the lip meanwhile"},{"level":"gap","where":"part magpul-moe-sl-carbine gap","message":"The step along the pocket 0.37 in under the cheek's edge: on the side photo a lit band with a shadow 0.14 in high under it, the length of the pocket. Not drawn: the pocket's wall is one plane from the cheek's edge down. — need A close view from the front quarter or from below that shows which side of the step stands proud, and by how much."},{"level":"gap","where":"part magpul-moe-sl-carbine gap","message":"How deep the floors inside the frame lie (drawn 0.05 in, from a shadow and from the patent's front view), whether the three are one depth, and how far the QD socket's ring stands from the frame (drawn at the frame's face). — need A view along a floor's edge, or a section; the ring from below or from the front quarter, close."},{"level":"gap","where":"part magpul-moe-sl-carbine gap","message":"The grip's ridges in section, and whether the band over them on the side photo (0.04 in high) is an upright edge, as drawn, or the grip's upper face seen from a little above. The patent draws an upright end 0.1 in high. — need A close view of the grip from its end or from below."},{"level":"gap","where":"part magpul-moe-sl-carbine gap","message":"The latch's hook round the lock pin, the housing the pin's slot is in (the patent's bottom plan draws the stock 0.72 in from the middle each side between 4.4 and 5.2 in ahead of the butt, which nothing on the side photo was matched to), the pivot's black pin in its boss (seen on the left side only) and the small screw in the frame under the lock pin (0.08 in across). — need A close view of the slot and the boss from each side; the screw and the pivot pin are on the photos on file and wait for a slot for black steel."},{"level":"gap","where":"part magpul-moe-sl-handguard-carbine interface mlok.reach_inside","message":"needs magpul-moe-sl-handguard-carbine.reach_inside"},{"level":"gap","where":"part magpul-moe-sl-handguard-carbine interface mlok_bottom.reach_inside","message":"needs magpul-moe-sl-handguard-carbine.reach_inside"},{"level":"gap","where":"part magpul-moe-sl-handguard-carbine checklist","message":"handguard checklist: \"inside_diameter\" still missing"},{"level":"gap","where":"part magpul-moe-sl-handguard-carbine gap","message":"Its section square on (how the crown, the faces and the underside are shaped) and its wall — need An end view with a known size in frame, or a half alone from inside; Magpul publishes no drawing"},{"level":"gap","where":"part magpul-moe-sl-handguard-carbine gap","message":"Where its tongues and window sit against a delta ring placed by the standard: the photos have the ring's front end at the window's front edge, which places the hand guard here; the standard puts the ring itself 0.2 to 0.4 in further back than Magpul's rifle shows it against its receiver — need A photo of a MOE SL on a rifle whose receiver, delta ring and hand guard are all in frame from the side, close"},{"level":"gap","where":"part magpul-moe-sl-handguard-carbine gap","message":"Its front flange and what is inside the side extensions — need A photo into its front end, or of the upper half alone"},{"level":"gap","where":"part magpul-moe-sl-handguard-carbine gap","message":"Magpul's height, 2.4 in, against the photos' 2.32 — need What Magpul measured over; a seller's or a reviewer's own measurement"},{"level":"gap","where":"part magpul-moe-sl-handguard-mid interface mlok.reach_inside","message":"needs magpul-moe-sl-handguard-mid.reach_inside"},{"level":"gap","where":"part magpul-moe-sl-handguard-mid interface mlok_bottom.reach_inside","message":"needs magpul-moe-sl-handguard-mid.reach_inside"},{"level":"gap","where":"part magpul-moe-sl-handguard-mid checklist","message":"handguard checklist: \"inside_diameter\" still missing"},{"level":"gap","where":"part magpul-moe-sl-handguard-mid gap","message":"Its underside: the six o'clock M-LOK row's count and places, and the heat shield's rivets — need A photo of a MOE SL mid-length from below, its whole underside in frame (Magpul's carbine has one, d4a119f9380f)"},{"level":"gap","where":"part magpul-moe-sl-handguard-mid gap","message":"Its section square on (how the crown, the faces and the underside are shaped) and its wall — need An end view with a known size in frame, or a half alone from inside; Magpul publishes no drawing"},{"level":"gap","where":"part magpul-moe-sl-handguard-mid gap","message":"Where its tongues and window sit against a delta ring placed by the standard: the photos have the ring's front end at the window's front edge, which places the hand guard here; the standard puts the ring itself 0.3 to 0.4 in further back than Magpul's rifle shows it against its receiver — need A photo of a MOE SL on a rifle whose receiver, delta ring and hand guard are all in frame from the side, close"},{"level":"gap","where":"part magpul-moe-sl-handguard-mid gap","message":"Its front flange and what is inside the side extensions — need A photo into its front end, or of the upper half alone"},{"level":"gap","where":"part magpul-moe-sl-handguard-mid gap","message":"Magpul's height, 2.4 in, against the photos' 2.32 — need What Magpul measured over; a seller's or a reviewer's own measurement"},{"level":"gap","where":"part magpul-pmag-20-gen-m3 checklist","message":"magazine checklist: \"body_height\" still missing"},{"level":"gap","where":"part magpul-pmag-20-gen-m3 checklist","message":"magazine checklist: \"feed_lip_block_height\" still missing"},{"level":"gap","where":"part magpul-pmag-20-gen-m3 gap","message":"What stands under the catch notch on this magazine (not drawn): its patent's two elevations have a block there 0.057 in out of a side that is as wide as the well already, and Magpul's photo shows its outline — need A view of MAG560 from its front or its rear with the left side in profile at the catch notch, or Magpul's own figure (the same question as the 30-round's)"},{"level":"gap","where":"part magpul-pmag-20-gen-m3 gap","message":"How deep the dot matrix's squares are (drawn 0.016 in, six tenths of the panels' depth), and their size on this magazine itself (the 30-round's photo reading is used; this one's patent draws them larger) — need A close view of this magazine's dot matrix, square on with something of known size beside it, and an oblique one lit from one side"},{"level":"gap","where":"part magpul-pmag-20-gen-m3 gap","message":"The body's width: the patent's elevations scaled by the height give 0.902 in, one seller's table 0.87 in, and Magpul none — need Magpul's own figure, or a view from the top or the bottom with something of known size in its plane"},{"level":"gap","where":"part magpul-pmag-20-gen-m3 gap","message":"What Magpul's 'Length, max' runs between isn't said on its page (taken as the upright height: the top section then matches the 30-round's and the photo); a seller's table has 5.7 in — need Magpul's own drawing, or an owner's ruler along it"},{"level":"gap","where":"part magpul-pmag-20-gen-m3 gap","message":"The feed lips, the bolt catch's relief at the rear of the top, the follower and the floorplate from below are the hull's or not drawn — need Tracing the patent's top and bottom plans (FIGS. 4 and 5, on file) and its rear elevation's top: not done in this pass"},{"level":"gap","where":"part magpul-pmag-20-gen-m3 gap","message":"The over-travel stop's underside in section (ruled faces between the edges the patent draws), and the step Magpul's photograph has in the floorplate's edge near the front (this patent's edge is straight) — need A view of MAG560 from below its spine; the left elevation traced again from Magpul's photograph for the edge"},{"level":"gap","where":"part magpul-pmag-20-gen-m3 gap","message":"The ODG one's number rests on one seller's page (Shiner Tactical: 'Manufacturer Part Number MAG560-ODG'); Magpul's page states none in words — need A second seller's page for the green one (Midwest Gun Works' /prod/MAG560-ODG answered 404 on 2026-10-13), or Magpul's"},{"level":"gap","where":"part magpul-pmag-30-gen-m3 checklist","message":"magazine checklist: \"body_height\" still missing"},{"level":"gap","where":"part magpul-pmag-30-gen-m3 checklist","message":"magazine checklist: \"feed_lip_block_height\" still missing"},{"level":"gap","where":"part magpul-pmag-30-gen-m3 checklist","message":"magazine checklist: \"hang_below_magwell\" still missing"},{"level":"gap","where":"part magpul-pmag-30-gen-m3 gap","message":"What stands under the catch notch on this magazine (not drawn): the patent's two elevations have a block there 0.054 in out of a side that is as wide as the well already, and Magpul's photo shows its outline — need A view of MAG557 from its front or its rear with the left side in profile at the catch notch, or Magpul's own figure"},{"level":"gap","where":"part magpul-pmag-30-gen-m3 gap","message":"The side panels' depth on this magazine itself — need The same view lower down: it is the window model's drawing that shows the panels' floors in profile, and this magazine's photos show them only obliquely"},{"level":"gap","where":"part magpul-pmag-30-gen-m3 gap","message":"How deep the dot matrix's dimples and the groove near the spine are (drawn 0.015 and 0.025 in: assumed) — need A view along the side from close by with either in profile, or Magpul's own figure"},{"level":"gap","where":"part magpul-pmag-30-gen-m3 gap","message":"The grip frame's corners in section (drawn as quarter ellipses between the patent's lines), where the upper body's lean begins on this magazine (the patent's 0.6 in behind the front: neither side photo has a line there), and how wide the front strip and the spine are on it (the patent's window model's) — need MAG557 from straight above and below, or from its front and its rear, square on"},{"level":"gap","where":"part magpul-pmag-30-gen-m3 gap","message":"Where the spine's second row has its five bars, and the one behind the stop's gusset (drawn at the other rows' spacing: no side view shows them) — need A view of MAG557's spine, square on"},{"level":"gap","where":"part magpul-pmag-30-gen-m3 gap","message":"The over-travel stop's underside in section (its outer parts' ruled faces and the hollows' flat roof are the simplest surfaces between the edges the patent draws), and the stop on this magazine rather than the window model's drawing — need A view of MAG557 from below its spine, or from the rear with the stop's underside lit"},{"level":"gap","where":"part magpul-pmag-30-gen-m3 gap","message":"The floorplate's section along its sides (the front elevation's at its front end, carried along the joint) and the body's tongue ahead of the joint's step — need A view of MAG557 from the front or the rear, square on, low enough to see the floorplate's side in profile"},{"level":"gap","where":"part magpul-pmag-d-60 checklist","message":"magazine checklist: \"body_height\" still missing"},{"level":"gap","where":"part magpul-pmag-d-60 checklist","message":"magazine checklist: \"feed_lip_block_height\" still missing"},{"level":"gap","where":"part magpul-pmag-d-60 checklist","message":"magazine checklist: \"hang_below_magwell\" still missing"},{"level":"gap","where":"part magpul-pmag-d-60 gap","message":"A straight side view of the product: the feed tower's own outline, where it stands on the drum and how far it leans (10 degrees by the patent's broken lines; 10 to 15 by eye on two photos of it in a rifle) — need A studio photo of the D-60 from its side, square on, or a photo of it seated in a lower with both receiver pins in frame (trace.py register)"},{"level":"gap","where":"part magpul-pmag-d-60 gap","message":"How deep the reliefs are (the window's recess, the hub, the dot matrix, the front cover's circles, the seams) and which way the front cover's circles step — need A view of each cover edge on, or close obliques of both covers"},{"level":"gap","where":"part magpul-pmag-d-60 gap","message":"The retaining clips' own shape, the roof round the tower's foot in plan and the lever's thickness — need The patent's top and bottom plans (FIG. 6, 7) traced with the drum's outline (on file; used so far for the drum's depth and its taper), and a close view of the front cover from the side"},{"level":"gap","where":"part magpul-pmag-d-60 gap","message":"The dust cover's weight (Magpul's 20.5 oz is with it) and the magazine's weight without it — need A page or a scale reading that gives either"},{"level":"gap","where":"part magpul-pmag-d-60 gap","message":"The catch notch's height under the lips, to better than the ledge's reading (1.10 in here, 1.07 on the 30-round GEN M3: one catch, one bolt) — need A straight view of the tower's left side"},{"level":"gap","where":"part mas-defense-nero-12-62-handguard interface mlok.reach_inside","message":"needs mas-defense-nero-12-62-handguard.reach_inside"},{"level":"gap","where":"part mas-defense-nero-12-62-handguard gap","message":"A level side picture of this length (its places along it are read through a picture taken from the front right and above) — need MAS's picture of this length on an upper seen from the side, or a seller's"},{"level":"gap","where":"part mas-defense-nero-12-62-handguard gap","message":"Its length: the title says 12.62 in, its pictures 12.84 — need A published overall length with its ends named, or a level side picture"},{"level":"gap","where":"part mas-defense-nero-12-62-handguard gap","message":"The left side's and the bottom's rows of M-LOK slots — need A picture from below or from the left"},{"level":"gap","where":"part mas-defense-nero-12-62-handguard gap","message":"Its section from the end, and the walls inside — need A picture down its length or of its end face"},{"level":"gap","where":"part mas-defense-nero-12-62-handguard gap","message":"The room inside its faces before what runs under it (reach_inside) — need The barrel's and the gas block's sizes under the slots: the build's"},{"level":"gap","where":"part mas-defense-nero-12-62-handguard gap","message":"Which barrel-nut thread its steel nut takes — need A MAS sentence naming the thread"},{"level":"gap","where":"part mas-defense-nero-15-handguard interface mlok.reach_inside","message":"needs mas-defense-nero-15-handguard.reach_inside"},{"level":"gap","where":"part mas-defense-nero-15-handguard gap","message":"Its section from the end: the lower faces' angle, the bottom flat's width, the walls inside — need A picture down its length or of its end face (none on file: MAS's pictures are from above and from the sides)"},{"level":"gap","where":"part mas-defense-nero-15-handguard gap","message":"The bottom's row of M-LOK slots: how many and where — need A picture from below (MAS says only \"3, 6 and 9 o'clock\")"},{"level":"gap","where":"part mas-defense-nero-15-handguard gap","message":"The room inside its faces before what runs under it (reach_inside: what an M-LOK accessory's nuts may take) — need The barrel's and the gas block's sizes under the slots: the build's, once those parts state them"},{"level":"gap","where":"part mas-defense-nero-15-handguard gap","message":"Which barrel-nut thread its steel nut takes — need A MAS sentence naming the thread (its pages say only that the nut \"will only fit our Nero handguards\")"},{"level":"gap","where":"part mas-defense-nero-15-handguard gap","message":"Its barrel nut's own shape (drawn as nothing: it is inside the rear end) — need MAS's NERO barrel nut page's picture at a size to read (MAS00106018: 300 px)"},{"level":"gap","where":"part mas-defense-nero-9-87-handguard interface mlok.reach_inside","message":"needs mas-defense-nero-9-87-handguard.reach_inside"},{"level":"gap","where":"part mas-defense-nero-9-87-handguard gap","message":"A level side picture of this length (its places along it are read through a picture taken from the front right and above) — need MAS's picture of this length on an upper seen from the side, or a seller's"},{"level":"gap","where":"part mas-defense-nero-9-87-handguard gap","message":"Its length: the title says 9.87 in, its pictures 10.01 — need A published overall length with its ends named, or a level side picture"},{"level":"gap","where":"part mas-defense-nero-9-87-handguard gap","message":"The left side's and the bottom's rows of M-LOK slots — need A picture from below or from the left"},{"level":"gap","where":"part mas-defense-nero-9-87-handguard gap","message":"Its section from the end, and the walls inside — need A picture down its length or of its end face"},{"level":"gap","where":"part mas-defense-nero-9-87-handguard gap","message":"The room inside its faces before what runs under it (reach_inside) — need The barrel's and the gas block's sizes under the slots: the build's"},{"level":"gap","where":"part mas-defense-nero-9-87-handguard gap","message":"Which barrel-nut thread its steel nut takes — need A MAS sentence naming the thread"},{"level":"gap","where":"part mft-battlelink-minimalist-stock gap","message":"Where the published 1.752 in width lies: the housing's mouth is 1.61 across, its rear part reads 1.69 ± 0.05 where it begins, and no view shows the butt or the top square (the rear part and the pad round it are drawn at the published width) — need a straight view of the butt or from above, or the maker's drawing"},{"level":"gap","where":"part mft-battlelink-minimalist-stock gap","message":"Its seat on the tube from a square photo (it is seated by its lock pin in the tube's front hole, ± 0.08 in; a seller's oblique of it on a rifle agrees, one hole out) — need a straight side photo of it on a lower with both receiver pins in view, at any position; or a published length of pull"},{"level":"gap","where":"part mft-battlelink-minimalist-stock gap","message":"The housing's section behind its mouth (its rear part is fuller under the ridge, with a ledge of four cells), and how deep each of the frame's panels and the cells is recessed (one reading, 0.25 in of web at one slot, stands for all) — need views from above and below, or an oblique with the camera fitted to it"},{"level":"gap","where":"part mft-battlelink-minimalist-stock gap","message":"The butt pad's face from the rear (its outline, its taper to the toe, the ridges' ends) — need a straight view of the butt"},{"level":"gap","where":"part mft-battlelink-minimalist-stock gap","message":"What the pins, the spring and the QD socket's cup are made of and finished in, and how deep the socket is — need the maker's or a seller's words; a view into the socket"},{"level":"gap","where":"part mft-battlelink-minimalist-stock gap","message":"A patent or drawing of it: the maker's virtual patent marking page (read 2026-10-13) lists one patent, for holsters; its 2013 release says 'patent pending' — need a patent number tied to the stock by the maker"},{"level":"gap","where":"part midwest-combat-rail-15-handguard interface mlok.reach_inside","message":"needs midwest-combat-rail-15-handguard.reach_inside"},{"level":"gap","where":"part midwest-combat-rail-15-handguard interface mlok_between.reach_inside","message":"needs midwest-combat-rail-15-handguard.reach_inside"},{"level":"gap","where":"part midwest-combat-rail-15-handguard gap","message":"Where it stops on the receiver (rear_face_x: drawn against the front shoulder with no gap) — need A photo of this handguard mounted on a forged upper with the receiver's pins in frame; the maker's sheet says only that it slides onto its barrel nut"},{"level":"gap","where":"part midwest-combat-rail-15-handguard gap","message":"Its section square on (the faces' angle, the neck's walls, the channel under the rail, the walls' thickness) — need An end view with a known size in frame, or the maker's drawing: none is published"},{"level":"gap","where":"part midwest-combat-rail-15-handguard gap","message":"Its weight without its barrel nut, torque plate and screws (weight_handguard is worked out from sizes read off photos) — need A page that weighs the handguard alone, or the nut alone"},{"level":"gap","where":"part midwest-combat-rail-15-handguard gap","message":"The room inside its faces before the barrel (reach_inside: what an M-LOK accessory's nuts may take) — need The barrel's and the gas block's size under it, from the parts a build puts there"},{"level":"gap","where":"part midwest-combat-rail-15-handguard gap","message":"What its short cuts behind the side faces' and the underside's slots are for, and whether they take an M-LOK nut — need The maker's word"},{"level":"gap","where":"part midwest-industries-drop-in-mlok-carbine interface mlok.reach_inside","message":"needs midwest-industries-drop-in-mlok-carbine.reach_inside"},{"level":"gap","where":"part midwest-industries-drop-in-mlok-carbine checklist","message":"handguard checklist: \"inside_diameter\" still missing"},{"level":"gap","where":"part midwest-industries-drop-in-mlok-carbine gap","message":"How deep its rail's neck runs before the upper half's top (a shelf 0.41 in under the rail's top as read, on one oblique photo, the engraved face under the head taken for the neck's side as on the maker's Combat Rail; read as a shoulder sloping out from the head instead, 17 of the clamps on file stood in it); Aimpoint's PRO stands on that shelf beside the neck as drawn (app/tests/rail-clamps.test.ts), and every other clamp on file clears it — need A view along it from either end, or a photo of a clamp on its rail from the side"},{"level":"gap","where":"part midwest-industries-drop-in-mlok-carbine gap","message":"A level view of either side, the underside (the fifth QD socket, any slots or holes there) and the left side — need A seller's or a buyer's photos of an MI-17M from the side, from below and from the left: every place on file is read through one oblique photo"},{"level":"gap","where":"part midwest-industries-drop-in-mlok-carbine gap","message":"Its section square on, its wall and the upper half's width — need An end view with a known size in frame (a photo into either end)"},{"level":"gap","where":"part midwest-industries-drop-in-mlok-carbine gap","message":"What bears in the cap at its front, and how far its front reaches over the front sight base — need A photo of it installed on an A2 front sight base, from the side"},{"level":"gap","where":"part midwest-industries-drop-in-mlok-carbine gap","message":"Where the round cap sits inside its front end (the cap's place on a carbine barrel against its photo's front) — need A photo of it installed on a carbine-length rifle with an A2 front sight base"},{"level":"gap","where":"part midwest-industries-drop-in-mlok-mid interface mlok.reach_inside","message":"needs midwest-industries-drop-in-mlok-mid.reach_inside"},{"level":"gap","where":"part midwest-industries-drop-in-mlok-mid checklist","message":"handguard checklist: \"inside_diameter\" still missing"},{"level":"gap","where":"part midwest-industries-drop-in-mlok-mid gap","message":"How deep its rail's neck runs before the upper half's top (a shelf 0.43 in under the rail's top as read, on one oblique photo, the engraved face under the head taken for the neck's side as on the maker's Combat Rail; read as a shoulder sloping out from the head instead, 17 of the clamps on file stood in it); Aimpoint's PRO stands on that shelf beside the neck as drawn (app/tests/rail-clamps.test.ts), and every other clamp on file clears it — need A view along it from either end, or a photo of a clamp on its rail from the side"},{"level":"gap","where":"part midwest-industries-drop-in-mlok-mid gap","message":"A level view of either side, the underside (the fifth QD socket, any slots or holes there) and the left side — need A seller's or a buyer's photos of an MI-18M from the side, from below and from the left: every place on file is read through one oblique photo"},{"level":"gap","where":"part midwest-industries-drop-in-mlok-mid gap","message":"Its section square on, its wall and the upper half's width — need An end view with a known size in frame (a photo into either end)"},{"level":"gap","where":"part midwest-industries-drop-in-mlok-mid gap","message":"What bears in the cap at its front, and how far its front reaches over the front sight base — need A photo of it installed on an A2 front sight base, from the side"},{"level":"gap","where":"part midwest-industries-drop-in-mlok-mid gap","message":"The maker's 8.5 in overall length against its photo's 9.04 for the rail's whole length (the upper half's body alone reads 8.45) — need The maker's word on what the figure spans, or a seller's own measurement"},{"level":"gap","where":"part midwest-mk2-qd-t2-226 gap","message":"The dot the maker's 2.26 in is given for — need A page of Midwest's that says it: the T-2 is taken, the dot the mount is named for; Police1's 2.26 in for \"an Aimpoint T1 style optic\" was of the older mount"},{"level":"gap","where":"part midwest-mk2-qd-t2-226 gap","message":"A straight side view of this height — need The maker's or a seller's: its deck, base and lever are drawn as the 1/3's, its web's length read on a quarter view (± 0.08 in)"},{"level":"gap","where":"part midwest-mk2-qd-t2-226 gap","message":"A weight for the MK2 at this height — need A page that gives it: its metal as modelled stands for it"},{"level":"gap","where":"part midwest-mk2-qd-t2-226 gap","message":"The MK2 T2 Aimpoint Mount (cross bolts) at this height — need Sold by the maker as a product of its own (MI-MK2-T2NV-2.26; Primary Arms the same): two Torx cross bolts where this has the QD lever. Not in this batch. Its torque: the maker's older sheet (MI-T1-NV) and Primary Arms (\"Midwest specifies 40 inch-pounds on the cross bolts\") say 40 in-lb, its own casting in the maker's photo 35 in-lb (4e0436e89122): a note, nothing here reads it"},{"level":"gap","where":"part midwest-mk2-qd-t2-low gap","message":"The maker's height for this mount, in inches, and the dot it is given for — need A page or a drawing of Midwest's: it is read here on a quarter view against the 1/3's, ± 0.06 in"},{"level":"gap","where":"part midwest-mk2-qd-t2-low gap","message":"A straight side view of this height — need The maker's or a seller's: its deck, base and lever are drawn as the 1/3's"},{"level":"gap","where":"part midwest-mk2-qd-t2-low gap","message":"A weight for the MK2 Low — need A page that gives it: its metal as modelled stands for it (Primary Arms' 1.7 oz is the older QD Low's, MI-QDT1-L)"},{"level":"gap","where":"part midwest-mk2-qd-t2-low gap","message":"The MK2 T2 Aimpoint Mount (cross bolts) at this height — need Sold by the maker as a product of its own (MI-MK2-T2L; Primary Arms the same): two Torx cross bolts where this has the QD lever. Not in this batch. Its torque: the maker's older sheet (MI-T1-NV) and Primary Arms (\"Midwest specifies 40 inch-pounds on the cross bolts\") say 40 in-lb, its own casting in the maker's photo 35 in-lb (4e0436e89122): a note, nothing here reads it"},{"level":"gap","where":"part midwest-mk2-qd-t2-lower-13 gap","message":"The maker's height for this mount, in inches, and the dot it is given for — need A page or a drawing of Midwest's with the 1/3 height's figure (an axis over the rail for a named dot, or the deck's own height): it is read here on the maker's photograph of it with a T-2 on it, ± 0.06 in"},{"level":"gap","where":"part midwest-mk2-qd-t2-lower-13 gap","message":"A view of this mount from an end, from above or from below — need The maker's or a seller's straight photograph across the mount: the deck's width, the base's sides, the web's width and the lever's thickness are read on the cross-bolt MK2's view from below or assumed"},{"level":"gap","where":"part midwest-mk2-qd-t2-lower-13 gap","message":"The maker's weight for the MK2 — need A page of Midwest's with it: the one figure on file is Bud's Gun Shop's 3.6 ounces, a seller's"},{"level":"gap","where":"part midwest-mk2-qd-t2-lower-13 gap","message":"The MK2 T2 Aimpoint Mount (cross bolts) at this height — need Sold by the maker as a product of its own (MI-MK2-T21/3; Primary Arms MI-MK2-T21-3): two Torx cross bolts in steel clamps where this has the QD lever. Not in this batch. Its torque: the maker's older sheet (MI-T1-NV) and Primary Arms (\"Midwest specifies 40 inch-pounds on the cross bolts\") say 40 in-lb, its own casting in the maker's photo 35 in-lb (4e0436e89122): a note, nothing here reads it"},{"level":"gap","where":"part nordic-22rb-upper gap","message":"The muzzle's crown: the user's face-on photo (2cd733a9d284) has a ring 0.36 in across round the bore, a recess whose depth no view on file gives; the face is drawn flat, and the bore as one plain hole (its lands and grooves aren't told apart) — need The bare muzzle from a quarter ahead (45 degrees off the bore's line), close, the protector off: the recess's far wall then shows beside its near one"},{"level":"gap","where":"part nordic-22rb-upper gap","message":"The muzzle thread's form and hand: it is a helix, a plain V between the Army drawing's roots and crests without the flats of its form, right-hand by its designation alone (the bare photo's lit flank changes side across the barrel, and the lines' lean isn't read); how long its run-out and its start are; the small break on the shoulder's rim and the face's rim isn't drawn — need The bare muzzle from the side, closer than c0e654135597 and lit from the camera's side: the lines' lean, the last turn into the relief, the rims' breaks"},{"level":"gap","where":"part nordic-22rb-upper gap","message":"The receiver's lower corners ahead of its rear chamfers, on the user's own upper: the 0.134 in drawn is from Nordic's photo down a receiver from its rear, where the user's is chamfered 0.23 (receiver_rear_chamfer_w) — need The underside from 8 ft or more, zoomed, with the light raking across it: the corner's width from 3 in ahead of the takedown pin to the handguard"},{"level":"gap","where":"part nordic-22rb-upper gap","message":"How far the bolt's flat face stands behind the ejection port's opening: the model stands the flat on the bore's round where the photos have its lower edge. The photos of 2026-10-05 from above the rail and from above and to the right have it close under the opening's upper lip, but each is one steep view from close and no two fix a camera — need The port from 8 ft or more, zoomed, twice: once from the front right quarter and once from above the rail looking down into it, the rail's teeth in both frames"},{"level":"gap","where":"part nordic-22rb-upper gap","message":"How deep the bolt's details go: the break along its face's upper edge and down its ends (drawn at 45 degrees), the screw's seat (half the break), the slot the extractor lies in (half the round), the extractor's bar (two thirds of the slot high) and its spring's wire (a third of the pitch). Their places and sizes across the face are read on the square photo of the port (26b2fef5a5a3) and drawn since 2026-10-12; the band under the face is still the round it was taken for — need The same two photos as the face's depth: the port from 8 ft or more, zoomed, from the front right quarter and from above the rail"},{"level":"gap","where":"part nordic-22rb-upper gap","message":"What of the charging handle's latch is under the T and the plate (drawn filling the slot), and how deep the receiver is cut for the latch's arm and for its tooth (cut to the latch and a clearance) — need The handle out of the upper from below, and the receiver's rear from above and from its left with the handle out: the room it leaves"},{"level":"gap","where":"part nordic-22rb-upper gap","message":"How deep the handguard's clamp and panels go: the counterbores the two screw heads sit in and how far under the face the heads stand, the sockets, how far in the threaded holes on the left are open, and whether the blind panels are milled in and how deep (all assumed since 2026-10-13); the blends where the block's ramps meet its flat and the handguard's underside are drawn as plain edges, and what is seen through the slit (black in every photo) isn't known — need The handguard's rear end from below and to each side (45 degrees off straight down), close, with the light raking across the block: each counterbore's far wall beside its near one, and the left face's holes looked into; and one blind panel from along its face, the light across it"},{"level":"gap","where":"part nordic-22rb-upper gap","message":"The bolt assembly's steel rear end behind the receiver's rear face: a disc with a tab up to the T and a pin in the tab, 0.15 in thick, and two bars either side of the handle's shaft. Not drawn: it stands in a lower's buffer tower — need Nothing more: four of the photos of 2026-10-05 have it (953843d0ce18, fc6a01b62b5a, bab1880de544, 0dfba70ae389). For the exploded view"},{"level":"gap","where":"part nordic-thread-protector gap","message":"The flats along its outside: how many, how wide, and where they stop — need The protector off the barrel, stood on end and photographed straight down (the user owns it: it is on their 22RB), and once from the side lying down"},{"level":"gap","where":"part nordic-thread-protector gap","message":"Its own thread and the chamfer at its mouth: the thread drawn is the barrel's, a gap outward — need The same view from above, close: the mouth's chamfer and the thread's crests show as rings"},{"level":"gap","where":"part olight-baldr-s-bl gap","message":"Gunmetal grey — need Battery Junction lists a gunmetal grey Baldr S BL (its page answered 429): a photograph of that colourway before it is offered"},{"level":"gap","where":"part olight-baldr-s-bl gap","message":"How far the body slides on its rail mount — need Olight's manual or a page giving the slide rail's travel: the build draws the body where the side view has it, and on the TX22 its head reaches 0.1 to 0.5 in past the thread protector's rear"},{"level":"gap","where":"part olight-baldr-s-bl gap","message":"A view square across the light (from behind, or from below at a distance) — need The body's width and the jaws are read through a close front photo by their proportions (± 0.04)"},{"level":"gap","where":"part olight-baldr-s-bl gap","message":"The least rail length, and what it fits beyond Picatinny and Glock rails — need A maker's or seller's sentence: none on file names one"},{"level":"gap","where":"part olight-baldr-s-bl gap","message":"Olight's own store page for the Baldr S BL — need olight.com's product page wasn't found; Olight Benelux answered 429 and Olight Australia 404"},{"level":"gap","where":"part otter-creek-polonium-k gap","message":"What barrel thread the mount takes, and what bears on the barrel's shoulder — need Otter Creek's instruction pamphlet (sellers list one in the box; none is hosted where the harvester may read), or the maker's page saved by the user from their own browser"},{"level":"gap","where":"part otter-creek-polonium-k gap","message":"Whether the can is 1.625 in across and 4.8 long as published: sellers' photos read it 3.4% slimmer for its length — need a maker's drawing, or a photo with a scale in the can's own plane; black on white reads thin, and the model keeps both published figures"},{"level":"gap","where":"part otter-creek-polonium-k gap","message":"The front face's pockets: how deep they are — need a view along the face from its edge, or the maker's drawing: a closed pocket shows in no silhouette, and 0.017 in is one oblique photo's reading against the collar's height"},{"level":"gap","where":"part otter-creek-polonium-k gap","message":"Which grooves a unit sold today has: two units photographed differ by 0.04 to 0.05 in — need the maker's page for the current revision"},{"level":"gap","where":"part otter-creek-polonium gap","message":"What barrel thread the mount takes, and what bears on the barrel's shoulder — need Otter Creek's instruction pamphlet (sellers list one in the box; none is hosted where the harvester may read), or the maker's page saved by the user from their own browser"},{"level":"gap","where":"part otter-creek-polonium gap","message":"How far the collar stands out of the front face: 0.062 in by a side photo, 0.12 by an oblique photo of another unit — need a straight side view of the muzzle end with the lens level with the front face, or the maker's drawing"},{"level":"gap","where":"part otter-creek-polonium gap","message":"Whether the can is 1.625 in across and 5.8 long as published, and how long the mount is behind it: the photos read the can 1.4% slimmer for its length, and the mount 0.38 in on this can and 0.44 on the K — need a maker's drawing, or a photo with a scale in the can's own plane"},{"level":"gap","where":"part otter-creek-polonium gap","message":"The front face's pockets: how deep they are — need a view along the face from its edge, or the maker's drawing"},{"level":"gap","where":"part otter-creek-polonium gap","message":"Which grooves a unit sold today has: two units photographed differ by 0.02 to 0.035 in — need the maker's page for the current revision"},{"level":"gap","where":"part panzer-ar57-buffer gap","message":"Its size and look — need A photo of it on its own, or the maker's or a seller's figures"},{"level":"gap","where":"part panzer-ar57-buffer gap","message":"Its weight from the maker or a seller (one buyer's 4.8 oz is all that is on file) — need Panzer Arms' or a seller's figure"},{"level":"gap","where":"part panzer-ar57-buffer gap","message":"Its part number or name, and whether it is sold alone — need A page that lists it"},{"level":"gap","where":"part panzer-ar57-ult-12-upper gap","message":"The left side's plate notch, which no view of this one shows — need A left view of this upper"},{"level":"gap","where":"part panzer-ar57-ult-12-upper gap","message":"Its barrel's diameter and where its breech is (hidden: drawn as the 16 in's) — need A photo of the 12 in barrel out of the upper, or a page's figure"},{"level":"gap","where":"part panzer-ar57-ult-12-upper gap","message":"Its weight: no page gives one for this barrel length — need A seller's or the maker's weight for the 12 in upper alone"},{"level":"gap","where":"part panzer-ar57-ult-16-upper gap","message":"Its width to better than ± 0.06 (read 1.44 through two three-quarter views' cameras, 2026-10-18), and the top flat's under the magazine (assumed 0.835: no view shows it), which the upper chamfers' run is the width less; the front block's sides as they stand (the riser's strip with its holes 0.31 out under the rail's head, a dark band under it, a face below it sloping out to 0.46 to 0.50 at 1.54, through the 12 in's two views from ahead), which the model draws as the rail head's widest carried down to the tray; how far the magazine catch's lever stands out of the rail block's sides (catch_out, assumed 0.3 from the riser's side, so 0.11 nearer the centre each side since the riser was read narrower) — need A photo from straight behind or ahead of it"},{"level":"gap","where":"part panzer-ar57-ult-16-upper gap","message":"Its weight: no page gives one for this barrel length (ar-57center.com: \"Upper Weight ~3 lbs\" for both) — need A seller's or the maker's weight for the 16 in upper alone"},{"level":"gap","where":"part precision-armament-m4-72 gap","message":"The ports' cant upward and the inside between the baffles — need a view into the muzzle end, a section drawing, or photos square on each side and from the front"},{"level":"gap","where":"part precision-armament-m4-72 gap","message":"How deep its thread goes and the hole's size inside — need a photo into its rear end, or the maker's drawing"},{"level":"gap","where":"part precision-armament-m4-72 gap","message":"Why its two published sizes disagree by 2.4% in the maker's own photos — need a seller's straight photo of it from the side on white, or a reviewer's measurement"},{"level":"gap","where":"part precision-armament-m4-72 gap","message":"A design patent, if there is one — need a patent number on the maker's own page or packaging (none on its page or spec sheet)"},{"level":"gap","where":"part primary-arms-deluxe-30mm-mount gap","message":"A view square across the mount (from above, or end on), or any drawing — need none is published: Primary Arms' gallery has two side views and four obliques, and no manual exists (the item feed's manual fields are empty). primaryarmsoptics.com has a page for this mount with a Manuals section and refuses the reader (403): a page the user could save from their own browser"},{"level":"gap","where":"part primary-arms-deluxe-30mm-mount gap","message":"The weight: the maker's 8.2 oz against a reviewer's scale (7.3 oz) and a shop's table (0.198 kg) — need a second weighing, or the maker saying what its figure includes"},{"level":"gap","where":"part primary-arms-deluxe-30mm-mount gap","message":"Heights off the side photos (the base's top, the arm, the split) to better than 0.03 in — need a side view from a long lens, level with the mount; or the mount on a rail in a straight side view"},{"level":"gap","where":"part primary-arms-deluxe-30mm-mount gap","message":"The ring cap screws' size, driver and torque, and the cross bolts' thread — need not stated by Primary Arms or any seller on file; three buyers' reviews give three torques"},{"level":"gap","where":"part primary-arms-deluxe-30mm-mount gap","message":"The nut's recess and the stud's end in it, and the two fine lines drawn as grooves (the split, the bar's seam) — need a close photo of a nut from its end at an angle, and of a ring's split: the depths drawn are assumed and listed"},{"level":"gap","where":"part primary-arms-deluxe-30mm-mount gap","message":"Black matched under the app's light (it is the optics' placeholder) — need scripts/color-match.mjs against the black product photos"},{"level":"gap","where":"part primary-arms-slx-1-6x24-gen-iv gap","message":"A view from either end, or Primary Arms' own dimensioned drawing — need neither manual has a drawing and no page read has an end view: the magnification ring's and the diopter ring's lugs are counted on the half turn each side view shows, and the windage cap and the illumination knob are placed by the manual's small photo from above (66 px to the inch)"},{"level":"gap","where":"part primary-arms-slx-1-6x24-gen-iv gap","message":"A straight side view of this scope itself (the NOVA) — need its own gallery is four three-quarter views: the outlines are traced from the Aurora 5.56 yard sibling's two side views, the same body by Primary Arms' pages"},{"level":"gap","where":"part primary-arms-slx-1-6x24-gen-iv gap","message":"How deep the glass sits at each end, the diopter ring's pockets, the coin slot, and how far the plug on the saddle stands off — need a close photo of each with a scale: the depths drawn are assumed and listed"},{"level":"gap","where":"part primary-arms-slx-1-6x24-gen-iv gap","message":"A reviewer's own weighing; whether the throw lever is in Primary Arms' 17.85 oz — need a scale: the maker's two figures (17.85 oz in the manual, 17.9 oz on the page) are one weight, and neither says whether the lever is on"},{"level":"gap","where":"part primary-arms-slx-1-6x24-gen-iv gap","message":"Black matched under the app's light (it is the optics' placeholder) — need make color-match against the black product photos, as the other black optics"},{"level":"gap","where":"part primary-arms-slx-cantilever-30mm-mount gap","message":"Any published length (overall, ring spacing, ring width, forward reach) — need Primary Arms publishes none and no manual or drawing exists on a page read: every length rests on a camera fitted to the bores in an oblique photo, with a second one 1.1% from it, the rail's pitch 0.8% the other way and the 1.5 in height as its checks"},{"level":"gap","where":"part primary-arms-slx-cantilever-30mm-mount gap","message":"A view square across the mount, from above or end on, and one of its underside — need none in Primary Arms' gallery: the widths are single readings through the fitted camera, the left side's reach, the clamp bar's thickness and the recoil lugs aren't read at all"},{"level":"gap","where":"part primary-arms-slx-cantilever-30mm-mount gap","message":"A photo of it on a rifle or with a scope in it — need none found: which end is the front rests on its being a cantilever and on Primary Arms' guide"},{"level":"gap","where":"part primary-arms-slx-cantilever-30mm-mount gap","message":"The scale to better than 1% — need a published length, or a view with a bore end on: the two cameras fitted to the bores read the rings 3.60 and 3.64 in apart, and three rail slots under the cross bolts would make them 3.57; 3.60 is used"},{"level":"gap","where":"part primary-arms-slx-cantilever-30mm-mount gap","message":"The left side's widths (how far out the bosses' faces are) — need points picked on the rear-left view (ebcd0767a140) through its fitted camera, as the right side's were on the front-right view: drawn as far out as the right side reads"},{"level":"gap","where":"part primary-arms-slx-cantilever-30mm-mount gap","message":"The cross bolts' and cap screws' sizes and drivers — need not published (Torx heads in the photos)"},{"level":"gap","where":"part psa-stealth-stripped-lower gap","message":"the right side: no photo of it is on file (the saved page has two pictures, both of the left). The fence, the roll along the well's right wall, the wall's rear edge and everything else on the right are the standard forging's as read on the catalog's other forged mil-spec lowers — need a photo of this lower's right side, square on, both pin holes open (the user described three photos of it on a bamboo board, its right side, its left and a view down into it: they are not among the saved files)"},{"level":"gap","where":"part psa-stealth-stripped-lower gap","message":"its weight: the page states none; the figure used is the model's volume as 7075 (8.47 oz ± 0.85) — need a page or a reviewer that weighs the stripped receiver"},{"level":"gap","where":"part psa-stealth-stripped-lower gap","message":"a sentence that states its trigger and hammer pin size: the page says 'made by a mil-spec contractor' and nothing of the pins; the small pin is taken from the drawing and from the holes' rims on its close-up photo (0.159 and 0.151 in for .157) — need a seller's sentence"},{"level":"gap","where":"part psa-stealth-stripped-lower gap","message":"a larger copy of its left photo: the saved one is 546 px square (0.017 in to the pixel); the page names a full-size original that isn't on file — need the full-size picture saved from the user's browser"},{"level":"gap","where":"part psa-stealth-stripped-lower gap","message":"the depth of the two oblong pockets by the selector on the left, and whether the bolt catch's bosses stop short of the deck (a bright line 0.04 in under it on the photo) — need an oblique close-up with a known edge beside them, or a view along the receiver"},{"level":"gap","where":"part psa-stripped-upper checklist","message":"upper checklist: \"weight\" still missing"},{"level":"gap","where":"part psa-stripped-upper gap","message":"Its weight — need A page that states one: Palmetto State Armory's gives none, and its site can't be read for another (D59). Not estimated: a build with it says its total weight is unknown"},{"level":"gap","where":"part psa-stripped-upper gap","message":"Its left side, its width, and how far its forward assist housing and deflector stand out — need A view of the left side, and an end or a top view with a known size in frame: the page has one photo, of the right side, and the mil-spec forging's figures stand in"},{"level":"gap","where":"part psa-stripped-upper gap","message":"A larger photo of it — need The page's picture at full size, saved by the user (the saved page holds it 546 px square, 63 px to the inch): every reading on it is good to two or three hundredths, and its outline to a pixel"},{"level":"gap","where":"part psa-stripped-upper gap","message":"A forward assist and a port door for it — need Those parts in the catalog: it is sold without them, and drawn without them"},{"level":"gap","where":"part radian-raptor-charging-handle gap","message":"Radian's own figures — need The maker's public product API verifies current colour identities and image URLs (2026-10-28), including Clear Ano R0140. The weight remains a seller's and a reviewer's, and no length, width or height on file is a maker's figure."},{"level":"gap","where":"part radian-raptor-charging-handle gap","message":"A straight side view — need A photo square to the handle's side (none is on file): the latch's hook arm's two heights, the step from the block down to the ledge behind the shoulder, the plates' thicknesses. The heights drawn are through a camera fitted to one oblique photo and from the design patent's two side views, which agree."},{"level":"gap","where":"part radian-raptor-charging-handle gap","message":"Its seat checked on a photo of it in a receiver — need A pin-framed photo of the handle latched in an upper: it is placed with its shoulder (the ledge's front face) against the front wall of the receiver's notch, as the Army's handle stops. Wing Tactical says it \"May NOT fit on some SIG ARs, specifically the 516 Model\": no SIG receiver is in the catalog, and nothing checks it."},{"level":"gap","where":"part radian-raptor-charging-handle gap","message":"Two colours' numbers on one page each, and two colours not offered — need A second page for the blue's number (R0240 is what is left of AR15Discounts' pair of numbers once the red is R0232) and for Tungsten Grey's (R0002 on Midwest Gun Works' list alone, where it is discontinued); for Black + NP3, a page with the number and a photo large enough to read its colour map. Clear Ano's identity is resolved as R0140 by the maker's public API (2026-10-28), but its image host refuses robots.txt with HTTP 403, so its piece colours remain unverified and it is not selectable. The older R0656 retailer-image filename is not the adopted identifier; that 405 px image cannot resolve the current variant's appearance."},{"level":"gap","where":"part radian-raptor-charging-handle gap","message":"The lower plate's own outline, and the latches' tongues — need A photo square to the handle's underside with the latches in a colour (Wing Tactical's is oblique): under the opening the lower plate is drawn with the opening's outline, and what lies between the two plates there is all the latches' colour, where the real tongues leave a gap at the middle."},{"level":"gap","where":"part radian-raptor-lt-charging-handle gap","message":"Radian's own page — need Its figures and its numbers by colour: the maker's pages are drawn by script and returned only a heading (left alone, D59). A page saved from the user's own browser would give them; until then the weight is one reviewer's weighing, and no length, width or height is a maker's."},{"level":"gap","where":"part radian-raptor-lt-charging-handle gap","message":"A straight side view, and one square to the T's rear — need A photo square to the handle's side or rear (none is on file): the handles' height and where their two faces lie against the plates', read here through a camera fitted to one oblique photo; the panels' depth; the break along the handles' lower rear edges."},{"level":"gap","where":"part radian-raptor-lt-charging-handle gap","message":"A second weighing — need The one weight on file is a reviewer's kitchen scale, to a tenth of an ounce; a seller repeats it. The model can't check it closer than that: no density for the handles' polymer is on file (its aluminium alone comes to 0.96 oz, and all of it as aluminium to 1.48)."},{"level":"gap","where":"part radian-raptor-lt-charging-handle gap","message":"Its seat checked on a photo of it in a receiver — need A pin-framed photo of the handle latched in an upper: it is placed with its shoulder (the ledge's front face) against the front wall of the receiver's notch, as the Army's handle stops. Wing Tactical says it \"*May NOT fit on some SIG AR's, specifically the 516 Model\": no SIG receiver is in the catalog, and nothing checks it. A buyer's review at Primary Arms says it wouldn't seat in his Palmetto State Armory pistol upper until he stoned its side lugs (one report; no rule is made of it)."},{"level":"gap","where":"part radian-raptor-lt-charging-handle gap","message":"The later marking, and Wing Tactical's and Silencer Shop's prices — need Primary Arms' photo of the grey one has US10337811 and USD738452 on its shaft where the black and the Flat Dark Earth ones have USD694354 and USD705384: which handles carry which isn't said by a page. Wing Tactical's page sells the three colours under one offer at the black one's price and a range beside it, and Silencer Shop's markup has no offer: neither is listed."},{"level":"gap","where":"part radian-raptor-sd-charging-handle gap","message":"Radian's own figures — need Radian's page (read now) states no size and no weight: the weight is two sellers' 1.38 oz against a reviewer's and a seller's 1.3 (the ledger's conflict); no length, width or height is a maker's."},{"level":"gap","where":"part radian-raptor-sd-charging-handle gap","message":"The T's top from above, traced — need The plate's outline (its ears round the pins, its arc), the opening the latches leave round it and the logo, picked on Primary Arms' photo of the T from above (e7de8e1a93bd) and carried into the plan by the two pins: until then the plate is the block's width behind a circle through its arc, and round each pin."},{"level":"gap","where":"part radian-raptor-sd-charging-handle gap","message":"A straight view of the left side and the rear — need A photo or render square to the left side (the hook arm's two heights, read here on the design patent) and to the T's rear (the plates and the latches' tongues)."},{"level":"gap","where":"part radian-raptor-sd-charging-handle gap","message":"The ports' exact form — need The ports' walls and holes are read on two renders and the patent's sketch; a drawing or a close photo square to a port's face would give the hole's place on the face and the walls' rounds."},{"level":"gap","where":"part radian-raptor-sd-charging-handle gap","message":"Its seat checked on a photo of it in a receiver — need A pin-framed photo of the handle latched in an upper: it is placed with its shoulder against the front wall of the receiver's notch, as the Army's handle stops. Wing Tactical says it \"May NOT fit on some SIG ARs, specifically the 516 Model\": no SIG receiver is in the catalog."},{"level":"gap","where":"part radian-talon-safety-selector gap","message":"every size: none is published, and all are read from photos scaled by an assumed shaft diameter — need a maker's or reviewer's figure for any one length of it (a lever's length, the shaft between its shoulders), or a photo of it on a rifle square-on with the pins in frame"},{"level":"gap","where":"part radian-talon-safety-selector gap","message":"its weight by a scale: the maker states none and four sellers' figures run from 0.04 oz to 1.92 oz — need a weighed figure for the shaft with its two levers"},{"level":"gap","where":"part radian-talon-safety-selector gap","message":"whether its levers stand off the receiver's sides (.04 a side by the photos) — need a view along the rifle of one installed"},{"level":"gap","where":"part radian-talon-safety-selector gap","message":"the scoop of the head's side facets and the depth of its grooves — need a close view of a lever's head from its top edge"},{"level":"gap","where":"part reptilia-aus-30mm-mount gap","message":"A length, a ring spacing or a drawing from the maker — need Reptilia publishes a bore, a height, a weight and an objective size and nothing else; its installation sheet is words only. The scale rests on one shop's unlabelled 135 mm and the maker's 39 mm read in a 640 px photo: good to about 1.5%"},{"level":"gap","where":"part reptilia-aus-30mm-mount gap","message":"A view from the end (a bore as a circle), or square across the mount — need none on any page read: the rings' section, the bosses' and the clamps' shapes across the rail come from the views from above and below, each scaled at its own depth"},{"level":"gap","where":"part reptilia-aus-30mm-mount gap","message":"The flat dark earth mount's right side (its clamps) and its colour under another light — need the one photograph of it on file (Silencer Shop's, 0bf480654d9e) is of the left side, lit from the left: its clamps are drawn as on the clear and black mounts (black steel), and its colour is fitted to that one lit flank"},{"level":"gap","where":"part reptilia-aus-30mm-mount gap","message":"An offer from a catalog seller for Clear Anodize (100-118) — need Clear is appearance-matched and selectable since 2026-10-28 but unpriced. The maker and Sportsman's Outdoor Superstore confirm the product; none of its sellers is on file, and no black/FDE offer is assigned to it."},{"level":"gap","where":"part reptilia-aus-30mm-mount gap","message":"The cross bolts' own diameter, and the springs behind the clamps — need a picture of a clamp taken off, or the maker's parts list"},{"level":"gap","where":"part reptilia-aus-30mm-mount gap","message":"Whether the cross bolts are 2.41 in apart, as three views read them at the scale the length sets, or six slots (2.364): a conflict kept in the ledger — need a published length from the maker, or a photo of the mount on a rail square on with slots in its plane: scaled by six slots the mount would be 132 mm long and its rings' axis 38.2 mm above its underside. Searched for again on 2026-10-19 (sellers' and reviewers' pages): every picture of it on a rail is the maker's one from the front right and above"},{"level":"gap","where":"part reptilia-aus-30mm-mount gap","message":"Where along a rail the maker means it to go — need its installation sheet says only to push it forward on the rail; its picture has both clamps on the receiver and the front ring over the handguard"},{"level":"gap","where":"part reptilia-dot-mount-193 gap","message":"A view square on to the mount's end, or its width from a page — need The width, the flanges' width and the web's thickness rest on one reader's figures for the lower 1/3 and the maker's two weights; a front or rear view of either height would read them"},{"level":"gap","where":"part reptilia-dot-mount-193 gap","message":"Which dot the maker's 1.93 in is given for — need A sentence naming it: the page names none; its photographs show a CompM5, which isn't on file, and on them the CompM5's axis stands 0.05 in under where a T-2's would (deck_above_rail's two measurements)"},{"level":"gap","where":"part reptilia-dot-mount-193 gap","message":"The deck's lips' height, and the two bars across the channel — need A view square on to the deck's end, and one from below square on to the channel (which slots the bars stand in)"},{"level":"gap","where":"part reptilia-dot-mount-193 gap","message":"A number for the Clear Anodized mount — need The maker's page lists the colour with no number; it is sold only by LiveQordie.com, which no harvested page reads"},{"level":"gap","where":"part reptilia-dot-mount-193 gap","message":"Where the maker means it to go on a rifle — need Its page says only \"attaches to any M1913 Picatinny rail\"; its on-rifle photographs have it on the receiver's rail"},{"level":"gap","where":"part reptilia-dot-mount-39mm gap","message":"What the maker's \"39MM HEIGHT\" is measured to, and for which dot — need A sentence or a drawing: read as a T-2's axis over the rail's top (as Aimpoint names its own 39 mm spacer) it puts the deck 0.12 in under where the maker's own photograph of this mount on a carbine has it (deck_above_rail, a conflict kept)"},{"level":"gap","where":"part reptilia-dot-mount-39mm gap","message":"A view square on to the mount's end, or its width from a page — need The width, the flanges' width and the web's thickness rest on one reader's figures and the maker's two weights; a front or rear view would read them"},{"level":"gap","where":"part reptilia-dot-mount-39mm gap","message":"A larger photograph of it on a rail, square from the side — need The heights rest on a whole-carbine photograph at 28 px an inch; the maker's other views of it on rifles are three-quarter views"},{"level":"gap","where":"part reptilia-dot-mount-39mm gap","message":"The deck's lips' height, and the two bars across the channel — need A view square on to the deck's end, and one from below square on to the channel (which slots the bars stand in)"},{"level":"gap","where":"part reptilia-dot-mount-39mm gap","message":"A number for the Clear Anodize mount — need The maker's page lists the colour with no number; it is sold only by LiveQordie.com, which no harvested page reads"},{"level":"gap","where":"part rosco-bloodline-105-barrel gap","message":"Where the 10.5 in is measured from — need Rosco's statement (taken from the barrel's breech end, as the Army's drawing dimensions a barrel; from the bolt's face it would be an eighth shorter overall)"},{"level":"gap","where":"part rosco-bloodline-105-barrel gap","message":"The profile's diameters and lengths: Rosco publishes none but the journal's .750 and the dimple's .295 — need A maker's drawing; or a straight side photo with a scale in the barrel's plane"},{"level":"gap","where":"part rosco-bloodline-105-barrel gap","message":"The dimple under the journal: its diameter and depth — need Rosco's figure, or a side photo with the dimple on the silhouette"},{"level":"gap","where":"part rosco-bloodline-105-barrel gap","message":"The gas port's diameter — need Rosco's figure (its FAQ withholds it; the one figure on file is a buyer's for the 11.5 in barrel)"},{"level":"gap","where":"part rosco-bloodline-105-barrel gap","message":"The crown: how far across the muzzle's face its cone reaches — need A view of the muzzle from its end, with the thread's diameter in it as the scale"},{"level":"gap","where":"part rosco-bloodline-105-barrel gap","message":"The extension's locking lugs and feed ramps, and the chamber's mouth — need The extension's drawing (8448550 isn't in the package): its inside is the reference CAD set's, turned; hidden once the barrel is in a receiver"},{"level":"gap","where":"part rosco-bloodline-105-barrel gap","message":"The index pin's place on this barrel — need A side photo of this length with the pin on the silhouette (it is the 11.5 in barrel's reading on the same extension)"},{"level":"gap","where":"part rosco-bloodline-115-barrel gap","message":"Where the 11.5 in is measured from — need Rosco's statement (taken from the barrel's breech end, as the Army's drawing dimensions a barrel; from the bolt's face it would be an eighth shorter overall)"},{"level":"gap","where":"part rosco-bloodline-115-barrel gap","message":"The profile's diameters and lengths: Rosco publishes none but the journal's .750 and the dimple's .295 — need A maker's drawing; or a straight side photo with a scale in the barrel's plane"},{"level":"gap","where":"part rosco-bloodline-115-barrel gap","message":"The dimple under the journal: its diameter and depth — need Rosco's figure, or a side photo with the dimple on the silhouette"},{"level":"gap","where":"part rosco-bloodline-115-barrel gap","message":"The gas port's diameter — need Rosco's figure (its FAQ withholds it; .073 is a buyer's, no instrument named)"},{"level":"gap","where":"part rosco-bloodline-115-barrel gap","message":"The crown: how far across the muzzle's face its cone reaches — need A view of the muzzle from its end, with the thread's diameter in it as the scale"},{"level":"gap","where":"part rosco-bloodline-115-barrel gap","message":"The extension's locking lugs and feed ramps, and the chamber's mouth — need The extension's drawing (8448550 isn't in the package): its inside is the reference CAD set's, turned; hidden once the barrel is in a receiver"},{"level":"gap","where":"part rosco-bloodline-125-barrel gap","message":"Where the 12.5 in is measured from — need Rosco's statement (taken from the barrel's breech end, as the Army's drawing dimensions a barrel; from the bolt's face it would be an eighth shorter overall)"},{"level":"gap","where":"part rosco-bloodline-125-barrel gap","message":"The profile's diameters and lengths: Rosco publishes none but the journal's .750 and the dimple's .295 — need A maker's drawing; or a straight side photo with a scale in the barrel's plane"},{"level":"gap","where":"part rosco-bloodline-125-barrel gap","message":"The dimple under the journal: its diameter and depth — need Rosco's figure, or a side photo with the dimple on the silhouette"},{"level":"gap","where":"part rosco-bloodline-125-barrel gap","message":"The gas port's diameter — need Rosco's figure (its FAQ withholds it; the one figure on file is a buyer's for the 11.5 in barrel)"},{"level":"gap","where":"part rosco-bloodline-125-barrel gap","message":"The crown: how far across the muzzle's face its cone reaches — need A view of the muzzle from its end, with the thread's diameter in it as the scale"},{"level":"gap","where":"part rosco-bloodline-125-barrel gap","message":"The extension's locking lugs and feed ramps, and the chamber's mouth — need The extension's drawing (8448550 isn't in the package): its inside is the reference CAD set's, turned; hidden once the barrel is in a receiver"},{"level":"gap","where":"part rosco-bloodline-125-barrel gap","message":"This photo's scale at the breech end: it reads the extension 1% over the Army's limit and 0.03 longer behind the flange than the standard's, with a straight section whose width shows no yaw — need A second straight side photo of this length (Rosco's own of it are three-quarter views), or the maker's drawing"},{"level":"gap","where":"part rosco-bloodline-125-barrel gap","message":"The weight against the model: its volume as steel is 6% over Rosco's 21.79 oz, where its siblings' are 1 and 2% over theirs — need Rosco's confirmation of the 12.5's weight, or a weighing"},{"level":"gap","where":"part sb-tactical-sba3 gap","message":"The housing's width along its length, and its lower part's and the QD block's (only the end cap's block is shown square, from the rear: the housing is drawn at its width, the lower part set in by an assumed 0.12 in) — need a straight view from the front or from below, or the maker's drawing"},{"level":"gap","where":"part sb-tactical-sba3 gap","message":"What the published 6.75 and 9.5 in lengths are measured between (read here as from the end plate's rear face, which the two pictures on a pistol bear out within 0.04 in) — need the maker's words, or a picture of it measured"},{"level":"gap","where":"part sb-tactical-sba3 gap","message":"Its right side (Primary Arms' picture of it is on file and is the left's mirror in every feature; the lever's far plate and the QD socket's far cup are drawn as the near ones) — need nothing: a check only"},{"level":"gap","where":"part sb-tactical-sba4 gap","message":"The brace's own length from its maker (the page's and the sheets' 7.5 in is a length on the rifle from a datum not named: 'Collapsed'); the adopted 7 in is Wing Tactical's — need the maker's drawing or a 'brace only' figure, as the SBA5's sheet gives"},{"level":"gap","where":"part sb-tactical-sba4 gap","message":"Where its lock pin stands, and so which of the tube's six holes its five positions use (it is seated by the maker's picture of it collapsed on a rifle) — need a view from below or a section through the lever, or the maker's words on which holes it uses"},{"level":"gap","where":"part sb-tactical-sba4 gap","message":"Its widths ahead of the cuff: no view from above or below is square, so the housing is drawn at the rear face's section all along and the strut's bars at the rear view's opening — need a straight view from above and from below, or a front view into the mouth"},{"level":"gap","where":"part sb-tactical-sba4 gap","message":"The slots' depth and whether any goes through — need a section or a view into one square"},{"level":"gap","where":"part sb-tactical-sba4 gap","message":"The resin, and the strap's thickness — need the maker's or a seller's words"},{"level":"gap","where":"part sb-tactical-sba5 gap","message":"The housing's and the strut's widths ahead of the cuff (drawn as wide as the end cap) — need a straight view from above or below, or the maker's drawing"},{"level":"gap","where":"part sb-tactical-sba5 gap","message":"Its seat on the tube from a photograph (it is seated by its lock pin in the tube's second hole, ± 0.08 in; the maker's two pistol pictures have its side picture pasted in at two places) — need a straight side photograph of it on a lower with both receiver pins in view, at any position"},{"level":"gap","where":"part sb-tactical-sba5 gap","message":"Its height: the maker states none; Wing Tactical's 5.4 in is 4.5% over what the maker's two pictures give with its length and width (5.16 to 5.18) — need the maker's height, or a second seller's own"},{"level":"gap","where":"part sb-tactical-sba5 gap","message":"How the body is cored (the model is solid, about twice the maker's 9 oz as polymer) — need a view into the cuff or the housing from below, or a section"},{"level":"gap","where":"part sb-tactical-sba5 gap","message":"A design patent or a dimensioned drawing (the maker's patent page lists two utility patents for it, 8,869,444 and 9,354,021, and no design patent) — need a drawing from the maker"},{"level":"gap","where":"part sb-tactical-sbpdw-brace gap","message":"What the published 6.75 in collapsed is measured between (the photos put the brace's rear 7.24 in behind the receiver's rear face) — need the maker's drawing or a sentence saying where the length is taken"},{"level":"gap","where":"part sb-tactical-sbpdw-brace gap","message":"The brace's weight apart from its tube and housing (worked out from the whole's published weight less the tube's aluminium as drawn) — need a review that weighs the brace and the tube apart"},{"level":"gap","where":"part sb-tactical-sbpdw-brace gap","message":"The cuff's section: the view from behind is taken from above it, so its heights are stretched to the side photo's in the model; the body round the tube and the strut's own widths (assumed, body_width) — need a view square from behind or from below, or from the front with a known size in frame"},{"level":"gap","where":"part sb-tactical-sbpdw-brace gap","message":"How the rods are held in the brace and in the housing (off the rifle the maker's two side photos have them 0.3 and 0.9 in further forward than on it) — need the maker's exploded view or a photo of the brace off its housing"},{"level":"gap","where":"part sb-tactical-sbpdw-receiver-extension gap","message":"Not sold alone: no number, no price, no weight of its own (worked out from its sizes as aluminium) — need a page selling the tube and housing alone, or a review that weighs them apart from the brace"},{"level":"gap","where":"part sb-tactical-sbpdw-receiver-extension gap","message":"Its depth (6.920 in) is one seller's; its rear wall, the end of the tube and anything on it are inside the brace in every photo — need the maker's drawing, or a photo of the tube out of the housing and the brace"},{"level":"gap","where":"part sb-tactical-sbpdw-receiver-extension gap","message":"The housing's width at its lower corners (assumed from the rods' spacing and a wall), and the shape of its underside and front from square on — need a view of the assembly from below or from the front, square, with a known size in frame"},{"level":"gap","where":"part sb-tactical-sbpdw-receiver-extension gap","message":"Whether the 'integral' end plate takes a sling (the QD socket the pages name is the housing's, at 6 o'clock: \"QD attachment point at 6 o'clock position on housing\"; no photo on file shows its cup from below) — need a photo of the housing from below"},{"level":"gap","where":"part scalarworks-leap-01-micro-142 gap","message":"A view of the deck from straight above, with a scale — need where the four screw holes and the lug stand on the floor, and the rims' width: only one oblique from above is on file (Wing Tactical's, filed with the 1.57 in, its height not said), so neither is drawn"},{"level":"gap","where":"part scalarworks-leap-01-micro-142 gap","message":"The maker's word on where on the rail it goes — need nothing on its page or in its manual says receiver only or not across the receiver's and the handguard's rails; it is started and advised as any sight is"},{"level":"gap","where":"part scalarworks-leap-01-micro-157 gap","message":"A view of the deck from straight above, with a scale — need where the four screw holes and the lug stand on the floor, and the rims' width: only one oblique from above is on file (Wing Tactical's, its height not said), so neither is drawn"},{"level":"gap","where":"part scalarworks-leap-01-micro-157 gap","message":"The maker's word on where on the rail it goes — need nothing on its page or in its manual says receiver only or not across the receiver's and the handguard's rails; it is started and advised as any sight is"},{"level":"gap","where":"part scalarworks-leap-01-micro-193 gap","message":"A view of the deck from straight above, with a scale — need where the four screw holes and the lug stand on the floor, and the rims' width: only one oblique from above is on file (Wing Tactical's, filed with the 1.57 in, its height not said), so neither is drawn"},{"level":"gap","where":"part scalarworks-leap-01-micro-193 gap","message":"The maker's word on where on the rail it goes — need nothing on its page or in its manual says receiver only or not across the receiver's and the handguard's rails; it is started and advised as any sight is"},{"level":"gap","where":"part scalarworks-leap-02-micro-226 gap","message":"A view of this mount from an end, or a drawing of it — need its own section across (its walls, its window through the ends, the clamp's width) in place of the LEAP/01's, and its deck's floor read on it: none is on the maker's page (no \"diagram\" for SW0230) or a seller's on file"},{"level":"gap","where":"part scalarworks-leap-02-micro-226 gap","message":"A view of the deck from straight above, with a scale — need where the four screw holes and the lug stand on the floor: Primary Arms' oblique from above (4945353b7bdf) shows them, unscaled"},{"level":"gap","where":"part scalarworks-leap-02-micro-226 gap","message":"The maker's word on where on the rail it goes — need nothing on its page says receiver only or not across the receiver's and the handguard's rails; it is started and advised as any sight is"},{"level":"gap","where":"part scalarworks-leap-08-30mm-mount gap","message":"A view of the whole mount from above, from below square on, or from the right — need none is on the maker's page or anywhere found: the beam's width, the blocks' plan and the right-hand jaws are read on one photo from behind and one oblique"},{"level":"gap","where":"part scalarworks-leap-08-30mm-mount gap","message":"Where the right-hand jaw ends and the block over it begins; the jaws' length — need a square view of the mount's right side or underside (a reviewer's photos, once this generation has been reviewed: it was launched 17 Sep 2026)"},{"level":"gap","where":"part scalarworks-leap-08-30mm-mount gap","message":"The metal the model holds over the maker's 161 g (7.04 oz drawn for 5.68) — need the pockets in the clamp blocks' roofs and whatever else lightens the base, which only the oblique from below shows and nothing on file measures: a square view of the underside, or a camera fitted to that oblique by its two bores and the wheels' rims. Where the cantilever's flutes and the pocket under it are set in (0.4 mm a step, 5 mm deep) is assumed for the same want"},{"level":"gap","where":"part scalarworks-leap-08-30mm-mount gap","message":"A photo of this mount on a rifle, and the maker's word on where on the rail it goes — need neither exists on a page read (the three rifle photos on its page are named for the FUSE/02 bolt-on mount); the manual says how it is clamped and nothing of where"},{"level":"gap","where":"part scalarworks-leap-08-30mm-mount gap","message":"The axis's height: the maker's 1.57 in against 1.59 as its own drawing and side photo have it — need a measured review, or the maker's drawing with the height to a tenth of a millimetre"},{"level":"gap","where":"part scalarworks-leap-08-30mm-mount gap","message":"A second seller of SW0815 — need the maker's own shop is the one on file ($419, its markup's SW0815); Primary Arms' page carries no offer in its markup and no word of which generation it is, MidwayUSA's refuses the reader, GRITR's is SW0810"},{"level":"gap","where":"part sig-alpha-msr-30mm gap","message":"A view square across the mount, or SIG's own dimensioned drawing — need none exists in anything reachable (sigsauer.com refuses readers): every width is read through a camera fitted to an oblique photo of the mount alone"},{"level":"gap","where":"part sig-alpha-msr-30mm gap","message":"The mount's weight from SIG — need SIG's ALPHA-MSR page (sigsauer.com refuses fetches)"},{"level":"gap","where":"part sig-alpha-msr-30mm gap","message":"Black matched under the app's light (it is the optics' placeholder) — need scripts/color-match.mjs against the black product photos"},{"level":"gap","where":"part sig-romeo-msr-gen-2 gap","message":"A straight view from the front or the rear — need A studio end view on a plain ground: its sections across (the housing's flanks, the riser's shoulders, the dial's and the windage turret's sizes) are read through a camera fitted to a reviewer's phone photo"},{"level":"gap","where":"part sig-romeo-msr-gen-2 gap","message":"Where the windage turret stands along the sight — need A straight right-side or top view: it is placed level with the elevation turret, where the quarter views show it"},{"level":"gap","where":"part sig-romeo-msr-gen-2 gap","message":"Its weight with the battery in — need SIG's figure is without it, and no page on file gives a CR2032's weight"},{"level":"gap","where":"part sig-romeo-msr-riser-mount gap","message":"A straight view from the front or the rear — need A studio end view on a plain ground: the riser's section across (its shoulders, its legs, its opening) is read through a camera fitted to a reviewer's phone photo"},{"level":"gap","where":"part sig-romeo-msr-riser-mount gap","message":"A page that sells the riser alone, with its own figures — need SIG's riser under a number of its own, with a weight: the weight here is its metal as modelled"},{"level":"gap","where":"part sig-romeo5-gen-ii gap","message":"The weight's configuration — need A page that says whether the manual's 5.5 oz / 155 g includes the I-BEAM mount and the battery: Bereli's page of the Elite says \"without battery\", and the Tall model's 4 g more for a taller mount says the mount is in it, which is how it is taken"},{"level":"gap","where":"part sig-romeo5-gen-ii gap","message":"The right flank, square on — need A view from the rear or from the front with the cap off, or a plan drawing: the housing is drawn symmetric about the axis under the cap and the windage turret"},{"level":"gap","where":"part sig-romeo5-gen-ii gap","message":"The finish of the Flat Dark Earth sight — need A page that says whether SOR5111's flat dark earth is an anodize or a sprayed coat (Cerakote): it is drawn in the black one's matte anodize, its colour matched to Midwest Gun Works' photograph under it"},{"level":"gap","where":"part sig-romeo5-gen-ii gap","message":"SIG's own pages (sigsauer.com) — need They refuse the project's reader and are left alone; a page the user saves from their own browser could be filed"},{"level":"gap","where":"part sig-romeo5-i-beam-mount gap","message":"A page that sells the mount alone, with its own figures — need SIG's I-BEAM under a number of its own, with a weight: the weight here is its metal as modelled, which the Tall model's 4 g says is more than it is"},{"level":"gap","where":"part sig-romeo5-i-beam-mount gap","message":"The M1913 Low Mount — need Its height and its outline: the manual says only \"M1913 Low Mount (Select SKU’s)\" and that it takes the I-BEAM's place under the same four screws; Primary Arms' photo SOR5101_03 shows it lying beside the sight (a flat plate with a clamp), with nothing to scale it by. On a rifle it would put the dot at a height no page states, below an AR's co-witness: the part is drawn on the I-BEAM, as SOR5101 is sold and pictured."},{"level":"gap","where":"part sig-tango-msr-1-6x24 gap","message":"A straight top or end view, or SIG's own dimensioned drawing — need none exists in anything reachable (two discovery passes; sigsauer.com refuses readers): every width here is read through a camera fitted to an oblique photo, the illumination knob's from one viewpoint (± 0.05 in)"},{"level":"gap","where":"part sig-tango-msr-1-6x24 gap","message":"A photo of the scope out of a mount — need every side view on file has the ALPHA-MSR's rings over the tube: where the tube begins and ends each side of the saddle is read beside them, and under them it is taken as the plain tube"},{"level":"gap","where":"part sig-tango-msr-1-6x24 gap","message":"Black matched under the app's light (it is the optics' placeholder); coyote rests on one retailer's two photos — need scripts/color-match.mjs against the black product photos; SIG's own photos of the coyote scope"},{"level":"gap","where":"part silencerco-sparrow-22 gap","message":"The notches' floors between the rear face and where they run out: flat, or the arc of a cutter; and their corners — need a photo straight along a notch from the side, close up (the floor's two ends are measured: 0.356 in from the axis at the rear face, the cap's surface at 0.25 in)"},{"level":"gap","where":"part silencerco-sparrow-22 gap","message":"The rear face: the thread's ring (0.60 in across by the mount-end photo) and the thread's depth — need SilencerCo's drawing, or a photo straight on at the mount end; the model's rear face is a plain flat, and the barrel's thread stands inside it"},{"level":"gap","where":"part silencerco-sparrow-22 gap","message":"The front face: how deep its dish and its eight flutes are, and the collar round the bore — need a straight end-on photo of the muzzle end for their plan, and a second view from another side for their depth: one oblique photo (Primary Arms SU75_00) shows where they are and not how deep. Not drawn until then"},{"level":"gap","where":"part slr-sentry-7-gas-block gap","message":"Its length, height and width — need No page publishes them. A straight side view and a straight front view of SA7-SM, or the maker's figures, would replace the fit and the patent's proportions"},{"level":"gap","where":"part slr-sentry-7-gas-block gap","message":"The rear face — need No photo on file shows it: the gas tube's hole is the patent's (FIG. 4)"},{"level":"gap","where":"part slr-sentry-7-gas-block gap","message":"The flutes' depth and the flat spring's thickness — need A view from the end square to the block, or a photo of the spring edge on"},{"level":"gap","where":"part slr-sentry-7-gas-block gap","message":"The rear set screw's place — need A view square to the underside (the left photo shows the front hole whole and the rear one half hidden by the face's rim)"},{"level":"gap","where":"part spikes-tactical-sdr100a gap","message":"Spike's own figures — need Any size Spike's states for the nut or the ring: every size here is the mil-spec parts'"},{"level":"gap","where":"part spikes-tactical-sdr100a gap","message":"A seller on file — need Spike's Tactical isn't a seller on file; no seller on file was found carrying SDR100A"},{"level":"gap","where":"part streamlight-protac-rail-mount-hl-x interface mlok.reach_inside","message":"needs streamlight-protac-rail-mount-hl-x.reach_inside"},{"level":"gap","where":"part streamlight-protac-rail-mount-hl-x gap","message":"The M-LOK mount's section is read through a camera fitted to four photos of it alone (each figure to 0.03 to 0.05 in); its angle is what it has to fit (135 degrees), 1.4 of the photos' ± from their 129.5; where it then holds the light (the axis 1.20 in above the slot's centre) is 0.06 in above what the maker's side view of the light on it reads (1.14) — need A straight end view of the light on the mount (from the muzzle or the tail), or a drawing of 88300. 1lumen's photos of the HL-X Pro on it (a straight left side view, and one from the tail) and CatOutdoors' right side view of the Rail Mount 1 on it are the best views found; both sites refused the harvester (1lumen's firewall answered the images, CatOutdoors' robots.txt answered 403)"},{"level":"gap","where":"part streamlight-protac-rail-mount-hl-x gap","message":"The light's legs: their width, and the mount's floor between its lips (0.36 in) says they are narrower than the rail they are drawn as wide as — need A view of the light's underside with the clamp off (the scout pattern's two ports), or from its end; then the legs and the clamp's jaws drawn again together"},{"level":"gap","where":"part streamlight-protac-rail-mount-hl-x gap","message":"How the mount fits a particular handguard: it wraps the corner between a side face and the 45-degree face above it, its inner corner 0.31 in above the slot's centre. It sits clear on BCM's MCMR and Geissele's MK16 (lines cast through both models); Aero's R-ONE's side flat runs to 0.33 above its slots and leans 2 degrees, so there its seat's inner corner and its plate's lower edge each stand a hundredth or so into the face — need The inner corner's height to a hundredth (a straight end view), or a photo of it on a handguard whose side face runs higher; Streamlight's own photos show it on a handguard whose side face runs to about the plate's top edge"},{"level":"gap","where":"part streamlight-protac-rail-mount-hl-x gap","message":"The M-LOK mount's weight — need A figure of the piece alone: the one seller's 1.28 oz is the package as boxed (its shipping weight); the build counts the light's published 6.4 oz on either mount"},{"level":"gap","where":"part streamlight-protac-rail-mount-hl-x gap","message":"What the fact sheet's Width (1.45 in) and Height (1.72 in) span — need A dimensioned drawing. The Height matches the span across the head and out to the thumb wheel's end (1.71 to 1.77 in in two photos); the Width is drawn across the head in an infographic, where the photos scaled by the length read 1.42"},{"level":"gap","where":"part streamlight-protac-rail-mount-hl-x gap","message":"A straight side view with a rail in it (how high the body sits, the jaws' hooks, the legs' section) — need A photo of the light clamped on a rail from square to its side, or from its end"},{"level":"gap","where":"part streamlight-protac-rail-mount-hl-x gap","message":"The remote switch, its tail cap and cable, and the retaining clips — need Not rigid parts of the light: not drawn (the category's rule)"},{"level":"gap","where":"part superlative-750-gas-block gap","message":"Its weight — need Six sellers say 1.68 oz and Wing Tactical's table 1.80 oz for the same number; none says what was on the scale. The model as 416 stainless, with its screws and nothing cut inside, is 1.84 oz"},{"level":"gap","where":"part superlative-750-gas-block gap","message":"The gas tube's hole against the standard — need It reads 0.685 in above the bore on the rear photo, 0.060 over the Army's .625; the maker's instruction sheet (on its own site, which refuses the reader, and at Brownells, which refused too) would say which tube it takes and whether the hole is meant high"},{"level":"gap","where":"part superlative-750-gas-block gap","message":"The set screws' places along the foot — need A view square to the underside of the .750 set-screw block (the one on file is oblique, of a stainless block whose diameter isn't said)"},{"level":"gap","where":"part superlative-750-gas-block gap","message":"A camera for the two side photos — need They are close shots from above (the lens some 4 in off by the tab's two thicknesses). A camera fitted to the pin's hole's two rims and the block's edges in each would give every feature on the sides its own correction: the pocket's height (± 0.025 in), the pad's length and the pin's rear end (each read some 5% long, inside their ±)"},{"level":"gap","where":"part superlative-750-gas-block gap","message":"The lasered logo and lettering on the right side — need Primary Arms' right side photo shows them whole (the mark is one bright piece 0.52 in long with four dark islands in it; 'suparms.com' and the patent's number under it; the lot's number is the one block's). They are on the face nearest a close lens in a photo from above: they read some 10% large and 0.07 in low. With the camera for that photo fitted (the gap above) the mark is traced through it onto the ring's surface as its own material slot, as BCM's star is"},{"level":"gap","where":"part superlative-750-gas-block gap","message":"The detent's tab across the face and the adjuster's shank — need A close view of the front from above or below: whether the tab is one thickness, the four flats on the adjuster's neck that the detent bears on (Primary Arms' six are the two sides, the two ends and two three-quarters)"},{"level":"gap","where":"part superlative-750-gas-block gap","message":"How far the adjuster stands out at a working setting — need The maker's sheet: Wing Tactical says 18 clicks from closed is full pressure and 30 more are to be had, four to the turn; the thread's pitch isn't published, so the travel isn't known. Drawn closed, as shipped and as photographed"},{"level":"gap","where":"part surefire-m340c-mini-scout-light-pro interface mlok.reach_inside","message":"needs surefire-m340c-mini-scout-light-pro.reach_inside"},{"level":"gap","where":"part surefire-m340c-mini-scout-light-pro gap","message":"Whether the 3.65 oz counts a mount, and what Primary Arms' 4.1 oz counts — need SureFire says \"W/ BATTERIES\" only; each mount sold apart is 1.6 oz. A page that weighs the light and its mounts apart"},{"level":"gap","where":"part surefire-m340c-mini-scout-light-pro gap","message":"Body diameters other than the bezel's, the mounts' sizes, how many M-LOK slots the mount takes: none is published — need The body's are read on SureFire's own drawing; the mounts' across the body are the Dual Fuel's coarse ratios from three-quarter photos. A square end view of each mount, or SureFire's drawing of the mounts"},{"level":"gap","where":"part surefire-m340c-mini-scout-light-pro gap","message":"The M-1913-S's barrel and plate read 0.05 and 0.04 in longer on this light's photo than on the Dual Fuel's — need A square photo of the M-1913-S alone with something of known size, or SureFire's drawing of it"},{"level":"gap","where":"part surefire-m340c-mini-scout-light-pro gap","message":"How far the M-LOK mount's nuts reach inside the handguard (reach_inside) — need The Magpul instructions the manual says are enclosed with the M-MLOK-S"},{"level":"gap","where":"part surefire-m340c-mini-scout-light-pro gap","message":"Tan rests on the Dual Fuel's match to one seller's photographs; Primary Arms' photographs of the tan M340C read some ten levels darker — need A colour fit (`make color-match`) to Primary Arms' photographs of the M340C, if the two lights' tans are to be told apart"},{"level":"gap","where":"part surefire-m340c-mini-scout-light-pro gap","message":"How far the mount swivels — need SureFire's pages say only that it lets the user optimize the light's position relative to the rail. The build draws one position"},{"level":"gap","where":"part surefire-m340c-mini-scout-light-pro gap","message":"Overall width — need Not published, and it changes with the swivel"},{"level":"gap","where":"part surefire-procomp-556 gap","message":"SureFire's own sheet: its photographs, its \"BODY SPECS 1.0 in\" and its exact wording — need the product information sheet (PROCOMP_PIS.pdf) saved by the user from their own browser: its host's robots.txt refuses the reader"},{"level":"gap","where":"part surefire-procomp-556 gap","message":"The top, square on: where the two top ports stand round the top and how the top pockets end — need a photo square on the top (Primary Arms has the underside; its _00 and _01 see the top from a three-quarter angle)"},{"level":"gap","where":"part surefire-procomp-556 gap","message":"Whether it comes with a crush washer, and how it is timed — need SureFire's sheet or manual for the ProComp; only Cheaper Than Dirt says \"Includes Crush Washer\""},{"level":"gap","where":"part surefire-procomp-556 gap","message":"The inside: the thread's depth, the bore, the slanted faces in the windows, whether the top holes go through — need a section drawing (SureFire's patent-marking page lists patents for its brakes; none on file is tied to the ProComp), or photos straight into both ends and each window"},{"level":"gap","where":"part surefire-procomp-556 gap","message":"Its length: 2.5 in on SureFire's sheet and two sellers, 2.67 in on Cheaper Than Dirt's page — need the maker's sheet itself, or a review's own measurement"},{"level":"gap","where":"part surefire-scout-light-pro-dual-fuel interface mlok.reach_inside","message":"needs surefire-scout-light-pro-dual-fuel.reach_inside"},{"level":"gap","where":"part surefire-scout-light-pro-dual-fuel gap","message":"SureFire's product information sheet (its outline drawing) and its manual — need Both are PDFs on store-fecqh2764q.mybigcommerce.com, whose robots.txt disallows everything, so neither is on file: a copy saved from a browser by the user, or the same documents on a host that allows the reader"},{"level":"gap","where":"part surefire-scout-light-pro-dual-fuel gap","message":"Tan rests on one seller's photographs of one unit; SureFire's tan differs piece to piece (that unit's head ring is darker than its tube) — need A second seller's own photographs of a tan unit, not SureFire's artwork (which is a grey in one copy and a saturated tan in another)"},{"level":"gap","where":"part surefire-scout-light-pro-dual-fuel gap","message":"Body diameter, the mounts' sizes, how many M-LOK slots the mount takes: none is published — need The body's is read from three photos by the bezel; the mounts' across the body are coarse ratios from three-quarter photos. A square end view of each mount, or SureFire's drawing, would settle them"},{"level":"gap","where":"part surefire-scout-light-pro-dual-fuel gap","message":"How far the M-LOK mount's nuts reach inside the handguard (reach_inside) — need The sheet SureFire encloses for the M-MLOK-S (said to be Magpul's), or a figure for its T-nuts"},{"level":"gap","where":"part surefire-scout-light-pro-dual-fuel gap","message":"Which batteries the 5.5 oz is with, and whether a mount is in it — need SureFire's page says \"w/ batteries\" only; each mount alone is 1.6 oz"},{"level":"gap","where":"part surefire-scout-light-pro-dual-fuel gap","message":"How far the mount swivels, and that it goes either side — need SureFire's pages say only that it lets the user optimize the light's position relative to the rail; a reviewer (Shooting Illustrated) says nearly 180 degrees and right or left hand. The build draws one position"},{"level":"gap","where":"part surefire-scout-light-pro-dual-fuel gap","message":"Overall width — need Not published, and it changes with the swivel"},{"level":"gap","where":"part surefire-socom-3-prong gap","message":"Where a SOCOM suppressor's rear face stands on it (suppressor_seat_x) — need a photo of the device with a suppressor locked on, square from the side, or the suppressor's manual's drawing of the two together; the suppressor's own sources may have it"},{"level":"gap","where":"part surefire-socom-3-prong gap","message":"Any diameter as the maker states it: every one is the patent's drawing scaled by the 2.6 in length, which two sellers give as 2.67 — need SureFire's drawing or product sheet (its host refuses the reader), or a seller's table with a diameter"},{"level":"gap","where":"part surefire-socom-3-prong gap","message":"The thread's depth, and the inside between the thread and the tines — need a section drawing, or a photo straight into the rear end"},{"level":"gap","where":"part surefire-socom-3-prong gap","message":"The slanted facet on each tine's inner corner at its tip — need a photo square on the muzzle end: the patent's front view shows where it is and not how deep"},{"level":"gap","where":"part surefire-socom-4-prong gap","message":"Where a SOCOM suppressor's rear face stands on it (suppressor_seat_x) — need a photo of the device with a suppressor locked on, square from the side, or its manual's drawing (71-01-828, on a host that refuses the reader)"},{"level":"gap","where":"part surefire-socom-4-prong gap","message":"The indexing tab and its pockets, the flats' width, and how the slots and flats are turned to the tab — need straight photos from below and from the muzzle end: one straight view is on file, and the tab isn't in it"},{"level":"gap","where":"part surefire-socom-4-prong gap","message":"Any diameter as the maker states it; its length, which SureFire gives as 2.6 in and as 6.4 cm (2.52 in) and a seller as 2.67 — need SureFire's product sheet or drawing"},{"level":"gap","where":"part surefire-socom-4-prong gap","message":"The inside: the thread's depth and the hole through — need a section drawing, or photos straight into both ends"},{"level":"gap","where":"part surefire-socom556-rc2 gap","message":"A view straight at either end — need a photo square on the lock ring's end and one square on the front plate: the opening's size, the ring's wall, the front rim's flats and where they stand round the axis are read off three-quarter views here"},{"level":"gap","where":"part surefire-socom556-rc2 gap","message":"A flute's depth, the latch pocket's depth, and the latch's real shape — need a photo along a flute and one square on the latch with the ring locked, close up; SureFire's manual draws the latch in outline only (Figures 6 and 7A)"},{"level":"gap","where":"part surefire-socom556-rc2 gap","message":"The socket: its steps and tapers, the indexing slot, how deep it is — need SureFire's drawing of the back section, or a photo straight into the rear end; the model's socket is a plain bore at the opening's size"},{"level":"gap","where":"part surefire-socom556-rc2 gap","message":"SureFire's product sheet and the manual's own copy — need they are on SureFire's file host, whose robots.txt disallows them: the user could save SOCOM556-RC2_PIS.pdf from their own browser (it has a photo of a Dark Earth RC2 on a Mk18, by the discovery's account, which would show the seat on a rifle). The manual is on file as Silencer Central hosts it"},{"level":"gap","where":"part surefire-warcomp gap","message":"Where a SOCOM suppressor's rear face stands on it (suppressor_seat_x) — need a photo of the device with a suppressor locked on, square from the side, or the suppressor's manual's drawing of the two together"},{"level":"gap","where":"part surefire-warcomp gap","message":"Any diameter as the maker states it, and the photos' thin reading of a black part — need SureFire's drawing or product sheet (its host refuses the reader), or a straight photo with a scale in the part's plane"},{"level":"gap","where":"part surefire-warcomp gap","message":"The inside: the thread's depth, the hole through, how the ports are drilled and what they open into — need a section drawing (the utility patents SureFire lists against WARCOMP-556, 8,459,406 and 10,274,278, may draw one), or photos straight into both ends"},{"level":"gap","where":"part surefire-warcomp gap","message":"The upper left of the collar, which no straight view on file faces — need a photo square on its top or its left side: the six columns were counted from the upper right, where all show at once"},{"level":"gap","where":"part sylvan-arms-sa5-pro-left-folder gap","message":"A square side view of the part, and one from above: the lengths along the bore rest on one lifestyle photo of a rifle at the scale of the maker's range for the length added, and the hinge's place across on a three-quarter view opened flat. — need A side photo of the part alone or on a lower with its pins in frame; a photo from above, folded and open."},{"level":"gap","where":"part sylvan-arms-sa5-pro-left-folder gap","message":"Its finish: no page names it. — need The maker's or a seller's word for the coating (nitride, phosphate, Cerakote, DLC)."},{"level":"gap","where":"part sylvan-arms-sa5-pro-left-folder gap","message":"Which two of its sockets are the maker's \"2 QD attachment points\": the boss out of the right face, the large hole in the stock half's rear lobe and a round socket in the receiver half's front face below the thread are all on the photos. — need The manual, or a photo of a sling swivel in it."},{"level":"gap","where":"part sylvan-arms-sa5-pro-left-folder gap","message":"Whether the 9.4 oz includes the bolt extension, and the extension's own size: it is scaled here by the length it makes up. — need A seller's or the maker's figure for the extension's length, diameter or weight."},{"level":"gap","where":"part sylvan-arms-sa5-pro-left-folder gap","message":"The User Manual tab on the maker's page is restricted to the reader; no instructions, drawing or patent number is on file. — need The manual (a PDF the maker or a seller hosts), or a patent number on the part or its page."},{"level":"gap","where":"part sylvan-arms-sa5-pro-left-folder gap","message":"MidwayUSA's page (1026993741) refuses the harvester (403); Shiner Tactical's is gone (410). — need Nothing: the maker's, Primary Arms' and AR15Discounts' pages give the figures."},{"level":"gap","where":"part sylvan-arms-sa5-pro-right-folder gap","message":"Any photo of the right-folding one: the sellers' pictures for SA5P-R (AR15Discounts' 307151.png, Monadnock's IQSA5PR-1) show the left one, and the maker's gallery has only the left one. — need A photo of the right-folding one: its right side with the hinge, or a rifle folded to the right."},{"level":"gap","where":"part sylvan-arms-sa5-pro-right-folder gap","message":"Everything the left-folding one lacks (its gaps): a square side view, the finish's name, whether the 9.4 oz has the bolt extension in it, the manual. — need As the left one's."},{"level":"gap","where":"part sylvan-arms-sa5-pro-right-folder gap","message":"Primary Arms and MidwayUSA list only the left one; AR15Discounts has the right one out of stock. — need Nothing: the maker's, AR15Discounts' and Monadnock's pages give its figures."},{"level":"gap","where":"part taurus-tx22-barrel-46 gap","message":"The round barrel's diameter, the chamber block's width and what is under it — need A photo of the barrel out of the slide (a seller's of Taurus's replacement barrel, or the conversion kit's other pictures)"},{"level":"gap","where":"part taurus-tx22-barrel-46 gap","message":"The thread's length — need A page that gives it, or the barrel bare from the side"},{"level":"gap","where":"part taurus-tx22-frame gap","message":"The frame's widths (under the slide, the grip, the trigger guard, the trigger) and how its straps round across — need A view of the pistol from the front and one from behind, square on, from 8 ft or more, zoomed; or the manual's exploded view (Taurus's PDF refuses the reader: a copy the user saves from their own browser)"},{"level":"gap","where":"part taurus-tx22-frame gap","message":"The frame's top under the slide (the rails' tabs and walls, the latch's housing), seen only from close by — need The frame with the slide off, square from its side, from 8 ft or more, zoomed"},{"level":"gap","where":"part taurus-tx22-frame gap","message":"The magazine well as it is (its walls, the flare at its mouth): drawn as the magazine's own size leaves it — need The grip's foot from below, square on, with the magazine out"},{"level":"gap","where":"part taurus-tx22-magazine-16 gap","message":"Every size of it: no page (Taurus's shop, a seller's, a review's) gives one; the sellers' 8.5 in and their weights are a carton's — need Taurus's figures (its manual's parts page, its own site, which refuses the reader), or a review that measures the magazine"},{"level":"gap","where":"part taurus-tx22-magazine-16 gap","message":"Its size: drawn at the scale the catch and the release button give (1.630 in of pad), which also puts its top under the bore and its pad inside the pistol's published width; the pad the pistol's own photos show is 1.73 to 1.76 long (Blackstone's on the rail's pitch, the frame's pins, Sportsman's left view), 8% longer than this magazine's pad at this scale. Either the pistol was photographed with another pad than the sellers' 358-0017-01, or the six pictures of the magazine alone mislead together (no sign of it: square, from four sellers and Taurus) — need A picture of the magazine beside the pistol, or out of it in a picture with something of known size in its plane; or Taurus's figures"},{"level":"gap","where":"part taurus-tx22-magazine-16 gap","message":"Its weight: worked out from the model's polymer (the inside assumed) — need Taurus's figure or a review's weighing"},{"level":"gap","where":"part taurus-tx22-magazine-22 gap","message":"Every size of it: no page gives one (the 16-round's scale carries over, and with it the 16-round's doubt: the pistol's photographed pad is 8% longer than the 16-round's own at this scale) — need Taurus's figures, or a review that measures it"},{"level":"gap","where":"part taurus-tx22-magazine-22 gap","message":"Its sleeve's top against the grip's bottom face: drawn on the 16-round's pad's top line; the square view of the magazine alone has it 0.02 in lower at the sleeve's rear end (1.9 degrees against 1) — need A square side view of it seated in the pistol"},{"level":"gap","where":"part taurus-tx22-magazine-22 gap","message":"Its weight: worked out from the model's polymer (its insides assumed); a catalog's 3.4 oz stands beside it — need Taurus's figure or a review's weighing"},{"level":"gap","where":"part taurus-tx22-thread-protector gap","message":"Its flats (how many, how wide) and its front wall — need The protector off the barrel, stood on end and from the side (a seller's photo of Taurus's replacement protector)"},{"level":"gap","where":"part taurus-tx22-toro-slide gap","message":"The slide's width and its section — need A photo of the pistol from straight ahead or straight behind (any seller's), or Taurus's own page's views, which refuse the reader: a page the user saves from their own browser (D59)"},{"level":"gap","where":"part taurus-tx22-toro-slide gap","message":"The optic cut's footprint (Shield RMSc by Taurus, Holosun K by American Rifleman) and its screw spacing — need A page that dimensions the T.O.R.O.'s cut, or the plate off the slide from above"},{"level":"gap","where":"part toolcraft-556-bcg gap","message":"Anything from Toolcraft itself — need Toolcraft's site has no page, number, weight or drawing for it: every figure is a seller's"},{"level":"gap","where":"part toolcraft-556-bcg gap","message":"A weight that was weighed — need 11.408 oz is one seller's figure (a second page repeats it in the same text); no page says it was put on a scale"},{"level":"gap","where":"part toolcraft-556-bcg gap","message":"What the seller's \"7.7 × 1 × 1.4 in\" measures — need A seller's statement: the drawings' carrier with its bolt forward is 7.46 in long"},{"level":"gap","where":"part unity-fast-micro-226 gap","message":"The deck's height, measured — need a review that measures the deck or the axis of a named dot on it, or Unity's own drawing with the deck dimensioned: the maker's graphic, scaled by its own 2.26 in and by its 2.01 in, puts the deck 1.71 and 1.775 in over the rail; the T-2's figures put it at 1.671 (adopted)"},{"level":"gap","where":"part unity-fast-micro-226 gap","message":"Which dot the 2.26 in is for — need the maker's page (unitytactical.com refuses the reader) or a seller quoting it with a dot named"},{"level":"gap","where":"part unity-fast-micro-226 gap","message":"A square view of the left side, from above and from below — need the rail-grabber bar's length and shape and the deck's plan (its rims, boss, recess and screw holes) are read on obliques and the instruction sheet's drawings only"},{"level":"gap","where":"part unity-fast-micro-226 gap","message":"The Clear and the OD Green — need a seller's page with the colour's number and a photo of it"},{"level":"gap","where":"part unity-fast-micro-226 gap","message":"The maker's own shop — need unitytactical.com refuses the reader; sellers on file carry it"},{"level":"gap","where":"part vg6-gamma-556 gap","message":"A maker's figure for the second generation's length, diameter and weight — need VG6's or Aero's own specification or drawing for APVG200001A (Aero's page leaves \"Weight(s)\" blank; vg6precision.com's page is gone): until then the length is one seller's figure that the photos bear out, and three other sellers print the first generation's 1.75 in"},{"level":"gap","where":"part vg6-gamma-556 gap","message":"The inside: how deep the thread goes, the chambers' shape, the slot's floor, the exit's lobes — need a photo straight into the front face and one into the rear, or a section (VG6's patents, if a marking page ties one to this product)"},{"level":"gap","where":"part vg6-gamma-556 gap","message":"The stainless colourway (APVG200010A) — need a page that sells it by its own number, with a photo of it"},{"level":"gap","where":"part vltor-a5-buffer-spring gap","message":"Its weight — need VLTOR's figure or a scale: 2.23 oz is worked out from its wire's length and steel's density"},{"level":"gap","where":"part vltor-a5-buffer-spring gap","message":"Its free length, wire and diameter as VLTOR makes it — need VLTOR's figures: they are the Army's drawing's of the rifle's spring, which VLTOR says it is"},{"level":"gap","where":"part vltor-a5-receiver-extension gap","message":"The bore's length and the rear wall's thickness — need VLTOR's figure, a drawing, or a section of the tube: the model has the carbine tube's 0.072 wall"},{"level":"gap","where":"part vltor-a5-receiver-extension gap","message":"The position holes' size and exact places, and the channel's width and depth — need a photograph of the rail's underside square on with a known size in frame"},{"level":"gap","where":"part vltor-a5-receiver-extension gap","message":"A slot or notch at the mouth for the buffer retainer (the mil-spec tube's key slot) — need a photograph of the mouth from below; none on file shows it"},{"level":"gap","where":"part vltor-a5h2-buffer gap","message":"Its length — need VLTOR's figure, or a photograph of the A5H2 square from the side with a known size in its plane: the photograph read is a kit picture looking a little down on it, and VLTOR's comparison table (its A5 buffer three quarters of an inch longer than a carbine buffer of 3.25) says 4.0"},{"level":"gap","where":"part vltor-a5h2-buffer gap","message":"The number of flats on its head — need a view of its head face on"},{"level":"gap","where":"part vltor-castle-nut gap","message":"Its sizes — need VLTOR's figures, or a photograph of the nut with a known size in its plane: its outside is the mil-spec nut's and the rest is read as fractions of it on two 1024 px pictures"},{"level":"gap","where":"part vltor-castle-nut gap","message":"Its front face — need A photograph of the nut's front face: whether it has staking notches"},{"level":"gap","where":"part vltor-lockplate gap","message":"Its thickness, its front face and its material — need VLTOR's figures, or a photograph of the plate's edge and front face: every size is the mil-spec plate's, read against VLTOR's two photographs"},{"level":"gap","where":"part vortex-sport-cantilever-30mm-mount gap","message":"A length, a ring spacing or a width from Vortex — need none is published on its page or at any seller read; its parts diagram and instruction card are on a host whose robots.txt disallows the reader (vortexoptics.widen.net) and were left alone"},{"level":"gap","where":"part vortex-sport-cantilever-30mm-mount gap","message":"A view of the mount alone square on from the side, from above, from an end, or of its underside — need none exists in the maker's gallery or any seller's (they all show the maker's four): a seller's or an owner's own photo with a rail or a ruler in it"},{"level":"gap","where":"part vortex-sport-cantilever-30mm-mount gap","message":"The arm's chamfers' angle, and how far the walls with the maker's mark run along the base — need a view of the arm from its end or from below (each side is seen in one picture, which gives a line of widths and drops: drawn at 45 degrees); the walls are drawn between the two clamp blocks"},{"level":"gap","where":"part vortex-sport-cantilever-30mm-mount gap","message":"What Vortex's \"2\\\" Offset\" spans — need a sentence or a drawing from Vortex; on the side view no span of the mount comes to 2 in within its ±"},{"level":"gap","where":"part vortex-sport-cantilever-30mm-mount gap","message":"Black matched under the app's light (it is the optics' placeholder) — need a black on matte anodize isn't fitted to a picture (D81)"},{"level":"gap","where":"build aero-556-fitted.light","message":"M-LOK: the reach inside Aero Precision AR15 15\" R-ONE M-LOK handguard takes isn't sourced (the Aero Precision AR15 15\" R-ONE M-LOK handguard's room inside its side faces, from the face in to the barrel)"},{"level":"gap","where":"build aero-556-fitted.sling_mount","message":"M-LOK: the reach inside Aero Precision AR15 15\" R-ONE M-LOK handguard takes isn't sourced (the Aero Precision AR15 15\" R-ONE M-LOK handguard's room inside its side faces, from the face in to the barrel)"},{"level":"gap","where":"build drop-in-16.hand_stop","message":"M-LOK: the reach inside Magpul MOE® M-LOK® Hand Guard, Mid-Length – AR15/M4 takes isn't sourced (the Magpul MOE® M-LOK® Hand Guard, Mid-Length – AR15/M4's room inside its M-LOK faces before what runs through it)"},{"level":"gap","where":"build suppressed.muzzle","message":"The barrel's muzzle thread is longer than the one this device is made for, and its maker doesn't say how much longer a thread it takes: whether it seats on the shoulder can't be checked (barrel: 0.506, device made for: 0.4)"},{"level":"gap","where":"build two-tone-16.hand_stop","message":"M-LOK: the reach inside MAS Defense 15\" NERO M-LOK FREE FLOAT takes isn't sourced (the MAS Defense 15\" NERO M-LOK FREE FLOAT's room inside an M-LOK face for an accessory's nuts)"}]}